Science.gov

Sample records for aerosol number concentration

  1. Aerosol and cloud droplet number concentrations observed in marine stratocumulus

    SciTech Connect

    Vong, R.J.; Covert, D.S.

    1995-12-01

    The relationship between measurements of cloud droplet number concentration and cloud condensation nuclei (CCN) concentration, as inferred from aerosol size spectra, was investigated at a {open_quote}clean air{close_quote}, marine site (Cheeka Peak) located near the coast of the Olympic Peninsula in Washington State. Preliminary results demonstrated that cloud droplet number increased and droplet diameter decreased as aerosol number concentration (CCN) increased. These results support predictions of a climate cooling due to any future increases in marine aerosol concentrations.

  2. Intercomparison of aerosol instruments: number concentration

    SciTech Connect

    Knutson, E O; Sinclair, D; Tu, K W; Hinchliffe, L; Franklin, H

    1982-05-01

    An intercomparison of aerosol instruments conducted February 23-27, 1981, at the Environmental Measurements Laboratory (EML) focused on five instruments: the Pollak and TSI condensation nucleus counters; the Active Scattering Aerosol Spectrometer (ASAS-X); and two aerosol electrometers. Test aerosols of sodium chloride and ammonium fluorescein generated by nebulization/electrostatic classification were used to obtain 195 lines of comparison data. Concentrations measured by the ASAS-X and the TSI aerosol electrometer averaged respectively 1.388 and 1.581 times that measured by the Pollak. These ratios were very stable during the week and there was little effect of particle size or material. Most other comparisons were equally stable. However, a review of past work at EML and elsewhere led to the disturbing conclusion that these ratios may change from year to year, or from season to season. A filter sample was taken from microscopy, concurrent with readings from the ASAS-X and the TSI condensation nucleus counters. In this sample, the two instruments differed by 20%. Within its 20% uncertainty, the filter result matched both the TSI and ASAS-X readings.

  3. [Characteristics of Number Concentration Size Distributions of Aerosols Under Processes in Beijing].

    PubMed

    Su, Jie; Zhao, Pu-sheng; Chen, Yi-na

    2016-04-15

    The aerosol number concentration size distributions were measured by a Wide-Range Particle Spectrometer (WPS-1000XP) at an urban site of Beijing from 2012 to 2014; and the characteristics of the size distributions in different seasons and weather conditions were discussed. The results showed that the daily average number concentration of Aitken mode aerosols was highest in the spring and lowest in the autumn; the daily average number concentration of accumulation mode aerosols was bigher in the spring and winter, while lowest in summer; and the average concentration of coarse mode was highest during the winter. The Aitken mode particles had the most significant diurnal variations resulted from the traffic sources and the summer photochemical reactions. In the spring, autumn and winter, the number concentrations of accumulation mode of the nighttime was higher than that of the daytime. The coarse mode particles did not have obvious diurnal variation. During the heavy pollution process, the accumulation mode aerosols played a decisive role in PM₂.₅ concentrations and was usually removed by the north wind. The precipitation could effectively eliminate the coarse mode particles, but it bad no obvious effect on the accumulation mode particles under small speed wind and zero speed wind. During the dust process, the concentrations of coarse mode particles increased significantly, while the accumulation mode aerosol concentration was obviously decreased. PMID:27548939

  4. Investigation of Aerosol Surface Area Estimation from Number and Mass Concentration Measurements: Particle Density Effect

    PubMed Central

    Ku, Bon Ki; Evans, Douglas E.

    2015-01-01

    For nanoparticles with nonspherical morphologies, e.g., open agglomerates or fibrous particles, it is expected that the actual density of agglomerates may be significantly different from the bulk material density. It is further expected that using the material density may upset the relationship between surface area and mass when a method for estimating aerosol surface area from number and mass concentrations (referred to as “Maynard’s estimation method”) is used. Therefore, it is necessary to quantitatively investigate how much the Maynard’s estimation method depends on particle morphology and density. In this study, aerosol surface area estimated from number and mass concentration measurements was evaluated and compared with values from two reference methods: a method proposed by Lall and Friedlander for agglomerates and a mobility based method for compact nonspherical particles using well-defined polydisperse aerosols with known particle densities. Polydisperse silver aerosol particles were generated by an aerosol generation facility. Generated aerosols had a range of morphologies, count median diameters (CMD) between 25 and 50 nm, and geometric standard deviations (GSD) between 1.5 and 1.8. The surface area estimates from number and mass concentration measurements correlated well with the two reference values when gravimetric mass was used. The aerosol surface area estimates from the Maynard’s estimation method were comparable to the reference method for all particle morphologies within the surface area ratios of 3.31 and 0.19 for assumed GSDs 1.5 and 1.8, respectively, when the bulk material density of silver was used. The difference between the Maynard’s estimation method and surface area measured by the reference method for fractal-like agglomerates decreased from 79% to 23% when the measured effective particle density was used, while the difference for nearly spherical particles decreased from 30% to 24%. The results indicate that the use of

  5. Production Mechanism, Number Concentration, Size Distribution, Chemical Composition, and Optical Properties of Sea Spray Aerosols Workshop, Summer 2012

    SciTech Connect

    Meskhidze, Nicholas

    2013-10-21

    The objective of this workshop was to address the most urgent open science questions for improved quantification of sea spray aerosol-radiation-climate interactions. Sea spray emission and its influence on global climate remains one of the most uncertain components of the aerosol-radiation-climate problem, but has received less attention than other aerosol processes (e.g. production of terrestrial secondary organic aerosols). Thus, the special emphasis was placed on the production flux of sea spray aerosol particles, their number concentration and chemical composition and properties.

  6. Variability of aerosol particle number concentrations observed over the western Pacific in the spring of 2009

    NASA Astrophysics Data System (ADS)

    Takegawa, N.; Moteki, N.; Oshima, N.; Koike, M.; Kita, K.; Shimizu, A.; Sugimoto, N.; Kondo, Y.

    2014-12-01

    Airborne measurements of aerosols were conducted over the western Pacific in the spring of 2009 during the Aerosol Radiative Forcing in East Asia (A-FORCE) aircraft campaign. The A-FORCE flights intensively covered an important vertical-latitudinal range in the outflow region of East Asia (0-9 km altitude; 27°N-38°N). This paper presents the variability of aerosol particle number concentrations obtained by condensation particle counters and a Single-Particle Soot Photometer (SP2), with the focus on those in the free troposphere. The number concentration data include total condensation nuclei with particle diameters (dp) larger than 10 nm (total CN10), PM0.17-CN10 (dp ~10-130 nm), and SP2 black carbon (NBC; dp ~75-850 nm). Large increases in total CN10 that were not associated with NBC were observed in the free troposphere, suggesting influences from new particle formation (NPF). Statistical characteristics of total CN10, PM0.17-CN10, and NBC in the lower troposphere (LT; 0-3 km), middle troposphere (MT; 3-6 km), and upper troposphere (UT; 6-9 km) are investigated. The correlation between total CN10 and NBC, along with the ratio of PM0.17 to total CN10 and carbon monoxide mixing ratio (CO), is used to interpret the observed variability. The median concentrations of total CN10 and PM0.17-CN10 in the UT were higher than those in the MT by a factor of ~1.4 and ~1.6, respectively. We attribute the enhancements of CN10 in the UT to NPF. Possible mechanisms affecting NPF in the free troposphere are discussed.

  7. Vertical distribution of aerosol number concentration in the troposphere over Siberia derived from airborne in-situ measurements

    NASA Astrophysics Data System (ADS)

    Arshinov, Mikhail Yu.; Belan, Boris D.; Paris, Jean-Daniel; Machida, Toshinobu; Kozlov, Alexandr; Malyskin, Sergei; Simonenkov, Denis; Davydov, Denis; Fofonov, Alexandr

    2016-04-01

    Knowledge of the vertical distribution of aerosols particles is very important when estimating aerosol radiative effects. To date there are a lot of research programs aimed to study aerosol vertical distribution, but only a few ones exist in such insufficiently explored region as Siberia. Monthly research flights and several extensive airborne campaigns carried out in recent years in Siberian troposphere allowed the vertical distribution of aerosol number concentration to be summarized. In-situ aerosol measurements were performed in a wide range of particle sizes by means of improved version of the Novosibirsk-type diffusional particle sizer and GRIMM aerosol spectrometer Model 1.109. The data on aerosol vertical distribution enabled input parameters for the empirical equation of Jaenicke (1993) to be derived for Siberian troposphere up to 7 km. Vertical distributions of aerosol number concentration in different size ranges averaged for the main seasons of the year will be presented. This work was supported by Interdisciplinary integration projects of the Siberian Branch of the Russian Academy of Science No. 35, No. 70 and No. 131; the Branch of Geology, Geophysics and Mining Sciences of RAS (Program No. 5); and Russian Foundation for Basic Research (grant No. 14-05-00526). Jaenicke R. Tropospheric aerosols, in Aerosol-Cloud-Climate Interactions, edited by P.V. Hobs. -Academic Press, San Diego, CA, 1993.- P. 1-31.

  8. Evaluation of the tropospheric aerosol number concentrations simulated by two versions of the global model ECHAM5-HAM

    NASA Astrophysics Data System (ADS)

    Zhang, K.; Kazil, J.; Feichter, J.

    2009-04-01

    Since its first version developed by Stier et al. (2005), the global aerosol-climate model ECHAM5-HAM has gone through further development and updates. The changes in the model include (1) a new time integration scheme for the condensation of the sulfuric acid gas on existing particles, (2) a new aerosol nucleation scheme that takes into account the charged nucleation caused by cosmic rays, and (3) a parameterization scheme explicitly describing the conversion of aerosol particles to cloud nuclei. In this work, simulations performed with the old and new model versions are evaluated against some measurements reported in recent years. The focus is on the aerosol size distribution in the troposphere. Results show that modifications in the parameterizations have led to significant changes in the simulated aerosol concentrations. Vertical profiles of the total particle number concentration (diameter > 3nm) compiled by Clarke et al. (2002) suggest that, over the Pacific in the upper free troposphere, the tropics are associated with much higher concentrations than the mid-latitude regions. This feature is more reasonably reproduced by the new model version, mainly due to the improved results of the nucleation mode aerosols. In the lower levels (2-5 km above the Earth's surface), the number concentrations of the Aitken mode particles are overestimated compared to both the Pacific data given in Clarke et al. (2002) and the vertical profiles over Europe reported by Petzold et al. (2007). The physical and chemical processes that have led to these changes are identified by sensitivity tests. References: Clarke and Kapustin: A Pacific aerosol survey - part 1: a decade of data on production, transport, evolution and mixing in the troposphere, J. Atmos. Sci., 59, 363-382, 2002. Petzold et al.: Perturbation of the European free troposphere aerosol by North American forest fire plumes during the ICARTT-ITOP experiment in summer 2004, Atmos. Chem. Phys., 7, 5105-5127, 2007

  9. Investigation of the seasonal variations of aerosol physicochemical properties and their impact on cloud condensation nuclei number concentration

    NASA Astrophysics Data System (ADS)

    Logan, Timothy S.

    Aerosols are among the most complex yet widely studied components of the atmosphere not only due to the seasonal variability of their physical and chemical properties but also their effects on climate change. The three main aerosol types that are known to affect the physics and chemistry of the atmosphere are: mineral dust, anthropogenic pollution, and biomass burning aerosols. In order to understand how these aerosols affect the atmosphere, this dissertation addresses the following three scientific questions through a combination of surface and satellite observations: SQ1: What are the seasonal and regional variations of aerosol physico-chemical properties at four selected Asian sites? SQ2: How do these aerosol properties change during transpacific and intra-continental long range transport? SQ3: What are the impacts of aerosol properties on marine boundary layer cloud condensation nuclei number concentration? This dissertation uses an innovative approach to classify aerosol properties by region and season to address SQ1. This is useful because this method provides an additional dimension when investigating the physico-chemical properties of aerosols by linking a regional and seasonal dependence to both the aerosol direct and indirect effects. This method involves isolating the aerosol physico-chemical properties into four separate regions using AERONET retrieved Angstrom exponent (AEAOD) and single scattering co-albedo (o oabs) to denote aerosol size and absorptive properties. The aerosols events are then clustered by season. The method is first applied to four AERONET sites representing single mode aerosol dominant regions: weakly absorbing pollution (NASA Goddard), strongly absorbing pollution (Mexico City), mineral dust (Solar Village), and biomass burning smoke (Alta Floresta). The method is then applied to four Asian sites that represent complicated aerosol components. There are strong regional and seasonal influences of the four aerosol types over the

  10. Impact of new particle formation on the concentrations of aerosol number and cloud condensation nuclei around Beijing

    SciTech Connect

    Matsui, H.; Koike, Makoto; Kondo, Yutaka; Takegawa, Nobuyuki; Wiedensohler, A.; Fast, Jerome D.; Zaveri, Rahul A.

    2011-10-13

    New particle formation (NPF) is one of the most important processes in controlling the concentrations of aerosol number (condensation nuclei, CN) and cloud condensation nuclei (CCN) in the atmosphere. In this study, we introduced a new aerosol model representation with 20 size bins between 1 nm and 10 {mu}m and activation-type and kinetic nucleation parameterizations into the WRF-chem model (called NPF-explicit WRF-chem). Model calculations were conducted in the Beijing region in China for the periods during the CARE-Beijing 2006 campaign conducted in August and September 2006. Model calculations successfully reproduced the timing of NPF and no-NPF days in the measurements (21 of 26 days). Model calculations also reproduced the subsequent rapid growth of new particles with a time scale of half a day. These results suggest that once a reasonable nucleation rate at a diameter of 1 nm is given, explicit calculations of condensation and coagulation processes can reproduce the clear contrast between NPF and no-NPF days as well as further growth up to several tens nanometers. With this reasonable representation of the NPF process, we show that NPF contributed 20-30% of CN concentrations (> 10 nm in diameter) in and around Beijing on average. We also show that NPF increases CCN concentrations at higher supersaturations (S > 0.2%), while it decreases them at lower supersaturations (S < 0.1%). This is likely because NPF suppresses the increases in both the size and hygroscopicity of pre-existing particles through the competition of condensable gases between new particles and pre-existing particles. Sensitivity calculations show that a reduction of primary aerosol emissions, such as black carbon (BC), would not necessarily decrease CCN concentrations because of an increase in NPF. Sensitivity calculations also suggest that the reduction ratio of primary aerosol and SO2 emissions will be key in enhancing or damping the BC mitigation effect.

  11. Production Mechanisms, Number Concentration, Size Distribution. Chemical Composition, and Optical Properties of Sea Spray Aerosols

    NASA Technical Reports Server (NTRS)

    Meskhidze, Nicholas; Petters, Markus; Tsigaridis, Kostas; Bates. Tim; O'Dowd, Colin; Reid, Jeff; Lewis, Ernie R.; Gantt, Brett; Anguelova, Magdalena D.; Bhave, Prakash V.; Bird, James; Callaghan, Adrian H.; Ceburnis, Darius; Chang, Rachel; Clark, Antony; deLeeuw, Gerrit; Deane, Grant; DeMott, Paul J.; Elliot, Scott; Facchini, Maria Cristina; Fairall, Chris W.; Hawkins, Lelia; Hu, Yongxiang; Smirnov, Alexander

    2013-01-01

    Over forty scientists from six countries convened in Raleigh, NC on June 4-6 2012 to review the status and prospects of sea spray aerosol research. Participants were researchers from the oceanography and atmospheric science communities, including academia, private industry, and government agencies. The recommendations from the working groups are summarized in a science prioritization matrix that is meant to prioritize the research agenda and identify areas of investigation by the magnitude of their impact on proposed science questions. Str

  12. Global Distribution of Cloud Droplet Number Concentration, Autoconversion Rate, and Aerosol Indirect Effect Under Diabatic Droplet Activation

    NASA Technical Reports Server (NTRS)

    Barahona, Donifan; Sotiropoulou, Rafaella; Nenes, Athanasios

    2011-01-01

    This study presents a global assessment of the sensitivity of droplet number to diabatic activation (i.e., including effects from entrainment of dry air) and its first-order tendency on indirect forcing and autoconversion. Simulations were carried out with the NASA Global Modeling Initiative (GMI) atmospheric and transport model using climatological metereorological fields derived from the former NASA Data Assimilation Office (DAO), the NASA Finite volume GCM (FVGCM) and the Goddard Institute for Space Studies version II (GISS) GCM. Cloud droplet number concentration (CDNC) is calculated using a physically based prognostic parameterization that explicitly includes entrainment effects on droplet formation. Diabatic activation results in lower CDNC, compared to adiabatic treatment of the process. The largest decrease in CDNC (by up to 75 percent) was found in the tropics and in zones of moderate CCN concentration. This leads to a global mean effective radius increase between 0.2-0.5 micrometers (up to 3.5 micrometers over the tropics), a global mean autoconversion rate increase by a factor of 1.1 to 1.7 (up to a factor of 4 in the tropics), and a 0.2-0.4 W m(exp -2) decrease in indirect forcing. The spatial patterns of entrainment effects on droplet activation tend to reduce biases in effective radius (particularly in the tropics) when compared to satellite retrievals. Considering the diabatic nature of ambient clouds, entrainment effects on CDNC need to be considered in GCM studies of the aerosol indirect effect.

  13. Evaluation and modelling of the size fractionated aerosol particle number concentration measurements nearby a major road in Helsinki - Part I: Modelling results within the LIPIKA project

    NASA Astrophysics Data System (ADS)

    Pohjola, M. A.; Pirjola, L.; Karppinen, A.; Härkönen, J.; Korhonen, H.; Hussein, T.; Ketzel, M.; Kukkonen, J.

    2007-08-01

    A field measurement campaign was conducted near a major road "Itäväylä" in an urban area in Helsinki in 17-20 February 2003. Aerosol measurements were conducted using a mobile laboratory "Sniffer" at various distances from the road, and at an urban background location. Measurements included particle size distribution in the size range of 7 nm-10 μm (aerodynamic diameter) by the Electrical Low Pressure Impactor (ELPI) and in the size range of 3-50 nm (mobility diameter) by Scanning Mobility Particle Sizer (SMPS), total number concentration of particles larger than 3 nm detected by an ultrafine condensation particle counter (UCPC), temperature, relative humidity, wind speed and direction, driving route of the mobile laboratory, and traffic density on the studied road. In this study, we have compared measured concentration data with the predictions of the road network dispersion model CAR-FMI used in combination with an aerosol process model MONO32. For model comparison purposes, one of the cases was additionally computed using the aerosol process model UHMA, combined with the CAR-FMI model. The vehicular exhaust emissions, and atmospheric dispersion and transformation of fine and ultrafine particles was evaluated within the distance scale of 200 m (corresponding to a time scale of a couple of minutes). We computed the temporal evolution of the number concentrations, size distributions and chemical compositions of various particle size classes. The atmospheric dilution rate of particles is obtained from the roadside dispersion model CAR-FMI. Considering the evolution of total number concentration, dilution was shown to be the most important process. The influence of coagulation and condensation on the number concentrations of particle size modes was found to be negligible on this distance scale. Condensation was found to affect the evolution of particle diameter in the two smallest particle modes. The assumed value of the concentration of condensable organic

  14. Droplet Number Concentration Value Added Product

    2015-08-06

    Cloud droplet number concentration is an important factor in understanding aerosol-cloud interactions. As aerosol concentration increases, it is expected that droplet number concentration (Nd) will increase and droplet size will decrease, for a given liquid water path. This will greatly affect cloud albedo as smaller droplets reflect more shortwave radiation; however, the magnitude and variability of these processes under different environmental conditions is still uncertain.McComiskey et al. (2009) have implemented a method, based onBoers andmore » Mitchell (1994), for calculating Nd from ground-based remote sensing measurements of optical depth and liquid water path. They show that the magnitude of the aerosol-cloud interactions (ACI) varies with a range of factors, including the relative value of the cloud liquid water path (LWP), the aerosol size distribution, and the cloud updraft velocity. Estimates of Nd under a range of cloud types and conditions and at a variety of sites are needed to further quantify the impacts of aerosol cloud interactions. In order to provide data sets for studying aerosol-cloud interactions, the McComiskey et al. (2009) method was implemented as the Droplet Number Concentration (NDROP) value-added product (VAP).« less

  15. Three years of aerosol mass, black carbon and particle number concentrations at Montsec (southern Pyrenees, 1570 m a.s.l.)

    NASA Astrophysics Data System (ADS)

    Ripoll, A.; Pey, J.; Minguillón, M. C.; Pérez, N.; Pandolfi, M.; Querol, X.; Alastuey, A.

    2014-04-01

    Time variation of mass particulate matter (PM1 and PM1&minus10), black carbon (BC) and number of particles (N3: number of particles with an aerodynamic diameter higher than 3 nm, and N10: higher than 10 nm) concentrations at the high-altitude site of Montsec (MSC) in the southern Pyrenees was interpreted for the period 2010-2012. At MSC, PM10 (12 μg m-3) and N7 (2140 # cm-3) three-year arithmetic average concentrations were higher than those measured at other high-altitude sites in central Europe during the same period (PM10: 3-9 μg m-3 and N: 634-2070 # cm-3). By contrast, BC concentrations at MSC (0.2 μg m-3) were equal to or even lower than those measured at these European sites (0.2-0.4 μg m-3). These differences were attributed to the higher relevance of Saharan dust transport and to the higher importance of the biogenic precursor emissions and new particle formation (NPF) processes, and to the lower influence of anthropogenic emissions at MSC. The different time variation of PM and BC concentrations compared with that of N suggests that these aerosol parameters were governed by diverse factors at MSC. Both PM and BC concentrations showed marked differences for different meteorological scenarios, with enhanced concentrations under North African air outbreaks (PM1&minus10: 13 μg m-3, PM1: 8 μg m-3 and BC: 0.3 μg m-3) and low concentrations when Atlantic advections occurred (PM1-10: 5 μg m-3, PM1: 4 μg m-3 and BC: 0.1 μg m-3). PM and BC concentrations increased in summer, with a secondary maximum in early spring, and were at their lowest in winter, due to the contrasting origin of the air masses in the warmer seasons (spring and summer) and in the colder seasons (autumn and winter). The maximum in the warmer seasons was attributed to long-range transport processes that mask the breezes and regional transport breaking the daily cycles of these pollutants. By contrast, PM and BC concentrations showed clear diurnal cycles, with maxima at midday in the

  16. Estimating Marine Aerosol Particle Volume and Number from Maritime Aerosol Network Data

    NASA Technical Reports Server (NTRS)

    Sayer, A. M.; Smirnov, A.; Hsu, N. C.; Munchak, L. A.; Holben, B. N.

    2012-01-01

    As well as spectral aerosol optical depth (AOD), aerosol composition and concentration (number, volume, or mass) are of interest for a variety of applications. However, remote sensing of these quantities is more difficult than for AOD, as it is more sensitive to assumptions relating to aerosol composition. This study uses spectral AOD measured on Maritime Aerosol Network (MAN) cruises, with the additional constraint of a microphysical model for unpolluted maritime aerosol based on analysis of Aerosol Robotic Network (AERONET) inversions, to estimate these quantities over open ocean. When the MAN data are subset to those likely to be comprised of maritime aerosol, number and volume concentrations obtained are physically reasonable. Attempts to estimate surface concentration from columnar abundance, however, are shown to be limited by uncertainties in vertical distribution. Columnar AOD at 550 nm and aerosol number for unpolluted maritime cases are also compared with Moderate Resolution Imaging Spectroradiometer (MODIS) data, for both the present Collection 5.1 and forthcoming Collection 6. MODIS provides a best-fitting retrieval solution, as well as the average for several different solutions, with different aerosol microphysical models. The average solution MODIS dataset agrees more closely with MAN than the best solution dataset. Terra tends to retrieve lower aerosol number than MAN, and Aqua higher, linked with differences in the aerosol models commonly chosen. Collection 6 AOD is likely to agree more closely with MAN over open ocean than Collection 5.1. In situations where spectral AOD is measured accurately, and aerosol microphysical properties are reasonably well-constrained, estimates of aerosol number and volume using MAN or similar data would provide for a greater variety of potential comparisons with aerosol properties derived from satellite or chemistry transport model data.

  17. Three years of aerosol mass, black carbon and particle number concentrations at Montsec (southern~Pyrenees, 1570 m a.s.l.)

    NASA Astrophysics Data System (ADS)

    Ripoll, A.; Pey, J.; Minguillón, M. C.; Pérez, N.; Pandolfi, M.; Querol, X.; Alastuey, A.

    2013-10-01

    Time variation of mass particulate matter (PM1 and PM1-10), black carbon (BC) and particle number (N) concentrations at the high altitude site of Montsec (MSC) in the southern Pyrenees was interpreted for the period 2010-2012. The MSC site registered higher PM10 (12 μg m-3) and N > 7 nm (2209 # cm-3) concentrations than those measured at other high altitude sites in central Europe (PM10: 3-9 μg m-3 and N: 634-2070 # cm-3). By contrast, BC concentrations at MSC (0.2 μg m-3) were equal or even lower than those measured at these European sites (0.2-0.4 μg m-3). These differences were attributed to the lower influence of anthropogenic emissions and to the higher relevance of Saharan dust transport and new particle formation (NPF) processes at MSC. The different time variation of PM and BC concentrations compared with that of N suggests that these aerosol parameters were governed by diverse factors at MSC. Both PM and BC concentrations showed marked differences for different meteorological scenarios, with enhanced concentrations under North African outbreaks (PM1-10: 13 μg m-3, PM1: 8 μg m-3 and BC: 0.3 μg m-3) and low concentrations when Atlantic advections occurred (PM1-10: 5 μg m-3, PM1: 4 μg m-3 and BC: 0.1 μg m-3). Because of the contrasting origin of the air masses in the warmer seasons (spring and summer) and in the colder seasons (autumn and winter), PM and BC concentrations showed a marked increase in summer, with a secondary maximum in early spring, and were at their lowest during winter. The maximum in the warmer seasons was attributed to long-range transport processes which mask the breezes and regional transport breaking the daily cycles of these pollutants. By contrast, PM and BC concentrations showed clear diurnal cycles with maxima at midday in the colder seasons. A statistically significant weekly variation was also obtained for the BC concentrations, displaying a progressive increase from Tuesday to Saturday, followed by a significant

  18. Workplace aerosol mass concentration measurement using optical particle counters.

    PubMed

    Görner, Peter; Simon, Xavier; Bémer, Denis; Lidén, Göran

    2012-02-01

    Direct-reading aerosol measurement usually uses the optical properties of airborne particles to detect and measure particle concentration. In the case of occupational hygiene, mass concentration measurement is often required. Two aerosol monitoring methods are based on the principle of light scattering: optical particle counting (OPC) and photometry. The former analyses the light scattered by a single particle, the latter by a cloud of particles. Both methods need calibration to transform the quantity of scattered light detected into particle concentration. Photometers are simpler to use and can be directly calibrated to measure mass concentration. However, their response varies not only with aerosol concentration but also with particle size distribution, which frequently contributes to biased measurement. Optical particle counters directly measure the particle number concentration and particle size that allows assessment of the particle mass provided the particles are spherical and of known density. An integrating algorithm is used to calculate the mass concentration of any conventional health-related aerosol fraction. The concentrations calculated thus have been compared with simultaneous measurements by conventional gravimetric sampling to check the possibility of field OPC calibration with real workplace aerosols with a view to further monitoring particle mass concentration. Aerosol concentrations were measured in the food industry using the OPC GRIMM® 1.108 and the CIP 10-Inhalable and CIP 10-Respirable (ARELCO®) aerosol samplers while meat sausages were being brushed and coated with calcium carbonate. Previously, the original OPC inlet had been adapted to sample inhalable aerosol. A mixed aerosol of calcium carbonate and fungi spores was present in the workplace. The OPC particle-size distribution and an estimated average particle density of both aerosol components were used to calculate the mass concentration. The inhalable and respirable aerosol fractions

  19. INDOOR CONCENTRATION MODELING OF AEROSOL STRONG ACIDITY

    EPA Science Inventory

    A model for estimating indoor concentrations of acid aerosol was applied to data collected during the summer of 1989, in a densely populated location in New Jersey. he model, from a study of a semi-rural community in Pennsylvania, was used to estimate indoor concentrations of aer...

  20. Influences of in-cloud aerosol scavenging parameterizations on aerosol concentrations and wet deposition in ECHAM5-HAM

    NASA Astrophysics Data System (ADS)

    Croft, B.; Lohmann, U.; Martin, R. V.; Stier, P.; Wurzler, S.; Feichter, J.; Hoose, C.; Heikkilä, U.; van Donkelaar, A.; Ferrachat, S.

    2009-10-01

    A diagnostic nucleation scavenging scheme, which determines stratiform cloud scavenging ratios for both aerosol mass and number distributions, based on cloud droplet, and ice crystal number concentrations, is introduced into the ECHAM5-HAM global climate model. This is coupled with a size-dependent in-cloud impaction scavenging parameterization for both cloud droplet-aerosol, and ice crystal-aerosol collisions. Sensitivity studies are presented, which compare aerosol concentrations, and deposition between a variety of in-cloud scavenging approaches, including prescribed fractions, several diagnostic schemes, and a prognostic aerosol cloud processing treatment that passes aerosol in-droplet and in-ice crystal concentrations between model time steps. For one sensitivity study, assuming 100% of the in-cloud aerosol is scavenged into the cloud droplets and ice crystals, the annual global mean accumulation mode number burden is decreased by 65%, relative to a simulation with prognostic aerosol cloud processing. Diagnosing separate nucleation scavenging ratios for aerosol number and mass distributions, as opposed to equating the aerosol mass scavenging to the number scavenging ratios, reduces the annual global mean sulfate burden by near to 10%. The annual global mean sea salt burden is 30% lower for the diagnostic approach, which does not carry aerosol in-droplet and in-crystal concentrations between model time-steps as compared to the prognostic scheme. Implementation of in-cloud impaction scavenging reduced the annual, global mean black carbon burden by 30% for the prognostic aerosol cloud processing scheme. Better agreement with observations of black carbon profiles from aircraft (changes near to one order of magnitude for mixed phase clouds), 210Pb surface layer concentrations and wet deposition, and the geographic distribution of aerosol optical depth are found for the new diagnostic scavenging as compared to prescribed ratio scavenging scheme of the standard ECHAM

  1. Inkjet aerosol generator as monodisperse particle number standard

    NASA Astrophysics Data System (ADS)

    Iida, Kenjiro; Sakurai, Hiromu; Ehara, Kensei

    2013-05-01

    Inkjet technology can be applied to generate highly monodisperse aerosol particles in micrometer range at a precisely controlled rate. AIST has been developing an inkjet aerosol generator (AIST-IAG), and the device will soon become the secondary measurement standard for aerosol particle number concentration in 0.35 μm to 10 μm range. The AIST-IAG can generate both solid and liquid particles consisting of water-soluble ionic compounds. We first report the characteristics of the particle sizes of the generated particles. The full width half maximum of the particle size distribution is about 2 percent, and the particle diameter of the IAG particles was calibrated as a function of the particle mass within 0.6-10 μm range using polystyrene latex sphere as reference material. Then we report the capability of the AIST-IAG as the particle number standard. The particle generation efficiency ηIAG was defined as the number of aerosol particles exiting from the AIST-IAG divided by the rate of the droplet generation, and the values of ηIAG within 0.35-10 μm is essentially 100%, and the 95% confidence interval of the values is less than 1%. The result strongly supports that the AISTIAG can be used to calibrate the counting efficiency of the optical particle counters in submicrometer to micrometer range.

  2. Indoor concentration modeling of aerosol strong acidity

    SciTech Connect

    Zelenka, M.; Waldman, J.; Suh, H.; Koutrakis, P.

    1993-01-01

    A model for estimating indoor concentrations of acid aerosol was applied to data collected during the summer of 1989, in a densely populated location in New Jersey. The model, from a study of a semi-rural community in Pennsylvania, was used to estimate indoor concentrations of aerosol strong acidity (H+) at an elderly care residence in suburban New Jersey. The purpose of the present work is to assess the applicability of the model for predicting H+ exposures in a suburban environment and to evaluate the models performance for daytime and nighttime periods. Indoor and outdoor samples were taken at an elderly care home between June 20 and July 30, 1989. The indoor and outdoor monitoring schedule collected two 12-h samples per day. Samples were taken with the Indoor Denuder Sampler (IDS). Samples were analyzed for indoor and outdoor concentrations of aerosol strong acidity (H+), ammonia (NH3), and anion determination. The model generally underestimated the indoor H+ concentration. Slight improvement was seen in the model estimate of H+ for the nighttime period (7:00 pm to 7:00 am, local time). The model applied to the site in New Jersey did not predict the indoor H+ concentrations as well as it did for the experiment from which it was developed.

  3. Polarimetric Retrievals of Cloud Droplet Number Concentrations

    NASA Astrophysics Data System (ADS)

    Sinclair, K.; Cairns, B.; Hair, J. W.; Hu, Y.; Hostetler, C. A.

    2014-12-01

    Cloud droplet number concentration (CDNC) is one of the most significant microphysical properties of liquid clouds and is essential for the understanding of aerosol-cloud interaction. It impacts radiative forcing, cloud evolution, precipitation, global climate and, through observation, can be used to monitor the cloud albedo effect, or the first indirect effect. The IPCC's Fifth Assessment Report continues to consider aerosol-cloud interactions as one of the largest uncertainties in radiative forcing of climate. The SABOR experiment, which was a NASA-led ship and air campaign off the east coast of the United States during July and August of 2014, provided an opportunity for the Research Scanning Polarimeter (RSP) to develop and cross-validate a new approach of sensing CDNC with the High Spectral Resolution Lidar (HSRL). The RSP is an airborne prototype of the Aerosol Polarimetry Sensor (APS) that was on-board the Glory satellite. It is a scanning sensor that provides high-precision measurements of polarized and full-intensity radiances at multiple angles over a wide spectral range. The distinctive feature of the polarimetric technique is that it does not make any assumption of the liquid water profile within the cloud. The approach involves (1) estimating the droplet size distribution from polarized reflectance observations in the rainbow, (2) using polarized reflectance to estimate above cloud water vapor and total reflectance to find how much near infra-red light is being absorbed in clouds, (3) finding cloud physical thickness from the absorption and cloud top pressure retrievals assuming a saturated mixing ratio for water vapor and (4) determining the cloud droplet number concentration from the physical thickness and droplet size distribution retrievals. An overview of the polarimetric technique will be presented along with the results of applying the new approach to SABOR campaign data. An analysis of the algorithm's performance when compared with the HSRL

  4. Variations in Aerosol Size and Number during Discover-Aq

    NASA Astrophysics Data System (ADS)

    Winstead, E.; Thornhill, K. L.; Beyersdorf, A. J.; Hudgins, C.; Ziemba, L. D.; Anderson, B. E.

    2011-12-01

    as short as 1 km. Over the entire experiment, UCN values ranged from 700 to 130,000 cm-3 while particles in the 90 to 1000 nm size range varied from less than 50 to more than 7500 cm-3. The high UCN values typically occurred at times when aerosol scattering and hence surface area was relatively low. Values also tended to increase during the day as gas phase precursors were photochemically oxidized to form less volatile species, which in turn condensed to form new particles. This process was more pronounced on days when background aerosol surface area was relatively low. Accumulation mode number concentrations often increased during the day, as the nucleation mode particles coagulated and aerosol surface increased to the point where deposition of low volatility precursors on existing particles was favored over new particle formation. Particle number concentrations and size also varied considerably from site to site across the 100- by 30-mile study area as a consequence of variations in local sources, humidity, clouds and orographic features. This presentation examines the causes of the variability in more detail and assesses its impact on deriving surface PM properties from satellite observations.

  5. ARM Evaluation Product : Droplet Number Concentration Value-Added Product

    SciTech Connect

    Riihimaki, Laura

    2014-05-15

    Cloud droplet number concentration is an important factor in understanding aerosol-cloud interactions. As aerosol concentration increases, it is expected that droplet number concentration, Nd, will increase and droplet size decrease, for a given liquid water path (Twomey 1977), which will greatly affect cloud albedo as smaller droplets reflect more shortwave radiation. However, the magnitude and variability of these processes under different environmental conditions is still uncertain. McComiskey et al. (2009) have implemented a method, based on Boers and Mitchell (1994), for calculating Nd from ground-based remote sensing measurements of optical depth and liquid water path. They show that the magnitude of the aerosol-cloud interactions (ACI) varies with a range of factors, including the relative value of the cloud liquid water path (LWP), the aerosol size distribution, and the cloud updraft velocity. Estimates of Nd under a range of cloud types and conditions and at a variety of sites are needed to further quantify the impacts of aerosol cloud interactions.

  6. Characterization of Florida red tide aerosol and the temporal profile of aerosol concentration

    PubMed Central

    Cheng, Yung Sung; Zhou, Yue; Pierce, Richard H.; Henry, Mike; Baden, Daniel G.

    2009-01-01

    Red tide aerosols containing aerosolized brevetoxins are produced during the red tide bloom and transported by wind to coastal areas of Florida. This study reports the characterization of Florida red tide aerosols in human volunteer studies, in which an asthma cohort spent 1 h on Siesta Beach (Sarasota, Florida) during aerosolized red tide events and non-exposure periods. Aerosol concentrations, brevetoxin levels, and particle size distribution were measured. Hourly filter samples were taken and analyzed for brevetoxin and NaCl concentrations. In addition, the aerosol mass concentration was monitored in real time. The results indicated that during a non-exposure period in October 2004, no brevetoxin was detected in the water, resulting in non-detectable levels of brevetoxin in the aerosol. In March 2005, the time-averaged concentrations of brevetoxins in water samples were moderate, in the range of 5–10 μg/L, and the corresponding brevetoxin level of Florida red tide aerosol ranged between 21 and 39 ng/m3. The temporal profiles of red tide aerosol concentration in terms of mass, NaCl, and brevetoxin were in good agreement, indicating that NaCl and brevetoxins are components of the red tide aerosol. By continuously monitoring the marine aerosol and wind direction at Siesta Beach, we observed that the marine aerosol concentration varied as the wind direction changed. The temporal profile of the Florida red tide aerosol during a sampling period could be explained generally with the variation of wind direction. PMID:19879288

  7. Theoretical Basis for Convective Invigoration due to Increased Aerosol Concentration

    NASA Astrophysics Data System (ADS)

    Lebo, Z. J.; Chen, Y.; Seinfeld, J.

    2010-12-01

    Recent reports using a one-dimensional parcel model suggest that increases in aerosol number concentration may invigorate deep convection by mitigating the autoconversion process until air parcels reach the freezing level. This would lead to an increase in ice water aloft and the potential for enhanced upward heat transport due to phase changes, hence leading to invigorated convection. Other studies have proposed that an increase in aerosol loading may act to increase cloud top height, increasing the liquid water content, which ultimately increases the cumulative precipitation. Here we study the effect of aerosol perturbations on deep convection by employing the Weather Research and Forecasting model as a three-dimensional CRM with a two-moment, six-class bulk microphysics scheme. These results are corroborated using a newly developed bin microphysics scheme. The bulk microphysics scheme is augmented with a state-of-the-art activation scheme based on Köhler Theory and Population Splitting to analyze the effect of CCN perturbations on cloud development. Moreover, we include a physically-based parameterization for homogeneous and heterogeneous freezing to determine the effects of changes in IN number concentration on deep convective cloud development. We perform idealized simulations of deep convection over a wide range of CCN concentrations (i.e., 102 to 103 cm-3), which encompasses clean maritime conditions to polluted continental conditions, respectively. The detailed model calculations reveal that the CCN effect on precipitation in deep convective clouds depends strongly on the ambient water vapor mixing ratio profile. Our simulations suggest that under relatively dry conditions, an increase in aerosol number concentration leads to a decrease in precipitation (-4.2%), while under moist conditions, an increase in aerosol number concentration leads to an increase in precipitation (8.1%). However, when the water vapor in the mid- to upper-troposphere is depleted

  8. Improving aerosol distributions below clouds by assimilating satellite-retrieved cloud droplet number

    PubMed Central

    Saide, Pablo E.; Carmichael, Gregory R.; Spak, Scott N.; Minnis, Patrick; Ayers, J. Kirk

    2012-01-01

    Limitations in current capabilities to constrain aerosols adversely impact atmospheric simulations. Typically, aerosol burdens within models are constrained employing satellite aerosol optical properties, which are not available under cloudy conditions. Here we set the first steps to overcome the long-standing limitation that aerosols cannot be constrained using satellite remote sensing under cloudy conditions. We introduce a unique data assimilation method that uses cloud droplet number (Nd) retrievals to improve predicted below-cloud aerosol mass and number concentrations. The assimilation, which uses an adjoint aerosol activation parameterization, improves agreement with independent Nd observations and with in situ aerosol measurements below shallow cumulus clouds. The impacts of a single assimilation on aerosol and cloud forecasts extend beyond 24 h. Unlike previous methods, this technique can directly improve predictions of near-surface fine mode aerosols responsible for human health impacts and low-cloud radiative forcing. Better constrained aerosol distributions will help improve health effects studies, atmospheric emissions estimates, and air-quality, weather, and climate predictions. PMID:22778436

  9. Influences of in-cloud aerosol scavenging parameterizations on aerosol concentrations and wet deposition in ECHAM5-HAM

    NASA Astrophysics Data System (ADS)

    Croft, B.; Lohmann, U.; Martin, R. V.; Stier, P.; Wurzler, S.; Feichter, J.; Hoose, C.; Heikkilä, U.; van Donkelaar, A.; Ferrachat, S.

    2010-02-01

    A diagnostic cloud nucleation scavenging scheme, which determines stratiform cloud scavenging ratios for both aerosol mass and number distributions, based on cloud droplet, and ice crystal number concentrations, is introduced into the ECHAM5-HAM global climate model. This scheme is coupled with a size-dependent in-cloud impaction scavenging parameterization for both cloud droplet-aerosol, and ice crystal-aerosol collisions. The aerosol mass scavenged in stratiform clouds is found to be primarily (>90%) scavenged by cloud nucleation processes for all aerosol species, except for dust (50%). The aerosol number scavenged is primarily (>90%) attributed to impaction. 99% of this impaction scavenging occurs in clouds with temperatures less than 273 K. Sensitivity studies are presented, which compare aerosol concentrations, burdens, and deposition for a variety of in-cloud scavenging approaches: prescribed fractions, a more computationally expensive prognostic aerosol cloud processing treatment, and the new diagnostic scheme, also with modified assumptions about in-cloud impaction and nucleation scavenging. Our results show that while uncertainties in the representation of in-cloud scavenging processes can lead to differences in the range of 20-30% for the predicted annual, global mean aerosol mass burdens, and near to 50% for accumulation mode aerosol number burden, the differences in predicted aerosol mass concentrations can be up to one order of magnitude, particularly for regions of the middle troposphere with temperatures below 273 K where mixed and ice phase clouds exist. Different parameterizations for impaction scavenging changed the predicted global, annual mean number removal attributed to ice clouds by seven-fold, and the global, annual dust mass removal attributed to impaction by two orders of magnitude. Closer agreement with observations of black carbon profiles from aircraft (increases near to one order of magnitude for mixed phase clouds), mid

  10. Effects of aerosol organics on cloud condensation nucleus (CCN) concentration and first indirect aerosol effect

    SciTech Connect

    Wang, J. X.; Lee, Y.- N.; Daum, Peter H.; Jayne, John T.; Alexander, M. L.

    2008-11-03

    Abstract. Aerosol microphysics, chemical composition, and CCN properties were measured on the Department of Energy Gulfstream-1 aircraft during the Marine Stratus/ Stratocumulus Experiment (MASE) conducted over the coastal waters between Point Reyes National Seashore and Monterey Bay, California, in July 2005. Aerosols measured during MASE included free tropospheric aerosols, marine boundary layer aerosols, and aerosols with high organic concentration within a thin layer above the cloud. Closure analysis was carried out for all three types of aerosols by comparing the measured CCN concentrations at 0.2% supersaturation to those predicted based on size distribution and chemical composition using K¨ohler theory. The effect of aerosol organic species on predicted CCN concentration was examined using a single hygroscopicity parameterization.

  11. Can anthropogenic aerosol concentrations effect the snowfall rate?

    NASA Astrophysics Data System (ADS)

    Lohmann, U.; Zhang, J.; Pi, J.

    2003-04-01

    The mesoscale model GESIMA is used to simulate microphysical properties of Arctic clouds and their effect on radiation. Different case studies during the FIRE.ACE/SHEBA project show that GESIMA is able to simulate the cloud boundaries, ice and liquid water content and effective radii in good agreement with observations. For two different aerosol scenarios, the simulation results show that the anthropogenic aerosol can alter microphysical properties of Arctic clouds, and consequently modify surface precipitation. Borys et al. (2000) proposed that anthropogenically-induced decreases in cloud droplet size inhibit the riming process. On the contrary, we find that the accretion of snow crystals with cloud droplets is increased in the polluted cloud due to its higher cloud droplet number concentration. Instead the autoconversion rate of cloud droplets and accretion of drizzle by snow decreases caused by the shut-down of the collision-coalescence process in the polluted cloud. The amount of precipitation reaching the surface as snow depends crucially on the crystal shape. If aggregates are assumed, then a 10-fold increase in aerosol concentration leads to an increase in accumulated snow by 40% after 7 hours of simulation whereas the snow amount decreases by 30% when planar crystals are assumed because of the larger accretion efficiency of snow crystals with cloud droplets in case of aggregates. We will also perform climate model simulations to estimate the importance of this effect globally.

  12. Anthropogenic sulfate and organic aerosols, CCN, and cloud project concentration at a marine site

    SciTech Connect

    Novakao, T.; Rivera-Carpio, C.; Penner, J.E.; Rogers, C.F.

    1993-10-01

    The need to establish the relationships between the number concentration of cloud droplets, cloud condensation nuclei (CCN), and the mass concentrations of major aerosol species has been heightened by the results of recent modeling studies suggesting that anthropogenic sulfate and biomass smoke aerosols may cause a globally averaged climate forcing comparable in magnitude but opposite in sign to the forcing due to ``greenhouse`` gases. In this paper we present the results of measurements of nonseasalt (nss) sulfate and organic carbon mass concentrations and mass size distributions, CCN, and cloud droplet number concentrations obtained in 1991 and 1992 on El Yunque peak, Puerto Rico . This peak (18{degree}19N, 65{degree}45W; elevation 1000 m) is located the eastern end of the island, directly exposed to the ocean winds and frequently covered with clouds. Our results show that although CCN number concentrations (measured at 0.5% supersaturation) and nss sulfate mass concentrations are significantly correlated at this site, estimates based on measured mass size distributions of organic and sulfate aerosols indicate that the organic aerosols may account for the majority of CCN number concentrations. Droplet concentrations in the cumulus clouds do not show a discernible trend with nss sulfate mass concentrations. In stratocumulus clouds a small increase in droplet concentrations with nss sulfate mass concentrations was observed.

  13. Unexpectedly high ultrafine aerosol concentrations above East Antarctic sea ice

    NASA Astrophysics Data System (ADS)

    Humphries, R. S.; Klekociuk, A. R.; Schofield, R.; Keywood, M.; Ward, J.; Wilson, S. R.

    2016-02-01

    Better characterisation of aerosol processes in pristine, natural environments, such as Antarctica, have recently been shown to lead to the largest reduction in uncertainties in our understanding of radiative forcing. Our understanding of aerosols in the Antarctic region is currently based on measurements that are often limited to boundary layer air masses at spatially sparse coastal and continental research stations, with only a handful of studies in the vast sea-ice region. In this paper, the first observational study of sub-micron aerosols in the East Antarctic sea ice region is presented. Measurements were conducted aboard the icebreaker Aurora Australis in spring 2012 and found that boundary layer condensation nuclei (CN3) concentrations exhibited a five-fold increase moving across the polar front, with mean polar cell concentrations of 1130 cm-3 - higher than any observed elsewhere in the Antarctic and Southern Ocean region. The absence of evidence for aerosol growth suggested that nucleation was unlikely to be local. Air parcel trajectories indicated significant influence from the free troposphere above the Antarctic continent, implicating this as the likely nucleation region for surface aerosol, a similar conclusion to previous Antarctic aerosol studies. The highest aerosol concentrations were found to correlate with low-pressure systems, suggesting that the passage of cyclones provided an accelerated pathway, delivering air masses quickly from the free troposphere to the surface. After descent from the Antarctic free troposphere, trajectories suggest that sea-ice boundary layer air masses travelled equatorward into the low-albedo Southern Ocean region, transporting with them emissions and these aerosol nuclei which, after growth, may potentially impact on the region's radiative balance. The high aerosol concentrations and their transport pathways described here, could help reduce the discrepancy currently present between simulations and observations of

  14. Potential source identification for aerosol concentrations over a site in Northwestern India

    NASA Astrophysics Data System (ADS)

    Payra, Swagata; Kumar, Pramod; Verma, Sunita; Prakash, Divya; Soni, Manish

    2016-03-01

    The collocated measurements of aerosols size distribution (ASD) and aerosol optical thickness (AOT) are analyzed simultaneously using Grimm aerosol spectrometer and MICROTOP II Sunphotometer over Jaipur, capital of Rajasthan in India. The contrast temperature characteristics during winter and summer seasons of year 2011 are investigated in the present study. The total aerosol number concentration (TANC, 0.3-20 μm) during winter season was observed higher than in summer time and it was dominated by fine aerosol number concentration (FANC < 2 μm). Particles smaller than 0.8 μm (at aerodynamic size) constitute ~ 99% of all particles in winter and ~ 90% of particles in summer season. However, particles greater than 2 μm contribute ~ 3% and ~ 0.2% in summer and winter seasons respectively. The aerosols optical thickness shows nearly similar AOT values during summer and winter but corresponding low Angstrom Exponent (AE) values during summer than winter, respectively. In this work, Potential Source Contribution Function (PSCF) analysis is applied to identify locations of sources that influenced concentrations of aerosols over study area in two different seasons. PSCF analysis shows that the dust particles from Thar Desert contribute significantly to the coarse aerosol number concentration (CANC). Higher values of the PSCF in north from Jaipur showed the industrial areas in northern India to be the likely sources of fine particles. The variation in size distribution of aerosols during two seasons is clearly reflected in the log normal size distribution curves. The log normal size distribution curves reveals that the particle size less than 0.8 μm is the key contributor in winter for higher ANC.

  15. Effect of aerosol concentration and absorbing aerosol on the radiation fog life cycle

    NASA Astrophysics Data System (ADS)

    Maalick, Z.; Kühn, T.; Korhonen, H.; Kokkola, H.; Laaksonen, A.; Romakkaniemi, S.

    2016-05-01

    Analogous to cloud formation, the formation and life cycle of fogs is largely influenced by aerosol particles. The objective of this work is to analyze how changes in aerosol properties affect the fog life cycle, with special emphasis on how droplet concentrations change with cloud condensation nuclei (CCN) concentrations and on the effect that absorbing black carbon (BC) particles have on fog dissipation. For our simulation case study, we chose a typical fall time radiation fog at mid-latitudes (45° north) in fairly highly polluted conditions. Our results show that CCN concentrations have a strong influence on the fog lifetime. This is because the immediate effect of CCN on cloud droplet number concentrations (CDNC) is enhanced through two positive feedback loops: (1) Higher CDNC leads to more radiative cooling at the fog top, which leads to even stronger activation and (2) if CDNC is higher, the average droplet size is smaller, which slows down droplet removal through sedimentation. The effect that radiation fogs have on solar surface irradiation is large - the daily mean can change by 50% if CCN concentrations are doubled or halved (considering a reference CCN mixing ratio of 800 #/mg). With the same changes in CCN, the total fog lifetime increases 160 min or decreases 65 min, respectively. Although BC has a noticeable effect on fog height and dissipation time, its relative effect compared to CCN is small, even if BC concentrations are high. The fog formation is very sensitive to initial meteorological conditions which may be altered considerably if fog was present the previous day. This effect was neglected here, and future simulations, which span several days, may thus be a valuable extension of this study.

  16. The importance of aerosol composition and mixing state on predicted CCN concentration and the variation of the importance with atmospheric processing of aerosol

    SciTech Connect

    Wang, J.; Cubison, M.; Aiken, A.; Jimenez, J.; Collins, D.; Gaffney, J.; Marley, N.

    2010-03-15

    The influences of atmospheric aerosols on cloud properties (i.e., aerosol indirect effects) strongly depend on the aerosol CCN concentrations, which can be effectively predicted from detailed aerosol size distribution, mixing state, and chemical composition using Köhler theory. However, atmospheric aerosols are complex and heterogeneous mixtures of a large number of species that cannot be individually simulated in global or regional models due to computational constraints. Furthermore, the thermodynamic properties or even the molecular identities of many organic species present in ambient aerosols are often not known to predict their cloud-activation behavior using Köhler theory. As a result, simplified presentations of aerosol composition and mixing state are necessary for large-scale models. In this study, aerosol microphysics, CCN concentrations, and chemical composition measured at the T0 urban super-site in Mexico City during MILAGRO are analyzed. During the campaign in March 2006, aerosol size distribution and composition often showed strong diurnal variation as a result of both primary emissions and aging of aerosols through coagulation and local photochemical production of secondary aerosol species. The submicron aerosol composition was ~1/2 organic species. Closure analysis is first carried out by comparing CCN concentrations calculated from the measured aerosol size distribution, mixing state, and chemical composition using extended Köhler theory to concurrent CCN measurements at five supersaturations ranging from 0.11% to 0.35%. The closure agreement and its diurnal variation are studied. CCN concentrations are also derived using various simplifications of the measured aerosol mixing state and chemical composition. The biases associated with these simplifications are compared for different supersaturations, and the variation of the biases is examined as a function of aerosol age. The results show that the simplification of internally mixed, size

  17. Aerosol number size distributions over a coastal semi urban location: Seasonal changes and ultrafine particle bursts.

    PubMed

    Babu, S Suresh; Kompalli, Sobhan Kumar; Moorthy, K Krishna

    2016-09-01

    Number-size distribution is one of the important microphysical properties of atmospheric aerosols that influence aerosol life cycle, aerosol-radiation interaction as well as aerosol-cloud interactions. Making use of one-yearlong measurements of aerosol particle number-size distributions (PNSD) over a broad size spectrum (~15-15,000nm) from a tropical coastal semi-urban location-Trivandrum (Thiruvananthapuram), the size characteristics, their seasonality and response to mesoscale and synoptic scale meteorology are examined. While the accumulation mode contributed mostly to the annual mean concentration, ultrafine particles (having diameter <100nm) contributed as much as 45% to the total concentration, and thus constitute a strong reservoir, that would add to the larger particles through size transformation. The size distributions were, in general, bimodal with well-defined modes in the accumulation and coarse regimes, with mode diameters lying in the range 141 to 167nm and 1150 to 1760nm respectively, in different seasons. Despite the contribution of the coarse sized particles to the total number concentration being meager, they contributed significantly to the surface area and volume, especially during transport of marine air mass highlighting the role of synoptic air mass changes. Significant diurnal variation occurred in the number concentrations, geometric mean diameters, which is mostly attributed to the dynamics of the local coastal atmospheric boundary layer and the effect of mesoscale land/sea breeze circulation. Bursts of ultrafine particles (UFP) occurred quite frequently, apparently during periods of land-sea breeze transitions, caused by the strong mixing of precursor-rich urban air mass with the cleaner marine air mass; the resulting turbulence along with boundary layer dynamics aiding the nucleation. These ex-situ particles were observed at the surface due to the transport associated with boundary layer dynamics. The particle growth rates from

  18. MCS precipitation and downburst intensity response to increased aerosol concentrations

    NASA Astrophysics Data System (ADS)

    Clavner, M.; Cotton, W. R.; van den Heever, S. C.

    2015-12-01

    Mesoscale convective systems (MCSs) are important contributors to rainfall in the High Plains of the United States as well as producers of severe weather such as hail, tornados and straight-line wind events known as derechos. Past studies have shown that changes in aerosol concentrations serving as cloud condensation nuclei (CCN) alter the MCS hydrometeor characteristics which in turn modify precipitation yield, downdraft velocity, cold-pool strength, storm propagation and the potential for severe weather to occur. In this study, the sensitivity of MCS precipitation characteristics and convective downburst velocities associated with a derecho to changes in CCN concentrations were examined by simulating a case study using the Regional Atmospheric Modeling System (RAMS). The case study of the 8 May 2009 "Super-Derecho" MCS was chosen since it produced a swath of widespread wind damage in association with an embedded large-scale bow echo, over a broad region from the High Plains of western Kansas to the foothills of the Appalachians. The sensitivity of the storm to changes in CCN concentrations was examined by conducting a set of three simulations which differed in the initial aerosol concentration based on output from the 3D chemical transport model, GEOS-Chem. Results from this study indicate that while increasing CCN concentrations led to an increase in precipitation rates, the changes to the derecho strength were not linear. A moderate increase in aerosol concentration reduced the derecho strength, while the simulation with the highest aerosol concentrations increased the derecho intensity. These changes are attributed to the impact of enhanced CCN concentration on the production of convective downbursts. An analysis of aerosol loading impacts on these MCS features will be presented.

  19. Determination of seasonal, diurnal, and height resolved average number concentration in a pollution impacted rural continental location

    NASA Astrophysics Data System (ADS)

    Bullard, Robert L.; Stanier, Charles O.; Ogren, John A.; Sheridan, Patrick J.

    2013-05-01

    The impact of aerosols on Earth's radiation balance and the associated climate forcing effects of aerosols represent significant uncertainties in assessment reports. The main source of ultrafine aerosols in the atmosphere is the nucleation and subsequent growth of gas phase aerosol precursors into liquid or solid phase particles. Long term records of aerosol number, nucleation event frequency, and vertical profiles of number concentration are rare. The data record from multiagency monitoring assets at Bondville, IL can contribute important information on long term and vertically resolved patterns. Although particle number size distribution data are only occasionally available at Bondville, highly time-resolved particle number concentration data have been measured for nearly twenty years by the NOAA ESRL Global Monitoring Division. Furthermore, vertically-resolved aerosol counts and other aerosol physical parameters are available from more than 300 flights of the NOAA Airborne Aerosol Observatory (AAO). These data sources are used to better understand the seasonal, diurnal, and vertical variation and trends in atmospheric aerosols. The highest peaks in condensation nuclei greater than 14 nm occur during the spring months (May, April) with slightly lower peaks during the fall months (September, October). The diurnal pattern of aerosol number has a midday peak and the timing of the peak has seasonal patterns (earlier during warm months and later during colder months). The seasonal and diurnal patterns of high particle number peaks correspond to seasons and times of day associated with low aerosol mass and surface area. Average vertical profiles show a nearly monotonic decrease with altitude in all months, and with peak magnitudes occurring in the spring and fall. Individual flight tracks show evidence of plumes (i.e., enhanced aerosol number is limited to a small altitude range, is not homogeneous horizontally, or both) as well as periods with enhanced particle number

  20. Sensitivity of aerosol concentrations and cloud properties to nucleation and secondary organic distribution in ECHAM5-HAM global circulation model

    NASA Astrophysics Data System (ADS)

    Makkonen, R.; Asmi, A.; Korhonen, H.; Kokkola, H.; Järvenoja, S.; Räisänen, P.; Lehtinen, K. E. J.; Laaksonen, A.; Kerminen, V.-M.; Järvinen, H.; Lohmann, U.; Bennartz, R.; Feichter, J.; Kulmala, M.

    2009-03-01

    The global aerosol-climate model ECHAM5-HAM was modified to improve the representation of new particle formation in the boundary layer. Activation-type nucleation mechanism was introduced to produce observed nucleation rates in the lower troposphere. A simple and computationally efficient model for biogenic secondary organic aerosol (BSOA) formation was implemented. Here we study the sensitivity of the aerosol and cloud droplet number concentrations (CDNC) to these additions. Activation-type nucleation significantly increases aerosol number concentrations in the boundary layer. Increased particle number concentrations have a significant effect also on cloud droplet number concentrations and therefore on cloud properties. We performed calculations with activation nucleation coefficient values of 2×10-7s-1, 2×10-6s-1 and 2×10-5s-1 to evaluate the sensitivity to this parameter. For BSOA we have used yields of 0.025, 0.07 and 0.15 to estimate the amount of monoterpene oxidation products available for condensation. The hybrid BSOA formation scheme induces large regional changes to size distribution of organic carbon, and therefore affects particle optical properties and cloud droplet number concentrations locally. Although activation-type nucleation improves modeled aerosol number concentrations in the boundary layer, the use of a global activation coefficient generally leads to overestimation of aerosol number. Overestimation can also arise from underestimation of primary emissions.

  1. Characterization of a Quadrotor Unmanned Aircraft System for Aerosol-Particle-Concentration Measurements.

    PubMed

    Brady, James M; Stokes, M Dale; Bonnardel, Jim; Bertram, Timothy H

    2016-02-01

    High-spatial-resolution, near-surface vertical profiling of atmospheric chemical composition is currently limited by the availability of experimental platforms that can sample in constrained environments. As a result, measurements of near-surface gradients in trace gas and aerosol particle concentrations have been limited to studies conducted from fixed location towers or tethered balloons. Here, we explore the utility of a quadrotor unmanned aircraft system (UAS) as a sampling platform to measure vertical and horizontal concentration gradients of trace gases and aerosol particles at high spatial resolution (1 m) within the mixed layer (0-100 m). A 3D Robotics Iris+ autonomous quadrotor UAS was outfitted with a sensor package consisting of a two-channel aerosol optical particle counter and a CO2 sensor. The UAS demonstrated high precision in both vertical (±0.5 m) and horizontal positions (±1 m), highlighting the potential utility of quadrotor UAS drones for aerosol- and trace-gas measurements within complex terrain, such as the urban environment, forest canopies, and above difficult-to-access areas such as breaking surf. Vertical profiles of aerosol particle number concentrations, acquired from flights conducted along the California coastline, were used to constrain sea-spray aerosol-emission rates from coastal wave breaking. PMID:26730457

  2. Droplet Number Concentration Value-Added Product

    SciTech Connect

    Riihimaki, L.; McFarlane, S.; Sivaraman, C.

    2014-06-01

    The ndrop_mfrsr value-added product (VAP) provides an estimate of the cloud droplet number concentration of overcast water clouds retrieved from cloud optical depth from the multi-filter rotating shadowband radiometer (MFRSR) instrument and liquid water path (LWP) retrieved from the microwave radiometer (MWR). When cloud layer information is available from vertically pointing lidar and radars in the Active Remote Sensing of Clouds (ARSCL) product, the VAP also provides estimates of the adiabatic LWP and an adiabatic parameter (beta) that indicates how divergent the LWP is from the adiabatic case. quality control (QC) flags (qc_drop_number_conc), an uncertainty estimate (drop_number_conc_toterr), and a cloud layer type flag (cloud_base_type) are useful indicators of the quality and accuracy of any given value of the retrieval. Examples of these major input and output variables are given in sample plots in section 6.0.

  3. Process evaluation of sea salt aerosol concentrations at remote marine locations

    NASA Astrophysics Data System (ADS)

    Struthers, H.; Ekman, A. M.; Nilsson, E. D.

    2011-12-01

    Sea salt, an important natural aerosol, is generated by bubbles bursting at the surface of the ocean. Sea salt aerosol contributes significantly to the global aerosol burden and radiative budget and are a significant source of cloud condensation nuclei in remote marine areas (Monahan et al., 1986). Consequently, changes in marine aerosol abundance is expected to impact on climate forcing. Estimates of the atmospheric burden of sea salt aerosol mass derived from chemical transport and global climate models vary greatly both in the global total and the spatial distribution (Texor et al. 2006). This large uncertainty in the sea salt aerosol distribution in turn contributes to the large uncertainty in the current estimates of anthropogenic aerosol climate forcing (IPCC, 2007). To correctly attribute anthropogenic climate change and to veraciously project future climate, natural aerosols including sea salt must be understood and accurately modelled. In addition, the physical processes that determine the sea salt aerosol concentration are susceptible to modification due to climate change (Carslaw et al., 2010) which means there is the potential for feedbacks within the climate/aerosol system. Given the large uncertainties in sea salt aerosol modelling, there is an urgent need to evaluate the process description of sea salt aerosols in global models. An extremely valuable source of data for model evaluation is the long term measurements of PM10 sea salt aerosol mass available from a number of remote marine observation sites around the globe (including the GAW network). Sea salt aerosol concentrations at remote marine locations depend strongly on the surface exchange (emission and deposition) as well as entrainment or detrainment to the free troposphere. This suggests that the key parameters to consider in any analysis include the sea surface water temperature, wind speed, precipitation rate and the atmospheric stability. In this study, the sea salt aerosol observations

  4. The effect of anthropogenic sulfate aerosols on marine cloud droplet concentrations

    NASA Astrophysics Data System (ADS)

    Novakov, T.; Rivera-Carpio, C.; Penner, J. E.; Rogers, C. F.

    1994-04-01

    Nonseasalt sulfate (nss SO42-) mass concentrations, cloud condensation nuclei (CCN) number concentrations, and cloud droplet concentrations in warm cumulus and stratocumulus clouds were simultaneously measured in situ in marine air masses on El Yunque peak in Puerto Rico. Our results show that CNN number concentrations (measured at 0.5% supersaturation) and nss SO42- mass concentrations (in the range of ˜ 400 1700ng m-342- mass concentrations (in the range of ˜ 300 1400ng m-3). In stratocumulus clouds, a small increase in droplet concentration with nss SO42- mass concentrations in the range of ˜ 300 1100ng m-3 was observed. We attribute the low sensitivities of the droplet number concentrations to nss SO42- mass concentrations to the entrainment/mixing processes in these clouds. The magnitudes of the empirically derived sensitivities are considerably lower than those assumed in recent assessments of the effect of anthropogenic sulfate aerosols on cloud albedo.

  5. Factors controlling the CCN number concentrations at north of East China Sea in spring 2005

    NASA Astrophysics Data System (ADS)

    Koike, M.; Kuwata, M.; Kondo, Y.; Miyazaki, Y.; Kodama, D.; Yum, S. S.; Tanimoto, H.; Matsueda, H.

    2006-12-01

    Ground based measurement of Cloud Condensation Nuclei (CCN) was made at Gosan station on Jeju Island, Korea, which is located at north of East China Sea during the Atmospheric Brown Cloud/East Asian Regional Experiment 2005 (ABC/EAREX2005) campaign conducted in March/April 2005. An averaged CCN number concentration was 3600 cm-3 at super-saturation S = 1.0%, which is higher than previously-reported CCN concentrations in the maritime (less than 1000 cm-3) and continental (about 2000 cm-3) air, and is as high as the CCN concentration measured in air influenced by large- scale biomass burning in southern Africa and Amazon. When air parcels which had been strongly affected by anthropogenic emissions over Asian continent were transported, CCN concentrations increased by a factor of 2-6. While the CCN concentrations at S = 1.0 and 0.6% are primarily explained by the temporal change in aerosol total number concentrations, the aerosol size distribution becomes more important for the CCN concentration at S = 0.3 and 0.1%. For S = 1.0%, in addition to transport of anthropogenic aerosols from over the Asian continent, the new particle formation resulted from anthropogenic precursor gases and their subsequent growth are likely important to increase CCN number concentrations. For S = 0.1%, CCN number concentration generally correlated with CO concentration, and more than 80% of these aerosols contained refractory-core, suggesting that many of these CCN had been transported from over the Asian continent. These aerosols are considered to grow to the critical dry diameter of 130 nm through condensation of precursor gases and/or coagulation of aerosols.

  6. Aerosol and CCN Concentrations under Extremely High DMS Levels over the North Atlantic Ocean

    NASA Astrophysics Data System (ADS)

    Deng, C.; Brooks, S. D.; Thornton, D. C.; Bell, T. G.; Saltzman, E. S.; De Bruyn, W. J.

    2013-12-01

    throughout this cruise. In addition the extent to which DMS is oxidized by NO3 radical in nighttime is estimated to be more than 50% of that by OH and halogen during daytime over the North Atlantic Ocean area based on our data. Even though continental sources increase the total aerosol concentrations, it could depress the effective CCN concentrations, since pollution particles include soot and dust which are poor CCN. In addition, we found that the aerosol number concentration is correlated with sea surface pressure, which suggests that nucleation mode aerosol concentration is much higher in the free troposphere than in the MBL. The negative correlations between marine CCN or aerosol concentration and wind speed reported by others may therefore be interpreted by the inherent inverse correlation between pressure and wind speed. Our data also corroborates previous findings that chlorophyll a, a proxy of phytoplankton biomass, can only serve as a coarse indicator for DMS production, and in turn would be less indicative for marine aerosol, due to all the nonlinear processes involved in the phytoplankton-DMS-aerosol interactions.

  7. Variation of particle number concentration and size distributions at the urban environment in Vilnius (Lithuania)

    NASA Astrophysics Data System (ADS)

    Ulevicius, Vidmantas; Byčenkienë, Steigvilë; Plauškaitë, Kristina; Dudoitis, Vadimas

    2013-05-01

    This study presents results of research on urban aerosol particles with a focus on the particle size distribution and the aerosol particle number concentration (PNC). The real time measurements of the aerosol PNC in the size range of 9-840 nm were performed at the urban background site using a Condensed Particle Counter and Scanning Mobility Particle Sizer (SMPS). Strong diurnal patterns in aerosol PNC were evident as a direct effect of three sources of the aerosol particles (nucleation, traffic, and residential heating appliances). The traffic exhaust emissions were a major contributor of the pollution observed at the roadside site that was dominated by the nucleation mode particles, while particles formed due to the residential heating appliances and secondary formation processes contributed to the accumulation mode particles and could impact the variation of PNC and its size distribution during the same day.

  8. Vertical profiles of black carbon concentration and particle number size distribution in the North China Plain

    NASA Astrophysics Data System (ADS)

    Ran, L.; Deng, Z.

    2013-12-01

    The vertical distribution of aerosols is of great importance to our understanding in the impacts of aerosols on radiation balance and climate, as well as air quality and public health. To better understand and estimate the effects of atmospheric components including trace gases and aerosols on atmospheric environment and climate, an intensive field campaign, Vertical Observations of trace Gases and Aerosols in the North China Plain (VOGA-NCP), was carried out from late July to early August 2013 over a rural site in the polluted NCP. During the campaign, vertical profiles of black carbon (BC) concentration and particle number size distribution were measured respectively by a micro-Aethalometer and an optical particle counter attached to a tethered balloon within 1000 m height. Meteorological parameters, including temperature, relative humidity, wind speed and wind direction, were measured simultaneously by a radiosonde also attached to the tethered balloon. Preliminary results showed distinct diurnal variations of the vertical distribution of aerosol total number concentration and BC concentration, following the development of the mixing layer. Generally, there was a well mixing of aerosols within the mixing layer and a sharp decrease above the mixing layer. Particularly, a small peak of BC concentrations was observed around 400-500 m height for several profiles. Further analysis would be needed to explain such phenomenon. It was also found that measured vertical profiles of BC using the filter-based method might be affected by the vertical distribution of relative humidity.

  9. CCN Study at Urban Supersite (T0) During MILAGRO: the Essential Information for Prediction of Aerosol CCN Concentrations

    NASA Astrophysics Data System (ADS)

    Wang, J.; Cubison, M.; Aiken, A. C.; Jimenez, J. L.; Collins, D. R.

    2009-12-01

    The influences of atmospheric aerosols on cloud properties (i.e., aerosol indirect effects) strongly depend on the aerosol CCN concentrations, which can be effectively predicted from detailed aerosol size distribution, mixing state, and chemical composition using Köhler theory. However, atmospheric aerosols often consist of a large number of species that cannot be individually simulated in global or regional models due to computational constraints. Furthermore, the thermodynamic properties or even the molecular identities of many organic species present in ambient aerosols are often not known to predict their cloud-activation behavior using Köhler theory. As a result, simplified presentations of aerosol composition are necessary for large-scale models. In this study, aerosol microphysics, CCN concentrations, and chemical composition measured at the T0 urban supersite in Mexico City during MILAGRO are analyzed and the degree of closure is evaluated. During the campaign in March 2006, aerosol size distribution and composition often showed strong diurnal variation as a result of both primary emissions and aging of aerosols through coagulation and local photochemical production of secondary aerosol species. The submicron aerosol composition was ~1/2 organic species. Closure analysis is first carried out by comparing CCN concentrations calculated from the measured aerosol size distribution, mixing state, and chemical composition using extended Köhler theory to concurrent CCN measurements at five supersaturations ranging from 0.11% to 0.35%. The closure agreement and its diurnal variation are studied. CCN concentrations are also derived using various simplifications of the measured aerosol mixing state and chemical composition. The uncertainties associated with these simplifications are compared for different supersaturations and the variation of the uncertainties is examined as a function of aerosol age. The results show that the simplification of internally mixed

  10. Characterization of aerosol composition, concentrations, and sources at Baengnyeong Island, Korea using an aerosol mass spectrometer

    NASA Astrophysics Data System (ADS)

    Lee, Taehyoung; Choi, Jinsoo; Lee, Gangwoong; Ahn, Junyoung; Park, Jin Soo; Atwood, Samuel A.; Schurman, Misha; Choi, Yongjoo; Chung, Yoomi; Collett, Jeffrey L.

    2015-11-01

    To improve understanding of the sources and chemical properties of particulate pollutants on the western side of the Korean Peninsula, an Aerodyne High Resolution Time of Flight Aerosol Mass Spectrometer (HR-ToF-AMS) measured non-refractory fine (PM1) particles from May to November, 2011 at Baengnyeong Island, South Korea. Organic matter and sulfate were generally the most abundant species and exhibited maximum concentrations of 36 μg/m3 and 39 μg/m3, respectively. Nitrate concentrations peaked at 32 μg/m3 but were typically much lower than sulfate and organic matter concentrations. May, September, October, and November featured the highest monthly average concentrations, with lower concentrations typically observed from June through August. Potential source contribution function (PSCF) analysis and individual case studies revealed that transport from eastern China, an area with high SO2 emissions, was associated with high particulate sulfate concentrations at the measurement site. Observed sulfate aerosol sometimes was fully neutralized by ammonium but often was acidic; the average ammonium to sulfate molar ratio was 1.49. Measured species size distributions revealed a range of sulfate particle size distributions with modes between 100 and 600 nm. Organic aerosol source regions were widespread, including contributions from eastern China and South Korea. Positive matrix factorization (PMF) analysis indicated three "factors," or types of organic aerosol, comprising one primary, hydrocarbon-like organic aerosol (HOA) and two oxidized organic aerosol (OOA) components, including a more oxidized (MO-OOA) and a less oxidized (LO-OOA) oxidized organic aerosol. On average, HOA and OOA contributed 21% and 79% of the organic mass (OM), respectively, with the MO-OOA fraction nearly three times as abundant as the LO-OOA fraction. Biomass burning contributions to observed OM were low during the late spring/early summer agricultural burning season in eastern China, since

  11. Concentrations and size distributions of Antarctic stratospheric aerosols

    NASA Technical Reports Server (NTRS)

    Ferry, G. V.; Pueschel, R. F.; Neish, E.; Schultz, M.

    1989-01-01

    Particle Measuring Systems laser particle spectrometer (ASAS-X and FSSP) probes were used to measure aerosol particle concentrations and size distributions during 11 ER-2 flights between Punta Arenas (53 deg S) and Antarctica (up to 72 deg S) from August 17 to September 22, 1987. The time resolution was 10 s, corresponding to a spatial resolution of 2 km. The data were divided into two size classes (0.05-0.25 and 0.53-5.5 micron radius) to separate the small particle from the coarse particle populations. Results show that the small-particle concentrations are typical for a background aerosol during volcanic quiescence. This concentration is generally constant along a flight track; in only one instance a depletion of small particles during a polar stratospheric cloud (PSC) encounter was measured, suggesting a nucleation of type I PSC particles on background aerosols. Temporary increases of the coarse particle concentrations indicated the presence of tenuous polar stratospheric clouds that were encountered most frequently at the southernmost portion of a flight track and when the aircraft descended to lower altitudes. During 'particle events', particle modes were found at 0.6-micron radius, corresponding to type I PSCs, and occasionally, at 2.0-micron radius corresponding to type II PSCs.

  12. Relationship Between Aerosol Number Size Distribution and Atmospheric Electric Potential Gradient in an Urban Area

    NASA Astrophysics Data System (ADS)

    Wright, Matthew; Matthews, James; Bacak, Asan; Silva, Hugo; Priestley, Michael; Percival, Carl; Shallcross, Dudley

    2016-04-01

    Small ions are created in the atmosphere by ground based radioactive decay and solar and cosmic radiation ionising the air. The ionosphere is maintained at a high potential relative to the Earth due to global thunderstorm activity, a current from the ionosphere transfers charge back to the ground through the weakly ionised atmosphere. A potential gradient (PG) exists between the ionosphere and the ground that can be measured in fair weather using devices such as an electric field mill. PG is inversely-proportional to the conductivity of the air and therefore to the number of ions of a given electrical mobility; a reduction of air ions will cause an increase of PG. Aerosols in the atmosphere act as a sink of air ions with an attachment rate dependent on aerosol size distribution and ion mobility. These relationships have been used to infer high particulate, and hence pollution, levels in historic datasets of atmospheric PG. A measurement campaign was undertaken in Manchester, UK for three weeks in July and August where atmospheric PG was measured with an electric field mill (JCI131, JCI Chilworth) on a second floor balcony, aerosol size distribution measured with a scanning mobility particle sizer (SMPS, TSI3936), aerosol concentration measured with a condensation particle counter (CPC, Grimm 5.403) and local meteorological measurements taken on a rooftop measurement site ~200 m away. Field mill and CPC data were taken at 1 s intervals and SMPS data in 2.5 minute cycles. Data were excluded for one hour either side of rainfall as rainclouds and droplets can carry significant charge which would affect PG. A quantity relating to the attachment of ions to aerosol (Ion Sink) was derived from the effective attachment coefficient of the aerosols. Further measurements with the field mill and CPC were taken at the same location in November 2015 when bonfire events would be expected to increase aerosol concentrations. During the summer measurements, particle number count (PNC

  13. Urban background levels of particle number concentration and sources in Vilnius, Lithuania

    NASA Astrophysics Data System (ADS)

    Byčenkienė, Steigvilė; Plauškaitė, Kristina; Dudoitis, Vadimas; Ulevicius, Vidmantas

    2014-06-01

    This study presents results of research on urban aerosol particles with a focus on the aerosol particle number concentration (PNC) and the particle size distribution. The real time measurements of aerosol PNC (> 4.5 nm) and number size distributions (9-840 nm) were performed. The seasonal variations essentially comprised the minimum monthly mean in October 2010 (3400 ± 3000 cm- 3) and the maximum in April 2011 (19,000 ± 15,000 cm- 3). The mean annual PNC was 10,000 ± 8000 cm- 3 with an average mode size of 30-50 nm. The presence of strong diurnal patterns in aerosol PNC was evident as a direct effect of three sources of aerosol particles (nucleation, traffic, and residential heating). Hybrid receptor modeling potential source contribution function (PSCF) and concentration weighted trajectory (CWT) were used by incorporating 72-h backward trajectories and measurements of PNC in Vilnius. The results of trajectory clustering and the PSCF method demonstrated that possible additional source areas contributing to the elevated particle number concentration in Vilnius could be industrial areas in central Europe. Principal component analysis (PCA) revealed highest loadings for PNC, PM10, NOx, NO, NO2 and SO2 concentrations, indicating combustion processes occurring in vehicle engines and use of sulfur-containing fossil fuels for residential heating.

  14. Direct gravimetric determination of aerosol mass concentration in central antarctica.

    PubMed

    Annibaldi, Anna; Truzzi, Cristina; Illuminati, Silvia; Scarponi, Giuseppe

    2011-01-01

    In Antarctica, experimental difficulties due to extreme conditions have meant that aerosol mass has rarely been measured directly by gravimetry, and only in coastal areas where concentrations were in the range of 1-7 μg m(-3). The present work reports on a careful differential weighing methodology carried out for the first time on the plateau of central Antarctica (Dome C, East Antarctica). To solve problems of accurate aerosol mass measurements, a climatic room was used for conditioning and weighing filters. Measurements were carried out in long stages of several hours of readings with automatic recording of temperature/humidity and mass. This experimental scheme allowed us to sample from all the measurements (up to 2000) carried out before and after exposure, those which were recorded under the most stable humidity conditions and, even more importantly, as close to each other as possible. The automatic reading of the mass allowed us in any case to obtain hundreds of measurements from which to calculate average values with uncertainties sufficiently low to meet the requirements of the differential weighing procedure (±0.2 mg in filter weighing, between ±7% and ±16% both in aerosol mass and concentration measurements). The results show that the average summer aerosol mass concentration (aerodynamic size ≤10 μm) in central Antarctica is about 0.1 μg m(-3), i.e., about 1/10 of that of coastal Antarctic areas. The concentration increases by about 4-5 times at a site very close to the station. PMID:21141836

  15. Aerosol formation by ozonolysis of α- and β-pinene with initial concentrations below 1 ppb

    NASA Astrophysics Data System (ADS)

    Saathoff, Harald; Naumann, Karl-Heinz; Möhler, Ottmar

    2014-05-01

    Secondary organic aerosols (SOA) from the oxidation of biogenic volatile organic compounds (BVOC) are a large fraction of the tropospheric aerosol especially over tropical continental regions. The dominant SOA forming compounds are monoterpenes of which pinene is the most abundant. The reactions of monoterpenes with OH radicals, NO3 radicals, and ozone yield secondary organic aerosol mass in highly variable yields. Despite the various studies on SOA formation the influence of temperature and precursor concentrations on SOA yields are still major uncertainties in tropospheric aerosol models. In previous studies we observed a negative temperature dependence of SOA yields for SOA from ozonolysis α-pinene and limonene (Saathoff et al., 2009). However, this study as well as most of the literature data for measured SOA yields is limited to terpene concentrations of several ppb and higher (e.g. Bernard et al., 2012), hence about an order of magnitude higher than terpene concentrations even near their sources. Monoterpene concentrations in and above tropical or boral forests reach values up to a few tenth of a ppb during daytime decreasing rapidly with altitude in the boundary layer (Kesselmeier et al. 2000; Boy et al., 2004). Therefore we investigated the yield of SOA material from the ozonolysis of α- and β-pinene under simulated tropospheric conditions in the large aerosol chamber AIDA on time scales of several hours and for terpene concentrations between 0.1 and 1 ppb. The temperatures investigated were 243, 274, and 296 K with relative humidities ranging from 25% to 41%. The organic aerosol was generated by controlled oxidation with an excess of ozone (220-930 ppb) and the aerosol yield is calculated from size distributions measured with differential mobility analysers (SMPS, TSI, 3071 & 3080N) in the size range between 2 and 820 nm. On the basis of the measured initial particle size distribution, particle number concentration (CPC, TSI, 3775, 3776, 3022), and

  16. The impact of residential combustion emission on Arctic aerosol concentrations

    NASA Astrophysics Data System (ADS)

    Eckhardt, Sabine; Stohl, Andreas; Olivie, Dirk J. L.; Grini, Alf

    2016-04-01

    Arctic haze is a seasonal phenomenon with high concentrations of accumulation-mode aerosols occurring in the Arctic in winter and early spring. It has been challenging to reproduced this cylce and concentration levels with atmospheric transport and climate models. However, simulations have been improving recently and it has been shown, that a better scavenging parametrization as well as more realistic emissions are important to obtain better results. In this study we focus on the emission from residential heating, which depend on air temperature, as heating demand is higher on cold days. Varying this emission shows a clear effect on modeled Arctic concentrations. Arctic-mean and annual-mean concentrations of black carbon from Arctic domestic combustion emissions due to heating requirements, are nearly 70% higher when accounting for diurnal emission variability relative to constant emissions (Stohl et al., 2013). Emissions are high when ambient temperatures are low and cold air is transported to the Arctic. In order to capture this systematic effect, we created an interactive emission module for NorESM, a climate model, using the heating degree-day concept. Domestic combustion emissions of BC and other species are scaled interactively with the modeled ambient air temperatures, while securing that levels of annual total emissions from emission scenarios are reproduced. We compare the modeled aerosol concentration in the Arctic to observations and show the level of improvements achieved by using varying emission.

  17. Concentrations, size distributions and temporal variations of fluorescent biological aerosol particles in southern tropical India

    NASA Astrophysics Data System (ADS)

    Valsan, Aswathy; Krishna R, Ravi; CV, Biju; Huffman, Alex; Poschl, Ulrich; Gunthe, Sachin

    2015-04-01

    Biological aerosols constitute a wide range of dead and alive biological materials and structures that are suspended in the atmosphere. They play an important role in the atmospheric physical, chemical and biological processes and health of living being by spread of diseases among humans, plants, and, animals. The atmospheric abundance, sources, physical properties of PBAPs as compared to non-biological aerosols, however, is poorly characterized. The Indian tropical region, where large fraction of the world's total population is residing, experiences a distinctive meteorological phenomenon by means of Indian Summer Monsoon (IMS). Thus, the properties and characteristics of biological aerosols are also expected to be very diverse over the Indian subcontinent depending upon the seasons. Here we characterize the number concentration and size distribution of Fluorescent Biological Aerosol Particles (FBAP) at a high altitude continental site, Munnar (10.09 N, 77.06 E; 1605 m asl) in South India during the South-West monsoon, which constitute around 80 percent of the annual rainfall in Munnar. Continuous three months measurements (from 01 June 2014 to 21 Aug 2104) FBAPs were carried out at Munnar using Ultra Violet Aerodynamic Particle Sizer (UVAPS) during IMS. The mean number and mass concentration of coarse FBAP averaged over the entire campaign was 1.7 x 10-2 cm-3 and 0.24 µg m-3 respectively, which corresponds to 2 percent and 6 percent of total aerosol particle number and mass concentration. In agreement to other previous measurements the number size distribution of FBAP also peaks at 3.2 micron indicating the strong presence of fungal spores. This was also supported by the Scanning Electron Microscopic analysis of bioaerosols on filter paper. They also displayed a strong diurnal cycle with maximum concentration occurring at early morning hours. During periods of heavy and continuous rain where the wind is consistently blowing from South-West direction it was

  18. Black Carbon Concentration from Worldwide Aerosol Robotic Network (AERONET)

    NASA Technical Reports Server (NTRS)

    Schuster, Greg; Dubovik, Oleg; Holben, Brent; Clothiaux, Eugene

    2008-01-01

    Worldwide black carbon concentration measurements are needed to assess the efficacy of the carbon emissions inventory and transport model output. This requires long-term measurements in many regions, as model success in one region or season does not apply to all regions and seasons. AERONET is an automated network of more than 180 surface radiometers located throughout the world. The sky radiance measurements obtained by AERONET are inverted to provide column-averaged aerosol refractive indices and size distributions for the AERONET database, which we use to derive column-averaged black carbon concentrations and specific absorptions that are constrained by the measured radiation field. This provides a link between AERONET sky radiance measurements and the elemental carbon concentration of transport models without the need for an optics module in the transport model. Knowledge of both the black carbon concentration and aerosol absorption optical depth (i.e., input and output of the optics module) will enable improvements to the transport model optics module.

  19. Aerosol concentration and size distribution measured below, in, and above cloud from the DOE G-1 during VOCALS-REx

    SciTech Connect

    Kleinman L. I.; Daum, P. H.; Lee, Y.-N.; Lewis, E. R.; Sedlacek III, A. J.; Senum, G. I.; Springston, S. R.; Wang, J.; Hubbe, J.; Jayne, J.; Min, Q.; Yum, S. S.; Allen, G.

    2012-01-04

    During the VOCALS Regional Experiment, the DOE G-1 aircraft was used to sample a varying aerosol environment pertinent to properties of stratocumulus clouds over a longitude band extending 800 km west from the Chilean coast at Arica. Trace gas and aerosol measurements are presented as a function of longitude, altitude, and dew point in this study. Spatial distributions are consistent with an upper atmospheric source for O{sub 3} and South American coastal sources for marine boundary layer (MBL) CO and aerosol, most of which is acidic sulfate. Pollutant layers in the free troposphere (FT) can be a result of emissions to the north in Peru or long range transport from the west. At a given altitude in the FT (up to 3 km), dew point varies by 40 C with dry air descending from the upper atmospheric and moist air having a boundary layer (BL) contribution. Ascent of BL air to a cold high altitude results in the condensation and precipitation removal of all but a few percent of BL water along with aerosol that served as CCN. Thus, aerosol volume decreases with dew point in the FT. Aerosol size spectra have a bimodal structure in the MBL and an intermediate diameter unimodal distribution in the FT. Comparing cloud droplet number concentration (CDNC) and pre-cloud aerosol (D{sub p} > 100 nm) gives a linear relation up to a number concentration of {approx}150 cm{sup -3}, followed by a less than proportional increase in CDNC at higher aerosol number concentration. A number balance between below cloud aerosol and cloud droplets indicates that {approx}25 % of aerosol with D{sub p} > 100 nm are interstitial (not activated). A direct comparison of pre-cloud and in-cloud aerosol yields a higher estimate. Artifacts in the measurement of interstitial aerosol due to droplet shatter and evaporation are discussed. Within each of 102 constant altitude cloud transects, CDNC and interstitial aerosol were anti-correlated. An examination of one cloud as a case study shows that the

  20. Number size distribution measurements of biological aerosols under contrasting environments and seasons from southern tropical India

    NASA Astrophysics Data System (ADS)

    Valsan, Aswathy; Cv, Biju; Krishna, Ravi; Huffman, Alex; Poschl, Ulrich; Gunthe, Sachin

    2016-04-01

    Biological aerosols constitute a wide range of dead and alive biological materials and structures that are suspended in the atmosphere. They play an important role in the atmospheric physical, chemical and biological processes and health of living being by spread of diseases among humans, plants, and, animals. The atmospheric abundance, sources, physical properties of PBAPs as compared to non-biological aerosols, however, is poorly characterized. Though omnipresent, their concentration and composition exhibit large spatial and temporal variations depending up on their sources, land-use, and local meteorology. The Indian tropical region, which constitutes approximately 18% of the world's total population exhibits vast geographical extend and experiences a distinctive meteorological phenomenon by means of Indian Summer Monsoon (IMS). Thus, the sources, properties and characteristics of biological aerosols are also expected to have significant variations over the Indian subcontinent depending upon the location and seasons. Here we present the number concentration and size distribution of Fluorescent Biological Aerosol Particles (FBAP) from two contrasting locations in Southern tropical India measured during contrasting seasons using Ultra Violet Aerodynamic Particle Sizer (UV-APS). Measurements were carried out at a pristine high altitude continental site, Munnar (10.09 N, 77.06 E; 1605 m asl) during two contrasting seasons, South-West Monsoon (June-August, 2014) and winter (Jan - Feb, 2015) and in Chennai, a coastal urban area, during July - November 2015. FBAP concentrations at both the locations showed large variability with higher concentrations occurring at Chennai. Apart from regional variations, the FBAP concentrations also exhibited variations over two different seasons under the same environmental condition. In Munnar the FBAP concentration increased by a factor of four from South-West Monsoon to winter season. The average size distribution of FBAP at both

  1. Aerosol formation from high-velocity uranium drops: Comparison of number and mass distributions. Final report

    SciTech Connect

    Rader, D.J.; Benson, D.A.

    1995-05-01

    This report presents the results of an experimental study of the aerosol produced by the combustion of high-velocity molten-uranium droplets produced by the simultaneous heating and electromagnetic launch of uranium wires. These tests are intended to simulate the reduction of high-velocity fragments into aerosol in high-explosive detonations or reactor accidents involving nuclear materials. As reported earlier, the resulting aerosol consists mainly of web-like chain agglomerates. A condensation nucleus counter was used to investigate the decay of the total particle concentration due to coagulation and losses. Number size distributions based on mobility equivalent diameter obtained soon after launch with a Differential Mobility Particle Sizer showed lognormal distributions with an initial count median diameter (CMD) of 0.3 {mu}m and a geometric standard deviation, {sigma}{sub g} of about 2; the CMD was found to increase and {sigma}{sub g} decrease with time due to coagulation. Mass size distributions based on aerodynamic diameter were obtained for the first time with a Microorifice Uniform Deposit Impactor, which showed lognormal distributions with mass median aerodynamic diameters of about 0.5 {mu}m and an aerodynamic geometric standard deviation of about 2. Approximate methods for converting between number and mass distributions and between mobility and aerodynamic equivalent diameters are presented.

  2. Physicochemical characterization of Capstone depleted uranium aerosols I: uranium concentration in aerosols as a function of time and particle size.

    PubMed

    Parkhurst, Mary Ann; Cheng, Yung Sung; Kenoyer, Judson L; Traub, Richard J

    2009-03-01

    During the Capstone Depleted Uranium (DU) Aerosol Study, aerosols containing DU were produced inside unventilated armored vehicles (i.e., Abrams tanks and Bradley Fighting Vehicles) by perforation with large-caliber DU penetrators. These aerosols were collected and characterized, and the data were subsequently used to assess human health risks to personnel exposed to DU aerosols. The DU content of each aerosol sample was first quantified by radioanalytical methods, and selected samples, primarily those from the cyclone separator grit chambers, were analyzed radiochemically. Deposition occurred inside the vehicles as particles settled on interior surfaces. Settling rates of uranium from the aerosols were evaluated using filter cassette samples that collected aerosol as total mass over eight sequential time intervals. A moving filter was used to collect aerosol samples over time, particularly within the first minute after a shot. The results demonstrate that the peak uranium concentration in the aerosol occurred in the first 10 s after perforation, and the concentration decreased in the Abrams tank shots to about 50% within 1 min and to less than 2% after 30 min. The initial and maximum uranium concentrations were lower in the Bradley vehicle than those observed in the Abrams tank, and the concentration levels decreased more slowly. Uranium mass concentrations in the aerosols as a function of particle size were evaluated using samples collected in a cyclone sampler, which collected aerosol continuously for 2 h after perforation. The percentages of uranium mass in the cyclone separator stages ranged from 38 to 72% for the Abrams tank with conventional armor. In most cases, it varied with particle size, typically with less uranium associated with the smaller particle sizes. Neither the Abrams tank with DU armor nor the Bradley vehicle results were specifically correlated with particle size and can best be represented by their average uranium mass concentrations of 65

  3. Continuous emission monitoring of metal aerosol concentrations in atmospheric air

    NASA Astrophysics Data System (ADS)

    Gomes, Anne-Marie; Sarrette, Jean-Philippe; Madon, Lydie; Almi, Abdenbi

    1996-11-01

    Improvements of an apparatus for continuous emission monitoring (CEM) by inductively coupled plasma atomic emission spectrometry (ICP-AES) of metal aerosols in air are described. The method simultaneously offers low operating costs, large volume of tested air for valuable sampling and avoids supplementary contamination or keeping of the air pollutant concentrations. Questions related to detection and calibration are discussed. The detection limits (DL) obtained for the eight pollutants studied are lower than the recommended threshold limit values (TLV) and as satisfactory as the results obtained with other CEM methods involving air-argon plasmas.

  4. Relationships among particle number, surface area, and respirable mass concentrations in automotive engine manufacturing.

    PubMed

    Heitbrink, William A; Evans, Douglas E; Ku, Bon Ki; Maynard, Andrew D; Slavin, Thomas J; Peters, Thomas M

    2009-01-01

    This study investigated the relationships between particle number, surface area, and respirable mass concentration measured simultaneously in a foundry and an automotive engine machining and assembly center. Aerosol concentrations were measured throughout each plant with a condensation particle counter for number concentration, a diffusion charger for active surface area concentration, and an optical particle counter for respirable mass concentration. At selected locations, particle size distributions were characterized with the optical particle counter and an electrical low pressure impactor. Statistical analyses showed that active surface area concentration was correlated with ultrafine particle number concentration and weakly correlated with respirable mass concentration. Correlation between number and active surface area concentration was stronger during winter (R2 = 0.6 for both plants) than in the summer (R2 = 0.38 and 0.36 for the foundry and engine plant respectively). The stronger correlation in winter was attributed to use of direct-fire gas fired heaters that produced substantial numbers of ultrafine particles with a modal diameter between 0.007 and 0.023 mu m. These correlations support findings obtained through theoretical analysis. Such analysis predicts that active surface area increasingly underestimates geometric surface area with increasing particle size, particularly for particles larger than 100 nm. Thus, a stronger correlation between particle number concentration and active surface area concentration is expected in the presence of high concentrations of ultrafine particles. In general, active surface area concentration may be a concentration metric that is distinct from particle number concentration and respirable mass concentration. For future health effects or toxicological studies involving nano-materials or ultrafine aerosols, this finding needs to be considered, as exposure metrics may influence data interpretation. PMID:18982535

  5. Source apportionment of ambient particle number concentrations in central Los Angeles using positive matrix factorization (PMF)

    NASA Astrophysics Data System (ADS)

    Sowlat, Mohammad Hossein; Hasheminassab, Sina; Sioutas, Constantinos

    2016-04-01

    In this study, the positive matrix factorization (PMF) receptor model (version 5.0) was used to identify and quantify major sources contributing to particulate matter (PM) number concentrations, using PM number size distributions in the range of 13 nm to 10 µm combined with several auxiliary variables, including black carbon (BC), elemental and organic carbon (EC/OC), PM mass concentrations, gaseous pollutants, meteorological, and traffic counts data, collected for about 9 months between August 2014 and 2015 in central Los Angeles, CA. Several parameters, including particle number and volume size distribution profiles, profiles of auxiliary variables, contributions of different factors in different seasons to the total number concentrations, diurnal variations of each of the resolved factors in the cold and warm phases, weekday/weekend analysis for each of the resolved factors, and correlation between auxiliary variables and the relative contribution of each of the resolved factors, were used to identify PM sources. A six-factor solution was identified as the optimum for the aforementioned input data. The resolved factors comprised nucleation, traffic 1, traffic 2 (with a larger mode diameter than traffic 1 factor), urban background aerosol, secondary aerosol, and soil/road dust. Traffic sources (1 and 2) were the major contributor to PM number concentrations, collectively making up to above 60 % (60.8-68.4 %) of the total number concentrations during the study period. Their contribution was also significantly higher in the cold phase compared to the warm phase. Nucleation was another major factor significantly contributing to the total number concentrations (an overall contribution of 17 %, ranging from 11.7 to 24 %), with a larger contribution during the warm phase than in the cold phase. The other identified factors were urban background aerosol, secondary aerosol, and soil/road dust, with relative contributions of approximately 12 % (7.4-17.1), 2.1 % (1

  6. Aerosol concentration and size distribution measured below, in, and above cloud from the DOE G-1 during VOCALS-REx

    SciTech Connect

    Kleinman, L.I.; Daum, P. H.; Lee, Y.-N.; Lewis, E. R.; Sedlacek III, A. J.; Senum, G. I.; Springston, S. R.; Wang, J.; Hubbe, J.; Jayne, J.; Min, Q.; Yum, S. S.; Allen, G.

    2011-06-21

    During the VOCALS Regional Experiment, the DOE G-1 aircraft was used to sample a varying aerosol environment pertinent to properties of stratocumulus clouds over a longitude band extending 800 km west from the Chilean coast at Arica. Trace gas and aerosol measurements are presented as a function of longitude, altitude, and dew point in this study. Spatial distributions are consistent with an upper atmospheric source for O{sub 3} and South American coastal sources for marine boundary layer (MBL) CO and aerosol, most of which is acidic sulfate in agreement with the dominant pollution source being SO{sub 2} from Cu smelters and power plants. Pollutant layers in the free troposphere (FT) can be a result of emissions to the north in Peru or long range transport from the west. At a given altitude in the FT (up to 3 km), dew point varies by 40 C with dry air descending from the upper atmospheric and moist air having a BL contribution. Ascent of BL air to a cold high altitude results in the condensation and precipitation removal of all but a few percent of BL water along with aerosol that served as CCN. Thus, aerosol volume decreases with dew point in the FT. Aerosol size spectra have a bimodal structure in the MBL and an intermediate diameter unimodal distribution in the FT. Comparing cloud droplet number concentration (CDNC) and pre-cloud aerosol (Dp > 100 nm) gives a linear relation up to a number concentration of {approx}150 cm{sup -3}, followed by a less than proportional increase in CDNC at higher aerosol number concentration. A number balance between below cloud aerosol and cloud droplets indicates that {approx}25% of aerosol in the PCASP size range are interstitial (not activated). One hundred and two constant altitude cloud transects were identified and used to determine properties of interstitial aerosol. One transect is examined in detail as a case study. Approximately 25 to 50% of aerosol with D{sub p} > 110 nm were not activated, the difference between the two

  7. Aerosol concentration and size distribution measured below, in, and above cloud from the DOE G-1 during VOCALS-REx

    NASA Astrophysics Data System (ADS)

    Kleinman, L. I.; Daum, P. H.; Lee, Y.-N.; Lewis, E. R.; Sedlacek, A. J., III; Senum, G. I.; Springston, S. R.; Wang, J.; Hubbe, J.; Jayne, J.; Min, Q.; Yum, S. S.; Allen, G.

    2011-06-01

    During the VOCALS Regional Experiment, the DOE G-1 aircraft was used to sample a varying aerosol environment pertinent to properties of stratocumulus clouds over a longitude band extending 800 km west from the Chilean coast at Arica. Trace gas and aerosol measurements are presented as a function of longitude, altitude, and dew point in this study. Spatial distributions are consistent with an upper atmospheric source for O3 and South American coastal sources for marine boundary layer (MBL) CO and aerosol, most of which is acidic sulfate in agreement with the dominant pollution source being SO2 from Cu smelters and power plants. Pollutant layers in the free troposphere (FT) can be a result of emissions to the north in Peru or long range transport from the west. At a given altitude in the FT (up to 3 km), dew point varies by 40 °C with dry air descending from the upper atmospheric and moist air having a BL contribution. Ascent of BL air to a cold high altitude results in the condensation and precipitation removal of all but a few percent of BL water along with aerosol that served as CCN. Thus, aerosol volume decreases with dew point in the FT. Aerosol size spectra have a bimodal structure in the MBL and an intermediate diameter unimodal distribution in the FT. Comparing cloud droplet number concentration (CDNC) and pre-cloud aerosol (Dp > 100 nm) gives a linear relation up to a number concentration of ~150 cm-3, followed by a less than proportional increase in CDNC at higher aerosol number concentration. A number balance between below cloud aerosol and cloud droplets indicates that ~25 % of aerosol in the PCASP size range are interstitial (not activated). One hundred and two constant altitude cloud transects were identified and used to determine properties of interstitial aerosol. One transect is examined in detail as a case study. Approximately 25 to 50 % of aerosol with Dp > 110 nm were not activated, the difference between the two approaches possibly representing

  8. Predicting Cloud Droplet Number Concentration in Community Atmosphere Model (CAM)-Oslo

    SciTech Connect

    Storelvmo, Trude; Kristjansson, J. E.; Ghan, Steven J.; Kirkevag, A.; Seland, O.; Iversen, T.

    2006-12-22

    A continuity equation for cloud droplet number concentration is implemented in an extended version of the National Center for Atmospheric Research (NCAR) Community Atmosphere Model version 2.0.1 (CAM-2.0.1). The new continuity equation for cloud droplet number concentration consists of a nucleation term and several microphysical sink terms. The nucleation term is calculated based on a parameterization of activation of cloud condensation nuclei. A sub-grid distribution of vertical velocity is used to determine the range of supersaturations found within each model grid box. This supersaturation combined with the hygroscopicity of the aerosols present will determine the number of Cloud Condensation Nuclei (CCN) activated into cloud droplets. The aerosol types considered in this study are sea salt, sulfate, black carbon, organic carbon and mineral dust. The horizontal and vertical distributions of sulfate and carbonaceous aerosols are calculated based on AEROCOM (http://nansen.ipsl.jussieu.fr/AEROCOM) sources. These are combined with the background aerosols, which are a combination of sea salt, mineral dust and sulfate dependent on soil type, wind speed and location (Arctic, Antarctic, maritime, desert or continental). The resulting aerosol size distributions are multimodal, allowing sulfate, black carbon and organic carbon to be both internally and externally mixed with the background aerosols. Microphysical sink terms for cloud droplets are obtained from a prognostic cloud water scheme, assuming a direct proportionality between loss of cloud water and loss of cloud droplets. Based on the framework described above, the cloud droplet number concentration and cloud droplet effective radius can be determined. The resulting cloud radiative forcings (CRF) can hereafter be calculated. By comparing the CRF for two different model runs, one with pre-industrial aerosol sources and the other with sources corresponding to present day, the indirect effect of aerosols can be

  9. Capstone depleted uranium aerosol biokinetics, concentrations, and doses.

    PubMed

    Guilmette, Raymond A; Miller, Guthrie; Parkhurst, Mary Ann

    2009-03-01

    One of the principal goals of the Capstone Depleted Uranium (DU) Aerosol Study was to quantify and characterize DU aerosols generated inside armored vehicles by perforation with a DU penetrator. This study consequently produced a database in which the DU aerosol source terms were specified both physically and chemically for a variety of penetrator-impact geometries and conditions. These source terms were used to calculate radiation doses and uranium concentrations for various scenarios as part of the Capstone Human Health Risk Assessment (HHRA). This paper describes the scenario-related biokinetics of uranium, and summarizes intakes, chemical concentrations to the organs, and E(50) and HT(50) for organs and tissues based on exposure scenarios for personnel in vehicles at the time of perforation as well as for first responders. For a given exposure scenario (duration time and breathing rates), the range of DU intakes among the target vehicles and shots was not large, about a factor of 10, with the lowest being for a ventilated operational Abrams tank and the highest being for an unventilated Abrams with DU penetrator perforating DU armor. The ranges of committed effective doses were more scenario-dependent than were intakes. For example, the largest range, a factor of 20, was shown for scenario A, a 1 min exposure, whereas, the range was only a factor of two for the first-responder scenario (E). In general, the committed effective doses were found to be in the tens of mSv. The risks ascribed to these doses are discussed separately. PMID:19204489

  10. Using high time resolution aerosol and number size distribution measurements to estimate atmospheric extinction.

    PubMed

    Malm, William C; McMeeking, Gavin R; Kreidenweis, Sonia M; Levin, Ezra; Carrico, Christian M; Day, Derek E; Collett, Jeffrey L; Lee, Taehyoung; Sullivan, Amy P; Raja, Suresh

    2009-09-01

    Rocky Mountain National Park is experiencing reduced visibility and changes in ecosystem function due to increasing levels of oxidized and reduced nitrogen. The Rocky Mountain Atmospheric Nitrogen and Sulfur (RoMANS) study was initiated to better understand the origins of sulfur and nitrogen species as well as the complex chemistry occurring during transport from source to receptor. As part of the study, a monitoring program was initiated for two 1-month time periods--one during the spring and the other during late summer/fall. The monitoring program included intensive high time resolution concentration measurements of aerosol number size distribution, inorganic anions, and cations, and 24-hr time resolution of PM2.5 and PM10 mass, sulfate, nitrate, carbon, and soil-related elements concentrations. These data are combined to estimate high time resolution concentrations of PM2.5 and PM10 aerosol mass and fine mass species estimates of ammoniated sulfate, nitrate, and organic and elemental carbon. Hour-by-hour extinction budgets are calculated by using these species concentration estimates and measurements of size distribution and assuming internal and external particle mixtures. Summer extinction was on average about 3 times higher than spring extinction. During spring months, sulfates, nitrates, carbon mass, and PM10 - PM2.5 mass contributed approximately equal amounts of extinction, whereas during the summer months, carbonaceous material extinction was 2-3 times higher than other species. PMID:19785272

  11. Effects of diesel exhaust aftertreatment devices on concentrations and size distribution of aerosols in underground mine air.

    PubMed

    Bugarski, Aleksandar D; Schnakenberg, George H; Hummer, Ion A; Cauda, Emanuele; Janisko, Samuel I; Patts, Larry D

    2009-09-01

    Three types of uncatalyzed diesel particulate filter (DPF) systems, three types of high-temperature disposable filter elements (DFEs), and one diesel oxidation catalytic converter (DOC) were evaluated in underground mine conditions for their effects on the concentrations and size distributions of diesel aerosols. Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. The DPF systems reduced total mass of aerosols in the mine air approximately 10-fold for light-load and 20-fold or more for high-load test conditions. The DFEs offered similar reductions in aerosol mass concentrations. The efficiency of the new DFEs significantly increased with accumulation of operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on performance of the filter element The effectiveness of DPFs and DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for both DPFs and DFEs when the engine was operated at high-load modes than at low-load modes. The effects of the DOC on mass and number concentrations of aerosols in mine air were relatively minor when compared to those of the DPF and DFE systems. PMID:19764243

  12. Physicochemical Characterization of Capstone Depleted Uranium Aerosols I: Uranium Concentration in Aerosols as a Function of Time and Particle Size

    SciTech Connect

    Parkhurst, MaryAnn; Cheng, Yung-Sung; Kenoyer, Judson L.; Traub, Richard J.

    2009-03-01

    During the Capstone Depleted Uranium (DU) Aerosol Study, aerosols containing depleted uranium were produced inside unventilated armored vehicles (i.e., Abrams tanks and Bradley Fighting Vehicles) by perforation with large-caliber DU penetrators. These aerosols were collected and characterized, and the data were subsequently used to assess human health risks to personnel exposed to DU aerosols. The DU content of each aerosol sample was first quantified by radioanalytical methods, and selected samples, primarily those from the cyclone separator grit chambers, were analyzed radiochemically. Deposition occurred inside the vehicles as particles settled on interior surfaces. Settling rates of uranium from the aerosols were evaluated using filter cassette samples that collected aerosol as total mass over eight sequential time intervals. A moving filter was used to collect aerosol samples over time particularly within the first minute after the shot. The results demonstrate that the peak uranium concentration in the aerosol occurred in the first 10 s, and the concentration decreased in the Abrams tank shots to about 50% within 1 min and to less than 2% 30 min after perforation. In the Bradley vehicle, the initial (and maximum) uranium concentration was lower than those observed in the Abrams tank and decreased more slowly. Uranium mass concentrations in the aerosols as a function of particle size were evaluated using samples collected in the cyclone samplers, which collected aerosol continuously for 2 h post perforation. The percentages of uranium mass in the cyclone separator stages from the Abrams tank tests ranged from 38% to 72% and, in most cases, varied with particle size, typically with less uranium associated with the smaller particle sizes. Results with the Bradley vehicle ranged from 18% to 29% and were not specifically correlated with particle size.

  13. Particle concentrations and number size distributions in the planetary boundary layer derived from airship based measurements

    NASA Astrophysics Data System (ADS)

    Tillmann, Ralf; Zhao, Defeng; Ehn, Mikael; Hofzumahaus, Andreas; Holland, Frank; Rohrer, Franz; Kiendler-Scharr, Astrid; Wahner, Andreas

    2014-05-01

    Atmospheric particles play a key role for regional and global climate due to their direct and indirect radiative forcing effects. The concentration and size of the particles are important variables to these effects. Within the continental planetary boundary layer (PBL) the particle number size distribution is influenced by meteorological parameters, local sinks and sources resulting in variable spatial distributions. However, measurements of particle number size distributions over a broad vertical range of the PBL are rare. The airship ZEPPELIN NT is an ideal platform to measure atmospheric aerosols on a regional scale within an altitude range up to 1000 m. For campaigns in the Netherlands, Northern Italy and South Finland in 2012 and 2013 the airship was deployed with a wide range of instruments, including measurements of different trace gases, short lived radicals, solar radiation, aerosols and meteorological parameters. Flights were carried out at different times of the day to investigate the influence of the diurnal evolution of the PBL on atmospheric trace gases and aerosols. During night and early morning hours the concentration and size distribution of atmospheric particles were found to be strongly influenced by the layered structure of the PBL, i.e. the nocturnal boundary layer and the residual layer. Within the residual layer particle concentrations stay relatively constant as this layer is decoupled from ground sources. The particles persist in the accumulation mode as expected for an aged aerosol. In the nocturnal boundary layer particle concentrations and size are more dynamic with higher concentrations than in the residual layer. A few hours after sunrise, the layered structure of the PBL intermixes. During daytime the PBL is well mixed and a negative concentration gradient with increasing height is observed. Several height profiles at different times of the day and at different locations in Europe were measured. The aerosol measurements will be

  14. Wide-range particle characterization and elemental concentration in Beijing aerosol during the 2013 Spring Festival.

    PubMed

    Jing, Hui; Li, Yu-Feng; Zhao, Jiating; Li, Bai; Sun, Jialong; Chen, Rui; Gao, Yuxi; Chen, Chunying

    2014-09-01

    The number and mass concentration, size distribution, and the concentration of 16 elements were studied in aerosol samples during the Spring Festival celebrations in 2013 in Beijing, China. Both the number and mass concentration increased sharply in a wide range from 10 nm to 10 μm during the firecrackers and fireworks activities. The prominent increase of the number concentration was in 50 nm-500 nm with a peak of 1.7 × 10(5)/cm(3) at 150 nm, which is 8 times higher than that after 1.5 h. The highest mass concentration was in 320-560 nm, which is 4 times higher than the control. K, Mg, Sr, Ba and Pb increased sharply during the firework activities in PM10. Although the aerosol emission from firework activities is a short-term air quality degradation event, there may be a substantial hazard arising from the chemical composition of the emitted particles. PMID:24975025

  15. Sensitivity of aerosol concentrations and cloud properties to nucleation and secondary organic distribution in ECHAM5-HAM global circulation model

    NASA Astrophysics Data System (ADS)

    Makkonen, R.; Asmi, A.; Korhonen, H.; Kokkola, H.; Järvenoja, S.; Räisänen, P.; Lehtinen, K. E. J.; Laaksonen, A.; Kerminen, V.-M.; Järvinen, H.; Lohmann, U.; Feichter, J.; Kulmala, M.

    2008-06-01

    The global aerosol-climate model ECHAM5-HAM was modified to improve the representation of new particle formation in the boundary layer. Activation-type nucleation mechanism was introduced to produce observed nucleation rates in lower troposphere. A simple and computationally efficient model for biogenic secondary organic aerosol (BSOA) formation was implemented. We studied the sensitivity of aerosol and cloud droplet number concentrations (CDNC) to these additions. Activation-type nucleation significantly increases aerosol number concentrations in the boundary layer. Increased particle number concentrations have a significant effect also on cloud droplet number concentrations and therefore on cloud properties. We performed calculations with activation nucleation coefficient values of 2×10-7 s-1, 2×10-6 s-1 and 2×10-5 s-1 to evaluate the sensitivity to this parameter. For BSOA we have used yields of 0.025, 0.07 and 0.15 to estimate the amount of monoterpene oxidation products available for condensation. The dynamic SOA scheme induces large regional changes to size distribution of organic carbon, and therefore affects particle optical properties and cloud droplet number concentrations locally. Comparison with satellite observation shows that activation-type nucleation significantly decreases the differences between observed and modeled values of cloud top CDNC.

  16. Five-years of atmospheric aerosol number size distribution measurements in Eastern Mediterranean

    NASA Astrophysics Data System (ADS)

    Kalivitis, Nikolaos; Kouvarakis, Giorgos; Bougiatioti, Aikaterini; Stavroulas, Iasonas; Wiedensohler, Alfred; Mihalopoulos, Nikolaos

    2014-05-01

    The first long term measurements of atmospheric particle size distributions from the Eastern Mediterranean region are reported. Atmospheric aerosol number size distributions have been measured at the environmental research station of University of Crete at Finokalia, Crete, Greece (35° 20' N, 25° 40' E, 250m a.s.l) on a continuous base since 2008. A custom built (TROPOS type) scanning mobility particle sizer (SMPS) is used covering size ranges from 8 to 900 nm. The system is humidity controlled so that relative humidity is kept below 40% most of the time. Throughout the measuring period the average number concentration of the particles in the studied size range was found to be 2354 ± 1332 cm-3 (median of 2098 cm-3). Maximum concentrations are observed during summer while minimum during winter, reflecting the effectiveness of the removal processes in the region. Clear annual circles are found for the number concentrations of nucleation, Aitken and accumulation mode particles. Nucleation mode is presenting different pattern from the other two modes, with the highest concentrations during winter (and March) and the lowest during summer. New particle formation events are more frequently observed during March and October. The number size distributions present different seasonal patterns. During summer, unimodal distributions centering on the lower end of the accumulation mode size range are dominant in our observations. The prevailing meteorology characterized by the Etesian winds (Meltemi) and the lack of precipitation along the trajectory results to the arrival of well mixed air masses at Finokalia, carrying aged aerosol mainly from central and Eastern Europe. Regarding the other seasons, the shape of the distributions is more variable and strongly dependent on the air mass history: When the air masses are of marine origin or precipitation has affected them, the size distributions are mainly bimodal (peaking both in Aitken and in Accumulation mode). These

  17. Climate Sensitivities due to Stratocumulus Cloud droplet number concentrations

    NASA Astrophysics Data System (ADS)

    Parkes, Ben; Stevens, Laura; Gadian, Alan; Lathman, John; Blyth, Alan

    2010-05-01

    Four experiments have been carried out using the Met Office Unified Model v6.1 (HadGEM1) to investigate the effects of albedo modification on the climate system as the amount of carbon dioxide in the atmosphere continues to rise. This work is designed to analyse and assess the "cloud whiteneing" method of geoengineering postulated in (Latham, 1990) and expanded upon by (Latham et al., 2008)(Salter et al., 2008) and (Rasch et al., 2009). Consideration will be given to the effect of the cloud modification on rainfall rates and global circulation patterns. Furthermore temperature changes in polar regions are investigated to assess the increase in polar sea ice coverage. The four experiments are a control, one with an increase in carbon dioxide by 1% per year and two potential geoengineering scenarios based on a climate with increasing carbon dioxide. The first geoengineering simulation consists of forcing clouds with a cloud droplet number concentration (CDNC) of N = 375 m-3 over three regions of low lying stratocumulus clouds. These regions are the West coasts of California, Peru and Namibia(Latham et al., 2008). The second geoenginnering simulation is based upon forcing all marine environments with a CDNC of N = 375 m-3. Starting conditions for the experiments were provided by the UK Met Office from the A1B simulation used in the 2007 Intergovernmental Panel on Climate Change report(IPCC, 2007). The geoengineering method proposed relies on the aerosol indirect effect(Twomey, 1977) and the second aerosol indirect(Albrecht, 1989) effects on clouds to increase their brightness and prolong their lifetime. The effects of a change in CDNC on a clean marine stratocumulus cloud can be investigated using data collected from the VOCALs field campaign which took place in the South Eastern Pacific in 2008. radiometry and in cloud data has been collected by several aircraft including the FAAM BAe-146 and the NCAR/NSF C-130(Allen & Abel, 2009). The albedo of the observed region

  18. Analysis of tropospheric aerosol number density for aerosols of 0.2- to 3-micrometers diameter: Central and northeastern Canada

    NASA Technical Reports Server (NTRS)

    Gregory, Gerald L.; Anderson, Bruce E.; Barrick, John D.; Hudgins, Charles H.; Bagwell, Donald R.; Blake, Donald R.

    1994-01-01

    NASA's Atmospheric Boundary Layer Experiment conducted during the summer of 1990 focused on the distribution of trace species in central and northeastern Canada (altitudes less than 6 km) and the importance of surface sources/sinks, local emissions, distant transport, tropospheric/stratospheric exchange. Aircraft flights were based from North Bay, Ontario, and Goose Bay, Labrador, Canada. As part of the aircraft measurements, aerosol number density (0.2- to 3-micrometers diameter) was measured using an optical laser technique. Results show that summertime aerosol budgets of central and northeastern Canada can be significantly impacted by the transport of pollutants from distant source regions. Biomass burning in Alaska and western and central Canada exerts major influences on regional aerosol budgets. Urban emissions transported from the U.S./Canadian border regions are also important. Aerosol enhancements (mixed layer and free troposphere) were most prevalent in air with carbon monoxide mixing ratios greater than 110 parts per billion by volume (ppbv). When data were grouped as to the source of the air (5-day back trajectories) either north or south of the polar jet, aerosol number density in the mixed layer showed a tendency to be enhanced for air south of the jet relative to north of the jet. However, this difference was not observed for measurements at the higher altitudes (4 to 6 km). For some flights, mixed layer aerosol number densities were greater than 100 higher than free-tropospheric values (3- to 6-km altitude). The majority of the observed mixed layer enhancement was associated with transport of effluent-rich air into the Canadian regions. Aerosol emissions from natural Canadian ecosystems were relatively small when compared to transport.

  19. Sudden changes in aerosol and gas concentrations in the central Arctic marine boundary layer: Causes and consequences

    NASA Astrophysics Data System (ADS)

    Bigg, E. Keith; Leck, Caroline; Nilsson, E. Douglas

    2001-12-01

    Measurements of aerosol number size distributions and concentrations of the precursor gases dimethyl sulfide, sulfur dioxide and ammonia were made within the pack ice region of the central Arctic Ocean during July and August 1996 from the icebreaker Oden. Changes in concentration, sometimes exceeding the entire seasonal variation, often occurred within an hour and attempts to find the reasons for them are described. Vertical profiles of aerosol concentration in Aitken and accumulation mode particles obtained on helicopter flights revealed intense concentration gradients in the lowest 1000 m. Those below 100 m were common. Concentrations of accumulation mode particles were usually greater near the surface than at 100 m. Four representative case studies for which vertical aerosol profiles were obtained are presented. Observations of rapid large changes in near-surface concentration of aerosols in different size ranges are compared with the vertical profiles, meteorological information, and acoustic or optical remote sensing to infer processes causing the changes. Comparison of simultaneous variations in aerosols and precursor gas concentrations are used to define the vertical profiles of the gases. It was found that dimethyl sulfide and ammonia concentrations usually must have been strongly depleted near the surface relative to concentrations at about 100 m. Sulfur dioxide profiles appeared to be more complex. Turbulence or vertical air motions initiated by atmospheric wave motions trapped within the stable boundary layer appeared to be directly responsible for many of the sudden concentration changes, through interaction with concentration gradients close to the surface. The presence of low-level jets also had direct or indirect influences on mixing in the lowest few hundred meters. The extent to which aerosols measured near the surface can determine the microphysics of central Arctic marine boundary layer clouds is examined.

  20. Spatial and temporal distributions of aerosol concentrations and depositions in Asia during the year 2010.

    PubMed

    Park, Soon-Ung; Lee, In-Hye; Joo, Seung Jin

    2016-01-15

    Aerosol Modeling System (AMS) that is consisted of the Asian Dust Aerosol Model2 (ADAM2) and the Community Multi-scale Air Quality (CMAQ) modeling system has been employed to document the spatial distributions of the monthly and the annual averaged concentration of both the Asian dust (AD) aerosol and the anthropogenic aerosol (AA), and their total depositions in the Asian region for the year 2010. It is found that the annual mean surface aerosol (PM10) concentrations in the Asian region affect in a wide region as a complex mixture of AA and AD aerosols; they are predominated by the AD aerosol in the AD source region of northern China and Mongolia with a maximum concentration exceeding 300 μg m(-3); AAs are predominated in the high pollutant emission regions of southern and eastern China and northern India with a maximum concentration exceeding 110 μg m(-3); while the mixture of AA and AD aerosols is dominated in the downwind regions extending from the Yellow Sea to the Northwest Pacific Ocean. It is also found that the annual total deposition of aerosols in the model domain is found to be 485 Tg (372 Tg by AD aerosol and 113 Tg by AA), of which 66% (319 Tg) is contributed by the dry deposition (305 Tg by AD aerosol and 14 Tg by AA) and 34% (166 Tg) by the wet deposition (66 Tg by AD aerosol and 100 Tg by AA), suggesting about 77% of the annual total deposition being contributed by the AD aerosol mainly through the dry deposition process and 24% of it by AA through the wet deposition process. The monthly mean aerosol concentration and the monthly total deposition show a significant seasonal variation with high in winter and spring, and low in summer. PMID:26520259

  1. Concentrations and sources of metals in the Antarctic Peninsula aerosol

    SciTech Connect

    Dick, A.L. )

    1991-07-01

    Aerosol samples were collected at a remote site near the east coast of the Antarctic Peninsula during the austral summer of 1984/85. Filter samples were analyzed for Al (as a crustal reference element), marine cations (Na, K, and Ca), heavy metals (Cd, Cu, Pb, and Zn), and sulfate using atomic absorption spectrometry, isotope dilution mass spectrometry, neutron activation analysis, and ion chromatography. Ultraclean sample collection and analysis procedures used to avoid sample contamination are described in detail here. Mean concentrations of heavy metals were found to be: Cd, 0.06 pg m{sup {minus}3}; Cu, 1.0 pg m{sup {minus}3}; Pb, 4.7 pg m{sup {minus}3}; and Zn, 6.1 pg m{sup {minus}3}. These are the lowest concentrations yet determined in the troposphere, but for Pb and Zn they still indicate a significant enrichment over expected crustal concentrations. For these elements, estimated marine and volcanic contributions cannot account for this excess and suggest pollution as the dominant source even at this remote location. For Cd and Cu a dominant anthropogenic source cannot be ruled out, although current estimated of crustal, marine, a volcanic emissions could account for levels determined.

  2. Contributions of the pollutant emission in South Korea to the aerosol concentrations and depositions in Asia

    NASA Astrophysics Data System (ADS)

    Park, Soon-Ung; Lee, In-Hye; Choe, Anna; Joo, Seung Jin

    2015-05-01

    The spatial distributions of annual mean concentrations and the annual total depositions of the Asian dust (AD) aerosol and the anthropogenic aerosol (AA) in 2010 are investigated with pollutant emissions over the whole model domain of Asia and without the pollutant emission from South Korea using the Aerosol Modeling System (AMS) that is modified from the Asian Dust Aerosol Model2 (ADAM2) and the Community Multi-Scale Air Quality (CMAQ) modeling System. The annual mean surface aerosol concentrations in Asia are found to affect a wide region as a complex mixture of AA and AD aerosols. However, the contribution of the pollutant emission from South Korea is found to be limited to the neighboring regions. The annual total aerosol deposition in Asia is 485.2 Tg. However, the contribution due to the pollutant emission from South Korea is about 1.9 Tg, suggesting of no significant contribution to the environment.

  3. Analysis of number size distributions of tropical free tropospheric aerosol particles observed at Pico Espejo (4765 m a.s.l.), Venezuela

    NASA Astrophysics Data System (ADS)

    Schmeissner, T.; Krejci, R.; Ström, J.; Birmili, W.; Wiedensohler, A.; Hochschild, G.; Gross, J.; Hoffmann, P.; Calderon, S.

    2011-04-01

    The first long-term measurements of aerosol number and size distributions in South-American tropical free troposphere (FT) were performed from March 2007 until March 2009. The measurements took place at the high altitude Atmospheric Research Station Alexander von Humboldt. The station is located on top of the Sierra Nevada mountain ridge at 4765 m a.s.l. nearby the city of Mérida, Venezuela. Aerosol size distribution and number concentration data was obtained with a custom-built Differential Mobility Particle Sizer (DMPS) system and a Condensational Particle Counter (CPC). The analysis of the annual and diurnal variability of the tropical FT aerosol focused mainly on possible links to the atmospheric general circulation in the tropics. Considerable annual and diurnal cycles of the particle number concentration were observed. Highest total particle number concentrations were measured during the dry season (January-March, 519 ± 613 cm-3), lowest during the wet season (July-September, 318 ± 194 cm-3). The more humid FT (relative humidity (RH) range 50-95 %) contained generally higher aerosol particle number concentrations (573 ± 768 cm-3 during dry season, 320 ± 195 cm-3 during wet season) than the dry FT (RH < 50 %, 454 ± 332 cm-3 during dry season, 275 ± 172 cm-3 during wet season), indicating the importance of convection for aerosol distributions in the tropical FT. The diurnal cycle in the variability of the particle number concentration was mainly driven by local orography.

  4. Source appointment of fine particle number and volume concentration during severe haze pollution in Beijing in January 2013.

    PubMed

    Liu, Zirui; Wang, Yuesi; Hu, Bo; Ji, Dongsheng; Zhang, Junke; Wu, Fangkun; Wan, Xin; Wang, Yonghong

    2016-04-01

    Extreme haze episodes repeatedly shrouded Beijing during the winter of 2012-2013, causing major environmental and health problems. To better understand these extreme events, particle number size distribution (PNSD) and particle chemical composition (PCC) data collected in an intensive winter campaign in an urban site of Beijing were used to investigate the sources of ambient fine particles. Positive matrix factorization (PMF) analysis resolved a total of eight factors: two traffic factors, combustion factors, secondary aerosol, two accumulation mode aerosol factors, road dust, and long-range transported (LRT) dust. Traffic emissions (54 %) and combustion aerosol (27 %) were found to be the most important sources for particle number concentration, whereas combustion aerosol (33 %) and accumulation mode aerosol (37 %) dominated particle volume concentrations. Chemical compositions and sources of fine particles changed dynamically in the haze episodes. An enhanced role of secondary inorganic species was observed in the formation of haze pollution. Regional transport played an important role for high particles, contribution of which was on average up to 24-49 % during the haze episodes. Secondary aerosols from urban background presented the largest contributions (45 %) for the rapid increase of fine particles in the severest haze episode. In addition, the invasion of LRT dust aerosols further elevated the fine particles during the extreme haze episode. Our results showed a clear impact of regional transport on the local air pollution, suggesting the importance of regional-scale emission control measures in the local air quality management of Beijing. PMID:26667647

  5. Ice nucleation in the upper troposphere: Sensitivity to aerosol number density, temperature, and cooling rate

    SciTech Connect

    Jensen, E.J.; Toon, O.B.

    1994-09-01

    We have investigated the processes that control ice crystal nucleation in the upper troposphere using a numerical model. Nucleation of ice resulting from cooling was simulated for a range of aerosol number densities, initial temperatures, and cooling rates. In contrast to observations of stratus clouds, we find that the number of ice crystals that nucleate in cirrus is relatively insensitive to the number of aerosols present. The ice crystal size distribution at the end of the nucleation process is unaffected by the assumed initial aerosol number density. Essentially, nucleation continues until enough ice crystals are present such that their deposition growth rapidly depletes the vapor and shuts off any further nucleation. However, the number of ice crystals nucleated increases rapidly with decreasing initial temperature and increasing cooling rate. This temperature dependence alone could explain the large ice crystal number density observed in very cold tropical cirrus.

  6. Spatial variation of the aerosol concentration and deposition over the Mediterranean coastal zone

    NASA Astrophysics Data System (ADS)

    Piazzola, J.; Tedeschi, G.; Blot, R.

    2010-07-01

    A model for the spatial variation of aerosol concentrations and deposition along the coastal zone is of great interest for studies on air and water quality. In coastal areas, sea-spray aerosols generated at the sea surface by the interaction between wind and waves add to a continental contribution emitted from natural and/or anthropogenic sources. To include coastal effects in the model for the prediction of aerosol concentrations, Piazzola et al. (2003) developed the coastal Mediterranean aerosol model. The present paper deals with an extension of the Mediterranean coastal aerosol to a regional scale applied to the prediction of the sea surface flux deposition. This was achieved by the development of an automatic coupling process between the aerosol model and a regional meso-scale meteorological model which allows accounting for the details of the orography of the coast. The results show a non-homogeneous spatial coverage of aerosol concentrations over the northwestern Mediterranean. The simulations were then validated using aerosol size distributions recorded on board the ship "Atalante" for two kinds of meteorological conditions. Error calculations show a good performance of the coupling process since it predicts the aerosol concentration to within a maximum factor of 3 for particle radii between 0.1 to 10 µm. This process was then used to provide the spatial distribution of the particle deposition fluxes over the study area.

  7. Observations of high droplet number concentrations in Southern Ocean boundary layer clouds

    NASA Astrophysics Data System (ADS)

    Chubb, T.; Huang, Y.; Jensen, J.; Campos, T.; Siems, S.; Manton, M.

    2015-09-01

    Data from the standard cloud physics payload during the NSF/NCAR High-performance Instrumented Airborne Platform for Environmental Research (HIAPER) Pole-to-Pole Observations (HIPPO) campaigns provide a snapshot of unusual wintertime microphysical conditions in the boundary layer over the Southern Ocean. On 29 June 2011, the HIAPER sampled the boundary layer in a region of pre-frontal warm air advection between 58 and 48° S to the south of Tasmania. Cloud droplet number concentrations were consistent with climatological values in the northernmost profiles but were exceptionally high for wintertime in the Southern Ocean at 100-200 cm-3 in the southernmost profiles. Sub-micron (0.06aerosol concentrations for the southern profiles were up to 400 cm-3. Analysis of back trajectories and atmospheric chemistry observations revealed that while conditions in the troposphere were more typical of a clean remote ocean airmass, there was some evidence of continental or anthropogenic influence. However, the hypothesis of long range transport of continental aerosol fails to explain the magnitude of the aerosol and cloud droplet concentration in the boundary layer. Instead, the gale force surface winds in this case (wind speed at 167 m above sea level was >25 m s-1) were most likely responsible for production of sea spray aerosol which influenced the microphysical properties of the boundary layer clouds. The smaller size and higher number concentration of cloud droplets is inferred to increase the albedo of these clouds, and these conditions occur regularly, and are expected to increase in frequency, over windy parts of the Southern Ocean.

  8. Modelling particle number concentrations in a typical street canyon in Germany and analysis of future trends

    NASA Astrophysics Data System (ADS)

    Toenges-Schuller, N.; Schneider, Chr.; Niederau, A.; Vogt, R.; Birmili, W.

    2015-06-01

    An aerosol box model and a gas-phase chemistry box model were coupled to simulate particle number (PN) concentrations, both solid and volatile, in a typical street canyon with a high traffic volume in Germany. The simulation accounts for emission, nucleation and aerosol aging processes while dilution is parameterised by a simple two-stage process. Calculations were performed for the years 2010, 2015, 2020 and 2025, and for a vehicle fleet consisting of electric vehicles only ("electric mobility"). Projections including a high fraction of Euro-6 vehicles in the fleet suggest that PN emissions will reduce by 90% in 2025 compared to 2010. Ambient PN concentrations are, however, expected to reduce by merely 29% over the same period. Apart from contributions of urban background air, reductions in primary particles are partially offset by secondary particle formation by nucleating exhaust gases. In the "electric mobility" scenario omitting tailpipe emissions, PN concentrations are expected to reduce by 60% from 2010 to 2025. For an aerosol assumed to be mixed externally only, PN of elemental carbon (EC) was calculated to reduce by 76% from 2010 to 2025, in the "electric mobility" scenario by 87%. Overall, the contribution of solid PN emissions from gasoline vehicles to PN concentration in the street canyon is expected to be approximately 4% in 2025.

  9. Unexpectedly high ultrafine aerosol concentrations above East Antarctic sea-ice

    NASA Astrophysics Data System (ADS)

    Humphries, R. S.; Klekociuk, A. R.; Schofield, R.; Keywood, M.; Ward, J.; Wilson, S. R.

    2015-10-01

    The effect of aerosols on clouds and their radiative properties is one of the largest uncertainties in our understanding of radiative forcing. A recent study has concluded that better characterisation of pristine, natural aerosol processes leads to the largest reduction in these uncertainties. Antarctica, being far from anthropogenic activities, is an ideal location for the study of natural aerosol processes. Aerosol measurements in Antarctica are often limited to boundary layer air-masses at spatially sparse coastal and continental research stations, with only a handful of studies in the sea ice region. In this paper, the first observational study of sub-micron aerosols in the East Antarctic sea ice region is presented. Measurements were conducted aboard the ice-breaker Aurora Australis in spring 2012 and found that boundary layer condensation nuclei (CN3) concentrations exhibited a five-fold increase moving across the Polar Front, with mean Polar Cell concentrations of 1130 cm-3 - higher than any observed elsewhere in the Antarctic and Southern Ocean region. The absence of evidence for aerosol growth suggested that nucleation was unlikely to be local. Air parcel trajectories indicated significant influence from the free troposphere above the Antarctic continent, implicating this as the likely nucleation region for surface aerosol, a similar conclusion to previous Antarctic aerosol studies. The highest aerosol concentrations were found to correlate with low pressure systems, suggesting that the passage of cyclones provided an accelerated pathway, delivering air-masses quickly from the free-troposphere to the surface. After descent from the Antarctic free troposphere, trajectories suggest that sea ice boundary layer air-masses travelled equator-ward into the low albedo Southern Ocean region, transporting with them emissions and these aerosol nuclei where, after growth, may potentially impact on the region's radiative balance. The high aerosol concentrations and

  10. The effect of aerosol vertical profiles on satellite-estimated surface particle sulfate concentrations

    SciTech Connect

    Liu, Yang; Wang, Zifeng; Wang, Jun; Ferrare, Richard A.; Newsom, Rob K.; Welton, Ellsworth J.

    2011-02-15

    The aerosol vertical distribution is an important factor in determining the relationship between satellite retrieved aerosol optical depth (AOD) and ground-level fine particle pollution concentrations. We evaluate how aerosol profiles measured by ground-based lidar and simulated by models can help improve the association between AOD retrieved by the Multi-angle Imaging Spectroradiometer (MISR) and fine particle sulfate (SO4) concentrations using matched data at two lidar sites. At the Goddard Space Flight Center (GSFC) site, both lidar and model aerosol profiles marginally improve the association between SO4 concentrations and MISR fractional AODs, as the correlation coefficient between cross-validation (CV) and observed SO4 concentrations changes from 0.87 for the no-scaling model to 0.88 for models scaled with aerosol vertical profiles. At the GSFC site, a large amount of urban aerosols resides in the well-mixed boundary layer so the column fractional AODs are already excellent indicators of ground-level particle pollution. In contrast, at the Atmospheric Radiation Measurement Program (ARM) site with relatively low aerosol loadings, scaling substantially improves model performance. The correlation coefficient between CV and observed SO4 concentrations is increased from 0.58 for the no-scaling model to 0.76 in the GEOS-Chem scaling model, and the model bias is reduced from 17% to 9%. In summary, despite the inaccuracy due to the coarse horizontal resolution and the challenges of simulating turbulent mixing in the boundary layer, GEOS-Chem simulated aerosol profiles can still improve methods for estimating surface aerosol (SO4) mass from satellite-based AODs, particularly in rural areas where aerosols in the free troposphere and any long-range transport of aerosols can significantly contribute to the column AOD.

  11. Effect of Organic Sea Spray Aerosol on Global and Regional Cloud Condensation Nuclei Concentrations

    NASA Astrophysics Data System (ADS)

    Westervelt, D. M.; Nenes, A.; Moore, R.; Adams, P. J.

    2009-12-01

    Physical processes on the ocean surface (bubble bursting) result in formation of sea spray aerosol. It is now recognized that this aerosol source includes a significant amount of organic matter (O’Dowd et al. 2004). Higher amounts of aerosol lead to higher cloud condensation nuclei (CCN) concentrations, which perturb climate by brightening clouds in what is known as the aerosol indirect effect (Twomey 1977). This work quantifies the marine organic aerosol global emission source as well the effect of the aerosol on CCN by implementing an organic sea spray source function into a series of global aerosol simulations. The new organic sea spray source function correlates satellite retrieved chlorophyll concentrations to fraction of organic matter in sea spray aerosol (O’Dowd et al. 2008). Using this source function, a global marine organic aerosol emission rate of 17.2 Tg C yr-1 is estimated. Effect on CCN concentrations (0.2% supersaturation) is modeled using the Two-Moment Aerosol Sectional (TOMAS) microphysics algorithm coupled to a general circulation model (Adams and Seinfeld 2002). Upon including organic sea spray aerosol in global simulations, changes in CCN concentrations are induced by the changed aerosol composition as well as the ability of the organic matter to serve as surfactants. To explore surfactant effects, surface tension depression data from seawater samples taken near the Georgia coast were applied as a function of carbon concentrations (Moore et al. 2008). Preliminary findings suggest that organic sea spray aerosol exerts a localized influence on CCN(0.2%) concentrations. Surfactant effects appear to be the most important impact of marine organic aerosol on CCN(0.2%), as changes in aerosol composition alone have a weak influence, even in regions of high organic sea spray emissions. 1. O’Dowd, C.D., Facchini, M.C. et al., Nature, 431, (2004) 2. Twomey, S., J. Atmos. Sci., 34, (1977) 3. O’Dowd C.D et al. Geophys. Res. Let., 35, (2008) 4

  12. On the competition among aerosol number, size and composition in predicting CCN variability: a multi-annual field study in an urbanized desert

    NASA Astrophysics Data System (ADS)

    Crosbie, E.; Youn, J.-S.; Balch, B.; Wonaschütz, A.; Shingler, T.; Wang, Z.; Conant, W. C.; Betterton, E. A.; Sorooshian, A.

    2015-02-01

    A two-year dataset of measured CCN concentrations at 0.2% supersaturation is combined with aerosol size distribution and aerosol chemistry data to probe the effects of aerosol number concentrations, size distribution and composition on CCN patterns. Data have been collected over a period of two years (2012-2014) in central Tucson, Arizona: a significant urban area surrounded by a sparsely populated desert. Average CCN concentrations are typically lowest in spring (233 cm-3), highest in winter (430 cm-3) and have a secondary peak during the North American Monsoon season (July to September; 372 cm-3). There is significant variability outside of seasonal patterns with extreme concentrations (1 and 99% levels) ranging from 56 to 1945 cm-3 as measured during the winter, the season with highest variability. Modeled CCN concentrations based on fixed chemical composition achieve better closure in winter, with size and number alone able to predict 82% of the variance in CCN concentration. Changes in aerosol chemistry are typically aligned with changes in size and aerosol number, such that composition can be parameterized even though it is still variable. In summer, models based on fixed chemical composition explain at best only 41% (pre-monsoon) and 36% (monsoon) of the variance. This is attributed to the effects of secondary organic aerosol (SOA) production, the competition between new particle formation and condensational growth, and the complex interaction of meteorology, regional and local emissions, and multi-phase chemistry during the North American Monsoon. Chemical composition is found to be an important factor for improving predictability in spring and on longer timescales in winter. Regimes where parameterized models exhibit improved predictive skill are typically explained by strong relationships between CCN concentrations and the prevailing meteorology and dominant aerosol chemistry mechanisms suggesting that similar findings could be possible in other locations

  13. On the competition among aerosol number, size and composition in predicting CCN variability: a multi-annual field study in an urbanized desert

    NASA Astrophysics Data System (ADS)

    Crosbie, E.; Youn, J.-S.; Balch, B.; Wonaschütz, A.; Shingler, T.; Wang, Z.; Conant, W. C.; Betterton, E. A.; Sorooshian, A.

    2015-06-01

    A 2-year data set of measured CCN (cloud condensation nuclei) concentrations at 0.2 % supersaturation is combined with aerosol size distribution and aerosol composition data to probe the effects of aerosol number concentrations, size distribution and composition on CCN patterns. Data were collected over a period of 2 years (2012-2014) in central Tucson, Arizona: a significant urban area surrounded by a sparsely populated desert. Average CCN concentrations are typically lowest in spring (233 cm-3), highest in winter (430 cm-3) and have a secondary peak during the North American monsoon season (July to September; 372 cm-3). There is significant variability outside of seasonal patterns, with extreme concentrations (1 and 99 % levels) ranging from 56 to 1945 cm-3 as measured during the winter, the season with highest variability. Modeled CCN concentrations based on fixed chemical composition achieve better closure in winter, with size and number alone able to predict 82 % of the variance in CCN concentration. Changes in aerosol chemical composition are typically aligned with changes in size and aerosol number, such that hygroscopicity can be parameterized even though it is still variable. In summer, models based on fixed chemical composition explain at best only 41 % (pre-monsoon) and 36 % (monsoon) of the variance. This is attributed to the effects of secondary organic aerosol (SOA) production, the competition between new particle formation and condensational growth, the complex interaction of meteorology, regional and local emissions and multi-phase chemistry during the North American monsoon. Chemical composition is found to be an important factor for improving predictability in spring and on longer timescales in winter. Parameterized models typically exhibit improved predictive skill when there are strong relationships between CCN concentrations and the prevailing meteorology and dominant aerosol physicochemical processes, suggesting that similar findings could be

  14. On the competition among aerosol number, size and composition in predicting CCN variability: a multi-annual field study in an urbanized desert

    NASA Astrophysics Data System (ADS)

    Crosbie, Ewan; Youn, Jong-Sang; Balch, Brian; Wonaschuetz, Anna; Shingler, Taylor; Wang, Zhen; Conant, William; Betterton, Eric; Sorooshian, Armin

    2015-04-01

    A two-year dataset of measured CCN concentrations at 0.2% supersaturation is combined with aerosol size distribution and aerosol chemistry data to probe the effects of aerosol number concentrations, size distribution and composition on CCN patterns. Data have been collected over a period of two years (2012-2014) in central Tucson, Arizona: a significant urban area surrounded by a sparsely populated desert. Average CCN concentrations are typically lowest in spring (233 cm-3), highest in winter (430 cm-3) and have a secondary peak during the North American Monsoon season (July to September; 372 cm-3). There is significant variability outside of seasonal patterns with extreme concentrations (1% and 99% levels) ranging from 56 cm-3 to 1945 cm-3 as measured during the winter, the season with highest variability. Modeled CCN concentrations based on fixed chemical composition achieve better closure in winter, with size and number alone able to predict 82% of the variance in CCN concentration. Changes in aerosol chemistry are typically aligned with changes in size and aerosol number, such that composition can be parameterized even though it is still variable. In summer, models based on fixed chemical composition explain at best only 41% (pre-monsoon) and 36% (monsoon) of the variance. This is attributed to the effects of secondary organic aerosol (SOA) production, the competition between new particle formation and condensational growth, and the complex interaction of meteorology, regional and local emissions, and multi-phase chemistry during the North American Monsoon. Chemical composition is found to be an important factor for improving predictability in spring and on longer timescales in winter. Regimes where parameterized models exhibit improved predictive skill are typically explained by strong relationships between CCN concentrations and the prevailing meteorology and dominant aerosol chemistry mechanisms suggesting that similar findings could be possible in other

  15. On the competition among aerosol number, size and composition in predicting CCN variability: a multi-annual field study in an urbanized desert

    PubMed Central

    Crosbie, E.; Youn, J.-S.; Balch, B.; Wonaschütz, A.; Shingler, T.; Wang, Z.; Conant, W. C.; Betterton, E. A.; Sorooshian, A.

    2015-01-01

    A 2-year data set of measured CCN (cloud condensation nuclei) concentrations at 0.2 % supersaturation is combined with aerosol size distribution and aerosol composition data to probe the effects of aerosol number concentrations, size distribution and composition on CCN patterns. Data were collected over a period of 2 years (2012–2014) in central Tucson, Arizona: a significant urban area surrounded by a sparsely populated desert. Average CCN concentrations are typically lowest in spring (233 cm−3), highest in winter (430 cm−3) and have a secondary peak during the North American monsoon season (July to September; 372 cm−3). There is significant variability outside of seasonal patterns, with extreme concentrations (1 and 99 % levels) ranging from 56 to 1945 cm−3 as measured during the winter, the season with highest variability. Modeled CCN concentrations based on fixed chemical composition achieve better closure in winter, with size and number alone able to predict 82% of the variance in CCN concentration. Changes in aerosol chemical composition are typically aligned with changes in size and aerosol number, such that hygroscopicity can be parameterized even though it is still variable. In summer, models based on fixed chemical composition explain at best only 41% (pre-monsoon) and 36% (monsoon) of the variance. This is attributed to the effects of secondary organic aerosol (SOA) production, the competition between new particle formation and condensational growth, the complex interaction of meteorology, regional and local emissions and multi-phase chemistry during the North American monsoon. Chemical composition is found to be an important factor for improving predictability in spring and on longer timescales in winter. Parameterized models typically exhibit improved predictive skill when there are strong relationships between CCN concentrations and the prevailing meteorology and dominant aerosol physicochemical processes, suggesting that similar findings

  16. A qualitative comparison of secondary organic aerosol yields and composition from ozonolysis of monoterpenes at varying concentrations of NO2

    NASA Astrophysics Data System (ADS)

    Draper, D. C.; Farmer, D. K.; Desyaterik, Y.; Fry, J. L.

    2015-11-01

    The effect of NO2 on secondary organic aerosol (SOA) formation from ozonolysis of α-pinene, β-pinene, Δ3-carene, and limonene was investigated using a dark flow-through reaction chamber. SOA mass yields were calculated for each monoterpene from ozonolysis with varying NO2 concentrations. Kinetics modeling of the first-generation gas-phase chemistry suggests that differences in observed aerosol yields for different NO2 concentrations are consistent with NO3 formation and subsequent competition between O3 and NO3 to oxidize each monoterpene. α-Pinene was the only monoterpene studied that showed a systematic decrease in both aerosol number concentration and mass concentration with increasing [NO2]. β-Pinene and Δ3-carene produced fewer particles at higher [NO2], but both retained moderate mass yields. Limonene exhibited both higher number concentrations and greater mass concentrations at higher [NO2]. SOA from each experiment was collected and analyzed by HPLC-ESI-MS, enabling comparisons between product distributions for each system. In general, the systems influenced by NO3 oxidation contained more high molecular weight products (MW > 400 amu), suggesting the importance of oligomerization mechanisms in NO3-initiated SOA formation. α-Pinene, which showed anomalously low aerosol mass yields in the presence of NO2, showed no increase in these oligomer peaks, suggesting that lack of oligomer formation is a likely cause of α-pinene's near 0 % yields with NO3. Through direct comparisons of mixed-oxidant systems, this work suggests that NO3 is likely to dominate nighttime oxidation pathways in most regions with both biogenic and anthropogenic influences. Therefore, accurately constraining SOA yields from NO3 oxidation, which vary substantially with the volatile organic compound precursor, is essential in predicting nighttime aerosol production.

  17. A comparison of secondary organic aerosol (SOA) yields and composition from ozonolysis of monoterpenes at varying concentrations of NO2

    NASA Astrophysics Data System (ADS)

    Draper, D. C.; Farmer, D. K.; Desyaterik, Y.; Fry, J. L.

    2015-05-01

    The effect of NO2 on secondary organic aerosol (SOA) formation from ozonolysis of α-pinene, β-pinene, Δ3-carene, and limonene was investigated using a dark flow-through reaction chamber. SOA mass yields were calculated for each monoterpene from ozonolysis with varying NO2 concentrations. Kinetics modeling of the first generation gas-phase chemistry suggests that differences in observed aerosol yields for different NO2 concentrations are consistent with NO3 formation and subsequent competition between O3 and NO3 to oxidize each monoterpene. α-pinene was the only monoterpene studied that showed a systematic decrease in both aerosol number concentration and mass concentration with increasing [NO2]. β-pinene and Δ3-carene produced fewer particles at higher [NO2], but both retained moderate mass yields. Limonene exhibited both higher number concentrations and greater mass concentrations at higher [NO2]. SOA from each experiment was collected and analyzed by HPLC-ESI-MS, enabling comparisons between product distributions for each system. In general, the systems influenced by NO3 oxidation contained more high molecular weight products (MW >400 amu), suggesting the importance of oligomerization mechanisms in NO3-initiated SOA formation. α-pinene, which showed anomalously low aerosol mass yields in the presence of NO2, showed no increase in these oligomer peaks, suggesting that lack of oligomer formation is a likely cause of α-pinene's near 0% yields with NO3. Through direct comparisons of mixed-oxidant systems, this work suggests that NO3 is likely to dominate nighttime oxidation pathways in most regions with both biogenic and anthropogenic influences. Therefore, accurately constraining SOA yields from NO3 oxidation, which vary substantially with the VOC precursor, is essential in predicting nighttime aerosol production.

  18. Processes controlling the annual cycle of Arctic aerosol number and size distributions

    NASA Astrophysics Data System (ADS)

    Croft, Betty; Martin, Randall V.; Leaitch, W. Richard; Tunved, Peter; Breider, Thomas J.; D'Andrea, Stephen D.; Pierce, Jeffrey R.

    2016-03-01

    Measurements at high-Arctic sites (Alert, Nunavut, and Mt. Zeppelin, Svalbard) during the years 2011 to 2013 show a strong and similar annual cycle in aerosol number and size distributions. Each year at both sites, the number of aerosols with diameters larger than 20 nm exhibits a minimum in October and two maxima, one in spring associated with a dominant accumulation mode (particles 100 to 500 nm in diameter) and a second in summer associated with a dominant Aitken mode (particles 20 to 100 nm in diameter). Seasonal-mean aerosol effective diameter from measurements ranges from about 180 in summer to 260 nm in winter. This study interprets these annual cycles with the GEOS-Chem-TOMAS global aerosol microphysics model. Important roles are documented for several processes (new-particle formation, coagulation scavenging in clouds, scavenging by precipitation, and transport) in controlling the annual cycle in Arctic aerosol number and size. Our simulations suggest that coagulation scavenging of interstitial aerosols in clouds by aerosols that have activated to form cloud droplets strongly limits the total number of particles with diameters less than 200 nm throughout the year. We find that the minimum in total particle number in October can be explained by diminishing new-particle formation within the Arctic, limited transport of pollution from lower latitudes, and efficient wet removal. Our simulations indicate that the summertime-dominant Aitken mode is associated with efficient wet removal of accumulation-mode aerosols, which limits the condensation sink for condensable vapours. This in turn promotes new-particle formation and growth. The dominant accumulation mode during spring is associated with build up of transported pollution from outside the Arctic coupled with less-efficient wet-removal processes at colder temperatures. We recommend further attention to the key processes of new-particle formation, interstitial coagulation, and wet removal and their delicate

  19. First measurements of aerosol optical depth and Angstrom exponent number from AERONET's Kuching site

    NASA Astrophysics Data System (ADS)

    Salinas, Santo V.; Chew, Boon N.; Mohamad, M.; Mahmud, M.; Liew, Soo C.

    2013-10-01

    We report our first measurements, over the 2011 dry season period, of aerosol optical depth, Angstrom exponent number and its fine mode counterpart obtained from photometric measurements at AERONET's newest site located at the city of Kuching, Sarawak, East Malaysia. This site was set up as part of the collaborative efforts of the Seven South East Asian Studies (7SEAS) regional aerosol measurements initiative. Located at the converging zone between peninsular Malaysia and the land masses of Sumatra, Borneo, Java and Sulawesi, this site is expected to provide first hand evidence about the physical and optical characteristics of the regional aerosol environment, specially during the biomass burning months. Moreover, given its relative proximity to our Singapore radiation measurement super-site, Kuching is expected to provide further insight on aerosol transport pathways caused by seasonal winds transporting smoke to other parts of the maritime continent and the South Asia region.

  20. Concentrations and sources of organic carbon aerosols in the free troposphere over North America

    NASA Astrophysics Data System (ADS)

    Heald, Colette L.; Jacob, Daniel J.; Turquety, SolèNe; Hudman, Rynda C.; Weber, Rodney J.; Sullivan, Amy P.; Peltier, Richard E.; Atlas, Eliot L.; de Gouw, Joost A.; Warneke, Carsten; Holloway, John S.; Neuman, J. Andrew; Flocke, Frank M.; Seinfeld, John H.

    2006-12-01

    Aircraft measurements of water-soluble organic carbon (WSOC) aerosol over NE North America during summer 2004 (ITCT-2K4) are simulated with a global chemical transport model (GEOS-Chem) to test our understanding of the sources of organic carbon (OC) aerosol in the free troposphere (FT). Elevated concentrations were observed in plumes from boreal fires in Alaska and Canada. WSOC aerosol concentrations outside of these plumes average 0.9 ± 0.9 μg C m-3 in the FT (2-6 km). The corresponding model value is 0.7 ± 0.6 μg C m-3, including 42% from biomass burning, 36% from biogenic secondary organic aerosol (SOA), and 22% from anthropogenic emissions. Previous OC aerosol observations over the NW Pacific in spring 2001 (ACE-Asia) averaged 3.3 ± 2.8 μg C m-3 in the FT, compared to a model value of 0.3 ± 0.3 μg C m-3. WSOC aerosol concentrations in the boundary layer (BL) during ITCT-2K4 are consistent with OC aerosol observed at the IMPROVE surface network. The model is low in the boundary layer by 30%, which we attribute to secondary formation at a rate comparable to primary anthropogenic emission. Observed WSOC aerosol concentrations decrease by a factor of 2 from the BL to the FT, as compared to a factor of 10 decrease for sulfate, indicating that most of the WSOC aerosol in the FT originates in situ. Despite reproducing mean observed WSOC concentrations in the FT to within 25%, the model cannot account for the variance in the observations (R = 0.21). Covariance analysis of FT WSOC aerosol with other measured chemical variables suggests an aqueous-phase mechanism for SOA generation involving biogenic precursors.

  1. Evaluation of a Low-Cost Aerosol Sensor to Assess Dust Concentrations in a Swine Building.

    PubMed

    Jones, Samuel; Anthony, T Renée; Sousan, Sinan; Altmaier, Ralph; Park, Jae Hong; Peters, Thomas M

    2016-06-01

    Exposure to dust is a known occupational hazard in the swine industry, although efforts to measure exposures are labor intensive and costly. In this study, we evaluated a Dylos DC1100 as a low-cost (~$200) alternative to assess respirable dust concentrations in a swine building in winter. Dust concentrations were measured with collocated monitors (Dylos DC1100; an aerosol photometer, the pDR-1200; and a respirable sampler analyzed gravimetrically) placed in two locations within a swine farrowing building in winter for 18-24-h periods. The particle number concentrations measured with the DC1100 were converted to mass concentration using two methods: Physical Property Method and Regression Method. Raw number concentrations from the DC1100 were highly correlated to mass concentrations measured with the pDR-1200 with a coefficient of determination (R (2)) of 0.85, indicating that the two monitors respond similarly to respirable dust in this environment. Both methods of converting DC1100 number concentrations to mass concentrations yielded strong linear relationships relative to that measured with the pDR-1200 (Physical Property Method: slope = 1.03, R (2) = 0.72; Regression Method: slope = 0.72, R (2) = 0.73) and relative to that measured gravimetrically (Physical Property Method: slope = 1.08, R (2) = 0.64; Regression Method: slope = 0.75, R (2) = 0.62). The DC1100 can be used as a reasonable indicator of respirable mass concentrations within a CAFO and may have broader applicability to other agricultural and industrial settings. PMID:26944922

  2. Calculating Capstone depleted uranium aerosol concentrations from beta activity measurements.

    PubMed

    Szrom, Frances; Falo, Gerald A; Parkhurst, Mary Ann; Whicker, Jeffrey J; Alberth, David P

    2009-03-01

    Beta activity measurements were used as surrogate measurements of uranium mass in aerosol samples collected during the field testing phase of the Capstone Depleted Uranium (DU) Aerosol Study. These aerosol samples generated by the perforation of armored combat vehicles were used to characterize the DU source term for the subsequent Human Health Risk Assessment (HHRA) of Capstone aerosols. Establishing a calibration curve between beta activity measurements and uranium mass measurements is straightforward if the uranium isotopes are in equilibrium with their immediate short-lived, beta-emitting progeny. For DU samples collected during the Capstone study, it was determined that the equilibrium between the uranium isotopes and their immediate short-lived, beta-emitting progeny had been disrupted when penetrators had perforated target vehicles. Adjustments were made to account for the disrupted equilibrium and for wall losses in the aerosol samplers. Values for the equilibrium fraction ranged from 0.16 to 1, and the wall loss correction factors ranged from 1 to 1.92. This paper describes the process used and adjustments necessary to calculate uranium mass from proportional counting measurements. PMID:19204483

  3. Calculating Capstone Depleted Uranium Aerosol Concentrations from Beta Activity Measurements

    SciTech Connect

    Szrom, Fran; Falo, Gerald A.; Parkhurst, MaryAnn; Whicker, Jeffrey J.; Alberth, David P.

    2009-03-01

    Beta activity measurements were used as surrogate measurements of uranium mass in aerosol samples collected during the field testing phase of the Capstone Depleted Uranium (DU) Aerosol Study. These aerosol samples generated by the perforation of armored combat vehicles were used to characterize the depleted uranium (DU) source term for the subsequent human health risk assessment (HHRA) of Capstone aerosols. Establishing a calibration curve between beta activity measurements and uranium mass measurements is straightforward if the uranium isotopes are in equilibrium with their immediate short-lived, beta-emitting progeny. For DU samples collected during the Capstone study, it was determined that the equilibrium between the uranium isotopes and their immediate short lived, beta-emitting progeny had been disrupted when penetrators had perforated target vehicles. Adjustments were made to account for the disrupted equilibrium and for wall losses in the aerosol samplers. Correction factors for the disrupted equilibrium ranged from 0.16 to 1, and the wall loss correction factors ranged from 1 to 1.92.

  4. Number size distribution of aerosols at Mt. Huang and Nanjing in the Yangtze River Delta, China: Effects of air masses and characteristics of new particle formation

    NASA Astrophysics Data System (ADS)

    Wang, Honglei; Zhu, Bin; Shen, Lijuan; An, Junlin; Yin, Yan; Kang, Hanqing

    2014-12-01

    Aerosol number spectra in the range of 10 nm-10 μm were observed at Mt. Huang (Aug. 15-Sep. 15) and Nanjing (Oct. 13-Nov. 15) by a wide-range particle spectrometer (WPS) in 2011. Based on the backward trajectories obtained using the HYSPLIT model, the transport pathways of observed air masses during the study periods were classified into the following four groups: maritime air mass, continental air mass, marine-continental mixed air mass and local air mass. The variations in the aerosol number spectrum and the new particle formation (NPF) events for various types of air masses were discussed, along with meteorological data. The results showed that the average number concentration was 12,540 cm- 3 at Nanjing and only 2791 cm- 3 at Mt. Huang. The aerosol number concentration in Nanjing was 3-7 times higher than that in Mt. Huang; the large discrepancy was in the range of 10-100 nm. Different types of air masses had different effects on number concentration distribution. The number concentration of aerosols was higher in marine air masses, continental air masses and continental-marine mixed air masses at 10-50 nm, 100-500 nm and 50-200 nm, respectively. Under the four types of air masses, the aerosol size spectra had bimodal distributions in Nanjing and unimodal distributions in Mt. Huang (except under continental air masses: HT1). The effects of the diverse air masses on aerosol size segments of the concentration peak in Mt. Huang were stronger than those in Nanjing. The local air masses were dominant at these two sites and accounted for 44% of the total air masses. However, the aerosol number concentration was the lowest in Mt. Huang and the highest in Nanjing when local air masses were present. The number concentrations for foreign air masses increased at Mt. Huang and decreased at Nanjing. Different types of air masses had greater effects on the aerosol spectrum distribution at Mt. Huang than at Nanjing. During the NPF events, the particle growth rates at Mt

  5. On the relationship between sulfate and cloud droplet number concentrations

    SciTech Connect

    Leaitch, W.R.; Isaac, G.A. )

    1994-01-01

    Comparisons are drawn between the aerosol cloud microphysical theory implicit in the modeling of Kaufman et al. and the cloud droplet and cloud water sulfate concentrations of Leaitch et al. for the purpose of helping to understand the effect of sulfate particle son climate through cloud modification. In terms of the range of possibilities and prospects for future climate given by Kaufman et al. for the effect of sulfur on cloud albedo, the data favor the possibility of stronger cooling. Scatter in the data makes it impossible to constrain model parameters; however, the comparisons suggest that there may not be a universal relationship, and that the uncertainties involved in trying to model this process are large.

  6. A balloon-borne aerosol spectrometer for high altitude low aerosol concentration measurements

    SciTech Connect

    Brown, G.S. ); Weiss, R.E. )

    1990-08-01

    Funded by Air Force Wright Aeronautical Laboratory, a new balloon-borne high altitude aerosol spectrometer, for the measurement of cirrus cloud ice crystals, has been developed and successfully flown by Sandia National Laboratories and Radiance Research. This report (1) details the aerosol spectrometer design and construction, (2) discusses data transmission and decoding, (3) presents data collected on three Florida flights in tables and plots. 2 refs., 11 figs., 3 tabs.

  7. What controls the low ice number concentration in the upper troposphere?

    NASA Astrophysics Data System (ADS)

    Zhou, C.; Penner, J. E.; Lin, G.; Liu, X.; Wang, M.

    2015-12-01

    Cirrus clouds in the tropical tropopause play a key role in regulating the moisture entering the stratosphere through their dehydrating effect. Low ice number concentrations (< 200 L-1) and high supersaturations (150-160 %) have been observed in these clouds. Different mechanisms have been proposed to explain these low ice number concentrations, including the inhibition of homogeneous freezing by the deposition of water vapour onto pre-existing ice crystals, heterogeneous ice formation on glassy organic aerosol ice nuclei (IN), and limiting the formation of ice number from high frequency gravity waves. In this study, we examined the effect from three different representations of updraft velocities, the effect from pre-existing ice crystals, the effect from different water vapour deposition coefficients (α = 0.1 or 1), and the effect of 0.1 % of the total secondary organic aerosol (SOA) particles acting as IN. Model simulated ice crystal numbers are compared against an aircraft observational dataset. Including the effect from water vapour deposition on pre-existing ice particles can effectively reduce simulated in-cloud ice number concentrations for all model set-ups. A larger water vapour deposition coefficient (α = 1) can also efficiently reduce ice number concentrations at temperatures below 205 K but less so at higher temperatures. SOA acting as IN are most effective at reducing ice number concentrations when the effective updraft velocities are moderate (∼ 0.05-0.2 m s-1). However, the effects of including SOA as IN and using (α = 1) are diminished when the effect from pre-existing ice is included. When a grid resolved large-scale updraft velocity (< 0.1 m s-1) is used, the ice nucleation parameterization with homogeneous freezing only or with both homogeneous freezing and heterogeneous nucleation is able to generate low ice number concentrations in good agreement with observations for temperatures below 205 K as long as the pre-existing ice effect is

  8. Factors affecting the indoor concentrations of carbonaceous aerosols of outdoor origin

    SciTech Connect

    Lunden, Melissa M.; Kirchstetter, Thomas W.; Thatcher, Tracy L.; Hering, Susanne V.; Brown, Nancy J.

    2007-06-25

    A field study was conducted in an unoccupied single story residence in Clovis, California to provide data to address issues important to assess the indoor exposure to particles of outdoor origin. Measurements of black and organic carbonaceous aerosols were performed using a variety of methods, resulting in both near real-time measurements as well as integrated filter based measurements. Comparisons of the different measurement methods show that it is crucial to account for gas phase adsorption artifacts when measuring organic carbon (OC). Measured concentrations affected by the emissions of organic compounds sorbed to indoor surfaces imply a higher degree of infiltration of outdoor organic carbon aerosols into the indoor environment for our unoccupied house. Analysis of the indoor and outdoor data for black carbon (BC) aerosols show that, on average, the indoor concentration of black carbon aerosols behaves in a similar manner to sulfate aerosols. In contrast, organic carbon aerosols are subject to chemical transformations indoors that, for our unoccupied home, resulted in lower indoor OC concentrations than would be expected by physical loss mechanisms alone. These results show that gas to particle partitioning of organic compounds, as well as gas to surface interactions within the residence, are an important process governing the indoor concentration to OC aerosols of outdoor origin.

  9. Atmospheric aerosols: increased concentrations during the last decade.

    PubMed

    Peterson, J T; Bryson, R A

    1968-10-01

    Atmospheric turbidity values calculated each month from solar radiation observations at MaunaLoa Observatory, Hawaii, show an increase of aerosols from 1958 through the present. These data indicate that either the effects of the Mount Agung eruption are still being observed or a longer-term trend of increasing turbidity is in evidence. PMID:4877369

  10. Middle East measurements of concentration and size distribution of aerosol particles for coastal zones

    NASA Astrophysics Data System (ADS)

    Bendersky, Sergey; Kopeika, Norman S.; Blaunstein, Natan S.

    2005-10-01

    Recently, an extension of the Navy Aerosol Model (NAM) was proposed based on analysis of an extensive series of measurements at the Irish Atlantic Coast and at the French Mediterranean Coast. We confirm the relevance of that work for the distant eastern Meditteranean and extend several coefficients of that coastal model, proposed by Piazzola et al. for the Meditteranean Coast (a form of the Navy Aerosol Model), to midland Middle East coastal environments. This analysis is based on data collected at three different Middle East coastal areas: the Negev Desert (Eilat) Red Sea Coast, the Sea of Galilee (Tiberias) Coast, and the Mediterranean (Haifa) Coast. Aerosol size distributions are compared with those obtained through measurements carried out over the Atlantic, Pacific, and Indian Ocean Coasts, and Mediterranean, and Baltic Seas Coasts. An analysis of these different results allows better understanding of the similarities and differences between different coastal lake, sea, and open ocean zones. It is shown that in the coastal regions in Israel, compared to open ocean and other sea zones, larger differences in aerosol particle concentration are observed. The aerosol particle concentrations and their dependences on wind speed for these coastal zones are analyzed and discussed. We propose to classify the aerosol distribution models to either: 1. a coastal model with marine aerosol domination; 2. a coastal model with continental aerosol domination (referred to as midland coast in this work); or 3. a coastal model with balanced marine and continental conditions.

  11. Tropospheric Vertical Profiles of Aerosol Optical, Microphysical and Concentration Properties in the Frame of the Hygra-CD Campaign (Athens, Greece 2014): A Case Study of Long-Range Transport of Mixed Aerosols

    NASA Astrophysics Data System (ADS)

    Papayannis, Alexandros; Argyrouli, Athina; Müller, Detlef; Tsaknakis, Georgios; Kokkalis, Panayotis; Binietoglou, Ioannis; Kazadzis, Stelios; Solomos, Stavros; Amiridis, Vassilis

    2016-06-01

    Combined multi-wavelength aerosol Raman lidar and sun photometry measurements were performed during the HYGRA-CD campaign over Athens, Greece during May-June 2014. The retrieved aerosol optical properties (3 aerosol backscatter at 355-532-1064 nm and 2 aerosol extinction profiles at 355-532 nm) were used as input to an inversion code to retrieve the aerosol microphysical properties (effective radius reff and number concentration N) using regularization techniques. Additionally, the volume concentration profile was derived for fine particles using the LIRIC code. In this paper we selected a complex case study of long-range transport of mixed aerosols (biomass burning particles mixed with dust) arriving over Athens between 10-12 June 2014 in the 1.5-4 km height. Between 2-3 km height we measured mean lidar ratios (LR) ranging from 45 to 58 sr (at 355 and 532 nm), while the Ångström exponent (AE) aerosol extinction-related values (355nm/532nm) ranged between 0.8-1.3. The retrieved values of reff and N ranged from 0.19±0.07 to 0.22±0.07 μm and 460±230 to 2200±2800 cm-3, respectively. The aerosol linear depolarization ratio (δ) at 532 nm was lower than 5-7% (except for the Saharan dust cases, where δ~10-15%).

  12. On the concentration and size distribution of sub-micron aerosol in the Galápagos Islands

    NASA Astrophysics Data System (ADS)

    Sorribas, M.; Gómez Martín, J. C.; Hay, T. D.; Mahajan, A. S.; Cuevas, C. A.; Agama Reyes, M. V.; Paredes Mora, F.; Gil-Ojeda, M.; Saiz-Lopez, A.

    2015-12-01

    During the CHARLEX campaign in the Galápagos Islands, a Scanning Particle Mobility Sizer was deployed on San Cristobal Island in July-August 2011 to carry out size-resolved measurements of the concentration of submicron aerosols. To our knowledge these are the first measurements of aerosol concentrations in this unique environment. The particles with marine origin displayed a tri-modal number size distribution with peak diameters of 0.016 μm, 0.050 μm and 0.174 μm and a cloud-processed intermodal minimum at 0.093 μm. The mean total aerosol number concentration for the marine contribution was 470 ± 160 cm-3. A low particle concentration of 70 ± 50 cm-3 for the nucleation size range was measured, but no evidence of new particle production in the atmospheric marine boundary layer (MBL) was observed. The concentration of the Aitken size mode was found to be related to aerosol entrainment from the free troposphere off the coast of Chile followed by transport within the MBL to the Galápagos Islands. Cloud processing may activate the particles in the Aitken size range, growing through 'in-cloud' sulphate production and increasing the particle concentration in the accumulation size range. The 0.093 μm cloud processed minima suggests that the critical supersaturation at which the particle is activated to a cloud droplet is in the 0.14-0.21% range. The daytime marine particle background concentration was influenced by human activity around the sampling site, as well as by new particle formation triggered by biogenic emissions from the vegetation cover of the island's semiarid lowlands. Effective CCN formation may play a role in the formation and properties of the stratus clouds, which permanently cover the top of the windward side of the islands and establish one of their characteristic climatic bands.

  13. Measured and modelled cloud condensation nuclei (CCN) concentration in São Paulo, Brazil: the importance of aerosol size-resolved chemical composition on CCNhack concentration prediction

    NASA Astrophysics Data System (ADS)

    Almeida, G. P.; Brito, J.; Morales, C. A.; Andrade, M. F.; Artaxo, P.

    2014-07-01

    Measurements of cloud condensation nuclei (CCN), aerosol size distribution and non-refractory chemical composition were performed from 16 to 31 October 2012 in the São Paulo Metropolitan Area (SPMA), Brazil. CCN measurements were performed at 0.23, 0.45, 0.68, 0.90 and 1.13% water supersaturation and were subsequently compared with the Köhler theory, considering the chemical composition. Real-time chemical composition has been obtained by deploying, for the first time in the SPMA, an aerosol chemical ionization monitor (ACSM). CCN closure analyses were performed considering internal mixtures. Average aerosol composition during the studied period yielded (arithmetic mean~± standard deviation) 4.81 ± 3.05, 3.26 ± 2.10, 0.30 ± 0.27, 0.52 ± 0.32, 0.37 ± 0.21 and 0.04 ± 0.04 μg m-3 for organics, BC, NH4, SO4, NO3 and Cl, respectively. Particle number concentration was 12 813 ± 5350 cm-3, with a dominant nucleation mode. CCN concentrations were on average 1090 ± 328 and 3570 ± 1695 cm-3 at SS = 0.23% and SS = 1.13%, respectively. Results show an increase in aerosol hygroscopicity in the afternoon as a result of aerosol photochemical processing, leading to an enhancement of both organic and inorganic secondary aerosols in the atmosphere, as well as an increase in aerosol average diameter. Considering the bulk composition alone, observed CCN concentrations were substantially overpredicted when compared with the Köhler theory (44.1 ± 47.9% at 0.23% supersaturation and 91.4 ± 40.3% at 1.13% supersaturation). Overall, the impact of composition on the calculated CCN concentration (NCCN) decreases with decreasing supersaturation, partially because using bulk composition introduces less bias for large diameters and lower critical supersaturations, defined as the supersaturation at which the cloud droplet activation will take place. Results suggest that the consideration of only inorganic fraction improves the calculated NCCN. Introducing a size-dependent chemical

  14. Organosulfates and organic acids in Arctic aerosols: speciation, annual variation and concentration levels

    NASA Astrophysics Data System (ADS)

    Hansen, A. M. K.; Kristensen, K.; Nguyen, Q. T.; Zare, A.; Cozzi, F.; Nøjgaard, J. K.; Skov, H.; Brandt, J.; Christensen, J. H.; Ström, J.; Tunved, P.; Krejci, R.; Glasius, M.

    2014-02-01

    , organosulfate and organic acid concentrations remained relatively constant during most of the year at amean concentration of 15 (±4) ng m-3 (accounting for 4 (±1)% of total organic matter) and 3.9 (±1) ng m-3 (accounting for 1.1 (±0.1)% of total organic matter) respectively. However during four weeks of spring remarkably higher concentrations of total organosulfates (23-36 ng m-3) and total organic acids (7-10 ng m-3) were observed. The periods of observed elevated organosulfate and organic acid concentration at Station Nord and at Zeppelin Mountain coincided with the Arctic Haze period. Furthermore, backwards air mass trajectories indicated northern Eurasia as the main source region of the Arctic haze aerosols at both sites. Periods with air mass transport from Russia to Zeppelin Mountain were associated with a doubled number of detected organosulfate species compared with periods of air mass transport from the Arctic Ocean, Scandinavia and Greenland. Our analysis showed the presence of organosulfates and organic acids of both biogenic and anthropogenic origin throughout the year at both Arctic sites. As the formation of organosulfates binds inorganic sulfate, their presence may possibly affect the formation and lifetime of clouds in the Arctic atmosphere.

  15. Particle number concentration, size distribution and chemical composition during haze and photochemical smog episodes in Shanghai.

    PubMed

    Wang, Xuemei; Chen, Jianmin; Cheng, Tiantao; Zhang, Renyi; Wang, Xinming

    2014-09-01

    The aerosol number concentration and size distribution as well as size-resolved particle chemical composition were measured during haze and photochemical smog episodes in Shanghai in 2009. The number of haze days accounted for 43%, of which 30% was severe (visibility<2km) and moderate (2km≤visibility<3km) haze, mainly distributed in winter and spring. The mean particle number concentration was about 17,000/cm(3) in haze, more than 2 times that in clean days. The greatest increase of particle number concentration was in 0.5-1μm and 1-10μm size fractions during haze events, about 17.78 times and 8.78 times those of clean days. The largest increase of particle number concentration was within 50-100nm and 100-200nm fractions during photochemical smog episodes, about 5.89 times and 4.29 times those of clean days. The particle volume concentration and surface concentration in haze, photochemical smog and clean days were 102, 49, 15μm(3)/cm(3) and 949, 649, 206μm(2)/cm(3), respectively. As haze events got more severe, the number concentration of particles smaller than 50nm decreased, but the particles of 50-200nm and 0.5-1μm increased. The diurnal variation of particle number concentration showed a bimodal pattern in haze days. All soluble ions were increased during haze events, of which NH4(+), SO4(2-) and NO3(-) increased greatly, followed by Na(+), K(+), Ca(2+) and Cl(-). These ions were very different in size-resolved particles during haze and photochemical smog episodes. PMID:25193840

  16. High aerosol acidity despite declining atmospheric sulfate concentrations over the past 15 years

    NASA Astrophysics Data System (ADS)

    Weber, Rodney J.; Guo, Hongyu; Russell, Armistead G.; Nenes, Athanasios

    2016-04-01

    Particle acidity affects aerosol concentrations, chemical composition and toxicity. Sulfate is often the main acid component of aerosols, and largely determines the acidity of fine particles under 2.5 μm in diameter, PM2.5. Over the past 15 years, atmospheric sulfate concentrations in the southeastern United States have decreased by 70%, whereas ammonia concentrations have been steady. Similar trends are occurring in many regions globally. Aerosol ammonium nitrate concentrations were assumed to increase to compensate for decreasing sulfate, which would result from increasing neutrality. Here we use observed gas and aerosol composition, humidity, and temperature data collected at a rural southeastern US site in June and July 2013 (ref. ), and a thermodynamic model that predicts pH and the gas-particle equilibrium concentrations of inorganic species from the observations to show that PM2.5 at the site is acidic. pH buffering by partitioning of ammonia between the gas and particle phases produced a relatively constant particle pH of 0-2 throughout the 15 years of decreasing atmospheric sulfate concentrations, and little change in particle ammonium nitrate concentrations. We conclude that the reductions in aerosol acidity widely anticipated from sulfur reductions, and expected acidity-related health and climate benefits, are unlikely to occur until atmospheric sulfate concentrations reach near pre-anthropogenic levels.

  17. Influence of crustal dust and sea spray supermicron particle concentrations and acidity on inorganic NO3- aerosol during the 2013 Southern Oxidant and Aerosol Study

    SciTech Connect

    Allen, Hannah M.; Draper, Danielle C.; Ayres, Benjamin R.; Ault, Andrew P.; Bondy, Amy L.; Takahama, S.; Modini, Robert; Baumann, K.; Edgerton, Eric S.; Knote, Christoph; Laskin, Alexander; Wang, Bingbing; Fry, Juliane L.

    2015-09-25

    The inorganic aerosol composition was measured in the southeastern United States, a region that exhibits high aerosol mass loading during the summer, as part of the 1 June to 15 July 2013 Southern Oxidant and Aerosol Study (SOAS) campaign. Measurements using a Monitor for AeRosols and GAses (MARGA), an ion chromatograph coupled with a wet rotating denuder and a steam-jet aerosol collector for monitoring of ambient inorganic gas and aerosol species, revealed two periods of high aerosol nitrate (NO3 ) concentrations during the campaign. These periods of high nitrate were correlated with increased concentrations of coarse mode mineral or sea spray aerosol species, particularly Na+ and Ca2+, and with a shift towards aerosol with larger (1 to 2.5 um) diameters. We suggest this nitrate aerosol forms by multiphase reactions of HNO3 and particles, reactions that are facilitated by transport of mineral dust and sea spray aerosol from a source within the United States. The observed high aerosol acidity prevents the formation of NH4NO3, the inorganic nitrogen species often dominant in fine-mode aerosol at higher pH. Calculation of the rate of the heterogeneous uptake of HNO3 on mineral aerosol supports the conclusion that aerosol NO3 is produced primarily by this process, and is likely limited by the availability of mineral dust surface area. Modeling of NO3 and HNO3 by thermodynamic equilibrium models (ISORROPIA II and E-AIM) reveals the importance of including mineral cations in the southeastern United States to accurately balance ion species and predict gas/aerosol phase partitioning.

  18. Aerosol chemical elemental mass concentration at lower free troposphere

    NASA Astrophysics Data System (ADS)

    do Carmo Freitas, Maria; Dionísio, Isabel; Fialho, Paulo; Barata, Filipe

    2007-08-01

    This paper shows the use of Instrumental neutron activation analysis (INAA) technique to determine elemental masses collected by a seven-wavelength Aethalometer instrument at the summit of Pico mountain in the Azorean archipelago, situated in the Central North Atlantic Ocean. Each sample corresponds to air particulate matter measured continuously for periods of approximately 24 h taken from 14th July 2001 through 14th July 2002. The statistical analysis of the coefficients of correlation between all the elements identified, permitted to establish six groups that could potentially be associated with the type of source responsible for the aerosol sampled in the lower free troposphere at the Azorean archipelago. Calculation of the synoptic back trajectories helped to corroborate the use of the iron/cesium relation as a tracer for the Saharan dust aerosol. It was demonstrated that INAA constituted an important tool to identify these events.

  19. Measured and modelled Cloud Condensation Nuclei (CCN) concentration in São Paulo, Brazil: the importance of aerosol size-resolved chemical composition on CCN concentration prediction

    NASA Astrophysics Data System (ADS)

    Almeida, G. P.; Brito, J.; Morales, C. A.; Andrade, M. F.; Artaxo, P.

    2013-12-01

    Measurements of cloud condensation nuclei (CCN), aerosol size distribution and non-refractory chemical composition were performed from 16 to 31 October 2012 in the São Paulo Metropolitan Area (SPMA), Brazil. CCN measurements were performed at 0.2%, 0.4%, 0.6%, 0.8% and 1.0% water supersaturation and were subsequently compared with Köhler theory, considering the chemical composition. Real-time chemical composition has been obtained deploying for the first time in SPMA an Aerosol Chemical Ionization Monitor (ACSM). CCN closure analyses were performed considering internal mixture. Average aerosol composition during the studied period yielded 4.81 ± 3.05, 3.26 ± 2.10, 0.30 ± 0.27, 0.52 ± 0.32, 0.37 ± 0.21 and 0.04 ± 0.04 μg m-3 for organics, BC, NH4, SO4, NO3 and Cl, respectively. Particle number concentration was 12 813 ± 5350 cm-3, being a large fraction in the nucleation mode. CCN concentrations were on average 1090 ± 328 cm-3 and 3570 ± 1695 cm-3 at SS = 0.2% and SS = 1.0%, respectively. Results show an increase in aerosol hygroscopicity in the afternoon as a result of aerosol photochemical processing, leading to an enhancement of both organic and inorganic secondary aerosols in the atmosphere, as well as an increase in aerosol average diameter. Considering the bulk composition alone, CCN concentrations were substantially overpredicted (29.6 ± 45.1% at 0.2% supersaturation and 57.3 ± 30.0% at 1.0% supersaturation). Overall, the impact of composition on the calculated NCCN decreases with decreasing supersaturation, partially because using bulk composition introduces less bias for large diameters and lower critical supersaturations. Results suggest that the consideration of only inorganic fraction improves the calculated NCCN. Introducing a size-dependent chemical composition based on filter measurements from previous campaigns has considerably improved simulated values for NCCN (average overprediction error 3.0 ± 33.4% at 0.20% supersaturation and

  20. Relationship of ground-level aerosol concentration and atmospheric electric field at three observation sites in the Arctic, Antarctic and Europe

    NASA Astrophysics Data System (ADS)

    Kubicki, Marek; Odzimek, Anna; Neska, Mariusz

    2016-09-01

    Aerosol number concentrations in the particle size range from ~ 10 nm to 1 μm and vertical electric field strength in the surface layer was measured between September 2012 and December 2013 at three observation sites: mid-latitude station Swider, Poland, and, for the first time, in Hornsund in the Arctic, Spitsbergen, and the Antarctic Arctowski station in the South Shetland Islands. The measurements of aerosol concentrations have been performed simultaneously with measurements of the electric field with the aim to assess the local effect of aerosol on the electric field Ez near the ground at the three stations which at present form a network of atmospheric electricity observatories. Measurements have been made regardless of weather conditions at Swider and Arctowski station and mostly on fair-weather days at Hornsund station. The monthly mean particle number concentrations varied between 580 and 2100 particles cm- 3 at Arctowski, between 90 and 1270 particles cm- 3 in Hornsund, and between 6700 and 14,000 particles cm- 3 in the middle latitude station Swider. Average diurnal variations of the ground-level electric field Ez and particle number concentrations in fair-weather conditions were independent of each other for Arctowski and Hornsund stations. At Swider station the diurnal variation is usually characterized by an increase of aerosol concentration in the evening which results in the increased electric field. The assumption of neglecting the influence of varying aerosol concentration on the variation of the electric field in the polar regions, often adopted in studies, is confirmed here by the observations at Arctowski and Hornsund. The results of aerosol observations are also compared with modelled aerosol concentrations for global atmospheric electric circuit models.

  1. The Role of Atmospheric Aerosol Concentration on Deep Convective Precipitation: Cloud-resolving Model Simulations

    NASA Technical Reports Server (NTRS)

    Tao, W.-K.; Li, X.; Khain, A.; Mastsui, T.; Lang, S.; Simpson, J.

    2007-01-01

    Aerosols and especially their effect on clouds are one of the key components of the climate system and the hydrological cycle [Ramanathan et al., 20011. Yet, the aerosol effect on clouds remains largely unknown and the processes involved not well understood. A recent report published by the National Academy of Science states "The greatest uncertainty about the aerosol climate forcing - indeed, the largest of all the uncertainties about global climate forcing - is probably the indirect effect of aerosols on clouds NRC [2001]." The aerosol effect on clouds is often categorized into the traditional "first indirect (i.e., Twomey)" effect on the cloud droplet sizes for a constant liquid water path and the "semi-direct" effect on cloud coverage. The aerosol effect on precipitation processes, also known as the second type of aerosol indirect effect, is even more complex, especially for mixed-phase convective clouds. ln this paper, a cloud-resolving model (CRM) with detailed spectral-bin microphysics was used to examine the effect of aerosols on three different deep convective cloud systems that developed in different geographic locations: South Florida, Oklahoma and the Central Pacific. In all three cases, rain reaches the ground earlier for the low CCN (clean) case. Rain suppression is also evident in all three cases with high CCN (dirty) case. However, this suppression only occurs during the first hour of the simulations. During the mature stages of the simulations, the effects of increasing aerosol concentration range from rain suppression in the Oklahoma case, to almost no effect in the Florida case, to rain enhancement in the Pacific case. These results show the complexity of aerosol interactions with convection.

  2. Emission Controls Versus Meteorological Conditions in Determining Aerosol Concentrations in Beijing during the 2008 Olympic Games

    SciTech Connect

    Gao, Yi; Liu, Xiaohong; Zhao, Chun; Zhang, Meigen

    2011-12-12

    A series of emission control measures were undertaken in Beijing and the adjacent provinces in China during the 2008 Beijing Olympic Games on August 8th-24th, 2008. This provides a unique opportunity for investigating the effectiveness of emission controls on air pollution in Beijing. We conducted a series of numerical experiments over East Asia for the period of July to September 2008 using a coupled meteorology-chemistry model (WRF-Chem). Model can generally reproduce the observed variation of aerosol concentrations. Consistent with observations, modeled concentrations of aerosol species (sulfate, nitrate, ammonium, black carbon, organic carbon, total particulate matter) in Beijing were decreased by 30-50% during the Olympic period compared to the other periods in July and August in 2008 and the same period in 2007. Model results indicate that emission controls were effective in reducing the aerosol concentrations by comparing simulations with and without emission controls. However, our analysis suggests that meteorological conditions (e.g., wind direction and precipitation) are at least as important as emission controls in producing the low aerosol concentrations appearing during the Olympic period. Transport from the regions surrounding Beijing determines the temporal variation of aerosol concentrations in Beijing. Based on the budget analysis, we suggest that emission control strategy should focus on the regional scale instead of the local scale to improve the air quality over Beijing.

  3. Emission controls versus meteorological conditions in determining aerosol concentrations in Beijing during the 2008 Olympic Games

    NASA Astrophysics Data System (ADS)

    Gao, Y.; Liu, X.; Zhao, C.; Zhang, M.

    2011-12-01

    A series of emission control measures were undertaken in Beijing and the adjacent provinces in China during the 2008 Beijing Olympic Games on 8-24 August 2008. This provides a unique opportunity for investigating the effectiveness of emission controls on air pollution in Beijing. We conducted a series of numerical experiments over East Asia for the period of July to September 2008 using a coupled meteorology-chemistry model (WRF-Chem). Model can generally reproduce the observed variation of aerosol concentrations. Consistent with observations, modeled concentrations of aerosol species (sulfate, nitrate, ammonium, black carbon, organic carbon, total particulate matter) in Beijing were decreased by 30-50% during the Olympic period compared to the other periods in July and August in 2008 and the same period in 2007. Model results indicate that emission controls were effective in reducing the aerosol concentrations by comparing simulations with and without emission controls. In addition to emission controls, our analysis suggests that meteorological conditions (e.g. wind direction and precipitation) were also important in producing the low aerosol concentrations appearing during the Olympic period. Transport from the regions surrounding Beijing determined the daily variation of aerosol concentrations in Beijing. Based on the budget analysis, we suggest that to improve the air quality over Beijing, emission control strategy should focus on the regional scale instead of the local scale.

  4. Mobile measurements of aerosol number and volume size distributions in an Alpine valley: Influence of traffic versus wood burning

    NASA Astrophysics Data System (ADS)

    Weimer, S.; Mohr, C.; Richter, R.; Keller, J.; Mohr, M.; Prévôt, A. S. H.; Baltensperger, U.

    The spatial variability of highly time resolved size distributions was investigated in a narrow valley which provides the opportunity to study the impact of different sources on ambient particle concentrations during summer and winter time. The measurements were performed with a Fast Mobility Particle Sizer (FMPS) from TSI, Inc. on a mobile laboratory in Southern Switzerland. The results indicate enhanced number concentrations (between 150 000 and 500 000 cm -3) along the busy highway A2 which is the main transit route through the Swiss Alps connecting the northern and southern part of Switzerland. Especially the nanoparticles with diameters lower than 30 nm showed strongly increased number concentrations on the highway both in summer and winter. In winter time, high aerosol volume concentrations (PM 0.3) were found in villages where wood burning is often used for heating purposes. Both traffic and wood burning were found to be important sources for particulate mass which accumulates during temperature inversions in winter time. Traffic was the dominant and wood burning a minor source for the nanoparticle number concentration. This is important regarding health impacts and its attribution to different sources because wood burning might contribute most to particulate mass whereas at the same time and place traffic contributes most to particulate number. In addition, during summer time volatility measurements were performed with the FMPS showing that the nucleation mode prevalently seen on the highway was removed by more than 95% by thermal treatment.

  5. AGRICULTURAL AMMONIA EMISSIONS AND AMMONIUM CONCENTRATIONS ASSOCIATED WITH AEROSOLS AND PRECIPITATION IN THE SOUTHEAST UNITED STATES

    EPA Science Inventory

    Temporal and spatial variations in ammonia (NH3) emissions and ammonium (NH4+) concentrations associated with aerosols and volume-weighted NH4+ concentration in precipitation are investigated over the period 1990-1998 in the southeast United States (Alabama, Florida, Georgia, Ken...

  6. Impacts of interannual variation of the East Asian winter monsoon on aerosol concentrations over eastern China

    NASA Astrophysics Data System (ADS)

    Zhu, J.; Liao, H.; Li, J.; Feng, J.

    2012-04-01

    China has been experiencing increased concentrations of aerosols, commonly attributed to the large increases in emissions associated with the rapid economic development. We apply a global three-dimensional Goddard Earth Observing System chemical transport model (GEOS-Chem) driven by the NASA/GEOS-4 assimilated meteorological data to quantify the impacts of East Asian winter monsoon (EAWM) on the aerosol concentrations over eastern China. We found that the simulated aerosol concentrations over eastern China have strong interannual variation and negative correlations with the strength of EAWM. Model results show that, accounting for sulfate, nitrate, ammonium, black carbon, and organic carbon aerosols, the winter surface layer PM2.5 concentration averaged over eastern China (110°-125°E, 20°-45°N) can be 17.97% (4.78 µg m-3) higher in the weak monsoon years than that in the strong monsoon years. Regionally, the weakening of EAWM is shown to be able to increase PM2.5 concentration in the middle and lower reach of the Yellow River by 12 µg m-3. This point indicates that climate change associated with variation of EAWM has an essential influence on worsening air quality over eastern China. The possible causes of higher aerosol concentrations in the weak monsoon years may be attributed to the changing in wind fields and planetary boundary layer height between the weak and strong monsoon years. Sensitivity studies are performed to identify the role of chemical reaction associated with temperature and humidity on the higher aerosol concentrations in the weak monsoon years over eastern China.

  7. Thyroid CT number and its relationship to iodine concentration

    SciTech Connect

    Iida, Y.; Konishi, J.; Harioka, T.; Misaki, T.; Endo, K.; Torizuka, K.

    1983-06-01

    Sixty-seven patients with thyroid disease and 24 normal controls were examined with computed tomography (CT). The mean CT number (Hounsfield units +/- SD) in the normal controls (118.1 +/- 12.2) was significantly higher (p < 0.001) than the mean CT number in patients with diseased thyroids, except for 2 cases of simple goiter (CT numbers 113, 132). The Graves disease (69.5 +/- 17.6) amd Hishimoto thyroiditis (61.4 +/- 9.1) were significaantly higher than those in patients with adenoma (41.7 +/- 10.6, p < 0.001), cyst (33.1 +/- 14.8, p < 0.001), or cancer (48.7 +/- 13, p < 0.01). In 14 patients studied, a significant correlation was observed between thyroid CT numbers and the iodine concentration of the tissue (r = 0.889; p < 0.001).

  8. Characterization of ultrafine particle number concentration and new particle formation in urban environment of Taipei, Taiwan

    NASA Astrophysics Data System (ADS)

    Cheung, H. C.; Chou, C. C.-K.; Huang, W.-R.; Tsai, C.-Y.

    2013-04-01

    An intensive aerosol characterization experiment was performed at the Taipei Aerosol and Radiation Observatory (TARO, 25.02° N, 121.53° E) in the urban area of Taipei, Taiwan during July 2012. Number concentration and size distribution of aerosol particles were measured continuously, which were accompanied by concurrent measurements of mass concentration of submicron particles, PM (d ≤ 1 μm), and photolysis rate of ozone, J(O1D). The averaged number concentrations of total (Ntotal), accumulation mode (Nacu), Aitken mode (Ntotal), and nucleation mode (Nnuc) particles were 7.6 × 103 cm-3, 1.2 × 103 cm-3, 4.4 × 103 cm-3, and 1.9 × 103 cm-3, respectively. Accordingly, the ultrafine particles (UFPs, d ≤ 100 nm) accounted for 83% of the total number concentration of particles measured in this study (10 ≤ d ≤ 429 nm), indicating the importance of UFPs to the air quality and radiation budget in Taipei and its surrounding areas. An averaged Nnuc/NOx ratio of ~60 cm-3 ppbv-1 was derived from nighttime measurements, which was suggested to be the characteristic of vehicle emissions that contributed to the "urban background" of nucleation mode particles throughout a day. On the contrary, it was found that the number concentration of nucleation mode particles was independent of NOx and could be elevated up to 10 times the "urban background" levels during daytime, suggesting a substantial amount of nucleation mode particles produced from photochemical processes. Consistency in the time series of the nucleation mode particle concentration and the proxy of H2SO4 production, UVB·SO2, for new particle formation (NPF) events showed that photo-oxidation of SO2 was responsible for the formation of new particles in our study area. Moreover, analysis upon the diameter growth rate, GR, and formation rate of nucleation mode particles, J10-25, found that the values of GR (8.5 ± 6.8 nm h-1) in Taipei were comparable to other urban areas, whereas the values of J10-25 (2.2 ± 1

  9. Aerosol- and updraft-limited regimes of cloud droplet formation: influence of particle number, size and hygroscopicity on the activation of cloud condensation nuclei (CCN)

    NASA Astrophysics Data System (ADS)

    Reutter, P.; Su, H.; Trentmann, J.; Simmel, M.; Rose, D.; Gunthe, S. S.; Wernli, H.; Andreae, M. O.; Pöschl, U.

    2009-09-01

    We have investigated the formation of cloud droplets under pyro-convective conditions using a cloud parcel model with detailed spectral microphysics and with the κ-Köhler model approach for efficient and realistic description of the cloud condensation nucleus (CCN) activity of aerosol particles. Assuming a typical biomass burning aerosol size distribution (accumulation mode centred at 120 nm), we have calculated initial cloud droplet number concentrations (NCD) for a wide range of updraft velocities (w=0.25-20 m s-1) and aerosol particle number concentrations (NCN=200-105 cm-3) at the cloud base. Depending on the ratio between updraft velocity and particle number concentration (w/NCN), we found three distinctly different regimes of CCN activation and cloud droplet formation: (1) An aerosol-limited regime that is characterized by high w/NCN ratios (>≈10-3 m s-1 cm3), high maximum values of water vapour supersaturation (Smax>≈0.5%), and high activated fractions of aerosol particles (NCN/NCN>≈90%). In this regime NCD is directly proportional to NCN and practically independent of w. (2) An updraft-limited regime that is characterized by low w/NCN ratios (<≈10-4 m s-1 cm3), low maximum values of water vapour supersaturation (Smax<≈0.2%), and low activated fractions of aerosol particles (NCD/NCN<≈20%). In this regime NCD is directly proportional to w and practically independent of NCN. (3) An aerosol- and updraft-sensitive regime (transitional regime), which is characterized by parameter values in between the two other regimes and covers most of the conditions relevant for pyro-convection. In this regime NCD depends non-linearly on both NCN and w. In sensitivity studies we have tested the influence of aerosol particle size distribution and hygroscopicity on NCD. Within the range of effective hygroscopicity parameters that is characteristic for continental atmospheric aerosols (κ≈0.05-0.6), we found that NCD depends rather weakly on the actual value of κ

  10. Ambient aerosol concentrations of sugars and sugar-alcohols at four different sites in Norway

    NASA Astrophysics Data System (ADS)

    Yttri, K. E.; Dye, C.; Kiss, G.

    2007-04-01

    Sugars and sugar-alcohols are demonstrated to be important constituents of the ambient aerosol water-soluble organic carbon fraction (WSOC), and to be tracers for primary biological aerosol particles (PBAP). In the present study, levels of four sugars (fructose, glucose, sucrose, trehalose) and three sugar-alcohols (arabitol, inositol, mannitol) in ambient aerosols have been quantified using a novel HPLC/HRMS-TOF (High Performance Liquid Chromatography in combination with High Resolution Mass Spectrometry - Time of Flight) method to assess the contribution of PBAP to PM10 and PM2.5. Samples were collected at four sites in Norway at different times of the year in order to reflect the various contributing sources and the spatial and seasonal variation of the selected compounds. Sugars and sugar-alcohols were present at all sites investigated, underlining the ubiquity of these highly polar organic compounds. The highest concentrations were reported for sucrose, reaching a maximum concentration of 320 ng m-3 in PM10 and 55 ng m-3 in PM2.5. The mean concentration of sucrose was up to 10 times higher than fructose, glucose and trehalose. The mean concentrations of the sugar-alcohols were typically lower, or equal, to that of the monomeric sugars and trehalose. Peak concentrations of arabitol and mannitol did not exceed 30 ng m-3 in PM10, and for PM2.5 all concentrations were below 6 ng m-3. Sugars and sugar-alcohols were associated primarily with coarse aerosols except during wintertime at the suburban site in Elverum, where a shift towards sub micron aerosols was observed. It is proposed that this shift was due to the intensive use of wood burning for residential heating at this site during winter, confirmed by high concurrent concentrations of levoglucosan. Elevated concentrations of sugars in PM2.5 were observed during spring and early summer at the rural background site Birkenes. It is hypothesized that this was due to ruptured pollen.

  11. The dependence of ice microphysics on aerosol concentration in arctic mixed-phase stratus clouds during ISDAC and M-PACE

    SciTech Connect

    Jackson, Robert C.; McFarquhar, Greg; Korolev, Alexei; Earle, Michael; Liu, Peter S.; Lawson, R. P.; Brooks, Sarah D.; Wolde, Mengistu; Laskin, Alexander; Freer, Matthew

    2012-08-14

    Cloud and aerosol data acquired by the National Research Council of Canada (NRC) Convair-580 aircraft in, above, and below single-layer arctic stratocumulus cloud during the Indirect and Semi-Direct Aerosol Campaign (ISDAC) in April 2008 were used to test three aerosol indirect effects hypothesized to act in mixed-phase clouds: the riming indirect effect, the glaciation indirect effect, and the cold second indirect effect. The data showed a correlation of R= 0.75 between liquid drop number concentration, Nliq, inside cloud and ambient aerosol number concentration NPCASP below cloud. This, combined with increasing liquid water content LWC with height above cloud base and the nearly constant profile of Nliq, suggested that liquid drops were nucleated from aerosol at cloud base. No strong evidence of a riming indirect effect was observed, but a strong correlation of R = 0.69 between ice crystal number concentration Ni and NPCASP above cloud was noted. Increases in ice nuclei (IN) concentration with NPCASP above cloud combined with the subadiabatic LWC profiles suggest possible mixing of IN from cloud top consistent with the glaciation indirect effect. The higher Nice and lower effective radius rel for the more polluted ISDAC cases compared to data collected in cleaner single-layer stratocumulus conditions during the Mixed-Phase Arctic Cloud Experiment is consistent with the operation of the cold second indirect effect. However, more data in a wider variety of meteorological and surface conditions, with greater variations in aerosol forcing, are required to identify the dominant aerosol forcing mechanisms in mixed-phase arctic clouds.

  12. Sensitivity of warm-frontal processes to cloud-nucleating aerosol concentrations

    NASA Technical Reports Server (NTRS)

    Igel, Adele L.; Van Den Heever, Susan C.; Naud, Catherine M.; Saleeby, Stephen M.; Posselt, Derek J.

    2013-01-01

    An extratropical cyclone that crossed the United States on 9-11 April 2009 was successfully simulated at high resolution (3-km horizontal grid spacing) using the Colorado State University Regional Atmospheric Modeling System. The sensitivity of the associated warm front to increasing pollution levels was then explored by conducting the same experiment with three different background profiles of cloud-nucleating aerosol concentration. To the authors' knowledge, no study has examined the indirect effects of aerosols on warm fronts. The budgets of ice, cloud water, and rain in the simulation with the lowest aerosol concentrations were examined. The ice mass was found to be produced in equal amounts through vapor deposition and riming, and the melting of ice produced approximately 75% of the total rain. Conversion of cloud water to rain accounted for the other 25%. When cloud-nucleating aerosol concentrations were increased, significant changes were seen in the budget terms, but total precipitation remained relatively constant. Vapor deposition onto ice increased, but riming of cloud water decreased such that there was only a small change in the total ice production and hence there was no significant change in melting. These responses can be understood in terms of a buffering effect in which smaller cloud droplets in the mixed-phase region lead to both an enhanced vapor deposition and decreased riming efficiency with increasing aerosol concentrations. Overall, while large changes were seen in the microphysical structure of the frontal cloud, cloud-nucleating aerosols had little impact on the precipitation production of the warm front.

  13. Time evolution of atmospheric particle number concentration during high-intensity pyrotechnic events

    NASA Astrophysics Data System (ADS)

    Crespo, Javier; Yubero, Eduardo; Nicolás, Jose F.; Caballero, Sandra; Galindo, Nuria

    2014-10-01

    The Mascletàs are high-intensity pyrotechnic events, typical of eastern Spanish festivals, in which thousands of firecrackers are burnt at ground level in an intense, short-time (<8 min) deafening spectacle that generates short-lived, thick aerosol clouds. In this study, the impact of such events on air quality has been evaluated by means of particle number concentration measurements performed close to the venue during the June festival in Alicante (southeastern Spain). Peak concentrations and dilution times observed throughout the Mascletàs have been compared to those measured when conventional aerial fireworks were launched 2 km away from the monitoring site. The impact of the Mascletàs on the total number concentration of particles larger than 0.3 μm was higher (maximum ˜2·104 cm-3) than that of fireworks (maximum ˜2·103 cm-3). The effect of fireworks depended on whether the dominant meteorological conditions favoured the transport of the plume to the measurement location. However, the time required for particle concentrations to return to background levels is longer and more variable for firework displays (minutes to hours) than for the Mascletàs (<25 min).

  14. Estimation of multiple-aerosol concentration and backscatter using multi-wavelength range-resolved lidar

    NASA Astrophysics Data System (ADS)

    Warren, Russell E.; Vanderbeek, Richard G.

    2007-09-01

    Previous work by the authors has produced statistically based methods for detecting, estimating and classifying aerosol materials in the atmosphere using multiple-wavelength range-resolved CO2 lidar. This work has thus far been limited to the presence of a single aerosol material at a given time within the lidar line-of-sight. Practical implementation requires the ability to detect and discriminate multiple aerosol materials present simultaneously such as smoke and dust in addition to hazardous materials. Treating mixtures of materials necessitates fundamentally different approaches from the single-material case since neither the aerosol backscatter wavelength-dependence nor the concentrations as a function of range are known. Because of this, linear processing cannot resolve the mixture data into its components unambiguously, and non-linear methods must be considered. In this paper we describe an empirical Bayes (EB) approach for resolving mixtures of aerosol into their components. The basic idea of EB is to use the same data to estimate the prior distribution of a set of parameters as that used to estimate the parameters themselves. In our case the concentration and backscatter are the parameters that are estimated with the help of a prior distribution of the backscatter. We implement the EB estimator through the EM (Expectation Maximization) algorithm. The resulting processor is applied to injections of interferent dust into data sets collected by ECBC during JBSDS testing at Dugway Proving Ground, UT in 2006.

  15. Mass concentration and mineralogical characteristics of aerosol particles collected at Dunhuang during ACE-Asia

    NASA Astrophysics Data System (ADS)

    Shen, Z. X.; Cao, J. J.; Li, X. X.; Okuda, T.; Wang, Y. Q.; Zhang, X. Y.

    2006-03-01

    Measurements were performed in spring 2001 and 2002 to determine the characteristics of soil dust in the Chinese desert region of Dunhuang, one of the ground sites of the Asia-Pacific Regional Aerosol Characterization Experiment (ACE-Asia). The mean mass concentrations of total suspended particle matter during the spring of 2001 and 2002 were 317 mu g m(-3) and 307 mu g m(-3) respectively. Eleven dust storm events were observed with a mean aerosol concentration of 1095 mu g m(-3), while the non-dusty days with calm or weak wind speed had a background aerosol loading of 196 mu g m(-3) on average in the springtime. The main minerals detected in the aerosol samples by X-ray diffraction were illite, kaolinite, chlorite, quartz, feldspar, calcite and dolomite. Gypsum, halite and amphibole were also detected in a few samples. The mineralogical data also show that Asian dust is characterized by a kaolinite to chlorite (K/C) ratio lower than 1 whereas Saharan dust exhibits a K/C ratio larger than 2. Air mass back- trajectory analysis show that three families of pathways are associated with the aerosol particle transport to Dunhuang, but these have similar K/C ratios, which further demonstrates that the mineralogical characteristics of Asian dust are different from African dust.

  16. Assessment of aerosol's mass concentrations from measured linear particle depolarization ratio (vertically resolved) and simulations

    NASA Astrophysics Data System (ADS)

    Nemuc, A.; Vasilescu, J.; Talianu, C.; Belegante, L.; Nicolae, D.

    2013-11-01

    Multi-wavelength depolarization Raman lidar measurements from Magurele, Romania are used in this study along with simulated mass-extinction efficiencies to calculate the mass concentration profiles of different atmospheric components, due to their different depolarization contribution to the 532 nm backscatter coefficient. Linear particle depolarization ratio (δpart) was computed using the relative amplification factor and the system-dependent molecular depolarization. The low depolarizing component was considered as urban/smoke, with a mean δpart of 3%, while for the high depolarizing component (mineral dust) a mean δpart of 35% was assumed. For this study 11 months of lidar measurements were analysed. Two study cases are presented in details: one for a typical Saharan dust aerosol intrusion, 10 June 2012 and one for 12 July 2012 when a lofted layer consisting of biomass burning smoke extended from 3 to 4.5 km height. Optical Properties of Aerosols and Clouds software package (OPAC) classification and conversion factors were used to calculate mass concentrations. We found that calibrated depolarization measurements are critical in distinguishing between smoke-reach aerosol during the winter and dust-reach aerosol during the summer, as well as between elevated aerosol layers having different origins. Good agreement was found between lidar retrievals and DREAM- Dust REgional Atmospheric Model forecasts in cases of Saharan dust. Our method was also compared against LIRIC (The Lidar/Radiometer Inversion Code) and very small differences were observed.

  17. Assessment of aerosol's mass concentrations from measured linear particle depolarization ratio (vertically resolved) and simulations

    NASA Astrophysics Data System (ADS)

    Nemuc, A.; Vasilescu, J.; Talianu, C.; Belegante, L.; Nicolae, D.

    2013-06-01

    Multiwavelength depolarization Raman lidar measurements from Magurele, Romania are used in this study along with simulated mass-extinction efficiencies to calculate the mass concentrations profiles of different atmospheric components, due to their different depolarization contribution to the 532 nm backscatter coefficient. Linear particle depolarization ratio (δpart) was computed using the relative amplification factor and the system-dependent molecular depolarization. The low depolarizing component was considered as urban/smoke, with a mean δpart of 3%, while for the high depolarizing component (mineral dust) a mean δpart of 35% was assumed. For this study 11 months of lidar measurements were analyzed. Two study cases are presented in details: one for a typical Saharan dust aerosol intrusion, 10 June 2012 and one for 12 July 2012 when a lofted layer consisting of biomass burning smoke extended from 3 to 4.5 km height. Optical Properties of Aerosols and Clouds software package (OPAC) classification and conversion factors were used to calculate mass concentrations. We found that calibrated depolarization measurements are critical to distinguish between smoke-reach aerosol during the winter and dust-reach aerosol during the summer, as well as between elevated aerosol layers having different origins. Good agreement was found between lidar retrievals and DREAM- Dust REgional Atmospheric Model forecasts in cases of Saharan dust. Our method was also compared against LIRIC (The Lidar/Radiometer Inversion Code) and very small differences were observed.

  18. Preferential concentration of certain elements in smaller aerosols emitted from aircraft engines

    NASA Technical Reports Server (NTRS)

    Jolly, R. K.; Gupta, S. K.; Randers-Pehrson, G.; Buckle, D. C.; Thornton, W. B.; Aceto, H., Jr.; Singh, J. J.; Woods, D. C.

    1975-01-01

    Aerosols from aircraft engines were collected with an eight-stage cascade sampler for a period of 24 h. The aerosol samples from each stage were analyzed for their elemental composition using the proton-induced X-ray emission (PIXE) technique. Seventeen elements (Si, P, S, Cl, K, Ca, Ti, V, Fe, Ni, Cu, Zn, Br, Sr, Nb, Sn, and Pb) were positively identified and quantitated at each stage. Six elements (S, Ca, Fe, Zn, Sn, and Pb) showed a fractional concentration increase with decreasing aerosol size. Similar, but less well-defined, trends were also observed for V and Ni. Silicon and chlorine, on the other hand, showed an opposite trend. Neutron-activation analysis of bulk aerosol samples collected every 2 h over the same period showed a correlation between concentration of Si, Ca, V, Ti, Zn, Br, and Sn and the density of air traffic at the airport. Analysis of the aviation-fuel samples by PIXE indicates that major fractions of Pb, Sn, Br, Zn, Ni, Fe, V, Ca, and S observed in these aerosol studies come from the aircraft engine exhaust.

  19. AEROSOL CONCENTRATIONS DURING THE 1999 FRESNO EXPOSURE STUDIES AS FUNCTIONS OF SIZE, SEASON, AND METEOROLOGY

    EPA Science Inventory

    The 1999 Fresno exposure studies took place in February (winter season) and April/May (spring season) for two periods of four weeks. During that time, nearly-continuous measurements of outdoor aerosol concentrations were made with a scanning mobility spectrometer (TSI SNIPS) an...

  20. Comparison of two methods for obtaining quantitative mass concentrations from aerosol time-of-flight mass spectrometry measurements.

    PubMed

    Qin, Xueying; Bhave, Prakash V; Prather, Kimberly A

    2006-09-01

    Aerosol time-of-flight mass spectrometry (ATOFMS) measurements provide continuous information on the aerodynamic size and chemical composition of individual particles. In this work, we compare two approaches for converting unscaled ATOFMS measurements into quantitative particle mass concentrations using (1) reference mass concentrations from a co-located micro-orifice uniform deposit impactor (MOUDI) with an accurate estimate of instrument busy time and (2) reference number concentrations from a co-located aerodynamic particle sizer (APS). Aerodynamic-diameter-dependent scaling factors are used for both methods to account for particle transmission efficiencies through the ATOFMS inlet. Scaling with APS data retains the high-resolution characteristics of the ambient aerosol because the scaling functions are specific for each hourly time period and account for a maximum in the ATOFMS transmission efficiency curve for larger-sized particles. Scaled mass concentrations obtained from both methods are compared with co-located PM(2.5) measurements for evaluation purposes. When compared against mass concentrations from a beta attenuation monitor (BAM), the MOUDI-scaled ATOFMS mass concentrations show correlations of 0.79 at Fresno, and the APS-scaled results show correlations of 0.91 at Angiola. Applying composition-dependent density corrections leads to a slope of nearly 1 with 0 intercept between the APS-scaled absolute mass concentration values and BAM mass measurements. This paper provides details on the methodologies used to convert ATOFMS data into continuous, quantitative, and size-resolved mass concentrations that will ultimately be used to provide a quantitative estimate of the number and mass concentrations of particles from different sources. PMID:16944899

  1. Sensitivity studies of the effect of increased aerosol concentrations and snow crystal shape on the snowfall rate in the Arctic

    NASA Astrophysics Data System (ADS)

    Lohmann, U.; Zhang, J.; Pi, J.

    2003-06-01

    The mesoscale model GESIMA is used to simulate microphysical properties of Arctic clouds and their effect on radiation. Different case studies during the FIRE ACE/SHEBA project show that GESIMA is able to simulate the cloud boundaries, ice and liquid water content, and effective radii in good agreement with observations. For two different aerosol scenarios, the simulation results show that the anthropogenic aerosol can alter microphysical properties of Arctic clouds, and consequently modify surface precipitation. [2000] proposed that anthropogenically induced decreases in cloud droplet size inhibit the riming process. On the contrary, we find that the accretion of snow crystals with cloud droplets is increased in the polluted cloud owing to its higher cloud droplet number concentration. Instead, the autoconversion rate of cloud droplets and accretion of drizzle by snow decreases caused by the shutdown of the collision-coalescence process in the polluted cloud. The amount of precipitation reaching the surface as snow depends crucially on the crystal shape. If aggregates are assumed, then a tenfold increase in aerosol concentration leads to an increase in accumulated snow by 40% after 7 hours of simulation whereas the snow amount decreases by 30% when planar crystals are assumed because of the larger accretion efficiency of snow crystals with cloud droplets in case of aggregates.

  2. The Role of Atmospheric Aerosol Concentration on Deep Convective Precipitation: Cloud-Resolving Model Simulations

    NASA Technical Reports Server (NTRS)

    Tao, Wei-Kuo; Li, Xiaowen; Khain, Alexander; Matsui, Toshihisa; Lang, Stephen; Simpson, Joanne

    2010-01-01

    Aerosols and especially their effect on clouds are one of the key components of the climate system and the hydrological cycle [Ramanathan et al., 2001]. Yet, the aerosol effect on clouds remains largely unknown and the processes involved not well understood. A recent report published by the National Academy of Science states "The greatest uncertainty about the aerosol climate forcing - indeed, the largest of all the uncertainties about global climate forcing - is probably the indirect effect of aerosols on clouds NRC [2001]." The aerosol effect on Clouds is often categorized into the traditional "first indirect (i.e., Twomey)" effect on the cloud droplet sizes for a constant liquid water path and the "semi-direct" effect on cloud coverage. The aerosol effect on precipitation processes, also known as the second type of aerosol indirect effect, is even more complex, especially for mixed-phase convective clouds. In this paper, a cloud-resolving model (CRM) with detailed spectral-bin microphysics was used to examine the effect of aerosols on three different deep convective cloud systems that developed in different geographic locations: South Florida, Oklahoma and the Central Pacific, In all three cases, rain reaches the ground earlier for the low CCN (clean) case. Rain suppression is also evident in all three cases with high CCN (dirty) case. However, this suppression only occurs during the first hour of the simulations. During the mature stages of the simulations, the effects of increasing aerosol concentration range from rain suppression in the Oklahoma case, to almost no effect in the Florida case, to rain enhancement in the Pacific case. These results show the complexity of aerosol interactions with convection. The model results suggest that evaporative cooling is a key process in determining whether high CCN reduces or enhances precipitation. Stronger evaporative cooling can produce a stronger cold pool and thus stronger low-level convergence through interactions

  3. Vapor-phase concentrations of PAHs and their derivatives determined in a large city: correlations with their atmospheric aerosol concentrations.

    PubMed

    Barrado, Ana Isabel; García, Susana; Sevillano, Marisa Luisa; Rodríguez, Jose Antonio; Barrado, Enrique

    2013-11-01

    Thirteen PAHs, five nitro-PAHs and two hydroxy-PAHs were determined in 55 vapor-phase samples collected in a suburban area of a large city (Madrid, Spain), from January 2008 to February 2009. The data obtained revealed correlations between the concentrations of these compounds and a series of meteorological factors (e.g., temperature, atmospheric pressure) and physical-chemical factors (e.g., nitrogen and sulfur oxides). As a consequence, seasonal trends were observed in the atmospheric pollutants. A "mean sample" for the 14-month period would contain a total PAH concentration of 13835±1625 pg m(-3) and 122±17 pg m(-3) of nitro-PAHs. When the data were stratified by season, it emerged that a representative sample of the coldest months would contain 18900±2140 pg m(-3) of PAHs and 150±97 pg m(-3) of nitro-PAHs, while in an average sample collected in the warmest months, these values drop to 9293±1178 pg m(-3) for the PAHs and to 97±13 pg m(-3) for the nitro-PAHs. Total vapor phase concentrations of PAHs were one order of magnitude higher than concentrations detected in atmospheric aerosol samples collected on the same dates. Total nitro-PAH concentrations were comparable to their aerosol concentrations whereas vapor phase OH-PAHs were below their limits of the detection, indicating these were trapped in airborne particles. PMID:23816454

  4. Estimating the backscatter spectral dependence and relative concentration for multiple aerosol materials from lidar data

    NASA Astrophysics Data System (ADS)

    Warren, Russell E.; Vanderbeek, Richard G.

    2004-08-01

    Detection and estimation of materials in the atmosphere by lidar has heretofore required that the spectral dependence of the relevant cross section coefficients -- backscatter in the case of aerosols and absorptivity for vapors -- be known in advance. While this typically is a reasonable assumption in the case of vapor, the aerosol backscatter coefficients are complicated functions of particle size, shape, and refractive index, and are therefore usually not well characterized a priori. Using incorrect parameters will give biased concentration estimates and impair discrimination ability. This paper describes an approach for estimating both the spectral dependence of the aerosol backscatter and relative concentration range-dependence of a set of materials using multi-wavelength lidar. The approach is based on state-space filtering that applies a Kalman filter in range for concentration, and updates the backscatter spectral estimates through a sequential least-squares algorithm at each time step. The method is illustrated on aerosol-release data of the bio-simulant ovalbumin collected by ECBC during field tests in 2002, as well as synthetic data sets.

  5. Black Carbon Concentration from Worldwide Aerosol Robotic Network (AERONET) Measurements

    NASA Technical Reports Server (NTRS)

    Schuster, Gregory L.; Dubovik, Oleg; Holben, Brent N.; Clothiaux, Eugene E.

    2006-01-01

    The carbon emissions inventories used to initialize transport models and general circulation models are highly parameterized, and created on the basis of multiple sparse datasets (such as fuel use inventories and emission factors). The resulting inventories are uncertain by at least a factor of 2, and this uncertainty is carried forward to the model output. [Bond et al., 1998, Bond et al., 2004, Cooke et al., 1999, Streets et al., 2001] Worldwide black carbon concentration measurements are needed to assess the efficacy of the carbon emissions inventory and transport model output on a continuous basis.

  6. Fire and biofuel contributions to annual mean aerosol mass concentrations in the United States

    NASA Astrophysics Data System (ADS)

    Park, Rokjin J.; Jacob, Daniel J.; Logan, Jennifer A.

    We estimate the contributions from biomass burning (summer wildfires, other fires, residential biofuel, and industrial biofuel) to seasonal and annual aerosol concentrations in the United States. Our approach is to use total carbonaceous (TC) and non-soil potassium (ns-K) aerosol mass concentrations for 2001-2004 from the nationwide IMPROVE network of surface sites, together with satellite fire data. We find that summer wildfires largely drive the observed interannual variability of TC aerosol concentrations in the United States. TC/ns-K mass enhancement ratios from fires range from 10 for grassland and shrub fires in the south to 130 for forest fires in the north. The resulting summer wildfire contributions to annual TC aerosol concentrations for 2001-2004 are 0.26 μg C m -3 in the west and 0.14 μg C m -3 in the east; Canadian fires are a major contributor in the east. Non-summer wildfires and prescribed burns contribute on an annual mean basis 0.27 and 0.31 μg C m -3 in the west and the east, highest in the southeast because of prescribed burning. Residential biofuel is a large contributor in the northeast with annual mean concentration of up to 2.2 μg C m -3 in Maine. Industrial biofuel (mainly paper and pulp mills) contributes up to 0.3 μg C m -3 in the southeast. Total annual mean fine aerosol concentrations from biomass burning average 1.2 and 1.6 μg m -3 in the west and east, respectively, contributing about 50% of observed annual mean TC concentrations in both regions and accounting for 30% (west) and 20% (east) of total observed fine aerosol concentrations. Our analysis supports bottom-up source estimates for the contiguous United States of 0.7-0.9 Tg C yr -1 from open fires (climatological) and 0.4 Tg C yr -1 from biofuel use. Biomass burning is thus an important contributor to US air quality degradation, which is likely to grow in the future.

  7. A High Performance Liquid Chromatography Method for Determination of Levoglucosan Concentrations in Atmospheric Aerosols

    NASA Astrophysics Data System (ADS)

    Dixon, R. W.; Baltzell, G.

    2002-12-01

    Levoglucosan (1,6-anhydro-β-D-glucopyranose) recently has been measured in atmospheric aerosols where it is a major organic compound originating from biomass combustion. Past analysis methods have used gas chromatography with and without derivitization. We have developed a method for analyzing levoglucosan in atmospheric aerosols using high peformance liquid chromatography (HPLC) with a new detection method called aerosol charge detection. In aerosol charge detection, the column effluent is converted to an aerosol that is charged by passage near a corona discharge region and detected by charge collection. A column specific for carbohydrate compounds, which separates compounds by ligand-exchange and by partitioning based on polarity, was used for the separation using a 100% water eluent at 60°C. Under these conditions, aerosol filter samples extracted in methanol and water gave peaks with the same retention time as a levoglucosan standard. The detection limit was estimated to be about 0.1 μg mL-1 for extracts or 5 to 10 ng m-3 for air sample volumes employed. Samples collected at locations in central New Mexico and central California were found to contain concentrations of levoglucosan from the detection limit to 270 ng m-3, with higher concentrations observed under colder conditions when more fireplaces would tend to be in use. Mannosan (1,6-anhydro-β-D-mannopyranose), another monosaccharide anhydride, also was observed in one sample. The presence of other organic compounds, which have not yet been identified, was inferred by other observed peaks and by an increased baseline in sample chromatograms.

  8. Number concentrations of fine and ultrafine particles containing metals

    NASA Astrophysics Data System (ADS)

    Tolocka, Michael P.; Lake, Derek A.; Johnston, Murray V.; Wexler, Anthony S.

    Typical classification schemes for large data sets of single-particle mass spectra involve statistical or neural network analysis. In this work, a new approach is evaluated in which particle spectra are pre-selected on the basis of an above threshold signal intensity at a specified m/ z (mass to charge ratio). This provides a simple way to identify candidate particles that may contain the specific chemical component associated with that m/ z. Once selected, the candidate particle spectra are then classified by the fast adaptive resonance algorithm, ART 2-a, to confirm the presence of the targeted component in the particle and to study the intra-particle associations with other chemical components. This approach is used to characterize metals in a 75,000 particle data set obtained in Baltimore, Maryland. Particles containing a specific metal are identified and then used to determine the size distribution, number concentration, time/wind dependencies and intra-particle correlations with other metals. Four representative elements are considered in this study: vanadium, iron, arsenic and lead. Number concentrations of ambient particles containing these elements can exceed 10,000 particles cm -3 at the measurement site. Vanadium, a primary marker for fuel oil combustion, is observed from all wind directions during this time period. Iron and lead are observed from the east-northeast. Most particles from this direction that contain iron also contain lead and most particles that contain lead also contain iron, suggesting a common emission source for the two. Arsenic and lead are observed from the south-southeast. Particles from this direction contain either arsenic or lead but rarely both, suggesting different sources for each element.

  9. Aerosol particle and organic vapor concentrations at industrial work sites in Malaysia.

    PubMed

    Armstrong, R W; Rood, M J; Sani, S; Mohamed, M; Rashid, M; Jab, A T; Landsberger, S

    2001-01-01

    The objective of this study was to establish baseline data about air pollutants potentially related to nasopharyngeal carcinoma (NPC) in the Federal Territory and Selangor, Malaysia. During 1991-1993, ambient air quality was monitored at 42 work sites representing ten industrial sectors: adhesive manufacturing, foundries, latex processing, metalworking, plywood/veneer milling, ricemilling, rubber tire manufacturing, sawmilling, shoemaking, and textile related industries. At each work site, aerosol particle size distributions and concentrations of formaldehyde, benzene, toluene, isopropyl alcohol, and furfural were measured. Mean aerosol particle concentrations ranged from 61 micrograms/m3 in foundries to 5,578 micrograms/m3 in ricemills, with five industries (adhesives, metalworking, ricemilling, sawmilling, and shoemaking) exceeding the US EPA 24-hr ambient air standard for PM-10. Formaldehyde concentrations exceeded the threshold limit value (TLV) in adhesives factories. Other vapours and elements measured were well below TLVs. PMID:12109256

  10. Simulations of organic aerosol concentrations during springtime in the Guanzhong Basin, China

    NASA Astrophysics Data System (ADS)

    Feng, Tian; Li, Guohui; Cao, Junji; Bei, Naifang; Shen, Zhenxing; Zhou, Weijian; Liu, Suixin; Zhang, Ting; Wang, Yichen; Huang, Ru-jin; Tie, Xuexi; Molina, Luisa T.

    2016-08-01

    The organic aerosol (OA) concentration is simulated in the Guanzhong Basin, China from 23 to 25 April 2013 utilizing the WRF-CHEM model. Two approaches are used to predict OA concentrations: (1) a traditional secondary organic aerosol (SOA) module; (2) a non-traditional SOA module including the volatility basis-set modeling method in which primary organic aerosol (POA) is assumed to be semivolatile and photochemically reactive. Generally, the spatial patterns and temporal variations of the calculated hourly near-surface ozone and fine particle matters agree well with the observations in Xi'an and surrounding areas. The model also yields reasonable distributions of daily PM2.5 and elemental carbon (EC) compared to the filter measurements at 29 sites in the basin. Filter-measured organic carbon (OC) and EC are used to evaluate OA, POA, and SOA using the OC / EC ratio approach. Compared with the traditional SOA module, the non-traditional module significantly improves SOA simulations and explains about 88 % of the observed SOA concentration. Oxidation and partitioning of POA treated as semivolatile constitute the most important pathway for the SOA formation, contributing more than 75 % of the SOA concentrations in the basin. Residential emissions are the dominant anthropogenic OA source, constituting about 50 % of OA concentrations in urban and rural areas and 30 % in the background area. The OA contribution from transportation emissions decreases from 25 % in urban areas to 20 % in the background area, and the industry emission OA contribution is less than 6 %.

  11. The contribution of sub-grid, plume-scale nucleation to global and regional aerosol and CCN concentrations

    NASA Astrophysics Data System (ADS)

    Stevens, R.; Pierce, J. R.

    2013-12-01

    New-particle formation in the plumes of coal-fired power plants and other anthropogenic sulphur sources may be an important source of particles in the atmosphere. It has been unclear, however, how best to reproduce this formation in global and regional aerosol models with grid-box lengths that are 10s of kilometres and larger. The predictive power of these models is thus limited by the resultant uncertainties in aerosol size distributions. Based on the results of the System for Atmospheric Modelling (SAM), a Large-Eddy Simulation/Cloud-Resolving Model (LES/CRM) with online TwO Moment Aerosol Sectional (TOMAS) microphysics, we develop the Predicting Particles Produced in Power-Plant Plumes (P6) parameterization: a computationally-efficient, but physically-based, parameterization that predicts the characteristics of aerosol formed within sulphur-rich plumes based on parameters commonly available in global- and regional-scale models. Given large-scale mean meteorological parameters, emissions from the source, the desired distance from the source, and the mean background SO2, NOx, and condensation sink, the parameterization will predict the fraction of the emitted SO2 that is oxidized to H2SO4, the fraction of that H2SO4 that forms new particles instead of condensing onto preexisting particles, the median diameter of the newly-formed particles, and the number of newly-formed particles per kilogram SO2 emitted. We implement the P6 parameterization in the GEOS-Chem global chemical-transport model in order to evaluate the contributions of coal-fired power plants globally to particle number and CCN concentrations.

  12. Simulating gas and aerosol concentrations in the Paris area using different land surface models

    NASA Astrophysics Data System (ADS)

    Khvorostyanov, Dmitry; Menut, Laurent; Dupont, Jean-Charles; Morille, Yoann; Haeffelin, Martial

    2010-05-01

    Regional air quality forecasting depends on the performance of weather forecast models used to drive chemistry-transport models. The widely used Weather Research and Forecasting (WRF) model provides a few land surface schemes (LSMs) to compute heat and moisture fluxes over land surface. The LSMs differ in complexity and approaches used. We performed WRF simulations for 15 and 5 km resolution nested domains over the North of France and Paris, respectively, for summer 2008. We used the four LSMs provided with WRF: 6-layer Rapid Update Cycle (RUC), 5-layer thermal diffusion, 2-layer Pleim-Xiu scheme (together with the Pleim-Xiu surface layer and the ACM boundary layer models), and 4-layer Noah scheme. The SIRTA atmospheric observatory located in Paris area provides in situ data of measurements for a number of meteorological parameters, as well as vertical profiles measured by a lidar. The simulation results were compared to the SIRTA measurement data. In order to quantify possible impacts of the LSMs to simulated gas and aerosol concentrations in the Paris region, we use a chemistry-transport model CHIMERE forced by the corresponding WRF meteorological fields. Implications for the regional air quality forecasting will be discussed.

  13. Precipitation effects on aerosol concentration in the background EMEP station of Zarra (Valencia), Spain

    NASA Astrophysics Data System (ADS)

    Calvo, Ana Isabel; San Martín, Isabel; Castro, Amaya; Alonso-Blanco, Elisabeth; Alves, Célia; Duarte, Márcio; Fernández-González, Sergio; Fraile, Roberto

    2014-05-01

    Aerosols and precipitation are closely related, presenting a bidirectional influence and constituting an important source of uncertainties on climate change studies. However, they are usually studied independently and in general are only linked to one another for the development or validation of cloud models. The primary and secondary pollutants may be removed by wet and dry deposition. Wet deposition, including in-cloud and below-cloud scavenging processes, can efficiently remove atmospheric aerosols and it is considered a critical process for determining aerosol concentrations in the atmosphere. In this study, aerosols and precipitation data from a background Spanish EMEP (Cooperative Programme for the Monitoring and Evaluation of Long Range Transmission of Air Pollutants in Europe) station located in Zarra, Valencia (Spain) were analyzed (1° 06' W and 39° 05' N, 885 m asl). The effect of precipitation on aerosol concentration was studied and the correlation between the intensity of precipitation and scavenging effect was investigated. In order to evaluate the effects of precipitation on different aerosol size ranges three different aerosol fractions were studied: PM10, PM10-2.5 and PM2.5. In order to eliminate the influence of the air mass changes, only the days in which the air mass of the precipitation day and the previous day had the same origin were considered. Thus, from a total of 3586 rainy days registered from March 2001 to December 2010, 34 precipitation days satisfied this condition and were analyzed. During the period of study, daily precipitation ranged between 0.2 and 28.8 mm, with a mean value of 4 mm. Regarding the origin of the air masses, those from west were dominant at the three height levels investigated (500, 1500 and 3000 m). In order to obtain additional information, aerosol and precipitation chemical composition were also studied in relation to the days of precipitation and the previous days. Furthermore, in order to identify the type

  14. Aerosol-Radiation Feedback and PM10 Air Concentrations Over Poland

    NASA Astrophysics Data System (ADS)

    Werner, Małgorzata; Kryza, Maciej; Skjøth, Carsten Ambelas; Wałaszek, Kinga; Dore, Anthony J.; Ojrzyńska, Hanna; Kapłon, Jan

    2016-03-01

    We have implemented the WRF-Chem model version 3.5 over Poland to quantify the direct and indirect feedback effects of aerosols on simulated meteorology and aerosol concentrations. Observations were compared with results from three simulations at high spatial resolutions of 5 × 5 km: (1) BASE—without any aerosol feedback effects; (2) DIR—with direct aerosol-radiative effects (3) INDIR—with direct and indirect aerosol-radiative effects. We study the overall effect during January 2011 as well as selected episodes of the highest differences in PM10 concentrations between the three simulations. For the DIR simulation, the decrease in monthly mean incoming solar radiation (SWDOWN) appears for the entire study area. It changes geographically, from about -8.0 to -2.0 W m-2, respectively for the southern and northern parts of the country. The highest changes do not correspond to the highest PM10 concentration. Due to the solar radiation changes, the surface mean monthly temperature (T2) decreases for 96 % of the area of Poland, but not more than 1.0 °C. Monthly mean PBLH changes by more than ±5 m for 53 % of the domain. Locally the differences in PBLH between the DIR and BASE are higher than ± 20 m. Due to the direct effect, for 84 % of the domain, the mean monthly PM10 concentrations increase by up to 1.9 µg m-3. For the INDIR simulation the spatial distribution of changes in incoming solar radiation as well as air temperature is similar to the DIR simulation. The decrease of SWDOWN is noticed for the entire domain and for 23 % of the domain is higher than -5.0 W m-2. The absolute differences of PBLH are slightly higher for INDIR than DIR but similarly distributed spatially. For daily episodes, the differences between the simulations are higher, both for meteorology and PM10 concentrations, and the pattern of changes is usually more complex. The results indicate the potential importance of the aerosol feedback effects on modelled meteorology and PM10

  15. Aerosols and environmental pollution

    NASA Astrophysics Data System (ADS)

    Colbeck, Ian; Lazaridis, Mihalis

    2010-02-01

    The number of publications on atmospheric aerosols has dramatically increased in recent years. This review, predominantly from a European perspective, summarizes the current state of knowledge of the role played by aerosols in environmental pollution and, in addition, highlights gaps in our current knowledge. Aerosol particles are ubiquitous in the Earth’s atmosphere and are central to many environmental issues; ranging from the Earth’s radiative budget to human health. Aerosol size distribution and chemical composition are crucial parameters that determine their dynamics in the atmosphere. Sources of aerosols are both anthropogenic and natural ranging from vehicular emissions to dust resuspension. Ambient concentrations of aerosols are elevated in urban areas with lower values at rural sites. A comprehensive understanding of aerosol ambient characteristics requires a combination of measurements and modeling tools. Legislation for ambient aerosols has been introduced at national and international levels aiming to protect human health and the environment.

  16. Ambient aerosol concentrations of sugars and sugar-alcohols at four different sites in Norway

    NASA Astrophysics Data System (ADS)

    Yttri, K. E.; Dye, C.; Kiss, G.

    2007-08-01

    Sugars and sugar-alcohols are demonstrated to be important constituents of the ambient aerosol water-soluble organic carbon fraction, and to be tracers for primary biological aerosol particles (PBAP). In the present study, levels of four sugars (fructose, glucose, sucrose, trehalose) and three sugar-alcohols (arabitol, inositol, mannitol) in ambient aerosols have been quantified using a novel HPLC/HRMS-TOF (High Performance Liquid Chromatography in combination with High Resolution Mass Spectrometry - Time of Flight) method to assess the contribution of PBAP to PM>sub>10 and PM2.5. Samples were collected at four sites in Norway at different times of the year in order to reflect the various contributing sources and the spatial and seasonal variation of the selected compounds. Sugars and sugar-alcohols were present at all sites investigated, underlining the ubiquity of these highly polar organic compounds. The highest concentrations were reported for sucrose, reaching a maximum concentration of 320 ng m-3 in PM10 and 55 ng m-3 in PM2.5. The mean concentration of sucrose was up to 10 times higher than fructose, glucose and the dimeric sugar trehalose. The mean concentrations of the sugar-alcohols were typically lower, or equal, to that of the monomeric sugars and trehalose. Peak concentrations of arabitol and mannitol did not exceed 30 ng m-3 in PM10, and for PM2.5 all concentrations were below 6 ng m-3. Sugars and sugar-alcohols were associated primarily with coarse aerosols except during wintertime at the suburban site in Elverum, where a shift towards sub micron aerosols was observed. It is proposed that this shift was due to the intensive use of wood burning for residential heating at this site during winter, confirmed by high concurrent concentrations of levoglucosan. Elevated concentrations of sugars in PM2.5 were observed during spring and early summer at the rural background site Birkenes. It is hypothesized that this was due to ruptured pollen.

  17. Time-resolved measurements of aerosol elemental concentrations in indoor working environments

    NASA Astrophysics Data System (ADS)

    Žitnik, M.; Kastelic, A.; Rupnik, Z.; Pelicon, P.; Vaupetič, P.; Bučar, K.; Novak, S.; Samardžija, Z.; Matsuyama, S.; Catella, G.; Ishii, K.

    2010-12-01

    We have measured the elemental concentrations in aerosols with a 2-h time resolution in two different types of working environment: a chemistry laboratory dealing with the processing of advanced nanoparticulate materials and a medium-sized machine workshop. Non-stop 10-day and 12-day samplings were performed at each location in order to determine the concentration trends during the non-working/working and weekday/weekend periods. Supplementary measurements of PM10 aerosols with a 2-day sample collection time were performed with a standard Gent PM10 sampler to compare the elemental concentrations with the time-averaged concentrations detected by the 2D step-sampler. The concentrations were determined a posteriori by analyzing the x-ray spectra of aerosol samples emitted after 3-MeV proton bombardment. The PM10 samples collected in the chemistry laboratory were additionally inspected by scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX) to determine the chemical compositions of the individual particles. In the workshop, a total PM10 mass sampling was performed simultaneously with a minute resolution to compare the signal with typical outdoor PM10 concentration levels. A factor analysis of the time-resolved dataset points to six and eight factors in the chemistry laboratory and the machine workshop, respectively. These factors describe most of the data variance, and their composition in terms of different elements can be related to specific indoor activities and conditions. We were able to demonstrate that the elemental concentration sampling with hourly resolution is an excellent tool for studying the indoor air pollution. While sampling the total PM10 mass concentration with a minute resolution may lack the potential to identify the emission sources in a "noisy" environment, the time averaging on a day time scale is too coarse to cope with the working dynamics, even if elemental sensitivity is an option.

  18. The Aerosol Research and Inhalation Epidemiology Study (ARIES): PM2.5 mass and aerosol component concentrations and sampler intercomparisons.

    PubMed

    Van Loy, M; Bahadori, T; Wyzga, R; Hartsell, B; Edgerton, E

    2000-08-01

    The Aerosol Research and Inhalation Epidemiology Study (ARIES) was designed to provide high-quality measurements of PM2.5, its components, and co-varying pollutants for an air pollution epidemiology study in Atlanta, GA. Air pollution epidemiology studies have typically relied on available data on particle mass often collected using filter-based methods. Filter-based PM2.5 sampling is susceptible to both positive and negative errors in the measurement of aerosol mass and particle-phase component concentrations in the undisturbed atmosphere. These biases are introduced by collection of gas-phase aerosol components on the filter media or by volatilization of particle phase components from collected particles. As part of the ARIES, we collected daily 24-hr PM2.5 mass and speciation samples and continuous PM2.5 data at a mixed residential-light industrial site in Atlanta. These data facilitate analysis of the effects of a wide variety of factors on sampler performance. We assess the relative importance of PM2.5 components and consider associations and potential mechanistic linkages of PM2.5 mass concentrations with several PM2.5 components. For the 12 months of validated data collected to date (August 1, 1998-July 31, 1999), the monthly average Federal Reference Method (FRM) PM2.5 mass always exceeded the proposed annual average standard (12-month average = 20.3 +/- 9.5 micrograms/m3). The particulate SO4(2-) fraction (as (NH4)2SO4) was largest in the summer and exceeded 50% of the FRM mass. The contribution of (NH4)2SO4 to FRM PM2.5 mass dropped to less than 30% in winter. Particulate NO3- collected on a denuded nylon filter averaged 1.1 +/- 0.9 micrograms/m3. Particle-phase organic compounds (as organic carbon x 1.4) measured on a denuded quartz filter sampler averaged 6.4 +/- 3.1 micrograms/m3 (32% of FRM PM2.5 mass) with less seasonal variability than SO4(2-). PMID:11002607

  19. Hillslope soil erosion estimated from aerosol concentrations, North Halawa Valley, Oahu, Hawaii

    USGS Publications Warehouse

    Hill, B.R.; Fuller, C.C.; DeCarlo, E.H.

    1997-01-01

    Concentrations of aerosolic quartz and 137Cs were used to estimate rates of hillslope soil erosion during 1990-91 in the North Halawa Valley on the island of Oahu, Hawaii. Fluvial transport of quartz was estimated to be 6.1 Mg in 1990 and 14.9 Mg in 1991. Fluvial transport of 137Cs from North Halawa Valley was estimated to be 1.29 ?? 109 pCi in 1991. Results were used with quartz contents, 137Cs activities, and bulk densities of hillslope soils to compute rates of basinwide hillslope soil erosion ranging from 0.1 to 0.3 mm yr-1. These rates are within the range of previous estimates of denudation computed for drainage basins on Oahu. The aerosol-concentration approach, therefore, is a useful method for assessing basinwide soil erosion.

  20. The Influence of High Aerosol Concentration on Atmospheric Boundary Layer Temperature Stratification

    SciTech Connect

    Khaykin, M.N.; Kadygrove, E.N.; Golitsyn, G.S.

    2005-03-18

    Investigations of the changing in the atmospheric boundary layer (ABL) radiation balance as cased by natural and anthropogenic reasons is an important topic of the U.S. Department of Energy's Atmospheric Radiation Measurement (ARM) program. The influence of aerosol on temperature stratification of ABL while its concentration was extremely high within a long period of time was studied experimentally. The case was observed in Moscow region (Russia) with the transport of combustion products from peat-bog and forest fires in July-September, 2002. At this time the visibility was some times at about 100-300 m. Aerosol concentration measured by Moscow University Observatory and A.M. Obukhov Institute of Atmospheric Physics field station in Zvenigorod (55.7 N; 36.6 E) for several days was in 50-100 times more than background one (Gorchakov at al 2003). The high aerosol concentration can change the radiation balance at ABL, and so to change thermal stratification in ABL above the mega lopolis. For the analysis the data were used of synchronous measurements by MTP-5 (Microwave Temperature Profiler operating at wavelength 5 mm) in two locations, namely: downtown Moscow and country-side which is 50 km apart to the West (Zvenigorod station). (Kadygrov and Pick 1998; Westwater at al 1999; Kadygrov at al 2002). Zvenigorod station is located in strongly continental climate zone which is in between of the climates of ARM sites (NSANorth Slope of Alaska and SGP-Southern Great Plains). The town of Zvenigorod has little industry, small traffic volume and topography conductive to a good air ventilation of the town. For these reasons Zvenigorod can be considered as an undisturbed rural site. For the analysis some days were chosen with close meteorological parameters (average temperature, humidity, wind, pressure and cloud form) but strongly differing in aerosol concentration level.

  1. Characterization of ultrafine particle number concentration and new particle formation in an urban environment of Taipei, Taiwan

    NASA Astrophysics Data System (ADS)

    Cheung, H. C.; Chou, C. C.-K.; Huang, W.-R.; Tsai, C.-Y.

    2013-09-01

    An intensive aerosol characterization experiment was performed at the Taipei Aerosol and Radiation Observatory (TARO, 25.02° N, 121.53° E) in the urban area of Taipei, Taiwan, during July 2012. Number concentration and size distribution of aerosol particles were measured continuously, which were accompanied by concurrent measurements of mass concentration of submicron particles, PM1 (d ≤ 1 μm), and photolysis rate of ozone, J(O1D). The averaged number concentrations of total (Ntotal), accumulation mode (Nacu), Aitken mode (NAitken), and nucleation mode (Nnuc) particles were 13.9 × 103 cm-3, 1.2 × 103 cm-3, 6.1 × 103 cm-3, and 6.6 × 103 cm-3, respectively. Accordingly, the ultrafine particles (UFPs, d ≤ 100 nm) accounted for 91% of the total number concentration of particles measured in this study (10 ≤ d ≤ 429 nm), indicating the importance of UFPs to the air quality and radiation budget in Taipei and its surrounding areas. An averaged Nnuc / NOx ratio of 192.4 cm-3 ppbv-1 was derived from nighttime measurements, which was suggested to be the characteristic of vehicle emissions that contributed to the "urban background" of nucleation mode particles throughout a day. On the contrary, it was found that the number concentration of nucleation mode particles was independent of NOx and could be elevated up to 10 times of the "urban background" levels during daytime, suggesting a substantial amount of nucleation mode particles produced from photochemical processes. Averages (± 1σ) of the diameter growth rate (GR) and formation rate of nucleation mode particles, J10, were 11.9 ± 10.6 nm h-1 and 6.9 ± 3.0 cm-3 s-1, respectively. Consistency in the time series of the nucleation mode particle concentration and the proxy of H2SO4 production, UVB · SO2/CS, for new particle formation (NPF) events suggested that photooxidation of SO2 was likely one of the major mechanisms for the formation of new particles in our study area. Moreover, it was revealed that the

  2. Influence of a high aerosol concentration on the thermal structure of the atmospheric boundary layer

    NASA Astrophysics Data System (ADS)

    Khaikin, M. N.; Kuznetsova, I. N.; Kadygrov, E. N.

    2006-12-01

    The influence of increased concentrations of submicron aerosol produced by forest fires on thermal characteristics of the atmospheric boundary layer (ABL) in Moscow and its remote vicinity (the town of Zvenigorod) are analyzed on the basis of regular remote measurements of the ABL temperature profile with the use of MTP-5 profilers. In the air basin of a large city, additional aerosol and accompanying pollutants in early morning hours (at small heights of the Sun) most frequently did not cause substantial changes in the ABL thermal structure. In the locality remote from the megalopolis (Zvenigorod), the atmospheric pollution by aerosol led to noticeable changes in the ABL thermal characteristics. Especially strong changes were observed in the daytime, during the maximum supply of solar radiation. In morning hours, the heating rate of the lower 100-m layer of the polluted air exceeded the heating rate of a relatively pure air by more than one degree. In higher layers, the differences between the rates of temperature changes in a relatively clean atmosphere and in an atmosphere polluted by aerosol (in the suburb) were insignificant.

  3. The contribution of secondary organic aerosol to PM2.5 concentrations in Pittsburgh

    NASA Astrophysics Data System (ADS)

    Cabada, J. C.; Pandis, S. N.; Robinson, A. L.; Subramanian, R.; Polidori, A.; Turpin, B.

    2002-12-01

    A major component of PM2.5 in the Eastern US is carbonaceous material. This organic particulate matter results from both direct emissions from sources such as automobiles, trucks and industries (primary), and from the oxidation of organic gases (secondary). Data from the Pittsburgh Air Quality Study are used to examine the contribution of secondary organic aerosol to the total organic aerosol loading measured in the city during 2001 and 2002. The contribution of secondary organic aerosol is estimated by using elemental carbon as a tracer for primary emissions of organic particulate matter (OC to EC ratio approach). A systematic method for the determination of the primary ratio has been developed based on the correlation of measurements of OC and EC to gaseous tracers of photochemical activity (O3) and primary emissions (CO, NOx). This method is applied to different sets of organic aerosols measurements (using an undenuded sampler, a denuded sampler and an in-situ carbon analyzer) for carbonaceous concentrations. Consistent results for the SOA fraction are obtained when the method is applied to the different sets of measurements for OC and EC. This approach indicates that between 20 and 40% of the organic particulate matter in Pittsburgh during the summer and fall of 2001 is secondary in origin while negligible contributions of SOA are estimated for the winter of 2001 and the spring of 2002.

  4. Concentrations and composition of aerosols and particulate matter in surface waters along the transatlantic section

    NASA Astrophysics Data System (ADS)

    Nemirovskaya, I. A.; Lisitzin, A. P.; Novigatsky, A. N.; Redzhepova, Z. U.; Dara, O. M.

    2016-07-01

    Along the transatlantic section from Ushuaia to Gdańsk (March 26-May 7, 2015; cruise 47 of R/V Akademik Ioffe), data were obtained on the concentrations of aerosols in the near-water layer of the atmosphere and of particulate matter in surface waters, as well as of organic compounds within the considered matter (Corg, chlorophyll a, lipids, and hydrocarbons). The concentrations of aerosols amounted to 1237-111 739 particles/L for the fraction of 0.3-1 μm and to 0.02-34.4 μg/m2/day for the matter collected by means of the network procedure. The distribution of aerosols is affected by circumcontinental zoning and by the fluxes from arid areas of African deserts. The maximum concentration of the treated compounds were found in the river-sea frontal area (the runoff of the Colorado River, Argentina), as well as when nearing the coasts, especially in the English Channel.

  5. Fungal Spore Concentrations and Ergosterol Content in Aerosol Samples in the Caribbean During African Dust Events

    NASA Astrophysics Data System (ADS)

    Santos-Figueroa, G.; Bolaños-Rosero, B.; Mayol-Bracero, O. L.

    2015-12-01

    Fungal spores are a major component of primary biogenic aerosol particles that are emitted to the atmosphere, are ubiquitous, and play an important role in the chemistry and physics of the atmosphere, climate, and public health. Every year, during summer months, African dust (AD) particles are transported to the Caribbean region causing an increase in the concentrations of particulate matter in the atmosphere. AD is one of the most important natural sources of mineral particulate matter at the global scale, and many investigations suggest that it has the ability to transport dust-associated biological particles through long distances. The relationship between AD incursions and the concentration of fungal spores in the Caribbean region is poorly understood. In order to investigate the effects of AD incursions on fungal spore's emissions, fungal spore concentrations were monitored using a Burkard spore trap at the tropical montane cloud forest of Pico del Este at El Yunque National Forest, Puerto Rico. The presence of AD was supported with satellite images of aerosol optical thickness, and with the results from the air masses backward trajectories calculated with the NOAA HYSPLIT model. Basidiospores and Ascospores comprised the major components of the total spore's concentrations, up to a maximum of 98%, during both AD incursions and background days. A considerably decrease in the concentration of fungal spores during AD events was observed. Ergosterol, biomarker for measuring fungal biomass, concentrations were determined in aerosols that were sampled at a marine site, Cabezas de San Juan Nature Reserve, in Fajardo Puerto Rico, and at an urban site, Facundo Bueso building at the University of Puerto Rico. Additional efforts to understand the relationship between the arrival of AD to the Caribbean and a decrease in spore's concentrations are needed in order to investigate changes in local spore's vs the contribution of long-range spores transported within the AD.

  6. Final Report, The Influence of Organic-Aerosol Emissions and Aging on Regional and Global Aerosol Size Distributions and the CCN Number Budget

    SciTech Connect

    Donahue, Neil M.

    2015-12-23

    We conducted laboratory experiments and analyzed data on aging of organic aerosol and analysis of field data on volatility and CCN activity. With supplemental ASR funding we participated in the FLAME-IV campaign in Missoula MT in the Fall of 2012, deploying a two-chamber photochemical aging system to enable experimental exploration of photochemical aging of biomass burning emissions. Results from that campaign will lead to numerous publications, including demonstration of photochemical production of Brown Carbon (BrC) from secondary organic aerosol associated with biomass burning emissions as well as extensive characterization of the effect of photochemical aging on the overall concentrations of biomass burning organic aerosol. Excluding publications arising from the FLAME-IV campaign, project research resulted in 8 papers: [11, 5, 3, 10, 12, 4, 8, 7], including on in Nature Geoscience addressing the role of organic compounds in nanoparticle growth [11

  7. Non-spherical aerosol transport under oscillatory shear flows at low-Reynolds numbers

    NASA Astrophysics Data System (ADS)

    Shachar Berman, Lihi; Delorme, Yann; Hofemeier, Philipp; Frankel, Steven; Sznitman, Josue

    2014-11-01

    Most airborne particles are intrinsically non-spherical. In particular, non-spherical particles with high aspect ratios, such as fibers, are acknowledged to be more hazardous than their spherical counterparts due to their ability to penetrate into deeper lung regions, causing serious pulmonary diseases. Not only do particle properties such as size, shape, and density have a major impact on particle transport, for non-spherical aerosols, their orientations also greatly influence particle trajectories due to modified lift and drag characteristics. Until present, however, most of our understanding of the dynamics of inhaled particles in the deep airways of the lungs has been limited to spherical particles only. In the present work, we seek to quantify through numerical simulations the transport of non-spherical airborne particles and their deposition under oscillatory shear flows at low Reynolds numbers, characteristic of acinar airways. Here, the Euler-Lagrangian model is used to solve the translational movement of a fiber, whereas the Eulerian rotational equations are introduced and solved to predict detailed unsteady fiber orientations. Overall, our efforts provide new insight into realistic dynamics of inhaled non-spherical aerosols under characteristic breathing motions.

  8. Carbonaceous aerosols on the south edge of the Tibetan Plateau: concentrations, seasonality and sources

    NASA Astrophysics Data System (ADS)

    Cong, Z.; Kang, S.; Kawamura, K.; Liu, B.; Wan, X.; Wang, Z.; Gao, S.; Fu, P.

    2014-10-01

    To quantitatively evaluate the effect of carbonaceous aerosols on the south edge of the Tibetan Plateau, aerosol samples were collected weekly from August 2009 to July 2010 at Mt. Everest (Qomolangma Station for Atmospheric and Environmental Observation and Research, briefly QOMS, 28.36° N, 86.95° E, 4276 m a.s.l.). The samples were analyzed for organic carbon (OC), elemental carbon (EC), water-soluble organic carbon (WSOC) and major ions. The average concentrations of OC, EC and WSOC were 1.43, 0.25 and 0.77 μg m-3, respectively. The concentration levels of OC and EC at QOMS are comparable to those at high elevation sites on the southern slopes of the Himalayas (Langtang and NCO-P), but three to six times lower than those at Manora Peak, India and Godavari, Nepal. Sulfate was the most abundant anion species followed by nitrate, accounting for 25 and 12% of total ionic mass, respectively. Ca2+ was the most abundant cation species (annual average of 0.88 μg m-3). The various aerosol compositions showed distinctive seasonality. The dust loading, represented by Ca2+ concentration, was relatively constant throughout the year. While OC, EC and other ionic species (NH4+, K+, NO3-, and SO42-) exhibited a pronounced peak in the pre-monsoon period and a minimum in the monsoon season. Similar seasonal trends of aerosol composition were also reported previously from the southern slope of the Himalayas, such as Langtang and NCO-P. This phenomenon indicates that both slopes of Himalayas share a common atmospheric environment regime. The strong correlation of OC and EC in QOMS aerosols with K+ and levoglucosan indicates that they were mainly originated from biomass burning. The active fire spots observed by MODIS and their backward trajectories further demonstrate that in pre-monsoon season, agricultural and forest fires in the northern India and Nepal were most likely sources of carbonaceous aerosol at QOMS. In addition to large-scale atmospheric circulation, the unique

  9. Carbonaceous aerosols on the south edge of the Tibetan Plateau: concentrations, seasonality and sources

    NASA Astrophysics Data System (ADS)

    Cong, Z.; Kang, S.; Kawamura, K.; Liu, B.; Wan, X.; Wang, Z.; Gao, S.; Fu, P.

    2015-02-01

    To quantitatively evaluate the effect of carbonaceous aerosols on the south edge of the Tibetan Plateau, aerosol samples were collected weekly from August 2009 to July 2010 at Qomolangma (Mt. Everest) Station for Atmospheric and Environmental Observation and Research (QOMS, 28.36° N, 86.95° E, 4276 m a.s.l.). The average concentrations of organic carbon (OC), elemental carbon (EC) and water-soluble organic carbon were 1.43, 0.25 and 0.77 μg m-3, respectively. The concentration levels of OC and EC at QOMS are comparable to those at high-elevation sites on the southern slopes of the Himalayas (Langtang and Nepal Climate Observatory at Pyramid, or NCO-P), but 3 to 6 times lower than those at Manora Peak, India, and Godavari, Nepal. Sulfate was the most abundant anion species followed by nitrate, accounting for 25 and 12% of total ionic mass, respectively. Ca2+ was the most abundant cation species (annual average of 0.88 μg m-3). The dust loading, represented by Ca2+ concentration, was relatively constant throughout the year. OC, EC and other ionic species (NH4+, K+, NO3- and SO42-) exhibited a pronounced peak in the pre-monsoon period and a minimum in the monsoon season, being similar to the seasonal trends of aerosol composition reported previously from the southern slope of the Himalayas, such as Langtang and NCO-P. The strong correlation of OC and EC in QOMS aerosols with K+ and levoglucosan indicates that they mainly originated from biomass burning. The fire spots observed by MODIS and backward air-mass trajectories further demonstrate that in pre-monsoon season, agricultural and forest fires in northern India and Nepal were most likely sources of carbonaceous aerosol at QOMS. Moreover, the CALIOP observations confirmed that air-pollution plumes crossed the Himalayas during this period. The highly coherent variation of daily aerosol optical depth (500 nm) between QOMS and NCO-P indicates that both slopes of the Himalayas share a common atmospheric environment

  10. A method for segregating the optical absorption properties and the mass concentration of winter time urban aerosol

    NASA Astrophysics Data System (ADS)

    Ajtai, T.; Utry, N.; Pintér, M.; Major, B.; Bozóki, Z.; Szabó, G.

    2015-12-01

    A novel in-situ, real time method for the determination of inherent absorption properties of light absorbing carbonaceous particulate matter and its possible application for source apportionment are introduced here. The method is deduced from a two-week campaign under wintry urban conditions during which strong correlation was found between aerosol number size distribution and wavelength dependent optical absorption coefficient (AOC(λ)), measured by a Single Mobility Particle Sizer (SMPS) and a multi-wavelength photoacoustic absorption spectrometer, respectively, while wood burning and traffic (i.e. fossil fuel burning) activity were identified to be the dominant sources of carbonaceous particulate. Indeed, during the whole campaign, regardless of the actual emission strength of the aerosol sources, the measured number size distributions were always dominated by two unimodal modes with Count Mean Diameter (CMD) of 20 and 100 nm, which could be correlated to traffic and wood burning activities, respectively. AAEff, AAEwb (i.e. the Aerosol Angström Exponent of traffic and wood burning aerosol, respectively), σff(266 nm), σff(1064 nm), σwb(266 nm) and σff(1064 nm) (i.e. the segregated mass specific optical absorption coefficients at two of the measurement wavelengths) were found to be 1.17 ± 0.18, 2.6 ± 0.14, 7.3 ± 0.3 m2g-1, 1.7 ± 0.1 m2g-1 3.4 ± 0.3 m2g-1 and 0.31 ± 0.08 m2g-1, respectively. Furthermore the introduced methodology can also disentangle and quantify the temporal variation of both the segregated optical absorptions and the segregated mass concentrations of traffic and wood burning aerosol. Accordingly, the contribution of wood burning to optical absorption of PM was found to be negligible at 1064 nm but increased gradually towards the shorter wavelengths and became commensurable with the optical absorption of traffic at 266 nm during the whole measurement period. Furthermore, the contribution of wood burning mass to CM (mass of carbonaceous

  11. MODELING THE EFFECT OF CHLORINE EMISSIONS ON ATMOSPHERIC OZONE AND SECONDARY ORGANIC AEROSOL CONCENTRATIONS ACROSS THE UNITED STATES

    EPA Science Inventory

    This paper presents the modeled effects of natural and anthropogenic chlorine emissions on the atmospheric concentrations of ozone and secondary organic aerosol across the United States. The model calculations include anthropogenic molecular chlorine emissions, anthropogenic hypo...

  12. Future Projections of Aerosol Optical Depth, Radiative Forcing, and Climate Response Due to Declining Aerosol Emissions in the Representative Concentration Pathways

    NASA Astrophysics Data System (ADS)

    Westervelt, D. M.; Mauzerall, D. L.; Horowitz, L. W.; Naik, V.

    2014-12-01

    It is widely expected that global emissions of atmospheric aerosols and their precursors will decrease strongly throughout the remainder of the 21st century, due to emission reduction policies enacted based on human health concerns. However, the resulting decrease in atmospheric aerosol burden will have unintended climate consequences. Since aerosols generally exert a net cooling influence on the climate, their removal will lead to an unmasking of global warming as well as other changes to the climate system. Aerosol and precursor global emissions decrease by as much as 80% by the year 2100, according to projections in four Representative Concentration Pathway (RCP) scenarios. We use the Geophysical Fluid Dynamics Laboratory Climate Model version 3 (GFDL CM3) to simulate future climate over the 21st century with and without aerosol emission changes projected by the RCPs in order to isolate the radiative forcing and climate response due to the aerosol reductions. We find that up to 1 W m-2 of radiative forcing may be unmasked globally by 2100 due to reductions in aerosol and precursor emissions, leading to average global temperature increases up to 1 K and global precipitation rate increases up to 0.09 mm d-1 (3%). Regionally and locally, climate impacts are much larger, as RCP8.5 projects a 2.1 K warming over China, Japan, and Korea due to reduced aerosol emissions. Our results highlight the importance of crafting emissions control policies with both climate and air pollution benefits in mind. The expected unmasking of additional global warming from aerosol reductions highlights the importance of robust greenhouse gas mitigation policies and may require more aggressive policies than anticipated.

  13. A numerical simulation of the effect of the number concentration of cloud droplets on Typhoon Chanchu

    NASA Astrophysics Data System (ADS)

    Lin, Wenshi; Xu, Suishan; Sui, C.-H.

    2011-09-01

    In recent years, an increase in the number of anthropogenic aerosol particles has raised the global mean content of aerosol particles in the atmosphere from that of preindustrial times. The indirect effects of aerosols on weather and climate cannot be ignored. In this paper, the fifth generation Pennsylvania State University (PSU)-National Center of Atmospheric Research (NCAR) Nonhydrostatic Mesoscale Model (MM5) is used to simulate Typhoon Chanchu (international designation: 0601), which affected the northwest Pacific. Simulations are conducted in three two-way nested domains with Mercator map projection. The horizontal grid resolutions of the three domains are 27, 9, and 3 km. A period of 60 h is simulated. Surface and rawinsonde conventional observation data and ocean wind data are additionally incorporated into the initialization data. A control (CTL) experiment is run to produce a reasonable forecast. We change the parameter of the cloud condensation nuclei (CCN) concentration (CNP) in the Reisner-2 scheme of the CTL experiment (the default value is 100 cm-3) to conduct two sensitivity experiments. They are the very clean marine (VCM) CNP experiment (CNP = 25 cm-3) and the severe contamination (SC) CNP experiment (CNP = 1,000 cm-3). We investigate the effects of the CNP on Typhoon Chanchu by comparing and analyzing the simulation results of the three experiments in terms of the track, intensity, precipitation, vertical structure, and microphysical processes. The main results show that Typhoon Chanchu slightly weakens as the CNP increases. Increasing the CCN to 1,000 cm-3 results in less graupel, rainwater, and cloud ice but more cloud water. However, the mixing ratio of snow does not distinctly change as the CNP changes. Increasing the CCN leads a rapid decrease in the autoconversion of cloud water to rainwater. There is no autoconversion of cloud water to rainwater in a seriously polluted continental air mass. As the CNP increases, there is more condensation

  14. Is It Possible to Distinguish Between Dust and Salt Aerosol Over Waters with Unknown Chlorophyll Concentrations Using Spectral Remote Sensing?

    NASA Technical Reports Server (NTRS)

    Levy, R. C.; Kaufman, Y. J.

    1999-01-01

    Atmospheric aerosol has uncertain impacts on the global climate system, as well as on atmospheric and bio-geo-chemical processes of regional and local scales. EOS-MODIS is one example of a satellite sensor designed to improve understanding of the aerosols' type, size and distribution at all temporal and spatial scales. Ocean scientists also plan to use data from EOS-MODIS to assess the temporal and spatial coverage of in-water chlorophyll. MODIS is the first sensor planned to observe the combined ocean-atmosphere system with a wide spectral range (from 410 to 2200 nm). Dust aerosol and salt aerosol have similar spectral signals for wavelengths longer than 550 nm, but because dust selectively absorbs blue light, they have divergent signals in the blue wavelength regions (412 to 490 nm). Chlorophyll also selectively absorbs blue radiation, so that varying chlorophyll concentrations produces a highly varying signal in the blue regions, but less variability in the green, and almost no signal in the red to mid-infrared regions. Thus, theoretically, it may be difficult to differentiate dust and salt in the presence of unknown chlorophyll in the ocean. This study attempts to address the cases in which aerosol and chlorophyll signals can and cannot be separated. For the aerosol spectra, we use the aerosol lookup table from the operational MODIS aerosol-over-ocean algorithm, and for chlorophyll spectra, we use the SeaBAM data set (created for SeaWiFS). We compare the signals using Principal Component Analysis and attempt to retrieve both chlorophyll and aerosol properties using a variant of the operational MODIS aerosol-over-ocean algorithm. Results show that for small optical depths, less than 0.5, it is not possible to differentiate between dust and salt and to determine the chlorophyll concentration at the same time. For larger aerosol optical depths, the chlorophyll signals are comparatively insignificant, and we can hope to distinguish between dust and salt.

  15. Relating Aerosol Profile and Column Measurements to Surface Concentrations: What Have We Learned from Discover-AQ?

    NASA Astrophysics Data System (ADS)

    Hoff, R. M.

    2014-12-01

    One research goal of the Deriving Information on Surface Conditions from COlumn and VERtically Resolved Observations Relevant to Air Quality (DISCOVER-AQ) mission was to determine sufficient column profile measurements to relate column integrated quantities such as Aerosol Optical Depth to surface concentrations. I will review the relationship between AOD and PM2.5 at the surface. DISCOVER-AQ in Baltimore, the San Joaquin Valley, Houston and Denver revealed quite different conditions for determining this relationship. In each case, the surface reflectivity made determination of aerosol optical depth challenging, but upward looking columns of aerosol optical depth from sunphotometers provided confirmation of the AOD results from space. In Baltimore, AOD fields reflected PM2.5 concentrations well. In California, however, the low boundary layer heights and dominance of nitrate and organic aerosols made the AOD fields less predictive of PM2.5. In California and Colorado, hydration of the aerosol varied dramatically with aerosol type (especially smoke and dust) and revealed that without an understanding of the degree of aerosol hydration with aerosol composition, the relationship between AOD and PM2.5 will continue to be a challenge. Model predictions in the Baltimore-Washington study are relatively disappointing in helping define the needed physics between the optical and microphysical properties. An overview of the measurements from DISCOVER-AQ which will help define the needed information in a more general case in the future will be given.

  16. Susceptibility of Tribolium confusum (Coleoptera: Tenebrionidae) to pyrethrin aerosol: effects of aerosol particle size, concentration, and exposure conditions

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A series of laboratory studies were conducted to assess effect of droplet size on efficacy of pyrethrin aerosol against adults of Tribolium confusum Jacqueline DuVal, the confused flour beetle. A vertical flow aerosol exposure chamber that generated a standardized particle size diameter was used for...

  17. Estimation of surface-level PM concentration from satellite observation taking into account the aerosol vertical profiles and hygroscopicity.

    PubMed

    Kim, Kwanchul; Lee, Kwon H; Kim, Ji I; Noh, Youngmin; Shin, Dong H; Shin, Sung K; Lee, Dasom; Kim, Jhoon; Kim, Young J; Song, Chul H

    2016-01-01

    Surface-level PM10 distribution was estimated from the satellite aerosol optical depth (AOD) products, taking the account of vertical profiles and hygroscopicity of aerosols over Jeju, Korea during March 2008 and October 2009. In this study, MODIS AOD data from the Terra and Aqua satellites were corrected with aerosol extinction profiles and relative humidity data. PBLH (Planetary Boundary Layer Height) was determined from MPLNET lidar-derived aerosol extinction coefficient profiles. Through statistical analysis, better agreement in correlation (R = 0.82) between the hourly PM10 concentration and hourly average Sunphotometer AOD was the obtained when vertical fraction method (VFM) considering Haze Layer Height (HLH) and hygroscopic growth factor f(RH) was used. The validity of the derived relationship between satellite AOD and surface PM10 concentration clearly demonstrates that satellite AOD data can be utilized for remote sensing of spatial distribution of regional PM10 concentration. PMID:26421659

  18. Heterogeneous processing of {sup 13}NO{sub 2} at zero concentration by monodisperse carbon aerosols

    SciTech Connect

    Tabor, K.; Kalberer, M.; Parrat, Y.

    1995-12-31

    The heterogeneous chemical processing of atmospheric cases by both natural and anthropogenic aerosols plays a key role in the regional as well as global environment. The oxides of nitrogen in the presence of soot present a particularly interesting and relevant topic covering a wide range of such diverse phenomena as acid rain and stratospheric ozone depletion. Detailed investigations of such systems is difficult due to low aerosol and gas species concentrations and, to date, most studies have investigated the chemistry using bulk samples. Nitrogen dioxide is known to be the most important reactive species in this system proceeding as, NO{sub 2} + (C) {r_arrow} (NO{sub 2}{lg_bullet} C){r_arrow} NO + (O {lg_bullet} C). In our current study, we have used {sup 13}N(T{sub 1/2} = 9.96 min) radioisotope labeling techniques to investigate the uptake and chemical conversion of NO{sub 2} in the presence of monodisperse carbon aerosols under real atmospheric conditions, which represents a significant improvement over earlier studies in our lab. {sup 13}N was produced using 14 MeV protons from the PSI Philips cyclotron and a gas target of 2% O{sub 2} in He for the reaction {sup 16}O(p,{alpha}) {sup 13}N. The resulting {sup 13}NO{sub y} were reduced to {sup 13}NO over molybdenum and subsequently oxidized to {sup 13}NO{sub 2} over CrO{sub 3}. Carbon aerosol was generated by spark discharge between graphite rods in argon. Mono-disperse size cuts were selected with a differential mobility analyzer operated with synthetic air. The NO{sub 2} and aerosol streams were admixed and passed through a reaction volume for a reaction time of 10s. A series of selective traps and one filter were used to separate products and reactants: (1) triethanolamine (TEA) denuder to remove unreacted gas phase NO{sub 2}, (2) TEA impregnated class fiber filter to remove aerosol fraction and NO{sub 2} released after uptake, and (3) Co{sub x}O{sub y} trap to remove all residual NO{sub x}.

  19. A CLOSURE STUDY OF AEROSOL MASS CONCENTRATION MEASUREMENTS: COMPARISON OF VALUES OBTAINED WITH FILTERS AND BY DIRECT MEASUREMENTS OF MASS DISTRIBUTIONS. (R826372)

    EPA Science Inventory

    We compare measurements of aerosol mass concentrations obtained gravimetrically using Teflon coated glass fiber filters and by integrating mass distributions measured with the differential mobility analyzer–aerosol particle mass analyzer (DMA–APM) technique (Aero...

  20. Surface ozone concentration and its behaviour with aerosols in the northwestern Himalaya, India

    NASA Astrophysics Data System (ADS)

    Sharma, Priyanka; Kuniyal, Jagdish Chandra; Chand, Kesar; Guleria, Raj Paul; Dhyani, Pitamber Prasad; Chauhan, Chetan

    2013-06-01

    Surface ozone (O3), black carbon (BC) concentration and their relationship were established with PM10 and PM2.5 mass concentration at Mohal (31.9°N, 77.12°E, 1154 m amsl), a semi-urban site, in the Kullu valley of the northwestern part of the Indian Himalaya during January to December, 2010. O3 showed highest diurnal variation (84 ppb) during daytime and lowest (10 ppb) during late evening as well as early morning hours. The maximum concentration of O3 during summer was influenced by meteorological parameters, high insolation and backward airmass trajectories with transported pollutants. Rate of increase of O3 was observed as high as 2.92 ppb h-1 in October, followed by 2.73 ppb h-1 in March and 2.71 ppb h-1 in May. However, it was low 1.89 ppb h-1 in February. Monthly average concentration of O3 showed distinct seasonal variations with maximum in summer (55.9 ± 9.3 ppb in May) and minimum in winter (30.0 ± 6.2 ppb in January). Most of the O3 episodes were observed in summer during fair weather conditions like high solar flux (480-500 W m-2), relatively high temperature (22-24 °C) and negligible rainfall. By applying backward trajectory Hybrid Single Particle Lagrangian Integrated Trajectory (HYSPLIT) model, the origin of the airmasses contributing to the background O3 concentration was investigated. O3 showed negative correlation with BC (r = -0.42). BC contributed 10-20% and 14-42% to the total aerosol mass concentration of PM10 and PM2.5 respectively which showed positive correlation (r = 0.65) with PM10 as well as PM2.5 aerosol mass concentration.

  1. A single-particle characterization of a mobile Versatile Aerosol Concentration Enrichment System for exposure studies

    PubMed Central

    Freney, Evelyn J; Heal, Mathew R; Donovan, Robert J; Mills, Nicholas L; Donaldson, Kenneth; Newby, David E; Fokkens, Paul HB; Cassee, Flemming R

    2006-01-01

    Background An Aerosol Time-of-Flight Mass Spectrometer (ATOFMS) was used to investigate the size and chemical composition of fine concentrated ambient particles (CAPs) in the size range 0.2–2.6 μm produced by a Versatile Aerosol Concentration Enrichment System (VACES) contained within the Mobile Ambient Particle Concentrator Exposure Laboratory (MAPCEL). The data were collected during a study of human exposure to CAPs, in Edinburgh (UK), in February-March 2004. The air flow prior to, and post, concentration in the VACES was sampled in turn into the ATOFMS, which provides simultaneous size and positive and negative mass spectral data on individual fine particles. Results The particle size distribution was unaltered by the concentrator over the size range 0.2–2.6 μm, with an average enrichment factor during this study of ~5 (after dilution of the final air stream). The mass spectra from single particles were objectively grouped into 20 clusters using the multivariate K-means algorithm and then further grouped manually, according to similarity in composition and time sequence, into 8 main clusters. The particle ensemble was dominated by pure and reacted sea salt and other coarse inorganic dusts (as a consequence of the prevailing maritime-source climatology during the study), with relatively minor contributions from carbonaceous and secondary material. Very minor variations in particle composition were noted pre- and post-particle concentration, but overall there was no evidence of any significant change in particle composition. Conclusion These results confirm, via single particle analysis, the preservation of the size distribution and chemical composition of fine ambient PM in the size range 0.2–2.6 μm after passage through the VACES concentration instrumentation. PMID:16723024

  2. Concentration Effects and Ion Properties Controlling the Fractionation of Halides during Aerosol Formation

    NASA Technical Reports Server (NTRS)

    Guzman, Marcelo I.; Athalye, Richa R.; Rodriguez, Jose M.

    2012-01-01

    During the aerosolization process at the sea surface, halides are incorporated into aerosol droplets, where they may play an important role in tropospheric ozone chemistry. Although this process may significantly contribute to the formation of reactive gas phase molecular halogens, little is known about the environmental factors that control how halides selectively accumulate at the air-water interface. In this study, the production of sea spray aerosol is simulated using electrospray ionization (ESI) of 100 nM equimolar solutions of NaCl, NaBr, NaI, NaNO2, NaNO3, NaClO4, and NaIO4. The microdroplets generated are analyzed by mass spectrometry to study the comparative enrichment of anions (f (Isub x-)) and their correlation with ion properties. Although no correlation exists between f (sub x-) and the limiting equivalent ionic conductivity, the correlation coefficient of the linear fit with the size of the anions R(sub x-), dehydration free-energy ?Gdehyd, and polarizability alpha, follows the order: (R(sub x-)(exp -2)) > (R(sub x-)(exp -1)) >(R(sub x-) > delta G(sub dehyd) > alpha. The same pure physical process is observed in H2O and D2O. The factor f (sub x-) does not change with pH (6.8-8.6), counterion (Li+, Na+, K+, and Cs+) substitution effects, or solvent polarity changes in methanol - and ethanol-water mixtures (0 <= xH2O <= 1). Sodium polysorbate 20 surfactant is used to modify the structure of the interface. Despite the observed enrichment of I- on the air-water interface of equimolar solutions, our results of seawater mimic samples agree with a model in which the interfacial composition is increasingly enriched in I- < Br- < Cl- over the oceanic boundary layer due to concentration effects in sea spray aerosol formation.

  3. Meteorological and trace gas factors affecting the number concentration of atmospheric Aitken (Dp = 50 nm) particles in the continental boundary layer: parameterization using a multivariate mixed effects model

    NASA Astrophysics Data System (ADS)

    Mikkonen, S.; Korhonen, H.; Romakkaniemi, S.; Smith, J. N.; Joutsensaari, J.; Lehtinen, K. E. J.; Hamed, A.; Breider, T. J.; Birmili, W.; Spindler, G.; Plass-Duelmer, C.; Facchini, M. C.; Laaksonen, A.

    2011-01-01

    Measurements of aerosol size distribution and different gas and meteorological parameters, made in three polluted sites in Central and Southern Europe: Po Valley, Italy, Melpitz and Hohenpeissenberg in Germany, were analysed for this study to examine which of the meteorological and trace gas variables affect the number concentration of Aitken (Dp= 50 nm) particles. The aim of our study was to predict the number concentration of 50 nm particles by a combination of in-situ meteorological and gas phase parameters. The statistical model needs to describe, amongst others, the factors affecting the growth of newly formed aerosol particles (below 10 nm) to 50 nm size, but also sources of direct particle emissions in that size range. As the analysis method we used multivariate nonlinear mixed effects model. Hourly averages of gas and meteorological parameters measured at the stations were used as predictor variables; the best predictive model was attained with a combination of relative humidity, new particle formation event probability, temperature, condensation sink and concentrations of SO2, NO2 and ozone. The seasonal variation was also taken into account in the mixed model structure. Model simulations with the Global Model of Aerosol Processes (GLOMAP) indicate that the parameterization can be used as a part of a larger atmospheric model to predict the concentration of climatically active particles. As an additional benefit, the introduced model framework is, in theory, applicable for any kind of measured aerosol parameter.

  4. Meteorological and trace gas factors affecting the number concentration of atmospheric Aitken (Dp=50 nm) particles in the continental boundary layer: parameterization using a multivariate mixed effects model

    NASA Astrophysics Data System (ADS)

    Mikkonen, S.; Korhonen, H.; Romakkaniemi, S.; Smith, J. N.; Joutsensaari, J.; Lehtinen, K. E. J.; Hamed, A.; Breider, T. J.; Birmili, W.; Spindler, G.; Plass-Duelmer, C.; Facchini, M. C.; Laaksonen, A.

    2010-08-01

    Measurements of aerosol size-distribution and different gas and meteorological parameters, made in three polluted sites in Central- and Southern Europe: Po Valley, Italy, Melpitz and Hohenpeissenberg in Germany, were analysed for this study to examine which of the meteorological and trace gas variables affect the number concentration of Aitken (Dp=50 nm) particles. The aim of our study was to predict the number concentration of 50 nm particles by a combination of in-situ meteorological and gas phase parameters. The statistical model needs to describe, amongst others, the factors affecting the growth of newly formed aerosol particles (below 10 nm) to 50 nm size, but also sources of direct particle emissions in that size range. As the analysis method we used multivariate nonlinear mixed effects model. Hourly averages of gas and meteorological parameters measured at the stations were used as predictor variables; the best predictive model was attained with a combination of relative humidity, new particle formation event probability, temperature, condensation sink and concentrations of SO2, NO2 and ozone. The seasonal variation was also taken into account in the mixed model structure. Model simulations with the Global Model of Aerosol Processes (GLOMAP) indicate that the parameterization can be used as a part of a larger atmospheric model to predict the concentration of climatically active particles. As an additional benefit, the introduced model framework is, in theory, applicable for any kind of measured aerosol parameter.

  5. Fluorescent biological aerosol particle concentrations and size distributions measured with an ultraviolet aerodynamic particle sizer (UV-APS) in Central Europe

    NASA Astrophysics Data System (ADS)

    Huffman, J. A.; Treutlein, B.; Pöschl, U.

    2009-08-01

    Primary biological aerosol particles (PBAPs), including bacteria, spores and pollen, are essential for the spread of organisms and disease in the biosphere, and numerous studies have suggested that they may be important for atmospheric processes, including the formation of clouds and precipitation. The atmospheric abundance and size distribution of PBAPs, however, are largely unknown. At a semi-urban site in Mainz, Germany, we used an ultraviolet aerodynamic particle sizer (UV-APS) to measure fluorescent biological aerosol particles (FBAPs), which can be regarded as viable bioaerosol particles representing a lower limit for the actual abundance of PBAPs. Fluorescence of non-biological aerosol components are likely to influence the measurement results obtained for fine particles (<1 μm), but not for coarse particles (1-20 μm). Averaged over the four-month measurement period (August-December 2006), the mean number concentration of coarse FBAPs was ~3×10-2 cm-3, corresponding to ~4% of total coarse particle number. The mean mass concentration of FBAPs was ~1 μg m-3, corresponding to ~20% of total coarse particle mass. The FBAP number size distributions exhibited alternating patterns with peaks at various diameters. A pronounced peak at ~3 μm was essentially always observed and can be described by the following campaign-average lognormal fit parameters: geometric mean diameter 3.2 μm, geometric standard deviation 1.3, number concentration 1.6×10-2 cm-3. This peak is likely due to fungal spores or agglomerated bacteria, and it exhibited a pronounced diel cycle with maximum intensity during early/mid-morning. FBAP peaks around ~1.5 μm, ~5 μm, and ~13 μm were also observed, but less pronounced and less frequent. These may be explained by single bacterial cells, larger fungal spores, and pollen grains, respectively. The observed number concentrations and characteristic sizes of FBAPs are consistent with microscopic, biological and chemical analyses of PBAPs in

  6. Fluorescent Biological Aerosol Particle Concentrations and Size Distributions Measured with an Ultraviolet Aerodynamic Particle Sizer (UV-APS) in Central Europe

    NASA Astrophysics Data System (ADS)

    Huffman, J. A.; Treutlein, B.; Pöschl, U.

    2009-12-01

    Primary biological aerosol particles (PBAPs), including bacteria, spores and pollen, are essential for the spread of organisms and disease in the biosphere, and numerous studies have suggested that they may be important for atmospheric processes, including the formation of clouds and precipitation. The atmospheric abundance and size distribution of PBAPs, however, are largely unknown. At a semi-urban site in Mainz, Germany, we used an ultraviolet aerodynamic particle sizer (UV-APS) to measure fluorescent biological aerosol particles (FBAPs), which can be regarded as viable bioaerosol particles representing a lower limit for the actual abundance of PBAPs. Fluorescence of non-biological aerosol components are likely to influence the measurement results obtained for fine particles (< 1 µm), but not for coarse particles (1 - 20 µm). Averaged over the four-month measurement period (August - December 2006), the mean number concentration of coarse FBAPs was ~3x10-2 cm-3, corresponding to ~4% of total coarse particle number [1]. The mean mass concentration of FBAPs was ~1 µg m-3, corresponding to ~20% of total coarse particle mass. The FBAP number size distributions exhibited alternating patterns with peaks at various diameters. A pronounced peak at ~3 µm was essentially always observed and can be described by the following campaign-average lognormal fit parameters: geometric mean diameter 3.2 µm, geometric standard deviation 1.3, number concentration 1.6 x 10-2 cm-3. This peak is likely due to fungal spores or agglomerated bacteria, and it exhibited a pronounced diel cycle with maximum intensity during early/mid-morning. FBAP peaks around ~1.5 µm, ~5 µm, and ~13 µm were also observed, but less pronounced and less frequent. These may be explained by single bacterial cells, larger fungal spores, and pollen grains, respectively. The observed number concentrations and characteristic sizes of FBAPs are consistent with microscopic, biological and chemical analyses of

  7. Fluorescent biological aerosol particle concentrations and size distributions measured with an Ultraviolet Aerodynamic Particle Sizer (UV-APS) in Central Europe

    NASA Astrophysics Data System (ADS)

    Huffman, J. A.; Treutlein, B.; Pöschl, U.

    2010-04-01

    Primary Biological Aerosol Particles (PBAPs), including bacteria, spores and pollen, are essential for the spread of organisms and disease in the biosphere, and numerous studies have suggested that they may be important for atmospheric processes, including the formation of clouds and precipitation. The atmospheric abundance and size distribution of PBAPs, however, are largely unknown. At a semi-urban site in Mainz, Germany we used an Ultraviolet Aerodynamic Particle Sizer (UV-APS) to measure Fluorescent Biological Aerosol Particles (FBAPs), which provide an estimate of viable bioaerosol particles and can be regarded as an approximate lower limit for the actual abundance of PBAPs. Fluorescence of non-biological aerosol components are likely to influence the measurement results obtained for fine particles (<1 μm), but not for coarse particles (1-20 μm). Averaged over the four-month measurement period (August-December 2006), the mean number concentration of coarse FBAPs was ~3×10-2 cm-3, corresponding to ~4% of total coarse particle number. The mean mass concentration of FBAPs was ~1μg m-3, corresponding to ~20% of total coarse particle mass. The FBAP number size distributions exhibited alternating patterns with peaks at various diameters. A pronounced peak at ~3 μm was essentially always observed and can be described by the following campaign-average lognormal fit parameters: geometric mean diameter 3.2 μm, geometric standard deviation 1.3, number concentration 1.6×10-2 cm-3. This peak is likely due to fungal spores or agglomerated bacteria, and it exhibited a pronounced diel cycle (24-h) with maximum intensity during early/mid-morning. FBAP peaks around ~1.5 μm, ~5 μm, and ~13 μm were also observed, but less pronounced and less frequent. These may be single bacterial cells, larger fungal spores, and pollen grains, respectively. The observed number concentrations and characteristic sizes of FBAPs are consistent with microscopic, biological and chemical

  8. Influence of methane concentration on the optical indices of Titan’s aerosols analogues

    NASA Astrophysics Data System (ADS)

    Mahjoub, A.; Carrasco, N.; Dahoo, P.-R.; Gautier, T.; Szopa, C.; Cernogora, G.

    2012-11-01

    This work deals with the optical constant characterization of Titan aerosol analogues or “tholins” produced with the PAMPRE experimental setup and deposited as thin films onto a silicon substrate. Tholins were produced in different N2-CH4 gaseous mixtures to study the effect of the initial methane concentration on their optical constants. The real (n) and imaginary (k) parts of the complex refractive index were determined using the spectroscopic ellipsometry technique in the 370-1000 nm wavelength range. We found that optical constants depend strongly on the methane concentrations of the gas phase in which tholins are produced: imaginary optical index (k) decreases with initial CH4 concentration from 2.3 × 10-2 down to 2.7 × 10-3 at 1000 nm wavelength, while the real optical index (n) increases from 1.48 up to 1.58 at 1000 nm wavelength. The larger absorption in the visible range of tholins produced at lower methane percentage is explained by an increase of the secondary and primary amines signature in the mid-IR absorption. Comparison with results of other tholins and data from Titan observations are presented. We found an agreement between our values obtained with 10% methane concentration, and Imanaka et al. (Imanaka, H., Khare, B.N., Elsila, J.E., Bakes, E.L.O., McKay, C.P., Cruikshank, D.P., Sugita, S., Matsui, T., Zare, R.N. [2004]. Icarus, 168, 344-366) values, in spite of the difference in the analytical method. This confirms a reliability of the optical properties of tholins prepared with various setups but with similar plasma conditions. Our comparison with Titan’s observations also raises a possible inconsistency between the mid-IR aerosol signature by VIMS and CIRS Cassini instruments and the visible Huygens-DISR derived data. The mid-IR VIMS and CIRS signatures are in agreement with an aerosol dominated by an aliphatic carbon content, whereas the important visible absorption derived from the DISR measurement seems to be incompatible with such

  9. Characterisation of sub-micron particle number concentrations and formation events in the western Bushveld Igneous Complex, South Africa

    NASA Astrophysics Data System (ADS)

    Hirsikko, A.; Vakkari, V.; Tiitta, P.; Manninen, H. E.; Gagné, S.; Laakso, H.; Kulmala, M.; Mirme, A.; Mirme, S.; Mabaso, D.; Beukes, J. P.; Laakso, L.

    2012-05-01

    South Africa holds significant mineral resources, with a substantial fraction of these reserves occurring and being processed in a large geological structure termed the Bushveld Igneous Complex (BIC). The area is also highly populated by informal, semi-formal and formal residential developments. However, knowledge of air quality and research related to the atmosphere is still very limited in the area. In order to investigate the characteristics and processes affecting sub-micron particle number concentrations and formation events, air ion and aerosol particle size distributions and number concentrations, together with meteorological parameters, trace gases and particulate matter (PM) were measured for over two years at Marikana in the heart of the western BIC. The observations showed that trace gas (i.e. SO2, NOx, CO) and black carbon concentrations were relatively high, but in general within the limits of local air quality standards. The area was characterised by very high condensation sink due to background aerosol particles, PM10 and O3 concentration. The results indicated that high amounts of Aitken and accumulation mode particles originated from domestic burning for heating and cooking in the morning and evening, while during daytime SO2-based nucleation followed by the growth by condensation of vapours from industrial, residential and natural sources was the most probable source for large number concentrations of nucleation and Aitken mode particles. Nucleation event day frequency was extremely high, i.e. 86% of the analysed days, which to the knowledge of the authors is the highest frequency ever reported. The air mass back trajectory and wind direction analyses showed that the secondary particle formation was influenced both by local and regional pollution and vapour sources. Therefore, our observation of the annual cycle and magnitude of the particle formation and growth rates during nucleation events were similar to results previously published for a semi

  10. Long-Term Observations on Aerosol Elemental Carbon and Mass Concentrations in Winter-Time in New Delhi: Implications for Local Source Changes

    NASA Astrophysics Data System (ADS)

    Aggarwal, S. G.; Singh, K.; Singh, N.; Gupta, P. K.

    2009-12-01

    Fossil-fuel and bio-fuel burning are the two major sources identified for high carbonaceous aerosol loadings in several mega cities in India. In the last decade, according to a report from the Central Pollution Control Board (CPCB, 1999), the vehicular emission (mostly diesel-powered engines) was contributed to ~67% of the total air pollution load in New Delhi. Therefore, a policy decision was taken by the government, and most of the diesel-powered engines were converted to compressed natural gas (CNG) -powered engines by 2003. To better understand the effect of these changes on air quality, we collected high volume aerosol samples (total suspended particles, TSP) mostly for a day basis at our institute building in New Delhi almost everyday during winter season (November to January) from 2002 to 2008. We found very high mean aerosol loading, i.e., 488±47 μg m-3 in 2002 winter, which dropped significantly to 280±73 μg m-3 in 2003 winter. Thereafter, a steadily increased trend of aerosol mass loadings was observed, i.e., 339±112, 339±120, 412±107 and 444±55 μg m-3 in 2004, 2005, 2006 and 2007 winters, respectively. Similar trend was also observed for elemental carbon (EC) concentration in TSP, which was peaked in 2002 (47±11 μg m-3) and minimized in 2003 (32±6 μg m-3), and then gradually increased to 41±8 μg m-3 in 2007 winter. These decline trends of aerosol mass and EC concentrations in 2003 can be explained well, because of the conversion of diesel engine to CNG engines of public transport facilities. However, again increase in aerosol mass and EC concentrations possibly because of a high increase in road traffic in recent years. According to the economic survey of New Delhi 2008-09, the number of vehicles (which includes all types of engines, i.e., petrol, diesel and CNG) has grown from ~3.3 millions in 1997-98 to ~5.6 millions in 2007-08. The influence of engine types and vehicle population on aerosol loading can also be explained well by SO2 and

  11. Size-resolved aerosol chemical concentrations at rural and urban sites in Central California, USA

    NASA Astrophysics Data System (ADS)

    Chow, Judith C.; Watson, John G.; Lowenthal, Douglas H.; Magliano, Karen L.

    2008-11-01

    Aerosol size distributions were measured with Micro Orifice Uniform Deposit Impactor (MOUDI) cascade impactors at the rural Angiola and urban Fresno Supersites in California's San Joaquin Valley during the California Regional PM 10/PM 2.5 Air Quality Study (CRPAQS) winter campaign from December 15, 2000 to February 3, 2001. PM 2.5 filter samples were collected concurrently at both sites with Sequential Filter Samplers (SFS). MOUDI nitrate (NO 3-) concentrations reached 66 μg/m 3 on January 6, 2001 during the 1000-1600 PST (GMT-8) period. Pair-wise comparisons between PM 2.5 MOUDI and SFS concentrations revealed high correlations at the Angiola site ( r > 0.93) but more variability ( r < 0.85) at the Fresno site for NO 3-, sulfate (SO 4=), and ammonium (NH 4+). Correlations were higher at Fresno ( r > 0.87) than at Angiola ( r < 0.7) for organic carbon (OC), elemental carbon (EC), and total carbon (TC). NO 3- and SO 4= size distributions in Fresno were multi-modal and wider than the uni-modal distributions observed at Angiola. Geometric mean diameters (GMD) were smaller for OC and EC than for NO 3- and SO 4= at both sites. OC and EC were more concentrated on the lowest MOUDI stage (0.056 µm) at Angiola than at Fresno. The NO 3- GMD increased from 0.97 to 1.02 µm as the NO 3- concentration at Angiola increased from 43 to 66 µg m - 3 during a PM 2.5 episode from January 4-7, 2001. There was a direct relationship between GMD and NO 3- and SO 4= concentrations at Angiola but no such relationships for OC or EC. This demonstrates that secondary aerosol formation increases both concentration and particle size for the rural California environment.

  12. Patterns in atmospheric carbonaceous aerosols in China: emission estimates and observed concentrations

    NASA Astrophysics Data System (ADS)

    Cui, H.; Mao, P.; Zhao, Y.; Nielsen, C. P.; Zhang, J.

    2015-03-01

    China is experiencing severe carbonaceous aerosol pollution driven mainly by large emissions resulting from intensive use of solid fuels. To gain a better understanding of the levels and trends of carbonaceous aerosol emissions and the resulting ambient concentrations at the national scale, we update an emission inventory of anthropogenic organic carbon (OC) and elemental carbon (EC) and employ existing observational studies to analyze characteristics of these aerosols including temporal, spatial, and size distributions, and the levels and shares of secondary organic carbon (SOC) in total OC. We further use ground observations to test the levels and inter-annual trends of the calculated national and provincial emissions of carbonaceous aerosols, and propose possible improvements in emission estimation for the future. The national OC emissions are estimated to have increased 29% from 2000 (2127 Gg) to 2012 (2749 Gg) and EC by 37% (from 1356 to 1857 Gg). The residential, industrial, and transportation sectors contributed an estimated 76 ± 2, 19 ± 2 and 5 ± 1% of the total emissions of OC, respectively, and 52 ± 3, 32 ± 2 and 16 ± 2% of EC. Updated emission factors based on the most recent local field measurements, particularly for biofuel stoves, lead to considerably lower emissions of OC compared to previous inventories. Compiling observational data across the country, higher concentrations of OC and EC are found in northern and inland cities, while larger OC/EC and SOC/OC ratios are found in southern cities, due to the joint effects of primary emissions and meteorology. Higher SOC/OC ratios are estimated at rural and remote sites compared to urban ones, attributed to more emissions of OC from biofuel use, more biogenic emissions of volatile organic compound (VOC) precursors to SOC, and/or transport of aged aerosols. For most sites, higher concentrations of OC, EC, and SOC are observed in colder seasons, while SOC/OC is reduced, particularly at rural and

  13. Patterns in atmospheric carbonaceous aerosols in China: emission estimates and observed concentrations

    NASA Astrophysics Data System (ADS)

    Cui, H.; Mao, P.; Zhao, Y.; Nielsen, C. P.; Zhang, J.

    2015-08-01

    China is experiencing severe carbonaceous aerosol pollution driven mainly by large emissions resulting from intensive use of solid fuels. To gain a better understanding of the levels and trends of carbonaceous aerosol emissions and the resulting ambient concentrations at the national scale, we update an emission inventory of anthropogenic organic carbon (OC) and elemental carbon (EC) and employ existing observational studies to analyze characteristics of these aerosols including temporal, spatial, and size distributions, and the levels and shares of secondary organic carbon (SOC) in total OC. We further use ground observations to test the levels and inter-annual trends of the calculated national and provincial emissions of carbonaceous aerosols, and propose possible improvements in emission estimation for the future. The national OC emissions are estimated to have increased 29 % from 2000 (2127 Gg) to 2012 (2749 Gg) and EC by 37 % (from 1356 to 1857 Gg). The residential, industrial, and transportation sectors contributed an estimated 74-78, 17-21, and 4-6 % of the total emissions of OC, respectively, and 49-55, 30-34, and 14-18 % of EC. Updated emission factors (EFs) based on the most recent local field measurements, particularly for biofuel stoves, led to considerably lower emissions of OC compared to previous inventories. Compiling observational data across the country, higher concentrations of OC and EC are found in northern and inland cities, while higher OC / EC ratios are found in southern sites, due to the joint effects of primary emissions and meteorology. Higher OC / EC ratios are estimated at rural and remote sites compared to urban ones, attributed to more emissions of OC from biofuel use, more biogenic emissions of volatile organic compound (VOC) precursors to SOC, and/or transport of aged aerosols. For most sites, higher concentrations of OC, EC, and SOC are observed in colder seasons, while SOC / OC is reduced, particularly at rural and remote sites

  14. How comparable are size-resolved particle number concentrations from different instruments?

    NASA Astrophysics Data System (ADS)

    Hornsby, K. E.; Pryor, S. C.

    2012-12-01

    The need for comparability of particle size resolved measurements originates from multiple drivers including: (i) Recent suggestions that air quality standards for particulate matter should migrate from being mass-based to incorporating number concentrations. This move would necessarily be predicated on measurement comparability which is absolutely critical to compliance determination. (ii) The need to quantify and diagnose causes of variability in nucleation and growth rates in nano-particle experiments conducted in different locations. (iii) Epidemiological research designed to identify key parameters in human health responses to fine particle exposure. Here we present results from a detailed controlled laboratory instrument inter-comparison experiment designed to investigate data comparability in the size range of 2.01-523.3 nm across a range of particle composition, modal diameter and absolute concentration. Particle size distributions were generated using a TSI model 3940 Aerosol Generation System (AGS) diluted using zero air, and sampled using four TSI Scanning Mobility Particle Spectrometer (SMPS) configurations and a TSI model 3091 Fast Mobility Particle Sizer (FMPS). The SMPS configurations used two Electrostatic Classifiers (EC) (model 3080) attached to either a Long DMA (LDMA) (model 3081) or a Nano DMA (NDMA) (model 3085) plumbed to either a TSI model 3025A Butanol Condensed Particle Counting (CPC) or a TSI model 3788 Water CPC. All four systems were run using both high and low flow conditions, and were operated with both the internal diffusion loss and multiple charge corrections turned on. The particle compositions tested were sodium chloride, ammonium nitrate and olive oil diluted in ethanol. Particles of all three were generated at three peak concentration levels (spanning the range observed at our experimental site), and three modal particle diameters. Experimental conditions were maintained for a period of 20 minutes to ensure experimental

  15. Impact of atmospheric boundary layer depth variability and wind reversal on the diurnal variability of aerosol concentration at a valley site.

    PubMed

    Pal, S; Lee, T R; Phelps, S; De Wekker, S F J

    2014-10-15

    The development of the atmospheric boundary layer (ABL) plays a key role in affecting the variability of atmospheric constituents such as aerosols, greenhouse gases, water vapor, and ozone. In general, the concentration of any tracers within the ABL varies due to the changes in the mixing volume (i.e. ABL depth). In this study, we investigate the impact on the near-surface aerosol concentration in a valley site of 1) the boundary layer dilution due to vertical mixing and 2) changes in the wind patterns. We use a data set obtained during a 10-day field campaign in which a number of remote sensing and in-situ instruments were deployed, including a ground-based aerosol lidar system for monitoring of the ABL top height (zi), a particle counter to determine the number concentration of aerosol particles at eight different size ranges, and tower-based standard meteorological instruments. Results show a clearly visible decreasing trend of the mean daytime zi from 2900 m AGL (above ground level) to 2200 m AGL during a three-day period which resulted in increased near-surface pollutant concentrations. An inverse relationship exists between the zi and the fine fraction (0.3-0.7 μm) accumulation mode particles (AMP) on some days due to the dilution effect in a well-mixed ABL. These days are characterized by the absence of daytime upvalley winds and the presence of northwesterly synoptic-driven winds. In contrast, on the days with an onset of an upvalley wind circulation after the morning transition, the wind-driven local transport mechanism outweighs the ABL-dilution effect in determining the variability of AMP concentration. The interplay between the ABL depth evolution and the onset of the upvalley wind during the morning transition period significantly governs the air quality in a valley and could be an important component in the studies of mountain meteorology and air quality. PMID:25105753

  16. Control of aerosol contaminants in indoor air: combining the particle concentration reduction with microbial inactivation.

    PubMed

    Grinshpun, Sergey A; Adhikari, Atin; Honda, Takeshi; Kim, Ki Youn; Toivola, Mika; Rao, K S Ramchander; Reponen, Tiina

    2007-01-15

    An indoor air purification technique, which combines unipolar ion emission and photocatalytic oxidation (promoted by a specially designed RCI cell), was investigated in two test chambers, 2.75 m3 and 24.3 m3, using nonbiological and biological challenge aerosols. The reduction in particle concentration was measured size selectively in real-time, and the Air Cleaning Factor and the Clean Air Delivery Rate (CADR) were determined. While testing with virions and bacteria, bioaerosol samples were collected and analyzed, and the microorganism survival rate was determined as a function of exposure time. We observed that the aerosol concentration decreased approximately 10 to approximately 100 times more rapidly when the purifier operated as compared to the natural decay. The data suggest that the tested portable unit operating in approximately 25 m3 non-ventilated room is capable to provide CADR-values more than twice as great than the conventional closed-loop HVAC system with a rating 8 filter. The particle removal occurred due to unipolar ion emission, while the inactivation of viable airborne microorganisms was associated with photocatalytic oxidation. Approximately 90% of initially viable MS2 viruses were inactivated resulting from 10 to 60 min exposure to the photocatalytic oxidation. Approximately 75% of viable B. subtilis spores were inactivated in 10 min, and about 90% or greater after 30 min. The biological and chemical mechanisms that led to the inactivation of stress-resistant airborne viruses and bacterial spores were reviewed. PMID:17310729

  17. Aerosol and NOx emission factors and submicron particle number size distributions in two road tunnels with different traffic regimes

    NASA Astrophysics Data System (ADS)

    Imhof, D.; Weingartner, E.; Prévôt, A. S. H.; Ordóñez, C.; Kurtenbach, R.; Wiesen, P.; Rodler, J.; Sturm, P.; McCrae, I.; Ekström, M.; Baltensperger, U.

    2006-06-01

    Measurements of aerosol particle number size distributions (18-700 nm), mass concentrations (PM2.5 and PM10) and NOx were performed in the Plabutsch tunnel, Austria, and in the Kingsway tunnel, United Kingdom. These two tunnels show different characteristics regarding the roadway gradient, the composition of the vehicle fleet and the traffic frequency. The submicron particle size distributions contained a soot mode in the diameter range D=80-100 nm and a nucleation mode in the range of D=20-40 nm. In the Kingsway tunnel with a significantly lower particle number and volume concentration level than in the Plabutsch tunnel, a clear diurnal variation of nucleation and soot mode particles correlated to the traffic density was observed. In the Plabutsch tunnel, soot mode particles also revealed a diurnal variation, whereas no substantial variation was found for the nucleation mode particles. During the night a higher number concentration of nucleation mode particles were measured than soot mode particles and vice versa during the day. In this tunnel with very high soot emissions during daytime due to the heavy-duty vehicle (HDV) share of 18% and another 40% of diesel driven light-duty vehicles (LDV) semivolatile species condense on the pre-existing soot surface area rather than forming new particles by homogeneous nucleation. With the low concentration of soot mode particles in the Kingsway tunnel, also the nucleation mode particles exhibit a diurnal variation. From the measured parameters real-world traffic emission factors were estimated for the whole vehicle fleet as well as differentiated into the two categories LDV and HDV. In the particle size range D=18-700 nm, each vehicle of the mixed fleet emits (1.50±0.08)×1014 particles km-1 (Plabutsch) and (1.26±0.10)×1014 particles km-1 (Kingsway), while particle volume emission factors of 0.209±0.008 cm3 km-1 and 0.036±0.004 cm3 km-1, respectively, were obtained. PM1 emission factors of 104±4 mg km-1 (Plabutsch

  18. Aerosol and NOx emission factors and submicron particle number size distributions in two road tunnels with different traffic regimes

    NASA Astrophysics Data System (ADS)

    Imhof, D.; Weingartner, E.; Prévát, A. S. H.; Ordóñez, C.; Kurtenbach, R.; Wiesen, P.; Rodler, J.; Sturm, P.; McCrae, I.; Sjödin, Å.; Baltensperger, U.

    2005-07-01

    Measurements of aerosol particle number size distributions (18-700 nm), mass concentrations (PM2.5 and PM10) and NOx were performed in the Plabutsch tunnel, Austria, and in the Kingsway tunnel, United Kingdom. These two tunnels show different characteristics regarding the roadway gradient, the composition of the vehicle fleet and the traffic frequency. The submicron particle size distributions contained a soot mode in the diameter range D=80-100 nm and a nucleation mode in the range of D=20-40 nm. In the Kingsway tunnel with a significantly lower particle number and volume concentration level than in the Plabutsch tunnel, a clear diurnal variation of nucleation and soot mode particles correlated to the traffic density was observed. In the Plabutsch tunnel, soot mode particles also revealed a diurnal variation, whereas no substantial variation was found for the nucleation mode particles. During the night a higher number concentration of nucleation mode particles were measured than soot mode particles and vice versa during the day. In this tunnel with very high soot emissions during daytime due to the heavy-duty vehicle (HDV) share of 18% and another 40% of diesel driven light-duty vehicles (LDV) semivolatile species condense on the pre-existing soot surface area rather than forming new particles by homogeneous nucleation. With the low concentration of soot mode particles in the Kingsway tunnel, also the nucleation mode particles exhibit a diurnal variation. From the measured parameters real-world traffic emission factors were estimated for the whole vehicle fleet as well as differentiated into the two categories LDV and HDV. In the particle size range D=18-700 nm, each vehicle of the mixed fleet emits (1.50±0.08)·1014 particles km-1 (Plabutsch) and (1.26±0.10)·1014 particles km-1 (Kingsway), while particle volume emission factors of 0.209±0.008 cm3 km-1 and 0.036±0.004 cm3 km-1, respectively, were obtained. PM1 emission factors of 104±4 mg km-1 (Plabutsch

  19. Characterization and source apportionment of particle number concentration at a semi-urban tropical environment.

    PubMed

    Khan, Md Firoz; Latif, Mohd Talib; Amil, Norhaniza; Juneng, Liew; Mohamad, Noorlin; Nadzir, Mohd Shahrul Mohd; Hoque, Hossain Mohammed Syedul

    2015-09-01

    Principal component analysis (PCA) and correlation have been used to study the variability of particle mass and particle number concentrations (PNC) in a tropical semi-urban environment. PNC and mass concentration (diameter in the range of 0.25->32.0 μm) have been measured from 1 February to 26 February 2013 using an in situ Grimm aerosol sampler. We found that the 24-h average total suspended particulates (TSP), particulate matter ≤10 μm (PM10), particulate matter ≤2.5 μm (PM2.5) and particulate matter ≤1 μm (PM1) were 14.37 ± 4.43, 14.11 ± 4.39, 12.53 ± 4.13 and 10.53 ± 3.98 μg m(-3), respectively. PNC in the accumulation mode (<500 nm) was the most abundant (at about 99 %). Five principal components (PCs) resulted from the PCA analysis where PC1 (43.8 % variance) predominates with PNC in the fine and sub-microme tre range. PC2, PC3, PC4 and PC5 explain 16.5, 12.4, 6.0 and 5.6 % of the variance to address the coarse, coarser, accumulation and giant fraction of PNC, respectively. Our particle distribution results show good agreement with the moderate resolution imaging spectroradiometer (MODIS) distribution. PMID:25925145

  20. Worldwide impact of aerosol's time scale on the predicted long-term concentrating solar power potential.

    PubMed

    Ruiz-Arias, Jose A; Gueymard, Christian A; Santos-Alamillos, Francisco J; Pozo-Vázquez, David

    2016-01-01

    Concentrating solar technologies, which are fuelled by the direct normal component of solar irradiance (DNI), are among the most promising solar technologies. Currently, the state-of the-art methods for DNI evaluation use datasets of aerosol optical depth (AOD) with only coarse (typically monthly) temporal resolution. Using daily AOD data from both site-specific observations at ground stations as well as gridded model estimates, a methodology is developed to evaluate how the calculated long-term DNI resource is affected by using AOD data averaged over periods from 1 to 30 days. It is demonstrated here that the use of monthly representations of AOD leads to systematic underestimations of the predicted long-term DNI up to 10% in some areas with high solar resource, which may result in detrimental consequences for the bankability of concentrating solar power projects. Recommendations for the use of either daily or monthly AOD data are provided on a geographical basis. PMID:27507711

  1. Ozone and aerosol tropospheric concentrations variability analyzed using the ADRIMED measurements and the WRF and CHIMERE models

    NASA Astrophysics Data System (ADS)

    Menut, L.; Mailler, S.; Siour, G.; Bessagnet, B.; Turquety, S.; Rea, G.; Briant, R.; Mallet, M.; Sciare, J.; Formenti, P.; Meleux, F.

    2015-06-01

    During the months of June and July 2013, over the Euro-Mediterranean area, the ADRIMED (Aerosol Direct Radiative Impact on the regional climate in the MEDiterranean region) project was dedicated to characterize the ozone and aerosol concentrations in the troposphere. It is first shown that this period was not highly polluted compared to previous summers in this region, with a moderate ozone production, no significant vegetation fire events and several precipitation periods scavenging the aerosol. The period is modeled with the WRF (Weather Research and Forecasting) and CHIMERE models, and their ability to quantify the observed pollution transport events is presented. The CHIMERE model simulating all kinds of sources (anthropogenic, biogenic, mineral dust, vegetation fires); the aerosol speciation, not available with the measurements, is presented: during the whole period, the aerosol was mainly constituted by mineral dust, sea salt and sulfates close to the surface and mainly by mineral dust in the troposphere. Compared to the AERONET (Aerosol Robotic Network) size distribution, it is shown that the model underestimates the coarse mode near mineral dust sources and overestimates the fine mode in the Mediterranean area, highlighting the need to improve the model representation of the aerosol size distribution both during emissions, long-range transport and deposition.

  2. Prediction Of Organic Aerosol Volatility And Unidentified Functional Group Concentrations From Fourier Transform Infrared (FTIR) Spectroscopy Measurements

    NASA Astrophysics Data System (ADS)

    Ruggeri, G.; Shipley, S.; Henderson, B. H.; Takahama, S.

    2014-12-01

    Fourier Transform Infrared (FTIR) spectroscopy is used to measure the functional group composition of organic aerosols (Russell et al., 2011). However, certain functional groups are not directly detected by FTIR spectroscopy, either due to fundamental limitations of the technique (e.g. tertiary carbons), or specific limitations of commonly employed methods of sample collection and analysis (e.g. ester and ether groups, Takahama et al., 2013). In addition, FTIR does not probe the size of molecules comprising an organic aerosol mixture, which prevents the direct calculation of organic aerosol volatility from FTIR measurements. In this study, primary organic aerosol concentrations in mixtures corresponding to different ambient scenarios have been extracted from previous GC-MS studies (Rogge et al., 1993). Secondary organic aerosol concentrations for different scenarios are simulated with an explicit chemistry model (Master Chemical Mechanism, http://mcm.leeds.ac.uk/MCM ; Jerkin et al. 1997; Saunders et al., 2003; Jerkin et al., 2003) and partitioning model (SIMPOL.1, Pankow et al., 2008). For each of the different scenarios the concentrations of functional groups that are typically accessible by FTIR are calculated and analyzed in relation to the extra information not easily accessible by FTIR (e.g. volatility, tertiary carbons, ester and ether). The ability to predict the unknown quantities from FTIR measurements and thereby reduce the uncertainty in OM concentrations and OM/OC ratios measured by FTIR is examined and discussed.

  3. Ambient aerosol chlorine concentrations and artefacts during the MEGAPOLI Paris campaigns

    NASA Astrophysics Data System (ADS)

    Furger, Markus; Visser, Suzanne; Slowik, Jay; Crippa, Monica; Poulain, Laurent; Sciare, Jean; Flechsig, Uwe; Prévôt, André; Baltensperger, Urs

    2015-04-01

    Trace elements, especially those that are toxic, can affect the environment in significant ways. Studying them is advantageous with respect to a refinement of source apportionment when measured with high time resolution and appropriate size segregation. This approach is especially useful in urban environments with numerous time-variant emission sources distributed across a relatively narrow space. Two field campaigns took place in the framework of the MEGAPOLI project in Paris, France: one in the summer of 2009 (1-31 July), the other in the winter of 2010 (11 Jan - 10 Feb). Rotating drum impactors (RDI) were operated at an urban and a suburban site in each campaign. The RDI segregated the aerosols into three size ranges (PM10-2.5, PM2.5-1.0 and PM1.0-0.3) and sampled with 2-hour time resolution. The samples were analyzed with synchrotron radiation-induced X-ray fluorescence spectrometry (SR-XRF) at the synchrotron facility of the Paul Scherrer Institute (SLS), where a broad range of elements (Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn) was analyzed for each size range. Time series of the analyzed elements for the different sites and campaigns were prepared to characterize the aerosol trace element composition and temporal behavior for different weather situations and urban environments. Quality assurance was performed partly by intercomparison with independent measurements. An exceptional behavior was observed for chlorine (Cl), where periods with zero RDI concentration alternated with periods of normal load. Zero concentrations were not observed in particle-into-liquid (PILS) measurements. This identifies the observed behavior as a RDI sampling artefact. Nevertheless, the non-zero periods of Cl concentrations are still a gain in information compared to conventional sampling techniques, mainly due to the high time resolution.

  4. Effects of precursor concentration and acidic sulfate in aqueous glyoxal-OH radical oxidation and implications for secondary organic aerosol.

    PubMed

    Tan, Yi; Perri, Mark J; Seitzinger, Sybil P; Turpin, Barbara J

    2009-11-01

    Previous experiments demonstrated that aqueous OH radical oxidation of glyoxal yields low-volatility compounds. When this chemistry takes place in clouds and fogs, followed by droplet evaporation (or if it occurs in aerosol water), the products are expected to remain partially in the particle phase, forming secondary organic aerosol (SOA). Acidic sulfate exists ubiquitously in atmospheric water and has been shown to enhance SOA formation through aerosol phase reactions. In this work, we investigate how starting concentrations of glyoxal (30-3000 microM) and the presence of acidic sulfate (0-840 microM) affect product formation in the aqueous reaction between glyoxal and OH radical. The oxalic acid yield decreased with increasing precursor concentrations, and the presence of sulfuric acid did not alter oxalic acid concentrations significantly. A dilute aqueous chemistry model successfully reproduced oxalic acid concentrations, when the experiment was performed at cloud-relevant concentrations (glyoxal <300 microM), but predictions deviated from measurements at increasing concentrations. Results elucidate similarities and differences in aqueous glyoxal chemistry in clouds and in wet aerosols. They validate for the first time the accuracy of model predictions at cloud-relevant concentrations. These results suggest that cloud processing of glyoxal could be an important source of SOA. PMID:19924930

  5. An Investigation of Size-Dependent Concentration of Trace Elements in Aerosols Emitted from the Oil-Fired Heating Plants

    NASA Technical Reports Server (NTRS)

    Singh, J. J.; Sentell, R. J.; Khandelwal, G. S.

    1976-01-01

    Aerosols emitted from two oil-fired heating plants were aerodynamically separated into eight size groups and were analyzed using the photon-induced X-ray emission (PIXE) technique. It was found that Zn, Mo, Ag, and Pb, and (to a lesser extent) Cd, have a tendency to concentrate preferentially on the smaller aerosols. All of these elements, in certain chemical forms, are known to be toxic. Zinc and molybdenum, although present in low concentrations in the parent fuels, show the strongest tendencies to be concentrated in finer aerosols. Selenium, previously reported to show a very strong tendency to concentration in finer fly ash from coal-fired power plants shows little preference for surface residence. Vanadium, which occurs in significant concentration in the oil fuels for both plants, also shows little preference for surface concentration. Even though the absolute concentrations of the toxic elements involved are well below the safety levels established by the National Institute for Occupational Safety and Health (NIOSH), it would be advisable to raise the heights of the heating-plant exhaust chimneys well above the neighborhood buildings to insure more efficient aerosol dispersal.

  6. Airborne DOAS measurements in Arctic: vertical distributions of aerosol extinction coefficient and NO2 concentration

    NASA Astrophysics Data System (ADS)

    Merlaud, A.; van Roozendael, M.; Theys, N.; Fayt, C.; Hermans, C.; Quennehen, B.; Schwarzenboeck, A.; Ancellet, G.; Pommier, M.; Pelon, J.; Burkhart, J.; Stohl, A.; de Mazière, M.

    2011-09-01

    We report on airborne Differential Optical Absorption Spectroscopy (DOAS) measurements of aerosol extinction and NO2 tropospheric profiles performed off the North coast of Norway in April 2008. The DOAS instrument was installed on the Safire ATR-42 aircraft during the POLARCAT-France spring campaign and recorded scattered light spectra in near-limb geometry using a scanning telescope. We use O4 slant column measurements to derive the aerosol extinction at 360 nm. Regularization is based on the maximum a posteriori solution, for which we compare a linear and a logarithmic approach. The latter inherently constrains the solution to positive values and yields aerosol extinction profiles more consistent with independently measured size distributions. We present results from two soundings performed on 8 April 2008 above 71° N, 22° E and on 9 April 2008 above 70° N, 17.8° E. The first profile shows aerosol extinction and NO2 in the marine boundary layer with respective values of 0.04 ± 0.005 km-1 and 1.9 ± 0.3 × 109 molec cm-3. A second extinction layer of 0.01 ± 0.003 km-1 is found at 4 km altitude where the NO2 concentration is 0.32 ± 0.2 × 109 molec cm-3. During the second sounding, clouds prevent retrieval of profile parts under 3 km altitude but a layer with enhanced extinction (0.025 ± 0.005 km-1) and NO2 (1.95 ± 0.2 × 109 molec cm-3) is clearly detected at 4 km altitude. From CO and ozone in-situ measurements complemented by back-trajectories, we interpret the measurements in the free troposphere as, for the first sounding, a mix between stratospheric and polluted air from Northern Europe and for the second sounding, polluted air from Central Europe containing NO2. Considering the boundary layer measurements of the first flight, modeled source regions indicate closer sources, especially the Kola Peninsula smelters, which can explain the NO2 enhancement not correlated with a CO increase at the same altitude.

  7. Impacts of alternative fuels in aviation on microphysical aerosol properties and predicted ice nuclei concentration at aircraft cruise altitude

    NASA Astrophysics Data System (ADS)

    Weinzierl, B.; D'Ascoli, E.; Sauer, D. N.; Kim, J.; Scheibe, M.; Schlager, H.; Moore, R.; Anderson, B. E.; Ullrich, R.; Mohler, O.; Hoose, C.

    2015-12-01

    In the past decades air traffic has been substantially growing affecting air quality and climate. According to the International Civil Aviation Authority (ICAO), in the next few years world passenger and freight traffic is expected to increase annually by 6-7% and 4-5%, respectively. One possibility to reduce aviation impacts on the atmosphere and climate might be the replacement of fossil fuels by alternative fuels. However, so far the effects of alternative fuels on particle emissions from aircraft engines and their ability to form contrails remain uncertain. To study the effects of alternative fuels on particle emissions and the formation of contrails, the Alternative Fuel Effects on Contrails and Cruise Emissions (ACCESS) field experiment was conducted in California. In May 2014, the DLR Falcon 20 and the NASA HU-25 jet aircraft were instrumented with an extended aerosol and trace gas payload probing different types of fuels including JP-8 and JP-8 blended with HEFA (Hydroprocessed Esters and Fatty Acids) while the NASA DC8 aircraft acted as the source aircraft for ACCESS-2. Emission measurements were taken in the DC8 exhaust plumes at aircraft cruise level between 9-12 km altitude and at distances between 50 m and 20 km behind the DC8 engines. Here, we will present results from the ACCESS-2 aerosol measurements which show a 30-60% reduction of the non-volatile (mainly black carbon) particle number concentration in the aircraft exhaust for the HEFA-blend compared to conventional JP-8 fuel. Size-resolved particle emission indices show the largest reductions for larger particle sizes suggesting that the HEFA blend contains fewer and smaller black carbon particles. We will combine the airborne measurements with a parameterization of deposition nucleation developed during a number of ice nucleation experiments at the AIDA chamber in Karlsruhe and discuss the impact of alternative fuels on the abundance of potential ice nuclei at cruise conditions.

  8. Dry deposition and concentration of marine aerosols in a coastal area, SW Sweden

    NASA Astrophysics Data System (ADS)

    Gustafsson, Mats E. R.; Franzén, Lars G.

    The present paper introduces a model for the dry deposition of marine aerosols in a coastal area of SW Sweden. The model, incorporating wind speed and distance from shore, is based on repeated measurements of salt impingement on specially designed salt traps in dense profiles from the shore and inland. The measurements show that the deposited salts include two significantly different components, one dynamic containing large droplets, with short residence time in the air, deposited close to the shore, the other one being microscopic droplets, with long residence time in the air and with a low deposition velocity (principally, the system is similar to that of mineral particles, i.e. saltating dune sand vs loess). The deposition of marine aerosols has various effects on the terrestrial environments. Aside from those associated to human activities, i.e. technical effects on outdoor electrical installations, increased corrosion of cars, etc. there are others associated to natural ecosystems. Hence, salts are important contributors to major and trace elements for plant growth. On the other hand, the deposition of windborne salt spray is believed to form an important stress factor on forests and especially to exposed stands of Norway spruce ( Picea abies L.). In this latter sense it is the authors' opinion that the rising number of westerly gales reported on the Swedish west coast during the last two decades might give an important contribution to the increasing amounts of damage observed from coniferous forests in SW Sweden.

  9. Thoron concentration, aerosol characteristics of 212Pb and estimation of equivalent dose

    NASA Astrophysics Data System (ADS)

    Mohery, M.; Abdallah, A. M.; Kelany, Adel M.; Yaghmour, S. J.

    2014-08-01

    The thoron gas (220Rn) activity concentration as well as activity size distribution of unattached and attached 212Pb to aerosol particles was measured in the open air of Jeddah City, Kingdom of Saudi Arabia. An electroprecipitation method was applied for measuring the 220Rn concentration. A mean activity concentration of 220Rn was determined to be 1.80±0.47 Bq m-3. The unattached activities of 212Pb were collected using the wire screen diffusion battery technique while a low-pressure cascade impactor collected the attached activities. The mean activity median thermodynamic diameter (AMTD) of unattached 212Pb was determined to be 1.32 nm with a relative mean geometric standard deviation (σg) of 1.45. A mean concentration of unattached activity of 212Pb was found to be 9.48±1.12 mBq m-3. A mean unattached fraction (fp) of 0.028±0.002 was obtained at a mean aerosol particle concentration of 29×103 cm-3. Sometimes, the fp values were less than the detection limit of 0.009. A mean activity median aerodynamic diameter (AMAD) of the accumulation mode of attached 212Pb was determined to be 352 nm with a mean (σg) of 2.6. The mean value of specific air activity concentration of 212Pb associated with that mode was determined to be 310±12 mBq m-3. With a dosimetric model calculation (ICRP, 1994) the total and regional deposition fractions, total and regional equivalent doses could be evaluated considering the obtained parameters of the activity size distributions. At a total deposition fraction of about 97% of unattached activities the total equivalent dose to the human lung was determined to be 0.16 μSv while a total equivalent dose of 0.44 μSv was determined at a total deposition fraction of about 23% for the attached activities. It was found that an unattached fraction of fP≈3% yields to about 27% of the total equivalent dose.

  10. A Miniature System for Separating Aerosol Particles and Measuring Mass Concentrations

    PubMed Central

    Liang, Dao; Shih, Wen-Pin; Chen, Chuin-Shan; Dai, Chi-An

    2010-01-01

    We designed and fabricated a new sensing system which consists of two virtual impactors and two quartz-crystal microbalance (QCM) sensors for measuring particle mass concentration and size distribution. The virtual impactors utilized different inertial forces of particles in air flow to classify different particle sizes. They were designed to classify particle diameter, d, into three different ranges: d < 2.28 μm, 2.28 μm ≤ d ≤ 3.20 μm, d > 3.20 μm. The QCM sensors were coated with a hydrogel, which was found to be a reliable adhesive for capturing aerosol particles. The QCM sensor coated with hydrogel was used to measure the mass loading of particles by utilizing its characteristic of resonant frequency shift. An integrated system has been demonstrated. PMID:22319317

  11. Characterizing the influence of anthropogenic emissions and transport variability on sulfate aerosol concentrations at Mauna Loa Observatory

    NASA Astrophysics Data System (ADS)

    Potter, Lauren E.

    Sulfate aerosol in the atmosphere has substantial impacts on human health and environmental quality. Most notably, atmospheric sulfate has the potential to modify the earth's climate system through both direct and indirect radiative forcing mechanisms (Meehl et al., 2007). Emissions of sulfur dioxide, the primary precursor of sulfate aerosol, are now globally dominated by anthropogenic sources as a result of widespread fossil fuel combustion. Economic development in Asian countries since 1990 has contributed considerably to atmospheric sulfur loading, particularly China, which currently emits approximately 1/3 of global anthropogenic SO2 (Klimont et al., 2013). Observational and modeling studies have confirmed that anthropogenic pollutants from Asian sources can be transported long distances with important implications for future air quality and global climate change. Located in the remote Pacific Ocean (19.54°N, 155.58°W) at an elevation of 3.4 kilometers above sea level, Mauna Loa Observatory (MLO) is an ideal measurement site for ground-based, free tropospheric observations and is well situated to experience influence from springtime Asian outflow. This study makes use of a 14-year data set of aerosol ionic composition, obtained at MLO by the University of Hawaii at Manoa. Daily filter samples of total aerosol concentrations were made during nighttime downslope (free-tropospheric) transport conditions, from 1995 to 2008, and were analyzed for aerosol-phase concentrations of the following species: nitrate (NO3-), sulfate (SO42-), methanesulfonate (MSA), chloride (Cl-), oxalate, sodium (Na+), ammonium (NH 4+), potassium (K+), magnesium (Mg 2+), and calcium (Ca2+). An understanding of the factors controlling seasonal and interannual variations in aerosol speciation and concentrations at this site is complicated by the relatively short lifetimes of aerosols, compared with greenhouse gases which have also been sampled over long time periods at MLO. Aerosol filter

  12. [Concentration distribution of metal elements in atmospheric aerosol under different weather conditions in Qingdao Coastal Region].

    PubMed

    Chen, Xiao-Jing; Qi, Jian-Hua; Liu, Ning; Zhang, Xiang-Yu; Shen, Heng-Qing; Liu, Ming-Xu

    2014-10-01

    To know the influence of different weather conditions on the concentration of metal elements in aerosols in the coastal region, total suspended particles (TSP) samples were collected from April to May 2012, and August 2012 to March 2013 in the Qingdao coastal region, and common trace metals were analyzed by using Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) and Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES). The results showed that Al, Ca, Fe, Na, K and Mg were the dominant metal elements in TSP, and the sum of the six elements accounted for 94.2% of the sum of all metals. TSP and metal elements had significant monthly variations, Fe, Al, K, Ca, Mg, Zn, Ba, Mn, Ti, Sr and Li had the highest concentration in November and January, while Be, Sc, Co, Ni and Cr showed the highest value in January. Na had the highest concentration in August, November and February, and the lowest in December. Pb had the highest concentration in January and February, and the lowest in August and December. Enrichment factors indicated that Be, Co, Al, Ca, Fe, K, Mg, Mn, Sr and Ti were mainly affected by natural sources; Li, Cr, Ni, Zn, Ba and Na were affected by natural sources and part of anthropogenic sources; Pb was mainly from anthropogenic sources. Different weather conditions had great impact on TSP and metal elements concentrations, all the measured metals had the highest concentrations in smog except Ti. Compared with the sunny day, the concentration of atmospheric particulate Ti decreased, while the other elements increased by 1 to 4 times in smog. Li, Be, Cr, Ni, Al, Fe, Mg and Mn had little variation in concentration in foggy day, and the concentration of Pb and Na increased considerably. The concentration of Co, Ca and Ti reduced obviously in fog. Except for Cr, Co and Ti, the other elements increased by 1 to 3 times in haze. Most of the elements had the minimal enrichment factors in sunny day, while the other had the maximal enrichment factor in

  13. Global Estimates of Average Ground-Level Fine Particulate Matter Concentrations from Satellite-Based Aerosol Optical Depth

    NASA Technical Reports Server (NTRS)

    Van Donkelaar, A.; Martin, R. V.; Brauer, M.; Kahn, R.; Levy, R.; Verduzco, C.; Villeneuve, P.

    2010-01-01

    Exposure to airborne particles can cause acute or chronic respiratory disease and can exacerbate heart disease, some cancers, and other conditions in susceptible populations. Ground stations that monitor fine particulate matter in the air (smaller than 2.5 microns, called PM2.5) are positioned primarily to observe severe pollution events in areas of high population density; coverage is very limited, even in developed countries, and is not well designed to capture long-term, lower-level exposure that is increasingly linked to chronic health effects. In many parts of the developing world, air quality observation is absent entirely. Instruments aboard NASA Earth Observing System satellites, such as the MODerate resolution Imaging Spectroradiometer (MODIS) and the Multi-angle Imaging SpectroRadiometer (MISR), monitor aerosols from space, providing once daily and about once-weekly coverage, respectively. However, these data are only rarely used for health applications, in part because the can retrieve the amount of aerosols only summed over the entire atmospheric column, rather than focusing just on the near-surface component, in the airspace humans actually breathe. In addition, air quality monitoring often includes detailed analysis of particle chemical composition, impossible from space. In this paper, near-surface aerosol concentrations are derived globally from the total-column aerosol amounts retrieved by MODIS and MISR. Here a computer aerosol simulation is used to determine how much of the satellite-retrieved total column aerosol amount is near the surface. The five-year average (2001-2006) global near-surface aerosol concentration shows that World Health Organization Air Quality standards are exceeded over parts of central and eastern Asia for nearly half the year.

  14. Effect of concentration and addition of ions on the adsorption of aerosol-OT to sapphire.

    PubMed

    Hellsing, Maja S; Rennie, Adrian R; Hughes, Arwel V

    2010-09-21

    Aerosol-OT (sodium bis 2-ethylhexyl sulfosuccinate or NaAOT) adsorbs to hydrophilic sapphire solid surfaces. The structure of the formed bilayer has been determined over the concentration range 0.2-7.4 mM NaAOT. It was found that the hydrocarbon tails pack at maximum packing limit at very low concentrations, and that the thickness of the bilayer was concentration-independent. The adsorption was found to increase with concentration, with the surfactant molecules packing closer laterally. The area per molecule was found to change from 138 ± 25 to 51 ± 4 A(2) over the concentration range studied, with the thickness of the layer being constant at 33 ± 2 A. Addition of small amounts of salt was found to increase the surface excess, with the bilayer being thinner with a slightly larger area per molecule. Addition of different salts of the same valency was found to have a very similar effect, as had the addition of NaOH and HCl. Hence, the effects of adding acid or base should be considered an effect of ionic strength rather than an effect of pH. Adsorption of NaAOT to the sapphire surface that carries an opposite charge to the anionic surfactant is similar in many respects to the adsorption reported previously for hydrophilic and hydrophobic silica surfaces. This suggests that the adsorption of NaAOT to a surface is driven primarily by NaAOT self-assembly rather than effects of electrostatic attraction to the interface. PMID:20735040

  15. Calibrating MODIS aerosol optical depth for predicting daily PM2.5 concentrations via statistical downscaling

    PubMed Central

    Chang, Howard H.; Hu, Xuefei; Liu, Yang

    2014-01-01

    There has been a growing interest in the use of satellite-retrieved aerosol optical depth (AOD) to estimate ambient concentrations of PM2.5 (particulate matter <2.5 μm in aerodynamic diameter). With their broad spatial coverage, satellite data can increase the spatial–temporal availability of air quality data beyond ground monitoring measurements and potentially improve exposure assessment for population-based health studies. This paper describes a statistical downscaling approach that brings together (1) recent advances in PM2.5 land use regression models utilizing AOD and (2) statistical data fusion techniques for combining air quality data sets that have different spatial resolutions. Statistical downscaling assumes the associations between AOD and PM2.5 concentrations to be spatially and temporally dependent and offers two key advantages. First, it enables us to use gridded AOD data to predict PM2.5 concentrations at spatial point locations. Second, the unified hierarchical framework provides straightforward uncertainty quantification in the predicted PM2.5 concentrations. The proposed methodology is applied to a data set of daily AOD values in southeastern United States during the period 2003–2005. Via cross-validation experiments, our model had an out-of-sample prediction R2 of 0.78 and a root mean-squared error (RMSE) of 3.61 μg/m3 between observed and predicted daily PM2.5 concentrations. This corresponds to a 10% decrease in RMSE compared with the same land use regression model without AOD as a predictor. Prediction performances of spatial–temporal interpolations to locations and on days without monitoring PM2.5 measurements were also examined. PMID:24368510

  16. Calibrating MODIS aerosol optical depth for predicting daily PM2.5 concentrations via statistical downscaling.

    PubMed

    Chang, Howard H; Hu, Xuefei; Liu, Yang

    2014-07-01

    There has been a growing interest in the use of satellite-retrieved aerosol optical depth (AOD) to estimate ambient concentrations of PM2.5 (particulate matter <2.5 μm in aerodynamic diameter). With their broad spatial coverage, satellite data can increase the spatial-temporal availability of air quality data beyond ground monitoring measurements and potentially improve exposure assessment for population-based health studies. This paper describes a statistical downscaling approach that brings together (1) recent advances in PM2.5 land use regression models utilizing AOD and (2) statistical data fusion techniques for combining air quality data sets that have different spatial resolutions. Statistical downscaling assumes the associations between AOD and PM2.5 concentrations to be spatially and temporally dependent and offers two key advantages. First, it enables us to use gridded AOD data to predict PM2.5 concentrations at spatial point locations. Second, the unified hierarchical framework provides straightforward uncertainty quantification in the predicted PM2.5 concentrations. The proposed methodology is applied to a data set of daily AOD values in southeastern United States during the period 2003-2005. Via cross-validation experiments, our model had an out-of-sample prediction R(2) of 0.78 and a root mean-squared error (RMSE) of 3.61 μg/m(3) between observed and predicted daily PM2.5 concentrations. This corresponds to a 10% decrease in RMSE compared with the same land use regression model without AOD as a predictor. Prediction performances of spatial-temporal interpolations to locations and on days without monitoring PM2.5 measurements were also examined. PMID:24368510

  17. Dependence of Heterogeneous OH Kinetics with Biomass Burning Aerosol Proxies on Oxidant Concentration and Relative Humidity

    NASA Astrophysics Data System (ADS)

    Slade, J. H.; Knopf, D. A.

    2013-12-01

    Chemical transformations of aerosol particles by heterogeneous reactions with trace gases such as OH radicals can influence particle physicochemical properties and lifetime, affect cloud formation, light scattering, and human health. Furthermore, OH oxidation can result in degradation of particle mass by volatilization reactions, altering the budget of volatile organic compounds (VOCs). However, the reactive uptake coefficient (γ) and particle oxidation degree can vary depending on several factors including oxidant concentration and relative humidity (RH). While RH can influence the extent of dissociation/ionization, it can also affect particle phase and thus oxidant diffusivity. Only one study so far has investigated the effect of RH on the rate of OH uptake to organic surfaces; however, the underlying processes affecting OH reactivity with organic aerosol under humidified conditions still remains elusive. Here, we determine the effect of RH on OH reactivity with laboratory-generated biomass burning aerosol (BBA) surrogate particles: levoglucosan and 4-methyl-5-nitrocatechol. The effect of OH concentration on γ for three common BBA molecular markers (levoglucosan, abietic acid, and nitroguaiacol) under dry conditions was investigated from [OH]≈107-1011 molecule cm-3, covering both [OH] in biomass burning plumes and [OH] commonly used in particle aging studies. Furthermore, key VOC reaction products and their production pathways resulting from BBA volatilization by OH were identified. OH radicals are produced using a microwave induced plasma (MIP) of H2 in He or Ar followed by reaction with O2, or by photolysis of O3 in the presence of H2O. A cylindrical rotating wall flow-tube reactor and fast-flow aerosol flow reactor are used for conducting kinetic studies. OH is detected using a Chemical Ionization Mass Spectrometer (CIMS) and a Proton Transfer Reaction Time-of-Flight Mass Spectrometer (PTR-ToF-MS) is employed for VOC analysis. γ decreases from 0.2-0.5 at

  18. Technical note: An improved approach to determining background aerosol concentrations with PILS sampling on aircraft

    NASA Astrophysics Data System (ADS)

    Fukami, Christine S.; Sullivan, Amy P.; Ryan Fulgham, S.; Murschell, Trey; Borch, Thomas; Smith, James N.; Farmer, Delphine K.

    2016-07-01

    Particle-into-Liquid Samplers (PILS) have become a standard aerosol collection technique, and are widely used in both ground and aircraft measurements in conjunction with off-line ion chromatography (IC) measurements. Accurate and precise background samples are essential to account for gas-phase components not efficiently removed and any interference in the instrument lines, collection vials or off-line analysis procedures. For aircraft sampling with PILS, backgrounds are typically taken with in-line filters to remove particles prior to sample collection once or twice per flight with more numerous backgrounds taken on the ground. Here, we use data collected during the Front Range Air Pollution and Photochemistry Éxperiment (FRAPPÉ) to demonstrate that not only are multiple background filter samples are essential to attain a representative background, but that the chemical background signals do not follow the Gaussian statistics typically assumed. Instead, the background signals for all chemical components analyzed from 137 background samples (taken from ∼78 total sampling hours over 18 flights) follow a log-normal distribution, meaning that the typical approaches of averaging background samples and/or assuming a Gaussian distribution cause an over-estimation of background samples - and thus an underestimation of sample concentrations. Our approach of deriving backgrounds from the peak of the log-normal distribution results in detection limits of 0.25, 0.32, 3.9, 0.17, 0.75 and 0.57 μg m-3 for sub-micron aerosol nitrate (NO3-), nitrite (NO2-), ammonium (NH4+), sulfate (SO42-), potassium (K+) and calcium (Ca2+), respectively. The difference in backgrounds calculated from assuming a Gaussian distribution versus a log-normal distribution were most extreme for NH4+, resulting in a background that was 1.58× that determined from fitting a log-normal distribution.

  19. THE TAPERED ELEMENT OSCILLATING MICROBALANCE: A MONITOR FOR SHORT-TERM MEASUREMENT OF FINE AEROSOL MASS CONCENTRATION

    EPA Science Inventory

    A new instrument for short-term monitoring of ambient aerosol fine mass concentration has been developed based on a unique device called a Tapered Element Oscillating Microbalance (TEOM). The detector consists of a tapered hollow tube fixed at the wide end and holding an exchange...

  20. Regional and global impacts of Criegee intermediates on atmospheric sulphuric acid concentrations and first steps of aerosol formation.

    PubMed

    Percival, Carl J; Welz, Oliver; Eskola, Arkke J; Savee, John D; Osborn, David L; Topping, David O; Lowe, Douglas; Utembe, Steven R; Bacak, Asan; McFiggans, Gordon; Cooke, Michael C; Xiao, Ping; Archibald, Alexander T; Jenkin, Michael E; Derwent, Richard G; Riipinen, Ilona; Mok, Daniel W K; Lee, Edmond P F; Dyke, John M; Taatjes, Craig A; Shallcross, Dudley E

    2013-01-01

    Carbonyl oxides ("Criegee intermediates"), formed in the ozonolysis of alkenes, are key species in tropospheric oxidation of organic molecules and their decomposition provides a non-photolytic source of OH in the atmosphere (Johnson and Marston, Chem. Soc. Rev., 2008, 37, 699, Harrison et al, Sci, Total Environ., 2006, 360, 5, Gäb et al., Nature, 1985, 316, 535, ref. 1-3). Recently it was shown that small Criegee intermediates, C.I.'s, react far more rapidly with SO2 than typically represented in tropospheric models, (Welz, Science, 2012, 335, 204, ref. 4) which suggested that carbonyl oxides could have a substantial influence on the atmospheric oxidation of SO2. Oxidation of 502 is the main atmospheric source of sulphuric acid (H2SO4), which is a critical contributor to aerosol formation, although questions remain about the fundamental nucleation mechanism (Sipilä et al., Science, 2010, 327, 1243, Metzger et al., Proc. Natl. Acad. Sci. U. S. A., 2010 107, 6646, Kirkby et al., Nature, 2011, 476, 429, ref. 5-7). Non-absorbing atmospheric aerosols, by scattering incoming solar radiation and acting as cloud condensation nuclei, have a cooling effect on climate (Intergovernmental Panel on Climate Change (IPCC), Climate Change 2007: The Physical Science Basis, Cambridge University Press, 2007, ref. 8). Here we explore the effect of the Criegees on atmospheric chemistry, and demonstrate that ozonolysis of alkenes via the reaction of Criegee intermediates potentially has a large impact on atmospheric sulphuric acid concentrations and consequently the first steps in aerosol production. Reactions of Criegee intermediates with SO2 will compete with and in places dominate over the reaction of OH with SO2 (the only other known gas-phase source of H2SO4) in many areas of the Earth's surface. In the case that the products of Criegee intermediate reactions predominantly result in H2SO4 formation, modelled particle nucleation rates can be substantially increased by the improved

  1. Balloon measurements of aerosol in the Antarctic stratosphere

    NASA Technical Reports Server (NTRS)

    Morita, Y.; Takagi, M.; Iwasaka, Y.; Ono, A.

    1985-01-01

    Three balloon soundings of aerosol were conducted from Syowa Station, Antarctica in April, June and October 1983. Number concentration and the size distribution of aerosol particles with diameter greater than 0.3 microns were measured by using a light scattering aerosol particle counter. The influence of the eruption of Mt. El Chichon on the aerosol concentration in the stratosphere was observed on October 16. Very high aerosol concentration at stratospheric heights was obtained from the first successful aerosol sounding in winter Antarctic stratosphere. The result gives direct evidence of winter enhancement in the Antarctic stratosphere.

  2. Study of satellite retrieved aerosol optical depth spatial resolution effect on particulate matter concentration prediction

    NASA Astrophysics Data System (ADS)

    Strandgren, J.; Mei, L.; Vountas, M.; Burrows, J. P.; Lyapustin, A.; Wang, Y.

    2014-10-01

    The Aerosol Optical Depth (AOD) spatial resolution effect is investigated for the linear correlation between satellite retrieved AOD and ground level particulate matter concentrations (PM2.5). The Multi-Angle Implementation of Atmospheric Correction (MAIAC) algorithm was developed for the Moderate Resolution Imaging Spectroradiometer (MODIS) for obtaining AOD with a high spatial resolution of 1 km and provides a good dataset for the study of the AOD spatial resolution effect on the particulate matter concentration prediction. 946 Environmental Protection Agency (EPA) ground monitoring stations across the contiguous US have been used to investigate the linear correlation between AOD and PM2.5 using AOD at different spatial resolutions (1, 3 and 10 km) and for different spatial scales (urban scale, meso-scale and continental scale). The main conclusions are: (1) for both urban, meso- and continental scale the correlation between PM2.5 and AOD increased significantly with increasing spatial resolution of the AOD, (2) the correlation between AOD and PM2.5 decreased significantly as the scale of study region increased for the eastern part of the US while vice versa for the western part of the US, (3) the correlation between PM2.5 and AOD is much more stable and better over the eastern part of the US compared to western part due to the surface characteristics and atmospheric conditions like the fine mode fraction.

  3. The potential of LIRIC to validate the vertical profiles of the aerosol mass concentration estimated by an air quality model

    NASA Astrophysics Data System (ADS)

    Siomos, Nikolaos; Filoglou, Maria; Poupkou, Anastasia; Liora, Natalia; Dimopoulos, Spyros; Melas, Dimitris; Chaikovsky, Anatoli; Balis, Dimitris

    2015-04-01

    Vertical profiles of the aerosol mass concentration derived by a retrieval algorithm that uses combined sunphotometer and LIDAR data (LIRIC) were used in order to validate the mass concentration profiles estimated by the air quality model CAMx. LIDAR and CIMEL measurements of the Laboratory of Atmospheric Physics of the Aristotle University of Thessaloniki were used for this validation.The aerosol mass concentration profiles of the fine and coarse mode derived by CAMx were compared with the respective profiles derived by the retrieval algorithm. For the coarse mode particles, forecasts of the Saharan dust transportation model BSC-DREAM8bV2 were also taken into account. Each of the retrieval algorithm's profiles were matched to the models' profile with the best agreement within a time window of four hours before and after the central measurement. OPAC, a software than can provide optical properties of aerosol mixtures, was also employed in order to calculate the angstrom exponent and the lidar ratio values for 355nm and 532nm for each of the model's profiles aiming in a comparison with the angstrom exponent and the lidar ratio values derived by the retrieval algorithm for each measurement. The comparisons between the fine mode aerosol concentration profiles resulted in a good agreement between CAMx and the retrieval algorithm, with the vertical mean bias error never exceeding 7 μgr/m3. Concerning the aerosol coarse mode concentration profiles both CAMx and BSC-DREAM8bV2 values are severely underestimated, although, in cases of Saharan dust transportation events there is an agreement between the profiles of BSC-DREAM8bV2 model and the retrieval algorithm.

  4. Organic aerosols

    SciTech Connect

    Penner, J.E.

    1994-01-01

    Organic aerosols scatter solar radiation. They may also either enhance or decrease concentrations of cloud condensation nuclei. This paper summarizes observed concentrations of aerosols in remote continental and marine locations and provides estimates for the sources of organic aerosol matter. The anthropogenic sources of organic aerosols may be as large as the anthropogenic sources of sulfate aerosols, implying a similar magnitude of direct forcing of climate. The source estimates are highly uncertain and subject to revision in the future. A slow secondary source of organic aerosols of unknown origin may contribute to the observed oceanic concentrations. The role of organic aerosols acting as cloud condensation nuclei (CCN) is described and it is concluded that they may either enhance or decrease the ability of anthropogenic sulfate aerosols to act as CCN.

  5. Concentrations and Fluxes of Water-Soluble Reactive Nitrogen Gases and Aerosol Compounds Above a Forest Canopy

    NASA Astrophysics Data System (ADS)

    Wolff, V.; Trebs, I.; Moravek, A.; Zhu, Z.; Meixner, F. X.

    2008-12-01

    In summer 2007 we measured concentration gradients of NH3, HNO3, HONO and related aerosol species NH4+ and NO3- as well as SO2, and aerosol SO42- above a spruce canopy in south-east Germany (50° 09"N, 11° 52"E, 775m asl). Measurements were performed as part of an intensive observation period within the framework of the EGER (ExchanGE processes in mountainous Regions) project. NH3, HNO3, HONO, SO2, aerosol NH4+, aerosol NO3-, and aerosol SO42- were measured using the Gradient Analyzer for Aerosols and Gases, mounted on a tower. Water-soluble gases and aerosol species were collected simultaneously at two different heights by two rotating wet-annular denuders and two Steam-Jet Aerosol Collectors, respectively. Samples were analysed on-line via ion chromatography and flow injection analysis. To our knowledge this was the first time that these gas and aerosol species were measured simultaneously and with high time resolution (30 min) above a forest canopy. Data accuracy and precision is provided by a rigorous data screening, including the use of an internal standard, careful error estimation and repeated in- field blanks. Gradient precision of the measurements are derived from extended periods of side-by-side sampling of the sample boxes (n = 257). NH3 mixing ratios reached their maximum in the late afternoon with 2 to 3 ppb and their minimum in morning hours with 0.25 ppb, whereas aerosol NH4+ mirrored this behaviour with maximum values late night and early morning with 4 up to 8 ppb and minimum values in the afternoon, around 0.5 ppb and less. HNO3 and aerosol NO3- diel cycles also mirrored each other, HNO3 maxima during late afternoon ( above 1 ppb) and minimum during night and early morning with less than 0.2 ppb and aerosol NO3- maxima during night ( around 2 ppb, up to 6 ppb) and minima during afternoons with 0.5 ppb. Patterns of aerosol NH4+ and aerosol NO3- in the time series are apparently closely related. NH3 gradients indicate bidirectional fluxes, whereas

  6. Aerosol number size distributions in the lower troposphere over a background region and megalopolis (Novosibirsk) on result of airborne sounding in 2011-2013

    NASA Astrophysics Data System (ADS)

    Belan, Boris D.; Kozlov, Artem V.; Simonenkov, Denis V.; Tolmachev, Gennadii N.; Tsaruk, Victoria V.

    2014-11-01

    In this paper we present a comparison of the data on aerosol number size distribution measured with GRIMM 1.109 aerosol spectrometer in the lower troposphere over Novosibirsk and background area 150 km south-west of it during research flights of Optik TU-134 aircraft laboratory carried out along the route Novosibirsk - Ordynskoye - Novosibirsk in 2011-2013. Aerosol number size distributions averaged over 3 years as together so for warm and cold seasons separately are considered here. It is shown that the accumulation of anthropogenic aerosol within the BL over the city is typical for the cold period, which is most likely caused by inversions those are rapidly destroyed by vertical mixing during warm season and anthropogenic aerosols from the city are transported into the free troposphere.

  7. [Ultrafine particle number concentration and size distribution of vehicle exhaust ultrafine particles].

    PubMed

    Lu, Ye-qiang; Chen, Qiu-fang; Sun, Zai; Cai, Zhi-liang; Yang, Wen-jun

    2014-09-01

    Ultrafine particle (UFP) number concentrations obtained from three different vehicles were measured using fast mobility particle sizer (FMPS) and automobile exhaust gas analyzer. UFP number concentration and size distribution were studied at different idle driving speeds. The results showed that at a low idle speed of 800 rmin-1 , the emission particle number concentration was the lowest and showed a increasing trend with the increase of idle speed. The majority of exhaust particles were in Nuclear mode and Aitken mode. The peak sizes were dominated by 10 nm and 50 nm. Particle number concentration showed a significantly sharp increase during the vehicle acceleration process, and was then kept stable when the speed was stable. In the range of 0. 4 m axial distance from the end of the exhaust pipe, the particle number concentration decayed rapidly after dilution, but it was not obvious in the range of 0. 4-1 m. The number concentration was larger than the background concentration. Concentration of exhaust emissions such as CO, HC and NO showed a reducing trend with the increase of idle speed,which was in contrast to the emission trend of particle number concentration. PMID:25518646

  8. Gravity-wave effects on tracer gases and stratospheric aerosol concentrations during the 2013 ChArMEx campaign

    NASA Astrophysics Data System (ADS)

    Chane Ming, Fabrice; Vignelles, Damien; Jegou, Fabrice; Berthet, Gwenael; Renard, Jean-Baptiste; Gheusi, François; Kuleshov, Yuriy

    2016-07-01

    Coupled balloon-borne observations of Light Optical Aerosol Counter (LOAC), M10 meteorological global positioning system (GPS) sondes, ozonesondes, and GPS radio occultation data, are examined to identify gravity-wave (GW)-induced fluctuations on tracer gases and on the vertical distribution of stratospheric aerosol concentrations during the 2013 ChArMEx (Chemistry-Aerosol Mediterranean Experiment) campaign. Observations reveal signatures of GWs with short vertical wavelengths less than 4 km in dynamical parameters and tracer constituents, which are also correlated with the presence of thin layers of strong local enhancements of aerosol concentrations in the upper troposphere and the lower stratosphere. In particular, this is evident from a case study above Ile du Levant (43.02° N, 6.46° E) on 26-29 July 2013. Observations show a strong activity of dominant mesoscale inertia GWs with horizontal and vertical wavelengths of 370-510 km and 2-3 km respectively, and periods of 10-13 h propagating southward at altitudes of 13-20 km during 27-28 July. The European Centre for Medium-Range Weather Forecasts (ECMWF) analyses also show evidence of mesoscale inertia GWs with similar horizontal characteristics above the eastern part of France. Ray-tracing experiments indicate the jet-front system as the main source of observed GWs. Using a simplified linear GW theory, synthetic vertical profiles of dynamical parameters with large stratospheric vertical wind maximum oscillations of ±40 mms-1 are produced for the dominant mesoscale GW observed at heights of 13-20 km. Parcel advection method reveals signatures of GWs in the ozone mixing ratio and the tropospheric-specific humidity. Simulated vertical wind perturbations of the dominant GWs and small-scale perturbations of aerosol concentration (aerosol size of 0.2-0.7 µm) are revealed to be in phase in the lower stratosphere. Present results support the importance of vertical wind perturbations in the GW-aerosol relationship

  9. Opposite seasonality of the aerosol optical depth and the surface particulate matter concentration over the north China Plain

    NASA Astrophysics Data System (ADS)

    Qu, Wenjun; Wang, Jun; Zhang, Xiaoye; Sheng, Lifang; Wang, Wencai

    2016-02-01

    Great difference exists in the aerosol optical depth (AOD) between summer and winter over the North China Plain (NCP). Monthly mean AOD at 550 nm derived from the MODIS (MODerate Resolution Imaging Spectroradiometer) products during 2000-2014 over the area of 30-40° N and 110-125° E exhibits an annual maximum in June (0.855 ± 0.130) and a minimum in December (0.381 ± 0.032). This seasonality of AOD is in the opposite phase with the surface particulate matter (PM) concentration (higher in winter and lower in summer). The possible causes for the higher AOD in June (compared with December) include (a) a higher boundary layer height (BLH) that results in more efficient transport and mixing of aerosol particles to a higher altitude (corresponding to a lower particle concentration near surface) as revealed by the Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observations profile, (b) a higher relative humidity (RH) due to the inshore monsoon circulation that leads to enhancement of aerosol extinction, (c) emission from the regional open stalk burning in the summer harvest season (as seen from MODIS fire products), and (d) the typical eastward open topographical basin over NCP. Under the assumption that the aerosol and water vapor are well mixed within the boundary layer, analysis on multi-year average shows that the differences in BLH, RH and surface PM concentration can explain up to 81% of the variance of monthly averaged AOD over NCP. A preliminarily hypothesis is also suggested to interpret the shift of AOD pattern from winter to summer with an abrupt increase of AOD from May to June, as well as an increase of surface PM2.5 concentration over NCP during the early phase of northward progress of the East Asia summer monsoon front.

  10. Development and Validation of a Model to Predict Aerosol Breathing Zone Concentrations During Common Outdoor Activities

    EPA Science Inventory

    Research has been conducted on aerosol emission rates during various activities as well as aerosol transport into the breathing zone under idealized conditions. However, there has been little effort to link the two into a model for predicting a person’s breathing zone concentrat...

  11. Use of satellite-based aerosol optical depth and spatial clustering to predict ambient PM2.5 concentrations.

    PubMed

    Lee, Hyung Joo; Coull, Brent A; Bell, Michelle L; Koutrakis, Petros

    2012-10-01

    Satellite-based PM(2.5) monitoring has the potential to complement ground PM(2.5) monitoring networks, especially for regions with sparsely distributed monitors. Satellite remote sensing provides data on aerosol optical depth (AOD), which reflects particle abundance in the atmospheric column. Thus AOD has been used in statistical models to predict ground-level PM(2.5) concentrations. However, previous studies have shown that AOD may not be a strong predictor of PM(2.5) ground levels. Another shortcoming of remote sensing is the large number of non-retrieval days (i.e., days without satellite data available) due to clouds and snow- and ice-cover. In this paper we propose statistical approaches to overcome these two shortcomings, thereby making satellite imagery a viable method to estimate PM(2.5) concentrations. First, we render AOD a robust predictor of PM(2.5) mass concentration by introducing an AOD daily calibration approach through the use of mixed effects model. Second, we develop models that combine AOD and ground monitoring data to predict PM(2.5) concentrations during non-retrieval days. A key feature of this approach is that we develop these prediction models separately for groups of days defined by the observed amount of spatial heterogeneity in concentrations across the study region. Subsequently, these methodologies were applied to examine the spatial and temporal patterns of daily PM(2.5) concentrations for both retrieval days (i.e., days with satellite data available) and non-retrieval days in the New England region of the United States during the period 2000-2008. Overall, for the years 2000-2008, our statistical models predicted surface PM(2.5) concentrations with reasonably high R(2) (0.83) and low percent mean relative error (3.5%). Also the spatial distribution of the estimated PM(2.5) levels in the study domain clearly exhibited densely populated and high traffic areas. The method we have developed demonstrates that remote sensing can have a

  12. The effect of dry and wet deposition of condensable vapors on secondary organic aerosols concentrations over the continental US

    NASA Astrophysics Data System (ADS)

    Knote, C.; Hodzic, A.; Jimenez, J. L.

    2014-05-01

    The effect of dry and wet deposition of semi-volatile organic compounds (SVOC) in the gas-phase on the concentrations of secondary organic aerosol (SOA) is reassessed using recently derived water solubility information. The water solubility of SVOCs was implemented as a function of their volatility distribution within the regional chemistry transport model WRF-Chem, and simulations were carried out over the continental United States for the year 2010. Results show that including dry and wet removal of gas-phase SVOCs reduces annual average surface concentrations of anthropogenic and biogenic SOA by 48% and 63% respectively over the continental US Dry deposition of gas-phase SVOCs is found to be more effective than wet deposition in reducing SOA concentrations (-40% vs. -8% for anthropogenics, -52% vs. -11% for biogenics). Reductions for biogenic SOA are found to be higher due to the higher water solubility of biogenic SVOCs. The majority of the total mass of SVOC + SOA is actually deposited via the gas-phase (61% for anthropogenics, 76% for biogenics). A number of sensitivity studies shows that this is a robust feature of the modeling system. Other models that do not consider dry and wet removal of gas-phase SVOCs would hence overestimate SOA concentrations by roughly 50%. Assumptions about the water solubility of SVOCs made in some current modeling systems (H* = 105 M atm-1; H* = H* (HNO3)) still lead to an overestimation of 25% / 10% compared to our best estimate. A saturation effect is observed for Henry's law constants above 108 M atm-1, suggesting an upper bound of reductions in surface level SOA concentrations by 60% through removal of gas-phase SVOCs. Considering reactivity of gas-phase SVOCs in the dry deposition scheme was found to be negligible. Further sensitivity studies where we reduce the volatility of organic matter show that consideration of gas-phase SVOC removal still reduces average SOA concentrations by 31% on average. We consider this a lower

  13. The effect of dry and wet deposition of condensable vapors on secondary organic aerosols concentrations over the continental US

    DOE PAGESBeta

    Knote, C.; Hodzic, A.; Jimenez, J. L.

    2014-05-26

    The effect of dry and wet deposition of semi-volatile organic compounds (SVOC) in the gas-phase on the concentrations of secondary organic aerosol (SOA) is reassessed using recently derived water solubility information. The water solubility of SVOCs was implemented as a function of their volatility distribution within the regional chemistry transport model WRF-Chem, and simulations were carried out over the continental United States for the year 2010. Results show that including dry and wet removal of gas-phase SVOCs reduces annual average surface concentrations of anthropogenic and biogenic SOA by 48% and 63% respectively over the continental US Dry deposition of gas-phasemore » SVOCs is found to be more effective than wet deposition in reducing SOA concentrations (−40% vs. −8% for anthropogenics, −52% vs. −11% for biogenics). Reductions for biogenic SOA are found to be higher due to the higher water solubility of biogenic SVOCs. The majority of the total mass of SVOC + SOA is actually deposited via the gas-phase (61% for anthropogenics, 76% for biogenics). A number of sensitivity studies shows that this is a robust feature of the modeling system. Other models that do not consider dry and wet removal of gas-phase SVOCs would hence overestimate SOA concentrations by roughly 50%. Assumptions about the water solubility of SVOCs made in some current modeling systems (H* = 105 M atm−1; H* = H* (HNO3)) still lead to an overestimation of 25% / 10% compared to our best estimate. A saturation effect is observed for Henry's law constants above 108 M atm−1, suggesting an upper bound of reductions in surface level SOA concentrations by 60% through removal of gas-phase SVOCs. Considering reactivity of gas-phase SVOCs in the dry deposition scheme was found to be negligible. Further sensitivity studies where we reduce the volatility of organic matter show that consideration of gas-phase SVOC removal still reduces average SOA concentrations by 31% on average. We

  14. Organic aerosol processing in tropical deep convective clouds: Development of a new model (CRM-ORG) and implications for sources of particle number

    NASA Astrophysics Data System (ADS)

    Murphy, B. N.; Julin, J.; Riipinen, I.; Ekman, A. M. L.

    2015-10-01

    The difficulty in assessing interactions between atmospheric particles and clouds is due in part to the chemical complexity of the particles and to the wide range of length and timescales of processes occurring simultaneously during a cloud event. The new Cloud-Resolving Model with Organics (CRM-ORG) addresses these interactions by explicitly predicting the formation, transport, uptake, and re-release of surrogate organic compounds consistent with the volatility basis set framework within a nonhydrostatic, three-dimensional cloud-resolving model. CRM-ORG incorporates photochemical production, explicit condensation/evaporation of organic and inorganic vapors, and a comprehensive set of four different mechanisms describing particle formation from organic vapors and sulfuric acid. We simulate two deep convective cloud events over the Amazon rain forest in March 1998 and compare modeled particle size distributions with airborne observations made during the time period. The model predictions agree well with the observations for Aitken mode particles in the convective outflow (10-14 km) but underpredict nucleation mode particles by a factor of 20. A strong in-cloud particle formation process from organic vapors alone is necessary to reproduce even relatively low ultrafine particle number concentrations (~1500 cm-3). Sensitivity tests with variable initial aerosol loading and initial vertical aerosol profile demonstrate the complexity of particle redistribution and net gain or loss in the cloud. In-cloud particle number concentrations could be enhanced by as much as a factor of 3 over the base case simulation in the cloud outflow but were never reduced by more than a factor of 2 lower than the base. Additional sensitivity cases emphasize the need for constrained estimates of surface tension and affinity of organic vapors to ice surfaces. When temperature-dependent organic surface tension is introduced to the new particle formation mechanisms, the number concentration of

  15. Comparison of Satellite Observations of Aerosol Optical Depth to Surface Monitor Fine Particle Concentration

    NASA Technical Reports Server (NTRS)

    Kleb, Mary M.; AlSaadi, Jassim A.; Neil, Doreen O.; Pierce, Robert B.; Pippin, Margartet R.; Roell, Marilee M.; Kittaka, Chieko; Szykman, James J.

    2004-01-01

    Under NASA's Earth Science Applications Program, the Infusing satellite Data into Environmental Applications (IDEA) project examined the relationship between satellite observations and surface monitors of air pollutants to facilitate a more capable and integrated observing network. This report provides a comparison of satellite aerosol optical depth to surface monitor fine particle concentration observations for the month of September 2003 at more than 300 individual locations in the continental US. During September 2003, IDEA provided prototype, near real-time data-fusion products to the Environmental Protection Agency (EPA) directed toward improving the accuracy of EPA s next-day Air Quality Index (AQI) forecasts. Researchers from NASA Langley Research Center and EPA used data from the Moderate Resolution Imaging Spectroradiometer (MODIS) instrument combined with EPA ground network data to create a NASA-data-enhanced Forecast Tool. Air quality forecasters used this tool to prepare their forecasts of particle pollution, or particulate matter less than 2.5 microns in diameter (PM2.5), for the next-day AQI. The archived data provide a rich resource for further studies and analysis. The IDEA project uses data sets and models developed for tropospheric chemistry research to assist federal, state, and local agencies in making decisions concerning air quality management to protect public health.

  16. Aerosol-OT-gamma-alumina admicelles for the concentration of hydrophobic organic compounds in water.

    PubMed

    Saitoh, Tohru; Matsushima, Seiichi; Hiraide, Masataka

    2004-06-25

    A novel admicelle composing of a dialkylated anionic surfactant, di-2-ethylhexyl sodium sulfosuccinate (Aerosol-OT, AOT) and gamma-alumina was prepared by mixing them in acidic aqueous solution. The amount of the maximum sorption of AOT on 1 g of alumina at pH 2 was ca. 130 mg. By comparing the fluorescence spectra of N-phenyl-1-naphthylamine in different solvents, the solvent property of AOT-gamma-alumina admicelles was corresponding to that of toluene or diethyl ether. Thus, the AOT-gamma-alumina admicelles had greater hydrophobicity than SDS-gamma-alumina admicelles having similar hydrophobicity to 1-octanol or ethyl acetate. Hydrophobic organic compounds, chlorophenols having more than three chloro substituents, octylphenol, nonylphenol, dibutyl phthalate was almost quantitatively (98% or more) collected onto AOT admicelles composing of 1.5 g gamma-alumina and 150 mg AOT. The greater collection yields rather than those in SDS-admicellar system were ascribable to greater hydrophobicity and stability of AOT admicelles. After the 500-fold concentration, traces (nM) of organic contaminants in water samples were successfully detected with an HPLC having a photometric detector. PMID:15230525

  17. Hourly elemental concentrations in PM2.5 aerosols sampled simultaneously at urban background and road site

    NASA Astrophysics Data System (ADS)

    Dall'Osto, M.; Querol, X.; Amato, F.; Karanasiou, A.; Lucarelli, F.; Nava, S.; Calzolai, G.; Chiari, M.

    2012-08-01

    Hourly-resolved aerosol chemical speciation data can be a highly powerful tool to determine the source origin of atmospheric pollutants in urban Environments. Aerosol mass concentrations of seventeen elements (Na, Mg, Al, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Sr and Pb) were obtained by time (1 h) and size (PM2.5 particulate matter <2.5 μm) resolved Particle Induced X-ray Emission (PIXE) measurements. In the Marie Curie FP7-EU framework of SAPUSS (Solving Aerosol Problems by Using Synergistic Strategies), the unique approach used is the simultaneous PIXE measurements at two monitoring sites: urban background (UB) and a street canyon traffic road site (RS). Elements related to primary non exhaust traffic emission (Fe, Cu), dust resuspension (Ca) and anthropogenic Cl were found enhanced at the RS, whereas industrial related trace metals (Zn, Pb, Mn) were found at higher concentrations at the more ventilated UB site. When receptor modelling was performed with positive matrix factorization (PMF), nine different aerosol sources were identified at both sites: three types of regional aerosols (secondary sulphate (S) - 27%, biomass burning (K) - 5%, sea salt (Na-Mg) - 17%), three types of dust aerosols (soil dust (Al-Ti) - 17%, urban crustal dust (Ca) - 6%, and primary traffic non exhaust brake dust (Fe-Cu) - 7%), and three types industrial aerosol plumes-like events (shipping oil combustion (V-Ni) - 17%, industrial smelters (Zn-Mn) - 3%, and industrial combustion (Pb-Cl) - 5%). The validity of the PMF solution of the PIXE data is supported by strong correlations with external single particle mass spectrometry measurements. Beside apportioning the aerosol sources, some important air quality related conclusions can be drawn about the PM2.5 fraction simultaneously measured at the UB and RS sites: (1) the regional aerosol sources impact both monitoring sites at similar concentrations regardless their different ventilation conditions; (2) by contrast, local industrial

  18. Solar concentration properties of flat fresnel lenses with large F-numbers

    NASA Technical Reports Server (NTRS)

    Cosby, R. M.

    1978-01-01

    The solar concentration performances of flat, line-focusing sun-tracking Fresnel lenses with selected f-numbers between 0.9 and 2.0 were analyzed. Lens transmittance was found to have a weak dependence on f-number, with a 2% increase occuring as the f-number is increased from 0.9 to 2.0. The geometric concentration ratio for perfectly tracking lenses peaked for an f-number near 1.35. Intensity profiles were more uniform over the image extent for large f-number lenses when compared to the f/0.9 lens results. Substantial decreases in geometri concentration ratios were observed for transverse tracking errors equal to or below 1 degree for all f-number lenses. With respect to tracking errors, the solar performance is optimum for f-numbers between 1.25 and 1.5.

  19. Studying the concentration dependence of the aggregation number of a micellar model system by SANS.

    PubMed

    Amann, Matthias; Willner, Lutz; Stellbrink, Jörg; Radulescu, Aurel; Richter, Dieter

    2015-06-01

    We present a small-angle neutron scattering (SANS) structural characterization of n-alkyl-PEO polymer micelles in aqueous solution with special focus on the dependence of the micellar aggregation number on increasing concentration. The single micellar properties in the dilute region up to the overlap concentration ϕ* are determined by exploiting the well characterized unimer exchange kinetics of the model system in a freezing and diluting experiment. The micellar solutions are brought to thermodynamic equilibrium at high temperatures, where unimer exchange is fast, and are then cooled to low temperatures and diluted to concentrations in the limit of infinite dilution. At low temperatures the kinetics, and therefore the key mechanism for micellar rearrangement, is frozen on the experimental time scale, thus preserving the micellar structure in the dilution process. Information about the single micellar structure in the semidilute and concentrated region are extracted from structure factor analysis at high concentrations where the micelles order into fcc and bcc close packed lattices and the aggregation number can be calculated by geometrical arguments. This approach enables us to investigate the aggregation behavior in a wide concentration regime from dilute to 6·ϕ*, showing a constant aggregation number with concentration over a large concentration regime up to a critical concentration about three times ϕ*. When exceeding this critical concentration, the aggregation number was found to increase with increasing concentration. This behavior is compared to scaling theories for star-like polymer micelles. PMID:25892401

  20. Influence of the East Asian winter monsoon on interannual variations of wintertime aerosol concentrations over East Asia during 1980-2013

    NASA Astrophysics Data System (ADS)

    Jeong, Jaein; Park, Rokjin

    2016-04-01

    The monsoon circulation influence the spatial and temporal variations of aerosol concentrations. In this study, we examine the effect of the East Asian winter monsoon (EAWM) on wintertime aerosol concentrations in East Asia during 1980-2013 using observed PM10 concentrations and a global 3-D chemical transport model (GEOS-Chem) driven by the assimilated MERRA meteorological data. We find that the observed and simulated surface aerosol concentrations have strong negative (positive) correlations with the EAWM over the northeast (southeast) Asia. Differences in aerosol concentrations between the strong and weak monsoon years are up to 25% over the northeast Asia (30°-55°N, 110°-160°E), where the strong monsoon years show much lower aerosol concentrations than those of the weak monsoon years. On the other hand, the opposite patterns are found over the southeast Asia (20°-30°N, 110°-160°E). The EAWM appears to play a significant role in the inter-annual variability of aerosol concentrations and thus its change would be crucial to predict wintertime aerosol concentrations and their future changes over East Asia.

  1. Mathematical model describing thickness changes of concentration boundary layers controlled by polymeric membrane parameters and concentration Rayleigh number.

    PubMed

    Slezak, Andrzej; Slezak, Izabella; Bryll, Arkadiusz; Jasik-Slezak, Jolanta; Młynarski, Jacek

    2006-01-01

    In the paper, by applicating the classic definition of concentration Rayleigh number and the second Kedem-Katchalsky equation, there was deriven the equation of the fourth degree, which makes thicknesses (deltah and deltal) dependent on the concentration difference (Ch-Cl), concentration Rayleigh number (Rc), membrane permeability parameters (omega, xi s) and solutions (Dl, Dh), physico-chemical parameters of solutions (v(l), v(h), rho l, rho h, delta rho/deltaC), temperature (T) and gravitational acceleration (g). On the basis of the obtained formula for isothermal conditions (T = const) and constant gravitational field (g = const), there were calculated non-linear dependencies delta h = f(Ch-Cl)(Rc, zeta s), delta h = f (Rc)((Ch-Cl),zeta s) and delta h = f(delta s)((Ch-Cl),Rc). PMID:16869546

  2. [Variation of atmospheric particle number concentrations in Qingdao and its impact on visibility].

    PubMed

    Ke, Xin-Shu; Sheng, Li-Fang; Kong, Jun; Hao, Ze-Tong; Qu, Wen-Jun

    2014-01-01

    Atmospheric particle number concentrations were measured from September 2010 to August 2011 with potable light house laser particle counter to study the variation of atmospheric particle concentrations and its impact on visibility in Qingdao. Backward trajectory was calculated by Hysplit model. Statistical analysis was done to discuss the influence of meteorological factors on the atmospheric particle number concentrations and visibility. It was shown that the atmospheric particle number concentrations were the highest in winter and spring, followed by autumn, and the lowest in summer. Air mass from Xinjiang and Gansu regions resulted in higher particle concentrations, while the atmospheric particles from the northeast and the ocean had lower concentrations. The variation of atmospheric particle number concentrations presented a good negative correlation with the variation of wind speed, relative humidity and mixed-layer height. When the air mass came from west or northwest, the surface wind direction was south or southeast and the mixed-layer height was low, the number concentration of fine particles was likely to be higher, which tended to cause low visibility phenomenon. PMID:24720179

  3. Outdoor and indoor aerosol size, number, mass and compositional dynamics at an urban background site during warm season

    NASA Astrophysics Data System (ADS)

    Talbot, N.; Kubelova, L.; Makes, O.; Cusack, M.; Ondracek, J.; Vodička, P.; Schwarz, J.; Zdimal, V.

    2016-04-01

    This paper describes the use of a unique valve switching system that allowed for high temporal resolution indoor and outdoor data to be collected concurrently from online C-ToF-AMS, SMPS and OC/EC, and offline BLPI measurements. The results reveal near real-time dynamic aerosol behaviour along a migration path from an outdoor to indoor environment. An outdoor reduction in NR-PM1 mass concentration occurred daily from AM (06:00-12:00) to PM (12:00-18:00). SO4 (26%-37%) [AM/PM] increased proportionally during afternoons at the expense of NO3 (18%-7%). The influences of mixing height, temperature and solar radiation were considered against the mean mass concentration loss for each species. Losses were then calculated according to species via a basic input/output model. NO3 lost the most mass during afternoon periods, which we attribute to the accelerated dissociation of NH4NO3 through increasing temperature and decreasing relative humidity. Indoor/outdoor (I/O) ratios varied from 0.46 for <40 nm to 0.65 for >100 nm. These ratios were calculated using average SMPS PNC measurements over the full campaign and corroborated using a novel technique of calculating I/O penetration ratios through the indoor migration of particles during a new particle formation event. This ratio was then used to observe changes in indoor composition relative to those outdoors. Indoor sampling was carried out in an undisturbed room with no known sources. Indoor concentrations were found to be proportional to those outdoors, with organic matter [2.7 μg/m3] and SO4 [1.7 μg/m3] being the most prominent species. These results are indicative of fairly rapid aerosol penetration, a source-free indoor environment and small afternoon I/O temperature gradients. Fine fraction NO3 was observed indoors in both real-time AMS PM1 and off-line BLPI measurements. Greater mass concentration losses were observed from filter measurements, highlighting an important time dependency factor when investigating semi

  4. Diurnal and seasonal variations of meteorology and aerosol concentrations in the foothills of the nepal himalayas (Nagarkot: 1,900 m asl)

    NASA Astrophysics Data System (ADS)

    Shrestha, Rudra K.; Gallagher, Martin W.; Connolly, Paul J.

    2016-02-01

    A 10-months long monitoring experiment to investigate the diurnal and seasonal variation of aerosol size distribution at Nagarkot (1,900 m asl) in the Kathmadu Valley was carried out as part of a study on katabatic and anabatic influence on pollution dispersion mechanisms. Seasonal means show total aerosol number concentration was highest during post-monsoon season (775 ± 417 cm-3) followed by pre-monsoon (644 ± 429 cm-3) and monsoon (293 ± 205 cm-3) periods. Fine particle concentration (0.25 μm ≤ DP ≤ 2.5 μm) dominated in all seasons, however, contribution by coarse particles (3.0 μm ≤ DP ≤ 10.0 μm) is more significant in the monsoon season with contributions from particles larger than 10.0 μm being negligible. Our results show a regular diurnal pattern of aerosol concentration in the valley with a morning and an evening peak. The daily twin peaks are attributed to calm conditions followed by transitional growth and break down of the valley boundary layer below. The peaks are generally associated with enhancement of the coarse particle fraction. The evening peak is generally higher than the morning peak, and is caused by fresh evening pollution from the valley associated with increased local activities coupled with recirculation of these trapped pollutants. Relatively clean air masses from neighbouring valleys contribute to the smaller morning peak. Gap flows through the western passes of the Kathmandu Valley, which sweep away the valley pollutants towards the eastern passes modulated by the mountain - valley wind system, are mainly responsible for the dominant pollutant circulation patterns exhibited within the valley.

  5. Using MAIAC Aerosol Products to Estimate PM10 Concentrations in the Southeastern U.S

    NASA Astrophysics Data System (ADS)

    Jinnagara Puttaswamy, S.; Hu, X.; Lyapustin, A.; Wang, Y.; Liu, Y.

    2012-12-01

    Acute and chronic exposure to particulate matter has been linked to various adverse health effects. High PM levels including inhalable particles (PM10) and fine particles (PM2.5) are commonly found in large urban centers in the developing world. Unlike PM2.5 whose routine ground monitoring is very sparse, PM10 is regularly measured in many large cities in developing countries. In this analysis, we evaluate the potential for satellite aerosol remote sensing product to estimate PM10 levels. We chose AOD values in 2003 retrieved by the Multiangle Implementation of Atmospheric Correction (MAIAC) algorithm based on MODIS measurements, which has a high spatial resolution of 1 km. Our study area is a 600 km x 600 km region centered in Atlanta, GA. Linear mixed effect (LME) models were developed with MAIAC AOD as the primary predictor variable, meteorology, PM10 emission locations and land use variables as secondary predictor variables. Daily PM10 concentrations measured at ~70 EPA air quality monitoring stations were used as the dependent variable. Model day of year was used as the grouping factor for the random effect of MAIAC AOD. We aggregated AOD and other covariates on 1 km, 3km, 5km and 10km resolution grids and similar LME models were developed for each spatial resolution to compare their abilities to capture the spatial patterns of PM10 mass concentrations at various scales. Our models show that MAIAC AOD, temperature, wind speed and PM 10 emissions source locations are statistically significant predictors of PM 10 at all the spatial scales. Model fitting R2 ranges from 0.35 in winter to 0.56 in the summer. Model performances show a slight decline as the grid resolution decreases. Although the performances of PM10 exposure models are not as good as those of PM2.5 models reported in the literature, these models can still provide spatially resolved PM10 levels at urban scale, which would enable preliminary PM10-related public health research in developing countries.

  6. Multicellular natural convection of a low Prandlt number fluid between horizontal concentric cylinders

    SciTech Connect

    Joosik Yoo; Jun Young Choi; Moonuhn Kim . Dept. of Mechanical Engineering)

    1994-01-01

    Two-dimensional natural convection of a fluid of low Prandtl number (Pr = 0.02) in an annulus between two concentric horizontal cylinders is numerically investigated in a wide range of gap widths. For low Grashof numbers, a steady unicellular convection is obtained. Above a transition Grashof number that depends on the gap width, a steady bicellular flow occurs. With further increase of the Grashof number, steady or time-periodic multicellular convection occurs, and finally, complex unsteady convective flow appears. A plot is presented that predicts the type of flow patterns for various combination of gap widths and Grashof numbers.

  7. Characterisation of sub-micron particle number concentrations and formation events in the western Bushveld Igeneous Complex, South Africa

    NASA Astrophysics Data System (ADS)

    Hirsikko, A.; Vakkari, V.; Tiitta, P.; Manninen, H. E.; Gagné, S.; Laakso, H.; Kulmala, M.; Mirme, A.; Mirme, S.; Mabaso, D.; Beukes, J. P.; Laakso, L.

    2012-01-01

    South Africa holds significant mineral resources, with a substantial fraction of these reserves occurring in a large geological structure termed the Bushveld Igeneous Complex (BIC). The majority of the world's platinum group metals (PGMs) and chromium originate from the BIC. Considering the importance of PGMs in the manufacturing of automotive catalytic converters, as well as the relatively poor current state of air quality and the general lack of atmospheric research in the BIC, atmospheric related research in this geographical area is of local (South African) and of international interest. The western limb of the BIC is the most exploited, with at least eleven pyrometallurgical smelters occurring within a 55 km radius. Due to the lure of employment in the industrialised BIC, the area is populated by informal, semi-formal and formal residential developments. In order to investigate the characteristics and processes affecting sub-micron particle number concentrations and formation events, air ion and aerosol particle size distribution and concentration measurements were conducted for over two years at Marikana in the heart of the western BIC. Our results indicated that high amounts of Aitken and accumulation mode particles originated from domestic burning for heating and cooking in the morning and evening, while during daytime SO2-based nucleation (from industrial emissions) was the most probable source for large number concentrations of nucleation and Aitken mode particles. Nucleation event day frequency was extremely high, i.e. 86% of the analysed days, which to the knowledge of the authors is the highest frequency ever reported. Secondary particle formation was influenced both by local pollution sources and regional ambient conditions. Therefore, our observation of the annual cycle and magnitude of the particle formation and growth rates during nucleation events were similar to the results from a semi-clean savannah site in South Africa.

  8. Impact of clouds and precipitation on atmospheric aerosol

    NASA Astrophysics Data System (ADS)

    Andronache, Constantin

    2015-04-01

    Aerosols have a significant impact on the dynamics and microphysics of continental mixed-phase convective clouds. High aerosol concentrations provide enhanced cloud condensation nuclei that can lead to the invigoration of convection and increase of surface rainfall. Such effects are dependent on environmental conditions and aerosol properties. Clouds are not only affected by aerosol, they also alter aerosol properties by various processes. Cloud processing of aerosol includes: convective redistribution, modification in the number and size of aerosol particles, chemical processing, new particle formation around clouds, and aerosol removal by rainfall to the surface. Among these processes, the wet removal during intense rain events, in polluted continental regions, can lead to spikes in acidic deposition into environment. In this study, we address the effects of clouds and precipitation on the aerosol distribution in cases of convective precipitation events in eastern US. We examine the effects of clouds and precipitation on various aerosol species, as well as their temporal and spatial variability.

  9. Approximate Bayesian computation for estimating number concentrations of monodisperse nanoparticles in suspension by optical microscopy

    NASA Astrophysics Data System (ADS)

    Röding, Magnus; Zagato, Elisa; Remaut, Katrien; Braeckmans, Kevin

    2016-06-01

    We present an approximate Bayesian computation scheme for estimating number concentrations of monodisperse diffusing nanoparticles in suspension by optical particle tracking microscopy. The method is based on the probability distribution of the time spent by a particle inside a detection region. We validate the method on suspensions of well-controlled reference particles. We illustrate its usefulness with an application in gene therapy, applying the method to estimate number concentrations of plasmid DNA molecules and the average number of DNA molecules complexed with liposomal drug delivery particles.

  10. Aerosol Observing System (AOS) Handbook

    SciTech Connect

    Jefferson, A

    2011-01-17

    The Aerosol Observing System (AOS) is a suite of in situ surface measurements of aerosol optical and cloud-forming properties. The instruments measure aerosol properties that influence the earth’s radiative balance. The primary optical measurements are those of the aerosol scattering and absorption coefficients as a function of particle size and radiation wavelength and cloud condensation nuclei (CCN) measurements as a function of percent supersaturation. Additional measurements include those of the particle number concentration and scattering hygroscopic growth. Aerosol optical measurements are useful for calculating parameters used in radiative forcing calculations such as the aerosol single-scattering albedo, asymmetry parameter, mass scattering efficiency, and hygroscopic growth. CCN measurements are important in cloud microphysical models to predict droplet formation.

  11. CCN concentrations and BC warming influenced by maritime ship emitted aerosol plumes over southern Bay of Bengal.

    PubMed

    Ramana, M V; Devi, Archana

    2016-01-01

    Significant quantities of carbon soot aerosols are emitted into pristine parts of the atmosphere by marine shipping. Soot impacts the radiative balance of the Earth-atmosphere system by absorbing solar-terrestrial radiation and modifies the microphysical properties of clouds. Here we examined the impact of black carbon (BC) on net warming during monsoon season over southern Bay-of-Bengal, using surface and satellite measurements of aerosol plumes from shipping. Shipping plumes had enhanced the BC concentrations by a factor of four around the shipping lane and exerted a strong positive influence on net warming. Compiling all the data, we show that BC atmospheric heating rates for relatively-clean and polluted-shipping corridor locations to be 0.06 and 0.16 K/day respectively within the surface layer. Emissions from maritime ships had directly heated the lower troposphere by two-and-half times and created a gradient of around 0.1 K/day on either side of the shipping corridor. Furthermore, we show that ship emitted aerosol plumes were responsible for increase in the concentration of cloud condensation nuclei (CCN) by an order of magnitude that of clean air. The effects seen here may have significant impact on the monsoonal activity over Bay-of-Bengal and implications for climate change mitigation strategies. PMID:27480275

  12. CCN concentrations and BC warming influenced by maritime ship emitted aerosol plumes over southern Bay of Bengal

    PubMed Central

    Ramana, M. V.; Devi, Archana

    2016-01-01

    Significant quantities of carbon soot aerosols are emitted into pristine parts of the atmosphere by marine shipping. Soot impacts the radiative balance of the Earth-atmosphere system by absorbing solar-terrestrial radiation and modifies the microphysical properties of clouds. Here we examined the impact of black carbon (BC) on net warming during monsoon season over southern Bay-of-Bengal, using surface and satellite measurements of aerosol plumes from shipping. Shipping plumes had enhanced the BC concentrations by a factor of four around the shipping lane and exerted a strong positive influence on net warming. Compiling all the data, we show that BC atmospheric heating rates for relatively-clean and polluted-shipping corridor locations to be 0.06 and 0.16 K/day respectively within the surface layer. Emissions from maritime ships had directly heated the lower troposphere by two-and-half times and created a gradient of around 0.1 K/day on either side of the shipping corridor. Furthermore, we show that ship emitted aerosol plumes were responsible for increase in the concentration of cloud condensation nuclei (CCN) by an order of magnitude that of clean air. The effects seen here may have significant impact on the monsoonal activity over Bay-of-Bengal and implications for climate change mitigation strategies. PMID:27480275

  13. LIDAR technique: a central puzzle piece to build an integrated observation - modeling approach for air mass aerosols concentration evaluation

    NASA Astrophysics Data System (ADS)

    Tudose, Ovidiu-Gelu

    2013-04-01

    This paper presents a study of the temporal and vertical variation of mixed aerosol mass concentration near Bucharest during a dedicated observation campaign performed in summer 2012. To obtain the vertical mass concentrations profiles a combination of measured (mainly based on LIDAR technique) and modeled data was used. This method is based on the hypothesis that any mixture in the atmosphere can be described as a combination of low-depolarizing and high-depolarizing particles of a particular type. It uses the method proposed by Tesche et al. (2009), combined with forward simulations (i.e. OPAC). Based on supplementary information (e.g. preliminary assessment of aerosol source from forecast models and back trajectories) and several optical indicators (Angstrom exponent, LIDAR ratio, particle depolarization, AOD we built an approach to 2 cases of aerosol mixture, and validate the results using other information sources: sun photometry, forecasts, back trajectories. The first case was proved to be a smoke predominant layer, the second a Saharan dust predominant layer. Information from various data sources (DREAM, HYSPLIT, AERONET, MODIS) was consistent with our retrievals.

  14. CCN concentrations and BC warming influenced by maritime ship emitted aerosol plumes over southern Bay of Bengal

    NASA Astrophysics Data System (ADS)

    Ramana, M. V.; Devi, Archana

    2016-08-01

    Significant quantities of carbon soot aerosols are emitted into pristine parts of the atmosphere by marine shipping. Soot impacts the radiative balance of the Earth-atmosphere system by absorbing solar-terrestrial radiation and modifies the microphysical properties of clouds. Here we examined the impact of black carbon (BC) on net warming during monsoon season over southern Bay-of-Bengal, using surface and satellite measurements of aerosol plumes from shipping. Shipping plumes had enhanced the BC concentrations by a factor of four around the shipping lane and exerted a strong positive influence on net warming. Compiling all the data, we show that BC atmospheric heating rates for relatively-clean and polluted-shipping corridor locations to be 0.06 and 0.16 K/day respectively within the surface layer. Emissions from maritime ships had directly heated the lower troposphere by two-and-half times and created a gradient of around 0.1 K/day on either side of the shipping corridor. Furthermore, we show that ship emitted aerosol plumes were responsible for increase in the concentration of cloud condensation nuclei (CCN) by an order of magnitude that of clean air. The effects seen here may have significant impact on the monsoonal activity over Bay-of-Bengal and implications for climate change mitigation strategies.

  15. Aircraft measurements of ozone, NOx, CO, and aerosol concentrations in biomass burning smoke over Indonesia and Australia in October 1997: Depleted ozone layer at low altitude over Indonesia

    NASA Astrophysics Data System (ADS)

    Tsutsumi, Yukitomo; Sawa, Yousuke; Makino, Yukio; Jensen, Jørgen B.; Gras, John L.; Ryan, Brian F.; Diharto, Sri; Harjanto, Hery

    The 1997 El Niño unfolded as one of the most sever El Niño Southern Oscillation (ENSO) events in this century and it coincided with massive biomass burning in the equatorial western Pacific region. To assess the influence on the atmosphere, aircraft observations of trace gases and aerosol were conducted over Kalimantan in Indonesia and Australia. Over Kalimantan in Indonesia, high concentrations of O3, NOx, CO, and aerosols were observed during the flight. Although the aerosol and NOx decreased with altitude, the O3 had the maximum concentration (80.5 ppbv) in the middle layer of the smoke haze and recorded very low concentrations (˜20 ppbv) in the lower smoke layer. This feature was not observed in the Australian smoke. We proposed several hypotheses for the low O3 concentration at low levels over Kalimantan. The most likely are lack of solar radiation and losses at the surface of aerosol particles.

  16. The Potential of The Synergy of Sunphotometer and Lidar Data to Validate Vertical Profiles of The Aerosol Mass Concentration Estimated by An Air Quality Model

    NASA Astrophysics Data System (ADS)

    Siomos, N.; Filioglou, M.; Poupkou, A.; Liora, N.; Dimopoulos, S.; Melas, D.; Chaikovsky, A.; Balis, D. S.

    2016-06-01

    Vertical profiles of the aerosol mass concentration derived by the Lidar/Radiometer Inversion Code (LIRIC), that uses combined sunphotometer and lidar data, were used in order to validate the aerosol mass concentration profiles estimated by the air quality model CAMx. Lidar and CIMEL measurements performed at the Laboratory of Atmospheric Physics of the Aristotle University of Thessaloniki, Greece (40.5N, 22.9E) from the period 2013-2014 were used in this study.

  17. In situ formation and spatial variability of particle number concentration in a European megacity

    NASA Astrophysics Data System (ADS)

    Pikridas, M.; Sciare, J.; Freutel, F.; Crumeyrolle, S.; von der Weiden-Reinmüller, S.-L.; Borbon, A.; Schwarzenboeck, A.; Merkel, M.; Crippa, M.; Kostenidou, E.; Psichoudaki, M.; Hildebrandt, L.; Engelhart, G. J.; Petäjä, T.; Prévôt, A. S. H.; Drewnick, F.; Baltensperger, U.; Wiedensohler, A.; Kulmala, M.; Beekmann, M.; Pandis, S. N.

    2015-09-01

    Ambient particle number size distributions were measured in Paris, France, during summer (1-31 July 2009) and winter (15 January to 15 February 2010) at three fixed ground sites and using two mobile laboratories and one airplane. The campaigns were part of the Megacities: Emissions, urban, regional and Global Atmospheric POLlution and climate effects, and Integrated tools for assessment and mitigation (MEGAPOLI) project. New particle formation (NPF) was observed only during summer on approximately 50 % of the campaign days, assisted by the low condensation sink (about 10.7 ± 5.9 × 10-3 s-1). NPF events inside the Paris plume were also observed at 600 m altitude onboard an aircraft simultaneously with regional events identified on the ground. Increased particle number concentrations were measured aloft also outside of the Paris plume at the same altitude, and were attributed to NPF. The Paris plume was identified, based on increased particle number and black carbon concentration, up to 200 km away from the Paris center during summer. The number concentration of particles with diameters exceeding 2.5 nm measured on the surface at the Paris center was on average 6.9 ± 8.7 × 104 and 12.1 ± 8.6 × 104 cm-3 during summer and winter, respectively, and was found to decrease exponentially with distance from Paris. However, further than 30 km from the city center, the particle number concentration at the surface was similar during both campaigns. During summer, one suburban site in the NE was not significantly affected by Paris emissions due to higher background number concentrations, while the particle number concentration at the second suburban site in the SW increased by a factor of 3 when it was downwind of Paris.

  18. PASSIVE AEROSOL SAMPLER FOR CHARACTERIZATION, AMBIENT CONCENTRATION, AND PARTICLE SIZE MEASUREMENT

    EPA Science Inventory

    This is an extended abstract of a presentation made at the Air and Waste Management Association's Symposium on Air Quality Measurement Methods and Technology, Durham, NC, May 9-11, 2006. The abstract describes the theory, design, and initial testing of a passive aerosol sampler f...

  19. Trace Gas/Aerosol Boundary Concentrations and their Impacts on Continental-scale AQMEII Modelling Domains

    EPA Science Inventory

    Over twenty modeling groups are participating in the Air Quality Model Evaluation International Initiative (AQMEII) in which a variety of mesoscale photochemical and aerosol air quality modeling systems are being applied to continental-scale domains in North America and Europe fo...

  20. The importance of plume rise on the concentrations and atmospheric impacts of biomass burning aerosol

    NASA Astrophysics Data System (ADS)

    Walter, Carolin; Freitas, Saulo R.; Kottmeier, Christoph; Kraut, Isabel; Rieger, Daniel; Vogel, Heike; Vogel, Bernhard

    2016-07-01

    We quantified the effects of the plume rise of biomass burning aerosol and gases for the forest fires that occurred in Saskatchewan, Canada, in July 2010. For this purpose, simulations with different assumptions regarding the plume rise and the vertical distribution of the emissions were conducted. Based on comparisons with observations, applying a one-dimensional plume rise model to predict the injection layer in combination with a parametrization of the vertical distribution of the emissions outperforms approaches in which the plume heights are initially predefined. Approximately 30 % of the fires exceed the height of 2 km with a maximum height of 8.6 km. Using this plume rise model, comparisons with satellite images in the visible spectral range show a very good agreement between the simulated and observed spatial distributions of the biomass burning plume. The simulated aerosol optical depth (AOD) with data of an AERONET station is in good agreement with respect to the absolute values and the timing of the maximum. Comparison of the vertical distribution of the biomass burning aerosol with CALIPSO (Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation) retrievals also showed the best agreement when the plume rise model was applied. We found that downwelling surface short-wave radiation below the forest fire plume is reduced by up to 50 % and that the 2 m temperature is decreased by up to 6 K. In addition, we simulated a strong change in atmospheric stability within the biomass burning plume.

  1. Contribution of sulfate and organic aerosols to cloud condensation nuclei at Point Reyes, California

    SciTech Connect

    Rivera-Carpio, C.A.; Corrigan, C.E.; Novakov, T.; Penner, J.E.

    1995-12-01

    We have determined mass size distributions of major aerosol species by the Micro Orifice Uniform Deposit Impactor (MOUDI) and simultaneously measured aerosol number size distributions and CCN number concentrations (at 0.5% supersaturation) at a Pacific coastal site (Point Reyes, California). Number size distributions were calculated from the impactor data from which the mass contributions of sulfate, organic, and seasalt aerosols to CCN number concentrations were estimated. The derived and measured size distributions and the derived and measured CCN number concentrations were found to be in good agreement. Our results demonstrate that organic aerosols, depending on the meteorological conditions, may contribute a variable and often dominant fraction to the CCN concentrations.

  2. A new method for assessing the contribution of Primary Biological Atmospheric Particles to the mass concentration of the atmospheric aerosol.

    PubMed

    Perrino, Cinzia; Marcovecchio, Francesca

    2016-02-01

    Primary Biologic Atmospheric Particles (PBAPs) constitute an interesting and poorly investigated component of the atmospheric aerosol. We have developed and validated a method for evaluating the contribution of overall PBAPs to the mass concentration of atmospheric particulate matter (PM). The method is based on PM sampling on polycarbonate filters, staining of the collected particles with propidium iodide, observation at epifluorescence microscope and calculation of the bioaerosol mass using a digital image analysis software. The method has been also adapted to the observation and quantification of size-segregated aerosol samples collected by multi-stage impactors. Each step of the procedure has been individually validated. The relative repeatability of the method, calculated on 10 pairs of atmospheric PM samples collected side-by-side, was 16%. The method has been applied to real atmospheric samples collected in the vicinity of Rome, Italy. Size distribution measurements revealed that PBAPs was mainly in the coarse fraction of PM, with maxima in the range 5.6-10 μm. 24-h samples collected during different period of the year have shown that the concentration of bioaerosol was in the range 0.18-5.3 μg m(-3) (N=20), with a contribution to the organic matter in PM10 in the range 0.5-31% and to the total mass concentration of PM10 in the range 0.3-18%. The possibility to determine the concentration of total PBAPs in PM opens up interesting perspectives in terms of studying the health effects of these components and of increasing our knowledge about the composition of the organic fraction of the atmospheric aerosol. PMID:26680730

  3. Time-resolved mass concentration, composition and sources of aerosol particles in a metropolitan underground railway station

    NASA Astrophysics Data System (ADS)

    Salma, Imre; Weidinger, Tamás; Maenhaut, Willy

    Aerosol samples were collected using a stacked filter unit (SFU) for PM10-2.0 and PM2.0 size fractions on the platform of a metropolitan underground railway station in downtown Budapest. Temporal variations in the PM10 mass concentration and wind speed and direction were determined with time resolutions of 30 and 4 s using a tapered-element oscillating microbalance (TEOM) and a wind monitor, respectively. Sample analysis involved gravimetry for particulate mass, and particle-induced X-ray emission spectrometry (PIXE) for elemental composition. Diurnal variation of the PM10 mass concentration exhibited two peaks, one at approximately 07:00 h and the other at approximately 17:00 h. The mean±SD PM10 mass concentration for working hours was 155±55 μg m -3. Iron, Mn, Ni, Cu, and Cr concentrations were higher than in outdoor air by factors between 5 and 20, showing substantial enrichment compared to both the average crustal rock composition and the average outdoor aerosol composition. Iron accounted for 40% and 46% of the PM10-2.0 and PM2.0 masses, respectively, and 72% of the PM10 mass was associated with the PM10-2.0 size fraction. The aerosol composition in the metro station (in particular the abundance of the metals mentioned above) is quite different from the average outdoor downtown composition. Mechanical wear and friction of electric conducting rails and bow sliding collectors, ordinary rails and wheels, as well as resuspension, were identified as the primary sources. Possible health implications based on comparison to various limit values and to data available for other underground railways are discussed.

  4. [Study on number concentration distribution of atmospheric ultrafine particles in Hangzhou].

    PubMed

    Xie, Xiao-Fang; Sun, Zai; Fu, Zhi-Min; Yang, Wen-Jun; Lin, Jian-Zhong

    2013-02-01

    Atmospheric ultrafine particles (UFPs) were measured with fast mobility particle sizer(FMPS) in Hangzhou, during March 2011 to February 2012. The number concentration and size distribution of UFPs associated with meteorology were studied. The results showed that the number concentration of UFPs was logarithmic bi-modal distribution, and the seasonal levels presented winter > summer > spring> autumn. The highest monthly average concentration was 3.56 x 10(4) cm-3 in December and the lowest was 2.51 x 10(4) cm-3 in October. The seasonal values of count medium diameter(CMD) were spring > winter > autumn > summer. The highest monthly average CMD was 53. 51 nm in April and the lowest was 16.68 nm in June. Meteorological factors had effects on concentration of UFPs. PMID:23668106

  5. The Impact of Monthly Variation of the Pacific-North America (PNA) Teleconnection Pattern on Wintertime Surface-layer Aerosol Concentrations in the United States

    NASA Astrophysics Data System (ADS)

    Feng, J.; Liao, H.; Li, J.

    2015-12-01

    The Pacific-North America teleconnection (PNA) is the leading general circulation pattern in the troposphere over the region of North Pacific to North America during wintertime. The PNA exhibits positive (negative) phases with positive (negative) anomalies in geopotential height in the vicinity of Hawaii and over the intermountain region of North America, and negative (positive) anomalies in geopotential height over south of the Aleutian Islands and the Gulf Coast region of the United States. This study examined the impacts of monthly variation of the PNA phase on wintertime surface-layer aerosol concentrations in the United States by analyzing observations during 1999-2013 from the Air Quality System of Environmental Protection Agency (EPA-AQS) and the model results for 1986-2006 from the global three-dimensional Goddard Earth Observing System (GEOS) chemical transport model (GEOS-Chem). The composite analyses on the EPA-AQS observations over 1999-2003 showed that the average PM2.5 concentrations were higher in the PNA positive phases than in the PNA negative phases by 1.0 μg m-3 (8.6%), 2.1μg m-3 (24.1%), and 1.1 μg m-3 (10.6%) in the eastern, western, and whole of United States, respectively. Relative to the PNA negative phases, the number of exceedance days (days with the PM2.5 concentrations exceeding 35 μg m-3) in the PNA positive phases increased by 5-8 days month-1 in California and the contiguous Great Salt Lake and by 2-3 days month-1 in Iowa. The simulated geographical patterns of the differences in concentrations of PM2.5, nitrate, sulfate, ammonium, OC, and BC between the PNA positive and negative phases were similar to observations. The PNA influences surface-layer aerosol concentrations in the United States by changing meteorological variables such as temperature, precipitation, planetary boundary layer height, relative humidity, and wind speed. We found that that the PNA-induced variation in planetary boundary layer height was the most dominant

  6. Regional background aerosols over the Balearic Islands over the last 3 years: ground-based concentrations, atmospheric deposition and sources

    NASA Astrophysics Data System (ADS)

    Cerro, Jose Carlos; Pey, Jorge; Bujosa, Carles; Caballero, Sandra; Alastuey, Andres; Sicard, Michael; Artiñano, Begoña; Querol, Xavier

    2013-04-01

    In the context of the ChArMEx (The Chemistry-Aerosol Mediterranean Experiment, https://charmex.lsce.ipsl.fr) initiative, a 3-year study over a regional background environment (Can Llompart, CLP) in Mallorca has been conducted. Ground-based PM mass concentrations, gaseous pollutants and meteorological parameters were continuously registered from 2010 to 2012. Since the beginning of the campaign, PM10 daily samples for chemical determinations were obtained every 4 days, and dry and wet deposition samples were collected every week. Moreover, additional instruments (condensation particle counter, multi-angle absorption photometer, airpointer, sequential high and low volume samplers) were deployed during intensive filed campaigns in 2011 and 2012, as well as the sampling frequency was intensified. In the laboratory, PM samples were analyzed for inorganic compounds, and organic and elemental carbon following different approaches. In addition, n-alkanes, iso-alkanes, antiso-alkanes, levoglucosan, alkanoic acids and cholesterol were determined by GC-MS chromatography in a selection of 30 samples. Mean PM10, PM2.5 and PM1 concentrations in the period 2010-2012 reached 17, 11, and 8 µg/m3 respectively. Mass concentrations displayed marked seasonal trends, with much higher background levels in summer due to stagnant conditions over the western Mediterranean and increased frequency of Saharan dust events. Likewise, diverse-intensity peaks of coarse PM due to African dust inputs were observed along the year. On average, African dust in PM10 accounted for 1.0-1.5 µg/m3. Sporadic pollution events, characterized by most of the particles in the fine mode, were related to the transport of anthropogenic polluted air masses from central and eastern Europe. Wet and dry atmospheric deposition samples are being analyzed to quantify the deposition fluxes for different soluble and insoluble compounds. On average, PM10 composition is made up of organic matter (23%), mineral components (17

  7. Measurement of particle number and related pollutant concentrations in an urban area in South Brazil

    NASA Astrophysics Data System (ADS)

    Agudelo-Castañeda, D. M.; Teixeira, E. C.; Rolim, S. B. A.; Pereira, F. N.; Wiegand, F.

    2013-05-01

    The purpose of the present study was to analyze atmospheric particle number concentration at Sapucaia do Sul, in the Metropolitan Area of Porto Alegre, and associate it with the pollutants NO, NO2, and O3. Measurements were performed in two periods: August to October, in 2010 and 2011. We used the following equipment: the continuous particulate monitor (CPM), the chemiluminescent nitrogen oxide analyzer (AC32M), and the UV photometric ozone analyzer (O342M). Daily and hourly particle number concentrations in fractions PR1.0 (0.3-1.0 μm), PR2.5 (1.0-2.5 μm), and PR10 (2.5-10 μm), and concentrations of pollutants NO, NO2, NOx, and O3 were measured. These data were correlated with meteorological parameters such as wind speed, temperature, relative humidity, and solar radiation. The daily variation of OX (NO2 + O3) and its relation with NO2 were also established. The results obtained for daily particle number concentration (particles L-1) showed that the area of study had higher particle number of PR2.5 and PR1.0 size ranges, with values of 19.5 and 28.51 particles L-1, respectively. Differences in particle number concentrations in PR1 and PR2.5 size ranges were found between weekdays and weekends. The daily variation per hour of concentrations of particle number, NO, and NOx showed peaks during increased traffic flow in the morning and in the evening. NO2 showed peaks at different times, with the first peak (morning) 2 h after the peak of NO, and a second peak in the evening (19:00). This is due to the oxidation of NO and to the photolysis of NO3 formed overnight. Correlation analysis suggests that there may be a relationship between the fine and ultrafine particles and NO, probably indicating that they have similar sources, such as vehicular emissions. In addition, a possible relationship of solar radiation with fine particle number concentrations, as well as with O3 was also observed. The results, too, show an inverse relationship between particle number

  8. Emission of submicron aerosol particles in cement kilns: Total concentration and size distribution.

    PubMed

    Rotatori, Mauro; Mosca, Silvia; Guerriero, Ettore; Febo, Antonio; Giusto, Marco; Montagnoli, Mauro; Bianchini, Massimo; Ferrero, Renato

    2015-01-01

    Cement plants are responsible for particle and gaseous emissions into the atmosphere. With respect to particle emission, the greater part of is in the range from 0.05 to 5.0 µm in diameter. In the last years attention was paid to submicron particles, but there is a lack of available data on the emission from stationary sources. In this paper, concentration and size distribution of particles emitted from four cement kilns, in relationship to operational conditions (especially the use of alternative fuel to coal) of the clinker process are reported. Experimental campaigns were carried out by measuring particles concentration and size distribution at the stack of four cement plants through condensation particle counter (CPC) and scanning mobility particle sizer spectrometer (SMPS). Average total particle number concentrations were between 2000 and 4000 particles/cm³, about 8-10 times lower that those found in the corresponding surrounding areas. As for size distribution, for all the investigated plants it is stable with a unimodal distribution (120-150 nm), independent from the fuel used. PMID:25946956

  9. Long-term comparative study of columnar and surface mass concentration aerosol properties in a background environment

    NASA Astrophysics Data System (ADS)

    Bennouna, Y. S.; Cachorro, V. E.; Mateos, D.; Burgos, M. A.; Toledano, C.; Torres, B.; de Frutos, A. M.

    2016-09-01

    The relationship between columnar and surface aerosol properties is not a straightforward problem. The Aerosol Optical Depth (AOD), Ångström exponent (AE), and ground-level Particulate Matter (PMX, x = 10 or 2.5 μm) data have been studied from a climatological point of view. Despite the different meanings of AOD and PMx both are key and complementary quantities that quantify aerosol load in the atmosphere and many studies intend to find specific relationships between them. Related parameters such as AE and PM ratio (PR = PM2.5/PM10), giving information about the predominant particle size, are included in this study on the relationships between columnar and surface aerosol parameters. This study is based on long measurement records (2003-2014) obtained at two nearby background sites from the AERONET and EMEP networks in the north-central area of Spain. The climatological annual cycle of PMx shows two maxima along the year (one in late-winter/early-spring and another in summer), but this cycle is not followed by the AOD which shows only a summer maximum and a nearly bell shape. However, the annual means of both data sets show strong correlation (R = 0.89) and similar decreasing trends of 40% (PM10) and 38% (AOD) for the 12-year record. PM10 and AOD daily data are moderately correlated (R = 0.58), whereas correlation increases for monthly (R = 0.74) and yearly (R = 0.89) means. Scatter plots of AE vs. AOD and PR vs. PM10 have been used to characterize aerosols over the region. The PR vs. AE scatterplot of daily data shows no correlation due to the prevalence of intermediate-sized particles. As day-to-day correlation is low (especially for high turbidity events), a binned analysis was also carried out to establish consistent relationships between columnar and surface quantities, which is considered to be an appropriate approach for environmental and climate studies. In this way the link between surface concentrations and columnar remote sensing data is shown to

  10. Seasonal evolution of anionic, cationic and non-ionic surfactant concentrations in coastal aerosols from Askö, Sweden

    NASA Astrophysics Data System (ADS)

    Gérard, Violaine; Nozière, Barbara; Baduel, Christine

    2015-04-01

    Surfactants present in atmospheric aerosols are expected to enhance the activation into cloud droplets by acting on one of the two key parameters of the Köhler equation: the surface tension, σ. But because the magnitude of this effect and its regional and temporal variability are still highly uncertain [1,2], various approaches have been developed to evidence it directly in the atmosphere. This work presents the analysis of surfactants present in PM2.5 aerosol fractions collected at the coastal site of Askö, Sweden (58° 49.5' N, 17° 39' E) from July to October 2010. The total surfactant fraction was extracted from the samples using an improved double extraction technique. Surface tension measurements performed with the pendant drop technique [3] indicated the presence of very strong surfactants (σ ~ 30 - 35 mN/m) in these aerosols. In addition, these extractions were combined with colorimetric methods to determine the anionic, cationic and non-ionic surfactant concentrations [4,5], and provided for the first time interference-free surfactant concentrations in atmospheric aerosols. At this site, the total surfactant concentration in the PM2.5 samples varied between 7 to 150 mM and was dominated by anionic and non-ionic ones. The absolute surface tension curves obtained for total surfactant fraction displayed Critical Micelle Concentrations (CMC) in the range 50 - 400 uM, strongly suggesting a biological origin for the surfactants. The seasonal evolution of these concentrations and their relationships with environmental or meteorological parameters at the site will be discussed. [1] Ekström, S., Nozière, B. et al., Biogeosciences, 2010, 7, 387 [2] Baduel, C., Nozière, B., Jaffrezo, J.-L., Atmos. Environ., 2012, 47, 413 [3] Nozière, B., Baduel, C., Jaffrezo, J.-L., Nat. Commun., 2014, 5, 1 [4] Latif, M. T.; Brimblecombe, P. Environ. Sci. Technol., 2004, 38, 6501 [5] Pacheco e Silva et al., Method to measure surfactant in fluid, 2013, US 2013/0337568 A1

  11. Metal concentration and bioaccessibility in different particle sizes of dust and aerosols to refine metal exposure assessment.

    PubMed

    Goix, Sylvaine; Uzu, Gaëlle; Oliva, Priscia; Barraza, Fiorella; Calas, Aude; Castet, Sylvie; Point, David; Masbou, Jeremy; Duprey, Jean-Louis; Huayta, Carlos; Chincheros, Jaime; Gardon, Jacques

    2016-11-01

    Refined exposure assessments were realized for children, 7-9yrs, in the mining/smelting city of Oruro, Bolivia. Aerosols (PM>2.5, PM1-2.5, PM0.4-1 and PM0.5) and dust (separated in different particle size fractions: 2000-200μm, 200-50μm, 50-20μm, 20-2μm and <2μm) were sampled on football fields highly frequented by children in both the mining and smelting areas. Trace element concentrations (Ag, As, Cd, Cu, Pb, Sb, Sn and Zn) in each size fraction of dust and aerosols, lung bioaccessibility of metals in aerosols, and gastric bioaccessibility of metals in dust were measured. Exposure was assessed considering actual external exposure (i.e. exposure pathways: metals inhaled and ingested) and simulated internal exposure (i.e., complex estimation using gastric and lung bioaccessibility, deposition and clearance of particles in lungs). Significant differences between external and simulated internal exposure were attributed to dissemblances in gastric and lung bioaccessibilities, as well as metal distribution within particle size range, revealing the importance of both parameters in exposure assessment. PMID:27344256

  12. Concentrations of iodine isotopes ((129)I and (127)I) and their isotopic ratios in aerosol samples from Northern Germany.

    PubMed

    Daraoui, A; Riebe, B; Walther, C; Wershofen, H; Schlosser, C; Vockenhuber, C; Synal, H-A

    2016-04-01

    New data about (129)I, (127)I concentrations and their isotopic ratios in aerosol samples from the trace survey station of the Physikalisch-Technische Bundesanstalt (PTB) in Braunschweig, Northern Germany, are presented and discussed in this paper. The investigated samples were collected on a weekly basis during the years 2011 to 2013. Iodine was extracted from aerosol filters using a strong basic solution and was separated from the matrix elements with chloroform and was analysed by accelerator mass spectrometry (AMS) for (129)I and by inductively coupled plasma mass spectrometry (ICP-MS) for (127)I. The concentrations of (127)I and (129)I in aerosol filters ranged from 0.31 to 3.71 ng m(-3) and from 0.06 to 0.75 fg m(-3), respectively. The results of (129)I/(127)I isotopic ratios were in the order 10(-8) to 10(-7). The (129)I originated directly from gaseous emissions and indirectly from liquid emissions (via sea spray) from the reprocessing plants in Sellafield and La Hague. In comparison with the results of (131)I after the Fukushima accident, no contribution of (129)I from this accident was detectable in Central Europe due to the high background originating from the (129)I releases of the European reprocessing plants. (129)I atmospheric activity concentrations were compared with those of an anthropogenic radionuclide ((85)Kr). We did not find any correlation between (129)I and (85)Kr, both having nuclear reprocessing plant as the main source. PMID:26867099

  13. Thermal convection at low Rayleigh number from concentrated sources in porous media

    SciTech Connect

    Hickox, C. E.

    1980-01-01

    A simple mathematical theory is proposed for the analysis of natural convective motion, at low Rayleigh number, from a concentrated source of heat in a fluid-saturated porous medium. The theory consists of retaining only the leading terms of series expansions of the dependent variables in terms of the Rayleigh number, is thus linear, and is valid only in the limit of small Rayleigh number. Based on fundamental results for a variety of isolated sources, superposition is used to provide solutions for situations of practical interest. Special emphasis is given to the analysis of sub-seabed disposal of nuclear waste. 8 figures.

  14. Regional Comparisons of Satellite (AVHRR) and Space Shuttle (MAPS) Derived Estimates of CO and Aerosol Concentrations

    NASA Technical Reports Server (NTRS)

    Vulcan, D. V.; Christopher, S. A.; Welch, R. M.; Connors, V. S.

    1996-01-01

    Biomass burning is considered to be a major source of trace gas species and aerosol particles which play a vital role in tropospheric chemistry and climate. Anthropogenic biomass burning has largely expanded in the last 15 years, due to increased deforestation practices in the Amazon Basin, as well as to clear land for shifting cultivation in South America, southern Asia, and Africa. Biomass burning produces large amounts of carbon dioxide, carbon monoxide (CO), water, hydrocarbons, nitrous oxides, and smoke particles.

  15. Diurnal and elevational variations in ozone and aerosol concentrations in New Hampshire`s Class-I Airsheds

    SciTech Connect

    Hill, L.B.; Allen, G.A.

    1994-12-31

    Ozone and fine mass aerosol concentrations on New Hampshire`s Mount Washington, situated adjacent to both the Presidential/Dry River and Great Gulf Wilderness Class-I Airsheds, exhibit distinct diurnal and elevational patterns. These patterns are attributed to regional pollutant transport dynamics, nocturnal atmospheric stratification, mountain meteorological phenomena and scavenging. A well-defined planetary boundary layer (PBL) forms at about 1 km elevation at night as demonstrated by nocturnal ozone monitoring along the Mount Washington Auto Road. The PBL provides an effective elevational barrier at night, isolating the valleys from the regionally transported air pollutants present above the mixing layer. During the daytime, the PBL breaks up due to convective processes and katabatic winds resulting from solar heating in the valley. This process creates a diurnal mixing cycle with ozone maxima recorded near mid-day in the adjacent valley. In contrast, fine mass concentrations are higher at the valley site, attributed to local source inputs, and the lack of strong nocturnal scavenging processes, compared with ozone. How aerosol concentrations are related to the PBL and how they are affected by diurnal mixing remains unclear largely due to current sampling methods. Exposure to ozone is generally greater above the treeline in the two airsheds.

  16. AGLITE: a multiwavelength lidar for aerosol size distributions, flux, and concentrations

    NASA Astrophysics Data System (ADS)

    Wilkerson, Thomas D.; Zavyalov, Vladimir V.; Bingham, Gail E.; Swasey, Jason A.; Hancock, Jed J.; Crowther, Blake G.; Cornelsen, Scott S.; Marchant, Christian; Cutts, James N.; Huish, David C.; Earl, Curtis L.; Andersen, Jan M.; Cox, McLain L.

    2006-05-01

    We report on the design, construction and operation of a new multiwavelength lidar developed for the Agricultural Research Service of the United States Department of Agriculture and its program on particle emissions from animal production facilities. The lidar incorporates a laser emitting simultaneous, pulsed Nd laser radiation at 355, 532 and 1064 nm at a PRF of 10 kHz. Lidar backscatter and extinction data are modeled to extract the aerosol information. All-reflective optics combined with dichroic and interferometric filters permit all the wavelength channels to be measured simultaneously, day or night, using photon counting by PMTs, an APD, and high speed scaling. The lidar is housed in a transportable trailer for all-weather operation at any accessible site. The laser beams are directed in both azimuth and elevation to targets of interest. We describe application of the lidar in a multidisciplinary atmospheric study at a swine production farm in Iowa. Aerosol plumes emitted from the hog barns were prominent phenomena, and their variations with temperature, turbulence, stability and feed cycle were studied, using arrays of particle samplers and turbulence detectors. Other lidar measurements focused on air motion as seen by long duration scans of the farm region. Successful operation of this lidar confirms the value of multiwavelength, eye-safe lidars for agricultural aerosol measurements.

  17. Recent Alterations of Aerosol Concentration, Mercury Distribution And Organic Matter Deposition In The Arctic

    NASA Astrophysics Data System (ADS)

    Pempkowiak, Janusz; Zieliński, Tymon; Petelski, Tomasz; Zaborska, Agata; Bełdowski, Jacek

    2011-01-01

    Material fluxes in the Arctic and Antarctic have been, in several respects, strongly affected recently. For example, atmospheric turbidity conditions are frequently subject to strong changes due to haze and dust transport episodes, which can cause considerable perturbations in the radiation balance of the atmosphere beyond regional scale. This, directly or indirectly, contributes to the increased mercury deposition and organic matter fluxes to sediments. The results show that local emissions are not always the most important factors influencing the composition of aerosol in the atmosphere of the west Spitsbergen region. The direct radiative impact of polar aerosols on the surface and at the top of the atmosphere (TOA) need to be studied more closely through both theoretical studies on the aerosol radiative properties and measurements of the surface reflectance characteristics. Mercury dissolved/solid partitioning, both in the unconsolidated, fluffy layer of suspended matter covering the sediments, and the uppermost sediment layer, indicate that the influence of the athmospheric mercury deposition event (AMDE) can prolong well into summer (July/August), and can provide a pathway to the food chain for mercury contained in sediments. Since terrigenous supplies of organic carbon to the Barents Sea are minor (˜5%) compared to the marine supply, modern sediment deposits in this region sequester on average 6.0 g/m2year organic carbon, or 5.8% of the annual integrated pelagic primary production. This burial fraction exceeds, by a factor of 3, the burial fraction derived for the Holocene.

  18. Recent Alterations of Aerosol Concentration, Mercury Distribution and Organic Matter Deposition in the Arctic

    NASA Astrophysics Data System (ADS)

    Pempkowiak, Janusz; Zieliński, Tymon; Petelski, Tomasz; Bełdowski, Agata Zaborska Jacek

    2011-01-01

    Material fluxes in the Arctic and Antarctic have been, in several respects, strongly affected recently. For example, atmospheric turbidity conditions are frequently subject to strong changes due to haze and dust transport episodes, which can cause considerable perturbations in the radiation balance of the atmosphere beyond regional scale. This, directly or indirectly, contributes to the increased mercury deposition and organic matter fluxes to sediments. The results show that local emissions are not always the most important factors influencing the composition of aerosol in the atmosphere of the west Spitsbergen region. The direct radiative impact of polar aerosols on the surface and at the top of the atmosphere (TOA) need to be studied more closely through both theoretical studies on the aerosol radiative properties and measurements of the surface reflectance characteristics. Mercury dissolved/solid partitioning, both in the unconsolidated, fluffy layer of suspended matter covering the sediments, and the uppermost sediment layer, indicate that the influence of the athmospheric mercury deposition event (AMDE) can prolong well into summer (July/August), and can provide a pathway to the food chain for mercury contained in sediments. Since terrigenous supplies of organic carbon to the Barents Sea are minor (~5%) compared to the marine supply, modern sediment deposits in this region sequester on average 6.0 g/m2year organic carbon, or 5.8% of the annual integrated pelagic primary production. This burial fraction exceeds, by a factor of 3, the burial fraction derived for the Holocene.

  19. The Effects of Vegetation Barriers on Near-road Ultrafine Particle Number and Carbon Monoxide Concentrations

    EPA Science Inventory

    Numerous studies have shown that people living in near-roadway communities (within 100 m of the road) are exposed to high ultrafine particle (UFP) number concentrations, which may be associated with adverse health effects. Vegetation barriers have been shown to affect pollutant t...

  20. Vehicle and driving characteristics that influence in-cabin particle number concentrations.

    PubMed

    Hudda, Neelakshi; Kostenidou, Evangelia; Sioutas, Constantinos; Delfino, Ralph J; Fruin, Scott A

    2011-10-15

    In-transit microenvironments experience elevated levels of vehicle-related pollutants such as ultrafine particles. However, in-vehicle particle number concentrations are frequently lower than on-road concentrations due to particle losses inside vehicles. Particle concentration reduction occurs due to a complicated interplay between a vehicle's air-exchange rate (AER), which determines particle influx rate, and particle losses due to surfaces and the in-cabin air filter. Accurate determination of inside-to-outside particle concentration ratios is best made under realistic aerodynamic and AER conditions because these ratios and AER are determined by vehicle speed and ventilation preference, in addition to vehicle characteristics such as age. In this study, 6 vehicles were tested at 76 combinations of driving speeds, ventilation conditions (i.e., outside air or recirculation), and fan settings. Under recirculation conditions, particle number attenuation (number reduction for 10-1000 nm particles) averaged 0.83 ± 0.13 and was strongly negatively correlated with increasing AER, which in turn depended on speed and the age of the vehicle. Under outside air conditions, attenuation averaged 0.33 ± 0.10 and primarily decreased at higher fan settings that increased AER. In general, in-cabin particle number reductions did not vary strongly with particle size, and cabin filters exhibited low removal efficiencies. PMID:21928803

  1. Spatio-temporal covariation of urban particle number concentration and ambient noise

    NASA Astrophysics Data System (ADS)

    Weber, Stephan

    Mobile measurements of ambient noise and particle number concentrations were carried out within an urban residential area in Essen, Germany, during summer 2008. A busy major road with a traffic intensity of about 44,000 vehicles per day was situated within the study area. The spatio-temporal distribution of noise and particles was closely coupled to road traffic on the major road. Total particle number concentrations in proximity to the main road were on average between 25,000 cm -3 and 35,000 cm -3 while sound levels reached 70-78 dB(A). These estimates were more than double-fold (factor 2.4) in comparison to the urban residential background. At a 50 m distance off the road particle number concentrations were decaying to about 50% of the initial value. The measurements were characterised by close spatial correlation between total particle number concentration and ambient noise with correlation coefficients of up to r = 0.74. However, during one measurement day coupling between both quantities was weak due to higher turbulent mixing within the canopy layer and a change in ambient wind directions. Enhanced dilution of particle emission from road traffic by turbulent mixing and 'decoupling' from the influence of road traffic are believed to be responsible.

  2. DNA copy number concentration measured by digital and droplet digital quantitative PCR using certified reference materials.

    PubMed

    Corbisier, Philippe; Pinheiro, Leonardo; Mazoua, Stéphane; Kortekaas, Anne-Marie; Chung, Pui Yan Jenny; Gerganova, Tsvetelina; Roebben, Gert; Emons, Hendrik; Emslie, Kerry

    2015-03-01

    The value assignment for properties of six certified reference materials (ERM-AD623a-f), each containing a plasmid DNA solution ranging from 1 million to 10 copies per μL, by using digital PCR (dPCR) with the BioMark™ HD System (Fluidigm) has been verified by applying droplet digital PCR (ddPCR) using the QX100 system (Bio-Rad). One of the critical factors in the measurement of copy number concentrations by digital PCR is the partition volume. Therefore, we determined the average droplet volume by optical microscopy, revealing an average droplet volume that is 8 % smaller than the droplet volume used as the defined parameter in the QuantaSoft software version 1.3.2.0 (Bio-Rad) to calculate the copy number concentration. This observation explains why copy number concentrations estimated with ddPCR and using an average droplet volume predefined in the QuantaSoft software were systematically lower than those measured by dPCR, creating a significant bias between the values obtained by these two techniques. The difference was not significant anymore when the measured droplet volume of 0.834 nL was used to estimate copy number concentrations. A new version of QuantaSoft software (version 1.6.6.0320), which has since been released with Bio-Rad's new QX200 systems and QX100 upgrades, uses a droplet volume of 0.85 nL as a defined parameter to calculate copy number concentration. PMID:25600685

  3. Size distribution and number concentration of particles at the stack of a municipal waste incinerator.

    PubMed

    Buonanno, G; Ficco, G; Stabile, L

    2009-02-01

    A large number of particles and gaseous products are generated by waste combustion processes. Of particular importance are the ultrafine particles (less than 0.1 microm in aerodynamic diameter) that are emitted in large quantities from all the combustion sources. Recent findings of toxicological and epidemiological studies indicate that fine and ultrafine particles could represent health and environmental risks. Quantifying particulate emissions from combustion sources is important: (i) to examine the source status in compliance with regulations; (ii) to create inventories of such emissions at local, regional and national levels, for developing appropriate management and control strategies in relation to air quality; (iii) to predict ambient air quality in the areas involved at the source and (iv) to perform source apportionment and exposure assessment for the human populations and/or ecological systems involved. In order to control and mitigate the particles in the view of health and environmental risk reduction, a good understanding of the relative and absolute contribution from the emission sources to the airborne concentrations is necessary. For these purposes, the concentration and size distribution of particles in terms of mass and number in a waste gas of a municipal waste incineration plant were measured in the stack gas. The mass concentrations obtained are well below the imposed daily threshold value for both incineration lines and the mass size distribution is on average very stable. The total number concentrations are between 1 x 10(5) and 2 x 10(5)particles/cm(3) and are on average relatively stable from one test to another. The measured values and the comparison with other point sources show a very low total number concentration of particles at the stack gas, revealing the importance of the flue gas treatment also for ultrafine particles. Also in respect to linear sources (high and light duty vehicles), the comparison shows a negligible emission in

  4. Modeling particle number concentrations along Interstate 10 in El Paso, Texas

    PubMed Central

    Olvera, Hector A.; Jimenez, Omar; Provencio-Vasquez, Elias

    2014-01-01

    Annual average daily particle number concentrations around a highway were estimated with an atmospheric dispersion model and a land use regression model. The dispersion model was used to estimate particle concentrations along Interstate 10 at 98 locations within El Paso, Texas. This model employed annual averaged wind speed and annual average daily traffic counts as inputs. A land use regression model with vehicle kilometers traveled as the predictor variable was used to estimate local background concentrations away from the highway to adjust the near-highway concentration estimates. Estimated particle number concentrations ranged between 9.8 × 103 particles/cc and 1.3 × 105 particles/cc, and averaged 2.5 × 104 particles/cc (SE 421.0). Estimates were compared against values measured at seven sites located along I10 throughout the region. The average fractional error was 6% and ranged between -1% and -13% across sites. The largest bias of -13% was observed at a semi-rural site where traffic was lowest. The average bias amongst urban sites was 5%. The accuracy of the estimates depended primarily on the emission factor and the adjustment to local background conditions. An emission factor of 1.63 × 1014 particles/veh-km was based on a value proposed in the literature and adjusted with local measurements. The integration of the two modeling techniques ensured that the particle number concentrations estimates captured the impact of traffic along both the highway and arterial roadways. The performance and economical aspects of the two modeling techniques used in this study shows that producing particle concentration surfaces along major roadways would be feasible in urban regions where traffic and meteorological data are readily available. PMID:25313294

  5. Modeling particle number concentrations along Interstate 10 in El Paso, Texas.

    PubMed

    Olvera, Hector A; Jimenez, Omar; Provencio-Vasquez, Elias

    2014-12-01

    Annual average daily particle number concentrations around a highway were estimated with an atmospheric dispersion model and a land use regression model. The dispersion model was used to estimate particle concentrations along Interstate 10 at 98 locations within El Paso, Texas. This model employed annual averaged wind speed and annual average daily traffic counts as inputs. A land use regression model with vehicle kilometers traveled as the predictor variable was used to estimate local background concentrations away from the highway to adjust the near-highway concentration estimates. Estimated particle number concentrations ranged between 9.8 × 10(3) particles/cc and 1.3 × 10(5) particles/cc, and averaged 2.5 × 10(4) particles/cc (SE 421.0). Estimates were compared against values measured at seven sites located along I10 throughout the region. The average fractional error was 6% and ranged between -1% and -13% across sites. The largest bias of -13% was observed at a semi-rural site where traffic was lowest. The average bias amongst urban sites was 5%. The accuracy of the estimates depended primarily on the emission factor and the adjustment to local background conditions. An emission factor of 1.63 × 10(14) particles/veh-km was based on a value proposed in the literature and adjusted with local measurements. The integration of the two modeling techniques ensured that the particle number concentrations estimates captured the impact of traffic along both the highway and arterial roadways. The performance and economical aspects of the two modeling techniques used in this study shows that producing particle concentration surfaces along major roadways would be feasible in urban regions where traffic and meteorological data are readily available. PMID:25313294

  6. Modeling particle number concentrations along Interstate 10 in El Paso, Texas

    NASA Astrophysics Data System (ADS)

    Olvera, Hector A.; Jimenez, Omar; Provencio-Vasquez, Elias

    2014-12-01

    Annual average daily particle number concentrations around a highway were estimated with an atmospheric dispersion model and a land use regression model. The dispersion model was used to estimate particle concentrations along Interstate 10 at 98 locations within El Paso, Texas. This model employed annual averaged wind speed and annual average daily traffic counts as inputs. A land use regression model with vehicle kilometers traveled as the predictor variable was used to estimate local background concentrations away from the highway to adjust the near-highway concentration estimates. Estimated particle number concentrations ranged between 9.8 × 103 particles/cc and 1.3 × 105 particles/cc, and averaged 2.5 × 104 particles/cc (SE 421.0). Estimates were compared against values measured at seven sites located along I10 throughout the region. The average fractional error was 6% and ranged between -1% and -13% across sites. The largest bias of -13% was observed at a semi-rural site where traffic was lowest. The average bias amongst urban sites was 5%. The accuracy of the estimates depended primarily on the emission factor and the adjustment to local background conditions. An emission factor of 1.63 × 1014 particles/veh-km was based on a value proposed in the literature and adjusted with local measurements. The integration of the two modeling techniques ensured that the particle number concentrations estimates captured the impact of traffic along both the highway and arterial roadways. The performance and economical aspects of the two modeling techniques used in this study shows that producing particle concentration surfaces along major roadways would be feasible in urban regions where traffic and meteorological data are readily available.

  7. MODELING AND EXPERIMENTAL EVALUATION OF AN AEROSOL GENERATOR FOR VERY HIGH NUMBER CURRENTS BASED ON A FREE TURBULENT JET. (R827354C008)

    EPA Science Inventory

    In this paper we report on theoretical and experimental work on aerosol formation in a free turbulent jet. A hot DEHS vapor issues through a circular nozzle into slowly moving cold air. Vapor concentration and temperatures are such that particles are formed via homogeneous nuc...

  8. Indoor and outdoor PM mass and number concentrations at schools in the Athens area.

    PubMed

    Diapouli, E; Chaloulakou, A; Mihalopoulos, N; Spyrellis, N

    2008-01-01

    Simultaneous indoor and outdoor PM10 and PM2.5 concentration measurements were conducted in seven primary schools in the Athens area. Both gravimetric samplers and continuous monitors were used. Filters were subsequently analyzed for anion species. Moreover ultrafine particles number concentration was monitored continuously indoors and outdoors. Mean 8-hr PM10 concentration was measured equal to 229 +/- 182 microg/m3 indoors and 166 +/- 133 microg/m3 outdoors. The respective PM2.5 concentrations were 82 +/- 56 microg/m3 indoors and 56 +/- 26 microg/m3 outdoors. Ultrafine particles 8-h mean number concentration was measured equal to 24,000 +/- 17,900 particles/cm3 indoors and 32,000 +/- 14,200 particles/cm3 outdoors. PM10 outdoor concentrations exhibited a greater spatial variability than the corresponding PM2.5 ones. I/O ratios were close or above 1.00 for PM10 and PM2.5 and smaller than 1.00 for ultrafine particles. Very high I/O ratios were observed when intense activities took place. The initial results of the chemical analysis showed that SO4(-2) accounts for the 6.6 +/- 3.5% of the PM10 and NO3(1) for the 3.1 +/- 1.4%.The corresponding results for PM2.5 are 12.0 +/- 7.7% for SO4(-2) and 3.1 +/- 1.9% for NO3-. PM2.5 SO4(-2) indoor concentrations were highly correlated with outdoor ones and the regression line had the largest slope and a very low intercept, indicative of no indoor sources of fine particulate SO4(-2). The results of the statistical analysis of indoor and outdoor concentration data support the use of SO4(-2) as a proper surrogate for indoor PM of outdoor origin. PMID:17458512

  9. Non-sea-salt sulfate, methanesulfonate, and nitrate aerosol concentrations and size distributions at Cape Grim, Tasmania

    NASA Astrophysics Data System (ADS)

    Andreae, Meinrat O.; Elbert, Wolfgang; Cai, Yong; Andreae, Tracey W.; Gras, John

    1999-09-01

    We collected weekly aerosol samples using high-volume impactors over a period of 20 months (1988-1990) at the Cape Grim baseline station on the northwestern coast of Tasmania, Australia. The samples were analyzed for soluble ionic constituents, including sulfate, methanesulfonate (MS-), ammonium, nitrate, and the major sea-salt ions. The sea-salt component showed only a slight seasonal variation, whereas the non-sea-salt (nss) ions all had pronounced summer maxima. Significant interannual variability was seen between the nss ion concentrations measured during the two summers investigated. Nss sulfate and MS- were present both in the fine and coarse aerosol fractions, in the latter presumably associated with sea-salt particles. During the winter period, there was more nss sulfate in the coarse fraction than in the fine fraction. These observations are consistent with an important role of liquid-phase oxidation in haze and cloud droplets for the production of nss sulfate aerosol. The seasonal behavior of the sulfur and nitrogen species at Cape Grim and their mutual correlations suggest that DMS oxidation is the dominant sulfur source during summer, while nonbiogenic sulfur sources make significant contributions to nss sulfate outside of this season. Correlations of CN and CCN concentrations with nss sulfate, MS-, and wind speed suggest that DMS oxidation and, to a lesser extent, seaspray formation contributes to CN and CCN populations. The contrast between the weak seasonality of the sea-salt component and the pronounced seasonal behavior in both sulfur species and CCN supports the central role of biogenic DMS emissions as precursors of CCN in this region, at least in the biologically productive season.

  10. Source and Health Implication of Diurnal Atmospheric PM Mass and Number Concentrations

    NASA Astrophysics Data System (ADS)

    Li, W.; Olvera, H. A.; Garcia, J. H.; Pingitore, N. E.

    2007-12-01

    Exposure to atmospheric PM has been known to be associated with adverse health effects, decreased heart-rate variability, and respiratory and cardiopulmonary related morbidity and mortality. New evidence suggests that physical characteristics (mass, size, number, surface area, and morphology) of particles are strongly associated with mortality and morbidity through acute exposure. In particular, as reported in the literature, fine or ultrafine particles are more toxic than coarse particles on an equivalent mass basis while particles of less than 30 nm or greater than 2.5 um in diameter deposit more effectively (approximately 80 percent) in lung versus approximately 18 percent for particles in the range of 100 nm and 1 um. In addition, positive association has been observed between day to day variation in PM2.5 and hospital admissions, mortality and particle surface area, or particle number concentration and oxidative stress-induced DNA damage. This presentation shows the results of a study characterizing the physical properties of PM in El Paso, Texas. Diurnal PM mass concentration peaks previously observed at several other cities along the U.S.-Mexico border and elsewhere in the world were observed in El Paso. The hourly PM particle count varied from less than 10,000 particles/cm3 to greater than 80,000 particles/cm3 during the diurnal PM mass peaks. The total number of PM particles peaked in the morning and in the evening while the mode of the particle size changed from 20 nm to 50 nm, indicating different PM sources may be responsible for the mass and number concentrations and agglomeration of particles in the atmosphere during the day may possibly plays a role. A multivariate regression analysis was performed to correlate the PM mass and number concentrations to environmental variables. Real- time wind statistics were used in conjunction with traffic data at a nearby highway for identifying sources of the PM mass and number concentration peaks. Evaluation of

  11. Emissions from an International Airport Increase Particle Number Concentrations 4-fold at 10 km Downwind

    PubMed Central

    2014-01-01

    We measured the spatial pattern of particle number (PN) concentrations downwind from the Los Angeles International Airport (LAX) with an instrumented vehicle that enabled us to cover larger areas than allowed by traditional stationary measurements. LAX emissions adversely impacted air quality much farther than reported in previous airport studies. We measured at least a 2-fold increase in PN concentrations over unimpacted baseline PN concentrations during most hours of the day in an area of about 60 km2 that extended to 16 km (10 miles) downwind and a 4- to 5-fold increase to 8–10 km (5–6 miles) downwind. Locations of maximum PN concentrations were aligned to eastern, downwind jet trajectories during prevailing westerly winds and to 8 km downwind concentrations exceeded 75 000 particles/cm3, more than the average freeway PN concentration in Los Angeles. During infrequent northerly winds, the impact area remained large but shifted to south of the airport. The freeway length that would cause an impact equivalent to that measured in this study (i.e., PN concentration increases weighted by the area impacted) was estimated to be 280–790 km. The total freeway length in Los Angeles is 1500 km. These results suggest that airport emissions are a major source of PN in Los Angeles that are of the same general magnitude as the entire urban freeway network. They also indicate that the air quality impact areas of major airports may have been seriously underestimated. PMID:24871496

  12. Emissions from an international airport increase particle number concentrations 4-fold at 10 km downwind.

    PubMed

    Hudda, Neelakshi; Gould, Tim; Hartin, Kris; Larson, Timothy V; Fruin, Scott A

    2014-06-17

    We measured the spatial pattern of particle number (PN) concentrations downwind from the Los Angeles International Airport (LAX) with an instrumented vehicle that enabled us to cover larger areas than allowed by traditional stationary measurements. LAX emissions adversely impacted air quality much farther than reported in previous airport studies. We measured at least a 2-fold increase in PN concentrations over unimpacted baseline PN concentrations during most hours of the day in an area of about 60 km(2) that extended to 16 km (10 miles) downwind and a 4- to 5-fold increase to 8-10 km (5-6 miles) downwind. Locations of maximum PN concentrations were aligned to eastern, downwind jet trajectories during prevailing westerly winds and to 8 km downwind concentrations exceeded 75 000 particles/cm(3), more than the average freeway PN concentration in Los Angeles. During infrequent northerly winds, the impact area remained large but shifted to south of the airport. The freeway length that would cause an impact equivalent to that measured in this study (i.e., PN concentration increases weighted by the area impacted) was estimated to be 280-790 km. The total freeway length in Los Angeles is 1500 km. These results suggest that airport emissions are a major source of PN in Los Angeles that are of the same general magnitude as the entire urban freeway network. They also indicate that the air quality impact areas of major airports may have been seriously underestimated. PMID:24871496

  13. Contribution from indoor sources to particle number and mass concentrations in residential houses

    NASA Astrophysics Data System (ADS)

    He, Congrong; Morawska, Lidia; Hitchins, Jane; Gilbert, Dale

    As part of a large study investigating indoor air in residential houses in Brisbane, Australia, the purpose of this work was to quantify emission characteristics of indoor particle sources in 15 houses. Submicrometer particle number and approximation of PM 2.5 concentrations were measured simultaneously for more than 48 h in the kitchen of all the houses by using a condensation particle counter (CPC) and a photometer (DustTrak), respectively. In addition, characterizations of particles resulting from cooking conducted in an identical way in all the houses were measured by using a scanning mobility particle sizer (SMPS), an aerodynamic particle sizer (APS) and a DustTrak. All the events of elevated particle concentrations were linked to indoor activities using house occupants diary entries, and catalogued into 21 different types of indoor activities. This enabled quantification of the effect of indoor sources on indoor particle concentrations as well as quantification of emission rates from the sources. For example, the study found that frying, grilling, stove use, toasting, cooking pizza, cooking, candle vaporizing eucalyptus oil and fan heater use, could elevate the indoor submicrometer particle number concentration levels by more than five times, while PM 2.5 concentrations could be up to 3, 30 and 90 times higher than the background levels during smoking, frying and grilling, respectively.

  14. A Nanometer Aerosol Size Analyzer (nASA) for Rapid Measurement of High-Concentration Size Distributions

    NASA Technical Reports Server (NTRS)

    Han, Hee-Siew; Chen, Da-Ren; Pui, David Y. H.; Anderson, Bruce E.

    2001-01-01

    We have developed a fast-response Nanometer Aerosol Size Analyzer (nASA) that is capable of scanning 30 size channels between 3 and 100 nm in a total time of 3 seconds. The analyzer includes a bipolar charger (P0210), an extended-length Nanometer Differential Mobility Analyzer (Nano-DMA), and an electrometer (TSI 3068). This combination of components provides particle size spectra at a scan rate of 0.1 second per channel free of uncertainties caused by response-time-induced smearing. The nASA thus offers a fast response for aerosol size distribution measurements in high-concentration conditions and also eliminates the need for applying a de-smearing algorithm to resulting data. In addition, because of its thermodynamically stable means of particle detection, the nASA is useful for applications requiring measurements over a broad range of sample pressures and temperatures. Indeed, experimental transfer functions determined for the extended-length Nano-DMA using the Tandem Differential Mobility Analyzer (TDMA) technique indicate the nASA provides good size resolution at pressures as low as 200 Torr. Also, as was demonstrated in tests to characterize the soot emissions from the J85-GE engine of a T38 aircraft, the broad dynamic concentration range of the nASA makes it particularly suitable for studies of combustion or particle formation processes. Further details of the nASA performance as well as results from calibrations, laboratory tests and field applications are presented.

  15. ANALYSIS OF RESPIRATORY DEPOSITION OF INHALED PARTICLES FOR DIFFERENT DOSE METRICS: COMPARISON OF NUMBER, SURFACE AREA AND MASS DOSE OF TYPICAL AMBIENT BI-MODAL AEROSOLS

    EPA Science Inventory

    ANALYSIS OF RESPIRATORY DEPOSITION OF INHALED PARTICLES FOR DIFFERENT DOSE METRICS: COMPARISON OF NUMBER, SURFACE AREA AND MASS DOSE OF TYPICAL AMBIENT BI-MODAL AEROSOLS.
    Chong S. Kim, SC. Hu*, PA Jaques*, US EPA, National Health and Environmental Effects Research Laboratory, ...

  16. Airborne DOAS measurements in Arctic: vertical distributions of aerosol extinction coefficient and NO2 concentration

    NASA Astrophysics Data System (ADS)

    Merlaud, A.; van Roozendael, M.; Theys, N.; Fayt, C.; Hermans, C.; Quennehen, B.; Schwarzenboeck, A.; Ancellet, G.; Pommier, M.; Pelon, J.; Burkhart, J.; Stohl, A.; de Mazière, M.

    2011-05-01

    We report airborne differential optical absorption spectroscopy (DOAS) measurements of aerosol extinction and NO2 tropospheric profiles performed off the North coast of Norway in April 2008. The DOAS instrument was installed on the Safire ATR-42 aircraft during the POLARCAT-France spring campaign and recorded scattered light spectra in near-limb geometry using a scanning telescope. We use O4 slant column measurements to derive the aerosol extinction at 360 nm. Regularization is based on the maximum a posteriori solution, for which we compare a linear and a logarithmic approach. The latter inherently constrains the solution to positive values and yields aerosol extinction profiles more consistent with independently measured size distributions. Two soundings are presented, performed on 8 April 2008 above 71° N, 22° E and on 9 April 2008 above 70° N, 17.8° E. The first profile shows aerosol extinction and NO2 in the marine boundary layer with respective values of 0.04±0.005 km-1 and 1.9±0.3 × 109 molec cm-3. A second extinction layer of 0.01±0.003 km-1 is found at 4 km altitude. During the second sounding, clouds prevented us to retrieve profile parts under 3 km altitude but a layer with enhanced extinction (0.025±0.005 km-1) and NO2 (1.95±0.2 × 109 molec cm-3) is clearly detected at 4 km altitude. From CO and ozone in-situ measurements complemented by back-trajectories, we interpret the measurements in the free troposphere as, for the first sounding, a mix between stratospheric and polluted air from Northern Europe and for the second sounding, polluted air from Central Europe containing NO2. Considering the boundary layer measurements of the first flight, modeled source regions indicate closer sources, especially the Kola Peninsula smelters, which can explain the NO2 enhancement not correlated with a CO increase at the same altitude.

  17. In Situ Measurements of Aerosol Mass Concentration and Spectral Absorption at Three Location in and Around Mexico City

    NASA Astrophysics Data System (ADS)

    Chaudhry, Z.; Martins, V.; Li, Z.

    2006-12-01

    As a result of population growth and increasing industrialization, air pollution in heavily populated urban areas is one of the central environmental problems of the century. As a part of the MILAGRO (Megacity Initiative: Local and Global Research Observations) study, Nuclepore filters were collected in two size ranges (PM10 and PM2.5) at 12 hour intervals at three location in Mexico during March, 2006. Sampling stations were located at the Instituto Mexicano del Petroleo (T0), at the Rancho La Bisnago in the State of Hidalgo (T2) and along the Gulf Coast in Tampico (Tam). Each filter was analyzed for mass concentration, aerosol scattering and absorption efficiencies. Mass concentrations at T0 ranged from 47 to 179 μg/m3 for PM10 with an average concentration of 96 μg/m3, and from 20 to 93 μg/m3 for PM2.5 with an average concentration of 41 μg/m3. Mass concentrations at T2 ranged from 12 to 154 μg/m3 for PM10 with an average concentration of 51 μg/m3, and from 7 to 50 μg/m3 for PM2.5 with an average concentration of 25 μg/m3. Mass concentrations at Tam ranged from 34 to 80 μg/m3 for PM10 with an average concentration of 52 μg/m3, and from 8 to 23 μg/m3 for PM2.5 with an average concentration of 13 μg/m3. While some of the extreme values are likely linked to local emissions, regional air pollution episodes also played important roles. Each of the sampling stations experienced a unique atmospheric condition. The site at T0 was influenced by urban air pollution and dust storms, the site at T2 was significantly less affected by air pollution but more affected by regional dust storms and local dust devils while Tam was influenced by air pollution, dust storms and the natural marine environment. The spectral mass absorption efficiency was measured from 350 to 2500 nm and shows large differences between the absorption properties of soil dust, black carbon, and organic aerosols. The strong spectral differences observed can be related to differences in

  18. Evaluation of the discmini personal aerosol monitor for submicrometer sodium chloride and metal aerosols

    NASA Astrophysics Data System (ADS)

    Mills, Jessica Breyan

    This work evaluated the robust, lightweight DiSCmini (DM) aerosol monitor for its ability to measure the concentration and mean diameter of submicrometer aerosols. Tests were conducted with monodispersed and polydispersed aerosols composed of two particle types (sodium chloride, NaCl, and spark generated metal particles, which simulate particles found in welding fume) at three different steady-state concentration ranges (Low, <103; Medium, 103-104; and High, >104 particles/cm3). Particle number concentration, lung deposited surface area (LDSA) concentration, and mean size measured with the DM were compared to those measured with reference instruments, a scanning mobility particle sizer (SMPS) and a handheld condensation particle counter (CPC). Particle number concentrations measured with the DM were within 16% of those measured by the CPC for polydispersed aerosols. Poorer agreement was observed for monodispersed aerosols (+/-35% for most tests and +101% for 300-nm NaCl). LDSA concentrations measured by the DM were 96% to 155% of those estimated with the SMPS. The geometric mean diameters measured with the DM were within 30% of those measured with the SMPS for monodispersed aerosols and within 25% for polydispersed aerosols (except for the case when the aerosol contained a substantial number of particles larger than 300 nm). The accuracy of the DM is reasonable for particles smaller than 300 nm but caution should be exercised when particles larger than 300 nm are present.

  19. Changes in ground-level PM mass concentration and column aerosol optical depth over East Asia during 2004-2014

    NASA Astrophysics Data System (ADS)

    Nam, J.; Kim, S. W.; Park, R.; Yoon, S. C.; Sugimoto, N.; Park, J. S.; Hong, J.

    2015-12-01

    Multi-year records of moderate resolution imaging spectroradiometer (MODIS), ground-level particulate matter (PM) mass concentration, cloud-aerosol lidar with orthogonal polarization (CALIOP), and ground-level lidar were analyzed to investigate seasonal and annual changes of aerosol optical depth (AOD) and PM mass concentration over East Asia. Least mean square fit method is applied to detect the trends and their magnitudes for each selected regions and stations. Eleven-year MODIS measurements show generally increasing trends in both AOD (1.18 % yr-1) and Ångström exponent (0.98 % yr-1), especially over the east coastal industrialized region in China. Monthly variation of AOD show maximum value at April-July, which were related to the progress of summer monsoon rain band and stationary continental air mass on the northeast of Asia. Increasing trends of AOD were found for eight cites in China (0.80 % yr-1) and Seoul site, Korea (0.40 % yr-1), whereas no significant change were shown in Gosan background site (0.04 % yr-1) and decreasing trend at five background sites in Japan (-0.42 % yr-1). Contrasting to AOD trend, all fifteen sites in China (-1.28 % yr-1), Korea (-2.77 % yr-1), and Japan (-2.03 % yr-1) showed decreasing trend of PM10 mass concentration. Also, PM2.5 mass concentration at Beijing, Seoul, Rishiri, and Oki show significant decreasing trend of -1.16 % yr-1. To further discuss the opposite trend of surface PM mass concentration and column AOD, we investigate vertical aerosol profile from lidar measurements. AOD estimated for planetary boundary layer (surface~1.5 km altitude; AODPBL) from CALIOP measurements over East China show decreasing trend of -1.71 % yr-1 over the period of 2007-2014, wherever AOD estimated for free troposphere (1.5 km~5 km altitude; AODFT) show increasing trend of 2.92 % yr-1. In addition, ground-level lidar measurements in Seoul show decreasing AODPBL trend of -2.57 % yr-1, whereas, AODFT show no significant change (-0.44 % yr

  20. Effect of oxidant concentration, exposure time, and seed particles on secondary organic aerosol chemical composition and yield

    DOE PAGESBeta

    Lambe, A. T.; Chhabra, P. S.; Onasch, T. B.; Brune, W. H.; Hunter, J. F.; Kroll, J. H.; Cummings, M. J.; Brogan, J. F.; Parmar, Y.; Worsnop, D. R.; et al

    2015-03-18

    We performed a systematic intercomparison study of the chemistry and yields of secondary organic aerosol (SOA) generated from OH oxidation of a common set of gas-phase precursors in a Potential Aerosol Mass (PAM) continuous flow reactor and several environmental chambers. In the flow reactor, SOA precursors were oxidized using OH concentrations ranging from 2.0 × 108 to 2.2 × 1010 molec cm-3 over exposure times of 100 s. In the environmental chambers, precursors were oxidized using OH concentrations ranging from 2 × 106 to 2 × 107 molec cm-3 over exposure times of several hours. The OH concentration in themore » chamber experiments is close to that found in the atmosphere, but the integrated OH exposure in the flow reactor can simulate atmospheric exposure times of multiple days compared to chamber exposure times of only a day or so. In most cases, for a specific SOA type the most-oxidized chamber SOA and the least-oxidized flow reactor SOA have similar mass spectra, oxygen-to-carbon and hydrogen-to-carbon ratios, and carbon oxidation states at integrated OH exposures between approximately 1 × 1011 and 2 × 1011 molec cm-3 s, or about 1–2 days of equivalent atmospheric oxidation. This observation suggests that in the range of available OH exposure overlap for the flow reactor and chambers, SOA elemental composition as measured by an aerosol mass spectrometer is similar whether the precursor is exposed to low OH concentrations over long exposure times or high OH concentrations over short exposure times. This similarity in turn suggests that both in the flow reactor and in chambers, SOA chemical composition at low OH exposure is governed primarily by gas-phase OH oxidation of the precursors rather than heterogeneous oxidation of the condensed particles. In general, SOA yields measured in the flow reactor are lower than measured in chambers for the range of equivalent OH exposures that can be measured in both the flow reactor and chambers. The influence of

  1. On-line measurement of perchlorate in atmospheric aerosol based on ion chromatograph coupled with particle collector and post-column concentrator.

    PubMed

    Takeuchi, Masaki; Yoshioka, Kaoru; Toyama, Yusuke; Kagami, Ai; Tanaka, Hideji

    2012-08-15

    An automated analysis system has been developed for measuring perchlorate concentration in atmospheric aerosol. The perchlorate in aerosol sample, which has been collected with water mist in a hydrophobic filter/mist chamber based particle collector, is continuously preconcentrated. The matrix ions such as sulfate are subsequently removed from the preconcentrator. The remaining perchlorate is then analyzed on-line with an ion chromatograph in conjunction with a Nafion membrane tube based post-column concentrator. The sensitivity is increased by a factor of 7.7 with the post-column concentration technique. The proposed system has been successfully operated at Tokushima, Japan. The limit of detection is 0.35 ng/m(3) for 3 h sampling cycle. The perchlorate concentration in the atmospheric aerosol averaged 1.01±1.75 ng/m(3) (n=12). PMID:22841118

  2. Number size distributions and seasonality of submicron particles in Europe 2008-2009

    NASA Astrophysics Data System (ADS)

    Asmi, A.; Wiedensohler, A.; Laj, P.; Fjaeraa, A.-M.; Sellegri, K.; Birmili, W.; Weingartner, E.; Baltensperger, U.; Zdimal, V.; Zikova, N.; Putaud, J.-P.; Marinoni, A.; Tunved, P.; Hansson, H.-C.; Fiebig, M.; Kivekäs, N.; Lihavainen, H.; Asmi, E.; Ulevicius, V.; Aalto, P. P.; Swietlicki, E.; Kristensson, A.; Mihalopoulos, N.; Kalivitis, N.; Kalapov, I.; Kiss, G.; de Leeuw, G.; Henzing, B.; Harrison, R. M.; Beddows, D.; O'Dowd, C.; Jennings, S. G.; Flentje, H.; Weinhold, K.; Meinhardt, F.; Ries, L.; Kulmala, M.

    2011-03-01

    Two years of harmonized aerosol number size distribution data from 24 European field monitoring sites have been analysed. The results give a comprehensive overview of the European near surface aerosol particle number concentrations and number size distributions between 30 and 500 nm of dry particle diameter. Spatial and temporal distribution of aerosols in the particle sizes most important for climate applications are presented. We also analyse the annual, weekly and diurnal cycles of the aerosol number concentrations, provide log-normal fitting parameters for median number size distributions, and give guidance notes for data users. Emphasis is placed on the usability of results within the aerosol modelling community. We also show that the aerosol number concentrations of Aitken and accumulation mode particles (with 100 nm dry diameter as a cut-off between modes) are related, although there is significant variation in the ratios of the modal number concentrations. Different aerosol and station types are distinguished from this data and this methodology has potential for further categorization of stations aerosol number size distribution types. The European submicron aerosol was divided into characteristic types: Central European aerosol, characterized by single mode median size distributions, unimodal number concentration histograms and low variability in CCN-sized aerosol number concentrations; Nordic aerosol with low number concentrations, although showing pronounced seasonal variation of especially Aitken mode particles; Mountain sites (altitude over 1000 m a.s.l.) with a strong seasonal cycle in aerosol number concentrations, high variability, and very low median number concentrations. Southern and Western European regions had fewer stations, which decreases the regional representativeness of these results. Aerosol number concentrations over the Britain and Ireland had very high variance and there are indications of mixed air masses from several source regions

  3. Number size distributions and seasonality of submicron particles in Europe 2008-2009

    NASA Astrophysics Data System (ADS)

    Asmi, A.; Wiedensohler, A.; Laj, P.; Fjaeraa, A.-M.; Sellegri, K.; Birmili, W.; Weingartner, E.; Baltensperger, U.; Zdimal, V.; Zikova, N.; Putaud, J.-P.; Marinoni, A.; Tunved, P.; Hansson, H.-C.; Fiebig, M.; Kivekäs, N.; Lihavainen, H.; Asmi, E.; Ulevicius, V.; Aalto, P. P.; Swietlicki, E.; Kristensson, A.; Mihalopoulos, N.; Kalivitis, N.; Kalapov, I.; Kiss, G.; de Leeuw, G.; Henzing, B.; Harrison, R. M.; Beddows, D.; O'Dowd, C.; Jennings, S. G.; Flentje, H.; Weinhold, K.; Meinhardt, F.; Ries, L.; Kulmala, M.

    2011-06-01

    Two years of harmonized aerosol number size distribution data from 24 European field monitoring sites have been analysed. The results give a comprehensive overview of the European near surface aerosol particle number concentrations and number size distributions between 30 and 500 nm of dry particle diameter. Spatial and temporal distribution of aerosols in the particle sizes most important for climate applications are presented. We also analyse the annual, weekly and diurnal cycles of the aerosol number concentrations, provide log-normal fitting parameters for median number size distributions, and give guidance notes for data users. Emphasis is placed on the usability of results within the aerosol modelling community. We also show that the aerosol number concentrations of Aitken and accumulation mode particles (with 100 nm dry diameter as a cut-off between modes) are related, although there is significant variation in the ratios of the modal number concentrations. Different aerosol and station types are distinguished from this data and this methodology has potential for further categorization of stations aerosol number size distribution types. The European submicron aerosol was divided into characteristic types: Central European aerosol, characterized by single mode median size distributions, unimodal number concentration histograms and low variability in CCN-sized aerosol number concentrations; Nordic aerosol with low number concentrations, although showing pronounced seasonal variation of especially Aitken mode particles; Mountain sites (altitude over 1000 m a.s.l.) with a strong seasonal cycle in aerosol number concentrations, high variability, and very low median number concentrations. Southern and Western European regions had fewer stations, which decreases the regional coverage of these results. Aerosol number concentrations over the Britain and Ireland had very high variance and there are indications of mixed air masses from several source regions; the

  4. Automated Analysis of Human Sperm Number and Concentration (Oligospermia) Using Otsu Threshold Method and Labelling

    NASA Astrophysics Data System (ADS)

    Susrama, I. G.; Purnama, K. E.; Purnomo, M. H.

    2016-01-01

    Oligospermia is a male fertility issue defined as a low sperm concentration in the ejaculate. Normally the sperm concentration is 20-120 million/ml, while Oligospermia patients has sperm concentration less than 20 million/ml. Sperm test done in the fertility laboratory to determine oligospermia by checking fresh sperm according to WHO standards in 2010 [9]. The sperm seen in a microscope using a Neubauer improved counting chamber and manually count the number of sperm. In order to be counted automatically, this research made an automation system to analyse and count the sperm concentration called Automated Analysis of Sperm Concentration Counters (A2SC2) using Otsu threshold segmentation process and morphology. Data sperm used is the fresh sperm directly in the analysis in the laboratory from 10 people. The test results using A2SC2 method obtained an accuracy of 91%. Thus in this study, A2SC2 can be used to calculate the amount and concentration of sperm automatically

  5. Influences of vertical transport and scavenging on aerosol particle surface area and radon decay product concentrations at the Jungfraujoch (3454 m above sea level)

    NASA Astrophysics Data System (ADS)

    Lugauer, M.; Baltensperger, U.; Furger, M.; GäGgeler, H. W.; Jost, D. T.; Nyeki, S.; Schwikowski, M.

    2000-08-01

    Concentrations of the aerosol particle surface area (SA) and aerosol-attached radon decay products 214Pb and 212Pb have been measured by means of an aerosol and a radon epiphaniometer at the Jungfraujoch research station (JFJ; 3454 m above sea level, Switzerland). These parameters exhibit a pronounced seasonal cycle with minimum values in winter and maximum values in summer. In summer, pronounced diurnal variations with a maximum at 1800 LST are often present. Highest concentrations and most pronounced diurnal variations occur during anticyclonic weather conditions in summer. Thermally driven vertical transport over alpine topography is responsible for this observation. During this synoptic condition, concentrations vary greatly with the 500 hPa wind direction, exhibiting low concentrations for NW-N winds and high concentrations for weak or S-SW winds. Lead-214 and SA are highly correlated during anticyclonic conditions, indicating transport equivalence of the gaseous 214Pb precursor, 222Rn, and of aerosol particles. When cyclonic lifting is the dominant vertical transport, wet scavenging of aerosol particles can explain the weak correlation of 214Pb and SA. This conclusion is corroborated by the 214Pb/SA ratio, being twice as high during cyclonic than during anticyclonic conditions. Lead-212 is a tracer for the influence of surface contact on a local scale due to its short lifetime of 15.35 hours. The analysis of this parameter suggests that high-alpine surfaces play an important role in thermally driven transport to the JFJ.

  6. Exposure to particle number, surface area and PM concentrations in pizzerias

    NASA Astrophysics Data System (ADS)

    Buonanno, G.; Morawska, L.; Stabile, L.; Viola, A.

    2010-10-01

    The aim of this work was to quantify exposure to particles emitted by wood-fired ovens in pizzerias. Overall, 15 microenvironments were chosen and analyzed in a 14-month experimental campaign. Particle number concentration and distribution were measured simultaneously using a Condensation Particle Counter (CPC), a Scanning Mobility Particle Sizer (SMPS), an Aerodynamic Particle Sizer (APS). The surface area and mass distributions and concentrations, as well as the estimation of lung deposition surface area and PM 1 were evaluated using the SMPS-APS system with dosimetric models, by taking into account the presence of aggregates on the basis of the Idealized Aggregate (IA) theory. The fraction of inhaled particles deposited in the respiratory system and different fractions of particulate matter were also measured by means of a Nanoparticle Surface Area Monitor (NSAM) and a photometer (DustTrak DRX), respectively. In this way, supplementary data were obtained during the monitoring of trends inside the pizzerias. We found that surface area and PM 1 particle concentrations in pizzerias can be very high, especially when compared to other critical microenvironments, such as the transport hubs. During pizza cooking under normal ventilation conditions, concentrations were found up to 74, 70 and 23 times higher than background levels for number, surface area and PM 1, respectively. A key parameter is the oven shape factor, defined as the ratio between the size of the face opening in respect to the diameter of the semicircular oven door, and particular attention must also be paid to hood efficiency.

  7. 40 CFR Table F-5 to Subpart F of... - Estimated Mass Concentration Measurement of PM2.5 for Idealized “Typical” Coarse Aerosol Size...

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 5 2011-07-01 2011-07-01 false Estimated Mass Concentration... 53—Estimated Mass Concentration Measurement of PM2.5 for Idealized “Typical” Coarse Aerosol Size Distribution Particle Aerodynamic Diameter (µm) Test Sampler Fractional Sampling Effectiveness Interval...

  8. 40 CFR Table F-5 to Subpart F of... - Estimated Mass Concentration Measurement of PM 2.5 for Idealized “Typical” Coarse Aerosol Size...

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 6 2014-07-01 2014-07-01 false Estimated Mass Concentration... 53—Estimated Mass Concentration Measurement of PM 2.5 for Idealized “Typical” Coarse Aerosol Size Distribution Particle Aerodynamic Diameter (µm) Test Sampler Fractional Sampling Effectiveness Interval...

  9. 40 CFR Table F-5 to Subpart F of... - Estimated Mass Concentration Measurement of PM2.5 for Idealized “Typical” Coarse Aerosol Size...

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 6 2012-07-01 2012-07-01 false Estimated Mass Concentration... 53—Estimated Mass Concentration Measurement of PM2.5 for Idealized “Typical” Coarse Aerosol Size Distribution Particle Aerodynamic Diameter (µm) Test Sampler Fractional Sampling Effectiveness Interval...

  10. 40 CFR Table F-5 to Subpart F of... - Estimated Mass Concentration Measurement of PM 2.5 for Idealized “Typical” Coarse Aerosol Size...

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 6 2013-07-01 2013-07-01 false Estimated Mass Concentration... 53—Estimated Mass Concentration Measurement of PM 2.5 for Idealized “Typical” Coarse Aerosol Size Distribution Particle Aerodynamic Diameter (µm) Test Sampler Fractional Sampling Effectiveness Interval...

  11. 40 CFR Table F-5 to Subpart F of... - Estimated Mass Concentration Measurement of PM2.5 for Idealized “Typical” Coarse Aerosol Size...

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Estimated Mass Concentration... 53—Estimated Mass Concentration Measurement of PM2.5 for Idealized “Typical” Coarse Aerosol Size Distribution Particle Aerodynamic Diameter (µm) Test Sampler Fractional Sampling Effectiveness Interval...

  12. Temporal and spatial effects of ablation plume on number density distribution of droplets in an aerosol measured by laser-induced breakdown

    NASA Astrophysics Data System (ADS)

    Yashiro, H.; Kakehata, M.

    2013-05-01

    We proposed and experimentally demonstrated a novel method of evaluating the number density of droplets in an aerosol by laser-induced breakdown. The number density of droplets is evaluated from the volume in which the laser intensity exceeds the breakdown threshold intensity for droplets, and the number of droplets in this volume, which is evaluated by the experimentally observed breakdown probability. This measurement method requires a large number of laser shots for not only precise measurement but also highly temporally and spatially resolved density distribution in aerosol. Laser ablation plumes ejected from liquid droplets generated by breakdown disturb the density around the measurement points. Therefore, the recovery time of the density determines the maximum repetition rate of the probe laser irradiating a fixed point. The expansion range of the ablation plume determines the minimum distance at which the measurement points are unaffected by a neighboring breakdown when multiple laser beams are simultaneously irradiated. These laser irradiation procedures enable the measurement of the number density distribution of droplets in an aerosol at a large number of points within a short measurement time.

  13. Temporal and spatial effects of ablation plume on number density distribution of droplets in an aerosol measured by laser-induced breakdown

    SciTech Connect

    Yashiro, H.; Kakehata, M.

    2013-05-07

    We proposed and experimentally demonstrated a novel method of evaluating the number density of droplets in an aerosol by laser-induced breakdown. The number density of droplets is evaluated from the volume in which the laser intensity exceeds the breakdown threshold intensity for droplets, and the number of droplets in this volume, which is evaluated by the experimentally observed breakdown probability. This measurement method requires a large number of laser shots for not only precise measurement but also highly temporally and spatially resolved density distribution in aerosol. Laser ablation plumes ejected from liquid droplets generated by breakdown disturb the density around the measurement points. Therefore, the recovery time of the density determines the maximum repetition rate of the probe laser irradiating a fixed point. The expansion range of the ablation plume determines the minimum distance at which the measurement points are unaffected by a neighboring breakdown when multiple laser beams are simultaneously irradiated. These laser irradiation procedures enable the measurement of the number density distribution of droplets in an aerosol at a large number of points within a short measurement time.

  14. Highly time-resolved trace element concentrations in aerosols during the Megapoli Paris campaigns

    NASA Astrophysics Data System (ADS)

    Furger, Markus; Visser, Suzanne; Slowik, Jay G.; Crippa, Monica; Poulain, Laurent; Appel, Karen; Flechsig, Uwe; Prevot, Andre S. H.; Baltensperger, Urs

    2014-05-01

    Trace elements contribute typically only a few percent to the total mass of air pollutants, however, they can affect the environment in significant ways, especially those that are toxic. Furthermore, they are advantageous with respect to a refinement of source apportionment when measured with high time resolution and appropriate size segregation. This approach is especially advantageous in an urban environment with numerous time-variant emission sources distributed across a relatively narrow space, as is typically the setting of a megacity. Two 1-month long field campaigns took place in the framework of the Megapoli project in Paris, France, in the summer of 2009 and in the winter of 2010. Rotating drum impactors (RDI) were operated at two sites in each campaign, one urban, the other one suburban. The RDI segregated the aerosols into three size ranges (PM10-2.5, PM2.5-1 and PM1-0.1) and sampled with 2-hour time resolution. The samples were analyzed with synchrotron radiation induced X-ray fluorescence spectrometry (SR-XRF) at the synchrotron facilities of Paul Scherrer Institute (SLS) and Deutsches Elektronen-Synchrotron (HASYLAB), where a broad range of elements (Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Se, Sr, Zr, Cd, Sn, Sb, Ba, Pb) was analyzed for each size range. Time series of the analyzed elements for the different sites and campaigns were prepared to characterize the aerosol trace element composition and temporal behavior for the different weather situations and urban environments. They allow for the distinction of regional vs. local sources and transport, and provide a basis for source apportionment calculations. Local and regional contributions of traffic, including re-suspension, break wear and exhaust, wood burning, marine and other sources will be discussed. Indications of long-range transport from Polish coal emissions in the city center of Paris were also found.

  15. Spatial-temporal variations of particle number concentrations between a busy street and the urban background

    NASA Astrophysics Data System (ADS)

    Dos Santos-Juusela, Vanessa; Petäjä, Tuukka; Kousa, Anu; Hämeri, Kaarle

    2013-11-01

    To estimate spatial-temporal variations of ultrafine particles (UFP) in Helsinki, we measured particle total number concentrations (PNC) continuously in a busy street and an urban background site for six months, using condensation particle counters (CPC). We also evaluated the effects of temperature, wind speed and wind direction on PNC, as well as the correlation between PNC and PM2.5, PM10 and black carbon (BC) at the street. We found that on weekdays, hourly median PNC were highly correlated with BC (r = 0.88), moderately correlated with PM2.5 (r = 0.59) and weakly correlated with PM10 (r = 0.22). Number concentrations at the street were inversely proportional to temperature and wind speed, and highly dependent on wind direction. The highest PNC occurred during northeastern winds while the lowest occurred during southwestern winds. As these wind directions are nearly perpendicular to the street axis, the formation of wind vortices may have influenced the dispersion of UFP in the site. Although the temporal correlation for PNC was moderately high between the sites (r = 0.71), the median concentration at the street was 3 times higher than the urban background levels. The results indicate that people living or passing by the busy street are exposed to UFP concentrations well above the urban background levels. Thus, the study suggests that urban microenvironments should be considered in epidemiological studies. In addition the results emphasize that regulations based solely on PM2.5 and PM10 concentrations may be insufficient for preventing the adverse health effects of airborne particles.

  16. The effects of vegetation barriers on near-road ultrafine particle number and carbon monoxide concentrations.

    PubMed

    Lin, Ming-Yeng; Hagler, Gayle; Baldauf, Richard; Isakov, Vlad; Lin, Hong-Yiou; Khlystov, Andrey

    2016-05-15

    Numerous studies have shown that people living in near-roadway communities (within 100 m of the road) are exposed to high ultrafine particle (UFP) number concentrations, which may be associated with adverse health effects. Vegetation barriers have been shown to affect pollutant transport via particle deposition to leaves and altering the dispersion of emission plumes, which in turn would modify the exposure of near-roadway communities to traffic-related UFPs. In this study, both stationary (equipped with a Scanning Mobility Particle Sizer, SMPS) and mobile (equipped with Fast Mobility Particle Sizer, FMPS) measurements were conducted to investigate the effects of vegetation barriers on downwind UFP (particle diameters ranging from 14 to 102 nm) concentrations at two sites in North Carolina, USA. One site had mainly deciduous vegetation while the other was primarily coniferous; both sites have a nearby open field without the vegetation barriers along the same stretch of limited access road, which served as a reference. During downwind conditions (traffic emissions transported towards the vegetation barrier) and when the wind speed was above or equal to 0.5m/s, field measurements indicated that vegetation barriers with full foliage reduced UFP and CO concentrations by 37.7-63.6% and 23.6-56.1%, respectively. When the test was repeated at the same sites during winter periods when deciduous foliage was reduced, the deciduous barrier during winter showed no significant change in UFP concentration before and after the barrier. Results from the stationary (using SMPS) and mobile (using FMPS) measurements for UFP total number concentrations generally agreed to within 20%. PMID:26930311

  17. Source apportionment of elevated BaP concentrations in PM10 aerosols in an alpine valley in Austria

    NASA Astrophysics Data System (ADS)

    Bauer, Heidi; Puxbaum, Hans; Jankowski, Nicole; Sampaio Cordeiro Wagner, Lylian

    2010-05-01

    INTRODUCTION: In a village situated at 1215 m a.s.l. in a natural preserve in an Austrian alpine valley elevated BaP concentrations have been measured in the last years. A highly frequented highway leading from Italy to Germany passes near the village. Monthly means of particulate BaP concentrations show a clear seasonal trend with values below 1 ng/m³ during the warmer months and with concentrations up to 9 ng/m³ in the cold season. Annual averages in the years 2000 - 2005 ranged between 1.4 and 2.8 ng/m³ - much higher than the EU target value of 1 ng/m³. We used a macrotracer model developed at the Vienna University of Technology to determine the contributions of the sources for BaP emissions, which were mainly space heating with wood and traffic from the highway. EXPERIMENTAL: The macrotracer concept is a nine component model to derive source contribution and explains 80-100% of PM10 aerosols in Austria. The amount of traffic exhaust is derived by using EC as tracer, whereas EC produced by wood burning is subtracted, the amount of wood smoke is derived by the anhydro-sugar levoglucosan and the ratio between the anhydro-sugars levoglucosan and mannosan. For the source apportionment of BaP the applied factors reflect on the one hand the composition of the automotive fleet in Austria and on the other hand the composition of the fire wood in the region. Filter samples collected with a high volume sampler in winter were analyzed for PM10 aerosol mass, total, organic, elemental and carbonate carbon, HULIS, anhydro-sugars, polyols and ions (major ions and organic acids) and PAHs. In the same way emission samples taken at a motor test stand and at a test stand for wood combustion were analyzed (Schmidl et al. 2008). The saccharides were determined using high pH anion exchange and pulsed amperometry (HPAE-PAD). Details of the analytical method are given in Iinuma et al., 2009. Elemental and organic carbon were determined with a thermal-optical instrument (Sunset lab

  18. Number concentration and chemical composition of ultrafine and nanoparticles from WTE (waste to energy) plants.

    PubMed

    Cernuschi, Stefano; Giugliano, Michele; Ozgen, Senem; Consonni, Stefano

    2012-03-15

    Stack field testing at four municipal waste-to-energy (WTE) plants was conducted to investigate total number concentrations and size distributions in a size range extended towards the evaluation of ultrafine (UFP) and nanoparticle (NP) fractions with diameters smaller than 100nm and 50nm, respectively. Measurements were performed with a specifically designed sampling line, equipped with a dilution system and a particle counting device for measuring both primary particles in raw flue gases at stack conditions and the contributions of condensable origin, arising from their cooling and dilution immediately following stack release into the atmosphere. Average concentration levels detected ranged between 5×10(3)-6×10(5)cm(-3): for all sampling conditions, ultrafine fractions largely prevailed in number size distributions, with average diameters constantly located in the nanoparticle size range. Stack concentrations appeared to be influenced by the design and process configuration of flue gas cleaning systems, with most significant effects related to the presence of wet scrubbing units and the baghouse operating temperature of dry removal processes. Chemical speciation (i.e., trace metals, anions and cations, carbonaceous compounds) of size-resolved particulate fractions was performed on one of the plants. NP and UFP composition was essentially in accordance with the most important fuel and combustion process characteristics: in particular, the presence of chlorides and metal species was consistent with the respective waste feed content and their expected behavior during combustion and flue gas cleaning processes. PMID:22326138

  19. Characterization of a Vortex Shaking Method for Aerosolizing Fibers

    PubMed Central

    Ku, Bon Ki; Deye, Gregory; Turkevich, Leonid A.

    2015-01-01

    Generation of well-dispersed, well-characterized fibers is important in toxicology studies. A vortex-tube shaking method is investigated using glass fibers to characterize the generated aerosol. Controlling parameters that were studied included initial batch amounts of glass fibers, preparation of the powder (e.g., preshaking), humidity, and airflow rate. Total fiber number concentrations and aerodynamic size distributions were typically measured. The aerosol concentration is only stable for short times (t < 10 min) and then falls precipitously, with concomitant changes in the aerosol aerodynamic size distribution; the plateau concentration and its duration both increase with batch size. Preshaking enhances the initial aerosol concentration and enables the aerosolization of longer fibers. Higher humidity strongly affects the particle size distribution and the number concentration, resulting in a smaller modal diameter and a higher number concentration. Running the vortex shaker at higher flow rates (Q > 0.3 lpm), yields an aerosol with a particle size distribution representative of the batch powder; running the vortex shaker at a lower aerosol flow rate (Q ~ 0.1 lpm) only aerosolizes the shorter fibers. These results have implications for the use of the vortex shaker as a standard aerosol generator. PMID:26635428

  20. Aerosol cloud processing with the global model ECHAM5-HAM-SALSA

    NASA Astrophysics Data System (ADS)

    Bergman, T.; Korhonen, H.; Zubair, M.; Romakkaniemi, S.; Lehtinen, K.; Kokkola, H.

    2012-04-01

    Atmospheric aerosols and their interactions with clouds constitute the largest uncertainty in the radiative forcing of the Earth's atmosphere. Increasing aerosol number concentrations increases the cloud droplet concentration and droplet surface and hence the cloud albedo. This mechanism is called the aerosol indirect effect on climate. Understanding the changes in cloud droplet number concentrations and size by anthropogenic aerosols are the key factors in the study of future climate change. Therefore the aerosols' formation and growth from nanoparticles to cloud condensation nuclei (CCN) must be described accurately. The formation and growth of aerosols are shown to be described more accurately with sectional representations than with bulk (total aerosol mass only), modal (lognormal modes describing mass and number size distribution) or moment (processes tied to different moments of particle number size distribution) approaches. Recently the sectional aerosol models have been implemented to global climate models. However, the resolution of sectional models must be optimised to reduce the computational cost. We have implemented the sectional aerosol model SALSA in ECHAM5-HAM. SALSA describes the aerosol population with 20 size sections. The dynamics are optimised for large scale applications and the model includes an improved moving center sectional method. The particulate mass consists of five compounds: sulphate, organic carbon, black carbon, sea salt and dust. The aerosol processing has been studied extensively and there are many numerical models used to predict CCN number concentrations. However, due to computational limitations many of them are not suitable for utilisation in global climate models. Therefore in most global climate studies on aerosol activation to CCN is examined using cloud activation parameterisations. We study the aerosol cloud processing and its affect on transport of aerosols using Abdul-Razzak-Ghan aerosol cloud activation

  1. 40 CFR Table C-1 to Subpart C of... - Test Concentration Ranges, Number of Measurements Required, and Maximum Discrepancy Specifications

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 6 2013-07-01 2013-07-01 false Test Concentration Ranges, Number of... Reference Methods Pt. 53, Subpt. C, Table C-1 Table C-1 to Subpart C of Part 53—Test Concentration Ranges, Number of Measurements Required, and Maximum Discrepancy Specifications Pollutant Concentration...

  2. 40 CFR Table C-1 to Subpart C of... - Test Concentration Ranges, Number of Measurements Required, and Maximum Discrepancy Specifications

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 6 2014-07-01 2014-07-01 false Test Concentration Ranges, Number of... Reference Methods Pt. 53, Subpt. C, Table C-1 Table C-1 to Subpart C of Part 53—Test Concentration Ranges, Number of Measurements Required, and Maximum Discrepancy Specifications Pollutant Concentration...

  3. 40 CFR Table C-1 to Subpart C of... - Test Concentration Ranges, Number of Measurements Required, and Maximum Discrepancy Specifications

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 6 2012-07-01 2012-07-01 false Test Concentration Ranges, Number of... Reference Methods Pt. 53, Subpt. C, Table C-1 Table C-1 to Subpart C of Part 53—Test Concentration Ranges, Number of Measurements Required, and Maximum Discrepancy Specifications Pollutant Concentration...

  4. Evaluation of indoor aerosol control devices and their effects on radon progeny concentrations

    SciTech Connect

    Sextro, R.G.; Offermann, F.J.; Nazaroff, W.W.; Nero, A.V.; Revzan, K.L.; Yater, J.

    1984-02-01

    Eleven portable air cleaning devices have been evaluated for control of indoor concentrations of respirable particles, and their concomitant effects on radon progeny concentrations have been investigated. Of the devices we examined the electrostatic precipitators and extended surface filters had significant particle removal rates, while the particle removal rates for several small panel-filters, an ion-generator, and a pair of mixing fans were found to be negligible. The evaluation of radon progeny control produced similar results; the air cleaners which were effective in removing particles were also effective in reducing radon progeny concentrations. Furthermore, at the low particle concentrations, plateout of the unattached radon progeny was found to be a significant removal mechanism. The overall removal rates due to deposition of attached and unattached progeny have been estimated from these data, and the equilibrium factors for total and unattached progeny concentrations have been calculated as a function of particle concentration. 7 references, 2 figures.

  5. Reducing the number of fish in bioconcentration studies with general chemicals by reducing the number of test concentrations.

    PubMed

    Burden, Natalie; Creton, Stuart; Weltje, Lennart; Maynard, Samuel K; Wheeler, James R

    2014-11-01

    Fish bioconcentration test guidelines generally require that bioconcentration factors (BCFs) are determined at two exposure concentrations. However, recent revisions to the OECD test guideline for bioconcentration testing (TG 305) provide the option to use only one exposure concentration, when justification is provided, although two concentrations may still be required for some regulatory purposes. Recently, this justification has been demonstrated for plant protection product active ingredients. To determine whether this justification has a broader validity for general chemicals, an analysis of 236 BCF studies on general chemicals was conducted. The results presented here again demonstrate that BCF values do not significantly differ between concentrations when more than one concentration is used. This relationship is particularly strong for BCFs ⩾1000L/kg, which is beneficial, since only chemicals with BCFs >2000L/kg may require regulatory action. This analysis therefore provides a data-driven rationale for using the one test concentration approach for general chemical substances and thus could contribute to a substantial reduction in the use of fish in bioconcentration tests. PMID:25128673

  6. Aerosol size distribution seasonal characteristics measured in Tiksi, Russian Arctic

    NASA Astrophysics Data System (ADS)

    Asmi, E.; Kondratyev, V.; Brus, D.; Laurila, T.; Lihavainen, H.; Backman, J.; Vakkari, V.; Aurela, M.; Hatakka, J.; Viisanen, Y.; Uttal, T.; Ivakhov, V.; Makshtas, A.

    2015-07-01

    Four years of continuous aerosol number size distribution measurements from an Arctic Climate Observatory in Tiksi Russia are analyzed. Source region effects on particle modal features, and number and mass concentrations are presented for different seasons. The monthly median total aerosol number concentration in Tiksi ranges from 184 cm-3 in November to 724 cm-3 in July with a local maximum in March of 481 cm-3. The total mass concentration has a distinct maximum in February-March of 1.72-2.38 μg m-3 and two minimums in June of 0.42 μg m-3 and in September-October of 0.36-0.57 μg m-3. These seasonal cycles in number and mass concentrations are related to isolated aerosol sources such as Arctic haze in early spring which increases accumulation and coarse mode numbers, and biogenic emissions in summer which affects the smaller, nucleation and Aitken mode particles. The impact of temperature dependent natural emissions on aerosol and cloud condensation nuclei numbers was significant. Therefore, in addition to the precursor emissions of biogenic volatile organic compounds, the frequent Siberian forest fires, although far are suggested to play a role in Arctic aerosol composition during the warmest months. During calm and cold months aerosol concentrations were occasionally increased by nearby aerosol sources in trapping inversions. These results provide valuable information on inter-annual cycles and sources of Arctic aerosols.

  7. Evolution of size-segregated aerosol mass concentration during the Antarctic summer at Northern Foothills, Victoria Land

    NASA Astrophysics Data System (ADS)

    Illuminati, Silvia; Bau, Sébastien; Annibaldi, Anna; Mantini, Caterina; Libani, Giulia; Truzzi, Cristina; Scarponi, Giuseppe

    2016-01-01

    Within the framework of the Italian National Programm for Antarctic Research (PNRA), the first direct gravimetric measurements of size-segregated aerosol fractions were carried out at Faraglione Camp, ˜3-km far from the Italian station "M. Zucchelli" (Terra Nova Bay, Ross Sea), during the 2014-2015 austral summer. A six-stage high-volume cascade impactor with size classes between 10 μm and 0.49 μm, and, in parallel, for comparison purposes, a PM10 high-volume sampler (50% cut-off aerodynamic diameter of 10 μm) were used. A 10-day sampling strategy was adopted. Aerosol mass measurements were carried out before and after exposure by using a microbalance specifically designed for the filter weight and placed inside a glove bag in order to maintain stable temperature and humidity conditions during weighing sessions. Measured atmospheric concentrations (referred to the "actual air conditions" of mean temperature of 268 K and mean pressure of 975 hPa) of size-segregated aerosol fractions showed the following values, given as size range, means (interquartile range): Dp < 0.49 μm, 0.33 (0.26-0.34) μg m-3; 0.49-0.95 μm, 0.20 (0.19-0.24) μg m-3; 0.95-1.5 μm, 0.16 (0.13-0.21) μg m-3; 1.5-3.0 μm 0.075 (0.05-0.11) μg m-3; 3.0-7.2 μm 0.12 (0.02-0.19) μg m-3; 7.2-10 μm 0.06 (0.01-0.03) μg m-3. The average mass concentration of the total PM10 at Faraglione Camp for the entire sampling period was 0.92 (0.67-1.1) μg m-3. Although a great variability, the aerosol mass concentration showed a tri-modal distribution, with an accumulation mode (in the range 0.1-1.0 μm) and two coarse modes (CM1 in the range 1.0-3.0 μm, and CM2 in the range 3.0-10 μm). From 50% to 90% of the PM10 mass comes from particles of a size smaller than 1.0 μm. The two coarse modes represented from ˜5% to ˜35% of the PM10, showing opposite seasonal trends (CM1 decreased while CM2 increased). During summer, PM10 mass concentration increased to a maximum of ˜1.6 μg m-3 at mid-December, while

  8. Global and regional evolution of short-lived radiatively-active gases and aerosols in the Representative Concentration Pathways

    SciTech Connect

    Lamarque, J.-F.; Kyle, G. Page; Meinshausen, Malte; Riahi, Keywan; Smith, Steven J.; Van Vuuren, Detlef; Conley, Andrew; Vitt, Francis

    2011-08-05

    In this paper, we discuss the results of 2000-2100 simulations with a chemistry-climate model, focusing on the changes in atmospheric composition (troposphere and stratosphere) following the emissions associated with the Representative Concentration Pathways. We show that tropospheric ozone is projected to decrease (RCP3PD and RCP4.5) or increase (RCP8.5) between 2000 and 2100. Surface ozone in 2100 is projected to change little compared from 2000 conditions, a much-reduced impact from the projections based on the A2 scenario. Aerosols are projected to strongly decrease in the 21st century, a reflection of their projected decrease in emissions. Similarly, sulfate deposition is projected to strongly decrease. However, nitrogen deposition is projected to increase over certain regions because of the projected increase NH3 emissions.

  9. A Simple Model of Global Aerosol Indirect Effects

    SciTech Connect

    Ghan, Steven J.; Smith, Steven J.; Wang, Minghuai; Zhang, Kai; Pringle, K. J.; Carslaw, K. S.; Pierce, Jeffrey; Bauer, Susanne E.; Adams, P. J.

    2013-06-28

    Most estimates of the global mean indirect effect of anthropogenic aerosol on the Earth’s energy balance are from simulations by global models of the aerosol lifecycle coupled with global models of clouds and the hydrologic cycle. Extremely simple models have been developed for integrated assessment models, but lack the flexibility to distinguish between primary and secondary sources of aerosol. Here a simple but more physically-based model expresses the aerosol indirect effect using analytic representations of droplet nucleation, cloud and aerosol vertical structure, and horizontal variability in cloud water and aerosol concentration. Although the simple model is able to produce estimates of aerosol indirect effects that are comparable to those from some global aerosol models using the same global mean aerosol properties, the estimates are found to be sensitive to several uncertain parameters, including the preindustrial cloud condensation nuclei concentration, primary and secondary anthropogenic emissions, the size of the primary particles, the fraction of the secondary anthropogenic emissions that accumulates on the coarse mode, the fraction of the secondary mass that forms new particles, and the sensitivity of liquid water path to droplet number concentration. Aerosol indirect effects are surprisingly linear in emissions. This simple model provides a much stronger physical basis for representing aerosol indirect effects than previous representations in integrated assessment models designed to quickly explore the parameter space of emissions-climate interactions. The model also produces estimates that depend on parameter values in ways that are consistent with results from detailed global aerosol-climate simulation models.

  10. Evaluation of indoor aerosol control devices and their effects on radon progeny concentrations. Revision

    SciTech Connect

    Sextro, R.G.; Offermann, F.J.; Nazaroff, W.W.; Nero, A.V.; Revzan, K.L.; Yater, J.

    1984-11-01

    Eleven portable air cleaning devices have been evaluated for control of indoor concentrations of respirable particles, and their concomitant effects on radon progeny concentrations have been investigated. The experiments were conducted in a room-size chamber using cigarette smoke and radon injection from an external source. Of the devices examined the electrostatic precipitators and extended surface filters had significant particle removal rates, while the particle removal rates for several small panel-filters, an ion-generator, and a pair of mixing fans were found to be essentially negligible. The evaluation of radon progeny control produced similar results; the air cleaners which were effective in removing particles were also effective in reducing radon progeny concentrations. At the low particle concentrations, deposition of the unattached radon progeny on room surfaces was found to be a significant removal mechanism. Deposition rates of attached and unattached progeny have been estimated from these data, and were used to calculate the equilibrium factors for total and unattached progeny concentrations as a function of particle concentration. While particle removal reduces total airborne radon progeny concentrations, the relative alpha decay dose to the lungs appears to change very little as the particle concentration decreases due to the greater radiological importance of unattached progeny.

  11. Combining AOT, Angstrom Exponent and PM concentration data, with PSCF model, to distinguish fine and coarse aerosol intrusions in Southern France

    NASA Astrophysics Data System (ADS)

    Dimitriou, Konstantinos; Kassomenos, Pavlos

    2016-05-01

    In this paper, a cluster analysis of backward air mass trajectories, arriving in Avignon (Southern France), was combined with a Potential Source Contribution Function (PSCF) model on a 0.5° × 0.5° resolution grid, in order to indicate possible aerosol intrusions. A strict triple criterion was constructed from Aerosol Optical Thickness (AOT), Angstrom Exponent (AE), and PM (PM10 and PM2.5) concentration measurements, aiming to distinguish more effectively Episodes of Fine, Coarse and Overall Aerosols (FAE, CAE and OAE respectively). Large fractions of FAE (60.0%) and CAE (40.6%) were strongly attributed to the prevalence of Eastern and South-Southwest (S-SW) airflows respectively, whereas these distinct trajectory clusters also gathered large fractions of OAE (90.2% cumulatively). According to PSCF results, FAE events were strongly associated with the influence of air masses traveling over North Italy and Southern Germany, hence the impact of urban and industrial combustion was emerged. Main sources of coarse aerosols were principally isolated over the Mediterranean, thus the import of sea spray and dust from the Sahara desert is presumed. Satellite AOT observations were used for a more detailed identification of an intense 5-day intrusion of coarse aerosols. Short range slow moving air mass trajectories, were proven to be a clear marker of atmospheric stagnation, based on a wind speed analysis, triggering the accumulation of locally emitted anthropogenic aerosols (mainly PM2.5) and lack of city ventilation.

  12. Total and size-resolved particle number and black carbon concentrations near an industrial area

    NASA Astrophysics Data System (ADS)

    Keuken, M. P.; Moerman, M.; Zandveld, P.; Henzing, J. S.

    2015-12-01

    Total and size-resolved particle number and black carbon concentrations were investigated in urban areas of the city of Rotterdam (the Netherlands) situated near an industrial area. Several monitoring campaigns were conducted in the period 2011-2014 at three local locations and at a regional background site. Black carbon levels showed minor elevation due to industrial emissions. In contrast, particle number concentrations (PNC) increased during periods with wind directions from the industrial area, by 1000 to 23,000 particles per cm3 depending on the distance to the area from 1 to 40 km. The size distribution of elevated PNC was characterized by two modes: 10-20 nm (nucleation particles) and 20-100 nm (Aitken particles). Five dominant industrial sources were identified and used as input for dispersion modelling of PN in 2012. The results showed that in Rotterdam about 70,000 addresses were exposed to an additional annual PNC of 5000-10,000 particles per cm3 and about 55,000 addresses to additional PNC of 10,000-20,000 particles per cm3 for 39% of the time. More measurements of PNC up- and downwind of the industrial area are recommended to identify more accurately the PN emission sources and to validate the dispersion modelling.

  13. Determination of concentration and size distribution of black carbon in submicron aerosol from data of nephelometric measurements of angular scattering coefficients

    NASA Astrophysics Data System (ADS)

    Kozlov, Valerii S.; Rakhimov, Rustam F.; Shmargunov, Vladimir P.

    2015-11-01

    The possibility of determining the Black Carbon (BC) concentration and its size distribution in submicron aerosol from data of polarization spectronephelometric measurements of angular aerosol scattering is demonstrated for the first time. The data of simultaneous nephelometric and aethalometric measurements of BC concentration in wood smoke are compared. The inverse problem is solved from measurements of 40 polarization components of spectral coefficients of angular scattering, and aerosol filling factors and the imaginary part of the complex refractive indexes are determined for subfractions of ultrafine- (radii of 30-100 nm), fine- (100-430 nm), and coarse-disperse (430-770 nm) particles. Then the total BC concentration, its size distribution, and BC fraction are estimated in the approximation of homogeneous volume internal mixture of BC and nonabsorbing matter. The analysis shows that at the long evolution of smoke aerosol, nephelometric and aethalometric estimates of the BC concentrations are in a good agreement. The discrepancy averages about 16% for concentrations varying in a range 30-1000 μg/m3.

  14. Black carbon concentration and deposition estimations in Finland by the regional aerosol-climate model REMO-HAM

    NASA Astrophysics Data System (ADS)

    Hienola, A. I.; Pietikäinen, J.-P.; Jacob, D.; Pozdun, R.; Petäjä, T.; Hyvärinen, A.-P.; Sogacheva, L.; Kerminen, V.-M.; Kulmala, M.; Laaksonen, A.

    2013-04-01

    The prediction skill of the regional aerosol-climate model REMO-HAM was assessed against the black carbon (BC) concentration measurements from five locations in Finland, with focus on Hyytiälä station for the year 2005. We examined to what extent the model is able to reproduce the measurements using several statistical tools: median comparison, overlap coefficient (OVL; the common area under two probability distributions curves) and Z score (a measure of standard deviation, shape and spread of the distributions). The results of the statistics showed that the model is biased low. The local and regional emissions of BC have a significant contribution, and the model tendency to flatten the observed BC is most likely dominated by the lack of domestic burning of biofuel in the emission inventories. A further examination of the precipitation data from both measurements and model showed that there is no correlation between REMO's excessive precipitation and BC underestimation. This suggests that the excessive wet removal is not the main cause of the low black carbon concentration output. In addition, a comparison of wind directions in relation with high black carbon concentrations shows that REMO-HAM is able to predict the BC source directions relatively well. Cumulative black carbon deposition fluxes over Finland were estimated, including the deposition on snow.

  15. Black carbon concentration and deposition estimations in Finland by the regional aerosol-climate model REMO-HAM

    NASA Astrophysics Data System (ADS)

    Hienola, A. I.; Pietikäinen, J.-P.; Jacob, D.; Pozdun, R.; Petäjä, T.; Hyvärinen, A.-P.; Kerminen, V.-M.; Kulmala, M.; Laaksonen, A.

    2012-09-01

    The prediction skill of the regional aerosol-climate model REMO-HAM was assessed against the black carbon (BC) concentration measurements from five locations in Finland, with focus on Hyytiälä station for the year 2005. We examined to what extent the model is able to reproduce the measurements using several statistical tools: median comparison, overlap coefficient OVL (the common area under two probability distributions curves) and Z-score (a measure of standard deviation, shape and spread of the distributions). The results of the statistics showed that the model is biased low, suggesting either an excessive loss of black carbon in the model, or missing emissions. A further examination of the precipitation data from both measurements and model showed that there is no correlation between REMO's excessive precipitation and BC underestimation. This suggests that the excessive wet removal is not the main cause for the low black carbon concentration output. In addition, a comparison of wind directions in relation with high black carbon concentrations shows that REMO-HAM is able to predict the BC source directions relatively well. Cumulative black carbon deposition fluxes over Finland were estimated, including the deposition on snow.

  16. Assessment of an aerosol treatment to improve air quality in a swine concentrated animal feeding operation (CAFO).

    PubMed

    Rule, Ana M; Chapin, Amy R; McCarthy, Sheila A; Gibson, Kristen E; Schwab, Kellogg J; Buckley, Timothy J

    2005-12-15

    Poor air quality within swine concentrated animal feeding operations (CAFOs) poses a threat to workers, the surrounding community, and farm production. Accordingly, the current study was conducted to evaluate a technology for reducing air pollution including particulate matter (PM), viable bacteria, and ammonia within such a facility. The technology consists of an acid-oil-alcohol aerosol applied daily. Its effectiveness was evaluated by comparing air quality from before to after treatment and between treated and untreated sides of a barn separated by an impervious partition. On the untreated side, air quality was typical for a swine CAFO, with mean PM2.5 of 0.28 mg/m3 and PM(TOT) of 1.5 mg/m3. The treatment yielded a reduction in PM concentration of 75-90% from before to after treatment. Effectiveness increased with time, application, and particle size (40% reduction for 1 microm and 90% for >10 microm). Airborne bacteria levels (total bacteria, Enterobacteriaceae, and gram-positive cocci) decreased one logarithmic unit after treatment. In contrast, treatment had no effect on ammonia concentrations. These findings demonstrate the effectiveness of an intervention in yielding exposure and emission reductions. PMID:16475347

  17. Quantitating Changes in Jitter and Spike Number Using Concentric Needle Electrodes in Amyotrophic Lateral Sclerosis Patients

    PubMed Central

    Liu, Ming-Sheng; Niu, Jing-Wen; Li, Yi; Guan, Yu-Zhou; Cui, Li-Ying

    2016-01-01

    Background: Single-fiber electromyography (SFEMG) has been suggested as a quantitative method for supporting chronic partial denervation in amyotrophic lateral sclerosis (ALS) by the revised EI Escorial criteria. Although concentric needle (CN) electrodes have been used to assess jitter in myasthenia gravis patients and healthy controls, there are few reports using CN electrodes to assess motor unit instability and denervation in neurogenic diseases. The aim of this study was to determine whether quantitative changes in jitter and spike number using CN electrodes could be used for ALS studies. Methods: Twenty-seven healthy controls and 23 ALS patients were studied using both CN and single-fiber needle (SFN) electrodes on the extensor digitorum communis muscle with an SFEMG program. The SFN-jitter and SFN-fiber density data were measured using SFN electrodes. The CN-jitter and spike number were measured using CN electrodes. Results: The mean CN-jitter was significantly increased in ALS patients (47.3 ± 17.0 μs) than in healthy controls (27.4 ± 3.3 μs) (P < 0.001). Besides, the mean spike number was significantly increased in ALS patients (2.5 ± 0.5) than in healthy controls (1.7 ± 0.3) (P < 0.001). The sensitivity and specificity in the diagnosis of ALS were 82.6% and 92.6% for CN-jitter (cut-off value: 32 μs), and 91.3% and 96.3% for the spike number (cut-off value: 2.0), respectively. There was no significant difference between the SFN-jitter and CN-jitter in ALS patients; meanwhile, there was no significant difference between the SFN-jitter and CN-jitter in healthy controls. Conclusion: CN-jitter and spike number could be used to quantitatively evaluate changes due to denervation-reinnervation in ALS. PMID:27098787

  18. The variation of nitric acid vapor and nitrate aerosol concentrations near the island of Hawaii

    SciTech Connect

    Lee, G.

    1992-01-01

    Anthropogenic emissions of nitrogen oxides (NO + NO[sub 2]) are estimated to be half of the global emissions to the atmosphere. To understand the effect of increasing anthropogenic reactive nitrogen inputs to the global atmosphere, one needs to monitor their long-term variations. This dissertation examines the variations of total nitrate (nitric acid vapor and nitrate aerosol) at the Mauna Loa Observatory (MLO), Hawaii. During the Mauna Loa Observatory Photochemistry Experiment (MLOPEX) in May, 1988, six different air types were identified at MLO with statistical analysis. They were: (1) volcano influenced air, (2) stratosphere-like air, (3) boundary-layer air with recent anthropogenic influence, (4) photochemical haze, (5) marine boundary-layer air, (6) well-aged and modified marine air. Samples that might be influenced by marine air or human activity from local islands were eliminated with three meterological criteria (wind direction, condensation nuclei, and dew point). To examine the negative sampling artifacts of nitric acid vapor due to ground loss, mixing ratio gradients with height were measured during August of 1991. The observed gradients of nitric acid vapor indicated that the long-term samplers at 8 m at MLO may underestimate the free tropospheric nitric acid vapor mixing ratio by about 20%. The three year mean and median of free tropospheric total nitrate during long-term measurements were 113 pptv and 93 pptv, respectively. Each year, the total nitrate mixing ratios at MLO during the spring and summer were increased by more than a factor of two higher than fall and winter. NO[sub y] from remote continents (Asia and North America) are likely sources of these increased total nitrate at MLO during these seasons. However, other processes govern the total nitrate mixing ratios, e.g., degree of mixing between free tropospheric air and boundary air at source regions, stratospheric injection, and wet removal of total nitrate.

  19. Characteristics of Ambient Black Carbon Mass and Size-Resolved Particle Number Concentrations during Corn Straw Open-Field Burning Episode Observations at a Rural Site in Southern Taiwan

    PubMed Central

    Cheng, Yu-Hsiang; Yang, Li-Sing

    2016-01-01

    Information on the effect of open-field burning of agricultural residues on ambient black carbon (BC) mass and size-resolved particle number concentrations is scarce. In this study, to understand the effect of such open-field burning on short-term air quality, real-time variations of the BC mass and size-resolved particle number concentrations were monitored before and during a corn straw open-field burning episode at a rural site. Correlations between the BC mass and size-resolved particle number concentrations during the episode were investigated. Moreover, the particle number size distribution and absorption Ångström exponent were determined for obtaining the characteristics of aerosol emissions from the corn straw open-field burning. The results can be used to address public health concerns and as a reference for managing similar episodes of open-field burning of agricultural residues. PMID:27399754

  20. Characteristics of Ambient Black Carbon Mass and Size-Resolved Particle Number Concentrations during Corn Straw Open-Field Burning Episode Observations at a Rural Site in Southern Taiwan.

    PubMed

    Cheng, Yu-Hsiang; Yang, Li-Sing

    2016-01-01

    Information on the effect of open-field burning of agricultural residues on ambient black carbon (BC) mass and size-resolved particle number concentrations is scarce. In this study, to understand the effect of such open-field burning on short-term air quality, real-time variations of the BC mass and size-resolved particle number concentrations were monitored before and during a corn straw open-field burning episode at a rural site. Correlations between the BC mass and size-resolved particle number concentrations during the episode were investigated. Moreover, the particle number size distribution and absorption Ångström exponent were determined for obtaining the characteristics of aerosol emissions from the corn straw open-field burning. The results can be used to address public health concerns and as a reference for managing similar episodes of open-field burning of agricultural residues. PMID:27399754

  1. Influences of Ice Crystal Number Concentrations and Habits on Arctic Mixed-Phase Cloud Dynamics

    NASA Astrophysics Data System (ADS)

    Komurcu, Muge

    2015-07-01

    Mixed-phase clouds are frequently present in the Arctic atmosphere, and strongly affect the surface energy budget. In this study, the influences of ice crystal number concentrations and crystal growth habits on the Arctic mixed-phase cloud microphysics and dynamics are investigated for internally and externally driven cloud systems using an eddy-resolving model. Separate simulations are performed with increasing ice concentrations and different ice crystal habits. It is found that the habit influence on cloud microphysics and dynamics is as pronounced as increasing the ice crystal concentrations for internally driven clouds and more dominant for externally driven clouds. Habit influence can lead to a 10 % reduction in surface incident longwave radiation flux. Sensitivity tests are performed to identify the interactions between processes affecting cloud dynamics that allow for persistent clouds (i.e., the radiative cooling at cloud top, ice precipitation stabilization at cloud-base). When cloud-base stabilization influences of ice precipitation are weak, cloud dynamics is more sensitive to radiative cooling. Additional sensitivity simulations are done with increasing surface latent and sensible heat fluxes to identify the influences of external forcing on cloud dynamics. It is found that the magnitude of cloud circulations for an externally driven cloud system with strong precipitation and weak surface fluxes is similar to a weakly precipitating, optically thick, internally driven cloud. For cloud systems with intense ice precipitation obtained through either increasing ice crystal concentrations or assuming ice crystal shapes that grow rapidly and fall fast, the cloud layer may collapse despite the moistening effect of surface fluxes.

  2. Volatility and composition of aerosols in tropical stratosphere and TTL over Biak, Indonesia

    NASA Astrophysics Data System (ADS)

    Hayashi, M.; Shibata, T.; Hara, K.; Hasebe, F.

    2014-12-01

    Number concentration and volatility of aerosols in the Tropical Tropopause Layer (TTL) over Biak (1.2 oS, 136.1 oE) were observed using balloon-borne dual optical particle counters (OPC) in January 2011, 2012, and 2013. One OPC observed number concentration of ambient aerosols and another OPC had an inlet with a thermo denuder, whose temperature were set at 100 to 300 oC, in order to observe volatility. The results suggest that major composition of aerosol change with altitude, from sulfate in upper troposphere to sulfuric acid in stratosphere through TTL region. The ratios of number concentrations of un-volatile aerosol, to those of ambient aerosol in sub-micrometer size range are few percent in stratosphere and several percent in TTL. In addition, un-volatile aerosol concentrations were similar to the concentration of ice particle in sub-visible cirrus.

  3. MAPPING ANNUAL MEAN GROUND-LEVEL PM2.5 CONCENTRATIONS USING MULTIANGLE IMAGING SPECTRORADIOMETER AEROSOL OPTICAL THICKNESS OVER THE CONTIGUOUS UNITED STATES

    EPA Science Inventory

    We present a simple approach to estimating ground-level fine particle (PM2.5, particles smaller than 2.5 um in diameter) concentration using global atmospheric chemistry models and aerosol optical thickness (AOT) measurements from the Multi- angle Imaging SpectroRadiometer (MISR)...

  4. INDOOR/OUTDOOR AEROSOL CONCENTRATION RATIOS DURING THE 1999 FRESNO PARTICULATE MATTER EXPOSURE STUDIES AS A FUNCTION OF SIZE, SEASON, AND TIME OF DAY

    EPA Science Inventory

    The 1999 Fresno particulate matter exposure studies tools place in February (winter season) and April/May (spring season) for two periods of four weeks. During that time, near-continuous measurements of indoor and outdoor aerosol concentrations were made with a scanning mobilit...

  5. Spatial and Temporal Variability of Outdoor Coarse Particulate Matter Mass Concentrations Measured with a New Coarse Particulate Sampler during the Detroit Exposure and Aerosol Research Study

    EPA Science Inventory

    The Detroit Exposure and Aerosol Research Study (DEARS) provided data to compare outdoor residential coarse particulate matter (PM10-2.5) concentrations in six different areas of Detroit with data from a central monitoring site. Daily and seasonal influences on the spa...

  6. Concentration, size-distribution and deposition of mineral aerosol over Chinese desert regions

    NASA Astrophysics Data System (ADS)

    Zhang, Xiao Y.; Arimoto, R.; Zhu, G. H.; Chen, T.; Zhang, G. Y.

    1998-09-01

    The mass-particle size distributions (MSDs) of 9 elements in ground-based aerosol samples from dust storm (DS) and non-dust storm (N-DS) periods were determined for 12 sites in 9 major desert regions in northern China. The masses of the 9 elements (Al, Fe, K, Mg, Mn, Sc, Si, Sr and Ti) in the atmosphere were dominated by local mineral dust that averaged 270μg m-3, and the MSDs for the elements were approximately log-normal. On the basis of Al data, the<10μm particles account for ~84% of the total dust mass over the deserts. Model-calculated ("100-step" method) dry deposition velocities (Vd) for the 9 dust-derived elements during N-DS periods ranged from 4.4 to 6.8cms-1, with a median value of 5.6cms-1. On the basis of a statistical relationship between D99% (the dust particle diameter corresponding to the uppermost 1% of the cumulative mass distribution) and Vd, one can also predict dry velocities, especially when D99% ranges from 30 to 70μm. This provides a simple way to reconstruct Vd for dust deposits (like aeolian loess sediments in the Loess Plateau). The estimated daily dry deposition fluxes were higher during DS vs. N-DS periods, but in most cases, the monthly averaged fluxes were mainly attributable to N-DS dust. Two regions with high dust loading and fluxes are identified: the "Western High-Dust Desert" and the "Northern High-Dust Desert", with Taklimakan Desert and Badain Juran Desert as their respective centers. These are energetic regions in which desert-air is actively exchanged, and these apparently are the major source areas for Asian dust.

  7. Observations of Sub-3 nm Particles and Sulfuric acid Concentrations during Aerosol Life Cycle Intensive Observation Period 2011 in Long Island, New York

    NASA Astrophysics Data System (ADS)

    Yu, H.; Kanawade, V. P.; You, Y.; Hallar, A. G.; Mccubbin, I. B.; Chirokova, G.; Sedlacek, A. J.; Springston, S. R.; Wang, J.; Kuang, C.; Lee, Y.; McGraw, R. L.; Mikkila, J.; Lee, S.

    2012-12-01

    Atmospheric new particle formation (NPF) is an important source of aerosol particles. But the NPF processes are not well understood, in part because of our limited understanding of the formation of atmospheric sub-3 nm size aerosols and the limited number of simultaneous observations of particle size distributions and the aerosol nucleation precursors. During Aerosol Life Cycle Intensive Observation Period (July-August 2011) in Long Island, New York, we deployed a particle size magnifier (Airmodus A09) running at different working fluid saturation ratios and a TSI CPC3776 to extract the information of sub-3 nm particles formation. A scanning mobility particle spectrometer (SMPS), a chemical ionization mass spectrometer (CIMS), and a number of atmospheric trace gas analyzers were used to simultaneously measure aerosol size distributions, sulfuric acid, and other possible aerosol precursors, respectively. Our observation results show that sub-3 nm particles existed during both NPF and non-NPF events, indicating the formation of sub-3nm particle didn't always lead to NPF characterized by typical banana shaped aerosol size distributions measured by SMPS. However, sub-3 nm particles were much higher during NPF events. Sub-3 nm particles were well-correlated with sulfuric acid showing the same diurnal variations and noontime peaks, especially for NPF days. These results are consistent with laboratory studies showing that formation of sub-3 nm particles is very sensitive to sulfuric acid (than amines and ammonia) [Yu et al. GRL 2012]. HYSPLIT back trajectory analysis indicates that air masses from Great Lakes, containing more SO2, VOCs and secondary organics, may contribute to growth of sub-3 nm particles and NPF.

  8. The MODIS Aerosol Algorithm, Products and Validation

    NASA Technical Reports Server (NTRS)

    Remer, L. A.; Kaufman, Y. J.; Tanre, D.; Mattoo, S.; Chu, D. A.; Martins, J. V.; Li, R.-R.; Ichoku, C.; Levy, R. C.; Kleidman, R. G.

    2003-01-01

    The MODerate resolution Imaging Spectroradiometer (MODIS) aboard both NASA's Terra and Aqua satellites is making near global daily observations of the earth in a wide spectral range. These measurements are used to derive spectral aerosol optical thickness and aerosol size parameters over both land and ocean. The aerosol products available over land include aerosol optical thickness at three visible wavelengths, a measure of the fraction of aerosol optical thickness attributed to the fine mode and several derived parameters including reflected spectral solar flux at top of atmosphere. Over ocean, the aerosol optical thickness is provided in seven wavelengths from 0.47 microns to 2.13 microns. In addition, quantitative aerosol size information includes effective radius of the aerosol and quantitative fraction of optical thickness attributed to the fine mode. Spectral aerosol flux, mass concentration and number of cloud condensation nuclei round out the list of available aerosol products over the ocean. The spectral optical thickness and effective radius of the aerosol over the ocean are validated by comparison with two years of AERONET data gleaned from 133 AERONET stations. 8000 MODIS aerosol retrievals colocated with AERONET measurements confirm that one-standard deviation of MODIS optical thickness retrievals fall within the predicted uncertainty of delta tauapproximately equal to plus or minus 0.03 plus or minus 0.05 tau over ocean and delta tay equal to plus or minus 0.05 plus or minus 0.15 tau over land. 271 MODIS aerosol retrievals co-located with AERONET inversions at island and coastal sites suggest that one-standard deviation of MODIS effective radius retrievals falls within delta r_eff approximately equal to 0.11 microns. The accuracy of the MODIS retrievals suggests that the product can be used to help narrow the uncertainties associated with aerosol radiative forcing of global climate.

  9. Occupational Exposure to Cobalt and Tungsten in the Swedish Hard Metal Industry: Air Concentrations of Particle Mass, Number, and Surface Area.

    PubMed

    Klasson, Maria; Bryngelsson, Ing-Liss; Pettersson, Carin; Husby, Bente; Arvidsson, Helena; Westberg, Håkan

    2016-07-01

    . Linear regression analysis of the same data showed statistically significant regression coefficients only for the mass-based aerosol measures. Similar results were seen for rank correlation in the stationary rig, and linear regression analysis implied significant correlation for mass-based and particle surface area measures. The mass-based air concentration levels of cobalt and tungsten in the hard metal plant in our study were low compared to Swedish OELs. Particle number and particle surface area concentrations were in the same order of magnitude as for other industrial settings. Regression analysis implied the use of stationary determined mass-based and particle surface area aerosol concentration as proxies for various exposure measures in our study. PMID:27143598

  10. Occupational Exposure to Cobalt and Tungsten in the Swedish Hard Metal Industry: Air Concentrations of Particle Mass, Number, and Surface Area

    PubMed Central

    Bryngelsson, Ing-Liss; Pettersson, Carin; Husby, Bente; Arvidsson, Helena; Westberg, Håkan

    2016-01-01

    number. Linear regression analysis of the same data showed statistically significant regression coefficients only for the mass-based aerosol measures. Similar results were seen for rank correlation in the stationary rig, and linear regression analysis implied significant correlation for mass-based and particle surface area measures. The mass-based air concentration levels of cobalt and tungsten in the hard metal plant in our study were low compared to Swedish OELs. Particle number and particle surface area concentrations were in the same order of magnitude as for other industrial settings. Regression analysis implied the use of stationary determined mass-based and particle surface area aerosol concentration as proxies for various exposure measures in our study. PMID:27143598

  11. Protection factor for N95 filtering facepiece respirators exposed to laboratory aerosols containing different concentrations of nanoparticles.

    PubMed

    Rengasamy, Samy; Walbert, Gary; Newcomb, William; Coffey, Christopher; Wassell, James Terrence; Szalajda, Jonathan

    2015-04-01

    A previous study used a PortaCount Plus to measure the ratio of particle concentrations outside (C out) to inside (C in) of filtering facepiece respirators (FFRs) worn by test subjects and calculated the total inward leakage (TIL) (C in/C out) to evaluate the reproducibility of the TIL test method between two different National Institute for Occupational Safety and Health laboratories (Laboratories 1 and 2) at the Pittsburgh Campus. The purpose of this study is to utilize the originally obtained PortaCount C out/C in ratio as a measure of protection factor (PF) and evaluate the influence of particle distribution and filter efficiency. PFs were obtained for five N95 model FFRs worn by 35 subjects for three donnings (5 models × 35 subjects × 3 donnings) for a total of 525 tests in each laboratory. The geometric mean of PFs, geometric standard deviation (GSD), and the 5th percentile values for the five N95 FFR models were calculated for the two laboratories. Filter efficiency was obtained by measuring the penetration for four models (A, B, C, and D) against Laboratory 2 aerosol using two condensation particle counters. Particle size distribution, measured using a Scanning Mobility Particle Sizer, showed a mean count median diameter (CMD) of 82 nm in Laboratory 1 and 131 nm in Laboratory 2. The smaller CMD showed relatively higher concentration of nanoparticles in Laboratory 1 than in Laboratory 2. Results showed that the PFs and 5th percentile values for two models (B and E) were larger than other three models (A, C, and D) in both laboratories. The PFs and 5th percentile values of models B and E in Laboratory 1 with a count median diameter (CMD) of 82 nm were smaller than in Laboratory 2 with a CMD of 131 nm, indicating an association between particle size distribution and PF. The three lower efficiency models (A, C, and D) showed lower PF values than the higher efficiency model B showing the influence of filter efficiency on PF value. Overall, the data show that

  12. Protection Factor for N95 Filtering Facepiece Respirators Exposed to Laboratory Aerosols Containing Different Concentrations of Nanoparticles

    PubMed Central

    Rengasamy, Samy; Walbert, Gary; Newcomb, William; Coffey, Christopher; Wassell, James Terrence; Szalajda, Jonathan

    2015-01-01

    A previous study used a PortaCount Plus to measure the ratio of particle concentrations outside (Cout) to inside (Cin) of filtering facepiece respirators (FFRs) worn by test subjects and calculated the total inward leakage (TIL) (Cin/Cout) to evaluate the reproducibility of the TIL test method between two different National Institute for Occupational Safety and Health laboratories (Laboratories 1 and 2) at the Pittsburgh Campus. The purpose of this study is to utilize the originally obtained PortaCount Cout/Cin ratio as a measure of protection factor (PF) and evaluate the influence of particle distribution and filter efficiency. PFs were obtained for five N95 model FFRs worn by 35 subjects for three donnings (5 models × 35 subjects × 3 donnings) for a total of 525 tests in each laboratory. The geometric mean of PFs, geometric standard deviation (GSD), and the 5th percentile values for the five N95 FFR models were calculated for the two laboratories. Filter efficiency was obtained by measuring the penetration for four models (A, B, C, and D) against Laboratory 2 aerosol using two condensation particle counters. Particle size distribution, measured using a Scanning Mobility Particle Sizer, showed a mean count median diameter (CMD) of 82 nm in Laboratory 1 and 131 nm in Laboratory 2. The smaller CMD showed relatively higher concentration of nanoparticles in Laboratory 1 than in Laboratory 2. Results showed that the PFs and 5th percentile values for two models (B and E) were larger than other three models (A, C, and D) in both laboratories. The PFs and 5th percentile values of models B and E in Laboratory 1 with a count median diameter (CMD) of 82 nm were smaller than in Laboratory 2 with a CMD of 131 nm, indicating an association between particle size distribution and PF. The three lower efficiency models (A, C, and D) showed lower PF values than the higher efficiency model B showing the influence of filter efficiency on PF value. Overall, the data show that

  13. ACTRIS ACSM intercomparison - Part 1: Reproducibility of concentration and fragment results from 13 individual Quadrupole Aerosol Chemical Speciation Monitors (Q-ACSM) and consistency with co-located instruments

    NASA Astrophysics Data System (ADS)

    Crenn, V.; Sciare, J.; Croteau, P. L.; Verlhac, S.; Fröhlich, R.; Belis, C. A.; Aas, W.; Äijälä, M.; Alastuey, A.; Artiñano, B.; Baisnée, D.; Bonnaire, N.; Bressi, M.; Canagaratna, M.; Canonaco, F.; Carbone, C.; Cavalli, F.; Coz, E.; Cubison, M. J.; Esser-Gietl, J. K.; Green, D. C.; Gros, V.; Heikkinen, L.; Herrmann, H.; Lunder, C.; Minguillón, M. C.; Močnik, G.; O'Dowd, C. D.; Ovadnevaite, J.; Petit, J.-E.; Petralia, E.; Poulain, L.; Priestman, M.; Riffault, V.; Ripoll, A.; Sarda-Estève, R.; Slowik, J. G.; Setyan, A.; Wiedensohler, A.; Baltensperger, U.; Prévôt, A. S. H.; Jayne, J. T.; Favez, O.

    2015-12-01

    As part of the European ACTRIS project, the first large Quadrupole Aerosol Chemical Speciation Monitor (Q-ACSM) intercomparison study was conducted in the region of Paris for 3 weeks during the late-fall - early-winter period (November-December 2013). The first week was dedicated to the tuning and calibration of each instrument, whereas the second and third were dedicated to side-by-side comparison in ambient conditions with co-located instruments providing independent information on submicron aerosol optical, physical, and chemical properties. Near real-time measurements of the major chemical species (organic matter, sulfate, nitrate, ammonium, and chloride) in the non-refractory submicron aerosols (NR-PM1) were obtained here from 13 Q-ACSM. The results show that these instruments can produce highly comparable and robust measurements of the NR-PM1 total mass and its major components. Taking the median of the 13 Q-ACSM as a reference for this study, strong correlations (r2 > 0.9) were observed systematically for each individual Q-ACSM across all chemical families except for chloride for which three Q-ACSMs showing weak correlations partly due to the very low concentrations during the study. Reproducibility expanded uncertainties of Q-ACSM concentration measurements were determined using appropriate methodologies defined by the International Standard Organization (ISO 17025, 1999) and were found to be 9, 15, 19, 28, and 36 % for NR-PM1, nitrate, organic matter, sulfate, and ammonium, respectively. However, discrepancies were observed in the relative concentrations of the constituent mass fragments for each chemical component. In particular, significant differences were observed for the organic fragment at mass-to-charge ratio 44, which is a key parameter describing the oxidation state of organic aerosol. Following this first major intercomparison exercise of a large number of Q-ACSMs, detailed intercomparison results are presented, along with a discussion of some

  14. A System to Create Stable Nanoparticle Aerosols from Nanopowders.

    PubMed

    Ding, Yaobo; Riediker, Michael

    2016-01-01

    Nanoparticle aerosols released from nanopowders in workplaces are associated with human exposure and health risks. We developed a novel system, requiring minimal amounts of test materials (min. 200 mg), for studying powder aerosolization behavior and aerosol properties. The aerosolization procedure follows the concept of the fluidized-bed process, but occurs in the modified volume of a V-shaped aerosol generator. The airborne particle number concentration is adjustable by controlling the air flow rate. The system supplied stable aerosol generation rates and particle size distributions over long periods (0.5-2 hr and possibly longer), which are important, for example, to study aerosol behavior, but also for toxicological studies. Strict adherence to the operating procedures during the aerosolization experiments ensures the generation of reproducible test results. The critical steps in the standard protocol are the preparation of the material and setup, and the aerosolization operations themselves. The system can be used for experiments requiring stable aerosol concentrations and may also be an alternative method for testing dustiness. The controlled aerosolization made possible with this setup occurs using energy inputs (may be characterized by aerosolization air velocity) that are within the ranges commonly found in occupational environments where nanomaterial powders are handled. This setup and its operating protocol are thus helpful for human exposure and risk assessment. PMID:27501179

  15. Solid aerosol generator

    DOEpatents

    Prescott, D.S.; Schober, R.K.; Beller, J.

    1992-03-17

    An improved solid aerosol generator used to produce a gas borne stream of dry, solid particles of predetermined size and concentration is disclosed. The improved solid aerosol generator nebulizes a feed solution of known concentration with a flow of preheated gas and dries the resultant wet heated aerosol in a grounded, conical heating chamber, achieving high recovery and flow rates. 2 figs.

  16. Improved solid aerosol generator

    DOEpatents

    Prescott, D.S.; Schober, R.K.; Beller, J.

    1988-07-19

    An improved solid aerosol generator used to produce a gas borne stream of dry, solid particles of predetermined size and concentration. The improved solid aerosol generator nebulizes a feed solution of known concentration with a flow of preheated gas and dries the resultant wet heated aerosol in a grounded, conical heating chamber, achieving high recovery and flow rates. 2 figs.

  17. Solid aerosol generator

    DOEpatents

    Prescott, Donald S.; Schober, Robert K.; Beller, John

    1992-01-01

    An improved solid aerosol generator used to produce a gas borne stream of dry, solid particles of predetermined size and concentration. The improved solid aerosol generator nebulizes a feed solution of known concentration with a flow of preheated gas and dries the resultant wet heated aerosol in a grounded, conical heating chamber, achieving high recovery and flow rates.

  18. Understanding Ice Supersaturation, Particle Growth, and Number Concentration in Cirrus Clouds

    NASA Technical Reports Server (NTRS)

    Comstock, Jennifer M.; Lin, Ruei-Fong; Starr, David O'C.; Yang, Ping

    2008-01-01

    Many factors control the ice supersaturation and microphysical properties in cirrus clouds. We explore the effects of dynamic forcing, ice nucleation mechanisms, and ice crystal growth rate on the evolution and distribution of water vapor and cloud properties in nighttime cirrus clouds using a one-dimensional cloud model with bin microphysics and remote sensing measurements obtained at the Department of Energy's Atmospheric Radiation Measurement (ARM) Climate Research Facility located near Lamont, OK. We forced the model using both large-scale vertical ascent and, for the first time, mean mesoscale velocity derived from radar Doppler velocity measurements. Both heterogeneous and homogeneous nucleation processes are explored, where a classical theory heterogeneous scheme is compared with empirical representations. We evaluated model simulations by examining both bulk cloud properties and distributions of measured radar reflectivity, lidar extinction, and water vapor profiles, as well as retrieved cloud microphysical properties. Our results suggest that mesoscale variability is the primary mechanism needed to reproduce observed quantities. Model sensitivity to the ice growth rate is also investigated. The most realistic simulations as compared with observations are forced using mesoscale waves, include fast ice crystal growth, and initiate ice by either homogeneous or heterogeneous nucleation. Simulated ice crystal number concentrations (tens to hundreds particles per liter) are typically two orders of magnitude smaller than previously published results based on aircraft measurements in cirrus clouds, although higher concentrations are possible in isolated pockets within the nucleation zone.

  19. Microphysical processing of aerosol particles in orographic clouds

    NASA Astrophysics Data System (ADS)

    Pousse-Nottelmann, S.; Zubler, E. M.; Lohmann, U.

    2015-08-01

    An explicit and detailed treatment of cloud-borne particles allowing for the consideration of aerosol cycling in clouds has been implemented into COSMO-Model, the regional weather forecast and climate model of the Consortium for Small-scale Modeling (COSMO). The effects of aerosol scavenging, cloud microphysical processing and regeneration upon cloud evaporation on the aerosol population and on subsequent cloud formation are investigated. For this, two-dimensional idealized simulations of moist flow over two bell-shaped mountains were carried out varying the treatment of aerosol scavenging and regeneration processes for a warm-phase and a mixed-phase orographic cloud. The results allowed us to identify different aerosol cycling mechanisms. In the simulated non-precipitating warm-phase cloud, aerosol mass is incorporated into cloud droplets by activation scavenging and released back to the atmosphere upon cloud droplet evaporation. In the mixed-phase cloud, a first cycle comprises cloud droplet activation and evaporation via the Wegener-Bergeron-Findeisen (WBF) process. A second cycle includes below-cloud scavenging by precipitating snow particles and snow sublimation and is connected to the first cycle via the riming process which transfers aerosol mass from cloud droplets to snowflakes. In the simulated mixed-phase cloud, only a negligible part of the total aerosol mass is incorporated into ice crystals. Sedimenting snowflakes reaching the surface remove aerosol mass from the atmosphere. The results show that aerosol processing and regeneration lead to a vertical redistribution of aerosol mass and number. Thereby, the processes impact the total aerosol number and mass and additionally alter the shape of the aerosol size distributions by enhancing the internally mixed/soluble Aitken and accumulation mode and generating coarse-mode particles. Concerning subsequent cloud formation at the second mountain, accounting for aerosol processing and regeneration increases

  20. The relationship between aerosol model uncertainty and radiative forcing uncertainty

    NASA Astrophysics Data System (ADS)

    Carslaw, Ken; Lee, Lindsay; Reddington, Carly

    2016-04-01

    There has been no systematic assessment of how reduction in the uncertainty of global aerosol models will feed through to the uncertainty in the predicted forcing. We use a global model perturbed parameter ensemble to show that tight observational constraint of aerosol concentrations in the model has a relatively small effect on the aerosol-related uncertainty in the calculated aerosol-cloud forcing between pre-industrial and present day periods. One factor is the low sensitivity of present-day aerosol to natural emissions that determine the pre-industrial aerosol state. But the major cause of the weak constraint is that the full uncertainty space of the model generates a large number of model variants that are "equally acceptable" compared to present-day aerosol observations. The narrow range of aerosol concentrations in the observationally constrained model gives the impression of low aerosol model uncertainty, but this hides a range of very different aerosol models. These multiple so-called "equifinal" model variants predict a wide range of forcings. Equifinality in the aerosol model means that tuning of a small number of model processes to achieve model-observation agreement could give a misleading impression of model robustness.

  1. Size segregated mass concentration and size distribution of near surface aerosols over a tropical Indian semi-arid station, Anantapur: Impact of long range transport.

    PubMed

    Raghavendra Kumar, K; Narasimhulu, K; Balakrishnaiah, G; Suresh Kumar Reddy, B; Rama Gopal, K; Reddy, R R; Moorthy, K Krishna; Suresh Babu, S

    2009-10-15

    Regular measurements of size segregated as well as total mass concentration and size distribution of near surface composite aerosols, made using a ten-channel Quartz Crystal Microbalance (QCM) cascade impactor during the period of September 2007-May 2008 are used to study the aerosol characteristics in association with the synoptic meteorology. The total mass concentration varied from 59.70+/-1.48 to 41.40+/-1.72 microg m(-3), out of which accumulation mode dominated by approximately 50%. On a synoptic scale, aerosol mass concentration in the accumulation (submicron) mode gradually increased from an average low value of approximately 26.92+/-1.53 microg m(-3) during the post monsoon season (September-November) to approximately 34.95+/-1.32 microg m(-3) during winter (December-February) and reaching a peak value of approximately 43.56+/-1.42 microg m(-3) during the summer season (March-May). On the contrary, mass concentration of aerosols in the coarse (supermicron) mode increased from approximately 9.23+/-1.25 microg m(-3)during post monsoon season to reach a comparatively high value of approximately 25.89+/-1.95 microg m(-3) during dry winter months and a low value of approximately 8.07+/-0.76 microg m(-3) during the summer season. Effective radius, a parameter important in determining optical (scattering) properties of aerosol size distribution, varied between 0.104+/-0.08 microm and 0.167+/-0.06 microm with a mean value of 0.143+/-0.01 microm. The fine mode is highly reduced during the post monsoon period and the large and coarse modes continue to remain high (replenished) so that their relative dominance increases. It can be seen that among the two parameters measured, correlation of total mass concentration with air temperature is positive (R(2)=0.82) compared with relative humidity (RH) (R(2)=0.75). PMID:19640569

  2. AEROSOL AND GAS MEASUREMENT

    EPA Science Inventory

    Measurements provide fundamental information for evaluating and managing the impact of aerosols on air quality. Specific measurements of aerosol concentration and their physical and chemical properties are required by different users to meet different user-community needs. Befo...

  3. The effect of dry and wet deposition of condensable vapors on secondary organic aerosols concentrations over the continental US

    NASA Astrophysics Data System (ADS)

    Knote, C.; Hodzic, A.; Jimenez, J. L.

    2015-01-01

    The effect of dry and wet deposition of semi-volatile organic compounds (SVOCs) in the gas phase on the concentrations of secondary organic aerosol (SOA) is reassessed using recently derived water solubility information. The water solubility of SVOCs was implemented as a function of their volatility distribution within the WRF-Chem regional chemistry transport model, and simulations were carried out over the continental United States for the year 2010. Results show that including dry and wet removal of gas-phase SVOCs reduces annual average surface concentrations of anthropogenic and biogenic SOA by 48 and 63% respectively over the continental US. Dry deposition of gas-phase SVOCs is found to be more effective than wet deposition in reducing SOA concentrations (-40 vs. -8% for anthropogenics, and -52 vs. -11% for biogenics). Reductions for biogenic SOA are found to be higher due to the higher water solubility of biogenic SVOCs. The majority of the total mass of SVOC + SOA is actually deposited via the gas phase (61% for anthropogenics and 76% for biogenics). Results are sensitive to assumptions made in the dry deposition scheme, but gas-phase deposition of SVOCs remains crucial even under conservative estimates. Considering reactivity of gas-phase SVOCs in the dry deposition scheme was found to be negligible. Further sensitivity studies where we reduce the volatility of organic matter show that consideration of gas-phase SVOC removal still reduces average SOA concentrations by 31% on average. We consider this a lower bound for the effect of gas-phase SVOC removal on SOA concentrations. A saturation effect is observed for Henry's law constants above 108 M atm-1, suggesting an upper bound of reductions in surface level SOA concentrations by 60% through removal of gas-phase SVOCs. Other models that do not consider dry and wet removal of gas-phase SVOCs would hence overestimate SOA concentrations by roughly 50%. Assumptions about the water solubility of SVOCs made in

  4. The effect of dry and wet deposition of condensable vapors on secondary organic aerosols concentrations over the continental US

    DOE PAGESBeta

    Knote, C.; Hodzic, A.; Jimenez, J. L.

    2015-01-06

    The effect of dry and wet deposition of semi-volatile organic compounds (SVOCs) in the gas phase on the concentrations of secondary organic aerosol (SOA) is reassessed using recently derived water solubility information. The water solubility of SVOCs was implemented as a function of their volatility distribution within the WRF-Chem regional chemistry transport model, and simulations were carried out over the continental United States for the year 2010. Results show that including dry and wet removal of gas-phase SVOCs reduces annual average surface concentrations of anthropogenic and biogenic SOA by 48 and 63% respectively over the continental US. Dry deposition ofmore » gas-phase SVOCs is found to be more effective than wet deposition in reducing SOA concentrations (−40 vs. −8% for anthropogenics, and −52 vs. −11% for biogenics). Reductions for biogenic SOA are found to be higher due to the higher water solubility of biogenic SVOCs. The majority of the total mass of SVOC + SOA is actually deposited via the gas phase (61% for anthropogenics and 76% for biogenics). Results are sensitive to assumptions made in the dry deposition scheme, but gas-phase deposition of SVOCs remains crucial even under conservative estimates. Considering reactivity of gas-phase SVOCs in the dry deposition scheme was found to be negligible. Further sensitivity studies where we reduce the volatility of organic matter show that consideration of gas-phase SVOC removal still reduces average SOA concentrations by 31% on average. We consider this a lower bound for the effect of gas-phase SVOC removal on SOA concentrations. A saturation effect is observed for Henry's law constants above 108 M atm−1, suggesting an upper bound of reductions in surface level SOA concentrations by 60% through removal of gas-phase SVOCs. Other models that do not consider dry and wet removal of gas-phase SVOCs would hence overestimate SOA concentrations by roughly 50%. Assumptions about the water solubility

  5. Ground level environmental protein concentrations in various ecuadorian environments: potential uses of aerosolized protein for ecological research

    USGS Publications Warehouse

    Staton, Sarah J.R.; Woodward, Andrea; Castillo, Josemar A.; Swing, Kelly; Hayes, Mark A.

    2014-01-01

    Large quantities of free protein in the environment and other bioaerosols are ubiquitous throughout terrestrial ground level environments and may be integrative indicators of ecosystem status. Samples of ground level bioaerosols were collected from various ecosystems throughout Ecuador, including pristine humid tropical forest (pristine), highly altered secondary humid tropical forest (highly altered), secondary transitional very humid forest (regrowth transitional), and suburban dry montane deforested (suburban deforested). The results explored the sensitivity of localized aerosol protein concentrations to spatial and temporal variations within ecosystems, and their value for assessing environmental change. Ecosystem specific variations in environmental protein concentrations were observed: pristine 0.32 ± 0.09 μg/m3, highly altered 0.07 ± 0.05 μg/m3, regrowth transitional 0.17 ± 0.06 μg/m3, and suburban deforested 0.09 ± 0.04 μg/m3. Additionally, comparisons of intra-environmental differences in seasonal/daily weather (dry season 0.08 ± 0.03 μg/m3 and wet season 0.10 ± 0.04 μg/m3), environmental fragmentation (buffered 0.19 ± 0.06 μg/m3 and edge 0.15 ± 0.06 μg/m3), and sampling height (ground level 0.32 ± 0.09 μg/m3 and 10 m 0.24 ± 0.04 μg/m3) demonstrated the sensitivity of protein concentrations to environmental conditions. Local protein concentrations in altered environments correlated well with satellite-based spectral indices describing vegetation productivity: normalized difference vegetation index (NDVI) (r2 = 0.801), net primary production (NPP) (r2 = 0.827), leaf area index (LAI) (r2 = 0.410). Moreover, protein concentrations distinguished the pristine site, which was not differentiated in spectral indices, potentially due to spectral saturation typical of highly vegetated environments. Bioaerosol concentrations represent an inexpensive method to increase understanding of environmental changes, especially in densely vegetated

  6. Local emission of primary air pollutants and its contribution to wet deposition and concentrations of aerosols and gases in ambient air in Japan

    NASA Astrophysics Data System (ADS)

    Aikawa, Masahide; Hiraki, Takatoshi; Tomoyose, Nobutaka; Ohizumi, Tsuyoshi; Noguchi, Izumi; Murano, Kentaro; Mukai, Hitoshi

    2013-11-01

    We studied wet deposition by precipitation and the concentrations of aerosols and gases in ambient air in relation to the primary air pollutants discharged from domestic areas. The concentrations of aerosols and gases were influenced by nearby emissions except for non-sea-salt SO, which is transported long distances. The area facing the Sea of Japan showed much larger wet deposition than other areas, although the domestic emissions of the primary air pollutants there were small and showed a peak in wet deposition from October to March, as distinct from April to September in other areas. We performed the correlation analyses between wet deposition of each component and the product of the concentrations of corresponding aerosols and gases in ambient air and the two-thirds power of the precipitation. From the results, following scavenging processes were suggested. • Sulfate and ammonium were scavenged in precipitation as particulate matter such as (NH4)2SO4 and NH4HSO4. • Nitrate was scavenged mainly in precipitation through gaseous HNO3. • Ammonium was complementarily scavenged in precipitation through aerosols such as (NH4)2SO4 and NH4HSO4 and through gaseous NH3.

  7. New understanding and quantification of the regime dependence of aerosol-cloud interaction for studying aerosol indirect effects

    NASA Astrophysics Data System (ADS)

    Chen, Jingyi; Liu, Yangang; Zhang, Minghua; Peng, Yiran

    2016-02-01

    Aerosol indirect effects suffer from large uncertainty in climate models and among observations. This study focuses on two plausible factors: regime dependence of aerosol-cloud interactions and the effect of cloud droplet spectral shape. We show, using a new parcel model, that combined consideration of droplet number concentration (Nc) and relative dispersion (ɛ, ratio of standard deviation to mean radius of the cloud droplet size distribution) better characterizes the regime dependence of aerosol-cloud interactions than considering Nc alone. Given updraft velocity (w), ɛ increases with increasing aerosol number concentration (Na) in the aerosol-limited regime, peaks in the transitional regime, and decreases with further increasing Na in the updraft-limited regime. This new finding further reconciles contrasting observations in literature and reinforces the compensating role of dispersion effect. The nonmonotonic behavior of ɛ further quantifies the relationship between the transitional Na and w that separates the aerosol- and updraft-limited regimes.

  8. ACTRIS ACSM intercomparison - Part I: Reproducibility of concentration and fragment results from 13 individual Quadrupole Aerosol Chemical Speciation Monitors (Q-ACSM) and consistency with Time-of-Flight ACSM (ToF-ACSM), High Resolution ToF Aerosol Mass Spectrometer (HR-ToF-AMS) and other co-located instruments

    NASA Astrophysics Data System (ADS)

    Crenn, V.; Sciare, J.; Croteau, P. L.; Verlhac, S.; Fröhlich, R.; Belis, C. A.; Aas, W.; Äijälä, M.; Alastuey, A.; Artiñano, B.; Baisnée, D.; Bonnaire, N.; Bressi, M.; Canagaratna, M.; Canonaco, F.; Carbone, C.; Cavalli, F.; Coz, E.; Cubison, M. J.; Esser-Gietl, J. K.; Green, D. C.; Gros, V.; Heikkinen, L.; Herrmann, H.; Lunder, C.; Minguillón, M. C.; Močnik, G.; O'Dowd, C. D.; Ovadnevaite, J.; Petit, J.-E.; Petralia, E.; Poulain, L.; Priestman, M.; Riffault, V.; Ripoll, A.; Sarda-Estève, R.; Slowik, J. G.; Setyan, A.; Wiedensohler, A.; Baltensperger, U.; Prévôt, A. S. H.; Jayne, J. T.; Favez, O.

    2015-07-01

    As part of the European ACTRIS project, the first large Quadrupole Aerosol Chemical Speciation Monitor (Q-ACSM) intercomparison study was conducted in the region of Paris for three weeks during the late fall-early winter period (November-December 2013). The first week was dedicated to tuning and calibration of each instrument whereas the second and third were dedicated to side-by-side comparison in ambient conditions with co-located instruments providing independent information on submicron aerosol optical, physical and chemical properties. Near real-time measurements of the major chemical species (organic matter, sulfate, nitrate, ammonium and chloride) in the non-refractory submicron aerosols (NR-PM1) were obtained here from 13 Q-ACSM. The results show that these instruments can produce highly comparable and robust measurements of the NR-PM1 total mass and its major components. Taking the median of the 13 Q-ACSM as a reference for this study, strong correlations (r2 > 0.9) were observed systematically for each individual ACSM across all chemical families except for chloride for which three ACSMs showing weak correlations partly due to the very low concentrations during the study. Reproducibility expanded uncertainties of Q-ACSM concentration measurements were determined using appropriate methodologies defined by the International Standard Organization (ISO 17025) and were found to be of 9, 15, 19, 28 and 36 % for NR-PM1, nitrate, organic matter, sulfate and ammonium respectively. However, discrepancies were observed in the relative concentrations of the constituent mass fragments for each chemical component. In particular, significant differences were observed for the organic fragment at mass-to-charge ratio 44, which is a key parameter describing the oxidation state of organic aerosol. Following this first major intercomparison exercise of a large number of ACSMs, detailed intercomparison results are presented as well as a discussion of some recommendations

  9. Comparison of Bulk Carbon Concentrations and Optical Properties of Carbonaceous Aerosols in the North Slope Alaska from Summer 2012 and Summer 2015

    NASA Astrophysics Data System (ADS)

    Sheesley, R. J.; Barrett, T. E.; Moffett, C.; Gunsch, M.; Pratt, K.

    2015-12-01

    With recent drilling permits being issued for exploratory drilling in the Chukchi Sea, there is a need for characterization of carbonaceous aerosols in the Arctic both prior to and during the exploratory drilling phase. A month-long field sampling campaign will be conducted in Barrow, AK, at the confluence of the Chukchi and Beaufort seas, from August to September 2015. Total suspended particulate (TSP) aerosol samples will be collected at the Department of Energy Atmospheric Radiation Measurement (ARM) climate research facility in Barrow, AK, USA. Samples will be analyzed for organic carbon (OC), elemental carbon (EC) on a Sunset carbon analyzer utilizing the NIOSH 5040 method. Samples will also be analyzed for water soluble organic carbon (WSOC) using a water extraction method and subsequent analysis on a Shimadzu Total Carbon Analyzer. Optical properties of the aqueous extracts will also be measured using an Agilent ultraviolet-visible (UV-Vis) spectrometer. OC, EC and WSOC concentrations will then be compared to aerosol samples collected at the same location in summer 2012, prior to the onset of exploratory drilling in the Chukchi Sea. Back trajectory (BT) analysis will be performed for each sampling campaign to help assess the impact of source region on the carbonaceous aerosol budget and to identify any changes in source region between the two campaigns. A comparison of samples from the same location and season both prior to and post drilling will allow for a more accurate characterization and tracking of the potential impacts of new aerosol emission sources in the region.

  10. Aerosol species concentrations and source apportionment of ammonia at Rocky Mountain National Park.

    PubMed

    Malm, William C; Schichtel, Bret A; Barna, Michael G; Gebhart, Kristi A; Rodriguez, Marco A; Collett, Jeffrey L; Carrico, Christian M; Benedict, Katherine B; Prenni, Anthony J; Kreidenweis, Sonia M

    2013-11-01

    Changes in ecosystem function at Rocky Mountain National Park (RMNP) are occurring because of emissions of nitrogen and sulfate species along the Front Range of the Colorado Rocky Mountains, as well as sources farther east and west. The nitrogen compounds include both oxidized and reduced nitrogen. A year-long monitoring program of various oxidized and reduced nitrogen species was initiated to better understand their origins as well as the complex chemistry occurring during transport from source to receptor. Specifically the goals of the study were to characterize the atmospheric concentrations of nitrogen species in gaseous, particulate, and aqueous phases (precipitation and clouds) along the east and west sides of the Continental Divide; identify the relative contributions to atmospheric nitrogen species in RMNP from within and outside of the state of Colorado; identify the relative contributions to atmospheric nitrogen species in RMNP from emission sources along the Colorado Front Range versus other areas within Colorado; and identify the relative contributions to atmospheric nitrogen species from mobile sources, agricultural activities, and large and small point sources within the state of Colorado. Measured ammonia concentrations are combined with modeled releases of conservative tracers from ammonia source regions around the United States to apportion ammonia to its respective sources, using receptor modeling tools. PMID:24344569

  11. Experimental Challenges and Successes in Measuring Aerosol Concentrations at Prototypic Spray Conditions Encountered at the Hanford Waste Treatment and Immobilization Plant - 13327

    SciTech Connect

    Bontha, J.R.; Gauglitz, P.A.; Kurath, D.E.; Adkins, H.E.; Enderlin, C.W.; Blanchard, J.; Daniel, R.C.; Song, C.; Schonewill, P.P.; Mahoney, L.A.; Buchmiller, W.C.; Boeringa, G.; Jenks, J.

    2013-07-01

    To date, majority of the work done on measuring aerosol releases from failure of process piping was done using simple Newtonian fluids and small engineered-nozzles that do not accurately represent the fluids and breaches postulated during accident analysis at the Hanford Waste Treatment and Immobilization Plant (WTP). In addition, the majority of the work conducted in this area relies on in-spray measurements that neglect the effect of splatter and do not yield any information regarding aerosol generation rates from this additional mechanism. In order to estimate aerosol generation rates as well as reduce the uncertainties in estimating the aerosol release fractions over a broad range of breaches, fluid properties and operating conditions encountered at the WTP, the Pacific Northwest National Laboratory (PNNL) has designed, commissioned, and tested two experimental test stands. The first test stand, referred to as the large-scale test stand, was designed specifically to measure aerosol concentrations and release fractions under prototypic conditions of flow and pressure for a range of breaches postulated in the hazard analysis for 0.076 m (3-inch) process pipes. However, the size of the large-scale test stand, anticipated fluid loss during a breach, experimental risks, and costs associated with hazardous chemical simulant testing limited the large-scale test stand utility to water and a few non-hazardous physical simulants that did not fully span the particle size and rheological properties of the fluids encountered at the WTP. Overcoming these limitations and extending the range of simulants used, required designing and building a smaller test stand, which was installed and operated in a fume hood. This paper presents some of the features of both test stands, the experimental challenges encountered, and successes in measuring aerosol concentration in both test stands over a range of test conditions. (authors)

  12. Stratospheric aerosols and climatic change

    NASA Technical Reports Server (NTRS)

    Baldwin, B.; Pollack, J. B.; Summers, A.; Toon, O. B.; Sagan, C.; Van Camp, W.

    1976-01-01

    Generated primarily by volcanic explosions, a layer of submicron silicate particles and particles made of concentrated sulfuric acids solution is present in the stratosphere. Flights through the stratosphere may be a future source of stratospheric aerosols, since the effluent from supersonic transports contains sulfurous gases (which will be converted to H2SO4) while the exhaust from Space Shuttles contains tiny aluminum oxide particles. Global heat balance calculations have shown that the stratospheric aerosols have made important contributions to some climatic changes. In the present paper, accurate radiative transfer calculations of the globally-averaged surface temperature (T) are carried out to estimate the sensitivity of the climate to changes in the number of stratospheric aerosols. The results obtained for a specified model atmosphere, including a vertical profile of the aerosols, indicate that the climate is unlikely to be affected by supersonic transports and Space Shuttles, during the next decades.

  13. Submicron aerosol size distributions and cloud condensation nuclei concentrations measured at Gosan, Korea, during the Atmospheric Brown Clouds-East Asian Regional Experiment 2005

    NASA Astrophysics Data System (ADS)

    Yum, Seong Soo; Roberts, Greg; Kim, Jong Hwan; Song, Keunyong; Kim, Dohyeong

    2007-11-01

    Submicron aerosol size distributions, CN and CCN concentrations at a constant supersaturation of 0.6% were measured at a relatively remote coastal site at Gosan in Jeju Island, Korea, during the ABC-EAREX from 11 March to 8 April 2005. The average CN concentrations were 6088 ± 3988, 5231 ± 2454 and 3513 ± 1790 cm-3, respectively, for the three major air mass types classified by their origins. The corresponding CCN concentrations were 2393 ± 1156, 2897 ± 1226 and 1843 ± 585 cm-3. The type III air mass was the closest to maritime origins, but these lowest concentrations at Gosan were an order of magnitude higher than those of clean marine boundary layer, indicating that regardless of air mass designation springtime submicron aerosols at Gosan were under steady continental influences. Distinct new particle formation and growth events occurred on 6 d, when clear sky weather conditions prevailed that brought air from northern China, Mongolia or Russia by anticyclonic circulations. Simultaneous occurrence of these events at a western coastal site in the Korean Peninsula 350 km north of Gosan suggests that these events were not local but at least regional-scale events. CCN concentrations were predicted with the aerosol size distributions and the assumption of particles being composed of (NH4)2SO4. The predicted to measured CCN concentration ratio was 1.27 ± 0.29 and the r2 was 0.77 for the whole measurement period. The type I air mass that has the most continental influences showed a slight tendency to overpredict CCN concentrations but the good agreement overall suggests that springtime Gosan aerosols act almost like ammonium sulfate as far as CCN activity is concerned, almost regardless of air mass origin.

  14. Spatial and temporal variation of particle number concentration in Augsburg, Germany

    PubMed Central

    Cyrys, Josef; Pitz, Mike; Heinrich, Joachim; Wichmann, H.-Erich; Peters, Annette

    2008-01-01

    Epidemiological studies on health effects of outdoor air pollution are largely based on single monitoring site for estimating the exposure of people living in urban areas. For such an approach two aspects are important: the temporal correlation and the spatial variation of the absolute levels of concentrations measured at different sites in an urban area. Whereas many studies have shown small spatial variability of fine particles in urban areas, little is known on how well a single monitoring station could represent the temporal and spatial variation of ultrafine particles across urban areas. In our study we investigated the temporal and spatial variation of particle number concentration (PNC) at four background sites in Augsburg, Germany. Two of them were influenced by traffic, one was placed in the outskirts of the city. The average PNC levels at two urban background sites with traffic impact were 16,943 cm−3 and 20,702 cm−3, respectively, compared to 11,656 cm−3 at the urban background site without traffic impact (ratio 1.2 to 1.8). The Spearman correlation coefficients between the monitoring sites were high (r>0.80). The pronounced differences in absolute PNC levels suggest that the use of a single monitoring station in long-term epidemiological studies must be insufficient to attribute accurate exposure levels of PNC to all study subjects. On the other hand, the high temporal correlations of PNC across the city area of Augsburg implicate that in epidemiological time-series studies the use of one single ambient monitoring site is an adequate approach for characterizing exposure to ultrafine particles. PMID:18511107

  15. Evaluation of quantum dot cytotoxicity: interpretation of nanoparticle concentrations versus intracellular nanoparticle numbers.

    PubMed

    Manshian, Bella B; Abdelmonem, Abuelmagd M; Kantner, Karsten; Pelaz, Beatriz; Klapper, Markus; Nardi Tironi, Catarina; Parak, Wolfgang J; Himmelreich, Uwe; Soenen, Stefaan J

    2016-11-01

    While substantial progress has been achieved in the design of more biocompatible nanoparticles (NP), detailed data are required on the precise interactions of NPs and their environment for more reliable interpretation of toxicity results. Therefore, this study aims to investigate the interaction of two quantum dots (QDs) of the same core material CdSe/ZnS coated with two different amphiphilic polymers, with two well-established mammalian cell lines representing possible sites of QD accumulation. Results are linked to either extracellular QD concentrations (given dose) or cellular QD levels (number of internalized particles). In this study, QD internalization, effects on cellular homeostasis, and consequent inflammatory and cytoskeletal alterations caused by these QDs were explored. Fluorescence imaging techniques, including; image-based flow cytometry, confocal microscopy and high-content imaging with the InCell analyzer were used in a multiparametric methodology to evaluate cell viability, induction of oxidative stress, mitochondrial health, cell cytoskeletal functionality and changes in cellular morphology. Gene expression arrays were also carried out on 168 key genes involved in the cytoskeletal architecture and inflammatory pathway accompanied with the analysis of focal adhesions as key markers for actin-mediated signaling. Our results show distinct differences between the PMA and PTMAEMA-stat-PLMA coated QDs, which could mainly be attributed to differences in their cellular uptake levels. The toxicity profiles of both QD types changed drastically depending on whether effects were expressed in terms of given dose or internalized particles. Both QDs triggered alterations to important but different genes, most remarkably the up-regulation of tumor suppression and necrosis genes and the down regulation of angiogenesis and metastasis genes at sub-cytotoxic concentrations of these QDs. PMID:27416974

  16. High concentrations of biological aerosol particles and ice nuclei during and after rain

    NASA Astrophysics Data System (ADS)

    Huffman, J. Alex; Pöhlker, Christopher; Prenni, Anthony; DeMott, Paul; Mason, Ryan; Robinson, Niall; Fröhlich-Nowoisky, Janine; Tobo, Yutaka; Després, Viviane; Garcia, Elvin; Gochis, David; Sinha, Bärbel; Day, Douglas; Andreae, Meinrat; Jimenez, Jose; Gallagher, Martin; Kreidenweis, Sonia; Bertram, Allan; Pöschl, Ulrich

    2013-04-01

    Bioaerosols are relevant for public health and may play an important role in the climate system, but their atmospheric abundance, properties and sources are not well understood. Here we show that the concentration of airborne biological particles in a forest ecosystem increases dramatically during rain and that bioparticles are closely correlated with atmospheric ice nuclei (IN). The greatest increase of bioparticles and IN occurred in the size range of 2-6 µm, which is characteristic for bacterial aggregates and fungal spores. By DNA analysis we found high diversities of airborne bacteria and fungi, including human and plant pathogens (mildew, smut and rust fungi, molds, Enterobacteraceae, Pseudomonadaceae). In addition to known bacterial and fungal IN (Pseudomonas sp., Fusarium sporotrichioides), we discovered two species of IN-active fungi that were not previously known as biological ice nucleators (Isaria farinosa and Acremonium implicatum). Our findings suggest that atmospheric bioaerosols, IN and rainfall are more tightly coupled than previously assumed.

  17. High concentrations of biological aerosol particles and ice nuclei during and after rain

    NASA Astrophysics Data System (ADS)

    Huffman, J. A.; Pöhlker, C.; Prenni, A. J.; DeMott, P. J.; Mason, R. H.; Robinson, N. H.; Fröhlich-Nowoisky, J.; Tobo, Y.; Després, V. R.; Garcia, E.; Gochis, D. J.; Harris, E.; Müller-Germann, I.; Ruzene, C.; Schmer, B.; Sinha, B.; Day, D. A.; Andreae, M. O.; Jimenez, J. L.; Gallagher, M.; Kreidenweis, S. M.; Bertram, A. K.; Pöschl, U.

    2013-01-01

    Bioaerosols are relevant for public health and may play an important role in the climate system, but their atmospheric abundance, properties and sources are not well understood. Here we show that the concentration of airborne biological particles in a forest ecosystem increases dramatically during rain and that bioparticles are closely correlated with atmospheric ice nuclei (IN). The greatest increase of bioparticles and IN occurred in the size range of 2-6 μm, which is characteristic for bacterial aggregates and fungal spores. By DNA analysis we found high diversities of airborne bacteria and fungi, including human and plant pathogens (mildew, smut and rust fungi, molds, Enterobacteraceae, Pseudomonadaceae). In addition to known bacterial and fungal IN (Pseudomonas sp., Fusarium sporotrichioides), we discovered two species of IN-active fungi that were not previously known as biological ice nucleators (Isaria farinosa and Acremonium implicatum). Our findings suggest that atmospheric bioaerosols, IN and rainfall are more tightly coupled than previously assumed.

  18. Linking particle number concentration (PNC), meteorology and traffic variables in a UK street canyon

    NASA Astrophysics Data System (ADS)

    Price, Heather D.; Arthur, Robert; BéruBé, Kelly A.; Jones, Tim P.

    2014-10-01

    Ambient particle number concentration (PNC) has been linked with adverse health outcomes such as asthma, reduced lung function and cardiovascular disease. To investigate the relationship between PNC, meteorology and traffic we measured size segregated respirable particles in a busy commuter street in Swansea, UK for ten months using a Dekati Electrical Low Pressure Impactor (ELPI). The ELPI segregates particles into 12 size fractions between 7 nm and 10 μm. The median PNC for the sampling period was 31,545 cm- 3. For the ultrafine particles (7-93 nm), the highest PNC was found in winter (46,615 cm- 3; 15 minute average) and the lowest for that size fraction in summer (29,696 cm- 3). For the particles below 93 nm there was a trimodal distribution to weekdays (particularly Monday to Wednesday), with PNC peaks at 09:00, 16:00 and 23:00. Wind direction had a significant influence on PNC and differed between particles in the fine range (below 2.5 μm) and more coarse particles (up to 10 μm). For fine particles, winds parallel to the canyon were associated with higher PNCs which were attributed to the replenishment of traffic particles. For coarse particles, PNCs were higher from winds perpendicular to the canyon and this was linked to source distribution around the sampling site and the recirculation of pollutants within the canyon. During times when vehicle volumes were high and vehicles were exhibiting stop-start behaviour, if this was combined with low wind speeds, ultrafine PNC was highest. This effect was generally observed during the morning rush hour. Current mass-based legislation does not take into account exposure to the number of particles or the change in population exposure diurnally.

  19. Understanding Ice Supersaturation, Particle Growth, and Number Concentration in Cirrus Clouds

    SciTech Connect

    Comstock, Jennifer M.; Lin, Ruei-Fong; Starr, David O.; Yang, P.

    2008-12-10

    Many factors control the ice supersaturation and microphysical properties in cirrus clouds. We explore the effects of dynamic forcing, ice nucleation mechanisms, and ice crystal growth rate on the evolution and distribution of water vapor and cloud properties in cirrus clouds using a detailed microphysical model and remote sensing measurements obtained at the Department of Energy’s Atmospheric Radiation Measurement (ARM) Climate Research Facility located near Lamont, OK. To help understand dynamic scales important in cirrus formation, we force the model using both large-scale forcing derived using ARM variational analysis, and mean mesoscale velocity derived from radar Doppler velocity measurements. Both heterogeneous and homogeneous nucleation processes are explored, where we have implemented a rigorous classical theory heterogeneous nucleation scheme to compare with empirical representations. We evaluate model simulations by examining both bulk cloud properties and distributions of measured radar reflectivity, lidar extinction, and water vapor profiles, as well as retrieved cloud microphysical properties. This approach allows for independent verification of both the large and small particle modes of the particle size distribution. Our results suggest that mesoscale variability is the primary mechanism needed to reproduce observed quantities, while nucleation mechanism is secondary. Slow ice crystal growth tends to overestimate the number of small ice crystals, but does not seem to influence bulk properties such as ice water path and cloud thickness. The most realistic simulations as compared with observations are forced using mesoscale waves, include fast ice crystal growth, and initiate ice by either homogeneous or heterogeneous nucleation. Ice crystal number concentrations on the order of 10-100 L-1 produce results consistent with both lidar and radar observations during a cirrus event observed on 7 December 1999, which has an optical depth range typical of

  20. Turbulent Size Selection and Concentration of Chondrule-Sized Objects: Reynolds Number Invariance and Implications

    NASA Technical Reports Server (NTRS)

    Cuzzi, J. N.; Hogan, R.; Dobrovolskis, A.; Paque, J.

    2006-01-01

    size depends primarily on the intensity of the turbulent kinetic energy (represented by the Reynolds number of the nebula). Specifically, the preferentially concentrated particle is that which has a stopping time equal to the turnover time of the smallest eddy. The intensity level of turbulence implied by chondrule sizes can be maintained by even a small fraction of the energy released by the radially evolving disk (it must be noted that the details of how this transfer of energy actually occurs remain obscure, however).

  1. Optimized sparse-particle aerosol representations for modeling cloud-aerosol interactions

    NASA Astrophysics Data System (ADS)

    Fierce, Laura; McGraw, Robert

    2016-04-01

    Sparse representations of atmospheric aerosols are needed for efficient regional- and global-scale chemical transport models. Here we introduce a new framework for representing aerosol distributions, based on the method of moments. Given a set of moment constraints, we show how linear programming can be used to identify collections of sparse particles that approximately maximize distributional entropy. The collections of sparse particles derived from this approach reproduce CCN activity of the exact model aerosol distributions with high accuracy. Additionally, the linear programming techniques described in this study can be used to bound key aerosol properties, such as the number concentration of CCN. Unlike the commonly used sparse representations, such as modal and sectional schemes, the maximum-entropy moment-based approach is not constrained to pre-determined size bins or assumed distribution shapes. This study is a first step toward a new aerosol simulation scheme that will track multivariate aerosol distributions with sufficient computational efficiency for large-scale simulations.

  2. Variability of Surface pollutants and aerosol concentration over Abu Dhabi, UAE - sources, transport and current levels

    NASA Astrophysics Data System (ADS)

    Phanikumar, Devulapalli V.; Basha, Ghouse; Ouarda, Taha B. M. J.

    2015-04-01

    In the view of recent economic, industrial, and rapid development, Abu Dhabi (24.4oN; 54.4oE; 27m msl) has become one of the most populated regions in the world despite of extreme heat, frequent dust storms, and with distinctive topography. The major sources of air pollution are from the dust and sand storms, greenhouse gas emissions, and to some extent from industrial pollution. In order to realize the accurate and comprehensive understanding of air quality and plausible sources over this region, we have made a detailed analysis of three years simultaneous measurements during 2011-13 of pollutants such as O3, SO2, NO2, CO, and PM10 concentrations. Diurnal variation of meteorological parameters such as temperature and wind speed/relative humidity clearly shows daytime maximum/minimum in summer followed by pre-monsoon, post-monsoon and winter. The prevailing winds over this region are mostly from northwesterly direction (Shamal wind). Diurnal wind pattern showed a clear contrast with the majority of the wind pattern during nighttime and early morning is from the westerly/northwesterly and daytime is from southwesterly/southeasterly directions. The diurnal pattern of O3 shows minimum during 08 LT and increases thereafter reaching maximum at 17 LT and decreases during nighttime. However, the diurnal pattern of SO2 and NO2 show a peak at ~ 08 LT and dip at ~ 14 LT during all the seasons with some variability in each season. On the other hand, the diurnal pattern of CO shows a peculiar picture of elevated levels during daytime peaking at ~ 10 LT (prominent in summer and post-monsoon) followed by a sharp decrease and minimum is ~14 LT. PM10 concentration has an early morning peak at ~ 02 LT and then decreases to a minimum value at ~11 LT and again increases in the afternoon hours (maximum at ~17 LT) depicting a forenoon-afternoon asymmetry. Monthly variation of PM10 shows maximum in pre-monsoon season and minimum in winter. Our observations show the diurnal pattern of

  3. Dynamics and rheology of concentrated, finite-Reynolds-number suspensions in a homogeneous shear flow

    NASA Astrophysics Data System (ADS)

    Yeo, Kyongmin; Maxey, Martin R.

    2013-05-01

    We present the lubrication-corrected force-coupling method for the simulation of concentrated suspensions under finite inertia. Suspension dynamics are investigated as a function of the particle-scale Reynolds number Re_{dot{γ }} and the bulk volume fraction ϕ in a homogeneous linear shear flow, in which Re_{dot{γ }} is defined from the density ρf and dynamic viscosity μ of the fluid, particle radius a, and the shear rate dot{γ } as Re_{dot{γ }}= ρ _f dot{γ } a^2 / μ. It is shown that the velocity fluctuations in the velocity-gradient and vorticity directions decrease at larger Re_{dot{γ }}. However, the particle self-diffusivity is found to be an increasing function of Re_{dot{γ }} as the motion of the suspended particles develops a longer auto-correlation under finite fluid inertia. It is shown that finite-inertia suspension flows are shear-thickening and the particle stresses become highly intermittent as Re_{dot{γ }} increases. To study the detailed changes in the suspension microstructure and rheology, we introduce a particle-stress-weighted pair-distribution function. The stress-weighted pair-distribution function clearly shows that the increase of the effective viscosity at high Re_{dot{γ }} is mostly related to the strong normal lubrication interaction in the compressive principal axis of the shear flow.

  4. Origin of high particle number concentrations reaching the St. Louis, Midwest Supersite.

    PubMed

    de Foy, Benjamin; Schauer, James J

    2015-08-01

    Ultrafine particles are associated with adverse health effects. Total Particle Number Concentration (TNC) of fine particles were measured during 2002 at the St. Louis - Midwest supersite. The time series showed overall low level with frequent large peaks. The time series was analyzed alongside criteria pollutant measurements and meteorological observations. Multiple regression analysis was used to identify further contributing factors and to determine the association of different pollutants with TNC levels. This showed the strong contribution of sulfur dioxide (SO2) and nitrogen oxides (NOx) to high TNC levels. The analysis also suggested that increased dispersion resulting from faster winds and higher mixing heights led to higher TNC levels. Overall, the results show that there were intense particle nucleation events in a SO2 rich plume reaching the site which contributed around 29% of TNC. A further 40% was associated with primary emissions from mobile sources. By separating the remaining TNC by time of day and clear sky conditions, we suggest that most likely 8% of TNC are due to regional nucleation events and 23% are associated with the general urban background. PMID:26257365

  5. Hourly elemental concentrations in PM2.5 aerosols sampled simultaneously at urban background and road site during SAPUSS - diurnal variations and PMF receptor modelling

    NASA Astrophysics Data System (ADS)

    Dall'Osto, M.; Querol, X.; Amato, F.; Karanasiou, A.; Lucarelli, F.; Nava, S.; Calzolai, G.; Chiari, M.

    2013-04-01

    Hourly-resolved aerosol chemical speciation data can be a highly powerful tool to determine the source origin of atmospheric pollutants in urban environments. Aerosol mass concentrations of seventeen elements (Na, Mg, Al, S, Cl, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Sr and Pb) were obtained by time (1 h) and size (PM2.5 particulate matter < 2.5 μm) resolved aerosol samples analysed by Particle Induced X-ray Emission (PIXE) measurements. In the Marie Curie European Union framework of SAPUSS (Solving Aerosol Problems by Using Synergistic Strategies), the approach used is the simultaneous sampling at two monitoring sites in Barcelona (Spain) during September-October 2010: an urban background site (UB) and a street canyon traffic road site (RS). Elements related to primary non-exhaust traffic emission (Fe, Cu), dust resuspension (Ca) and anthropogenic Cl were found enhanced at the RS, whereas industrial related trace metals (Zn, Pb, Mn) were found at higher concentrations at the more ventilated UB site. When receptor modelling was performed with positive matrix factorization (PMF), nine different aerosol sources were identified at both sites: three types of regional aerosols (regional sulphate (S) - 27%, biomass burning (K) - 5%, sea salt (Na-Mg) - 17%), three types of dust aerosols (soil dust (Al-Ti) - 17%, urban crustal dust (Ca) - 6%, and primary traffic non-exhaust brake dust (Fe-Cu) - 7%), and three types of industrial aerosol plumes-like events (shipping oil combustion (V-Ni) - 17%, industrial smelters (Zn-Mn) - 3%, and industrial combustion (Pb-Cl) - 5%, percentages presented are average source contributions to the total elemental mass measured). The validity of the PMF solution of the PIXE data is supported by very good correlations with external single particle mass spectrometry measurements. Some important conclusions can be drawn about the PM2.5 mass fraction simultaneously measured at the UB and RS sites: (1) the regional aerosol sources impact both

  6. High concentrations of biological aerosol particles and ice nuclei during and after rain

    NASA Astrophysics Data System (ADS)

    Huffman, J. A.; Prenni, A. J.; DeMott, P. J.; Pöhlker, C.; Mason, R. H.; Robinson, N. H.; Fröhlich-Nowoisky, J.; Tobo, Y.; Després, V. R.; Garcia, E.; Gochis, D. J.; Harris, E.; Müller-Germann, I.; Ruzene, C.; Schmer, B.; Sinha, B.; Day, D. A.; Andreae, M. O.; Jimenez, J. L.; Gallagher, M.; Kreidenweis, S. M.; Bertram, A. K.; Pöschl, U.

    2013-07-01

    Bioaerosols are relevant for public health and may play an important role in the climate system, but their atmospheric abundance, properties, and sources are not well understood. Here we show that the concentration of airborne biological particles in a North American forest ecosystem increases significantly during rain and that bioparticles are closely correlated with atmospheric ice nuclei (IN). The greatest increase of bioparticles and IN occurred in the size range of 2-6 μm, which is characteristic for bacterial aggregates and fungal spores. By DNA analysis we found high diversities of airborne bacteria and fungi, including groups containing human and plant pathogens (mildew, smut and rust fungi, molds, Enterobacteriaceae, Pseudomonadaceae). In addition to detecting known bacterial and fungal IN (Pseudomonas sp., Fusarium sporotrichioides), we discovered two species of IN-active fungi that were not previously known as biological ice nucleators (Isaria farinosa and Acremonium implicatum). Our findings suggest that atmospheric bioaerosols, IN, and rainfall are more tightly coupled than previously assumed.

  7. Comparison of MADE3-simulated and observed aerosol distributions with a focus on aerosol vertical profiles

    NASA Astrophysics Data System (ADS)

    Kaiser, Christopher; Hendricks, Johannes; Righi, Mattia; Jöckel, Patrick

    2016-04-01

    The reliability of aerosol radiative forcing estimates from climate models depends on the accuracy of simulated global aerosol distribution and composition, as well as on the models' representation of the aerosol-cloud and aerosol-radiation interactions. To help improve on previous modeling studies, we recently developed the new aerosol microphysics submodel MADE3 that explicitly tracks particle mixing state in the Aitken, accumulation, and coarse mode size ranges. We implemented MADE3 into the global atmospheric chemistry general circulation model EMAC and evaluated it by comparison of simulated aerosol properties to observations. Compared properties include continental near-surface aerosol component concentrations and size distributions, continental and marine aerosol vertical profiles, and nearly global aerosol optical depth. Recent studies have shown the specific importance of aerosol vertical profiles for determination of the aerosol radiative forcing. Therefore, our focus here is on the evaluation of simulated vertical profiles. The observational data is taken from campaigns between 1990 and 2011 over the Pacific Ocean, over North and South America, and over Europe. The datasets include black carbon and total aerosol mass mixing ratios, as well as aerosol particle number concentrations. Compared to other models, EMAC with MADE3 yields good agreement with the observations - despite a general high bias of the simulated mass mixing ratio profiles. However, BC concentrations are generally overestimated by many models in the upper troposphere. With MADE3 in EMAC, we find better agreement of the simulated BC profiles with HIPPO data than the multi-model average of the models that took part in the AeroCom project. There is an interesting difference between the profiles from individual campaigns and more "climatological" datasets. For instance, compared to spatially and temporally localized campaigns, the model simulates a more continuous decline in both total

  8. Impact of aerosol size representation on modeling aerosol-cloud interactions

    SciTech Connect

    Zhang, Y.; Easter, R. C.; Ghan, S. J.; Abdul-Razzak, H.

    2002-11-07

    In this study, we use a 1-D version of a climate-aerosol-chemistry model with both modal and sectional aerosol size representations to evaluate the impact of aerosol size representation on modeling aerosol-cloud interactions in shallow stratiform clouds observed during the 2nd Aerosol Characterization Experiment. Both the modal (with prognostic aerosol number and mass or prognostic aerosol number, surface area and mass, referred to as the Modal-NM and Modal-NSM) and the sectional approaches (with 12 and 36 sections) predict total number and mass for interstitial and activated particles that are generally within several percent of references from a high resolution 108-section approach. The modal approach with prognostic aerosol mass but diagnostic number (referred to as the Modal-M) cannot accurately predict the total particle number and surface areas, with deviations from the references ranging from 7-161%. The particle size distributions are sensitive to size representations, with normalized absolute differences of up to 12% and 37% for the 36- and 12-section approaches, and 30%, 39%, and 179% for the Modal-NSM, Modal-NM, and Modal-M, respectively. For the Modal-NSM and Modal-NM, differences from the references are primarily due to the inherent assumptions and limitations of the modal approach. In particular, they cannot resolve the abrupt size transition between the interstitial and activated aerosol fractions. For the 12- and 36-section approaches, differences are largely due to limitations of the parameterized activation for non-log-normal size distributions, plus the coarse resolution for the 12-section case. Differences are larger both with higher aerosol (i.e., less complete activation) and higher SO2 concentrations (i.e., greater modification of the initial aerosol distribution).

  9. Impact of aerosol size representation on modeling aerosol-cloud interactions

    DOE PAGESBeta

    Zhang, Y.; Easter, R. C.; Ghan, S. J.; Abdul-Razzak, H.

    2002-11-07

    In this study, we use a 1-D version of a climate-aerosol-chemistry model with both modal and sectional aerosol size representations to evaluate the impact of aerosol size representation on modeling aerosol-cloud interactions in shallow stratiform clouds observed during the 2nd Aerosol Characterization Experiment. Both the modal (with prognostic aerosol number and mass or prognostic aerosol number, surface area and mass, referred to as the Modal-NM and Modal-NSM) and the sectional approaches (with 12 and 36 sections) predict total number and mass for interstitial and activated particles that are generally within several percent of references from a high resolution 108-section approach.more » The modal approach with prognostic aerosol mass but diagnostic number (referred to as the Modal-M) cannot accurately predict the total particle number and surface areas, with deviations from the references ranging from 7-161%. The particle size distributions are sensitive to size representations, with normalized absolute differences of up to 12% and 37% for the 36- and 12-section approaches, and 30%, 39%, and 179% for the Modal-NSM, Modal-NM, and Modal-M, respectively. For the Modal-NSM and Modal-NM, differences from the references are primarily due to the inherent assumptions and limitations of the modal approach. In particular, they cannot resolve the abrupt size transition between the interstitial and activated aerosol fractions. For the 12- and 36-section approaches, differences are largely due to limitations of the parameterized activation for non-log-normal size distributions, plus the coarse resolution for the 12-section case. Differences are larger both with higher aerosol (i.e., less complete activation) and higher SO2 concentrations (i.e., greater modification of the initial aerosol distribution).« less

  10. Investigation of the time evolved spatial distribution of urban PM2.5 concentrations and aerosol composition during episodic high PM events in Yuma, AZ

    NASA Astrophysics Data System (ADS)

    Holmes, Heather A.; Pardyjak, Eric R.; Tyler, Bonnie J.; Peterson, Richard E.

    An interdisciplinary field study designed to investigate the spatial and temporal variability of atmospheric aerosols during high particulate matter ( PM) events along the US-Mexico border near Yuma, AZ was run during the week of March 18, 2007. The experiments were designed to quantify chemical composition and physical phenomena governing the transport of aerosols generated from episodic high PM events. The field study included two micrometeorological monitoring sites; one rural and one urban, equipped with sonic anemometers, continuous particulate concentration monitors and ambient aerosol collection equipment. In addition to the two main monitoring sites, five additional locations were equipped with optical particle counters to allow for the investigation of the spatial and temporal distribution of PM2.5 in the urban environment. In this paper, the meteorological and turbulence parameters governing the distribution and concentration of PM2.5 in the urban environment for two high-wind erosion events and one burning event are compared. The interaction between local atmospheric conditions and the particulate distribution is investigated. Results indicate that a single point measurement in the urban area of Yuma may not be sufficient for determining the ambient PM concentrations that the local population experiences; all three high PM events indicated PM2.5 varied considerably with maximum urban concentrations 5-10 times greater than the measured minima. A comparison of inorganic and carbonaceous content of the aerosols for the three high PM events is presented. The comparison shows an increase in silicon during crustal dust events and an increase in elemental and organic carbon during the burn event. Additional surface chemistry analysis, using time-of-flight secondary ion mass spectrometry (ToF-SIMS), for aerosols collected at the urban and rural sites during the burn event are discussed. The surface chemistry analysis provides positive ion mass spectra of organic

  11. Application of WRF/Chem-MADRID and WRF/Polyphemus in Europe - Part 2: Evaluation of chemical concentrations, sensitivity simulations, and aerosol-meteorology interactions

    NASA Astrophysics Data System (ADS)

    Zhang, Y.; Sartelet, K.; Zhu, S.; Wang, W.; Wu, S.-Y.; Zhang, X.; Wang, K.; Tran, P.; Seigneur, C.; Wang, Z.-F.

    2013-02-01

    of PM10 concentrations at all sites. The differences between model predictions and observations are mostly caused by inaccurate representations of emissions of gaseous precursors and primary PM species, as well as biases in the meteorological predictions. The differences in model predictions are caused by differences in the heights of the first model layers and thickness of each layer that affect vertical distributions of emissions, model treatments such as dry/wet deposition, heterogeneous chemistry, and aerosol and cloud, as well as model inputs such as emissions of soil dust and sea-salt and chemical boundary conditions of CO and O3 used in both models. WRF/Chem-MADRID shows a higher sensitivity to grid resolution than WRF/Polyphemus at all sites. For both models, the use of a finer grid resolution generally leads to an overall better statistical performance for most variables, with greater spatial details and an overall better agreement in temporal variations and magnitudes at most sites. The use of online BVOC emissions gives better statistical performance for hourly and max 8-h O3 and PM2.5 and generally better agreement with their observed temporal variations at most sites. Because it is an online model, WRF/Chem-MADRID offers the advantage to account for various feedbacks between meteorology and chemical species. The simulations show that aerosol leads to reduced net shortwave radiation fluxes, 2-m temperature, 10-m wind speed, PBL height, and precipitation and increases aerosol optical depth, cloud condensation nuclei, cloud optical depth, and cloud droplet number concentrations over most of the domain. However, this model comparison suggests that atmospheric pollutant concentrations are most sensitive in state-of-the-science air quality models to vertical structure, inputs, and parameterizations for dry/wet removal of gases and particles in the model.

  12. Aerosol activation properties and CCN closure during TCAP

    NASA Astrophysics Data System (ADS)

    Mei, F.; Tomlinson, J. M.; Shilling, J. E.; Wilson, J. M.; Zelenyuk, A.; Chand, D.; Comstock, J. M.; Hubbe, J.; Berg, L. K.; Schmid, B.

    2013-12-01

    The indirect effects of atmospheric aerosols currently remain the most uncertain components in forcing of climate change over the industrial period (IPCC, 2007). This large uncertainty is partially due to our incomplete understanding of the ability of particles to form cloud droplets under atmospherically relevant supersaturation. In addition, there is a large uncertainty in the aerosol optical depth (AOD) simulated by climate models near the North American coast and a wide variety in the types of clouds are observed over this region. The goal of the US Department of Energy Two Column Aerosol Project (TCAP) is to understand the processes responsible for producing and maintaining aerosol distributions and associated radiative and cloud forcing off the coast of North America. During the TCAP study, aerosol total number concentration, cloud condensation nuclei (CCN) spectra and aerosol chemical composition were in-situ measured from the DOE Gulfstream 1 (G-1) research aircraft during two Intensive Operations Periods (IOPs), one conducted in July 2012 and the other in February 2013. An overall aerosol size distribution was achieved by merging the observations from several instruments, including Ultra High Sensitivity Aerosol Spectrometer - Airborne (UHSAS-A, DMT), Passive Cavity Aerosol Spectrometer Probe (PCASP-200, DMT), and Cloud Aerosol Spectrometer (CAS, DMT). Aerosol chemical composition was characterized using a high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS, Aerodyne Inc.) and single particle mass spectrometer, mini-SPLAT. Based on the aerosol size distribution, CCN number concentration (characterized by a DMT dual column CCN counter with a range from 0.1% to 0.4%), and chemical composition, a CCN closure was obtained. The sensitivity of CCN closure to organic hygroscopicity was investigated. The differences in aerosol/CCN properties between two columns, and between two phases, will be discussed.

  13. Airship measurements of aerosol size distributions, cloud droplet spectra, and trace gas concentrations in the marine boundary layers

    SciTech Connect

    Frick, G.M.; Hoppel, W.A. )

    1993-11-01

    The use of an airship as a platform to conduct atmospheric chemistry, aerosol, and cloud microphysical research is described, and results from demonstration flights made off the Oregon coast are presented. The slow speed of the airship makes it an ideal platform to do high-spatial resolution profiling both vertically and horizontally, and to measure large aerosol and cloud droplet distributions without the difficulties caused by high-speed aircraft sampling. A unique set of data obtained during the demonstration flights show the effect that processing marine boundary layer aerosol through stratus clouds has on the aerosol size distribution. Evidence of new particle formation (nucleation of particles) was also observed on about half the days on which flights were made. 11 refs., 9 figs., 1 tab.

  14. Measurements of Atmospheric Aerosol Vertical Distributions above Svalbard, Norway using Unmanned Aerial Systems (UAS)

    NASA Astrophysics Data System (ADS)

    Bates, T. S.; Johnson, J. E.; Stalin, S.; Telg, H.; Murphy, D. M.; Burkhart, J. F.; Quinn, P.; Storvold, R.

    2015-12-01

    Atmospheric aerosol vertical distributions were measured above Svalbard, Norway in April 2015 to investigate the processes controlling aerosol concentrations and radiative effects. The aerosol payload was flown in a NOAA/PMEL MANTA Unmanned Aerial System (UAS) on 9 flights totaling 19 flight hours. Measurements were made of particle number concentration and aerosol light absorption at three wavelengths, similar to those conducted in April 2011 (Bates et al., Atmos. Meas. Tech., 6, 2115-2120, 2013). A filter sample was collected on each flight for analyses of trace elements. Additional measurements in the aerosol payload in 2015 included aerosol size distributions obtained using a Printed Optical Particle Spectrometer (POPS) and aerosol optical depth obtained using a four wavelength miniature Scanning Aerosol Sun Photometer (miniSASP). The data show most of the column aerosol mass and resulting optical depth in the boundary layer but frequent aerosol layers aloft with high particle number concentration (2000 cm-3) and enhanced aerosol light absorption (1 Mm-1). Transport of these aerosol layers was assessed using FLEXPART particle dispersion models. The data contribute to an assessment of sources of BC to the Arctic and potential climate impacts.

  15. Measurements of atmospheric aerosol vertical distributions above Svalbard, Norway, using unmanned aerial systems (UAS)

    NASA Astrophysics Data System (ADS)

    Bates, T. S.; Quinn, P. K.; Johnson, J. E.; Corless, A.; Brechtel, F. J.; Stalin, S. E.; Meinig, C.; Burkhart, J. F.

    2013-08-01

    Atmospheric aerosol vertical distributions were measured above Svalbard, Norway, in April 2011 during the Cooperative Investigation of Climate-Cryosphere Interactions campaign (CICCI). Measurements were made of the particle number concentration and the aerosol light absorption coefficient at three wavelengths. A filter sample was collected on each flight at the altitude of maximum particle number concentration. The filters were analyzed for major anions and cations. The aerosol payload was flown in a NOAA/PMEL MANTA Unmanned Aerial System (UAS). A total of 18 flights were flown during the campaign totaling 38 flight hours. The data show frequent aerosol layers aloft with high particle number concentration (1000 cm-3) and enhanced aerosol light absorption (1 Mm-1). Air mass histories of these aerosol layers were assessed using FLEXPART particle dispersion modeling. The data contribute to an assessment of sources of BC to the Arctic and potential climate impacts.

  16. Measurements of atmospheric aerosol vertical distributions above Svalbard, Norway using unmanned aerial systems (UAS)

    NASA Astrophysics Data System (ADS)

    Bates, T. S.; Quinn, P. K.; Johnson, J. E.; Corless, A.; Brechtel, F. J.; Stalin, S. E.; Meinig, C.; Burkhart, J. F.

    2013-03-01

    Atmospheric aerosol vertical distributions were measured above Svalbard, Norway in April 2011 during the Cooperative Investigation of Climate-Cryosphere Interactions campaign (CICCI). Measurements were made of the particle number concentration and the aerosol light absorption coefficient at three wavelengths. A filter sample was collected on each flight at the altitude of maximum particle number concentration. The filters were analyzed for major anions and cations. The aerosol payload was flown in a NOAA/PMEL MANTA Unmanned Aerial System (UAS). A total of 18 flights were flown during the campaign totaling 38 flight hours. The data show frequent aerosol layers aloft with high particle number concentration (1000 cm-3 and enhanced aerosol light absorption (1 Mm-1). Air mass histories of these aerosol layers were assessed using FLEXPART particle dispersion modeling. The data contribute to an assessment of sources of BC to the Arctic and potential climate impacts.

  17. Application of a coupled aerosol formation: Radiative transfer model to climatic studies of aerosols

    NASA Technical Reports Server (NTRS)

    Toon, O. B.; Pollack, J. B.

    1979-01-01

    A sophisticated one dimensional physical-chemical model of the formation and evolution of stratospheric aerosols was used to predict the size and number concentration of the stratospheric aerosols as functions of time and altitude following: a large volcanic eruption; increased addition of carbonyl sulfide (OCS) or sulfur dioxide (SO2) to the troposphere; increased supersonic aircraft (SST) flights in the stratosphere; and, large numbers of space shuttle (SS) flights through the stratosphere. A radiative-convective one dimensional climate sensitivity study, using the results of the aerosol formation model, was performed to assess the ground level climatic significance of these perturbations to the stratospheric aerosol layer. Volcanic eruptions and large OCS or SO2 increases could cause significant climatic changes. Currently projected SS launches and moderate fleets of SST's are unlikely to upset the stratospheric aerosol layer enough to significantly impact climate.

  18. 40 CFR Table C-1 to Subpart C of... - Test Concentration Ranges, Number of Measurements Required, and Maximum Discrepancy Specifications

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 5 2011-07-01 2011-07-01 false Test Concentration Ranges, Number of Measurements Required, and Maximum Discrepancy Specifications C Table C-1 to Subpart C of Part 53 Protection of... Reference Methods Pt. 53, Subpt. C, Table C-1 Table C-1 to Subpart C of Part 53—Test Concentration...

  19. Understanding the impact of saharan dust aerosols on tropical cyclones

    NASA Astrophysics Data System (ADS)

    Naeger, Aaron

    Genesis of Tropical Cyclones (TCs) in the main development region for Atlantic hurricanes is tied to convection initiated by African easterly waves (AEWs) during Northern hemisphere summer and fall seasons. The main development region is also impacted by dust aerosols transported from the Sahara. It has been hypothesized that dust aerosols can modulate the development of TCs through aerosol-radiation and aerosol-cloud interaction processes. In this study, we investigate the impact of dust aerosols on TC development using the Weather Research and Forecasting model coupled with chemistry (WRF-Chem). We first develop a technique to constrain the WRF-Chem model with a realistic three-dimensional spatial distribution of dust aerosols. The horizontal distribution of dust is specified using the Moderate Resolution Imaging Spectroradiometer (MODIS) derived aerosol products and output from the Goddard Chemistry Aerosol Radiation and Transport (GOCART) model. The vertical distribution of dust is constrained using the Cloud Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO). We validate our technique through in situ aircraft measurements where both showed aerosol number concentrations from 20-30 cm-3 in the atmosphere for Saharan dust moving over the eastern Atlantic Ocean. Then, we use the satellite data constraint technique to nudge the WRF-Chem aerosol fields throughout the simulation of TC Florence developing over the eastern Atlantic Ocean during September 2006. Three different experiments are conducted where the aerosol-radiation and aerosol-cloud interaction processes are either activated or deactivated in the model while all other model options are identical between the experiments. By comparing the model experiment results, the impact of the aerosol interaction processes on TC development can be understood. The results indicate that dust aerosols can delay or prevent the development of a TC as the minimum sea level pressure of TC Florence was 13 h

  20. The impact of monthly variation of the Pacific-North America (PNA) teleconnection pattern on wintertime surface-layer aerosol concentrations in the United States

    NASA Astrophysics Data System (ADS)

    Feng, J.; Liao, H.; Li, J.

    2015-11-01

    The Pacific-North America teleconnection (PNA) is the leading general circulation pattern in the troposphere over the region of North Pacific to North America during wintertime. This study examined the impacts of monthly variation of the PNA phase (positive or negative phase) on wintertime surface-layer aerosol concentrations in the US by analyzing observations during 1999-2013 from the Air Quality System of Environmental Protection Agency (EPA-AQS) and the model results for 1986-2006 from the global three-dimensional Goddard Earth Observing System (GEOS) chemical transport model (GEOS-Chem). The composite analyses on the EPA-AQS observations over 1999-2003 showed that the average concentrations of PM2.5, sulfate, nitrate, ammonium, organic carbon, and black carbon aerosols over the US were higher in the PNA positive phases than in the PNA negative phases by 1.4 μg m-3 (12.7 %), 0.1 μg m-3 (6.4 %), 0.3 μg m-3 (39.1 %), 0.2 μg m-3 (22.8 %), 0.8 μg m-3 (21.3 %), and 0.2 μg m-3 (34.1 %), respectively. The simulated geographical patterns of the differences in concentrations of all aerosol species between the PNA positive and negative phases were similar to observations. Based on the GEOS-Chem simulation driven by the assimilated meteorological fields, the PNA-induced variation in planetary boundary layer height was found to be the most dominant meteorological factor that influenced the concentrations of PM2.5, sulfate, ammonium, organic carbon, and black carbon, and the PNA-induced variation in temperature was the most important parameter that influenced nitrate aerosol. Results from this work have important implications for understanding and prediction of air quality in the United States.

  1. Biogenic Contributions to Summertime Arctic Aerosol: Observations of Aerosol Composition from the Netcare 2014 Aircraft Campaign

    NASA Astrophysics Data System (ADS)

    Willis, M. D.; Burkart, J.; Koellner, F.; Schneider, J.; Bozem, H.; Hoor, P. M.; Brauner, R.; Herber, A. B.; Leaitch, W. R.; Abbatt, J.

    2014-12-01

    The Arctic is a complex and poorly studied aerosol environment, impacted by strong anthropogenic contributions during winter months and by regional sources in cleaner summer months. In order to gain a predictive understanding of the changing climate in this region, it is necessary to understand the balance between these two aerosol sources to clarify how aerosol might be altered by or contribute to climate change. We present results of vertically resolved, submicron aerosol composition from an Aerodyne high-resolution aerosol mass spectrometer (AMS) during the NETCARE 2014 Polar6 aircraft campaign. The campaign was based in the high Arctic, at Resolute, NU (74°N), allowing measurements from 60 to 2900 meters over ice, open water and near the ice-edge. Concurrent measurements aboard the Polar6 included ultrafine and accumulation mode particle number and size, cloud condensation nuclei concentrations, trace gas concentrations and single particle composition. Aerosol vertical profiles measured by the AMS can be broadly characterized into two regimes corresponding to different meteorological conditions: the first with very low aerosol loading (<0.1 μg/m3) at low altitudes compared to that aloft and high numbers of nucleation mode particles, and the second with higher concentrations at lower levels. This second regime was associated with low concentrations of nucleation mode particles, and higher observable levels of methane sulphonic acid (MSA) from AMS measurements at low altitudes. MSA, produced during the oxidation of dimethyl sulphide, is a marker for the contribution of ocean-derived biogenic sulphur to particulate sulphur and could be identified and quantified using the high-resolution AMS. MSA to sulphate ratios were observed to increase towards lower altitudes, suggesting a contribution to aerosol loading from the ocean. In addition, we present measurements of aerosol neutralization and the characteristics of organic aerosol that relate to the growth of

  2. Ensemble projections of wildfire activity and carbonaceous aerosol concentrations over the western United States in the mid-21st century

    PubMed Central

    Yue, Xu; Mickley, Loretta J.; Logan, Jennifer A.; Kaplan, Jed O.

    2013-01-01

    We estimate future wildfire activity over the western United States during the mid-21st century (2046–2065), based on results from 15 climate models following the A1B scenario. We develop fire prediction models by regressing meteorological variables from the current and previous years together with fire indexes onto observed regional area burned. The regressions explain 0.25–0.60 of the variance in observed annual area burned during 1980–2004, depending on the ecoregion. We also parameterize daily area burned with temperature, precipitation, and relative humidity. This approach explains ~0.5 of the variance in observed area burned over forest ecoregions but shows no predictive capability in the semi-arid regions of Nevada and California. By applying the meteorological fields from 15 climate models to our fire prediction models, we quantify the robustness of our wildfire projections at mid-century. We calculate increases of 24–124% in area burned using regressions and 63–169% with the parameterization. Our projections are most robust in the southwestern desert, where all GCMs predict significant (p<0.05) meteorological changes. For forested ecoregions, more GCMs predict significant increases in future area burned with the parameterization than with the regressions, because the latter approach is sensitive to hydrological variables that show large inter-model variability in the climate projections. The parameterization predicts that the fire season lengthens by 23 days in the warmer and drier climate at mid-century. Using a chemical transport model, we find that wildfire emissions will increase summertime surface organic carbon aerosol over the western United States by 46–70% and black carbon by 20–27% at midcentury, relative to the present day. The pollution is most enhanced during extreme episodes: above the 84th percentile of concentrations, OC increases by ~90% and BC by ~50%, while visibility decreases from 130 km to 100 km in 32 Federal Class 1

  3. Enhanced concentrations of citric acid in spring aerosols collected at the Gosan background site in East Asia

    NASA Astrophysics Data System (ADS)

    Jung, Jinsang; Kawamura, Kimitaka

    2011-09-01

    In order to investigate water-soluble dicarboxylic acids and related compounds in the aerosol samples under the Asian continent outflow, total suspended particle (TSP) samples ( n = 32) were collected at the Gosan site in Jeju Island over 2-5 days integration during 23 March-1 June 2007 and 16-24 April 2008. The samples were analyzed for water-soluble dicarboxylic acids, ketocarboxylic acids, and α-dicarbonyls using a capillary gas chromatography technique. We found elevated concentrations of atmospheric citric acid (range: 20-320 ng m -3) in the TSP samples during mid- to late April of 2007 and 2008. To specify the sources of citric acid, dicarboxylic acids and related compounds were measured in the pollen sample collected at the Gosan site (Pollen_Gosan), authentic pollen samples from Japanese cedar ( Cryptomeria) (Pollen_cedar) and Japanese cypress ( Chamaecyparis obtusa) (Pollen_cypress), and tangerine fruit produced from Jeju Island. Citric acid (2790 ng in unit mg of pollen mass) was found as most abundant species in the Pollen_Gosan, followed by oxalic acid (2390 ng mg -1). Although citric acid was not detected in the Pollen_cedar and Pollen_cypress as major species, it was found as a dominant species in the tangerine juice while malic acid was detected as major species in the tangerine peel, followed by oxalic and citric acids. Since Japanese cedar trees are planted around tangerine farms to prevent strong winds from the Pacific Ocean, citric acid that may be directly emitted from tangerine is likely adsorbed on pollens emitted from Japanese cedar and then transported to the Gosan site. Much lower malic/citric acid ratios obtained under cloudy condition than clear condition suggest that malic acid may rapidly decompose to lower molecular weight compounds such as oxalic and malonic acids (

  4. Global upper ocean heat storage response to radiative forcing from changing solar irradiance and increasing greenhouse gas/aerosol concentrations

    NASA Astrophysics Data System (ADS)

    White, Warren B.; Cayan, Daniel R.; Lean, Judith

    1998-09-01

    We constructed gridded fields of diabatic heat storage changes in the upper ocean from 20°S to 60°N from historical temperature profiles collected from 1955 to 1996. We filtered these 42 year records for periods of 8 to 15 years and 15 to 30 years, producing depth-weighted vertical average temperature (DVT) changes from the sea surface to the top of the main pycnocline. Basin and global averages of these DVT changes reveal decadal and interdecadal variability in phase across the Indian, Pacific, Atlantic, and Global Oceans, each significantly correlated with changing surface solar radiative forcing at a lag of 0+/-2 years. Decadal and interdecadal changes in global average DVT are 0.06°+/-0.01°K and 0.04°K+/-0.01°K, respectively, the same as those expected from consideration of the Stefan-Boltzmann radiation balance (i.e., 0.3°K per Wm-2) in response to 0.1% changes in surface solar radiative forcing of 0.2 Wm-2 and 0.15 Wm-2, respectively. Global spatial patterns of DVT changes are similar to temperature changes simulated in coupled ocean-atmosphere models, suggesting that natural modes of Earth's variability are phase-locked to the solar irradiance cycle. A trend in global average DVT of 0.15°K over this 42 year record cannot be explained by changing surface solar radiative forcing. But when we consider the 0.5 Wm-2 increase in surface radiative forcing estimated from the increase in atmospheric greenhouse gas and aerosol (GGA) concentrations over this period [Intergovernmental Panel on Climate Change, 1995], the Stefan-Boltzmann radiation balance yields this observed change. Moreover, the sum of solar and GGA surface radiative forcing can explain the relatively sharp increase in global and basin average DVT in the late 1970's.

  5. Ensemble projections of wildfire activity and carbonaceous aerosol concentrations over the western United States in the mid-21st century

    NASA Astrophysics Data System (ADS)

    Yue, Xu; Mickley, Loretta J.; Logan, Jennifer A.; Kaplan, Jed O.

    2013-10-01

    We estimate future wildfire activity over the western United States during the mid-21st century (2046-2065), based on results from 15 climate models following the A1B scenario. We develop fire prediction models by regressing meteorological variables from the current and previous years together with fire indexes onto observed regional area burned. The regressions explain 0.25-0.60 of the variance in observed annual area burned during 1980-2004, depending on the ecoregion. We also parameterize daily area burned with temperature, precipitation, and relative humidity. This approach explains ˜0.5 of the variance in observed area burned over forest ecoregions but shows no predictive capability in the semi-arid regions of Nevada and California. By applying the meteorological fields from 15 climate models to our fire prediction models, we quantify the robustness of our wildfire projections at midcentury. We calculate increases of 24-124% in area burned using regressions and 63-169% with the parameterization. Our projections are most robust in the southwestern desert, where all GCMs predict significant (p < 0.05) meteorological changes. For forested ecoregions, more GCMs predict significant increases in future area burned with the parameterization than with the regressions, because the latter approach is sensitive to hydrological variables that show large inter-model variability in the climate projections. The parameterization predicts that the fire season lengthens by 23 days in the warmer and drier climate at midcentury. Using a chemical transport model, we find that wildfire emissions will increase summertime surface organic carbon aerosol over the western United States by 46-70% and black carbon by 20-27% at midcentury, relative to the present day. The pollution is most enhanced during extreme episodes: above the 84th percentile of concentrations, OC increases by ˜90% and BC by ˜50%, while visibility decreases from 130 km to 100 km in 32 Federal Class 1 areas in

  6. Ensemble projections of wildfire activity and carbonaceous aerosol concentrations over the western United States in the mid-21st century.

    PubMed

    Yue, Xu; Mickley, Loretta J; Logan, Jennifer A; Kaplan, Jed O

    2013-10-01

    We estimate future wildfire activity over the western United States during the mid-21(st) century (2046-2065), based on results from 15 climate models following the A1B scenario. We develop fire prediction models by regressing meteorological variables from the current and previous years together with fire indexes onto observed regional area burned. The regressions explain 0.25-0.60 of the variance in observed annual area burned during 1980-2004, depending on the ecoregion. We also parameterize daily area burned with temperature, precipitation, and relative humidity. This approach explains ~0.5 of the variance in observed area burned over forest ecoregions but shows no predictive capability in the semi-arid regions of Nevada and California. By applying the meteorological fields from 15 climate models to our fire prediction models, we quantify the robustness of our wildfire projections at mid-century. We calculate increases of 24-124% in area burned using regressions and 63-169% with the parameterization. Our projections are most robust in the southwestern desert, where all GCMs predict significant (p<0.05) meteorological changes. For forested ecoregions, more GCMs predict significant increases in future area burned with the parameterization than with the regressions, because the latter approach is sensitive to hydrological variables that show large inter-model variability in the climate projections. The parameterization predicts that the fire season lengthens by 23 days in the warmer and drier climate at mid-century. Using a chemical transport model, we find that wildfire emissions will increase summertime surface organic carbon aerosol over the western United States by 46-70% and black carbon by 20-27% at midcentury, relative to the present day. The pollution is most enhanced during extreme episodes: above the 84(th) percentile of concentrations, OC increases by ~90% and BC by ~50%, while visibility decreases from 130 km to 100 km in 32 Federal Class 1 areas in

  7. Zone of influence for particle number concentrations at signalised traffic intersections

    NASA Astrophysics Data System (ADS)

    Goel, Anju; Kumar, Prashant

    2015-12-01

    Estimation of zone of influences (ZoI) at signalised traffic intersections (TI) is important to accurately model particle number concentrations (PNCs) and their exposure to public at emission hotspot locations. However, estimates of ZoI for PNCs at different types of TIs are barely known. We carried out mobile measurements inside the car cabin with windows fully open for size-resolved PNCs in the 5-560 nm range on a 6 km long busy round route that had 10 TIs. These included four-way TIs without built-up area (TI4w-nb), four-way TIs with built-up area (TI4w-wb), three-way TIs without built-up area (TI3w-nb) and three-way TIs with built-up area (TI3w-wb). Mobile measurements were made with a fast response differential mobility spectrometer (DMS50). Driving speed and position of the car were recorded every second using a global positioning system (GPS). Positive matrix factorisation (PMF) modelling was applied on the data to quantify the contribution of PNCs released during deceleration, creep-idling, acceleration and cruising to total PNCs at the TIs. The objectives were to address the following questions: (i) how does ZoI vary at different types of TIs in stop- and go-driving conditions?, (ii) what is the effect of different driving conditions on ZoI of a TI?, (iii) how realistically can the PNC profiles be generalised within a ZoI of a TI?, and (iv) what is the share of emissions during different driving conditions towards the total PNCs at a TI? Average length of ZoI in longitudinal direction and along the road was found to be the highest (148 m; 89 to -59 m from the centre of a TI) at a TI3w-wb, followed by TI4w-nb (129 m; 79 to -42 m), TI3w-nb (86 m; 71 to -15 m) and TI4w-wb (79 m; 46 to -33 m) in stop- and go-driving conditions. During multiple stopping driving conditions when a vehicle stops at a TI more than once in a signal cycle due to oversaturation of vehicles, average length of ZoI increased by 55, 22 and 21% at TI4w-nb, TI3w-nb and TI3w-wb, respectively

  8. How We Can Constrain Aerosol Type Globally

    NASA Technical Reports Server (NTRS)

    Kahn, Ralph

    2016-01-01

    In addition to aerosol number concentration, aerosol size and composition are essential attributes needed to adequately represent aerosol-cloud interactions (ACI) in models. As the nature of ACI varies enormously with environmental conditions, global-scale constraints on particle properties are indicated. And although advanced satellite remote-sensing instruments can provide categorical aerosol-type classification globally, detailed particle microphysical properties are unobtainable from space with currently available or planned technologies. For the foreseeable future, only in situ measurements can constrain particle properties at the level-of-detail required for ACI, as well as to reduce uncertainties in regional-to-global-scale direct aerosol radiative forcing (DARF). The limitation of in situ measurements for this application is sampling. However, there is a simplifying factor: for a given aerosol source, in a given season, particle microphysical properties tend to be repeatable, even if the amount varies from day-to-day and year-to-year, because the physical nature of the particles is determined primarily by the regional environment. So, if the PDFs of particle properties from major aerosol sources can be adequately characterized, they can be used to add the missing microphysical detail the better sampled satellite aerosol-type maps. This calls for Systematic Aircraft Measurements to Characterize Aerosol Air Masses (SAM-CAAM). We are defining a relatively modest and readily deployable, operational aircraft payload capable of measuring key aerosol absorption, scattering, and chemical properties in situ, and a program for characterizing statistically these properties for the major aerosol air mass types, at a level-of-detail unobtainable from space. It is aimed at: (1) enhancing satellite aerosol-type retrieval products with better aerosol climatology assumptions, and (2) improving the translation between satellite-retrieved aerosol optical properties and

  9. A Physically-Based Estimate of Radiative Forcing by Anthropogenic Sulfate Aerosol

    SciTech Connect

    Ghan, Steven J.); Easter, Richard C.); Chapman, Elaine G.); Abdul-Razzak, Hayder; Zhang, Yang ); Leung, Ruby ); Laulainen, Nels S.); Saylor, Rick D.); Zaveri, Rahul A.)

    2001-04-01

    Estimates of direct and indirect radiative forcing by anthropogenic sulfate aerosols from an integrated global aerosol and climate modeling system are presented. A detailed global tropospheric chemistry and aerosol model that predicts concentrations of oxidants as well as aerosols and aerosol precursors, is coupled to a general circulation model that predicts both cloud water mass and cloud droplet number. Both number and mass of several externally-mixed aerosol size modes are predicted, with internal mixing assumed for the different aerosol components within each mode. Predicted aerosol species include sulfate, organic and black carbon, soil dust, and sea salt. The models use physically-based treatments of aerosol radiative properties (including dependence on relative humidity) and aerosol activation as cloud condensation nuclei. Parallel simulations with and without anthropogenic sulfate aerosol are performed for a global domain. The global and annual mean direct and indirect radiative forcing due to anthropogenic sulfate are estimated to be -0.3 to -0.5 and -1.5 to -3.0 W m-2, respectively. The radiative forcing is sensitive to the model's horizontal resolution, the use of predicted vs. analyzed relative humidity, the prediction vs. diagnosis of aerosol number and droplet number, and the parameterization of droplet collision/coalescence. About half of the indirect radiative forcing is due to changes in droplet radius and half to increased cloud liquid water.

  10. Analysis of spatial and seasonal distributions of MODIS aerosol optical properties and ground-based measurements of mass concentrations in the Yellow Sea region in 2009.

    PubMed

    Kim, Hak-Sung; Chung, Yong-Seung; Lee, Sun-Gu

    2013-01-01

    Satellite-retrieved data on aerosol optical depth (AOD) and Ångström exponent (AE) using a moderate resolution imaging spectrometer (MODIS) were used to analyze large-scale distributions of atmospheric aerosols in East Asia. AOD was relatively high in March (0.44 ± 0.25) and low in September (0.24 ± 0.21) in the East Asian region in 2009. Sandstorms originating from the deserts and dry areas in northern China and Mongolia were transported on a massive scale during the springtime, thus contributing to the high AOD in East Asia. However, whereas PM10 with diameters ≤10 μm was the highest in February at Anmyon, Cheongwon, and Ulleung, located leeward about halfway through the Korean Peninsula, AOD rose to its highest in May. The growth of hygroscopic aerosols attendant on increases in relative humidity prior to the Asian monsoon season contributed to a high AOD level in May. AE typically appears at high levels (1.30 ± 0.37) in August due to anthropogenic aerosols originating from the industrial areas in eastern China, while AOD stays low in summer due to the removal process caused by rainfall. The linear correlation coefficients of the MODIS AOD and ground-based mass concentrations of PM10 at Anmyon, Cheongwon, and Ulleung were measured at 0.4~0.6. Four cases (6 days) of mineral dustfall from sandstorms and six cases (12 days) of anthropogenically polluted particles were observed in the central area of the Korean Peninsula in 2009. PM10 mass concentrations increased at both Anmyon and Cheongwon in the cases of mineral dustfall and anthropogenically polluted particles. Cases of dustfall from sandstorms and anthropogenic polluted particles, with increasing PM10 mass concentrations, showed higher AOD values in the Yellow Sea region. PMID:22362557

  11. Aerosol chamber and modelling studies on the reaction of soot aerosols with ozone

    SciTech Connect

    Moehler, O.; Naumann, K.H.; Saathoff, H.

    1995-12-31

    Heterogeneous processes in atmospheric aerosols are known to play important roles in the chemical transformation of air pollutants. Especially irregularly shaped aerosol particles like soot have large surface areas to interact with trace gases. The overall efficiency of those processes depends on various parameters like the particle shape, the chemical surface conditions, the surface reaction mechanisms and the gas transport processes to and from the surface. The shape and surface of soot particles are transformed due to their heterogeneous chemical activity. Therefore, the surface reaction efficiency of atmospheric soot particles also depends on their age and history. The scope of this work is to investigate the ozone depletion potential of soot particles at typical atmospheric conditions. The experiments are carried out in a cylindrical aerosol vessel with a volume of 3.7 m{sup 3}. The soot aerosol is produced with a sparc generator and introduced into the aerosol vessel together with the ozone. The variation of the number concentration, the mass concentration and the size distribution of the soot aerosol within the aerosol vessel is measured and electron micrographs are taken to obtain information on the particle morphology. The ozone concentration is continuously monitored by UV-absorption. The experimental data are compared with model results to analyze the physical and chemical processes in the aerosol system in more detail. The aerosol model developed at our institute is based on the concept of fractal geometry and calculates the dynamic behaviour of irregularly shaped aerosols. More recently, the model was extended to describe the interaction of the aerosol particles with gases. This paper summarizes first results of the experimental and modelling work. The possible impact on tropospheric chemistry will be discussed.

  12. Comprehensive Measurement of Atmospheric Aerosols with a Wide Range Aerosol Spectrometer

    NASA Astrophysics Data System (ADS)

    Keck, L.; Pesch, M.; Grimm, H.

    2011-07-01

    A wide range aerosol spectrometer (WRAS) was used for comprehensive long term measurements of aerosol size distributions. The system combines the results of an optical aerosol spectrometer with the results of a Scanning Mobility Particle Sizer (SMPS) to record essentially the full size range (5 nm - 32 μm) of atmospheric particles in 72 channels. Measurements were carried out over one year (2009) at the Global Atmospheric Watch (GAW)-Station Hohenpeißenberg, Bavaria. Total particle number concentrations obtained from the aerosol size distributions were compared to the total number concentrations measured by a Condensation Particle Counter (CPC). The comparison showed an excellent agreement of the data. The high time resolution of 5 minutes allows the combination of the measured size distributions with meteorological data and correlations to gaseous pollutants (CO, NOx and SO2). A good correlation of particle number and CO concentrations was found for long distance transported small particles, which were probably mainly soot particles. Correlations to NOx were observed for aerosols from local sources such as traffic emissions. The formation of secondary aerosols from gaseous precursors was also observed. Episodes of relatively high concentration of particles in the range of 2-3 μm were probably caused by pollen.

  13. Hourly Measurement of the Concentration and Gas-Particle Partitioning of Oxygenated Organic Tracers in Ambient Aerosol: First Results from Berkeley, CA and Rural Alabama

    NASA Astrophysics Data System (ADS)

    Isaacman, G. A.; Kreisberg, N. M.; Yee, L.; Chan, A.; Worton, D. R.; Hering, S. V.; Goldstein, A. H.

    2013-12-01

    Hourly and bi-hourly time-resolved measurements of organic tracer compounds in ambient aerosols have been successfully used to elucidate sources and formation pathways of atmospheric particulate matter. Here we extend the Semi-Volatile Thermal desorption Aerosol Gas chromatograph (SVTAG), a custom in-situ instrument that collects, desorbs, and analyzes ambient aerosol and semi-volatile compounds with hourly time resolution, to include on-line derivatization and a second, parallel collection cell that provides simultaneous collection of both particle-phase and particle-plus-gas-phase organic compounds. By introducing a silylating agent upon desorption, SVTAG can measure highly oxygenated compounds that are not easily detected using traditional gas chromatography including most of the previously reported oxygenated tracers for biogenic and anthropogenic secondary organic aerosol. The use of a pair of matched collection cells with parallel sampling and serial analysis provides direct gas-particle partitioning information. One cell collects the total organic fraction of compounds with volatilities lower than a C13 hydrocarbon, while the other cell samples through an activated carbon denuder to selectively remove the gas-phase components. Taken together these provide a direct measurement of gas-particle partitioning to yield a check on classical absorption based partitioning theory while deviations from this theory provide constraints on other driving factors in aerosol formation chemistry, such as oligomerization, salt formation, and acidity. We present here the capabilities and utility of the dual cell SVTAG with derivatization, with chemical insights gained from initial tests on ambient Berkeley air and the first results from a rural site in Alabama obtained during the Southern Oxidant and Aerosol Study (SOAS). Tracers for varying isoprene oxidation pathways are used to explore the influence of anthropogenic emissions; concentrations of 2-methyltetrols and 2-methyl

  14. Decadal increase in the number of recreational users is concentrated in no-take marine reserves.

    PubMed

    Gonson, Charles; Pelletier, Dominique; Gamp, Elodie; Preuss, Bastien; Jollit, Isabelle; Ferraris, Jocelyne

    2016-06-15

    In coastal areas, demographic increase is likely to result in greater numbers of recreational users, with potential consequences on marine biodiversity. These effects may also occur within Marine Protected Areas (MPAs), which are popular with recreational users. Our analysis builds on data collected over a ten-year period during three year-round surveys to appraise changes in recreational boating activities in coral ecosystems. Results show that the number of boaters has greatly increased, particularly so within MPAs during weekends and the warm season, when peaks in boat numbers have become more frequent. We also observed that the number of anchored boats has increased over the period. These changes may be resulting in biophysical impacts that could be detrimental to conservation objectives in MPAs. This steady increase over time may cause changes in the spatial and temporal distribution of users and in their practices, thus highlighting the importance of monitoring recreational activities. PMID:27103423

  15. Intercomparison of methods to measure the mass concentration of the atmospheric aerosol during INTERCOMP2000—influence of instrumentation and size cuts

    NASA Astrophysics Data System (ADS)

    Hitzenberger, R.; Berner, A.; Galambos, Z.; Maenhaut, W.; Cafmeyer, J.; Schwarz, J.; Müller, K.; Spindler, G.; Wieprecht, W.; Acker, K.; Hillamo, R.; Mäkelä, T.

    Within the EUROTRAC-2 subproject AEROSOL, the intensive field campaign INTERCOMP2000 was conducted to compare aerosol samplers and methods to measure various aerosol properties. Here a comparison of mass concentrations measured with different PM2.5 and PM10 samplers as well as cascade impactors is described. Different filter types were used. In general, the PM2.5 and PM10 mass concentrations obtained on filters agree well. The data agree within 18.1% (PM2.5, all data). If data obtained with the TEOM (18% low) and on Whatman QM-A quartz fibre filters (low face velocity, 38% high) are excluded, PM2.5 data agree within 8.1%. For PM10, the agreement is within 6.6% (again excluding the Whatman QM-A quartz fibre filters, 22% high) or 12.1% (all data). For the impactor samples, the data agreed within 6.3% (excluding the ELPI, which was 92% high) and 8.7% for PM2.5 and PM10.

  16. GCM Simulations of the