Science.gov

Sample records for affi-gel blue gel

  1. Characteristics of polyacrylamide gel with THPC and Turnbull Blue gel dosimeters evaluated using optical tomography

    NASA Astrophysics Data System (ADS)

    Pilařová (Vávrů), Kateřina; Kozubíková, Petra; Šolc, Jaroslav; Spěváček, Václav

    2014-11-01

    The purpose of this study was to compare characteristics of radiochromic gel - Turnbull Blue gel (TB gel) with polymer gel - polyacrylamide gel and tetrakis hydroxymethyl phosphonium chloride (PAGAT) using optical tomography. Both types of gels were examined in terms of dose sensitivity, dose response linearity and background value of spectrophotometric absorbance. The calibration curve was obtained for 60Co irradiation performed on Gammacell 220 at predefined gamma dose levels between 0 and 140 Gy for TBG and 0-15 Gy for PAGAT. To measure relative dose distributions from stereotactic irradiation, dosimeters were irradiated on Leksell Gamma Knife Perfexion. The cylindrical glass housings filled with gel were attached to the stereotactic frame. They were exposed with single shot and 16 mm collimator by 65 Gy to a 50% prescription isodose for TB gel and 4 Gy to a 50% prescription isodose for PAGAT. Evaluations of dosimeters were performed on an UV-vis Spectrophotometer Helios β and an optical cone beam homemade tomography scanner with a 16-bit astronomy CCD camera with a set of color filters. The advantages and potential disadvantages for both types of gel dosimeters were summarized. Dose distribution in central slice and measured profiles of 16 mm shot shows excellent correspondence with treatment planning system Leksell GammaPlan® for both PAGAT and Turnbull Blue gels. Gel dosimeters are suitable for steep dose gradient verification. An optical tomography evaluation method is successful. Dose response characteristics of TB gel and PAGAT gel are presented.

  2. Stretchable liquid-crystal blue-phase gels

    NASA Astrophysics Data System (ADS)

    Castles, F.; Morris, S. M.; Hung, J. M. C.; Qasim, M. M.; Wright, A. D.; Nosheen, S.; Choi, S. S.; Outram, B. I.; Elston, S. J.; Burgess, C.; Hill, L.; Wilkinson, T. D.; Coles, H. J.

    2014-08-01

    Liquid-crystalline polymers are materials of considerable scientific interest and technological value. An important subset of these materials exhibit rubber-like elasticity, combining the optical properties of liquid crystals with the mechanical properties of rubber. Moreover, they exhibit behaviour not seen in either type of material independently, and many of their properties depend crucially on the particular mesophase employed. Such stretchable liquid-crystalline polymers have previously been demonstrated in the nematic, chiral-nematic, and smectic mesophases. Here, we report the fabrication of a stretchable gel of blue phase I, which forms a self-assembled, three-dimensional photonic crystal that remains electro-optically switchable under a moderate applied voltage, and whose optical properties can be manipulated by an applied strain. We also find that, unlike its undistorted counterpart, a mechanically deformed blue phase exhibits a Pockels electro-optic effect, which sets out new theoretical challenges and possibilities for low-voltage electro-optic devices.

  3. Stretchable liquid-crystal blue-phase gels.

    PubMed

    Castles, F; Morris, S M; Hung, J M C; Qasim, M M; Wright, A D; Nosheen, S; Choi, S S; Outram, B I; Elston, S J; Burgess, C; Hill, L; Wilkinson, T D; Coles, H J

    2014-08-01

    Liquid-crystalline polymers are materials of considerable scientific interest and technological value. An important subset of these materials exhibit rubber-like elasticity, combining the optical properties of liquid crystals with the mechanical properties of rubber. Moreover, they exhibit behaviour not seen in either type of material independently, and many of their properties depend crucially on the particular mesophase employed. Such stretchable liquid-crystalline polymers have previously been demonstrated in the nematic, chiral-nematic, and smectic mesophases. Here, we report the fabrication of a stretchable gel of blue phase I, which forms a self-assembled, three-dimensional photonic crystal that remains electro-optically switchable under a moderate applied voltage, and whose optical properties can be manipulated by an applied strain. We also find that, unlike its undistorted counterpart, a mechanically deformed blue phase exhibits a Pockels electro-optic effect, which sets out new theoretical challenges and possibilities for low-voltage electro-optic devices. PMID:24880732

  4. Influence of gelling agents on the dosimetric performance of the Turnbull Blue gel dosimeter

    NASA Astrophysics Data System (ADS)

    Šolc, Jaroslav; Sochor, Vladimír; Spěváček, Václav

    2010-11-01

    Gelling agents such as agarose, phytagel, and several types of gelatin were used for preparation of Turnbull Blue radiochromic gel dosimeter. Their influence on gel dose response and background value was assessed. It was found that all gelatins cause significant increase of background in a short period of time after gel preparation therefore gelatin is not a suitable gelling agent for this dosimeter. Phytagel and agarose gels exhibit low and stable background and higher dose sensitivity than gelatin gels; however, the disadvantage is increased scattered light intensity in the gel in comparison to gelatin gels. A simple measurement was done demonstrating that the scattered light intensity significantly increases in phytagel and agarose gel in comparison to gelatin gels.

  5. Optimal parameters for laccase-mediated destaining of Coomassie Brilliant Blue R-250-stained polyacrylamide gels.

    PubMed

    Yang, Jie; Yang, Xiaodan; Ye, Xiuyun; Lin, Juan

    2016-06-01

    The data presented in this article are related to the research article entitled "Destaining of Coomassie Brilliant Blue R-250-stained polyacrylamide gels with fungal laccase" [1]. Laccase is a class of multicopper oxidases that can catalyze oxidation of recalcitrant dyestuffs. This article describes optimal parameters for destaining of polyacrylamide gels, stained with Coomassie Brilliant Blue R-250, with laccase from basidiomycete Cerrena sp. strain HYB07. Effects of laccase activity, mediator type and concentration, temperature and time on destaining of polyacrylamide gels were evaluated with respect to gel background intensity and protein band signals, and the optimal destaining effects were obtained with 15 U mL(-1) laccase and 2 μM ABTS at 37 °C after 2 h. PMID:26955647

  6. New radiochromic gel for 3D dosimetry based on Turnbull blue: basic properties.

    PubMed

    Solc, Jaroslav; Spevácek, Václav

    2009-09-01

    The recently developed new radiochromic gel dosimeter based on Turnbull blue dye formed by irradiation (the TBG dosimeter) does not exhibit dose pattern degradation due to diffusion effects as observed in the Fricke-gel dosimeter with xylenol orange incorporated into the gel matrix (the FXG dosimeter). The TBG dosimeter can be easily prepared and its optical properties enable evaluation of the gel's response using the cone-beam optical computed tomography technique. The preparation procedure is described in the paper along with the basic characteristics of the gel, including dose response, dose sensitivity, ageing under different storage conditions, diffusion rates of Turnbull blue and gel density. The measurement of diffusion is described in more detail. The same method was applied to the FXG dosimeter for direct comparison. It was found that the diffusion coefficient of the TBG dosimeter stored at 24 degrees C is less than 4 x 10(-3) mm(2) h(-1) (1sigma confidence level), compared to the value of 7.3 x 10(-1) mm(2) h(-1) (1sigma) of the FXG dosimeter measured at the same temperature. Although the TBG dosimeter is less sensitive than the FXG dosimeter, its diffusion coefficient is practically negligible and, therefore, it offers large potential as a three-dimensional dosimeter for applications encompassing sharp dose gradients such as high-dose-rate brachytherapy. PMID:19652291

  7. The monitoring of nucleotide diphosphate kinase activity by blue native polyacrylamide gel electrophoresis.

    PubMed

    Mailloux, Ryan J; Darwich, Rami; Lemire, Joseph; Appanna, Vasu

    2008-04-01

    Nucleoside diphosphate kinase (NDPK) has been shown to play a pivotal role in modulating a plethora of cellular processes. In this study, we report on a blue native (BN) PAGE technique which allows the facile assessment of NDPK activity and expression. The in-gel detection of NDPK relies on the precipitation of formazan at the site of immobilized enzyme activity. This is achieved by coupling the formation of ATP, as a consequence of gamma-phosphate transfer from NTP to ADP, to hexokinase (HK), glucose-6-phosphate dehydrogenase (G6PDH), oxidized nicotinamide adenine dinucleotide phosphate (NADP), phenazine methosulfate (PMS), and iodonitrotetrazolium chloride (INT). 2-D denaturing gel analysis confirmed that the activity bands corresponded to NDPK as indicated by subunit composition. Furthermore, the sensitivity and specificity of this readily accessible procedure was assessed by monitoring the in-gel activity of NDPK using different concentrations of GTP and CTP as well as deoxynucleoside triphosphates. This electrophoretic technique allows the quick and easy detection of NDPK, a housekeeping enzyme crucial to cell survival. PMID:18324728

  8. Blue native polyacrylamide gel electrophoresis (BN-PAGE) for analysis of multiprotein complexes from cellular lysates.

    PubMed

    Fiala, Gina J; Schamel, Wolfgang W A; Blumenthal, Britta

    2011-01-01

    Multiprotein complexes (MPCs) play a crucial role in cell signalling, since most proteins can be found in functional or regulatory complexes with other proteins (Sali, Glaeser et al. 2003). Thus, the study of protein-protein interaction networks requires the detailed characterization of MPCs to gain an integrative understanding of protein function and regulation. For identification and analysis, MPCs must be separated under native conditions. In this video, we describe the analysis of MPCs by blue native polyacrylamide gel electrophoresis (BN-PAGE). BN-PAGE is a technique that allows separation of MPCs in a native conformation with a higher resolution than offered by gel filtration or sucrose density ultracentrifugation, and is therefore useful to determine MPC size, composition, and relative abundance (Schägger and von Jagow 1991); (Schägger, Cramer et al. 1994). By this method, proteins are separated according to their hydrodynamic size and shape in a polyacrylamide matrix. Here, we demonstrate the analysis of MPCs of total cellular lysates, pointing out that lysate dialysis is the crucial step to make BN-PAGE applicable to these biological samples. Using a combination of first dimension BN- and second dimension SDS-PAGE, we show that MPCs separated by BN-PAGE can be further subdivided into their individual constituents by SDS-PAGE. Visualization of the MPC components upon gel separation is performed by standard immunoblotting. As an example for MPC analysis by BN-PAGE, we chose the well-characterized eukaryotic 19S, 20S, and 26S proteasomes. PMID:21403626

  9. Effects of composition interactions on the response of a turnbull blue radiochromic gel dosimeter

    NASA Astrophysics Data System (ADS)

    Shieh, Jiunn-I.; Cheng, Kai-Yuan; Shyu, Huey-Lih; Yu, Yi-Chen; Hsieh, Ling-Ling

    2014-11-01

    In this study, the Taguchi statistical method was used to design experiments for investigating the effects of interactions among compositions on the performance of a Turnbull blue gel (TBG) radiochromic dosimeter. Four parameters were considered as the design factors: (A) concentration of ferric chloride, (B) concentration of potassium ferricyanide, (C) concentration of sulfuric acid, and (D) amount of gelling agent added. Two levels were selected for each factor. The change in optical absorbance at 695 nm under UVA exposures was monitored to determine the response of the dosimeters. The results showed that the contributions of factors A-D on the absorbance were 20.01%, 23.16%, 27.03%, and 0.49%, respectively. The contributions of significant interaction effects were AC (8.60%), BC (5.61%), and ABC (10.56%). This finding indicated that sulfuric acid (C) was the most influential factor, whereas gelling agent (D) was the least influential factor. Sulfuric acid had an important function in two two-way interactions and one three-way interaction in the response of TBG to UV exposure.

  10. Methylene blue degradation by NaTaO3 sol-gel doped with Sm and La.

    PubMed

    Torres-Martínez, Leticia M; Cruz-López, Arquímedes; Juárez-Ramírez, Isaías; Meza-de la Rosa, Ma Elena

    2009-06-15

    In this work, NaTaO(3) compounds doped with 1M% of La and Sm, were prepared by the sol-gel (SG) method and solid state (SS) reaction; and tested as photocatalysts on the degradation of methylene blue (MB) under UV light. The structural characterization by X-ray powder diffraction revealed that the crystallization of the NaTaO(3) phase prepared by the sol-gel method started at 600 degrees C, reaching maximum crystallization at 800 degrees C. It was determined that the presence of Sm and La retard the crystallization of the NaTaO(3) phase. On the other hand, the compounds synthesized in this work showed particle sizes in the nanometric scale, as it was observed by scanning electron microscopy (SEM). The specific surface area of the compounds synthesized by the sol-gel method, showed values 4 times higher than those obtained by the solid state reaction, favoring their functional and photocatalytic performance in the methylene blue degradation. In addition, the best photocatalytic performance was shown by the NaTaO(3) doped with Sm and heated at 600 degrees C, having a half-life time of 65 min. PMID:19042087

  11. Investigation of the chemical origin and evidential value of differences in the SERS spectra of blue gel inks.

    PubMed

    Ho, Yen Cheng; Lee, Wendy W Y; Bell, Steven E J

    2016-08-15

    Highly swellable polymer films doped with Ag nanoparticle aggregates (poly-SERS films) have been used to record very high signal : noise ratio, reproducible surface-enhanced (resonance) Raman (SER(R)S) spectra of in situ dried ink lines and their constituent dyes using both 633 and 785 nm excitation. These allowed the chemical origins of differences in the SERRS spectra of different inks to be determined. Initial investigation of pure samples of the 10 most common blue dyes showed that the dyes which had very similar chemical structures such as Patent Blue V and Patent Blue VF (which differ only by a single OH group) gave SERRS spectra in which the only indications that the dye structure had been changed were small differences in peak positions or relative intensities of the bands. SERRS studies of 13 gel pen inks were consistent with this observation. In some cases inks from different types of pens could be distinguished even though they were dominated by a single dye such as Victoria Blue B (Zebra Surari) or Victoria Blue BO (Pilot Acroball) because their predominant dye did not appear in other inks. Conversely, identical spectra were also recorded from different types of pens (Pilot G7, Zebra Z-grip) because they all had the same dominant Brilliant Blue G dye. Finally, some of the inks contained mixtures of dyes which could be separated by TLC and removed from the plate before being analysed with the same poly-SERS films. For example, the Pentel EnerGel ink pen was found to give TLC spots corresponding to Erioglaucine and Brilliant Blue G. Overall, this study has shown that the spectral differences between different inks which are based on chemically similar, but nonetheless distinct dyes, are extremely small, so very close matches between SERRS spectra are required for confident identification. Poly-SERS substrates can routinely provide the very stringent reproducibility and sensitivity levels required. This, coupled with the awareness of the reasons

  12. Coomassie Blue as a Near-infrared Fluorescent Stain: A Systematic Comparison With Sypro Ruby for In-gel Protein Detection*

    PubMed Central

    Butt, R. Hussain; Coorssen, Jens R.

    2013-01-01

    Quantitative proteome analyses suggest that the well-established stain colloidal Coomassie Blue, when used as an infrared dye, may provide sensitive, post-electrophoretic in-gel protein detection that can rival even Sypro Ruby. Considering the central role of two-dimensional gel electrophoresis in top-down proteomic analyses, a more cost effective alternative such as Coomassie Blue could prove an important tool in ongoing refinements of this important analytical technique. To date, no systematic characterization of Coomassie Blue infrared fluorescence detection relative to detection with SR has been reported. Here, seven commercial Coomassie stain reagents and seven stain formulations described in the literature were systematically compared. The selectivity, threshold sensitivity, inter-protein variability, and linear-dynamic range of Coomassie Blue infrared fluorescence detection were assessed in parallel with Sypro Ruby. Notably, several of the Coomassie stain formulations provided infrared fluorescence detection sensitivity to <1 ng of protein in-gel, slightly exceeding the performance of Sypro Ruby. The linear dynamic range of Coomassie Blue infrared fluorescence detection was found to significantly exceed that of Sypro Ruby. However, in two-dimensional gel analyses, because of a blunted fluorescence response, Sypro Ruby was able to detect a few additional protein spots, amounting to 0.6% of the detected proteome. Thus, although both detection methods have their advantages and disadvantages, differences between the two appear to be small. Coomassie Blue infrared fluorescence detection is thus a viable alternative for gel-based proteomics, offering detection comparable to Sypro Ruby, and more reliable quantitative assessments, but at a fraction of the cost. PMID:24043422

  13. Analysis of Mutant SOD1 Electrophoretic Mobility by Blue Native Gel Electrophoresis; Evidence for Soluble Multimeric Assemblies

    PubMed Central

    Brown, Hilda H.; Borchelt, David R.

    2014-01-01

    Mutations in superoxide dismutase 1 (SOD1) cause familial forms of amyotrophic lateral sclerosis (fALS). Disease causing mutations have diverse consequences on the activity and half-life of the protein, ranging from complete inactivity and short half-life to full activity and long-half-life. Uniformly, disease causing mutations induce the protein to misfold and aggregate and such aggregation tendencies are readily visualized by over-expression of the proteins in cultured cells. In the present study we have investigated the potential of using immunoblotting of proteins separated by Blue-Native gel electrophoresis (BNGE) as a means to identify soluble multimeric forms of mutant protein. We find that over-expressed wild-type human SOD1 (hSOD1) is generally not prone to form soluble high molecular weight entities that can be separated by BNGE. For ALS mutant SOD1, we observe that for all mutants examined (A4V, G37R, G85R, G93A, and L126Z), immunoblots of BN-gels separating protein solubilized by digitonin demonstrated varied amounts of high molecular weight immunoreactive entities. These entities lacked reactivity to ubiquitin and were partially dissociated by reducing agents. With the exception of the G93A mutant, these entities were not reactive to the C4F6 conformational antibody. Collectively, these data demonstrate that BNGE can be used to assess the formation of soluble multimeric assemblies of mutant SOD1. PMID:25121776

  14. Sol–gel synthesis of SnO{sub 2}–MgO nanoparticles and their photocatalytic activity towards methylene blue degradation

    SciTech Connect

    Bayal, Nisha; Jeevanandam, P.

    2013-10-15

    Graphical abstract: - Highlights: • A simple sol–gel method for the synthesis of SnO{sub 2}–MgO nanoparticles is reported. • Band gap of SnO{sub 2} can be tuned by varying the magnesium content in SnO{sub 2}–MgO. • SnO{sub 2}–MgO shows good photocatalytic activity towards degradation of methylene blue. - Abstract: SnO{sub 2}–MgO mixed metal oxide nanoparticles were prepared by a simple sol–gel method. The nanoparticles were characterized by power X-ray diffraction, scanning electron microscopy coupled with energy dispersive X-ray analysis, transmission electron microscopy and UV–vis diffuse reflectance spectroscopy. The XRD results indicate the formation of mixed metal oxide nanoparticles and also a decrease of SnO{sub 2} crystallite size in the mixed metal oxide nanoparticles with increasing magnesium oxide content. The reflectance spectroscopy results show a blue shift of the band gap of SnO{sub 2} in the mixed metal oxide nanoparticles. The photocatalytic activity of the SnO{sub 2}–MgO nanoparticles was tested using the photodegradation of aqueous methylene blue in the presence of sunlight. The results indicate that the mixed metal oxide nanoparticles possess higher efficiency for the photodegradation of methylene blue compared to pure SnO{sub 2} nanoparticles.

  15. A facile approach to fabricate porous nanocomposite gels based on partially hydrolyzed polyacrylamide and cellulose nanocrystals for adsorbing methylene blue at low concentrations.

    PubMed

    Zhou, Chengjun; Lee, Sunyoung; Dooley, Kerry; Wu, Qinglin

    2013-12-15

    Porous nanocomposite gels were fabricated by a facile method consisting of the electrospinning and subsequent heat treatment based on partially hydrolyzed polyacrylamide (HPAM) of ultra-high molecular weight, with cellulose nanocrystals (CNCs) as crosslinker. The effects of three electrospinning parameters (i.e., solution concentration, composition of solvent mixture, and CNC loading level) on morphology and diameter of electrospun fibers were systematically investigated. The swelling properties of porous gels and their application in the removal of methylene blue dye (as a compound representative of contaminants) were evaluated. Electrospun fiber morphologies without beads, branches, and ribbons were achieved by optimizing the electrospinning solutions. The thermal crosslinking between HPAM and CNCs was realized through esterification, rendering the product nanocomposite membranes insoluble in water. Electrospun fibers of approximately 220 nm in diameter comprised the 3D porous nanocomposite gels, with porosity greater than 50%. The porous nanocomposite gels displayed a rapid swelling rate and an efficient adsorption capacity in removing methylene blue at low concentrations from aqueous solutions. PMID:23958139

  16. Glucose biosensor based on covalent immobilization of enzyme in sol-gel composite film combined with Prussian blue/carbon nanotubes hybrid.

    PubMed

    Fu, Guanglei; Yue, Xiuli; Dai, Zhifei

    2011-05-15

    A novel electrochemical glucose biosensor was developed based on in situ covalent immobilization of glucose oxidase (GOx) by one-pot chitosan (CS)-incorporated sol-gel process in the presence of Prussian blue deposited multi-walled carbon nanotubes hybrids (PB/MWNTs) using 3-isocyanatopropyltriethoxysilane (ICPTES) as both a sol-gel precursor and a covalent coupling agent for GOx and CS. The electrode modified with the PB/MWNTs-GOx-CS-ICPTES sol-gel composite film showed good electrical conductivity and effective low-potential electron transfer mediation toward H2O2 reduction attributed to the incorporation of PB/MWNTs. The biosensor exhibited a linear response to glucose in the concentration range from 2.5×10(-5) to 1.3×10(-3) M with a correlation coefficient of 0.9998, a detection limit of 7.5×10(-6) M, a low response time (10s ), good sensitivity and high anti-interference ability. Compared with the control biosensor based on the traditional tetraethoxysilane derived sol-gel composite film, the biosensor showed a similarly small apparent Michaelis-Menten constant of 3.67 mM but much higher electrochemical and biosensing stability. PMID:21478008

  17. Assessment of radiochromic gel dosimeter based on Turnbull Blue dye for relative output factor measurements of the Leksell Gamma Knife® PerfexionTM

    NASA Astrophysics Data System (ADS)

    Kozubikova, P.; Solc, J.; Novotny, J., Jr.; Pilarova, K.; Pipek, J.; Koncekova, J.

    2015-01-01

    The aim of the study was to perform assessment of radiochromic gel dosimeter based on Turnbull blue dye formed by irradiation (TB gel dosimeter) for measurement of ROFs for 4 mm and 8 mm collimators for the Leksell Gamma Knife PerfexionTM. All measurements have been carried out using home-made spherical Perspex glass phantom of diameter 160 mm. TB gel dosimeters were scanned using homemade optical CT scanner. The results are compared with vendor recommended Monte Carlo calculated ROFs values of 0.814 and 0.900 for 4 mm and 8 mm collimators, respectively. The comparisons between the gel measurements and the treatment planning system (TPS) calculation are presented in the form of 2D isodoses for the central slices and 1D profile. Measured ROF 0.746 and 0.874 for 4 mm and 8 mm collimators respectively are in a reasonable agreement with vendor recommended values and measured relative dose distribution in a central slice and measured profiles of all shots show excellent correspondence with TPS.

  18. Titanium dioxide-gold nanocomposite materials embedded in silicate sol-gel film catalyst for simultaneous photodegradation of hexavalent chromium and methylene blue.

    PubMed

    Pandikumar, Alagarsamy; Ramaraj, Ramasamy

    2012-02-15

    Aminosilicate sol-gel supported titanium dioxide-gold (EDAS/(TiO(2)-Au)(nps)) nanocomposite materials were synthesized by simple deposition-precipitation method and characterized. The photocatalytic oxidation and reduction activity of the EDAS/(TiO(2)-Au)(nps) film was evaluated using hexavalent chromium (Cr(VI)) and methylene blue (MB) dye under irradiation. The photocatalytic reduction of Cr(VI) to Cr(III) was studied in the presence of hole scavengers such as oxalic acid (OA) and methylene blue (MB). The photocatalytic degradation of MB was investigated in the presence and absence of Cr(VI). Presence of Au(nps) on the (TiO(2))(nps) surface and its dispersion in the silicate sol-gel film (EDAS/(TiO(2)-Au)(nps)) improved the photocatalytic reduction of Cr(VI) and oxidation of MB due to the effective interfacial electron transfer from the conduction band of the TiO(2) to Au(nps) by minimizing the charge recombination process when compared to the TiO(2) and (TiO(2)-Au)(nps) in the absence of EDAS. The EDAS/(TiO(2)-Au)(nps) nanocomposite materials provided beneficial role in the environmental remediation and purification process through synergistic photocatalytic activity by an advanced oxidation-reduction processes. PMID:22206972

  19. An antifungal peptide with antiproliferative activity toward tumor cells from red kidney beans.

    PubMed

    Li, Miao; Wang, Hexiang; Ng, Tzi Bun

    2011-06-01

    A 7.3-kDa antifungal peptide was purified from dried red kidney beans. The purification procedure entailed ion exchange chromatography on DEAE-cellulose, affinity chromatography on Affi-gel blue gel, ion exchange chromatography on CM-cellulose, followed by fast protein liquid chromatography-gel filtration on Superdex 75. The peptide was unadsorbed on DEAE-cellulose but adsorbed on Affi-gel blue gel and CM-cellulose. It exhibited a molecular mass of 7.3 kDa in gel filtration and also in SDS-polyacrylamide gel electrophoresis, indicating that it is a single-chained protein. The N-terminal sequence of the peptide was DGVCFGGLANGDRT. The peptide exerted an antifungal action on Fusarium oxysporum with an IC₅₀ of 3.8±0.4 µM (mean±SD, n=3). It also inhibited mycelial growth in Mycosphaerella arachidicola. It suppressed growth of lymphoma MBL2 cells and leukemia L1210 cells with an IC₅₀ of 5.2±0.4 µM and 7.6±0.6 µM, respectively. HIV-1 reverse transcriptase was inhibited with an IC₅₀ of 40±3.2 µM. However, no activity was demonstrated toward other viral enzymes. PMID:21309741

  20. Structural, Morphological, Vibrational, and Photoluminescence Study of Sol-Gel-Synthesized Tm3+:NaGd(WO4)2 Blue Phosphors

    NASA Astrophysics Data System (ADS)

    Durairajan, A.; Thangaraju, D.; Valente, M.; Moorthy Babu, S.

    2015-11-01

    The photoluminescence properties of sol-gel-derived NaGd1- x Tm x (WO4)2 sub-micron powders were studied. Formation of a crystalline material with a tetragonal structure and the I41/a space group was confirmed by powder x-ray diffraction measurements. The surface morphology and size distribution of the powders were investigated by scanning electron microscopy. Double tungstate formation was confirmed by Fourier-transform infrared and Raman spectroscopy and the corresponding vibrations were also assigned. A broad charge-transfer band (CTB) and intra-configurational 4f-4f transitions in the excitation spectra are discussed. Strong blue emission was observed at 455 nm (1D2 → 3F4) for both CTB and intra-configurational 4f-4f excitation bands, and strong emission as a result of intra-configurational 4f-4f excitation only was also observed. The concentration dependence of emission was studied, and emission was found to be maximum for x = 0.05. The corresponding critical distance was also determined and a mechanism is proposed for energy transfer by Tm3+ ions in the NaGd(WO4)2 matrix. The Commission International de l'Eclairage (CIE) coordinates were calculated and fell in the blue region of the CIE diagram. The coordinates of the blue intensity maximum were also matched with European Broadcasting Union standard values.

  1. Isolation of a new ribonuclease from fruiting bodies of the silver plate mushroom Clitocybe maxima.

    PubMed

    Wang, Hexiang; Ng, T B

    2004-06-01

    A ribonuclease, with an N-terminal sequence exhibiting some homology to ribonuclease from Pleurotus ostreatus (Family Pleurotaceae), has been purified from fruiting bodies of the silver plate mushroom Clitocybe maxima (Family Tricholomataceae). However, there is little resemblance between the N-terminal sequences of ribonucleases from various Pleurotus species, and a lesser extent of resemblance between ribonucleases from C. maxima and Pleurotus tuber-regium. No structural relationship exists between ribonuclease from C. maxima, and those from Volvariella volvacea, Lentinus edodes and Irpex lacteus. The purification protocol involved ion exchange chromatography on DEAE-cellulose, affinity chromatography on Affi-gel blue gel, ion exchange chromatography on CM-Sepharose, and fast protein liquid chromatography on Superdex 75. The ribonuclease was unadsorbed on DEAE-cellulose and adsorbed on Affi-gel blue gel and CM-Sepharose. It exhibited a molecular mass of 17.5 kDa in both gel filtration and sodium dodecyl sulfate-polyacrylamide gel electrophoresis. It manifested roughly the same ribonucleolytic potency toward poly A and poly G followed by poly U. Its activity toward poly C was, by comparison, meager. The temperature and pH required for its optimal activity were, respectively, 70 degrees C and 6.5-7.0. PMID:15203239

  2. Influence of acid chain length on the properties of TiO2 prepared by sol-gel method and LC-MS studies of methylene blue photodegradation.

    PubMed

    Bakre, Pratibha V; Volvoikar, Prajesh S; Vernekar, Amit A; Tilve, S G

    2016-07-15

    Nano-sized titanium dioxide photocatalysts were synthesized by hybrid hydrolytic nonhydrolytic sol-gel method using aliphatic organic acid templates to study the effect of chain length on their properties. X-ray diffraction pattern indicated crystalline anatase phase. The Barrett-Joyner-Halenda surface area measurement gave surface area ranging from 98.4 to 205.5m(2)/g and was found to be dependent on the chain length of the aliphatic acid. The longer chain acids rendered the material with high surface area. The organic acids acted as bidentate ligand and a surfactant in controlling the size and the mesoporosity. The size of the TiO2 nanoparticulate was found to be in the range of 10-18nm. The catalyst prepared by employing long chain acids octanoic acid and palmitic acid had smaller size, narrow pore radius, higher surface area and showed better photocatalytic activity than the commercially available Degussa P25 catalyst for the degradation of methylene blue dye. A new intermediate was identified by tandem liquid chromatography mass spectrometry studies during the degradation of methylene blue solution. PMID:27100905

  3. Purification and characterization of phytase with a wide pH adaptation from common edible mushroom Volvariella volvacea (Straw mushroom).

    PubMed

    Xu, Lijing; Zhang, Guoqing; Wang, Hexiang; Ng, Tzi Bun

    2012-02-01

    A novel phytase with a molecular mass of 14 kDa was isolated from fresh fruiting bodies of the common edible mushroom Volvariella volvacea (Straw mushroom). The isolation procedure involved successive chromatography on DEAE-cellulose, CM-cellulose, Affi-gel blue gel, Q-Sepharose and Superdex-75. The enzyme was a monomeric protein and was unadsorbed on DEAE-cellulose, CM-cellulose and Affi-gel blue gel, but was adsorbed on Q-Sepharose. The enzyme was purified 51.6-fold from the crude extract with 25.9% yield. Its N-terminal amino acid sequence GEDNEHDTQA exhibited low homology to the other reported phytases. The optimal pH and temperature of the purified enzyme was 5 and 45 degrees C, respectively. The enzyme was quite stable over the pH range of 3.0 to 9.0 with less than 30% change in its activity, suggesting that it can be used in a very wide pH range. The enzyme exhibited broad substrate selectivity towards various phosphorylated compounds, but lacked antifungal activity against tested plant pathogens. PMID:22435144

  4. pH sensor based on sol-gel silica layer deposited on a plastic optical fiber with blue bromophenol

    NASA Astrophysics Data System (ADS)

    Alvarado-Méndez, Edgar; Hernández-Cruz, Daniel; Rojas-Laguna, Roberto; Andrade-Lucio, Jose A.; Estudillo-Ayala, Julian M.; Trejo-Durán, M.; Ibarra-Manzano, Oscar G.; Ponce-Ballesteros, J. Erasmo; Lessard, Roger A.

    2004-11-01

    Design and characterization of a pH optical fiber sensor with a pH sensitive dye is described in this paper. TEOS (Tetra-ethyl-Orto-Silicate) was used to dope a plastic optical fiber, which will be used as the optical probe (OPTRODE). The sensor is prepared by fixing the doped plastic fiber on a fused ortosilica block surface with blue bromophenol. The fiber surface charged with silica modified the refractive index, which plays an important roll on the fiber, modifies the conditions of light propagation into the plastic optical fiber. The fiber transmittance is used to measure the pH of a solution or a fluid in a range between 4 and 7; such signal is captured by a photodetector and processed with a LabView program. The advantage of this system is that, 2cm of doped fiber are enough to measure the pH of a fluid in real time. The time response of the sensor reported in the present study is approximately 10s.

  5. The Goat (Capra hircus) Mammary Gland Mitochondrial Proteome: A Study on the Effect of Weight Loss Using Blue-Native PAGE and Two-Dimensional Gel Electrophoresis.

    PubMed

    Cugno, Graziano; Parreira, José R; Ferlizza, Enea; Hernández-Castellano, Lorenzo E; Carneiro, Mariana; Renaut, Jenny; Castro, Noemí; Arguello, Anastasio; Capote, Juan; Campos, Alexandre M O; Almeida, André M

    2016-01-01

    Seasonal weight loss (SWL) is the most important limitation to animal production in the Tropical and Mediterranean regions, conditioning producer's incomes and the nutritional status of rural communities. It is of importance to produce strategies to oppose adverse effects of SWL. Breeds that have evolved in harsh climates have acquired tolerance to SWL through selection. Most of the factors determining such ability are related to changes in biochemical pathways as affected by SWL. In this study, a gel based proteomics strategy (BN: Blue-Native Page and 2DE: Two-dimensional gel electrophoresis) was used to characterize the mitochondrial proteome of the secretory tissue of the goat mammary gland. In addition, we have conducted an investigation of the effects of weight loss in two goat breeds with different levels of adaptation to nutritional stress: Majorera (tolerant) and Palmera (susceptible). The study used Majorera and Palmera dairy goats, divided in 4 sets, 2 for each breed: underfed group fed on wheat straw (restricted diet, so their body weight would be 15-20% reduced by the end of experiment), and a control group fed with an energy-balanced diet. At the end of the experimental period (22 days), mammary gland biopsies were obtained for all experimental groups. The proteomic analysis of the mitochondria enabled the resolution of a total of 277 proteins, and 148 (53%) were identified by MALDI-TOF/TOF mass spectrometry. Some of the proteins were identified as subunits of the glutamate dehydrogenase complex and the respiratory complexes I, II, IV, V from mitochondria, as well as numerous other proteins with functions in: metabolism, development, localization, cellular organization and biogenesis, biological regulation, response to stimulus, among others, that were mapped in both BN and 2DE gels. The comparative proteomics analysis enabled the identification of several proteins: NADH-ubiquinone oxidoreductase 75 kDa subunit and lamin B1 mitochondrial (up

  6. The Goat (Capra hircus) Mammary Gland Mitochondrial Proteome: A Study on the Effect of Weight Loss Using Blue-Native PAGE and Two-Dimensional Gel Electrophoresis

    PubMed Central

    Cugno, Graziano; Parreira, José R.; Ferlizza, Enea; Hernández-Castellano, Lorenzo E.; Carneiro, Mariana; Renaut, Jenny; Castro, Noemí; Arguello, Anastasio; Capote, Juan

    2016-01-01

    Seasonal weight loss (SWL) is the most important limitation to animal production in the Tropical and Mediterranean regions, conditioning producer’s incomes and the nutritional status of rural communities. It is of importance to produce strategies to oppose adverse effects of SWL. Breeds that have evolved in harsh climates have acquired tolerance to SWL through selection. Most of the factors determining such ability are related to changes in biochemical pathways as affected by SWL. In this study, a gel based proteomics strategy (BN: Blue-Native Page and 2DE: Two-dimensional gel electrophoresis) was used to characterize the mitochondrial proteome of the secretory tissue of the goat mammary gland. In addition, we have conducted an investigation of the effects of weight loss in two goat breeds with different levels of adaptation to nutritional stress: Majorera (tolerant) and Palmera (susceptible). The study used Majorera and Palmera dairy goats, divided in 4 sets, 2 for each breed: underfed group fed on wheat straw (restricted diet, so their body weight would be 15–20% reduced by the end of experiment), and a control group fed with an energy-balanced diet. At the end of the experimental period (22 days), mammary gland biopsies were obtained for all experimental groups. The proteomic analysis of the mitochondria enabled the resolution of a total of 277 proteins, and 148 (53%) were identified by MALDI-TOF/TOF mass spectrometry. Some of the proteins were identified as subunits of the glutamate dehydrogenase complex and the respiratory complexes I, II, IV, V from mitochondria, as well as numerous other proteins with functions in: metabolism, development, localization, cellular organization and biogenesis, biological regulation, response to stimulus, among others, that were mapped in both BN and 2DE gels. The comparative proteomics analysis enabled the identification of several proteins: NADH-ubiquinone oxidoreductase 75 kDa subunit and lamin B1 mitochondrial (up

  7. Reduction of 3-keto-5 beta-cholanoic acid to lithocholic and isolithocholic acids by human liver cytosol in vitro.

    PubMed

    Amuro, Y; Yamade, W; Maebo, A; Hada, T; Higashino, K

    1985-10-23

    The formation of lithocholic and isolithocholic acids from 3-keto-5 beta-cholanoic acid by human liver cytosol was examined in vitro. Liver cytosol was incubated at various pH levels with 3-keto-5 beta-cholanoic acid in a phosphate buffer containing NADPH or NADH; the products formed were analyzed by gas chromatography. Results showed that human liver cytosol reduced 3-keto-5 beta-cholanoic acid to lithocholic acid at a pH level of 7.0 or above and to isolithocholic acid at a pH level of 6.0 or below when NADPH was used as a coenzyme, and it was reduced to isolithocholic acid only when NADH was used. Furthermore, two peaks for the reducing enzymes could be clearly found by column chromatography of Affi-Gel Blue. These results indicate that human liver cytosol contains two enzymes acting on reduction of 3-keto-5 beta-cholanoic acid to lithocholic and isolithocholic acids, which are dependent on the pH level and the use of NADPH or NADH in vitro. Since the 3 beta-dehydrogenation was inhibited by the addition of pyrazole, an alcohol dehydrogenase inhibitor or ethanol, and the major peak of 3 beta-hydroxysteroid dehydrogenase coincided with the peak of alcohol dehydrogenase on Affi-Gel Blue chromatography, at least some of the cytosolic 3 beta-hydroxysteroid dehydrogenase seemed to be identical to or to have characteristics similar to alcohol dehydrogenase. PMID:2932163

  8. Sativin: a novel antifungal miraculin-like protein isolated from legumes of the sugar snap Pisum sativum var. macrocarpon.

    PubMed

    Ye, X Y; Wang, H X; Ng, T B

    2000-07-01

    An antifungal protein designated sativin was isolated from the legumes of the sugar snap (also known as honey pea) Pisum sativum var. macrocarpon. The procedure entailed extraction, affinity chromatography on Affi-gel blue gel and ion exchange chromatography on CM-Sepharose. The protein exhibited a molecular weight of 38 kDa in SDS-polyacrylamide gel electrophoresis. It possessed an N-terminal amino acid sequence which showed similarity to those of miraculin (a sweet protein) and pisavin (a ribosome-inactivating protein from Pisum sativum var arvense Poir manifesting similarity to miraculin). Unlike pisavin, however, sativin demonstrated negligible ribonuclease activity and inhibited translation in a rabbit reticulocyte lysate system with a very low potency (IC50= 14 microM). Sativin exerted antifungal activity against Fusarium oxysporum, Coprinus comatus and Pleurotus ostreatus but not against Rhizoctonia solani. PMID:10968407

  9. Vulgarinin, a broad-spectrum antifungal peptide from haricot beans (Phaseolus vulgaris).

    PubMed

    Wong, Jack Ho; Ng, Tzi Bun

    2005-08-01

    From the seeds of haricot beans (Phaseolus vulgaris), an antifungal peptide with a molecular mass around 7 kDa was purified by using a simple protocol consisting of affinity chromatography on Affi-gel blue gel and gel filtration on Superdex 75. This peptide named vulgarinin manifested an antifungal activity toward fungal species such as Fusarium oxysporum, Mycosphaerella arachidicola, Physalospora piricola and Botrytis cinerea, and an antibacterial action on Mycobacterium phlei, Bacillus megaterium, Bacillus subtilis and Proteus vulgaris. It also inhibited proliferation in leukemia cell lines L1210 and M1 and breast cancer cell line MCF-7. This peptide could reduce the activity of HIV-1 reverse transcriptase and inhibited translation in a cell-free rabbit reticulocyte lysate system. Its antifungal activity was retained after incubation with trypsin. PMID:15896669

  10. Lunatusin, a trypsin-stable antimicrobial peptide from lima beans (Phaseolus lunatus L.).

    PubMed

    Wong, Jack Ho; Ng, Tzi Bun

    2005-11-01

    An anti-fungal peptide designated as lunatusin, with a molecular mass around 7kDa, was purified from the seeds of Chinese lima bean (Phaseolus lunatus L.). The peptide was isolated using a simple protocol consisting of affinity chromatography on Affi-gel blue gel and gel filtration on Superdex 75. Lunatusin exerted an anti-fungal activity toward fungal species such as Fusarium oxysporum, Mycosphaerella arachidicola and Botrytis cinerea, and an antibacterial action on, Bacillus megaterium, Bacillus subtilis, Proteus vulgaris and Mycobacterium phlei. It also inhibited proliferation in the breast cancer cell line MCF-7. Lunatusin reduced the activity of HIV-1 reverse transcriptase and it also inhibited translation in a cell-free rabbit reticulocyte lysate system. Its anti-fungal activity was retained after incubation with trypsin. Lunatusin elicited a mitogenic response from mouse splenocytes. PMID:16269344

  11. Isolation of a homodimeric lectin with antifungal and antiviral activities from red kidney bean (Phaseolus vulgaris) seeds.

    PubMed

    Ye, X Y; Ng, T B; Tsang, P W; Wang, J

    2001-07-01

    A homodimeric lectin adsorbed on Affi-gel blue gel and CM-Sepharose and possessing a molecular weight of 67 kDa was isolated from red kidney beans. The hemagglutinating activity of this lectin was inhibited by glycoproteins but not by simple sugars. The lectin manifested inhibitory activity on human immunodeficiency virus-1 reverse transcriptase and alpha-glucosidase. The N-terminal sequence of the lectin exhibited some differences from previously reported lectins from Phaseolus vulgaris but showed some similarity to chitinases. It exerted a suppressive effect on growth of the fungal species Fusarium oxysporum, Coprinus comatus, and Rhizoctonia solani. The lectin had low ribonuclease and negligible translation-inhibitory activities. PMID:11732688

  12. Sesquin, a potent defensin-like antimicrobial peptide from ground beans with inhibitory activities toward tumor cells and HIV-1 reverse transcriptase.

    PubMed

    Wong, Jack Ho; Ng, Tzi Bun

    2005-07-01

    An antifungal peptide with a molecular mass around 7 kDa and an N-terminal sequence highly homologous to defensin was isolated from ground beans (Vigna sesquipedalis cv. 'Ground Bean'). The peptide was adsorbed on Affi-gel blue gel and on Mono S. It exerted an antifungal action on Botrytis cinerea, Fusarium oxysporum and Mycosphaerella arachidicola; and an antibacterial action on Escherichia coli B, Proteus vulgaris, Mycobacterium phlei and Bacillus megaterium. The antimicrobial activity was inhibited in presence of the 5 mM CaCl2 and MgCl2, but no inhibition was observed in 5 mM NaCl. The peptide exerted antiproliferative activity toward breast cancer (MCF-7) cells and leukemia M1 cells, this activity could not be inhibited by the ions mentioned above. It also exhibited some inhibitory activity toward human immunodeficiency virus-type 1 reverse transcriptase. PMID:15949629

  13. Tungsten oxide buffer layers fabricated in an inert sol-gel process at room-temperature for blue organic light-emitting diodes.

    PubMed

    Höfle, Stefan; Bruns, Michael; Strässle, Stefan; Feldmann, Claus; Lemmer, Uli; Colsmann, Alexander

    2013-08-14

    WO3 deposition from tungsten ethoxide precursor solutions at room temperature is demonstrated. The W(OEt)6 precursor can be converted under inert conditions and hence avoids sample contamination with oxygen, opening a pathway to more stable devices. The stoichiometry of all WO3 layers and the optoelectronic performance of the respective SMOLEDs well match thermally evaporated WO3 and its corresponding SMOLEDs. The solution processed WO3 hole injection layers enable the fabrication of blue phosphorescent OLEDs with low onset voltage and current efficiencies of up to 14 cd A(-1) . PMID:23813694

  14. Evidence for a dissociable protein subunit required for calmodulin stimulation of brain adenylate cyclase.

    PubMed Central

    Toscano, W A; Westcott, K R; LaPorte, D C; Storm, D R

    1979-01-01

    An adenylate cyclase [ATP pyrophosphatelyase (cyclizing), EC 4.6.1.1] preparation that is not stimulated by NaF,5'-guanylyl imidodiphosphate, or Ca2+.calmodulin has been isolated from bovine cerebral cortex by Affi-Gel Blue chromatography and calmodulin-Sepharose chromatography. Sensitivity to these effectors was restored by incubation of the adenylate cyclase preparation with detergent-solubilized protein from bovine cerebral cortex. Reconstitution of of Ca2+.calmodulin activation required the presence of 5'-guanylyl imidodiphosphate. The factor required for restoration of Ca2+.calmodulin stimulation was sensitive to heat, trypsin digestion, and N-ethylmaleimide. These observations suggest that this adenylate cyclase activity requires the presence of one or more guanyl nucleotide binding subunits for calmodulin sensitivity. PMID:293663

  15. Intense pulsed light versus photodynamic therapy using liposomal methylene blue gel for the treatment of truncal acne vulgaris: a comparative randomized split body study.

    PubMed

    Moftah, Nayera Hassan; Ibrahim, Shady Mahmoud; Wahba, Nadine Hassan

    2016-05-01

    Acne vulgaris is an extremely common skin condition. It often leads to negative psychological consequences. Photodynamic therapy (PDT) using intense pulsed light has been introduced for effective treatment of acne. The objective was to study the effect of PDT in truncal acne vulgaris using liposomal methylene blue (LMB) versus IPL alone. Thirty-five patients with varying degrees of acne were treated with topical 0.1 % LMB hydrogel applied on the randomly selected one side of the back, and after 60 min the entire back was exposed to IPL. The procedure was done once weekly for three sessions and patients were re-evaluated 1 month after the third session by two independent dermatologists. Acne severity was graded using the Burton scale. Patient satisfaction using Cardiff Acne Disability Index (CADI) was recorded before and after treatment. On LMB-pretreated side, inflammatory acne lesion counts were significantly decreased by 56.40 % compared with 34.06 % on IPL alone. Marked improvement was seen on LMB-pretreated side in 11.5 % of patients compared with 2.8 % on IPL alone. There was a correlation between CADI score and overall improvement. Our study concluded that LMB-IPL is more effective than IPL alone, safe with tolerable pain in the treatment of acne vulgaris on the back. LMB-IPL is more effective than IPL alone, safe with tolerable pain in the treatment of acne vulgaris on the back. PMID:26993345

  16. Structural and photoluminescent properties of nanosized BaMgAl10O17:Eu2+ blue-emitting phosphors prepared by sol-gel method

    NASA Astrophysics Data System (ADS)

    Van Bui, Hao; Nguyen, Tu; Nguyen, Manh Cuong; Tran, Trong An; Le Tien, Ha; Tam Tong, Hao; Nguyen, Thi Kim Lien; Pham, Thanh Huy

    2015-09-01

    We report on the photoluminescent properties of Ba0.9Eu0.1MgAl10O17 (BAM) phosphors in correlation with the host crystalline structures. The phosphors were synthesized by citrate sol-gel process, followed by a sintering and a reduction step, both at elevated temperatures. We found that the phosphors were amorphous when sintered at temperatures below 900 °C. At 1000 °C, the crystalline structure was mainly that of BaAl2O4 phase. The BaMgAl10O17 phase appeared at 1100 °C, and became dominant with increasing temperature. At 1300 °C, the BaAl2O4 phase almost disappeared, and only BaMgAl10O17 features were found. The luminescent characteristics of the phosphors were closely related to the structures of the host lattice. Under the same reduction conditions, the phosphors sintered at 1000 °C showed the emission of both Eu3+ and Eu2+. For the phosphors sintered at higher temperatures, the main features were originated from the emission of Eu2+. We additionally observed the increase of emission intensity and the broadening of emission spectra with increasing reduction temperature.

  17. Blue Note

    ScienceCinema

    Murray Gibson

    2010-01-08

    Argonne's Murray Gibson is a physicist whose life's work includes finding patterns among atoms. The love of distinguishing patterns also drives Gibson as a musician and Blues enthusiast."Blue" notes are very harmonic notes that are missing from the equal temperament scale.The techniques of piano blues and jazz represent the melding of African and Western music into something totally new and exciting.

  18. Blue Note

    SciTech Connect

    Murray Gibson

    2007-04-27

    Argonne's Murray Gibson is a physicist whose life's work includes finding patterns among atoms. The love of distinguishing patterns also drives Gibson as a musician and Blues enthusiast."Blue" notes are very harmonic notes that are missing from the equal temperament scale.The techniques of piano blues and jazz represent the melding of African and Western music into something totally new and exciting.

  19. Blue gods, blue oil, and blue people.

    PubMed

    Fairbanks, V F

    1994-09-01

    Studies of the composition of coal tar, which began in Prussia in 1834, profoundly affected the economies of Germany, Great Britain, India, and the rest of the world, as well as medicine and surgery. Such effects include the collapse of the profits of the British indigo monopoly, the growth in economic power of Germany based on coal tar chemistry, and an economic crisis in India that led to more humane tax laws and, ultimately, the independence of India and the end of the British Empire. Additional consequences were the development of antiseptic surgery and the synthesis of a wide variety of useful drugs that have eradicated infections and alleviated pain. Many of these drugs, particularly the commonly used analgesics, sulfonamides, sulfones, and local anesthetics, are derivatives of aniline, originally called "blue oil" or "kyanol." Some of these aniline derivatives, however, have also caused aplastic anemia, agranulocytosis, and methemoglobinemia (that is, "blue people"). Exposure to aniline drugs, particularly when two or three aniline drugs are taken concurrently, seems to be the commonest cause of methemoglobinemia today. PMID:8065194

  20. Isolation of a Glucosamine Binding Leguminous Lectin with Mitogenic Activity towards Splenocytes and Anti-Proliferative Activity towards Tumor Cells

    PubMed Central

    Chan, Yau Sang; Wong, Jack Ho; Fang, Evandro Fei; Pan, Wenliang; Ng, Tzi Bun

    2012-01-01

    A dimeric 64-kDa glucosamine-specific lectin was purified from seeds of Phaseolus vulgaris cv. “brown kidney bean.” The simple 2-step purification protocol involved affinity chromatography on Affi-gel blue gel and gel filtration by FPLC on Superdex 75. The lectin was absorbed on Affi-gel blue gel and desorbed using 1M NaCl in the starting buffer. Gel filtration on Superdex 75 yielded a major absorbance peak that gave a single 32-kDa band in SDS-PAGE. Hemagglutinating activity was completely preserved when the ambient temperature was in the range of 20°C–60°C. However, drastic reduction of the activity occurred at temperatures above 65°C. Full hemagglutinating activity of the lectin was observed at an ambient pH of 3 to 12. About 50% activity remained at pH 0–2, and only residual activity was observed at pH 13–14. Hemagglutinating activity of the lectin was inhibited by glucosamine. The brown kidney bean lectin elicited maximum mitogenic activity toward murine splenocytes at 2.5 µM. The mitogenic activity was nearly completely eliminated in the presence of 250 mM glucosamine. The lectin also increased mRNA expression of the cytokines IL-2, TNF-α and IFN-γ. The lectin exhibited antiproliferative activity toward human breast cancer (MCF7) cells, hepatoma (HepG2) cells and nasopharyngeal carcinoma (CNE1 and CNE2) cells with IC50 of 5.12 µM, 32.85 µM, 3.12 µM and 40.12 µM respectively after treatment for 24 hours. Flow cytometry with Annexin V and propidum iodide staining indicated apoptosis of MCF7 cells. Hoechst 33342 staining also indicated formation of apoptotic bodies in MCF7 cells after exposure to brown kidney bean lectin. Western blotting revealed that the lectin-induced apoptosis involved ER stress and unfolded protein response. PMID:22720002

  1. Polyelectrolyte gels

    SciTech Connect

    Segalman, D.J.; Witkowski, W.R.

    1995-06-01

    Polyelectrolyte (PE) gels are swollen polymer/solvent networks that undergo a reversible volume collapse/expansion through various types of stimulation. Applications that could exploit this large deformation and solvent expulsion/absorption characteristics include robotic {open_quotes}fingers{close_quotes} and drug delivery systems. The goals of the research were to first explore the feasibility of using the PE gels as {open_quotes}smart materials{close_quotes} - materials whose response can be controlled by an external stimulus through a feedback mechanism. Then develop a predictive capability to simulate the dynamic behavior of these gels. This involved experimentally characterizing the response of well-characterized gels to an applied electric field and other stimuli to develop an understanding of the underlying mechanisms which cause the volume collapse. Lastly, the numerical analysis tool was used to simulate various potential engineering devices based on PE gels. This report discusses the pursuit of those goals through experimental and computational means.

  2. Purification and characterization of a serine protease with fibrinolytic activity from Tenodera sinensis (praying mantis).

    PubMed

    Hahn, B S; Cho, S Y; Wu, S J; Chang, I M; Baek, K; Kim, Y C; Kim, Y S

    1999-03-19

    Mantis egg fibrolase (MEF) was purified from the egg cases of Tenodera sinensis using ammonium sulfate fractionation, gel filtration on Bio-Gel P-60 and affinity chromatography on DEAE Affi-Gel blue gel. The protease was assessed homogeneous by SDS-polyacrylamide gel electrophoresis and has a molecular mass of 31500 Da. An isoelectric point of 6.1 was determined by isoelectric focusing. Amino acid sequencing of the N-terminal region established a primary structure composed of Ala-Asp-Val-Val-Gln-Gly-Asp-Ala-Pro-Ser. MEF readily digested the Aalpha- and Bbeta-chains of fibrinogen and more slowly the gamma-chain. The nonspecific action of the enzyme results in extensive hydrolysis of fibrinogen and fibrin releasing a variety of fibrinopeptide. The enzyme is inactivated by Cu2+ and Zn2+ and inhibited by PMSF and chymostatin, yet elastinal, aprotinin, TLCK, TPCK, EDTA, EGTA, cysteine, beta-mercaptoethanol, iodoacetate, E64, benzamidine and soybean trypsin inhibitor do not affect activity. Antiplasmin was not sensitive to MEF but antithrombin III inhibited the enzymatic activity of MEF. Among chromogenic protease substrates, the most sensitive to MEF hydrolysis was benzoyl-Phe-Val-Arg-p-nitroanilide with maximal activity at pH 7.0 and 30 degrees C. MEF preferentially cleaved the oxidized B-chain of insulin between Leu15 and Tyr16. D-Dimer concentrations increased on incubation of cross-linked fibrin with MEF, indicating the enzyme has a strong fibrinolytic activity. PMID:10082965

  3. Visualising DNA in Classrooms Using Nile Blue

    ERIC Educational Resources Information Center

    Milne, Christine; Roche, Scott; McKay, David

    2008-01-01

    Giving students the opportunity to extract, manipulate and visualise DNA molecules enhances a constructivist approach to learning about modern techniques in biology and biotechnology Visualisation usually requires agarose gel electrophoresis and staining. In this article, we report on an alternative DNA stain, Nile Blue A, that may be used in the…

  4. A novel and potent ribonuclease from fruiting bodies of the mushroom Pleurotus pulmonarius.

    PubMed

    Ye, X Y; Ng, T B

    2002-05-01

    A ribonuclease (RNase), with an N-terminal sequence different from those of ribonucleases from the mushrooms Irpex lacteus, Lentinus edodes, Pleurotus ostreatus, Pleurotus tuber-regium, and Volvariella volvacea, was purified from fruiting bodies of the edible mushroom Pleurotus pulmonarius. The N-terminal sequence of P. pulmonarius RNase manifested homology to a portion of the sequences of ribosome inactivating protein abrin-b, abrin-c, and abrin-d, and Bacillus subtilis transcriptional regulator. The ribonuclease was adsorbed on Affi-gel blue gel, CM-Sepharose, and Mono S. It displayed a molecular mass of 14.4 kDa in both sodium dodecyl sulfate-polyacrylamide gel electrophoresis and gel filtration on Superdex 75. The ribonuclease exhibited an activity of 25 114 U/mg on yeast tRNA. The highest ribonucleolytic activity was demonstrated toward poly C, followed by poly A, and then by poly G. There was no activity toward poly U. The optimal pH for its activity was 7 and the optimal temperature was 55 degrees C. It inhibited cell-free translation in a rabbit reticulocyte lysate with an IC50 of 0.33 nM. PMID:12054550

  5. The Blue Bottle Revisited.

    ERIC Educational Resources Information Center

    Vandaveer, Walter R., IV; Mosher, Mel

    1997-01-01

    Presents a modification of the classic Blue Bottle demonstration that involves the alkaline glucose reduction of methylene blue. Uses other indicators in the classic Blue Bottle to produce a rainbow of colors. (JRH)

  6. Purification and Characterization of a Lectin from Phaseolus vulgaris cv. (Anasazi Beans)

    PubMed Central

    Sharma, Arishya; Ng, Tzi Bun; Wong, Jack Ho; Lin, Peng

    2009-01-01

    A lectin has been isolated from seeds of the Phaseolus vulgaris cv. “Anasazi beans” using a procedure that involved affinity chromatography on Affi-gel blue gel, fast protein liquid chromatography (FPLC)-ion exchange chromatography on Mono S, and FPLC-gel filtration on Superdex 200. The lectin was comprised of two 30-kDa subunits with substantial N-terminal sequence similarity to other Phaseolus lectins. The hemagglutinating activity of the lectin was stable within the pH range of 1–14 and the temperature range of 0–80°C. The lectin potently suppressed proliferation of MCF-7 (breast cancer) cells with an IC50 of 1.3 μM, and inhibited the activity of HIV-1 reverse transcriptase with an IC50 of 7.6 μM. The lectin evoked a mitogenic response from murine splenocytes as evidenced by an increase in [3H-methyl]-thymidine incorporation. The lectin had no antifungal activity. It did not stimulate nitric oxide production by murine peritoneal macrophages. Chemical modification results indicated that tryptophan was crucial for the hemagglutinating activity of the lectin. PMID:19343172

  7. A hemagglutinin with mitogenic activity from dark red kidney beans.

    PubMed

    Xia, Lixin; Ng, T B

    2006-12-01

    A 67-kDa hemagglutinin composed of two identical subunits was purified from Phaseolus vulgaris cv. 'Dark Red Kidney Bean'. It was unadsorbed on DEAE-cellulose but adsorbed on Affi-gel blue gel. The hemagglutinin was highly purified after the two aforementioned chromatographic steps as revealed by a single peak in gel filtration on Superdex 75 and a single band in SDS-PAGE. The hemagglutinating activity was stable between 25 degrees C and 70 degrees C, and between pH 4 and pH 11, and in the presence of a variety of divalent metal chlorides at 500 mM concentration. The activity was reduced by 50% at 80 degrees C, and also when the pH was lowered to 3 or elevated to 12. The activity was reduced by 75% in the presence of 250 mM KCl or NaCl. A variety of sugars tested failed to inhibit the hemagglutinating activity of the hemagglutinin. Although the hemagglutinin exhibited mitogenic activity toward murine splenocytes, it had no effect on the activity of HIV-1 reverse transcriptase or mycelial growth in the fungi Botrytis cinerea, Fusarium oxysporum and Mycosphaerella arachidicola. It exerted an antiproliferative activity on leukemia L1210 cells. PMID:16945595

  8. Hemagglutinating activity of proteins from Parkia speciosa seeds.

    PubMed

    Chankhamjon, Kanokwan; Petsom, Amorn; Sawasdipuksa, Narumon; Sangvanich, Polkit

    2010-01-01

    Proteins from Parkia speciosa Hassk. (Fabaceae) seeds were extracted and stepwise precipitated using ammonium sulfate. Proteins precipitated with 25% ammonium sulfate were separated by affinity chromatography on Affi-Gel Blue gel followed by protein liquid chromatography on Superdex 200. The protein Gj, which was identified as a protein similar to putative aristolochene synthase, 3'-partial from Oryza sativa L. (Poaceae), had hemagglutinating activity of 0.39 mug/muL. Moreover, fraction C2 from the proteins precipitated with 60% ammonium sulfate, separated by lectin-specific adsorption chromatography using Con A Sepharose, had hemagglutinating activity of 1.17 mug/muL. Using gel electrophoresis, two proteins C2a and C2b were separated, having molecular weights of 45 kDa and 23 kDa, respectively. From protein identification, C2a was found to be similar to the hypothetical protein B1342F01.11 from Oryza sativa, and C2b was similar to the hypothetical protein At1g51560 from Arabidopsis thaliana (L.) Heynh. (Brassicaceae). PMID:20645760

  9. Novel antifungal peptides from Ceylon spinach seeds.

    PubMed

    Wang, H; Ng, T B

    2001-11-01

    Two novel antifungal peptides, designated alpha- and beta-basrubrins, respectively, were isolated from seeds of the Ceylon spinach Basella rubra. The purification procedure involved saline extraction, (NH(4))(2)SO(4) precipitation, ion exchange chromatography on DEAE-cellulose, affinity chromatography on Affi-gel blue gel, ion exchange chromatography on CM-cellulose and FPLC-gel filtration on Superdex peptide column. alpha- and beta-basrubrins exhibited a molecular weight of 4.3 and 5 kDa, respectively. They inhibited translation in a rabbit reticulocyte system with an IC(50) value of 400 and 100 nM, respectively. alpha- and beta-basrubrin inhibited HIV-1 reverse transcriptase by (79.4 +/- 7.8)% and (54.6 +/- 3.6)%, respectively, at a concentration of 400 microM, and (10.56 +/- 0.92)% and (2.12 +/- 0.81)%, respectively, at a concentration of 40 microM. Both alpha- and beta-basrubrins exerted potent antifungal activity toward Botrytis cinerea, Mycosphaerella arachidicola, and Fusarium oxysporum. PMID:11688973

  10. Trypsin Isoinhibitors with Antiproliferative Activity toward Leukemia Cells from Phaseolus vulgaris cv “White Cloud Bean”

    PubMed Central

    Sun, Jian; Wang, Hexiang; Ng, Tzi Bun

    2010-01-01

    A purification protocol that comprised ion exchange chromatography on DEAE-cellulose, affinity chromatography on Affi-gel blue gel, ion exchange chromatography on SP-Sepharose, and gel filtration by FPLC on Superdex 75 was complied to isolate two trypsin inhibitors from Phaseolus vulgaris cv “White Cloud Bean”. Both trypsin inhibitors exhibited a molecular mass of 16 kDa and reduced the activity of trypsin with an IC50 value of about 0.6 μM. Dithiothreitol attenuated the trypsin inhibitory activity, signifying that an intact disulfide bond is indispensable to the activity. [Methyl-3H] thymidine incorporation by leukemia L1210 cells was inhibited with an IC50 value of 28.8 μM and 21.5 μM, respectively. They were lacking in activity toward lymphoma MBL2 cells and inhibitory effect on HIV-1 reverse transcriptase and fungal growth when tested up to 100 μM. PMID:20617140

  11. A Phytase Characterized by Relatively High pH Tolerance and Thermostability from the Shiitake Mushroom Lentinus edodes

    PubMed Central

    Zhang, Guo-Qing; Wu, Ying-Ying; Ng, Tzi-Bun; Chen, Qing-Jun; Wang, He-Xiang

    2013-01-01

    A monomeric phytase with a molecular mass of 14 kDa was acquired from fresh fruiting bodies of the shiitake mushroom Lentinus edodes. The isolation procedure involved chromatography on DEAE-cellulose, CM-cellulose, Q-Sepharose, Affi-gel blue gel, and a final fast protein liquid chromatography-gel filtration on Superdex 75. The purified phytase demonstrated the unique N-terminal amino acid sequence DPKRTDQVN, which exhibited no sequence similarity with those of other phytases previously reported. It expressed its maximal activity at pH 5.0 and 37°C. Phytase activity manifested less than 20% change in activity over the pH range of 3.0–9.0, considerable thermostability with more than 60% residual activity at 70°C, and about 40% residual activity at 95°C. It displayed a wide substrate specificity on a variety of phosphorylated compounds with the following ranking: ATP > fructose-6-phosphate > AMP > glucose-6-phosphate > ADP > sodium phytate > β-glycerophosphate. The phytase activity was moderately stimulated by Ca2+, but inhibited by Al3+, Mn2+, Zn2+, and Cu2+ at a tested concentration of 5 mM. PMID:23586045

  12. A Glucosamine-Specific Lectin from Green Dragon No. 8 Beans (Phaseolus vulgaris) Induced Apoptosis on Nasopharyngeal Carcinoma Cells

    PubMed Central

    Chan, Yau Sang; Xia, Lixin; Ng, Tzi Bun

    2015-01-01

    A lectin exhibiting antiproliferative activity on tumor cell lines but devoid of antifungal activity has been purified from Phaseolus vulgaris cv. Green Dragon no. 8 seeds. The lectin was a 60 kDa dimeric protein with two 30 kDa subunits. It was a glucosamine-specific lectin as implied from the inhibitory effect of glucosamine on hemagglutinating activity of the lectin. The steps for isolation of the lectin involved Affi-gel blue gel (affinity gel), Mono Q (anion exchanger), and Superdex 75 column (size exclusion). The lectin was purified 20.8-fold from the crude extract of the beans. The purified lectin showed antiproliferative activity on breast cancer MCF7 cell line and nasopharyngeal cancer HONE1 and CNE2 cell lines, but a low activity on normal skin fibroblast HSF98 cell line. The lectin was shown to induce apoptosis on HONE1 cells, as indicated by increased phosphatidylserine externalization and mitochondrial depolarization. It also blocked HONE1 cell division and kept the cells at the G2/M phase of the cell cycle. PMID:26290674

  13. Aerosol gels

    NASA Technical Reports Server (NTRS)

    Sorensen, Christopher M. (Inventor); Chakrabarti, Amitabha (Inventor); Dhaubhadel, Rajan (Inventor); Gerving, Corey (Inventor)

    2010-01-01

    An improved process for the production of ultralow density, high specific surface area gel products is provided which comprises providing, in an enclosed chamber, a mixture made up of small particles of material suspended in gas; the particles are then caused to aggregate in the chamber to form ramified fractal aggregate gels. The particles should have a radius (a) of up to about 50 nm and the aerosol should have a volume fraction (f.sub.v) of at least 10.sup.-4. In preferred practice, the mixture is created by a spark-induced explosion of a precursor material (e.g., a hydrocarbon) and oxygen within the chamber. New compositions of matter are disclosed having densities below 3.0 mg/cc.

  14. A novel smart supramolecular organic gelator exhibiting dual-channel responsive sensing behaviours towards fluoride ion via gel-gel states.

    PubMed

    Mehdi, Hassan; Pang, Hongchang; Gong, Weitao; Dhinakaran, Manivannan Kalavathi; Wajahat, Ali; Kuang, Xiaojun; Ning, Guiling

    2016-07-01

    A novel smart supramolecular organic gelator G-16 containing anion and metal-coordination ability has been designed and synthesized. It shows excellent and robust gelation capability as a strong blue fluorescent supramolecular organic gel OG in DMF. Addition of Zn(2+) produced Zn(2+)-coordinated supramolecular metallogel OG-Zn. Organic gel OG and organometallic gel OG-Zn exhibited efficient and different sensing behaviors towards fluoride ion due to the variation in self-assembling nature. Supramolecular metallogel OG-Zn displayed specific selectivity for fluoride ion and formed OG-Zn-F with dramatic color change from blue to blue green in solution and gel to gel states. Furthermore after directly addition of fluoride into OG produced fluoride containing organic gel OG-F with drastically modulation in color from blue to greenish yellow fluorescence via strong aggregation-induced emission (AIE) property. A number of experiments were conducted such as FTIR, (1)H NMR, and UV/Vis spectroscopies, XRD, SEM and rheology. These results revealed that the driving forces involved in self-assembly of OG, OG-Zn, OG-Zn-F and OG-F were hydrogen bonding, metal coordination, π-π interactions, and van der Waal forces. In contrast to the most anion responsive gels, particularly fluoride ion responsive gels showed gel-sol state transition on stimulation by anions, the gel state of OG and OG-Zn did not show any gel-to-sol transition during the whole F(-) response process. PMID:27193611

  15. Structure and Activity Changes of Phytohemagglutinin from Red Kidney Bean (Phaseolus vulgaris) Affected by Ultrahigh-Pressure Treatments.

    PubMed

    Lu, Yunjun; Liu, Cencen; Zhao, Mouming; Cui, Chun; Ren, Jiaoyan

    2015-11-01

    Phytohemagglutin (PHA), purified from red kidney beans (Phaseolus vulgaris) by Affi-Gel blue affinity chromatography, was subjected to ultrahigh-pressure (UHP) treatment (150, 250, 350, and 450 MPa). The purified PHA lost its hemagglutination activity after 450 MPa treatment and showed less pressure tolerance than crude PHA. However, the saccharide specificity and α-glucosidase inhibition activity of the purified PHA did not change much after UHP treatment. Electrophoresis staining by periodic acid-Schiff (PAS) manifested that the glycone structure of purified PHA remained stable even after 450 MPa pressure treatment. However, electrophoresis staining by Coomassie Blue as well as circular dichroism (CD) and differential scanning calorimetry (DSC) assay proved that the protein unit structure of purified PHA unfolded when treated at 0-250 MPa but reaggregates at 250-450 MPa. Therefore, the hemagglutination activity tends to be affected by the protein unit structure, while the stability of the glycone structure contributed to the remaining α-glucosidase inhibition activity. PMID:26416299

  16. A novel ribonuclease with potent HIV-1 reverse transcriptase inhibitory activity from cultured mushroom Schizophyllum commune.

    PubMed

    Zhao, Yong-Chang; Zhang, Guo-Qing; Ng, Tzi-Bun; Wang, He-Xiang

    2011-10-01

    A 20-kDa ribonuclease (RNase) was purified from fresh fruiting bodies of cultured Schizophyllum commune mushrooms. The RNase was not adsorbed on Affi-gel blue gel but adsorbed on DEAE-cellulose and CM-cellulose. It exhibited maximal RNase activity at pH 6.0 and 70°C. It demonstrated the highest ribonucleolytic activity toward poly (U) (379.5 μ/mg), the second highest activity toward poly (C) (244.7 μ/mg), less activity toward poly (A) (167.4 μ/mg), and much weaker activity toward poly (G) (114.5 μ/mg). The RNase inhibited HIV-1 reverse transcriptase with an IC(50) of 65 μM. No effect on [(3)H-methyl]-thymidine uptake by lymphoma MBL2 cells and leukemia L1210 cells was observed at 100 μM concentration of the RNase. A comparison of RNases from S. commune and Volvariella volvacea revealed that they demonstrated some similarities in N-terminal amino acid sequence, optimum pH and polyhomoribonucleotide specificity. However, some differences in chromatographic behavior and molecular mass were observed. PMID:22068498

  17. White kidney bean lectin exerts anti-proliferative and apoptotic effects on cancer cells.

    PubMed

    Chan, Yau Sang; Xia, Lixin; Ng, Tzi Bun

    2016-04-01

    A 60-kDa glucosamine binding lectin, white kidney bean lectin (WKBL), was purified from Phaseolus vulgaris cv. white kidney beans, by application of anion exchange chromatography on Q-Sepharose, affinity chromatography on Affi-gel blue gel, and FPLC-size exclusion on Superdex 75. The anti-proliferative activity of WKBL on HONE1 cells and HepG2 cells was stronger than the activity on MCF7 cells and WRL68 cells (IC50 values for a 48-h treatment with WKBL on HONE1 cells: 18.8 μM; HepG2 cells: 19.7 μM; MCF7 cells: 26.9 μM; and WRL68 cells: >80 μM). The activity could be reduced by addition of glucosamine, which occupies the binding sites of WKBL, indicating that carbohydrate binding is crucial for the activity. Annexin V-FITC and PI staining, JC-1 staining and Hoechst 33342 staining revealed that apoptosis was induced on WKBL-treated HONE1 cells and HepG2 cells, but not as obviously on MCF7 cells. Cell cycle analysis also showed a slight cell cycle arrest on HONE1 cells after WKBL treatment. Western blotting suggested that WKBL induced apoptosis of HONE1 cells occurred through the extrinsic apoptosis pathway, with detection of increased level of active caspase 3, 8 and 9. PMID:26769089

  18. Purification of the putative coxsackievirus B receptor from HeLa cells.

    PubMed

    Carson, S D; Chapman, N N; Tracy, S M

    1997-04-17

    We have identified a protein expressed by human and murine cells susceptible to coxsackievirus B3 (CVB3) infection and purified it from HeLa cells. This protein of approximately 45,000 Mr is expressed by HeLa cells and mouse fetal heart fibroblasts (susceptible to infection), and not by C3H murine fibroblasts or the human RD cell line (resistant). The protein was isolated from Triton X-100- deoxycholate lysates of HeLa cells by chromatography on concanavalin A-Sepharose, Affi-gel Blue, Phenyl Sepharose, and PBE94. The CVB3-binding fraction from PBE94 was blotted from SDS-polyacrylamide gel onto PVDF membrane for amino acid sequencing. Approximately 2 pmoles of CVB3-binding protein provided assignments for 26 consecutive residues: LSITTPEEMIEKAKGETAYLPXKFTL. This sequence corresponds neither to decay accelerating factor nor to nucleolin, both of which have previously been identified as CVB3-binding proteins, but does match two entries in GenBank. These data show that we have purified a novel CVB3-binding protein, the characteristics of which suggest the CVB group receptor has been purified. Identification of 26 amino acid residues in the protein and corresponding GenBank enteries will accelerate study of CVB tropism and the diseases caused by these viruses. PMID:9144533

  19. Blue-green algae

    MedlinePlus

    ... Talk with your health provider.Medications that slow blood clotting (Anticoagulant / Antiplatelet drugs)Blue-green algae might slow blood clotting. Taking blue-green algae along with medications that ...

  20. Greening the Blue Bottle.

    ERIC Educational Resources Information Center

    Wellman, Whitney E.; Noble, Mark E.

    2003-01-01

    Compares the revised Blue Bottle formulation to the classical Blue Bottle. Indicates that the revised formulation gives a somewhat bluer solution, but initially slower reduction when compared to the classical formulation. (Author/KHR)

  1. The Blue Water

    ERIC Educational Resources Information Center

    Berger, J. Joel

    1973-01-01

    Describes some of the advantages of an elementary science activity in which students discover that blowing through a straw into a bromthymol blue solution changes the color to yellow. Directions are provided for preparing the bromthymol blue solution. (JR)

  2. Blue nightshade poisoning

    MedlinePlus

    ... when someone eats parts of the blue nightshade plant. This article is for information only. DO NOT ... is found in the blue nightshade ( Solanum dulcamara ) plant, especially in the fruit and leaves.

  3. Gospel and Blues Improvisation.

    ERIC Educational Resources Information Center

    Smallwood, Richard

    1980-01-01

    The similarities and differences between blues and gospel music are identified and the author suggests that both blues and gospel music have inherent improvisational qualities. Methods of capitalizing on these qualities are presented. Selected readings and recordings are included. (KC)

  4. Blue nightshade poisoning

    MedlinePlus

    Blue nightshade poisoning occurs when someone eats parts of the blue nightshade plant. This article is for information only. DO NOT use it to treat or manage an actual poison exposure. If you or someone you ...

  5. Templated blue phases.

    PubMed

    Ravnik, Miha; Fukuda, Jun-ichi

    2015-11-21

    Cholesteric blue phases of a chiral liquid crystal are interesting examples of self-organised three-dimensional nanostructures formed by soft matter. Recently it was demonstrated that a polymer matrix introduced by photopolymerization inside a bulk blue phase not only stabilises the host blue phase significantly, but also serves as a template for blue phase ordering. We show with numerical modelling that the transfer of the orientational order of the blue phase to the surfaces of the polymer matrix, together with the resulting surface anchoring, can account for the templating behaviour of the polymer matrix inducing the blue phase ordering of an achiral nematic liquid crystal. Furthermore, tailoring the anchoring conditions of the polymer matrix surfaces can bring about orientational ordering different from those of bulk blue phases, including an intertwined complex of the polymer matrix and topological line defects of orientational order. Optical Kerr response of templated blue phases is explored, finding large Kerr constants in the range of K = 2-10 × 10(-9) m V(-2) and notable dependence on the surface anchoring strength. More generally, the presented numerical approach is aimed to clarify the role and actions of templating polymer matrices in complex chiral nematic fluids, and further to help design novel template-based materials from chiral liquid crystals. PMID:26412643

  6. Blue Willow Story Plates

    ERIC Educational Resources Information Center

    Fontes, Kris

    2009-01-01

    In the December 1997 issue of "SchoolArts" is a lesson titled "Blue Willow Story Plates" by Susan Striker. In this article, the author shares how she used this lesson with her middle-school students many times over the years. Here, she describes a Blue Willow plate painting project that her students made.

  7. Introducing the Blues.

    ERIC Educational Resources Information Center

    Sinclair, Bryan

    2000-01-01

    Discusses the history of the blues and presents a list of resources that are designed to introduce the blues, both as a feeling and as an influential part of American music and culture. Includes picture books and nonfiction for young readers, nonfiction for older readers, Web sites, and compact disks. (LRW)

  8. Detection of glutathione transferase activity on polyacrylamide gels.

    PubMed

    Ricci, G; Lo Bello, M; Caccuri, A M; Galiazzo, F; Federici, G

    1984-12-01

    A simple and sensitive assay for glutathione transferase activity on polyacrylamide gel is described. The method is based on the fast reduction of nitroblue tetrazolium salt by glutathione. Blue insoluble formazan colors the gel except in the glutathione transferase area. The stable and defined colorless zone is still detectable with 0.005 unit enzyme. This technique has been successfully applied with enzyme preparations of human heart and other tissues. PMID:6532239

  9. Fundamentals of gel dosimeters

    NASA Astrophysics Data System (ADS)

    McAuley, K. B.; Nasr, A. T.

    2013-06-01

    Fundamental chemical and physical phenomena that occur in Fricke gel dosimeters, polymer gel dosimeters, micelle gel dosimeters and genipin gel dosimeters are discussed. Fricke gel dosimeters are effective even though their radiation sensitivity depends on oxygen concentration. Oxygen contamination can cause severe problems in polymer gel dosimeters, even when THPC is used. Oxygen leakage must be prevented between manufacturing and irradiation of polymer gels, and internal calibration methods should be used so that contamination problems can be detected. Micelle gel dosimeters are promising due to their favourable diffusion properties. The introduction of micelles to gel dosimetry may open up new areas of dosimetry research wherein a range of water-insoluble radiochromic materials can be explored as reporter molecules.

  10. Blue ocean strategy.

    PubMed

    Kim, W Chan; Mauborgne, Renée

    2004-10-01

    Despite a long-term decline in the circus industry, Cirque du Soleil profitably increased revenue 22-fold over the last ten years by reinventing the circus. Rather than competing within the confines of the existing industry or trying to steal customers from rivals, Cirque developed uncontested market space that made the competition irrelevant. Cirque created what the authors call a blue ocean, a previously unknown market space. In blue oceans, demand is created rather than fought over. There is ample opportunity for growth that is both profitable and rapid. In red oceans--that is, in all the industries already existing--companies compete by grabbing for a greater share of limited demand. As the market space gets more crowded, prospects for profits and growth decline. Products turn into commodities, and increasing competition turns the water bloody. There are two ways to create blue oceans. One is to launch completely new industries, as eBay did with online auctions. But it's much more common for a blue ocean to be created from within a red ocean when a company expands the boundaries of an existing industry. In studying more than 150 blue ocean creations in over 30 industries, the authors observed that the traditional units of strategic analysis--company and industry--are of limited use in explaining how and why blue oceans are created. The most appropriate unit of analysis is the strategic move, the set of managerial actions and decisions involved in making a major market-creating business offering. Creating blue oceans builds brands. So powerful is blue ocean strategy, in fact, that a blue ocean strategic move can create brand equity that lasts for decades. PMID:15559577

  11. Fluorescent thin gel films using organic dyes and pigments

    NASA Astrophysics Data System (ADS)

    Nakazumi, Hiroyuki; Takashi, Tarao; Taniguchi, Shin-ichi; Nanto, Hidehito

    1997-10-01

    New organic-inorganic fluorescent thin gel films included with laser dyes or fluorescent organic pigments have been prepared for display application. The florescent dyes (benzoxazolium, pyrromethene, and rhodamine dyes) and super-fine particles of fluorescent pigments (coumarin and perylene) were successfully incorporated into thin silicate gel films prepared from tetraethoxysilane (TEOS), methyltriethoxysilane (MTES), and methoxysilane oligomer (MTSO) under acid catalyzed hydrolysis. The blue, green, and red luminescence were observed from these thin films (thickness: 100 - 400 nm), respectively. Fluorescence spectra, fluorescent quantum yield and lifetime of thin gel films are examined. Fluorescent peaks for most of dyes and pigments used in gel films were similar to those in solution, and fluorescent lifetime for dyes and pigments used in gel films were 2.9 - 4.5 ns. Photostability of fluorescent gel films is dependent on fluorescent organic dyes and pigments used and/or silicate gel matrixes. Coumarin and perylene pigments have higher fluorescent quantum yield in gel film prepared from MTSO. The large Stokes shift was observed in fluorescent gel film using coumarin and benzoxazolium dyes. The coumarin and perylene pigments are significantly photo- stable in gel film prepared from MTSO, and photodegradation of perylene red after irradiation of 500 W Xi-lamp for 30 min is below 20%.

  12. Testosterone Nasal Gel

    MedlinePlus

    Testosterone nasal gel is used to treat symptoms of low testosterone in men who have hypogonadism (a condition in which the body does not produce enough natural testosterone). Testosterone nasal gel is used only for men ...

  13. Mongolian blue spots

    MedlinePlus

    ... bruises. This can raise a question about possible child abuse. It is important to recognize that Mongolian blue ... Elsevier Saunders; 2011:chap 11. Read More Benign Child abuse - physical Rashes Update Date 4/14/2015 Updated ...

  14. Blue Ribbon Panel Report

    Cancer.gov

    An NCI Cancer Currents blog by the NCI acting director thanking the cancer community for contributing to the Cancer Moonshot Blue Ribbon Panel report, which was presented to the National Cancer Advisory Board on September 7.

  15. Methylene blue unresponsive methemoglobinemia

    PubMed Central

    Patnaik, Sibabratta; Natarajan, Manivachagan Muthappa; James, Ebor Jacob; Ebenezer, Kala

    2014-01-01

    Acquired methemoglobinemia is an uncommon blood disorder induced by exposure to certain oxidizing agents and drugs. Although parents may not give any history of toxin ingestion; with the aid of pulse-oximetry and blood gas analysis, we can diagnose methemoglobinemia. Prompt recognition of this condition is required in emergency situations to institute early methylene blue therapy. We report an unusual case of severe toxic methemoglobinemia, which did not respond to methylene blue, but was successfully managed with exchange transfusion. PMID:24872659

  16. Rat angiotensinogen and des(angiotensin I)angiotensinogen: purification, characterization, and partial sequencing.

    PubMed

    Bouhnik, J; Clauser, E; Strosberg, D; Frenoy, J P; Menard, J; Corvol, P

    1981-11-24

    Rat angiotensinogen was completely purified by a six-step procedure including (1) ammonium sulfate precipitation, (2) affinity chromatography on Affi-gel blue, (3) chromatography on DEAE-Sephacel, (4) chromatography on hydroxylapatite, (5) chromatography on Ultrogel AcA 54, and (6) isoelectric focusing. Two peaks of pure angiotensinogen were obtained, distinguishable by their isoelectric points (4.55 and 4.75). Both contained 23 microgram of angiotensin I/mg of protein. Sodium dodecyl sulfate--polyacrylamide gel electrophoresis of the peak with pI = 4.55 revealed two protein bands (respectively Mr 57000 and 59000) and a single protein band (Mr 57000) for the peak with pI = 4.75. The molecular weight of the latter homogeneous form, as determined by sedimentation equilibrium, was 55000. Only one immunoprecipitin line was observed when antiserum reacted with the heterogeneous angiotensinogen in Ouchterlony gels. The first 17 amino acids of the N-terminal region of the angiotensinogen with pI = 4.75 are reported. The amino acids in positions 10 and 11 which correspond to the renin cleavage site are leucyl-leucyl. The des(angiotensin I)angiotensinogen obtained after hydrolysis of angiotensinogen with pure mouse submaxillary gland renin was found to consist of a single protein band with an Mr of 56000 as revealed by sodium dodecyl sulfate--polyacrylamide gel electrophoresis. Only one N-terminal residue (leucyl) was obtained for this des(angiotensin I)angiotensinogen. These findings establish that renin only cleaves angiotensinogen at a single site. PMID:6797467

  17. Allergic contact dermatitis to acrylates in disposable blue diathermy pads.

    PubMed Central

    Sidhu, S. K.; Shaw, S.

    1999-01-01

    We report 2 cases of elicitation of allergic contact dermatitis to acrylates from disposable blue diathermy pads used on patients who underwent routine surgery. Their reactions were severe, and took approximately 5 weeks to resolve. Both patients gave a prior history of finger tip dermatitis following the use of artificial sculptured acrylic nails, which is a common, but poorly reported, cause of acrylate allergy. Patch testing subsequently confirmed allergies to multiple acrylates present in both the conducting gel of disposable blue diathermy pads, and artificial sculptured acrylic nails. We advocate careful history taking prior to surgery to avoid unnecessary exposure to acrylates in patients already sensitized. Images Figure 1 Figure 2 PMID:10364952

  18. Sol-Gel Glasses

    NASA Technical Reports Server (NTRS)

    Mukherjee, S. P.

    1985-01-01

    Multicomponent homogeneous, ultrapure noncrystalline gels/gel derived glasses are promising batch materials for the containerless glass melting experiments in microgravity. Hence, ultrapure, homogeneous gel precursors could be used to: (1) investigate the effect of the container induced nucleation on the glass forming ability of marginally glass forming compositions; and (2) investigate the influence of gravity on the phase separation and coarsening behavior of gel derived glasses in the liquid-liquid immiscibility zone of the nonsilicate systems having a high density phase. The structure and crystallization behavior of gels in the SiO2-GeO2 as a function of gel chemistry and thermal treatment were investigated. As are the chemical principles involved in the distribution of a second network former in silica gel matrix being investigated. The procedures for synthesizing noncrystalline gels/gel-monoliths in the SiO2-GeO2, GeO2-PbO systems were developed. Preliminary investigations on the levitation and thermal treatment of germania silicate gel-monoliths in the Pressure Facility Acoustic Levitator were done.

  19. A neutral branched platinum-acetylide complex possessing a tetraphenylethylene core: preparation of a luminescent organometallic gelator and its unexpected spectroscopic behaviour during sol-to-gel transition.

    PubMed

    Ren, Yuan-Yuan; Wu, Nai-Wei; Huang, Junhai; Xu, Zheng; Sun, Dan-Dan; Wang, Cui-Hong; Xu, Lin

    2015-10-21

    A neutral branched platinum-acetylide complex TPA possessing a tetraphenylethylene core was successfully prepared, which was found to form luminescent organometallic gels in ethyl acetate. Stimulated by temperature or F(-), the reversible gel-sol transition was realized. More interestingly, TPA exhibited an unexpected blue shift of the emission during the sol-to-gel transition. PMID:26323961

  20. CONFORMANCE IMPROVEMENT USING GELS

    SciTech Connect

    Randall S. Seright

    2003-09-01

    This report describes work performed during the second year of the project, ''Conformance Improvement Using Gels.'' The project has two objectives. The first objective is to identify gel compositions and conditions that substantially reduce flow through fractures that allow direct channeling between wells, while leaving secondary fractures open so that high fluid injection and production rates can be maintained. The second objective is to optimize treatments in fractured production wells, where the gel must reduce permeability to water much more than that to oil. Pore-level images from X-ray computed microtomography were re-examined for Berea sandstone and porous polyethylene. This analysis suggests that oil penetration through gel-filled pores occurs by a gel-dehydration mechanism, rather than a gel-ripping mechanism. This finding helps to explain why aqueous gels can reduce permeability to water more than to oil. We analyzed a Cr(III)-acetate-HPAM gel treatment in a production well in the Arbuckle formation. The availability of accurate pressure data before, during, and after the treatment was critical for the analysis. After the gel treatment, water productivity was fairly constant at about 20% of the pre-treatment value. However, oil productivity was stimulated by a factor of 18 immediately after the treatment. During the six months after the treatment, oil productivity gradually decreased to approach the pre-treatment value. To explain this behavior, we proposed that the fracture area open to oil flow was increased substantially by the gel treatment, followed by a gradual closing of the fractures during subsequent production. For a conventional Cr(III)-acetate-HPAM gel, the delay between gelant preparation and injection into a fracture impacts the placement, leakoff, and permeability reduction behavior. Formulations placed as partially formed gels showed relatively low pressure gradients during placement, and yet substantially reduced the flow capacity of

  1. Blue honeysuckle list 47

    Technology Transfer Automated Retrieval System (TEKTRAN)

    This manuscript summarizes descriptions for two newly released Lonicera caerulea L., blue honeysuckle, cultivars released for northern production. This fruit is popular in Russia and in Japan, particularly Hokkaido. It has possibility as a new fruit cultivar for North America. The University of Sask...

  2. CONFORMANCE IMPROVEMENT USING GELS

    SciTech Connect

    Randall S. Seright

    2004-09-30

    This report describes work performed during the third and final year of the project, ''Conformance Improvement Using Gels.'' Corefloods revealed throughput dependencies of permeability reduction by polymers and gels that were much more prolonged during oil flow than water flow. This behavior was explained using simple mobility ratio arguments. A model was developed that quantitatively fits the results and predicts ''clean up'' times for oil productivity when production wells are returned to service after application of a polymer or gel treatment. X-ray computed microtomography studies of gels in strongly water-wet Berea sandstone and strongly oil-wet porous polyethylene suggested that oil penetration through gel-filled pores occurs by a gel-dehydration mechanism, rather than gel-ripping or gel-displacement mechanisms. In contrast, analysis of data from the University of Kansas suggests that the gel-ripping or displacement mechanisms are more important in more permeable, strongly water-wet sandpacks. These findings help to explain why aqueous gels can reduce permeability to water more than to oil under different conditions. Since cement is the most commonly used material for water shutoff, we considered when gels are preferred over cements. Our analysis and experimental results indicated that cement cannot be expected to completely fill (top to bottom) a vertical fracture of any width, except near the wellbore. For vertical fractures with apertures less than 4 mm, the cement slurry will simply not penetrate very far into the fracture. For vertical fractures with apertures greater than 4 mm, the slurry may penetrate a substantial distance into the bottom part of the fracture. However, except near the wellbore, the upper part of the fracture will remain open due to gravity segregation. We compared various approaches to plugging fractures using gels, including (1) varying polymer content, (2) varying placement (extrusion) rate, (3) using partially formed gels, (4

  3. Cell viability in a wet silica gel.

    PubMed

    Nieto, Alejandra; Areva, Sami; Wilson, Timothy; Viitala, Reeta; Vallet-Regi, Maria

    2009-11-01

    A modified two-step sol-gel route using silicon ethoxide (TEOS) has been used to synthesize amorphous sol-gel-derived silica, which has been successfully used as a cell encapsulation matrix for 3T3 mouse fibroblasts and CRL-2595 epithelial cells due to its non-toxicity. The sol-gel procedure comprised a first, low pH hydrolysis step, followed by a neutral condensation-gelation step. A high water-to-TEOS ratio and the addition of d-glucose as a porogen and source of nutrients were chosen to minimize silica dissolution and improve the biocompatibility of the process. Indeed, the cell integrity in the encapsulation process was preserved by alcohol removal from the starting solution. Cells were then added in a buffered medium, causing rapid gelation and entrapment of the cells within a randomly structured siloxane matrix in the shape of a monolith, which was maintained in the wet state. MTT and alamarBlue assays were used to check the cytotoxicity of the silica gels and the viability of entrapped cells at initial times in contact with silica. To improve cell attachment, cell clumping experiments - where groups of cells were formed - were designed, rendering improved viability. The obtained materials are therefore excellent candidates for designing tissue-culture scaffolds and implantable bioreactors for biomedical applications. PMID:19481618

  4. Antifungal peptides, a heat shock protein-like peptide, and a serine-threonine kinase-like protein from Ceylon spinach seeds.

    PubMed

    Wang, Hexiang; Ng, Tzi Bun

    2004-07-01

    Two antifungal peptides (designated alpha- and beta-basrubrins) with molecular masses of 4-5 kDa and distinct N-terminal sequences, and a peptide and a protein with N-terminal sequences resembling heat shock protein (hsp) and serine-threonine kinase, respectively, were isolated from seeds of the Ceylon spinach Basella rubra. The purification procedure entailed saline extraction, (NH4)2SO4 precipitation, ion exchange chromatography on DEAE-cellulose, affinity chromatography on Affi-gel blue gel, ion exchange chromatography on CM-cellulose, and FPLC-gel filtration on a Superdex peptide column. alpha- and beta-basrubrins inhibited mycelial growth in Botrytis cirerea with an IC50 value of 7.5 and 14.7 microM, respectively, Mycosphaerella arachidicola with an IC50 of 12.4 and 6.9 microM, and Fusarium oxysporum with an IC50 of 5.8 and 6.2 microM. Neither alpha-basrubrin nor beta-basrubin exhibited DNase, RNase, lectin or protease activity, indicating that their antifungal action is not due to these activities. HIV-1 reverse transcriptase was inhibited by alpha- and beta-basrubrins with an IC50 of 246 and 370 microM, respectively. Translation in rabbit reticulocyte lysate was inhibited by alpha- and beta-basrubrins with an IC50 of 400 and 100 nM. The heat shock protein-like peptide and serine-threonine kinase-like protein exhibited a molecular mass of 3 and 30 kDa, respectively. They inhibited neither translation in a rabbit reticulocyte system at concentrations up to 50 microM nor HIV-1 reverse transcriptase activity at concentrations up to 400 microM. They did not exert antifungal activity toward B. cinerea, M. arachidicola, and F. oxysporum when tested up to 16 microg. None of the aforementioned proteins demonstrated DNase, RNase, protease or lectin activity. PMID:15245882

  5. Galactinol synthase from kidney bean cotyledon and zucchini leaf. Purification and N-terminal sequences.

    PubMed Central

    Liu, J J; Odegard, W; de Lumen, B O

    1995-01-01

    Galactinol synthase (GS) was purified 1591-fold with a 3.9% recovery from the cotyledon of kidney bean (Phaseolus vulgaris) by a novel scheme consisting of ammonium sulfate fractionation followed by diethylaminoethyl, Affi-Gel Blue, and UDP-hexanolamine affinity chromatography. The purified enzyme had a specific activity of 8.75 mumol mg-1 min-1, a pH optimum of 7.0, and requirements for manganese ion and DTT. The enzyme exhibited a Km = 0.4 mM for UDP-galactose and a Km = 4.5 mM for myo-inositol. It was identified as a 38-kD peptide that co-purified with a 41- and a 43-kD peptide as shown by sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE). Purification to homogeneity was achieved by isolating the 38-kD peptide from the SDS-PAGE gel. To clarify conflicting reports in the literature about the relative molecular mass of purified GS from zucchini leaf (Cucurbita pepo), a similar scheme with modified eluting conditions was used to purify GS from this source. Zucchini leaf GS was purified to homogeneity and identified as a 36-kD peptide on SDS-PAGE. Partial N-terminal sequences of the 38-kD peptide from kidney bean cotyledon and the 36-kD peptide from zucchini leaf were obtained. To facilitate identification of GS during the purification, an assay utilizing thin-layer chromatography and an isotopic analytic imaging scanner was developed. PMID:7480343

  6. Purification and properties of an oestrogen-stimulated mouse uterine glycoprotein (approx. 70 kDa).

    PubMed Central

    Teng, C T; Walker, M P; Bhattacharyya, S N; Klapper, D G; DiAugustine, R P; McLachlan, J A

    1986-01-01

    An oestrogen-induced secretory protein from mouse uterine luminal fluid was purified by CM-Affi-Gel Blue chromatography and reverse-phase h.p.l.c. This protein has an apparent molecular mass of approx. 70 kDa both by SDS/polyacrylamide-gel electrophoresis (with or without 2-mercaptoethanol) and by gel-filtration column chromatography, indicating that it exists as a single-chain polypeptide. Further analysis of the protein revealed that it is highly basic (pI greater than or equal to 10) and is a glycoprotein. The N-terminus appears to be blocked to Edman degradation. The partial amino acid sequence of a fragment was obtained by cleavage with CNBr; no sequence homology was apparent between the analysed fragment and other known sequences. The incorporation of [35S]methionine into uterine proteins in vitro revealed that oestrogen treatment of immature mice stimulates both synthesis and secretion of the 70 kDa protein. An enzyme-linked immunosorbent assay with polyclonal antibody was used to determine the tissue distribution of the protein. Tissues such as lung, brain, spleen, muscle, intestine, liver, kidney and ovary of oestrogen-treated mice did not have detectable amounts of the 70 kDa protein. Immunoreactivity was present in uterine and vaginal tissues from oestrogen-treated animals. The 70 kDa protein was not induced by testosterone or progesterone. Although the function of this protein is unknown, it is useful as a marker for the study of oestrogen action in the mammalian uterus as well as regulation of gene expression at the molecular level. Images Fig. 1. Fig. 2. Fig. 3. Fig. 4. Fig. 6. PMID:3814091

  7. CONFORMANCE IMPROVEMENT USING GELS

    SciTech Connect

    Randall S. Seright

    2004-03-01

    This technical progress report describes work performed from September 1, 2003, through February 29, 2004, for the project, ''Conformance Improvement Using Gels.'' We examined the properties of several ''partially formed'' gels that were formulated with a combination of high and low molecular weight HPAM polymers. After placement in 4-mm-wide fractures, these gels required about 25 psi/ft for brine to breach the gel (the best performance to date in fractures this wide). After this breach, stabilized residual resistance factors decreased significantly with increased flow rate. Also, residual resistance factors were up to 9 times greater for water than for oil. Nevertheless, permeability reduction factors were substantial for both water and oil flow. Gel with 2.5% chopped fiberglass effectively plugged 4-mm-wide fractures if a 0.5-mm-wide constriction was present. The ability to screen-out at a constriction appears crucial for particulate incorporation to be useful in plugging fractures. In addition to fiberglass, we examined incorporation of polypropylene fibers into gels. Once dispersed in brine or gelant, the polypropylene fibers exhibited the least gravity segregation of any particulate that we have tested to date. In fractures with widths of at least 2 mm, 24-hr-old gels (0.5% high molecular weight HPAM) with 0.5% fiber did not exhibit progressive plugging during placement and showed extrusion pressure gradients similar to those of gels without the fiber. The presence of the fiber roughly doubled the gel's resistance to first breach by brine flow. The breaching pressure gradients were not as large as for gels made with high and low molecular weight polymers (mentioned above). However, their material requirements and costs (i.e., polymer and/or particulate concentrations) were substantially lower than for those gels. A partially formed gel made with 0.5% HPAM did not enter a 0.052-mm-wide fracture when applying a pressure gradient of 65 psi/ft. This result

  8. Modeling chemoresponsive polymer gels.

    PubMed

    Kuksenok, Olga; Deb, Debabrata; Dayal, Pratyush; Balazs, Anna C

    2014-01-01

    Stimuli-responsive gels are vital components in the next generation of smart devices, which can sense and dynamically respond to changes in the local environment and thereby exhibit more autonomous functionality. We describe recently developed computational methods for simulating the properties of such stimuli-responsive gels in the presence of optical, chemical, and thermal gradients. Using these models, we determine how to harness light to drive shape changes and directed motion in spirobenzopyran-containing gels. Focusing on oscillating gels undergoing the Belousov-Zhabotinksy reaction, we demonstrate that these materials can spontaneously form self-rotating assemblies, or pinwheels. Finally, we model temperature-sensitive gels that encompass chemically reactive filaments to optimize the performance of this system as a homeostatic device for regulating temperature. These studies could facilitate the development of soft robots that autonomously interconvert chemical and mechanical energy and thus perform vital functions without the continuous need of external power sources. PMID:24498954

  9. The Blue Emu

    NASA Technical Reports Server (NTRS)

    Descalzi, Doug; Gillett, John; Gordon, Carlton; Keener, ED; Novak, Ken; Puente, Laura

    1993-01-01

    The primary goal in designing the Blue Emu was to provide an airline with a cost efficient and profitable means of transporting passengers between the major cities in Aeroworld. The design attacks the market where a demand for inexpensive transportation exists and for this reason the Blue Emu is an attractive investment for any airline. In order to provide a profitable aircraft, special attention was paid to cost and economics. For example, in manufacturing, simplicity was stressed in structural design to reduce construction time and cost. Aerodynamic design employed a tapered wing which reduced the induced drag coefficient while also reducing the weight of the wing. Even the propulsion system was selected with cost effectiveness in mind, yet also to maintain the marketability of the aircraft. Thus, in every aspect of the design, consideration was given to economics and marketability of the final product.

  10. Prostatic blue nevus.

    PubMed

    Anderco, Denisa; Lazăr, Elena; Tăban, Sorina; Miclea, Fl; Dema, Alis

    2010-01-01

    We report the case of a 69-year-old patient with no significant personal urological history. The clinical and ultrasound examination revealed a prostatic gland with increased volume and homogenous appearance. After transurethral resection, multiples gray-brown-blackish prostatic chips were obtained, which could be confused with a malignant melanoma. The histological routine examination in conjunction with the histochemical (Fontana-Masson) and immunohistochemical (S100, HMB45) reactions established the diagnosis of prostatic blue nevus. The presence of melanin in prostatic tissue is an unusual aspect, being encountered three distinct lesions: blue nevus, melanosis and malignant melanoma. Recognition and correct classification of each of these three entities is fundamental, concerning the clinical and prognosis implications. PMID:20809037

  11. Voyager 1 'Blue Movie'

    NASA Technical Reports Server (NTRS)

    2000-01-01

    This is the original Voyager 'Blue Movie' (so named because it was built from Blue filter images). It records the approach of Voyager 1 during a period of over 60 Jupiter days. Notice the difference in speed and direction of the various zones of the atmosphere. The interaction of the atmospheric clouds and storms shows how dynamic the Jovian atmosphere is.

    As Voyager 1 approached Jupiter in 1979, it took images of the planet at regular intervals. This sequence is made from 66 images taken once every Jupiter rotation period (about 10 hours). This time-lapse movie uses images taken every time Jupiter longitude 68W passed under the spacecraft. These images were acquired in the Blue filter from Jan. 6 to Feb. 3 1979. The spacecraft flew from 58 million kilometers to 31 million kilometers from Jupiter during that time.

    This time-lapse movie was produced at JPL by the Image Processing Laboratory in 1979.

  12. The characterisation of a genipin-gelatin gel dosimeter

    NASA Astrophysics Data System (ADS)

    Davies, J. B.; Bosi, S.; Baldock, C.

    2010-11-01

    Genipin cross links gelatin to slowly form a blue colour that bleaches upon irradiation. Spectrophotometric measurements of the absorbance change following irradiation to doses up to 100 Gy gives a linear dose response for certain concentrations of the gel ingredients; genipin, gelatin and sulphuric acid. Dose sensitivity increases with increasing concentrations of sulphuric acid and genipin and is also strongly dependent on the time allowed for the genipin-gelatin cross linking reaction (referred to here as blending) to take place. The optimum formulation of this gel was found for genipin concentration between 0.3 - 0.5 mM and blending time of at least 4 h.

  13. Western Blot of Stained Proteins from Dried Polyacrylamide Gels

    NASA Technical Reports Server (NTRS)

    Gruber, Claudia; Stan-Lotter, Helga

    1996-01-01

    Western blotting of proteins is customarily performed following their separation on polyacrylamide gels, either prior to staining (1) or, as recently reported, following staining (2). We describe here Western blotting with stained gels, which had been dried and some of which had been stored for years. This procedure permits immunological analysis of proteins, to which antisera may have become available only later, or where the application of newly developed sensitive detection methods is desired. Once rehydration of the gels is achieved, proteins can be-transferred to blotting membranes by any appropriate protocol. Proteins stained with Coomassie Blue have to be detected with a non-chromogenic method, such as the film-based enhanced chemiluminescence (ECL)2) procedure (3). Silver stained proteins, which transfer in the colorless form, may be visualized by any detection method, although, because of the usually very low amounts of proteins, detection by ECL is preferable. Blotting of stained proteins from rehydrated gels is as rapid and as quantitative as from freshly prepared gels, in contrast to blotting from wet stained gels, which requires extensive washing and results in low transfer efficiency (2). Together with a photographic record of the gel pattern, unambiguous identification of immunoreactive proteins from complex mixtures is possible. Some further applications of this work are discussed.

  14. Viscoelasticity of silica gels

    SciTech Connect

    Scherer, G.W.

    1995-12-01

    The response of silica gels to mechanical loads depends on the properties of the solid phase and the permeability of the network. Understanding this behavior is essential for modeling of stresses developed during drying or heating of gels. The permeability and the mechanical properties are readily determined from a simple beam-bending experiment, by measuring the load relaxation that occurs at constant deflection. Load decay results from movement of the liquid within the network; in addition, there may be viscoelastic relaxation of the network itself. Silica gel is viscoelastic in chemically aggressive media, but in inert liquids (such as ethanol or acetone) it is elastic. Experiments show that the viscoelastic relaxation time decreases as the concentration and pH of the water in the pore liquid increase. During drying, the permeability decreases and the viscosity increases, both exhibiting a power-law dependence on density of the gel network.

  15. Testosterone Nasal Gel

    MedlinePlus

    ... enough natural testosterone). Testosterone nasal gel is used only for men with low testosterone levels caused by ... is a controlled substance. Prescriptions may be refilled only a limited number of times; ask your pharmacist ...

  16. Microfluidics with Gel Emulsions

    NASA Astrophysics Data System (ADS)

    Priest, Craig; Surenjav, Enkhtuul; Herminghaus, Stephan; Seemann, Ralf

    2006-03-01

    Microfluidic processing is usually achieved using single phase liquids. Instead, we use monodisperse emulsions to compartment liquids within microchannel geometries. At low continuous phase volume fractions, droplets self-organize to form well-defined arrangements, analogous to foam. While it is well-known that confined geometries can induce rearrangement of foam compartments at the millimeter-scale, similar dynamics are also expected for gel emulsions. We have studied online generation, organization and manipulation of gel emulsions using a variety of microchannel geometries. ``Passive'' reorganization, based on fixed channel geometries, can be supplemented by ``active'' manipulation by incorporating a ferrofluid phase. A ferromagnetic phase facilitates reorganization of liquid compartments on demand using an electromagnetic trigger. Moreover, coalescence between adjacent compartments within a gel emulsion can be induced using electrical potential. Microfluidics using gel emulsions will be well-suited for combinatorial chemistry, DNA sequencing, drug screening and protein crystallizations.

  17. Preparation of chitosan gel

    NASA Astrophysics Data System (ADS)

    Moussaoui, Y.; Mnasri, N.; Elaloui, E.; Ben Salem, R.; Lagerge, S.; de Menorval, L. C.

    2012-06-01

    Aerogel conditioning of the chitosan makes it possible to prepare porous solids of significant specific surface. The increase in the chitosan concentration or the degree of acetylation decreases the specific surface of the synthesized chitosan gel. Whereas drying with supercritical CO2 more effectively makes it possible to preserve the volume of the spheres of gel and to have a more significant specific surface in comparison with evaporative drying.

  18. Crystallization from Gels

    NASA Astrophysics Data System (ADS)

    Narayana Kalkura, S.; Natarajan, Subramanian

    Among the various crystallization techniques, crystallization in gels has found wide applications in the fields of biomineralization and macromolecular crystallization in addition to crystallizing materials having nonlinear optical, ferroelectric, ferromagnetic, and other properties. Furthermore, by using this method it is possible to grow single crystals with very high perfection that are difficult to grow by other techniques. The gel method of crystallization provides an ideal technique to study crystal deposition diseases, which could lead to better understanding of their etiology. This chapter focuses on crystallization in gels of compounds that are responsible for crystal deposition diseases. The introduction is followed by a description of the various gels used, the mechanism of gelling, and the fascinating phenomenon of Liesegang ring formation, along with various gel growth techniques. The importance and scope of study on crystal deposition diseases and the need for crystal growth experiments using gel media are stressed. The various crystal deposition diseases, viz. (1) urolithiasis, (2) gout or arthritis, (3) cholelithiasis and atherosclerosis, and (4) pancreatitis and details regarding the constituents of the crystal deposits responsible for the pathological mineralization are discussed. Brief accounts of the theories of the formation of urinary stones and gallstones and the role of trace elements in urinary stone formation are also given. The crystallization in gels of (1) the urinary stone constituents, viz. calcium oxalate, calcium phosphates, uric acid, cystine, etc., (2) the constituents of the gallstones, viz. cholesterol, calcium carbonate, etc., (3) the major constituent of the pancreatic calculi, viz., calcium carbonate, and (4) cholic acid, a steroidal hormone are presented. The effect of various organic and inorganic ions, trace elements, and extracts from cereals, herbs, and fruits on the crystallization of major urinary stone and gallstone

  19. Conformance Improvement Using Gels

    SciTech Connect

    Seright, Randall S.; Schrader, Richard; II Hagstrom, John; Wang, Ying; Al-Dahfeeri, Abdullah; Gary, Raven; Marin; Amaury; Lindquist, Brent

    2002-09-26

    This research project had two objectives. The first objective was to identify gel compositions and conditions that substantially reduce flow through fractures that allow direct channeling between wells, while leaving secondary fractures open so that high fluid injection and production rates can be maintained. The second objective was to optimize treatments in fractured production wells, where the gel must reduce permeability to water much more than that to oil.

  20. The Blue Marble

    NASA Technical Reports Server (NTRS)

    2002-01-01

    This spectacular Moderate Resolution Imaging Spectroradiometer (MODIS) 'blue marble' image is based on the most detailed collection of true-color imagery of the entire Earth to date. Using a collection of satellite-based observations, scientists and visualizers stitched together months of observations of the land surface, oceans, sea ice, and clouds into a seamless, true-color mosaic of every square kilometer (.386 square mile) of our planet. Most of the information contained in this image came from MODIS, illustrating MODIS' outstanding capacity to act as an integrated tool for observing a variety of terrestrial, oceanic, and atmospheric features of the Earth. The land and coastal ocean portions of this image is based on surface observations collected from June through September 2001 and combined, or composited, every eight days to compensate for clouds that might block the satellite's view on any single day. Global ocean color (or chlorophyll) data was used to simulate the ocean surface. MODIS doesn't measure 3-D features of the Earth, so the surface observations were draped over topographic data provided by the U.S. Geological Survey EROS Data Center. MODIS observations of polar sea ice were combined with observations of Antarctica made by the National Oceanic and Atmospheric Administration's AVHRR sensor-the Advanced Very High Resolution Radiometer. The cloud image is a composite of two days of MODIS imagery collected in visible light wavelengths and a third day of thermal infra-red imagery over the poles. A large collection of imagery based on the blue marble in a variety of sizes and formats, including animations and the full (1 km) resolution imagery, is available at the Blue Marble page. Image by Reto Stockli, Render by Robert Simmon. Based on data from the MODIS Science Team

  1. Polyacrylamide gel electrophoresis.

    PubMed

    Chrambach, A; Rodbard, D

    1971-04-30

    Polyacrylamide gel electrophoresis (PAGE) provides a versatile, gentle, high resolution method for fractionation and physical-chemical characterization of molecules on the basis of size, conformation, and net charge. The polymerization reaction can be rigorously controlled to provide uniform gels of reproducible, measurable pore size over a wide range. This makes it possible to obtain reproducible relative mobility (Rf) values as physical-chemical constants. Application and extension of Ogston's (random fiber) model for a gel allows for calculation of molecular volume, surface area, or radius, free mobility, and valence from RJ measurements at several gel concentrations, to calculate gel concentration for optimal resolution, and to predict behavior of macromolecules on gel gradients by computerized methods. Extension of classical moving boundary theory has been used to generate multiphasic buffer systems (providing selective stacking, unstacking, restacking, and preparative steady-state-stacking) with known operating characteristics for any pH at 0 degrees and 25 degrees C. A general strategy for isolation of macromolecules and for macromolecular mapping has been developed. Preparative scale PAGE is operational for milligram loads and feasible for gram quantities. PMID:4927678

  2. Purification and partial structural and kinetic characterization of an aromatic L-alpha-hydroxy acid dehydrogenase from epimastigotes of Trypanosoma cruzi.

    PubMed

    Montemartini, M; Santomé, J A; Cazzulo, J J; Nowicki, C

    1994-11-01

    An aromatic L-alpha-hydroxyacid dehydrogenase (AHADH) was purified to homogeneity from epimastigotes of Trypanosoma cruzi by a method involving chromatography on DEAE-cellulose, hydrophobic interaction chromatography on Phenyl-Sepharose and affinity chromatography on Affi-Gel Blue. The purified enzyme showed a single band in SDS-PAGE, with an apparent molecular mass of 36 kDa. Since the apparent molecular mass of the native enzyme, determined by gel filtration, is about 80 kDa, the native enzyme is a dimer of similar subunits. The amino acid composition was determined, as well as the sequences of 4 internal peptides obtained by CNBr cleavage at Met residues, and one peptide obtained after tryptic digestion. Three of the peptides presented considerable sequence similarity with the corresponding sequences of several malate dehydrogenases. The optimal pH for the enzyme reaction with p-hydroxyphenyl pyruvate and NADH as substrates was 7.5; that for the reverse reaction was 9.5. The apparent Km values for phenylpyruvate and p-hydroxyphenyl-pyruvate were 48 and 117 microM, respectively; that for L-phenyllactate in the reverse reaction was 420 microM. The enzyme was much less active with alpha-isocaproic acid as substrate, and other acids, including pyruvic and oxaloacetic, were not substrates at all. L-phenyllactic acid, but not the D-isomer, acted as substrate. The enzyme can therefore be considered as a general aromatic L-alpha-hydroxyacid dehydrogenase. The low apparent Km value for NADH (25 microM in the presence of phenylpyruvate) makes AHADH a candidate for the reoxidation of cytosolic NADH in T. cruzi. PMID:7891739

  3. Tunable Optical Properties of Metal Nanoparticle Sol-Gel Composites

    NASA Technical Reports Server (NTRS)

    Smith, David D.; Snow, Lanee A.; Sibille, Laurent; Ignont, Erica

    2001-01-01

    We demonstrate that the linear and non-linear optical properties of sol-gels containing metal nanoparticles are highly tunable with porosity. Moreover, we extend the technique of immersion spectroscopy to inhomogeneous hosts, such as aerogels, and determine rigorous bounds for the average fractional composition of each component, i.e., the porosity of the aerogel, or equivalently, for these materials, the catalytic dispersion. Sol-gels containing noble metal nanoparticles were fabricated and a significant blue-shift in the surface plasmon resonance (SPR) was observed upon formation of an aerogel, as a result of the decrease in the dielectric constant of the matrix upon supercritical extraction of the solvent. However, as a result of chemical interface damping and aggregation this blue-shift does not strictly obey standard effective medium theories. Mitigation of these complications is achieved by avoiding the use of alcohol and by annealing the samples in a reducing atmosphere.

  4. Blue ocean leadership.

    PubMed

    Kim, W Chan; Mauborgne, Renée

    2014-05-01

    Ten years ago, two INSEAD professors broke ground by introducing "blue ocean strategy," a new model for discovering uncontested markets that are ripe for growth. In this article, they apply their concepts and tools to what is perhaps the greatest challenge of leadership: closing the gulf between the potential and the realized talent and energy of employees. Research indicates that this gulf is vast: According to Gallup, 70% of workers are disengaged from their jobs. If companies could find a way to convert them into engaged employees, the results could be transformative. The trouble is, managers lack a clear understanding of what changes they could make to bring out the best in everyone. Here, Kim and Mauborgne offer a solution to that problem: a systematic approach to uncovering, at each level of the organization, which leadership acts and activities will inspire employees to give their all, and a process for getting managers throughout the company to start doing them. Blue ocean leadership works because the managers' "customers"-that is, the people managers oversee and report to-are involved in identifying what's effective and what isn't. Moreover, the approach doesn't require leaders to alter who they are, just to undertake a different set of tasks. And that kind of change is much easier to implement and track than changes to values and mind-sets. PMID:24956870

  5. Blue emitting undecaplatinum clusters

    NASA Astrophysics Data System (ADS)

    Chakraborty, Indranath; Bhuin, Radha Gobinda; Bhat, Shridevi; Pradeep, T.

    2014-07-01

    A blue luminescent 11-atom platinum cluster showing step-like optical features and the absence of plasmon absorption was synthesized. The cluster was purified using high performance liquid chromatography (HPLC). Electrospray ionization (ESI) and matrix assisted laser desorption ionization (MALDI) mass spectrometry (MS) suggest a composition, Pt11(BBS)8, which was confirmed by a range of other experimental tools. The cluster is highly stable and compatible with many organic solvents.A blue luminescent 11-atom platinum cluster showing step-like optical features and the absence of plasmon absorption was synthesized. The cluster was purified using high performance liquid chromatography (HPLC). Electrospray ionization (ESI) and matrix assisted laser desorption ionization (MALDI) mass spectrometry (MS) suggest a composition, Pt11(BBS)8, which was confirmed by a range of other experimental tools. The cluster is highly stable and compatible with many organic solvents. Electronic supplementary information (ESI) available: Details of experimental procedures, instrumentation, chromatogram of the crude cluster; SEM/EDAX, DLS, PXRD, TEM, FT-IR, and XPS of the isolated Pt11 cluster; UV/Vis, MALDI MS and SEM/EDAX of isolated 2 and 3; and 195Pt NMR of the K2PtCl6 standard. See DOI: 10.1039/c4nr02778g

  6. CONFORMANCE IMPROVEMENT USING GELS

    SciTech Connect

    Randall S. Seright

    2002-02-28

    This technical progress report describes work performed from June 20 through December 19, 2001, for the project, ''Conformance Improvement Using Gels''. Interest has increased in some new polymeric products that purport to substantially reduce permeability to water while causing minimum permeability reduction to oil. In view of this interest, we are currently studying BJ's Aqua Con. Results from six corefloods revealed that the Aqua Con gelant consistently reduced permeability to water more than that to oil. However, the magnitude of the disproportionate permeability reduction varied significantly for the various experiments. Thus, as with most materials tested to date, the issue of reproducibility and control of the disproportionate permeability remains to be resolved. Concern exists about the ability of gels to resist washout after placement in fractures. We examined whether a width constriction in the middle of a fracture would cause different gel washout behavior upstream versus downstream of the constriction. Tests were performed using a formed Cr(III)-acetate-HPAM gel in a 48-in.-long fracture with three sections of equal length, but with widths of 0.08-, 0.02-, and 0.08-in., respectively. The pressure gradients during gel extrusion (i.e., placement) were similar in the two 0.08-in.-wide fracture sections, even though they were separated by a 0.02-in.-wide fracture section. The constriction associated with the middle fracture section may have inhibited gel washout during the first pulse of brine injection after gel placement. However, during subsequent phases of brine injection, the constriction did not inhibit washout in the upstream fracture section any more than in the downstream section.

  7. Pluto’s Blue Haze

    NASA Video Gallery

    The sky on Pluto is blue! Kind of. This is Pluto in an Minute. So it’s not exactly the case that the sky on Pluto is blue, rather, what the New Horizons science team has found in recent images do...

  8. Swelling of Olympic Gels

    NASA Astrophysics Data System (ADS)

    Lang, M.; Fischer, J.; Werner, M.; Sommer, J.-U.

    2014-06-01

    The swelling equilibrium of Olympic gels, which are composed of entangled cyclic polymers, is studied by Monte Carlo simulations. In contrast to chemically cross-linked polymer networks, we observe that Olympic gels made of chains with a larger degree of polymerization, N, exhibit a smaller equilibrium swelling degree, Q∝N-0.28ϕ0-0.72, at the same polymer volume fraction ϕ0 at network preparation. This observation is explained by a desinterspersion (reorganization with release of nontrapped entanglements) process of overlapping nonconcatenated rings upon swelling.

  9. Carbon dioxide assimilation in blue-green algae: initial studies on the structure of ribulose 1,5-bisphosphate carboxylase.

    PubMed Central

    Tabita, F R; Stevens, S E; Gibson, J L

    1976-01-01

    D-Ribulose 1,5-bisphosphate carboxylase was purified from the blue-green alga Anabaena cylindrica (Lemm) by procedures involving acid precipitation, ammonium sulfate fractionation, and Sephadex G-200 gel filtration. The enzyme was homogeneous by the criterion of polyacrylamide disc gel electrophoresis and was a multimer of a single-size polypeptide chain of 54,000 daltons. The carboxylases from four species of blue-green algae (Anabaena, Nostoc strain MAC, Agmenellum quadruplicatum strain PR-6, and Anacystis nidulans strain TX20) were closely similar in molecular size, since enzyme activity was eluted at the same volume after sucrose gradient centrifugation. Further analysis by gel filtration indicated that the four blue-green algal carboxylases were nearly identical in molecular weight, ranging from 449 to 453,000. The amino acid composition of the Anabaena carboxylase was determined and was found to resemble closely the composition of the large subunit from eukaryotic photosynthetic organisms. Images PMID:812868

  10. Rheology of Active Gels

    NASA Astrophysics Data System (ADS)

    Chen, Daniel

    2015-03-01

    Active networks drive a diverse range of critical processes ranging from motility to division in living cells, yet a full picture of their rheological capabilities in non-cellular contexts is still emerging, e.g., How does the rheological response of a network capable of remodeling under internally-generated stresses differ from that of a passive biopolymer network? In order to address this and other basic questions, we have engineered an active gel composed of microtubules, bidirectional kinesin motors, and molecular depletant that self-organizes into a highly dynamic network of active bundles. The network continually remodels itself under ATP-tunable cycles of extension, buckling, fracturing, and self-healing. Using confocal rheometry we have simultaneously characterized the network's linear and non-linear rheological responses to shear deformation along with its dynamic morphology. We find several surprising and unique material properties for these active gels; most notably, rheological cloaking, the ability of the active gel to drive large-scale fluid mixing over several orders of flow magnitude while maintaining an invariant, solid-like rheological profile and spontaneous flow under confinement, the ability to exert micro-Newton forces to drive persistent directed motion of the rheometer tool. Taken together, these results and others to be discussed highlight the rich stress-structure-dynamics relationships in this class of biologically-derived active gels.

  11. Blue ellipticals in compact groups

    NASA Technical Reports Server (NTRS)

    Zepf, Stephen E.; Whitmore, Bradley C.

    1990-01-01

    By studying galaxies in compact groups, the authors examine the hypothesis that mergers of spiral galaxies make elliptical galaxies. The authors combine dynamical models of the merger-rich compact group environment with stellar evolution models and predict that roughly 15 percent of compact group ellipticals should be 0.15 mag bluer in B - R color than normal ellipticals. The published colors of these galaxies suggest the existence of this predicted blue population, but a normal distribution with large random errors can not be ruled out based on these data alone. However, the authors have new ultraviolet blue visual data which confirm the blue color of the two ellipticals with blue B - R colors for which they have their own colors. This confirmation of a population of blue ellipticals indicates that interactions are occurring in compact groups, but a blue color in one index alone does not require that these ellipticals are recent products of the merger of two spirals. The authors demonstrate how optical spectroscopy in the blue may distinguish between a true spiral + spiral merger and the swallowing of a gas-rich system by an already formed elliptical. The authors also show that the sum of the luminosity of the galaxies in each group is consistent with the hypothesis that the final stage in the evolution of compact group is an elliptical galaxy.

  12. Blue moons and Martian sunsets.

    PubMed

    Ehlers, Kurt; Chakrabarty, Rajan; Moosmüller, Hans

    2014-03-20

    The familiar yellow or orange disks of the moon and sun, especially when they are low in the sky, and brilliant red sunsets are a result of the selective extinction (scattering plus absorption) of blue light by atmospheric gas molecules and small aerosols, a phenomenon explainable using the Rayleigh scattering approximation. On rare occasions, dust or smoke aerosols can cause the extinction of red light to exceed that for blue, resulting in the disks of the sun and moon to appear as blue. Unlike Earth, the atmosphere of Mars is dominated by micron-size dust aerosols, and the sky during sunset takes on a bluish glow. Here we investigate the role of dust aerosols in the blue Martian sunsets and the occasional blue moons and suns on Earth. We use the Mie theory and the Debye series to calculate the wavelength-dependent optical properties of dust aerosols most commonly found on Mars. Our findings show that while wavelength selective extinction can cause the sun's disk to appear blue, the color of the glow surrounding the sun as observed from Mars is due to the dominance of near-forward scattering of blue light by dust particles and cannot be explained by a simple, Rayleigh-like selective extinction explanation. PMID:24663457

  13. Blue upconversion thulium laser

    SciTech Connect

    Nguyen, D.C.; Faulkner, G.E.; Weber, M.E.; Dulick, M.

    1990-01-01

    Upconversion has been an active area of research for at least two decades, mainly because of its wide ranging applications from infrared quantum counters, visible-emitting phosphors, to upconversion lasers. The upconversion lasers have recently become attractive with the advent of semiconductor laser diodes as the pump source. In an upconversion laser, the laser active ion is excited by internal upconversion of near-ir or red light via multiphoton excitation or cooperative processes and emits anti-Stokes visible light. Since the laser diode output wavelength can be composition turned to match the upconversion laser ion absorption lines, a substantial fraction of the ions can be driven into higher energy levels, thus enhancing the upconversion process. These upconversion solid-state lasers offer a potentially simple and compact source of visible coherent light with semiconductor laser diode excitation. We recently reported a novel upconversion thulium laser that emits blue light at 77 K. In this paper additional data on this 77 K upconversion laser as well as preliminary results on the room temperature upconversion laser are presented. In these demonstrations, dye lasers were used instead of diode lasers because they were more readily available than high power semiconductor laser diodes and their wavelengths could be adjusted easily. 14 refs., 5 figs., 1 tab.

  14. Blue metal complex pigments involved in blue flower color

    PubMed Central

    Takeda, Kosaku

    2006-01-01

    The blue pigment of cornflower, protocyanin, has been investigated for a long time, but its precise structure was not entirely explained until recently. The molecular structure of the pigment was recently shown to be a metal complex of six molecules each of anthocyanin and flavone glycoside, with one ferric iron, one magnesium and two calcium ions by X-ray crystallographic analysis. The studies provided the answer to the question posed in the early part of the last century, “why is the cornflower blue and rose red when both flowers contain the same anthocyanin?” This work was achieved on the basis of the results of long years of the studies made by many researchers. In this review, the author focuses on the investigations of the blue metal complex pigments involved in the bluing of flowers, commelinin from Commelina commusis, protocyanin from Centaurea cyanus, protodelphin from Salvia patens and hydrangea blue pigment. PMID:25792777

  15. Erg cooperates with TGF-β to control mesenchymal differentiation

    PubMed Central

    Cox, Megan K.; Appelboom, Brittany L.; Ban, Ga I; Serra, Rosa

    2014-01-01

    Transforming growth factor β (TGF-β) signaling plays an integral role in skeletal development. Conditional deletion of the TGF-β type II receptor (Tgfbr2) from Type II Collagen (Col2a) expressing cells results in defects in development of the annulus fibrosus (AF) of the intervertebral disc (IVD). We previously used microarray analysis to search for marker genes of AF as well as transcription factors regulated by TGF-β during AF development. The transcription factor avian erythroblastosis virus E-26 (v-ets) oncogene related (Erg) was identified in the microarray screen as a candidate regulator of AF development. To study the effects of TGF-β on AF differentiation and the role of Erg in this process, we used mouse sclerotome grown in micromass cultures. At 0.5 ng TGF-β/ml, sclerotome cells started to express markers of AF. Regulation of Erg by TGF-β was confirmed in these cells. In addition, TGF-β soaked Affi-gel beads implanted into the axial skeleton of stage HH 25 chick embryos showed that TGF-β could induce expression of Erg mRNA in vivo. Next, an adenovirus to over-express Erg in primary sclerotome micromass cultures was generated. Over-expression of Erg led to a change in cell morphology and inhibition of differentiation into hyaline cartilage as seen by reduced Alcian blue staining and decreased Sox9 and c-Maf expression. Erg was not sufficient to induce expression of AF markers and expression of Sca1, a marker of pluripotent progenitor cells, was upregulated in Erg expressing cells. When cells that ectopically expressed Erg were treated with TGF-β, enhanced expression of specific differentiation markers was observed suggesting Erg can cooperate with TGF-β to regulate differentiation of the sclerotome. Furthermore, we showed using co-immunopreciptiation that Erg and Smad3 bind to each other suggesting a mechanism for their functional interaction. PMID:25139621

  16. Towards bottom-up nanopatterning of Prussian blue analogues

    PubMed Central

    Trannoy, Virgile; Faustini, Marco; Grosso, David; Mazerat, Sandra; Brisset, François; Dazzi, Alexandre

    2014-01-01

    Summary Ordered nanoperforated TiO2 monolayers fabricated through sol–gel chemistry were used to grow isolated particles of Prussian blue analogues (PBA). The elaboration of the TiO2/CoFe PBA nanocomposites involves five steps. The samples were characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM), infrared spectroscopy and X-ray photoelectron spectroscopy (XPS) all along the synthesis process. Selected physico-chemical parameters have been varied in order to determine the key steps of the synthesis process and to optimize it. This study is an important step towards the full control of the fabrication process. PMID:25383305

  17. Hazards of solar blue light

    SciTech Connect

    Okuno, Tsutomu

    2008-06-01

    Short-wavelength visible light (blue light) of the Sun has caused retinal damage in people who have stared fixedly at the Sun without adequate protection. The author quantified the blue-light hazard of the Sun according to the International Commission on Non-Ionizing Radiation Protection (ICNIRP) guidelines by measuring the spectral radiance of the Sun. The results showed that the exposure limit for blue light can be easily exceeded when people view the Sun and that the solar blue-light hazard generally increases with solar elevation, which is in accordance with a model of the atmospheric extinction of sunlight. Viewing the Sun can be very hazardous and therefore should be avoided except at very low solar elevations.

  18. Clarification Procedure for Gels

    NASA Technical Reports Server (NTRS)

    Barber, Patrick G.; Simpson, Norman R.

    1987-01-01

    Procedure developed to obtain transparent gels with consistencies suitable for crystal growth, by replacing sodium ions in silicate solution with potassium ions. Clarification process uses cation-exchange resin to replace sodium ions in stock solution with potassium ions, placed in 1M solution of soluble potassium salt. Slurry stirred for several hours to allow potassium ions to replace all other cations on resin. Supernatant solution decanted through filter, and beads rinsed with distilled water. Rinsing removes excess salt but leaves cation-exchange beads fully charged with potassium ions.

  19. High transparent shape memory gel

    NASA Astrophysics Data System (ADS)

    Gong, Jin; Arai, Masanori; Kabir, M. H.; Makino, Masato; Furukawa, Hidemitsu

    2014-03-01

    Gels are a new material having three-dimensional network structures of macromolecules. They possess excellent properties as swellability, high permeability and biocompatibility, and have been applied in various fields of daily life, food, medicine, architecture, and chemistry. In this study, we tried to prepare new multi-functional and high-strength gels by using Meso-Decoration (Meso-Deco), one new method of structure design at intermediate mesoscale. High-performance rigid-rod aromatic polymorphic crystals, and the functional groups of thermoreversible Diels-Alder reaction were introduced into soft gels as crosslinkable pendent chains. The functionalization and strengthening of gels can be realized by meso-decorating the gels' structure using high-performance polymorphic crystals and thermoreversible pendent chains. New gels with good mechanical properties, novel optical properties and thermal properties are expected to be developed.

  20. Foam and gel decontamination techniques

    SciTech Connect

    McGlynn, J.F.; Rankin, W.N.

    1989-01-01

    The Savannah River Site is investigating decontamination technology to improve current decontamination techniques, and thereby reduce radiation exposure to plant personnel, reduce uptake of radioactive material, and improve safety during decontamination and decommissioning activities. When decontamination chemicals are applied as foam and gels, the contact time and cleaning ability of the chemical increases. Foam and gel applicators apply foam or gel that adheres to the surface being decontaminated for periods ranging from fifteen minutes (foam) to infinite contact (gel). This equipment was started up in a cold environment. The desired foam and gel consistency was achieved, operators were trained in its proper maintenance and operation, and the foam and gel were applied to walls, ceilings, and hard to reach surfaces. 17 figs.

  1. Methylene blue related sterile endophthalmitis.

    PubMed

    Lim, A K E; Ulagantheran V, V; Siow, Y C; Lim, K S

    2008-08-01

    To report a case of methylene blue related endophthalmitis. Observational case report. Review of clinical record, photographs. A 60 year old man developed endophthalmitis after methylene blue was accidentally used to stain the anterior capsule during phacoemulsification of cataract. His left visual acuity deteriorated from 6/12 to 6/36 two weeks after the operation. Despite intensive treatment with topical and intravitreal antibiotics, his condition deteriorated. A vitrectomy and silicone oil injection eventually managed to control the progression of the disease and salvage the eye. However the visual outcome remained poor due to corneal decompensation and retinal ischemia. Both vitreous tap and vitreous biopsy were negative for any organism. Methylene blue is extremely toxic to ocular structures and should not be used intraocularly. PMID:19248701

  2. Polyoxometalate-based Supramolecular Gel

    NASA Astrophysics Data System (ADS)

    He, Peilei; Xu, Biao; Liu, Huiling; He, Su; Saleem, Faisal; Wang, Xun

    2013-05-01

    Self-assemblyings of surfactant-encapsulated Wells-Dawson polyoxometalates (SEPs) nanobuilding blocks in butanone and esters yielded supramolecular gels showing thermo and photo responsive properties. The gels can be further polymerized if unsaturated esters were used and subsequently electrospinned into nanowires and non-woven mats. The as-prepared non-woven mats have a Young's modulus as high as 542.55 MPa. It is believed that this supramolecular gel is a good platform for polyoxometalates processing.

  3. Electrically controlled polymeric gel actuators

    DOEpatents

    Adolf, Douglas B.; Shahinpoor, Mohsen; Segalman, Daniel J.; Witkowski, Walter R.

    1993-01-01

    Electrically controlled polymeric gel actuators or synthetic muscles capable of undergoing substantial expansion and contraction when subjected to changing pH environments, temperature, or solvent. The actuators employ compliant containers for the gels and their solvents. The gels employed may be cylindrical electromechanical gel fibers such as polyacrylamide fibers or a mixture of poly vinyl alcohol-polyacrylic acid arranged in a parallel aggregate and contained in an electrolytic solvent bath such as salt water. The invention includes smart, electrically activated devices exploiting this phenomenon. These devices are capable of being manipulated via active computer control as large displacement actuators for use in adaptive structure such as robots.

  4. Electrically controlled polymeric gel actuators

    DOEpatents

    Adolf, D.B.; Shahinpoor, M.; Segalman, D.J.; Witkowski, W.R.

    1993-10-05

    Electrically controlled polymeric gel actuators or synthetic muscles are described capable of undergoing substantial expansion and contraction when subjected to changing pH environments, temperature, or solvent. The actuators employ compliant containers for the gels and their solvents. The gels employed may be cylindrical electromechanical gel fibers such as polyacrylamide fibers or a mixture of poly vinyl alcohol-polyacrylic acid arranged in a parallel aggregate and contained in an electrolytic solvent bath such as salt water. The invention includes smart, electrically activated devices exploiting this phenomenon. These devices are capable of being manipulated via active computer control as large displacement actuators for use in adaptive structure such as robots. 11 figures.

  5. Gel polymer electrolytes for batteries

    DOEpatents

    Balsara, Nitash Pervez; Eitouni, Hany Basam; Gur, Ilan; Singh, Mohit; Hudson, William

    2014-11-18

    Nanostructured gel polymer electrolytes that have both high ionic conductivity and high mechanical strength are disclosed. The electrolytes have at least two domains--one domain contains an ionically-conductive gel polymer and the other domain contains a rigid polymer that provides structure for the electrolyte. The domains are formed by block copolymers. The first block provides a polymer matrix that may or may not be conductive on by itself, but that can soak up a liquid electrolyte, thereby making a gel. An exemplary nanostructured gel polymer electrolyte has an ionic conductivity of at least 1.times.10.sup.-4 S cm.sup.-1 at 25.degree. C.

  6. Colloidal thermoresponsive gel forming hybrids.

    PubMed

    Liu, Ruixue; Tirelli, Nicola; Cellesi, Francesco; Saunders, Brian R

    2010-09-15

    Colloidal hybrids comprise organic and inorganic components and are attracting considerable attention in the literature. Recently, we reported hybrid anisotropic microsheets that formed thermoresponsive gels in polymer solutions [Liu et al., Langmuir, 25, 490, 2009]. Here, we investigate the composition and properties of these hybrid colloids themselves in detail for the first time. Three different cationic PNIPAm (N-isopropylacrylamide) graft copolymers and two inorganic nanoparticle types (laponite and Ludox silica) were used to prepare a range of hybrids. Anisotropic microsheets only formed when laponite particles were added to the copolymer implying directed self-assembly. Aqueous dispersions of the microsheets spontaneously formed gels at room temperature and these gels were thermoresponsive. They represent a new class of gel forming colloid and are termed thermoresponsive gel forming hybrids. The compositions of the hybrids were determined from thermogravimetric analysis and those that gave gel forming behaviour identified. Variable-temperature rheology experiments showed that the elasticity of the gels increased linearly with temperature. The reversibility of the thermally-triggered changes in gel elasticity was investigated. The concentration dependence of the rheology data was well described by elastic percolation scaling theory and the data could be collapsed onto a master curve. The concentration exponent for the elastic modulus was 2.5. The strong attractive interactions that exist between the dispersed gel forming hybrids was demonstrated by the formation of stable thermoresponsive hybrid hydrogels through casting of hybrid dispersions. PMID:20561633

  7. The blue-collar brain.

    PubMed

    Van Orden, Guy; Hollis, Geoff; Wallot, Sebastian

    2012-01-01

    Much effort has gone into elucidating control of the body by the brain, less so the role of the body in controlling the brain. This essay develops the idea that the brain does a great deal of work in the service of behavior that is controlled by the body, a blue-collar role compared to the white-collar control exercised by the body. The argument that supports a blue-collar role for the brain is also consistent with recent discoveries clarifying the white-collar role of synergies across the body's tensegrity structure, and the evidence of critical phenomena in brain and behavior. PMID:22719730

  8. Blue-green upconversion laser

    DOEpatents

    Nguyen, D.C.; Faulkner, G.E.

    1990-08-14

    A blue-green laser (450--550 nm) uses a host crystal doped with Tm[sup 3+]. The Tm[sup 3+] is excited through upconversion by a red pumping laser and an IR pumping laser to a state which transitions to a relatively lower energy level through emissions in the blue-green band, e.g., 450.20 nm at 75 K. The exciting laser may be tunable dye lasers or may be solid-state semiconductor laser, e.g., GaAlAs and InGaAlP. 3 figs.

  9. Crater Lake: blue through time

    USGS Publications Warehouse

    Larson, Gary L.; Buktenica, Mark; Collier, Robert

    2003-01-01

    Blue is the color of constancy, hence the term true blue. The unearthly blueness of Crater Lake reflects its pristine character and gives scientists a focal point for studying human impacts on aquatic environments over long periods of time. Scientists with the U.S. Geological Survey (USGS), National Park Service, and Oregon State University have systematically studied the lake for the last two decades. Long-term monitoring of this lake is a priority of Crater Lake National Park and will continue far into the future.

  10. The Blue-Collar Brain

    PubMed Central

    Van Orden, Guy; Hollis, Geoff; Wallot, Sebastian

    2012-01-01

    Much effort has gone into elucidating control of the body by the brain, less so the role of the body in controlling the brain. This essay develops the idea that the brain does a great deal of work in the service of behavior that is controlled by the body, a blue-collar role compared to the white-collar control exercised by the body. The argument that supports a blue-collar role for the brain is also consistent with recent discoveries clarifying the white-collar role of synergies across the body’s tensegrity structure, and the evidence of critical phenomena in brain and behavior. PMID:22719730

  11. Blue-green upconversion laser

    DOEpatents

    Nguyen, Dinh C.; Faulkner, George E.

    1990-01-01

    A blue-green laser (450-550 nm) uses a host crystal doped with Tm.sup.3+. The Tm.sup.+ is excited through upconversion by a red pumping laser and an IR pumping laser to a state which transitions to a relatively lower energy level through emissions in the blue-green band, e.g., 450.20 nm at 75 K. The exciting laser may be tunable dye lasers or may be solid-state semiconductor laser, e.g., GaAlAs and InGaAlP.

  12. Blue light emitting thiogallate phosphor

    DOEpatents

    Dye, Robert C.; Smith, David C.; King, Christopher N.; Tuenge, Richard T.

    1998-01-01

    A crystalline blue emitting thiogallate phosphor of the formula RGa.sub.2 S.sub.4 :Ce.sub.x where R is selected from the group consisting of calcium, strontium, barium and zinc, and x is from about 1 to 10 atomic percent, the phosphor characterized as having a crystalline microstructure on the size order of from about 100 .ANG. to about 10,000 .ANG. is provided together with a process of preparing a crystalline blue emitting thiogallate phosphor by depositing on a substrate by CVD and resultant thin film electroluminescent devices including a layer of such deposited phosphor on an ordinary glass substrate.

  13. Molybdate Reduction to Molybdenum Blue by an Antarctic Bacterium

    PubMed Central

    Ahmad, S. A.; Shukor, M. Y.; Shamaan, N. A.; Mac Cormack, W. P.; Syed, M. A.

    2013-01-01

    A molybdenum-reducing bacterium from Antarctica has been isolated. The bacterium converts sodium molybdate or Mo6+ to molybdenum blue (Mo-blue). Electron donors such as glucose, sucrose, fructose, and lactose supported molybdate reduction. Ammonium sulphate was the best nitrogen source for molybdate reduction. Optimal conditions for molybdate reduction were between 30 and 50 mM molybdate, between 15 and 20°C, and initial pH between 6.5 and 7.5. The Mo-blue produced had a unique absorption spectrum with a peak maximum at 865 nm and a shoulder at 710 nm. Respiratory inhibitors such as antimycin A, sodium azide, potassium cyanide, and rotenone failed to inhibit the reducing activity. The Mo-reducing enzyme was partially purified using ion exchange and gel filtration chromatography. The partially purified enzyme showed optimal pH and temperature for activity at 6.0 and 20°C, respectively. Metal ions such as cadmium, chromium, copper, silver, lead, and mercury caused more than 95% inhibition of the molybdenum-reducing activity at 0.1 mM. The isolate was tentatively identified as Pseudomonas sp. strain DRY1 based on partial 16s rDNA molecular phylogenetic assessment and the Biolog microbial identification system. The characteristics of this strain would make it very useful in bioremediation works in the polar and temperate countries. PMID:24381945

  14. Molybdate reduction to molybdenum blue by an Antarctic bacterium.

    PubMed

    Ahmad, S A; Shukor, M Y; Shamaan, N A; Mac Cormack, W P; Syed, M A

    2013-01-01

    A molybdenum-reducing bacterium from Antarctica has been isolated. The bacterium converts sodium molybdate or Mo⁶⁺ to molybdenum blue (Mo-blue). Electron donors such as glucose, sucrose, fructose, and lactose supported molybdate reduction. Ammonium sulphate was the best nitrogen source for molybdate reduction. Optimal conditions for molybdate reduction were between 30 and 50 mM molybdate, between 15 and 20°C, and initial pH between 6.5 and 7.5. The Mo-blue produced had a unique absorption spectrum with a peak maximum at 865 nm and a shoulder at 710 nm. Respiratory inhibitors such as antimycin A, sodium azide, potassium cyanide, and rotenone failed to inhibit the reducing activity. The Mo-reducing enzyme was partially purified using ion exchange and gel filtration chromatography. The partially purified enzyme showed optimal pH and temperature for activity at 6.0 and 20°C, respectively. Metal ions such as cadmium, chromium, copper, silver, lead, and mercury caused more than 95% inhibition of the molybdenum-reducing activity at 0.1 mM. The isolate was tentatively identified as Pseudomonas sp. strain DRY1 based on partial 16s rDNA molecular phylogenetic assessment and the Biolog microbial identification system. The characteristics of this strain would make it very useful in bioremediation works in the polar and temperate countries. PMID:24381945

  15. A genipin-gelatin gel dosimeter for radiation processing

    NASA Astrophysics Data System (ADS)

    Davies, J. B.; Bosi, S. G.; Baldock, C.

    2012-08-01

    Genipin, a fruit extract from Gardenia jasminoides Ellis, forms cross-links in solutions of gelatin, to form a blue hydrogel that bleaches quantitatively upon irradiation and the colour change can be measured with a spectrophotometer. With the addition of sulphuric acid this dosimeter is sufficiently sensitive for quality assurance of radiotherapy level dosimetry. Without sulphuric acid the gel has a reduced sensitivity and responds linearly with dose between 100 and 1000 Gy, making it potentially useful as a dosimeter for radiation processing applications such as the phytosanitary irradiation treatment of food. We investigated the dose response characteristics of this new formulation and found that the darker gels are more sensitive to dose and have a reduced uncertainty.

  16. Homogeneity of gels and gel-derived glasses

    NASA Technical Reports Server (NTRS)

    Mukherjee, S. P.

    1984-01-01

    The significance and implications of gel preparation procedures in controlling the homogeneity of multicomponent oxide gels are discussed. The role of physicochemical factors such as the structure and chemical reactivities of alkoxides, the formation of double-metal alkoxides, and the nature of solvent(s) are critically analyzed in the context of homogeneity of gels during gelation. Three procedures for preparing gels in the SiO2-B2O3-Na2O system are examined in the context of cation distribution. Light scattering results for glasses in the SiO2-B2O3-Na2O system prepared by both the gel technique and the conventional technique are examined.

  17. Blue light hazard and aniridia.

    PubMed Central

    Abadi, R. V.; Dickinson, C. M.

    1985-01-01

    The fundi of three patients with aniridia were photographed with a 470 nm illuminating light source. No apparent change in contrast was observable throughout the macular region. This would suggest an absence of the macular pigment. The likelihood of aniridics being more susceptible than normal persons to blue light damage is discussed. Images PMID:3978071

  18. Singing' the Black and Blues

    ERIC Educational Resources Information Center

    Fisher, Diane

    2004-01-01

    It is so obvious that the sky is blue in the daytime and black at night, but it took the smartest humans thousands of years of observation, thought, discussion, conjecture, and analysis to finally come up with answers that make scientific sense as to why the sky is these colors. This article discusses light and the scientific research…

  19. Flying the Blue Ribbon Flag.

    ERIC Educational Resources Information Center

    McDaniel, Lynda

    2000-01-01

    Guntersville Elementary School, a preK-2 school in Alabama, earned the U.S. Department of Education's Blue Ribbon Schools award through creative programs addressing school readiness, parent education, and the need for extended-day and summer activities; a progressive curriculum; and various community partnerships. (SV)

  20. The Taos Blue Lake Ceremony.

    ERIC Educational Resources Information Center

    Bodine, John J.

    1988-01-01

    Describes the Blue Lake Ceremony of the Taos Pueblo Indians of New Mexico. Reproduces the 1906 account of the ceremony by anthropologist Matilda Coxe Stevenson and notes modern verification and change. Discusses the importance of this annual August pilgrimage and initiation rite to the preservation of Taos culture. (SV)

  1. Nobel Prize for blue LEDs

    NASA Astrophysics Data System (ADS)

    Kraftmakher, Yaakov

    2015-05-01

    A brief review of lighting technologies is presented. Unavoidable restrictions for incandescent light bulbs caused by the Planck distribution and properties of the human eye are illustrated. The efficiency and luminous efficacy of thermal radiation are calculated for various temperatures; the results clearly show the limitations for thermal radiators. The only way to overcome these limitations is using non-thermal radiators, such as fluorescent lamps and light-emitting diodes (LEDs). Unique advantages of LEDs undoubtedly made a revolution in this field. A crucial element of this progress is the blue LEDs (Nobel Prize 2014). Some experiments with a blue and a green LED are described: (i) the luminescence triggered in a green-yellow phosphor inside a white LED by the blue LED; (ii) radiant spectra and ‘efficiency droop’ in the LEDs; (iii) modulation of the blue LED up to 4 MHz; and (iv) the h/e ratio from the turn-on voltage of the green LED. The experiments are suitable for undergraduate laboratories and usable as classroom demonstrations.

  2. Antimicrobial Graft Copolymer Gels.

    PubMed

    Harvey, Amanda C; Madsen, Jeppe; Douglas, C W Ian; MacNeil, Sheila; Armes, Steven P

    2016-08-01

    In view of the growing worldwide rise in microbial resistance, there is considerable interest in designing new antimicrobial copolymers. The aim of the current study was to investigate the relationship between antimicrobial activity and copolymer composition/architecture to gain a better understanding of their mechanism of action. Specifically, the antibacterial activity of several copolymers based on 2-(methacryloyloxy)ethyl phosphorylcholine [MPC] and 2-hydroxypropyl methacrylate (HPMA) toward Staphylococcus aureus was examined. Both block and graft copolymers were synthesized using either atom transfer radical polymerization or reversible addition-fragmentation chain transfer polymerization and characterized via (1)H NMR, gel permeation chromatography, rheology, and surface tensiometry. Antimicrobial activity was assessed using a range of well-known assays, including direct contact, live/dead staining, and the release of lactate dehydrogenase (LDH), while transmission electron microscopy was used to study the morphology of the bacteria before and after the addition of various copolymers. As expected, PMPC homopolymer was biocompatible but possessed no discernible antimicrobial activity. PMPC-based graft copolymers comprising PHPMA side chains (i.e. PMPC-g-PHPMA) significantly reduced both bacterial growth and viability. In contrast, a PMPC-PHPMA diblock copolymer comprising a PMPC stabilizer block and a hydrophobic core-forming PHPMA block did not exhibit any antimicrobial activity, although it did form a biocompatible worm gel. Surface tensiometry studies and LDH release assays suggest that the PMPC-g-PHPMA graft copolymer exhibits surfactant-like activity. Thus, the observed antimicrobial activity is likely to be the result of the weakly hydrophobic PHPMA chains penetrating (and hence rupturing) the bacterial membrane. PMID:27409712

  3. Crystallization of steroids in gels

    NASA Astrophysics Data System (ADS)

    Kalkura, S. Narayana; Devanarayanan, S.

    1991-03-01

    The crystal growth and characterization of certain steriods, viz., cholesterol, cholesteryl acetate, β-sitosterol, progesterone and testosterone, in a silica gel medium is discussed. The present study shows that the single test tube diffusion method can be used to grow crystals of steroids in a silica gel medium by the reduction of steroid solubility.

  4. Nanocrystal/sol-gel nanocomposites

    DOEpatents

    Petruska, Melissa A.; Klimov, Victor L.

    2012-06-12

    The present invention is directed to solid composites including colloidal nanocrystals within a sol-gel host or matrix and to processes of forming such solid composites. The present invention is further directed to alcohol soluble colloidal nanocrystals useful in formation of sol-gel based solid composites

  5. Nanocrystal/sol-gel nanocomposites

    DOEpatents

    Petruska, Melissa A.; Klimov, Victor L.

    2007-06-05

    The present invention is directed to solid composites including colloidal nanocrystals within a sol-gel host or matrix and to processes of forming such solid composites. The present invention is further directed to alcohol soluble colloidal nanocrystals useful in formation of sol-gel based solid composites.

  6. Sucrose release from polysaccharide gels.

    PubMed

    Nishinari, Katsuyoshi; Fang, Yapeng

    2016-05-18

    Sucrose release from polysaccharide gels has been studied extensively because it is expected to be useful in understanding flavour release from solid foods and to find a new processing method which produces more palatable and healthier foods. We provide an overview of the release of sucrose and other sugars from gels of agar and related polysaccharides. The addition of sucrose to agar solutions leads to the increase in transparency of the resulting gels and the decrease in syneresis, which is attributed to the decrease in mesh size in gels. The syneresis occurring in the quiescent condition and fluid release induced by compression is discussed. The relationship between the sugar release and the structural, rheological and thermal properties of gels is also discussed. Finally, the future research direction is proposed. PMID:26952168

  7. Porous alumina scaffold produced by sol-gel combined polymeric sponge method

    NASA Astrophysics Data System (ADS)

    Hasmaliza, M.; Fazliah, M. N.; Shafinaz, R. J.

    2012-09-01

    Sol gel is a novel method used to produce high purity alumina with nanometric scale. In this study, three-dimensional porous alumina scaffold was produced using sol-gel polymeric sponge method. Briefly, sol gel alumina was prepared by evaporation and polymeric sponge cut to designated sizes were immersed in the sol gel followed by sintering at 1250 and 1550°C. In order to study the cell interaction, the porous alumina scaffold was sterilized using autoclave prior to Human Mesenchymal Stem Cells (HMSCs) seeding on the scaffold and the cell proliferation was assessed by alamarBlue® assay. SEM results showed that during the 21 day period, HMSCs were able to attach on the scaffold surface and the interconnecting pores while maintaining its proliferation. These findings suggested the potential use of the porous alumina produced as a scaffold for implantation procedure.

  8. Plutonium Decontamination Using CBI Decon Gel 1101 in Highly Contaminated and Unique Areas at LLNL

    SciTech Connect

    Sutton, M; Fischer, R P; Thoet, M M; O'Neill, M; Edgington, G

    2008-06-09

    A highly contaminated glove-box at LLNL containing plutonium was decontaminated using a strippable decontamination gel. 6 x 12 inch quadrants were mapped out on each of the surfaces. The gel was applied to various surfaces inside the glove-box and was allowed to cure. The radioactivity in each quadrant was measured using a LLNL Blue Alpha meter with a 1.5 inch standoff distance. The results showed decontamination factors of 130 and 210 on cast steel and Lexan{reg_sign} surfaces respectively after several applications. The gel also absorbed more than 91% of the radiation emitted from the surfaces during gel curing. The removed strippable film was analyzed by neutron multiplicity counting and gamma spectroscopy, yielding relative mass information and radioisotopic composition respectively.

  9. Tubular structured hierarchical mesoporous titania material derived from natural cellulosic substances and application as photocatalyst for degradation of methylene blue

    SciTech Connect

    Huang, Haiqing; Liu, Xiaoyan; Huang, Jianguo

    2011-11-15

    Graphical abstract: Bio-inspired, tubular structured hierarchical mesoporous titania material with high photocatalytic activity under UV light was fabricated employing natural cellulosic substance (cotton) as hard template and cetyltrimethylammonium bromide (CTAB) surfactant as soft template using a one-pot sol-gel method. Highlights: {yields} Tubular structured mesoporous titania material was fabricated by sol-gel method. {yields} The titania material faithfully recorded the hierarchical structure of the template substrate (cotton). {yields} The titania material exhibited high photocatalytic activity in decomposition of methylene blue. -- Abstract: Bio-inspired, tubular structured hierarchical mesoporous titania material was designed and fabricated employing natural cellulosic substance (cotton) as hard template and cetyltrimethylammonium bromide (CTAB) surfactant as soft template by one-pot sol-gel method. The tubular structured hierarchical mesoporous titania material processes large specific surface area (40.23 m{sup 2}/g) and shows high photocatalytic activity in the photodegradation of methylene blue under UV light irradiation.

  10. The Blues Poetry of Langston Hughes

    ERIC Educational Resources Information Center

    Waldron, Edward E.

    1971-01-01

    The author discusses the criteria of the blues as an American art form. He then shows how Langston Hughes captures the mood, the feeling, the rhythm and the impact of the blues in his poetry. (Author/LF)

  11. Practical utility of the blue spectral region

    NASA Technical Reports Server (NTRS)

    Ross, D. S.

    1972-01-01

    Some aspects of multispectral photography in the blue region are discussed briefly, and sample images are submitted to demonstrate the potential utility of the blue multispectral record for oceanography.

  12. 21 CFR 73.50 - Ultramarine blue.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... ultramarine blue is a blue pigment obtained by calcining a mixture of kaolin, sulfur, sodium carbonate, and... order to vary the shade. The pigment is a complex sodium aluminum sulfo-silicate having the...

  13. 21 CFR 73.50 - Ultramarine blue.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... ultramarine blue is a blue pigment obtained by calcining a mixture of kaolin, sulfur, sodium carbonate, and... order to vary the shade. The pigment is a complex sodium aluminum sulfo-silicate having the...

  14. 21 CFR 73.50 - Ultramarine blue.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... ultramarine blue is a blue pigment obtained by calcining a mixture of kaolin, sulfur, sodium carbonate, and... order to vary the shade. The pigment is a complex sodium aluminum sulfo-silicate having the...

  15. 21 CFR 73.50 - Ultramarine blue.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... ultramarine blue is a blue pigment obtained by calcining a mixture of kaolin, sulfur, sodium carbonate, and... order to vary the shade. The pigment is a complex sodium aluminum sulfo-silicate having the...

  16. 21 CFR 73.50 - Ultramarine blue.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... ultramarine blue is a blue pigment obtained by calcining a mixture of kaolin, sulfur, sodium carbonate, and... order to vary the shade. The pigment is a complex sodium aluminum sulfo-silicate having the...

  17. Bouncing gel balls: Impact of soft gels onto rigid surface

    NASA Astrophysics Data System (ADS)

    Tanaka, Y.; Yamazaki, Y.; Okumura, K.

    2003-07-01

    After being thrown onto a solid substrate, very soft spherical gels bounce repeatedly. Separate rheological measurements suggest that these balls can be treated as nearly elastic. The Hertz contact deformation expected in the static (elastic) limit was observed only at very small impact velocities. For larger velocities, the gel ball deformed into flattened forms like a pancake. We measured the size of the gel balls at the maximal deformation and the contact time as a function of velocities for samples different in the original spherical radius and the Young modulus. The experimental results revealed a number of scaling relations. To interpret these relations, we developed scaling arguments to propose a physical picture.

  18. On Seeing Reddish Green and Yellowish Blue.

    ERIC Educational Resources Information Center

    Crane, Hewitt D.; Piantanida, Thomas P.

    1983-01-01

    Stabilization of the retinal image of the boundary between a pair of red/green or yellow/blue stripes, but not their outer edges, results in the entire region being perceived simultaneously as both red/green or yellow/blue. This suggests that the percepts of reddish-green/yellowish-blue apparently are possible in corticocortical color vision…

  19. 75 FR 65525 - Anthem Blue Cross Blue Shield, Claim Management Services, Inc. Operations, a Division of...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-25

    ... on September 3, 2010 (75 FR 54187). The workers supply claims processing services and customer... Employment and Training Administration Anthem Blue Cross Blue Shield, Claim Management Services, Inc... Adjustment Assistance (TAA), applicable to workers and former workers of Anthem Blue Cross Blue Shield,...

  20. Cadmium-binding proteins from blue crabs (Callinectes sapidus) environmentally exposed to cadmium

    SciTech Connect

    Wiedow, M.A.; Kneip, T.J.; Garte, S.J.

    1982-06-01

    Two heat-stable (90/sup 0/C) cadmium-binding proteins were isolated from the hepatopancreas of Hudson River blue crabs (Callinectes sapidus) by Sephadex G-75 gel filtration chromatography. These proteins have molecular weights of 10,600 and 9,400, and ultraviolet absorbance ratios at 250/280 nm of 12.4 and 5.4, respectively. Repeated freezing and thawing and prolonged (3-6 weeks) storage resulted in protein degradation or loss of Cd-binding activity. These proteins were induced by laboratory injection of CdCl/sub 2/ in blue crabs from pristine (Chesapeake Bay) areas; however, injection of CdCl/sub 2/ into Hudson River animals yielded anomalous chromatography profiles. Cadmium-binding proteins were also identified in blue crab thoracic muscle and gill. The possibility is discussed that these proteins are a type of metallothionein and could contribute to the human toxicity of this cadmium-contaminated edible crustacean.

  1. Mechanical Failure in Colloidal Gels

    NASA Astrophysics Data System (ADS)

    Kodger, Thomas Edward

    When colloidal particles in a dispersion are made attractive, they aggregate into fractal clusters which grow to form a space-spanning network, or gel, even at low volume fractions. These gels are crucial to the rheological behavior of many personal care, food products and dispersion-based paints. The mechanical stability of these products relies on the stability of the colloidal gel network which acts as a scaffold to provide these products with desired mechanical properties and to prevent gravitational sedimentation of the dispersed components. Understanding the mechanical stability of such colloidal gels is thus of crucial importance to predict and control the properties of many soft solids. Once a colloidal gel forms, the heterogeneous structure bonded through weak physical interactions, is immediately subject to body forces, such as gravity, surface forces, such as adhesion to a container walls and shear forces; the interplay of these forces acting on the gel determines its stability. Even in the absence of external stresses, colloidal gels undergo internal rearrangements within the network that may cause the network structure to evolve gradually, in processes known as aging or coarsening or fail catastrophically, in a mechanical instability known as syneresis. Studying gel stability in the laboratory requires model colloidal system which may be tuned to eliminate these body or endogenous forces systematically. Using existing chemistry, I developed several systems to study delayed yielding by eliminating gravitational stresses through density matching and cyclic heating to induce attraction; and to study syneresis by eliminating adhesion to the container walls, altering the contact forces between colloids, and again, inducing gelation through heating. These results elucidate the varied yet concomitant mechanisms by which colloidal gels may locally or globally yield, but then reform due to the nature of the physical, or non-covalent, interactions which form

  2. Status of Blue Ridge Reservoir

    SciTech Connect

    Not Available

    1990-09-01

    This is one in a series of reports prepared by the Tennessee Valley Authority (TVA) for those interested in the conditions of TVA reservoirs. This overview of Blue Ridge Reservoir summarizes reservoir and watershed characteristics, reservoir uses and use impairments, water quality and aquatic biological conditions, and activities of reservoir management agencies. This information was extracted from the most current reports and data available, as well as interview with water resource professionals in various federal, state, and local agencies. Blue Ridge Reservoir is a single-purpose hydropower generating project. When consistent with this primary objective, the reservoir is also operated to benefit secondary objectives including water quality, recreation, fish and aquatic habitat, development of shoreline, aesthetic quality, and other public and private uses that support overall regional economic growth and development. 8 refs., 1 fig.

  3. The Physics of the Blues

    NASA Astrophysics Data System (ADS)

    Gibson, J. Murray

    2009-03-01

    In looking at the commonalities between music and science, one sees that the musician's palette is based on the principles of physics. The pitch of a musical note is determined by the frequency of the sound wave. The scales that musicians use to create and play music can be viewed as a set of rules. What makes music interesting is how musicians develop those rules and create ambiguity with them. I will discuss the evolution of western musical scales in this context. As a particular example, ``Blue'' notes are very harmonic notes that are missing from the equal temperament scale. The techniques of piano blues and jazz represent the melding of African and Western music into something totally new and exciting. Live keyboard demonstrations will be used. Beyond any redeeming entertainment value the talk will emphasize the serious connections between science and art in music. Nevertheless tips will be accepted.

  4. Food habits of blue grouse

    USGS Publications Warehouse

    Stewart, R.E.

    1944-01-01

    The food habits of Blue Grouse vary from a simple winter diet that is made up predominantly of coniferous needles to a complex diet during the summer months, characterized by great variety of foods including green leaves, fruits and seeds, flowers, animal matter and coniferous needles. The spring and fall, which represent the transition periods between these two, are characterized by feeding habits that are generally intermediate. The diets of the two species of Blue Grouse, Dendrugapus obscurus and Dendragapus juliginosus, are quite similar as far as major types of food are concerned, but they differ considerably in the species that are taken. Such differences reflect differences in the vegetation within the ecologic and geographic ranges occupied by the two species.

  5. Ol' Blue Eyes, in Focus

    ERIC Educational Resources Information Center

    Nelson, Michael

    2009-01-01

    Scholarly books with "identity" and "culture" in the title have loomed large on academic publishing lists for several years. Scholarly books with "Sinatra" in the title are a more recent phenomenon. Despite his six-decade career as the Voice (the 1940s), the Chairman of the Board (the 50s and 60s), and Ol' Blue Eyes (the 70s through his death, in…

  6. Polyoxometalate-based Supramolecular Gel

    PubMed Central

    He, Peilei; Xu, Biao; Liu, Huiling; He, Su; Saleem, Faisal; Wang, Xun

    2013-01-01

    Self-assemblyings of surfactant-encapsulated Wells-Dawson polyoxometalates (SEPs) nanobuilding blocks in butanone and esters yielded supramolecular gels showing thermo and photo responsive properties. The gels can be further polymerized if unsaturated esters were used and subsequently electrospinned into nanowires and non-woven mats. The as-prepared non-woven mats have a Young's modulus as high as 542.55 MPa. It is believed that this supramolecular gel is a good platform for polyoxometalates processing. PMID:23666013

  7. Adhesive, elastomeric gel impregnating composition

    DOEpatents

    Shaw, David Glenn; Pollard, John Randolph; Brooks, Robert Aubrey

    2002-01-01

    An improved capacitor roll with alternating film and foil layers is impregnated with an adhesive, elastomeric gel composition. The gel composition is a blend of a plasticizer, a polyol, a maleic anhydride that reacts with the polyol to form a polyester, and a catalyst for the reaction. The impregnant composition is introduced to the film and foil layers while still in a liquid form and then pressure is applied to aid with impregnation. The impregnant composition is cured to form the adhesive, elastomeric gel. Pressure is maintained during curing.

  8. Models of Individual Blue Stragglers

    NASA Astrophysics Data System (ADS)

    Sills, Alison

    This chapter describes the current state of models of individual blue stragglers. Stellar collisions, binary mergers (or coalescence), and partial or ongoing mass transfer have all been studied in some detail. The products of stellar collisions retain memory of their parent stars and are not fully mixed. Very high initial rotation rates must be reduced by an unknown process to allow the stars to collapse to the main sequence. The more massive collision products have shorter lifetimes than normal stars of the same mass, while products between low mass stars are long-lived and look very much like normal stars of their mass. Mass transfer can result in a merger, or can produce another binary system with a blue straggler and the remnant of the original primary. The products of binary mass transfer cover a larger portion of the colour-magnitude diagram than collision products for two reasons: there are more possible configurations which produce blue stragglers, and there are differing contributions to the blended light of the system. The effects of rotation may be substantial in both collision and merger products, and could result in significant mixing unless angular momentum is lost shortly after the formation event. Surface abundances may provide ways to distinguish between the formation mechanisms, but care must be taken to model the various mixing mechanisms properly before drawing strong conclusions. Avenues for future work are outlined.

  9. The Cryptochrome Blue Light Receptors.

    PubMed

    Yu, Xuhong; Liu, Hongtao; Klejnot, John; Lin, Chentao

    2010-09-23

    Cryptochromes are photolyase-like blue light receptors originally discovered in Arabidopsis but later found in other plants, microbes, and animals. Arabidopsis has two cryptochromes, CRY1 and CRY2, which mediate primarily blue light inhibition of hypocotyl elongation and photoperiodic control of floral initiation, respectively. In addition, cryptochromes also regulate over a dozen other light responses, including circadian rhythms, tropic growth, stomata opening, guard cell development, root development, bacterial and viral pathogen responses, abiotic stress responses, cell cycles, programmed cell death, apical dominance, fruit and ovule development, seed dormancy, and magnetoreception. Cryptochromes have two domains, the N-terminal PHR (Photolyase-Homologous Region) domain that bind the chromophore FAD (flavin adenine dinucleotide), and the CCE (CRY C-terminal Extension) domain that appears intrinsically unstructured but critical to the function and regulation of cryptochromes. Most cryptochromes accumulate in the nucleus, and they undergo blue light-dependent phosphorylation or ubiquitination. It is hypothesized that photons excite electrons of the flavin molecule, resulting in redox reaction or circular electron shuttle and conformational changes of the photoreceptors. The photoexcited cryptochrome are phosphorylated to adopt an open conformation, which interacts with signaling partner proteins to alter gene expression at both transcriptional and posttranslational levels and consequently the metabolic and developmental programs of plants. PMID:21841916

  10. Uncovering Blue Diffuse Dwarf Galaxies

    NASA Astrophysics Data System (ADS)

    James, Bethan; Koposov, Sergey; Stark, Daniel; Belokurov, Vasily; Pettini, Max; Olszewski, Edward W.

    2015-01-01

    Extremely metal-poor galaxies (XMPs) and the star-formation within their chemically pristine environments are fundamental to our understanding of the galaxy formation process at early times. However, traditional emission-line surveys detect only the brightest metal-poor galaxies where star-formation occurs in compact, starbursting environments, and thereby give us only a partial view of the dwarf galaxy population. To avoid such biases, we have developed a new search algorithm based on the morphological, rather then spectral, properties of XMPs and have applied to the Sloan Digital Sky Survey database of images. Using this novel approach, we have discovered ~100 previously undetected, faint blue galaxies, each with isolated HII regions embedded in a diffuse continuum. In this talk I will present the first results from follow-up optical spectroscopy of this sample, which reveals these blue diffuse dwarfs (BDDs) to be young, very metal-poor and actively forming stars despite their intrinsically low luminosities. I will present evidence showing that BDDs appear to bridge the gap between quiescent dwarf irregular (dIrr) galaxies and blue compact galaxies (BCDs) and as such offer an ideal opportunity to assess how star-formation occurs in more `normal' metal-poor systems.

  11. Tetrapeptide-coumarin conjugate 3D networks based on hydrogen-bonded charge transfer complexes: gel formation and dye release.

    PubMed

    Guo, Zongxia; Gong, Ruiying; Jiang, Yi; Wan, Xiaobo

    2015-08-14

    Oligopeptide-based derivatives are important synthons for bio-based functional materials. In this article, a Gly-(L-Val)-Gly-(L-Val)-coumarin (GVGV-Cou) conjugate was synthesized, which forms 3D networks in ethanol. The gel nanostructures were characterized by UV-vis spectroscopy, FT-IR spectroscopy, X-ray diffraction (XRD), SEM and TEM. It is suggested that the formation of charge transfer (CT) complexes between the coumarin moieties is the main driving force for the gel formation. The capability of the gel to encapsulate and release dyes was explored. Both Congo Red (CR) and Methylene Blue (MB) can be trapped in the CT gel matrix and released over time. The present gel might be used as a functional soft material for guest encapsulation and release. PMID:26138931

  12. Optical and NMR dose response of N-isopropylacrylamide normoxic polymer gel for radiation therapy dosimetry

    PubMed Central

    Mesbahi, Asghar; Jafarzadeh, Vahid; Gharehaghaji, Nahideh

    2012-01-01

    Background Application of less toxic normoxic polymer gel of N-isopropyl acrylamide (NIPAM) for radiation therapy has been studied in recent years. Aim In the current study the optical and NMR properties of NIPAM were studied for radiation therapy dosimetry application. Materials and methods NIPAM normoxic polymer gel was prepared and irradiated by 9 MV photon beam of a medical linac. The optical absorbance was measured using a conventional laboratory spectrophotometer in different wavelengths ranging from 390 to 860 nm. R2 measurements of NIPAM gels were performed using a 1.5 T scanner and R2–dose curve was obtained. Results Our results showed R2 dose sensitivity of 0.193 ± 0.01 s−1 Gy−1 for NIPAM gel. Both R2 and optical absorbance showed a linear relationship with dose from 1.5 to 11 Gy for NIPAM gel dosimeter. Moreover, absorbance–dose response varied considerably with light wavelength and highest sensitivity was seen for the blue part of the spectrum. Conclusion Our results showed that both optical and NMR approaches have acceptable sensitivity and accuracy for dose determination with NIPAM gel. However, for optical reading of the gel, utilization of an optimum optical wavelength is recommended. PMID:24377016

  13. Localized Eruptive Blue Nevi after Herpes Zoster

    PubMed Central

    Colson, Fany; Arrese, Jorge E.; Nikkels, Arjen F.

    2016-01-01

    A 52-year-old White man presented with a dozen small, well-restricted, punctiform, asymptomatic, blue-gray macules on the left shoulder. A few months earlier, he had been treated with oral acyclovir for herpes zoster (HZ) affecting the left C7–C8 dermatomes. All the blue macules appeared over a short period of time and then remained stable. The patient had not experienced any previous trauma or had tattooing in this anatomical region. The clinical diagnosis suggested blue nevi. Dermatoscopy revealed small, well-limited, dark-blue, compact, homogeneous areas evoking dermal blue nevi. An excisional biopsy was performed and the histological examination confirmed a blue nevus. As far as we are aware of, this is the first report of eruptive blue nevi following HZ, and it should be included in the differential diagnosis of zosteriform dermatoses responding to an isotopic pathway. In addition, a brief review concerning eruptive nevi is presented. PMID:27462219

  14. Inflation and alternatives with blue tensor spectra

    SciTech Connect

    Wang, Yi; Xue, Wei E-mail: wei.xue@sissa.it

    2014-10-01

    We study the tilt of the primordial gravitational waves spectrum. A hint of blue tilt is shown from analyzing the BICEP2 and POLARBEAR data. Motivated by this, we explore the possibilities of blue tensor spectra from the very early universe cosmology models, including null energy condition violating inflation, inflation with general initial conditions, and string gas cosmology, etc. For the simplest G-inflation, blue tensor spectrum also implies blue scalar spectrum. In general, the inflation models with blue tensor spectra indicate large non-Gaussianities. On the other hand, string gas cosmology predicts blue tensor spectrum with highly Gaussian fluctuations. If further experiments do confirm the blue tensor spectrum, non-Gaussianity becomes a distinguishing test between inflation and alternatives.

  15. Dynamics of a DNA Gel

    NASA Astrophysics Data System (ADS)

    Adhikari, Ramesh; Bhattacharya, Aniket; Dogariu, Aristide

    We study in silico the properties of a gel consisting of DNA strands (modeled as semi-flexible chains) and linkers of varying flexibility, length, and topology. These linkers are envisioned and modeled as active components with additional attributes so as to mimic properties of a synthetic DNA gel containing motor proteins. We use Brownian dynamics to directly obtain frequency dependent complex shear moduli of the gel. We further carry out force spectroscopy on these computer generated gels and study the relaxation properties as a function of the important parameters of the model, e.g., densities and relative ratios of the DNAs and the linkers, the average life time of a link, etc. Our studies are relevant for designing synthetic bio-materials for both materials and medical applications.

  16. Polish Terms for "Blue" in the Perspective of Vantage Theory

    ERIC Educational Resources Information Center

    Stanulewicz, Danuta

    2010-01-01

    The Polish set of terms for blue includes, inter alia, the following adjectives: "niebieski" "blue", "blekitny" "(sky) blue", "granatowy" "navy blue", "lazurowy" "azure", "modry" "(intense) blue" and "siny" "(grey) violet-blue". The adjective "niebieski" is the basic term; however, it shares some of its functions with "blekitny", which is…

  17. Adsorption of Methylene Blue, Bromophenol Blue, and Coomassie Brilliant Blue by α-chitin nanoparticles.

    PubMed

    Dhananasekaran, Solairaj; Palanivel, Rameshthangam; Pappu, Srinivasan

    2016-01-01

    Expelling of dyestuff into water resource system causes major thread to the environment. Adsorption is the cost effective and potential method to remove the dyes from the effluents. Therefore, an attempt was made to study the adsorption of dyestuff (Methylene Blue (MB), Bromophenol Blue (BPB) and Coomassie Brilliant Blue (CBB)) by α-chitin nanoparticles (CNP) prepared from Penaeus monodon (Fabricius, 1798) shell waste. On contrary to the most recognizable adsorption studies using chitin, this is the first study using unique nanoparticles of ⩽50 nm used for the dye adsorption process. The results showed that the adsorption process increased with increase in the concentration of CNP, contact time and temperature with the dyestuff, whereas the adsorption process decreased with increase in the initial dye concentration and strong acidic pH. The results from Fourier transform infrared (FTIR) spectroscopy confirmed that the interaction between dyestuff and CNP involved physical adsorption. The adsorption process obeys Langmuir isotherm (R (2) values were 0.992, 0.999 and 0.992 for MB, BPB and CBB, and RL value lies between 0 and 1 for all the three dyes) and pseudo second order kinetics (R (2) values were 0.996, 0.999 and 0.996 for MB, BPB and CBB) more effectively. The isotherm and kinetic models confirmed that CNP can be used as a suitable adsorbent material for the removal of dyestuff from effluents. PMID:26843977

  18. Adsorption of Methylene Blue, Bromophenol Blue, and Coomassie Brilliant Blue by α-chitin nanoparticles

    PubMed Central

    Dhananasekaran, Solairaj; Palanivel, Rameshthangam; Pappu, Srinivasan

    2015-01-01

    Expelling of dyestuff into water resource system causes major thread to the environment. Adsorption is the cost effective and potential method to remove the dyes from the effluents. Therefore, an attempt was made to study the adsorption of dyestuff (Methylene Blue (MB), Bromophenol Blue (BPB) and Coomassie Brilliant Blue (CBB)) by α-chitin nanoparticles (CNP) prepared from Penaeus monodon (Fabricius, 1798) shell waste. On contrary to the most recognizable adsorption studies using chitin, this is the first study using unique nanoparticles of ⩽50 nm used for the dye adsorption process. The results showed that the adsorption process increased with increase in the concentration of CNP, contact time and temperature with the dyestuff, whereas the adsorption process decreased with increase in the initial dye concentration and strong acidic pH. The results from Fourier transform infrared (FTIR) spectroscopy confirmed that the interaction between dyestuff and CNP involved physical adsorption. The adsorption process obeys Langmuir isotherm (R2 values were 0.992, 0.999 and 0.992 for MB, BPB and CBB, and RL value lies between 0 and 1 for all the three dyes) and pseudo second order kinetics (R2 values were 0.996, 0.999 and 0.996 for MB, BPB and CBB) more effectively. The isotherm and kinetic models confirmed that CNP can be used as a suitable adsorbent material for the removal of dyestuff from effluents. PMID:26843977

  19. TOPICAL REVIEW: Polymer gel dosimetry

    NASA Astrophysics Data System (ADS)

    Baldock, C.; De Deene, Y.; Doran, S.; Ibbott, G.; Jirasek, A.; Lepage, M.; McAuley, K. B.; Oldham, M.; Schreiner, L. J.

    2010-03-01

    Polymer gel dosimeters are fabricated from radiation sensitive chemicals which, upon irradiation, polymerize as a function of the absorbed radiation dose. These gel dosimeters, with the capacity to uniquely record the radiation dose distribution in three-dimensions (3D), have specific advantages when compared to one-dimensional dosimeters, such as ion chambers, and two-dimensional dosimeters, such as film. These advantages are particularly significant in dosimetry situations where steep dose gradients exist such as in intensity-modulated radiation therapy (IMRT) and stereotactic radiosurgery. Polymer gel dosimeters also have specific advantages for brachytherapy dosimetry. Potential dosimetry applications include those for low-energy x-rays, high-linear energy transfer (LET) and proton therapy, radionuclide and boron capture neutron therapy dosimetries. These 3D dosimeters are radiologically soft-tissue equivalent with properties that may be modified depending on the application. The 3D radiation dose distribution in polymer gel dosimeters may be imaged using magnetic resonance imaging (MRI), optical-computerized tomography (optical-CT), x-ray CT or ultrasound. The fundamental science underpinning polymer gel dosimetry is reviewed along with the various evaluation techniques. Clinical dosimetry applications of polymer gel dosimetry are also presented.

  20. Topical Review: Polymer gel dosimetry

    PubMed Central

    Baldock, C; De Deene, Y; Doran, S; Ibbott, G; Jirasek, A; Lepage, M; McAuley, K B; Oldham, M; Schreiner, L J

    2010-01-01

    Polymer gel dosimeters are fabricated from radiation sensitive chemicals which, upon irradiation, polymerize as a function of the absorbed radiation dose. These gel dosimeters, with the capacity to uniquely record the radiation dose distribution in three-dimensions (3D), have specific advantages when compared to one-dimensional dosimeters, such as ion chambers, and two-dimensional dosimeters, such as film. These advantages are particularly significant in dosimetry situations where steep dose gradients exist such as in intensity-modulated radiation therapy (IMRT) and stereotactic radiosurgery. Polymer gel dosimeters also have specific advantages for brachytherapy dosimetry. Potential dosimetry applications include those for low-energy x-rays, high-linear energy transfer (LET) and proton therapy, radionuclide and boron capture neutron therapy dosimetries. These 3D dosimeters are radiologically soft-tissue equivalent with properties that may be modified depending on the application. The 3D radiation dose distribution in polymer gel dosimeters may be imaged using magnetic resonance imaging (MRI), optical-computerized tomography (optical-CT), x-ray CT or ultrasound. The fundamental science underpinning polymer gel dosimetry is reviewed along with the various evaluation techniques. Clinical dosimetry applications of polymer gel dosimetry are also presented. PMID:20150687

  1. Alternative imaging modalities for polymer gel dosimetry

    NASA Astrophysics Data System (ADS)

    Jirasek, Andrew

    2010-11-01

    This review summarizes recent work in the area of imaging polymer gel dosimeters using x-ray CT imaging, ultrasound, and radiation-induced changes in gel mechanical properties. In addition, recent work in the area of Raman tomographic imaging of canine bone, in conjunction with past efforts in Raman imaging of polymer gel dosimeters, raises new possibilities for new polymer gel imaging techniques.

  2. Uncovering blue diffuse dwarf galaxies

    NASA Astrophysics Data System (ADS)

    James, Bethan L.; Koposov, Sergey; Stark, Daniel P.; Belokurov, Vasily; Pettini, Max; Olszewski, Edward W.

    2015-04-01

    Extremely metal poor (XMP) galaxies are known to be very rare, despite the large numbers of low-mass galaxies predicted by the local galaxy luminosity function. This paper presents a subsample of galaxies that were selected via a morphology-based search on Sloan Digital Sky Survey images with the aim of finding these elusive XMP galaxies. By using the recently discovered XMP galaxy, Leo P, as a guide, we obtained a collection of faint, blue systems, each with isolated H II regions embedded in a diffuse continuum, that have remained optically undetected until now. Here we show the first results from optical spectroscopic follow-up observations of 12 of ˜100 of these blue diffuse dwarf (BDD) galaxies yielded by our search algorithm. Oxygen abundances were obtained via the direct method for eight galaxies, and found to be in the range 7.45 < 12 + log (O/H) < 8.0, with two galaxies being classified as XMPs. All BDDs were found to currently have a young star-forming population (<10 Myr) and relatively high ionization parameters of their H II regions. Despite their low luminosities (-11 ≲ MB ≲ -18) and low surface brightnesses (˜23-25 mag arcsec-2), the galaxies were found to be actively star forming, with current star formation rates between 0.0003 and 0.078 M⊙ yr-1. From our current subsample, BDD galaxies appear to be a population of non-quiescent dwarf irregular galaxies, or the diffuse counterparts to blue compact galaxies and as such may bridge the gap between these two populations. Our search algorithm demonstrates that morphology-based searches are successful in uncovering more diffuse metal-poor star-forming galaxies, which traditional emission-line-based searches overlook.

  3. Rheological behavior of Slide Ring Gels.

    NASA Astrophysics Data System (ADS)

    Sharma, Vivek; Park, Jong Seung; Park, Jung O.; Srinivasarao, Mohan

    2006-03-01

    Slide ring gels were synthesized by chemically crosslinking, sparsely populated α-cyclodextrin (α-CD) present on the polyrotaxanes consisting of α-CD and polyethylene glycol (PEG). [1] Unlike physically or chemically crosslinked gels, slide ring gels are topological gels where crosslinks can slide along the chain. [2] We investigate the rheological behavior of these gels swollen in water and compare their viscoelastic properties to those of physical and chemical gels. We also study the equilibrium swelling behavior of these gels. [1] Okumura and Ito, Adv. Mater. 2001, 13, 485 [2] C. Zhao et al, J. Phys. Cond. Mat. 2005, 17, S2841

  4. Novel thermochromism in silica sol-gel materials

    NASA Astrophysics Data System (ADS)

    Gardener, Martin; Perry, Carole C.

    2000-05-01

    In this contribution we provide evidence for thermochromic color changes unique to silica based materials formed at low temperatures by the sol-gel process. The materials formed have potential application as temperature sensitive light filters, visual temperature indicators, self-diagnostic labels for electronic devices and IR recording media. The dopants, diamine complexes of copper(II)/nickel(II) chloride, change from purple to green following heating to 100 degrees C and revert to purple on cooling in the atmosphere. This color change has been explained by the substitution of water molecules by chloride ions in the first coordination sphere of the metal ions. When the same compounds are incorporated into a silica sol-gel matrix under acidic conditions the gel-glasses may be pale green, dark green, yellow, olive-yellow, blue or brown depending on the metal ion chosen and the extent of thermal treatment. Studies on the complexes themselves and on granular silicas doped with some of the complexes are assisting us in understanding the molecular mechanisms that give rise to these color changes.

  5. The mixing of blue stragglers

    NASA Astrophysics Data System (ADS)

    Kafka, Stella; De Propris, Roberto

    2012-08-01

    We propose to obtain high resolution spectroscopy for a sample of 17 blue stragglers in M67, in order to measure abundances of Beryllium, Carbon, Oxygen and the Carbon isotope (13C/12C) abundance ratio. The main aim of this project is to measure indications of deep mixing and therefore elucidate the processes responsible for the formation of these stars, whether stellar collisions, WUMa type mass transfer or Algol-like binary evolution. The data will also allow us to measure the importance of magnetic fields and search for faint companions via their effect on other spectral lines

  6. Thixotropic gel for vadose zone remediation

    DOEpatents

    Riha, Brian D.

    2012-07-03

    A thixotropic gel suitable for use in subsurface bioremediation is provided along with a process of using the gel. The thixotropic gel provides a non-migrating injectable substrate that can provide below ground barrier properties. In addition, the gel components provide for a favorable environment in which certain contaminants are preferentially sequestered in the gel and subsequently remediated by either indigenous or introduced microorganisms.

  7. Thixotropic gel for vadose zone remediation

    DOEpatents

    Rhia, Brian D.

    2011-03-01

    A thixotropic gel suitable for use in subsurface bioremediation is provided along with a process of using the gel. The thixotropic gel provides a non-migrating injectable substrate that can provide below ground barrier properties. In addition, the gel components provide for a favorable environment in which certain contaminants are preferentially sequestered in the gel and subsequently remediated by either indigenous or introduced microorganisms.

  8. Thixotropic gel for vadose zone remediation

    DOEpatents

    Riha, Brian D.; Looney, Brian B.

    2015-10-27

    A thixotropic gel suitable for use in subsurface bioremediation is provided along with a process of using the gel. The thixotropic gel provides a non-migrating injectable substrate that can provide below ground barrier properties. In addition, the gel components provide for a favorable environment in which certain contaminants are preferentially sequestered in the gel and subsequently remediated by either indigenous or introduced microorganisms.

  9. Gel placement in fractured systems

    SciTech Connect

    Seright, R.S.

    1995-11-01

    This paper examines several factors that can have an important effect on gel placement in fractured systems, including gelant viscosity, degree of gelation, and gravity. For an effective gel treatment, the conductivity of the fracture must be reduced and a viable flow path must remain open between the wellbore and mobile oil in the reservoir. During placement, the gelant that``leaks off`` from the fracture into the rock plays an important role in determining how well a gel treatment will reduce channeling. For a given volume of gelant injected the distance of gelant leakoff is greater for a viscous gelant than for a low-viscosity gelant. In one method to minimize gelant leakoff, sufficient gelation is designed to occur before the gelant leaves the wellbore. The authors investigated this approach in numerous experiments with both fractured and unfractured cores. They studied Cr(III)/acetate/hydrolyzed polyacrylamide (HPAM), resorcinol/formaldehyde, Cr(III)/xanthan, aluminum/citrate/HPAM, and other gelants and gels with various delay times between gelant preparation and injection. Their results suggest both hope and caution concerning the injection of gels into fractured systems.

  10. Geothermal Technologies Program Blue Ribbon Panel Recommendations

    SciTech Connect

    none,

    2011-06-17

    The Geothermal Technologies Program assembled a geothermal Blue Ribbon Panel on March 22-23, 2011 in Albuquerque, New Mexico for a guided discussion on the future of geothermal energy in the United States and the role of the DOE Program. The Geothermal Blue Ribbon Panel Report captures the discussions and recommendations of the experts. An addendum is available here: http://www.eere.energy.gov/geothermal/pdfs/gtp_blue_ribbon_panel_report_addendum10-2011.pdf

  11. The Blue Marble 43 Years Later

    Atmospheric Science Data Center

    2016-02-18

    article title:  The Blue Marble 43 Years Later View larger image Here ... points over more than four decades apart. The iconic "Blue Marble" view on the left was taken 43 years ago on December 7, 1972 from Apollo ... points over more than four decades apart. The iconic "Blue Marble" view on the left was taken 43 years ago on December 7, 1972 from Apollo ...

  12. The Blue Dots Initiative and Roadmapping Exercise

    NASA Astrophysics Data System (ADS)

    Coudé du Foresto, V.

    2010-10-01

    The Blue Dots initiative (a grassroot effort to build a scientific community in Europe around the exoplanet theme) is introduced. The Blue Dots activities include the elaboration of a roadmap towards the spectroscopic characterization of habitable exoplanets, a summary of which is presented here. While the roadmap will need to be updated regularly, it is expected that the methodology developed within Blue Dots will provide a durable framework for the elaboration of future revisions.

  13. Morphological responses of wheat to blue light

    NASA Technical Reports Server (NTRS)

    Barnes, C.; Bugbee, B.

    1992-01-01

    Blue light significantly increased tillering in wheat (Triticum aestivum L.) plants grown at the same photosynthetic photon flux (PPF). Plants were grown under two levels of blue light (400-500 nm) in a controlled environment with continuous irradiation. Plants received either 50 micromoles m-2 s-1 of blue light or 2 micromoles m-2 s-1 blue light from filtered metal halide lamps at a total irradiance of 200 micromoles m-2 s-1 PPF (400-700 nm). Plants tillered an average of 25% more under the higher level of blue light. Blue light also caused a small, but consistent, increase in main culm development, measured as Haun stage. Leaf length was reduced by higher levels of blue light, while plant dry-mass was not significantly affected by blue light. Applying the principle of equivalent light action, the results suggest that tillering and leaf elongation are mediated by the blue-UV light receptor(s) because phytochrome photoequilibrium for each treatment were nearly identical.

  14. Polymer stabilized and dispersed blue phases

    NASA Astrophysics Data System (ADS)

    Kemiklioglu, Emine

    Blue phase liquid crystal (BPLC) materials have potential for advanced applications of display material and technology based on their optical behaviors, such as field-induced birefringence and sub-millisecond response time, which is at least one order of magnitude faster than the present nematic liquid crystal based displays. Since blue phases appear in the narrow temperature range between the chiral nematic and the isotropic phases, there is a temperature range limitation for the application of blue phase liquid crystal. In this dissertation, we have developed blue phase liquid crystal materials with a wide temperature range and low driving voltage. The first goal was to develop wide-temperature range blue phase liquid crystal materials using several stabilization methods notably polymer stabilization, doping of carbon-nanotubes and bent-core molecules. The temperature range could be expanded more than 54°C via the polymer stabilization. The second goal was to explore the polymer dispersed blue phase liquid crystal combining the advantages of the polymer dispersion method and blue phase materials. Polymer encapsulated blue phase films showed a large Kerr constant, low switching voltage and fast response time. Moreover, the temperature range of encapsulated blue phase films were successfully expanded from 9°C to 54°C .

  15. Optically tuneable blue phase photonic band gaps

    SciTech Connect

    Liu, H.-Y.; Wang, C.-T.; Hsu, C.-Y.; Lin, T.-H.; Liu, J.-H.

    2010-03-22

    This study investigates an optically switchable band gap of photonic crystal that is based on an azobenzene-doped liquid crystal blue phase. The trans-cis photoisomerization of azobenzene deforms the cubic unit cell of the blue phase and shifts the photonic band gap. The fast back-isomerization of azobenzene was induced by irradiation with different wavelengths light. The crystal structure is verified using Kossel diffraction diagram. An optically addressable blue phase display, based on Bragg reflection from the photonic band gap, is also demonstrated. The tunable ranges are around red, green, and blue wavelengths and exhibit a bright saturated color.

  16. Copolymers For Capillary Gel Electrophoresis

    DOEpatents

    Liu, Changsheng; Li, Qingbo

    2005-08-09

    This invention relates to an electrophoresis separation medium having a gel matrix of at least one random, linear copolymer comprising a primary comonomer and at least one secondary comonomer, wherein the comonomers are randomly distributed along the copolymer chain. The primary comonomer is an acrylamide or an acrylamide derivative that provides the primary physical, chemical, and sieving properties of the gel matrix. The at least one secondary comonomer imparts an inherent physical, chemical, or sieving property to the copolymer chain. The primary and secondary comonomers are present in a ratio sufficient to induce desired properties that optimize electrophoresis performance. The invention also relates to a method of separating a mixture of biological molecules using this gel matrix, a method of preparing the novel electrophoresis separation medium, and a capillary tube filled with the electrophoresis separation medium.

  17. Fundamentals of Polymer Gel Dosimeters

    NASA Astrophysics Data System (ADS)

    McAuley, Kim B.

    2006-12-01

    The recent literature on polymer gel dosimetry contains application papers and basic experimental studies involving polymethacrylic-acid-based and polyacrylamide-based gel dosimeters. The basic studies assess the relative merits of these two most commonly used dosimeters, and explore the effects of tetrakis hydroxymethyl phosphonium chloride (THPC) antioxidant on dosimeter performance. Polymer gel dosimeters that contain THPC or other oxygen scavengers are called normoxic dosimeters, because they can be prepared under normal atmospheric conditions, rather than in a glove box that excludes oxygen. In this review, an effort is made to explain some of the underlying chemical phenomena that affect dosimeter performance using THPC, and that lead to differences in behaviour between dosimeters made using the two types of monomer systems. Progress on the development of new more effective and less toxic dosimeters is also reported.

  18. Sol-gel derived sorbents

    DOEpatents

    Sigman, Michael E.; Dindal, Amy B.

    2003-11-11

    Described is a method for producing copolymerized sol-gel derived sorbent particles for the production of copolymerized sol-gel derived sorbent material. The method for producing copolymerized sol-gel derived sorbent particles comprises adding a basic solution to an aqueous metal alkoxide mixture for a pH.ltoreq.8 to hydrolyze the metal alkoxides. Then, allowing the mixture to react at room temperature for a precalculated period of time for the mixture to undergo an increased in viscosity to obtain a desired pore size and surface area. The copolymerized mixture is then added to an immiscible, nonpolar solvent that has been heated to a sufficient temperature wherein the copolymerized mixture forms a solid upon the addition. The solid is recovered from the mixture, and is ready for use in an active sampling trap or activated for use in a passive sampling trap.

  19. Western blotting using in-gel protein labeling as a normalization control: stain-free technology.

    PubMed

    Gilda, Jennifer E; Gomes, Aldrin V

    2015-01-01

    Western blotting is a commonly used laboratory technique for semi-quantifying protein amounts. It is important when quantifying protein expression to account for differences in the amount of total protein loaded onto the gel using a loading control. Common loading controls include housekeeping proteins, such as β-actin or GAPDH, quantified by Western blot, or total protein, quantified using a stain such as Coomassie Brilliant Blue or Ponceau S. A more recently developed method for total protein quantification utilizes stain-free technology, which has a linear dynamic detection range and allows for protein detection on both gels and membranes. Here, we describe the theory and use of stain-free gels for total protein quantification and normalization of Western blots. PMID:25820735

  20. Statistical physics of polymer gels

    NASA Astrophysics Data System (ADS)

    Panyukov, Sergei; Rabin, Yitzhak

    1996-05-01

    This work presents a comprehensive analysis of the statistical mechanics of randomly cross-linked polymer gels, starting from a microscopic model of a network made of instantaneously cross-linked Gaussian chains with excluded volume, and ending with the derivation of explicit expressions for the thermodynamic functions and for the density correlation functions which can be tested by experiments. Using replica field theory we calculate the mean field density in replica space and show that this solution contains statistical information about the behavior of individual chains in the network. The average monomer positions change affinely with macroscopic deformation and fluctuations about these positions are limited to length scales of the order of the mesh size. We prove that a given gel has a unique state of microscopic equilibrium which depends on the temperature, the solvent, the average monomer density and the imposed deformation. This state is characterized by the set of the average positions of all the monomers or, equivalently, by a unique inhomogeneous monomer density profile. Gels are thus the only known example of equilibrium solids with no long-range order. We calculate the RPA density correlation functions that describe the statistical properties of small deviations from the average density, due to both static spatial heterogeneities (which characterize the inhomogeneous equilibrium state) and thermal fluctuations (about this equilibrium). We explain how the deformation-induced anisotropy of the inhomogeneous equilibrium density profile is revealed by small angle neutron scattering and light scattering experiments, through the observation of the butterfly effect. We show that all the statistical information about the structure of polymer networks is contained in two parameters whose values are determined by the conditions of synthesis: the density of cross-links and the heterogeneity parameter. We find that the structure of instantaneously cross

  1. Calcium Alginate Gels as Stem Cell Matrix – Making Paracrine Stem Cell Activity Available for Enhanced Healing after Surgery

    PubMed Central

    Schmitt, Andreas; Rödel, Philipp; Anamur, Cihad; Seeliger, Claudine; Imhoff, Andreas B.; Herbst, Elmar; Vogt, Stephan; van Griensven, Martijn; Winter, Gerhard; Engert, Julia

    2015-01-01

    Regeneration after surgery can be improved by the administration of anabolic growth factors. However, to locally maintain these factors at the site of regeneration is problematic. The aim of this study was to develop a matrix system containing human mesenchymal stem cells (MSCs) which can be applied to the surgical site and allows the secretion of endogenous healing factors from the cells. Calcium alginate gels were prepared by a combination of internal and external gelation. The gelling behaviour, mechanical stability, surface adhesive properties and injectability of the gels were investigated. The permeability of the gels for growth factors was analysed using bovine serum albumin and lysozyme as model proteins. Human MSCs were isolated, cultivated and seeded into the alginate gels. Cell viability was determined by AlamarBlue assay and fluorescence microscopy. The release of human VEGF and bFGF from the cells was determined using an enzyme-linked immunoassay. Gels with sufficient mechanical properties were prepared which remained injectable through a syringe and solidified in a sufficient time frame after application. Surface adhesion was improved by the addition of polyethylene glycol 300,000 and hyaluronic acid. Humans MSCs remained viable for the duration of 6 weeks within the gels. Human VEGF and bFGF was found in quantifiable concentrations in cell culture supernatants of gels loaded with MSCs and incubated for a period of 6 weeks. This work shows that calcium alginate gels can function as immobilization matrices for human MSCs. PMID:25793885

  2. 5'-S-(2-aminoethyl)-N6-(4-nitrobenzyl)-5'-thioadenosine (SAENTA), a novel ligand with high affinity for polypeptides associated with nucleoside transport. Partial purification of the nitrobenzylthioinosine-binding protein of pig erythrocytes by affinity chromatography.

    PubMed Central

    Agbanyo, F R; Vijayalakshmi, D; Craik, J D; Gati, W P; McAdam, D P; Asakura, J; Robins, M J; Paterson, A R; Cass, C E

    1990-01-01

    Derivatives of N6-(4-aminobenzyl)adenosine (substituted at the aminobenzyl group) and 5'-linked derivatives of N6-(4-nitrobenzyl)adenosine (NBAdo) were evaluated as inhibitors of site-specific binding of [3H]nitrobenzylthioinosine (NBMPR) to pig erythrocyte membranes. Potent inhibitors were SAENTA [5'-S-(2-aminoethyl)-N6-(4-nitrobenzyl)-5'-thioadenosine] and acetyl-SAENTA (the 2-acetamidoethyl derivative of SAENTA). SAENTA was coupled to derivatized agarose-gel beads (Affi-Gel 10) to form an affinity matrix for chromatographic purification of NBMPR-binding polypeptides, which in pig erythrocytes are part of, or are associated with, the equilibrative nucleoside transporter. When pig erythrocyte membranes were solubilized with octyl glucoside (n-octyl beta-D-glucopyranoside) and applied to SAENTA-Affi-Gel 10 (SAENTA-AG10), polypeptides that migrated as a broad band on SDS/PAGE with an apparent molecular mass of 58-60 kDa were selectively retained by the affinity gel. These polypeptides were identified as components of the nucleoside transporter of pig erythrocytes by reactivity with a monoclonal antibody (mAb 11C4) that recognizes the NBMPR-binding protein of pig erythrocytes. Retention of the immunoreactive polypeptides by SAENTA-AG10 was blocked by NBAdo. The immunoreactive polypeptides were released from SAENTA-AG10 by elution under denaturing conditions with 1% SDS or by elution with detergent solutions containing competitive ligands (NBAdo or NBMPR). A 72-fold enrichment of the immunoreactive polypeptides was achieved by a single passage of solubilized, protein-depleted membranes through a column of SAENTA-AG10, followed by elution with detergent solutions containing NBAdo. These results demonstrate that polypeptide components of NBMPR-sensitive nucleoside-transport systems may be partly purified by affinity chromatography using gel media bearing SAENTA groups. Images Fig. 5. Fig. 6. Fig. 7. PMID:2241896

  3. Long-persistence blue phosphors

    NASA Technical Reports Server (NTRS)

    Yen, William M. (Inventor); Jia, Weiyi (Inventor); Lu, Lizhu (Inventor); Yuan, Huabiao (Inventor)

    2000-01-01

    This invention relates to phosphors including long-persistence blue phosphors. Phosphors of the invention are represented by the general formula: MO . mAl.sub.2 O.sub.3 :Eu.sup.2+,R.sup.3+ wherein m is a number ranging from about 1.6 to about 2.2, M is Sr or a combination of Sr with Ca and Ba or both, R.sup.3+ is a trivalent metal ion or trivalent Bi or a mixture of these trivalent ions, Eu.sup.2+ is present at a level up to about 5 mol % of M, and R.sup.3+ is present at a level up to about 5 mol % of M. Phosphors of this invention include powders, ceramics, single crystals and single crystal fibers. A method of manufacturing improved phosphors and a method of manufacturing single crystal phosphors are also provided.

  4. Staining of proteins in gels with Coomassie G-250 without organic solvent and acetic acid.

    PubMed

    Lawrence, Ann-Marie; Besir, H Uuml Seyin

    2009-01-01

    In classical protein staining protocols using Coomassie Brilliant Blue (CBB), solutions with high contents of toxic and flammable organic solvents (Methanol, Ethanol or 2-Propanol) and acetic acid are used for fixation, staining and destaining of proteins in a gel after SDS-PAGE. To speed up the procedure, heating the staining solution in the microwave oven for a short time is frequently used. This usually results in evaporation of toxic or hazardous Methanol, Ethanol or 2-Propanol and a strong smell of acetic acid in the lab which should be avoided due to safety considerations. In a protocol originally published in two patent applications by E.M. Wondrak (US2001046709 (A1), US6319720 (B1)), an alternative composition of the staining solution is described in which no organic solvent or acid is used. The CBB is dissolved in bidistilled water (60-80 mg of CBB G-250 per liter) and 35 mM HCl is added as the only other compound in the staining solution. The CBB staining of the gel is done after SDS-PAGE and thorough washing of the gel in bidistilled water. By heating the gel during the washing and staining steps, the process can be finished faster and no toxic or hazardous compounds are evaporating. The staining of proteins occurs already within 1 minute after heating the gel in staining solution and is fully developed after 15-30 min with a slightly blue background that is destained completely by prolonged washing of the stained gel in bidistilled water, without affecting the stained protein bands. PMID:19684570

  5. Blue enhanced light sources: opportunities and risks

    NASA Astrophysics Data System (ADS)

    Lang, Dieter

    2012-03-01

    Natural daylight is characterized by high proportions of blue light. By proof of a third type of photoreceptor in the human eye which is only sensitive in this spectral region and by subsequent studies it has become obvious that these blue proportions are essential for human health and well being. In various studies beneficial effects of indoor lighting with higher blue spectral proportions have been proven. On the other hand with increasing use of light sources having enhanced blue light for indoor illumination questions are arising about potential health risks attributed to blue light. Especially LED are showing distinct emission characteristics in the blue. Recently the French agency for food, environmental and occupational health & safety ANSES have raised the question on health issues related to LED light sources and have claimed to avoid use of LED for lighting in schools. In this paper parameters which are relevant for potential health risks will be shown and their contribution to risk factors will quantitatively be discussed. It will be shown how to differentiate between photometric parameters for assessment of beneficial as well as hazardous effects. Guidelines will be discussed how blue enhanced light sources can be used in applications to optimally support human health and well being and simultaneously avoid any risks attributed to blue light by a proper design of lighting parameters. In the conclusion it will be shown that no inherent health risks are related to LED lighting with a proper lighting design.

  6. Blue Skies, Coffee Creamer, and Rayleigh Scattering

    ERIC Educational Resources Information Center

    Liebl, Michael

    2010-01-01

    The first physical explanation of Earths blue sky was fashioned in 1871 by Lord Rayleigh. Many discussions of Rayleigh scattering and approaches to studying it both in and out of the classroom are available. Rayleigh scattering accounts for the blue color of the sky and the orange/red color of the Sun near sunset and sunrise, and a number of…

  7. Blue collection bag after ileal diversion.

    PubMed

    Hildreth, T A; Cass, A S

    1978-02-01

    Five children with ileal diversions have shown asymptomatic blue staining of the urine collection bags. A tryptophan derivative (indican) in the urine that oxidizes to indigo blue on exposure to air is thought to be the cause of this benign transient phenomenon. PMID:628994

  8. Delta Blues Scholarship and Imperialist Nostalgia.

    ERIC Educational Resources Information Center

    Nye, William P.

    When Delta blues are considered to be "folk music," the genre is inextricably tied to the neocolonial, sharecropping system of cotton production characteristic of the Mississippi Delta region between the Civil War and World War II. "Imperialist nostalgia," then, arises in accounts which pay primary and positive tribute to blues performances…

  9. Nonlinear elasticity of alginate gels

    NASA Astrophysics Data System (ADS)

    Hashemnejad, Seyed Meysam; Kundu, Santanu

    Alginate is a naturally occurring anionic polysaccharide extracted from brown algae. Because of biocompatibility, low toxicity, and simple gelation process, alginate gels are used in biomedical and food applications. Here, we report the rheological behavior of ionically crosslinked alginate gels, which are obtained by in situ gelation of alginates with calcium salts, in between two parallel plates of a rheometer. Strain stiffening behavior was captured using large amplitude oscillatory shear (LAOS) experiments. In addition, negative normal stress was observed for these gels, which has not been reported earlier for any polysaccharide networks. The magnitude of negative normal stress increases with applied strain and can exceed that of the shear stress at large strain. Rheological results fitted with a constitutive model that considers both stretching and bending of chains indicate that nonlinearity is likely related to the stretching of the chains between the crosslink junctions. The results provide an improved understanding of the deformation mechanism of ionically crosslinked alginate gel and the results will be important in developing synthetic extracellular matrix (ECM) from these materials.

  10. Purification and Characterization of Liposan, a Bioemulsifier from Candida lipolytica†

    PubMed Central

    Cirigliano, Michael C.; Carman, George M.

    1985-01-01

    The inducible water-soluble bioemulsifier liposan (M. C. Cirigliano and G. M. Carman, Appl. Environ. Microbiol. 48:747-750, 1984) was purified from the yeast Candida lipolytica. The purification procedure included repeated solvent extractions of a concentrated culture filtrate and Affi-Gel concanavalin A affinity chromatography. The procedure yielded a preparation containing a major band (Mr = 27,600) which stained for protein and carbohydrate upon polyacrylamide gel electrophoresis in the presence of sodium dodecyl sulfate. Liposan is composed of approximately 83% carbohydrate and 17% protein. Acid and enzymatic digestions of the emulsifier revealed that the carbohydrate portion is a heteropolysaccharide consisting of glucose, galactose, galactosamine, and galacturonic acid. Liposan effected and stabilized oil-in-water emulsions with a variety of commercial vegetable oils. Emulsification and stabilization properties of liposan were compared to those of a number of commercial emulsifiers and stabilizers. Images PMID:16346917

  11. Featured Molecules: Ascorbic Acid and Methylene Blue

    NASA Astrophysics Data System (ADS)

    Coleman, William F.; Wildman, Randall J.

    2003-05-01

    The WebWare molecules of the month for May are featured in several articles in this issue. "Arsenic: Not So Evil After All?" discusses the pharmaceutical uses of methylene blue and its development as the first synthetic drug used against a specific disease. The JCE Classroom Activity "Out of the Blue" and the article "Greening the Blue Bottle" feature methylene blue and ascorbic acid as two key ingredients in the formulation of the blue bottle. You can also see a colorful example of these two molecules in action on the cover. "Sailing on the 'C': A Vitamin Titration with a Twist" describes an experiment to determine the vitamin C (ascorbic acid) content of citrus fruits and challenges students, as eighteenth-century sea captains, to decide the best fruit to take on a long voyage. Fully manipulable (Chime) versions of these and other molecules are available at Only@JCE Online.

  12. Elementary theorems regarding blue isocurvature perturbations

    NASA Astrophysics Data System (ADS)

    Chung, Daniel J. H.; Yoo, Hojin

    2015-04-01

    Blue CDM-photon isocurvature perturbations are attractive in terms of observability and may be typical from the perspective of generic mass relations in supergravity. We present and apply three theorems useful for blue isocurvature perturbations arising from linear spectator scalar fields. In the process, we give a more precise formula for the blue spectrum associated with the axion model of Kasuya and Kawasaki [Axion Isocurvature Fluctuations with Extremely Blue Spectrum, Phys. Rev. D 80, 023516 (2009).], which can in a parametric corner give a factor of O (10 ) correction. We explain how a conserved current associated with Peccei-Quinn symmetry plays a crucial role and explicitly plot several example spectra including the breaks in the spectra. We also resolve a little puzzle arising from a naive multiplication of isocurvature expression that sheds light on the gravitational imprint of the adiabatic perturbations on the fields responsible for blue isocurvature fluctuations.

  13. Inactivation of yeast hexokinase by Cibacron Blue 3G-A: spectral, kinetic and structural investigations.

    PubMed Central

    Puri, R N; Roskoski, R

    1994-01-01

    Yeast hexokinase, a homodimer (100 kDa), is an important enzyme in the glycolytic pathway. Although Cibacron Blue 3G-A (Reactive Blue 2) has been previously shown to inactivate yeast hexokinase, no comprehensive study exists concerning the nature of interaction(s) between hexokinase and the blue dye. A comparison of the computer-generated three-dimensional (3D) representations showed considerable overlap of the purine ring of ATP, a nucleotide substrate of hexokinase, with the hydrophobic anthraquinone moiety of the blue dye. The visible spectrum of the blue dye showed a characteristic absorption band centred at 628 nm. The visible difference spectrum of increasing concentration of the dye and the same concentrations of the dye plus a fixed concentration of hexokinase exhibited a maximum, a minimum and an isobestic point at 683, 585, and 655 nm respectively. The visible difference spectrum of the blue dye and the dye in 50% ethylene glycol showed a maximum and a minimum at 660 and 570 nm respectively. The visible difference spectrum of the blue dye in the presence of the dye and hexokinase modified at the active site by pyridoxal phosphate, iodoacetamide and o-phthalaldehyde was devoid of bands characteristic of the hexokinase-blue dye complex. Size-exclusion-chromatographic studies in the absence or presence of guanidinium chloride showed that the enzyme inactivated by the blue dye was co-eluted with the unmodified enzyme. The dialysis residue obtained after extensive dialysis of the gel-filtered complex, against a buffer of high ionic strength, showed an absorption maximum at 655 nm characteristic of the dye-enzyme complex. Inactivation data when analysed by 'Kitz-Wilson'-type kinetics for an irreversible inhibitor, yielded values of 0.05 min-1 and 92 microM for maximum rate of inactivation (k3) and dissociation constant (Kd) for the enzyme-dye complex respectively. Sugar and nucleotide substrates protected hexokinase against inactivation by the blue dye. About 2

  14. Calculating Percent Gel For Process Control

    NASA Technical Reports Server (NTRS)

    Webster, Charles Neal; Scott, Robert O.

    1988-01-01

    Reaction state of thermosetting resin tracked to assure desired properties. Rate of gel determined as function of temperature by measuring time to gel of part of graphite fabric impregnated with Hexcel R120 (or equivalent) phenolic resin.

  15. 3D Gel Map of Arabidopsis Complex I

    PubMed Central

    Peters, Katrin; Belt, Katharina; Braun, Hans-Peter

    2013-01-01

    Complex I has a unique structure in plants and includes extra subunits. Here, we present a novel study to define its protein constituents. Mitochondria were isolated from Arabidopsis thaliana cell cultures, leaves, and roots. Subunits of complex I were resolved by 3D blue-native (BN)/SDS/SDS-PAGE and identified by mass spectrometry. Overall, 55 distinct proteins were found, seven of which occur in pairs of isoforms. We present evidence that Arabidopsis complex I consists of 49 distinct types of subunits, 40 of which represent homologs of bovine complex I. The nine other subunits represent special proteins absent in the animal linage of eukaryotes, most prominently a group of subunits related to bacterial gamma-type carbonic anhydrases. A GelMap http://www.gelmap.de/arabidopsis-3d-complex-i/ is presented for promoting future complex I research in Arabidopsis thaliana. PMID:23761796

  16. Photoluminescence of titanium-doped zinc spinel blue-emitting nanophosphors

    SciTech Connect

    Tsai, Mu-Tsun; Chang, Yee-Shin; Chou, You-Hsin; Tsai, Kai-Min

    2014-06-01

    A blue-emitting phosphor of titanium-doped zinc spinel (ZnAl{sub 2}O{sub 4}:Ti; Ti=0–6.0 mol% in relation to Al) nanopowders was prepared by a simple sol–gel method. On annealing at 1000 °C, single-phase ZnAl{sub 2}O{sub 4}:Ti powders had primary particles of 25–30 nm in size and most Ti ions in the form of Ti{sup 4+}. Under UV excitation at 280 nm, a strong and broad blue emission centered at 435 nm was observed. The sources of the excitation and emission were assigned to the charge-transfer excitation and recombination between O{sup 2–}–Ti{sup 4+} and Ti{sup 3+}–O{sup –} ion pairs. Optimum brightness occurred at a doping of 2.0 mol% Ti. The decay lifetime of ZnAl{sub 2}O{sub 4}:2%Ti was calculated to be 3.0 ms for the blue emission with CIE coordinates of x=0.168 and y=0.153. The results suggest that ZnAl{sub 2}O{sub 4}:Ti is a promising candidate for application as a blue component phosphor for UV-converting white light-emitting diodes. - Graphical abstract: The absorption band around 270 nm is associated with the charge-transfer processes between octahedral Ti{sup 4+} and O{sup 2−} ions. The excitation band around 280 nm corresponds to the charge-transfer excitations from O{sup 2–}(2p){sup 6} electrons to Ti{sup 4+} (3d{sup 0}). Under 280 nm excitation, the PL spectrum shows a strong blue emission with a peak at around 435 nm. - Highlights: • Single-phase ZnAl{sub 2}O{sub 4}:Ti nanocrystals have been synthesized by a sol–gel process. • Under UV excitation at 280 nm, the blue emission centered at 435 nm is observed. • Blue emission is attributed to a charge-transfer transition involving the Ti{sup 4+} ions.

  17. Strain Diversity of Pseudomonas fluorescens Group with Potential Blue Pigment Phenotype Isolated from Dairy Products.

    PubMed

    Chierici, Margherita; Picozzi, Claudia; La Spina, Marisa Grazia; Orsi, Carla; Vigentini, Ileana; Zambrini, Vittorio; Foschino, Roberto

    2016-08-01

    The blue discoloration in Mozzarella cheese comes from bacterial spoilage due to contamination with Pseudomonas. Fourteen Pseudomonas fluorescens strains from international collections and 55 new isolates of dominant bacterial populations from spoiled fresh cheese samples were examined to assess genotypic and phenotypic strain diversity. Isolates were identified by 16S rRNA gene sequencing and tested for the production of the blue pigment at various temperatures on Mascarpone agar and in Mozzarella preserving fluid (the salty water in which the cheese is conserved, which becomes enriched by cheese minerals and peptides during storage). Pulsed-field gel electrophoresis analysis after treatment with the endonuclease SpeI separated the isolates into 42 genotypes at a similarity level of 80%. Based on the pulsotype clustering, 12 representative strains producing the blue discoloration were chosen for the multilocus sequence typing targeting the gyrB, glnS, ileS, nuoD, recA, rpoB, and rpoD genes. Four new sequence typing profiles were discovered, and the concatenated sequences of the investigated loci grouped the tested strains into the so-called ''blue branch'' of the P. fluorescens phylogenetic tree, confirming the linkage between pigment production and a specific genomic cluster. Growth temperature affected pigment production; the blue discoloration appeared at 4 and 14°C but not at 30°C. Similarly, the carbon source influenced the phenomenon; the blue phenotype was generated in the presence of glucose but not in the presence of galactose, sodium succinate, sodium citrate, or sodium lactate. PMID:27497132

  18. Synthesis of mesoporous TiO2-curcumin nanoparticles for photocatalytic degradation of methylene blue dye.

    PubMed

    Abou-Gamra, Z M; Ahmed, M A

    2016-07-01

    Herein, we demonstrate a facile route for synthesis a new photocatalyst based on TiO2-curcumin nanoparticles for photodegradation of methylene blue dye under UV and visible light irradiation. The photocatalyst was prepared by sol-gel method using chitosan as biodegradable polymer. The crystalline and the nanostructure were characteristic X-ray diffraction [XRD], adsorption-desorption isotherm and high resolution transmission electron microscopy [HRTEM]. However, the optical features of the samples were investigated by a UV-visible spectrophotometer. It is obvious to notice the removal of the majority of methylene blue dye on a pure titania surface via adsorption mechanism owing to the high surface area and to the organized mesoporous nature of the solid sample. Incorporation of curcumin on titania surface changes the removal direction from adsorption to the photocatalytic pathway. Various photocatalytic experiments were performed to investigate the influence of initial dye concentration, weight of catalyst, stirring and light intensity on the photocatalytic degradation of methylene blue as primary pollutant model. Chemical oxygen demand [COD] test confirms the complete degradation of methylene blue dye. The exceptional photocatalytic reactivity of titania-curcumin nanoparticles is referred to reduction in band gap energy and to the facility of electron transfer from II* curcumin energy level to titania conduction band which increases the concentration of reactive oxygen superoxide radicals which in turn prevents the electron-hole recombination. The effect of various scavengers on the methylene blue dye degradation was investigated using ethanol, ascorbic acid and methyl viologen. The results have pointed out that O2(-) and HO(.) are considered the main active species in the degradation process. A plausible pathway and mechanism for the photocatalytic degradation of methylene blue by titania-curcumin nanoparticles were illustrated. PMID:27107333

  19. Characteristics of platelet gels combined with silk

    PubMed Central

    Pallotta, Isabella; Kluge, Jonathan A.; Moreau, Jodie; Calabrese, Rossella

    2014-01-01

    Platelet gel, a fibrin network containing activated platelets, is widely used in regenerative medicine due the capacity of platelet-derived growth factors to accelerate and direct healing processes. However, limitations to this approach include poor mechanical properties, relatively rapid degradation, and the lack of control of release of growth factors at the site of injection. These issues compromise the ability of platelet gels for sustained function in regenerative medicine. In the present study, a combination of platelet gels with silk fibroin gel was studied to address the above limitations. Mixing sonicated silk gels with platelet gels extended the release of growth factors without inhibiting gel forming ability. The released growth factors were biologically active and their delivery was modified further by manipulation of the charge of the silk protein. Moreover, the silk gel augmented both the rheological properties and compressive stiffness of the platelet gel, tuned by the silk concentration and/or silk/platelet gel ratio. Silk-platelet gel injections in nude rats supported enhanced cell infiltration and blood vessel formation representing a step towards new platelet gel formulations with enhanced therapeutic impact. PMID:24480538

  20. Spring-loaded polymeric gel actuators

    DOEpatents

    Shahinpoor, M.

    1995-02-14

    Spring-loaded electrically controllable polymeric gel actuators are disclosed. The polymeric gels can be polyvinyl alcohol, polyacrylic acid, or polyacrylamide, and are contained in an electrolytic solvent bath such as water plus acetone. The action of the gel is mechanically biased, allowing the expansive and contractile forces to be optimized for specific applications. 5 figs.

  1. A clarified gel for crystal growth

    NASA Technical Reports Server (NTRS)

    Barber, P. G.; Simpson, N. R.

    1985-01-01

    A procedure for preparing clarified sodium silicate gels suitable for crystal growth is described. In the method described here, the silicate stock is clarified by pretreating it with cation exchange resins before preparing the gels. Also, a modified recipe is proposed for preparing gels to achieve improved transparency.

  2. Characteristics of platelet gels combined with silk.

    PubMed

    Pallotta, Isabella; Kluge, Jonathan A; Moreau, Jodie; Calabrese, Rossella; Kaplan, David L; Balduini, Alessandra

    2014-04-01

    Platelet gel, a fibrin network containing activated platelets, is widely used in regenerative medicine due the capacity of platelet-derived growth factors to accelerate and direct healing processes. However, limitations to this approach include poor mechanical properties, relatively rapid degradation, and the lack of control of release of growth factors at the site of injection. These issues compromise the ability of platelet gels for sustained function in regenerative medicine. In the present study, a combination of platelet gels with silk fibroin gel was studied to address the above limitations. Mixing sonicated silk gels with platelet gels extended the release of growth factors without inhibiting gel-forming ability. The released growth factors were biologically active and their delivery was modified further by manipulation of the charge of the silk protein. Moreover, the silk gel augmented both the rheological properties and compressive stiffness of the platelet gel, tuned by the silk concentration and/or silk/platelet gel ratio. Silk-platelet gel injections in nude rats supported enhanced cell infiltration and blood vessel formation representing a step towards new platelet gel formulations with enhanced therapeutic impact. PMID:24480538

  3. Spring-loaded polymeric gel actuators

    DOEpatents

    Shahinpoor, Mohsen

    1995-01-01

    Spring-loaded electrically controllable polymeric gel actuators are disclosed. The polymeric gels can be polyvinyl alcohol, polyacrylic acid, or polyacrylamide, and are contained in an electrolytic solvent bath such as water plus acetone. The action of the gel is mechanically biased, allowing the expansive and contractile forces to be optimized for specific applications.

  4. Cu-doped CdS and ZnS nanocrystals grown onto thiolated silica-gel

    NASA Astrophysics Data System (ADS)

    Andrade, George Ricardo Santana; Nascimento, Cristiane da Cunha; Xavier, Paulo Adriano; Costa, Silvanio Silverio Lopes; Costa, Luiz Pereira; Gimenez, Iara F.

    2014-11-01

    CdS and ZnS nanocrystals were grown over specific binding sites onto a thiolated silica-gel aiming to favor defect emission processes. This strategy was found to be effective in yielding ZnS nanocrystals with simultaneous blue and blue-green emissions owing to different types of defects. The effects of doping with copper ions have been observed on the photoluminescence properties. The intensity of defect-related emissions from both semiconductor nanocrystals increased with increasing dopant concentration from 0.25% to 1.5% copper, consistent with the presence of sulfur vacancies. Higher dopant concentrations lead to concentration quenching.

  5. Isolation of Salmonella typhimurium from dead blue and gold macaws (Ara ararauna).

    PubMed

    Vigo, Germán B; Origlia, Javier; Gornatti, Daniel; Piscopo, Miguel; Salve, Angela; Caffer, María I; Pichel, Mariana; Binsztein, Norma; Leotta, Gerardo A

    2009-03-01

    Two blue and gold macaw (Ara ararauna) chicks died of fatal salmonellosis in Buenos Aires Province, Argentina. The birds were histopathologically and microbiologically examined. Salmonella enterica subspecies enterica serovar Typhimurium was isolated from the liver, spleen, heart, lung, kidney, and intestine of both birds. All strains were susceptible to ampicillin, cephalothin, cefotaxime, enrofloxacin, nalidixic acid, gentamicin, streptomycin, chloramphenicol, fosfomycin, tetracycline, nitrofurantoin, and trimethoprim-sulfamethoxazole. The XbaI-PFGE profile of the Salmonella Typhimurium isolated from the two animals, which shared the same cage, was identical and showed a unique pattern compared with 301 isolates included in the PulseNet national database of Salmonella pulsed-field gel electrophoresis patterns. This is the first report that describes fatal cases of salmonellosis from blue and gold macaws. PMID:19432017

  6. Gel-based coloration technique for the submillimeter-scale imaging of labile phosphorus in sediments and soils with diffusive gradients in thin films.

    PubMed

    Ding, Shiming; Wang, Yan; Xu, Di; Zhu, Chungang; Zhang, Chaosheng

    2013-07-16

    We report a highly promising technique for the high-resolution imaging of labile phosphorus (P) in sediments and soils in combination with the diffusive gradients in thin films (DGT). This technique was based on the surface coloration of the Zr-oxide binding gel using the conventional molybdenum blue method following the DGT uptake of P to this gel. The accumulated mass of the P in the gel was then measured according to the grayscale intensity on the gel surface using computer-imaging densitometry. A pretreatment of the gel in hot water (85 °C) for 5 d was required to immobilize the phosphate and the formed blue complex in the gel during the color development. The optimal time required for a complete color development was determined to be 45 min. The appropriate volume of the coloring reagent added was 200 times of that of the gel. A calibration equation was established under the optimized conditions, based on which a quantitative measurement of P was obtained when the concentration of P in solutions ranged from 0.04 mg L(-1) to 4.1 mg L(-1) for a 24 h deployment of typical DGT devices at 25 °C. The suitability of the coloration technique was well demonstrated by the observation of small, discrete spots with elevated P concentrations in a sediment profile. PMID:23763454

  7. Cool Stars Sing the Blues

    NASA Astrophysics Data System (ADS)

    Luttermoser, D. G.

    2005-12-01

    A high-dispersion spectral atlas of cool red giant stars in the blue and violet is presented. The spectra were obtained over a six-year time period with the stellar spectrograph of the McMath-Pierce Telescope on Kitt Peak. Both N-type carbon stars and M-type oxygen-rich stars are presented from 3900 to 4600 Å, with the M-type stars containing both semiregular and Mira-type variables. The dominant absorption features in these stars at these wavelength result primarily from neutral metals, especially iron, and the CH and CN diatomic molecules. The Miras also show strong emission lines during some of their pulsation cycle. Many of these emission lines result from fluorescence from the Mg II h & k lines in the UV. For these fluoresced features, comparisons are made between the Miras and the semiregular carbon-rich and oxygen-rich variables. Where the oxygen-rich semiregulars show no hint of fluorescence in these features, the carbon stars show a definite ``filling-in'' of the absorption lines.

  8. Semiconducting layered blue phosphorus: a computational study.

    PubMed

    Zhu, Zhen; Tománek, David

    2014-05-01

    We investigate a previously unknown phase of phosphorus that shares its layered structure and high stability with the black phosphorus allotrope. We find the in-plane hexagonal structure and bulk layer stacking of this structure, which we call "blue phosphorus," to be related to graphite. Unlike graphite and black phosphorus, blue phosphorus displays a wide fundamental band gap. Still, it should exfoliate easily to form quasi-two-dimensional structures suitable for electronic applications. We study a likely transformation pathway from black to blue phosphorus and discuss possible ways to synthesize the new structure. PMID:24836265

  9. Retinal Effects Of Blue Light Exposure

    NASA Astrophysics Data System (ADS)

    Ham, William T.; Mueller, Harold A.; Ruffolo, J. J.

    1980-10-01

    Recent research has shown that blue light exposure is an important factor in certain types of retinal injury. The mammalian ocular media transmits the spectral band 400-1400 nm to the retina. The short wavelengths (400-550 nm) produce a photochemical or actinic type of damage, while the longer wavelengths (550-1400 nm) produce thermal damage. Distinction between the two types of retinal damage are discussed briefly and the importance of the blue light effect for solar retinitis and eclipse blindness is emphasized. The significance of blue light retinal injury is summarized for various environmental and occupational exposures.

  10. Blue jays nest in an unusual structure

    USGS Publications Warehouse

    Muths, Erin L.; Lyons, Curtis P.; Sedgwick, James A.

    2007-01-01

    We describe a successful Blue Jay (Cyanocitta cristata) nest in an unusual structure on the side of a building.  The nest was located near the edge of the species' range along the Front Range of the Rocky Mountains in Colorado.  The nest was completely obvious, suggesting that the structure itself provided adequate cover and sercurity for the jays.  Blue Jays appear to be declining in some areas of the United States such as the Southeast.  Structures such as the one we describe may be more useful in attracting Blue Jays than the nesting platforms available commercially.

  11. Blue outliers among intermediate redshift quasars

    NASA Astrophysics Data System (ADS)

    Marziani, P.; Sulentic, J. W.; Stirpe, G. M.; Dultzin, D.; Del Olmo, A.; Martínez-Carballo, M. A.

    2016-01-01

    [OIII]λ 5007 "blue outliers"—that are suggestive of outflows in the narrow line region of quasars—appear to be much more common at intermediate z (high luminosity) than at low z. About 40~% of quasars in a Hamburg ESO intermediate z sample of 52 sources qualify as "blue outliers" (i.e., quasars with [OIII]λλ 4959,5007 lines showing large systematic blueshifts with respect to rest frame). We discuss major findings on what has become an intriguing field in active galactic nuclei research and stress the relevance of "blue outliers" to feedback and host galaxy evolution.

  12. The Swelling of Olympic Gels

    NASA Astrophysics Data System (ADS)

    Lang, Michael; Fischer, Jakob; Werner, Marco; Sommer, Jens-Uwe

    2014-03-01

    The swelling equilibrium of Olympic gels is studied by Monte Carlo Simulations. We observe that gels consisting of flexible cyclic molecules of a higher degree of polymerization N show a smaller equilibrium swelling degree Q ~N - 0 . 28φ0- 0 . 72 for the same monomer volume fraction φ0 at network preparation. This observation is explained by a disinterpenetration process of overlapping non-concatenated polymers upon swelling. In the limit of a sufficiently large number of concatenations per cyclic molecule we expect that the equilibrium degree of swelling becomes proportional to φ0- 1 / 2 independent of N. Our results challenge current textbook models for the equilibrium degree of swelling of entangled polymer networks. Now at: Bio Systems Analysis Group, Jena Centre for Bioinformatics (JCB) and Department for Mathematics and Computer Sciences, Friedrich Schiller University of Jena, 07743 Jena, Germany.

  13. Supercoiling transformation of chemical gels.

    PubMed

    Asai, Makoto; Katashima, Takuya; Sakai, Takamasa; Shibayama, Mitsuhiro

    2015-09-28

    The swelling/deswelling behavior of chemical gels has been an unsolved problem disputed over for a long time. The Obukhov-Rubinstein-Colby model depicts the influence that swelling/deswelling has on elasticity, but its physical picture is too complicated to be sufficiently validated by experiment. In this study, we use molecular dynamics simulation to verify the validity of the molecular picture of network strands predicted by the Obukhov-Rubinstein-Colby model. We conclude that the physical picture of the Obukhov-Rubinstein-Colby model is reasonable, and furthermore the simulation can reveal the details of conformational changes in network strands during the supercoiling transformation. Our findings not only reveal the validity, but also give a better understanding of the dynamics of the swelling/deswelling behavior of chemical gels. PMID:26279149

  14. Nanocrystal/sol-gel nanocomposites

    DOEpatents

    Klimov, Victor L.; Petruska, Melissa A.

    2010-05-25

    The present invention is directed to a process for preparing a solid composite having colloidal nanocrystals dispersed within a sol-gel matrix, the process including admixing colloidal nanocrystals with an amphiphilic polymer including hydrophilic groups selected from the group consisting of --COOH, --OH, --SO.sub.3H, --NH.sub.2, and --PO.sub.3H.sub.2 within a solvent to form an alcohol-soluble colloidal nanocrystal-polymer complex, admixing the alcohol-soluble colloidal nanocrystal-polymer complex and a sol-gel precursor material, and, forming the solid composite from the admixture. The present invention is also directed to the resultant solid composites and to the alcohol-soluble colloidal nanocrystal-polymer complexes.

  15. Multiscale modeling of polyelectrolyte gels

    NASA Astrophysics Data System (ADS)

    Wallmersperger, Thomas; Wittel, Falk K.; Kröplin, Bernd H.

    2006-03-01

    Electrolyte polymer gels are a very attractive class of actuation materials with remarkable electronic and mechanical properties having a great similarity to biological contractile tissues. They consist of a polymer network with ionizable groups and a liquid phase with mobile ions. Absorption and delivery of solvent lead to a considerably large change of volume. Due to this capability, they can be used as actuators for technical applications, where large swelling and shrinkage is desired. In the present work chemically and electrically stimulated polymer gels in a solution bath are investigated. To describe the different complicated phenomena occurring in these gels adequately, the modeling can be conducted on different scales. Therefore, models based on the statistical theory and porous media theory, as well as a multi-field model and a discrete element formulation are derived. A refinement of the different theories from global macroscopic to microscopic are presented in this paper: The statistical theory is a macroscopic theory capable to describe the global swelling or bending e.g. of a gel film, while the general theory of porous media (TPM) is a macroscopic continuum theory which is based on the theory of mixtures extended by the concept of volume fractions. The TPM is a homogenized model, i.e. all geometrical and physical quantities can be seen as statistical averages of the real quantities. The presented chemo-electro-mechanical multi-field formulation is a mesoscopic theory. It is capable of giving the concentrations and the electric potential in the whole domain. Finally the (micromechanical) discrete element (DE) theory is employed. In this case, the continuum is represented by distributed particles with local interaction relations combined with balance equations for the chemical field. This method is predestined for problems involving large displacements, strains and discontinuities. The presented formulations are compared and conclusions on their

  16. Synthesis, characterization, swelling and dye adsorption properties of starch incorporated acrylic gels.

    PubMed

    Mandal, Bidyadhar; Ray, Samit Kumar

    2015-11-01

    Several hydrogels were prepared by a free radical polymerization of acrylic acid (AA), sodium acrylate (SA) and AA/hydroxy ethyl methacrylate (HEMA) in the presence of starch in water. These starch incorporated acrylic gels were prepared by varying the concentration of the initiator, monomer, crosslinker and the starch. The resulting gels were characterized by FTIR, SEM, XRD, DTA-TGA, pH at point zero charge (PZC), swelling and the diffusion in water. The gels showed high adsorption and removal% of Safranine T (ST) and Brilliant Cresyl Blue (BCB) dyes from water. The swelling and the adsorption data were fitted to different kinetic models and isotherms. Amongst the three kinds of gels, the starch incorporated sodium polyacrylate gel showed the highest adsorption of 9.7-85.3mg/L (97-61% removal) of BCB dye and 9.1-83mg/L (91-60% removal) of ST dye for a feed dye concentration of 10-140mg/L. PMID:26318665

  17. Development of novel Sol-Gel Indicators (SGI's) for in-situ environmental measurements: Part 1, Program and a new pH Sol-Gel Indicator

    SciTech Connect

    Livingston, R.R.; Baylor, L.; Wicks, G.G.

    1992-11-03

    The feasibility of incorporating analytical indicators into a sol-gel glassy matrix and then coating substrates with this composite material has bee demonstrated. Substrates coated include paper, wood, glass, and the lens of an analytical probe. The first SRTC sol-gel indicator, comprising bromophenol blue dispersed in a silica matrix, was fabricated and successfully used to measure solution pH in the range of pH 3.0 to 7.5. material exhibited a quick response time, as measured by color changes both qualitatively and quantitatively, and the measuring device was reversible or reusable. Additional indicators with responses over other ranges as well as indicators sensitive to the presence of elements of interest, are also under development. The new SGI composites possess promising properties and an excellent potential for performing a variety important in-situ environmental measurements and area discussed in this report.

  18. Selective gel system for permeability profile control

    SciTech Connect

    Shu, P.

    1990-02-27

    This patent describes a process for closing pores in a more permeable zone of a formation. It comprises: placing into an aqueous solution a first composition sufficient to form ex-situ a size selective, shear thinning first gel which comprises a xanthan biopolymer, and a transitional metal ion; placing into the aqueous solution a second composition sufficient to form thermally a second in-situ gel which is substantially more resistant to formation conditions than the first gel. The composition comprises an aldehyde, and a phenolic compound; allowing the aqueous solution sufficient time to form the ex-situ gel; and injecting the aqueous solution containing the gel into the permeable zone where it reheals, is heated by the formation and thereafter forms a solid gel substantially more resistant to formation conditions than the first gel.

  19. Study of a non-diffusing radiochromic gel dosimeter for 3D radiation dose imaging

    NASA Astrophysics Data System (ADS)

    Marsden, Craig Michael

    2000-12-01

    This thesis investigates the potential of a new radiation gel dosimeter, based on nitro-blue tetrazolium (NBTZ) suspended in a gelatin mold. Unlike all Fricke based gel dosimeters this dosimeter does not suffer from diffusive loss of image stability. Images are obtained by an optical tomography method. Nitro blue tetrazolium is a common biological indicator that when irradiated in an aqueous medium undergoes reduction to a highly colored formazan, which has an absorbance maximum at 525nm. Tetrazolium is water soluble while the formazan product is insoluble. The formazan product sticks to the gelatin matrix and the dose image is maintained for three months. Methods to maximize the sensitivity of the system were evaluated. It was found that a chemical detergent, Triton X-100, in combination with sodium formate, increased the dosimeter sensitivity significantly. An initial G-value of formazan production for a dosimeter composed of 1mM NBTZ, gelatin, and water was on the order of 0.2. The addition of Triton and formate produced a G-value in excess of 5.0. The effects of NBTZ, triton, formate, and gel concentration were all investigated. All the gels provided linear dose vs. absorbance plots for doses from 0 to >100 Gy. It was determined that gel concentration had minimal if any effect on sensitivity. Sensitivity increased slightly with increasing NBTZ concentration. Triton and formate individually and together provided moderate to large increases in dosimeter sensitivity. The dosimeter described in this work can provide stable 3D radiation dose images for all modalities of radiation therapy equipment. Methods to increase sensitivity are developed and discussed.

  20. Prussian Blue as a Prebiotic Reagent

    NASA Astrophysics Data System (ADS)

    Ruiz-Bermejo, M.; Menor-Salván, C.; Osuna-Esteban, S.; Veintemillas-Verdaguer, S.

    2009-12-01

    Ferrocyanide has been proposed as a potential prebiotic reagent and the complex salt Prussian Blue, Fe4[Fe(CN)6]3, might be an important reservoir of HCN, in the early Earth. HCN is considered the main precursor of amino acids and purine and pyrimidine bases under prebiotic conditions. Recently, we observed the formation of Prussian Blue in spark discharge experiments using saline solutions of ferrous chloride, FeCl2. Using Prussian Blue as starting material in ammonium suspensions, we obtained organic compounds containing nitrogen. These results seem to indicate that Prussian Blue could have been first, a sink of HCN, and then in subsequent reactions, triggered by pH fluctuations, it might have lead to organic life precursors.

  1. Blue Origin Conducts Pad Escape Test

    NASA Video Gallery

    Blue Origin conducted a successful pad escape test Oct. 19 at the company's West Texas launch site, firing its pusher escape motor and launching a full-scale suborbital crew capsule from a simulate...

  2. Blue Ribbon Panel Report - BRP - Cancer Moonshot

    Cancer.gov

    The Blue Ribbon Panel Report outlines 10 recommendations to accelerate progress against cancer. The panel was established to ensure that the Cancer Moonshot's approaches are grounded in the best science.

  3. Blue Origin Tests BE-3 Engine

    NASA Video Gallery

    Blue Origin successfully fires the thrust chamber assembly for its new 100,000 pound thrust BE-3 liquid oxygen, liquid hydrogen rocket engine. As part of the company's Reusable Booster System (RBS)...

  4. Blue Ribbon Panel 2016 Video Playlist

    Cancer.gov

    Blue Ribbon Panel members discuss recommendations from the panel report that was presented to the National Cancer Advisory Board on September 7, 2016. The playlist includes an overview video and 10 videos on the specific recommendations.

  5. Blue Ribbon Commission Tour of Hanford Site

    ScienceCinema

    Paul Saueressig

    2010-09-01

    The Blue Ribbon Commission on America's Nuclear Future toured the Department of Energy's Hanford Site on July 14, 2010. Commission members, invited guests, and members of the public visited facilities that store high-level, radioactive waste.

  6. Blue irradiance intercomparison in the medical field

    NASA Astrophysics Data System (ADS)

    Ferreira, Antonio F. G.

    2012-10-01

    This work presents the results of a blue irradiance intercomparison among industrial laboratories of medical devices companies. This intercomparison aims to support the metrological issues of medical equipment manufactures regarding the blue irradiance infant phototherapy equipment requirements on the international standard IEC 60601-2-50:2000. The results showed a low agreement of participants' measurements according to normalized error criterion. The major explanation for this result is associated to an incorrect equipment choice and long recalibration period.

  7. Studies on plasma processing of blue dust

    NASA Astrophysics Data System (ADS)

    Samal, S. K.; P, Sindhoora L.; Mishra, S. C.; Mishra, B.

    2015-02-01

    Plasma smelting was carried out using blue dust and petroleum coke mixtures for five different compositions. By altering percentage of reductant and type of plasma forming gas, recovery rate and degree of metallization were calculated in order to examine the extent of reduction of blue dust. The products were characterized by XRD and optical microscopy techniques. The results of these investigations exhibited that highest degree of metallization and recovery rate of about 98% and 86% respectively, were achieved for nitrogen plasma smelted products.

  8. Barium Enhancement in NGC 6819 Blue Stragglers

    NASA Astrophysics Data System (ADS)

    Milliman, Katelyn; Mathieu, Robert D.; Schuler, Simon C.

    2015-01-01

    Possible formation pathways for blue straggler stars include mergers in hierarchical triple systems, stellar collisions during dynamical encounters, and mass transfer from a giant companion. Extensive work on the blue stragglers in the old open cluster NGC 188 (7 Gyr) has led to exciting discoveries including a binary secondary mass distribution peaked at 0.5 MSolar and the detection of three young white dwarf binary companions. These indicate that mass transfer from an asymptotic giant branch star is the dominant mechanism for blue straggler formation in open clusters. Such mass transfer events should pollute the surface abundance of the blue straggler with nucleosynthesis products from the evolved donor. The other formation pathways, mergers and collisions, are predicted to produce no such enhancements. In an effort to move beyond NGC 188 and into other open clusters we present the first results of a surface abundance study of the blue stragglers in the intermediate-aged open cluster NGC 6819 (2.5 Gyr) using the Hydra multi-object spectrograph on the WIYN 3.5 m telescope. This part of our study centers on the s-process element barium as a tracer of formation via mass transfer. We compare the blue straggler surface abundance of barium to that of a sample of main-sequence stars in NGC 6819 and find multiple blue stragglers with anomalous abundances. Surprising, most of the blue stragglers with barium anomalies show no radial-velocity evidence for a companion. We gratefully acknowledge funding from the National Science Foundation under grant AST- 0908082 and the Wisconsin Space Grant Consortium.

  9. Axion isocurvature fluctuations with extremely blue spectrum

    SciTech Connect

    Kasuya, Shinta; Kawasaki, Masahiro

    2009-07-15

    We construct an axion model for generating isocurvature fluctuations with blue spectrum, n{sub iso}=2-4, which is suggested by recent analyses of admixture of adiabatic and isocurvature perturbations with independent spectral indices, n{sub ad}{ne}n{sub iso}. The distinctive feature of the model is that the spectrum is blue at large scales while scale invariant at small scales. This is naturally realized by the dynamics of the Peccei-Quinn scalar field.

  10. Stylish or safe blue-block eyewear

    NASA Astrophysics Data System (ADS)

    Ciosek, Jerzy

    1998-10-01

    The subject of modern, save and stylish eyewear is entertaining not only to people with unwell eyesight. Many people use glasses with anti-UV or blue-block coatings, glasses for driving or working with a computer. There were investigated the blue-block eyewear. There were analyzed reflected radiation at 300 - 400 nm wavelengths with cross- incidence. The traditional eyewear with classical or stylish frame may not protect sight against the UV radiation.

  11. MitoBlue: a nontoxic and photostable blue-emitting dye that selectively labels functional mitochondria.

    PubMed

    Sánchez, Mateo I; Martínez-Costas, José; Mascareñas, José L; Vázquez, M Eugenio

    2014-12-19

    We report the discovery of a fluorogenic dye, N(1),N(3)-di(2-aminidonaphthalen-6-yl) propane-1,3-diamine, MitoBlue, which selectively stains functional mitochondria while displaying low toxicity, bright blue emission, and high resistance to photobleaching. Additionally, we show that a biotin-labeled MitoBlue derivative can be used as a handle for the delivery of streptavidin-tagged species to the mitochondria. PMID:25325672

  12. MitoBlue: A Nontoxic and Photostable Blue-Emitting Dye That Selectively Labels Functional Mitochondria

    PubMed Central

    2014-01-01

    We report the discovery of a fluorogenic dye, N1,N3-di(2-aminidonaphthalen-6-yl) propane-1,3-diamine, MitoBlue, which selectively stains functional mitochondria while displaying low toxicity, bright blue emission, and high resistance to photobleaching. Additionally, we show that a biotin-labeled MitoBlue derivative can be used as a handle for the delivery of streptavidin-tagged species to the mitochondria. PMID:25325672

  13. Blue-white screening liquid can eliminate false positives in blue-white colony screening.

    PubMed

    Zhang, Y S

    2016-01-01

    Although blue-white screening based on α-complementation has been widely used in the screening of genetically modified bacteria, only a single blue-white screening is typically not enough to eliminate false positives. Sometimes, a secondary blue-white screening for the target colonies is required. In this study, two methods were used to investigate the feasibility of secondary blue-white screening for target colonies on lysogeny broth (LB)-ampicillin agar plates. The first method consisted of covering the target colonies grown on LB-ampicillin plate medium with a sterilized filter paper soaked in a solution of 60 μL 20 mg/mL X-gal and 8 μL 20% IPTG. The second method was that blue and white colonies were randomly selected from the blue-white screening plate medium and then re-streaked onto the blue-white screening medium. The colonies were then treated by two methods and incubated at 37°C for 12 h. The results showed that some of the white colonies treated by the two methods showed results similar to the colonies grown on the blue-white screening medium. These results indicate that the target colonies grown on blue-white screening medium can still be used to carry out a secondary blue-white screening. Thus, a blue-white screening liquid was successfully developed. Using the blue-white screening liquid, false positives can be eliminated directly based on the color of the target colonies. This will greatly improve the screening efficiency of positive clones and has important practical implications. PMID:27323169

  14. Dosimetry aspects of a non-diffusing genipin-gelatin gel

    NASA Astrophysics Data System (ADS)

    Davies, J. B.; Bosi, S. G.; Baldock, C.

    2013-02-01

    Genipin-gelatin gel shows promise as a stable, three-dimensional dosimeter for use in quality assurance for radiotherapy treatments. Genipin creates cross-links in gelatin, forming a blue colour that bleaches quantitatively upon irradiation. A formulation suitable for dosimetry was investigated by varying the concentrations of genipin, gelatin and sulphuric acid and determining the dose sensitivity. An important parameter of the gel preparation that affects dose sensitivity is the temperature at which the cross-linking reaction takes place. The most suitable formulation for dose measurements in 1 cm pathlength cuvettes was found to be made from 50 μM genipin, 4% w/w gelatin and 100 mM sulphuric acid in the final gel. An evaluation of the diffusion coefficient of chromophores in this gel dosimeter demonstrated that this genipin-gelatin gel is a non-diffusing dosimeter. This dosimeter was also evaluated for stability, dose sensitivity, irradiation and measurement temperature dependence and dose rate dependence. No appreciable dependence on dose rate in the range 0.4-40 Gy min-1 was found. No appreciable dependence on measurement temperature between 15 and 23 °C was found. A slight dependence on irradiation temperature was found and this was used to determine the product of the molar linear absorption coefficient and the radiation chemical yield. Finally, the dosimeter measurement uncertainty was evaluated and this was used to determine the dose resolution. Although the focus of this work is on a genipin-gelatin gel dosimeter, the measurement and calibration techniques presented may be applied to any gel dosimetry system measured spectrophotometrically.

  15. Quantitation of specific proteins in polyacrylamide gels by the elution of Fast Green FCF.

    PubMed

    Gilmore, L B; Hook, G E

    1981-07-01

    The quantitation of proteins in polyacrylamide gels stained with Fast green FCF has been investigated using a modification of the elution technique originally described by Fenner et al. (Fenner, C., Traut, R.R., Mason, D.T. and Wikman-Coffelt, J. (1975) Anal. Biochem. 63, 595--602) for Coomassie Blue and adapted by Medugorac (Medugorac, I. (1979) Basic Res. Cardiol. 74, 406--416) for use with proteins stained with Fast Green FCF. The elution of dye from stained protein was accomplished using 1.0 M NaOH instead of aqueous pyridine as required by the original method. The primary advantages of our modification are that the time required for protein quantitation has been considerably reduced and the use of toxic organic solvents has been eliminated. We have investigated the applicability of the method of several different proteins and our results indicate: (a) The quantity of Fast Green FCF eluted from specific proteins is proportional to the quantity of protein applied to the gel, but varies for each individual protein. (b) The method allows quantitation over a very wide range of protein (1--800 micrograms). (c) Quantitation of protein is independent of the width of the stained bands as well as acrylamide concentration. (d) The method is applicable to gels of many types including disc, slab and continuous gradient gels. (e) Protein can be estimated from the patterns obtained by two-dimensional polyacrylamide gel electrophoresis. (f) The presence of Triton X-100 in gel and protein sample does not affect quantitation; the method is applicable to gels containing SDS provided that SDS is removed prior to staining. (g) Precipitation of protein with 12.5% TCA following electrophoresis does not interfere with quantitation. (h) The reproducibility of the technique is excellent, with standard deviations being less than 10% of the mean in all cases. This method appears highly versatile but requires appropriate standards for the quantitation of individual proteins. PMID:7276424

  16. Blue space geographies: Enabling health in place.

    PubMed

    Foley, Ronan; Kistemann, Thomas

    2015-09-01

    Drawing from research on therapeutic landscapes and relationships between environment, health and wellbeing, we propose the idea of 'healthy blue space' as an important new development Complementing research on healthy green space, blue space is defined as; 'health-enabling places and spaces, where water is at the centre of a range of environments with identifiable potential for the promotion of human wellbeing'. Using theoretical ideas from emotional and relational geographies and critical understandings of salutogenesis, the value of blue space to health and wellbeing is recognised and evaluated. Six individual papers from five different countries consider how health can be enabled in mixed blue space settings. Four sub-themes; embodiment, inter-subjectivity, activity and meaning, document multiple experiences within a range of healthy blue spaces. Finally, we suggest a considerable research agenda - theoretical, methodological and applied - for future work within different forms of blue space. All are suggested as having public health policy relevance in social and public space. PMID:26238330

  17. Blue-phase liquid crystal droplets

    PubMed Central

    Martínez-González, José A.; Zhou, Ye; Rahimi, Mohammad; Bukusoglu, Emre; Abbott, Nicholas L.; de Pablo, Juan J.

    2015-01-01

    Blue phases of liquid crystals represent unique ordered states of matter in which arrays of defects are organized into striking patterns. Most studies of blue phases to date have focused on bulk properties. In this work, we present a systematic study of blue phases confined into spherical droplets. It is found that, in addition to the so-called blue phases I and II, several new morphologies arise under confinement, with a complexity that increases with the chirality of the medium and with a nature that can be altered by surface anchoring. Through a combination of simulations and experiments, it is also found that one can control the wavelength at which blue-phase droplets absorb light by manipulating either their size or the strength of the anchoring, thereby providing a liquid–state analog of nanoparticles, where dimensions are used to control absorbance or emission. The results presented in this work also suggest that there are conditions where confinement increases the range of stability of blue phases, thereby providing intriguing prospects for applications. PMID:26460039

  18. Safe thyroidectomy with intraoperative methylene blue spraying

    PubMed Central

    2012-01-01

    Background We aimed to minimalize operative complications by spraying of methylene blue stain on thyroid glands and the perithyroidal area. Material and methods The intra-operative methylene blue spraying technique was used prospectively on a total of 56 patients who had undergone primary (not recurrent) thyroid surgery for a variety of thyroid diseases. Bilateral total thyroidectomy was performed in all cases. After superior but before inferior pole ligation, 0.5ml of methylene blue was sprayed over the thyroid lobe and perilober area. Tissues, especially parathyroides, the recurrent laryngeal nerve, and the inferior thyroid artery, were identified and evaluated. Results Recurrent laryngeal nerve and arteries were not stained and thus they remained white in all cases while all other tissues were stained blue. Within three minutes parathyroid glands washed out the blue stain and the original yellow color was regained. Thyroid tissue wash-out time was not less than 15 minutes; perithyroideal muscles, tendinous and lipoid structures took no less than 25 minutes. Conclusion The safety of intravascular methylene blue guidance on thyroid surgery is known. This research demonstrates the effectiveness of the spraying technique, a new technique which ensures not only identification of parathyroid glands within three minutes, but also identification of recurrent laryngeal nerves and inferior thyroid arteries. PMID:23148801

  19. [Modified Gedelisa test (electrophoresis in gradient of polyacrylamide gel combined with Elisa test). Applications to Toxoplasma gondii exo-antigens (author's transl)].

    PubMed

    Desgeorges, P T; Ambroise-Thomas, P; Falanga, P; Renversez, J C

    1980-01-01

    The authors describe a modified Gedelisa test made up an electrophorese in gradient polyacrylamide gel plus an Elisa test. The gel gradient, after electrophoretic migration is cut longitudinaly. One half is stained with Coomassie blue and the second half is cut in slices of 1 mm thick. Each slice is placed in a well of a microtitration polystirene plate, filled up with carbonate buffer pH 9,6 and then scrached. Proteins diffuse out of the gel and coated on the polystirene. The antigenicity of the coated proteins is revealed by Elisa test. This technique was applied to the study of Toxoplasma gondii exo-antigens obtained from medium of in vitro culture on Vero cells. This antigen contains four fractions, three of them are stained with Coomassie blue, their molecular weights are 160 000, 830 000 and more than one million daltons. PMID:7212392

  20. Metal-silica sol-gel materials

    NASA Technical Reports Server (NTRS)

    Stiegman, Albert E. (Inventor)

    2002-01-01

    The present invention relates to a single phase metal-silica sol-gel glass formed by the co-condensation of a transition metal with silicon atoms where the metal atoms are uniformly distributed within the sol-gel glass as individual metal centers. Any transition metal may be used in the sol-gel glasses. The present invention also relates to sensor materials where the sensor material is formed using the single phase metal-silica sol-gel glasses. The sensor materials may be in the form of a thin film or may be attached to an optical fiber. The present invention also relates to a method of sensing chemicals using the chemical sensors by monitoring the chromatic change of the metal-silica sol-gel glass when the chemical binds to the sensor. The present invention also relates to oxidation catalysts where a metal-silica sol-gel glass catalyzes the reaction. The present invention also relates to a method of performing oxidation reactions using the metal-silica sol-gel glasses. The present invention also relates to organopolymer metal-silica sol-gel composites where the pores of the metal-silica sol-gel glasses are filled with an organic polymer polymerized by the sol-gel glass.

  1. 49 CFR 218.23 - Blue signal display.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 4 2011-10-01 2011-10-01 false Blue signal display. 218.23 Section 218.23..., DEPARTMENT OF TRANSPORTATION RAILROAD OPERATING PRACTICES Blue Signal Protection of Workers § 218.23 Blue signal display. (a) Blue signals displayed in accordance with § 218.25, 218.27, or 218.29 signify...

  2. 49 CFR 218.23 - Blue signal display.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Blue signal display. 218.23 Section 218.23..., DEPARTMENT OF TRANSPORTATION RAILROAD OPERATING PRACTICES Blue Signal Protection of Workers § 218.23 Blue signal display. (a) Blue signals displayed in accordance with § 218.25, 218.27, or 218.29 signify...

  3. Comparison of Alcian Blue, Trypan Blue, and Toluidine Blue for Visualization of the Primo Vascular System Floating in Lymph Ducts

    PubMed Central

    Kim, Da-Un; Han, Jae Won; Jung, Sharon Jiyoon; Lee, Seung Hwan; Cha, Richard; Chang, Byung-Soo; Soh, Kwang-Sup

    2015-01-01

    The primo vascular system (PVS), floating in lymph ducts, was too transparent to be observed by using a stereomicroscope. It was only detectable with the aid of staining dyes, for instance, Alcian blue, which was injected into the lymph nodes. Some dyes were absorbed preferentially by the PVS than the lymph wall. It remains a standing problem to know what dyes are absorbed better by the PVS than the lymph walls. Such information would be useful to unravel the biochemical properties of the PVS that are badly in need for obtaining large amount of PVS specimens. In the current work we tried two other familiar dyes which were used in PVS research before. We found that Trypan blue and toluidine blue did not visualize the PVS. Trypan blue was cleared by the natural washing. Toluidine blue did not stain the PVS, but it did leave stained spots in the lymph wall and its surrounding tissues, and it leaked out of the lymph wall to stain surrounding connective tissues. These completely different behaviors of the three dyes were found for the first time in the current work and provide valuable information to elucidate the mechanism through which some special dyes stained the PVS preferentially compared to the lymphatic wall. PMID:26379749

  4. Allergic contact dermatitis caused by the blue pigment VINAMON® Blue BX FW - a phthalocyanine blue in a vinyl glove.

    PubMed

    Weimann, Stefanie; Skudlik, Christoph; John, Swen Malte

    2010-10-01

    A 44-year-old metalworker suffered from severe hand eczema in spite of treatment with corticosteroid ointments. He had been using protective cotton gloves with blue PVC anti-slip dots on the finger tips. On clinical examination, the backs of both hands were erythematous and thickened while the finger tips showed vesicles. There was a positive patch test reaction to the blue PVC dots of an unworn cotton glove at 72, 96, 120 hours. To identify the causative chemicals, we carried out further patch tests using ingredients of the glove and cupric sulfate. The patient reacted to the blue dye VYNAMON(®) Blue BX FW (PB 15) at two concentrations - 10% at 72 and 96 hours, and 50% at 48 and 72 hours. This dye is a very strong and brilliant blue with red-copper tones and resistant to fire and weathering. The cupric-phthalocyanine complexes are used as pigments in cosmetics (e. g. CI 74160, 74180, 74260). To the best of our knowledge, no allergic reactions to this dye have been described, particularly not in gloves. PMID:20163502

  5. Synthesis and application of a new cleavable linker for "click"-based affinity chromatography.

    PubMed

    Landi, Felicetta; Johansson, Conny M; Campopiano, Dominic J; Hulme, Alison N

    2010-01-01

    A new chemically-cleavable linker has been synthesised for the affinity-independent elution of biomolecules by classical affinity chromatography. This azo-based linker is shown to couple efficiently with "click" derivatised ligands such as biotin propargyl amide through a copper(I)-catalysed Huisgen 1,3-dipolar cycloaddition reaction. Binding to Affi-Gel matrices displaying ligands coupled to the new linker is both efficient and selective. The captured material may be readily released from the resin upon treatment with sodium dithionite. These mild elution conditions have allowed for the efficient isolation of the affinity partner from complex protein mixtures such as those found in fetal bovine serum. PMID:20024132

  6. Variations on the "Blue-Bottle" Demonstration Using Food Items That Contain FD&C Blue #1

    ERIC Educational Resources Information Center

    Staiger, Felicia A.; Peterson, Joshua P.; Campbell, Dean J.

    2015-01-01

    Erioglaucine dye (FD&C Blue #1) can be used instead of methylene blue in the classic "blue-bottle" demonstration. Food items containing FD&C Blue #1 and reducing species such as sugars can therefore be used at the heart of this demonstration, which simply requires the addition of strong base such as sodium hydroxide lye.

  7. 76 FR 19466 - Wellpoint, Inc. D/B/A/Anthem Blue Cross & Blue Shield, et al.; Amended Certification Regarding...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-07

    ... January 26, 2011 (76 FR 4731). At the request of the State agency, the Department reviewed the... Employment and Training Administration Wellpoint, Inc. D/B/A/Anthem Blue Cross & Blue Shield, et al.; Amended.../Anthem Blue Cross & Blue Shield Enterprise Provider Data Management Team Including On-Site Leased...

  8. Automated apparatus for producing gradient gels

    DOEpatents

    Anderson, Norman L.

    1986-01-01

    Apparatus for producing a gradient gel which serves as a standard medium for a two-dimensional analysis of proteins, the gel having a density gradient along its height formed by a variation in gel composition, with the apparatus including first and second pumping means each including a plurality of pumps on a common shaft and driven by a stepping motor capable of providing small incremental changes in pump outputs for the gel ingredients, the motors being controlled, by digital signals from a digital computer, a hollow form or cassette for receiving the gel composition, means for transferring the gel composition including a filler tube extending near the bottom of the cassette, adjustable horizontal and vertical arms for automatically removing and relocating the filler tube in the next cassette, and a digital computer programmed to automatically control the stepping motors, arm movements, and associated sensing operations involving the filling operation.

  9. Automated apparatus for producing gradient gels

    DOEpatents

    Anderson, N.L.

    1983-11-10

    Apparatus for producing a gradient gel which serves as a standard medium for a two-dimensional analysis of proteins, the gel having a density gradient along its height formed by a variation in gel composition, with the apparatus including first and second pumping means each including a plurality of pumps on a common shaft and driven by a stepping motor capable of providing small incremental changes in pump outputs for the gel ingredients, the motors being controlled, by digital signals from a digital computer, a hollow form or cassette for receiving the gel composition, means for transferring the gel composition including a filler tube extending near the bottom of the cassette, adjustable horizontal and vertical arms for automatically removing and relocating the filler tube in the next cassette, and a digital computer programmed to automatically control the stepping motors, arm movements, and associated sensing operations involving the filling operation.

  10. Selective gel system for permeability profile control

    SciTech Connect

    Shu, P.

    1990-10-16

    This patent describes a selective gel for closing pores in a more permeable zone of a formation. It comprises: an aqueous solution of a first composition sufficient to form ex-situ a size selective, shear thinning first gel which comprises a xanthan biopolymer, and a transitional metal ion; and an aqueous solution of a second composition sufficient to form thermally a second in-situ gel that which comprises and aldehyde, and a phenolic compound which solutions are combined and allowed to form a shearable, rehealable ex-situ gel which can be injected into the permeable zone where it reheals when heated by the formation and thereafter forms a solid gel substantially more resistant to formation conditions than the first gel.

  11. GEM printer: 3D gel printer for free shaping of functional gel engineering materials

    NASA Astrophysics Data System (ADS)

    Furukawa, Hidemitsu; Muroi, Hisato; Yamamoto, Kouki; Serizawa, Ryo; Gong, Jin

    2013-04-01

    In the past decade, several high-strength gels have been developed. These gels are expected to use as a kind of new engineering materials in the fields of industry and medical as substitutes to polyester fibers, which are materials of artificial blood vessels. The gels have both low surface friction and well permeability due to a large amount of water absorbed in the gels, which are superiority of the gels compering to the polyester fibers. It is, however, difficult for gels to be forked structure or cavity structure by using cutting or mold. Consequently, it is necessary to develop the additive manufacturing device to synthesize and mode freely gels at the same time. Here we try to develop an optical 3D gel printer that enables gels to be shaped precisely and freely. For the free forming of high-strength gels, the 1st gels are ground to particles and mixed with 2nd pregel solution, and the mixed solution is gelled by the irradiation of UV laser beam through an optical fiber. The use of the optical fiber makes one-point UV irradiation possible. Since the optical fiber is controlled by 3D-CAD, the precise and free molding in XYZ directions is easily realized. We successfully synthesized tough gels using the gel printer.

  12. Microfluidics of soft granular gels

    NASA Astrophysics Data System (ADS)

    Nixon, Ryan; Bhattacharjee, Tapomoy; Sawyer, W. Gregory; Angelini, Thomas E.

    Microfluidic methods for encapsulating cells and particles typically involve drop making with two immiscible fluids. The main materials constraint in this approach is surface tension, creating inherent instability between the two fluids. We can eliminate this instability by using miscible inner and outer phases. This is achieved by using granular micro gels which are chemically miscible but physically do not mix. These microgels are yield stress materials, so they flow as solid plugs far from shear gradients, and fluidize where gradients are generated - near an injection nozzle for example. We have found that tuning the yield stress of the material by varying polymer concentration, device performance can be controlled. The solid like behavior of the gel allows us to produces infinitely stable jets that maintain their integrity and configuration over long distances and times. These properties can be combined and manipulated to produce discrete particulate bunches of an inner phase, flowing inside of an outer phase, well enough even to print a Morse code message suspended within flow chambers about a millimeter in diameter moving at millimeters a second.

  13. Self-Pumping Active Gel

    NASA Astrophysics Data System (ADS)

    Wu, Kun-Ta; Hishamunda, Jean Bernard; Fraden, Seth; Dogic, Zvonimir

    Isotropic active gels are the network which is consist of cross-linked building blocks and the structure of which changes randomly and isotropically with time. Dogic et. al. show that pairs of anti-parallel microtubules form extensile bundles, which merge, extend, and buckle. In an unconfined system, the dynamics of these bundles causes spontaneous turbulent-like flow driven by motion of microscopic molecular motors. We found that confining these active gels in a millimeter sized toroids causes a transition into a new dynamical state characterized by circulation currents persisting for hours until ATP is depleted. We show how toroid dimensions impact the properties of self-organized circular currents, how directions of circulation can be designed by engineering ratchet-shaped boundaries, and how circulations of connected toroids can be either synchronized or antisynchronized. Furthermore, we demonstrate that the flow rate in the circulation is independent of curvature and length of flow path. The flow rate persists for centimeters without decay, disregarding conventional pipe flow resistance. Such findings pave the path to self-pumping pipe transport and performing physical work with biological system.

  14. [Electron microscopy study of artificial vitreous gel].

    PubMed

    Ehgartner, E M; Schmut, O; Hofmann, H

    1986-04-01

    Artificial gels prepared from Cu2+-ions and hyaluronic acid were studied in the electron microscope and compared with the native vitreous body. Additionally, the authors attempted to produce transparent gels from the native constituents of the vitreous body, namely collagen and hyaluronic acid. Mixing of solutions of these constituents formed no gels but white precipitates. The ultrastructure of these precipitates was also studied in the electron microscope. PMID:3723971

  15. Gel time of calcium acrylate grouting material.

    PubMed

    Han, Tong-Chun

    2004-08-01

    Calcium acrylate is a polymerized grout, and can polymerize in an aqueous solution. The polymerization reaction utilizes ammonium persulfate as a catalyst and sodium thiosulfate as the activator. Based on the theory of reaction kinetics, this study on the relation between gel time and concentration of activator and catalyst showed that gel time of calcium acrylate is inversely proportional to activator and catalyst concentration. A formula of gel time is proposed, and an example is provided to verify the proposed formula. PMID:15236477

  16. Formation Channels for Blue Straggler Stars

    NASA Astrophysics Data System (ADS)

    Davies, Melvyn B.

    In this chapter we consider two formation channels for blue straggler stars: (1) the merger of two single stars via a collision, and (2) those produced via mass transfer within a binary. We review how computer simulations show that stellar collisions are likely to lead to relatively little mass loss and are thus effective in producing a young population of more-massive stars. The number of blue straggler stars produced by collisions will tend to increase with cluster mass. We review how the current population of blue straggler stars produced from primordial binaries decreases with increasing cluster mass. This is because exchange encounters with third, single stars in the most massive clusters tend to reduce the fraction of binaries containing a primary close to the current turn-off mass. Rather, their primaries tend to be somewhat more massive and have evolved off the main sequence, filling their Roche lobes in the past, often converting their secondaries into blue straggler stars (but more than 1 Gyr or so ago and thus they are no longer visible today as blue straggler stars).

  17. Triboelectric Nanogenerators for Blue Energy Harvesting.

    PubMed

    Khan, Usman; Kim, Sang-Woo

    2016-07-26

    Blue energy in the form of ocean waves offers an enormous energy resource. However, it has yet to be fully exploited in order to make it available for the use of mankind. Blue energy harvesting is a challenging task as the kinetic energy from ocean waves is irregular in amplitude and is at low frequencies. Though electromagnetic generators (EMGs) are well-known for harvesting mechanical kinetic energies, they have a crucial limitation for blue energy conversion. Indeed, the output voltage of EMGs can be impractically low at the low frequencies of ocean waves. In contrast, triboelectric nanogenerators (TENGs) are highly suitable for blue energy harvesting as they can effectively harvest mechanical energies from low frequencies (<1 Hz) to relatively high frequencies (∼kHz) and are also low-cost, lightweight, and easy to fabricate. Several important steps have been taken by Wang's group to develop TENG technology for blue energy harvesting. In this Perspective, we describe some of the recent progress and also address concerns related to durable packaging of TENGs in consideration of harsh marine environments and power management for an efficient power transfer and distribution for commercial applications. PMID:27408982

  18. GEMS: The destiny of Blue Spheroidal Galaxies

    NASA Astrophysics Data System (ADS)

    Häußler, Boris; Bell, Eric F.; Barden, Marco; McIntosh, Daniel H.; Rix, Hans-Walter; Borch, Andrea; Beckwith, Steven V. W.; Caldwell, John A. R.; Heymans, Catherine; Jahnke, Knud; Jogee, Shardha; Koposov, Sergey E.; Meisenheimer, Klaus; Peng, Chien Y.; Sánchez, Sebastian F.; Somerville, Rachel S.; Wisotzki, Lutz; Wolf, Christian

    2007-05-01

    One of the key predictions of hierarchical galaxy formation models is that a significant fraction of elliptical galaxies form in late merging events. One of the most important observations of such an assembly is the existence of blue spheroidal galaxies, which have spheroid-dominated morphologies and blue colors indicating recent star formation, as an intermediate step in the evolution of elliptical galaxies. We present results from the GEMS survey showing the properties of these galaxies derived from 2-D galaxy fitting of the ˜8000 galaxies with photometric redshifts in the 28'x28' HST mosaic. For the first time we were able to divide the observed population of blue elliptical galaxies into sub-populations of different stellar masses. We found that massive blue ellipticals are likely to be the progenitors of red elliptical galaxies while low-mass blue ellipticals have half-light radii considerably in excess of those measured for low-mass present day elliptical galaxies and instead have larger sizes similar to present-day disk-dominated systems with substantial bulges (see Figure)

  19. "Blue and seven phenomena" among Japanese students.

    PubMed

    Saito, M

    1999-10-01

    To investigate color and number preferences in Japan, 586 university undergraduates (239 men and 347 women; M age = 20.9 yr.) were asked to name a color (Question 1), to name their preferred color (Question 2), and to name their preferred number between zero and nine (Question 3). The results showed that Japanese students chose blue (33.5%) or red (26.0%) when asked to name a color but that red was not chosen as frequently as blue as a preferred color (red: 11.1%, blue: 37.1%). Sex differences were found on both Questions 1 and 2 by chi-squared test. Black was chosen more by men, while pink was selected more by women. 22.5% subjects also selected the number seven, supporting Simon's observation of the "blue-seven phenomenon." The reasons given for the choice showed that seven was "a lucky number" and "represented happiness" among Japanese students. Four colors (blue, red, white, and black) accounted for 76.8% and 65.1% of responses to Questions 1 and 2, respectively, and odd numbers 68.4% for Question 3. PMID:10597589

  20. Conducting Polymer Electrodes for Gel Electrophoresis

    PubMed Central

    Bengtsson, Katarina; Nilsson, Sara; Robinson, Nathaniel D.

    2014-01-01

    In nearly all cases, electrophoresis in gels is driven via the electrolysis of water at the electrodes, where the process consumes water and produces electrochemical by-products. We have previously demonstrated that π-conjugated polymers such as poly(3,4-ethylenedioxythiophene) (PEDOT) can be placed between traditional metal electrodes and an electrolyte to mitigate electrolysis in liquid (capillary electroosmosis/electrophoresis) systems. In this report, we extend our previous result to gel electrophoresis, and show that electrodes containing PEDOT can be used with a commercial polyacrylamide gel electrophoresis system with minimal impact to the resulting gel image or the ionic transport measured during a separation. PMID:24586761

  1. Functional behavior of isotropic magnetorheological gels

    NASA Astrophysics Data System (ADS)

    Venkateswara Rao, P.; Maniprakash, S.; Srinivasan, S. M.; Srinivasa, A. R.

    2010-08-01

    Magnetorheological (MR) gels are a new class of soft polymers whose properties can be controlled using a magnetic field. The functional effectiveness of these gels depends on their magnetic controllability. In this paper, an experimental investigation on the functional behavior of a particular type of magnetorheological gels under dynamic and static shear conditions in the presence of a magnetic field is studied. MR gels are prepared with micron sized polarizable carbonyl iron particles interspersed in a polymer matrix gel. The compliance of this magnetic gel can be varied under the influence of an external magnetic field. Since dynamical mechanical analysis tests are difficult to conduct in the presence of large deformations of the order of 50% and strong magnetic fields, a free decay test apparatus is designed and fabricated for obtaining the magnetic field dependent shearing response under dynamic conditions at room temperature. It is observed that a significant change in the elastic modulus occurs in the gels under a magnetic field in the range of 0.1-0.4 T. However, no significant change in the damping ratio is observed under various magnitudes of magnetic field. It is shown that the increase in shear modulus of this kind of magnetic composite gel could be as high as 59% of the zero field value for a gel prepared with 50% by weight of carbonyl iron particles.

  2. Tissue simulating gel for medical research

    NASA Technical Reports Server (NTRS)

    Companion, John A. (Inventor)

    1991-01-01

    A tissue simulating gel and a method for preparing the tissue simulating gel are disclosed. The tissue simulating gel is prepared by a process using water, gelatin, ethylene glycol, and a cross-linking agent. In order to closely approximate the characteristics of the type of tissue being simulated, other material has been added to change the electrical, sound conducting, and wave scattering properties of the tissue simulating gel. The result of the entire process is a formulation that will not melt at the elevated temperatures involved in hyperthermia medical research. Furthermore, the tissue simulating gel will not support mold or bacterial growth, is of a sufficient mechanical strength to maintain a desired shape without a supporting shell, and is non-hardening and non-drying. Substances have been injected into the tissue simulating gel prior to the setting-up thereof just as they could be injected into actual tissue, and the tissue simulating gel is translucent so as to permit visual inspection of its interior. A polyurethane spray often used for coating circuit boards can be applied to the surface of the tissue simulating gel to give a texture similar to human skin, making the tissue simulating gel easier to handle and contributing to its longevity.

  3. Ionic liquid based multifunctional double network gel

    NASA Astrophysics Data System (ADS)

    Ahmed, Kumkum; Higashihara, Tomoya; Arafune, Hiroyuki; Kamijo, Toshio; Morinaga, Takashi; Sato, Takaya; Furukawa, Hidemitsu

    2015-04-01

    Gels are a promising class of soft and wet materials with diverse application in tissue engineering and bio-medical purpose. In order to accelerate the development of gels, it is required to synthesize multi-functional gels of high mechanical strength, ultra low surface friction and suitable elastic modulus with a variety of methods and new materials. Among many types of gel ionic gel made from ionic liquids (ILs) could be used for diverse applications in electrochemical devices and in the field of tribology. IL, a promising materials for lubrication, is a salt with a melting point lower than 100 °C. As a lubricant, ILs are characterized by an extremely low vapor pressure, high thermal stability and high ion conductivity. In this work a novel approach of making double network DN ionic gel using IL has been made utilizing photo polymerization process. A hydrophobic monomer Methyl methacrylate (MMA) has been used as a first network and a hydrophobic IL monomer, N,N-diethyl-N-(2-mthacryloylethyl)-N-methylammonium bistrifluoromethylsulfonyl)imide (DEMM-TFSI) has been used as a second network using photo initiator benzophenon and crosslinker triethylene glycol dimethacrylate (TEGDMA). The resulting DN ionic gel shows transparency, flexibility, high thermal stability, good mechanical toughness and low friction coefficient value which can be a potential candidate as a gel slider in different mechanical devices and can open a new area in the field of gel tribology.

  4. Structure of chitosan gels mineralized by sorption

    NASA Astrophysics Data System (ADS)

    Modrzejewska, Z.; Skwarczyńska, A.; Douglas, T. E. L.; Biniaś, D.; Maniukiewicz, W.; Sielski, J.

    2015-10-01

    The paper presents the structural studies of mineralized chitosan hydrogels. Hydrogels produced by using sodium beta-glycerophosphate (Na-β-GP) as a neutralizing agent. Mineralization was performed method "post loading", which consisted in sorption to the gels structure Ca ions. In order to obtain - in the structure of gels - compounds similar to the hydroxyapatites present naturally in bone tissue, gels after sorption were modified in: pH 7 buffer and sodium hydrogen phosphate. In order to determine the structural properties of the gels, the following methods were used: infrared spectroscopy with Fourier transformation, FTIR, X-ray diffractometry, XRD, scanning electron microscopy, SEM.

  5. Comparison of Catalytic Activities for Sonocatalytic, Photocatalytic and Sonophotocatalytic Degradation of Methylene Blue in the Presence of Magnetic Fe3O4/CuO/ZnO Nanocomposites

    NASA Astrophysics Data System (ADS)

    Taufik, Ardiansyah; Tju, Hendry; Saleh, Rosari

    2016-04-01

    Fe3O4/CuO/ZnO nanocomposites with different molar ratio were synthesized using sol-gel method. The as-synthesized samples were characterized by X-ray diffraction (XRD), UV-visible spectroscopy, BET surface area analyszer, and Electron Spin Resonance (ESR). The sonocatalytic-photocatalytic-sonophotocatalytic activity of as-synthesized samples was investigated based on methylene blue degradation. Moreover, the role of active species was investigated using scavenger technique. The results showed that hole plays an important key role in sono-photo-sonophotocatalytic degradation of methylene blue.

  6. A New Organic Dye-Based Staining for The Detection of Plant DNA in Agarose Gels.

    PubMed

    Sönmezoğlu, Özlem Ateş; Özkay, Kerime

    2015-01-01

    Ethidium bromide (EtBr) is used to stain DNA in agarose gel electrophoresis, but this dye is mutagenic and carcinogenic. We investigated N-719, which is a visible, reliable and organic Ruthenium-based dye, and five fluorescent alternatives for staining plant DNA. For prestaining and poststaining, N-719, GelRed, and SYBR Safe stained both DNA and PCR product bands as clearly as EtBr. SYBR Green I, methylene blue, and crystal violet were effective for poststaining only. The organic dye N-719 stained DNA bands as sensitively and as clearly as EtBr. Consequently, organic dyes can be used as alternatives to EtBr in plant biotechnology studies. PMID:26158569

  7. The porosity of sol-gel silica thin films for optrode applications

    SciTech Connect

    Harris, T.M.; Knobbe, E.T.

    1995-12-01

    Porous silica thin films produced by sol-gel processing are being considered for use in optical sensor (optrode) applications. In this study, thin films were produced by dip-coating onto glass slides. The porosity was then measured indirectly, by determining the amount of methylene blue adsorption on each slide. Using this technique, it has been determined that the {open_quotes}two-step{close_quotes} sol-gel process provides a greater surface area than the acid-catalyzed process. With the two-step process, increasing the amount of solvent (ethanol) and decreasing the rate of slide withdrawal from the sol provided increased surface area when normalized to the mass of the deposit.

  8. Two-dimensional gel-based alkaline proteome of the probiotic bacterium Lactobacillus acidophilus NCFM.

    PubMed

    Majumder, Avishek; Cai, Liyang; Ejby, Morten; Schmidt, Bjarne G; Lahtinen, Sampo J; Jacobsen, Susanne; Svensson, Birte

    2012-04-01

    Lactobacillus acidophilus NCFM (NCFM) is a well-documented probiotic bacterium isolated from human gut. Detailed 2D gel-based NCFM proteomics addressed the so-called alkaline range, i.e., pH 6-11. Proteins were identified in 150 of the 202 spots picked from the Coomassie Brilliant Blue stained 2D gel using MALDI-TOF-MS. The 102 unique gene products among the 150 protein identifications were assigned to different functional categories, and evaluated by considering a calculated distribution of abundance as well as grand average of hydrophobicity values. None of the very few available lactic acid bacteria proteome reference maps included the range of pI >7.0. The present report of such data on the proteome of NCFM fundamentally complements current knowledge on protein profiles limited to the acid and neutral pH range. PMID:22522807

  9. A microdestructive capillary electrophoresis method for the analysis of blue-pen-ink strokes on office paper.

    PubMed

    Calcerrada, Matías; González-Herráez, Miguel; Garcia-Ruiz, Carmen

    2015-06-26

    This manuscript describes the development of a capillary electrophoresis (CE) method for the detection of acid and basic dyes and its application to real samples, blue-pen-ink strokes on office paper. First, a capillary zone electrophoresis (CZE) method was developed for the separation of basic and acid dyes, by studying the separation medium (buffer nature, pH and relative amount of additive) and instrumental parameters (temperature, voltage and capillary dimensions). The method performance was evaluated in terms of selectivity, resolution (above 5 and 2 for acid dyes and basic dyes, respectively, except for two basic dye standards), LOD (lower than 0.4 mg/L) and precision as intraday and interday RSD values of peak migration times (lower than 0.6%). The developed method was then applied to 34 blue pens from different technologies (rollerball, ballpoint, markers) and with different ink composition (gel, water-based, oil-based). A microdestructive sample treatment using a scalpel to scratch 0.3mg of ink stroke was performed. The entire electropherogram profile allowed the visual discrimination between different types of ink and brands, being not necessary a statistical treatment. A 100% of discrimination was achieved between pen technologies, brands, and models, although non-reproducible zones in the electropherograms were found for blue gel pen samples. The two different batches of blue oil-based pens were also differentiated. Thus, this method provides a simple, microdestructive, and rapid analysis of different blue pen technologies which may complement the current analysis of questioned documents performed by forensic laboratories. PMID:26003620

  10. Stacking gels: A method for maximising output for pulsed-field gel electrophoresis.

    PubMed

    Heng, See Kah; Heng, Chua Kek; Puthucheary, S D

    2009-01-01

    Pulsed field gel electrophoresis (PFGE), the gold standard of molecular typing methods, has a major disadvantage of an unusually long electrophoretic time. From the original protocol of 6 days, it was modified to 3 days and subsequently to a single day. We describe the procedure of stacking five to six gels one on top of another in order to increase and maximize the output in a shorter time without compromising the resolution and reproducibility. All the variables that affect pulsed field gels during electrophoresis were taken into consideration. We firstly optimized the parameters to be used and secondly determined whether stacking of five to six gels had any effect on the molecular separation during electrophoresis in comparison with a single gel run. DNA preparation, restriction, electrophoresis, staining and gel documentation was carried out based on previously published methods. Gels were analysed using BioNumerics and dice coefficient and unweighted pair group methods were used to generate dendrograms based on 1.5% tolerance values. Identical band profiles and band resolution-separation were seen in the PFGE patterns with single gel and multiple stacking gels. Cluster analysis further strengthened the fact that results from stacking gels were reproducible and comparable with a single gel run. This method of stacking gels saves time and maximizes the output at the same time. The run time for a single gel was about 28 hours, but with six stacked gels the run time was 54 hours compared with 28 x 6 = 168 hours if they were run separately as single gels thus saving time of 67.86%. Beside the big factor of saving time, stacking gels save resources (electricity, reagents, water, chemicals and working time) by increasing the sample throughput in a shorter time without compromising on quality of data. But optimization of working parameters is vital depending on the PFGE system used. PMID:19384038

  11. Blue-green atomic mercury photodissociation laser

    NASA Astrophysics Data System (ADS)

    Fill, E.; Gerck, E.

    The accomplishment of a blue-green Hg laser after dissociating HgI2 with a KrF laser is reported. The iodide was contained in a cell with an aluminum mirror, and heating with the KrF laser caused green laser emission at 180 C and a blue line above 210 C, with total emission increasing up to 260 C and then tailing off. The emitted wavelengths were measured at 435-8 and 546.1 nm, with the pulse shape having a duration of 1 ns with peak power of 3 kW for the blue and an order of magnitude less for the green. The KrF laser was tuned to emit at 248 nm, and no decrease in the resulting emissions were detected after 10,000 pulses in the iodide laser.

  12. Blue light inhibits proliferation of melanoma cells

    NASA Astrophysics Data System (ADS)

    Becker, Anja; Distler, Elisabeth; Klapczynski, Anna; Arpino, Fabiola; Kuch, Natalia; Simon-Keller, Katja; Sticht, Carsten; van Abeelen, Frank A.; Gretz, Norbert; Oversluizen, Gerrit

    2016-03-01

    Photobiomodulation with blue light is used for several treatment paradigms such as neonatal jaundice, psoriasis and back pain. However, little is known about possible side effects concerning melanoma cells in the skin. The aim of this study was to assess the safety of blue LED irradiation with respect to proliferation of melanoma cells. For that purpose we used the human malignant melanoma cell line SK-MEL28. Cell proliferation was decreased in blue light irradiated cells where the effect size depended on light irradiation dosage. Furthermore, with a repeated irradiation of the melanoma cells on two consecutive days the effect could be intensified. Fluorescence-activated cell sorting with Annexin V and Propidium iodide labeling did not show a higher number of dead cells after blue light irradiation compared to non-irradiated cells. Gene expression analysis revealed down-regulated genes in pathways connected to anti-inflammatory response, like B cell signaling and phagosome. Most prominent pathways with up-regulation of genes were cytochrome P450, steroid hormone biosynthesis. Furthermore, even though cells showed a decrease in proliferation, genes connected to the cell cycle were up-regulated after 24h. This result is concordant with XTT test 48h after irradiation, where irradiated cells showed the same proliferation as the no light negative control. In summary, proliferation of melanoma cells can be decreased using blue light irradiation. Nevertheless, the gene expression analysis has to be further evaluated and more studies, such as in-vivo experiments, are warranted to further assess the safety of blue light treatment.

  13. Terpolymer smart gels: synthesis and characterizations

    NASA Astrophysics Data System (ADS)

    Bag, Dibyendu S.; Alam, Sarfaraz; Mathur, G. N.

    2004-10-01

    Two smart terpolymer gels, MS-1 and MS-2, were synthesized such that the same gel can respond to more than one external environmental condition, such as pH, temperature, solvent composition, electric field. So two terpolymers gels of vinyl monomers such as sodium acrylate, acrylamide and N-isopropyl acrylamide were synthesized by using ammonium persulfate (APS) as an initiator, N,N,N',N'-tetramethyl ethylene diamine (TMEDA) as an accelerator and methylene bisacrylamide as a cross-linker. These terpolymers were characterized by elemental and Fourier transform infrared analysis. The swelling behavior of these terpolymer smart gels was evaluated by changing the pH, temperature and solvent composition. The variation of the swelling behavior with time was evaluated in an aqueous medium at room temperature. The time taken for maximum swelling (tm) was about 20 min for the gel MS-2. However the tm value for the gel MS-1 is higher than that of MS-2. The swelling behavior remains almost unchanged over a temperature range of 22-50 °C for both the gels. The discontinuous volume transitions were observed at pH 7.6 and 8.2 for the two gels, MS-1 and MS-2, respectively. The gel MS-1 suddenly shrinks below and swells above pH 7.6. Correspondingly, the pH is 8.2 for the case of MS-2. Volume transitions in an acetone-water mixture were also observed for these gels. The swelling behaviors of these two smart gels are almost parallel above the 40% acetone concentration.

  14. Eastward migration of blue-winged teal

    USGS Publications Warehouse

    Sharp, B.

    1972-01-01

    Of 3,789 recoveries of blue-winged teal (Anas discors) banded prior to the hunting season in the prairie pothole region, 183 (4.8 percent) were recovered, due east in New England, Ontario, Quebec, and the Maritime Provinces during the subsequent hunting season. Of 19 recoveries looked at in detail, all were banded as either hatching-year (flying young) or local (flightless young) birds. A blue-winged teal banded in Minnesota in September was retrapped in October in South Carolina, before being shot later that month in Colombia, South America.

  15. Blue Skies, Coffee Creamer, and Rayleigh Scattering

    NASA Astrophysics Data System (ADS)

    Liebl, Michael

    2010-05-01

    The first physical explanation of Earths blue sky was fashioned in 1871 by Lord Rayleigh. Many discussions of Rayleigh scattering and approaches to studying it both in and out of the classroom are available.2-5 Rayleigh scattering accounts for the blue color of the sky and the orange/red color of the Sun near sunset and sunrise, and a number of classroom demonstrations have been described for showing the effects.6-11 This paper describes how these demonstrations can be enhanced by using a spectrometer to measure the preferential scattering of the shorter wavelength light.

  16. Multicolored, Low-Power, Flexible Electrochromic Devices Based on Ion Gels.

    PubMed

    Moon, Hong Chul; Kim, Chang-Hyun; Lodge, Timothy P; Frisbie, C Daniel

    2016-03-01

    Ion gels composed of a copolymer and a room temperature ionic liquid are versatile solid-state electrolytes with excellent features including high ionic conductivity, nonvolatility, easily tunable mechanical properties, good flexibility and solution processability. Ion gels can be functionalized by incorporating redox-active species such as electrochemiluminescent (ECL) luminophores or electrochromic (EC) dyes. Here, we enhance the functionality of EC gels for realizing multicolored EC devices (ECDs), either by controlling the chemical equilibrium between a monomer and dimer of a colored EC species, or by modifying the molecular structures of the EC species. All devices in this work are conveniently fabricated by a "cut-and-stick" strategy, and require very low power for maintaining the colored state [i.e., 90 μW/cm(2) (113 μA/cm(2) at -0.8 V) for blue, 4 μW/cm(2) (10 μA/cm(2) at -0.4 V) for green, and 32 μW/cm(2) (79 μA/cm(2) at -0.4 V) for red ECD]. We also successfully demonstrate a patterned, multicolored, flexible ECD on plastic. Overall, these results suggest that gel-based ECDs have significant potential as low power displays in printed electronics powered by thin-film batteries. PMID:26867428

  17. Sol-gel derived hybrid materials doped with rare earth metal ions

    NASA Astrophysics Data System (ADS)

    Zelazowska, E.; Rysiakiewicz-Pasek, E.; Borczuch-Laczka, M.; Cholewa-Kowalska, K.

    2011-10-01

    Sol-gel derived organic-inorganic hybrid materials doped with rare earth metal ions (Pr 3+) and small amounts of lithium ions (˜0.1-0.2 wt.%) were produced from the tetraethyl orthosilicate (TEOS), AlCl 3·6H 2O (about 10 mol%), ethyl methacrylate, butyl methacrylate and some other organic additions (ca. 35-40 wt.% of organics in the fresh gels) to obtain hybrid organic-inorganic hosts. The gel and hybrid materials obtained were aged at room temperature for three weeks, then heated in an electric drier for 3 h at temperature of 125 °C and investigated for morphology, structure and luminescence properties by X-ray diffraction (XRD), scanning electron microscopy equipped with energy dispersive X-ray spectroscopy (SEM/EDS), Fourier transform infrared spectroscopy (FTIR), 29Si and 27Al MAS nuclear magnetic resonance and fluorescence spectroscopy. An influence of the organic additions and inorganic dopants on microstructure of the materials obtained and their luminescence properties has been examined. Under excitation with UV radiation in a range of ˜210-350 nm, the sharp and relatively intense luminescence emission lines due to 3P 0 → 3H 4 (blue) and 3P 0 → 3F 3 (red) transitions of Pr 3+ ions were observed in the luminescence spectra of gel and hybrid materials of SA-series.

  18. Viscoelastic Properties of Vitreous Gel

    NASA Astrophysics Data System (ADS)

    Pirouz Kavehpour, H.; Sharif-Kashani, Pooria

    2010-11-01

    We studied the rheological properties of porcine vitreous humor using a stressed-control shear rheometer. All experiments were performed in a closed environment at body temperature to mimic in-vivo conditions. We modeled the creep deformation using a two-element retardation spectrum model. By associating each element of the model to an individual biopolymeric system in the vitreous gel, a separate response to the applied stress was obtained from each component. The short time scale was associated with the collagen structure, while the longer time scale was related to the microfibrilis and hyaluronan network. We were able to distinguish the role of each main component from the overall rheological properties. Knowledge of this correlation enables us to relate the physical properties of vitreous to its pathology, as well as optimize surgical procedures such as vitrectomy.

  19. Gel transitions in colloidal suspensions

    NASA Astrophysics Data System (ADS)

    Bergenholtz, J.; Fuchs, M.

    1999-12-01

    The idealized mode-coupling theory (MCT) is applied to colloidal systems interacting via short-range attractive interactions of Yukawa form. At low temperatures, MCT predicts a slowing down of the local dynamics and ergodicity-breaking transitions. The non-ergodicity transitions share many features with the colloidal gel transition, and are proposed to be the source of gelation in colloidal systems. Previous calculations of the phase diagram are complemented with additional data for shorter ranges of the attractive interaction, showing that the path of the non-ergodicity transition line is then unimpeded by the gas-liquid critical curve at low temperatures. Particular attention is given to the critical non-ergodicity parameters; this is motivated by recent experimental measurements. An asymptotic model is developed, valid for dilute systems of spheres interacting via strong short-range attractions, and is shown to capture all aspects of the low-temperature MCT non-ergodicity transitions.

  20. Change in NO2 reveals Parade Blue is cleaner than APEC Blue

    NASA Astrophysics Data System (ADS)

    Liu, Haoran; Liu, Cheng; Xie, Zhouqing; Xie, Pinhua; Xing, Chengzhi; Xu, Jin; Liu, Jianguo

    2016-04-01

    The spectacular Parade Blue (blue sky), and APEC Blue (blue sky) were renowned worldwide caused by the limiting discharge policy of the Chinese government. For evaluating the reduction of these two events, we analyzed the variation of NO2 columns Beijing by looking at a long-term monitoring using Multi-Axis Differential Optical Absorption Spectroscopy (MAX-DOAS) and the Ozone Monitoring Instrument (OMI) satellite observations from August 2014 to November 2015, covering Grand Military Parade (GMP, September 2015) and APEC (November 2014) period. We found that the NO2 columns abruptly decreased both GMP and APEC. However, change in the MAX-DOAS and the OMI NO2 during GMP was larger than during APEC via comparison with the same period in 2014, indicating Parade Blue is cleaner than APEC Blue. The spatial distribution of NO2 and backward trajectories together with meterological parameters suggested that GMP Blue may be due to the regional significant decreasing discharge in peripheral cities. No weekend effect during GMP further confirmed the role of controlling discharge. This study provides direct evidence that it is possible to clean air in China.

  1. A Simple Vertical Slab Gel Electrophoresis Apparatus.

    ERIC Educational Resources Information Center

    Carter, J. B.; And Others

    1983-01-01

    Describes an inexpensive, easily constructed, and safe vertical slab gel kit used routinely for sodium dodecyl sulphate-polyacrylamide gel electrophoresis research and student experiments. Five kits are run from a single transformer. Because toxic solutions are used, students are given plastic gloves and closely supervised during laboratory…

  2. Chain Release Behavior of Gellan Gels

    NASA Astrophysics Data System (ADS)

    Hossain, Khandker S.; Nishinari, Katsuyoshi

    The chain release behavior from gellan gels was studied by immersing the gel into water and monitoring the mass loss as a function of time. Concentration of released gellan in the external solution was determined for gels of different sizes using phenol-sulfuric acid method. The chain release process became faster with increasing total surface area and volume. However the concentration of released chain normalized by surface area and volume suggests that the chain release itself is governed not only by the ionic effect and the amount of unassociated chains in gel but other factors such as osmotic pressure may play an important role on the chain release from the gels. The diffusion coefficient was estimated from the chain release process which is in the same order of magnitude reported for an isolated gellan chain by light scattering. Rheological measurements also suggest that the unassociated gellan chains are released out when immersed in pure water while unassociated chains are restricted to release out when immersed in salt solution due to the intrusion of cations which is responsible for further association of the unassociated gellan chains being in agreement with the previously published results. The elastic modulus of gels was increased by immersion of gels in water and in salt solutions, which can be attributed as the stiffening of network chains due to gel swelling and the conversion from free and unassociated chains into network chains, respectively, leading to an increase in elastic modulus with time.

  3. Sol-gel kinetics by NMR

    SciTech Connect

    Assink, R.A.; Kay, B.D.

    1991-01-01

    The chemical synthesis of advanced ceramic and glass materials by the sol-gel process has become an area of increasing activity in the field of material science. The sol-gel process provides a means to prepare homogeneous, high purity materials with tailored chemical and physical properties. This paper surveyed the nuclear magnetic resonance (NMR) studies of silicon-based sol-gel kinetics. A review of the various models which have been used to analyze the chemical kinetics of various sol-gel systems was presented. The utility of NMR spectroscopy was demonstrated in investigating the influence that various reaction conditions have on the reaction pathways by which sol-gel derived materials are synthesized. By observing in a direct fashion the chemical pathway of the sol-gel, it is often possible to relate the final properties of the material to the formulation and reaction conditions of the sol-gel. The study of reaction kinetics by NMR is expected to play an increasingly important role in understanding sol-gel processing and material properties. 15 refs. (DP)

  4. A Short-Duration Gel Diffusion Experiment.

    ERIC Educational Resources Information Center

    Mulcahy, D. E.

    1980-01-01

    Described is a gel diffusion experiment that permits the completion of duplicate diffusion runs within a three-hour laboratory session. Information included for the short-duration gel diffusion experiment is the diffusion cell, the experiment, data treatment, and the expected results of the experiment. (Author/DS)

  5. 21 CFR 866.4900 - Support gel.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Support gel. 866.4900 Section 866.4900 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunology Laboratory Equipment and Reagents § 866.4900 Support gel....

  6. 21 CFR 866.4900 - Support gel.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Support gel. 866.4900 Section 866.4900 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunology Laboratory Equipment and Reagents § 866.4900 Support gel....

  7. 21 CFR 866.4900 - Support gel.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Support gel. 866.4900 Section 866.4900 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunology Laboratory Equipment and Reagents § 866.4900 Support gel....

  8. 21 CFR 866.4900 - Support gel.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Support gel. 866.4900 Section 866.4900 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunology Laboratory Equipment and Reagents § 866.4900 Support gel....

  9. 21 CFR 866.4900 - Support gel.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Support gel. 866.4900 Section 866.4900 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Immunology Laboratory Equipment and Reagents § 866.4900 Support gel....

  10. Fluorescence detection for gel and capillary electrophoresis

    SciTech Connect

    Hogan, B.

    1992-07-21

    First, an indirect fluorescence detection system for the separation of proteins via gel electrophoresis. Quantities as low as 50 nanograms of bovine serum albumin and soybean trypsin inhibitor are separated and detected visually without the need for staining of the analytes. This is very similar to levels of protein commonly separated with gel electrophoresis.

  11. Transparent poly(vinyl acetate)-silica gels by a sol-gel process

    NASA Astrophysics Data System (ADS)

    Wojcik, Anna B.; Klein, Lisa C.

    1993-12-01

    Rod shaped silica-poly(vinyl acetate) (PVAc) gels have been prepared by a sol gel process. In situ polymerization of tetraethoxysilane (TEOS) was accomplished in the presence of low molecular weight PVAc by dissolving various amounts of PVAc in a mixture of TEOS, ethanol, water and hydrochloric acid (HCl). Gelation of this mixture was carried out between room temperature and slightly above. Silica-PVAc rods recovered from cylindrical molds were homogeneous and transparent. Gels with weight percents of PVAc ranging from 2% to 50% were prepared. Silica-PVAc gels have higher flexure strengths, less brittle character and improved water durability in comparison with pure sol- gel silica.

  12. Thermotropic nanostructured "gel in gel" systems for improved oil recovery and water shutoff

    NASA Astrophysics Data System (ADS)

    Altunina, L. K.; Kuvshinov, V. A.; Stasyeva, L. A.

    2015-10-01

    Thermotropic nanostructured system with two gel-forming components has been created based on inorganic hydroxypolymer and organic polymer with a lower critical solution temperature of "aluminum salt-cellulose ether-carbamide-water", forming at heating a bound-dispersed nano-sized "gel in gel" structure. The studies on the kinetics of gelation and rheological properties of solutions and gels in this system have shown that the gels have a higher viscosity and elasticity and thereby are promising for creating deflecting screens in oil reservoirs, redistribution of filtration flows, improved oil recovery and for water shutoff.

  13. Drop spreading and resorbtion on gel surfaces

    NASA Astrophysics Data System (ADS)

    Banaha, Mehdi; Daerr, Adrian; Limat, Laurent

    2008-03-01

    We have studied the dynamics of liquid drops on agar gels, using a visualisation method which captures the evolution of the free surface. A first remarquable observation is that drops of water deposited on the surface do not spread, although the gel consists of up to 99.7% water and as low as 0.3% agarose. Instead, the drop slowly de-wets and resorbs into the gel which swells locally. If the deposited drop contains surfactants, the dynamics is very different. A sharp circular swelling front develops and progressively invades the whole surface. We study the propagation of this front as a function of surfactant and agarose concentration, and compare its typical properties to similar fronts appearing during mass swarming events of bacterial colonies under the same conditions. The observations reveal the complex nature of gel surface physico-chemistry and its aging, and may be related to recent friction measurements at gel interfaces.

  14. Photoswitchable gel assembly based on molecular recognition.

    PubMed

    Yamaguchi, Hiroyasu; Kobayashi, Yuichiro; Kobayashi, Ryosuke; Takashima, Yoshinori; Hashidzume, Akihito; Harada, Akira

    2012-01-01

    The formation of effective and precise linkages in bottom-up or top-down processes is important for the development of self-assembled materials. Self-assembly through molecular recognition events is a powerful tool for producing functionalized materials. Photoresponsive molecular recognition systems can permit the creation of photoregulated self-assembled macroscopic objects. Here we demonstrate that macroscopic gel assembly can be highly regulated through photoisomerization of an azobenzene moiety that interacts differently with two host molecules. A photoregulated gel assembly system is developed using polyacrylamide-based hydrogels functionalized with azobenzene (guest) or cyclodextrin (host) moieties. Reversible adhesion and dissociation of the host gel from the guest gel may be controlled by photoirradiation. The differential affinities of α-cyclodextrin or β-cyclodextrin for the trans-azobenzene and cis-azobenzene are employed in the construction of a photoswitchable gel assembly system. PMID:22215078

  15. Photoswitchable gel assembly based on molecular recognition

    PubMed Central

    Yamaguchi, Hiroyasu; Kobayashi, Yuichiro; Kobayashi, Ryosuke; Takashima, Yoshinori; Hashidzume, Akihito; Harada, Akira

    2012-01-01

    The formation of effective and precise linkages in bottom-up or top-down processes is important for the development of self-assembled materials. Self-assembly through molecular recognition events is a powerful tool for producing functionalized materials. Photoresponsive molecular recognition systems can permit the creation of photoregulated self-assembled macroscopic objects. Here we demonstrate that macroscopic gel assembly can be highly regulated through photoisomerization of an azobenzene moiety that interacts differently with two host molecules. A photoregulated gel assembly system is developed using polyacrylamide-based hydrogels functionalized with azobenzene (guest) or cyclodextrin (host) moieties. Reversible adhesion and dissociation of the host gel from the guest gel may be controlled by photoirradiation. The differential affinities of α-cyclodextrin or β-cyclodextrin for the trans-azobenzene and cis-azobenzene are employed in the construction of a photoswitchable gel assembly system. PMID:22215078

  16. Improving immobilized biocatalysts by gel phase polymerization

    SciTech Connect

    Kuu, W.Y.; Polack, J.A.

    1983-08-01

    A new method is presented for the treatment of gel-type supports, used for immobilizing microbial cells and enzymes, to obtain high mechanical strength. It is particularly useful for ethanol fermentation over gel beads containing immobilized viable cells, where the beads can be ruptured by gas production and the growth of cells within the gels. This method consists of treating agar or carrageenan gel with polyacrylamide to form a rigid support which retains the high catalytic activity characteristic of the untreated biocatalysts. The size and shape of the biocatalyst is unaffected by this treatment. The method involves the diffusion of acrylamide, N,N'-methylenebisacrylamide and BETA-dimethylaminopropionitrile (or N,N,N',N'-tetramethylethylenediamine) into the preformed biocatalyst beads followed by the addition of an initiator to cause polymerization within the beads. Treated gels have been used for the continuous fermentation of glucose to ethanol in a packed column for over two months.

  17. Generation of inkjet drop of particulate gel

    NASA Astrophysics Data System (ADS)

    Yoo, Hansol; Kim, Chongyoup

    2015-08-01

    The generation of inkjet drops of colloidal gels is studied experimentally. Particle suspensions are prepared by dispersing spherical polystyrene particles of 620 nm in the 1:1 mixture of deionized water and ethylene glycol. The gels are prepared by adding polyethylene oxide to the suspensions by inducing the depletion interaction between particles. It is demonstrated that inkjet drops can be generated by using the colloidal gels. It is found that the ligament extended from the inkjet nozzle is stabilized so that the drop can be generated without satellite droplets behind the main drop and the velocity of the gel drop is faster than that of the polymer solution at the same concentration. The gel drop generation characteristics are found to be sensitive to input voltage.

  18. Radiological properties of normoxic polymer gel dosimeters

    SciTech Connect

    Venning, A.J.; Nitschke, K.N.; Keall, P.J.; Baldock, C.

    2005-04-01

    The radiological properties of the normoxic polymer gel dosimeters MAGIC, MAGAS, and MAGAT [methacrylic and ascorbic acid in gelatin initiated by copper; methacrylic acid gelatine gel with ascorbic acid; and methacrylic acid gelatine and tetrakis (hydroxymethyl) phosphonium chloride, respectively] have been investigated. The radiological water equivalence was determined by comparing the polymer gel macroscopic photon and electron interaction cross sections over the energy range from 10 keV to 20 MeV and by Monte Carlo modeling of depth doses. Normoxic polymer gel dosimeters have a high gelatine and monomer concentration and therefore mass density (kg m{sup -3}) up to 3.8% higher than water. This results in differences between the cross-section ratios of the normoxic polymer gels and water of up to 3% for the attenuation, energy absorption, and collision stopping power coefficient ratios through the Compton dominant energy range. The mass cross-section ratios were within 2% of water except for the mass attenuation and energy absorption coefficients ratios, which showed differences with water of up to 6% for energies less than 100 keV. Monte Carlo modeling was undertaken for the polymer gel dosimeters to model the electron and photon transport resulting from a 6 MV photon beam. The absolute percentage differences between gel and water were within 1% and the relative percentage differences were within 3.5%. The results show that the MAGAT gel formulation is the most radiological water equivalent of the normoxic polymer gel dosimeters investigated due to its lower mass density measurement compared with MAGAS and MAGIC gels.

  19. Dewatering fine coal slurries by gel extraction

    SciTech Connect

    Gehrke, S.H.; Lyu, Lii-Hurng.

    1990-01-01

    A new technology called gel extraction has been evaluated to determine its economic viability in dewatering the fine and ultrafine coal slurries generated upon separation of sulfur and ash from clean coal during the physical coal cleaning process. Water must be removed from such slurries prior to transportation and combustion but the dewatering costs are substantial, especially for the fine particles below 28 mesh (0.6 mm). Gel extraction is a potential breakthrough in slurry dewatering technology. The goal of this project was to acquire the qualitative and quantitative data needed to estimate the potential of gel extraction for dewatering coal slurries. The specific objectives were to determine the maximum extents of dewatering (minimum surface moisture in the coal product), the clarity of the water removed (minimum solids content), the speed of the dewatering cycles, the service lifetime of the gels, and the factors which influence all of these. With the results obtained, an economic analysis of Ohio coal cleaning plant dewatering technologies was carried out. The polymer gel at the heart of this project, poly (N-isopropylacrylamide) (PNIPA), can swell several times its shrunken weight at 32[degrees]C by absorbing water at 25[degrees]C. In gel extraction, a shrunken NIPA gel is contacted with a slurry at ambient temperature or cooler; the gel swells by absorbing water from the slurry. The gel is then removed from the dewatered slurry and warmed above its critical temperature of 33[degrees]C, which returns it to the shrunken state by releasing the absorbed water. The facts that the gel is reusable and the process is simple and driven by low-grade energy (warm temperatures), and not inherently limited by particle size, made the process an attractive possible alternative to centrifugation, screening, filtration, etc. for slurry dewatering.

  20. T's and Blues. Specialized Information Service.

    ERIC Educational Resources Information Center

    Do It Now Foundation, Phoenix, AZ.

    This compilation of journal articles provides basic information on abuse of Talwin, a mild prescription painkiller (T's), and Pyribenzamine, a nonprescription antihistimine (Blues). These two drugs, taken in combination, produce an effect similar to that produced by heroin. Stories from "Drug Survival News,""Emergency Medicine," and "FDA Consumer"…

  1. Practices of Blue Ribbon Catholic Schools, 2001.

    ERIC Educational Resources Information Center

    Kealey, Robert J., Comp.

    For almost 20 years, the U.S. Department of Education has invited schools to seek the Blue Ribbon School Award. A large number of Catholic schools have received this award. For this publication, the Department of Elementary Schools Executive Committee requested principals of awarded schools to write a short article on an exemplary school program…

  2. Nanotubes based on monolayer blue phosphorus

    NASA Astrophysics Data System (ADS)

    Montes, E.; Schwingenschlögl, U.

    2016-07-01

    We demonstrate structural stability of monolayer zigzag and armchair blue phosphorus nanotubes by means of molecular dynamics simulations. The vibrational spectrum and electronic band structure are determined and analyzed as functions of the tube diameter and axial strain. The nanotubes are found to be semiconductors with a sensitive indirect band gap that allows flexible tuning.

  3. Blue nano titania made in diffusion flames.

    PubMed

    Teleki, Alexandra; Pratsinis, Sotiris E

    2009-05-21

    Blue titanium suboxide nanoparticles (including Magneli phases) were formed directly without any post-processing or addition of dopants by combustion of titanium-tetra-isopropoxide (TTIP) vapor at atmospheric pressure. Particle size, phase composition, rutile and anatase crystal sizes as well as the blue coloration were controlled by rapid quenching of the flame with a critical flow nozzle placed at various heights above the burner. The particles showed a broad absorption in the near-infrared region and retained their blue color upon storage in ambient atmosphere. A high concentration of paramagnetic Ti3+ centres was found in the substoichiometric particles by electron paramagnetic resonance (EPR) spectroscopy. Furthermore particles with controlled band gap energy from 3.2 to 3.6 eV were made by controlling the burner-nozzle-distance from 10 to 1 cm, respectively. The color robustness and extent of suboxidation could be further enhanced by co-oxidation of TTIP with hexamethyldisiloxane in the flame resulting in SiO2-coated titanium suboxide particles. The process is cost-effective and green while the particles produced can replace traditional blue colored, cobalt-containing pigments. PMID:19421486

  4. Blue-noise halftoning for hexagonal grids.

    PubMed

    Lau, Daniel L; Ulichney, Robert

    2006-05-01

    In this paper, we closely scrutinize the spatial and spectral properties of aperiodic halftoning schemes on rectangular and hexagonal sampling grids. Traditionally, hexagonal sampling grids have been shunned due to their inability to preserve the high-frequency components of blue-noise dither patterns at gray-levels near one-half, but as will be shown, only through the introduction of diagonal correlations between dots can even rectangular sampling grids preserve these frequencies. And by allowing the sampling grid to constrain the placement of dots, a particular algorithm may introduce visual artifacts just as disturbing as excess energy below the principal frequency. If, instead, the algorithm maintains radial symmetry by introducing a minimum degree of clustering, then that algorithm can maintain its grid defiance illusion fundamental to the spirit of the blue-noise model. As such, this paper shows that hexagonal grids are preferrable because they can support gray-levels near one-half with less required clustering of minority pixels and a higher principal frequency. Along with a thorough Fourier analysis of blue-noise dither patterns on both rectangular and hexagonal sampling grids, this paper also demonstrates the construction of a blue-noise dither array for hexagonal grids. PMID:16671307

  5. The blue rubber bleb [corrected] nevus syndrome.

    PubMed

    Feingold, Robert M

    2009-01-01

    The blue rubber bleb nevus syndrome, a rare condition characterized by lesions of the skin, gastrointestinal tract, and other parts of the body, can result in serious gastrointestinal bleeding and other adverse results and be challenging to manage. The clinical features and treatment of this rare disorder are reviewed here. PMID:19518008

  6. Geographical Study of American Blues Culture

    ERIC Educational Resources Information Center

    Strait, John B.

    2010-01-01

    Music is not often utilized in teaching geography, despite the fact that many scholars orient their research around analyzing both the historical and spatial dimensions of musical expression. This article reports on the use of a teaching module that utilizes blues culture as a lens to understand the geographical history of the United States. The…

  7. Blue whales respond to anthropogenic noise.

    PubMed

    Melcón, Mariana L; Cummins, Amanda J; Kerosky, Sara M; Roche, Lauren K; Wiggins, Sean M; Hildebrand, John A

    2012-01-01

    Anthropogenic noise may significantly impact exposed marine mammals. This work studied the vocalization response of endangered blue whales to anthropogenic noise sources in the mid-frequency range using passive acoustic monitoring in the Southern California Bight. Blue whales were less likely to produce calls when mid-frequency active sonar was present. This reduction was more pronounced when the sonar source was closer to the animal, at higher sound levels. The animals were equally likely to stop calling at any time of day, showing no diel pattern in their sensitivity to sonar. Conversely, the likelihood of whales emitting calls increased when ship sounds were nearby. Whales did not show a differential response to ship noise as a function of the time of the day either. These results demonstrate that anthropogenic noise, even at frequencies well above the blue whales' sound production range, has a strong probability of eliciting changes in vocal behavior. The long-term implications of disruption in call production to blue whale foraging and other behaviors are currently not well understood. PMID:22393434

  8. Blue LED irradiation to hydration of skin

    NASA Astrophysics Data System (ADS)

    Menezes, Priscila F. C.; Requena, Michelle B.; Lizarelli, Rosane F., Z.; Bagnato, Vanderlei S.

    2015-06-01

    Blue LED system irradiation shows many important properties on skin as: bacterial decontamination, degradation of endogenous skin chromophores and biostimulation. In this clinical study we prove that the blue light improves the skin hydration. In the literature none authors reports this biological property on skin. Then this study aims to discuss the role of blue light in the skin hydration. Twenty patients were selected to this study with age between 25-35 years old and phototype I, II and III. A defined area from forearm was pre determined (A = 4.0 cm2). The study was randomized in two treatment groups using one blue light device (power of 5.3mW and irradiance of 10.8mW/cm2). The first treatment group was irradiated with 3J/cm2 (277seconds) and the second with 6J/cm2 (555 seconds). The skin hydration evaluations were done using a corneometer. The measurements were collected in 7, 14, 21 and 30 days, during the treatment. Statistical test of ANOVA, Tukey and T-Student were applied considering 5% of significance. In conclusion, both doses were able to improve the skin hydration; however, 6J/cm2 has kept this hydration for 30 days.

  9. Quirks of dye nomenclature. 3. Trypan blue.

    PubMed

    Cooksey, C J

    2014-11-01

    Trypan blue is colorant from the 19(th) century that has an association with Africa as a chemotherapeutic agent against protozoan (Trypanosomal) infections, which cause sleeping sickness. The dye still is used for staining biopsies, living cells and organisms, and it also has been used as a colorant for textiles. PMID:24867494

  10. Heparin sensing: Blue-chip binding

    NASA Astrophysics Data System (ADS)

    Shriver, Zachary; Sasisekharan, Ram

    2013-08-01

    Heparin is an anionic polysaccharide that has tremendous clinical importance as an anticoagulant. Several dyes have been developed that can detect heparin, and the latest example -- named Mallard Blue -- has now been shown to have excellent sensing properties under biologically relevant conditions.

  11. A Discography of the Real Blues

    ERIC Educational Resources Information Center

    Tudor, Dean

    1972-01-01

    A short account of the rise and decline of the Blues and a discussion of the artists who performed it is followed by an annotated bibliography of periodicals, books, records and tapes related to this form of Black" music. (184 references) (NH)

  12. [The dangers of blue light: True story!].

    PubMed

    Renard, G; Leid, J

    2016-05-01

    The dangers of the blue light are the object of numerous publications, for both the scientific community and the general public. The new prolific development of light sources emitting potentially toxic blue light (415-455nm) ranges from LED (Light Emitting Diodes) lamps for interior lighting to television screens, computers, digital tablets and smartphones using OLED (Organic Light Emitting Diode) or AMOLED (Active-Matrix Organic Light Emitting Diode) technology. First we will review some technical terms and the main characteristics of light perceived by the human eye. Then we will discuss scientific proof of the toxicity of blue light to the eye, which may cause cataract or macular degeneration. Analysis of the light spectra of several light sources, from natural light to LED lamps, will allow us to specify even better the dangers related to each light source. LED lamps, whether used as components for interior lighting or screens, are of concern if they are used for extended viewing times and at short distance. While we can protect ourselves from natural blue light by wearing colored glasses which filter out, on both front and back surfaces, the toxic wavelengths, it is more difficult to protect oneself from LED lamps in internal lighting, the use of which should be restricted to "white warmth" lamps (2700K). As far as OLED or AMOLED screens are concerned, the only effective protection consists of using them occasionally and only for a short period of time. PMID:27039979

  13. Sol–gel composite material characteristics caused by different dielectric constant sol–gel phases

    NASA Astrophysics Data System (ADS)

    Kimoto, Keisuke; Matsumoto, Makoto; Kaneko, Tsukasa; Kobayashi, Makiko

    2016-07-01

    Ultrasonic transducers prepared by a sol–gel composite method have been investigated in the field of nondestructive testing (NDT). Sol–gel composite materials could be ideal piezoelectric materials for ultrasonic transducer applications in the NDT field, and a new sol–gel composite with desirable characteristics has been developed. Three kinds of sol–gel composite materials composed of different dielectric constant sol–gel phases, Pb(Zr,Ti)O3 (PZT), Bi4Ti3O12 (BiT), and BaTiO3 (BT), and the same piezoelectric powder phase, PbTiO3 (PT), were fabricated and their properties were compared quantitatively. As a result, the PT/BT, sol–gel composite with the highest dielectric constant sol–gel phase showed the highest d 33 and signal strength. In addition, only PT/BT was successfully poled by room-temperature corona poling with reasonable signal strength.

  14. Moisture Transport in Silica Gel Particle Beds: I. Theoretical Study

    SciTech Connect

    Pesaran, A. A.; Mills, A. F.

    1986-08-01

    Diffusion mechanisms of moisture within silica gel particles are investigated. It is found that for microporous silica gel surface diffusion is the dominant mechanism of moisture transport, while for macroporous silica gel both Knudsen and surface diffusion are important.

  15. Agonism and dominance in female blue monkeys.

    PubMed

    Klass, Keren; Cords, Marina

    2015-12-01

    Agonistic behavior features prominently in hypotheses that explain how social variation relates to ecological factors and phylogenetic constraints. Dominance systems vary along axes of despotism, tolerance, and nepotism, and comparative studies examine cross-species patterns in these classifications. To contribute to such studies, we present a comprehensive picture of agonistic behavior and dominance relationships in wild female blue monkeys (Cercopithecus mitis), an arboreal guenon, with data from 9 groups spanning 18 years. We assessed where blue monkeys fall along despotic, tolerant, and nepotistic spectra, how their dominance system compares to other primates, primarily cercopithecines, and whether their agonistic behavior matches socioecological model predictions. Blue monkeys showed low rates of mainly low-intensity agonism and little counter-aggression. Rates increased with rank and group size. Dominance asymmetry varied at different organizational levels, being more pronounced at the level of interactions than dyad or group. Hierarchies were quite stable, had moderate-to-high linearity and directional consistency and moderate steepness. There was clear maternal rank inheritance, but inconsistent adherence to Kawamura's rules. There was little between-group variation, although hierarchy metrics showed considerable variation across group-years. Overall, blue monkeys have moderately despotic, moderately tolerant, and nepotistic dominance hierarchies. They resemble other cercopithecines in having significantly linear and steep hierarchies with a generally stable, matriline-based structure, suggesting a phylogenetic basis to this aspect of their social system. Blue monkeys most closely match Sterck et al.'s [1997] Resident-Nepotistic-Tolerant dominance category, although they do not fully conform to predictions of any one socioecological model. Our results suggest that socioecological models might better predict variation within than across clades, thereby

  16. Improving immobilized biocatalysts by gel phase polymerization

    SciTech Connect

    Kuu, W.Y.; Polack, J.A.

    1983-08-01

    A new method is presented for the treatment of gel-type supports, used for immobilizing microbial cells and enzymes, to obtain high mechanical strength. It is particularly useful for ethanol fermentation over gel beads containing immobilized viable cells, where the beads can be ruptured by gas production and the growth of cells within the gels. This method consists of treating agar or carrageenan gel with polyacrylamide to form a rigid support which retains the high catalytic activity characteristic of the untreated biocatalysts. The size and shape of the biocatalyst is unaffected by this treatment. The method involves the diffusion of acrylamide, N,N'-methylenebisacrylamide and ..beta..-dimethylaminopropionitrile (or N,N,N',N'-tetramethylethylenediamine) into the preformed biocatalyst beads followed by the addition of an initiator to cause polymerization within the beads. Treated gels have been used for the continuous fermentation of glucose to ethanol in a packed column for over two months. During this operation, the gel beads maintained their rigidity, and the maximum productivity was as high as 50 gh/sup -1/ L/sup -1/ gel. There was no appreciable decay of cell activity.

  17. Sol-Gel Manufactured Energetic Materials

    DOEpatents

    Simpson, Randall L.; Lee, Ronald S.; Tillotson, Thomas M.; Hrubesh, Lawrence W.; Swansiger, Rosalind W.; Fox, Glenn A.

    2005-05-17

    Sol-gel chemistry is used for the preparation of energetic materials (explosives, propellants and pyrotechnics) with improved homogeneity, and/or which can be cast to near-net shape, and/or made into precision molding powders. The sol-gel method is a synthetic chemical process where reactive monomers are mixed into a solution, polymerization occurs leading to a highly cross-linked three dimensional solid network resulting in a gel. The energetic materials can be incorporated during the formation of the solution or during the gel stage of the process. The composition, pore, and primary particle sizes, gel time, surface areas, and density may be tailored and controlled by the solution chemistry. The gel is then dried using supercritical extraction to produce a highly porous low density aerogel or by controlled slow evaporation to produce a xerogel. Applying stress during the extraction phase can result in high density materials. Thus, the sol-gel method can be used for precision detonator explosive manufacturing as well as producing precision explosives, propellants, and pyrotechnics, along with high power composite energetic materials.

  18. Sol-gel manufactured energetic materials

    DOEpatents

    Simpson, Randall L.; Lee, Ronald S.; Tillotson, Thomas M.; Hrubesh, Lawrence W.; Swansiger, Rosalind W.; Fox, Glenn A.

    2003-12-23

    Sol-gel chemistry is used for the preparation of energetic materials (explosives, propellants and pyrotechnics) with improved homogeneity, and/or which can be cast to near-net shape, and/or made into precision molding powders. The sol-gel method is a synthetic chemical process where reactive monomers are mixed into a solution, polymerization occurs leading to a highly cross-linked three dimensional solid network resulting in a gel. The energetic materials can be incorporated during the formation of the solution or during the gel stage of the process. The composition, pore, and primary particle sizes, gel time, surface areas, and density may be tailored and controlled by the solution chemistry. The gel is then dried using supercritical extraction to produce a highly porous low density aerogel or by controlled slow evaporation to produce a xerogel. Applying stress during the extraction phase can result in high density materials. Thus, the sol-gel method can be used for precision detonator explosive manufacturing as well as producing precision explosives, propellants, and pyrotechnics, along with high power composite energetic materials.

  19. Electroacoustics of Particles Dispersed in Polymer Gel

    SciTech Connect

    Bhosale, Prasad S.; Chun, Jaehun; Berg, John C.

    2011-06-27

    This study examines the acoustic electrophoresis of particles dispersed in polymer hydrogels, with the particle size either less than or greater than the gel mesh size. When the particles are smaller than the gel mesh size, their acoustic vibration is resisted by only the background water medium, and the measured dynamic electrophoretic mobility, μd (obtained in terms of colloid vibration current, CVI), is the same as in water. For the case of particles larger than the gel mesh size, μd is decreased due to trapping, and the net decrease depends on the viscoelastic properties of the gel. The gel mesh size was varied by varying its crosslink density, the latter being characterized as the storage modulus, G’. The dependence of mobility on G’, for systems of a given particle size, and on particle size, for gels of a given G’, are investigated. The measured mobility remains constant as G’ is increased (i.e., mesh size is decreased) up to a value of approximately 300 Pa, beyond which it decreases. In the second set of measurements, the trapped particle size was increased in a gel medium of constant mesh size, with G’ approximately 100 Pa. In this case, the measured μd is found to be effectively constant over the particle size range studied (14-120 nm), i.e., it is independent of the degree of trapping as expressed by the ratio of the particle size to the mesh size.

  20. Developing the urban blue: Comparative health responses to blue and green urban open spaces in Germany.

    PubMed

    Völker, Sebastian; Kistemann, Thomas

    2015-09-01

    Recently, new perspectives upon healthy urban open spaces propose that open spaces can be regarded as urban green or blue spaces. However, there has so far been very little research into blue environments and their benefits for mental well-being. Our article focuses on the effects of water in cities, "urban blue" (as compared to "urban green"), on human health and well-being. To assess the mental well-being of visitors, we conducted qualitative semi-standardised interviews (n=113), asking which differences in well-being occur when visiting urban green and blue spaces in high-density areas of the inner city in Dusseldorf and Cologne, Germany. Although we found many similarities, some health-enhancing effects for users turned out to be prominent for urban blue in the four conceptual therapeutic landscape dimensions: experienced, symbolic, social and activity space. These effects include enhanced contemplation, emotional bonding, participation, and physical activity. The results suggest that urban blue as a health-promoting factor needs more detailed and accurate determination and examination of its general and local health-enhancing effects. PMID:25475835

  1. Evaluation of radiochromic gel dosimetry and polymer gel dosimetry in a clinical dose verification

    NASA Astrophysics Data System (ADS)

    Vandecasteele, Jan; De Deene, Yves

    2013-09-01

    A quantitative comparison of two full three-dimensional (3D) gel dosimetry techniques was assessed in a clinical setting: radiochromic gel dosimetry with an in-house developed optical laser CT scanner and polymer gel dosimetry with magnetic resonance imaging (MRI). To benchmark both gel dosimeters, they were exposed to a 6 MV photon beam and the depth dose was compared against a diamond detector measurement that served as golden standard. Both gel dosimeters were found accurate within 4% accuracy. In the 3D dose matrix of the radiochromic gel, hotspot dose deviations up to 8% were observed which are attributed to the fabrication procedure. The polymer gel readout was shown to be sensitive to B0 field and B1 field non-uniformities as well as temperature variations during scanning. The performance of the two gel dosimeters was also evaluated for a brain tumour IMRT treatment. Both gel measured dose distributions were compared against treatment planning system predicted dose maps which were validated independently with ion chamber measurements and portal dosimetry. In the radiochromic gel measurement, two sources of deviations could be identified. Firstly, the dose in a cluster of voxels near the edge of the phantom deviated from the planned dose. Secondly, the presence of dose hotspots in the order of 10% related to inhomogeneities in the gel limit the clinical acceptance of this dosimetry technique. Based on the results of the micelle gel dosimeter prototype presented here, chemical optimization will be subject of future work. Polymer gel dosimetry is capable of measuring the absolute dose in the whole 3D volume within 5% accuracy. A temperature stabilization technique is incorporated to increase the accuracy during short measurements, however keeping the temperature stable during long measurement times in both calibration phantoms and the volumetric phantom is more challenging. The sensitivity of MRI readout to minimal temperature fluctuations is demonstrated which

  2. Normoxic polymer gels: are they magic?

    NASA Astrophysics Data System (ADS)

    Amin, M. N.; Bonnett, D. E.; Horsfield, M. A.

    2004-01-01

    In the last few years there has been considerable interest in the use of polymer gels to measure complex dose distributions in radiotherapy. Despite considerable advantages they are still not widely used in clinical situations. This is due primarily to the difficulty in manufacture, particularly the need to exclude oxygen both from the gel and the manufacturing process, the limited number of suitable phantom materials and the need for easy access to an MRI facility. The purpose of this paper is to report on an investigation of the basic properties of MAGIC gels namely: linearity of response, effects of temperature and stability.

  3. Phantom for moving organ dosimetry with gel

    NASA Astrophysics Data System (ADS)

    Ravindran, Paul; Mahata, Anurupa; Suman Babu, Ebenezer

    2009-05-01

    The displacements caused by the cardiac and respiratory motions cause smearing of the dose distribution that defeats the purpose of high precision radiotherapy. A phontom that holds a gel cylinder and radiochromic film, was designed and developed to simulate the respiratory motion in the superior and inferior directions. The effect of lung movement on dose distribution was studied by exposing gel as well as a radiochromic film using the phantom. The results obtained with Gel was comparable to those obtained with the radiochromic films.

  4. 76 FR 35909 - Temporary Concession Contract for Blue Ridge Parkway

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-06-20

    ... National Park Service Temporary Concession Contract for Blue Ridge Parkway AGENCY: National Park Service, Interior. ACTION: Notice of proposed award of temporary concession contracts for Blue Ridge Parkway, NC/VA... Blue Ridge Parkway, North Carolina and Virginia, for a term not to exceed 3 years. The visitor...

  5. 77 FR 55895 - Permanent Closure of Cincinnati Blue Ash Airport

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-09-11

    ... Federal Aviation Administration Permanent Closure of Cincinnati Blue Ash Airport AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of permanent closure of Cincinnati Blue Ash Airport (ISZ). SUMMARY: The... Cincinnati advising that on August 29, 2012, it was permanently closing Cincinnati Blue Ash Airport...

  6. Is blue light good or bad for plants?

    PubMed

    Dougher, T A; Bugbee, B G

    1998-01-01

    Blue photons are energetically expensive so the most energy-efficient lamps contain the least blue light. Blue photons are not used efficiently in photosynthesis, but blue light has dramatic effects on plant development. We studied the growth and development of soybean, wheat, and lettuce plants under high-pressure sodium and metal halide lamps with yellow filters creating five fractions of blue light (0.5%, 3.5%, 6%, 1 8%, and 26% blue) at 500 micromoles m-2 s-1 and (< 0.1%, 1.7%, 6%, 12%, and 26%) at 200 mol m-2 s-1. The response was species dependent. Lettuce was highly sensitive to blue light fraction and had an optimum dry weight and leaf area at about 6% blue, but results were complicated by sensitivity to lamp type. Wheat and soybean were less sensitive to blue light, but dry mass and leaf area decreased steadily with increasing blue light. Blue light fraction significantly affected specific leaf area (SLA, m2 kg-1) and chlorophyll in lettuce, but had no significant effect on wheat and soybeans. The data suggest that lettuce benefits from some added blue light, but soybean and wheat may not. PMID:11541668

  7. 49 CFR 173.216 - Asbestos, blue, brown or white.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 2 2013-10-01 2013-10-01 false Asbestos, blue, brown or white. 173.216 Section... Class 7 § 173.216 Asbestos, blue, brown or white. (a) Asbestos, blue, brown or white, includes each of the following hydrated mineral silicates: chrysolite, crocidolite, amosite, anthophyllite...

  8. 49 CFR 173.216 - Asbestos, blue, brown or white.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 2 2012-10-01 2012-10-01 false Asbestos, blue, brown or white. 173.216 Section... Class 7 § 173.216 Asbestos, blue, brown or white. (a) Asbestos, blue, brown or white, includes each of the following hydrated mineral silicates: chrysolite, crocidolite, amosite, anthophyllite...

  9. 49 CFR 173.216 - Asbestos, blue, brown or white.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 2 2011-10-01 2011-10-01 false Asbestos, blue, brown or white. 173.216 Section... Class 7 § 173.216 Asbestos, blue, brown or white. (a) Asbestos, blue, brown or white, includes each of the following hydrated mineral silicates: chrysolite, crocidolite, amosite, anthophyllite...

  10. 49 CFR 173.216 - Asbestos, blue, brown or white.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Asbestos, blue, brown or white. 173.216 Section... Class 7 § 173.216 Asbestos, blue, brown or white. (a) Asbestos, blue, brown or white, includes each of the following hydrated mineral silicates: chrysolite, crocidolite, amosite, anthophyllite...

  11. 49 CFR 173.216 - Asbestos, blue, brown or white.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 2 2014-10-01 2014-10-01 false Asbestos, blue, brown or white. 173.216 Section... Class 7 § 173.216 Asbestos, blue, brown or white. (a) Asbestos, blue, brown or white, includes each of the following hydrated mineral silicates: chrysolite, crocidolite, amosite, anthophyllite...

  12. Isoelectric focusing of human parotid salivary proteins in hybrid carrier ampholyte-immobilized pH gradient polyacrylamide gels.

    PubMed

    Khoo, K S; Beeley, J A

    1990-06-01

    Isoelectric focusing of human salivary proteins with carrier ampholyte-isoelectric focusing systems requires prior desalting and concentration of samples, a procedure which is time-consuming and requires relatively large volumes of samples. By contrast, immobilized pH gradient gels are more tolerant to salt loads. Thus pretreatment of samples consists only of centrifugation prior to isoelectric focusing. If larger loads (greater than 50 micrograms) are required, the samples may be concentrated by lyophilization and reconstitution in a smaller volume of water or by dialysis against 30% w/v polyethylene glycol. Immobilized pH gradient polyacrylamide gels (incorporating a hybrid carrier ampholyte system) of two pH ranges (pH 4-9 and pH 3.5-5.0) have been used to separate the proteins in human parotid saliva. The effects of urea on focused patterns were studied; in pH 4-9 gels it gave improved resolution of protein bands, whereas in pH 3.5-5.0 gels it prevented protein precipitation. The salivary proteins were then visualized by staining with Coomassie Brilliant Blue G-250 or a silver procedure. Using the latter, 25-30 well-resolved bands were formed on a pH 4-9 gel loaded with 20 micrograms of proteins. The method offers considerable advantages compared with carrier ampholyte-isoelectric focusing. PMID:1697536

  13. Cell response to silica gels with varying mechanical properties

    NASA Astrophysics Data System (ADS)

    Lefebvre, Molly Ann

    Sol-gel encapsulation has a variety of applications in biotechnology and medicine: creating biosensors, biocatalysts, and bioartificial organs. However, encapsulated cell viability is a major challenge. Consequently, interactions between cells and their 3D microenvironment were studied through rheological, metabolic activity, and extraction studies to aid in the development of new gel protocols. The cells were encapsulated in variations of three silica sol-gels with varying stiffness. It was hypothesized that the cell viability and the amount of extracted cells would depend on gel stiffness. For two gels, there was no apparent correlation between the gel stiffness and the cell viability and extracted cell quantity. These gels did strongly depend on the varying gel ingredient, polyethylene glycol. The third gel appeared to follow the hypothesized correlation, but it was not statistically significant. Finally, one gel had a significantly longer period of cell viability and higher quantity of extracted cells than the other gels.

  14. Methylene blue mediated photodynamic therapy for resistant plaque psoriasis.

    PubMed

    Salah, Manal; Samy, Nevien; Fadel, Maha

    2009-01-01

    Topical treatment of resistant psoriatic plaque stage lesions may be difficult and the systemic therapies seem inappropriate. Therefore, a topical 0.1% methylene blue (MB) hydrogel was prepared and evaluated for percent drug content, drug uniformity, pH, rheological and organoleptic characters such as feel tackiness, grittiness sensation, and transparency in addition to release kinetics study in vitro. The efficiency of the photodynamic therapy (PDT) of MB photo-activated using 565 mW Light emitting diode (LED) 670 nm was evaluated in patients with resistant plaque psoriasis. The gel was evaluated in single blinded study. The patients were subjected to repeated sessions of irradiation, skin biopsies from each patient in the beginning and at the end of the sessions were taken for histopathological studies. Results showed the hydrogel was transparent nongritty and the drug uniformly dispersed with pH=7.2 and viscosity value=25.04 Pa. The drug content was found to be 99.4 +/- 0.15 %. Drug release was following zero order kinetics with rate constant K=0.348 +/- 0.01 and T(1/2) = 0.95 +/- 0.5 hours. Sixteen patients experienced complete clearance of their treated lesions. Skin appeared normal in color, texture, and pliability with no complications indicating the lack of skin sensitivity. Histopathological examinations showed nearly normal epidermis at the end of all sessions. The authors concluded that the prepared hydrogel was safe, stable, and very effective. The results are encouraging to accept MB as a photosensitizer for PDT and as a safe and effective method for treatment of selected cases of resistant localized psoriasis PMID:19180895

  15. Blue emission of Eu2+-doped translucent alumina

    DOE PAGESBeta

    Yang, Yan; Zhang, Lihua; Kisslinger, Kim; Wei, Hua; Melcher, Charles L.; Wu, Yiquan

    2015-08-21

    Inorganic scintillators are very important in medical and industrial measuring systems in the detection and measurement of ionizing radiation. In addition to Ce3+, a widely used dopant ion in oxide scintillators, divalent Europium (Eu2+) has shown promise as a high-luminescence, fast-response luminescence center useful in the detection of ionizing radiation. In this research, aluminum oxide (Al2O3) was studied as a host material for the divalent europium ion. Polycrystalline samples of Eu2+-doped translucent Al2O3 were fabricated, and room temperature luminescence behavior was observed. Al2O3 ceramics doped with 0.1 at% Eu2+ were fabricated with a relative density of 99.75% theoretical density andmore » in-line transmittance of 22% at a wavelength of 800 nm. The ceramics were processed by a gel-casting method, followed by sintering under high vacuum. The gelling agent, a copolymer of isobutylene and maleic anhydride, is marketed under the commercial name ISOBAM, and has the advantage of simultaneously acting as both a gelling agent and as a dispersant. The microstructure and composition of the vacuum-sintered Eu2+:Al2O3 were characterized by Scanning Electric Microscopy (SEM), Transmission Electron Microscopy (TEM), and Energy-dispersive X-ray spectroscopy (EDS). The phase composition was determined by X-ray diffraction measurements (XRD) combined with Rietveld analysis. The photoluminescence behavior of the Eu2+:Al2O3 was characterized using UV light as the excitation source, which emitted blue emission at 440 nm. The radio-luminescence of Eu2+:Al2O3 was investigated by illumination with X-ray radiation, showing three emission bands at 376 nm, 575 nm and 698 nm. Furthermore, multiple level traps at different depths were detected in the Eu2+:Al2O3 by employing thermoluminescence measurements.« less

  16. Sensitive colorimetric cytotoxicity measurement using alarmar blue.

    PubMed

    Page, B; Page, M

    1995-01-01

    Cytotoxicity testing of anticancer drugs requires techniques which are sensitive, reproductible and applicable to large scale testing using automated instruments. End point staining of cells or viability stains are reliable but they are often not sensitive enough or not suitable for automation. We have already described a fluorometric cytotoxicity assay using a non fluorescent substrate, Alarmar Blue, which upon reduction in living cells, yields a fluorescent product. This assay is sensitive and highly reproductible but it is limited since automated fluorescent plate readers are not found frequently in laboratories. The conditions are now described for using Alamar Blue as a substrate in a colorimetric cytotoxicity assay. This new economical assay could be used with advantage for large scale screening of cytotoxic agents in microtitration plates. PMID:21597689

  17. Phycobilisomes in Blue-Green Algae

    PubMed Central

    Wildman, Ruth B.; Bowen, C. C.

    1974-01-01

    Fifteen species of freshwater blue-green algae, including unicellular, filamentous, and colonial forms, were subjected to a variety of fixatives, fixation conditions, and stains for comparison of the preservation of phycobilisomes. Absorption spectra of the corresponding in vivo and released photosynthetic pigments, in 10 of the species that were maintained in culture, demonstrated the presence of phycocyanin in all 10 species and phycoerythrin in only 2 of them. Spectroscope and electron microscope evidence was obtained for localization of phycobiliproteins in phycobilisomes of Nostoc muscorum. Phycobilisomes were observed in all species examined in situ, strenghening the hypothesis that phycobilisomes are common to all phycobiliprotein-containing photosynthetic blue-green algae. Images PMID:4204443

  18. Influence of gel dimensions on resolution and sample throughput on two-dimensional gels.

    PubMed

    Lee, KiBeom; Pi, KyungBae; Lee, Hong-Gu

    2008-04-01

    To achieve high throughput and economical format of 2-D PAGE, comparison between gel size and resolution was conducted on human breast carcinoma cell line (MCF-7/AZ) proteins. SDS gel length showed a weaker influence of separation length on resolution in the second dimension, and there was little benefit of separation distances greater than 15 to 19 cm. IPG strip separation distances were very important with dramatic increase in resolution of longer gels compared with smaller gels, and maximal resolution was obtained using 18- and 24-cm IPG strips. Loading optimal amount of proteins on 2-D gels can also increase the number of detected spots. Therefore, taken together, compromise 2-D gels are crucial for higher capacity and higher throughput. PMID:18457572

  19. Manual control of catalytic reactions: Reactions by an apoenzyme gel and a cofactor gel

    PubMed Central

    Kobayashi, Yuichiro; Takashima, Yoshinori; Hashidzume, Akihito; Yamaguchi, Hiroyasu; Harada, Akira

    2015-01-01

    Enzymes play a vital role in catalysing almost all chemical reactions that occur in biological systems. Some enzymes must form complexes with non-protein molecules called cofactors to express catalytic activities. Although the control of catalytic reactions via apoenzyme–cofactor complexes has attracted significant attention, the reports have been limited to the microscale. Here, we report a system to express catalytic activity by adhesion of an apoenzyme gel and a cofactor gel. The apoenzyme and cofactor gels act as catalysts when they form a gel assembly, but they lose catalytic ability upon manual dissociation. We successfully construct a system with switchable catalytic activity via adhesion and separation of the apoenzyme gel with the cofactor gel. We expect that this methodology can be applied to regulate the functional activities of enzymes that bear cofactors in their active sites, such as the oxygen transport of haemoglobin or myoglobin and the electron transport of cytochromes. PMID:26537172

  20. Manual control of catalytic reactions: Reactions by an apoenzyme gel and a cofactor gel

    NASA Astrophysics Data System (ADS)

    Kobayashi, Yuichiro; Takashima, Yoshinori; Hashidzume, Akihito; Yamaguchi, Hiroyasu; Harada, Akira

    2015-11-01

    Enzymes play a vital role in catalysing almost all chemical reactions that occur in biological systems. Some enzymes must form complexes with non-protein molecules called cofactors to express catalytic activities. Although the control of catalytic reactions via apoenzyme-cofactor complexes has attracted significant attention, the reports have been limited to the microscale. Here, we report a system to express catalytic activity by adhesion of an apoenzyme gel and a cofactor gel. The apoenzyme and cofactor gels act as catalysts when they form a gel assembly, but they lose catalytic ability upon manual dissociation. We successfully construct a system with switchable catalytic activity via adhesion and separation of the apoenzyme gel with the cofactor gel. We expect that this methodology can be applied to regulate the functional activities of enzymes that bear cofactors in their active sites, such as the oxygen transport of haemoglobin or myoglobin and the electron transport of cytochromes.

  1. Novel tannin-based adsorbent in removing cationic dye (Methylene Blue) from aqueous solution. Kinetics and equilibrium studies.

    PubMed

    Sánchez-Martín, J; González-Velasco, M; Beltrán-Heredia, J; Gragera-Carvajal, J; Salguero-Fernández, J

    2010-02-15

    Natural tannin-based adsorbent has been prepared on the basis of the gelification of Quebracho bark extract. The resulting product, Quebracho Tannin Gel (QTG) was tested as cationic dye adsorbent with Methylene Blue (MB). Kinetics of adsorption process were studied out and a period of 15 days was determined for reaching equilibrium. The influences of pH and temperature were evaluated. As pH or temperature raise q capacity of QTG increases. Theoretical modelization of dye-QTG adsorption was carried out by multiparametric adjustment according to Langmuir's hypothesis. Values of the k(l1), k(l2) and activation energies were calculated. PMID:19782466

  2. Sol-gel antireflective coating on plastics

    DOEpatents

    Ashley, C.S.; Reed, S.T.

    1988-01-26

    An antireflection film made from reliquified sol-gel hydrolyzation, condensation polymeric reaction product of a silicon, alkoxides and/or metal alkoxides, or mixtures thereof. The film is particularly useful for coating plastics.

  3. Magnetic Hyperthermia in ferrofluid-gel composites

    NASA Astrophysics Data System (ADS)

    Nemala, Humeshkar; Wadehra, Anshu; Dixit, Ambesh; Regmi, Rajesh; Vaishnava, Prem; Lawes, Gavin; Naik, Ratna

    2012-02-01

    Magnetic hyperthermia is the generation of heat by an external magnetic field using superparamagnetic nanoparticles. However, there are still questions concerning magnetic hyperthermia in tissue; in particular the confinement of the nanoparticles at mesoscopic scales. We used Agarose and Alginate gels as models for human tissue and embedded magnetic nanoparticles in them. We report the synthesis and characterization of dextran coated iron oxide (Fe3O4) nanoparticles. Characterization of these nanoparticles was done using X-ray diffraction, transmission electron microscopy, magnetometry, and hyperthermia measurements. Temperature dependent susceptibility measurements reveal a sharp anomaly in the ferrofluid sample at the freezing temperature. This is conspicuously absent in the ferrofluid-gel composites. Heat generation studies on these superparamagnetic gel-composites revealed a larger heat production in the ferrofluids(˜4W/g) as compared to the gels(˜1W/g), which we attribute to a reduction in Brownian relaxation for the nanoparticles embedded in Agarose and Alginate.

  4. Turbidimetric studies of Limulus coagulin gel formation.

    PubMed Central

    Moody, T P; Donovan, M A; Laue, T M

    1996-01-01

    The turbidity during trypsin-induced coagulin gel formation was studied over a range of wavelengths. The range of wavelengths used (686-326 nm) also made it possible to investigate the dependence of turbidity on wavelength (the wavelength exponent). Using the results from that work, and structural information on coagulin and the coagulin gel from other studies, a model gel-forming system was designed that consists of species for which the turbidity can be calculated relatively simply. These species include small particles (small in all dimensions relative to the wavelength of incident light); long rods and long random coils (particles that are large in just one dimension relative to the wavelength of incident light); and reflective regions (aggregated material that is large in more than one dimension relative to the wavelength of incident light). The turbidimetric characteristics of the real coagulin gel-forming system are compared with those of the model system. PMID:8889175

  5. Elastocapillary Deformations and Fracture of Soft Gels

    NASA Astrophysics Data System (ADS)

    Daniels, Karen; Grzelka, Marion; Bostwick, Joshua

    When a droplet is placed on the surface of a soft gel, the surface deforms by an amount proportional to the elastocapillary length calculated from the ratio of surface tension and elastic modulus. For sufficiently large deformations, the gel can fracture due to the forces generated under the liquid-gel contact line. We observe that a starburst of channel fractures forms at the surface of the gel, driven by fluid propagating away from the central droplet. To understand the initiation of these cracks, we model the substrate as an incompressible, linear-elastic solid and quantify the elastic response. This provides quantitative agreement with experimental measurements of the number of fracture arms as a function of material properties and geometric parameters. In addition, we find that the initiation process is thermally-activated, with delay time that decreases as a function of the elastocapillary length.

  6. Sol-gel antireflective coating on plastics

    DOEpatents

    Ashley, Carol S.; Reed, Scott T.

    1990-01-01

    An antireflection film made from a reliquified sol-gel hydrolyzation, condensation polymeric reaction product of a silicon, alkoxides and/or metal alkoxides, or mixtures thereof. The film is particularly useful for coating plastics.

  7. Procedure to prepare transparent silica gels

    NASA Technical Reports Server (NTRS)

    Barber, Patrick G. (Inventor); Simpson, Norman R. (Inventor)

    1987-01-01

    This invention relates to the production of silica gels and in particular to a process for the preparation of silica gels which can be used as a crystal growth medium that simulates the convectionless environment of space to produce structurally perfect crystals. Modern utilizations of substances in electronics, such as radio transmitters and high frequency microphones, often require single crystals with controlled purity and structural perfection. The near convectionless environment of silica gel suppresses nucleation, thereby reducing the competitive nature of crystal growth. This competition limits the size and perfection of the crystal; and it is obviously desirable to suppress nucleation until, ideally, only one crystal grows in a predetermined location. A silica gel is not a completely convectionless environment like outer space, but is the closest known environment to that of outer space that can be created on Earth.

  8. Sol-gel deposited electrochromic coatings

    SciTech Connect

    Ozer, N.; Lampert, C.M.

    1995-06-01

    Electrochromic devices have increasing application in display devices, switchable mirrors and smart windows. A variety of vacuum deposition technologies have been used to make electrochromic devices. The sol- gel process offers an alternative approach to the synthesis of optical quality and low cost electrochromic device layers. This study summarizes the developments in sol-gel deposited electrochromic films. The sol-gel process involves the formation of oxide networks upon hydrolysis-condensation of alkoxide precursors. In this study we cover the sol-gel deposited oxides of WO[sub 3], V[sub 2]O[sub 5], TiO[sub 2], Nb[sub 2]O[sub 5], and NiO[sub x].

  9. K-Basin gel formation studies

    SciTech Connect

    Beck, M.A.

    1998-07-23

    A key part of the proposed waste treatment for K Basin sludge is the elimination of reactive uranium metal by dissolution in nitric acid (Fkirnent, 1998). It has been found (Delegard, 1998a) that upon nitric acid dissolution of the sludge, a gel sometimes forms. Gels are known to sometimes impair solid/liquid separation and/or material transfer. The purpose of the work reported here is to determine the cause(s) of the gel formation and to determine operating parameters for the sludge dissolution that avoid formation of gel. This work and related work were planned in (Fkunent, 1998), (Jewett, 1998) and (Beck, 1998a). This report describes the results of the tests in (Beck, 1998a) with non-radioactive surrogates.

  10. Advanced gel propulsion controls for kill vehicles

    NASA Astrophysics Data System (ADS)

    Yasuhara, W. K.; Olson, A.; Finato, S.

    1993-06-01

    A gel propulsion control concept for tactical applications is reviewed, and the status of the individual component technologies currently under development at the Aerojet Propulsion Division is discussed. It is concluded that a gel propellant Divert and Attitude Control Subsystem (DACS) provides a safe, insensitive munitions compliant alternative to current liquid Theater Missile Defense (TMD) DACS approaches. The gel kill vehicle (KV) control system packages a total impulse typical of a tactical weapon interceptor for the ground- or sea-based TMD systems. High density packaging makes it possible to increase firepower and to eliminate long-term high pressure gas storage associated with bipropellant systems. The integrated control subsystem technologies encompass solid propellant gas generators, insulated composite overwrapped propellant tanks, lightweight endoatmospheric thrusters, and insensitive munition gel propellants, which meet the requirements of a deployable, operationally safe KV.

  11. Sample collection system for gel electrophoresis

    SciTech Connect

    Olivares, Jose A.; Stark, Peter C.; Dunbar, John M.; Hill, Karen K.; Kuske, Cheryl R.; Roybal, Gustavo

    2004-09-21

    An automatic sample collection system for use with an electrophoretic slab gel system is presented. The collection system can be used with a slab gel have one or more lanes. A detector is used to detect particle bands on the slab gel within a detection zone. Such detectors may use a laser to excite fluorescently labeled particles. The fluorescent light emitted from the excited particles is transmitted to low-level light detection electronics. Upon the detection of a particle of interest within the detection zone, a syringe pump is activated, sending a stream of buffer solution across the lane of the slab gel. The buffer solution collects the sample of interest and carries it through a collection port into a sample collection vial.

  12. Gel pad application for automated breast sonography.

    PubMed

    Kim, Yun Ju; Kim, Sung Hun; Jeh, Su Kyung; Choi, Jae Jeong; Kang, Bong Joo; Song, Byung Joo

    2015-04-01

    The purpose of this study was to describe the technical aspects of gel pad application for automated breast sonography and to show its effects on pain relief, scan coverage, and image quality. Twenty patients underwent 2 sets of automated breast sonography with and without gel pad application and were then asked to provide feedback on the examination-related pain. Scan coverage and image quality were compared quantitatively and qualitatively. The degree of pain was significantly decreased after gel pad application (P < .0001). The scan coverage was expanded particularly at the mid-portion of the breast. Image quality was satisfactory without significant differences between the sets. Gel pad application for automated breast sonography is easy and provides significant pain relief. The scan coverage was expanded, while the image quality was maintained. PMID:25792588

  13. Experiencing Blues at the Crossroads: A Place-Based Method for Teaching the Geography of Blues Culture

    ERIC Educational Resources Information Center

    Strait, John

    2012-01-01

    This article offers a pedagogical module that explores the geography of blues culture across the Mississippi Delta. By focusing on blues culture, rather than simply blues music itself, this project provides a forum for understanding the broader geographical conditions from which this musical form emerged. This module utilizes place-based…

  14. Eta Carinae and Other Luminous Blue Variables

    NASA Technical Reports Server (NTRS)

    Corcoran, M. F.

    2006-01-01

    Luminous Blue Variables (LBVs) are believed to be evolved, extremely massive stars close to the Eddington Limit and hence prone to bouts of large-scale, unstable mass loss. I discuss current understanding of the evolutionary state of these objects, the role duplicity may play and known physical characteristics of these stars using the X-ray luminous LBVs Eta Carinae and HD 5980 as test cases.

  15. Combined Cellular Blue Nevus and Trichoepithelioma

    PubMed Central

    Martin, Richard; Emanuel, Patrick

    2013-01-01

    Biphasic lesions composed of melanocytic and epithelial components are not uncommon. Combined trichoepithelioma and cellular blue naevus is a rare lesion that may mimic melanoma clinically. The authors describe what they believe to be the fourth case of this rare tumor and review the literature. Recent descriptions of malignant basomelanocytic tumors have raised interesting questions surrounding the pathogenesis of lesions composed of these cell lineages. PMID:24003350

  16. Luminescence conversion of blue light emitting diodes

    NASA Astrophysics Data System (ADS)

    Schlotter, P.; Schmidt, R.; Schneider, J.

    Using blue-emitting GaN/6HSiC chips as primary light sources, we have fabricated green, yellow, red and white emitting LEDs. The generation of mixed colors, as turquoise and magenta is also demonstrated. The underlying physical principle is that of luminescence down-conversion (Stokes shift), as typical for organic luminescent dye molecules. A white emitting LED, using an inorganic converter, Y3Al5O12:Ce3+( ), has also been realized.

  17. Rheological Characterization of Ethanolamine Gel Propellants

    NASA Astrophysics Data System (ADS)

    V. S Jyoti, Botchu; Baek, Seung Wook

    2016-07-01

    Ethanolamine is considered to be an environmentally friendly propellant system because it has low toxicity and is noncarcinogenic in nature. In this article, efforts are made to formulate and prepare ethanolamine gel systems, using pure agarose and hybrids of paired gelling agents (agarose + polyvinylpyrrolidine (PVP), agarose + SiO2, and PVP + SiO2), that exhibit a measurable yield stress, thixotropic behavior under shear rate ranges of 1-1,000 s-1 and a viscoelastic nature. To achieve these goals, multiple rheological experiments (including flow and dynamic studies) are performed. In this article, results are presented from experiments measuring the apparent viscosity, yield stress, thixotropy, dynamic strain, frequency sweep, and tan δ behaviors, as well as the effects of the test temperature, in the gel systems. The results show that the formulated ethanolamine gels are thixotropic in nature with yield stress between 30 and 60 Pa. The apparent viscosity of the gel decreases as the test temperature increases, and the apparent activation energy is the lowest for the ethanolamine-(PVP + SiO2) gel system. The dynamic rheology study shows that the type of gellant, choice of hybrid gelling materials and their concentration, applied frequencies, and strain all vitally affect the viscoelastic properties of the ethanolamine gel systems. In the frequency sweep experiment, the ethanolamine gels to which agarose, agarose + PVP, and agarose + SiO2 were added behave like linear frequency-dependent viscoelastic liquids, whereas the ethanolamine gel to which PVP + SiO2 was added behaves like a nearly frequency-independent viscoelastic solid. The variation in the tan δ of these gelled propellants as a function of frequency is also discussed.

  18. Annular gel reactor for chemical pattern formation

    DOEpatents

    Nosticzius, Zoltan; Horsthemke, Werner; McCormick, William D.; Swinney, Harry L.; Tam, Wing Y.

    1990-01-01

    The present invention is directed to an annular gel reactor suitable for the production and observation of spatiotemporal patterns created during a chemical reaction. The apparatus comprises a vessel having at least a first and second chamber separated one from the other by an annular polymer gel layer (or other fine porous medium) which is inert to the materials to be reacted but capable of allowing diffusion of the chemicals into it.

  19. Sol-Gels for Optical Sensors

    NASA Astrophysics Data System (ADS)

    Podbielska, Halina; Ulatowska-Jarża, Agnieszka; Müller, Gerhard; Eichler, Hans J.

    Sol-gel process allows for formation of glassy and ceramics materials in temperatures much lower than offered by conventional melting techniques. The first paper on sol-gels was published over 150 years ago by Ebelmen, however, the rapid development of this technology and applications occurred in the last few years. There is a broad range of possible applications of solgel derived materials, what marked this technology as one of the most promising fields of contemporary material sciences

  20. Red, Green, and Blue Astro-combs

    NASA Astrophysics Data System (ADS)

    Phillips, David; Glenday, Alex; Li, Chih-Hao; Korzennik, Sylvain; Noah Chang, Guoqing; Chen, Li-Jin; Benedick, Andrew; Kaertner, Franz; Sasselov, Dimitar; Szentgyorgyi, Andrew; Walsworth, Ronald

    2011-06-01

    Searches for extrasolar planets using the periodic Doppler shift of stellar lines are approaching Earth-like planet sensitivity. Astro-combs, a combination of an octave spanning femtosecond laser and a mode-filtering cavity provide a likely route to increased calibration precision and accuracy. We present results from three astro-combs operating in the red/near-IR, green and blue spectral ranges. Light from a 1-GHz, octave-spanning Ti:Sapphire laser is filtered by a Fabry-Perot Cavity (FPC) constructed from Doubly-Chirped Mirrors to produce a red astro-comb with 100 nm of optical bandwidth. This astro-comb has calibrated an astrophysical spectrograph at the 1 m/s level. In the blue astro-comb, Ti:Sapphire comb light, doubled in a BBO crystal is filtered to 50 GHz mode spacing with an FPC. The blue astro-comb has performed 50 cm/s calibrations. In the ``green'' astro-comb, light from the 1 GHz Ti:Sapphire comb laser is broadened in a photonic crystal fiber optimized to produce light in the green. This 1-GHz spaced green light is then filtered to roughly 40 GHz via an FPC with zero group delay dispersion mirrors, providing approximately 50 nm of astro-comb light centered near 550 nm.

  1. QCD and the BlueGene

    SciTech Connect

    Vranas, P

    2007-06-18

    Quantum Chromodynamics is the theory of nuclear and sub-nuclear physics. It is a celebrated theory and one of its inventors, F. Wilczek, has termed it as '... our most perfect physical theory'. Part of this is related to the fact that QCD can be numerically simulated from first principles using the methods of lattice gauge theory. The computational demands of QCD are enormous and have not only played a role in the history of supercomputers but are also helping define their future. Here I will discuss the intimate relation of QCD and massively parallel supercomputers with focus on the Blue Gene supercomputer and QCD thermodynamics. I will present results on the performance of QCD on the Blue Gene as well as physics simulation results of QCD at temperatures high enough that sub-nuclear matter transitions to a plasma state of elementary particles, the quark gluon plasma. This state of matter is thought to have existed at around 10 microseconds after the big bang. Current heavy ion experiments are in the quest of reproducing it for the first time since then. And numerical simulations of QCD on the Blue Gene systems are calculating the theoretical values of fundamental parameters so that comparisons of experiment and theory can be made.

  2. Blue Rose perimeter defense and security system

    NASA Astrophysics Data System (ADS)

    Blackmon, F.; Pollock, J.

    2006-05-01

    An in-ground perimeter security system has been developed by the Naval Undersea Warfare Center Division Newport based upon fiber optic sensor technology. The system, called Blue Rose, exploits the physical phenomenon of Rayleigh optical scattering, which occurs naturally in optical fibers used traditionally for Optical Time Domain Reflectometry techniques to detect sound and vibration transmitted by intruders such as people walking or running and moving vehicles near the sensor. The actual sensor is a single-mode optical fiber with an elastomeric coating that is buried in the ground. A long coherence length laser is used to transmit encoded light down the fiber. Minute changes in the fiber in response to the intrusion produce phase changes to the returning backscattered light signal. The return light signal contains both the actual intrusion sound and the location information of where along the fiber the intrusion has occurred. A digital, in-ground, Blue Rose system has been built and is now operational at NUWC. Due to the low cost of the optical fiber sensor and unique benefits of the system, the Blue Rose system provides an advantage in long perimeter or border security applications and also reduces security manning requirements and therefore overall cost for security.

  3. Automated detection of Antarctic blue whale calls.

    PubMed

    Socheleau, Francois-Xavier; Leroy, Emmanuelle; Pecci, Andres Carvallo; Samaran, Flore; Bonnel, Julien; Royer, Jean-Yves

    2015-11-01

    This paper addresses the problem of automated detection of Z-calls emitted by Antarctic blue whales (B. m. intermedia). The proposed solution is based on a subspace detector of sigmoidal-frequency signals with unknown time-varying amplitude. This detection strategy takes into account frequency variations of blue whale calls as well as the presence of other transient sounds that can interfere with Z-calls (such as airguns or other whale calls). The proposed method has been tested on more than 105 h of acoustic data containing about 2200 Z-calls (as found by an experienced human operator). This method is shown to have a correct-detection rate of up to more than 15% better than the extensible bioacoustic tool package, a spectrogram-based correlation detector commonly used to study blue whales. Because the proposed method relies on subspace detection, it does not suffer from some drawbacks of correlation-based detectors. In particular, it does not require the choice of an a priori fixed and subjective template. The analytic expression of the detection performance is also derived, which provides crucial information for higher level analyses such as animal density estimation from acoustic data. Finally, the detection threshold automatically adapts to the soundscape in order not to violate a user-specified false alarm rate. PMID:26627784

  4. The Blue Comet: A Railroad's Astronomical Heritage

    NASA Astrophysics Data System (ADS)

    Rumstay, Kenneth S.

    2009-01-01

    Between 1929 February 21 and 1941 September 27, the Central New Jersey Railroad operated a luxury passenger train between Jersey City and Atlantic City. Named The Blue Comet, the locomotive, tender, and coaches sported a unique royal blue paint scheme designed to evoke images of celestial bodies speeding through space. Inside each car were etched window panes and lampshades featuring stars and comets. And each coach sported the name of a famous comet on its side; these comets were of course named for their discoverers. Some of the astronomers honored in this unique fashion remain famous to this day, or at least their comets do. The names D'Arrest, Barnard, Encke, Faye, Giacobini, Halley, Olbers, Temple, Tuttle, and Westphal are familiar ones. But Biela, Brorsen, deVico, Spitaler, and Winnecke have now largely faded into obscurity; their stories are recounted here. Although more than sixty years have elapsed since its last run, The Blue Comet, perhaps the most famous passenger train in American history, lives on in the memories of millions of passengers and railfans. This famous train returned to the attention of millions of television viewers on the evening of 2007 June 3, in an episode of the HBO series The Sopranos. This work was supported by a faculty development grant from Valdosta State University.

  5. The effect of graphene on liquid-crystalline blue phases

    NASA Astrophysics Data System (ADS)

    Lavrič, M.; Tzitzios, V.; Kralj, S.; Cordoyiannis, G.; Lelidis, I.; Nounesis, G.; Georgakilas, V.; Amenitsch, H.; Zidanšek, A.; Kutnjak, Z.

    2013-09-01

    The stabilization of liquid-crystalline blue phases is recently attracting considerable interest because of the envisioned applications in fast optical displays and tunable photonic crystals. We report on the effect of surface-functionalized graphene nanosheets on the blue phase range of a chiral liquid crystal. Calorimetric and optical measurements, reproducible on heating and cooling, demonstrate that the resulting soft nanocomposite exhibits an increased blue phase temperature stability range for a minute concentration of dispersed graphene. The impact is stronger on the ordered, cubic structured blue phase I. These findings suggest that anisotropic nanoparticles may be of great usefulness for stabilizing blue phases.

  6. Cavitation of a Physically Associating Gel

    NASA Astrophysics Data System (ADS)

    Mishra, Satish; Kundu, Santanu

    Self-assembly of block copolymers in selective solvents form ordered structures such as micelles, vesicles, and physically crosslinked gels due to difference in their interaction with solvents. These gels have wide range of applications in tissue engineering, food science and biomedical field due to their tunable properties and responsiveness with changing environmental conditions. Pressurization of a defect inside a physically associating gel can lead to elastic instability (cavitation) leading to failure of the gel. The failure behavior involves dissociation of physical networks. A thermoreversible, physically associating gel with different volume fractions of a triblock copolymer, poly (methyl methacrylate)-poly (n-butyl acrylate)-poly (methyl methacrylate) [PMMA-PnBA-PMMA] in 2-ethyl 1-hexanol, a midblock selective solvent, is considered here. Mechanical properties were investigated using shear rheology and cavitation experiments. The experimental data is fitted with a constitutive model that captures the stiffening behavior followed by softening behavior of a physical gel. Finite element analysis has been performed on cavitation rheology geometry to capture the failure behavior and to calculate energy release rate during cavitation experiments.

  7. Treatment of osteochondral injuries with platelet gel

    PubMed Central

    Danieli, Marcus Vinicius; da Rosa Pereira, Hamilton; de Sá Carneiro, Carlos Augusto; Felisbino, Sérgio Luiz; Deffune, Elenice

    2014-01-01

    OBJECTIVES: Treatments for injured articular cartilage have not advanced to the point that efficient regeneration is possible. However, there has been an increase in the use of platelet-rich plasma for the treatment of several orthopedic disorders, including chondral injuries. Our hypothesis is that the treatment of chondral injuries with platelet gel results in higher-quality repair tissue after 180 days compared with chondral injuries not treated with gel. METHODS: A controlled experimental laboratory study was performed on 30 male rabbits to evaluate osteochondral injury repair after treatment with or without platelet gel. Osteochondral injuries were surgically induced in both knees of each rabbit at the medial femoral condyle. The left knee injury was filled with the platelet gel, and the right knee was not treated. Microscopic analysis of both knee samples was performed after 180 days using a histological grading scale. RESULTS: The only histological evaluation criterion that was not significantly different between treatments was metachromasia. The group that was treated with platelet gel exhibited superior results in all other criteria (cell morphology, surface regularity, chondral thickness and repair tissue integration) and in the total score. CONCLUSION: The repair tissue was histologically superior after 180 days in the study group treated with platelet gel compared with the group of untreated injuries. PMID:25518022

  8. Basic investigations on LCV micelle gel

    NASA Astrophysics Data System (ADS)

    Ebenezer, S. B.; Rafic, M. K.; Ravindran, P. B.

    2013-06-01

    The aim of this study was to investigate the feasibility of using Leuco Crystal Violet (LCV) based micelle gel dosimeter as a quality assurance tool in radiotherapy applications. Basic properties such as absorption coefficient and diffusion of LCV gel phantom over time were evaluated. The gel formulation consisted of 25 mM Trichloroacetic acid, 1mM LCV, 4 mM Triton X-100, 4% gelatin by mass and distilled water. The advantages of using this gel are its tissue equivalence, easy and less preparation time, lower diffusion rate and it can be read with an optical scanner. We were able to reproduce some of the results of Babic et al. The peak absorption was found to be at 600 nm and hence a matrix of yellow LEDs was used as light source. The profiles obtained from projection images confirmed the diffusion of LCV gel after 6 hours of irradiation. Hence the LCV gel phantom should be read before 6 hours post irradiation to get accurate dose information as suggested previously.

  9. Actuator device utilizing a conductive polymer gel

    DOEpatents

    Chinn, Douglas A.; Irvin, David J.

    2004-02-03

    A valve actuator based on a conductive polymer gel is disclosed. A nonconductive housing is provided having two separate chambers separated by a porous frit. The conductive polymer is held in one chamber and an electrolyte solution, used as a source of charged ions, is held in the second chamber. The ends of the housing a sealed with a flexible elastomer. The polymer gel is further provide with electrodes with which to apply an electrical potential across the gel in order to initiate an oxidation reaction which in turn drives anions across the porous frit and into the polymer gel, swelling the volume of the gel and simultaneously contracting the volume of the electrolyte solution. Because the two end chambers are sealed the flexible elastomer expands or contracts with the chamber volume change. By manipulating the potential across the gel the motion of the elastomer can be controlled to act as a "gate" to open or close a fluid channel and thereby control flow through that channel.

  10. The Gel Electrophoresis Markup Language (GelML) from the Proteomics Standards Initiative

    PubMed Central

    Gibson, Frank; Hoogland, Christine; Martinez-Bartolomé, Salvador; Medina-Aunon, J. Alberto; Albar, Juan Pablo; Babnigg, Gyorgy; Wipat, Anil; Hermjakob, Henning; Almeida, Jonas S; Stanislaus, Romesh; Paton, Norman W; Jones, Andrew R

    2011-01-01

    The Human Proteome Organisation’s Proteomics Standards Initiative (HUPO-PSI) has developed the GelML data exchange format for representing gel electrophoresis experiments performed in proteomics investigations. The format closely follows the reporting guidelines for gel electrophoresis, which are part of the Minimum Information About a Proteomics Experiment (MIAPE) set of modules. GelML supports the capture of metadata (such as experimental protocols) and data (such as gel images) resulting from gel electrophoresis so that laboratories can be compliant with the MIAPE Gel Electrophoresis guidelines, while allowing such data sets to be exchanged or downloaded from public repositories. The format is sufficiently flexible to capture data from a broad range of experimental processes, and complements other PSI formats for mass spectrometry data and the results of protein and peptide identifications to capture entire gel-based proteome workflows. GelML has resulted from the open standardisation process of PSI consisting of both public consultation and anonymous review of the specifications. PMID:20677327

  11. Comparative Genome Analysis of Wheat Blue Dwarf Phytoplasma, an Obligate Pathogen That Causes Wheat Blue Dwarf Disease in China

    PubMed Central

    Chen, Wang; Li, Yan; Wang, Qiang; Wang, Nan; Wu, Yunfeng

    2014-01-01

    Wheat blue dwarf (WBD) disease is an important disease that has caused heavy losses in wheat production in northwestern China. This disease is caused by WBD phytoplasma, which is transmitted by Psammotettix striatus. Until now, no genome information about WBD phytoplasma has been published, seriously restricting research on this obligate pathogen. In this paper, we report a new sequencing and assembling strategy for phytoplasma genome projects. This strategy involves differential centrifugation, pulsed-field gel electrophoresis, whole genome amplification, shotgun sequencing, de novo assembly, screening of contigs from phytoplasma and the connection of phytoplasma contigs. Using this scheme, the WBD phytoplasma draft genome was obtained. It was comprised of six contigs with a total size of 611,462 bp, covering ∼94% of the chromosome. Five-hundred-twenty-five protein-coding genes, two operons for rRNA genes and 32 tRNA genes were identified. Comparative genome analyses between WBD phytoplasma and other phytoplasmas were subsequently carried out. The results showed that extensive arrangements and inversions existed among the WBD, OY-M and AY-WB phytoplasma genomes. Most protein-coding genes in WBD phytoplasma were found to be homologous to genes from other phytoplasmas; only 22 WBD-specific genes were identified. KEGG pathway analysis indicated that WBD phytoplasma had strongly reduced metabolic capabilities. However, 46 transporters were identified, which were involved with dipeptides/oligopeptides, spermidine/putrescine, cobalt and Mn/Zn transport, and so on. A total of 37 secreted proteins were encoded in the WBD phytoplasma chromosome and plasmids. Of these, three secreted proteins were similar to the reported phytoplasma virulence factors TENGU, SAP11 and SAP54. In addition, WBD phytoplasma possessed several proteins that were predicted to play a role in its adaptation to diverse environments. These results will provide clues for research on the pathogenic

  12. Coloration of silver-stained protein bands in polyacrylamide gels is caused by light scattering from silver grains of characteristic sizes.

    PubMed Central

    Merril, C R; Bisher, M E; Harrington, M; Steven, A C

    1988-01-01

    This study investigates the physical basis of color effects in the detection of proteins in polyacrylamide gels by silver staining. Specifically, the hypothesis that different colors may correlate with the development of silver grains of characteristic sizes was investigated by electron microscopy. Protein bands that stained brown, yellow, and blue were excised from stained gels and prepared for electron microscopy by thin-sectioning. In each case, the size distributions of globular silver grains were determined directly from the electron micrographs. We found that blue bands have larger silver grains (with diameters of 40-100 nm) than yellow (21-39 nm) or brown bands (17-35 nm). On the basis of these and other observations, a general mechanism is proposed whereby chemical specificity of electrophoretically separated proteins is expressed in color-specific silver staining. Images PMID:2448776

  13. Rare Earth based Sol-Gel Materials: An Intra- and Inter- Collegiate Collaborative Research Project

    NASA Astrophysics Data System (ADS)

    Silversmith, Ann

    2004-03-01

    Sol-gel glasses containing rare earth (RE) impurities form an exciting class of new optical materials with potential uses as phosphors and solid state laser media. The low temperature glass synthesis based on the liquid organic precursor tetramethoxysilane allows incorporation of higher RE concentrations than in traditional melt glasses without compromising the amorphous character of the material. The synthesis and spectroscopic characterization of these materials have together formed the basis for a fruitful interdisciplinary and multi-institutional research collaboration. All materials used in this project are made by Hamilton College chemistry students; spectroscopy experiments are performed by students and faculty in the physics departments at Hamilton, Franklin and Marshall, and Davidson Colleges. In this talk results from two ongoing spectroscopic investigations will be presented, both connected to the long-term goal of improving the low fluorescence efficiency of these materials. The first is the chelation of the RE metal to create an enhanced fluorescence excitation path and to physically separate the RE from the sol-gel matrix. Chelating molecules absorb strongly in the uv, and subsequent energy transfer can produce intense visible emission from the RE. Results are presented for the chelating agent 2,6-pyridine-dicarboxylic acid (PDC) bound to europium ions and incorporated into gels. Red emission from europium follows excitation into the PDC absorption band below 300nm. The second investigation focuses on fluorescence quenching of blue emission from trivalent terbium. Two separate mechanisms -energy transfer from terbium to residual hydroxide ions and among terbium ions - lead to reduced intensity of the blue emission lines relative to other longer wavelength signals.

  14. Preparation and characterization of lidocaine rice gel for oral application.

    PubMed

    Okonogi, Siriporn; Kaewpinta, Adchareeya; Yotsawimonwat, Songwut; Khongkhunthian, Sakornrat

    2015-12-01

    The objective of the present study was to prepare buccal anesthetic gels using rice as gelling agent. Rice grains of four rice varieties, Jasmine (JM), Saohai (SH), Homnil (HN), and Doisket (DS) were chemically modified. Buccal rice gels, containing lidocaine hydrochloride as local anesthetic drug were formulated using the respective modified rice varieties. The gels were evaluated for outer appearance, pH, color, gel strength, foaming property, adhesion, in vitro drug release and in vivo efficacy. It was found that the developed rice gels possessed good texture. Rice varieties showed influence on gel strength, color, turbidity, adhesive property, release property, and anesthetic efficacy. JM gel showed the lowest turbidity with light transmission of 86.76 ± 1.18% whereas SH gel showed the highest gel strength of 208.78 ± 10.42 g/cm(2). Lidocaine hydrochloride can cause a decrease in pH and adhesive property but an increase in turbidity of the gels. In vitro drug release profile within 60 min of lidocaine SH gel and lidocaine HN gel showed that lidocaine could be better released from SH gel. Evaluation of in vivo anesthetic efficacy in 100 normal volunteers indicates that both lidocaine rice gels have high efficacy but different levels. Lidocaine SH gel possesses faster onset of duration and longer duration of action than lidocaine HN gel. PMID:26781924

  15. 21 CFR 524.660b - Dimethyl sulfoxide gel.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 6 2011-04-01 2011-04-01 false Dimethyl sulfoxide gel. 524.660b Section 524.660b... Dimethyl sulfoxide gel. (a) Specifications. Dimethyl sulfoxide gel, veterinary contains 90 percent dimethyl sulfoxide in an aqueous gel. (b) Sponsor. See No. 000856 in § 510.600(c) of this chapter. (c) Conditions...

  16. Uncertainty in 3D gel dosimetry

    NASA Astrophysics Data System (ADS)

    De Deene, Yves; Jirasek, Andrew

    2015-01-01

    Three-dimensional (3D) gel dosimetry has a unique role to play in safeguarding conformal radiotherapy treatments as the technique can cover the full treatment chain and provides the radiation oncologist with the integrated dose distribution in 3D. It can also be applied to benchmark new treatment strategies such as image guided and tracking radiotherapy techniques. A major obstacle that has hindered the wider dissemination of gel dosimetry in radiotherapy centres is a lack of confidence in the reliability of the measured dose distribution. Uncertainties in 3D dosimeters are attributed to both dosimeter properties and scanning performance. In polymer gel dosimetry with MRI readout, discrepancies in dose response of large polymer gel dosimeters versus small calibration phantoms have been reported which can lead to significant inaccuracies in the dose maps. The sources of error in polymer gel dosimetry with MRI readout are well understood and it has been demonstrated that with a carefully designed scanning protocol, the overall uncertainty in absolute dose that can currently be obtained falls within 5% on an individual voxel basis, for a minimum voxel size of 5 mm3. However, several research groups have chosen to use polymer gel dosimetry in a relative manner by normalizing the dose distribution towards an internal reference dose within the gel dosimeter phantom. 3D dosimetry with optical scanning has also been mostly applied in a relative way, although in principle absolute calibration is possible. As the optical absorption in 3D dosimeters is less dependent on temperature it can be expected that the achievable accuracy is higher with optical CT. The precision in optical scanning of 3D dosimeters depends to a large extend on the performance of the detector. 3D dosimetry with X-ray CT readout is a low contrast imaging modality for polymer gel dosimetry. Sources of error in x-ray CT polymer gel dosimetry (XCT) are currently under investigation and include inherent

  17. Synthesis and Study of Gel Calcined Cd-Sn Oxide Nanocomposites

    NASA Astrophysics Data System (ADS)

    De, Arijit; Kundu, Susmita

    2016-05-01

    Cd-Sn oxide nanocomposites were synthesized by sol-gel method from precursor sol containing Cd:Sn = 2:1 and 1:1 mol ratio. Instead of coprecipitation, a simple novel gel calcination route was followed. Cd (NO3)2. 4H2O and SnCl4. 5H2O were used as starting materials. Gel was calcined at 1050 °C for 2 h to obtain nanocomposites. XRD analysis reveals the presence of orthorhombic, cubic Cd2SnO4 along with orthorhombic, hexagonal CdSnO3 phases in both the composites. SEM and TEM studies indicate the development of nanocomposites of different shapes suggesting different degrees of polymerization in precursor sol of different composition. UV-Vis absorption spectra show a blue shift for both the composites compared to bulk values. Decrease of polarization with frequency, dipole contribution to the polarization, and more sensitivity to ethanol vapor were observed for the nanocomposite derived from precursor sol containing Cd:Sn = 2:1 mol ratio.

  18. TiO2/PCL hybrid materials synthesized via sol-gel technique for biomedical applications.

    PubMed

    Catauro, M; Bollino, F; Papale, F; Marciano, S; Pacifico, S

    2015-02-01

    The aim of the present work has been the synthesis of organic/inorganic hybrid materials based on titanium dioxide and poly(ε-caprolactone) (PCL) to be used in the biomedical field. Several materials have been synthesized using sol-gel methods by adding different amounts of polymer to the inorganic sol. The obtained gels have been characterized using Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM) and atomic force microscopy (AFM). The FT-IR data allowed us to hypothesize that the structure formed was that of an interpenetrating network, realized by hydrogen bonds between TiOH groups in the sol-gel intermediate species and carbonyl groups in the polymer repeating units. SEM and AFM analyses highlighted that the obtained materials were nanostructurated hybrids. To evaluate the biological properties of the hybrids, their bioactivity and cytotoxicity were investigated as a function of the PCL amount. The bioactivity of the synthesized systems was proven by the formation of a hydroxyapatite layer on the surface of samples soaked in a fluid simulating human blood plasma (SBF). MTT cytotoxicity tests and Trypan Blue dye exclusion tests were carried out exposing NIH-3T3 mouse embryonic fibroblasts for 24 and 48h to extracts from the investigated hybrid materials. The results showed that all the hybrids had a non-cytotoxic effect on target cells. PMID:25492181

  19. Clinical Effects of Subgingivally Delivered Spirulina Gel in Chronic Periodontitis Cases: A Placebo Controlled Clinical Trial

    PubMed Central

    Mahendra, Jaideep; Mahendra, Little; Muthu, Jananni; John, Libby; Romanos, Georgios E.

    2013-01-01

    Aims and Objectives: The aim of this study was to assess the clinical effects of Spirulina in-situ gel as an adjunct to Scaling And Root Planning (SRP) in the treatment of chronic periodontitis subjects. Material and Methods: 64 sites were selected with probing pocket depth of ≥5mm and they were divided into 2 groups; 33 sites were treated with SRP along with spirulina gel (Group A) and 31 sites were treated with SRP alone (Group B). Clinical parameters were recorded at baseline before SRP and at 120th day after the treatment therapy. The parameters included Probing Pocket Depth (PPD) and Clinical Attachment Level (CAL). Results: Both the groups showed significant improvement in the parameters. However, Group A (SRP along with spirulina) showed statistically significant decrease in mean probing pocket depth and gain in the clinical attachment level after 120 days as compared to Group B SRP alone. Conclusion: Locally delivered spirulina gel, along with scaling and root planning, has been shown to cause a beneficial impact. The efficacy of the product as a local drug delivery system in the non-surgical treatment of periodontitis without any side effects has been proved. Spirulina appears to be promising. It exerts strong anti-inflammatory effects which are closely connected with its antioxidative activity. This study can have a significant impact on the treatment procedures of periodontitis, with the use of blue green algae in the future. PMID:24298522

  20. Photocatalytic activity of titania coatings synthesised by a combined laser/sol–gel technique

    SciTech Connect

    Adraider, Y.; Pang, Y.X.; Nabhani, F.; Hodgson, S.N.; Sharp, M.C.; Al-Waidh, A.

    2014-06-01

    Highlights: • Sol–gel method was used to prepare titania coatings. • Titania thin films were coated on substrate surface by dip coating. • Fibre laser was employed to irradiate the titania coated surfaces. • Photocatalytic efficiency of titania coatings was significantly improved after laser processing. - Abstract: Titania coatings were prepared using sol–gel method and then applied on the substrate surface by dip coating. Fibre laser (λ = 1064 nm) in continuous wave mode was used to irradiate the titania coated surfaces at different specific energies. The ATR-FTIR, XRD, SEM, EDS and contact angle measurement were employed to analyse surface morphology, phase composition and crystalline structure of laser-irradiated titania coatings, whilst the photocatalytic activity was evaluated by measuring the decomposition of methylene blue (MB) after exposure to the visible light for various illumination times. Results showed that the laser-irradiated titania coatings demonstrate significant different composition and microstructure in comparison with the as-coated from the same sol–gel titania. Photocatalytic efficiency of titania coatings was significantly improved after laser processing. The photocatalytic activity of laser-irradiated titania coatings was higher than that of the as-coated titania. The titania coating processed at laser specific energy of 6.5 J/mm{sup 2} exhibited the highest photocatalytic activity among all titania samples.

  1. Phosphoproteome profiling using a fluorescent phosphosensor dye in two-dimensional polyacrylamide gel electrophoresis.

    PubMed

    Otani, Mieko; Taniguchi, Taizo; Sakai, Akiko; Seta, Jouji; Kadoyama, Keiichi; Nakamura-Hirota, Tooru; Matsuyama, Shogo; Sano, Keiji; Takano, Masaoki

    2011-07-01

    We validated the novel PhosphoQUANTI SolidBlue Complex (PQSC) dye for the sensitive fluorescent detection of phosphorylated proteins in polyacrylamide- and two-dimensional gel electrophoresis (PAGE and 2DE, respectively). PQSC can detect as little as 15.6 ng of ß-casein, a pentaphosphorylated protein, and 61.3 ng of ovalbumin, a diphosphorylated protein. Fluorescence intensity correlates with the number of phosphorylated residues on the protein. To demonstrate the specificity of PQSC for phosphoproteins, enzymatically dephosphorylated lysates of Swiss 3T3 cells were separated in 2DE gels and stained by PQSC. The fluorescence signals in these gels were markedly reduced following dephosphorylation. When the phosphorylated proteins in Swiss 3T3 cell lysates were concentrated using a phosphoprotein enrichment column, the majority of phosphoproteins showed fluorescence signals in the pI 4-5 range. Finally, we performed phosphoproteome analysis to study differences in the protein phosphorylation profiles of proliferating and quiescent Swiss 3T3 cells. Over 135 discernible protein spots were detected, from which a selection of 15 spots were identified by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI TOF-MS). The PQSC staining procedure for phosphoprotein detection is simple, reversible, and fully compatible with MALDI TOF-MS. PMID:21384102

  2. Synthesis and Study of Gel Calcined Cd-Sn Oxide Nanocomposites

    NASA Astrophysics Data System (ADS)

    De, Arijit; Kundu, Susmita

    2016-07-01

    Cd-Sn oxide nanocomposites were synthesized by sol-gel method from precursor sol containing Cd:Sn = 2:1 and 1:1 mol ratio. Instead of coprecipitation, a simple novel gel calcination route was followed. Cd (NO3)2. 4H2O and SnCl4. 5H2O were used as starting materials. Gel was calcined at 1050 °C for 2 h to obtain nanocomposites. XRD analysis reveals the presence of orthorhombic, cubic Cd2SnO4 along with orthorhombic, hexagonal CdSnO3 phases in both the composites. SEM and TEM studies indicate the development of nanocomposites of different shapes suggesting different degrees of polymerization in precursor sol of different composition. UV-Vis absorption spectra show a blue shift for both the composites compared to bulk values. Decrease of polarization with frequency, dipole contribution to the polarization, and more sensitivity to ethanol vapor were observed for the nanocomposite derived from precursor sol containing Cd:Sn = 2:1 mol ratio.

  3. My maize and blue brick road to physical organic chemistry in materials.

    PubMed

    McNeil, Anne J

    2016-01-01

    Similar to Dorothy's journey along the yellow brick road in The Wizard of Oz, this perspective carves out the path I took from my early childhood fascinations with science through my independent career at the University of Michigan (maize and blue). The influential research projects and mentors are highlighted, including some fortuitous experimental results that drew me into the field of supramolecular chemistry, specifically, and organic materials, broadly. My research group's efforts toward designing new sensors based on small molecule gelators are described. In particular, I highlight how our design strategy has evolved as we learn more about molecular gelators. This perspective concludes with some predictions about where molecular gels, as well as my personal and professional life, are headed. PMID:26977181

  4. Photodegradation of bromophenol blue with fluorinated TiO2 composite

    NASA Astrophysics Data System (ADS)

    Dlamini, L. N.; Krause, R. W.; Kulkarni, G. U.; Durbach, S. H.

    2011-09-01

    Fluorinated TiO2 composites were prepared by the sol-gel method. The photocatalytic activities of the composites were evaluated with bromophenol blue (BPB). Composites which contained carbon nanotubes showed the highest photodegradation (98%) of BPB at 20 min as compared to pure TiO2. Photodegradation by-products of BPB such as Br- and [SO4]2- ions were monitored with ion chromatography. All catalysts were characterized with microscopic techniques, including transmission electron microscopy and scanning electron microscopy which were both equipped with an energy dispersive X-ray spectrophotometer. The polymorph of TiO2 was verified by the use of Raman spectroscopy and powder X-ray diffraction.

  5. Studies on the proteins of mass-cultivated, blue-green alga (Spirulina platensis)

    SciTech Connect

    Annusuyadevi, M.; Subbulakshmi, G.; Madhair'devi, K.; Venkalaramein, L.V.

    1981-05-01

    The characteristics of the protein of fresh-water, mass-cultured Spirulina platensis have been studied. The solubility of this algal protein in water and various aqueous solvents has been estimated. The total protein content of the blue-green algae was approximately 50-55% of which nearly 9.9% was nonprotein nitrogen. About 80% of the total protein nitrogen can be extracted by three successive extractions with water. Ths isoelectric point of this algal protein is found to be 3.0. The total proteins were characterized physicochemically by standard techniques. In the ultracentrifuge total proteins resolve into two major components with S20w values of 2.6 and 4.7 S. The polyacrylamide gel electrophoretic pattern of the total protein showed seven bands including three prominent ones. The in vitro digestibility of the total protein of fresh algae was found to be 85% when assayed with a pepsin-pancreatin system.

  6. My maize and blue brick road to physical organic chemistry in materials

    PubMed Central

    2016-01-01

    Summary Similar to Dorothy’s journey along the yellow brick road in The Wizard of Oz, this perspective carves out the path I took from my early childhood fascinations with science through my independent career at the University of Michigan (maize and blue). The influential research projects and mentors are highlighted, including some fortuitous experimental results that drew me into the field of supramolecular chemistry, specifically, and organic materials, broadly. My research group’s efforts toward designing new sensors based on small molecule gelators are described. In particular, I highlight how our design strategy has evolved as we learn more about molecular gelators. This perspective concludes with some predictions about where molecular gels, as well as my personal and professional life, are headed. PMID:26977181

  7. Fabricating porous materials using interpenetrating inorganic-organic composite gels

    DOEpatents

    Seo, Dong-Kyun; Volosin, Alex

    2016-06-14

    Porous materials are fabricated using interpenetrating inorganic-organic composite gels. A mixture or precursor solution including an inorganic gel precursor, an organic polymer gel precursor, and a solvent is treated to form an inorganic wet gel including the organic polymer gel precursor and the solvent. The inorganic wet gel is then treated to form a composite wet gel including an organic polymer network in the body of the inorganic wet gel, producing an interpenetrating inorganic-organic composite gel. The composite wet gel is dried to form a composite material including the organic polymer network and an inorganic network component. The composite material can be treated further to form a porous composite material, a porous polymer or polymer composite, a porous metal oxide, and other porous materials.

  8. Recycling of superfine resolution agarose gel.

    PubMed

    Seng, T-Y; Singh, R; Faridah, Q Z; Tan, S-G; Alwee, S S R S

    2013-01-01

    Genetic markers are now routinely used in a wide range of applications, from forensic DNA analysis to marker-assisted plant and animal breeding. The usual practice in such work is to extract the DNA, prime the markers of interest, and sift them out by electrically driving them through an appropriate matrix, usually a gel. The gels, made from polyacrylamide or agarose, are of high cost, limiting their greater applications in molecular marker work, especially in developing countries where such technology has great potential. Trials using superfine resolution (SFR) agarose for SSR marker screening showed that it is capable of resolving SSR loci and can be reused up to 14 times, thus greatly reducing the cost of each gel run. Furthermore, for certain applications, low concentrations of agarose sufficed and switching to lithium borate buffer, instead of the conventional Tris-borate-ethylenediaminetetraacetic acid buffer, will further save time and cost. The 2.5% gel was prepared following the Agarose SFR(TM) manual by adding 2.5 g agarose powder into 100 mL 1X lithium borate buffer in a 250-mL flask with rapid stirring. Two midigels (105 x 83 mm, 17 wells) or 4 minigels (50 x 83 mm, 8 wells), 4 mm thickness can be prepared from 100 mL gel solution. A total of 1680 PCR products amplified using 140 SSR markers from oil palm DNA samples were tested in this study using SFR recycled gel. As average, the gel can be recycled 8 times with good resolution, but can be recycled up to 14 times before the resolutions get blurred. PMID:23546970

  9. Why are blue zhamanshinites blue Liquid immiscibility in an impact melt

    SciTech Connect

    Zolensky, M.E. ); Koeberl, C. )

    1991-05-01

    The authors report here a study of the cause of the coloration of blue zhamanshinites, which are glassy impact melt rocks from the Zhamanshin crater in the USSR. They find that the blue color results from Rayleigh scattering from spherical, 100 nm-diameter inclusions of a separate Ca-Fe-Mg-P-rich silicate glass. These observations can best be explained by the operation of liquid immiscibility in the zhamanshinite melt, and suggest that liquid immiscibility may have a more general role in impactite evolution.

  10. Why are blue zhamanshinites blue? Liquid immiscibility in an impact melt

    NASA Technical Reports Server (NTRS)

    Zolensky, Michael E.; Koeberl, Christian

    1991-01-01

    A study of the cause of the coloration of blue zhamanshinites, which are glassy impact melt rocks from the Zhamanshin crater in the USSR are reported. It is found that the blue color results from Rayleigh scattering from spherical, 100 nm-diameter inclusions of a separate Ca-Fe-Mg-P-rich silicate glass. These observations can best be explained by the operation of liquid immiscibility in the zhamanshinite melt, and suggest that liquid immiscibility may have a more general role in impactite evolution.

  11. Heat-set gel-like networks of lipophilic Co(II) triazole complexes in organic media and their thermochromic structural transitions.

    PubMed

    Kuroiwa, Keita; Shibata, Tomoko; Takada, Akihiko; Nemoto, Norio; Kimizuka, Nobuo

    2004-02-25

    A novel class of thermally responsive supramolecular assemblies is formed from the lipophilic cobalt(II) complexes of 4-alkylated 1,2,4-triazoles. When an ether linkage is introduced in the alkylchain moiety, a blue gel-like phase is formed in chloroform, even at very low concentration (ca. 0.01 wt %, at room temperature). The blue color is accompanied by a structured absorption around 580-730 nm, which is characteristic of cobalt (II) in the tetrahedral (T(d)) coordination. Atomic force microscopy (AFM) and transmission electron microscopy (TEM) of the gel-like phase confirms the formation of networks of fibrous nanoassemblies with widths of 5-30 nm. The observed widths are larger than a molecular length of the triazole ligand (ca. 2.2 nm) and they are consisted of aggregates of T(d) coordination polymers. Very interestingly, the blue gel-like phase turned into a solution by cooling below 25 degrees C. A pale pink solution is obtained at 0 degrees C, indicating the formation of octahedral (O(h)) complexes. The observed thermochromic transition is totally reversible. The formation of gel-like networks by heating is contrary to the conventional organogels, which dissolve upon heating. Temperature dependence of the storage and loss moduli (G' and G") shows minima around at 27 degrees C, at which temperature they gave comparable values. On the other hand, G' exceeds G" both in the gel-like phase (temperature above 27 degrees C) and in the solution phase (temperature below 25 degrees C). These observations indicate that T(d) complexes are present as low-molecular weight species around at 25-27 degrees C. They are self-assembled to polymeric T(d) complexes by heating and form gel-like networks. Upon cooling the solution below 25 degrees C, T(d) complexes are converted to O(h) complexes and they also self-assemble into oligomeric or polymeric species at lower temperatures. The observed unique thermochromic transition (pink solution --> blue gel-like phase) is accompanied

  12. Optimal processing for gel electrophoresis images: Applying Monte Carlo Tree Search in GelApp.

    PubMed

    Nguyen, Phi-Vu; Ghezal, Ali; Hsueh, Ya-Chih; Boudier, Thomas; Gan, Samuel Ken-En; Lee, Hwee Kuan

    2016-08-01

    In biomedical research, gel band size estimation in electrophoresis analysis is a routine process. To facilitate and automate this process, numerous software have been released, notably the GelApp mobile app. However, the band detection accuracy is limited due to a band detection algorithm that cannot adapt to the variations in input images. To address this, we used the Monte Carlo Tree Search with Upper Confidence Bound (MCTS-UCB) method to efficiently search for optimal image processing pipelines for the band detection task, thereby improving the segmentation algorithm. Incorporating this into GelApp, we report a significant enhancement of gel band detection accuracy by 55.9 ± 2.0% for protein polyacrylamide gels, and 35.9 ± 2.5% for DNA SYBR green agarose gels. This implementation is a proof-of-concept in demonstrating MCTS-UCB as a strategy to optimize general image segmentation. The improved version of GelApp-GelApp 2.0-is freely available on both Google Play Store (for Android platform), and Apple App Store (for iOS platform). PMID:27251892

  13. Evolution of gel structure during thermal processing of Na-geopolymer gels.

    PubMed

    Duxson, Peter; Lukey, Grant C; van Deventer, Jannie S J

    2006-10-10

    The present work examines how the gel structure and phase composition of Na-geopolymers derived from metakaolin with varied Si/Al ratio evolve with exposure to temperatures up to 1000 degrees C. Gels were thermally treated and characterized using quantitative XRD, DTA, and FTIR to elucidate the changes in gel structure, phase composition, and porosity at each stage of heating. It is found that the phase stability, defined by the amount and onset temperature of crystallization, is improved at higher Si/Al ratios. Two different mechanisms of densification have been isolated by FTIR, related to viscous flow and collapse of the highly distributed pore network in the gel. Gels with low Si/Al ratio only experience viscous flow that correlates with low thermal shrinkage. Gels at a higher Si/Al ratio, which have a homogeneous microstructure composed of a highly distributed porosity, undergo both densification processes corresponding to a large extent of thermal shrinkage during densification. This work elucidates the intimate relationship between gel microstructure, chemistry, and thermal evolution of Na-geopolymer gels. PMID:17014113

  14. MOCK OBSERVATIONS OF BLUE STRAGGLERS IN GLOBULAR CLUSTER MODELS

    SciTech Connect

    Sills, Alison; Glebbeek, Evert; Chatterjee, Sourav; Rasio, Frederic A. E-mail: e.glebbeek@astro.ru.nl E-mail: rasio@northwestern.edu

    2013-11-10

    We created artificial color-magnitude diagrams of Monte Carlo dynamical models of globular clusters and then used observational methods to determine the number of blue stragglers in those clusters. We compared these blue stragglers to various cluster properties, mimicking work that has been done for blue stragglers in Milky Way globular clusters to determine the dominant formation mechanism(s) of this unusual stellar population. We find that a mass-based prescription for selecting blue stragglers will select approximately twice as many blue stragglers than a selection criterion that was developed for observations of real clusters. However, the two numbers of blue stragglers are well-correlated, so either selection criterion can be used to characterize the blue straggler population of a cluster. We confirm previous results that the simplified prescription for the evolution of a collision or merger product in the BSE code overestimates their lifetimes. We show that our model blue stragglers follow similar trends with cluster properties (core mass, binary fraction, total mass, collision rate) as the true Milky Way blue stragglers as long as we restrict ourselves to model clusters with an initial binary fraction higher than 5%. We also show that, in contrast to earlier work, the number of blue stragglers in the cluster core does have a weak dependence on the collisional parameter Γ in both our models and in Milky Way globular clusters.

  15. Sol-gel processing of metal sulfides

    NASA Astrophysics Data System (ADS)

    Stanic, Vesha

    Metal sulfides were synthesised via a sol-gel process using various metal alkoxides and hydrogen sulfide in toluene. Colloidal gels were prepared from germanium ethoxide, germanium isopropoxide, zinc tert-butoxide and tungsten (VI) ethoxide, whereas colloidal powder was produced from tungsten (V) dichloride ethoxide. Special precautions were necessary to protect the reaction mixture from water contamination which produced metal oxides. Results indicated that the main source of water is the hydrogen sulfide gas. In addition, synthesis of metal sulfides from a mixture of metal oxide and sulfide was demonstrated by the example of monoclinic germanium disulfide. It was produced by reaction of the sol-gel product with sulfur. Heat treatment of the sol-gel product and sulfur yielded single phase GeSsb2. The sol-gel prepared materials and their heat treated products were characterized by various methods. A chemical kinetics study of the functional groups -OR, -SH and Ssp{2-} was carried out for the sol-gel processing of GeSsb2 from of hydrogen sulfide and two different alkoxides, germanium ethoxide and germanium isopropoxide. The study was performed for different concentrations of precursors at different molar ratios and temperatures. The results indicate that the proposed reaction mechanism was simplified under appropriate reaction conditions. Experimentally determined rate constants of thiolysis and condensations demonstrate that thiolysis is slow and that condensations are fast steps, regardless of the studied reaction conditions. A study of the temperature effect on the reaction rate constant shows that it increases with temperature in accord with both Arrhenius law and transition-state theory. Activation energies, Esba, and activation parameters DeltaSsp{ddagger}, DeltaHsp{ddagger} and DeltaGsp{ddagger}, were determined for thiolysis and condensation reactions. The potentiometric tiration method was used for quantitative determination of germanium sulfide and

  16. Nile Blue derivatives as lysosomotropic photosensitizers

    NASA Astrophysics Data System (ADS)

    Lin, Chi-Wei; Shulok, Janine R.; Kirley, S. D.; Cincotta, Louis; Foley, James W.

    1991-06-01

    The benzophenoxazines, including several Nile blue analogues, are a unique group of dyes that localize selectively in animal tumors. Chemical modifications of Nile blue A can yield derivatives with high 1O2 quantum yields. These derivatives represent a group of potentially effective photosensitizers for selective phototherapy of malignant tumors. In vitro evaluation of these derivatives has indicated that those with high 1O2 yields are very effective in mediating the photocytotoxicity of tumor cells. This photodynamic effect is most likely mediated through the action of 1O2, since photoirradiation under D2O enhanced and under hypoxic conditions diminished the photocytotoxic action. The subcellular localization of these photosensitizers in bladder tumor cells in culture was examined by light and fluorescence microscopies as well as by histochemical and biochemical studies. The results indicate that these dyes are localized primarily in the lysosome. The cellular uptake and retention of these dyes is energy- and pH-dependent. Agents such as nigericin, which alter the transmembrane pH gradient, reduced uptake and enhanced efflux of the dyes, while agents such as valinomycin, which reduce cellular membrane potential, had no effect on the uptake. These findings are consistent with having ion-trapping as the mechanism for the uptake of these dyes. Photoirradiation of sensitizer-treated cells obliterated lysosomes in a light-dose and drug-dose dependent fashion. Release of the hydrolytic enzymes may be the main cause for subsequent cell death since the cytolytic effect was reduced by a specific inhibitor of lysosomal proteolytic enzyme. A lysosomotropic photosensitization mechanism is therefore proposed for the photocytotoxic action of the Nile blue derivatives. This mechanism may provide an approach to the development of new photosensitizers for the effective and selective destruction of malignant tumors.

  17. Reversible Gel-Sol Transition of a Photo-Responsive DNA Gel.

    PubMed

    Kandatsu, Daisuke; Cervantes-Salguero, Keitel; Kawamata, Ibuki; Hamada, Shogo; Nomura, Shin-Ichiro M; Fujimoto, Kenzo; Murata, Satoshi

    2016-06-16

    Stimuli-responsive DNA gels that can undergo a sol-gel transition in response to photo-irradiation provide a way to engineer functional gel material with fully designed DNA base sequences. We propose an X-shaped DNA motif that turns into a gel by hybridization of self-complementary sticky ends. By embedding a photo-crosslinking artificial base in the sticky-end sequence, repetitive gel-sol transitions are achieved through UV irradiation at different wavelengths. The concentration of the DNA motif necessary for gelation is as low as 40 μm after modification of the geometrical properties of the motif. The physical properties, such as swelling degree and diffusion coefficient, were assessed experimentally. PMID:27123549

  18. Comparison of electrical conductivities of various brain phantom gels: Developing a ‘Brain Gel Model’

    PubMed Central

    Kandadai, Madhuvanthi A.; Raymond, Jason L.; Shaw, George J.

    2012-01-01

    The use of conducting gels to mimic brain and other tissues is of increasing interest in the development of new medical devices. Currently, there are few such models that can be utilized at physiologic temperatures. In this work, the conductivities of agar, agarose and gelatin gels were manipulated by varying NaCl concentration from 0–1 mg/ml. The AC conductivity was measured at room and physiological temperatures (37°C) in the 100–500 Hz frequency range. Conductivity (σ) was nearly independent of frequency but increased linearly with NaCl concentration and was higher at physiological temperatures in these gels. A formula for predicting conductivity as a function of NaCl concentration was derived for each gel type. The overall goal is to develop a ‘brain gel model’, for studying low frequency electrical properties of the brain and other tissues at physiological temperatures. PMID:23139442

  19. Comparison of electrical conductivities of various brain phantom gels: Developing a 'Brain Gel Model'

    PubMed

    Kandadai, Madhuvanthi A; Raymond, Jason L; Shaw, George J

    2012-12-01

    The use of conducting gels to mimic brain and other tissues is of increasing interest in the development of new medical devices. Currently, there are few such models that can be utilized at physiologic temperatures. In this work, the conductivities of agar, agarose and gelatin gels were manipulated by varying NaCl concentration from 0-1 mg/ml. The AC conductivity was measured at room and physiological temperatures (37°C) in the 100-500 Hz frequency range. Conductivity (σ) was nearly independent of frequency but increased linearly with NaCl concentration and was higher at physiological temperatures in these gels. A formula for predicting conductivity as a function of NaCl concentration was derived for each gel type. The overall goal is to develop a 'brain gel model', for studying low frequency electrical properties of the brain and other tissues at physiological temperatures. PMID:23139442

  20. Enhanced detection of glycoproteins in polyacrylamide gels.

    PubMed

    Muñoz, G; Marshall, S; Cabrera, M; Horvat, A

    1988-05-01

    A highly sensitive and simple method to enhance detection of glycoproteins resolved by either one- or two-dimensional polyacrylamide gel electrophoresis is described. The method is a modification of the procedure described by D. Fargeaud et al. (D. Fargeaud, J. C. Benoit, F. Kato, and G. Chappuis (1984) Arch. Virol. 80, 69-82) that uses concanavalin A conjugated with fluorescein isothyocyanate to detect the carbohydrate moiety of glycoproteins. Briefly, the electrophoresed gel is exposed to the fluorescent lectin, thoroughly washed, and sequentially transferred to 50% methanol in deionized water and to absolute methanol. The result is an abrupt dehydration of the gel which turns evenly white and stiff. At least a twofold enhancement of fluorescence is obtained as detected by exposing the treated gel to an appropriate uv source. The sensitivity of the procedure allows us to detect purified immunoglobulin molecules by their carbohydrate content in the range of 0.2 microgram of total protein. The specificity of the detection is demonstrated by a comparison with the corresponding polypeptide profile obtained by silver nitrate staining of the gel. PMID:3394948

  1. Structural evolution of Colloidal Gels under Flow

    NASA Astrophysics Data System (ADS)

    Boromand, Arman; Maia, Joao; Jamali, Safa

    Colloidal suspensions are ubiquitous in different industrial applications ranging from cosmetic and food industries to soft robotics and aerospace. Owing to the fact that mechanical properties of colloidal gels are controlled by its microstructure and network topology, we trace the particles in the networks formed under different attraction potentials and try to find a universal behavior in yielding of colloidal gels. Many authors have implemented different simulation techniques such as molecular dynamics (MD) and Brownian dynamics (BD) to capture better picture during phase separation and yielding mechanism in colloidal system with short-ranged attractive force. However, BD neglects multi-body hydrodynamic interactions (HI) which are believed to be responsible for the second yielding of colloidal gels. We envision using dissipative particle dynamics (DPD) with modified depletion potential and hydrodynamic interactions, as a coarse-grain model, can provide a robust simulation package to address the gel formation process and yielding in short ranged-attractive colloidal systems. The behavior of colloidal gels with different attraction potentials under flow is examined and structural fingerprints of yielding in these systems will be discussed.

  2. Mucosal effects of tenofovir 1% gel.

    PubMed

    Hladik, Florian; Burgener, Adam; Ballweber, Lamar; Gottardo, Raphael; Vojtech, Lucia; Fourati, Slim; Dai, James Y; Cameron, Mark J; Strobl, Johanna; Hughes, Sean M; Hoesley, Craig; Andrew, Philip; Johnson, Sherri; Piper, Jeanna; Friend, David R; Ball, T Blake; Cranston, Ross D; Mayer, Kenneth H; McElrath, M Juliana; McGowan, Ian

    2015-01-01

    Tenofovir gel is being evaluated for vaginal and rectal pre-exposure prophylaxis against HIV transmission. Because this is a new prevention strategy, we broadly assessed its effects on the mucosa. In MTN-007, a phase-1, randomized, double-blinded rectal microbicide trial, we used systems genomics/proteomics to determine the effect of tenofovir 1% gel, nonoxynol-9 2% gel, placebo gel or no treatment on rectal biopsies (15 subjects/arm). We also treated primary vaginal epithelial cells from four healthy women with tenofovir in vitro. After seven days of administration, tenofovir 1% gel had broad-ranging effects on the rectal mucosa, which were more pronounced than, but different from, those of the detergent nonoxynol-9. Tenofovir suppressed anti-inflammatory mediators, increased T cell densities, caused mitochondrial dysfunction, altered regulatory pathways of cell differentiation and survival, and stimulated epithelial cell proliferation. The breadth of mucosal changes induced by tenofovir indicates that its safety over longer-term topical use should be carefully monitored. PMID:25647729

  3. Continuum Models of Stimuli-responsive Gels

    NASA Astrophysics Data System (ADS)

    Hong, Wei

    Immersed in a solution of small molecules and ions, a network of long-chain polymers may imbibe the solution and swell, resulting in a polymeric gel. Depending on the molecular structure of the polymers, the amount of swelling can be regulated by moisture, mechanical forces, ionic strength, electric field, pH value, and many other types of stimuli. Starting from the basic principles of non-equilibrium thermodynamics, this chapter formulates a field theory of the coupled large deformation and mass transportation in a neutral polymeric gel. The theory is then extended to study polyelectrolyte gels with charge-carrying networks by accounting for the electromechanical coupling and migration of solute ions. While the theoretical framework is adaptable to various types of material models, some representative ones are described through specific free-energy functions and kinetic laws. A specific material law for pH-sensitive gels—a special type of polyelectrolyte gels—is introduced as an example of incorporating chemical reactions in modeling stimuli-responsive gels. Finally, a simplified theory for the equilibrium but inhomogeneous swelling of a polymeric gel is deduced. The theory and the specific material models are illustrated through several examples.

  4. Toward sol-gel-based sensors

    SciTech Connect

    Jordan, J.D.; Ingersoll, C.M.; Dunbar, R.A.

    1995-12-31

    Advances in biotechnology have produced a variety of antibodies and other biomolecules that possess selective recognition capabilities. Current techniques for the immobilization of these biomolecules typically involve multistep derivatization of a primary substrate, which is labor intensive and often requires large volumes of costly reagents. Further, these immobilization chemistries often adversely affect the characteristic properties of the protein (e.g., the binding affinity). As a result, the need for fast, accurate, inexpensive, and simple to operate diagnostic assays escalates. Because of their room temperature processing, transparency, inertness, and tunable pore structure, sol-gel-derived composites represent promising chemical and biosensing platforms. To date, many researchers have entrapped proteins and enzymes in sol-gel monoliths, and found that they retain some of their native properties. Our group first reported on the affinity of a sol-gel entrapped antibody. However, although these biogel monoliths were promising, analyte diffusion through the monolith matrix is slow, resulting in long response times. Thus, it is clear that the next level of sol-gel-derived biosensor must depend on thin film technology. In the current work, the affinity of fluorescein entrapped within a sol-gel derived thin film for the anti fluorescent hapten, 5- (and 6-)-carboxy 4{prime}, 5{prime}-dimethylfluorescein, is investigated. A novel film preparation technique will be introduced, and the response and response times of these films as a function of processing and storage conditions will be discussed.

  5. DNA DAMAGE QUANTITATION BY ALKALINE GEL ELECTROPHORESIS.

    SciTech Connect

    SUTHERLAND,B.M.; BENNETT,P.V.; SUTHERLAND, J.C.

    2004-03-24

    Physical and chemical agents in the environment, those used in clinical applications, or encountered during recreational exposures to sunlight, induce damages in DNA. Understanding the biological impact of these agents requires quantitation of the levels of such damages in laboratory test systems as well as in field or clinical samples. Alkaline gel electrophoresis provides a sensitive (down to {approx} a few lesions/5Mb), rapid method of direct quantitation of a wide variety of DNA damages in nanogram quantities of non-radioactive DNAs from laboratory, field, or clinical specimens, including higher plants and animals. This method stems from velocity sedimentation studies of DNA populations, and from the simple methods of agarose gel electrophoresis. Our laboratories have developed quantitative agarose gel methods, analytical descriptions of DNA migration during electrophoresis on agarose gels (1-6), and electronic imaging for accurate determinations of DNA mass (7-9). Although all these components improve sensitivity and throughput of large numbers of samples (7,8,10), a simple version using only standard molecular biology equipment allows routine analysis of DNA damages at moderate frequencies. We present here a description of the methods, as well as a brief description of the underlying principles, required for a simplified approach to quantitation of DNA damages by alkaline gel electrophoresis.

  6. Mucosal effects of tenofovir 1% gel

    PubMed Central

    Hladik, Florian; Burgener, Adam; Ballweber, Lamar; Gottardo, Raphael; Vojtech, Lucia; Fourati, Slim; Dai, James Y; Cameron, Mark J; Strobl, Johanna; Hughes, Sean M; Hoesley, Craig; Andrew, Philip; Johnson, Sherri; Piper, Jeanna; Friend, David R; Ball, T Blake; Cranston, Ross D; Mayer, Kenneth H; McElrath, M Juliana; McGowan, Ian

    2015-01-01

    Tenofovir gel is being evaluated for vaginal and rectal pre-exposure prophylaxis against HIV transmission. Because this is a new prevention strategy, we broadly assessed its effects on the mucosa. In MTN-007, a phase-1, randomized, double-blinded rectal microbicide trial, we used systems genomics/proteomics to determine the effect of tenofovir 1% gel, nonoxynol-9 2% gel, placebo gel or no treatment on rectal biopsies (15 subjects/arm). We also treated primary vaginal epithelial cells from four healthy women with tenofovir in vitro. After seven days of administration, tenofovir 1% gel had broad-ranging effects on the rectal mucosa, which were more pronounced than, but different from, those of the detergent nonoxynol-9. Tenofovir suppressed anti-inflammatory mediators, increased T cell densities, caused mitochondrial dysfunction, altered regulatory pathways of cell differentiation and survival, and stimulated epithelial cell proliferation. The breadth of mucosal changes induced by tenofovir indicates that its safety over longer-term topical use should be carefully monitored. Clinical trial registration: NCT01232803. DOI: http://dx.doi.org/10.7554/eLife.04525.001 PMID:25647729

  7. Blue, green, orange, and red upconversion laser

    DOEpatents

    Xie, P.; Gosnell, T.R.

    1998-09-08

    A laser is disclosed for outputting visible light at the wavelengths of blue, green, orange and red light. This is accomplished through the doping of a substrate, such as an optical fiber or waveguide, with Pr{sup 3+} ions and Yb{sup 3+} ions. A light pump such as a diode laser is used to excite these ions into energy states which will produce lasing at the desired wavelengths. Tuning elements such as prisms and gratings can be employed to select desired wavelengths for output. 11 figs.

  8. Blue, green, orange, and red upconversion laser

    DOEpatents

    Xie, Ping; Gosnell, Timothy R.

    1998-01-01

    A laser for outputting visible light at the wavelengths of blue, green, orange and red light. This is accomplished through the doping of a substrate, such as an optical fiber or waveguide, with Pr.sup.3+ ions and Yb.sup.3+ ions. A light pump such as a diode laser is used to excite these ions into energy states which will produce lasing at the desired wavelengths. Tuning elements such as prisms and gratings can be employed to select desired wavelengths for output.

  9. Blue running of the primordial tensor spectrum

    SciTech Connect

    Gong, Jinn-Ouk

    2014-07-01

    We examine the possibility of positive spectral index of the power spectrum of the primordial tensor perturbation produced during inflation in the light of the detection of the B-mode polarization by the BICEP2 collaboration. We find a blue tilt is in general possible when the slow-roll parameter decays rapidly. We present two known examples in which a positive spectral index for the tensor power spectrum can be obtained. We also briefly discuss other consistency tests for further studies on inflationary dynamics.

  10. Blue compact dwarfs - Extreme dwarf irregular galaxies

    NASA Technical Reports Server (NTRS)

    Thuan, Trinh X.

    1987-01-01

    Observational data on the most extreme members of the irregular dwarf (dI) galaxy class, the blue compact dwarfs (BCDs), are characterized, reviewing the results of recent investigations. The properties of the young stellar population, the ionized gas, the older star population, and the gas and dust of BCDs are contrasted with those of other dIs; BCD morphology is illustrated with sample images; and the value of BCDs (as nearby 'young' chemically unevolved galaxies) for studies of galaxy formation, galactic evolution, and starburst triggering mechanisms is indicated.

  11. Slow-blue PanSTARRS transients

    NASA Astrophysics Data System (ADS)

    MacLeod, Chelsea L.; Bruce, Alastair; Lawrence, Andy; Ward, Martin; Collinson, James; Elvis, Martin; Gezari, Suvi; Smartt, Steven; Smith, Ken; Wright, Darryl; Fraser, Morgan

    2015-01-01

    Photometric and spectroscopic monitoring of 50 blue, nuclear "transients" in PanSTARRS-1 has revealed different types of extremely variable AGN. The majority show a gradual brightening by ~2 mag from the SDSS observation a decade ago and may represent a new class of AGN microlensed by foreground galaxies. Spectra from the William Herschel Telescope identify these as z~1 AGN with atypical spectroscopic properties. We present an analysis of their photometric and spectroscopic variability in an effort to constrain the detailed structure of the source AGN.

  12. Spectroscopic surveys of faint blue stars

    NASA Technical Reports Server (NTRS)

    Wegner, Gary; Boley, Forrest I.; Swanson, Steven R.; Mcmahan, Robert K.

    1987-01-01

    Spectroscopy of 450 faint blue stars obtained with the spectrograph and intensified Reticon scanner on the 1.3 m telescope at the McGraw Hill Observatory located at Kitt Peak are examined. The study is limited to objects brighter than V = 17.0 in magnitude. It is found that the relative numbers of objects such as white dwarfs, QSOs and CVs in the Kisco survey (Noguchi et al. 1980) is similar to that in the survey of Green et al., (1986).

  13. Maya Blue Paint: An Ancient Nanostructured Material

    PubMed

    Jose-Yacaman; Rendon; Arenas; Serra Puche MC

    1996-07-12

    Maya blue paint was often used in Mesoamerica. The origin of its color and its resistance to acids and biocorrosion have not been fully understood. High-resolution transmission electron microscopy, electron energy loss spectroscopy, and x-ray microanalysis studies of authentic samples show that palygorskite crystals in the paint form a superlattice that probably occurs as a result of mixing with indigo molecules. An amorphous silicate substrate contains inclusions of metal nanoparticles encapsulated in the substrate and oxide nanoparticles on the surface. The beautiful tone of the color is obtained only when both the particles and the superlattice are present. PMID:8662502

  14. Nonlinear Pulsation Modeling of Luminous Blue Variables

    SciTech Connect

    Despain, Kate M.; Guzik, Joyce A.; Cox, Arthur N.

    1997-12-31

    Using an updated version of the Ostlie and Cox (1993) nonlinear hydrodynamics code, we show the results of Luminous Blue Variable (LBV) envelope models based on evolution models of initial mass 50-80 M solar. including mass loss. The models use OPAL opacities, contain 60-120 Lagrangian zones, include time dependent convection, and are given an initial photospheric radial velocity amplitude of 1 km/sec. Our goal is to explain the reason for the LBV instability strip and suggest a cause for LBV outbursts observed in massive stars in our Galaxy as well as the LMC and SMC.

  15. Measuring star formation rates in blue galaxies

    NASA Technical Reports Server (NTRS)

    Gallagher, John S., III; Hunter, Deidre A.

    1987-01-01

    The problems associated with measurements of star formation rates in galaxies are briefly reviewed, and specific models are presented for determinations of current star formation rates from H alpha and Far Infrared (FIR) luminosities. The models are applied to a sample of optically blue irregular galaxies, and the results are discussed in terms of star forming histories. It appears likely that typical irregular galaxies are forming stars at nearly constant rates, although a few examples of systems with enhanced star forming activity are found among HII regions and luminous irregular galaxies.

  16. Blue Marble Space Institute essay contest

    NASA Astrophysics Data System (ADS)

    Wendel, JoAnna

    2014-04-01

    The Blue Marble Space Institute of Science, based in Seattle, Wash., is inviting college students to participate in its essay contest. Essays need to address the question, "In the next 100 years, how can human civilization prepare for the long-term changes to the Earth system that will occur over the coming millennium?" According to the institute, the purpose of the contest is "to stimulate creative thinking relating to space exploration and global issues by exploring how changes in the Earth system will affect humanity's future."

  17. Investigations of blue emitting phosphors for thermometry

    NASA Astrophysics Data System (ADS)

    Särner, Gustaf; Richter, Mattias; Aldén, Marcus

    2008-12-01

    Blue emitting phosphors are investigated and reported for possible use in thermometry. Currently reported thermographic phosphors in general have the drawback of long emission lifetimes obstructing the possibility to time gate for background discrimination. An additional problem is that many thermographic phosphors have emission in the red spectral region, making them vulnerable for black body radiation at high temperatures. This work reports the temperature sensitivity for nine phosphors considered suitable for accurate temperature measurements in harsh conditions both in single points and in two dimensions (2D).

  18. The curious conversion of Empire Blue Cross.

    PubMed

    Robinson, James C

    2003-01-01

    The for-profit conversion of Empire Blue Cross in New York challenges the case law and conventional policy wisdom that financial assets from formerly nonprofit organizations should be used to endow independent charitable foundations. The appropriation of Empire's assets by state government itself, and their subsequent deployment to subsidize health care institutions and repay political obligations, changes the conversion process from one that pits nonprofits against for-profits to one that pits private, nonprofit organizations against public-sector programs in the competition for new financial resources. PMID:12889758

  19. Development of novel Sol-Gel Indicators (SGI`s) for in-situ environmental measurements: Part 1, Program and a new pH Sol-Gel Indicator

    SciTech Connect

    Livingston, R.R.; Baylor, L.; Wicks, G.G.

    1992-11-03

    The feasibility of incorporating analytical indicators into a sol-gel glassy matrix and then coating substrates with this composite material has bee demonstrated. Substrates coated include paper, wood, glass, and the lens of an analytical probe. The first SRTC sol-gel indicator, comprising bromophenol blue dispersed in a silica matrix, was fabricated and successfully used to measure solution pH in the range of pH 3.0 to 7.5. material exhibited a quick response time, as measured by color changes both qualitatively and quantitatively, and the measuring device was reversible or reusable. Additional indicators with responses over other ranges as well as indicators sensitive to the presence of elements of interest, are also under development. The new SGI composites possess promising properties and an excellent potential for performing a variety important in-situ environmental measurements and area discussed in this report.

  20. Enhancing blue luminescence from Ce-doped ZnO nanophosphor by Li doping

    PubMed Central

    2014-01-01

    Undoped ZnO, Ce-doped ZnO, and (Li, Ce)-codoped ZnO nanophosphors were prepared by a sol-gel process. The effects of the additional doping with Li ions on the crystal structure, particle morphology, and luminescence properties of Ce-doped ZnO were investigated by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy, electron paramagnetic resonance spectroscopy and photoluminescence spectroscopy. The results indicate that the obtained samples are single phase, and a nanorod shaped morphology is observed for (Li, Ce)-codoping. Under excitation with 325 nm light, Ce-doped ZnO phosphors show an ultraviolet emission, a green emission, and a blue emission caused by Zn interstitials. The spectrum of the sample codoped with a proper Li concentration features two additional emissions that can be attributed to the Ce3+ ions. With the increase of the Li doping concentration, the Ce3+ blue luminescence of (Li, Ce)-codoped ZnO is obviously enhanced, which results not only from the increase of the Ce3+ ion concentration itself but also from the energy transfer from the ZnO host material to the Ce3+ ions. This enhancement reaches a maximum at a Li content of 0.02, and then decreases sharply due to the concentration quench. These nanophosphors may promise for application to the visible-light-emitting devices. PACS 78.55.Et; 81.07.Wx; 81.20.Fw PMID:25258604

  1. Ultraflexible organic amplifier with biocompatible gel electrodes.

    PubMed

    Sekitani, Tsuyoshi; Yokota, Tomoyuki; Kuribara, Kazunori; Kaltenbrunner, Martin; Fukushima, Takanori; Inoue, Yusuke; Sekino, Masaki; Isoyama, Takashi; Abe, Yusuke; Onodera, Hiroshi; Someya, Takao

    2016-01-01

    In vivo electronic monitoring systems are promising technology to obtain biosignals with high spatiotemporal resolution and sensitivity. Here we demonstrate the fabrication of a biocompatible highly conductive gel composite comprising multi-walled carbon nanotube-dispersed sheet with an aqueous hydrogel. This gel composite exhibits admittance of 100 mS cm(-2) and maintains high admittance even in a low-frequency range. On implantation into a living hypodermal tissue for 4 weeks, it showed a small foreign-body reaction compared with widely used metal electrodes. Capitalizing on the multi-functional gel composite, we fabricated an ultrathin and mechanically flexible organic active matrix amplifier on a 1.2-μm-thick polyethylene-naphthalate film to amplify (amplification factor: ∼200) weak biosignals. The composite was integrated to the amplifier to realize a direct lead epicardial electrocardiography that is easily spread over an uneven heart tissue. PMID:27125910

  2. Hardening and yielding in colloidal gels

    NASA Astrophysics Data System (ADS)

    Del Gado, Emanuela; Colombo, Jader; Bouzid, Mehdi

    Attractive colloidal gel networks are disordered elastic solids that can form even in extremely dilute particle suspensions. With interaction strengths comparable to the thermal energy, their stress-bearing network can locally restructure via breaking and reforming inter-particle bonds. We use molecular dynamics simulations of a model system to investigate the strain hardening and the yielding process. During shear start up protocol, the system exhibits strong localization of tensile stresses that may be released through the breaking and formation of new bonds. In this regime, the small amplitude oscillatory shear analysis shows that the storage and the loss modulus follow a power law behavior that are closely reminiscent of experimental observations. At large accumulated strains, the strain-induced reorganization of the gel may trigger flow heterogeneities and eventually lead to the yielding of the gel via a quasi brittle damage of its structure.

  3. Ultraflexible organic amplifier with biocompatible gel electrodes

    NASA Astrophysics Data System (ADS)

    Sekitani, Tsuyoshi; Yokota, Tomoyuki; Kuribara, Kazunori; Kaltenbrunner, Martin; Fukushima, Takanori; Inoue, Yusuke; Sekino, Masaki; Isoyama, Takashi; Abe, Yusuke; Onodera, Hiroshi; Someya, Takao

    2016-04-01

    In vivo electronic monitoring systems are promising technology to obtain biosignals with high spatiotemporal resolution and sensitivity. Here we demonstrate the fabrication of a biocompatible highly conductive gel composite comprising multi-walled carbon nanotube-dispersed sheet with an aqueous hydrogel. This gel composite exhibits admittance of 100 mS cm-2 and maintains high admittance even in a low-frequency range. On implantation into a living hypodermal tissue for 4 weeks, it showed a small foreign-body reaction compared with widely used metal electrodes. Capitalizing on the multi-functional gel composite, we fabricated an ultrathin and mechanically flexible organic active matrix amplifier on a 1.2-μm-thick polyethylene-naphthalate film to amplify (amplification factor: ~200) weak biosignals. The composite was integrated to the amplifier to realize a direct lead epicardial electrocardiography that is easily spread over an uneven heart tissue.

  4. Modeling polymer gel that strengthen under tension

    NASA Astrophysics Data System (ADS)

    Biswas, Santidan; Yashin, Victor V.; Balazs, Anna C.

    We develop a constitutive model of a responsive polymer gel, which can reversibly form additional crosslinks when under tension. We assume that the polymer chains incorporate the folded domains encompassing the reactive functional groups (cryptic sites). Under extension of the network, the domains unfold and expose the cryptic sites, which can then form labile bonds with the linker chains grafted to the network. Once the deformation is removed, the linkers detach from the cryptic sites, and unfolded domains go back to the folded configuration thus hiding the cryptic sites. The gel behavior under applied force is described by the equations of elasticity of the polymer network coupled to the kinetic equations for the folding and binding transitions. The developed model could be used for designing new polymer gel-based materials that exhibit self-strengthening in response to a mechanical action.

  5. Gel-Filled Holders For Ultrasonic Transducers

    NASA Technical Reports Server (NTRS)

    Companion, John A.

    1992-01-01

    In new technique, ultrasonic transducer embedded in rubbery, castable, low-loss gel to enable transducer to "look" into surface of test object or human body at any desired angle. Composed of solution of water and ethylene glycol in collagen matrix. Provides total contact of water bath, also used on bodies or objects too large for water baths, even if moving. Also provides look angles of poly(methyl methacrylate) angle block with potential of reduced acoustic impedance and refraction. Custom-tailored to task at hand, and gel sufficiently inexpensive to be discarded upon completion. Easy to couple ultrasound in and out of gel, minimizing losses and artifacts of other types of standoffs employed in ultrasonic testing.

  6. On the scattering properties of polyelectrolyte gels

    NASA Astrophysics Data System (ADS)

    Barrat, Jean-Louis; Joanny, Jean-François; Pincus, Phil

    1992-08-01

    We present a simple model for scattering properties of polyelectrolyte gels at swelling equilibrium. In the weak screening limit where the Debye-Hückel screening length is larger than the mesh size of the gel, the direct electrostatic interactions are negligible and the swelling is driven by the osmotic pressure of the counterions. The tension created by this pressure is transmitted through the crosslinks to the elastic chains which behave as isolated chains with an applied force at their end points. The structure factor of the gel can be split into a frozen component due to the average concentration heterogeneities and a thermodynamic component due to concentration fluctuations. The frozen component has a peak at a wavevector of the order of the mesh size of the gel, the thermodynamic component has a peak at a higher wavevector of the order of the inverse transverse radius of the chains. At infinite times the dynamic structure factor relaxes towards the frozen component of the static structure factor. In the limit of small wavevectors the relaxation is diffusive with a diffusion constant equal to the Stokes diffusion constant of the Pincus blobs of the stretched chains. The diffusion constant shows a minimum at a wavevector of the order of the inverse transverse radius of the chains. Nous présentons un modèle simple pour étudier la diffusion de rayonnement par des gels polylectrolytes à l'équilibre de gonflement. Dans la limite d'écrantage faible où la longueur d'écran de Debye-Hückel est plus grande que la maille du gel, les interactions électrostatiques directes sont négligeables et le gonflement est dû à la pression osmotique des contreions. La tension créée par cette pression est transmise par les noeuds du gel aux chaines élastiques qui se comportent comme des chaines isolées avec une force extérieure appliquée aux extrémités. Le facteur de structure du gel est la somme d'une composante gelée due aux hétérogénéités de concentration

  7. Writing in the granular gel medium

    PubMed Central

    Bhattacharjee, Tapomoy; Zehnder, Steven M.; Rowe, Kyle G.; Jain, Suhani; Nixon, Ryan M.; Sawyer, W. Gregory; Angelini, Thomas E.

    2015-01-01

    Gels made from soft microscale particles smoothly transition between the fluid and solid states, making them an ideal medium in which to create macroscopic structures with microscopic precision. While tracing out spatial paths with an injection tip, the granular gel fluidizes at the point of injection and then rapidly solidifies, trapping injected material in place. This physical approach to creating three-dimensional (3D) structures negates the effects of surface tension, gravity, and particle diffusion, allowing a limitless breadth of materials to be written. With this method, we used silicones, hydrogels, colloids, and living cells to create complex large aspect ratio 3D objects, thin closed shells, and hierarchically branched tubular networks. We crosslinked polymeric materials and removed them from the granular gel, whereas uncrosslinked particulate systems were left supported within the medium for long times. This approach can be immediately used in diverse areas, contributing to tissue engineering, flexible electronics, particle engineering, smart materials, and encapsulation technologies. PMID:26601274

  8. Preparation and characterization of hydrophobic superparamagnetic gel.

    SciTech Connect

    Liu, X.; Kaminski, M. D.; Guan, Y.; Chen, H.; Liu, H.; Rosengart, A. J.; Chemical Engineering; Univ. of Chicago; Pritzker School of Medicine; Chinese Academy of Sciences

    2006-01-01

    The present study describes the preparation and analysis of a highly concentrated hydrophobic oleic acid-coated magnetite gel. By contrast to conventional techniques to prepare magnetic fluids, herein the oleic acid was introduced as a reactant during the initial crystallization phase of magnetite that was obtained by the co-precipitation of Fe(II) and Fe(III) salts by addition of ammonium hydroxide. The resulting gelatinous hydrophobic magnetite was characterized in terms of morphology, particle size, magnetic properties, crystal structure, and hydrophobicity/hydrophilicity. This magnetic gel exhibited superparamagnetism with a saturation magnetization of 46.0 emu/g at room temperature and could be well dispersed both in polar and nonpolar carrier liquids. This protocol produced highly concentrated hydrophobic magnetic gel for biopolymer encapsulations.

  9. Characterizing tunable dynamics in an active gel

    NASA Astrophysics Data System (ADS)

    Henkin, Gil; Decamp, Stephen; Chen, Daniel; Dogic, Zvonimir

    2014-03-01

    We experimentally investigate dynamics of an active gel of bundled microtubules that is driven to far-from-equilibrium steady states by clusters of kinesin molecular motors. Upon the addition of ATP, the coordinated action of thousands of molecular motors drives this gel to an active, percolating state that persists for hours and is only limited by the stability of constituent proteins and the availability of the chemical fuel ATP. We extensively characterize how enhanced transport in emergent macroscopic flows depends on relevant molecular parameters, including ATP, motor, and depletant concentrations, microtubule concentration and length, as well as structure of the motor clusters. Our results show that the properties and dynamics of this active isotropic gel are highly tunable, suggesting that this is an ideal system for studying the behavior of active materials.

  10. Writing in the granular gel medium.

    PubMed

    Bhattacharjee, Tapomoy; Zehnder, Steven M; Rowe, Kyle G; Jain, Suhani; Nixon, Ryan M; Sawyer, W Gregory; Angelini, Thomas E

    2015-09-01

    Gels made from soft microscale particles smoothly transition between the fluid and solid states, making them an ideal medium in which to create macroscopic structures with microscopic precision. While tracing out spatial paths with an injection tip, the granular gel fluidizes at the point of injection and then rapidly solidifies, trapping injected material in place. This physical approach to creating three-dimensional (3D) structures negates the effects of surface tension, gravity, and particle diffusion, allowing a limitless breadth of materials to be written. With this method, we used silicones, hydrogels, colloids, and living cells to create complex large aspect ratio 3D objects, thin closed shells, and hierarchically branched tubular networks. We crosslinked polymeric materials and removed them from the granular gel, whereas uncrosslinked particulate systems were left supported within the medium for long times. This approach can be immediately used in diverse areas, contributing to tissue engineering, flexible electronics, particle engineering, smart materials, and encapsulation technologies. PMID:26601274

  11. An anion channel in Arabidopsis hypocotyls activated by blue light.

    PubMed Central

    Cho, M H; Spalding, E P

    1996-01-01

    A rapid, transient depolarization of the plasma membrane in seedling stems is one of the earliest effects of blue light detected in plants. It appears to play a role in transducing blue light into inhibition of hypocotyl (stem) elongation, and perhaps other responses. The possibility that activation of a Cl- conductance is part of the depolarization mechanism was raised previously and addressed here. By patch clamping hypocotyl cells isolated from dark-grown (etiolated) Arabidopsis seedlings, blue light was found to activate an anion channel residing at the plasma membrane. An anion-channel blocker commonly known as NPPB 15-nitro-2-(3-phenylpropylamino)-benzoic acid] potently and reversibly blocked this anion channel. NPPB also blocked the blue-light-induced depolarization in vivo and decreased the inhibitory effect of blue light on hypocotyl elongation. These results indicate that activation of this anion channel plays a role in transducing blue light into growth inhibition. PMID:8755616

  12. An anion channel in Arabidopsis hypocotyls activated by blue light

    NASA Technical Reports Server (NTRS)

    Cho, M. H.; Spalding, E. P.; Evans, M. L. (Principal Investigator)

    1996-01-01

    A rapid, transient depolarization of the plasma membrane in seedling stems is one of the earliest effects of blue light detected in plants. It appears to play a role in transducing blue light into inhibition of hypocotyl (stem) elongation, and perhaps other responses. The possibility that activation of a Cl- conductance is part of the depolarization mechanism was raised previously and addressed here. By patch clamping hypocotyl cells isolated from dark-grown (etiolated) Arabidopsis seedlings, blue light was found to activate an anion channel residing at the plasma membrane. An anion-channel blocker commonly known as NPPB 15-nitro-2-(3-phenylpropylamino)-benzoic acid] potently and reversibly blocked this anion channel. NPPB also blocked the blue-light-induced depolarization in vivo and decreased the inhibitory effect of blue light on hypocotyl elongation. These results indicate that activation of this anion channel plays a role in transducing blue light into growth inhibition.

  13. Differential migration of Blue Grouse in Colorado

    USGS Publications Warehouse

    Cade, Brian S.; Hoffman, Richard W.

    1993-01-01

    We examined migration of adult Blue Grouse (Dendragapus obscurus) in north-central Colorado by radio tracking 13 males and 19 females. Elevational changes associated with movements to winter areas were greater for males (median = 488 m, range = 183-671 m) than females (median = 122 m, range = -61-760 m). Males (median = 10.5 km, range = 1.0-29.4 km) also moved farther than females (median = 1.0 km, range = 0.1-28.0 km), resulting in partial segregation of sexes during winter. Directional orientation of movements to wintering areas was nonrandom for long-distance (>3 km) migrants. Median elevational change (122 m) and distance (0.6 km) between the first-winter and first-breeding areas for seven juvenile females were similar to movements of adult females. Males (median = 7 July) departed breeding areas earlier than females (median = 11 August), but arrived (median = 14 October) on winter areas about the same time as females (median = 23 October). Both sexes exhibited fidelity to winter areas. The average distance between winter locations ranged from 94 to 312 m (median = 135 m) for 11 radio-marked adults, suggesting Blue Grouse were sedentary on their winter ranges.

  14. Maya blue: a clay-organic pigment?

    PubMed

    Van Olphen, H

    1966-11-01

    Maya Blue, a pigment used by the Mayas in Yucatan, is remarkably stable: the color is not destroyed by hot concentrated mineral acids or by heating to about 250 degrees C. The principal constituent is the colorless mineral attapulgite. It is proposed that the pigment is an adsorption complex of attapulgite and natural indigo; a synthetic equivalent may be prepared from attapulgite and either indoxylester or indigo, or by applying the vat-dyeing technique, with reduced indigo.The low dye content of the pigment (less than 0.5 percent) indicates that the dye is absorbed only on the external surfaces of the attapulgite particles and not throughout the channels in their structures. The complex as such is not stable to acids, but the stability displayed by Maya Blue is achieved simply by heating the complex to from 75 degrees to 150 degrees C for several days. An analogous stable pigment can be prepared from sepiolite and indigo. No stable pigments could be prepared from clays with platelike structures or from zeolites. PMID:17778806

  15. Phenothiazinium photosensitisers XI. Improved toluidine blue photoantimicrobials.

    PubMed

    Wainwright, Mark; O'Kane, Ciara; Rawthore, Sophie

    2016-07-01

    The phenothiazinium derivative toluidine blue O (TBO) is widely employed as a photoantimicrobial agent in clinical trialling, particularly in dentistry. However, its activity against a range of pathogenic microbial species is not significantly different to that of the standard photoantimicrobial methylene blue. In the current study, derivatives of TBO with varying hydrocarbon substitution in chromophore position 2 were synthesised via the established anilinethiosulphonic route, using the mild oxidant silver(II) carbonate to allow substituent preservation. The resulting series of analogues demonstrated the expected increases in visible absorption wavelength and lipophilicity with increasing hydrocarbon content, as well as decreased aggregation for derivatives with bulkier substituents, and all produced singlet oxygen on illumination in vitro. Screening against a range of bacterial and fungal pathogens relevant to infection control showed remarkable increases in activity relative to the parent compound, particularly against the clinically important Gram-negative bacterium Pseudomonas aeruginosa. In addition, in order to demonstrate clinical relevance, the photoactivities of the new derivatives against microbial targets were compared to conventional antibacterial and antifungal drugs, as well as biocides commonly used for local disinfection. Activity here was also generally greater than that of the conventional agents used for comparison, considerably so relative to the local disinfectant agents. PMID:27093001

  16. Pulsations and outbursts of luminous blue variables

    SciTech Connect

    Cox, A.N.; Guzik, J.A.; Soukup, M.S.; Despain, K.M.

    1997-06-01

    We propose an outburst mechanism for the most luminous stars in our and other galaxies. These million solar luminosity stars, with masses (after earlier mass loss) of between 20 and maybe 70 solar masses, are pulsationally unstable for both radial and low-degree nonradial modes. Some of these modes are ``strange,`` meaning mostly that the pulsations are concentrated near the stellar surface and have very rapid growth rates in linear theory. The pulsation driving is by both the high iron line opacity (near 150,000 K) and the helium opacity (near 30,000 K) kappa effects. Periods range from 5 to 40 days. Depending on the composition, pulsations periodically produce luminosities above the Eddington limit for deep layers. The radiative luminosity creates an outward push that readily eases the very low gamma envelope to very large outburst radii. A key point is that a super-Eddington luminosity cannot be taken up by the sluggish convection rapidly enough to prevent an outward acceleration of much of the envelope. As the helium abundance in the envelope stellar material increases by ordinary wind mass loss and the luminous blue variable outbursts, the opacity in the deep pulsation driving layers decreases. This makes the current Eddington luminosity even higher so that pulsations can then no longer give radiative luminosities exceeding the limit. For the lower mass and luminosity luminous blue variables there is considerably less iron line opacity driving, and pulsations are almost all caused by the helium ionization kappa effect.

  17. Raphael Meldola, his blue and his times.

    PubMed

    Travis, A S

    2012-05-01

    Raphael Meldola (1849-1915), English industrial and academic chemist, spectroscopist, naturalist, educator and lobbyist for science, is today almost a forgotten scientist whose life is celebrated only with a medal awarded by the Royal Society of Chemistry that honors achievement by younger chemists. In the 1870-80s, however, he invented a number of important synthetic dyestuffs including the cotton dyes isamine blue and Meldola's blue, and also naphthol green B, all of which have had application in biology and medicine. I describe here the early emergence of the synthetic dye industry, the first science-based industry, Meldola's role in its development, and his own inventions. Meldola's wide ranging achievements in science led to appointments as president of important professional scientific and manufacturers' societies. He was a fervent disciple of natural selection, a correspondent of Charles Darwin, and a prominent 19(th)-century neo-Darwinian. In 1886, drawing on analogies with evolutionary theory, he warned the British that neglect of science, particularly chemistry, would lead to industrial decline and even extinction, though his message generally was ignored, at least until 1914. PMID:22148999

  18. Blue LEDs feasibility for tissue fluorescence analysis

    NASA Astrophysics Data System (ADS)

    Dets, Sergiy M.; Denisov, Nikolay A.

    2000-04-01

    We considered the limited number of light-induced fluorescence applications for marketed ultra-bright blue LEDs where they can compete with versatile laser sources. Satisfactory optical output and miniature size as well as low power consumption of blue LEDs emitting at 470 nm allow to consider them as a promising alternatives to metal vapor or gas lasers used in many expires LIF applications. Available to authors LEDs form Hewlett-Packard, Micro Electronics Corp., Nichia Chemical Industries Ltd. and Toyoda Gosei Co. were tested to comply with demands to a tissue excitation source for portable spectroscopes. The optical performance of LEDs has shown that selected group of InGaN LEDs could be successfully used for that. The miniature illuminator that includes LED, focusing condenser, filter set and distal fiberoptic light concentrator was designed and tested in conjunction with portable CCD- equipped spectroscope. Operating in dark condition the proposed LED illuminator provides the level of fluorescence signal sufficient to detect spectral abnormalities in human Caucasian skin and excised gastrointestinal samples. All tissue autofluorescence data taken under LED illumination were compared with readings under He-Cd laser excitation and showed a good match. A new diagnostic designs based on LEDs were considered for clinical use.

  19. Structural and optical characterization of CdSe nanocrystallites/rare earth ions in sol gel glasses

    NASA Astrophysics Data System (ADS)

    Jose, Gijo; Joseph, Cyriac; Ittyachen, M. A.; Unnikrishnan, N. V.

    2007-07-01

    Sol-gel method is used to prepare semiconductor cadmium selenide nanocrystallites together with europium and terbium ions in silica matrix. From the electron diffraction pattern in the transmission electron micrograph (TEM), the plane distances (d) were estimated to be 1.072 Å, 1.233 Å and 2.149 Å, which match the (2 1 4), (3 0 0) and (1 1 0) planes of bulk CdSe. The intensity of characteristic red emission of Europium (Eu3+) and green emission of Terbium (Tb3+) ions increases considerably in the presence of CdSe particles. The blue emission is prominent in the glass samples in the gel stage. The purity of the colors are measured using the Commission Internationale de Eclairage (CIE) color coordinate diagram and is found to be 100% for RED and GREEN.

  20. Dye-sensitized solar cell with natural gel polymer electrolytes and f-MWCNT as counter-electrode

    NASA Astrophysics Data System (ADS)

    Nwanya, A. C.; Amaechi, C. I.; Ekwealor, A. B. C.; Osuji, R. U.; Maaza, M.; Ezema, F. I.

    2015-05-01

    Samples of DSSCs were made with gel polymer electrolytes using agar, gelatin and DNA as the polymer hosts. Anthocyanine dye from Hildegardia barteri flower is used to sensitize the TiO2 electrode, and the spectrum of the dye indicates strong absorptions in the blue region of the solar spectrum. The XRD pattern of the TiO2 shows that the adsorption of the dye did not affect the crystallinity of the electrode. The f-MWCNT indicates graphite structure of the MWCNTs were acid oxidized without significant damage. Efficiencies of 3.38 and 0.1% were obtained using gelatin and DNA gel polymer electrolytes, respectively, for the fabricated dye-sensitized solar cells.

  1. Reduction of gas and water permeabilities using gels

    SciTech Connect

    Seright, R.S.

    1995-05-01

    The authors investigated how different types of gels reduce permeability to water and gases in porous rock. Five types of gels were studied, including (1) a ``weak`` resorcinol-formaldehyde gel, (2) a ``strong`` resorcinol-formaldehyde gel, (3) a Cr(III)-xanthan gel, (4) a Cr(III)-acetate-HPAM gel, and (5) a colloidal-silica gel. For all gels, extensive coreflood experiments were performed to assess the permeability-reduction characteristics and the stability to repeated water-alternating-gas (WAG) cycles. Studies were performed at pressures up to 1,500 psi using either nitrogen or carbon dioxide as the compressed gas. They developed a coreflood apparatus with an inline high-pressure spectrophotometer that allowed tracer studies to be performed without depressurizing the core. They noted several analogies between the results reported here and those observed during a parallel study of the effects of gel on oil and water permeabilities.

  2. Polycrystalline BiFeO3 thin film synthesized via sol-gel assisted spin coating technique for photosensitive application

    NASA Astrophysics Data System (ADS)

    Bogle, K. A.; Narwade, R. D.; Phatangare, A. B.; Dahiwale, S. S.; Mahabole, M. P.; Khairnar, R. S.

    2016-05-01

    We are reporting photosensitivity property of BiFeO3 thin film under optical illumination. The thin film used for photosensitivity work was fabricated via sol-gel assisted spin coating technique. I-V measurements on the Cu/BiFeO3/Al structure under dark condition show a good rectifying property and show dramatic blue shit in threshold voltage under optical illumination. The microstructure, morphology and elemental analysis of the films were characterized by using XRD, UV-Vis, FTIR, SEM and EDS.

  3. Pouring and running a protein gel by reusing commercial cassettes.

    PubMed

    Hwang, Alexander C; Grey, Paris H; Cuddy, Katrina; Oppenheimer, David G

    2012-01-01

    The evaluation of proteins using sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE) analysis is a common technique used by biochemistry and molecular biology researchers. For laboratories that perform daily analyses of proteins, the cost of commercially available polyacrylamide gels (~$10/gel) can be considerable over time. To mitigate this cost, some researchers prepare their own polyacrylamide gels. Traditional methods of pouring these gels typically utilize specialized equipment and glass gel plates that can be expensive and preclude pouring many gels and storing them for future use. Furthermore, handling of glass plates during cleaning or gel pouring can result in accidental breakage creating a safety hazard, which may preclude their use in undergraduate laboratory classes. Our protocol demonstrates how to pour multiple protein gels simultaneously by recycling Invitrogen Nupage Novex minigel cassettes, and inexpensive materials purchased at a home improvement store. This economical and streamlined method includes a way to store the gels at 4°C for a few weeks. By re-using the plastic gel cassettes from commercially available gels, labs that run frequent protein gels can save significant costs and help the environment. In addition, plastic gel cassettes are extremely resistant to breakage, which makes them ideal for undergraduate laboratory classrooms. PMID:22349047

  4. Twisted bilayer blue phosphorene: A direct band gap semiconductor

    NASA Astrophysics Data System (ADS)

    Ospina, D. A.; Duque, C. A.; Correa, J. D.; Suárez Morell, Eric

    2016-09-01

    We report that two rotated layers of blue phosphorene behave as a direct band gap semiconductor. The optical spectrum shows absorption peaks in the visible region of the spectrum and in addition the energy of these peaks can be tuned with the rotational angle. These findings makes twisted bilayer blue phosphorene a strong candidate as a solar cell or photodetection device. Our results are based on ab initio calculations of several rotated blue phosphorene layers.

  5. Synthesis of CdS/CdSe core/shell ultra small nanostructures using new microwave assisted ultrasonic sol gel route

    SciTech Connect

    Goswami, Y. C. Kumar, Vijay; Sharma, Ranjana; Singh, Rajeev

    2014-04-24

    Core-shell CdS/CdSe nanostructures have been synthesized by new microwave assisted ultrasonic sol gel route. The solution was obtained by dissolving cadmium acetate and Thiourea in the molar ratio 1:1 in Triethlioamine. The solution was Ultrasonically irradiated by Ultrasonic crystal at 40 Hz for 3 hours at 70°C. The sol was kept for another 24 hours for gel formation. Selenium dioxide was used as a selenium source and added separately. The gel was spin coated on Quartz and Glass slides followed by microwave heat treatment. The samples were characterized by structural morphological and optical characterization. XRD studies confirm the zinc blende phase of the CdS nanoparticles. The mean nanocrystal sizes calculated using Scherrer equation is ∼1.2nm. Optical studies show the strong blue shift in the spectra due to very small size of the nanocrystals. TEM and HRTEM confirm the formation of core shell structures.

  6. Dynamic Light Scattering From Colloidal Gels

    NASA Technical Reports Server (NTRS)

    Krall, A. H.; Weitz, David A.

    1996-01-01

    We present a brief, preliminary account of the interpretation of dynamic light scattering from fractal colloidal gels. For small scattering angles, and for high initial colloid particle volume fractions, the correlation functions exhibit arrested decay, reflecting the non-ergodic nature of these systems and allowing us to directly determine the elastic modulus of the gels. For smaller initial volume fractions, the correlation functions decay completely. In all cases, the initial decay is not exponential, but is instead described by a stretched exponential. We summarize the principles of a model that accounts for these data and discuss the scaling behavior of the measured parameters.

  7. Neutron detector using sol-gel absorber

    SciTech Connect

    Hiller, J.M.; Wallace, S.A.; Dai, S.

    1999-10-26

    An neutron detector composed of fissionable material having ions of lithium, uranium, thorium, plutonium, or neptunium, contained within a glass film fabricated using a sol-gel method combined with a particle detector is disclosed. When the glass film is bombarded with neutrons, the fissionable material emits fission particles and electrons. Prompt emitting activated elements yielding a high energy electron contained within a sol-gel glass film in combination with a particle detector is also disclosed. The emissions resulting from neutron bombardment can then be detected using standard UV and particle detection methods well known in the art, such as microchannel plates, channeltrons, and silicon avalanche photodiodes.

  8. Neutron detector using sol-gel absorber

    DOEpatents

    Hiller, John M.; Wallace, Steven A.; Dai, Sheng

    1999-01-01

    An neutron detector composed of fissionable material having ions of lithium, uranium, thorium, plutonium, or neptunium, contained within a glass film fabricated using a sol-gel method combined with a particle detector is disclosed. When the glass film is bombarded with neutrons, the fissionable material emits fission particles and electrons. Prompt emitting activated elements yielding a high energy electron contained within a sol-gel glass film in combination with a particle detector is also disclosed. The emissions resulting from neutron bombardment can then be detected using standard UV and particle detection methods well known in the art, such as microchannel plates, channeltrons, and silicon avalanche photodiodes.

  9. Hybrid sol-gel optical materials

    DOEpatents

    Zeigler, J.M.

    1993-04-20

    Hybrid sol-gel materials comprise silicate sols cross-linked with linear polysilane, polygermane, or poly(silane-germane). The sol-gel materials are useful as optical identifiers in tagging and verification applications and, in a different aspect, as stable, visible light transparent non-linear optical materials. Methyl or phenyl silicones, polyaryl sulfides, polyaryl ethers, and rubbery polysilanes may be used in addition to the linear polysilane. The linear polymers cross-link with the sol to form a matrix having high optical transparency, resistance to thermooxidative aging, adherence to a variety of substrates, brittleness, and a resistance to cracking during thermal cycling.

  10. Hybrid sol-gel optical materials

    DOEpatents

    Zeigler, John M.

    1993-01-01

    Hybrid sol-gel materials comprise silicate sols cross-linked with linear polysilane, polygermane, or poly(silane-germane). The sol-gel materials are useful as optical identifiers in tagging and verification applications and, in a different aspect, as stable, visible light transparent non-linear optical materials. Methyl or phenyl silicones, polyaryl sulfides, polyaryl ethers, and rubbery polysilanes may be used in addition to the linear polysilane. The linear polymers cross-link with the sol to form a matrix having high optical transparency, resistance to thermooxidative aging, adherence to a variety of substrates, brittleness, and a resistance to cracking during thermal cycling.

  11. Hybrid sol-gel optical materials

    DOEpatents

    Zeigler, John M.

    1992-01-01

    Hybrid sol-gel materials comprise silicate sols cross-linked with linear polysilane, polygermane, or poly(silane-germane). The sol-gel materials are useful as optical identifiers in tagging and verification applications and, in a different aspect, as stable, visible light transparent non-linear optical materials. Methyl or phenyl silicones, polyaryl sulfides, polyaryl ethers, and rubbery polysilanes may be used in addition to the linear polysilane. The linear polymers cross-link with the sol to form a matrix having high optical transparency, resistance to thermooxidative aging, adherence to a variety of substrates, brittleness, and a resistance to cracking during thermal cycling.

  12. Alignment and nonlinear elasticity in biopolymer gels

    NASA Astrophysics Data System (ADS)

    Feng, Jingchen; Levine, Herbert; Mao, Xiaoming; Sander, Leonard M.

    2015-04-01

    We present a Landau-type theory for the nonlinear elasticity of biopolymer gels with a part of the order parameter describing induced nematic order of fibers in the gel. We attribute the nonlinear elastic behavior of these materials to fiber alignment induced by strain. We suggest an application to contact guidance of cell motility in tissue. We compare our theory to simulation of a disordered lattice model for biopolymers. We treat homogeneous deformations such as simple shear, hydrostatic expansion, and simple extension, and obtain good agreement between theory and simulation. We also consider a localized perturbation which is a simple model for a contracting cell in a medium.

  13. Electroactive polymer gels based on epoxy resin

    NASA Astrophysics Data System (ADS)

    Samui, A. B.; Jayakumar, S.; Jayalakshmi, C. G.; Pandey, K.; Sivaraman, P.

    2007-04-01

    Five types of epoxy gels have been synthesized from common epoxy resins and hardeners. Fumed silica and nanoclay, respectively, were used as fillers and butyl methacrylate/acrylamide were used as monomer(s) for making interpenetrating polymer networks (IPNs) in three compositions. Swelling study, tensile property evaluation, dynamic mechanical thermal analysis, thermo-gravimetric analysis, scanning electron microscopy and electroactive property evaluation were done. The gels have sufficient mechanical strength and the time taken for bending to 20° was found to be 22 min for forward bias whereas it was just 12 min for reverse bias.

  14. Simple cloud chambers using gel ice packs

    NASA Astrophysics Data System (ADS)

    Kamata, Masahiro; Kubota, Miki

    2012-07-01

    Although cloud chambers are highly regarded as teaching aids for radiation education, school teachers have difficulty in using cloud chambers because they have to prepare dry ice or liquid nitrogen before the experiment. We developed a very simple and inexpensive cloud chamber that uses the contents of gel ice packs which can substitute for dry ice or liquid nitrogen. The gel can be frozen in normal domestic freezers, and can be used repeatedly by re-freezing. The tracks of alpha-ray particles can be observed continuously for about 20 min, and the operation is simple and easy.

  15. Aggregation-structure-elasticity relationship of gels

    NASA Astrophysics Data System (ADS)

    Ma, Hang-Shing

    Aerogel is a mesoporous, low-density material which is desirable for applications like thermal insulation and low-k interlayer dielectric. However, its lack of mechanical integrity hinders its development. Experiments have shown that aerogels exhibit a scaling relationship E ∝ rho m between modulus E and density rho, with the exponent m usually between 3 and 4. The objective of the dissertation is to use computer modeling to understand how the random aggregation process accounts for the fractal structure and the compliant nature of aerogels. Model gels were created by the diffusion-limited cluster-cluster aggregation (DLCA), which simulates random aggregation leading to the sol-gel transition. Then each resulting structure was modeled as an elastic beam network and numerically compressed using the finite element method (FEM). Analyses showed that the DLCA gels reproduced the scaling relationship after trimming the non-contributive dangling branches from the mechanically efficient looped networks. The dangling bond deflection (DEF) model was therefore developed to model the random rotational movement of the dangling branches and the subsequent loop structure formation. Model gels with extensive loops and negligible dangling branches were simulated by combining the DLCA and DEF models. Representation of the aerogel networks by the DLCADEF models was validated for the resemblance of the fractal geometry and elastic behavior. The lack of mechanical integrity in aerogels is a natural consequence of the random aggregation and the resulting fractal structure. Fractal clusters are created in the early stage of aggregation, each of which is characterized by a dense core and sparse perimeter. These clusters grow in size until they percolate at the gel point by knitting together at the perimeters. The gel structure possesses a "blob-and-link" architecture, with the blobs representing the rigid cores of the fractal clusters, and the links corresponding to the tenuous chains

  16. The Return of the Blue Butterfly

    NASA Astrophysics Data System (ADS)

    Santos, Anabela

    2014-05-01

    The Return of the Blue Butterfly The English writer Charles Dickens once wrote: "I only ask to be free. The butterflies are free". But are they really? The work that I performed with a group of students from 8th grade, had a starting point of climate change and the implications it has on ecosystems. Joining the passion I have for butterflies, I realized that they are also in danger of extinction due to these climatic effects. Thus, it was easy to seduce my students wanting to know more. Luckily I found Dr. Paula Seixas Arnaldo, a researcher at the University of Trás-os-Montes and Alto Douro, who has worked on butterflies and precisely investigated this issue. Portugal is the southern limit of butterfly-blue (Phengaris alcon), and has been many years in the red book of endangered species. Butterfly-blue is very demanding of their habitat, and disappears very easily if ideal conditions are not satisfied. Increased fragmentation of landscapes and degradation of suitable habitats, are considered the greatest challenges of the conservation of Phengaris butterfly in Portugal. In recent decades, climate change has also changed butterfly-blue spatial distribution with a movement of the species northward to colder locations, and dispersion in latitude. Butterflies of Europe must escape to the North because of the heat. Dr. Paula Seixas Arnaldo and her research team began a project, completed in December 2013, wanted to preserve and restore priority habitats recognized by the European Union to help species in danger of disappearing with increasing temperature. The blue butterfly is extremely important because it is a key indicator of the quality of these habitats. In the field, the butterflies are monitored to collect all possible data in order to identify the key species. Butterflies start flying in early July and cease in late August. Mating takes about an hour and occurs in the first days of life. The gentian-peat (Gentiana pneumonanthe) serves as the host plant for

  17. Chemical sensing of copper phthalocyanine sol-gel glass through organic vapors

    SciTech Connect

    Ridhi, R.; Gawri, Isha; Abbas, Saeed J.; Saini, G. S. S.; Tripathi, S. K.

    2015-05-15

    The sensitivities of metallophthalocyanine to vapor phase electron donors has gained significance in many areas and disciplines due to their sensing properties and ease of operation. In the present study the interaction mechanism of organic vapors in Copper Phthalocyanine (CuPc) sol-gel glass has been studied. The interaction mechanism is affected by many factors like morphology, electrical or optical properties of film. CuPc sol-gel glass has been synthesized using chemical route sol-gel method. Its structural characterization was conducted using XRD and the amorphous nature of the silicate glass was observed with characteristic α polymorph phase of CuPc at around 6.64° with 13.30Å interplanar spacing. The size of the particle as determined using Debbye Scherre’s formula comes out around 15.5 nm. The presence of α phase of CuPc was confirmed using FTIR with the appearance of crystal parameter marker band at 787 cm-1. Apart from this A2u and Eu symmetry bands of CuPc have also been observed. The UV absorption spectrum of CuPc exhibits absorption peaks owing to π→ π* and n→ π* transitions. A blue shift in the prepared CuPc glass has been observed as compared to the dopant CuPc salt indicating increase of band gap. A split in B (Soret) band and Q band appears as observed with the help of Lorentzian fitting. CuPc sol gel glass has been exposed with chemical vapors of Methanol, Benzene and Bromine individually and the electrical measurements have been carried out. These measurements show the variation in conductivity and the interaction mechanism has been analyzed.

  18. Chemical sensing of copper phthalocyanine sol-gel glass through organic vapors

    NASA Astrophysics Data System (ADS)

    Ridhi, R.; Gawri, Isha; Abbas, Saeed J.; Saini, G. S. S.; Tripathi, S. K.

    2015-05-01

    The sensitivities of metallophthalocyanine to vapor phase electron donors has gained significance in many areas and disciplines due to their sensing properties and ease of operation. In the present study the interaction mechanism of organic vapors in Copper Phthalocyanine (CuPc) sol-gel glass has been studied. The interaction mechanism is affected by many factors like morphology, electrical or optical properties of film. CuPc sol-gel glass has been synthesized using chemical route sol-gel method. Its structural characterization was conducted using XRD and the amorphous nature of the silicate glass was observed with characteristic α polymorph phase of CuPc at around 6.64˚ with 13.30Å interplanar spacing. The size of the particle as determined using Debbye Scherre's formula comes out around 15.5 nm. The presence of α phase of CuPc was confirmed using FTIR with the appearance of crystal parameter marker band at 787 cm-1. Apart from this A2u and Eu symmetry bands of CuPc have also been observed. The UV absorption spectrum of CuPc exhibits absorption peaks owing to π→ π* and n→ π* transitions. A blue shift in the prepared CuPc glass has been observed as compared to the dopant CuPc salt indicating increase of band gap. A split in B (Soret) band and Q band appears as observed with the help of Lorentzian fitting. CuPc sol gel glass has been exposed with chemical vapors of Methanol, Benzene and Bromine individually and the electrical measurements have been carried out. These measurements show the variation in conductivity and the interaction mechanism has been analyzed.

  19. 2% Lidocaine gel or plain lubricating gel: Which one should be used in male flexible cystoscopy?

    PubMed Central

    Akkoç, Ali; Kartalmış, Mahir; Aydın, Cemil; Topaktaş, Ramazan; Altın, Selçuk; Aykaç, Aykut

    2016-01-01

    Objective To investigate and compare the effects on pain of intraurethral 2% lidocaine gel and plain lubricating gel in male patients underwent flexible cystoscopy. Material and methods The data of 220 male patients who underwent flexible cystoscopy between March 2012 and August 2014 were retrospectively analized. The patients were divided into 2 groups according to using intraurethral gel types. Group I included 120 patients who were underwent flexible cystoscopy with 2% lidocaine gel and Group II was consisted from 100 patients who underwent flexible cystoscopy with plain lubricating gel. The groups were compared according to postprocedure data including pain score, procedure time and age of patients. Results The mean age of the patients in Group I was 50.02±11.87 years while that in Group II was 52.03±13.37 years (p=0.492). The mean procedure times were 6.02±0.787 and 6.28±0.689 minutes in Group I and Group II respectively (p=0.061). Pain perception scores were not statistically different between the groups (Group I: 3.10±0.980, Group II: 3.34±0.789, p=0.132). Conclusion Use of intraurethral 2% lidocaine gel has no advantage over plain lubricating gel in regard to pain control during flexible cystoscopy in men. PMID:27274894

  20. Gel-expanded to gel-condensed transition in neurofilament networks revealed by direct force measurements

    NASA Astrophysics Data System (ADS)

    Beck, Roy; Deek, Joanna; Jones, Jayna B.; Safinya, Cyrus R.

    2010-01-01

    Neurofilaments (NF)-the principal cytoskeletal constituent of myelinated axons in vertebrates-consist of three molecular-weight subunit proteins NF-L (low), NF-M (medium) and NF-H (high), assembled to form mature filaments with protruding unstructured C-terminus side arms. Liquid-crystal gel networks of side-arm-mediated neurofilament assemblies have a key role in the mechanical stability of neuronal processes. Disruptions of the neurofilament network, owing to neurofilament over-accumulation or incorrect side-arm interactions, are a hallmark of motor-neuron diseases including amyotrophic lateral sclerosis. Using synchrotron X-ray scattering, we report on a direct measurement of forces in reconstituted neurofilament gels under osmotic pressure (P). With increasing pressure near physiological salt and average phosphorylation conditions, NF-LMH, comprising the three subunits near in vivo composition, or NF-LH gels, undergo for P>Pc~10kPa, an abrupt non-reversible gel-expanded to gel-condensed transition. The transition indicates side-arm-mediated attractions between neurofilaments consistent with an electrostatic model of interpenetrating chains. In contrast, NF-LM gels remain in a collapsed state for Pgel-condensed state at P>Pc. These findings, which delineate the distinct roles of NF-M and NF-H in regulating neurofilament interactions, shed light on possible mechanisms for disruptions of optimal mechanical network properties.

  1. Effect of gel matrix confinement on the solvent dynamics in supramolecular gels.

    PubMed

    Kowalczuk, Joanna; Rachocki, Adam; Bielejewski, Michał; Tritt-Goc, Jadwiga

    2016-06-15

    Supramolecular gels formed by the sugar gelator of methyl-4,6-O-(p-nitrobenzylidene)-α-d-glucopyranoside (1) with 1,3-propanediol (PG) and 1-butanol (BU) were prepared with different gelator concentrations. The solvent dynamics within gels, characterized by the diffusion coefficient (D) and the spin-lattice relaxation time (T1), was the subject of NMR diffusometry and relaxometry studies. The diffusion was studied as a function of diffusion time and gelator concentrations. The relaxation time was measured as a function of Larmor frequency. The decrease of the diffusion coefficient was observed as a function of diffusion time for both gels and for all studied gelator concentrations. It is indicative of the confinement effect due to the geometrical restrictions of the gel matrix. The relaxation data for PG solvent confined in 1/PG gel revealed the low frequency dispersion (in kHz region) which is a fingerprint of a specific interaction experienced by PG solvents in the presence of the rigid structure of gelator 1 aggregates. The relaxation model, well known from the interpretation of liquid confined in nanopores as reorientations mediated by translational displacements (RMTD), was successfully applied to analyze the data of studied solvents confined in matrices of supramolecular gels. The microstructures of gel matrices were imaged by Polarized Microscopy. PMID:27003500

  2. Free forming of the gel by 3D gel printer SWIM-ER

    NASA Astrophysics Data System (ADS)

    Okada, Koji; Tase, Taishi; Saito, Azusa; Makino, Masato; Gong, Jin; Kawakami, Masaru; Furukawa, Hidemitsu

    2015-04-01

    Gels, soft and wet materials, have unique properties such as material permeability, biocompatibility and low friction, which are hardly found in hard and dry materials. These superior characteristics of hydrogels promise to expand the medical applications. In recent years, the optical 3D gel printer named SWIM-ER (Soft and Wet Industrial - Easy Realizer) was developed by our team in order to fabricate tough gels with free form. We are aiming to create artificial blood vessel of the gel material by 3D gel printer. Artificial blood vessel is expected to be used for vascular surgery practice. The artificial blood vessel made by 3D gel printer can be create to free form on the basis of the biological data of the patient. Therefore, we believe it is possible to contribute to increasing the success rate and safety of vascular surgery by creating artificial blood vessel with 3D gel printer. The modeling method of SWIM-ER is as follow. Pregel solution is polymerized by one-point UV irradiation with optical fiber. The irradiation area is controlled by computer program, so that exact 3D free forming is realized. In this study, synthesis conditions are re-examined in order to improve the degree of freedom of fabrication. The dimensional accuracy in height direction is improved by increasing the cross linker concentration. We examined the relationship of resolution to the pitch and UV irradiation time in order to improve the modeling accuracy.

  3. Protein electrophoretic migration data from custom and commercial gradient gels.

    PubMed

    Miller, Andrew J; Roman, Brandon; Norstrom, Eric M

    2016-12-01

    This paper presents data related to the article "A method for easily customizable gradient gel electrophoresis" (A.J. Miller, B. Roman, E.M. Norstrom, 2016) [1]. Data is presented on the rate of electrophoretic migration of proteins in both hand-poured and commercially acquired acrylamide gradient gels. For each gel, migration of 9 polypeptides of various masses was measured upon completion of gel electrophoresis. Data are presented on the migration of proteins within separate lanes of the same gel as well as migration rates from multiple gels. PMID:27622203

  4. Jupiter in blue, ultraviolet and near infrared

    NASA Technical Reports Server (NTRS)

    2000-01-01

    These three images of Jupiter, taken through the narrow angle camera of NASA's Cassini spacecraft from a distance of 77.6 million kilometers (48.2 million miles) on October 8, reveal more than is apparent to the naked eye through a telescope.

    The image on the left was taken through the blue filter. The one in the middle was taken in the ultraviolet. The one on the right was taken in the near infrared.

    The blue-light filter is within the part of the electromagnetic spectrum detectable by the human eye. The appearance of Jupiter in this image is, consequently, very familiar. The Great Red Spot (below and to the right of center) and the planet's well-known banded cloud lanes are obvious. The brighter bands of clouds are called zones and are probably composed of ammonia ice particles. The darker bands are called belts and are made dark by particles of unknown composition intermixed with the ammonia ice.

    Jupiter's appearance changes dramatically in the ultraviolet and near infrared images. These images are near negatives of each other and illustrate the way in which observations in different wavelength regions can reveal different physical regimes on the planet.

    All gases scatter sunlight efficiently at short wavelengths; this is why the sky appears blue on Earth. The effect is even more pronounced in the ultraviolet. The gases in Jupiter's atmosphere, above the clouds, are no different. They scatter strongly in the ultraviolet, making the deep banded cloud layers invisible in the middle image. Only the very high altitude haze appears dark against the bright background. The contrast is reversed in the near infrared, where methane gas, abundant on Jupiter but not on Earth, is strongly absorbing and therefore appears dark. Again the deep clouds are invisible, but now the high altitude haze appears relatively bright against the dark background. High altitude haze is seen over the poles and the equator.

    The Great Red Spot, prominent in all images, is

  5. Mechanical properties and morphology of polymer gels

    NASA Astrophysics Data System (ADS)

    Sliozberg, Yelena; Sirk, Timothy; Brennan, John; Andzelm, Jan; Mrozek, Randy; Lenhart, Joseph

    2012-02-01

    Understanding morphology and mechanical response of polymeric gels is of particular importance to design materials with required energy dissipation characteristics. We will present our latest results for polymer gels based on 1) self-assembled block copolymers and 2) chemically cross-linked polymers. The dissipative particle dynamics (DPD) was used to predict morphology in good agreement with atomic force microscopy. We have performed DPD non-equilibrium oscillatory shear calculations predicting elastic modulus of unentangled gels that correlates well with experimental rheology data. However, this methodology fails to predict mechanics of entangled polymer networks due to unphysical chain crossing brought by the soft potentials used in DPD simulations. Recently, we have introduced an improved segmental repulsion potential that removes the bond crossing allowing for reptation dynamics. The improved DPD method was used in simulations for entangled gels to explore impact of branched architecture of solvent on the mechanical response to the tensile deformation. Novel architectures of solvent resulting in a dramatic increase of the elastic modulus were identified. The topological analysis was applied to understand contributions of chemical cross-links and entanglements to the stress.

  6. Ionic Conduction Mechanism of Polymer Gel Electrolytes

    NASA Astrophysics Data System (ADS)

    Saito, Yuria; Kataoka, Hiroshi

    2002-12-01

    Carrier migration mechanism of polymer gel electrolyte for lithium secondary batteries was investigated through the dynamic behavior of diffusion coefficient and conductivity. The gel prepared with PEO showed a homogeneous structure with any fraction of the electrolyte solution. The diffusion coefficient of the ionic species decreased with the increase in the polymer fraction in the gel. Cation migration is closely associated with the polymer, showing the reduced activation energy for diffusion with polymer in contrast to the increasing feature of the activation energy of the anion diffusion. The PVDF-gel electrolytes have a solid solubility limit due to the swelling saturation. The excess solution was then trapped in the cavities of the swollen polymer network. As a result, the diffusion showed two components. One is the fast migration of the carriers similar to that in the solution and the other is the relatively slow migration in the swollen region. The latter was influenced by the polymer due to the physical blocking and chemical interactive effects.

  7. Gel injection successfully shuts off excess water

    SciTech Connect

    1995-11-01

    Unocal applied a high-temperature organic polymer gel in Feather field Well H-43 in the UK North Sea to reduce water production in them more-permeable upper perforated section of the Brent Sand. The operation and technical details of the polymer system developed by Unocal, and how it was applied, are described in paper SPE 30426, ``Water shut off in the North Sea; Testing a new polymer system in the Heather field, UKCS Block 2/5.`` The authors concluded that the new gel system successfully isolated the Upper Brent water production, increasing oil production and decreasing water production. Lower perforations were successfully isolated using sized calcium carbonate suspended in an HEC polymer--a technique difficult to monitor in the deviated well. Batch mixing provided ``excellent`` quality gel, closely matching lab measured performance. And the gel required no pre-cooling in the near-wellbore area. Some 1,100 bbl were injected without excessive wellhead pressure, at 1 bpm. A summary of the paper`s highlights is presented here.

  8. Gel Permeation Chromatography of Fluoroether Polymers

    NASA Technical Reports Server (NTRS)

    Korus, Roger A.; Rosser, Robert W.

    1978-01-01

    A Method is described for determining the molecular weight distribution of fluorinated polymers by gel permeation chromatography. Porous silica-packed columns are used with Freon 113 as the chromatographic solvent. Fluoroether oligomers are used for column calibration in the molecular weight range of 1400 to 12000.

  9. Gel Filtration Chromatography: A Laboratory Experiment.

    ERIC Educational Resources Information Center

    Hurlbut, Jeffrey A.; Schonbeck, Niels D.

    1984-01-01

    Describes a rapid, visual demonstration of protein separation by gel filtration chromatography. The procedure separates two highly colored proteins of different molecular weights on a Sephadex G-75 in 45 minutes. This time includes packing the column as well. Background information, reagents needed, procedures used, and results obtained are…

  10. Aloe vera leaf gel: a review update.

    PubMed

    Reynolds, T; Dweck, A C

    1999-12-15

    Research since the 1986 review has largely upheld the therapeutic claims made in the earlier papers and indeed extended them into other areas. Treatment of inflammation is still the key effect for most types of healing but it is now realized that this is a complex process and that many of its constituent processes may be addressed in different ways by different gel components. A common theme running though much recent research is the immunomodulatory properties of the gel polysaccharides, especially the acetylated mannans from Aloe vera, which are now a proprietary substance covered by many patents. There have also been, however, persistent reports of active glycoprotein fractions from both Aloe vera and Aloe arborescens. There are also cautionary investigations warning of possible allergic effects on some patients. Reports also describe antidiabetic, anticancer and antibiotic activities, so we may expect to see a widening use of aloe gel. Several reputable suppliers produce a stabilized aloe gel for use as itself or in formulations and there may be moves towards isolating and eventually providing verified active ingredients in dosable quantities PMID:10624859

  11. Gel bead composition for metal adsorption

    SciTech Connect

    Scott, Charles D.; Woodward, Charlene A.; Byers, Charles H.

    1991-01-01

    The invention is a gel bead comprising propylene glycol alginate and bone gelatin and is capable of removing metals such as Sr and Cs from solution without adding other adsorbents. The invention could have application to the nuclear industry's waste removal activities.

  12. Gel bead composition for metal adsorption

    DOEpatents

    Scott, Charles D.; Woodward, Charlene A.; Byers, Charles H.

    1990-01-01

    The invention is a gel bead comprising propylene glycol alginate and bone gelatin and is capable of removing metals such as Sr and Cs from solution without adding other adsorbents. The invention could have application to the nuclear industry's waste removal activities.

  13. Simple Cloud Chambers Using Gel Ice Packs

    ERIC Educational Resources Information Center

    Kamata, Masahiro; Kubota, Miki

    2012-01-01

    Although cloud chambers are highly regarded as teaching aids for radiation education, school teachers have difficulty in using cloud chambers because they have to prepare dry ice or liquid nitrogen before the experiment. We developed a very simple and inexpensive cloud chamber that uses the contents of gel ice packs which can substitute for dry…

  14. Sol-Gel Derived Hafnia Coatings

    NASA Technical Reports Server (NTRS)

    Feldman, Jay D.; Stackpoole, Mairead; Blum, Yigal; Sacks, Michael; Ellerby, Don; Johnson, Sylvia M.; Venkatapathy, Ethiras (Technical Monitor)

    2002-01-01

    Sol-gel derived hafnia coatings are being developed to provide an oxidation protection layer on ultra-high temperature ceramics for potential use in turbine engines (ultra-efficient engine technology being developed by NASA). Coatings using hafnia sol hafnia filler particles will be discussed along with sol synthesis and characterization.

  15. Sol-Gel Synthesis Of Aluminoborosilicate Powders

    NASA Technical Reports Server (NTRS)

    Bull, Jeffrey; Leiser, Daniel; Selvaduray, Guna

    1992-01-01

    Application of sol-gel process to synthesis of aluminoborosilicate powders shows potential for control of microstructures of materials. Development of materials having enhanced processing characteristics prove advantageous in extending high-temperature endurance of fibrous refractory composite insulation made from ceramic fibers.

  16. Xanthan gel system effective for profile modification

    SciTech Connect

    Burkholder, L.

    1985-04-15

    To cope with the problem of optimizing reservoir sweep efficiency, many companies today are utilizing a technique known as profile modification. This technique is based on the premise that a gelled polymer formulation can be injected into the reservoir some distance beyond the well bore where it creates a flow diversion. The successful application of profile modification techniques has resulted in significant increases in incremental oil recovery. The injectant is a xanthan-gum solution precross-linked with a chromium complex to form a gel. The polymer/chromium combination reduces permeability in the thief zones and diverts a higher percentage of the displacing fluids into previously unswept, oil-saturated portions of the reservoir. Although reservoir characteristics and brine composition are key considerations, xanthan/chrome gels can be tailored to meet almost any conditions. Fractures will require strong gels while tight formations, or formations with low parting pressures, will require thinner gels. Slug volume is designed to treat the ''thief'' interval and must be carefully sized to improve sweep efficiency within economical limits.

  17. Growth of hydroxyapatite nanoparticles on silica gels.

    PubMed

    Rivera-Muñoz, E M; Huirache-Acuña, R; Velázquez, R; Alonso-Núñez, G; Eguía-Eguía, S

    2011-06-01

    Synthetic, hydroxyapatite nanoparticles were grown on the surface of silica gels. The synthesis of those nanoparticles was obtained by immersing silica gels in a simulated body fluid (SBF) at 37 degrees C. The SBF was replaced every week to keep constant the Ca and P ion concentration and subsequent growth of hydroxyapatite was evaluated after 1-6 weeks of total soaking time in SBF. Hydroxyapatite nanoparticles were observed by scanning electron microscopy (SEM) on the surface of silica gel samples and confirmed by energy dispersive X-ray spectroscopy (EDS), Fourier Transform Infra Red Spectroscopy (FTIR) and powder X-ray Diffractometry (XRD) analysis. These particles show a regular shape and uniform size every week, keeping within the nanoscale always. Both the size and morphology of hydroxyapatite nanoparticles obtained are the result of the use of different chemical additives in the synthesis of silica gels, since they affect the liquid-to-solid interface, and the growth could correspond to a diffusion limited aggregation (DLA) process. A more detailed analysis, with higher magnifications, showed that hydroxyapatite nanoparticles are not solid spheres, showing a branched texture and their size depends on the scale and resolution of the measure instrument. PMID:21770224

  18. Electrophoretic Porosimetry of Sol-Gels

    NASA Technical Reports Server (NTRS)

    Snow, L. A.; Smith, D. D.; Sibille, L.; Hunt, A. J.; Ng, J.; Rose, M. Franklin (Technical Monitor)

    2000-01-01

    It has been hypothesized that gravity has an effect on the formation and resulting microstructure of sol-gels. In order to more clearly resolve the effect of gravity, pores may be non-destructively analyzed in the wet gel, circumventing the shrinkage and coarsening associated with the drying procedure. We discuss the development of an electrophoretic technique, analogous to affinity chromatography, for the determination of pore size distribution and its application to silica gels. Specifically a monodisperse charged dye is monitored by an optical densitometer as it moves through the wet gel under the influence of an electric field. The transmittance data (output) represents the convolution of the dye concentration profile at the beginning of the run (input) with the pore size distribution (transfer function), i.e. linear systems theory applies. Because of the practical difficulty in producing a delta function input dye profile we prefer instead to use a step function. Average pore size is then related to the velocity of this dye front, while the pore size distribution is related to the spreading of the front. Preliminary results of this electrophoretic porosimetry and its application to ground and space-grown samples will be discussed.

  19. Driven Polymer Translocation into a Crosslinked Gel

    NASA Astrophysics Data System (ADS)

    Sean, David; Slater, Gary

    2015-03-01

    In a typical polymer translocation setup, a thin membrane is used to separate two chambers and a polyelectrolyte is driven by an electric field to translocate from one side of the membrane to the other via a small nanopore. However, the high translocation rate that results from the forces required to drive this process makes optical and/or electrical analysis of the translocating polymer challenging. Using coarse-grained Langevin Dynamics simulations we investigate how the translocation process can be slowed down by placing a crosslinked gel on the trans-side of the membrane. Since the driving electric field is localized in the neighborhood of the nanopore, electrophoretic migration is only achieved by a ``pushing'' action from the polymer segment residing in the nanopore. For the case of a flexible polymer we find that the polymer fills the gel pores via multiple ``herniation'' processes, whereas for a semi-flexible chain in a tight gel there are no hernias and the polymer follows a smooth curvilinear path. Moreover, for the case of a semi-flexible polymer the gel makes the translocation process more uniform by reducing the acceleration at the end of the process.

  20. 3D gel printing for soft-matter systems innovation

    NASA Astrophysics Data System (ADS)

    Furukawa, Hidemitsu; Kawakami, Masaru; Gong, Jin; Makino, Masato; Kabir, M. Hasnat; Saito, Azusa

    2015-04-01

    In the past decade, several high-strength gels have been developed, especially from Japan. These gels are expected to use as a kind of new engineering materials in the fields of industry and medical as substitutes to polyester fibers, which are materials of artificial blood vessels. We consider if various gel materials including such high-strength gels are 3D-printable, many new soft and wet systems will be developed since the most intricate shape gels can be printed regardless of the quite softness and brittleness of gels. Recently we have tried to develop an optical 3D gel printer to realize the free-form formation of gel materials. We named this apparatus Easy Realizer of Soft and Wet Industrial Materials (SWIM-ER). The SWIM-ER will be applied to print bespoke artificial organs, including artificial blood vessels, which will be possibly used for both surgery trainings and actual surgery. The SWIM-ER can print one of the world strongest gels, called Double-Network (DN) gels, by using UV irradiation through an optical fiber. Now we also are developing another type of 3D gel printer for foods, named E-Chef. We believe these new 3D gel printers will broaden the applications of soft-matter gels.