A virtual model of the bench press exercise.

PubMed

Rahmani, Abderrahmane; Rambaud, Olivier; Bourdin, Muriel; Mariot, Jean-Pierre

2009-08-07

The objective of this study was to design and validate a three degrees of freedom model in the sagittal plane for the bench press exercise. The mechanical model was based on rigid segments connected by revolute and prismatic pairs, which enabled a kinematic approach and global force estimation. The method requires only three simple measurements: (i) horizontal position of the hand (x(0)); (ii) vertical displacement of the barbell (Z) and (iii) elbow angle (theta). Eight adult male throwers performed maximal concentric bench press exercises against different masses. The kinematic results showed that the vertical displacement of each segment and the global centre of mass followed the vertical displacement of the lifted mass. Consequently, the vertical velocity and acceleration of the combined centre of mass and the lifted mass were identical. Finally, for each lifted mass, there were no practical differences between forces calculated from the bench press model and those simultaneously measured with a force platform. The error was lower than 2.5%. The validity of the mechanical method was also highlighted by a standard error of the estimate (SEE) ranging from 2.0 to 6.6N in absolute terms, a coefficient of variation (CV) < or =0.8%, and a correlation between the two scores > or =0.99 for all the lifts (p<0.001). The method described here, which is based on three simple parameters, allows accurate evaluation of the force developed by the upper limb muscles during bench press exercises in both field and laboratory conditions.

NanoBench: An Individually Addressable Nanotube Array

DTIC Science & Technology

2006-03-25

17 (1999). 5 Cai, L., H. Tabata and T. Kawai, "Probing electrical properties of oriented DNA by conducting atomic force microscopy", Nanotechnology 12...the e-beam hits the other side of the NanoBench. This allows the cells to be kept alive in a biological medium while they are being tested. The key...advantage of the NanoBench is that the e-beam never hits the sample. UHV Technologies Inc. 7 NanoBench: An Individually Addressable Nanotube Array Final

Unknown loads affect force production capacity in early phases of bench press throws.

PubMed

Hernández Davó, J L; Sabido Solana, R; Sarabia Marínm, J M; Sánchez Martos, Á; Moya Ramón, M

2015-10-01

Explosive strength training aims to improve force generation in early phases of movement due to its importance in sport performance. The present study examined the influence of lack of knowledge about the load lifted in explosive parameters during bench press throws. Thirteen healthy young men (22.8±2.0 years) participated in the study. Participants performed bench press throws with three different loads (30, 50 and 70% of 1 repetition maximum) in two different conditions (known and unknown loads). In unknown condition, loads were changed within sets in each repetition and participants did not know the load, whereas in known condition the load did not change within sets and participants had knowledge about the load lifted. Results of repeated-measures ANOVA revealed that unknown conditions involves higher power in the first 30, 50, 100 and 150 ms with the three loads, higher values of ratio of force development in those first instants, and differences in time to reach maximal rate of force development with 50 and 70% of 1 repetition maximum. This study showed that unknown conditions elicit higher values of explosive parameters in early phases of bench press throws, thereby this kind of methodology could be considered in explosive strength training.

Muscular outputs during dynamic bench press under stable versus unstable conditions.

PubMed

Koshida, Sentaro; Urabe, Yukio; Miyashita, Koji; Iwai, Kanzunori; Kagimori, Aya

2008-09-01

Previous studies have suggested that resistance training exercise under unstable conditions decreases the isometric force output, yet little is known about its influence on muscular outputs during dynamic movement. The objective of this study was to investigate the effect of an unstable condition on power, force, and velocity outputs during the bench press. Twenty male collegiate athletes (mean age, 21.3 +/- 1.5 years; mean height, 167.7 +/- 7.7 cm; mean weight, 75.9 +/- 17.5 kg) participated in this study. Each subject attempted 3 sets of single bench presses with 50% of 1 repetition maximum (1RM) under a stable condition with a flat bench and an unstable condition with a Swiss ball. Acceleration data were obtained with an accelerometer attached to the center of a barbell shaft, and peak outputs of power, force, and velocity were computed. Although significant loss of the peak outputs was found under the unstable condition (p < 0.017), their reduction rates remained relatively low, approximately 6% for force and 10% for power and velocity outputs, compared with previous findings. Such small reduction rates of muscular outputs may not compromise the training effect. Prospective studies are necessary to confirm whether the resistance training under an unstable condition permits the improvement of dynamic performance and trunk stability.

Magnetic resonance elastography using an air ball-actuator.

PubMed

Numano, Tomokazu; Kawabata, Yoshihiko; Mizuhara, Kazuyuki; Washio, Toshikatsu; Nitta, Naotaka; Homma, Kazuhiro

2013-07-01

The purpose of this study was to develop a new technique for a powerful compact MR elastography (MRE) actuator based on a pneumatic ball-vibrator. This is a compact actuator that generates powerful centrifugal force vibrations via high speed revolutions of an internal ball using compressed air. This equipment is easy to handle due to its simple principles and structure. Vibration frequency and centrifugal force are freely adjustable via air pressure changes (air flow volume), and replacement of the internal ball. In order to achieve MRI compatibility, all parts were constructed from non-ferromagnetic materials. Vibration amplitudes (displacements) were measured optically by a laser displacement sensor. From a bench test of displacement, even though the vibration frequency increased, the amount of displacement did not decrease. An essential step in MRE is the generation of mechanical waves within tissue via an actuator, and MRE sequences are synchronized to several phase offsets of vibration. In this system, the phase offset was detected by a four-channel optical-fiber sensor, and it was used as an MRI trigger signal. In an agarose gel phantom experiment, this actuator was used to make an MR elastogram. This study shows that the use of a ball actuator for MRE is feasible. Copyright © 2013 Elsevier Inc. All rights reserved.

A Comparison between Bench Press Throw and Ballistic Push-Up tests to assess upper-body power in trained individuals.

PubMed

Bartolomei, Sandro; Nigro, Federico; Ruggeri, Sandro; Lanzoni, Ivan Malagoli; Ciacci, Simone; Merni, Franco; Sadres, Eliahu; Hoffman, Jay R; Semprini, Gabriele

2018-03-06

The purpose of the present study was to validate the ballistic push-up test performed with hands on a force plate (BPU) as a method to measure upper-body power. Twenty-eight experienced resistance trained men (age = 25.4 ± 5.2 y; body mass = 78.5 ± 9.0 kg; body height = 179.6 ± 7.8 cm) performed, two days apart, a bench press 1RM test and upper-body power tests. Mean power and peak power were assessed using the bench press throw test (BT) and the BPU test performed in randomized order. The area under the force/power curve (AUC) obtained at BT was also calculated. Power expressed at BPU was estimated using a time-based prediction equation. Mean force and the participant's body weight were used to predict the bench press 1RM. Pearson product moment correlations were used to examine relationships between the power assessment methods and between the predicted 1RM bench and the actual value. Large correlations (0.79; p < 0.001) were found between AUC and mean power expressed at BPU. Large correlations were also detected between mean power and peak power expressed at BT and BPU (0.75; p < 0.001 and 0.74; p < 0.001, respectively). Very large correlations (0.87; p < 0.001) were found between the 1RM bench and the 1RM predicted by the BPU. Results of the present study indicate that BPU represents a valid and reliable method to estimate the upper-body power in resistance-trained individuals.

The influence of variable range of motion training on neuromuscular performance and control of external loads.

PubMed

Clark, Ross A; Humphries, Brendan; Hohmann, Erik; Bryant, Adam L

2011-03-01

Resistance training programs that emphasize high force production in different regions of the range of motion (ROM) may provide performance benefits. This study examined whether variable ROM (VROM) training, which consists of partial ROM training with countermovements performed in a different phase of the ROM for each set, results in improved functional performance. Twenty-two athletes (age 22.7 ± 2.4 years, height 1.81 ± 0.07 m, and body mass 94.6 ± 14.5 kg) with extensive resistance training backgrounds performed either a VROM or full ROM control (CON) 5-week, concentric work-matched training program. The participants were assigned to a group based on stratified randomization incorporating their strength levels and performance gains in preceding training microcycles. Testing consisted of assessing the force-ROM relationship during isokinetic and isometric bench press and ballistic bench throws, with normalized electromyography amplitude assessed during the isometric tests. Repeated-measure analyses of variance revealed that the VROM intervention significantly (p < 0.05) increased both full ROM bench throw displacement (+15.5%) and half ROM bench throw peak force (+15.7%), in addition to isokinetic peak force in the terminal ROM (13.5% increase). No significant differences were observed in the CON group or between groups for any other outcome measures. Analysis of the force-ROM relationship revealed that that the VROM intervention enhanced performance at shorter muscle lengths. These findings suggest that VROM training improves terminal and midrange performance gains, resulting in the athlete possessing an improved ability to control external loading and produce dynamic force.

A comparison of muscle activity in concentric and counter movement maximum bench press.

PubMed

van den Tillaar, Roland; Ettema, Gertjan

2013-01-01

The purpose of this study was to compare the kinematics and muscle activation patterns of regular free-weight bench press (counter movement) with pure concentric lifts in the ascending phase of a successful one repetition maximum (1-RM) attempt in the bench press. Our aim was to evaluate if diminishing potentiation could be the cause of the sticking region. Since diminishing potentiation cannot occur in pure concentric lifts, the occurrence of a sticking region in this type of muscle actions would support the hypothesis that the sticking region is due to a poor mechanical position. Eleven male participants (age 21.9 ± 1.7 yrs, body mass 80.7 ± 10.9 kg, body height 1.79 ± 0.07 m) conducted 1-RM lifts in counter movement and in pure concentric bench presses in which kinematics and EMG activity were measured. In both conditions, a sticking region occurred. However, the start of the sticking region was different between the two bench presses. In addition, in four of six muscles, the muscle activity was higher in the counter movement bench press compared to the concentric one. Considering the findings of the muscle activity of six muscles during the maximal lifts it was concluded that the diminishing effect of force potentiation, which occurs in the counter movement bench press, in combination with a delayed muscle activation unlikely explains the existence of the sticking region in a 1-RM bench press. Most likely, the sticking region is the result of a poor mechanical force position.

A Comparison of Muscle Activity in Concentric and Counter Movement Maximum Bench Press

PubMed Central

van den Tillaar, Roland; Ettema, Gertjan

2013-01-01

The purpose of this study was to compare the kinematics and muscle activation patterns of regular free-weight bench press (counter movement) with pure concentric lifts in the ascending phase of a successful one repetition maximum (1-RM) attempt in the bench press. Our aim was to evaluate if diminishing potentiation could be the cause of the sticking region. Since diminishing potentiation cannot occur in pure concentric lifts, the occurrence of a sticking region in this type of muscle actions would support the hypothesis that the sticking region is due to a poor mechanical position. Eleven male participants (age 21.9 ± 1.7 yrs, body mass 80.7 ± 10.9 kg, body height 1.79 ± 0.07 m) conducted 1-RM lifts in counter movement and in pure concentric bench presses in which kinematics and EMG activity were measured. In both conditions, a sticking region occurred. However, the start of the sticking region was different between the two bench presses. In addition, in four of six muscles, the muscle activity was higher in the counter movement bench press compared to the concentric one. Considering the findings of the muscle activity of six muscles during the maximal lifts it was concluded that the diminishing effect of force potentiation, which occurs in the counter movement bench press, in combination with a delayed muscle activation unlikely explains the existence of the sticking region in a 1-RM bench press. Most likely, the sticking region is the result of a poor mechanical force position. PMID:24235985

Comparative tests of bench equipment for fuel control system testing of gas-turbine engine

NASA Astrophysics Data System (ADS)

Shendaleva, E. V.

2018-04-01

The relevance of interlaboratory comparative researches is confirmed by attention of world metrological community to this field of activity. Use of the interlaboratory comparative research methodology not only for single gages collation, but also for bench equipment complexes, such as modeling stands for fuel control system testing of gas-turbine engine, is offered. In this case a comparative measure of different bench equipment will be the control fuel pump. Ensuring traceability of measuring result received at test benches of various air enterprises, development and introduction of national standards to practice of bench tests and, eventually, improvement of quality and safety of a aircraft equipment is result of this approach.

Shoulder joint abduction motion test bench: a new shoulder test bench for in vitro experiments with active muscle force simulation.

PubMed

Onder, Ursula; Blauth, Michael; Kralinger, Franz; Schmoelz, Werner

2012-05-30

In our society the average age is increasing, as are the number of proximal humeral head fractures. For fixation of these fractures, an increasing number of implants are available. New fixation devices should be compared biomechanically with established methods in a standardized fashion. The test bench that was designed was intended to simulate abduction motion of the humerus actively induced by muscle forces. We used three pneumatic muscles to apply forces to the tendons of the musculus supraspinatus and the bifid musculus deltoideus. Thus, it was possible to create an active abduction in the scapular plane. Two different fracture models (with and without medial support) were stabilised with an angular stable plate in sawbone models to reproduce a known clinical outcome with the newly designed test setup. The resultant force acting on the proximal humerus reached approximately 47% BW (per cent body weight), which amounted to 329.0 N (SD: 21.76). The supraspinatus reached maximum forces of 254.7 N (SD: 20.1) and the deltoid muscle 258.9 N (SD: 16.5). Fracture gap instrumentation with medial support resulted in a significantly reduced per-cycle fracture gap motion. The performance evaluation showed that the simulator produced predicable, reproducible movements with physiological muscle force magnitudes.

Associations Between Rate of Force Development Metrics and Throwing Velocity in Elite Team Handball Players: a Short Research Report

PubMed Central

Marques, Mário C.; Saavedra, Francisco J.; Abrantes, Catarina; Aidar, Felipe J.

2011-01-01

Performance assessment has become an invaluable component of monitoring participant’s development in distinct sports, yet limited and contradictory data are available in trained subjects. The purpose of this study was to examine the relationship between ball throwing velocity during a 3-step running throw in elite team handball players and selected measures of rate of force development like force, power, velocity, and bar displacement during a concentric only bench press exercise in elite male handball players. Fitteen elite senior male team handball players volunteered to participate. Each volunteer had power and bar velocity measured during a concentric only bench press test with 25, 35, and 45 kg as well as having one-repetition maximum strength determined. Ball throwing velocity was evaluated with a standard 3-step running throw using a radar gun. The results of this study indicated significant associations between ball velocity and time at maximum rate of force development (0, 66; p<0.05) and rate of force development at peak force (0,56; p<0.05) only with 25kg load. The current research indicated that ball velocity was only median associated with maximum rate of force development with light loads. A training regimen designed to improve ball-throwing velocity in elite male team handball players should emphasize bench press movement using light loads. PMID:23487363

Associations between rate of force development metrics and throwing velocity in elite team handball players: a short research report.

PubMed

Marques, Mário C; Saavedra, Francisco J; Abrantes, Catarina; Aidar, Felipe J

2011-09-01

Performance assessment has become an invaluable component of monitoring participant's development in distinct sports, yet limited and contradictory data are available in trained subjects. The purpose of this study was to examine the relationship between ball throwing velocity during a 3-step running throw in elite team handball players and selected measures of rate of force development like force, power, velocity, and bar displacement during a concentric only bench press exercise in elite male handball players. Fitteen elite senior male team handball players volunteered to participate. Each volunteer had power and bar velocity measured during a concentric only bench press test with 25, 35, and 45 kg as well as having one-repetition maximum strength determined. Ball throwing velocity was evaluated with a standard 3-step running throw using a radar gun. The results of this study indicated significant associations between ball velocity and time at maximum rate of force development (0, 66; p<0.05) and rate of force development at peak force (0,56; p<0.05) only with 25kg load. The current research indicated that ball velocity was only median associated with maximum rate of force development with light loads. A training regimen designed to improve ball-throwing velocity in elite male team handball players should emphasize bench press movement using light loads.

Elbow joint fatigue and bench-press training.

PubMed

Huang, Yen-Po; Chou, You-Li; Chen, Feng-Chun; Wang, Rong-Tyai; Huang, Ming-Jer; Chou, Paul Pei-Hsi

2014-01-01

Bench-press exercises are among the most common form of training exercise for the upper extremity because they yield a notable improvement in both muscle strength and muscle endurance. The literature contains various investigations into the effects of different bench-press positions on the degree of muscle activation. However, the effects of fatigue on the muscular performance and kinetics of the elbow joint are not understood fully. To investigate the effects of fatigue on the kinetics and myodynamic performance of the elbow joint in bench-press training. Controlled laboratory study. Motion research laboratory. A total of 18 physically healthy male students (age = 19.6 ± 0.8 years, height = 168.7 ± 5.5 cm, mass = 69.6 ± 8.6 kg) participated in the investigation. All participants were right-hand dominant, and none had a history of upper extremity injuries or disorders. Participants performed bench-press training until fatigued. Maximal possible number of repetitions, cycle time, myodynamic decline rate, elbow-joint force, and elbow-joint moment. We observed a difference in cycle time in the initial (2.1 ± 0.42 seconds) and fatigue (2.58 ± 0.46 seconds) stages of the bench-press exercise (P = .04). As the participants fatigued, we observed an increase in the medial-lateral force (P = .03) and internal-external moment (P ≤ .04) acting on the elbow joint. Moreover, a reduction in the elbow muscle strength was observed in the elbow extension-flexion (P ≤ .003) and forearm supination-pronation (P ≤ .001) conditions. The results suggest that performing bench-press exercises to the point of fatigue increases elbow-joint loading and may further increase the risk of injury. Therefore, when clinicians design bench-press exercise regimens for general athletic training, muscle strengthening, or physical rehabilitation, they should control carefully the maximal number of repetitions.

Comparison of muscle force production using the Smith machine and free weights for bench press and squat exercises.

PubMed

Cotterman, Michael L; Darby, Lynn A; Skelly, William A

2005-02-01

The Smith machine (SM) (vertical motion of bar on fixed path; fixed-form exercise) and free weights (FWs) (free-form path) are commonly used strength training modes. Exercisers may need to alternate between types of equipment, depending on testing, training, rehabilitation, and/or the exercisers' goals. The purposes of this study were to compare muscle force production for SM and FWs using a 1 repetition maximum (1RM) for the parallel back squat and supine bench press exercises and to predict the 1RM for one mode from 1RM on the other mode. Men (n = 16) and women (n = 16) alternately completed 1RM testing for squat and bench press using SM and FWs. Analyses of variance (type of equipment x sex) and linear regression models were calculated. A significant difference was found between bench press and squat 1RMs for each mode of equipment for all participants. The squat 1RM was greater for the SM than the FWs; conversely, the bench 1RM was greater for FWs than the SM. When sex was considered, bench 1RM for FWs was greater than SM for men and women. The squat 1RM was greater for SM than FWs for women only. The 1RM on one mode of equipment was the best predictor of 1RM for the other mode. For both sexes, the equation SM bench 1RM (in kilograms) = -6.76 + 0.95 (FW bench 1RM) can be used. For women only, SM squat 1RM (in kilograms) = 28.3 + 0.73 (FW squat 1RM). These findings provide equations for converting between SM and FW equipment for training.

Ceramic membrane defouling (cleaning) by air Nano Bubbles.

PubMed

Ghadimkhani, Aliasghar; Zhang, Wen; Marhaba, Taha

2016-03-01

Ceramic membranes are among the most promising technologies for membrane applications, owing to their excellent resistance to mechanical, chemical, and thermal stresses. However, membrane fouling is still an issue that hampers the applications at large scales. Air Nano Bubbles (NBs), due to high mass transfer efficiency, could potentially prevent fouling of ceramic membrane filtration processes. In this study, bench and pilot scale ceramic membrane filtration was performed with air NBs to resist fouling. To simulate fouling, humic acid, as an organic foulant, was applied to the membrane flat sheet surface. Complete membrane clogging was achieved in less than 6 h. Membrane defouling (cleaning) was performed by directly feeding of air NBs to the membrane cells. The surface of the ceramic membrane was superbly cleaned by air NBs, as revealed by atomic force microscope (AFM) images before and after the treatment. The permeate flux recovered to its initial level (e.g., 26.7 × 10(-9) m(3)/m(2)/s at applied pressure of 275.8 kPa), which indicated that NBs successfully unclogged the pores of the membrane. The integrated ceramic membrane and air NBs system holds potential as an innovative sustainable technology. Copyright © 2015 Elsevier Ltd. All rights reserved.

Performance study of protective clothing against hot water splashes: from bench scale test to instrumented manikin test.

PubMed

Lu, Yehu; Song, Guowen; Wang, Faming

2015-03-01

Hot liquid hazards existing in work environments are shown to be a considerable risk for industrial workers. In this study, the predicted protection from fabric was assessed by a modified hot liquid splash tester. In these tests, conditions with and without an air spacer were applied. The protective performance of a garment exposed to hot water spray was investigated by a spray manikin evaluation system. Three-dimensional body scanning technique was used to characterize the air gap size between the protective clothing and the manikin skin. The relationship between bench scale test and manikin test was discussed and the regression model was established to predict the overall percentage of skin burn while wearing protective clothing. The results demonstrated strong correlations between bench scale test and manikin test. Based on these studies, the overall performance of protective clothing against hot water spray can be estimated on the basis of the results of the bench scale hot water splashes test and the information of air gap size entrapped in clothing. The findings provide effective guides for the design and material selection while developing high performance protective clothing. Published by Oxford University Press on behalf of the British Occupational Hygiene Society 2014.

Calculation of force and power during bench throws using a Smith machine: the importance of considering the effect of counterweights.

PubMed

Kobayashi, Y; Narazaki, K; Akagi, R; Nakagaki, K; Kawamori, N; Ohta, K

2013-09-01

For achieving accurate and safe measurements of the force and power exerted on a load during resistance exercise, the Smith machine has been used instead of free weights. However, because some Smith machines possess counterweights, the equation for the calculation of force and power in this system should be different from the one used for free weights. The purpose of this investigation was to calculate force and power using an equation derived from a dynamic equation for a Smith machine with counterweights and to determine the differences in force and power calculated using 2 different equations. One equation was established ignoring the effect of the counterweights (Method 1). The other equation was derived from a dynamic equation for a barbell and counterweight system (Method 2). 9 female collegiate judo athletes performed bench throws using a Smith machine with a counterweight at 6 different loading conditions. Barbell displacement was recorded using a linear position transducer. The force and power were subsequently calculated by Methods 1 and 2. The results showed that the mean and peak power and force in Method 1 were significantly lower relative to those of Method 2 under all loading conditions. These results indicate that the mean and peak power and force during bench throwing using a Smith machine with counterweights would be underestimated when the calculations used to determine these parameters do not account for the effect of counterweights. © Georg Thieme Verlag KG Stuttgart · New York.

Kinematics and kinetics of the bench-press and bench-pull exercises in a strength-trained sporting population.

PubMed

Pearson, Simon N; Cronin, John B; Hume, Patria A; Slyfield, David

2009-09-01

Understanding how loading affects power production in resistance training is a key step in identifying the most optimal way of training muscular power - an essential trait in most sporting movements. Twelve elite male sailors with extensive strength-training experience participated in a comparison of kinematics and kinetics from the upper body musculature, with upper body push (bench press) and pull (bench pull) movements performed across loads of 10-100% of one repetition maximum (1RM). 1RM strength and force were shown to be greater in the bench press, while velocity and power outputs were greater for the bench pull across the range of loads. While power output was at a similar level for the two movements at a low load (10% 1RM), significantly greater power outputs were observed for the bench pull in comparison to the bench press with increased load. Power output (Pmax) was maximized at higher relative loads for both mean and peak power in the bench pull (78.6 +/- 5.7% and 70.4 +/- 5.4% of 1RM) compared to the bench press (53.3 +/- 1.7% and 49.7 +/- 4.4% of 1RM). Findings can most likely be attributed to differences in muscle architecture, which may have training implications for these muscles.

Use of a Terrestrial LIDAR Sensor for Drift Detection in Vineyard Spraying

PubMed Central

Gil, Emilio; Llorens, Jordi; Llop, Jordi; Fàbregas, Xavier; Gallart, Montserrat

2013-01-01

The use of a scanning Light Detection and Ranging (LIDAR) system to characterize drift during pesticide application is described. The LIDAR system is compared with an ad hoc test bench used to quantify the amount of spray liquid moving beyond the canopy. Two sprayers were used during the field test; a conventional mist blower at two air flow rates (27,507 and 34,959 m3·h−1) equipped with two different nozzle types (conventional and air injection) and a multi row sprayer with individually oriented air outlets. A simple model based on a linear function was used to predict spray deposit using LIDAR measurements and to compare with the deposits measured over the test bench. Results showed differences in the effectiveness of the LIDAR sensor depending on the sprayed droplet size (nozzle type) and air intensity. For conventional mist blower and low air flow rate; the sensor detects a greater number of drift drops obtaining a better correlation (r = 0.91; p < 0.01) than for the case of coarse droplets or high air flow rate. In the case of the multi row sprayer; drift deposition in the test bench was very poor. In general; the use of the LIDAR sensor presents an interesting and easy technique to establish the potential drift of a specific spray situation as an adequate alternative for the evaluation of drift potential. PMID:23282583

Elbow Joint Fatigue and Bench-Press Training

PubMed Central

Huang, Yen-Po; Chou, You-Li; Chen, Feng-Chun; Wang, Rong-Tyai; Huang, Ming-Jer; Chou, Paul Pei-Hsi

2014-01-01

Context: Bench-press exercises are among the most common form of training exercise for the upper extremity because they yield a notable improvement in both muscle strength and muscle endurance. The literature contains various investigations into the effects of different bench-press positions on the degree of muscle activation. However, the effects of fatigue on the muscular performance and kinetics of the elbow joint are not understood fully. Objective: To investigate the effects of fatigue on the kinetics and myodynamic performance of the elbow joint in bench-press training. Design: Controlled laboratory study. Setting: Motion research laboratory. Patients or Other Participants: A total of 18 physically healthy male students (age = 19.6 ± 0.8 years, height = 168.7 ± 5.5 cm, mass = 69.6 ± 8.6 kg) participated in the investigation. All participants were right-hand dominant, and none had a history of upper extremity injuries or disorders. Intervention(s): Participants performed bench-press training until fatigued. Main Outcome Measure(s): Maximal possible number of repetitions, cycle time, myodynamic decline rate, elbow-joint force, and elbow-joint moment. Results: We observed a difference in cycle time in the initial (2.1 ± 0.42 seconds) and fatigue (2.58 ± 0.46 seconds) stages of the bench-press exercise (P = .04). As the participants fatigued, we observed an increase in the medial-lateral force (P = .03) and internal-external moment (P ≤ .04) acting on the elbow joint. Moreover, a reduction in the elbow muscle strength was observed in the elbow extension-flexion (P ≤ .003) and forearm supination-pronation (P ≤ .001) conditions. Conclusions: The results suggest that performing bench-press exercises to the point of fatigue increases elbow-joint loading and may further increase the risk of injury. Therefore, when clinicians design bench-press exercise regimens for general athletic training, muscle strengthening, or physical rehabilitation, they should control carefully the maximal number of repetitions. PMID:24533529

Effect of Heavy Dynamic Resistive Exercise on Acute Upper-Body Power.

ERIC Educational Resources Information Center

Hrysomallis, Con; Kidgell, Dawson

2001-01-01

Determined the influence of a heavy-load bench press on indicators of upper-body power during an explosive pushup, examining the influence of a set of 5 repetitions of 5 repetition maximum (RM) bench press preceding explosive pushups. There were no significant differences for any of the force platform data when explosive pushups were preceded by…

Environmental Fate and Transport of Poly- and Perfluoroalkyl Substances at Aqueous Film-Forming Foam Impacted Sites

NASA Astrophysics Data System (ADS)

Higgins, C.

2017-12-01

Poly and perfluoroalkyl substances (PFASs) are constituents in aqueous film-forming foam (AFFF) used to extinguish fuel fires. Substantially elevated PFAS groundwater concentrations have been observed at firefighter protection training areas, where co-contaminants such as chlorinated solvents and fuel hydrocarbons are also commonly present. Research into the fate and transport potential of PFASs at AFFF-impacted sites will be presented, with a particular focus on how co-contaminants and co-contaminant remediation technologies may alter the composition and transport behavior of PFASs at these sites. A detailed analysis of data collected from a U.S. Air Force site (Ellsworth Air Force Base, South Dakota) indicates that that conversion of polyfluoroalkyl chemicals to perfluoroalkyl acids (PFAAs) in situ due to natural and enhanced remediation of petroleum hydrocarbons. In addition, bench-scale studies examining the effects of various chemical oxidants, typically employed via in situ chemical oxidation (ISCO), indicates that oxidation-based remediation technologies have the potential to alter the release and composition of PFASs in AFFF-impacted source zones. Future challenges in addressing PFAS contamination will be discussed, particularly with respect to closing the mass balance on PFAAs and their precursors at AFFF-impacted sites.

Active vibration control on a quarter-car for cancellation of road noise disturbance

NASA Astrophysics Data System (ADS)

Belgacem, Walid; Berry, Alain; Masson, Patrice

2012-07-01

In this paper, a methodology is presented for the cancellation of road noise, from the analysis of vibration transmission paths for an automotive suspension to the design of an active control system using inertial actuators on a suspension to reduce the vibrations transmitted to the chassis. First, experiments were conducted on a Chevrolet Epica LS automobile on a concrete test track to measure accelerations induced on the suspension by the road. These measurements were combined with experimental Frequency Response Functions (FRFs) measured on a quarter-car test bench to reconstruct an equivalent three dimensional force applied on the wheel hub. Second, FRFs measured on the test bench between the three-dimensional driving force and forces at each suspension/chassis linkage were used to characterize the different transmission paths of vibration energy to the chassis. Third, an experimental model of the suspension was constructed to simulate the configuration of the active control system, using the primary (disturbance) FRFs and secondary (control) FRFs also measured on the test bench. This model was used to optimize the configuration of the control actuators and to evaluate the required forces. Finally, a prototype of an active suspension was implemented and measurements were performed in order to assess the performance of the control approach. A 4.6 dB attenuation on transmitted forces was obtained in the 50-250 Hz range.

Village Green Project Fact Sheet

EPA Pesticide Factsheets

EPA has developed an innovative, solar-powered air-monitoring system designed and incorporated into a park bench. The Village Green Project is being conducted in partnership with Durham County to advance air quality measurement capabilities.

A simple and inexpensive method for maintaining a defined flora mouse colony.

PubMed

Sedlacek, R S; Mason, K A

1977-10-01

The use of autoclaved cages, feed, bedding, water, and filter caps combined with aseptic techniques of animal husbandry in an existing mouse colony was ineffective in maintaining a defined flora colony. The addition of a laminar air flow bench equipped with a high efficiency particulate air filter provided a sterile environment in which to manipulate mice when the filter caps were removed. The installation of a duct to direct all air entering the room through the bench filter reduced the airborne bacterial counts in the room. This modification combined with the culling or marking of infected cages so that no future breeders would be taken from these cages eliminated a number of bacterial contaminants (Staphylococcus aureus, S epidermidis, and streptococci) from the colony.

Tools for experimental characterization of the non-uniform rotational distortion in intravascular OCT probes

NASA Astrophysics Data System (ADS)

Dufour, Marc L.; Bisaillon, Charles-Etienne; Lamouche, Guy; Vergnole, Sebastien; Hewko, Mark; D'Amours, Frédéric; Padioleau, Christian; Sowa, Michael

2011-03-01

The Industrial Material Institute (IMI) together with the Institute for Biodiagnostic (IBD) has developed its own optical catheters for cardiovascular imaging applications. Those catheters have been used experimentally in the in vitro coronary artery model of the Langendorff beating heart and in a percutaneous coronary intervention procedure in a porcine model. For some catheter designs, non-uniform rotational distortion (NURD) can be observed as expected from past experience with intra-vascular ultrasound (IVUS) catheters. A two-dimensional (2D) coronary artery test bench that simulates the path into the coronary arteries has been developed. The presence or absence of NURD can be assessed with the test bench using a custom-built cardiovascular Optical Coherence Tomography (OCT) imaging system. A square geometry instead of the circular shape of an artery is used to simulate the coronary arteries. Thereby, it is easier to visualize NURD when it is present. The accumulated torsion induced by the friction on the catheter is measured along the artery path. NURD is induced by the varying friction force that is balanced by the accumulated torsion force. The pullback force is measured and correlated with NURD observed in the 2D test bench. Finally, a model is presented to help understanding the mechanical constraint that leads to the friction force variations.

Using Maximal Isometric Force to Determine the Optimal Load for Measuring Dynamic Muscle Power

NASA Technical Reports Server (NTRS)

Spiering, Barry A.; Lee, Stuart M. C.; Mulavara, Ajitkumar P.; Bentley, Jason R.; Nash, Roxanne E.; Sinka, Joseph; Bloomberg, Jacob J.

2009-01-01

Maximal power output occurs when subjects perform ballistic exercises using loads of 30-50% of one-repetition maximum (1-RM). However, performing 1-RM testing prior to power measurement requires considerable time, especially when testing involves multiple exercises. Maximal isometric force (MIF), which requires substantially less time to measure than 1-RM, might be an acceptable alternative for determining the optimal load for power testing. PURPOSE: To determine the optimal load based on MIF for maximizing dynamic power output during leg press and bench press exercises. METHODS: Twenty healthy volunteers (12 men and 8 women; mean +/- SD age: 31+/-6 y; body mass: 72 +/- 15 kg) performed isometric leg press and bench press movements, during which MIF was measured using force plates. Subsequently, subjects performed ballistic leg press and bench press exercises using loads corresponding to 20%, 30%, 40%, 50%, and 60% of MIF presented in randomized order. Maximal instantaneous power was calculated during the ballistic exercise tests using force plates and position transducers. Repeated-measures ANOVA and Fisher LSD post hoc tests were used to determine the load(s) that elicited maximal power output. RESULTS: For the leg press power test, six subjects were unable to be tested at 20% and 30% MIF because these loads were less than the lightest possible load (i.e., the weight of the unloaded leg press sled assembly [31.4 kg]). For the bench press power test, five subjects were unable to be tested at 20% MIF because these loads were less than the weight of the unloaded aluminum bar (i.e., 11.4 kg). Therefore, these loads were excluded from analysis. A trend (p = 0.07) for a main effect of load existed for the leg press exercise, indicating that the 40% MIF load tended to elicit greater power output than the 60% MIF load (effect size = 0.38). A significant (p . 0.05) main effect of load existed for the bench press exercise; post hoc analysis indicated that the effect of load on power output was: 30% > 40% > 50% = 60%. CONCLUSION: Loads of 40% and 30% of MIF elicit maximal power output during dynamic leg presses and bench presses, respectively. These findings are similar to those obtained when loading is based on 1-RM.

Relationships between Mechanical Variables in the Traditional and Close-Grip Bench Press.

PubMed

Lockie, Robert G; Callaghan, Samuel J; Moreno, Matthew R; Risso, Fabrice G; Liu, Tricia M; Stage, Alyssa A; Birmingham-Babauta, Samantha A; Stokes, John J; Giuliano, Dominic V; Lazar, Adrina; Davis, DeShaun L; Orjalo, Ashley J

2017-12-01

The study aim was to determine relationships between mechanical variables in the one-repetition maximum (1RM) traditional bench press (TBP) and close-grip bench press (CGBP). Twenty resistance-trained men completed a TBP and CGBP 1RM. The TBP was performed with the preferred grip; the CGBP with a grip width of 95% biacromial distance. A linear position transducer measured: lift distance and duration; work; and peak and mean power, velocity, and force. Paired samples t-tests (p < 0.05) compared the 1RM and mechanical variables for the TBP and CGBP; effect sizes (d) were also calculated. Pearson's correlations (r; p < 0.05) computed relationships between the TBP and CGBP. 1RM, lift duration, and mean force were greater in the TBP (d = 0.30-3.20). Peak power and velocity was greater for the CGBP (d = 0.50-1.29). The 1RM TBP correlated with CGBP 1RM, power, and force (r = 0.685-0.982). TBP work correlated with CGBP 1RM, lift distance, power, force, and work (r = 0.542-0.931). TBP power correlated with CGBP 1RM, power, force, velocity, and work (r = 0.484-0.704). TBP peak and mean force related to CGBP 1RM, power, and force (r = 0.596-0.980). Due to relationships between the load, work, power, and force for the TBP and CGBP, the CGBP could provide similar strength adaptations to the TBP with long-term use. The velocity profile for the CGBP was different to that of the TBP. The CGBP could be used specifically to improve high-velocity, upper-body pushing movements.

Relationships between Mechanical Variables in the Traditional and Close-Grip Bench Press

PubMed Central

Callaghan, Samuel J.; Moreno, Matthew R.; Risso, Fabrice G.; Liu, Tricia M.; Stage, Alyssa A.; Birmingham-Babauta, Samantha A.; Stokes, John J.; Giuliano, Dominic V.; Lazar, Adrina; Davis, DeShaun L.; Orjalo, Ashley J.

2017-01-01

Abstract The study aim was to determine relationships between mechanical variables in the one-repetition maximum (1RM) traditional bench press (TBP) and close-grip bench press (CGBP). Twenty resistance-trained men completed a TBP and CGBP 1RM. The TBP was performed with the preferred grip; the CGBP with a grip width of 95% biacromial distance. A linear position transducer measured: lift distance and duration; work; and peak and mean power, velocity, and force. Paired samples t-tests (p < 0.05) compared the 1RM and mechanical variables for the TBP and CGBP; effect sizes (d) were also calculated. Pearson’s correlations (r; p < 0.05) computed relationships between the TBP and CGBP. 1RM, lift duration, and mean force were greater in the TBP (d = 0.30-3.20). Peak power and velocity was greater for the CGBP (d = 0.50-1.29). The 1RM TBP correlated with CGBP 1RM, power, and force (r = 0.685-0.982). TBP work correlated with CGBP 1RM, lift distance, power, force, and work (r = 0.542-0.931). TBP power correlated with CGBP 1RM, power, force, velocity, and work (r = 0.484-0.704). TBP peak and mean force related to CGBP 1RM, power, and force (r = 0.596-0.980). Due to relationships between the load, work, power, and force for the TBP and CGBP, the CGBP could provide similar strength adaptations to the TBP with long-term use. The velocity profile for the CGBP was different to that of the TBP. The CGBP could be used specifically to improve high-velocity, upper-body pushing movements. PMID:29339982

Theoretical Analysis and Bench Tests of a Control-Surface Booster Employing a Variable Displacement Hydraulic Pump

NASA Technical Reports Server (NTRS)

Mathews, Charles W.; Kleckner, Harold F.

1947-01-01

The NACA is conducting a general investigation of servo-mechanisms for use in powering aircraft control surfaces. This paper presents a theoretical analysis and the results of bench tests of a control-booster system which employs a variable displacement hydraulic pump. The booster is intended for use in a flight investigation to determine the effects of various booster parameters on the handling qualities of airplanes. Such a flight investigation would aid in formulating specific requirements concerning the design of control boosters in general. Results of the theoretical analysis and the bench tests indicate that the subject booster is representative of types which show promise of satisfactory performance. The bench tests showed that the following desirable features were inherent in this booster system: (1) No lost motion or play in any part of the system; (2) no detectable lag between motion of the contra1 stick and control surface; and (3) Good agreement between control displacements and stick-force variations with no hysteresis in the stick-force characteristics. The final design configuration of this booster system showed no tendency to oscillate, overshoot, or have other undesirable transient characteristics common to boosters.

A Simple Method for Assessing Upper-Limb Force-Velocity Profile in Bench Press.

PubMed

Rahmani, Abderrahmane; Samozino, Pierre; Morin, Jean-Benoit; Morel, Baptiste

2018-02-01

To analyze the reliability and validity of a field computation method based on easy-to-measure data to assess the mean force ([Formula: see text]) and velocity ([Formula: see text]) produced during a ballistic bench-press movement and to verify that the force-velocity profile (F-v) obtained with multiple loaded trials is accurately described. Twelve participants performed ballistic bench presses against various lifted mass from 30% to 70% of their body mass. For each trial, [Formula: see text] and [Formula: see text] were determined from an accelerometer (sampling rate 500 Hz; reference method) and a simple computation method based on upper-limb mass, barbell flight height, and push-off distance. These [Formula: see text] and [Formula: see text] data were used to establish the F-v relationship for each individual and method. A strong to almost perfect reliability was observed between the 2 trials (ICC > .90 for [Formula: see text] and .80 for [Formula: see text], CV% < 10%), whatever the considered method. The mechanical variables ([Formula: see text], [Formula: see text]) measured with the 2 methods and all the variables extrapolated from the F-v relationships were strongly correlated (r 2  > .80, P < .001). The practical differences between the methods for the extrapolated mechanical parameters were all <5%, indicating very probably no differences. The findings suggest that the simple computation method used here provides valid and reliable information on force and velocity produced during ballistic bench press, in line with that observed in laboratory conditions. This simple method is thus a practical tool, requiring only 3 simple parameters (upper-limb mass, barbell flight height, and push-off distance).

Direction-specific recruitment of rotator cuff muscles during bench press and row.

PubMed

Wattanaprakornkul, Duangjai; Halaki, Mark; Cathers, Ian; Ginn, Karen A

2011-12-01

Recent studies indicate that rotator cuff (RC) muscles are recruited in a reciprocal, direction-specific pattern during shoulder flexion and extension exercises. The main purpose of this study was to determine if similar reciprocal RC recruitment occurs during bench press (flexion-like) and row (extension-like) exercises. In addition, shoulder muscle activity was comprehensively compared between bench press and flexion; row and extension; and bench press and row exercises. Electromyographic (EMG) activity was recorded from 9 shoulder muscles sites in 15 normal volunteers. All exercises were performed at 20, 50 and 70% of subjects' maximal load. EMG data were normalized to standard maximal voluntary contractions. Infraspinatus activity was significantly higher than subscapularis during bench press, with the converse pattern during the row exercise. Significant differences in activity levels were found in pectoralis major, deltoid and trapezius between the bench press and flexion exercises and in lower trapezius between the row and extension exercises. During bench press and row exercises, the recruitment pattern in each active muscle did not vary with load. During bench press and row exercises, RC muscles contract in a reciprocal direction-specific manner in their role as shoulder joint dynamic stabilizers to counterbalance antero-posterior translation forces. Copyright © 2011 Elsevier Ltd. All rights reserved.

Portable gas chromatograph-mass spectrometer

DOEpatents

Andresen, Brian D.; Eckels, Joel D.; Kimmons, James F.; Myers, David W.

1996-01-01

A gas chromatograph-mass spectrometer (GC-MS) for use as a field portable organic chemical analysis instrument. The GC-MS is designed to be contained in a standard size suitcase, weighs less than 70 pounds, and requires less than 600 watts of electrical power at peak power (all systems on). The GC-MS includes: a conduction heated, forced air cooled small bore capillary gas chromatograph, a small injector assembly, a self-contained ion/sorption pump vacuum system, a hydrogen supply, a dual computer system used to control the hardware and acquire spectrum data, and operational software used to control the pumping system and the gas chromatograph. This instrument incorporates a modified commercial quadrupole mass spectrometer to achieve the instrument sensitivity and mass resolution characteristic of laboratory bench top units.

Evaluating Upper-Body Strength and Power From a Single Test: The Ballistic Push-up.

PubMed

Wang, Ran; Hoffman, Jay R; Sadres, Eliahu; Bartolomei, Sandro; Muddle, Tyler W D; Fukuda, David H; Stout, Jeffrey R

2017-05-01

Wang, R, Hoffman, JR, Sadres, E, Bartolomei, S, Muddle, TWD, Fukuda, DH, and Stout, JR. Evaluating upper-body strength and power from a single test: the ballistic push-up. J Strength Cond Res 31(5): 1338-1345, 2017-The purpose of this study was to examine the reliability of the ballistic push-up (BPU) exercise and to develop a prediction model for both maximal strength (1 repetition maximum [1RM]) in the bench press exercise and upper-body power. Sixty recreationally active men completed a 1RM bench press and 2 BPU assessments in 3 separate testing sessions. Peak and mean force, peak and mean rate of force development, net impulse, peak velocity, flight time, and peak and mean power were determined. Intraclass correlation coefficients were used to examine the reliability of the BPU. Stepwise linear regression was used to develop 1RM bench press and power prediction equations. Intraclass correlation coefficient's ranged from 0.849 to 0.971 for the BPU measurements. Multiple regression analysis provided the following 1RM bench press prediction equation: 1RM = 0.31 × Mean Force - 1.64 × Body Mass + 0.70 (R = 0.837, standard error of the estimate [SEE] = 11 kg); time-based power prediction equation: Peak Power = 11.0 × Body Mass + 2012.3 × Flight Time - 338.0 (R = 0.658, SEE = 150 W), Mean Power = 6.7 × Body Mass + 1004.4 × Flight Time - 224.6 (R = 0.664, SEE = 82 W); and velocity-based power prediction equation: Peak Power = 8.1 × Body Mass + 818.6 × Peak Velocity - 762.0 (R = 0.797, SEE = 115 W); Mean Power = 5.2 × Body Mass + 435.9 × Peak Velocity - 467.7 (R = 0.838, SEE = 57 W). The BPU is a reliable test for both upper-body strength and power. Results indicate that the mean force generated from the BPU can be used to predict 1RM bench press, whereas peak velocity and flight time measured during the BPU can be used to predict upper-body power. These findings support the potential use of the BPU as a valid method to evaluate upper-body strength and power.

Comparison of concentric and eccentric bench press repetitions to failure.

PubMed

Kelly, Stephen B; Brown, Lee E; Hooker, Steven P; Swan, Pamela D; Buman, Matthew P; Alvar, Brent A; Black, Laurie E

2015-04-01

Eccentric muscle actions (ECC) are characterized by muscle lengthening, despite actin-myosin crossbridge formation. Muscles acting eccentrically are capable of producing higher levels of force compared with muscles acting concentrically. The purpose of this study was to determine whether ECC bench press yields greater strength than concentric (CON) as determined by 1 repetition maximum (1RM). Additionally, a comparison was made examining differences in the number of repetitions to failure at different relative intensities of 1RM. Thirty healthy men (age = 24.63 ± 5.6 years) were tested for 1RM in CON and ECC bench press and the number of repetitions completed at 60, 70, 80, and 90% 1RM. For CON repetitions, the weight was mechanically lowered to the chest, and the participant pressed it up until the elbows were fully extended. The ECC bench press consisted of lowering a barbell from a fully extended elbow position to the chest in a continuous controlled manner for 3 seconds as determined by electronic metronome. Paired t-tests showed that ECC 1RM (115.99 ± 31.08 kg) was significantly (p ≤ 0.05) greater than CON 1RM (93.56 ± 26.56 kg), and the number of repetitions completed at 90% 1RM was significantly (p ≤ 0.05) greater in ECC (7.67 ± 3.24) as compared with CON (4.57 ± 2.21). There were no significant differences in number of completed repetitions during CON and ECC bench press at 60, 70, and 80% 1RM. These data indicate that ECC actions yield increased force capabilities (∼120%) as compared with CON in the bench press and may be less prone to fatigue, especially at higher intensities. These differences suggest a need to develop unique strategies for training eccentrically.

The development of a repetition-load scheme for the eccentric-only bench press exercise.

PubMed

Moir, Gavin L; Erny, Kyle F; Davis, Shala E; Guers, John J; Witmer, Chad A

2013-01-01

The purpose of the present study was to develop a repetition-load scheme for the eccentric-only bench press exercise. Nine resistance trained men (age: 21.6 ± 1.0 years; 1-repetition maximum [RM] bench press: 137.7 ± 30.4 kg) attended four testing sessions during a four week period. During the first session each subject's 1-RM bench press load utilizing the stretch-shortening cycle was determined. During the remaining sessions they performed eccentric-only repetitions to failure using supra-maximal loads equivalent to 110%, 120% and 130% of their 1-RM value with a constant cadence (30 reps·min(-1)). Force plates and a three dimensional motion analysis system were used during these final three sessions in order to evaluate kinematic and kinetic variables. More repetitions were completed during the 110% 1-RM condition compared to the 130% 1-RM condition (p=0.01). Mean total work (p=0.046) as well as vertical force (p=0.049), vertical work (p=0.017), and vertical power output (p=0.05) were significantly greater during the 130% 1-RM condition compared to the 110% 1-RM condition. A linear function was fitted to the number of repetitions completed under each load condition that allowed the determination of the maximum number of repetitions that could be completed under other supra-maximal loads. This linear function predicted an eccentric-only 1-RM in the bench press with a load equivalent to 164.8% 1-RM, producing a load of 227.0 ± 50.0 kg. The repetition-load scheme presented here should provide a starting point for researchers to investigate the kinematic, kinetic and metabolic responses to eccentric-only bench press workouts.

The Development of a Repetition-Load Scheme for the Eccentric-Only Bench Press Exercise

PubMed Central

Moir, Gavin L.; Erny, Kyle F.; Davis, Shala E.; Guers, John J.; Witmer, Chad A.

2013-01-01

The purpose of the present study was to develop a repetition-load scheme for the eccentric-only bench press exercise. Nine resistance trained men (age: 21.6 ± 1.0 years; 1-repetition maximum [RM] bench press: 137.7 ± 30.4 kg) attended four testing sessions during a four week period. During the first session each subject’s 1-RM bench press load utilizing the stretch-shortening cycle was determined. During the remaining sessions they performed eccentric-only repetitions to failure using supra-maximal loads equivalent to 110%, 120% and 130% of their 1-RM value with a constant cadence (30 reps·min−1). Force plates and a three dimensional motion analysis system were used during these final three sessions in order to evaluate kinematic and kinetic variables. More repetitions were completed during the 110% 1-RM condition compared to the 130% 1-RM condition (p=0.01). Mean total work (p=0.046) as well as vertical force (p=0.049), vertical work (p=0.017), and vertical power output (p=0.05) were significantly greater during the 130% 1-RM condition compared to the 110% 1-RM condition. A linear function was fitted to the number of repetitions completed under each load condition that allowed the determination of the maximum number of repetitions that could be completed under other supra-maximal loads. This linear function predicted an eccentric-only 1-RM in the bench press with a load equivalent to 164.8% 1-RM, producing a load of 227.0 ± 50.0 kg. The repetition-load scheme presented here should provide a starting point for researchers to investigate the kinematic, kinetic and metabolic responses to eccentric-only bench press workouts. PMID:24235981

Preliminary investigation of air bubbling and dietary sulfur reduction to mitigate hydrogen sulfide and odor from swine waste.

PubMed

Clark, O Grant; Morin, Brent; Zhang, Yongcheng; Sauer, Willem C; Feddes, John J R

2005-01-01

When livestock manure slurry is agitated, the sudden release of hydrogen sulfide (H(2)S) can raise concentrations to dangerous levels. Low-level air bubbling and dietary S reduction were evaluated as methods for reducing peak H(2)S emissions from swine (Sus scrofa) manure slurry samples. In a first experiment, 15-L slurry samples were stored in bench-scale digesters and continuously bubbled with air at 0 (control), 5, or 10 mL min(-1) for 28 d. The 5-L headspace of each digester was also continuously ventilated at 40 mL min(-1) and the mean H(2)S concentration in the outlet air was <10 microL L(-1). On Day 28, the slurry was agitated suddenly. The peak H(2)S concentration exceeded instrument range (>120 microL L(-1)) from the control treatment, and was 47 and 3.4 microL L(-1) for the 5 and 10 mL min(-1) treatments, respectively. In a second experiment, individually penned barrows were fed rations with dietary S concentrations of 0.34, 0.24, and 0.15% (w/w). Slurry derived from each diet was bubbled with air in bench-scale digesters, as before, at 10 mL min(-1) for 12 d and the mean H(2)S concentration in the digester outlet air was 11 microL L(-1). On Day 12, the slurry was agitated but the H(2)S emissions did not change significantly. Both low-level bubbling of air through slurry and dietary S reduction appear to be viable methods for reducing peak H(2)S emissions from swine manure slurry at a bench scale, but these approaches must be validated at larger scales.

Instability of Hawaiian volcanoes: Chapter 4 in Characteristics of Hawaiian volcanoes

USGS Publications Warehouse

Denlinger, Roger P.; Morgan, Julia K.; Poland, Michael P.; Takahashi, T. Jane; Landowski, Claire M.

2014-01-01

All seaward flank movement occurs along a detachment fault, or décollement, that forms within the mixture of pelagic clays and volcaniclastic deposits on the old seafloor and pushes up a bench of debris along the distal margin of the flank. The offshore uplift that builds this bench is generated by décollement slip that terminates upward into the overburden along thrust faults. Finite strain and finite strength models for volcano growth on a low-friction décollement reproduce this bench structure, as well as much of the morphology and patterns of faulting observed on the actively growing volcanoes of Mauna Loa and Kīlauea. These models show how stress is stored within growing volcano flanks, but not how rapid, potentially seismic slip is triggered along their décollements. The imbalance of forces that triggers large, rapid seaward displacement of the flank after decades of creep may result either from driving forces that change rapidly, such as magma pressure gradients; from resisting forces that rapidly diminish with slip, such as those arising from coupling of pore pressure and dilatancy within décollement sediment; or, from some interplay between driving and resisting forces that produces flank motion. Our understanding of the processes of flank motion is limited by available data, though recent studies have increased our ability to quantitatively address flank instability and associated hazards.

Performance Evaluation of a Low-Cost, Real-Time Community Air Monitoring Station

EPA Science Inventory

The US EPA’s Village Green Project (VGP) is an example of using innovative technology to enable community-level low-cost real-time air pollution measurements. The VGP is an air monitoring system configured as a park bench located outside of a public library in Durham, NC. It co...

Muscle Force-Velocity Relationships Observed in Four Different Functional Tests.

PubMed

Zivkovic, Milena Z; Djuric, Sasa; Cuk, Ivan; Suzovic, Dejan; Jaric, Slobodan

2017-02-01

The aims of the present study were to investigate the shape and strength of the force-velocity relationships observed in different functional movement tests and explore the parameters depicting force, velocity and power producing capacities of the tested muscles. Twelve subjects were tested on maximum performance in vertical jumps, cycling, bench press throws, and bench pulls performed against different loads. Thereafter, both the averaged and maximum force and velocity variables recorded from individual trials were used for force-velocity relationship modeling. The observed individual force-velocity relationships were exceptionally strong (median correlation coefficients ranged from r = 0.930 to r = 0.995) and approximately linear independently of the test and variable type. Most of the relationship parameters observed from the averaged and maximum force and velocity variable types were strongly related in all tests (r = 0.789-0.991), except for those in vertical jumps (r = 0.485-0.930). However, the generalizability of the force-velocity relationship parameters depicting maximum force, velocity and power of the tested muscles across different tests was inconsistent and on average moderate. We concluded that the linear force-velocity relationship model based on either maximum or averaged force-velocity data could provide the outcomes depicting force, velocity and power generating capacity of the tested muscles, although such outcomes can only be partially generalized across different muscles.

Anthropometry as a predictor of bench press performance done at different loads.

PubMed

Caruso, John F; Taylor, Skyler T; Lutz, Brant M; Olson, Nathan M; Mason, Melissa L; Borgsmiller, Jake A; Riner, Rebekah D

2012-09-01

The purpose of our study was to examine the ability of anthropometric variables (body mass, total arm length, biacromial width) to predict bench press performance at both maximal and submaximal loads. Our methods required 36 men to visit our laboratory and submit to anthropometric measurements, followed by lifting as much weight as possible in good form one time (1 repetition maximum, 1RM) in the exercise. They made 3 more visits in which they performed 4 sets of bench presses to volitional failure at 1 of 3 (40, 55, or 75% 1RM) submaximal loads. An accelerometer (Myotest Inc., Royal Oak MI) measured peak force, velocity, and power after each submaximal load set. With stepwise multivariate regression, our 3 anthropometric variables attempted to explain significant amounts of variance for 13 bench press performance indices. For criterion measures that reached significance, separate Pearson product moment correlation coefficients further assessed if the strength of association each anthropometric variable had with the criterion was also significant. Our analyses showed that anthropometry explained significant amounts (p < 0.05) of variance for 8 criterion measures. It was concluded that body mass had strong univariate correlations with 1RM and force-related measures, total arm length was moderately associated with 1RM and criterion variables at the lightest load, whereas biacromial width had an inverse relationship with the peak number of repetitions performed per set at the 2 lighter loads. Practical applications suggest results may help coaches and practitioners identify anthropometric features that may best predict various measures of bench press prowess in athletes.

Validity of a Commercial Linear Encoder to Estimate Bench Press 1 RM from the Force-Velocity Relationship.

PubMed

Bosquet, Laurent; Porta-Benache, Jeremy; Blais, Jérôme

2010-01-01

The aim of this study was to assess the validity and accuracy of a commercial linear encoder (Musclelab, Ergotest, Norway) to estimate Bench press 1 repetition maximum (1RM) from the force - velocity relationship. Twenty seven physical education students and teachers (5 women and 22 men) with a heterogeneous history of strength training participated in this study. They performed a 1 RM test and a force - velocity test using a Bench press lifting task in a random order. Mean 1 RM was 61.8 ± 15.3 kg (range: 34 to 100 kg), while 1 RM estimated by the Musclelab's software from the force-velocity relationship was 56.4 ± 14.0 kg (range: 33 to 91 kg). Actual and estimated 1 RM were very highly correlated (r = 0.93, p<0.001) but largely different (Bias: 5.4 ± 5.7 kg, p < 0.001, ES = 1.37). The 95% limits of agreement were ±11.2 kg, which represented ±18% of actual 1 RM. It was concluded that 1 RM estimated from the force-velocity relationship was a good measure for monitoring training induced adaptations, but also that it was not accurate enough to prescribe training intensities. Additional studies are required to determine whether accuracy is affected by age, sex or initial level. Key pointsSome commercial devices allow to estimate 1 RM from the force-velocity relationship.These estimations are valid. However, their accuracy is not high enough to be of practical help for training intensity prescription.Day-to-day reliability of force and velocity measured by the linear encoder has been shown to be very high, but the specific reliability of 1 RM estimated from the force-velocity relationship has to be determined before concluding to the usefulness of this approach in the monitoring of training induced adaptations.

Validity of a Commercial Linear Encoder to Estimate Bench Press 1 RM from the Force-Velocity Relationship

PubMed Central

Bosquet, Laurent; Porta-Benache, Jeremy; Blais, Jérôme

2010-01-01

The aim of this study was to assess the validity and accuracy of a commercial linear encoder (Musclelab, Ergotest, Norway) to estimate Bench press 1 repetition maximum (1RM) from the force - velocity relationship. Twenty seven physical education students and teachers (5 women and 22 men) with a heterogeneous history of strength training participated in this study. They performed a 1 RM test and a force - velocity test using a Bench press lifting task in a random order. Mean 1 RM was 61.8 ± 15.3 kg (range: 34 to 100 kg), while 1 RM estimated by the Musclelab’s software from the force-velocity relationship was 56.4 ± 14.0 kg (range: 33 to 91 kg). Actual and estimated 1 RM were very highly correlated (r = 0.93, p<0.001) but largely different (Bias: 5.4 ± 5.7 kg, p < 0.001, ES = 1.37). The 95% limits of agreement were ±11.2 kg, which represented ±18% of actual 1 RM. It was concluded that 1 RM estimated from the force-velocity relationship was a good measure for monitoring training induced adaptations, but also that it was not accurate enough to prescribe training intensities. Additional studies are required to determine whether accuracy is affected by age, sex or initial level. Key points Some commercial devices allow to estimate 1 RM from the force-velocity relationship. These estimations are valid. However, their accuracy is not high enough to be of practical help for training intensity prescription. Day-to-day reliability of force and velocity measured by the linear encoder has been shown to be very high, but the specific reliability of 1 RM estimated from the force-velocity relationship has to be determined before concluding to the usefulness of this approach in the monitoring of training induced adaptations. PMID:24149641

INTEGRATION OF PHOTOCATALYTIC OXIDATION WITH AIR STRIPPING OF CONTAMINATED AQUIFERS

EPA Science Inventory

Bench scale laboratory studies and pilot scale studies in a simulated field-test situation were performed to evaluate the integration of gas-solid ultaviolet (UV) photocatalytic oxidation (PCO) downstream if an air stripper unit as a technology for cost-effectively treating water...

Tests of the Daimler D-IVa Engine at a High Altitude Test Bench

NASA Technical Reports Server (NTRS)

Noack, W G

1920-01-01

Reports of tests of a Daimler IVa engine at the test-bench at Friedrichshafen, show that the decrease of power of that engine, at high altitudes, was established, and that the manner of its working when air is supplied at a certain pressure was explained. These tests were preparatory to the installation of compressors in giant aircraft for the purpose of maintaining constant power at high altitudes.

Errors of car wheels rotation rate measurement using roller follower on test benches

NASA Astrophysics Data System (ADS)

Potapov, A. S.; Svirbutovich, O. A.; Krivtsov, S. N.

2018-03-01

The article deals with rotation rate measurement errors, which depend on the motor vehicle rate, on the roller, test benches. Monitoring of the vehicle performance under operating conditions is performed on roller test benches. Roller test benches are not flawless. They have some drawbacks affecting the accuracy of vehicle performance monitoring. Increase in basic velocity of the vehicle requires increase in accuracy of wheel rotation rate monitoring. It determines the degree of accuracy of mode identification for a wheel of the tested vehicle. To ensure measurement accuracy for rotation velocity of rollers is not an issue. The problem arises when measuring rotation velocity of a car wheel. The higher the rotation velocity of the wheel is, the lower the accuracy of measurement is. At present, wheel rotation frequency monitoring on roller test benches is carried out by following-up systems. Their sensors are rollers following wheel rotation. The rollers of the system are not kinematically linked to supporting rollers of the test bench. The roller follower is forced against the wheels of the tested vehicle by means of a spring-lever mechanism. Experience of the test bench equipment operation has shown that measurement accuracy is satisfactory at small rates of vehicles diagnosed on roller test benches. With a rising diagnostics rate, rotation velocity measurement errors occur in both braking and pulling modes because a roller spins about a tire tread. The paper shows oscillograms of changes in wheel rotation velocity and rotation velocity measurement system’s signals when testing a vehicle on roller test benches at specified rates.

Portable gas chromatograph-mass spectrometer

DOEpatents

Andresen, B.D.; Eckels, J.D.; Kimmons, J.F.; Myers, D.W.

1996-06-11

A gas chromatograph-mass spectrometer (GC-MS) is described for use as a field portable organic chemical analysis instrument. The GC-MS is designed to be contained in a standard size suitcase, weighs less than 70 pounds, and requires less than 600 watts of electrical power at peak power (all systems on). The GC-MS includes: a conduction heated, forced air cooled small bore capillary gas chromatograph, a small injector assembly, a self-contained ion/sorption pump vacuum system, a hydrogen supply, a dual computer system used to control the hardware and acquire spectrum data, and operational software used to control the pumping system and the gas chromatograph. This instrument incorporates a modified commercial quadrupole mass spectrometer to achieve the instrument sensitivity and mass resolution characteristic of laboratory bench top units. 4 figs.

Mechanical Performance of Two Left Atrial Appendage Occlusion Systems: In Vitro Comparison of Tug Force, Radial Force, Sealing and Deformation.

PubMed

Menne, Matthias F; Schrickel, Jan W; Nickenig, Georg; Al-Kassou, Baravan; Nelles, Dominik; Schmitz-Rode, Thomas; Steinseifer, Ulrich; Sedaghat, Alexander

2018-05-24

The aim of this study was to establish in vitro bench-tests of left atrial appendage occlusion (LAAo) devices regarding tug force, radial force and sealing capacity. Two LAAo devices, namely the WATCHMAN™ and the Occlutech ® , of three different sizes underwent testing in novel dedicated in vitro setups. Radial force was assessed in a commercial radial force tester. At baseline, tug force of the WATCHMAN™ was significantly higher when compared to Occlutech ® for all devices. Repeated resheathing resulted in a reduction of device-diameter in the WATCHMAN™ devices of max. 7.9%, whereas diameters of Occlutech ® occluders remained unchanged. Tug force was not significantly impacted by resheathing in both devices. At baseline, sealing capacity in a bench-test using silicone LAA-models did not differ between the devices. Resheathing lead to an in vitro loss of sealing capacity of the WATCHMAN™ devices, increasing with resheathing and resulting in a max. peridevice leak of 91.1 ± 7.9%. Radial force was higher for the Occlutech ® devices and decreased for WATCHMAN™ occluders after resheathing. The WATCHMAN™ occluder series showed progressive deformation, increased peridevice leakage and decreased radial force after resheathing, presumably as a result of diameter reduction. Tug force of the WATCHMAN™ was not impaired by resheathing and was significantly higher than that of the Occlutech ® device.

Muscle Force-Velocity Relationships Observed in Four Different Functional Tests

PubMed Central

Zivkovic, Milena Z.; Djuric, Sasa; Cuk, Ivan; Suzovic, Dejan; Jaric, Slobodan

2017-01-01

Abstract The aims of the present study were to investigate the shape and strength of the force-velocity relationships observed in different functional movement tests and explore the parameters depicting force, velocity and power producing capacities of the tested muscles. Twelve subjects were tested on maximum performance in vertical jumps, cycling, bench press throws, and bench pulls performed against different loads. Thereafter, both the averaged and maximum force and velocity variables recorded from individual trials were used for force–velocity relationship modeling. The observed individual force-velocity relationships were exceptionally strong (median correlation coefficients ranged from r = 0.930 to r = 0.995) and approximately linear independently of the test and variable type. Most of the relationship parameters observed from the averaged and maximum force and velocity variable types were strongly related in all tests (r = 0.789-0.991), except for those in vertical jumps (r = 0.485-0.930). However, the generalizability of the force-velocity relationship parameters depicting maximum force, velocity and power of the tested muscles across different tests was inconsistent and on average moderate. We concluded that the linear force-velocity relationship model based on either maximum or averaged force-velocity data could provide the outcomes depicting force, velocity and power generating capacity of the tested muscles, although such outcomes can only be partially generalized across different muscles. PMID:28469742

Setup of a photomultiplier tube test bench for LHAASO-KM2A

NASA Astrophysics Data System (ADS)

Wang, Xu; Zhang, Zhong-Quan; Tian, Ye; Du, Yan-Yan; Zhao, Xiao; Shen, Fu-Wang; Li, Chang-Yu; Sun, Yan-Sheng; Feng, Cun-Feng

2016-08-01

To fulfill the requirements for testing the photomultiplier tubes (PMTs) of the electromagnetic detector at the Large High Altitude Air Shower Observatory (LHAASO), a multi-functional PMT test bench with a two-dimensional scanning system has been developed. With this 2D scanning system, 16 PMTs can be scanned simultaneously for characteristics tests, including uniformity, cathode transit time difference, single photo-electron spectrum, gain vs. high voltage, linear behavior and dark noise. The programmable hardware and intelligent software of the test bench make it convenient to use and provide reliable results. The test methods are described in detail and primary results are presented. Supported by NSFC (11075096) SDNFS (ZR2011AM007), China

EPA’s Village Green Project: New Directions

EPA Science Inventory

The US EPA’s Village Green Project (VGP) is an example of using innovative technology to enable community-level, real-time air pollution measurements using low-cost sensor technologies. The VGP is an air monitoring system configured as a park bench located outside of a public lib...

Strength and power determinants of grinding performance in America's Cup sailors.

PubMed

Pearson, Simon N; Hume, Patria A; Cronin, John B; Slyfield, David

2009-09-01

The purpose grinding is a physically demanding component of America's Cup sailing that is important to overall team performance, but little research is available on the determinants of grinding performance. We examined the relationship between various measures of muscular performance and the performance of upper-body grinding. Eleven elite male America's Cup sailors (33.9 +/- 5.5 yr, 97.8 +/- 12.5 kg, 186.0 +/- 7.1 cm) who performed grinding as part of their on-board role with extensive strength training experience participated in this study. Muscular performance testing examined the force, velocity, and power capabilities of the upper-body musculature, with upper-body push (bench press) and pull (bench pull) movements performed across loads of 10-100% of 1 repetition maximum (1RM). Functional grinding performance was examined for both forward and backward grinding and at 2 different resistances (moderate = 48 N x m, heavy = 68 N x m) using a land-based ergometer. Bench press 1RM and maximum force capability were the measures demonstrating the strongest correlation with forward grinding performance (r = 0.88-0.99 and 0.87-0.99, respectively), with the relationship increasing with grinding load. For backward grinding, there was a very strong relationship with bench pull maximum power (r = 0.85-0.98) in addition to 1RM (r = 0.90-0.95) and maximum force (r = 0.87-0.95). It appears that although maximal strength is a crucial muscular performance characteristic for grinding performance in all conditions, for backward grinding, there is the additional need to focus on the development of speed strength/power to maximize performance gains. This information was used by the Emirates Team New Zealand physical conditioner to develop a conditioning intervention to help improve grinding performance.

An Investigation of the Mechanics and Sticking Region of a One-Repetition Maximum Close-Grip Bench Press versus the Traditional Bench Press

PubMed Central

Lockie, Robert G.; Callaghan, Samuel J.; Moreno, Matthew R.; Risso, Fabrice G.; Liu, Tricia M.; Stage, Alyssa A.; Birmingham-Babauta, Samantha A.; Stokes, John J.; Giuliano, Dominic V.; Lazar, Adrina; Davis, DeShaun L.; Orjalo, Ashley J.

2017-01-01

The close-grip bench press (CGBP) is a variation of the traditional bench press (TBP) that uses a narrower grip (~95% of biacromial distance (BAD)) and has potential application for athletes performing explosive arm actions from positions where the hands are held close to the torso. Limited research has investigated CGBP mechanics compared to the TBP. Twenty-seven resistance-trained individuals completed a one-repetition maximum TBP and CGBP. The TBP was performed with the preferred grip; the CGBP with a grip width of 95% BAD. A linear position transducer measured lift distance and duration; peak and mean power, velocity, and force; distance and time when peak power occurred; and work. Pre-sticking region (PrSR), sticking region, and post-sticking region distance and duration for each lift was measured. A repeated measures ANOVA was used to derive differences between TBP and CGBP mechanics (p < 0.01); effect sizes (d) were also calculated. A greater load was lifted in the TBP, thus mean force was greater (d = 0.16–0.17). Peak power and velocity were higher in the CGBP, which had a longer PrSR distance (d = 0.49–1.32). The CGBP could emphasize power for athletes that initiate explosive upper-body actions with the hands positioned close to the torso.

Experimental and theoretical study of friction torque from radial ball bearings

NASA Astrophysics Data System (ADS)

Geonea, Ionut; Dumitru, Nicolae; Dumitru, Ilie

2017-10-01

In this paper it is presented a numerical simulation and an experimental study of total friction torque from radial ball bearings. For this purpose it is conceived a virtual CAD model of the experimental test bench for bearing friction torque measurement. The virtual model it is used for numerical simulation in Adams software, that allows dynamic study of multi-body systems and in particularly with facility Adams Machinery of dynamic behavior of machine parts. It is manufactured an experimental prototype of the test bench for radial ball bearings friction torque measurement. In order to measure the friction torque of the tested bearings it is used an equal resistance elastic beam element, with strain gauge transducer to measure bending deformations. The actuation electric motor of the bench has the shaft mounted on two bearings and the motor housing is fixed to the free side of the elastic beam, which is bended by a force proportional with the total friction torque. The beam elastic element with strain gauge transducer is calibrated in order to measure the force occurred. Experimental determination of the friction torque is made for several progressive radial loads. It is established the correlation from the friction torque and bearing radial load. The bench allows testing of several types and dimensions of radial bearings, in order to establish the bearing durability and of total friction torque.

Influence of Dissipative Particle Dynamics parameters and wall models on planar micro-channel flows

NASA Astrophysics Data System (ADS)

Wang, Yuyi; She, Jiangwei; Zhou, Zhe-Wei; microflow Group Team

2017-11-01

Dissipative Particle Dynamics (DPD) is a very effective approach in simulating mesoscale hydrodynamics. The influence of solid boundaries and DPD parameters are typically very strong in DPD simulations. The present work studies a micro-channel Poisseuille flow. Taking the neutron scattering experiment and molecular dynamics simulation result as bench mark, the DPD results of density distribution and velocity profile are systematically studied. The influence of different levels of coarse-graining, the number densities of wall and fluid, conservative force coefficients, random and dissipative force coefficients, different wall model and reflective boundary conditions are discussed. Some mechanisms behind such influences are discussed and the artifacts in the simulation are identified with the bench mark. Chinese natural science foundation (A020405).

Livestock air treatment using PVA-coated powdered activated carbon biofilter

USDA-ARS?s Scientific Manuscript database

The efficacy of polyvinyl alcohol (PVA) biofilters was studied using bench-scale biofilters and air from aerobically-treated swine manure. The PVA-coated powdered activated carbon particles showed excellent properties as a biofiltration medium: water holding capacity of 1.39 g H2O/g-dry PVA; wet por...

Upper and Lower Body Muscle Power Increases After 3-Month Resistance Training in Overweight and Obese Men

PubMed Central

Zemková, Erika; Kyselovičová, Oľga; Jeleň, Michal; Kováčiková, Zuzana; Ollé, Gábor; Štefániková, Gabriela; Vilman, Tomáš; Baláž, Miroslav; Kurdiová, Timea; Ukropec, Jozef; Ukropcová, Barbara

2016-01-01

This study evaluates the effect of 3 months resistance and aerobic training on muscle strength and power in 17 male overweight and obese men. Subjects underwent either a resistance or aerobic training for a period of 3 months (three sessions per week). Peak isometric force, rate of force development, peak power and height of countermovement and squat jumps, reactive strength index, and mean power in the concentric phase of bench presses were all assessed prior to and after completing the training program. Results identified a significant increase of mean power during both countermovement bench presses at 30 kg (18.6%, p = .021), 40 kg (14.6%, p = .033), and 50 kg (13.1%, p = .042) and concentric-only bench presses at 30 kg (19.6%, p = .017) and 40 kg (13.9%, p = .037) after the resistance training. There was also a significant increase in the height of the jump (12.8%, p = .013), peak power (10.1%, p = .026), and peak velocity (9.7%, p = .037) during the countermovement jump and height of the jump (11.8%, p = .019), peak power (9.6%, p = .032), and peak velocity (9.5%, p = .040) during the squat jump. There were no significant changes in the reactive strength index, peak force, and the rate of force development after the resistance training. The aerobic group failed to show any significant improvements in these parameters. It may be concluded that 3 months of resistance training without caloric restriction enhances upper and lower body muscle power in overweight and obese men. PMID:27530821

Is it the time to study air pollution effects under environmental conditions? A case study to support the shift of in vitro toxicology from the bench to the field.

PubMed

Gualtieri, Maurizio; Grollino, Maria Giuseppa; Consales, Claudia; Costabile, Francesca; Manigrasso, Maurizio; Avino, Pasquale; Aufderheide, Michaela; Cordelli, Eugenia; Di Liberto, Luca; Petralia, Ettore; Raschellà, Giuseppe; Stracquadanio, Milena; Wiedensohler, Alfred; Pacchierotti, Francesca; Zanini, Gabriele

2018-09-01

Air pollution and particulate matter are recognised cause of increased disease incidence in exposed population. The toxicological processes underlying air pollution associated effects have been investigated by in vivo and/or in vitro experimentation. The latter is usually performed by exposing cells cultured under submerged condition to particulate matter concentration quite far from environmental exposure expected in humans. Here we report for the first time the feasibility of a direct exposure of air liquid interface cultured cells to environmental concentration of particulate matter. Inflammatory proteins release was analysed in cell medium while differential expression of selected genes was analysed in cells. Significant association of anti-oxidant genes was observed with secondary and aged aerosol, while cytochrome activation with primary and PAHs enriched ultrafine particles. The results obtained clearly show the opportunity to move from the lab bench to the field for properly understanding the toxicological effects also of ultrafine particles on selected in vitro models. Copyright © 2018 Elsevier Ltd. All rights reserved.

Transitioning Active Flow Control to Applications

NASA Technical Reports Server (NTRS)

Joslin, Ronald D.; Horta, Lucas G.; Chen, Fang-Jenq

1999-01-01

Active Flow Control Programs at NASA, the U.S. Air Force, and DARPA have been initiated with the goals of obtaining revolutionary advances in aerodynamic performance and maneuvering compared to conventional approaches. These programs envision the use of actuators, sensors, and controllers on applications such as aircraft wings/tails, engine nacelles, internal ducts, nozzles, projectiles, weapons bays, and hydrodynamic vehicles. Anticipated benefits of flow control include reduced weight, part count, and operating cost and reduced fuel burn (and emissions), noise and enhanced safety if the sensors serve a dual role of flow control and health monitoring. To get from the bench-top or laboratory test to adaptive distributed control systems on realistic applications, reliable validated design tools are needed in addition to sub- and large-scale wind-tunnel and flight experiments. This paper will focus on the development of tools for active flow control applications.

Potential of mean force for electrical conductivity of dense plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Starrett, C. E.

The electrical conductivity in dense plasmas can be calculated with the relaxation-time approximation provided that the interaction potential between the scattering electron and the ion is known. To date there has been considerable uncertainty as to the best way to define this interaction potential so that it correctly includes the effects of ionic structure, screening by electrons and partial ionization. The current approximations lead to significantly different results with varying levels of agreement when compared to bench-mark calculations and experiments. Here, we present a new way to define this potential, drawing on ideas from classical fluid theory to define amore » potential of mean force. This new potential results in significantly improved agreement with experiments and bench-mark calculations, and includes all the aforementioned physics self-consistently.« less

Potential of mean force for electrical conductivity of dense plasmas

DOE PAGES

Starrett, C. E.

2017-09-28

The electrical conductivity in dense plasmas can be calculated with the relaxation-time approximation provided that the interaction potential between the scattering electron and the ion is known. To date there has been considerable uncertainty as to the best way to define this interaction potential so that it correctly includes the effects of ionic structure, screening by electrons and partial ionization. The current approximations lead to significantly different results with varying levels of agreement when compared to bench-mark calculations and experiments. Here, we present a new way to define this potential, drawing on ideas from classical fluid theory to define amore » potential of mean force. This new potential results in significantly improved agreement with experiments and bench-mark calculations, and includes all the aforementioned physics self-consistently.« less

Potential of mean force for electrical conductivity of dense plasmas

NASA Astrophysics Data System (ADS)

Starrett, C. E.

2017-12-01

The electrical conductivity in dense plasmas can be calculated with the relaxation-time approximation provided that the interaction potential between the scattering electron and the ion is known. To date there has been considerable uncertainty as to the best way to define this interaction potential so that it correctly includes the effects of ionic structure, screening by electrons and partial ionization. Current approximations lead to significantly different results with varying levels of agreement when compared to bench-mark calculations and experiments. We present a new way to define this potential, drawing on ideas from classical fluid theory to define a potential of mean force. This new potential results in significantly improved agreement with experiments and bench-mark calculations, and includes all the aforementioned physics self-consistently.

Electrophysiological assessment of piano players' back extensor muscles on a regular piano bench and chair with back rest.

PubMed

Honarmand, Kavan; Minaskanian, Rafael; Maboudi, Seyed Ebrahim; Oskouei, Ali E

2018-01-01

[Purpose] Sitting position is the dominant position for a professional pianist. There are many static and dynamic forces which affect musculoskeletal system during sitting. In prolonged sitting, these forces are harmful. The aim of this study was to compare pianists' back extensor muscles activity during playing piano while sitting on a regular piano bench and a chair with back rest. [Subjects and Methods] Ten professional piano players (mean age 25.4 ± 5.28, 60% male, 40% female) performed similar tasks for 5 hours in two sessions: one session sitting on a regular piano bench and the other sitting on a chair with back rest. In each session, muscular activity was assessed in 3 ways: 1) recording surface electromyography of the back-extensor muscles at the beginning and end of each session, 2) isometric back extension test, and 3) musculoskeletal discomfort questionnaire. [Results] There were significantly lesser muscular activity, more ability to perform isometric back extension and better personal comfort while sitting on a chair with back rest. [Conclusion] Decreased muscular activity and perhaps fatigue during prolonged piano playing on a chair with back rest may reduce acquired musculoskeletal disorders amongst professional pianists.

Electrophysiological assessment of piano players’ back extensor muscles on a regular piano bench and chair with back rest

PubMed Central

Honarmand, Kavan; Minaskanian, Rafael; Maboudi, Seyed Ebrahim; Oskouei, Ali E.

2018-01-01

[Purpose] Sitting position is the dominant position for a professional pianist. There are many static and dynamic forces which affect musculoskeletal system during sitting. In prolonged sitting, these forces are harmful. The aim of this study was to compare pianists’ back extensor muscles activity during playing piano while sitting on a regular piano bench and a chair with back rest. [Subjects and Methods] Ten professional piano players (mean age 25.4 ± 5.28, 60% male, 40% female) performed similar tasks for 5 hours in two sessions: one session sitting on a regular piano bench and the other sitting on a chair with back rest. In each session, muscular activity was assessed in 3 ways: 1) recording surface electromyography of the back-extensor muscles at the beginning and end of each session, 2) isometric back extension test, and 3) musculoskeletal discomfort questionnaire. [Results] There were significantly lesser muscular activity, more ability to perform isometric back extension and better personal comfort while sitting on a chair with back rest. [Conclusion] Decreased muscular activity and perhaps fatigue during prolonged piano playing on a chair with back rest may reduce acquired musculoskeletal disorders amongst professional pianists. PMID:29410569

Force-Velocity Relationship of Upper Body Muscles: Traditional Versus Ballistic Bench Press.

PubMed

García-Ramos, Amador; Jaric, Slobodan; Padial, Paulino; Feriche, Belén

2016-04-01

This study aimed to (1) evaluate the linearity of the force-velocity relationship, as well as the reliability of maximum force (F0), maximum velocity (V0), slope (a), and maximum power (P0); (2) compare these parameters between the traditional and ballistic bench press (BP); and (3) determine the correlation of F0 with the directly measured BP 1-repetition maximum (1RM). Thirty-two men randomly performed 2 sessions of traditional BP and 2 sessions of ballistic BP during 2 consecutive weeks. Both the maximum and mean values of force and velocity were recorded when loaded by 20-70% of 1RM. All force-velocity relationships were strongly linear (r > .99). While F0 and P0 were highly reliable (ICC: 0.91-0.96, CV: 3.8-5.1%), lower reliability was observed for V0 and a (ICC: 0.49-0.81, CV: 6.6-11.8%). Trivial differences between exercises were found for F0 (ES: < 0.2), however the a was higher for the traditional BP (ES: 0.68-0.94), and V0 (ES: 1.04-1.48) and P0 (ES: 0.65-0.72) for the ballistic BP. The F0 strongly correlated with BP 1RM (r: 0.915-0.938). The force-velocity relationship is useful to assess the upper body maximal capabilities to generate force, velocity, and power.

Relationship between isometric and dynamic strength in recreationally trained men.

PubMed

McGuigan, Michael R; Newton, Michael J; Winchester, Jason B; Nelson, Arnold G

2010-09-01

The purpose of this investigation was to examine the relationships between measures of maximal isometric force (peak force [PF]), rate of force development (RFD), vertical jump performance (VJ) and 1-repetition maximum (1RM) strength in recreationally trained men. The subjects in this study were 26 men ([mean +/- SD]: age 22 +/- 1 years; height 175 +/- 7 cm; mass 90 +/- 10 kg). They were tested for PF using the isometric midthigh pull exercise. The 1RM for the squat and bench press exercise were determined as a measure of dynamic strength. Explosive strength was measured as RFD from the isometric force-time curve. Correlations between the variables were calculated using Pearson product moment correlation coefficient. There was a nearly perfect correlation between measures of PF and 1RM squat (r = 0.97, p < 0.05) and 1RM bench press (r = 0.99, p < 0.05). The correlations were very strong between VJ and PF (r = 0.72, p < 0.05) and 1RM bench press (r = 0.70, p < 0.05). There were also strong correlations between VJ and 1RM squat (r = 0.69, p < 0.05). There were no significant correlations with RFD. The results showed that isometric maximum strength determined during the isometric midthigh pull test correlated well with 1RM and VJ testing. However, RFD measured during the same test did not appear to correlate as well with other measures. The isometric midthigh pull provides an efficient method for assessing strength in recreationally trained individuals. Practitioners wishing to obtain performance data related to maximum strength may wish to consider isometric testing as a less time intensive method of testing.

Depositional history of the Fire Clay coal bed (Late Duckmantian), Eastern Kentucky, USA

USGS Publications Warehouse

Greb, S.F.; Eble, C.F.; Hower, J.C.

1999-01-01

More than 3800 coal thickness measurements, proximate analyses from 97 localities, and stratigraphic and sedimentological analyses from more than 300 outcrops and cores were used in conjunction with previously reported palynological and petrographic studies to map individual benches of the coal and document bench-scale variability in the Fire Clay (Hazard No. 4) coal bed across a 1860 km2 area of the Eastern Kentucky Coal Field. The bench architecture of the Fire Clay coal bed consists of uncommon leader benches, a persistent but variable lower bench, a widespread, and generally thick upper bench, and local, variable rider benches. Rheotrophic conditions are inferred for the leader benches and lower bench based on sedimentological associations, mixed palynomorph assemblages, locally common cannel coal layers, and generally high ash yields. The lower bench consistently exhibits vertical variability in petrography and palynology that reflects changing trophic conditions as topographic depressions infilled. Infilling also led to unconfined flooding and ultimately the drowning of the lower bench mire. The drowned mire was covered by an air-fall volcanic-ash deposit, which produced the characteristic flint clay parting. The extent and uniform thickness of the parting suggests that the ash layer was deposited in water on a relatively flat surface without a thick canopy or extensive standing vegetation across most of the study area. Ash deposits led to regional ponding and establishment of a second planar mire. Because the topography had become a broadly uniform, nutrient-rich surface, upper-bench peats became widespread with large areas of the mire distant to clastic sources. Vertical sections of thick (> 70 cm), low-ash yield, upper coal bench show a common palynomorph change from arborescent lycopod dominance upward to fern and densospore-producing, small lycopod dominance, inferred as a shift from planar to ombrotrophic mire phases. Domed mires appear to have been surrounded by wide areas of planar mires, where the coal was thinner (< 70 cm), higher in ash yield, and dominated by arborescent lycopods. Rectangular thickness trends suggest that syndepositional faulting influenced peat accumulation, and possibly the position of the domed mire phase. Faulting also influenced post-depositional clastic environments of deposition, resulting in sandstone channels with angular changes in orientation. Channels and lateral facies were locally draped by high-ash-yield rider coal benches, which sometimes merged with the upper coal bench. These arborescent-lycopod dominant rider coal benches were profoundly controlled by palcotopography, much like the leader coal benches. Each of the benches of coal documented here represent distinctly different mires that came together to form the Fire Clay coal bed, rather than a single mire periodically split by clastic influx. This is significant as each bench of the coal has its own characteristics, which contribute to the total coal characteristics. The large data set allows interpretation of both vertical and lateral limits to postulated domed phases in the upper coal bench, and to the delineation of subtle tectonic structures that allow for meaningful thickness projections beyond the limits of present mining.A study was conducted to analyze the depositional history of the Fire Clay coal bed in the eastern Kentucky coal field. The study involved over 3800 coal thickness measurements, proximate analyses from 97 localities, and stratigraphic and sedimentological analyses from more than 300 outcrops and cores in conjunction with previously reported palynological and petrographic studies to map individual benches of the coal and document bench-scale variability.

Sensory feedback in prosthetics: a standardized test bench for closed-loop control.

PubMed

Dosen, Strahinja; Markovic, Marko; Hartmann, Cornelia; Farina, Dario

2015-03-01

Closing the control loop by providing sensory feedback to the user of a prosthesis is an important challenge, with major impact on the future of prosthetics. Developing and comparing closed-loop systems is a difficult task, since there are many different methods and technologies that can be used to implement each component of the system. Here, we present a test bench developed in Matlab Simulink for configuring and testing the closed-loop human control system in standardized settings. The framework comprises a set of connected generic blocks with normalized inputs and outputs, which can be customized by selecting specific implementations from a library of predefined components. The framework is modular and extensible and it can be used to configure, compare and test different closed-loop system prototypes, thereby guiding the development towards an optimal system configuration. The use of the test bench was demonstrated by investigating two important aspects of closed-loop control: performance of different electrotactile feedback interfaces (spatial versus intensity coding) during a pendulum stabilization task and feedforward methods (joystick versus myocontrol) for force control. The first experiment demonstrated that in the case of trained subjects the intensity coding might be superior to spatial coding. In the second experiment, the control of force was rather poor even with a stable and precise control interface (joystick), demonstrating that inherent characteristics of the prosthesis can be an important limiting factor when considering the overall effectiveness of the closed-loop control. The presented test bench is an important instrument for investigating different aspects of human manual control with sensory feedback.

Relationships among peak power output, peak bar velocity, and mechanomyographic amplitude during the free-weight bench press exercise.

PubMed

Stock, Matt S; Beck, Travis W; Defreitas, Jason M; Dillon, Michael A

2010-10-01

The purpose of this study was to examine the relationships among mechanomyographic (MMG) amplitude, power output, and bar velocity during the free-weight bench press exercise. Twenty-one resistance-trained men [one-repetition maximum (1-RM) bench press = 125.4+18.4 kg] performed bench press muscle actions as explosively as possible from 10% to 90% of the 1-RM while peak power output and peak bar velocity were assessed with a TENDO Weightlifting Analyzer. During each muscle action, surface MMG signals were detected from the right and left pectoralis major and triceps brachii, and the concentric portion of the range of motion was selected for analysis. Results indicated that power output increased from 10% to 50% 1-RM, followed by decreases from 50% to 90% 1-RM, but MMG amplitude for each of the muscles increased from 10 to 80% 1-RM. The results of this study indicate that during the free-weight bench press exercise, MMG amplitude was not related to power output, but was inversely related to bar velocity and directly related to the external load being lifted. In future research, coaches and sport scientists may be able to estimate force/torque production from individual muscles during multi-joint, dynamic constant external resistance muscle actions.

Optimization of an Optical Test Bench for Tire Properties Measurement and Tread Defects Characterization

PubMed Central

Castillo Aguilar, Juan Jesús; Cabrera Carrillo, Juan Antonio; Guerra Fernández, Antonio Jesús; Postigo Pozo, Sergio

2017-01-01

Tire characteristics and behavior are of great importance in vehicle dynamics since the forces transmitted in the tire-road contact are the main contributors to global vehicle performance. Several research groups have focused on the study and modeling of tires. Some of the most important factors that need to be known are tread characteristics and pressure distribution in the tire-ground contact patch. In this work, a test bench has been used to adequately determine the aforementioned factors. The measurement principle of the test bench is the frustration of total internal reflection (FTIR) of light. It makes use of a laterally illuminated glass on which the tire leans. An interposed plastic interface between them causes the reflection of light. Finally, a video camera captures the bright image formed through the glass. The brightness level in each pixel of the image is related to existing normal pressure. A study of the parameters that affect the test bench calibration such as type of interface material used, diffuse light, hysteresis, creep and transverse light absorption is performed. Experimental tests are conducted to relate tire inflation pressure and camber angle to the pressure distribution. Furthermore, the test bench is used to detect and evaluate the influence of defects in the tire on the contact pressures. PMID:28353674

Optimization of an Optical Test Bench for Tire Properties Measurement and Tread Defects Characterization.

PubMed

Castillo Aguilar, Juan Jesús; Cabrera Carrillo, Juan Antonio; Guerra Fernández, Antonio Jesús; Postigo Pozo, Sergio

2017-03-29

Tire characteristics and behavior are of great importance in vehicle dynamics since the forces transmitted in the tire-road contact are the main contributors to global vehicle performance. Several research groups have focused on the study and modeling of tires. Some of the most important factors that need to be known are tread characteristics and pressure distribution in the tire-ground contact patch. In this work, a test bench has been used to adequately determine the aforementioned factors. The measurement principle of the test bench is the frustration of total internal reflection (FTIR) of light. It makes use of a laterally illuminated glass on which the tire leans. An interposed plastic interface between them causes the reflection of light. Finally, a video camera captures the bright image formed through the glass. The brightness level in each pixel of the image is related to existing normal pressure. A study of the parameters that affect the test bench calibration such as type of interface material used, diffuse light, hysteresis, creep and transverse light absorption is performed. Experimental tests are conducted to relate tire inflation pressure and camber angle to the pressure distribution. Furthermore, the test bench is used to detect and evaluate the influence of defects in the tire on the contact pressures.

Fatigue effects upon sticking region and electromyography in a six-repetition maximum bench press.

PubMed

van den Tillaar, Roland; Saeterbakken, Atle Hole

2013-01-01

The aim of the study was to examine the sticking region and concomitant neuromuscular activation of the prime movers during six-repetition maximum (RM) bench pressing. We hypothesised that both peak velocities would decrease and that the electromyography (EMG) of the prime movers (deltoid, major pectoralis and triceps) would increase during the pre-sticking and sticking region during the six repetitions due to fatigue. Thirteen resistance-trained males (age 22.8 ± 2.2 years, stature 1.82 ± 0.06 m, body mass 83.4 ± 7.6 kg) performed 6-RM bench presses. Barbell kinematics and EMG activity of pectoralis major, deltoid anterior, and triceps brachii during the pre-, sticking and post-sticking region of each repetition in a 6-RM bench press were analysed. For both the sticking as the post-sticking region, the time increased significantly from the first to the sixth repetition. Vertical barbell height at the start of sticking region was lower, while the height at the end of the sticking region and post-sticking region did not change during the six repetitions. It was concluded that in 6-RM bench pressing performance, the sticking region is a poor mechanical force region due to the unchanged barbell height at the end of the sticking region. Furthermore, when fatigue occurs, the pectoralis and the deltoid muscles are responsible for surpassing the sticking region as indicated by their increased activity during the pre- and sticking region during the six-repetitions bench press.

Air pollution control system research: An iterative approach to developing affordable systems

NASA Technical Reports Server (NTRS)

Watt, Lewis C.; Cannon, Fred S.; Heinsohn, Robert J.; Spaeder, Timothy A.

1995-01-01

This paper describes a Strategic Environmental Research and Development Program (SERDP) funded project led jointly by the Marine Corps Multi-Commodity Maintenance Centers, and the Air and Energy Engineering Research Laboratory (AEERL) of the USEPA. The research focuses on paint booth exhaust minimization using recirculation, and on volatile organic compound (VOC) oxidation by the modules of a hybrid air pollution control system. The research team is applying bench, pilot and full scale systems to accomplish the goals of reduced cost and improved effectiveness of air treatment systems for paint booth exhaust.

The effects of grip width on sticking region in bench press.

PubMed

Gomo, Olav; Van Den Tillaar, Roland

2016-01-01

The aim of this study was to examine the occurrence of the sticking region by examining how three different grip widths affect the sticking region in powerlifters' bench press performance. It was hypothesised that the sticking region would occur at the same joint angle of the elbow and shoulder independent of grip width, indicating a poor mechanical region for vertical force production at these joint angles. Twelve male experienced powerlifters (age 27.7 ± 8.8 years, mass 91.9 ± 15.4 kg) were tested in one repetition maximum (1-RM) bench press with a narrow, medium and wide grip. Joint kinematics, timing, bar position and velocity were measured with a 3D motion capture system. All participants showed a clear sticking region with all three grip widths, but this sticking region was not found to occur at the same joint angles in all three grip widths, thereby rejecting the hypothesis that the sticking region would occur at the same joint angle of the elbow and shoulder independent of grip width. It is suggested that, due to the differences in moment arm of the barbell about the elbow joint in the sticking region, there still might be a poor mechanical region for total force production that is joint angle-specific.

HANDBOOK ON ADVANCED PHOTOCHEMICAL OXIDATION PROCESSES

EPA Science Inventory

This handbook summarizes commercial-scale system performance and cost data for advanced photochemical oxidation (APO) treatment of contaminated water, air, and solids. Similar information from pilot- and bench-scale evaluations of APO processes is also included to supplement the...

Control of air emissions from POTWs using biofiltration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Webster, T.S.; Devinny, J.S.; Torres, E.M.

1995-12-31

The University of Southern California (USC), in collaboration with the County Sanitation Districts of Orange County (CSDOC), the South Coast Air Quality Management District (SCAQMD), Southern California Edison (SCE), the Water Environment Research Foundation (WERF), and Huntingdon Environmental Engineering, Inc. (HEEI), is conducting a research project to evaluate the application of biofiltration to remove volatile organic compounds (VOCs), odor-causing air pollutants, and toxics from a publicly owned treatment works (POTW) waste airstream. As part of this project, bench-scale and pilot-scale experiments are being conducted to test the effectiveness of biofiltration and determine the optimum parameters for applying biofiltration to POTWs.more » Results from the bench-scale experiments demonstrate that biofiltration is effective in reducing the concentration of hydrogen sulfide (H{sub 2}S) and total VOCs present in waste airstreams by over 99% and up to 90%, respectively. Average reduction of specific aromatic and carbonyl compounds ranged from 55% to 91%. Removal efficiencies for chlorinated hydrocarbons were variable, ranging from 6% to 88%. Overall, biofiltration appears to be a promising technology for full-scale implementation at POTWs for VOC and odor emission compliance.« less

Functional Task Test: 3. Skeletal Muscle Performance Adaptations to Space Flight

NASA Technical Reports Server (NTRS)

Ryder, Jeffrey W.; Wickwire, P. J.; Buxton, R. E.; Bloomberg, J. J.; Ploutz-Snyder, L.

2011-01-01

The functional task test is a multi-disciplinary study investigating how space-flight induced changes to physiological systems impacts functional task performance. Impairment of neuromuscular function would be expected to negatively affect functional performance of crewmembers following exposure to microgravity. This presentation reports the results for muscle performance testing in crewmembers. Functional task performance will be presented in the abstract "Functional Task Test 1: sensory motor adaptations associated with postflight alternations in astronaut functional task performance." METHODS: Muscle performance measures were obtained in crewmembers before and after short-duration space flight aboard the Space Shuttle and long-duration International Space Station (ISS) missions. The battery of muscle performance tests included leg press and bench press measures of isometric force, isotonic power and total work. Knee extension was used for the measurement of central activation and maximal isometric force. Upper and lower body force steadiness control were measured on the bench press and knee extension machine, respectively. Tests were implemented 60 and 30 days before launch, on landing day (Shuttle crew only), and 6, 10 and 30 days after landing. Seven Space Shuttle crew and four ISS crew have completed the muscle performance testing to date. RESULTS: Preliminary results for Space Shuttle crew reveal significant reductions in the leg press performance metrics of maximal isometric force, power and total work on R+0 (p<0.05). Bench press total work was also significantly impaired, although maximal isometric force and power were not significantly affected. No changes were noted for measurements of central activation or force steadiness. Results for ISS crew were not analyzed due to the current small sample size. DISCUSSION: Significant reductions in lower body muscle performance metrics were observed in returning Shuttle crew and these adaptations are likely contributors to impaired functional tasks that are ambulatory in nature (See abstract Functional Task Test: 1). Interestingly, no significant changes in central activation capacity were detected. Therefore, impairments in muscle function in response to short-duration space flight are likely myocellular rather than neuromotor in nature.

Experimental study of air delivery into water-conveyance system of the radial-axial turbine

NASA Astrophysics Data System (ADS)

Maslennikova, Alexandra; Platonov, Dmitry; Minakov, Andrey; Dekterev, Dmitry

2017-10-01

The paper presents an experimental study of oscillatory response in the Francis turbine of hydraulic unit. The experiment was performed on large-scale hydrodynamic test-bench with impeller diameter of 0.3 m. The effect of air injection on the intensity of pressure pulsations was studied at the maximum pressure pulsations in the hydraulic unit. It was revealed that air delivery into the water-conveyance system of the turbine results in almost two-fold reduction of pressure pulsations.

Creating and sustaining a military women's Health Research Interest Group.

PubMed

Wilson, Candy; Trego, Lori; Rychnovsky, Jacqueline; Steele, Nancy; Foradori, Megan

2015-01-01

In 2008, four doctorate military nurse scientists representing the triservices (Army, Navy, and Air Force) identified a common interest in the health and care of all women in the armed forces. For 7 years, the team's shared vision to improve servicewomen's health inspired them to commit to a rigorous schedule of planning, developing, and implementing an innovative program that has the capability of advancing scientific knowledge and influencing health policy and practice through research. The ultimate goal of the Military Women's Health Research Interest Group (MWHRIG) is to support military clinicians and leaders in making evidence-based practice and policy decisions. They developed a 4-pronged approach to cultivate the science of military women's healthcare: evaluate the existing evidence, develop a research agenda that addresses gaps in knowledge, facilitate the collaboration of multidisciplinary research, and build the bench of future researchers. The MWHRIG has been a resource to key leaders; its value has been validated by multiservice and multidisciplinary consultations. However, the journey to goal attainment has only been achieved by the enduring commitment of these MWHRIG leaders and their passion to ensure the health and wellbeing of the many women who serve in the United States military. This article describes their journey of dedication.

HANDBOOK ON ADVANCED NONPHOTOCHEMICAL OXIDATION PROCESSES

EPA Science Inventory

The purpose of this handbook is to summarize commercial-scale system performance and cost data for advanced nonphotochemical oxidation (ANPO) treatment of contaminated water, air, and soil. Similar information from pilot-and bench-scale evaluations of ANPO processes is also inclu...

TREATMENT STUDIES OF CCL CONTAMINANTS

EPA Science Inventory

Bench-scale screening-level treatment data are presented for compounds listed in the Contaminant Candidate List (CCL). All of the CCl compounds are predicted to be economically removed by either activated carbon or air stripping technologies. To complete the screening-level treat...

Validation and Reliability of a Novel Test of Upper Body Isometric Strength.

PubMed

Bellar, David; Marcus, Lena; Judge, Lawrence W

2015-09-29

The purpose of the present investigation was to examine the association of a novel test of upper body isometric strength against a 1RM bench press measurement. Forty college age adults (n = 20 female, n = 20 male; age 22.8 ± 2.8 years; body height 171.6 ± 10.8 cm; body mass 73.5 ± 16.3 kg; body fat 23.1 ± 5.4%) volunteered for the present investigation. The participants reported to the lab on three occasions. The first visit included anthropometric measurements and familiarization with both the upper body isometric test and bench press exercise. The final visits were conducted in a randomized order, with one being a 1RM assessment on the bench press and the other consisting of three trials of the upper body isometric assessment. For the isometric test, participants were positioned in a "push-up" style position while tethered (stainless steel chain) to a load cell (high frequency) anchored to the ground. The peak isometric force was consistent across all three trials (ICC = 0.98) suggesting good reliability. Multiple regression analysis was completed with the predictors: peak isometric force, gender, against the outcome variable 1RM bench press. The analysis resulted in a significant model (r2 = 0.861, p≤0.001) with all predictor variables attaining significance in the model (p<0.05). Isometric peak strength had the greatest effect on the model (Beta = 5.19, p≤0.001). Results from this study suggest that the described isometric upper body strength assessment is likely a valid and reliable tool to determine strength. Further research is warranted to gather a larger pool of data in regard to this assessment.

Validation and Reliability of a Novel Test of Upper Body Isometric Strength

PubMed Central

Bellar, David; Marcus, Lena; Judge, Lawrence W.

2015-01-01

The purpose of the present investigation was to examine the association of a novel test of upper body isometric strength against a 1RM bench press measurement. Forty college age adults (n = 20 female, n = 20 male; age 22.8 ± 2.8 years; body height 171.6 ± 10.8 cm; body mass 73.5 ± 16.3 kg; body fat 23.1 ± 5.4%) volunteered for the present investigation. The participants reported to the lab on three occasions. The first visit included anthropometric measurements and familiarization with both the upper body isometric test and bench press exercise. The final visits were conducted in a randomized order, with one being a 1RM assessment on the bench press and the other consisting of three trials of the upper body isometric assessment. For the isometric test, participants were positioned in a “push-up” style position while tethered (stainless steel chain) to a load cell (high frequency) anchored to the ground. The peak isometric force was consistent across all three trials (ICC = 0.98) suggesting good reliability. Multiple regression analysis was completed with the predictors: peak isometric force, gender, against the outcome variable 1RM bench press. The analysis resulted in a significant model (r2 = 0.861, p≤0.001) with all predictor variables attaining significance in the model (p<0.05). Isometric peak strength had the greatest effect on the model (Beta = 5.19, p≤0.001). Results from this study suggest that the described isometric upper body strength assessment is likely a valid and reliable tool to determine strength. Further research is warranted to gather a larger pool of data in regard to this assessment. PMID:26557203

Smith machine counterbalance system affects measures of maximal bench press throw performance.

PubMed

Vingren, Jakob L; Buddhadev, Harsh H; Hill, David W

2011-07-01

Equipment with counterbalance weight systems is commonly used for the assessment of performance in explosive resistance exercise movements, but it is not known if such systems affect performance measures. The purpose of this study was to determine the effect of using a counterbalance weight system on measures of smith machine bench press throw performance. Ten men and 14 women (mean ± SD: age, 25 ± 4 years; height, 173 ± 10 cm; weight, 77.7 ± 18.3 kg) completed maximal smith machine bench press throws under 4 different conditions (2 × 2; counterbalance × load): with or without a counterbalance weight system and using 'light' or 'moderate' net barbell loads. Performance variables (peak force, peak velocity, and peak power) were measured using a linear accelerometer attached to the barbell. The counterbalance weight system resulted in significant (p < 0.001) reductions in measures of peak force (mean difference ± standard error: light: -112 ± 20 N; moderate: -140 ± 23 N), peak velocity (light: -0.49 ± 0.10 m·s; moderate: -0.33 ± 0.07 m·s), and peak power (light: -220 ± 43 W; moderate: -143 ± 28 W) compared with no counterbalance system for both load conditions. Load condition did not affect absolute or percentage reductions from the counterbalance weight system for any variable. In conclusion, the use of a counterbalance weight system reduces accelerometer-based performance measures for the bench press throw exercise at light and moderate loads. This reduction in measures is likely because of an increase in the external resistance during the movement, which results in a discrepancy between the manually input and the actual value for external load. A counterbalance weight system should not be used when measuring performance in explosive resistance exercises with an accelerometer.

Comparison of the Force-, Velocity- and Power-Time Curves Between the Concentric-Only and Eccentric-Concentric Bench Press Exercises.

PubMed

Pérez-Castilla, Alejandro; Comfort, Paul; McMahon, John J; Pestaña-Melero, Francisco Luis; García-Ramos, Amador

2018-01-17

The aim of this study was to compare the temporal and mechanical variables between the concentric-only and eccentric-concentric bench press (BP) variants. Twenty-one men (age: 22.0±4.2 years, body mass: 73.4±7.7 kg, height: 177.2±8.0 cm; one-repetition maximum [1RM]: 1.12±0.12 kg⋅kg) were evaluated during the concentric-only and eccentric-concentric BP variants using 80% 1RM. Temporal (concentric phase duration, propulsive phase duration, and time to reach the maximum values of force, velocity, and power) and mechanical variables (force, velocity, and power), determined using a linear velocity transducer, were compared between both BP variants. All temporal variables were significantly lower during the eccentric-concentric BP compared to the concentric-only BP (P < 0.05; effect size [ES] range: 0.80-2.52). Maximum force as well as the mean values of velocity and power were significantly higher for the eccentric-concentric BP compared to the concentric-only BP (all P < 0.001; ES range: 2.87-3.58). However, trivial to small differences between both BP variants were observed for mean force (ES: 0.00-0.36) as well as for maximum velocity (ES: 0.40) and power (ES: 0.41). The stretch-shortening cycle (i.e., eccentric-concentric BP) mainly enhanced force production at the early portion of the concentric phase, but this potentiation effect gradually reduced over the latter part of the movement. Finally, force was higher for the concentric-only BP during 49% of the concentric phase duration. These results suggest that both BP variants should be included during resistance training programs in order to optimize force output at different points of the concentric phase.

[Quantitative analysis of factors to influence the environment of the clean room and clean bench during preparation of intravenous hyperalimentation (IVH) admixtures].

PubMed

Hotoda, S; Aoyama, T; Sato, A; Yamamura, Y; Nakajima, K; Nakamura, K; Sato, H; Iga, T

1999-12-01

We quantitatively studied factors influencing the environment cleanliness for intravenous hyperalimentation (IVH) admixing. The environment cleanliness was evaluated by measuring the counts of particles (> 0.5 micron) and bacteria floating in 1 ft3 of the air inside the clean room (23.6 m3) and in the clean bench built in the department of pharmacy, The University of Tokyo Hospital in 1998. The number of particles at the center of the clean room during IVH admixing by 4 pharmacists was higher than that at the medicine passing area (150 +/- 50/ft3 vs. 260 +/- 60/ft3; mean +/- S.D., n = 12). The cleanliness inside the clean room was improved as the measurement point became higher from the floor (600 +/- 180/ft3, 150 +/- 50/ft3, and 35 +/- 15/ft3 at 50, 100, and 150 cm height, respectively) and the number of persons working inside the room decreased. The changes in the counts of floating bacteria were similar to that of floating particles under the same conditions. In addition the effect of disinfection on the counts of bacteria was clearly observed. When the cleanliness of the room became lower by turning off the air conditioning, the particle counts inside the clean bench became lower along with the distance from the front glass becoming deeper (i.e., 1400 +/- 550/ft3, 140 +/- 70/ft3, and 40 +/- 30/ft3 at 0, 5, and 15 cm, respectively). From these lines of evidence, the following items were suggested in order to maintain the environment cleanliness for IVH admixing. First, the number of persons residing in the clean room should be kept to be minimum. Second, the clean bench should be set up in the center of the clean room. Finally IVH admixing operation should be performed at more than 15 cm depth inside the front glass surface of the clean bench. Moreover, the effect of mopping-up of the clean room with 0.1% benzethonium chloride clearly demonstrated the importance of disinfection on a routine basis.

HANDBOOK ON ADVANCED PHOTOCHEMICAL OXIDATION ...

EPA Pesticide Factsheets

This handbook summarizes commercial-scale system performance and cost data for advanced photochemical oxidation (APO) treatment of contaminated water, air, and solids. Similar information from pilot- and bench-scale evaluations of APO processes is also included to supplement the commercial-scale data. Performance and cost data is summarized for various APO processes, including vacuum ultraviolet (VUV) photolysis, ultraviolet (UV)/oxidation, photo-Fenton, and dye- or semiconductor-sensitized APO processes. This handbook is intended to assist engineering practitioners in evaluating the applicability of APO processes and in selecting one or more such processes for site-specific evaluation.APO has been shown to be effective in treating contaminated water and air. Regarding contaminated water treatment, UV/oxidation has been evaluated for the most contaminants, while VUV photolysis has been evaluated for the fewest. Regarding contaminated air treatment, the sensitized APO processes have been evaluated for the most contaminants, while VUV photolysis has been evaluated for the fewest.APO processes for treating contaminated solids generally involve treatment of contaminated slurry or leachate generated using an extraction process such as soil washing. APO has been shown to be effective in treating contaminated solids, primarily at the bench-scale level. Information

Slipping and Tipping: Measuring Static Friction with a Straightedge

NASA Astrophysics Data System (ADS)

Dietz, Eric; Aguilar, Isaac

2012-11-01

Following a discussion of forces, torques, and the conditions for static equilibrium, I tell my introductory mechanics class that I will show them how to measure the coefficient of static friction, μs, between the surfaces of a block and the front bench using nothing but a straightedge. After a few seconds of hushed anticipation, I nudge the block in Fig. 1 (a) gently with the straightedge, applying a horizontal force F that gradually increases from zero to a value that either causes the object to slip (Fs) or to tip (Ft). Which of these happens first depends on μs, the depth D of the block, and on h, the height above the bench surface at which F is applied. Starting at the bottom of the block, it tends to slip before tipping, but there is a critical height hc above which the block tips before slipping. The value of hc at which this transition occurs is then used to produce a value of μs for these surfaces.

Performance and durability testing of parabolic trough receivers

NASA Astrophysics Data System (ADS)

Lei, Dongqiang; Fu, Xuqiang; Zhao, Dongming; Yuan, Guofeng; Wang, Zhifeng; Guo, Minghuan

2017-06-01

The paper describes the key performance and durability testing facilities of the parabolic trough receiver developed by Institute of Electrical Engineering, Chinese Academy of Sciences. The indoor heat loss test can be applied at 4-7 different temperature levels within 200-550 on receivers. The optical efficiency test bench consists of 12 metal halide lamps as the solar simulator and a 5 m length half-elliptical cylinder reflector with flat end reflectors. 3 ultra-precision temperature sensors are used in receiver each end to get the temperature difference. The residual gas analysis test bench is applied to analyze and predict the vacuum lifetime of the receiver. It can test the variations of composition and partial pressure of residual gases with temperature and time in the receiver annulus space by a high sensitivity quadrupole mass spectrometer gas analyzer. A coating accelerated ageing test bench, which is also used to test the thermal cycle, has been developed. This test bench uses the absorber tube of the recevier as the resistance heater to heat up the whole receiver. The coating lifetime can be predicted by the Arrhenius parameters. For the cycling test, the compressed air is used to directly cool the inner surface of the absorber tube. The thermal cycling test is performed with temperature cycles from 150 °C to 450 °C for 160 cycles. The maximum thermal cycling frequency is 8 cycles per day. The mechanical fatigue test bench is used to test the bellows and the glass-to-metal seals durability at the same time. Both bellows are expanded and compressed to 6.5 mm in turn with 10,000 cycles. A new rotating test bench was also developed to test the thermal efficiency of the receiver.

COMPUTER-AIDED DATA ACQUISITION FOR COMBUSTION EXPERIMENTS

EPA Science Inventory

The article describes the use of computer-aided data acquisition techniques to aid the research program of the Combustion Research Branch (CRB) of the U.S. EPA's Air and Energy Engineering Research Laboratory (AEERL) in Research Triangle Park, NC, in particular on CRB's bench-sca...

New projects developed by COMOTI in gas industry

NASA Astrophysics Data System (ADS)

Nitulescu, Marian; Silivestru, Valentin; Toma, Niculae; Slujitoru, Cristian; Petrescu, Valentin; Leahu, Mihai; Oniga, Ciprian; Ulici, Gheorghe

2015-08-01

The paper aims to present two new projects developed by the Romanian Research and Development Institute for Gas Turbines (COMOTI) in partnership with City University of London and GHH-Rand Germany, in the field of screw compressors/expanders. COMOTI passed, in recent years, from being a GHH-Rand licensed manufacturer for a range of oil-injected screw compressors, of CU type, to a new phase of range diversification, approaching screw compressors with a maximum discharge pressure of 45 bara. So, in cooperation with City University and GHH-Rand we design, manufacture and test, with air, in COMOTI test bench the new type of screw compressor named CHP 220. Also, the cooperation with GHH-Rand has resulted in the design, manufacture and air testing on the test bench, and then gas testing - in a gas compression station - for an electric generator driven by a screw expander. This paper presents how the tests were carried out, the experimental data and the interpretation of results

Greenhouse Gas Emissions from Three Cage Layer Housing Systems

PubMed Central

Fournel, Sébastien; Pelletier, Frédéric; Godbout, Stéphane; Lagacé, Robert; Feddes, John

2011-01-01

Simple Summary Greenhouse gas (GHG) emissions were measured from three different cage layer housing systems. A comparative study was conducted to identify the housing system with the least impact on the environment. The results showed that liquid manure from deep-pit housing systems produces greater emissions of carbon dioxide (CO2), methane (CH4) and nitrous oxide (N2O) than natural and forced dried manure from belt housing systems. The influencing factors appeared to be the manure removal frequency and the dry matter content of the manure. Abstract Agriculture accounts for 10 to 12% of the World’s total greenhouse gas (GHG) emissions. Manure management alone is responsible for 13% of GHG emissions from the agricultural sector. During the last decade, Québec’s egg production systems have shifted from deep-pit housing systems to manure belt housing systems. The objective of this study was to measure and compare carbon dioxide (CO2), methane (CH4) and nitrous oxide (N2O) emissions from three different cage layer housing systems: a deep liquid manure pit and a manure belt with natural or forced air drying. Deep liquid manure pit housing systems consist of “A” frame layer cages located over a closed pit containing the hens’ droppings to which water is added to facilitate removal by pumping. Manure belt techniques imply that manure drops on a belt beneath each row of battery cages where it is either dried naturally or by forced air until it is removed. The experiment was replicated with 360 hens reared into twelve independent bench-scale rooms during eight weeks (19–27 weeks of age). The natural and forced air manure belt systems reduced CO2 (28.2 and 28.7 kg yr−1 hen−1, respectively), CH4 (25.3 and 27.7 g yr−1 hen−1, respectively) and N2O (2.60 and 2.48 g yr−1 hen−1, respectively) emissions by about 21, 16 and 9% in comparison with the deep-pit technique (36.0 kg CO2 yr−1 hen−1, 31.6 g CH4 yr−1 hen−1 and 2.78 g N2O yr−1 hen−1). The shift to manure belt systems needs to be encouraged since this housing system significantly decreases the production of GHG. PMID:26486772

An ABS control logic based on wheel force measurement

NASA Astrophysics Data System (ADS)

Capra, D.; Galvagno, E.; Ondrak, V.; van Leeuwen, B.; Vigliani, A.

2012-12-01

The paper presents an anti-lock braking system (ABS) control logic based on the measurement of the longitudinal forces at the hub bearings. The availability of force information allows to design a logic that does not rely on the estimation of the tyre-road friction coefficient, since it continuously tries to exploit the maximum longitudinal tyre force. The logic is designed by means of computer simulation and then tested on a specific hardware in the loop test bench: the experimental results confirm that measured wheel force can lead to a significant improvement of the ABS performances in terms of stopping distance also in the presence of road with variable friction coefficient.

Stent longitudinal strength assessed using point compression: insights from a second-generation, clinically related bench test.

PubMed

Ormiston, John A; Webber, Bruce; Ubod, Ben; White, Jonathon; Webster, Mark W I

2014-02-01

Stent longitudinal distortion, while infrequent, can lead to adverse clinical events. Our first bench comparison of susceptibility of different stent designs to distortion applied force to the entire circumference of the proximal stent hoop. The test increased understanding of stent design and led to recommendations for design change in some. Our second-generation test more closely mimics clinical scenarios by applying force to a point on the proximal hoop of a malapposed stent. Each 3-mm-diameter stent was secured in a test apparatus so that its proximal 5 mm was malapposed in a 3.5-mm tube. An instron applied force to the proximal hoop of each of 5 examples of each of 6 stent designs using a narrow rod so that force applied and distance compressed could be measured. Hoops on the side of the force were pushed together, became malapposed, and obstructed the lumen. In addition, the proximal stent hoop tilted causing malapposition, the contralateral side of the stent from the applied force causing lumen obstruction. This second-generation, more clinically relevant test showed the Biomatrix Flex was the most resistant to deformation and the Element the most easily deformed. The addition of more connectors between the proximal hoops in the Promus Premier design has reduced the potential for distortion when compared with the Element, so that distortion was similar to the Vision, Multi-Link 8, and Integrity designs. The test also provided insight into the way in which stents are likely to distort in clinical practice.

Aeroservoelastic and Structural Dynamics Research on Smart Structures Conducted at NASA Langley Research Center

NASA Technical Reports Server (NTRS)

McGowan, Anna-Maria Rivas; Wilkie, W. Keats; Moses, Robert W.; Lake, Renee C.; Florance, Jennifer Pinkerton; Wieseman, Carol D.; Reaves, Mercedes C.; Taleghani, Barmac K.; Mirick, Paul H.; Wilbur, Mathew L.

1997-01-01

An overview of smart structures research currently underway at the NASA Langley Research Center in the areas of aeroservoelasticity and structural dynamics is presented. Analytical and experimental results, plans, potential technology pay-offs, and challenges are discussed. The goal of this research is to develop the enabling technologies to actively and passively control aircraft and rotorcraft vibration and loads using smart devices. These enabling technologies and related research efforts include developing experimentally-validated finite element and aeroservoelastic modeling techniques; conducting bench experimental tests to assess feasibility and understand system trade-offs; and conducting large-scale wind tunnel tests to demonstrate system performance. The key aeroservoelastic applications of this research include: active twist control of rotor blades using interdigitated electrode piezoelectric composites and active control of flutter, and gust and buffeting responses using discrete piezoelectric patches. In addition, NASA Langley is an active participant in the DARPA/Air Force Research Laboratory/NASA/Northrop Grumman Smart Wing program which is assessing aerodynamic performance benefits using smart materials.

Laboratory Buildings.

ERIC Educational Resources Information Center

Barnett, Jonathan

The need for flexibility in science research facilities is discussed, with emphasis on the effect of that need on the design of laboratories. The relationship of office space, bench space, and special equipment areas, and the location and distribution of piping and air conditioning, are considered particularly important. This building type study…

78 FR 27951 - Foreign-Trade Zone (FTZ) 75-Phoenix, Arizona; Notification of Proposed Production Activity...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-13

... systems; duct temperature limiters; air/oil heat exchangers; oil cooler fans; fuel filter assemblies... assemblies; filter extractors; de- coupler/disassembly wrenches; torque wrench adaptors; test benches; drills...; filter assemblies; oil filter install kits; cartridge screens; filter housings; trim balance weights...

Theory of Near-Field Scanning with a Probe Array

DTIC Science & Technology

2014-01-01

AIR FORCE RESEARCH LABORATORY SENSORS DIRECTORATE WRIGHT-PATTERSON AIR FORCE BASE, OH 45433-7320 AIR FORCE MATERIEL COMMAND...AFRL/RYMH) Sensors Directorate, Air Force Research Laboratory Wright-Patterson Air Force Base, OH 45433-7320 Air Force Materiel Command, United...S) AND ADDRESS(ES) 10. SPONSORING/MONITORING AGENCY ACRONYM(S) Air Force Research Laboratory Sensors Directorate Wright-Patterson Air Force Base

PSE Aysis of Crossflow Instability on HifIre-5B Flight Test

DTIC Science & Technology

2017-06-05

AIR FORCE RESEARCH LABORATORY AEROSPACE SYSTEMS DIRECTORATE WRIGHT-PATTERSON AIR FORCE BASE, OH 45433-7542 AIR FORCE MATERIEL COMMAND UNITED...Air Force Research Laboratory, Aerospace Systems Directorate Wright-Patterson Air Force Base, OH 45433-7542 Air Force Materiel Command, United...States Air Force 9. SPONSORING/MONITORING AGENCY NAME(S) AND ADDRESS(ES) 10. SPONSORING/MONITORING Air Force Research Laboratory Aerospace Systems

Tactile Sensing Reflexes for Advanced Prosthetic Hands

DTIC Science & Technology

2016-10-01

mos.) 100% • Design and build “mechanical egg ” test equipment (1-2 mos.) (Abandoned, alternate approach developed) • Develop experimental protocol...of a “mechanical egg ” or force measuring object was rejected in favor of this common cracker. Page 6 • A comprehensive bench top study was

ACTIVATION AND REACTIVITY OF NOVEL CALCIUM-BASED SORBENTS FOR DRY SO2 CONTROL IN BOILERS

EPA Science Inventory

Chemically modified calcium hydroxide (Ca(OH)2) sorbents developed in the U.S. Environmental Protection Agency's Air and Energy Engineering Research Laboratory (AEERL) for sulfur dioxide (SO2) control in utility boilers were tested in an electrically heated, bench-scale isotherma...

GENERATION AND SIMULATION OF METALLIC PARTICULATE AIR POLLUTANTS BY ELECTRIC ARC SPRAYING

EPA Science Inventory

The report gives results of efforts to provide a generated output with an appropriate mass and concentration of fresh, dry, fine metal oxide particles for bench or pilot scale fine particulate collection research and development work. The work involved two electric arc aerosol ge...

Environmental Assessment for Air Force Research Laboratory Space Vehicles Integrated Experiments Division Office Space at Kirtland Air Force Base, Albuquerque, New Mexico

DTIC Science & Technology

2005-06-01

AIR FORCE RESEARCH LABORATORY SPACE VEHICLES INTEGRATED EXPERMENTS DIVISION OFFICE SPACE AT KIRTLAND AIR FORCE ... Kirtland Air Force Base (KAFB). The office building would house the Air Force Research Laboratory Space Vehicles Integrated Experiments Division...ADDRESS(ES) Air Force Research Laboratory ,Space Vehicles Directorate,3550 Aberdeen Ave. SE, Kirtland

Three-dimensional Crack Depth Profile Assessment using Near-Field Surface Acoustic Wave Signal Response (Postprint)

DTIC Science & Technology

2012-02-01

release; distribution unlimited. See additional restrictions described on inside pages STINFO COPY AIR FORCE RESEARCH...LABORATORY MATERIALS AND MANUFACTURING DIRECTORATE WRIGHT-PATTERSON AIR FORCE BASE, OH 45433-7750 AIR FORCE MATERIEL COMMAND UNITED STATES AIR FORCE...AFRL/RXLP) Materials and Manufacturing Directorate, Air Force Research Laboratory Wright-Patterson Air Force Base, OH 45433-7750 Air Force

33 CFR 334.590 - Atlantic Ocean off Cape Canaveral, Fla.; Air Force missile testing area, Patrick Air Force Base...

Code of Federal Regulations, 2011 CFR

2011-07-01

..., Fla.; Air Force missile testing area, Patrick Air Force Base, Fla. 334.590 Section 334.590 Navigation... RESTRICTED AREA REGULATIONS § 334.590 Atlantic Ocean off Cape Canaveral, Fla.; Air Force missile testing area... during firing periods to be specified by the Commander, Air Force Missile Test Center, Patrick Air Force...

33 CFR 334.590 - Atlantic Ocean off Cape Canaveral, Fla.; Air Force missile testing area, Patrick Air Force Base...

Code of Federal Regulations, 2013 CFR

2013-07-01

..., Fla.; Air Force missile testing area, Patrick Air Force Base, Fla. 334.590 Section 334.590 Navigation... RESTRICTED AREA REGULATIONS § 334.590 Atlantic Ocean off Cape Canaveral, Fla.; Air Force missile testing area... during firing periods to be specified by the Commander, Air Force Missile Test Center, Patrick Air Force...

33 CFR 334.590 - Atlantic Ocean off Cape Canaveral, Fla.; Air Force missile testing area, Patrick Air Force Base...

Code of Federal Regulations, 2012 CFR

2012-07-01

..., Fla.; Air Force missile testing area, Patrick Air Force Base, Fla. 334.590 Section 334.590 Navigation... RESTRICTED AREA REGULATIONS § 334.590 Atlantic Ocean off Cape Canaveral, Fla.; Air Force missile testing area... during firing periods to be specified by the Commander, Air Force Missile Test Center, Patrick Air Force...

33 CFR 334.590 - Atlantic Ocean off Cape Canaveral, Fla.; Air Force missile testing area, Patrick Air Force Base...

Code of Federal Regulations, 2014 CFR

2014-07-01

..., Fla.; Air Force missile testing area, Patrick Air Force Base, Fla. 334.590 Section 334.590 Navigation... RESTRICTED AREA REGULATIONS § 334.590 Atlantic Ocean off Cape Canaveral, Fla.; Air Force missile testing area... during firing periods to be specified by the Commander, Air Force Missile Test Center, Patrick Air Force...

Quadrature transmit coil for breast imaging at 7 tesla using forced current excitation for improved homogeneity.

PubMed

McDougall, Mary Preston; Cheshkov, Sergey; Rispoli, Joseph; Malloy, Craig; Dimitrov, Ivan; Wright, Steven M

2014-11-01

To demonstrate the use of forced current excitation (FCE) to create homogeneous excitation of the breast at 7 tesla, insensitive to the effects of asymmetries in the electrical environment. FCE was implemented on two breast coils: one for quadrature (1) H imaging and one for proton-decoupled (13) C spectroscopy. Both were a Helmholtz-saddle combination, with the saddle tuned to 298 MHz for imaging and 75 MHz for spectroscopy. Bench measurements were acquired to demonstrate the ability to force equal currents on elements in the presence of asymmetric loading to improve homogeneity. Modeling and temperature measurements were conducted per safety protocol. B1 mapping, imaging, and proton-decoupled (13) C spectroscopy were demonstrated in vivo. Using FCE to ensure balanced currents on elements enabled straightforward tuning and maintaining of isolation between quadrature elements of the coil. Modeling and bench measurements confirmed homogeneity of the field, which resulted in images with excellent fat suppression and in broadband proton-decoupled carbon-13 spectra. FCE is a straightforward approach to ensure equal currents on multiple coil elements and a homogeneous excitation field, insensitive to the effects of asymmetries in the electrical environment. This enabled effective breast imaging and proton-decoupled carbon-13 spectroscopy at 7T. © 2014 Wiley Periodicals, Inc.

Inspector General, DoD, Oversight of the Air Force Audit Agency Audit of the FY 1996 Air Force Consolidated Financial Statements.

DTIC Science & Technology

1997-04-10

financial statements . We delegated the audit of the FY 1996 Air Force consolidated financial statements to the Air Force Audit Agency on May 17, 1996...This report provides our endorsement of the Air Force Audit Agency disclaimer of opinion on the Air Force consolidated financial statements for FY...1996, along with the Air Force Audit Agency Report of Audit, ’Opinion on Fiscal Year 1996 Air Force Consolidated Financial Statements .’

Integral Design Methodology of Photocatalytic Reactors for Air Pollution Remediation.

PubMed

Passalía, Claudio; Alfano, Orlando M; Brandi, Rodolfo J

2017-06-07

An integral reactor design methodology was developed to address the optimal design of photocatalytic wall reactors to be used in air pollution control. For a target pollutant to be eliminated from an air stream, the proposed methodology is initiated with a mechanistic derived reaction rate. The determination of intrinsic kinetic parameters is associated with the use of a simple geometry laboratory scale reactor, operation under kinetic control and a uniform incident radiation flux, which allows computing the local superficial rate of photon absorption. Thus, a simple model can describe the mass balance and a solution may be obtained. The kinetic parameters may be estimated by the combination of the mathematical model and the experimental results. The validated intrinsic kinetics obtained may be directly used in the scaling-up of any reactor configuration and size. The bench scale reactor may require the use of complex computational software to obtain the fields of velocity, radiation absorption and species concentration. The complete methodology was successfully applied to the elimination of airborne formaldehyde. The kinetic parameters were determined in a flat plate reactor, whilst a bench scale corrugated wall reactor was used to illustrate the scaling-up methodology. In addition, an optimal folding angle of the corrugated reactor was found using computational fluid dynamics tools.

Selective effects of different fatigue protocols on the function of upper body muscles assessed through the force-velocity relationship.

PubMed

García-Ramos, Amador; Torrejón, Alejandro; Feriche, Belén; Morales-Artacho, Antonio J; Pérez-Castilla, Alejandro; Padial, Paulino; Jaric, Slobodan

2018-02-01

This study explored the feasibility of the force-velocity relationship (F-V) to detect the acute effects of different fatigue protocols on the selective changes of the maximal capacities of upper body muscles to produce force, velocity, and power. After determining the bench press one-repetition maximum (1RM), participants' F-V relationships were assessed during the bench press throw exercise on five separate sessions after performing one of the following fatiguing protocols: 60%1RM failure, 60%1RM non-failure, 80%1RM failure, 80%1RM non-failure, and no-fatigue. In the non-failure protocols, participants performed half the maximum number of repetitions than in their respective failure protocols. The main findings revealed that (1) all F-V relationships were highly linear (median r = 0.997 and r = 0.982 for averaged across participants and individual data, respectively), (2) the fatiguing protocols were ranked based on the magnitude of power loss as follows: 60%1RM failure > 80%1RM failure > 60%1RM non-failure > 80%1RM non-failure, while (3) the assessed maximum force and velocity outputs showed a particularly prominent reduction in the protocols based on the lowest and highest levels of fatigue (i.e., 80%1RM non-failure and 60%1RM failure), respectively. The results support the use of F-V to assess the effects of fatigue on the distinctive capacities of the muscles to produce force, velocity, and power output while performing multi-joint tasks, while the assessed maximum force and velocity capacities showed a particularly prominent reduction in the protocols based on the lowest and highest levels of fatigue (i.e., 80%1RM non-failure and 60%1RM failure), respectively.

Survival Analysis of US Air Force Officer Retention Rate

DTIC Science & Technology

2017-03-23

Air Force Institute of Technology AFIT Scholar Theses and Dissertations 3-23-2017 Survival Analysis of US Air Force Officer Retention Rate Courtney N...AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY Wright-Patterson Air Force Base, Ohio DISTRIBUTION STATEMENT A. APPROVED FOR PUBLIC RELEASE...to the Faculty Department of Operational Sciences Graduate School of Engineering and Management Air Force Institute of Technology Air University

75 FR 32750 - US Air Force Scientific Advisory Board Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-09

... DEPARTMENT OF DEFENSE Department of the Air Force US Air Force Scientific Advisory Board Notice of Meeting AGENCY: Department of the Air Force, US Air Force Scientific Advisory Board. ACTION: Meeting....150, the Department of Defense announces that the United States Air Force Scientific Advisory Board...

The Effects of Ballistic and Non-Ballistic Bench Press on Mechanical Variables.

PubMed

Moir, Gavin L; Munford, Shawn N; Moroski, Lindsey L; Davis, Shala E

2017-02-21

To investigate the effects of ballistic and non-ballistic bench press performed with loads equivalent to 30 and 90% 1-repetition maximum (1-RM) on mechanical variables. Eleven resistance-trained men (age: 23.0 ± 1.4 years; mass: 98.4 ± 14.4 kg) attended four testing sessions where they performed one of the following sessions: 1) three sets of five non-ballistic repetitions performed with a load equivalent to 30% 1-RM (30N-B), 2) three sets of five ballistic repetitions performed with a load equivalent to 30% 1-RM (30B), 3) three sets of four non-ballistic repetitions with a load equivalent to 90% 1-RM (90N-B), 4) three sets of four ballistic repetitions with a load equivalent to 90% 1-RM (90B). Force plates and a 3-D motion analysis system were used to determine the velocity, force, power output (PO) and work during each repetition. The heavier loads resulted in significantly greater forces applied to the barbell (mean differences: 472-783 N, p<0.001), but lower barbell velocities (mean differences: 0.85-1.20 m/s, p<0.001) and PO (mean differences: 118-492 W, p≤0.022). The ballistic conditions enhanced the mechanical variables only at the lower load with 30B producing significantly greater force (mean difference: 263 N, p<0.001), velocity (mean difference: 0.33 m/s, p<0.001), and PO (mean difference: 335 W, p<0.001) compared to 30N-B. Furthermore, the increase in PO across the 3 sets in 30B was significantly different from all other conditions (p=0.013). The total mechanical work performed was significantly greater for the conditions with the heavier loads compared to those with the lighter loads (mean differences: 3,62-5,600 J, p<0.001) and that performed during the ballistic conditions was significantly greater than that performed during the non-ballistic conditions with the same load (mean differences: 945-1,030 J, p<0.001). Ballistic bench press may be an effective exercise for developing power output and multiple sets may elicit post-activation potentiation that enhances force production. However, these benefits may be negated at heavier loads.

SITE EMERGING TECHNOLOGY SUMMARY: INTEGRATION OF PHOTOCATALYTIC OXIDATION WITH AIR STRIPPING OF CONTAMINATED AQUIFERS

EPA Science Inventory

In a recently completed test program, bench-scale laboratory studies at Arizona State University (ASU) in Tempe, AZ, and pilot-scale studies in a simulated field test situation at Zentox Corp in Ocala, FL, were performed to evaluate the integration of gas-solid ultraviolet (UV) p...

Air Force Research Laboratory’s Focused Long Term Challenges

DTIC Science & Technology

2008-04-01

Air Force Research Laboratory ( AFRL ) mission is to provide support to the Air Force (AF) and the warfighters with... Air Force Research Laboratory’s Focused Long Term Challenges Leo J Rose Munitions Directorate, Air Force Research Laboratory , 101 W Eglin Blvd...This technology vision, which was born in our Air Force Research Laboratory , builds on the Air Force’s traditional kill

Best Practices in User Needs/Requirements Generation

DTIC Science & Technology

2000-06-15

to the US Air Force, the framework was tested . All of the organizations demonstrated the existence of the four fundamental activities contained in...SP Air Force Deputy Chief of Staff for Security Police AF/TE Air Force Deputy Chief of Staff for Test and Evaluations AF/XO Air Force Deputy Chief of...Operational Test and Evaluation Center AFPD Air Force Policy Directive AFROC Air Force Requirements Oversight Council AFSOC Air Force Special Operations

75 FR 53863 - Amendment of Restricted Area R-5113; Socorro, NM

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-02

... using agency of Restricted Area R- 5113, Socorro, NM, to ``U.S. Air Force, Air Force Research Laboratory....S. Air Force, Air Force Research Laboratory.'' This change is required to reflect the change in the... words ``Using Agency. U.S. Air Force, Air Force Research Laboratory.'' Issued in Washington, DC, on...

Air Force Research Laboratory Preparation for Year 2000.

DTIC Science & Technology

1998-10-05

Air Force Research Laboratory , Phillips Research Site , Kirkland Air Force Base, New...Pentagon, Washington, D.C. 20301-1900. The identity of each writer and caller is fully protected. Acronym AFRL Air Force Research Laboratory INSPECTOR...completion of the implementation phase was May 31, 1999. Air Force Research Laboratory . The Air Force Research

United States Air Force Summer Research Program -- 1993. Volume 3. Phillips Laboratory

DTIC Science & Technology

1993-12-01

PHILLIPS LABORATORY KIRTLAND AIR FORCE BASE, NEW MEXICO SPONSORED BY: AIR FORCE OFFICE OF SCIENTIFIC RESEARCH ROLLING AIR FORCE BASE, WASHINGTON ,D.C...Report for. Summer Faculty Research Program at Phillips Laboratory Kirtland Air Force Base Sponsored by: Air Force Offlce of Scientific Research ...Prcgram Phillips Laboratory Kirtland

78 FR 49484 - Exchange of Air Force Real Property for Non-Air Force Real Property

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-14

... DEPARTMENT OF DEFENSE Department of Air Force Exchange of Air Force Real Property for Non-Air Force Real Property SUMMARY: Notice identifies excess Federal real property under administrative jurisdiction of the United States Air Force it intends to exchange for real property not currently owned by the...

76 FR 28215 - U.S. Air Force Scientific Advisory Board Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-05-16

... DEPARTMENT OF DEFENSE Department of the Air Force U.S. Air Force Scientific Advisory Board Notice of Meeting AGENCY: Department of the Air Force, U.S. Air Force Scientific Advisory Board, DoD. ACTION... 102-3.150, the Department of Defense announces that the United States Air Force Scientific Advisory...

76 FR 65187 - U.S. Air Force Scientific Advisory Board Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-20

... DEPARTMENT OF DEFENSE Department of the Air Force U.S. Air Force Scientific Advisory Board Notice of Meeting AGENCY: US Air Force Scientific Advisory Board, Department of the Air Force, DoD. ACTION: Meeting Cancellation Notice. SUMMARY: Due to difficulties, beyond the control of the U.S. Air Force...

76 FR 18537 - U.S. Air Force Scientific Advisory Board; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-04

... DEPARTMENT OF DEFENSE Department of the Air Force U.S. Air Force Scientific Advisory Board; Notice of Meeting AGENCY: Department of the Air Force, US Air Force Scientific Advisory Board. ACTION... 102-3.150, the Department of Defense announces that the United States Air Force Scientific Advisory...

76 FR 22083 - U.S. Air Force Academy Board of Visitors Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-20

...'t Tell'' way ahead; an Air Force perspective on Diversity; an Ethics briefing; and Air Force Academy... DEPARTMENT OF DEFENSE Department of the Air Force U.S. Air Force Academy Board of Visitors Notice of Meeting AGENCY: U.S. Air Force Academy Board of Visitors. ACTION: Meeting notice. SUMMARY...

76 FR 71333 - U.S. Air Force Academy Board of Visitors Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-17

... Don't Tell;'' a National and Air Force perspective on Diversity; the Air Force Academy Athletic... DEPARTMENT OF DEFENSE Department of the Air Force U.S. Air Force Academy Board of Visitors Notice of Meeting AGENCY: U.S. Air Force Academy Board of Visitors. ACTION: Meeting notice. SUMMARY: In...

Selenium Speciation and Management in Wet FGD Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Searcy, K; Richardson, M; Blythe, G

2012-02-29

This report discusses results from bench- and pilot-scale simulation tests conducted to determine the factors that impact selenium speciation and phase partitioning in wet FGD systems. The selenium chemistry in wet FGD systems is highly complex and not completely understood, thus extrapolation and scale-up of these results may be uncertain. Control of operating parameters and application of scrubber additives have successfully demonstrated the avoidance or decrease of selenite oxidation at the bench and pilot scale. Ongoing efforts to improve sample handling methods for selenium speciation measurements are also discussed. Bench-scale scrubber tests explored the impacts of oxidation air rate, tracemore » metals, scrubber additives, and natural limestone on selenium speciation in synthetic and field-generated full-scale FGD liquors. The presence and concentration of redox-active chemical species as well as the oxidation air rate contribute to the oxidation-reduction potential (ORP) conditions in FGD scrubbers. Selenite oxidation to the undesirable selenate form increases with increasing ORP conditions, and decreases with decreasing ORP conditions. Solid-phase manganese [Mn(IV)] appeared to be the significant metal impacting the oxidation of selenite to selenate. Scrubber additives were tested for their ability to inhibit selenite oxidation. Although dibasic acid and other scrubber additives showed promise in early clear liquor (sodium based and without calcium solids) bench-scale tests, these additives did not show strong inhibition of selenite oxidation in tests with higher manganese concentrations and with slurries from full-scale wet FGD systems. In bench-tests with field liquors, addition of ferric chloride at a 250:1 iron-to-selenium mass ratio sorbed all incoming selenite to the solid phase, although addition of ferric salts had no impact on native selenate that already existed in the field slurry liquor sample. As ORP increases, selenite may oxidize to selenate more rapidly than it sorbs to ferric solids. Though it was not possible to demonstrate a decrease in selenium concentrations to levels below the project'ale testing were evident at the pilot scale. Specifically, reducing oxidation air rate and ORP tends to either retain selenium as selenite in the liquor or shift selenium phase partitioning to the solid phase. Oxidation air flow rate control may be one option for managing selenium behavior in FGD scrubbers. Units that cycle load widely may find it more difficult to impact ORP conditions with oxidation air flow rate control alone. Because decreasing oxidation air rates to the reaction tank showed that all new selenium reported to the solids, the addition of ferric chloride to the pilot scrubber could not show further improvements in selenium behavior. Ferric chloride addition did shift mercury to the slurry solids, specifically to the fine particles. Several competing pathways may govern the reporting of selenium to the slurry solids: co-precipitation with gypsum into the bulk solids and sorption or co-precipitation with iron into the fine particles. Simultaneous measurement of selenium and mercury behavior suggests a holistic management strategy is best to optimize the fate of both of these elements in FGD waters. Work conducted under this project evaluated sample handling and analytical methods for selenium speciation in FGD waters. Three analytical techniques and several preservation methods were employed. Measurements of selenium speciation over time indicated that for accurate selenium speciation, it is best to conduct measurements on unpreserved, filtered samples as soon after sampling as possible. The capital and operating costs for two selenium management strategies were considered: ferric chloride addition and oxidation air flow rate control. For ferric chloride addition, as might be expected the reagent makeup costs dominate the overall costs, and range from 0.22 to 0.29 mills/kWh. For oxidation air flow rate control, a cursory comparison of capital costs and turndown capabilities for multi-stage and single-stage centrifugal blowers and several flow control methods was completed. For greenfield systems, changing the selection of blower type and flow control method may have payback periods of 4 to 5 years or more if based on energy savings alone. However, the benefits to managing redox chemistry in the scrubber could far outweigh the savings in electricity costs under some circumstances.« less

Experimental study of condensate subcooling with the use of a model of an air-cooled condenser

NASA Astrophysics Data System (ADS)

Sukhanov, V. A.; Bezukhov, A. P.; Bogov, I. A.; Dontsov, N. Y.; Volkovitsky, I. D.; Tolmachev, V. V.

2016-01-01

Water-supply deficit is now felt in many regions of the world. This hampers the construction of new steam-turbine and combined steam-and-gas thermal power plants. The use of dry cooling systems and, specifically, steam-turbine air-cooled condensers (ACCs) expands the choice of sites for the construction of such power plants. The significance of condensate subcooling Δ t as a parameter that negatively affects the engineering and economic performance of steam-turbine plants is thereby increased. The operation and design factors that influence the condensate subcooling in ACCs are revealed, and the research objective is, thus, formulated properly. The indicated research was conducted through physical modeling with the use of the Steam-Turbine Air-Cooled Condenser Unit specialized, multipurpose, laboratory bench. The design and the combined schematic and measurement diagram of this test bench are discussed. The experimental results are presented in the form of graphic dependences of the condensate subcooling value on cooling ratio m and relative weight content ɛ' of air in steam at the ACC inlet at different temperatures of cooling air t ca ' . The typical ranges of condensate subcooling variation (4 ≤ Δ t ≤ 6°C, 2 ≤ Δ t ≤ 4°C, and 0 ≤ Δ t ≤ 2°C) are identified based on the results of analysis of the attained Δ t levels in the ACC and numerous Δ t reduction estimates. The corresponding ranges of cooling ratio variation at different temperatures of cooling air at the ACC inlet are specified. The guidelines for choosing the adjusted ranges of cooling ratio variation with account of the results of experimental studies of the dependences of the absolute pressure of the steam-air mixture in the top header of the ACC and the heat flux density on the cooling ratio at different temperatures of cooling air at the ACC inlet are given.

CPAP Devices for Emergency Prehospital Use: A Bench Study.

PubMed

Brusasco, Claudia; Corradi, Francesco; De Ferrari, Alessandra; Ball, Lorenzo; Kacmarek, Robert M; Pelosi, Paolo

2015-12-01

CPAP is frequently used in prehospital and emergency settings. An air-flow output minimum of 60 L/min and a constant positive pressure are 2 important features for a successful CPAP device. Unlike hospital CPAP devices, which require electricity, CPAP devices for ambulance use need only an oxygen source to function. The aim of the study was to evaluate and compare on a bench model the performance of 3 orofacial mask devices (Ventumask, EasyVent, and Boussignac CPAP system) and 2 helmets (Ventukit and EVE Coulisse) used to apply CPAP in the prehospital setting. A static test evaluated air-flow output, positive pressure applied, and FIO2 delivered by each device. A dynamic test assessed airway pressure stability during simulated ventilation. Efficiency of devices was compared based on oxygen flow needed to generate a minimum air flow of 60 L/min at each CPAP setting. The EasyVent and EVE Coulisse devices delivered significantly higher mean air-flow outputs compared with the Ventumask and Ventukit under all CPAP conditions tested. The Boussignac CPAP system never reached an air-flow output of 60 L/min. The EasyVent had significantly lower pressure excursion than the Ventumask at all CPAP levels, and the EVE Coulisse had lower pressure excursion than the Ventukit at 5, 15, and 20 cm H2O, whereas at 10 cm H2O, no significant difference was observed between the 2 devices. Estimated oxygen consumption was lower for the EasyVent and EVE Coulisse compared with the Ventumask and Ventukit. Air-flow output, pressure applied, FIO2 delivered, device oxygen consumption, and ability to maintain air flow at 60 L/min differed significantly among the CPAP devices tested. Only the EasyVent and EVE Coulisse achieved the required minimum level of air-flow output needed to ensure an effective therapy under all CPAP conditions. Copyright © 2015 by Daedalus Enterprises.

Rinne revisited: steel versus aluminum tuning forks.

PubMed

MacKechnie, Cheryl A; Greenberg, Jesse J; Gerkin, Richard C; McCall, Andrew A; Hirsch, Barry E; Durrant, John D; Raz, Yael

2013-12-01

(1) Determine whether tuning fork material (aluminum vs stainless steel) affects Rinne testing in the clinical assessment of conductive hearing loss (CHL). (2) Determine the relative acoustic and mechanical outputs of 512-Hz tuning forks made of aluminum and stainless steel. Prospective, observational. Outpatient otology clinic. Fifty subjects presenting May 2011 to May 2012 with negative or equivocal Rinne in at least 1 ear and same-day audiometry. Rinne test results using aluminum and steel forks were compared and correlated with the audiometric air-bone gap. Bench top measurements using sound-level meter, microphone, and artificial mastoid. Patients with CHL were more likely to produce a negative Rinne test with a steel fork than with an aluminum fork. Logistic regression revealed that the probability of a negative Rinne reached 50% at a 19 dB air-bone gap for stainless steel versus 27 dB with aluminum. Bench top testing revealed that steel forks demonstrate, in effect, more comparable air and bone conduction efficiencies while aluminum forks have relatively lower bone conduction efficiency. We have found that steel tuning forks can detect a lesser air-bone gap compared to aluminum tuning forks. This is substantiated by observations of clear differences in the relative acoustic versus mechanical outputs of steel and aluminum forks, reflecting underlying inevitable differences in acoustic versus mechanical impedances of these devices, and thus efficiency of coupling sound/vibratory energy to the auditory system. These findings have clinical implications for using tuning forks to determine candidacy for stapes surgery.

Environmental Assessment, Balloon Launch and Landing Operations, Air Force Research Laboratory, Space Vehicles Directorate, Kirtland Air Force Base, New Mexico

DTIC Science & Technology

2012-06-01

Force Research Laboratory , Space Vehicles Directorate ( AFRL /RV) located at Kirtland Air Force Base is preparing an Environmental Assessment (EA) for...United States Air Force Research Laboratory , Space Vehicles Directorate ( AFRL /RV) located at Kirtland Air Force Base is preparing an Environmental...United States Air Force Research Laboratory , Space Vehicles Directorate ( AFRL

33 CFR 334.710 - The Narrows and Gulf of Mexico adjacent to Santa Rosa Island, Air Force Proving Ground Command...

Code of Federal Regulations, 2011 CFR

2011-07-01

... adjacent to Santa Rosa Island, Air Force Proving Ground Command, Eglin Air Force Base, Fla. 334.710 Section... Santa Rosa Island, Air Force Proving Ground Command, Eglin Air Force Base, Fla. (a) The restricted area... regulations in this section shall be enforced by the Commander, Air Force Proving Ground Command, Eglin Air...

77 FR 22770 - U.S. Air Force Scientific Advisory Board; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-17

... extended use of Air Force Space Command space-based sensors. In accordance with 5 U.S.C. 552b, as amended... DEPARTMENT OF DEFENSE Department of the Air Force U.S. Air Force Scientific Advisory Board; Notice of Meeting AGENCY: Department of the Air Force, U.S. Air Force Scientific Advisory Board. ACTION...

Air Force Medical Service > Resources > Suicide Prevention

Science.gov Websites

Air Force Medical Service Air Force Medical Service Join the Air Force Home Your Healthcare Healthy Videos MHS Genesis AFMS Priorities Trusted Care Vision Air Force Medical Home Full Spectrum Medical ) Air Force EFMP Who is an EFM? Who must enroll? EFMP-Medical EFMP-M Objectives Family Criteria EFMP-M

A Prototype JFACC: General George C. Kenney

DTIC Science & Technology

1994-06-01

Corps, as well as air forces from Australia and New Zealand . Many accounts of the Battles for Leyte and Luzon center around ground and naval forces...St Clair Streett USA Royal New Zealand Air Force (RNZAF) Royal Australian Air Force (RAAF) Air Command Organization SWPA June 15, 1944 Figure 5...Ground Task Force OPCON Operational Command POA Pacific Ocean Areas RAAF Royal Australian Air Force RNZAF Royal New Zealand Air Force SAP

Inspector General, DOD, Oversight of the Air Force Audit Agency Audit of the FY 1995 Air Force Consolidated Financial Statements.

DTIC Science & Technology

1996-04-18

financial statements . We delegated the audit of the FY 1995 Air Force consolidated financial statements to the Air Force Audit Agency. On March 1...1996, the Air Force Audit Agency issued its "Report of Audit: Opinion on Fiscal Year 1995 Air Force Consolidated Financial Statements " (Project 94053001...disclaimer of opinion. The audit objective was to determine the accuracy and completeness of the audit of the FY 1995 Air Force consolidated financial statements conducted

The effects of superset configuration on kinetic, kinematic, and perceived exertion in the barbell bench press.

PubMed

Weakley, Jonathon Js; Till, Kevin; Read, Dale B; Phibbs, Padraic J; Roe, Gregory; Darrall-Jones, Joshua; Jones, Ben L

2017-08-04

Training that is efficient and effective is of great importance to an athlete. One method of improving efficiency is by incorporating supersets into resistance training routines. However, the structuring of supersets is still unexplored. Therefore, the purpose of this study was to assess the effects of agonist-antagonist (A-A), alternate peripheral (A-P), and similar biomechanical (SB) superset configurations on rate of perceived exertion (RPE), kinetic and kinematic changes during the bench press. 10 subjects performed resistance training protocols in a randomized-crossover design, with magnitude-based inferences assessing changes/differences within and between protocols. Changes in RPE were very likely and almost certainly greater in the A-P and SB protocols when compared with the A-A, while all superset protocols had very likely to almost certain reductions in mean velocity and power from baseline. Reductions in mean velocity and power were almost certainly greater in the SB protocol, with differences between the A-A and A-P protocols being unclear. Decreases in peak force were likely and almost certain in the A-A and SB protocols respectively, with changes in A-P being unclear. Differences between these protocols showed likely greater decreases in SB peak forces when compared to A-A, with all other superset comparisons being unclear. This study demonstrates the importance of exercise selection when incorporating supersets into a training routine. It is suggested that the practitioner uses A-A supersets when aiming to improve training efficiency and minimize reductions in kinetic and kinematic output of the agonist musculature while completing the barbell bench press.

Beta-glucan production by Botryosphaeria rhodina in different bench-top bioreactors.

PubMed

Selbmann, L; Crognale, S; Petruccioli, M

2004-01-01

Evaluation of the technical feasibility of transferring beta-glucan production by Botryosphaeria rhodina DABAC-P82 from shaken flasks to bench-top bioreactors. Three different bioreactors were used: 3 l stirred tank reactor (STR-1) equipped with two different six-blade turbines; STR as above but equipped with a three-blade marine propeller plus draft-tube (STR-2); 2 l air-lift column reactor (ALR) equipped with an external loop. STR-1, tested at three different stirrer speeds (300, 500 and 700 rev min(-1)) appeared to be less suitable for beta-glucan production by the fungus, being maximum production (19.4 g l(-1)), productivity (0.42 g l(-1) h(-1)) and yield (0.48 g g(-1) of glucose consumed) markedly lower than those obtained in shaken culture (29.7 g l(-1), 1.23 g l(-1) h(-1) and 0.61 g g(-1), respectively). Better performances were obtained with both STR-2 and ALR. With the latter, in particular, the increase of production was accompanied by reduced fermentation time (25.7 g l(-1) after only 22 h); productivity and yield were highest (1.17 g l(-1) h(-1) and 0.62 g g(-1) of glucose consumed, respectively). Using an air-lift reactor with external loop, the scaling up from shaken flasks to bench-top bioreactor of the beta-glucan production by B. rhodina DABAC-P82 is technically feasible. Although culture conditions are still to be optimized, the results obtained using the ARL are highly promising.

76 FR 54742 - Privacy Act of 1974; System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-02

... phone at 703- 696-6488. SUPPLEMENTARY INFORMATION: The Department of the Air Force's notices for systems... individuals covered by the system: Air Force government civilians, vendors doing business with the U.S. Air Force, Air Force active duty military personnel, Air Force reserve personnel, and Air National Guard...

Advanced Thermal Batteries.

DTIC Science & Technology

1981-06-01

ADVANCED THERMAL BATTERIES NATIONAL UNION ELECTRIC CORPORATION ADVANCE SCIENCE DIVISION 1201 E. BELL STREET BLXXMINGTON, ILLINOIS 61701 JUNE 1981...December 1978 in: " Advanced Thermal Batteries " AFAPL-TR-78-114 Air Force Aero Propulsion Laboratory Air Force Wright Aeronautical Laboratories Air Force...March 1980 in: " Advanced Thermal Batteries " AFAPL-TR-80-2017 Air Force Aero Propulsion Laboratory Air Force Wright Aeronautical Laboratories Air Force

Air Force Office of Scientific Research 1991 Research Highlights

DTIC Science & Technology

1991-01-01

research at Air Force Europe, allied victory in the Persian Gulf con- programs totaling nearly $300 million annual- laboratories . Air Force ...transitioning nological environment? laboratories and research centers into four research accomplishments for Air Force use. In this added role as... Air Force’s saries; maintaining a strong research Organizationally, AFOSR has also glo ehran gol per infrastructure among Air Force

AFWL Standards for Scientific and Technical Reports.

DTIC Science & Technology

1980-04-01

Air Force Weapons Laboratory , Kirtland Air Force Base, New Mexico, under...PROGRAM ELEMEN T PROJECT TASK AREA & WORK UNIT NUMBERS Air Force Weapons Laboratory (SUR) Kirtland Air Force Base, NM 87117 62601F/99930000 I. CONTROLLING...OFFICE NAME AND ADDRESS 12 REPORT DATE Air Force Weapons Laboratory (SUR) April 1980 Kirtland Air Force Base, NM 87117 13. NUMBER OF PAGES 72

33 CFR 334.590 - Atlantic Ocean off Cape Canaveral, Fla.; Air Force missile testing area, Patrick Air Force Base...

Code of Federal Regulations, 2010 CFR

2010-07-01

..., Fla.; Air Force missile testing area, Patrick Air Force Base, Fla. 334.590 Section 334.590 Navigation... RESTRICTED AREA REGULATIONS § 334.590 Atlantic Ocean off Cape Canaveral, Fla.; Air Force missile testing area, Patrick Air Force Base, Fla. (a) The danger zone. An area in the Atlantic Ocean immediately offshore from...

33 CFR 334.630 - Tampa Bay south of MacDill Air Force Base, Fla.; small-arms firing range and aircraft jettison, U...

Code of Federal Regulations, 2010 CFR

2010-07-01

... Force Base, Fla.; small-arms firing range and aircraft jettison, U.S. Air Force, MacDill Air Force Base... Force Base, Fla.; small-arms firing range and aircraft jettison, U.S. Air Force, MacDill Air Force Base...″, longitude 82°33′02.44″; and thence to a point on the shore line of MacDill Air Force Base at latitude 27°50...

33 CFR 334.1280 - Bristol Bay, Alaska; air-to-air weapon range, Alaskan Air Command, U.S. Air Force.

Code of Federal Regulations, 2012 CFR

2012-07-01

... weapon range, Alaskan Air Command, U.S. Air Force. 334.1280 Section 334.1280 Navigation and Navigable... REGULATIONS § 334.1280 Bristol Bay, Alaska; air-to-air weapon range, Alaskan Air Command, U.S. Air Force. (a... enforced by the Commander, Alaskan Air Command, U.S. Air Force, Seattle, Washington, or such agencies as he...

33 CFR 334.1280 - Bristol Bay, Alaska; air-to-air weapon range, Alaskan Air Command, U.S. Air Force.

Code of Federal Regulations, 2013 CFR

2013-07-01

... weapon range, Alaskan Air Command, U.S. Air Force. 334.1280 Section 334.1280 Navigation and Navigable... REGULATIONS § 334.1280 Bristol Bay, Alaska; air-to-air weapon range, Alaskan Air Command, U.S. Air Force. (a... enforced by the Commander, Alaskan Air Command, U.S. Air Force, Seattle, Washington, or such agencies as he...

33 CFR 334.1280 - Bristol Bay, Alaska; air-to-air weapon range, Alaskan Air Command, U.S. Air Force.

Code of Federal Regulations, 2014 CFR

2014-07-01

... weapon range, Alaskan Air Command, U.S. Air Force. 334.1280 Section 334.1280 Navigation and Navigable... REGULATIONS § 334.1280 Bristol Bay, Alaska; air-to-air weapon range, Alaskan Air Command, U.S. Air Force. (a... enforced by the Commander, Alaskan Air Command, U.S. Air Force, Seattle, Washington, or such agencies as he...

33 CFR 334.1280 - Bristol Bay, Alaska; air-to-air weapon range, Alaskan Air Command, U.S. Air Force.

Code of Federal Regulations, 2010 CFR

2010-07-01

... weapon range, Alaskan Air Command, U.S. Air Force. 334.1280 Section 334.1280 Navigation and Navigable... REGULATIONS § 334.1280 Bristol Bay, Alaska; air-to-air weapon range, Alaskan Air Command, U.S. Air Force. (a... enforced by the Commander, Alaskan Air Command, U.S. Air Force, Seattle, Washington, or such agencies as he...

33 CFR 334.1280 - Bristol Bay, Alaska; air-to-air weapon range, Alaskan Air Command, U.S. Air Force.

Code of Federal Regulations, 2011 CFR

2011-07-01

... weapon range, Alaskan Air Command, U.S. Air Force. 334.1280 Section 334.1280 Navigation and Navigable... REGULATIONS § 334.1280 Bristol Bay, Alaska; air-to-air weapon range, Alaskan Air Command, U.S. Air Force. (a... enforced by the Commander, Alaskan Air Command, U.S. Air Force, Seattle, Washington, or such agencies as he...

The influence of isometric preload on power expressed during bench press in strength-trained men.

PubMed

Bartolomei, Sandro; Fukuda, David H; Hoffman, Jay R; Stout, Jeffrey R; Merni, Franco

2017-03-01

The purpose of this study was to compare the power expressed during the bench press exercise in resistance-trained men following different pre-activation conditions. Twenty-two trained men (age 24.1 ± 1.7 years, height 178.6 ± 6.1 cm, body mass 81.1 ± 10.6 kg) completed a maximal effort bench press (1-RM) test (100.0 kg ± 8.1 kg). In a subsequent assessment, each participant performed concentric bench press movements with loads of 20%, 30%, 40% and 50% of their 1-RM preceded by either a concentric contraction (CC), a low isometric preload (LIP; 70% 1-RM) or a high isometric preload (HIP; 100% 1-RM) conditions. All movements were performed in a Smith machine with a settable quick-release device. Participants performed all three conditions in randomized fashion. Results indicated that power outputs during the bench press exercise following HIP were significantly (p < 0.05) greater than CC at 20% 1-RM (+9%), 30% 1-RM (+16%) and 40% 1-RM (+14%), and LIP at 20% 1-RM (+4%), 30% 1-RM (+20%) and 40% 1-RM (+15%). No differences were found between conditions at 50% 1-RM. Area under the force-power curve with HIP was greater (p < 0.05) than with CC and LIP. In conclusion, results of this study indicate that the use of a HIP (100% 1-RM) in trained participants results in significantly greater power output during the concentric phase of a multi-joint exercise when compared to standard concentric movement.

A Lightweight, Precision-Deployable, Optical Bench for High Energy Astrophysics Missions

NASA Astrophysics Data System (ADS)

Danner, Rolf; Dailey, D.; Lillie, C.

2011-09-01

The small angle of total reflection for X-rays, forcing grazing incidence optics with large collecting areas to long focal lengths, has been a fundamental barrier to the advancement of high-energy astrophysics. Design teams around the world have long recognized that a significant increase in effective area beyond Chandra and XMM-Newton requires either a deployable optical bench or separate X-ray optics and instrument module on formation flying spacecraft. Here, we show that we have in hand the components for a lightweight, precision-deployable optical bench that, through its inherent design features, is the affordable path to the next generation of imaging high-energy astrophysics missions. We present our plans for a full-scale engineering model of a deployable optical bench for Explorer-class missions. We intend to use this test article to raise the technology readiness level (TRL) of the tensegrity truss for a lightweight, precision-deployable optical bench for high-energy astrophysics missions from TRL 3 to TRL 5 through a set of four well-defined technology milestones. The milestones cover the architecture's ability to deploy and control the focal point, characterize the deployed dynamics, determine long-term stability, and verify the stowed load capability. Our plan is based on detailed design and analysis work and the construction of a first prototype by our team. Building on our prior analysis and the high TRL of the architecture components we are ready to move on to the next step. The key elements to do this affordably are two existing, fully characterized, flight-quality, deployable booms. After integrating them into the test article, we will demonstrate that our architecture meets the deployment accuracy, adjustability, and stability requirements. The same test article can be used to further raise the TRL in the future.

Study of ignition, combustion, and production of harmful substances upon burning solid organic fuel at a test bench with a vortex chamber

NASA Astrophysics Data System (ADS)

Burdukov, A. P.; Chernetskiy, M. Yu.; Dekterev, A. A.; Anufriev, I. S.; Strizhak, P. A.; Greben'kov, P. Yu.

2016-01-01

Results of investigation of furnace processes upon burning of pulverized fuel at a test bench with a power of 5 MW are presented. The test bench consists of two stages with tangential air and pulverized coal feed, and it is equipped by a vibrocentrifugal mill and a disintegrator. Such milling devices have an intensive mechanical impact on solid organic fuel, which, in a number of cases, increases the reactivity of ground material. The processes of ignition and stable combustion of a mixture of gas coal and sludge (wastes of concentration plant), as well as Ekibastus coal, ground in the disintegrator, were studied at the test bench. The results of experimental burning demonstrated that preliminary fuel grinding in the disintegrator provides autothermal combustion mode even for hardly inflammable organic fuels. Experimental combustion of biomass, wheat straw with different lignin content (18, 30, 60%) after grinding in the disintegrator, was performed at the test bench in order to determine the possibility of supporting stable autothermal burning. Stable biofuel combustion mode without lighting by highly reactive fuel was achieved in the experiments. The influence of the additive GTS-Powder (L.O.M. Leaders Co., Ltd., Republic of Korea) in the solid and liquid state on reducing sulfur oxide production upon burning Mugun coal was studied. The results of experimental combustion testify that, for an additive concentration from 1 to 15% of the total mass of the burned mixture, the maximum SO2 concentration reduction in ejected gases was not more than 18% with respect to the amount for the case of burning pure coal.

33 CFR 334.630 - Tampa Bay south of MacDill Air Force Base, Fla.; small-arms firing range and aircraft jettison, U...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 3 2011-07-01 2011-07-01 false Tampa Bay south of MacDill Air Force Base, Fla.; small-arms firing range and aircraft jettison, U.S. Air Force, MacDill Air Force Base... Force Base, Fla.; small-arms firing range and aircraft jettison, U.S. Air Force, MacDill Air Force Base...

33 CFR 334.630 - Tampa Bay south of MacDill Air Force Base, Fla.; small-arms firing range and aircraft jettison, U...

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 3 2014-07-01 2014-07-01 false Tampa Bay south of MacDill Air Force Base, Fla.; small-arms firing range and aircraft jettison, U.S. Air Force, MacDill Air Force Base... Force Base, Fla.; small-arms firing range and aircraft jettison, U.S. Air Force, MacDill Air Force Base...

33 CFR 334.630 - Tampa Bay south of MacDill Air Force Base, Fla.; small-arms firing range and aircraft jettison, U...

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 3 2012-07-01 2012-07-01 false Tampa Bay south of MacDill Air Force Base, Fla.; small-arms firing range and aircraft jettison, U.S. Air Force, MacDill Air Force Base... Force Base, Fla.; small-arms firing range and aircraft jettison, U.S. Air Force, MacDill Air Force Base...

33 CFR 334.630 - Tampa Bay south of MacDill Air Force Base, Fla.; small-arms firing range and aircraft jettison, U...

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 3 2013-07-01 2013-07-01 false Tampa Bay south of MacDill Air Force Base, Fla.; small-arms firing range and aircraft jettison, U.S. Air Force, MacDill Air Force Base... Force Base, Fla.; small-arms firing range and aircraft jettison, U.S. Air Force, MacDill Air Force Base...

Finding of No Significant Impact: First Air Force Air Operations Center, First Air Force Headquarters/Air Force Forces Center, and Highway 98 Overpass at Tyndall Air Force Base, Florida

DTIC Science & Technology

2004-11-10

found at the following web address: <http://dep.state.fl.us/air/forms/asbestos.htm#asbestos>. The Air Force is advised to contact Sandra Veazey at...advised to contact Sandra Veazey at (850) 595·8300 for additional information on asbestos issues. http://tlhora6.dep.state.fl.us/clearinghouse/agency

Engineering Change Orders and their Impact on DoD Acquisition Contracts

DTIC Science & Technology

2017-03-23

Air Force Institute of Technology AFIT Scholar Theses and Dissertations 3-23-2017 Engineering Change Orders and their Impact on DoD Acquisition...MS-17-M-180 DEPARTMENT OF THE AIR FORCE AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY Wright-Patterson Air Force Base, Ohio DISTRIBUTION...School of Engineering and Management Air Force Institute of Technology Air University Air Education and Training Command In Partial Fulfillment of

United States Air Force Summer Research Program -- 1993. Volume 13. Phillips Laboratory

DTIC Science & Technology

1993-12-01

Research Kirtland Air Force Base, Albuquerque, NM August 1993 14-1 My Summer Apprenticeship At Kirtland Air Force Base, Phillips Laboratory Andrea Garcia...AFOSR Summer Research Program Phillips Laboratory Sponsored By: Air Force Office of Scientific Research Kirtland Air Force Base, Albuquerque, NM... Phillips Laboratory Sponsored by: Air

USAF/SCEEE Graduate Student Summer Research Program (1984). Program Management Report. Volume 1.

DTIC Science & Technology

1984-10-01

AFRL -TN-87, Air Force . Weapons Laboratory , Kirtland Air Foce...Mexico Research Location: Air Force Weapons Laboratory , NTATT, Kirtland Air Force Base, Albuquerque, NM 87117 .. USAF Research Contact: Dr. Carl E. Baum...Albuquerque, NM 87131 ... Research Location: Air Force Weapons Laboratory Kirtland Air Force Base Albuquerque, New Mexico 87117 USAF

Slipping and Tipping: Measuring Static Friction with a Straightedge

ERIC Educational Resources Information Center

Dietz, Eric; Aguilar, Isaac

2012-01-01

Following a discussion of forces, torques, and the conditions for static equilibrium, I tell my introductory mechanics class that I will show them how to measure the coefficient of static friction, us, between the surfaces of a block and the front bench using "nothing but a straightedge". After a few seconds of hushed anticipation, I nudge the…

An Experimental Investigation of the Role of Radiation in Laboratory Bench-Top Experiments in Thermal Physics

ERIC Educational Resources Information Center

Twomey, Patrick; O'Sullivan, Colm; O'Riordan, John

2009-01-01

A simple undergraduate experiment designed to study cooling purely by radiation and cooling by a combination of convection and radiation is described. Results indicate that the contribution from radiative cooling in normal laboratory experiments is more significant than students often realize, even in the case of forced cooling. (Contains 1…

System design and analysis of the trans-critical carbon-dioxide automotive air-conditioning system.

PubMed

Mu, Jing-Yang; Chen, Jiang-Ping; Chen, Zhi-Jiu

2003-01-01

As an environmentally harmless and feasible alternate refrigerant, CO2 has attracted worldwide attention, especially in the area of automobile air-conditioning (AAC). The thermal property of CO2 and its trans-critical refrigeration cycle is very different from that of the traditional CFC or HCFC system. The detailed process of CO2 system thermal cycle design and optimization is described in this paper. System prototype and performance test bench were developed to analyze the performance of the CO2 AAC system.

Bud-grafting yellow-poplar

Treesearch

David T. Funk

1963-01-01

Several years ago we began work on the vegetative propagation of yellow-poplar (Liriodendron tulipifera L.) with the aim of eventually establishing a clonal seed orchard. We tried field grafting, field budding, and air layering. We then attempted rooting cuttings in the greenhouse and in an indoor propagation bench. The best we could do with any of these methods was 4...

Air Force Weapons Laboratory Computational Requirements for 1976 Through 1980

DTIC Science & Technology

1976-01-01

Air Force Weapons Laboratory , Attn: DYS, Kirtland AFB, NM 87117...final report was prepared by the Air Force Weapons Laboratory , Kirtland Air Force Base, New Mexico under Job Order 06CB. Dr. Clifford E. Rhoades, Jr... Force Base, New Mexico 87117 62601F, 06CB II. CONTROLLING OFFICE NAME AND ADDRESS Ai"- Force Weapons Laboratory / Jan 1076 Kirtland Air Force Base,

33 CFR 334.730 - Waters of Santa Rosa Sound and Gulf of Mexico adjacent to Santa Rosa Island, Air Force Proving...

Code of Federal Regulations, 2011 CFR

2011-07-01

... Gulf of Mexico adjacent to Santa Rosa Island, Air Force Proving Ground Command, Eglin Air Force Base... Sound and Gulf of Mexico adjacent to Santa Rosa Island, Air Force Proving Ground Command, Eglin Air..., Headquarters Air Proving Ground Command, Eglin Air Force Base, Florida, and such agencies as he may designate...

A Systems Architecture and Advanced Sensors Application for Real-Time Aircraft Structural Health Monitoring

DTIC Science & Technology

2011-03-01

DEPARTMENT OF THE AIR FORCE AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY Wright-Patterson Air Force Base, Ohio APPROVED FOR PUBLIC RELEASE...position of the United States Air Force, Department of Defense, or the United States Government. This material is declared a work of the United...Management Graduate School of Engineering and Management Air Force Institute of Technology Air University Air Education and Training Command In

Final Environmental Assessment for the First Air Force Air Operations Center, First Air Force Headquarters/Air Force Forces Center, and Highway 98 Overpass at Tyndall Air Force Base, Florida

DTIC Science & Technology

2004-01-01

to contact Sandra Veazey at (850) 595-8300 for additional information on asbestos issues. The Florida Department of Transportation (FDOT) supports...The notification form for the Department can be found at the following web address:. The Air Force is advised to contact Sandra Veazey at (850) 595

Use of Strain Measurements from Acoustic Bench Tests of the Battleship Flowliner Test Articles To Link Analytical Model Results to In-Service Resonant Response

NASA Technical Reports Server (NTRS)

Frady, Greg; Smaolloey, Kurt; LaVerde, Bruce; Bishop, Jim

2004-01-01

The paper will discuss practical and analytical findings of a test program conducted to assist engineers in determining which analytical strain fields are most appropriate to describe the crack initiating and crack propagating stresses in thin walled cylindrical hardware that serves as part of the Space Shuttle Main Engine's fuel system. In service the hardware is excited by fluctuating dynamic pressures in a cryogenic fuel that arise from turbulent flow/pump cavitation. A bench test using a simplified system was conducted using acoustic energy in air to excite the test articles. Strain measurements were used to reveal response characteristics of two Flowliner test articles that are assembled as a pair when installed in the engine feed system.

Analysis of Organizational Architectures for the Air Force Tuition Assistance Program

DTIC Science & Technology

2003-03-01

FORCE TUITION ASSISTANCE PROGRAM THESIS Krista Zimmerman LaPietra AFIT/GOR/ENS/03-15 DEPARTMENT OF THE AIR FORCE AIR UNIVERSITY AIR...ANALYSIS OF ORGANIZATIONAL ARCHITECTURES FOR THE AIR FORCE TUITION ASSISTANCE PROGRAM THESIS Presented to the Faculty Department...ANALYSIS OF ORGANIZATIONAL ARCHITECTURES FOR THE AIR FORCE TUITION ASSISTANCE PROGRAM Krista Zimmerman LaPietra, BS

Subtask 3.11 - Production of CBTL-Based Jet Fuels from Biomass-Based Feedstocks and Montana Coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharma, Ramesh

The Energy & Environmental Research Center (EERC), in partnership with the U.S. Department of Energy (DOE) and Accelergy Corporation, an advanced fuels developer with technologies exclusively licensed from Exxon Mobil, undertook Subtask 3.11 to use a recently installed bench-scale direct coal liquefaction (DCL) system capable of converting 45 pounds/hour of pulverized, dried coal to a liquid suitable for upgrading to fuels and/or chemicals. The process involves liquefaction of Rosebud mine coal (Montana coal) coupled with an upgrading scheme to produce a naphthenic fuel. The upgrading comprises catalytic hydrotreating and saturation to produce naphthenic fuel. A synthetic jet fuel was preparedmore » by blending equal volumes of naphthenic fuel with similar aliphatic fuel derived from biomass and 11 volume % of aromatic hydrocarbons. The synthetic fuel was tested using standard ASTM International techniques to determine compliance with JP-8 fuel. The composite fuel thus produced not only meets but exceeds the military aviation fuel-screening criteria. A 500-milliliter synthetic jet fuel sample which met internal screening criteria was submitted to the Air Force Research Laboratory (AFRL) at Wright–Patterson Air Force Base, Dayton, Ohio, for evaluation. The sample was confirmed by AFRL to be in compliance with U.S. Air Force-prescribed alternative aviation fuel initial screening criteria. The results show that this fuel meets or exceeds the key specification parameters for JP-8, a petroleum-based jet fuel widely used by the U.S. military. JP-8 specifications include parameters such as freeze point, density, flash point, and others; all of which were met by the EERC fuel sample. The fuel also exceeds the thermal stability specification of JP-8 fuel as determined by the quartz crystalline microbalance (QCM) test also performed at an independent laboratory as well as AFRL. This means that the EERC fuel looks and acts identically to petroleum-derived jet fuel and can be used interchangeably without any special requirements and thus provides a pathway to energy security to the U.S. military and the entire nation. This subtask was funded through the EERC–DOE Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FC26- 08NT43291. Nonfederal funding was provided by Accelergy Corporation.« less

32 CFR Appendix A to Part 806 - References

Code of Federal Regulations, 2011 CFR

2011-07-01

... Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE ADMINISTRATION AIR FORCE FREEDOM OF..., Air Force Security and Policy Review Program AFI 36-2603, Air Force Board for Correction of Military... Responsibility AFI 36-2907, Unfavorable Information File (UIF) Program AFPD 37-1, Air Force Information...

32 CFR Appendix A to Part 806 - References

Code of Federal Regulations, 2013 CFR

2013-07-01

... Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE ADMINISTRATION AIR FORCE FREEDOM OF..., Air Force Security and Policy Review Program AFI 36-2603, Air Force Board for Correction of Military... Responsibility AFI 36-2907, Unfavorable Information File (UIF) Program AFPD 37-1, Air Force Information...

32 CFR 806b.1 - Summary of revisions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... for the Air Force Privacy Program from Air Force Communications and Information Center to the Air Force Chief Information Officer; prescribes Air Force Visual Aid 33-276, Privacy Act Label as optional... are new or have major changes; changes appeal processing from Air Force Communications and Information...

Physiological profile of a professional boxer preparing for Title Bout: A case study.

PubMed

Halperin, Israel; Hughes, Steven; Chapman, Dale W

2016-10-01

This study aimed to (1) profile a professional boxer (23 years and 80 kg) with boxing-specific, muscle function, aerobic capacity and body composition tests, and (2) quantify how these measures varied during an 8-week preparation phase leading to, and post a state-Title Bout fought in the 76.2-kg class. A series of boxing-specific and muscle function tests were completed on 11 occasions: 9 prior and twice after the bout, each separated by approximately 2 weeks. The boxing test included 36 maximal punches (9 of each: lead and rear straights, lead and rear hooks) to a punching integrator measuring forces and velocity. Muscle function tests included countermovement jump, drop-jumps, isometric mid-thigh pull and isometric bench-press. Body composition was assessed using skin-fold measurements on three occasions and one dual energy X-ray absorptiometry scan. Aerobic capacity was assessed using 2 VO2 max tests. Leading up to the bout, performance decreased in isometric mid-thigh pull (8%), isometric bench-press (5%), countermovement jump (15%) and impact forces in 3 of 4 punches (4%-7%). Whereas measures of dynamic and isometric muscle function remained depressed or unchanged post competition, punching forces (6%-15%) and aerobic power (6%) increased. Data suggest the athlete may have super-compensated following rest as fatigue dissipated and further adaptation occurred.

32 CFR 855.22 - Air Force procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 6 2013-07-01 2013-07-01 false Air Force procedures. 855.22 Section 855.22 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL AIRCRAFT USE OF UNITED STATES AIR FORCE AIRFIELDS Agreements for Civil Aircraft Use of Air Force Airfields § 855...

32 CFR 855.22 - Air Force procedures.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Air Force procedures. 855.22 Section 855.22 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL AIRCRAFT USE OF UNITED STATES AIR FORCE AIRFIELDS Agreements for Civil Aircraft Use of Air Force Airfields § 855...

32 CFR 855.22 - Air Force procedures.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 6 2011-07-01 2011-07-01 false Air Force procedures. 855.22 Section 855.22 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL AIRCRAFT USE OF UNITED STATES AIR FORCE AIRFIELDS Agreements for Civil Aircraft Use of Air Force Airfields § 855...

STEM Education: Introduction of Quantitative Math and Science Content into Elementary Education, STEM Enrichment Effort in Title One Elementary and Middle Schools in Bay County, Florida

DTIC Science & Technology

2013-06-01

inside pages STINFO COPY AIR FORCE RESEARCH LABORATORY MATERIALS AND MANUFACTURING DIRECTORATE WRIGHT PATTERSON AIR FORCE BASE, OH 45433-7750...Materials and Manufacturing Directorate Materials and Manufacturing Directorate Air Force Research Laboratory Air Force Research Laboratory This... Research Laboratory Materials and Manufacturing Directorate Wright Patterson Air Force Base, OH 45433-7750 Air Force Materiel Command United States

[Aviation medicine: yesterday, today and tomorrow].

PubMed

Iamenskov, V V; Khafizov, N N; Morozov, A V

2011-04-01

The article describes the history and current state of medical support of the Air Force. On December 1, 2009 Air Force Medical Service was renamed into the service of aviation medicine of Command Air Forces, and many of the functions of medical support of the Air Force transferred to the newly formed Air Force Center of Aviation Medicine. April 29, 2011 office of Aviation Medicine of the High Command of the Air Force has stepped 95-year milestone. The changes affected all structures entrusted with the issues of medical support of the Air Force. Today, the medical service of the Air Force faces challenges--ensuring safety, the study of flight conditions and their impact on health, job performance and psychological characteristics of flight personnel.

Hazardous waste: Siting of storage facility at Kelly Air Force Base, Texas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1987-01-01

This report provides information on whether the hazardous waste storage facility at Kelly Air Force Base meets Resource Conservation and Recovery Act, state, and Air Force siting requirements; on whether the Air Force or the Defense Reutilization and Marketing Office selected the best site available to protect the public and to preserve good public relations with the community; on whether the Air Force, Kelly Air Force Base, or the Defense Logistics Agency adjusted siting standards as a result of the adverse publicity the hazardous waste facility has generated; and on whether Kelly Air Force Base is revising its hazardous wastemore » management organization so that it is similar to the organizations at Tinker and McClellan Air Force Bases.« less

Scientific and Technological Achievements, 1946-2011, of the AFRL Electromagnetics Technology Division (AFRL/RYH) and Its Progenitors

DTIC Science & Technology

2012-07-01

AFRL /RYH) Sensors Directorate Air Force Research Laboratory Wright-Patterson Air Force ...Lossless Acoustic Monopoles, Electric Dipoles, and Magnetodielectric Spheres, Air Force Research Laboratory in-house report AFRL -SN-HS-TR-2006-0039... FORCE RESEARCH LABORATORY SENSORS DIRECTORATE WRIGHT-PATTERSON AIR FORCE BASE, OH 45433-7320 AIR FORCE MATERIEL COMMAND UNITED

78 FR 32241 - U.S. Air Force Seeks Industry Input for National Security Space Launch Assessment

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-29

... Security Space Launch Assessment AGENCY: Office of the Deputy Under Secretary of the Air Force for Space... that the United States Air Force, Office of the Deputy Under Secretary of the Air Force for Space.... Robert Long, 703-693-4978, Office of the Deputy Under Secretary of the Air Force for Space, 1670 Air...

Simulation and Experiment Research on Fatigue Life of High Pressure Air Pipeline Joint

NASA Astrophysics Data System (ADS)

Shang, Jin; Xie, Jianghui; Yu, Jian; Zhang, Deman

2017-12-01

High pressure air pipeline joint is important part of high pressure air system, whose reliability is related to the safety and stability of the system. This thesis developed a new type-high pressure air pipeline joint, carried out dynamics research on CB316-1995 and new type-high pressure air pipeline joint with finite element method, deeply analysed the join forms of different design schemes and effect of materials on stress, tightening torque and fatigue life of joint. Research team set up vibration/pulse test bench, carried out joint fatigue life contrast test. The result shows: the maximum stress of the joint is inverted in the inner side of the outer sleeve nut, which is consistent with the failure mode of the crack on the outer sleeve nut in practice. Simulation and experiment of fatigue life and tightening torque of new type-high pressure air pipeline joint are better than CB316-1995 joint.

Balances for the measurement of multiple components of force in flows of a millisecond duration

NASA Technical Reports Server (NTRS)

Mee, D. J.; Daniel, W. J.; Tuttle, S. L.; Simmons, J. M.

1995-01-01

This paper reports a new balance for the measurement of three components of force - lift, drag and pitching moment - in impulsively starting flows which have a duration of about one millisecond. The basics of the design of the balance are presented and results of tests on a 15 deg semi-angle cone set at incidence in the T4 shock tunnel are compared with predictions. These results indicate that the prototype balance performs well for a 1.9 kg, 220 mm long model. Also presented are results from initial bench tests of another application of the deconvolution force balance to the measurement of thrust produced by a 2D scramjet nozzle.

General Electric Unattended Power System Study. Addendum

DTIC Science & Technology

1980-05-01

AND NAVIGATION SYSTEMS ELECTRONIC SYSTEMS DIVISION AIR FORCE SYSTEMS COMMAND UNITED STATES AIR FORCE Hascom Air Force Base, Massachusetts DTIC C-3 B I...MITRE Corporation under Project No. 633A. The contract is sponsored by the Electronic Systems *Division, Air Force Systems Command, Hanscom Air Force...is delivered fully integrated, tested, and certified. The system consists of a combustion system, vapor generator, turbo- alternator, air -cooled

Very Long Wave Length IR Detectors

DTIC Science & Technology

2015-02-01

STINFO COPY AIR FORCE RESEARCH LABORATORY MATERIALS AND MANUFACTURING DIRECTORATE WRIGHT-PATTERSON AIR FORCE BASE, OH 45433-7750 AIR FORCE...to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE...NAME(S) AND ADDRESS(ES) Air Force Research Laboratory Materials and Manufacturing Directorate Wright-Patterson Air Force Base, OH 45433-7750 Air

Starfleet Deferred: Project Orion in the 1962 Air Force Space Program

NASA Astrophysics Data System (ADS)

Ziarnick, B.

Project Orion, the Cold War American program (1957-1965) studying nuclear pulse propulsion for space applications, has long interested space enthusiasts for what it was and what it might have been, but it has long been believed that neither the United States government nor the US Air Force took the program very seriously. However, recently declassified US Air Force documents shed more light on the classified history of Project Orion. Far from being ignored by Air Force leadership, through the efforts of the Strategic Air Command, Air Force leaders like General Curtis LeMay were convinced that Project Orion should be funded as a major weapons system. The high water mark of Project Orion was the 1962 Air Force Space Program proposal by the Air Force Chief of Staff to devote almost twenty percent of the Air Force space budget from 1962-1967 to Orion development before the program was cancelled by the civilian Secretary of the Air Force under pressure from the Department of Defense. This paper details the history of Project Orion in the 1962 Air Force Space Program proposal, and concludes with a few lessons learned for use by modern interstellar advocates.

The Air Force’s Experience with Should-Cost Reviews and Options for Enhancing Its Capability to Conduct Them

DTIC Science & Technology

2012-01-01

Patterson Air Force Base, Ohio: Air Force Institute of Technology, 1972. Williams , Robert Leon, A Review of the “Should Cost” Process and Management Issues...We thank William Bartlebaugh of the Air Force Cost Analysis Agency; David Dudley of the Air Force Electronics System Center; Tommy Gilbert of Warner...better performance. The program experienced large cost overruns. Air Force Deputy for Management Systems A. Ernest Fitzgerald, on the staff of the

List of EPA Certified Forced-Air Furnaces

EPA Pesticide Factsheets

The EPA-Certified Forced-Air Furnace list contains EPA-certified forced-air furnaces that meet the 2015 NSPS for New Residential Wood Heaters, New Residential Hydronic Heaters and Forced-Air Furnaces.

USAF Summer Research Program - 1993 Summer Research Extension Program Final Reports, Volume 2, Phillips Laboratory

DTIC Science & Technology

1994-11-01

Research Extension Program Phillips Laboratory Kirtland Air Force Base Sponsored by: Air Force Office of Scientific Research Boiling Air Force Base...Program Phillips Laboratory Sponsored by: Air Force Office of Scientific Research Bolling Air Force Base, Washington, D.C. and Arkansas Tech University...Summer Research Extension Program (SREP) Phillips

Report on Operations of the Air Force Geophysics Laboratory Infrared Array Spectrometer

DTIC Science & Technology

1993-01-25

AIR FORCE GEOPHYSICS LABORATORY INFRARED ARRAY... LABORATORY Directorate of Geophysics AIR FORCE MATERIEL COMMAND HANSCOM AIR FORCE BASE, MA 01731-3010 93-27655IEEE|EIIE1ENI This technical report has...ACKNOWLEDGMENT We are grateful to the Air Force Office of Scientific Research , especially Henry Radowski. for their financial corn- mitment to this project.

Summer Research Program (1992). Summer Faculty Research Program (SFRP) Reports. Volume 3. Phillips Laboratory.

DTIC Science & Technology

1992-12-28

Phillips Laboratory Kirtland Air Force Base NM 87117-6008 Sponsored by: Air Force Office of Scientific Research Bolling Air Force Base...Zindel, D.: 1963, Z. Astrophys. 57, 82. 29-13 FINAL REPORT SUMMER FACULTY RESEARCH PROGRAM AT PHILLIPS LABORATORY KIRTLAND AIR FORCE BASE...Program Phillips Laboratory Sponsored by: Air Force Office of Scientific

Deformed Shape Analysis of Coupled Glazing Systems

DTIC Science & Technology

2013-09-01

Tyndall Air Force Base, Florida, USA ABSTRACT Glazing in storefront and curtain wall configurations is increasingly used in areas subjected to... AIR FORCE CIVIL ENGINEER CENTER READINESS DIRECTORATE  Requirements & Acquisition Division  United States Air Force  Tyndall Air Force...Antonio, Texas; %Omaha, Nebraska #Jacobs Technology, Fort Walton Beach, Florida Air Force Civil Engineer Center Readiness Directorate Requirements

Startle Auditory Stimuli Enhance the Performance of Fast Dynamic Contractions

PubMed Central

Fernandez-Del-Olmo, Miguel; Río-Rodríguez, Dan; Iglesias-Soler, Eliseo; Acero, Rafael M.

2014-01-01

Fast reaction times and the ability to develop a high rate of force development (RFD) are crucial for sports performance. However, little is known regarding the relationship between these parameters. The aim of this study was to investigate the effects of auditory stimuli of different intensities on the performance of a concentric bench-press exercise. Concentric bench-presses were performed by thirteen trained subjects in response to three different conditions: a visual stimulus (VS); a visual stimulus accompanied by a non-startle auditory stimulus (AS); and a visual stimulus accompanied by a startle auditory stimulus (SS). Peak RFD, peak velocity, onset movement, movement duration and electromyography from pectoralis and tricep muscles were recorded. The SS condition induced an increase in the RFD and peak velocity and a reduction in the movement onset and duration, in comparison with the VS and AS condition. The onset activation of the pectoralis and tricep muscles was shorter for the SS than for the VS and AS conditions. These findings point out to specific enhancement effects of loud auditory stimulation on the rate of force development. This is of relevance since startle stimuli could be used to explore neural adaptations to resistance training. PMID:24489967

United States Air Force Graduate Student Research Program. 1989 Program Management Report

DTIC Science & Technology

1989-12-01

research at Air Force laboratories /centers. Each assignment is in a subject area and at an Air Force facility mutually agreed upon by the...housing difficult to find, c) 10 weeks too short for research period. June 20, 1989 Astronautics Laboratory Edwards Air Force Base, California June 21...1989 HRL: Operations Training Division Williams Air Force Base, Arizona June 22, 1989 Weapons Laboratory Kirtland Air

Units

Science.gov Websites

Maxwell Air Force Base Maxwell Air Force Base Join the Air Force Home News AF News Commentaries Services SAPR FOIA Retiree Activities Office Centennial Search Maxwell Air Force Base: Home > Units Site

Study on energy saving effect of IHX on vehicle air conditioning system

NASA Astrophysics Data System (ADS)

Li, Huguang; Tong, Lin; Xu, Ming; Wei, Wangrui; Zhao, Meng; Wang, Long

2018-02-01

In this paper, the performance of Internal Heat Exchanger (IHX) air conditioning system for R134a is investigated in bench test and vehicle test. Comparison for cooling capacity and energy consumption between IHX air conditioning system and traditional tube air conditioning system are conducted. The suction temperature and discharge temperature of compressor is also recorded. The results show that IHX air conditioning system has higher cooling capacity, the vent temperature decrease 2.3 °C in idle condition. But the suction temperature and discharge temperature of compressor increase 10°C. IHX air conditioning system has lower energy consumption than traditional tube air conditioning system. Under the experimental conditions in this paper, the application of IHX can significantly reduce the energy consumption of air conditioning system. At 25°C of environment temperature, AC system energy consumption decrease 14%, compressor energy consumption decrease 16%. At 37°C of environment temperature, AC system energy consumption decrease 16%, compressor energy consumption decrease 13%.

An economical 20 litre bench-top fermenter.

PubMed

Thiel, Michael A; Coster, Douglas J; Mavrangelos, Christos; Zola, Heddy; Williams, Keryn A

2002-10-01

We describe an economical 20 litre bench-top fermenter suitable for production of recombinant antibody fragments in bacterial expression systems. The bacterial culture contained within a polycarbonate carboy is mixed (400-600 rpm) and aerated (1 vessel vol./min) by a high-shear radial flow impeller mounted on a hollow stainless steel shaft, through which pressurised air is pumped. Air is dispersed as fine bubbles into the culture medium by the turbine impeller, without the need for a porous sparger. A stainless steel baffle stabilised by a gliding counterweight increases mixing. The components can easily be disassembled for cleaning and sterilisation. Temperature (range 20-37 degrees C) and pH (range 7.0-7.5) are controlled manually. Using the apparatus, it proved possible to achieve Escherichia coli cell culture densities equivalent to an optical density at 600 nm (OD(600)) of 30-32, compared with OD(600) 4-6 in shake flasks. A yield of 40 mg/litre/day of a recombinant antibody fragment was obtained with the fermenter, which was 15-fold more than the yield of 2.5mg/litre/day achieved in shake flasks. The fermenter may be particularly suited for research purposes.

Computational fluid dynamics assessment: Volume 2, Isothermal simulations of the METC bench-scale coal-water slurry combustor: Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Celik, I.; Chattree, M.

1988-09-01

The isothermal turbulent, swirling flow inside the METC pressurized bench-scale combustor has been simulated using ISOPCGC-2. The effects of the swirl numbers, the momentum ratio of the primary to secondary streams, the annular wall thickness, and the quarl angle on the flow and mixing patterns have been investigated. The results that with the present configuration of the combustor, an annular recirculation zone is present up to secondary swirl number of four. A central (on axis) recirculation zone can be obtained by increasing the momentum of the secondary stream by decreasing the annular area at the reactor inlet. The mixing ofmore » the primary (fuel carrier) air with the secondary air improves only slightly due to swirl unless a central recirculation zone is present. Good mixing is achieved in the quarl region when a central recirculation zone is present. A preliminary investigation of the influence of placing flow regulators inside the the combustor shows that they influence the flow field significantly and that there is a potential of obtaining optimum flow conditions using these flow regulators. 58 refs., 47 figs., 12 tabs.« less

Creating Joint Leaders Today for a Successful Air Force Tomorrow (1REV)

DTIC Science & Technology

2016-04-01

armed force in the same grade and competitive category who are serving on, or have served on, the HQ staff of their armed force; and 2. Officers in the...period from the release of the promotion results and the pin-on date. 5 Department of the Air Force, HQ Air Force Personnel Center, Demographics and...2009), Section 619a. 9 ibid, Section 619a. 10 Department of the Air Force, HQ Air Force Personnel Center, A-1 Manpower Division. 11 Phone

Finite Element Model Optimization of the FalconSAT-5 Structural Engineering Model

DTIC Science & Technology

2009-03-01

for coupled loads analyses. To develop the FE tuning process, this research focuses on the United States Air Force Academy (USAFA) FalconSAT-5 SEM II...Kirtland Air Force Base (KAFB) were sufficient for design engineers to ensure compliance with launch loads. However, for the coupled loads analysis...OF THE AIR FORCE AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY Wright-Patterson Air Force Base, Ohio APPROVED FOR PUBLIC RELEASE; DISTRIBUTION

Biodefense and Deterrence: A Critical Element in the New Triad

DTIC Science & Technology

2009-02-01

College, Air university Maxwell Air Force Base , Alabama 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING/MONITORING AGENCY NAME(S) AND ADDRESS(ES...Headquarters, Brussels Belgium, Headquarters Twenty-First Air Force, and 21st Expeditionary Mobility Task Force, McGuire Air Force Base , New Jersey...Colonel Owens was the Commander, 816th Global Mobility Squadron, and Commander, 821st Air Mobility Squadron, McGuire Air Force Base , New Jersey. Prior to

Petrography, palynology, and paleoecology of the Lower Pennsylvanian Bon Air coal, Franklin County, Cumberland Plateau, southeast Tennessee

USGS Publications Warehouse

Shaver, S.A.; Eble, C.F.; Hower, J.C.; Saussy, F.L.

2006-01-01

Stratigraphy, palynology, petrography, and geochemistry of the Bon Air coal from the Armfield, Dotson, Rutledge, and Shakerag mine sites of Franklin County, Tennessee suggest that Bon Air seams at all sites were small (??? 1.0 mile, 1.6 km), spatially distinct paleomires that evolved from planar to domed within the fluviodeltaic Lower Pennsylvanian Raccoon Mountain Formation. Of observed palynoflora, 88-97% are from lycopsids prevalent in the Westphalian. Densosporites palynomorphs of small lycopsids (e.g., Omphalophloios) dominate at the shale-hosted Armfield site, while Lycospora palynoflora of large arboreous lycopsids (especially Lepidodendron, with lesser Lepidophloios harcourtii and Lepidophloios hallii) dominate where intercalated siltstone/sandstone/shale hosts the coal (all other sites). Palynoflora of other lycopsids (Sigillaria and Paralycopodites), tree ferns, seed ferns, small ferns, calamites, and cordaites are generally minor. Genera of clastic-associated Paralycopodites are most common in Shakerag's coal (??? 10%), yet quite rare in Rutledge or Dotson coals. Overall, the palynomorph assemblages suggest that the Bon Air paleomires were forest swamps, and Early Pennsylvanian in age (Westphalian A, Langsettian). Dominant macerals at all sites are vitrinites, with fine collodetrinite (from strongly decomposed plant debris) more common than coarser collotelinite (from well-preserved plant fragments), and with lesser inertinites (fusinite and semifusinite) and liptinites (dominantly sporinite). Shakerag's coal has greatest abundance (mineral-matter-free) of collotelinite (up to 47%) and total vitrinite (74-79%) of any sites, but lowest liptinite (12-14.5%) and inertinite (7-11%). The Dotson and Rutledge seams contain moderate liptinite (21-23%) and highest inertinite (36-37%), lowest vitrinite (??? 41%), and lowest collotelinite (13-15%). Armfield's seam has relatively high liptinite (26-28%) and vitrinite (56.5-62%), but rather low inertinite (12-15%). Moderately high ash (11.0-20.0%) and low to moderate sulfur (1.24% avg.) are typical, but ash may locally be up to 38% and sulfur up to 2.9%. Volatile matter (32.1-41.3%), calorific value (33.3-34.9 MJ/kg MAF), moisture (2.2-3.4%), and vitrinite reflectance (0.70-0.84% Rmax; 0.64-0.79% Rrandom) place the Bon Air's rank as high-volatile-A bituminous (hvAb). The Armfield coal was probably a channel-distal paleomire, perhaps an oxbow lake or floodplain depression, which domed and then subsided back to planarity prior to burial. Features of its basal and uppermost benches suggest low-lying, often-flooded (but periodically dry) mires marked by fluvial influxes and diverse lycopsid growth. These include variable inertinite, common palynoflora of both small lycopsids (Omphalophloios-like) and large arboreous ones (Lepidophloios and Lepidodendron), minor but significant palynoflora of subaerial levee or levee/mire transition species (especially Paralycopodites), moderate to high ash, variable sulfur, and elevated levels of commonly fluvial trace elements (e.g., Al, Cr, REEs, Rb, Sr, Th, V, Y, and Zr). These benches also contain high total vitrinite, high collotelinite/collodetrinite ratios, and clays with moderate to low kaolinite/quartz ratios, all consistent with the near-neutral pH and limited peat degradation that typify such planar mires. By contrast, middle benches at Armfield reflect mires domed above the land surface, less-often flooded, less-preservational, and of lower pH: coals have lower ash, vitrinite, and collotelinite, less palynoflora of both large arboreous lycopsids and Paralycopodites, and high proportions of kaolinite, liptinite, and Densosporites. Similar data at Shakerag suggest that its mire also grew from planar to domed. However, more abundant Paralycopodites, a kaolinite-poor but quartz-and-illite-rich underclay, benches alternately ash-rich and ash-poor, and an upper bench truncated by channel sandstone, suggest that it was channel-proximal and pron

78 FR 63459 - Names of Members of the Performance Review Board for the Department of the Air Force

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-24

.... Air Force are: 1. Board President--Gen Shelton, Commander, Air Force Space Command 2. Lt Gen... DEPARTMENT OF DEFENSE Department of the Air Force Names of Members of the Performance Review Board for the Department of the Air Force ACTION: Notice. SUMMARY: Notice is given of the names of members...

Science and Technology: The Making of the Air Force Research Laboratory

DTIC Science & Technology

2000-01-01

AFRL . . . . . . . . . . . 187 11 Air Force Research Laboratory : Before and After...United States Air Force during my tenure as chief of staff—the crea - tion of the Air Force Research Laboratory ( AFRL ). As the “high technology” service...consolidate four existing laboratories into one Air Force Research Laboratory ( AFRL ) designed to lead to a more efficient and streamlined

Semiconducter Optical Amplifier as a Phase Modulator for Coherent Laser Radar (Preprint)

DTIC Science & Technology

2012-01-01

AIR FORCE RESEARCH LABORATORY SENSORS DIRECTORATE WRIGHT-PATTERSON AIR FORCE BASE, OH 45433-7320 AIR FORCE MATERIEL COMMAND UNITED STATES... AIR FORCE NOTICE AND SIGNATURE PAGE Using Government drawings, specifications, or other data included in this document for any purpose other...NUMBER Multispectral Sensing and Detection Division LADAR Technology Branch (AFRL/RYMM) Air Force Research Laboratory, Sensors Directorate Wright

Defense.gov - Special Report - Travels With Gates

Science.gov Websites

Force Base, Ala. Story» Warfighter Care at Center of 2010 Budget Considerations MAXWELL AIR FORCE BASE , Ala., April 15, 2009 – Defense Secretary Robert M. Gates met at Maxwell Air Force Base, Ala., with the U.S. Air Force Air War College on Maxwell Air Force Base, Ala., listen to Defense Secretary Robert

Use of Demographics to Predict High Risk Individuals for Suicide

DTIC Science & Technology

2013-06-01

GRP-13-J-15 DEPARTMENT OF THE AIR FORCE AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY Wright-Patterson Air Force Base, Ohio APPROVED...Department of Operational Sciences Graduate School of Engineering and Management Air Force Institute of Technology Air University Air Education and...Health Statistics. The military data is collected from the DOD Suicide Event Reports (DODSER) from the National Center for Telehealth and Technology

32 CFR 842.11 - Air Force claims organization.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 6 2013-07-01 2013-07-01 false Air Force claims organization. 842.11 Section 842.11 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE CLAIMS AND LITIGATION ADMINISTRATIVE CLAIMS Functions and Responsibilities § 842.11 Air Force claims organization. Air...

Management and Oversight of Services Acquisition Within the United States Air Force

DTIC Science & Technology

2008-12-01

Air Mobility Command AFDW Air Force District of Washington AFSPC Air Force Space Command AT&L Acquisition Technologies and Logistics CPM ...were commonly performed in industry. The types of services included advertising for Navy recruitment, custodial services on Air Force bases, and on

32 CFR 842.11 - Air Force claims organization.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Air Force claims organization. 842.11 Section 842.11 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE CLAIMS AND LITIGATION ADMINISTRATIVE CLAIMS Functions and Responsibilities § 842.11 Air Force claims organization. Air...

32 CFR 842.11 - Air Force claims organization.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 6 2011-07-01 2011-07-01 false Air Force claims organization. 842.11 Section 842.11 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE CLAIMS AND LITIGATION ADMINISTRATIVE CLAIMS Functions and Responsibilities § 842.11 Air Force claims organization. Air...

77 FR 5781 - Record of Decision for the Air Space Training Initiative Shaw Air Force Base, South Carolina...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-06

... DEPARTMENT OF DEFENSE Department of the Air Force Record of Decision for the Air Space Training Initiative Shaw Air Force Base, South Carolina Final Environmental Impact Statement ACTION: Notice of Availability (NOA) of a Record of Decision (ROD). SUMMARY: On December 9, 2011, the United States Air Force...

32 CFR 806.29 - Administrative processing of Air Force FOIA requests.

Code of Federal Regulations, 2012 CFR

2012-07-01

... section. (c) Contacts with FOIA requesters and non-Air Force submitters of data. (1) Contacts with Air... memoranda documenting requester contacts with Air Force elements regarding a pending FOIA request in the requester's FOIA file. If the requester contacts Air Force elements telephonically about a pending FOIA...

32 CFR 806.29 - Administrative processing of Air Force FOIA requests.

Code of Federal Regulations, 2011 CFR

2011-07-01

... section. (c) Contacts with FOIA requesters and non-Air Force submitters of data. (1) Contacts with Air... memoranda documenting requester contacts with Air Force elements regarding a pending FOIA request in the requester's FOIA file. If the requester contacts Air Force elements telephonically about a pending FOIA...

32 CFR 806.29 - Administrative processing of Air Force FOIA requests.

Code of Federal Regulations, 2014 CFR

2014-07-01

... section. (c) Contacts with FOIA requesters and non-Air Force submitters of data. (1) Contacts with Air... memoranda documenting requester contacts with Air Force elements regarding a pending FOIA request in the requester's FOIA file. If the requester contacts Air Force elements telephonically about a pending FOIA...

Surgically Shaping a Financial Hydra: Reprogramming United States Air Force End Strength to the Air Reserve Component

DTIC Science & Technology

2012-02-14

Director of the Air National Guard20 Lt Gen Charles E. Stenner Jr., Chief of the Air Force Reserve21 Specificity about what rebalancing the force...January 2012). Sharp, Travis. Vision Meets Reality: 2010 QDR and 2011 Defense Budget. Center for a New American Security, February 2010. Stenner ...Lt Gen Charles E. Stenner Jr., commander of Air Force Reserve Command (address, Air Force Reserve Senior Leader Conference

76 FR 52643 - Notice Is Given of the Names of Members of a Performance Review Board for the Department of the...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-23

.... Air Force are: 1. Board President--Gen. Shelton, Commander, Air Force Space Command; 2. Lt. Gen. Lord... DEPARTMENT OF DEFENSE Department of the Air Force Notice Is Given of the Names of Members of a Performance Review Board for the Department of the Air Force AGENCY: Department of the Air Force, DOD. ACTION...

Nanoscience and Technology at the Air Force Research Laboratory (AFRL)

DTIC Science & Technology

2005-05-01

AIR FORCE RESEARCH LABORATORY ( AFRL ) Dr. Richard A. Vaia Dr. Daniel Miracle Dr. Thomas Cruse Air Force Research ...Technology At The Air Force Research Laboratory ( AFRL ) 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT...98) Prescribed by ANSI Std Z39-18 AFRL NST Overview 2 AIR FORCE RESEARCH LABORATORY VISION We defend

Nanoscience and Technology at the Air Force Research Laboratory (AFRL)

DTIC Science & Technology

2005-02-01

AIR FORCE RESEARCH LABORATORY ( AFRL ) Dr. Richard A. Vaia Dr. Daniel Miracle Dr. Thomas Cruse Air Force Research ...Technology At The Air Force Research Laboratory ( AFRL ) 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT...98) Prescribed by ANSI Std Z39-18 AFRL NST Overview 2 AIR FORCE RESEARCH LABORATORY VISION We defend

33 CFR 334.730 - Waters of Santa Rosa Sound and Gulf of Mexico adjacent to Santa Rosa Island, Air Force Proving...

Code of Federal Regulations, 2010 CFR

2010-07-01

... Gulf of Mexico adjacent to Santa Rosa Island, Air Force Proving Ground Command, Eglin Air Force Base... Sound and Gulf of Mexico adjacent to Santa Rosa Island, Air Force Proving Ground Command, Eglin Air Force Base, Fla. (a) The danger zones—(1) Prohibited area. Waters of Santa Rosa Sound and Gulf of Mexico...

Experimental Methods to Characterize Nonlinear Vibration of Flapping Wing Micro Air Vehicles

DTIC Science & Technology

2007-03-01

EXPERIMENTAL METHODS TO CHARACTERIZE NONLINEAR VIBRATION OF FLAPPING WING MICRO AIR VEHICLES THESIS Adam P. Tobias, Captain, USAF...AFIT/GAE/ENY/07-M23 DEPARTMENT OF THE AIR FORCE AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY Wright-Patterson Air Force Base, Ohio...author and do not reflect the official policy or position of the United States Air Force, Department of Defense, or the United States Government

2. GENERAL VIEW OF SLC3 AIR FORCE BUILDING (BLDG. 761) ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. GENERAL VIEW OF SLC-3 AIR FORCE BUILDING (BLDG. 761) FROM THE NORTHWEST - Vandenberg Air Force Base, Space Launch Complex 3, SLC-3 Air Force Building, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

1. GENERAL VIEW OF SLC3 AIR FORCE BUILDING (BLDG. 761) ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. GENERAL VIEW OF SLC-3 AIR FORCE BUILDING (BLDG. 761) FROM THE SOUTHWEST - Vandenberg Air Force Base, Space Launch Complex 3, SLC-3 Air Force Building, Napa & Alden Roads, Lompoc, Santa Barbara County, CA

33 CFR 334.1300 - Blying Sound area, Gulf of Alaska, Alaska; air-to-air gunnery practice area, Alaskan Air Command...

Code of Federal Regulations, 2014 CFR

2014-07-01

..., Alaska; air-to-air gunnery practice area, Alaskan Air Command, U.S. Air Force. 334.1300 Section 334.1300... gunnery practice area, Alaskan Air Command, U.S. Air Force. (a) The danger zone. A rhomboidal area... Air Command, U.S. Air Force, Anchorage, Alaska, or such agencies as he may designate. (Sec. 7, 40 Stat...

33 CFR 334.1300 - Blying Sound area, Gulf of Alaska, Alaska; air-to-air gunnery practice area, Alaskan Air Command...

Code of Federal Regulations, 2011 CFR

2011-07-01

..., Alaska; air-to-air gunnery practice area, Alaskan Air Command, U.S. Air Force. 334.1300 Section 334.1300... gunnery practice area, Alaskan Air Command, U.S. Air Force. (a) The danger zone. A rhomboidal area... Air Command, U.S. Air Force, Anchorage, Alaska, or such agencies as he may designate. (Sec. 7, 40 Stat...

33 CFR 334.1300 - Blying Sound area, Gulf of Alaska, Alaska; air-to-air gunnery practice area, Alaskan Air Command...

Code of Federal Regulations, 2013 CFR

2013-07-01

..., Alaska; air-to-air gunnery practice area, Alaskan Air Command, U.S. Air Force. 334.1300 Section 334.1300... gunnery practice area, Alaskan Air Command, U.S. Air Force. (a) The danger zone. A rhomboidal area... Air Command, U.S. Air Force, Anchorage, Alaska, or such agencies as he may designate. (Sec. 7, 40 Stat...

33 CFR 334.1300 - Blying Sound area, Gulf of Alaska, Alaska; air-to-air gunnery practice area, Alaskan Air Command...

Code of Federal Regulations, 2012 CFR

2012-07-01

..., Alaska; air-to-air gunnery practice area, Alaskan Air Command, U.S. Air Force. 334.1300 Section 334.1300... gunnery practice area, Alaskan Air Command, U.S. Air Force. (a) The danger zone. A rhomboidal area... Air Command, U.S. Air Force, Anchorage, Alaska, or such agencies as he may designate. (Sec. 7, 40 Stat...

33 CFR 334.1300 - Blying Sound area, Gulf of Alaska, Alaska; air-to-air gunnery practice area, Alaskan Air Command...

Code of Federal Regulations, 2010 CFR

2010-07-01

..., Alaska; air-to-air gunnery practice area, Alaskan Air Command, U.S. Air Force. 334.1300 Section 334.1300... gunnery practice area, Alaskan Air Command, U.S. Air Force. (a) The danger zone. A rhomboidal area... Air Command, U.S. Air Force, Anchorage, Alaska, or such agencies as he may designate. (Sec. 7, 40 Stat...

Annotated Bibliography of the Air Force Human Resources Laboratory Technical Reports - 1979.

DTIC Science & Technology

1981-05-01

Force Human Resources Laboratory, March 1980. (Covers all AFHRL projects.) NTIS. This document provides the academic and industrial R&D community with...D-AI02 04𔃾 AIR FORCE HUMAN RESOURCES LAB BROOKS AF TX F/G 5/2 ANNOTATED BIBLIOGRAPHY OF THE AIR FORCE HUMAN RESOURCES LABORAT--ETC(U) MAY 81 E M...OF THE AIR FORCE HUMAN RESOURCES LABORATORY TECHNICAL REPORTS - 1979U M By M Esther M. Barlow A N TECHNICAL SERVICES DIVISION Brooks Air Force Base

A Study of Black Officer Candidate Attrition in the United States Air Force

DTIC Science & Technology

1993-09-01

concern among Air Force accession policy officials (Travers, 1992). Prior to 1973 the Air Force, as well as all other services, was under -represented in...Although the Air Force did not exist in 1940, its predecessor, the Army Air Corps, fell under this new policy. Thus, by the time the Air Force was made a...participation increased from 0.6 percent in 1942 to approximately 2 percent by 1973. However, blacks were 3till vastly under -represented in relation to both the

The United States Air Force Reserve Officer Training Corps: Looking to the Future

DTIC Science & Technology

1991-03-04

Brigadier General Robin G. Tornow Commandant, Air Force ROTC (Note 25) Over the years, Air Force ROTC has developed many strong points. Paramount among...maintaining a leaner and more capable force for the future. Brigadier General Robin G. Tornow Commandant, Air Force ROTC (Note 35) This alternative

Analysis of data on Air Force personnel collected at Lackland Air Force Base

DOT National Transportation Integrated Search

1969-10-01

In July, 1967, a report was published by the Personnel Research Laboratory, Lackland Air Force Base, entitled "An Attempt to Predict Automobile Accidents Among Air Force Personnnel". Approximately twelve thousand basic airmen and eleven hundred offic...

Around the Air Force: April 26 > U.S. Air Force > Article Display

Science.gov Websites

Speeches Archive Former AF Top 3 Viewpoints and Speeches Air Force Warrior Games 2017 Events 2018 Air Force Strategic Documents Desert Storm 25th Anniversary Observances DoD Warrior Games Portraits in Courage

Air Force officials name SARC of the year > U.S. Air Force > Article

Science.gov Websites

The Book Speeches Archive Former AF Top 3 Viewpoints and Speeches Air Force Warrior Games 2017 Events 2018 Air Force Strategic Documents Desert Storm 25th Anniversary Observances DoD Warrior Games

Remodeling Air Force Cyber Command and Control

DTIC Science & Technology

2017-10-10

AIR FORCE CYBERWORX REPORT: REMODELING AIR FORCE CYBER COMMAND & CONTROL COURSE DESIGN PROJECT CONDUCTED 5 Jan – 5 May 17 Produced...For the Air Force Cyber Command and Control (C2) Design Project, CyberWorx brought together 25 cadets from the United States Air Force Academy...warfighting based upon the findings of the design teams. Participants The design course was attended by a diverse group of civilians from industry

Handling Quality Requirements for Advanced Aircraft Design: Longitudinal Mode

DTIC Science & Technology

1979-08-01

phases of air -to- air combat, for example). This is far simpler than the general problem of control law definition. How- ever, the results of such...unlimited. Ali FORCE FUGHT DYNAMICS LABORATORYAIR FORCE WRIGHT AERONAUTICALLABORATORIES AIR FORCE SYSTEMS COMMANDI * WRIGHT-PATITERSON AIR FORCE BASE...not necessarily shared by the Air Force. Brian. W. VauVliet Project Engineer S Rorad0. Anderson, Chief Control Dynamics Branch Flight Control Division

Processing Multiyear Procurement (MYP) Submissions - A Handbook for Air Force Program Offices

DTIC Science & Technology

1985-05-01

Contracting and Manufacturing Policy; "Policy Letter 84-1l - Multiyear Contracting Guidance" Headquarters, United States Air Force, Washington, D.C...supplement to Air Force FAR Sup No. 17.191: as enclosed in Thomas E. Lloyd, Colonel, USAF, Assistant DCS/Contracting , and Manufacturing , "DCS...Contracting and Manufacturing Policy Letter 84-16, Multiyear Contracting Guidance." Headquarters, Air Force Systems Command, Andrew Air Force Base

Army and Air Force Unmanned Air Reconnaissance: Warrior and Hydra Navigating a Maze of Strategic Hedges

DTIC Science & Technology

2009-06-01

Chambliss; Colonel Michael Stickney; Colonel Eric Mathewson; Lieutenant Colonel Robert Kiebler; Lieutenant Colonel Kenneth Kilmurray; Lieutenant...16 Peter Layton , Group Captain, Royal Air Force, “Hedging Strategies, UCAVs, budgets, and improbable threats,” Armed Forces Journal...10 Colonel Eric Mathewson, US Air Force HAF/A2 DCS ISR, “Air Force ISR in a Changed World: ISR Transformation, the Importance

Air Force Leadership Diversity

DTIC Science & Technology

2017-04-06

AIR WAR COLLEGE AIR UNIVERSITY AIR FORCE LEADERSHIP DIVERSITY by G. Hall Sebren, Jr., Col, USAF A Research Report Submitted to the...both in HAF/A8 (Strategic Plans and Programs). iv Abstract The Air Force is not drawing upon its full talent pool for leadership in its...promotions boards, but the Air Force promotion system itself is not the problem. Leadership decisions to only allow officers selected for promotion from

Strength and Power Qualities Are Highly Associated With Punching Impact in Elite Amateur Boxers.

PubMed

Loturco, Irineu; Nakamura, Fabio Y; Artioli, Guilherme G; Kobal, Ronaldo; Kitamura, Katia; Cal Abad, Cesar C; Cruz, Igor F; Romano, Felipe; Pereira, Lucas A; Franchini, Emerson

2016-01-01

This study investigated the relationship between punching impact and selected strength and power variables in 15 amateur boxers from the Brazilian National Team (9 men and 6 women). Punching impact was assessed in the following conditions: 3 jabs starting from the standardized position, 3 crosses starting from the standardized position, 3 jabs starting from a self-selected position, and 3 crosses starting from a self-selected position. For punching tests, a force platform (1.02 × 0.76 m) covered by a body shield was mounted on the wall at a height of 1 m, perpendicular to the floor. The selected strength and power variables were vertical jump height (in squat jump and countermovement jump), mean propulsive power in the jump squat, bench press (BP), and bench throw, maximum isometric force in squat and BP, and rate of force development in the squat and BP. Sex and position main effects were observed, with higher impact for males compared with females (p ≤ 0.05) and the self-selected distance resulting in higher impact in the jab technique compared with the fixed distance (p ≤ 0.05). Finally, the correlations between strength/power variables and punching impact indices ranged between 0.67 and 0.85. Because of the strong associations between punching impact and strength/power variables (e.g., lower limb muscle power), this study provides important information for coaches to specifically design better training strategies to improve punching impact.

78 FR 77106 - U.S. Air Force Reminder Re: United Launch Alliance (ULA) Consent Order and Recent Change in...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-20

...: Headquarters Air Force, Deputy Under Secretary of the Air Force (Space). ACTION: Publicize Consent Order... Force (Space), as the Compliance Officer under the Federal Trade Commission (FTC) Decision and Order... Under Secretary of the Air Force (Space). This position is now held by Dr. Troy Meink. [[Page 77107...

USAF Summer Research Program - 1993 Graduate Student Research Program Final Reports, Volume 8, Phillips Laboratory

DTIC Science & Technology

1994-12-01

Research Program Phillips Laboratory Kirtland Air Force Base Albuquerque, New Mexico Sponsored by: Air ...Summer Research Program Phillips Laboratory Sponsored by. Air Force Office of Scientific Research Kirtland Air Force Base, Albuquerque, New Mexico...UNITED STATES AIR FORCE SUMMER RESEARCH PROGRAM -- 1993 SUMMER RESEARCH PROGRAM FINAL REPORTS VOLUME 8

Defense.gov Special Report: A Nation's Gratitude

Science.gov Websites

Deployments, 2003-2006 Baghdad, Ramadi Air Force Master Sgt. Jessica R. Coombs Air Force Master Sgt. Jessica R . Coombs 40th Expeditionary Support Squadron June 2011 - December 2011 Ali Air Base Indiana Army Master Sgt Multiple Deployments, 2004-2007 Fallujah, Ramadi Air Force Master Sgt. Jeremy G. Coombs Air Force Master

Back to the Future: Does History Support the Expeditionary Air Force Concept?

DTIC Science & Technology

2000-04-01

Operations Forces 550, “Agile Combat Support,” Mr. Ron Orr, USAF/IL, 2 Feb 00. 4 Davis, pg. 11. 5 Toulmin , H.A., Jr., Air Service, American...John A., “The Expeditionary Air Force Takes Shape,” Air Force Magazine, Vol. 80, No. 6, June 1997. Toulmin , H.A., Jr., Air Service, American

78 FR 14293 - Privacy Act of 1974; System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-05

.... SUPPLEMENTARY INFORMATION: The Department of the Air Force's notices for systems of records subject to the...: Delete entry and replace with ``10 U.S.C. 8013, Secretary of the Air Force; 10 U.S.C. 8032, The Air Staff... system interfaces. The interfaces are the Air Force Logistics Module, Air Force Military Personnel Data...

Air Force Research Laboratory, Edwards Air Force Base, CA

DTIC Science & Technology

2011-06-27

Air Force Research Laboratory (AFMC) AFRL /RZS 1 Ara Road Edwards AFB CA 93524-7013 AFRL -RZ-ED-VG-2011-269 9...SPONSORING / MONITORING AGENCY NAME(S) AND ADDRESS(ES) 10. SPONSOR/MONITOR’S ACRONYM(S) Air Force Research Laboratory (AFMC) AFRL /RZS 11. SPONSOR...Form 298 (Rev. 8-98) Prescribed by ANSI Std. 239.18 Air Force Research Laboratory Ed d Ai F B CA Col Mike Platt war s r orce

Intro & Basic R&D Overview for NRC RAP Administrator

DTIC Science & Technology

2011-07-13

Air Force Research Laboratory (AFMC) AFRL /RZS 5 Pollux Drive Edwards AFB CA...NUMBER (include area code) N/A Standard Form 298 (Rev. 8-98) Prescribed by ANSI Std. 239.18 1 Air Force Research Laboratory Edwards Air Force ...BOUNDARY 0 5 10 SCALE IN MILES HWY 395 ROSAMOND BLVD. MERCURY BLVD. R O C K ET S IT E R O A D EDWARDS AIR FORCE BASE Air Force Research

The United States Air Force in Korea: A Chronology, 1950-1953

DTIC Science & Technology

2000-01-01

War , the U.S. Air Force (USAF) Historian commissioned the Research Division, Air Force His- torical Research Agency (AFHRA), Maxwell Air Force Base...and aces. Finally, it attempts to summarize those USAF events in Korea that best illustrate the air war and the application of air power in the...sources, usually to confirm the most signifi- cant events of the air war in Korea. AFHRA historians or archivists who researched and wrote the monthly and

Simultaneous Soft Sensing of Tissue Contact Angle and Force for Millimeter-scale Medical Robots

PubMed Central

Arabagi, Veaceslav; Gosline, Andrew; Wood, Robert J.; Dupont, Pierre E.

2013-01-01

A novel robotic sensor is proposed to measure both the contact angle and the force acting between the tip of a surgical robot and soft tissue. The sensor is manufactured using a planar lithography process that generates microchannels that are subsequently filled with a conductive liquid. The planar geometry is then molded onto a hemispherical plastic scaffolding in a geometric configuration enabling estimation of the contact angle (angle between robot tip tangent and tissue surface normal) by the rotation of the sensor around its roll axis. Contact force can also be estimated by monitoring the changes in resistance in each microchannel. Bench top experimental results indicate that, on average, the sensor can estimate the angle of contact to within ±2° and the contact force to within ±5.3 g. PMID:24241496

78 FR 29123 - Proposed Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-17

... DEPARTMENT OF DEFENSE Department of the Air Force [Docket ID: USAF-2013-0018] Proposed Collection; Comment Request AGENCY: Department of Defense/Department of the Air Force/Headquarters, Air Force Safety... Act of 1995, the Department of the Air Force announces a proposed public information collection and...

Assessment of Regional Explosion Discriminants Using Data Sets of Unparalleled Spatial Sampling

DTIC Science & Technology

2012-10-31

Air Force Research Laboratory AFRL ...Final Report APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED. AIR FORCE RESEARCH LABORATORY Space Vehicles...Directorate 3550 Aberdeen Ave SE AIR FORCE MATERIEL COMMAND KIRTLAND AIR FORCE BASE, NM 87117-5776 Approved for public release; distribution

Critical Issues for Establishment of a Permanently-Occupied Lunar Base.

DTIC Science & Technology

1987-09-01

AIR FORCE ,. AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY 8 7 12 ’ -0). Wright-Patterson Air Force Base, Ohio IpDoTRiBUTON STATEMENT A Approved...the document are technically accurate, and no sensitive items, detrimental ideas, or deleterious information is contained therein. Furthermore, the...Faculty of the School of Systems and Logistics of the Air Force Institute of Technology Air University In Partial Fullfillment of the Requirements

Removal of volatile organic compounds (VOC`s) generated by Forest Product Industries using biofiltration technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gilliland, G.A.; Ramaswami, R.D.; Patel, D.N.

1995-12-31

Implementation of Clean Air Act Title V and the increasing environmental concerns of the public are imposing greater demands on the Forest Product industries to control their air emissions. As implementation of this Clean Air Act has begun, Forest Product Industries are recognizing the overall lack of historical emissions data, emissions testing information and knowledge of the economics of emission control technologies needed to reduce emissions. This study was undertaken to evaluate the types of VOC`s produced in drying and pressing wood composites, and determine how effective biofiltration technology could be used in reducing the levels of these products beforemore » they are released into the air. More specifically, the experiments were conducted to isolate microorganisms capable of degrading VOC`s and determine their biodegradation rates using bench scale biofilters.« less

Effects of 5 Weeks of Bench Press Training on Muscle Synergies: A Randomized Controlled Study.

PubMed

Kristiansen, Mathias; Samani, Afshin; Madeleine, Pascal; Hansen, Ernst A

2016-07-01

Kristiansen, M, Samani, A, Madeleine, P, and Hansen, EA. Effects of 5 weeks of bench press training on muscle synergies: A randomized controlled study. J Strength Cond Res 30(7): 1948-1959, 2016-The ability to perform forceful muscle contractions has important implications in sports performance and in activities of daily living. However, there is a lack of knowledge on adaptations in intermuscular coordination after strength training. The purpose of this study was therefore to assess muscle synergies before and after 5 weeks of bench press training. Thirty untrained male subjects were randomly allocated to a training group (TRA) or a control group (CON). After the pretest, TRA completed 5 weeks of bench press training, before completing a posttest, whereas subjects in CON continued their normal life. During test sessions, surface electromyography (EMG) was recorded from 13 different muscles. Muscle synergies were extracted from EMG data using nonnegative matrix factorization. To evaluate differences between pretest and posttest, we performed a cross-correlation analysis and a cross-validation analysis, in which the synergy components extracted in the pretest session were recomputed, using the fixed synergy components from the posttest session. Two muscle synergies accounted for 90% of the total variance and reflected the concentric and eccentric phase, respectively. TRA significantly increased 3 repetition maximum in bench press with 19.0% (25th; 75th percentile, 10.3%; 21.7%) (p < 0.001), whereas no change occurred in CON. No significant differences were observed in synergy components between groups. However, decreases in correlation values for intragroup comparisons in TRA may suggest that the synergy components changed, whereas this was not the case in CON. Strength and conditioning professionals may consider monitoring changes in muscle synergies in training and rehabilitation programs as a way to benchmark changes in intermuscular coordination.

Predicting the Maximum Dynamic Strength in Bench Press: The High Precision of the Bar Velocity Approach.

PubMed

Loturco, Irineu; Kobal, Ronaldo; Moraes, José E; Kitamura, Katia; Cal Abad, César C; Pereira, Lucas A; Nakamura, Fábio Y

2017-04-01

Loturco, I, Kobal, R, Moraes, JE, Kitamura, K, Cal Abad, CC, Pereira, LA, and Nakamura, FY. Predicting the maximum dynamic strength in bench press: the high precision of the bar velocity approach. J Strength Cond Res 31(4): 1127-1131, 2017-The aim of this study was to determine the force-velocity relationship and test the possibility of determining the 1 repetition maximum (1RM) in "free weight" and Smith machine bench presses. Thirty-six male top-level athletes from 3 different sports were submitted to a standardized 1RM bench press assessment (free weight or Smith machine, in randomized order), following standard procedures encompassing lifts performed at 40-100% of 1RM. The mean propulsive velocity (MPV) was measured in all attempts. A linear regression was performed to establish the relationships between bar velocities and 1RM percentages. The actual and predicted 1RM for each exercise were compared using a paired t-test. Although the Smith machine 1RM was higher (10% difference) than the free weight 1RM, in both cases the actual and predicted values did not differ. In addition, the linear relationship between MPV and percentage of 1RM (coefficient of determination ≥95%) allow determination of training intensity based on the bar velocity. The linear relationships between the MPVs and the relative percentages of 1RM throughout the entire range of loads enable coaches to use the MPV to accurately monitor their athletes on a daily basis and accurately determine their actual 1RM without the need to perform standard maximum dynamic strength assessments.

Changes in Maximal Strength, Velocity, and Power After 8 Weeks of Training With Pneumatic or Free Weight Resistance.

PubMed

Frost, David M; Bronson, Stefanie; Cronin, John B; Newton, Robert U

2016-04-01

Because free weight (FW) and pneumatic (PN) resistance are characterized by different inertial properties, training with either resistance could afford unique strength, velocity, and power adaptations. Eighteen resistance-trained men completed baseline tests to determine their FW and PN bench press 1 repetition maximum (1RM). During the FW session, 4 explosive repetitions were performed at loads of 15, 30, 45, 60, 75, and 90% 1RM to assess force, velocity, and power. Participants were then assigned to a FW or PN training group, which involved three 90-minute sessions per week for 8 weeks. Both intervention groups completed identical periodized programs with the exception of the resistance used to perform all bench press movements. Free weight participants significantly increased their FW and PN 1RM (10.4 and 9.4%), and maximum (any load) force (9.8%), velocity (11.6%), and power (22.5%). Pneumatic-trained participants also exhibited increases in FW and PN 1RM (11.6 and 17.5%), and maximum force (8.4%), velocity (13.6%), and power (33.4%). Both interventions improved peak barbell velocity at loads of 15 and 30% 1RM; however, only the PN-trained individuals displayed improvements in peak force and power at these same loads. Training with PN resistance may offer advantages if attempting to improve power at lighter relative loads by affording an opportunity to consistently achieve higher accelerations and velocities (F = ma), in comparison with FW. Exploiting the inertial properties of the resistance, whether mass, elastic or PN, could afford an opportunity to develop mixed-method training strategies and/or elicit unique neuromuscular adaptations to suit the specific needs of athletes from sports characterized by varying demands.

The Neuromuscular Qualities of Higher- and Lower-Level Mixed-Martial-Arts Competitors.

PubMed

James, Lachlan P; Beckman, Emma M; Kelly, Vincent G; Haff, G Gregory

2017-05-01

To determine whether the maximal strength, impulse, and power characteristics of competitive mixed-martial-arts (MMA) athletes differ according to competition level. Twenty-nine male semiprofessional and amateur MMA competitors were stratified into either higher-level (HL) or lower-level (LL) performers on the basis of competition grade and success. The 1-repetition-maximum (1RM) squat was used to assess lower-body dynamic strength, and a spectrum of impulse, power, force, and velocity variables were evaluated during an incremental-load jump squat. In addition, participants performed an isometric midthigh pull (IMTP) and 1RM bench press to determine whole-body isometric force and upper-body dynamic strength capabilities, respectively. All force and power variables were expressed relative to body mass (BM). The HL competitors produced significantly superior values across a multitude of measures. These included 1RM squat strength (1.84 ± 0.23 vs 1.56 ± 0.24 kg BM; P = .003), in addition to performance in the incremental-load jump squat that revealed greater peak power (P = .005-.002), force (P = .002-.004), and velocity (P = .002-.03) at each load. Higher measures of impulse (P = .01-.04) were noted in a number of conditions. Average power (P = .002-.02) and velocity (P = .01-.04) at all loads in addition to a series of rate-dependent measures were also superior in the HL group (P = .005-.02). The HL competitors' 1RM bench-press values approached significantly greater levels (P = .056) than the LL group's, but IMTP performance did not differ between groups. Maximal lower-body neuromuscular capabilities are key attributes distinguishing HL from LL MMA competitors. This information can be used to inform evidenced-based training and performance-monitoring practices.

77 FR 55465 - US Air Force Exclusive Patent License

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-10

...: Air Force Research Laboratory Information Directorate, Rome, New York, Department of the Air Force.... Written objections should be sent to: Air Force Research Laboratory, Office of the Staff Judge Advocate, AFRL/RIJ, 26 Electronic Parkway, Rome, New York 13441-4514. Telephone: (315) 330-2087; Facsimile (315...

78 FR 39004 - Federal Property Suitable as Facilities To Assist the Homeless

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-28

... following addresses: AIR FORCE: Mr. Robert Moore, Air Force Real Property Agency, 2261 Hughes Avenue, Suite... 304 Cheyenne Mountain AFS Colorado Springs CO 80914 Landholding Agency: Air Force Property Number... Agency: Air Force Property Number: 18201320042 Status: Underutilized Directions: 1478, 1479, 1480,1482...

32 CFR 855.1 - Policy.

Code of Federal Regulations, 2013 CFR

2013-07-01

... of Air Force airfields in foreign countries will be subject to US Federal laws and regulations that... Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL AIRCRAFT USE OF UNITED STATES AIR FORCE AIRFIELDS General Provisions § 855.1 Policy. The Air Force establishes and uses its...

32 CFR 855.1 - Policy.

Code of Federal Regulations, 2011 CFR

2011-07-01

... of Air Force airfields in foreign countries will be subject to US Federal laws and regulations that... Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL AIRCRAFT USE OF UNITED STATES AIR FORCE AIRFIELDS General Provisions § 855.1 Policy. The Air Force establishes and uses its...

32 CFR 855.1 - Policy.

Code of Federal Regulations, 2012 CFR

2012-07-01

... of Air Force airfields in foreign countries will be subject to US Federal laws and regulations that... Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL AIRCRAFT USE OF UNITED STATES AIR FORCE AIRFIELDS General Provisions § 855.1 Policy. The Air Force establishes and uses its...

32 CFR 855.1 - Policy.

Code of Federal Regulations, 2014 CFR

2014-07-01

... of Air Force airfields in foreign countries will be subject to US Federal laws and regulations that... Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL AIRCRAFT USE OF UNITED STATES AIR FORCE AIRFIELDS General Provisions § 855.1 Policy. The Air Force establishes and uses its...

77 FR 16213 - Air University Board of Visitors Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-20

... DEPARTMENT OF DEFENSE Department of the Air Force Air University Board of Visitors Meeting ACTION: Notice of Meeting Cancellation of the Air Force Institute of Technology (AFIT) Subcommittee of the Air.... 552b, as amended), and 41 CFR 102-3.150, the Department of Defense announced that the Air Force...

Air Force Journal of Logistics. Volume 29, Number 1, Spring 2005

DTIC Science & Technology

2005-01-01

Air Force, is necessary in the transaction of the public business as required by the law of the department. The Secretary of the Air Force approved the...reengineer Air Force Materiel Command (AFMC) progress and introduce a supplier scorecard. sustainment business processes. This transformation effort, AFMC...empowerment." company. I think one of the things we’re seeing in American However, the business side of the Air Force consistently has business is a resurgence

77 FR 64493 - Office of the Secretary of the Air Force Acceptance of Group Application Under Public Law 95-202...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-10-22

... DEPARTMENT OF DEFENSE Department of the Air Force Office of the Secretary of the Air Force... AGENCY: The United States Air Force, DOD. ACTION: Notice. SUMMARY: Under the provisions of Section 401... group should be considered active military service to the Armed Forces of the United States are...

News

Science.gov Websites

Search News Comments Updated 1 2 3 4 5 6 7 8 9 10 ... 188 Default Air Force Logo Air Force transitions to Field from May 2-4. (U.S. Air Force photo by Staff Sgt. Ryan Conroy) SECAF visits Hurlburt for AFSOC mission immersion Secretary of the Air Force Heather Wilson visited Hurlburt Field May 2-4 for her Air

Reusable Military Launch Systems (RMLS)

DTIC Science & Technology

2008-02-01

described on inside pages STINFO COPY AIR FORCE RESEARCH LABORATORY AIR VEHICLES DIRECTORATE WRIGHT-PATTERSON AIR FORCE BASE, OH 45433...7542 AIR FORCE MATERIEL COMMAND UNITED STATES AIR FORCE NOTICE AND SIGNATURE PAGE Using Government drawings, specifications, or other data...DOCUMENTATION PAGE Form Approved OMB No. 0704-0188 The public reporting burden for this collection of information is estimated to average 1 hour per response

32 CFR 855.22 - Air Force procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 6 2012-07-01 2012-07-01 false Air Force procedures. 855.22 Section 855.22 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL AIRCRAFT USE... is located. AFI 13-201, Air Force Airspace Management, 8 lists the AFREPs and their addresses. The...

32 CFR 855.22 - Air Force procedures.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 6 2014-07-01 2014-07-01 false Air Force procedures. 855.22 Section 855.22 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL AIRCRAFT USE... is located. AFI 13-201, Air Force Airspace Management, 8 lists the AFREPs and their addresses. The...

Helical Explosive Flux Compression Generator Research at the Air Force Research Laboratory

DTIC Science & Technology

1999-06-01

Air Force Research Laboratory Kirtland AFB...ORGANIZATION NAME(S) AND ADDRESS(ES) Directed Energy Directorate, Air Force Research Laboratory Kirtland AFB, NM 8. PERFORMING ORGANIZATION REPORT...in support of the Air Force Research Laboratory ( AFRL ) explosive pulsed power program. These include circuit codes such as Microcap and

32 CFR 631.15 - Air Force policy.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 4 2014-07-01 2013-07-01 true Air Force policy. 631.15 Section 631.15 National...-Installation Operations (Military Patrols and Investigative Activities) and Policy § 631.15 Air Force policy. (a) Airmen, military and/or Department of the Air Force Civilian (DAFC) police performing off...

32 CFR 631.15 - Air Force policy.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 4 2013-07-01 2013-07-01 false Air Force policy. 631.15 Section 631.15 National...-Installation Operations (Military Patrols and Investigative Activities) and Policy § 631.15 Air Force policy. (a) Airmen, military and/or Department of the Air Force Civilian (DAFC) police performing off...

77 FR 33202 - Department of the Air Force

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-05

... DEPARTMENT OF DEFENSE Department of the Air Force Corrected Intent To Grant a Partially Exclusive Patent License AGENCY: The United States Air Force, DoD. SUMMARY: This notice replaces the one published... implements Public Law 96- 517, as amended; the Department of the Air Force announces its intention to grant...

Environmental Assessment: General Plan-Based Environmental Impact Analysis Process, Laughlin Air Force Base

DTIC Science & Technology

2007-05-01

BASED ENVIROMENTAL IMPACT ANALYSIS PROCESS LAUGHLIN AIR FORCE BASE, TEXAS AGENCY: 47th Flying Training Wing (FTW), Laughlin Air Force Base (AFB), Texas...8217\\ \\ \\ \\ \\\\ \\ ~ >(- \\ , ~ AOC01 \\ PS018 / WP002 \\ DP008 // WP006 \\ ~ ,/ ’----- -----·-------------~--/·/ LAUGHLIN AIR FORCE BASE ENVIROMENTAL RESTORATION

32 CFR 631.15 - Air Force policy.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 4 2011-07-01 2011-07-01 false Air Force policy. 631.15 Section 631.15 National...-Installation Operations (Military Patrols and Investigative Activities) and Policy § 631.15 Air Force policy. (a) Airmen, military and/or Department of the Air Force Civilian (DAFC) police performing off...

Inspector General, DOD, Oversight of the Air Force Audit Agency Audit of the FY 1999 Air Force General Fund Financial Statements

DTIC Science & Technology

2000-02-14

Consolidated Financial Statements . Our objective was to determine the accuracy and completeness of the Air Force Audit Agency audit of the FY 1999 Air Force General Fund financial statements. See Appendix A for a discussion of the audit

32 CFR 644.136 - Leasing guidelines.

Code of Federal Regulations, 2014 CFR

2014-07-01

... with present procedures for military leases. (2) Air Force. Upon receipt of a lease request approved by Headquarters, U.S. Air Force, or an Air Force major command, the appropriate Division or District Engineer will... Guard requirements will be transmitted to DAEN-REA-L through Headquarters, U.S. Air Force. (i) Upon...

32 CFR 644.136 - Leasing guidelines.

Code of Federal Regulations, 2011 CFR

2011-07-01

... with present procedures for military leases. (2) Air Force. Upon receipt of a lease request approved by Headquarters, U.S. Air Force, or an Air Force major command, the appropriate Division or District Engineer will... Guard requirements will be transmitted to DAEN-REA-L through Headquarters, U.S. Air Force. (i) Upon...

32 CFR 644.136 - Leasing guidelines.

Code of Federal Regulations, 2013 CFR

2013-07-01

... with present procedures for military leases. (2) Air Force. Upon receipt of a lease request approved by Headquarters, U.S. Air Force, or an Air Force major command, the appropriate Division or District Engineer will... Guard requirements will be transmitted to DAEN-REA-L through Headquarters, U.S. Air Force. (i) Upon...

32 CFR 644.136 - Leasing guidelines.

Code of Federal Regulations, 2012 CFR

2012-07-01

... with present procedures for military leases. (2) Air Force. Upon receipt of a lease request approved by Headquarters, U.S. Air Force, or an Air Force major command, the appropriate Division or District Engineer will... Guard requirements will be transmitted to DAEN-REA-L through Headquarters, U.S. Air Force. (i) Upon...

32 CFR 644.136 - Leasing guidelines.

Code of Federal Regulations, 2010 CFR

2010-07-01

... with present procedures for military leases. (2) Air Force. Upon receipt of a lease request approved by Headquarters, U.S. Air Force, or an Air Force major command, the appropriate Division or District Engineer will... Guard requirements will be transmitted to DAEN-REA-L through Headquarters, U.S. Air Force. (i) Upon...

32 CFR 806b.1 - Summary of revisions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... for the Air Force Privacy Program from Air Force Communications and Information Center to the Air Force Chief Information Officer; prescribes Air Force Visual Aid 33-276, Privacy Act Label as optional; adds the E-Gov Act of 2002 requirement for a Privacy Impact Assessment for all information systems that...

32 CFR 806b.1 - Summary of revisions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... for the Air Force Privacy Program from Air Force Communications and Information Center to the Air Force Chief Information Officer; prescribes Air Force Visual Aid 33-276, Privacy Act Label as optional; adds the E-Gov Act of 2002 requirement for a Privacy Impact Assessment for all information systems that...

32 CFR 806b.1 - Summary of revisions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... for the Air Force Privacy Program from Air Force Communications and Information Center to the Air Force Chief Information Officer; prescribes Air Force Visual Aid 33-276, Privacy Act Label as optional; adds the E-Gov Act of 2002 requirement for a Privacy Impact Assessment for all information systems that...

Estimation of longitudinal force, lateral vehicle speed and yaw rate for four-wheel independent driven electric vehicles

NASA Astrophysics Data System (ADS)

Chen, Te; Xu, Xing; Chen, Long; Jiang, Haobing; Cai, Yingfeng; Li, Yong

2018-02-01

Accurate estimation of longitudinal force, lateral vehicle speed and yaw rate is of great significance to torque allocation and stability control for four-wheel independent driven electric vehicle (4WID-EVs). A fusion method is proposed to estimate the longitudinal force, lateral vehicle speed and yaw rate for 4WID-EVs. The electric driving wheel model (EDWM) is introduced into the longitudinal force estimation, the longitudinal force observer (LFO) is designed firstly based on the adaptive high-order sliding mode observer (HSMO), and the convergence of LFO is analyzed and proved. Based on the estimated longitudinal force, an estimation strategy is then presented in which the strong tracking filter (STF) is used to estimate lateral vehicle speed and yaw rate simultaneously. Finally, co-simulation via Carsim and Matlab/Simulink is carried out to demonstrate the effectiveness of the proposed method. The performance of LFO in practice is verified by the experiment on chassis dynamometer bench.

Methods for Evaluating the Performance and Human Stress-Factors of Percussive Riveting

NASA Astrophysics Data System (ADS)

Ahn, Jonathan Y.

The aerospace industry automates portions of their manufacturing and assembly processes. However, mechanics still remain vital to production, especially in areas where automated machines cannot fit, or have yet to match the quality of human craftsmanship. One such task is percussive riveting. Because percussive riveting is associated with a high risk of injury, these tool must be certified prior to release. The major contribution of this thesis is to develop a test bench capable of percussive riveting for ergonomic evaluation purposes. The major issues investigated are: (i) automate the tool evaluation method to be repeatable; (ii) demonstrate use of displacement and force sensors; and (iii) correlate performance and risk exposure of percussive tools. A test bench equipped with servomotors and pneumatic cylinders to control xyz-position of a rivet gun and bucking bar simultaneously, is used to explore this evaluation approach.

Development of circumferential seal for helicopter transmissions: Results of bench and flight tests

NASA Technical Reports Server (NTRS)

Strom, T. N.; Ludwig, L. P.

1975-01-01

A modified circumferential segmented ring seal was designed for direct replacement of a helicopter transmission elastomeric lip seal operating on a shaft diameter of 13.91 centimeters (5.481 in.) at sliding velocities to 52.48 m/sec (10 330 ft/min). The modifications involved the garter spring tension, shaft roundness, seal housing flatness, and pumping grooves to inhibit leakage. Operation of the seals in bench tests under simulated helicopter transmission conditions revealed that the seal leakage rate was within acceptable limits and that the wear rate was negligible. The low leakage and wear rates were confirmed in flight tests of 600 and 175 hours (sliding speed, 48.11 m/sec (9470 ft/min)). An additional 200 hours of air worthiness qualification testing (aircraft tie down) demonstrated that the seal can operate at the advanced sliding conditions of 52.48 m/sec (10 330 ft/min).

Formulation and evaluation of C-Ether fluids as lubricants useful to 260 C. [air breathing engines

NASA Technical Reports Server (NTRS)

Clark, F. S.; Miller, D. R.

1980-01-01

Three base stocks were evaluated in bench and bearing tests to determine their suitability for use at bulk oil temperatures (BOT) from -40 C to +260 C. A polyol ester gave good bearing tests at a bulk temperature of 218 C, but only a partially successful run at 274 C. These results bracket the fluid's maximum operating temperature between these values. An extensive screening program selected lubrication additives for a C-ether (modified polyphenyl ether) base stock. One formulation lubricated a bearing for 111 hours at 274 C (BOT), but this fluid gave many deposit related problems. Other C-ether blends produced cage wear or fatigue failures. Studies of a third fluid, a C-ether/disiloxane blend, consisted of bench oxidation and lubrication tests. These showed that some additives react differently in the blend than in pure C-ethers.

Job Dissatisfaction among Air Force Clinical Nurses: Causes and Ways to Change It.

DTIC Science & Technology

1988-01-01

44%) of nurses planning an L Air Force career (14:--). Recognizing job satisfaction can be a major deciding factor in choosing an Air Force career ... burnout and searched for ideas on how to improve clinical nursing in the Air Force. improving job satisfaction in nursing today is a hot topic and...clinical nurses are falling victim to " burnout " syndrome, which in turn is affecting their job satisfaction . Air Force clinical inpatient nurses are managing

Metallurgical Characterization of Aluminum Powder Consolidation.

DTIC Science & Technology

1984-09-01

implied, of the Air Force * Office of Scientific Research of the U.S. Government. LaJ DT[ Prepared for: MR 2 8 M985 UNITED STATES AIR FORCE Air Force...Office of Scientific ResearchE Boiling Air Force Base, DC 20332 85 03 12 083 UNCLASSIFIED SECURITY CLASSIFICATION OF THIS PAGE (When Dota Entered). REPORT...Corporation P.O. Box 516 St. Louis, MO 63166 WiOL r - O * 11. CONTROLLING OFFICE NAME AND ADDRESS 12. REPORT DATE Air Force Office of Scientific

Environmental Assessment for the Replacement of a Vehicle Wash Rack, Travis Air Force Base, California

DTIC Science & Technology

2005-04-01

meet state and U.S. Air Force (Air Force) environmental requirements for the use of cleaning products and washing systems; comply with Air Force and...and O/WSs • Use environmentally compliant cleaning products and wash systems • Be equipped with a credit card reader or similar device, to document... cleaning products and washing systems, including operating a covered O/WS within design capacity limits • Comply with Air Force and Department of

Strategic Defense Initiative Demonstration/Validation Program: Environmental Assessments Summary

DTIC Science & Technology

1987-08-01

TECHNOLOGY TESTS BY FACILITY TECHNOLOGY FACILITY BSTS SSTS GSTS SBI ERIS BM/C 3 Alabama Advanced Research Center A,S,C * California Edwards Air Force Base...Alabama - Advanced Research Center o California - Edwards Air Force Base o Florida - Eglin Air Force Base Kennedy Space Center o Maryland - Harry Diamond...BSTS SSTS GSTS SBI ERIS BM/C 3 Alabama Advanced Research Center A,S,C * California Edwards Air Force Base C Vandenberg Air Force Base/ F (1) F (2) F( 2

Environmental Assessment Proposed Demolition Plan Hill Air Force Base, Utah

DTIC Science & Technology

2010-04-01

1204, Arlington VA 22202-4302. Respondents should be aware that notwithstanding any other provision of law , no person shall be subject to a penalty...Demolition Plan Hill Air Force Base, Utah 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR( S ) 5d. PROJECT NUMBER 5e. TASK...NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME( S ) AND ADDRESS(ES) United States Air Force - Air Force Material Command,Hill Air Force

Air Force UAV’s: The Secret History

DTIC Science & Technology

2010-07-01

iA Mitchell Institute Study i Air Force UAVs The Secret History A Mitchell Institute Study July 2010 By Thomas P. Ehrhard Report Documentation Page...DATES COVERED 00-00-2010 to 00-00-2010 4. TITLE AND SUBTITLE Air Force UAVs The Secret History 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c... The Secret History 2 Air Force UAVs: The Secret History2 air Force uaVs: The secret history Has any airplane in the past decade captured the public

The Chinese Communist Armed Forces.

DTIC Science & Technology

1974-01-01

tepriorcosn \\ MAR 1 3 1981 C ~) AIR UNIVERSITY -4 MAXWELL AIR FORCE BASE, ALABAMA I z AU-I I "-- ’The Chinese Communist Armed Forces. Kenneth R. Whiting...AO-A096 28𔃾 DEPARTMENT OF STATE WASHINGTON DC OFFICE OF EXTERNAL--ETC F/6 S/ THE CH INESE C OMMUNIST ARMED FORCES. (U) vsif k.1974 K R WHITING FAR...1974 Directorate of Documentary Research Air University Institute for Professional Development Maxwell Air Force Base, Alabama "/" I;-) K II AIR

Monte Carlo Bayesian System Reliability and MTBF-Confidence Assessment, II. Volume 2. SPARCS-2 Users Manual

DTIC Science & Technology

1978-03-01

1977 Approved for public release; distribution unlimited. AIR FORCE FLIGHT DYNAMICS LABORATORY AIR FORCE WRIGHT AERONAUTICAL LABORATORIES AIR FORCE...SYSTEMS COMMAND WRIGHT-PATTERSON AIR FORCE BASE, OHIO 45433 NOTI CE When Gove~inme~nt d’tawi~ngz, .6pe~c4Lcatiton, ct o-theAi da~ta cute -6e~d Joit any... AIR FORCE/56780/6 June 1978 -450 Unclassified SECURITY CLASSIFICATION OF THIS PAGE ("hen Date ýntered) READ INSTRUCTIONSREPORT DOCUMENTATION PAGE

Combat Squadrons of the Air Force, World War II,

DTIC Science & Technology

1982-01-01

1952. Inactivated on 1 Jul 1957. Redes- of a paddle wheel river boat, Air Force ignated 7o2d Troop Carrier Squadron blue, the windows lighted Air Force ...782d Bombard- hitched to a red wagon with wheels red, ment Squadron (Heavy) on 19 May hub yellow, tires and axles black, the 1943. Activated on 1 Aug...AD-A128 026 COMBAT SQUADRONS OF TOE AIR FORCE WORLD WAR IU) 1OFFICEOF AIR FORCE HISTORY WASHINGTON DC M MAURER UNCLASSIFIED F/G 15/7 NL

Stress Analysis of Aircraft Tires. Volume I. Analytical Formulation

DTIC Science & Technology

1976-02-01

Dynamics Laboratories, AFFDL/ FEM , WPAFB, Ohio 45433. 3C S AIR FORCE FLIGHT DYNAMICS LABORATORY AIR FORCE WRIGHT AERONAUTICAL LABORATORIES AIR FORCE...Dynamics Laboratories, AFFDL/ FEM , WPAFB, Ohio 45433. IT niSTRin^TiON STATEMENT (al th» mbilrmtl ••(•••« In Black 20, It altltrmtl Inm Rapart; -D-D-G...Patterson Air Force Base, Dayton, Ohio. Mr. J. R. Hampton (AFFDL/ FEM ) was the technical monitor for the Air Force. This report covers the research

78 FR 4134 - Notice of Intent To Prepare An Environmental Impact Statement (EIS) On the Proposal To Relocate...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-18

... Proposal To Relocate the 18th Aggressor Squadron From Eielson Air Force Base (EAFB), Alaska to Joint Base... Eielson AFB, AK AGENCY: Pacific Air Forces, United States Air Force, DOD. ACTION: Notice of Intent... Provisions of NEPA (40 CFR parts 1500-1508), and Air Force policy and procedures (32 CFR part 989), the Air...

Environmental Assessment Deicer Recovery at Grand Forks AFB, North Dakota

DTIC Science & Technology

2004-12-15

Air Force Base (AFB), North Dakota. Contacts: 319 CES/CEVA 525 Tuskegee Airmen Boulevard (Blvd) Grand Forks AFB, ND...ACRONYMS, ABBREVIATIONS, AND TERMS AAM Annual Arithmetic Mean ACM Asbestos Containing Material AFB Air Force Base AFI Air Force Instruction AICUZ...meter 10 GFAFB Grand Forks Air Force Base HAP Hazardous Air Pollutants hr Hour H2S Hydrogen Sulfide IRP Installation Restoration

Rebalancing the Air Force: A Comprehensive Solution

DTIC Science & Technology

2011-02-16

the consequences can be significant. High Tempo (Figure 4) Lt Gen Charles E. Stenner , Jr., Chief of the Air Force Reserve, stated while...29 January 2010. 14 Lt Gen Charles E. Stenner Jr., Chief of the Air Force Reserve, ―Total Force Policy 21: A 21 st Century Framework for...Military Force Mix Decisions,‖ White Paper, 15 July 2010. 15 Lt Gen Charles E. Stenner Jr., Chief of the Air Force Reserve, ―Testimony Before the House

Aircraft Brake Systems Testing Handbook.

DTIC Science & Technology

1981-05-01

distribution is unlimited. AIR FORCE FLIGHT TEST CENTER EDWARDS AIR FORCE BASE , CALIFORNIA AIR FORCE SYSTEMS COMMAND UNITED STATES AIR FORCE A This handbook... Base , California 93523. This handbook has been reviewed and cleared for open publication and/or public release by the AFFTC Office of Public Affairs in...Force lbs Ft Engine Thrust lbs F vrt Vertical Force acting on the tire at the qround lbs 9 Acceleration due to gravity 32.17 ft/sec 2 h Distance

Desert Talons: Historical Perspectives and Implications of Air Policing in the Middle East

DTIC Science & Technology

2009-04-01

predominant role in support of a smaller ground force has historical precedent. During the 1920s, the Royal Air Forces (RAF) air control method adhered...the Royal Air Force’s (RAF) air control method adhered to the concepts of the inverted blockade, minimum force, precision targeting, and force...owing to its process of rapid communications, Air Methods are, in short, the reverse of the old punitive column. Our policy is one of prevention

78 FR 49729 - Takes of Marine Mammals Incidental to Specified Activities; U.S. Air Force Launches, Aircraft and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-15

... Marine Mammals Incidental to Specified Activities; U.S. Air Force Launches, Aircraft and Helicopter Operations, and Harbor Activities Related to Launch Vehicles From Vandenberg Air Force Base (VAFB... comments and information. SUMMARY: NMFS has received a request from the U.S. Air Force (USAF) for...

77 FR 66595 - U.S. Air Force Broadcast of Consent Order, and Determination of Interest Level for a United...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-06

...: Headquarters Air Force, Deputy Under Secretary of the Air Force (Space). ACTION: Publicize Consent Order, and... solicitation issuance. The Deputy Under Secretary of the Air Force (Space), as the Compliance Officer under the...) ULA afford all space vehicle manufacturers [[Page 66596

Forecasting Foreign Currency Exchange Rates for Air Force Budgeting

DTIC Science & Technology

2015-03-26

FORECASTING FOREIGN CURRENCY EXCHANGE RATES FOR AIR FORCE BUDGETING THESIS MARCH 2015...States. AFIT-ENV-MS-15-M-178 FORECASTING FOREIGN CURRENCY EXCHANGE RATES FOR AIR FORCE BUDGETING THESIS Presented to the Faculty...FORECASTING FOREIGN CURRENCY EXCHANGE RATES FOR AIR FORCE BUDGETING Nicholas R. Gardner, BS Captain, USAF Committee Membership: Lt Col Jonathan

32 CFR 855.7 - Conditions for use of Air Force airfields.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Conditions for use of Air Force airfields. 855.7 Section 855.7 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL AIRCRAFT USE OF UNITED STATES AIR FORCE AIRFIELDS Civil Aircraft Landing Permits § 855.7...

32 CFR 865.5 - Decision of the Secretary of the Air Force.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Decision of the Secretary of the Air Force. 865.5 Section 865.5 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE ORGANIZATION AND MISSION-GENERAL PERSONNEL REVIEW BOARDS Air Force Board for Correction of Military Records...

32 CFR 989.7 - Requests from Non-Air Force agencies or entities.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Requests from Non-Air Force agencies or entities. 989.7 Section 989.7 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE ENVIRONMENTAL PROTECTION ENVIRONMENTAL IMPACT ANALYSIS PROCESS (EIAP) § 989.7 Requests from Non-Air Force...

32 CFR 644.516 - Clearance of Air Force lands.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 4 2010-07-01 2010-07-01 true Clearance of Air Force lands. 644.516 Section 644... Excess Land and Improvements § 644.516 Clearance of Air Force lands. The Chief of Engineers has no responsibility for inspecting or clearing excess Air Force land of explosives or chemical/biological contaminants...

32 CFR 855.7 - Conditions for use of Air Force airfields.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 6 2013-07-01 2013-07-01 false Conditions for use of Air Force airfields. 855.7 Section 855.7 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL AIRCRAFT USE OF UNITED STATES AIR FORCE AIRFIELDS Civil Aircraft Landing Permits § 855.7...

32 CFR 855.7 - Conditions for use of Air Force airfields.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 32 National Defense 6 2014-07-01 2014-07-01 false Conditions for use of Air Force airfields. 855.7 Section 855.7 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL AIRCRAFT USE OF UNITED STATES AIR FORCE AIRFIELDS Civil Aircraft Landing Permits § 855.7...

32 CFR 855.7 - Conditions for use of Air Force airfields.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 6 2012-07-01 2012-07-01 false Conditions for use of Air Force airfields. 855.7 Section 855.7 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL AIRCRAFT USE OF UNITED STATES AIR FORCE AIRFIELDS Civil Aircraft Landing Permits § 855.7...

32 CFR 855.7 - Conditions for use of Air Force airfields.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 6 2011-07-01 2011-07-01 false Conditions for use of Air Force airfields. 855.7 Section 855.7 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL AIRCRAFT USE OF UNITED STATES AIR FORCE AIRFIELDS Civil Aircraft Landing Permits § 855.7...

Newsroom

Science.gov Websites

from Air Force Gen. Lori Robinson during a ceremony held at Peterson Air Force Base today. May 24, 2018 Gen. O'Shaughnessy assumes command of NORAD, USNORTHCOM Peterson Air Force Base, Colo. - Air Force Gen terminal Sept. 22, 2017 at Joint Base San Antonio-Kelly Field. The cargo was being staged at the Federal

Defense.gov - Dignity, Honor, Respect - For the Fallen

Science.gov Websites

combat operation passes through Dover Air Force Base, Del. The responsibility, and honor, of preparing Operations Center. Stories Dignified Transfer Pays Tribute to Fallen DOVER AIR FORCE BASE, Del., March 12 vehicle to the Air Force Mortuary Affairs Operations Center at Dover Air Force Base, Del. Story Center

Sensors Technology and Advanced Signal Processing Concepts for Layered Warfare/Layered Sensing

DTIC Science & Technology

2010-04-01

for challenged environments will require contributions from many diverse technical disciplines across AFRL, the Air Force and beyond. By providing a...APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED. STINFO COPY AIR FORCE...UNITED STATES AIR FORCE AIR FORCE MATERIEL COMMAND NOTICE AND SIGNATURE PAGE Using Government drawings, specifications, or other data

75 FR 22560 - Federal Advisory Committee; U.S. Air Force Scientific Advisory Board; Charter Renewal

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-29

... Chairperson. In addition, the Secretary of the Air Force may appoint, as deemed necessary non-voting... provided to the membership for their consideration. Contact information for the U.S. Air Force Scientific... DEPARTMENT OF DEFENSE Office of the Secretary Federal Advisory Committee; U.S. Air Force...

Geologic investigation :an update of subsurface geology on Kirtland Air Force Base, New Mexico.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Hart, Dirk

The objective of this investigation was to generate a revised geologic model of Kirtland Air Force Base (KAFB) incorporating the geological and geophysical data produced since the Site-Wide Hydrogeologic Characterization Project (SWHC) of 1994 and 1995. Although this report has certain stand-alone characteristics, it is intended to complement the previous work and to serve as a status report as of late 2002. In the eastern portion of KAFB (Lurance Canyon and the Hubbell bench), of primary interest is the elevation to which bedrock is buried under a thin cap of alluvium. Elevation maps of the bedrock top reveal the paleodrainagemore » that allows for the interpretation of the area's erosional history. The western portion of KAFB consists of the eastern part of the Albuquerque basin where bedrock is deeply buried under Santa Fe Group alluvium. In this area, the configuration of the down-to-the-west, basin-bounding Sandia and West Sandia faults is of primary interest. New geological and geophysical data and the reinterpretation of old data help to redefine the location and magnitude of these elements. Additional interests in this area are the internal stratigraphy and structure of the Santa Fe Group. Recent data collected from new monitoring wells in the area have led to a geologic characterization of the perched Tijeras Arroyo Groundwater system and have refined the known limits of the Ancestral Rio Grande fluvial sediments within the Santa Fe Group. Both the reinterpretation of the existing data and a review of the regional geology have shown that a segment of the boundary between the eastern and western portions of KAFB is a complicated early Tertiary (Laramide) wrench-fault system, the Tijeras/Explosive Ordnance Disposal Area/Hubbell Spring system. A portion of this fault zone is occupied by a coeval ''pull-apart'' basin filled with early Tertiary conglomerates, whose exposures form the ''Travertine Hills''.« less

Measurement of unsteady pressures in rotating systems

NASA Technical Reports Server (NTRS)

Kienappel, K.

1978-01-01

The principles of the experimental determination of unsteady periodic pressure distributions in rotating systems are reported. An indirect method is discussed, and the effects of the centrifugal force and the transmission behavior of the pressure measurement circuit were outlined. The required correction procedures are described and experimentally implemented in a test bench. Results show that the indirect method is suited to the measurement of unsteady nonharmonic pressure distributions in rotating systems.

A simple method for assessment of muscle force, velocity, and power producing capacities from functional movement tasks.

PubMed

Zivkovic, Milena Z; Djuric, Sasa; Cuk, Ivan; Suzovic, Dejan; Jaric, Slobodan

2017-07-01

A range of force (F) and velocity (V) data obtained from functional movement tasks (e.g., running, jumping, throwing, lifting, cycling) performed under variety of external loads have typically revealed strong and approximately linear F-V relationships. The regression model parameters reveal the maximum F (F-intercept), V (V-intercept), and power (P) producing capacities of the tested muscles. The aim of the present study was to evaluate the level of agreement between the routinely used "multiple-load model" and a simple "two-load model" based on direct assessment of the F-V relationship from only 2 external loads applied. Twelve participants were tested on the maximum performance vertical jumps, cycling, bench press throws, and bench pull performed against a variety of different loads. All 4 tested tasks revealed both exceptionally strong relationships between the parameters of the 2 models (median R = 0.98) and a lack of meaningful differences between their magnitudes (fixed bias below 3.4%). Therefore, addition of another load to the standard tests of various functional tasks typically conducted under a single set of mechanical conditions could allow for the assessment of the muscle mechanical properties such as the muscle F, V, and P producing capacities.

Airpower Liaison for the Land Component: The Primacy of the USAF TACP Construct

DTIC Science & Technology

2014-06-13

Force Doctrine Document AFSC Air Force Specialty Code AFUTL Air Force Universal Task List AI Air Interdiction ALO Air Liaison Officer AMLO Air...ALOs), Air Mobility Liaison Officers ( AMLOs ), Air Support Operations Centers (ASOCs), Battalion Air Liaison Officers (BALOs), Intelligence...Support from AMLOs can provide the requisite expertise within the TACP to facilitate airpower’s integration into movement requirements to and from and

Fuel-Flexible Gasification-Combustion Technology for Production of H2 and Sequestration-Ready CO2

DOE Office of Scientific and Technical Information (OSTI.GOV)

George Rizeq; Janice West; Raul Subia

GE Global Research is developing an innovative energy technology for coal gasification with high efficiency and near-zero pollution. This Unmixed Fuel Processor (UFP) technology simultaneously converts coal, steam and air into three separate streams of hydrogen-rich gas, sequestration-ready CO{sub 2}, and high-temperature, high-pressure vitiated air to produce electricity in gas turbines. This is the draft final report for the first stage of the DOE-funded Vision 21 program. The UFP technology development program encompassed lab-, bench- and pilot-scale studies to demonstrate the UFP concept. Modeling and economic assessments were also key parts of this program. The chemical and mechanical feasibility weremore » established via lab and bench-scale testing, and a pilot plant was designed, constructed and operated, demonstrating the major UFP features. Experimental and preliminary modeling results showed that 80% H{sub 2} purity could be achieved, and that a UFP-based energy plant is projected to meet DOE efficiency targets. Future work will include additional pilot plant testing to optimize performance and reduce environmental, operability and combined cycle integration risks. Results obtained to date have confirmed that this technology has the potential to economically meet future efficiency and environmental performance goals.« less

Rate and reaction probability of the surface reaction between ozone and dihydromyrcenol measured in a bench scale reactor and a room-sized chamber

NASA Astrophysics Data System (ADS)

Shu, Shi; Morrison, Glenn C.

2012-02-01

Low volatility terpenoids emitted from consumer products can react with ozone on surfaces and may significantly alter concentrations of ozone, terpenoids and reaction products in indoor air. We measured the reaction probability and a second-order surface-specific reaction rate for the ozonation of dihydromyrcenol, a representative indoor terpenoid, adsorbed onto polyvinylchloride (PVC), glass, and latex paint coated spheres. The reaction probability ranged from (0.06-8.97) × 10 -5 and was very sensitive to humidity, substrate and mass adsorbed. The average surface reaction probability is about 10 times greater than that for the gas-phase reaction. The second-order surface-specific rate coefficient ranged from (0.32-7.05) × 10 -15 cm 4 s -1 molecule -1and was much less sensitive to humidity, substrate, or mass adsorbed. We also measured the ozone deposition velocity due to adsorbed dihydromyrcenol on painted drywall in a room-sized chamber, Based on that, we calculated the rate coefficient ((0.42-1.6) × 10 -15 cm 4 molecule -1 s -1), which was consistent with that derived from bench-scale experiments for the latex paint under similar conditions. We predict that more than 95% of dihydromyrcenol oxidation takes place on indoor surfaces, rather than in building air.

Transforming The Munitions And Missile Maintenance Officer Career Field

DTIC Science & Technology

2016-04-01

is a United States Air Force Officer currently attending Air and Space Command College at Maxwell Air Force Base , AL. Maj Edington was previously...INTRODUCTION Since the unauthorized transportation of nuclear warheads from Minot Air Force Base (MAFB) to Barksdale Air Force Base (BAFB) and the mistaken... base .66 These factors coupled with risk-aversion for anything but perfect results during inspections (i.e. zero defects), and the well-established

An Optimization of the Maintenance Assets Distribution Network in the Argentine Air Force

DTIC Science & Technology

2015-03-26

Air Force (2010). Manual de Conduccion Logistica . Buenos Aires: HQ Argentine Air Force. Argentine Air Force (2012). El vuelo del condor: 1912-2012...recommendation was made to consider organic or private transportation and reduce transportation time in order to improve responsiveness and drive down...determine overall transportation demand and capacity required for a defined level of service, and to evaluate the tradeoffs between costs and service

Characterization of a Hyperspectral Chromotomographic Imaging Ground System

DTIC Science & Technology

2012-03-22

developed by the Air Force Institute of Technology (AFIT). The optical model is constructed using Zemax and MATLAB. The model provides the mechanism required...can also be used to incorporate interferometric measurements of optical components and model them in Zemax. The model uses a Zernike Phase Surface to...THE AIR FORCE AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY Wright-Patterson Air Force Base, Ohio DISTRIBUTION STATEMENT A APPROVED FOR PUBLIC

Environmental Assessment: Military Family Housing Privatization Maxwell Air Force Base

DTIC Science & Technology

2005-06-01

Ray L. Raton Mildred J . Worthy February 9, 2005 Lt. Colonel David W. Maninez Deputy Commander, 42nd MSG 50 South LeMay Plaza (Bldg 804) Maxwell ...Environmental Assessment Military Family Housing Privatization Maxwell Air Force Base United States Air Force Air Education and Training Command... Maxwell Air Force Base, Alabama June 2005 Report Documentation Page Form ApprovedOMB No. 0704-0188 Public reporting burden for the collection of

International Affairs Programs: The Air Force Versus the Army

DTIC Science & Technology

2015-10-01

individual tutoring programs . Additionally RAS personnel are offered regional enhancement studies opportunities at several facilities.48 RAS personnel...AU/ACSC/2015 AIR COMMAND AND STAFF COLLEGE AIR UNIVERSITY INTERNATIONAL AFFAIRS PROGRAMS : THE AIR FORCE VERSUS THE ARMY by Robin L...5 COMPARISON: INTERNATIONAL AFFAIRS PROGRAMS AIR FORCE VERSUS ARMY 8

32 CFR 728.25 - Army and Air Force National Guard personnel.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 32 National Defense 5 2013-07-01 2013-07-01 false Army and Air Force National Guard personnel. 728... Guard Personnel § 728.25 Army and Air Force National Guard personnel. (a) Medical and dental care. Upon... Care) and AFR 168-6 (Persons Authorized Medical Care) to members of the Army and Air Force National...

32 CFR 728.25 - Army and Air Force National Guard personnel.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 32 National Defense 5 2012-07-01 2012-07-01 false Army and Air Force National Guard personnel. 728... Guard Personnel § 728.25 Army and Air Force National Guard personnel. (a) Medical and dental care. Upon... Care) and AFR 168-6 (Persons Authorized Medical Care) to members of the Army and Air Force National...

32 CFR 728.25 - Army and Air Force National Guard personnel.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 5 2010-07-01 2010-07-01 false Army and Air Force National Guard personnel. 728... Guard Personnel § 728.25 Army and Air Force National Guard personnel. (a) Medical and dental care. Upon... Care) and AFR 168-6 (Persons Authorized Medical Care) to members of the Army and Air Force National...

32 CFR 728.25 - Army and Air Force National Guard personnel.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 32 National Defense 5 2011-07-01 2011-07-01 false Army and Air Force National Guard personnel. 728... Guard Personnel § 728.25 Army and Air Force National Guard personnel. (a) Medical and dental care. Upon... Care) and AFR 168-6 (Persons Authorized Medical Care) to members of the Army and Air Force National...

78 FR 59343 - Meeting of the National Commission on the Structure of the Air Force

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-26

... of the Air Force AGENCY: Director of Administration and Management, DoD. ACTION: Notice of Advisory... following Federal Advisory Committee meeting of the National Commission on the Structure of the Air Force... Commission on the Structure of the Air Force, 1950 Defense Pentagon, Room 3A874, Washington, DC 20301-1950...

32 CFR 644.368 - Procedures and responsibilities for care, custody, accountability, and maintenance.

Code of Federal Regulations, 2010 CFR

2010-07-01

... their jurisdiction until final disposition is effected. (c) Department of the Air Force property. Pursuant to AFR 87-4, the Department of the Air Force is responsible for care and custody of excess Air Force real property. However, upon request by the Air Force DEs may assume custody if no costs are...

32 CFR 644.368 - Procedures and responsibilities for care, custody, accountability, and maintenance.

Code of Federal Regulations, 2013 CFR

2013-07-01

... property under their jurisdiction until final disposition is effected. (c) Department of the Air Force property. Pursuant to AFR 87-4, the Department of the Air Force is responsible for care and custody of excess Air Force real property. However, upon request by the Air Force DEs may assume custody if no costs...

32 CFR 644.368 - Procedures and responsibilities for care, custody, accountability, and maintenance.

Code of Federal Regulations, 2011 CFR

2011-07-01

... property under their jurisdiction until final disposition is effected. (c) Department of the Air Force property. Pursuant to AFR 87-4, the Department of the Air Force is responsible for care and custody of excess Air Force real property. However, upon request by the Air Force DEs may assume custody if no costs...

The Air Force Research Laboratory’s In-Space Propulsion Program

DTIC Science & Technology

2015-02-01

Air Force Research Laboratory (AFMC) AFRL /RQRS 1 Ara...MONITOR’S ACRONYM(S) Air Force Research Laboratory (AFMC) AFRL /RQR 5 Pollux Drive 11. SPONSOR/MONITOR’S REPORT Edwards AFB CA 93524-7048 NUMBER(S) AFRL ...illustrate the rationale behind AFRL’s technology development strategy. INTRODUCTION The Air Force Research Laboratory ( AFRL ) is the technology

Perspectives from Former Executives of the DOD Corporate Research Laboratories

DTIC Science & Technology

2009-03-01

Research Laboratory (NRL) in Washington, DC; and the Air Force Research Laboratory ( AFRL ) in Dayton, Ohio respectively. These individuals are: John Lyons...13 Vincent Russo and the Air Force Research Laboratory The Air Force Research Laboratory ( AFRL ) was activated in 1997. Prior to the creation of... AFRL , the Air Force conducted its research at four major

Air Force Research Laboratory Sensors Directorate Leadership Legacy, 1960-2011

DTIC Science & Technology

2011-03-01

AFRL -RY-WP-TM-2011-1017 AIR FORCE RESEARCH LABORATORY SENSORS DIRECTORATE LEADERSHIP LEGACY, 1960-2011 Compiled by Raymond C. Rang...Structures Divi- sion, Space Vehicles Directorate, Air Force Research Laboratory , Kirtland AFB, N.M. 7. March 1998 - July 1999, Chief, Integration and... Research Laboratory ( AFRL ), and Deputy Director of the Sensors Direc- torate, Air Force Research

Phillips Lab Project Manager’s Handbook

DTIC Science & Technology

1994-04-15

Phillips Lab continues to be the Air Force Phillips Laboratory (PL) center of excellence for space research and Kirtland AFB, New...POINTS OF CONTACT pages of world history. In 1949, the Cambridge Field Station was renamed the Kirtland AFB: Air Force Cambridge Research Laboratories ...by the Air Force’s facilities are geographically located. Phillips Laboratory at Kirtland Air Force

AFRL Solid Propellant Laboratory Explosive Siting and Renovation Lessons Learned

DTIC Science & Technology

2010-05-19

AFRL Solid Propellant Laboratory Explosive Siting and Renovation Lessons Learned Daniel F. Schwartz Air Force Research Laboratory ...9. SPONSORING / MONITORING AGENCY NAME(S) AND ADDRESS(ES) 10. SPONSOR/MONITOR’S ACRONYM(S) Air Force Research Laboratory (AFMC) AFRL /RZS...provide the United States Air Force with advanced rocket propulsion technologies, the Air Force Research

Redox Liquid Phase Exfoliation of Layered Transition Metal Dichalcogenides (Postprint)

DTIC Science & Technology

2016-12-29

RESEARCH LABORATORY MATERIALS AND MANUFACTURING DIRECTORATE WRIGHT-PATTERSON AIR FORCE BASE, OH 45433-7750 AIR FORCE MATERIEL COMMAND UNITED...ADDRESS(ES) 10. SPONSORING/MONITORING AGENCY ACRONYM(S) Air Force Research Laboratory Materials and Manufacturing Directorate Wright...Bultman, Adam Waite, Ming-Siao Hsiao, Richard A. Vaia* Materials and Manufacturing Directorate, Air Force Research Laboratory, Wright-Patterson AFB, Ohio

32 CFR 644.475 - Excessing Army military and Air Force property.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 4 2010-07-01 2010-07-01 true Excessing Army military and Air Force property... the Related Land) § 644.475 Excessing Army military and Air Force property. The procedures for placing... commander concerned is required. When, under AFR 87-4, the responsible DE is called upon by the Air Force...

10. "TEST STAND 15, AIR FORCE FLIGHT TEST CENTER." ca. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. "TEST STAND 1-5, AIR FORCE FLIGHT TEST CENTER." ca. 1958. Test Area 1-115. Original is a color print, showing Test Stand 1-5 from below, also showing the superstructure of TS1-4 at left. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Leuhman Ridge near Highways 58 & 395, Boron, Kern County, CA

75 FR 53075 - Science and Technology Reinvention Laboratory Personnel Management Demonstration Project...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-30

... Demonstration Project, Department of the Air Force, Air Force Research Laboratory (AFRL); Notice #0;#0;Federal... Project, Department of the Air Force, Air Force Research Laboratory (AFRL) AGENCY: Office of the Deputy... amendment changed the amount of time required to be assessed under CCS from 180 to 90 calendar days and was...

Acquisition Research Topics Catalog.

DTIC Science & Technology

1981-01-01

AD-AG98 929 AIR FORCE BUSINESS RESEARCH MANAGEMENT CENTER WRIGHT--ETC F/S 5/1 1981ACQUISITION RESEARCH TOPICS CATALOG.(U) I UNCLASSIFIED NL I EEL...kELECTE MAY 14 1981 uoAIR FORCE BUSINESS RESEARCH MANAGEMENT CENTERI Wright-Patterson Air Force Base, Ohio 45433- ’ ’jCH MA G’ A rs l "-DIT.’u7 I ST AMEN’T...A /, App --vA fc, piibli release; I. . . ’li iLl :i ’.n: ix~lited *1,.: THE AIR FORCE BUSINESS RESEARCH MANAGEMENT CENTER WRIGHT-PATTERSON AIR FORCE

Development of ITM oxygen technology for integration in IGCC and other advanced power generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Armstrong, Phillip A.

2015-03-31

Ion Transport Membrane (ITM) technology is based on the oxygen-ion-conducting properties of certain mixed-metal oxide ceramic materials that can separate oxygen from an oxygen-containing gas, such as air, under a suitable driving force. The “ITM Oxygen” air separation system that results from the use of such ceramic membranes produces a hot, pure oxygen stream and a hot, pressurized, oxygen-depleted stream from which significant amounts of energy can be extracted. Accordingly, the technology integrates well with other high-temperature processes, including power generation. Air Products and Chemicals, Inc., the Recipient, in conjunction with a dozen subcontractors, developed ITM Oxygen technology under thismore » five-phase Cooperative Agreement from the laboratory bench scale to implementation in a pilot plant capable of producing power and 100 tons per day (TPD) of purified oxygen. A commercial-scale membrane module manufacturing facility (the “CerFab”), sized to support a conceptual 2000 TPD ITM Oxygen Development Facility (ODF), was also established and operated under this Agreement. In the course of this work, the team developed prototype ceramic production processes and a robust planar ceramic membrane architecture based on a novel ceramic compound capable of high oxygen fluxes. The concept and feasibility of the technology was thoroughly established through laboratory pilot-scale operations testing commercial-scale membrane modules run under industrial operating conditions with compelling lifetime and reliability performance that supported further scale-up. Auxiliary systems, including contaminant mitigation, process controls, heat exchange, turbo-machinery, combustion, and membrane pressure vessels were extensively investigated and developed. The Recipient and subcontractors developed efficient process cycles that co-produce oxygen and power based on compact, low-cost ITMs. Process economics assessments show significant benefits relative to state-of-the-art cryogenic air separation technology in energy-intensive applications such as IGCC with and without carbon capture.« less

Aeroservoelastic and Structural Dynamics Research on Smart Structures Conducted at NASA Langley Research Center

NASA Technical Reports Server (NTRS)

McGowan, Anna-Maria Rivas; Wilkie, W. Keats; Moses, Robert W.; Lake, Renee C.; Florance, Jennifer Pinkerton; Wieseman, Carol D.; Reaves, Mercedes C.; Taleghani, Barmac K.; Mirick, Paul H.; Wilbur, Matthew L.

1998-01-01

An overview of smart structures research currently underway at the NASA Langley Research Center in the areas of aeroservoelasticity and structural dynamics is presented. Analytical and experimental results, plans, potential technology pay-offs, and challenges are discussed. The goal of this research is to develop the enabling technologies to actively and passively control aircraft and rotorcraft vibration and loads using smart devices. These enabling technologies and related research efforts include developing experimentally-validated finite element and aeroservoelastic modeling techniques; conducting bench experimental tests to assess feasibility and understand system trade-offs; and conducting large-scale wind- tunnel tests to demonstrate system performance. The key aeroservoelastic applications of this research include: active twist control of rotor blades using interdigitated electrode piezoelectric composites and active control of flutter, and gust and buffeting responses using discrete piezoelectric patches. In addition, NASA Langley is an active participant in the DARPA/ Air Force Research Laboratory/ NASA/ Northrop Grumman Smart Wing program which is assessing aerodynamic performance benefits using smart materials. Keywords: aeroelasticity, smart structures, piezoelectric actuators, active fiber composites, rotorcraft, buffet load alleviation, individual blade control, aeroservoelasticity, shape memory alloys, damping augmentation, piezoelectric power consumption

Environmental Assessment for Implementation of the Schriever Air Force Base Integrated Natural Resources Management Plan

DTIC Science & Technology

2008-03-01

Force Policy Directive (AFPD) 32-70, Environmental Quality ( July 20, 1994); and Air Force Instruction (AFI) 32-7064, Integrated Natural Resources...Environmental Conservation Program; Air Force Policy Directive (AFPD) 32-70, Environmental Quality ( July 20, 1994); and Air Force Instruction (AFI...thunderstorms occur in the late spring to summer months along the Front Range and can result in flash flood conditions (greatest potential in July and August

Gold Standard Testing of Motion Based Tracking Systems

DTIC Science & Technology

2017-03-15

NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER H0L0 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) 8. PERFORMING ORGANIZATION REPORT NUMBER 9...LABORATORY 711TH HUMAN PERFORMANCE WING, AIRMAN SYSTEMS DIRECTORATE, WRIGHT-PATTERSON AIR FORCE BASE, OH 45433 AIR FORCE MATERIEL COMMAND UNITED STATES AIR...711th Human Performance Wing 711th Human Performance Wing Air Force Research Laboratory Air Force Research Laboratory This report is published in the

An Analysis of Air Force Management of Turbine Engine Monitoring Systems (TEMS).

DTIC Science & Technology

1980-06-01

AIR FORCE AIR UNIVERSITY (ATC) C AIR FORCE INSTITUTE OF TECHNOLOGY LWright-Patterson Air Force Base, Ohio 80 9 22 057 All BBO RCE j GEMEM Elbert B...detrimental ideas, or deleterious information are contained therein. Furthermore, the views expressed in the document are those of the author(s) and...role problems, information flow and integration problems, and leadership and command problems. Four alternative management concepts were analyzed. Based

Chemical Vapor Deposition of Multispectral Domes

DTIC Science & Technology

1975-04-01

optical testing, was also cut out as indicated in Figure 10. The image spoiling measureinents were performed at the Air Force Avionics Laboratory on...AD-A014 362 CHEMICAL VAPOR DEPOSITION OF MULTISPECTRAL DOMES B. A. diBenedetto, et al Raytheon Company Prepared for: Air Force Materials Laboratory...Approved for public release; distribution unlimited. ) F) .• •~~EP 7 ’+ i.i AIR FORCE MATERIALS LABORATORY AIR FORCE SYSTEMS COMMAND WRIGHT-PATrERSON AIR

Advanced diesel electronic fuel injection and turbocharging

NASA Astrophysics Data System (ADS)

Beck, N. J.; Barkhimer, R. L.; Steinmeyer, D. C.; Kelly, J. E.

1993-12-01

The program investigated advanced diesel air charging and fuel injection systems to improve specific power, fuel economy, noise, exhaust emissions, and cold startability. The techniques explored included variable fuel injection rate shaping, variable injection timing, full-authority electronic engine control, turbo-compound cooling, regenerative air circulation as a cold start aid, and variable geometry turbocharging. A Servojet electronic fuel injection system was designed and manufactured for the Cummins VTA-903 engine. A special Servojet twin turbocharger exhaust system was also installed. A series of high speed combustion flame photos was taken using the single cylinder optical engine at Michigan Technological University. Various fuel injection rate shapes and nozzle configurations were evaluated. Single-cylinder bench tests were performed to evaluate regenerative inlet air heating techniques as an aid to cold starting. An exhaust-driven axial cooling air fan was manufactured and tested on the VTA-903 engine.

Differences in unilateral chest press muscle activation and kinematics on a stable versus unstable surface while holding one versus two dumbbells

PubMed Central

Patterson, Jeffrey M.; Oppenheimer, Nicole E.; Feser, Erin H.

2015-01-01

Training the bench press exercise on a traditional flat bench does not induce a level of instability as seen in sport movements and activities of daily living. Twenty participants were recruited to test two forms of instability: using one dumbbell rather than two and lifting on the COR bench compared to a flat bench. Electromyography (EMG) amplitudes of the pectoralis major, middle trapezius, external oblique, and internal oblique were recorded and compared. Differences in range of motion (ROM) were evaluated by measuring an angular representation of the shoulder complex. Four separate conditions of unilateral bench press were tested while lifting on a: flat bench with one dumbbell, flat bench with two dumbbells, COR Bench with one dumbbell, and COR Bench with two dumbbells. The results imply that there are no differences in EMG amplitude or ROM between the COR bench and traditional bench. However, greater ROM was found to be utilized in the single dumbbell condition, both in the COR bench and the flat bench. PMID:26528421

Improving Development Teams to Support Deliberate Development of Air Force Officers

DTIC Science & Technology

2015-01-01

the USAF Cyber Force (Scott et al., 2010) • Understrength Air Force Officer Career Fields: A Force Management Approach ( Galway et al., 2005...D., “The New Way of Officer Assignments,” Air Force Magazine, June 1998, pp. 64–67. Galway , Lionel A., Richard J. Buddin, Michael R. Thirtle, Peter

Environmental Assessment Housing Transfer at Grand Forks AFB, North Dakota

DTIC Science & Technology

2005-01-27

AIR FORCE BASE ...Equipment…………. 28 9 ACRONYMS, ABBREVIATIONS, AND TERMS AAM Annual Arithmetic Mean ACM Asbestos-Containing Material AFB Air Force Base AFI Air ...of No Significant Impact ft Feet ft3/s feet cubed per meter 10 GFAFB Grand Forks Air Force Base HAP Hazardous Air Pollutants hr Hour

Historical Lessons of Air Force Communications

DTIC Science & Technology

2010-12-01

AU/ACSC/ CUSTINE /AY10 AIR COMMAND AND STAFF COLLEGE AIR UNIVERSITY HISTORICAL LESSONS OF AIR FORCE COMMUNICATIONS...by Jay D. Custine , Civ, DAF A Research Report Submitted to the Faculty In Partial Fulfillment of the Graduation...Requirements Advisor: Lt Col Paul E. Griffith Maxwell Air Force Base, Alabama December 2010 AU/ACSC/ CUSTINE /AY10 ii

77 FR 1913 - Notice of Meeting of the Agricultural Air Quality Task Force

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-12

... Conservation Service Notice of Meeting of the Agricultural Air Quality Task Force AGENCY: Natural Resources...), Agricultural Air Quality Task Force (AAQTF) will meet to continue discussions on critical air quality issues... relationship between agricultural production and air quality. The meeting is open to the public, and a draft...

33 CFR 334.560 - Banana River at Patrick Air Force Base, Fla.; restricted area.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Commander, 45th Space Wing, Patrick Air Force Base, Florida, and such agencies as he/she may designate. [29... 33 Navigation and Navigable Waters 3 2011-07-01 2011-07-01 false Banana River at Patrick Air Force... River at Patrick Air Force Base, Fla.; restricted area. (a) The area. The waters within an area...

33 CFR 334.560 - Banana River at Patrick Air Force Base, Fla.; restricted area.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Commander, 45th Space Wing, Patrick Air Force Base, Florida, and such agencies as he/she may designate. [29... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Banana River at Patrick Air Force... River at Patrick Air Force Base, Fla.; restricted area. (a) The area. The waters within an area...

33 CFR 334.560 - Banana River at Patrick Air Force Base, Fla.; restricted area.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Commander, 45th Space Wing, Patrick Air Force Base, Florida, and such agencies as he/she may designate. [29... 33 Navigation and Navigable Waters 3 2012-07-01 2012-07-01 false Banana River at Patrick Air Force... River at Patrick Air Force Base, Fla.; restricted area. (a) The area. The waters within an area...

33 CFR 334.560 - Banana River at Patrick Air Force Base, Fla.; restricted area.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Commander, 45th Space Wing, Patrick Air Force Base, Florida, and such agencies as he/she may designate. [29... 33 Navigation and Navigable Waters 3 2013-07-01 2013-07-01 false Banana River at Patrick Air Force... River at Patrick Air Force Base, Fla.; restricted area. (a) The area. The waters within an area...

USAF Summer Research Program - 1994 Graduate Student Research Program Final Reports, Volume 8, Phillips Laboratory

DTIC Science & Technology

1994-12-01

Research Group at the Phillips Laboratory at Kirtland Air Force Base...for Summer Graduate Student Research Program Phillips Laboratory Sponsored by: Air Force Office of Scientific Research Boiling Air Force Base, DC...2390 S. York Street Denver, CO 80208-0177 Final Report for: Summer Faculty Research Program Phillips Laboratory Sponsored by: Air Force

33 CFR 165.768 - Security Zone; MacDill Air Force Base, Tampa Bay, FL.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Security Zone; MacDill Air Force....768 Security Zone; MacDill Air Force Base, Tampa Bay, FL. (a) Location. The following area is a... title. All waters within Tampa Bay, Florida in the vicinity of MacDill Air Force Base, including...

Discharge Processes in the Oxygen Plasma

DTIC Science & Technology

1981-04-01

for Period October 1975 - October 1980 Approved for public release; distribution unlimited C.) A "AERO PROPULSION LABORATORY L. AIR FORCE WRIGHT...AERONAUTICAL LABORATORIES AIR FORCE SYSTEMS COMMAND WRIGHT PATTERSON AIR FORCE BASE, OHIO 45433 816,., 009 Best Available Copy S...it different from Report) IS. SUPPLEMENTARY NOTES A Dissertation Presented to the Faculty of the School of Engineering of the Air Force Institute of

Encoding Gaussian Curvature in Glassy and Elastomeric Liquid Crystal Solids (Postprint)

DTIC Science & Technology

2016-05-04

unlimited. © 2016 THE ROYAL SOCIETY PUBLISHING (STINFO COPY) AIR FORCE RESEARCH LABORATORY MATERIALS AND MANUFACTURING DIRECTORATE WRIGHT...ACRONYM(S) Air Force Research Laboratory Materials and Manufacturing Directorate Wright-Patterson Air Force Base, OH 45433-7750 Air Force Materiel...integration of such materials is a precondition for their exploitation in new devices. 15. SUBJECT TERMS nematic, elastomers, solids, curvature

Environmental Enrichment Protects against Functional Deficits caused by Traumatic Brain Injury

DTIC Science & Technology

2012-11-01

Herman University of Cincinnati November 2012 Interim Report AIR FORCE RESEARCH LABORATORY 711 HUMAN PERFORMANCE WING, HUMAN EFFECTIVENESS DIRECTORATE...Chief, Warfighter Interface Division Human Effectiveness Directorate 711 Human Performance Wing Air Force Research Laboratory This report is published...MONITOR’S ACRONYM(S) Air Force Materiel Command Air Force Research Laboratory 711th Human Performance Wing Human Effectiveness Directorate Warfighter

Air Force Special Operations Command > Home > POTFF

Science.gov Websites

Air Force Special Operations Command Air Force Special Operations Command Join the Air Force Home Sheets AFSOC Senior Leaders AFSOC Heritage Units 1st Special Operations Wing 24th Special Operations Wing 27th Special Operations Wing 352nd Special Operations Wing 353rd Special Operations Group 492nd Special

Air Force Integrated Personnel and Pay System (AFIPPS)

DTIC Science & Technology

2016-03-01

2016 Major Automated Information System Annual Report Air Force Integrated Personnel and Pay System (AFIPPS) Defense Acquisition Management...DSN Fax: 665-1207 Date Assigned: February 1, 2016 Program Information Program Name Air Force Integrated Personnel and Pay System (AFIPPS) DoD...therefore, no Original Estimate has been established. AFIPPS 2016 MAR UNCLASSIFIED 4 Program Description Air Force Integrated Personnel and Pay

Command Clairvoyance: Strategically Transforming AFRC Through Total Force and Leadership

DTIC Science & Technology

2012-01-19

backstop for 21st century operations. Lieutenant General Charles Stenner , Chief of the Air Force Reserve, encapsulated this by stating, "The Air Force...and it is a venue that requires the Air Force and AFRC to change in unison, as General Stenner acknowledged: The Air Force is under the same...another generation of TFI savvy leaders. Aligned with General Stenner ‟s previous comments, AFRC needs to foster an “adaptive culture” in order to

Deflagration to Shock to Detonation Transition of Energetic Propellants.

DTIC Science & Technology

1984-07-01

Champaign Urbana, IL 61801 Prepared for: Air Force Office of Scientific Research Aerospace Sciences Directorate: Bldg. 410 Boiling Air Force Base, DC 20332...Program Manager: Dr. Henry R. Radoski For Research Performed under ()Grant AFOSR 81-0145 During Period I June 1983 through 30 May 1984 AIR ,,1 C~i...ADDRESS 12. REPORT DATE / Air Force Office of Scientific Research/Q July 1984 Building 410; ATTN: Henry R. Radoski 13. NUMBER OF AGES Bolling Air Force

IS FREE REALLY FREE PALACE ACQUIRE AS AN EFFECTIVE FORCE RENEWAL SOURCE FOR AIR FORCE PUBLIC AFFAIRS

DTIC Science & Technology

2016-02-29

AU/ACSC/2016 AIR COMMAND AND STAFF COLLEGE AIR UNIVERSITY IS FREE REALLY FREE ? PALACE ACQUIRE AS AN EFFECTIVE FORCE RENEWAL SOURCE FOR AIR...transfer-eligible candidates, and external applicants. Ultimately, this research reveals, the cost – in both money and manpower – does not support...these employees provide to their sponsoring offices in “ free manning.” 5 CHAPTER 1 Introduction Public Affairs is key aspect of Air Force

Effect of jet injection on infectivity of measles, mumps, and rubella vaccine in a bench model.

PubMed

Coughlin, Melissa M; Collins, Marcus; Saxon, Gene; Jarrahian, Courtney; Zehrung, Darin; Cappello, Chris; Dhere, Rajeev; Royals, Michael; Papania, Mark; Rota, Paul A

2015-08-26

Disposable-syringe jet injectors (DSJIs) with single-use, auto disable, needle-free syringes offer the opportunity to avoid hazards associated with injection using a needle and syringe. Clinical studies have evaluated DSJIs for vaccine delivery, but most studies have focused on inactivated, subunit, or DNA vaccines. Questions have been raised about possible damage to live attenuated viral vaccines by forces generated during the jet injection process. This study examines the effect of jet injection on the integrity of measles, mumps, and rubella vaccine (MMR), measured by viral RNA content and infectivity. Three models of DSJIs were evaluated, each generating a different ejection force. Following jet injection, the RNA content for each of the vaccine components was measured using RT-qPCR immediately after injection and following passage in Vero cells. Jet injection was performed with and without pig skin as a simulation of human skin. There was little to no reduction of RNA content immediately following jet injection with any of the three DSJIs. Samples passaged in Vero cells showed no loss in infectivity of the measles vaccine following jet injection. Mumps vaccine consistently showed increased replication following jet injection. Rubella vaccine showed no loss after jet injection alone but some infectivity loss following injection through pig skin with two of the devices. Overall, these data demonstrated that forces exerted on a live attenuated MMR vaccine did not compromise vaccine infectivity. The bench model and protocol used in this study can be applied to evaluate the impact of jet injection on other live virus vaccines. Published by Elsevier Ltd.

Evaluation of force-velocity and power-velocity relationship of arm muscles.

PubMed

Sreckovic, Sreten; Cuk, Ivan; Djuric, Sasa; Nedeljkovic, Aleksandar; Mirkov, Dragan; Jaric, Slobodan

2015-08-01

A number of recent studies have revealed an approximately linear force-velocity (F-V) and, consequently, a parabolic power-velocity (P-V) relationship of multi-joint tasks. However, the measurement characteristics of their parameters have been neglected, particularly those regarding arm muscles, which could be a problem for using the linear F-V model in both research and routine testing. Therefore, the aims of the present study were to evaluate the strength, shape, reliability, and concurrent validity of the F-V relationship of arm muscles. Twelve healthy participants performed maximum bench press throws against loads ranging from 20 to 70 % of their maximum strength, and linear regression model was applied on the obtained range of F and V data. One-repetition maximum bench press and medicine ball throw tests were also conducted. The observed individual F-V relationships were exceptionally strong (r = 0.96-0.99; all P < 0.05) and fairly linear, although it remains unresolved whether a polynomial fit could provide even stronger relationships. The reliability of parameters obtained from the linear F-V regressions proved to be mainly high (ICC > 0.80), while their concurrent validity regarding directly measured F, P, and V ranged from high (for maximum F) to medium-to-low (for maximum P and V). The findings add to the evidence that the linear F-V and, consequently, parabolic P-V models could be used to study the mechanical properties of muscular systems, as well as to design a relatively simple, reliable, and ecologically valid routine test of the muscle ability of force, power, and velocity production.

Forced-air warming design: evaluation of intake filtration, internal microbial buildup, and airborne-contamination emissions.

PubMed

Reed, Mike; Kimberger, Oliver; McGovern, Paul D; Albrecht, Mark C

2013-08-01

Forced-air warming devices are effective for the prevention of surgical hypothermia. However, these devices intake nonsterile floor-level air, and it is unknown whether they have adequate filtration measures to prevent the internal buildup or emission of microbial contaminants. We rated the intake filtration efficiency of a popular current-generation forced-air warming device (Bair Hugger model 750, Arizant Healthcare) using a monodisperse sodium chloride aerosol in the laboratory. We further sampled 23 forced-air warming devices (same model) in daily hospital use for internal microbial buildup and airborne-contamination emissions via swabbing and particle counting. Laboratory testing found the intake filter to be 63.8% efficient. Swabbing detected microorganisms within 100% of the forced-air warming blowers sampled, with isolates of coagulase-negative staphylococci, mold, and micrococci identified. Particle counting showed 96% of forced-air warming blowers to be emitting significant levels of internally generated airborne contaminants out of the hose end. These findings highlight the need for upgraded intake filtration, preferably high-efficiency particulate air filtration (99.97% efficient), on current-generation forced-air warming devices to reduce contamination buildup and emission risks.

Preparing for the Unthinkable: DOD Support to Foreign Consequence Management

DTIC Science & Technology

2010-05-03

Nuclear Disaster ” (research paper, Maxwell Air Force Base, AL: Air University, 2001), 23. 17 Department of Defense Consequence Management...States Government Response to an Overseas Chemical, Biological, Radiological, or Nuclear Disaster ” (research paper, Maxwell Air Force Base, AL: Air...Government Response to an Overseas Chemical, Biological, Radiological, or Nuclear Disaster .” Research paper, Maxwell Air Force Base, AL: Air University

The United States Air Force Academy: A Bibliography 1954 - 1964

DTIC Science & Technology

1966-01-01

August 1958. 498 Stringer, Roger. " Pro Nobis Astra" (Class of 󈨁 selects its ring), Talon 5;5, May 1960. 499 Trotogott, Pete. Cadet...relate to establishing an air academy. These are not included since they have no specific bearing on the Academy as it now exists. The Library staff...Newsletter AF Times - Air Force Times Air Cond Heat & Ven - Air Conditioning, Heating, and Venti- lating Air Force Airman Air Power Historian

Compilation of FY 1997 Air Force General Funds Consolidated Financial Statements at the Defense Finance and Accounting Service Denver Center.

DTIC Science & Technology

1998-10-05

Consolidated Financial Statements to the Air Force Audit Agency. The Defense Finance and Accounting Service Denver Center maintained accounting records and prepared the FY 1997 financial statements for the Air Force. More than $343 billion in total assets was reported at year’s end in these statements, and total revenues for the year exceeded $64 billion. The Air Force Audit Agency disclaimed an opinion on these statements. Additionally, although the Office of Management and Budget does not require budgetary resource reporting until FY 1998, the Air Force

The Air Force Nurse Intern Program.

PubMed

Smith, R H

1991-08-01

The Air Force Nurse Intern Program is a 5-month-long introduction to Air Force nursing for BSN-prepared graduate nurses. The program is designed to facilitate the transition from civilian nursing student to practicing Air Force Nurse Corps Officer. After attending Military Indoctrination for Medical Service Officers, newly commissioned nurses attend the program at one of 10 Air Force medical centers before going to their permanent duty stations. Preceptors guide and instruct the interns at each of four clinical rotation sites. The author, a former nurse intern, describes some of the many opportunities available to nurse interns.

U.S. Air Force > SAPR

Science.gov Websites

for treatment in the military health system, and Air Force civilian (appropriated and non-appropriated (or equivalent) or installation vice wing commander, executing the Air Force's Sexual Assault

78 FR 53134 - Proposed Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-28

... and Uses: Require the collection of specific information on prospective Air Force contract flight... DEPARTMENT OF DEFENSE Department of the Air Force [Docket ID: USAF-2013-0034] Proposed Collection; Comment Request AGENCY: Air Education and Training Command (AETC/A5TS), Department of the Air Force...

Summer Research Program (1992). Graduate Student Research Program (GSRP) Reports. Volume 8. Phillips Laboratory.

DTIC Science & Technology

1992-12-28

Research Program Starfire Optical Range, Phillips Laboratory /LITE Kirtland Air Force Base, Albuquerque, NM 87117 Sponsored by: Air ... Phillips Laboratory Sponsored by: Air Force Office of Scientific Research Kirtland Air Force Base, Albuquerque, New Mexico September, 1992 18-1 PROGRESS...Report for: Summer Research Program Phillips Laboratory Sponsored by: Air

Opportunities for Nondestructive Evaluation: Quantitative Characterization (Postprint)

DTIC Science & Technology

2017-07-01

between the design and the as- manufactured and, ultimately, the as-maintained state. As this occurs with the article of interest being placed in...TESTING (STINFO COPY) AIR FORCE RESEARCH LABORATORY MATERIALS AND MANUFACTURING DIRECTORATE WRIGHT-PATTERSON AIR FORCE BASE, OH 45433-7750 AIR FORCE...MONITORING AGENCY NAME(S) AND ADDRESS(ES) 10. SPONSORING/MONITORING AGENCY ACRONYM(S) Air Force Research Laboratory Materials and Manufacturing

Challenges of Enterprise Wide AM for Air Force Sustainment

DTIC Science & Technology

2016-12-01

December 2016 Naguy is chief of the Air Force Life Cycle Management Center’s Product Support Engineering Division at Wright Patterson Air Force Base in...today and into the future. To truly capitalize on the full potential of AM, the Air Force Life Cycle Management Center (AFLCMC) in close collabora...approach for material standards and quality include un- derstanding powder characteristics, developing an enterprise material characterization

Automation of a Large Analytical Chemistry Laboratory

DTIC Science & Technology

1990-12-01

Division Brooks Air Force Base , Texas 78235-5501 NOTICES When Government drawings, specifications, or other data are used for any purpose other than a...been reviewed and is approved for publication. Air Force installations may direct requests for copies of this report to: Air Force Occupational and...remaining for the analyses. Our laboratory serves worldwide Air Force installations and therefore comes up against these sample holding time requirements

Profile of a Successful Civil Engineering Career in the United States Air Force.

DTIC Science & Technology

1984-09-01

Introduction ........ * * ........... 7 Career Success .. .. .. . .. . . ... 4- . .. ....... 8 Research Methods . .. . .. a.. . .. .. ............ it III...Definition of Terms I The following terms, for the purpose of this study, were defined as: Career success refers to an Air Force civil engineering officer...discussion of career success . An Air Force civil engineer is an officer currently possessing a 55XX duty Air Force . Specialty Code (AFSC). Statement of

78 FR 63169 - Meetings of the National Commission on the Structure of the Air Force; Cancellation of October 1...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-23

... of the Air Force; Cancellation of October 1, 2013, October 4, 2013 and October 9, 2013 Meetings... of the Air Force meetings scheduled for Tuesday, October 1, Friday, October 4, 2013 and Wednesday... Structure of the Air Force on October 1, 4, and 9 of 2013. As a result, the Department of Defense was unable...

75 FR 52724 - Procurement List Additions

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-27

...: 8405-00-FAB-0201--Man's, S/S, Air Force Shade 1550, Size 13\\1/ 2\\ NSN: 8405-00-FAB-0202--Man's, S/S, Air Force Shade 1550, Size 14 NSN: 8405-00-FAB-0203--Man's, S/S, Air Force Shade 1550, Size 14 \\1/ 2\\ NSN: 8405-00-FAB-0204--Man's, S/S, Air Force Shade 1550, Size 15 NSN: 8405-00-FAB-0212--Man's, S/S...

32 CFR 855.6 - Aircraft exempt from the requirement for a civil aircraft landing permit.

Code of Federal Regulations, 2012 CFR

2012-07-01

... individuals but leased by an Air Force aero club. (3) Aero clubs of other US military services. Note: This... aircraft owned by: (1) Any other US Government agency. (2) US Air Force aero clubs established as prescribed in AFI 34-117, Air Force Aero Club Program, and AFMAN 3-132, Air Force Aero Club Operations 1 . 1...

32 CFR 855.6 - Aircraft exempt from the requirement for a civil aircraft landing permit.

Code of Federal Regulations, 2013 CFR

2013-07-01

... individuals but leased by an Air Force aero club. (3) Aero clubs of other US military services. Note: This... aircraft owned by: (1) Any other US Government agency. (2) US Air Force aero clubs established as prescribed in AFI 34-117, Air Force Aero Club Program, and AFMAN 3-132, Air Force Aero Club Operations 1 . 1...

32 CFR 855.6 - Aircraft exempt from the requirement for a civil aircraft landing permit.

Code of Federal Regulations, 2014 CFR

2014-07-01

... individuals but leased by an Air Force aero club. (3) Aero clubs of other US military services. Note: This... aircraft owned by: (1) Any other US Government agency. (2) US Air Force aero clubs established as prescribed in AFI 34-117, Air Force Aero Club Program, and AFMAN 3-132, Air Force Aero Club Operations 1 . 1...

Systemization of Secure Computation

DTIC Science & Technology

2015-11-01

STINFO COPY AIR FORCE RESEARCH LABORATORY INFORMATION DIRECTORATE AFRL-RI-RS-TR-2015-241  UNITED STATES AIR FORCE  ROME, NY 13441 AIR FORCE...any patented invention that may relate to them. This report is the result of contracted fundamental research deemed exempt from public affairs...ES) Air Force Research Laboratory/RITA DARPA 525 Brooks Road 675 North Randolph Street Rome NY 13441-4505 Arlington, VA 22203

The ’In Lieu Of’ Myth. Airmen in Joint Ground Operations (Walker Paper, Number 13)

DTIC Science & Technology

2009-01-01

Romano, Dains , and Watts, “Air Force Breaks New Ground,” 14. 25. Air Force Print News, “Dangerous Road to Progress,” 42; and Air Force Print News...92 Romano, Lt Col Joseph L., III; Capt William M. Dains ; and Capt David T. Watts, “Air Force Breaks New Ground at Camp Bucca, Iraq.” Military

Sulfur dioxide reactions on ice surfaces: Implications for dry deposition to snow

Treesearch

Martha H. Conklin; Richard A. Sommerfeld; S. Kay Laird; John E. Villinski

1993-01-01

Controlled exposure of ice to a reactive gas, SO2, demonstrated the importance of the chemical composition of the ice surface on the accumulation of acidity in snow. In a series of bench-scale continuous-flow column experiments run at four temperatures (-1, -8, -30 and -60°C), SO2 was shown to dissolve and to react with other species in the ice-air interfacial region...

A Strategy To Increase United States Air Force Fighter Pilot Retention And Morale: Legendary Ace Robin Olds On The Silver Screen

DTIC Science & Technology

2016-02-16

Force should consider approaching the motion picture industry to produce a film about the life of Legendary Ace Robin Olds. This approach could capture...option must be investigated. Teaming with film producers is a valid way to promote the history of the Air Force, shaping a positive public image, and...morale. As a solution to increase Air Force warrior morale, the Air Force should consider approaching the motion picture industry to produce a film

Electromechanical Actuation Feasibility Study

DTIC Science & Technology

1976-05-01

FORMA11ON SLRVicE U. S. DPMfmft1 OF COMMOM AmR 703CR IIGRT DYNAM1U8 LABORATOY AMR 706C YST TM- COMMAND\\ ~WRIGUT-PATTEAWNk AIR POW= RASL OHIO 45M8...AMIE AND0 ACGRIESS 52 RIEPOR01T DATE Air Force Flight Dy-namics Labcratory May 1976 AFSC/AFWAL, United States Air Force 11 sNjsBsIm OF PAGIES Wright... Air Force under Contract Fý3615-75-C-305, Electronechanical Actuation Feasibility Study. The contract was aaministereu by the Air Force Flioht Dynamics

United States Air Force 611th Air Support Group/Civil Engineering Squadron Elmendorf AFB, Alaska. Remedial investigation and feasibility study. Bullen Point Radar Installation, Alaska. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karmi, S.

1996-03-18

The United States Air Force (Air Force) has prepared this Remedial investigation/Feasibility Study (RI/FS) report as part of the Installation Restoration Program (IRP) to present results of RI/FS activities at five sites at the Bullen Point radar installation. The IRP provides for investigating, quantifying, and remediating environmental contamination from past waste management activities at Air Force installations throughout the United States.

Design and Implementation of the Combined Federal Campaign Collection System.

DTIC Science & Technology

1987-12-01

Combined Federal Campaign Collection System THESIS 1 Frank L. Ucman Captain, USAF [ AFIT/GCS/ENG/87D.27 ’ii DEPARTMENT OF THE AIR FORCE LI AIR UNIVERSITY... AIR FORCE INSTITUTE OF TECHNOLOGY ii Wright-Patterson Air Force Base, Ohio DISTMIUTION STATMV1ENT A r 4 Approved for public r~~;8 6 ~ 3...of the Combined Federal Campaign Collection System THESIS I Presented to the Faculty of the School of Engineering of the Air Force Institute of

Air Force Global Weather Central System Architecture Study. Final System/Subsystem Summary Report. Volume 8. System Specification

DTIC Science & Technology

1976-03-01

Service , CSE, Scott AFB, IL 62225. aws, usaf ltr dtd 8 jul 1976 >- a. CD SYSTEM DEVELOPMENT CORPORATION 1/ 2500 Colorado Avenue Santa Monica...Government Agen-TfAf* 17 MAR 1976 cies only. Other requests for this document ’-^ must be referred to Air Weather Service /CSi^,, Scott Air Force...Air Force Communica- tions Service must be clear’y defined. The appropriate Air Force Conmunications Service Agency should be responsible for the

A Dynamic Computer Model to Examine Selected Effects of 304XX Career Field Consolidation.

DTIC Science & Technology

1982-09-01

DEPARTMENT OF THE AIR FORCED AIR UNIVERSITY (ATC) -; AIR FORCE INSTITUTE OF TECHNOLOGY D" "-gil tio "-: -I- -.- hA-W ig tP ttro Air, .’ Force Bas...The contents of tihe document are technically accurate, and no sensitive item., detrimeatal Ideas, or deleteriqu information are contained...ADDRESS O. PNOGAM ELEMENT. PROJECT, TASKAPE • WOe,6U" NUMERmsacT Scho6l of Systems and Logistics .A W N. " Air Force Institute of Technology , WPAFB It

Environmental Assessment for Construction and Repair of Fuel Storage and Offloading Facilities at Kirtland Air Force Base

DTIC Science & Technology

2005-09-01

G Ot-T GOO) D. BRENT WILSON, P.E. Base Civil Engineer Kirtland Air Force Base Kirtland AFB Fuel Storage and Ofjloading Facilities Construction...September 2005 A-1 3 77 MSG/CEVQ DEPARTMENT OF THE AIR FORCE 3 77th Civil Engineer Division (AFMC) 2050 Wyoming Blvd SE, Suite 120 Kirtland AFB NM...FINAL FINDING OF NO SIGNIFICANT IMPACT FOR THE FOR CONSTRUCTION AND REP AIR OF FUEL STORAGE AND OFFLOADING FACILITIES AT KIRTLAND AIR FORCE

Fraternization in the United States Air Force: Development of a Policy Booklet

DTIC Science & Technology

1988-09-01

perspective. Military custom, the UCMJ, military court decisions, and administrative actions have all played impor- tant roles in defining and enforcing a...your contribution. Good luck on publishing your work. Good job! We need it in the field !" Maj David Barton Chief. Military Affairs. Hq ATC JAG Office...GSM/LSR/88S-5 DEPARTMENT OF THE AIR FORCE AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY Wright-Patterson Air Force Base, Ohio DISTPJBU1• )N

32 CFR 631.15 - Air Force policy.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 4 2010-07-01 2010-07-01 true Air Force policy. 631.15 Section 631.15 National... INVESTIGATIONS ARMED FORCES DISCIPLINARY CONTROL BOARDS AND OFF-INSTALLATION LIAISON AND OPERATIONS Off-Installation Operations (Military Patrols and Investigative Activities) and Policy § 631.15 Air Force policy...

77 FR 41165 - Notice of Meeting of the Agricultural Air Quality Task Force

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-12

... Agricultural Air Quality Task Force AGENCY: Natural Resources Conservation Service, USDA. ACTION: Notice of meeting. SUMMARY: The Department of Agriculture (USDA), Agricultural Air Quality Task Force (AAQTF) will.../Concerns Discussion Continued discussion of goals for Task Force Anaerobic Digester Technologies Odor...

Phillips Laboratory Geophysics Scholar Program

DTIC Science & Technology

1993-09-30

research at Phillips Laboratory . Research sponsored by Air Force Geophysics Laboratory ...Geophysics Laboratory (now the Phillips Laboratory , Geophysics Directorate), United States Air Force for its sponsorship of this research through the Air ...September 1993 Approved for public release; distribution unlimited PHILLIPS LABORATORY Directorate of Geophysics AIR FORCE MATERIEL COMMAND

The Soviet Air Force and Strategic Bombing

DTIC Science & Technology

1999-04-01

to envision a British Air Force that could be totally divorced from some form of ground support role. Consequently, he saw an air campaign that would...CA: Presidio Press, 1986. Black, Steven K. The Icarus Illusion: Technology, Doctrine and the Soviet Air Force. Monterrey , CA, 1986. Cockburn, Andrew

Cost-effectiveness of forced air warming during sedation in the cardiac catheterisation laboratory.

PubMed

Conway, Aaron; Duff, Jed; Sutherland, Joanna

2018-05-13

To determine the cost-effectiveness of forced air warming during sedation in a cardiac catheterisation laboratory. Forced air warming improves thermal comfort in comparison with standard care. It is not known whether the extra costs required for forced air warming are good value. Cost-effectiveness analysis alongside a randomised controlled trial conducted in 2016-2017. A cost-effectiveness analysis was undertaken using Monte Carlo simulations from input distributions to estimate costs and effects associated with using forced air warming to reduce risk of thermal discomfort for patients receiving sedation in a cardiac catheterisation laboratory. A range of willingness to pay threshold values were tested with results plotted on a cost-effectiveness acceptability curve. Costs were calculated in Australian currency ($AUD). Estimated total costs were $5.21 (SD 3.26) higher per patient for forced air warming in comparison to standard care. Estimated probability of success (rating of thermal comfort) was 0.16 (0.06) higher for forced air warming. Forced air warming becomes more likely to result in a net benefit than standard care at a willingness to pay threshold of $34. Forced air warming could be considered cost-effective for procedures performed with sedation in a cardiac catheterisation laboratory if the extra cost of an incremental gain in thermal comfort is less than the decision maker's willingness to pay for it. Therefore, those responsible for decision-making regarding use of forced air warming in the cardiac catheterisation laboratory can use results of our model to decide if it represents good value for their organisation. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Effects of self-selected music on strength, explosiveness, and mood.

PubMed

Biagini, Matthew S; Brown, Lee E; Coburn, Jared W; Judelson, Daniel A; Statler, Traci A; Bottaro, Martim; Tran, Tai T; Longo, Nick A

2012-07-01

There has been much investigation into the use of music as an ergogenic aid to facilitate physical performance. However, previous studies have primarily focused on predetermined music and aerobic exercise. The purpose of this study was to investigate the effects of self-selected music (SSM) vs. those of no music (NM) on the mood and performance of the athletes performing bench press and squat jump. Twenty resistance trained collegiate men completed 2 experimental conditions, one while listening to SSM and the other with NM. The subjects reported their profile of mood states (POMS) and rating of perceived exertion (RPE) before and after performing 3 sets to failure of the bench press at 75% 1 repetition maximum (1RM) and 3 reps of the squat jump at 30% 1RM. Statistical analyses revealed no differences in squat jump height or relative ground reaction force, but the takeoff velocity (SSM-2.06 ± 0.17 m·s(-1); NM-1.99 ± 0.18 m·s(-1)), rate of velocity development (SSM-5.92 ± 1.46 m·s(-2); NM-5.63 ± 1.70 m·s(-2)), and rate of force development (SSM-3175.61 ± 1792.37 N·s(-1); NM-2519.12 ± 1470.32 N·s(-1)) were greater with SSM, whereas RPE (SSM-5.71 ± 1.37; NM-6.36 ± 1.61) was greater with NM. Bench press reps to failure and RPE were not different between conditions. The POMS scores of vigor (SSM-20.15 ± 5.58; NM-17.45 ± 5.84), tension (SSM-8.40 ± 3.99; NM-6.07 ± 3.26), and fatigue (SSM-8.65 ± 4.49; NM-7.40 ± 4.38) were greater with SSM. This study demonstrated increased performance during an explosive exercise and an altered mood state when listening to SSM. Therefore, listening to SSM might be beneficial for acute power performance.

Modular mechatronic system for stationary bicycles interfaced with virtual environment for rehabilitation.

PubMed

Ranky, Richard G; Sivak, Mark L; Lewis, Jeffrey A; Gade, Venkata K; Deutsch, Judith E; Mavroidis, Constantinos

2014-06-05

Cycling has been used in the rehabilitation of individuals with both chronic and post-surgical conditions. Among the challenges with implementing bicycling for rehabilitation is the recruitment of both extremities, in particular when one is weaker or less coordinated. Feedback embedded in virtual reality (VR) augmented cycling may serve to address the requirement for efficacious cycling; specifically recruitment of both extremities and exercising at a high intensity. In this paper a mechatronic rehabilitation bicycling system with an interactive virtual environment, called Virtual Reality Augmented Cycling Kit (VRACK), is presented. Novel hardware components embedded with sensors were implemented on a stationary exercise bicycle to monitor physiological and biomechanical parameters of participants while immersing them in an augmented reality simulation providing the user with visual, auditory and haptic feedback. This modular and adaptable system attaches to commercially-available stationary bicycle systems and interfaces with a personal computer for simulation and data acquisition processes. The complete bicycle system includes: a) handle bars based on hydraulic pressure sensors; b) pedals that monitor pedal kinematics with an inertial measurement unit (IMU) and forces on the pedals while providing vibratory feedback; c) off the shelf electronics to monitor heart rate and d) customized software for rehabilitation. Bench testing for the handle and pedal systems is presented for calibration of the sensors detecting force and angle. The modular mechatronic kit for exercise bicycles was tested in bench testing and human tests. Bench tests performed on the sensorized handle bars and the instrumented pedals validated the measurement accuracy of these components. Rider tests with the VRACK system focused on the pedal system and successfully monitored kinetic and kinematic parameters of the rider's lower extremities. The VRACK system, a virtual reality mechatronic bicycle rehabilitation modular system was designed to convert most bicycles in virtual reality (VR) cycles. Preliminary testing of the augmented reality bicycle system was successful in demonstrating that a modular mechatronic kit can monitor and record kinetic and kinematic parameters of several riders.

Airlift Cargo Hub Port Hold Times: Controlling Variations in Defense Supply Chain Delivery

DTIC Science & Technology

2010-06-01

AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY Wright-Patterson Air Force Base, Ohio APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED...Department of Operational Sciences Graduate School of Engineering and Management Air Force Institute of Technology Air University Air...process for a seamless flow of cargo onto the aircraft segment (AMC and DDC , 24 Sep 08). Figure 6 AMC Velocity Efforts (Anderson D. , 2009) While

Exploiting the Automatic Dependent Surveillance-Broadcast System via False Target Injection

DTIC Science & Technology

2012-03-01

THESIS Domenic Magazu III, Captain, USAF AFIT/GCO/ENG/12-07 DEPARTMENT OF THE AIR FORCE AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY...Department of Electrical and Computer Engineering Graduate School of Engineering and Management Air Force Institute of Technology Air University Air...of GNU Radio, a Universal Software Radio Peripheral (USRP), and software developed by the author. The ability to generate, transmit, and insert

Using Covert Means to Establish Cybercraft Command and Control

DTIC Science & Technology

2009-03-01

unknown entity. This mimics human trust patterns in many ways [15]. Take for example a human trying to find 10 a new auto mechanic or a new babysitter ...AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY Wright-Patterson Air Force Base, Ohio APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED. The views...Department of Electrical and Computer Engineering Graduate School of Engineering and Management Air Force Institute of Technology Air University Air

Clinical factors affecting inspired gas humidification and oral dryness during noninvasive ventilation.

PubMed

Oto, Jun; Imanaka, Hideaki; Nishimura, Masaji

2011-10-01

Oral dryness is a common complication during noninvasive ventilation (NIV). We measured the oral dryness of patients and performed a bench study to investigate factors related to humidification during NIV. Patients were randomly assigned into 2 groups: medium (Med group) and maximum (Max group) heated humidifier (HH) settings. Oral moistness was measured using an oral moisture-checking device, and the feeling of oral dryness was evaluated using a 0 to 10 numerical rating scale (NRS) at 0, 12, and 24 hours from the beginning of NIV and at 12 and 24 hours after NIV was discontinued. A bench study was performed to assess the effects of positive end-expiratory pressure (PEEP), the fraction of inspired oxygen (F(I)O(2)), and air leaks on absolute humidity. We evaluated 3 HH settings: no HH, HH at the medium setting, and HH at the maximum setting. The temperature in the outlet chamber was 31°C to 32°C for the medium HH setting and 38°C to 41°C for the maximum HH setting. In the clinical study, 12 patients were assigned to the Med group and 11 to the Max group. In the Med group, oral moistness decreased and NRS increased at 12 and 24 hours compared with 0 hours (P < .05). In the Max group, neither the oral moistness nor the NRS changed throughout the study period, whereas in the bench study, high F(I)O(2), high PEEP, and air leak decreased the absolute humidity for both HH settings (P < .01). However, it is not clear to what extent these factors affected the patients' oral dryness because the ranges of F(I)O(2) and PEEP were narrow. Oral dryness was a common problem in our patients. The HH setting significantly affected humidification and oral dryness during NIV. Copyright © 2011 Elsevier Inc. All rights reserved.

Air Force TV

Science.gov Websites

Speeches Archive Former AF Top 3 Viewpoints and Speeches Air Force Warrior Games 2017 Events 2018 Air Force Strategic Documents Desert Storm 25th Anniversary Observances DoD Warrior Games Portraits in Courage

Air Force Senior Leaders

Science.gov Websites

Speeches Archive Former AF Top 3 Viewpoints and Speeches Air Force Warrior Games 2017 Events 2018 Air Force Strategic Documents Desert Storm 25th Anniversary Observances DoD Warrior Games Portraits in Courage

Air Force Radio News

Science.gov Websites

Speeches Archive Former AF Top 3 Viewpoints and Speeches Air Force Warrior Games 2017 Events 2018 Air Force Strategic Documents Desert Storm 25th Anniversary Observances DoD Warrior Games Portraits in Courage

SOUTHEAST AND NORTHEAST SIDES. Looking west Edwards Air Force ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

SOUTHEAST AND NORTHEAST SIDES. Looking west - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Fuel & Water Tank, Test Area 1-115, northwest end of Saturn Boulevard, Boron, Kern County, CA

Transformation in the French Air Force in an Era of Change

DTIC Science & Technology

2008-01-01

Abria.indd 6 10/30/08 1:15:37 PM Transformation in the French Air Force in an Era of Change Général d’armée aérienne Stéphane Abrial, chef...l’armée l’air,” sponsored by the Centre d’études stratégiques aérospatiales, 3 June 2008. The French Air Force, like all defense organizations...related to our equipment, because the French aircraft Gen Stéphane Abrial is the chief of staff of the French Air Force. He completed the French Air

78 FR 10127 - Request for Nominations to the Agricultural Air Quality Task Force

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-13

... Conservation Service Request for Nominations to the Agricultural Air Quality Task Force AGENCY: Natural... Nominations to the Agricultural Air Quality Task Force. SUMMARY: The Secretary of Agriculture invites... Force (AAQTF) which was established by the Federal Agriculture Improvement and Reform Act of 1996 to...

32 CFR 644.327 - Air Force military real property.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 32 National Defense 4 2010-07-01 2010-07-01 true Air Force military real property. 644.327 Section... Force military real property. Military real property under the control of the Department of the Air Force will be placed in excess status as outlined in AFR 87-4. ...

32 CFR 855.5 - Responsibilities and authorities.

Code of Federal Regulations, 2012 CFR

2012-07-01

... aircraft use of Air Force airfields, subject to the laws and regulations of the US, or to applicable international agreements (e.g., status of forces agreements) with the country in which the Air Force... 855.5 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL...

32 CFR 855.5 - Responsibilities and authorities.

Code of Federal Regulations, 2013 CFR

2013-07-01

... aircraft use of Air Force airfields, subject to the laws and regulations of the US, or to applicable international agreements (e.g., status of forces agreements) with the country in which the Air Force... 855.5 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL...

32 CFR 855.5 - Responsibilities and authorities.

Code of Federal Regulations, 2014 CFR

2014-07-01

... aircraft use of Air Force airfields, subject to the laws and regulations of the US, or to applicable international agreements (e.g., status of forces agreements) with the country in which the Air Force... 855.5 National Defense Department of Defense (Continued) DEPARTMENT OF THE AIR FORCE AIRCRAFT CIVIL...

The Miniaturization of the AFIT Random Noise Radar

DTIC Science & Technology

2013-03-01

RANDOM NOISE RADAR I. Introduction Recent advances in technology and signal processing techniques have opened thedoor to using an ultra-wide band random...AIR FORCE INSTITUTE OF TECHNOLOGY Wright-Patterson Air Force Base, Ohio DISTRIBUTION STATEMENT A. APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED...and Computer Engineering Graduate School of Engineering and Management Air Force Institute of Technology Air University Air Education and Training

76 FR 82317 - Federal Property Suitable as Facilities To Assist the Homeless

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-30

..., Contamination 22 Bldgs. Military Family Housing Little Rock AR 72099 Landholding Agency: Air Force Property... landholding agencies at the following addresses: Air Force: Mr. Robert Moore, Air Force Real Property Agency... Carolina Marine Corps Air Station 3481 TRASK Parkway Beaufort SC 29904 Landholding Agency: GSA Property...

75 FR 48929 - Notice of Meeting of the Agricultural Air Quality Task Force

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-12

... Agricultural Air Quality Task Force AGENCY: Natural Resources Conservation Service (NRCS), United States... Triangle Park, North Carolina 27711; (919) 541-5400. The Agricultural Air Quality Task Force (AAQTF) will meet to continue discussions on air quality issues relating to agriculture. Additionally, the Livestock...

40 CFR Appendix Vii to Part 86 - Standard Bench Cycle (SBC)

Code of Federal Regulations, 2014 CFR

2014-07-01

... VII to Part 86—Standard Bench Cycle (SBC) 1. The standard bench aging durability procedures [Ref. § 86.1823-08(d)] consist of aging a catalyst-oxygen-sensor system on an aging bench which follows the standard bench cycle (SBC) described in this appendix. 2. The SBC requires use of an aging bench with an...

32 CFR Appendix B to Part 68 - Addendum for Education Services Between [Name of Educational Institution] and the U.S. Air Force

Code of Federal Regulations, 2013 CFR

2013-07-01

... Educational Institution] and the U.S. Air Force B Appendix B to Part 68 National Defense Department of Defense...] and the U.S. Air Force 1. Purpose. This addendum is between (Name of Educational Institution), hereafter referred to as the “Institution,” and the United States Air Force (USAF). The purpose of this...

The Official Home Page of the U.S. Air Force

Science.gov Websites

: May 24 Air Force directs one-day operational safety review SecAF LOI SecAF LOI Letter of Intent AF and members using two C-130 and one C-17 training airframes. (U.S. Air Force photo by Richard Eldridge) The Transport Team crew members using two C-130 and one C-17 training airframes. (U.S. Air Force photo by

Comparison of Two Methods of Obtaining Digital Orthodontic Models: Direct vs. Indirect

DTIC Science & Technology

2013-05-17

companies whose materials are discussed in this article. DEPARTMENT OF THE AIR FORCE AIR FORCE POST GRADUATE DENTAL SCHOOL ORTHODONTIC FLIGHT 2133...Orthodontic Residency Program Air Force Post Graduate Dental School Date: 06/06/13 Uniformed Services University of the Health Sciences Manuscript...Science in Oral Biology 3. School/Department/Center: Air Force Postgraduate Dental School (AFPDS), Tri- Service Orthodontic Dental School 4. Phone: (210

Water Vulnerability Assessments

DTIC Science & Technology

1991-04-01

Air Force Base , Texas 78235-5000 B AApril 1991 MAY f2-D T Final ReportBo R ’V Approved for public release...dilstribution Is unlimited. 91-00493 91 524 020 IIlI 111III II AIR FORCE SYSTEMS COMMAND SBROOKS AIR FORCE BASE , TEXAS 78235-5000 NOTICES When Government...tornadoes. If the base is on a fault line, they should do an assessment for earthquakes. Air Force plans should include sabotage, biological,

A Retrospective Analysis of Initial Posterior Root Canal Therapy on United States Air Force Personnel

DTIC Science & Technology

2016-06-01

and John Yaccino, DDS Abstract Introduction: The Air Force Dental Service (AFDS) has established evidence-based treatment standards for endodontics...and cuspal coverage restorations (4-6). With this research, the Air Force Dental Service (AFDS) established evidence-based treatment standards for...endodontics to ensure Airmen receive high-quality, safe dental care (7). These standards are taught at the two Air Force (AF) Postgraduate Endodontic

How Does the Air Force Create Effective Accountability for Initial Spares?

DTIC Science & Technology

1990-05-01

effective accountability for initial spares? AUTHOR: Pamela J. Henson, Civilian, USAF The accountability for acquisition cost , schedule, and...in place to allow the Program Manager to effectively manage this cost element. Initial spares have traditionally been managed in Air Force Logistics...at Maxwell Air Force Base. Pamela became the Chief, Cost Analysis Division at HQ Air Force Logistics Command in 1987, where she received the Civilian

Canadian Air Force Leadership and Command: Implications for the Human Dimension of Expeditionary Air Force Operations

DTIC Science & Technology

2006-11-01

Project Manager : CSA: Angela Febbraro The scientific or technical validity of this Contract Report is entirely the responsibility of the...ways, for example, in leadership styles and command arrangements. Unfortunately for the Canadian Air Force, very little has been written about how its...culture and professional working environment have influenced the development of unique Canadian air force leadership styles and command

Environmental Baseline Survey for Three Sites at TRW Capistrano Test Site, California

DTIC Science & Technology

1999-11-01

by Headquarters Space and Missile Systems Center Los Angeles Air Force Base, California Report Documentation Page Report Date 00111999 Report Type N...and Address(es) Headquarters Space and Missile Systems Center Los Angeles Air Force Base, California Performing Organization Report Number...Sponsoring/Monitoring Agency Name(s) and Address(es) Department of the Air Force Headquarters Space and Missile Systems Center, Los Angeles Air Force Base

MOLECULAR DYNAMICS SIMULATION AND EXPERIMENTAL STUDIES OF GOLD NANOPARTICLE TEMPLATED HDL-LIKE NANOPARTICLES FOR CHOLESTEROL (POSTPRINT)

DTIC Science & Technology

2016-12-21

STINFO COPY) AIR FORCE RESEARCH LABORATORY MATERIALS AND MANUFACTURING DIRECTORATE WRIGHT-PATTERSON AIR FORCE BASE, OH 45433-7750 AIR FORCE MATERIEL...9. SPONSORING/MONITORING AGENCY NAME(S) AND ADDRESS(ES) 10. SPONSORING/MONITORING AGENCY ACRONYM(S) Air Force Research Laboratory...removing excess cholesterol from arterial plaques. Gold nanoparticles (AuNPs) functionalized with apolipoprotein A-I and with the lipids 1,2

Final Environmental Assessment for Low-Level Flight Testing, Evaluation, and Training, Edwards Air Force Base

DTIC Science & Technology

2005-05-01

4. TITLE AND SUBTITLE Final Environmental Assessment for Low-Level Flight Testing, Evaluation, and Training, Edwards Air Force Base 5a. CONTRACT...NAME(S) AND ADDRESS(ES) Air Force Flight Test Center,Environmental Management Directorate,Edwards AFB,CA,93524 8. PERFORMING ORGANIZATION REPORT...DISTRIBUTION/AVAILABILITY STATEMENT Approved for public release; distribution unlimited 13. SUPPLEMENTARY NOTES 14. ABSTRACT The U.S. Air Force Flight Test

Cognitive Evaluation of Israeli Air Force Pilot Cadets.

PubMed

Gordon, Shirley; Goren, Chen; Carmon, Erez; Shelef, Leah

2017-04-01

In aviation psychology, there is a constant need for the cognitive evaluation of pilots as part of operational fitness and safety criteria. A cross-sectional study with comparison between the performance of Israeli Air Force pilot cadets (N = 318) and U.S. Air Force pilot training candidates (N = 512) as assessed by a cognitive battery was undertaken. The data of the comparison group was collected from Callister, King, and Retzlaff, as published in 1996. In general, the means in the three components composing the battery-speed, accuracy, and throughput variables-indicated that the Israeli Air Force pilot cadets' scores were higher than those of the U.S. Air Force pilot candidates' scores in 50 of 53 variables. Nonsignificant differences were found in Accuracy of shifting attention-arrow color (SATAC), pathfinder-combined (PFC), and pathfinder-letter (PFL). The difference in performance between the two groups may be due to differences in population characteristics. However, these results need to be considered cautiously, as the groups were sampled at a sizeable time gap (1996 for the U.S. Air Force vs. 2013 for the Israeli Air Force), with each time period characterized by different cultural and technological influences.Gordon S, Goren C, Carmon E, Shelef L. Cognitive evaluation of Israeli Air Force pilot cadets. Aerosp Med Hum Perform. 2017; 88(4):392-398.

The Effects of Bench Press Variations in Competitive Athletes on Muscle Activity and Performance

PubMed Central

Saeterbakken, Atle Hole; Mo, Dag-André; Scott, Suzanne; Andersen, Vidar

2017-01-01

Abstract The aim of the study was to compare the EMG activity performing 6RM competition style bench press (flat bench-wide grip) with 1) medium and narrow grip widths on a flat bench and 1) inclined and declined bench positions with a wide grip. Twelve bench press athletes competing at national and international level participated in the study. EMG activity was measured in the pectoralis major, anterior and posterior deltoid, biceps brachii, triceps brachii and latissimus dorsi. Non-significant differences in activation were observed between the three bench positions with the exception of 58.5-62.6% lower triceps brachii activation, but 48.3-68.7% greater biceps brachii activation in the inclined bench compared with the flat and declined bench position. Comparing the three grip widths, non-significant differences in activations were observed, with the exception of 25.9-30.5% lower EMG activity in the biceps brachii using a narrow grip, compared to the medium and wide grip conditions. The 6-RM loads were 5.8-11.1% greater using a medium and wide grip compared to narrow grip width and 18.5-21.5% lower in the inclined bench position compared with flat and declined. Comparing the EMG activity during the competition bench press style with either the inclined and declined bench position (wide grip) or using a narrow and medium grip (flat bench), only resulted in different EMG activity in the biceps- and triceps brachii. The 6RM loads varied with each bench press variation and we recommend the use of a wide grip on a flat bench during high load hypertrophy training to bench press athletes. PMID:28713459

The Effects of Bench Press Variations in Competitive Athletes on Muscle Activity and Performance.

PubMed

Saeterbakken, Atle Hole; Mo, Dag-André; Scott, Suzanne; Andersen, Vidar

2017-06-01

The aim of the study was to compare the EMG activity performing 6RM competition style bench press (flat bench-wide grip) with 1) medium and narrow grip widths on a flat bench and 1) inclined and declined bench positions with a wide grip. Twelve bench press athletes competing at national and international level participated in the study. EMG activity was measured in the pectoralis major, anterior and posterior deltoid, biceps brachii, triceps brachii and latissimus dorsi. Non-significant differences in activation were observed between the three bench positions with the exception of 58.5-62.6% lower triceps brachii activation, but 48.3-68.7% greater biceps brachii activation in the inclined bench compared with the flat and declined bench position. Comparing the three grip widths, non-significant differences in activations were observed, with the exception of 25.9-30.5% lower EMG activity in the biceps brachii using a narrow grip, compared to the medium and wide grip conditions. The 6-RM loads were 5.8-11.1% greater using a medium and wide grip compared to narrow grip width and 18.5-21.5% lower in the inclined bench position compared with flat and declined. Comparing the EMG activity during the competition bench press style with either the inclined and declined bench position (wide grip) or using a narrow and medium grip (flat bench), only resulted in different EMG activity in the biceps- and triceps brachii. The 6RM loads varied with each bench press variation and we recommend the use of a wide grip on a flat bench during high load hypertrophy training to bench press athletes.

Identification of Chemicals of Interest to the Department of Defense and U.S. Air Force Among the U.S. Environmental Protection Agency’s Integrated Risk Information System Chemicals that are Due for Reassessment of their Toxicity Values

DTIC Science & Technology

2010-03-16

Exceeded at ERP Soil and Groundwater Sites 86 A-2a. Identification of IRIS Chemicals of Interest on the ATSDR CERCLA Priority List of Hazardous...the Number (Bold Font) of Air Force ERP Samples in Which They Were Detected 317 A-4d. Air Force ERP Soil Samples: IRIS Chemicals of Interest...Ranked by the Number (Bold Font) of Air Force ERP Soil Samples in Which They Were Detected 333 A-4e. Air Force ERP Groundwater Samples: IRIS Chemicals of

Secretary of the Air Force

Science.gov Websites

Speeches Archive Former AF Top 3 Viewpoints and Speeches Air Force Warrior Games 2017 Events 2018 Air Force Strategic Documents Desert Storm 25th Anniversary Observances DoD Warrior Games Portraits in Courage

The U.S. Air Force Aeromedical Evacuation Mission: A Mission for the Air Reserve Components

DTIC Science & Technology

2016-02-01

AU/ACSC/2016 AIR COMMAND AND STAFF COLLEGE AIR UNIVERSITY THE U.S. AIR FORCE AEROMEDICAL EVACUATION MISSION: A MISSION FOR THE AIR RESERVE...Aeromedical Evacuation ............................................................................................................. 7 The Current Problem...13 Evaluation

Seeing Off the Bear: Anglo-American Air Power Cooperation During the Cold War,

DTIC Science & Technology

1995-01-01

Force History and Museums Program United States Air Force Washington, D.C. 1995 .ApprovAd fox r’Thiic r ~elease, j,, 117-~ I 7,CTh D Disbution...Air Power History Symposium began in late 1992 under the direction of General Bryce Poe II, President of the Air Force Historical Foundation, Air...vii Introduction and Welcome General Bryce Poe II; Air Marshal Sir Frederick Sowrey .............. 3 Opening

KSC-07pd3083

NASA Image and Video Library

2007-11-02

KENNEDY SPACE CENTER, FLA. -- Visitors gather along the NASA Causeway to watch the U.S. Air Force Thunderbirds practicing for the World Space Expo Aerial Salute at NASA's Kennedy Space Center. Commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond, the expo will showcase various panels, presentations and educational programs, as well as the air show. Participating in the air show are the U.S. Air Force Thunderbirds, U.S. Air Force F-22 Raptor, U.S. Navy F-18 Super Hornet, U.S. Air Force F-15 Eagle, the P-51 Mustang Heritage Flight, and the U.S. Air Force 920th Rescue Wing, which was responsible for Mercury and Gemini capsule recovery. The U.S. Army Golden Knights will also demonstrate precision skydiving. Photo credit: NASA/George Shelton.

KSC-07pd3080

NASA Image and Video Library

2007-11-02

KENNEDY SPACE CENTER, FLA. -- During a rehearsal for the World Space Expo Aerial Salute at NASA's Kennedy Space Center, an honor guard from Patrick Air Force Base marches along the NASA Causeway. Commemorating humanity's first 50 years in space while looking forward to returning people to the moon and exploring beyond, the expo will showcase various panels, presentations and educational programs, as well as the air show. Participating in the air show are the U.S. Air Force Thunderbirds, U.S. Air Force F-22 Raptor, U.S. Navy F-18 Super Hornet, U.S. Air Force F-15 Eagle, the P-51 Mustang Heritage Flight, and the U.S. Air Force 920th Rescue Wing, which was responsible for Mercury and Gemini capsule recovery. The U.S. Army Golden Knights will also demonstrate precision skydiving. Photo credit: NASA/George Shelton.

High performance bilateral telerobot control.

PubMed

Kline-Schoder, Robert; Finger, William; Hogan, Neville

2002-01-01

Telerobotic systems are used when the environment that requires manipulation is not easily accessible to humans, as in space, remote, hazardous, or microscopic applications or to extend the capabilities of an operator by scaling motions and forces. The Creare control algorithm and software is an enabling technology that makes possible guaranteed stability and high performance for force-feedback telerobots. We have developed the necessary theory, structure, and software design required to implement high performance telerobot systems with time delay. This includes controllers for the master and slave manipulators, the manipulator servo levels, the communication link, and impedance shaping modules. We verified the performance using both bench top hardware as well as a commercial microsurgery system.

Environmental Assessment: Western Range Instrumentation Modernization Program Vandenberg Air Force Base, Santa Barbara County, and Pillar Point Air Force Station, San Mateo County California

DTIC Science & Technology

2008-09-03

Force Base ( AFB ), and Pillar Point Air Force Station (AFS), California. The 30th Space Wing at Vandenberg AFB operates the Western Launch and Test...Range (Western Range). The Western Range begins at the coastal boundaries of Vandenberg AFB and extends westward to the Marshall Islands, including...Vandenberg AFB . Vandenberg AFB is headquarters to the 30th Space Wing, the Air Force Space Command unit that operates Vandenberg AFB and the Western

Grounds Management Cost Reduction Strategies

DTIC Science & Technology

1993-06-01

AIR FORCE BASE , FLORIDA 32403-5319 1 REPORT DOCUMENTATION PAGE OMI No. 07o o’m €0k ’oJO flm4’¢• htu mgI• t O•t•f~ • ’h )fel •0W ll:• ll... FORCE INPUTS Approximately 130 ideas were submitted by individuals at Air Force MAJCOMs and bases . These ideas were reviewed by a team of Air Force ...contractor to use base Z - $ 1,200 dumpsters for reuse collection from policing operations. A-2-5 AIR FORCE GROUNDS RITU COST RIEDCTION

United States Air Force 611th Air Support Group/Civil Engineering Squadron, Elmendorf AFB, Alaska. Decision document for no further response action planned Oliktok Point Radar Installation, Alaska. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karmi, S.

1996-06-03

This Decision Document discusses the selection of no further action as the recommended action for four sites located at the Oliktok Point radar installation. The United States Air Force (Air Force) completed a Remedial Investigation/Feasibility Study and a Risk Assessment for the eight sites located at the Oliktok Point installation (U.S. Air Force 1996a,b). Based on the findings of these activities, four sites are recommended for no further action.

Report of Investigation: The Presence of Biological and Chemical Warfare Materiel at AFMC Bases within the United States

DTIC Science & Technology

2000-06-01

knew nothing of the BW/CW work done on the base in the 40’ s and 50’ s . 461 History of the Armament Development and Test Center, Appendix B, 1 July 1970...technical report has been reviewed and is approved for publication. FOR THE DIRECTOR ALBERT S . TORdGIAN, Lt Col, US Deputy Chief, Deployment and Su...Office of History , Air Force Materiel Command Air Force Systems Command Air Force Special Weapons Center Air Force Weapons Laboratory Air Materiel

Measuring Scaling Effects in Small Two-Stroke Internal Combustion Engines

DTIC Science & Technology

2014-06-20

Figure 17. The engines ingest air /fuel mixture through a dual mixing screw carburetor to the crankcase. Crankcase compression drives the scavenging...Alex K. Rowton, Captain, USAF AFIT-ENY-T-14-J-36 DEPARTMENT OF THE AIR FORCE AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY Wright...Patterson Air Force Base, Ohio DISTRIBUTION STATEMENT A. APPROVED FOR PUBLIC RELEASE; DISTRIBUTION UNLIMITED. The views expressed

Air Force Technical Objective Document FY 87

DTIC Science & Technology

1985-12-01

Air Force Systems Command Edwards Air Force Base. Cal ifornia 93523-5000 NOTICES THIS DOCUMENT IS FOR INFORMATION AND GUIDANCE ONL Y This...acquisition of Air Foree weapon systems . Each Air Foree laboratory annually formulates Q Research and Technology (R& T) Pion in response to available...guidance based on USAF requirements, the identification of scientific and technological opportunities, and the needs of present and projected systems

F-22 Operational Squadron and T-38 Detachment Beddown at Tyndall Air Force Base, Florida

DTIC Science & Technology

2011-08-01

tactics, radar employment, identification, weapons employment, defensive response, electronic countermeasures, and electronic counter...use, and electronic countermeasures. Warning Area, MOA, and ATCAA 2,000 AGL to 60,000 MSL 0.75 to 1.5 hour (Dissimilar) Air Combat...night), air refueling, and strike-force rendezvous, conducting air-to-ground strikes, strike force defense and escort, air intercepts, electronic

Air Force and Diversity: The Awkward Embrace

DTIC Science & Technology

2013-02-14

Streeter is a U.S. Air Force intelligence officer assigned to the Air War College, Air University, Maxwell AFB, AL. She graduated from the United States...future leaders.” Princeton University Office of Human Resources Web site; Wilson et al, Grooming Top Leaders, 4. 28 45. Dr Fil J . Arenas...Air Force Diversity Strategic Roadmap (2012), 14. 86. Dr. Fil J . Arenas (Associate Professor, Organizational Leadership Studies, Squadron

Bench Evaluation of Four Portable Oxygen Concentrators Under Different Conditions Representing Altitudes of 2438, 4200, and 8000 m.

PubMed

Bunel, Vincent; Shoukri, Amr; Choin, Frederic; Roblin, Serge; Smith, Cindy; Similowski, Thomas; Morélot-Panzini, Capucine; Gonzalez, Jesus

2016-12-01

Bunel, Vincent, Amr Shoukri, Frederic Choin, Serge Roblin, Cindy Smith, Thomas Similowski, Capucine Morélot-Panzini, and Jésus Gonzalez. Bench evaluation of four portable oxygen concentrators under different conditions representing altitudes of 2438, 4200, and 8000 m. High Alt Med Biol. 17:370-374, 2016.-Air travel is responsible for a reduction of the partial pressure of oxygen (O 2 ) as a result of the decreased barometric pressure. This hypobaric hypoxia can be dangerous for passengers with respiratory diseases, requiring initiation or intensification of oxygen therapy during the flight. In-flight oxygen therapy can be provided by portable oxygen concentrators, which are less expensive and more practical than oxygen cylinders, but no study has evaluated their capacity to concentrate oxygen under simulated flight conditions. We tested four portable oxygen concentrators during a bench test study. The O 2 concentrations (FO 2 ) produced were measured under three different conditions: in room air at sea level, under hypoxia due to a reduction of the partial pressure of O 2 (normobaric hypoxia, which can be performed routinely), and under hypoxia due to a reduction of atmospheric pressure (hypobaric hypoxia, using a chamber manufactured by Airbus Defence and Space). The FO 2 obtained under conditions of hypobaric hypoxia (chamber) was lower than that measured in room air (0.92 [0.89-0.92] vs. 0.93 [0.92-0.94], p = 0.029), but only one portable oxygen concentrator was unable to maintain an FO 2 ≥ 0.90 (0.89 [0.89-0.89]). In contrast, under conditions of normobaric hypoxia (tent) simulating an altitude of 2438 m, none of the apparatuses tested was able to achieve an FO 2 greater than 0.76. (0.75 [0.75-0.76] vs. 0.93 [0.92-0.94], p = 0.029). Almost all portable oxygen concentrators were able to generate a sufficient quantity of O 2 at simulated altitudes of 2438 m and can therefore be used in the aircraft cabin. Unfortunately, verification of the reliability and efficacy of these devices in a patient would require a nonroutinely available technology, and no preflight test can currently be performed by using simple techniques such as hypobaric hypoxia.

Petrography and geochemistry of the San Miguel lignite, Jackson Group (Eocene), south Texas

USGS Publications Warehouse

Warwick, Peter D.; Crowley, Sharon S.; Ruppert, Leslie F.; Pontolillo, James

1996-01-01

The San Miguel lignite deposit (late Eocene, lower Jackson Group) of south Texas consists of four or more thin (generally < 1 m thick) lignite benches that are separated by claystone and mudstone partings. The partings are composed of altered volcanic air-fall ash that has been reworked by tidal or channel processes associated with a back-barrier depositional environment. The purpose of this study is to examine the relationship between the ash yield and the petrographic and geochemical characteristics of the San Miguel lignite as mined. Particular attention is given to 12 of the environmentally sensitive trace elements (As, Be, Cd, Cr, Co, Hg, Mn, Ni, Pb, Sb, Se, and U) that have been identified as possible hazardous air pollutants (HAPs) by the United States Clean Air Act Amendments of 1990. A total of 29 rock and lignite samples were collected and characterized by geochemical and petrographic methods. The major conclusions of the study are as follows: (1) The distribution of Mn is inversely related to the ash yield of the lignite samples. This indicates an organic affinity, or an association with finely disseminated minerals in the lignite that contain this element. (2) On a whole-coal basis, the concentration of the HAPs' element Pb is positively related to ash yield in lignite samples. This indicates an inorganic affinity for Pb. (3) Average whole-coal concentrations of As, Be, Sb, and U in the San Miguel samples are greater than published averages for these elements in other U.S. lignites. (4) The upper and lower lignite benches of the San Miguel deposit are both ash- and algal-rich, indicating that these intervals were probably deposited in wetter conditions than those in which the middle intervals formed. (5) The dominance of the eugelinite maceral subgroup over the huminite subgroup indicates that the San Miguel lignites were subjected to peat-forming conditions (either biogenic or chemical) that enabled degradation of wood cellular material into matrix gels, or that the plants that formed these lignite benches were less woody and more prone to formation of matrix gels. (6) An inertinite-rich layer (top of the B bed) might have formed from widespread oxidation of the San Miguel peat as a result of a volcanic ash fall which was subsequently reworked.

Chief of Staff of the Air Force

Science.gov Websites

Speeches Archive Former AF Top 3 Viewpoints and Speeches Air Force Warrior Games 2017 Events 2018 Air Force Strategic Documents Desert Storm 25th Anniversary Observances DoD Warrior Games Portraits in Courage

Chief Master Sergeant of the Air Force

Science.gov Websites

Speeches Archive Former AF Top 3 Viewpoints and Speeches Air Force Warrior Games 2017 Events 2018 Air Force Strategic Documents Desert Storm 25th Anniversary Observances DoD Warrior Games Portraits in Courage

4. BUILDING 8767, INTERIOR. Looking west. Edwards Air Force ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. BUILDING 8767, INTERIOR. Looking west. - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Observation Bunkers for Test Stand 1-A, Test Area 1-120, north end of Jupiter Boulevard, Boron, Kern County, CA

Focused Logistics; What the Air Force Brings to the Fight

DTIC Science & Technology

2002-04-09

Agency partnered to develop a Strategic Distribution Management Initiative that support the Air Force’s logistics transformation and is linked by Global Command and Control System and Global Combat Support System-Air Force.

DETAIL, CONTROL BOOTH, RP1 TANK FARM Edwards Air Force ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL, CONTROL BOOTH, RP1 TANK FARM - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Combined Fuel Storage Tank Farm, Test Area 1-120, north end of Jupiter Boulevard, Boron, Kern County, CA

Air Force Health Study. An Epidemiologic Investigation of Health Effects in Air Force Personnel Following Exposure to Herbicides. Volume 1

DTIC Science & Technology

1991-03-01

found to be significantly associated with coordination and a central nervous system index, but cranial nerve function and peripheral nerve status...AD-A237 516 Air Force Health Study A An Epidemiologic In vestigation of Health Effects in Air Force Personnel Following Exposure to Herbicides SAIC...Smeda SCIENCE APPLICATIONS EPIDEMIOLOGY RESEARCH DIVISION INTERNATIONAL CORPORATION ARMSTRONG LABORATORY 8400 Westpark Drive HUMAN SYSTEMS DIVISION

The Shock and Vibration Bulletin. Part 3. Invited Papers, Pyrotechnic Shock, Pyrotechnic Shock Workshop

DTIC Science & Technology

1986-08-01

Technology Laboratory, Watertown, MA AIR FORCE BASIC RESEARCH IN DYNAMICS AND CONTROL OF LARGE SPACE STRUCTURES Anthony K. Amos, Boiling Air Force Base...Engineering, Watchun$, NJ TEMPERATURE SHIFT CONSIDERATIONS FOR DAMPING MATERIALS L. Rogers, Air Force Wright Aeronautictl Laboratories, Wright...INDUCED CAVITY ACOUSTICS L.L. Shaw,. Air Force Wr4ht Aeroaauical Laborawrics, Wri•ht-Paucswon AFB. OH i 4i SESSION CHAIRMEN AND COCHAIRMEN 56th Shock and

Occupational Medical Surveillance Recommendations

DTIC Science & Technology

1991-07-01

categories of chemicals that may be in use at most Air Force bases . Areas of importance are the routes of exposure, target organs and health effects...1991 R Final Technical Report A T 0 R Approved for public release; distribution Is unlimited. Y 91-08239 AIR FORCE SYSTEMS COMMAND BROOKS AIR FORCE ...for illustration purposes and does not constitute endorsement or recommenda- tion for use by the United States Air Force . The Office of Public Affairs

Centennial Aerospace Power: The ’US Air Force’ at 100 Years

DTIC Science & Technology

2000-01-01

culture during this time will be based both on the national power status of the United States relative to the rest of the world as...must develop an information warrior culture . This culture must be information based and include the application of force through air, space, and cyber... The culture of the U.S. Air Force will have to expand from one of employing air and space forces to one of

Evaluation of Air Force and Navy Demand Forecasting Systems

DTIC Science & Technology

1994-01-01

forecasting approach, the Air Force Material Command is questioning the adoption of the Navy’s Statistical Demand Forecasting System ( Gitman , 1994). The...Recoverable Item Process in the Requirements Data Bank System is to manage reparable spare parts ( Gitman , 1994). Although RDB will have the capability of...D062) ( Gitman , 1994). Since a comparison is made to address Air Force concerns, this research only limits its analysis to the range of Air Force

Collaborative Multidisciplinary Sciences for Analysis and Design of Aerospace Vehicles. Volume 1

DTIC Science & Technology

2017-05-01

AEROSPACE VEHICLES Volume 1 5a. CONTRACT NUMBER FA8650-09-2-3938 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 62201F 6. AUTHOR(S) Raymond M...S) AND ADDRESS(ES) 8. PERFORMING ORGANIZATION REPORT NUMBERDesign and Analysis Branch (AFRL/RQVC) Aerospace Vehicles Division Air Force Research...Laboratory, Aerospace Systems Directorate Wright-Patterson Air Force Base, OH 45433-7542 Air Force Materiel Command, United States Air Force Virginia

Perceptual Performance Impact of GPU-Based WARP and Anti-Aliasing for Image Generators

DTIC Science & Technology

2016-06-29

with the Air Force Research Laboratory (AFRL) and NASA AMES, constructed the Operational Based Vision Assessment (OBVA) simulator. This 15-channel, 150...ABSTRACT In 2012 the U.S. Air Force School of Aerospace Medicine, in partnership with the Air Force Research Laboratory (AFRL) and NASA AMES...with the Air Force Research Laboratory (AFRL) and NASA AMES, constructed the Operational Based Vision Assessment (OBVA) simulator to evaluate the

Securing the High Ground: Dominant Combat Air Force for America. 2008 Combat Air Force Strategic Plan

DTIC Science & Technology

2008-07-28

continue to be beyond our technical ability to realize aggresively pursue advanced technical solutions to stay at the leading edge of technological...inherent to each caf Way and to seek continual improvement through exploration of innovative concepts, advanced capabilities, game -changing...available online at the air force portal: https://wwwd.my.af.mil/afknprod/strat_plan COMBAT AIR FORCE STRATEGIC PLAN Points of Contact securing the high

Ground-Based Midcourse Defense (GMD) Initial Defensive Operations Capability (IDOC) at Vandenberg Air Force Base Environmental Assessment

DTIC Science & Technology

2003-08-28

Zielinski , EDAW, Inc., concerning utilities supply and demand for Vandenberg Air Force Base, 1 August. Rush, P., 2002. Personal communication between...Pernell W. Rush, Technical Sergeant, Water Utilities/Water Treatment NCO, USAF 30th CES/CEOIU, Vandenberg Air Force Base, and James E. Zielinski ... Dave Savinsky, Environmental Consultant, 30 CES/CEVC, Vandenberg Air Force Base, on the Preliminary Draft Ground-Based Midcourse Defense (GMD

F-4 Beryllium Rudders; A Precis of the Design, Fabrication, Ground and Flight Test Demonstrations

DTIC Science & Technology

1975-05-01

Wright-Patterson Air Force Base , Ohio 45433. AIR FORCE FLIGHT DYNAMICS LABORATORY AIR FORCE SYSTEMS COMMAND WRIGHT-PATTERSON AIR FORCE BASE , OHIO 45433...rudder. These sequential ground tests include: - A 50,000 cycle fatigue test of upper balance weight support structure. A static test to...Design Details 6. Design Analysis 7. Rudder Mass Balance 8, Rudder Moment of Inertia 9, Rudder Weight RUDDER FABRICATION AND ASSEMBLY 1. 2

Air Force Audit Agency Management Information System

DTIC Science & Technology

1990-11-01

Support Directorate. AFAA/QL performs multilocation . Air Force-wide audits and issues reports to the SAF. It, however, specializes in the multibillion...USE ONLY (Leave blank) 2. REPORT DATE 3. REPORT TYPE AND DATES COVERED NOV 90 4. TITLE AND SUBTITLE S. FUNDING NUMBERS Air Force Audit Agency...appreciated. Mail them to: CADRE/RI, Building 1400, Maxwell AFB AL 36112-5532.• Air Force Audit Agency Management Hobbs Information System C 0* 0 0