Science.gov

Sample records for agt power-train system

  1. Advanced Gas Turbine (AGT) power-train system development

    NASA Technical Reports Server (NTRS)

    Helms, H. E.; Johnson, R. A.; Gibson, R. K.

    1982-01-01

    Technical work on the design and component testing of a 74.5 kW (100 hp) advanced automotive gas turbine is described. Selected component ceramic component design, and procurement were tested. Compressor tests of a modified rotor showed high speed performance improvement over previous rotor designs; efficiency improved by 2.5%, corrected flow by 4.6%, and pressure ratio by 11.6% at 100% speed. The aerodynamic design is completed for both the gasifier and power turbines. Ceramic (silicon carbide) gasifier rotors were spin tested to failure. Improving strengths is indicated by burst speeds and the group of five rotors failed at speeds between 104% and 116% of engine rated speed. The emission results from combustor testing showed NOx levels to be nearly one order of magnitude lower than with previous designs. A one piece ceramic exhaust duct/regenerator seal platform is designed with acceptable low stress levels.

  2. Advanced Gas Turbine (AGT): Power-train system development

    NASA Technical Reports Server (NTRS)

    Helms, H. E.; Johnson, R. A.; Gibson, R. K.; Smith, L. B.

    1983-01-01

    Technical work on the design and effort leading to the testing of a 74.5 kW (100 hp) automotive gas turbine is described. The general effort was concentrated on building an engine for test starting in July. The buildup progressed with only routine problems and the engine was delivered to the test stand 9 July. In addition to the engine build effort, work continued in selected component areas. Ceramic turbine parts were built and tested. Burst tests of ceramic rotors show strengths are approaching that achieved in test bars; proof testing is required for acceptable strength ceramic vanes. Over 25 hours was accumulated on the combustor rig in three test modes: pilot nozzle only, start nozzle, and main nozzle operation. Satisfactory ignition was achieved for a wide range of starting speeds and the lean blowout limit was as low as 0.06 kg/b (0.14 lb/hr). Lean blowout was more a function of nozzle atomization than fuel/air ratio. A variety of cycle points were tested. Transition from start nozzle flow to main nozzle flow was done manually without difficulty. Regenerator parts were qualification tested without incident and the parts were assembled on schedule. Rig based performance matched first build requirements. Repeated failures in the harmonic drive gearbox during rig testing resulted in that concept being abandoned for an alternate scheme.

  3. Advanced Gas Turbine (AGT) powertrain system development for automotive applications

    NASA Technical Reports Server (NTRS)

    1982-01-01

    A gas turbine powertrain for automobiles with reduced fuel consumption and reduced environmental impact is investigated. The automotive gas turbine, when installed in an automobile (3000 pounds inertia weight), provides a CFDC fuel economy of 42.8 miles per gallon based on EPA test procedures and diesel No. 2 fuel. The AGT powered vehicle substantially gives the same overall vehicle driveability and performance as a comparable production vehicle powered by a conventional spark ignition powertrain system. The emissions are less than federal standards, and a variety of fuels can be used.

  4. Advanced Gas Turbine (AGT) powertrain system development for automotive applications

    NASA Technical Reports Server (NTRS)

    1982-01-01

    Topics covered include the AGT 101 engine test; compressor design modification; cold air turbine testing; Mod 1 alloy turbine rotor fabrication; combustion aspects; regenerator development; and thermal screening tests for ceramic materials. The foil gas bearings, rotor dynamics, and AGT controls and accessories are also considered.

  5. Advanced Gas Turbine (AGT) powertrain system development for automotive applications

    NASA Technical Reports Server (NTRS)

    1981-01-01

    An automotive gas turbine powertrain system which, when installed in a 1985 production vehicle (3000 pounds inertia weight), is being developed with a CFDC fuel economy of 42.8 miles per gallon based on Environmental Protection Agency (EPA) test procedures and diesel No. 2 fuel. The AGT-powered vehicle shall give substantially the same overall vehicle driveability and performance as a comparable 1985 production vehicle powered by a conventional spark ignition powertrain system (baseline system). Gaseous emissions and particulate levels less than: NOx = 0.4 gm/mile, HC = 0.41 gm/mile, and CO = 3.4 gm/mile, and a total particulate of 0.2 gm/mile, using the same fuel as used for fuel economy measurements is expected, along with the ability to use a variety of alternate fuels.

  6. Advanced Gas Turbine (AGT) powertrain system development for automotive applications

    NASA Technical Reports Server (NTRS)

    1980-01-01

    Progress in the development of a gas turbine engine to improve fuel economy, reduce gaseous emissions and particulate levels, and compatible with a variety of alternate fuels is reported. The powertrain is designated AGT101 and consists of a regenerated single shaft gas turbine engine, a split differential gearbox and a Ford Automatic Overdrive production transmission. The powertrain is controlled by an electronic digital microprocessor and associated actuators, instrumentation, and sensors. Standard automotive accessories are driven by engine power provided by an accessory pad on the gearbox. Component/subsystem development progress is reported in the following areas: compressor, turbine, combustion system, regenerator, gearbox/transmission, structures, ceramic components, foil gas bearing, bearings and seals, rotor dynamics, and controls and accessories.

  7. Advanced Gas Turbine (AGT) powertrain system development for automotive applications

    NASA Technical Reports Server (NTRS)

    1981-01-01

    Preliminary layouts were made for the exhaust system, air induction system, and battery installation. Points of interference were identified and resolved by altering either the vehicle or engine designs. An engine general arrangement evolved to meet the vehicle engine compartment constraints while minimizing the duct pressure losses and the heat rejection. A power transfer system (between gasifier and power turbines) was developed to maintain nearly constant temperatures throughout the entire range of engine operation. An advanced four speed automatic transmission was selected to be used with the engine. Performance calculations show improvements in component efficiencies and an increase in fuel economy. A single stage centrifugal compressor design was completed and released for procurement. Gasifier turbine, power turbine, combustor, generator, secondary systems, materials, controls, and transmission development are reported.

  8. Advanced Gas Turbine (AGT) powertrain system development for automotive applications

    NASA Technical Reports Server (NTRS)

    1981-01-01

    Compressor development, turbine, combustion, regenerator system, gearbox/transmission, ceramic material and component development, foil gas bearings, bearings and seals, rotor dynamics development, and controls and accessories are discussed.

  9. Advanced Gas Turbine (AGT) powertrain system development for automotive applications report

    NASA Technical Reports Server (NTRS)

    1984-01-01

    This report describes progress and work performed during January through June 1984 to develop technology for an Advanced Gas Turbine (AGT) engine for automotive applications. Work performed during the first eight periods initiated design and analysis, ceramic development, component testing, and test bed evaluation. Project effort conducted under this contract is part of the DOE Gas Turbine Highway Vehicle System Program. This program is oriented at providing the United States automotive industry the high-risk long-range techology necessary to produce gas turbine engines for automobiles with reduced fuel consumption and reduced environmental impact. Technology resulting from this program is intended to reach the marketplace by the early 1990s.

  10. Spectral duality in integrable systems from AGT conjecture

    NASA Astrophysics Data System (ADS)

    Mironov, A.; Morozov, A.; Zenkevich, Y.; Zotov, A.

    2013-03-01

    We describe relationships between integrable systems with N degrees of freedom arising from the Alday-Gaiotto-Tachikawa conjecture. Namely, we prove the equivalence (spectral duality) between the N-cite Heisenberg spin chain and a reduced gl N Gaudin model both at classical and quantum level. The former one appears on the gauge theory side of the Alday-Gaiotto-Tachikawa relation in the Nekrasov-Shatashvili (and further the Seiberg-Witten) limit while the latter one is natural on the CFT side. At the classical level, the duality transformation relates the Seiberg-Witten differentials and spectral curves via a bispectral involution. The quantum duality extends this to the equivalence of the corresponding Baxter-Schrödinger equations (quantum spectral curves). This equivalence generalizes both the spectral self-duality between the 2 × 2 and N × N representations of the Toda chain and the famous Adams-Harnad-Hurtubise duality.

  11. Advanced Gas Turbine (AGT) powertrain system initial development report

    NASA Technical Reports Server (NTRS)

    1980-01-01

    The powertrain consists of a single shaft regenerated gas turbine engine utilizing ceramic hot section components, coupled to a slit differential gearbox with an available variable stator torque converter and an available Ford intergral overdrive four-speed automatic transmission. Predicted fuel economy using gasoline fuel over the combined federal driving cycle (CFDC) is 15.3 km/1, which represents a 59% improvement over the spark-ignition-powered baseline vehicle. Using DF2 fuel, CFDC mileage estimates are 17.43 km/1. Zero to 96.6 km/hr acceleration time is 11.9 seconds with a four-second accleration distance of 21.0 m. The ceramic radial turbine rotor is discussed along with the control system for the powertrain.

  12. Critical assessment of power trains with fuel-cell systems and different fuels

    NASA Astrophysics Data System (ADS)

    Höhlein, B.; von Andrian, S.; Grube, Th; Menzer, R.

    Legal regulations (USA, EU) are a major driving force for intensifying technological developments with respect to the global automobile market. In the future, highly efficient vehicles with very low emission levels will include low-temperature fuel-cell systems (PEFC) as units of electric power trains. With alcohols, ether or hydrocarbons used as fuels for these new electric power trains, hydrogen as PEFC fuel has to be produced on board. These concepts including the direct use of methanol in fuel-cell systems, differ considerably in terms of both their development prospects and the results achieved so far. Based on process engineering analyses for net electricity generation in PEFC-powered power trains, as well as on assumptions for electric power trains and vehicle configurations, different fuel-cell performances and fuel processing units for octane, diesel, methanol, ethanol, propane and dimethylether have been evaluated as fuels. The possible benefits and key challenges for different solutions of power trains with fuel-cell systems/on-board hydrogen production and with direct methanol fuel-cell (DMFC) systems have been assessed. Locally, fuel-cell power trains are almost emission-free and, unlike battery-powered vehicles, their range is comparable to conventional vehicles. Therefore, they have application advantages cases of particularly stringent emission standards requiring zero emission. In comparison to internal combustion engines, using fuel-cell power trains can lead to clear reductions in primary energy demand and global, climate-relevant emissions providing the advantage of the efficiency of the hydrogen/air reaction in the fuel cell is not too drastically reduced by additional conversion steps of on-board hydrogen production, or by losses due to fuel supply provision.

  13. Development of Analytical Algorithm for the Performance Analysis of Power Train System of an Electric Vehicle

    NASA Astrophysics Data System (ADS)

    Kim, Chul-Ho; Lee, Kee-Man; Lee, Sang-Heon

    Power train system design is one of the key R&D areas on the development process of new automobile because an optimum size of engine with adaptable power transmission which can accomplish the design requirement of new vehicle can be obtained through the system design. Especially, for the electric vehicle design, very reliable design algorithm of a power train system is required for the energy efficiency. In this study, an analytical simulation algorithm is developed to estimate driving performance of a designed power train system of an electric. The principal theory of the simulation algorithm is conservation of energy with several analytical and experimental data such as rolling resistance, aerodynamic drag, mechanical efficiency of power transmission etc. From the analytical calculation results, running resistance of a designed vehicle is obtained with the change of operating condition of the vehicle such as inclined angle of road and vehicle speed. Tractive performance of the model vehicle with a given power train system is also calculated at each gear ratio of transmission. Through analysis of these two calculation results: running resistance and tractive performance, the driving performance of a designed electric vehicle is estimated and it will be used to evaluate the adaptability of the designed power train system on the vehicle.

  14. Power Trains.

    ERIC Educational Resources Information Center

    Kukuk, Marvin; Mathis, Joe

    This curriculum guide is part of a series designed to teach students about diesel engines. The materials in this power trains guide apply to both on-road and off-road vehicles and include information about chain and belt drives used in tractors and combines. These instructional materials, containing nine units, are written in terms of student…

  15. Flow simulation of the Component Development Integration Facility magnetohydrodynamic power train system

    SciTech Connect

    Chang, S.L.; Lottes, S.A.; Bouillard, J.X.; Petrick, M.

    1997-11-01

    This report covers application of Argonne National Laboratory`s (ANL`s) computer codes to simulation and analysis of components of the magnetohydrodynamic (MHD) power train system at the Component Development and Integration Facility (CDIF). Major components of the system include a 50-MWt coal-fired, two-stage combustor and an MHD channel. The combustor, designed and built by TRW, includes a deswirl section between the first and the second-stage combustor and a converging nozzle following the second-stage combustor, which connects to the MHD channel. ANL used computer codes to simulate and analyze flow characteristics in various components of the MHD system. The first-stage swirl combustor was deemed a mature technology and, therefore, was not included in the computer simulation. Several versions of the ICOMFLO computer code were used for the deswirl section and second-stage combustor. The MGMHD code, upgraded with a slag current leakage submodel, was used for the MHD channel. Whenever possible data from the test facilities were used to aid in calibrating parameters in the computer code, to validate the computer code, or to set base-case operating conditions for computations with the computer code. Extensive sensitivity and parametric studies were done on cold-flow mixing in the second-stage combustor, reacting flow in the second-stage combustor and converging nozzle, and particle-laden flow in the deswirl zone of the first-stage combustor, the second-stage combustor, and the converging nozzle. These simulations with subsequent analysis were able to show clearly in flow patterns and various computable measures of performance a number of sensitive and problematical areas in the design of the power train. The simulations of upstream components also provided inlet parameter profiles for simulation of the MHD power generating channel. 86 figs., 18 tabs.

  16. The AGT101 technology - An automotive alternative

    NASA Technical Reports Server (NTRS)

    Rackley, R. A.; Davis, K. A.

    1981-01-01

    The Advanced Gas Turbine Powertrain System Development Project is oriented at providing the United States automotive industry the technology base necessary to produce gas turbine powertrains for automotive applications that will have: (1) reduced fuel consumption, (2) the ability to use a variety of fuels, (3) low emissions, and (4) competitive cost/performance. The AGT101 powertrain being developed consists of a regenerated single-shaft gas turbine engine flat rated at 74.6 kW (100 hp) coupled to a split-differential gearbox and a Ford automatic overdrive production transmission. Performance predictions for the AGT101 powertrain represent a 59-percent improvement in mileage estimates over a 1985 conventionally-powered automobile for the combined federal driving cycle.

  17. Automotive Power Trains.

    ERIC Educational Resources Information Center

    Marine Corps Inst., Washington, DC.

    This correspondence course, originally developed for the Marine Corps, is designed to provide mechanics with an understanding of the operation, maintenance, and troubleshooting of automotive power trains and certain auxiliary equipment. The course contains six study units covering basic power trains; clutch principles and operations; conventional…

  18. A system-level mathematical model for evaluation of power train performance of load-leveled electric-vehicles

    NASA Technical Reports Server (NTRS)

    Purohit, G. P.; Leising, C. J.

    1984-01-01

    The power train performance of load leveled electric vehicles can be compared with that of nonload leveled systems by use of a simple mathematical model. This method of measurement involves a number of parameters including the degree of load leveling and regeneration, the flywheel mechanical to electrical energy fraction, and efficiencies of the motor, generator, flywheel, and transmission. Basic efficiency terms are defined and representative comparisons of a variety of systems are presented. Results of the study indicate that mechanical transfer of energy into and out of the flywheel is more advantageous than electrical transfer. An optimum degree of load leveling may be achieved in terms of the driving cycle, battery characteristics, mode of mechanization, and the efficiency of the components. For state of the art mechanically coupled flyheel systems, load leveling losses can be held to a reasonable 10%; electrically coupled systems can have losses that are up to six times larger. Propulsion system efficiencies for mechanically coupled flywheel systems are predicted to be approximately the 60% achieved on conventional nonload leveled systems.

  19. M-theoretic derivations of 4d-2d dualities: from a geometric Langlands duality for surfaces, to the AGT correspondence, to integrable systems

    NASA Astrophysics Data System (ADS)

    Tan, Meng-Chwan

    2013-07-01

    In part I, we extend our analysis in [arXiv:0807.1107], and show that a mathematically conjectured geometric Langlands duality for complex surfaces in [1], and its generalizations — which relate some cohomology of the moduli space of certain ("ramified") G-instantons to the integrable representations of the Langlands dual of certain affine (sub) G-algebras, where G is any compact Lie group — can be derived, purely physically, from the principle that the spacetime BPS spectra of string-dual M-theory compactifications ought to be equivalent. In part II, to the setup in part I, we introduce Omega-deformation via fluxbranes and add half-BPS boundary defects via M9-branes, and show that the celebrated AGT correspondence in [2, 3], and its generalizations — which essentially relate, among other things, some equivariant cohomology of the moduli space of certain ("ramified") G-instantons to the integrable representations of the Langlands dual of certain affine -algebras — can likewise be derived from the principle that the spacetime BPS spectra of string-dual M-theory compactifications ought to be equivalent. In part III, we consider various limits of our setup in part II, and connect our story to chiral fermions and integrable systems. Among other things, we derive the NekrasovOkounkov conjecture in [4] — which relates the topological string limit of the dual Nekrasov partition function for pure G to the integrable representations of the Langlands dual of an affine G-algebra — and also demonstrate that the Nekrasov-Shatashvili limit of the "fullyramified" Nekrasov instanton partition function for pure G is a simultaneous eigenfunction of the quantum Toda Hamiltonians associated with the Langlands dual of an affine G-algebra. Via the case with matter, we also make contact with Hitchin systems and the "ramified" geometric Langlands correspondence for curves.

  20. AGT100 turbomachinery. [for automobiles

    NASA Technical Reports Server (NTRS)

    Tipton, D. L.; Mckain, T. F.

    1982-01-01

    High-performance turbomachinery components have been designed and tested for the AGT100 automotive engine. The required wide range of operation coupled with the small component size, compact packaging, and low cost of production provide significant aerodynamic challenges. Aerodynamic design and development testing of the centrifugal compressor and two radial turbines are described. The compressor achieved design flow, pressure ratio, and surge margin on the initial build. Variable inlet guide vanes have proven effective in modulating flow capacity and in improving part-speed efficiency. With optimum use of the variable inlet guide vanes, the initial efficiency goals have been demonstrated in the critical idle-to-70% gasifier speed range. The gasifier turbine exceeded initial performance goals and demonstrated good performance over a wide range. The radial power turbine achieved 'developed' efficiency goals on the first build.

  1. Advanced Gas Turbine (AGT) Technology Development Project

    NASA Technical Reports Server (NTRS)

    1987-01-01

    This report is the eleventh in the series of Technical Summary reports for the Advanced Gas Turbine (AGT) Technology Development Project, authorized under NASA Contract DEN3-167, and sponsored by the Department of Energy (DOE). This report was prepared by Garrett Turbine Engine Company, A Division of the Garrett Corporation, and includes information provided by Ford Motor Company, the Standard Oil Company, and AiResearch Casting Company. This report covers plans and progress for the period July 1, 1985 through June 30, 1986. Technical progress during the reported period was highlighted by the 85-hour endurance run of an all-ceramic engine operating in the 2000 to 2250 F temperature regime. Component development continued in the areas of the combustion/fuel injection system, regenerator and seals system, and ceramic turbine rotor attachment design. Component rig testing saw further refinements. Ceramic materials showed continued improvements in required properties for gas turbine applications; however, continued development is needed before performance and reliability goals can be set.

  2. Advanced Gas Turbine (AGT) technology development project

    NASA Technical Reports Server (NTRS)

    1987-01-01

    This report is the final in a series of Technical Summary Reports for the Advanced Gas Turbine (AGT) Technology Development Project, authorizrd under NASA Contract DEN3-167 and sponsored by the DOE. The project was administered by NASA-Lewis Research Center of Cleveland, Ohio. Plans and progress are summarized for the period October 1979 through June 1987. This program aims to provide the US automotive industry the high risk, long range technology necessary to produce gas turbine engines for automobiles that will reduce fuel consumption and reduce environmental impact. The intent is that this technology will reach the marketplace by the 1990s. The Garrett/Ford automotive AGT was designated AGT101. The AGT101 is a 74.5 kW (100 shp) engine, capable of speeds to 100,000 rpm, and operates at turbine inlet temperatures to 1370 C (2500 F) with a specific fuel consumption level of 0.18 kg/kW-hr (0.3 lbs/hp-hr) over most of the operating range. This final report summarizes the powertrain design, power section development and component/ceramic technology development.

  3. Comparison of different vehicle power trains

    NASA Astrophysics Data System (ADS)

    Mizsey, Peter; Newson, Esmond

    Four different alternatives of mobile power train developments (hybrid diesel, fuel cell operating with hydrogen produced on a petrochemical basis, methanol reformer-fuel cell system, gasoline reformer-fuel cell system), are compared with the gasoline internal combustion engine (ICE), for well-to-wheel efficiencies, CO 2 emissions, and investment costs. Although the ICE requires the lowest investment cost, it is not competitive in well-to-wheel efficiencies and less favourable than the above alternatives for CO 2 emissions. The hybrid diesel power train has the highest well-to-wheel efficiency (30%), but its well-to-wheel carbon dioxide emission is similar to that of the fuel cell power train operated with compressed hydrogen produced on a centralised petrochemical basis. This latter case, however, has the advantage over the hybrid diesel power train that the carbon dioxide emission is concentrated and easier to control than the several point-like sources of emissions. Among the five cases studied only the on-board reforming of methanol offers the possibility of using a renewable energy source (biomass).

  4. Fuel cell power trains for road traffic

    NASA Astrophysics Data System (ADS)

    Höhlein, Bernd; Biedermann, Peter; Grube, Thomas; Menzer, Reinhard

    Legal regulations, especially the low emission vehicle (LEV) laws in California, are the driving forces for more intensive technological developments with respect to a global automobile market. In the future, high efficient vehicles at very low emission levels will include low temperature fuel cell systems (e.g., polymer electrolyte fuel cell (PEFC)) as units of hydrogen-, methanol- or gasoline-based electric power trains. In the case of methanol or gasoline/diesel, hydrogen has to be produced on-board using heated steam or partial oxidation reformers as well as catalytic burners and gas cleaning units. Methanol could also be used for direct electricity generation inside the fuel cell (direct methanol fuel cell (DMFC)). The development potentials and the results achieved so far for these concepts differ extremely. Based on the experience gained so far, the goals for the next few years include cost and weight reductions as well as optimizations in terms of the energy management of power trains with PEFC systems. At the same time, questions of fuel specification, fuel cycle management, materials balances and environmental assessment will have to be discussed more intensively. On the basis of process engineering analyses for net electricity generation in PEFC-powered power trains as well as on assumptions for both electric power trains and vehicle configurations, overall balances have been carried out. They will lead not only to specific energy demand data and specific emission levels (CO 2, CO, VOC, NO x) for the vehicle but will also present data of its full fuel cycle (FFC) in comparison to those of FFCs including internal combustion engines (ICE) after the year 2005. Depending on the development status (today or in 2010) and the FFC benchmark results, the advantages of balances results of FFC with PEFC vehicles are small in terms of specific energy demand and CO 2 emissions, but very high with respect to local emission levels.

  5. The AGT 101 advanced automotive gas turbine

    NASA Technical Reports Server (NTRS)

    Rackley, R. A.; Kidwell, J. R.

    1982-01-01

    A development program is described whose goal is the accumulation of the technology base needed by the U.S. automotive industry for the production of automotive gas turbine powertrains. Such gas turbine designs must exhibit reduced fuel consumption, a multi-fuel capability, and low exhaust emissions. The AGT101 powertrain described is a 74.6 kW, regenerated single-shaft gas turbine, operating at a maximum inlet temperature of 1644 K and coupled to a split differential gearbox and automatic overdrive transmission. The engine's single stage centrifugal compressor and single stage radial inflow turbine are mounted on a common shaft, and will operate at a maximum rotor speed of 100,000 rpm. All high temperature components, including the turbine rotor, are ceramic.

  6. Advanced Gas Turbine (AGT) technology report

    NASA Technical Reports Server (NTRS)

    1985-01-01

    Engine testing, ceramic component fabrication and evaluation, component performance rig testing, and producibility experiments at Pontiac comprised AGT 100 activities of this period, January to December 1984. Two experimental engines were available and allowed the evaluation of eight experimental assemblies. Operating time accumulated was 115 hr of burning and 156 hr total. Total cumulative engine operating time is now 225 hr. Build number 11 and 12 of engine S/N 1 totaled 28 burning hours and constituted a single assembly of the engine core--the compressor, both turbines, and the gearbox. Build number 11 of engine S/N 1 included a 1:07 hr continuous test at 100% gasifier speed (86,000 rpm). Build number 8 of engine S/N 2 was the first engine test with a ceramic turbine rotor. A mechanical loss test of an engine assembly revealed the actual losses to be near the original design allowance. Component development activity included rig testing of the compressor, combustor, and regenerator. Compressor testing was initiated on a rig modified to control the transfer of heat between flow path, lubricating oil, and structure. Results show successful thermal decoupling of the rig and lubricating/cooling oil. Rig evaluation of a reduced-friction compressor was initiated. Combustor testing covered qualification of ceramic parts for engine use, mapping of operating range limits, and evaluation of a relocated igniter plug. Several seal refinements were tested on the hot regenerator rig. An alternate regenerator disk, extruded MAS, was examined and found to be currently inadequate for the AGT 100 application. Also, a new technique for measuring leakage was explored on the regenerator rig. Ceramic component activity has focused on the development of state-of-the-art material strength characteristics in full-scale hardware. Injection-molded sintered alpha-SiC rotors were produced at Carborundum in an extensive process and tool optimization study.

  7. AGT (Advanced Gas Turbine) technology project

    NASA Technical Reports Server (NTRS)

    1988-01-01

    An overall summary documentation is provided for the Advanced Gas Turbine Technology Project conducted by the Allison Gas Turbine Division of General Motors. This advanced, high risk work was initiated in October 1979 under charter from the U.S. Congress to promote an engine for transportation that would provide an alternate to reciprocating spark ignition (SI) engines for the U.S. automotive industry and simultaneously establish the feasibility of advanced ceramic materials for hot section components to be used in an automotive gas turbine. As this program evolved, dictates of available funding, Government charter, and technical developments caused program emphases to focus on the development and demonstration of the ceramic turbine hot section and away from the development of engine and powertrain technologies and subsequent vehicular demonstrations. Program technical performance concluded in June 1987. The AGT 100 program successfully achieved project objectives with significant technology advances. Specific AGT 100 program achievements are: (1) Ceramic component feasibility for use in gas turbine engines has been demonstrated; (2) A new, 100 hp engine was designed, fabricated, and tested for 572 hour at operating temperatures to 2200 F, uncooled; (3) Statistical design methodology has been applied and correlated to experimental data acquired from over 5500 hour of rig and engine testing; (4) Ceramic component processing capability has progressed from a rudimentary level able to fabricate simple parts to a sophisticated level able to provide complex geometries such as rotors and scrolls; (5) Required improvements for monolithic and composite ceramic gas turbine components to meet automotive reliability, performance, and cost goals have been identified; (6) The combustor design demonstrated lower emissions than 1986 Federal Standards on methanol, JP-5, and diesel fuel. Thus, the potential for meeting emission standards and multifuel capability has been initiated

  8. Advanced Gas Turbine (AGT) Technology Project

    NASA Technical Reports Server (NTRS)

    1986-01-01

    Engine testing, ceramic component fabrication and evaluation, component performance rig testing, and analytical studies comprised AGT 100 activities during the 1985 year. Ten experimental assemblies (builds) were evaluated using two engines. Accrued operating time was 120 hr of burning and 170 hr total, bringing cumulative total operating time to 395 hr, all devoid of major failures. Tests identified the generator seals as the primary working fluid leakage sources. Power transfer clutch operation was demonstrated. An alpha SiC gasifier rotor engine test resulted in blade tip failures. Recurring case vibration and shaft whip have limited gasifier shaft speeds to 84%. Ceramic components successfully engine tested now include the SiC scroll assembly, Si3N3 turbine rotor, combustor assembly, regenerator disk bulkhead, turbine vanes, piston rings, and couplings. A compressor shroud design change to reduce heat recirculation back to the inlet was executed. Ceramic components activity continues to focus on the development of state-of-the-art material strength characteristics in full-scale engine hardware. Fiber reinforced glass-ceramic composite turbine (inner) backplates were fabricated by Corning Glass Works. The BMAS/III material performed well in engine testing. Backplates of MAS material have not been engine tested.

  9. Advanced Gas Turbine (AGT) powertrain system

    NASA Technical Reports Server (NTRS)

    Helms, H. E.; Kaufeld, J.; Kordes, R.

    1981-01-01

    A 74.5 kW(100 hp) advanced automotive gas turbine engine is described. A design iteration to improve the weight and production cost associated with the original concept is discussed. Major rig tests included 15 hours of compressor testing to 80% design speed and the results are presented. Approximately 150 hours of cold flow testing showed duct loss to be less than the design goal. Combustor test results are presented for initial checkout tests. Turbine design and rig fabrication is discussed. From a materials study of six methods to fabricate rotors, two have been selected for further effort. A discussion of all six methods is given.

  10. Power Trains. FOS: Fundamentals of Service.

    ERIC Educational Resources Information Center

    John Deere Co., Moline, IL.

    This power trains manual is one of a series of power mechanics for training in the servicing of transmissions, etc., on farm and industrial machines. Materials provide basic information and illustrations for use by vocational students and teachers as well as shop servicemen and laymen. The ten chapters focus on (1) Power Trains: How They Work; (2)…

  11. Advanced Gas Turbine (AGT) Technology Development Project, ceramic component developments

    NASA Technical Reports Server (NTRS)

    Teneyck, M. O.; Macbeth, J. W.; Sweeting, T. B.

    1987-01-01

    The ceramic component technology development activity conducted by Standard Oil Engineered Materials Company while performing as a principal subcontractor to the Garrett Auxiliary Power Division for the Advanced Gas Turbine (AGT) Technology Development Project (NASA Contract DEN3-167) is summarized. The report covers the period October 1979 through July 1987, and includes information concerning ceramic technology work categorized as common and unique. The former pertains to ceramic development applicable to two parallel AGT projects established by NASA contracts DEN3-168 (AGT100) and DEN3-167 (AGT101), whereas the unique work solely pertains to Garrett directed activity under the latter contract. The AGT101 Technology Development Project is sponsored by DOE and administered by NASA-Lewis. Standard Oil directed its efforts toward the development of ceramic materials in the silicon-carbide family. Various shape forming and fabrication methods, and nondestructive evaluation techniques were explored to produce the static structural components for the ceramic engine. This permitted engine testing to proceed without program slippage.

  12. On elementary proof of AGT relations from six dimensions

    NASA Astrophysics Data System (ADS)

    Mironov, A.; Morozov, A.; Zenkevich, Y.

    2016-05-01

    The actual definition of the Nekrasov functions participating in the AGT relations implies a peculiar choice of contours in the LMNS and Dotsenko-Fateev integrals. Once made explicit and applied to the original triply-deformed (6-dimensional) version of these integrals, this approach reduces the AGT relations to symmetry in q 1 , 2 , 3, which is just an elementary identity for an appropriate choice of the integration contour (which is, however, a little non-traditional). We illustrate this idea with the simplest example of N = (1 , 1) U (1) SYM in six dimensions, however all other cases can be evidently considered in a completely similar way.

  13. Ceramics for the AGT101 automotive gas turbine

    NASA Technical Reports Server (NTRS)

    Kreiner, D. M.; Wimmer, J. M.

    1981-01-01

    An advanced gas turbine powertrain for automotive application is being developed. Objectives of the program include a fuel consumption of 42.8 mpg on No. 2 diesel fuel in a 3000 pound car, same overall vehicle performance as obtained with a conventional spark ignition internal combustion engine, low emission, multiple fuel capacity, reliability, and competitive cost. The AGT101 powertrain consists of a power section, gearbox and transmission, and the design and analysis conducted thus far support the initial engine concept, as no significant design changes have been required. The ceramic rotor design approach and component materials are discussed, and it is projected that the AGT powertrain will be competitive with any other alternative powertrain in meeting the design objectives.

  14. Field testing advanced geothermal turbodrill (AGT). Phase 1 final report

    SciTech Connect

    Maurer, W.C.; Cohen, J.H.

    1999-06-01

    Maurer Engineering developed special high-temperature geothermal turbodrills for LANL in the 1970s to overcome motor temperature limitations. These turbodrills were used to drill the directional portions of LANL`s Hot Dry Rock Geothermal Wells at Fenton Hill, New Mexico. The Hot Dry Rock concept is to drill parallel inclined wells (35-degree inclination), hydraulically fracture between these wells, and then circulate cold water down one well and through the fractures and produce hot water out of the second well. At the time LANL drilled the Fenton Hill wells, the LANL turbodrill was the only motor in the world that would drill at the high temperatures encountered in these wells. It was difficult to operate the turbodrills continuously at low speed due to the low torque output of the LANL turbodrills. The turbodrills would stall frequently and could only be restarted by lifting the bit off bottom. This allowed the bit to rotate at very high speeds, and as a result, there was excessive wear in the bearings and on the gauge of insert roller bits due to these high rotary speeds. In 1998, Maurer Engineering developed an Advanced Geothermal Turbodrill (AGT) for the National Advanced Drilling and Excavation Technology (NADET) at MIT by adding a planetary speed reducer to the LANL turbodrill to increase its torque and reduce its rotary speed. Drilling tests were conducted with the AGT using 12 1/2-inch insert roller bits in Texas Pink Granite. The drilling tests were very successful, with the AGT drilling 94 ft/hr in Texas Pink Granite compared to 45 ft/hr with the LANL turbodrill and 42 ft/hr with a rotary drill. Field tests are currently being planned in Mexico and in geothermal wells in California to demonstrate the ability of the AGT to increase drilling rates and reduce drilling costs.

  15. Maximum Power Training and Plyometrics for Cross-Country Running.

    ERIC Educational Resources Information Center

    Ebben, William P.

    2001-01-01

    Provides a rationale for maximum power training and plyometrics as conditioning strategies for cross-country runners, examining: an evaluation of training methods (strength training and maximum power training and plyometrics); biomechanic and velocity specificity (role in preventing injury); and practical application of maximum power training and…

  16. Advanced Gas Turbine (AGT) Technology Project

    NASA Technical Reports Server (NTRS)

    1984-01-01

    Technical work on the design and effort leading to the testing of a 74.5 kW (100 hp) automotive gas turbine engine is reviewed. Development of the engine compressor, gasifier turbine, power turbine, combustor, regenerator, and secondary system is discussed. Ceramic materials development and the application of such materials in the gas turbine engine components is described.

  17. Advanced Gas Turbine (AGT) Technology Development Project annual report

    NASA Technical Reports Server (NTRS)

    1986-01-01

    This report is the tenth in a series of Technical Summary reports for the Advanced Gas Turbine (AGT) Technology Development Project, authorized under NASA Contract DEN3-167, and sponsored by the Department of Energy (DOE). This report was prepared by Garrett Turbine Engine Company, A Division of the Garrett Corporation, and includes information provided by Ford Motor Company, the Carborundum Company, and AiResearch Casting Company. The Project is administered by Mr. Thomas N. Strom, Project Manager, NASA-Lewis Research Center, Cleveland, Ohio. This report covers plans and progress for the period July 1, 1984 through June 30, 1985.

  18. Ceramic component development for the AGT101 gas turbine engine

    NASA Technical Reports Server (NTRS)

    Carruthers, W. D.; Smith, J. R.

    1984-01-01

    Under DOE/NASA sponsorship, a team is developing the AGT101, a highly efficient gas turbine engine for automotive application. The regenerated engine will operate at a maximum of 1370 C (2500 F) and 100,000 rpm, and will utilize a variety of Si3N4, SiC, lithium aluminum silicate and ceramic fiber insulation components. Engine design has been performed to consider the fabrication and material characteristics of these ceramic materials for both the static and rotating hot section components. Component fabrication has been performed, components have been screened in thermal and mechanical tests, and initial engine testing has been performed.

  19. Advanced Gas Turbine (AGT) technology development

    NASA Technical Reports Server (NTRS)

    1983-01-01

    A 74.5 kW (100 hp) automotive gas turbine was evaluated. The engine structure, bearings, oil system, and electronics were demonstrated and no shaft dynamics or other vibration problem were encountered. Areas identified during the five tests are the scroll retention features, and transient thermal deflection of turbine backplates. Modifications were designed. Seroll retention is addressed by modifying the seal arrangement in front of the gasifier turbine assembly, which will increase the pressure load on the scroll in the forward direction and thereby increase the retention forces. the backplate thermal deflection is addressed by geometric changes and thermal insulation to reduce heat input. Combustor rig proof testing of two ceramic combustor assemblies was completed. The combustor was modified to incorporate slots and reduce sharp edges, which should reduce thermal stresses. The development work focused on techniques to sinter these barrier materials onto the ceramic rotors with successes for both material systems. Silicon carbide structural parts, including engine configuration gasifier rotors (ECRs), preliminary gasifier scroll parts, and gasifier and power turbine vanes are fabricated.

  20. Thermophysical problems of the application freezing fuels for the aircraft gas-turbine engines (AGTE)

    SciTech Connect

    Janovsky, L.S.; Mitin, M.B.; Antonov, A.N.; Abashina, L.W.

    1996-12-31

    Authors of this paper analyzed results of mathematical researches of thermophysical problems of freezing and cryogenic fuels application for the aircraft gas-turbine engines (AGTE). These fuels are derived from hydrogen, propane, natural gas (methane) and oil gas (freezing mixture of hydrocarbons C{sub 2}-C{sub 10}). At present use of alternative fuels in AGTE is of great interest.

  1. AGT relations for abelian quiver gauge theories on ALE spaces

    NASA Astrophysics Data System (ADS)

    Pedrini, Mattia; Sala, Francesco; Szabo, Richard J.

    2016-05-01

    We construct level one dominant representations of the affine Kac-Moody algebra gl̂k on the equivariant cohomology groups of moduli spaces of rank one framed sheaves on the orbifold compactification of the minimal resolution Xk of the Ak-1 toric singularity C2 /Zk. We show that the direct sum of the fundamental classes of these moduli spaces is a Whittaker vector for gl̂k, which proves the AGT correspondence for pure N = 2 U(1) gauge theory on Xk. We consider Carlsson-Okounkov type Ext-bundles over products of the moduli spaces and use their Euler classes to define vertex operators. Under the decomposition gl̂k ≃ h ⊕sl̂k, these vertex operators decompose as products of bosonic exponentials associated to the Heisenberg algebra h and primary fields of sl̂k. We use these operators to prove the AGT correspondence for N = 2 superconformal abelian quiver gauge theories on Xk.

  2. Ventana{trade mark, serif} power train features and performance

    NASA Astrophysics Data System (ADS)

    Mohedano, R.; Benitez, P.; Zamora, P.; Miñano, J. C.; Mendes, J.; Cvetkovic, A.; Vilaplana, J.; Hernandez, M.; Chaves, J.; Biot, G.

    2013-09-01

    Most CPV systems are based on Fresnel lenses. Among these, LPI-patented Fresnel-Köhler (FK) concentrator outstands owing to performance and practical reasons. The Ventana{trade mark, serif} power train is the first off-the-shelf commercial product based on the FK and comprises both the primary (POE) lenses (a 36-units 1×1 m2 acrylic panel) and glass (or silica glass) secondary optics (SOE). This high concentration optical train (Cg=1,024×, ˜250mm optical depth) fits with 5×5 mm2 (at least) solar cells. The optical train is the fruit of a 1-year development that has included design, modeling, prototyping and characterization, and through the process we had the opportunity to find out how well the actual performance correlates with models, but also learned practical aspects of a CPV system of this kind, some of which have very positive impact on system performance and reliability.

  3. Preliminary power train design for a state-of-the-art electric vehicle

    NASA Technical Reports Server (NTRS)

    Mighdoll, P.; Hahn, W. F.

    1978-01-01

    Power train designs which can be implemented within the current state-of-the-art were identified by means of a review of existing electric vehicles and suitable off-the-shelf components. The affect of various motor/transmission combinations on vehicle range over the SAE J227a schedule D cycle was evaluated. The selected, state-of-the-art power train employs a dc series wound motor, SCR controller, variable speed transmission, regenerative braking, drum brakes and radial ply tires. Vehicle range over the SAE cycle can be extended by approximately 20% by the further development of separately excited, shunt wound DC motors and electrical controllers. Approaches which could improve overall power train efficiency, such as AC motor systems, are identified. However, future emphasis should remain on batteries, tires and lightweight structures if substantial range improvements are to be achieved.

  4. AUTOMOTIVE DIESEL MAINTENANCE 2. UNIT XXI, MICHIGAN/CLARK TRANSMISSION--COMPLETE POWER TRAIN.

    ERIC Educational Resources Information Center

    Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

    THIS MOSULE OF A 25-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF A SPECIFIC POWER TRAIN SYSTEM USED ON DIESEL POWERED EQUIPMENT. TOPICS ARE EXAMINING THE POWER FLOW, UNIT OIL FLOW, AND OIL PRESSURE IN THE CONVERTER AND TRANSMISSION SYSTEM. THE MODULE CONSISTS OF A SELF-INSTRUCTIONAL PROGRAM TRAINING FILM "UNDERSTANDING THE…

  5. Preliminary power train design for a state-of-the-art electric vehicle

    NASA Technical Reports Server (NTRS)

    Ross, J. A.; Wooldridge, G. A.

    1978-01-01

    The state-of-the-art (SOTA) of electric vehicles built since 1965 was reviewed to establish a base for the preliminary design of a power train for a SOTA electric vehicle. The performance of existing electric vehicles were evaluated to establish preliminary specifications for a power train design using state-of-the-art technology and commercially available components. Power train components were evaluated and selected using a computer simulation of the SAE J227a Schedule D driving cycle. Predicted range was determined for a number of motor and controller combinations in conjunction with the mechanical elements of power trains and a battery pack of sixteen lead-acid batteries - 471.7 kg at 0.093 MJ/Kg (1040 lbs. at 11.7 Whr/lb). On the basis of maximum range and overall system efficiency using the Schedule D cycle, an induction motor and 3 phase inverter/controller was selected as the optimum combination when used with a two-speed transaxle and steel belted radial tires. The predicted Schedule D range is 90.4 km (56.2 mi). Four near term improvements to the SOTA were identified, evaluated, and predicted to increase range approximately 7%.

  6. Advanced Gas Turbine (AGT) powertrain system development for automotive applications

    NASA Technical Reports Server (NTRS)

    1984-01-01

    Rotor dynamic instability investigations were conducted. Forward ball bearing hydraulic mount configurations were tested with little effect. Trial assembly of S/N 002 ceramic engine was initiated. Impeller design activities were completed on the straight line element (SLE) blade definition to address near-net-shape powder metal die forging. Performance characteristics of the Baseline Test 2A impeller were closely preserved. The modified blading design has been released for tooling procurement. Developmental testing of the diffusion flame combustor (DFC) for initial use in the S/N 002 2100 F ceramic structures engine was completed. A natural gas slave preheater was designed and fabricated. Preliminary regenerator static seal rig testing showed a significant reduction in leakage and sensitivity to stack height. Ceramic screening tests were completed and two complete sets of ceramic static structures were qualified for engine testing. Efforts on rotor dynamics development to resolve subsynchronous motion were continued.

  7. Towards the Proof of AGT Relations with the Help of the Generalized Jack Polynomials

    NASA Astrophysics Data System (ADS)

    Morozov, Alexei; Smirnov, Andrey

    2014-05-01

    Original proofs of the AGT relations with the help of the Hubbard-Stratanovich duality of the modified Dotsenko-Fateev matrix model did not work for β ≠ 1, because Nekrasov functions were not properly reproduced by Selberg-Kadell integrals of Jack polynomials. We demonstrate that if the generalized Jack polynomials, depending on the N-ples of Young diagrams from the very beginning, are used instead of the N-linear combinations of ordinary Jacks, this resolves the problem. Such polynomials naturally arise as special elements in the equivariant cohomologies of the GL( N)-instanton moduli spaces, and this also establishes connection to alternative ABBFLT approach to the AGT relations, studying the action of chiral algebras on the instanton moduli spaces. In this paper, we describe a complete proof of AGT in the simple case of GL(2) ( N = 2) Yang-Mills theory, i.e., the 4-point spherical conformal block of the Virasoro algebra.

  8. An experimental study of a PEM fuel cell power train for urban bus application

    NASA Astrophysics Data System (ADS)

    Corbo, P.; Migliardini, F.; Veneri, O.

    An experimental study was carried out on a fuel cell propulsion system for minibus application with the aim to investigate the main issues of energy management within the system in dynamic conditions. The fuel cell system (FCS), based on a 20 kW PEM stack, was integrated into the power train comprising DC-DC converter, Pb batteries as energy storage systems and asynchronous electric drive of 30 kW. As reference vehicle a minibus for public transportation in historical centres was adopted. A preliminary experimental analysis was conducted on the FCS connected to a resistive load through a DC-DC converter, in order to verify the stack dynamic performance varying its power acceleration from 0.5 kW s -1 to about 4 kW s -1. The experiments on the power train were conducted on a test bench able to simulate the vehicle parameters and road characteristics on specific driving cycles, in particular the European R40 cycle was adopted as reference. The "soft hybrid" configuration, which permitted the utilization of a minimum size energy storage system and implied the use of FCS mainly in dynamic operation, was compared with the "hard hybrid" solution, characterized by FCS operation at limited power in stationary conditions. Different control strategies of power flows between fuel cells, electric energy storage system and electric drive were adopted in order to verify the two above hybrid approaches during the vehicle mission, in terms of efficiencies of individual components and of the overall power train. The FCS was able to support the dynamic requirements typical of R40 cycle, but an increase of air flow rate during the fastest acceleration phases was necessary, with only a slight reduction of FCS efficiency. The FCS efficiency resulted comprised between 45 and 48%, while the overall power train efficiency reached 30% in conditions of constant stack power during the driving cycle.

  9. Inconsistency Across Time and Situations: A Decade of Research Using the Adjective Generation Technique (AGT).

    ERIC Educational Resources Information Center

    Allen, Bem P.; Potkay, Charles R.

    The Adjective Generation Technique (AGT) has been used in studies to demonstrate that subjects' responses show variations from one point in time to the next. To examine this hypothesis, longitudinal studies were undertaken where subjects were asked to generate five words to describe themselves on each of 29 days. Some conclusions drawn were that:…

  10. Association of AGT M235T gene polymorphism with HSP/HSPN risk.

    PubMed

    Mao, Song; Huang, Songming

    2015-02-01

    To evaluate the association between angiotensinogen (AGT) gene polymorphism and the risk of Henoch-Schönlein purpura (HSP)/Henoch-Schönlein purpura nephritis (HSPN) we searched the eligible studies through Pub Med, Embase, Cochrane, and China National Knowledge Infrastructure (CNKI) databases according to predefined criteria. A random-effects model was used to calculate the combined odds ratios (ORs) and its corresponding 95% confidence interval (CI). Five studies were recruited for the analysis of the association between AGT M235T gene polymorphism and HSP/HSPN risk. M allele was associated with lower risk of HSP in adult (p = 0.050), TT genotype was associated with the susceptibility to HSP in adult (p = 0.039). AGT M235T gene polymorphism was not associated with HSP risk in children. No marked association was observed between AGT M235T gene polymorphism and HSPN risk. No evidence of publication bias was observed. In conclusion, M allele might be a protective factor against the HSP risk in adult, TT genotype might be a risk factor for the susceptibility to HSP in adult. However, further larger studies should be performed in the future. PMID:25350836

  11. Experimental study of a fuel cell power train for road transport application

    NASA Astrophysics Data System (ADS)

    Corbo, P.; Corcione, F. E.; Migliardini, F.; Veneri, O.

    The development of fuel cell electric vehicles requires the on-board integration of fuel cell systems and electric energy storage devices, with an appropriate energy management system. The optimization of performance and efficiency needs an experimental analysis of the power train, which has to be effected in both stationary and transient conditions (including standard driving cycles). In this paper experimental results concerning the performance of a fuel cell power train are reported and discussed. In particular characterization results for a small sized fuel cell system (FCS), based on a 2.5 kW PEM stack, alone and coupled to an electric propulsion chain of 3.7 kW are presented and discussed. The control unit of the FCS allowed the main stack operative parameters (stoichiometric ratio, hydrogen and air pressure, temperature) to be varied and regulated in order to obtain optimized polarization and efficiency curves. Experimental runs effected on the power train during standard driving cycles have allowed the performance and efficiency of the individual components (fuel cell stack and auxiliaries, dc-dc converter, traction batteries, electric engine) to be evaluated, evidencing the role of output current and voltage of the dc-dc converter in directing the energy flows within the propulsion system.

  12. Dynamic behaviour of Li batteries in hydrogen fuel cell power trains

    NASA Astrophysics Data System (ADS)

    Veneri, O.; Migliardini, F.; Capasso, C.; Corbo, P.

    A Li ion polymer battery pack for road vehicles (48 V, 20 Ah) was tested by charging/discharging tests at different current values, in order to evaluate its performance in comparison with a conventional Pb acid battery pack. The comparative analysis was also performed integrating the two storage systems in a hydrogen fuel cell power train for moped applications. The propulsion system comprised a fuel cell generator based on a 2.5 kW polymeric electrolyte membrane (PEM) stack, fuelled with compressed hydrogen, an electric drive of 1.8 kW as nominal power, of the same typology of that installed on commercial electric scooters (brushless electric machine and controlled bidirectional inverter). The power train was characterized making use of a test bench able to simulate the vehicle behaviour and road characteristics on driving cycles with different acceleration/deceleration rates and lengths. The power flows between fuel cell system, electric energy storage system and electric drive during the different cycles were analyzed, evidencing the effect of high battery currents on the vehicle driving range. The use of Li batteries in the fuel cell power train, adopting a range extender configuration, determined a hydrogen consumption lower than the correspondent Pb battery/fuel cell hybrid vehicle, with a major flexibility in the power management.

  13. The Adipose Renin-Angiotensin System Modulates Systemic Markers of Insulin Sensitivity and Activates the Intrarenal Renin-Angiotensin System

    DOE PAGESBeta

    Kim, Suyeon; Soltani-Bejnood, Morvarid; Quignard-Boulange, Annie; Massiera, Florence; Teboul, Michele; Ailhaud, Gerard; Kim, Jung Han; Moustaid-Moussa, Naima; Voy, Brynn H.

    2006-01-01

    Background . The adipose tissue renin-angiotensin system (RAS) contributes to regulation of fat mass and may also impact systemic functions such as blood pressure and metabolism. Methods and results . A panel of mouse models including mice lacking angiotensinogen, Agt ( Agt -KO), mice expressing Agt solely in adipose tissue (aP2- Agt/Agt -KO), and mice overexpressing Agt in adipose tissue (aP2- Agt ) was studied. Total body weight, epididymal fat pad weight, and circulating levels of leptin, insulin, and resistin were significantly decreased in Agt -KO mice, while plasma adiponectin levels were increased. aP2- Agt mice exhibited increased adipositymore » and plasma leptin and insulin levels compared to wild type (WT) controls. Angiotensinogen and type I Ang II receptor protein levels were also elevated in kidney of aP2- Agt mice. Conclusion . These findings demonstrate that alterations in adipose RAS activity significantly impact both local and systemic physiology in a way that may contribute to the detrimental health effects of obesity.« less

  14. Identification of regulatory elements in the AGT1 promoter of ale and lager strains of brewer's yeast.

    PubMed

    Vidgren, Virve; Kankainen, Matti; Londesborough, John; Ruohonen, Laura

    2011-08-01

    Agt1 is an interesting α-glucoside transporter for the brewing industry, as it efficiently transports maltotriose, a sugar often remaining partly unused during beer fermentation. It has been shown that on maltose the expression level of AGT1 is much higher in ale strains than in lager strains, and that glucose represses the expression, particularly in the ale strains. In the present study the regulatory elements of the AGT1 promoter of one ale and two lager strains were identified by computational methods. Promoter regions up to 1.9 kbp upstream of the AGT1 gene were sequenced from the three brewer's yeast strains and the laboratory yeast strain CEN.PK-1D. The promoter sequence of the laboratory strain was identical to the AGT1 promoter of strain S288c of the Saccharomyces Genome Database, whereas the promoter sequences of the industrial strains diverged markedly from the S288c strain. The AGT1 promoter regions of the ale and lager strains were for the most part identical to each other, except for one 22 bp deletion and two 94 and 95 bp insertions in the ale strain. Computational analyses of promoter elements revealed that the promoter sequences contained several Mig1- and MAL-activator binding sites, as was expected. However, some of the Mig1 and MAL-activator binding sites were located on the two insertions of the ale strain, and thus offered a plausible explanation for the different expression pattern of the AGT1 gene in the ale strains. Accordingly, functional analysis of A60 ale and A15 lager strain AGT1 promoters fused to GFP (encoding the green fluorescent protein) showed a significant difference in the ability of these two promoters to drive GFP expression. Under the control of the AGT1 promoter of the ale strain the emergence of GFP was strongly induced by maltose, whereas only a low level of GFP was detected with the construct carrying the AGT1 promoter of the lager strain. Thus, the extra MAL-activator binding element, present in the AGT1 promoter of

  15. Angiotensinogen (AGT) M235T, AGT T174M and Angiotensin-1-Converting Enzyme (ACE) I/D Gene Polymorphisms in Essential Hypertension: Effects on Ramipril Efficacy

    PubMed Central

    Kolovou, Vana; Lagou, Evangelia; Mihas, Constantinos; Vasiliki, Giannakopoulou; Katsiki, Niki; Kollia, Aikaterini; Triposkiadis, Filippos; Degiannis, Dimitris; Mavrogeni, Sophie; Kolovou, Genovefa

    2015-01-01

    Background: Hypertension, one of the most important risk factors for premature cardiovascular disease, is a major worldwide public health problem. Angiotensin-1-converting enzyme (ACE) and angiotensinogen (AGT) gene polymorphisms are thought to be associated with primary hypertension. In the present study, we examined the frequency of these gene polymorphisms in an adult population with and without essential hypertension. Furthermore, we evaluated the effect of ACE and AGT gene polymorphisms on ramipril treatment efficacy in the hypertensive patients. Methods: A total of 166 adults (83 hypertensives and 83 normotensives) were involved in the study and genotyped for AGTM235T (rs699), AGTT174M (rs4762) and ACEI/D (rs1799752) gene polymorphisms. Results: The genotype and allele distribution of the AGTM235T variant significantly differed between hypertensives and normotensives [odds ratio (OR) = 1.57% (T vs M allele), 95% confidence intervals (CIs): 1.01 - 2.44; p=0.045 for hypertensives]. However, none of the 3 studied Simple Nucleotide Polymorphisms were associated with the blood pressure-lowering response to ramipril. Conclusion: These results suggest that AGTM235T gene polymorphism is associated with essential hypertension. However, none of the AGTM235T, AGTT174M and ACEI/D gene polymorphisms influenced ramipril effectiveness. PMID:27006715

  16. Three Agt1 transporters from brewer's yeasts exhibit different temperature dependencies for maltose transport over the range of brewery temperatures (0–20 °C).

    PubMed

    Vidgren, Virve; Viljanen, Kaarina; Mattinen, Laura; Rautio, Jari; Londesborough, John

    2014-06-01

    Zero-trans rates of maltose transport by brewer's yeasts exert strong control over fermentation rates and are strongly temperature-dependent over the temperature range (20–0 °C) of brewery fermentations. Three α-glucoside transporters, ScAgt1(A60) (a Saccharomyces cerevisiae version of Agt1 from an ale strain), ScAgt1-A548V (a variant of ScAgt1(A60) with a single amino acid change in a transmembrane domain), and SbAgt1 (a Saccharomyces (eu)bayanus version from a lager strain), were compared. When expressed in the same laboratory yeast, grown at 24 °C and assayed at 0, 10, and 20 °C, SbAgt1 had the lowest absolute maltose uptake activity at 20 °C but smallest temperature dependence, ScAgt1-A548V had the highest activity but greatest temperature dependence, and ScAgt1(A60) had intermediate properties. ScAgt1(A60) exhibited higher absolute rates and smaller temperature dependencies when expressed in laboratory rather than brewer's strains. Absolute rates closely reflected the amounts of GFP-tagged ScAgt1(A60) transporter in each host's plasma membrane. Growth at 15 °C instead of 24 °C decreased the absolute activities of strains expressing ScAgt1(A60) by two- to threefold. Evidently, the kinetic characteristics of at least ScAgt1(A60) depended on the nature of the host plasma membrane. However, no consistent correlation was observed between transport activities and fatty acid or ergosterol compositions. PMID:25035870

  17. Power train for front and rear wheel drive vehicle

    SciTech Connect

    Matsuda, M.; Shinozaki, T.

    1987-05-19

    This patent describes a power train for a front and rear wheel drive vehicle comprising: an engine having a crankshaft and an engine case; a first output shaft on a first side of the crankshaft and parallel thereto in the engine case; a second output shaft on a second side to the crankshaft and parallel thereto in the engine case; and a speed change transmission coupled between the crankshaft and the second output shaft, the first output shaft being driven by the second output shaft.

  18. Oligodeoxynucleotides as substrates for O/sup 6/-alkylguanine-DNA alkyltransferase (AGT)

    SciTech Connect

    Scicchitano, D.; Jones, R.A.; Kuzmich, S.; Gaffney, B.; Lasko, D.; Essigmann, J.; Pegg, A.E.

    1986-05-01

    AGT is a DNA repair protein which is known to catalyze the transfer of alkyl groups from the O/sup 6/-position of guanine in alkylated DNA to a cysteine acceptor site contained within its own protein sequence. The authors have examined the ability of this protein isolated from both E. coli and mammalian cells to carry out this reaction using oligodeoxynucleotides containing O/sup 6/-methylguanine (m/sup 6/G). Dodecadeoxynucleotides of the sequence 5'-dCGBGAATTCm/sup 6/GCG-3' where B is any one of the normal 4 bases were all repaired very rapidly with 50% repair in less than 15 sec at 0/sup 0/C. The hexadeoxynucleotide 5'-dCGCm/sup 6/GCG-3' was repaired slightly more slowly with 50% removal requiring 7 min at 0/sup 0/C and 1.5 min at 37/sup 0/C. The tetradeoxynucleotide 5'-dTm/sup 6/GCA-3' was also a substrate for the protein but was repaired much more slowly requiring 45 min for 50% repair at 37/sup 0/C. These results indicate that (a) the AGT has a strong but not absolute preference for double stranded DNA substrates; (b) the repair of m/sup 6/G is independent of the base opposite the lesion; and (c) that very short oligodeoxynucleotides are substrates for repair by this protein. The latter property was used to set up a very sensitive assay procedure for the AGT. The 5' end of the 5'-dTm/sup 6/GCA-3' was labeled with /sup 32/P by use of polynucleotide kinase and the formation of (/sup 32/P)-5'-dTGACA-3' monitored by separating the methylated form from the unmethylated form by HPLC.

  19. 4-Nitrobenzyloxycarbonyl Derivatives of O6-Benzylguanine as Hypoxia-Activated Prodrug Inhibitors of O6-Alkylguanine-DNA Alkyltransferase (AGT) which Produces Resistance to Agents Targeting the O-6 Position of DNA Guanine

    PubMed Central

    Zhu, Rui; Liu, Mao-Chin; Luo, Mei-Zhen; Penketh, Philip G.; Baumann, Raymond P.; Shyam, Krishnamurthy; Sartorelli, Alan C.

    2011-01-01

    A series of 4-nitrobenzyloxycarbonyl prodrug derivatives of O6-benzylguanine (O6-BG), conceived as prodrugs of O6-BG, an inhibitor of the resistance protein O6-alkylguanine-DNA alkyltransferase (AGT), were synthesized and evaluated for their ability to undergo bioreductive activation by reductase enzymes under oxygen deficiency. Three agents of this class, 4-nitrobenzyl (6-(benzyloxy)-9H-purin-2-yl)carbamate (1), and its monomethyl (2) and gem-dimethyl analogues (3) were tested for activation by reductase enzyme systems under oxygen deficient conditions. Compound 3, the most water-soluble of these agents, gave the highest yield of O6-BG following reduction of the nitro group trigger. Compound 3 was also evaluated for its ability to sensitize 1,2-bis(methylsulfonyl)-1-(2-chloroethyl)-2-[(methylamino)carbonyl]hydrazine (laromustine)-resistant DU145 human prostate carcinoma cells, which express high levels of AGT, to the cytotoxic effects of this agent under normoxic and oxygen deficient conditions. While 3 had little or no effect on laromustine cytotoxicity under aerobic conditions, significant enhancement occurred under oxygen deficiency, providing evidence for the preferential release of the AGT inhibitor O6-BG under hypoxia. PMID:21955333

  20. Generalized Macdonald polynomials, spectral duality for conformal blocks and AGT correspondence in five dimensions

    NASA Astrophysics Data System (ADS)

    Zenkevich, Yegor

    2015-05-01

    We study five dimensional AGT correspondence by means of the q-deformed beta-ensemble technique. We provide a special basis of states in the q-deformed CFT Hilbert space consisting of generalized Macdonald polynomials, derive the loop equations for the beta-ensemble and obtain the factorization formulas for the corresponding matrix elements. We prove the spectral duality for SU(2) Nekrasov functions and discuss its meaning for conformal blocks. We also clarify the relation between topological strings and q-Liouville vertex operators.

  1. Preliminary power train design for a state-of-the-art electric vehicle (executive summary)

    NASA Technical Reports Server (NTRS)

    1978-01-01

    The preliminary design of a state-of-the-art electric power train is part of a national effort to reap the potential benefit of useful urban electric passenger vehicles. Outlined in a detailed presentation are: (1) assessment of the state-of-the-art in electric vehicle technology; (2) state-of-the-art power train design; (3) improved power train; and (4) summary and recommendations.

  2. Performance test results for the Eaton dc development power train in an electric test bed vehicle

    NASA Astrophysics Data System (ADS)

    Crumley, R. L.; Donaldson, M. R.

    1987-09-01

    This report presents the results of the tests performed on a direct current (dc) power train in a test bed vehicle developed by the Eaton Corporation for the U.S. Department of Energy (DOE). The tests were performed by EG and G Idaho, Inc. at the Idaho National Engineering Laboratory (INEL). The purpose of the INEL testing was to provide test results from which an evaluation of the performance capabilities of the Eaton dc power train could be made and compared with other vehicle propulsion systems. The planned tests were primarily oriented toward road testing, chassis dynamometer testing, and associated dynamometer coastdown tests for road loss determination. Range tests of the Eaton dc test bed vehicle using an ALCO 2200 lead acid battery pack, produced ranges of 97 km at 56 km/h (60 miles at 35 mph), 79 km at 72 km/h (49 miles at 45 mph), and 47 km at 88 km/h (29 miles at 55 mph). The corresponding net dc energy consumptions are 135 Wh/km (217 Wh/mile), 145 Wh/km (233 Wh/mile), and 178 Wh/km (287 Wh/mile). The energy consumption for the D-cycle test was 241 Wh/km (387 Wh/mile).

  3. Association between G-217A polymorphism in the AGT gene and essential hypertension: a meta-analysis.

    PubMed

    Yao, R; Du, Y Y; Zhang, Y Z; Chen, Q H; Zhao, L S; Li, L

    2015-01-01

    Numerous studies have evaluated the association between the angiotensinogen (AGT) G-217A gene polymorphism and essential hypertension risk. However, the results have been inconsistent. We examined whether the AGT G-217A gene polymorphism confers essential hypertension risk by conducting a meta-analysis. We conducted a literature search of the Google Scholar, PubMed, and China National Knowledge Infrastructure databases for relevant studies that examined the G-217A polymorphism and risk of essential hypertension. Statistical analyses were carried out using Stata 12.0 to combine all relevant studies. Crude odds ratios (ORs) with 95% confidence intervals (95%CIs) were calculated to estimate the strength of this association. A total of 2017 patients with psoriasis and 1708 controls from 7 comparative studies were included in this meta-analysis. We found a significant association between the AGT G-217A gene polymorphism and the risk of essential hypertension (AA vs GG: OR = 2.52, 95%CI = 1.68-3.78; AA vs GA: OR = 2.26, 95%CI = 1.48-3.45; dominant model: OR = 0.38, 95%CI = 0.26-0.57; recessive model: OR = 1.20, 95%CI = 1.03-1.39). Further stratified analyses were conducted by ethnicity and sample size and produced similar results. No evidence of publication bias was found. This meta-analysis confirms that the AGT G-217A gene polymorphism is associated with essential hypertension susceptibility. PMID:26125750

  4. ATTAP/AGT101 - Year 2 progress in ceramic technology development

    NASA Technical Reports Server (NTRS)

    Kidwell, J. R.; Lindberg, L. J.; Morey, R. E.

    1990-01-01

    The progress made by the Advanced Turbine Technology Applications Project (ATTAP) is summarized, with emphasis on the following areas: ceramic materials assessment and characterization, ceramic impact damage assessment, ceramic combustor evaluation, turbine inlet particle separator development, impact-tolerant turbine designs, and net-shape ceramic component fabrications. In the evolutionary ceramics development in the Automotive Gas Turbine (AGT101) and ATTAP programs initial designs were conceived to reduce stresses by using well-established criteria: bodies of revolution were preferred over nonaxisymmetric geometries, sharp corners were avoided, the contact area between components was kept as large as possible, and small parts were preferred over large when feasible. Projects discussed include: initial ceramic component fabrication by ceramic suppliers in 1990, engine test to 1371 C in 1991, 100-hr test bed engine durability test in 1991, and 300-hr test bed engine durability in 1992.

  5. The adipose renin-angiotensin system modulates sysemic markers of insulin sensitivity activates the intrarenal renin-angiotensin system

    SciTech Connect

    Kim, Suyeon; Soltani-Bejnood, Morvarid; Quignard-Boulange, Annie; Massiera, Florence; Teboul, Michele; Ailhaud, Gerard; Kim, Jung; Moustaid-Moussa, Naima; Voy, Brynn H

    2006-07-01

    BACKGROUND: A growing body of data provides increasing evidence that the adipose tissue renin-angiotensin system (RAS) contributes to regulation of fat mass. Beyond its paracrine actions within adipose tissue, adipocyte-derived angiotensin II (Ang II) may also impact systemic functions such as blood pressure and metabolism. METHODS AND RESULTS: We used a genetic approach to manipulate adipose RAS activity in mice and then study the consequences on metabolic parameters and on feedback regulation of the RAS. The models included deletion of the angiotensinogen (Agt) gene (Agt-KO), its expression solely in adipose tissue under the control of an adipocyte-specific promoter (aP2-Agt/ Agt-KO), and overexpression in adipose tissue of wild type mice (aP2-Agt). Total body weight, epididymal fat pad weight, and circulating levels of leptin, insulin and resistin were significantly decreased in Agt-KO mice, while plasma adiponectin levels were increased. Overexpression of Agt in adipose tissue resulted in increased adiposity and plasma leptin and insulin levels compared to wild type (WT) controls. Angiotensinogen and type I Ang II receptor protein levels were also markedly elevated in kidney of aP2-Agt mice, suggesting that hypertension in these animals may be in part due to stimulation of the intrarenal RAS. CONCLUSIONS: Taken together, the results from this study demonstrate that alterations in adipose RAS activity significantly alter both local and systemic physiology in a way that may contribute to the detrimental health effects of obesity.

  6. Novel regulation of Skp1 by the Dictyostelium AgtA α-galactosyltransferase involves the Skp1-binding activity of its WD40 repeat domain.

    PubMed

    Schafer, Christopher M; Sheikh, M Osman; Zhang, Dongmei; West, Christopher M

    2014-03-28

    The role of Skp1 as an adaptor protein that links Cullin-1 to F-box proteins in E3 Skp1/Cullin-1/F-box protein (SCF) ubiquitin ligases is well characterized. In the social amoeba Dictyostelium and probably many other unicellular eukaryotes, Skp1 is modified by a pentasaccharide attached to a hydroxyproline near its C terminus. This modification is important for oxygen-sensing during Dictyostelium development and is mediated by a HIF-α type prolyl 4-hydroxylase and five sequentially acting cytoplasmic glycosyltransferase activities. Gene disruption studies show that AgtA, the enzyme responsible for addition of the final two galactose residues, in α-linkages to the Skp1 core trisaccharide, is unexpectedly critical for oxygen-dependent terminal development. AgtA possesses a WD40 repeat domain C-terminal to its single catalytic domain and, by use of domain deletions, binding studies, and enzyme assays, we find that the WD40 repeats confer a salt-sensitive second-site binding interaction with Skp1 that mediates novel catalytic activation in addition to simple substrate recognition. In addition, AgtA binds similarly well to precursor isoforms of Skp1 by a salt-sensitive mechanism that competes with binding to an F-box protein and recognition by early modification enzymes, and the effect of binding is diminished when AgtA modifies Skp1. Genetic studies show that loss of AgtA is more severe when an earlier glycosylation step is blocked, and overexpressed AgtA is deleterious if catalytically inactivated. Together, the findings suggest that AgtA mediates non-enzymatic control of unmodified and substrate precursor forms of Skp1 by a binding mechanism that is normally relieved by switch-like activation of its glycosylation function. PMID:24550398

  7. Use of blade pitch control to provide power train damping for the Mod-2, 2.5-mW wind turbine

    NASA Technical Reports Server (NTRS)

    Blissell, W. A., Jr.

    1995-01-01

    The Control System for the Mod-2 wind turbine system is required to provide not only for startup, RPM regulation, maximizing or regulating power, and stopping the rotor, but also for load limiting, especially in the power train. Early operations with above-rated winds revealed an instability which was caused primarily by coupling between the quill shaft and the rotor air loads. This instability caused the first of several major Mod-2 Control System changes which are reviewed in the paper.

  8. Use of blade pitch control to provide power train damping for the Mod-2, 2.5-mW wind turbine

    NASA Astrophysics Data System (ADS)

    Blissell, W. A., Jr.

    1995-05-01

    The Control System for the Mod-2 wind turbine system is required to provide not only for startup, RPM regulation, maximizing or regulating power, and stopping the rotor, but also for load limiting, especially in the power train. Early operations with above-rated winds revealed an instability which was caused primarily by coupling between the quill shaft and the rotor air loads. This instability caused the first of several major Mod-2 Control System changes which are reviewed in the paper.

  9. Optimizing Soft Magnetic Composites for Power Frequency Applications and Power-Trains

    NASA Astrophysics Data System (ADS)

    Lemieux, Patrick; Guthrie, Roderick; Isac, Mihaiela

    2012-03-01

    A new approach, together with a new family of soft magnetic composites (SMCs), has been developed and optimized for power alternating-current applications. The different technological and economic restrictions needed to maximize a composite's performance-to-cost ratio are presented. The experimental procedures to produce sintered lamellar SMCs are reported, together with magnetic results and the effects of different processing parameters on their performance. The present results are compared with corresponding data available for soft magnetic materials available on the market (laminations and composites). Data on the mechanical strength of these new SMC structures are also given. The new process results in magnetic and mechanical properties of different alloy systems that are better than those of any of the SMCs available. The present materials' energetic losses can be under 2 W/kg at 60 Hz, at 1 T, whilst their permeability exceeds 2000, while maintaining maximum induction above 1.7 T. These properties are very close to the best results for standard laminations on the market. The present process has the potential to be very inexpensive, owing to its simplicity. Even though not fully isotropic, recent three-dimensional machine designs and process advantages conferred by powder metallurgy techniques can be applied to this new family of lamellar particle composites. Through theoretical calculations and modeling exercises, it is briefly shown that this new kind of material can result in an improvement to the transportation sector where weight and efficiency of newly emerging electrical and hybrid power-trains are of prime importance.

  10. Neuromuscular Characteristics of Endurance--And Power-Trained Athletes

    ERIC Educational Resources Information Center

    Koceja, David M.; Davison, Edwin; Robertson, Christopher T.

    2004-01-01

    In response to chronic physical training, the human neuromuscular system undergoes significant and specific adaptations. More importantly, these influences are the result of the type and quantity of physical activity. One of the simplest neuromuscular mechanisms is the spinal stretch reflex. The reflex system was previously viewed as inflexible,…

  11. Strength and power training: physiological mechanisms of adaptation.

    PubMed

    Kraemer, W J; Fleck, S J; Evans, W J

    1996-01-01

    Adaptations in resistance training are focused on the development and maintenance of the neuromuscular unit needed for force production [97, 136]. The effects of training, when using this system, affect many other physiological systems of the body (e.g., the connective tissue, cardiovascular, and endocrine systems) [16, 18, 37, 77, 83]. Training programs are highly specific to the types of adaptation that occur. Activation of specific patterns of motor units in training dictate what tissue and how other physiological systems will be affected by the exercise training. The time course of the development of the neuromuscular system appears to be dominated in the early phase by neural factors with associated changes in the types of contractile proteins. In the later adaptation phase, muscle protein increases, and the contractile unit begins to contribute the most to the changes in performance capabilities. A host of other factors can affect the adaptations, such as functional capabilities of the individual, age, nutritional status, and behavioral factors (e.g., sleep and health habits). Optimal adaptation appears to be related to the use of specific resistance training programs to meet individual training objectives. PMID:8744256

  12. Combinatorial Study of Ag-Te Thin Films and Their Application as Cation Supply Layer in CBRAM Cells.

    PubMed

    Devulder, Wouter; Opsomer, Karl; Meersschaut, Johan; Deduytsche, Davy; Jurczak, Malgorzata; Goux, Ludovic; Detavernier, Christophe

    2015-05-11

    In this work, we investigate binary Ag-Te thin films and their functionality as a cation supply layer in conductive bridge random access memory devices. A combinatorial sputter deposition technique is used to deposit a graded Ag(x)Te(1-x) (0 < x < 1) layer with varying composition as a function of the position on the substrate. The crystallinity, surface morphology, and material stability under thermal treatment as a function of the composition of the material are investigated. From this screening, a narrow composition range between 33 and 38 at% Te is selected which shows a good morphology and a high melting temperature. Functionality of a single Ag(2-δ)Te composition as cation supply layer in CBRAM with dedicated Al2O3 switching layer is then investigated by implementing it in 580 μm diameter dot Pt/Ag(2-δ)Te/Al2O3/Si cells. Switching properties are investigated and compared to cells with a pure Ag cation supply layer. An improved cycling behavior is observed when Te is added compared to pure Ag, which we relate to the ionic conducting properties of Ag2Te and the preferred formation of Ag-Te phases. PMID:25860668

  13. Lower Extremity Power Training in Elderly Subjects with Mobility Limitations: A Randomized Controlled Trial

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Background and Aims This study investigated whether high-velocity high-power training (POW) improved lower extremity muscle power and quality in functionally-limited elders greater than traditional slow-velocity progressive resistance training (STR). Methods Fifty-seven community-dwelling older adul...

  14. Lower extremity power training in elderly subjects with moderate mobility limitations: A randomized controlled trial

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Fifty-seven community-dwelling older adults were randomized to either high-velocity high-power training (POW), slow-velocity progressive resistance training (STR) or a control group of lower extremity stretching (CON). Training was performed three times per week for 12 weeks and subjects completed t...

  15. LOWER EXTREMITY PEAK POWER TRAINING IN ELDERLY SUBJECTS WITH MODERATE MOBILITY LIMITATIONS: A RANDOMIZED CONTROLLED TRIAL

    Technology Transfer Automated Retrieval System (TEKTRAN)

    To examine the effects of a lower extremity high-velocity high-power exercise training intervention in older adults with moderate mobility impairments, and to investigate whether peak power training results in greater increases of peak muscle power output compared to traditional progressive resistan...

  16. Baseline tests of the power-train electric delivery van

    NASA Technical Reports Server (NTRS)

    Lumannick, S.; Dustin, M. O.; Bozek, J. M.

    1977-01-01

    Vehicle maximum speed, range at constant speed, range over stop-and-go driving schedules, maximum acceleration, gradeability, gradeability limit, road energy consumption, road power, indicated energy consumption, braking capability, battery charger efficiency, and battery characteristics were determined for a modified utility van powered by sixteen 6-volt batteries connected in series. A chopper controller actuated by a foot accelerator pedal changes the voltage applied to the 22-kilowatt (30-hp) series-wound drive motor. In addition to the conventional hydraulic braking system, the vehicle has hydraulic regenerative braking. Cycle tests and acceleration tests were conducted with and without hydraulic regeneration.

  17. Effect of a Periodized Power Training Program on the Functional Performances and Contractile Properties of the Quadriceps in Sprinters

    ERIC Educational Resources Information Center

    Kamandulis, Sigitas; Skurvydas, Albertas; Brazaitis, Marius; Stanislovaitis, Aleksas; Duchateau, Jacques; Stanislovaitiene, Jurate

    2012-01-01

    Our purpose was to compare the effect of a periodized preparation consisting of power endurance training and high-intensity power training on the contractile properties of the quadriceps muscle and functional performances in well trained male sprinters (n = 7). After 4 weeks of high-intensity power training, 60-m sprint running time improved by an…

  18. 76 FR 22729 - Chrysler Group, LLC, Power Train Division, Mack Avenue Engine Plant #1, Including On-Site Leased...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-04-22

    ... December 18, 2008 (73 FR 77067). In order to avoid an overlap in worker group coverage, the Department is... Employment and Training Administration Chrysler Group, LLC, Power Train Division, Mack Avenue Engine Plant 1..., LLC, Power Train Division, Mack Avenue Engine Plant 1, including on-site leased workers of...

  19. Caenorhabditis elegans AGXT-1 is a mitochondrial and temperature-adapted ortholog of peroxisomal human AGT1: New insights into between-species divergence in glyoxylate metabolism.

    PubMed

    Mesa-Torres, Noel; Calvo, Ana C; Oppici, Elisa; Titelbaum, Nicholas; Montioli, Riccardo; Miranda-Vizuete, Antonio; Cellini, Barbara; Salido, Eduardo; Pey, Angel L

    2016-09-01

    In humans, glyoxylate is an intermediary product of metabolism, whose concentration is finely balanced. Mutations in peroxisomal alanine:glyoxylate aminotransferase (hAGT1) cause primary hyperoxaluria type 1 (PH1), which results in glyoxylate accumulation that is converted to toxic oxalate. In contrast, glyoxylate is used by the nematode Caenorhabditis elegans through a glyoxylate cycle to by-pass the decarboxylation steps of the tricarboxylic acid cycle and thus contributing to energy production and gluconeogenesis from stored lipids. To investigate the differences in glyoxylate metabolism between humans and C. elegans and to determine whether the nematode might be a suitable model for PH1, we have characterized here the predicted nematode ortholog of hAGT1 (AGXT-1) and compared its molecular properties with those of the human enzyme. Both enzymes form active PLP-dependent dimers with high specificity towards alanine and glyoxylate, and display similar three-dimensional structures. Interestingly, AGXT-1 shows 5-fold higher activity towards the alanine/glyoxylate pair than hAGT1. Thermal and chemical stability of AGXT-1 is lower than that of hAGT1, suggesting temperature-adaptation of the nematode enzyme linked to the lower optimal growth temperature of C. elegans. Remarkably, in vivo experiments demonstrate the mitochondrial localization of AGXT-1 in contrast to the peroxisomal compartmentalization of hAGT1. Our results support the view that the different glyoxylate metabolism in the nematode is associated with the divergent molecular properties and subcellular localization of the alanine:glyoxylate aminotransferase activity. PMID:27179589

  20. Rule Extracting based on MCG with its Application in Helicopter Power Train Fault Diagnosis

    NASA Astrophysics Data System (ADS)

    Wang, M.; Hu, N. Q.; Qin, G. J.

    2011-07-01

    In order to extract decision rules for fault diagnosis from incomplete historical test records for knowledge-based damage assessment of helicopter power train structure. A method that can directly extract the optimal generalized decision rules from incomplete information based on GrC was proposed. Based on semantic analysis of unknown attribute value, the granule was extended to handle incomplete information. Maximum characteristic granule (MCG) was defined based on characteristic relation, and MCG was used to construct the resolution function matrix. The optimal general decision rule was introduced, with the basic equivalent forms of propositional logic, the rules were extracted and reduction from incomplete information table. Combined with a fault diagnosis example of power train, the application approach of the method was present, and the validity of this method in knowledge acquisition was proved.

  1. Feasibility of eyes open alpha power training for mental enhancement in elite gymnasts.

    PubMed

    Dekker, Marian K J; van den Berg, Berber R; Denissen, Ad J M; Sitskoorn, Margriet M; van Boxtel, Geert J M

    2014-01-01

    This study focuses on a novel, easy to use and instruction-less method for mental training in athletes. Previous findings suggest that particular mental capacities are needed for achieving peak performance; including attentional control, focus, relaxation and positive affect. Electroencephalography (EEG) alpha brain activity has been associated with neural inhibition during processes of selective attention, for improving efficiency in information processing. Here we hypothesised that eyes open alpha power training by music teaches athletes to (1) learn to self-regulate their brain activity, and (2) learn to increase their baseline alpha power, herewith improving mental capacities such as focusing the allocation of attention. The study was double-blind and placebo-controlled. Twelve elite gymnasts were either given eyes open alpha power training or random beta power training (controls). Results indicate small improvements in sleep quality, mental and physical shape. In our first attempt at getting a grip on mental capacities in athletes, we think this novel training method can be promising. Because gymnastics is one of the most mentally demanding sports, we value even small benefits for the athlete and consider them indicative for future research. PMID:24784756

  2. The Effects of POWER Training in Young and Older Adults after Stroke.

    PubMed

    Hunnicutt, Jennifer L; Aaron, Stacey E; Embry, Aaron E; Cence, Brian; Morgan, Patrick; Bowden, Mark G; Gregory, Chris M

    2016-01-01

    Background. Approximately 35,000 strokes occur annually in adults below the age of 40, and there is disappointingly little data describing their responses to rehabilitation. The purpose of this analysis was to determine the effects of Poststroke Optimization of Walking using Explosive Resistance (POWER) training in young (<40 years) and older (>60 years) adults and to describe relationships between training-induced improvements in muscular and locomotor function. Methods. Data was analyzed from 16 individuals with chronic stroke who participated in 24 sessions of POWER training. Outcomes included muscle power generation, self-selected walking speed (SSWS), 6-minute walk test, Fugl-Meyer motor assessment, Berg Balance Scale, and Dynamic Gait Index. Results. There were no significant differences between groups at baseline. Within-group comparisons revealed significant improvements in paretic and nonparetic knee extensor muscle power generation in both groups. Additionally, young participants significantly improved SSWS. Improvements in SSWS were more strongly associated with improvements in power generation on both sides in young versus older participants. Conclusions. Younger adults after stroke seem to preferentially benefit from POWER training, particularly when increasing gait speed is a rehabilitation goal. Future research should aim to further understand age-related differences in response to training to provide optimal treatments for all individuals following stroke. PMID:27493828

  3. The Effects of POWER Training in Young and Older Adults after Stroke

    PubMed Central

    Aaron, Stacey E.; Embry, Aaron E.; Cence, Brian; Morgan, Patrick; Gregory, Chris M.

    2016-01-01

    Background. Approximately 35,000 strokes occur annually in adults below the age of 40, and there is disappointingly little data describing their responses to rehabilitation. The purpose of this analysis was to determine the effects of Poststroke Optimization of Walking using Explosive Resistance (POWER) training in young (<40 years) and older (>60 years) adults and to describe relationships between training-induced improvements in muscular and locomotor function. Methods. Data was analyzed from 16 individuals with chronic stroke who participated in 24 sessions of POWER training. Outcomes included muscle power generation, self-selected walking speed (SSWS), 6-minute walk test, Fugl-Meyer motor assessment, Berg Balance Scale, and Dynamic Gait Index. Results. There were no significant differences between groups at baseline. Within-group comparisons revealed significant improvements in paretic and nonparetic knee extensor muscle power generation in both groups. Additionally, young participants significantly improved SSWS. Improvements in SSWS were more strongly associated with improvements in power generation on both sides in young versus older participants. Conclusions. Younger adults after stroke seem to preferentially benefit from POWER training, particularly when increasing gait speed is a rehabilitation goal. Future research should aim to further understand age-related differences in response to training to provide optimal treatments for all individuals following stroke. PMID:27493828

  4. [Evaluation of the agglutination test (AT), complement fixation test (CFT) and the antiglobulin test (AGT) in the diagnosis of swine brucellosis. III. Basic studies].

    PubMed

    Karpiński, T M; Zórawski, C; Skwarek, P

    1986-01-01

    In the examinations of the swine sera obtained from swines immunized s.c. with adjuvant Br.abortus S19 vaccine or Br.suis 1417 vaccine, it was found that agglutinins were present after 3 weeks, and C.F. antibodies or incomplete agglutinins normally after injections. Probably, in the first period of Brucella infection negative results of C.F.T. or AGT or both will be obtained. In the swine sera from Brucella free herds, agglutinins reacting with the Brucellognost antigen were present. The performance of mercaptoethanol test or C.F.T. lead in most cases to suitable diagnosis. In our conditions we have not obtained results which permit to classify AGT as a supplement test in serodiagnosis of swine brucellosis. PMID:3822855

  5. Power train analysis for the DOE/NASA 100-kW wind turbine generator

    NASA Technical Reports Server (NTRS)

    Seidel, R. C.; Gold, H.; Wenzel, L. M.

    1978-01-01

    Progress in explaining variations of power experienced in the on-line operation of a 100 kW experimental wind turbine-generator is reported. Data are presented that show the oscillations tend to be characteristic of a wind-driven synchronous generator because of low torsional damping in the power train, resonances of its large structure, and excitation by unsteady and nonuniform wind flow. The report includes dynamic analysis of the drive-train torsion, the generator, passive driveline damping, and active pitch control as well as correlation with experimental recordings. The analysis assumes one machine on an infinite bus with constant generator-field excitation.

  6. Simulation of three-dimensional multi-phase flow characteristics in the deswirl section of the CDIF MHD power train

    SciTech Connect

    Chang, S.L.; Lottes, S.A.; Petrick, M.

    1994-06-01

    A three-dimensional, two-phase, turbulent flow computer code was used to predict flow characteristics of seed particles and coal gas in the deswirl section of the CDIF MHD power train system. Seed material which has a great effect on the overall performance of the MHD system is injected in the deswirl against the swirling coal gas flow coming from the first stage combustor. While testing the MHD system, excessive seed material (70% more than theoretical value) was required to achieve design operating conditions. Calculations show that the swirling coal gas flow turns a 90 degree angle to minimize the swirl motion before entering a second stage combustor and many seed particles are too slow to react to the flow turning and deposit on the walls of the deswirl section. Some seed material deposited on the walls is covered by slag layer and removed from the gas flow. The reduction of seed material in the gas flow decreases MHD power generation significantly. A computational experiment was conducted and its results show that seed injection on the wall can be minimized by simply changing the seed injection and an optimum location was identified. If seed is injected from the location of choice, the seed deposition is reduced by a factor of 10 compared to the original case.

  7. Concurrent neuromechanical and functional gains following upper-extremity power training post-stroke

    PubMed Central

    2013-01-01

    Background Repetitive task practice is argued to drive neural plasticity following stroke. However, current evidence reveals that hemiparetic weakness impairs the capacity to perform, and practice, movements appropriately. Here we investigated how power training (i.e., high-intensity, dynamic resistance training) affects recovery of upper-extremity motor function post-stroke. We hypothesized that power training, as a component of upper-extremity rehabilitation, would promote greater functional gains than functional task practice without deleterious consequences. Method Nineteen chronic hemiparetic individuals were studied using a crossover design. All participants received both functional task practice (FTP) and HYBRID (combined FTP and power training) in random order. Blinded evaluations performed at baseline, following each intervention block and 6-months post-intervention included: Wolf Motor Function Test (WMFT-FAS, Primary Outcome), upper-extremity Fugl-Meyer Motor Assessment, Ashworth Scale, and Functional Independence Measure. Neuromechanical function was evaluated using isometric and dynamic joint torques and concurrent agonist EMG. Biceps stretch reflex responses were evaluated using passive elbow stretches ranging from 60 to 180º/s and determining: EMG onset position threshold, burst duration, burst intensity and passive torque at each speed. Results Primary outcome: Improvements in WMFT-FAS were significantly greater following HYBRID vs. FTP (p = .049), regardless of treatment order. These functional improvements were retained 6-months post-intervention (p = .03). Secondary outcomes: A greater proportion of participants achieved minimally important differences (MID) following HYBRID vs. FTP (p = .03). MIDs were retained 6-months post-intervention. Ashworth scores were unchanged (p > .05). Increased maximal isometric joint torque, agonist EMG and peak power were significantly greater following HYBRID vs. FTP (p < .05) and effects were

  8. A preliminary study of solar powdered aircraft and associated power trains

    NASA Technical Reports Server (NTRS)

    Hall, D. W.; Fortenbach, C. D.; Dimiceli, E. V.; Parks, R. W.

    1983-01-01

    The feasibility of regeneratively powered solar high altitude powered platform (HAPP) remotely piloted vehicles was assessed. Those technologies which must be pursued to make long duration solar HAPPs feasible are recommended. A methodology which involved characterization and parametric analysis of roughly two dozen variables to determine vehicles capable of fulfilling the primary mission are defined. One of these vehicles was then conceptually designed. Variations of each major design parameter were investigated along with state-of-the-art changes in power train component capabilities. The midlatitude mission studied would be attainable by a solar HAPP if fuel cell, electrolyzer and photovoltaic technologies are pursued. Vehicles will be very large and have very lightweight structures in order to attain the combinations of altitude and duration required by the primary mission.

  9. Nuclear Expression of Renin-Angiotensin System Components in NRK-52E Renal Epithelial Cells

    PubMed Central

    Alzayadneh, Ebaa M.; Chappell, Mark C.

    2014-01-01

    Introduction Isolated nuclei of sheep proximal tubules express angiotensin receptors as well as angiotensinogen (AGT) and renin. The present study characterized the NRK-52E tubular epithelial cell line for the intracellular expression of renin-angiotensin system (RAS) components. Methods RAS components were visualized by immunofluorescent staining in intact cells and protein expression in isolate nuclei. Results An antibody to the Ang I sequence of AGT (AI-AGT) revealed only cytosolic staining, while an antibody to an internal epitope of AGT (Int-AGT) revealed primarily nuclear staining. Immunoblots of nuclear and cytosolic fractions confirmed the differential cell staining of AGT. Immunostaining for renin was present on nuclei of intact cells. Nuclear renin activity averaged 0.77 ± 0.05 nmol/mg protein/hr that was reduced by aliskiren (0.13 ± 0.01 nmol/mg/hr, n=3, p<0.01); trypsin activation increased activity 3-fold. Peptide staining localized Ang II and Ang-(1–7) to the nucleus and peptide content averaged 59 ± 2 and 57 ± 22 fmol/mg (n=4), respectively. Peptide metabolism in isolated nuclei revealed the processing of Ang I to Ang-(1–7) by thimet oligopeptidase. Conclusion We conclude that the NRK-52E cells express an intracellular RAS localized to the nucleus and may be an appropriate cell model to elucidate the functional relevance of this system. PMID:24961503

  10. Effects of Two Instructional Techniques Used with the Ford Power Train Simulator on the Performance of Mississippi Vocational Agriculture Students.

    ERIC Educational Resources Information Center

    Perritt, Roger Dale; Shinn, Glen C.

    A Mississippi study examined the effects of two instructional techniques using the Ford power train unit as an instructional aid. Eight schools were randomly selected from a population of 33 vocational agricultural departments. Three schools with 10 students from each school were randomly selected and assigned to treatment A, traditional…

  11. 76 FR 27366 - Chrysler Group, LLC, Power Train Division, Mack Avenue Engine Plants #1 And #2, Including On-Site...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-05-11

    ... notice was published in the Federal Register on April 22, 2011 (76 FR 22731). The notice was amended on..., 2011 (76 FR 22729). At the request of a company official, the Department reviewed the certification for... Employment and Training Administration Chrysler Group, LLC, Power Train Division, Mack Avenue Engine Plants...

  12. Lower extremity muscle function after strength or power training in older adults.

    PubMed

    Marsh, Anthony P; Miller, Michael E; Rejeski, W Jack; Hutton, Stacy L; Kritchevsky, Stephen B

    2009-10-01

    It is unclear whether strength training (ST) or power training (PT) is the more effective intervention at improving muscle strength and power and physical function in older adults. The authors compared the effects of lower extremity PT with those of ST on muscle strength and power in 45 older adults (74.8 +/- 5.7 yr) with self-reported difficulty in common daily activities. Participants were randomized to 1 of 3 treatment groups: PT, ST, or wait-list control. PT and ST trained 3 times/wk for 12 wk using knee-extension (KE) and leg-press (LP) machines at approximately 70% of 1-repetition maximum (1RM). For PT, the concentric phase of the KE and LP was completed "as fast as possible," whereas for ST the concentric phase was 2-3 s. Both PT and ST paused briefly at the midpoint of the movement and completed the eccentric phase of the movement in 2-3 s. PT and ST groups showed significant improvements in KE and LP 1RM compared with the control group. Maximum KE and LP power increased approximately twofold in PT compared with ST. At 12 wk, compared with control, maximum KE and LP power were significantly increased for the PT group but not for the ST group. In older adults with compromised function, PT leads to similar increases in strength and larger increases in power than ST. PMID:19940322

  13. Comparison of Parallel and Series Hybrid Power Trains for Transit Bus Applications

    DOE PAGESBeta

    Gao, Zhiming; Daw, C. Stuart; Smith, David E.; LaClair, Tim J.; Parks, James E.; Jones, Perry T.

    2016-08-01

    The fuel economy and emissions of conventional and hybrid buses equipped with emissions after treatment were evaluated via computational simulation for six representative city bus drive cycles. Both series and parallel configurations for the hybrid case were studied. The simulation results indicated that series hybrid buses have the greatest overall advantage in fuel economy. The series and parallel hybrid buses were predicted to produce similar carbon monoxide and hydrocarbon tailpipe emissions but were also predicted to have reduced tailpipe emissions of nitrogen oxides compared with the conventional bus in higher speed cycles. For the New York bus cycle, which hasmore » the lowest average speed among the cycles evaluated, the series bus tailpipe emissions were somewhat higher than they were for the conventional bus; the parallel hybrid bus had significantly lower tailpipe emissions. All three bus power trains were found to require periodic active diesel particulate filter regeneration to maintain control of particulate matter. Finally, plug-in operation of series hybrid buses appears to offer significant fuel economy benefits and is easily employed because of the relatively large battery capacity that is typical of the series hybrid configuration.« less

  14. Near-term hybrid vehicle program, phase 1. Appendix B: Design trade-off studies. [various hybrid/electric power train configurations and electrical and mechanical drive-line components

    NASA Technical Reports Server (NTRS)

    1979-01-01

    The relative attractiveness of various hybrid/electric power train configurations and electrical and mechanical drive-line components was studied. The initial screening was concerned primarily with total vehicle weight and economic factors and identified the hybrid power train combinations which warranted detailed evaluation over various driving cycles. This was done using a second-by-second vehicle simulation program which permitted the calculations of fuel economy, electricity usage, and emissions as a function of distance traveled in urban and highway driving. Power train arrangement possibilities were examined in terms of their effect on vehicle handling, safety, serviceability, and passenger comfort. A dc electric drive system utilizing a separately excited motor with field control and battery switching was selected for the near term hybrid vehicle. Hybrid vehicle simulations showed that for the first 30 mi (the electric range of the vehicle) in urban driving, the fuel economy was 80 mpg using a gasoline engine and 100 mpg using a diesel engine. In urban driving the hybrid would save about 75% of the fuel used by the conventional vehicle and in combined urban/highway driving the fuel saving is about 50%.

  15. Advanced Gas Turbine (AGT)

    NASA Technical Reports Server (NTRS)

    1983-01-01

    The development and progress of the Advanced Gas Turbine engine program is examined. An analysis of the role of ceramics in the design and major engine components is included. Projected fuel economy, emissions and performance standards, and versatility in fuel use are also discussed.

  16. Crossfit-based high-intensity power training improves maximal aerobic fitness and body composition.

    PubMed

    Smith, Michael M; Sommer, Allan J; Starkoff, Brooke E; Devor, Steven T

    2013-11-01

    The purpose of this study was to examine the effects of a crossfit-based high-intensity power training (HIPT) program on aerobic fitness and body composition. Healthy subjects of both genders (23 men, 20 women) spanning all levels of aerobic fitness and body composition completed 10 weeks of HIPT consisting of lifts such as the squat, deadlift, clean, snatch, and overhead press performed as quickly as possible. Additionally, this crossfit-based HIPT program included skill work for the improvement of traditional Olympic lifts and selected gymnastic exercises. Body fat percentage was estimated using whole-body plethysmography, and maximal aerobic capacity (VO2max) was measured by analyzing expired gasses during a Bruce protocol maximal graded treadmill test. These variables were measured again after 10 weeks of training and compared for significant changes using a paired t-test. Results showed significant (p < 0.05) improvements of VO2max in men (43.10 ± 1.40 to 48.96 ± 1.42 ml · kg · min) and women (35.98 ± 1.60 to 40.22 ± 1.62 ml · kg · min) and decreased body fat percentage in men (22.2 ± 1.3 to 18.0 ± 1.3) and women (26.6 ± 2.0 to 23.2 ± 2.0). These improvements were significant across all levels of initial fitness. Significant correlations between absolute oxygen consumption and oxygen consumption relative to body weight was found in both men (r = 0.83, p < 0.001) and women (r = 0.94, p < 0.001), indicating that HIPT improved VO2max scaled to body weight independent of changes to body composition. Our data show that HIPT significantly improves VO2max and body composition in subjects of both genders across all levels of fitness. PMID:23439334

  17. Role of Muscle Morphology in Jumping, Sprinting, and Throwing Performance in Participants With Different Power Training Duration Experience.

    PubMed

    Methenitis, Spyridon K; Zaras, Nikolaos D; Spengos, Konstantinos M; Stasinaki, Angeliki-Nikoletta E; Karampatsos, Giorgos P; Georgiadis, Giorgos V; Terzis, Gerasimos D

    2016-03-01

    The aim of the study was to examine the correlation between muscle morphology and jumping, sprinting, and throwing performance in participants with different power training duration experience. Thirty-six power-trained young men were assigned to 3 groups according to the length of their power training: less experienced (<1 year), moderately experienced (1-3 years), and experienced (4-7 years). All participants performed countermovement and squat jumps, 60-m sprint, and shot throws twice. Lean body mass (LBM) was evaluated with dual-energy x-ray absorptiometry and thigh muscle cross-sectional area (CSA) with anthropometry. The vastus lateralis architecture and fiber type composition were evaluated with ultrasonography and muscle biopsies, respectively. When all subjects were considered as 1 group (n = 36), jumping performance was correlated with LBM, fascicle length, and type II fiber CSA; sprinting performance was correlated with estimated thigh muscle CSA alone; and shot throwing was correlated with LBM and type I, IIA fiber CSA. In the least experienced group, the LBM of the lower extremities was the most significant contributor for power performance, whereas in the moderately experienced group, the LBM, architectural properties, and type II fiber percentage CSA were the most significant contributors. For the experienced group, fascicle length and type II fiber percentage CSA were the most significant factors for power performance. These data suggest that jumping performance is linked with muscle morphology, regardless of strength or power training. The vastus lateralis muscle morphology could only partially explain throwing performance, whereas it cannot predict sprinting performance. Power performance in experienced participants rely more on the quality of the muscle tissue rather than the quantity. PMID:26907845

  18. Effects of high-speed power training on muscle strength and power in patients with multiple sclerosis.

    PubMed

    Medina-Perez, Carlos; de Souza-Teixeira, Fernanda; Fernandez-Gonzalo, Rodrigo; Hernandez-Murua, Jose-Aldo; Antonio de Paz-Fernandez, Jose

    2016-01-01

    This study examined the effects of a high-speed power training program in peak muscle power and maximal voluntary isometric contraction (MVIC) of knee extensors in patients with relapsing-remitting multiple sclerosis (MS). Forty patients, 20 women (age 42.8 +/- 10.3 yr) and 20 men (age 44.0 +/- 8.7 yr) diagnosed with relapsing-remitting MS were randomly assigned, with respect to sex, to either an exercise group or a control group. Participants from the exercise group performed 12 wk of supervised muscle power training of knee extensors. All subjects were tested for MVIC and peak muscle power at baseline and after the training intervention. A strain gauge was used to measure the MVIC, and peak muscle power was assessed with a linear encoder at five relative loads. The training-related effects were assessed using a t-test. The results showed no significant changes in the control group from baseline to postintervention evaluation. In contrast, the exercise group significantly increased MVIC (10.8%; p < 0.05) and muscle power at 40, 50, 60, 70, and 80% of the MVIC by 21.8, 14.5, 17.3, 19.4, and 22.3%, respectively (p < 0.01), after the training. These findings suggest that 12 wk of high-speed power training improve both MVIC and muscle power at five different loads in patients with relapsing-remitting MS. PMID:27270470

  19. Effect of traditional resistance and power training using rated perceived exertion for enhancement of muscle strength, power, and functional performance.

    PubMed

    Tiggemann, Carlos Leandro; Dias, Caroline Pieta; Radaelli, Regis; Massa, Jéssica Cassales; Bortoluzzi, Rafael; Schoenell, Maira Cristina Wolf; Noll, Matias; Alberton, Cristine Lima; Kruel, Luiz Fernando Martins

    2016-04-01

    The present study compared the effects of 12 weeks of traditional resistance training and power training using rated perceived exertion (RPE) to determine training intensity on improvements in strength, muscle power, and ability to perform functional task in older women. Thirty healthy elderly women (60-75 years) were randomly assigned to traditional resistance training group (TRT; n = 15) or power training group (PT; n = 15). Participants trained twice a week for 12 weeks using six exercises. The training protocol was designed to ascertain that participants exercised at an RPE of 13-18 (on a 6-20 scale). Maximal dynamic strength, muscle power, and functional performance of lower limb muscles were assessed. Maximal dynamic strength muscle strength leg press (≈58 %) and knee extension (≈20 %) increased significantly (p < 0.001) and similarly in both groups after training. Muscle power also increased with training (≈27 %; p < 0.05), with no difference between groups. Both groups also improved their functional performance after training period (≈13 %; p < 0.001), with no difference between groups. The present study showed that TRT and PT using RPE scale to control intensity were significantly and similarly effective in improving maximal strength, muscle power, and functional performance of lower limbs in elderly women. PMID:27009295

  20. Renin–angiotensin system gene polymorphisms and endometrial cancer

    PubMed Central

    Delforce, Sarah J; Wang, Yu; Ashton, Katie A; Proietto, Anthony; Otton, Geoffrey; Blackwell, C Caroline; Scott, Rodney J; Lumbers, Eugenie R

    2016-01-01

    Endometrial cancer (EC) is the most common gynaecological malignancy and its incidence is increasing. Dysregulation of the endometrial renin–angiotensin system (RAS) could predispose to EC; therefore, we studied the prevalence of RAS single nucleotide polymorphisms (SNPs) in Australian women with EC. SNPs assessed were AGT M235T (rs699); AGTR1 A1166C (rs5186); ACE A240T and T93C (rs4291, rs4292) and ATP6AP2 (rs2968915). They were identified using TaqMan SNP Genotyping Assays. The C allele of the AGTR1 SNP (rs5186) was more prevalent in women with EC (odds ratio (OR) 1.7, 95% confidence interval (CI) (1.2–2.3), P=0.002). The CC genotype of this SNP is associated with upregulation of the angiotensin II type 1 receptor (AGTR1). The G allele of AGT rs699, which is associated with higher angiotensinogen (AGT) levels, was less prevalent in women with EC (OR 0.54, 95% CI (0.39–0.74), P<0.001) compared with controls. AGT and AGT formed by removal of angiotensin I (des(Ang I)AGT) are both anti-angiogenic. In women with EC who had had hormone replacement therapy (HRT), the prevalence of the AGTR1 SNP (rs5186) and the ACE SNPs (rs4291 and rs4292) was greater than in women who had no record of HRT; SNP rs4291 is associated with increased plasma ACE activity. These data suggest there is an interaction between genotype, oestrogen replacement therapy and EC. In conclusion, the prevalence of two SNPs that enhance RAS activity was different in women with EC compared with healthy controls. These genetic factors may interact with obesity and hyperoestrogenism, predisposing ageing, obese women to EC. PMID:27068935

  1. Renin-angiotensin system gene polymorphisms and endometrial cancer.

    PubMed

    Pringle, Kirsty G; Delforce, Sarah J; Wang, Yu; Ashton, Katie A; Proietto, Anthony; Otton, Geoffrey; Blackwell, C Caroline; Scott, Rodney J; Lumbers, Eugenie R

    2016-05-01

    Endometrial cancer (EC) is the most common gynaecological malignancy and its incidence is increasing. Dysregulation of the endometrial renin-angiotensin system (RAS) could predispose to EC; therefore, we studied the prevalence of RAS single nucleotide polymorphisms (SNPs) in Australian women with EC. SNPs assessed were AGT M235T (rs699); AGTR1 A1166C (rs5186); ACE A240T and T93C (rs4291, rs4292) and ATP6AP2 (rs2968915). They were identified using TaqMan SNP Genotyping Assays. The C allele of the AGTR1 SNP (rs5186) was more prevalent in women with EC (odds ratio (OR) 1.7, 95% confidence interval (CI) (1.2-2.3), P=0.002). The CC genotype of this SNP is associated with upregulation of the angiotensin II type 1 receptor (AGTR1). The G allele of AGT rs699, which is associated with higher angiotensinogen (AGT) levels, was less prevalent in women with EC (OR 0.54, 95% CI (0.39-0.74), P<0.001) compared with controls. AGT and AGT formed by removal of angiotensin I (des(Ang I)AGT) are both anti-angiogenic. In women with EC who had had hormone replacement therapy (HRT), the prevalence of the AGTR1 SNP (rs5186) and the ACE SNPs (rs4291 and rs4292) was greater than in women who had no record of HRT; SNP rs4291 is associated with increased plasma ACE activity. These data suggest there is an interaction between genotype, oestrogen replacement therapy and EC. In conclusion, the prevalence of two SNPs that enhance RAS activity was different in women with EC compared with healthy controls. These genetic factors may interact with obesity and hyperoestrogenism, predisposing ageing, obese women to EC. PMID:27068935

  2. High-speed power training in older adults: A shift of the external resistance at which peak power is produced

    PubMed Central

    Sayers, Stephen P.; Gibson, Kyle

    2013-01-01

    Studies have shown that power training increases peak power in older adults. Evaluating the external resistance (% one repetition-maximum [1RM]) at which peak power is developed is critical given that changes in the components of peak power (force and velocity) are dependent on the %1RM at which peak power occurs. The purpose of this study was to compare the changes in peak power (and the external resistance at which peak power occurred) after 12 weeks of high-speed power training versus traditional slow-speed strength training. Seventy-two older men and women were randomized to high-speed power training at 40% of the one-repetition maximum (1RM) (HSPT: n=24 [70.8±6.8 yrs]); traditional RT at 80% 1RM (STR: n=22 [68.6±7.8 yrs]); or control (CON: n=18 [71.5±6.1 yrs]). Measures of muscle performance were obtained at baseline and after the 12-week training intervention. Changes in muscle power and 1RM strength improved similarly with both HSPT and SSST, but HSPT shifted the external resistance at which peak power was produced to a lower external resistance (from 67%1RM to 52%1RM) compared to SSST (from 65%1RM to 62%1RM)(p<0.05), thus increasing the velocity component of peak power (change: HSPT=0.18±0.21m/s; SSST=−0.03±0.15 m/s)(p<0.05). Because sufficient speed of the lower limb is necessary for functional tasks related to safety (crossing a busy intersection, fall prevention), HSPT should be implemented in older adults to improve power at lower external resistances, thus increasing the velocity component of power and making older adults safer in their environment. These data provide clinicians with the necessary information to tailor exercise programs to the individual needs of the older adult, affecting the components of power. PMID:23897022

  3. 36 CFR 1192.173 - Automated guideway transit vehicles and systems.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 36 Parks, Forests, and Public Property 3 2011-07-01 2011-07-01 false Automated guideway transit... TRANSPORTATION VEHICLES Other Vehicles and Systems § 1192.173 Automated guideway transit vehicles and systems. (a) Automated Guideway Transit (AGT) vehicles and systems, sometimes called “people movers”, operated...

  4. 36 CFR 1192.173 - Automated guideway transit vehicles and systems.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 36 Parks, Forests, and Public Property 3 2014-07-01 2014-07-01 false Automated guideway transit... TRANSPORTATION VEHICLES Other Vehicles and Systems § 1192.173 Automated guideway transit vehicles and systems. (a) Automated Guideway Transit (AGT) vehicles and systems, sometimes called “people movers”, operated...

  5. 36 CFR 1192.173 - Automated guideway transit vehicles and systems.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Automated guideway transit... TRANSPORTATION VEHICLES Other Vehicles and Systems § 1192.173 Automated guideway transit vehicles and systems. (a) Automated Guideway Transit (AGT) vehicles and systems, sometimes called “people movers”, operated...

  6. 36 CFR 1192.173 - Automated guideway transit vehicles and systems.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 36 Parks, Forests, and Public Property 3 2013-07-01 2012-07-01 true Automated guideway transit... TRANSPORTATION VEHICLES Other Vehicles and Systems § 1192.173 Automated guideway transit vehicles and systems. (a) Automated Guideway Transit (AGT) vehicles and systems, sometimes called “people movers”, operated...

  7. 36 CFR 1192.173 - Automated guideway transit vehicles and systems.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 36 Parks, Forests, and Public Property 3 2012-07-01 2012-07-01 false Automated guideway transit... TRANSPORTATION VEHICLES Other Vehicles and Systems § 1192.173 Automated guideway transit vehicles and systems. (a) Automated Guideway Transit (AGT) vehicles and systems, sometimes called “people movers”, operated...

  8. 49 CFR 38.173 - Automated guideway transit vehicles and systems.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 1 2012-10-01 2012-10-01 false Automated guideway transit vehicles and systems. 38.173 Section 38.173 Transportation Office of the Secretary of Transportation AMERICANS WITH....173 Automated guideway transit vehicles and systems. (a) Automated Guideway Transit (AGT) vehicles...

  9. 49 CFR 38.173 - Automated guideway transit vehicles and systems.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 1 2014-10-01 2014-10-01 false Automated guideway transit vehicles and systems. 38.173 Section 38.173 Transportation Office of the Secretary of Transportation AMERICANS WITH....173 Automated guideway transit vehicles and systems. (a) Automated Guideway Transit (AGT) vehicles...

  10. 49 CFR 38.173 - Automated guideway transit vehicles and systems.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 1 2013-10-01 2013-10-01 false Automated guideway transit vehicles and systems. 38.173 Section 38.173 Transportation Office of the Secretary of Transportation AMERICANS WITH....173 Automated guideway transit vehicles and systems. (a) Automated Guideway Transit (AGT) vehicles...

  11. 49 CFR 38.173 - Automated guideway transit vehicles and systems.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 1 2010-10-01 2010-10-01 false Automated guideway transit vehicles and systems. 38.173 Section 38.173 Transportation Office of the Secretary of Transportation AMERICANS WITH....173 Automated guideway transit vehicles and systems. (a) Automated Guideway Transit (AGT) vehicles...

  12. 49 CFR 38.173 - Automated guideway transit vehicles and systems.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 1 2011-10-01 2011-10-01 false Automated guideway transit vehicles and systems. 38.173 Section 38.173 Transportation Office of the Secretary of Transportation AMERICANS WITH....173 Automated guideway transit vehicles and systems. (a) Automated Guideway Transit (AGT) vehicles...

  13. Hybrid Electric Power Train and Control Strategies Automotive Technology Education (GATE) Program

    SciTech Connect

    Andrew Frank

    2006-05-31

    Plug-in hybrid electric vehicles (PHEV) offer societal benefits through their ability to displace the use of petroleum fuels. Petroleum fuels represent a polluting and politically destabilizing energy carrier. PHEV technologies can move transportation away from petroleum fuel sources by enabling domestically generated electricity and liquids bio-fuels to serve as a carrier for transportation energy. Additionally, the All-Electric-Range (AER) offered by PHEVs can significantly reduce demand for expensive and polluting liquid fuels. The GATE funding received during the 1998 through 2004 funding cycle by the UC Davis Hybrid Electric Vehicle Center (HEVC) was used to advance and train researchers in PHEV technologies. GATE funding was used to construct a rigorous PHEV curriculum, provide financial support for HEVC researchers, and provide material support for research efforts. A rigorous curriculum was developed through the UC Davis Mechanical and Aeronautical Engineering Department to train HEVC researchers. Students' research benefited from this course work by advancing the graduate student researchers' understanding of key PHEV design considerations. GATE support assisted HEVC researchers in authoring technical articles and producing patents. By supporting HEVC researchers multiple Master's theses were written as well as journal articles and publications. The topics from these publications include Continuously Variable Transmission control strategies and PHEV cross platform controls software development. The GATE funding has been well used to advance PHEV systems. The UC Davis Hybrid Electric Vehicle Center is greatly appreciative for the opportunities GATE funding provided. The goals and objectives for the HEVC GATE funding were to nourish engineering research in PHEV technologies. The funding supplied equipment needed to allow researchers to investigate PHEV design sensitivities and to further optimize system components. Over a dozen PHEV researchers benefited

  14. AGT M235t polymorphism and heart failure in a cohort of Tunisian population: diagnostic and prognostic value

    PubMed Central

    Imen, Trabelsi; Grissa, Mohamed Habib; Boubaker, Hamdi; Beltaief, Kaouther; Messous, Salma; Tounsi, Nejia; Slimani, Afef; khouloud, chehaibi; Bouida, Wahid; Boukef, Riadh; Slimene, Mohammed Naceur; Nouira, Semir

    2015-01-01

    Activity of the renin-angiotensin Aldosterone system is increased in patients with heart failure (HF). The Angiotensinogen gene and specifically M235T polymorphism has been linked to susceptibility to hypertension, coronary heart disease and atrial fibrillation. Its role in heart failure is not yet sufficiently demonstrated. The aim of the present study was to assess the association between rs699 (M235T) polymorphism and heart failure in terms of diagnosis and prognosis. We included all patients over 20 years old consulting in the Emergency Department for acute dyspnea. According to the results of the B-type natriuretic peptide (BNP level), patients were divided into two groups: HF and non-HF group. DNA study was performed for all subjects and their genotypes were identified as TT, CT or CC. Mortality was followed for one year. We included 234 patients. We found the diagnosis of HF in 73 patients out of 160 (45%). Our results showed that the frequency of the T allele was higher in HF group patients than in non-HF group (69% vs. 33%, P<0.01). Patients carrying the TT and CT genotypes had a higher proportion of HF than those carrying the CC genotype (respectively 53% and 31% vs. 15%, P<0.01). According to multivariate analysis, TT genotype presented the highest risk of HF (OR=4.9 95% CI: 2.12-9.1) and the highest risk of death (OR=6.45 95% CI: 3.6-16.4) compared to the other two genotypes. The current study suggests that M235T polymorphism might be associated with increased risk of both HF and death. PMID:26629155

  15. Compact Hybrid Automotive Propulsion System

    NASA Technical Reports Server (NTRS)

    Lupo, G.

    1986-01-01

    Power train proposed for experimental vehicle powered by internal combustion engine and electric motor. Intended for front-wheel drive automobile, power train mass produced using existing technology. System includes internal-combustion engine, electric motor, continuously variable transmission, torque converter, differential, and control and adjustment systems for electric motor and transmission. Continuously variable transmission integrated into hydraulic system that also handles power steering and power brakes. Batteries for electric motor mounted elsewhere in vehicle.

  16. Power training and postmenopausal hormone therapy affect transcriptional control of specific co-regulated gene clusters in skeletal muscle

    PubMed Central

    Fey, Vidal; Törmäkangas, Timo; Ronkainen, Paula H. A.; Taaffe, Dennis R.; Takala, Timo; Koskinen, Satu; Cheng, Sulin; Puolakka, Jukka; Kujala, Urho M.; Suominen, Harri; Sipilä, Sarianna; Kovanen, Vuokko

    2010-01-01

    At the moment, there is no clear molecular explanation for the steeper decline in muscle performance after menopause or the mechanisms of counteractive treatments. The goal of this genome-wide study was to identify the genes and gene clusters through which power training (PT) comprising jumping activities or estrogen containing hormone replacement therapy (HRT) may affect skeletal muscle properties after menopause. We used musculus vastus lateralis samples from early stage postmenopausal (50–57 years old) women participating in a yearlong randomized double-blind placebo-controlled trial with PT and HRT interventions. Using microarray platform with over 24,000 probes, we identified 665 differentially expressed genes. The hierarchical clustering method was used to assort the genes. Additionally, enrichment analysis of gene ontology (GO) terms and Kyoto Encyclopedia of Genes and Genomes (KEGG) pathways was carried out to clarify whether assorted gene clusters are enriched with particular functional categories. The analysis revealed transcriptional regulation of 49 GO/KEGG categories. PT upregulated transcription in “response to contraction”—category revealing novel candidate genes for contraction-related regulation of muscle function while HRT upregulated gene expression related to functionality of mitochondria. Moreover, several functional categories tightly related to muscle energy metabolism, development, and function were affected regardless of the treatment. Our results emphasize that during the early stages of the postmenopause, muscle properties are under transcriptional modulation, which both PT and HRT partially counteract leading to preservation of muscle power and potentially reducing the risk for aging-related muscle weakness. More specifically, PT and HRT may function through improving energy metabolism, response to contraction as well as by preserving functionality of the mitochondria. Electronic supplementary material The online version of this

  17. Exts and the AGT Relations

    NASA Astrophysics Data System (ADS)

    Neguţ, Andrei

    2016-06-01

    We prove the connection between the Nekrasov partition function of {{N}=2} super-symmetric U(2) gauge theory with adjoint matter and conformal blocks for the Virasoro algebra, as predicted by the Alday-Gaiotto-Tachikawa relations. Mathematically, this is achieved by relating the Carlsson-Okounkov Ext vector bundle on the moduli space of rank 2 sheaves with Liouville vertex operators. Our approach is geometric in nature, and uses a new method for intersection-theoretic computations of the Ext operator.

  18. Exts and the AGT Relations

    NASA Astrophysics Data System (ADS)

    Neguţ, Andrei

    2016-09-01

    We prove the connection between the Nekrasov partition function of {N=2} super-symmetric U(2) gauge theory with adjoint matter and conformal blocks for the Virasoro algebra, as predicted by the Alday-Gaiotto-Tachikawa relations. Mathematically, this is achieved by relating the Carlsson-Okounkov Ext vector bundle on the moduli space of rank 2 sheaves with Liouville vertex operators. Our approach is geometric in nature, and uses a new method for intersection-theoretic computations of the Ext operator.

  19. AGT-102 automotive gas turbine

    NASA Technical Reports Server (NTRS)

    1981-01-01

    Development of a gas turbine powertrain with a 30% fuel economy improvement over a comparable S1 reciprocating engine, operation within 0.41 HC, 3.4 CO, and 0.40 NOx grams per mile emissions levels, and ability to use a variety of alternate fuels is summarized. The powertrain concept consists of a single-shaft engine with a ceramic inner shell for containment of hot gasses and support of twin regenerators. It uses a fixed-geometry, lean, premixed, prevaporized combustor, and a ceramic radial turbine rotor supported by an air-lubricated journal bearing. The engine is coupled to the vehicle through a widerange continuously variable transmission, which utilizes gearing and a variable-ratio metal compression belt. A response assist flywheel is used to achieve acceptable levels of engine response. The package offers a 100 lb weight advantage in a Chrysler K Car front-wheel-drive installation. Initial layout studies, preliminary transient thermal analysis, ceramic inner housing structural analysis, and detailed performance analysis were carried out for the basic engine.

  20. Urinary Angiotensinogen as a Potential Biomarker of Intrarenal Renin-angiotensin System Activity in Chinese Patients with Chronic Kidney Disease.

    PubMed

    Xu, Z; Xu, B; Xu, C

    2014-09-01

    Urinary angiotensinogen (AGT) mainly derives from the AGT produced in the proximal tubular cells. Evidence exists that supports the correlation between urinary AGT and circulating AGT. Previous studies measured urinary AGT by radioimmunoassay which is not convenient for clinical practice. In this study, we utilized an enzyme-linked immunosorbent assay (ELISA) based method to quantify urinary AGT. We analysed the relationship between urinary AGT and intrarenal angiotensin II (Ang II) activity in patients with chronic kidney disease (CKD). Urinary and plasma renin activity, AGT, Ang II and aldosterone were measured by radioimmunoassay or ELISA in 128 CKD patients. Furthermore, expression levels of intrarenal renin, AGT, Ang II and Ang II receptor were examined by immunohistochemistry staining (IHCS) in 72 CKD patients undergoing renal biopsy. Average urinary AGT was 2.02 ± 0.55 ng/(mg Cr). Hypertension, urinary protein, urinary Ang II and urinary Type IV collagen (Col IV) positively correlated with urinary AGT. Estimated glomerular filtration rate (eGFR), urinary sodium and serum AGT negatively correlated with urinary AGT. Multiple regression analysis indicated that low serum AGT, high urinary protein, urinary Ang II and urinary Col IV correlated significantly with high urinary AGT. Moreover, we observed positive correlation between urinary AGT and positive IHCS area of AGT, Ang II and Ang II Type 1 receptor inrenal tissue. These data suggest that urinary AGT might be a potential biomarker of intrarenal angiotensin II activity in CKD patients. PMID:25781279

  1. Urinary Angiotensinogen as a Potential Biomarker of Intrarenal Renin-angiotensin System Activity in Chinese Patients with Chronic Kidney Disease

    PubMed Central

    Xu, Z; Xu, B; Xu, C

    2014-01-01

    ABSTRACT Urinary angiotensinogen (AGT) mainly derives from the AGT produced in the proximal tubular cells. Evidence exists that support the correlation between urinary AGT and circulating AGT. Previous studies measured urinary AGT by radioimmunoassay which is not convenient for clinical practice. In this study, we utilized an enzyme-linked immunosorbent assay (ELISA) based method to quantify urinary AGT. We analysed the relationship between urinary AGT and intrarenal angiotensin II (Ang II) activity in patients with chronic kidney disease (CKD). Urinary and plasma renin activity, AGT, Ang II and aldosterone were measured by radioimmunoassay or ELISA in 128 CKD patients. Furthermore, expression levels of intrarenal renin, AGT, Ang II and Ang II receptor were examined by immunohistochemistry staining (IHCS) in 72 CKD patients undergoing renal biopsy. Average urinary AGT was 2.02 ± 0.55 ng/(mg Cr). Hypertension, urinary protein, urinary Ang II and urinary Type IV collagen (Col IV) positively correlated with urinary AGT. Estimated glomerular filtration rate (eGFR), urinary sodium and serum AGT negatively correlated with urinary AGT. Multiple regression analysis indicated that low serum AGT, high urinary protein, urinary Ang II and urinary Col IV correlated significantly with high urinary AGT. Moreover, we observed positive correlation between urinary AGT and positive IHCS area of AGT, Ang II and Ang II Type 1 receptor in renal tissue. These data suggest that urinary AGT might be a potential biomarker of intrarenal angiotensin II activity in CKD patients. PMID:25781279

  2. Renin-Angiotensin System Gene Variants and Type 2 Diabetes Mellitus: Influence of Angiotensinogen

    PubMed Central

    Joyce-Tan, Siew Mei; Zain, Shamsul Mohd; Abdul Sattar, Munavvar Zubaid; Abdullah, Nor Azizan

    2016-01-01

    Genome-wide association studies (GWAS) have been successfully used to call for variants associated with diseases including type 2 diabetes mellitus (T2DM). However, some variants are not included in the GWAS to avoid penalty in multiple hypothetic testing. Thus, candidate gene approach is still useful even at GWAS era. This study attempted to assess whether genetic variations in the renin-angiotensin system (RAS) and their gene interactions are associated with T2DM risk. We genotyped 290 T2DM patients and 267 controls using three genes of the RAS, namely, angiotensin converting enzyme (ACE), angiotensinogen (AGT), and angiotensin II type 1 receptor (AGTR1). There were significant differences in allele frequencies between cases and controls for AGT variants (P = 0.05) but not for ACE and AGTR1. Haplotype TCG of the AGT was associated with increased risk of T2DM (OR 1.92, 95% CI 1.15–3.20, permuted P = 0.012); however, no evidence of significant gene-gene interactions was seen. Nonetheless, our analysis revealed that the associations of the AGT variants with T2DM were independently associated. Thus, this study suggests that genetic variants of the RAS can modestly influence the T2DM risk. PMID:26682227

  3. Voluntary muscle activation improves with power training and is associated with changes in gait speed in mobility-limited older adults - A randomized controlled trial.

    PubMed

    Hvid, Lars G; Strotmeyer, Elsa S; Skjødt, Mathias; Magnussen, Line V; Andersen, Marianne; Caserotti, Paolo

    2016-07-01

    Incomplete voluntary muscle activation may contribute to impaired muscle mechanical function and physical function in older adults. Exercise interventions have been shown to increase voluntary muscle activation, although the evidence is sparse for mobility-limited older adults, particularly in association with physical function. This study examined the effects of 12weeks of power training on outcomes of voluntary muscle activation and gait speed in mobility-limited older adults from the Healthy Ageing Network of Competence (HANC) study. We included 37 older men and women with a usual gait speed of <0.9m/s in the per-protocol analysis: n=16 in the training group (TG: 12weeks of progressive high-load power training, 2 sessions per week; age: 82.3±1.3years, 56% women) and n=21 in the control group (CG: no interventions; age: 81.6±1.1years, 67% women). Knee extensor muscle thickness (ultrasonography), strength (isokinetic dynamometry), voluntary activation (interpolated twitch technique), and gait speed (2-min maximal walking test) were assessed at baseline and post-intervention. At baseline, TG and CG were comparable for all measures. Post-intervention, significant between-group changes (TG vs. CG; p<0.05) were observed for voluntary muscle activation (+6.2%), muscle strength (+13.4Nm), and gait speed (+0.12m/s), whereas the between-group change in muscle thickness was non-significant (+0.08cm). Improvements in voluntary muscle activation were associated with improvements in gait speed in TG (r=0.67, p<0.05). Importantly, voluntary muscle activation is improved in mobility-limited older adults following 12-weeks of progressive power training, and is associated with improved maximal gait speed. Incomplete voluntary muscle activation should be considered one of the key mechanisms influencing muscle mechanical function and gait speed in older adults. PMID:27090485

  4. The influence of ACE ID and ACTN3 R577X polymorphisms on lower-extremity function in older women in response to high-speed power training

    PubMed Central

    2013-01-01

    Background We studied the influence of the ACE I/D and ACTN3 R577X polymorphisms (single or combined) on lower-extremity function in older women in response to high-speed power training. Methods One hundred and thirty-nine healthy older Caucasian women participated in this study (age: 65.5 ± 8.2 years, body mass: 67.0 ± 10.0 kg and height: 1.57 ± 0.06 m). Walking speed (S10) performance and functional capacity assessed by the “get-up and go” (GUG) mobility test were measured at baseline (T1) and after a consecutive 12-week period of high-speed power training (40-75% of one repetition maximum in arm and leg extensor exercises; 3 sets 4–12 reps, and two power exercises for upper and lower extremity). Genomic DNA was extracted from blood samples, and genotyping analyses were performed by PCR methods. Genotype distributions between groups were compared by Chi-Square test and the gains in physical performance were analyzed by two-way, repeated-measures ANOVA. Results There were no significant differences between genotype groups in men or women for adjusted baseline phenotypes (P > 0.05). ACE I/D and ACTN3 polymorphisms showed a significant interaction genotype-training only in S10 (P = 0.012 and P = 0.044, respectively) and not in the GUG test (P = 0.311 and P = 0.477, respectively). Analyses of the combined effects between genotypes showed no other significant differences in all phenotypes (P < 0.05) at baseline. However, in response to high-speed power training, a significant interaction on walking speed (P = 0.048) was observed between the “power” (ACTN3 RR + RX & ACE DD) versus “non-power” muscularity-oriented genotypes (ACTN3 XX & ACE II + ID)]. Conclusions Thus, ACE I/D and ACTN3 R577X polymorphisms are likely candidates in the modulation of exercise-related gait speed phenotype in older women but not a significant influence in mobility traits. PMID:24313907

  5. An artificial neural network system for diagnosing gas turbine engine fuel faults

    SciTech Connect

    Illi, O.J. Jr.; Greitzer, F.L.; Kangas, L.J.; Reeve, T.

    1994-04-01

    The US Army Ordnance Center & School and Pacific Northwest Laboratories are developing a turbine engine diagnostic system for the M1A1 Abrams tank. This system employs Artificial Neural Network (AN) technology to perform diagnosis and prognosis of the tank`s AGT-1500 gas turbine engine. This paper describes the design and prototype development of the ANN component of the diagnostic system, which we refer to as ``TEDANN`` for Turbine Engine Diagnostic Artificial Neural Networks.

  6. Excitability of the soleus reflex arc during intensive stretch-shortening cycle exercise in two power-trained athlete groups.

    PubMed

    Avela, Janne; Finni, Jarkko; Komi, Paavo V

    2006-07-01

    In several explosive types of sport events the leg extensor muscles are subjected to very high impact loads. Thus, extreme requirements exist for the neuromuscular system to develop sufficient muscle stiffness in the lower extremities in order to tolerate these high impact loads. Therefore, it would be challenging to measure reflex modulation during high impact activities, and with different athlete populations. In the present experiment, H-reflex and short latency reflex (M1) sensitivity was measured during drop jump exercises among high jumpers and sprinters. The changes in both reflex peak-to-peak amplitudes showed a significant (P < 0.05) reduction towards the end of the exercise for the sprinters. In addition, the same subject group showed a remarkable increase in serum creatine kinase (CK) activity 2 h after the jumps. Similar changes could not be observed for the high jumpers. These results clearly indicate different neural adaptation strategies for the two athlete groups. Reduction in H-reflex sensitivity and an increase in CK-activity in sprinters were taken as evidence for presynaptic inhibition, probably induced by substances related to muscle damage. Since high jump training includes more high impact loading, it was assumed that it could lead to some structural adaptation and, thus, prevents exercise induced reflex modification to a certain extent. PMID:16763835

  7. Recent Updates on the Proximal Tubule Renin-Angiotensin System in Angiotensin II-Dependent Hypertension.

    PubMed

    Li, Xiao C; Zhuo, Jia L

    2016-08-01

    It is well recognized that the renin-angiotensin system (RAS) exists not only as circulating, paracrine (cell to cell), but also intracrine (intracellular) system. In the kidney, however, it is difficult to dissect the respective contributions of circulating RAS versus intrarenal RAS to the physiological regulation of proximal tubular Na(+) reabsorption and hypertension. Here, we review recent studies to provide an update in this research field with a focus on the proximal tubular RAS in angiotensin II (ANG II)-induced hypertension. Careful analysis of available evidence supports the hypothesis that both local synthesis or formation and AT1 (AT1a) receptor- and/or megalin-mediated uptake of angiotensinogen (AGT), ANG I and ANG II contribute to high levels of ANG II in the proximal tubules of the kidney. Under physiological conditions, nearly all major components of the RAS including AGT, prorenin, renin, ANG I, and ANG II would be filtered by the glomerulus and taken up by the proximal tubules. In ANG II-dependent hypertension, the expression of AGT, prorenin, and (pro)renin receptors, and angiotensin-converting enzyme (ACE) is upregulated rather than downregulated in the kidney. Furthermore, hypertension damages the glomerular filtration barrier, which augments the filtration of circulating AGT, prorenin, renin, ANG I, and ANG II and their uptake in the proximal tubules. Together, increased local ANG II formation and augmented uptake of circulating ANG II in the proximal tubules, via activation of AT1 (AT1a) receptors and Na(+)/H(+) exchanger 3, may provide a powerful feedforward mechanism for promoting Na(+) retention and the development of ANG II-induced hypertension. PMID:27372447

  8. Deficiency of angiotensinogen in hepatocytes markedly decreases blood pressure in lean and obese male mice.

    PubMed

    Yiannikouris, Frederique; Wang, Yu; Shoemaker, Robin; Larian, Nika; Thompson, Joel; English, Victoria L; Charnigo, Richard; Su, Wen; Gong, Ming; Cassis, Lisa A

    2015-10-01

    We recently demonstrated that adipocyte deficiency of angiotensinogen (AGT) ablated high-fat diet-induced elevations in plasma angiotensin II (Ang II) concentrations and obesity-hypertension in male mice. Hepatocytes are the predominant source of systemic AGT. Therefore, in this study, we defined the contribution of hepatocyte-derived AGT to obesity-induced elevations in plasma AGT concentrations and hypertension. Male Agt(fl/fl) mice expressing albumin-driven Cre recombinase were bred to female Agt(fl/fl) mice to generate Agt(fl/fl) or hepatocyte AGT-deficient male mice (Agt(Alb)). Mice were fed a low-fat or high-fat diet for 16 weeks. Hepatocyte AGT deficiency had no significant effect on body weight. Plasma AGT concentrations were increased in obese Agt(fl/fl) mice. Hepatocyte AGT deficiency markedly reduced plasma AGT and Ang II concentrations in lean and obese mice. Moreover, hepatocyte AGT deficiency reduced the content and release of AGT from adipose explants. Systolic blood pressure was markedly decreased in lean (by 18 mm Hg) and obese Agt(Alb) mice (by 54 mm Hg) compared with Agt(fl/fl) controls. To define mechanisms, we quantified effects of Ang II on mRNA abundance of megalin, an AGT uptake transporter, in 3T3-L1 adipocytes. Ang II stimulated adipocyte megalin mRNA abundance and decreased media AGT concentrations. These results demonstrate that hepatocytes are the predominant source of systemic AGT in both lean and obese mice. Moreover, reductions in plasma angiotensin concentrations in obese hepatocyte AGT-deficient mice may have limited megalin-dependent uptake of AGT into adipocytes for the production of Ang II in the development of obesity-hypertension. PMID:26303292

  9. ACE I/D and ACTN3 R/X polymorphisms as potential factors in modulating exercise-related phenotypes in older women in response to a muscle power training stimuli.

    PubMed

    Pereira, Ana; Costa, Aldo M; Izquierdo, Mikel; Silva, António J; Bastos, Estela; Marques, Mário C

    2013-10-01

    Genetic variation of the human ACE I/D and ACTN3 R577X polymorphisms subsequent to 12 weeks of high-speed power training on maximal strength (1RM) of the arm and leg muscles, muscle power performance (counter-movement jump), and functional capacity (sit-to-stand test) was examined in older Caucasian women [n = 139; mean age 65.5 (8.2) years; 67.0 (10.0) kg and 1.57 (0.06) m]. Chelex 100 was used for DNA extraction, and genotype was determined by PCR-RFLP methods. Muscular strength, power, and functional testing were conducted at baseline (T1) and after 12 weeks (T2) of high-speed power training. At baseline, the ACE I/D and ACTN3 R/X polymorphisms were not associated with muscle function or muscularity phenotypes in older Caucasian women. After the 12-week high-speed training program, subjects significantly increased their muscular and functional capacity performance (p < 0.05). For both polymorphisms, significant genotype-training interaction (p < 0.05) was found in all muscular performance indices, except for 1RM leg extension in the ACE I/D (p = 0.187). Analyses of the combined effects between genotypes showed significant differences in all parameters (p < 0.05) in response to high-speed power training between the power (ACTN3 RR + RX & ACE DD) versus "non-power" muscularity-oriented genotypes (ACTN3 XX & ACE II + ID)]. Our data suggest that the ACE and ACTN3 genotypes (single or combined) exert a significant influence in the muscle phenotypes of older Caucasian women in response to high-speed power training. Thus, the ACE I/D and ACTN3 R/X polymorphisms are likely factors in modulating exercise-related phenotypes in older women, particularly in response to a resistance training stimuli. PMID:22855367

  10. Renin-angiotensin system genes polymorphism in Egyptians with premature coronary artery disease.

    PubMed

    Abd El-Aziz, Tarek A; Hussein, Yousri M; Mohamed, Randa H; Shalaby, Sally M

    2012-05-01

    Genetics polymorphism of the renin-angiotensin system (RAS) affects the pathogenesis of atherosclerosis and associated with coronary artery disease (CAD). We aimed to investigate the association between the RAS genes and premature CAD (PCAD) in Egyptians. 116 patients with PCAD, 114 patients with late onset CAD and 119 controls were included in the study. Angiotensin converting enzyme (ACE), angiotensin II receptor type 1 (ATR1) and angiotensinogen (AGT) genes polymorphisms were analyzed by polymerase chain reaction (PCR). We found that ACE DD, AGT TT and ATR1 CC increased the risk of PCAD by 2.7, 2.8 and 2.86 respectively). Smoking, hypertension, diabetes, total cholesterol, triglycerides and LDL cholesterol were independent risk factors for the development of PCAD. We conclude that the ACE DD, AGT TT and ATR1 CC genotypes may increase the susceptibility of an individual to have PCAD. The coexistence of CAD risk factors with these risky RAS genotypes may lead to the development of PCAD in Egyptian patients. PMID:22387727

  11. Molecular characterization and transcriptional regulation of the renin-angiotensin system genes in Senegalese sole (Solea senegalensis Kaup, 1858): differential gene regulation by salinity.

    PubMed

    Armesto, Paula; Cousin, Xavier; Salas-Leiton, Emilio; Asensio, Esther; Manchado, Manuel; Infante, Carlos

    2015-06-01

    In this work, the complete cDNA sequence encoding angiotensinogen (agt) in the euryhaline flatfish Senegalese sole was obtained. Additionally, putative coding sequences belonging to other renin-angiotensin system (RAS) genes including renin (ren), angiotensin-converting enzyme (ace), angiotensin-converting enzyme 2 (ace2), as well as angiotensin II receptor type I (agtr1) and type II (agtr2), were also identified. In juvenile tissues, agt transcripts were mainly detected in liver, ren in kidney, ace and ace2 in intestine, agtr1 in kidney and brain, and agtr2 in liver and kidney. Expression analysis of the six RAS genes after a salinity shift revealed a clear increase of agt mRNA abundance in liver just after transferring soles to high salinity water (60 ppt) with a peak at 48 h. Moreover, gene expression analysis in gills showed transcriptional regulation of ace and agtr1 at 48 h and agtr2 at 96 h after transferring soles to 60 ppt. Incubation of larvae before mouth opening (until 3 days post hatch; dph) at low salinity (10 ppt) resulted in a coordinated transcriptional up-regulation of RAS genes. Nevertheless, no differences in mRNA abundance between salinities were observed when larvae were cultivated to low salinity after mouth opening. Whole-mount in situ hybridization (WISH) signal for agt and ace in 3 dph larvae incubated at 10 ppt and 35 ppt confirmed that the former gene was mainly expressed in liver whereas the later gene was mainly located in pharynx and posterior gut, without pronounced differences in intensity between salinities. Possible physiological significance of all these results is discussed. PMID:25645294

  12. Renin–angiotensin–aldosterone system related gene polymorphisms and urinary total arsenic is related to chronic kidney disease

    SciTech Connect

    Chen, Wei-Jen; Huang, Ya-Li; Shiue, Horng-Sheng; Chen, Tzen-Wen; Lin, Yuh-Feng; Huang, Chao-Yuan; Lin, Ying-Chin; Han, Bor-Cheng; Hsueh, Yu-Mei

    2014-09-01

    A recent study demonstrated that an increased risk of chronic kidney disease (CKD) was associated with high urinary total arsenic levels. However, whether genomic instability is related to CKD remains unclear. An association between CKD and genetic polymorphisms of regulation enzymes of the renin–angiotensin–aldosterone system (RAAS), such as angiotensin-converting enzyme (ACE), angiotensinogen (AGT), angiotensin II type I receptor (AT1R), and aldosterone synthase (CYP11B2) has not been shown. The aim of the present study was to investigate the relationship between arsenic, genetic polymorphisms of RAAS enzymes and CKD. A total of 233 patients and 449 age- and gender-matched controls were recruited from the Taipei Medical University Hospital, Taipei Municipal Wan Fang Hospital and the Shin Kong Wu Ho-Su Memorial Hospital. Concentrations of urinary arsenic were determined by a high-performance liquid chromatography-linked hydride generator, and atomic absorption spectrometry. Polymorphisms of ACE(I/D), AGT(A[− 20]C), (T174M), (M235T), AT1R(A1166C) and CYP11B2(C[− 344]T) were examined by polymerase chain reaction and restriction fragment length polymorphism. Subjects carrying the CYP11B2 TT genotype had a higher odds ratio (OR), 1.39 (0.96–2.01), of CKD; while those with the AGT(A[− 20]C) CC genotype had an inverse OR of CKD (0.20 (0.05–0.81)), and a high-risk genotype was defined as A/A + A/C for AGT(A[− 20C]) and T/T for CYP11B2(C[− 344]T). The trend test showed a higher OR for CKD in patients who had either high urinary total arsenic levels or carried the high-risk genotype, or both, compared to patients with low urinary total arsenic levels, who carried the low-risk genotype, and could also be affected by the hypertension or diabetes status. - Highlights: • AGT(− 20 C) and CYP11B2(− 344 T) genotypes were significantly associated with CKD. • Combined effect of high-risk genotypes and high urinary total arsenic on OR of CKD. • Combined

  13. Activation of systemic, but not local, renin-angiotensin system is associated with upregulation of TNF-α during prolonged fasting in northern elephant seal pups.

    PubMed

    Suzuki, Miwa; Vázquez-Medina, José Pablo; Viscarra, Jose A; Soñanez-Organis, José G; Crocker, Daniel E; Ortiz, Rudy M

    2013-09-01

    Northern elephant seal pups naturally endure a 2-3 month post-weaning fast that is associated with activation of systemic renin-angiotensin system (RAS), a decrease in plasma adiponectin (Acrp30), and insulin resistance (IR)-like conditions. Angiotensin II (Ang II) and tumor necrosis factor-alpha (TNF-α) are potential causal factors of IR, while Acrp30 may improve insulin signaling. However, the effects of fasting-induced activation of RAS on IR-like conditions in seals are not well described. To assess the effects of prolonged food deprivation on systemic and local RAS, and their potential contribution to TNF-α as they relate to an IR condition, the mRNA expressions of adipose and muscle RAS components and immuno-relevant molecules were measured along with plasma RAS components. Mean plasma renin activity and Ang II concentrations increased by 89 and 1658%, respectively, while plasma angiotensinogen (AGT) decreased by 49% over the fast, indicative of systemic RAS activation. Prolonged fasting was associated with decreases in adipose and muscle AGT mRNA expressions of 69 and 68%, respectively, corresponding with decreases in tissue protein content, suggesting suppression of local AGT production. Muscle TNF-α mRNA and protein increased by 239 and 314%, whereas those of adipose Acrp30 decreased by 32 and 98%, respectively. Collectively, this study suggests that prolonged fasting activates a systemic RAS, which contributes to an increase in muscle TNF-α and suppression of adipose Acrp30. This targeted and tissue-specific regulation of TNF-α and Acrp30 is likely coordinated to synergistically contribute to the development of an IR-like condition, independent of local RAS activity. These data enhance our understanding of the adaptive mechanisms evolved by elephant seals to tolerate potentially detrimental conditions. PMID:23685967

  14. Adipocyte-specific deficiency of angiotensinogen decreases plasma angiotensinogen concentration and systolic blood pressure in mice.

    PubMed

    Yiannikouris, Frederique; Karounos, Michael; Charnigo, Richard; English, Victoria L; Rateri, Debra L; Daugherty, Alan; Cassis, Lisa A

    2012-01-15

    Previous studies demonstrated that overexpression of angiotensinogen (AGT) in adipose tissue increased blood pressure. However, the contribution of endogenous AGT in adipocytes to the systemic renin-angiotensin system (RAS) and blood pressure control is undefined. To define a role of adipocyte-derived AGT, mice with loxP sites flanking exon 2 of the AGT gene (Agt(fl/fl)) were bred to transgenic mice expressing Cre recombinase under the control of an adipocyte fatty acid-binding protein 4 promoter (aP2) promoter to generate mice with adipocyte AGT deficiency (Agt(aP2)). AGT mRNA abundance in adipose tissue and AGT secretion from adipocytes were reduced markedly in adipose tissues of Agt(aP2) mice. To determine the contribution of adipocyte-derived AGT to the systemic RAS and blood pressure control, mice were fed normal laboratory diet for 2 or 12 mo. In males and females of each genotype, body weight and fat mass increased with age. However, there was no effect of adipocyte AGT deficiency on body weight, fat mass, or adipocyte size. At 2 and 12 mo of age, mice with deficiency of AGT in adipocytes had reduced plasma concentrations of AGT (by 24-28%) compared with controls. Moreover, mice lacking AGT in adipocytes exhibited reduced systolic blood pressures compared with controls (Agt(fl/fl), 117 ± 2; Agt(aP2), 110 ± 2 mmHg; P < 0.05). These results demonstrate that adipocyte-derived AGT contributes to the systemic RAS and blood pressure control. PMID:22071160

  15. Tractor Mechanics. Maintaining and Servicing the Power Train, Learning Activity Packages 49-53; Maintaining and Servicing the Clutch, Learning Activity Packages 54-59; Maintaining and Servicing the Transmission and Differential, Learning Activity Packages 60-68; Maintaining and Servicing the Final Drive, Learning Activity Packages 69-77.

    ERIC Educational Resources Information Center

    Clemson Univ., SC. Vocational Education Media Center.

    This series of learning activity packages focuses on four areas of tractor mechanics: (1) maintaining and servicing the power train, (2) maintaining and servicing the clutch, (3) maintaining and servicing the transmission and differential, and (4) maintaining and servicing the final drive. Each of the twenty-nine illustrated learning activity…

  16. Interim assessment of the VAL automated guideway transit system. Interim report

    SciTech Connect

    Anagnostopoulos, G.

    1981-11-01

    This report describes an interim assessment of the VAL (Vehicules Automatiques Legers or Light Automated Vehicle) AGT system which is currently under construction in Lille, France, and which is to become fully operational in December 1983. This report contains a technical description and performance data resulting from a demonstration test program performed concurrently in August 1980. VAL is the first driverless AGT urban system application in France. The system operates at grade, elevated, and in tunnels on an exclusive concrete dual-lane guideway that is 12.7 kilometers long. The configuration of the system is a push-pull loop operating between 17 on-line stations. The system is designed to provide scheduled operation at 60-second headways and a normal one-way capacity of 7440 passengers per hour per direction with 55 percent of the passengers seated. Two pneumatic-tired vehicles are coupled into a single vehicle capable of carrying 124 passengers at line speeds of 60 km/hr. During the course of the demonstration test program, VAL demonstrated that it could achieve high levels of dependability and availability and could perform safely under all perceivable conditions.

  17. Living high training low induces physiological cardiac hypertrophy accompanied by down-regulation and redistribution of the renin-angiotensin system

    PubMed Central

    Shi, Wei; Meszaros, J Gary; Zeng, Shao-ju; Sun, Ying-yu; Zuo, Ming-xue

    2013-01-01

    Aim: Living high training low” (LHTL) is an exercise-training protocol that refers living in hypoxia stress and training at normal level of O2. In this study, we investigated whether LHTL caused physiological heart hypertrophy accompanied by changes of biomarkers in renin-angiotensin system in rats. Methods: Adult male SD rats were randomly assigned into 4 groups, and trained on living low-sedentary (LLS, control), living low-training low (LLTL), living high-sedentary (LHS) and living high-training low (LHTL) protocols, respectively, for 4 weeks. Hematological parameters, hemodynamic measurement, heart hypertrophy and plasma angiotensin II (Ang II) level of the rats were measured. The gene and protein expression of angiotensin-converting enzyme (ACE), angiotensinogen (AGT) and angiotensin II receptor I (AT1) in heart tissue was assessed using RT-PCR and immunohistochemistry, respectively. Results: LLTL, LHS and LHTL significantly improved cardiac function, increased hemoglobin concentration and RBC. At the molecular level, LLTL, LHS and LHTL significantly decreased the expression of ACE, AGT and AT1 genes, but increased the expression of ACE and AT1 proteins in heart tissue. Moreover, ACE and AT1 protein expression was significantly increased in the endocardium, but unchanged in the epicardium. Conclusion: LHTL training protocol suppresses ACE, AGT and AT1 gene expression in heart tissue, but increases ACE and AT1 protein expression specifically in the endocardium, suggesting that the physiological heart hypertrophy induced by LHTL is regulated by region-specific expression of renin-angiotensin system components. PMID:23377552

  18. Structure and functions of angiotensinogen

    PubMed Central

    Lu, Hong; Cassis, Lisa A; Kooi, Craig W Vander; Daugherty, Alan

    2016-01-01

    Angiotensinogen (AGT) is the sole precursor of all angiotensin peptides. Although AGT is generally considered as a passive substrate of the renin–angiotensin system, there is accumulating evidence that the regulation and functions of AGT are intricate. Understanding the diversity of AGT properties has been enhanced by protein structural analysis and animal studies. In addition to whole-body genetic deletion, AGT can be regulated in vivo by cell-specific procedures, adeno-associated viral approaches and antisense oligonucleotides. Indeed, the availability of these multiple manipulations of AGT in vivo has provided new insights into the multifaceted roles of AGT. In this review, the combination of structural and functional studies is highlighted to focus on the increasing recognition that AGT exerts effects beyond being a sole provider of angiotensin peptides. PMID:26888118

  19. Novel Mechanism of Blood Pressure Regulation By Foxo1-Mediated Transcriptional Control of Hepatic Angiotensinogen

    PubMed Central

    Qi, Yajuan; Zhang, Kebin; Wu, Yuxin; Xu, Zihui; Yong, QC; Kumar, Rajesh; Baker, Kenneth M.; Zhu, Qinglei; Chen, Shouwen; Guo, Shaodong

    2014-01-01

    The renin-angiotensin system (RAS) is a major determinant of blood pressure regulation. It consists of a cascade of enzymatic reactions involving three components: angiotensinogen (Agt), renin, and angiotensin-converting enzyme (ACE), which generate angiotensin II (Ang II) as a biologically active product. Agt is largely produced in the liver, acting as a major determinant of the circulating RAS, which exerts acute hemodynamic effects on blood pressure regulation. How the expression of Agt is regulated is not completely understood. Here we hypothesize that Agt is regulated by forkhead transcription factor forkhead box class O1 (Foxo1), an insulin-suppressed transcription factor, and thereby controls blood pressure in mice. We generated liver-specific Foxo1 knockout mice (L-F1KO mice), which exhibited a reduction in plasma Agt and Ang II levels and a significant decrease in blood pressure. Using hepatocyte cultures, we demonstrated that overexpression of Foxo1 increased Agt expression, while hepatocytes lacking Foxo1 demonstrated a reduction of Agt gene expression and partially impaired insulin inhibition on Agt gene expression. Furthermore, mouse Agt prompter analysis demonstrated that the Agt promoter region contains a functional Foxo1 binding site, which is responsible for both Foxo1 stimulation and insulin suppression on the promoter activity. Together, these data demonstrate that Foxo1 regulates hepatic Agt gene expression and controls plasma Agt and Ang II levels, modulating blood pressure control in mice. PMID:25069665

  20. Uric acid induces oxidative stress via an activation of the renin-angiotensin system in 3T3-L1 adipocytes.

    PubMed

    Zhang, Jun-xia; Zhang, Yu-ping; Wu, Qi-nan; Chen, Bing

    2015-02-01

    Hyperuricemia is recently reported involving in various obesity-related cardiovascular disorders, especially hypertension. However, the underlying mechanisms are not completely understood. In the present study, we investigated whether uric acid upregulates renin-angiotensin system (RAS) expression in adipocytes. We also examined whether RAS activation plays a role in uric acid-induced oxidative stress in adipocytes. The adipocytes of different phenotypes were incubated with uric acid for 48 h, respectively. Losartan (10(-4) M) or captopril (10(-4) M) was used to block adipose tissue RAS activation. mRNA expressions of angiotensinogen (AGT), angiotensin-converting enzyme-1 (ACE-1), renin, angiotensin type 1 receptor (AT1R), and angiotensin type 2 receptor (AT2R) were evaluated with real-time PCR. Angiotensin II concentrations in supernatant were measured by ELISA. Intracellular reactive species (ROS) levels were measured by fluorescent probe DCFH-DA, DHR, or NBT assay. The uric acid upregulated both RAS (AGT, ACE1, renin, AT1R, and AT2R) mRNA expressions and angiotensin II protein secretion and caused a significant increase in ROS production in 3T3-L1 adipocytes. These effects could be prevented by RAS inhibitors, either losartan or captopril. RAS activation has been causally implicated in oxidative stress induced by uric acid in 3T3-L1 adipocytes, suggesting a plausible mechanism through which hyperuricemia contributes to the pathogenesis of obesity-related cardiovascular diseases. PMID:24671741

  1. Angiotensin III: a physiological relevant peptide of the renin angiotensin system.

    PubMed

    Yugandhar, Vudhya G; Clark, Michelle A

    2013-08-01

    The renin angiotensin system (RAS) is a peptide hormone system that plays an important role in the pathophysiology of various diseases, including congestive heart failure, hypertension, myocardial infarction, and diabetic nephropathy. This has led researchers to focus extensively on this system, leading to the discovery of various peptides, peptidases, receptors and signal transduction mechanisms intrinsic to the RAS. Angiotensinogen (AGT), angiotensin (Ang) II, Ang III, Ang IV, and Ang-(1-7) are the main biologically active peptides of RAS. However, most of the available studies have focused on Ang II as the likely key peptide from the RAS that directly and indirectly regulates physiological functions leading to pathological conditions. However, data from recent studies suggest that Ang III may produce physiologically relevant effects that are similar to those produced by Ang II. Hence, this review focuses on Ang III and the myriad of physiological effects that it produces in the body. PMID:23692861

  2. Coupled dynamics analysis of wind energy systems

    NASA Technical Reports Server (NTRS)

    Hoffman, J. A.

    1977-01-01

    A qualitative description of all key elements of a complete wind energy system computer analysis code is presented. The analysis system addresses the coupled dynamics characteristics of wind energy systems, including the interactions of the rotor, tower, nacelle, power train, control system, and electrical network. The coupled dynamics are analyzed in both the frequency and time domain to provide the basic motions and loads data required for design, performance verification and operations analysis activities. Elements of the coupled analysis code were used to design and analyze candidate rotor articulation concepts. Fundamental results and conclusions derived from these studies are presented.

  3. Cardiac angiotensin-(1-12) expression and systemic hypertension in rats expressing the human angiotensinogen gene.

    PubMed

    Ferrario, Carlos M; VonCannon, Jessica; Jiao, Yan; Ahmad, Sarfaraz; Bader, Michael; Dell'Italia, Louis J; Groban, Leanne; Varagic, Jasmina

    2016-04-15

    Angiotensin-(1-12) [ANG-(1-12)] is processed into ANG II by chymase in rodent and human heart tissue. Differences in the amino acid sequence of rat and human ANG-(1-12) render the human angiotensinogen (hAGT) protein refractory to cleavage by renin. We used transgenic rats harboring the hAGT gene [TGR(hAGT)L1623] to assess the non-renin-dependent effects of increased hAGT expression on heart function and arterial pressure. Compared with Sprague-Dawley (SD) control rats (n= 11), male homozygous TGR(hAGT)L1623 (n= 9) demonstrated sustained daytime and nighttime hypertension associated with no changes in heart rate but increased heart rate lability. Increased heart weight/tibial length ratio and echocardiographic indexes of cardiac hypertrophy were associated with modest reduction of systolic function in hAGT rats. Robust human ANG-(1-12) immunofluorescence within myocytes of TGR(hAGT)L1623 rats was associated with a fourfold increase in cardiac ANG II content. Chymase enzymatic activity, using the rat or human ANG-(1-12) as a substrate, was not different in the cardiac tissue of SD and hAGT rats. Since both cardiac angiotensin-converting enzyme (ACE) and ACE2 activities were not different among the two strains, the changes in cardiac structure and function, blood pressure, and left ventricular ANG II content might be a product of an increased cardiac expression of ANG II generated through a non-renin-dependent mechanism. The data also underscore the existence in the rat of alternate enzymes capable of acting on hAGT protein. Homozygous transgenic rats expressing the hAGT gene represent a novel tool to investigate the contribution of human relevant renin-independent cardiac ANG II formation and function. PMID:26873967

  4. Intrarenal mouse renin-angiotensin system during ANG II-induced hypertension and ACE inhibition.

    PubMed

    Gonzalez-Villalobos, Romer A; Satou, Ryousuke; Ohashi, Naro; Semprun-Prieto, Laura C; Katsurada, Akemi; Kim, Catherine; Upchurch, G M; Prieto, Minolfa C; Kobori, Hiroyuki; Navar, L Gabriel

    2010-01-01

    Angiotensin-converting enzyme (ACE) inhibition (ACEi) ameliorates the development of hypertension and the intrarenal ANG II augmentation in ANG II-infused mice. To determine if these effects are associated with changes in the mouse intrarenal renin-angiotensin system, the expression of angiotensinogen (AGT), renin, ACE, angiotensin type 1 receptor (AT(1)R) mRNA (by quanitative RT-PCR) and protein [by Western blot (WB) and/or immunohistochemistry (IHC)] were analyzed. C57BL/6J male mice (9-12 wk old) were distributed as controls (n = 10), ANG II infused (ANG II = 8, 400 ng x kg(-1) x min(-1) for 12 days), ACEi only (ACEi = 10, lisinopril, 100 mg/l), and ANG II infused + ACEi (ANG II + ACEi = 11). When compared with controls (1.00), AGT protein (by WB) was increased by ANG II (1.29 +/- 0.13, P < 0.05), and this was not prevented by ACEi (ACEi + ANG II, 1.31 +/- 0.14, P < 0.05). ACE protein (by WB) was increased by ANG II (1.21 +/- 0.08, P < 0.05), and it was reduced by ACEi alone (0.88 +/- 0.07, P < 0.05) or in combination with ANG II (0.80 +/- 0.07, P < 0.05). AT(1)R protein (by WB) was increased by ANG II (1.27 +/- 0.06, P < 0.05) and ACEi (1.17 +/- 0.06, P < 0.05) but not ANG II + ACEi [1.15 +/- 0.06, not significant (NS)]. Tubular renin protein (semiquantified by IHC) was increased by ANG II (1.49 +/- 0.23, P < 0.05) and ACEi (1.57 +/- 0.15, P < 0.05), but not ANG II + ACEi (1.10 +/- 0.15, NS). No significant changes were observed in AGT, ACE, or AT(1)R mRNA. In summary, reduced responses of intrarenal tubular renin, ACE, and the AT(1)R protein to the stimulatory effects of chronic ANG II infusions, in the presence of ACEi, are associated with the effects of this treatment to ameliorate augmentations in blood pressure and intrarenal ANG II content during ANG II-induced hypertension. PMID:19846570

  5. Intrarenal mouse renin-angiotensin system during ANG II-induced hypertension and ACE inhibition

    PubMed Central

    Satou, Ryousuke; Ohashi, Naro; Semprun-Prieto, Laura C.; Katsurada, Akemi; Kim, Catherine; Upchurch, G. M.; Prieto, Minolfa C.; Kobori, Hiroyuki; Navar, L. Gabriel

    2010-01-01

    Angiotensin-converting enzyme (ACE) inhibition (ACEi) ameliorates the development of hypertension and the intrarenal ANG II augmentation in ANG II-infused mice. To determine if these effects are associated with changes in the mouse intrarenal renin-angiotensin system, the expression of angiotensinogen (AGT), renin, ACE, angiotensin type 1 receptor (AT1R) mRNA (by quanitative RT-PCR) and protein [by Western blot (WB) and/or immunohistochemistry (IHC)] were analyzed. C57BL/6J male mice (9–12 wk old) were distributed as controls (n = 10), ANG II infused (ANG II = 8, 400 ng·kg−1·min−1 for 12 days), ACEi only (ACEi = 10, lisinopril, 100 mg/l), and ANG II infused + ACEi (ANG II + ACEi = 11). When compared with controls (1.00), AGT protein (by WB) was increased by ANG II (1.29 ± 0.13, P < 0.05), and this was not prevented by ACEi (ACEi + ANG II, 1.31 ± 0.14, P < 0.05). ACE protein (by WB) was increased by ANG II (1.21 ± 0.08, P < 0.05), and it was reduced by ACEi alone (0.88 ± 0.07, P < 0.05) or in combination with ANG II (0.80 ± 0.07, P < 0.05). AT1R protein (by WB) was increased by ANG II (1.27 ± 0.06, P < 0.05) and ACEi (1.17 ± 0.06, P < 0.05) but not ANG II + ACEi [1.15 ± 0.06, not significant (NS)]. Tubular renin protein (semiquantified by IHC) was increased by ANG II (1.49 ± 0.23, P < 0.05) and ACEi (1.57 ± 0.15, P < 0.05), but not ANG II + ACEi (1.10 ± 0.15, NS). No significant changes were observed in AGT, ACE, or AT1R mRNA. In summary, reduced responses of intrarenal tubular renin, ACE, and the AT1R protein to the stimulatory effects of chronic ANG II infusions, in the presence of ACEi, are associated with the effects of this treatment to ameliorate augmentations in blood pressure and intrarenal ANG II content during ANG II-induced hypertension. PMID:19846570

  6. Polymorphisms of Renin-Angiotensin-Aldosterone System Gene in Chinese Han Patients with Nonfamilial Atrial Fibrillation

    PubMed Central

    Zhao, Li-qun; Wen, Zu-jia; Wei, Yong; Xu, Juan; Chen, Zheng; Qi, Bao-zhen; Wang, Zhi-ming; Shi, Yong-yong; Liu, Shao-wen

    2015-01-01

    Background Atrial fibrillation(AF) is the most common arrhythmia in the adult population. The activated renin-angiotensin-aldosterone system (RAS) has been reported to play an important role in the pathogenesis of atrial fibrillation. The aim of this study was to investigate the association between nonfamilial AF and polymorphisms in RAS gene. Methods A total of 931 patients with nonfamilial AF, 663 non-AF heart disease patients and 727 healthy subjects were selected. 10 tagSNPs (tSNPs) (ACE gene rs8066114, AGT gene rs7539020, rs3789678, rs2478544, rs11568023, rs2478523, rs4762, rs699 and CYP11B2 rs3802230, rs3097) were chosen and genotyped in our study. Single-locus analysis and haplotype analysis were used in this study. Results In single-locus analysis, we found rs11568023 and rs3789678 in AGT gene were associated with nonfamilial AF in Chinese Han population. AF risk was associated with rs3789678 between the AF group and control groups. Under dominant model, the significant AF risk was observed in rs3789678 between the AF group and non AF heart control group; And the protective effect was found in rs11568023, compared with the non-AF heart disease control group. In multilocus haplotype analysis, the association between frequencies of the haplotypes and AF risk was showed in AGT gene (rs7539020-rs3789678), compared ‘TT’ haplotype with the common ‘TC’ haplotype, adjusted for age, gender, LVEF, LVEDD, LAD and frequency of hypertension and diabetes. The diplotype with ‘TC’, carrying rs3789678-C-allele, was associated with reduced risk of AF between the AF group and the healthy control group. The diplotype with ‘TT’ haplotype in the same block, carrying rs3789678-T-allele, was associated with increased risk of AF. Conclusions Via a large-scale case-control study, we found that rs3789678 site was potential susceptible locus of AF whereas rs11568023 was protective factor. PMID:25723521

  7. Hydrogen release properties of lithium alanate for application to fuel cell propulsion systems

    NASA Astrophysics Data System (ADS)

    Corbo, P.; Migliardini, F.; Veneri, O.

    In this paper the results of an experimental study on LiAlH 4 (lithium alanate) as hydrogen source for fuel cell propulsion systems are reported. The compound examined in this work was selected as reference material for light metal hydrides, because of its high hydrogen content (10.5 wt.%) and interesting desorption kinetic properties at moderate temperatures. Thermal dynamic and kinetic of hydrogen release from this hydride were investigated using a fixed bed reactor to evaluate the effect of heating procedure, carrier gas flow rate and sample form. The aim of this study was to characterize the lithium alanate decomposition through the reaction steps leading to the formation of Li 3AlH 6 and LiH. A hydrogen tank was designed and realized to contain pellets of lithium alanate as feeding for a fuel cell propulsion system based on a 2-kW Polymeric Electrolyte Fuel Cell (PEFC) stack. The fuel cell system was integrated into the power train comprising DC-DC converter, energy storage systems and electric drive for moped applications (3 kW). The experiments on the power train were conducted on a test bench able to simulate the vehicle behaviour and road characteristics on specific driving cycles. In particular the efficiencies of individual components and overall power train were analyzed evidencing the energy requirements of the hydrogen storage material.

  8. Fetal sex affects expression of renin-angiotensin system components in term human decidua.

    PubMed

    Wang, Yu; Pringle, Kirsty G; Sykes, Shane D; Marques, Francine Z; Morris, Brian J; Zakar, Tamas; Lumbers, Eugenie R

    2012-01-01

    The maternal decidua expresses the genes of the renin-angiotensin system (RAS). Human decidua was collected at term either before labor (i.e. cesarean delivery) or after spontaneous labor. The mRNA for prorenin (REN), prorenin receptor (ATP6AP2), angiotensinogen (AGT), angiotensin-converting enzymes 1 and 2 (ACE1 and ACE2), angiotensin II type 1 receptor (AGTR1), and angiotensin 1-7 receptor (MAS1) were measured by quantitative real-time RT-PCR. Decidual explants were cultured in duplicate for 24 and 48 h, and all RAS mRNA, and the secretion of prorenin, angiotensin II, and angiotensin 1-7 was measured using quantitative real-time RT-PCR, ELISA, and radioimmunoassay, respectively. In the decidua collected before labor, REN mRNA levels were higher if the fetus was female. In addition, REN, ATP6AP2, AGT, and MAS1 mRNA abundance was greater in decidual explants collected from women carrying a female fetus, as was prorenin protein. After 24 h, ACE1 mRNA was higher in the decidual explants from women with a male fetus, whereas after 48 h, both ACE1 and ACE2 mRNA was higher in decidual explants from women with a female fetus. Angiotensin II was present in all explants, but angiotensin 1-7 levels often registered below the lower limits of sensitivity for the assay. After labor, decidua, when compared with nonlaboring decidua, demonstrated lower REN expression when the fetus was female. Therefore, the maternal decidual RAS is regulated in a sex-specific manner, suggesting that it may function differently when the fetus is male than when it is female. PMID:22045662

  9. Test requirements for 42 V battery systems

    NASA Astrophysics Data System (ADS)

    Weighall, M. J.

    The introduction of the 42 V PowerNet imposes new performance requirements on the battery. The required performance parameters will vary dependent on the application and to what extent the power train is hybridised, with additional features such as start-stop, launch assist etc. This makes it more difficult to specify relevant laboratory test procedures. This paper reviews the vehicle electrical system developments and the impact these developments will have on the battery performance and testing requirements. Suitable test equipment from Digatron/Firing Circuits is discussed and reviewed.

  10. Wind energy system time-domain (WEST) analyzers

    NASA Technical Reports Server (NTRS)

    Dreier, M. E.; Hoffman, J. A.

    1981-01-01

    A portable analyzer which simulates in real time the complex nonlinear dynamics of horizontal axis wind energy systems was constructed. Math models for an aeroelastic rotor featuring nonlinear aerodynamic and inertial terms were implemented with high speed digital controllers and analog calculation. This model was combined with other math models of elastic supports, control systems, a power train and gimballed rotor kinematics. A stroboscopic display system graphically depicting distributed blade loads, motion, and other aerodynamic functions on a cathode ray tube is included. Limited correlation efforts showed good comparison between the results of this analyzer and other sophisticated digital simulations. The digital simulation results were successfully correlated with test data.

  11. H2S Inhibits Hyperglycemia-Induced Intrarenal Renin-Angiotensin System Activation via Attenuation of Reactive Oxygen Species Generation

    PubMed Central

    Ni, Jun; Li, Chen; Shao, Decui; Liu, Jia; Shen, Yang; Wang, Zhen; Zhou, Li; Zhang, Wei; Huang, Yu; Yu, Chen; Wang, Rui; Lu, Limin

    2013-01-01

    Decrease in endogenous hydrogen sulfide (H2S) was reported to participate in the pathogenesis of diabetic nephropathy (DN). This study is aimed at exploring the relationship between the abnormalities in H2S metabolism, hyperglycemia-induced oxidative stress and the activation of intrarenal renin-angiotensin system (RAS). Cultured renal mesangial cells (MCs) and streptozotocin (STZ) induced diabetic rats were used for the studies. The expressions of angiotensinogen (AGT), angiotensin converting enzyme (ACE), angiotensin II (Ang II) type I receptor (AT1), transforming growth factor-β1 (TGF-β1) and collagen IV were measured by real time PCR and Western blot. Reactive oxygen species (ROS) production was assessed by fluorescent probe assays. Cell proliferation was analyzed by 5'-bromo-2'-deoxyuridine incorporation assay. Ang II concentration was measured by an enzyme immunoassay. AGT, ACE and AT1 receptor mRNA levels and Ang II concentration were increased in high glucose (HG) -treated MCs, the cell proliferation rate and the production of TGF-β1 and of collagen IV productions were also increased. The NADPH oxidase inhibitor diphenylenechloride iodonium (DPI) was able to reverse the HG-induced RAS activation and the changes in cell proliferation and collagen synthesis. Supplementation of H2S attenuated HG-induced elevations in ROS and RAS activation. Blockade on H2S biosynthesis from cystathione-γ-lyase (CSE) by DL-propargylglycine (PPG) resulted in effects similar to that of HG treatment. In STZ-induced diabetic rats, the changes in RAS were also reversed by H2S supplementation without affecting blood glucose concentration. These data suggested that the decrease in H2S under hyperglycemic condition leads to an imbalance between oxidative and reductive species. The increased oxidative species results in intrarenal RAS activation, which, in turn, contributes to the pathogenesis of renal dysfunction. PMID:24058553

  12. A systematic review of the role of renin angiotensin aldosterone system genes in diabetes mellitus, diabetic retinopathy and diabetic neuropathy

    PubMed Central

    Rahimi, Zohreh; Moradi, Mahmoudreza; Nasri, Hamid

    2014-01-01

    Background: The renin angiotensin aldosterone system (RAAS) plays a vital role in regulating glucose metabolism and blood pressure, electrolyte and fluid homeostasis. The aim of this systematic review is to assess the association of the RAAS genes with diabetes mellitus (DM) and its complications of retinopathy, neuropathy and cardiovascular disease (CVD). Materials and Methods: The relevant English-language studies were identified using the key words of DM, type 1 diabetes mellitus (T1DM), T2DM, renin angiotensin aldosterone polymorphisms or genotypes and RAAS from the search engines of MEDLINE/PubMed, and Scopus from January 1, 1995 to July 30, 2014. Inclusion criteria for selecting relevant studies were reporting the role of RAAS gene variants in the pathogenesis of T1DM or T2DM, diabetic retinopathy (DR), diabetic neuropathy and cardiovascular complication of DM. Results: The reviewers identified 204 studies of which 73 were eligible for inclusion in the present systematic review. The review indicates the angiotensinogen (AGT) M235T polymorphism might not affect the risk of DM. The role of angiotensin converting enzyme insertion/deletion (ACE I/D) and angiotensin II type 1 receptor gene (AT1R) A1166C polymorphisms in the pathogenesis of DM could not be established. Studies indicate the absence of an association between three polymorphisms of AGT M235T, ACE I/D and AT1R A1166C and DR in DM patients. A protective role for ACE II genotype against diabetic peripheral neuropathy has been suggested. Also, the ACE I/D polymorphism might be associated with the risk of CVD in DM patients. Conclusion: More studies with adequate sample size that investigate the influence of all RAAS gene variants together on the risk of DM and its complications are necessary to provide a more clear picture of the RAAS genes polymorphisms involvement in the pathogenesis of DM and its complications. PMID:25657757

  13. Human placental renin-angiotensin system in normotensive and pre-eclamptic pregnancies at high altitude and after acute hypoxia-reoxygenation insult.

    PubMed

    Kurlak, Lesia O; Mistry, Hiten D; Cindrova-Davies, Tereza; Burton, Graham J; Broughton Pipkin, Fiona

    2016-03-01

    A functioning placental renin-angiotensin system (RAS) appears necessary for uncomplicated pregnancy and is present during placentation, which occurs under low oxygen tensions. Placental RAS is increased in pre-eclampsia (PE), characterised by placental dysfunction and elevated oxidative stress. We investigated the effect of high altitude hypoxia on the RAS and hypoxia-inducible factors (HIFs) by measuring mRNA and protein expression in term placentae from normotensive (NT) and PE women who delivered at sea level or above 3100 m, using an explant model of hypoxia-reoxygenation to assess the impact of acute oxidative stress on the RAS and HIFs. Protein levels of prorenin (P = 0.049), prorenin receptor (PRR; P = 0.0004), and angiotensin type 1 receptor (AT1R, P = 0.006) and type 2 receptor (AT2R, P = 0.002) were all significantly higher in placentae from NT women at altitude, despite mRNA expression being unaffected. However, mRNA expression of all RAS components was significantly lower in PE at altitude than at sea level, yet PRR, angiotensinogen (AGT) and AT1R proteins were all increased. The increase in transcript and protein expression of all the HIFs and NADPH oxidase 4 seen in PE compared to NT at sea level was blunted at high altitude. Experimentally induced oxidative stress stimulated AGT mRNA (P = 0.04) and protein (P = 0.025). AT1R (r = 0.77, P < 0.001) and AT2R (r = 0.81, P < 0.001) mRNA both significantly correlated with HIF-1β, whilst AT2R also correlated with HIF-1α (r = 0.512, P < 0.013). Our observations suggest that the placental RAS is responsive to changes in tissue oxygenation: this could be important in the interplay between reactive oxygen species as cell-signalling molecules for angiogenesis and hence placental development and function. PMID:26574162

  14. Electric vehicle power train instrumentation: Some constraints and considerations

    NASA Technical Reports Server (NTRS)

    Triner, J. E.; Hansen, I. G.

    1977-01-01

    The application of pulse modulation control (choppers) to dc motors creates unique instrumentation problems. In particular, the high harmonic components contained in the current waveforms require frequency response accommodations not normally considered in dc instrumentation. In addition to current sensing, accurate power measurement requires not only adequate frequency response but must also address phase errors caused by the finite bandwidths and component characteristics involved. The implications of these problems are assessed.

  15. MHD Advanced Power Train Phase I, Final Report, Volume 7

    SciTech Connect

    A. R. Jones

    1985-08-01

    This appendix provides additional data in support of the MHD/Steam Power Plant Analyses reported in report Volume 5. The data is in the form of 3PA/SUMARY computer code printouts. The order of presentation in all four cases is as follows: (1) Overall Performance; (2) Component/Subsystem Information; (3) Plant Cost Accounts Summary; and (4) Plant Costing Details and Cost of Electricity.

  16. Electric vehicle power train instrumentation - Some constraints and considerations

    NASA Technical Reports Server (NTRS)

    Triner, J. E.; Hansen, I. G.

    1977-01-01

    The application of pulse modulation control (choppers) to dc motors creates unique instrumentation problems. In particular, the high-harmonic components contained in the current waveforms require frequency-response accommodations not normally considered in dc instrumentation. In addition to current sensing, accurate power measurement not only requires adequate frequency response but also must address phase errors caused by the finite bandwidths and component characteristics involved. This paper discusses the implications of these problems and reports on the degree to which they have been solved at Lewis Research Center.

  17. Mountain Plains Learning Experience Guide: Automotive Repair. Course: Power Train.

    ERIC Educational Resources Information Center

    Schramm, C.; Osland, Walt

    One of twelve individualized courses included in an automotive repair curriculum, this course covers the theory, diagnoses, and overhaul of manual and automatic transmissions, drivelines, and differentials. The course is comprised of five units: (1) Clutches, (2) Standard Transmissions, (3) Automatic Transmissions, (4) Drive Shafts, and (5)…

  18. Wind Energy System Time-domain (WEST) analyzers using hybrid simulation techniques

    NASA Technical Reports Server (NTRS)

    Hoffman, J. A.

    1979-01-01

    Two stand-alone analyzers constructed for real time simulation of the complex dynamic characteristics of horizontal-axis wind energy systems are described. Mathematical models for an aeroelastic rotor, including nonlinear aerodynamic and elastic loads, are implemented with high speed digital and analog circuitry. Models for elastic supports, a power train, a control system, and a rotor gimbal system are also included. Limited correlation efforts show good comparisons between results produced by the analyzers and results produced by a large digital simulation. The digital simulation results correlate well with test data.

  19. Pharmacologic rescue of an enzyme-trafficking defect in primary hyperoxaluria 1.

    PubMed

    Miyata, Non; Steffen, Janos; Johnson, Meghan E; Fargue, Sonia; Danpure, Christopher J; Koehler, Carla M

    2014-10-01

    Primary hyperoxaluria 1 (PH1; Online Mendelian Inheritance in Man no. 259900), a typically lethal biochemical disorder, may be caused by the AGT(P11LG170R) allele in which the alanine:glyoxylate aminotransferase (AGT) enzyme is mistargeted from peroxisomes to mitochondria. AGT contains a C-terminal peroxisomal targeting sequence, but mutations generate an N-terminal mitochondrial targeting sequence that directs AGT from peroxisomes to mitochondria. Although AGT(P11LG170R) is functional, the enzyme must be in the peroxisome to detoxify glyoxylate by conversion to alanine; in disease, amassed glyoxylate in the peroxisome is transported to the cytosol and converted to oxalate by lactate dehydrogenase, leading to kidney failure. From a chemical genetic screen, we have identified small molecules that inhibit mitochondrial protein import. We tested whether one promising candidate, Food and Drug Administration (FDA)-approved dequalinium chloride (DECA), could restore proper peroxisomal trafficking of AGT(P11LG170R). Indeed, treatment with DECA inhibited AGT(P11LG170R) translocation into mitochondria and subsequently restored trafficking to peroxisomes. Previous studies have suggested that a mitochondrial uncoupler might work in a similar manner. Although the uncoupler carbonyl cyanide m-chlorophenyl hydrazone inhibited AGT(P11LG170R) import into mitochondria, AGT(P11LG170R) aggregated in the cytosol, and cells subsequently died. In a cellular model system that recapitulated oxalate accumulation, exposure to DECA reduced oxalate accumulation, similar to pyridoxine treatment that works in a small subset of PH1 patients. Moreover, treatment with both DECA and pyridoxine was additive in reducing oxalate levels. Thus, repurposing the FDA-approved DECA may be a pharmacologic strategy to treat PH1 patients with mutations in AGT because an additional 75 missense mutations in AGT may also result in mistrafficking. PMID:25237136

  20. Suppressing angiotensinogen synthesis attenuates kidney cyst formation in a Pkd1 mouse model.

    PubMed

    Saigusa, Takamitsu; Dang, Yujing; Mullick, Adam E; Yeh, Steve T; Zile, Michael R; Baicu, Catalin F; Bell, P Darwin

    2016-01-01

    Activation of the intrarenal renin angiotensin system (RAS) is believed to play an important role in the development of hypertension and cystogenesis in autosomal dominant polycystic kidney disease (ADPKD). Results of clinical studies testing RAS inhibitors in slowing the progression of cystic disease in ADPKD are inconclusive, and we hypothesized that current RAS inhibitors do not adequately suppress intrarenal RAS. For this study, we compared a novel Gen 2 antisense oligonucleotide (ASO) that inhibits angiotensinogen (Agt) synthesis to lisinopril in adult conditional Pkd1 systemic-knockout mice, a model of ADPKD. Six weeks after Pkd1 global gene knockout, the mice were treated with Agt-ASO (66 mg/kg/wk), lisinopril (100 mg/kg/d), PBS (control), or scrambled ASO (66 mg/kg/wk) for 10 wk, followed by tissue collection. Agt ASO resulted in significant reduction in plasma, liver, and kidney Agt, and increased kidney renin compared with control treatments. Kidneys from Agt-ASO-treated mice were not as enlarged and showed reduced cystic volume compared with lisinopril or control treatments. Blood pressure was better controlled with lisinopril than with Agt-ASO. Agt-ASO suppressed cell proliferation in both cystic and noncystic cells compared with lisinopril and control treatments. However, Agt-ASO did not reduce cell proliferation in liver, which indicates that Agt-ASO targets cell signaling pathways that specifically suppresses cystogenesis in the kidney. These data suggest that Agt-ASO effectively attenuates intrarenal RAS and therefore can be a novel and effective agent for treating ADPKD. PMID:26391272

  1. Changes of urinary angiotensinogen concentration and its association with urinary proteins in diabetic rats

    PubMed Central

    Zhuang, Zhen; Bai, Qiong; A, Lata; Liang, Yaoxian; Zheng, Danxia; Wang, Yue

    2015-01-01

    Objective: It had been reported that angiotensinogen might be a marker for activation of renin-angiotensin system, which was associated with the development of diabetic nephropathy. The purpose of this study was to investigate the functional roles of AGT in DN in vitro. Methods: Diabetic rat models were built by single intraperitoneal injection of streptozotocin. The diabetic rats were divided into three groups, two of the three groups were treated with different doses of losartan, the other diabetic group was as control and normal rats acted as healthy control. In a 12-week investigation, we detected the changes of AGT in all rats’ blood and urine and the association between AGT concentration and RAS activation and urinary proteins were analyzed in this study. Results: The serum AGT of rats had no significant differences (P>0.05 for all). The urinary AGT of the diabetic rats was significantly different from the control group, moreover, the urinary AGT of the diabetic rats under different treatments was also obviously different (P<0.05 for all). Besides, the results of immunohistochemical assay indicated that AGT expression level was correlated with renal tissues damage. The level of AGT was positively associated with urinary protein (r=0.493, P<0.01) and negatively correlated with CCr (r=-0.474, P=0.007) and the dose of ARB (r=-0.575, P=0.001). Moreover, the dose of ARB was independently associated with urinary AGT (B=-2.963, P=0.024) in diabetic rats. Conclusion: Urinary AGT may be a marker for the activation of local RAS in kidney and independently associated with ARB. PMID:26722381

  2. AGT 101: Ceramic component development: Advanced Gas Turbine Program: Topical report, October 1979-July 1987

    SciTech Connect

    Ten Eyck, M.O.; MacBeth, J.W.; Sweeting, T.B.

    1987-11-01

    This topical report summarizes the ceramic component technology development activity conducted by Standard Oil Engineered Materials Company. Standard Oil, acting as a principal subcontractor and supplier of ceramic components, directed its efforts toward the development of ceramic materials in the silicon-carbide family. Various shape forming and fabrication methods, and non-destructive evaluation techniques were explored to produce the static structural components for the ceramic engine. This enabled engine testing to proceed without program slippage, and developed the approaches for producing low-cost, production quantity processes. Standard Oil contributed to the acceptance of ceramics as a viable approach for automotive gas turbine engines and to the advancement of this vital ceramic technology. 174 figs., 33 tabs.

  3. Materials Data on AgTe (SG:62) by Materials Project

    SciTech Connect

    Kristin Persson

    2014-07-09

    Computed materials data using density functional theory calculations. These calculations determine the electronic structure of bulk materials by solving approximations to the Schrodinger equation. For more information, see https://materialsproject.org/docs/calculations

  4. Design and development of a ceramic radial turbine for the AGT101

    NASA Technical Reports Server (NTRS)

    Finger, D. G.; Gupta, S. K.

    1982-01-01

    An acceptable and feasible ceramic turbine wheel design has been achieved, and the relevant temperature, stress, and success probability analyses are discussed. The design is described, the materials selection presented, and the engine cycle conditions analysis parameters shown. Measured MOR four-point strengths are indicated for room and elevated temperatures, and engine conditions are analyzed for various cycle states, materials, power states, turbine inlet temperatures, and speeds. An advanced gas turbine ceramic turbine rotor thermal and stress model is developed, and cumulative probability of survival is shown for first and third-year properties of SiC and Si3N4 rotors under different operating conditions, computed for both blade and hub regions. Temperature and stress distributions for steady-state and worst-case shutdown transients are depicted.

  5. Materials Data on AgTe2Au (SG:51) by Materials Project

    DOE Data Explorer

    Kristin Persson

    2016-02-05

    Computed materials data using density functional theory calculations. These calculations determine the electronic structure of bulk materials by solving approximations to the Schrodinger equation. For more information, see https://materialsproject.org/docs/calculations

  6. Materials Data on AgTe4Au (SG:13) by Materials Project

    DOE Data Explorer

    Kristin Persson

    2015-02-09

    Computed materials data using density functional theory calculations. These calculations determine the electronic structure of bulk materials by solving approximations to the Schrodinger equation. For more information, see https://materialsproject.org/docs/calculations

  7. Generalized Jack polynomials and the AGT relations for the SU(3) group

    NASA Astrophysics Data System (ADS)

    Mironov, S.; Morozov, A.; Zenkevich, Y.

    2014-03-01

    We find generalized Jack polynomials for the SU(3) group and verify that their Selberg averages for several first levels are given by Nekrasov functions. To compute the averages, we derive recurrence relations for the Selberg integrals.

  8. Polymorphisms of the renin-angiotensin system genes predict progression of subclinical coronary atherosclerosis.

    PubMed

    Kretowski, Adam; McFann, Kim; Hokanson, John E; Maahs, David; Kinney, Gregory; Snell-Bergeon, Janet K; Wadwa, R Paul; Eckel, Robert H; Ogden, Lorraine; Garg, Satish; Li, Jia; Cheng, Suzanne; Erlich, Henry A; Rewers, Marian

    2007-03-01

    Premature coronary artery disease (CAD) in subjects with type 1 diabetes dramatically affects quality of life and morbidity and leads to premature death, but there is still little known about the mechanisms and predictors of this complication. In the present study, we explored the role of genetic variants of angiotensinogen (AGT, M235T), ACE (I/D), and angiotensin type 1 receptor (ATR1, A1166C) as predictors of rapid progression of subclinical coronary atherosclerosis. Five-hundred eighty-five type 1 diabetic patients and 592 similar age and sex control subjects were evaluated for progression of coronary artery calcification (CAC), a marker of subclinical CAD, before and after a 2.5-year follow-up. In logistic regression analysis, CAC progression was dramatically more likely in type 1 diabetic subjects not treated with ACE inhibitor/angiotensin receptor blocker who had the TT-ID-AA/AC genotype combination than in those with other genotypes (odds ratio 11.6 [95%CI 4.5-29.6], P < 0.0001) and was even stronger when adjusted for cardiovascular disease risk factors and the mean A1C (37.5 [3.6-388], P = 0.002). In conclusion, a combination of genotype variants of the renin-angiotensin system genes is a powerful determinant of subclinical progression of coronary artery atherosclerosis in type 1 diabetic patients and may partially explain accelerated CAD in type 1 diabetes. PMID:17327458

  9. Evaluation of Diffusion Barrier Between Lead-Free Solder Systems and Thermoelectric Materials

    NASA Astrophysics Data System (ADS)

    Lin, T. Y.; Liao, C. N.; Wu, Albert T.

    2012-01-01

    The intermetallic compound SnTe rapidly formed at interfaces between p-type bismuth telluride (Bi0.5Sb1.5Te3) thermoelectric materials and lead-free solders. The intermetallic compound influences the mechanical properties of the joints and the reliability of the thermoelectric modules. Various lead-free solder alloys, Sn-3.5Ag, Sn-3Ag-0.5Cu, Sn-0.7Cu, and Sn-2.5Ag-2Ni, were used to investigate the interfacial reactions. The results thus obtained show that Ag and Cu preferentially diffused into the Te-rich phase in Bi0.5Sb1.5Te3, so layers of Ag-Te and Cu-Te compounds could not form an effective diffusion barrier. Electroless nickel-phosphorus was plated at the interfaces to serve as a diffusion barrier, and the (Cu,Ni)6Sn5 compound formed instead of SnTe. Furthermore, the intermetallic compound NiTe formed between nickel- phosphorus and Bi0.5Sb1.5Te3 and also served as a diffusion barrier. A plot of thickness as a function of annealing time yielded the growth kinetics of the intermetallic compounds in the thermoelectric material systems. The activation energy for the growth of the NiTe intermetallic compound is 111 kJ/mol.

  10. Towards a System Level Understanding of Non-Model Organisms Sampled from the Environment: A Network Biology Approach

    PubMed Central

    Williams, Tim D.; Turan, Nil; Diab, Amer M.; Wu, Huifeng; Mackenzie, Carolynn; Bartie, Katie L.; Hrydziuszko, Olga; Lyons, Brett P.; Stentiford, Grant D.; Herbert, John M.; Abraham, Joseph K.; Katsiadaki, Ioanna; Leaver, Michael J.; Taggart, John B.; George, Stephen G.; Viant, Mark R.; Chipman, Kevin J.; Falciani, Francesco

    2011-01-01

    The acquisition and analysis of datasets including multi-level omics and physiology from non-model species, sampled from field populations, is a formidable challenge, which so far has prevented the application of systems biology approaches. If successful, these could contribute enormously to improving our understanding of how populations of living organisms adapt to environmental stressors relating to, for example, pollution and climate. Here we describe the first application of a network inference approach integrating transcriptional, metabolic and phenotypic information representative of wild populations of the European flounder fish, sampled at seven estuarine locations in northern Europe with different degrees and profiles of chemical contaminants. We identified network modules, whose activity was predictive of environmental exposure and represented a link between molecular and morphometric indices. These sub-networks represented both known and candidate novel adverse outcome pathways representative of several aspects of human liver pathophysiology such as liver hyperplasia, fibrosis, and hepatocellular carcinoma. At the molecular level these pathways were linked to TNF alpha, TGF beta, PDGF, AGT and VEGF signalling. More generally, this pioneering study has important implications as it can be applied to model molecular mechanisms of compensatory adaptation to a wide range of scenarios in wild populations. PMID:21901081

  11. Angiotensinogen Gene Silencing Reduces Markers of Lipid Accumulation and Inflammation in Cultured Adipocytes

    PubMed Central

    Carroll, Wenting X.; Kalupahana, Nishan S.; Booker, Suzanne L.; Siriwardhana, Nalin; LeMieux, Monique; Saxton, Arnold M.; Moustaid-Moussa, Naima

    2013-01-01

    Inflammatory adipokines secreted from adipose tissue are major contributors to obesity-associated inflammation and other metabolic dysfunctions. We and others have recently documented the contribution of adipose tissue renin-angiotensin system to the pathogenesis of obesity, inflammation, and insulin resistance. We hypothesized that adipocyte-derived angiotensinogen (Agt) plays a critical role in adipogenesis and/or lipogenesis as well as inflammation. This was tested using 3T3-L1 adipocytes, stably transfected with Agt-shRNA or scrambled Sc-shRNA as a control. Transfected preadipocytes were differentiated and used to investigate the role of adipose Agt through microarray and PCR analyses and adipokine profiling. As expected, Agt gene silencing significantly reduced the expression of Agt and its hormone product angiotensin II (Ang II), as well as lipid accumulation in 3T3-L1 adipocytes. Microarray studies identified several genes involved in lipid metabolism and inflammatory pathways which were down-regulated by Agt gene inactivation, such as glycerol-3-phosphate dehydrogenase 1 (Gpd1), serum amyloid A 3 (Saa3), nucleotide-binding oligomerization domain containing 1 (Nod1), and signal transducer and activator of transcription 1 (Stat1). Mouse adipogenesis PCR arrays revealed lower expression levels of adipogenic/lipogenic genes such as peroxisome proliferator activated receptor gamma (PPARγ), sterol regulatory element binding transcription factor 1 (Srebf1), adipogenin (Adig), and fatty acid binding protein 4 (Fabp4). Further, silencing of Agt gene significantly lowered expression of pro-inflammatory adipokines including interleukin-6 (IL-6), tumor necrosis factor-alpha (TNF-α), and monocyte chemotactic protein-1 (MCP-1). In conclusion, this study directly demonstrates critical effects of Agt in adipocyte metabolism and inflammation and further support a potential role for adipose Agt in the pathogenesis of obesity-associated metabolic alterations. PMID:23483012

  12. Magnetohydrodynamics (MHD) Engineering Test Facility (ETF) 200 MWe power plant. Conceptual Design Engineering Report (CDER) supplement. Magnet system special investigations

    NASA Technical Reports Server (NTRS)

    1981-01-01

    The results of magnet system special investigations listed below are summarized: 4 Tesla Magnet Alternate Design Study; 6 Tesla Magnet Manufacturability Study. The conceptual design for a 4 Tesla superconducting magnet system for use with an alternate (supersonic) ETF power train is described, and estimated schedule and cost are identified. The magnet design is scaled from the ETF 6 T Tesla design. Results of a manufacturability study and a revised schedule and cost estimate for the ETF 6 T magnet are reported. Both investigations are extensions of the conceptual design of a 6 T magnet system performed earlier as a part of the overall MED-ETF conceptual design described in Conceptual Design Engineering Report (CDER) Vol. V, System Design Description (SDD) 503 dated September, 1981, DOE/NASA/0224-1; NASA CR-165/52.

  13. Modeling of a Hybrid System for a Lightweight Electric Vehicle with Passive-type Polymer Electrolyte Fuel Cells and Electric Double-layer Capacitors

    NASA Astrophysics Data System (ADS)

    Imanishi, Hiroyuki; Yoshii, Taichi; Nakamura, Takuji; Takada, Yogo; Wakisaka, Tomoyuki

    A simple series hybrid power system composed of passive-type polymer electrolyte fuel cells (PEFCs) and electric double-layer capacitors was adapted to a lightweight electric vehicle. In order to numerically simulate the behavior of the hybrid system, a fuel cell equivalent circuit model was applied and the model parameters were determined using an electrochemical theory and experimental results. Including this PEFC equivalent circuit model, a simulation model of the power train system (PEFCs, capacitors, motor, power controller, inertia, etc) of a lightweight electric vehicle was composed. It has been confirmed that this simulation model can represent reasonably well the dynamic behavior and energy transmission of the system in the experiment on a fixed apparatus constructed as a model of the vehicle.

  14. Activation of the intrarenal renin-angiotensin-system in murine polycystic kidney disease

    PubMed Central

    Saigusa, Takamitsu; Dang, Yujing; Bunni, Marlene A; Amria, May Y; Steele, Stacy L; Fitzgibbon, Wayne R; Bell, P Darwin

    2015-01-01

    The mechanism for early hypertension in polycystic kidney disease (PKD) has not been elucidated. One potential pathway that may contribute to the elevation in blood pressure in PKD is the activation of the intrarenal renin-angiotensin-system (RAS). For example, it has been shown that kidney cyst and cystic fluid contains renin, angiotensin II (AngII), and angiotensinogen (Agt). Numerous studies suggest that ciliary dysfunction plays an important role in PKD pathogenesis. However, it is unknown whether the primary cilium affects the intrarenal RAS in PKD. The purpose of this study was to determine whether loss of cilia or polycystin 1 (PC1) increases intrarenal RAS in mouse model of PKD. Adult Ift88 and Pkd1 conditional floxed allele mice with or without cre were administered tamoxifen to induce global knockout of the gene. Three months after tamoxifen injection, kidney tissues were examined by histology, immunofluorescence, western blot, and mRNA to assess intrarenal RAS components. SV40 immortalized collecting duct cell lines from hypomorphic Ift88 mouse were used to assess intrarenal RAS components in collecting duct cells. Mice without cilia and PC1 demonstrated increased kidney cyst formation, systolic blood pressure, prorenin, and kidney and urinary angiotensinogen levels. Interestingly immunofluorescence study of the kidney revealed that the prorenin receptor was localized to the basolateral membrane of principal cells in cilia (−) but not in cilia (+) kidneys. Collecting duct cAMP responses to AngII administration was greater in cilia (−) vs. cilia (+) cells indicating enhanced intrarenal RAS activity in the absence of cilia. These data suggest that in the absence of cilia or PC1, there is an upregulation of intrarenal RAS components and activity, which may contribute to elevated blood pressure in PKD. PMID:25999403

  15. A volumetric flow sensor for automotive injection systems

    NASA Astrophysics Data System (ADS)

    Schmid, U.; Krötz, G.; Schmitt-Landsiedel, D.

    2008-04-01

    For further optimization of the automotive power train of diesel engines, advanced combustion processes require a highly flexible injection system, provided e.g. by the common rail (CR) injection technique. In the past, the feasibility to implement injection nozzle volumetric flow sensors based on the thermo-resistive measurement principle has been demonstrated up to injection pressures of 135 MPa (1350 bar). To evaluate the transient behaviour of the system-integrated flow sensors as well as an injection amount indicator used as a reference method, hydraulic simulations on the system level are performed for a CR injection system. Experimentally determined injection timings were found to be in good agreement with calculated values, especially for the novel sensing element which is directly implemented into the hydraulic system. For the first time pressure oscillations occurring after termination of the injection pulse, predicted theoretically, could be verified directly in the nozzle. In addition, the injected amount of fuel is monitored with the highest resolution ever reported in the literature.

  16. A Meta-Analysis of Periodized Versus Nonperiodized Strength and Power Training Programs

    ERIC Educational Resources Information Center

    Rhea, Matthew R.; Alderman, Brandon L.

    2004-01-01

    The purpose of this study was to quantitatively combine and examine the results of studies examining the effectiveness of periodized (PER) compared to nonperiodized (Non-PER) training programs for strength and/or power development. Two analyses were conducted to (a) examine the magnitude of treatment effect elicited by PER strength training…

  17. Comprehensive quality assurance phantom for cardiovascular imaging systems

    NASA Astrophysics Data System (ADS)

    Lin, Pei-Jan P.

    1998-07-01

    With the advent of high heat loading capacity x-ray tubes, high frequency inverter type generators, and the use of spectral shaping filters, the automatic brightness/exposure control (ABC) circuit logic employed in the new generation of angiographic imaging equipment has been significantly reprogrammed. These new angiographic imaging systems are designed to take advantage of the power train capabilities to yield higher contrast images while maintaining, or lower, the patient exposure. Since the emphasis of the imaging system design has been significantly altered, the system performance parameters one is interested and the phantoms employed for the quality assurance must also change in order to properly evaluate the imaging capability of the cardiovascular imaging systems. A quality assurance (QA) phantom has been under development in this institution and was submitted to various interested organizations such as American Association of Physicists in Medicine (AAPM), Society for Cardiac Angiography & Interventions (SCA&I), and National Electrical Manufacturers Association (NEMA) for their review and input. At the same time, in an effort to establish a unified standard phantom design for the cardiac catheterization laboratories (CCL), SCA&I and NEMA have formed a joint work group in early 1997 to develop a suitable phantom. The initial QA phantom design has since been accepted to serve as the base phantom by the SCA&I- NEMA Joint Work Group (JWG) from which a comprehensive QA Phantom is being developed.

  18. [Does a genetic predisposition for infarction expansion exist? Evaluation of genetic polymorphisms of the renin-angiotensin system].

    PubMed

    Zedda, N; Onnis, E; Angius, A; Balata, F; Cherchi, P A; Sole, G; Olla, N; Poddie, D; Cao, A; Cherchi, A; Pirastu, M

    1997-03-01

    Aim of this study is to carry out a genetic analysis of polymorphisms of the renin-angiotensin system in a genetically homogeneous population, in patients with and without myocardial infarction (AMI) expansion and to evaluate the influence of non genetic, mechanical factors. The study was conducted on 299 patients with first AMI. Ecocardiography studies were performed on all patients on day 1 and 3 from the onset of AMI and before discharge. Eighty-four patients were excluded because of inadequate quality of echocardiograms and 215 (163 males, 52 females) were admitted. Of these, 157 had no evidence of AMI expansion (EXP-) while 58 had expansion (EXP+). DNA was extracted by standard methods from blood samples. Age and gender had no influence on AMI expansion. Anterior infarction (p < 0.000001) and Q-wave infarction (p < 0.00002) were found more frequently in EXP+. Peak of creatine phosphokinase was higher in EXP+ than in EXP- (p < 0.00001). The percent of patients treated with thrombolysis or with hypertension and/or left ventricular hypertrophy was not significantly different in the two groups. AGT MT235 polymorphism of angiotensinogen gene, I/D polymorphism of ACE gene and AT1 A1166C of AT1 receptor of angiotensin II were not significantly different in two groups. Stratified analysis showed that in patients with anterior AMI (n = 87), with a higher risk of AMI expansion, there is a significant difference (p < 0.02) in ACE genotype between EXP- and EXP+. Odds ratio assuming the dominant effect of I allele (II+ ID < DD) was 3.35 (confidence interval 1.41-7.56) with increased risk of expansion. More extension studies are need to verify if these results can contribute to early identification of patients at higher risk and to optimize therapeutic approach. PMID:9172934

  19. ROCK/NF-κB axis-dependent augmentation of angiotensinogen by angiotensin II in primary-cultured preglomerular vascular smooth muscle cells

    PubMed Central

    Satou, Ryousuke; Shao, Weijian; Prieto, Minolfa C.; Urushihara, Maki; Kobori, Hiroyuki; Navar, L. Gabriel

    2014-01-01

    In angiotensin II (ANG II)-dependent hypertension, the augmented intrarenal ANG II constricts the renal microvasculature and stimulates Rho kinase (ROCK), which modulates vascular contractile responses. Rho may also stimulate angiotensinogen (AGT) expression in preglomerular vascular smooth muscle cells (VSMCs), but this has not been established. Therefore, the aims of this study were to determine the direct interactions between Rho and ANG II in regulating AGT and other renin-angiotensin system (RAS) components and to elucidate the roles of the ROCK/NF-κB axis in the ANG II-induced AGT augmentation in primary cultures of preglomerular VSMCs. We first demonstrated that these preglomerular VSMCs express renin, AGT, angiotensin-converting enzyme, and ANG II type 1 (AT1) receptors. Furthermore, incubation with ANG II (100 pmol/l for 24 h) increased AGT mRNA (1.42 ± 0.03, ratio to control) and protein (1.68 ± 0.05, ratio to control) expression levels, intracellular ANG II levels, and NF-κB activity. In contrast, the ANG II treatment did not alter AT1a and AT1b mRNA levels in the cells. Treatment with H-1152 (ROCK inhibitor, 10 nmol/l) and ROCK1 small interfering (si) RNA suppressed the ANG II-induced AGT augmentation and the upregulation and translocalization of p65 into nuclei. Functional studies showed that ROCK exerted a greater influence on afferent arteriole responses to ANG II in rats subjected to chronic ANG II infusions. These results indicate that ROCK is involved in NF-κB activation and the ROCK/NF-κB axis contributes to ANG II-induced AGT upregulation, leading to intracellular ANG II augmentation. PMID:24431199

  20. Laboratory-Model Integrated-System FARAD Thruster

    NASA Technical Reports Server (NTRS)

    Polzin, K.A.; Best, S.; Miller, R.; Rose, M.F.; Owens, T.

    2008-01-01

    . Neutral gas is injected over the face of the acceleration coil through a fast-acting valve that feeds a central distribution manifold. The thruster is designed to preionize the gas using an RF-frequency ringing signal produced by a discharging Vector Inversion Generator (VIG). The acceleration stage consists of a multiple-turn, multiple-strand spiral induction coil (see Fig. 1, left panel) and is designed for operation at discharge energies on the order of 100 J/pulse. Several different pulsed power train modules can be used to drive current through the acceleration coil. One such power train is based upon the Bernardes and Merryman circuit topology, which restricts voltage reversal on the capacitor banks and can be clamped to eliminate current reversal in the coil. A second option is a pulse-compression-ring power train (see Fig. 1, right panel), which takesa temporally broad, low current pulse and transforms it into a short, high current pulse.

  1. Similarities and differences of X and Y chromosome homologous genes, SRY and SOX3, in regulating the renin-angiotensin system promoters

    PubMed Central

    Araujo, Fabiano C.; Milsted, Amy; Watanabe, Ingrid K. M.; Del Puerto, Helen L.; Santos, Robson A. S.; Lazar, Jozef; Reis, Fernando M.

    2015-01-01

    The renin-angiotensin system (RAS) is subject to sex-specific modulation by hormones and gene products. However, sex differences in the balance between the vasoconstrictor/proliferative ACE/ANG II/AT1 axis, and the vasodilator/antiproliferative ACE2/ANG-(1–7)/MAS axis are poorly known. Data in the rat have suggested the male-specific Y-chromosome gene Sry to contribute to balance between these two axes, but why the testis-determining gene has these functions remains unknown. A combination of in silico genetic/protein comparisons, functional luciferase assays for promoters of the human RAS, and RNA-Seq profiling in rat were used to address if regulation of Sry on the RAS is conserved in the homologous X-chromosome gene, Sox3. Both SRY and SOX3 upregulated the promoter of Angiotensinogen (AGT) and downregulated the promoters of ACE2, AT2, and MAS, likely through overlapping mechanisms. The regulation by both SRY and SOX3 on the MAS promoter indicates a cis regulation through multiple SOX binding sites. The Renin (REN) promoter is upregulated by SRY and downregulated by SOX3, likely through trans and cis mechanisms, respectively. Sry transcripts are found in all analyzed male rat tissues including the kidney, while Sox3 transcripts are found only in the brain and testis, suggesting that the primary tissue for renin production (kidney) can only be regulated by SRY and not SOX3. These results suggest that SRY regulation of the RAS is partially shared with its X-chromosome homolog SOX3, but SRY gained a sex-specific control in the kidney for the rate-limiting step of the RAS, potentially resulting in male-specific blood pressure regulation. PMID:25759379

  2. Testing of Lightweight Fuel Cell Vehicles System at Low Speeds with Energy Efficiency Analysis

    NASA Astrophysics Data System (ADS)

    Mustaffa, Muhammad Rizuwan B.; Mohamed, Wan Ahmad Najmi B. Wan

    2013-12-01

    A fuel cell vehicle power train mini test bench was developed which consists of a 1 kW open cathode hydrogen fuel cell, electric motor, wheel, gearing system, DC/DC converter and vehicle control system (VCS). Energy efficiency identification and energy flow evaluation is a useful tool in identifying a detail performance of each component and sub-systems in a fuel cell vehicle system configuration. Three artificial traction loads was simulated at 30 kg, 40 kg and 50 kg force on a single wheel drive configuration. The wheel speed range reported here covers from idle to 16 km/h (low speed range) as a preliminary input in the research work frame. The test result shows that the system efficiency is 84.5 percent when the energy flow is considered from the fuel cell to the wheel and 279 watts of electrical power was produced by the fuel cell during that time. Dynamic system responses was also identified as the load increases beyond the motor traction capabilities where the losses at the converter and motor controller increased significantly as it tries to meet the motor traction power demands. This work is currently being further expanded within the work frame of developing a road-worthy fuel cell vehicle.

  3. Superfinished Surfaces for Power Transfer Systems Improvement

    NASA Technical Reports Server (NTRS)

    Niskanen, Paul; Manesh, Ali; Warren, Alford; Krantz, Timothy

    2002-01-01

    The continuous demands for high performance and lightweight power train systems resulted in requirements for higher power density gearing systems. However, increasing the load bearing capacity of the gear teeth, without increasing size, places stringent requirements upon metallurgy, dimensional control, and surface finish of the final products. In order to operate the mating parts near the upper bounds of their theoretical design envelope, manufacturing processes are required that are capable of improving the fatigue life and load bearing capacity of precision parts, while producing the required geometric accuracy. Results of the recent experimental studies indicate that the super finishing process is able to achieve these goals. This paper will review the results of our continuing evaluation of the super finish process as applied to aerospace gearing. Two separate evaluations were performed on gears to examine the effects of super finishing on resistance to both pitting and contact fatigue. For the reported experiments, both conventional and super finished test gears were simultaneously manufactured using the same process and the same heat lot of materials. This paper will also provide a brief description of the manufacturing technology used to achieve the results and will compare the results with other published data. In addition, this paper presents a couple of off-the-shelf manufacturing technologies that have been successfully used to super finish test specimens and will provide a glimpse of other emerging super finishing technologies. This is a US Army Manufacturing Technology project. The project was sponsored by the Aviation and Missiles Command (AMCOM) and was being managed and conducted by IIT Research Institute.

  4. Feasibility study for SOFC-GT hybrid locomotive power part II. System packaging and operating route simulation

    NASA Astrophysics Data System (ADS)

    Martinez, Andrew S.; Brouwer, Jacob; Samuelsen, G. Scott

    2012-09-01

    This work assesses the feasibility of Solid Oxide Fuel Cell-Gas Turbine (SOFC-GT) hybrid power systems for use as the prime mover in freight locomotives. The available space in a diesel engine-powered locomotive is compared to that required for an SOFC-GT system, inclusive of fuel processing systems necessary for the SOFC-GT. The SOFC-GT space requirement is found to be similar to current diesel engines, without consideration of the electrical balance of plant. Preliminary design of the system layout within the locomotive is carried out for illustration. Recent advances in SOFC technology and implications of future improvements are discussed as well. A previously-developed FORTRAN model of an SOFC-GT system is then augmented to simulate the kinematics and power notching of a train and its locomotives. The operation of the SOFC-GT-powered train is investigated along a representative route in Southern California, with simulations presented for diesel reformate as well as natural gas reformate and hydrogen as fuels. Operational parameters and difficulties are explored as are comparisons of expected system performance to modern diesel engines. It is found that even in the diesel case, the SOFC-GT system provides significant savings in fuel and CO2 emissions, making it an attractive option for the rail industry.

  5. 49 CFR 37.3 - Definitions.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... alterations unless they affect the usability of the building or facility. Automated guideway transit system or AGT means a fixed-guideway transit system which operates with automated (driverless) individual... transportation. Demand responsive system means any system of transporting individuals, including the provision...

  6. Report of the defense science board task force on defense nuclear agency. Final report

    SciTech Connect

    Not Available

    1993-04-01

    The Task Force recommends that: (1) DNA continue to be the DoD focal point for nuclear expertise; (2) The DNA charter be modified to provide focus for non-nuclear activities of critical importance to the DoD. It gives DNA authority to conduct technology base development for advanced conventional munitions, and become a focal point for technologies related to non- and counter-proliteration of weapon systems of mass destruction and their infrastructure (WMD); and (3) Anticipating cessation of UGETs, DNA should aggressively pursue technology development for AGT, AGT/UGT correlation and advanced computations, with emphasis on new theater scenarios, but with the ability to reconstitute for UGT resumption or AGT for large strategic threats within a year or two.

  7. Parameter Optimization and Operating Strategy of a TEG System for Railway Vehicles

    NASA Astrophysics Data System (ADS)

    Heghmanns, A.; Wilbrecht, S.; Beitelschmidt, M.; Geradts, K.

    2016-03-01

    A thermoelectric generator (TEG) system demonstrator for diesel electric locomotives with the objective of reducing the mechanical load on the thermoelectric modules (TEM) is developed and constructed to validate a one-dimensional thermo-fluid flow simulation model. The model is in good agreement with the measurements and basis for the optimization of the TEG's geometry by a genetic multi objective algorithm. The best solution has a maximum power output of approx. 2.7 kW and does not exceed the maximum back pressure of the diesel engine nor the maximum TEM hot side temperature. To maximize the reduction of the fuel consumption, an operating strategy regarding the system power output for the TEG system is developed. Finally, the potential consumption reduction in passenger and freight traffic operating modes is estimated under realistic driving conditions by means of a power train and lateral dynamics model. The fuel savings are between 0.5% and 0.7%, depending on the driving style.

  8. Bluetooth wireless monitoring, diagnosis and calibration interface for control system of fuel cell bus in Olympic demonstration

    NASA Astrophysics Data System (ADS)

    Hua, Jianfeng; Lin, Xinfan; Xu, Liangfei; Li, Jianqiu; Ouyang, Minggao

    With the worldwide deterioration of the natural environment and the fossil fuel crisis, the possible commercialization of fuel cell vehicles has become a hot topic. In July 2008, Beijing started a clean public transportation plan for the 29th Olympic games. Three fuel cell city buses and 497 other low-emission vehicles are now serving the Olympic core area and Beijing urban areas. The fuel cell buses will operate along a fixed bus line for 1 year as a public demonstration of green energy vehicles. Due to the specialized nature of fuel cell engines and electrified power-train systems, measurement, monitoring and calibration devices are indispensable. Based on the latest Bluetooth wireless technology, a novel Bluetooth universal data interface was developed for the control system of the fuel cell city bus. On this platform, a series of wireless portable control auxiliary systems have been implemented, including wireless calibration, a monitoring system and an in-system programming platform, all of which are ensuring normal operation of the fuel cell buses used in the demonstration.

  9. Sex-specific disruption of murine midbrain astrocytic and dopaminergic developmental trajectories following antenatal GC treatment.

    PubMed

    McArthur, Simon; Pienaar, Ilse S; Siddiqi, Sindhu M; Gillies, Glenda E

    2016-06-01

    The mammalian midbrain dopaminergic systems arising in the substantia nigra pars compacta (SNc) and ventral tegmental area (VTA) are critical for coping behaviours and are implicated in neuropsychiatric disorders where early life challenges comprise significant risk factors. Here, we aimed to advance our hypothesis that glucocorticoids (GCs), recognised key players in neurobiological programming, target development within these systems, with a novel focus on the astrocytic population. Mice received antenatal GC treatment (AGT) by including the synthetic GC, dexamethasone, in the mothers' drinking water on gestational days 16-19; controls received normal drinking water. Analyses of regional shapes and volumes of the adult SNc and VTA demonstrated that AGT induced long-term, dose-dependent, structural changes that were accompanied by profound effects on astrocytes (doubling/tripling of numbers and/or density). Additionally, AGT induced long-term changes in the population size and distribution of SNc/VTA dopaminergic neurons, confirming and extending our previous observations made in rats. Furthermore, glial/neuronal structural remodelling was sexually dimorphic and depended on the AGT dose and sub-region of the SNc/VTA. Investigations within the neonatal brain revealed that these long-term organisational effects of AGT depend, at least in part, on targeting perinatal processes that determine astrocyte density and programmed cell death in dopaminergic neurons. Collectively, our characterisation of enduring, AGT-induced, sex-specific cytoarchitectural disturbances suggests novel mechanistic links for the strong association between early environmental challenge (inappropriate exposure to excess GCs) and vulnerability to developing aberrant behaviours in later life, with translational implications for dopamine-associated disorders (such as schizophrenia, ADHD, autism, depression), which typically show a sex bias. PMID:25944572

  10. Irregular blocks, N = 2 gauge theory and Mathieu system

    NASA Astrophysics Data System (ADS)

    Piatek, M. R.; Pietrykowski, A. R.

    2016-01-01

    The Alday-Gayotto-Tachikawa (AGT) conjecture relates 4d N = 2, SU(2) SYM theories with Nf matter hypermultiplets to 2d CFT. In case of pure 4d N = 2, SU(2) SYM there is a corresponding irregular conformal block in 2d CFT. The AGT correspondence may be extended within a certain limit (the Nekrasov-Shataschvili limit) to the correspondence between an effective twisted superpotentials of 2d N = 2 SUSY and the Zamolodchikov's “classical” conformal blocks. When narrowed to the pure 4d N = 2 SYM case its limit is related to an irregular classical conformal block. It will be shown that according to the triple correspondence (2dCFT/Gauge/Bethe - c.f. Piatek's talk) the irregular classical conformal block yields spectrum of Mathieu operator. The latter can be obtained as a “classical” limit of the null vector decoupling equation for three-point degenerate irregular block. It will also be shown that the Mathieu spectrum can be also obtained from the limit of the pure gauge theory as a solution of the saddle point equation as well as from the Bohr-Sommerfeld quantization of the Seiberg-Witten theory.

  11. A hybrid electric propulsion system for a forest vehicle

    SciTech Connect

    Carlini, M.; Abenavoli, R.I.; Kormanski, H.; Rudzinska, K.

    1997-12-31

    Typical caterpillar tractors, applied to wood gathering in forests, are powered by internal combustion (IC) engines, which are sized to meet the full drive train load. However, the maximum power is required only in a part of the total operation time during work cycles of logging tractors. For this reason the hybrid electric propulsion system, installed instead of IC engine-hydrostatic transmission system, may considerably improve vehicle performance indices such as fuel consumption, pollutant emission and noise level. In this paper the authors present a series hybrid electric power train configuration for a small (2,100 kg of mass) crawler tractor used for logging in forests. The drive train is composed of a thermal engine, an electric generator, a group of lead-acid batteries and electric drive motors with controllers. To calculate energy balance of the designed vehicle a special forest cycle was elaborated and discussed in the paper. The cycle was created on the basis of experimental data, measured in the actual tractor work. Since average power required during the forest cycle is much lower than the maximum one, the hybrid electric system needs a smaller IC engine than one in the conventional vehicle. This engine, coupled with electric generator, works in operation conditions yielding better fuel economy. The electric drive motors are fed both by the generator and the batteries in the full load cycle phase. The batteries are recharged during vehicle down-hill moving and standing phases. The proposed hybrid electric propulsion is also an attractive approach to improve crawler tractors for agriculture applications.

  12. A highly automatic measurement system for three orthogonal magnetic moments of a permanent magnet block

    NASA Astrophysics Data System (ADS)

    Hwang, C. S.; Yeh, Shuting; Teng, P. K.; Uen, T. M.

    1996-05-01

    A highly automatic system with a three-angle rotation mechanism has been designed and constructed to measure several thousand permanent magnet blocks. The system's main features include its high speed, highly automatic measurement, and the ease with which the different size magnet blocks can be installed and removed. This system provides precise and accurate measurements of the three orthogonal magnetic moment components to accurately characterize each block, as deemed necessary to assess the field quality of undulators and wigglers. A three-angle in rotation mechanism, together with a simple mathematical algorithm is used to measure and analyze the magnetic moments of the magnet block. The system includes the Helmholtz coil pair, block holder, the three-degree rotation mechanism, and the control and data acquisition system. A power train system consists of one motor coupled with a nonmagnetic stainless steel for 360° rotation and two motors individually coupled with two groups of nonmagnetic time belts for rotation angles of 0°, 180°, 0°, and 90°. The control system uses a microcomputer together with a stepping motor control card and a digital fluxmeter connected by the general purpose interface bus. The measurement speed of this system is 40 blocks per h. One reference magnet was measured, with those results verifying the long term precision of the order of 0.04% for the easy component and 0.02° for two minor components. The coil-pair geometry factor is calibrated via the voltage-field reciprocity principle, indicating that the system absolute accuracy is around 0.43%.

  13. Process analysis of a liquid-feed direct methanol fuel cell system

    NASA Astrophysics Data System (ADS)

    Andrian, Stefanie v.; Meusinger, Josefin

    Recently, a greatly increasing interest in solid polymer electrolyte fuel cells (PEFC) for a range of applications has been observed. The direct methanol fuel cell (DMFC) based on a PEFC uses methanol directly for electric power generation and promises technical advantages, for example, for power trains. This study analyses the interaction between a DMFC stack fed with a liquid aqueous methanol solution and the peripheral system equipment. A simulation model of a DMFC system for mobile applications (from methanol to net electricity) is presented to calculate system efficiencies on the basis of thermodynamic engineering calculations. Based on the simulation calculations, useful operating requirements can be specified. To optimise the performance of DMFC systems, it is necessary to consider the operational characteristics of all the components required in the system. There are worldwide activities to improve the performance of a DMFC stack, which depends on numerous operating parameters. But it is not sufficient to optimise only the current/potential curves of the fuel cell without taking all the consequences for the system into consideration. The results of the computer simulation presented here emphasise the difficulties in improving fuel cell performance without decreasing system efficiency and describes the consequences for the system's operation conditions. Priorities are additionally set concerning the heat management of the fuel cell stack. In the case of liquid fuel supply, the water crossover through the membrane and the ensuing vapourisation at the cathode side impairs the thermal balance. Key operating parameters, which influence these effects, are pressure, temperature, air flow and methanol permeation rate.

  14. Dietary peptides from the non-digestible fraction of Phaseolus vulgaris L. decrease angiotensin II-dependent proliferation in HCT116 human colorectal cancer cells through the blockade of the renin-angiotensin system.

    PubMed

    Luna-Vital, Diego A; Liang, Katie; González de Mejía, Elvira; Loarca-Piña, Guadalupe

    2016-05-18

    This study aimed to determine the ability of peptides present in the non-digestible fraction (NDF) of common beans to decrease angiotensin II (AngII) through the blockade of RAS and its effect on the proliferation of HCT116 human colorectal cancer cells. Pure synthesized peptides GLTSK and GEGSGA and the peptide fractions (PF) of cultivars Azufrado Higuera and Bayo Madero were used. The cells were pretreated with pure peptides, PF or AGT at their IC50 or IC25 values, in comparison with the simultaneous treatment of peptides and AGT. For western blot and microscopy analysis, 100 μM and 0.5 mg mL(-1) were used for pure peptides and PF treatments, respectively. According to the ELISA tests, GLTSK and GEGSGA decreased (p < 0.05) the conversion rate of AGT to angiotensin I (AngI) by 38 and 28%, respectively. All the peptides tested reduced (p < 0.05) the conversion rate of AngI to AngII from 38 to 50%. When the cells were pretreated with both pure peptides and PF before exposure to AGT, the effectiveness inhibiting cell proliferation was higher than the simultaneous treatment suggesting their preventive effects. GLTSK and GEGSGA interacted with the catalytic site of renin, the angiotensin-I converting enzyme, and the AngII receptor, mainly through hydrogen bonds, polar, hydrophobic and cation-π interactions according to molecular docking. Through confocal microscopy, it was determined that GLTSK and GEGSGA caused the decrease (p < 0.05) of AngII-dependent STAT3 nuclear activation in HCT116 cells by 66 and 23%, respectively. The results suggest that peptides present in the common bean NDF could potentially ameliorate the effects of RAS overexpression in colorectal cancer. PMID:27156533

  15. 75 FR 11914 - Chrysler, LLC, Mack Avenue Engine Plants 1 & 2, Power Train Division, Including On-Site Leased...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-03-12

    ... Division, Detroit, Michigan. The notice was published in the Federal Register on December 18, 2008 (73 FR..., Including On-Site Leased Workers From Caravan Knight Facilities Management LLC; Detroit, MI; Amended... Jeep Grand Cherokee. New information shows that workers leased from Caravan Knight...

  16. System requirements. [Space systems

    SciTech Connect

    Austin, R.E.

    1982-06-01

    Requirements of future space systems, including large space systems, that operate beyond the space shuttle are discussed. Typical functions required of propulsion systems in this operational regime include payload placement, retrieval, observation, servicing, space debris control and support to large space systems. These functional requirements are discussed in conjunction with two classes of propulsion systems: (1) primary or orbit transfer vehicle (OTV) and (2) secondary or systems that generally operate within or relatively near an operational base orbit. Three propulsion system types are described in relation to these requirements: cryogenic OTV, teleoperator maneuvering system and a solar electric OTV.

  17. In Vivo Roles of Conjugation with Glutathione and O6-Alkylguanine DNA-Alkyltransferase in the Mutagenicity of the bis-Electrophiles 1,2-Dibromoethane and 1,2,3,4-Diepoxybutane in Mice

    PubMed Central

    Cho, Sung-Hee; Guengerich, F. Peter

    2013-01-01

    Several studies with bacteria and in vitro mammalian systems have provided evidence for the roles of two thiol-based conjugation systems, glutathione (GSH) transferase and O6-alkylguanine DNA-alkyltransferase (AGT), in the bioactivation of the bis-electrophiles 1,2-dibromoethane and 1,2,3,4-diepoxybutane (DEB), the latter an oxidation product of 1,3-butadiene. The in vivo relevance of these conjugation reactions to biological activity in mammals has not been addressed, particularly with DEB. In the present work we used transgenic Big Blue® mice, utilizing the cII gene, to examine the effects of manipulation of conjugation pathways on liver mutations arising from dibromoethane and DEB in vivo. Treatment of the mice with butathionine sulfoxime (BSO) prior to dibromoethane lowered hepatic GSH levels, dibromoethane-GSH DNA adducts (N7-guanyl), and cII mutation frequency. Administration of O6-benzylguanine (O6-BzGua), an inhibitor of AGT, did not change the mutation frequency. Depletion of GSH (BSO) and AGT (O6-BzGua) both lowered the mutation frequency induced by DEB, and BSO lowered the levels of GSH-DEB N7-guanyl and N6-adenyl DNA adducts. Our results provide evidence that the GSH conjugation pathway is a major in vivo factor in dibromoethane genotoxicity; both GSH and AGT conjugation are major factors in the genotoxicity of DEB. The latter findings are considered to be of relevance to the carcinogenicity of 1,3-butadiene. PMID:24191644

  18. In vivo roles of conjugation with glutathione and O6-alkylguanine DNA-alkyltransferase in the mutagenicity of the bis-electrophiles 1,2-dibromoethane and 1,2,3,4-diepoxybutane in mice.

    PubMed

    Cho, Sung-Hee; Guengerich, F Peter

    2013-11-18

    Several studies with bacteria and in vitro mammalian systems have provided evidence of the roles of two thiol-based conjugation systems, glutathione (GSH) transferase and O(6)-alkylguanine DNA-alkyltransferase (AGT), in the bioactivation of the bis-electrophiles 1,2-dibromoethane and 1,2,3,4-diepoxybutane (DEB), the latter an oxidation product of 1,3-butadiene. The in vivo relevance of these conjugation reactions to biological activity in mammals has not been addressed, particularly with DEB. In this work, we used transgenic Big Blue mice, utilizing the cII gene, to examine the effects of manipulation of conjugation pathways on liver mutations arising from dibromoethane and DEB in vivo. Treatment of the mice with butathionine sulfoxime (BSO) prior to dibromoethane lowered hepatic GSH levels, dibromoethane-GSH DNA adduct levels (N(7)-guanyl), and the cII mutation frequency. Administration of O(6)-benzylguanine (O(6)-BzGua), an inhibitor of AGT, did not change the mutation frequency. Depletion of GSH (BSO) and AGT (O(6)-BzGua) lowered the mutation frequency induced by DEB, and BSO lowered the levels of GSH-DEB N(7)-guanyl and N(6)-adenyl DNA adducts. Our results provide evidence that the GSH conjugation pathway is a major in vivo factor in dibromoethane genotoxicity; both GSH conjugation and AGT conjugation are major factors in the genotoxicity of DEB. The latter findings are considered to be relevant to the carcinogenicity of 1,3-butadiene. PMID:24191644

  19. Dynamic investigation of PEFC stacks in interaction with the air supply system

    NASA Astrophysics Data System (ADS)

    Philipps, F.; Simons, G.; Schiefer, K.

    This paper explores the behaviour of a dynamically operated fuel cell system regarding to an automotive application, examining the air supply and their interaction with the fuel cell stacks. The dynamic limits of stack operation are also discussed. Finally, the paper provides a description of the test facility used in these investigations. The research of dynamically operated fuel cell stacks shows that in order to achieve high energy efficiency, a power-dependent modulation of the pressure and flow rate of the air supply is necessary. A test facility designed for energy management and power train research (up to 42 kW) was used for the experiment. A number of 11.5 kW fuel cell stacks was examined experimentally with respect to performance in interaction with the air supply in stationary and dynamic operation. The stacks were tested individually and in parallel. All of them were operated "dead-end" on the hydrogen side. Experimental results varying the parameters and load curves applied to the air supply system are given in the paper. The results show different dynamic behaviours between the stacks and a substantial difference in efficiency and dynamic response of the fuel cell system operated with different strategies. The results of different operating strategies for fuel cell systems, with respect to the interaction between the fuel cell stack and the air supply and in their dependency on air mass flow and pressure level are presented. The examinations were done with the test facility using real current demand profile of the experimental car HyLite ® from zero to full load and the New European Drive Cycle (NEDC).

  20. Antenatal Glucocorticoid Treatment Induces Adaptations in Adult Midbrain Dopamine Neurons, which Underpin Sexually Dimorphic Behavioral Resilience

    PubMed Central

    Virdee, Kanwar; McArthur, Simon; Brischoux, Frédéric; Caprioli, Daniele; Ungless, Mark A; Robbins, Trevor W; Dalley, Jeffrey W; Gillies, Glenda E

    2014-01-01

    We demonstrated previously that antenatal glucocorticoid treatment (AGT, gestational days 16–19) altered the size and organization of the adult rat midbrain dopaminergic (DA) populations. Here we investigated the consequences of these AGT-induced cytoarchitectural disturbances on indices of DA function in adult rats. We show that in adulthood, enrichment of striatal DA fiber density paralleled AGT-induced increases in the numbers of midbrain DA neurons, which retained normal basal electrophysiological properties. This was co-incident with changes in (i) striatal D2-type receptor levels (increased, both sexes); (ii) D1-type receptor levels (males decreased; females increased); (iii) DA transporter levels (males increased; females decreased) in striatal regions; and (iv) amphetamine-induced mesolimbic DA release (males increased; females decreased). However, despite these profound, sexually dimorphic changes in markers of DA neurotransmission, in-utero glucocorticoid overexposure had a modest or no effect on a range of conditioned and unconditioned appetitive behaviors known to depend on mesolimbic DA activity. These findings provide empirical evidence for enduring AGT-induced adaptive mechanisms within the midbrain DA circuitry, which preserve some, but not all, functions, thereby casting further light on the vulnerability of these systems to environmental perturbations. Furthermore, they demonstrate these effects are achieved by different, often opponent, adaptive mechanisms in males and females, with translational implications for sex biases commonly found in midbrain DA-associated disorders. PMID:23929547

  1. Bandwidth based methodology for designing a hybrid energy storage system for a series hybrid electric vehicle with limited all electric mode

    NASA Astrophysics Data System (ADS)

    Shahverdi, Masood

    The cost and fuel economy of hybrid electrical vehicles (HEVs) are significantly dependent on the power-train energy storage system (ESS). A series HEV with a minimal all-electric mode (AEM) permits minimizing the size and cost of the ESS. This manuscript, pursuing the minimal size tactic, introduces a bandwidth based methodology for designing an efficient ESS. First, for a mid-size reference vehicle, a parametric study is carried out over various minimal-size ESSs, both hybrid (HESS) and non-hybrid (ESS), for finding the highest fuel economy. The results show that a specific type of high power battery with 4.5 kWh capacity can be selected as the winning candidate to study for further minimization. In a second study, following the twin goals of maximizing Fuel Economy (FE) and improving consumer acceptance, a sports car class Series-HEV (SHEV) was considered as a potential application which requires even more ESS minimization. The challenge with this vehicle is to reduce the ESS size compared to 4.5 kWh, because the available space allocation is only one fourth of the allowed battery size in the mid-size study by volume. Therefore, an advanced bandwidth-based controller is developed that allows a hybridized Subaru BRZ model to be realized with a light ESS. The result allows a SHEV to be realized with 1.13 kWh ESS capacity. In a third study, the objective is to find optimum SHEV designs with minimal AEM assumption which cover the design space between the fuel economies in the mid-size car study and the sports car study. Maximizing FE while minimizing ESS cost is more aligned with customer acceptance in the current state of market. The techniques applied to manage the power flow between energy sources of the power-train significantly affect the results of this optimization. A Pareto Frontier, including ESS cost and FE, for a SHEV with limited AEM, is introduced using an advanced bandwidth-based control strategy teamed up with duty ratio control. This controller

  2. Cys18-Cys137 disulfide bond in mouse angiotensinogen does not affect AngII-dependent functions in vivo.

    PubMed

    Wu, Congqing; Xu, Yinchuan; Lu, Hong; Howatt, Deborah A; Balakrishnan, Anju; Moorleghen, Jessica J; Vander Kooi, Craig W; Cassis, Lisa A; Wang, Jian-an; Daugherty, Alan

    2015-04-01

    Renin cleavage of angiotensinogen (AGT) releases angiotensin I (AngI) in the initial step of producing all angiotensin peptides. It has been suggested recently that redox regulation of a disulfide bond in AGT involving Cys18-Cys137 may be important to its renin cleavage efficiency in vivo. The purpose of this study was to test this prediction in a mouse model by comparing AngII production and AngII-dependent functions in mice expressing wild-type AGT versus a mutated form of AGT lacking the disulfide bond. Wild-type (hepAGT+/+) and hepatocyte-specific AGT-deficient (hepAGT-/-) littermates were developed in an low-density lipoprotein receptor -/- background. hepAGT+/+ mice were injected intraperitoneally with adeno-associated viral (AAV) vector containing a null insert. hepAGT-/- mice were injected with AAV containing a null insert, wild-type AGT or Cys18Ser and Cys137Ser mutated AGT. Two weeks after AAV injection, mice were fed a Western diet for 12 weeks. Administration of AAV containing either form of AGT led to similar plasma AGT concentrations in hepAGT-/- mice. High plasma renin concentrations in hepAGT-/- mice were suppressed equally by both forms of AGT, which were accompanied by comparable increases of plasma AngII concentrations similar to hepAGT+/+ mice. AAV-driven expression of both forms of AGT led to equivalent increases of systolic blood pressure and augmentation of atherosclerotic lesion size in hepAGT-/- mice. These measurements were comparable to systolic blood pressure and atherosclerotic lesions in hepAGT+/+ mice. These data indicate that the Cys18-Cys137 disulfide bond in AGT is dispensable for AngII production and AngII-dependent functions in mice. PMID:25691624

  3. Solar system positioning system

    NASA Technical Reports Server (NTRS)

    Penanen, Konstantin I.; Chui, Talso

    2006-01-01

    Power-rich spacecraft envisioned in Prometheus initiative open up possibilities for long-range high-rate communication. A constellation of spacecraft on orbits several A.U. from the Sun, equipped with laser transponders and precise clocks can be configured to measure their mutual distances to within few cm. High on-board power can create substantial non-inertial contribution to the spacecraft trajectory. We propose to alleviate this contribution by employing secondary ranging to a passive daughter spacecraft. Such constellation can form the basis of it navigation system capable of providing position information anywhere in the soIar system with similar accuracy. Apart from obvious Solar System exploration implications, this system can provide robust reference for GPS and its successors.

  4. Systems autonomy

    NASA Technical Reports Server (NTRS)

    Lum, Henry, Jr.

    1988-01-01

    Information on systems autonomy is given in viewgraph form. Information is given on space systems integration, intelligent autonomous systems, automated systems for in-flight mission operations, the Systems Autonomy Demonstration Project on the Space Station Thermal Control System, the architecture of an autonomous intelligent system, artificial intelligence research issues, machine learning, and real-time image processing.

  5. Immune System

    MedlinePlus

    ... How Can I Help a Friend Who Cuts? Immune System KidsHealth > For Teens > Immune System Print A A ... could put us out of commission. What the Immune System Does The immune (pronounced: ih-MYOON) system, which ...

  6. Systems Thinking (and Systems Doing).

    ERIC Educational Resources Information Center

    Brethower, Dale M.; Dams, Peter-Cornelius

    1999-01-01

    Introduces human performance technology (HPT) by answering the following questions related to: what systems does; practical issues and questions to which systems thinking is relevant; research questions and answers with respect to systems thinking; how HPT practitioners can do systems thinking; systems thinking tools; what is and is not known…

  7. 5 CFR 532.313 - Private sector industries.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... Specialized Industry 332912 Fluid power valve and hose fitting manufacturing. 336411 Aircraft manufacturing...) manufacturing. Artillery and Combat Vehicles Specialized Industry 2211 Electric power generation, transmission... vehicle brake system manufacturing. 33635 Motor vehicle transmission and power train parts...

  8. Resistin Induces Hypertension and Insulin Resistance in Mice via a TLR4-Dependent Pathway.

    PubMed

    Jiang, Yun; Lu, Linfang; Hu, Youtao; Li, Qiang; An, Chaoqiang; Yu, Xiaolan; Shu, Le; Chen, Ao; Niu, Congcong; Zhou, Lei; Yang, Zaiqing

    2016-01-01

    Resistin, an adipokine involved in insulin resistance (IR) and diabetes, has recently been reported to play a role in cardiovascular events. However, its effect on blood pressure (BP) and the underlying mechanisms remain unclear. In the present study, we showed that resistin induces hypertension and IR in wild type (WT) mice, but not in tlr4(-/-) mice. Resistin upregulated angiotensinogen (Agt) expression in WT mice, whereas it had no effect on tlr4(-/-) mice, or in mice treated with the angiotensin-converting enzyme inhibitor perindopril. Real-time PCR and chromatin immunoprecipitation further confirmed that resistin activates the renin-angiotensin system (RAS) via the TLR4/P65/Agt pathway. This finding suggested an essential role of resistin in linking IR and hypertension, which may offer a novel target in clinic on the study of the association between diabetes and hypertension. PMID:26917360

  9. Resistin Induces Hypertension and Insulin Resistance in Mice via a TLR4-Dependent Pathway

    PubMed Central

    Jiang, Yun; Lu, Linfang; Hu, Youtao; Li, Qiang; An, Chaoqiang; Yu, Xiaolan; Shu, Le; Chen, Ao; Niu, Congcong; Zhou, Lei; Yang, Zaiqing

    2016-01-01

    Resistin, an adipokine involved in insulin resistance (IR) and diabetes, has recently been reported to play a role in cardiovascular events. However, its effect on blood pressure (BP) and the underlying mechanisms remain unclear. In the present study, we showed that resistin induces hypertension and IR in wild type (WT) mice, but not in tlr4−/− mice. Resistin upregulated angiotensinogen (Agt) expression in WT mice, whereas it had no effect on tlr4−/− mice, or in mice treated with the angiotensin-converting enzyme inhibitor perindopril. Real-time PCR and chromatin immunoprecipitation further confirmed that resistin activates the renin-angiotensin system (RAS) via the TLR4/P65/Agt pathway. This finding suggested an essential role of resistin in linking IR and hypertension, which may offer a novel target in clinic on the study of the association between diabetes and hypertension. PMID:26917360

  10. Crystal Systems.

    ERIC Educational Resources Information Center

    Schomaker, Verner; Lingafelter, E. C.

    1985-01-01

    Discusses characteristics of crystal systems, comparing (in table format) crystal systems with lattice types, number of restrictions, nature of the restrictions, and other lattices that can accidently show the same metrical symmetry. (JN)

  11. Concentrator Systems

    NASA Astrophysics Data System (ADS)

    Luque-Heredia, Ignacio; Luque, Antonio

    2015-10-01

    The following sections are included: * Introduction * The early development of CPV * Concentrator solar cells * Optics for photovoltaic concentrators * Photovoltaic concentration modules * Tracking systems for photovoltaic concentration * High-concentration systems * Rating and performance * Cost considerations * Conclusions * References

  12. Discovery Systems

    NASA Technical Reports Server (NTRS)

    Pell, Barney

    2003-01-01

    A viewgraph presentation on NASA's Discovery Systems Project is given. The topics of discussion include: 1) NASA's Computing Information and Communications Technology Program; 2) Discovery Systems Program; and 3) Ideas for Information Integration Using the Web.

  13. Fluid Management System (FMS) fluid systems overview

    NASA Technical Reports Server (NTRS)

    Baird, R. S.

    1990-01-01

    Viewgraphs on fluid management system (FMS) fluid systems overview are presented. Topics addressed include: fluid management system description including system requirements (integrated nitrogen system, integrated water system, and integrated waste gas system) and physical description; and fluid management system evolution.

  14. The two-mass flywheel - a torsional vibration damper for the power train of passenger cars - state-of-the-art and further technical development

    SciTech Connect

    Sebulke, A.

    1987-01-01

    The rotational irregularities of an engine, which are primarily caused by the forces generated by the combustion gases during the periodic combustion process, are transmitted to the driveline and there lead to vibration and noise. Since 1985, BMW has been using its two-mass flywheel on certain gasoline and diesel engines. This is a mechanical low-pass filter, which largely isolates rotational irregularities and vibration from the complete driveline and therefore reduces the noise level inside the vehicle. Running speeds significantly exceeding 5000 rpm however cause a severe increase in wear on the internal components of the torsional vibration damper, as a consequence of the higher centrifugal forces.

  15. Linked Systems.

    ERIC Educational Resources Information Center

    Association of Research Libraries, Washington, DC.

    Three papers are compiled here for research library directors: (1) "Background: Open Systems Interconnection," in which David F. Bishop provides fundamental background information to explain the concept of the emerging technology of linked systems and open systems interconnection--i.e., an agreed upon standard set of conventions or rules that,…

  16. Systems Engineering

    NASA Technical Reports Server (NTRS)

    Pellerano, Fernando

    2015-01-01

    This short course provides information on what systems engineering is and how the systems engineer guides requirements, interfaces with the discipline leads, and resolves technical issues. There are many system-wide issues that either impact or are impacted by the thermal subsystem. This course will introduce these issues and illustrate them with real life examples.

  17. Expert systems and fuzzy systems

    SciTech Connect

    Negoita, C.

    1985-01-01

    This book examines the design of the expert computer system and how fuzzy systems can be used to deal with imprecise information. As the author explores the effects of semantic systems on decision support systems, he asserts that the utilization of fuzzy set theory can help an expert system draw from its knowledge base more efficiently and therefore make more accurate and reliable decisions. The book includes realistic status reports in approximate reasoning and knowledge representation that are supported by a ''theory of categories'' mathematical approach. The differences between symbolic and semantic manipulation are outline, and detailed information is given on the actual theory of knowledge-based systems.

  18. System Effectiveness

    SciTech Connect

    Powell, Danny H; Elwood Jr, Robert H

    2011-01-01

    An effective risk assessment system is needed to address the threat posed by an active or passive insider who, acting alone or in collusion, could attempt diversion or theft of nuclear material. It is critical that a nuclear facility conduct a thorough self-assessment of the material protection, control, and accountability (MPC&A) system to evaluate system effectiveness. Self-assessment involves vulnerability analysis and performance testing of the MPC&A system. The process should lead to confirmation that mitigating features of the system effectively minimize the threat, or it could lead to the conclusion that system improvements or upgrades are necessary to achieve acceptable protection against the threat. Analysis of the MPC&A system is necessary to understand the limits and vulnerabilities of the system to internal threats. Self-assessment helps the facility be prepared to respond to internal threats and reduce the risk of theft or diversion of nuclear material. MSET is a self-assessment or inspection tool utilizing probabilistic risk assessment (PRA) methodology to calculate the system effectiveness of a nuclear facility's MPC&A system. MSET analyzes the effectiveness of an MPC&A system based on defined performance metrics for MPC&A functions based on U.S. and international best practices and regulations. A facility's MC&A system can be evaluated at a point in time and reevaluated after upgrades are implemented or after other system changes occur. The total system or specific subareas within the system can be evaluated. Areas of potential performance improvement or system upgrade can be assessed to determine where the most beneficial and cost-effective improvements should be made. Analyses of risk importance factors show that sustainability is essential for optimal performance. The analyses reveal where performance degradation has the greatest detrimental impact on total system risk and where performance improvements have the greatest reduction in system risk

  19. Communication: Towards first principles theory of relaxation in supercooled liquids formulated in terms of cooperative motion.

    PubMed

    Freed, Karl F

    2014-10-14

    A general theory of the long time, low temperature dynamics of glass-forming fluids remains elusive despite the almost 20 years since the famous pronouncement by the Nobel Laureate P. W. Anderson, "The deepest and most interesting unsolved problem in solid state theory is probably the theory of the nature of glass and the glass transition" [Science 267, 1615 (1995)]. While recent work indicates that Adam-Gibbs theory (AGT) provides a framework for computing the structural relaxation time of supercooled fluids and for analyzing the properties of the cooperatively rearranging dynamical strings observed in low temperature molecular dynamics simulations, the heuristic nature of AGT has impeded general acceptance due to the lack of a first principles derivation [G. Adam and J. H. Gibbs, J. Chem. Phys. 43, 139 (1965)]. This deficiency is rectified here by a statistical mechanical derivation of AGT that uses transition state theory and the assumption that the transition state is composed of elementary excitations of a string-like form. The strings are assumed to form in equilibrium with the mobile particles in the fluid. Hence, transition state theory requires the strings to be in mutual equilibrium and thus to have the size distribution of a self-assembling system, in accord with the simulations and analyses of Douglas and co-workers. The average relaxation rate is computed as a grand canonical ensemble average over all string sizes, and use of the previously determined relation between configurational entropy and the average cluster size in several model equilibrium self-associating systems produces the AGT expression in a manner enabling further extensions and more fundamental tests of the assumptions. PMID:25318708

  20. Communication: Towards first principles theory of relaxation in supercooled liquids formulated in terms of cooperative motion

    NASA Astrophysics Data System (ADS)

    Freed, Karl F.

    2014-10-01

    A general theory of the long time, low temperature dynamics of glass-forming fluids remains elusive despite the almost 20 years since the famous pronouncement by the Nobel Laureate P. W. Anderson, "The deepest and most interesting unsolved problem in solid state theory is probably the theory of the nature of glass and the glass transition" [Science 267, 1615 (1995)]. While recent work indicates that Adam-Gibbs theory (AGT) provides a framework for computing the structural relaxation time of supercooled fluids and for analyzing the properties of the cooperatively rearranging dynamical strings observed in low temperature molecular dynamics simulations, the heuristic nature of AGT has impeded general acceptance due to the lack of a first principles derivation [G. Adam and J. H. Gibbs, J. Chem. Phys. 43, 139 (1965)]. This deficiency is rectified here by a statistical mechanical derivation of AGT that uses transition state theory and the assumption that the transition state is composed of elementary excitations of a string-like form. The strings are assumed to form in equilibrium with the mobile particles in the fluid. Hence, transition state theory requires the strings to be in mutual equilibrium and thus to have the size distribution of a self-assembling system, in accord with the simulations and analyses of Douglas and co-workers. The average relaxation rate is computed as a grand canonical ensemble average over all string sizes, and use of the previously determined relation between configurational entropy and the average cluster size in several model equilibrium self-associating systems produces the AGT expression in a manner enabling further extensions and more fundamental tests of the assumptions.

  1. Communication: Towards first principles theory of relaxation in supercooled liquids formulated in terms of cooperative motion

    SciTech Connect

    Freed, Karl F.

    2014-10-14

    A general theory of the long time, low temperature dynamics of glass-forming fluids remains elusive despite the almost 20 years since the famous pronouncement by the Nobel Laureate P. W. Anderson, “The deepest and most interesting unsolved problem in solid state theory is probably the theory of the nature of glass and the glass transition” [Science 267, 1615 (1995)]. While recent work indicates that Adam-Gibbs theory (AGT) provides a framework for computing the structural relaxation time of supercooled fluids and for analyzing the properties of the cooperatively rearranging dynamical strings observed in low temperature molecular dynamics simulations, the heuristic nature of AGT has impeded general acceptance due to the lack of a first principles derivation [G. Adam and J. H. Gibbs, J. Chem. Phys. 43, 139 (1965)]. This deficiency is rectified here by a statistical mechanical derivation of AGT that uses transition state theory and the assumption that the transition state is composed of elementary excitations of a string-like form. The strings are assumed to form in equilibrium with the mobile particles in the fluid. Hence, transition state theory requires the strings to be in mutual equilibrium and thus to have the size distribution of a self-assembling system, in accord with the simulations and analyses of Douglas and co-workers. The average relaxation rate is computed as a grand canonical ensemble average over all string sizes, and use of the previously determined relation between configurational entropy and the average cluster size in several model equilibrium self-associating systems produces the AGT expression in a manner enabling further extensions and more fundamental tests of the assumptions.

  2. Cryogenic Systems

    NASA Astrophysics Data System (ADS)

    Hosoyama, Kenji

    2002-02-01

    In this lecture we discuss the principle of method of cooling to a very low temperature, i.e. cryogenic. The "gas molecular model" will be introduced to explain the mechanism cooling by the expansion engine and the Joule-Thomson expansion valve. These two expansion processes are normally used in helium refrigeration systems to cool the process gas to cryogenic temperature. The reverse Carnot cycle will be discussed in detail as an ideal refrigeration cycle. First the fundamental process of liquefaction and refrigeration cycles will be discussed, and then the practical helium refrigeration system. The process flow of the system and the key components; -compressor, expander, and heat exchanger- will be discussed. As an example of an actual refrigeration system, we will use the cryogenic system for the KEKB superconducting RF cavity. We will also discuss the liquid helium distribution system, which is very important, especially for the cryogenic systems used in accelerator applications. 1 Principles of Cooling and Fundamental Cooling Cycle 2 Expansion engine, Joule-Thomson expansion, kinetic molecular theory, and enthalpy 3 Liquefaction Systems 4 Refrigeration Systems 5 Practical helium liquefier/refrigeration system 6 Cryogenic System for TRISTAN Superconducting RF Cavity

  3. Geothermal systems

    NASA Technical Reports Server (NTRS)

    Mohl, C.

    1978-01-01

    Several tasks of JPL related to geothermal energy are discussed. The major task is the procurement and test and evaluation of a helical screw drive (wellhead unit). A general review of geothermal energy systems is given. The presentation focuses attention on geothermal reservoirs in California, with graphs and charts to support the discussion. Included are discussions on cost analysis, systems maintenance, and a comparison of geothermal and conventional heating and cooling systems.

  4. [Information systems].

    PubMed

    Rodríguez Maniega, José Antonio; Trío Maseda, Reyes

    2005-03-01

    The arrival of victims of the terrorist attacks of 11 March at the hospital put the efficiency of its information systems to the test. To be most efficient, these systems should be simple and directed, above all, to the follow-up of victims and to providing the necessary information to patients and families. A specific and easy to use system is advisable. PMID:15771852

  5. Systemic darwinism.

    PubMed

    Winther, Rasmus Grønfeldt

    2008-08-19

    Darwin's 19th century evolutionary theory of descent with modification through natural selection opened up a multidimensional and integrative conceptual space for biology. We explore three dimensions of this space: explanatory pattern, levels of selection, and degree of difference among units of the same type. Each dimension is defined by a respective pair of poles: law and narrative explanation, organismic and hierarchical selection, and variational and essentialist thinking. As a consequence of conceptual debates in the 20th century biological sciences, the poles of each pair came to be seen as mutually exclusive opposites. A significant amount of 21st century research focuses on systems (e.g., genomic, cellular, organismic, and ecological/global). Systemic Darwinism is emerging in this context. It follows a "compositional paradigm" according to which complex systems and their hierarchical networks of parts are the focus of biological investigation. Through the investigation of systems, Systemic Darwinism promises to reintegrate each dimension of Darwin's original logical space. Moreover, this ideally and potentially unified theory of biological ontology coordinates and integrates a plurality of mathematical biological theories (e.g., self-organization/structure, cladistics/history, and evolutionary genetics/function). Integrative Systemic Darwinism requires communal articulation from a plurality of perspectives. Although it is more general than these, it draws on previous advances in Systems Theory, Systems Biology, and Hierarchy Theory. Systemic Darwinism would greatly further bioengineering research and would provide a significantly deeper and more critical understanding of biological reality. PMID:18697926

  6. Anticipatory systems as linguistic systems

    NASA Astrophysics Data System (ADS)

    Ekdahl, Bertil

    2000-05-01

    The idea of system is well established although not well defined. What makes up a system depends on the observer. Thinking in terms of systems is only a convenient way to conceptualize organizations, natural or artificial, that show coherent properties. Among all properties, which can be ascribed to systems, one property seems to be more outstanding than others, namely that of being anticipatory. In nature, anticipatory properties are found only in living organizations. In this way it can be said to separate non-living systems from living because there is no indication that any natural phenomenon occurring in systems where there is no indication of life is anticipatory. The characteristic of living systems is that they are exposed to the evolution contrary to causal systems that do not undergo changes due to the influence of the environment. Causal systems are related to the past in such a way that subsequent situations can be calculated from knowledge of past situations. In causal systems the past is the cause of the present and there is no reference to the future as a determining agent, contrary to anticipatory systems where expectations are the cause of the present action. Since anticipatory properties are characteristic of living systems, this property, as all other properties in living systems, is a result of the evolution and can be found in plants as well as in animals. Thus, it is not only tied to consciousness but is found at a more basic level, i.e., in the interplay between genotype and phenotype. Anticipation is part of the genetic language in such a way that appropriate actions, for events in the anticipatory systems environment, are inscribed in the genes. Anticipatory behavior, as a result of the interpretation of the genetic language, has been selected by the evolution. In this paper anticipatory systems are regarded as linguistic systems and I argue that as such anticipation cannot be fragmented but must be holistically studied. This has the

  7. Combustor development for automotive gas turbines

    SciTech Connect

    Ross, P.T.; Anderson, D.N.; Williams, J.R.

    1983-09-01

    This paper describes the development of a combustion system for the AGT 100 automotive gas turbine engine. The AGT 100 is a 100 hp engine being developed by Detroit Diesel Allison Division of General Motors Corporation. To achieve optimum fuel economy, the AGT 100 engine operates on a regenerative cycle. A maximum turbine inlet temperature of 1288/sup 0/C (2350/sup 0/F) is reached, and air is supplied to the inlet of the combustor at temperatures as high as 1024/sup 0/C (1875/sup 0/F). To meet the low-emission and high-durability requirements at these conditions, a premix/prevaporization ceramic combustor employing variable geometry to control the temperature in the burning zone has been developed. A test section capable of handling 1024/sup 0/C (1875/sup 0/F) inlet air was designed and fabricated to evaluate this combustor. Testing of both metal (transpiration cooled) and ceramic combustors was conducted. Emissions were measured and found to be a function of burner inlet temperature. At 999/sup 0/C (1830/sup 0/F) burner inlet temperature, NO /SUB x/ emissions were two orders of magnitude below the program goals. At the same temperature but at a different variable-geometry position, the CO was 30 times below the program goal. Considerable testing was conducted to evaluate the behavior of the ceramic materials used in the combustor. No failures occurred during steady-state operation; however, some cracks developed in the dome during extended transient operation.

  8. Educational Systems.

    ERIC Educational Resources Information Center

    Archer, Margaret

    1981-01-01

    Presents a general review of research on educational systems, with emphasis on variations in the definition of an educational system, neglected questions, areas of major concern, research needs, traditional and modern stands in the sociology of education, educational politics, and researcher bias. (DB)

  9. Systemic Change.

    ERIC Educational Resources Information Center

    Tosti, Donald T.

    2000-01-01

    Examines three factors contributing to organizational success: use of a systemic model to design and guide the change effort; analysis of interdependencies within the system and of the change potential; and use of communication methods to help ensure that the change will be supported. Presents characteristics of successful change efforts with…

  10. Power system

    DOEpatents

    Hickam, Christopher Dale

    2008-03-18

    A power system includes a prime mover, a transmission, and a fluid coupler having a selectively engageable lockup clutch. The fluid coupler may be drivingly connected between the prime mover and the transmission. Additionally, the power system may include a motor/generator drivingly connected to at least one of the prime mover and the transmission. The power-system may also include power-system controls configured to execute a control method. The control method may include selecting one of a plurality of modes of operation of the power system. Additionally, the control method may include controlling the operating state of the lockup clutch dependent upon the mode of operation selected. The control method may also include controlling the operating state of the motor/generator dependent upon the mode of operation selected.

  11. Electronic system

    DOEpatents

    Robison, G H; Dickson, J F

    1960-11-15

    An electronic system is designed for indicating the occurrence of a plurality of electrically detectable events within predetermined time intervals. The system comprises separate input means electrically associated with the events under observation an electronic channel associated with each input means, including control means and indicating means; timing means adapted to apply a signal from the input means after a predetermined time to the control means to deactivate each of the channels; and means for resetting the system to its initial condition after the observation of each group of events. (D.L.C.)

  12. System identification

    NASA Astrophysics Data System (ADS)

    Juang, Jer-Nan

    Major issues in system identification are summarized and recent advances are reviewed. Modal testing and system identification used in control theory are examined, and the mathematical relationships and conversions of the models appropriate to modal testing and those appropriate to modern control design methods are discussed. The importance of obtaining input and output matrices in modal testing is emphasized, and the changes that may be needed in modal testing procedures to meet the needs of the control system designer are addressed. Directions for future research are considered.

  13. Saturn Systems.

    PubMed

    U Rehman, Habib; McKee, Nida A; McKee, Michael L

    2016-01-15

    Several ring systems (Saturn systems) have been studied using DFT methods that include dispersion effects. Comparison with X-ray structures are made with three systems, and the agreement is quite good. Binding enthalpies and binding free energies in dichloromethane and toluene have been computed. The effect of an encapsulated lithium cation is accessed by comparing C60 @(C6 H4 )10 and [Li@C60 @(C6 H4 )10 ](+). The [Li@C60 ](+) cation is a much better acceptor than C60 which leads to greater donor-acceptor interactions and larger charge transfer from the ring to [Li@C60 ](+). PMID:26096724

  14. Processing system

    NASA Technical Reports Server (NTRS)

    Hilland, J. E.

    1983-01-01

    To implement the analysis techniques and to provide end-to-end processing, a system was designed with the following capabilities: receive and catalog data from many sources; organize the data on mass storage for rapid access; edit for reasonableness; create new data sets by sorting on parameter, averaging and merging; provide statistical analysis and display tools; and distribute data on demand. Consideration was given to developing a flexible system that could meet immediate workshop needs and respond to future requirements. System architecture and data set details implemented are discussed.

  15. Respiratory system

    NASA Technical Reports Server (NTRS)

    Bartlett, R. G., Jr.

    1973-01-01

    The general anatomy and function of the human respiratory system is summarized. Breathing movements, control of breathing, lung volumes and capacities, mechanical relations, and factors relevant to respiratory support and equipment design are discussed.

  16. Microelectromechanical Systems

    NASA Technical Reports Server (NTRS)

    Gabriel, Kaigham J.

    1995-01-01

    Micro-electromechanical systems (MEMS) is an enabling technology that merges computation and communication with sensing and actuation to change the way people and machines interact with the physical world. MEMS is a manufacturing technology that will impact widespread applications including: miniature inertial measurement measurement units for competent munitions and personal navigation; distributed unattended sensors; mass data storage devices; miniature analytical instruments; embedded pressure sensors; non-invasive biomedical sensors; fiber-optics components and networks; distributed aerodynamic control; and on-demand structural strength. The long term goal of ARPA's MEMS program is to merge information processing with sensing and actuation to realize new systems and strategies for both perceiving and controlling systems, processes, and the environment. The MEMS program has three major thrusts: advanced devices and processes, system design, and infrastructure.

  17. Lymph system

    MedlinePlus

    ... the lymph nodes make more infection-fighting white blood cells, which cause the nodes to swell. The swollen nodes are sometimes felt in the neck, under the arms, and groin. The lymph system includes the: Tonsils Adenoids Spleen Thymus

  18. [Systemic urticarias].

    PubMed

    Hachulla, E

    2003-05-01

    Systemic urticaria remains a challenge in terms of etiology, investigation and management. Most of cases are urticarial vasculitis consequence of inflammatory injury of capillaries and postcapillary venules in the skin. If hypocomplementemic urticarial vasculitis syndrome is a classical cause, the majority of patients have an underlying systemic disease like systemic lupus erythematosus, Sjögren's syndrome, mixed cryoglobulinemia, Still disease or cancer. Others systemic urticaria have been reported without clearly evidence of vasculitis like in primary or acquired angioedema, hereditary periodic fever syndromes and in some thyroiditis. Diagnosis needs a step to step procedure. Treatment depends the underlying disease. Some patients respond to nonsteroidal antiinflammatory drugs, some other need corticosteroids or immunosuppression. If urticarial vasculitis seems isolated in the absence of chronic obstructive pulmonary disease, antihistamines, nonsteroidal antiinflammatory drugs, colchicine, dapsone or hydroxychloroquine must be first used. PMID:12843810

  19. SAMPLING SYSTEM

    DOEpatents

    Hannaford, B.A.; Rosenberg, R.; Segaser, C.L.; Terry, C.L.

    1961-01-17

    An apparatus is given for the batch sampling of radioactive liquids such as slurries from a system by remote control, while providing shielding for protection of operating personnel from the harmful effects of radiation.

  20. Recommender systems

    NASA Astrophysics Data System (ADS)

    Lü, Linyuan; Medo, Matúš; Yeung, Chi Ho; Zhang, Yi-Cheng; Zhang, Zi-Ke; Zhou, Tao

    2012-10-01

    The ongoing rapid expansion of the Internet greatly increases the necessity of effective recommender systems for filtering the abundant information. Extensive research for recommender systems is conducted by a broad range of communities including social and computer scientists, physicists, and interdisciplinary researchers. Despite substantial theoretical and practical achievements, unification and comparison of different approaches are lacking, which impedes further advances. In this article, we review recent developments in recommender systems and discuss the major challenges. We compare and evaluate available algorithms and examine their roles in the future developments. In addition to algorithms, physical aspects are described to illustrate macroscopic behavior of recommender systems. Potential impacts and future directions are discussed. We emphasize that recommendation has great scientific depth and combines diverse research fields which makes it interesting for physicists as well as interdisciplinary researchers.

  1. Systems and Components Fuel Delivery System, Water Delivery System, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Systems and Components - Fuel Delivery System, Water Delivery System, Derrick Crane System, and Crane System Details - Marshall Space Flight Center, F-1 Engine Static Test Stand, On Route 565 between Huntsville and Decatur, Huntsville, Madison County, AL

  2. Scaling and Systems Considerations in Pulsed Inductive Thrusters

    NASA Technical Reports Server (NTRS)

    Polzin, Kurt A.

    2007-01-01

    Performance scaling in pulsed inductive thrusters is discussed in the context of previous experimental studies and modeling results. Two processes, propellant ionization and acceleration, are interconnected where overall thruster performance and operation are concerned, but they are separated here to gain physical insight into each process and arrive at quantitative criteria that should be met to address or mitigate inherent inductive thruster difficulties. The effects of preionization in lowering the discharge energy requirements relative to a case where no preionization is employed, and in influencing the location of the initial current sheet, are described. The relevant performance scaling parameters for the acceleration stage are reviewed, emphasizing their physical importance and the numerical values required for efficient acceleration. The scaling parameters are then related to the design of the pulsed power train providing current to the acceleration stage. The impact of various choices in pulsed power train and circuit topology selection are reviewed, paying special attention to how these choices mitigate or exacerbate switching, lifetime, and power consumption issues.

  3. Systems Studies

    SciTech Connect

    Graham, R.L.

    1998-03-17

    The Systems Studies Activity had two objectives: (1) to investigate nontechnical barriers to the deployment of biomass production and supply systems and (2) to enhance and extend existing systems models of bioenergy supply and use. For the first objective, the Activity focused on existing bioenergy markets. Four projects were undertaken: a comparative analysis of bioenergy in Sweden and Austria; a one-day workshop on nontechnical barriers jointly supported by the Production Systems Activity; the development and testing of a framework for analyzing barriers and drivers to bioenergy markets; and surveys of wood pellet users in Sweden, Austria and the US. For the second objective, two projects were undertaken. First, the Activity worked with the Integrated BioEnergy Systems (TBS) Activity of TEA Bioenergy Task XIII to enhance the BioEnergy Assessment Model (BEAM). This model is documented in the final report of the IBS Activity. The Systems Studies Activity contributed to enhancing the feedstock portion of the model by developing a coherent set of willow, poplar, and switchgrass production modules relevant to both the US and the UK. The Activity also developed a pretreatment module for switchgrass. Second, the Activity sponsored a three-day workshop on modeling bioenergy systems with the objectives of providing an overview of the types of models used to evaluate bioenergy and promoting communication among bioenergy modelers. There were nine guest speakers addressing different types of models used to evaluate different aspects of bioenergy, ranging from technoeconomic models based on the ASPEN software to linear programming models to develop feedstock supply curves for the US. The papers from this workshop have been submitted to Biomass and Bioenergy and are under editorial review.

  4. Systemic trauma.

    PubMed

    Goldsmith, Rachel E; Martin, Christina Gamache; Smith, Carly Parnitzke

    2014-01-01

    Substantial theoretical, empirical, and clinical work examines trauma as it relates to individual victims and perpetrators. As trauma professionals, it is necessary to acknowledge facets of institutions, cultures, and communities that contribute to trauma and subsequent outcomes. Systemic trauma-contextual features of environments and institutions that give rise to trauma, maintain it, and impact posttraumatic responses-provides a framework for considering the full range of traumatic phenomena. The current issue of the Journal of Trauma & Dissociation is composed of articles that incorporate systemic approaches to trauma. This perspective extends conceptualizations of trauma to consider the influence of environments such as schools and universities, churches and other religious institutions, the military, workplace settings, hospitals, jails, and prisons; agencies and systems such as police, foster care, immigration, federal assistance, disaster management, and the media; conflicts involving war, torture, terrorism, and refugees; dynamics of racism, sexism, discrimination, bullying, and homophobia; and issues pertaining to conceptualizations, measurement, methodology, teaching, and intervention. Although it may be challenging to expand psychological and psychiatric paradigms of trauma, a systemic trauma perspective is necessary on both scientific and ethical grounds. Furthermore, a systemic trauma perspective reflects current approaches in the fields of global health, nursing, social work, and human rights. Empirical investigations and intervention science informed by this paradigm have the potential to advance scientific inquiry, lower the incidence of a broader range of traumatic experiences, and help to alleviate personal and societal suffering. PMID:24617751

  5. Systemic fluoride.

    PubMed

    Sampaio, Fábio Correia; Levy, Steven Marc

    2011-01-01

    There is substantial evidence that fluoride, through different applications and formulas, works to control caries development. The first observations of fluoride's effects on dental caries were linked to fluoride naturally present in the drinking water, and then from controlled water fluoridation programs. Other systemic methods to deliver fluoride were later suggested, including dietary fluoride supplements such as salt and milk. These systemic methods are now being questioned due to the fact that many studies have indicated that fluoride's action relies mainly on its post-eruptive effect from topical contact with the tooth structure. It is known that even the methods of delivering fluoride known as 'systemic' act mainly through a topical effect when they are in contact with the teeth. The effectiveness of water fluoridation in many geographic areas is lower than in previous eras due to the widespread use of other fluoride modalities. Nevertheless, this evidence should not be interpreted as an indication that systemic methods are no longer relevant ways to deliver fluoride on an individual basis or for collective health programs. Caution must be taken to avoid excess ingestion of fluoride when prescribing dietary fluoride supplements for children in order to minimize the risk of dental fluorosis, particularly if there are other relevant sources of fluoride intake - such as drinking water, salt or milk and/or dentifrice. Safe and effective doses of fluoride can be achieved when combining topical and systemic methods. PMID:21701196

  6. Turbine system

    DOEpatents

    McMahan, Kevin Weston; Dillard, Daniel Jackson

    2016-05-03

    A turbine system is disclosed. The turbine system includes a transition duct having an inlet, an outlet, and a passage extending between the inlet and the outlet and defining a longitudinal axis, a radial axis, and a tangential axis. The outlet of the transition duct is offset from the inlet along the longitudinal axis and the tangential axis. The turbine system further includes a turbine section connected to the transition duct. The turbine section includes a plurality of shroud blocks at least partially defining a hot gas path, a plurality of buckets at least partially disposed in the hot gas path, and a plurality of nozzles at least partially disposed in the hot gas path. At least one of a shroud block, a bucket, or a nozzle includes means for withstanding high temperatures.

  7. Memory systems.

    PubMed

    Wolk, David A; Budson, Andrew E

    2010-08-01

    Converging evidence from patient and neuroimaging studies suggests that memory is a collection of abilities that use different neuroanatomic systems. Neurologic injury may impair one or more of these memory systems. Episodic memory allows us to mentally travel back in time and relive an episode of our life. Episodic memory depends on the hippocampus, other medial temporal lobe structures, the limbic system, and the frontal lobes, as well as several other brain regions. Semantic memory provides our general knowledge about the world and is unconnected to any specific episode of our life. Although semantic memory likely involves much of the neocortex, the inferolateral temporal lobes (particularly the left) are most important. Procedural memory enables us to learn cognitive and behavioral skills and algorithms that operate at an automatic, unconscious level. Damage to the basal ganglia, cerebellum, and supplementary motor area often impair procedural memory. PMID:22810510

  8. Lindenmayer Systems

    NASA Astrophysics Data System (ADS)

    Honkala, Juha

    The theory of Lindenmayer systems studies free monoid morphisms, free monoid substitutions and their iterations. In this chapter, we discuss similar ideas in a more general framework. Instead of a free monoid, we consider the free semi-algebra S<Σ*> consisting of polynomials with non-commuting variables in Σ and coefficients in a semiring S and we study the iteration of endomorphisms of S<Σ*>. We allow various modes of iteration and we consider various classes of morphisms. Classical L systems are obtained as special cases by taking S to be the Boolean semiring. Our approach also generalizes the theory of algebraic series in noncommuting variables.

  9. ELECTRONIC SYSTEM

    DOEpatents

    Robison, G.H. et al.

    1960-11-15

    An electronic system is described for indicating the occurrence of a plurality of electrically detectable events within predetermined time intervals. It is comprised of separate input means electrically associated with the events under observation: an electronic channel associated with each input means including control means and indicating means; timing means associated with each of the input means and the control means and adapted to derive a signal from the input means and apply it after a predetermined time to the control means to effect deactivation of each of the channels; and means for resetting the system to its initial condition after observation of each group of events.

  10. Complex Systems

    PubMed Central

    Goldberger, Ary L.

    2006-01-01

    Physiologic systems in health and disease display an extraordinary range of temporal behaviors and structural patterns that defy understanding based on linear constructs, reductionist strategies, and classical homeostasis. Application of concepts and computational tools derived from the contemporary study of complex systems, including nonlinear dynamics, fractals and “chaos theory,” is having an increasing impact on biology and medicine. This presentation provides a brief overview of an emerging area of biomedical research, including recent applications to cardiopulmonary medicine and chronic obstructive lung disease. PMID:16921107

  11. Computer systems

    NASA Technical Reports Server (NTRS)

    Olsen, Lola

    1992-01-01

    In addition to the discussions, Ocean Climate Data Workshop hosts gave participants an opportunity to hear about, see, and test for themselves some of the latest computer tools now available for those studying climate change and the oceans. Six speakers described computer systems and their functions. The introductory talks were followed by demonstrations to small groups of participants and some opportunities for participants to get hands-on experience. After this familiarization period, attendees were invited to return during the course of the Workshop and have one-on-one discussions and further hands-on experience with these systems. Brief summaries or abstracts of introductory presentations are addressed.

  12. Microbiology System

    NASA Technical Reports Server (NTRS)

    1992-01-01

    Technology originating in a NASA-sponsored study of the measurement of microbial growth in zero gravity led to the development of Biomerieux Vitek, Inc.'s VITEK system. VITEK provides a physician with accurate diagnostic information and identifies the most effective medication. Test cards are employed to identify organisms and determine susceptibility to antibiotics. A photo-optical scanner scans the card and monitors changes in the growth of cells contained within the card. There are two configurations - VITEK and VITEK JR as well as VIDAS, a companion system that detects bacteria, viruses, etc. from patient specimens. The company was originally created by McDonnell Douglas, the NASA contractor.

  13. The Cys18-Cys137 Disulfide Bond in Mouse Angiotensinogen Does Not Affect AngII-dependent Functions In Vivo

    PubMed Central

    Wu, Congqing; Xu, Yinchuan; Lu, Hong; Howatt, Deborah A.; Balakrishnan, Anju; Moorleghen, Jessica J.; Vander Kooi, Craig W.; Cassis, Lisa A.; Wang, Jian-an; Daugherty, Alan

    2015-01-01

    Renin cleavage of angiotensinogen (AGT) releases angiotensin I (AngI) in the initial step of producing all angiotensin peptides. It has been suggested recently that redox regulation of a disulfide bond in AGT involving Cys18-Cys137 may be important to its renin cleavage efficiency in vivo. The purpose of this study was to test this prediction in a mouse model by comparing AngII production and AngII-dependent functions in mice expressing wild-type AGT versus a mutated form of AGT lacking the disulfide bond. Wild-type (hepAGT+/+) and hepatocyte-specific AGT deficient (hepAGT−/−) littermates were developed in an LDL receptor −/− background. hepAGT+/+ mice were injected intraperitoneally with adeno-associated viral (AAV) vector containing a null insert. hepAGT−/− mice were injected with AAV containing a null insert, wild-type AGT, or Cys18Ser and Cys137Ser mutated AGT. Two weeks after AAV injection, mice were fed a Western diet for 12 weeks. Administration of AAV containing either form of AGT led to similar plasma AGT concentrations in hepAGT−/− mice. High plasma renin concentrations in hepAGT−/− mice were suppressed equally by both forms of AGT, which were accompanied by comparable increases of plasma AngII concentrations similar to hepAGT+/+ mice. AAV-driven expression of both forms of AGT led to equivalent increases of systolic blood pressure and augmentation of atherosclerotic lesion size in hepAGT−/− mice. These measurements were comparable to systolic blood pressure and atherosclerotic lesions in hepAGT+/+ mice. These data indicate that the Cys18-Cys137 disulfide bond in AGT is dispensable for AngII production and AngII-dependent functions in mice. PMID:25691624

  14. Auditory system

    NASA Technical Reports Server (NTRS)

    Ades, H. W.

    1973-01-01

    The physical correlations of hearing, i.e. the acoustic stimuli, are reported. The auditory system, consisting of external ear, middle ear, inner ear, organ of Corti, basilar membrane, hair cells, inner hair cells, outer hair cells, innervation of hair cells, and transducer mechanisms, is discussed. Both conductive and sensorineural hearing losses are also examined.

  15. Immune System

    EPA Science Inventory

    A properly functioning immune system is essential to good health. It defends the body against infectious agents and in some cases tumor cells. Individuals with immune deficiencies resulting from genetic defects, diseases (e.g., AIDS, leukemia), or drug therapies are more suscepti...

  16. Metric System.

    ERIC Educational Resources Information Center

    Del Mod System, Dover, DE.

    This autoinstructional unit deals with the identification of units of measure in the metric system and the construction of relevant conversion tables. Students in middle school or in grade ten, taking a General Science course, can handle this learning activity. It is recommended that high, middle or low level achievers can use the program.…

  17. Irrigation System

    NASA Technical Reports Server (NTRS)

    1984-01-01

    Under contract with Marshall Space Flight Center, Midwest Research Institute compiled a Lubrication Handbook intended as a reference source for designers and manufacturers of aerospace hardware and crews responsible for maintenance of such equipment. Engineers of Lindsay Manufacturing Company learned of this handbook through NASA Tech Briefs and used it for supplemental information in redesigning gear boxes for their center pivot agricultural irrigation system.

  18. Cardiovascular system

    MedlinePlus Videos and Cool Tools

    The cardiovascular system is composed of the heart and the network of arteries, veins, and capillaries that transport blood throughout the body. The ... which they are eliminated. Most of the blood is made up of a watery, protein-laden fluid ...

  19. Systems Science

    ERIC Educational Resources Information Center

    Christakis, Alexander; Hammond, Debora; Jackson, Michael; Laszlo, Alexander; Mitroff, Ian; Snowden, Dave; Troncale, Len; Carr-Chellman, Alison; Spector, J. Michael; Wilson, Brent

    2013-01-01

    Scholars representing the field of systems science were asked to identify what they considered to be the most exciting and imaginative work currently being done in their field, as well as how that work might change our understanding. The scholars included Alexander Christakis, Debora Hammond, Michael Jackson, Alexander Laszlo, Ian Mitroff, Dave…

  20. STAR System.

    ERIC Educational Resources Information Center

    Doverspike, James E.

    The STAR System is a developmental guidance approach to be used with elementary school children in the 5th or 6th grades. Two basic purposes underlie STAR: to increase learning potential and to enhance personal growth and development. STAR refers to 4 basic skills: sensory, thinking, adapting, and revising. Major components of the 4 skills are:…

  1. System Dynamics

    NASA Astrophysics Data System (ADS)

    Morecroft, John

    System dynamics is an approach for thinking about and simulating situations and organisations of all kinds and sizes by visualising how the elements fit together, interact and change over time. This chapter, written by John Morecroft, describes modern system dynamics which retains the fundamentals developed in the 1950s by Jay W. Forrester of the MIT Sloan School of Management. It looks at feedback loops and time delays that affect system behaviour in a non-linear way, and illustrates how dynamic behaviour depends upon feedback loop structures. It also recognises improvements as part of the ongoing process of managing a situation in order to achieve goals. Significantly it recognises the importance of context, and practitioner skills. Feedback systems thinking views problems and solutions as being intertwined. The main concepts and tools: feedback structure and behaviour, causal loop diagrams, dynamics, are practically illustrated in a wide variety of contexts from a hot water shower through to a symphony orchestra and the practical application of the approach is described through several real examples of its use for strategic planning and evaluation.

  2. Systems Biology

    SciTech Connect

    Wiley, H S.

    2006-06-01

    The biology revolution over the last 50 years has been driven by the ascendancy of molecular biology. This was enthusiastically embraced by most biologists because it took us into increasingly familiar territory. It took mysterious processes, such as the replication of genetic material and assigned them parts that could be readily understood by the human mind. When we think of ''molecular machines'' as being the underlying basis of life, we are using a paradigm derived from everyday experience. However, the price that we paid was a relentless drive towards reductionism and the attendant balkanization of biology. Now along comes ''systems biology'' that promises us a solution to the problem of ''knowing more and more about less and less''. Unlike molecular biology, systems biology appears to be taking us into unfamiliar intellectual territory, such as statistics, mathematics and computer modeling. Not surprisingly, systems biology has met with widespread skepticism and resistance. Why do we need systems biology anyway and how does this new area of research promise to change the face of biology in the next couple of decades?

  3. Surveying System

    NASA Technical Reports Server (NTRS)

    1988-01-01

    Sunrise Geodetic Surveys are setting up their equipment for a town survey. Their equipment differs from conventional surveying systems that employ transit rod and chain to measure angles and distances. They are using ISTAC Inc.'s Model 2002 positioning system, which offers fast accurate surveying with exceptional signals from orbiting satellites. The special utility of the ISTAC Model 2002 is that it can provide positioning of the highest accuracy from Navstar PPS signals because it requires no knowledge of secret codes. It operates by comparing the frequency and time phase of a Navstar signal arriving at one ISTAC receiver with the reception of the same set of signals by another receiver. Data is computer processed and translated into three dimensional position data - latitude, longitude and elevation.

  4. Burner systems

    DOEpatents

    Doherty, Brian J.

    1984-07-10

    A burner system particularly useful for downhole deployment includes a tubular combustion chamber unit housed within a tubular coolant jacket assembly. The combustion chamber unit includes a monolithic tube of refractory material whose inner surface defines the combustion zone. A metal reinforcing sleeve surrounds and extends the length of the refractory tube. The inner surface of the coolant jacket assembly and outer surface of the combustion chamber unit are dimensioned so that those surfaces are close to one another in standby condition so that the combustion chamber unit has limited freedom to expand with that expansion being stabilized by the coolant jacket assembly so that compression forces in the refractory tube do not exceed about one-half the safe compressive stress of the material; and the materials of the combustion chamber unit are selected to establish thermal gradient parameters across the combustion chamber unit to maintain the refractory tube in compression during combustion system start up and cool down sequences.

  5. Copernican System

    NASA Astrophysics Data System (ADS)

    Murdin, P.

    2000-11-01

    The heliocentric (i.e. `Sun-centered') theory proposed by the Polish astronomer Nicolaus Copernicus (1473-1543), and published by him in 1543 in his book, De Revolutionibus Orbium Coelestium. In this system Copernicus placed the Sun at the center of the universe and regarded the Earth and the planets as moving around it in circular orbits. Because of his retention of the notion of circular motion...

  6. Gasification system

    DOEpatents

    Haldipur, Gaurang B.; Anderson, Richard G.; Cherish, Peter

    1985-01-01

    A method and system for injecting coal and process fluids into a fluidized bed gasification reactor. Three concentric tubes extend vertically upward into the fluidized bed. Coal particulates in a transport gas are injected through an inner tube, and an oxygen rich mixture of oxygen and steam are injected through an inner annulus about the inner tube. A gaseous medium relatively lean in oxygen content, such as steam, is injected through an annulus surrounding the inner annulus.

  7. Gasification system

    DOEpatents

    Haldipur, Gaurang B.; Anderson, Richard G.; Cherish, Peter

    1983-01-01

    A method and system for injecting coal and process fluids into a fluidized bed gasification reactor. Three concentric tubes extend vertically upward into the fluidized bed. Coal particulates in a transport gas are injected through an inner tube, and an oxygen rich mixture of oxygen and steam are injected through an inner annulus about the inner tube. A gaseous medium relatively lean in oxygen content, such as steam, is injected through an annulus surrounding the inner annulus.

  8. Tychonic System

    NASA Astrophysics Data System (ADS)

    Murdin, P.

    2000-11-01

    The world system proposed in 1583 by the Danish astronomer Tycho Brahe (1546-1601). Unable to accept the Copernican doctrine that the Earth moves around the Sun, he put forward the view, later disproved by Kepler (1571-1630), that the planets move around the Sun, but the Sun and Moon move around the Earth. The theory explained the observed variations of the phases of Venus, for which the Ptolemai...

  9. Imaging System

    NASA Technical Reports Server (NTRS)

    1995-01-01

    The 1100C Virtual Window is based on technology developed under NASA Small Business Innovation (SBIR) contracts to Ames Research Center. For example, under one contract Dimension Technologies, Inc. developed a large autostereoscopic display for scientific visualization applications. The Virtual Window employs an innovative illumination system to deliver the depth and color of true 3D imaging. Its applications include surgery and Magnetic Resonance Imaging scans, viewing for teleoperated robots, training, and in aviation cockpit displays.

  10. Security system

    DOEpatents

    Baumann, Mark J.; Kuca, Michal; Aragon, Mona L.

    2016-02-02

    A security system includes a structure having a structural surface. The structure is sized to contain an asset therein and configured to provide a forceful breaching delay. The structure has an opening formed therein to permit predetermined access to the asset contained within the structure. The structure includes intrusion detection features within or associated with the structure that are activated in response to at least a partial breach of the structure.

  11. Mine system

    SciTech Connect

    Stoppani, B.R.

    1983-10-04

    A mine system comprises at least one mining machine adapted to haul itself, in a reciprocating manner, along a mineral face, and a control box housing means to control the various electrical elements of the machine(s), the box being located in a mine roadway at one end of the mineral face along which the machine(s) is reciprocating, and the box being electrically connected to a terminal box housed in a body of the machine(s).

  12. Systemic amyloidosis.

    PubMed

    Wechalekar, Ashutosh D; Gillmore, Julian D; Hawkins, Philip N

    2016-06-25

    Tissue deposition of protein fibrils causes a group of rare diseases called systemic amyloidoses. This Seminar focuses on changes in their epidemiology, the current approach to diagnosis, and advances in treatment. Systemic light chain (AL) amyloidosis is the most common of these conditions, but wild-type transthyretin cardiac amyloidosis (ATTRwt) is increasingly being diagnosed. Typing of amyloid fibrils, a critical determinant of therapy, has improved with the wide availability of laser capture and mass spectrometry from fixed histological tissue sections. Specific and accurate evaluation of cardiac amyloidosis is now possible using cardiac magnetic resonance imaging and cardiac repurposing of bone scintigraphy tracers. Survival in AL amyloidosis has improved markedly as novel chemotherapy agents have become available, but challenges remain in advanced disease. Early diagnosis, a key to better outcomes, still remains elusive. Broadening the amyloid-specific therapeutic landscape to include RNA inhibitors, fibril formation stabilisers and inhibitors, and immunotherapeutic targeting of amyloid deposits holds promise to transform outcomes in systemic amyloidoses. PMID:26719234

  13. Braking system

    DOEpatents

    Norgren, D.U.

    1982-09-23

    A balanced braking system comprising a plurality of braking assemblies located about a member to be braked. Each of the braking assemblies consists of a spring biased piston of a first material fitted into a body of a different material which has a greater contraction upon cooling than the piston material. The piston is provided with a recessed head portion over which is positioned a diaphragm and forming a space therebetween to which is connected a pressurized fluid supply. The diaphragm is controlled by the fluid in the space to contact or withdraw from the member to be braked. A cooling means causes the body within which the piston is fitted to contract more than the piston, producing a tight shrink fit therebetween. The braking system is particularly applicable for selectively braking an arbor of an electron microscope which immobilizes, for example, a vertically adjustable low temperature specimen holder during observation. The system provides balanced braking forces which can be easily removed and re-established with minimal disturbance to arbor location.

  14. Bearing system

    DOEpatents

    Kapich, Davorin D.

    1987-01-01

    A bearing system includes backup bearings for supporting a rotating shaft upon failure of primary bearings. In the preferred embodiment, the backup bearings are rolling element bearings having their rolling elements disposed out of contact with their associated respective inner races during normal functioning of the primary bearings. Displacement detection sensors are provided for detecting displacement of the shaft upon failure of the primary bearings. Upon detection of the failure of the primary bearings, the rolling elements and inner races of the backup bearings are brought into mutual contact by axial displacement of the shaft.

  15. Sterilization System

    NASA Technical Reports Server (NTRS)

    1990-01-01

    Cox Sterile Products, Inc.'s Rapid Heat Transfer Sterilizer employs a heat exchange process that induces rapid air movement; the air becomes the heat transfer medium, maintaining a uniform temperature of 375 degrees Fahrenheit. It features pushbutton controls for three timing cycles for different instrument loads, a six-minute cycle for standard unpackaged instruments, eight minutes for certain specialized dental/medical instruments and 12 minutes for packaged instruments which can then be stored in a drawer in sterile condition. System will stay at 375 degrees all day. Continuous operation is not expensive because of the sterilizer's very low power requirements.

  16. Relaxation System

    NASA Technical Reports Server (NTRS)

    1987-01-01

    Environ Corporation's relaxation system is built around a body lounge, a kind of super easy chair that incorporates sensory devices. Computer controlled enclosure provides filtered ionized air to create a feeling of invigoration, enhanced by mood changing aromas. Occupant is also surrounded by multidimensional audio and the lighting is programmed to change colors, patterns, and intensity periodically. These and other sensory stimulators are designed to provide an environment in which the learning process is stimulated, because research has proven that while an individual is in a deep state of relaxation, the mind is more receptive to new information.

  17. Purification system

    NASA Technical Reports Server (NTRS)

    Flanagan, David T. (Inventor); Gibbons, Randall E. (Inventor)

    1992-01-01

    A system for prolonging the life of a granulated activated charcoal (GAC) water treatment device is disclosed in which an ultraviolet light transparent material is used to constrain water to flow over carbon surfaces. It is configured to receive maximum flux from a UV radiation source for the purpose of preventing microbial proliferation on the carbon surfaces; oxidizing organic contaminants adsorbed from the water onto the carbon surfaces and from biodegradation of adsorbed microbial forms; disinfecting water; and oxidizing organic contaminants in the water.

  18. Videobasierte Systeme

    NASA Astrophysics Data System (ADS)

    Knoll, Peter

    Videosensoren spielen für Fahrerassistenz systeme eine zentrale Rolle, da sie die Interpretation visueller Informationen (Objektklassifikation) gezielt unterstützen. Im Heckbereich kann die Video sensorik in der einfachsten Variante die ultraschallbasierte Einparkhilfe bei Einpark- und Rangiervorgängen unterstützen. Beim Nachtsichtsystem NightVision wird das mit Infrarotlicht angestrahlte Umfeld vor dem Fahrzeug mit einer Frontkamera aufgenommen und im Fahrzeugcockpit auf einem Display dem Fahrer angezeigt (s. Nachtsichtsysteme). Andere Fahrerassistenzsysteme verarbeiten die Videosignale und generieren daraus gezielt Informationen, die für eigenständige Funktionen (z. B. Spurverlassenswarner) oder aber als Zusatzinformation für andere Funktionen ausgewertet werden (Sensordatenfusion).

  19. Balance System

    NASA Technical Reports Server (NTRS)

    1988-01-01

    TherEx Inc.'s AT-1 Computerized Ataxiameter precisely evaluates posture and balance disturbances that commonly accompany neurological and musculoskeletal disorders. Complete system includes two-strain gauged footplates, signal conditioning circuitry, a computer monitor, printer and a stand-alone tiltable balance platform. AT-1 serves as assessment tool, treatment monitor, and rehabilitation training device. It allows clinician to document quantitatively the outcome of treatment and analyze data over time to develop outcome standards for several classifications of patients. It can evaluate specifically the effects of surgery, drug treatment, physical therapy or prosthetic devices.

  20. Assessment of urinary angiotensinogen as a marker of podocyte injury in proteinuric nephropathies.

    PubMed

    Eriguchi, Masahiro; Yotsueda, Ryusuke; Torisu, Kumiko; Kawai, Yasuhiro; Hasegawa, Shoko; Tanaka, Shigeru; Noguchi, Hideko; Masutani, Kosuke; Kitazono, Takanari; Tsuruya, Kazuhiko

    2016-02-15

    Urinary protein (UP) is widely used as a clinical marker for podocyte injury; however, not all proteinuric nephropathies fit this model. We previously described the elevation of urinary angiotensinogen (AGT) accompanied by AGT expression by injured podocytes in a nitric oxide inhibition rat model (Eriguchi M, Tsuruya K, Haruyama N, Yamada S, Tanaka S, Suehiro T, Noguchi H, Masutani K, Torisu K, Kitazono T. Kidney Int 87: 116-127, 2015). In this report, we performed the human and animal studies to examine the significance and origin of urinary AGT. In the human study, focal segmental glomerulosclerosis (FSGS) patients presented with higher levels of urinary AGT, corrected by UP, than minimal-change disease (MCD) patients. Furthermore, AGT was evident in podocin-negative glomerular segmental lesions. We also tested two different nephrotic models induced by puromycin aminonucleoside in Wistar rats. The urinary AGT/UP ratio and AGT protein and mRNA expression in sieved glomeruli from FSGS rats were significantly higher than in MCD rats. The presence of AGT at injured podocytes in FSGS rats was detected by immunohistochemistry and immunoelectron microscopy. Finally, we observed the renal tissue and urinary metabolism of exogenous injected human recombinant AGT (which is not cleaved by rodent renin) in FSGS and control rats. Significant amounts of human AGT were detected in the urine of FSGS rats, but not of control rats. Immunostaining for rat and human AGT identified that only rat AGT was detected in injured podocytes, and filtered human AGT was seen in superficial proximal tubules, but not in injured podocytes, suggesting AGT generation by injured podocytes. In conclusion, the urinary AGT/UP ratio represents a novel specific marker of podocyte injury. PMID:26632605

  1. Transfer system

    DOEpatents

    Kurosawa, Kanji; Koga, Bunichiro; Ito, Hideki; Kiriyama, Shigeru; Higuchi, Shizuo

    2003-05-20

    A transport system includes a traveling rail (1) which constitutes a transport route and a transport body (3) which is capable of traveling on the traveling rail in the longitudinal direction of the traveling rail. Flexible drive tubes (5) are arranged on the traveling rail in the longitudinal direction of the traveling rail. The transport body includes a traveling wheel (4) which is capable of rolling on the traveling rail and drive wheels (2) which are capable of rolling on the drive tubes upon receiving the rotational drive power generated by pressure of a pressure medium supplied to the drive tubes while depressing the drive tubes. The traveling rail includes a plurality of transport sections and the transport body is capable of receiving a rotational drive force from the drive tubes at every transport sections. If necessary, a transport route changeover switch which changes over the transport route can be provided between the transport sections.

  2. Dataflow systems

    SciTech Connect

    Cohen, A.T.

    1982-01-01

    Dataflow languages are stream-oriented and functional, and assume a different operating environment. Programs in these languages are functions which define output as a function of input, with each program being a composition of subfunctions. There is no notion of a global store and, hence, there are no assignment statements. Control flow is determined by the availability of data (function arguments) and need not be explicitly specified by the programmer. The use and development of dataflow languages are motivated by three considerations. They represent parallelism naturally, particularly as it occurs in networks and distributed systems. They readily support very high level programming and their modularity and lack of side-effects makes their programs amenable to analysis. The paper briefly discusses their advantages in each of these three areas. 32 references.

  3. Systems toxicology.

    PubMed

    Hartung, Thomas; van Vliet, Erwin; Jaworska, Joanna; Bonilla, Leo; Skinner, Nigel; Thomas, Russell

    2012-01-01

    The need for a more mechanistic understanding of the ways in which chemicals modulate biological pathways is urgent if we are to identify and better assess safety issues relating to a wide range of substances developed by the pharmaceutical, chemical, agri-bio, and cosmetic industries. Omics technologies provide a valuable opportunity to refine existing methods and provide information for so-called integrated testing strategies via the creation of signatures of toxicity. By mapping these signatures to underlying pathways of toxicity, some of which have been identified by toxicologists over the last few decades, and bringing them together with pathway information determined from biochemistry and molecular biology, a "systems toxicology" approach will enable virtual experiments to be conducted that can improve the prediction of hazard and the assessment of compound toxicity. PMID:22562485

  4. Intelligent Engine Systems: Bearing System

    NASA Technical Reports Server (NTRS)

    Singh, Arnant P.

    2008-01-01

    The overall requirements necessary for sensing bearing distress and the related criteria to select a particular rotating sensor were established during the phase I. The current phase II efforts performed studies to evaluate the Robustness and Durability Enhancement of the rotating sensors, and to design, and develop the Built-in Telemetry System concepts for an aircraft engine differential sump. A generic test vehicle that can test the proposed bearing diagnostic system was designed, developed, and built. The Timken Company, who also assisted with testing the GE concept of using rotating sensors for the differential bearing diagnostics during previous phase, was selected as a subcontractor to assist General Electric (GE) for the design, and procurement of the test vehicle. A purchase order was prepared to define the different sub-tasks, and deliverables for this task. The University of Akron was selected to provide the necessary support for installing, and integrating the test vehicle with their newly designed test facility capable of simulating the operating environment for the planned testing. The planned testing with good and damaged bearings will be on hold pending further continuation of this effort during next phase.

  5. Separation system

    DOEpatents

    Rubin, Leslie S.

    1986-01-01

    A separation system for dewatering radioactive waste materials includes a disposal container, drive structure for receiving the container, and means for releasably attaching the container to the drive structure. Separation structure disposed in the container adjacent the inner surface of the side wall structure retains solids while allowing passage of liquids. Inlet port structure in the container top wall is normally closed by first valve structure that is centrifugally actuated to open the inlet port and discharge port structure at the container periphery receives liquid that passes through the separation structure and is normally closed by second valve structure that is centrifugally actuated to open the discharge ports. The container also includes coupling structure for releasable engagement with the centrifugal drive structure. Centrifugal force produced when the container is driven in rotation by the drive structure opens the valve structures, and radioactive waste material introduced into the container through the open inlet port is dewatered, and the waste is compacted. The ports are automatically closed by the valves when the container drum is not subjected to centrifugal force such that containment effectiveness is enhanced and exposure of personnel to radioactive materials is minimized.

  6. [Systemic sclerosis].

    PubMed

    Tamborrini, Giorgio; Distler, Meike; Distler, Oliver

    2008-05-01

    Systemic sclerosis (SSc) is a severe fibrotic multiorgan connective tissue disease. Vascular abnormalities such as fingertip ulcers and Raynaud's syndrome as well as involvement of organs including the lungs, heart, kidney and the gastrointestinal tract are prominent features of the disease. There are currently no disease modifying drugs available that can modify the course of the disease. In this review we will discuss medications that have been found to be effective in improving specific organ involvement due to SSc. For the treatment of gastroesophageal reflux disease (GERD), proton pump inhibitors are effective agents. In the setting of clinically significant gastrointestinal dysmotility, metoclopramide, erythromycin and octreotide may be beneficial. Small bowel bacterial overgrowth should be treated with oral antibiotics. Angiotensin converting enzyme inhibitors are the first-line agents for acute renal crisis. A variety of treatment options are available for Raynaud's phenomenon and include calcium channel blockers, iloprost (i. v.), losartan, fluoxetine and sildenafil. Fingertip ulcers can be prevented by using the endothelin receptor antagonist bosentan. The therapeutic options for treatment of pulmonary hypertension associated with SSc include bosentan, sildenafil and various prostacyclin analogs (eg, epoprostenol, treprostinil, iloprost). Sitaxentan, ambrisentan and new phosphodiesterase-5 inhibitors could be new options for therapy as well. Therapeutic options for interstitial lung fibrosis include cyclophosphamide, however, clinical effects are mild to moderate. Methotrexate has been used to treat skin fibrosis and can be beneficial when arthritis is present. PMID:18552072

  7. Incinerator system

    SciTech Connect

    Rathmell, R.K.

    1986-10-07

    An incineration system is described which consists of: combustion chamber structure having an inlet, an outlet, and burner structure in the combustion chamber, heat exchanger structure defining a chamber, divider structure between the heat exchanger chamber and the combustion chamber, an array of tubes extending through the heat exchanger chamber to the inlet of the combustion chamber at the divider structure. The heat exchanger chamber has an inlet coupled to the outlet of the combustion chamber for flow of the combustion products discharged from the combustion chamber through the heat exchanger chamber over the tubes in heat exchange relation, and an outlet for discharge of products from the heat exchanger chamber, aspirator sleeve structure secured to the divider structure between the heat exchanger chamber and the combustion chamber. Each aspirator sleeve receives the outlet end of a heat exchanger tube in slip fit relation so that the heat exchanger tubes are free to thermally expand longitudinally within the aspirator sleeves, and means for flowing vapor through the heat exchanger tubes into the combustion chamber at sufficiently high velocity to produce a reduced pressure effect in the aspirator sleeves in the heat exchanger chamber to draw a minor fraction of combustion products through the aspirator sleeves into the combustion chamber for reincineration.

  8. New Systems Produced by Systemic Change

    ERIC Educational Resources Information Center

    Battino, Wendy; Clem, Jo; Caine, Renate N.; Reigeluth, Charles M.; Chapman, Carrie; Flinders, David J.; Malopinsky, Larissa V.

    2006-01-01

    This article presents new systems produced by systemic change. First is Systemic Changes in the Chugach School District by Wendy Battino and Jo Clem. Second is Systemic Changes in Public Schools through Brain-Based Learning by Renate N. Caine. Third is A Vision of an Information-Age Educational System by Charles M. Reigeluth. Fourth is Systemic…

  9. System safety education focused on system management

    NASA Technical Reports Server (NTRS)

    Grose, V. L.

    1971-01-01

    System safety is defined and characteristics of the system are outlined. Some of the principle characteristics include role of humans in hazard analysis, clear language for input and output, system interdependence, self containment, and parallel analysis of elements.

  10. Distinguishing Systemic from Systematic.

    ERIC Educational Resources Information Center

    Carr, Alison A.

    1996-01-01

    Describes the difference between systemic and systematic as they relate to school reform and instructional design. Highlights include a history of systems theory; systems engineering; instructional systems design; systemic versus reductionist thinking; social systems; and systemic change in education, including power relationships. (LRW)

  11. Obstacle detectors for automated transit vehicles: A technoeconomic and market analysis

    NASA Technical Reports Server (NTRS)

    Lockerby, C. E.

    1979-01-01

    A search was conducted to identify the technical and economic characteristics of both NASA and nonNASA obstacle detectors. The findings, along with market information were compiled and analyzed for consideration by DOT and NASA in decisions about any future automated transit vehicle obstacle detector research, development, or applications project. Currently available obstacle detectors and systems under development are identified by type (sonic, capacitance, infrared/optical, guided radar, and probe contact) and compared with the three NASA devices selected as possible improvements or solutions to the problems in existing obstacle detection systems. Cost analyses and market forecasts individually for the AGT and AMTV markets are included.

  12. Quantization of integrable systems and a 2d/4d duality

    NASA Astrophysics Data System (ADS)

    Dorey, Nick; Lee, Sungjay; Hollowood, Timothy J.

    2011-10-01

    We present a new duality between the F-terms of supersymmetric field theories defined in two-and four-dimensions respectively. The duality relates mathcal{N} = 2 super-symmetric gauge theories in four dimensions, deformed by an Ω-background in one plane, to mathcal{N} = left( {2,2} right) gauged linear σ-models in two dimensions. On the four dimensional side, our main example is mathcal{N} = 2 SQCD with gauge group G = SU( L) and N F = 2 L fundamental flavours. Using ideas of Nekrasov and Shatashvili, we argue that the Coulomb branch of this theory provides a quantization of the classical Heisenberg SL(2) spin chain. Agreement with the standard quantization via the Algebraic Bethe Ansatz implies the existence of an isomorphism between the chiral ring of the 4 d theory and that of a certain two-dimensional theory. The latter can be understood as the worldvolume theory on a surface operator/vortex string probing the Higgs branch of the same 4 d theory. We check the proposed duality by explicit calculation at low orders in the instanton expansion. One striking consequence is that the Seiberg-Witten solution of the 4 d theory is captured by a one-loop computation in two dimensions. The duality also has interesting connections with the AGT conjecture, matrix models and topological string theory where it corresponds to a refined version of the geometric transition.

  13. System design description cone penetrometer system

    SciTech Connect

    Seda, R.Y., Westinghouse Hanford

    1996-08-12

    The system design description documents in detail the design of the cone penetrometer system. The systems includes the cone penetrometer physical package, raman spectroscopy package and moisture sensor package. Information pertinent to the system design, development, fabrication and testing is provided.

  14. Systems view of power systems autonomy

    SciTech Connect

    Anderson, J.L.

    1984-08-01

    A space station will involve the formation and sustained operation of an assembly of humans and machines in space for a period of 10-20 years. Technology and mission studies of a permanently manned, evolutionary space station have identified the need for automated and eventually some degree of autonomous systems operation. A space station power system will have a high degree of interaction with other onboard systems which will act as power loads. By examining the evolution of an operational power system from a systems viewpoint through increasing degrees of automation the system and technology requirements are identified for an evolutionary system.

  15. Networked control of microgrid system of systems

    NASA Astrophysics Data System (ADS)

    Mahmoud, Magdi S.; Rahman, Mohamed Saif Ur; AL-Sunni, Fouad M.

    2016-08-01

    The microgrid has made its mark in distributed generation and has attracted widespread research. However, microgrid is a complex system which needs to be viewed from an intelligent system of systems perspective. In this paper, a network control system of systems is designed for the islanded microgrid system consisting of three distributed generation units as three subsystems supplying a load. The controller stabilises the microgrid system in the presence of communication infractions such as packet dropouts and delays. Simulation results are included to elucidate the effectiveness of the proposed control strategy.

  16. Systems design of long-life systems

    NASA Technical Reports Server (NTRS)

    Miles, R. F., Jr.

    1974-01-01

    A long-life system is defined as a system which cannot be life-tested in its operational environment. Another restriction is that preventive maintenance and repair shall be either impossible or economically disadvantageous. Examples of such systems include planetary spacecraft, communication satellites, undersea telephone cables, and nuclear power plants. The questions discussed are related to the implementation of system functions, approaches to determine the required level of system reliability, and aspects of tradeoffs between requirements and reliability.

  17. Female Reproductive System

    MedlinePlus

    ... How Can I Help a Friend Who Cuts? Female Reproductive System KidsHealth > For Teens > Female Reproductive System Print A ... and female reproductive systems. continue What Is the Female Reproductive System? Most species have two sexes: male and female. ...

  18. Multiple System Atrophy

    MedlinePlus

    ... Enhancing Diversity Find People About NINDS NINDS Multiple System Atrophy Information Page Condensed from Multiple System Atrophy ... Trials Organizations Publicaciones en Español What is Multiple System Atrophy? Multiple system atrophy (MSA) is a progressive ...

  19. System of systems modeling and analysis.

    SciTech Connect

    Campbell, James E.; Anderson, Dennis James; Longsine, Dennis E.; Shirah, Donald N.

    2005-01-01

    This report documents the results of an LDRD program entitled 'System of Systems Modeling and Analysis' that was conducted during FY 2003 and FY 2004. Systems that themselves consist of multiple systems (referred to here as System of Systems or SoS) introduce a level of complexity to systems performance analysis and optimization that is not readily addressable by existing capabilities. The objective of the 'System of Systems Modeling and Analysis' project was to develop an integrated modeling and simulation environment that addresses the complex SoS modeling and analysis needs. The approach to meeting this objective involved two key efforts. First, a static analysis approach, called state modeling, has been developed that is useful for analyzing the average performance of systems over defined use conditions. The state modeling capability supports analysis and optimization of multiple systems and multiple performance measures or measures of effectiveness. The second effort involves time simulation which represents every system in the simulation using an encapsulated state model (State Model Object or SMO). The time simulation can analyze any number of systems including cross-platform dependencies and a detailed treatment of the logistics required to support the systems in a defined mission.

  20. System Software Framework for System of Systems Avionics

    NASA Technical Reports Server (NTRS)

    Ferguson, Roscoe C.; Peterson, Benjamin L; Thompson, Hiram C.

    2005-01-01

    Project Constellation implements NASA's vision for space exploration to expand human presence in our solar system. The engineering focus of this project is developing a system of systems architecture. This architecture allows for the incremental development of the overall program. Systems can be built and connected in a "Lego style" manner to generate configurations supporting various mission objectives. The development of the avionics or control systems of such a massive project will result in concurrent engineering. Also, each system will have software and the need to communicate with other (possibly heterogeneous) systems. Fortunately, this design problem has already been solved during the creation and evolution of systems such as the Internet and the Department of Defense's successful effort to standardize distributed simulation (now IEEE 1516). The solution relies on the use of a standard layered software framework and a communication protocol. A standard framework and communication protocol is suggested for the development and maintenance of Project Constellation systems. The ARINC 653 standard is a great start for such a common software framework. This paper proposes a common system software framework that uses the Real Time Publish/Subscribe protocol for framework-to-framework communication to extend ARINC 653. It is highly recommended that such a framework be established before development. This is important for the success of concurrent engineering. The framework provides an infrastructure for general system services and is designed for flexibility to support a spiral development effort.

  1. Intelligent systems technology infrastructure for integrated systems

    NASA Technical Reports Server (NTRS)

    Lum, Henry, Jr.

    1991-01-01

    Significant advances have occurred during the last decade in intelligent systems technologies (a.k.a. knowledge-based systems, KBS) including research, feasibility demonstrations, and technology implementations in operational environments. Evaluation and simulation data obtained to date in real-time operational environments suggest that cost-effective utilization of intelligent systems technologies can be realized for Automated Rendezvous and Capture applications. The successful implementation of these technologies involve a complex system infrastructure integrating the requirements of transportation, vehicle checkout and health management, and communication systems without compromise to systems reliability and performance. The resources that must be invoked to accomplish these tasks include remote ground operations and control, built-in system fault management and control, and intelligent robotics. To ensure long-term evolution and integration of new validated technologies over the lifetime of the vehicle, system interfaces must also be addressed and integrated into the overall system interface requirements. An approach for defining and evaluating the system infrastructures including the testbed currently being used to support the on-going evaluations for the evolutionary Space Station Freedom Data Management System is presented and discussed. Intelligent system technologies discussed include artificial intelligence (real-time replanning and scheduling), high performance computational elements (parallel processors, photonic processors, and neural networks), real-time fault management and control, and system software development tools for rapid prototyping capabilities.

  2. Systems engineering and analysis

    SciTech Connect

    Blanchard, B.S.; Fabrycky, W.J.

    1981-01-01

    An introduction to systems is provided and tools for systems analysis are considered, taking into account system definitions and concepts, approaches for bringing systems into being, models in systems analysis, economic analysis techniques, mathematical modeling and optimization, probability and statistics, queuing theory and analysis, and control concepts and techniques. The system design process is discussed along with the design for operational feasibility, systems engineering management, and system design case studies. Attention is given to conceptual design, preliminary system design, detail design and development, system test and evaluation, design for reliability, design for maintainability, design for supportability, design for economic feasibility, communication system design, finite population system design, energy storage system design, and procurement-inventory system design.

  3. [X-33 Systems

    NASA Technical Reports Server (NTRS)

    1999-01-01

    Lockheed Martin Skunk Works has compiled an Annual Performance Report of the X-33/RLV Program. This report consists of individual reports from all industry team members, as well as NASA team centers. This portion of the report is comprised of a status report of Allied-Signal Aerospace's contribution to the program. The following is a summary of the work reviewed under their portion of the agreement: (1) Communication Systems; (2) Environmental Control Systems- Active Thermal Control System (ATCS), Purge and Vent System, Hydrogen Detection System (HDS), Avionics Bay Inerting System (ABIS), and Flush Air Data System (FADS); (2) Landing Systems; (3) Power Management and Generation Systems; (4) Flight Control Actuation System (FCAS)- Electric Power Control & Distribution System (EPCDS), and Battery Power System (BPS); and (5) Vehicle Management Systems (VMS)- VMS Hardware, VMS Software Development Activities, and System Integration Laboratory (SIL).

  4. Freedom System Text and Graphics System (TAGS)

    NASA Technical Reports Server (NTRS)

    1989-01-01

    The Text and Graphics System (TAGS) is a high-resolution facsimile system that scans text or graphics material and converts the analog SCAN data into serial digital data. This video shows the TAGS in operation.

  5. Language as a System of Systems

    ERIC Educational Resources Information Center

    Mulder, J. W. F.; Hervey, S. G. J.

    1975-01-01

    Based on Mulder's previous classification of all semiotic systems designed to describe the system of discrete features in human languages, this article explores a further subclassification of the genus language into species. (CLK)

  6. Intelligent tutoring systems for systems engineering methodologies

    NASA Technical Reports Server (NTRS)

    Meyer, Richard J.; Toland, Joel; Decker, Louis

    1991-01-01

    The general goal is to provide the technology required to build systems that can provide intelligent tutoring in IDEF (Integrated Computer Aided Manufacturing Definition Method) modeling. The following subject areas are covered: intelligent tutoring systems for systems analysis methodologies; IDEF tutor architecture and components; developing cognitive skills for IDEF modeling; experimental software; and PC based prototype.

  7. System Design of the SWRL Financial System.

    ERIC Educational Resources Information Center

    Ikeda, Masumi

    To produce various management and accounting reports in order to maintain control of SWRL (Southwest Regional Laboratory) operational and financial activities, a computer-based SWRL financial system was developed. The system design is outlined, and various types of system inputs described. The kinds of management and accounting reports generated…

  8. Optical system defect propagation in ABCD systems.

    PubMed

    McKinley, W G; Yura, H T; Hanson, S G

    1988-05-01

    We describe how optical system defects (tilt/jitter, decenter, and despace) propagate through an arbitrary paraxial optical system that can be described by an ABCD ray transfer matrix. A pedagogical example is given that demonstrates the effect of alignment errors on a typical optical system. PMID:19745889

  9. General Systems Theory and Instructional Systems Design.

    ERIC Educational Resources Information Center

    Salisbury, David F.

    1990-01-01

    Describes basic concepts in the field of general systems theory (GST) and identifies commonalities that exist between GST and instructional systems design (ISD). Models and diagrams that depict system elements in ISD are presented, and two matrices that show how GST has been used in ISD literature are included. (11 references) (LRW)

  10. DDL system: Design systhesis of digital systems

    NASA Technical Reports Server (NTRS)

    Shiva, S. G.

    1983-01-01

    Digital Systems Design Language was integrated into the CADAT system environment of NASA-MSFC. The major technical aspects of this integration are summarized. Automatic hardware synthesis is now possible starting with a high level description of the system to be synthesized. The DDL system provides a high level design verification capability, thereby minimizing design changes in the later stages of the design cycle. An overview of the DDL system covering the translation, simulation and synthesis capabilities is provided. Two companion documents (the user's and programmer's manuals) are to be consulted for detailed discussions.

  11. Lighting system with thermal management system

    SciTech Connect

    Arik, Mehmet; Weaver, Stanton Earl; Stecher, Thomas Elliot; Seeley, Charles Erklin; Kuenzler, Glenn Howard; Wolfe, Jr., Charles Franklin; Utturkar, Yogen Vishwas; Sharma, Rajdeep; Prabhakaran, Satish; Icoz, Tunc

    2015-08-25

    Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system is configured to provide an air flow, such as a unidirectional air flow, through the housing structure in order to cool the light source. The driver electronics are configured to provide power to each of the light source and the thermal management system.

  12. Lighting system with thermal management system

    DOEpatents

    Arik, Mehmet; Weaver, Stanton; Stecher, Thomas; Seeley, Charles; Kuenzler, Glenn; Wolfe, Jr., Charles; Utturkar, Yogen; Sharma, Rajdeep; Prabhakaran, Satish; Icoz, Tunc

    2013-05-07

    Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system is configured to provide an air flow, such as a unidirectional air flow, through the housing structure in order to cool the light source. The driver electronics are configured to provide power to each of the light source and the thermal management system.

  13. Lighting system with thermal management system

    DOEpatents

    Arik, Mehmet; Weaver, Stanton Earl; Stecher, Thomas Elliot; Seeley, Charles Erklin; Kuenzler, Glenn Howard; Wolfe, Jr., Charles Franklin; Utturkar, Yogen Vishwas; Sharma, Rajdeep; Prabhakaran, Satish; Icoz, Tunc

    2015-02-24

    Lighting systems having unique configurations are provided. For instance, the lighting system may include a light source, a thermal management system and driver electronics, each contained within a housing structure. The light source is configured to provide illumination visible through an opening in the housing structure. The thermal management system is configured to provide an air flow, such as a unidirectional air flow, through the housing structure in order to cool the light source. The driver electronics are configured to provide power to each of the light source and the thermal management system.

  14. Microwave landing system autoland system analysis

    NASA Technical Reports Server (NTRS)

    Feather, J. B.; Craven, B. K.

    1991-01-01

    The objective was to investigate the ability of present day aircraft equipped with automatic flight control systems to fly advanced Microwave Landing Systems (MLS) approaches. The tactical approach used to achieve this objective included reviewing the design and autoland operation of the MD-80 aircraft, simulating the MLS approaches using a batch computer program, and assessing the performance of the autoland system from computer generated data. The results showed changes were required to present Instrument Landing System (ILS) procedures to accommodate the new MLS curved paths. It was also shown that in some cases, changes to the digital flight guidance systems would be required so that an autoland could be performed.

  15. Intelligent test integration system

    NASA Technical Reports Server (NTRS)

    Sztipanovits, J.; Padalkar, S.; Rodriguez-Moscoso, J.; Kawamura, K.; Purves, B.; Williams, R.; Biglari, H.

    1988-01-01

    A new test technology is described which was developed for space system integration. The ultimate purpose of the system is to support the automatic generation of test systems in real time, distributed computing environments. The Intelligent Test Integration System (ITIS) is a knowledge based layer above the traditional test system components which can generate complex test configurations from the specification of test scenarios.

  16. Collaborative Systems Testing

    ERIC Educational Resources Information Center

    Pocatilu, Paul; Ciurea, Cristian

    2009-01-01

    Collaborative systems are widely used today in various activity fields. Their complexity is high and the development involves numerous resources and costs. Testing collaborative systems has a very important role for the systems' success. In this paper we present taxonomy of collaborative systems. The collaborative systems are classified in many…

  17. Energy Systems Design

    NASA Technical Reports Server (NTRS)

    1986-01-01

    PRESTO, a COSMIC program, handles energy system specifications and predicts design efficiency of cogeneration systems. These systems allow a company to use excess energy produced to generate electricity. PRESTO is utilized by the Energy Systems Division of Thermo Electron Corporation in the custom design of cogeneration systems.

  18. Systems Intelligence Inventory

    ERIC Educational Resources Information Center

    Törmänen, Juha; Hämäläinen, Raimo P.; Saarinen, Esa

    2016-01-01

    Purpose: Systems intelligence (SI) (Saarinen and Hämäläinen, 2004) is a construct defined as a person's ability to act intelligently within complex systems involving interaction and feedback. SI relates to our ability to act in systems and reason about systems to adaptively carry out productive actions within and with respect to systems such as…

  19. The LSST: A System of Systems

    NASA Astrophysics Data System (ADS)

    Claver, Chuck F.; Debois-Felsmann, G. P.; Delgado, F.; Hascall, P.; Marshall, S.; Nordby, M.; Schumacher, G.; Sebag, J.; LSST Collaboration

    2011-01-01

    The Large Synoptic Survey Telescope (LSST) is a complete observing system that acquires and archives images, processes and analyzes them, and publishes reduced images and catalogs of sources and objects. The LSST will operate over a ten year period producing a survey of 20,000 square degrees over the entire [Southern] sky in 6 filters (ugrizy) with each field having been visited several hundred times enabling a wide spectrum of science from fast transients to exploration of dark matter and dark energy. The LSST itself is a complex system of systems consisting of the 8.4m 3-mirror telescope, a 3.2 billion pixel camera, and a peta-scale data management system. The LSST project uses a Model Based Systems Engineering (MBSE) methodology to ensure an integrated approach to system design and rigorous definition of system interfaces and specifications. The MBSE methodology is applied through modeling of the LSST's systems with the System Modeling Language (SysML). The SysML modeling recursively establishes the threefold relationship between requirements, logical & physical functional decomposition and definition, and system and component behavior at successively deeper level of abstraction and detail. The LSST modeling includes the analysis and documenting the flow of command and control information and data between the suite of systems in the LSST observatory that are needed to carry out the activities of the survey. The MBSE approach is applied throughout all stages of the project from design, to validation and verification, though to commissioning.

  20. Hypoxia-Induced Endothelial Progenitor Cell Function Is Blunted in Angiotensinogen Knockout Mice

    PubMed Central

    Choi, Jin-Hwa; Nguyen, Minh-Phuong; Lee, Dongjin; Oh, Goo-Taeg; Lee, You-Mie

    2014-01-01

    Angiotensinogen (AGT), the precursor of angiotensin I, is known to be involved in tumor angiogenesis and associated with the pathogenesis of coronary atherosclerosis. This study was undertaken to determine the role played by AGT in endothelial progenitor cells (EPCs) in tumor progression and metastasis. It was found that the number of EPC colonies formed by AGT heterozygous knockout (AGT+/−) cells was less than that formed by wild-type (WT) cells, and that the migration and tube formation abilities of AGT+/− EPCs were significantly lower than those of WT EPCs. In addition, the gene expressions of vascular endothelial growth factor (VEGF), Flk1, angiopoietin (Ang)-1, Ang-2, Tie-2, stromal derived factor (SDF)-1, C-X-C chemokine receptor type 4 (CXCR4), and of endothelial nitric oxide synthase (eNOS) were suppressed in AGT+/− EPCs. Furthermore, the expressions of hypoxia-inducible factor (HIF)-1α and -2α were downregulated in AGT+/− early EPCs under hypoxic conditions, suggesting a blunting of response to hypoxia. Moreover, the activation of Akt/eNOS signaling pathways induced by VEGF, epithelial growth factor (EGF), or SDF-1α were suppressed in AGT+/− EPCs. In AGT+/− mice, the incorporation of EPCs into the tumor vasculature was significantly reduced, and lung tumor growth and melanoma metastasis were attenuated. In conclusion, AGT is required for hypoxia-induced vasculogenesis. PMID:24938229

  1. Levonorgestrel Intrauterine System

    MedlinePlus

    ... new system inserted at any time during your menstrual cycle. If you have chosen to use a different ... of your intrauterine system and you have regular menstrual cycles, you should have the system removed during the ...

  2. Manned systems technology discipline

    NASA Technical Reports Server (NTRS)

    Bretoi, Remus

    1990-01-01

    Viewgraphs on manned systems technology discipline for Space Station Freedom are presented. Topics covered include: crew-systems interfaces and interactions; crew training; on-board systems maintenance and support; habitability and environment; and computational human factors.

  3. Autonomic Nervous System Disorders

    MedlinePlus

    Your autonomic nervous system is the part of your nervous system that controls involuntary actions, such as the beating of your heart ... breathing and swallowing Erectile dysfunction in men Autonomic nervous system disorders can occur alone or as the result ...

  4. Autonomic Nervous System Disorders

    MedlinePlus

    Your autonomic nervous system is the part of your nervous system that controls involuntary actions, such as the beating ... with breathing and swallowing Erectile dysfunction in men Autonomic nervous system disorders can occur alone or as ...

  5. Immune System Involvement

    MedlinePlus

    ... Tips" to find out more! Email * Zipcode The Immune System and Psoriatic Disease What is an autoimmune disease? ... swollen and painful joints and tendons. Treating the immune system The immune system is not only the key ...

  6. Female Reproductive System

    MedlinePlus

    ... Story" 5 Things to Know About Zika & Pregnancy Female Reproductive System KidsHealth > For Parents > Female Reproductive System Print A ... the egg or sperm. continue Components of the Female Reproductive System Unlike the male, the human female has a ...

  7. Wind energy systems

    NASA Technical Reports Server (NTRS)

    Stewart, H. J.

    1978-01-01

    A discussion on wind energy systems involved with the DOE wind energy program is presented. Some of the problems associated with wind energy systems are discussed. The cost, efficiency, and structural design of wind energy systems are analyzed.

  8. Photovoltaic systems test facility

    NASA Technical Reports Server (NTRS)

    1979-01-01

    Facility provides broad and flexible capability for evaluating photovoltaic systems and design concepts. As 'breadboard' system, it can be used to check out complete systems, subsystems, and components before installation in actual service.

  9. Alternative Videodisc Systems.

    ERIC Educational Resources Information Center

    Heath, Ted

    1981-01-01

    Discusses consumer and industrial videodisc systems for information storage including cost, technology utilized, formats, and features. Reflective and transmissive laser optical systems are described, as well as the grooved and grooveless mechanical systems. Tables containing product data are included. (JJD)

  10. Emerging Systems of Systems for Environmental Data

    NASA Astrophysics Data System (ADS)

    Middleton, D. E.; Fox, P.; Cinquini, L.; Burek, M.

    2007-05-01

    The scientific research community increasingly has complex, difficult questions to ask of its observations and model results - questions that will increasingly span disparate datasets, multiple disciplines, and international boundaries. Our future information systems are going to need to satisfy these growing demands. GEOSS, the Global Earth Observing System of Systems, puts forth a compelling vision in this area. Solid steps in the direction of this vision are already well underway, moving us towards the next generation of global, federated environmental data systems. For example, last year the World Meteorological Organization demonstrated its first prototype for WIS, the WMO Information System. WIS is a step in the direction of GEOSS, providing a federated system that provides aggregation of environmental data and services at national and regional levels, combined with a small number of redundant peer systems that can service large-scale geographical regions. Forming a foundational layer for efforts like WIS, the global community is in the process of building other systems of systems that essentially aggregate and integrate the output of data and modeling efforts, in areas such as weather, climate, space physics, and many others. This encouraging trend towards federation of new and existing systems is driven by scientific needs and underpinned by shared technology, interfaces, protocols, metadata standards, and the world of Grid computing. NCAR, working with many partners, is contributing to a number of projects that are focused upon some of these challenges. In this presentation we will describe a suite of complimentary and interconnected efforts, including the Earth System Grid (climate), the Community Data Portal (and WIS connections), TIGGE (weather), the Virtual Solar Terrestrial Observatory, and related metadata thrusts. The main emphasis here is the pursuit of systems of systems as well as progress towards semantic integration, which will be very

  11. Propulsion Systems Panel deliberations

    NASA Technical Reports Server (NTRS)

    Bianca, Carmelo J.; Miner, Robert; Johnston, Lawrence M.; Bruce, R.; Dennies, Daniel P.; Dickenson, W.; Dreshfield, Robert; Karakulko, Walt; Mcgaw, Mike; Munafo, Paul M.

    1993-01-01

    The Propulsion Systems Panel was established because of the specialized nature of many of the materials and structures technology issues related to propulsion systems. This panel was co-chaired by Carmelo Bianca, MSFC, and Bob Miner, LeRC. Because of the diverse range of missions anticipated for the Space Transportation program, three distinct propulsion system types were identified in the workshop planning process: liquid propulsion systems, solid propulsion systems and nuclear electric/nuclear thermal propulsion systems.

  12. Performance Measurement Analysis System

    1989-06-01

    The PMAS4.0 (Performance Measurement Analysis System) is a user-oriented system designed to track the cost and schedule performance of Department of Energy (DOE) major projects (MPs) and major system acquisitions (MSAs) reporting under DOE Order 5700.4A, Project Management System. PMAS4.0 provides for the analysis of performance measurement data produced from management control systems complying with the Federal Government''s Cost and Schedule Control Systems Criteria.

  13. System status display information

    NASA Technical Reports Server (NTRS)

    Summers, L. G.; Erickson, J. B.

    1984-01-01

    The system Status Display is an electronic display system which provides the flight crew with enhanced capabilities for monitoring and managing aircraft systems. Guidelines for the design of the electronic system displays were established. The technical approach involved the application of a system engineering approach to the design of candidate displays and the evaluation of a Hernative concepts by part-task simulation. The system engineering and selection of candidate displays are covered.

  14. Lightside Atmospheric Revitalization System

    NASA Technical Reports Server (NTRS)

    Colling, A. K.; Cushman, R. J.; Hultman, M. M.; Nason, J. R.

    1980-01-01

    The system was studied as a replacement to the present baseline LiOH system for extended duration shuttle missions. The system consists of three subsystems: a solid amine water desorbed regenerable carbon dioxide removal system, a water vapor electrolysis oxygen generating system, and a Sabatier reactor carbon dioxide reduction system. The system is designed for use on a solar powered shuttle vehicle. The majority of the system's power requirements are utilized on the Sun side of each orbit, when solar power is available.

  15. Control system design method

    DOEpatents

    Wilson, David G.; Robinett, III, Rush D.

    2012-02-21

    A control system design method and concomitant control system comprising representing a physical apparatus to be controlled as a Hamiltonian system, determining elements of the Hamiltonian system representation which are power generators, power dissipators, and power storage devices, analyzing stability and performance of the Hamiltonian system based on the results of the determining step and determining necessary and sufficient conditions for stability of the Hamiltonian system, creating a stable control system based on the results of the analyzing step, and employing the resulting control system to control the physical apparatus.

  16. Umbra's system representation.

    SciTech Connect

    McDonald, Michael James

    2005-07-01

    This document describes the Umbra System representation. Umbra System representation, initially developed in the spring of 2003, is implemented in Incr/Tcl using concepts borrowed from Carnegie Mellon University's Architecture Description Language (ADL) called Acme. In the spring of 2004 through January 2005, System was converted to Umbra 4, extended slightly, and adopted as the underlying software system for a variety of Umbra applications that support Complex Systems Engineering (CSE) and Complex Adaptive Systems Engineering (CASE). System is now a standard part Of Umbra 4. While Umbra 4 also includes an XML parser for System, the XML parser and Schema are not described in this document.

  17. Integrated Systems Health Management for Intelligent Systems

    NASA Technical Reports Server (NTRS)

    Figueroa, Fernando; Melcher, Kevin

    2011-01-01

    The implementation of an integrated system health management (ISHM) capability is fundamentally linked to the management of data, information, and knowledge (DIaK) with the purposeful objective of determining the health of a system. It is akin to having a team of experts who are all individually and collectively observing and analyzing a complex system, and communicating effectively with each other in order to arrive at an accurate and reliable assessment of its health. In this paper, concepts, procedures, and approaches are presented as a foundation for implementing an intelligent systems ]relevant ISHM capability. The capability stresses integration of DIaK from all elements of a system. Both ground-based (remote) and on-board ISHM capabilities are compared and contrasted. The information presented is the result of many years of research, development, and maturation of technologies, and of prototype implementations in operational systems.

  18. Systems engineering for very large systems

    NASA Technical Reports Server (NTRS)

    Lewkowicz, Paul E.

    1993-01-01

    Very large integrated systems have always posed special problems for engineers. Whether they are power generation systems, computer networks or space vehicles, whenever there are multiple interfaces, complex technologies or just demanding customers, the challenges are unique. 'Systems engineering' has evolved as a discipline in order to meet these challenges by providing a structured, top-down design and development methodology for the engineer. This paper attempts to define the general class of problems requiring the complete systems engineering treatment and to show how systems engineering can be utilized to improve customer satisfaction and profit ability. Specifically, this work will focus on a design methodology for the largest of systems, not necessarily in terms of physical size, but in terms of complexity and interconnectivity.

  19. Epilogue: Systems Approaches and Systems Practice

    NASA Astrophysics Data System (ADS)

    Reynolds, Martin; Holwell, Sue

    Each of the five systems approaches discussed in this volume: system dynamics (SD), the viable systems model (VSM), strategic options development and analysis (SODA), soft systems methodology (SSM) and critical systems heuristics (CSH) has a pedigree. Not in the sense of the sometimes absurd spectacle of animals paraded at dog shows. Rather, their pedigree derives from their systems foundations, their capacity to evolve and their flexibility in use. None of the five approaches has developed out of use in restricted and controlled contexts of either low or high levels of complicatedness. Neither has any one of them evolved as a consequence of being applied only to situations with either presumed stakeholder agreement on purpose, or courteous disagreement amongst stakeholders, or stakeholder coercion. The compilation is not a celebration of abstract ‘methodologies', but of theoretically robust approaches that have a genuine pedigree in practice.

  20. Expert system modeling of a vision system

    NASA Astrophysics Data System (ADS)

    Reihani, Kamran; Thompson, Wiley E.

    1992-05-01

    The proposed artificial intelligence-based vision model incorporates natural recognition processes depicted as a visual pyramid and hierarchical representation of objects in the database. The visual pyramid, with based and apex representing pixels and image, respectively, is used as an analogy for a vision system. This paper provides an overview of recognition activities and states in the framework of an inductive model. Also, it presents a natural vision system and a counterpart expert system model that incorporates the described operations.

  1. INSENS sensor system

    SciTech Connect

    Myers, D.W.; Baker, J.; Benzel, D.M.; Fuess, D.A.

    1993-09-29

    This paper describes an unattended ground sensor system that has been developed for the immigration and Naturalization Service (INS). The system, known as INSENS, was developed at the Lawrence Livermore National Laboratory for use by the United States Border Patrol. This system assists in the detection of illegal entry of aliens and contraband (illegal drugs, etc.) into the United States along its land borders. Key to the system is its flexible modular design which allows future software and hardware enhancements to the system without altering the fundamental architecture of the system. Elements of the system include a sensor system capable of processing signals from multiple directional probes, a repeater system, and a handheld monitor system. Seismic, passive infrared (PIR), and magnetic probes are currently supported. The design of the INSENS system elements and their performance are described.

  2. Precision digital control systems

    NASA Astrophysics Data System (ADS)

    Vyskub, V. G.; Rozov, B. S.; Savelev, V. I.

    This book is concerned with the characteristics of digital control systems of great accuracy. A classification of such systems is considered along with aspects of stabilization, programmable control applications, digital tracking systems and servomechanisms, and precision systems for the control of a scanning laser beam. Other topics explored are related to systems of proportional control, linear devices and methods for increasing precision, approaches for further decreasing the response time in the case of high-speed operation, possibilities for the implementation of a logical control law, and methods for the study of precision digital control systems. A description is presented of precision automatic control systems which make use of electronic computers, taking into account the existing possibilities for an employment of computers in automatic control systems, approaches and studies required for including a computer in such control systems, and an analysis of the structure of automatic control systems with computers. Attention is also given to functional blocks in the considered systems.

  3. Forming different planetary systems

    NASA Astrophysics Data System (ADS)

    Zhou, Ji-Lin; Xie, Ji-Wei; Liu, Hui-Gen; Zhang, Hui; Sun, Yi-Sui

    2012-08-01

    With the increasing number of detected exoplanet samples, the statistical properties of planetary systems have become much clearer. In this review, we summarize the major statistical results that have been revealed mainly by radial velocity and transiting observations, and try to interpret them within the scope of the classical core-accretion scenario of planet formation, especially in the formation of different orbital architectures for planetary systems around main sequence stars. Based on the different possible formation routes for different planet systems, we tentatively classify them into three major catalogs: hot Jupiter systems, standard systems and distant giant planet systems. The standard system can be further categorized into three sub-types under different circumstances: solar-like systems, hot Super-Earth systems, and subgiant planet systems. We also review the theory of planet detection and formation in binary systems as well as planets in star clusters.

  4. Hot Spot Removal System: System description

    SciTech Connect

    1997-09-01

    Hazardous wastes contaminated with radionuclides, chemicals, and explosives exist across the Department of Energy complex and need to be remediated due to environmental concerns. Currently, an opportunity is being developed to dramatically reduce remediation costs and to assist in the acceleration of schedules associated with these wastes by deploying a Hot Spot Removal System. Removing the hot spot from the waste site will remove risk driver(s) and enable another, more cost effective process/option/remedial alternative (i.e., capping) to be applied to the remainder of the site. The Hot Spot Removal System consists of a suite of technologies that will be utilized to locate and remove source terms. Components of the system can also be used in a variety of other cleanup activities. This Hot Spot Removal System Description document presents technologies that were considered for possible inclusion in the Hot Spot Removal System, technologies made available to the Hot Spot Removal System, industrial interest in the Hot Spot Removal System`s subsystems, the schedule required for the Hot Spot Removal System, the evaluation of the relevant technologies, and the recommendations for equipment and technologies as stated in the Plan section.

  5. Space Launch and Temperature System: Avionics System

    NASA Technical Reports Server (NTRS)

    Gillis, Amelia; Luna, Steve; Schrock, Ken; Howard, Ricky; Kilpatrick, John (Technical Monitor)

    2001-01-01

    This paper outlines the approach needed to develop the avionics system for a Space Launch and Transportation System. Avionics systems development, power, range safety, and simulations considerations are covered. Each of these topics includes the project design inputs that must be considered on the outset. Process steps are then provided to obtain the desired outputs. This paper discusses the importance of starting and staying with an overall systems plan that ensures that all avionics internal and external requirements are fulfilled. Key design, development, testing and implementations considerations are provided.

  6. Novel central nervous system drug delivery systems.

    PubMed

    Stockwell, Jocelyn; Abdi, Nabiha; Lu, Xiaofan; Maheshwari, Oshin; Taghibiglou, Changiz

    2014-05-01

    For decades, biomedical and pharmaceutical researchers have worked to devise new and more effective therapeutics to treat diseases affecting the central nervous system. The blood-brain barrier effectively protects the brain, but poses a profound challenge to drug delivery across this barrier. Many traditional drugs cannot cross the blood-brain barrier in appreciable concentrations, with less than 1% of most drugs reaching the central nervous system, leading to a lack of available treatments for many central nervous system diseases, such as stroke, neurodegenerative disorders, and brain tumors. Due to the ineffective nature of most treatments for central nervous system disorders, the development of novel drug delivery systems is an area of great interest and active research. Multiple novel strategies show promise for effective central nervous system drug delivery, giving potential for more effective and safer therapies in the future. This review outlines several novel drug delivery techniques, including intranasal drug delivery, nanoparticles, drug modifications, convection-enhanced infusion, and ultrasound-mediated drug delivery. It also assesses possible clinical applications, limitations, and examples of current clinical and preclinical research for each of these drug delivery approaches. Improved central nervous system drug delivery is extremely important and will allow for improved treatment of central nervous system diseases, causing improved therapies for those who are affected by central nervous system diseases. PMID:24325540

  7. Intelligent inspection system

    NASA Astrophysics Data System (ADS)

    May, Jeniece; Dale, Ken; Holloway, Mike; Gaby, Willard

    1997-01-01

    The intelligent inspection system is an advanced controller and analysis system for dimensional measuring machines dedicated to measuring surface of revolution mechanical parts. IIS was developed by the Lockheed Martin Energy Systems, Inc. Oak Ridge Y-12 plant because no commercial product was available to replace the obsolete computing systems on these important machines.

  8. Coaches as System Leaders

    ERIC Educational Resources Information Center

    Fullan, Michael; Knight, Jim

    2011-01-01

    The role of school leadership--of principals and coaches--must be played out on a systems level to get widespread and sustainable improvement. Successful, whole-system education reform relies on capacity building, teamwork, pedagogy, and systemic reform. The strategies of good coaches and the right drivers for whole-system reform go hand in hand.…

  9. Computer Center: CIBE Systems.

    ERIC Educational Resources Information Center

    Crovello, Theodore J.

    1982-01-01

    Differentiates between computer systems and Computers in Biological Education (CIBE) systems (computer system intended for use in biological education). Describes several CIBE stand alone systems: single-user microcomputer; single-user microcomputer/video-disc; multiuser microcomputers; multiuser maxicomputer; and local and long distance computer…

  10. Program (systems) engineering

    NASA Technical Reports Server (NTRS)

    Baroff, Lynn E.; Easter, Robert W.; Pomphrey, Richard B.

    2004-01-01

    Program Systems Engineering applies the principles of Systems Engineering at the program level. Space programs are composed of interrelated elements which can include collections of projects, advanced technologies, information systems, etc. Some program elements are outside traditional engineering's physical systems, such as education and public outreach, public relations, resource flow, and interactions within the political environments.

  11. Imaging systems and applications.

    PubMed

    Bennett, Gisele; Catrysse, Peter B; Farrell, Joyce E; Fowler, Boyd; Mait, Joseph N

    2012-02-01

    Imaging systems are used in consumer, medical, and military applications. Designing, developing, and building imaging systems requires a multidisciplinary approach. This issue features current research in imaging systems that ranges from fundamental theories to novel applications. Although the papers collected are diverse, their unique compilation provides a systems perspective to imaging. PMID:22307134

  12. Broad Bandwidth Telecommunications Systems.

    ERIC Educational Resources Information Center

    Sodolski, John

    Broad bandwidth transmission systems have been around for years. They include microwave, assorted cable systems, and recently, satellites. With the exception of some privately owned systems, broadband services have been furnished by the common carriers. Recently, a new element has been added--Cable Antenna Television (CATV) distribution systems.…

  13. Microsphere insulation systems

    NASA Technical Reports Server (NTRS)

    Allen, Mark S. (Inventor); Willen, Gary S. (Inventor); Mohling, Robert A. (Inventor)

    2005-01-01

    A new insulation system is provided that contains microspheres. This insulation system can be used to provide insulated panels and clamshells, and to insulate annular spaces around objects used to transfer, store, or transport cryogens and other temperature-sensitive materials. This insulation system provides better performance with reduced maintenance than current insulation systems.

  14. Medical imaging systems

    DOEpatents

    Frangioni, John V

    2013-06-25

    A medical imaging system provides simultaneous rendering of visible light and diagnostic or functional images. The system may be portable, and may include adapters for connecting various light sources and cameras in open surgical environments or laparascopic or endoscopic environments. A user interface provides control over the functionality of the integrated imaging system. In one embodiment, the system provides a tool for surgical pathology.

  15. Electronic Document Supply Systems.

    ERIC Educational Resources Information Center

    Cawkell, A. E.

    1991-01-01

    Describes electronic document delivery systems used by libraries and document image processing systems used for business purposes. Topics discussed include technical specifications; analogue read-only laser videodiscs; compact discs and CD-ROM; WORM; facsimile; ADONIS (Article Delivery over Network Information System); DOCDEL; and systems at the…

  16. Identification of propulsion systems

    NASA Technical Reports Server (NTRS)

    Merrill, Walter; Guo, Ten-Huei; Duyar, Ahmet

    1991-01-01

    This paper presents a tutorial on the use of model identification techniques for the identification of propulsion system models. These models are important for control design, simulation, parameter estimation, and fault detection. Propulsion system identification is defined in the context of the classical description of identification as a four step process that is unique because of special considerations of data and error sources. Propulsion system models are described along with the dependence of system operation on the environment. Propulsion system simulation approaches are discussed as well as approaches to propulsion system identification with examples for both air breathing and rocket systems.

  17. On generalized Volterra systems

    NASA Astrophysics Data System (ADS)

    Charalambides, S. A.; Damianou, P. A.; Evripidou, C. A.

    2015-01-01

    We construct a large family of evidently integrable Hamiltonian systems which are generalizations of the KM system. The algorithm uses the root system of a complex simple Lie algebra. The Hamiltonian vector field is homogeneous cubic but in a number of cases a simple change of variables transforms such a system to a quadratic Lotka-Volterra system. We present in detail all such systems in the cases of A3, A4 and we also give some examples from higher dimensions. We classify all possible Lotka-Volterra systems that arise via this algorithm in the An case.

  18. What is systems engineering?

    SciTech Connect

    Bahill, A.T.

    1995-08-01

    Systems Engineering is an interdisciplinary process that ensures that the customers` needs are satisfied throughout a system`s entire life cycle. This process includes: understanding customer needs; stating the problem; specifying requirements; defining performance and cost measures, prescribing tests, validating requirements, conducting design reviews, exploring alternative concepts, sensitivity analyses, functional decomposition, system design, designing and managing interfaces, system integration, total system test, configuration management, risk management, reliability analysis; total quality management; project management; and documentation. Material for this paper was gathered from senior Systems Engineers at Sandia National Laboratories.

  19. Advanced information processing system: Local system services

    NASA Technical Reports Server (NTRS)

    Burkhardt, Laura; Alger, Linda; Whittredge, Roy; Stasiowski, Peter

    1989-01-01

    The Advanced Information Processing System (AIPS) is a multi-computer architecture composed of hardware and software building blocks that can be configured to meet a broad range of application requirements. The hardware building blocks are fault-tolerant, general-purpose computers, fault-and damage-tolerant networks (both computer and input/output), and interfaces between the networks and the computers. The software building blocks are the major software functions: local system services, input/output, system services, inter-computer system services, and the system manager. The foundation of the local system services is an operating system with the functions required for a traditional real-time multi-tasking computer, such as task scheduling, inter-task communication, memory management, interrupt handling, and time maintenance. Resting on this foundation are the redundancy management functions necessary in a redundant computer and the status reporting functions required for an operator interface. The functional requirements, functional design and detailed specifications for all the local system services are documented.

  20. Decentralized Modular Systems Versus Centralized Systems.

    ERIC Educational Resources Information Center

    Crossey, R. E.

    Building design, planning, and construction programing for modular decentralized mechanical building systems are outlined in terms of costs, performance, expansion and flexibility. Design strategy, approach, and guidelines for implementing such systems for buildings are suggested, with emphasis on mechanical equipment and building element…

  1. ENVIRONMENTAL SYSTEMS MANAGEMENT AND SUSTAINABLE SYSTEMS THEORY

    EPA Science Inventory

    Environmental Systems Management is the management of environmental problems at the systems level fully accounting for the multi-dimensional nature of the environment. This includes socio-economic dimensions as well as the usual physical and life science aspects. This is importa...

  2. Performance, Performance System, and High Performance System

    ERIC Educational Resources Information Center

    Jang, Hwan Young

    2009-01-01

    This article proposes needed transitions in the field of human performance technology. The following three transitions are discussed: transitioning from training to performance, transitioning from performance to performance system, and transitioning from learning organization to high performance system. A proposed framework that comprises…

  3. EPICS system: system structure and user interface

    SciTech Connect

    West, R.E.; Bartlett, J.F.; Bobbitt, J.S.; Lahey, T.E.; Kramper, B.J.; MacKinnon, B.A.

    1984-02-01

    This paper present the user's view of and the general organization of the EPICS control system at Fermilab. Various subsystems of the EPICS control system are discussed. These include the user command language, software protection, the device database, remote computer interfaces, and several application utilities. This paper is related to two other papers on EPICS: an overview paper and a detailed implementation paper.

  4. Efficient Evaluation System for Learning Management Systems

    ERIC Educational Resources Information Center

    Cavus, Nadire

    2009-01-01

    A learning management system (LMS) provides the platform for web-based learning environment by enabling the management, delivery, tracking of learning, testing, communication, registration process and scheduling. There are many LMS systems on the market that can be obtained for free or through payment. It has now become an important task to choose…

  5. Local hospital systems: forerunners of regional systems?

    PubMed

    Luke, R D

    1992-01-01

    Over the past several decades, the hospital industry has been undergoing a major organizational change that has until now been little examined. Local hospital systems (LHSs) are combinations of two or more hospitals that are in the same company and located in or around the same metropolitan areas in this country. This article presents the first detailed examination of the 402 such systems that have been identified to date. LHSs offer great potential for achieving the cost, quality, and access benefits that are often attributable to regional systems. The degree to which LHSs have attained some basic structural features expected of regional systems are examined. Differences are compared within ownership categories. Issues and challenges facing leaders in the field, should they hope to achieve the potential of regional systems, are discussed. PMID:10122669

  6. Photovoltaic systems and applications

    SciTech Connect

    Not Available

    1982-01-01

    Abstracts are given of presentations given at a project review meeting held at Albuquerque, NM. The proceedings cover the past accomplishments and current activities of the Photovoltaic Systems Research, Balance-of-System Technology Development and System Application Experiments Projects at Sandia National Laboratories. The status of intermediate system application experiments and residential system analysis is emphasized. Some discussion of the future of the Photovoltaic Program in general, and the Sandia projects in particular is also presented.

  7. Residential photovoltaic system designs

    SciTech Connect

    Russell, M. C.

    1981-01-01

    A project to develop Residential Photovoltaic Systems has begun at Massachusetts Institute of Technology Lincoln Laboratory with the construction and testing of five Prototype Systems. All of these systems utilize a roof-mounted photovoltaic array and allow excess solar-generated electric energy to be fed back to the local utility grid, eliminating the need for on-site storage. Residential photovoltaic system design issues are discussed and specific features of the five Prototype Systems now under test are presented.

  8. Satellite services system overview

    NASA Technical Reports Server (NTRS)

    Rysavy, G.

    1982-01-01

    The benefits of a satellite services system and the basic needs of the Space Transportation System to have improved satellite service capability are identified. Specific required servicing equipment are discussed in terms of their technology development status and their operative functions. Concepts include maneuverable television systems, extravehicular maneuvering unit, orbiter exterior lighting, satellite holding and positioning aid, fluid transfer equipment, end effectors for the remote manipulator system, teleoperator maneuvering system, and hand and power tools.

  9. Data Acquisition Systems

    NASA Technical Reports Server (NTRS)

    1989-01-01

    Technology developed during a joint research program with Langley and Kinetic Systems Corporation led to Kinetic Systems' production of a high speed Computer Automated Measurement and Control (CAMAC) data acquisition system. The study, which involved the use of CAMAC equipment applied to flight simulation, significantly improved the company's technical capability and produced new applications. With Digital Equipment Corporation, Kinetic Systems is marketing the system to government and private companies for flight simulation, fusion research, turbine testing, steelmaking, etc.

  10. FNAL system patching design

    SciTech Connect

    Schmidt, Jack; Lilianstrom, Al; Romero, Andy; Dawson, Troy; Sieh, Connie; /Fermilab

    2004-01-01

    FNAL has over 5000 PCs running either Linux or Windows software. Protecting these systems efficiently against the latest vulnerabilities that arise has prompted FNAL to take a more central approach to patching systems. Due to different levels of existing support infrastructures, the patching solution for linux systems differs from that of windows systems. In either case, systems are checked for vulnerabilities by Computer Security using the Nessus tool.

  11. Fluid infusion system

    NASA Technical Reports Server (NTRS)

    1974-01-01

    Performance testing carried out in the development of the prototype zero-g fluid infusion system is described and summarized. Engineering tests were performed in the course of development, both on the original breadboard device and on the prototype system. This testing was aimed at establishing baseline system performance parameters and facilitating improvements. Acceptance testing was then performed on the prototype system to verify functional performance. Acceptance testing included a demonstration of the fluid infusion system on a laboratory animal.

  12. Automated Pilot Advisory System

    NASA Technical Reports Server (NTRS)

    Parks, J. L., Jr.; Haidt, J. G.

    1981-01-01

    An Automated Pilot Advisory System (APAS) was developed and operationally tested to demonstrate the concept that low cost automated systems can provide air traffic and aviation weather advisory information at high density uncontrolled airports. The system was designed to enhance the see and be seen rule of flight, and pilots who used the system preferred it over the self announcement system presently used at uncontrolled airports.

  13. Evolvable synthetic neural system

    NASA Technical Reports Server (NTRS)

    Curtis, Steven A. (Inventor)

    2009-01-01

    An evolvable synthetic neural system includes an evolvable neural interface operably coupled to at least one neural basis function. Each neural basis function includes an evolvable neural interface operably coupled to a heuristic neural system to perform high-level functions and an autonomic neural system to perform low-level functions. In some embodiments, the evolvable synthetic neural system is operably coupled to one or more evolvable synthetic neural systems in a hierarchy.

  14. On evolutionary systems.

    PubMed

    Alvarez de Lorenzana, J M; Ward, L M

    1987-01-01

    This paper develops a metatheoretical framework for understanding evolutionary systems (systems that develop in ways that increase their own variety). The framework addresses shortcomings seen in other popular systems theories. It concerns both living and nonliving systems, and proposes a metahierarchy of hierarchical systems. Thus, it potentially addresses systems at all descriptive levels. We restrict our definition of system to that of a core system whose parts have a different ontological status than the system, and characterize the core system in terms of five global properties: minimal length interval, minimal time interval, system cycle, total receptive capacity, and system potential. We propose two principles through the interaction of which evolutionary systems develop. The Principle of Combinatorial Expansion describes how a core system realizes its developmental potential through a process of progressive differentiation of the single primal state up to a limit stage. The Principle of Generative Condensation describes how the components of the last stage of combinatorial expansion condense and become the environment for and components of new, enriched systems. The early evolution of the Universe after the "big bang" is discussed in light of these ideas as an example of the application of the framework. PMID:3689299

  15. A System of Systems Approach to the EU Energy System

    NASA Astrophysics Data System (ADS)

    Jess, Tom; Madani, Kaveh; Mahlooji, Maral; Ristic, Bora

    2016-04-01

    Around the world, measures to prevent dangerous climate change are being adopted and may change energy systems fundamentally. The European Union (EU) is committed to reducing greenhouse gas emission by 20% by 2020 and by 80-95% by 2050. In order to achieve this, EU member states aim to increase the share of renewables in the energy mix to 20% by 2020. This commitment comes as part of a series of other aims, principles, and policies to reform the EU's energy system. Cost-efficiency in the emissions reductions measures as well as strategic goals under the Resource Efficient Europe flagship initiative which would include a more prudent approach to other natural resources such as water and land. Using the "System of Systems Approach", as from Hadian and Madani (2015), energy sources' Relative Aggregate Footprints (RAF) in the EU are evaluated. RAF aggregates across four criteria: carbon footprint, water footprint, land footprint, and economic cost. The four criteria are weighted by resource availability across the EU and for each Member State. This provides an evaluation of the overall resource use efficiency of the EU's energy portfolio and gives insight into the differences in the desirability of energy sources across Member States. Broadly, nuclear, onshore wind, and geothermal are most desirable under equal criteria weights and EU average weighting introduces only small changes in the relative performance of only few technologies. The member state specific weightings show that most countries have similar energy technology preferences. However, the UK deviates most strongly from the average, with an even stronger preference for nuclear and coal. Sweden, Malta and Finland also deviate from the typical preferences indicating the complexity in play in reforming the EU energy system. Reference Hadian S, Madani K (2015) A System of Systems Approach to Energy Sustainability Assessment: Are All Renewables Really Green? Ecological Indicators, 52, 194-206.

  16. Dynamometer Testing of a NW2200 Drivetrain: Cooperative Research and Development Final Report, CRADA Number CRD-10-394

    SciTech Connect

    Wallen, R.

    2012-04-01

    Northern Power Systems specializes in direct drive wind turbine designs. CRADA CRD-10-394 involved testing the NW2200 wind turbine power train. Power train testing is important because it allows validation of the generator design and some control algorithms prior to installation on a tower, where this data would be more difficult and time consuming to collect. In an effort to keep the commercial product schedule on time, Northern Power requested testing support from the National Renewable Energy Laboratory for this testing. The test program was performed using NREL's 2.5 MW dynamometer test bed at the National Wind Technology Center near Boulder, CO.

  17. Intelligent systems technology infrastructure for integrated systems

    NASA Technical Reports Server (NTRS)

    Lum, Henry

    1991-01-01

    A system infrastructure must be properly designed and integrated from the conceptual development phase to accommodate evolutionary intelligent technologies. Several technology development activities were identified that may have application to rendezvous and capture systems. Optical correlators in conjunction with fuzzy logic control might be used for the identification, tracking, and capture of either cooperative or non-cooperative targets without the intensive computational requirements associated with vision processing. A hybrid digital/analog system was developed and tested with a robotic arm. An aircraft refueling application demonstration is planned within two years. Initially this demonstration will be ground based with a follow-on air based demonstration. System dependability measurement and modeling techniques are being developed for fault management applications. This involves usage of incremental solution/evaluation techniques and modularized systems to facilitate reuse and to take advantage of natural partitions in system models. Though not yet commercially available and currently subject to accuracy limitations, technology is being developed to perform optical matrix operations to enhance computational speed. Optical terrain recognition using camera image sequencing processed with optical correlators is being developed to determine position and velocity in support of lander guidance. The system is planned for testing in conjunction with Dryden Flight Research Facility. Advanced architecture technology is defining open architecture design constraints, test bed concepts (processors, multiple hardware/software and multi-dimensional user support, knowledge/tool sharing infrastructure), and software engineering interface issues.

  18. Systems Architecture for a Nationwide Healthcare System.

    PubMed

    Abin, Jorge; Nemeth, Horacio; Friedmann, Ignacio

    2015-01-01

    From a national level to give Internet technology support, the Nationwide Integrated Healthcare System in Uruguay requires a model of Information Systems Architecture. This system has multiple healthcare providers (public and private), and a strong component of supplementary services. Thus, the data processing system should have an architecture that considers this fact, while integrating the central services provided by the Ministry of Public Health. The national electronic health record, as well as other related data processing systems, should be based on this architecture. The architecture model described here conceptualizes a federated framework of electronic health record systems, according to the IHE affinity model, HL7 standards, local standards on interoperability and security, as well as technical advice provided by AGESIC. It is the outcome of the research done by AGESIC and Systems Integration Laboratory (LINS) on the development and use of the e-Government Platform since 2008, as well as the research done by the team Salud.uy since 2013. PMID:26262000

  19. Modeling Power Systems as Complex Adaptive Systems

    SciTech Connect

    Chassin, David P.; Malard, Joel M.; Posse, Christian; Gangopadhyaya, Asim; Lu, Ning; Katipamula, Srinivas; Mallow, J V.

    2004-12-30

    Physical analogs have shown considerable promise for understanding the behavior of complex adaptive systems, including macroeconomics, biological systems, social networks, and electric power markets. Many of today's most challenging technical and policy questions can be reduced to a distributed economic control problem. Indeed, economically based control of large-scale systems is founded on the conjecture that the price-based regulation (e.g., auctions, markets) results in an optimal allocation of resources and emergent optimal system control. This report explores the state-of-the-art physical analogs for understanding the behavior of some econophysical systems and deriving stable and robust control strategies for using them. We review and discuss applications of some analytic methods based on a thermodynamic metaphor, according to which the interplay between system entropy and conservation laws gives rise to intuitive and governing global properties of complex systems that cannot be otherwise understood. We apply these methods to the question of how power markets can be expected to behave under a variety of conditions.

  20. Rover waste assay system

    SciTech Connect

    Akers, D.W.; Stoots, C.M.; Kraft, N.C.; Marts, D.J.

    1997-11-01

    The Rover Waste Assay System (RWAS) is a nondestructive assay system designed for the rapid assay of highly-enriched {sup 235}U contaminated piping, tank sections, and debris from the Rover nuclear rocket fuel processing facility at the Idaho Chemical Processing Plant. A scanning system translates a NaI(Tl) detector/collimator system over the structural components where both relative and calibrated measurements for {sup 137}Cs are made. Uranium-235 concentrations are in operation and is sufficiently automated that most functions are performed by the computer system. These functions include system calibration, problem identification, collimator control, data analysis, and reporting. Calibration of the system was done through a combination of measurements on calibration standards and benchmarked modeling. A description of the system is presented along with the methods and uncertainties associated with the calibration and analysis of the system for components from the Rover facility. 4 refs., 2 figs., 4 tabs.

  1. NASA Systems Engineering Handbook

    NASA Technical Reports Server (NTRS)

    Shishko, Robert; Aster, Robert; Chamberlain, Robert G.; Mcduffee, Patrick; Pieniazek, Les; Rowell, Tom; Bain, Beth; Cox, Renee I.; Mooz, Harold; Polaski, Lou

    1995-01-01

    This handbook brings the fundamental concepts and techniques of systems engineering to NASA personnel in a way that recognizes the nature of NASA systems and environment. It is intended to accompany formal NASA training courses on systems engineering and project management when appropriate, and is designed to be a top-level overview. The concepts were drawn from NASA field center handbooks, NMI's/NHB's, the work of the NASA-wide Systems Engineering Working Group and the Systems Engineering Process Improvement Task team, several non-NASA textbooks and guides, and material from independent systems engineering courses taught to NASA personnel. Five core chapters cover systems engineering fundamentals, the NASA Project Cycle, management issues in systems engineering, systems analysis and modeling, and specialty engineering integration. It is not intended as a directive. Superseded by: NASA/SP-2007-6105 Rev 1 (20080008301).

  2. Alkaline etch system qualification

    SciTech Connect

    Goldammer, S.E.; Pemberton, S.E.; Tucker, D.R.

    1997-04-01

    Based on the data from this qualification activity, the Atotech etch system, even with minimum characterization, was capable of etching production printed circuit products as good as those from the Chemcut system. Further characterization of the Atotech system will improve its etching capability. In addition to the improved etch quality expected from further characterization, the Atotech etch system has additional features that help reduce waste and provide for better consistency in the etching process. The programmable logic controller and computer will allow operators to operate the system manually or from pre-established recipes. The evidence and capabilities of the Atotech system made it as good as or better than the Chemcut system for etching WR products. The Printed Wiring Board Engineering Department recommended that the Atotech system be released for production. In December 1995, the Atotech system was formerly qualified for production.

  3. Open systems storage platforms

    NASA Technical Reports Server (NTRS)

    Collins, Kirby

    1992-01-01

    The building blocks for an open storage system includes a system platform, a selection of storage devices and interfaces, system software, and storage applications CONVEX storage systems are based on the DS Series Data Server systems. These systems are a variant of the C3200 supercomputer with expanded I/O capabilities. These systems support a variety of medium and high speed interfaces to networks and peripherals. System software is provided in the form of ConvexOS, a POSIX compliant derivative of 4.3BSD UNIX. Storage applications include products such as UNITREE and EMASS. With the DS Series of storage systems, Convex has developed a set of products which provide open system solutions for storage management applications. The systems are highly modular, assembled from off the shelf components with industry standard interfaces. The C Series system architecture provides a stable base, with the performance and reliability of a general purpose platform. This combination of a proven system architecture with a variety of choices in peripherals and application software allows wide flexibility in configurations, and delivers the benefits of open systems to the mass storage world.

  4. A systems analysis of longwall mining systems

    SciTech Connect

    Ramani, R.V.; Kovach, T.S.

    1983-03-01

    In many instances, the actual production from a longwall face does not equal the planned capacity. General problem areas which have been identified include face length and panel depth, face area and gate entry roof support, face conveyor and shearer wear, outby haulage system failures, number of entries in longwall gate development and longwall move time. The performance of a longwall face is totally dependent on the interaction of these and many other factors. To explore fully these interactions, a systems analysis of longwalls has been performed. In this paper, the systems approach, the factors considered in the analysis, and the results of the analysis are presented.

  5. Effects of 18-week in-season heavy-resistance and power training on throwing velocity, strength, jumping, and maximal sprint swim performance of elite male water polo players.

    PubMed

    Ramos Veliz, Rafael; Requena, Bernardo; Suarez-Arrones, Luis; Newton, Robert U; Sáez de Villarreal, Eduardo

    2014-04-01

    We examined the effects of 18 weeks of strength and high-intensity training on key sport performance measures of elite male water polo (WP) players. Twenty-seven players were randomly assigned to 2 groups, control (in-water training only) and strength group, (strength training sessions [twice per week] + in-water training). In-water training was conducted 5 d·wk. Twenty-meter maximal sprint swim, maximal dynamic strength 1-repetition maximum (1RM) for upper bench press (BP) and lower full squat (FS) body, countermovement jump (CMJ), and throwing velocity were measured before and after the training. The training program included upper and lower body strength and high-intensity exercises (BP, FS, military press, pull-ups, CMJ loaded, and abs). Baseline-training results showed no significant differences between the groups in any of the variables tested. No improvement was found in the control group; however, meaningful improvement was found in all variables in the experimental group: CMJ (2.38 cm, 6.9%, effect size [ES] = 0.48), BP (9.06 kg, 10.53%, ES = 0.66), FS (11.06 kg, 14.21%, ES = 0.67), throwing velocity (1.76 km·h(-1), 2.76%, ES = 0.25), and 20-m maximal sprint swim (-0.26 seconds, 2.25%, ES = 0.29). Specific strength and high-intensity training in male WP players for 18 weeks produced a positive effect on performance qualities highly specific to WP. Therefore, we propose modifications to the current training methodology for WP players to include strength and high-intensity training for athlete preparation in this sport. PMID:24077370

  6. Digital wireless control system

    NASA Astrophysics Data System (ADS)

    Smith, R.

    1993-08-01

    The Digital Wireless Control System (DWCS) is designed to initiate high explosives safely while using a wireless remote control system. Numerous safety features have been designed into the fire control system to mitigate the hazards associated with remote initiation of high explosives. These safety features range from a telemetry (TM) fire control status system to mechanical timers and keyed power lockout switches. The environment, safety, and health (ES&H) Standard Operating Procedure (SOP) SP471970 is intended as a guide when working with the DWCS. This report describes the Digital Wireless Control System and outlines each component's theory of operation and its relationship to the system.

  7. Continuous system modeling

    NASA Technical Reports Server (NTRS)

    Cellier, Francois E.

    1991-01-01

    A comprehensive and systematic introduction is presented for the concepts associated with 'modeling', involving the transition from a physical system down to an abstract description of that system in the form of a set of differential and/or difference equations, and basing its treatment of modeling on the mathematics of dynamical systems. Attention is given to the principles of passive electrical circuit modeling, planar mechanical systems modeling, hierarchical modular modeling of continuous systems, and bond-graph modeling. Also discussed are modeling in equilibrium thermodynamics, population dynamics, and system dynamics, inductive reasoning, artificial neural networks, and automated model synthesis.

  8. Flash evaporator systems test

    NASA Technical Reports Server (NTRS)

    Dietz, J. B.

    1976-01-01

    A flash evaporator heat rejection system representative of that proposed for the space shuttle orbiter underwent extensive system testing at the NASA Johnson Space Center (JSC) to determine its operational suitability and to establish system performance/operational characteristics for use in the shuttle system. During the tests the evaporator system demonstrated its suitability to meet the shuttle requirements by: (1) efficient operation with 90 to 95% water evaporation efficiency, (2) control of outlet temperature to 40 + or - 2 F for partial heat load operation, (3) stability of control system for rapid changes in Freon inlet temperature, and (4) repeated dormant-to-active device operation without any startup procedures.

  9. Space shuttle avionics system

    NASA Technical Reports Server (NTRS)

    Hanaway, John F.; Moorehead, Robert W.

    1989-01-01

    The Space Shuttle avionics system, which was conceived in the early 1970's and became operational in the 1980's represents a significant advancement of avionics system technology in the areas of systems and redundacy management, digital data base technology, flight software, flight control integration, digital fly-by-wire technology, crew display interface, and operational concepts. The origins and the evolution of the system are traced; the requirements, the constraints, and other factors which led to the final configuration are outlined; and the functional operation of the system is described. An overall system block diagram is included.

  10. Concepts, states, and systems

    NASA Astrophysics Data System (ADS)

    Wolff, Karl Erich

    2000-05-01

    Mathematical System Theory is extended to Conceptual System Theory using Formal Concept Analysis (Wille 1982). States are defined as formal concepts and `points of time' are generalized to `time granules,' interpreted as `pieces' of time needed for the realization of measurements. As a generalization of classical time systems we define conceptual time systems, their state spaces and phase spaces. Time dependent relations among the parts of a conceptual time system are introduced in `relational conceptual time systems.' Applications in psychology and industry, including `conceptual films' are mentioned.

  11. Cooperating systems: Layered MAS

    NASA Technical Reports Server (NTRS)

    Rochowiak, Daniel

    1990-01-01

    Distributed intelligent systems can be distinguished by the models that they use. The model developed focuses on layered multiagent system conceived of as a bureaucracy in which a distributed data base serves as a central means of communication. The various generic bureaus of such a system is described and a basic vocabulary for such systems is presented. In presenting the bureaus and vocabularies, special attention is given to the sorts of reasonings that are appropriate. A bureaucratic model has a hierarchy of master system and work group that organizes E agents and B agents. The master system provides the administrative services and support facilities for the work groups.

  12. Data Acquisition Systems

    NASA Technical Reports Server (NTRS)

    1994-01-01

    In the mid-1980s, Kinetic Systems and Langley Research Center determined that high speed CAMAC (Computer Automated Measurement and Control) data acquisition systems could significantly improve Langley's ARTS (Advanced Real Time Simulation) system. The ARTS system supports flight simulation R&D, and the CAMAC equipment allowed 32 high performance simulators to be controlled by centrally located host computers. This technology broadened Kinetic Systems' capabilities and led to several commercial applications. One of them is General Atomics' fusion research program. Kinetic Systems equipment allows tokamak data to be acquired four to 15 times more rapidly. Ford Motor company uses the same technology to control and monitor transmission testing facilities.

  13. Experiment support system

    NASA Technical Reports Server (NTRS)

    Shannon, A. V.

    1977-01-01

    The Experiment Support System is a switchboard system with displays and controls. It routes electrical power to experiments M092, M093, and M171 equipment; gaseous nitrogen to the Blood Pressure Measurement System; receives biomedical data from all related equipment; routes the conditioned data signals to the Airlock Module Telemetry System and also displays (in digital or analog from) portions of that data which the crewmen must see to complete the experiment successfully. The Experiment Support System is interfaced to the M131 control panel to transfer conditioned data to the Airlock Module Telemetry System.

  14. MLS: Airplane system modeling

    NASA Technical Reports Server (NTRS)

    Thompson, A. D.; Stapleton, B. P.; Walen, D. B.; Rieder, P. F.; Moss, D. G.

    1981-01-01

    Analysis, modeling, and simulations were conducted as part of a multiyear investigation of the more important airplane-system-related items of the microwave landing system (MLS). Particular emphasis was placed upon the airplane RF system, including the antenna radiation distribution, the cabling options from the antenna to the receiver, and the overall impact of the airborne system gains and losses upon the direct-path signal structure. In addition, effort was expended toward determining the impact of the MLS upon the airplane flight management system and developing the initial stages of a fast-time MLS automatic control system simulation model. Results ot these studies are presented.

  15. EPICS system: an overview

    SciTech Connect

    Bartlett, J.F.; Bobbitt, J.S.; Kramper, B.J.; Lahey, T.E.; MacKinnon, B.A.; West, R.E.

    1984-02-01

    This paper presents an overview of the EPICS control system at FERMILAB. EPICS is a distributed, multi-user, interactive system for the control and monitoring of particle beamlines at a high-energy experimental physics laboratory. The overview discusses the operating environment of the control system, the requirements which determined the design decisions, the hardware and software configurations, and plans for the future growth and enhancement of the present system. This paper is the first of three related papers on the EPICS system. The other two cover (1) the system structure and user interface and (2) RSX implementation issues.

  16. Verification of Adaptive Systems

    SciTech Connect

    Pullum, Laura L; Cui, Xiaohui; Vassev, Emil; Hinchey, Mike; Rouff, Christopher; Buskens, Richard

    2012-01-01

    Adaptive systems are critical for future space and other unmanned and intelligent systems. Verification of these systems is also critical for their use in systems with potential harm to human life or with large financial investments. Due to their nondeterministic nature and extremely large state space, current methods for verification of software systems are not adequate to provide a high level of assurance for them. The combination of stabilization science, high performance computing simulations, compositional verification and traditional verification techniques, plus operational monitors, provides a complete approach to verification and deployment of adaptive systems that has not been used before. This paper gives an overview of this approach.

  17. Precision Pointing System Development

    SciTech Connect

    BUGOS, ROBERT M.

    2003-03-01

    The development of precision pointing systems has been underway in Sandia's Electronic Systems Center for over thirty years. Important areas of emphasis are synthetic aperture radars and optical reconnaissance systems. Most applications are in the aerospace arena, with host vehicles including rockets, satellites, and manned and unmanned aircraft. Systems have been used on defense-related missions throughout the world. Presently in development are pointing systems with accuracy goals in the nanoradian regime. Future activity will include efforts to dramatically reduce system size and weight through measures such as the incorporation of advanced materials and MEMS inertial sensors.

  18. Weather Information System

    NASA Technical Reports Server (NTRS)

    1995-01-01

    WxLink is an aviation weather system based on advanced airborne sensors, precise positioning available from the satellite-based Global Positioning System, cockpit graphics and a low-cost datalink. It is a two-way system that uplinks weather information to the aircraft and downlinks automatic pilot reports of weather conditions aloft. Manufactured by ARNAV Systems, Inc., the original technology came from Langley Research Center's cockpit weather information system, CWIN (Cockpit Weather INformation). The system creates radar maps of storms, lightning and reports of surface observations, offering improved safety, better weather monitoring and substantial fuel savings.

  19. Airborne oceanographic lidar system

    NASA Technical Reports Server (NTRS)

    1975-01-01

    Specifications and preliminary design of an Airborne Oceanographic Lidar (AOL) system, which is to be constructed for installation and used on a NASA Wallops Flight Center (WFC) C-54 research aircraft, are reported. The AOL system is to provide an airborne facility for use by various government agencies to demonstrate the utility and practicality of hardware of this type in the wide area collection of oceanographic data on an operational basis. System measurement and performance requirements are presented, followed by a description of the conceptual system approach and the considerations attendant to its development. System performance calculations are addressed, and the system specifications and preliminary design are presented and discussed.

  20. Power system interface and umbilical system study

    NASA Technical Reports Server (NTRS)

    1980-01-01

    System requirements and basic design criteria were defined for berthing or docking a payload to the 25 kW power module which will provide electrical power and attitude control, cooling, data transfer, and communication services to free-flying and Orbiter sortie payloads. The selected umbilical system concept consists of four assemblies and command and display equipment to be installed at the Orbiter payload specialist station: (1) a movable platen assembly which is attached to the power system with EVA operable devices; (2) a slave platen assembly which is attached to the payload with EVA operable devices; (3) a fixed secondary platen permanently installed in the power system; and (4) a fixed secondary platen permanently installed on the payload. Operating modes and sequences are described.

  1. Business System Planning Project System Requirements Specification

    SciTech Connect

    NELSON, R.E.

    2000-09-08

    The purpose of the Business Systems Planning Project System Requirements Specification (SRS) is to provide the outline and contents of the requirements for the CH2M HILL Hanford Group, Inc. (CHG) integrated business and technical information systems. The SRS will translate proposed objectives into the statement of the functions that are to be performed and data and information flows that they require. The requirements gathering methodology will use (1) facilitated group requirement sessions; (2) individual interviews; (3) surveys; and (4) document reviews. The requirements will be verified and validated through coordination of the technical requirement team and CHG Managers. The SRS document used the content and format specified in Lockheed Martin Services, Inc. Organization Standard Software Practices in conjunction with the Institute of Electrical and Electronics Engineers Standard 8340-1984 for Systems Requirements Documents.

  2. NASA's SPICE System Models the Solar System

    NASA Technical Reports Server (NTRS)

    Acton, Charles

    1996-01-01

    SPICE is NASA's multimission, multidiscipline information system for assembling, distributing, archiving, and accessing space science geometry and related data used by scientists and engineers for mission design and mission evaluation, detailed observation planning, mission operations, and science data analysis.

  3. Small engine technology programs

    NASA Technical Reports Server (NTRS)

    Niedzwiecki, Richard W.

    1990-01-01

    Described here is the small engine technology program being sponsored at the Lewis Research Center. Small gas turbine research is aimed at general aviation, commuter aircraft, rotorcraft, and cruise missile applications. The Rotary Engine program is aimed at supplying fuel flexible, fuel efficient technology to the general aviation industry, but also has applications to other missions. The Automotive Gas Turbine (AGT) and Heavy-Duty Diesel Transport Technology (HDTT) programs are sponsored by DOE. The Compound Cycle Engine program is sponsored by the Army. All of the programs are aimed towards highly efficient engine cycles, very efficient components, and the use of high temperature structural ceramics. This research tends to be generic in nature and has broad applications. The HDTT, rotary technology, and the compound cycle programs are all examining approaches to minimum heat rejection, or 'adiabatic' systems employing advanced materials. The AGT program is also directed towards ceramics application to gas turbine hot section components. Turbomachinery advances in the gas turbine programs will benefit advanced turbochargers and turbocompounders for the intermittent combustion systems, and the fundamental understandings and analytical codes developed in the research and technology programs will be directly applicable to the system projects.

  4. User Registration Systems for Distributed Systems

    NASA Astrophysics Data System (ADS)

    Murphy, K. J.; Cechini, M.; Pilone, D.; Mitchell, A.

    2010-12-01

    As NASA’s Earth Observing System Data and Information System (EOSDIS) systems have evolved over the years, most of the EOSDIS data are now available to users via anonymous on-line access. Although the changes have improved the dissemination efficiency of earth science data, the anonymous access has made it difficult to characterize users, capture metrics on the value of EOSDIS and provide customized services that benefit users. As the number of web-based applications continues to grow, data centers and application providers have implemented their own user registration systems and provided new tools and interfaces for their registered users. This has led to the creation of independent registration systems for accessing data and interacting with online tools and services. The user profile information maintained at each of these registration systems is not consistent and the registration enforcement varies by system as well. This problem is in no way unique to EOSDIS and represents a general challenge to the distributed computing community. In a study done in 2007(http://www2007.org/papers/paper620.pd), the average user has approximately 7 passwords for about 25 accounts and enters a password 8 times a day. These numbers have only increased in the last three years. To try and address this, a number of solutions have been offered including Single Sign-On solutions using a common backend like Microsoft Active Directory or an LDAP server, trust based identity providers like OpenID, and various forms of authorization delegation like OAuth or SAML/XACML. This talk discusses the differences between authentication and authorization, the state of the more popular user registration solutions available for distributed use, and some of the technical and policy drivers that need to be considered when incorporating a user registration system into your application.

  5. Enabling Systems Biology Approaches Through Microfabricated Systems

    PubMed Central

    Zhan, Mei; Chingozha, Loice; Lu, Hang

    2014-01-01

    With the experimental tools and knowledge that have accrued from a long history of reductionist biology, we can now start to put the pieces together and begin to understand how biological systems function as an integrated whole. Here, we describe how microfabricated tools have demonstrated promise in addressing experimental challenges in throughput, resolution and sensitivity to support systems-based approaches to biological understanding. PMID:23984862

  6. System and method for creating expert systems

    NASA Technical Reports Server (NTRS)

    Hughes, Peter M. (Inventor); Luczak, Edward C. (Inventor)

    1998-01-01

    A system and method provides for the creation of a highly graphical expert system without the need for programming in code. An expert system is created by initially building a data interface, defining appropriate Mission, User-Defined, Inferred, and externally-generated GenSAA (EGG) data variables whose data values will be updated and input into the expert system. Next, rules of the expert system are created by building appropriate conditions of the rules which must be satisfied and then by building appropriate actions of rules which are to be executed upon corresponding conditions being satisfied. Finally, an appropriate user interface is built which can be highly graphical in nature and which can include appropriate message display and/or modification of display characteristics of a graphical display object, to visually alert a user of the expert system of varying data values, upon conditions of a created rule being satisfied. The data interface building, rule building, and user interface building are done in an efficient manner and can be created without the need for programming in code.

  7. Integrated Systems Health Management for Intelligent Systems

    NASA Technical Reports Server (NTRS)

    Figueroa, Fernando; Melcher, Kevin

    2011-01-01

    The implementation of an integrated system health management (ISHM) capability is fundamentally linked to the management of data, information, and knowledge (DIaK) with the purposeful objective of determining the health of a system. Management implies storage, distribution, sharing, maintenance, processing, reasoning, and presentation. ISHM is akin to having a team of experts who are all individually and collectively observing and analyzing a complex system, and communicating effectively with each other in order to arrive at an accurate and reliable assessment of its health. In this chapter, concepts, procedures, and approaches are presented as a foundation for implementing an ISHM capability relevant to intelligent systems. The capability stresses integration of DIaK from all elements of a system, emphasizing an advance toward an on-board, autonomous capability. Both ground-based and on-board ISHM capabilities are addressed. The information presented is the result of many years of research, development, and maturation of technologies, and of prototype implementations in operational systems.

  8. Immune System (For Parents)

    MedlinePlus

    ... lock onto them. T cells are like the soldiers, destroying the invaders that the intelligence system has ... can't be prevented, you can help your child's immune system stay stronger and fight illnesses by ...

  9. System status display evaluation

    NASA Technical Reports Server (NTRS)

    Summers, Leland G.

    1988-01-01

    The System Status Display is an electronic display system which provides the crew with an enhanced capability for monitoring and managing the aircraft systems. A flight simulation in a fixed base cockpit simulator was used to evaluate alternative design concepts for this display system. The alternative concepts included pictorial versus alphanumeric text formats, multifunction versus dedicated controls, and integration of the procedures with the system status information versus paper checklists. Twelve pilots manually flew approach patterns with the different concepts. System malfunctions occurred which required the pilots to respond to the alert by reconfiguring the system. The pictorial display, the multifunction control interfaces collocated with the system display, and the procedures integrated with the status information all had shorter event processing times and lower subjective workloads.

  10. Central nervous system

    MedlinePlus

    The central nervous system is composed of the brain and spinal cord. Your brain and spinal cord serve as the main "processing center" for your entire nervous system. They control all the workings of your body.

  11. Leasing Residential PV Systems

    SciTech Connect

    Rutberg, Michael; Bouza, Antonio

    2013-11-01

    The article discusses the adoption, consequences and current market status of the leasing of residential photovoltaic systems. It addresses attributed energy savings and market potential of residential system leasing.

  12. School System Empires

    ERIC Educational Resources Information Center

    Huberman, Michael

    1972-01-01

    Although most educational systems are resistant to change, there are some features of the community, of the teachers, of government, and of the system that enable one to predict the likelihood of an innovation being accepted and implemented. (AL)

  13. Henry Ford Health Systems

    Cancer.gov

    Henry Ford Health Systems evolved from a hospital into a system delivering care to 2.5 million patients and includes the Cancer Epidemiology, Prevention and Control Program, which focuses on epidemiologic and public health aspects of cancer.

  14. Highly Autonomous Systems Workshop

    NASA Technical Reports Server (NTRS)

    Doyle, R.; Rasmussen, R.; Man, G.; Patel, K.

    1998-01-01

    It is our aim by launching a series of workshops on the topic of highly autonomous systems to reach out to the larger community interested in technology development for remotely deployed systems, particularly those for exploration.

  15. Double Degenerate Binary Systems

    SciTech Connect

    Yakut, K.

    2011-09-21

    In this study, angular momentum loss via gravitational radiation in double degenerate binary (DDB)systems (NS + NS, NS + WD, WD + WD, and AM CVn) is studied. Energy loss by gravitational waves has been estimated for each type of systems.

  16. Torque control system

    NASA Technical Reports Server (NTRS)

    Studenick, D. K.; Tyler, A. L.; Squillari, W.

    1975-01-01

    System stabilizes aximuth of gondolas which are carried by high-altitude balloons as platforms for tracking telescopes. When telescopes must be constantly aimed at specific targets, control system stabilizes gondola to within 5 arc-seconds.

  17. Immune System and Disorders

    MedlinePlus

    Your immune system is a complex network of cells, tissues, and organs that work together to defend against germs. It ... t, to find and destroy them. If your immune system cannot do its job, the results can be ...

  18. Pneumonia - weakened immune system

    MedlinePlus

    ... medlineplus.gov/ency/article/000093.htm Pneumonia - weakened immune system To use the sharing features on this page, ... fighting off infection because of problems with the immune system. This type of disease is called "pneumonia in ...

  19. Male Reproductive System

    MedlinePlus

    ... gamete, the egg or ovum , meet in the female's reproductive system to create a new individual. Both the male and female reproductive systems are essential for reproduction. Humans, like other organisms, ...

  20. Male Reproductive System

    MedlinePlus

    ... gamete, the egg or ovum, meet in the female's reproductive system to create a baby. Both the male and female reproductive systems are essential for reproduction. Humans pass certain characteristics ...

  1. Power system stability

    SciTech Connect

    Not Available

    1984-03-01

    The following papers are included: exact Lagrangians for linear nonconservative systems; linear nonconservative systems with asymmetric parameters derivable from a Lagrangian; some remarks on the derivability of linear nonconservative systems from a Lagrangian; dynamic response by means of functions of matrices; a direct construction of first integrals for certain nonlinear dynamical systems; derivation of the Brayton-Moser equations from a topological mixed potential function; quadratic integrals for linear nonconservative systems and their connection with the inverse problem of Lagrangian dynamics; generalized Lagrangian and conservation law for the damped harmonic oscillator; connections between the generalized Hamilton-Lagrange and Brayton-Moser equations; time-dependent linear systems derivable from a variational principle; the generalized Lagrange formulation for nonlinear RLC networks; the Helmholtz conditions revisited - a new approach to the inverse problem of Lagrangian dynamics; time-dependent linear systems derivable from a variational principle II; and conservation laws for some separable gyroscopic dynamical systems.

  2. Silver recovery system data

    SciTech Connect

    Boulineau, B.

    1991-08-26

    In August of 1990 the Savannah River Site Photography Group began testing on a different type of silver recovery system. This paper describes the baseline study and the different phases of installation and testing of the system.

  3. Absorption heat pump system

    DOEpatents

    Grossman, Gershon

    1984-01-01

    The efficiency of an absorption heat pump system is improved by conducting liquid from a second stage evaporator thereof to an auxiliary heat exchanger positioned downstream of a primary heat exchanger in the desorber of the system.

  4. JT-60 Control System

    SciTech Connect

    Yonekawa, I.; Kawamata, Y.; Totsuka, T.; Akasaka, H.; Sueoka, M.; Kurihara, K.; Kimura, T.

    2002-09-15

    The present status of the JT-60U control system is reported including its original design concept, the progress of the system, and various modifications since the JT-60 upgrade. This control system has features of a functionally distributed and hierarchical structure, using CAMAC interfaces initially, which have been replaced by versatile module Europe (VME)-bus interfaces, and a protective interlock system composed of both software and hard-wired interlock logics. Plant monitoring and control are performed by efficient data communication through CAMAC highways and Ethernet with TCP/IP protocols. Sequential control of plasma discharges is executed by a combination of a remodeled VME-bus system and a timing system. A real-time plasma control system and a human interface system have been continuously modified corresponding to the progress of JT-60U experiments.

  5. Human Resource Accounting System

    ERIC Educational Resources Information Center

    Cerullo, Michael J.

    1974-01-01

    Main objectives of human resource accounting systems are to satisfy the informational demands made by investors and by operating managers. The paper's main concern is with the internal uses of a human asset system. (Author)

  6. Secondary power systems

    SciTech Connect

    Not Available

    1985-01-01

    In aeronautical engineering secondary power systems have long played second fiddle to the airframe, the engine, and indeed, the avionics. This collection of papers is thus timely, and its publication by the Institution of Mechanical Engineers appropriate, as secondary power systems in modern aircraft present challenging mechanical engineering problems. In military aircraft demands for electrical and hydraulic power and high pressure air have grown over the past two decades. To these basic needs are added requirements for emergency power, ground power, and independent engine starting. Additionally increased reliability and maintainability is demanded from all secondary power systems. Complete contents: What is a secondary power system. Modern technology secondary power systems for next generation military aircraft; Integrated power units; Secondary power system gearbox; Starting the system - air turbine starters; Auxiliary and emergency power system; Secondary hydraulic power generation; Advanced technology electrical power generation equipment.

  7. Alarm Notification System

    1995-03-12

    AN/EMS, the Alarm Notification Energy Management System, is used to monitor digital sensors in PETC buildings and to notify the safety/security operator by both a video and an audio system when a possibly hazardous condition arises.

  8. Biomedical recording system

    NASA Technical Reports Server (NTRS)

    Vick, H. A.

    1970-01-01

    System collects medical data directly from patients and permanently records and displays several parameters - electrocardiograph, electroencephalograph, heart rate, respiration rate, auscultatory blood pressure, leg circumference changes, body temperature, and time. Components and operation of the system are described.

  9. Male Reproductive System

    MedlinePlus

    ... Surveillance Modules » Anatomy & Physiology » Reproductive System » Male Reproductive System Cancer Registration & Surveillance Modules Anatomy & Physiology Intro to the Human Body Body Functions & Life Process Anatomical Terminology Review Quiz ...

  10. Modular optical detector system

    DOEpatents

    Horn, Brent A.; Renzi, Ronald F.

    2006-02-14

    A modular optical detector system. The detector system is designed to detect the presence of molecules or molecular species by inducing fluorescence with exciting radiation and detecting the emitted fluorescence. Because the system is capable of accurately detecting and measuring picomolar concentrations it is ideally suited for use with microchemical analysis systems generally and capillary chromatographic systems in particular. By employing a modular design, the detector system provides both the ability to replace various elements of the detector system without requiring extensive realignment or recalibration of the components as well as minimal user interaction with the system. In addition, the modular concept provides for the use and addition of a wide variety of components, including optical elements (lenses and filters), light sources, and detection means, to fit particular needs.

  11. Gleason grading system

    MedlinePlus

    ... medlineplus.gov/ency/patientinstructions/000920.htm Gleason grading system To use the sharing features on this page, ... score of between 5 and 7. Gleason Grading System Sometimes, it can be hard to predict how ...

  12. Multiple system atrophy

    MedlinePlus

    ... page: //medlineplus.gov/ency/article/000757.htm Multiple system atrophy To use the sharing features on this page, please enable JavaScript. Multiple system atrophy (MSA) is a rare condition that causes ...

  13. Semiotic labelled deductive systems

    SciTech Connect

    Nossum, R.T.

    1996-12-31

    We review the class of Semiotic Models put forward by Pospelov, as well as the Labelled Deductive Systems developed by Gabbay, and construct an embedding of Semiotic Models into Labelled Deductive Systems.

  14. Immune System and Disorders

    MedlinePlus

    ... substances that are usually not harmful Immune deficiency diseases - disorders in which the immune system is missing one or more of its parts Autoimmune diseases - diseases causing your immune system to attack your ...

  15. Avian respiratory system disorders

    USGS Publications Warehouse

    Olsen, G.H.

    1989-01-01

    Diagnosing and treating respiratory diseases in avian species requires a basic knowledge about the anatomy and physiology of this system in birds. Differences between mammalian and avian respiratory system function, diagnosis, and treatment are highlighted.

  16. Absorption heat pump system

    DOEpatents

    Grossman, G.

    1982-06-16

    The efficiency of an absorption heat pump system is improved by conducting liquid from a second stage evaporator thereof to an auxiliary heat exchanger positioned downstream of a primary heat exchanger in the desorber of the system.

  17. Information retrieval system

    NASA Technical Reports Server (NTRS)

    Berg, R. F.; Holcomb, J. E.; Kelroy, E. A.; Levine, D. A.; Mee, C., III

    1970-01-01

    Generalized information storage and retrieval system capable of generating and maintaining a file, gathering statistics, sorting output, and generating final reports for output is reviewed. File generation and file maintenance programs written for the system are general purpose routines.

  18. Intensive care alarm system

    NASA Technical Reports Server (NTRS)

    Christensen, J. L.; Herbert, A. L.

    1973-01-01

    Inductive loop has been added to commercially available call system fitted with earphone receiver. System transmits high frequency signals to nurse's receiver to announce patient's need for help without disturbing others.

  19. INL Autonomous Navigation System

    2005-03-30

    The INL Autonomous Navigation System provides instructions for autonomously navigating a robot. The system permits high-speed autonomous navigation including obstacle avoidance, waypoing navigation and path planning in both indoor and outdoor environments.

  20. Portable Dental System

    NASA Technical Reports Server (NTRS)

    1980-01-01

    Portable dental system provides dental care in isolated communities. System includes a patient's chair and a dentist's stool, an X-ray machine and a power unit, all of which fold into compact packages. A large yellow "pumpkin" is a collapsible compressed air tank. Portable system has been used successfully in South America in out of the way communities with this back-packable system, and in American nursing homes. This product is no longer manufactured.

  1. Space shuttle revitalization system

    NASA Technical Reports Server (NTRS)

    Quattrone, P. D.

    1985-01-01

    The Space Shuttle air revitalization system is discussed. The sequential steps in loop closure are examined and a schematic outline of the regenerative air revitalization system is presented. Carbon dioxide reduction subsystem concepts are compared. Schemes are drawn for: static feedwater electrolysis cell, solid polymer electrolyte water electrolysis cell, air revitalization system, nitrogen generation reactions, nitrogen subsystem staging, vapor compression distillation subsystem, thermoelectric integrated membrane evaporation subsystem, catalytic distillation water reclamation subsystem, and space shuttle solid waste management system.

  2. Modular integrated video system

    SciTech Connect

    Gaertner, K.J.; Heaysman, B.; Holt, R.; Sonnier, C.

    1986-01-01

    The Modular Integrated Video System (MIVS) is intended to provide a simple, highly reliable closed circuit television (CCTV) system capable of replacing the IAEA Twin Minolta Film Camera Systems in those safeguards facilities where mains power is readily available, and situations where it is desired to have the CCTV camera separated from the CCTV recording console. This paper describes the MIVS and the Program Plan which is presently being followed for the development, testing, and implementation of the system.

  3. Linear system theory

    NASA Technical Reports Server (NTRS)

    Callier, Frank M.; Desoer, Charles A.

    1991-01-01

    The aim of this book is to provide a systematic and rigorous access to the main topics of linear state-space system theory in both the continuous-time case and the discrete-time case; and the I/O description of linear systems. The main thrusts of the work are the analysis of system descriptions and derivations of their properties, LQ-optimal control, state feedback and state estimation, and MIMO unity-feedback systems.

  4. Intermediate water recovery system

    NASA Technical Reports Server (NTRS)

    Deckman, G.; Anderson, A. R. (Editor)

    1973-01-01

    A water recovery system for collecting, storing, and processing urine, wash water, and humidity condensates from a crew of three aboard a spacecraft is described. The results of a 30-day test performed on a breadboard system are presented. The intermediate water recovery system produced clear, sterile, water with a 96.4 percent recovery rate from the processed urine. Recommendations for improving the system are included.

  5. Visual Alert System

    NASA Technical Reports Server (NTRS)

    1985-01-01

    A visual alert system resulted from circuitry developed by Applied Cybernetics Systems for Langley as part of a space related telemetry system. James Campman, Applied Cybernetics president, left the company and founded Grace Industries, Inc. to manufacture security devices based on the Langley technology. His visual alert system combines visual and audible alerts for hearing impaired people. The company also manufactures an arson detection device called the electronic nose, and is currently researching additional applications of the NASA technology.

  6. Lithium battery management system

    DOEpatents

    Dougherty, Thomas J.

    2012-05-08

    Provided is a system for managing a lithium battery system having a plurality of cells. The battery system comprises a variable-resistance element electrically connected to a cell and located proximate a portion of the cell; and a device for determining, utilizing the variable-resistance element, whether the temperature of the cell has exceeded a predetermined threshold. A method of managing the temperature of a lithium battery system is also included.

  7. Space power systems technology

    NASA Technical Reports Server (NTRS)

    Coulman, George A.

    1994-01-01

    Reported here is a series of studies which examine several potential catalysts and electrodes for some fuel cell systems, some materials for space applications, and mathematical modeling and performance predictions for some solid oxide fuel cells and electrolyzers. The fuel cell systems have a potential for terrestrial applications in addition to solar energy conversion in space applications. Catalysts and electrodes for phosphoric acid fuel cell systems and for polymer electrolyte membrane (PEM) fuel cell and electrolyzer systems were examined.

  8. Automated RTOP Management System

    NASA Technical Reports Server (NTRS)

    Hayes, P.

    1984-01-01

    The structure of NASA's Office of Aeronautics and Space Technology electronic information system network from 1983 to 1985 is illustrated. The RTOP automated system takes advantage of existing hardware, software, and expertise, and provides: (1) computerized cover sheet and resources forms; (2) electronic signature and transmission; (3) a data-based information system; (4) graphics; (5) intercenter communications; (6) management information; and (7) text editing. The system is coordinated with Headquarters efforts in codes R,E, and T.

  9. Nonsurvivable momentum exchange system

    NASA Technical Reports Server (NTRS)

    Roder, Russell (Inventor); Ahronovich, Eliezer (Inventor); Davis, III, Milton C. (Inventor)

    2007-01-01

    A demiseable momentum exchange system includes a base and a flywheel rotatably supported on the base. The flywheel includes a web portion defining a plurality of web openings and a rim portion. The momentum exchange system further includes a motor for driving the flywheel and a cover for engaging the base to substantially enclose the flywheel. The system may also include components having a melting temperature below 1500 degrees Celsius. The momentum exchange system is configured to demise on reentry.

  10. Digital communication systems

    NASA Astrophysics Data System (ADS)

    Peebles, Peyton Z., Jr.

    The fundamental principles of digital communication and the design of practical digital communication systems are explored in an introductory textbook for senior and graduate students of electrical engineering. Chapters are devoted to sampling principles, baseband digital waveforms, baseband digital systems, bandpass binary digital systems, and M-ary digital systems. Deterministic signals, networks, and random-signal theory are reviewed in extensive appendices, and graphs, flow charts, diagrams, and problems are provided.

  11. Space station power system

    NASA Technical Reports Server (NTRS)

    Baraona, Cosmo R.

    1987-01-01

    The major requirements and guidelines that affect the space station configuration and power system are explained. The evolution of the space station power system from the NASA program development-feasibility phase through the current preliminary design phase is described. Several early station concepts are described and linked to the present concept. Trade study selections of photovoltaic system technologies are described in detail. A summary of present solar dynamic and power management and distribution systems is also given.

  12. Goddard Ground System Environment

    NASA Technical Reports Server (NTRS)

    Liu, Ben

    2009-01-01

    This slide presentation reviews the Goddard Mission Services Evolution Center's work in providing the Ground System Infrastructure to allow for standard interfaces, and allow for a mix of heritage and new components. This software has been used by NASA and other Government users. Telemetry and command services are also provided as are mission planning and scheduling systems. Other areas that the presentation covers are work on trending systems, and data management system.

  13. Video Scene Recognition System

    NASA Astrophysics Data System (ADS)

    Wong, Robert Y.; Sallak, Rashid M.

    1983-03-01

    Microprocessors are used to show a possible implementation of a multiprocessoi system for video scene recognition operations. The system was designed in the multiple input stream and multiple data stream (MIMD) configuration. "Autonomous cooperation" among the working processors is supervised by a global operating system, the heart of which is the scheduler. The design of the scheduler and the overall operations of the system are discussed.

  14. TMACS system description

    SciTech Connect

    Scaief, C.C.

    1995-10-17

    This document provides a description of the Tank Monitor and Control System (TMACS). It is intended as an introduction for those persons unfamiliar with the system as well as a reference document for the users, maintenance personnel, and system designers. In addition to describing the system, the document outlines the associated drawing documentation, provides maintenance and spare parts information, and discusses other TMACS documents that provide additional detail

  15. Norway's Regional College System.

    ERIC Educational Resources Information Center

    Hanisch, Thor Einar

    1981-01-01

    Examines the structure of Norway's short-cycle educational system. Describes how the district colleges function individually as units and collectively within a regional system to provide comprehensive, community-based educational opportunities. Discusses the incorporation of a variety of colleges into the regional system and encourages increased…

  16. Personal Food System Mapping

    ERIC Educational Resources Information Center

    Wilsey, David; Dover, Sally

    2014-01-01

    Personal food system mapping is a practical means to engage community participants and educators in individualized and shared learning about food systems, decisions, and behaviors. Moreover, it is a useful approach for introducing the food system concept, which is somewhat abstract. We developed the approach to capture diversity of personal food…

  17. Neutron radiographic viewing system

    NASA Technical Reports Server (NTRS)

    Leysath, W.; Brown, R. L.

    1972-01-01

    Neutron radiographic viewing system consisting of camera head and control processor is developed for use in nondestructive testing applications. Camera head consists of neutron-sensitive image intensifier system, power supply, and SEC vidicon camera head. Both systems, with their optics, are housed on test mount.

  18. Neutrino Factory Downstream Systems

    SciTech Connect

    Zisman, Michael S.

    2009-12-23

    We describe the Neutrino Factory accelerator systems downstream from the target and capture area. These include the bunching and phase rotation, cooling, acceleration, and decay ring systems. We also briefly discuss the R&D program under way to develop these systems, and indicate areas where help from CERN would be invaluable.

  19. Programmable Electronic Safety Systems

    SciTech Connect

    Parry, R.

    1993-05-01

    Traditionally safety systems intended for protecting personnel from electrical and radiation hazards at particle accelerator laboratories have made extensive use of electromechanical relays. These systems have the advantage of high reliability and allow the designer to easily implement failsafe circuits. Relay based systems are also typically simple to design, implement, and test. As systems, such as those presently under development at the Superconducting Super Collider Laboratory (SSCL), increase in size, and the number of monitored points escalates, relay based systems become cumbersome and inadequate. The move toward Programmable Electronic Safety Systems is becoming more widespread and accepted. In developing these systems there are numerous precautions the designer must be concerned with. Designing fail-safe electronic systems with predictable failure states is difficult at best. Redundancy and self-testing are prime examples of features that should be implemented to circumvent and/or detect failures. Programmable systems also require software which is yet another point of failure and a matter of great concern. Therefore the designer must be concerned with both hardware and software failures and build in the means to assure safe operation or shutdown during failures. This paper describes features that should be considered in developing safety systems and describes a system recently installed at the Accelerator Systems String Test (ASST) facility of the SSCL.

  20. Astromag data system concept

    NASA Technical Reports Server (NTRS)

    Roos, Darrell; Cheng, Chieh-San; Newsome, Penny; Nath, Nitya

    1989-01-01

    A feasible, top-level data system is defined that could accomplish and support the Astromag Data System functions and interfaces necessary to support the scientific objectives of Astromag. This data system must also be able to function in the environment of the Space Station Freedom Manned Base (SSFMB) and other anticipated NASA elements.

  1. Types of Data Systems

    ERIC Educational Resources Information Center

    Gould, Tate; Nicholas, Amy; Ruggiero, Tony; Blandford, William; Thayer, Sara; Bull, Bruce

    2015-01-01

    There are several types of data systems that support data from Part C/619 programs. Although the system types have similarities, each has its own unique characteristics and purposes. The attributes that make one type of data system a particularly good fit for one data-related need or function can be less desirable for another need or function. In…

  2. Immune System Quiz

    MedlinePlus

    ... Homework? Here's Help White House Lunch Recipes Quiz: Immune System KidsHealth > For Kids > Quiz: Immune System Print A A A Text Size How much do you know about your immune system? Find out by taking this quiz! View Survey ...

  3. Instructional System Development.

    ERIC Educational Resources Information Center

    Department of the Air Force, Washington, DC.

    The manual presents a technology of instructional design and a model for developing and conducting efficient and cost effective Air Force instructional systems. Chapter 1 provides an overview of Instructional System Development (ISD). Chapters 2-6 each focus on a step of the process: analysis of system requirements; definition of…

  4. System Documentation Manual.

    ERIC Educational Resources Information Center

    Semmel, Melvyn I.; Olson, Jerry

    The document is a system documentation manual of the Computer-Assisted Teacher Training System (CATTS) developed by the Center for Innovation in Teaching the Handicapped (Indiana University). CATTS is characterized as a system capable of providing continuous, instantaneous, and/or delayed feedback of relevant teacher-student interaction data to a…

  5. Special Education Resource System.

    ERIC Educational Resources Information Center

    Kampert, George J.

    The guide to the Special Education Resource System (SERS) of the Flour Bluff (Texas) school system contains policies and procedures regarding organization, services, and process of the system. Noted is the SERS purpose of providing information and access to appropriate instructional media and materials for special education personnel. Briefly…

  6. Systemic Change in Education.

    ERIC Educational Resources Information Center

    Reigeluth, Charles M., Ed.; Garfinkle, Robert J., Ed.

    This book provides new tools for thinking about and designing the education system. Four sections, each with its own introduction, follow Charles M. Reigeluth's introductory chapter, "Introduction: The Imperative for Systemic Change." Section 1 describes some theoretical frameworks for understanding the "big ideas" of system design. It includes:…

  7. Irrigation Systems Operation

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Effective operation of an irrigation system requires matching the operational characteristics of a system to the soil, crop, field, and water supply. Each of these components will affect the quality of the irrigation system performance. The performance measures used to characterize the irrigation sy...

  8. Nationale Roadmap Embedded Systems

    NASA Astrophysics Data System (ADS)

    Damm, Werner; Achatz, Reinhold; Beetz, Klaus; Broy, Manfred; Daembkes, Heinrich; Grimm, Klaus; Liggesmeyer, Peter

    Eingebettete Systeme" sind in ihrem Softwareanteil nicht sichtbar und doch hoch relevant für den Wirtschaftsstandort Deutschland. Ihre Bedeutung fasst die vorliegende Nationale Roadmap Embedded Systems in den folgenden 10 Thesen zusammen: These 1 Die zentralen ökonomischen und gesellschaftlichen Herausforderungen in Deutschland lassen sich ohne die Querschnittstechnologie Embedded Systems nicht lösen1.

  9. Firefighter's Breathing System

    NASA Technical Reports Server (NTRS)

    Mclaughlan, P. B.; Giorgini, E. A.; Sullivan, J. L.; Simmonds, M. R.; Beck, E. J.

    1976-01-01

    System, based on open-loop demand-type compressed air concept, is lighter and less bulky than former systems, yet still provides thirty minutes of air supply. Comfort, visibility, donning time, and breathing resistance have been improved. Apparatus is simple to recharge and maintain and is comparable in cost to previously available systems.

  10. Energy Systems Laboratory Groundbreaking

    SciTech Connect

    Hill, David; Otter, C.L.; Simpson, Mike; Rogers, J.W.

    2011-01-01

    INL recently broke ground for a research facility that will house research programs for bioenergy, advanced battery systems, and new hybrid energy systems that integrate renewable, fossil and nuclear energy sources. Here's video from the groundbreaking ceremony for INL's new Energy Systems Laboratory. You can learn more about CAES research at http://www.facebook.com/idahonationallaboratory.

  11. Arkansas Technology Information System.

    ERIC Educational Resources Information Center

    VanBiervliet, Alan; Parette, Howard P., Jr.

    The Arkansas Technology Information System (ARTIS) was developed to fill a significant void in existing systems of technical support to Arkansans with disabilities by creating and maintaining a consumer-responsive statewide system of data storage and retrieval regarding assistive technology and services. ARTIS goals also include establishment of a…

  12. Solar tracking system

    DOEpatents

    Okandan, Murat; Nielson, Gregory N.

    2016-07-12

    Solar tracking systems, as well as methods of using such solar tracking systems, are disclosed. More particularly, embodiments of the solar tracking systems include lateral supports horizontally positioned between uprights to support photovoltaic modules. The lateral supports may be raised and lowered along the uprights or translated to cause the photovoltaic modules to track the moving sun.

  13. Information extraction system

    DOEpatents

    Lemmond, Tracy D; Hanley, William G; Guensche, Joseph Wendell; Perry, Nathan C; Nitao, John J; Kidwell, Paul Brandon; Boakye, Kofi Agyeman; Glaser, Ron E; Prenger, Ryan James

    2014-05-13

    An information extraction system and methods of operating the system are provided. In particular, an information extraction system for performing meta-extraction of named entities of people, organizations, and locations as well as relationships and events from text documents are described herein.

  14. Unified Science - System.

    ERIC Educational Resources Information Center

    Thomson, Barbara S.

    The goals of this curriculum, developed as a summer course for the Young Scholars Program at The Ohio State University-Columbus, are as follows: (1) enable students to develop an understanding of the concept of a system; (2) help students gain an appreciation of the value of systems; (3) develop skills in working with systems; (4) expand skills in…

  15. System Orientation Manual.

    ERIC Educational Resources Information Center

    Scheppke, Jim, Ed.

    Intended as an orientation guide, this manual presents information on library network operations for use by staff and advisory council members of the Texas Library System. The first chapter describes the role of systems in public library development in Texas, with a delineation of the history of Texas library systems, a chronology of related…

  16. Polymerase chain reaction system

    DOEpatents

    Benett, William J.; Richards, James B.; Stratton, Paul L.; Hadley, Dean R.; Milanovich, Fred P.; Belgrader, Phil; Meyer, Peter L.

    2004-03-02

    A portable polymerase chain reaction DNA amplification and detection system includes one or more chamber modules. Each module supports a duplex assay of a biological sample. Each module has two parallel interrogation ports with a linear optical system. The system is capable of being handheld.

  17. No System? No Software!

    ERIC Educational Resources Information Center

    Conley, Donna

    1989-01-01

    Noting that the computer software cataloging system at the media center of the Washington (Illinois) Center for Continuing Education is essentially a card catalog in notebook form, this article describes aspects of the development and utilization of the system. Major sections describe: (1) software cataloging system terminology; (2) steps for…

  18. Power system restoration issues

    SciTech Connect

    Adibi, M.M. ); Kafka, R.J. )

    1991-04-01

    This article describes some of the problems encountered in the three phases of power system restoration (PSR). The three phases of PSR are: Planning for restart and reintegration of the bulk power supply; Actions during system degradation for saving and retaining critical sources of power; Restoration when the power system has stabilized at some degraded level.

  19. Jupiter System Observer

    NASA Technical Reports Server (NTRS)

    Senske, Dave; Prockter, Louise

    2008-01-01

    This slide presentation reviews the scientific philosophy that is guiding the planning behind the Jupiter System Observer (JSO). The JSO would be a long-term platform for studying Jupiter and the complete Jovian system. The goal is to advance the understanding of the fundamental processes of planetary systems, their formation and evolution.

  20. NPOx Decontamination System

    SciTech Connect

    Archibald, K.; Demmer, R.; Argyle, M.; Ancho, M.; Hai-Pao, J.

    2002-02-25

    The nitric acid/potassium permanganate/oxalic acid (NPOx) Phase II system is being prepared for remote operation at the Idaho National Engineering and Environmental Laboratory (INEEL). Several tests have been conducted to prepare the system for remote operation. This system performs very well with high decontamination efficiencies and very low quantities of waste generated during decontamination.

  1. Solar dynamic systems

    NASA Technical Reports Server (NTRS)

    Dustin, M. O.

    1985-01-01

    The development of the solar dynamic system is discussed. The benefits of the solar dynamic system over pv systems are enumerated. The history of the solar dynamic development is recounted. The purpose and approach of the advanced development are outlined. Critical concentrator technology and critical heat recover technology are examined.

  2. Desiccant humidity control system

    NASA Technical Reports Server (NTRS)

    Amazeen, J. (Editor)

    1973-01-01

    A regenerable sorbent system was investigated for controlling the humidity and carbon dioxide concentration of the space shuttle cabin atmosphere. The sorbents considered for water and carbon dioxide removal were silica gel and molecular sieves. Bed optimization and preliminary system design are discussed along with system optimization studies and weight penalites.

  3. Automotive energy management system

    SciTech Connect

    Shiber, S.

    1980-09-23

    A hydromechanical/hydrostatic automotive energy management system is described that is comprised of two hydraulic units, the system adapted to provide: an efficient, continuously variable optimal transmission ratio, an intermittent optimal engine operation in city traffic and regenerative braking, thereby, the system is able to reduce a car's fuel consumption by as much as one half while improving drivability.

  4. IDC System Specification Document.

    SciTech Connect

    Clifford, David J.

    2014-12-01

    This document contains the system specifications derived to satisfy the system requirements found in the IDC System Requirements Document for the IDC Reengineering Phase 2 project. Revisions Version Date Author/Team Revision Description Authorized by V1.0 12/2014 IDC Reengineering Project Team Initial delivery M. Harris

  5. Energy Systems Laboratory Groundbreaking

    ScienceCinema

    Hill, David; Otter, C.L.; Simpson, Mike; Rogers, J.W.;

    2013-05-28

    INL recently broke ground for a research facility that will house research programs for bioenergy, advanced battery systems, and new hybrid energy systems that integrate renewable, fossil and nuclear energy sources. Here's video from the groundbreaking ceremony for INL's new Energy Systems Laboratory. You can learn more about CAES research at http://www.facebook.com/idahonationallaboratory.

  6. FUNDAMENTALS OF TELEVISION SYSTEMS.

    ERIC Educational Resources Information Center

    KESSLER, WILLIAM J.

    DESIGNED FOR A READER WITHOUT SPECIAL TECHNICAL KNOWLEDGE, THIS ILLUSTRATED RESOURCE PAPER EXPLAINS THE COMPONENTS OF A TELEVISION SYSTEM AND RELATES THEM TO THE COMPLETE SYSTEM. SUBJECTS DISCUSSED ARE THE FOLLOWING--STUDIO ORGANIZATION AND COMPATIBLE COLOR TELEVISION PRINCIPLES, WIRED AND RADIO TRANSMISSION SYSTEMS, DIRECT VIEW AND PROJECTION…

  7. Microelectronics bioinstrumentation systems

    NASA Technical Reports Server (NTRS)

    Ko, W. H.

    1977-01-01

    Microelectronic bioinstrumentation systems to be employed in the Cardiovascular Deconditioning Program were developed. Implantable telemetry systems for long-term monitoring of animals on earth were designed to collect physiological data necessary for the understanding of the mechanisms of cardiovascular deconditioning. In-flight instrumentation systems, microelectronic instruments, and RF powering techniques for other life science experiments in the NASA program were studied.

  8. System integration report

    NASA Technical Reports Server (NTRS)

    Badler, N. I.; Korein, J. D.; Meyer, C.; Manoochehri, K.; Rovins, J.; Beale, J.; Barr, B.

    1985-01-01

    Several areas that arise from the system integration issue were examined. Intersystem analysis is discussed as it relates to software development, shared data bases and interfaces between TEMPUS and PLAID, shaded graphics rendering systems, object design (BUILD), the TEMPUS animation system, anthropometric lab integration, ongoing TEMPUS support and maintenance, and the impact of UNIX and local workstations on the OSDS environment.

  9. PERMIT COMPLIANCE SYSTEM (PCS)

    EPA Science Inventory

    The Permit Compliance System (PCS) is a computerized management information system which contains data on National Pollutant Discharge Elimination System (NPDES) permit-holding facilities. PCS keeps extensive records on more than 65,000 active water-discharge permits on sites loc...

  10. Economical space power systems

    NASA Technical Reports Server (NTRS)

    Burkholder, J. H.

    1980-01-01

    A commercial approach to design and fabrication of an economical space power system is investigated. Cost projections are based on a 2 kW space power system conceptual design taking into consideration the capability for serviceability, constraints of operation in space, and commercial production engineering approaches. A breakdown of the system design, documentation, fabrication, and reliability and quality assurance estimated costs are detailed.

  11. Small Modular Biomass Systems

    SciTech Connect

    2002-12-01

    This fact sheet provides information about modular biomass systems. Small modular biomass systems can help supply electricity to rural areas, businesses, and the billions of people who live without power worldwide. These systems use locally available biomass fuels such as wood, crop waste, animal manures, and landfill gas.

  12. The Texas Formula System.

    ERIC Educational Resources Information Center

    Steen, Ralph W.; And Others

    Explained and illustrated is the formula funding system used for colleges and universities in Texas. This system is considerably more complicated than the formulas used in other states. Data for institutions in the state system for fiscal 1978 are presented; actual appropriations are used rather than requests, and formula-produced amounts are…

  13. Medical Information Systems.

    ERIC Educational Resources Information Center

    Smith, Kent A.

    1986-01-01

    Description of information services from the National Library of Medicine (NLM) highlights a new system for retrieving information from NLM's databases (GRATEFUL MED); a formal Regional Medical Library Network; DOCLINE; the Unified Medical Language System; and Integrated Academic Information Management Systems. Research and development and the…

  14. Tara vacuum system

    SciTech Connect

    Post, R.S.; Brindza, P.; Goodrich, P.; Gaudreau, M.P.

    1985-11-01

    The Tara tandem mirror experiment vacuum system will be discussed including system design, specifications, and performance required for plug thermal barrier operation. A detailed description of the major pumpig systems, reflux control, plasma pumping, measurement and control, fast gas handling and quality control procedures will be presented. Data from the two 5 month periods of operation will be presented.

  15. Hydrothermal mineralising systems as critical systems

    NASA Astrophysics Data System (ADS)

    Hobbs, Bruce

    2015-04-01

    Hydrothermal mineralising systems as critical systems. Bruce E Hobbs1,2, Alison Ord1 and Mark A. Munro1. 1. Centre for Exploration Targeting, The University of Western Australia, M006, 35 Stirling Highway, Crawley, WA 6009, Australia. 2. CSIRO Earth and Resource Engineering, Bentley, WA, Australia Hydrothermal mineralising systems are presented as large, open chemical reactors held far from equilibrium during their life-time by the influx of heat, fluid and dissolved chemical species. As such they are nonlinear dynamical systems and need to be analysed using the tools that have been developed for such systems. Hydrothermal systems undergo a number of transitions during their evolution and this paper focuses on methods for characterising these transitions in a quantitative manner and establishing whether they resemble first or second (critical) phase transitions or whether they have some other kind of nature. Critical phase transitions are characterised by long range correlations for some parameter characteristic of the system, power-law probability distributions so that there is no characteristic length scale and a high sensitivity to perturbations; as one approaches criticality, characteristic parameters for the system scale in a power law manner with distance from the critical point. The transitions undergone in mineralised hydrothermal systems are: (i) widespread, non-localised mineral alteration involving exothermic mineral reactions that produce hydrous silicate phases, carbonates and iron-oxides, (ii) strongly localised veining, brecciation and/or stock-work formation, (iii) a series of endothermic mineral reactions involving the formation of non-hydrous silicates, sulphides and metals such as gold, (iv) multiple repetitions of transitions (ii) and (iii). We have quantified aspects of these transitions in gold deposits from the Yilgarn craton of Western Australia using wavelet transforms. This technique is convenient and fast. It enables one to establish if

  16. [System approach and system analysis in dietology].

    PubMed

    Samsonov, M A

    2004-01-01

    There is analysis of using of two variants of the auto-program of dietotherapy in the article: numeric system and basis system. They belong the same kind of building type, but are different in the type of functioning principle. Numeric system is built upon nosological principle taking into consideration the clinicopathogenetic features of disease. The basic diets built upon metabolic principle that a matter is adaptation of chemical content, alimentary and food value of diet for concrete mechanism of metabolic disturbance. At the same time metabolic conveyor is considered as system organization of the separate functional systems that are in the permanent dynamic and the interacting with each other. This organization is combined on the principle of auto regulation and set in correction and recovery of disturbed homeostasis as a whole. Selection of practical using of mentioned principles of diets is a right of the specialist-dieitian. Auto-program of diet building should help him in that and simplify the organization of dietotherapy. PMID:15049149

  17. Business System Planning Project, Preliminary System Design

    SciTech Connect

    EVOSEVICH, S.

    2000-10-30

    CH2M HILL Hanford Group, Inc. (CHG) is currently performing many core business functions including, but not limited to, work control, planning, scheduling, cost estimating, procurement, training, and human resources. Other core business functions are managed by or dependent on Project Hanford Management Contractors including, but not limited to, payroll, benefits and pension administration, inventory control, accounts payable, and records management. In addition, CHG has business relationships with its parent company CH2M HILL, U.S. Department of Energy, Office of River Protection and other River Protection Project contractors, government agencies, and vendors. The Business Systems Planning (BSP) Project, under the sponsorship of the CH2M HILL Hanford Group, Inc. Chief Information Officer (CIO), have recommended information system solutions that will support CHG business areas. The Preliminary System Design was developed using the recommendations from the Alternatives Analysis, RPP-6499, Rev 0 and will become the design base for any follow-on implementation projects. The Preliminary System Design will present a high-level system design, providing a high-level overview of the Commercial-Off-The-Shelf (COTS) modules and identify internal and external relationships. This document will not define data structures, user interface components (screens, reports, menus, etc.), business rules or processes. These in-depth activities will be accomplished at implementation planning time.

  18. Variants and Haplotypes in Angiotensinogen Gene Are Associated With Plasmatic Angiotensinogen Level in Mexican Population

    PubMed Central

    Balam-Ortiz, Eros; Esquivel-Villarreal, Adolfo; Alfaro-Ruiz, Luis; Carrillo, Karol; Elizalde, Adela; Gil, Trinidad; Urushihara, Maki; Kobori, Hiroyuki; Jimenez-Sanchez, Gerardo

    2011-01-01

    Introduction The plasmatic angiotensinogen (AGT) level has been associated with essential hypertension. Linkage analysis has found a relationship between the AGT gene locus and hypertension in the Mexican-American population, but studies have failed to identify genetic variants associated with hypertension or plasma AGT levels. This study analyzes the relationship between polymorphisms in the AGT gene and plasmatic AGT levels in Mexican population. Methods Nine polymorphisms in AGT gene were genotyped, and plasma AGT level was determined by enzyme-linked immunosorbent assay. Results Differences in AGT plasma levels were associated with 2 polymorphisms: T-20G, TT = 25.3 ± 8.3 versus TG + GG = 21.6 ± 8.8 μg/mL; P = 0.008 and C3389T (T174M), CC = 25.8 ± 9.9 versus TC + TT = 20.5 ± 5.4 μg/mL; P = 0.0002. Haplotype 2 was associated with low plasma AGT (−5.1 μg/mL [95% confidence interval: −8.6 to −1.6], P = 0.004) and Haplotype 8 was associated with high plasma AGT (6.5 μg/mL [95% confidence interval: 2.5 to 10.6], P = 0.001). This association remained after adjustment for covariates. A Likelihood Ratio Test for haplotype-phenotype association adjusted for covariates resulted in χ2 = 38.9, P = 0.0005. The total effect of the haplotypes on plasma AGT level variance was 19.5%. No association was identified between haplotypes and quantitative traits of blood pressure. Conclusions Two polymorphisms (T-20G and C3389T) and 2 haplotypes (H2 and H8) showed an association with plasma AGT levels in Mexican population. PMID:21629041

  19. CNEOST Control Software System

    NASA Astrophysics Data System (ADS)

    Wang, X.; Zhao, H. B.; Xia, Y.; Lu, H.; Li, B.

    2015-03-01

    In 2013, CNEOST (China Near Earth Object Survey Telescope) adapted its hardware system for the new CCD camera. Based on the new system architecture, the control software is re-designed and implemented. The software system adopts the message passing mechanism via WebSocket protocol, and improves its flexibility, expansibility, and scalability. The user interface with responsive web design realizes the remote operating under both desktop and mobile devices. The stable operating of software system has greatly enhanced the operation efficiency while reducing the complexity, and has also made a successful attempt for the future system design of telescope and telescope cloud.

  20. CNEOST Control Software System

    NASA Astrophysics Data System (ADS)

    Wang, Xin; Zhao, Hai-bin; Xia, Yan; Lu, Hao; Li, Bin

    2016-01-01

    In 2013, CNEOST (China Near Earth Object Survey Telescope) adapted its hardware system for the new CCD camera. Based on the new system architecture, the control software is re-designed and implemented. The software system adopts the messaging mechanism based on the WebSocket protocol, and possesses good flexibility and expansibility. The user interface based on the responsive web design has realized the remote observations under both desktop and mobile devices. The stable operation of the software system has greatly enhanced the operation efficiency while reducing the complexity, and has also made a successful attempt for the future system design of telescope and telescope cloud.