Science.gov

Sample records for air-fuel mixture supplied

  1. Air/fuel supply system for use in a gas turbine engine

    DOEpatents

    Fox, Timothy A; Schilp, Reinhard; Gambacorta, Domenico

    2014-06-17

    A fuel injector for use in a gas turbine engine combustor assembly. The fuel injector includes a main body and a fuel supply structure. The main body has an inlet end and an outlet end and defines a longitudinal axis extending between the outlet and inlet ends. The main body comprises a plurality of air/fuel passages extending therethrough, each air/fuel passage including an inlet that receives air from a source of air and an outlet. The fuel supply structure communicates with and supplies fuel to the air/fuel passages for providing an air/fuel mixture within each air/fuel passage. The air/fuel mixtures exit the main body through respective air/fuel passage outlets.

  2. The impact of air-fuel mixture composition on SI engine performance during natural gas and producer gas combustion

    NASA Astrophysics Data System (ADS)

    Przybyła, G.; Postrzednik, S.; Żmudka, Z.

    2016-09-01

    The paper summarizers results of experimental tests of SI engine fuelled with gaseous fuels such as, natural gas and three mixtures of producer gas substitute that simulated real producer gas composition. The engine was operated under full open throttle and charged with different air-fuel mixture composition (changed value of air excess ratio). The spark timing was adjusted to obtain maximum brake torque (MBT) for each fuel and air-fuel mixture. This paper reports engine indicated performance based on in-cylinder, cycle resolved pressure measurements. The engine performance utilizing producer gas in terms of indicated efficiency is increased by about 2 percentage points when compared to fuelling with natural gas. The engine power de-rating when producer gas is utilized instead the natural gas, varies from 24% to 28,6% under stoichiometric combustion conditions. For lean burn (λ=1.5) the difference are lower and varies from 22% to 24.5%.

  3. Air/fuel ratio controller

    SciTech Connect

    Schechter, M.M.; Simko, A.O.

    1980-12-23

    An internal combustion engine has a fuel injection pump and an air/fuel ratio controller. The controller has a lever that is connected to the pump lever. An aneroid moves the controller lever as a function of changes in intake manifold vacuum to maintain a constant air/fuel ratio to the mixture charge. A fuel enrichment linkage is provided that modifies the movement of the fuel flow control lever by the aneroid in response to changes in manifold gas temperature levels and exhaust gas recirculation to maintain the constant air/fuel ratio. A manual override is provided to obtain a richer air/fuel ratio for maximum acceleration.

  4. Ignition and Supersonic Burning of Air - Fuel Mixtures Initiated by Electrical Discharges

    DTIC Science & Technology

    2005-08-04

    second order accuracy is used. On every time step the flowfield parameters are computed due Gauss - Seidel line relaxation numerical technique. inv GF...flame plasma is undertaken by the spectroscopy methods in the first section of the combustor (directly behind the step) and in the diagnostic chamber...bottom wall, 8 – fuel supply into the flame holder zones 1.3. Diagnostic complex. Main experimental methods of plasma discharges

  5. Treatment of synthetic arsenate wastewater with iron-air fuel cell electrocoagulation to supply drinking water and electricity in remote areas.

    PubMed

    Kim, Jung Hwan; Maitlo, Hubdar Ali; Park, Joo Yang

    2017-05-15

    Electrocoagulation with an iron-air fuel cell is an innovative arsenate removal system that can operate without an external electricity supply. Thus, this technology is advantageous for treating wastewater in remote regions where it is difficult to supply electricity. In this study, the possibility of real applications of this system for arsenate treatment with electricity production was verified through electrolyte effect investigations using a small-scale fuel cell and performance testing of a liter-scale fuel cell stack. The electrolyte species studied were NaCl, Na2SO4, and NaHCO3. NaCl was overall the most effective electrolyte for arsenate treatment, although Na2SO4 produced the greatest electrical current and power density. In addition, although the current density and power density were proportional to the concentrations of NaCl and Na2SO4, the use of concentrations above 20 mM of NaCl and Na2SO4 inhibited arsenate treatment due to competition effects between anions and arsenate in adsorption onto the iron hydroxide. The dominant iron hydroxide produced at the iron anode was found to be lepidocrocite by means of Raman spectroscopy. A liter-scale four-stack iron-air fuel cell with 10 mM NaCl electrolyte was found to be able to treat about 300 L of 1 ppm arsenate solution to below 10 ppb during 1 day, based on its 60-min treatment capacity, as well as produce the maximum power density of 250 mW/m(2).

  6. A review on air cathodes for zinc-air fuel cells

    NASA Astrophysics Data System (ADS)

    Neburchilov, Vladimir; Wang, Haijiang; Martin, Jonathan J.; Qu, Wei

    This paper reviews the compositions, design and methods of fabrication of air cathodes for alkali zinc-air fuel cells (ZAFCs), one of the few successfully commercialized fuel cells. The more promising compositions for air cathodes are based on individual oxides, or mixtures of such, with a spinel, perovskite, or pyrochlore structure: MnO 2, Ag, Co 3O 4, La 2O 3, LaNiO 3, NiCo 2O 4, LaMnO 3, LaNiO 3, etc. These compositions provide the optimal balance of ORR activity and chemical stability in an alkali electrolyte. The sol-gel and reverse micelle methods supply the most uniform distribution of the catalyst on carbon and the highest catalyst BET surface area. It is shown that the design of the air cathode, including types of carbon black, binding agents, current collectors, Teflon membranes, thermal treatment of the GDL, and catalyst layers, has a strong effect on performance.

  7. Performance Analysis of Joule-Thomson Cooler Supplied with Gas Mixtures

    NASA Astrophysics Data System (ADS)

    Piotrowska, A.; Chorowski, M.; Dorosz, P.

    2017-02-01

    Joule-Thomson (J-T) cryo-coolers working in closed cycles and supplied with gas mixtures are the subject of intensive research in different laboratories. The replacement of pure nitrogen by nitrogen-hydrocarbon mixtures allows to improve both thermodynamic parameters and economy of the refrigerators. It is possible to avoid high pressures in the heat exchanger and to use standard refrigeration compressor instead of gas bottles or high-pressure oil free compressor. Closed cycle and mixture filled Joule-Thomson cryogenic refrigerator providing 10-20 W of cooling power at temperature range 90-100 K has been designed and manufactured. Thermodynamic analysis including the optimization of the cryo-cooler mixture has been performed with ASPEN HYSYS software. The paper describes the design of the cryo-cooler and provides thermodynamic analysis of the system. The test results are presented and discussed.

  8. Cold start fuel/air mixture supply device for spark ignition internal combustion engines

    SciTech Connect

    Ross, G.E.D.

    1984-06-05

    A combined accelerator pump and cold start fuel/air mixture supply device has an automatic throttle valve in a mixture supply passage, a fuel control valve controlling flow of fuel drawn into the passage through an inlet upstream of the throttle valve, and an air valve upstream of the fuel inlet. A primary spring tends to seat the air valve. A light, secondary spring urges a plunger against the air valve to augment the load of the primary spring for a predetermined time interval after the engine begins to run under its own power. A valve in a pipe opens automatically at the end of the predetermined time interval to apply engine inlet manifold depression to the end of the plunger remote from the air valve and thereby to separate the plunger from the air valve so that only the primary spring acts on the air valve.

  9. Chemical evaluation of nutrient supply from fly ash-biosolids mixtures

    SciTech Connect

    Schumann, A.W.; Sumner, M.E.

    2000-02-01

    Prediction of plant nutrient supply from fly ash and biosolids (sewage sludge and poultry manure) may enhance their agricultural use as crop fertilizer. Two mild extraction methods (42-d equilibration with ion-exchange resins; 2-d equilibration with pH 4.8 buffered nutrient solution) and analysis of nutrient data by the Diagnosis and Recommendation Integrated System (DRIS) were tested with 29 fly ash samples, four biosolids samples, and their mixtures. The resin method was useful for major nutrient (N, P, K, Ca, Mg, S) extraction from fly ashes and organic materials, particularly where mineralizable fractions of N and P under aerobic conditions are required. However, resins were inefficient in extracting P from high-Fe sewage sludges because organic waste samples caused premature failure of semipermeable membranes and fouling of resins. Extraction of fly ash with dilute buffered nutrient solution was more successful because micronutrient recovery was improved, major nutrients were correlated to the resin method, both addition and removal of nutrients were recorded. DRIS analysis was possible, and equilibration was rapid (2 d). The overall nutrient supply from these extremely variable fly ashes was: Cu = Fe {approx} B {approx} Mo > Ca > S > Zn >> Mn > N > Mg > P > K (high micronutrient, low major nutrient supply). For biosolids, the major nutrients ranked: P > N {approx} Ca > S > Mg > K (sewage sludges), and N > Ca {approx} K > P > Mg > S (poultry manures). In mixtures of fly ash with 26% sewage sludge the order was: Ca > S > N > Mg > P > K, while in mixtures of fly ash and 13% poultry manure, the nutrients ranked: Ca > K {approx} N {approx} S > Mg > P. Optimal plant nutrition (especially N-P-K balancing) should be possible by mixing these three waste materials.

  10. High performance zinc air fuel cell stack

    NASA Astrophysics Data System (ADS)

    Pei, Pucheng; Ma, Ze; Wang, Keliang; Wang, Xizhong; Song, Mancun; Xu, Huachi

    2014-03-01

    A zinc air fuel cell (ZAFC) stack with inexpensive manganese dioxide (MnO2) as the catalyst is designed, in which the circulation flowing potassium hydroxide (KOH) electrolyte carries the reaction product away and acts as a coolant. Experiments are carried out to investigate the characteristics of polarization, constant current discharge and dynamic response, as well as the factors affecting the performance and uniformity of individual cells in the stack. The results reveal that the peak power density can be as high as 435 mW cm-2 according to the area of the air cathode sheet, and the influence factors on cell performance and uniformity are cell locations, filled state of zinc pellets, contact resistance, flow rates of electrolyte and air. It is also shown that the time needed for voltages to reach steady state and that for current step-up or current step-down are both in milliseconds, indicating the ZAFC can be excellently applied to vehicles with rapid dynamic response demands.

  11. Fuel Cell Electrodes for Hydrogen-Air Fuel Cell Assemblies.

    DTIC Science & Technology

    The report describes the design and evaluation of a hydrogen-air fuel cell module for use in a portable hydrid fuel cell -battery system. The fuel ... cell module consists of a stack of 20 single assemblies. Each assembly contains 2 electrically independent cells with a common electrolyte compartment

  12. Mixture Distributions for Modeling Lead Time Demand in Coordinated Supply Chains

    DTIC Science & Technology

    2014-05-01

    Finding Optimal Policies • Supplier would like to operate in a centralized supply chain → Define: TCc (Q,R,N) = TCb(Q,R,0)+ TCs(Q,N,0) (Q∗c, R∗c,N∗c...ArgMin (Q,R,N) TCc (Q,R,N) → Solution: Q∗c = 909, R∗c = 1004, N∗c = 1 → TCcb = 4955.9, TCcs = 1649.9, TCc = 6605.8 → Coordination can save: TC...TCd− TCc = 7704.4−6605.8 = 1098.5 24 Observations • Buyer prefers a decentralized supply chain: TCdb < TCcb • Supplier prefers a centralized supply

  13. Evaluation of Breathing Mixtures to be Used during Decompression for Mixed Gas Surface Supplied Dives,

    DTIC Science & Technology

    1982-01-31

    to provide for more than the most limited areas of application in terms of depth and exposure time. Further, experimental tests using modern methods...absolute.. The low oxygen percentage was necessary to provide a mixture which, with hydrogen was non-explosive and non- flamable . Since this mixture would...total of 47.2 + 4.6 = 51.8, well below the required limit . This produces a savings of 40% or 35 minutes which would appear to be a substantial benefit

  14. Effect of the air-fuel mixing on the NOx yield in a low-emission gas-turbine plant combustor

    NASA Astrophysics Data System (ADS)

    Vasil'ev, V. D.; Bulysova, L. A.; Berne, A. L.

    2016-04-01

    The article deals with construction of a simplified model of inhibition of nitric oxides formed in the combustors of the gas-turbine plants (GTPs) operating on natural gas. A combustor in which premixed, lean air-fuel mixtures are burnt is studied theoretically and experimentally. The research was carried out using a full-scale combustor that had parameters characteristic of modern GTPs. The article presents the results computed by the FlowVision software and the results of the experiments carried out on the test bench of the All-Russia Thermal Engineering Institute. The calculations and the tests were conducted under the following conditions: a flow rate of approximately 4.6 kg/s, a pressure to 450 kPa, an air temperature at the combustor inlet of approximately 400°C, the outlet temperature t 3 ≤ 1200°C, and natural gas as the fuel. The comparison of the simulated parameters with the experimental results underlies the constructed correlation dependence of the experimental NO x emission on the calculated parameter of nonuniform fuel concentration at the premixing zone outlet. The postulate about a weak dependence of the emission of NO x formed upon combustion of a perfectly mixed air-fuel mixture—when the methane concentration in air is constant at any point of the air-fuel mixture, i.e., constant in the mixture bulk—on the pressure in the combustor has been experimentally proven. The correctness and the practicability of the stationary mathematical model of the mixing process used to assess the NO x emission by the calculated amount of the air-fuel mixture generated in the premixing zone has been validated. This eliminates some difficulties that arise in the course of calculation of combustion and formation of NO x .

  15. Air/fuel ratio visualization in a diesel spray

    NASA Astrophysics Data System (ADS)

    Carabell, Kevin David

    1993-01-01

    To investigate some features of high pressure diesel spray ignition, we have applied a newly developed planar imaging system to a spray in an engine-fed combustion bomb. The bomb is designed to give flow characteristics similar to those in a direct injection diesel engine yet provide nearly unlimited optical access. A high pressure electronic unit injector system with on-line manually adjustable main and pilot injection features was used. The primary scalar of interest was the local air/fuel ratio, particularly near the spray plumes. To make this measurement quantitative, we have developed a calibration LIF technique. The development of this technique is the key contribution of this dissertation. The air/fuel ratio measurement was made using biacetyl as a seed in the air inlet to the engine. When probed by a tripled Nd:YAG laser the biacetyl fluoresces, with a signal proportional to the local biacetyl concentration. This feature of biacetyl enables the fluorescent signal to be used as as indicator of local fuel vapor concentration. The biacetyl partial pressure was carefully controlled, enabling estimates of the local concentration of air and the approximate local stoichiometry in the fuel spray. The results indicate that the image quality generated with this method is sufficient for generating air/fuel ratio contours. The processes during the ignition delay have a marked effect on ignition and the subsequent burn. These processes, vaporization and pre-flame kinetics, very much depend on the mixing of the air and fuel. This study has shown that poor mixing and over-mixing of the air and fuel will directly affect the type of ignition. An optimal mixing arrangement exists and depends on the swirl ratio in the engine, the number of holes in the fuel injector and the distribution of fuel into a pilot and main injection. If a short delay and a diffusion burn is desired, the best mixing parameters among those surveyed would be a high swirl ratio, a 4-hole nozzle and a

  16. Performance of an internal reforming molten carbonate fuel cell supplied with ethanol/water mixture

    SciTech Connect

    Freni, S.; Maggio, G.; Barone, F.

    1996-12-31

    The state of an on the field of molten carbonate fuel cell (MCFC) systems covers many technological aspects related to the use of these systems for the production of electricity. In this respect, extensive research efforts have been made to develop a technology using the methane based on the steam reforming process, and different configurations have been analyzed and their performance determined for several operative cell conditions. However, the operative temperature (T-923 K) of the MCFC. that allows the direct conversion of hydrocarbons or alcohols into H{sub 2} and CO, promotes researches in the field of alternative fuels, more easily transported and reformed compared to methane. In this paper are described the most indicative results obtained by a study that considers the use of water/ethanol mixture as an attractive alternative to the methane for a molten carbonate fuel cell.

  17. Zinc/air fuel cell for electric vehicles

    SciTech Connect

    Cherepy, N. J.; Krueger, R.; Cooper, J. F.

    1999-01-01

    We are conducting tests of an advanced zinc/air fuel cell design to determine effectiveness in various commercial applications. Our 322-cm2 cell uses gravity-fed zinc pellets as the anode, 12 M KOH electrolyte, and an air cathode catalyzed by a cobalt-porphyrin complex on carbon black. A single 322 cm2 cell runs at a standard operating power of 38 W (1200 W/m2) at 39 A (1245 A/m2) and 0.96 V with a power density of 2400 W/m2 at 0.67 V. With improved current collection hardware, already demonstrated in the laboratory, power generation increases to -3600 W/m2 at 1V. We conducted a 50-hour test in which a cell generated 587 Ah and 569 Wh. The power that may be generated increases by a factor of 2.5 between T = 28 °C and 52 °C. Electrolyte capacity, without stabilization additives, was measured at 147 Ah/L

  18. Flatness-based embedded control of air-fuel ratio in combustion engines

    NASA Astrophysics Data System (ADS)

    Rigatos, Gerasimos; Siano, Pierluigi; Arsie, Ivan

    2014-10-01

    A nonlinear controller is designed for air-fuel ratio control in combustion engines, making use of differential flatness theory and of the Derivative-free nonlinear Kalman Filter. It is proven that the air-fuel ratio system is a differentially flat one and admits dynamic feedback linearization. Using a change of variables that is based on differential flatness theory it is shown that the air-fuel ratio system can be transformed to the linear canonical form, for which the design of a state feedback controller is easier. Moreover, to compensate for modeling uncertainties and external disturbances the Derivative-free nonlinear Kalman Filter is designed as a disturbance observer. The estimation of the perturbations that effect the air-fuel systems enables their compensation through the inclusion of an additional term in the feedback control law. The efficiency of the proposed nonlinear feedback control scheme is tested through simulation experiments.

  19. Apparatus for controlling the air fuel mixture of an internal combustion engine

    SciTech Connect

    Harada, H.; Kimata, K.; Nakazeki, T.

    1980-06-03

    A fuel feeding apparatus for internal combustion engines comprises an area type air flow rate measuring section in which the air flow rate is dependent on the displacement of an air flow rate detecting valve, and a fuel flow rate measuring and distributing section in which a variable orifice defined by a rotor and a stator determines the fuel flow rate proportional to the air flow rate. This apparatus is characterized by the provision of an exhaust gas sensor disposed in the exhaust pipe for the detection of the oxygen concentration of the exhaust gas in order to achieve the complete combustion of fuel in the internal combustion engine, the output signal from the exhaust gas sensor being used to compensate the fuel feeding pressure and a spring force which acts on the pressure difference setting diaphragm of a servo-mechanism.

  20. A passive microfluidic hydrogen-air fuel cell with exceptional stability and high performance.

    PubMed

    Mitrovski, Svetlana M; Nuzzo, Ralph G

    2006-03-01

    We describe an advanced microfluidic hydrogen-air fuel cell (FC) that exhibits exceptional durability and high performance, most notably yielding stable output power (>100 days) without the use of an anode-cathode separator membrane. This FC embraces an entirely passive device architecture and, unlike conventional microfluidic designs that exploit laminar hydrodynamics, no external pumps are used to sustain or localize the reagent flow fields. The devices incorporate high surface area/porous metal and metal alloy electrodes that are embedded and fully immersed in liquid electrolyte confined in the channels of a poly(dimethylsiloxane) (PDMS)-based microfluidic network. The polymeric network also serves as a self-supporting membrane through which oxygen and hydrogen are supplied to the cathode and alloy anode, respectively, by permeation. The operational stability of the device and its performance is strongly dependent on the nature of the electrolyte used (5 M H2SO4 or 2.5 M NaOH) and composition of the anode material. The latter choice is optimized to decrease the sensitivity of the system to oxygen cross-over while still maintaining high activity towards the hydrogen oxidation reaction (HOR). Three types of high surface area anodes were tested in this work. These include: high-surface area electrodeposited Pt (Pt); high-surface area electrodeposited Pd (Pd); and thin palladium adlayers supported on a "porous" Pt electrode (Pd/Pt). The FCs display their best performance in 5 M H2SO4 using the Pd/Pt anode. This exceptional stability and performance was ascribed to several factors, namely: the high permeabilities of O2, H2, and CO2 in PDMS; the inhibition of the formation of insoluble carbonate species due to the presence of a highly acidic electrolyte; and the selectivity of the Pd/Pt anode toward the HOR. The stability of the device for long-term operation was modeled using a stack of three FCs as a power supply for a portable display that otherwise uses a 3 V

  1. Relationship between composition of mixture charged and that in circulation in an auto refrigerant cascade and a J-T refrigerator operating in liquid refrigerant supply mode

    NASA Astrophysics Data System (ADS)

    Sreenivas, Bura; Nayak, H. Gurudath; Venkatarathnam, G.

    2017-01-01

    The composition of the refrigerant mixture in circulation during steady state operation of J-T and allied refrigerators is not the same as that charged due to liquid hold up in the heat exchangers and phase separators, as well as the differential solubility of different refrigerant components in the compressor lubricating oil. The performance of refrigerators/liquefiers operating on mixed refrigerant cycles is dependent on the mixture composition. It is therefore important to charge the right mixture that results in an optimum composition in circulation during steady state operation. The relationship between the charged and circulating composition has been experimentally studied in a J-T refrigerator operating in the liquid refrigerant supply (LRS) mode and an auto refrigerant cascade refrigerator (with a phase separator) operating in the gas refrigerant supply (GRS) mode. The results of the study are presented in this work. The results show that the method presented earlier for J-T refrigerators operating in GRS mode is also applicable in the case of refrigerators studied in this work.

  2. In vitro ruminal fermentation characteristics and utilisable CP supply of sainfoin and birdsfoot trefoil silages and their mixtures with other legumes.

    PubMed

    Grosse Brinkhaus, A; Wyss, U; Arrigo, Y; Girard, M; Bee, G; Zeitz, J O; Kreuzer, M; Dohme-Meier, F

    2017-04-01

    The extensive protein degradation occurring during ensiling decreases the nutritive value of silages, but this might be counteracted by tannins. Therefore, silages from two legume species containing condensed tannins (CT) - sainfoin (SF) and birdsfoot trefoil (two cultivars: birdsfoot trefoil, cv. Bull (BTB) and birdsfoot trefoil, cv. Polom) - were compared for their in vitro ruminal fermentation characteristics. The effect of combining them with two CT-free legume silages (lucerne (LU) and red clover (RC)) was also determined. The supply of duodenally utilisable CP (uCP) in the forages was emphasised. The legumes were each harvested from three field sites. After 24 h of wilting on the field, the legumes were ensiled in laboratory silos for 86 days. Proximate constituents, silage fermentation characteristics, CT content and CP fractions were determined. Subsequently, silage samples and 1 : 1 mixtures of the CT-containing and CT-free silages were incubated for 24 h in batch cultures using ruminal fluid and buffer (1 : 2, v/v). Each treatment was replicated six times in six runs. The effects on pH, ammonia and volatile fatty acid concentrations, protozoal counts, and total gas and methane production were determined. uCP content was calculated by considering the CP in the silage and the ammonia in the incubation fluid from treatments and blanks. Statistical evaluation compared data from single plants alone and together with that from the mixtures. Among treatments, SF silage contained the least CP and the most CT. The non-protein nitrogen content was lower, favouring neutral detergent soluble and insoluble protein fractions, in the SF and RC silages. Absolute uCP content was lowest in SF and SF mixtures, although the ratio to total CP was the highest. In comparison with LU, the ammonia concentration of the incubation fluid was lower for SF, RC and BTB and for the mixture of SF with LU. The total gas and methane production was similar among the treatments, and the

  3. Assessment of methanol electro-oxidation for direct methanol-air fuel cells

    SciTech Connect

    Fritts, S.D.; Sen, R.K.

    1988-07-01

    The Office of Energy Storage and Distribution of the US Department of Energy (DOE) supports the development of a methanol-air fuel cell for transportation application. The approach used at Los Alamos National Laboratory converts the methanol fuel to a hydrogen-rich gas in a reformer, then operates the fuel cell on hydrogen and air. The reformer tends to be bulky (raising vehicle packaging problems), has a long startup period, and is not well suited for the transient operation required in a vehicle. Methanol, however, can be oxidized electrochemically in the fuel cell. If this process can be conducted efficiently, a direct methanol-air fuel cell can be used, which does not require a reformer. The objective of this study is to assess the potential of developing a suitable catalyst for the direct electrochemical oxidation of methanol. The primary conclusion of this study is that no acceptable catalysts exist can efficiently oxidize methanol electrochemically and have the desired cost and lifetime for vehicle applications. However, recent progress in understanding the mechanism of methanol oxidation indicates that a predictive base can be developed to search for methanol oxidation catalysts and can be used to methodically develop improved catalysts. Such an approach is strongly recommended. The study also recommends that until further progress in developing high-performance catalysts is achieved, research in cell design and testing is not warranted. 43 refs., 12 figs., 1 tab.

  4. Performance of PEM Liquid-Feed Direct Methanol-Air Fuel Cells

    NASA Technical Reports Server (NTRS)

    Narayanan, S. R.

    1995-01-01

    A direct methanol-air fuel cell operating at near atmospheric pressure, low-flow rate air, and at temperatures close to 60oC would tremendously enlarge the scope of potential applications. While earlier studies have reported performance with oxygen, the present study focuses on characterizing the performance of a PEM liquid feed direct methanol-air cell consisting of components developed in house. These cells employ Pt-Ru catalyst in the anode, Pt at the cathode and Nafion 117 as the PEM. The effect of pressure, flow rate of air and temperature on cell performance has been studied. With air, the performance level is as high as 0.437 V at 300 mA/cm2 (90oC, 20 psig, and excess air flow) has been attained. Even more significant is the performance level at 60oC, 1 atm and low flow rates of air (3-5 times stoichiometric), which is 0.4 V at 150 mA/cm2. Individual electrode potentials for the methanol and air electrode have been separated and analyzed. Fuel crossover rates and the impact of fuel crossover on the performance of the air electrode have also been measured. The study identifies issues specific to the methanol-air fuel cell and provides a basis for improvement strategies.

  5. Morphology control of zinc regeneration for zinc-air fuel cell and battery

    NASA Astrophysics Data System (ADS)

    Wang, Keliang; Pei, Pucheng; Ma, Ze; Xu, Huachi; Li, Pengcheng; Wang, Xizhong

    2014-12-01

    Morphology control is crucial both for zinc-air batteries and for zinc-air fuel cells during zinc regeneration. Zinc dendrite should be avoided in zinc-air batteries and zinc pellets are yearned to be formed for zinc-air fuel cells. This paper is mainly to analyze the mechanism of shape change and to control the zinc morphology during charge. A numerical three-dimensional model for zinc regeneration is established with COMSOL software on the basis of ionic transport theory and electrode reaction electrochemistry, and some experiments of zinc regeneration are carried out. The deposition process is qualitatively analyzed by the kinetics Monte Carlo method to study the morphological change from the electrocrystallization point of view. Morphological evolution of deposited zinc under different conditions of direct currents and pulse currents is also investigated by simulation. The simulation shows that parametric variables of the flowing electrolyte, the surface roughness and the structure of the electrode, the charging current and mode affect morphological evolution. The uniform morphology of deposited zinc is attained at low current, pulsating current or hydrodynamic electrolyte, and granular morphology is obtained by means of an electrode of discrete columnar structure in combination with high current and flowing electrolyte.

  6. Effect of Volatility on Air-Fuel Ratio Distribution and Torque Output of a Carbureted Light Aircraft Piston Engine.

    DTIC Science & Technology

    1982-03-01

    Positive displacement fuel flow sensor Burette type volumetric fuel flowmeter(2) Meriam laminar airflow meter Lamdascan air-fuel ratio meter Lebow inline...therefore the resulting data was not utilized. The volumetric flowrate of engine intake air was calculated from the pressure drop across a Meriam Model 50MC2

  7. Determining the Maximum Cumulative Ratios for Mixtures Observed in Ground Water Wells Used as Drinking Water Supplies in the United States

    PubMed Central

    Han, Xianglu; Price, Paul S.

    2011-01-01

    The maximum cumulative ratio (MCR) developed in previous work is a tool to evaluate the need to perform cumulative risk assessments. MCR is the ratio of the cumulative exposures to multiple chemicals to the maximum exposure from one of the chemicals when exposures are described using a common metric. This tool is used to evaluate mixtures of chemicals measured in samples of untreated ground water as source for drinking water systems in the United States. The mixtures of chemicals in this dataset differ from those examined in our previous work both in terms of the predicted toxicity and compounds measured. Despite these differences, MCR values in this study follow patterns similar to those seen earlier. MCR values for the mixtures have a mean (range) of 2.2 (1.03–5.4) that is much smaller than the mean (range) of 16 (5–34) in the mixtures in previous study. The MCR values of the mixtures decline as Hazard Index (HI) values increase. MCR values for mixtures with larger HI values are not affected by possible contributions from chemicals that may occur at levels below the detection limits. This work provides a second example of use of the MCR tool in the evaluation of mixtures that occur in the environment. PMID:22408599

  8. Determining the maximum cumulative ratios for mixtures observed in ground water wells used as drinking water supplies in the United States.

    PubMed

    Han, Xianglu; Price, Paul S

    2011-12-01

    The maximum cumulative ratio (MCR) developed in previous work is a tool to evaluate the need to perform cumulative risk assessments. MCR is the ratio of the cumulative exposures to multiple chemicals to the maximum exposure from one of the chemicals when exposures are described using a common metric. This tool is used to evaluate mixtures of chemicals measured in samples of untreated ground water as source for drinking water systems in the United States. The mixtures of chemicals in this dataset differ from those examined in our previous work both in terms of the predicted toxicity and compounds measured. Despite these differences, MCR values in this study follow patterns similar to those seen earlier. MCR values for the mixtures have a mean (range) of 2.2 (1.03-5.4) that is much smaller than the mean (range) of 16 (5-34) in the mixtures in previous study. The MCR values of the mixtures decline as Hazard Index (HI) values increase. MCR values for mixtures with larger HI values are not affected by possible contributions from chemicals that may occur at levels below the detection limits. This work provides a second example of use of the MCR tool in the evaluation of mixtures that occur in the environment.

  9. In situ STM studies of zinc in aqueous solutions containing PEG DiAcid inhibitor: Correlation with electrochemical performances of zinc-air fuel cells

    NASA Astrophysics Data System (ADS)

    Cohen-Hyams, Tzipi; Ziengerman, Yuli; Ein-Eli, Yair

    Electrochemical performance of prismatic zinc-air fuel cells comprising zinc anode gel containing poly(ethylene glycol) (PEG 600) and poly(ethylene glycol) bis(carboxymethyl) ether (PEG DiAcid 600) as corrosion inhibitor were studied. It was found that in addition to the low zinc corrosion rates obtained from cells utilizing PEG DiAcid 600 as corrosion inhibitor, both analog and global mobile system (GSM) discharge capacities and potential plateaus, in a wide range of temperatures were higher once PEG DiAcid was added to the zinc gel mixtures. The results obtained from in situ scanning tunneling microscopy (STM) studies of zinc substrates immersed in deionized (DI) water containing inhibitors reveal that the film produced on the zinc metal in the presence of PEG DiAcid is by far thinner than the film produced by other inhibitors such as PEG 600 and polyoxyethylene alkyl phosphate ester acid (GAFAC RA 600). These studies also reveal that the addition of PEG DiAcid forms an adherent and a complete protective coverage, while the addition of PEG 600 and GAFAC RA 600 resulted in an incomplete coverage with the appearance of pits and terraces, indicating on a restricted inhibition performance of these two polymers compared with PEG DiAcid. These studies suggest a low interface resistivity of zinc immersed in alkaline solution containing PEG DiAcid, which is expressed in a higher working potential and increased cell capacity in different temperatures at two discharge modes of analog and GSM.

  10. Adaptive critic learning techniques for engine torque and air-fuel ratio control.

    PubMed

    Liu, Derong; Javaherian, Hossein; Kovalenko, Olesia; Huang, Ting

    2008-08-01

    A new approach for engine calibration and control is proposed. In this paper, we present our research results on the implementation of adaptive critic designs for self-learning control of automotive engines. A class of adaptive critic designs that can be classified as (model-free) action-dependent heuristic dynamic programming is used in this research project. The goals of the present learning control design for automotive engines include improved performance, reduced emissions, and maintained optimum performance under various operating conditions. Using the data from a test vehicle with a V8 engine, we developed a neural network model of the engine and neural network controllers based on the idea of approximate dynamic programming to achieve optimal control. We have developed and simulated self-learning neural network controllers for both engine torque (TRQ) and exhaust air-fuel ratio (AFR) control. The goal of TRQ control and AFR control is to track the commanded values. For both control problems, excellent neural network controller transient performance has been achieved.

  11. NanoCapillary Network Proton Conducting Membranes for High Temperature Hydrogen/Air Fuel Cells

    SciTech Connect

    Pintauro, Peter

    2012-07-09

    The objective of this proposal is to fabricate and characterize a new class of NanoCapillary Network (NCN) proton conducting membranes for hydrogen/air fuel cells that operate under high temperature, low humidity conditions. The membranes will be intelligently designed, where a high density interconnecting 3-D network of nm-diameter electrospun proton conducting polymer fibers is embedded in an inert (uncharged) water/gas impermeable polymer matrix. The high density of fibers in the resulting mat and the high ion-exchange capacity of the fiber polymer will ensure high proton conductivity. To further enhance water retention, molecular silica will be added to the sulfonated polymer fibers. The uncharged matrix material will control water swelling of the high ion-exchange capacity proton conducting polymer fibers and will impart toughness to the final nanocapillary composite membrane. Thus, unlike other fuel cell membranes, the role of the polymer support matrix will be decoupled from that of the proton-conducting channels. The expected final outcome of this 5-year project is the fabrication of fuel cell membranes with properties that exceed the DOE’s technical targets, in particular a proton conductivity of 0.1 S/cm at a temperature less than or equal to120°C and 25-50% relative humidity.

  12. Three-way conversion catalysts on vehicles fueled with ethanol-gasoline mixtures

    SciTech Connect

    Mooney, J.J.; Hansel, J.G.; Burns, K.R.

    1980-01-01

    Three-way conversion catalysts systems which provide control of three emission components - hydrocarbons, carbon monoxide, and oxides of nitrogen - generally require the use of closed-loop feedback control of the air/fuel metering system to provide a near stoichiometric exhaust gas composition. As an alternate fuel such as ethyl-alcohol is added to gasoline, the stoichiometric air/fuel ratio is altered. Conventional air/fuel metering systems do not compensate for this change. The ability of the Volvo closed-loop control fuel injection system, now in use on vehicles in the US, to maintain the stoichiometric air/fuel mixture needed for optimum emission control and to compensate for the change in fuel stoichiometry encountered in gasoline/alternate fuel mixtures is examined. The system was found to have the ability to completely compensate for gasoline/ethyl alcohol mixtures up to 30% ethyl alcohol with no loss in emission control. Gasoline/methyl alcohol blends were also tested successfully. There is definite potential for the three-way conversion catalyst/closed-loop systems to provide our nation with flexibility in fuel formulation not otherwise found in conventional fuel metering systems. With proper planning and engineering, nonpetroleum derived fuels can be blended with gasoline without requiring engine adjustments or compromising emission controls.

  13. A Rechargeable Li-Air Fuel Cell Battery Based on Garnet Solid Electrolytes.

    PubMed

    Sun, Jiyang; Zhao, Ning; Li, Yiqiu; Guo, Xiangxin; Feng, Xuefei; Liu, Xiaosong; Liu, Zhi; Cui, Guanglei; Zheng, Hao; Gu, Lin; Li, Hong

    2017-01-24

    Non-aqueous Li-air batteries have been intensively studied in the past few years for their theoretically super-high energy density. However, they cannot operate properly in real air because they contain highly unstable and volatile electrolytes. Here, we report the fabrication of solid-state Li-air batteries using garnet (i.e., Li6.4La3Zr1.4Ta0.6O12, LLZTO) ceramic disks with high density and ionic conductivity as the electrolytes and composite cathodes consisting of garnet powder, Li salts (LiTFSI) and active carbon. These batteries run in real air based on the formation and decomposition at least partially of Li2CO3. Batteries with LiTFSI mixed with polyimide (PI:LiTFSI) as a binder show rechargeability at 200 °C with a specific capacity of 2184 mAh g(-1)carbon at 20 μA cm(-2). Replacement of PI:LiTFSI with LiTFSI dissolved in polypropylene carbonate (PPC:LiTFSI) reduces interfacial resistance, and the resulting batteries show a greatly increased discharge capacity of approximately 20300 mAh g(-1)carbon and cycle 50 times while maintaining a cutoff capacity of 1000 mAh g(-1)carbon at 20 μA cm(-2) and 80 °C. These results demonstrate that the use of LLZTO ceramic electrolytes enables operation of the Li-air battery in real air at medium temperatures, leading to a novel type of Li-air fuel cell battery for energy storage.

  14. A Rechargeable Li-Air Fuel Cell Battery Based on Garnet Solid Electrolytes

    NASA Astrophysics Data System (ADS)

    Sun, Jiyang; Zhao, Ning; Li, Yiqiu; Guo, Xiangxin; Feng, Xuefei; Liu, Xiaosong; Liu, Zhi; Cui, Guanglei; Zheng, Hao; Gu, Lin; Li, Hong

    2017-01-01

    Non-aqueous Li-air batteries have been intensively studied in the past few years for their theoretically super-high energy density. However, they cannot operate properly in real air because they contain highly unstable and volatile electrolytes. Here, we report the fabrication of solid-state Li-air batteries using garnet (i.e., Li6.4La3Zr1.4Ta0.6O12, LLZTO) ceramic disks with high density and ionic conductivity as the electrolytes and composite cathodes consisting of garnet powder, Li salts (LiTFSI) and active carbon. These batteries run in real air based on the formation and decomposition at least partially of Li2CO3. Batteries with LiTFSI mixed with polyimide (PI:LiTFSI) as a binder show rechargeability at 200 °C with a specific capacity of 2184 mAh g‑1carbon at 20 μA cm‑2. Replacement of PI:LiTFSI with LiTFSI dissolved in polypropylene carbonate (PPC:LiTFSI) reduces interfacial resistance, and the resulting batteries show a greatly increased discharge capacity of approximately 20300 mAh g‑1carbon and cycle 50 times while maintaining a cutoff capacity of 1000 mAh g‑1carbon at 20 μA cm‑2 and 80 °C. These results demonstrate that the use of LLZTO ceramic electrolytes enables operation of the Li-air battery in real air at medium temperatures, leading to a novel type of Li-air fuel cell battery for energy storage.

  15. A Rechargeable Li-Air Fuel Cell Battery Based on Garnet Solid Electrolytes

    PubMed Central

    Sun, Jiyang; Zhao, Ning; Li, Yiqiu; Guo, Xiangxin; Feng, Xuefei; Liu, Xiaosong; Liu, Zhi; Cui, Guanglei; Zheng, Hao; Gu, Lin; Li, Hong

    2017-01-01

    Non-aqueous Li-air batteries have been intensively studied in the past few years for their theoretically super-high energy density. However, they cannot operate properly in real air because they contain highly unstable and volatile electrolytes. Here, we report the fabrication of solid-state Li-air batteries using garnet (i.e., Li6.4La3Zr1.4Ta0.6O12, LLZTO) ceramic disks with high density and ionic conductivity as the electrolytes and composite cathodes consisting of garnet powder, Li salts (LiTFSI) and active carbon. These batteries run in real air based on the formation and decomposition at least partially of Li2CO3. Batteries with LiTFSI mixed with polyimide (PI:LiTFSI) as a binder show rechargeability at 200 °C with a specific capacity of 2184 mAh g−1carbon at 20 μA cm−2. Replacement of PI:LiTFSI with LiTFSI dissolved in polypropylene carbonate (PPC:LiTFSI) reduces interfacial resistance, and the resulting batteries show a greatly increased discharge capacity of approximately 20300 mAh g−1carbon and cycle 50 times while maintaining a cutoff capacity of 1000 mAh g−1carbon at 20 μA cm−2 and 80 °C. These results demonstrate that the use of LLZTO ceramic electrolytes enables operation of the Li-air battery in real air at medium temperatures, leading to a novel type of Li-air fuel cell battery for energy storage. PMID:28117359

  16. The use of air fuel cell cathodes to remove contaminants from spent chromium plating solutions.

    PubMed

    Huang, K L; Holsen, T M; Chou, T C; Yang, M C

    2004-01-01

    Results from experiments using an impregnation-reduction (I-R) Pt / Nafion membrane electrode assembly (MEA) in an air fuel cell cathode to remove contaminants (Cu(II), Ni(II), and Fe(III)) from spent chromium electroplating baths are presented in this study. A platinum-carbon (Pt-C) / Nafion MEA and a Pb planar cathode were also used for comparison. The average removal rates of Cu(II) and Ni(II) were almost the same (0.39 and 0.40 mM hr(-1) (or 0.117 and 0.12 mmol hr(-1)), respectively) but higher than that of Fe(III) (0.16 mM hr(-1), or 0.048 mmol hr(-1)) in accordance with the Nernst-Planck flux equation. The removal rates for the same cation were independent of the cathode used. The average removal rate of each impurity was approximately proportional to the product of its initial concentration and separator area/anolyte volume ratio using Pb cathodes. Under constant current conditions the system using the Pt-C / Nafion cathode needed the highest cell voltage, about 3 V more than needed for the system with the Pt / Nafion cathode. The cell voltage required using the Pt / Nafion cathode was similar to that using the conventional planar Pb cathode. Analyses of cathode deposits by SEM/EDS and XPS techniques indicated they were minimal on the Pb and Pt / Nafion cathode and more apparent on the Pt-C / Nafion cathode. The primary deposits on the Pb cathode were chromium oxides (e.g., Cr2O3) with minor amount of lead chromate (lead dichromate or lead trichromate) and other chromium solids (Cr black). As expected, the dominant deposit on the lead anode surface was PbO2.

  17. Fuel supplying device for internal combustion engine

    SciTech Connect

    Ishida, T.; Miki, T.; Nakamura, H.; Takamiya, B.

    1982-07-13

    A fuel supplying device for an internal combustion engine is disclosed which has a fuel supply passage for introducing fuel fed from a fuel pump at a substantially constant pressure to a fuel injector operative at a predetermined constant pressure. The fuel injector is installed at a congregated portion of engine intake manifolds. A metering valve includes a motor so that the pressure drop is maintained substantially constant by a differential regulator. The metering valve is disposed in an intermediate portion of the fuel supply passage. Calculating means including a servo signal generator calculates an injection flow amount causing a predetermined air/fuel ratio on the basis of signals of various engine running factors. An operational signal output from the servo signal generating circuit of the calculating means is applied to the drive motor means for driving said metering valve to thereby inject fuel into the intake manifolds.

  18. PEM fuel cell cathode carbon corrosion due to the formation of air/fuel boundary at the anode

    NASA Astrophysics Data System (ADS)

    Tang, Hao; Qi, Zhigang; Ramani, Manikandan; Elter, John F.

    The impacts of unprotected start up and shut down on fuel cell performance degradation was investigated using both single cell and dual cell configurations. It was found that the air/fuel boundary developed at the anode side after a fuel cell shut down or during its restart caused extremely quick degradation of the cathode. The thickness, the electrochemical active surface area, and the performance of the cathode catalyst layer were significantly reduced. By using a dual cell configuration, cathode potential as high as two times of open circuit voltage was measured, and the corrosion current flowing externally between the two cells was detected and quantified. Carbon catalyst-support corrosion/oxidation at such a high potential was largely responsible for the accelerated fuel cell performance degradation.

  19. High-temperature sorbent method for removal of sulfur containing gases from gaseous mixtures

    DOEpatents

    Young, John E.; Jalan, Vinod M.

    1984-01-01

    A copper oxide-zinc oxide mixture is used as a sorbent for removing hydrogen sulfide and other sulfur containing gases at high temperatures from a gaseous fuel mixture. This high-temperature sorbent is especially useful for preparing fuel gases for high temperature fuel cells. The copper oxide is initially reduced in a preconditioning step to elemental copper and is present in a highly dispersed state throughout the zinc oxide which serves as a support as well as adding to the sulfur sorption capacity. The spent sorbent is regenerated by high-temperature treatment with an air fuel, air steam mixture followed by hydrogen reduction to remove and recover the sulfur.

  20. High-temperature sorbent method for removal of sulfur containing gases from gaseous mixtures

    DOEpatents

    Young, J.E.; Jalan, V.M.

    1984-06-19

    A copper oxide-zinc oxide mixture is used as a sorbent for removing hydrogen sulfide and other sulfur containing gases at high temperatures from a gaseous fuel mixture. This high-temperature sorbent is especially useful for preparing fuel gases for high temperature fuel cells. The copper oxide is initially reduced in a preconditioning step to elemental copper and is present in a highly dispersed state throughout the zinc oxide which serves as a support as well as adding to the sulfur sorption capacity. The spent sorbent is regenerated by high-temperature treatment with an air fuel, air steam mixture followed by hydrogen reduction to remove and recover the sulfur.

  1. High-temperature sorbent method for removal of sulfur-containing gases from gaseous mixtures

    DOEpatents

    Young, J.E.; Jalan, V.M.

    1982-07-07

    A copper oxide-zinc oxide mixture is used as a sorbent for removing hydrogen sulfide and other sulfur containing gases at high temperatures from a gaseous fuel mixture. This high-temperature sorbent is especially useful for preparing fuel gases for high temperature fuel cells. The copper oxide is initially reduced in a preconditioning step to elemental copper and is present in a highly dispersed state throughout the zinc oxide which serves as a support as well as adding to the sulfur sorbtion capacity. The spent sorbent is regenerated by high-temperature treatment with an air fuel, air steam mixture followed by hydrogen reduction to remove and recover the sulfur.

  2. Properties of Artificial Gaseous Mixtures for their Safe Use and Support the Natural Gas Supply Networks / Własności Sztucznych Mieszanin Gazowych do Bezpiecznego ich Użytkowania i Wspomagania Zasilania Sieci Gazu Ziemnego

    NASA Astrophysics Data System (ADS)

    Łaciak, Mariusz

    2012-11-01

    The increase in natural gas consumption by the general public and industry development, in particular the petrochemical and chemical industries, has made increasing the world interest in using gas replacement for natural gas, both as mixtures of flammable gases and gas mixtures as LPG with air (SNG - Synthetic Natural Gas). Economic analysis in many cases prove that to ensure interchangeability of gas would cost less than the increase in pipeline capacity to deliver the same quantity of natural gas. In addition, SNG systems and installations, could be considered as investments to improve security and flexibility of gas supply. Known existing methods for determining the interchangeability of gases in gas gear based on Wobbe index, which determines the heat input and the burning rate tide, which in turn is related to flame stability. Exceeding the Wobbe index of a value increases the amount of carbon monoxide in the exhaust than the permissible concentration. Methods of determining the interchangeability of gases is characterized by a gas in relation to the above-described phenomena by means of quantitative indicators, or using diagrams interchangeability, where the gas is characterized by the position of a point in a coordinate system. The best known method for determining the interchangeability of gases is Delbourg method, in which the gas is characterized by the revised (expanded) Wobbe Index (Wr), the combustion potential, rate of soot formation (Ic) and the ratio of the formation of yellow ends (I). Universal way to determine the interchangeability of gas is also Weaver accounting method. It does not require determination of the reference gas. It is designed for utensils for household gas and gas pressure p = 1.25 kPa. The criteria and definition of gas interchangeability volatility in practice to the combustion in a gas gear. In the case of gas exchange in industrial furnaces, interchangeability criteria are usually not very useful because of other conditions

  3. Mixture Experiments

    SciTech Connect

    Piepel, Gregory F.

    2007-12-01

    A mixture experiment involves combining two or more components in various proportions or amounts and then measuring one or more responses for the resulting end products. Other factors that affect the response(s), such as process variables and/or the total amount of the mixture, may also be studied in the experiment. A mixture experiment design specifies the combinations of mixture components and other experimental factors (if any) to be studied and the response variable(s) to be measured. Mixture experiment data analyses are then used to achieve the desired goals, which may include (i) understanding the effects of components and other factors on the response(s), (ii) identifying components and other factors with significant and nonsignificant effects on the response(s), (iii) developing models for predicting the response(s) as functions of the mixture components and any other factors, and (iv) developing end-products with desired values and uncertainties of the response(s). Given a mixture experiment problem, a practitioner must consider the possible approaches for designing the experiment and analyzing the data, and then select the approach best suited to the problem. Eight possible approaches include 1) component proportions, 2) mathematically independent variables, 3) slack variable, 4) mixture amount, 5) component amounts, 6) mixture process variable, 7) mixture of mixtures, and 8) multi-factor mixture. The article provides an overview of the mixture experiment designs, models, and data analyses for these approaches.

  4. Method and device for optimizing the air-fuel mixture burn rate of internal combustion engines during low speed, light and heavy load operating conditions

    SciTech Connect

    Burandt, C.O.

    1990-10-09

    This patent describes a method for optimizing low speed light load and low speed heavy load operating conditions in an internal combustion engine. The engine has a camshaft, a crankshaft, at least one intake valve and at least one piston, and is capable of providing for small valve events, and the engine providing for earlier than normal intake valve closings the method comprises: sensing the load demand on the engine, regulating the phasing of the operation of the camshaft of the engine with the operation of the crankshaft of the engine in response to the sensed load demand by advancing the operation of camshaft relative to the operation of the crankshaft when a heavy load demand is sensed and by retarding the operation of the camshaft relative to the operation of the crankshaft when alight load demand is sensed, and sensing detonation in the engine and regulating the phasing operation of the camshaft relative to the operation of the crankshaft by advancing the operation of the camshaft relative to the crankshaft when detonation is sensed.

  5. Strategic Supply

    DTIC Science & Technology

    2005-01-01

    the potential to capitalize on more efficient and effective management of their respective supply chains . Supply Chain Management (SCM) is the...transformation efforts have the potential to create a more agile, flexible and resilient supply chain that is responsive to Commanders and sensitive to...optimizing their supply chain to remain viable and create competitive advantage. Supply Chain Management (SCM) is grounded in the field of logistics

  6. Application of TiC reinforced Fe-based coatings by means of High Velocity Air Fuel Spraying

    NASA Astrophysics Data System (ADS)

    Bobzin, K.; Öte, M.; Knoch, M. A.; Liao, X.; Sommer, J.

    2017-03-01

    In the field of hydraulic applications, different development trends can cause problems for coatings currently used as wear and corrosion protection for piston rods. Aqueous hydraulic fluids and rising raw material prices necessitate the search for alternatives to conventional coatings like galvanic hard chrome or High Velocity Oxygen Fuel (HVOF)-sprayed WC/Co coatings. In a previous study, Fe/TiC coatings sprayed by a HVOF-process, were identified to be promising coating systems for wear and corrosion protection in hydraulic systems. In this feasibility study, the novel High Velocity Air Fuel (HVAF)-process, a modification of the HVOF-process, is investigated using the same feedstock material, which means the powder is not optimized for the HVAF-process. The asserted benefits of the HVAF-process are higher particle velocities and lower process temperatures, which can result in a lower porosity and oxidation of the coating. Further benefits of the HVAF process are claimed to be lower process costs and higher deposition rates. In this study, the focus is set on to the applicability of Fe/TiC coatings by HVAF in general. The Fe/TiC HVAF coating could be produced, successfully. The HVAF- and HVOF-coatings, produced with the same powder, were investigated using micro-hardness, porosity, wear and corrosion tests. A similar wear coefficient and micro-hardness for both processes could be achieved. Furthermore the propane/hydrogen proportion of the HVAF process and its influence on the coating thickness and the porosity was investigated.

  7. Strategic Supply

    DTIC Science & Technology

    2006-01-01

    context of Supply Chain Management ( SCM ), it is quite apparent that Strategic Supply cannot be classified as a particular industry; but rather, as an...Management ( SCM ), it is quite apparent that Strategic Supply cannot be classified as a particular industry; but rather, as an enabler across all...advantage in the global marketplace. The Council of Supply Chain Management Professionals (CSCMP) has defined SCM as, “…encompassing the planning

  8. Wavelength and energy dependent absorption of unconventional fuel mixtures

    NASA Astrophysics Data System (ADS)

    Khan, N.; Saleem, Z.; Mirza, A. A.

    2005-11-01

    Economic considerations of laser induced ignition over the normal electrical ignition of direct injected Compressed Natural Gas (CNG) engines has motivated automobile industry to go for extensive research on basic characteristics of leaner unconventional fuel mixtures to evaluate practical possibility of switching over to the emerging technologies. This paper briefly reviews the ongoing research activities on minimum ignition energy and power requirements of natural gas fuels and reports results of present laser air/CNG mixture absorption coefficient study. This study was arranged to determine the thermo-optical characteristics of high air/fuel ratio mixtures using laser techniques. We measured the absorption coefficient using four lasers of multiple wavelengths over a wide range of temperatures and pressures. The absorption coefficient of mixture was found to vary significantly over change of mixture temperature and probe laser wavelengths. The absorption coefficients of air/CNG mixtures were measured using 20 watts CW/pulsed CO2 laser at 10.6μm, Pulsed Nd:Yag laser at 1.06μm, 532 nm (2nd harmonic) and 4 mW CW HeNe laser at 645 nm and 580 nm for temperatures varying from 290 to 1000K using optical transmission loss technique.

  9. Performance evaluation of an advanced air-fuel ratio controller on a stationary, rich-burn natural gas engine

    NASA Astrophysics Data System (ADS)

    Kochuparampil, Roshan Joseph

    The advent of an era of abundant natural gas is making it an increasingly economical fuel source against incumbents such as crude oil and coal, in end-use sectors such as power generation, transportation and industrial chemical production, while also offering significant environmental benefits over these incumbents. Equipment manufacturers, in turn, are responding to widespread demand for power plants optimized for operation with natural gas. In several applications such as distributed power generation, gas transmission, and water pumping, stationary, spark-ignited, natural gas fueled internal combustion engines (ICEs) are the power plant of choice (over turbines) owing to their lower equipment and operational costs, higher thermal efficiencies across a wide load range, and the flexibility afforded to end-users when building fine-resolution horsepower topologies: modular size increments ranging from 100 kW -- 2 MW per ICE power plant compared to 2 -- 5 MW per turbine power plant. Under the U.S. Environment Protection Agency's (EPA) New Source Performance Standards (NSPS) and Reciprocating Internal Combustion Engine National Emission Standards for Hazardous Air Pollutants (RICE NESHAP) air quality regulations, these natural gas power plants are required to comply with stringent emission limits, with several states mandating even stricter emissions norms. In the case of rich-burn or stoichiometric natural gas ICEs, very high levels of sustained emissions reduction can be achieved through exhaust after-treatment that utilizes Non Selective Catalyst Reduction (NSCR) systems. The primary operational constraint with these systems is the tight air-fuel ratio (AFR) window of operation that needs to be maintained if the NSCR system is to achieve simultaneous reduction of carbon monoxide (CO), nitrogen oxides (NOx), total hydrocarbons (THC), volatile organic compounds (VOCs), and formaldehyde (CH 2O). Most commercially available AFR controllers utilizing lambda (oxygen

  10. Kinetic mechanism of molecular energy transfer and chemical reactions in low-temperature air-fuel plasmas.

    PubMed

    Adamovich, Igor V; Li, Ting; Lempert, Walter R

    2015-08-13

    This work describes the kinetic mechanism of coupled molecular energy transfer and chemical reactions in low-temperature air, H2-air and hydrocarbon-air plasmas sustained by nanosecond pulse discharges (single-pulse or repetitive pulse burst). The model incorporates electron impact processes, state-specific N(2) vibrational energy transfer, reactions of excited electronic species of N(2), O(2), N and O, and 'conventional' chemical reactions (Konnov mechanism). Effects of diffusion and conduction heat transfer, energy coupled to the cathode layer and gasdynamic compression/expansion are incorporated as quasi-zero-dimensional corrections. The model is exercised using a combination of freeware (Bolsig+) and commercial software (ChemKin-Pro). The model predictions are validated using time-resolved measurements of temperature and N(2) vibrational level populations in nanosecond pulse discharges in air in plane-to-plane and sphere-to-sphere geometry; temperature and OH number density after nanosecond pulse burst discharges in lean H(2)-air, CH(4)-air and C(2)H(4)-air mixtures; and temperature after the nanosecond pulse discharge burst during plasma-assisted ignition of lean H2-mixtures, showing good agreement with the data. The model predictions for OH number density in lean C(3)H(8)-air mixtures differ from the experimental results, over-predicting its absolute value and failing to predict transient OH rise and decay after the discharge burst. The agreement with the data for C(3)H(8)-air is improved considerably if a different conventional hydrocarbon chemistry reaction set (LLNL methane-n-butane flame mechanism) is used. The results of mechanism validation demonstrate its applicability for analysis of plasma chemical oxidation and ignition of low-temperature H(2)-air, CH(4)-air and C(2)H(4)-air mixtures using nanosecond pulse discharges. Kinetic modelling of low-temperature plasma excited propane-air mixtures demonstrates the need for development of a more accurate

  11. Quantitative Analysis of Mixture Preparation Processes in New Direct-Injection Spark Ignition Engines

    NASA Astrophysics Data System (ADS)

    Itoh, Teruyuki; Kakuho, Akihiko; Hiraya, Koji; Takahashi, Eiji; Urushihara, Tomonori

    Visualization plays an effective role in the establishment of a new combustion concept by helping to find the optimal results quickly among many different parameters and contributing to a shorter development period. Laser-induced fluorescence, Raman scattering and infrared absorption were used to measure the air/fuel ratio quantitatively in a third-generation direct-injection gasoline (DIG) engine with a spray-guided mixture formation process and comparisons were made with the mixture formation concepts of the first- and second-generation DIG engines. The optimum combination of fuel spray, gas flow and combustion chamber configuration was found to be different for the three generations of DIG engines. The characteristics of the stable combustion region for obtaining higher thermal efficiency and cleaner exhaust emissions differed among the three mixture formation concepts.

  12. Nursing Supplies

    MedlinePlus

    ... Stages Listen Español Text Size Email Print Share Nursing Supplies Page Content Article Body Throughout most of ... budget. (Nursing equipment also makes wonderful baby gifts.) Nursing Bras A well-made nursing bra that comfortably ...

  13. Variations in the structure and electrochemical characteristics of membrane electrode assemblies during the endurance testing of hydrogen-air fuel cells

    NASA Astrophysics Data System (ADS)

    Avakov, V. B.; Aliev, A. D.; Bogdanovskaya, V. A.; Ivanitskii, B. A.; Kazanskii, L. P.; Kapustin, A. V.; Korchagin, O. V.; Landgraf, I. K.; Tarasevich, M. P.; Chalykh, A. E.

    2015-05-01

    Variations in the characteristics of a membrane-electrode assembly (MEA) are studied during the endurance testing of a hydrogen-air fuel cell (FC) based on a Nafion 212 proton conducting membrane and platinum catalysts. It is shown that the voltage drop observed during MEA testing was mainly due to physicochemical transformations of the cathode catalyst, i.e., the oxidation of platinum and its subsequent recrystallization with nanoparticle coarsening. It is established that the rate of degradation increases along with temperature and loading, and with periodic FC depressurization. It is concluded that the enhancing effects of additional factors of degradation, e.g., platinum ion transport to the proton-conducting membrane and corrosion of the carbon carrier, were responsible for these processes.

  14. Flame kernel characterization of laser ignition of natural gas-air mixture in a constant volume combustion chamber

    NASA Astrophysics Data System (ADS)

    Srivastava, Dhananjay Kumar; Dharamshi, Kewal; Agarwal, Avinash Kumar

    2011-09-01

    In this paper, laser-induced ignition was investigated for compressed natural gas-air mixtures. Experiments were performed in a constant volume combustion chamber, which simulate end of the compression stroke conditions of a SI engine. This chamber simulates the engine combustion chamber conditions except turbulence of air-fuel mixture. It has four optical windows at diametrically opposite locations, which are used for laser ignition and optical diagnostics simultaneously. All experiments were conducted at 10 bar chamber pressure and 373 K chamber temperature. Initial stage of combustion phenomena was visualized by employing Shadowgraphy technique using a high speed CMOS camera. Flame kernel development of the combustible fuel-air mixture was investigated under different relative air-fuel ratios ( λ=1.2-1.7) and the images were interrogated for temporal propagation of flame front. Pressure-time history inside the combustion chamber was recorded and analyzed. This data is useful in characterizing the laser ignition of natural gas-air mixture and can be used in developing an appropriate laser ignition system for commercial use in SI engines.

  15. Nitric oxide density measurements in air and air/fuel nanosecond pulse discharges by laser induced fluorescence

    NASA Astrophysics Data System (ADS)

    Uddi, M.; Jiang, N.; Adamovich, I. V.; Lempert, W. R.

    2009-04-01

    Laser induced fluorescence is used to measure absolute nitric oxide concentrations in air, methane-air and ethylene-air non-equilibrium plasmas, as a function of time after initiation of a single pulse, 20 kV peak voltage, 25 ns pulse duration discharge. A mixture of NO and nitrogen with known composition (4.18 ppm NO) is used for calibration. Peak NO density in air at 60 Torr, after a single pulse, is ~8 × 1012 cm-3 (~4.14 ppm) occurring at ~250 µs after the pulse, with decay time of ~16.5 ms. Peak NO atom mole fraction in a methane-air mixture with equivalence ratio of phiv = 0.5 is found to be approximately equal to that in air, with approximately the same rise and decay rate. In an ethylene-air mixture (also with equivalence ratio of phiv = 0.5), the rise and decay times are comparable to air and methane-air, but the peak NO concentration is reduced by a factor of approximately 2.5. Spontaneous emission measurements show that excited electronic states N2(C 3Π) and NO(A 2Σ) in air at P = 60 Torr decay within ~20 ns and ~1 µs, respectively. Kinetic modelling calculations incorporating air plasma kinetics complemented with the GRI Mech 3.0 hydrocarbon oxidation mechanism are compared with the experimental data using three different NO production mechanisms. It is found that NO concentration rise after the discharge pulse is much faster than predicted by Zel'dovich mechanism reactions, by two orders of magnitude, but much slower compared with reactions of electronically excited nitrogen atoms and molecules, also by two orders of magnitude. It is concluded that processes involving long lifetime (~100 µs) metastable states, such as N2(X 1Σ,v) and O2(b 1Σ), formed by quenching of the metastable N2(A 3Σ) state by ground electronic state O2, may play a dominant role in NO formation. NO decay, in all cases, is found to be dominated by the reverse Zel'dovich reaction, NO + O → N + O2, as well as by conversion into NO2 in a reaction of NO with ozone.

  16. Power supply

    DOEpatents

    Yakymyshyn, Christopher Paul; Hamilton, Pamela Jane; Brubaker, Michael Allen

    2007-12-04

    A modular, low weight impedance dropping power supply with battery backup is disclosed that can be connected to a high voltage AC source and provide electrical power at a lower voltage. The design can be scaled over a wide range of input voltages and over a wide range of output voltages and delivered power.

  17. Power supply

    DOEpatents

    Hart, Edward J.; Leeman, James E.; MacDougall, Hugh R.; Marron, John J.; Smith, Calvin C.

    1976-01-01

    An electric power supply employs a striking means to initiate ferroelectric elements which provide electrical energy output which subsequently initiates an explosive charge which initiates a second ferroelectric current generator to deliver current to the coil of a magnetic field current generator, creating a magnetic field around the coil. Continued detonation effects compression of the magnetic field and subsequent generation and delivery of a large output current to appropriate output loads.

  18. Novel ferrocene-anchored ZnO nanoparticle/carbon nanotube assembly for glucose oxidase wiring: application to a glucose/air fuel cell

    NASA Astrophysics Data System (ADS)

    Haddad, Raoudha; Mattei, Jean-Gabriel; Thery, Jessica; Auger, Aurélien

    2015-06-01

    Glucose oxidase (GOx) is immobilized on ZnO nanoparticle-modified electrodes. The immobilized glucose oxidase shows efficient mediated electron transfer with ZnO nanoparticles to which the ferrocenyl moiety is π-stacked into a supramolecular architecture. The constructed ZnO-Fc/CNT modified electrode exhibits high ferrocene surface coverage, preventing any leakage of the π-stacked ferrocene from the newly described ZnO hybrid nanoparticles. The use of the new architecture of ZnO supported electron mediators to shuttle electrons from the redox centre of the enzyme to the surface of the working electrode can effectively bring about successful glucose oxidation. These modified electrodes evaluated as a highly efficient architecture provide a catalytic current for glucose oxidation and are integrated in a specially designed glucose/air fuel cell prototype using a conventional platinum-carbon (Pt/C) cathode at physiological pH (7.0). The obtained architecture leads to a peak power density of 53 μW cm-2 at 300 mV for the Nafion® based biofuel cell under ``air breathing'' conditions at room temperature.

  19. Novel ferrocene-anchored ZnO nanoparticle/carbon nanotube assembly for glucose oxidase wiring: application to a glucose/air fuel cell.

    PubMed

    Haddad, Raoudha; Mattei, Jean-Gabriel; Thery, Jessica; Auger, Aurélien

    2015-06-28

    Glucose oxidase (GOx) is immobilized on ZnO nanoparticle-modified electrodes. The immobilized glucose oxidase shows efficient mediated electron transfer with ZnO nanoparticles to which the ferrocenyl moiety is π-stacked into a supramolecular architecture. The constructed ZnO-Fc/CNT modified electrode exhibits high ferrocene surface coverage, preventing any leakage of the π-stacked ferrocene from the newly described ZnO hybrid nanoparticles. The use of the new architecture of ZnO supported electron mediators to shuttle electrons from the redox centre of the enzyme to the surface of the working electrode can effectively bring about successful glucose oxidation. These modified electrodes evaluated as a highly efficient architecture provide a catalytic current for glucose oxidation and are integrated in a specially designed glucose/air fuel cell prototype using a conventional platinum-carbon (Pt/C) cathode at physiological pH (7.0). The obtained architecture leads to a peak power density of 53 μW cm(-2) at 300 mV for the Nafion® based biofuel cell under "air breathing" conditions at room temperature.

  20. Fuel supply control method for internal combustion engines after starting in hot state

    SciTech Connect

    Fujimura, A.; Wazaki, Y.

    1988-08-23

    This patent describes a method of controlling the supply of fuel to an internal combustion engine, including the steps of effecting after-start fuel increasing control wherein an initial value of a fuel increment is set to a value dependent upon a temperature of the engine upon generation of a predetermined control signal immediately after the start of the engine, the fuel increment is progressively decreased from the set initial value in synchronism with subsequent generation of the predetermined control signal, and a fuel quantity corrected by the progressively decreased fuel increment is supplied to the engine, and effecting air-fuel ratio feedback control, which is executed on condition that a predetermined feedback control condition is fulfilled after the start of the engine, wherein a correction coefficient has a value thereof set to a value dependent upon the concentration of an ingredient in exhaust gases emitted from the engine, sensed by sensor means arranged in an exhaust system of the engine, and a fuel quantity corrected by the set correction coefficient is supplied to the engine, the improvement comprising the steps of: (a) setting the initial value of the fuel increment to smaller values as the temperature of the engine is higher; (b) setting the initial value of the fuel increment to a predetermined lower limit if the initial value set depending upon the temperature of the engine is smaller than the predetermined lower limit; and (c) effecting the air-fuel ratio feedback control by correcting a fuel quantity to be supplied to the engine by the fuel increment together with the correction coefficient insofar as the predetermined feedback control condition is fulfilled, when the temperature of the engine is higher than a predetermined value at the start of the engine.

  1. Cleaning supplies and equipment

    MedlinePlus

    ... gov/ency/patientinstructions/000443.htm Cleaning supplies and equipment To use the sharing features on this page, ... to clean supplies and equipment. Disinfecting Supplies and Equipment Start by wearing the right personal protective equipment ( ...

  2. Health supply chain management.

    PubMed

    Zimmerman, Rolf; Gallagher, Pat

    2010-01-01

    This chapter gives an educational overview of: * The actual application of supply chain practice and disciplines required for service delivery improvement within the current health environment. * A rationale for the application of Supply Chain Management (SCM) approaches to the Health sector. * The tools and methods available for supply chain analysis and benchmarking. * Key supply chain success factors.

  3. Symmetric normal mixtures

    NASA Technical Reports Server (NTRS)

    Turmon, Michael

    2004-01-01

    We consider mixture density estimation under the symmetry constraint x = Az for an orthogonal matrix A. This distributional constraint implies a corresponding constraint on the mixture parameters. Focusing on the gaussian case, we derive an expectation-maximization (EM) algorithm to enforce the constraint and show results for modeling of image feature vectors.

  4. Near azeotropic mixture substitute

    NASA Technical Reports Server (NTRS)

    Jones, Jack A. (Inventor)

    1996-01-01

    The present invention comprises a refrigerant mixture consisting of a first mole fraction of 1,1,1,2-tetrafluoroethane (R134a) and a second mole fraction of a component selected from the group consisting of a mixture of CHClFCF.sub.3 (R124) and CH.sub.3 CClF.sub.2 (R142b); a mixture of CHF.sub.2 CH.sub.3 (R152a) and CHClFCF.sub.3 (R124); a mixture of CHF.sub.2 CH.sub.3 (R152a) and CH.sub.3 CClF.sub.2 (R142b); and a mixture of CHClFCF.sub.3 (R124), CH.sub.3 CClF.sub.2 (R142b) and CHF.sub.2 CH.sub.3 (R152a).

  5. Perception of trigeminal mixtures.

    PubMed

    Filiou, Renée-Pier; Lepore, Franco; Bryant, Bruce; Lundström, Johan N; Frasnelli, Johannes

    2015-01-01

    The trigeminal system is a chemical sense allowing for the perception of chemosensory information in our environment. However, contrary to smell and taste, we lack a thorough understanding of the trigeminal processing of mixtures. We, therefore, investigated trigeminal perception using mixtures of 3 relatively receptor-specific agonists together with one control odor in different proportions to determine basic perceptual dimensions of trigeminal perception. We found that 4 main dimensions were linked to trigeminal perception: sensations of intensity, warmth, coldness, and pain. We subsequently investigated perception of binary mixtures of trigeminal stimuli by means of these 4 perceptual dimensions using different concentrations of a cooling stimulus (eucalyptol) mixed with a stimulus that evokes warmth perception (cinnamaldehyde). To determine if sensory interactions are mainly of central or peripheral origin, we presented stimuli in a physical "mixture" or as a "combination" presented separately to individual nostrils. Results showed that mixtures generally yielded higher ratings than combinations on the trigeminal dimensions "intensity," "warm," and "painful," whereas combinations yielded higher ratings than mixtures on the trigeminal dimension "cold." These results suggest dimension-specific interactions in the perception of trigeminal mixtures, which may be explained by particular interactions that may take place on peripheral or central levels.

  6. SEPARATION OF FLUID MIXTURES

    DOEpatents

    Lipscomb, R.; Craig, A.; Labrow, S.; Dunn, J.F.

    1958-10-28

    An apparatus is presented for separating gaseous mixtures by selectively freezing a constituent of the mixture and subsequently separating the frozen gas. The gas mixture is passed through a cylinder fltted with a cooling jacket, causing one gas to freeze on the walls of the cylinder. A set of scraper blades are provided in the interior of the cyllnder, and as the blades oscillate, the frozen gas is scraped to the bottom of the cylinder. Means are provided for the frozen material to pass into a heating chamber where it is vaporized and the product gas collected.

  7. Combustion of novel chemical mixtures for hydrogen generation

    SciTech Connect

    Shafirovich, Evgeny; Diakov, Victor; Varma, Arvind

    2006-01-01

    Novel chemical compositions for combustion-based generation of hydrogen, which can be used to feed fuel cells for emergency power supplies and portable electronics, are reported. Combustion heat release from the proposed gas-generating compositions can be converted to electricity. The proposed sodium borohydride/aluminum/water mixtures are combustible and exhibit high hydrogen yield. Mixtures with 50-70 wt% of Al are promising to obtain simultaneously high H{sub 2} yield and stable self-sustained combustion.

  8. Feedstock Supply System Logistics

    SciTech Connect

    2006-06-01

    Feedstock supply is a significant cost component in the production of biobased fuels, products, and power. The uncertainty of the biomass feedstock supply chain and associated risks are major barriers to procuring capital funding for start-up biorefineries.

  9. Carbonaceous materials water mixtures

    SciTech Connect

    Papalos, J.G.; Sinka, J.V.

    1985-04-30

    Particulate carbonaceous materials water mixtures are prepared by adding a condensate which is a condensation product of an aldehyde having from about 1 to about 7 carbon atoms, a benzene derivative such as benzene sulfonic acid, an alkyl benzene sulfonic acid having at least one alkyl group of from about 1 to about 20 carbon atoms and mixtures thereof, and optionally, and a naphthalene derivative such as naphthalene sulfonic acid, an alkyl naphthalene sulfonic acid having at least one alkyl group of from about 1 to about 12 carbon atoms and mixtures thereof. The condensate is added in an amount sufficient to reduce viscosity of the water mixture of carbonaceous materials, to stabilize carbonaceous materials in the water network and to improve pumpability. An acid form of the condensate or a salt may be added.

  10. Condensate Mixtures and Tunneling

    SciTech Connect

    Timmermans, E.

    1998-09-14

    The experimental study of condensate mixtures is a particularly exciting application of the recently developed atomic-trap Bose-Einstein condensate (BEC) technology: such multiple condensates represent the first laboratory systems of distinguishable boson superfluid mixtures. In addition, as the authors point out in this paper, the possibility of inter-condensate tunneling greatly enhances the richness of the condensate mixture physics. Not only does tunneling give rise to the oscillating particle currents between condensates of different chemical potentials, such as those studied extensively in the condensed matter Josephson junction experiments, it also affects the near-equilibrium dynamics and stability of the condensate mixtures. In particular, the stabilizing influence of tunneling with respect to spatial separation (phase separation) could be of considerable practical importance to the atomic trap systems. Furthermore, the creation of mixtures of atomic and molecular condensates could introduce a novel type of tunneling process, involving the conversion of a pair of atomic condensate bosons into a single molecular condensate boson. The static description of condensate mixtures with such type of pair tunneling suggests the possibility of observing dilute condensates with the liquid-like property of a self-determined density.

  11. Pursuing supply chain gains.

    PubMed

    Long, Gene

    2005-09-01

    Five hallmarks of an effective supply chain are: A strong relationship is developed with a single GPO. Physicians are involved in supply standardization. Supply contracts are routinely reviewed at time of renewal. Freight costs are understood and negotiated effectively. Products are distributed through an in-house distribution center.

  12. Controlling supply expenses through capitated supply contracting.

    PubMed

    Kowalski, J C

    1997-07-01

    Some providers dealing with the financial challenges of managed care are attempting to control supply expenses through capitated supply contracting and similar risk/reward sharing arrangements. Under such arrangements, a supplier sells products and services to a provider for a fixed, prospective price in exchange for the provider's exclusive business. If expenses exceed the prospectively established amount, the supplier and provider share the loss. Conversely, if expenses are less than the fixed amount, they share the savings. For a capitated supply arrangement to be successful, providers must be able to identify and track supply expense drivers, such as clinical pathways, technology utilization, and product selection and utilization. Sophisticated information systems are needed to capture data, such as total and per-transaction product usage/volume; unit price per item; average and cost per item; average and total cost per transaction; and total cost per outcome. Providers also will need to establish mutually cooperative relationships with the suppliers with whom they contract.

  13. Preprototype nitrogen supply subsystem development

    NASA Technical Reports Server (NTRS)

    Heppner, D. B.; Hallick, T. M.; Schubert, F. H.

    1981-01-01

    A nitrogen supply subsystem based on the dissociation of hydrazine into a mixture of hydrogen and nitrogen is developed. The latter is separated to provide makeup nitrogen to control the composition of spacecraft atmospheres. Specific hardware developments resulted in the design and fabrication of a nominal 3.6 kg/d nitrogen generation module. The design integrates a hydrazine catalytic dissociator, three ammonia dissociation stages and four hydrogen separation stages into a 33 kg, 14 cu dm module. A technique was devised to alternate the ammonia dissociation and hydrogen separation stages to give high nitrogen purity in the end product stream. Tests show the product stream to contain less than 0.5 percent hydrogen and 10 parts per million ammonia. The design and development of a test stand for the nitrogen generation module and a series of tests which verified its operation and performance capability are described.

  14. Fuel cell integrated with steam reformer

    DOEpatents

    Beshty, Bahjat S.; Whelan, James A.

    1987-01-01

    A H.sub.2 -air fuel cell integrated with a steam reformer is disclosed wherein a superheated water/methanol mixture is fed to a catalytic reformer to provide a continuous supply of hydrogen to the fuel cell, the gases exhausted from the anode of the fuel cell providing the thermal energy, via combustion, for superheating the water/methanol mixture.

  15. Competing for supply.

    PubMed

    Stolle, B

    2001-02-01

    The Internet was supposed to make it possible for anybody anywhere to get anything anytime. Instead, it's magnified suppliers' miscalculations into global shortages. But if the Net caused these supply chain woes, it's also the solution, says the CEO of a supply-chain software manufacturer.

  16. Power supply conditioning circuit

    NASA Technical Reports Server (NTRS)

    Primas, L. E.; Loveland, R.

    1987-01-01

    A power supply conditioning circuit that can reduce Periodic and Random Deviations (PARD) on the output voltages of dc power supplies to -150 dBV from dc to several KHz with no measurable periodic deviations is described. The PARD for a typical commercial low noise power supply is -74 dBV for frequencies above 20 Hz and is often much worse at frequencies below 20 Hz. The power supply conditioning circuit described here relies on the large differences in the dynamic impedances of a constant current diode and a zener diode to establish a dc voltage with low PARD. Power supplies with low PARD are especially important in circuitry involving ultrastable frequencies for the Deep Space Network.

  17. Spatial Data Supply Chains

    NASA Astrophysics Data System (ADS)

    Varadharajulu, P.; Azeem Saqiq, M.; Yu, F.; McMeekin, D. A.; West, G.; Arnold, L.; Moncrieff, S.

    2015-06-01

    This paper describes current research into the supply of spatial data to the end user in as close to real time as possible via the World Wide Web. The Spatial Data Infrastructure paradigm has been discussed since the early 1990s. The concept has evolved significantly since then but has almost always examined data from the perspective of the supplier. It has been a supplier driven focus rather than a user driven focus. The current research being conducted is making a paradigm shift and looking at the supply of spatial data as a supply chain, similar to a manufacturing supply chain in which users play a significant part. A comprehensive consultation process took place within Australia and New Zealand incorporating a large number of stakeholders. Three research projects that have arisen from this consultation process are examining Spatial Data Supply Chains within Australia and New Zealand and are discussed within this paper.

  18. Prevalence Incidence Mixture Models

    Cancer.gov

    The R package and webtool fits Prevalence Incidence Mixture models to left-censored and irregularly interval-censored time to event data that is commonly found in screening cohorts assembled from electronic health records. Absolute and relative risk can be estimated for simple random sampling, stratified sampling, and two-phase stratified sampling. Non-parametric (absolute risks only), semi-parametric, weakly-parametric (using B-splines), and some fully parametric (such as the logistic-Weibull) models are supported.

  19. Hydrogen supply system

    SciTech Connect

    Teitel, R.J.

    1981-11-24

    A system for supplying hydrogen to an apparatus which utilizes hydrogen contains a metal hydride hydrogen supply component and a microcavity hydrogen storage hydrogen supply component which in tandem supply hydrogen for the apparatus. The metal hydride hydrogen supply component includes a first storage tank filled with a composition which is capable of forming a metal hydride of such a nature that the hydride will release hydrogen when heated but will absorb hydrogen when cooled. This first storage tank is equipped with a heat exchanger for both adding heat to and extracting heat from the composition to regulate the absorption/deabsorption of hydrogen from the composition. The microcavity hydrogen storage hydrogen supply component includes a second tank containing the microcavity hydrogen supply. The microcavity hydrogen storage contains hydrogen held under high pressure within individual microcavities. The hydrogen is released from the microcavities by heating the cavities. This heating is accomplished by including within the tank for the microcavity hydrogen storage a heating element.

  20. Automating power supply checkout

    SciTech Connect

    Laster, J.; Bruno, D.; D'Ottavio, T.; Drozd, J.; Marr, G.; Mi, C.

    2011-03-28

    Power Supply checkout is a necessary, pre-beam, time-critical function. At odds are the desire to decrease the amount of time to perform the checkout while at the same time maximizing the number and types of checks that can be performed and analyzing the results quickly (in case any problems exist that must be addressed). Controls and Power Supply Group personnel have worked together to develop tools to accomplish these goals. Power Supply checkouts are now accomplished in a time-frame of hours rather than days, reducing the number of person-hours needed to accomplish the checkout and making the system available more quickly for beam development. The goal of the Collider-Accelerator Department (CAD) at Brookhaven National Laboratory is to provide experimenters with collisions of heavy-ions and polarized protons. The Relativistic Heavy-Ion Collider (RHIC) magnets are controlled by 100's of varying types of power supplies. There is a concentrated effort to perform routine maintenance on the supplies during shutdown periods. There is an effort at RHIC to streamline the time needed for system checkout in order to quickly arrive at a period of beam operations for RHIC. This time-critical period is when the checkout of the power supplies is performed as the RHIC ring becomes cold and the supplies are connected to their physical magnets. The checkout process is used to identify problems in voltage and current regulation by examining data signals related to each for problems in settling and regulation (ripple).

  1. Supply chain planning classification

    NASA Astrophysics Data System (ADS)

    Hvolby, Hans-Henrik; Trienekens, Jacques; Bonde, Hans

    2001-10-01

    Industry experience a need to shift in focus from internal production planning towards planning in the supply network. In this respect customer oriented thinking becomes almost a common good amongst companies in the supply network. An increase in the use of information technology is needed to enable companies to better tune their production planning with customers and suppliers. Information technology opportunities and supply chain planning systems facilitate companies to monitor and control their supplier network. In spite if these developments, most links in today's supply chains make individual plans, because the real demand information is not available throughout the chain. The current systems and processes of the supply chains are not designed to meet the requirements now placed upon them. For long term relationships with suppliers and customers, an integrated decision-making process is needed in order to obtain a satisfactory result for all parties. Especially when customized production and short lead-time is in focus. An effective value chain makes inventory available and visible among the value chain members, minimizes response time and optimizes total inventory value held throughout the chain. In this paper a supply chain planning classification grid is presented based current manufacturing classifications and supply chain planning initiatives.

  2. Supply chain assessment methodology.

    PubMed

    Topor, E

    2000-08-01

    This article describes an assessment methodology based on the supply chain proficiency model that can be used to set realistic supply chain objectives. The assessment centers on a business model that identifies the logical stages of supply chain proficiency as measured against a comprehensive set of business characteristics. For each characteristic, an enterprise evolves from one stage to the next. The magnitude of change inherent in moving forward usually prohibits skipping stages. Although it is possible to be at different stages for each characteristic, it is usually desirable to maintain balance.

  3. Managing Supply Chain Disruptions

    DTIC Science & Technology

    2008-08-09

    functions within and across organizations (CSCMP, 2005). Mentzer et al. (2001) characterize SCM as a philosophy that includes a systems approach with...150 vi LIST OF TABLES Table 2.1. Prominent Supply Chain Related System Theory...process. It is not a matter of a supply chain system encountering a problem, but rather a matter of when a problematic event will occur and how severe

  4. Environmental complex mixture toxicity assessment.

    PubMed

    Gardner, H S; Brennan, L M; Toussaint, M W; Rosencrance, A B; Boncavage-Hennessey, E M; Wolfe, M J

    1998-12-01

    Trichloroethylene (TCE) was found as a contaminant in the well supplying water to an aquatic testing laboratory. The groundwater was routinely screened by a commercial laboratory for volatile and semivolatile compounds, metals, herbicides, pesticides, and polychlorinated biphenyls using U.S. Environmental Protection Agency methods. Although TCE was the only reportable peak on the gas chromatograph, with average concentrations of 0.200 mg/l, other small peaks were also present, indicating the possibility that the contamination was not limited to TCE alone. A chronic 6-month carcinogenicity assay was conducted on-site in a biomonitoring trailer, using the Japanese medaka fish (Oryzias latipes) in an initiation-promotion protocol, with diethylnitrosamine (DEN) as the initiator and the TCE-contaminated groundwater as a promoter. Study results indicated no evidence of carcinogenic potential of the groundwater without initiation. There was, however, a tumor-promotional effect of the groundwater after DEN initiation. A follow-up laboratory study was conducted using reagent grade TCE added to carbon-filtered groundwater to simulate TCE concentrations comparable to those found in the contaminated groundwater. Study results indicated no promotional effects of TCE. These studies emphasize the necessity for on-site bioassays to assess potential environmental hazards. In this instance, chemical analysis of the groundwater identified TCE as the only reportable contaminant, but other compounds present below reportable limits were noted and may have had a synergistic effect on tumor promotion observed with the groundwater exposure. Laboratory toxicity testing of single compounds can produce toxicity data specific to that compound for that species but cannot take into account the possible toxic effects of mixtures of compounds.

  5. Environmental complex mixture toxicity assessment.

    PubMed Central

    Gardner, H S; Brennan, L M; Toussaint, M W; Rosencrance, A B; Boncavage-Hennessey, E M; Wolfe, M J

    1998-01-01

    Trichloroethylene (TCE) was found as a contaminant in the well supplying water to an aquatic testing laboratory. The groundwater was routinely screened by a commercial laboratory for volatile and semivolatile compounds, metals, herbicides, pesticides, and polychlorinated biphenyls using U.S. Environmental Protection Agency methods. Although TCE was the only reportable peak on the gas chromatograph, with average concentrations of 0.200 mg/l, other small peaks were also present, indicating the possibility that the contamination was not limited to TCE alone. A chronic 6-month carcinogenicity assay was conducted on-site in a biomonitoring trailer, using the Japanese medaka fish (Oryzias latipes) in an initiation-promotion protocol, with diethylnitrosamine (DEN) as the initiator and the TCE-contaminated groundwater as a promoter. Study results indicated no evidence of carcinogenic potential of the groundwater without initiation. There was, however, a tumor-promotional effect of the groundwater after DEN initiation. A follow-up laboratory study was conducted using reagent grade TCE added to carbon-filtered groundwater to simulate TCE concentrations comparable to those found in the contaminated groundwater. Study results indicated no promotional effects of TCE. These studies emphasize the necessity for on-site bioassays to assess potential environmental hazards. In this instance, chemical analysis of the groundwater identified TCE as the only reportable contaminant, but other compounds present below reportable limits were noted and may have had a synergistic effect on tumor promotion observed with the groundwater exposure. Laboratory toxicity testing of single compounds can produce toxicity data specific to that compound for that species but cannot take into account the possible toxic effects of mixtures of compounds. Images Figure 2 PMID:9860885

  6. Binomial Gaussian mixture filter

    NASA Astrophysics Data System (ADS)

    Raitoharju, Matti; Ali-Löytty, Simo; Piché, Robert

    2015-12-01

    In this work, we present a novel method for approximating a normal distribution with a weighted sum of normal distributions. The approximation is used for splitting normally distributed components in a Gaussian mixture filter, such that components have smaller covariances and cause smaller linearization errors when nonlinear measurements are used for the state update. Our splitting method uses weights from the binomial distribution as component weights. The method preserves the mean and covariance of the original normal distribution, and in addition, the resulting probability density and cumulative distribution functions converge to the original normal distribution when the number of components is increased. Furthermore, an algorithm is presented to do the splitting such as to keep the linearization error below a given threshold with a minimum number of components. The accuracy of the estimate provided by the proposed method is evaluated in four simulated single-update cases and one time series tracking case. In these tests, it is found that the proposed method is more accurate than other Gaussian mixture filters found in the literature when the same number of components is used and that the proposed method is faster and more accurate than particle filters.

  7. Petroleum Supply Monthly

    SciTech Connect

    1996-02-01

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  8. Petroleum supply monthly

    SciTech Connect

    1995-10-01

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blends, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  9. Toxicological approaches to complex mixtures.

    PubMed Central

    Mauderly, J L

    1993-01-01

    This paper reviews the role of toxicological studies in understanding the health effects of environmental exposures to mixtures. The approach taken is to review mixtures that have received the greatest emphasis from toxicology; major mixtures research programs; the toxicologist's view of mixtures and approaches to their study; and the complementary roles of toxicological, clinical, and epidemiological studies. Studies of tobacco smoke, engine exhaust, combustion products, and air pollutants comprise most of the past research on mixtures. Because of their great experimental control over subjects, exposures, and endpoints, toxicologists tend to consider a wider range of toxic interactions among mixture components and sequential exposures than is practical for human studies. The three fundamental experimental approaches used by toxicologists are integrative (studying the mixture as a whole), dissective (dissecting a mixture to determine causative constituents), and synthetic (studying interactions between agents in simple combinations). Toxicology provides information on potential hazards, mechanisms by which mixture constituents interact to cause effects, and exposure dose-effect relationships; but extrapolation from laboratory data to quantitative human health risks is problematic. Toxicological, clinical, and epidemiological approaches are complementary but are seldom coordinated. Fostering synergistic interactions among the disciplines in studying the risks from mixtures could be advantageous. PMID:7515806

  10. Fluidizing a mixture of particulate coal and char

    DOEpatents

    Green, Norman W.

    1979-08-07

    Method of mixing particulate materials comprising contacting a primary source and a secondary source thereof whereby resulting mixture ensues; preferably at least one of the two sources has enough motion to insure good mixing and the particulate materials may be heat treated if desired. Apparatus for such mixing comprising an inlet for a primary source, a reactor communicating therewith, a feeding means for supplying a secondary source to the reactor, and an inlet for the secondary source. Feeding means is preferably adapted to supply fluidized materials.

  11. Mixtures and Mineral Reactions

    NASA Astrophysics Data System (ADS)

    Rumble, D.

    The monograph Mixtures and Mineral Reactions contains a large amount of information of value to mineralogists, petrologists, and geochemists. The first four chapters are a succinct account of the thermodynamic description of crystalline solutions. In these early chapters a comparison is made between different mathematical treatments of activitycomposition models, there is a discussion of the unmixing by exsolution of a single solution into two phases, and methods of computing phase equilibria in assemblages of different minerals are given. If the reader is perplexed by the discussion of standard states (cf. Figure 1.3), not to worry. That is a normal condition for anyone forced to choose between equivalent reference frames yet knowing, somewhere down the line, that the choice will ultimately make one's computational life more or less difficult.

  12. Perioperative supply chain management.

    PubMed

    Feistritzer, N R; Keck, B R

    2000-09-01

    Faced with declining revenues and increasing operating expenses, hospitals are evaluating numerous mechanisms designed to reduce costs while simultaneously maintaining quality care. Many facilities have targeted initial cost reduction efforts in the reduction of labor expenses. Once labor expenses have been "right sized," facilities have continued to focus on service delivery improvements by the optimization of the "supply chain" process. This report presents a case study of the efforts of Vanderbilt University Medical Center in the redesign of its supply chain management process in the department of Perioperative Services. Utilizing a multidisciplinary project management structure, 3 work teams were established to complete the redesign process. To date, the project has reduced costs by $2.3 million and enhanced quality patient care by enhancing the delivery of appropriate clinical supplies during the perioperative experience.

  13. Coal supply for California

    NASA Technical Reports Server (NTRS)

    Yancik, J. J.

    1978-01-01

    The potential sources and qualities of coals available for major utility and industrial consumers in California are examined and analyzed with respect to those factors that would affect the reliability of supplies. Other considerations, such as the requirements and assurances needed by the coal producers to enter into long-term contracts and dedicate large reserves of coal to these contracts are also discussed. Present and potential future mining contraints on coal mine operators are identified and analyzed with respect to their effect on availability of supply.

  14. Supply-Chain Optimization Template

    NASA Technical Reports Server (NTRS)

    Quiett, William F.; Sealing, Scott L.

    2009-01-01

    The Supply-Chain Optimization Template (SCOT) is an instructional guide for identifying, evaluating, and optimizing (including re-engineering) aerospace- oriented supply chains. The SCOT was derived from the Supply Chain Council s Supply-Chain Operations Reference (SCC SCOR) Model, which is more generic and more oriented toward achieving a competitive advantage in business.

  15. Modeling of active transmembrane transport in a mixture theory framework.

    PubMed

    Ateshian, Gerard A; Morrison, Barclay; Hung, Clark T

    2010-05-01

    This study formulates governing equations for active transport across semi-permeable membranes within the framework of the theory of mixtures. In mixture theory, which models the interactions of any number of fluid and solid constituents, a supply term appears in the conservation of linear momentum to describe momentum exchanges among the constituents. In past applications, this momentum supply was used to model frictional interactions only, thereby describing passive transport processes. In this study, it is shown that active transport processes, which impart momentum to solutes or solvent, may also be incorporated in this term. By projecting the equation of conservation of linear momentum along the normal to the membrane, a jump condition is formulated for the mechano-electrochemical potential of fluid constituents which is generally applicable to nonequilibrium processes involving active transport. The resulting relations are simple and easy to use, and address an important need in the membrane transport literature.

  16. Lightweight Regulated Power Supply

    NASA Technical Reports Server (NTRS)

    Mclyman, C. W.

    1985-01-01

    Power-supply circuit regulates output voltage by adjusting frequency of chopper circuit according to variations. Currently installed in battery charger for electric wheelchair, circuit is well suited to other uses in which light weight is important - for example, in portable computers, radios, and test instruments.

  17. Teleconnected food supply shocks

    NASA Astrophysics Data System (ADS)

    Bren d'Amour, Christopher; Wenz, Leonie; Kalkuhl, Matthias; Steckel, Jan Christoph; Creutzig, Felix

    2016-03-01

    The 2008-2010 food crisis might have been a harbinger of fundamental climate-induced food crises with geopolitical implications. Heat-wave-induced yield losses in Russia and resulting export restrictions led to increases in market prices for wheat across the Middle East, likely contributing to the Arab Spring. With ongoing climate change, temperatures and temperature variability will rise, leading to higher uncertainty in yields for major nutritional crops. Here we investigate which countries are most vulnerable to teleconnected supply-shocks, i.e. where diets strongly rely on the import of wheat, maize, or rice, and where a large share of the population is living in poverty. We find that the Middle East is most sensitive to teleconnected supply shocks in wheat, Central America to supply shocks in maize, and Western Africa to supply shocks in rice. Weighing with poverty levels, Sub-Saharan Africa is most affected. Altogether, a simultaneous 10% reduction in exports of wheat, rice, and maize would reduce caloric intake of 55 million people living in poverty by about 5%. Export bans in major producing regions would put up to 200 million people below the poverty line at risk, 90% of which live in Sub-Saharan Africa. Our results suggest that a region-specific combination of national increases in agricultural productivity and diversification of trade partners and diets can effectively decrease future food security risks.

  18. Exploration Supply Chain Simulation

    NASA Technical Reports Server (NTRS)

    2008-01-01

    The Exploration Supply Chain Simulation project was chartered by the NASA Exploration Systems Mission Directorate to develop a software tool, with proper data, to quantitatively analyze supply chains for future program planning. This tool is a discrete-event simulation that uses the basic supply chain concepts of planning, sourcing, making, delivering, and returning. This supply chain perspective is combined with other discrete or continuous simulation factors. Discrete resource events (such as launch or delivery reviews) are represented as organizational functional units. Continuous resources (such as civil service or contractor program functions) are defined as enabling functional units. Concepts of fixed and variable costs are included in the model to allow the discrete events to interact with cost calculations. The definition file is intrinsic to the model, but a blank start can be initiated at any time. The current definition file is an Orion Ares I crew launch vehicle. Parameters stretch from Kennedy Space Center across and into other program entities (Michaud Assembly Facility, Aliant Techsystems, Stennis Space Center, Johnson Space Center, etc.) though these will only gain detail as the file continues to evolve. The Orion Ares I file definition in the tool continues to evolve, and analysis from this tool is expected in 2008. This is the first application of such business-driven modeling to a NASA/government-- aerospace contractor endeavor.

  19. Supply chain management.

    PubMed

    Palevich, R F

    1999-02-01

    This article describes how Do It Best Corp. has used technology to improve its supply chain management. Among other topics it discusses the company's use of electronic data interchange, the Internet, electronic forecasting, and warehouse management systems to gain substantial savings and increase its competitiveness.

  20. Maintenance and supply options

    NASA Technical Reports Server (NTRS)

    1988-01-01

    The object of the Maintenance and Supply Option was to develop a high level operational philosophy related to maintenance and supply operations and incorporate these concepts into the Lunar Base Study. Specific products to be generated during this task were three trade studies and a conceptual design of the Logistic Supply Module. The crew size study was performed to evaluate crew sizes from the baseline size of four to a crew size of eight and determine the preferred crew size. The second trade study was to determine the impact of extending surface stay times and recommend a preferred duration of stay time as a function of crew, consumables, and equipment support capabilities. The third trade study was an evaluation of packaging and storage methods to determine the preferred logistics approach to support the lunar base. A modified scenario was developed and served as the basis of the individual trade studies. Assumptions and guidelines were also developed from experience with Apollo programs, Space Shuttle operations, and Space Station studies. With this information, the trade studies were performed and a conceptual design for the Logistic Supply Module was developed.

  1. Supply and Demand

    MedlinePlus

    ... breast to continue producing an adequate supply of milk. In fact, the protein contained in the residual milk remaining in the ... or fluid) content, and the composition of your milk will change. Over the next week or so, the protein content will decline and the fat and lactose ...

  2. Baby supplies you need

    MedlinePlus

    ... Newborn care - baby supplies References Carlo WA. The newborn infant. In: Kliegman RM, Stanton BF, St Geme JW, ... A.M. Editorial team. Related MedlinePlus Health Topics Infant and Newborn Care Browse the Encyclopedia A.D.A.M., ...

  3. Supply chain quality.

    PubMed

    Feary, Simon

    2009-01-01

    As the development of complex manufacturing models and virtual companies become more prevalent in today's growing global markets, it is increasingly important to support the relationships between manufacturer and supplier. Utilising these relationships will ensure that supply chains operate more effectively and reduce costs, risks and time-to-market time frames, whilst maintaining product quality.

  4. Effect of flow velocity and temperature on ignition characteristics in laser ignition of natural gas and air mixtures

    NASA Astrophysics Data System (ADS)

    Griffiths, J.; Riley, M. J. W.; Borman, A.; Dowding, C.; Kirk, A.; Bickerton, R.

    2015-03-01

    Laser induced spark ignition offers the potential for greater reliability and consistency in ignition of lean air/fuel mixtures. This increased reliability is essential for the application of gas turbines as primary or secondary reserve energy sources in smart grid systems, enabling the integration of renewable energy sources whose output is prone to fluctuation over time. This work details a study into the effect of flow velocity and temperature on minimum ignition energies in laser-induced spark ignition in an atmospheric combustion test rig, representative of a sub 15 MW industrial gas turbine (Siemens Industrial Turbomachinery Ltd., Lincoln, UK). Determination of minimum ignition energies required for a range of temperatures and flow velocities is essential for establishing an operating window in which laser-induced spark ignition can operate under realistic, engine-like start conditions. Ignition of a natural gas and air mixture at atmospheric pressure was conducted using a laser ignition system utilizing a Q-switched Nd:YAG laser source operating at 532 nm wavelength and 4 ns pulse length. Analysis of the influence of flow velocity and temperature on ignition characteristics is presented in terms of required photon flux density, a useful parameter to consider during the development laser ignition systems.

  5. Thermophysical Properties of Hydrocarbon Mixtures

    National Institute of Standards and Technology Data Gateway

    SRD 4 NIST Thermophysical Properties of Hydrocarbon Mixtures (PC database for purchase)   Interactive computer program for predicting thermodynamic and transport properties of pure fluids and fluid mixtures containing up to 20 components. The components are selected from a database of 196 components, mostly hydrocarbons.

  6. High voltage power supply

    NASA Technical Reports Server (NTRS)

    Ruitberg, A. P.; Young, K. M. (Inventor)

    1985-01-01

    A high voltage power supply is formed by three discrete circuits energized by a battery to provide a plurality of concurrent output signals floating at a high output voltage on the order of several tens of kilovolts. In the first two circuits, the regulator stages are pulse width modulated and include adjustable ressistances for varying the duty cycles of pulse trains provided to corresponding oscillator stages while the third regulator stage includes an adjustable resistance for varying the amplitude of a steady signal provided to a third oscillator stage. In the first circuit, the oscillator, formed by a constant current drive network and a tuned resonant network included a step up transformer, is coupled to a second step up transformer which, in turn, supplies an amplified sinusoidal signal to a parallel pair of complementary poled rectifying, voltage multiplier stages to generate the high output voltage.

  7. Discontinuous Mode Power Supply

    NASA Technical Reports Server (NTRS)

    Lagadinos, John; Poulos, Ethel

    2012-01-01

    A document discusses the changes made to a standard push-pull inverter circuit to avoid saturation effects in the main inverter power supply. Typically, in a standard push-pull arrangement, the unsymmetrical primary excitation causes variations in the volt second integral of each half of the excitation cycle that could lead to the establishment of DC flux density in the magnetic core, which could eventually cause saturation of the main inverter transformer. The relocation of the filter reactor normally placed across the output of the power supply solves this problem. The filter reactor was placed in series with the primary circuit of the main inverter transformer, and is presented as impedance against the sudden changes on the input current. The reactor averaged the input current in the primary circuit, avoiding saturation of the main inverter transformer. Since the implementation of the described change, the above problem has not reoccurred, and failures in the main power transistors have been avoided.

  8. Supply Chain Interoperability Measurement

    DTIC Science & Technology

    2015-06-19

    Supply Chain Interoperability Measurement DISSERTATION June 2015 Christos E. Chalyvidis, Major, Hellenic Air ...Force AFIT-ENS-DS-15-J-001 DEPARTMENT OF THE AIR FORCE AIR UNIVERSITY AIR FORCE INSTITUTE OF TECHNOLOGY Wright-Patterson Air Force...are those of the author and do not reflect the official policy or position of the United States Air Force, Department of Defense, or the United

  9. Streamlining the supply chain.

    PubMed

    Neumann, Lydon

    2003-07-01

    Effective management of the supply chain requires attention to: Product management--formulary development and maintenance, compliance, clinical involvement, standardization, and demand-matching. Sourcing and contracting--vendor consolidation, GPO portfolio management, price leveling, content management, and direct contracting Purchasing and payment-cycle--automatic placement, web enablement, centralization, evaluated receipts settlement, and invoice matching Inventory and distribution management--"unofficial" and "official" locations, vendor-managed inventory, automatic replenishment, and freight management.

  10. DIRECT AMMONIA-AIR FUEL CELL.

    DTIC Science & Technology

    Experimental runs were conducted on direct ammonia fuel cells . Effects of temperature, composition, as well as run effect and block effect were...cells and to electrode flooding are discussed. Data on performance of complete laboratory direct ammonia-oxygen fuel cells are presented and discussed. (Author)

  11. DIRECT AMMONIA-AIR FUEL CELL.

    DTIC Science & Technology

    fuel cell was investigated. This cell is based on the use of a non-aqueous fused hydroxide electrolyte matrix, and operates in the intermediate temperature range of 180-300 C. Studies have been carried out to determine the nature of the ratecontrolling step in the kinetics of the anodic oxidation of ammonia. A new type of Ni/NiOOH reference electrode was developed for the measurement of single electrode potentials in experimental galvanic fuel cells employing this type of matrix electrolyte. In addition to various exploratory studies, two statistical analysis

  12. A methanol/air fuel cell system

    NASA Technical Reports Server (NTRS)

    Asher, W. J.

    1974-01-01

    High power-density, self-regulating fuel cell develops electrical power from catalyzed reaction between methanol and atmospheric oxygen. Cells such as these are of particular interest, because they may one day offer an emission-free, extremely efficient alternative to internal-combustion engines as power source.

  13. Hydrogen/Air Fuel Nozzle Emissions Experiments

    NASA Technical Reports Server (NTRS)

    Smith, Timothy D.

    2001-01-01

    The use of hydrogen combustion for aircraft gas turbine engines provides significant opportunities to reduce harmful exhaust emissions. Hydrogen has many advantages (no CO2 production, high reaction rates, high heating value, and future availability), along with some disadvantages (high current cost of production and storage, high volume per BTU, and an unknown safety profile when in wide use). One of the primary reasons for switching to hydrogen is the elimination of CO2 emissions. Also, with hydrogen, design challenges such as fuel coking in the fuel nozzle and particulate emissions are no longer an issue. However, because it takes place at high temperatures, hydrogen-air combustion can still produce significant levels of NOx emissions. Much of the current research into conventional hydrocarbon-fueled aircraft gas turbine combustors is focused on NOx reduction methods. The Zero CO2 Emission Technology (ZCET) hydrogen combustion project will focus on meeting the Office of Aerospace Technology goal 2 within pillar one for Global Civil Aviation reducing the emissions of future aircraft by a factor of 3 within 10 years and by a factor of 5 within 25 years. Recent advances in hydrocarbon-based gas turbine combustion components have expanded the horizons for fuel nozzle development. Both new fluid designs and manufacturing technologies have led to the development of fuel nozzles that significantly reduce aircraft emissions. The goal of the ZCET program is to mesh the current technology of Lean Direct Injection and rocket injectors to provide quick mixing, low emissions, and high-performance fuel nozzle designs. An experimental program is planned to investigate the fuel nozzle concepts in a flametube test rig. Currently, a hydrogen system is being installed in cell 23 at NASA Glenn Research Center's Research Combustion Laboratory. Testing will be conducted on a variety of fuel nozzle concepts up to combustion pressures of 350 psia and inlet air temperatures of 1200 F. Computational fluid dynamics calculations, with the Glenn developed National Combustor Code, are being performed to optimize the fuel nozzle designs.

  14. A Micro Hydrogen Air Fuel Cell

    DTIC Science & Technology

    2005-10-01

    thin enough that it does not block the channels. This eliminated the step of having to sputter chrome /gold onto the wells and channels. Currently...to make the ink compatible with conventional thick film printing. In addition, the typical process for manufacturing electrode/membrane assemblies...catalytic activity of these inks, polarization curves for hydrogen oxidation were obtained using a pure hydrogen feed at one atmosphere pressure. With

  15. Electrolytes for Hydrocarbon Air Fuel Cells.

    DTIC Science & Technology

    1981-01-01

    performed on four commercially available electrolytes; namely, -methanedisulfonic acid - sulfoacetic acid -10-dl-camphorsulfonic acid -and...hydrocarbon chain can increase the stability of aliphatic sulfonic acids . Sulfoacetic and dl-10-camphorsulfonic acids were tested and found to decompose...thermally. 0 Sulfoacetic acid thermally decomposes at 180 C apparently due to decarboxylation. This is substantially below the 245 C reported by previous

  16. Electrolytes for Hydrocarbon Air Fuel Cells.

    DTIC Science & Technology

    1980-04-01

    available electrolytes; namely, -methanedisulfonic acid - sulfoacetic acid -10-dl-camphorsulfonic acid -and pentadecafluorooctanoic acid . These four...in the hydrocarbon chain can increase the stability of aliphatic sulfonic acids . Sulfoacetic and dl-10-camphorsulfonic acids were tested and found to...decompose thermally. 6 Sulfoacetic acid thermally decomposes at 180 C apparently due to decarboxylation. This is substantially 6 below the 245 C

  17. Analysis of pulsating spray flames propagating in lean two-phase mixtures with unity Lewis number

    SciTech Connect

    Nicoli, C.; Haldenwang, P.; Suard, S.

    2005-11-01

    Pulsating (or oscillatory) spray flames have recently been observed in experiments on two-phase combustion. Numerical studies have pointed out that such front oscillations can be obtained even with very simple models of homogeneous two-phase mixtures, including elementary vaporization schemes. The paper presents an analytical approach within the simple framework of the thermal-diffusive model, which is complemented by a vaporization rate independent of gas temperature, as soon as the latter reaches a certain thermal threshold ({theta}{sub v} in reduced form). The study involves the Damkoehler number (Da), the ratio of chemical reaction rate to vaporization rate, and the Zeldovich number (Ze) as essential parameters. We use the standard asymptotic method based on matched expansions in terms of 1/Ze. Linear analysis of two-phase flame stability is performed by studying, in the absence of differential diffusive effects (unity Lewis number), the linear growth rate of 2-D perturbations added to steady plane solutions and characterized by wavenumber k in the direction transverse to spreading. A domain of existence is found for the pulsating regime. It corresponds to mixture characteristics often met in air-fuel two-phase systems: low boiling temperature ({theta}{sub v} << 1), reaction rate not higher than vaporization rate (Da < 1, i.e., small droplets), and activation temperature assumed to be high compared with flame temperature (Ze {>=} 10). Satisfactory comparison with numerical simulations confirms the validity of the analytical approach; in particular, positive growth rates have been found for planar perturbations (k = 0) and for wrinkled fronts (k {ne} 0). Finally, comparison between predicted frequencies and experimental measurements is discussed.

  18. Some results on Gaussian mixtures

    NASA Astrophysics Data System (ADS)

    Felgueiras, Miguel; Santos, Rui; Martins, João Paulo

    2014-10-01

    We investigate Gaussian mixtures with independent components, whose parameters are numerically estimated. A decomposition of a Gaussian mixture is presented when the components have a common variance. We introduce a shifted and scaled t-Student distribution as an approximation for the distribution of Gaussian mixtures when their components have a common mean and develop a hypothesis test for testing the equality of the components means. Finally, we analyse the fitness of the approximate model to the logarithmic daily returns of the Portuguese stock index PSI-20.

  19. Power-Supply-Conditioning Circuit

    NASA Technical Reports Server (NTRS)

    Primas, L. E.; Loveland, R. C.

    1989-01-01

    Fluctuations of voltage suppressed in power supplies for precise radio-frequency circuits. Circuit suppresses both periodic and random deviations of dc supply voltage from desired steady level. Highly-stable feedback voltage regulator, conditioner intended in conjunction with conventional power-supply circuit to provide constant voltage to atomic frequency standard or other precise oscillator. Without conditioners, outputs of most commercial power supplies contain fluctuations causing unacceptably-large phase and amplitude modulation of precise oscillators.

  20. 2002 Industry Studies: Strategic Supply

    DTIC Science & Technology

    2002-01-01

    Strategic Supply is a unique industry study that focused not on a single industry, but rather on a process common to many industries known as Supply ... Chain Management (SCM). We found that the successful, global and innovative companies of today leverage their supply chains to achieve competitive and

  1. Food and water supply

    NASA Technical Reports Server (NTRS)

    Popov, I. G.

    1975-01-01

    Supplying astronauts with adequate food and water on short and long-term space flights is discussed based on experiences gained in space flight. Food consumption, energy requirements, and suitability of the foodstuffs for space flight are among the factors considered. Physicochemical and biological methods of food production and regeneration of water from astronaut metabolic wastes, as well as wastes produced in a closed ecological system, or as a result of technical processes taking place in various spacecraft systems are suggested for long-term space flights.

  2. Integrating the healthcare supply chain.

    PubMed

    Brennan, C D

    1998-01-01

    Today's integrated delivery systems (IDSs) require efficient supply chain processes to speed products to users at the lowest possible cost. Most excess costs within the supply chain are a result of inefficient and redundant processes involved in the transport and delivery of supplies from suppliers to healthcare providers. By integrating and assuming control of these supply chain processes, improving supply chain management practices, and organizing and implementing a disciplined redesign plan, IDSs can achieve substantial savings and better focus their organizations on their core patient care mission.

  3. Software for analysis of chemical mixtures--composition, occurrence, distribution, and possible toxicity

    USGS Publications Warehouse

    Scott, Jonathon C.; Skach, Kenneth A.; Toccalino, Patricia L.

    2013-01-01

    The composition, occurrence, distribution, and possible toxicity of chemical mixtures in the environment are research concerns of the U.S. Geological Survey and others. The presence of specific chemical mixtures may serve as indicators of natural phenomena or human-caused events. Chemical mixtures may also have ecological, industrial, geochemical, or toxicological effects. Chemical-mixture occurrences vary by analyte composition and concentration. Four related computer programs have been developed by the National Water-Quality Assessment Program of the U.S. Geological Survey for research of chemical-mixture compositions, occurrences, distributions, and possible toxicities. The compositions and occurrences are identified for the user-supplied data, and therefore the resultant counts are constrained by the user’s choices for the selection of chemicals, reporting limits for the analytical methods, spatial coverage, and time span for the data supplied. The distribution of chemical mixtures may be spatial, temporal, and (or) related to some other variable, such as chemical usage. Possible toxicities optionally are estimated from user-supplied benchmark data. The software for the analysis of chemical mixtures described in this report is designed to work with chemical-analysis data files retrieved from the U.S. Geological Survey National Water Information System but can also be used with appropriately formatted data from other sources. Installation and usage of the mixture software are documented. This mixture software was designed to function with minimal changes on a variety of computer-operating systems. To obtain the software described herein and other U.S. Geological Survey software, visit http://water.usgs.gov/software/.

  4. NNSA TRITIUM SUPPLY CHAIN

    SciTech Connect

    Wyrick, Steven; Cordaro, Joseph; Founds, Nanette; Chambellan, Curtis

    2013-08-21

    Savannah River Site plays a critical role in the Tritium Production Supply Chain for the National Nuclear Security Administration (NNSA). The entire process includes: • Production of Tritium Producing Burnable Absorber Rods (TPBARs) at the Westinghouse WesDyne Nuclear Fuels Plant in Columbia, South Carolina • Production of unobligated Low Enriched Uranium (LEU) at the United States Enrichment Corporation (USEC) in Portsmouth, Ohio • Irradiation of TPBARs with the LEU at the Tennessee Valley Authority (TVA) Watts Bar Reactor • Extraction of tritium from the irradiated TPBARs at the Tritium Extraction Facility (TEF) at Savannah River Site • Processing the tritium at the Savannah River Site, which includes removal of nonhydrogen species and separation of the hydrogen isotopes of protium, deuterium and tritium.

  5. Power Supply Unit

    NASA Technical Reports Server (NTRS)

    1982-01-01

    The Cuk DC to DC Switching Converter was developed by Caltech Professors, Slobodan Cuk and R. D. Middlebrook. The converter changes unsuitable dc voltage into one or more voltages suitable for powering electronic equipment; it can also be used in converting dc current to ac and vice versa. It was named one of the 100 most significant technical advances of 1979. The Cuk converter is more efficient than previous conversion devices, simpler, smaller, lighter, cheaper and highly reliable. The first application of the technology is in the Compucorp 685 word/data processor, manufactured by Compucorp. NASA waived title rights; Caltech granted exclusive license to the inventors, who in turn, transferred their rights to a company they founded called TESLA Company, which sublicenses the converter design and related technology to companies making power supplies for use in their own products.

  6. Stab water supply system

    SciTech Connect

    Hammett, D.S.

    1983-02-08

    Apparatus and method for fire suppression on offshore oil platforms including a stab receptacle on an outer surface of a platform connected to a fluid distribution system within the platform for distributing fire suppressing fluid to selected locations, a stab carrying a fluid conduit from a self-propelled service vessel, with the stab being in turn supported on a boom extending from the service vessel, a pumping system on the service vessel for supplying fire suppressing fluid through the conduit to the stab and thereby to the preselected locations. The service vessel is preferably a semi-submersible and includes a system for dynamic positioning of the vessel such as side thrusters in addition to a main propulsion unit.

  7. Switching power supply

    DOEpatents

    Mihalka, A.M.

    1984-06-05

    The invention is a repratable capacitor charging, switching power supply. A ferrite transformer steps up a dc input. The transformer primary is in a full bridge configuration utilizing power MOSFETs as the bridge switches. The transformer secondary is fed into a high voltage, full wave rectifier whose output is connected directly to the energy storage capacitor. The transformer is designed to provide adequate leakage inductance to limit capacitor current. The MOSFETs are switched to the variable frequency from 20 to 50 kHz to charge a capacitor from 0.6 kV. The peak current in a transformer primary and secondary is controlled by increasing the pulse width as the capacitor charges. A digital ripple counter counts pulses and after a preselected desired number is reached an up-counter is clocked.

  8. Sustainable Biomass Supply Systems

    SciTech Connect

    Erin Searcy; Dave Muth; Erin Wilkerson; Shahab Sokansanj; Bryan Jenkins; Peter Titman; Nathan Parker; Quinn Hart; Richard Nelson

    2009-04-01

    The U.S. Department of Energy (DOE) aims to displace 30% of the 2004 gasoline use (60 billion gal/yr) with biofuels by 2030 as outlined in the Energy Independence and Security Act of 2007, which will require 700 million tons of biomass to be sustainably delivered to biorefineries annually. Lignocellulosic biomass will make an important contribution towards meeting DOE’s ethanol production goals. For the biofuels industry to be an economically viable enterprise, the feedstock supply system (i.e., moving the biomass from the field to the refinery) cannot contribute more that 30% of the total cost of the biofuel production. The Idaho National Laboratory in collaboration with Oak Ridge National Laboratory, University of California, Davis and Kansas State University are developing a set of tools for identifying economical, sustainable feedstocks on a regional basis based on biorefinery siting.

  9. World petroleum supplies

    NASA Astrophysics Data System (ADS)

    Bell, Peter M.

    A number of conclusions by political conservatives about the fate of world petroleum supplies have been emerging lately. Among the most recent of them arose from discussions, held at the 1983 spring meeting of the American Association for the Advancement of Science (AAAS), which focused on the environment and resource study entitled “The Global 2000 Report” (New Scientist, June 9, 1983). Fred Singer, representing the Heritage Foundation of Washington, D.C., criticized the report, which predicted shortages in the near future, saying that the current world-wide oil glut will continue beyond the year 2000. Alternatives to the use of petroleum are a part of the cause. Singer argued that conservation, nuclear energy, and other petroleum substitutes will continue to suppress the demand for petroleum. In addition, according to other evaluations, exploration for petroleum and natural gas has not really begun.

  10. Simple power supply for power load controlled isoelectric focusing.

    PubMed

    Duša, Filip; Slais, Karel

    2014-04-01

    The power supply for IEF based on features of the Cockcroft-Walton voltage multiplier (CW VM) is described in this work. The article describes a design of the IEF power supply, its electric characteristics, and testing by IEF analysis. A circuit diagram of the power supply included two opposite charged branches (each consisting of four voltage doublers). The designed CW VM was powered by 230 V/50 Hz alternate current and it generated up to 5 kV and 90 mW at the output. Voltage and current characteristics of the power supply were measured by known load resistances in the range from 10 kΩ to 1 GΩ, which is a common resistance range for IEF strip geometry. Further, the power supply was tested by a separation of a model mixture of colored pI markers using a 175 × 3 × 0.5 mm focusing bed. Automatically limited power load enabled analysis of samples without previous optimization of the focusing voltage or electric current time courses according to sample composition. Moreover, the developed power supply did not produce any intrinsic heat and was easy to set up with cheap and commonly available parts.

  11. Oxygen supplies in disaster management.

    PubMed

    Blakeman, Thomas C; Branson, Richard D

    2013-01-01

    Mass casualty events and disasters, both natural and human-generated, occur frequently around the world and can generate scores of injured or ill victims in need of resources. Of the available medical supplies, oxygen remains the critical consumable resource in disaster management. Strategic management of oxygen supplies in disaster scenarios remains a priority. Hospitals have large supplies of liquid oxygen and a supply of compressed gas oxygen cylinders that allow several days of reserve, but a large influx of patients from a disaster can strain these resources. Most backup liquid oxygen supplies are attached to the main liquid system and supply line. In the event of damage to the main system, the reserve supply is rendered useless. The Strategic National Stockpile supplies medications, medical supplies, and equipment to disaster areas, but it does not supply oxygen. Contracted vendors can deliver oxygen to alternate care facilities in disaster areas, in the form of concentrators, compressed gas cylinders, and liquid oxygen. Planning for oxygen needs following a disaster still presents a substantial challenge, but alternate care facilities have proven to be valuable in relieving pressure from the mass influx of patients into hospitals, especially for those on home oxygen who require only an electrical source to power their oxygen concentrator.

  12. Mixture theory-based poroelasticity as a model of interstitial tissue growth.

    PubMed

    Cowin, Stephen C; Cardoso, Luis

    2012-01-01

    This contribution presents an alternative approach to mixture theory-based poroelasticity by transferring some poroelastic concepts developed by Maurice Biot to mixture theory. These concepts are a larger RVE and the subRVE-RVE velocity average tensor, which Biot called the micro-macro velocity average tensor. This velocity average tensor is assumed here to depend upon the pore structure fabric. The formulation of mixture theory presented is directed toward the modeling of interstitial growth, that is to say changing mass and changing density of an organism. Traditional mixture theory considers constituents to be open systems, but the entire mixture is a closed system. In this development the mixture is also considered to be an open system as an alternative method of modeling growth. Growth is slow and accelerations are neglected in the applications. The velocity of a solid constituent is employed as the main reference velocity in preference to the mean velocity concept from the original formulation of mixture theory. The standard development of statements of the conservation principles and entropy inequality employed in mixture theory are modified to account for these kinematic changes and to allow for supplies of mass, momentum and energy to each constituent and to the mixture as a whole. The objective is to establish a basis for the development of constitutive equations for growth of tissues.

  13. Developing sustainable food supply chains.

    PubMed

    Smith, B Gail

    2008-02-27

    This paper reviews the opportunities available for food businesses to encourage consumers to eat healthier and more nutritious diets, to invest in more sustainable manufacturing and distribution systems and to develop procurement systems based on more sustainable forms of agriculture. The important factors in developing more sustainable supply chains are identified as the type of supply chain involved and the individual business attitude to extending responsibility for product quality into social and environmental performance within their own supply chains. Interpersonal trust and working to standards are both important to build more sustainable local and many conserved food supply chains, but inadequate to transform mainstream agriculture and raw material supplies to the manufactured and commodity food markets. Cooperation among food manufacturers, retailers, NGOs, governmental and farmers' organizations is vital in order to raise standards for some supply chains and to enable farmers to adopt more sustainable agricultural practices.

  14. Bayesian Kernel Mixtures for Counts.

    PubMed

    Canale, Antonio; Dunson, David B

    2011-12-01

    Although Bayesian nonparametric mixture models for continuous data are well developed, there is a limited literature on related approaches for count data. A common strategy is to use a mixture of Poissons, which unfortunately is quite restrictive in not accounting for distributions having variance less than the mean. Other approaches include mixing multinomials, which requires finite support, and using a Dirichlet process prior with a Poisson base measure, which does not allow smooth deviations from the Poisson. As a broad class of alternative models, we propose to use nonparametric mixtures of rounded continuous kernels. An efficient Gibbs sampler is developed for posterior computation, and a simulation study is performed to assess performance. Focusing on the rounded Gaussian case, we generalize the modeling framework to account for multivariate count data, joint modeling with continuous and categorical variables, and other complications. The methods are illustrated through applications to a developmental toxicity study and marketing data. This article has supplementary material online.

  15. Reliability Estimates for Power Supplies

    SciTech Connect

    Lee C. Cadwallader; Peter I. Petersen

    2005-09-01

    Failure rates for large power supplies at a fusion facility are critical knowledge needed to estimate availability of the facility or to set priorties for repairs and spare components. A study of the "failure to operate on demand" and "failure to continue to operate" failure rates has been performed for the large power supplies at DIII-D, which provide power to the magnet coils, the neutral beam injectors, the electron cyclotron heating systems, and the fast wave systems. When one of the power supplies fails to operate, the research program has to be either temporarily changed or halted. If one of the power supplies for the toroidal or ohmic heating coils fails, the operations have to be suspended or the research is continued at de-rated parameters until a repair is completed. If one of the power supplies used in the auxiliary plasma heating systems fails the research is often temporarily changed until a repair is completed. The power supplies are operated remotely and repairs are only performed when the power supplies are off line, so that failure of a power supply does not cause any risk to personnel. The DIII-D Trouble Report database was used to determine the number of power supply faults (over 1,700 reports), and tokamak annual operations data supplied the number of shots, operating times, and power supply usage for the DIII-D operating campaigns between mid-1987 and 2004. Where possible, these power supply failure rates from DIII-D will be compared to similar work that has been performed for the Joint European Torus equipment. These independent data sets support validation of the fusion-specific failure rate values.

  16. Unrestricted Mixture Models for Class Identification in Growth Mixture Modeling

    ERIC Educational Resources Information Center

    Liu, Min; Hancock, Gregory R.

    2014-01-01

    Growth mixture modeling has gained much attention in applied and methodological social science research recently, but the selection of the number of latent classes for such models remains a challenging issue, especially when the assumption of proper model specification is violated. The current simulation study compared the performance of a linear…

  17. Dipole oscillations in fermionic mixtures

    SciTech Connect

    Chiacchiera, S.; Macri, T.; Trombettoni, A.

    2010-03-15

    We study dipole oscillations in a general fermionic mixture. Starting from the Boltzmann equation, we classify the different solutions in the parameter space through the number of real eigenvalues of the small oscillations matrix. We discuss how this number can be computed using the Sturm algorithm and its relation with the properties of the Laplace transform of the experimental quantities. After considering two components in harmonic potentials having different trapping frequencies, we study dipole oscillations in three-component mixtures. Explicit computations are done for realistic experimental setups using the classical Boltzmann equation without intraspecies interactions. A brief discussion of the application of this classification to general collective oscillations is also presented.

  18. Gaussian-mixture umbrella sampling

    PubMed Central

    van der Vaart, Arjan; Karplus, Martin

    2009-01-01

    We introduce the Gaussian-mixture umbrella sampling method (GAMUS), a biased molecular dynamics technique based on adaptive umbrella sampling that efficiently escapes free energy minima in multi-dimensional problems. The prior simulation data are reweighted with a maximum likelihood formulation, and the new approximate probability density is fit to a Gaussian-mixture model, augmented by information about the unsampled areas. The method can be used to identify free energy minima in multi-dimensional reaction coordinates. To illustrate GAMUS, we apply it to the alanine dipeptide (2D reaction coordinate) and tripeptide (4D reaction coordinate). PMID:19284746

  19. 14 CFR 23.1147 - Mixture controls.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Mixture controls. 23.1147 Section 23.1147... Accessories § 23.1147 Mixture controls. (a) If there are mixture controls, each engine must have a separate control, and each mixture control must have guards or must be shaped or arranged to prevent confusion...

  20. 14 CFR 23.1147 - Mixture controls.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Mixture controls. 23.1147 Section 23.1147... Accessories § 23.1147 Mixture controls. (a) If there are mixture controls, each engine must have a separate control, and each mixture control must have guards or must be shaped or arranged to prevent confusion...

  1. 16 CFR 1500.5 - Hazardous mixtures.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Hazardous mixtures. 1500.5 Section 1500.5... HAZARDOUS SUBSTANCES AND ARTICLES; ADMINISTRATION AND ENFORCEMENT REGULATIONS § 1500.5 Hazardous mixtures. For a mixture of substances, the determination of whether the mixture is a “hazardous substance”...

  2. 16 CFR 1500.5 - Hazardous mixtures.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 16 Commercial Practices 2 2011-01-01 2011-01-01 false Hazardous mixtures. 1500.5 Section 1500.5... HAZARDOUS SUBSTANCES AND ARTICLES; ADMINISTRATION AND ENFORCEMENT REGULATIONS § 1500.5 Hazardous mixtures. For a mixture of substances, the determination of whether the mixture is a “hazardous substance”...

  3. 16 CFR 1500.5 - Hazardous mixtures.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 16 Commercial Practices 2 2014-01-01 2014-01-01 false Hazardous mixtures. 1500.5 Section 1500.5... HAZARDOUS SUBSTANCES AND ARTICLES; ADMINISTRATION AND ENFORCEMENT REGULATIONS § 1500.5 Hazardous mixtures. For a mixture of substances, the determination of whether the mixture is a “hazardous substance”...

  4. 16 CFR 1500.5 - Hazardous mixtures.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 16 Commercial Practices 2 2013-01-01 2013-01-01 false Hazardous mixtures. 1500.5 Section 1500.5... HAZARDOUS SUBSTANCES AND ARTICLES; ADMINISTRATION AND ENFORCEMENT REGULATIONS § 1500.5 Hazardous mixtures. For a mixture of substances, the determination of whether the mixture is a “hazardous substance”...

  5. 14 CFR 23.1147 - Mixture controls.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Mixture controls. 23.1147 Section 23.1147... Accessories § 23.1147 Mixture controls. (a) If there are mixture controls, each engine must have a separate control, and each mixture control must have guards or must be shaped or arranged to prevent confusion...

  6. 16 CFR 1500.5 - Hazardous mixtures.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Hazardous mixtures. 1500.5 Section 1500.5... HAZARDOUS SUBSTANCES AND ARTICLES; ADMINISTRATION AND ENFORCEMENT REGULATIONS § 1500.5 Hazardous mixtures. For a mixture of substances, the determination of whether the mixture is a “hazardous substance”...

  7. 14 CFR 23.1147 - Mixture controls.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Mixture controls. 23.1147 Section 23.1147... Accessories § 23.1147 Mixture controls. (a) If there are mixture controls, each engine must have a separate control, and each mixture control must have guards or must be shaped or arranged to prevent confusion...

  8. 14 CFR 23.1147 - Mixture controls.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Mixture controls. 23.1147 Section 23.1147... Accessories § 23.1147 Mixture controls. (a) If there are mixture controls, each engine must have a separate control, and each mixture control must have guards or must be shaped or arranged to prevent confusion...

  9. Cholangiocytes and blood supply

    PubMed Central

    Gaudio, Eugenio; Franchitto, Antonio; Pannarale, Luigi; Carpino, Guido; Alpini, Gianfranco; Francis, Heather; Glaser, Shannon; Alvaro, Domenico; Onori, Paolo

    2006-01-01

    The microvascular supply of the biliary tree, the peribiliary plexus (PBP), stems from the hepatic artery branches and flows into the hepatic sinusoids. A detailed three-dimensional study of the PBP has been performed by using the Scanning Electron Microscopy vascular corrosion casts (SEMvcc) technique. Considering that the PBP plays a fundamental role in supporting the secretory and absorptive functions of the biliary epithelium, their organization in either normalcy and pathology is explored. The normal liver shows the PBP arranged around extra- and intrahepatic biliary tree. In the small portal tract PBP was characterized by a single layer of capillaries which progressively continued with the extrahepatic PBP where it showed a more complex vascular network. After common duct ligation (BDL), progressive modifications of bile duct and PBP proliferation are observed. The PBP presents a three-dimensional network arranged around many bile ducts and appears as bundles of vessels, composed by capillaries of homogeneous diameter with a typical round mesh structure. The PBP network is easily distinguishable from the sinusoidal network which appears normal. Considering the enormous extension of the PBP during BDL, the possible role played by the Vascular Endothelial Growth Factor (VEGF) is evaluated. VEGF-A, VEGF-C and their related receptors appeared highly immunopositive in proliferating cholangiocytes of BDL rats. The administration of anti-VEGF-A or anti-VEGF-C antibodies to BDL rats as well as hepatic artery ligation induced a reduced bile duct mass. The administration of rVEGF-A to BDL hepatic artery ligated rats prevented the decrease of cholangiocyte proliferation and VEGF-A expression as compared to BDL control rats. These data suggest the role of arterial blood supply of the biliary tree in conditions of cholangiocyte proliferation, such as it occurs during chronic cholestasis. On the other hand, the role played by VEGF as a tool of cross-talk between

  10. High-temperature oxidation of Zircaloy in hydrogen-steam mixtures. [PWR; BWR

    SciTech Connect

    Chung, H.M.; Thomas, G.R.

    1982-09-01

    Oxidation rates of Zircaloy-4 cladding tubes have been measured in hydrogen-steam mixtures at 1200 to 1700/sup 0/C. For a given isothermal oxidation temperature, the oxide layer thicknesses have been measured as a function of time, steam supply rate, and hydrogen overpressure. The oxidation rates in the mixtures were compared with similar data obtained in pure steam and helium-steam environments under otherwise identical conditions. The rates in pure steam and helium-steam mixtures were equivalent and comparable to the parabolic rates obtained under steam-saturated conditions and reported in the literature. However, when the helium was replaced with hydrogen of equivalent partial pressure, a significantly smaller oxidation rate was observed. For high steam-supply rates, the oxidation kinetics in a hydrogen-steam mixture were parabolic, but the rate was smaller than for pure steam or helium-steam mixtures. Under otherwise identical conditions, the ratio of the parabolic rate for hydrogen-steam to that for pure steam decreased with increasing temperature and decreasing steam-supply rate.

  11. Taylor dispersion analysis of mixtures.

    PubMed

    Cottet, Hervé; Biron, Jean-Philippe; Martin, Michel

    2007-12-01

    Taylor dispersion analysis (TDA) is a fast and simple method for determining hydrodynamic radii. In the case of sample mixtures, TDA, as the other nonseparative methods, leads to an average diffusion coefficient on the different molecules constituting the mixture. We set in this work the equations giving, on a consistent basis, the average values obtained by TDA with detectors with linear response functions. These equations confronted TDA experiments of sample mixtures containing different proportions of a small molecule and a polymer standard. Very good agreement between theory and experiment was obtained. In a second part of this work, on the basis of monomodal or bimodal molar mass distributions of polymers, the different average diffusion coefficients corresponding to TDA were compared to the z-average diffusion coefficient (D(z)) obtained from dynamic light scattering (DLS) experiments and to the weight average diffusion coefficient (D(w)). This latter value is sometimes considered as the most representative of the sample mixture. From these results, it appears that, for monomodal distribution and relatively low polydispersity (I = 1.15), the average diffusion coefficient generally derived from TDA is very close to Dw. However, for highly polydisperse samples (e.g., bimodal polydisperse distributions), important differences could be obtained (up to 35% between TDA and D(w)). In all the cases, the average diffusion coefficient obtained by TDA for a mass concentration detector was closer to the Dw value than the z-average obtained by DLS.

  12. Electrochemical signatures of multivitamin mixtures.

    PubMed

    Mohan, A M Vinu; Brunetti, Barbara; Bulbarello, Andrea; Wang, Joseph

    2015-11-21

    The ability of cyclic square wave voltammetry to identify distinct fingerprints of multiple vitamins, in a single voltammetric run, is demonstrated. This method represents an efficient alternative to more common techniques for fast screening of complex vitamin mixtures or commercial tablets due to its low cost, high speed and sensitivity.

  13. Genetic Analysis of Plant Mixtures

    PubMed Central

    Griffing, B.

    1989-01-01

    Plant mixtures are difficult to analyze genetically because of possible interactions between neighboring plants (i.e., between plants in the same biological group). However, a genetic modeling scheme has been devised which, theoretically, can accommodate such interactions. This study was an attempt to put the theoretical modeling procedure to an experimental test. To this end an experimental procedure was devised that generated biological groups from a well defined base population. A cultural system was used which permitted growing plant mixtures in controlled environmental facilities. This allowed the experiment to be conducted over a wide range of temperature and nutrient conditions. Application of the theoretical gene model to the experimental data permitted identification of those classes of gene effects that were responsible for genetic variation exhibited by the mixtures. Adequacy of the genetic modeling description was corroborated by precise prediction of an independent genetic response. The genetic analyses also identified statistically significant temperature-and nutrient-dependent forms of heterosis. It was concluded that the study demonstrated the suitability of the theoretical group gene model for describing complexities inherent in plant mixtures. PMID:17246509

  14. Uphill diffusion in multicomponent mixtures.

    PubMed

    Krishna, Rajamani

    2015-05-21

    Molecular diffusion is an omnipresent phenomena that is important in a wide variety of contexts in chemical, physical, and biological processes. In the majority of cases, the diffusion process can be adequately described by Fick's law that postulates a linear relationship between the flux of any species and its own concentration gradient. Most commonly, a component diffuses down the concentration gradient. The major objective of this review is to highlight a very wide variety of situations that cause the uphill transport of one constituent in the mixture. Uphill diffusion may occur in multicomponent mixtures in which the diffusion flux of any species is strongly coupled to that of its partner species. Such coupling effects often arise from strong thermodynamic non-idealities. For a quantitative description we need to use chemical potential gradients as driving forces. The transport of ionic species in aqueous solutions is coupled with its partner ions because of the electro-neutrality constraints; such constraints may accelerate or decelerate a specific ion. When uphill diffusion occurs, we observe transient overshoots during equilibration; the equilibration process follows serpentine trajectories in composition space. For mixtures of liquids, alloys, ceramics and glasses the serpentine trajectories could cause entry into meta-stable composition zones; such entry could result in phenomena such as spinodal decomposition, spontaneous emulsification, and the Ouzo effect. For distillation of multicomponent mixtures that form azeotropes, uphill diffusion may allow crossing of distillation boundaries that are normally forbidden. For mixture separations with microporous adsorbents, uphill diffusion can cause supra-equilibrium loadings to be achieved during transient uptake within crystals; this allows the possibility of over-riding adsorption equilibrium for achieving difficult separations.

  15. Building an efficient supply chain.

    PubMed

    Scalise, Dagmara

    2005-08-01

    Realizing at last that supply chain management can produce efficiencies and save costs, hospitals are beginning to adopt practices from other industries, such as the concept of extended supply chains, to improve product flow. They're also investing in enterprise planning resource software, radio frequency identification and other technologies, using quality data to drive standardization and streamlining processes.

  16. Petroleum supply monthly, August 1993

    SciTech Connect

    Not Available

    1993-09-01

    This publication the Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report, (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. Data presented are divided into Summary Statistics and Detailed Statistics.

  17. Optimisation of a green gas supply chain--a review.

    PubMed

    Bekkering, J; Broekhuis, A A; van Gemert, W J T

    2010-01-01

    In this review the knowledge status of and future research options on a green gas supply based on biogas production by co-digestion is explored. Applications and developments of the (bio)gas supply in The Netherlands have been considered, whereafter literature research has been done into the several stages from production of dairy cattle manure and biomass to green gas injection into the gas grid. An overview of a green gas supply chain has not been made before. In this study it is concluded that on installation level (micro-level) much practical knowledge is available and on macro-level knowledge about availability of biomass. But on meso-level (operations level of a green gas supply) very little research has been done until now. Future research should include the modeling of a green gas supply chain on an operations level, i.e. questions must be answered as where to build digesters based on availability of biomass. Such a model should also advise on technology of upgrading depending on scale factors. Future research might also give insight in the usability of mixing (partly upgraded) biogas with natural gas. The preconditions for mixing would depend on composition of the gas, the ratio of gases to be mixed and the requirements on the mixture.

  18. Effects of dietary supplementation of a purified nucleotide mixture on growth, immune function, and disease and stress resistance in channel catfish, Ictalurus punctatus

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Juvenile channel catfish (14.4 g average initial weight) were fed diets supplemented with a purified nucleotide mixture for 8 weeks. The mixture consisted of five nucleotides supplied on an equal basis as disodium salts at combined concentrations of 0 (control), 0.1, 0.3, 0.9, or 2.7% of diet. At th...

  19. Effects of dietary supplementation of a purified nucleotide mixture on immune function and disease and stress resistance in channel catfish, Ictalurus punctatus

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Juvenile channel catfish (14.4 g average initial weight) were fed diets supplemented with a purified nucleotide mixture for 8 weeks. The mixture consisted of five nucleotides supplied on an equal basis as disodium salts at combined concentrations of 0 (control), 0.1, 0.3, 0.9, or 2.7% of diet. At th...

  20. The Anaesthesia Gas Supply System

    PubMed Central

    Das, Sabyasachi; Chattopadhyay, Subhrajyoti; Bose, Payel

    2013-01-01

    The anaesthesia gas supply system is designed to provide a safe, cost-effective and convenient system for the delivery of medical gases at the point of-use. The doctrine of the anaesthesia gas supply system is based on four essential principles: Identity, continuity, adequacy and quality. Knowledge about gas supply system is an integral component of safe anaesthetic practice. Mishaps involving the malfunction or misuse of medical gas supply to operating theatres have cost many lives. The medical gases used in anaesthesia and intensive care are oxygen, nitrous oxide, medical air, entonox, carbon dioxide and heliox. Oxygen is one of the most widely used gases for life-support and respiratory therapy besides anaesthetic procedures. In this article, an effort is made to describe the production, storage and delivery of anaesthetic gases. The design of anaesthesia equipment must take into account the local conditions such as climate, demand and power supply. The operational policy of the gas supply system should have a backup plan to cater to the emergency need of the hospital, in the event of the loss of the primary source of supply. PMID:24249882

  1. Wetland and water supply

    USGS Publications Warehouse

    Baker, John Augustus

    1960-01-01

    The Geological Survey has received numerous inquiries about the effects of proposed changes in the wetland environment. The nature of the inquiries suggests a general confusion in the public mind as to wetland values and an increasing concern by the public with the need for facts as a basis for sound decisions when public action is required. Perhaps the largest gap in our knowledge is in regard to the role played by the wetland in the natural water scheme. Specialists in such fields as agriculture and conservation have studied the wetland in relation to its special uses and values for farming and as a habitat for fish and wildlife. However, except as studied incidentally by these specialists, the role of the wetland with respect to water has been largely neglected. This facet of the wetland problem is of direct concern to the Geological Survey. We commonly speak of water in terms of its place in the hydrologic environment---as, for example, surface water or ground water. These terms imply that water can be neatly pigeonholed. With respect to the wetland environment nothing can be further from the truth. In fact, one objective of this discussion is to demonstrate that for the wetland environment surface water, ground water, and soil water cannot be separated realistically, but are closely interrelated and must be studied together. It should be noted that this statement holds true for the hydrologic environment in general, and that the wetland environment is by no means unique in this respect. Our second and principal objective is to identify some of the problems that must be studied in order to clarify the role of the wetland in relation to water supply. We have chosen to approach these objectives by briefly describing one area for which we have some information, and by using this example to point out some of the problems that need study. First, however, let us define what we, as geohydrologists, mean by wetland and briefly consider wetland classifications. For our

  2. Water supply and demand in an energy supply model

    SciTech Connect

    Abbey, D; Loose, V

    1980-12-01

    This report describes a tool for water and energy-related policy analysis, the development of a water supply and demand sector in a linear programming model of energy supply in the United States. The model allows adjustments in the input mix and plant siting in response to water scarcity. Thus, on the demand side energy conversion facilities can substitute more costly dry cooling systems for conventional evaporative systems. On the supply side groundwater and water purchased from irrigators are available as more costly alternatives to unappropriated surface water. Water supply data is developed for 30 regions in 10 Western states. Preliminary results for a 1990 energy demand scenario suggest that, at this level of spatial analysis, water availability plays a minor role in plant siting. Future policy applications of the modeling system are discussed including the evaluation of alternative patterns of synthetic fuels development.

  3. Generalized Beta Mixtures of Gaussians.

    PubMed

    Armagan, Artin; Dunson, David B; Clyde, Merlise

    2011-01-01

    In recent years, a rich variety of shrinkage priors have been proposed that have great promise in addressing massive regression problems. In general, these new priors can be expressed as scale mixtures of normals, but have more complex forms and better properties than traditional Cauchy and double exponential priors. We first propose a new class of normal scale mixtures through a novel generalized beta distribution that encompasses many interesting priors as special cases. This encompassing framework should prove useful in comparing competing priors, considering properties and revealing close connections. We then develop a class of variational Bayes approximations through the new hierarchy presented that will scale more efficiently to the types of truly massive data sets that are now encountered routinely.

  4. MULTIVARIATE KERNEL PARTITION PROCESS MIXTURES

    PubMed Central

    Dunson, David B.

    2013-01-01

    Mixtures provide a useful approach for relaxing parametric assumptions. Discrete mixture models induce clusters, typically with the same cluster allocation for each parameter in multivariate cases. As a more flexible approach that facilitates sparse nonparametric modeling of multivariate random effects distributions, this article proposes a kernel partition process (KPP) in which the cluster allocation varies for different parameters. The KPP is shown to be the driving measure for a multivariate ordered Chinese restaurant process that induces a highly-flexible dependence structure in local clustering. This structure allows the relative locations of the random effects to inform the clustering process, with spatially-proximal random effects likely to be assigned the same cluster index. An exact block Gibbs sampler is developed for posterior computation, avoiding truncation of the infinite measure. The methods are applied to hormone curve data, and a dependent KPP is proposed for classification from functional predictors. PMID:24478563

  5. Petroleum supply monthly, February 1994

    SciTech Connect

    Not Available

    1994-03-01

    The Petroleum Supply Monthly presents data describing the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders; operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. Data are divided into two sections: Summary statistics and Detailed statistics.

  6. Petroleum supply monthly, April 1994

    SciTech Connect

    Not Available

    1994-04-01

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographical regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US.

  7. Oil and Gas Supply Modeling

    NASA Astrophysics Data System (ADS)

    Gass, S. I.

    1982-05-01

    The theoretical and applied state of the art of oil and gas supply models was discussed. The following areas were addressed: the realities of oil and gas supply, prediction of oil and gas production, problems in oil and gas modeling, resource appraisal procedures, forecasting field size and production, investment and production strategies, estimating cost and production schedules for undiscovered fields, production regulations, resource data, sensitivity analysis of forecasts, econometric analysis of resource depletion, oil and gas finding rates, and various models of oil and gas supply.

  8. The 3He Supply Problem

    SciTech Connect

    Kouzes, Richard T.

    2009-05-01

    One of the main uses for 3He is in gas proportional counters for neutron detection. Radiation portal monitors deployed for homeland security and non-proliferation use such detectors. Other uses of 3He are for research detectors, commercial instruments, well logging detectors, dilution refrigerators, for targets or cooling in nuclear research, and for basic research in condensed matter physics. The US supply of 3He comes almost entirely from the decay of tritium used in nuclear weapons by the US and Russia. A few other countries contribute a small amount to the world’s 3He supply. Due to the large increase in use of 3He for homeland security, the supply has dwindled, and can no longer meet the demand. This white paper reviews the problems of supply, utilization, and alternatives.

  9. Model Misspecification: Finite Mixture or Homogeneous?

    PubMed Central

    Tarpey, Thaddeus; Yun, Dong; Petkova, Eva

    2007-01-01

    A common problem in statistical modelling is to distinguish between finite mixture distribution and a homogeneous non-mixture distribution. Finite mixture models are widely used in practice and often mixtures of normal densities are indistinguishable from homogenous non-normal densities. This paper illustrates what happens when the EM algorithm for normal mixtures is applied to a distribution that is a homogeneous non-mixture distribution. In particular, a population-based EM algorithm for finite mixtures is introduced and applied directly to density functions instead of sample data. The population-based EM algorithm is used to find finite mixture approximations to common homogeneous distributions. An example regarding the nature of a placebo response in drug treated depressed subjects is used to illustrate ideas. PMID:18974843

  10. Variable mixture ratio performance through nitrogen augmentation

    NASA Technical Reports Server (NTRS)

    Beichel, R.; Obrien, C. J.; Bair, E. K.

    1988-01-01

    High/variable mixture ratio O2/H2 candidate engine cycles are examined for earth-to-orbit vehicle application. Engine performance and power balance information are presented for the candidate cycles relative to chamber pressure, bulk density, and mixture ratio. Included in the cycle screening are concepts where a third fluid (liquid nitrogen) is used to achieve a variable mixture ratio over the trajectory from liftoff to earth orbit. The third fluid cycles offer a very low risk, fully reusable, low operation cost alternative to high/variable mixture ratio bipropellant cycles. Variable mixture ratio engines with extendible nozzle are slightly lower performing than a single mixture ratio engine (MR = 7:1) with extendible nozzle. Dual expander engines (MR = 7:1) have slightly better performance than the single mixture ratio engine. Dual fuel dual expander engines offer a 16 percent improvement over the single mixture ratio engine.

  11. TRANSISTOR HIGH VOLTAGE POWER SUPPLY

    DOEpatents

    Driver, G.E.

    1958-07-15

    High voltage, direct current power supplies are described for use with battery powered nuclear detection equipment. The particular advantages of the power supply described, are increased efficiency and reduced size and welght brought about by the use of transistors in the circuit. An important feature resides tn the employment of a pair of transistors in an alternatefiring oscillator circuit having a coupling transformer and other circuit components which are used for interconnecting the various electrodes of the transistors.

  12. Reinforcement learning in supply chains.

    PubMed

    Valluri, Annapurna; North, Michael J; Macal, Charles M

    2009-10-01

    Effective management of supply chains creates value and can strategically position companies. In practice, human beings have been found to be both surprisingly successful and disappointingly inept at managing supply chains. The related fields of cognitive psychology and artificial intelligence have postulated a variety of potential mechanisms to explain this behavior. One of the leading candidates is reinforcement learning. This paper applies agent-based modeling to investigate the comparative behavioral consequences of three simple reinforcement learning algorithms in a multi-stage supply chain. For the first time, our findings show that the specific algorithm that is employed can have dramatic effects on the results obtained. Reinforcement learning is found to be valuable in multi-stage supply chains with several learning agents, as independent agents can learn to coordinate their behavior. However, learning in multi-stage supply chains using these postulated approaches from cognitive psychology and artificial intelligence take extremely long time periods to achieve stability which raises questions about their ability to explain behavior in real supply chains. The fact that it takes thousands of periods for agents to learn in this simple multi-agent setting provides new evidence that real world decision makers are unlikely to be using strict reinforcement learning in practice.

  13. Petroleum supply monthly, April 1990

    SciTech Connect

    1990-06-26

    The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in the Petroleum Supply Monthly describe (PSM) the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply.'' Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: (1) the Summary Statistics and (2) the Detailed Statistics.

  14. 21 CFR 82.6 - Certifiable mixtures.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... and, in the case of mixtures which are aqueous solutions or aqueous pastes, sodium benzoate in a... 21 Food and Drugs 1 2011-04-01 2011-04-01 false Certifiable mixtures. 82.6 Section 82.6 Food and... PROVISIONALLY LISTED COLORS AND SPECIFICATIONS General Provisions § 82.6 Certifiable mixtures. (a) A batch of...

  15. 21 CFR 82.6 - Certifiable mixtures.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... and, in the case of mixtures which are aqueous solutions or aqueous pastes, sodium benzoate in a... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Certifiable mixtures. 82.6 Section 82.6 Food and... PROVISIONALLY LISTED COLORS AND SPECIFICATIONS General Provisions § 82.6 Certifiable mixtures. (a) A batch of...

  16. 14 CFR 25.1147 - Mixture controls.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Mixture controls. 25.1147 Section 25.1147... STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Powerplant Controls and Accessories § 25.1147 Mixture controls. (a) If there are mixture controls, each engine must have a separate control. The controls must...

  17. 14 CFR 25.1147 - Mixture controls.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Mixture controls. 25.1147 Section 25.1147... STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Powerplant Controls and Accessories § 25.1147 Mixture controls. (a) If there are mixture controls, each engine must have a separate control. The controls must...

  18. 14 CFR 27.1147 - Mixture controls.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Mixture controls. 27.1147 Section 27.1147... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Powerplant Controls and Accessories § 27.1147 Mixture controls. If there are mixture controls, each engine must have a separate control and the controls must...

  19. 40 CFR 721.9540 - Polysulfide mixture.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Polysulfide mixture. 721.9540 Section... Substances § 721.9540 Polysulfide mixture. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as a polysulfide mixture (PMN P-93-1043)...

  20. 40 CFR 721.9540 - Polysulfide mixture.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Polysulfide mixture. 721.9540 Section... Substances § 721.9540 Polysulfide mixture. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as a polysulfide mixture (PMN P-93-1043)...

  1. 14 CFR 29.1147 - Mixture controls.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Mixture controls. 29.1147 Section 29.1147... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Powerplant Controls and Accessories § 29.1147 Mixture controls. (a) If there are mixture controls, each engine must have a separate control, and the...

  2. 14 CFR 29.1147 - Mixture controls.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Mixture controls. 29.1147 Section 29.1147... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Powerplant Controls and Accessories § 29.1147 Mixture controls. (a) If there are mixture controls, each engine must have a separate control, and the...

  3. 14 CFR 27.1147 - Mixture controls.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Mixture controls. 27.1147 Section 27.1147... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Powerplant Controls and Accessories § 27.1147 Mixture controls. If there are mixture controls, each engine must have a separate control and the controls must...

  4. 40 CFR 721.9540 - Polysulfide mixture.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Polysulfide mixture. 721.9540 Section... Substances § 721.9540 Polysulfide mixture. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as a polysulfide mixture (PMN P-93-1043)...

  5. 14 CFR 25.1147 - Mixture controls.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Mixture controls. 25.1147 Section 25.1147... STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Powerplant Controls and Accessories § 25.1147 Mixture controls. (a) If there are mixture controls, each engine must have a separate control. The controls must...

  6. 40 CFR 721.9540 - Polysulfide mixture.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Polysulfide mixture. 721.9540 Section... Substances § 721.9540 Polysulfide mixture. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as a polysulfide mixture (PMN P-93-1043)...

  7. 14 CFR 25.1147 - Mixture controls.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Mixture controls. 25.1147 Section 25.1147... STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Powerplant Controls and Accessories § 25.1147 Mixture controls. (a) If there are mixture controls, each engine must have a separate control. The controls must...

  8. 14 CFR 27.1147 - Mixture controls.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Mixture controls. 27.1147 Section 27.1147... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Powerplant Controls and Accessories § 27.1147 Mixture controls. If there are mixture controls, each engine must have a separate control and the controls must...

  9. 40 CFR 721.9540 - Polysulfide mixture.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Polysulfide mixture. 721.9540 Section... Substances § 721.9540 Polysulfide mixture. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as a polysulfide mixture (PMN P-93-1043)...

  10. 14 CFR 29.1147 - Mixture controls.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Mixture controls. 29.1147 Section 29.1147... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Powerplant Controls and Accessories § 29.1147 Mixture controls. (a) If there are mixture controls, each engine must have a separate control, and the...

  11. 21 CFR 82.6 - Certifiable mixtures.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 1 2013-04-01 2013-04-01 false Certifiable mixtures. 82.6 Section 82.6 Food and... PROVISIONALLY LISTED COLORS AND SPECIFICATIONS General Provisions § 82.6 Certifiable mixtures. (a) A batch of a mixture which contains no straight color listed in subpart C or D may be certified for use in food,...

  12. 21 CFR 82.6 - Certifiable mixtures.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 1 2012-04-01 2012-04-01 false Certifiable mixtures. 82.6 Section 82.6 Food and... PROVISIONALLY LISTED COLORS AND SPECIFICATIONS General Provisions § 82.6 Certifiable mixtures. (a) A batch of a mixture which contains no straight color listed in subpart C or D may be certified for use in food,...

  13. 14 CFR 27.1147 - Mixture controls.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Mixture controls. 27.1147 Section 27.1147... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Powerplant Controls and Accessories § 27.1147 Mixture controls. If there are mixture controls, each engine must have a separate control and the controls must...

  14. 14 CFR 29.1147 - Mixture controls.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Mixture controls. 29.1147 Section 29.1147... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Powerplant Controls and Accessories § 29.1147 Mixture controls. (a) If there are mixture controls, each engine must have a separate control, and the...

  15. 14 CFR 25.1147 - Mixture controls.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Mixture controls. 25.1147 Section 25.1147... STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Powerplant Controls and Accessories § 25.1147 Mixture controls. (a) If there are mixture controls, each engine must have a separate control. The controls must...

  16. 14 CFR 29.1147 - Mixture controls.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Mixture controls. 29.1147 Section 29.1147... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Powerplant Controls and Accessories § 29.1147 Mixture controls. (a) If there are mixture controls, each engine must have a separate control, and the...

  17. 14 CFR 27.1147 - Mixture controls.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Mixture controls. 27.1147 Section 27.1147... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Powerplant Controls and Accessories § 27.1147 Mixture controls. If there are mixture controls, each engine must have a separate control and the controls must...

  18. 21 CFR 82.6 - Certifiable mixtures.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 1 2014-04-01 2014-04-01 false Certifiable mixtures. 82.6 Section 82.6 Food and... PROVISIONALLY LISTED COLORS AND SPECIFICATIONS General Provisions § 82.6 Certifiable mixtures. (a) A batch of a mixture which contains no straight color listed in subpart C or D may be certified for use in food,...

  19. Space Station nitrogen supply system based on stored chemicals

    NASA Technical Reports Server (NTRS)

    Powell, F. T.; Schwartz, M.

    1985-01-01

    The Space Station atmosphere is to have an 'earth-like' composition, and nitrogen is to be routinely supplied to replace losses. The required nitrogen is to be provided by an innovative method, involving a catalytic dissociation of liquid N2H4 and separation of the product nitrogen and hydrogen mixture. The considered technique of nitrogen storage and resupply has several advantages in comparison to methods using either cryogenic liquid or high pressure nitrogen. One advantage is related to savings with respect to launch weight, while a second advantage is provided by the obtained hydrogen which is available for other uses within the Space Station.

  20. Generating mixtures of spatial qubits

    NASA Astrophysics Data System (ADS)

    Lima, G.; Torres-Ruiz, F. A.; Neves, Leonardo; Delgado, A.; Saavedra, C.; Pádua, S.

    2008-10-01

    In a recent letter [L. Neves, G. Lima, J.G. Aguirre Gómez, C.H. Monken, C. Saavedra, S. Pádua, Phys. Rev. Lett. 94 (2005) 100501], we presented a scheme for generating pure entangled states of spatial qudits ( D-dimensional quantum systems) by using the momentum transverse correlation of the parametric down-converted photons. In this work, we discuss a generalization of this process to enable the creation of mixed states. With the technique proposed we experimentally generated a mixture of two spatial qubits.

  1. [Trace element supply to ruminants in the German Democratic Republic. 2. Supply of copper].

    PubMed

    Anke, M; Groppel, B; Lüdke, H; Grün, M; Kleemann, J

    1975-06-01

    The supply of copper to ruminants as influenced by and depending on the geological origin of soils was investigated in different parts of the GDR by using the hair test. Red clovers (meadow clover and field clover) were used as indicator plants. The following results were obtained: Data on the Cu content of clovers grown on soils of the same geological origin were found to correlate with r = 0,81. After eliminating the effects of Cu antagonists resulting from industrial pollution it was possible to establish numerical relations (B = 0.39 and B = 0.89) between the relative values (specific for the particular location) for the Cu content of the indicator plants and the percentage of cows suffering from Cu deficiencies (6.0 and 5.0 ppm Cu in hair). The lowest percentages of Cu supply to the ruminants (established on the basis of the Cu content of red clovers) were found on diluvial sandy soils, glacial loams and peat and bog soils whereas the highest percentages of Cu were found on weathered soils (of phyllite, gneiss, shell limestone, red marl soils and porphyry). Secondary Cu deficiencies in ruminants may arise, independent of the geological origin of the soil material, in places exposed to the main direction of the winds from major industrial areas (emission of SO2, Cd and Mo). Due to primary and/or secondary deficiencies the supply of Cu to ruminants in various locations (syenite, granite, red sandstone, gneiss, loess; peat soils, diluvial sandy soils) may be insufficient. A detailed description is given of areas where Cu deficiency is likely to occur and recommendations are given on how to use mineral mixtures containing a high proportion of Cu (1.00 g Cu per kg).

  2. Aligning incentives in supply chains.

    PubMed

    Narayanan, V G; Raman, Ananth

    2004-11-01

    Most companies don't worry about the behavior of their supply chain partners. Instead, they expect the supply chain to work efficiently without interference, as if guided by Adam Smith's famed invisible hand. In their study of more than 50 supply networks, V.G. Narayanan and Ananth Raman found that companies often looked out for their own interests and ignored those of their network partners. Consequently, supply chains performed poorly. Those results aren't shocking when you consider that supply chains extend across several functions and many companies, each with its own priorities and goals. Yet all those functions and firms must pull in the same direction for a chain to deliver goods and services to consumers quickly and cost-effectively. According to the authors, a supply chain works well only if the risks, costs, and rewards of doing business are distributed fairly across the network. In fact, misaligned incentives are often the cause of excess inventory, stock-outs, incorrect forecasts, inadequate sales efforts, and even poor customer service. The fates of all supply chain partners are interlinked: If the firms work together to serve consumers, they will all win. However, they can do that only if incentives are aligned. Companies must acknowledge that the problem of incentive misalignment exists and then determine its root cause and align or redesign incentives. They can improve alignment by, for instance, adopting revenue-sharing contracts, using technology to track previously hidden information, or working with intermediaries to build trust among network partners. It's also important to periodically reassess incentives, because even top-performing networks find that changes in technology or business conditions alter the alignment of incentives.

  3. Effect of Cement on Emulsified Asphalt Mixtures

    NASA Astrophysics Data System (ADS)

    Oruc, Seref; Celik, Fazil; Akpinar, M. Vefa

    2007-10-01

    Emulsified asphalt mixtures have environmental, economical, and logistical advantages over hot mixtures. However, they have attracted little attention as structural layers due to their inadequate performance and susceptibility to early life damage by rainfall. The objective of this article is to provide an improved insight into how the mechanical properties of emulsion mixtures may be improved and to determine the influence of cement on emulsified asphalt mixtures. Laboratory tests on strength, temperature susceptibility, water damage, creep and permanent deformation were implemented to evaluate the mechanical properties of emulsified asphalt mixtures. The test results showed that mechanical properties of emulsified asphalt mixtures have significantly improved with Portland cement addition. This experimental study suggested that cement modified asphalt emulsion mixtures might be an alternate way of a structural layer material in pavement.

  4. Supercritical Water Mixture (SCWM) Experiment

    NASA Technical Reports Server (NTRS)

    Hicks, Michael C.; Hegde, Uday G.

    2012-01-01

    The subject presentation, entitled, Supercritical Water Mixture (SCWM) Experiment, was presented at the International Space Station (ISS) Increment 33/34 Science Symposium. This presentation provides an overview of an international collaboration between NASA and CNES to study the behavior of a dilute aqueous solution of Na2SO4 (5% w) at near-critical conditions. The Supercritical Water Mixture (SCWM) investigation, serves as important precursor work for subsequent Supercritical Water Oxidation (SCWO) experiments. The SCWM investigation will be performed in DECLICs High Temperature Insert (HTI) for the purpose of studying critical fluid phenomena at high temperatures and pressures. The HTI includes a completely sealed and integrated test cell (i.e., Sample Cell Unit SCU) that will contain approximately 0.3 ml of the aqueous test solution. During the sequence of tests, scheduled to be performed in FY13, temperatures and pressures will be elevated to critical conditions (i.e., Tc = 374C and Pc = 22 MPa) in order to observe salt precipitation, precipitate agglomeration and precipitate transport in the presence of a temperature gradient without the influences of gravitational forces. This presentation provides an overview of the motivation for this work, a description of the DECLIC HTI hardware, the proposed test sequences, and a brief discussion of the scientific research objectives.

  5. Petroleum supply monthly, May 1994

    SciTech Connect

    Not Available

    1994-05-27

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum supply annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  6. Petroleum supply monthly, January 1996

    SciTech Connect

    1996-02-15

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  7. Petroleum supply monthly, September 1991

    SciTech Connect

    Not Available

    1991-09-30

    The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administrations for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics. 65 tabs.

  8. Petroleum supply monthly, October 1993

    SciTech Connect

    Not Available

    1993-10-26

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  9. Petroleum supply monthly, June 1994

    SciTech Connect

    Not Available

    1994-06-28

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  10. Petroleum Supply Monthly, August 1990

    SciTech Connect

    Not Available

    1990-10-30

    The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) district movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics.

  11. Petroleum supply monthly, July 1994

    SciTech Connect

    Not Available

    1994-07-26

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  12. Petroleum supply monthly, August 1994

    SciTech Connect

    Not Available

    1994-08-26

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  13. International Oil Supplies and Demands

    SciTech Connect

    Not Available

    1991-09-01

    The eleventh Energy Modeling Forum (EMF) working group met four times over the 1989--90 period to compare alternative perspectives on international oil supplies and demands through 2010 and to discuss how alternative supply and demand trends influence the world's dependence upon Middle Eastern oil. Proprietors of eleven economic models of the world oil market used their respective models to simulate a dozen scenarios using standardized assumptions. From its inception, the study was not designed to focus on the short-run impacts of disruptions on oil markets. Nor did the working group attempt to provide a forecast or just a single view of the likely future path for oil prices. The model results guided the group's thinking about many important longer-run market relationships and helped to identify differences of opinion about future oil supplies, demands, and dependence.

  14. International Oil Supplies and Demands

    SciTech Connect

    Not Available

    1992-04-01

    The eleventh Energy Modeling Forum (EMF) working group met four times over the 1989--1990 period to compare alternative perspectives on international oil supplies and demands through 2010 and to discuss how alternative supply and demand trends influence the world's dependence upon Middle Eastern oil. Proprietors of eleven economic models of the world oil market used their respective models to simulate a dozen scenarios using standardized assumptions. From its inception, the study was not designed to focus on the short-run impacts of disruptions on oil markets. Nor did the working group attempt to provide a forecast or just a single view of the likely future path for oil prices. The model results guided the group's thinking about many important longer-run market relationships and helped to identify differences of opinion about future oil supplies, demands, and dependence.

  15. A single supply biopotential amplifier.

    PubMed

    Spinelli, E M; Martinez, N H; Mayosky, M A

    2001-04-01

    A biopotential amplifier for single supply operation is presented. It uses a Driven Right Leg Circuit (DRL) to drive the patient's body to a DC common mode voltage, centering biopotential signals with respect to the amplifier's input voltage range. This scheme ensures proper range operation when a single power supply is used. The circuit described is especially suited for low consumption, battery-powered applications, requiring a single battery and avoiding switching voltage inverters to achieve dual supplies. The generic circuit is described and, as an example, a biopotential amplifier with a gain of 60 dB and a DC input range of +/-200 mV was implemented using low power operational amplifiers. A Common Mode Rejection Ratio (CMRR) of 126 dB at 50 Hz was achieved without trimming.

  16. The initial lunar supply base

    NASA Technical Reports Server (NTRS)

    Criswell, D.

    1979-01-01

    The first lunar supply base should have a mass less than 1000 tons, be deployed by 24 persons in 4 months, and be maintained by 10 persons. Output could be expanded 20 times in 5 years to 600,000 tons/yr by a factor of 10 expansion of the area of the solar array on the lunar surface, using low power soil beneficiation, increasing the fleet of mining vehicles, and illuminating the base continuously at night with lunar orbiting mirrors. The space manufacturing facility (SMF) will supply most of the mass (solar cells and orbiting mirrors) necessary for expansion. Several devices and procedures are suggested for development which could further reduce the total mass necessary to transport to the Moon to establish the initial lunar supply base.

  17. Petroleum supply monthly, July 1993

    SciTech Connect

    Not Available

    1993-07-29

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: Petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  18. Supply curves of conserved energy

    NASA Astrophysics Data System (ADS)

    Meier, A. K.

    1982-05-01

    Supply curves of conserved energy provide an accounting framework that expresses the potential for energy conservation. The economic worthiness of a conservation measure is expressed in terms of the cost of conserved energy, and a measure is considered economical when the cost of conserved energy is less than the price of the energy it replaces. A supply curve of conserved energy is independent of energy prices; however, the economical reserves of conserved energy will depend on energy prices. Double-counting of energy savings and error propagation are common problems when estimating conservation potentials, but supply curves minimize these difficulties and make their consequences predictable. The sensitivity of the cost of conserved energy is examined, as are variations in the optimal investment strategy in response to changes in inputs. Guidelines are presented for predicting the consequences of such changes.

  19. PFP supply fan motor starters

    SciTech Connect

    Keck, R.D.

    1995-05-31

    The Plutonium Finishing Plant (PFP) is currently stabilizing about 25 kg of Pu sludge; upon completion of this task, PFP will be maintained in a safe standby condition to await decision from the PFP NEPA review. It can take about 10 years to initiate and complete terminal cleanout after this; the facility will then be decommissioned and decontaminated. The 234-5Z ventilation system must continue to operate until terminal cleanout. Part of the ventilation system is the seismic fan shutdown system which shuts down the ventilation supply fans in case of strong earthquake. This document presents criteria for installing solid state, reduced voltage motor starters and isolation contactors for the 8 main ventilation supply fans. The isolation contactors will shutdown the supply fans in event of earthquake.

  20. Leading a supply chain turnaround.

    PubMed

    Slone, Reuben E

    2004-10-01

    Just five years ago, salespeople at Whirlpool were in the habit of referring to their supply chain organization as the "sales disablers." Now the company excels at getting products to the right place at the right time--while managing to keep inventories low. How did that happen? In this first-person account, Reuben Slone, Whirlpool's vice president of Global Supply Chain, describes how he and his colleagues devised the right supply chain strategy, sold it internally, and implemented it. Slone insisted that the right focal point for the strategy was the satisfaction of consumers at the end of the supply chain. Most supply chain initiatives do the opposite: They start with the realities of a company's manufacturing base and proceed from there. Through a series of interviews with trade customers large and small, his team identified 27 different capabilities that drove industry perceptions of Whirlpool's performance. Knowing it was infeasible to aim for world-class performance across all of them, Slone weighed the costs of excelling at each and found the combination of initiatives that would provide overall competitive advantage. A highly disciplined project management office and broad training in project management were key to keeping work on budget and on benefit. Slone set an intense pace--three "releases" of new capabilities every month--that the group maintains to this day. Lest this seem like a technology story, however, Slone insists it is just as much a "talent renaissance." People are proud today to be part of Whirlpool's supply chain organization, and its new generation of talent will give the company a competitive advantage for years to come.

  1. Method and apparatus for controlling fuel/air mixture in a lean burn engine

    DOEpatents

    Kubesh, John Thomas; Dodge, Lee Gene; Podnar, Daniel James

    1998-04-07

    The system for controlling the fuel/air mixture supplied to a lean burn engine when operating on natural gas, gasoline, hydrogen, alcohol, propane, butane, diesel or any other fuel as desired. As specific humidity of air supplied to the lean burn engine increases, the oxygen concentration of exhaust gas discharged by the engine for a given equivalence ratio will decrease. Closed loop fuel control systems typically attempt to maintain a constant exhaust gas oxygen concentration. Therefore, the decrease in the exhaust gas oxygen concentration resulting from increased specific humidity will often be improperly attributed to an excessive supply of fuel and the control system will incorrectly reduce the amount of fuel supplied to the engine. Also, the minimum fuel/air equivalence ratio for a lean burn engine to avoid misfiring will increase as specific humidity increases. A relative humidity sensor to allow the control system to provide a more enriched fuel/air mixture at high specific humidity levels. The level of specific humidity may be used to compensate an output signal from a universal exhaust gas oxygen sensor for changing oxygen concentrations at a desired equivalence ratio due to variation in specific humidity specific humidity. As a result, the control system will maintain the desired efficiency, low exhaust emissions and power level for the associated lean burn engine regardless of the specific humidity level of intake air supplied to the lean burn engine.

  2. Petroleum supply monthly, January 1994

    SciTech Connect

    Not Available

    1994-01-01

    Data presented describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  3. US energy consumption and supply

    NASA Astrophysics Data System (ADS)

    Vanatta, C. M.

    1981-01-01

    Energy consumption and cost in 1978 and 1979 are discussed with emphasis on the effect of imported oil on the economy of the United States. Some of the international aspects of energy supply are described, and actions to meet the probability of a cutoff of oil imports from the Persian Gulf area are suggested. Short and long range strategies for ensuring energy self sufficiency are discussed. A rationale for major, long range dependence on fission and fusion power is given, and the possible advantages of a nearly all electric energy system are mentioned. Projection of energy consumption and supply to the year 2020 based upon economic and demographic models is discussed.

  4. Supply prices to increase slightly.

    PubMed

    Hard, R

    1991-03-05

    Expect hospital supply prices to increase by about 3 percent to 4 percent during 1991, says the new economic forecast from the Joint Purchasing Corp. (JPC), New York City. JPC's report may help reduce the uncertainty for those making supply price forecasts during the current recession. The Economic Forecast and Budget Impact Report presents economic information from industry analysts and publishes the data in a single volume. The JPC forecast can be used as a guide to help determine price changes; however, it's also important to consider changes in consumption, utilization, and quality when using the report, says JPC's president.

  5. Mixtures Research at NIEHS: An Evolving Program

    PubMed Central

    Rider, Cynthia V; Carlin, Danielle J; DeVito, Micheal J; Thompson, Claudia L; Walker, Nigel J

    2014-01-01

    The National Institute of Environmental Health Sciences (NIEHS) has a rich history in evaluating the toxicity of mixtures. The types of mixtures assessed by the Division of the National Toxicology Program (DNTP) and the extramural community (through the Division of Extramural Research and Training (DERT)) have included a broad range of chemicals and toxicants, with each study having a unique set of questions and design considerations. Some examples of the types of mixtures studied include: groundwater contaminants, pesticides/fertilizers, dioxin-like chemicals (assessing the toxic equivalency approach), drug combinations, air pollution, metals, polycyclic aromatic hydrocarbons, technical mixtures (e.g. pentachlorophenol, flame retardants), and mixed entities (e.g. herbals, asbestos). These endeavors have provided excellent data on the toxicity of specific mixtures and have been informative to the human health risk assessment process in general (e.g. providing data on low dose exposures to environmental chemicals). However, the mixtures research effort at NIEHS, to date, has been driven by test article nominations to the DNTP or by investigator-initiated research through DERT. Recently, the NIEHS has embarked upon an effort to coordinate mixtures research across both intramural and extramural divisions in order to maximize mixtures research results. A path forward for NIEHS mixtures research will be based on feedback from a Request for Information (RFI) designed to gather up-to-date views on the knowledge gaps and roadblocks to evaluating mixtures and performing cumulative risk assessment, and a workshop organized to bring together mixtures experts from risk assessment, exposure science, biology, epidemiology, and statistics. The future of mixtures research at NIEHS will include projects from nominations to DNTP, studies by extramural investigators, and collaborations across government agencies that address high-priority questions in the field of mixtures research

  6. Mixtures research at NIEHS: an evolving program.

    PubMed

    Rider, Cynthia V; Carlin, Danielle J; Devito, Micheal J; Thompson, Claudia L; Walker, Nigel J

    2013-11-16

    The National Institute of Environmental Health Sciences (NIEHS) has a rich history in evaluating the toxicity of mixtures. The types of mixtures assessed by the Division of the National Toxicology Program (DNTP) and the extramural community (through the Division of Extramural Research and Training, DERT) have included a broad range of chemicals and toxicants, with each study having a unique set of questions and design considerations. Some examples of the types of mixtures studied include: groundwater contaminants, pesticides/fertilizers, dioxin-like chemicals (assessing the toxic equivalency approach), drug combinations, air pollution, metals, polycyclic aromatic hydrocarbons, technical mixtures (e.g., pentachlorophenol, flame retardants), and mixed entities (e.g., herbals, asbestos). These endeavors have provided excellent data on the toxicity of specific mixtures and have been informative to the human health risk assessment process in general (e.g., providing data on low dose exposures to environmental chemicals). However, the mixtures research effort at NIEHS, to date, has been driven by test article nominations to the DNTP or by investigator-initiated research through DERT. Recently, the NIEHS has embarked upon an effort to coordinate mixtures research across both intramural and extramural divisions in order to maximize mixtures research results. A path forward for NIEHS mixtures research will be based on feedback from a Request for Information (RFI) designed to gather up-to-date views on the knowledge gaps and roadblocks to evaluating mixtures and performing cumulative risk assessment, and a workshop organized to bring together mixtures experts from risk assessment, exposure science, biology, epidemiology, and statistics. The future of mixtures research at NIEHS will include projects from nominations to DNTP, studies by extramural investigators, and collaborations across government agencies that address high-priority questions in the field of mixtures research.

  7. Interdiffusion in binary ionic mixtures

    SciTech Connect

    Boercker, D.B.; Pollock, E.L.

    1987-08-15

    In this paper we present molecular-dynamics and kinetic-theory calculations of the interdiffusion coefficients in dense binary ionic mixtures for conditions appropriate to both astrophysical and inertial-confinement fusion (ICF) plasmas. The diffusion coefficient is the product of a Green-Kubo integral and a thermodynamic prefactor. The molecular-dynamics and kinetic-theory estimates of the Green-Kubo portion agree very well, and it is found that this integral may also be well represented by the usual concentration-weighted sum of self-diffusion coefficients. In addition, the low-density limit of the thermodynamic prefactor is shown to represent an enhancement of the diffusion by the ''ambipolar'' electric field.

  8. Art Supply Inventors. Children's Art Diary.

    ERIC Educational Resources Information Center

    Szekely, George

    2001-01-01

    Discusses types of art materials that children enjoy using in their artworks. Explores the art materials such as tasty art supplies, such as candy; peeled supplies, such as pencil shavings; sticky art supplies, such as Band-Aids; and fast-food supplies, such as forks and spoons. (CMK)

  9. 10 CFR 218.11 - Supply orders.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 10 Energy 3 2011-01-01 2011-01-01 false Supply orders. 218.11 Section 218.11 Energy DEPARTMENT OF ENERGY OIL STANDBY MANDATORY INTERNATIONAL OIL ALLOCATION Supply Orders § 218.11 Supply orders. (a) A...) The DOE shall serve a copy of the supply order on the firm directed to act as stated therein. (c)...

  10. 10 CFR 218.11 - Supply orders.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 10 Energy 3 2013-01-01 2013-01-01 false Supply orders. 218.11 Section 218.11 Energy DEPARTMENT OF ENERGY OIL STANDBY MANDATORY INTERNATIONAL OIL ALLOCATION Supply Orders § 218.11 Supply orders. (a) A...) The DOE shall serve a copy of the supply order on the firm directed to act as stated therein. (c)...

  11. 46 CFR 108.467 - Water supply.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 4 2012-10-01 2012-10-01 false Water supply. 108.467 Section 108.467 Shipping COAST... Fire Extinguishing Systems Foam Extinguishing Systems § 108.467 Water supply. The water supply of a foam extinguishing system must not be the water supply of the fire main system on the unit unless...

  12. 46 CFR 108.467 - Water supply.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 46 Shipping 4 2011-10-01 2011-10-01 false Water supply. 108.467 Section 108.467 Shipping COAST... Fire Extinguishing Systems Foam Extinguishing Systems § 108.467 Water supply. The water supply of a foam extinguishing system must not be the water supply of the fire main system on the unit unless...

  13. 46 CFR 108.467 - Water supply.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 4 2014-10-01 2014-10-01 false Water supply. 108.467 Section 108.467 Shipping COAST... Fire Extinguishing Systems Foam Extinguishing Systems § 108.467 Water supply. The water supply of a foam extinguishing system must not be the water supply of the fire main system on the unit unless...

  14. 46 CFR 108.467 - Water supply.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Water supply. 108.467 Section 108.467 Shipping COAST... Fire Extinguishing Systems Foam Extinguishing Systems § 108.467 Water supply. The water supply of a foam extinguishing system must not be the water supply of the fire main system on the unit unless...

  15. 46 CFR 108.467 - Water supply.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 4 2013-10-01 2013-10-01 false Water supply. 108.467 Section 108.467 Shipping COAST... Fire Extinguishing Systems Foam Extinguishing Systems § 108.467 Water supply. The water supply of a foam extinguishing system must not be the water supply of the fire main system on the unit unless...

  16. An Analysis of Class II Supplies Requisitions in the Korean Army’s Organizational Supply

    DTIC Science & Technology

    2009-03-26

    Retail Supply System SBMA Standard Book of Material Allowance SCM Supply Chain Management SCM Supply Chain Management SDI Supplies Daily...issues. The Standard Army Retail Supply System (SARSS) is currently used at Retail Level Supply. SARSS is the primary automation system used in the... system features provides SPBS-R and ULLS-S4 functionality. (4) SARSS is currently used at Retail Level Supply. The solutions to improve requisition

  17. Water Supply Infrastructure System Surety

    SciTech Connect

    EKMAN,MARK E.; ISBELL,DARYL

    2000-01-06

    The executive branch of the United States government has acknowledged and identified threats to the water supply infrastructure of the United States. These threats include contamination of the water supply, aging infrastructure components, and malicious attack. Government recognition of the importance of providing safe, secure, and reliable water supplies has a historical precedence in the water works of the ancient Romans, who recognized the same basic threats to their water supply infrastructure the United States acknowledges today. System surety is the philosophy of ''designing for threats, planning for failure, and managing for success'' in system design and implementation. System surety is an alternative to traditional compliance-based approaches to safety, security, and reliability. Four types of surety are recognized: reactive surety; proactive surety, preventative surety; and fundamental, inherent surety. The five steps of the system surety approach can be used to establish the type of surety needed for the water infrastructure and the methods used to realize a sure water infrastructure. The benefit to the water industry of using the system surety approach to infrastructure design and assessment is a proactive approach to safety, security, and reliability for water transmission, treatment, distribution, and wastewater collection and treatment.

  18. Supply Curves of Conserved Energy

    SciTech Connect

    Meier, Alan Kevin

    1982-05-01

    Supply curves of conserved energy provide an accounting framework that expresses the potential for energy conservation. The economic worthiness of a conservation measure is expressed in terms of the cost of conserved energy, and a measure is considered economical when the cost of conserved energy is less than the price of the energy it replaces. A supply curve of conserved energy is independent of energy prices; however, the economical reserves of conserved energy will depend on energy prices. Double-counting of energy savings and error propagation are common problems when estimating conservation potentials, but supply curves minimize these difficulties and make their consequences predictable. The sensitivity of the cost of conserved energy is examined, as are variations in the optimal investment strategy in response to changes in inputs. Guidelines are presented for predicting the consequences of such changes. The conservation supply curve concept can be applied to peak power, water, pollution, and other markets where consumers demand a service rather than a particular good.

  19. Economic drivers of mineral supply

    USGS Publications Warehouse

    Wagner, Lorie A.; Sullivan, Daniel E.; Sznopek, John L.

    2003-01-01

    The debate over the adequacy of future supplies of mineral resources continues in light of the growing use of mineral-based materials in the United States. According to the U.S. Geological Survey, the quantity of new materials utilized each year has dramatically increased from 161 million tons2 in 1900 to 3.2 billion tons in 2000. Of all the materials used during the 20th century in the United States, more than half were used in the last 25 years. With the Earth?s endowment of natural resources remaining constant, and increased demand for resources, economic theory states that as depletion approaches, prices rise. This study shows that many economic drivers (conditions that create an economic incentive for producers to act in a particular way) such as the impact of globalization, technological improvements, productivity increases, and efficient materials usage are at work simultaneously to impact minerals markets and supply. As a result of these economic drivers, the historical price trend of mineral prices3 in constant dollars has declined as demand has risen. When price is measured by the cost in human effort, the price trend also has been almost steadily downward. Although the United States economy continues its increasing mineral consumption trend, the supply of minerals has been able to keep pace. This study shows that in general supply has grown faster than demand, causing a declining trend in mineral prices.

  20. Estimating Supplies Program: Evaluation Report

    DTIC Science & Technology

    2007-11-02

    214 Ingrown Toenails Bilateral With Secondary Infections Unresolvable At Echelon 2 215 Ingrown Toenails Without Secondary Infection 216 Herpes...Select functional areas that provide treatment for the patient stream you input. For example, if you select the Surgical Company Operating Room...readiness. (U) The primary application of supply estimation is to determine logistical requirements for medical treatment . Traditionally, medical

  1. The Management of Groundwater Supplies.

    ERIC Educational Resources Information Center

    Hall, P. L.

    1978-01-01

    The manager of a groundwater supply system must be involved in many different disciplines if he or she is to manage the system effectively. In areas in which specialized expertise is necessary, it can be obtained from consultants or government agencies. (BB)

  2. Perceptual and imaginary mixtures in chemosensation.

    PubMed

    Schifferstein, H N

    1997-02-01

    D. Algom and W.S. Cain (1991) reported similar interaction patterns for perceived and imaginary mixtures of odorants. However, their experimental design did not allow sensitive statistical testing to demonstrate differences between conditions. Three experiments on 16 mixtures of sucrose-citric acid mixtures yielded significantly different interaction pattern for perceived and imaginary mixtures. Inconsistencies in the degrees of suppression in the imaginary condition suggested that participants did not base their responses on the inspection of a mental image but on incomplete implicit or explicit knowledge of sensory interactions. Participants knew the phenomenon of mixture suppression and knew that its effects were level dependent, but they were unable to predict the exact intensity of a mixture on the basis of the intensities of its unmixed components.

  3. Mixture distribution in a multi-valve twin-spark ignition engine equipped with high-pressure multi-hole injectors

    NASA Astrophysics Data System (ADS)

    Mitroglou, N.; Arcoumanis, C.; Mori, K.; Motoyama, Y.

    2006-07-01

    Laser-induced fluorescence has been mainly used to characterise the two-dimensional fuel vapour concentration inside the cylinder of a multi-valve twin-spark ignition engine equipped with high-pressure multi-hole injectors. The effects of injection timing, in-cylinder charge motion and injector tip layout have been quantified. The flexibility in nozzle design of the multi-hole injectors has proven to be a powerful tool in terms of matching overall spray cone angle and number of holes to specific engine configurations. Injection timing was found to control spray impingement on the piston and cylinder wall, thus contributing to quick and efficient fuel evaporation. It was confirmed that in-cylinder charge motion plays a major role in engine's stable operation by assisting in the transportation of the air-fuel mixture towards the ignition locations (i.e. spark-plugs) in the way of a uniformly distributed charge or by preserving stratification of the charge depending on operating mode of the engine.

  4. Petroleum supply monthly, June 1993

    SciTech Connect

    Not Available

    1993-06-28

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures ih the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. Most time series include preliminary estimates for one month based on the Weekly Petroleum Supply Reporting System; statistics based on the most recent data from the Monthly Petroleum Supply Reporting System (MPSRS); and statistics published in prior issues of the PSM and PSA. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas - - the United States (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. The statistics are developed from monthly survey forms submitted by respondents to the EIA and from data provided firom other sources.

  5. Petroleum supply monthly, March 1994

    SciTech Connect

    Not Available

    1994-03-30

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. Most time series include preliminary estimates for one month based on the Weekly Petroleum Supply Reporting System; statistics based on the most recent data from the Monthly Petroleum Supply Reporting System (MPSRS); and statistics published in prior issues of the PSM and PSA. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas -- the United States (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. The statistics are developed from monthly survey forms submitted by respondents to the EIA and from data provided from other sources.

  6. Supply chain challenges. building relationships.

    PubMed

    Beth, Scott; Burt, David N; Copacino, William; Gopal, Chris; Lee, Hau L; Lynch, Robert Porter; Morris, Sandra

    2003-07-01

    Supply chain management is all about software and systems, right? Put in the best technology, sit back, and watch as your processes run smoothly and the savings roll in? Apparently not. When HBR convened a panel of leading thinkers in the field of supply chain management, technology was not top of mind. People and relationships were the dominant issues of the day. The opportunities and problems created by globalization, for example, are requiring companies to establish relationships with new types of suppliers. The ever-present pressure for speed and cost containment is making it even more important to break down stubbornly high internal barriers and establish more effective cross-functional relationships. The costs of failure have never been higher. The leading supply chain performers are applying new technology, new innovations, and process thinking to far greater advantage than the laggards, reaping tremendous gains in all the variables that affect shareholder value: cost, customer service, asset productivity, and revenue generation. And the gap between the leaders and the losers is growing in almost every industry. This roundtable gathered many of the leading thinkers and doers in the field of supply chain management, including practitioners Scott Beth of Intuit, Sandra Morris of Intel, and Chris Gopal of Unisys. David Burt of the University of San Diego and Stanford's Hau Lee bring the latest research from academia. Accenture's William Copacino and the Warren Company's Robert Porter Lynch offer the consultant's perspectives. Together, they take a wide-ranging view of such topics as developing talent, the role of the chief executive, and the latest technologies, exploring both the tactical and the strategic in the current state of supply chain management.

  7. Thermal Analysis of Various Epoxy Mixtures.

    DTIC Science & Technology

    1986-03-01

    Dicyandiamide Thermal analysis Accelerator r20 ABSTRAC r (Continue on revre side If necesary and identif by. block riimeyp.) 4 4 (SEE REVERSE SIDE...mixed with Monuron. Also, three-component mixtures, epoxide + Dicy/Monuron, were prepared with dicyandiamide . The mixtures were cured by differential... dicyandiamide and Monuron, on the curing process, was simulated by the isothermal reaction of two mixtures. A type of reaction kinetics having the

  8. Near azeotropic mixture substitute for dichlorodifluoromethane

    NASA Technical Reports Server (NTRS)

    Jones, Jack A. (Inventor)

    1998-01-01

    A refrigerant and a process of formulating thereof that consists of a mixture of a first mole fraction of CH.sub.2 FCF.sub.3 and a second mole fraction of a component selected from the group consisting of a mixture of CHClFCF.sub.3 and CH.sub.3 CClF.sub.2 ; a mixture of CHF.sub.2 CH.sub.3 and CH.sub.3 CClF.sub.2 ; and a mixture of CHClFCF.sub.3, CH.sub.3 CClF.sub.2 and CHF.sub.2 CH.sub.3.

  9. Cluster kinetics model for mixtures of glassformers

    NASA Astrophysics Data System (ADS)

    Brenskelle, Lisa A.; McCoy, Benjamin J.

    2007-10-01

    For glassformers we propose a binary mixture relation for parameters in a cluster kinetics model previously shown to represent pure compound data for viscosity and dielectric relaxation as functions of either temperature or pressure. The model parameters are based on activation energies and activation volumes for cluster association-dissociation processes. With the mixture parameters, we calculated dielectric relaxation times and compared the results to experimental values for binary mixtures. Mixtures of sorbitol and glycerol (seven compositions), sorbitol and xylitol (three compositions), and polychloroepihydrin and polyvinylmethylether (three compositions) were studied.

  10. Dielectric gas mixtures containing sulfur hexafluoride

    DOEpatents

    Cooke, Chathan M.

    1979-01-01

    Electrically insulating gaseous media of unexpectedly high dielectric strength comprised of mixtures of two or more dielectric gases are disclosed wherein the dielectric strength of at least one gas in each mixture increases at less than a linear rate with increasing pressure and the mixture gases are present in such proportions that the sum of their electrical discharge voltages at their respective partial pressures exceeds the electrical discharge voltage of each individual gas at the same temperature and pressure as that of the mixture.

  11. Reducing phosphorus release from paddy soils by a fly ash-gypsum mixture.

    PubMed

    Lee, Chang Hoon; Lee, Yong Bok; Lee, Hyup; Kim, Pil Joo

    2007-07-01

    A mixture of fly ash and phospho-gypsum (50:50, wtwt(-1)) was selected to study its potential to supply Ca and Si to rice while reducing B toxicity. We expected that the high Ca content in this mixture might convert water-soluble P to less soluble forms and thereby reduce the loss of soil P to surface runoff. The mixture was applied at rates of 0, 20, 40, and 60 Mgha(-1) in two paddy soils of contrasting textures (silt loam in Yehari and loamy sand in Daegok). The mixture significantly reduced water-soluble phosphate (W-P) in the surface soils by shifting from W-P and iron bound-P (Fe-P) to calcium bound-P (Ca-P) and aluminum bound-P (Al-P) during rice cultivation in both soils. Lancaster and Mehlich 3 extractable P increased significantly with application rate due to high contents of P and Si in the mixture. Mixtures of fly ash and phospho-gypsum should reduce P loss from rice paddy soils and increase soil fertility.

  12. Low energy consumption method for separating gaseous mixtures and in particular for medium purity oxygen production

    DOEpatents

    Jujasz, Albert J.; Burkhart, James A.; Greenberg, Ralph

    1988-01-01

    A method for the separation of gaseous mixtures such as air and for producing medium purity oxygen, comprising compressing the gaseous mixture in a first compressor to about 3.9-4.1 atmospheres pressure, passing said compressed gaseous mixture in heat exchange relationship with sub-ambient temperature gaseous nitrogen, dividing the cooled, pressurized gaseous mixture into first and second streams, introducing the first stream into the high pressure chamber of a double rectification column, separating the gaseous mixture in the rectification column into a liquid oxygen-enriched stream and a gaseous nitrogen stream and supplying the gaseous nitrogen stream for cooling the compressed gaseous mixture, removing the liquid oxygen-enriched stream from the low pressure chamber of the rectification column and pumping the liquid, oxygen-enriched steam to a predetermined pressure, cooling the second stream, condensing the cooled second stream and evaporating the oxygen-enriched stream in an evaporator-condenser, delivering the condensed second stream to the high pressure chamber of the rectification column, and heating the oxygen-enriched stream and blending the oxygen-enriched stream with a compressed blend-air stream to the desired oxygen concentration.

  13. Ultracentrifuge for separating fluid mixtures

    DOEpatents

    Lowry, Ralph A.

    1976-01-01

    1. A centrifuge for the separation of fluid mixtures having light and heavy fractions comprising a cylindrical rotor, disc type end-plugs closing the ends of the rotor, means for mounting said rotor for rotation about its cylindrical axis, a housing member enclosing the rotor, a vacuum chamber in said housing about the central portion of the rotor, a collection chamber at each end of the housing, the innermost side of which is substantially formed by the outer face of the end-plug, means for preventing flow of the fluid from the collection chambers to said vacuum chamber, at least one of said end-plugs having a plurality of holes therethrough communicating between the collection chamber adjacent thereto and the inside of the rotor to induce countercurrent flow of the fluid in the centrifuge, means for feeding fluid to be processed into the centrifuge, means communicating with the collection chambers to extract the light and heavy separated fractions of the fluid, and means for rotating the rotor.

  14. 1992 Conversion Resources Supply Document

    SciTech Connect

    Not Available

    1992-03-01

    In recent years conservation of electric power has become an integral part of utility planning. The 1980 Pacific Northwest Electric Power Planning and Conservation Act (Northwest Power Act) requires that the region consider conservation potential in planning acquisitions of resources to meet load growth. The Bonneville Power Administration (BPA) developed its first estimates of conservation potential in 1982. Since that time BPA has updated its conservation supply analyses as a part of its Resource Program and other planning efforts. Major updates were published in 1985 and in January 1990. This 1992 document presents updated supply curves, which are estimates of the savings potential over time (cumulative savings) at different cost levels of energy conservation measures (ECMs). ECMs are devices, pieces of equipment, or actions that increase the efficiency of electricity use and reduce the amount of electricity used by end-use equipment.

  15. Spatially Characterizing Effective Timber Supply

    NASA Technical Reports Server (NTRS)

    Berry, J. K.; Sailor, J.

    1982-01-01

    The structure of a computer-oriented cartographic model for assessing roundwood supply for generation of base load electricity is discussed. The model provides an analytical procedure for coupling spatial information of harvesting economics and owner willingness to sell stumpages. Supply is characterized in terms of standing timber; of accessibility considering various harvesting and hauling factors; and of availability as affected by ownership and residential patterns. Factors governing accessibility to timber include effective harvesting distance to haulic roads as modified by barriers and slopes. Haul distance is expressed in units that take into account the relative ease of travel along various road types to a central processing facility. Areas of accessible timber are grouped into spatial units, termed 'timbersheds', of common access to particular haul road segments that belong to unique 'transport zones'. Timber availability considerations include size of ownership parcels, housing density and excluded areas. The analysis techniques are demonstrated for a cartographic data base in western Massachusetts.

  16. Petroleum Supply Monthly, July 1990

    SciTech Connect

    Not Available

    1990-09-28

    Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  17. Petroluem Supply Monthly, May 1993

    SciTech Connect

    Not Available

    1993-06-04

    Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  18. High voltage DC power supply

    DOEpatents

    Droege, T.F.

    1989-12-19

    A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively. 7 figs.

  19. High voltage DC power supply

    DOEpatents

    Droege, Thomas F.

    1989-01-01

    A high voltage DC power supply having a first series resistor at the output for limiting current in the event of a short-circuited output, a second series resistor for sensing the magnitude of output current, and a voltage divider circuit for providing a source of feedback voltage for use in voltage regulation is disclosed. The voltage divider circuit is coupled to the second series resistor so as to compensate the feedback voltage for a voltage drop across the first series resistor. The power supply also includes a pulse-width modulated control circuit, having dual clock signals, which is responsive to both the feedback voltage and a command voltage, and also includes voltage and current measuring circuits responsive to the feedback voltage and the voltage developed across the second series resistor respectively.

  20. Supply Current Diagnosis in VLSI

    NASA Technical Reports Server (NTRS)

    Frenzel, J. F.; Marinos, P. N.

    1990-01-01

    This paper presents a technique based upon the power supply current signature (cd) which allows for the testing of mixed-signal systems, in situ. Through experiments with a microprocessor, the cd is shown to contain important information concerning the operational status of the system which may be easily extracted using approaches based on statistical signal detection theory. The fault-detection performance of these techniques is compared to that achieved through auto-regressive modeling of the cd.

  1. Replenishable food supply on Mars

    NASA Astrophysics Data System (ADS)

    1990-11-01

    The design team's present objective is to design a facility which will provide an environment to grow plants on the surface of Mars for a continuous supply of food for a ten-man crew. The main focus of the project is the design of a greenhouse. Concentration of the current design effort is on the outer structure, internal layout, and construction methods. The project was conducted by undergraduate students at Prairie View A&M University during Fall 1989 and Spring 1990.

  2. Dietary mineral supplies in Africa

    PubMed Central

    Joy, Edward J M; Ander, E Louise; Young, Scott D; Black, Colin R; Watts, Michael J; Chilimba, Allan D C; Chilima, Benson; Siyame, Edwin W P; Kalimbira, Alexander A; Hurst, Rachel; Fairweather-Tait, Susan J; Stein, Alexander J; Gibson, Rosalind S; White, Philip J; Broadley, Martin R

    2014-01-01

    Dietary micronutrient deficiencies (MNDs) are widespread, yet their prevalence can be difficult to assess. Here, we estimate MND risks due to inadequate intakes for seven minerals in Africa using food supply and composition data, and consider the potential of food-based and agricultural interventions. Food Balance Sheets (FBSs) for 46 countries were integrated with food composition data to estimate per capita supply of calcium (Ca), copper (Cu), iron (Fe), iodine (I), magnesium (Mg), selenium (Se) and zinc (Zn), and also phytate. Deficiency risks were quantified using an estimated average requirement (EAR) ‘cut-point’ approach. Deficiency risks are highest for Ca (54% of the population), followed by Zn (40%), Se (28%) and I (19%, after accounting for iodized salt consumption). The risk of Cu (1%) and Mg (<1%) deficiency are low. Deficiency risks are generally lower in the north and west of Africa. Multiple MND risks are high in many countries. The population-weighted mean phytate supply is 2770 mg capita−1 day−1. Deficiency risks for Fe are lower than expected (5%). However, ‘cut-point’ approaches for Fe are sensitive to assumptions regarding requirements; e.g. estimates of Fe deficiency risks are 43% under very low bioavailability scenarios consistent with high-phytate, low-animal protein diets. Fertilization and breeding strategies could greatly reduce certain MNDs. For example, meeting harvestplus breeding targets for Zn would reduce dietary Zn deficiency risk by 90% based on supply data. Dietary diversification or direct fortification is likely to be needed to address Ca deficiency risks. PMID:24524331

  3. Replenishable food supply on Mars

    NASA Technical Reports Server (NTRS)

    1990-01-01

    The design team's present objective is to design a facility which will provide an environment to grow plants on the surface of Mars for a continuous supply of food for a ten-man crew. The main focus of the project is the design of a greenhouse. Concentration of the current design effort is on the outer structure, internal layout, and construction methods. The project was conducted by undergraduate students at Prairie View A&M University during Fall 1989 and Spring 1990.

  4. THE VISCOSITY OF HELIUM-CESIUM MIXTURES,

    DTIC Science & Technology

    The viscosities of helium-cesium mixtures having mole fractions of cesium from zero to unity were evaluated using a Lennard - Jones 6-12 interaction potential for all encounters in the Enskog Chapman expressions for the viscosity of a binary mixture. (Author)

  5. THE RECOVERY OF URANIUM FROM GAS MIXTURE

    DOEpatents

    Jury, S.H.

    1964-03-17

    A method of separating uranium from a mixture of uranium hexafluoride and other gases is described that comprises bringing the mixture into contact with anhydrous calcium sulfate to preferentially absorb the uranium hexafluoride on the sulfate. The calcium sulfate is then leached with a selective solvent for the adsorbed uranium. (AEC)

  6. Mixture Modeling: Applications in Educational Psychology

    ERIC Educational Resources Information Center

    Harring, Jeffrey R.; Hodis, Flaviu A.

    2016-01-01

    Model-based clustering methods, commonly referred to as finite mixture modeling, have been applied to a wide variety of cross-sectional and longitudinal data to account for heterogeneity in population characteristics. In this article, we elucidate 2 such approaches: growth mixture modeling and latent profile analysis. Both techniques are…

  7. Mixture Modeling of Individual Learning Curves

    ERIC Educational Resources Information Center

    Streeter, Matthew

    2015-01-01

    We show that student learning can be accurately modeled using a mixture of learning curves, each of which specifies error probability as a function of time. This approach generalizes Knowledge Tracing [7], which can be viewed as a mixture model in which the learning curves are step functions. We show that this generality yields order-of-magnitude…

  8. Gas mixtures for spark gap closing switches

    DOEpatents

    Christophorou, L.G.; McCorkle, D.L.; Hunter, S.R.

    1987-02-20

    Gas mixtures for use in spark gap closing switches comprised of fluorocarbons and low molecular weight, inert buffer gases. To this can be added a third gas having a low ionization potential relative to the buffer gas. The gas mixtures presented possess properties that optimized the efficiency spark gap closing switches. 6 figs.

  9. Process Dissociation and Mixture Signal Detection Theory

    ERIC Educational Resources Information Center

    DeCarlo, Lawrence T.

    2008-01-01

    The process dissociation procedure was developed in an attempt to separate different processes involved in memory tasks. The procedure naturally lends itself to a formulation within a class of mixture signal detection models. The dual process model is shown to be a special case. The mixture signal detection model is applied to data from a widely…

  10. Gas mixtures for spark gap closing switches

    DOEpatents

    Christophorou, Loucas G.; McCorkle, Dennis L.; Hunter, Scott R.

    1988-01-01

    Gas mixtures for use in spark gap closing switches comprised of fluorocarbons and low molecular weight, inert buffer gases. To this can be added a third gas having a low ionization potential relative to the buffer gas. The gas mixtures presented possess properties that optimized the efficiency spark gap closing switches.

  11. Separation of organic azeotropic mixtures by pervaporation

    SciTech Connect

    Baker, R.W.

    1991-12-01

    Distillation is a commonly used separation technique in the petroleum refining and chemical processing industries. However, there are a number of potential separations involving azetropic and close-boiling organic mixtures that cannot be separated efficiently by distillation. Pervaporation is a membrane-based process that uses selective permeation through membranes to separate liquid mixtures. Because the separation process is not affected by the relative volatility of the mixture components being separated, pervaporation can be used to separate azetropes and close-boiling mixtures. Our results showed that pervaporation membranes can be used to separate azeotropic mixtures efficiently, a result that is not achievable with simple distillation. The membranes were 5--10 times more permeable to one of the components of the mixture, concentrating it in the permeate stream. For example, the membrane was 10 times more permeable to ethanol than methyl ethyl ketone, producing 60% ethanol permeate from an azeotropic mixture of ethanol and methyl ethyl ketone containing 18% ethanol. For the ethyl acetate/water mixture, the membranes showed a very high selectivity to water (> 300) and the permeate was 50--100 times enriched in water relative to the feed. The membranes had permeate fluxes on the order of 0.1--1 kg/m{sup 2}{center dot}h in the operating range of 55--70{degrees}C. Higher fluxes were obtained by increasing the operating temperature.

  12. The future of oil supply.

    PubMed

    Miller, Richard G; Sorrell, Steven R

    2014-01-13

    Abundant supplies of oil form the foundation of modern industrial economies, but the capacity to maintain and grow global supply is attracting increasing concern. Some commentators forecast a peak in the near future and a subsequent terminal decline in global oil production, while others highlight the recent growth in 'tight oil' production and the scope for developing unconventional resources. There are disagreements over the size, cost and recoverability of different resources, the technical and economic potential of different technologies, the contribution of different factors to market trends and the economic implications of reduced supply. Few debates are more important, more contentious, more wide-ranging or more confused. This paper summarizes the main concepts, terms, issues and evidence that are necessary to understand the 'peak oil' debate. These include: the origin, nature and classification of oil resources; the trends in oil production and discoveries; the typical production profiles of oil fields, basins and producing regions; the mechanisms underlying those profiles; the extent of depletion of conventional oil; the risk of an approaching peak in global production; and the potential of various mitigation options. The aim is to introduce the subject to non-specialist readers and provide a basis for the subsequent papers in this Theme Issue.

  13. Radon in ground water supplies

    SciTech Connect

    Dixon, K.L.; Lee, R.G.

    1989-06-01

    In September 1986, the System Water Quality Department of the American Water Works Service Co. began conducting a radon survey that was designed to determine the levels of radon in American ground water supplies, and to assess the radon removal efficiency of existing treatment processes such as filtration through granular activated carbon (GAC) and various forms of aeration. The survey found that companies in the northeastern part of the country experienced the highest levels of radon in ground water supplies. The highest concentrations were in individual wells in New Hampshire, Maryland, Connecticut, Rhode Island, New Jersey, Pennsylvania and California. The analytical results from the occurrence phase of the survey seemed to correlate well with the known geology of the aquifer materials from which samples of ground water were drawn. The highest levels were associated with formations of uranium-bearing granitic rocks. GAC can effectively reduce radon concentrations in drinking water supplies to very low levels. However, the amount of contact time within the carbon bed required to do so would be prohibitive to many water utilities from an operational and economic standpoint. Further, disposal of the spent GAC as a low-level radioactive waste may be required. Aeration is very effective in the removal of radon from drinking water. Packed tower aerators achieved > 95% reduction in radon concentrations and conventional cascading tray aerators achieved > 75% reduction in radon concentrations. 7 refs., 6 tabs.

  14. The future of oil supply

    PubMed Central

    Miller, Richard G.; Sorrell, Steven R.

    2014-01-01

    Abundant supplies of oil form the foundation of modern industrial economies, but the capacity to maintain and grow global supply is attracting increasing concern. Some commentators forecast a peak in the near future and a subsequent terminal decline in global oil production, while others highlight the recent growth in ‘tight oil’ production and the scope for developing unconventional resources. There are disagreements over the size, cost and recoverability of different resources, the technical and economic potential of different technologies, the contribution of different factors to market trends and the economic implications of reduced supply. Few debates are more important, more contentious, more wide-ranging or more confused. This paper summarizes the main concepts, terms, issues and evidence that are necessary to understand the ‘peak oil’ debate. These include: the origin, nature and classification of oil resources; the trends in oil production and discoveries; the typical production profiles of oil fields, basins and producing regions; the mechanisms underlying those profiles; the extent of depletion of conventional oil; the risk of an approaching peak in global production; and the potential of various mitigation options. The aim is to introduce the subject to non-specialist readers and provide a basis for the subsequent papers in this Theme Issue. PMID:24298085

  15. Mixture of Skewed α-Stable Distributions

    NASA Astrophysics Data System (ADS)

    Shojaei, S. R. Hosseini; Nassiri, V.; Mohammadian, Gh. R.; Mohammadpour, A.

    2011-03-01

    Expectation maximization (EM) algorithm and the Bayesian techniques are two approaches for statistical inference of mixture models [3, 4]. By noting the advantages of the Bayesian methods, practitioners prefer them. However, implementing Markov chain Monte Carlo algorithms can be very complicated for stable distributions, due to the non-analytic density or distribution function formulas. In this paper, we introduce a new class of mixture of heavy-tailed distributions, called mixture of skewed stable distributions. Skewed stable distributions belongs to the exponential family and they have analytic density representation. It is shown that skewed stable distributions dominate skew stable distribution functions and they can be used to model heavy-tailed data. The class of skewed stable distributions has an analytic representation for its density function and the Bayesian inference can be done similar to the exponential family of distributions. Finally, mixture of skewed stable distributions are compared to the mixture of stable distributions through a simulations study.

  16. Supercritical separation process for complex organic mixtures

    DOEpatents

    Chum, H.L.; Filardo, G.

    1990-10-23

    A process is disclosed for separating low molecular weight components from complex aqueous organic mixtures. The process includes preparing a separation solution of supercritical carbon dioxide with an effective amount of an entrainer to modify the solvation power of the supercritical carbon dioxide and extract preselected low molecular weight components. The separation solution is maintained at a temperature of at least about 70 C and a pressure of at least about 1,500 psi. The separation solution is then contacted with the organic mixtures while maintaining the temperature and pressure as above until the mixtures and solution reach equilibrium to extract the preselected low molecular weight components from the organic mixtures. Finally, the entrainer/extracted components portion of the equilibrium mixture is isolated from the separation solution. 1 fig.

  17. Supercritical separation process for complex organic mixtures

    DOEpatents

    Chum, Helena L.; Filardo, Giuseppe

    1990-01-01

    A process is disclosed for separating low molecular weight components from complex aqueous organic mixtures. The process includes preparing a separation solution of supercritical carbon dioxide with an effective amount of an entrainer to modify the solvation power of the supercritical carbon dioxide and extract preselected low molecular weight components. The separation solution is maintained at a temperature of at least about 70.degree. C. and a pressure of at least about 1,500 psi. The separation solution is then contacted with the organic mixtures while maintaining the temperature and pressure as above until the mixtures and solution reach equilibrium to extract the preselected low molecular weight components from the organic mixtures. Finally, the entrainer/extracted components portion of the equilibrium mixture is isolated from the separation solution.

  18. Prediction of viscosity of dense fluid mixtures

    NASA Astrophysics Data System (ADS)

    Royal, Damian D.; Vesovic, Velisa; Trusler, J. P. Martin; Wakeham, William. A.

    The Vesovic-Wakeham (VW) method of predicting the viscosity of dense fluid mixtures has been improved by implementing new mixing rules based on the rigid sphere formalism. The proposed mixing rules are based on both Lebowitz's solution of the Percus-Yevick equation and on the Carnahan-Starling equation. The predictions of the modified VW method have been compared with experimental viscosity data for a number of diverse fluid mixtures: natural gas, hexane + hheptane, hexane + octane, cyclopentane + toluene, and a ternary mixture of hydrofluorocarbons (R32 + R125 + R134a). The results indicate that the proposed improvements make possible the extension of the original VW method to liquid mixtures and to mixtures containing polar species, while retaining its original accuracy.

  19. Cover and startup gas supply system for solid oxide fuel cell generator

    DOEpatents

    Singh, Prabhakar; George, Raymond A.

    1999-01-01

    A cover and startup gas supply system for a solid oxide fuel cell power generator is disclosed. Hydrocarbon fuel, such as natural gas or diesel fuel, and oxygen-containing gas are supplied to a burner. Combustion gas exiting the burner is cooled prior to delivery to the solid oxide fuel cell. The system mixes the combusted hydrocarbon fuel constituents with hydrogen which is preferably stored in solid form to obtain a non-explosive gas mixture. The system may be used to provide both non-explosive cover gas and hydrogen-rich startup gas to the fuel cell.

  20. Cover and startup gas supply system for solid oxide fuel cell generator

    DOEpatents

    Singh, P.; George, R.A.

    1999-07-27

    A cover and startup gas supply system for a solid oxide fuel cell power generator is disclosed. Hydrocarbon fuel, such as natural gas or diesel fuel, and oxygen-containing gas are supplied to a burner. Combustion gas exiting the burner is cooled prior to delivery to the solid oxide fuel cell. The system mixes the combusted hydrocarbon fuel constituents with hydrogen which is preferably stored in solid form to obtain a non-explosive gas mixture. The system may be used to provide both non-explosive cover gas and hydrogen-rich startup gas to the fuel cell. 4 figs.

  1. Coordinated supply chain dynamic production planning model

    NASA Astrophysics Data System (ADS)

    Chandra, Charu; Grabis, Janis

    2001-10-01

    Coordination of different and often contradicting interests of individual supply chain members is one of the important issues in supply chain management because the individual members can not succeed without success of the supply chain and vice versa. This paper investigates a supply chain dynamic production planning problem with emphasis on coordination. A planning problem is formally described using a supply chain kernel, which defines supply chain configuration, management policies, available resources and objectives both at supply chain or macro and supply chain member or micro levels. The coordinated model is solved in order to balance decisions made at the macro and micro levels and members' profitability is used as the coordination criterion. The coordinated model is used to determine inventory levels and production capacity across the supply chain. Application of the coordinated model distributes costs burden uniformly among supply chain members and preserves overall efficiency of the supply chain. Influence of the demand series uncertainty is investigated. The production planning model is a part of the integrated supply chain decision modeling system, which is shared among the supply chain members across the Internet.

  2. Chemical measures of similarity among disinfection by-product mixtures.

    PubMed

    Bull, Richard J; Rice, Glenn; Teuschler, Linda; Feder, Paul

    2009-01-01

    There are few measures that can be used to distinguish among mixtures of disinfection by-products (DBPs) produced in the chlorination or chloramination of drinking water. Objective measures of similarities among DBP mixtures would greatly simplify judgments about the risk that may be associated with exposure to DBPs in a given water supply. Major by-products of chlorination/chloramination include the trihalomethanes (THMs) and haloacetic acids (HAAs), which are routinely measured for compliance to regulations. A key question is whether measurement of similar amounts of these DBPs is indicative of the myriad other DBPs that are known to be produced. This article utilized data from a survey of 35 utilities in the United States that included several additional parameters, including members of the haloacetonitrile, trihaloacetaldehyde, and halopropanone classes. Based upon the distribution of bromine in the THM class, the concentrations of unmeasured brominated and bromochlorinated compounds could be determined. This allowed determination of whether measures of the THM and/or HAA classes reflected the amounts of these less abundant classes. Variations in relative yields among DBP classes were observed with water source type and with whether chlorine or chloramine was used as the disinfectant. However, most of the variability was attributable to geographic location. The relative abundance of brominated by-products also varied among water sources. Recent documentation that potent by-products, such as nitrosamines, are selectively produced in particular water systems and preferentially with chloramination indicates that more measures of individual DBP are needed to evaluate similarity among DBPs mixtures.

  3. Information flow in the pharmaceutical supply chain.

    PubMed

    Yousefi, Nazila; Alibabaei, Ahmad

    2015-01-01

    Managing the supply chain plays an important role in creating competitive advantages for companies. Adequate information flow in supply chain is one of the most important issues in SCM. Therefore, using certain Information Systems can have a significant role in managing and integrating data and information within the supply chain. Pharmaceutical supply chain is more complex than many other supply chains, in the sense that it can affect social and political perspectives. On the other hand, managing the pharmaceutical supply chain is difficult because of its complexity and also government regulations in this field. Although, Iran has progressed a lot in pharmaceutical manufacturing, still there are many unsolved issues in managing the information flow in the pharmaceutical supply chain. In this study, we reviewed the benefits of using different levels of an integrated information system in the supply chain and the possible challenges ahead.

  4. 40 CFR 35.6305 - Obtaining supplies.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ....6325 through 35.6340, and 35.6350. Supplies obtained with Core Program funds must be for non-site-specific purposes. All purchases of supplies under the Core Program must comply with the requirements...

  5. Climate Leadership Award for Supply Chain Leadership

    EPA Pesticide Factsheets

    Apply to the Climate Leadership Award for Supply Chain Leadership, which publicly recognizes organizations that are are at the leading edge of managing greenhouse gas emissions in their organizational supply chains.

  6. Information flow in the pharmaceutical supply chain

    PubMed Central

    Yousefi, Nazila; Alibabaei, Ahmad

    2015-01-01

    Managing the supply chain plays an important role in creating competitive advantages for companies. Adequate information flow in supply chain is one of the most important issues in SCM. Therefore, using certain Information Systems can have a significant role in managing and integrating data and information within the supply chain. Pharmaceutical supply chain is more complex than many other supply chains, in the sense that it can affect social and political perspectives. On the other hand, managing the pharmaceutical supply chain is difficult because of its complexity and also government regulations in this field. Although, Iran has progressed a lot in pharmaceutical manufacturing, still there are many unsolved issues in managing the information flow in the pharmaceutical supply chain. In this study, we reviewed the benefits of using different levels of an integrated information system in the supply chain and the possible challenges ahead. PMID:26664401

  7. Logistics: Supply Based or Distribution Based?

    DTIC Science & Technology

    2007-04-01

    supply chain management, the need to adapt systems as conditions and capabilities change may not be clear or the root causes of problems may not be...logistics-system and supply - chain design and management positions. They need to become adept at integrating the full range of options available to...distribution-based and supply-based designs, the Army, in conjunction with its joint supply - chain partners, should seek optimal, balanced logistics system designs that it can adapt quickly to changing conditions.

  8. Foaming of mixtures of pure hydrocarbons

    NASA Technical Reports Server (NTRS)

    Robinson, J. V.; Woods, W. W.

    1950-01-01

    Mixtures of pure liquid hydrocarbons are capable of foaming. Nine hydrocarbons were mixed in pairs, in all possible combinations, and four proportions of each combination. These mixtures were sealed in glass tubes, and the foaming was tested by shaking. Mixtures of aliphatic with other aliphatic hydrocarbons, or of alkyl benzenes with other alkyl benzenes, did not foam. Mixtures of aliphatic hydrocarbons with alkyl benzenes did foam. The proportions of the mixtures greatly affected the foaming, the maximum foaming of 12 of 20 pairs being at the composition 20 percent aliphatic hydrocarbon, 80 percent alkyl benzene. Six seconds was the maximum foam lifetime of any of these mixtures. Aeroshell 120 lubricating oil was fractionated into 52 fractions and a residue by extraction with acetone in a fractionating extractor. The index of refraction, foam lifetime, color, and viscosity of these fractions were measured. Low viscosity and high index fractions were extracted first. The viscosity of the fractions extracted rose and the index decreased as fractionation proceeded. Foam lifetimes and color were lowest in the middle fractions. Significance is attached to the observation that none of the foam lifetimes of the fractions or residue is as high as the foam lifetime of the original Aeroshell, indicating that the foaming is not due to a particular foaming constituent, but rather to the entire mixture.

  9. A framework for evaluating mixture analysis algorithms

    NASA Astrophysics Data System (ADS)

    Dasaratha, Sridhar; Vignesh, T. S.; Shanmukh, Sarat; Yarra, Malathi; Botonjic-Sehic, Edita; Grassi, James; Boudries, Hacene; Freeman, Ivan; Lee, Young K.; Sutherland, Scott

    2010-04-01

    In recent years, several sensing devices capable of identifying unknown chemical and biological substances have been commercialized. The success of these devices in analyzing real world samples is dependent on the ability of the on-board identification algorithm to de-convolve spectra of substances that are mixtures. To develop effective de-convolution algorithms, it is critical to characterize the relationship between the spectral features of a substance and its probability of detection within a mixture, as these features may be similar to or overlap with other substances in the mixture and in the library. While it has been recognized that these aspects pose challenges to mixture analysis, a systematic effort to quantify spectral characteristics and their impact, is generally lacking. In this paper, we propose metrics that can be used to quantify these spectral features. Some of these metrics, such as a modification of variance inflation factor, are derived from classical statistical measures used in regression diagnostics. We demonstrate that these metrics can be correlated to the accuracy of the substance's identification in a mixture. We also develop a framework for characterizing mixture analysis algorithms, using these metrics. Experimental results are then provided to show the application of this framework to the evaluation of various algorithms, including one that has been developed for a commercial device. The illustration is based on synthetic mixtures that are created from pure component Raman spectra measured on a portable device.

  10. Health Risk Assessment of Chemical Mixtures | Science ...

    EPA Pesticide Factsheets

    The implementation of Superfund requires a methodology for estimating health risk from multi-chemical contamination at ambient levels. Most often, the chemical composition of these mixtures is poorly characterized, exposure data are uncertain and toxicologic data on the known components of the mixture are limited. However, a potential human health hazard may exist and the U.S.EPA, state and local governments need to be able to assess the total hazard in order to make decisions on appropriate action. This report describes a procedure for assessing the risks from chemical mixtures that includes options when different kinds of data are available. Good-quality information on the mixture of concern or a similar mixture should always be used. Less desirable, but still useful approach, is to utilize data on components and their interactions. The quality of exposure and toxicity data must be determined and the uncertainties involved in each risk assessment must be thoroughly discussed. ater contamination is briefly discussed since it is of vital concern as the primary exposure medium for chemical mixtures. The methodology for estimating the human health risk from single chemicals, both carcinogens and systemic toxicants, is reviewed as it forms the basis for the assessment of mixtures. The Implementation of Superfund requires a methodology for estimating health risk from multi-chemical contamination at ambient levels. Most often, the chemical composition of these mix

  11. 7 CFR 1000.6 - Supply plant.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 9 2010-01-01 2009-01-01 true Supply plant. 1000.6 Section 1000.6 Agriculture... Definitions § 1000.6 Supply plant. Supply plant means a plant approved by a duly constituted regulatory agency... diverts fluid milk products to other plants or manufactures dairy products on its premises....

  12. 7 CFR 1000.6 - Supply plant.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 9 2011-01-01 2011-01-01 false Supply plant. 1000.6 Section 1000.6 Agriculture... Definitions § 1000.6 Supply plant. Supply plant means a plant approved by a duly constituted regulatory agency... diverts fluid milk products to other plants or manufactures dairy products on its premises....

  13. 47 CFR 80.1015 - Power supply.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 5 2010-10-01 2010-10-01 false Power supply. 80.1015 Section 80.1015... MARITIME SERVICES Radiotelephone Installations Required by the Bridge-to-Bridge Act § 80.1015 Power supply. (a) There must be readily available for use under normal load conditions, a power supply...

  14. 24 CFR 3280.803 - Power supply.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Power supply. 3280.803 Section 3280... DEVELOPMENT MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARDS Electrical Systems § 3280.803 Power supply. (a) The power supply to the manufactured home shall be a feeder assembly consisting of not more than...

  15. 47 CFR 80.1015 - Power supply.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 47 Telecommunication 5 2013-10-01 2013-10-01 false Power supply. 80.1015 Section 80.1015... MARITIME SERVICES Radiotelephone Installations Required by the Bridge-to-Bridge Act § 80.1015 Power supply. (a) There must be readily available for use under normal load conditions, a power supply...

  16. 47 CFR 80.1015 - Power supply.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 47 Telecommunication 5 2012-10-01 2012-10-01 false Power supply. 80.1015 Section 80.1015... MARITIME SERVICES Radiotelephone Installations Required by the Bridge-to-Bridge Act § 80.1015 Power supply. (a) There must be readily available for use under normal load conditions, a power supply...

  17. 47 CFR 80.1015 - Power supply.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 47 Telecommunication 5 2014-10-01 2014-10-01 false Power supply. 80.1015 Section 80.1015... MARITIME SERVICES Radiotelephone Installations Required by the Bridge-to-Bridge Act § 80.1015 Power supply. (a) There must be readily available for use under normal load conditions, a power supply...

  18. 47 CFR 80.1015 - Power supply.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 47 Telecommunication 5 2011-10-01 2011-10-01 false Power supply. 80.1015 Section 80.1015... MARITIME SERVICES Radiotelephone Installations Required by the Bridge-to-Bridge Act § 80.1015 Power supply. (a) There must be readily available for use under normal load conditions, a power supply...

  19. 21 CFR 1403.33 - Supplies.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 9 2014-04-01 2014-04-01 false Supplies. 1403.33 Section 1403.33 Food and Drugs... supplies exceeding $5,000 in total aggregate fair market value upon termination or completion of the award, and if the supplies are not needed for any other federally sponsored programs or projects, the...

  20. 48 CFR 11.701 - Supply contracts.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 1 2011-10-01 2011-10-01 false Supply contracts. 11.701... DESCRIBING AGENCY NEEDS Variation in Quantity 11.701 Supply contracts. (a) A fixed-price supply contract may... of both; however, contracts for subsistence items may use other applicable terms of variation...

  1. Supply Chain Management in Humanitarian Relief Logistics

    DTIC Science & Technology

    2004-03-01

    Hundreds of millions of people are affected by disasters each year. This thesis explores the use of supply chain management techniques to overcome...academic, organizational, and contemporary literature. Possible solutions to these barriers were selected from available supply chain management...literature. This work is different from others in that it marries supply chain principles from different disciplines (including private, nonprofit, and

  2. 7 CFR 1000.6 - Supply plant.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 9 2013-01-01 2013-01-01 false Supply plant. 1000.6 Section 1000.6 Agriculture... Definitions § 1000.6 Supply plant. Supply plant means a plant approved by a duly constituted regulatory agency... diverts fluid milk products to other plants or manufactures dairy products on its premises....

  3. 7 CFR 1000.6 - Supply plant.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 9 2014-01-01 2013-01-01 true Supply plant. 1000.6 Section 1000.6 Agriculture... Definitions § 1000.6 Supply plant. Supply plant means a plant approved by a duly constituted regulatory agency... diverts fluid milk products to other plants or manufactures dairy products on its premises....

  4. 7 CFR 1000.6 - Supply plant.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 9 2012-01-01 2012-01-01 false Supply plant. 1000.6 Section 1000.6 Agriculture... Definitions § 1000.6 Supply plant. Supply plant means a plant approved by a duly constituted regulatory agency... diverts fluid milk products to other plants or manufactures dairy products on its premises....

  5. Learning to Integrate: Supply Chains Reconceptualised

    ERIC Educational Resources Information Center

    Sense, Andrew J.; Clements, Michael D. J.

    2007-01-01

    This paper introduces and explains a conception of supply chains from a situated learning perspective. This non-conventional supply chain perspective invites the reader to consider supply chain scenarios as "situated learning opportunities involving multiple communities of practice" interacting and participating together. It is argued that by…

  6. Visualisation for System Learning in Supply Chains

    ERIC Educational Resources Information Center

    Lindskog, Magnus; Abrahamsson, Mats; Aronsson, Hakan

    2007-01-01

    Contemporary supply chains are vastly complex, and decisions made by actors have system-wide consequences that these might not be able to foresee. There are gaps between "best practice"-founded theory and actual practice in supply chains. To remedy this, we argue, the supply chain actors need to enhance systems knowledge. There is a need to…

  7. 25 CFR 137.1 - Water supply.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 25 Indians 1 2011-04-01 2011-04-01 false Water supply. 137.1 Section 137.1 Indians BUREAU OF... CARLOS INDIAN IRRIGATION PROJECT, ARIZONA § 137.1 Water supply. The engineering report dealt with in... capacity of the San Carlos reservoir created by the Coolidge Dam and the water supply therefor over...

  8. 25 CFR 137.1 - Water supply.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 25 Indians 1 2013-04-01 2013-04-01 false Water supply. 137.1 Section 137.1 Indians BUREAU OF... CARLOS INDIAN IRRIGATION PROJECT, ARIZONA § 137.1 Water supply. The engineering report dealt with in... capacity of the San Carlos reservoir created by the Coolidge Dam and the water supply therefor over...

  9. 20 CFR 654.405 - Water supply.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 20 Employees' Benefits 3 2013-04-01 2013-04-01 false Water supply. 654.405 Section 654.405... THE EMPLOYMENT SERVICE SYSTEM Housing for Agricultural Workers Housing Standards § 654.405 Water supply. (a) An adequate and convenient supply of water that meets the standards of the State...

  10. 25 CFR 137.1 - Water supply.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 25 Indians 1 2014-04-01 2014-04-01 false Water supply. 137.1 Section 137.1 Indians BUREAU OF... CARLOS INDIAN IRRIGATION PROJECT, ARIZONA § 137.1 Water supply. The engineering report dealt with in... capacity of the San Carlos reservoir created by the Coolidge Dam and the water supply therefor over...

  11. 20 CFR 654.405 - Water supply.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 20 Employees' Benefits 3 2011-04-01 2011-04-01 false Water supply. 654.405 Section 654.405... THE EMPLOYMENT SERVICE SYSTEM Housing for Agricultural Workers Housing Standards § 654.405 Water supply. (a) An adequate and convenient supply of water that meets the standards of the State...

  12. 9 CFR 354.224 - Water supply.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 9 Animals and Animal Products 2 2014-01-01 2014-01-01 false Water supply. 354.224 Section 354.224....224 Water supply. The water supply shall be ample, clean, and potable with adequate facilities for its distribution in the plant and its protection against contamination and pollution. (a) Hot water at...

  13. 24 CFR 3285.603 - Water supply.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Water supply. 3285.603 Section 3285... § 3285.603 Water supply. (a) Crossover. Multi-section homes with plumbing in both sections require water... pressure and reduction. When the local water supply pressure exceeds 80 psi to the manufactured home,...

  14. 9 CFR 354.224 - Water supply.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 9 Animals and Animal Products 2 2013-01-01 2013-01-01 false Water supply. 354.224 Section 354.224....224 Water supply. The water supply shall be ample, clean, and potable with adequate facilities for its distribution in the plant and its protection against contamination and pollution. (a) Hot water at...

  15. 25 CFR 137.1 - Water supply.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false Water supply. 137.1 Section 137.1 Indians BUREAU OF... CARLOS INDIAN IRRIGATION PROJECT, ARIZONA § 137.1 Water supply. The engineering report dealt with in... capacity of the San Carlos reservoir created by the Coolidge Dam and the water supply therefor over...

  16. 20 CFR 654.405 - Water supply.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 20 Employees' Benefits 3 2014-04-01 2014-04-01 false Water supply. 654.405 Section 654.405... THE EMPLOYMENT SERVICE SYSTEM Housing for Agricultural Workers Housing Standards § 654.405 Water supply. (a) An adequate and convenient supply of water that meets the standards of the State...

  17. 24 CFR 3285.603 - Water supply.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 24 Housing and Urban Development 5 2012-04-01 2012-04-01 false Water supply. 3285.603 Section 3285... § 3285.603 Water supply. (a) Crossover. Multi-section homes with plumbing in both sections require water... pressure and reduction. When the local water supply pressure exceeds 80 psi to the manufactured home,...

  18. 20 CFR 654.405 - Water supply.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 20 Employees' Benefits 3 2010-04-01 2010-04-01 false Water supply. 654.405 Section 654.405... THE EMPLOYMENT SERVICE SYSTEM Housing for Agricultural Workers Housing Standards § 654.405 Water supply. (a) An adequate and convenient supply of water that meets the standards of the State...

  19. 24 CFR 3285.603 - Water supply.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 24 Housing and Urban Development 5 2014-04-01 2014-04-01 false Water supply. 3285.603 Section 3285... § 3285.603 Water supply. (a) Crossover. Multi-section homes with plumbing in both sections require water... pressure and reduction. When the local water supply pressure exceeds 80 psi to the manufactured home,...

  20. 9 CFR 354.224 - Water supply.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Water supply. 354.224 Section 354.224....224 Water supply. The water supply shall be ample, clean, and potable with adequate facilities for its distribution in the plant and its protection against contamination and pollution. (a) Hot water at...

  1. 25 CFR 137.1 - Water supply.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 25 Indians 1 2012-04-01 2011-04-01 true Water supply. 137.1 Section 137.1 Indians BUREAU OF INDIAN... INDIAN IRRIGATION PROJECT, ARIZONA § 137.1 Water supply. The engineering report dealt with in section 1... of the San Carlos reservoir created by the Coolidge Dam and the water supply therefor over a...

  2. 24 CFR 3285.603 - Water supply.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 24 Housing and Urban Development 5 2011-04-01 2011-04-01 false Water supply. 3285.603 Section 3285... § 3285.603 Water supply. (a) Crossover. Multi-section homes with plumbing in both sections require water... pressure and reduction. When the local water supply pressure exceeds 80 psi to the manufactured home,...

  3. 9 CFR 354.224 - Water supply.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 9 Animals and Animal Products 2 2012-01-01 2012-01-01 false Water supply. 354.224 Section 354.224....224 Water supply. The water supply shall be ample, clean, and potable with adequate facilities for its distribution in the plant and its protection against contamination and pollution. (a) Hot water at...

  4. 20 CFR 654.405 - Water supply.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 20 Employees' Benefits 3 2012-04-01 2012-04-01 false Water supply. 654.405 Section 654.405... THE EMPLOYMENT SERVICE SYSTEM Housing for Agricultural Workers Housing Standards § 654.405 Water supply. (a) An adequate and convenient supply of water that meets the standards of the State...

  5. 24 CFR 3285.603 - Water supply.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 24 Housing and Urban Development 5 2013-04-01 2013-04-01 false Water supply. 3285.603 Section 3285... § 3285.603 Water supply. (a) Crossover. Multi-section homes with plumbing in both sections require water... pressure and reduction. When the local water supply pressure exceeds 80 psi to the manufactured home,...

  6. 9 CFR 354.224 - Water supply.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 9 Animals and Animal Products 2 2011-01-01 2011-01-01 false Water supply. 354.224 Section 354.224....224 Water supply. The water supply shall be ample, clean, and potable with adequate facilities for its distribution in the plant and its protection against contamination and pollution. (a) Hot water at...

  7. 32 CFR 34.24 - Supplies.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 32 National Defense 1 2011-07-01 2011-07-01 false Supplies. 34.24 Section 34.24 National Defense... § 34.24 Supplies. (a) Title shall vest in the recipient upon acquisition for supplies acquired with... shall retain the items for use on non-Federal sponsored activities or sell them, but shall, in...

  8. 32 CFR 34.24 - Supplies.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 32 National Defense 1 2010-07-01 2010-07-01 false Supplies. 34.24 Section 34.24 National Defense... § 34.24 Supplies. (a) Title shall vest in the recipient upon acquisition for supplies acquired with... shall retain the items for use on non-Federal sponsored activities or sell them, but shall, in...

  9. Rare resource supply crisis and solution technology for semiconductor manufacturing

    NASA Astrophysics Data System (ADS)

    Fukuda, Hitomi; Hu, Sophia; Yoo, Youngsun; Takahisa, Kenji; Enami, Tatsuo

    2016-03-01

    There are growing concerns over future environmental impact and earth resource shortage throughout the world and in many industries. Our semiconductor industry is not excluded. "Green" has become an important topic as production volume become larger and more powerful. Especially, the rare gases are widely used in semiconductor manufacturing because of its inertness and extreme chemical stability. One major component of an Excimer laser system is Neon. It is used as a buffer gas for Argon (Ar) and Krypton (Kr) gases used in deep ultraviolet (DUV) lithography laser systems. Since Neon gas accounting for more than 96% of the laser gas mixture, a fairly large amount of neon gas is consumed to run these DUV lasers. However, due to country's instability both in politics and economics in Ukraine, the main producer of neon gas today, supply reduction has become an issue and is causing increasing concern. This concern is not only based on price increases, but has escalated to the point of supply shortages in 2015. This poses a critical situation for the semiconductor industry, which represents the leading consumer of neon gas in the world. Helium is another noble gas used for Excimer laser operation. It is used as a purge gas for optical component modules to prevent from being damaged by active gases and impurities. Helium has been used in various industries, including for medical equipment, linear motor cars, and semiconductors, and is indispensable for modern life. But consumption of helium in manufacturing has been increased dramatically, and its unstable supply and price rise has been a serious issue today. In this article, recent global supply issue of rare resources, especially Neon gas and Helium gas, and its solution technology to support semiconductor industry will be discussed.

  10. Estrogenic activity of UV filter mixtures.

    PubMed

    Kunz, Petra Y; Fent, Karl

    2006-11-15

    UV-absorbing chemicals (UV filters) are widely used for protection against UV radiation in sunscreens and in a variety of cosmetic products and materials. Depending on the breadth and factor of UV protection, they are added as single compounds or as a combination thereof. Some UV filters have estrogenic activity, but their activity and interactions in mixtures are largely unknown. In this work, we analyzed 8 commonly used UV filters, which are pure or partial hERalpha agonists, for their estrogenic activity in equieffective mixtures in a recombinant yeast assay carrying the human estrogen receptor alpha (hERalpha). Mixtures of two, four and eight UV filters alone, or in combination with 17 beta estradiol (E2), were assessed at different effect levels and no-observed-effect-concentrations (NOEC). Predictions of the joint effects of these mixtures were calculated by employing the concentration addition (CA) and independent action (IA) model. Most binary mixtures comprising of pure hERalpha agonists showed a synergistic activity at all mixture combinations. Only in combination with benzophenone-1, antagonistic activity was observed at some effect levels. All mixtures of four or eight, pure or pure and partial hERalpha agonists, alone or including E2, showed synergistic activity at concentrations giving an increase of 10% of basal activity (BC10). This occurred even at concentrations that were at the NOEC level of each single compound. Hence, there were substantial mixture effects even though each UV filter was present at its NOEC level. These results show that significant interactions occur in UV filter mixtures, which is important for the hazard and risk assessments of these personal care products.

  11. Estrogenic activity of UV filter mixtures

    SciTech Connect

    Kunz, Petra Y. . E-mail: petra.kunz@fhnw.ch; Fent, Karl . E-mail: karl.fent@bluewin.ch

    2006-11-15

    UV-absorbing chemicals (UV filters) are widely used for protection against UV radiation in sunscreens and in a variety of cosmetic products and materials. Depending on the breadth and factor of UV protection, they are added as single compounds or as a combination thereof. Some UV filters have estrogenic activity, but their activity and interactions in mixtures are largely unknown. In this work, we analyzed 8 commonly used UV filters, which are pure or partial hER{alpha} agonists, for their estrogenic activity in equieffective mixtures in a recombinant yeast assay carrying the human estrogen receptor alpha (hER{alpha}). Mixtures of two, four and eight UV filters alone, or in combination with 17 {beta} estradiol (E2), were assessed at different effect levels and no-observed-effect-concentrations (NOEC). Predictions of the joint effects of these mixtures were calculated by employing the concentration addition (Canada) and independent action (IA) model. Most binary mixtures comprising of pure hER{alpha} agonists showed a synergistic activity at all mixture combinations. Only in combination with benzophenone-1, antagonistic activity was observed at some effect levels. All mixtures of four or eight, pure or pure and partial hER{alpha} agonists, alone or including E2, showed synergistic activity at concentrations giving an increase of 10% of basal activity (BC10). This occurred even at concentrations that were at the NOEC level of each single compound. Hence, there were substantial mixture effects even though each UV filter was present at its NOEC level. These results show that significant interactions occur in UV filter mixtures, which is important for the hazard and risk assessments of these personal care products.

  12. Strategic materials availability and supply

    NASA Technical Reports Server (NTRS)

    Stephens, Joseph R.

    1989-01-01

    An evaluation is made of the supply sources and current availability of elements involved in superalloy compositions, as well as of development trends in the substitution of strategic materials for superalloys, giving attention to the results thus far achieved by NASA's Conservation of Strategic Aerospace Materials program, which formally operated only from 1980 to 1984 but whose various research initiatives have been continued under other NASA programs. Peacetime and wartime economies' need and probable availability analyses are presented for bauxite/aluminum, the Pt-group metals, and the alloying elements Mn, Nb, Ta, Co, Cr, Ni, W, Fe, Cu, Ti, Mo, and Mg.

  13. Petroleum supply monthly: December 1993

    SciTech Connect

    Not Available

    1993-12-01

    Data are presented which describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States. Data are presented in two sections: Summary Statistics, presenting a time series of selected petroleum data on a U.S. level, and Detailed Statistics, presenting statistics for the most current month available as well as year to date.

  14. Nearly Azeotropic Mixtures To Replace Refrigerant 12

    NASA Technical Reports Server (NTRS)

    Jones, Jack A.

    1992-01-01

    Number of nearly azeotropic fluid mixtures have saturation pressures similar to Refrigerant 12 while being about 2 percent as damaging to ozone layer. Five mixtures of R134a, R152a, R124, and R142b have low boiling-point spreads, low toxicity, and low ozone-damaging capability, are nonflammable, and more compatible with conventional oils than R134a. Pressure of combinations nearly equal to R12, and mixtures may be good "drop-in substitutes". Overall composition not altered by leakage. Usable in commercial, automotive, and household refrigerators and air conditioners.

  15. Quantitative NIR Raman analysis in liquid mixtures.

    PubMed

    Sato-Berrú, R Ysacc; Medina-Valtierra, Jorge; Medina-Gutiérrez, Cirilo; Frausto-Reyes, Claudio

    2004-08-01

    The capability to obtain quantitative information of a simple way from Raman spectra is a subject of considerable interest. In this work, this is demonstrated for mixtures of ethanol with water and rhodamine-6G (R-6G) with methanol, which were analyzed directly in glass vessel. The Raman intensities and a simple mathematical model have been used and applied for the analysis of liquid samples. It is starting point to generate a general expression, from the experimental spectra, as the sum of the particular expression for each pure compound allow us to obtain an expression for the mixtures which can be used for determining concentrations, from the Raman spectrum, of the mixture.

  16. APPARATUS FOR HANDLING MIXTURES OF SOLID MATERIALS

    DOEpatents

    Hubbell, J.P.

    1959-08-25

    An apparatus is described for handling either a mixture of finely subdivided materials or a single material requiring a compacting action thereon preparatory to a chemical reducing process carried out in a crucible container. The apparatus is designed to deposit a mixture of dust-forming solid materials in a container while confining the materials against escape into the surrounding atmosphere. A movable filling tube, having a compacting member, is connected to the container and to a covered hopper receiving the mixture of materials. The filling tube is capable of reciprocating in the container and their relative positions are dependent upon the pressure established upon the material by the compacting member.

  17. Nucleate pool boiling of hydrocarbon mixtures

    SciTech Connect

    Sardesai, R.G.; Palen, J.W.; Thome, J.

    1986-01-01

    The Schlunder method can be correctly used to predict boiling heat transfer coefficient of multicomponent hydrocarbon mixtures. The method was tested against experimental mixtures containing up to five components. The Stephan-Abdelsalam correlation can be used to calculate a ''pseudo-single component'' boiling heat transfer coefficient for a mixture using weighted properties. The effective temperature driving force term and the high mass flux correction term in the Schlunder formulation are empirically adjusted to improve the accuracy of prediction. Predictions of the Schlunder method are sensitive to the VLE calculations. The UNIFAC method is used in this study for reasons discussed in the paper.

  18. Power-supply regulation by microprocessor

    SciTech Connect

    Sheehan, J.; Langenbach, H.

    1983-01-01

    Many small-magnet power supplies are regulated by using a microprocessor system to generate control voltages to continuously servoregulate each power supply. The power supplies are of very simple design since all regulation and feedback hardware are parts of the microprocessor system. Most of the supplies are bipolar transistor followers, powered by a common unregulated dc power supply and are used to power trim steering magnets on the three NSLS synchrotron rings. Twelve-bit accuracy is obtained using commercially available microprocessor pc cards.

  19. International labor migration and domestic labor supply.

    PubMed

    Kochhar, R

    1992-04-01

    "This paper constructs a dynamic, general equilibrium framework to study the relationship between international labor migration and domestic labor supply. The general equilibrium nature of the model enables us to endogenize the pattern of labor migration. The effect of labor migration on domestic wage rates and labor supply is shown to depend on the pattern of labor migration. If the substitution effect dominates the income effect in labor supply, the domestic supply of labor necessarily decreases in response to an inflow of migrants....Similarly, if the dominant effect is the income effect, the immigration of labor necessarily increases the domestic supply of labor."

  20. A new bipolar Qtrim power supply system

    SciTech Connect

    Mi, C.; Bruno, D.; Drozd, J.; Nolan, T.; Orsatti, F.; Heppener, G.; Di Lieto, A.; Schultheiss, C.; Samms, T.; Zapasek, R.; Sandberg, J.

    2015-05-03

    This year marks the 15th run of RHIC (Relativistic Heavy Ion Collider) operations. The reliability of superconducting magnet power supplies is one of the essential factors in the entire accelerator complex. Besides maintaining existing power supplies and their associated equipment, newly designed systems are also required based on the physicist’s latest requirements. A bipolar power supply was required for this year’s main quadruple trim power supply. This paper will explain the design, prototype, testing, installation and operation of this recently installed power supply system.

  1. Superalloy resources: Supply and availability

    NASA Technical Reports Server (NTRS)

    Stephens, Joseph R.

    1987-01-01

    Over the past several decades there have been shortages of strategic materials because of our near total import dependence on such metals as chromium, cobalt, and tantalum. In response to the continued vulnerability of U.S. superalloy producers to disruptions in resource supplies, NASA has undertaken a program to address alternatives to the super-alloys containing significant quantities of the strategic materials such as chromium, cobalt, niobium, and tantalum. The research program called Conservation of Strategic Aerospace Materials (COSAM) focuses on substitution, processing, and alternate materials to achieve its goals. In addition to NASA Lewis Research Center, universities and industry play an important role in the COSAM Program. This paper defines what is meant by strategic materials in the aerospace community, presents a strategic materials index, and reviews the resource supply and availability picture from the U.S. point of view. In addition, research results from the COSAM Program are highlighted and future directions for the use of low strategic material alloys or alternate materials are discussed.

  2. Natural Gas Supply SBIR Program

    SciTech Connect

    Shoemaker, H.D.; Gwilliam, W.J.

    1995-07-01

    The Small Business Innovation Research (SBIR) program was created in 1982 by Public Law 97-219 and reauthorized in 1992 until the year 2000 by Public Law 102-564. The purposes of the new law are to (1) expand and improve the SBIR program, 2) emphasize the program`s goal of increasing private sector commercialization of technology developed through Federal R&D, (3) increase small business participation in Federal R&D, and (4) improve the Federal Government`s dissemination of information concerning the SBIR program. DOE`s SBIR pro-ram has two features that are unique. In the 1995 DOE SBIR solicitation, the DOE Fossil Energy topics were: environmental technology for natural gas, oil, and coal; advanced recovery of oil; natural gas supply; natural gas utilization; advanced coal-based power systems; and advanced fossil fuels research. The subtopics for this solicitation`s Natural Gas Supply topic are (1) drilling, completion, and stimulation; (2) low-permeability Formations; (3) delivery and storage; and (4) natural gas upgrading.

  3. Mars sample return power supply

    NASA Technical Reports Server (NTRS)

    Hoang, Don; Ludwigs, Sharon; Schmitz, Paul; Wright, John

    1988-01-01

    A power supply is designed for a vehicle able to operate on the surface of Mars for a period of 5 to 10 years. This vehicle will be used for sample and data collection. The design is based on the assumption that the vehicle will be unmanned. Also, there will be no means by which components could be repaired or replaced while on the Martian surface. A consequence of this is that all equipment must meet high standards of reliability and, if possible, redundancy. Power will be supplied to the vehicle by means of a General Purpose Heat Source capable of producing a minimum of 7 kW of thermal power. The heat generated from the General Purpose Heat Source will be transferred to a Stirling engine via hot side heat pipes. The Stirling engine will then convert this heat into 2 kW of electrical power. Cold side heat pipes will be used to carry away waste heat, which will be released to the Martian environment via radiators connected to the end of the cold side heat pipes.

  4. Mars sample return power supply

    NASA Astrophysics Data System (ADS)

    Hoang, Don; Ludwigs, Sharon; Schmitz, Paul; Wright, John

    A power supply is designed for a vehicle able to operate on the surface of Mars for a period of 5 to 10 years. This vehicle will be used for sample and data collection. The design is based on the assumption that the vehicle will be unmanned. Also, there will be no means by which components could be repaired or replaced while on the Martian surface. A consequence of this is that all equipment must meet high standards of reliability and, if possible, redundancy. Power will be supplied to the vehicle by means of a General Purpose Heat Source capable of producing a minimum of 7 kW of thermal power. The heat generated from the General Purpose Heat Source will be transferred to a Stirling engine via hot side heat pipes. The Stirling engine will then convert this heat into 2 kW of electrical power. Cold side heat pipes will be used to carry away waste heat, which will be released to the Martian environment via radiators connected to the end of the cold side heat pipes.

  5. Transcriptional responses to complex mixtures - A review

    EPA Science Inventory

    Exposure of people to hazardous compounds is primarily through complex environmental mixtures, those that occur through media such as air, soil, water, food, cigarette smoke, and combustion emissions. Microarray technology offers the ability to query the entire genome after expos...

  6. Predicting skin permeability from complex chemical mixtures

    SciTech Connect

    Riviere, Jim E. . E-mail: Jim_Riviere@ncsu.edu; Brooks, James D.

    2005-10-15

    Occupational and environmental exposure to topical chemicals is usually in the form of complex chemical mixtures, yet risk assessment is based on experimentally derived data from individual chemical exposures from a single, usually aqueous vehicle, or from computed physiochemical properties. We present an approach using hybrid quantitative structure permeation relationships (QSPeR) models where absorption through porcine skin flow-through diffusion cells is well predicted using a QSPeR model describing the individual penetrants, coupled with a mixture factor (MF) that accounts for physicochemical properties of the vehicle/mixture components. The baseline equation is log k {sub p} = c + mMF + a{sigma}{alpha} {sub 2} {sup H} + b{sigma}{beta} {sub 2} {sup H} + s{pi} {sub 2} {sup H} + rR {sub 2} + vV {sub x} where {sigma}{alpha} {sub 2} {sup H} is the hydrogen-bond donor acidity, {sigma}{beta} {sub 2} {sup H} is the hydrogen-bond acceptor basicity, {pi} {sub 2} {sup H} is the dipolarity/polarizability, R {sub 2} represents the excess molar refractivity, and V {sub x} is the McGowan volume of the penetrants of interest; c, m, a, b, s, r, and v are strength coefficients coupling these descriptors to skin permeability (k {sub p}) of 12 penetrants (atrazine, chlorpyrifos, ethylparathion, fenthion, methylparathion, nonylphenol, {rho}-nitrophenol, pentachlorophenol, phenol, propazine, simazine, and triazine) in 24 mixtures. Mixtures consisted of full factorial combinations of vehicles (water, ethanol, propylene glycol) and additives (sodium lauryl sulfate, methyl nicotinate). An additional set of 4 penetrants (DEET, SDS, permethrin, ricinoleic acid) in different mixtures were included to assess applicability of this approach. This resulted in a dataset of 16 compounds administered in 344 treatment combinations. Across all exposures with no MF, R{sup 2} for absorption was 0.62. With the MF, correlations increased up to 0.78. Parameters correlated to the MF include refractive

  7. Flash evaporation of liquid monomer particle mixture

    DOEpatents

    Affinito, J.D.; Darab, J.G.; Gross, M.E.

    1999-05-11

    The present invention is a method of making a first solid composite polymer layer. The method has the steps of (a) mixing a liquid monomer with particles substantially insoluble in the liquid monomer forming a monomer particle mixture; (b) flash evaporating the particle mixture and forming a composite vapor; and (c) continuously cryocondensing said composite vapor on a cool substrate and cross-linking the cryocondensed film thereby forming the polymer layer. 3 figs.

  8. Flash evaporation of liquid monomer particle mixture

    DOEpatents

    Affinito, John D.; Darab, John G.; Gross, Mark E.

    1999-01-01

    The present invention is a method of making a first solid composite polymer layer. The method has the steps of (a) mixing a liquid monomer with particles substantially insoluble in the liquid monomer forming a monomer particle mixture; (b) flash evaporating the particle mixture and forming a composite vapor; and (c) continuously cryocondensing said composite vapor on a cool substrate and cross-linking the cryocondensed film thereby forming the polymer layer.

  9. Diffusion method of seperating gaseous mixtures

    DOEpatents

    Pontius, Rex B.

    1976-01-01

    A method of effecting a relatively large change in the relative concentrations of the components of a gaseous mixture by diffusion which comprises separating the mixture into heavier and lighter portions according to major fraction mass recycle procedure, further separating the heavier portions into still heavier subportions according to a major fraction mass recycle procedure, and further separating the lighter portions into still lighter subportions according to a major fraction equilibrium recycle procedure.

  10. The triple-A supply chain.

    PubMed

    Lee, Hau L

    2004-10-01

    Building a strong supply chain is essential for business success. But when it comes to improving their supply chains, few companies take the right approach. Many businesses work to make their chains faster or more cost-effective, assuming that those steps are the keys to competitive advantage. To the contrary: Supply chains that focus on speed and costs tend to deteriorate over time. The author has spent 15 years studying more than 60 companies to gain insight into this and other supply chain dilemmas. His conclusion: Only companies that build supply chains that are agile, adaptable, and aligned get ahead of their rivals. All three components are essential; without any one of them, supply chains break down. Great companies create supply chains that respond to abrupt changes in markets. Agility is critical because in most industries, both demand and supply fluctuate rapidly and widely. Supply chains typically cope by playing speed against costs, but agile ones respond both quickly and cost-efficiently. Great companies also adapt their supply networks when markets or strategies change. The best supply chains allow managers to identify structural shifts early by recording the latest data, filtering out noise, and tracking key patterns. Finally, great companies align the interests of the partners in their supply chains with their own. That's important because every firm is concerned solely with its own interests. If its goals are out of alignment with those of other partners in the supply chain, performance will suffer. When companies hear about the triple-A supply chain, they assume that building one will require increased technology and investment. But most firms already have the infrastructure in place to create one. A fresh attitude alone can go a long way toward making it happen.

  11. Phase equilibria for complex fluid mixtures

    SciTech Connect

    Prausnitz, J.M.

    1983-04-01

    After defining complex mixtures, attention is given to the canonical procedure used for the thermodynamics of fluid mixtures: first, we establish a suitable, idealized reference system and then we establish a perturbation (or excess function) which corrects the idealized system for real behavior. For complex mixtures containing identified components (e.g. alcohols, ketones, water) discussion is directed at possible techniques for extending to complex mixtures our conventional experience with reference systems and perturbations for simple mixtures. Possible extensions include generalization of the quasi-chemical approximation (local compositions) and superposition of chemical equilibria (association and solvation) on a physical equation of state. For complex mixtures containing unidentified components (e.g. coal-derived fluids), a possible experimental method is suggested for characterization; conventional procedures can then be used to calculate phase equilibria using the concept of pseudocomponents whose properties are given by the characterization data. Finally, as an alternative to the pseudocomponent method, a brief introduction is given to phase-equilibrium calculations using continuous thermodynamics.

  12. Toxicity evaluation of PAH mixtures using Microtox

    SciTech Connect

    Thompkins, J.; Guthrie, E.; Pfaender, F.

    1995-12-31

    Polycyclic aromatic hydrocarbons (PAH) are produced from both natural and anthropogenic combustion processes. PAHs are known to be toxic and carcinogenic, are prevalent at many hazardous waste sites, and pose a potential risk to both ecological and human health. To date, few researchers have assessed the toxicity of polycyclic aromatic hydrocarbon (PAH) mixtures. The toxicity of chrysene, anthracene, pyrene, phenanthrene, fluoranthrene, acenaphthene, fluorene, and naphthalene were evaluated using Microtox, and acute toxicity assay that uses bioluminescent bacteria, Photobacterium phosphoreum, to measure toxicity. In this study, the toxicities of 2, 3, and 4 ring PAHs were determined for individual compounds. Synergistic or additive effects of PAH mixtures was assessed by comparing the toxicity of mixtures with that of pure compounds. Each PAH or mixture was evaluated at their respective water solubility concentrations, For individual PAHs tested, the toxicity of PAHs is inversely related to water solubility. Mixtures of two and three PAHs with disparate water solubilities resulted in synergistic interactions. Antagonistic interactions, a decrease in toxicity, were observed for mixtures of similar water solubilities.

  13. Novel anisole mixture and gasoline containing the same

    DOEpatents

    Singerman, Gary M.

    1982-01-26

    A novel anisole mixture containing anisole and a mixture of alkyl anisoles and liquid hydrocarbon fuels containing said novel anisole mixture in an amount sufficient to increase the octane number of said liquid fuel composition.

  14. Bayesian source separation with mixture of Gaussians prior for sources and Gaussian prior for mixture coefficients

    NASA Astrophysics Data System (ADS)

    Snoussi, Hichem; Mohammad-Djafari, Ali

    2001-05-01

    In this contribution, we present new algorithms to source separation for the case of noisy instantaneous linear mixture, within the Bayesian statistical framework. The source distribution prior is modeled by a mixture of Gaussians [1] and the mixing matrix elements distributions by a Gaussian [2]. We model the mixture of Gaussians hierarchically by mean of hidden variables representing the labels of the mixture. Then, we consider the joint a posteriori distribution of sources, mixing matrix elements, labels of the mixture and other parameters of the mixture with appropriate prior probability laws to eliminate degeneracy of the likelihood function of variance parameters and we propose two iterative algorithms to estimate jointly sources, mixing matrix and hyperparameters: Joint MAP (Maximum a posteriori) algorithm and penalized EM algorithm. The illustrative example is taken in [3] to compare with other algorithms proposed in literature. .

  15. Stand by electrical supply source

    SciTech Connect

    Mucsy, E.; Hoos, K.

    1985-06-25

    A stand-by electrical energy source for equipment to be operated with substantially continuous current supply, comprising three components one of which is at least one electric rotary machine, another of which is a flywheel and the third of which is an auxiliary energy source. Planetary gearing is provided, comprising a central shaft on which is mounted a sun gear, a planet gear and a ring gear, each of the three components being connected with a respective one of these gears. Two of the three components are interconnected by a drive with an infinitely variable transmission. In one embodiment, the electric rotary machine is connected to the planet gear, the flywheel is connected to the sun gear and the auxiliary energy source is connected with the ring gear. In another embodiment, the electric rotary machine is connected to the sun gear, the flywheel is connected to the ring gear, and the auxiliary energy source is connected to the planet gear.

  16. Uninterruptible power supply (UPS) systems

    SciTech Connect

    1997-04-01

    Use of this purchase specification is not mandatory. User should review the document and determine if it meets the user`s purpose. This document contains a fill-in-the-blanks guide specification for the procurement of uninterruptible power supply (UPS) systems greater than 10 kVA, organized as follows: Parts 1 through 7--technical requirements; Appendix A--technical requirements to be included in the proposal; Appendix B--UPS system data sheets to be completed by each bidder (Seller) and submitted with the proposal; Appendix C--general guidelines giving the specifier parameters for selecting a UPS system; it should be read before preparing an actual specification, and is not attached to the specification; Attachment 1--sketches prepared by the purchaser (Owner); Attachment 2--sample title page.

  17. Food supply reliance on groundwater

    NASA Astrophysics Data System (ADS)

    Dalin, Carole; Puma, Michael; Wada, Yoshihide; Kastner, Thomas

    2016-04-01

    Water resources, essential to sustain human life, livelihoods and ecosystems, are under increasing pressure from population growth, socio-economic development and global climate change. As the largest freshwater resource on Earth, groundwater is key for human development and food security. Yet, excessive abstraction of groundwater for irrigation, driven by an increasing demand for food in recent decades, is leading to fast exhaustion of groundwater reserves in major agricultural areas of the world. Some of the highest depletion rates are observed in Pakistan, India, California Central Valley and the North China Plain aquifers. In addition, the growing economy and population of several countries, such as India and China, makes prospects of future available water and food worrisome. In this context, it is becoming particularly challenging to sustainably feed the world population, without exhausting our water resources. Besides, food production and consumption across the globe have become increasingly interconnected, with many areas' agricultural production destined to remote consumers. In this globalisation era, trade is crucial to the world's food system. As a transfer of water-intensive goods, across regions with varying levels of water productivity, food trade can save significant volumes of water resources globally. This situation makes it essential to address the issue of groundwater overuse for global food supply, accounting for international food trade. To do so, we quantify the current, global use of non-renewable groundwater for major crops, accounting for various water productivity and trade flows. This will highlight areas requiring quickest attention, exposing major exporters and importers of non-renewable groundwater, and thus help explore solutions to improve the sustainability of global food supply.

  18. Nevada test site water-supply wells

    SciTech Connect

    Gillespie, D.; Donithan, D.; Seaber, P.

    1996-05-01

    A total of 15 water-supply wells are currently being used at the Nevada Test Site (NTS). The purpose of this report is to bring together the information gleaned from investigations of these water-supply wells. This report should serve as a reference on well construction and completion, static water levels, lithologic and hydrologic characteristics of aquifers penetrated, and general water quality of water-supply wells at the NTS. Possible sources for contamination of the water-supply wells are also evaluated. Existing wells and underground nuclear tests conducted near (within 25 meters (m)) or below the water table within 2 kilometers (km) of a water-supply were located and their hydrogeologic relationship to the water-supply well determined.

  19. Upgrading the TFTR Transrex Power Supplies

    SciTech Connect

    J. E. Lawson, R. Marsala, S. Ramakrishnan, X. Zhao, P. Sichta

    2009-05-29

    In order to provide improved and expanded experimental capabilities, the existing Transrex power supplies at PPPL are to be upgraded and modernized. Each of the 39 power supplies consists of two six pulse silicon controlled rectifier sections forming a twelve pulse power supply. The first modification is to split each supply into two independent six pulse supplies by replacing the existing obsolete twelve pulse firing generator with two commercially available six pulse firing generators. The second change replaces the existing control link with a faster system, with greater capacity, which will allow for independent control of all 78 power supply sections. The third change replaces the existing Computer Automated Measurement and Control (CAMAC) based fault detector with an Experimental Physics and Industrial Control System (EPICS) compatible unit, eliminating the obsolete CAMAC modules. Finally the remaining relay logic and interfaces to the "Hardwired Control System" will be replaces with a Programmable Logic Controller (PLC).

  20. High-voltage supplies for corona-electrostatic separators

    SciTech Connect

    Iuga, A.; Neamtu, V.; Suarasan, I.; Morar, R.; Dascalescu, L.

    1995-12-31

    The selection of the high-voltage supply can play an important role in the optimization of electrostatic separation processes. The present work aimed to evaluate the influence of the main high-voltage parameters (waveform, polarity, level) on the efficiency of electroseparation, in the case of insulation-metal granular mixtures. A roll-type laboratory electroseparator was employed for the experimental study and the tests were carried out with granular materials prelevated from the technological flow sheet of a recycling plant for electric wire scraps. The experiments shown the existence of a strong interdependence between the level of the operating voltage and the other electrical parameters. Although the full-wave rectifier allows for lower operating voltages than the half-wave rectifier, its general effectiveness in electroseparation processes is superior. The optimum operating voltage of an electroseparator seems to be slightly lower than the level at which the frequency of the spark discharges tends to exceed 60 min{sup {minus}1}. The oscillograms of the voltage and of the current across the separator proved to be of great use for studying the transition from corona to spark discharges. Good insulation-metal electroseparation can be achieved at either positive or negative polarity of the high-voltage supply, but negative electrode energization is recommended for most industry applications.

  1. Petroleum supply annual 1995: Volume 1

    SciTech Connect

    1996-05-01

    The {ital Petroleum Supply Annual} contains information on supply and disposition of crude oil and petroleum products. It reflects data collected from the petroleum industry during 1995 through monthly surveys, and it is divided into 2 volumes. This volume contains three sections: summary statistics, detailed statistics, and selected refinery statistics, each with final annual data. (The other volume contains final statistics for each month and replaces data previously published in the {ital Petroleum Supply Monthly}).

  2. Intelligence Support to Supply Chain Risk Management

    DTIC Science & Technology

    2012-06-01

    U.S. companies and increased the brittleness of those chains ( Pettit , Fiksel, and Croxton, 2010; Giunipero and Eltantawy, 2004). Attempts to minimize...management. According to Pettit , Fiksel, and Croxton (2010:6), a supply chain is “the network of companies involved in the upstream and downstream...comprise a supply chain and the effects of an uncertain external environment, supply chains are vulnerable to disruption ( Pettit , Fiksel,and Croxton

  3. Finding gold in the supply chain.

    PubMed

    Caudle, Allen

    2009-12-01

    To optimize supply chain performance and achieve savings that enhance the bottom line, hospitals should: Generate purchase orders for every item purchased. Ensure the organization is protected from undue vendor influence. Keep track of where supply chain dollars are going. Review contracts regularly to ensure competitiveness. Have a contract for each product category. Buy only what the organization is sure to use. Get rid of excess inventory. Develop a strategic plan for continued supply chain savings.

  4. Simplified power supplies for ion thrusters

    NASA Technical Reports Server (NTRS)

    Gruber, R. P.

    1981-01-01

    The initial development and demonstration of power supplies with an order of magnitude reduction in parts count, leading to increased reliability at lower weight, while still maintaining thrust system performance are discussed. Two new self-regulating keeper power supply circuits were developed and tested. One supply comprises 14 parts and uses an input voltage range of 18 to 36 volts, the other operates from 200 to 400 volts and requires 22 components. A technique for controlling heater power is also demonstrated.

  5. ARN Supply Chain Management System for OCIE

    DTIC Science & Technology

    2006-12-30

    APPAREL RESEARCH NETWORK (ARN) PROGRAM Final Technical Report Contract Number SP0103-02-D-0018/ Delivery Order 0003 ARN Supply Chain Management...3. REPORT TYPE AND DATES COVERED Technical Report – 27 February 2003 to 30 June 2006 4. TITLE AND SUBTITLE ARN Supply Chain Management System for...Module (IRM), Clothing Initial Issue Point (CIIP); Supply Chain Management; Virtual Item Manager/Wholesale Local; Quality Logistics Management

  6. Shock-activated electrochemical power supplies

    DOEpatents

    Benedick, W.B.; Graham, R.A.; Morosin, B.

    1987-04-20

    A shock-activated electrochemical power supply is provided which is initiated extremely rapidly and which has a long shelf life. Electrochemical power supplies of this invention are initiated much faster than conventional thermal batteries. Power supplies of this invention comprise an inactive electrolyte and means for generating a high-pressure shock wave such that the shock wave is propagated through the electrolyte rendering the electrolyte electrochemically active. 2 figs.

  7. Shock-activated electrochemical power supplies

    DOEpatents

    Benedick, William B.; Graham, Robert A.; Morosin, Bruno

    1988-01-01

    A shock-activated electrochemical power supply is provided which is initiated extremely rapidly and which has a long shelf life. Electrochemical power supplies of this invention are initiated much faster than conventional thermal batteries. Power supplies of this invention comprise an inactive electrolyte and means for generating a high-pressure shock wave such that the shock wave is propagated through the electrolytes rendering the electrolyte electrochemically active.

  8. Shock-activated electrochemical power supplies

    DOEpatents

    Benedick, W.B.; Graham, R.A.; Morosin, B.

    1988-11-08

    A shock-activated electrochemical power supply is provided which is initiated extremely rapidly and which has a long shelf life. Electrochemical power supplies of this invention are initiated much faster than conventional thermal batteries. Power supplies of this invention comprise an inactive electrolyte and means for generating a high-pressure shock wave such that the shock wave is propagated through the electrolytes rendering the electrolyte electrochemically active. 2 figs.

  9. Relativistic mixtures of charged and uncharged particles

    SciTech Connect

    Kremer, Gilberto M.

    2014-01-14

    Mixtures of relativistic gases within the framework of Boltzmann equation are analyzed. Three systems are considered. The first one refers to a mixture of uncharged particles by using Grad’s moment method, where the relativistic mixture is characterized by the moments of the distribution functions: particle four-flows, energy-momentum tensors, and third-order moment tensors. In the second Fick’s law for a mixture of relativistic gases of non-disparate rest masses in a Schwarzschild metric are derived from an extension of Marle and McCormack model equations applied to a relativistic truncated Grad’s distribution function, where it is shown the dependence of the diffusion coefficient on the gravitational potential. The third one consists in the derivation of the relativistic laws of Ohm and Fourier for a binary mixtures of electrons with protons and electrons with photons subjected to external electromagnetic fields and in presence of gravitational fields by using the Anderson and Witting model of the Boltzmann equation.

  10. Mixture models for distance sampling detection functions.

    PubMed

    Miller, David L; Thomas, Len

    2015-01-01

    We present a new class of models for the detection function in distance sampling surveys of wildlife populations, based on finite mixtures of simple parametric key functions such as the half-normal. The models share many of the features of the widely-used "key function plus series adjustment" (K+A) formulation: they are flexible, produce plausible shapes with a small number of parameters, allow incorporation of covariates in addition to distance and can be fitted using maximum likelihood. One important advantage over the K+A approach is that the mixtures are automatically monotonic non-increasing and non-negative, so constrained optimization is not required to ensure distance sampling assumptions are honoured. We compare the mixture formulation to the K+A approach using simulations to evaluate its applicability in a wide set of challenging situations. We also re-analyze four previously problematic real-world case studies. We find mixtures outperform K+A methods in many cases, particularly spiked line transect data (i.e., where detectability drops rapidly at small distances) and larger sample sizes. We recommend that current standard model selection methods for distance sampling detection functions are extended to include mixture models in the candidate set.

  11. A constitutive theory of reacting electrolyte mixtures

    NASA Astrophysics Data System (ADS)

    Costa Reis, Martina; Wang, Yongqi; Bono Maurizio Sacchi Bassi, Adalberto

    2013-11-01

    A constitutive theory of reacting electrolyte mixtures is formulated. The intermolecular interactions among the constituents of the mixture are accounted for through additional freedom degrees to each constituent of the mixture. Balance equations for polar reacting continuum mixtures are accordingly formulated and a proper set of constitutive equations is derived with basis in the Müller-Liu formulation of the second law of thermodynamics. Moreover, the non-equilibrium and equilibrium responses of the reacting mixture are investigated in detail by emphasizing the inner and reactive structures of the medium. From the balance laws and constitutive relations, the effects of molecular structure of constituents upon the fluid flow are studied. It is also demonstrated that the local thermodynamic equilibrium state can be reached without imposing that the set of independent constitutive variables is time independent, neither spatially homogeneous nor null. The resulting constitutive relations presented throughout this work are of relevance to many practical applications, such as swelling of clays, developing of bio and polymeric membranes, and use of electrorheological fluids in industrial processes. The first author acknowledges financial support from National Counsel of Technological and Scientific Development (CNPq) and German Academic Exchange Service (DAAD).

  12. Coal-water mixture fuel burner

    DOEpatents

    Brown, T.D.; Reehl, D.P.; Walbert, G.F.

    1985-04-29

    The present invention represents an improvement over the prior art by providing a rotating cup burner arrangement for use with a coal-water mixture fuel which applies a thin, uniform sheet of fuel onto the inner surface of the rotating cup, inhibits the collection of unburned fuel on the inner surface of the cup, reduces the slurry to a collection of fine particles upon discharge from the rotating cup, and further atomizes the fuel as it enters the combustion chamber by subjecting it to the high shear force of a high velocity air flow. Accordingly, it is an object of the present invention to provide for improved combustion of a coal-water mixture fuel. It is another object of the present invention to provide an arrangement for introducing a coal-water mixture fuel into a combustion chamber in a manner which provides improved flame control and stability, more efficient combustion of the hydrocarbon fuel, and continuous, reliable burner operation. Yet another object of the present invention is to provide for the continuous, sustained combustion of a coal-water mixture fuel without the need for a secondary combustion source such as natural gas or a liquid hydrocarbon fuel. Still another object of the present invention is to provide a burner arrangement capable of accommodating a coal-water mixture fuel having a wide range of rheological and combustion characteristics in providing for its efficient combustion. 7 figs.

  13. Supply chain optimization for pediatric perioperative departments.

    PubMed

    Davis, Janice L; Doyle, Robert

    2011-09-01

    Economic challenges compel pediatric perioperative departments to reduce nonlabor supply costs while maintaining the quality of patient care. Optimization of the supply chain introduces a framework for decision making that drives fiscally responsible decisions. The cost-effective supply chain is driven by implementing a value analysis process for product selection, being mindful of product sourcing decisions to reduce supply expense, creating logistical efficiency that will eliminate redundant processes, and managing inventory to ensure product availability. The value analysis approach is an analytical methodology for product selection that involves product evaluation and recommendation based on consideration of clinical benefit, overall financial impact, and revenue implications.

  14. Automating the supply chain in the OR.

    PubMed

    Graham, J; Brewer, M S; Byrd, V T

    1999-08-01

    At the University of Louisville (Ky) Hospital, staff members from the materials management and surgery departments have worked together to automate the supply chain. The goals were to remove supply activities from clinical staff members whenever possible, obtain and apply information for better product ordering and use, reduce personnel in the materials management department, and improve perioperative nurses' ability to obtain supplies--all at a decreased cost to the facility. This article describes how, after implementing point-of-service technology for all surgical supplies, the facility realized a cost-per-procedure savings of 16% and increased satisfaction among staff members in both departments.

  15. CATALYTIC GASIFICATION OF COAL USING EUTECTIC SALT MIXTURES

    SciTech Connect

    Dr. Yaw D. Yeboah; Dr. Yong Xu; Dr. Atul Sheth; Dr. Pradeep Agrawal

    2001-12-01

    The Gas Research Institute (GRI) estimates that by the year 2010, 40% or more of U.S. gas supply will be provided by supplements including substitute natural gas (SNG) from coal. These supplements must be cost competitive with other energy sources. The first generation technologies for coal gasification e.g. the Lurgi Pressure Gasification Process and the relatively newer technologies e.g. the KBW (Westinghouse) Ash Agglomerating Fluidized-Bed, U-Gas Ash Agglomerating Fluidized-Bed, British Gas Corporation/Lurgi Slagging Gasifier, Texaco Moving-Bed Gasifier, and Dow and Shell Gasification Processes, have several disadvantages. These disadvantages include high severities of gasification conditions, low methane production, high oxygen consumption, inability to handle caking coals, and unattractive economics. Another problem encountered in catalytic coal gasification is deactivation of hydroxide forms of alkali and alkaline earth metal catalysts by oxides of carbon (CO{sub x}). To seek solutions to these problems, a team consisting of Clark Atlanta University (CAU, a Historically Black College and University, HBCU), the University of Tennessee Space Institute (UTSI) and Georgia Institute of Technology (Georgia Tech) proposed to identify suitable low melting eutectic salt mixtures for improved coal gasification. The research objectives of this project were to: Identify appropriate eutectic salt mixture catalysts for coal gasification; Assess agglomeration tendency of catalyzed coal; Evaluate various catalyst impregnation techniques to improve initial catalyst dispersion; Determine catalyst dispersion at high carbon conversion levels; Evaluate effects of major process variables (such as temperature, system pressure, etc.) on coal gasification; Evaluate the recovery, regeneration and recycle of the spent catalysts; and Conduct an analysis and modeling of the gasification process to provide better understanding of the fundamental mechanisms and kinetics of the process.

  16. Advanced Accessory Power Supply Topologies

    SciTech Connect

    Marlino, L.D.

    2010-06-15

    This Cooperative Research and Development Agreement (CRADA) began December 8, 2000 and ended September 30, 2009. The total funding provided by the Participant (General Motors Advanced Technology Vehicles [GM]) during the course of the CRADA totaled $1.2M enabling the Contractor (UT-Battelle, LLC [Oak Ridge National Laboratory, a.k.a. ORNL]) to contribute significantly to the joint project. The initial task was to work with GM on the feasibility of developing their conceptual approach of modifying major components of the existing traction inverter/drive to develop low cost, robust, accessory power. Two alternate methods for implementation were suggested by ORNL and both were proven successful through simulations and then extensive testing of prototypes designed and fabricated during the project. This validated the GM overall concept. Moreover, three joint U.S. patents were issued and subsequently licensed by GM. After successfully fulfilling the initial objective, the direction and duration of the CRADA was modified and GM provided funding for two additional tasks. The first new task was to provide the basic development for implementing a cascaded inverter technology into hybrid vehicles (including plug-in hybrid, fuel cell, and electric). The second new task was to continue the basic development for implementing inverter and converter topologies and new technology assessments for hybrid vehicle applications. Additionally, this task was to address the use of high temperature components in drive systems. Under this CRADA, ORNL conducted further research based on GM’s idea of using the motor magnetic core and windings to produce bidirectional accessory power supply that is nongalvanically coupled to the terminals of the high voltage dc-link battery of hybrid vehicles. In order not to interfere with the motor’s torque, ORNL suggested to use the zero-sequence, highfrequency harmonics carried by the main fundamental motor current for producing the accessory power

  17. Future global crude oil supply

    SciTech Connect

    Ivanhoe, L.F.

    1988-03-01

    Inexpensive crude oil fuels the world's economies and armies. In 1986, for the first time, the global production of crude oil and natural liquids exceeded new reserves added. Proved oil reserves at the end of 1985 stood 707.6 billion bbl (BBO), but declined to 703.1 BBO by the end of 1986. The 1986 reserve decrease, 4.5 BBO, was 20.4% of total global production of 22.0 BBO. This handwriting on the wall is very bad news. The world's recoverable crude oil and natural gas liquids discovered through 1985 totaled 1258 BBO, including cumulative production of 551 BBO and 707 BBO of reserves. At current production rates, half of all discovered oil will have been burned up by 1989. Timing of the end of our oil age can be extrapolated from a modified Hubbert curve, with future production resembling a mirror image of past production. The watershed beginning of the inevitable decline in global crude oil supplies can be expected in the late 1990s, although the date may be over 30 years later in some super-oily Organization of Petroleum Exporting Countries (OPEC). Clearly the day of reckoning will be postponed by any new oil discoveries. These will probably be distributed much as are the present global reserves (e.g., 68% OPEC; 11% USSR and China; 21% rest of world). Of this 56% will be in the Persian Gulf area. Giant fields (more than 0.5 BBO reserves) contain 75% of the world's reserves. Discoveries of oil in the globe's 320 known giant fields peaked at 125 BBO during the period 1961-1965, after which giant field discoveries plunged to only 10 BBO during 1981-1985. Henceforth, they should expect to find few giant whales (but many minnows) in the non-OPEC world's fished-out basins. Every new field will help as global crude oil supplies dwindle. Therefore, it is essential that all large prospects outside the Persian Gulf be tested promptly, so the oil-importing nations will known what size of non-OPEC reserves are available.

  18. Micromorphic Theory of Bubbly Fluid Mixtures

    NASA Astrophysics Data System (ADS)

    Li, Weiming; Paolucci, Samuel

    2008-11-01

    We use a continuum theory for multiphase immiscible mixtures with inner structure. Based on micromorphic theory, the average balance equations for the different phases, as well as for the mixture, result from a systematic averaging procedure. In addition to equations for mass, momentum, energy and entropy, the balance equations also include equations for microinertia and microspin tensors. These equations, together with appropriate constitutive equations consistent with the entropy inequality, enable the modeling of immiscible multiphase materials where internal parameters are important. Here, we apply the results to a two-phase simple microstretch (expansion or contraction) bubbly fluid mixture. We show that the equations for microspin and microinertia, under a number of simplifying assumptions, combine to yield a general form of the Rayleigh-Plesset equation.

  19. Capillary condensation and adsorption of binary mixtures.

    PubMed

    Weinberger, B; Darkrim-Lamari, F; Levesque, D

    2006-06-21

    The adsorption of equimolar binary mixtures of hydrogen-carbon dioxide, hydrogen-methane, and methane-carbon dioxide in porous material models is determined by grand canonical Monte Carlo simulations. The material models have an adsorbent surface similar to that of nanofibers with a herringbone structure. Our main result, which is relevant for hydrogen purification and carbon dioxide capture, is that the adsorption selectivities calculated for the mixtures can differ significantly from those deduced from simulations of the adsorption of pure gases, in particular, when one of the adsorbed gases presents a capillary condensation induced by confinement within the pore network. A comparison of our data is also made with theoretical models used in the literature for predicting the properties of the mixture adsorption.

  20. Mixtures of planetary ices at extreme conditions.

    PubMed

    Lee, Mal-Soon; Scandolo, Sandro

    2011-02-08

    The interiors of Neptune and Uranus are believed to be primarily composed of a fluid mixture of methane and water. The mixture is subjected to pressures up to several hundred gigapascal, causing the ionization of water. Laboratory and simulation studies so far have focused on the properties of the individual components. Here we show, using first-principle molecular dynamic simulations, that the properties of the mixed fluid are qualitatively different with respect to those of its components at the same conditions. We observe a pressure-induced softening of the methane-water intermolecular repulsion that points to an enhancement of mixing under extreme conditions. Ionized water causes the progressive ionization of methane and the mixture becomes electronically conductive at milder conditions than pure water, indicating that the planetary magnetic field of Uranus and Neptune may originate at shallower depths than currently assumed.

  1. Detailed Kinetic Modeling of Gasoline Surrogate Mixtures

    SciTech Connect

    Mehl, M; Curran, H J; Pitz, W J; Westbrook, C K

    2009-03-09

    Real fuels are complex mixtures of thousands of hydrocarbon compounds including linear and branched paraffins, naphthenes, olefins and aromatics. It is generally agreed that their behavior can be effectively reproduced by simpler fuel surrogates containing a limited number of components. In this work, a recently revised version of the kinetic model by the authors is used to analyze the combustion behavior of several components relevant to gasoline surrogate formulation. Particular attention is devoted to linear and branched saturated hydrocarbons (PRF mixtures), olefins (1-hexene) and aromatics (toluene). Model predictions for pure components, binary mixtures and multi-component gasoline surrogates are compared with recent experimental information collected in rapid compression machine, shock tube and jet stirred reactors covering a wide range of conditions pertinent to internal combustion engines. Simulation results are discussed focusing attention on the mixing effects of the fuel components.

  2. Biomass Supply Logistics and Infrastructure

    SciTech Connect

    Sokhansanj, Shahabaddine

    2009-04-01

    Feedstock supply system encompasses numerous unit operations necessary to move lignocellulosic feedstock from the place where it is produced (in the field or on the stump) to the start of the conversion process (reactor throat) of the Biorefinery. These unit operations, which include collection, storage, preprocessing, handling, and transportation, represent one of the largest technical and logistics challenges to the emerging lignocellulosic biorefining industry. This chapter briefly reviews methods of estimating the quantities of biomass followed by harvesting and collection processes based on current practices on handling wet and dry forage materials. Storage and queuing are used to deal with seasonal harvest times, variable yields, and delivery schedules. Preprocessing can be as simple as grinding and formatting the biomass for increased bulk density or improved conversion efficiency, or it can be as complex as improving feedstock quality through fractionation, tissue separation, drying, blending, and densification. Handling and Transportation consists of using a variety of transport equipment (truck, train, ship) for moving the biomass from one point to another. The chapter also provides typical cost figures for harvest and processing of biomass.

  3. Biomass supply logistics and infrastructure.

    PubMed

    Sokhansanj, Shahabaddine; Hess, J Richard

    2009-01-01

    Feedstock supply system encompasses numerous unit operations necessary to move lignocellulosic feedstock from the place where it is produced (in the field or on the stump) to the start of the conversion process (reactor throat) of the biorefinery. These unit operations, which include collection, storage, preprocessing, handling, and transportation, represent one of the largest technical and logistics challenges to the emerging lignocellulosic biorefining industry. This chapter briefly reviews the methods of estimating the quantities of biomass, followed by harvesting and collection processes based on current practices on handling wet and dry forage materials. Storage and queuing are used to deal with seasonal harvest times, variable yields, and delivery schedules. Preprocessing can be as simple as grinding and formatting the biomass for increased bulk density or improved conversion efficiency, or it can be as complex as improving feedstock quality through fractionation, tissue separation, drying, blending, and densification. Handling and transportation consists of using a variety of transport equipment (truck, train, ship) for moving the biomass from one point to another. The chapter also provides typical cost figures for harvest and processing of biomass.

  4. Protective supplied breathing air garment

    DOEpatents

    Childers, E.L.; Hortenau, E.F. von.

    1984-07-10

    A breathing air garment is disclosed for isolating a wearer from hostile environments containing toxins or irritants includes a suit and a separate head protective enclosure or hood engaging a suit collar in sealing attachment. The hood and suit collar are cylindrically shaped and dimensioned to enable the wearer to withdraw his hands from the suit sleeves to perform manual tasks within the hood interior. Breathing air is supplied from an external air line with an air delivery hose attached to the hood interior. The hose feeds air into an annular halo-like fiber-filled plenum having spaced discharge orifices attached to the hood top wall. A plurality of air exhaust/check valves located at the suit extremities cooperate with the hood air delivery system to provide a cooling flow of circulating air from the hood throughout the suit interior. A suit entry seal provided on the suit rear torso panel permits access into the suit and is sealed with an adhesive sealing flap. 17 figs.

  5. Protective supplied breathing air garment

    DOEpatents

    Childers, Edward L.; von Hortenau, Erik F.

    1984-07-10

    A breathing air garment for isolating a wearer from hostile environments containing toxins or irritants includes a suit and a separate head protective enclosure or hood engaging a suit collar in sealing attachment. The hood and suit collar are cylindrically shaped and dimensioned to enable the wearer to withdraw his hands from the suit sleeves to perform manual tasks within the hood interior. Breathing air is supplied from an external air line with an air delivery hose attached to the hood interior. The hose feeds air into an annular halo-like fiber-filled plenum having spaced discharge orifices attached to the hood top wall. A plurality of air exhaust/check valves located at the suit extremities cooperate with the hood air delivery system to provide a cooling flow of circulating air from the hood throughout the suit interior. A suit entry seal provided on the suit rear torso panel permits access into the suit and is sealed with an adhesive sealing flap.

  6. Water supply and management concepts

    USGS Publications Warehouse

    Leopold, Luna Bergere

    1965-01-01

    If I had to cite one fact about water in the United States which would be not only the most important but also the most informative, the one I would choose would k this: Over 50 percent of all the water presently being used in the United States is used by industry, and nearly all of that is used for cooling.The large amount of attention recently being given to water shortage and the expected rapid increase in demand for water is probably to some extent clouded because there are certain simple facts about water availability and water use which, though readily available, are not generally either known or understood.Probably most people react to information in the public press about present and possible future water shortages with the thought that it is going to be more difficult in the future to supply the ordinary household with water for drinking, washing, and tbe culinary arts. As a matter of fact that may be true to some extent, but it is not the salient aspect.

  7. Near azeotropic mixture substitute for dichlorodifluoromethane

    NASA Technical Reports Server (NTRS)

    Jones, Jack A. (Inventor)

    1996-01-01

    The present invention comprises a refrigerant mixture having two halocarbon components. The first component is present in a mole fraction of about 0.7 to less than 1.0 while the second component is present in a mole fraction of more than 0.0 to about 0.3. The first component is CH.sub.2 FCF.sub.3. The second component can be CHClFCF.sub.3, CH.sub.3 CClF.sub.2, a mixture of CHClFCF.sub.3 and CH.sub.3 CClF.sub.2, a mixture of CHF.sub.2 CH.sub.3 and CHClFCF.sub.3, a mixture of CHF.sub.2 CH.sub.3 and CH.sub.3 CClF.sub.2, or a mixture of CHClFCF.sub.3, CH.sub.3 CClF.sub.2 and CHF.sub.2 CH.sub.3. The preferred embodiment of this invention comprises about 0.7 to less than 1.0 mole fraction CH.sub.2 FCF.sub.3, and more than 0.0 to about 0.3 mole fraction of a mixture of CHClFCF.sub.3 and CH.sub.3 CClF.sub.2. The most preferred embodiment of this invention comprises about 0.7 to less than 1.0 mole fraction CH.sub.2 FCF.sub.3 and more than 0.0 to about 0.3 mole fraction CH.sub.3 CClF.sub.2. The resulting refrigerant has a vapor pressure close to-that of CF.sub.2 Cl.sub.2, a nearly constant vapor pressure with evaporation, and is substantially less damaging to the Earth's ozone layer than CF.sub.2 Cl.sub.2.

  8. Mutation spectra of complex environmental mixtures

    SciTech Connect

    DeMarini, D.M.

    1997-10-01

    Bioassay-directed chemical analysis of complex environmental mixtures has indicated that much of the genotoxic activity of mixtures is due to the presence of one or a few classes or chemicals within the mixture. We have extended this observation to the molecular level by using colony probe hybridization and PCR/DNA sequence analysis to determine the mutation spectra of {approximately}8,000 revertants induced by a variety of complex mixtures and their chemical fractions in TA100 and TA98 of Salmonella. For urban air, >80% of mutagenic activity was due to a base/neutral fraction that contained primarily PAHs. The mutation spectrum induced by unfractionated urban air was not significantly different from that produced by a model PAH, B(a)P. The mutation spectrum induced by organic extracts of chlorinated drinking water were similar to those produced by the chlorinated furanone MX, which accounted for {approximately}20% of the mutagenic activity of the samples. The base/neutral fraction of municipal waste incinerator emissions accounted for the primary class of mutations induced by the emissions, and a polar neutral fraction accounted for the secondary class of mutations induced by the emissions. The primary class of mutations induced by cigarette smoke condensate in TA100 (GC {yields} TA) is also the primary class of mutations in the p53 gene of lung tumors of cigarette smokers. These results confirm at the molecular level that the mutations induced by a complex mixture reflect the dominance of one or a few classes of chemicals within the mixture.

  9. Electrical signatures of ethanol-liquid mixtures: implications for monitoring biofuels migration in the subsurface

    USGS Publications Warehouse

    Personna, Yves Robert; Slater, Lee; Ntarlagiannis, Dimitrios; Werkema, Dale; Szabo, Zoltan

    2013-01-01

    Ethanol (EtOH), an emerging contaminant with potential direct and indirect environmental effects, poses threats to water supplies when spilled in large volumes. A series of experiments was directed at understanding the electrical geophysical signatures arising from groundwater contamination by ethanol. Conductivity measurements were performed at the laboratory scale on EtOH–water mixtures (0 to 0.97 v/v EtOH) and EtOH–salt solution mixtures (0 to 0.99 v/v EtOH) with and without a sand matrix using a conductivity probe and a four-electrode electrical measurement over the low frequency range (1–1000 Hz). A Lichtenecker–Rother (L–R) type mixing model was used to simulate electrical conductivity as a function of EtOH concentration in the mixture. For all three experimental treatments increasing EtOH concentration resulted in a decrease in measured conductivity magnitude (|σ|). The applied L–R model fitted the experimental data at concentration ≤ 0.4 v/v EtOH, presumably due to predominant and symmetric intermolecular (EtOH–water) interaction in the mixture. The deviation of the experimental |σ| data from the model prediction at higher EtOH concentrations may be associated with hydrophobic effects of EtOH–EtOH interactions in the mixture. The |σ| data presumably reflected changes in relative strength of the three types of interactions (water–water, EtOH–water, and EtOH–EtOH) occurring simultaneously in EtOH–water mixtures as the ratio of EtOH to water changed. No evidence of measurable polarization effects at the EtOH–water and EtOH–water–mineral interfaces over the investigated frequency range was found. Our results indicate the potential for using electrical measurements to characterize and monitor EtOH spills in the subsurface.

  10. Electrical signatures of ethanol-liquid mixtures: implications for monitoring biofuels migration in the subsurface.

    PubMed

    Personna, Yves Robert; Slater, Lee; Ntarlagiannis, Dimitrios; Werkema, Dale; Szabo, Zoltan

    2013-01-01

    Ethanol (EtOH), an emerging contaminant with potential direct and indirect environmental effects, poses threats to water supplies when spilled in large volumes. A series of experiments was directed at understanding the electrical geophysical signatures arising from groundwater contamination by ethanol. Conductivity measurements were performed at the laboratory scale on EtOH-water mixtures (0 to 0.97 v/v EtOH) and EtOH-salt solution mixtures (0 to 0.99 v/v EtOH) with and without a sand matrix using a conductivity probe and a four-electrode electrical measurement over the low frequency range (1-1000 Hz). A Lichtenecker-Rother (L-R) type mixing model was used to simulate electrical conductivity as a function of EtOH concentration in the mixture. For all three experimental treatments increasing EtOH concentration resulted in a decrease in measured conductivity magnitude (|σ|). The applied L-R model fitted the experimental data at concentration ≤0.4v/v EtOH, presumably due to predominant and symmetric intermolecular (EtOH-water) interaction in the mixture. The deviation of the experimental |σ| data from the model prediction at higher EtOH concentrations may be associated with hydrophobic effects of EtOH-EtOH interactions in the mixture. The |σ| data presumably reflected changes in relative strength of the three types of interactions (water-water, EtOH-water, and EtOH-EtOH) occurring simultaneously in EtOH-water mixtures as the ratio of EtOH to water changed. No evidence of measurable polarization effects at the EtOH-water and EtOH-water-mineral interfaces over the investigated frequency range was found. Our results indicate the potential for using electrical measurements to characterize and monitor EtOH spills in the subsurface.

  11. Electrical signatures of ethanol-liquid mixtures: Implications for monitoring biofuels migration in the subsurface

    NASA Astrophysics Data System (ADS)

    Personna, Yves Robert; Slater, Lee; Ntarlagiannis, Dimitrios; Werkema, Dale; Szabo, Zoltan

    2013-01-01

    Ethanol (EtOH), an emerging contaminant with potential direct and indirect environmental effects, poses threats to water supplies when spilled in large volumes. A series of experiments was directed at understanding the electrical geophysical signatures arising from groundwater contamination by ethanol. Conductivity measurements were performed at the laboratory scale on EtOH-water mixtures (0 to 0.97 v/v EtOH) and EtOH-salt solution mixtures (0 to 0.99 v/v EtOH) with and without a sand matrix using a conductivity probe and a four-electrode electrical measurement over the low frequency range (1-1000 Hz). A Lichtenecker-Rother (L-R) type mixing model was used to simulate electrical conductivity as a function of EtOH concentration in the mixture. For all three experimental treatments increasing EtOH concentration resulted in a decrease in measured conductivity magnitude (|σ|). The applied L-R model fitted the experimental data at concentration ≤ 0.4 v/v EtOH, presumably due to predominant and symmetric intermolecular (EtOH-water) interaction in the mixture. The deviation of the experimental |σ| data from the model prediction at higher EtOH concentrations may be associated with hydrophobic effects of EtOH-EtOH interactions in the mixture. The |σ| data presumably reflected changes in relative strength of the three types of interactions (water-water, EtOH-water, and EtOH-EtOH) occurring simultaneously in EtOH-water mixtures as the ratio of EtOH to water changed. No evidence of measurable polarization effects at the EtOH-water and EtOH-water-mineral interfaces over the investigated frequency range was found. Our results indicate the potential for using electrical measurements to characterize and monitor EtOH spills in the subsurface.

  12. Thermophysical Properties of Fluids and Fluid Mixtures

    SciTech Connect

    Sengers, Jan V.; Anisimov, Mikhail A.

    2004-05-03

    The major goal of the project was to study the effect of critical fluctuations on the thermophysical properties and phase behavior of fluids and fluid mixtures. Long-range fluctuations appear because of the presence of critical phase transitions. A global theory of critical fluctuations was developed and applied to represent thermodynamic properties and transport properties of molecular fluids and fluid mixtures. In the second phase of the project, the theory was extended to deal with critical fluctuations in complex fluids such as polymer solutions and electrolyte solutions. The theoretical predictions have been confirmed by computer simulations and by light-scattering experiments. Fluctuations in fluids in nonequilibrium states have also been investigated.

  13. 21 CFR 1310.12 - Exempt chemical mixtures.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... aqueous or alcoholic solutions, is not considered a mixture. Weight is based on sulfuric acid in the... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Exempt chemical mixtures. 1310.12 Section 1310.12... CHEMICALS AND CERTAIN MACHINES § 1310.12 Exempt chemical mixtures. (a) The chemical mixtures meeting...

  14. Productivity, botanical composition, and nutritive value of commercial pasture mixtures

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Pastures in the northeastern USA often are planted to mixtures of grasses and legumes. There is limited public sector information on the performance of commercial forage mixtures. We evaluated a range of commercial pasture mixtures to determine if the number of species in a mixture affected yield an...

  15. Effects of enterprise technology on supply chain collaboration: analysis of China-linked supply chain

    NASA Astrophysics Data System (ADS)

    Li, Ling

    2012-02-01

    Supply chain collaboration has received increasing attention from scholars and practitioners in recent years. However, our understanding of how enterprise information technology facilitates supply chain collaboration is still very limited, especially with regard to Chinese enterprise ownerships such as state-owned firms, joint-venture firms and local village-owned firms. This paper extends the theory established in enterprise information technology (IT) and supply chain collaboration literature and relates it with coordination in China-linked supply chain. Drawing upon an empirical study from 177 Chinese companies, we provide three major findings: (i) uncovered the importance of leveraging enterprise IT through supply chain collaboration; (ii) identified the relationship between enterprise ownership and enterprise technology use and supply chain collaboration in China-linked supply chain and (iii) illustrated effects of supply chain collaborative activities on operational and market performance.

  16. The Effects of Supply Chain Orientation, Supply Chain Management, and Collaboration on Perceived Firm Performance

    DTIC Science & Technology

    2012-06-01

    for firms to be managed as a complete system ; therefore an initial phase in SCM involves creating a vision for all members of the supply chain and...between supply chain orientation (SCO), supply chain management ( SCM ), collaboration, and the effects of those concepts on firm performance are of...previous research however there is a distinction between SCO and SCM . SCO is the manifestation of the supply chain mindset within the firm, while SCM

  17. School Nurse Inspections Improve Handwashing Supplies

    ERIC Educational Resources Information Center

    Ramos, Mary M.; Schrader, Ronald; Trujillo, Rebecca; Blea, Mary; Greenberg, Cynthia

    2011-01-01

    Background: Handwashing in the school setting is important for infectious disease control, yet maintaining adequate handwashing supplies is often made difficult by lack of funds, limited staff time, and student vandalism. This study measured the availability of handwashing supplies for students in New Mexico public schools and determined the…

  18. 7 CFR 1126.6 - Supply plant.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 9 2011-01-01 2011-01-01 false Supply plant. 1126.6 Section 1126.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1126.6 Supply plant. See § 1000.6....

  19. 7 CFR 1001.6 - Supply plant.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 9 2011-01-01 2011-01-01 false Supply plant. 1001.6 Section 1001.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1001.6 Supply plant. See § 1000.6....

  20. 7 CFR 1124.6 - Supply plant.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 9 2011-01-01 2011-01-01 false Supply plant. 1124.6 Section 1124.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Definitions § 1124.6 Supply plant. See § 1000.6....

  1. 7 CFR 1131.6 - Supply plant.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 9 2010-01-01 2009-01-01 true Supply plant. 1131.6 Section 1131.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1131.6 Supply plant. See § 1000.6....

  2. 7 CFR 1131.6 - Supply plant.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 9 2011-01-01 2011-01-01 false Supply plant. 1131.6 Section 1131.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1131.6 Supply plant. See § 1000.6....

  3. 7 CFR 1032.6 - Supply plant.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 9 2010-01-01 2009-01-01 true Supply plant. 1032.6 Section 1032.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1032.6 Supply plant. See § 1000.6....

  4. 7 CFR 1007.6 - Supply plant.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 9 2010-01-01 2009-01-01 true Supply plant. 1007.6 Section 1007.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1007.6 Supply plant. See § 1000.6....

  5. 7 CFR 1006.6 - Supply plant.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 9 2010-01-01 2009-01-01 true Supply plant. 1006.6 Section 1006.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1006.6 Supply plant. See § 1000.6....

  6. 7 CFR 1005.6 - Supply plant.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 9 2010-01-01 2009-01-01 true Supply plant. 1005.6 Section 1005.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1005.6 Supply plant. See § 1000.6....

  7. 7 CFR 1007.6 - Supply plant.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 9 2011-01-01 2011-01-01 false Supply plant. 1007.6 Section 1007.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1007.6 Supply plant. See § 1000.6....

  8. 7 CFR 1032.6 - Supply plant.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 9 2011-01-01 2011-01-01 false Supply plant. 1032.6 Section 1032.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1032.6 Supply plant. See § 1000.6....

  9. 7 CFR 1001.6 - Supply plant.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 9 2010-01-01 2009-01-01 true Supply plant. 1001.6 Section 1001.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1001.6 Supply plant. See § 1000.6....

  10. 7 CFR 1126.6 - Supply plant.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 9 2010-01-01 2009-01-01 true Supply plant. 1126.6 Section 1126.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1126.6 Supply plant. See § 1000.6....

  11. 7 CFR 1006.6 - Supply plant.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 9 2011-01-01 2011-01-01 false Supply plant. 1006.6 Section 1006.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1006.6 Supply plant. See § 1000.6....

  12. 7 CFR 1030.6 - Supply plant.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 9 2010-01-01 2009-01-01 true Supply plant. 1030.6 Section 1030.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1030.6 Supply plant. See § 1000.6....

  13. 7 CFR 1033.6 - Supply plant.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 9 2010-01-01 2009-01-01 true Supply plant. 1033.6 Section 1033.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1033.6 Supply plant. See § 1000.6....

  14. 7 CFR 1005.6 - Supply plant.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 9 2011-01-01 2011-01-01 false Supply plant. 1005.6 Section 1005.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1005.6 Supply plant. See § 1000.6....

  15. 7 CFR 1124.6 - Supply plant.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 9 2010-01-01 2009-01-01 true Supply plant. 1124.6 Section 1124.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Definitions § 1124.6 Supply plant. See § 1000.6....

  16. 7 CFR 1033.6 - Supply plant.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 9 2011-01-01 2011-01-01 false Supply plant. 1033.6 Section 1033.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1033.6 Supply plant. See § 1000.6....

  17. 7 CFR 1030.6 - Supply plant.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 9 2011-01-01 2011-01-01 false Supply plant. 1030.6 Section 1030.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1030.6 Supply plant. See § 1000.6....

  18. 46 CFR 169.688 - Power supply.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Power supply. 169.688 Section 169.688 Shipping COAST... Electrical Electrical Installations on Vessels of 100 Gross Tons and Over § 169.688 Power supply. (a) The... provide electric power for any vital system listed in § 169.642 of this subchapter, at least...

  19. 49 CFR 236.516 - Power supply.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Power supply. 236.516 Section 236.516..., Train Control and Cab Signal Systems Standards § 236.516 Power supply. Automatic cab signal, train stop, or train control device hereafter installed shall operate from a separate or isolated power...

  20. 43 CFR 12.73 - Supplies.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 43 Public Lands: Interior 1 2010-10-01 2010-10-01 false Supplies. 12.73 Section 12.73 Public Lands: Interior Office of the Secretary of the Interior ADMINISTRATIVE AND AUDIT REQUIREMENTS AND COST PRINCIPLES... State and Local Governments Changes, Property, and Subawards § 12.73 Supplies. (a) Title. Title...

  1. 76 FR 67721 - PNE Energy Supply, LLC;

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-11-02

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF ENERGY Federal Energy Regulatory Commission PNE Energy Supply, LLC; Supplemental Notice that Initial Market-Based Rate...-referenced proceeding of PNE Energy Supply, LLC's application for market-based rate authority, with...

  2. Present and Future Supply of Registered Nurses.

    ERIC Educational Resources Information Center

    Altman, Stuart H.

    During the 1960's, nursing education shifted dramatically away from hospital-operated diploma schools toward associate degree and baccalaureate programs. This report examines the nature of this shift in training and its anticipated impact on future supply. Other important factors affecting the future supply of nurses are analyzed, including the…

  3. 46 CFR 169.688 - Power supply.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 46 Shipping 7 2013-10-01 2013-10-01 false Power supply. 169.688 Section 169.688 Shipping COAST... Electrical Electrical Installations on Vessels of 100 Gross Tons and Over § 169.688 Power supply. (a) The... provide electric power for any vital system listed in § 169.642 of this subchapter, at least...

  4. 46 CFR 169.688 - Power supply.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 46 Shipping 7 2012-10-01 2012-10-01 false Power supply. 169.688 Section 169.688 Shipping COAST... Electrical Electrical Installations on Vessels of 100 Gross Tons and Over § 169.688 Power supply. (a) The... provide electric power for any vital system listed in § 169.642 of this subchapter, at least...

  5. Improved Programmable High-Voltage Power Supply

    NASA Technical Reports Server (NTRS)

    Castell, Karen; Rutberg, Arthur

    1994-01-01

    Improved dc-to-dc converter functions as programmable high-voltage power supply with low-power-dissipation voltage regulator on high-voltage side. Design of power supply overcomes deficiencies of older designs. Voltage regulation with low power dissipation provided on high-voltage side.

  6. 48 CFR 11.701 - Supply contracts.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... DESCRIBING AGENCY NEEDS Variation in Quantity 11.701 Supply contracts. (a) A fixed-price supply contract may authorize Government acceptance of a variation in the quantity of items called for if the variation is... permissible variation shall be stated as a percentage and it may be an increase, a decrease, or a...

  7. 38 CFR 21.210 - Supplies.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) Extended evaluation; (2) Rehabilitation to the point of employability; (3) Employment services; and (4) An... REHABILITATION AND EDUCATION Vocational Rehabilitation and Employment Under 38 U.S.C. Chapter 31 Supplies § 21... rehabilitation and achieve the goals of his or her program. (b) Definition. The term supplies includes...

  8. Supply Chain Sourcing Game: A Negotiation Exercise

    ERIC Educational Resources Information Center

    Gumus, Mehmet; Love, Ernie C.

    2013-01-01

    This article introduces an exercise that simulates the negotiation process in a dynamic supply chain. The retailer and wholesaler roles are assigned to student groups who negotiate supply contracts in a number of rounds during a class period. Each group makes pricing, inventory, and ordering decision concurrently, and competes with others to…

  9. 21 CFR 1403.33 - Supplies.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 9 2011-04-01 2011-04-01 false Supplies. 1403.33 Section 1403.33 Food and Drugs OFFICE OF NATIONAL DRUG CONTROL POLICY UNIFORM ADMINISTRATIVE REQUIREMENTS FOR GRANTS AND COOPERATIVE... supplies exceeding $5,000 in total aggregate fair market value upon termination or completion of the...

  10. 21 CFR 1403.33 - Supplies.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 9 2013-04-01 2013-04-01 false Supplies. 1403.33 Section 1403.33 Food and Drugs OFFICE OF NATIONAL DRUG CONTROL POLICY UNIFORM ADMINISTRATIVE REQUIREMENTS FOR GRANTS AND COOPERATIVE... supplies exceeding $5,000 in total aggregate fair market value upon termination or completion of the...

  11. 21 CFR 1403.33 - Supplies.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 9 2012-04-01 2012-04-01 false Supplies. 1403.33 Section 1403.33 Food and Drugs OFFICE OF NATIONAL DRUG CONTROL POLICY UNIFORM ADMINISTRATIVE REQUIREMENTS FOR GRANTS AND COOPERATIVE... supplies exceeding $5,000 in total aggregate fair market value upon termination or completion of the...

  12. 21 CFR 1403.33 - Supplies.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Supplies. 1403.33 Section 1403.33 Food and Drugs OFFICE OF NATIONAL DRUG CONTROL POLICY UNIFORM ADMINISTRATIVE REQUIREMENTS FOR GRANTS AND COOPERATIVE... supplies exceeding $5,000 in total aggregate fair market value upon termination or completion of the...

  13. 45 CFR 602.33 - Supplies.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 45 Public Welfare 3 2010-10-01 2010-10-01 false Supplies. 602.33 Section 602.33 Public Welfare Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE FOUNDATION UNIFORM ADMINISTRATIVE... unused supplies exceeding $5,000 in total aggregate fair market value upon termination or completion...

  14. 45 CFR 602.33 - Supplies.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 45 Public Welfare 3 2011-10-01 2011-10-01 false Supplies. 602.33 Section 602.33 Public Welfare Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE FOUNDATION UNIFORM ADMINISTRATIVE... unused supplies exceeding $5,000 in total aggregate fair market value upon termination or completion...

  15. The Supply of Public School Quality.

    ERIC Educational Resources Information Center

    Brasington, D. M.

    2003-01-01

    Derives price of unit of public-school quality from series of housing-market hedonic estimates, in which house price is regressed as a function of school quality. Inserts implicit price in an estimation of public-school supply. The 0.14 supply elasticity suggests that change in demand will not spur homeowners to increase the quantity of quality…

  16. Commercium Interruptus: Supply Chain Responses to Disaster

    DTIC Science & Technology

    2003-01-01

    lean manufacturing coupled with the improvements in information management eventually resulted in the processes of supply chain management. With regard to supplies, once a company knew where their, inbound materials were because of the linkages of computer systems, had a guaranteed date of delivery from an information-enabled distribution

  17. 44 CFR 13.33 - Supplies.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 44 Emergency Management and Assistance 1 2010-10-01 2010-10-01 false Supplies. 13.33 Section 13.33 Emergency Management and Assistance FEDERAL EMERGENCY MANAGEMENT AGENCY, DEPARTMENT OF HOMELAND SECURITY... GOVERNMENTS Post-Award Requirements Changes, Property, and Subawards § 13.33 Supplies. (a) Title. Title...

  18. 41 CFR 105-71.133 - Supplies.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 41 Public Contracts and Property Management 3 2011-01-01 2011-01-01 false Supplies. 105-71.133 Section 105-71.133 Public Contracts and Property Management Federal Property Management Regulations System...-Award Requirements/Changes, Property, and Subawards § 105-71.133 Supplies. (a) Title. Title to...

  19. 44 CFR 13.33 - Supplies.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 44 Emergency Management and Assistance 1 2011-10-01 2011-10-01 false Supplies. 13.33 Section 13.33 Emergency Management and Assistance FEDERAL EMERGENCY MANAGEMENT AGENCY, DEPARTMENT OF HOMELAND SECURITY... GOVERNMENTS Post-Award Requirements Changes, Property, and Subawards § 13.33 Supplies. (a) Title. Title...

  20. 45 CFR 602.33 - Supplies.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE FOUNDATION UNIFORM ADMINISTRATIVE... unused supplies exceeding $5,000 in total aggregate fair market value upon termination or completion of the award, and if the supplies are not needed for any other federally sponsored programs or...

  1. 45 CFR 602.33 - Supplies.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE FOUNDATION UNIFORM ADMINISTRATIVE... unused supplies exceeding $5,000 in total aggregate fair market value upon termination or completion of the award, and if the supplies are not needed for any other federally sponsored programs or...

  2. 45 CFR 602.33 - Supplies.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... Regulations Relating to Public Welfare (Continued) NATIONAL SCIENCE FOUNDATION UNIFORM ADMINISTRATIVE... unused supplies exceeding $5,000 in total aggregate fair market value upon termination or completion of the award, and if the supplies are not needed for any other federally sponsored programs or...

  3. Naval Logistics Integration Through Interoperable Supply Systems

    DTIC Science & Technology

    2014-06-13

    NAVAL LOGISTICS INTEGRATION THROUGH INTEROPERABLE SUPPLY SYSTEMS A thesis presented to the Faculty of the U.S. Army Command...Thesis 3. DATES COVERED (From - To) AUG 2013 – JUNE 2014 4. TITLE AND SUBTITLE Naval Logistics Integration through Interoperable Supply Systems...Unlimited 13. SUPPLEMENTARY NOTES 14. ABSTRACT This research investigates how the Navy and the Marine Corps could increase Naval Logistics

  4. Finance and supply management project execution plan

    SciTech Connect

    BENNION, S.I.

    1999-02-10

    As a subproject of the HANDI 2000 project, the Finance and Supply Management system is intended to serve FDH and Project Hanford major subcontractor with financial processes including general ledger, project costing, budgeting, and accounts payable, and supply management process including purchasing, inventory and contracts management. Currently these functions are performed with numerous legacy information systems and suboptimized processes.

  5. 7 CFR 1126.6 - Supply plant.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 9 2014-01-01 2013-01-01 true Supply plant. 1126.6 Section 1126.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1126.6 Supply plant. See § 1000.6....

  6. 7 CFR 1030.6 - Supply plant.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 9 2013-01-01 2013-01-01 false Supply plant. 1030.6 Section 1030.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1030.6 Supply plant. See § 1000.6....

  7. 7 CFR 1124.6 - Supply plant.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 9 2014-01-01 2013-01-01 true Supply plant. 1124.6 Section 1124.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Regulating Handling Definitions § 1124.6 Supply plant. See § 1000.6....

  8. 7 CFR 1033.6 - Supply plant.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 9 2014-01-01 2013-01-01 true Supply plant. 1033.6 Section 1033.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1033.6 Supply plant. See § 1000.6....

  9. 7 CFR 1007.6 - Supply plant.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 9 2014-01-01 2013-01-01 true Supply plant. 1007.6 Section 1007.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1007.6 Supply plant. See § 1000.6....

  10. 7 CFR 1030.6 - Supply plant.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 9 2012-01-01 2012-01-01 false Supply plant. 1030.6 Section 1030.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1030.6 Supply plant. See § 1000.6....

  11. 7 CFR 1030.6 - Supply plant.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 9 2014-01-01 2013-01-01 true Supply plant. 1030.6 Section 1030.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1030.6 Supply plant. See § 1000.6....

  12. 7 CFR 1033.6 - Supply plant.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 9 2013-01-01 2013-01-01 false Supply plant. 1033.6 Section 1033.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1033.6 Supply plant. See § 1000.6....

  13. 7 CFR 1005.6 - Supply plant.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 9 2014-01-01 2013-01-01 true Supply plant. 1005.6 Section 1005.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1005.6 Supply plant. See § 1000.6....

  14. 7 CFR 1124.6 - Supply plant.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 9 2013-01-01 2013-01-01 false Supply plant. 1124.6 Section 1124.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Regulating Handling Definitions § 1124.6 Supply plant. See § 1000.6....

  15. 7 CFR 1006.6 - Supply plant.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 9 2012-01-01 2012-01-01 false Supply plant. 1006.6 Section 1006.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1006.6 Supply plant. See § 1000.6....

  16. 7 CFR 1001.6 - Supply plant.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 9 2013-01-01 2013-01-01 false Supply plant. 1001.6 Section 1001.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1001.6 Supply plant. See § 1000.6....

  17. 7 CFR 1006.6 - Supply plant.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 9 2014-01-01 2013-01-01 true Supply plant. 1006.6 Section 1006.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1006.6 Supply plant. See § 1000.6....

  18. 7 CFR 1007.6 - Supply plant.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 9 2012-01-01 2012-01-01 false Supply plant. 1007.6 Section 1007.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1007.6 Supply plant. See § 1000.6....

  19. 7 CFR 1032.6 - Supply plant.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 9 2012-01-01 2012-01-01 false Supply plant. 1032.6 Section 1032.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1032.6 Supply plant. See § 1000.6....

  20. 7 CFR 1126.6 - Supply plant.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 9 2013-01-01 2013-01-01 false Supply plant. 1126.6 Section 1126.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1126.6 Supply plant. See § 1000.6....

  1. 7 CFR 1032.6 - Supply plant.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 9 2014-01-01 2013-01-01 true Supply plant. 1032.6 Section 1032.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1032.6 Supply plant. See § 1000.6....

  2. 7 CFR 1131.6 - Supply plant.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 9 2013-01-01 2013-01-01 false Supply plant. 1131.6 Section 1131.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1131.6 Supply plant. See § 1000.6....

  3. 7 CFR 1005.6 - Supply plant.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 9 2012-01-01 2012-01-01 false Supply plant. 1005.6 Section 1005.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1005.6 Supply plant. See § 1000.6....

  4. 7 CFR 1032.6 - Supply plant.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 9 2013-01-01 2013-01-01 false Supply plant. 1032.6 Section 1032.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1032.6 Supply plant. See § 1000.6....

  5. 7 CFR 1001.6 - Supply plant.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 9 2014-01-01 2013-01-01 true Supply plant. 1001.6 Section 1001.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1001.6 Supply plant. See § 1000.6....

  6. 7 CFR 1007.6 - Supply plant.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 9 2013-01-01 2013-01-01 false Supply plant. 1007.6 Section 1007.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1007.6 Supply plant. See § 1000.6....

  7. 7 CFR 1006.6 - Supply plant.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 9 2013-01-01 2013-01-01 false Supply plant. 1006.6 Section 1006.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1006.6 Supply plant. See § 1000.6....

  8. 7 CFR 1033.6 - Supply plant.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 9 2012-01-01 2012-01-01 false Supply plant. 1033.6 Section 1033.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1033.6 Supply plant. See § 1000.6....

  9. 7 CFR 1005.6 - Supply plant.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 9 2013-01-01 2013-01-01 false Supply plant. 1005.6 Section 1005.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1005.6 Supply plant. See § 1000.6....

  10. 7 CFR 1131.6 - Supply plant.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 9 2014-01-01 2013-01-01 true Supply plant. 1131.6 Section 1131.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Handling Definitions § 1131.6 Supply plant. See § 1000.6....

  11. 7 CFR 1001.6 - Supply plant.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 9 2012-01-01 2012-01-01 false Supply plant. 1001.6 Section 1001.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1001.6 Supply plant. See § 1000.6....

  12. 7 CFR 1131.6 - Supply plant.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 9 2012-01-01 2012-01-01 false Supply plant. 1131.6 Section 1131.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1131.6 Supply plant. See § 1000.6....

  13. 7 CFR 1126.6 - Supply plant.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 9 2012-01-01 2012-01-01 false Supply plant. 1126.6 Section 1126.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Handling Definitions § 1126.6 Supply plant. See § 1000.6....

  14. 7 CFR 1124.6 - Supply plant.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 9 2012-01-01 2012-01-01 false Supply plant. 1124.6 Section 1124.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Definitions § 1124.6 Supply plant. See § 1000.6....

  15. 24 CFR 3280.803 - Power supply.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ...) The power supply to the manufactured home shall be a feeder assembly consisting of not more than one... the end of the cord, including bared leads, to the face of the attachment-plug cap shall not be less... the attachment-plug cap of the power supply cord and any connector cord assembly or receptacle...

  16. 24 CFR 3280.803 - Power supply.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ...) The power supply to the manufactured home shall be a feeder assembly consisting of not more than one... the end of the cord, including bared leads, to the face of the attachment-plug cap shall not be less... the attachment-plug cap of the power supply cord and any connector cord assembly or receptacle...

  17. Pharmaceutical supply chain risks: a systematic review

    PubMed Central

    2013-01-01

    Introduction Supply of medicine as a strategic product in any health system is a top priority. Pharmaceutical companies, a major player of the drug supply chain, are subject to many risks. These risks disrupt the supply of medicine in many ways such as their quantity and quality and their delivery to the right place and customers and at the right time. Therefore risk identification in the supply process of pharmaceutical companies and mitigate them is highly recommended. Objective In this study it is attempted to investigate pharmaceutical supply chain risks with perspective of manufacturing companies. Methods Scopus, PubMed, Web of Science bibliographic databases and Google scholar scientific search engines were searched for pharmaceutical supply chain risk management studies with 6 different groups of keywords. All results found by keywords were reviewed and none-relevant articles were excluded by outcome of interests and researcher boundaries of study within 4 steps and through a systematic method. Results Nine articles were included in the systematic review and totally 50 main risks based on study outcome of interest extracted which classified in 7 categories. Most of reported risks were related to supply and supplier issues. Organization and strategy issues, financial, logistic, political, market and regulatory issues were in next level of importance. Conclusion It was shown that the majority of risks in pharmaceutical supply chain were internal risks due to processes, people and functions mismanagement which could be managed by suitable mitigation strategies. PMID:24355166

  18. Faculty Supply and Demand in Education.

    ERIC Educational Resources Information Center

    Castle, Sharon; Arends, Richard I.

    2003-01-01

    Investigated current levels of faculty supply and demand at 752 American Association of Colleges for Teacher Education member institutions. Survey data indicate that demand is greater than supply, shortages are more critical in some program areas than others (e.g., early childhood and special education), the percentage of minority hires has…

  19. 18 CFR 801.6 - Water supply.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 18 Conservation of Power and Water Resources 2 2010-04-01 2010-04-01 false Water supply. 801.6 Section 801.6 Conservation of Power and Water Resources SUSQUEHANNA RIVER BASIN COMMISSION GENERAL POLICIES § 801.6 Water supply. (a) The Susquehanna River Basin is rich in water resources. With...

  20. 18 CFR 801.6 - Water supply.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 18 Conservation of Power and Water Resources 2 2012-04-01 2012-04-01 false Water supply. 801.6 Section 801.6 Conservation of Power and Water Resources SUSQUEHANNA RIVER BASIN COMMISSION GENERAL POLICIES § 801.6 Water supply. (a) The Susquehanna River Basin is rich in water resources. With...

  1. 18 CFR 801.6 - Water supply.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 18 Conservation of Power and Water Resources 2 2011-04-01 2011-04-01 false Water supply. 801.6 Section 801.6 Conservation of Power and Water Resources SUSQUEHANNA RIVER BASIN COMMISSION GENERAL POLICIES § 801.6 Water supply. (a) The Susquehanna River Basin is rich in water resources. With...

  2. 18 CFR 801.6 - Water supply.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 18 Conservation of Power and Water Resources 2 2014-04-01 2014-04-01 false Water supply. 801.6 Section 801.6 Conservation of Power and Water Resources SUSQUEHANNA RIVER BASIN COMMISSION GENERAL POLICIES § 801.6 Water supply. (a) The Susquehanna River Basin is rich in water resources. With...

  3. 18 CFR 801.6 - Water supply.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 18 Conservation of Power and Water Resources 2 2013-04-01 2012-04-01 true Water supply. 801.6 Section 801.6 Conservation of Power and Water Resources SUSQUEHANNA RIVER BASIN COMMISSION GENERAL POLICIES § 801.6 Water supply. (a) The Susquehanna River Basin is rich in water resources. With...

  4. A MIXTURE OF ORGANOTINS FOUND IN POLYVINYL CHLORIDE (PVC) PIPE IS NOT IMMUNOTOXIC TO SPRAGUE-DAWLEY RATS WHEN GIVEN IN DRINKING WATER

    EPA Science Inventory

    Organotin compounds used in PVC pipe production are of concern to the U.S. EPA because they leach from supply pipes into drinking water and are reported multisystem toxicants. We assessed immune functions in male Sprague-Dawley rats exposed to the mixture of organotins used in P...

  5. Teaching Lean Six Sigma within a Supply Chain Context: The Airplane Supply Chain Simulation

    ERIC Educational Resources Information Center

    Ellis, Scott C.; Goldsby, Thomas J.; Bailey, Ana M.; Oh, Jae-Young

    2014-01-01

    Lean six sigma is a management methodology that firms can employ to achieve substantial improvement in supply chain performance. However, few pedagogical exercises facilitate students' use of a comprehensive set of lean six sigma principles within a supply chain context. We describe the Airplane Supply Chain Simulation that helps students…

  6. New intelligent magnet power supplies for LAMPF

    SciTech Connect

    Cohen, S.; Sturrock, J.

    1991-01-01

    New magnet power supplies are scheduled to be installed in the proton linac at the Clinton P. Anderson Meson Physics Facility (LAMPF). The control and interface design of these power supplies represents a departure from all others onsite. A high-level ASCII control protocol has been designed. The supplies have sophisticated microprocessor control onboard and communicate with the accelerator control system via RS-422 (serial communications). The low-level software used by the accelerator control system is currently being rewritten to accommodate these new devices. They will communicate with the control system through a terminal server port connected to the site-wide ethernet backbone. This means that each supply will, for all intents and purposes, be a network object. Details of the design strategies for the analog and digital control for these supplies as well as the control protocol interface will be presented. 5 refs., 5 figs., 1 tab.

  7. Uncertainty analysis for water supply reservoir yields

    NASA Astrophysics Data System (ADS)

    Kuria, Faith; Vogel, Richard

    2015-10-01

    Understanding the variability of water supply reservoir yields is central for planning purposes. The basis of this study is an empirical global relationship between reservoir storage capacity, water supply yield and reliability based on a global database of 729 rivers. Monte Carlo simulations reveal that the coefficient of variation of estimates of water supply reservoir yields depend only on the length of streamflows record and the coefficient of variation of the streamflows used to estimate the yield. We compare the results of those Monte Carlo experiments with an analytical uncertainty method First Order Variance Approximation (FOVA). FOVA is shown to produce a general, accurate and useful expression for estimating the coefficient of variation of water supply reservoir yield estimates. We also document how the FOVA analytical model can be used to determine the minimum length of streamflow record required during the design of water supply reservoirs so as to ensure that the yield delivered from reservoir falls within a prespecified margin of error.

  8. Coal slurry fuel supply and purge system

    DOEpatents

    McDowell, Robert E.; Basic, Steven L.; Smith, Russel M.

    1994-01-01

    A coal slurry fuel supply and purge system for a locomotive engines is disclosed which includes a slurry recirculation path, a stand-by path for circulating slurry during idle or states of the engine when slurry fuel in not required by the engine, and an engine header fluid path connected to the stand-by path, for supplying and purging slurry fuel to and from fuel injectors. A controller controls the actuation of valves to facilitate supply and purge of slurry to and from the fuel injectors. A method for supplying and purging coal slurry in a compression ignition engine is disclosed which includes controlling fluid flow devices and valves in a plurality of fluid paths to facilitate continuous slurry recirculation and supply and purge of or slurry based on the operating state of the engine.

  9. Essential tools of supply chain management.

    PubMed

    Buddress, L; Raedels, A

    2000-08-01

    At a recent conference, the keynote speaker provoked an incredulous response when he said, "Today, competition among individual firms is dead." He then went on to explain that today, competition is supply chain against supply chain. Whichever firm has the superior supply chain will win out in the marketplace. Given the global marketplace in which we all operate, most of us would agree that his statements are true. How does a firm establish a world-class supply base? What kinds of contracts and agreements are necessary to support the diverse requirements of today's firms? How should a firm select from among the available contract types? These are foundation questions for supply chain management.

  10. Methods and systems for deacidizing gaseous mixtures

    DOEpatents

    Hu, Liang

    2010-05-18

    An improved process for deacidizing a gaseous mixture using phase enhanced gas-liquid absorption is described. The process utilizes a multiphasic absorbent that absorbs an acid gas at increased rate and leads to reduced overall energy costs for the deacidizing operation.

  11. Modeling the chemistry of complex petroleum mixtures.

    PubMed

    Quann, R J

    1998-12-01

    Determining the complete molecular composition of petroleum and its refined products is not feasible with current analytical techniques because of the astronomical number of molecular components. Modeling the composition and behavior of such complex mixtures in refinery processes has accordingly evolved along a simplifying concept called lumping. Lumping reduces the complexity of the problem to a manageable form by grouping the entire set of molecular components into a handful of lumps. This traditional approach does not have a molecular basis and therefore excludes important aspects of process chemistry and molecular property fundamentals from the model's formulation. A new approach called structure-oriented lumping has been developed to model the composition and chemistry of complex mixtures at a molecular level. The central concept is to represent an individual molecular or a set of closely related isomers as a mathematical construct of certain specific and repeating structural groups. A complex mixture such as petroleum can then be represented as thousands of distinct molecular components, each having a mathematical identity. This enables the automated construction of large complex reaction networks with tens of thousands of specific reactions for simulating the chemistry of complex mixtures. Further, the method provides a convenient framework for incorporating molecular physical property correlations, existing group contribution methods, molecular thermodynamic properties, and the structure--activity relationships of chemical kinetics in the development of models.

  12. The Coffee-Milk Mixture Problem Revisited

    ERIC Educational Resources Information Center

    Marion, Charles F.

    2015-01-01

    This analysis of a problem that is frequently posed at professional development workshops, in print, and on the Web--the coffee-milk mixture riddle--illustrates the timeless advice of George Pólya's masterpiece on problem solving in mathematics, "How to Solve It." In his book, Pólya recommends that problems previously solved and put…

  13. A Skew-Normal Mixture Regression Model

    ERIC Educational Resources Information Center

    Liu, Min; Lin, Tsung-I

    2014-01-01

    A challenge associated with traditional mixture regression models (MRMs), which rest on the assumption of normally distributed errors, is determining the number of unobserved groups. Specifically, even slight deviations from normality can lead to the detection of spurious classes. The current work aims to (a) examine how sensitive the commonly…

  14. Ternary gas mixture for diffuse discharge switch

    DOEpatents

    Christophorou, Loucas G.; Hunter, Scott R.

    1988-01-01

    A new diffuse discharge gas switch wherein a mixture of gases is used to take advantage of desirable properties of the respective gases. There is a conducting gas, an insulating gas, and a third gas that has low ionization energy resulting in a net increase in the number of electrons available to produce a current.

  15. Modeling the chemistry of complex petroleum mixtures.

    PubMed Central

    Quann, R J

    1998-01-01

    Determining the complete molecular composition of petroleum and its refined products is not feasible with current analytical techniques because of the astronomical number of molecular components. Modeling the composition and behavior of such complex mixtures in refinery processes has accordingly evolved along a simplifying concept called lumping. Lumping reduces the complexity of the problem to a manageable form by grouping the entire set of molecular components into a handful of lumps. This traditional approach does not have a molecular basis and therefore excludes important aspects of process chemistry and molecular property fundamentals from the model's formulation. A new approach called structure-oriented lumping has been developed to model the composition and chemistry of complex mixtures at a molecular level. The central concept is to represent an individual molecular or a set of closely related isomers as a mathematical construct of certain specific and repeating structural groups. A complex mixture such as petroleum can then be represented as thousands of distinct molecular components, each having a mathematical identity. This enables the automated construction of large complex reaction networks with tens of thousands of specific reactions for simulating the chemistry of complex mixtures. Further, the method provides a convenient framework for incorporating molecular physical property correlations, existing group contribution methods, molecular thermodynamic properties, and the structure--activity relationships of chemical kinetics in the development of models. PMID:9860903

  16. Phase separations in a copolymer copolymer mixture

    NASA Astrophysics Data System (ADS)

    Zhang, Jin-Jun; Jin, Guojun; Ma, Yuqiang

    2006-01-01

    We propose a three-order-parameter model to study the phase separations in a diblock copolymer-diblock copolymer mixture. The cell dynamical simulations provide rich information about the phase evolution and structural formation, especially the appearance of onion-rings. The parametric dependence and physical reason for the domain growth of onion-rings are discussed.

  17. Theoretical Thermodynamics of Mixtures at High Pressures

    NASA Technical Reports Server (NTRS)

    Hubbard, W. B.

    1985-01-01

    The development of an understanding of the chemistry of mixtures of metallic hydrogen and abundant, higher-z material such as oxygen, carbon, etc., is important for understanding of fundamental processes of energy release, differentiation, and development of atmospheric abundances in the Jovian planets. It provides a significant theoretical base for the interpretation of atmospheric elemental abundances to be provided by atmospheric entry probes in coming years. Significant differences are found when non-perturbative approaches such as Thomas-Fermi-Dirac (TFD) theory are used. Mapping of the phase diagrams of such binary mixtures in the pressure range from approx. 10 Mbar to approx. 1000 Mbar, using results from three-dimensional TFD calculations is undertaken. Derivation of a general and flexible thermodynamic model for such binary mixtures in the relevant pressure range was facilitated by the following breakthrough: there exists an accurate nd fairly simple thermodynamic representation of a liquid two-component plasma (TCP) in which the Helmholtz free energy is represented as a suitable linear combination of terms dependent only on density and terms which depend only on the ion coupling parameter. It is found that the crystal energies of mixtures of H-He, H-C, and H-O can be satisfactorily reproduced by the same type of model, except that an effective, density-dependent ionic charge must be used in place of the actual total ionic charge.

  18. Oxidative particle mixtures for groundwater treatment

    DOEpatents

    Siegrist, Robert L.; Murdoch, Lawrence C.

    2000-01-01

    The invention is a method and a composition of a mixture for degradation and immobilization of contaminants in soil and groundwater. The oxidative particle mixture and method includes providing a material having a minimal volume of free water, mixing at least one inorganic oxidative chemical in a granular form with a carrier fluid containing a fine grained inorganic hydrophilic compound and injecting the resulting mixture into the subsurface. The granular form of the inorganic oxidative chemical dissolves within the areas of injection, and the oxidative ions move by diffusion and/or advection, therefore extending the treatment zone over a wider area than the injection area. The organic contaminants in the soil and groundwater are degraded by the oxidative ions, which form solid byproducts that can sorb significant amounts of inorganic contaminants, metals, and radionuclides for in situ treatment and immobilization of contaminants. The method and composition of the oxidative particle mixture for long-term treatment and immobilization of contaminants in soil and groundwater provides for a reduction in toxicity of contaminants in a subsurface area of contamination without the need for continued injection of treatment material, or for movement of the contaminants, or without the need for continuous pumping of groundwater through the treatment zone, or removal of groundwater from the subsurface area of contamination.

  19. Topic Analysis Using a Finite Mixture Model.

    ERIC Educational Resources Information Center

    Li, Hang; Yamanishi, Kenji

    2003-01-01

    Presents a single framework for conducting topic analysis that performs both topic identification and text segmentation. Key characteristics of the framework are: representing a topic by means of a cluster of words closely related to the topic; and employing a stochastic model, called a finite mixture model, to represent a word distribution within…

  20. Evaporation of Liquid Hydrocarbon Mixtures on Titan

    NASA Astrophysics Data System (ADS)

    Luspay-Kuti, Adrienn; Chevrier, V. F.; Rivera-Valentin, E. G.; Singh, S.; Roe, L. A.; Wagner, A.

    2013-10-01

    Besides Earth, Titan is the only other known planetary body with proven stable liquids on its surface. The hydrological cycle of these liquid hydrocarbon mixtures is critical in understanding Titan’s atmosphere and surface features. Evaporation of liquid surface bodies has been indirectly observed as shoreline changes from measurements by Cassini ISS and RADAR (Hayes et al. 2011, Icarus 211, 655-671; Turtle et al. 2011, Science 18, 1414-1417.), but the long seasons of Saturn strongly limit the time span of these observations and their validity over the course of an entire Titan year. Using a novel Titan simulation chamber, the evaporation rate of liquid methane and dissolved nitrogen mixture under Titan surface conditions was derived (Luspay-Kuti et al. 2012, GRL 39, L23203), which is especially applicable to low latitude transient liquids. Polar lakes, though, are expected to be composed of a variety of hydrocarbons, primarily a mixture of ethane and methane (e.g. Cordier et al. 2009, ApJL 707, L128-L131). Here we performed laboratory simulations of ethane-methane mixtures with varying mole fraction under conditions suitable for the polar regions of Titan. We will discuss results specifically addressing the evaporation behavior as the solution becomes increasingly ethane dominated, providing quantitative values for the evaporation rate at every step. These laboratory results are relevant to polar lakes, such as Ontario Lacus, and can shed light on their stability.