Science.gov

Sample records for air electrode structure

  1. Bifunctional oxygen/air electrodes

    NASA Astrophysics Data System (ADS)

    Jörissen, Ludwig

    A selective review on the materials and construction principles used for bifunctional oxygen/air electrodes is given. The discussion emphasizes the catalytically active materials used for the construction of these electrodes, which are a key component in electrically rechargeable air breathing electrochemical systems. Whereas, in acid electrolytes normally noble metal catalysts must be used, there is a possibility to use less expensive transition metal oxides in alkaline electrolytes. Typical transition metal oxides have the perovskite, pyrochlore and spinel structure.

  2. The Role of Air-Electrode Structure on the Incorporation of Immiscible PFCs in Nonaqueous Li-O2 Battery.

    PubMed

    Balaish, Moran; Ein-Eli, Yair

    2017-03-22

    Perfluorocarbons (PFCs) are considered advantageous additives to nonaqueous Li-O2 battery due to their superior oxygen solubility and diffusivity compared to common battery electrolytes. Up to now, the main focus was concentrated on PFCs-electrolyte investigation; however, no special attention was granted to the role of carbon structure in the PFCs-Li-O2 system. In our current research, immiscible PFCs, rather than miscible fluorinated ethers, were added to activated carbon class air electrode due to their higher susceptibility toward O2(•-) attack and to their ability to shift the reaction from two-phase to an artificial three-phase reaction zone. The results showed superior battery performance upon PFCs addition at lower current density (0.05 mA cm(-2)) but unexpectedly failed to do so at higher current density (0.1 and 0.2 mA cm(-2)), where oxygen transport limitation is best illustrated. The last was a direct result of liquid-liquid displacement phenomenon occurring when the two immiscible liquids were introduced into the porous carbon medium. The investigation and role of carbon structure on the mechanism upon PFCs addition to Li-O2 system are suggested based on electrochemical characterization, wettability behavior studies, and the physical adsorption technique. Finally, we suggest an optimum air-electrode structure enabling the incorporation of immiscible PFCs in a nonaqueous Li-O2 battery.

  3. Method of making an air electrode material having controlled sinterability

    DOEpatents

    Vasilow, Theodore R.; Kuo, Lewis J. H.; Ruka, Roswell J.

    1994-01-01

    A tubular, porous ceramic electrode structure (3) is made from the sintered admixture of doped lanthanum manganite and an additive containing cerium where a solid electrolyte (4), substantially surrounds the air electrode, and a porous outer fuel electrode (7) substantially surrounds the electrolyte, to form a fuel cell (1).

  4. Method of making an air electrode material having controlled sinterability

    DOEpatents

    Vasilow, T.R.; Kuo, L.J.H.; Ruka, R.J.

    1994-08-30

    A tubular, porous ceramic electrode structure is made from the sintered admixture of doped lanthanum manganite and an additive containing cerium where a solid electrolyte, substantially surrounds the air electrode, and a porous outer fuel electrode substantially surrounds the electrolyte, to form a fuel cell. 2 figs.

  5. Experimental study of cylindrical air electrodes

    NASA Astrophysics Data System (ADS)

    Viitanen, M.; Lamminen, J.; Lampinen, M. J.

    1991-11-01

    The electrodes studied here are cylindrical and prepared to be placed inside the inner surface of a sintered brass tube, which is nickel-plated. Previously we have reported on the preparation of flat air electrodes and also on long run tests carried out with these electrodes. The electrode material was prepared by the so-called wet method to obtain a carbon dough which is easy to handle. The material preparation remains the same, but owing to the different geometrical shape, the preparation of the electrode itself is quite different. We have studied here the long-term performance of these new cylindrical air electrodes and at the same time measured the carbonate content of the electrolyte. We have also analyzed by comparative methods which property of the electrode lowers the performance after a fairly long period.

  6. Compartmented electrode structure

    DOEpatents

    Vissers, Donald R.; Shimotake, Hiroshi; Gay, Eddie C.; Martino, Fredric J.

    1977-06-14

    Electrodes for secondary electrochemical cells are provided with compartments for containing particles of the electrode reactant. The compartments are defined by partitions that are generally impenetrable to the particles of reactant and, in some instances, to the liquid electrolyte used in the cell. During cycling of the cell, reactant material initially loaded into a particular compartment is prevented from migrating and concentrating within the lower portion of the electrode or those portions of the electrode that exhibit reduced electrical resistance.

  7. Subcutaneous electrode structure

    NASA Technical Reports Server (NTRS)

    Lund, G. F. (Inventor)

    1980-01-01

    A subcutaneous electrode structure suitable for a chronic implant and for taking a low noise electrocardiogram of an active animal, comprises a thin inflexible, smooth disc of stainless steel having a diameter as of 5 to 30 mm, which is sutured in place to the animal being monitored. The disc electrode includes a radially directed slot extending in from the periphery of the disc for approximately 1/3 of the diameter. Electrical connection is made to the disc by means of a flexible lead wire that extends longitudinally of the slot and is woven through apertures in the disc and held at the terminal end by means of a spot welded tab. Within the slot, an electrically insulative sleeve, such as silicone rubber, is placed over the wire. The wire with the sleeve mounted thereon is captured in the plane of the disc and within the slot by means of crimping tabs extending laterally of the slot and over the insulative wire. The marginal lip of the slot area is apertured and an electrically insulative potting material such as silicone rubber, is potted in place overlaying the wire slot region and through the apertures.

  8. Composite electrode/electrolyte structure

    DOEpatents

    Visco, Steven J.; Jacobson, Craig P.; DeJonghe, Lutgard C.

    2004-01-27

    Provided is an electrode fabricated from highly electronically conductive materials such as metals, metal alloys, or electronically conductive ceramics. The electronic conductivity of the electrode substrate is maximized. Onto this electrode in the green state, a green ionic (e.g., electrolyte) film is deposited and the assembly is co-fired at a temperature suitable to fully densify the film while the substrate retains porosity. Subsequently, a catalytic material is added to the electrode structure by infiltration of a metal salt and subsequent low temperature firing. The invention allows for an electrode with high electronic conductivity and sufficient catalytic activity to achieve high power density in ionic (electrochemical) devices such as fuel cells and electrolytic gas separation systems.

  9. Air electrode composition for solid oxide fuel cell

    DOEpatents

    Kuo, L.; Ruka, R.J.; Singhal, S.C.

    1999-08-03

    An air electrode composition for a solid oxide fuel cell is disclosed. The air electrode material is based on lanthanum manganite having a perovskite-like crystal structure ABO{sub 3}. The A-site of the air electrode composition comprises a mixed lanthanide in combination with rare earth and alkaline earth dopants. The B-site of the composition comprises Mn in combination with dopants such as Mg, Al, Cr and Ni. The mixed lanthanide comprises La, Ce, Pr and, optionally, Nd. The rare earth A-site dopants preferably comprise La, Nd or a combination thereof, while the alkaline earth A-site dopant preferably comprises Ca. The use of a mixed lanthanide substantially reduces raw material costs in comparison with compositions made from high purity lanthanum starting materials. The amount of the A-site and B-site dopants is controlled in order to provide an air electrode composition having a coefficient of thermal expansion which closely matches that of the other components of the solid oxide fuel cell. 3 figs.

  10. Air electrode composition for solid oxide fuel cell

    DOEpatents

    Kuo, Lewis; Ruka, Roswell J.; Singhal, Subhash C.

    1999-01-01

    An air electrode composition for a solid oxide fuel cell is disclosed. The air electrode material is based on lanthanum manganite having a perovskite-like crystal structure ABO.sub.3. The A-site of the air electrode composition comprises a mixed lanthanide in combination with rare earth and alkaline earth dopants. The B-site of the composition comprises Mn in combination with dopants such as Mg, Al, Cr and Ni. The mixed lanthanide comprises La, Ce, Pr and, optionally, Nd. The rare earth A-site dopants preferably comprise La, Nd or a combination thereof, while the alkaline earth A-site dopant preferably comprises Ca. The use of a mixed lanthanide substantially reduces raw material costs in comparison with compositions made from high purity lanthanum starting materials. The amount of the A-site and B-site dopants is controlled in order to provide an air electrode composition having a coefficient of thermal expansion which closely matches that of the other components of the solid oxide fuel cell.

  11. An improved bifunctional oxygen (air) electrode for reversible alkaline fuel cell systems and for rechargeable metal-air batteries

    NASA Astrophysics Data System (ADS)

    Kordesch, K.; Steininger, K.-H.; Tomantschger, K.

    1988-10-01

    Electrodes with a nickel layer of dual pore structure on the electrolyte side and a PTFE-bonded carbon layer on the oxygen (air) side are discussed, with application to space energy storage. During the electrolyis stage, the oxygen fills the large pores of the porous Ni structure with gas. During the discharge cycle, the iron/air or zinc/air cell of the carbon layer operates as a regular oxygen electrode.

  12. Improved zinc electrode and rechargeable zinc-air battery

    SciTech Connect

    Ross, P.N. Jr.

    1988-06-21

    The invention comprises an improved rechargeable zinc-air cell/battery having recirculating alkaline electrolyte and a zinc electrode comprising a porous foam support material which carries the active zinc electrode material. 5 figs.

  13. Electrocatalysts for bifunctional oxygen/air electrodes

    NASA Astrophysics Data System (ADS)

    Nikolova, V.; Iliev, P.; Petrov, K.; Vitanov, T.; Zhecheva, E.; Stoyanova, R.; Valov, I.; Stoychev, D.

    Oxygen reduction and evolution have been studied with respect to the development of bifunctional air/oxygen electrode (BFE). Three groups of catalysts have been prepared: (i) Cu xCo 3- xO 4 by thermal decomposition of mixed nitrate and carbonate precursors; (ii) thin films of Co-Ni-Te-O and Co-Te-O were deposited by vacuum co-evaporation of Co, Ni and TeO 2 and (iii) Co xO v/ZrO 2 films were obtained by electrochemical deposition. The electrochemical behavior of the chemically synthesized catalysts was studied on classical bilayered gas diffusion electrodes (GDEs), where the catalyst is in form of powder. The GDE catalyzed with vacuum deposited catalysts was prepared by direct deposition of the catalyst on gas-supplying layer, thus creating a ready-to-use gas diffusion electrode. Catalysts prepared electrochemically were first deposited on Ni foam and than pressed onto the gas-supplying layer. Different catalysts deposited on classical and originally designed GDEs were compared by their electrochemical performances. Cu 0.3Co 2.7O 4 deposited on a classical bilayered GDE with loading of 50 mg cm -2 exhibits stable current-voltage characteristics after 200 charge-discharge cycles in a real metal hydride-air battery. The electrochemically and vacuum deposited Co xO v/ZrO 2, Co-Ni-Te-O and Co-Te-O films exhibit much higher mass activity compared to Cu 0.2Co 2.8O 4 for both oxygen reduction and evolution reactions. The difference is that the loading of electrochemically and vacuum deposited films is 0.06 mg cm -2 only, which is a substantial advantage from a practical viewpoint.

  14. Oxide modified air electrode surface for high temperature electrochemical cells

    DOEpatents

    Singh, Prabhakar; Ruka, Roswell J.

    1992-01-01

    An electrochemical cell is made having a porous cermet electrode (16) and a porous lanthanum manganite electrode (14), with solid oxide electrolyte (15) between them, where the lanthanum manganite surface next to the electrolyte contains a thin discontinuous layer of high surface area cerium oxide and/or praseodymium oxide, preferably as discrete particles (30) in contact with the air electrode and electrolyte.

  15. Structural and microstructural characterization and properties of new phases in the Nd-Sr-Co-(Fe/Mn)-O system as air-electrodes in SOFCs.

    PubMed

    Boulahya, K; Muñoz Gil, D; Hassan, M; García Martin, S; Amador, U

    2017-01-24

    New oxides of the (NdSr)n+1MO3n+1 (M = Co and Mn or Fe) series are reported. Compounds of composition NdSrCo0.75Fe0.25O4.10, NdSrCo0.75Mn0.25O4.08 and Nd0.5Sr1.5Co0.75Mn0.25O3.86 are the n = 1 members of the Ruddlesden-Popper homologous series (K2NiF4 structural type) as determined by X-ray diffraction and different transmission electron microscopy techniques. Their crystal structure consists of connected (Co-Fe/Mn)O6 octahedra blocks separated by (Nd/Sr)O rock-salt like layers along the c-axis. Interstitial oxygen atoms or anion vacancies are induced depending on composition. Oxides with interstitial oxygen show good performances as intermediate temperature solid oxide fuel cell (IT-SOFC) cathode. The area-specific resistance values of electrodes made of these oxides at 973 K in air are 0.18 Ω cm(2) for NdSrCo0.75Fe0.25O4.10 and NdSrCo0.75Mn0.25O4.08 (comparable to the one of the state-of-the-art materials proposed as cathodes in IT-SOFC), and 1.38 Ω cm(2) for Nd0.5Sr1.5Co0.75Mn0.25O3.86.

  16. Bi-functional air electrodes for metal-air batteries. Final report, September 15, 1993--December 14, 1994

    SciTech Connect

    Swette, L.L.; Manoukian, M.; LaConti, A.B.

    1995-12-01

    The program was directed to the need for development of bifunctional air electrodes for Zn-Air batteries for the consumer market. The Zn-Air system, widely used as a primary cell for hearing-aid batteries and as a remote-site power source in industrial applications, has the advantage of high energy density, since it consumes oxygen from the ambient air utilizing a thin, efficient fuel-cell-type gas-diffusion electrode, and is comparatively low in cost. The disadvantages of the current technology are a relatively low rate capability, and the lack of simple reversibility. {open_quotes}Secondary{close_quotes} Zn-Air cells require a third electrode for oxygen evolution or mechanical replacement of the Zinc anodes; thus the development of a bifunctional air electrode (i.e., an electrode that can alternately consume and evolve oxygen) would be a significant advance in Zn-Air cell technology. Evaluations of two carbon-free non-noble metal perovskite-type catalyst systems, La{sub 1-x}CA{sub x}CoO{sub 3} as bifunctional catalysts for potential application in Zn-air batteries were carried out. The technical objectives were to develop higher-surface-area materials and to fabricate reversible electrodes by modifying the hydrophobic/hydrophilic balance of the catalyst-binder structures.

  17. Semiconductor devices having a recessed electrode structure

    DOEpatents

    Palacios, Tomas Apostol; Lu, Bin; Matioli, Elison de Nazareth

    2015-05-26

    An electrode structure is described in which conductive regions are recessed into a semiconductor region. Trenches may be formed in a semiconductor region, such that conductive regions can be formed in the trenches. The electrode structure may be used in semiconductor devices such as field effect transistors or diodes. Nitride-based power semiconductor devices are described including such an electrode structure, which can reduce leakage current and otherwise improve performance.

  18. Zinc electrode and rechargeable zinc-air battery

    SciTech Connect

    Ross, P.N. Jr.

    1989-06-27

    This patent describes an improved zinc electrode for a rechargeable zinc-air battery comprising an outer frame and a porous foam electrode support within the frame which is treated prior to the deposition of zinc thereon to inhibit the formation of zinc dendrites on the external surface thereof. The outer frame is provided with passageways for circulating an alkaline electrolyte through the treated zinc-coated porous foam. A novel rechargeable zinc-air battery system is also disclosed.

  19. Zinc electrode and rechargeable zinc-air battery

    SciTech Connect

    Ross, Jr., Philip N.

    1989-01-01

    An improved zinc electrode is disclosed for a rechargeable zinc-air battery comprising an outer frame and a porous foam electrode support within the frame which is treated prior to the deposition of zinc thereon to inhibit the formation of zinc dendrites on the external surface thereof. The outer frame is provided with passageways for circulating an alkaline electrolyte through the treated zinc-coated porous foam. A novel rechargeable zinc-air battery system is also disclosed which utilizes the improved zinc electrode and further includes an alkaline electrolyte within said battery circulating through the passageways in the zinc electrode and an external electrolyte circulation means which has an electrolyte reservoir external to the battery case including filter means to filter solids out of the electrolyte as it circulates to the external reservoir and pump means for recirculating electrolyte from the external reservoir to the zinc electrode.

  20. Electrode structure and methods of making same

    DOEpatents

    Ruud, James Anthony; Browall, Kenneth Walter; Rehg, Timothy Joseph; Renou, Stephane; Striker, Todd-Michael

    2010-04-06

    A method of making an electrode structure is provided. The method includes disposing an electrocatalytic material on an electrode, applying heat to the electrocatalytic material to form a volatile oxide of the electrocatalytic material, and applying a voltage to the electrode to reduce the volatile oxide to provide a number of nano-sized electrocatalytic particles on or proximate to a triple phase boundary, where the number of nano-sized electrocatalytic particles is greater on or proximate to the triple phase boundary than in an area that is not on or proximate to the triple phase boundary, and where the triple phase boundary is disposed on the electrode.

  1. Variations in the structure and electrochemical characteristics of membrane electrode assemblies during the endurance testing of hydrogen-air fuel cells

    NASA Astrophysics Data System (ADS)

    Avakov, V. B.; Aliev, A. D.; Bogdanovskaya, V. A.; Ivanitskii, B. A.; Kazanskii, L. P.; Kapustin, A. V.; Korchagin, O. V.; Landgraf, I. K.; Tarasevich, M. P.; Chalykh, A. E.

    2015-05-01

    Variations in the characteristics of a membrane-electrode assembly (MEA) are studied during the endurance testing of a hydrogen-air fuel cell (FC) based on a Nafion 212 proton conducting membrane and platinum catalysts. It is shown that the voltage drop observed during MEA testing was mainly due to physicochemical transformations of the cathode catalyst, i.e., the oxidation of platinum and its subsequent recrystallization with nanoparticle coarsening. It is established that the rate of degradation increases along with temperature and loading, and with periodic FC depressurization. It is concluded that the enhancing effects of additional factors of degradation, e.g., platinum ion transport to the proton-conducting membrane and corrosion of the carbon carrier, were responsible for these processes.

  2. Gradient porous electrode architectures for rechargeable metal-air batteries

    DOEpatents

    Dudney, Nancy J.; Klett, James W.; Nanda, Jagjit; Narula, Chaitanya Kumar; Pannala, Sreekanth

    2016-03-22

    A cathode for a metal air battery includes a cathode structure having pores. The cathode structure has a metal side and an air side. The porosity decreases from the air side to the metal side. A metal air battery and a method of making a cathode for a metal air battery are also disclosed.

  3. Metal | polypyrrole battery with the air regenerated positive electrode

    NASA Astrophysics Data System (ADS)

    Grgur, Branimir N.

    2014-12-01

    Recharge characteristics of the battery based on the electrochemically synthesized polypyrrole cathode and aluminum, zinc, or magnesium anode in 2 M NH4Cl are investigated. It is shown that polypyrrole electrode can be regenerated by the reoxidation with the dissolved oxygen from the air. Using the polypyrrole synthesized on high surface graphite-felt electrode under modest discharge conditions, stable discharge voltage of 1.1 V is obtained. Such behavior is explained by the complex interaction of polypyrrole and hydrogen peroxide produced by the oxygen reduction reaction. The electrochemical characteristics are compared with the zinc-manganese dioxide and zinc-air systems.

  4. Lanthanum manganite-based air electrode for solid oxide fuel cells

    DOEpatents

    Ruka, R.J.; Kuo, L.; Li, B.

    1999-06-29

    An air electrode material for a solid oxide fuel cell is disclosed. The electrode material is based on lanthanum manganite having a perovskite-like crystal structure ABO[sub 3]. The A-site of the air electrode material preferably comprises La, Ca, Ce and at least one lanthanide selected from Sm, Gd, Dy, Er, Y and Nd. The B-site of the electrode material comprises Mn with substantially no dopants. The ratio of A:B is preferably slightly above 1. A preferred air electrode composition is of the formula La[sub w]Ca[sub x]Ln[sub y]Ce[sub z]MnO[sub 3], wherein Ln comprises at least one lanthanide selected from Sm, Gd, Dy, Er, Y and Nd, w is from about 0.55 to about 0.56, x is from about 0.255 to about 0.265, y is from about 0.175 to about 0.185, and z is from about 0.005 to about 0.02. The air electrode material possesses advantageous chemical and electrical properties as well as favorable thermal expansion and thermal cycle shrinkage characteristics. 10 figs.

  5. Lanthanum manganite-based air electrode for solid oxide fuel cells

    DOEpatents

    Ruka, Roswell J.; Kuo, Lewis; Li, Baozhen

    1999-01-01

    An air electrode material for a solid oxide fuel cell is disclosed. The electrode material is based on lanthanum manganite having a perovskite-like crystal structure ABO.sub.3. The A-site of the air electrode material preferably comprises La, Ca, Ce and at least one lanthanide selected from Sm, Gd, Dy, Er, Y and Nd. The B-site of the electrode material comprises Mn with substantially no dopants. The ratio of A:B is preferably slightly above 1. A preferred air electrode composition is of the formula La.sub.w Ca.sub.x Ln.sub.y Ce.sub.z MnO.sub.3, wherein Ln comprises at least one lanthanide selected from Sm, Gd, Dy, Er, Y and Nd, w is from about 0.55 to about 0.56, x is from about 0.255 to about 0.265, y is from about 0.175 to about 0.185, and z is from about 0.005 to about 0.02. The air electrode material possesses advantageous chemical and electrical properties as well as favorable thermal expansion and thermal cycle shrinkage characteristics.

  6. A study of the glow discharge characteristics of contact electrodes at atmospheric pressure in air

    SciTech Connect

    Liu, Wenzheng Sun, Guangliang Li, Chuanhui; Zhang, Rongrong

    2014-04-15

    Electric field distributions and discharge properties of rod-rod contact electrodes were studied under the condition of DBD for the steady generation of atmospheric pressure glow discharge plasma (APGD) in air. We found that under the effect of the initial electrons generated in a nanometer-scale gap, the rod-rod cross-contact electrodes yielded APGD plasma in air. Regarding the rod-rod cross-contact electrodes, increasing the working voltage expanded the strong electric field area of the gas gap so that both discharge area and discharge power increased, and the increase in the number of contact points kept the initial discharge voltage unchanged and caused an increase in the plasma discharge area and discharge power. A mesh-like structure of cross-contact electrodes was designed and used to generate more APGD plasma, suggesting high applicability.

  7. Characterization of gas diffusion electrodes for metal-air batteries

    NASA Astrophysics Data System (ADS)

    Danner, Timo; Eswara, Santhana; Schulz, Volker P.; Latz, Arnulf

    2016-08-01

    Gas diffusion electrodes are commonly used in high energy density metal-air batteries for the supply of oxygen. Hydrophobic binder materials ensure the coexistence of gas and liquid phase in the pore network. The phase distribution has a strong influence on transport processes and electrochemical reactions. In this article we present 2D and 3D Rothman-Keller type multiphase Lattice-Boltzmann models which take into account the heterogeneous wetting behavior of gas diffusion electrodes. The simulations are performed on FIB-SEM 3D reconstructions of an Ag model electrode for predefined saturation of the pore space with the liquid phase. The resulting pressure-saturation characteristics and transport correlations are important input parameters for modeling approaches on the continuum scale and allow for an efficient development of improved gas diffusion electrodes.

  8. Reversible air electrodes integrated with an anion-exchange membrane for secondary air batteries

    NASA Astrophysics Data System (ADS)

    Fujiwara, Naoko; Yao, Masaru; Siroma, Zyun; Senoh, Hiroshi; Ioroi, Tsutomu; Yasuda, Kazuaki

    Reversible air electrodes integrated with a polymer electrolyte membrane have been proposed for use in rechargeable metal-air batteries or unitized regenerative fuel cells to reduce the impact of atmospheric carbon dioxide. Reversible air electrodes were prepared with an anion-exchange membrane (AEM) as a polymer electrolyte membrane and platinum-based catalysts. The AEM at the interface between the alkaline electrolyte and the air electrode layer plays major roles in AEM-type air electrodes as follows: it blocks (a) the permeation of cations in the alkaline electrolyte into the air electrode layer to prevent carbonate precipitation, (b) penetration of the alkaline solution itself, and (c) neutralization of the alkaline electrolyte by carbon dioxide, all of which prevent performance degradation of oxygen reactions. Catalysts for decreasing the overvoltage of oxygen reactions were also investigated with the AEM-type air electrode, and the overall efficiency was improved due to a remarkable decrease in the potential for the oxygen evolution reaction with Pt-Ir catalysts.

  9. Air-Supported Structures.

    ERIC Educational Resources Information Center

    Ontario Dept. of Education, Toronto. School Planning and Building Research Section.

    This study has been prepared to set out some of the benefits and the problems involved in the use of air-supported structures. Also indicated are the types of inquiries that should be made when the use of such structures is being considered. Technical and engineering details, such as the properties of various fabrics, are not included. (Author)

  10. Bifunctional air electrodes containing elemental iron powder charging additive

    DOEpatents

    Liu, Chia-tsun; Demczyk, Brian G.; Gongaware, Paul R.

    1982-01-01

    A bifunctional air electrode for use in electrochemical energy cells is made, comprising a hydrophilic layer and a hydrophobic layer, where the hydrophilic layer essentially comprises a hydrophilic composite which includes: (i) carbon; (ii) elemental iron particles having a particle size of between about 25 microns and about 700 microns diameter; (iii) an oxygen evolution material; (iv) a nonwetting agent; and (v) a catalyst, where at least one current collector is formed into said composite.

  11. Novel air electrode for metal-air battery with new carbon material and method of making same

    DOEpatents

    Ross, P.N. Jr.

    1988-06-21

    This invention relates to a rechargeable battery or fuel cell. More particularly, this invention relates to a novel air electrode comprising a new carbon electrode support material and a method of making same. 3 figs.

  12. Raman structural studies of the nickel electrode

    NASA Technical Reports Server (NTRS)

    Cornilsen, Bahne C.

    1994-01-01

    The objectives of this investigation have been to define the structures of charged active mass, discharged active mass, and related precursor materials (alpha-phases), with the purpose of better understanding the chemical and electrochemical reactions, including failure mechanisms and cobalt incorporation, so that the nickel electrode may be improved. Although our primary tool has been Raman spectroscopy, the structural conclusions drawn from the Raman data have been supported and augmented by three other analysis methods: infrared spectroscopy, powder X-ray Diffraction (XRD), and x-ray absorption spectroscopy (in particular EXAFS, Extended X-ray Absorption Fine Structure spectroscopy).

  13. Raman structural studies of the nickel electrode

    NASA Technical Reports Server (NTRS)

    Cornilsen, B. C.

    1985-01-01

    Raman spectroscopy is sensitive to empirically controlled nickel electrode structural variations, and has unique potential for structural characterization of these materials. How the structure relates to electrochemical properties is examined so that the latter can be more completely understood, controlled, and optimized. Electrodes were impregnated and cycled, and cyclic voltammetry is being used for electrochemical characterization. Structural variation was observed which has escaped detection using other methods. Structural changes are induced by: (1) cobalt doping, (2) the state of change or discharge, (3) the preparation conditions and type of buffer used, and (4) the formation process. Charged active mass has an NiOOH-type structure, agreeing with X-ray diffraction results. Discharged active mass, however, is not isostructural with beta-Ni(OH)2. Chemically prepared alpha phases are not isostructural either. A disordered structural model, containing point defects, is proposed for the cycled materials. This model explains K(+) incorporation. Band assignments were made and spectra interpreted for beta-Ni(OH)2, electrochemical NiOOH and chemically precipitated NiOOH.

  14. Air cathode structure manufacture

    DOEpatents

    Momyer, William R.; Littauer, Ernest L.

    1985-01-01

    An improved air cathode structure for use in primary batteries and the like. The cathode structure includes a matrix active layer, a current collector grid on one face of the matrix active layer, and a porous, nonelectrically conductive separator on the opposite face of the matrix active layer, the collector grid and separator being permanently bonded to the matrix active layer. The separator has a preselected porosity providing low IR losses and high resistance to air flow through the matrix active layer to maintain high bubble pressure during operation of the battery. In the illustrated embodiment, the separator was formed of porous polypropylene. A thin hydrophobic film is provided, in the preferred embodiment, on the current collecting metal grid.

  15. Novel configuration of bifunctional air electrodes for rechargeable zinc-air batteries

    NASA Astrophysics Data System (ADS)

    Li, Po-Chieh; Chien, Yu-Ju; Hu, Chi-Chang

    2016-05-01

    A novel configuration of two electrodes containing electrocatalysts for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) pressed into a bifunctional air electrode is designed for rechargeable Zn-air batteries. MOC/25BC carbon paper (MOC consisting of α-MnO2 and XC-72 carbon black) and Fe0.1Ni0.9Co2O4/Ti mesh on this air electrode mainly serve as the cathode for the ORR and the anode for the OER, respectively. The morphology and physicochemical properties of Fe0.1Ni0.9Co2O4 are investigated through scanning electron microscopy, inductively coupled plasma-mass spectrometry, and X-ray diffraction. Electrochemical studies comprise linear sweep voltammetry, rotating ring-disk electrode voltammetry, and the full-cell charge-discharge-cycling test. The discharge peak power density of the Zn-air battery with the unique air electrode reaches 88.8 mW cm-2 at 133.6 mA cm-2 and 0.66 V in an alkaline electrolyte under an ambient atmosphere. After 100 charge-discharge cycles at 10 mA cm-2, an increase of 0.3 V between charge and discharge cell voltages is observed. The deep charge-discharge curve (10 h in each step) indicates that the cell voltages of discharge (1.3 V) and charge (1.97 V) remain constant throughout the process. The performance of the proposed rechargeable Zn-air battery is superior to that of most other similar batteries reported in recent studies.

  16. Organic light emitting diodes with structured electrodes

    SciTech Connect

    Mao, Samuel S.; Liu, Gao; Johnson, Stephen G.

    2012-12-04

    A cathode that contain nanostructures that extend into the organic layer of an OLED has been described. The cathode can have an array of nanotubes or a layer of nanoclusters extending out from its surface. In another arrangement, the cathode is patterned and etched to form protruding nanostructures using a standard lithographic process. Various methods for fabricating these structures are provided, all of which are compatible with large-scale manufacturing. OLEDs made with these novel electrodes have greatly enhanced electron injection, have good environmental stability.

  17. AIR STRUCTURES FOR SCHOOL SPORTS.

    ERIC Educational Resources Information Center

    ROBERTSON, NAN

    AIR STRUCTURES ARE FABRIC BUILDINGS BLOWN UP AND HELD UP BY AIR PRESSURE. EXPERIMENTS WITH SUCH STRUCTURES WERE CONDUCTED AS EARLY AS 1917. IN 1948 THE UNITED STATES AIR FORCE SOUGHT A NEW WAY OF HOUSING LARGE RADAR ANTENNAE PLANNED FOR THE ARCTIC. AS AN OUTCOME OF THEIR SEARCH, BIRDAIR STRUCTURES, INC., WHICH IS NOW ONE OF SEVERAL COMPANIES…

  18. Air Structures for School Sports.

    ERIC Educational Resources Information Center

    Robertson, Nan

    Air structures are fabric buildings blown up and held up by air pressure. Experiments with such structures were conducted as early as 1917. In 1948 the United States Air Force sought a new way of housing large radar antennae planned for the arctic. As an outcome of their search, Birdair Structures, Inc., which is now one of several companies…

  19. PEDOT:PSS as multi-functional composite material for enhanced Li-air-battery air electrodes

    PubMed Central

    Yoon, Dae Ho; Yoon, Seon Hye; Ryu, Kwang-Sun; Park, Yong Joon

    2016-01-01

    We propose PEDOT:PSS as a multi-functional composite material for an enhanced Li-air-battery air electrode. The PEDOT:PSS layer was coated on the surface of carbon (graphene) using simple method. A electrode containing PEDOT:PSS-coated graphene (PEDOT electrode) could be prepared without binder (such as PVDF) because of high adhesion of PEDOT:PSS. PEDOT electrode presented considerable discharge and charge capacity at all current densities. These results shows that PEDOT:PSS acts as a redox reaction matrix and conducting binder in the air electrode. Moreover, after cycling, the accumulation of reaction products due to side reaction in the electrode was significantly reduced through the use of PEDOT:PSS. This implies that PEDOT:PSS coating layer can suppress the undesirable side reactions between the carbon and electrolyte (and/or Li2O2), which causes enhanced Li-air cell cyclic performance. PMID:26813852

  20. New insights into the electrode mechanism of lithium sulfur batteries via air-free post-test analysis.

    PubMed

    Chen, Lin; Dietz Rago, Nancy L; Bloom, Ira D; Shaw, Leon L

    2016-08-02

    Effects of the volume expansion and shrinkage of Li2S cathodes on electrochemical cycle life are investigated via post-test analysis without exposure to air. The engineered electrodes that confine volume changes within micro-reactors have significantly longer life than the electrodes without the micro-reactor structure, providing the first unambiguous evidence of the importance of confining volume changes for improved battery performance.

  1. Carbon-based air electrodes carrying MnO 2 in zinc-air batteries

    NASA Astrophysics Data System (ADS)

    Wei, Zidong; Huang, Wenzhang; Zhang, Shengtao; Tan, Jun

    Catalysts prepared from the carbon black impregnated with manganous nitrate solution and then heated at temperature from 270°C to 450°C were investigated. It was found that the impregnated catalysts heated at temperature of 340°C exhibited the best catalytic activity for oxygen reduction in alkaline electrolyte. It was also found that the XRD spectra of pyrolytic MnO 2 from manganous nitrate over 340°C were different from those below 340°C. The enhanced catalysis of air electrodes was ascribed to the formation of MnO 2 crystal with d-value of 2.72 Å as the impregnated-catalysts was heated at temperature of 340°C. The other factors in preparation of air electrodes were also discussed.

  2. Dielectric barrier structure with hollow electrodes and its recoil effect

    SciTech Connect

    Yu, Shuang; Chen, Qunzhi; Liu, Jiahui; Wang, Kaile; Jiang, Zhe; Sun, Zhili; Zhang, Jue; Fang, Jing

    2015-06-15

    A dielectric barrier structure with hollow electrodes (HEDBS), in which gas flow oriented parallel to the electric field, was proposed. Results showed that with this structure, air can be effectively ignited, forming atmospheric low temperature plasma, and the proposed HEDBS could achieve much higher electron density (5 × 10{sup 15}/cm{sup 3}). It was also found that the flow condition, including outlet diameter and flow rate, played a key role in the evolution of electron density. Optical emission spectroscopy diagnostic results showed that the concentration of reactive species had the same variation trend as the electron density. The simulated distribution of discharge gas flow indicated that the HEDBS had a strong recoil effect on discharge gas, and could efficiently promote generating electron density as well as reactive species.

  3. Studies on the oxygen reduction catalyst for zinc-air battery electrode

    NASA Astrophysics Data System (ADS)

    Wang, Xianyou; Sebastian, P. J.; Smit, Mascha A.; Yang, Hongping; Gamboa, S. A.

    In this paper, perovskite type La 0.6Ca 0.4CoO 3 as a catalyst of oxygen reduction was prepared, and the structure and performance of the catalysts was examined by means of IR, X-ray diffraction (XRD), and thermogravimetric (TG). Mixed catalysts doped, some metal oxides were put also used. The cathodic polarization curves for oxygen reduction on various catalytic electrodes were measured by linear sweep voltammetry (LSV). A Zn-air battery was made with various catalysts for oxygen reduction, and the performance of the battery was measured with a BS-9300SM rechargeable battery charge/discharge device. The results showed that the perovskite type catalyst (La 0.6Ca 0.4CoO 3) doped with metal oxide is an excellent catalyst for the zinc-air battery, and can effectively stimulate the reduction of oxygen and improve the properties of zinc-air batteries, such as discharge capacity, etc.

  4. The structure of hydrophobic gas diffusion electrodes.

    NASA Technical Reports Server (NTRS)

    Giner, J.

    1972-01-01

    The 'flooded agglomerate' model of the Teflon-bonded gas diffusion electrode is discussed. A mathematical treatment of the 'flooded agglomerate' model is given; it can be used to predict the performance of the electrode as a function of measurable physical parameters.

  5. Electrode structures and surfaces for Li batteries

    DOEpatents

    Thackeray, Michael M.; Kang, Sun-Ho; Balasubramanian, Mahalingam; Croy, Jason

    2017-03-14

    This invention relates to methods of preparing positive electrode materials for electrochemical cells and batteries. It relates, in particular, to a method for fabricating lithium-metal-oxide electrode materials for lithium cells and batteries. The method comprises contacting a hydrogen-lithium-manganese-oxide material with one or more metal ions, preferably in an acidic solution, to insert the one or more metal ions into the hydrogen-lithium-manganese-oxide material; heat-treating the resulting product to form a powdered metal oxide composition; and forming an electrode from the powdered metal oxide composition.

  6. Ion flow and sheath structure near positively biased electrodes

    NASA Astrophysics Data System (ADS)

    Hood, R.; Scheiner, B.; Baalrud, S. D.; Hopkins, M. M.; Barnat, E. V.; Yee, B. T.; Merlino, R. L.; Skiff, F.

    2016-11-01

    What effect does a dielectric material surrounding a small positively biased electrode have on the ion flow and sheath structure near the electrode? Measurements of the ion velocity distribution function and plasma potential near positively biased electrodes were made using laser-induced fluorescence and an emissive probe. The results were compared with 2D particle-in-cell simulations. Both measurements and simulations showed that when the positive electrode was surrounded by the dielectric material, ions were accelerated toward the electrode to approximately 0.5 times the ion sound speed before being deflected radially by the electron sheath potential barrier of the electrode. The axial potential profile in this case contained a virtual cathode. In comparison, when the dielectric material was removed from around the electrode, both the ion flow and virtual cathode depth near the electrode were dramatically reduced. These measurements suggest that the ion presheath from the dielectric material surrounding the electrode may enclose the electron sheath of the electrode, resulting in a virtual cathode that substantially influences the ion flow profile in the region.

  7. Novel air electrode for metal-air battery with new carbon material and method of making same

    DOEpatents

    Ross, Jr., Philip N.

    1990-01-01

    A novel carbonaceous electrode support material is disclosed characterized by a corrosion rate of 0.03 wt. %/hour or less when measured a5 550 millivolts vs. a Hg/HgO electrode in a 30 wt. % KOH electrolyte a5 30.degree. C. The electrode support material comprises a preselected carbon black material which has been heat-treated by heating the material to a temperature of from about 2500.degree. to about 3000.degree. C. over a period of from about 1 to about 5 hours in an inert atmosphere and then maintaining the preselected carbon black material at this temperature for a period of at least about 1 hour, and preferably about 2 hours, in the inert atmosphere. A carbonaceous electrode suitable for use as an air electrode in a metal-air cell may be made from the electrode support material by shaping and forming it into a catalyst support and then impregnating it with a catalytically active material capable of catalyzing the reaction with oxygen at the air electrode of metal-air cell.

  8. New electrode-barrier structures for high density ferroelectric memories

    NASA Astrophysics Data System (ADS)

    Vedula, R.; Desu, C. S.; Tirumala, S.; Bhatt, H. D.; Desu, S. B.; Lee, K. B.

    2001-03-01

    In this paper, two electrode-barrier structures based on Pt-Rh and Pt-Ir alloys and their oxides are proposed for high-density ferroelectric memory applications. These electrode-barriers are multi-layered, comprising a diffusion barrier (PtRhOx or PtIrOx), metal alloy (PtRh or PtIr) and another PtRhOx or PtIrOx layer for fatigue reduction in the case of PZT capacitors. Both lead zirconate titanate (PZT) and strontium bismuth tantalate (SBT) capacitors based on the electrode-barriers were used in the present study. The electrode-barrier structure acts as a conducting electrode as well as an excellent diffusion barrier for lead, bismuth, oxygen and silicon. The PZT test capacitors fabricated on these electrode-barriers showed excellent fatigue resistance with other ferroelectric properties being similar to those on Pt. Also, these electrode-barriers are stable, and remain conductive even up to the processing temperatures of SBT (750 °C). This makes direct integration of both PZT and SBT capacitors on to a poly-Si plug attainable. In addition, the conducting electrode-barrier structures can be deposited in situ, directly over n+polycrystalline Si, thereby significantly improving the density of the device.

  9. Stability in alkaline aqueous electrolyte of air electrode protected with fluorinated interpenetrating polymer network membrane

    NASA Astrophysics Data System (ADS)

    Bertolotti, Bruno; Messaoudi, Houssam; Chikh, Linda; Vancaeyzeele, Cédric; Alfonsi, Séverine; Fichet, Odile

    2015-01-01

    We developed original anion exchange membranes to protect air electrodes operating in aqueous lithium-air battery configuration, i.e. supplied with atmospheric air and in concentrated aqueous lithium hydroxide. These protective membranes have an interpenetrating polymer network (IPN) architecture combining a hydrogenated cationic polyelectrolyte network based on poly(epichlorohydrin) (PECH) and a fluorinated neutral network based on perfluoropolyether (Fluorolink® MD700). Two phases, each one rich in one of the polymer, are co-continuous in the materials. This morphology allows combining their properties according to the weight proportions of each polymer. Thus, PECH/Fluorolink IPNs show ionic conductivity varying from 1 to 2 mS cm-1, water uptake from 30 to 90 wt.% and anionic transport number from 0.65 to 0.80 when the PECH proportion varies from 40 to 90 wt.%. These membranes have been systematically assembled on air electrodes. Air electrode protected with PECH/Fluorolink 70/30 IPN shows outstanding stability higher than 1000 h, i.e. a 20-fold increase in the lifetime of the non-modified electrode. This efficient membrane/air electrode assembly is promising for development of alkaline electrolyte based storage or production energy systems, such as metal air batteries or alkaline fuel cells.

  10. Surface modification of active material structures in battery electrodes

    DOEpatents

    Erickson, Michael; Tikhonov, Konstantin

    2016-02-02

    Provided herein are methods of processing electrode active material structures for use in electrochemical cells or, more specifically, methods of forming surface layers on these structures. The structures are combined with a liquid to form a mixture. The mixture includes a surface reagent that chemically reacts and forms a surface layer covalently bound to the structures. The surface reagent may be a part of the initial liquid or added to the mixture after the liquid is combined with the structures. In some embodiments, the mixture may be processed to form a powder containing the structures with the surface layer thereon. Alternatively, the mixture may be deposited onto a current collecting substrate and dried to form an electrode layer. Furthermore, the liquid may be an electrolyte containing the surface reagent and a salt. The liquid soaks the previously arranged electrodes in order to contact the structures with the surface reagent.

  11. Performance and microbial ecology of air-cathode microbial fuel cells with layered electrode assemblies.

    PubMed

    Butler, Caitlyn S; Nerenberg, Robert

    2010-05-01

    Microbial fuel cells (MFCs) can be built with layered electrode assemblies, where the anode, proton exchange membrane (PEM), and cathode are pressed into a single unit. We studied the performance and microbial community structure of MFCs with layered assemblies, addressing the effect of materials and oxygen crossover on the community structure. Four MFCs with layered assemblies were constructed using Nafion or Ultrex PEMs and a plain carbon cloth electrode or a cathode with an oxygen-resistant polytetrafluoroethylene diffusion layer. The MFC with Nafion PEM and cathode diffusion layer achieved the highest power density, 381 mW/m(2) (20 W/m(3)). The rates of oxygen diffusion from cathode to anode were three times higher in the MFCs with plain cathodes compared to those with diffusion-layer cathodes. Microsensor studies revealed little accumulation of oxygen within the anode cloth. However, the abundance of bacteria known to use oxygen as an electron acceptor, but not known to have exoelectrogenic activity, was greater in MFCs with plain cathodes. The MFCs with diffusion-layer cathodes had high abundance of exoelectrogenic bacteria within the genus Geobacter. This work suggests that cathode materials can significantly influence oxygen crossover and the relative abundance of exoelectrogenic bacteria on the anode, while PEM materials have little influence on anode community structure. Our results show that oxygen crossover can significantly decrease the performance of air-cathode MFCs with layered assemblies, and therefore limiting crossover may be of particular importance for these types of MFCs.

  12. Performance and cycle life of carbon- and conductive-based air electrodes for rechargeable Zn-air battery applications

    NASA Astrophysics Data System (ADS)

    Chellapandi Velraj, Samgopiraj

    The development of high-performance, cyclically stable bifunctional air electrodes are critical to the commercial deployment of rechargeable Zn-air batteries. The carbon material predominantly used as support material in the air electrodes due to its higher surface area and good electrical conductivity suffers from corrosion at high oxygen evolution overpotentials. This study addresses the carbon corrosion issues and suggests alternate materials to replace the carbon as support in the air electrode. In this study, Sm0.5Sr0.5CoO3-delta with good electrochemical performance and cyclic lifetime was identified as an alternative catalyst material to the commonly used La0.4Ca 0.6CoO3 catalyst for the carbon-based bifunctional electrodes. Also, a comprehensive study on the effects of catalyst morphology, testing conditions on the cycle life as well as the relevant degradation mechanism for the carbon-based electrode was conducted in this dissertation. The cyclic life of the carbon-based electrodes was strongly dependent on the carbon support material, while the degradation mechanisms were entirely controlled by the catalyst particle size/morphology. Some testing conditions like resting time and electrolyte concentration did not change the cyclic life or degradation mechanism of the carbon-based electrode. The current density used for cyclic testing was found to dictate the degradation mechanism leading to the electrode failure. An alternate way to circumvent the carbon corrosion is to replace the carbon support with a suitable electrically-conductive ceramic material. In this dissertation, LaNi0.9Mn0.1O3, LaNi 0.8Co0.2O3, and NiCo2O4 were synthesized and evaluated as prospective support materials due to their good electrical conductivity and their ability to act as the catalyst needed for the bifunctional electrode. The carbon-free electrodes had remarkably higher catalytic activity for oxygen evolution reaction (OER) when compared to the carbon-based electrode. However

  13. Equivalent ambipolar carrier injection of electrons and holes with Au electrodes in air-stable field effect transistors

    SciTech Connect

    Kanagasekaran, Thangavel E-mail: Shimotani@m.tohoku.ac.jp Ikeda, Susumu; Kumashiro, Ryotaro; Shimotani, Hidekazu E-mail: Shimotani@m.tohoku.ac.jp Shang, Hui; Tanigaki, Katsumi E-mail: Shimotani@m.tohoku.ac.jp

    2015-07-27

    Carrier injection from Au electrodes to organic thin-film active layers can be greatly improved for both electrons and holes by nano-structural surface control of organic semiconducting thin films using long-chain aliphatic molecules on a SiO{sub 2} gate insulator. In this paper, we demonstrate a stark contrast for a 2,5-bis(4-biphenylyl)bithiophene (BP2T) active semiconducting layer grown on a modified SiO{sub 2} dielectric gate insulator between two different modifications of tetratetracontane and poly(methyl methacrylate) thin films. Important evidence that the field effect transistor (FET) characteristics are independent of electrode metals with different work functions is given by the observation of a conversion of the metal-semiconductor contact from the Schottky limit to the Bardeen limit. An air-stable light emitting FET with an Au electrode is demonstrated.

  14. Virtual electrodes around anatomical structures and their roles in defibrillation

    PubMed Central

    Vigmond, Edward; Bishop, Martin

    2017-01-01

    Background Virtual electrodes from structural/conductivity heterogeneities are known to elicit wavefront propagation, upon field-stimulation, and are thought to be important for defibrillation. In this work we investigate how the constitutive and geometrical parameters associated with such anatomical heterogeneities, represented by endo/epicardial surfaces and intramural surfaces in the form of blood-vessels, affect the virtual electrode patterns produced. Methods and results The steady-state bidomain model is used to obtain, using analytical and numerical methods, the virtual electrode patterns created around idealized endocardial trabeculations and blood-vessels. The virtual electrode pattern around blood-vessels is shown to be composed of two dominant effects; current traversing the vessel surface and conductivity heterogeneity from the fibre-architecture. The relative magnitudes of these two effects explain the swapping of the virtual electrode polarity observed, as a function of the vessel radius, and aid in the understanding of the virtual electrode patterns predicted by numerical bidomain modelling. The relatively high conductivity of blood, compared to myocardium, is shown to cause stronger depolarizations in the endocardial trabeculae grooves than the protrusions. Conclusions The results provide additional quantitative understanding of the virtual electrodes produced by small-scale ventricular anatomy, and highlight the importance of faithfully representing the physiology and the physics in the context of computational modelling of field stimulation. PMID:28253365

  15. Stretchable and transparent electrodes based on in-plane structures

    NASA Astrophysics Data System (ADS)

    Kim, Kukjoo; Kim, Joohee; Hyun, Byung Gwan; Ji, Sangyoon; Kim, So-Yun; Kim, Sungwon; An, Byeong Wan; Park, Jang-Ung

    2015-08-01

    Stretchable electronics has attracted great interest with compelling potential applications that require reliable operation under mechanical deformation. Achieving stretchability in devices, however, requires a deeper understanding of nanoscale materials and mechanics beyond the success of flexible electronics. In this regard, tremendous research efforts have been dedicated toward developing stretchable electrodes, which are one of the most important building blocks for stretchable electronics. Stretchable transparent thin-film electrodes, which retain their electrical conductivity and optical transparency under mechanical deformation, are particularly important for the favourable application of stretchable devices. This minireview summarizes recent advances in stretchable transparent thin-film electrodes, especially employing strategies based on in-plane structures. Various approaches using metal nanomaterials, carbon nanomaterials, and their hybrids are described in terms of preparation processes and their optoelectronic/mechanical properties. Some challenges and perspectives for further advances in stretchable transparent electrodes are also discussed.

  16. Electrode structure and method for making the same

    DOEpatents

    Affinito, John D.; Lowe, Gregory K.

    2015-05-26

    Electrode structures, and more specifically, electrode structures for use in electrochemical cells, are provided. The electrode structures described herein may include one or more protective layers. In one set of embodiments, a protective layer may be formed by exposing a lithium metal surface to a plasma comprising ions of a gas to form a ceramic layer on top of the lithium metal. The ceramic layer may be highly conductive to lithium ions and may protect the underlying lithium metal surface from reaction with components in the electrolyte. In some cases, the ions may be nitrogen ions and a lithium nitride layer may be formed on the lithium metal surface. In other embodiments, the protective layer may be formed by converting lithium to lithium nitride at high pressures. Other methods for forming protective layers are also provided.

  17. Fabrication of dual porosity electrode structure

    DOEpatents

    Smith, J.L.; Kucera, E.H.

    1991-02-12

    A substantially entirely fibrous ceramic is described which may have dual porosity of both micro and macro pores. Total porosity may be 60-75% by volume. A method of spraying a slurry perpendicularly to an ambient stream of air is disclosed along with a method of removing binders without altering the fiber morphology. Adding fine ceramic particulates to the green ceramic fibers enhances the sintering characteristics of the fibers. 3 figures.

  18. Fabrication of dual porosity electrode structure

    DOEpatents

    Smith, James L.; Kucera, Eugenia H.

    1991-01-01

    A substantially entirely fibrous ceramic which may have dual porosity of both micro and macro pores. Total porosity may be 60-75% by volume. A method of spraying a slurry perpendicularly to an ambient stream of air is disclosed along with a method of removing binders without altering the fiber morphology. Adding fine ceramic particulates to the green ceramic fibers enhances the sintering characteristics of the fibers.

  19. Porous carbonaceous electrode structure and method for secondary electrochemical cell

    DOEpatents

    Kaun, Thomas D.

    1977-03-08

    Positive and negative electrodes are provided as rigid, porous carbonaceous matrices with particulate active material fixedly embedded. Active material such as metal chalcogenides, solid alloys of alkali metal or alkaline earth metals along with other metals and their oxides in particulate form are blended with a thermosetting resin and a solid volatile to form a paste mixture. Various electrically conductive powders or current collector structures can be blended or embedded into the paste mixture which can be molded to the desired electrode shape. The molded paste is heated to a temperature at which the volatile transforms into vapor to impart porosity as the resin begins to cure into a rigid solid structure.

  20. CNT Sheet Air Electrode for the Development of Ultra-High Cell Capacity in Lithium-Air Batteries

    PubMed Central

    Nomura, Akihiro; Ito, Kimihiko; Kubo, Yoshimi

    2017-01-01

    Lithium-air batteries (LABs) are expected to provide a cell with a much higher capacity than ever attained before, but their prototype cells present a limited areal cell capacity of no more than 10 mAh cm−2, mainly due to the limitation of their air electrodes. Here, we demonstrate the use of flexible carbon nanotube (CNT) sheets as a promising air electrode for developing ultra-high capacity in LAB cells, achieving areal cell capacities of up to 30 mAh cm−2, which is approximately 15 times higher than the capacity of cells with lithium-ion battery (LiB) technology (~2 mAh cm−2). During discharge, the CNT sheet electrode experienced enormous swelling to a thickness of a few millimeters because of the discharge product deposition of lithium peroxide (Li2O2), but the sheet was fully recovered after being fully charged. This behavior results from the CNT sheet characteristics of the flexible and fibrous conductive network and suggests that the CNT sheet is an effective air electrode material for developing a commercially available LAB cell with an ultra-high cell capacity. PMID:28378746

  1. Low resistance fuel electrodes

    DOEpatents

    Maskalick, Nichols J.; Folser, George R.

    1989-01-01

    An electrode 6 bonded to a solid, ion conducting electrolyte 5 is made, where the electrode 6 comprises a ceramic metal oxide 18, metal particles 17, and heat stable metal fibers 19, where the metal fibers provide a matrix structure for the electrode. The electrolyte 5 can be bonded to an air electrode cathode 4, to provide an electrochemical cell 2, preferably of tubular design.

  2. Fuel Cell Electrodes for Hydrogen-Air Fuel Cell Assemblies.

    DTIC Science & Technology

    The report describes the design and evaluation of a hydrogen-air fuel cell module for use in a portable hydrid fuel cell -battery system. The fuel ... cell module consists of a stack of 20 single assemblies. Each assembly contains 2 electrically independent cells with a common electrolyte compartment

  3. Low cost stable air electrode material for high temperature solid oxide electrolyte electrochemical cells

    DOEpatents

    Kuo, Lewis J. H.; Singh, Prabhakar; Ruka, Roswell J.; Vasilow, Theodore R.; Bratton, Raymond J.

    1997-01-01

    A low cost, lanthanide-substituted, dimensionally and thermally stable, gas permeable, electrically conductive, porous ceramic air electrode composition of lanthanide-substituted doped lanthanum manganite is provided which is used as the cathode in high temperature, solid oxide electrolyte fuel cells and generators. The air electrode composition of this invention has a much lower fabrication cost as a result of using a lower cost lanthanide mixture, either a natural mixture or an unfinished lanthanide concentrate obtained from a natural mixture subjected to incomplete purification, as the raw material in place of part or all of the higher cost individual lanthanum. The mixed lanthanide primarily contains a mixture of at least La, Ce, Pr, and Nd, or at least La, Ce, Pr, Nd and Sm in its lanthanide content, but can also include minor amounts of other lanthanides and trace impurities. The use of lanthanides in place of some or all of the lanthanum also increases the dimensional stability of the air electrode. This low cost air electrode can be fabricated as a cathode for use in high temperature, solid oxide fuel cells and generators.

  4. Low cost stable air electrode material for high temperature solid oxide electrolyte electrochemical cells

    DOEpatents

    Kuo, L.J.H.; Singh, P.; Ruka, R.J.; Vasilow, T.R.; Bratton, R.J.

    1997-11-11

    A low cost, lanthanide-substituted, dimensionally and thermally stable, gas permeable, electrically conductive, porous ceramic air electrode composition of lanthanide-substituted doped lanthanum manganite is provided which is used as the cathode in high temperature, solid oxide electrolyte fuel cells and generators. The air electrode composition of this invention has a much lower fabrication cost as a result of using a lower cost lanthanide mixture, either a natural mixture or an unfinished lanthanide concentrate obtained from a natural mixture subjected to incomplete purification, as the raw material in place of part or all of the higher cost individual lanthanum. The mixed lanthanide primarily contains a mixture of at least La, Ce, Pr, and Nd, or at least La, Ce, Pr, Nd and Sm in its lanthanide content, but can also include minor amounts of other lanthanides and trace impurities. The use of lanthanides in place of some or all of the lanthanum also increases the dimensional stability of the air electrode. This low cost air electrode can be fabricated as a cathode for use in high temperature, solid oxide fuel cells and generators. 4 figs.

  5. Silver-Copper Nanoalloy Catalyst Layer for Bifunctional Air Electrodes in Alkaline Media.

    PubMed

    Wu, Xiaoqiang; Chen, Fuyi; Jin, Yachao; Zhang, Nan; Johnston, Roy L

    2015-08-19

    A carbon-free and binder-free catalyst layer composed of a Ag-Cu nanoalloy on Ni foam was used as the air cathode in a zinc-air battery for the first time. The Ag-Cu catalyst was prepared using pulsed laser deposition. The structures of the catalysts were found to consist of crystalline Ag-Cu nanoalloy particles with an average size of 2.58 nm embedded in amorphous Cu films. As observed in the X-ray photoelectron spectra, the Ag 3d core levels shifted to higher binding energies, whereas the Cu 2p core levels shifted to lower binding energies, indicating alloying of the silver and copper. Rotating disk electrode measurements indicated that the oxygen reduction reaction (ORR) proceeded through a four-electron pathway on the Ag50Cu50 and Ag90Cu10 nanoalloy catalysts in alkaline solution. Moreover, the catalytic activity of Ag50Cu50 in the ORR is more efficient than that of Ag90Cu10. By performing charge and discharge cycling measurements, the Ag50Cu50 catalyst layer was confirmed to have a maximum power density of approximately 86.3 mW cm(-2) and an acceptable cell voltage at 0.863 V for current densities up to 100 mA cm(-2) in primary zinc-air batteries. In addition, a round-trip efficiency of approximately 50% at a current density of 20 mA cm(-2) was also obtained in the test.

  6. Effects of atmospheric air plasma treatment of graphite and carbon felt electrodes on the anodic current from Shewanella attached cells.

    PubMed

    Epifanio, Monica; Inguva, Saikumar; Kitching, Michael; Mosnier, Jean-Paul; Marsili, Enrico

    2015-12-01

    The attachment of electrochemically active microorganisms (EAM) on an electrode is determined by both the chemistry and topography of the electrode surface. Pre-treatment of the electrode surface by atmospheric air plasma introduces hydrophilic functional groups, thereby increasing cell attachment and electroactivity in short-term experiments. In this study, we use graphite and carbon felt electrodes to grow the model EAM Shewanella loihica PV-4 at oxidative potential (0.2 V vs. Ag/AgCl). Cell attachment and electroactivity are measured through electrodynamic methods. Atmospheric air plasma pre-treatment increases cell attachment and current output at graphite electrodes by 25%, while it improves the electroactivity of the carbon felt electrodes by 450%. Air plasma pre-treatment decreased the coulombic efficiency on both carbon felt and graphite electrodes by 60% and 80%, respectively. Microbially produced flavins adsorb preferentially at the graphite electrode, and air plasma pre-treatment results in lower flavin adsorption at both graphite and carbon felt electrodes. Results show that air plasma pre-treatment is a feasible option to increase current output in bioelectrochemical systems.

  7. Long-range surface plasmons in electrode structures

    NASA Technical Reports Server (NTRS)

    Stegeman, G. I.; Burke, J. J.

    1983-01-01

    Surface polaritons guided by symmetric double metal film structures are analyzed, with particular attention given to the attenuation of the two long-range modes that occur. It is found that long-range surface plasmon polariton modes do exist for double electrode structures over a limited range of material parameters. Guided by thin metal electrodes, surface plasmon polaritons can achieve millimeter plus propagation distances in the near infrared. It is pointed out that if the slab is electrooptic, then very low voltages will be needed to manipulate the waves. The fact that long-range modes exist simultaneously with junction tunnel plasmons may be of use in providing directional radiation from light-emitting junctions or the inverse process of light to electrical energy conversion.

  8. Layered perovskite oxide: a reversible air electrode for oxygen evolution/reduction in rechargeable metal-air batteries.

    PubMed

    Takeguchi, Tatsuya; Yamanaka, Toshiro; Takahashi, Hiroki; Watanabe, Hiroshi; Kuroki, Tomohiro; Nakanishi, Haruyuki; Orikasa, Yuki; Uchimoto, Yoshiharu; Takano, Hiroshi; Ohguri, Nobuaki; Matsuda, Motofumi; Murota, Tadatoshi; Uosaki, Kohei; Ueda, Wataru

    2013-07-31

    For the development of a rechargeable metal-air battery, which is expected to become one of the most widely used batteries in the future, slow kinetics of discharging and charging reactions at the air electrode, i.e., oxygen reduction reaction (ORR) and oxygen evolution reaction (OER), respectively, are the most critical problems. Here we report that Ruddlesden-Popper-type layered perovskite, RP-LaSr3Fe3O10 (n = 3), functions as a reversible air electrode catalyst for both ORR and OER at an equilibrium potential of 1.23 V with almost no overpotentials. The function of RP-LaSr3Fe3O10 as an ORR catalyst was confirmed by using an alkaline fuel cell composed of Pd/LaSr3Fe3O10-2x(OH)2x·H2O/RP-LaSr3Fe3O10 as an open circuit voltage (OCV) of 1.23 V was obtained. RP-LaSr3Fe3O10 also catalyzed OER at an equilibrium potential of 1.23 V with almost no overpotentials. Reversible ORR and OER are achieved because of the easily removable oxygen present in RP-LaSr3Fe3O10. Thus, RP-LaSr3Fe3O10 minimizes efficiency losses caused by reactions during charging and discharging at the air electrode and can be considered to be the ORR/OER electrocatalyst for rechargeable metal-air batteries.

  9. Assemblies of protective anion exchange membrane on air electrode for its efficient operation in aqueous alkaline electrolyte

    NASA Astrophysics Data System (ADS)

    Bertolotti, Bruno; Chikh, Linda; Vancaeyzeele, Cédric; Alfonsi, Séverine; Fichet, Odile

    2015-01-01

    Aqueous alkaline metal-air batteries represent promising energy storage devices when supplied with atmospheric air. However, under this condition, the air electrode shows a very short life time (i.e. 50 h of operation in 5 M LiOH at -10 mA cm-2), mainly due to the precipitation of carbonates inside the electrode porosity. The air electrode can then be protected by an anion exchange membrane on the electrolyte side. In this paper, we demonstrate that the efficiency of this protective membrane depends on the assembly method on the electrode. When a modified poly(epichlorohydrin) (PECH) network is synthesized directly on the electrode, the polymer seeps inside the electrode porosity, and a suitable interface inducing negligible additional polarization in comparison with classical pressure-assembled membranes is obtained. This protected electrode shows improved stability of up to 160 h of operation in 5 M LiOH. This performance is improved to 350 h by adjusting the conductivity and the ionic exchange capacity. Finally, the interest of interpenetrating polymer network (IPN) architecture compared to a single network is confirmed. Indeed, an electrode protected with a PECH/poly(2-hydroxyethyl methacrylate) (PHEMA) IPN is stable for 650 h in 5 M LiOH. In addition, degradation process becomes reversible since the assembly can be regenerated, which is not possible for the bare electrode.

  10. Electrode

    SciTech Connect

    Clere, T.M.

    1983-08-30

    A 3-dimensional electrode is disclosed having substantially coplanar and substantially flat portions and ribbon-like curved portions, said curved portions being symmetrical and alternating in rows above and below said substantially coplanar, substantially flat portions, respectively, and a geometric configuration presenting in one sectional aspect the appearance of a series of ribbon-like oblate spheroids interrupted by said flat portions and in another sectional aspect, 90/sup 0/ from said one aspect, the appearance of a square wave pattern.

  11. Gas diffusion-type oxygen electrode using perovskite-type oxides for metal-air batteries

    SciTech Connect

    Hyodo, Takeo; Miura, Norio; Yamazoe, Noboru

    1995-12-31

    In order to develop an air cathode of metal-air batteries, oxygen reduction behavior of gas diffusion-type carbon electrodes loaded with perovskite-type oxides, La{sub 1{minus}x}A{prime}{sub x}FeO{sub 3} (A{prime} = Ca, Sr, Ba, 0 {le} x {le} 1.0), was examined in 8 M KOH at 60 C. Among the oxide catalysts tested, La{sub 0.5}Sr{sub 0.5}FeO{sub 3} (specific surface area: 21.5 m{sup 2}{center_dot}g{sup {minus}1}) gave the highest electrode performance. On the basis of electrode reaction kinetics, H{sub 2}O{sub 2} decomposition rates, and temperature programmed desorption of oxygen, it was concluded that such a performance was attributable to the active sites of the oxide for the direct 4-electron reduction of oxygen. Moreover, the electrode using La{sub 0.5}Sr{sub 0.5}FeO{sub 3} was found to be rather stable in a short-term operation for 90 h at 300 mA{center_dot}cm{sup {minus}2}.

  12. Stability of carbon electrodes for aqueous lithium-air secondary batteries

    NASA Astrophysics Data System (ADS)

    Ohkuma, Hirokazu; Uechi, Ichiro; Matsui, Masaki; Takeda, Yasuo; Yamamoto, Osamu; Imanishi, Nobuyuki

    2014-01-01

    The air electrode performance of various carbon materials, such as Ketjen black (KB), acetylene black (AB and AB-S), Vulcan XC-72R (VX), and vapor grown carbon fiber (VGCF) with and without La0.6Sr0.4Co0.2Fe0.8O3 (LSCF) catalyst were examined in an aqueous solution of saturated LiOH with 10 M LiCl in the current density range 0.2-2.0 mA cm-2. The best performance for oxygen reduction and evolution reactions was observed for the KB electrode, which has the highest surface area among the carbon materials examined. A steady over-potential of 0.2 V was obtained for the oxygen reduction reaction using the KB electrode without the catalyst, while the over-potential was 0.15 V for KB with the LSCF catalyst at 2.0 mA cm-2. The over-potentials for the oxygen evolution reaction were slightly higher than those for the oxygen reduction reaction, and gradually increased with the polarization period. Analysis of the gas in the cell after polarization above 0.4 V revealed the evolution of a small amount of CO during the oxygen evolution reaction by the decomposition of carbon in the electrode. The amount of CO evolved was significantly decreased by the addition of LSCF to the carbon electrode.

  13. Cobalt Phthalocyanine Modified Electrodes Utilised in Electroanalysis: Nano-Structured Modified Electrodes vs. Bulk Modified Screen-Printed Electrodes

    PubMed Central

    Foster, Christopher W.; Pillay, Jeseelan; Metters, Jonathan P.; Banks, Craig E.

    2014-01-01

    Cobalt phthalocyanine (CoPC) compounds have been reported to provide electrocatalytic performances towards a substantial number of analytes. In these configurations, electrodes are typically constructed via drop casting the CoPC onto a supporting electrode substrate, while in other cases the CoPC complex is incorporated within the ink of a screen-printed sensor, providing a one-shot economical and disposable electrode configuration. In this paper we critically compare CoPC modified electrodes prepared by drop casting CoPC nanoparticles (nano-CoPC) onto a range of carbon based electrode substrates with that of CoPC bulk modified screen-printed electrodes in the sensing of the model analytes l-ascorbic acid, oxygen and hydrazine. It is found that no “electrocatalysis” is observed towards l-ascorbic acid using either of these CoPC modified electrode configurations and that the bare underlying carbon electrode is the origin of the obtained voltammetric signal, which gives rise to useful electroanalytical signatures, providing new insights into literature reports where “electrocatalysis” has been reported with no clear control experiments undertaken. On the other hand true electrocatalysis is observed towards hydrazine, where no such voltammetric features are witnessed on the bare underlying electrode substrate. PMID:25414969

  14. Structural comparison of nickel electrodes and precursor phases

    NASA Technical Reports Server (NTRS)

    Cornilsen, Bahne C.; Shan, Xiaoyin; Loyselle, Patricia

    1989-01-01

    A summary of previous Raman spectroscopic results and a discussion of important structural differences in the various phases of active mass and active mass precurors are presented. Raman spectra provide unique signatures for these phases, and allow one to distinguish each phase, even when the compound is amorphous to X-rays (i.e., does not scatter X-rays because of a lack of order and/or small particle size). The structural changes incurred during formation, charge and discharge, cobalt addition, and aging will be discussed and related to electrode properties. Important structural differences include NiO2 layer stacking, nonstoichiometry (especially cation-deficit nonstoichiometry), disorder, dopant content, and water content. The results indicate that optimal nickel active mass is non-close packed and nonstoichiometric. The formation process transforms precursor phases into this structure. Therefore, the precursor disorder, or lack thereof, influences this final active mass structure and the rate of formation. Aging processes induce structural change which is believed to be detrimental. The role of cobalt addition can be appreciated in terms of structures favored or stabilized by the dopant. In recent work, the in situ Raman technique to characterize the critical structural parameters was developed. An in situ method relates structure, electrochemistry, and preparation. In situ Raman spectra of cells during charge and discharge, either during cyclic voltammetry or under constant current conditions were collected. With the structure-preparation knowledge and the in situ Raman tool, it will be possible to define the structure-property-preparation relations in more detail. This instrumentation has application to a variety of electrode systems.

  15. Air electrode material for high temperature electrochemical cells

    DOEpatents

    Ruka, Roswell J.

    1985-01-01

    Disclosed is a solid solution with a perovskite-like crystal structure having the general formula La.sub.1-x-w (M.sub.L).sub.x (Ce).sub.w (M.sub.S1).sub.1-y (M.sub.S2).sub.y O.sub.3 where M.sub.L is Ca, Sr, Ba, or mixtures thereof, M.sub.S1 is Mn, Cr, or mixtures thereof and M.sub.S2 is Ni, Fe, Co, Ti, Al, In, Sn, Mg, Y, Nb, Ta, or mixtures thereof, w is about 0.05 to about 0.25, x+w is about 0.1 to about 0.7, and y is 0 to about 0.5. In the formula, M.sub.L is preferably Ca, w is preferably 0.1 to 0.2, x+w is preferably 0.4 to 0.7, and y is preferably 0. The solid solution can be used in an electrochemical cell where it more closely matches the thermal expansion characteristics of the support tube and electrolyte of the cell.

  16. Solid oxide fuel cells, and air electrode and electrical interconnection materials therefor

    DOEpatents

    Bates, J.L.

    1992-09-01

    In one aspect of the invention, an air electrode material for a solid oxide fuel cell comprises Y[sub 1[minus]a]Q[sub a]MnO[sub 3], where Q is selected from the group consisting of Ca and Sr or mixtures thereof and a' is from 0.1 to 0.8. Preferably, a' is from 0.4 to 0.7. In another aspect of the invention, an electrical interconnection material for a solid oxide fuel cell comprises Y[sub 1[minus]b]Ca[sub b]Cr[sub 1[minus]c]Al[sub c]O[sub 3], where b' is from 0.1 to 0.6 and c' is from 0 to 9.3. Preferably, b' is from 0.3 to 0.5 and c' is from 0.05 to 0.1. A composite solid oxide electrochemical fuel cell incorporating these materials comprises: a solid oxide air electrode and an adjacent solid oxide electrical interconnection which commonly include the cation Y, the air electrode comprising Y[sub 1[minus]a]Q[sub a]MnO[sub 3], where Q is selected from the group consisting of Ca and Sr or mixtures thereof and a' is from 0.1 to 0.8, the electrical interconnection comprising Y[sub 1[minus]b]Ca[sub b]Cr[sub 1[minus]c]Al[sub c]O[sub 3], where b' is from 0.1 to 0.6 and c' is from 0.0 to 0.3; a yttrium stabilized solid electrolyte comprising (1[minus]d)ZrO[sub 2]-(d)Y[sub 2]O[sub 3] where d' is from 0.06 to 0.5; and a solid fuel electrode comprising X-ZrO[sub 2], where X' is an elemental metal. 5 figs.

  17. Solid oxide fuel cells, and air electrode and electrical interconnection materials therefor

    DOEpatents

    Bates, J. Lambert

    1992-01-01

    In one aspect of the invention, an air electrode material for a solid oxide fuel cell comprises Y.sub.1-a Q.sub.a MnO.sub.3, where "Q" is selected from the group consisting of Ca and Sr or mixtures thereof and "a" is from 0.1 to 0.8. Preferably, "a" is from 0.4 to 0.7. In another aspect of the invention, an electrical interconnection material for a solid oxide fuel cell comprises Y.sub.1-b Ca.sub.b Cr.sub.1-c Al.sub.c O.sub.3, where "b" is from 0.1 to 0.6 and "c" is from 0 to 9.3. Preferably, "b" is from 0.3 to 0.5 and "c" is from 0.05 to 0.1. A composite solid oxide electrochemical fuel cell incorporating these materials comprises: a solid oxide air electrode and an adjacent solid oxide electrical interconnection which commonly include the cation Y, the air electrode comprising Y.sub.1-a Q.sub.a MnO.sub.3, where "Q" is selected from the group consisting of Ca and Sr or mixtures thereof and "a" is from 0.1 to 0.8, the electrical interconnection comprising Y.sub.1-b Ca.sub.b Cr.sub.1-c Al.sub.c O.sub.3, where "b" is from 0.1 to 0.6 and "c" is from 0.0 to 0.3; a yttrium stabilized solid electrolyte comprising (1-d)ZrO.sub.2 -(d)Y.sub.2 O.sub.3 where "d" is from 0.06 to 0.5; and a solid fuel electrode comprising X-ZrO.sub.2, where "X" is an elemental metal.

  18. Graphene Oxide Involved Air-Controlled Electrospray for Uniform, Fast, Instantly Dry, and Binder-Free Electrode Fabrication.

    PubMed

    Fei, Ling; Yoo, Sang Ha; Villamayor, Rachel Ann R; Williams, Brian P; Gong, Seon Young; Park, Sunchan; Shin, Kyusoon; Joo, Yong Lak

    2017-03-22

    We report a facile air-controlled electrospray method to directly deposit binder-free active materials/graphene oxide (GO) onto current collectors. This method is inspired from an electrospinning process, and possesses all the advantages that electrospinning has such as low cost, easy scaling up, and simultaneous solvent evaporation during the spraying process. Moreover, the spray slurry is only a simple mixture of active materials and GO suspension in water, no binder polymer, organic solvent, and conductive carbon required. In our research, high-capacity Si nanoparticles (Si NP, 70-100 nm) and SiO microparticles (SiO MP, 3-10 μm) were selected to demonstrate the capability of this method to accommodate particles with different sizes. Their mixture with GO was sprayed onto a collector and then thermally annealed in an inert gas to obtain Si NP or SiO MP/reduced graphene oxide (RGO) binder-free electrodes. We are also able to directly deposit fairly large electrode sheets (e.g., 12 × 21 in.) upon the application requirement. To the best of our knowledge, this is the simplest approach to produce Si-related materials/RGO layered structures directly on current collector with controllable area and loading. Si and SiO MP/RGO are evaluated in both half and full lithium cells, showing good electrochemical performance. Prelithiation is also studied and gives a high first cycle Coulombic efficiency. In addition to Si-related materials, other materials with different shapes and sizes (e.g., MoO3 nanobelts, Sn/carbon nanofibers, and commercial sulfur particles) can also be sprayed. Beyond the preparation of battery electrodes, this approach can also be applied for other types of electrode preparation such as that of a supercapacitor, fuel cell, and solar cell.

  19. Investigation of Lithium-Air Battery Discharge Product Formed on Carbon Nanotube and Nanofiber Electrodes

    NASA Astrophysics Data System (ADS)

    Mitchell, Robert Revell, III

    Carbon nanotubes have been actively investigated for integration in a wide variety of applications since their discovery over 20 years ago. Their myriad desirable material properties including exceptional mechanical strength, high thermal conductivities, large surface-to-volume ratios, and considerable electrical conductivities, which are attributable to a quantum mechanical ability to conduct electrons ballistically, have continued to motivate interest in this material system. While a variety of synthesis techniques exist, carbon nanotubes and nanofibers are most often conveniently synthesized using chemical vapor deposition (CVD), which involves their catalyzed growth from transition metal nanoparticles. Vertically-aligned nanotube and nanofiber carpets produced using CVD have been utilized in a variety of applications including those related to energy storage. Li-air (Li-O2) batteries have received much interest recently because of their very high theoretical energy densities (3200 Wh/kgLi2O2 ). which make them ideal candidates for energy storage devices for future fully-electric vehicles. During operation of a Li-air battery O2 is reduced on the surface a porous air cathode, reacting with Li-ions to form lithium peroxide (Li-O2). Unlike the intercalation reactions of Li-ion batteries, discharge in a Li-air cell is analogous to an electrodeposition process involving the nucleation and growth of the depositing species on a foreign substrate. Carbon nanofiber electrodes were synthesized on porous substrates using a chemical vapor deposition process and then assembled into Li-O2 cells. The large surface to volume ratio and low density of carbon nanofiber electrodes were found to yield a very high gravimetric energy density in Li-O 2 cells, approaching 75% of the theoretical energy density for Li 2O2. Further, the carbon nanofiber electrodes were found to be excellent platforms for conducting ex situ electron microscopy investigations of the deposition Li2O2 phase

  20. Graphene-ferroelectric hybrid structure for flexible transparent electrodes.

    PubMed

    Ni, Guang-Xin; Zheng, Yi; Bae, Sukang; Tan, Chin Yaw; Kahya, Orhan; Wu, Jing; Hong, Byung Hee; Yao, Kui; Özyilmaz, Barbaros

    2012-05-22

    Graphene has exceptional optical, mechanical, and electrical properties, making it an emerging material for novel optoelectronics, photonics, and flexible transparent electrode applications. However, the relatively high sheet resistance of graphene is a major constraint for many of these applications. Here we propose a new approach to achieve low sheet resistance in large-scale CVD monolayer graphene using nonvolatile ferroelectric polymer gating. In this hybrid structure, large-scale graphene is heavily doped up to 3 × 10(13) cm(-2) by nonvolatile ferroelectric dipoles, yielding a low sheet resistance of 120 Ω/□ at ambient conditions. The graphene-ferroelectric transparent conductors (GFeTCs) exhibit more than 95% transmittance from the visible to the near-infrared range owing to the highly transparent nature of the ferroelectric polymer. Together with its excellent mechanical flexibility, chemical inertness, and the simple fabrication process of ferroelectric polymers, the proposed GFeTCs represent a new route toward large-scale graphene-based transparent electrodes and optoelectronics.

  1. Linear particle accelerator with seal structure between electrodes and insulators

    DOEpatents

    Broadhurst, John H.

    1989-01-01

    An electrostatic linear accelerator includes an electrode stack comprised of primary electrodes formed or Kovar and supported by annular glass insulators having the same thermal expansion rate as the electrodes. Each glass insulator is provided with a pair of fused-in Kovar ring inserts which are bonded to the electrodes. Each electrode is designed to define a concavo-convex particle trap so that secondary charged particles generated within the accelerated beam area cannot reach the inner surface of an insulator. Each insulator has a generated inner surface profile which is so configured that the electrical field at this surface contains no significant tangential component. A spark gap trigger assembly is provided, which energizes spark gaps protecting the electrodes affected by over voltage to prevent excessive energy dissipation in the electrode stack.

  2. A micromechanical model for effective conductivity in granular electrode structures

    NASA Astrophysics Data System (ADS)

    Ott, Julia; Völker, Benjamin; Gan, Yixiang; McMeeking, Robert M.; Kamlah, Marc

    2013-10-01

    Optimization of composition and microstructure is important to enhance performance of solid oxide fuel cells (SOFC) and lithium-ion batteries (LIB). For this, the porous electrode structures of both SOFC and LIB are modeled as a binary mixture of electronic and ionic conducting particles to estimate effective transport properties. Particle packings of 10 000 spherical, binary sized and randomly positioned particles are created numerically and densified considering the different manufacturing processes in SOFC and LIB: the sintering of SOFC electrodes is approximated geometrically, whereas the calendering process and volume change due to intercalation in LIB are modeled physically by a discrete element approach. A combination of a tracking algorithm and a resistor network approach is developed to predict the connectivity and effective conductivity for the various densified structures. For SOFC, a systematic study of the influence of morphology on connectivity and conductivity is performed on a large number of assemblies with different compositions and particle size ratios between 1 and 10. In comparison to percolation theory, an enlarged percolation area is found, especially for large size ratios. It is shown that in contrast to former studies the percolation threshold correlates to varying coordination numbers. The effective conductivity shows not only an increase with volume fraction as expected but also with size ratio. For LIB, a general increase of conductivity during the intercalation process was observed in correlation with increasing contact forces. The positive influence of calendering on the percolation threshold and the effective conductivity of carbon black is shown. The anisotropy caused by the calendering process does not influence the carbon black phase.

  3. Highly conductive transparent organic electrodes with multilayer structures for rigid and flexible optoelectronics.

    PubMed

    Guo, Xiaoyang; Liu, Xingyuan; Lin, Fengyuan; Li, Hailing; Fan, Yi; Zhang, Nan

    2015-05-27

    Transparent electrodes are essential components for optoelectronic devices, such as touch panels, organic light-emitting diodes, and solar cells. Indium tin oxide (ITO) is widely used as transparent electrode in optoelectronic devices. ITO has high transparency and low resistance but contains expensive rare elements, and ITO-based devices have poor mechanical flexibility. Therefore, alternative transparent electrodes with excellent opto-electrical performance and mechanical flexibility will be greatly demanded. Here, organics are introduced into dielectric-metal-dielectric structures to construct the transparent electrodes on rigid and flexible substrates. We show that organic-metal-organic (OMO) electrodes have excellent opto-electrical properties (sheet resistance of below 10 Ω sq(-1) at 85% transmission), mechanical flexibility, thermal and environmental stabilities. The OMO-based polymer photovoltaic cells show performance comparable to that of devices based on ITO electrodes. This OMO multilayer structure can therefore be used to produce transparent electrodes suitable for use in a wide range of optoelectronic devices.

  4. A Metal-Free, Free-Standing, Macroporous Graphene@g-C₃N₄ Composite Air Electrode for High-Energy Lithium Oxygen Batteries.

    PubMed

    Luo, Wen-Bin; Chou, Shu-Lei; Wang, Jia-Zhao; Zhai, Yu-Chun; Liu, Hua-Kun

    2015-06-01

    The nonaqueous lithium oxygen battery is a promising candidate as a next-generation energy storage system because of its potentially high energy density (up to 2-3 kW kg(-1)), exceeding that of any other existing energy storage system for storing sustainable and clean energy to reduce greenhouse gas emissions and the consumption of nonrenewable fossil fuels. To achieve high energy density, long cycling stability, and low cost, the air electrode structure and the electrocatalysts play important roles. Here, a metal-free, free-standing macroporous graphene@graphitic carbon nitride (g-C3N4) composite air cathode is first reported, in which the g-C3N4 nanosheets can act as efficient electrocatalysts, and the macroporous graphene nanosheets can provide space for Li2O2 to deposit and also promote the electron transfer. The electrochemical results on the graphene@g-C3N4 composite air electrode show a 0.48 V lower charging plateau and a 0.13 V higher discharging plateau than those of pure graphene air electrode, with a discharge capacity of nearly 17300 mA h g(-1)(composite) . Excellent cycling performance, with terminal voltage higher than 2.4 V after 105 cycles at 1000 mA h g(-1)(composite) capacity, can also be achieved. Therefore, this hybrid material is a promising candidate for use as a high energy, long-cycle-life, and low-cost cathode material for lithium oxygen batteries.

  5. Air Damping in a Fan-Shaped Rotational Resonator with Comb Electrodes

    NASA Astrophysics Data System (ADS)

    Uchida, Yuki; Sugano, Koji; Tsuchiya, Toshiyuki; Tabata, Osamu; Ikehara, Tsuyoshi

    We theoretically and experimentally evaluated the damping effect in a rotational resonator with a comb-drive actuator and sensor. The resonator was fabricated from an SOI wafer and has a fan-shaped mass. The underlying substrate was removed using back side deep reactive ion etching. One set of comb electrodes was attached to each side of the mass: one for electrostatic driving and the other for capacitive detection. In our theoretical analysis, the dynamics of the resonator were simplified so that they could be represented by a lumped system. In this lumped system, the damping coefficient was estimated by assuming the damping to be slide film damping and the air flow to be a Stokes flow. The phase shift due to the slide film damping of thick air layers was included in the lumped system. In the experimental evaluation, one side of the rotational combs was removed step-by-step and a half of the mass using a laser trimming tool so that the individual damping effects caused by the comb electrodes and mass could be determined quantitatively. We compared the experimental results with the results of the theoretical analysis and found that the difference in the damping coefficients between the experimental results and results of the theoretical analysis was less than 40%.

  6. Zinc/air battery R and D research and development of bifunctional oxygen electrode: Tasks I and II, Final report

    SciTech Connect

    Klein, M.; Viswanathan, S.

    1986-12-01

    Studies were conducted of the bifunctional oxygen electrode. The development of a rechargeable metal-oxygen (air) cell has been hampered to a great extent by the lack of a stable and cost effective oxygen electrode capable of use during both charge and discharge. The first type of bifunctional electrode consists of two distinct catalytifc layers. The oxygen reduction catalyst layer containing a supported gold catalyst is in contact with a hydrophilic nickel layer in which evolution of oxygen takes place. Loadings of gold from 0.5 to 1.0 mg/cm/sup 2/ were investigated; carbon, graphite, metal, and spinel oxides were evaluated as substrates. The second part of the research effort was centered on developing a reversible oxygen electrode containing only one catalytic layer for both reduction and evolution of oxygen. The work was directed specifically to the study of perovskite type of oxides with the composition AA/sup 1/BO/sub 3/ where A is an element of the lanthanide series, A/sup 1/ is an alkaline earth metal and B, a first row transition element. Initial polarization data obtained in unscrubbed air gave a value of approximately 200 millivolts vs Hg/HgO reference electrode at a current density of 50 ma/cm/sup 2/. Electrodes were made both by roll-bonding and by pelletizing techniques and tested for polarization and cycle life. This study also indicates the optimum process conditions for the manufacture of oxides and fabrication of electrodes.

  7. Hydrogen peroxide detection in wet air with a Prussian Blue based solid salt bridged three electrode system.

    PubMed

    Komkova, Maria A; Karyakina, Elena E; Marken, Frank; Karyakin, Arkady A

    2013-03-05

    We report on a novel electroanalytical system for hydrogen peroxide (H2O2) detection in humidity or droplets of aerosol, formed by air bubbling through a washing chamber; the resulting flow mimics the exhaled human breath. The system is based on a planar three-electrode structure (with a Prussian Blue based H2O2 transducer modified working electrode) bridged by a solid salt-saturated filament material (filter paper, cotton textile). Respective to the hydrogen peroxide content in the washing valve, the response of the aerosol-sensing system is linear in the concentration range of 0.1-10 μM, which overlaps the generally accepted H2O2 content in exhaled breath condensate (EBC), with the sensitivity of 8 A M(-1) cm(-2). The response to the upper limit of the calibration range is stable for more than 50 injection cycles recorded within 3 days. Both the stability and the suitable calibration range allow one to consider the reported aerosol-sensing system as a prototype for a simple (avoiding intermediate EBC collection) noninvasive diagnostic tool for pulmonary patients.

  8. Influence of Structure and Surface Chemistry of Porous Carbon Electrodes on Supercapacitor Performance

    NASA Astrophysics Data System (ADS)

    Dyatkin, Boris

    Electrochemical double layer capacitors, which rely on electrosorption of ions in nanostructured carbon electrodes, can supplement or even replace traditional batteries in energy harvesting and storage applications. While supercapacitors offer > 10 kW/kg power densities, their ~5 Wh/kg energy densities are insufficient for many automotive and grid storage applications. Most prior efforts have focused on novel high-performing ionic liquid electrolytes and porous carbons with tunable pore diameters and high specific surface areas. However, existing research lacks fundamental understanding of the influence of surface heterogeneity and disorder, such as graphitic defects and functional groups, on key electrosorption properties at electrode-electrolyte interfaces. These interactions significantly impact charge accumulation densities, ion transport mechanisms, and electrolyte breakdown processes. Subsequently, they must be investigated to optimize ion screening, charge mobilities, and operating voltage windows of the devices. The research in this dissertation examined the influence of surface functional groups and structural ordering on capacitance, electrosorption dynamics, and electrochemical stability of external and internal surface of carbon electrodes. High-temperature vacuum annealing, air oxidation, hydrogenation, and amination were used to tune pore surface compositions and decouple key structural and chemical properties of carbide-derived carbons. The approach combined materials characterization by a variety of techniques, neutron scattering studies of ion dynamics, electrochemical testing, and MD simulations to investigate the fundamental intermolecular interactions and dynamics of ions electrosorption in different pore architectures and on planar graphene surfaces. Contrary to expected results and existing theories, defect removal via defunctionalization and graphitization decreased capacitance. Hydrogenated surfaces benefitted electrosorption, while oxygen

  9. Nanostructured gold and platinum electrodes on silicon structures for biosensing

    NASA Astrophysics Data System (ADS)

    Ogurtsov, V. I.; Sheehan, M. M.

    2005-01-01

    Gold and platinum metal electrodes on Si/SiO2 having undergone anisotropic potassium hydroxide (KOH) etch treatment are considered. This treatment etches at different rates and directions in the material resulting in creation of numerous pyramid shaped holes in the silicon substrate. This surface is used to make metal electrodes with increased electrode efficiency. The electrodes can serve as the sensors or as the sensor substrates (for surface polymer modification) and because both gold and platinum are inert they have applications for food safety biosensing. Wine, an economically significant food product, was chosen as a matrix, and impedance spectroscopy (EIS) was selected as a method of investigation of electrode behaviour. Based on results of EIS, different complexity equivalent circuits were determined by applying fitting mean square root optimisation of sensor complex impedance measurements.

  10. Glow Discharge Emission Spectra in Air with Liquid Electrode Based on Distilled Water

    NASA Astrophysics Data System (ADS)

    Chuchman, M. P.; Mesarosz, L. V.; Shuaibov, A. K.; Kiris, V. V.; Tarasenko, N. V.

    2016-11-01

    The results of spectroscopic studies of a glow discharge plasma at atmospheric pressure in air with an electrode based on distilled water are presented. The parametric effects affecting the discharge emission are analyzed. The dependence of the emission intensity of the various discharge components and their spatial localization in the discharge gap on the current strength is explained by change in the discharge geometry and the conditions of oxidation with increase of the current. It is shown that the composition of the gas mixture in the electrode gap changes with increase of the discharge current from nitrogen-rich (12-19 mA) to rich in water vapor and its dissociation products (19-24 mA). At higher currents, the gas mixture is also rich in the products of plasma chemical reactions and nitric oxide in particular. The redistribution of the radiation intensity of the molecules of nitrogen and its oxide with increase of the current occurs mainly in the cathode region (at the plasma-fluid boundary), where the formation of oxides is improved as a result of increase in the amount of vaporized solution and in the effectiveness of oxidation reactions with increase of the water temperature and discharge current.

  11. Magnetically Diffused Radial Electric-Arc Air Heater Employing Water-Cooled Copper Electrodes

    NASA Technical Reports Server (NTRS)

    Mayo, R. F.; Davis, D. D., Jr.

    1962-01-01

    A magnetically rotated electric-arc air heater has been developed that is novel in that an intense magnetic field of the order of 10,000 to 25,000 gauss is employed. This field is supplied by a coil that is connected in series with the arc. Experimentation with this heater has shown that the presence of an intense magnetic field transverse to the arc results in diffusion of the arc and that the arc has a positive effective resistance. With the field coil in series with the arc, highly stable arc operation is obtained from a battery power supply. External ballast is not required to stabilize the arc when it is operating at maximum power level. The electrode erosion rate is so low that the airstream contamination is no more than 0.07 percent and may be substantially less.

  12. Method of preparing electrodes with porous current collector structures and solid reactants for secondary electrochemical cells

    DOEpatents

    Gay, Eddie C.; Martino, Fredric J.

    1976-01-01

    Particulate electrode reactants, for instance transition metal sulfides for the positive electrodes and lithium alloys for the negative electrodes, are vibratorily compacted into porous, electrically conductive structures. Structures of high porosity support sufficient reactant material to provide high cell capacity per unit weight while serving as an electrical current collector to improve the utilization of reactant materials. Pore sizes of the structure and particle sizes of the reactant material are selected to permit uniform vibratory loading of the substrate without settling of the reactant material during cycling.

  13. Ion flow and sheath structure near positively biased electrodes

    NASA Astrophysics Data System (ADS)

    Hood, Ryan; Scheiner, Brett; Baalrud, Scott; Hopkins, Matthew; Barnat, Ed; Yee, Benjamin; Merlino, Robert; Skiff, Fred

    2016-10-01

    Measurements of the ion velocity distribution function (IVDF) and plasma potential were made near small positively biased electrodes using laser-induced fluorescence (LIF) and an emissive probe. The effect of dielectric around the electrode was tested and compared with a 2D particle-in-cell (PIC) simulation. Both measurements and simulation reveal that if the electrode is embedded within a surrounding dielectric, ions are accelerated toward the electrode to approximately 0.5 times the ion sound speed before being deflected radially by the electron sheath potential barrier. The axial potential profile in this case contains a virtual cathode. In comparison, when the surrounding dielectric is removed, both the ion flow and virtual cathode depth are dramatically reduced. These measurements suggest that the ion presheath from the dielectric may enclose the electron sheath of the electrode resulting in a virtual cathode that substantially influences the local ion flow profile. This research was supported by the Office of Fusion Energy Sciences at the U.S. Department of Energy under contract DE-AC04-94SL85000.

  14. Electrochemical properties of lithium air batteries with Pt100-xRux (0 ≤ x ≤ 100) electrocatalysts for air electrodes

    NASA Astrophysics Data System (ADS)

    Yui, Yuhki; Sakamoto, Shuhei; Nohara, Masaya; Hayashi, Masahiko; Nakamura, Jiro; Komatsu, Takeshi

    2017-02-01

    Electrochemical properties of lithium air secondary battery cells with Pt100-xRux (0 ≤ x ≤ 100) electrocatalysts, prepared by the formic acid reduction method and loaded into air electrodes were examined in 1 mol/l LiTFSA/TEGDME electrolyte solution. Among the cells, the one with the Pt10Ru90 (x = 90)/carbon sample showed the largest discharge capacity of 1014 mAh/g and the lowest average charge voltage of 3.74 V. In addition, the x = 90 sample showed comparatively good cycle stability with discharge capacity of over 800 mAh/g at the 8th cycle. As a result, x = 90 was confirmed to be the optimized composition as the electrocatalyst for the air electrode.

  15. Interaction Between Air Propellers and Airplane Structures

    NASA Technical Reports Server (NTRS)

    Durand, W F

    1927-01-01

    The purpose of this investigation was the determination of the character and amount of interaction between air propellers as usually mounted on airplanes and the adjacent parts of the airplane structure - or, more specifically, those parts of the airplane structure within the wash of the propeller, and capable of producing any significant effect on propeller performance. In report no. 177 such interaction between air propellers and certain simple geometrical forms was made the subject of investigation and report. The present investigation aims to carry this general study one stage further by substituting actual airplane structures for the simple geometrical forms. From the point of view of the present investigation, the airplane structures, viewed as an obstruction in the wake of the propeller, must also be viewed as a necessary part of the airplane and not as an appendage which might be installed or removed at will. (author)

  16. Air Structures in Education. A Conference

    ERIC Educational Resources Information Center

    Price, Cedric

    1973-01-01

    Conference papers presented by leading architects, engineers, and educators concerning the latest developments in air structures, particularly as related to education. BRI-EFL national technical conference. (Columbia, Maryland, May 22-24, 1973.) Discussions center on educational opportunities, economics, technological developments, and the…

  17. 47 CFR 22.365 - Antenna structures; air navigation safety.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 47 Telecommunication 2 2014-10-01 2014-10-01 false Antenna structures; air navigation safety. 22... Antenna structures; air navigation safety. Licensees that own their antenna structures must not allow these antenna structures to become a hazard to air navigation. In general, antenna structure owners...

  18. 47 CFR 22.365 - Antenna structures; air navigation safety.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 2 2011-10-01 2011-10-01 false Antenna structures; air navigation safety. 22... Antenna structures; air navigation safety. Licensees that own their antenna structures must not allow these antenna structures to become a hazard to air navigation. In general, antenna structure owners...

  19. 47 CFR 22.365 - Antenna structures; air navigation safety.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Antenna structures; air navigation safety. 22... Antenna structures; air navigation safety. Licensees that own their antenna structures must not allow these antenna structures to become a hazard to air navigation. In general, antenna structure owners...

  20. 47 CFR 22.365 - Antenna structures; air navigation safety.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 47 Telecommunication 2 2013-10-01 2013-10-01 false Antenna structures; air navigation safety. 22... Antenna structures; air navigation safety. Licensees that own their antenna structures must not allow these antenna structures to become a hazard to air navigation. In general, antenna structure owners...

  1. 47 CFR 22.365 - Antenna structures; air navigation safety.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 2 2012-10-01 2012-10-01 false Antenna structures; air navigation safety. 22... Antenna structures; air navigation safety. Licensees that own their antenna structures must not allow these antenna structures to become a hazard to air navigation. In general, antenna structure owners...

  2. Characterization of interdigitated electrode structures for water contaminant detection using a hybrid voltage divider and a vector network analyzer.

    PubMed

    Rodríguez-Delgado, José Manuel; Rodríguez-Delgado, Melissa Marlene; Mendoza-Buenrostro, Christian; Dieck-Assad, Graciano; Omar Martínez-Chapa, Sergio

    2012-01-01

    Interdigitated capacitive electrode structures have been used to monitor or actuate over organic and electrochemical media in efforts to characterize biochemical properties. This article describes a method to perform a pre-characterization of interdigitated electrode structures using two methods: a hybrid voltage divider (HVD) and a vector network analyzer (VNA). Both methodologies develop some tests under two different conditions: free air and bi-distilled water media. Also, the HVD methodology is used for other two conditions: phosphate buffer with laccase (polyphenoloxidase; EC 1.10.3.2) and contaminated media composed by a mix of phosphate buffer and 3-ethylbenzothiazoline-6-sulfonic acid (ABTS). The purpose of this study is to develop and validate a characterization methodology using both, a hybrid voltage divider and VNA T-# network impedance models of the interdigitated capacitive electrode structure that will provide a shunt RC network of particular interest in detecting the amount of contamination existing in the water solution for the media conditions. This methodology should provide us with the best possible sensitivity in monitoring water contaminant media characteristics. The results show that both methods, the hybrid voltage divider and the VNA methodology, are feasible in determining impedance modeling parameters. These parameters can be used to develop electric interrogation procedures and devices such as dielectric characteristics to identify contaminant substances in water solutions.

  3. Particle trapping and impedance measurement using bilayer electrodes integrated with microcavity structure

    NASA Astrophysics Data System (ADS)

    Chen, Guan-Ting; Liu, Chia-Feng; Jang, Ling-Sheng; Li, Shun-Lai; Wang, Min-Haw

    2017-03-01

    Traditional planar electrodes for single-particle impedance measurement have difficulty in trapping and positioning particles. This paper proposes a microfluidic device for single-particle trapping and impedance measurement with a microcavity configuration. A carbon dioxide (CO2) laser technique was used to fabricate the microcavity structure, which can capture 15 µm diameter particles without requiring additional trapping structures. The measurement electrodes on both sides of the microcavity were fabricated using electroplating and deposition techniques. The advantages of the microcavity structure and electrodes are discussed. The bottom electrode spreads into the microcavity to increase measurement sensitivity and shrink the exit aperture to around 10 µm for particle trapping. The experimental results show that the device successfully captured particles and distinguished the impedance of a particle from that of phosphate-buffered saline solution.

  4. Fabrication of fuel cell electrodes and other catalytic structures

    DOEpatents

    Smith, J.L.

    1987-02-11

    A porous layer of catalyst material suitable for use as an electrode in a molten carbonate fuel cell includes elongated pores substantially extending across the layer thickness. The catalyst layer is prepared by depositing particulate catalyst material into polymeric flocking on a substrate surface by a procedure such as tape casting. The loaded substrate is heated in a series of steps with rising temperatures to set the tape, thermally decompose the substrate with flocking and sinter bond the catalyst particles into a porous catalytic layer with elongated pores across its thickness. Employed as an electrode, the elongated pores provide distribution of reactant gas into contact with catalyst particles wetted by molten electrolyte. 1 fig.

  5. Method of fabricating conductive electrodes on the front and backside of a thin film structure

    DOEpatents

    Tabada, Phillipe J.; Tabada, legal representative, Melody; Pannu, Satinderpall S.

    2011-05-22

    A method of fabricating a thin film device having conductive front and backside electrodes or contacts. Top-side cavities are first formed on a first dielectric layer, followed by the deposition of a metal layer on the first dielectric layer to fill the cavities. Defined metal structures are etched from the metal layer to include the cavity-filled metal, followed by depositing a second dielectric layer over the metal structures. Additional levels of defined metal structures may be formed in a similar manner with vias connecting metal structures between levels. After a final dielectric layer is deposited, a top surface of a metal structure of an uppermost metal layer is exposed through the final dielectric layer to form a front-side electrode, and a bottom surface of a cavity-filled portion of a metal structure of a lowermost metal layer is also exposed through the first dielectric layer to form a back-side electrode.

  6. Study on electrical characteristics of barrier-free atmospheric air diffuse discharge generated by nanosecond pulses and long wire electrodes

    SciTech Connect

    Li, Lee Liu, Yun-Long; Teng, Yun; Liu, Lun; Pan, Yuan

    2014-07-15

    In room-temperature atmospheric air, the large-scale diffuse plasmas can be generated via high-voltage nanosecond pulses with short rise-time and wire electrodes. Diffuse discharge with the wire electrode length up to 110.0 cm and the discharge spacing of several centimeters has been investigated in this paper. Electrical characteristics of diffuse discharge have been analyzed by their optical photographs and measuring of the voltage and current waveforms. Experimental results show the electrode spacing, and the length of wire electrodes can influence the intensity and mode transition of diffuse discharge. The characteristic of current waveforms is that there are several current oscillation peaks at the time of applied pulsed voltage peak, and at the tail of applied pulse, the conduction current component will compensate the displacement one so that the measured current is unidirectional in diffuse discharge mode. The transition from diffuse discharge to arc discharge is always with the increasing of conduction current density. As for nanosecond pulses with long tail, the long wire electrodes are help for generating non-equilibrium diffuse plasmas.

  7. Highly Conductive Transparent Organic Electrodes with Multilayer Structures for Rigid and Flexible Optoelectronics

    PubMed Central

    Guo, Xiaoyang; Liu, Xingyuan; Lin, Fengyuan; Li, Hailing; Fan, Yi; Zhang, Nan

    2015-01-01

    Transparent electrodes are essential components for optoelectronic devices, such as touch panels, organic light-emitting diodes, and solar cells. Indium tin oxide (ITO) is widely used as transparent electrode in optoelectronic devices. ITO has high transparency and low resistance but contains expensive rare elements, and ITO-based devices have poor mechanical flexibility. Therefore, alternative transparent electrodes with excellent opto-electrical performance and mechanical flexibility will be greatly demanded. Here, organics are introduced into dielectric–metal–dielectric structures to construct the transparent electrodes on rigid and flexible substrates. We show that organic-metal-organic (OMO) electrodes have excellent opto-electrical properties (sheet resistance of below 10 Ω sq−1 at 85% transmission), mechanical flexibility, thermal and environmental stabilities. The OMO-based polymer photovoltaic cells show performance comparable to that of devices based on ITO electrodes. This OMO multilayer structure can therefore be used to produce transparent electrodes suitable for use in a wide range of optoelectronic devices. PMID:26014889

  8. Employment of a metal microgrid as a front electrode in a sandwich-structured photodetector.

    PubMed

    Zhang, Junying; Cai, Chao; Pan, Feng; Hao, Weichang; Zhang, Weiwei; Wang, Tianmin

    2009-07-01

    A highly UV-transparent metal microgrid was prepared and employed as the front electrode in a sandwich-structured ultraviolet (UV) photodetector using TiO(2) thin film as the semiconductor layer. The photo-generated charger carriers travel a shorter distance before reaching the electrodes in comparison with a photodetector using large-spaced interdigitated metal electrodes (where distance between fingers is several to tens of micrometers) on the surface of the semiconductor film. This photodetector responds to UV light irradiation, and the photocurrent intensity increases linearly with the irradiation intensity below 0.2 mW/cm(2).

  9. Membrane-electrode structures for molecular catalysts for use in fuel cells and other electrochemical devices

    DOEpatents

    Kerr, John B.; Zhu, Xiaobing; Hwang, Gi Suk; Martin, Zulima; He, Qinggang; Driscoll, Peter; Weber, Adam; Clark, Kyle

    2016-09-27

    Water soluble catalysts, (M)meso-tetra(N-Methyl-4-Pyridyl)Porphinepentachloride (M=Fe, Co, Mn & Cu), have been incorporated into the polymer binder of oxygen reduction cathodes in membrane electrode assemblies used in PEM fuel cells and found to support encouragingly high current densities. The voltages achieved are low compared to commercial platinum catalysts but entirely consistent with the behavior observed in electroanalytical measurements of the homogeneous catalysts. A model of the dynamics of the electrode action has been developed and validated and this allows the MEA electrodes to be optimized for any chemistry that has been demonstrated in solution. It has been shown that improvements to the performance will come from modifications to the structure of the catalyst combined with optimization of the electrode structure and a well-founded pathway to practical non-platinum group metal catalysts exists.

  10. Ordered macroporous platinum electrode and enhanced mass transfer in fuel cells using inverse opal structure.

    PubMed

    Kim, Ok-Hee; Cho, Yong-Hun; Kang, Soon Hyung; Park, Hee-Young; Kim, Minhyoung; Lim, Ju Wan; Chung, Dong Young; Lee, Myeong Jae; Choe, Heeman; Sung, Yung-Eun

    2013-01-01

    Three-dimensional, ordered macroporous materials such as inverse opal structures are attractive materials for various applications in electrochemical devices because of the benefits derived from their periodic structures: relatively large surface areas, large voidage, low tortuosity and interconnected macropores. However, a direct application of an inverse opal structure in membrane electrode assemblies has been considered impractical because of the limitations in fabrication routes including an unsuitable substrate. Here we report the demonstration of a single cell that maintains an inverse opal structure entirely within a membrane electrode assembly. Compared with the conventional catalyst slurry, an ink-based assembly, this modified assembly has a robust and integrated configuration of catalyst layers; therefore, the loss of catalyst particles can be minimized. Furthermore, the inverse-opal-structure electrode maintains an effective porosity, an enhanced performance, as well as an improved mass transfer and more effective water management, owing to its morphological advantages.

  11. 47 CFR 27.56 - Antenna structures; air navigation safety.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 47 Telecommunication 2 2013-10-01 2013-10-01 false Antenna structures; air navigation safety. 27... SERVICES MISCELLANEOUS WIRELESS COMMUNICATIONS SERVICES Technical Standards § 27.56 Antenna structures; air navigation safety. A licensee that owns its antenna structure(s) must not allow such antenna structure(s)...

  12. 47 CFR 27.56 - Antenna structures; air navigation safety.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 47 Telecommunication 2 2014-10-01 2014-10-01 false Antenna structures; air navigation safety. 27... SERVICES MISCELLANEOUS WIRELESS COMMUNICATIONS SERVICES Technical Standards § 27.56 Antenna structures; air navigation safety. A licensee that owns its antenna structure(s) must not allow such antenna structure(s)...

  13. 47 CFR 27.56 - Antenna structures; air navigation safety.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Antenna structures; air navigation safety. 27... SERVICES MISCELLANEOUS WIRELESS COMMUNICATIONS SERVICES Technical Standards § 27.56 Antenna structures; air navigation safety. A licensee that owns its antenna structure(s) must not allow such antenna structure(s)...

  14. 47 CFR 27.56 - Antenna structures; air navigation safety.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 2 2012-10-01 2012-10-01 false Antenna structures; air navigation safety. 27... SERVICES MISCELLANEOUS WIRELESS COMMUNICATIONS SERVICES Technical Standards § 27.56 Antenna structures; air navigation safety. A licensee that owns its antenna structure(s) must not allow such antenna structure(s)...

  15. 47 CFR 27.56 - Antenna structures; air navigation safety.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 2 2011-10-01 2011-10-01 false Antenna structures; air navigation safety. 27... SERVICES MISCELLANEOUS WIRELESS COMMUNICATIONS SERVICES Technical Standards § 27.56 Antenna structures; air navigation safety. A licensee that owns its antenna structure(s) must not allow such antenna structure(s)...

  16. Rechargeable Lithium-Air Batteries: Development of Ultra High Specific Energy Rechargeable Lithium-Air Batteries Based on Protected Lithium Metal Electrodes

    SciTech Connect

    2010-07-01

    BEEST Project: PolyPlus is developing the world’s first commercially available rechargeable lithium-air (Li-Air) battery. Li-Air batteries are better than the Li-Ion batteries used in most EVs today because they breathe in air from the atmosphere for use as an active material in the battery, which greatly decreases its weight. Li-Air batteries also store nearly 700% as much energy as traditional Li-Ion batteries. A lighter battery would improve the range of EVs dramatically. Polyplus is on track to making a critical breakthrough: the first manufacturable protective membrane between its lithium–based negative electrode and the reaction chamber where it reacts with oxygen from the air. This gives the battery the unique ability to recharge by moving lithium in and out of the battery’s reaction chamber for storage until the battery needs to discharge once again. Until now, engineers had been unable to create the complex packaging and air-breathing components required to turn Li-Air batteries into rechargeable systems.

  17. Ramp-edge structured tunneling devices using ferromagnet electrodes

    DOEpatents

    Kwon, Chuhee; Jia, Quanxi

    2002-09-03

    The fabrication of ferromagnet-insulator-ferromagnet magnetic tunneling junction devices using a ramp-edge geometry based on, e.g., (La.sub.0.7 Sr.sub.0.3) MnO.sub.3, ferromagnetic electrodes and a SrTiO.sub.3 insulator is disclosed. The maximum junction magnetoresistance (JMR) as large as 23% was observed below 300 Oe at low temperatures (T<100 K). These ramp-edge junctions exhibited JMR of 6% at 200 K with a field less than 100 Oe.

  18. In situ hydrodynamic spectroscopy for structure characterization of porous energy storage electrodes

    NASA Astrophysics Data System (ADS)

    Shpigel, Netanel; Levi, Mikhael D.; Sigalov, Sergey; Girshevitz, Olga; Aurbach, Doron; Daikhin, Leonid; Pikma, Piret; Marandi, Margus; Jänes, Alar; Lust, Enn; Jäckel, Nicolas; Presser, Volker

    2016-05-01

    A primary atomic-scale effect accompanying Li-ion insertion into rechargeable battery electrodes is a significant intercalation-induced change of the unit cell volume of the crystalline material. This generates a variety of secondary multiscale dimensional changes and causes a deterioration in the energy storage performance stability. Although traditional in situ height-sensing techniques (atomic force microscopy or electrochemical dilatometry) are able to sense electrode thickness changes at a nanometre scale, they are much less informative concerning intercalation-induced changes of the porous electrode structure at a mesoscopic scale. Based on a electrochemical quartz-crystal microbalance with dissipation monitoring on multiple overtone orders, herein we introduce an in situ hydrodynamic spectroscopic method for porous electrode structure characterization. This new method will enable future developments and applications in the fields of battery and supercapacitor research, especially for diagnostics of viscoelastic properties of binders for composite electrodes and probing the micromechanical stability of their internal electrode porous structure and interfaces.

  19. Air Structures. Educational Facilities Review Series Number 23.

    ERIC Educational Resources Information Center

    Finne, Mary Lou

    Air structures can be erected quickly, cover large areas, cost substantially less than conventional buildings, and use less natural resources. Air structures are economically utilized for many facilities, such as athletic fields, swimming pools, high schools, day care centers, and college campuses. The literature on air structures covered in this…

  20. Advanced Metallic Air Vehicle Structure Program

    DTIC Science & Technology

    1976-08-01

    Patterson Air Force Base , Ohio 45433. AIR FORCE FLIGHT DYNAMICS LABORATORY AIR FORCE WRIGHT AERONAUTICAL LABORATORIES AIR FORCE SYSTEMS COMMAND Best...Available Copy WRIGHT-PATTERSON AIR FORCE BASE , OHIO 45433 THIS DOCUMENT CONTAINED C) BLANK PAGES THAT HAVE 0 3 BEEN DELETED 9 NOTICES When Government...December 1975. Other requests for this document must be referred to Air Force Flight Dynamics Laboratory (FB-A), Wright-Patterson Air Force Base , Ohio

  1. Doped lanthanum nickelates with a layered perovskite structure as bifunctional cathode catalysts for rechargeable metal-air batteries.

    PubMed

    Jung, Kyu-Nam; Jung, Jong-Hyuk; Im, Won Bin; Yoon, Sukeun; Shin, Kyung-Hee; Lee, Jong-Won

    2013-10-23

    Rechargeable metal-air batteries have attracted a great interest in recent years because of their high energy density. The critical challenges facing these technologies include the sluggish kinetics of the oxygen reduction-evolution reactions on a cathode (air electrode). Here, we report doped lanthanum nickelates (La2NiO4) with a layered perovskite structure that serve as efficient bifunctional electrocatalysts for oxygen reduction and evolution in an aqueous alkaline electrolyte. Rechargeable lithium-air and zinc-air batteries assembled with these catalysts exhibit remarkably reduced discharge-charge voltage gaps (improved round-trip efficiency) as well as high stability during cycling.

  2. Tuning of structural color using a dielectric actuator and multifunctional compliant electrodes.

    PubMed

    Fang, Zhao H; Punckt, Christian; Leung, Eva Y; Schniepp, Hannes C; Aksay, Ilhan A

    2010-12-10

    We have developed electrically conducting silicone elastomer nanocomposites that serve both as compliant electrodes in an electrostatic actuator and, at the same time, as optically active elements creating structural color. We demonstrate the capabilities of our setup by actuating an elastomeric diffraction grating and colloidal-crystal-based photonic structures.

  3. Time-lag properties of corona streamer discharges between impulse sphere and dc needle electrodes under atmospheric air conditions.

    PubMed

    Okano, Daisuke

    2013-02-01

    In this study of corona streamer discharges from an impulse generator using a dc power supply, the relationship of the discharge time-lag with the dc bias voltage between the sphere-to-needle electrodes under atmospheric conditions is investigated. Devices utilizing corona discharges have been used to purify air or water, destroy bacteria, and to remove undesirable substances, and in order to achieve fast response times and high power efficiencies in such devices, it is important to minimize the time-lag of the corona discharge. Our experimental results show that (a) the discharge path of a negatively biased needle electrode will be straighter than that of a positively biased needle and (b) the discharge threshold voltage in both the positive and the negative needle electrodes is nearly equal to 33 kV. By expressing the discharge voltage as a power function of time-lag, the extent of corona generation can be quantitatively specified using the exponent of this power function. The observed behavior of a corona streamer discharge between the negative spherical and the positive needle electrodes indicates that the largest power exponent is associated with the shortest time-lag, owing to the reduction in the statistical time-lag in the absence of a formative time-lag.

  4. Time-lag properties of corona streamer discharges between impulse sphere and dc needle electrodes under atmospheric air conditions

    NASA Astrophysics Data System (ADS)

    Okano, Daisuke

    2013-02-01

    In this study of corona streamer discharges from an impulse generator using a dc power supply, the relationship of the discharge time-lag with the dc bias voltage between the sphere-to-needle electrodes under atmospheric conditions is investigated. Devices utilizing corona discharges have been used to purify air or water, destroy bacteria, and to remove undesirable substances, and in order to achieve fast response times and high power efficiencies in such devices, it is important to minimize the time-lag of the corona discharge. Our experimental results show that (a) the discharge path of a negatively biased needle electrode will be straighter than that of a positively biased needle and (b) the discharge threshold voltage in both the positive and the negative needle electrodes is nearly equal to 33 kV. By expressing the discharge voltage as a power function of time-lag, the extent of corona generation can be quantitatively specified using the exponent of this power function. The observed behavior of a corona streamer discharge between the negative spherical and the positive needle electrodes indicates that the largest power exponent is associated with the shortest time-lag, owing to the reduction in the statistical time-lag in the absence of a formative time-lag.

  5. Nano-honeycomb structured transparent electrode for enhanced light extraction from organic light-emitting diodes

    SciTech Connect

    Shi, Xiao-Bo; Qian, Min; Wang, Zhao-Kui E-mail: lsliao@suda.edu.cn; Liao, Liang-Sheng E-mail: lsliao@suda.edu.cn

    2015-06-01

    A universal nano-sphere lithography method has been developed to fabricate nano-structured transparent electrode, such as indium tin oxide (ITO), for light extraction from organic light-emitting diodes (OLEDs). Perforated SiO{sub 2} film made from a monolayer colloidal crystal of polystyrene spheres and tetraethyl orthosilicate sol-gel is used as a template. Ordered nano-honeycomb pits on the ITO electrode surface are obtained by chemical etching. The proposed method can be utilized to form large-area nano-structured ITO electrode. More than two folds' enhancement in both current efficiency and power efficiency has been achieved in a red phosphorescent OLED which was fabricated on the nano-structured ITO substrate.

  6. Method to planarize three-dimensional structures to enable conformal electrodes

    DOEpatents

    Nikolic, Rebecca J; Conway, Adam M; Graff, Robert T; Reinhardt, Catherine; Voss, Lars F; Shao, Qinghui

    2012-11-20

    Methods for fabricating three-dimensional PIN structures having conformal electrodes are provided, as well as the structures themselves. The structures include a first layer and an array of pillars with cavity regions between the pillars. A first end of each pillar is in contact with the first layer. A segment is formed on the second end of each pillar. The cavity regions are filled with a fill material, which may be a functional material such as a neutron sensitive material. The fill material covers each segment. A portion of the fill material is etched back to produce an exposed portion of the segment. A first electrode is deposited onto the fill material and each exposed segment, thereby forming a conductive layer that provides a common contact to each the exposed segment. A second electrode is deposited onto the first layer.

  7. 47 CFR 24.55 - Antenna structures; air navigation safety.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 47 Telecommunication 2 2014-10-01 2014-10-01 false Antenna structures; air navigation safety. 24... SERVICES PERSONAL COMMUNICATIONS SERVICES Technical Standards § 24.55 Antenna structures; air navigation safety. Licensees that own their antenna structures must not allow these antenna structures to become...

  8. 47 CFR 24.55 - Antenna structures; air navigation safety.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 2 2011-10-01 2011-10-01 false Antenna structures; air navigation safety. 24... SERVICES PERSONAL COMMUNICATIONS SERVICES Technical Standards § 24.55 Antenna structures; air navigation safety. Licensees that own their antenna structures must not allow these antenna structures to become...

  9. 47 CFR 24.55 - Antenna structures; air navigation safety.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 47 Telecommunication 2 2013-10-01 2013-10-01 false Antenna structures; air navigation safety. 24... SERVICES PERSONAL COMMUNICATIONS SERVICES Technical Standards § 24.55 Antenna structures; air navigation safety. Licensees that own their antenna structures must not allow these antenna structures to become...

  10. 47 CFR 24.55 - Antenna structures; air navigation safety.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Antenna structures; air navigation safety. 24... SERVICES PERSONAL COMMUNICATIONS SERVICES Technical Standards § 24.55 Antenna structures; air navigation safety. Licensees that own their antenna structures must not allow these antenna structures to become...

  11. 47 CFR 24.55 - Antenna structures; air navigation safety.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 2 2012-10-01 2012-10-01 false Antenna structures; air navigation safety. 24... SERVICES PERSONAL COMMUNICATIONS SERVICES Technical Standards § 24.55 Antenna structures; air navigation safety. Licensees that own their antenna structures must not allow these antenna structures to become...

  12. Structural, morphological, and electrical characteristics of the electrodeposited cobalt oxide electrode for supercapacitor applications

    SciTech Connect

    Kandalkar, Sunil G.; Lee, Hae-Min; Chae, Heeyeop; Kim, Chang-Koo

    2011-01-15

    Cobalt oxide (Co{sub 3}O{sub 4}) thin films were prepared through electrodeposition on copper substrates using an ammonia-complexed cobalt chloride solution. The structural and morphological properties of the film were studied using an X-ray diffractometer and scanning electron microscopy, and the results showed that the electrodeposited cobalt oxide film had a nanocrystalline and porous structure. The electrochemical behavior of the electrodeposited cobalt oxide electrode was evaluated in a KOH solution using cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge-discharge tests. The electrodeposited cobalt oxide electrode exhibited a specific capacitance of 235 F/g at a scan rate of 20 mV/s. The specific energy and the specific power of the electrode were 4.0 Wh/kg and 1.33 kW/kg, respectively.

  13. Structural comparison of nickel electrodes and precursor phases

    NASA Technical Reports Server (NTRS)

    Cornilsen, Bahne C.; Shan, Xiaoyin; Loyselle, Patricia

    1989-01-01

    Researchers summarize previous Raman spectroscopic results and discuss important structural differences in the various phases of active mass and active mass precursors. Raman spectra provide unique signatures for these phases, and allow one to distinguish each phase, even when the compound is amorphous to x rays (i.e., does not scatter x rays because of a lack of order and/or small particle size). The structural changes incurred during formation, charge and discharge, cobalt addition, and aging are discussed. The oxidation states and dopant contents are explained in terms of the nonstoichiometric structures.

  14. Structure and charging kinetics of electrical double layers at large electrode voltage

    SciTech Connect

    Cagle, Clint; Feng, Guang; Qiao, Rui; Huang, Jingsong; Sumpter, Bobby G; Meunier, Vincent

    2009-01-01

    The structure and charging kinetics of electrical double layers (EDLs) at interfaces of NaCl solutions and planar electrodes are studied by molecular dynamics (MD) and Poisson Nernst Planck (PNP) simulations. Based on the MD results and prior experimental data, we show that counterion packing in planar EDLs does not reach the steric limit at electrode voltages below 1 V. In addition, we demonstrate that a PNP model, when complemented with a Stern model, can be effectively used to capture the overall charging kinetics. However, the PNP/Stern model can only give a qualitative description of the fine features of the EDL.

  15. Complex band structure under plane-wave nonlocal pseudopotential Hamiltonian of metallic wires and electrodes

    SciTech Connect

    Yang, Chao

    2009-07-17

    We present a practical approach to calculate the complex band structure of an electrode for quantum transport calculations. This method is designed for plane wave based Hamiltonian with nonlocal pseudopotentials and the auxiliary periodic boundary condition transport calculation approach. Currently there is no direct method to calculate all the evanescent states for a given energy for systems with nonlocal pseudopotentials. On the other hand, in the auxiliary periodic boundary condition transport calculation, there is no need for all the evanescent states at a given energy. The current method fills this niche. The method has been used to study copper and gold nanowires and bulk electrodes.

  16. Comparison of electrode reduction activities of Geobacter sulfurreducens and an enriched consortium in an air-cathode microbial fuel cell.

    PubMed

    Ishii, Shun'ichi; Watanabe, Kazuya; Yabuki, Soichi; Logan, Bruce E; Sekiguchi, Yuji

    2008-12-01

    An electricity-generating bacterium, Geobacter sulfurreducens PCA, was inoculated into a single-chamber, air-cathode microbial fuel cell (MFC) in order to determine the maximum electron transfer rate from bacteria to the anode. To create anodic reaction-limiting conditions, where electron transfer from bacteria to the anode is the rate-limiting step, anodes with electrogenic biofilms were reduced in size and tests were conducted using anodes of six different sizes. The smallest anode (7 cm(2), or 1.5 times larger than the cathode) achieved an anodic reaction-limiting condition as a result of a limited mass of bacteria on the electrode. Under these conditions, the limiting current density reached a maximum of 1,530 mA/m(2), and power density reached a maximum of 461 mW/m(2). Per-biomass efficiency of the electron transfer rate was constant at 32 fmol cell(-1) day(-1) (178 micromol g of protein(-1) min(-1)), a rate comparable to that with solid iron as the electron acceptor but lower than rates achieved with fumarate or soluble iron. In comparison, an enriched electricity-generating consortium reached 374 micromol g of protein(-1) min(-1) under the same conditions, suggesting that the consortium had a much greater capacity for electrode reduction. These results demonstrate that per-biomass electrode reduction rates (calculated by current density and biomass density on the anode) can be used to help make better comparisons of electrogenic activity in MFCs.

  17. Preliminary study on zinc-air battery using zinc regeneration electrolysis with propanol oxidation as a counter electrode reaction

    NASA Astrophysics Data System (ADS)

    Wen, Yue-Hua; Cheng, Jie; Ning, Shang-Qi; Yang, Yu-Sheng

    A zinc-air battery using zinc regeneration electrolysis with propanol oxidation as a counter electrode reaction is reported in this paper. It possesses functions of both zincate reduction and electrochemical preparation, showing the potential for increasing the electronic energy utilization. Charge/discharge tests and scanning electron microscopy (SEM) micrographs reveal that when a nickel sheet plated with the high-H 2-overpotential metal, cadmium, was used as the negative substrate electrode, the dendritic formation and hydrogen evolution are suppressed effectively, and granular zinc deposits become larger but relatively dense with the increase of charge time. The performance of batteries is favorable even if the charge time is as long as 5 h at the current density of 20 mA cm -2. Better discharge performance is achieved using a 'cavity-opening' configuration for the discharge cell rather than a 'gas-introducing' configuration. The highest energy efficiency is up to 59.2%. That is, the energy consumed by organic electro-synthesis can be recovered by 59.2%. Cyclic voltammograms show that the sintered nickel electrode exhibits a good electro-catalysis activity for the propanol oxidation. The increase of propanol concentration conduces to an enhancement in the organic electro-synthesis efficiency. The organic electro-synthesis current efficiency of 82% can be obtained.

  18. Porous electrode apparatus for electrodeposition of detailed metal structures or microelectronic interconnections

    DOEpatents

    Griffiths, Stewart K.; Nilson, Robert H.; Hruby, Jill M.

    2002-01-01

    An apparatus and procedure for performing microfabrication of detailed metal structures by electroforming metal deposits within small cavities. Two primary areas of application are: the LIGA process which manufactures complex three-dimensional metal parts and the damascene process used for electroplating line and via interconnections of microelectronic devices. A porous electrode held in contact or in close proximity with a plating substrate or mold top to ensure one-dimensional and uniform current flow into all mold cavities is used. Electrolyte is pumped over the exposed surface of the porous electrode to ensure uniform ion concentrations at this external surface. The porous electrode prevents electrolyte circulation within individual mold cavities, avoiding preferential enhancement of ion transport in cavities having favorable geometries. Both current flow and ion transport are one-dimensional and identical in all mold cavities, so all metal deposits grow at the same rate eliminating nonuniformities of the prior art.

  19. A very dark-and-conductive electrode based on Mo/MoOx/ITO structure

    NASA Astrophysics Data System (ADS)

    Feng, Yuanxiang; Chen, Shuming

    2016-10-01

    A dark and conductive electrode based on Mo/MoOx/ITO structure with low resistivity of 1.93 × 10-4 Ω/cm was fabricated by magnetron sputtering. The demonstrated dark electrode exhibits a low reflectance of 2.4-12.9% within the visible spectral range and average luminous reflectance of 3.3%. To improve the conductivity, pure Mo was first sputtered, followed by depositing a dark and conductive MoOx by introducing O2 flow during Mo sputtering. In order to further reduce the reflectance and set the lowest reflectance at the wavelength of 550 nm, which is most sensitive to human eyes, an ITO phase changing layer was introduced on top of the MoOx. The demonstrated dark and conductive electrode can serve as bottom contact and can potentially replace the circular polarizer for high contrast top-emitting organic light-emitting diodes.

  20. Strategies for an enzyme immobilization on electrodes: Structural and electrochemical characterizations

    NASA Astrophysics Data System (ADS)

    Ganesh, V.; Muthurasu, A.

    2012-04-01

    In this paper, we propose various strategies for an enzyme immobilization on electrodes (both metal and semiconductor electrodes). In general, the proposed methodology involves two critical steps viz., (1) chemical modification of substrates using functional monolayers [Langmuir - Blodgett (LB) films and/or self-assembled monolayers (SAMs)] and (2) anchoring of a target enzyme using specific chemical and physical interactions by attacking the terminal functionality of the modified films. Basically there are three ways to immobilize an enzyme on chemically modified electrodes. First method consists of an electrostatic interaction between the enzyme and terminal functional groups present within the chemically modified films. Second and third methods involve the introduction of nanomaterials followed by an enzyme immobilization using both the physical and chemical adsorption processes. As a proof of principle, in this work we demonstrate the sensing and catalytic activity of horseradish peroxidase (HRP) anchored onto SAM modified indium tin oxide (ITO) electrodes towards hydrogen peroxide (H2O2). Structural characterization of such modified electrodes is performed using X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and contact angle measurements. The binding events and the enzymatic reactions are monitored using electrochemical techniques mainly cyclic voltammetry (CV).

  1. Structural investigations of Pt/TiOx electrode stacks for ferroelectric thin film devices

    NASA Astrophysics Data System (ADS)

    Cao, Jiang-Li; Solbach, Axel; Klemradt, Uwe; Weirich, Thomas; Mayer, Joachim; Horn-Solle, Herbert; Böttger, Ulrich; Schorn, Peter J.; Schneller, T.; Waser, Rainer

    2006-06-01

    Effects of the thermal treatment and the fabrication process of Pb(Zr0.3Ti0.7)O3 (PZT) thin films using chemical solution deposition on Pt/TiOx electrode stacks were investigated using complementary analytical techniques including atomic force microscopy (AFM), x-ray photoelectron spectroscopy, high-resolution transmission electron microscopy, and grazing incidence x-ray reflectivity of synchrotron radiation. The surface and interface structures of the Pt/TiOx electrode stacks with different thermal treatments, and the PZT/Pt/TiOx sample were examined. The propagation of Pt hillocks on the bare Pt/TiOx electrode stacks upon the annealing was observed. AFM observations also revealed that the upper surface of the Pt bottom electrode under PZT thin film became rougher than that of the bare Pt electrode with the same thermal history. Global structural information including the density, surface or interface root-mean-square roughness, and thickness of each constituent layer in the samples were determined using x-ray reflectivity. A density decrease of the Pt layer upon the annealing or during the fabrication of PZT thin films was found from fitting the specular reflectivity, and further confirmed by the negative shift of the Yoneda peak of Pt in the diffuse reflectivity. The formation of Pt hillocks on the bare Pt electrodes was attributed to the compressive stress during the high-temperature annealing caused by the limited incorporation of Ti and O into the Pt layer. Roughening of the PZT/Pt interface was ascribed to the interaction between the compressive stress in Pt and the indentation by the PZT crystallization and grain growth during the annealing.

  2. Influence of air flow parameters on nanosecond repetitively pulsed discharges in a pin-annular electrode configuration

    NASA Astrophysics Data System (ADS)

    Heitz, Sylvain A.; Moeck, Jonas P.; Schuller, Thierry; Veynante, Denis; Lacoste, Deanna A.

    2016-04-01

    The effect of various air flow parameters on the plasma regimes of nanosecond repetitively pulsed (NRP) discharges is investigated at atmospheric pressure. The two electrodes are in a pin-annular configuration, transverse to the mean flow. The voltage pulses have amplitudes up to 15 kV, a duration of 10 ns and a repetition frequency ranging from 15 to 30 kHz. The NRP corona to NRP spark (C-S) regime transition and the NRP spark to NRP corona (S-C) regime transition are investigated for different steady and harmonically oscillating flows. First, the strong effect of a transverse flow on the C-S and S-C transitions, as reported in previous studies, is verified. Second, it is shown that the azimuthal flow imparted by a swirler does not affect the regime transition voltages. Finally, the influence of low frequency harmonic oscillations of the air flow, generated by a loudspeaker, is studied. A strong effect of frequency and amplitude of the incoming flow modulation on the NRP plasma regime is observed. Results are interpreted based on the cumulative effect of the NRP discharges and an analysis of the residence times of fluid particles in the inter-electrode region.

  3. High performance air electrode for solid oxide regenerative fuel cells fabricated by infiltration of nano-catalysts

    NASA Astrophysics Data System (ADS)

    Lee, Sung-il; Kim, Jeonghee; Son, Ji-Won; Lee, Jong-Ho; Kim, Byung-Kook; Je, Hae-June; Lee, Hae-Weon; Song, Huesup; Yoon, Kyung Joong

    2014-03-01

    A high performance air electrode fabricated by infiltration of highly active nano-catalysts into a porous scaffold is demonstrated for high-temperature solid oxide regenerative fuel cells (SORFCs). The nitrate precursor solution for Sm0.5Sr0.5CoO3 (SSC) catalyst is impregnated into a porous La0.6Sr0.4Co0.2Fe0.8O3 (LSCF)-gadolinia-doped ceria (GDC) composite backbone, and extremely fine SSC nano-particles are uniformly synthesized by in-situ crystallization at the initial stage of SORFC operation via homogeneous nucleation induced by urea decomposition. The SSC nano-catalysts are in the size range of 40-80 nm and stable against coarsening upon the SORFC operation at 750 °C. The electrochemical performance is significantly improved by incorporation of SSC nano-catalysts in both power generation and hydrogen production modes. Systematic analysis on the impedance spectra reveals that the surface modification of the air electrode with nano-catalysts remarkably accelerates the chemical surface exchange reactions for both O2 reduction and O2- oxidation, which are the major limiting processes for SORFC performance.

  4. Three-dimensional modeling of nematic liquid crystal micro-optics structures with complex patterned electrodes

    NASA Astrophysics Data System (ADS)

    Rong, Xing; Kang, Shengwu; Zhang, Xinyu; Ji, An; Xie, Changsheng; Zhang, Tianxu

    2012-11-01

    In this paper, a three-dimensional (3-D) relaxation method is used to model the dynamic response behavior of liquid crystal (LC) directors in LC micro-optics structures with complex patterned electrodes. The method is based on Frank- Oseen continuum elastic theory by using a vectorial representation. This method can deal with liquid crystal structures with arbitrary patterned electrodes, and it is quite computational stability. Different numerical results obtained according the method are as follows: (1) the nematic LC structures with complex patterned electrodes applied by a constant voltage signal, and (2) the nematic LC structures with different thickness of LC layer, and (3) the nematic LC structures with different signal voltage. The typical results include the distribution of LC directors in LC layers, the distribution of electric potential in LC layers, and the distribution of phase retardation. The results show that the method can be used to effectively predict the formation of disclination lines, which has a strong impact on the performance of LC micro-optics structures.

  5. A large-area diffuse air discharge plasma excited by nanosecond pulse under a double hexagon needle-array electrode.

    PubMed

    Liu, Zhi-Jie; Wang, Wen-Chun; Yang, De-Zheng; Wang, Sen; Zhang, Shuai; Tang, Kai; Jiang, Peng-Chao

    2014-01-01

    A large-area diffuse air discharge plasma excited by bipolar nanosecond pulse is generated under a double hexagon needle-array electrode at atmospheric pressure. The images of the diffuse discharge, electric characteristics, and the optical emission spectra emitted from the diffuse air discharge plasma are obtained. Based on the waveforms of pulse voltage and current, the power consumption, and the power density of the diffuse air discharge plasma are investigated under different pulse peak voltages. The electron density and the electron temperature of the diffuse plasma are estimated to be approximately 1.42×10(11) cm(-3) and 4.4 eV, respectively. The optical emission spectra are arranged to determine the rotational and vibrational temperatures by comparing experimental with simulated spectra. Meanwhile, the rotational and vibrational temperatures of the diffuse discharge plasma are also discussed under different pulse peak voltages and pulse repetition rates, respectively. In addition, the diffuse air discharge plasma can form an area of about 70×50 mm(2) on the surface of dielectric layer and can be scaled up to the required size.

  6. Fast fabrication of copper nanowire transparent electrodes by a high intensity pulsed light sintering technique in air.

    PubMed

    Ding, Su; Jiu, Jinting; Tian, Yanhong; Sugahara, Tohru; Nagao, Shijo; Suganuma, Katsuaki

    2015-12-14

    Copper nanowire transparent electrodes have received increasing interest due to the low price and nearly equal electrical conductivity compared with other TEs based on silver nanowires and indium tin oxide (ITO). However, a post-treatment at high temperature in an inert atmosphere or a vacuum environment was necessary to improve the conductivity of Cu NW TEs due to the easy oxidation of copper in air atmosphere, which greatly cancelled out the low price advantage of Cu NWs. Here, a high intensity pulsed light technique was introduced to sinter and simultaneously deoxygenate these Cu NWs into a highly conductive network at room temperature in air. The strong light absorption capacity of Cu NWs enabled the welding of the nanowires at contact spots, as well as the removal of the thin layer of residual organic compounds, oxides and hydroxide of copper even in air. The Cu NW TE with a sheet resistance of 22.9 Ohm sq(-1) and a transparency of 81.8% at 550 nm has been successfully fabricated within only 6 milliseconds exposure treatment, which is superior to other films treated at high temperature in a hydrogen atmosphere. The HIPL process was simple, convenient and fast to fabricate easily oxidized Cu NW TEs in large scale in an air atmosphere, which will largely extend the application of cheap Cu NW TEs.

  7. Silver nanoparticle-decorated carbon nanotubes as bifunctional gas-diffusion electrodes for zinc-air batteries

    NASA Astrophysics Data System (ADS)

    Wang, T.; Kaempgen, M.; Nopphawan, P.; Wee, G.; Mhaisalkar, S.; Srinivasan, M.

    Thin, lightweight, and flexible gas-diffusion electrodes (GDEs) based on freestanding entangled networks of single-walled carbon nanotubes (SWNTs) decorated with Ag nanoparticles (AgNPs) are tested as the air-breathing cathode in a zinc-air battery. The SWNT networks provide a highly porous surface for active oxygen absorption and diffusion. The high conductivity of SWNTs coupled with the catalytic activity of AgNPs for oxygen reduction leads to an improvement in the performance of the zinc-air cell. By modulating the pH value and the reaction time, different sizes of AgNPs are decorated uniformly on the SWNTs, as revealed by transmission electron microscopy and powder X-ray diffraction. AgNPs with sizes of 3-5 nm double the capacity and specific energy of a zinc-air battery as compared with bare SWNTs. The simplified, lightweight architecture shows significant advantages over conventional carbon-based GDEs in terms of weight, thickness and conductivity, and hence may be useful for mobile and portable applications.

  8. Optimization of hierarchical structure and nanoscale-enabled plasmonic refraction for window electrodes in photovoltaics

    NASA Astrophysics Data System (ADS)

    Han, Bing; Peng, Qiang; Li, Ruopeng; Rong, Qikun; Ding, Yang; Akinoglu, Eser Metin; Wu, Xueyuan; Wang, Xin; Lu, Xubing; Wang, Qianming; Zhou, Guofu; Liu, Jun-Ming; Ren, Zhifeng; Giersig, Michael; Herczynski, Andrzej; Kempa, Krzysztof; Gao, Jinwei

    2016-09-01

    An ideal network window electrode for photovoltaic applications should provide an optimal surface coverage, a uniform current density into and/or from a substrate, and a minimum of the overall resistance for a given shading ratio. Here we show that metallic networks with quasi-fractal structure provides a near-perfect practical realization of such an ideal electrode. We find that a leaf venation network, which possesses key characteristics of the optimal structure, indeed outperforms other networks. We further show that elements of hierarchal topology, rather than details of the branching geometry, are of primary importance in optimizing the networks, and demonstrate this experimentally on five model artificial hierarchical networks of varied levels of complexity. In addition to these structural effects, networks containing nanowires are shown to acquire transparency exceeding the geometric constraint due to the plasmonic refraction.

  9. Optimization of hierarchical structure and nanoscale-enabled plasmonic refraction for window electrodes in photovoltaics

    PubMed Central

    Han, Bing; Peng, Qiang; Li, Ruopeng; Rong, Qikun; Ding, Yang; Akinoglu, Eser Metin; Wu, Xueyuan; Wang, Xin; Lu, Xubing; Wang, Qianming; Zhou, Guofu; Liu, Jun-Ming; Ren, Zhifeng; Giersig, Michael; Herczynski, Andrzej; Kempa, Krzysztof; Gao, Jinwei

    2016-01-01

    An ideal network window electrode for photovoltaic applications should provide an optimal surface coverage, a uniform current density into and/or from a substrate, and a minimum of the overall resistance for a given shading ratio. Here we show that metallic networks with quasi-fractal structure provides a near-perfect practical realization of such an ideal electrode. We find that a leaf venation network, which possesses key characteristics of the optimal structure, indeed outperforms other networks. We further show that elements of hierarchal topology, rather than details of the branching geometry, are of primary importance in optimizing the networks, and demonstrate this experimentally on five model artificial hierarchical networks of varied levels of complexity. In addition to these structural effects, networks containing nanowires are shown to acquire transparency exceeding the geometric constraint due to the plasmonic refraction. PMID:27667099

  10. Nanoporous-Gold-Based Electrode Morphology Libraries for Investigating Structure-Property Relationships in Nucleic Acid Based Electrochemical Biosensors.

    PubMed

    Matharu, Zimple; Daggumati, Pallavi; Wang, Ling; Dorofeeva, Tatiana S; Li, Zidong; Seker, Erkin

    2017-01-31

    Nanoporous gold (np-Au) electrode coatings significantly enhance the performance of electrochemical nucleic acid biosensors because of their three-dimensional nanoscale network, high electrical conductivity, facile surface functionalization, and biocompatibility. Contrary to planar electrodes, the np-Au electrodes also exhibit sensitive detection in the presence of common biofouling media due to their porous structure. However, the pore size of the nanomatrix plays a critical role in dictating the extent of biomolecular capture and transport. Small pores perform better in the case of target detection in complex samples by filtering out the large nonspecific proteins. On the other hand, larger pores increase the accessibility of target nucleic acids in the nanoporous structure, enhancing the detection limits of the sensor at the expense of more interference from biofouling molecules. Here, we report a microfabricated np-Au multiple electrode array that displays a range of electrode morphologies on the same chip for identifying feature sizes that reduce the nonspecific adsorption of proteins but facilitate the permeation of target DNA molecules into the pores. We demonstrate the utility of the electrode morphology library in studying DNA functionalization and target detection in complex biological media with a special emphasis on revealing ranges of electrode morphologies that mutually enhance the limit of detection and biofouling resilience. We expect this technique to assist in the development of high-performance biosensors for point-of-care diagnostics and facilitate studies on the electrode structure-property relationships in potential applications ranging from neural electrodes to catalysts.

  11. Heterogeneous Configuration of a Ag Nanowire/Polymer Composite Structure for Selectively Stretchable Transparent Electrodes.

    PubMed

    Kim, Youngmin; Jun, Sungwoo; Ju, Byeong-Kwon; Kim, Jong-Woong

    2017-03-01

    One of the most important aspects that we need to consider in the design of intrinsically stretchable electrodes is that most electronic devices that can be formed on them are not stretchable themselves. This discrepancy can induce severe stress singularities at the interfaces between stiff devices and stretchable electrodes, leading to catastrophic device delamination when the substrate is stretched. Here, we suggest a novel solution to this challenge which involves introducing a photolithography-based rigid-island approach to fabricate the heterogeneous configuration of a silver nanowire (AgNW)/polymer composite structure. For this, we designed two new transparent polymers: a photopatternable polymer that is rigid yet flexible, and a stretchable polymer, both of which have identical acrylate functional groups. Patterning of the rigid polymer and subsequent overcoating of the soft polymer formed rigid island disks embedded in the soft polymer, resulting in a selectively stretchable transparent film. Strong covalent bonds instead of weak physical interactions between the polymers strengthened the cohesive force at the interface of the rigid/soft polymers. Inverted-layer processing with a percolated AgNW network was used to form a heterogeneous AgNW/polymer composite structure that can be used as a selectively stretchable transparent electrode. An optimized structural configuration prevented the resistance of the rigid electrode from varying up to a lateral strain of 70%. A repeated stretch/release test with 60% strain for 5000 cycles did not cause any severe damage to the structure, revealing that the fabricated structure was mechanically stable and reliable.

  12. Zinc-air battery: understanding the structure and morphology changes of graphene-supported CoMn(2)O(4) bifunctional catalysts under practical rechargeable conditions.

    PubMed

    Prabu, Moni; Ramakrishnan, Prakash; Nara, Hiroki; Momma, Toshiyuki; Osaka, Tetsuya; Shanmugam, Sangaraju

    2014-10-08

    Nitrogen-doped/undoped thermally reduced graphene oxide (N-rGO) decorated with CoMn2O4 (CMO) nanoparticles were synthesized using a simple one-step hydrothermal method. The activity and stability of this hybrid catalyst were evaluated by preparing air electrodes with both primary and rechargeable zinc-air batteries that consume ambient air. Further, we investigated the relationship between the physical properties and the electrochemical results for hybrid electrodes at various cycles using X-ray diffraction, scanning electron microscopy, galvanodynamic charge-discharging and electrochemical impedance spectroscopy. The structural, morphological and electrocatalytic performances confirm that CMO/N-rGO is a promising material for safe, reliable, and long-lasting air cathodes for both primary and rechargeable zinc-air batteries that consume air under ambient condition.

  13. All-solid-state lithium-sulfur batteries with three-dimensional mesoporous electrode structures

    NASA Astrophysics Data System (ADS)

    Nagao, Miki; Suzuki, Kota; Imade, Yuki; Tateishi, Mitsuru; Watanabe, Ryota; Yokoi, Toshiyuki; Hirayama, Masaaki; Tatsumi, Takashi; Kanno, Ryoji

    2016-10-01

    Although the characteristics of lithium-sulfur batteries are advantageous for various applications, batteries with liquid electrolytes show capacity fading due to the dissolution of polysulfides. All-solid-state lithium-sulfur batteries with highly reversible characteristics are developed using a three-dimensional carbon matrix framework structure for the sulfur cathode. Sulfur is introduced into a carbon replica framework with a pore size of 8-100 nm. The composite electrode structure provides high electronic conduction and allows high cathode utilization during the battery reaction. The capacity of cells using a LiAl alloy as the negative electrode and the thio-LISICON (lithium superionic conductor) electrolyte increases when the pore size of the carbon replica is decreased from 100 nm to less than 15 nm. The highest capacity is obtained for the carbon replica with a pore size of 8.6 nm and a wall thickness of 4.7 nm. An examination of the relationship between the charge-discharge capacity and the structure of carbon replicas with different pore sizes and wall thicknesses indicates that three-dimensional highly ordered mesoporous carbon with a small pore size is a promising electrode structure for lithium-sulfur all-solid-state batteries.

  14. Electronic and atomic structure and dynamics of electrode-electrolyte interfaces by computer simulation

    NASA Astrophysics Data System (ADS)

    Walbran, Sean Michael

    We have carried out simulation studies of the electrode electrolyte interface using quantum mechanical electronic structure direct dynamics and classical molecular dynamics methods. We have obtained a complete description of the electrostatic response of the copper/water interface including electronic structure of the electrode, molecular structure of the Stern layer, and a continuum treatment of the electrolyte ions. We have furthered the investigation of chlorine adsorbtion and electron transfer reactions at the interface by refining and exploring electronic structure techniques. While these techniques are currently too expensive for use in electron transfer studies, we were able to study the cuprous/cupric reaction at a copper electrode in water by incorporating features of more detailed simulations into classical molecular dynamics models. In contrast with earlier studies of ferrous/ferric electron transfer, we find that the cuprous/cupric reaction proceeds adiabatically. Results on the electron transfer rates are in reasonable agreement with new experiments carried out by out collaborators at Argonne National Laboratory.

  15. Impedance spectroscopy of highly ordered nano-porous electrodes based on Au-AAO (anodic aluminum oxide) structure.

    PubMed

    Ahn, Jaehwan; Cho, Sungbo; Min, Junhong

    2013-11-01

    Electrochemical measurements using the microelectrodes are increasingly utilized for the label-free detection of the small amount of biological materials such as DNA, protein, and cells. However, the interfacial electrode impedance increases and may hinder the detection of weak signals as the size of electrode decreases. To enhance the measurement sensitivity while reducing the electrode size, in this study, microelectrodes employing a nanoporous structure were fabricated and characterized by using electrical impedance spectroscopy. We made the highly ordered honeycomb nanoporous structure of Anodic Aluminum Oxide (AAO) by electrochemical anodizing and formed Au layer on the surface of AAO (Au/AAO) by electroless Au plating method. The electrical characteristics of the fabricated Au/AAO electrodes were evaluated by using de Levie's model derived for the pore electrodes. As a result, the interfacial electrode impedance of the fabricated Au/AAO electrodes was 2-3 order lower than the value of the planar electrodes at frequencies below 1 kHz. It implies this nanoporous electrode could be directly applied to label free detection of biomaterials.

  16. The structural transformation of the Pt( 1 1 0 ) electrode during the Cu underpotential deposition process

    NASA Astrophysics Data System (ADS)

    Endo, O.; Ikemiya, N.; Ito, M.

    2002-08-01

    The underpotential deposition (UPD) of copper on the Pt(1 1 0) electrode in 0.5 M H 2SO 4 was studied by in situ scanning tunneling microscopy and IRAS. It was revealed that UPD copper produces the (1×1) structure as long as the sample potential is kept below 670 mV (vs. standard hydrogen electrode, SHE). After potential cycles over 60 min at the range of 220-1070 mV (vs. SHE), the surface is irreversibly transformed into the (1× n) reconstructed structure. The UPD copper traces the substrate (1× n). The irregular band shift of the SO 4 stretching mode observed by IRAS is also discussed.

  17. Highly Stretchable Anisotropic Structures for Flexible Micro/nano-electrode Applications

    NASA Astrophysics Data System (ADS)

    Guo, Hao; Tang, Jun; Zhao, Miaomiao; Zhang, Wei; Yang, Jiangtao; Zhang, Binzhen; Chou, Xiujian; Liu, Jun; Xue, Chenyang; Zhang, Wendong

    2016-02-01

    The functionality of flexible metal electrodes relies on the stable performance of a metallic film. In this study, highly stretchable anisotropic structures are designed to investigate the behaviour of silver electrodes on polydimethylsiloxane. Treated using both the oxygen plasma and the surface chemical functionalization technology, the film resistivity was reduced to 5.856 × 10-9 Ω m after annealing at 150 °C for 30 min, which is equal to that of commercial silver films on glass. The maximum variation in the resistance was approximately 5.315 % with a strain of 50 % along the four directions, and the films also show remarkable tolerance to repetitive strain. These results prove the excellent anisotropy performance of these structures to minimize resistive strain sensitivity and thus enable durable flexible electronics.

  18. Synthesis of nano-structured polypyrrole/copper electrodes for nitrate and nitrite electroreduction

    NASA Astrophysics Data System (ADS)

    Phuong Thoa Nguyen, Thi; Thinh Nguyen, Viet; Nguyen Bui, Nhat; Do, Duong Kim Bao; Pham, Anh Minh

    2010-09-01

    Nanostructured polypyrrole film was synthesized onto a copper electrode in solutions of oxalic and salicylic acids and their buffers. The electrooxidation of pyrrole to form polypyrrole film and the electroreduction of nitrate and nitrite ions at synthesized Ppy modified copper electrodes (Ppy/Cu) in potassium chloride aqueous solutions were studied using chronoamperometry. The nanoporous structure of the synthesized Ppy films was characterized by scanning electron microscopy (SEM). Nitrate and nitrite reduction were performed by an electrochemical method under potentiostatic conditions. The Ppy/Cu electrodes prepared in the oxalate buffer and salicylic acid solutions perform more stable catalytic activity for nitrate reduction; their service life is about ten times longer than that for the electrodes prepared in oxalic acid solution. After 20 h of electrolysis, the nitrite was reduced completely with 100% efficiency and the nitrate was reduced with 35% efficiency. Report submitted to the 5th International Workshop on Advanced Materials Science and Nanotechnology IWAMSN, Hanoi, 9-12 November 2010.

  19. Biomimetic Ant-Nest Electrode Structures for High Sulfur Ratio Lithium-Sulfur Batteries.

    PubMed

    Ai, Guo; Dai, Yiling; Mao, Wenfeng; Zhao, Hui; Fu, Yanbao; Song, Xiangyun; En, Yunfei; Battaglia, Vincent S; Srinivasan, Venkat; Liu, Gao

    2016-09-14

    The lithium-sulfur (Li-S) rechargeable battery has the benefit of high gravimetric energy density and low cost. Significant research currently focuses on increasing the sulfur loading and sulfur/inactive-materials ratio, to improve life and capacity. Inspired by nature's ant-nest structure, this research results in a novel Li-S electrode that is designed to meet both goals. With only three simple manufacturing-friendly steps, which include slurry ball-milling, doctor-blade-based laminate casting, and the use of the sacrificial method with water to dissolve away table salt, the ant-nest design has been successfully recreated in an Li-S electrode. The efficient capabilities of the ant-nest structure are adopted to facilitate fast ion transportation, sustain polysulfide dissolution, and assist efficient precipitation. High cycling stability in the Li-S batteries, for practical applications, has been achieved with up to 3 mg·cm(-2) sulfur loading. Li-S electrodes with up to a 85% sulfur ratio have also been achieved for the efficient design of this novel ant-nest structure.

  20. Three-dimensional nanotube electrode arrays for hierarchical tubular structured high-performance pseudocapacitors

    NASA Astrophysics Data System (ADS)

    Gao, Yuan; Lin, Yuanjing; Chen, Jiaqi; Lin, Qingfeng; Wu, Yue; Su, Wenjun; Wang, Wenli; Fan, Zhiyong

    2016-07-01

    Ordered three-dimensional (3-D) tubular arrays are highly attractive candidates for high performance pseudocapacitor electrodes. Here, we report 3-D fluorine doped tin oxide (FTO) tubular arrays fabricated by a cost-effective ultrasonic spray pyrolysis (USP) method in anodic aluminum oxide (AAO) channels with high uniformity. The large surface area of such a structure leads to remarkable surface area enhancement up to 51.8 times compared to a planar structure. Combining with electrochemically deposited manganese dioxide (MnO2) nanoflakes on the inner side wall of the FTO nanotubes, the unique hierarchical tubular structured pseudocapacitor electrode demonstrated the highest areal capacitance of 193.8 mF cm-2 at the scan rate of 5 mV s-1 and 184 mF cm-2 at the discharge current density of 0.6 mA cm-2, which is 18.5 times that of a planar electrode. And it also showed a volumetric capacitance of 112.6 F cm-3 at the scan rate of 5 mV s-1 and 108.8 F cm-3 at the discharge current density of 0.6 mA cm-2. In addition, the cyclic stability test also indicated that a nanostructured pseudocapacitive electrode has a much larger capacitance retention after 3000 cycles of the charge-discharge process compared with a planar electrode, primarily due to the mechanical stability of the nanostructure. Moreover, pseudocapacitor device fabrication based on such electrodes shows the volumetric capacitance of 17.5 F cm-3, and the highest specific energy of 1.56 × 10-3 Wh cm-3. With the merit of facile fabrication procedures and largely enhanced electrochemical performance, such a 3-D structure has high potency for energy storage systems for a wide range of practical applications.Ordered three-dimensional (3-D) tubular arrays are highly attractive candidates for high performance pseudocapacitor electrodes. Here, we report 3-D fluorine doped tin oxide (FTO) tubular arrays fabricated by a cost-effective ultrasonic spray pyrolysis (USP) method in anodic aluminum oxide (AAO) channels with

  1. Surface structured platinum electrodes for the electrochemical reduction of carbon dioxide in imidazolium based ionic liquids.

    PubMed

    Hanc-Scherer, Florin A; Montiel, Miguel A; Montiel, Vicente; Herrero, Enrique; Sánchez-Sánchez, Carlos M

    2015-10-07

    The direct CO2 electrochemical reduction on model platinum single crystal electrodes Pt(hkl) is studied in [C2mim(+)][NTf2(-)], a suitable room temperature ionic liquid (RTIL) medium due to its moderate viscosity, high CO2 solubility and conductivity. Single crystal electrodes represent the most convenient type of surface structured electrodes for studying the impact of RTIL ion adsorption on relevant electrocatalytic reactions, such as surface sensitive electrochemical CO2 reduction. We propose here based on cyclic voltammetry and in situ electrolysis measurements, for the first time, the formation of a stable adduct [C2mimH-CO2(-)] by a radical-radical coupling after the simultaneous reduction of CO2 and [C2mim(+)]. It means between the CO2 radical anion and the radical formed from the reduction of the cation [C2mim(+)] before forming the corresponding electrogenerated carbene. This is confirmed by the voltammetric study of a model imidazolium-2-carboxylate compound formed following the carbene pathway. The formation of that stable adduct [C2mimH-CO2(-)] blocks CO2 reduction after a single electron transfer and inhibits CO2 and imidazolium dimerization reactions. However, the electrochemical reduction of CO2 under those conditions provokes the electrochemical cathodic degradation of the imidazolium based RTIL. This important limitation in CO2 recycling by direct electrochemical reduction is overcome by adding a strong acid, [H(+)][NTf2(-)], into solution. Then, protons become preferentially adsorbed on the electrode surface by displacing the imidazolium cations and inhibiting their electrochemical reduction. This fact allows the surface sensitive electro-synthesis of HCOOH from CO2 reduction in [C2mim(+)][NTf2(-)], with Pt(110) being the most active electrode studied.

  2. Catalytic activity for nitrate electroreduction of nano-structured polypyrrole films electrochemically synthesized onto a copper electrode

    NASA Astrophysics Data System (ADS)

    Phuong Thoa Nguyen, Thi; Thinh Nguyen, Viet; Hai Le, Viet

    2010-03-01

    Polypyrrole film was synthesized electrochemically onto a copper electrode in oxalate, oxalic acid and salicylic acid solutions. The electrochemical oxidation of pyrrole to form polypyrrole film and the electroreduction of nitrate and nitrite ions at synthesized Ppy modified copper electrodes (Ppy/Cu) in potassium chloride aqueous solutions were studied by cyclic voltammetry. Polypyrrole nano-porous film formation and the activity of the modified Ppy/Cu electrode for nitrate reduction were found to be dependent on the synthesis medium and conditions: pH; content and concentrations of the electrolytes; pyrrole concentration; electrode potential; electrolysis duration; drying time and temperature for finishing the Ppy/Cu electrode and immersion time in water for storing the Ppy/Cu electrode before use. High catalytic activity for nitrate reduction was found for composite electrodes with nano-porous structured Ppy films. The Ppy/Cu electrodes prepared in oxalate buffer and salicylic acid solutions perform more stable catalytic activity for nitrate reduction; their service life is about ten times longer than for an electrode prepared in oxalic acid solution.

  3. Iron-Air Rechargeable Battery

    NASA Technical Reports Server (NTRS)

    Narayan, Sri R. (Inventor); Prakash, G.K. Surya (Inventor); Kindler, Andrew (Inventor)

    2014-01-01

    Embodiments include an iron-air rechargeable battery having a composite electrode including an iron electrode and a hydrogen electrode integrated therewith. An air electrode is spaced from the iron electrode and an electrolyte is provided in contact with the air electrode and the iron electrodes. Various additives and catalysts are disclosed with respect to the iron electrode, air electrode, and electrolyte for increasing battery efficiency and cycle life.

  4. Generation of large-scale, barrier-free diffuse plasmas in air at atmospheric pressure using array wire electrodes and nanosecond high-voltage pulses

    SciTech Connect

    Teng, Yun; Li, Lee Liu, Yun-Long; Liu, Lun; Liu, Minghai

    2014-10-15

    This paper introduces a method to generate large-scale diffuse plasmas by using a repetition nanosecond pulse generator and a parallel array wire-electrode configuration. We investigated barrier-free diffuse plasmas produced in the open air in parallel and cross-parallel array line-line electrode configurations. We found that, when the distance between the wire-electrode pair is small, the discharges were almost extinguished. Also, glow-like diffuse plasmas with little discharge weakening were obtained in an appropriate range of line-line distances and with a cathode-grounding cross-electrode configuration. As an example, we produced a large-scale, stable diffuse plasma with volumes as large as 18 × 15 × 15 cm{sup 3}, and this discharge region can be further expanded. Additionally, using optical and electrical measurements, we showed that the electron temperature was higher than the gas temperature, which was almost the same as room temperature. Also, an array of electrode configuration with more wire electrodes had helped to prevent the transition from diffuse discharge to arc discharge. Comparing the current waveforms of configurations with 1 cell and 9 cells, we found that adding cells significantly increased the conduction current and the electrical energy delivered in the electrode gaps.

  5. Generation of large-scale, barrier-free diffuse plasmas in air at atmospheric pressure using array wire electrodes and nanosecond high-voltage pulses

    NASA Astrophysics Data System (ADS)

    Teng, Yun; Li, Lee; Liu, Yun-Long; Liu, Lun; Liu, Minghai

    2014-10-01

    This paper introduces a method to generate large-scale diffuse plasmas by using a repetition nanosecond pulse generator and a parallel array wire-electrode configuration. We investigated barrier-free diffuse plasmas produced in the open air in parallel and cross-parallel array line-line electrode configurations. We found that, when the distance between the wire-electrode pair is small, the discharges were almost extinguished. Also, glow-like diffuse plasmas with little discharge weakening were obtained in an appropriate range of line-line distances and with a cathode-grounding cross-electrode configuration. As an example, we produced a large-scale, stable diffuse plasma with volumes as large as 18 × 15 × 15 cm3, and this discharge region can be further expanded. Additionally, using optical and electrical measurements, we showed that the electron temperature was higher than the gas temperature, which was almost the same as room temperature. Also, an array of electrode configuration with more wire electrodes had helped to prevent the transition from diffuse discharge to arc discharge. Comparing the current waveforms of configurations with 1 cell and 9 cells, we found that adding cells significantly increased the conduction current and the electrical energy delivered in the electrode gaps.

  6. Highly conductive and flexible color filter electrode using multilayer film structure

    NASA Astrophysics Data System (ADS)

    Han, Jun Hee; Kim, Dong-Young; Kim, Dohong; Choi, Kyung Cheol

    2016-07-01

    In this paper, a high performance flexible component that serves as a color filter and an electrode simultaneously is suggested. The suggested highly conductive and flexible color filter electrode (CFE) has a multilayer film structure composed of silver (Ag) and tungsten trioxide (WO3). The CFE maintained its color filtering capability even when the films were bent on a polyethylene terephthalate (PET) film. Low sheet resistance of the CFE was obtained using WO3 as a bridge layer that connects two Ag layers electrically. The sheet resistance was less than 2 Ω/sq. and it was negligibly changed after bending the film, confirming the flexibility of the CFE. The CFE can be easily fabricated using a thermal evaporator and is easily patterned by photolithography or a shadow mask. The proposed CFE has enormous potential for applications involving optical devices including large area devices and flexible devices.

  7. Highly conductive and flexible color filter electrode using multilayer film structure.

    PubMed

    Han, Jun Hee; Kim, Dong-Young; Kim, Dohong; Choi, Kyung Cheol

    2016-07-04

    In this paper, a high performance flexible component that serves as a color filter and an electrode simultaneously is suggested. The suggested highly conductive and flexible color filter electrode (CFE) has a multilayer film structure composed of silver (Ag) and tungsten trioxide (WO3). The CFE maintained its color filtering capability even when the films were bent on a polyethylene terephthalate (PET) film. Low sheet resistance of the CFE was obtained using WO3 as a bridge layer that connects two Ag layers electrically. The sheet resistance was less than 2 Ω/sq. and it was negligibly changed after bending the film, confirming the flexibility of the CFE. The CFE can be easily fabricated using a thermal evaporator and is easily patterned by photolithography or a shadow mask. The proposed CFE has enormous potential for applications involving optical devices including large area devices and flexible devices.

  8. Highly conductive and flexible color filter electrode using multilayer film structure

    PubMed Central

    Han, Jun Hee; Kim, Dong-Young; Kim, Dohong; Choi, Kyung Cheol

    2016-01-01

    In this paper, a high performance flexible component that serves as a color filter and an electrode simultaneously is suggested. The suggested highly conductive and flexible color filter electrode (CFE) has a multilayer film structure composed of silver (Ag) and tungsten trioxide (WO3). The CFE maintained its color filtering capability even when the films were bent on a polyethylene terephthalate (PET) film. Low sheet resistance of the CFE was obtained using WO3 as a bridge layer that connects two Ag layers electrically. The sheet resistance was less than 2 Ω/sq. and it was negligibly changed after bending the film, confirming the flexibility of the CFE. The CFE can be easily fabricated using a thermal evaporator and is easily patterned by photolithography or a shadow mask. The proposed CFE has enormous potential for applications involving optical devices including large area devices and flexible devices. PMID:27373804

  9. 103. North Carolina Route 1130 grade separation structure at Air ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    103. North Carolina Route 1130 grade separation structure at Air Bellows Gap. Elevation view of concrete slab bridge built in 1937. Looking southeast. - Blue Ridge Parkway, Between Shenandoah National Park & Great Smoky Mountains, Asheville, Buncombe County, NC

  10. 104. North Carolina Route 1130 grade separation structure at Air ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    104. North Carolina Route 1130 grade separation structure at Air Bellows Gap. Detail of the stepped wing wall. Looking southwest. - Blue Ridge Parkway, Between Shenandoah National Park & Great Smoky Mountains, Asheville, Buncombe County, NC

  11. 105. North Carolina Route 1130 grade separation structure at Air ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    105. North Carolina Route 1130 grade separation structure at Air Bellows Gap. View showing the access road from the parkway. - Blue Ridge Parkway, Between Shenandoah National Park & Great Smoky Mountains, Asheville, Buncombe County, NC

  12. 16. Photograph of Structural Building Plans. Naval Air Station ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    16. Photograph of Structural Building Plans. - Naval Air Station Fallon, 100-man Fallout Shelter, 800 Complex, off Carson Road near intersection of Pasture & Berney Roads, Fallon, Churchill County, NV

  13. Air pollution effects on the structure of Citrus aurantium leaves

    SciTech Connect

    Psaras, G.K.; Christodoulakis, N.S.

    1987-09-01

    Individual air pollutants cause acute and chronic plant injury, act on stomata and affect carbon dioxide exchange as well as plant growth and development. Inhibition of photosynthesis by several air pollutants has been reported repeatedly. Besides, structural modifications of cell organelles have been reported after fumigation by SO/sub 2/. Although chlorosis and subsequent necrosis are common phenomena caused by artificial treatment with pollutants, fine structural leaf characteristics of plants exposed to long-term air pollution in natural conditions are little explored. Light microscope examination of air pollution affected leaves of plants common in natural ecosystems of Athens' metropolitan area revealed chlorosis phenomena. Electron microscope examination of the leaves of a common subshrub of greek phryganic formations grown in a heavily air polluted natural ecosystem of Athens metropolitan area revealed pronounced ultrastructural anomalies of chloroplasts, mitochondria and microbodies of the mesophyll cells. This organelle destruction of the photosynthesizing tissue as well as the minimization of the ecosystem primary productivity are attributed to the compound action of several toxic air pollutants of the photochemical smog of Athens. This work describes the long-term air pollution effects on the structural features of the leaves of Citrus aurantium, a decorative species planted throughout the heavily air polluted city of Athens.

  14. In Situ-Grown ZnCo2O4 on Single-Walled Carbon Nanotubes as Air Electrode Materials for Rechargeable Lithium–Oxygen Batteries

    SciTech Connect

    Liu, Bin; Xu, Wu; Yan, Pengfei; Bhattacharya, Priyanka; Cao, Ruiguo; Bowden, Mark E.; Engelhard, Mark H.; Wang, Chong M.; Zhang, Jiguang

    2015-10-12

    Although lithium-oxygen (Li-O2) batteries have great potential to be used as one of the next generation energy storage systems due to their ultrahigh theoretical specific energy, there are still many significant barriers before their practical applications. These barriers include electrolyte and electrode instability, poor ORR/OER efficiency and cycling capability, etc. Development of a highly efficient catalyst will not only enhance ORR/OER efficiency, it may also improve the stability of electrolyte because the reduced charge voltage. Here we report the synthesis of nano-sheet-assembled ZnCo2O4 spheres/single walled carbon nanotubes (ZCO/SWCNTs) composites as high performance air electrode materials for Li-O2 batteries. The ZCO catalyzed SWCNTs electrodes delivered high discharge capacities, decreased the onset of oxygen evolution reaction by 0.9 V during charge processes, and led to more stable cycling stability. These results indicate that ZCO/SWCNTs composite can be used as highly efficient air electrode for oxygen reduction and evolution reactions. The highly enhanced catalytic activity by uniformly dispersed ZnCo2O4 catalyst on nanostructured electrodes is expected to inspire

  15. Binder-Free and Carbon-Free 3D Porous Air Electrode for Li-O2 Batteries with High Efficiency, High Capacity, and Long Life.

    PubMed

    Luo, Wen-Bin; Gao, Xuan-Wen; Shi, Dong-Qi; Chou, Shu-Lei; Wang, Jia-Zhao; Liu, Hua-Kun

    2016-06-01

    Pt-Gd alloy polycrystalline thin film is deposited on 3D nickel foam by pulsed laser deposition method serving as a whole binder/carbon-free air electrode, showing great catalytic activity enhancement as an efficient bifunctional catalyst for the oxygen reduction and evolution reactions in lithium oxygen batteries. The porous structure can facilitate rapid O2 and electrolyte diffusion, as well as forming a continuous conductive network throughout the whole energy conversion process. It shows a favorable cycle performance in the full discharge/charge model, owing to the high catalytic activity of the Pt-Gd alloy composite and 3D porous nickel foam structure. Specially, excellent cycling performance under capacity limited mode is also demonstrated, in which the terminal discharge voltage is higher than 2.5 V and the terminal charge voltage is lower than 3.7 V after 100 cycles at a current density of 0.1 mA cm(-2) . Therefore, this electrocatalyst is a promising bifunctional electrocatalyst for lithium oxygen batteries and this depositing high-efficient electrocatalyst on porous substrate with polycrystalline thin film by pulsed laser deposition is also a promising technique in the future lithium oxygen batteries research.

  16. Electronic structure of low work function electrodes modified by C{sub 16}H{sub 33}SH

    SciTech Connect

    Lee, Hyunbok; Cho, Sang Wan; Park, Sang Han; Cho, Mann-Ho; Yi, Yeonjin

    2014-10-15

    Highlights: • The electronic structure of pentacene/C{sub 16}H{sub 33}SH/Au is investigated. • The work function of Au is significantly decreased with C{sub 16}H{sub 33}SH treatment. • The reduced work function is attributed to its permanent dipole moment. - Abstract: Organic and printed electronics technologies require electrodes with low work functions to facilitate the transport of electrons in and out of various optoelectronic devices. We show that the surface modifier of 1-hexadecanethiol reduces the work function of conductors using in situ ultraviolet photoemission spectroscopy, and we combine experimental and theoretical methods to investigate the origin of the work function changes. The interfacial electronic structures of pentacene/1-hexadecanethiol/Au were investigated via in situ ultraviolet photoemission spectroscopy and X-ray photoemission spectroscopy in order to understand the change in the carrier injection barrier and chemical reactions upon surface modification. Theoretical calculations using density functional theory were also performed to understand the charge distribution of 1-hexadecanethiol, which affects the reduction of the work function. The 1-hexadecanethiol surface modifier is processed in air from solution, providing an appealing alternative to chemically-reactive low-work-function metals.

  17. High rate, long cycle life battery electrode materials with an open framework structure

    DOEpatents

    Wessells, Colin; Huggins, Robert; Cui, Yi; Pasta, Mauro

    2015-02-10

    A battery includes a cathode, an anode, and an aqueous electrolyte disposed between the cathode and the anode and including a cation A. At least one of the cathode and the anode includes an electrode material having an open framework crystal structure into which the cation A is reversibly inserted during operation of the battery. The battery has a reference specific capacity when cycled at a reference rate, and at least 75% of the reference specific capacity is retained when the battery is cycled at 10 times the reference rate.

  18. Highly flexible, hybrid-structured indium tin oxides for transparent electrodes on polymer substrates

    SciTech Connect

    Triambulo, Ross E.; Kim, Jung-Hoon; Park, Jin-Woo; Na, Min-Young; Chang, Hye-Jung

    2013-06-17

    We developed highly flexible, hybrid-structured crystalline indium tin oxide (ITO) for use as transparent electrodes on polymer substrates by embedding Ag nanoparticles (AgNPs) into the substrate. The hybrid ITO consists of domains in one orientation grown on the AgNPs and a matrix of the other orientation. The domains are stronger than the matrix and function as barriers to crack propagation. As a result, both the critical bending radius (r{sub c}) (under which the resistivity change ({Delta}{rho}) is less than a given value) and the change in {Delta}{rho} with decreasing r significantly decreased in the hybrid ITO compared with homogenous ITO.

  19. Investigation of electrolyte wetting in lithium ion batteries: Effects of electrode pore structures and solution

    NASA Astrophysics Data System (ADS)

    Sheng, Yangping

    and surface tension of electrolyte is used to reflect performance of electrolyte wetting. There are very few reports about quantitative measurement about electrolyte wetting. Moreover, there are only simple qualitative observations, good, poor, and fair, were reported on the wettability of microporous separators. Therefore, development of a quantitative analysis method is critical to help understand the mechanism of how electrolyte wetting is affected by material properties and manufacturing processes. In this dissertation, a quantitative test method is developed to analyze the electrolyte wetting performance. Wetting rate, measured by wetting balance method, is used to quantitatively measure the speed of electrolyte wetting. The feasibility of the wetting rate is demonstrated by repeated test of wetting rate between electrolytes and electrodes. Various electrolytes from single solvents to complicated industrial level electrolytes are measured with baseline electrodes. Electrodes with different composition, active materials and manufacturing process, separator sheets with different materials and additives are also measured with baseline electrolyte. The wetting behaviors for different materials and manufacturing processes could be used to help improve the optimization of production process. It is very necessary to reveal the mechanism underlying electrolyte wetting, especially the effects of electrode pore microstructure. The Electrodes, which are composed of active material, binder and carbon black, are formed by production process (rheological processing, coating, drying), and post-production process (calendaring and slicing etc.). The pore structure is also complicated by the broad size range of pores from nanometer to tens micrometer. In this dissertation, a pore network concept, as revealed in the MIP test (mercury intrusion porosimetry), is employed to characterize the electrode pore structure. It is composed by the random pore cavity and connected part of pores

  20. Chemical and structural indicators for large redox potentials in Fe-based positive electrode materials.

    PubMed

    Melot, Brent C; Scanlon, David O; Reynaud, Marine; Rousse, Gwenaëlle; Chotard, Jean-Noël; Henry, Marc; Tarascon, Jean-Marie

    2014-07-23

    Li-ion batteries have enabled a revolution in the way portable consumer-electronics are powered and will play an important role as large-scale electrochemical storage applications like electric vehicles and grid-storage are developed. The ability to identify and design promising new positive insertion electrodes will be vital in continuing to push Li-ion technology to its fullest potential. Utilizing a combination of computational tools and structural analysis, we report new indicators which will facilitate the recognition of phases with the desired redox potential. Most importantly of these, we find there is a strong correlation between the presence of Li ions sitting in close-proximity to the redox center of polyanionic phases and the open circuit voltage in Fe-based cathodes. This common structural feature suggests that the bonding associated with Li may have a secondary inductive effect which increases the ionic character of Fe bonds beyond what is typically expected based purely on arguments of electronegativity associated with the polyanionic group. This correlation is supported by ab initio calculations which show the Bader charge increases (reflecting an increased ionicity) in a nearly linear fashion with the experimental cell potentials. These features are demonstrated to be consistent across a wide variety of compositions and structures and should help to facilitate the design of new, high-potential, and environmentally sustainable insertion electrodes.

  1. A hierarchical three-dimensional NiCo2O4 nanowire array/carbon cloth as an air electrode for nonaqueous Li-air batteries.

    PubMed

    Liu, Wei-Ming; Gao, Ting-Ting; Yang, Yin; Sun, Qian; Fu, Zheng-Wen

    2013-10-14

    A 3D NiCo2O4 nanowire array/carbon cloth (NCONW/CC) was employed as the cathode for Li-air batteries with a non-aqueous electrolyte. After its discharge, novel porous ball-like Li2O2 was found to be deposited on the tip of NiCo2O4 nanowires. The special structure of Li2O2 and active sites of catalysts are also discussed.

  2. Inverse inkjet printed gold micro electrodes for the structured deposition of epithelial cells and fibrin.

    PubMed

    Zehbe, Rolf; Gross, Ulrich; Schubert, Helmut

    2007-11-01

    The micro structured deposition of vital cells is an important challenge in tissue engineering, biosensor technology, and in all research dealing with cell-cell and cell-substrate contacts. Hence, an inkjet printing technology has been developed to manufacture Au-based micro electrodes by sputter coating inversely printed polyester-foils. These electrodes feature minimal structure sizes of 35 microm and consist of an anode and a cathode part. They were used with fibrinogenic epithelial cell suspensions to deposit human keratinocytes (HaCaT), mouse fibroblasts (L-929) and the protein fibrin by applying DC voltage. Subsequently cells were electrophoretically attracted to the anode, following exactly its shape, while the insoluble fibrin was simultaneously precipitated due to the electrically mediated polymerization of the soluble fibrinogen molecule. Furthermore, it was demonstrated that this technique is suitable to co-deposit both cell types in a layered fashion. The lower voltage boundary for successful deposition was set at approximately 0.8 V needed for the conversion of fibrinogen into fibrin, while the upper voltage boundary was set at approximately 1.85 V, when commencing electrolysis inhibited the deposition of vital cells. Subsequent to the anodic cell-fibrin deposition, cells were cultivated for up to 4 days and then characterized by FDA+EB staining, methyl violet staining, MNF staining and SEM. The conversion from fibrinogen into fibrin was studied using ATR/FTIR.

  3. Graphene/polyaniline composite sponge of three-dimensional porous network structure as supercapacitor electrode

    NASA Astrophysics Data System (ADS)

    Jiu-Xing, Jiang; Xu-Zhi, Zhang; Zhen-Hua, Wang; Jian-Jun, Xu

    2016-04-01

    As a supercapacitor electrode, the graphene/polyaniline (PANI) composite sponge with a three-dimensional (3D) porous network structure is synthesized by a simple three-step method. The three steps include an in situ polymerization, freeze-drying and reduction by hydrazine vapor. The prepared sponge has a large specific surface area and porous network structure, so it is in favor of spreading the electrolyte ion and increasing the charge transfer efficiency of the system. The process of preparation is simple, easy to operate and low cost. The composite sponge shows better electrochemical performance than the pure individual graphene sponge while PANI cannot keep the shape of a sponge. Such a composite sponge exhibits specific capacitances of 487 F·g-1 at 2 mV/s compared to pristine PANI of 397 F·g-1. Project supported by the Natural Science Foundation from Harbin University of Science and Technology and Harbin Institute of Technology.

  4. Manufacturing of Protected Lithium Electrodes for Advanced Lithium-Air, Lithium-Water & Lithium-Sulfur Batteries

    SciTech Connect

    Visco, Steven J

    2015-11-30

    The global demand for rechargeable batteries is large and growing rapidly. Assuming the adoption of electric vehicles continues to increase, the need for smaller, lighter, and less expensive batteries will become even more pressing. In this vein, PolyPlus Battery Company has developed ultra-light high performance batteries based on its proprietary protected lithium electrode (PLE) technology. The Company’s Lithium-Air and Lithium-Seawater batteries have already demonstrated world record performance (verified by third party testing), and we are developing advanced lithium-sulfur batteries which have the potential deliver high performance at low cost. In this program PolyPlus Battery Company teamed with Corning Incorporated to transition the PLE technology from bench top fabrication using manual tooling to a pre- commercial semi-automated pilot line. At the inception of this program PolyPlus worked with a Tier 1 battery manufacturing engineering firm to design and build the first-of-its-kind pilot line for PLE production. The pilot line was shipped and installed in Berkeley, California several months after the start of the program. PolyPlus spent the next two years working with and optimizing the pilot line and now produces all of its PLEs on this line. The optimization process successfully increased the yield, throughput, and quality of PLEs produced on the pilot line. The Corning team focused on fabrication and scale-up of the ceramic membranes that are key to the PLE technology. PolyPlus next demonstrated that it could take Corning membranes through the pilot line process to produce state-of-the-art protected lithium electrodes. In the latter part of the program the Corning team developed alternative membranes targeted for the large rechargeable battery market. PolyPlus is now in discussions with several potential customers for its advanced PLE-enabled batteries, and is building relationships and infrastructure for the transition into manufacturing. It is likely

  5. Self-supported metallic nanopore arrays with highly oriented nanoporous structures as ideally nanostructured electrodes for supercapacitor applications.

    PubMed

    Zhao, Huaping; Wang, Chengliang; Vellacheri, Ranjith; Zhou, Min; Xu, Yang; Fu, Qun; Wu, Minghong; Grote, Fabian; Lei, Yong

    2014-12-03

    Self-supported metallic nanopore arrays with highly oriented nanoporous structures are fabricated and applied as ideally nanostructured electrodes for supercapacitor applications. Their large specific surface area can ensure a high capacitance, and their highly oriented and stable nanoporous structure can facilitate ion transport.

  6. Atomic-scale structure evolution in a quasi-equilibrated electrochemical process of electrode materials for rechargeable batteries.

    PubMed

    Gu, Lin; Xiao, Dongdong; Hu, Yong-Sheng; Li, Hong; Ikuhara, Yuichi

    2015-04-01

    Lithium-ion batteries have proven to be extremely attractive candidates for applications in portable electronics, electric vehicles, and smart grid in terms of energy density, power density, and service life. Further performance optimization to satisfy ever-increasing demands on energy storage of such applications is highly desired. In most of cases, the kinetics and stability of electrode materials are strongly correlated to the transport and storage behaviors of lithium ions in the lattice of the host. Therefore, information about structural evolution of electrode materials at an atomic scale is always helpful to explain the electrochemical performances of batteries at a macroscale. The annular-bright-field (ABF) imaging in aberration-corrected scanning transmission electron microscopy (STEM) allows simultaneous imaging of light and heavy elements, providing an unprecedented opportunity to probe the nearly equilibrated local structure of electrode materials after electrochemical cycling at atomic resolution. Recent progress toward unraveling the atomic-scale structure of selected electrode materials with different charge and/or discharge state to extend the current understanding of electrochemical reaction mechanism with the ABF and high angle annular dark field STEM imaging is presented here. Future research on the relationship between atomic-level structure evolution and microscopic reaction mechanisms of electrode materials for rechargeable batteries is envisaged.

  7. Supercapacitor electrode materials with hierarchically structured pores from carbonization of MWCNTs and ZIF-8 composites.

    PubMed

    Li, Xueqin; Hao, Changlong; Tang, Bochong; Wang, Yue; Liu, Mei; Wang, Yuanwei; Zhu, Yihua; Lu, Chenguang; Tang, Zhiyong

    2017-02-09

    Due to their high specific surface area and good electric conductivity, nitrogen-doped porous carbons (NPCs) and carbon nanotubes (CNTs) have attracted much attention for electrochemical energy storage applications. In the present work, we firstly prepared MWCNT/ZIF-8 composites by decoration of zeolitic imidazolate frameworks (ZIF-8) onto the surface of multi-walled CNTs (MWCNTs), then obtained MWCNT/NPCs by the direct carbonization of MWCNT/ZIF-8. By controlling the reaction conditions, MWCNT/ZIF-8 with three different particle sizes were synthesized. The effect of NPCs size on capacitance performance has been evaluated in detail. The MWCNT/NPC with large-sized NPC (MWCNT/NPC-L) displayed the highest specific capacitance of 293.4 F g(-1) at the scan rate of 5 mV s(-1) and only lost 4.2% of capacitance after 10 000 cyclic voltammetry cycles, which was attributed to the hierarchically structured pores, N-doping and high electrical conductivity. The studies of symmetric two-electrode supercapacitor cells also confirmed MWCNT/NPC-L as efficient electrode materials that have good electrochemical performance, especially for high-rate applications.

  8. Sulfonated silica-based fuel cell electrode structures for low humidity applications

    NASA Astrophysics Data System (ADS)

    Eastcott, Jennie I.; Easton, E. Bradley

    2014-01-01

    Ceramic carbon electrodes (CCEs) are prospective candidates for use in proton exchange membrane fuel cells due to their high surface area, water retention properties, and durable nature. We have determined that incorporating small amounts of sulfonated silane in the CCE structure can lead to a profound enhancement of catalytic activity and proton conductivity. To evaluate the usefulness of a new catalyst layer for practical use, performance of the materials under various conditions must be considered. We have compared the properties of membrane electrode assemblies (MEA) prepared with CCE cathode catalyst layers to that of an MEA prepared with Nafion-based cathode catalyst layers. The MEAs were characterized via transmission electron microscopy, thermogravimetric analysis, infrared spectroscopy, and BET analysis. Fuel cell performance using different cathode gas relative humidity (RH) feed conditions was monitored using electrochemical impedance spectroscopy and polarization curves. Our CCE cathode materials maintained stable performance and had improved water management capabilities at low relative humidities, whereas Nafion-containing cathodes have performed poorly. The enhanced performance and tolerance to low RH is explained in terms of water retention within the CCE-based MEA.

  9. In-situ Spectroscopic and Structural Studies of Electrode Materials for Advanced Battery Applications

    SciTech Connect

    Daniel A Scherson

    2013-03-14

    Techniques have been developed and implemented to gain insight into fundamental factors that affect the performance of electrodes in Li and Li-ion batteries and other energy storage devices. These include experimental strategies for monitoring the Raman scattering spectra of single microparticles of carbon and transition metal oxides as a function of their state of charge. Measurements were performed in electrolytes of direct relevance to Li and Li-Ion batteries both in the static and dynamic modes. In addition, novel strategies were devised for performing conventional experiments in ultrahigh vacuum environments under conditions which eliminate effects associated with presence of impurities, using ultrapure electrolytes, both of the polymeric and ionic liquid type that display no measurable vapor pressure. Also examined was the reactivity of conventional non aqueous solvent toward ultrapure Li films as monitored in ultrahigh vacuum with external reflection Fourier transform infrared spectroscopy. Also pursued were efforts toward developing applying Raman-scattering for monitoring the flow of charge of a real Li ion battery. Such time-resolved, spatially-resolved measurements are key to validating the results of theoretical simulations involving real electrode structures.

  10. Simulation of Electric Potentials and Ion Motion in Planar Electrode Structures for Lossless Ion Manipulations (SLIM)

    SciTech Connect

    Garimella, Sandilya V. B; Ibrahim, Yehia M.; Webb, Ian K.; Tolmachev, Aleksey V.; Zhang, Xinyu; Prost, Spencer A.; Anderson, Gordon A.; Smith, Richard D.

    2014-09-26

    Here we report a conceptual study and computational evaluation of novel planar electrode Structures for Lossless Ion Manipulations (SLIM). Planar electrode SLIM devices were designed that allow for flexible ion confinement, transport and storage using a combination of RF and DC fields. Effective potentials can be generated that provide near ideal regions for confining ions in the presence of a gas. Ion trajectory simulations using SIMION 8.1 demonstrated the capability for lossless ion motion in these devices over a wide m/z range and a range of electric fields at low pressures (e.g. a few torr). More complex ion manipulations, e.g. turning ions by 90° and dynamically switching selected ion species into orthogonal channels, are also feasible. Lastly, the performance of SLIM devices at ~4 torr pressure for performing ion mobility based separations (IMS) is computationally evaluated and compared to initial experimental results, and both of which agree closely with experimental and theoretical IMS performance for a conventional drift tube design.

  11. Simulation of Electric Potentials and Ion Motion in Planar Electrode Structures for Lossless Ion Manipulations (SLIM)

    PubMed Central

    Garimella, Sandilya V.B.; Ibrahim, Yehia M.; Webb, Ian K.; Tolmachev, Aleksey V.; Zhang, Xinyu; Prost, Spencer A.; Anderson, Gordon A.; Smith, Richard D.

    2014-01-01

    We report a conceptual study and computational evaluation of novel planar electrode Structures for Lossless Ion Manipulations (SLIM). Planar electrode SLIM devices were designed that allow for flexible ion confinement, transport and storage using a combination of RF and DC fields. Effective potentials can be generated that provide near ideal regions for confining and manipulating ions in the presence of a gas. Ion trajectory simulations using SIMION 8.1 demonstrated the capability for lossless ion motion in these devices over a wide m/z range and a range of electric fields at low pressures (e.g. a few torr). More complex ion manipulations, e.g. turning ions by 90° and dynamically switching selected ion species into orthogonal channels, are also shown feasible. The performance of SLIM devices at ~4 torr pressure for performing ion mobility based separations (IMS) is computationally evaluated and compared to initial experimental results, and both of which are also shown to agree closely with experimental and theoretical IMS performance for a conventional drift tube design. PMID:25257188

  12. Simulation of Electric Potentials and Ion Motion in Planar Electrode Structures for Lossless Ion Manipulations (SLIM)

    DOE PAGES

    Garimella, Sandilya V. B; Ibrahim, Yehia M.; Webb, Ian K.; ...

    2014-09-26

    Here we report a conceptual study and computational evaluation of novel planar electrode Structures for Lossless Ion Manipulations (SLIM). Planar electrode SLIM devices were designed that allow for flexible ion confinement, transport and storage using a combination of RF and DC fields. Effective potentials can be generated that provide near ideal regions for confining ions in the presence of a gas. Ion trajectory simulations using SIMION 8.1 demonstrated the capability for lossless ion motion in these devices over a wide m/z range and a range of electric fields at low pressures (e.g. a few torr). More complex ion manipulations, e.g.more » turning ions by 90° and dynamically switching selected ion species into orthogonal channels, are also feasible. Lastly, the performance of SLIM devices at ~4 torr pressure for performing ion mobility based separations (IMS) is computationally evaluated and compared to initial experimental results, and both of which agree closely with experimental and theoretical IMS performance for a conventional drift tube design.« less

  13. Spring- And Air-Suspension Mechanism For Testing Structures

    NASA Technical Reports Server (NTRS)

    Woodard, Stanley E.

    1994-01-01

    Spring-and air-suspension mechanism supports weight of one end of test structure, yet allows that end to move almost completely unhindered as though it were weightless and not attached to suspension. Mechanisms of this type called "zero-spring-rate mechanisms" (ZSRM's) because they support structure in manner of spring suspension exhibiting approximately zero stiffness (zero spring rate) within some range of motion about nominal equilibrium or central support position. This suspension mechanism does not include overhead cables, which necessitate large amounts of overhead clearance and overhead support structures: suspension mechanism more compact (much smaller than structure) and supports structure from below.

  14. A new architecture as transparent electrodes for solar and IR applications based on photonic structures via soft lithography

    SciTech Connect

    Kuang, Ping

    2011-01-01

    Transparent conducting electrodes with the combination of high optical transmission and good electrical conductivity are essential for solar energy harvesting and electric lighting devices. Currently, indium tin oxide (ITO) is used because ITO offers relatively high transparency (>80%) to visible light and low sheet resistance (Rs = 10 ohms/square (Ω /2)) for electrical conduction. However, ITO is costly due to limited indium reserves, and it is brittle. These disadvantages have motivated the search for other conducting electrodes with similar or better properties. There has been research on a variety of electrode structures involving carbon nanotube networks, graphene films, nanowire and nanopatterned meshes and grids. Due to their novel characteristics in light manipulation and collection, photonic crystal structures show promise for further improvement. Here, we report on a new architecture consisting of nanoscale high aspect ratio metallic photonic structures as transparent electrodes fabricated via a combination of processes. For (Au) and silver (Ag) structures, the visible light transmission can reach as high as 80%, and the sheet resistance of the structure can be as low as 3.2Ω /2. The optical transparency of the high aspect ratio metal structures at visible wavelength range is comparable to that of ITO glass, while their sheet resistance is more than 3 times lower, which indicates a much higher electrical conductivity of the metal structures. Furthermore, the high aspect ratio metal structures have very high infrared (IR) reflection (90%) for the transverse magnetic (TM) mode, which can lead to the development of fabrication of metallic structures as IR filters for heat control applications. Investigations of interdigitated structures based on the high aspect ratio metal electrodes are ongoing to study the feasibility in smart window applications in light transmission modulation.

  15. Properties of Air Traffic Conflicts for Free and Structured Routing

    NASA Technical Reports Server (NTRS)

    Bilimoria, Karl D.; Lee, Hilda Q.

    2001-01-01

    This paper analyzes the properties of air traffic conflicts in a future free routing system against those in the current structured routing system. Simulation of en route air traffic operations (above 18,000 ft) over the contiguous United States for a 24-hour period, constructed with initial conditions from actual air traffic data, were conducted using the Future ATM Concepts Evaluation Tool (FACET). Free routes were modeled as great circle (direct) routes from origin to destination, and structured routes were derived from actual flight plans along the current system of air routes. The conflict properties analyzed in this study include: (1) Total number of conflicts; (2) Distributions of key conflict parameters; and, (3) Categorization of conflicts into independent conflicts and two types of interacting conflicts. Preliminary results (for Denver Center traffic) indicate that conflict properties in a free routing system are different from those in the current structured routing system. In particular, a free routing system has significantly fewer conflicts, involving a correspondingly smaller number of aircraft, compared to the current structured routing system. Additionally, the conflict parameter distributions indicate that free routing conflicts are less intrusive than structured routing conflicts, and would therefore require small trajectory deviations for resolution.

  16. Electrodes for sealed secondary batteries

    NASA Technical Reports Server (NTRS)

    Boies, D. B.; Child, F. T.

    1972-01-01

    Self-supporting membrane electrode structures, in which active ingredients and graphite are incorporated in a polymeric matrix, improve performance of electrodes in miniature, sealed, alkaline storage batteries.

  17. An uniform DBD plasma excited by bipolar nanosecond pulse using wire-cylinder electrode configuration in atmospheric air.

    PubMed

    Jiang, Peng-Chao; Wang, Wen-Chun; Zhang, Shuai; Jia, Li; Yang, De-Zheng; Tang, Kai; Liu, Zhi-Jie

    2014-03-25

    In this study, a bipolar nanosecond pulsed power supply with 15 ns rising time is employed to generate an uniform dielectric barrier discharge using the wire-cylinder electrode configuration in atmospheric air. The images, waveforms of pulse voltage and discharge current, and the optical emission spectra of the discharges are recorded. The rotational and vibrational temperatures of plasma are determined by comparing the simulated spectra with the experimental spectra. The effects of pulse peak voltage, pulse repetition rate and quartz tube diameter on the emission intensities of N2 (C(3)Πu→B(3)Πg, 0-0) and N2(+)B(2)Σu(+)→X(2)Σg(+),0-0 and the rotational and vibrational temperatures have been investigated. It is found that the uniform plasma with low gas temperature can be obtained, and the emission intensities of N2 (C(3)Πu→B(3)Πg, 0-0) and N2(+)B(2)Σu(+)→X(2)Σg(+),0-0 rise with increasing the pulse peak voltage and pulse repetition rate, while decrease as the increase of quartz tube diameter. In addition, under the condition of 28 kV pulse peak voltage, 150 Hz pulse repetition rate and 7 mm quartz tube diameter, the plasma gas temperature is determined to be 330 K. The results also indicate that the plasma gas temperature keep almost constant when increasing the pulse peak voltage and pulse repetition rate but increase with the increase of the quartz tube diameter.

  18. Charge accumulation in an MNOS structure with carrier injection from the field electrode

    SciTech Connect

    Maslovskii, V.M.; Nagin, A.P.; Chernyshev, Yu.R.

    1986-01-01

    The authors propose a method for determining the parameters of trapping centers by injecting electrons into the insulator of an MIS structure from the field electrode, when a negative voltage pulse with amplitude U and duration t is applied to it. The results indicate that in silicon nitride, just as in silicon oxide, degradation is apparently caused by the trapping of holes in traps formed by Si-H bonds. The trapping of a hole stimulates the breaking of the bond and the appearance of a mobile H/sup +/ ion. In this case, the mobile H/sup +/ ions, appearing as a result of the flow of the hole current, passivate the incomplete bonds of the silicon atoms and thereby decrease the concentration of electron-trapping centers.

  19. Superconducting proximity effect in inverted InAs/GaSb quantum well structures with Ta electrodes

    SciTech Connect

    Yu, Wenlong; Jiang, Yuxuan; Huan, Chao; Chen, Xunchi; Jiang, Zhigang; Hawkins, Samuel D.; Klem, John F.; Pan, Wei

    2014-11-10

    We present our recent electronic transport results in top-gated InAs/GaSb quantum well hybrid structures with superconducting Ta electrodes. We show that the transport across the InAs−Ta junction depends largely on the interfacial transparency, exhibiting distinct zero-bias behavior. For a relatively resistive interface, a broad conductance peak is observed at zero bias. When a transparent InAs−Ta interface is achieved, a zero-bias conductance dip appears with two coherent-peak-like features forming at bias voltages corresponding to the superconducting gap of Ta. The conductance spectra of the transparent InAs−Ta junction at different gate voltages can be fit well using the standard Blonder-Tinkham-Klapwijk theory.

  20. Electrodeposition of hierarchically structured three-dimensional nickel–iron electrodes for efficient oxygen evolution at high current densities

    PubMed Central

    Lu, Xunyu; Zhao, Chuan

    2015-01-01

    Large-scale industrial application of electrolytic splitting of water has called for the development of oxygen evolution electrodes that are inexpensive, robust and can deliver large current density (>500 mA cm−2) at low applied potentials. Here we show that an efficient oxygen electrode can be developed by electrodepositing amorphous mesoporous nickel–iron composite nanosheets directly onto macroporous nickel foam substrates. The as-prepared oxygen electrode exhibits high catalytic activity towards water oxidation in alkaline solutions, which only requires an overpotential of 200 mV to initiate the reaction, and is capable of delivering current densities of 500 and 1,000 mA cm−2 at overpotentials of 240 and 270 mV, respectively. The electrode also shows prolonged stability against bulk water electrolysis at large current. Collectively, the as-prepared three-dimensional structured electrode is the most efficient oxygen evolution electrode in alkaline electrolytes reported to the best of our knowledge, and can potentially be applied for industrial scale water electrolysis. PMID:25776015

  1. Ambient atmosphere-processable, printable Cu electrodes for flexible device applications: structural welding on a millisecond timescale of surface oxide-free Cu nanoparticles

    NASA Astrophysics Data System (ADS)

    Oh, Sang-Jin; Jo, Yejin; Lee, Eun Jung; Lee, Sun Sook; Kang, Young Hun; Jeon, Hye-Ji; Cho, Song Yun; Park, Jin-Seong; Seo, Yeong-Hui; Ryu, Beyong-Hwan; Choi, Youngmin; Jeong, Sunho

    2015-02-01

    Recently, various functional devices based on printing technologies have been of paramount interest, owing to their characteristic processing advantages along with excellent device performance. In particular, printable metallic electrodes have drawn attention in a variety of optoelectronic applications; however, research into printable metallic nanoparticles has been limited mainly to the case of an environmentally stable Ag phase. Despite its earth-abundance and highly conductive nature, the Cu phase, to date, has not been exploited as an ambient atmosphere-processable, printable material due to its critical oxidation problem in air. In this study, we demonstrate a facile route for generating highly conductive, flexible Cu electrodes in air by introducing the well-optimized photonic sintering at a time frame of 10-3 s, at which the photon energy, rather than conventional thermal energy, is instantly provided. It is elucidated here how the surface oxide-free, printed Cu particulate films undergo chemical structural/microstructural evolution depending on the instantly irradiated photon energy, and a successful demonstration is provided of large-area, flexible, printed Cu conductors on various substrates, including polyimide (PI), polyethersulfone (PES), polyethylene terephthalate (PET), and paper. The applicability of the resulting printed Cu electrodes is evaluated via implementation into both flexible capacitor devices and indium-gallium-zinc oxide (IGZO) flexible thin-film transistors.Recently, various functional devices based on printing technologies have been of paramount interest, owing to their characteristic processing advantages along with excellent device performance. In particular, printable metallic electrodes have drawn attention in a variety of optoelectronic applications; however, research into printable metallic nanoparticles has been limited mainly to the case of an environmentally stable Ag phase. Despite its earth-abundance and highly conductive

  2. Fuel electrode containing pre-sintered nickel/zirconia for a solid oxide fuel cell

    DOEpatents

    Ruka, Roswell J.; Vora, Shailesh D.

    2001-01-01

    A fuel cell structure (2) is provided, having a pre-sintered nickel-zirconia fuel electrode (6) and an air electrode (4), with a ceramic electrolyte (5) disposed between the electrodes, where the pre-sintered fuel electrode (6) contains particles selected from the group consisting of nickel oxide, cobalt and cerium dioxide particles and mixtures thereof, and titanium dioxide particles, within a matrix of yttria-stabilized zirconia and spaced-apart filamentary nickel strings having a chain structure, and where the fuel electrode can be sintered to provide an active solid oxide fuel cell.

  3. Impact of temperature and electrical potentials on the stability and structure of collagen adsorbed on the gold electrode

    NASA Astrophysics Data System (ADS)

    Meiners, Frank; Ahlers, Michael; Brand, Izabella; Wittstock, Gunther

    2015-01-01

    The morphology and structure of collagen type I adsorbed on gold electrodes were studied as a function of electrode potential and temperature by means of capacitance measurements, polarization modulation infrared reflection-absorption spectroscopy and scanning force microscopy at temperatures of 37 °C, 43 °C and 50 °C. The selected temperatures corresponded to the normal body temperature, temperature of denaturation of collagen molecules and denaturation of collagen fibrils, respectively. Independently of the solution temperature, collagen was adsorbed on gold electrodes in the potential range - 0.7 V < E < 0.4 V vs. Ag/AgCl, where the protein film was very stable. Fragments of collagen molecules made a direct contact to the gold surface and water was present in the film. Protein molecules were oriented preferentially with their long axis towards the gold surface. Collagen molecules in the adsorbed state preserved their native triple helical structure even at temperatures corresponding to collagen denaturation in aqueous solutions. Application of E < - 0.75 V vs. Ag/AgCl leads to the swelling of the protein film by water and desorption from the electrode surface. IR spectra provided no evidence of the thermal denaturation of adsorbed collagen molecules. A temperature increase to 50 °C leads to a distortion of the collagen film. The processes of aggregation and fibrilization were preferred over thermal denaturation for collagen adsorbed on the electrode surface and exposed to changing potentials.

  4. Ethanol oxidation on Pt single-crystal electrodes: surface-structure effects in alkaline medium.

    PubMed

    Busó-Rogero, Carlos; Herrero, Enrique; Feliu, Juan M

    2014-07-21

    Ethanol oxidation in 0.1 M NaOH on single-crystal electrodes has been studied using electrochemical and FTIR techniques. The results show that the activity order is the opposite of that found in acidic solutions. The Pt(111) electrode displays the highest currents and also the highest onset potential of all the electrodes. The onset potential for the oxidation of ethanol is linked to the adsorption of OH on the electrode surface. However, small (or even negligible) amounts of CO(ads) and carbonate are detected by FTIR, which implies that cleavage of the C-C bond is not favored in this medium. The activity of the electrodes diminishes quickly upon cycling. The diminution of the activity is proportional to the measured currents and is linked to the formation and polymerization of acetaldehyde, which adsorbs onto the electrode surface and prevents further oxidation.

  5. Development of Nano-structured Electrode Materials for High Performance Energy Storage System

    NASA Astrophysics Data System (ADS)

    Huang, Zhendong

    Systematic studies have been done to develop a low cost, environmental-friendly facile fabrication process for the preparation of high performance nanostructured electrode materials and to fully understand the influence factors on the electrochemical performance in the application of lithium ion batteries (LIBs) or supercapacitors. For LIBs, LiNi1/3Co1/3Mn1/3O2 (NCM) with a 1D porous structure has been developed as cathode material. The tube-like 1D structure consists of inter-linked, multi-facet nanoparticles of approximately 100-500nm in diameter. The microscopically porous structure originates from the honeycomb-shaped precursor foaming gel, which serves as self-template during the stepwise calcination process. The 1D NCM presents specific capacities of 153, 140, 130 and 118mAh·g-1 at current densities of 0.1C, 0.5C, 1C and 2C, respectively. Subsequently, a novel stepwise crystallization process consisting of a higher crystallization temperature and longer period for grain growth is employed to prepare single crystal NCM nanoparticles. The modified sol-gel process followed by optimized crystallization process results in significant improvements in chemical and physical characteristics of the NCM particles. They include a fully-developed single crystal NCM with uniform composition and a porous NCM architecture with a reduced degree of fusion and a large specific surface area. The NCM cathode material with these structural modifications in turn presents significantly enhanced specific capacities of 173.9, 166.9, 158.3 and 142.3mAh·g -1 at 0.1C, 0.5C, 1C and 2C, respectively. Carbon nanotube (CNT) is used to improve the relative low power capability and poor cyclic stability of NCM caused by its poor electrical conductivity. The NCM/CNT nanocomposites cathodes are prepared through simply mixing of the two component materials followed by a thermal treatment. The CNTs were functionalized to obtain uniformly-dispersed MWCNTs in the NCM matrix. The electrochemical

  6. Influence of ionomer content on the structure and performance of PEFC membrane electrode assemblies

    SciTech Connect

    Xie, Jian; Xu, Fan; WoodIII, David L; More, Karren Leslie; Zawodzinski, Thomas; Smith, Wayne H

    2010-01-01

    Nafion ionomer content of the cathode catalyst-layer of a polymer electrolyte fuel cell (PEFC), made by the decal hot pressing method, has been investigated for its effect on performance and structure of the membrane electrode assembly (MEA). Varying Nafion content was shown to have an effect on performance within the entire range of polarization curves (i.e. kinetic, ohmic, and mass-transport regions) as well as on the structure. AFM analysis shows the effect of Nafion on the dispersion of carbon aggregates. Further analysis using TEM demonstrates the effect of Nafion on both the dispersion of carbon aggregates and the distribution and thickness of the Nafion ionomer films surrounding the catalyst/carbon aggregates. The MEA structure change correlates well with the MEA performance on both kinetics and mass-transport region. The determining factors on the performance of MEA are the interfacial zone (between the ionomer and catalyst particle), the dispersion of catalyst/carbon aggregates and the distribution/thickness of Nafion films. An optimized Nafion content in the range of 27 6 wt.% for the cathode was determined for an E-TEK 20% Pt3Cr/C catalyst at a loading of 0.20mg Pt/cm2.

  7. A nonstoichiometric structural model to characterize changes in the nickel hydroxide electrode during cycling

    SciTech Connect

    Srinivasan, Venkat; Bahne, C. Cornilsen; Weidner, John W.

    2003-09-15

    Experimental capacities and mass changes are recorded using an electrochemical quartz crystal microbalance during the first 9 charge and discharge cycles of nickel hydroxide thin films cycled in 3.0 weight percent (wt%) potassium hydroxide electrolyte. For the first time, the film capacities have been corrected for the oxygen evolution side reaction, and the data used as input into the point defect-containing structural model to track the changes that occur during short-term cycling. Variations in capacity and mass during formation and charge/discharge cycling are related to changes in the point defect parameters, thus providing a structural origin for the unique experimental variations observed here and often reported in the literature, but previously unexplained. Proton-, potassium-, and water-content vary in the active material during charge/discharge cycling. The observed capacity loss, or ''capacity fade'', is explained by incomplete incorporation of potassium ions in (or near) the nickel vacancy during charge, as additional protons are then allowed to occupy the vacant lattice site. The increase in water content during reduction parallels the expansion of the electrode that is well known during cycling. This result confirms the origin of the swelling phenomenon as being caused by water incorporation. The model and methodology developed in this paper can be used to correlate electrochemical signatures with material chemical structure.

  8. Structural investigation of MF, RF and DC sputtered Mo thin films for backside photovoltaic electrode

    NASA Astrophysics Data System (ADS)

    Małek, Anna K.; Marszałek, Konstanty W.; Rydosz, Artur M.

    2016-12-01

    Recently photovoltaics attracts much attention of research and industry. The multidirectional studies are carried out in order to improve solar cells performance, the innovative materials are still searched and existing materials and technology are optimized. In the multilayer structure of CIGS solar cells molybdenum (Mo) layer is used as a back contact. Mo layers meet all requirements for back side electrode: low resistivity, good adhesion to the substrate, high optical reflection in the visible range, columnar structure for Na ions diffusion, formation of an ohmic contact with the ptype CIGS absorber layer, and high stability during the corrosive selenization process. The high adhesion to the substrate and low resistivity in single Mo layer is difficult to be achieved because both properties depend on the deposition parameters, particularly on working gas pressure. Therefore Mo bilayers are applied as a back contact for CIGS solar cells. In this work the Mo layers were deposited by medium frequency sputtering at different process parameters. The effect of substrate temperature within the range of 50°C-200°C and working gas pressure from 0.7 mTorr to 7 mTorr on crystalline structure of Mo layers was studied.

  9. Experimental progress with novel surface electrode ion trap structures for quantum information processing

    NASA Astrophysics Data System (ADS)

    Clark, Craig; Blain, Matthew; Benito, Francisco; Chou, Chin-Wen; Descour, Mike; Ellis, Rob; Haltli, Ray; Heller, Edwin; Kemme, Shanalyn; Sterk, Jon; Tabakov, Boyan; Tigges, Chris; Maunz, Peter; Stick, Daniel

    2013-05-01

    Segmented surface electrode ion traps are one of the most mature platforms among candidates for scalable quantum information processing. In this poster, an overview of current results from four specific projects will be presented. Two projects involve increased light collection from trapped ion for state detection and/or remote entangling of distant ions. The first involves cavity integration into a linear surface trap, and the second, involves integration of diffractive optical elements into a linear surface trap for increased light collection. Another project involves a trap with a ring geometry which could be used to trap long chains of equally spaced ions. Finally, we report on initial testing of a trap structure with vastly improved in-plane optical access. In this structure in-plane beams can be focused to less than 8 microns while keeping a distance of at least 5 beam radii to the trap structure. Along with these projects other relevant progress from Sandia National Laboratory's ion trap group will be presented. This work was supported by Sandia's Laboratory Directed Research and Development (LDRD) and the Intelligence Advanced Research Projects Activity (IARPA). Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the US Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

  10. Automated detection and labeling of high-density EEG electrodes from structural MR images

    NASA Astrophysics Data System (ADS)

    Marino, Marco; Liu, Quanying; Brem, Silvia; Wenderoth, Nicole; Mantini, Dante

    2016-10-01

    Objective. Accurate knowledge about the positions of electrodes in electroencephalography (EEG) is very important for precise source localizations. Direct detection of electrodes from magnetic resonance (MR) images is particularly interesting, as it is possible to avoid errors of co-registration between electrode and head coordinate systems. In this study, we propose an automated MR-based method for electrode detection and labeling, particularly tailored to high-density montages. Approach. Anatomical MR images were processed to create an electrode-enhanced image in individual space. Image processing included intensity non-uniformity correction, background noise and goggles artifact removal. Next, we defined a search volume around the head where electrode positions were detected. Electrodes were identified as local maxima in the search volume and registered to the Montreal Neurological Institute standard space using an affine transformation. This allowed the matching of the detected points with the specific EEG montage template, as well as their labeling. Matching and labeling were performed by the coherent point drift method. Our method was assessed on 8 MR images collected in subjects wearing a 256-channel EEG net, using the displacement with respect to manually selected electrodes as performance metric. Main results. Average displacement achieved by our method was significantly lower compared to alternative techniques, such as the photogrammetry technique. The maximum displacement was for more than 99% of the electrodes lower than 1 cm, which is typically considered an acceptable upper limit for errors in electrode positioning. Our method showed robustness and reliability, even in suboptimal conditions, such as in the case of net rotation, imprecisely gathered wires, electrode detachment from the head, and MR image ghosting. Significance. We showed that our method provides objective, repeatable and precise estimates of EEG electrode coordinates. We hope our work

  11. Recirculating electric air filter

    DOEpatents

    Bergman, W.

    1985-01-09

    An electric air filter cartridge has a cylindrical inner high voltage electrode, a layer of filter material, and an outer ground electrode formed of a plurality of segments moveably connected together. The outer electrode can be easily opened to remove or insert filter material. Air flows through the two electrodes and the filter material and is exhausted from the center of the inner electrode.

  12. Electricity producing property and bacterial community structure in microbial fuel cell equipped with membrane electrode assembly.

    PubMed

    Rubaba, Owen; Araki, Yoko; Yamamoto, Shuji; Suzuki, Kei; Sakamoto, Hisatoshi; Matsuda, Atsunori; Futamata, Hiroyuki

    2013-07-01

    It is important for practical use of microbial fuel cells (MFCs) to not only develop electrodes and proton exchange membranes but also to understand the bacterial community structure related to electricity generation. Four lactate fed MFCs equipped with different membrane electrode assemblies (MEAs) were constructed with paddy field soil as inoculum. The MEAs significantly affected the electricity-generating properties of the MFCs. MEA-I was made with Nafion 117 solution and the other MEAs were made with different configurations of three kinds of polymers. MFC-I equipped with MEA-I exhibited the highest performance with a stable current density of 55 ± 3 mA m⁻². MFC-III equipped with MEA-III with the highest platinum concentration, exhibited the lowest performance with a stable current density of 1.7 ± 0.1 mA m⁻². SEM observation revealed that there were cracks on MEA-III. These results demonstrated that it is significantly important to prevent oxygen-intrusion for improved MFC performance. By comparing the data of DGGE and phylogenetic analyzes, it was suggested that the dominant bacterial communities of MFC-I were constructed with lactate-fermenters and Fe(III)-reducers, which consisted of bacteria affiliated with the genera of Enterobacter, Dechlorosoma, Pelobacter, Desulfovibrio, Propioniferax, Pelosinus, and Firmicutes. A bacterium sharing 100% similarity to one of the DGGE bands was isolated from MFC-I. The 16S rRNA gene sequence of the isolate shared 98% similarity to gram-positive Propioniferax sp. P7 and it was confirmed that the isolate produced electricity in an MFC. These results suggested that these bacteria are valuable for constructing the electron transfer network in MFC.

  13. Plasmonic nanostructures for electronic designs of photovoltaic devices: plasmonic hot-carrier photovoltaic architectures and plasmonic electrode structures

    NASA Astrophysics Data System (ADS)

    Zhang, Tong; Su, Dan; Li, Ruo-Zhou; Wang, Shan-Jiang; Shan, Feng; Xu, Jia-Jia; Zhang, Xiao-Yang

    2016-10-01

    The tunable and amazing properties of plasmonic nanostructures have received significant attentions in the fields of solar energy conversion. Plasmonic nanostructures provide pathways to directly convert solar energy into electric energy by hot-carrier generation. They can also serve as economical electrodes for high-efficient carrier collection. Both have promising potential for manufacturing new generation solar cells. Here, we review recent advances in plasmonic nanostructures for electronic designs of photovoltaic devices and specially focus on plasmonic hot-carrier photovoltaic architectures and plasmonic electrode structures. Technical challenges toward low-cost and high-performance plasmonics-based solar cells are also discussed.

  14. Structure, Electronic Properties, and Electrochemical Behavior of a Boron-Doped Diamond/Quartz Optically Transparent Electrode.

    PubMed

    Wächter, Naihara; Munson, Catherine; Jarošová, Romana; Berkun, Isil; Hogan, Timothy; Rocha-Filho, Romeu C; Swain, Greg M

    2016-05-31

    The morphology, microstructure, chemistry, electronic properties, and electrochemical behavior of a boron-doped nanocrystalline diamond (BDD) thin film grown on quartz were evaluated. Diamond optically transparent electrodes (OTEs) are useful for transmission spectroelectrochemical measurements, offering excellent stability during anodic and cathodic polarization and exposure to a variety of chemical environments. We report on the characterization of a BDD OTE by atomic force microscopy, optical spectroscopy, Raman spectroscopic mapping, alternating-current Hall effect measurements, X-ray photoelectron spectroscopy, and electrochemical methods. The results reported herein provide the first comprehensive study of the relationship between the physical and chemical structure and electronic properties of a diamond OTE and the electrode's electrochemical activity.

  15. Air

    MedlinePlus

    ... do to protect yourself from dirty air . Indoor air pollution and outdoor air pollution Air can be polluted indoors and it can ... this chart to see what things cause indoor air pollution and what things cause outdoor air pollution! Indoor ...

  16. Printed PEDOT layers as transparent emitter electrodes for application in flexible inorganic photovoltaic structures

    NASA Astrophysics Data System (ADS)

    Znajdek, Katarzyna; Sibiński, Maciej; Przymecki, Krzysztof; Wróblewski, Grzegorz; Lisik, Zbigniew

    2016-12-01

    The purpose of the work is to find an appropriate flexible material to replace commonly used transparent conductive oxides (TCO) in photovoltaic (PV) emitter electrode applications. Authors show the alternative, potential possibility of using PEDOT conductive polymer as transparent emitter contacts for thin-film, flexible photovoltaic structures. The vast majority of contacts made of TCO layers, dominantly indium tin oxide ITO, are electrically unstable under the influence of mechanical stresses [1,2,3]. This drawback inhibits their usage in flexible devices, such as solar cells. The need of the development in the field of flexible PV structures induces searching for new materials. Investigated transparent conductive layers (TCL) were made of organic compositions based on PEDOT polymer and their parameters were compared with equally measured parameters of carbon nanotube (CNT) layers, commercial ITO and AgHT ultra-thin silver layers. Transparent conductive layers based on PEDOT:PSS compound were deposited on flexible substrates by screen printing technique. The analysis of achieved results shows the broad spectrum of application possibilities for PEDOT layers.

  17. Composition and crystal structure of perovskite films attained from electrodes of used car battery

    NASA Astrophysics Data System (ADS)

    Dhiaputra, Ilham; Permana, Bayu; Maulana, Yusep; Inayatie, Yuniar Dwi; Purba, Yonatan R.; Bahtiar, Ayi

    2016-02-01

    Perovskite solar cells have been intensively investigated for high performance and low-cost solid-state solar cells. Perovskite based-lead materials are commonly used as active material for high power conversion efficiency solar cells. Herein, we report our study on the development of used electrodes car battery as a cheap raw lead material to be converted into lead (II) iodide PbI2 by using simple chemical method. We have successfully obtained PbI2 material with purity higher than 85% and its crystal structure is comparable with that of commercial product. The perovskite CH3NH3PbI3 film was prepared by spin-coating of PbI2 solution and followed by spin-coating two-times of methylamonium iodide (MAI) solution. In this paper, the crystal structure of perovskite film attained from used car battery is shown and compared with that of prepared from commercial PbI2. By utilizing the used car battery into perovskite valuable material for high performance solar cells, we can not only improve the economical value (added-value) of wasted car battery but also we can simultaneously save the environment.

  18. A structural study of solid electrolyte interface on negative electrode of lithium-Ion battery by electron microscopy.

    PubMed

    Matsushita, Tadashi; Watanabe, Jiro; Nakao, Tatsuya; Yamashita, Seiichi

    2014-11-01

    For the last decades, the performance of the lithium-ion battery (LIB) has been significantly improved and its applications have been expanding rapidly. However, its performance has yet to be enhanced.In the lithium-ion battery development, it is important to elucidate the electrode structure change in detail during the charge and discharge cycling. In particular, solid electrolyte interface (SEI) formed by decomposition of the electrolytes on the graphite negative electrode surface should play an important role for battery properties. Therefore, it is essential to control the structure and composition of SEI to improve the battery performance. Here, we conducted a scanning electron microscope (SEM) and transmission electron microscope (TEM) study to elucidate the structures of the SEI during the charge and discharge process using LiNi1/3Co1/3Mn1/3O2 [1] cathode and graphite anode. [2] Since SEI is a lithium-containing compound with high activity, it was observed without being exposed to the atmosphere. The electrodes including SEI were sampled after dismantling batteries with cutoff voltages of 3V and 4.2V for the charge process and 3V for the discharge process. Fig.1 shows SEM images of the graphite electrode surface during the charge and discharge process. The change of the SEI structure during the process was clearly observed. Further, TEM images showed that the SEI grew thicker during the charge process and becomes thinner when discharged. These results with regard to the reversible SEI structure could give a new insight for the battery development.jmicro;63/suppl_1/i21/DFU056F1F1DFU056F1Fig. 1.SEM images of the graphite electrode surface:(a) before charge process;(b) with charge-cutoff voltage of 3.0V; (c) with charge-cutoff voltage of 4.2V; (d) with discharge-cutoff voltage of 3.0V.

  19. Importance of open pore structures with mechanical integrity in designing the cathode electrode for lithium-sulfur batteries

    NASA Astrophysics Data System (ADS)

    Kim, C.-S.; Guerfi, A.; Hovington, P.; Trottier, J.; Gagnon, C.; Barray, F.; Vijh, A.; Armand, M.; Zaghib, K.

    2013-11-01

    The robustness of conductive networks and the accessibility of electrolyte into the network are important factors in designing the cathode electrode for lithium/sulfur (Li/S) batteries containing liquid electrolytes that involve liquid phase electrochemical reactions. We show that the performance of Li/S cells can be significantly improved by simply optimizing the electrode processing conditions to have open pore structures and mechanical integrity of the electrode architecture. It is demonstrated that the capacity of 1000 mAh g-1 at 0.1 C and the stable capacity retention of >700 mAh g-1 after 200 cycles at 0.5 C can be achieved with relatively high sulfur content of 68%. 417 Wh kg-1 in specific energy and 623 Wh l-1 in energy density are achievable with this new technology.

  20. A novel high capacity positive electrode material with tunnel-type structure for aqueous sodium-ion batteries

    DOE PAGES

    Wang, Yuesheng; Mu, Linqin; Liu, Jue; ...

    2015-08-06

    In this study, aqueous sodium-ion batteries have shown desired properties of high safety characteristics and low-cost for large-scale energy storage applications such as smart grid, because of the abundant sodium resources as well as the inherently safer aqueous electrolytes. Among various Na insertion electrode materials, tunnel-type Na0.44MnO2 has been widely investigated as a positive electrode for aqueous sodium-ion batteries. However, the low achievable capacity hinders its practical applications. Here we report a novel sodium rich tunnel-type positive material with a nominal composition of Na0.66[Mn0.66Ti0.34]O2. The tunnel-type structure of Na0.44MnO2 obtained for this compound was confirmed by XRD and atomic-scale STEM/EELS.more » When cycled as positive electrode in full cells using NaTi2(PO4)3/C as negative electrode in 1M Na2SO4 aqueous electrolyte, this material shows the highest capacity of 76 mAh g-1 among the Na insertion oxides with an average operating voltage of 1.2 V at a current rate of 2C. These results demonstrate that Na0.66[Mn0.66Ti0.34]O2 is a promising positive electrode material for rechargeable aqueous sodium-ion batteries.« less

  1. Numerical evaluation of moiré pattern in touch sensor module with electrode mesh structure in oblique view

    NASA Astrophysics Data System (ADS)

    Pournoury, M.; Zamiri, A.; Kim, T. Y.; Yurlov, V.; Oh, K.

    2016-03-01

    Capacitive touch sensor screen with the metal materials has recently become qualified for substitution of ITO; however several obstacles still have to be solved. One of the most important issues is moiré phenomenon. The visibility problem of the metal-mesh, in touch sensor module (TSM) is numerically considered in this paper. Based on human eye contract sensitivity function (CSF), moiré pattern of TSM electrode mesh structure is simulated with MATLAB software for 8 inch screen display in oblique view. Standard deviation of the generated moiré by the superposition of electrode mesh and screen image is calculated to find the optimal parameters which provide the minimum moiré visibility. To create the screen pixel array and mesh electrode, rectangular function is used. The filtered image, in frequency domain, is obtained by multiplication of Fourier transform of the finite mesh pattern (product of screen pixel and mesh electrode) with the calculated CSF function for three different observer distances (L=200, 300 and 400 mm). It is observed that the discrepancy between analytical and numerical results is less than 0.6% for 400 mm viewer distance. Moreover, in the case of oblique view due to considering the thickness of the finite film between mesh electrodes and screen, different points of minimum standard deviation of moiré pattern are predicted compared to normal view.

  2. Electrode fabrication for high-speed polarization mode converter

    NASA Astrophysics Data System (ADS)

    Meng, X.; Zhang, S.; Chen, C.; Poirier, M.; Shepherd, F. R.; Das, S. R.

    2004-05-01

    As part of the development of a traveling wave polarization converter (TWPC), a technique for producing ``T-electrodes'' adjacent to the ridge sidewalls and air bridges has been developed. To maximize the conversion efficiency, the rf electrodes on the etched floor are required to be very close to the ridge sidewalls. In the fabrication of the electrode, patterned seed layer stripes were first put on the etched floor on both sides of the waveguide by a metal lift-off process. Onto this seed layer, the T-electrode was electroplated through a patterned thick photoresist. After resist removal, the unwanted seed layer was stripped off by chemical etch back. Through this multistep process, the electrodes were constructed successfully with the desired proximity to the ridge waveguide. For easy chip assembly, the bond pads were designed to be on the same side of the device. Two long and wide metal air bridges over the ridge waveguide were made to connect the electrode on one side to the bond pads on the other side of the ridge. It was found that the air bridges were easily damaged in the bonding process prior to lap and polish because of the particular device structure, i.e., air bridges being the highest point of the wafer and only a small number of air bridges on the wafer. To protect the air bridge a patterned photoresist layer was applied before the wafer was bonded to a carrier. .

  3. The History of Static Test and Air Force Structures Testing

    DTIC Science & Technology

    1979-06-01

    incremental loads were being appllied according to the spanwise and chordwise requirements. Once that load increent was in place, the structure was then loaded...Programming of this equipment was accomplished with a language called FOCAL, then BASIC and finally FORTRAN with aisembly language handlers. it took...programs. Software was custort tailored and written in Control Data Corporation 1604 computer assembly language . Air Force efforts to improve the

  4. Structural optimization of 3D porous electrodes for high-rate performance lithium ion batteries.

    PubMed

    Ye, Jianchao; Baumgaertel, Andreas C; Wang, Y Morris; Biener, Juergen; Biener, Monika M

    2015-02-24

    Much progress has recently been made in the development of active materials, electrode morphologies and electrolytes for lithium ion batteries. Well-defined studies on size effects of the three-dimensional (3D) electrode architecture, however, remain to be rare due to the lack of suitable material platforms where the critical length scales (such as pore size and thickness of the active material) can be freely and deterministically adjusted over a wide range without affecting the overall 3D morphology of the electrode. Here, we report on a systematic study on length scale effects on the electrochemical performance of model 3D np-Au/TiO2 core/shell electrodes. Bulk nanoporous gold provides deterministic control over the pore size and is used as a monolithic metallic scaffold and current collector. Extremely uniform and conformal TiO2 films of controlled thickness were deposited on the current collector by employing atomic layer deposition (ALD). Our experiments demonstrate profound performance improvements by matching the Li(+) diffusivity in the electrolyte and the solid state through adjusting pore size and thickness of the active coating which, for 200 μm thick porous electrodes, requires the presence of 100 nm pores. Decreasing the thickness of the TiO2 coating generally improves the power performance of the electrode by reducing the Li(+) diffusion pathway, enhancing the Li(+) solid solubility, and minimizing the voltage drop across the electrode/electrolyte interface. With the use of the optimized electrode morphology, supercapacitor-like power performance with lithium-ion-battery energy densities was realized. Our results provide the much-needed fundamental insight for the rational design of the 3D architecture of lithium ion battery electrodes with improved power performance.

  5. On-chip lithium cells for electrical and structural characterization of single nanowire electrodes

    NASA Astrophysics Data System (ADS)

    Subramanian, A.; Hudak, N. S.; Huang, J. Y.; Zhan, Y.; Lou, J.; Sullivan, J. P.

    2014-07-01

    We present a transmission electron microscopy (TEM)-compatible, hybrid nanomachined, on-chip construct for probing the structural and electrical changes in individual nanowire electrodes during lithium insertion. We have assembled arrays of individual β-phase manganese dioxide (β-MnO2) nanowires (NWs), which are employed as a model material system, into functional electrochemical cells through a combination of bottom-up (dielectrophoresis) and top-down (silicon nanomachining) unit processes. The on-chip NWs are electrochemically lithiated inside a helium-filled glovebox and their electrical conductivity is studied as a function of incremental lithium loading during initial lithiation. We observe a dramatic reduction in NW conductivity (on the order of two to three orders in magnitude), which is not reversed when the lithium is extracted from the nanoelectrode. This conductivity change is attributed to an increase in lattice disorder within the material, which is observed from TEM images of the lithiated NWs. Furthermore, electron energy loss spectroscopy (EELS) was employed to confirm the reduction in valence state of manganese, which occurs due to the transformation of MnO2 to LixMnO2.

  6. Multi-line triggering and interdigitated electrode structure for photoconductive semiconductor switches

    DOEpatents

    Mar, Alan; Zutavern, Fred J.; Loubriel, Guillermo

    2007-02-06

    An improved photoconductive semiconductor switch comprises multiple-line optical triggering of multiple, high-current parallel filaments between the switch electrodes. The switch can also have a multi-gap, interdigitated electrode for the generation of additional parallel filaments. Multi-line triggering can increase the switch lifetime at high currents by increasing the number of current filaments and reducing the current density at the contact electrodes in a controlled manner. Furthermore, the improved switch can mitigate the degradation of switching conditions with increased number of firings of the switch.

  7. The structures of the sintered plaque in the nickel hydroxide electrode

    NASA Technical Reports Server (NTRS)

    Vyas, B.

    1981-01-01

    The various failure mechanisms were identified for the nickel electrode. The nickel sinter is involved in all these failure modes. The first one, chemical attack by carbonate, nitrate or other electrolyte components, involves corrosion of the nickel sinters. The second is the physical mode, which involves swelling of the electrode and physical shifting of the sinter in the electrodes. The third is the mechanical failure mode, and is due to fatigue or to the oxygen pressure that causes deformation or fracture of the sinter.

  8. A corrugated mesoscale structure on electrode-electrolyte interface for enhancing cell performance in anode-supported SOFC

    NASA Astrophysics Data System (ADS)

    Konno, Akio; Iwai, Hiroshi; Saito, Motohiro; Yoshida, Hideo

    For enhancing the power density of a solid oxide fuel cell, mesoscale-structure control of electrode-electrolyte interfaces in an anode-supported cell is proposed. We define 'mesoscale' as a size range of the order of 10-100 μm which is larger than the 'microscale' of electrode particles but smaller than the 'macroscale' of cell geometries. Mesoscale-structure control enlarges the electrode-electrolyte interface, and this enlargement extends an active electrochemical reaction zone where a charge-transfer reaction occurs actively near the interface. A corrugated mesoscale electrolyte was adopted which enlarged the interface structures of both anode and cathode sides. We performed a 2-D numerical simulation, and discussed the effects of such structure not only on the overall performance but also on the detailed distributions of electric potentials, gas concentrations and local electrochemical reaction rate. As a result, it was observed that the corrugated mesoscale structure reduced both activation overpotential and ohmic loss by ion transport, and hence enhanced the power generation performance. When the interface area enlargement factor was 1.73, an enhancement of a power density having a maximum value of 59% was achieved with the mesoscale-corrugated cell rather than with the flat cell.

  9. Lift-Off Free Fabrication Approach for Periodic Structures with Tunable Nano Gaps for Interdigitated Electrode Arrays.

    PubMed

    Partel, Stefan; Dincer, Can; Kasemann, Stephan; Kieninger, Jochen; Edlinger, Johannes; Urban, Gerald

    2016-01-26

    We report a simple, low-cost and lift-off free fabrication approach for periodic structures with adjustable nanometer gaps for interdigitated electrode arrays (IDAs). It combines an initial structure and two deposition process steps; first a dielectric layer is deposited, followed by a metal evaporation. The initial structure can be realized by lithography or any other structuring technique (e.g., nano imprint, hot embossing or injection molding). This method allows the fabrication of nanometer sized gaps and completely eliminates the need for a lift-off process. Different substrate materials like silicon, Pyrex or polymers can be used. The electrode gap is controlled primarily by sputter deposition of the initial structure, and thus, adjustable gaps in the nanometer range can be realized independently of the mask or stamp pattern. Electrochemical characterizations using redox cycling in ferrocenemethanol (FcMeOH) demonstrate signal amplification factors of more than 110 together with collection factors higher than 99%. Furthermore, the correlation between the gap width and the amplification factor was studied to obtain an electrochemical performance assessment of the nano gap electrodes. The results demonstrate an exponential relationship between amplification factor and gap width.

  10. A new high-density (25 electrodes/mm2) penetrating microelectrode array for recording and stimulating sub-millimeter neuroanatomical structures

    NASA Astrophysics Data System (ADS)

    Wark, H. A. C.; Sharma, R.; Mathews, K. S.; Fernandez, E.; Yoo, J.; Christensen, B.; Tresco, P.; Rieth, L.; Solzbacher, F.; Normann, R. A.; Tathireddy, P.

    2013-08-01

    Objective. Among the currently available neural interface devices, there has been a need for a penetrating electrode array with a high electrode-count and high electrode-density (the number of electrodes/mm2) that can be used for electrophysiological studies of sub-millimeter neuroanatomical structures. We have developed such a penetrating microelectrode array with both a high electrode-density (25 electrodes/mm2) and high electrode-count (up to 96 electrodes) for small nervous system structures, based on the existing Utah Slanted Electrode Array (USEA). Such high electrode-density arrays are expected to provide greater access to nerve fibers than the conventionally spaced USEA especially in small diameter nerves. Approach. One concern for such high density microelectrode arrays is that they may cause a nerve crush-type injury upon implantation. We evaluated this possibility during acute (<10 h) in vivo experiments with electrode arrays implanted into small diameter peripheral nerves of anesthetized rats (sciatic nerve) and cats (pudendal nerve). Main results. Successful intrafascicular implantation and viable nerve function was demonstrated via microstimulation, single-unit recordings and histological analysis. Measurements of the electrode impedances and quantified electrode dimensions demonstrated fabrication quality. The results of these experiments show that such high density neural interfaces can be implanted acutely into neural tissue without causing a complete nerve crush injury, while mediating intrafascicular access to fibers in small diameter peripheral nerves. Significance. This new penetrating microelectrode array has characteristics un-matched by other neural interface devices currently available for peripheral nervous system neurophysiological research.

  11. Electrical Characteristics, Electrode Sheath and Contamination Layer Behavior of a Meso-Scale Premixed Methane-Air Flame Under AC/DC Electric Fields

    NASA Astrophysics Data System (ADS)

    Chen, Qi; Yan, Limin; Zhang, Hao; Li, Guoxiu

    2016-05-01

    Electrical characteristics of a nozzle-attached meso-scale premixed methane-air flame under low-frequency AC (0-4300 V, 0-500 Hz) and DC (0-3300 V) electric fields were studied. I-V curves were measured under different experimental conditions to estimate the magnitude of the total current 100-102 μA, the electron density 1015-1016 m-3 and further the power dissipation ≤ 0.7 W in the reaction zone. At the same time, the meso-scale premixed flame conductivity 10-4-10-3 Ω-1·m-1 as a function of voltage and frequency was experimentally obtained and was believed to represent a useful order-of magnitude estimate. Moreover, the influence of the collision sheath relating to Debye length (31-98 μm) and the contamination layer of an active electrode on measurements was discussed, based on the combination of simulation and theoretical analysis. As a result, the electrode sheath dimension was evaluated to less than 0.5 mm, which indicated a complex effect of the collision sheath on the current measurements. The surface contamination effect of an active electrode was further analyzed using the SEM imaging method, which showed elements immigration during the contamination layer formation process. supported by National Natural Science Foundation of China (No. 51376021), and the Fundamental Research Fund for Major Universities (No. 2013JBM079)

  12. Method of forming macro-structured high surface area transparent conductive oxide electrodes

    DOEpatents

    Forman, Arnold J.; Chen, Zhebo; Jaramillo, Thomas F.

    2016-01-05

    A method of forming a high surface area transparent conducting electrode is provided that includes depositing a transparent conducting thin film on a conductive substrate, where the transparent conducting thin film includes transparent conductive particles and a solution-based transparent conducting adhesive layer which serves to coat and bind together the transparent conducting particles, and heat treating the transparent conducting adhesion layer on the conductive substrate, where an increased surface area transparent conducting electrode is formed.

  13. Fiber optic sensors for structural health monitoring of air platforms.

    PubMed

    Guo, Honglei; Xiao, Gaozhi; Mrad, Nezih; Yao, Jianping

    2011-01-01

    Aircraft operators are faced with increasing requirements to extend the service life of air platforms beyond their designed life cycles, resulting in heavy maintenance and inspection burdens as well as economic pressure. Structural health monitoring (SHM) based on advanced sensor technology is potentially a cost-effective approach to meet operational requirements, and to reduce maintenance costs. Fiber optic sensor technology is being developed to provide existing and future aircrafts with SHM capability due to its unique superior characteristics. This review paper covers the aerospace SHM requirements and an overview of the fiber optic sensor technologies. In particular, fiber Bragg grating (FBG) sensor technology is evaluated as the most promising tool for load monitoring and damage detection, the two critical SHM aspects of air platforms. At last, recommendations on the implementation and integration of FBG sensors into an SHM system are provided.

  14. Fiber Optic Sensors for Structural Health Monitoring of Air Platforms

    PubMed Central

    Guo, Honglei; Xiao, Gaozhi; Mrad, Nezih; Yao, Jianping

    2011-01-01

    Aircraft operators are faced with increasing requirements to extend the service life of air platforms beyond their designed life cycles, resulting in heavy maintenance and inspection burdens as well as economic pressure. Structural health monitoring (SHM) based on advanced sensor technology is potentially a cost-effective approach to meet operational requirements, and to reduce maintenance costs. Fiber optic sensor technology is being developed to provide existing and future aircrafts with SHM capability due to its unique superior characteristics. This review paper covers the aerospace SHM requirements and an overview of the fiber optic sensor technologies. In particular, fiber Bragg grating (FBG) sensor technology is evaluated as the most promising tool for load monitoring and damage detection, the two critical SHM aspects of air platforms. At last, recommendations on the implementation and integration of FBG sensors into an SHM system are provided. PMID:22163816

  15. 78 FR 40446 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-05

    ... of the Secretary Meeting of the National Commission on the Structure of the Air Force AGENCY... National Commission on the Structure of the Air Force (``the Commission'') will take place. DATES: Date of... Moore, Designated Federal Officer, National Commission on the Structure of the Air Force, 1950...

  16. 78 FR 43865 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-22

    ... of the Secretary Meeting of the National Commission on the Structure of the Air Force AGENCY... National Commission on the Structure of the Air Force (``the Commission'') will take place. DATES: Date of... Commission on the Structure of the Air Force, 1950 Defense Pentagon, Room 3A874, Washington, DC...

  17. 78 FR 56219 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-12

    ... of the Secretary Meeting of the National Commission on the Structure of the Air Force AGENCY... meeting of the National Commission on the Structure of the Air Force (``the Commission'') will take place..., Designated Federal Officer, National Commission on the Structure of the Air Force, 1950 Defense...

  18. 78 FR 40730 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-08

    ... of the Secretary Meeting of the National Commission on the Structure of the Air Force AGENCY... National Commission on the Structure of the Air Force (``the Commission'') will take place. DATES: Date of..., National Commission on the Structure of the Air Force, 1950 Defense Pentagon, Room 3A874, Washington,...

  19. 78 FR 61342 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-03

    ... of the Secretary Meeting of the National Commission on the Structure of the Air Force AGENCY... meeting of the National Commission on the Structure of the Air Force (``the Commission'') will take place... Officer, National Commission on the Structure of the Air Force, 1950 Defense Pentagon, Room...

  20. 78 FR 51175 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-20

    ... of the Secretary Meeting of the National Commission on the Structure of the Air Force AGENCY... National Commission on the Structure of the Air Force (``the Commission'') will take place. DATES: Date of..., National Commission on the Structure of the Air Force, 1950 Defense Pentagon, Room 3A874, Washington,...

  1. 78 FR 46329 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-31

    ... Office of the Secretary Meeting of the National Commission on the Structure of the Air Force AGENCY... National Commission on the Structure of the Air Force (``the Commission'') will take place. DATES: Date of..., National Commission on the Structure of the Air Force, 1950 Defense Pentagon, Room 3A874, Washington,...

  2. 78 FR 53133 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-28

    ... of the Secretary Meeting of the National Commission on the Structure of the Air Force AGENCY... National Commission on the Structure of the Air Force (``the Commission'') will take place. DATES: Date of..., Designated Federal Officer, National Commission on the Structure of the Air Force, 1950 Defense...

  3. 78 FR 46928 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-08-02

    ... of the Secretary Meeting of the National Commission on the Structure of the Air Force AGENCY... National Commission on the Structure of the Air Force (``the Commission'') will take place. DATES: Date of... Federal Officer, National Commission on the Structure of the Air Force, 1950 Defense Pentagon, Room...

  4. 78 FR 33394 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-04

    ... of the Secretary Meeting of the National Commission on the Structure of the Air Force AGENCY... National Commission on the Structure of the Air Force (``the Commission'') will take place. DATES: Date of... the Structure of the Air Force, 1950 Defense Pentagon, Room 3A874, Washington, DC 20301-1950....

  5. 78 FR 58525 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-24

    ... of the Secretary Meeting of the National Commission on the Structure of the Air Force AGENCY... closed meeting of the National Commission on the Structure of the Air Force (``the Commission'') will..., Designated Federal Officer, National Commission on the Structure of the Air Force, 1950 Defense...

  6. 78 FR 22852 - Establishment of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-04-17

    ... of the Secretary Establishment of the National Commission on the Structure of the Air Force AGENCY... the charter for the National Commission on the Structure of the Air Force (hereinafter referred to as... study. In considering the structure of the Air Force, the Commission shall give particular...

  7. 78 FR 61343 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-03

    ... of the Secretary Meeting of the National Commission on the Structure of the Air Force AGENCY... Commission on the Structure of the Air Force (``the Commission'') will take place. DATES: Date of Open..., National Commission on the Structure of the Air Force, 1950 Defense Pentagon, Room 3A874, Washington,...

  8. A top-down approach for fabricating free-standing bio-carbon supercapacitor electrodes with a hierarchical structure

    PubMed Central

    Li, Yingzhi; Zhang, Qinghua; Zhang, Junxian; Jin, Lei; Zhao, Xin; Xu, Ting

    2015-01-01

    Biomass has delicate hierarchical structures, which inspired us to develop a cost-effective route to prepare electrode materials with rational nanostructures for use in high-performance storage devices. Here, we demonstrate a novel top-down approach for fabricating bio-carbon materials with stable structures and excellent diffusion pathways; this approach is based on carbonization with controlled chemical activation. The developed free-standing bio-carbon electrode exhibits a high specific capacitance of 204 F g−1 at 1 A g−1; good rate capability, as indicated by the residual initial capacitance of 85.5% at 10 A g−1; and a long cycle life. These performance characteristics are attributed to the outstanding hierarchical structures of the electrode material. Appropriate carbonization conditions enable the bio-carbon materials to inherit the inherent hierarchical texture of the original biomass, thereby facilitating effective channels for fast ion transfer. The macropores and mesopores that result from chemical activation significantly increase the specific surface area and also play the role of temporary ion-buffering reservoirs, further shortening the ionic diffusion distance. PMID:26394834

  9. A top-down approach for fabricating free-standing bio-carbon supercapacitor electrodes with a hierarchical structure.

    PubMed

    Li, Yingzhi; Zhang, Qinghua; Zhang, Junxian; Jin, Lei; Zhao, Xin; Xu, Ting

    2015-09-23

    Biomass has delicate hierarchical structures, which inspired us to develop a cost-effective route to prepare electrode materials with rational nanostructures for use in high-performance storage devices. Here, we demonstrate a novel top-down approach for fabricating bio-carbon materials with stable structures and excellent diffusion pathways; this approach is based on carbonization with controlled chemical activation. The developed free-standing bio-carbon electrode exhibits a high specific capacitance of 204 F g(-1) at 1 A g(-1); good rate capability, as indicated by the residual initial capacitance of 85.5% at 10 A g(-1); and a long cycle life. These performance characteristics are attributed to the outstanding hierarchical structures of the electrode material. Appropriate carbonization conditions enable the bio-carbon materials to inherit the inherent hierarchical texture of the original biomass, thereby facilitating effective channels for fast ion transfer. The macropores and mesopores that result from chemical activation significantly increase the specific surface area and also play the role of temporary ion-buffering reservoirs, further shortening the ionic diffusion distance.

  10. Simulation study on structure of water in aqueous solutions confined between graphene electrodes under very high applied electric field

    NASA Astrophysics Data System (ADS)

    Leuty, Gary; Tsige, Mesfin; Talapatra, Saikat

    2011-03-01

    Arising from questions regarding electric double-layer capacitors utilizing graphene electrodes and aqueous electrolyte (KOH solution), atomistic MD simulations of electrolyte confined between graphene electrodes were performed to understand the behavior of electrolyte as a function of electric field strength and solution concentration, from pure water to 6M KOH. It was noted that the strength of the electric field had a demonstrable effect on the structure of pure water between the electrodes (as has previously been seen in highly confined multilayer water systems), creating regularly spaced channels and densely packed sheets of highly ordered molecules. We also saw a clear effect due to the presence of electrolyte ions and their separation from the water due to the action of the field; different field strengths appear to greatly alter the distribution of ions, which in turn affects the structure and ordering of the water. Time dependence in the strength of the electric field was also studied to determine what effect, if any, it has on induced structure. Authors gratefully acknowledge support from the ACS Petroleum Research Fund and the National Science Foundation.

  11. Electronic Structure at Electrode/Electrolyte Interfaces in Magnesium based Batteries

    NASA Astrophysics Data System (ADS)

    Balachandran, Janakiraman; Siegel, Donald

    2015-03-01

    Magnesium is a promising multivalent element for use in next generation electrochemical energy storage systems. However, a wide range of challenges such as low coulombic efficiency, low/varying capacity and cyclability need to be resolved in order to realize Mg based batteries. Many of these issues can be related to interfacial phenomena between the Mg anode and common electrolytes. Ab-initio based computational models of these interfaces can provide insights on the interfacial interactions that can be difficult to probe experimentally. In this work we present ab-initio computations of common electrolyte solvents (THF, DME) in contact with two model electrode surfaces namely -- (i) an ``SEI-free'' electrode based on Mg metal and, (ii) a ``passivated'' electrode consisting of MgO. We perform GW calculations to predict the reorganization of the molecular orbitals (HOMO/LUMO) upon contact with the these surfaces and their alignment with respect to the Fermi energy of the electrodes. These computations are in turn compared with more efficient GGA (PBE) & Hybrid (HSE) functional calculations. The results obtained from these computations enable us to qualitatively describe the stability of these solvent molecules at electrode-electrolyte interfaces

  12. Structural design of flexible Au electrode to enable shape memory polymer for electrical actuation

    NASA Astrophysics Data System (ADS)

    Lu, Haibao; Lei, Ming; Zhao, Chao; Xu, Ben; Leng, Jinsong; Fu, Y. Q.

    2015-04-01

    An effective resistive Joule heating approach was conducted to improve the electrical actuation and shape-recovery performance of a shape memory polymer (SMP) nanocomposite. Two types of gold (Au) film patterns were deposited to be used as electrodes to drive thermal-responsive SMPs and achieve a uniform temperature distribution during electro-activated shape recovery. Furthermore, the sensing capability of the Au electrode to both mechanical and thermal stimuli applied to the SMP nanocomposite was experimentally investigated and theoretically analyzed. It was found that the change in the electrical resistance of the Au electrode could be used as an indication of shape-recovery performance. The linear response of the electrical resistance to strain was identified mainly due to the opening/closing of microcracks and their propagations in the Au electrodes during out-of-plane deformations. With an increment of thermomechanical bending cycles, the electrical resistance was increased exponentially, but it returned back to the original reading when the SMP nanocomposite returned back to its permanent shape. Finally, the flexible Au electrode enabled the actuation of the SMP nanocomposite under an electric voltage of 13.4 V, with an improved shape-recovery performance and temperature distribution.

  13. Reliable metal deposition into TiO(2) nanotubes for leakage-free interdigitated electrode structures and use as a memristive electrode.

    PubMed

    Liu, Ning; Lee, Kiyoung; Schmuki, Patrik

    2013-11-18

    Nearly 100 % filling of TiO2 nanotubes with metals, including Ag, Cu, Au, and Pt, was achieved by defect-sealing treatment at the bottom of the nanotubes, followed by metal deposition using nuclei formation/coalescence. The resulting short-circuit-free interdigitated electrode configurations can, for example, be used to fabricate memristive electrodes.

  14. Bridging Oriented Copper Nanowire-Graphene Composites for Solution-Processable, Annealing-Free, and Air-Stable Flexible Electrodes.

    PubMed

    Zhang, Wang; Yin, Zhenxing; Chun, Alvin; Yoo, Jeeyoung; Kim, Youn Sang; Piao, Yuanzhe

    2016-01-27

    One-dimensional flexible metallic nanowires (NWs) are of considerable interest for next-generation wearable devices. The unavoidable challenge for a wearable electrode is the assurance of high conductivity, flexibility, and durability with economically feasible materials and simple manufacturing processes. Here, we use a straightforward solvothermal method to prepare a flexible conductive material that contains reduced graphene oxide (RGO) nanosheets bridging oriented copper NWs. The GO-assistance route can successfully meet the criteria listed above and help the composite films maintain high conductivity and durable flexibility without any extra treatment, such as annealing or acid processes. The composite film exhibits a high electrical performance (0.808 Ω·sq(-1)) without considerable change over 30 days under ambient conditions. Moreover, the Cu NW-RGO composites can be deposited on polyester cloth as a lightweight wearable electrode with high durability and simple processability and are very promising for a wide variety of electronic devices.

  15. Electrode electrolyte interlayers containing cerium oxide for electrochemical fuel cells

    DOEpatents

    Borglum, Brian P.; Bessette, Norman F.

    2000-01-01

    An electrochemical cell is made having a porous fuel electrode (16) and a porous air electrode (13), with solid oxide electrolyte (15) therebetween, where the air electrode surface opposing the electrolyte has a separate, attached, dense, continuous layer (14) of a material containing cerium oxide, and where electrolyte (16) contacts the continuous oxide layer (14), without contacting the air electrode (13).

  16. A novel high capacity positive electrode material with tunnel-type structure for aqueous sodium-ion batteries

    SciTech Connect

    Wang, Yuesheng; Mu, Linqin; Liu, Jue; Yang, Zhenzhong; Yu, Xiqian; Gu, Lin; Hu, Yong -Sheng; Li, Hong; Yang, Xiao -Qing; Chen, Liquan; Huang, Xuejie

    2015-08-06

    In this study, aqueous sodium-ion batteries have shown desired properties of high safety characteristics and low-cost for large-scale energy storage applications such as smart grid, because of the abundant sodium resources as well as the inherently safer aqueous electrolytes. Among various Na insertion electrode materials, tunnel-type Na0.44MnO2 has been widely investigated as a positive electrode for aqueous sodium-ion batteries. However, the low achievable capacity hinders its practical applications. Here we report a novel sodium rich tunnel-type positive material with a nominal composition of Na0.66[Mn0.66Ti0.34]O2. The tunnel-type structure of Na0.44MnO2 obtained for this compound was confirmed by XRD and atomic-scale STEM/EELS. When cycled as positive electrode in full cells using NaTi2(PO4)3/C as negative electrode in 1M Na2SO4 aqueous electrolyte, this material shows the highest capacity of 76 mAh g-1 among the Na insertion oxides with an average operating voltage of 1.2 V at a current rate of 2C. These results demonstrate that Na0.66[Mn0.66Ti0.34]O2 is a promising positive electrode material for rechargeable aqueous sodium-ion batteries.

  17. Microbial community structure of different electrode materials in constructed wetland incorporating microbial fuel cell.

    PubMed

    Wang, Junfeng; Song, Xinshan; Wang, Yuhui; Abayneh, Befkadu; Ding, Yi; Yan, Denghua; Bai, Junhong

    2016-12-01

    The microbial fuel cell coupled with constructed wetland (CW-MFC) microcosms were operated under fed-batch mode for evaluating the effect of electrode materials on bioelectricity generation and microbial community composition. Experimental results indicated that the bioenergy output in CW-MFC increased with the substrate concentration; maximum average voltage (177mV) was observed in CW-MFC with carbon fiber felt (CFF). In addition, the four different materials resulted in the formation of significantly different microbial community distribution around the anode electrode. The relative abundance of Proteobacteria in CFF and foamed nickel (FN) was significantly higher than that in stainless steel mesh (SSM) and graphite rod (GR) samples. Notably, the findings indicate that CW-MFC utilizing FN anode electrode could apparently improve relative abundance of Dechloromonas, which has been regarded as a denitrifying and phosphate accumulating microorganism.

  18. Fabrication and modeling of electrochemical double-layer capacitors using carbon nano-onion electrode structures

    NASA Astrophysics Data System (ADS)

    Parigi, Fabio

    Electrochemical capacitors or ultracapacitors (UCs) that are commercially available today overcome battery limitations in terms of charging time (from tens of minutes to seconds) and limited lifetime (from a few thousand cycles up to more than one million) but still lack specific energy and energy density (2-5% of a lithium ion battery). The latest innovations in carbon nanomaterials, such as carbon nanotubes as an active electrode material for UCs, can provide up to five times as much energy and deliver up to seven times more power than today's activated carbon electrodes. Further improvements in UC power density have been achieved by using state-of-the-art carbon nano-onions (CNOs) for ultracapacitor electrodes. CNO UCs could exhibit up to five times the power density of single-wall CNT UCs and could substantially contribute to reducing the size of an energy storage system as well as the volume and weight, thus improving device performance. This dissertation describes the fabrication of CNO electrodes as part of an UC device, the measurement and analysis of the new electrode's performance as an energy storage component, and development of a new circuit model that accurately describes the CNO UC electrical behavior. The novel model is based on the impedance spectra of CNO UCs and cyclic voltammetry measurements. Further, the model was validated using experimental data and simulation. My original contributions are the fabrication process for reliable and repeatable electrode fabrication and the modeling of a carbon nano-onion ultracapacitor. The carbon nano-onion ultracapacitor model, composed of a resistor, an inductor, a capacitor (RLC), and a constant phase element (CPE), was developed along with a parameter extraction procedure for the benefit of other users. The new model developed, proved to be more accurate than previously reported UC models.

  19. NiCd battery electrodes, C-150

    NASA Technical Reports Server (NTRS)

    Holleck, G.; Turchan, M.; Hopkins, J.

    1972-01-01

    Electrodes for a nongassing negative limited nickel-cadmium cell are discussed. The key element is the development of cadmium electrodes with high hydrogen overvoltage. For this, the following electrode structures were manufactured and their physical and electrochemical characteristics were evaluated: (1) silver-sinter-based Cd electrodes, (2) Teflon-bonded Cd electrodes, (3) electrodeposited Cd sponge, and (4) Cd-sinter structures.

  20. Recirculating electric air filter

    DOEpatents

    Bergman, Werner

    1986-01-01

    An electric air filter cartridge has a cylindrical inner high voltage eleode, a layer of filter material, and an outer ground electrode formed of a plurality of segments moveably connected together. The outer electrode can be easily opened to remove or insert filter material. Air flows through the two electrodes and the filter material and is exhausted from the center of the inner electrode.

  1. Zinc oxide modified with benzylphosphonic acids as transparent electrodes in regular and inverted organic solar cell structures

    SciTech Connect

    Lange, Ilja; Reiter, Sina; Kniepert, Juliane; Piersimoni, Fortunato; Brenner, Thomas; Neher, Dieter; Pätzel, Michael; Hildebrandt, Jana; Hecht, Stefan

    2015-03-16

    An approach is presented to modify the work function of solution-processed sol-gel derived zinc oxide (ZnO) over an exceptionally wide range of more than 2.3 eV. This approach relies on the formation of dense and homogeneous self-assembled monolayers based on phosphonic acids with different dipole moments. This allows us to apply ZnO as charge selective bottom electrodes in either regular or inverted solar cell structures, using poly(3-hexylthiophene):phenyl-C71-butyric acid methyl ester as the active layer. These devices compete with or even surpass the performance of the reference on indium tin oxide/poly(3,4-ethylenedioxythiophene) polystyrene sulfonate. Our findings highlight the potential of properly modified ZnO as electron or hole extracting electrodes in hybrid optoelectronic devices.

  2. Mesoscale effects in electrochemical conversion: coupling of chemistry to atomic- and nanoscale structure in iron-based electrodes.

    PubMed

    Wiaderek, Kamila M; Borkiewicz, Olaf J; Pereira, Nathalie; Ilavsky, Jan; Amatucci, Glenn G; Chupas, Peter J; Chapman, Karena W

    2014-04-30

    The complex coupling of atomic, chemical, and electronic transformations across multiple length scales underlies the performance of electrochemical energy storage devices. Here, the coupling of chemistry with atomic- and nanoscale structure in iron conversion electrodes is resolved by combining pair distribution function (PDF) and small-angle X-ray scattering (SAXS) analysis for a series of Fe fluorides, oxyfluorides, and oxides. The data show that the anion chemistry of the initial electrode influences the abundance of atomic defects in the Fe atomic lattice. This, in turn, is linked to different atom mobilities and propensity for particle growth. Competitive nanoparticle growth in mixed anion systems contributes to a distinct nanostructure, without the interconnected metallic nanoparticles formed for single anion systems.

  3. 78 FR 59343 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-09-26

    ... of the Secretary Meeting of the National Commission on the Structure of the Air Force AGENCY... meeting of the National Commission on the Structure of the Air Force (``the Commission'') will take place... the Air Force, 1950 Defense Pentagon, Room 3A874, Washington, DC 20301-1950. Email:...

  4. 78 FR 78943 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-12-27

    ... of the Secretary Meeting of the National Commission on the Structure of the Air Force AGENCY... the National Commission on the Structure of the Air Force (``the Commission''). DATES: Date of Closed... the Air Force, 1950 Defense Pentagon, Room 3A874, Washington, DC 20301-1950. Email:...

  5. 78 FR 37798 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-24

    ... of the Secretary Meeting of the National Commission on the Structure of the Air Force AGENCY... National Commission on the Structure of the Air Force (``the Commission'') will take place. DATES: Date of... the Air Force, 1950 Defense Pentagon, Room 3A874, Washington, DC 20301-1950. Email:...

  6. 78 FR 36751 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-19

    ... of the Secretary Meeting of the National Commission on the Structure of the Air Force AGENCY... National Commission on the Structure of the Air Force (``the Commission'') will take place. DATES: Date of... the Air Force, 1950 Defense Pentagon, Room 3A874, Washington, DC 20301-1950. Email:...

  7. Magneto-electrochemical recovery of diluted metals using three-dimensionally structured electrodes

    NASA Astrophysics Data System (ADS)

    Fernández, Dámaris; Romeral, Luis; Lyons, Michael E. G.

    2015-04-01

    In a typical metal recovery process, where highly purified metals are obtained from a concentrated electrolyte, usually the cathodic electrodes are planar and can be described mainly as bi-dimensional. This leads to a low space-time yield and low normalized space velocity with an impact on production rates. New requirements of low-energy consumption yet intensive production factories impose the need to adequate electrodes in order to comply. Furthermore, a reduction in the number of steps required to achieve a product would be ideal. This suggests that direct electro-precipitation of metals contained in diluted electrolytes would be in principle a desirable technique to implement. However, the less concentrated the solution, the higher the IR drop becomes, making the process more energy-consuming and current efficiency strongly decays. Good potential alternatives arise from three-dimensionally designed electrodes in the form of mesh, porous or fluidized beds, for instance, and several examples are well known in literature. Nevertheless, current efficiency can still be a problem in the more diluted electrolytes. Furthermore, the anodic electrode, where the counter reaction takes place, plays also an important role in determining the current efficiency of the overall process. In this case, the liquid-to-gas phase transition implies that the electrodes get a strong gas shield that increases the IR drop. Whereas shifting from bi-dimensional to three-dimensional electrodes could provide an alternative for achieving better performances, it is still far from the expected targets. Therefore alternative or complementary techniques to improve efficiency are required. It is well known that magnetic fields coupled with electric fields enhance mass transport via de Lorentz and other forces. In this work, the applications and properties of three-dimensional arrays subject to magnetic field interactions are examined and compared with the traditional bi-dimensional electrodes

  8. Capacitive de-ionization electrode

    DOEpatents

    Daily, III, William D.

    2013-03-19

    An electrode "cell" for use in a capacitive deionization (CDI) reactor consists of the electrode support structure, a non-reactive conductive material, the electrode accompaniment or substrate and a flow through screen/separator. These "layers" are repeated and the electrodes are sealed together with gaskets between two end plates to create stacked sets of alternating anode and cathode electrodes in the CDI reactor.

  9. Effect of pH in a Pd-based ethanol membraneless air breathing nanofluidic fuel cell with flow-through electrodes

    NASA Astrophysics Data System (ADS)

    López-Rico, C. A.; Galindo-de-la-Rosa, J.; Ledesma-García, J.; Arriaga, L. G.; Guerra-Balcázar, M.; Arjona, N.

    2015-12-01

    In this work, a nanofluidic fuel cell (NFC) in which streams flow through electrodes was used to investigate the role of pH in the cell performance using ethanol as fuel and two Pd nanoparticles as electrocatalysts: one commercially available (Pd/C from ETEK) and other synthesized using ionic liquids (Pd/C IL). The cell performances for both electrocatalysts in acid/acid (anodic/cathodic) streams were of 18.05 and 9.55 mW cm-2 for Pd/C ETEK and Pd/C IL. In alkaline/alkaline streams, decrease to 15.94 mW cm-2 for Pd/C ETEK and increase to 15.37 mW cm-2 for Pd/C IL. In alkaline/acidic streams both electrocatalysts showed similar cell voltages (up to 1 V); meanwhile power densities were of 87.6 and 99.4 mW cm-2 for Pd/C ETEK and Pd/C IL. The raise in cell performance can be related to a decrease in activation losses, the combined used of alkaline and acidic streams and these high values compared with flow-over fuel cells can be related to the enhancement of the cathodic mass transport by using three dimensional porous electrodes and two sources of oxygen: from air and from a saturated solution.

  10. Surface potential distribution and airflow performance of different air-exposed electrode plasma actuators at different alternating current/direct current voltages

    SciTech Connect

    Yang, Liang; Yan, Hui-Jie; Qi, Xiao-Hua; Hua, Yue; Ren, Chun-Sheng

    2015-04-15

    Asymmetric surface dielectric barrier discharge (SDBD) plasma actuators have been intensely studied for a number of years due to their potential applications for aerodynamic control. In this paper, four types of actuators with different configurations of exposed electrode are proposed. The SDBD actuators investigated are driven by dual-power supply, referred to as a fixed AC high voltage and an adjustable DC bias. The effects of the electrode structures on the dielectric surface potential distribution, the electric wind velocity, and the mean thrust production are studied, and the dominative factors of airflow acceleration behavior are revealed. The results have shown that the actions of the SDBD actuator are mainly dependent on the geometry of the exposed electrode. Besides, the surface potential distribution can effectively affect the airflow acceleration behavior. With the application of an appropriate additional DC bias, the surface potential will be modified. As a result, the performance of the electric wind produced by a single SDBD can be significantly improved. In addition, the work also illustrates that the actuators with more negative surface potential present better mechanical performance.

  11. Coupled modeling of water transport and air-droplet interaction in the electrode of a proton exchange membrane fuel cell

    NASA Astrophysics Data System (ADS)

    Esposito, Angelo; Pianese, Cesare; Guezennec, Yann G.

    In this work, an accurate and computationally fast model for liquid water transport within a proton exchange membrane fuel cell (PEMFC) electrode is developed by lumping the space-dependence of the relevant variables. Capillarity is considered as the main transport mechanism within the gas diffusion layer (GDL). The novelty of the model lies in the coupled simulation of the water transport at the interface between gas diffusion layer and gas flow channel (GFC). This is achieved with a phenomenological description of the process that allows its simulation with relative simplicity. Moreover, a detailed two-dimensional visualization of such interface is achieved via geometric simulation of water droplets formation, growth, coalescence and detachment on the surface of the GDL. The model is useful for optimization analysis oriented to both PEMFC design and balance of plant. Furthermore, the accomplishment of reduced computational time and good accuracy makes the model suitable for control strategy implementation to ensure PEM fuel cells operation within optimal electrode water content.

  12. Synthesis and characterization of carbon black/manganese oxide air cathodes for zinc-air batteries: Effects of the crystalline structure of manganese oxides

    NASA Astrophysics Data System (ADS)

    Li, Po-Chieh; Hu, Chi-Chang; Noda, Hiroyuki; Habazaki, Hiroki

    2015-12-01

    Manganese oxides (MnOx) in α-, β-, γ-, δ-MnO2 phases, Mn3O4, Mn2O3, and MnOOH are synthesized for systematically comparing their electrocatalytic activity of the oxygen reduction reaction (ORR) in the Zn-air battery application. The optimal MnOx/XC-72 mass ratio for the ORR is equal to 1 and the oxide crystalline structure effect on the ORR is compared. The order of composites with respect to decreasing the ORR activity is: α-MnO2/XC-72 > γ-MnO2/XC-72 > β-MnO2/XC-72 > δ-MnO2/XC-72 > Mn2O3/XC-72 > Mn3O4/XC-72 > MnOOH/XC-72. The textural properties of MnOx are investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), N2 adsorption/desorption isotherms with Brunauer-Emmett-Teller (BET) analysis, X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Electrochemical studies include linear sweep voltammetry (LSV), rotating ring-disk electrode (RRDE) voltammetry, and the full-cell discharge test. The discharge peak power density of Zn-air batteries varies from 61.5 mW cm-2 (α-MnO2/XC-72) to 47.1 mW cm-2 (Mn3O4/XC-72). The maximum peak power density is 102 mW cm-2 for the Zn-air battery with an air cathode containing α-MnO2/XC-72 under an oxygen atmosphere when the carbon paper is 10AA. The specific capacity of all full-cell tests is higher than 750 mAh g-1 at all discharge current densities.

  13. A solvent-free microbial-activated air cathode battery paper platform made with pencil-traced graphite electrodes.

    PubMed

    Lee, Seung Ho; Ban, Ju Yeon; Oh, Chung-Hun; Park, Hun-Kuk; Choi, Samjin

    2016-06-23

    We present the fabrication of an ultra-low cost, disposable, solvent-free air cathode all-paper microbial fuel cell (MFC) that does not utilize any chemical treatments. The anode and cathode were fabricated by depositing graphite particles by drawing them on paper with a pencil (four strokes). Hydrophobic parchment paper was used as a proton exchange membrane (PEM) to allow only H(+) to pass. Air cathode MFC technology, where O2 was used as an electron acceptor, was implemented on the paper platform. The bioelectric current was generated by an electrochemical process involving the redox couple of microbial-activated extracellular electron transferred electrons, PEM-passed H(+), and O2 in the cathode. A fully micro-integrated pencil-traced MFC showed a fast start-time, producing current within 10 s after injection of bacterial cells. A single miniaturized all-paper air cathode MFC generated a maximum potential of 300 mV and a maximum current of 11 μA during 100 min after a single injection of Shewanella oneidensis. The micro-fabricated solvent-free air cathode all-paper MFC generated a power of 2,270 nW (5.68 mW/m(2)). The proposed solvent-free air cathode paper-based MFC device could be used for environmentally-friendly energy storage as well as in single-use medical power supplies that use organic matter.

  14. A solvent-free microbial-activated air cathode battery paper platform made with pencil-traced graphite electrodes

    PubMed Central

    Lee, Seung Ho; Ban, Ju Yeon; Oh, Chung-Hun; Park, Hun-Kuk; Choi, Samjin

    2016-01-01

    We present the fabrication of an ultra-low cost, disposable, solvent-free air cathode all-paper microbial fuel cell (MFC) that does not utilize any chemical treatments. The anode and cathode were fabricated by depositing graphite particles by drawing them on paper with a pencil (four strokes). Hydrophobic parchment paper was used as a proton exchange membrane (PEM) to allow only H+ to pass. Air cathode MFC technology, where O2 was used as an electron acceptor, was implemented on the paper platform. The bioelectric current was generated by an electrochemical process involving the redox couple of microbial-activated extracellular electron transferred electrons, PEM-passed H+, and O2 in the cathode. A fully micro-integrated pencil-traced MFC showed a fast start-time, producing current within 10 s after injection of bacterial cells. A single miniaturized all-paper air cathode MFC generated a maximum potential of 300 mV and a maximum current of 11 μA during 100 min after a single injection of Shewanella oneidensis. The micro-fabricated solvent-free air cathode all-paper MFC generated a power of 2,270 nW (5.68 mW/m2). The proposed solvent-free air cathode paper-based MFC device could be used for environmentally-friendly energy storage as well as in single-use medical power supplies that use organic matter. PMID:27333815

  15. A solvent-free microbial-activated air cathode battery paper platform made with pencil-traced graphite electrodes

    NASA Astrophysics Data System (ADS)

    Lee, Seung Ho; Ban, Ju Yeon; Oh, Chung-Hun; Park, Hun-Kuk; Choi, Samjin

    2016-06-01

    We present the fabrication of an ultra-low cost, disposable, solvent-free air cathode all-paper microbial fuel cell (MFC) that does not utilize any chemical treatments. The anode and cathode were fabricated by depositing graphite particles by drawing them on paper with a pencil (four strokes). Hydrophobic parchment paper was used as a proton exchange membrane (PEM) to allow only H+ to pass. Air cathode MFC technology, where O2 was used as an electron acceptor, was implemented on the paper platform. The bioelectric current was generated by an electrochemical process involving the redox couple of microbial-activated extracellular electron transferred electrons, PEM-passed H+, and O2 in the cathode. A fully micro-integrated pencil-traced MFC showed a fast start-time, producing current within 10 s after injection of bacterial cells. A single miniaturized all-paper air cathode MFC generated a maximum potential of 300 mV and a maximum current of 11 μA during 100 min after a single injection of Shewanella oneidensis. The micro-fabricated solvent-free air cathode all-paper MFC generated a power of 2,270 nW (5.68 mW/m2). The proposed solvent-free air cathode paper-based MFC device could be used for environmentally-friendly energy storage as well as in single-use medical power supplies that use organic matter.

  16. Electrode films of porous agarose: The effects of physical structure on electron transport processes. [Impregnated with Nafion; immobilized electroactive species

    SciTech Connect

    Moran, K.D.

    1988-02-01

    Potential use of chemically modified electrodes in electrocatalysis has stimulated interest in creation and characterization of electrode films for reagent immobilization. We have created two highly porous electrocatalyst support matrices, with high rates of electron transport. Both are based on immobilization of reagents in agarose gel. In one case, Nafion was impregnated into agarose gel films. Diffusion of methyl viologen in Nafionagarose matrices are higher than in Nafion. In Nafion, the diffusion coefficient decreases with increasing methyl viologen concentration, while in Nafionagarose, the opposite dependence is observed. The faster rate of electron transport in Nafionagarose films is related to the heterogeneous structure and the coupling of the diffusion pathways. In the second application of agarose gels as an electrode coating material, agarose hydroxyl groups were activated in 1,1'carbonyldiimidazole and subsequently reacted with amine derivatives of electroactive mediators. Electron transport between the electroactive sites in the gel is very rapid (on the order of 10/sup -7/ cm/sup 2/s. Interpreting the data in light of the Dahms-Ruff description of electron transport shows that the rate of electron transport through both ferrocene and viologen derivatized gels is limited by the rate of electron self-exchange of the species. 22 figs., 15 tabs

  17. Effect of structure on current and potential distributions in porous electrode

    NASA Technical Reports Server (NTRS)

    Lanzi, Oscar; Landau, Uziel

    1987-01-01

    Porous electrodes generally contain constricted macropores and localized micropores. The effects of the macropore constrictions on the resistance of a capillary were studied and an analytical model was developed for predicting the current distribution in a constricted macropore which directly includes constriction effects and does not require an empirical tortuosity parameter. The current and concentration distributions in localized micropores were also investigated and it was shown that the microporous area is fully accessible to charge and mass transfer processes. From these analyses it was concluded that the micropores primarily affect the kinetics of the interfacial processes by contributing to the interfacial area, while the macropores impose ohmic and mass transport limitations through the volume of the porous electrode.

  18. AIRE-PHD fingers are structural hubs to maintain the integrity of chromatin-associated interactome.

    PubMed

    Gaetani, Massimiliano; Matafora, Vittoria; Saare, Mario; Spiliotopoulos, Dimitrios; Mollica, Luca; Quilici, Giacomo; Chignola, Francesca; Mannella, Valeria; Zucchelli, Chiara; Peterson, Pärt; Bachi, Angela; Musco, Giovanna

    2012-12-01

    Mutations in autoimmune regulator (AIRE) gene cause autoimmune polyendocrinopathy candidiasis ectodermal dystrophy. AIRE is expressed in thymic medullary epithelial cells, where it promotes the expression of peripheral-tissue antigens to mediate deletional tolerance, thereby preventing self-reactivity. AIRE contains two plant homeodomains (PHDs) which are sites of pathological mutations. AIRE-PHD fingers are important for AIRE transcriptional activity and presumably play a crucial role in the formation of multimeric protein complexes at chromatin level which ultimately control immunological tolerance. As a step forward the understanding of AIRE-PHD fingers in normal and pathological conditions, we investigated their structure and used a proteomic SILAC approach to assess the impact of patient mutations targeting AIRE-PHD fingers. Importantly, both AIRE-PHD fingers are structurally independent and mutually non-interacting domains. In contrast to D297A and V301M on AIRE-PHD1, the C446G mutation on AIRE-PHD2 destroys the structural fold, thus causing aberrant AIRE localization and reduction of AIRE target genes activation. Moreover, mutations targeting AIRE-PHD1 affect the formation of a multimeric protein complex at chromatin level. Overall our results reveal the importance of AIRE-PHD domains in the interaction with chromatin-associated nuclear partners and gene regulation confirming the role of PHD fingers as versatile protein interaction hubs for multiple binding events.

  19. A hydrogen peroxide sensor based on Ag nanoparticles electrodeposited on natural nano-structure attapulgite modified glassy carbon electrode.

    PubMed

    Chen, Huihui; Zhang, Zhe; Cai, Dongqing; Zhang, Shengyi; Zhang, Bailin; Tang, Jilin; Wu, Zhengyan

    2011-10-30

    A novel strategy to fabricate hydrogen peroxide (H(2)O(2)) sensor was developed by electrodepositing Ag nanoparticles (NPs) on a glassy carbon electrode modified with natural nano-structure attapulgite (ATP). The result of electrochemical experiments showed that such constructed sensor had a favorable catalytic ability to reduce H(2)O(2). The good catalytic activity of the sensor was ascribed to the ATP that facilitated the formation and homogenous distribution of small Ag NPs. The resulted sensor achieved 95% of the steady-state current within 2s and had a 2.4 μM detection limit of H(2)O(2).

  20. Molecular simulations of the electric double layer structure, differential capacitance, and charging kinetics for N-methyl-N-propylpyrrolidinium bis(fluorosulfonyl)imide at graphite electrodes.

    PubMed

    Vatamanu, Jenel; Borodin, Oleg; Smith, Grant D

    2011-03-31

    Molecular dynamics simulations were performed on N-methyl-N-propylpyrrolidinium bis(fluorosulfonyl)imide (pyr(13)FSI) room temperature ionic liquid (RTIL) confined between graphite electrodes as a function of applied potential at 393 and 453 K using an accurate force field developed in this work. The electric double layer (EDL) structure and differential capacitance (DC) of pyr(13)FSI was compared with the results of the previous study of a similar RTIL pyr(13)bis(trifluoromethanesulfonyl)imide (pyr(13)TFSI) with a significantly larger anion [ Vatamanu, J.; Borodin, O.; Smith, G. D. J. Am. Chem. Soc. 2010, 132, 14825]. Intriguingly, the smaller size of the FSI anion compared to TFSI did not result in a significant increase of the DC on the positive electrode. Instead, a 30% higher DC was observed on the negative electrode for pyr(13)FSI compared to pyr(13)TFSI. The larger DC observed on the negative electrode for pyr(13)FSI compared to pyr(13)TFSI was associated with two structural features of the EDL: (a) a closer approach of FSI compared to TFSI to the electrode surface and (b) a faster rate (vs potential decrease) of anion desorption from the electrode surface for FSI compared to TFSI. Additionally, the limiting behavior of DC at large applied potentials was investigated. Finally, we show that constant potential simulations indicate time scales of hundreds of picoseconds required for electrode charge/discharge and EDL formation.

  1. Flame structures in the pressurized methane-air combustor

    SciTech Connect

    Yamamoto, Tsuyoshi; Miyazaki, Tomonaga, Furuhata, Tomohiko; Arai, Norio

    1998-07-01

    This study has been carried out in order to investigate the applicability of a pressurized and fuel-rich burner at a first stage combustor for a newly proposed chemical gas turbine system. The flammability limits, exhaust gas composition and the NO{sub x} emission characteristics under the pressurized conditions of 1.1--4.1 MPa have been investigated in a model combustor. This paper focuses on the influence of pressure and F/A equivalence ratio on flame structures of pressurized combustion with methane and air to obtain detailed data for designing of fuel-rich combustor for gas turbine application. The flame under fuel-rich condition and pressure of 1 MPa showed underventilated structure like other atmospheric fuel-rich flames while the flame under pressure over 1.5 MPa had shapes as fuel-lean flame. The flame becomes longer as the pressure was increased under the fuel-lean conditions, which under fuel-rich condition the influence of pressure on flame length was smaller in comparison with the flame under fuel-lean conditions. These results give an opportunity for developing smaller combustor under fuel-rich and pressurized condition compared to fuel-lean one. Numerical simulation has been done for defining the temperature profile in the model combustor using the k-{var{underscore}epsilon} turbulence model and three-step reaction model. The comparison between theoretical results and experimental data showed fair agreements.

  2. In situ synthesis of 3D CoS nanoflake/Ni(OH)₂ nanosheet nanocomposite structure as a candidate supercapacitor electrode.

    PubMed

    Li, Songzhan; Wen, Jian; Chen, Tian; Xiong, Liangbin; Wang, Jianbo; Fang, Guojia

    2016-04-08

    A three-dimensional (3D) CoS/Ni(OH)2 nanocomposite structure based on CoS nanoflakes and two-dimensional (2D) Ni(OH)2 nanosheets were in situ synthesized on Ni foam by a whole hydrothermal reaction and electrodeposition process. The 3D CoS/Ni(OH)2 nanocomposite structures demonstrate the combined advantages of a sustained cycle stability of CoS and high specific capacitance from Ni(OH)2. The obtained CoS/Ni(OH)2 nanocomposite structures on Ni foam can directly serve as a binder-free electrode for a supercapacitor. For the 3D CoS/Ni(OH)2 nanocomposite electrode, the high specific capacitance is 1837 F g(-1) at a scan rate of 1 mV s(-1), which is obviously higher than both the bare CoS electrode and Ni(OH)2 electrode. The galvanostatic charge and discharge measurements illustrate that the 3D CoS/Ni(OH)2 nanocomposite electrode possesses excellent cycle stability, and it keeps a 95.8% retention of the initial capacity after 5000 cycles. Electrochemical impedance spectroscopy measurements also confirm that the 3D CoS/Ni(OH)2 nanocomposite electrode has better electrochemical characteristics. These remarkable performances can be attributed to the unique 3D nanoporous structure of CoS/Ni(OH)2 which leads to a large accessible surface area and a high stability during long-term operation. In addition, 2D Ni(OH)2 nanosheets in 3D nanocomposite structures can afford rapid mass transport and a strong synergistic effect of CoS and Ni(OH)2 as individual compositions contribute to the high performance of the nanocomposite structure electrode. These results may promote the design and implementation of nanocomposite structures in advanced supercapacitors.

  3. Calculation and measurement of a neutral air flow velocity impacting a high voltage capacitor with asymmetrical electrodes

    SciTech Connect

    Malík, M. Primas, J.; Kopecký, V.; Svoboda, M.

    2014-01-15

    This paper deals with the effects surrounding phenomenon of a mechanical force generated on a high voltage asymmetrical capacitor (the so called Biefeld-Brown effect). A method to measure this force is described and a formula to calculate its value is also given. Based on this the authors derive a formula characterising the neutral air flow velocity impacting an asymmetrical capacitor connected to high voltage. This air flow under normal circumstances lessens the generated force. In the following part this velocity is measured using Particle Image Velocimetry measuring technique and the results of the theoretically calculated velocity and the experimentally measured value are compared. The authors found a good agreement between the results of both approaches.

  4. CAD/CAM-designed 3D-printed electroanalytical cell for the evaluation of nanostructured gas-diffusion electrodes.

    PubMed

    Chervin, Christopher N; Parker, Joseph F; Nelson, Eric S; Rolison, Debra R; Long, Jeffrey W

    2016-04-29

    The ability to effectively screen and validate gas-diffusion electrodes is critical to the development of next-generation metal-air batteries and regenerative fuel cells. The limiting electrode in a classic two-terminal device such as a battery or fuel cell is difficult to discern without an internal reference electrode, but the flooded electrolyte characteristic of three-electrode electroanalytical cells negates the prime function of an air electrode-a void volume freely accessible to gases. The nanostructured catalysts that drive the energy-conversion reactions (e.g., oxygen reduction and evolution in the air electrode of metal-air batteries) are best evaluated in the electrode structure as-used in the practical device. We have designed, 3D-printed, and characterized an air-breathing, thermodynamically referenced electroanalytical cell that allows us to mimic the Janus arrangement of the gas-diffusion electrode in a metal-air cell: one face freely exposed to gases, the other wetted by electrolyte.

  5. Influence of cationic structures on oxygen reduction reaction at Pt electrode in fluorohydrogenate ionic liquids

    NASA Astrophysics Data System (ADS)

    Kiatkittikul, Pisit; Yamaguchi, Jumpei; Taniki, Ryosuke; Matsumoto, Kazuhiko; Nohira, Toshiyuki; Hagiwara, Rika

    2014-11-01

    Various parameters related to the oxygen reduction reaction (ORR) on a Pt electrode such as kinetically limited current density (jk), yield of H2O2 (XH2O2), and solubility (C) and diffusion coefficient (D) of oxygen were evaluated at 298 K in fluorohydrogenate ionic liquids (FHILs) using the rotating ring-disk electrode (RRDE) method. The FHILs investigated in this study were 1-ethyl-3-methylimidazolium fluorohydrogenates (EMIm(FH)1.3F and EMIm(FH)2.3F), N-ethyl-N-methyl pyrrolidinium fluorohydrogenates (EMPyr(FH)1.7F and EMPyr(FH)2.3F), trimethylsulfonium fluorohydrogenate (S111(FH)1.9F), triethyl-n-pentylphosphonium fluorohydrogenate (P2225(FH)2.1F), and 5-azoniaspiro[4.4]nonane fluorohydrogenate (AS[4.4](FH)2.0F). Among them, EMPyr(FH)1.7F showed the largest jk value (-1.5 mA cm-2) at 0.7 V vs. RHE. EMPyr(FH)1.7F, EMPyr(FH)2.3F, and P2225(FH)2.1F showed small XH2O2 values around 1.5% at a disk electrode potential of 0.2 V vs. RHE. The C and D values obtained for the FHILs were in the ranges of 0.23-1.3 mmol dm-3 and (1.1-3.2) × 10-5 cm2 s-1, respectively. The crossover currents of oxygen in the FHILs were estimated using the obtained C and D values, which were of the same order of magnitude as that for a 0.5 M H2SO4 aqueous solution.

  6. Laser printing and femtosecond laser structuring of electrode materials for the manufacturing of 3D lithium-ion micro-batteries

    NASA Astrophysics Data System (ADS)

    Smyrek, P.; Kim, H.; Zheng, Y.; Seifert, H. J.; Piqué, A.; Pfleging, W.

    2016-04-01

    Recently, three-dimensional (3D) electrode architectures have attracted great interest for the development of lithium-ion micro-batteries applicable for Micro-Electro-Mechanical Systems (MEMS), sensors, and hearing aids. Since commercial available micro-batteries are mainly limited in overall cell capacity by their electrode footprint, new processing strategies for increasing both capacity and electrochemical performance have to be developed. In case of such standard microbatteries, two-dimensional (2D) electrode arrangements are applied with thicknesses up to 200 μm. These electrode layers are composed of active material, conductive agent, graphite, and polymeric binder. Nevertheless, with respect to the type of active material, the active material to conductive agent ratio, and the film thickness, such thick-films suffer from low ionic and electronic conductivities, poor electrolyte accessibility, and finally, limited electrochemical performance under challenging conditions. In order to overcome these drawbacks, 3D electrode arrangements are under intense investigation since they allow the reduction of lithium-ion diffusion pathways in between inter-digitated electrodes, even for electrodes with enhanced mass loadings. In this paper, we present how to combine laser-printing and femtosecond laser-structuring for the development of advanced 3D electrodes composed of Li(Ni1/3Mn1/3Co1/3)O2 (NMC). In a first step, NMC thick-films were laser-printed and calendered to achieve film thicknesses in the range of 50 μm - 80 μm. In a second step, femtosecond laser-structuring was carried out in order to generate 3D architectures directly into thick-films. Finally, electrochemical cycling of laser-processed films was performed in order to evaluate the most promising 3D electrode designs suitable for application in long life-time 3D micro-batteries.

  7. Fuel cell electrode structures containing sulfonated organosilane-based proton conductors

    NASA Astrophysics Data System (ADS)

    Eastcott, Jennie I.; Yarrow, Kaitlyn M.; Pedersen, Andrew W.; Easton, E. Bradley

    2012-01-01

    Ceramic carbon electrodes (CCE) for PEM fuel cells have been prepared in a one-pot procedure from a mixture of tetra ethyl orthosilicate (TEOS) and 3-trihydroxysilyl-1-propanesulfonic acid (TPS) polymerized in the presence of a platinized carbon with concurrent spray deposition of the partially gelled ink onto a gas diffusion layer. The CCE showed fuel cell performance comparable to commercially available Nafion-based cathodes. This high activity is explained in terms of the high electrochemically active surface area resulting from the enhanced proton conductivity in the CCE.

  8. Development of a Flexible Non-Metal Electrode for Cell Stimulation and Recording

    PubMed Central

    Gong, Cihun-Siyong Alex; Syu, Wun-Jia; Lei, Kin Fong; Hwang, Yih-Shiou

    2016-01-01

    This study presents a method of producing flexible electrodes for potentially simultaneously stimulating and measuring cellular signals in retinal cells. Currently, most multi-electrode applications rely primarily on etching, but the metals involved have a certain degree of brittleness, leaving them prone to cracking under prolonged pressure. This study proposes using silver chloride ink as a conductive metal, and polydimethysiloxane (PDMS) as the substrate to provide electrodes with an increased degree of flexibility to allow them to bend. This structure is divided into the electrode layer made of PDMS and silver chloride ink, and a PDMS film coating layer. PDMS can be mixed in different proportions to modify the degree of rigidity. The proposed method involved three steps. The first segment entailed the manufacturing of the electrode, using silver chloride ink as the conductive material, and using computer software to define the electrode size and micro-engraving mechanisms to produce the electrode pattern. The resulting uniform PDMS pattern was then baked onto the model, and the flow channel was filled with the conductive material before air drying to produce the required electrode. In the second stage, we tested the electrode, using an impedance analyzer to measure electrode cyclic voltammetry and impedance. In the third phase, mechanical and biocompatibility tests were conducted to determine electrode properties. This study aims to produce a flexible, non-metallic sensing electrode which fits snugly for use in a range of measurement applications. PMID:27690049

  9. Method of bonding an interconnection layer on an electrode of an electrochemical cell

    DOEpatents

    Pal, Uday B.; Isenberg, Arnold O.; Folser, George R.

    1992-01-01

    An electrochemical cell containing an air electrode (16), contacting electrolyte and electronically conductive interconnection layer (26), and a fuel electrode, has the interconnection layer (26) attached by: (A) applying a thin, closely packed, discrete layer of LaCrO.sub.3 particles (30), doped with an element selected from the group consisting of Ca, Sr, Co, Ba, Mg and their mixtures on a portion of the air electrode, and then (B) electrochemical vapor depositing a dense skeletal structure (32) between and around the doped LaCrO.sub.3 particles (30).

  10. Method of bonding an interconnection layer on an electrode of an electrochemical cell

    DOEpatents

    Pal, U.B.; Isenberg, A.O.; Folser, G.R.

    1992-01-14

    An electrochemical cell containing an air electrode, contacting electrolyte and electronically conductive interconnection layer, and a fuel electrode, has the interconnection layer attached by: (A) applying a thin, closely packed, discrete layer of LaCrO[sub 3] particles, doped with an element selected from the group consisting of Ca, Sr, Co, Ba, Mg and their mixtures on a portion of the air electrode, and then (B) electrochemical vapor depositing a dense skeletal structure between and around the doped LaCrO[sub 3] particles. 2 figs.

  11. Radio frequency breakdown between structured parallel plate electrodes with a millimetric gap in low pressure gases

    SciTech Connect

    Legradic, B.; Howling, A. A.; Hollenstein, C.

    2010-10-15

    This paper presents an investigation into radio frequency (rf) breakdown for electrodes with holes or protrusions, approximating the situation in real reactors and providing a benchmark for fluid simulations. rf breakdown curves (voltage versus pressure) generally show a steep left-hand branch at low pressures and a flatter right-hand branch at higher pressures. Introducing protrusions or holes in parallel plate electrodes will lower the breakdown voltage in certain conditions. Yet experiments show that the breakdown curves are not perceptibly influenced by the increased electric field at sharp edges or ridges. Instead, both experiments and simulation show that breakdown at high pressure will occur at the protrusion providing the smallest gap, while breakdown at low pressure will occur in the aperture providing the largest gap. This holds true as long as the feature in question is wide enough. Features that are too narrow will lose too many electrons due to diffusion, either to the walls of the apertures or to the surroundings of the protrusion, which negates the effect on the breakdown voltage. The simulation developed presents a tool to aid the design of complex rf parts for dark-space shielding.

  12. Anode potential influences the structure and function of anodic electrode and electrolyte-associated microbiomes

    NASA Astrophysics Data System (ADS)

    Dennis, Paul G.; Virdis, Bernardino; Vanwonterghem, Inka; Hassan, Alif; Hugenholtz, Phil; Tyson, Gene W.; Rabaey, Korneel

    2016-12-01

    Three bioelectrochemical systems were operated with set anode potentials of +300 mV, +550 mV and +800 mV vs. Standard Hydrogen Electrode (SHE) to test the hypothesis that anode potential influences microbial diversity and is positively associated with microbial biomass and activity. Bacterial and archaeal diversity was characterized using 16 S rRNA gene amplicon sequencing, and biofilm thickness was measured as a proxy for biomass. Current production and substrate utilization patterns were used as measures of microbial activity and the mid-point potentials of putative terminal oxidases were assessed using cyclic voltammetry. All measurements were performed after 4, 16, 23, 30 and 38 days. Microbial biomass and activity differed significantly between anode potentials and were lower at the highest potential. Anodic electrode and electrolyte associated community composition was also significantly influenced by anode potential. While biofilms at +800 mV were thinner, transferred less charge and oxidized less substrate than those at lower potentials, they were also associated with putative terminal oxidases with higher mid-point potentials and generated more biomass per unit charge. This indicates that microbes at +800 mV were unable to capitalize on the potential for additional energy gain due to a lack of adaptive traits to high potential solid electron acceptors and/or sensitivity to oxidative stress.

  13. Anode potential influences the structure and function of anodic electrode and electrolyte-associated microbiomes

    PubMed Central

    Dennis, Paul G.; Virdis, Bernardino; Vanwonterghem, Inka; Hassan, Alif; Hugenholtz, Phil; Tyson, Gene W.; Rabaey, Korneel

    2016-01-01

    Three bioelectrochemical systems were operated with set anode potentials of +300 mV, +550 mV and +800 mV vs. Standard Hydrogen Electrode (SHE) to test the hypothesis that anode potential influences microbial diversity and is positively associated with microbial biomass and activity. Bacterial and archaeal diversity was characterized using 16 S rRNA gene amplicon sequencing, and biofilm thickness was measured as a proxy for biomass. Current production and substrate utilization patterns were used as measures of microbial activity and the mid-point potentials of putative terminal oxidases were assessed using cyclic voltammetry. All measurements were performed after 4, 16, 23, 30 and 38 days. Microbial biomass and activity differed significantly between anode potentials and were lower at the highest potential. Anodic electrode and electrolyte associated community composition was also significantly influenced by anode potential. While biofilms at +800 mV were thinner, transferred less charge and oxidized less substrate than those at lower potentials, they were also associated with putative terminal oxidases with higher mid-point potentials and generated more biomass per unit charge. This indicates that microbes at +800 mV were unable to capitalize on the potential for additional energy gain due to a lack of adaptive traits to high potential solid electron acceptors and/or sensitivity to oxidative stress. PMID:27991591

  14. Steady-state characteristics and transient response of MgZnO-based metal-semiconductor-metal solar-blind ultraviolet photodetector with three types of electrode structures.

    PubMed

    Wang, Ping; Zhen, Qinghong; Tang, Qing; Yang, Yintang; Guo, Lixin; Ding, Kai; Huang, Feng

    2013-07-29

    Detailed studies of MgZnO-based metal-semiconductor-metal (MSM) solar-blind ultraviolet photodetector with different electrode structures are performed. A two-dimensional physical model is established based on the Poisson's equation and time-dependent continuity equations, which is verified by our experimental data of conventional electrode MSM detector. The steady-state characteristics and transient response of semicircular and triangular electrode MSM detectors are also investigated by this model. Compared with the conventional electrode, semicircular and triangular electrode devices exhibit a substantial improvement on the photocurrent. At a bias of 10 V, the steady-state saturated photocurrents for semicircular and triangular electrode devices are 14.69 nA and 24.37 nA respectively, corresponding to a 20.5% and 100% increase over the conventional electrode detector. Meanwhile, the transient peak photocurrents reach 31.38 nA and 52.09 nA respectively, both of which are notably larger than that of conventional device.

  15. Comparison of electrode structures and photovoltaic properties of porphyrin-sensitized solar cells with TiO2 and Nb, Ge, Zr-added TiO2 composite electrodes.

    PubMed

    Imahori, Hiroshi; Hayashi, Shinya; Umeyama, Tomokazu; Eu, Seunghun; Oguro, Akane; Kang, Soonchul; Matano, Yoshihiro; Shishido, Tetsuya; Ngamsinlapasathian, Supachai; Yoshikawa, Susumu

    2006-12-19

    Electrode structures and photovoltaic properties of porphyrin-sensitized solar cells with TiO2 and Nb-, Ge-, and Zr-added TiO2 composite electrodes were examined to disclose the effects of partial substitution of Ti atom by the other metals in the composite electrodes. The TiO2 and Nb-, Ge-, and Zr-added TiO2 composite electrodes were prepared by sol-gel process using laurylamine hydrochloride as a template for the formation of micellar precursors yielding well-defined mesoporous nanocrystalline structures, as in the cases of the formation of silica and titania tubules and nanoparticles by the templating mechanism. The TiO2 and Nb-, Ge-, and Zr-added TiO2 composite electrodes were characterized by transmission electron microscopy, BET surface area analysis, X-ray diffraction analysis, Raman spectroscopy, and impedance measurements. The TiO2 anatase nanocrystalline structure is retained after doping a small amount (5 mol %) of Nb, Ge, or Zr into the TiO2 structure, suggesting the homogeneous distribution of the doped metals with replacing Ti atom by the doped metal. The power conversion efficiency of the porphyrin-sensitized solar cells increases in the order Zr-added TiO2 (0.8%) < Nb-added TiO2 (1.2%) < TiO2 (2.0%) < Ge-added TiO2 cells (2.4%) under the same conditions. The improvement of cell performance of the Ge-added TiO2 cell results from the negative shift of the conduction band of the Ge-added TiO2 electrode. The Ge-added TiO2 cell exhibited a maximum power conversion efficiency of 3.5% when the porphyrin was adsorbed onto the surface of the Ge-added TiO2 electrode with a thickness of 4 microm in MeOH for 1 h.

  16. Monodisperse CoFe2O4 nanoparticles supported on Vulcan XC-72: High performance electrode materials for lithium-air and lithium-ion batteries

    NASA Astrophysics Data System (ADS)

    Şener, Tansel; Kayhan, Emine; Sevim, Melike; Metin, Önder

    2015-08-01

    Addressed herein is the preparation and the electrode performance of monodisperse CoFe2O4 nanoparticles (NPs) supported on Vulcan XC-72 for the Lithium-air battery (LAB) and Lithium-ion battery (LIB). Monodisperse CoFe2O4 NPs were synthesized by the thermal decomposition of cobalt(II) acetylacetonate and iron(III) acetylacetonate in oleylamine and oleic acid in the presence of 1,2-tetradecanediol and benzyl ether. As-prepared CoFe2O4 NPs with a particle size of 11 nm were then supported on Vulcan XC-72 (Vulcan-CoFe2O4) at different theoretical loadings (20, 40 and 60 wt % CoFe2O4 NPs) by using the simple liquid phase self assembly method. CoFe2O4 NPs dispersed on Vulcan-CoFe2O4 composites were characterized by transmission electron microscopy (TEM), powder X-ray diffraction (PXRD) and atomic absorption spectroscopy (AAS). The AAS analyses indicated that the Vulcan-CoFe2O4 composites with different loadings were included 3.7, 8.1 and 16.4 wt % CoFe2O4 on the metal basis. The electrode performance of Vulcan-CoFe2O4 composites were evaluated as the anode active material for LIB and cathode active material for LABs by performing the galvanostatic charge-discharge tests. The highest discharge capacity for both LAB (7510 mAh g(Vulcan+CoFe2O4)-1; 13380 mAh gCoFe2O4-1 @ 0.1C) and LIB (863 mAh g(Vulcan+CoFe2O4)-1; 9330 mAh gCoFe2O4-1@ 0.1C) was investigated with 16.4 wt % CoFe2O4.

  17. Evaluation of Air Coupled Ultrasound for Composite Aerospace Structure

    NASA Astrophysics Data System (ADS)

    Tat, H.; Georgeson, G.; Bossi, R.

    2009-03-01

    Non-contact air coupled ultrasound suffers from the high acoustic impedance mismatch characteristics of air to solid interfaces. Advances in transducer technology, particularly MEMS, have improved the acoustic impedance match at the transmission stage and the signal to noise at the reception stage. Comparisons of through transmission (TTU) scanning of laminate and honeycomb test samples using conventional piezoelectric air coupled transducers, new MEMS air coupled transducers, and standard water coupled inspections have been performed to assess the capability. An additional issue for air coupled UT inspection is the need for a lean implementation for both manufacturing and in-service operations. Concepts and applications utilizing magnetic coupling of transducers have been developed that allows air coupled inspection operations in compact low cost configurations.

  18. A Novel Gate Electrode Structure for Reduction of Gate Resistance of Sub-0.1 µm RF/Mixed-Signal Metal Oxide Semiconductor Field-Effect Transistors

    NASA Astrophysics Data System (ADS)

    Nagase, Hirokazu; Tanabe, Akira; Umeda, Kyoko; Watanabe, Takashi; Hayashi, Yoshihiro

    2009-04-01

    To reduce noise and enhance gain for scaled-down metal oxide semiconductor field-effect transistors (MOSFETs), a novel gate electrode structure “direct finger contact (DFC)” is proposed. The DFC structure reduces the gate electrode resistance by 40%. NF50 (noise figure when the input impedance is 50 Ω) is reduced by 4% with the gate length L = 48 nm, the gate width Wfinger =1 µm, and the number of finger N =20. This structure is suitable for low-noise sub-0.1 µm RF/mixed-signal system on chips (SoCs).

  19. Silver decorated LaMnO3 nanorod/graphene composite electrocatalysts as reversible metal-air battery electrodes

    NASA Astrophysics Data System (ADS)

    Hu, Jie; Liu, Qiunan; Shi, Lina; Shi, Ziwei; Huang, Hao

    2017-04-01

    Perovskite LaMnO3 nanorod/reduced graphene oxides (LMO-NR/RGO) decorated with Ag nanoparticles are studied as a bifunctional catalyst for oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) in alkaline electrolyte. LMO-NR/RGO composites are synthesized by using cetyltrimethyl ammonium bromide (CTAB) as template via a simple hydrothermal reaction followed by heat treatment; overlaying of Ag nanoparticles is obtained through a traditional silver mirror reaction. Electron microscopy reveals that LMO-NR is embedded between the sheets of RGO, and the material is homogeneously overlaid with Ag nanoparticles. The unique composite morphology of Ag/LMO-NR/RGO not only enhances the electron transport property by increasing conductivity but also facilitates the diffusion of electrolytes and oxygen. As confirmed by electrochemical testing, Ag/LMO-NR/RGO exhibits very strong synergy with Ag nanoparticles, LMO-NR, and RGO, and the catalytic activities of Ag/LMO-NR/RGO during ORR and OER are significantly improved. With the novel catalyst, the homemade zinc-air battery can be reversibly charged and discharged and display a stable cycle performance, indicating the great potential of this composite as an efficient bifunctional electrocatalyst for metal-air batteries.

  20. Reflection spectra of distorted cholesteric liquid crystal structures in cells with interdigitated electrodes.

    PubMed

    Rumi, Mariacristina; White, Timothy J; Bunning, Timothy J

    2014-06-30

    We studied the appearance of second- and third-order Bragg reflections in cholesteric liquid crystals (CLCs) in cells where the electric field was perpendicular to the helical axis. Second-order reflections with reflectance values as large as 80% of the first-order one were observed in the gap regions of alignment cells with interdigitated electrodes for CLC mixtures with pitches in the range 0.5-1.0 μm upon application of a field. The characterization was enabled by local probing of the CLC using a microspectrophotometer. LC cells that are transparent in the visible spectrum in the off-state and become colored upon application of a field due the second- or third-order reflection band appearance were demonstrated. The spectral position of the higher-order Bragg reflections can also be tuned by adjusting the magnitude of the electric field.

  1. Bifunctional catalytic electrode

    NASA Technical Reports Server (NTRS)

    Cisar, Alan (Inventor); Murphy, Oliver J. (Inventor); Clarke, Eric (Inventor)

    2005-01-01

    The present invention relates to an oxygen electrode for a unitized regenerative hydrogen-oxygen fuel cell and the unitized regenerative fuel cell having the oxygen electrode. The oxygen electrode contains components electrocatalytically active for the evolution of oxygen from water and the reduction of oxygen to water, and has a structure that supports the flow of both water and gases between the catalytically active surface and a flow field or electrode chamber for bulk flow of the fluids. The electrode has an electrocatalyst layer and a diffusion backing layer interspersed with hydrophilic and hydrophobic regions. The diffusion backing layer consists of a metal core having gas diffusion structures bonded to the metal core.

  2. Dependence of image flickering of negative dielectric anisotropy liquid crystal on the flexoelectric coefficient ratio and the interdigitated electrode structure

    NASA Astrophysics Data System (ADS)

    Lee, Hyojin; Kim, Hyungmin; Kim, Jongyoon; Lee, Ji-Hoon

    2016-02-01

    We experimentally measured the splay (e s) and the bend flexoelectric coefficients (e b) of liquid crystal (LC) mixtures with negative dielectric anisotropy and investigated their effect on the image flicker of the LC mixtures driven with a low frequency electric field. Using the experimentally measured e s and e b, we simulated the transmittance (TR) response with the continuum model. First, we confirmed that the TR simulation results were approximated to the experimental data with only small variation. Second, we varied the simulation parameters of e s , e b, the separation (S), and the width (W) of the interdigitated electrodes and tried to find the optimum condition showing the least image flicker. Given W  =  3.0 μm and e b  =  5.7 pC m-1, it was found that the image flicker could be minimized when the e s /e b value was about 2.4 and the S/W ratio was about 1.5. Because the e s /e b value of the rod-like LC material is generally less than 1, it is desirable to design an interdigitated electrode structure to minimize the image flicker effect.

  3. Effect of multilayer structure on cyclic performance of Si/Fe anode electrode in lithium-ion secondary batteries.

    PubMed

    Kang, Hee-Kook; Lee, Seong-Rae; Cho, Won Il; Won Cho, Byung

    2013-02-07

    A buffer-strengthened Si/Fe multilayer film, consisting of amorphous silicon layers and polycrystalline Fe layers, is investigated as the anode for Li-ion batteries. This film can achieve a stable cycle-life performance with a high capacity. Decreasing the thickness of the Fe layer can lead to a higher capacity, which is related to the fast transport of the Li ion, but the cyclic performance deteriorates with repeated cycling. In contrast, increasing the thickness of the Fe buffer layers and the number of deposit stacks improves the cycle life with high reversibility. Because of the strain in the Si layers suppressed by the primary multilayer structure, the long-term strength is preserved and the substantial fracture toughness is enhanced by the increasing numbers of effective grain boundaries and interfacial layers. In addition, we demonstrate that the Ti underlayer promotes the electrochemical properties in the Si/Fe multilayer for various Fe layer thicknesses because of the enhanced adhesion of the interfacial electrode and current collector. The mechanically optimized Si/Fe multilayer films can have superior cycle-life performances and higher capacities. Notably, the 16-bilayer deposited electrode exhibits an excellent capacity retention of ~95% with ~204 mAh g(-1) over 300 cycles at a 1 C rate.

  4. Electrode compositions

    DOEpatents

    Block, J.; Fan, X.

    1998-10-27

    An electrode composition is described for use as an electrode in a non-aqueous battery system. The electrode composition contains an electrically active powder in a solid polymer and, as a dispersant, a C{sub 8}-C{sub 15} alkyl capped oligomer of a hexanoic acid that is electrochemically inert at 2.5--4.5 volts.

  5. Electrode compositions

    DOEpatents

    Block, Jacob; Fan, Xiyun

    1998-01-01

    An electrode composition for use as an electrode in a non-aqueous battery system. The electrode composition contains an electrically active powder in a solid polymer and, as a dispersant, a C.sub.8 -C.sub.15 alkyl capped oligomer of a hexanoic acid that is electrochemically inert at 2.5-4.5 volts.

  6. A perovskite oxide with high conductivities in both air and reducing atmosphere for use as electrode for solid oxide fuel cells

    NASA Astrophysics Data System (ADS)

    Lan, Rong; Cowin, Peter I.; Sengodan, Sivaprakash; Tao, Shanwen

    2016-08-01

    Electrode materials which exhibit high conductivities in both oxidising and reducing atmospheres are in high demand for solid oxide fuel cells (SOFCs) and solid oxide electrolytic cells (SOECs). In this paper, we investigated Cu-doped SrFe0.9Nb0.1O3‑δ finding that the primitive perovskite oxide SrFe0.8Cu0.1Nb0.1O3‑δ (SFCN) exhibits a conductivity of 63 Scm‑1and 60 Scm‑1 at 415 °C in air and 5%H2/Ar respectively. It is believed that the high conductivity in 5%H2/Ar is related to the exsolved Fe (or FeCu alloy) on exposure to a reducing atmosphere. To the best of our knowledge, the conductivity of SrFe0.8Cu0.1Nb0.1O3‑δ in a reducing atmosphere is the highest of all reported oxides which also exhibit a high conductivity in air. Fuel cell performance using SrFe0.8Cu0.1Nb0.1O3‑δ as the anode, (Y2O3)0.08(ZrO2)0.92 as the electrolyte and La0.8Sr0.2FeO3‑δ as the cathode achieved a power density of 423 mWcm‑2 at 700 °C indicating that SFCN is a promising anode for SOFCs.

  7. A perovskite oxide with high conductivities in both air and reducing atmosphere for use as electrode for solid oxide fuel cells

    PubMed Central

    Lan, Rong; Cowin, Peter I.; Sengodan, Sivaprakash; Tao, Shanwen

    2016-01-01

    Electrode materials which exhibit high conductivities in both oxidising and reducing atmospheres are in high demand for solid oxide fuel cells (SOFCs) and solid oxide electrolytic cells (SOECs). In this paper, we investigated Cu-doped SrFe0.9Nb0.1O3−δ finding that the primitive perovskite oxide SrFe0.8Cu0.1Nb0.1O3−δ (SFCN) exhibits a conductivity of 63 Scm−1and 60 Scm−1 at 415 °C in air and 5%H2/Ar respectively. It is believed that the high conductivity in 5%H2/Ar is related to the exsolved Fe (or FeCu alloy) on exposure to a reducing atmosphere. To the best of our knowledge, the conductivity of SrFe0.8Cu0.1Nb0.1O3−δ in a reducing atmosphere is the highest of all reported oxides which also exhibit a high conductivity in air. Fuel cell performance using SrFe0.8Cu0.1Nb0.1O3−δ as the anode, (Y2O3)0.08(ZrO2)0.92 as the electrolyte and La0.8Sr0.2FeO3−δ as the cathode achieved a power density of 423 mWcm−2 at 700 °C indicating that SFCN is a promising anode for SOFCs. PMID:27545200

  8. Magnetohydrodynamic electrode

    DOEpatents

    Boquist, Carl W.; Marchant, David D.

    1978-01-01

    A ceramic-metal composite suitable for use in a high-temperature environment consists of a refractory ceramic matrix containing 10 to 50 volume percent of a continuous high-temperature metal reinforcement. In a specific application of the composite, as an electrode in a magnetohydrodynamic generator, the one surface of the electrode which contacts the MHD fluid may have a layer of varying thickness of nonreinforced refractory ceramic for electrode temperature control. The side walls of the electrode may be coated with a refractory ceramic insulator. Also described is an electrode-insulator system for a MHD channel.

  9. Fine structure of modal focusing effect in a three dimensional plasma-sheath-lens formed by disk electrodes

    SciTech Connect

    Stamate, Eugen; Yamaguchi, Masahito

    2015-08-31

    Modal and discrete focusing effects associated with three-dimensional plasma-sheath-lenses show promising potential for applications in ion beam extraction, mass spectrometry, plasma diagnostics and for basic studies of plasma sheath. The ion focusing properties can be adjusted by controlling the geometrical structure of the plasma-sheath-lens and plasma parameters. The positive and negative ion kinetics within the plasma-sheath-lens are investigated both experimentally and theoretically and a modal focusing ring is identified on the surface of disk electrodes. The focusing ring is very sensitive to the sheath thickness and can be used to monitor very small changes in plasma parameters. Three dimensional simulations are found to be in very good agreement with experiments.

  10. Evaluation of electromechanical coupling parameters of piezoelectric materials by using piezoelectric cantilever with coplanar electrode structure in quasi-stasis.

    PubMed

    Zheng, Xuejun; Zhu, Yuankun; Liu, Xun; Liu, Jing; Zhang, Yong; Chen, Jianguo

    2014-02-01

    Based on Timoshenko beam theory, a principle model is proposed to establish the relationship between electric charge and excitation acceleration, and in quasi-stasis we apply the direct piezoelectric effect of multilayer cantilever with coplanar electrode structure to evaluate the piezoelectric strain coefficient d15 and electromechanical coupling coefficient k15. They are measured as 678 pC/N and 0.74 for the commercial piezoelectric ceramic lead zirconate titanate (PZT-51) bulk specimen and 656 pC/N and 0.63 for the lead magnesium niobate (PMN) bulk specimen, and they are in agreement with the calibration and simulation values. The maximum of relative errors is less than 4.2%, so the proposed method is reliable and convenient.

  11. Study of structure and properties of oxide electrode materials (Fe3O4, AZO, SRO) and their device applications

    NASA Astrophysics Data System (ADS)

    Olga, Chichvarina

    Ferroelectric thin film capacitor heterostructures have attracted considerable attention in the last decade because of their potential applications in piezoelectric sensors, actuators, power generators and non-volatile memory devices. Strongly correlated all-perovskite oxide heterojunctions are of a particular interest, as their material properties (electronic, structural, magnetic and optical, etc.) can be tuned via doping, interface effect, applied electrical field, and formation of two-dimensional electron gas (2DEG), etc. The right selection of electrode material for this type of capacitor-like structures may modify and enhance the performance of a device, as the electrode/barrier layer interfaces can significantly influence its macroscopic properties. Although there is a number of reports on the effect of electrode interfaces on the properties of PZT capacitors deposited on SRO buffered STO substrate, very little is known about Fe3O4/PZT and AZO/PZT electrode interfaces. This thesis comprises two parts. In the first part we present a systematic study of the structural, transport, magnetic and optical properties of oxide thin films: AZO, Fe3O4 and SRO. These monolayers were fabricated via pulsed laser deposition technique on quartz, MgO and STO substrates respectively. The second part of this thesis elucidates the behaviour of these three oxides as electrode components in PZT/SRO/STO heteroepitaxial structures. The highlights of the work are summarized below: 1) Zinc-blende (ZB) phase of ZnO was predicted to possess higher values of conductivity and higher doping efficiency compared to its wurzite counterpart and thus has greater chances of facilitating the fabrication of ZnO-electrode-based devices. However, zinc-blende is a metastable phase, and it is challenging to obtain single-phase ZB. To tackle this challenge we tuned parameters such-as film thickness, substrate and annealing effect, and achieved a ZB phase of Ti-doped ZnO, ZB-(Zn1-xTix)O thin film. An

  12. No Longer the Outlier: Updating the Air Component Structure

    DTIC Science & Technology

    2016-06-23

    updates and make adjustments to the air component organizational construct. Spring 2016 | 5 Senior Leader Perspective —Lt Gen CQ Brown Jr. Commander, US...guidance and past doctrinal mind- sets that shaped the air component organizational construct, COCOMs, joint, and coalition partners do not clearly...desired habitual relationship, why not align the A3 and AOC into a more synergistic organizational construct similar to joint doctrine and aligned with

  13. Force Structure: Preliminary Observations on Air Force A-10 Divestment

    DTIC Science & Technology

    2015-06-25

    disclosure . Therefore, this report omits certain information about military plans or operations, vulnerabilities or capabilities of systems or...Special Operations Command; Headquarters Air Force (A3, A5, A8, A9, and Financial Management); Air Combat Command (A3, A4, A5, and A8); Army (G-3/5/7 and...copyrighted images or other material , permission from the copyright holder may be necessary if you wish to reproduce this material separately. Page 9

  14. Novel electrode structures for large scale dielectrophoretic separations based on textile technology.

    PubMed

    Abidin, Zurina Z; Downes, Les; Markx, Gerard H

    2007-06-15

    The use of dielectrophoresis (DEP) to date has mainly been limited to processing small volumes due to difficulties in the fabrication of microelectrodes over large surface areas. To overcome this problem a novel approach to the construction of micro-electrode arrays has been developed based on weaving. A plain weave cloth was made from 100 microm diameter stainless steel wires and 75 decitex polyester yarns. The stainless steel wires formed the weft, and were kept parallel and apart by a warp of flexible polyester yarns, with a gap of around 150 microm between the metal wires. The metal wires were alternately connected to earth and signal of an AC power source, and it was shown that it was possible to collect yeast cells suspended in deionised water at the metal wire surfaces by dielectrophoresis. The polyester yarn was also found to distort the electric field, creating further areas of electric field non-uniformity around the polyester yarns, further enhancing the capability of the system to attract cells. A 14 ml separation chamber was built from the cloth by alternately sandwiching perspex slabs and cloth together. The DEP chamber was able to effectively collect life yeast from a flow of suspended cells through the cloth using an applied field of 1 MHz at flow rates up to 5 ml min-1. However, some loss occurred due to sedimentation. Also, the chamber was able to separate dead and live yeast cells at 30 Vpk-pk, 2 MHz, with some cell loss due to sedimentation.

  15. Characterization of Piezoresistive PEDOT:PSS Pressure Sensors with Inter-Digitated and Cross-Point Electrode Structures

    PubMed Central

    Wang, Jer-Chyi; Karmakar, Rajat Subhra; Lu, Yu-Jen; Huang, Chiung-Yin; Wei, Kuo-Chen

    2015-01-01

    The piezoresistive characteristics of poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) pressure sensors with inter-digitated (IDE) and cross-point electrode (CPE) structures have been investigated. A small variation of the resistance of the pressure sensors with IDE without bottom indium-tin-oxide (b-ITO) film and with CPE structures was observed owing to the single carrier-conducting pathway. For the IDE pressure sensors with b-ITO, the piezoresistive characteristics at low and high pressure were similar to those of the pressure sensors with IDE without b-ITO and with CPE structures, respectively, leading to increased piezoresistive pressure sensitivity as the PEDOT:PSS film thickness decreased. A maximum sensitivity of more than 42 kΩ/Pa was achieved. When the normal pressure was applied, the increased number of conducting points or the reduced distance between the PEDOT oligomers within the PEDOT:PSS film resulted in a decrease of the resistance. The piezoresistive pressure sensors with a single carrier-conducting pathway, i.e., IDE without b-ITO and CPE structures, exhibited a small relaxation time and a superior reversible operation, which can be advantageous for fast piezoresistive response applications. PMID:25569756

  16. CAD/CAM-designed 3D-printed electroanalytical cell for the evaluation of nanostructured gas-diffusion electrodes

    NASA Astrophysics Data System (ADS)

    Chervin, Christopher N.; Parker, Joseph F.; Nelson, Eric S.; Rolison, Debra R.; Long, Jeffrey W.

    2016-04-01

    The ability to effectively screen and validate gas-diffusion electrodes is critical to the development of next-generation metal-air batteries and regenerative fuel cells. The limiting electrode in a classic two-terminal device such as a battery or fuel cell is difficult to discern without an internal reference electrode, but the flooded electrolyte characteristic of three-electrode electroanalytical cells negates the prime function of an air electrode—a void volume freely accessible to gases. The nanostructured catalysts that drive the energy-conversion reactions (e.g., oxygen reduction and evolution in the air electrode of metal-air batteries) are best evaluated in the electrode structure as-used in the practical device. We have designed, 3D-printed, and characterized an air-breathing, thermodynamically referenced electroanalytical cell that allows us to mimic the Janus arrangement of the gas-diffusion electrode in a metal-air cell: one face freely exposed to gases, the other wetted by electrolyte.

  17. HIGH VOLTAGE ELECTRODES

    DOEpatents

    Murray, J.J.

    1963-04-23

    S>This patent relates to electrode structure for creating an intense direct current electric field which may have a field strength of the order of two to three times that heretofore obtained, with automatic suppression of arcing. The positive electrode is a conventional conductive material such as copper while the negative electrode is made from a special material having a resistivity greater than that of good conductors and less than that of good insulators. When an incipient arc occurs, the moderate resistivity of the negative electrode causes a momentary, localized decrease in the electric field intensity, thus suppressing the flow of electrons and avoiding arcing. Heated glass may be utilized for the negative electrode, since it provides the desired combination of resistivity, capacity, dielectric strength, mechani-cal strength, and thermal stability. (AEC)

  18. Volume-surface barrier discharge in dried air in three-electrode system fed by impulse high voltage with nanosecond rise time

    NASA Astrophysics Data System (ADS)

    Malashin, Maxim; Rebrov, Igor; Nebogatkin, Sergey; Sokolova, Marina; Nikitin, Alexey; Voevodin, Vadim; Krivov, Sergey

    2016-08-01

    Results of experimental investigation of a volume-surface barrier discharge in a three-electrode system under periodic impulse voltage applied to the surface discharge (SD) electrodes and a d.c. potential applied to an additional third electrode are presented. It is shown that there is a strong influence of polarity and amplitude of the d.c. potential on the direct current "extracted" out of the surface discharge plasma layer by electric field of the third electrode. The amount of charged positive species that constitute the "extracted" current prevails under positive impulse voltage for low values of the negative d.c. potential of the third electrode. The amount of negative species prevails with higher values of the positive d.c. positive of the third electrode. Contribution to the topical issue "6th Central European Symposium on Plasma Chemistry (CESPC-6)", edited by Nicolas Gherardi, Ester Marotta and Cristina Paradisi

  19. Structure of porous electrodes in polymer electrolyte membrane fuel cells: An optical reconstruction technique

    NASA Astrophysics Data System (ADS)

    Berejnov, Viatcheslav; Sinton, David; Djilali, Ned

    Computing flows and phase transport in porous media requires a physically representative geometric model. We present a simple method of digitizing the structure of fibrous porous media commonly used in polymer electrolyte membrane (PEM) fuel cells, the so-called gas diffusion layer (GDL). Employing an inverted microscope and image recognition software we process images of the GDL surface collected manually at different focal lengths with micrometer accuracy. Processing the series of images allows retrieval of local depths of the salient in-focus structural elements in each of the different images. These elements are then recombined into a depth-map representing the three-dimensional structure of the GDL surface. Superimposition of the in-focus portions of the structural elements distributed throughout the stack of images yields digitized data describing the geometry and structural attributes of the 3D surface of the GDL fibrous material.

  20. Structure and surface chemistry of Al2O3 coated LiMn2O4 nanostructured electrodes with improved lifetime

    NASA Astrophysics Data System (ADS)

    Waller, G. H.; Brooke, P. D.; Rainwater, B. H.; Lai, S. Y.; Hu, R.; Ding, Y.; Alamgir, F. M.; Sandhage, K. H.; Liu, M. L.

    2016-02-01

    Aluminum oxide coatings deposited on LiMn2O4/carbon fiber electrodes by atomic layer deposition (ALD) are shown to enhance cathode performance in lithium-ion batteries. With a thin Al2O3 coating derived from 10 ALD cycles, the electrodes exhibit 2.5 times greater capacity retention over 500 cycles at a rate of 1C as well as enhanced rate capability and decreased polarization resistance. Structural and surface studies of the electrodes before and after cycling reveal that a near-surface phenomenon is responsible for the improved electrochemical performance. The crystal structure and overall morphology of the LiMn2O4 electrode are found to be unaffected by electrochemical cycling, both for coated and uncoated samples. However, evidence of Mn diffusion into the ALD coatings is observed from both transmission electron microscopy/energy-dispersive X-ray spectroscopy (TEM-EDS) and X-ray Photoelectron Spectroscopy (XPS) after electrochemical cycling. Furthermore, XPS analysis of the Al 2p photoemission peak for the ALD coated electrodes reveal a significant shift in binding energy and peak shape, suggesting the presence of an Al-O-F compound formed by sequestering HF in the electrolyte. These observations provide new insight toward understanding the mechanism in which ultrathin coatings of amphoteric oxides can inhibit capacity loss for LiMn2O4 cathodes in lithium-ion batteries.

  1. Structural phase transition and electrode characteristics of LiMn{sub 2{minus}x}Mg{sub x}O{sub 4} positive electrode material for the lithium secondary battery

    SciTech Connect

    Idemoto, Y.; Udagawa, K.; Koura, N.; Richardson, J. W., Jr.; Takeuchi, K.; Loong, C.-K.

    1999-12-10

    With in mind improving the cycle performance of 4V class lithium manganese oxide positive electrode material for the lithium secondary battery, the authors have been investigating the effects of partial substitution of Mn by another metal. The crystal phase transition in the quaternary spinel LiMn{sub 2{minus}x}Mg{sub x}O{sub 4} was studied by neutron powder diffraction at 200K and DSC measurements at low temperatures. They find that substituting Mn by Mg resulted in a more stable crystal structure with the Jahn-Teller transition suppressed down to low temperature. The charge-discharge characteristics of these positive electrode active materials were investigated at 4V range. Although the discharge capacity decreased with increasing Mg content, the cycle performance was improved with increasing Mg content.

  2. Numerical and experimental evaluation of the relationship between porous electrode structure and effective conductivity of ions and electrons in lithium-ion batteries

    NASA Astrophysics Data System (ADS)

    Inoue, Gen; Kawase, Motoaki

    2017-02-01

    This study aims to develop a correlation equation between a porous electrode structure and the effective conductivity so as to design an optimal structure for a thick electrode layer of a high-capacity battery. We carried out a three-dimensional reconstruction of a lithium cobalt oxide and graphite electrode based on the cross-sectional images obtained via focused ion beam-scanning electron microscopy (FIB-SEM). The Li ion and electron conductivities are evaluated based on the effective conductive path determined from simulation and these values are compared with the experimental results obtained by electrochemical impedance spectroscopy carries out with a symmetric cell and the direct conductivity measurement under compression. Moreover, the amount of binder and the diameter of the active material particles are increased and decreased numerically using an actual reconstructed electrode structure, and the effect of those structures on the effective conductivity is examined. The most dominant factors that degrade ionic conductivity are the binder distribution and the particle morphology, respectively, in the cathode and anode, and a correlation equation with the function of porosity is obtained. These values are compared with those obtained by theoretical model equations, and the difference between the current effective ionic conductivity and the physical limiting value is determined.

  3. Liquid electrode

    DOEpatents

    Ekechukwu, Amy A.

    1994-01-01

    A dropping electrolyte electrode for use in electrochemical analysis of non-polar sample solutions, such as benzene or cyclohexane. The liquid electrode, preferably an aqueous salt solution immiscible in the sample solution, is introduced into the solution in dropwise fashion from a capillary. The electrolyte is introduced at a known rate, thus, the droplets each have the same volume and surface area. The electrode is used in making standard electrochemical measurements in order to determine properties of non-polar sample solutions.

  4. Analyzing the Structure of Air Force Space Acquisitions

    DTIC Science & Technology

    2006-12-01

    51 viii III. CASE STUDY APPLICATION ...............................................................................53 A. CHAPTER...discussed throughout this research paper . Acquisition Arm is defined as the entity in charge of the acquisition of space assets and systems. Air...phase Evolutionary Acquisition or Single Step to Full Capability FRP Decision Review FOC LRIP/ IOT &E Design Readiness Review Pre-Systems Acquisition

  5. Method of bonding a conductive layer on an electrode of an electrochemical cell

    DOEpatents

    Bowker, Jeffrey C.; Singh, Prabhakar

    1989-01-01

    A dense, electronically conductive interconnection layer 26 is bonded onto a porous, tubular, electronically conductive air electrode structure 16, optionally supported by a ceramic support 22, by (A) providing an air electrode surface, (B) forming on a selected portion of the electrode surface 24, without the use of pressure, particles of LaCrO.sub.3 doped with an element selected from the group consisting of Sr, Mg, Ca, Ba, Co, and mixtures thereof, where the particles have a deposit on their surface comprising calcium oxide and chromium oxide; (C) heating the particles with the oxide surface deposit in an oxidizing atmosphere at from 1,300.degree. C. to 1,550.degree. C., without the application of pressure, to provide a dense, sintered, interconnection material 26 bonded to the air electrode 16, where calcium and chromium from the surface deposit are incorporated into the structure of the LaCrO.sub.3. A solid electrolyte layer 18 can be applied to the uncovered portion of the air electrode, and a fuel electrode 20 can be applied to the solid electrolyte, to provide an electrochemical cell 10.

  6. Method of bonding a conductive layer on an electrode of an electrochemical cell

    DOEpatents

    Bowker, J.C.; Singh, P.

    1989-08-29

    A dense, electronically conductive interconnection layer is bonded onto a porous, tubular, electronically conductive air electrode structure, optionally supported by a ceramic support, by (A) providing an air electrode surface, (B) forming on a selected portion of the electrode surface, without the use of pressure, particles of LaCrO[sub 3] doped with an element selected from the group consisting of Sr, Mg, Ca, Ba, Co, and mixtures thereof, where the particles have a deposit on their surface comprising calcium oxide and chromium oxide; (C) heating the particles with the oxide surface deposit in an oxidizing atmosphere at from 1,300 C to 1,550 C, without the application of pressure, to provide a dense, sintered, interconnection material bonded to the air electrode, where calcium and chromium from the surface deposit are incorporated into the structure of the LaCrO[sub 3]. A solid electrolyte layer can be applied to the uncovered portion of the air electrode, and a fuel electrode can be applied to the solid electrolyte, to provide an electrochemical cell. 4 figs.

  7. 78 FR 63169 - Meetings of the National Commission on the Structure of the Air Force; Cancellation of October 1...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-23

    ... Officer, National Commission on the Structure of the Air Force, 1950 Defense Pentagon Room 3A874... of the Secretary Meetings of the National Commission on the Structure of the Air Force; Cancellation..., 2013 meeting of the National Commission on the Structure of the Air Force in Bossier City,...

  8. Chemical and structural stability of lithium-ion battery electrode materials under electron beam.

    PubMed

    Lin, Feng; Markus, Isaac M; Doeff, Marca M; Xin, Huolin L

    2014-07-16

    The investigation of chemical and structural dynamics in battery materials is essential to elucidation of structure-property relationships for rational design of advanced battery materials. Spatially resolved techniques, such as scanning/transmission electron microscopy (S/TEM), are widely applied to address this challenge. However, battery materials are susceptible to electron beam damage, complicating the data interpretation. In this study, we demonstrate that, under electron beam irradiation, the surface and bulk of battery materials undergo chemical and structural evolution equivalent to that observed during charge-discharge cycling. In a lithiated NiO nanosheet, a Li2CO3-containing surface reaction layer (SRL) was gradually decomposed during electron energy loss spectroscopy (EELS) acquisition. For cycled LiNi(0.4)Mn(0.4)Co(0.18)Ti(0.02)O2 particles, repeated electron beam irradiation induced a phase transition from an layered structure to an rock-salt structure, which is attributed to the stoichiometric lithium and oxygen removal from 3a and 6c sites, respectively. Nevertheless, it is still feasible to preserve pristine chemical environments by minimizing electron beam damage, for example, using fast electron imaging and spectroscopy. Finally, the present study provides examples of electron beam damage on lithium-ion battery materials and suggests that special attention is necessary to prevent misinterpretation of experimental results.

  9. Electrode for electrochemical cell

    DOEpatents

    Kaun, T.D.; Nelson, P.A.; Miller, W.E.

    1980-05-09

    An electrode structure for a secondary electrochemical cell includes an outer enclosure defining a compartment containing electrochemical active material. The enclosure includes a rigid electrically conductive metal sheet with perforated openings over major side surfaces. The enclosure can be assembled as first and second trays each with a rigid sheet of perforated electrically conductive metal at major side surfaces and normally extending flanges at parametric margins. The trays can be pressed together with moldable active material between the two to form an expandable electrode. A plurality of positive and negative electrodes thus formed are arranged in an alternating array with porous frangible interelectrode separators within the housing of the secondary electrochemical cell.

  10. Electrode for electrochemical cell

    DOEpatents

    Kaun, Thomas D.; Nelson, Paul A.; Miller, William E.

    1981-01-01

    An electrode structure for a secondary electrochemical cell includes an outer enclosure defining a compartment containing electrochemical active material. The enclosure includes a rigid electrically conductive metal sheet with perforated openings over major side surfaces. The enclosure can be assembled as first and second trays each with a rigid sheet of perforated electrically conductive metal at major side surfaces and normally extending flanges at parametric margins. The trays can be pressed together with moldable active material between the two to form an expandable electrode. A plurality of positive and negative electrodes thus formed are arranged in an alternating array with porous frangible interelectrode separators within the housing of the secondary electrochemical cell.

  11. New approach for fabricating hybrid-structured metal mesh films for flexible transparent electrodes by the combination of electrospinning and metal deposition

    NASA Astrophysics Data System (ADS)

    Huh, Jin Woo; Lee, Dong Kyu; Jeon, Hwan-Jin; Ahn, Chi Won

    2016-11-01

    In this study, hybrid-structured metal mesh (HMM) films as potential flexible transparent electrodes, composed of aligned micro-sized metal fibers integrated into random network of metal nanofibers, were fabricated by the combination of electrospinning and metal deposition. These naturally fiber-bridged HMMs, with a gold layer thickness of 85 nm, exhibited a high transmittance of around 90% and a sheet resistance of approximately 10 Ω sq-1, as well as favorable mechanical stability under bending stress. These results demonstrate that the approach employed herein is a simple, highly efficient, and facile process for fabricating, uniform, interconnected fiber networks with potential for producing high-performance flexible transparent electrodes.

  12. New approach for fabricating hybrid-structured metal mesh films for flexible transparent electrodes by the combination of electrospinning and metal deposition.

    PubMed

    Huh, Jin Woo; Lee, Dong Kyu; Jeon, Hwan-Jin; Ahn, Chi Won

    2016-11-25

    In this study, hybrid-structured metal mesh (HMM) films as potential flexible transparent electrodes, composed of aligned micro-sized metal fibers integrated into random network of metal nanofibers, were fabricated by the combination of electrospinning and metal deposition. These naturally fiber-bridged HMMs, with a gold layer thickness of 85 nm, exhibited a high transmittance of around 90% and a sheet resistance of approximately 10 Ω sq(-1), as well as favorable mechanical stability under bending stress. These results demonstrate that the approach employed herein is a simple, highly efficient, and facile process for fabricating, uniform, interconnected fiber networks with potential for producing high-performance flexible transparent electrodes.

  13. 78 FR 78944 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-12-27

    ... Deterrence Operations, Command and Control, Personnel Recovery, Agile Combat Support, Training and Education... budgeting flexibility. 2. Impact of strategic choices on Air Force capabilities and force structure options... professional and technical education and shared experiences; b. Recognizing in promotion and...

  14. Square Wave Voltammetry of TNT at Gold Electrodes Modified with Self-Assembled Monolayers Containing Aromatic Structures

    PubMed Central

    Trammell, Scott A.; Zabetakis, Dan; Moore, Martin; Verbarg, Jasenka; Stenger, David A.

    2014-01-01

    Square wave voltammetry for the reduction of 2,4,6-trinitrotoluene (TNT) was measured in 100 mM potassium phosphate buffer (pH 8) at gold electrodes modified with self-assembled monolayers (SAMs) containing either an alkane thiol or aromatic ring thiol structures. At 15 Hz, the electrochemical sensitivity (µA/ppm) was similar for all SAMs tested. However, at 60 Hz, the SAMs containing aromatic structures had a greater sensitivity than the alkane thiol SAM. In fact, the alkane thiol SAM had a decrease in sensitivity at the higher frequency. When comparing the electrochemical response between simulations and experimental data, a general trend was observed in which most of the SAMs had similar heterogeneous rate constants within experimental error for the reduction of TNT. This most likely describes a rate limiting step for the reduction of TNT. However, in the case of the alkane SAM at higher frequency, the decrease in sensitivity suggests that the rate limiting step in this case may be electron tunneling through the SAM. Our results show that SAMs containing aromatic rings increased the sensitivity for the reduction of TNT when higher frequencies were employed and at the same time suppressed the electrochemical reduction of dissolved oxygen. PMID:25549081

  15. Nanoparticle-Mediated Physical Exfoliation of Aqueous-Phase Graphene for Fabrication of Three-Dimensionally Structured Hybrid Electrodes

    PubMed Central

    Lee, Younghee; Choi, Hojin; Kim, Min-Sik; Noh, Seonmyeong; Ahn, Ki-Jin; Im, Kyungun; Kwon, Oh Seok; Yoon, Hyeonseok

    2016-01-01

    Monodispersed polypyrrole (PPy) nanospheres were physically incorporated as guest species into stacked graphene layers without significant property degradation, thereby facilitating the formation of unique three-dimensional hybrid nanoarchitecture. The electrochemical properties of the graphene/particulate PPy (GPPy) nanohybrids were dependent on the sizes and contents of the PPy nanospheres. The nanohybrids exhibited optimum electrochemical performance in terms of redox activity, charge-transfer resistance, and specific capacitance at an 8:1 PPy/graphite (graphene precursor) weight ratio. The packing density of the alternately stacked nanohybrid structure varied with the nanosphere content, indicating the potential for high volumetric capacitance. The nanohybrids also exhibited good long-term cycling stability because of a structural synergy effect. Finally, fabricated nanohybrid-based flexible all–solid state capacitor cells exhibited good electrochemical performance in an acidic electrolyte with a maximum energy density of 8.4 Wh kg−1 or 1.9 Wh L−1 at a maximum power density of 3.2 kW kg−1 or 0.7 kW L−1; these performances were based on the mass or packing density of the electrode materials. PMID:26813878

  16. The interaction of consecutive process steps in the manufacturing of lithium-ion battery electrodes with regard to structural and electrochemical properties

    NASA Astrophysics Data System (ADS)

    Bockholt, Henrike; Indrikova, Maira; Netz, Andreas; Golks, Frederik; Kwade, Arno

    2016-09-01

    The individual steps in the electrode manufacturing process, e.g., conductive additives addition, mixing, and calendering, strongly affect the electrochemical and mechanical properties of the electrodes. LiNi1/3Co1/3Mn1/3O2 (NCM) cathode electrodes with conductive additive variations are fabricated using a reference and an intensive mixing process, and are subsequently calendered to different porosities. It is found that graphite reduces the pore size of NCM electrodes, in contrast to the carbon black that establishes additional nanoscale pores. Electrodes manufactured with reference mixing result in a porous carbon black network with good overall electric pathways, whereas those manufactured with intensive processing result in a dense carbon black network, leading to good short-range contacts, but a lack of long-range contacts. In this case, the addition of graphite as a conductive additive is identified to establish important additional long-range contacts. Due to the structural differences achieved by the compared processing routes, the calendering process can have a positive or negative impact on battery performance.

  17. Oxide/ metal/oxide nanolaminate structures for application of transparent electrodes

    NASA Astrophysics Data System (ADS)

    Dikov, Hr; Ivanova, T.; Vitanov, P.

    2016-10-01

    Transparent and conductive oxide/ metal/ oxide nanolaminate structures were deposited on glass and polymer substrate by RF magnetron sputtering without substrate heating. The Ag nanoparticles with different size and distance between neighboring particles were located on the interface of two thin oxide layers. This sputtering configuration allows obtaining thin films with homogeneous thickness. The three targets give the opportunity to deposit successively three different layers without opening the chamber. The developed process for transparent conducting coating is a low temperature and it is suitable for application on organic materials as substrate and foils. The experiment with different substrates manifest that the optical transparency of the conducting coating depends on substrate material. The obtained results have demonstrated that the nanolaminate structures oxide/metal/oxide (OMO) as TCO coating are especially suitable for applications in flexible electronics and optoelectronics

  18. First-principles study of the structure of water layers on flat and stepped Pb electrodes

    PubMed Central

    Lin, Xiaohang; Evers, Ferdinand

    2016-01-01

    Summary On the basis of perodic density functional theory (DFT) calculations, we have addressed the geometric structures and electronic properties of water layers on flat and stepped Pb surfaces. In contrast to late d-band metals, on Pb(111) the energy minimum structure does not correspond to an ice-like hexagonal arrangement at a coverage of 2/3, but rather to a distorted structure at a coverage of 1 due to the larger lattice constant of Pb. At stepped Pb surfaces, the water layers are pinned at the step edge and form a complex network consisting of rectangles, pentagons and hexagons. The thermal stability of the water layers has been studied by using ab initio molecular dynamics simulations (AIMD) at a temperature of 140 K. Whereas the water layer on Pb(111) is already unstable at this temperature, the water layers on Pb(100), Pb(311), Pb(511) and Pb(711) exhibit a higher stability because of stronger water–water interactions. The vibrational spectra of the water layers at the stepped surfaces show a characteristic splitting into three modes in the O–H stretch region. PMID:27335744

  19. Prediction of Human Blood: Air Partition Coefficient: A Comparison of Structure-Based and Property-Based Methods

    DTIC Science & Technology

    2007-11-02

    models developed using experimental properties, including saline;air partition coefficient (longP saline;air) and olive oil ;air partition coefficient...logP olive oil ;air), as independent variables, indicating that the structure-property correlations are comparable to the property-property

  20. Fabrication of a smart air intake structure using shape memory alloy wire embedded composite

    NASA Astrophysics Data System (ADS)

    Jung, Beom-Seok; Kim, Min-Saeng; Kim, Ji-Soo; Kim, Yun-Mi; Lee, Woo-Yong; Ahn, Sung-Hoon

    2010-05-01

    Shape memory alloys (SMAs) have been actively studied in many fields utilizing their high energy density. Applying SMA wire-embedded composite to aerospace structures, such as air intake of jet engines and guided missiles, is attracting significant attention because it could generate a comparatively large actuating force. In this research, a scaled structure of SMA wire-embedded composite was fabricated for the air intake of aircraft. The structure was composed of several prestrained Nitinol (Ni-Ti) SMA wires embedded in ∩-shape glass fabric reinforced plastic (GFRP), and it was cured at room temperature for 72 h. The SMA wire-embedded GFRP could be actuated by applying electric current through the embedded SMA wires. The activation angle generated from the composite structure was large enough to make a smart air intake structure.

  1. Air Force Astronautics Laboratory smart structures and skins program overview

    NASA Astrophysics Data System (ADS)

    Dehart, Douglas W.

    1990-02-01

    The smart structure/skins systems envisioned by the USAF Astronautics Laboratory for such future spacecraft as the Space Based Radar and Space Based Laser will employ embedded sensors, actuators, and microprocessors to sense, evaluate, and damp, all natural and spurious vibrations; the health-monitoring system also figured by the smart structure will sense any deterioration of structural soundness. Fiber-optics constitutes the sensor technology of choice, due to its lightness, immunity to EM interference, and easy incorporation into composite materials.

  2. Role of precursor crystal structure on electrochemical performance of carbide-derived carbon electrodes

    NASA Astrophysics Data System (ADS)

    Palazzo, Benjamin; Norris, Zach; Taylor, Greg; Yu, Lei; Lofland, Samuel; Hettinger, Jeffrey

    2015-03-01

    Binary carbides with hexagonal and cubic crystal structures have been synthesized by reactive magnetron sputtering of vanadium and other transition metals in acetylene or methane gas mixed with argon. The binary carbides are converted to carbide-derived carbon (CDC) films using chlorine gas in a post-deposition process in an external vacuum reaction furnace. Residual chlorine has been removed using an annealing step in a hydrogen atmosphere. The CDC materials have been characterized by x-ray diffraction, x-ray fluorescence, and scanning electron microscopy. The performance of the CDC materials in electrochemical device applications has been measured with the hexagonal phase precursor demonstrating a significantly higher specific capacitance in comparison to that of the cubic phase. We report these results and pore-size distributions of these and similar materials.

  3. Comprehensive insights into the structural and chemical changes in mixed-anion FeOF electrodes by using operando PDF and NMR spectroscopy.

    PubMed

    Wiaderek, Kamila M; Borkiewicz, Olaf J; Castillo-Martínez, Elizabeth; Robert, Rosa; Pereira, Nathalie; Amatucci, Glenn G; Grey, Clare P; Chupas, Peter J; Chapman, Karena W

    2013-03-13

    In-depth analysis of operando X-ray pair distribution function (PDF) data is combined with Li NMR spectroscopy to gain comprehensive insights into the electrochemical reaction mechanism of high-performance iron oxyfluoride electrodes. While the full discharge capacity could be recovered upon charge, implying reversibility of the electrochemical reaction, the atomic structure of the electrode formed after cycling (discharge-charge) differs from the pristine uncycled electrode material. Instead, the "active" electrode that forms upon cycling is a nanocomposite of an amorphous rutile phase and a nanoscale rock salt phase. Bond valence sum analysis, based on the precise structural parameters (bond lengths and coordination number) extracted from the in situ PDF data, suggests that anion partitioning occurs during the electrochemical reaction, with the rutile phase being F-rich and the rock salt phase being O-rich. The F- and O-rich phases react sequentially; Fe in a F-rich environment reacts preferentially during both discharge and charge.

  4. Investigating the depth electrode-brain interface in deep brain stimulation using finite element models with graded complexity in structure and solution.

    PubMed

    Yousif, Nada; Liu, Xuguang

    2009-10-30

    Deep brain stimulation (DBS) is an increasingly used surgical therapy for a range of neurological disorders involving the long-term electrical stimulation of various regions of the human brain in a disorder specific manner. Despite being used for the last 20 years, the underlying mechanisms are still not known, and disputed. In particular, when the electrodes are implanted into the human brain, an interface is created with changing biophysical properties which may impact on stimulation. We previously defined the electrode-brain interface (EBI) as consisting of three structural elements: the quadripolar DBS electrode, the peri-electrode space and the surrounding brain tissue. In order to understand more about the nature of this EBI, we used structural computational models of this interface, and estimated the effects of stimulation using coupled axon models. These finite element models differ in complexity, each highlighting a different feature of the EBI's effect on the DBS-induced electric field. We show that the quasi-static models are sufficient to demonstrate the difference between the acute and chronic clinical stages post-implantation. However, the frequency-dependent models are necessary as the waveform shaping has a major influence on the activation of neuronal fibres. We also investigate anatomical effects on the electric field, by taking specific account of the ventricular system in the human brain. Taken together, these models allow us to visualise the static, dynamic and target specific properties of the DBS-induced field in the surrounding brain regions.

  5. Nano-sized structured layered positive electrode materials to enable high energy density and high rate capability lithium batteries

    DOEpatents

    Deng, Haixia; Belharouak, Ilias; Amine, Khalil

    2012-10-02

    Nano-sized structured dense and spherical layered positive active materials provide high energy density and high rate capability electrodes in lithium-ion batteries. Such materials are spherical second particles made from agglomerated primary particles that are Li.sub.1+.alpha.(Ni.sub.xCo.sub.yMn.sub.z).sub.1-tM.sub.tO.sub.2-dR.sub.d- , where M is selected from can be Al, Mg, Fe, Cu, Zn, Cr, Ag, Ca, Na, K, In, Ga, Ge, V, Mo, Nb, Si, Ti, Zr, or a mixture of any two or more thereof, R is selected from F, Cl, Br, I, H, S, N, or a mixture of any two or more thereof, and 0.ltoreq..alpha..ltoreq.0.50; 0

  6. Framework structured Na4Mn4Ti5O18 as an electrode for Na-ion storage hybrid devices.

    PubMed

    Jayakumar, M; Hemalatha, K; Ramesha, K; Prakash, A S

    2015-08-28

    In this study, framework structured Na4Mn4Ti5O18 possessing S-shaped tunnels for sodium intercalation is reported as an electrode for hybrid sodium ion batteries. Galvanostatic cycling of Na4Mn4Ti5O18vs. Na in the voltage region from 1.5 V to 3.95 V exhibits a capacity of 102 mA h g(-1) at 0.1C rate corresponding to a specific capacitance of 149 F g(-1) with a capacity retention of 90% over 50 cycles. The electrochemical analysis using CV measurements revealed the charge storage involving intercalation and pseudocapacitance. For instance, total charge storage of 345 C g(-1) is observed at 0.01 mV s(-1), which is attributed to 63% intercalation and 37% capacitance. Na4Mn4Ti5O18 was also studied for sodium ion storage in an aqueous medium. It delivered a capacity of 36 mA h g(-1) (144 F g(-1)) in the voltage window of 0-0.8 V.

  7. Liquid crystal-gated-organic field-effect transistors with in-plane drain-source-gate electrode structure.

    PubMed

    Seo, Jooyeok; Nam, Sungho; Jeong, Jaehoon; Lee, Chulyeon; Kim, Hwajeong; Kim, Youngkyoo

    2015-01-14

    We report planar liquid crystal-gated-organic field-effect transistors (LC-g-OFETs) with a simple in-plane drain-source-gate electrode structure, which can be cost-effectively prepared by typical photolithography/etching processes. The LC-g-OFET devices were fabricated by forming the LC layer (4-cyano-4'-pentylbiphenyl, 5CB) on top of the channel layer (poly(3-hexylthiophene), P3HT) that was spin-coated on the patterned indium-tin oxide (ITO)-coated glass substrates. The LC-g-OFET devices showed p-type transistor characteristics, while a current saturation behavior in the output curves was achieved for the 50-150 nm-thick P3HT (channel) layers. A prospective on/off ratio (>1 × 10(3)) was obtained regardless of the P3HT thickness, whereas the resulting hole mobility (0.5-1.1 cm(2)/(V s)) at a linear regime was dependent on the P3HT thickness. The tilted ordering of 5CB at the LC-P3HT interfaces, which is induced by the gate electric field, has been proposed as a core point of working mechanism for the present LC-g-OFETs.

  8. Dielectric and magnetic characterizations of capacitor structures with an ionic liquid/MgO barrier and a ferromagnetic Pt electrode

    NASA Astrophysics Data System (ADS)

    Hayakawa, D.; Obinata, A.; Miwa, K.; Ono, S.; Hirai, T.; Koyama, T.; Chiba, D.

    2016-11-01

    The dielectric and magnetic properties of electric double layer (EDL) capacitor structures with a perpendicularly magnetized Pt/Co/Pt electrode and an insulating cap layer (MgO) are investigated. An electric field is applied through a mixed ionic liquid/MgO barrier to the surface of the top Pt layer, at which the magnetic moment is induced by the ferromagnetic proximity effect. The basic dielectric properties of the EDL capacitor are studied by varying the thickness of the MgO cap layer. The results indicate that the capacitance, i.e., the accumulated charge density at the Pt surface, is reduced with increasing the MgO thickness. From the MgO thickness dependence of the capacitance value, the effective dielectric constant of the ionic liquid is evaluated. Almost no electric field effect on the magnetic moment, the coercivity, or the Curie temperature is confirmed in the top Pt layer with the thickness of 1.3 nm, regardless of the presence or absence of the MgO cap layer, whereas the a clear change in the magnetic moment is observed when the top Pt layer is replaced by a Pd layer of 1.7 nm.

  9. Liquid electrode

    DOEpatents

    Ekechukwu, A.A.

    1994-07-05

    A dropping electrolyte electrode is described for use in electrochemical analysis of non-polar sample solutions, such as benzene or cyclohexane. The liquid electrode, preferably an aqueous salt solution immiscible in the sample solution, is introduced into the solution in dropwise fashion from a capillary. The electrolyte is introduced at a known rate, thus, the droplets each have the same volume and surface area. The electrode is used in making standard electrochemical measurements in order to determine properties of non-polar sample solutions. 2 figures.

  10. [Structure and functioning of research ethics committees in the Autonomous City of Buenos Aires and Greater Buenos Aires].

    PubMed

    Sabio, María Fernanda; Bortz, Jaime Elías

    2015-06-01

    Given the few existing studies on research ethics committees (RECs) in Argentina, this paper aims to describe the structure and functioning of institutional RECs in the Autonomous City of Buenos Aires and Greater Buenos Aires. A descriptive, qualitative and quantitative research study was carried out using a survey conducted between March and July 2012. The sample was made up of 46 RECs. Forty percent of committee members were doctors and the age and sex distribution met standards. Inadequate numbers of methodologists, community representatives, lawyers and members external to the institution were identified, as well as shortcomings regarding administrative staff, fixed locations for meetings, budgets adequate to expenditures and training in research ethics. Some of those surveyed reported problems in their relationship with the institution and with researchers, in addition to difficulties regarding the time available to perform tasks.

  11. Application of air-coupled acoustic thermography (ACAT) for inspection of honeycomb sandwich structures

    NASA Astrophysics Data System (ADS)

    Zalameda, Joseph N.; Winfree, William P.; Pergantis, Charles G.; DeSchepper, Daniel; Flanagan, David

    2009-05-01

    The application of a noncontact air coupled acoustic heating technique is investigated for the inspection of advanced honeycomb composite structures. A weakness in the out of plane stiffness of the structure, caused by a delamination or core damage, allows for the coupling of acoustic energy and thus this area will have a higher temperature than the surrounding area. Air coupled acoustic thermography (ACAT) measurements were made on composite sandwich structures with damage and were compared to conventional flash thermography. A vibrating plate model is presented to predict the optimal acoustic source frequency. Improvements to the measurement technique are also discussed.

  12. Application of Air Coupled Acoustic Thermography (ACAT) for Inspection of Honeycomb Sandwich Structures

    NASA Technical Reports Server (NTRS)

    Winfree, William P.; Zalameda, Joseph N.; Pergantis, Charles; Flanagan, David; Deschepper, Daniel

    2009-01-01

    The application of a noncontact air coupled acoustic heating technique is investigated for the inspection of advanced honeycomb composite structures. A weakness in the out of plane stiffness of the structure, caused by a delamination or core damage, allows for the coupling of acoustic energy and thus this area will have a higher temperature than the surrounding area. Air coupled acoustic thermography (ACAT) measurements were made on composite sandwich structures with damage and were compared to conventional flash thermography. A vibrating plate model is presented to predict the optimal acoustic source frequency. Improvements to the measurement technique are also discussed.

  13. Vertical Moist Thermodynamic Structure and Spatial-Temporal Evolution of the MJO in AIRS Observations

    NASA Technical Reports Server (NTRS)

    Tian, Baijun; Waliser, Duane E.; Fetzer, Eric J.; Lambrigtsen, Bjorn H.; Yung, Yuk L.; Wang, Bin

    2006-01-01

    The atmospheric moisture and temperature profiles from the Atmospheric Infrared Sounder (AIRS)/Advanced Microwave Sounding Unit on the NASA Aqua mission, in combination with the precipitation from the Tropical Rainfall Measuring Mission (TRMM), are employed to study the vertical moist thermodynamic structure and spatial-temporal evolution of the Madden-Julian oscillation (MJO). The AIRS data indicate that, in the Indian Ocean and western Pacific, the temperature anomaly exhibits a trimodal vertical structure: a warm (cold) anomaly in the free troposphere (800-250 hPa) and a cold (warm) anomaly near the tropopause (above 250 hPa) and in the lower troposphere (below 800 hPa) associated with enhanced (suppressed) convection. The AIRS moisture anomaly also shows markedly different vertical structures as a function of longitude and the strength of convection anomaly. Most significantly, the AIRS data demonstrate that, over the Indian Ocean and western Pacific, the enhanced (suppressed) convection is generally preceded in both time and space by a low-level warm and moist (cold and dry) anomaly and followed by a low-level cold and dry (warm and moist) anomaly. The MJO vertical moist thermodynamic structure from the AIRS data is in general agreement, particularly in the free troposphere, with previous studies based on global reanalysis and limited radiosonde data. However, major differences in the lower-troposphere moisture and temperature structure between the AIRS observations and the NCEP reanalysis are found over the Indian and Pacific Oceans, where there are very few conventional data to constrain the reanalysis. Specifically, the anomalous lower-troposphere temperature structure is much less well defined in NCEP than in AIRS for the western Pacific, and even has the opposite sign anomalies compared to AIRS relative to the wet/dry phase of the MJO in the Indian Ocean. Moreover, there are well-defined eastward-tilting variations of moisture with height in AIRS over the

  14. The structure of PccH from Geobacter sulfurreducens - a novel low reduction potential monoheme cytochrome essential for accepting electrons from an electrode.

    PubMed

    Dantas, Joana M; Campelo, Luísa M; Duke, Norma E C; Salgueiro, Carlos A; Pokkuluri, P Raj

    2015-06-01

    The structure of cytochrome c (GSU3274) designated as PccH from Geobacter sulfurreducens was determined at a resolution of 2.0 Å. PccH is a small (15 kDa) cytochrome containing one c-type heme, found to be essential for the growth of G. sulfurreducens with respect to accepting electrons from graphite electrodes poised at -300 mV versus standard hydrogen electrode. with fumarate as the terminal electron acceptor. The structure of PccH is unique among the monoheme cytochromes described to date. The structural fold of PccH can be described as forming two lobes with the heme sandwiched in a cleft between the two lobes. In addition, PccH has a low reduction potential of -24 mV at pH 7, which is unusual for monoheme cytochromes. Based on difference in structure, together with sequence phylogenetic analysis, we propose that PccH can be regarded as a first characterized example of a new subclass of class I monoheme cytochromes. The low reduction potential of PccH may enable the protein to be redox active at the typically negative potential ranges encountered by G. sulfurreducens. Because PccH is predicted to be located in the periplasm of this bacterium, it could not be involved in the first step of accepting electrons from the electrode but is very likely involved in the downstream electron transport events in the periplasm.

  15. The structure of PccH from Geobactersulfurreducens-a novel low reduction potential monoheme cytochrome essential for accepting electrons from an electrode

    SciTech Connect

    Dantas, Joana; Campelo, Luisa M.; Duke, Norma E. C.; Salgueiro, Carlos A.; Pokkuluri, P. Raj

    2015-06-01

    The structure of cytochrome c (GSU3274) designated as PccH from Geobactersulfurreducens was determined at a resolution of 2.0 angstrom. PccH is a small (15kDa) cytochrome containing one c-type heme, found to be essential for the growth of G.sulfurreducens with respect to accepting electrons from graphite electrodes poised at -300mV versus standard hydrogen electrode. with fumarate as the terminal electron acceptor. The structure of PccH is unique among the monoheme cytochromes described to date. The structural fold of PccH can be described as forming two lobes with the heme sandwiched in a cleft between the two lobes. In addition, PccH has a low reduction potential of -24mV at pH7, which is unusual for monoheme cytochromes. Based on difference in structure, together with sequence phylogenetic analysis, we propose that PccH can be regarded as a first characterized example of a new subclass of class I monoheme cytochromes. The low reduction potential of PccH may enable the protein to be redox active at the typically negative potential ranges encountered by G. sulfurreducens. Because PccH is predicted to be located in the periplasm of this bacterium, it could not be involved in the first step of accepting electrons from the electrode but is very likely involved in the downstream electron transport events in the periplasm.

  16. Development of Micro Air Vehicle Technology With In-Flight Adaptive-Wing Structure

    NASA Technical Reports Server (NTRS)

    Waszak, Martin R. (Technical Monitor); Shkarayev, Sergey; Null, William; Wagner, Matthew

    2004-01-01

    This is a final report on the research studies, "Development of Micro Air Vehicle Technology with In-Flight Adaptrive-Wing Structure". This project involved the development of variable-camber technology to achieve efficient design of micro air vehicles. Specifically, it focused on the following topics: 1) Low Reynolds number wind tunnel testing of cambered-plate wings. 2) Theoretical performance analysis of micro air vehicles. 3) Design of a variable-camber MAV actuated by micro servos. 4) Test flights of a variable-camber MAV.

  17. Experimental investigation of the structure of supersonic two-dimensional air microjets

    NASA Astrophysics Data System (ADS)

    Timofeev, Ivan; Aniskin, Vladimir; Mironov, Sergey

    2016-10-01

    We have experimentally studied the structure of supersonic underexpanded room-temperature air jets escaping from micronozzles with characteristic heights from 47 to 175 µm and widths within 2410-3900 µm in a range of Reynolds numbers of 1280-9460. The dimensions of the first shock cell are established. The supersonic core length of supersonic underexpanded air jets has been determined for the first time. A flow regime with a large supersonic core length has observed for air jets escaping from a 47µm high nozzle.

  18. Compressor-fan unitary structure for air conditioning system

    NASA Astrophysics Data System (ADS)

    Dreiman, N.

    2015-08-01

    An extremely compact, therefore space saving unitary structure of short axial length is produced by radial integration of a revolving piston rotary compressor and an impeller of a centrifugal fan. The unitary structure employs single motor to run as the compressor so the airflow fan and eliminates duality of motors, related power supply and control elements. Novel revolving piston rotary compressor which provides possibility for such integration comprises the following: a suction gas delivery system which provides cooling of the motor and supplies refrigerant into the suction chamber under higher pressure (supercharged); a modified discharge system and lubricating oil supply system. Axial passages formed in the stationary crankshaft are used to supply discharge gas to a condenser, to return vaporized cooling agent from the evaporator to the suction cavity of the compressor, to pass a lubricant and to accommodate wiring supplying power to the unitary structure driver -external rotor electric motor.

  19. Structural changes of the KcsA potassium channel upon application of the electrode potential studied by surface-enhanced IR absorption spectroscopy

    NASA Astrophysics Data System (ADS)

    Yamakata, Akira; Shimizu, Hirofumi; Osawa, Masatoshi; Oiki, Shigetoshi

    2013-06-01

    Structural changes of the KcsA potassium channel fixed on gold electrode surface in the upright orientation were studied by surface-enhanced IR absorption spectroscopy (SEIRAS). Measurements were performed at neutral pH, where the activation gate is kept closed. Band intensities were enhanced for the asymmetric (1565 cm-1) and symmetric (1405 cm-1) OCO-carboxylate groups at negative electrode potentials in the K+ solution, but not in the Na+ solution. Even for the reverse-oriented channel, the enhanced OCO-carboxylate band was evident at negative potential. When TBA was loaded in the central cavity, the K+-specific OCO band was not elicited. These results indicate that the negative electrode potential renders the local K+ concentration accumulated at the vicinity of the electrode surface, and the KcsA channel bathed in high K+ changes conformation of the selectivity filter from the collapsed to the open, and OCO-carboxylate groups (D80 and E71) in the back of the filter were rearranged.

  20. Influence of the structure of the anion in an ionic liquid electrolyte on the electrochemical performance of a silicon negative electrode for a lithium-ion battery

    NASA Astrophysics Data System (ADS)

    Yamaguchi, Kazuki; Domi, Yasuhiro; Usui, Hiroyuki; Shimizu, Masahiro; Matsumoto, Kuninobu; Nokami, Toshiki; Itoh, Toshiyuki; Sakaguchi, Hiroki

    2017-01-01

    We investigated the influence of the anions in ionic liquid electrolytes on the electrochemical performance of a silicon (Si) negative electrode for a lithium-ion battery. While the electrode exhibited poor cycle stability in tetrafluoroborate-based and propylene carbonate-based electrolytes, better cycle performance was achieved in bis(fluorosulfonyl)amide (FSA-)- and bis(trifluoromethanesulfonyl)amide (TFSA-)-based electrolytes, in which the discharge capacity of a Si electrode was more than 1000 mA h g-1 at the 100th cycle. It is considered that a surface film derived from FSA-- and TFSA--based electrolytes effectively suppressed continuous decomposition of the electrolyte. In a capacity limitation test, a discharge capacity of 1000 mA h g-1 was maintained even after about the 1600th cycle in the FSA--based electrolyte, which corresponds to a cycle life almost twice as long as that in TFSA--based electrolyte. This result should be explained by the high structural stability of FSA--derived surface film. In addition, better rate capability with a discharge capacity of 700 mA h g-1 was obtained at a high current rate of 6 C (21 A g-1) in FSA--based electrolyte, which was 7-fold higher than that in TFSA--based electrolyte. These results clarified that FSA--based ionic liquid electrolyte is the most promising candidate for Si-based negative electrodes.

  1. Method for fabrication of electrodes

    DOEpatents

    Jankowski, Alan F.; Morse, Jeffrey D.; Barksdale, Randy

    2004-06-22

    Described herein is a method to fabricate porous thin-film electrodes for fuel cells and fuel cell stacks. Furthermore, the method can be used for all fuel cell electrolyte materials which utilize a continuous electrolyte layer. An electrode layer is deposited on a porous host structure by flowing gas (for example, Argon) from the bottomside of the host structure while simultaneously depositing a conductive material onto the topside of the host structure. By controlling the gas flow rate through the pores, along with the process conditions and deposition rate of the thin-film electrode material, a film of a pre-determined thickness can be formed. Once the porous electrode is formed, a continuous electrolyte thin-film is deposited, followed by a second porous electrode to complete the fuel cell structure.

  2. Mediation pathways and effects of green structures on respiratory mortality via reducing air pollution

    PubMed Central

    Shen, Yu-Sheng; Lung, Shih-Chun Candice

    2017-01-01

    Previous studies have shown both health and environmental benefits of green spaces, especially in moderating temperature and reducing air pollution. However, the characteristics of green structures have been overlooked in previous investigations. In addition, the mediation effects of green structures on respiratory mortality have not been assessed. This study explores the potential mediation pathways and effects of green structure characteristics on respiratory mortality through temperature, primary and secondary air pollutants separately using partial least squares model with data from Taiwan. The measurable characteristics of green structure include the largest patch percentage, landscape proportion, aggregation, patch distance, and fragmentation. The results showed that mortality of pneumonia and chronic lower respiratory diseases could be reduced by minimizing fragmentation and increasing the largest patch percentage of green structure, and the mediation effects are mostly through reducing air pollutants rather than temperature. Moreover, a high proportion of but fragmented green spaces would increase secondary air pollutants and enhance health risks; demonstrating the deficiency of traditional greening policy with primary focus on coverage ratio. This is the first research focusing on mediation effects of green structure characteristics on respiratory mortality, revealing that appropriate green structure planning can be a useful complementary strategy in environmental health management. PMID:28230108

  3. Mediation pathways and effects of green structures on respiratory mortality via reducing air pollution

    NASA Astrophysics Data System (ADS)

    Shen, Yu-Sheng; Lung, Shih-Chun Candice

    2017-02-01

    Previous studies have shown both health and environmental benefits of green spaces, especially in moderating temperature and reducing air pollution. However, the characteristics of green structures have been overlooked in previous investigations. In addition, the mediation effects of green structures on respiratory mortality have not been assessed. This study explores the potential mediation pathways and effects of green structure characteristics on respiratory mortality through temperature, primary and secondary air pollutants separately using partial least squares model with data from Taiwan. The measurable characteristics of green structure include the largest patch percentage, landscape proportion, aggregation, patch distance, and fragmentation. The results showed that mortality of pneumonia and chronic lower respiratory diseases could be reduced by minimizing fragmentation and increasing the largest patch percentage of green structure, and the mediation effects are mostly through reducing air pollutants rather than temperature. Moreover, a high proportion of but fragmented green spaces would increase secondary air pollutants and enhance health risks; demonstrating the deficiency of traditional greening policy with primary focus on coverage ratio. This is the first research focusing on mediation effects of green structure characteristics on respiratory mortality, revealing that appropriate green structure planning can be a useful complementary strategy in environmental health management.

  4. Mediation pathways and effects of green structures on respiratory mortality via reducing air pollution.

    PubMed

    Shen, Yu-Sheng; Lung, Shih-Chun Candice

    2017-02-23

    Previous studies have shown both health and environmental benefits of green spaces, especially in moderating temperature and reducing air pollution. However, the characteristics of green structures have been overlooked in previous investigations. In addition, the mediation effects of green structures on respiratory mortality have not been assessed. This study explores the potential mediation pathways and effects of green structure characteristics on respiratory mortality through temperature, primary and secondary air pollutants separately using partial least squares model with data from Taiwan. The measurable characteristics of green structure include the largest patch percentage, landscape proportion, aggregation, patch distance, and fragmentation. The results showed that mortality of pneumonia and chronic lower respiratory diseases could be reduced by minimizing fragmentation and increasing the largest patch percentage of green structure, and the mediation effects are mostly through reducing air pollutants rather than temperature. Moreover, a high proportion of but fragmented green spaces would increase secondary air pollutants and enhance health risks; demonstrating the deficiency of traditional greening policy with primary focus on coverage ratio. This is the first research focusing on mediation effects of green structure characteristics on respiratory mortality, revealing that appropriate green structure planning can be a useful complementary strategy in environmental health management.

  5. Sound transmission through finite lightweight multilayered structures with thin air layers.

    PubMed

    Dijckmans, A; Vermeir, G; Lauriks, W

    2010-12-01

    The sound transmission loss (STL) of finite lightweight multilayered structures with thin air layers is studied in this paper. Two types of models are used to describe the vibro-acoustic behavior of these structures. Standard transfer matrix method assumes infinite layers and represents the plane wave propagation in the layers. A wave based model describes the direct sound transmission through a rectangular structure placed between two reverberant rooms. Full vibro-acoustic coupling between rooms, plates, and air cavities is taken into account. Comparison with double glazing measurements shows that this effect of vibro-acoustic coupling is important in lightweight double walls. For infinite structures, structural damping has no significant influence on STL below the coincidence frequency. In this frequency region, the non-resonant transmission or so-called mass-law behavior dominates sound transmission. Modal simulations suggest a large influence of structural damping on STL. This is confirmed by experiments with double fiberboard partitions and sandwich structures. The results show that for thin air layers, the damping induced by friction and viscous effects at the air gap surfaces can largely influence and improve the sound transmission characteristics.

  6. Rutile-structured TiO{sub 2} deposited by plasma enhanced atomic layer deposition using tetrakis(dimethylamino)titanium precursor on in-situ oxidized Ru electrode

    SciTech Connect

    Pointet, John; Gonon, Patrice; Latu-Romain, Lawrence; Bsiesy, Ahmad Vallée, Christophe

    2014-01-15

    In this work, tetrakis(dimethylamino)titanium precursor as well as in-situ oxidized ruthenium bottom electrode were used to grow rutile-structured titanium dioxide thin layers by plasma enhanced atomic layer deposition. Metal–insulator–metal capacitors have been elaborated in order to study the electrical properties of the device. It is shown that this process leads to devices exhibiting excellent results in terms of dielectric constant and leakage current.

  7. Improvement in color properties of copper mesh electrodes via electrophoretic coating with nano-structured carbon materials

    NASA Astrophysics Data System (ADS)

    Hwang, Young-Jin; Kim, Bu-Jong; Park, Jin-Seok

    2017-03-01

    In this study, the effects of coating with nano-structured carbon materials, such as carbon nanotube (CNT) and graphene, on the characteristics of transparent conductive electrodes based on copper (Cu) meshes, particularly on the visibility related to their color properties, were examined. The electrical sheet resistance of the Cu meshes remained almost unchanged regardless of the coating with CNT and graphene. Through the electrophoretic deposition method, the CNT and graphene layers were selectively used to coat only the regions where Cu mesh patterns had been formed, which helped minimize the transmittance loss caused by the coating with CNT and graphene. The reflectance of the Cu mesh was substantially reduced by the coating with CNT and graphene, meaning that the CNT or graphene coating layer played the role of suppressing the visible light reflected from the Cu mesh. In addition, the reflectance reduction effect was greater when the Cu mesh was coated with CNT rather than with graphene, which was attributed to the difference in particle size between the CNT suspension and the graphene suspension. Furthermore, the chromatic parameters (e.g., redness, yellowness) of the Cu meshes approached almost zero as the thickness of the CNT or graphene coating layer increased, meaning that the Cu meshes became nearly colorless, while the primitive Cu mesh was tinged with a red-orange color. The experiment results presented in this study verified that the combined technology with CNT and graphene coating contributed to the amelioration of the poor visibility caused by the high reflectance and color-tinted nature of the conventional Cu mesh.

  8. In situ X-ray absorption fine structure studies of a manganese dioxide electrode in a rechargeable MnO{sub 2}/Zn alkaline battery environment

    SciTech Connect

    Mo, Y.; Hu, Y.; Bae, I.T.; Miller, B.; Scherson, D.A.; Antonio, M.R.

    1996-12-31

    Electronic and structural aspects of a MnO{sub 2} electrode in a rechargeable MnO{sub 2}/Zn battery environment have been investigated by in situ Mn K-edge X-ray absorption fine structure (XAFS). The relative amplitudes of the three major Fourier transform shells of the EXAFS (extended XAFS) function of the rechargeable MnO{sub 2} electrode in the undischarged state were found to be similar to those found for ramsdellite, a MnO{sub 2} polymorph with substantial corner-sharing linkages among the basic MnO{sub 6} octahedral units. The analyses of the background-subtracted pre-edge peaks and absorption edge regions for the nominally 1-e{sup {minus}} discharged electrode were consistent with Mn{sup 3+} as being the predominant constituent species, rather than a mixture of Mn{sup 4+} and Mn{sup 2+} sites. Furthermore, careful inspection of both the XANES (X-ray absorption near edge structure) and EXAFS indicated that the full recharge of MnO, which had been previously discharged either by a 1- or 2-equivalent corner-sharing linkages compared to the original undischarged MnO{sub 2}.

  9. A sandwich structured SiO(2)/cytochrome c/SiO(2) on a boron-doped diamond film electrode as an electrochemical nitrite biosensor.

    PubMed

    Geng, Rong; Zhao, Guohua; Liu, Meichuan; Li, Mingfang

    2008-06-01

    A novel sandwich structured SiO(2) gel/cytochrome c (Cyt c)/SiO(2) gel was designed and constructed on conductive boron-doped diamond (BDD) film substrate. A SiO(2) gel membrane was first in situ deposited on the pretreated positive charged H-terminated BDD electrode with a simple and artful surface vapor sol-gel method. Cyt c was subsequently immobilized onto the SiO(2) membranes by electrostatic attraction, followed by another SiO(2) gel layer in situ depositing on it. The SiO(2) interlayer was conceived to play an important role in the resultant sandwich structured SiO(2)/Cyt c/SiO(2)/BDD electrode as a selective "semi-open" medium, which guaranteed the immobilized Cyt c to maintain high stability and perform good electrochemistry and biocatalysis responses. The bioactivity of Cyt c was well protected and the immobilized biomolecule even didn't denature at extremely high or low pH condition. More attractively, Cyt c in the sandwich structured electrode could be further oxidized into highly reactive Cyt c pi-cation by two-step electrochemical oxidation, which could oxidize NO(2)(-) into NO(3)(-) in the solution. A sensitive determination approach of nitrite was accordingly built up based on this biocatalytic oxidative interaction for the first time and a possible mechanism of the interaction was herein proposed.

  10. Positive electrodes of nickel-cadmium batteries

    NASA Technical Reports Server (NTRS)

    Wabner, D. W.; Kandler, L.; Krienke, W.

    1985-01-01

    Ni hydroxide sintered electrodes which are filled electrochemically are superior to chemically treated electrodes. In the electrochemical process, the hydroxide grows on the Ni grains and possesses a well-defined porous structure. Diffusion and conducting mechanisms are therefore facilitated.

  11. Estimation of the Influence of Thin Air Layers on Structures by the Use of Qualitative One-Dimensional Models

    NASA Astrophysics Data System (ADS)

    Chimeno Manguan, M.; Roibas Millan, E.; Simon Hidalgo, F.

    2014-06-01

    Air layers are regions of air between structural elements than can be found in numerous spacecraft structures. The space between folded solar panels and between antennas and a satellite's body are cases of air layers. For some cases, depending on the flexibility of the contiguous structures, the contribution of air layers can modify noticeably the dynamic response of a spacecraft structure. The analysis of these problems in detailed numerical models as Finite and Boundary Element models are characterised by a very small element size because of the requirements imposed by the thickness of the air layers and the fluid-structure interface. Then, a preliminary assessment of the influence of the air layer allows optimizing the development work flow of these elements. This work presents a methodology to preliminarily assess the influence of air layers in the structural response. The methodology is based on the definition of simplified one-dimensional models for the structure and the air gaps. The study of these simple models can be a useful tool to determine the degree of influence of the air layers in the system. Along with the introduction of the methodology a study on several of the model parameters as the number of degrees of freedom for the air layer or the structure is presented. The performance of the methodology is illustrated with results for several cases including actual spacecraft structures.

  12. Structured Electrode Interfaces

    DTIC Science & Technology

    1989-01-01

    Department of Physics AREA A WORK UNIT NUMBERS University of Puerto Rico, P.O. Box 23343 Rio Piedras, PR 00931-3343 II. CONTROLLING OFFICE NAME AND AOORESS...Report) Approved for public release; Distribucion Unlimited 17. DISTRIBUTION STATEMENT (O the abetracl m(eted In Block 20. Ii diflerent floom Report) 18...sites form a regular lattice, and that the area of the unit cell in that lattice is A. From (28), we write - -4 -- - v(1) -kT V p()= Pi(1) VIui(1

  13. Porous electrode preparation method

    DOEpatents

    Arons, R.M.; Dusek, J.T.

    1983-10-18

    A porous sintered plaque is provided with a bimodal porosity that is especially well suited for use as an electrode within a molten carbonate fuel cell. The coarse porosity is sufficient for admitting gases into contact with the reaction surfaces while the fine porosity is wetted with and retains molten electrolyte on the reaction sites. The electrode structure is prepared by providing a very fine powder of such as nickel oxide and blending the powder with a suitable decomposable binder to form a solid mass. The mass is comminuted into agglomerate size particles substantially larger than the fine oxide particles and formed into a cohesive compact for subsequent sintering. Sintering is carried out at sufficient conditions to bind the agglomerates together into a porous structure having both coarse and fine porosity. Where lithiated nickel oxide cathodes are prepared, the sintering conditions can be moderate enough to retain substantial quantities of lithium within the electrode for adequate conductivity. 2 figs.

  14. Liquid-permeable electrode

    DOEpatents

    Folser, George R.

    1980-01-01

    Electrodes for use in an electrolytic cell, which are liquid-permeable and have low electrical resistance and high internal surface area are provided of a rigid, porous, carbonaceous matrix having activated carbon uniformly embedded throughout. The activated carbon may be catalyzed with platinum for improved electron transfer between electrode and electrolyte. Activated carbon is mixed with a powdered thermosetting phenolic resin and compacted to the desired shape in a heated mold to melt the resin and form the green electrode. The compact is then heated to a pyrolyzing temperature to carbonize and volatilize the resin, forming a rigid, porous structure. The permeable structure and high internal surface area are useful in electrolytic cells where it is necessary to continuously remove the products of the electrochemical reaction.

  15. Experimental investigation of cooling of a plate by ionic wind from a corona-forming wire electrode

    NASA Astrophysics Data System (ADS)

    Elagin, I. A.; Yakovlev, V. V.; Ashikhmin, I. A.; Stishkov, Yu. K.

    2016-08-01

    We report on the results of experimental investigations of the kinematic structure of ionic wind from a wire electrode placed near a heated plate, which plays the role of the earthed electrode. Experiments are carried out in a wide range of voltages for different polarities of the wire for several values of the electrode gap. We compare the structures of the flows emerging as a result of natural convection in open air for different positions of the plate and in the presence of a fast ionic wind jet that considerably intensifies heat transfer in the boundary layer at the heated planar electrode. Local temperature distributions over the plate surface are obtained, as well as the integral dependences of the effective heat removal on the electric parameters of the corona discharge. The velocity of air flows with ionic wind reaches 4 m/s, and the heat power removed from the plate for fixed overheating increases ninefold compared to the situation with natural convection.

  16. Stretchable and transparent electrodes using hybrid structures of graphene-metal nanotrough networks with high performances and ultimate uniformity.

    PubMed

    An, Byeong Wan; Hyun, Byung Gwan; Kim, So-Yun; Kim, Minji; Lee, Mi-Sun; Lee, Kyongsoo; Koo, Jae Bon; Chu, Hye Yong; Bae, Byeong-Soo; Park, Jang-Ung

    2014-11-12

    Transparent electrodes that can maintain their electrical and optical properties stably against large mechanical deformations are essential in numerous applications of flexible and wearable electronics. In this paper, we report a comprehensive analysis of the electrical, optical, and mechanical properties of hybrid nanostructures based on graphene and metal nanotrough networks as stretchable and transparent electrodes. Compared to the single material of graphene or the nanotrough, the formation of this hybrid can improve the uniformity of sheet resistance significantly, that is, a very low sheet resistance (1 Ω/sq) with a standard deviation of less than ±0.1 Ω/sq, high transparency (91% in the visible light regime), and superb stretchability (80% in tensile strain). The successful demonstration of skin-attachable, flexible, and transparent arrays of oxide semiconductor transistors fabricated using hybrid electrodes suggests substantial promise for the next generation of electronic devices.

  17. Fabrication of continuous flow microfluidics device with 3D electrode structures for high throughput DEP applications using mechanical machining.

    PubMed

    Zeinali, Soheila; Çetin, Barbaros; Oliaei, Samad Nadimi Bavil; Karpat, Yiğit

    2015-07-01

    Microfluidics is the combination of micro/nano fabrication techniques with fluid flow at microscale to pursue powerful techniques in controlling and manipulating chemical and biological processes. Sorting and separation of bio-particles are highly considered in diagnostics and biological analyses. Dielectrophoresis (DEP) has offered unique advantages for microfluidic devices. In DEP devices, asymmetric pair of planar electrodes could be employed to generate non-uniform electric fields. In DEP applications, facing 3D sidewall electrodes is considered to be one of the key solutions to increase device throughput due to the generated homogeneous electric fields along the height of microchannels. Despite the advantages, fabrication of 3D vertical electrodes requires a considerable challenge. In this study, two alternative fabrication techniques have been proposed for the fabrication of a microfluidic device with 3D sidewall electrodes. In the first method, both the mold and the electrodes are fabricated using high precision machining. In the second method, the mold with tilted sidewalls is fabricated using high precision machining and the electrodes are deposited on the sidewall using sputtering together with a shadow mask fabricated by electric discharge machining. Both fabrication processes are assessed as highly repeatable and robust. Moreover, the two methods are found to be complementary with respect to the channel height. Only the manipulation of particles with negative-DEP is demonstrated in the experiments, and the throughput values up to 105 particles / min is reached in a continuous flow. The experimental results are compared with the simulation results and the limitations on the fabrication techniques are also discussed.

  18. Magnetohydrodynamic electrode

    DOEpatents

    Marchant, David D.; Killpatrick, Don H.

    1978-01-01

    An electrode capable of withstanding high temperatures and suitable for use as a current collector in the channel of a magnetohydrodynamic (MHD) generator consists of a sintered powdered metal base portion, the upper surface of the base being coated with a first layer of nickel aluminide, an intermediate layer of a mixture of nickel aluminide - refractory ceramic on the first layer and a third or outer layer of a refractory ceramic material on the intermediate layer. The sintered powdered metal base resists spalling by the ceramic coatings and permits greater electrode compliance to thermal shock. The density of the powdered metal base can be varied to allow optimization of the thermal conductivity of the electrode and prevent excess heat loss from the channel.

  19. Cermet electrode

    DOEpatents

    Maskalick, Nicholas J.

    1988-08-30

    Disclosed is a cermet electrode consisting of metal particles of nickel, cobalt, iron, or alloys or mixtures thereof immobilized by zirconia stabilized in cubic form which contains discrete deposits of about 0.1 to about 5% by weight of praseodymium, dysprosium, terbium, or a mixture thereof. The solid oxide electrode can be made by covering a substrate with particles of nickel, cobalt, iron, or mixtures thereof, growing a stabilized zirconia solid oxide skeleton around the particles thereby immobilizing them, contacting the skeleton with a compound of praseodymium, dysprosium, terbium, or a mixture thereof, and heating the skeleton to a temperature of at least 500.degree. C. The electrode can also be made by preparing a slurry of nickel, cobalt, iron, or mixture and a compound of praseodymium, dysprosium, terbium, or a mixture thereof, depositing the slurry on a substrate, heating the slurry to dryness, and growing a stabilized zirconia skeleton around the metal particles.

  20. Sandwich-structured nanohybrid paper based on controllable growth of nanostructured MnO2 on ionic liquid functionalized graphene paper as a flexible supercapacitor electrode.

    PubMed

    Sun, Yimin; Fang, Zheng; Wang, Chenxu; Ariyawansha, K R Rakhitha Malinga; Zhou, Aijun; Duan, Hongwei

    2015-05-07

    A sandwich-structured flexible supercapacitor electrode has been developed based on MnO2 nanonest (MNN) modified ionic liquid (IL) functionalized graphene paper (GP), which is fabricated by functionalizing graphene nanosheets with an amine-terminated IL (i.e., 1-(3-aminopropyl)-3-methylimidazolium bromide) to form freestanding IL functionalized GP (IL-GP), and then modifying IL-GP with a unique MNN structure via controllable template-free ultrasonic electrodeposition. The as-obtained MNN modified IL-GP (MNN/IL-GP) inherits the excellent pseudocapacity of the metal oxide, the high conductivity and electric double layer charging/discharging of IL-graphene composites, and therefore shows an enhanced supercapacitor performance. The maximum specific capacitance of 411 F g(-1) can be achieved by chronopotentiometry at a current density of 1 A g(-1). Meanwhile, the MNN/IL-GP electrode exhibits excellent rate capability and cycling stability, its specific capacitance is maintained at 70% as the current densities increase from 1 to 20 A g(-1) and 85% at a current density of 10 A g(-1) after 10 000 cycles. More importantly, the MNN/IL-GP displays distinguished mechanical stability and flexibility for device packaging, although its thickness is merely 8 μm. These features collectively demonstrate the potential of MNN/IL-GP as a high-performance paper electrode for flexible and lightweight and highly efficient electrochemical capacitor applications.

  1. Photoelectrochemical electrodes

    NASA Technical Reports Server (NTRS)

    Williams, R. M.; Rembaum, A. (Inventor)

    1983-01-01

    The surface of a moderate band gap semiconductor such as p-type molybdenum sulfide is modified to contain an adherent film of charge mediating ionene polymer containing an electroactive unit such as bipyridimium. Electron transport between the electrode and the mediator film is favorable and photocorrosion and recombination processes are suppressed. Incorporation of particles of catalyst such as platinum within the film provides a reduction in overvoltage. The polymer film is readily deposited on the electrode surface and can be rendered stable by ionic or addition crosslinking. Catalyst can be predispersed in the polymer film or a salt can be impregnated into the film and reduced therein.

  2. Photodegradation of the electronic structure of PCBM and C60 films in air

    NASA Astrophysics Data System (ADS)

    Anselmo, Ana S.; Dzwilewski, Andrzej; Svensson, Krister; Moons, Ellen

    2016-05-01

    Fullerenes are common electron acceptors in organic solar cells. Here the photostability in air of the electronic structures of spin-coated PCBM ([6,6]-phenyl-C61-butyric acid methyl ester) and evaporated C60 films are studied using ultraviolet photoelectron spectroscopy (UPS) and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. After exposing these materials in air to simulated sunlight, the filled and empty molecular orbitals are strongly altered, indicating that the conjugated π-system of the C60-cage has degraded. Even a few minutes in normal lab light induces changes. These results stress the importance of protecting fullerene-based films from light and air during processing, operation, and storage.

  3. Polyaniline silver nanoparticle coffee waste extracted porous graphene oxide nanocomposite structures as novel electrode material for rechargeable batteries

    NASA Astrophysics Data System (ADS)

    Sundriyal, Poonam; Bhattacharya, Shantanu

    2017-03-01

    The exploration of new and advanced electrode materials are required in electronic and electrical devices for power storage applications. Also, there has been a continuous endeavour to formulate strategies for extraction of high performance electrode materials from naturally obtained waste products. In this work, we have developed an in situ hybrid nanocomposite from coffee waste extracted porous graphene oxide (CEPG), polyaniline (PANI) and silver nanoparticles (Ag) and have found this novel composite to serve as an efficient electrode material for batteries. The successful interaction among the three phases of the nano-composite i.e. CEPG–PANI–Ag have been thoroughly understood through RAMAN, Fourier transform infrared and x-ray diffraction spectroscopy, morphological studies through field emission scanning electron microscope and transmission electron microscope. Thermo-gravimetric analysis of the nano-composite demonstrates higher thermal stability up-to a temperature of 495 °C. Further BET studies through nitrogen adsorption–desorption isotherms confirm the presence of micro/meso and macro-pores in the nanocomposite sample. The cyclic-voltammetry (CV) analysis performed on CEPG–PANI–Ag nanocomposite exhibits a purely faradic behaviour using nickel foam as a current collector thus suggests the prepared nanocomposite as a battery electrode material. The nanocomposite reports a maximum specific capacity of 1428 C g‑1 and excellent cyclic stability up-to 5000 cycles.

  4. AIR RADIOACTIVITY MONITOR

    DOEpatents

    Bradshaw, R.L.; Thomas, J.W.

    1961-04-11

    The monitor is designed to minimize undesirable background buildup. It consists of an elongated column containing peripheral electrodes in a central portion of the column, and conduits directing an axial flow of radioactively contaminated air through the center of the column and pure air through the annular portion of the column about the electrodes. (AEC)

  5. Ceramic component for electrodes

    DOEpatents

    Marchant, David D.

    1979-01-01

    A ceramic component suitable for preparing MHD generator electrodes consists of HfO.sub.2 and sufficient Tb.sub.4 O.sub.7 to stabilize at least 60 volume percent of the HfO.sub.2 into the cubic structure. The ceramic component may also contain a small amount of PrO.sub.2, Yb.sub.2 O.sub.3 or a mixture of both to improve stability and electronic conductivity of the electrode. The component is highly resistant to corrosion by molten potassium seed and molten coal slag in the MHD fluid and exhibits both ionic and electronic conductivity.

  6. Novel Vertical 3D Structure of TaOx-based RRAM with Self-localized Switching Region by Sidewall Electrode Oxidation

    PubMed Central

    Yu, Muxi; Cai, Yimao; Wang, Zongwei; Fang, Yichen; Liu, Yefan; Yu, Zhizhen; Pan, Yue; Zhang, Zhenxing; Tan, Jing; Yang, Xue; Li, Ming; Huang, Ru

    2016-01-01

    A novel vertical 3D RRAM structure with greatly improved reliability behavior is proposed and experimentally demonstrated through basically compatible process featuring self-localized switching region by sidewall electrode oxidation. Compared with the conventional structure, due to the effective confinement of the switching region, the newly-proposed structure shows about two orders higher endurance (>108 without verification operation) and better retention (>180h@150 °C), as well as high uniformity. Corresponding model is put forward, on the base of which thorough theoretical analysis and calculations are conducted as well, demonstrating that, resulting from the physically-isolated switching from neighboring cells, the proposed structure exhibits dramatically improved reliability due to effective suppression of thermal effects and oxygen vacancies diffusion interference, indicating that this novel structure is very promising for future high density 3D RRAM application. PMID:26884054

  7. Potential-induced structural transitions of DL-homocysteine monolayers on Au(1 1 1) electrode surfaces

    NASA Astrophysics Data System (ADS)

    Zhang, Jingdong; Demetriou, Anna; Welinder, Anne Christina; Albrecht, Tim; Nichols, Richard J.; Ulstrup, Jens

    2005-12-01

    Monolayers of homocysteine on Au(1 1 1)-surfaces have been investigated by voltammetry, in situ scanning tunnelling microscopy (STM) and subtractively normalised interfacial Fourier transform spectroscopy (SNIFTIRS). A pair of sharp voltammetric peaks build up in the potential range 0 to -0.1 V (vs. SCE) in phosphate buffer pH 7.7. The peak half-widths are about 25 mV at a scan rate of 10 mV s -1. This is much smaller than for a one-electron Faradaic process (90.6 mV) under similar conditions. The coverage of homocysteine is 6.1 (±0.2) × 10 -10 mol cm -2, or 5.9 × 10 -5 C cm -2, from Au-S reductive desorption at -0.8 V (SCE) in 0.1 M NaOH, while the charge is only about 8 × 10 -6 C cm -2 (pH 7.7) for the 0 to -0.1 V peak. This suggests a capacitive origin. The peak potential and shape depend on pH. At pH 7.7 both cathodic and anodic peak currents reach a maximum, but drop at both higher and lower pH. The midpoint potential shows biphasic behaviour, decreasing linearly with increasing pH until pH 10.4 towards a constant value at higher pH. The cathodic and anodic peak charges decay at pH both higher and lower than 7.7. The homocysteine monolayer was investigated by in situ STM at different potentials at pH 7.7. The molecules pack into highly ordered domains around the peak potential. High-resolution in situ STM reveals a (√3 × 5) R30° lattice with three homocysteine molecules in each unit cell. The adlayer changes into disordered structures on either side of the peak potential. This process is reversible. We propose that the voltammetric peaks are capacitive. The ordered domains are formed only around the potential of zero charge (pzc) and dissipate at potentials on either side of the peak, inducing mirror charge flow in the metallic electrode as the charged -COO - and -NH3+ groups approach the surface. No bands for carboxylate coordinated to the surface were observed in SNIFTIRS implying more subtle orientation changes of the charged groups on transcending

  8. A Novice-Expert Study of Modeling Skills and Knowledge Structures about Air Quality

    ERIC Educational Resources Information Center

    Hsu, Ying-Shao; Lin, Li-Fen; Wu, Hsin-Kai; Lee, Dai-Ying; Hwang, Fu-Kwun

    2012-01-01

    This study compared modeling skills and knowledge structures of four groups as seen in their understanding of air quality. The four groups were: experts (atmospheric scientists), intermediates (upper-level graduate students in a different field), advanced novices (talented 11th and 12th graders), and novices (10th graders). It was found that when…

  9. Numerical study on air-structure coupling dynamic characteristics of the axial fan blade

    NASA Astrophysics Data System (ADS)

    Chen, Q. G.; Xie, B.; Li, F.; Gu, W. G.

    2013-12-01

    In order to understand the dynamic characteristics of the axial-flow fan blade due to the effect of rotating stress and the action of unsteady aerodynamic forces caused by the airflow, a numerical simulation method for air-structure coupling in an axial-flow fan with fixed rear guide blades was performed. The dynamic characteristics of an axial-flow fan rotating blade were studied by using the two-way air-structure coupling method. Based on the standard k-ε turbulence model, and using weak coupling method, the preceding six orders modal parameters of the rotating blade were obtained, and the distributions of stress and strain on the rotating blade were presented. The results show that the modal frequency from the first to the sixth order is 3Hz higher than the modal frequency without considering air-structure coupling interaction; the maximum stress and the maximum strain are all occurred in the vicinity of root area of the blade no matter the air-structure coupling is considered or not, thus, the blade root is the dangerous location subjected to fatigue break; the position of maximum deformation is at the blade tip, so the vibration of the blade tip is significant. This study can provide theoretical references for the further study on the strength analysis and mechanical optimal design.

  10. Effect of scintillometer height on structure parameter of the refractive index of air measurements

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Scintillometers measure amount of scintillations by emitting a beam of light over a horizontal path and expresses as the atmospheric turbulence structure parameter as the refractive index of air (Cn**2). Cn**2 represents the turbulent strength of the atmosphere and describes the ability of the atmos...

  11. Understanding the structure of hydrophobic surfactants at the air/water interface from molecular level.

    PubMed

    Zhang, Li; Liu, Zhipei; Ren, Tao; Wu, Pan; Shen, Jia-Wei; Zhang, Wei; Wang, Xinping

    2014-11-25

    Understanding the behavior of fluorocarbon surfactants at the air/water interface is crucial for many applications, such as lubricants, paints, cosmetics, and fire-fighting foams. In this study, molecular dynamics (MD) simulations were employed to investigate the microscopic properties of non-ionic fluorocarbon surfactants at the air/water interface. Several properties, including the distribution of head groups, the distribution probability of the tilt angle between hydrophobic tails with respect to the xy plane, and the order parameter of surfactants, were computed to probe the structure of hydrophobic surfactants at the air/water interface. The effects of the monomer structure on interfacial phenomena of non-ionic surfactants were investigated as well. It is observed that the structure of fluorocarbon surfactants at the air/water interface is more ordered than that of hydrocarbons, which is dominated by the van der Waals interaction between surfactants and water molecules. However, replacing one or two CF2 with one or two CH2 group does not significantly influence the interfacial structure, suggesting that hydrocarbons may be promising alternatives to perfluorinated surfactants.

  12. The effect of structures on indoor humidity--possibility to improve comfort and perceived air quality.

    PubMed

    Simonson, C J; Salonvaara, M; Ojanen, T

    2002-12-01

    The research presented in this paper shows that moisture transfer between indoor air and hygroscopic building structures can generally improve indoor humidity conditions. This is important because the literature shows that indoor humidity has a significant effect on occupant comfort, perceived air quality (PAQ), occupant health, building durability, material emissions, and energy consumption. Therefore, it appears possible to improve the quality of life of occupants when appropriately applying hygroscopic wood-based materials. The paper concentrates on the numerical investigation of a bedroom in a wooden building located in four European countries (Finland, Belgium, Germany, and Italy). The results show that moisture transfer between indoor air and the hygroscopic structure significantly reduces the peak indoor humidity. Based on correlations from the literature, which quantify the effect of temperature and humidity on comfort and PAQ for sedentary adults, hygroscopic structures can improve indoor comfort and air quality. In all the investigated climates, it is possible to improve the indoor conditions such that, as many as 10 more people of 100 are satisfied with the thermal comfort conditions (warm respiratory comfort) at the end of occupation. Similarly, the percent dissatisfied with PAQ can be 25% lower in the morning when permeable and hygroscopic structures are applied.

  13. Origin and Control of the Flow Structure on Unmanned Combat Air Vehicle

    DTIC Science & Technology

    2007-12-01

    Prescrtbed by ANSI Ski Z3S.18 AFOSR Final Repot 013108 ORIGIN AND CONTROL OF THE FLOW STRUCTURE ON UNMANNED COMBAT AIR VEHICLES AFOSR GRANT #FA9550-05...1991) described low-dimensional models for flows past a grooved channel and circular cylinders. By employing a Galerkin method, a governing partial

  14. Microvoltammetric Electrodes.

    DTIC Science & Technology

    1985-09-25

    Microvoltammetric Electrodes, J. 0. Howell, R. M. Wightman, Anal. Chem., 56, 524-529 (1984). 2. Flow Rate Independent Amperometric Cell , W. L. Caudill...Electroanal. Chem., 182, 113-122 (1985). C. List of all publications 1. Flow Rate Independent Amperometric Cell , W. L. Caudill, J. 0. Howell, R. M

  15. Foam and cluster structure formation by latex particles at the air/water interface

    NASA Astrophysics Data System (ADS)

    Ruiz-Garcia, Jaime; Gámez-Corrales, Rogelio; Ivlev, Boris I.

    1997-02-01

    We report the formation of two-dimensional foam and cluster structures by spherical polystyrene particles trapped at the air/water interface. The colloidal foam is a transient structure that evolves to the formation of clusters, but clusters can also be formed after deposition of the sample. We also observed the formation of small aggregates, whose formation along with the cluster stabilization can be explained in terms of a balance between electrostatic repulsive and van der Waals attractive interactions.

  16. Fuel cell electrode

    SciTech Connect

    Struthers, R. C.

    1985-03-05

    A flat, laminated fuel cell gas electrode arranged between and separating gas and liquid mediums in a fuel cell. The electrode includes a flat, perforated sheet metal support and electric conductor part with a rear surface disposed toward the gas medium, a flat, hydrophobic gas permeable membrane with a rear surface in contact with a front surface of said part, a flat liquid and gas permeable metallic current collector with a rear surface spaced from a front surface of said membrane and with a front surface disposed toward the liquid medium, a catalytic barrier structure of bonded together particulate catalytic material and metal conductor filaments by and in electric conducting contact with the collector and having a rear surface in contact with the front surface of the membrane and a plurality of spaced apart electric conducting fasteners engaged with and between said part and collector securing the parts of the electrode in assembled relationship and electrically connecting the current collector with said part.

  17. Influence of fundamental material properties and air void structure on moisture damage of asphalt mixes

    NASA Astrophysics Data System (ADS)

    Arambula Mercado, Edith

    2007-12-01

    Moisture damage in asphalt mixes refers to the loss of serviceability due to the presence of moisture. The extent of moisture damage, also called moisture susceptibility, depends on internal and external factors. The internal factors relate to the properties of the materials and the microstructure distribution, while the external factors include the environmental conditions, production and construction practices, pavement design, and traffic level. The majority of the research on moisture damage is based on the hypothesis that infiltration of surface water is the main source of moisture. Of the two other principal mechanisms of water transport, permeation of water vapor and capillary rise of subsurface water, the latter has been least explored. A laboratory test and analysis methods based on X-ray computed tomography (CT) were established to assess the capillary rise of water. The amount and size of air voids filled with water were used in the capillary rise equation to estimate the distribution of the contact angles between the water and the mastic. The results were able to show the influence of air void size on capillary rise and contact angles. The relationship between air void structure and moisture susceptibility was evaluated using a fundamental fracture model based on dissipated energy of viscoelastic materials. Detailed description is provided in this dissertation on the deduction of the model equation, the selection of the model parameters, and the required testing protocols. The model parameters were obtained using mechanical tests and surface energy measurements. The microstructure of asphalt mixes prepared in the laboratory having different air void structures was captured using X-ray CT, and image analysis techniques were used to quantify the air void structure and air void connectivity. The air void structure was found to influence the mix resistance to moisture damage. To validate the fracture model, asphalt mixes with known field performance were

  18. Effect of gravity on the stability and structure of lean hydrogen-air flames

    NASA Technical Reports Server (NTRS)

    Patnaik, G.; Kailasanath, K.

    1991-01-01

    Detailed, time-dependent, 2D numerical simulations with full hydrogen-oxygen chemistry are used to investigate the effects of gravity on the stability and structure of laminar flames in lean, premixed hydrogen-air mixtures. The calculations show that the effects of gravity becomes more important as the lean flammability limit is approached. In a 12 percent hydrogen-air mixture, gravity plays only a secondary role in determining the multidimensional structure of the flame with the stability and structure of the flame controlled primarily by the thermo-diffusive instability mechanism. However, in leaner hydrogen-air mixtures gravity becomes more important. Upward-propagating flames are highly curved and evolve into a bubble rising upwards in the tube. Downward-propagating flames are flat or even oscillate between structures with concave and convex curvatures. The zero-gravity flame shows only cellular structures. Cellular structures which are present in zero gravity can be suppressed by the effect of buoyancy for mixtures leaner than 11 percent hydrogen. These observations are explained on the basis of an interaction between the processes leading to buoyancy-induced Rayleigh-Taylor instability and the thermo-diffusive instability.

  19. Engineering the Electrode-Electrolyte Interface: From Electrode Architecture to Zinc Redox in Ionic Liquid Electrolytes

    NASA Astrophysics Data System (ADS)

    Engstrom, Erika

    2011-12-01

    The electrode-electrolyte interface in electrochemical environments involves the understanding of complex processes relevant for all electrochemical applications. Some of these processes include electronic structure, charge storage, charge transfer, solvent dynamics and structure and surface adsorption. In order to engineer electrochemical systems, no matter the function, requires fundamental intuition of all the processes at the interface. The following work presents different systems in which the electrode-electrolyte interface is highly important. The first is a charge storage electrode utilizing percolation theory to develop an electrode architecture producing high capacities. This is followed by Zn deposition in an ionic liquid in which the deposition morphology is highly dependant on the charge transfer and surface adsorption at the interface. Electrode Architecture: A three-dimensional manganese oxide supercapacitor electrode architecture is synthesized by leveraging percolation theory to develop a hierarchically designed tri-continuous percolated network. The three percolated phases include a faradaically-active material, electrically conductive material and pore-former templated void space. The micropores create pathways for ionic conductivity, while the nanoscale electrically conducting phase provides both bulk conductivity and local electron transfer with the electrochemically active phase. Zn Electrodeposition: Zn redox in air and water stable N-ethyl-N-methylmorpholinium bis(trifluoromethanesulfonyl)imide, [C2nmm][NTf2] is presented. Under various conditions, characterization of overpotential, kinetics and diffusion of Zn species and morphological evolution as a function of overpotential and Zn concentration are analyzed. The surface stress evolution during Zn deposition is examined where grain size and texturing play significant rolls in compressive stress generation. Morphological repeatability in the ILs led to a novel study of purity in ionic

  20. Ultrasensitive detection of lead ion sensor based on gold nanodendrites modified electrode and electrochemiluminescent quenching of quantum dots by electrocatalytic silver/zinc oxide coupled structures.

    PubMed

    Li, Meng; Kong, Qingkun; Bian, Zhaoquan; Ma, Chao; Ge, Shenguang; Zhang, Yan; Yu, Jinghua; Yan, Mei

    2015-03-15

    A signal-off electrochemiluminescence (ECL) DNA sensor based on gold nanodendrites (Au NDs) modified indium tin oxide (ITO) electrode for the detection of lead ion (Pb(2+)) was developed. Well-defined Au NDs were prepared on ITO electrode using low-potential synthesis, assisted by ethylenediamine. Based on Pb(2+)-specific deoxyribozyme, the silver/zinc oxide (Ag/ZnO) with coupled structure, prepared by one-pot method, was close to the surface of the electrode to catalyze the reduction of part of H2O2, the coreactant for cathodic ECL emission, leading to a decrease of ECL intensity. In addition, taking advantage of the larger surface area to capture a large amount of capture probe as well as excellent conductivity of Au NDs, the sensor could detect Pb(2+) quantitatively in a wider range, and performed excellent selectivity. Furthermore, such simple and sensitive DNA sensor was successfully applied for the detection of Pb(2+) in lake water and human serum samples, respectively.

  1. The secondary alkaline zinc electrode

    NASA Astrophysics Data System (ADS)

    McLarnon, Frank R.; Cairns, Elton J.

    1991-02-01

    The worldwide studies conducted between 1975 and 1990 with the aim of improving cell lifetimes of secondary alkaline zinc electrodes are overviewed. Attention is given the design features and characteristics of various secondary alkaline zinc cells, including four types of zinc/nickel oxide cell designs (vented static-electrolyte, sealed static-electrolyte, vibrating-electrode, and flowing-electrolyte); two types of zinc/air cells (mechanically rechargeable consolidated-electrode and mechanically rechargeable particulate-electrode); zinc/silver oxide battery; zinc/manganese dioxide cell; and zinc/ferric cyanide battery. Particular consideration is given to recent research in the fields of cell thermodynamics, zinc electrodeposition, zinc electrodissolution, zinc corrosion, electrolyte properties, mathematical and phenomenological models, osmotic pumping, nonuniform current distribution, and cell cycle-life perforamnce.

  2. Radiotracer Evaluation of the Contribution of Degradation Products of Phenolic Resins to the Poisoning of Electrodes in the 190 C Hydrogen/Air Fuel Cell.

    DTIC Science & Technology

    1980-12-01

    R.F. Pascoe , H.R. Kunz, "Surface Area Loss of Platinum Supported on Carbon in Phosphoric Acid Electrolyte", J. Electrochem. Soc. 127, 1219 (1980). 4...1a. SUPPLEMENTARY NOTES IS. KEY WORDS (Contin he a reverse side It noceasm, mid Identify by block number) Fuel cells, phosphoric acid , bipolar...plates, phenolic resins, composite graphite, Carbon-14, radiotracer, electro-catalyst, electrode poisoning, platinum on carbon catalyst, acid -resistant

  3. Effects of air pollution on thermal structure and dispersion in an urban planetary boundary layer

    NASA Technical Reports Server (NTRS)

    Viskanta, R.; Johnson, R. O.; Bergstrom, R. W.

    1977-01-01

    The short-term effects of urbanization and air pollution on the transport processes in the urban planetary boundary layer (PBL) are studied. The investigation makes use of an unsteady two-dimensional transport model which has been developed by Viskanta et al., (1976). The model predicts pollutant concentrations and temperature in the PBL. The potential effects of urbanization and air pollution on the thermal structure in the urban PBL are considered, taking into account the results of numerical simulations modeling the St. Louis, Missouri metropolitan area.

  4. Electric field and dewetting induced hierarchical structure formation in polymer/polymer/air trilayers.

    PubMed

    Leach, K Amanda; Gupta, Suresh; Dickey, Michael D; Willson, C Grant; Russell, Thomas P

    2005-12-01

    Electrohydrodynamics were studied in a trilayer thin film system consisting of two different polymeric layers and air. A polymer with a higher dielectric constant, poly(methyl methacrylate), was sandwiched between air and a lower dielectric constant polymer, polystyrene. An electric field was applied normal to the interfaces. Along with electrostatic forces, dewetting forces were significant at two of the interfaces, namely, the polystyrene/silicon wafer and the polystyrene/poly(methyl methacrylate) interfaces. These two combined forces produce novel closed-cell structures that are difficult to produce by other existing techniques.

  5. CONDENSED MATTER: ELECTRONIC STRUCTURE, ELECTRICAL, MAGNETIC, AND OPTICAL PROPERTIES: Kondo effect in a deformed molecule coupled asymmetrically to ferromagnetic electrodes

    NASA Astrophysics Data System (ADS)

    Wang, Rui-Qiang; Jiang, Kai-Ming

    2009-12-01

    The nonequilibrium Kondo effect is studied in a molecule quantum dot coupled asymmetrically to two ferromagnetic electrodes by employing the nonequilibrium Green function technique. The current-induced deformation of the molecule is taken into account, modeled as interactions with a phonon system, and phonon-assisted Kondo satellites arise on both sides of the usual main Kondo peak. In the antiparallel electrode configuration, the Kondo satellites can be split only for the asymmetric dot-lead couplings, distinguished from the parallel configuration where splitting also exists, even though it is for symmetric case. We also analyze how to compensate the splitting and restore the suppressed zero-bias Kondo resonance. It is shown that one can change the TMR ratio significantly from a negative dip to a positive peak only by slightly modulating a local external magnetic field, whose value is greatly dependent on the electron-phonon coupling strength.

  6. Self-assembly of virus-structured high surface area nanomaterials and their application as battery electrodes.

    PubMed

    Royston, Elizabeth; Ghosh, Ayan; Kofinas, Peter; Harris, Michael T; Culver, James N

    2008-02-05

    High area nickel and cobalt surfaces were assembled using modified Tobacco mosaic virus (TMV) templates. Rod-shaped TMV templates (300 x 18 nm) engineered to encode unique cysteine residues were self-assembled onto gold patterned surfaces in a vertically oriented fashion, producing a >10-fold increase in surface area. Electroless deposition of ionic metals onto surface-assembled virus templates produced uniform metal coatings up to 40 nm in thickness. Within a nickel-zinc battery system, the incorporation of virus-assembled electrode surfaces more than doubled the total electrode capacity. When combined, these findings demonstrate that surface-assembled virus templates provide a robust platform for the fabrication of oriented high surface area materials.

  7. Method of forming a leak proof plasma sprayed interconnection layer on an electrode of an electrochemical cell

    DOEpatents

    Kuo, Lewis J. H.; Vora, Shailesh D.

    1995-01-01

    A dense, substantially gas-tight, electrically conductive interconnection layer is formed on an electrode structure of an electrochemical cell by: (A) providing an electrode structure; (B) forming on a selected portion of the electrode surface, an interconnection layer having the general formula La.sub.1-x M.sub.x Cr.sub.1-y N.sub.y O.sub.3, where M is a dopant selected from the group of Ca, Sr, Ba, and mixtures thereof, and where N is a dopant selected from the group of Mg, Co, Ni, Al, and mixtures thereof, and where x and y are each independently about 0.075-0.25, by thermally spraying, preferably plasma arc spraying, a flux added interconnection spray powder, preferably agglomerated, the flux added powder comprising flux particles, preferably including dopant, preferably (CaO).sub.12. (Al.sub.2 O.sub.3).sub.7 flux particles including Ca and Al dopant, and LaCrO.sub.3 interconnection particles, preferably undoped LaCrO.sub.3, to form a dense and substantially gas-tight interconnection material bonded to the electrode structure by a single plasma spraying step; and, (C) heat treating the interconnection layer at from about 1200.degree. to 1350.degree. C. to further densify and heal the micro-cracks and macro-cracks of the thermally sprayed interconnection layer. The result is a substantially gas-tight, highly doped, electrically conductive interconnection material bonded to the electrode structure. The electrode structure can be an air electrode, and a solid electrolyte layer can be applied to the unselected portion of the air electrode, and further a fuel electrode can be applied to the solid electrolyte, to form an electrochemical cell for generation of electrical power.

  8. Method of forming a leak proof plasma sprayed interconnection layer on an electrode of an electrochemical cell

    DOEpatents

    Kuo, L.J.H.; Vora, S.D.

    1995-02-21

    A dense, substantially gas-tight, electrically conductive interconnection layer is formed on an electrode structure of an electrochemical cell by: (A) providing an electrode structure; (B) forming on a selected portion of the electrode surface, an interconnection layer having the general formula La{sub 1{minus}x}M{sub x}Cr{sub 1{minus}y}N{sub y}O{sub 3}, where M is a dopant selected from the group of Ca, Sr, Ba, and mixtures thereof, and where N is a dopant selected from the group of Mg, Co, Ni, Al, and mixtures thereof, and where x and y are each independently about 0.075--0.25, by thermally spraying, preferably plasma arc spraying, a flux added interconnection spray powder, preferably agglomerated, the flux added powder comprising flux particles, preferably including dopant, preferably (CaO){sub 12}(Al{sub 2}O{sub 3}){sub 7} flux particles including Ca and Al dopant, and LaCrO{sub 3} interconnection particles, preferably undoped LaCrO{sub 3}, to form a dense and substantially gas-tight interconnection material bonded to the electrode structure by a single plasma spraying step; and (C) heat treating the interconnection layer at from about 1,200 to 1,350 C to further densify and heal the micro-cracks and macro-cracks of the thermally sprayed interconnection layer. The result is a substantially gas-tight, highly doped, electrically conductive interconnection material bonded to the electrode structure. The electrode structure can be an air electrode, and a solid electrolyte layer can be applied to the unselected portion of the air electrode, and further a fuel electrode can be applied to the solid electrolyte, to form an electrochemical cell for generation of electrical power. 4 figs.

  9. STRUCTURE-ACTIVITY APPROACHES AND DATA EXPLORATION TOOLS FOR PRIORITIZING AND ASSESSING THE TOXICITY OF HAZARDOUS AIR POLLUTANTS

    EPA Science Inventory


    STRUCTURE-ACTIVITY APPROACHES AND DATA EXPLORATION TOOLS FOR PRIORITIZING AND ASSESSING THE TOXICITY OF HAZARDOUS AIR POLLUTANTS

    Hazardous Air Pollutants (HAPs) refers to a set of structurally diverse environmental chemicals, many with limited toxicity data, that have...

  10. Effect of charging methods on battery electrodes

    NASA Astrophysics Data System (ADS)

    McBreen, J.

    The effect of modified charging methods on the structure and behavior of several battery electrodes are reviewed. These include the alkaline cadmium, zinc, silver oxide and nickel oxide electrodes. Also included are recent results obtained for pasted zinc electrodes and in acidic zinc chloride electrolytes. Modified charging methods can greatly affect electrodes particularly when the charging reaction involving the nucleation, and growth of a new phase. Many of the observed morphological effects are described with regard to nucleation and orientation effects.

  11. Electrically conductive connection for an electrode

    DOEpatents

    Hornack, Thomas R.; Chilko, Robert J.

    1986-01-01

    An electrically conductive connection for an electrode assembly of an electrolyte cell in which aluminum is produced by electrolysis in a molten salt is described. The electrode assembly comprises an electrode flask and a conductor rod. The flask has a collar above an area of minimum flask diameter. The electrically conductive connection comprises the electrode flask, the conductor rod and a structure bearing against the collar and the conductor rod for pulling the conductor rod into compressive and electrical contact with the flask.

  12. Structural and electrical characterization of organic monolayers by Atomic Force Microscopy and through the nano-fabrication of a coplanar electrode-dielectric platform

    NASA Astrophysics Data System (ADS)

    Martin, Florent

    Correlating structural and electrical properties of organic thin films is a key requirement to understand charge transport in these materials. The electrical conductivity of organic films should be strongly dependent on how the molecules arrange to form films and crystals. Here we report on the structural and electrical characterization of organic monolayers by Atomic Force Microscopy and through the nano-fabrication of a coplanar electrode-dielectric platform. Organic monolayers were prepared using the solution-based Langmuir-Blodgett technique and transferred to a variety of substrates. Atomic Force Microscopy (AFM) was used to analyze the morphology and the microstructure of ultra-thin films at high resolution while electron diffraction measurements were instrumental in determining the lattice and orientation of crystalline domains within monolayers. A novel Conducting probe AFM method based on the presence of an insulating oxide layer between an organic film and a conductive silicon substrate made it possible to probe the in-plane electrical conductivity in the film. With this technique, we were able to investigate the correlation between conduction properties of oligothiophene monolayers and structural factors such as their molecular order and their lattice orientation. In order to make electrical contacts with monolayer films and study them in a Field Effect Transistor (FET) configuration, we developed coplanar electrode-dielectric substrates with roughness and surface topography in the sub-nanometer range. We present the first results on the electrical characterization of monolayers with this device which demonstrate that the coplanar geometry leads to a contact resistance by orders of magnitude lower than that found in conventional 20nm thick electrodes.

  13. Method Of Bonding A Metal Connection To An Electrode Including A Core Having A Fiber Or Foam Type Structure For An Electrochemical Cell, An

    DOEpatents

    Loustau, Marie-Therese; Verhoog, Roelof; Precigout, Claude

    1996-09-24

    A method of bonding a metal connection to an electrode including a core having a fiber or foam-type structure for an electrochemical cell, in which method at least one metal strip is pressed against one edge of the core and is welded thereto under compression, wherein, at least in line with the region in which said strip is welded to the core, which is referred to as the "main core", a retaining core of a type analogous to that of the main core is disposed prior to the welding.

  14. Accurate Assessment of the Oxygen Reduction Electrocatalytic Activity of Mn/Polypyrrole Nanocomposites Based on Rotating Disk Electrode Measurements, Complemented with Multitechnique Structural Characterizations.

    PubMed

    Bocchetta, Patrizia; Sánchez, Carolina Ramírez; Taurino, Antonietta; Bozzini, Benedetto

    2016-01-01

    This paper reports on the quantitative assessment of the oxygen reduction reaction (ORR) electrocatalytic activity of electrodeposited Mn/polypyrrole (PPy) nanocomposites for alkaline aqueous solutions, based on the Rotating Disk Electrode (RDE) method and accompanied by structural characterizations relevant to the establishment of structure-function relationships. The characterization of Mn/PPy films is addressed to the following: (i) morphology, as assessed by Field-Emission Scanning Electron Microscopy (FE-SEM) and Atomic Force Microscope (AFM); (ii) local electrical conductivity, as measured by Scanning Probe Microscopy (SPM); and (iii) molecular structure, accessed by Raman Spectroscopy; these data provide the background against which the electrocatalytic activity can be rationalised. For comparison, the properties of Mn/PPy are gauged against those of graphite, PPy, and polycrystalline-Pt (poly-Pt). Due to the literature lack of accepted protocols for precise catalytic activity measurement at poly-Pt electrode in alkaline solution using the RDE methodology, we have also worked on the obtainment of an intralaboratory benchmark by evidencing some of the time-consuming parameters which drastically affect the reliability and repeatability of the measurement.

  15. Accurate Assessment of the Oxygen Reduction Electrocatalytic Activity of Mn/Polypyrrole Nanocomposites Based on Rotating Disk Electrode Measurements, Complemented with Multitechnique Structural Characterizations

    PubMed Central

    Sánchez, Carolina Ramírez; Taurino, Antonietta; Bozzini, Benedetto

    2016-01-01

    This paper reports on the quantitative assessment of the oxygen reduction reaction (ORR) electrocatalytic activity of electrodeposited Mn/polypyrrole (PPy) nanocomposites for alkaline aqueous solutions, based on the Rotating Disk Electrode (RDE) method and accompanied by structural characterizations relevant to the establishment of structure-function relationships. The characterization of Mn/PPy films is addressed to the following: (i) morphology, as assessed by Field-Emission Scanning Electron Microscopy (FE-SEM) and Atomic Force Microscope (AFM); (ii) local electrical conductivity, as measured by Scanning Probe Microscopy (SPM); and (iii) molecular structure, accessed by Raman Spectroscopy; these data provide the background against which the electrocatalytic activity can be rationalised. For comparison, the properties of Mn/PPy are gauged against those of graphite, PPy, and polycrystalline-Pt (poly-Pt). Due to the literature lack of accepted protocols for precise catalytic activity measurement at poly-Pt electrode in alkaline solution using the RDE methodology, we have also worked on the obtainment of an intralaboratory benchmark by evidencing some of the time-consuming parameters which drastically affect the reliability and repeatability of the measurement. PMID:28042491

  16. Capacitance enhancement via electrode patterning

    NASA Astrophysics Data System (ADS)

    Ho, Tuan A.; Striolo, Alberto

    2013-11-01

    The necessity of increasing the energy density in electric double layer capacitors to meet current demand is fueling fundamental and applied research alike. We report here molecular dynamics simulation results for aqueous electrolytes near model electrodes. Particular focus is on the effect of electrode patterning on the structure of interfacial electrolytes, and on the potential drop between the solid electrodes and the bulk electrolytes. The latter is estimated by numerically integrating the Poisson equation using the charge densities due to water and ions accumulated near the interface as input. We considered uniform and patterned electrodes, both positively and negatively charged. The uniformly charged electrodes are modeled as graphite. The patterned ones are obtained by removing carbon atoms from the top-most graphene layer, yielding nanoscopic squares and stripes patterns. For simplicity, the patterned electrodes are effectively simulated as insulators (the charge remains localized on the top-most layer of carbon atoms). Our simulations show that the patterns alter the structure of water and the accumulation of ions at the liquid-solid interfaces. Using aqueous NaCl solutions, we found that while the capacitance calculated for three positively charged electrodes did not change much, that calculated for the negatively charged electrodes significantly increased upon patterning. We find that both water structure and orientation, as well as ion accumulation affect the capacitance. As electrode patterning affects differently water structure and ion accumulation, it might be possible to observe ion-specific effects. These results could be useful for advancing our understanding of electric double layer capacitors, capacitive desalination processes, as well as of fundamental interfacial electrolytes properties.

  17. Capacitance enhancement via electrode patterning

    SciTech Connect

    Ho, Tuan A.; Striolo, Alberto

    2013-11-28

    The necessity of increasing the energy density in electric double layer capacitors to meet current demand is fueling fundamental and applied research alike. We report here molecular dynamics simulation results for aqueous electrolytes near model electrodes. Particular focus is on the effect of electrode patterning on the structure of interfacial electrolytes, and on the potential drop between the solid electrodes and the bulk electrolytes. The latter is estimated by numerically integrating the Poisson equation using the charge densities due to water and ions accumulated near the interface as input. We considered uniform and patterned electrodes, both positively and negatively charged. The uniformly charged electrodes are modeled as graphite. The patterned ones are obtained by removing carbon atoms from the top-most graphene layer, yielding nanoscopic squares and stripes patterns. For simplicity, the patterned electrodes are effectively simulated as insulators (the charge remains localized on the top-most layer of carbon atoms). Our simulations show that the patterns alter the structure of water and the accumulation of ions at the liquid-solid interfaces. Using aqueous NaCl solutions, we found that while the capacitance calculated for three positively charged electrodes did not change much, that calculated for the negatively charged electrodes significantly increased upon patterning. We find that both water structure and orientation, as well as ion accumulation affect the capacitance. As electrode patterning affects differently water structure and ion accumulation, it might be possible to observe ion-specific effects. These results could be useful for advancing our understanding of electric double layer capacitors, capacitive desalination processes, as well as of fundamental interfacial electrolytes properties.

  18. FUEL CELL ELECTRODES FOR ACID MEDIA

    DTIC Science & Technology

    fuel cell electrodes for acid media. Activated carbon electrodes were prepared, wetproofed with paraffin or Teflon, and catalyzed with platinum. The wetproofing agent was applied by immersion or electrodeposition and the catalyst applied by chemical decomposition of H2P+Cl6 solutions. Half cell studies with hydrogen anodes and oxygen (air) cathodes showed that electrochemical performance is essentially the same for paraffin and Teflontreated electrodes; however, the life of the Teflon-treated electrodes under equal conditions of load is greater than that for

  19. High-capacity electrode materials for rechargeable lithium batteries: Li3NbO4-based system with cation-disordered rocksalt structure

    PubMed Central

    Yabuuchi, Naoaki; Takeuchi, Mitsue; Nakayama, Masanobu; Shiiba, Hiromasa; Ogawa, Masahiro; Nakayama, Keisuke; Ohta, Toshiaki; Endo, Daisuke; Ozaki, Tetsuya; Inamasu, Tokuo; Sato, Kei; Komaba, Shinichi

    2015-01-01

    Rechargeable lithium batteries have rapidly risen to prominence as fundamental devices for green and sustainable energy development. Lithium batteries are now used as power sources for electric vehicles. However, materials innovations are still needed to satisfy the growing demand for increasing energy density of lithium batteries. In the past decade, lithium-excess compounds, Li2MeO3 (Me = Mn4+, Ru4+, etc.), have been extensively studied as high-capacity positive electrode materials. Although the origin as the high reversible capacity has been a debatable subject for a long time, recently it has been confirmed that charge compensation is partly achieved by solid-state redox of nonmetal anions (i.e., oxide ions), coupled with solid-state redox of transition metals, which is the basic theory used for classic lithium insertion materials, such as LiMeO2 (Me = Co3+, Ni3+, etc.). Herein, as a compound with further excess lithium contents, a cation-ordered rocksalt phase with lithium and pentavalent niobium ions, Li3NbO4, is first examined as the host structure of a new series of high-capacity positive electrode materials for rechargeable lithium batteries. Approximately 300 mAh⋅g−1 of high-reversible capacity at 50 °C is experimentally observed, which partly originates from charge compensation by solid-state redox of oxide ions. It is proposed that such a charge compensation process by oxide ions is effectively stabilized by the presence of electrochemically inactive niobium ions. These results will contribute to the development of a new class of high-capacity electrode materials, potentially with further lithium enrichment (and fewer transition metals) in the close-packed framework structure with oxide ions. PMID:26056288

  20. High-capacity electrode materials for rechargeable lithium batteries: Li3NbO4-based system with cation-disordered rocksalt structure.

    PubMed

    Yabuuchi, Naoaki; Takeuchi, Mitsue; Nakayama, Masanobu; Shiiba, Hiromasa; Ogawa, Masahiro; Nakayama, Keisuke; Ohta, Toshiaki; Endo, Daisuke; Ozaki, Tetsuya; Inamasu, Tokuo; Sato, Kei; Komaba, Shinichi

    2015-06-23

    Rechargeable lithium batteries have rapidly risen to prominence as fundamental devices for green and sustainable energy development. Lithium batteries are now used as power sources for electric vehicles. However, materials innovations are still needed to satisfy the growing demand for increasing energy density of lithium batteries. In the past decade, lithium-excess compounds, Li2MeO3 (Me = Mn(4+), Ru(4+), etc.), have been extensively studied as high-capacity positive electrode materials. Although the origin as the high reversible capacity has been a debatable subject for a long time, recently it has been confirmed that charge compensation is partly achieved by solid-state redox of nonmetal anions (i.e., oxide ions), coupled with solid-state redox of transition metals, which is the basic theory used for classic lithium insertion materials, such as LiMeO2 (Me = Co(3+), Ni(3+), etc.). Herein, as a compound with further excess lithium contents, a cation-ordered rocksalt phase with lithium and pentavalent niobium ions, Li3NbO4, is first examined as the host structure of a new series of high-capacity positive electrode materials for rechargeable lithium batteries. Approximately 300 mAh ⋅ g(-1) of high-reversible capacity at 50 °C is experimentally observed, which partly originates from charge compensation by solid-state redox of oxide ions. It is proposed that such a charge compensation process by oxide ions is effectively stabilized by the presence of electrochemically inactive niobium ions. These results will contribute to the development of a new class of high-capacity electrode materials, potentially with further lithium enrichment (and fewer transition metals) in the close-packed framework structure with oxide ions.

  1. Hierarchical self-assembled structures based on nitrogen-doped carbon nanotubes as advanced negative electrodes for Li-ion batteries and 3D microbatteries

    NASA Astrophysics Data System (ADS)

    Sharifi, Tiva; Valvo, Mario; Gracia-Espino, Eduardo; Sandström, Robin; Edström, Kristina; Wågberg, Thomas

    2015-04-01

    Hierarchical structures based on carbon paper and multi-walled nitrogen-doped carbon nanotubes were fabricated and subsequently decorated with hematite nanorods to obtain advanced 3D architectures for Li-ion battery negative electrodes. The carbon paper provides a versatile metal-free 3D current collector ensuring a good electrical contact of the active materials to its carbon fiber network. Firstly, the nitrogen-doped carbon nanotubes onto the carbon paper were studied and a high footprint area capacity of 2.1 mAh cm-2 at 0.1 mA cm-2 was obtained. The Li can be stored in the inter-wall regions of the nanotubes, mediated by the defects formed on their walls by the nitrogen atoms. Secondly, the incorporation of hematite nanorods raised the footprint area capacity to 2.25 mAh cm-2 at 0.1 mA cm-2. However, the repeated conversion/de-conversion of Fe2O3 limited both coulombic and energy efficiencies for these electrodes, which did not perform as well as those including only the N-doped carbon nanotubes at higher current densities. Thirdly, long-cycling tests showed the robust Li insertion mechanism in these N-doped carbonaceous structures, which yielded an unmatched footprint area capacity enhancement up to 1.95 mAh cm-2 after 60 cycles at 0.3 mA cm-2 and an overall capacity of 204 mAh g-1 referred to the mass of the entire electrode.

  2. Electrode assemblies, plasma apparatuses and systems including electrode assemblies, and methods for generating plasma

    DOEpatents

    Kong, Peter C; Grandy, Jon D; Detering, Brent A; Zuck, Larry D

    2013-09-17

    Electrode assemblies for plasma reactors include a structure or device for constraining an arc endpoint to a selected area or region on an electrode. In some embodiments, the structure or device may comprise one or more insulating members covering a portion of an electrode. In additional embodiments, the structure or device may provide a magnetic field configured to control a location of an arc endpoint on the electrode. Plasma generating modules, apparatus, and systems include such electrode assemblies. Methods for generating a plasma include covering at least a portion of a surface of an electrode with an electrically insulating member to constrain a location of an arc endpoint on the electrode. Additional methods for generating a plasma include generating a magnetic field to constrain a location of an arc endpoint on an electrode.

  3. Design and Simulation of a MEMS Structure for Electrophoretic and Dielectrophoretic Separation of Particles by Contactless Electrodes

    NASA Technical Reports Server (NTRS)

    Shaw, Harry C.

    2007-01-01

    Rapid identification of pathogenic bacterial species is an important factor in combating public health problems such as E. coli contamination. Food and waterborne pathogens account for sickness in 76 million people annually (CDC). Diarrheagenic E. coli is a major source of gastrointestinal illness. Severe sepsis and Septicemia within the hospital environment are also major problems. 75 1,000 cases annually with a 30-50% mortality rate (Crit Care Med, July '01, Vol. 29, 1303-10). Patient risks run the continuum from fever to organ failure and death. Misdiagnosis or inappropriate treatment increases mortality. There exists a need for rapid screening of samples for identification of pathogenic species (Certain E. coli strains are essential for health). Critical to the identification process is the ability to isolate analytes of interest rapidly. This poster discusses novel devices for the separation of particles on the basis of the dielectric properties, mass and surface charge characteristics is presented. Existing designs involve contact between electrode surfaces and analyte medium resulting in contamination of the electrode bearing elements Two different device designs using different bulk micromachining MEMS processes (PolyMUMPS and a PyrexBIGold electrode design) are presented. These designs cover a range of particle sizes from small molecules through eucaryotic cells. The application of separation of bacteria is discussed in detail. Simulation data for electrostatic and microfluidic characteristics are provided. Detailed design characteristics and physical features of the as fabricated PolyMUMPS design are provided. Analysis of the simulation data relative to the expected performance of the devices will be provided and subsequent conclusions discussed.

  4. X-ray absorption near-edge structure study on positive electrodes of degraded lithium-ion battery

    NASA Astrophysics Data System (ADS)

    Shikano, Masahiro; Kobayashi, Hironori; Koike, Shinji; Sakaebe, Hikari; Saito, Yoshiyasu; Hori, Hironobu; Kageyama, Hiroyuki; Tatsumi, Kuniaki

    18650-type cylindrical cells using LiNi 1/3Mn 1/3Co 1/3O 2 (NMC) and hard carbon as positive and negative electrode material, respectively, were fabricated and degraded by cycle tests. The capacity of the cells remained more than 95% and 85% after cycle tests at 25 and 50 °C, respectively. After the cycle tests, Li-deficient cubic phase was observed on the surface of NMC. This phenomenon should be related to the degradation mechanism of this type of cell.

  5. Plasma parameters and existence conditions of monolayer dust structures in the electrode sheath of an RF discharge

    SciTech Connect

    Vaulina, O. S.; Vasilieva, E. V.; Timirkhanov, R. A.

    2011-12-15

    The plasma parameters in the electrode sheath of an RF discharge were studied experimentally under the conditions of dust monolayer levitation. A new method is proposed for determining the plasma parameters, such as the average electric field, ion density, and ion velocity. The screening parameter and the dust grain charge are estimated. The criteria of stable levitation of a dust monolayer are considered. The obtained results are compared with the available theoretical and numerical data, as well as with the results obtained using other diagnostic methods.

  6. (Metal-Organic Framework)-Polyaniline sandwich structure composites as novel hybrid electrode materials for high-performance supercapacitor

    NASA Astrophysics Data System (ADS)

    Guo, ShuaiNan; Zhu, Yong; Yan, YunYun; Min, YuLin; Fan, JinChen; Xu, QunJie; Yun, Hong

    2016-06-01

    Carbonized Zn-(Metal-Organic Framework)MOF- polyaniline composites for high performance of supercapacitor have been developed from zinc acetate, 8-Hydroxyquinoline, and aniline via a simple process. The as-synthesized product has been characterized by X-ray powder diffraction (XRD), Scanning electron microscopy(SEM), Fourier transform infrared spectra (FT-IR), Transmission electron microscope (TEM). The electrochemical properties of carbonized Zn-MOF/polyaniline electrode were investigated by current charge-discharge and cyclic voltammetry. The specific capacitance of MOF/PANI has been approach to be as high as 477 F g-1 at a current density of 1 A g-1.

  7. Use of Structure as a Basis for Abstraction in Air Traffic Control

    NASA Technical Reports Server (NTRS)

    Davison, Hayley J.; Hansman, R. John

    2004-01-01

    The safety and efficiency of the air traffic control domain is highly dependent on the capabilities and limitations of its human controllers. Past research has indicated that structure provided by the airspace and procedures could aid in simplifying the controllers cognitive tasks. In this paper, observations, interviews, voice command data analyses, and radar analyses were conducted at the Boston Terminal Route Control (TRACON) facility to determine if there was evidence of controllers using structure to simplify their cognitive processes. The data suggest that controllers do use structure-based abstractions to simplify their cognitive processes, particularly the projection task. How structure simplifies the projection task and the implications of understanding the benefits structure provides to the projection task was discussed.

  8. 78 FR 43184 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-19

    ...Under the provisions of the Federal Advisory Committee Act (FACA) of 1972 (5 U.S.C., Appendix, as amended), the Government in the Sunshine Act of 1976 (5 U.S.C. 552b, as amended), and 41 CFR 102-3.150, the Department of Defense (DoD) announces that the following Federal advisory committee meeting of the National Commission on the Structure of the Air Force (``the Commission'') will take...

  9. Graphene-based battery electrodes having continuous flow paths

    DOEpatents

    Zhang, Jiguang; Xiao, Jie; Liu, Jun; Xu, Wu; Li, Xiaolin; Wang, Deyu

    2014-05-24

    Some batteries can exhibit greatly improved performance by utilizing electrodes having randomly arranged graphene nanosheets forming a network of channels defining continuous flow paths through the electrode. The network of channels can provide a diffusion pathway for the liquid electrolyte and/or for reactant gases. Metal-air batteries can benefit from such electrodes. In particular Li-air batteries show extremely high capacities, wherein the network of channels allow oxygen to diffuse through the electrode and mesopores in the electrode can store discharge products.

  10. Method of forming a plasma sprayed interconnection layer on an electrode of an electrochemical cell

    DOEpatents

    Spengler, C.J.; Folser, G.R.; Vora, S.D.; Kuo, L.; Richards, V.L.

    1995-06-20

    A dense, substantially gas-tight, electrically conductive interconnection layer is formed on an air electrode structure of an electrochemical cell by (A) providing an electrode surface; (B) forming on a selected portion of the electrode surface, a layer of doped LaCrO{sub 3} particles doped with an element selected from Ca, Sr, Ba, Mg, Co, Ni, Al and mixtures thereof by plasma spraying doped LaCrO{sub 3} powder, preferably compensated with chromium as Cr{sub 2}O{sub 3} and/or dopant element, preferably by plasma arc spraying; and, (C) heating the doped and compensated LaCrO{sub 3} layer to about 1100 C to 1300 C to provide a dense, substantially gas-tight, substantially hydration-free, electrically conductive interconnection material bonded to the electrode surface. A solid electrolyte layer can be applied to the unselected portion of the air electrode, and a fuel electrode can be applied to the solid electrolyte, to provide an electrochemical cell. 6 figs.

  11. Method of forming a plasma sprayed interconnection layer on an electrode of an electrochemical cell

    DOEpatents

    Spengler, Charles J.; Folser, George R.; Vora, Shailesh D.; Kuo, Lewis; Richards, Von L.

    1995-01-01

    A dense, substantially gas-tight, electrically conductive interconnection layer is formed on an air electrode structure of an electrochemical cell by (A) providing an electrode surface; (B) forming on a selected portion of the electrode surface, a layer of doped LaCrO.sub.3 particles doped with an element selected from Ca, Sr, Ba, Mg, Co, Ni, Al and mixtures thereof by plasma spraying doped LaCrO.sub.3 powder, preferably compensated with chromium as Cr.sub.2 O.sub.3 and/or dopant element, preferably by plasma arc spraying; and, (C) heating the doped and compensated LaCrO.sub.3 layer to about 1100.degree. C. to 1300.degree. C. to provide a dense, substantially gas-tight, substantially hydration-free, electrically conductive interconnection material bonded to the electrode surface. A solid electrolyte layer can be applied to the unselected portion of the air electrode, and a fuel electrode can be applied to the solid electrolyte, to provide an electrochemical cell.

  12. Efficient and reusable polyamide-56 nanofiber/nets membrane with bimodal structures for air filtration.

    PubMed

    Liu, Bowen; Zhang, Shichao; Wang, Xueli; Yu, Jianyong; Ding, Bin

    2015-11-01

    Nanofibrous media that both possess high airborne particle interception efficiency and robust air permeability would have broad technological implications for areas ranging from individual protection and industrial security to environmental governance; however, creating such filtration media has proved extremely challenging. Here we report a strategy to construct the bio-based polyamide-56 nanofiber/nets (PA-56 NFN) membranes with bimodal structures for effective air filtration via one-step electrospinning/netting. The PA-56 membranes are composed of completely covered two-dimensional (2D) ultrathin (∼20 nm) nanonets which are optimized by facilely regulating the solution concentration, and the bonded scaffold fibers constructed cavity structures which are synchronously created by using the CH3COOH inspiration. With integrated properties of small aperture, high porosity, and bonded scaffold, the resulting PA-56 NFN membranes exhibit high filtration efficiency of 99.995%, low pressure drop of 111 Pa, combined with large dust holding capacity of 49 g/m(2) and dust-cleaning regeneration ability, for filtrating ultrafine airborne particles in the most safe manner involving sieving principle and surface filtration. The successful synthesis of PA-56 NFN medium would not only make it a promising candidate for air filtration, but also provide new insights into the design and development of nanonet-based bimodal structures for various applications.

  13. In Situ Electrochemical Synthesis and Deposition of Discotic Hexa-peri-hexabenzocoronene Molecules on Electrodes: Self-Assembled Structure, Redox Properties, and Application for Supercapacitor.

    PubMed

    Qin, Leiqiang; Zhang, Yunan; Wu, Xiaoyan; Nian, Li; Xie, Zengqi; Liu, Linlin; Ma, Yuguang

    2015-07-01

    Discotic hexa-peri-hexabenzocoronene (HBC) molecules are synthesized by electrochemical cyclodehydrogenation reaction and in situ self-assembled to π-electronic, discrete nanofibular objects with an average diameter about 70 nm, which are deposited directly onto the electrode. The nanofibers consist of columnar arrays of the π-stacked HBC molecules and the intercolumnar distance is determined to be 1.19 nm by X-ray diffraction, which corresponds well to the distance of 1.1 nm observed by high-resolution transmitting electron microscopy. The diameter of the molecular columns matches the size of the discotic HBC molecule indicating face-to-face π-stacking of HBC units in the column. The HBC nanofibers on electrode are redox active, and the nanosized columnar structures provide a huge surface area, which is a great benefit for the charging/discharging process, delivering excellent capacitance of 155 F g(-1) . The described electrochemical deposition method shows great advantage for self-assembling the family of insoluble and structurally designable graphene-like nano materials, which constitutes an important step toward molecular electronics.

  14. Aircraft structural health monitoring system development: overview of the Air Force/Navy smart metallic structures program

    NASA Astrophysics Data System (ADS)

    Van Way, Craig B.; Kudva, Jayanth N.; Schoess, Jeffrey N.; Zeigler, Michael L.; Alper, James M.

    1995-05-01

    Significant progress in fulfilling the current joint Air Force/Navy `Smart Metallic Structures (SMS)' program primary objective, to demonstrate a viable structural health monitoring system (SHMS) for a large structural aircraft component, is presented. Structural health monitoring and its relation to current Force Management (FM) and Aircraft Structural Integrity Program (ASIP) procedures are first reviewed together with a brief status overview of the relevant sensor technologies (e.g. AE, fiber-optic, corrosion, etc.). Key features of the SHMS architecture are described for the selected F/A-18 bulkhead and T-38 wing spar structural demonstration articles, highlighting sensors, processors, data busses, hardware, and software. Results from acoustic monitoring of the program sub-element structural tests are presented in some detail along with a status review of the SHMS multiplex bus component hardware and software. Finally, structural requirements for an SHMS meeting minimum ASIP guidelines for damage detection are discussed along with foals for future testing and development of the SHMS under the SMS program.

  15. Metal-Air Batteries

    SciTech Connect

    Zhang, Jiguang; Bruce, Peter G.; Zhang, Gregory

    2011-08-01

    Metal-air batteries have much higher specific energies than most currently available primary and rechargeable batteries. Recent advances in electrode materials and electrolytes, as well as new designs on metal-air batteries, have attracted intensive effort in recent years, especially in the development of lithium-air batteries. The general principle in metal-air batteries will be reviewed in this chapter. The materials, preparation methods, and performances of metal-air batteries will be discussed. Two main metal-air batteries, Zn-air and Li-air batteries will be discussed in detail. Other type of metal-air batteries will also be described.

  16. CONDENSED MATTER: ELECTRONIC STRUCTURE, ELECTRICAL, MAGNETIC, AND OPTICAL PROPERTIES: A New Conducting Polymer Electrode for Organic Electroluminescence Devices

    NASA Astrophysics Data System (ADS)

    Qu, Shu; Peng, Jing-Cu

    2008-08-01

    Conducting polymer polydimethylsiloxane (PDMS) is studied for the high performance electrode of organic electroluminescence devices. A method to prepare the electrode consisting of a SiC thin film and PDMS is investigated. By using ultra thin SiC films with different thicknesses, the organic electroluminescence devices are obtained in an ultra vacuum system with the model device PDMS/SiC/PPV/Alq3, where PPV is poly para-phenylene vinylene and Alq3 is tris(8-hydroxyquinoline) aluminium. The capacitance-voltage (C - V), capacitance-frequency (C - F), current-voltage (I - V), radiation intensity-voltage (R - V) and luminance efficiency-voltage (E - V) measurements are systematically studied to investigate the conductivity, Fermi alignment and devices properties in organic semiconductors. Scanning Kelvin probe measurement shows that the work function ofPDMS/SiC anode with a 2.5-nm SiC over layer can be increased by as much as 0.28 eV, compared to the conventional ITO anode. The result is attributed to the charge transfer effect and ohmic contacts at the interface.

  17. Temporal and spatial structure of a runaway electron beam in air at atmospheric pressure

    SciTech Connect

    Levko, D.; Krasik, Ya. E.; Tarasenko, V. F.; Rybka, D. V.; Burachenko, A. G.

    2013-05-21

    The time- and spatial structure of a runaway electron beam generated in air at atmospheric pressure by a high-voltage pulse with a rise time of {approx}300 ps is studied experimentally and numerically. It is obtained that the duration of the runaway electron current is a few tens of picoseconds, and it can consist of two or many peaks. It is shown that the many-peak temporal structure of the beam is caused by the non-simultaneous appearance of several emission centers on the cathode edge.

  18. Research into acetone removal from air by biofiltration using a biofilter with straight structure plates

    PubMed Central

    Baltrėnas, Pranas; Zagorskis, Alvydas; Misevičius, Antonas

    2015-01-01

    The biological air treatment method is based on the biological destruction of organic compounds using certain cultures of microorganisms. This method is simple and may be applied in many branches of industry. The main element of biological air treatment devices is a filter charge. Tests were carried out using a new-generation laboratory air purifier with a plate structure. This purifier is called biofilter. The biofilter has a special system for packing material humidification which does not require additional energy inputs. In order to extend the packing material's durability, it was composed of thermally treated birch fibre. Pollutant (acetone) biodegradation occurred on thermally treated wood fibre in this research. According to the performed tests and the received results, the process of biodestruction was highly efficient. When acetone was passed through biofilter's packing material at 0.08 m s−1 rate, the efficiency of the biofiltration process was from 70% up to 90%. The species of bacteria capable of removing acetone vapour from the air, i.e. Bacillus (B. cereus, B. subtilis), Pseudomonas (P. aeruginosa, P. putida), Stapylococcus (S. aureus) and Rhodococcus sp., was identified in this study during the process of biofiltration. Their amount in the biological packing material changed from 1.6 × 107 to 3.7 × 1011 CFU g−1. PMID:26019659

  19. Polyvinyl Alcohol-derived carbon nanofibers/carbon nanotubes/sulfur electrode with honeycomb-like hierarchical porous structure for the stable-capacity lithium/sulfur batteries

    NASA Astrophysics Data System (ADS)

    Deng, Nanping; Kang, Weimin; Ju, Jingge; Fan, Lanlan; Zhuang, Xupin; Ma, Xiaomin; He, Hongsheng; Zhao, Yixia; Cheng, Bowen

    2017-04-01

    The honeycomb-like hierarchical porous carbon nanofibers (PCNFs)-carbon nanotubes (CNTs)-sulfur(S) composite electrode is successfully desgined and prepared through ball-milling and heating method, in which the PCNFs are carbonized from fibers in the membrane composed of Polyvinyl Alcohol and Polytetrafluoroethylene by electro-blown spinning technology. The prepared PCNFs-CNTs-S composite are regarded as cathode for lithium-sulfur battery. The tailored porous structure and CNTs in the composite facilitate construction of a high electrical conductive pathway and store more S/polysulfides, and the dissoluble loss of intermediate S species in electrolyte can also be restrained because of acidized PVA-based porous carbon nanofibers. Meanwhile, the porous strcucture and CNTs can effectively alleviate volume changes in battery cycling process. Moreover, the presence of LiNO3 in electrolyte helps the electrochemical oxidation of Li2S and LiNO3-derived surface film effectively suppresses the migration of soluble polysulfide to the Li anode surface. Therefore, the obtained PCNFs-CNTs-S cathode exhibits excellent performance in Li-S battery with a high initial discharge capacity as high as 1302.9 mAh g-1, and super stable capacity retention with 809.1 mAh g-1 after 300 cycles at the current density of 837.5 mA g-1 (0.5 C). And the rate capability of PCNFs-CNTs-S electrode is much better than those of CNTs-S and PCNFs-S electrodes.

  20. Impact of Operating Context on the Use of Structure in Air Traffic Controller Cognitive Processes

    NASA Technical Reports Server (NTRS)

    Davison, Hayley J.; Histon, Jonathan M.; Ragnarsdottir, Margret Dora; Major, Laura M.; Hansman, R. John

    2004-01-01

    This paper investigates the influence of structure on air traffic controllers cognitive processes in the TRACON, En Route, and Oceanic environments. Radar data and voice command analyses were conducted to support hypotheses generated through observations and interviews conducted at the various facilities. Three general types of structure-based abstractions (standard flows, groupings, and critical points) have been identified as being used in each context, though the details of their application varied in accordance with the constraints of the particular operational environment. Projection emerged as a key cognitive process aided by the structure-based abstractions, and there appears to be a significant difference between how time-based versus spatial-based projection is performed by controllers. It is recommended that consideration be given to the value provided by the structure-based abstractions to the controller as well as to maintain consistency between the type (time or spatial) of information support provided to the controller.

  1. Force Structure: Performance Measures Needed to Better Implement the Recommendations of the National Commission on the Structure of the Air Force

    DTIC Science & Technology

    2016-05-01

    Study In January 2014, the National Commission on the Structure of the Air Force (commission) issued its report, which included 42 recommendations...for improving how the Air Force manages its total force. The report also discussed the feasibility of shifting 36,600 personnel from the active to...documentation and interviewed officials in order to describe the Air Force’s process for assessing its active and reserve component mix. What GAO

  2. Negative electrodes for lithium cells and batteries

    DOEpatents

    Vaughey, John T.; Fransson, Linda M.; Thackeray, Michael M.

    2005-02-15

    A negative electrode is disclosed for a non-aqueous electrochemical cell. The electrode has an intermetallic compound as its basic structural unit with the formula M.sub.2 M' in which M and M' are selected from two or more metal elements including Si, and the M.sub.2 M' structure is a Cu.sub.2 Sb-type structure. Preferably M is Cu, Mn and/or Li, and M' is Sb. Also disclosed is a non-aqueous electrochemical cell having a negative electrode of the type described, an electrolyte and a positive electrode. A plurality of cells may be arranged to form a battery.

  3. Coal mining activities change plant community structure due to air pollution and soil degradation.

    PubMed

    Pandey, Bhanu; Agrawal, Madhoolika; Singh, Siddharth

    2014-10-01

    The aim of this study was to investigate the effects of coal mining activities on the community structures of woody and herbaceous plants. The response of individual plants of community to defilement caused by coal mining was also assessed. Air monitoring, soil physico-chemical and phytosociological analyses were carried around Jharia coalfield (JCF) and Raniganj coalfield. The importance value index of sensitive species minified and those of tolerant species enhanced with increasing pollution load and altered soil quality around coal mining areas. Although the species richness of woody and herbaceous plants decreased with higher pollution load, a large number of species acclimatized to the stress caused by the coal mining activities. Woody plant community at JCF was more affected by coal mining than herbaceous community. Canonical correspondence analysis revealed that structure of herbaceous community was mainly driven by soil total organic carbon, soil nitrogen, whereas woody layer community was influenced by sulphur dioxide in ambient air, soil sulphate and soil phosphorus. The changes in species diversity observed at mining areas indicated an increase in the proportion of resistant herbs and grasses showing a tendency towards a definite selection strategy of ecosystem in response to air pollution and altered soil characteristics.

  4. Nitrogen-doped amorphous carbon-silicon core-shell structures for high-power supercapacitor electrodes

    NASA Astrophysics Data System (ADS)

    Tali, S. A. Safiabadi; Soleimani-Amiri, S.; Sanaee, Z.; Mohajerzadeh, S.

    2017-02-01

    We report successful deposition of nitrogen-doped amorphous carbon films to realize high-power core-shell supercapacitor electrodes. A catalyst-free method is proposed to deposit large-area stable, highly conformal and highly conductive nitrogen-doped amorphous carbon (a-C:N) films by means of a direct-current plasma enhanced chemical vapor deposition technique (DC-PECVD). This approach exploits C2H2 and N2 gases as the sources of carbon and nitrogen constituents and can be applied to various micro and nanostructures. Although as-deposited a-C:N films have a porous surface, their porosity can be significantly improved through a modification process consisting of Ni-assisted annealing and etching steps. The electrochemical analyses demonstrated the superior performance of the modified a-C:N as a supercapacitor active material, where specific capacitance densities as high as 42 F/g and 8.5 mF/cm2 (45 F/cm3) on silicon microrod arrays were achieved. Furthermore, this supercapacitor electrode showed less than 6% degradation of capacitance over 5000 cycles of a galvanostatic charge-discharge test. It also exhibited a relatively high energy density of 2.3 × 103 Wh/m3 (8.3 × 106 J/m3) and ultra-high power density of 2.6 × 108 W/m3 which is among the highest reported values.

  5. Nitrogen-doped amorphous carbon-silicon core-shell structures for high-power supercapacitor electrodes

    PubMed Central

    Tali, S. A. Safiabadi; Soleimani-Amiri, S.; Sanaee, Z.; Mohajerzadeh, S.

    2017-01-01

    We report successful deposition of nitrogen-doped amorphous carbon films to realize high-power core-shell supercapacitor electrodes. A catalyst-free method is proposed to deposit large-area stable, highly conformal and highly conductive nitrogen-doped amorphous carbon (a-C:N) films by means of a direct-current plasma enhanced chemical vapor deposition technique (DC-PECVD). This approach exploits C2H2 and N2 gases as the sources of carbon and nitrogen constituents and can be applied to various micro and nanostructures. Although as-deposited a-C:N films have a porous surface, their porosity can be significantly improved through a modification process consisting of Ni-assisted annealing and etching steps. The electrochemical analyses demonstrated the superior performance of the modified a-C:N as a supercapacitor active material, where specific capacitance densities as high as 42 F/g and 8.5 mF/cm2 (45 F/cm3) on silicon microrod arrays were achieved. Furthermore, this supercapacitor electrode showed less than 6% degradation of capacitance over 5000 cycles of a galvanostatic charge-discharge test. It also exhibited a relatively high energy density of 2.3 × 103 Wh/m3 (8.3 × 106 J/m3) and ultra-high power density of 2.6 × 108 W/m3 which is among the highest reported values. PMID:28186204

  6. Wearable Atmospheric Pressure Plasma Fabrics Produced by Knitting Flexible Wire Electrodes for the Decontamination of Chemical Warfare Agents

    NASA Astrophysics Data System (ADS)

    Jung, Heesoo; Seo, Jin Ah; Choi, Seungki

    2017-01-01

    One of the key reasons for the limited use of atmospheric pressure plasma (APP) is its inability to treat non-flat, three-dimensional (3D) surface structures, such as electronic devices and the human body, because of the rigid electrode structure required. In this study, a new APP system design—wearable APP (WAPP)—that utilizes a knitting technique to assemble flexible co-axial wire electrodes into a large-area plasma fabric is presented. The WAPP device operates in ambient air with a fully enclosed power electrode and grounded outer electrode. The plasma fabric is flexible and lightweight, and it can be scaled up for larger areas, making it attractive for wearable APP applications. Here, we report the various plasma properties of the WAPP device and successful test results showing the decontamination of toxic chemical warfare agents, namely, mustard (HD), soman (GD), and nerve (VX) agents.

  7. Wearable Atmospheric Pressure Plasma Fabrics Produced by Knitting Flexible Wire Electrodes for the Decontamination of Chemical Warfare Agents.

    PubMed

    Jung, Heesoo; Seo, Jin Ah; Choi, Seungki

    2017-01-18

    One of the key reasons for the limited use of atmospheric pressure plasma (APP) is its inability to treat non-flat, three-dimensional (3D) surface structures, such as electronic devices and the human body, because of the rigid electrode structure required. In this study, a new APP system design-wearable APP (WAPP)-that utilizes a knitting technique to assemble flexible co-axial wire electrodes into a large-area plasma fabric is presented. The WAPP device operates in ambient air with a fully enclosed power electrode and grounded outer electrode. The plasma fabric is flexible and lightweight, and it can be scaled up for larger areas, making it attractive for wearable APP applications. Here, we report the various plasma properties of the WAPP device and successful test results showing the decontamination of toxic chemical warfare agents, namely, mustard (HD), soman (GD), and nerve (VX) agents.

  8. Wearable Atmospheric Pressure Plasma Fabrics Produced by Knitting Flexible Wire Electrodes for the Decontamination of Chemical Warfare Agents

    PubMed Central

    Jung, Heesoo; Seo, Jin Ah; Choi, Seungki

    2017-01-01

    One of the key reasons for the limited use of atmospheric pressure plasma (APP) is its inability to treat non-flat, three-dimensional (3D) surface structures, such as electronic devices and the human body, because of the rigid electrode structure required. In this study, a new APP system design—wearable APP (WAPP)—that utilizes a knitting technique to assemble flexible co-axial wire electrodes into a large-area plasma fabric is presented. The WAPP device operates in ambient air with a fully enclosed power electrode and grounded outer electrode. The plasma fabric is flexible and lightweight, and it can be scaled up for larger areas, making it attractive for wearable APP applications. Here, we report the various plasma properties of the WAPP device and successful test results showing the decontamination of toxic chemical warfare agents, namely, mustard (HD), soman (GD), and nerve (VX) agents. PMID:28098192

  9. Structure of phospholipid monolayers containing poly(ethylene glycol) lipids at the air-water interface

    SciTech Connect

    Majewski, J.; Smith, G.S.; Kuhl, T.L.; Israelachvili, J.N.; Gerstenberg, M.C.

    1997-04-17

    The density distribution of a lipid monolayer at the air-water interface mixed with varying amounts of lipid with poly(ethylene glycol)polymer headgroups (polymer-lipid or PEG-lipid) was measured using neutron reflectometry. The structure of the monolayer at the interface was greatly perturbed by the presence of the bulky polymer-lipid headgroups resulting in a large increase in the thickness of the headgroup region normal to the interface and a systematic roughening of the interface with increasing polymer-lipid content. These results show how bulky hydrophilic moieties cause significant deformations and out-of-place protrusions of phospholipid monolayers and presumably bilayers, vesicles and biological membranes. In terms of polymer physics, very short polymer chains tethered to the air-water interface follow scaling behavior with a mushroom to brush transition with increasing polymer grafting density. 34 refs., 9 figs., 1 tab.

  10. Band structures of two dimensional solid/air hierarchical phononic crystals

    NASA Astrophysics Data System (ADS)

    Xu, Y. L.; Tian, X. G.; Chen, C. Q.

    2012-06-01

    The hierarchical phononic crystals to be considered show a two-order “hierarchical” feature, which consists of square array arranged macroscopic periodic unit cells with each unit cell itself including four sub-units. Propagation of acoustic wave in such two dimensional solid/air phononic crystals is investigated by the finite element method (FEM) with the Bloch theory. Their band structure, wave filtering property, and the physical mechanism responsible for the broadened band gap are explored. The corresponding ordinary phononic crystal without hierarchical feature is used for comparison. Obtained results show that the solid/air hierarchical phononic crystals possess tunable outstanding band gap features, which are favorable for applications such as sound insulation and vibration attenuation.

  11. On the influence of polarization effects in predicting the interfacial structure and capacitance of graphene-like electrodes in ionic liquids

    SciTech Connect

    Paek, Eunsu; Pak, Alexander J.; Hwang, Gyeong S.

    2015-01-14

    The electric double layer (C{sub D}) and electrode quantum (C{sub Q}) capacitances of graphene-based supercapacitors are investigated using a combined molecular dynamics and density functional theory approach. In particular, we compare an approach that includes electronic polarization to one that is polarization-free by evaluating both C{sub D} and C{sub Q} using [EMIM][BF{sub 4}] ionic liquid as a model electrolyte. Our results indicate that the inclusion of polarization effects can yield higher C{sub D} values—in this study by up to 40% around ±2 V—which we attribute primarily to the presence of charge smearing at the electrode-electrolyte interface. On the other hand, we find that the polarization-induced distortion of the electronic structure of graphene does not noticeably alter the predicted C{sub Q}. Our analysis suggests that an accurate description of the spatial charge distribution at the graphene interface due to polarization is necessary to improve our predictive capabilities, though more notably for C{sub D}. However, the conventional polarization-free approximation can serve as an efficient tool to study trends associated with both the C{sub Q} and C{sub D} at the interface of various graphene-like materials.

  12. An analysis of electrochemical energy storage using electrodes fabricated from atomically thin 2D structures of MoS2, graphene and MoS2/graphene composites

    NASA Astrophysics Data System (ADS)

    Huffstutler, Jacob D.

    The behavior of 2D materials has become of great interest in the wake of development of electrochemical double-layer capacitors (EDLCs) and the discovery of monolayer graphene by Geim and Novoselov. This study aims to analyze the response variance of 2D electrode materials for EDLCs prepared through the liquid-phase exfoliation method when subjected to differing conditions. Once exfoliated, samples are tested with a series of structural characterization methods, including tunneling electron microscopy, atomic force microscopy, Raman spectroscopy, and x-ray photoelectron spectroscopy. A new ionic liquid for EDLC use, 1-butyl-1-methylpyrrolidinium tris(pentafluoroethyl)trifluorophosphate is compared in performance to 6M potassium hydroxide aqueous electrolyte. Devices composed of liquid-phase exfoliated graphene / MoS2 composites are analyzed by concentration for ideal performance. Device performance under cold extreme temperatures for the ionic fluid is presented as well. A brief overview of by-layer analysis of graphene electrode materials is presented as-is. All samples were tested with cyclic voltammetry, galvanostatic charge-discharge, and electrochemical impedance spectroscopy, with good capacitive results. The evolution of electrochemical behavior through the altered parameters is tracked as well.

  13. Catalyzed enzyme electrodes

    DOEpatents

    Zawodzinski, Thomas A.; Wilson, Mahlon S.; Rishpon, Judith; Gottesfeld, Shimshon

    1993-01-01

    An enzyme electrode is prepared with a composite coating on an electrical conductor. The composite coating is formed from a casting solution of a perfluorosulfonic acid polymer, an enzyme, and a carbon supported catalyst. The solution may be cast directly on the conductor surface or may be formed as a membrane and applied to the surface. The perfluorosulfonic acid ionomer formed from the casting solution provides an insoluble biocompatible protective matrix for the enzyme and acts to retain the enzyme for long term availability in the electrode structure. The carbon supported catalyst provides catalytic sites throughout the layer for the oxidation of hydrogen peroxide from the enzyme reactions. The carbon support then provides a conductive path for establishing an electrical signal to the electrical conductor. In one embodiment, the electrical conductor is a carbon cloth that permits oxygen or other gas to be introduced to the perfluorosulfonic polymer to promote the enzyme reaction independent of oxygen in the solution being tested.

  14. Non-aqueous electrolytes for lithium-air batteries

    DOEpatents

    Amine, Khalil; Chen, Zonghai; Zhang, Zhengcheng

    2016-06-07

    A lithium-air cell includes a negative electrode; an air positive electrode; and a non-aqueous electrolyte which includes an anion receptor that may be represented by one or more of the formulas. ##STR00001##

  15. 3D Ordered Mesoporous Bifunctional Oxygen Catalyst for Electrically Rechargeable Zinc-Air Batteries.

    PubMed

    Park, Moon Gyu; Lee, Dong Un; Seo, Min Ho; Cano, Zachary Paul; Chen, Zhongwei

    2016-05-01

    To enhance energy efficiency and durability, a highly active and durable 3D ordered mesoporous cobalt oxide framework has been developed for rechargeable zinc-air batteries. The bifunctional air electrode consisting of 3DOM Co3 O4 having high active surface area and robust structure, results in superior charge and discharge battery voltages, and durable performance for electrically rechargeable zinc-air batteries.

  16. resterilizable electrode for electrosurgery

    NASA Technical Reports Server (NTRS)

    Engstrom, E. R.; Houge, J. C.

    1979-01-01

    Required properties of flexibility, electrical conductivity, tensile strength, and tear resistance of electrosurgical electrodes is retained through utilization of flexible-polymer/conductive particle composites for electrodes.

  17. Low circumferential voltage gradient self supporting electrode for solid oxide fuel cells

    DOEpatents

    Reichner, Philip

    1989-01-01

    The porous, self-supporting, elongated electrode is made, having at least two chambers through its axial length, the chambers separated by an electronically conductive member. This electrode can be an air electrode of a fuel cell, having a superimposed solid electrolyte and fuel electrode.

  18. Quantum dot-sensitized solar cells having 3D-TiO2 flower-like structures on the surface of titania nanorods with CuS counter electrode

    NASA Astrophysics Data System (ADS)

    Buatong, Nattha; Tang, I.-Ming; Pon-On, Weeraphat

    2015-03-01

    The photovoltaic performance of a quantum dot (QD)-sensitized solar cell consisting of CdS/CdSe/ZnS QDs loaded onto the surface of the three-dimensional (3D) flower-like TiO2 structure grown on an array (1D) of TiO2 nanorods (FTiR) is studied. The flower-like structure on the rod-shaped titania was synthesized using a double-step hydrothermal process. The FTiR array exhibited a 3D/1D composite structure with a specific surface area of 81.87 m2/g. Using CuS as the counter electrode instead of Pt offers the best performance and leads to an increase in the conversion efficiency ( η). The efficiency of the CdS/CdSe/ZnS QD-loaded FTiR assembling CuS counter electrode cell improved from η = 2.715% ( Voc = 0.692 V, Jsc = 5.896 mA/cm2, FF = 0.665) to η = 0.703% ( Voc = 0.665 V, Jsc = 2.108 mA/cm2, FF = 0.501) for the QD-loaded FTiR assembling Pt counter electrode cell. These studies reveal a synergistically beneficial effect on the solar-to-current conversion of these QD-sensitized solar cells when a CuS counter electrode is used instead of the usual Pt counter electrode.

  19. Crystal Structure and Spin-Singlet State of the LixVOPO4 Insertion Electrode System with Alternating-Bond Chain

    NASA Astrophysics Data System (ADS)

    Onoda, Masashige; Ikeda, Satoshi

    2013-05-01

    The crystal structure and electronic properties of the triclinic LixVOPO4 insertion electrode system with 0.9≤ x ≤ 1 are explored through measurements of x-ray four-circle diffraction, magnetization, and electron paramagnetic resonance. For x = 0.95 at 295 K, the one-dimensional corner-sharing chain of distorted VO6 octahedra has the alternating V--V distances of 3.5986 and 3.6219 Å with mixed-valence states of V4+ and V5+. All of the compositions exhibit a one-dimensional paramagnetism at temperatures above Tc1 ≃ 15 K due to the compensation from V--O--V bond angles in spite of the bond alternation. They have a long-range order to spin-singlet states at Tc2 ≃ 10 K due to the alternating-exchange couplings, accompanied by spin-dimer fluctuations between Tc1 and Tc2.

  20. AirCRED : the rationale and structure of a tool for estimating air pollutant reduction credits for alternative fuel vehicles.

    SciTech Connect

    Saricks, C. L.; Energy Systems

    2002-01-01

    Primarily to assist the U.S. Department of Energy's Clean Cities coalitions in estimating the net benefits of reducing air pollutant emissions gained by acquiring original equipment manufacture (OEM) alternativefuel vehicles (AFVs), Argonne National Laboratory has developed a graphical user interface-based benefit calculation model called AirCred. The application of this modeling tool has been extended to the estimation of state implementation plan credits for AFVs that may be claimed in nonattainment and maintenance regions for ozone and carbon monoxide. The tool also has been approved for and applied to the quantification of projected program benefits in applications for grant support to purchase OEM AFVs under the U.S. Department of Transportation's Congestion Mitigation and Air Quality Program. First, the model's founding principles and relatively simple mechanics are presented, accompanied by graphic displays of data input screens and comparative results for various vehicular categories. Current and future plans are cited for enhancement of the tool, including its respecification for consistency with MOBILE6 and for air planning in the yet-to-be-designated nonattainment areas for ambient particulate matter of 2.5 {mu}m and smaller. Then some issues and controversies about how and where AirCred should be applied are chronicled. Finally, some example applications are presented to illustrate the residual benefits of AFVs over time relative to their conventionally fueled counterparts of the same (recent) model year. Results indicate that AFVs of certain categories will remain viable and attractive candidates for reducing air emissions in ozone and carbon monoxide air quality control regions well into the future.

  1. Research on rechargeable oxygen electrodes

    NASA Technical Reports Server (NTRS)

    Giner, J.; Malachesky, P. A.; Holleck, G.

    1971-01-01

    Studies were carried out on a number of factors which may influence the behavior of the platinum electrocatalyst of oxygen electrodes for use in rechargeable metal-oxygen batteries or hydrogen-oxygen fuel cells. The effects of pretreatments for various potentials and added ionic species, which could be present in such systems, were studied with reguard to: (1) the state of surface oxidation, (2) platinum dissolution, (3) the kinetics of oxygen evolution and reduction (including the role of hydrogen peroxide), and (4) changes in porous electrode structure. These studies were carried out on smooth platinum, platinized platinum, and Teflon-bonded platinum black electrodes in carefully purified electrolyte solutions. The main factors which appear to affect rechargeable oxygen electrode performance and life are: (1) the buildup of a refractory anodic layer on extended cycling, and (2) the dissolution of platinum.

  2. Theoretical exploration of various lithium peroxide crystal structures in a Li-air battery

    SciTech Connect

    Lau, Kah; Qiu, Dantong; Luo, Xiangyi; Greeley, Jeffrey; Curtiss, Larry; Lu, Jun; Amine, Khalil

    2015-01-14

    We describe a series of metastable Li₂O₂ crystal structures involving different orientations and displacements of the O₂²⁻ peroxy ions based on the known Li₂O₂ crystal structure. Within the vicinity of the chemical potential ΔG ~ 0.20 eV/Li from the thermodynamic ground state of the Li₂O₂ crystal structure (i.e., Föppl structure), all of these newly found metastable Li₂O₂ crystal structures are found to be insulating and high-k materials, and they have a common unique signature of an O₂²⁻ O-O vibration mode (ω ~ 799–865 cm⁻¹), which is in the range of that commonly observed in Li-air battery experiments, regardless of the random O₂²⁻ orientations and the symmetry in the crystal lattice. From XRD patterns analysis, the commercially available Li₂O₂ powder is confirmed to be the thermodynamic ground state Föppl-like structure. However, for Li₂O₂ compounds that are grown electrochemically under the environment of Li-O₂ cells, we found that the XRD patterns alone are not sufficient for structural identification of these metastable Li₂O₂ crystalline phases due to the poor crystallinity of the sample. In addition, the commonly known Raman signal of O₂²⁻ vibration mode is also found to be insufficient to validate the possible existence of these newly predicted Li₂O₂ crystal structures, as all of them similarly share the similar O₂²⁻ vibration mode. However considering that the discharge voltage in most Li-O₂ cells are typically several tenths of an eV below the thermodynamic equilibrium for the formation of ground state Föppl structure, the formation of these metastable Li₂O₂ crystal structures appears to be thermodynamically feasible.

  3. Theoretical exploration of various lithium peroxide crystal structures in a Li-air battery

    DOE PAGES

    Lau, Kah; Qiu, Dantong; Luo, Xiangyi; ...

    2015-01-14

    We describe a series of metastable Li₂O₂ crystal structures involving different orientations and displacements of the O₂²⁻ peroxy ions based on the known Li₂O₂ crystal structure. Within the vicinity of the chemical potential ΔG ~ 0.20 eV/Li from the thermodynamic ground state of the Li₂O₂ crystal structure (i.e., Föppl structure), all of these newly found metastable Li₂O₂ crystal structures are found to be insulating and high-k materials, and they have a common unique signature of an O₂²⁻ O-O vibration mode (ω ~ 799–865 cm⁻¹), which is in the range of that commonly observed in Li-air battery experiments, regardless of themore » random O₂²⁻ orientations and the symmetry in the crystal lattice. From XRD patterns analysis, the commercially available Li₂O₂ powder is confirmed to be the thermodynamic ground state Föppl-like structure. However, for Li₂O₂ compounds that are grown electrochemically under the environment of Li-O₂ cells, we found that the XRD patterns alone are not sufficient for structural identification of these metastable Li₂O₂ crystalline phases due to the poor crystallinity of the sample. In addition, the commonly known Raman signal of O₂²⁻ vibration mode is also found to be insufficient to validate the possible existence of these newly predicted Li₂O₂ crystal structures, as all of them similarly share the similar O₂²⁻ vibration mode. However considering that the discharge voltage in most Li-O₂ cells are typically several tenths of an eV below the thermodynamic equilibrium for the formation of ground state Föppl structure, the formation of these metastable Li₂O₂ crystal structures appears to be thermodynamically feasible.« less

  4. Numerical simulation of the fluid-structure interaction between air blast waves and soil structure

    NASA Astrophysics Data System (ADS)

    Umar, S.; Risby, M. S.; Albert, A. Luthfi; Norazman, M.; Ariffin, I.; Alias, Y. Muhamad

    2014-03-01

    Normally, an explosion threat on free field especially from high explosives is very dangerous due to the ground shocks generated that have high impulsive load. Nowadays, explosion threats do not only occur in the battlefield, but also in industries and urban areas. In industries such as oil and gas, explosion threats may occur on logistic transportation, maintenance, production, and distribution pipeline that are located underground to supply crude oil. Therefore, the appropriate blast resistances are a priority requirement that can be obtained through an assessment on the structural response, material strength and impact pattern of material due to ground shock. A highly impulsive load from ground shocks is a dynamic load due to its loading time which is faster than ground response time. Of late, almost all blast studies consider and analyze the ground shock in the fluid-structure interaction (FSI) because of its influence on the propagation and interaction of ground shock. Furthermore, analysis in the FSI integrates action of ground shock and reaction of ground on calculations of velocity, pressure and force. Therefore, this integration of the FSI has the capability to deliver the ground shock analysis on simulation to be closer to experimental investigation results. In this study, the FSI was implemented on AUTODYN computer code by using Euler-Godunov and the arbitrary Lagrangian-Eulerian (ALE). Euler-Godunov has the capability to deliver a structural computation on a 3D analysis, while ALE delivers an arbitrary calculation that is appropriate for a FSI analysis. In addition, ALE scheme delivers fine approach on little deformation analysis with an arbitrary motion, while the Euler-Godunov scheme delivers fine approach on a large deformation analysis. An integrated scheme based on Euler-Godunov and the arbitrary Lagrangian-Eulerian allows us to analyze the blast propagation waves and structural interaction simultaneously.

  5. Evolution of porous silicon crystal structure during storage in ambient air

    NASA Astrophysics Data System (ADS)

    Sorokin, L. M.; Ratnikov, V. V.; Kalmykov, A. E.; Sokolov, V. I.

    2010-02-01

    Both double- and triple- crystal X-ray diffraction techniques (X-ray DCD and TCD techniques) together with transmission electron microscopy (TEM) were employed for the investigation of structural changes in porous silicon (PS) layers during prolonged periods (up to 6800 hours) of their storage in ambient air. Apart from the Bragg reflection from the Si substrate, the diffraction pattern contains an additional maximum caused by the presence of the PS layer with an increased lattice parameter. The position of this peak shifts to smaller Bragg angles and its intensity decreases as the time of storage in air increases. In addition, the profiles of such peaks become clearly asymmetric. In this case, Gaussian curves were used to reach a fit to the experimental X-ray rocking curves. All samples were biaxially bent due to compressive stresses that arise as soon as 10 min after electrochemical process. The values of lattice strains along the surface normal (Δd/d)⊥ and lateral deformation (Δd/d)|| were estimated to be ~ +10-3, ~ -10-5 respectively. The analysis of diffraction curve evolution shows a gradual destruction of the crystal lattice caused by the air oxidation process.

  6. Morphological bubble evolution induced by air diffusion on submerged hydrophobic structures

    NASA Astrophysics Data System (ADS)

    Lv, Pengyu; Xiang, Yaolei; Xue, Yahui; Lin, Hao; Duan, Huiling

    2017-03-01

    Bubbles trapped in the cavities always play important roles in the underwater applications of structured hydrophobic surfaces. Air exchange between bubbles and surrounding water has a significant influence on the morphological bubble evolution, which in turn frequently affects the functionalities of the surfaces, such as superhydrophobicity and drag reduction. In this paper, air diffusion induced bubble evolution on submerged hydrophobic micropores under reduced pressures is investigated experimentally and theoretically. The morphological behaviors of collective and single bubbles are observed using confocal microscopy. Four representative evolution phases of bubbles are captured in situ. After depressurization, bubbles will not only grow and coalesce but also shrink and split although the applied pressure remains negative. A diffusion-based model is used to analyze the evolution behavior and the results are consistent with the experimental data. A criterion for bubble growth and shrinkage is also derived along with a phase diagram, revealing that the competition of effective gas partial pressures across the two sides of the diffusion layer dominates the bubble evolution process. Strategies for controlling the bubble evolution behavior are also proposed based on the phase diagram. The current work provides a further understanding of the general behavior of bubble evolution induced by air diffusion and can be employed to better designs of functional microstructured hydrophobic surfaces.

  7. Structure and Stability of One-Dimensional Detonations in Ethylene-Air Mixtures

    NASA Technical Reports Server (NTRS)

    Yungster, S.; Radhakrishnan, K.; Perkins, High D. (Technical Monitor)

    2003-01-01

    The propagation of one-dimensional detonations in ethylene-air mixtures is investigated numerically by solving the one-dimensional Euler equations with detailed finite-rate chemistry. The numerical method is based on a second-order spatially accurate total-variation-diminishing scheme and a point implicit, first-order-accurate, time marching algorithm. The ethylene-air combustion is modeled with a 20-species, 36-step reaction mechanism. A multi-level, dynamically adaptive grid is utilized, in order to resolve the structure of the detonation. Parametric studies over an equivalence ratio range of 0.5 less than phi less than 3 for different initial pressures and degrees of detonation overdrive demonstrate that the detonation is unstable for low degrees of overdrive, but the dynamics of wave propagation varies with fuel-air equivalence ratio. For equivalence ratios less than approximately 1.2 the detonation exhibits a short-period oscillatory mode, characterized by high-frequency, low-amplitude waves. Richer mixtures (phi greater than 1.2) exhibit a low-frequency mode that includes large fluctuations in the detonation wave speed; that is, a galloping propagation mode is established. At high degrees of overdrive, stable detonation wave propagation is obtained. A modified McVey-Toong short-period wave-interaction theory is in excellent agreement with the numerical simulations.

  8. Quantifying protein adsorption and function at nanostructured materials: enzymatic activity of glucose oxidase at GLAD structured electrodes.

    PubMed

    Jensen, Uffe B; Ferapontova, Elena E; Sutherland, Duncan S

    2012-07-31

    Nanostructured materials strongly modulate the behavior of adsorbed proteins; however, the characterization of such interactions is challenging. Here we present a novel method combining protein adsorption studies at nanostructured quartz crystal microbalance sensor surfaces (QCM-D) with optical (surface plasmon resonance SPR) and electrochemical methods (cyclic voltammetry CV) allowing quantification of both bound protein amount and activity. The redox enzyme glucose oxidase is studied as a model system to explore alterations in protein functional behavior caused by adsorption onto flat and nanostructured surfaces. This enzyme and such materials interactions are relevant for biosensor applications. Novel nanostructured gold electrode surfaces with controlled curvature were fabricated using colloidal lithography and glancing angle deposition (GLAD). The adsorption of enzyme to nanostructured interfaces was found to be significantly larger compared to flat interfaces even after normalization for the increased surface area, and no substantial desorption was observed within 24 h. A decreased enzymatic activity was observed over the same period of time, which indicates a slow conformational change of the adsorbed enzyme induced by the materials interface. Additionally, we make use of inherent localized surface plasmon resonances in these nanostructured materials to directly quantify the protein binding. We hereby demonstrate a QCM-D-based methodology to quantify protein binding at complex nanostructured materials. Our approach allows label free quantification of protein binding at nanostructured interfaces.

  9. A comparative insight of potassium vanadates as positive electrode materials for Li batteries: influence of the long-range and local structure.

    PubMed

    Baddour-Hadjean, Rita; Boudaoud, Arezki; Bach, Stéphane; Emery, Nicolas; Pereira-Ramos, Jean-Pierre

    2014-02-03

    Potassium vanadates with ratio K/V = 1:3, 1:4, and 1:8, prepared by a fast and facile synthesis route, were investigated as positive electrode materials in lithium batteries. KV3O8 and K0.5V2O5 have layered structures, while K0.25V2O5 exhibits a tunnel framework isomorphic to that of β-Na0.33V2O5. The Raman spectra of KV3O8, K0.5V2O5, and K0.25V2O5 compounds are reported here for the first time, and a detailed comparative analysis distinguishes spectral patterns specific to each structural arrangement. The electrochemical performances of these potassium vanadates toward lithium insertion were investigated. The potassium-richer compound KV3O8 shows a good rechargeability in spite of a low discharge capacity of 70 mAh g(-1), while the potassium-poorer bronze K0.25V2O5 exhibits the highest specific capacity of 230 mAh g(-1) but a slow and continuous capacity fade with cycling. We demonstrate that the K0.5V2O5 compound, with its double-sheet V2O5 layered framework characterized by a large interlayer spacing of 7.7 Å, is the best candidate as positive electrode for lithium battery among the potassium-vanadium bronzes and oxides. A remarkable specific capacity of 210 mAh g(-1), combined with excellent capacity retention, is achieved.

  10. A scalable route to prepare core-shell structured ZnO@PEDOT nanowires and PEDOT nanotubes and their properties as electrode materials

    NASA Astrophysics Data System (ADS)

    Wang, Fang; Zhang, Xianhong; Yang, Le; Xu, Dehong; Ma, Yuhong; Chen, Dong; Wang, Li; Zhao, Changwen; Yang, Wantai

    2016-05-01

    A composite of a core-shell structured nanowires with ZnO as a core and conductive poly(3,4-ethylenedioxythiophene) (PEDOT) as a shell was prepared. At first, the hexagonal ZnO nanowires, with diameter of about 80-100 nm and length 4-5 μm, were fabricated by hydrothermal synthesis process. Then a thick layer of poly(trifluoroethyl methacrylate)-block-poly(sodium styrene sulfonate) (PTFEMA-b-PSSNa) was grafted from the surface of ZnO nanowires via atom transfer free radical polymerization. At last, with the ZnO@PTFEMA-b-PSSNa as a template and the PSSNa chain as the counterion dopant, PEDOT was precipitated onto the surface of the template to form the composite of ZnO@PEDOT/PSSNa. With the evaluation of the EDOT polymerization, the thickness of the PEDOT layer increased steadily. However, as the ratio of EDOT/ZnO was greater than 1:2, the ZnO nanowires templates were dissolved at last and then PEDOT particles were produced due to increasing of the acidity during the oxidation polymerization of EDOT. In this case, the product was the mixture of the nanotubes and particles of PEDOT/PPSNa. The electrochemical capacitances of the composites with different structures were investigated with cyclic voltammetry, galvanostatic charge-discharge and electrochemical impedance spectroscopy techniques with three-electrode cell configuration. The maximum specific capacitance of ZnO@PEDOT electrode can reach 101.34 F/g at 20 mV/s.

  11. A low-temperature fabricated gate-stack structure for Ge-based MOSFET with ferromagnetic epitaxial Heusler-alloy/Ge electrodes

    NASA Astrophysics Data System (ADS)

    Fujita, Yuichi; Yamada, Michihiro; Nagatomi, Yuta; Yamamoto, Keisuke; Yamada, Shinya; Sawano, Kentarou; Kanashima, Takeshi; Nakashima, Hiroshi; Hamaya, Kohei

    2016-06-01

    A possible low-temperature fabrication process of a gate-stack for Ge-based spin metal-oxide-semiconductor field-effect transistor (MOSFET) is investigated. First, since we use epitaxial ferromagnetic Heusler alloys on top of the phosphorous doped Ge epilayer as spin injector and detector, we need a dry etching process to form Heusler-alloy/n+-Ge Schottky-tunnel contacts. Next, to remove the Ge epilayers damaged by the dry etching process, the fabricated structures are dipped in a 0.03% diluted H2O2 solution. Finally, Al/SiO2/GeO2/Ge gate-stack structures are fabricated at 300 °C as a top gate-stack structure. As a result, the currents in the Ge-MOSFET fabricated here can be modulated by applying gate voltages even by using the low-temperature formed gate-stack structures. This low-temperature fabrication process can be utilized for operating Ge spin MOSFETs with a top gate electrode.

  12. First-Principles Studies on the Structural Stability of Spinel ZnCo2O4 as an Electrode Material for Lithium-ion Batteries

    PubMed Central

    Liu, Wei-Wei; Jin, M. T.; Shi, W. M.; Deng, J. G.; Lau, Woon-Ming; Zhang, Y. N.

    2016-01-01

    Systematic first principles calculations were performed for ZnCo2O4 to clarify its structural and electronic properties, and particularly the structural stability as an electrode material for lithium-ion batteries. For samples with low Li concentration, e.g., LinZnCo2O4 with n < 1, Li atoms take the center of oxygen octahedra and may diffuse rapidly. Structure distortions and volume expansions can be observed in LinZnCo2O4 with n > 1 and amorphous structures eventually prevail. The AIMD simulations for Li9ZnCo2O4 suggest the formation of Li2O, Co3O4 and LiZn local compounds or alloys. In particular, the formation of Zn-Co aggregations and the losing of ZnO pairs are identified as the possible reasons that are responsible to the Li capacity fading in ZnCo2O4 anodes. PMID:27827419

  13. Structural transformation during Li/Na insertion and theoretical cyclic voltammetry of the δ-NH4V4O10 electrode: a first-principles study.

    PubMed

    Sarkar, Tanmay; Kumar, Parveen; Bharadwaj, Mridula Dixit; Waghmare, Umesh

    2016-04-14

    A double layer δ-NH4V4O10, due to its high energy storage capacity and excellent rate capability, is a very promising cathode material for Li-ion and Na-ion batteries for large-scale renewable energy storage in transportation and smart grids. While it possesses better stability, and higher ionic and electronic conductivity than the most widely explored V2O5, the mechanisms of its cyclability are yet to be understood. Here, we present a theoretical cyclic voltammetry as a tool based on first-principles calculations, and uncover structural transformations that occur during Li(+)/Na(+) insertion (x) into (Lix/Nax)NH4V4O10. Structural distortions associated with single-phase and multi-phase structural changes during the insertion of Li(+)/Na(+), identified through the analysis of voltage profile and theoretical cyclic voltammetry are in agreement with the reported experimental electrochemical measurements on δ-NH4V4O10. We obtain an insight into its electronic structure with a lower band gap that is responsible for the high rate capability of (Lix/Nax) δ-NH4V4O10. The scheme of theoretical cyclic voltammetry presented here will be useful for addressing issues of cyclability and energy rate in other electrode materials.

  14. Electrically recharged battery employing a packed/spouted bed metal particle electrode

    DOEpatents

    Siu, Stanley C.; Evans, James W.; Salas-Morales, Juan

    1995-01-01

    A secondary metal air cell, employing a spouted/packed metal particle bed and an air electrode. More specifically a zinc air cell well suited for use in electric vehicles which is capable of being either electrically or hydraulically recharged.

  15. Influence of the Conditions of Electrode Position and Heat Treatment on the Structure and Properties of Metallic Coatings

    NASA Astrophysics Data System (ADS)

    Kovenskiy, I. M.; Kulemina, A. A.

    2016-04-01

    Influence of electrodeposition conditions and heat treatment on the structure and properties of metallic coatings has been considered. It has been that at different values of overvoltage, metals crystallize with a cellular, subgrain or monoblock structure. The final formation of the structure occurs during annealing, in the process of which either polygonization or recrystallization develops in the coatings. Varying the conditions of electrodeposition and heat treatment allows obtaining coatings with functional characteristics for specific operating conditions.

  16. Electrode porosity and effective electrocatalyst activity in electrode-membrane-assemblies (MEAs) of PEMFCs

    SciTech Connect

    Fischer, A.; Wendt, H.

    1996-12-31

    New production technologies of membrane-electrode-assemblies for PEWCs which ensure almost complete catalyst utilization by {open_quotes}wetting{close_quotes} the internal catalyst surface with the ionomeric electrolyte, allow for a reduction of Pt-loadings from prior 4 mg cm{sup -2} to now less than 0.5 mg cm{sup -2}. Such electrodes are not thicker than from 5 to 10 {mu}m. Little has been published hitherto about the detailed micromorphology of such electrodes and the role of electrode porosity on electrode performance. It is well known, that the porosity of thicker fuel cell electrodes, e.g. of PAFC or AFC electrodes is decisive for their performance. Therefore the issue of this investigation is to measure and to modify the porosity of electrodes prepared by typical MEA production procedures and to investigate the influence of this porosity on the effective catalyst activity for cathodic reduction of oxygen from air in membrane cells. It may be anticipated that any mass transfer hindrance of gaseous reactants into porous electrodes would manifest itself rather in the conversion of dilute gases than in the conversion of pure gases (e.g. neat oxygen). Therefore in this investigation the performance of membrane cell cathodes with non pressurized air had been compared to that with neat oxygen at cathodes which had a relatively low Pt-loading of 0.15 mg cm{sup -2}.

  17. Lithium-aluminum-magnesium electrode composition

    DOEpatents

    Melendres, Carlos A.; Siegel, Stanley

    1978-01-01

    A negative electrode composition is presented for use in a secondary, high-temperature electrochemical cell. The cell also includes a molten salt electrolyte of alkali metal halides or alkaline earth metal halides and a positive electrode including a chalcogen or a metal chalcogenide as the active electrode material. The negative electrode composition includes up to 50 atom percent lithium as the active electrode constituent and a magnesium-aluminum alloy as a structural matrix. Various binary and ternary intermetallic phases of lithium, magnesium, and aluminum are formed but the electrode composition in both its charged and discharged state remains substantially free of the alpha lithium-aluminum phase and exhibits good structural integrity.

  18. 78 FR 66903 - Meeting of the National Commission on the Structure of the Air Force

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-11-07

    ... functions including: Air Superiority, Air Mobility, Global Precision Attack, Nuclear Deterrence Operations... strategy. They will also address considerations for measuring and assessing Active, Reserve and...

  19. Conductance of p-n-p graphene structures with "air-bridge" top gates.

    PubMed

    Gorbachev, Roman V; Mayorov, Alexander S; Savchenko, Alexander K; Horsell, David W; Guinea, Francisco

    2008-07-01

    We have fabricated graphene devices with a top gate separated from the graphene layer by an air gap-a design which does not decrease the mobility of charge carriers under the gate. This gate is used to realize p-n-p structures where the conducting properties of chiral carriers are studied. The band profile of the structures is calculated taking into account the specifics of the graphene density of states and is used to find the resistance of the p-n junctions expected for chiral carriers. We show that ballistic p-n junctions have larger resistance than diffusive ones. This is caused by suppressed transmission of chiral carriers at angles away from the normal to the junction.

  20. AIRS-observed warm core structures of tropical cyclones over the western North Pacific

    NASA Astrophysics Data System (ADS)

    Gao, Si; Chen, Baiqing; Li, Tim; Wu, Naigeng; Deng, Wenjian

    2017-03-01

    Atmospheric Infrared Sounder (AIRS) temperature profiles during the period 2003-2013 are used to examine the warm core structures and evolution characteristics associated with the formation and development of western North Pacific (WNP) tropical cyclones (TCs). The warm core with a steady 1.5-K warming in the layer of 500-300 hPa occurs 24 h prior to tropical storm formation. Apparent eye warming extends upward to upper troposphere and downward to near surface after tropical storm formation. TC intensity shows a robust positive correlation with the warm core strength and has a weaker but still significant positive correlation with the warm core height (the weaker correlation is primarily attributed to the scattered warm core heights of weak TCs). Future 24-h intensity change of TCs has little correlation with the warm core height while it has a significant negative correlation with the warm core strength. Weak to moderate warm core at 500-200 hPa may be a necessary but not sufficient initial condition for TC rapid intensification. AIRS-observed warm core structures, in combination with other environmental factors, have the potential to improve the prediction of tropical storm formation and rapid intensification of WNP TCs.

  1. Three-dimensional multiscale analysis of degradation of nano- and micro-structure in direct methanol fuel cell electrodes after methanol starvation

    NASA Astrophysics Data System (ADS)

    Netzeband, Christian; Arlt, Tobias; Wippermann, Klaus; Lehnert, Werner; Manke, Ingo

    2016-09-01

    This study investigates the ageing effects on the microstructure of the anode catalyst layer of direct methanol fuel cells (DMFC) after complete methanol starvation. To this end the samples of two methanol-depleted membrane electrode assemblies (MEA) have been compared with a pristine reference sample. A three-dimensional characterization of the anode catalyst layer (ACL) structure on a nanometer scale has been conducted by focused ion beam (FIB)/scanning electron microscope (SEM) tomography. The FIB/SEM tomography allows for a detailed analysis of statistic parameters of micro-structured materials, such as porosity, tortuosity and pore size distributions. Furthermore, the SEM images displayed a high material contrast between the heavy catalyst metals (Pt/Ru) and the relatively light carbon support, which made it possible to map the catalyst distribution in the acquired FIB/SEM tomographies. Additional synchrotron X-ray tomographies have been conducted in order to obtain an overview of the structural changes of all the components of a section of the MEAs after methanol depletion.

  2. Influence of doping anions on structure and properties of electro-polymerized polypyrrole counter electrodes for use in dye-sensitized solar cells

    NASA Astrophysics Data System (ADS)

    Zhang, Xuehua; Wang, Shasha; Lu, Shan; Su, Jia; He, Tao

    2014-01-01

    The nature of doping anions in polymerization solution has great influences on structure and properties of electro-polymerized polypyrrole (PPy) films and, thereby, on the electrocatalytic activity for I-/I3- redox reaction and accordingly the performance of dye-sensitized solar cells (DSSCs) based on PPy counter electrodes (CEs). The ions of chloride (Cl-), sulfate (SO42-), p-toluene sulfonate (TsO-), and dodecyl benzene sulfonate (DBS-) have been used as counter anions to prepare PPy films as CEs in the DSSCs. Compared with inorganic anions (Cl- and SO42-), the organic ones (TsO- and DBS-) afford more delocalized polarons. Moreover, PPy-DBS- films have the most fibrous or porous structure. Thus, PPy-DSB- has plenty of electrocatalytic active sites and high electric conductivity and, thereby, high electrocatalytic activity for I-/I3- redox reaction. Due to the synergistic effects of fibrous/porous structure, high conductivity and low interfacial charge transfer impedance, PPy-DBS- CE based DSSCs show the best photovoltaic conversion efficiency up to 5.40%, reaching 88% of the DSSCs based on Pt CE. Our results indicate that PPy thin films are promising candidates to replace Pt as the CEs for DSSCs, especially for the future flexible devices.

  3. Ion-Selective Electrodes.

    ERIC Educational Resources Information Center

    Arnold, Mark A.; Meyerhoff, Mark E.

    1984-01-01

    Literature on ion-selective electrodes (ISEs) is reviewed in seven sections: books, conferences, reviews; potentiometric membrane electrodes; glass and solid-state membrane electrodes; liquid and polymer membrane ISEs; coated wire electrodes, ion-selective field effect transistors, and microelectrodes; gas sensors and selective bioelectrode…

  4. Structural and electrochemical stability of Li-rich layer structured Li2MoO3 in air

    NASA Astrophysics Data System (ADS)

    Ma, Jun; Gao, Yurui; Wang, Zhaoxiang; Chen, Liquan

    2014-07-01

    Li2MnO3 is an important component of the Li-rich Mn-based high-capacity cathode material for lithium ion batteries, xLi2MnO3·(1 - x)LiM‧O2 composites. Replacing Li2MnO3 with iso-structured Li2MoO3 is expected to improve the rate performance and suppress the oxygen release of the composites at high potentials due to the higher electric conductivity of Li2MoO3 and its more facile charge compensation (by Mo4+/Mo6+ redox) upon Li removal than that of Li2MnO3. As part of our series work on the Li2MoO3-based Li-rich layer structured cathode materials, this article is to study the structural and performance stability of Li2MoO3 in air. The obtained information will shed light on the development and application of xLi2MoO3·(1 - x)LiM‧O2 composite cathode materials though Li2MoO3 will not be applied as an independent cathode material.

  5. Structure and conformation of peptides at air/aqueous interface and their impact on interfacial water structure

    NASA Astrophysics Data System (ADS)

    Chandra Jena, Kailash; Tomar, Deepak

    Process of protein folding is very essential for the proper functioning of the protein molecules at membrane surface and other organelles. Understanding the process of protein folding at various biological relevant aqueous interfaces are very important to understand various complicated chemical and physical processes relevant to chemistry, physics, and medicine. The building blocks of proteins molecules are amino acids and the chemistry of each amino acid is very different; as a consequence their sequence plays an important role for various conformations upon adsorption for the protein molecules. In the present study, we have investigated the interfacial structure and conformation of two amino acids (L-Proline and L-Tyrosine) and peptide molecules formed from these two amino acids (L-Tyr-Pro). We have used sum frequency generation (SFG) vibrational spectroscopy to probe the air/aqueous interface. We have studied the impact of adsorption of the amino acids and the peptide molecules on the interfacial water structure by slowly varying concentration and ionic strength of the solutions. Our preliminary result shows a huge impact of the adsorption process of peptide molecules on the hydrogen bonding environment of interfacial structure of water. Indian Institute of Technology Ropar, Nangal Road, Rupnagar, Punjab-140001.

  6. Long Life Durability of Electrodes of Electrical Resistance Change Method for Damage Monitoring of CFRP Composite Structures

    DTIC Science & Technology

    2008-03-01

    to measure fatigue limit of the CFRP laminates. Figure 12 shows the results of the fatigue tests. The abscissa is the number of cycles to failure and...monitoring of CFRP composite structures 2007 April – 2008 March Professor Akira Todoroki Department of Mechanical Sciences and Engineering Tokyo...monitoring of CFRP composite structures 5a. CONTRACT NUMBER FA48690714039 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Akira Todoroki 5d

  7. Spinal cord electrophysiology II: extracellular suction electrode fabrication.

    PubMed

    Garudadri, Suresh; Gallarda, Benjamin; Pfaff, Samuel; Alaynick, William

    2011-02-20

    Development of neural circuitries and locomotion can be studied using neonatal rodent spinal cord central pattern generator (CPG) behavior. We demonstrate a method to fabricate suction electrodes that are used to examine CPG activity, or fictive locomotion, in dissected rodent spinal cords. The rodent spinal cords are placed in artificial cerebrospinal fluid and the ventral roots are drawn into the suction electrode. The electrode is constructed by modifying a commercially available suction electrode. A heavier silver wire is used instead of the standard wire given by the commercially available electrode. The glass tip on the commercial electrode is replaced with a plastic tip for increased durability. We prepare hand drawn electrodes and electrodes made from specific sizes of tubing, allowing consistency and reproducibility. Data is collected using an amplifier and neurogram acquisition software. Recordings are performed on an air table within a Faraday cage to prevent mechanical and electrical interference, respectively.

  8. HSPES membrane electrode assembly

    NASA Technical Reports Server (NTRS)

    Kindler, Andrew (Inventor); Yen, Shiao-Ping (Inventor)

    2000-01-01

    An improved fuel cell electrode, as well as fuel cells and membrane electrode assemblies that include such an electrode, in which the electrode includes a backing layer having a sintered layer thereon, and a non-sintered free-catalyst layer. The invention also features a method of forming the electrode by sintering a backing material with a catalyst material and then applying a free-catalyst layer.

  9. Improved performance of thermal-optic switch using polymer/silica hybrid and air trench waveguide structures.

    PubMed

    Liu, Yu-Fen; Wang, Xi-Bin; Sun, Jing-Wen; Sun, Jian; Wang, Fei; Chen, Chang-Ming; Sun, Xiao-Qiang; Cui, Zhan-Chen; Zhang, Da-Ming

    2015-05-01

    By exploiting the polymer/silica hybrid and the air trench waveguide structures, we demonstrate a new type of low-power consuming and high-speed thermal-optic (TO) switch. Such a design provides an effective means to shorten the switching time of the TO switches, as well as to reduce the power consumption at the same time. This TO switch operated with less than 150 μs of switching time via a polymer/silica hybrid waveguide structure. Meanwhile, the power consumption was reduced to be 3.4 mW by introducing the air trench structure.

  10. Influence of material structure on air-borne ultrasonic application in drying.

    PubMed

    Ozuna, César; Gómez Álvarez-Arenas, Tomás; Riera, Enrique; Cárcel, Juan A; Garcia-Perez, Jose V

    2014-05-01

    This work aims to contribute to the understanding of how the properties of the material being dried affect air-borne ultrasonic application. To this end, the experimental drying kinetics (40°C and 1m/s) of cassava (Manihot esculenta) and apple (Malus domestica var. Granny Smith) were carried out applying different ultrasonic powers (0, 6, 12, 19, 25 and 31 kW/m(3)). Furthermore, the power ultrasound-assisted drying kinetics of different fruits and vegetables (potato, eggplant, carrot, orange and lemon peel) already reported in previous studies were also analyzed. The structural, textural and acoustic properties of all these products were assessed, and the drying kinetics modeled by means of the diffusion theory. A significant linear correlation (r>0.95) was established between the identified effective diffusivity (DW) and the applied ultrasonic power for the different products. The slope of this relationship (SDUP) was used as an index of the effectiveness of the ultrasonic application; thus the higher the SDUP, the more effective the ultrasound application. SDUP was well correlated (r ⩾ 0.95) with the porosity and hardness. In addition, SDUP was largely affected by the acoustic impedance of the material being dried, showing a similar pattern with the impedance than the transmission coefficient of the acoustic energy on the interface. Thus, soft and open-porous product structures exhibited a better transmission of acoustic energy and were more prone to the mechanical effects of ultrasound. However, materials with a hard and closed-compact structure were less affected by acoustic energy due to the fact that the significant impedance differences between the product and the air cause high energy losses on the interface.

  11. Pyrolysis of polymeric materials. I - Effect of chemical structure, temperature, heating rate, and air flow on char yield and toxicity

    NASA Technical Reports Server (NTRS)

    Hilado, C. J.; Casey, C. J.

    1979-01-01

    Various polymeric materials, including synthetic polymers and cellulosic materials, were evaluated at different temperatures, heating rates and air flow rates for thermophysical and toxicological responses. It is shown that char yields appeared to be a function of air access as much as of the chemical structure of the material. It is stated that the sensitivity of the apparent thermal stability of some materials to air access is so marked that thermogravimetric studies in oxygen-free atmospheres may be a consistently misleading approach to comparing synthetic polymers intended to increase fire safety. Toxicity also appeared to be a function of temperature and air access as much as of the chemical structure of the material. Toxicity of the gases evolved seemed to increase with increasing char yield for some polymers.

  12. Thin tubular self-supporting electrode for solid oxide electrolyte electrochemical cells

    DOEpatents

    Carlson, W.G.; Ruka, R.J.

    1992-04-28

    A self-supporting, gas-permeable air electrode tube is made having a sintered structure of calcium-doped LaMnO[sub 3], a density of from 60% to 85% of theoretical density, and a Coefficient of Thermal Expansion of from 10.2 [times] 10[sup [minus]6]/C to 10.8 [times] 10[sup [minus]6]/C, where one end is open and the other end is sealed with a plug. 2 figs.

  13. Thin tubular self-supporting electrode for solid oxide electrolyte electrochemical cells

    DOEpatents

    Carlson, William G.; Ruka, Roswell J.

    1992-01-01

    A self-supporting, gas-permeable air electrode tube (16) is made having a sintered structure of calcium-doped LaMnO.sub.3, a density of from 60% to 85% of theoretical density, and a Coefficient of Thermal Expansion of from 10.2.times.10.sup.-6 /.degree.C. to 10.8.times.10.sup.-6 /.degree.C., where one end is open and the other end is sealed with a plug (30).

  14. Photoelectrochemical detection of alpha-fetoprotein based on ZnO inverse opals structure electrodes modified by Ag2S nanoparticles.

    PubMed

    Jiang, Yandong; Liu, Dali; Yang, Yudan; Xu, Ru; Zhang, Tianxiang; Sheng, Kuang; Song, Hongwei

    2016-12-06

    In this work, a new photoelectrochemical biosensor based on Ag2S nanoparticles (NPs) modified macroporous ZnO inverse opals structure (IOs) was developed for sensitive and rapid detection of alpha fetal protein (AFP). Small size and uniformly dispersed Ag2S NPs were prepared using the Successive Ionic Layer Adsorption And Reaction (SILAR) method, which were adsorbed on ZnO IOs surface and frame work as matrix for immobilization of AFP. The composite structure of ZnO/Ag2S expanded the scope of light absorption to long wavelength, which can make full use of the light energy. Meanwhile, an effective matching of energy levels between the conduction bands of Ag2S and ZnO are beneficial to the photo-generated electrons transfer. The biosensors based on FTO (fluorine-doped tinoxide) ZnO/Ag2S electrode showed enough sensitivity and a wide linear range from 0.05 ng/mL to 200 ng/mL with a low detection limit of 8 pg/mL for the detection of AFP. It also exhibited high reproducibility, specificity and stability. The proposed method was potentially attractive for achieving excellent photoelectrochemical biosensor for detection of other proteins.

  15. Photoelectrochemical detection of alpha-fetoprotein based on ZnO inverse opals structure electrodes modified by Ag2S nanoparticles

    PubMed Central

    Jiang, Yandong; Liu, Dali; Yang, Yudan; Xu, Ru; Zhang, Tianxiang; Sheng, Kuang; Song, Hongwei

    2016-01-01

    In this work, a new photoelectrochemical biosensor based on Ag2S nanoparticles (NPs) modified macroporous ZnO inverse opals structure (IOs) was developed for sensitive and rapid detection of alpha fetal protein (AFP). Small size and uniformly dispersed Ag2S NPs were prepared using the Successive Ionic Layer Adsorption And Reaction (SILAR) method, which were adsorbed on ZnO IOs surface and frame work as matrix for immobilization of AFP. The composite structure of ZnO/Ag2S expanded the scope of light absorption to long wavelength, which can make full use of the light energy. Meanwhile, an effective matching of energy levels between the conduction bands of Ag2S and ZnO are beneficial to the photo-generated electrons transfer. The biosensors based on FTO (fluorine-doped tinoxide) ZnO/Ag2S electrode showed enough sensitivity and a wide linear range from 0.05 ng/mL to 200 ng/mL with a low detection limit of 8 pg/mL for the detection of AFP. It also exhibited high reproducibility, specificity and stability. The proposed method was potentially attractive for achieving excellent photoelectrochemical biosensor for detection of other proteins. PMID:27922086

  16. Crystal structure and spin dynamics for the Li9V3P(8-δ)O(29-δ') insertion electrode system with a multiple-electron reaction.

    PubMed

    Onoda, Masashige; Ikeda, Satoshi; Ishibashi, Takehiko

    2012-02-29

    The crystal structure, the electron configurations of V ions and the spin dynamics for the Li(9)V(3)P(8-δ)O(29-δ') insertion electrode system that exhibits a multiple-electron reaction are explored through measurements of x-ray four-circle diffraction, magnetization and nuclear magnetic resonance. The structure for the stoichiometric composition with δ = δ' = 0 is refined precisely and the effective valences of all ions are determined. The electron configurations of V ions for the system annealed at various temperatures are considered in the framework of intermediate crystal field approach. For the system that often exhibits the charge-discharge performance better than the double-electron reaction, the spin dynamics mainly for the tetrahedral Li3 ions is understood on the basis of the relaxation mechanisms of quadrupole coupling and resonance shift anisotropy caused by the dipolar field of V ions. The correlation time of fluctuating fields is proportional to the temperature above 30 K, below which it follows the fractional Debye-Stokes-Einstein relation.

  17. Electrically conductive connection for an electrode

    DOEpatents

    Hornack, T.R.; Chilko, R.J.

    1986-09-02

    An electrically conductive connection for an electrode assembly of an electrolyte cell in which aluminum is produced by electrolysis in a molten salt is described. The electrode assembly comprises an electrode flask and a conductor rod. The flask has a collar above an area of minimum flask diameter. The electrically conductive connection comprises the electrode flask, the conductor rod and a structure bearing against the collar and the conductor rod for pulling the conductor rod into compressive and electrical contact with the flask. 2 figs.

  18. New electrosurgical ball electrode with nonstick properties

    NASA Astrophysics Data System (ADS)

    Rondinone, Joseph; Brassell, James; Miller, Scott A., III; Thorne, Jonathan O.; Rondinone, David M.; Safabash, Jason; Vega, Felix

    1998-04-01

    A new electrosurgical ball electrode (SilverBulletTM) has been developed for applying radiofrequency (RF) energy to fuse biological and other materials to tissue surfaces. Specifically, the electrode was developed for use in conjunction with the Fusion Medical Technologies, Inc. gelatin patch (RapiSealTM) for use in pulmonary surgery to seal air leaks, and in solid abdominal organ surgeries to provide hemostatic tamponade. The new electrode allows for the application of RF energy in contact mode without the problems of the electrode sticking to the gelatin patch or the underlying tissue. Designed for use with commercially available electrosurgical handpieces, the electrode consists of a stainless steel connector that fits into the hand- piece, and an electrode assembly made from silver that includes a shank region, and a tip extension extending distally from the shank region. The distal tip of the tip extension is rounded and has a length of about 10 mm. The uniqueness of this electrode is the shank region which has a cross sectional area that is larger than the tip extension. The shank region acts as a heat sink to draw away heat from the tip extension while the tip extension itself remains sufficiently small to access desired target sites and display the desired energy transfer properties. In addition to the physical design, the use of silver as the core element provides a material with high electrical and thermal conductivities. The bulk of the electrode is appropriately insulated.

  19. Advances in lightweight nickel electrode technology

    NASA Technical Reports Server (NTRS)

    Coates, Dwaine; Paul, Gary; Wheeler, James R.; Daugherty, Paul

    1989-01-01

    Studies are currently underway to further the development of lightweight nickel electrode technology. Work is focused primarily on the space nickel-hydrogen system and nickel-iron system but is also applicable to the nickel-cadmium and nickel-zinc systems. The goal is to reduce electrode weight while maintaining or improving performance thereby increasing electrode energy density. Two basic electrode structures are being investigated. The first is the traditional nickel sponge produced from sintered nickel-carbonyl powder and the second is a new material for this application which consists of a non-woven mat of nickel fiber. Electrodes are being manufactured, tested and evaluated at the electrode and cell level.

  20. Advances in lightweight nickel electrode technology

    NASA Technical Reports Server (NTRS)

    Coates, Dwaine; Paul, Gary; Daugherty, Paul

    1989-01-01

    Studies are currently underway to further the development of lightweight nickel electrode technology. Work is focused primarily on the space nickel-hydrogen system and nickel-iron system but is also applicable to the nickel-cadmium and nickel-zinc systems. The goal is to reduce electrode weight while maintaining or improving performance, thereby increasing electrode energy density. Two basic electrode structures are being investigated. The first is the traditional nickel sponge produced from sintered nickel-carbonyl powder. The second is a new material for this application which consists of a non-woven mat of nickel fiber. Electrodes are being manufactured, tested, and evaluated at the electrode and cell level.