Science.gov

Sample records for air-to-cloth ratio baghouse

  1. Selecting baghouse dust collectors

    SciTech Connect

    Moore, S.; Rubak, J.; Jolin, M. |

    1997-04-01

    A thorough analysis of the dust to be captured and determination of specific application requirements are necessary when designing a baghouse collection system. Independent consultants specializing in pollution control equipment and manufacturers with experience in several types of collectors are possible sources of assistance. These experts typically have testing facilities to analyze the dust characteristics. This final article of a two-part series on baghouse design and selection concentrates on application considerations created by the type of dust handled, selecting the best filtration media, selecting the best filtration media, and determining the air-to-cloth (A/C) ratio. The first article discussed bag sizing and cleaning methods and housing and hopper designs.

  2. Baghouse Slipstream Testing at TXU's Big Brown Station

    SciTech Connect

    John Pavlish; Jason Laumb; Robert Jensen; Jeffery Thompson; Christopher Martin; Mark Musich; Brandon Pavlish; Stanley Miller; Lucinda Hamre

    2007-04-30

    Performing sorbent testing for mercury control at a large scale is a very expensive endeavor and requires months of planning and careful execution. Even with good planning, there are plant limitations on what operating/design parameters can be varied/tested and when. For parameters that cannot be feasibly tested at the full scale (lower/higher gas flow, different bag material, cleaning methods, sorbents, etc.), an alternative approach is used to perform tests on a slipstream unit using flue gas from the plant. The advantage that a slipstream unit provides is the flexibility to test multiple operating and design parameters and other possible technology options without risking major disruption to the operation of the power plant. Additionally, the results generated are expected to simulate full-scale conditions closely, since the flue gas used during the tests comes directly from the plant in question. The Energy & Environmental Research Center developed and constructed a mobile baghouse that allows for cost-effective testing of impacts related to variation in operating and design parameters, as well as other possible mercury control options. Multiple sorbents, air-to-cloth ratios, bag materials, and cleaning frequencies were evaluated while flue gas was extracted from Big Brown when it fired a 70% Texas lignite-30% Powder River Basin (PRB) blend and a 100% PRB coal.

  3. The development and testing of a prototype mini-baghouse to control the release of respirable crystalline silica from sand movers.

    PubMed

    Alexander, Barbara M; Esswein, Eric J; Gressel, Michael G; Kratzer, Jerry L; Feng, H Amy; King, Bradley; Miller, Arthur L; Cauda, Emanuele

    2016-08-01

    Inhalation of respirable crystalline silica (RCS) is a significant risk to worker health during well completions operations (which include hydraulic fracturing) at conventional and unconventional oil and gas extraction sites. RCS is generated by pneumatic transfer of quartz-containing sand during hydraulic fracturing operations. National Institute for Occupational Safety and Health (NIOSH) researchers identified concentrations of RCS at hydraulic fracturing sites that exceed 10 times the Occupational Safety and Health Administration (OSHA) Permissible Exposure Limit (PEL) and up to 50 times the NIOSH Recommended Exposure Limit (REL). NIOSH research identified at least seven point sources of dust release at contemporary oil and gas extraction sites where RCS aerosols were generated.  NIOSH researchers recommend the use of engineering controls wherever they can be implemented to limit the RCS released. A control developed to address one of the largest sources of RCS aerosol generation is the NIOSH mini-baghouse assembly, mounted on the thief hatches on top of the sand mover. This article details the results of a trial of the NIOSH mini-baghouse at a sand mine in Arkansas from November 18-21, 2013.  During the trial, area air samples were collected at 12 locations on and around a sand mover with and without the mini-baghouse control installed. Analytical results for respirable dust and RCS indicate the use of the mini-baghouse effectively reduced both respirable dust and RCS downwind of the thief hatches. Reduction of airborne respirable dust ranged from 85-98%; reductions in airborne RCS ranged from 79-99%. A bulk sample of dust collected by the baghouse assembly showed the likely presence of freshly fractured quartz, a particularly hazardous form of RCS.  Planned future design enhancements will increase the performance and durability of the mini-baghouse, including an improved bag clamp mechanism and upgraded filter fabric with a modified air-to-cloth ratio

  4. Selecting baghouse dust collectors

    SciTech Connect

    Moore, S.; Rubak, J.; Jolin, M. |

    1996-10-01

    Control of nuisance or process dusts generated within a plant is a vital concern with today`s growing emphasis on indoor air quality. In the past, many companies simply moved these contaminants away from workers and discharged them into the atmosphere. More stringent pollution control requirements now make this course of action unacceptable. Also, in some cases there is a need to recover high-value dusts, such as chemicals or precious metals. As a result, proper design and selection of a dust collection system are more critical than ever. There are two types of fabric filter dust collection systems commonly used today: baghouses and cartridges. Baghouses were the first collection systems with fabric media (in the form of long tubes, or bags) for removal of contaminants. The versatility of the baghouse--coupled with constant technological refinements--have made it a long-standing favorite among specifiers of pollution control equipment. In fact, baghouses account for more than 80% of all fabric filter dust collection systems in use today. Cartridge dust collectors use rigidly pleated filter elements instead of bags, making it possible to accommodate a large amount of filter surface area in a comparatively small package. Cartridge collectors also offer high efficiency and low pressure drop.

  5. BAGHOUSE FILTRATION PRODUCTS VERIFICATION TESTING, HOW IT BENEFITS THE BOILER BAGHOUSE OPERATOR

    EPA Science Inventory

    The paper describes the Environmental Technology Verification (ETV) Program for baghouse filtration products developed by the Air Pollution Control Technology Verification Center, one of six Centers under the ETV Program, and discusses how it benefits boiler baghouse operators. A...

  6. Baghouse cleans flyash from boiler exhaust

    SciTech Connect

    Not Available

    1981-02-01

    A large baghouse installation recently started up on the boilerhouse of the Avtex Fibers Inc. rayon plant in Front Royal, Virginia. The baghouse removes 99.7% of the flyash particulate from the combustion fumes of five coal-fired boilers. The boilers have a combined capacity of one million lb/h of steam. Emissions from the plant are well below EPA limitations.

  7. The evolution and impact of testing baghouse filter performance.

    PubMed

    Pham, Minh; Clark, Christina; Mckenna, John

    2012-08-01

    In 1995, the US. Environmental Protection Agency (EPA) initiated the Environmental Technology Verification (ETV) program for the purpose of generating both independent and credible performance verification of innovative technologies and helping to accelerate acceptance of these products into the marketplace to further benefit the environment and protect public health. The EPA has approved a testing protocol under this program to verify the performance of commercially available filtration products for pulse-jet baghouses in removingfine particulate matter (aerodynamic diameter<2.5 microm; PM2.5). This verification testing protocol was later used as a basis for the development of the American Society for Testing and Materials (ASTM) Method D6830-02 and the International Organization for Standardization (ISO) Method 11057. The South Coast Air Quality Management District (SCAQMD) in California and the EPA s Office of Air Quality Planning and Standards (OAQPS) highly encourage the use of ETV/ASTM-verified filtration media. This paper highlights the evolution of the standard test methods, the EPA's and SCAQMD's regulatory activities, the benefits of using verified filtration media, and the importance of including the filter performance testing in future consideration of baghouse permitting, baghouse operation and maintenance (O&M) plans, quality assurance/quality control (QA/QC), and bag monitoring plans.

  8. Using fume silica as heavy metals' stabilizer for high alkali and porous MSWI baghouse ash.

    PubMed

    Huang, Wu-Jang; Huang, Hung-Shao

    2008-03-21

    In this study, we have proved that heavy metals in high porous and alkali baghouse ash could be fixed effectively by fume silica powder alone, or with the incorporation of colloidal aluminum oxide (CAO). The optimum amount is about 100g of fume silica per kilogram of baghouse ash. Results have indicated that fume silica has a better fixation efficiency of lead in high porous baghouse ash. In addition, the reaction mechanism of fume silica is also discussed.

  9. Modeling sorbent injection for mercury control in baghouse filters: I--model development and sensitivity analysis.

    PubMed

    Flora, Joseph R V; Hargis, Richard A; O'Dowd, William J; Pennline, Henry W; Vidic, Radisav D

    2003-04-01

    A two-stage mathematical model for Hg removal using powdered activated carbon injection upstream of a baghouse filter was developed, with the first stage accounting for removal in the ductwork and the second stage accounting for additional removal caused by the retention of carbon particles on the filter. The model shows that removal in the ductwork is minimal, and the additional carbon detention time from the entrapment of the carbon particles in the fabric filter enhances the Hg removal from the gas phase. A sensitivity analysis on the model shows that Hg removal is dependent on the isotherm parameters, the carbon pore radius and tortuosity, the C/Hg ratio, and the carbon particle radius.

  10. Environmental Technology Verification; Baghouse Filtration Products TTG Inc., TG100 Filtration Media (Tested August 2012)

    EPA Science Inventory

    Baghouses are air pollution control devices used to control particulate emissions from stationary sources and are among the technologies evaluated by the APCT Center. Baghouses and their accompanying filter media have long been one of the leading particulate control techniques fo...

  11. Environmental Technology Verification, Baghouse Filtration Products TTG Inc., TG800 Filtration Media (Tested August 2012)

    EPA Science Inventory

    Baghouses are air pollution control devices used to control particulate emissions from stationary sources and are among the technologies evaluated by the APCT Center. Baghouses and their accompanying filter media have long been one of the leading particulate control techniques fo...

  12. Using high temperature baghouses to enhance desulfurization following economizer sorbent injection

    SciTech Connect

    Li, G.; Keener, T.C.

    1995-12-31

    In order to explore the potential of using high temperature baghouses to enhance SO{sub 2} removal following upstream sorbent injection, an integrated two-stage reactor system has been built. It consists of an injection stage and a filtration stage. Distinct from one-stage fixed-bed reactors, sorbent particles in this system are initially converted under controlled injection conditions before entering the filtration reactor chamber. By the aid of the system, several unique features regarding the gas-solid reactions in the baghouse after economizer zone sorbent injection have been revealed. Results have shown that the appropriate usage of a high temperature baghouse may substantially enhance the performance of the process. The further SO{sub 2} removal in the baghouse is comprehensively affected by both the conditions in the injection zone and those in the baghouse.

  13. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT - BAGHOUSE FILTRATION PRODUCTS - BHA GROUP, INC. QG061 FILTER SAMPLE

    EPA Science Inventory

    Baghouse filtration products (BFPs) were evaluated by the Air Pollution Control Technology (APCT) pilot of the Environmental Technology Verification (ETV) Program. The performance factor verified was the mean outlet particle concentration for the filter fabric as a function of th...

  14. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT - BAGHOUSE FILTRATION PRODUCTS - INSPEC FIBRES 5512BRF FILTER SAMPLE

    EPA Science Inventory

    Baghouse filtration products (BFPs) were evaluated by the Air Pollution Control Technology (APCT) pilot of the Environmental Technology Verification (ETV) Program. The performance factor verified was the mean outlet particle concentration for the filter fabric as a function of th...

  15. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT - BAGHOUSE FILTRATION PRODUCTS - STANDARD FILTER CORPORATION PE16ZU FILTER SAMPLE

    EPA Science Inventory

    Baghouse filtration products (BFPs) were evaluated by the Air Pollution Control Technology (APCT) pilot of the Environmental Technology Verification (ETV) Program. The performance factor verified was the mean outlet particle concentration for the filter fabric as a function of th...

  16. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT - BAGHOUSE FILTRATION PRODUCTS - TETRATEC PTFE TECHNOLOGIES TETRATEX 8005

    EPA Science Inventory

    Baghouse filtration products (BFPs) were evaluated by the Air Pollution Control Technology (APCT) pilot of the Environmental Technology Verification (ETV) Program. The performance factor verified was the mean outlet particle concentration for the filter fabric as a function of th...

  17. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT - BAGHOUSE FILTRATION PRODUCTS - AIR PURATOR CORPORATION HUYGLAS 1405M FILTER SAMPLE

    EPA Science Inventory

    Baghouse filtration products (BFPs) were evaluated by the Air Pollution Control Technology (APCT) pilot of the Environmental Technology Verification (ETV) Program. The performance factor verified was the mean outlet particle concentration for the filter fabric as a function of th...

  18. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT - BAGHOUSE FILTRATION PRODUCTS - MENARDI-CRISWELL 50-504 FILTER SAMPLE

    EPA Science Inventory

    Baghouse filtration products (BFPs) were evaluated by the Air Pollution Control Technology (APCT) pilot of the Environmental Technology Verification (ETV) Program. The performance factor verified was the mean outlet particle concentration for the filter fabric as a function of th...

  19. Mineral phases and metals in baghouse dust from secondary ...

    EPA Pesticide Factsheets

    Baghouse dust (BHD) is a solid waste generated by air pollution control systems during secondary aluminum processing (SAP). Management and disposal of BHD can be challenging in the U.S. and elsewhere. In this study, the mineral phases, metal content and metal leachability of 78 BHD samples collected from 13 different SAP facilities across the U.S. were investigated. The XRD semi-quantitative analysis of BHD samples suggests the presence of metallic aluminum, aluminum oxide, aluminum nitride and its oxides, spinel, elpasolite as well as diaspora. BHD also contains halite, sylvite and fluorite, which are used as fluxes in SAP activities. Total aluminum (Al) in the BHD samples averaged 18% by weight. Elevated concentrations of trace metals (>100 µgL-1 As; >1000 µgL-1 Cu, Mn, Se, Pb, Mn and Zn) were also detected in the leachate. The U.S. toxicity characteristic leaching procedure (TCLP) results showed that some samples leached above the toxicity limit for Cd, Pb and Se. Exceeding the TCLP limits in all sample is independent of facilities generating the BHD. From the metal content perspective only, it appears that BHD has a higher potential to exhibit toxicity characteristics than salt cake (the largest waste stream generated by SAP facilities). The objective of this study was to investigate BHD from SAP facilities in the U.S. by determining the mineral phases and the metal (Al, As, Ca, Cd, Cr, Cu, Fe, K, Mg, Mn, Na, Pb, Se and Zn) content of the sample

  20. Effect of flow distributors on uniformity of velocity profile in a baghouse.

    PubMed

    Chen, Chi-Jen; Cheng, Man-Ting

    2005-07-01

    In recent years, the utility industry has turned to baghouses as an alternative technology for particulate emission control from pulverized-coal-fired power plants. One of the more significant issues is to improve poor gas distribution that causes bag failures in baghouse operation. Bag failures during operation are almost impossible to prevent, but proper flow design can help in their prevention. This study investigated vertical velocity profiles below the bags in a baghouse (the hopper region) to determine whether flow could be improved with the installation of flow distributors in the hopper region. Three types of flow distributors were used to improve flow distribution and were compared with the original baghouse without flow distributors. Velocity profiles were measured by a hot-wire anemometer at an inlet velocity of 18 m/sec. Uniformity of flow distribution was calculated by the uniformity value U for the velocity profile of each flow distributor. Experimental results showed that the velocity profile of the empty configuration (without flow distributors) was poor because the uniformity value was 2.048. The uniformity values of type 1 (flow distributor with three vertical vanes), type 2 (flow distributor with one vertical and one inclined vane), and type 3 (flow distributor with two inclined vanes) configurations were reduced to 1.051, 0.617, and 0.526, respectively. These results indicate that the flow distributors designed in this study made significant improvements in the velocity profile of a baghouse, with the type 3 configuration having the best performance.

  1. Donaldson Company, Inc., Dura-Life #0701607 Filtration Media(Tested October 2011) (ETV Baghouse Filtration Products) Verification Report

    EPA Science Inventory

    Baghouses are air pollution control devices used to control particulate emissions from stationary sources and are among the technologies evaluated by the APCT Center. Baghouses and their accompanying filter media have long been one of the leading particulate control techniques fo...

  2. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT, BAGHOUSE FILTRATION PRODUCTS, BHA GROUP, INC., QP131 FILTER SAMPLE

    EPA Science Inventory

    Baghouse filtration products (BFPs) were evaluated by the Air Pollution Control Technology (APCT) Verification Center. The performance factor verified was the mean outlet particle concentration for the filter fabric as a function of the size of those particles equal to and smalle...

  3. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT, BAGHOUSE FILTRATION PRODUCTS, POLYMER GROUP, INC., DURAPEX PET FILTER SAMPLE

    EPA Science Inventory

    Baghouse filtration products (BFPs) were evaluated by the Air Pollution Control Technology (APCT) Verification Center. The performance factor verified was the mean outlet particle concentration for the filter fabric as a function of the size of those particles equal to and smalle...

  4. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT, BAGHOUSE FILTRATION PRODUCTS, TETRATEC PTFE PRODUCTS, TETRATEX 6212 FILTER SAMPLE

    EPA Science Inventory

    Baghouse filtration products (BFPs) were evaluated by the Air Pollution Control Technology (APCT) Verification Center. The performance factor verified was the mean outlet particle concentration for the filter fabric as a function of the size of those particles equal to and smalle...

  5. Mineral phases and metals in baghouse dust from secondary aluminum production

    EPA Science Inventory

    Baghouse dust (BHD) is a solid waste generated by air pollution control systems during secondary aluminum processing (SAP). Management and disposal of BHD can be challenging in the U.S. and elsewhere. In this study, the mineral phases, metal content and metal leachability of 78...

  6. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT - BAGHOUSE FILTRATION PRODUCTS - BASF CORPORATION AX/BA-14/9-SAXP FILTER SAMPLE

    EPA Science Inventory

    Baghouse filtration products (BFPs) were evaluated by the Air Pollution Control Technology (APCT) pilot of the Environmental Technology Verification (ETV) Program. The performance factor verified was the mean outlet particle concentration for the filter fabric as a function of th...

  7. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT - BAGHOUSE FILTRATION PRODUCTS - W.L. GORE & ASSOCIATES, INC. L4347 FILTER SAMPLE

    EPA Science Inventory

    Baghouse filtration products (BFPs) were evaluated by the Air Pollution Control Technology (APCT) pilot of the Environmental Technology Verification (ETV) Program. The performance factor verified was the mean outlet particle concentration for the filter fabric as a function of th...

  8. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT - BAGHOUSE FILTRATION PRODUCTS - ALBANY INTERNATIONAL CORP. INDUSTRIAL PROCESS TECHNOLOGIES PRIMATEX PLUS I FILTER SAMPLE

    EPA Science Inventory

    Baghouse filtration products (BFPs) were evaluated by the Air Pollution Control Technology (APCT) pilot of the Environmental Technology Verification (ETV) Program. The performance factor verified was the mean outlet particle concentration for the filter fabric as a function of th...

  9. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT: BAGHOUSE FILTRATION PRODUCTS—SOUTHERN FILTER MEDIA, LLC, PE-16/M-SPES FILTER SAMPLE

    EPA Science Inventory

    The U.S. EPA has created the Environmental Technology Verification program to facilitate the deployment of innovative or improved environmental technologies through performance verification and dissemination of information. The program tested the performance of baghouse filtrati...

  10. Size-dependent penetration of trace elements through a utility baghouse

    NASA Astrophysics Data System (ADS)

    Shendrikar, A. D.; Ensor, D. S.; Cowen, S. J.; Woffinden, G. J.; McElroy, M. W.

    Particle size-dependent concentrations of 35 major and minor trace elements were measured at the inlet and outlet of a fabric filter baghouse installed on a western pulverized coal-fired power plant. Size-segregated particulate samples were collected using University of Washington impactors with Kapton collection disks coated with Apiezon-L grease. The impactor samples were analyzed for trace elements using neutron activation analysis. The inlet particle size distribution for most elements was bimodal, with the larger mode having a geometric mean diameter of approximately 4-10 μm and the smaller mode having a geometric mean diameter of 0.08 μm or less. In general, individual trace elements exhibited size distributions similar to total mass. However, several elements, including As, Se, Sb, Hg, Cl, Zn and Ni, showed noticeably 'flatter' size distributions with proportionally higher concentrations in submicrometer particles compared to total mass. The elemental penetrations through the baghouse generally agreed well with the mass penetration. An exception is Se, which shows penetration an order of magnitude higher than that of total mass and other elements. Most trace elements were removed by the baghouse with greater than 95 % collection efficiency over the entire particle size range.

  11. Ratio

    NASA Astrophysics Data System (ADS)

    Webster, Nathan A. S.; Pownceby, Mark I.; Madsen, Ian C.; Studer, Andrew J.; Manuel, James R.; Kimpton, Justin A.

    2014-12-01

    Effects of basicity, B (CaO:SiO2 ratio) on the thermal range, concentration, and formation mechanisms of silico-ferrite of calcium and aluminum (SFCA) and SFCA-I iron ore sinter bonding phases have been investigated using an in situ synchrotron X-ray diffraction-based methodology with subsequent Rietveld refinement-based quantitative phase analysis. SFCA and SFCA-I phases are the key bonding materials in iron ore sinter, and improved understanding of the effects of processing parameters such as basicity on their formation and decomposition may assist in improving efficiency of industrial iron ore sintering operations. Increasing basicity significantly increased the thermal range of SFCA-I, from 1363 K to 1533 K (1090 °C to 1260 °C) for a mixture with B = 2.48, to ~1339 K to 1535 K (1066 °C to 1262 °C) for a mixture with B = 3.96, and to ~1323 K to 1593 K (1050 °C to 1320 °C) at B = 4.94. Increasing basicity also increased the amount of SFCA-I formed, from 18 wt pct for the mixture with B = 2.48 to 25 wt pct for the B = 4.94 mixture. Higher basicity of the starting sinter mixture will, therefore, increase the amount of SFCA-I, considered to be more desirable of the two phases. Basicity did not appear to significantly influence the formation mechanism of SFCA-I. It did, however, affect the formation mechanism of SFCA, with the decomposition of SFCA-I coinciding with the formation of a significant amount of additional SFCA in the B = 2.48 and 3.96 mixtures but only a minor amount in the highest basicity mixture. In situ neutron diffraction enabled characterization of the behavior of magnetite after melting of SFCA produced a magnetite plus melt phase assemblage.

  12. Determination of dry carbon-based sorbent injection for mercury control in utility ESP and baghouses

    SciTech Connect

    Broderick, T.; Haythornthwaite, S.; Bell, W.; Selegue, T.; Perry, M.

    1998-12-31

    Domestic coal-fired power plants emit approximately 40 to 80 metric tons of mercury to the atmosphere annually. The mercury concentration in utility flue gas is in the dilute range of 0.1 to 1 parts per billion. The EPA is assessing whether such low concentrations of mercury emissions from coal-fired utilities pose any significant health risk and whether mercury regulations would be necessary or appropriate. In anticipation of possible mercury control regulations, ADA Technologies (ADA) and TDA Research, Inc (TDA) were funded by the Department of Energy (DOE) to evaluate carbon-based sorbents for mercury control at utility coal-fired power plants. Past investigations of the use of dry carbon-based sorbent injection for mercury control on pilot-scale utility flue gas applications have shown that these sorbents are capable of removing gas-phase mercury. ADA Technologies field-tested the mercury removal capability of several carbon-based sorbents manufactured by TDA. The test facility was a DOE-owned test facility built and operated by ADA at the Public Service Company of Colorado`s Comanche Station in Pueblo, Colorado. The pilot-scale test fixture is a 600-acfm particulate control module that can be configured as an electrostatic precipitator, a pulse-jet baghouse, or a reverse-gas baghouse. It extracts a slipstream of flue gas from a coal-fired utility boiler. Sorbent is injected into the flue gas slipstream upstream of the particulate control module and is removed by the module. ADA evaluated the mercury capture efficiency of the sorbents over a range of flue gas temperatures and injection rates. In addition, the effect of flyash on mercury capture was also investigated. The test facility is configured to take flue gas from either upstream or downstream of Comanche Station`s full-scale reverse-gas baghouse, allowing tests to be conducted with normal-ash or low-ash flue gas.

  13. The role of pressure drop and flow redistribution on modeling mercury control using sorbent injection in baghouse filters.

    PubMed

    Flora, Joseph R V; Hargis, Richard A; O'Dowd, William J; Karash, Andrew; Pennline, Henry W; Vidic, Radisav D

    2006-03-01

    A mathematical model based on simple cake filtration theory was coupled to a previously developed two-stage mathematical model for mercury (Hg) removal using powdered activated carbon injection upstream of a baghouse filter. Values of the average permeability of the filter cake and the filter resistance extracted from the model were 4.4 x 10(-13) m2 and 2.5 x 10(-4) m(-1), respectively. The flow is redistributed during partial cleaning of the filter, with flows higher across the newly cleaned filter section. The calculated average Hg removal efficiency from the baghouse is lower because of the high mass flux of Hg exiting the filter in the newly cleaned section. The model shows that calculated average Hg removal is affected by permeability, filter resistance, fraction of the baghouse cleaned, and cleaning interval.

  14. The role of pressure drop and flow redistribution on modeling mercury control using sorbent injection in baghouse filters

    SciTech Connect

    Joseph R.V. Flora; Richard A. Hargis; William J. O'Dowd; Andrew Karash; Henry W. Pennline; Radisav D. Vidic

    2006-03-15

    A mathematical model based on simple cake filtration theory was coupled to a previously developed two-stage mathematical model for mercury (Hg) removal from coal combustion using powdered activated carbon injection upstream of a baghouse filter. Values of the average permeability of the filter cake and the filter resistance extracted from the model were 4.4 x 10{sup -13}m{sup 2} and 2.5 x 10{sup -4}m{sup -1}, respectively. The flow is redistributed during partial cleaning of the filter, with flows higher across the newly cleaned filter section. The calculated average Hg removal efficiency from the baghouse is lower because of the high mass flux of Hg exiting the filter in the newly cleaned section. The model shows that calculated average Hg removal is affected by permeability, filter resistance, fraction of the baghouse cleaned, and cleaning interval. 17 refs., 8 figs., 2 tabs.

  15. Environmental Technology Verification Report and Statement for Baghouse Filtration Products, W. L. Gore & Associates, Inc. 5117 High Durability PPS Laminate Filtration Media (Tested March-April 2012)

    EPA Science Inventory

    Baghouses are air pollution control devices used to control particulate emissions from stationary sources and are among the technologies evaluated by the APCT Center. Baghouses and their accompanying filter media have long been one of the leading particulate control techniques fo...

  16. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT, BAGHOUSE FILTRATION PRODUCTS, W.L. GORE & ASSOCIATES, INC., L4427 FILTER SAMPLE

    EPA Science Inventory

    Baghouse filtration products (BFPs) were evaluated by the Air Pollution Control Technology (APCT) Verification Center. The performance factor verified was the mean outlet particle concentration for the filter fabric as a function of the size of those particles equal to and smalle...

  17. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT: BAGHOUSE FILTRATION PRODUCTS, BWF AMERICA, INC. GRADE 700 MPS POLYESTER FELT FILTER SAMPLE

    EPA Science Inventory

    Baghouse filtration products (BFPs) were evaluated by the Air Pollution Control Technology (APCT) Verification Center. The performance factor verified was the mean outlet particle concentration for the filter fabric as a function of the size for particles equal to or smaller than...

  18. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT: BAGHOUSE FILTRATION PRODUCTS, W.L. GORE & ASSOCIATES, INC. LYSB3 FILTER SAMPLE

    EPA Science Inventory

    Baghouse filtration products (BFPs) were evaluated by the Air Pollution Control Technology (APCT) Verification Center. The performance factor verified was the mean outlet particle concentration for the filter fabric as a function of the size for particles equal to or smaller than...

  19. Hydrometallurgical process for recovering iron sulfate and zinc sulfate from baghouse dust

    DOEpatents

    Zaromb, S.; Lawson, D.B.

    1994-02-15

    A process for recovering zinc-rich and iron-rich fractions from the baghouse dust that is generated in various metallurgical operations, especially in steel-making and other iron-making plants, comprises the steps of leaching the dust by hot concentrated sulfuric acid so as to generate dissolved zinc sulfate and a precipitate of iron sulfate, separating the precipitate from the acid by filtration and washing with a volatile liquid, such as methanol or acetone, and collecting the filtered acid and the washings into a filtrate fraction. The volatile liquid may be recovered by distillation, and the zinc may be removed from the filtrate by alternative methods, one of which involves addition of a sufficient amount of water to precipitate hydrated zinc sulfate at 10 C, separation of the precipitate from sulfuric acid by filtration, and evaporation of water to regenerate concentrated sulfuric acid. The recovery of iron may also be effected in alternative ways, one of which involves roasting the ferric sulfate to yield ferric oxide and sulfur trioxide, which can be reconverted to concentrated sulfuric acid by hydration. The overall process should not generate any significant waste stream. 1 figure.

  20. Hydrometallurgical process for recovering iron sulfate and zinc sulfate from baghouse dust

    DOEpatents

    Zaromb, Solomon; Lawson, Daniel B.

    1994-01-01

    A process for recovering zinc/rich and iron-rich fractions from the baghouse dust that is generated in various metallurgical operations, especially in steel-making and other iron-making plants, comprises the steps of leaching the dust by hot concentrated sulfuric acid so as to generate dissolved zinc sulfate and a precipitate of iron sulfate, separating the precipitate from the acid by filtration and washing with a volatile liquid, such as methanol or acetone, and collecting the filtered acid and the washings into a filtrate fraction. The volatile liquid may be recovered distillation, and the zinc may be removed from the filtrate by alternative methods, one of which involves addition of a sufficient amount of water to precipitate hydrated zinc sulfate at 10.degree. C., separation of the precipitate from sulfuric acid by filtration, and evaporation of water to regenerate concentrated sulfuric acid. The recovery of iron may also be effected in alternative ways, one of which involves roasting the ferric sulfate to yield ferric oxide and sulfur trioxide, which can be reconverted to concentrated sulfuric acid by hydration. The overall process should not generate any significant waste stream.

  1. Evaluation of ASD systems for electric arc furnace and argon oxygen decarburization refiner baghouse fans. Final report

    SciTech Connect

    1997-11-01

    Adjustable speed drive (ASD) control of the baghouse fans for Electric Arc Furnace (EAF) and Argon Oxygen Decarburization Vessel (AOD) can improve operations, reduce the degree of dust generation, and provide significant energy savings. The purpose of the project was to quantify the benefits, both in energy savings and other process improvements and to demonstrate the methodology of applying adjustable speed drives, to two baghouse fans from a system perspective. The report describes the approach to accomplishing the ASD equipment installation, the test procedure and methodology and provides the test results and economic return. The test results indicated that by using ASDs to control the extraction fan air flow for the EAF and AOD, the following benefits would be achieved on an annual basis: EAF annual energy savings, 267,929 kWh valued at $11,575; EAF dust reduction, overall, 2--3%; EAF dust reduction, during the flatbath period, 35%; and AOD annual energy savings, 1,443,078 kWh valued at $62,341.

  2. The potential of pulse-jet baghouses for utility boilers. Part 2: Performance of pulse-jet fabric filter pilot plants

    SciTech Connect

    Bustard, C. ); Cushing, K.M. ); Chang, R.L. )

    1992-09-01

    Pulse-jet fabric filters (PJFFs) are widely used in U.S. industrial boiler applications and in utility and industrial boilers abroad. Their small size and reduced cost relative to more conventional reverse-gas baghouses makes the use of PJFFs appear to be an attractive particulate control option for utility boilers. This paper (Part 2 of a three-part series) summarizes the results of pilot PJFF studies sponsored by the Electric Power Research Institute at different utility sites in the United States. The purpose of these tests is to evaluate PJFF performance for U.S. fossil-fuel fired applications. These data are also used to corroborate the results of a recent worldwide survey of PJFF user experience, as described in Part 1 of this series. Part 3 will provide a cost comparison of PJFFs to other particulate control options such as electrostatic precipitators and reverse-gas baghouses. 30 refs., 6 figs., 5 tabs.

  3. Investigation and demonstration of dry carbon-based sorbent injection for mercury control. Quarterly technical report, April 1--June 30, 1996

    SciTech Connect

    Hunt, T.; Sjostrom, S.; Smith, J.; Chang, R.

    1996-07-27

    The overall objective this two phase program is to investigate the use of dry carbon-based sorbents for mercury control. During Phase 1, a bench-scale field test device that can be configured as an electrostatic precipitator, a pulse-jet baghouse, or a reverse-gas baghouse has been designed and will be integrated with an existing pilot-scale facility at PSCo`s Comanche Station. Up to three candidate sorbents will then be injected into the flue gas stream upstream of the test device to determine the mercury removal efficiency for each sorbent. During the Phase 11 effort, component integration for the most promising dry sorbent technology (technically and economically feasible) shall be tested at the 5000 acfm pilot-scale. An extensive work plan has been developed for the project. Three sorbents will be selected for evaluation at the facility through investigation, presentation, and discussion among team members: PSCO, EPRI, ADA, and DOE. The selected sorbents will be tested in the five primary bench-scale configurations: pulse `et baghouse, TOXECON, reverse-gas baghouse, electrostatic precipitator, and an ESP or fabric filter `with no Comanche ash in the flue gas stream. In the EPRI TOXECON system, mercury sorbents will be injected downstream of a primary particulate control device, and collected in a pulse-jet baghouse operated at air-to-cloth ratios of 12 to 16 ft/min, thus separating the mercury and sorbent from the captured flyash. In the no-ash configuration, an external flyash sample will be injected into a clean gas stream to investigate possible variations in sorbent effectiveness in the presence of different ashes. The use of an existing test facility, a versatile design for the test fixture, and installation of a continuous mercury analyzer will allow for the completion of this ambitious test plan. The primary activity during the quarter was to complete fabrication and installation of the facility.

  4. FIELD TEST PROGRAM FOR LONG-TERM OPERATION OF A COHPAC SYSTEM FOR REMOVING MERCURY FROM COAL-FIRED FLUE GAS

    SciTech Connect

    Jean Bustard

    2003-06-13

    long term effects of sorbent injection on mercury capture and COHPAC performance. The work is being done on 1/2 of the gas stream at Alabama Power's Plant Gaston Unit 3 (nominally 135 MW). Data from the testing will be used to determine: (1) Is sorbent injection into a high air-to-cloth ratio baghouse a viable, long term approach for mercury control; and (2) Design criteria and costs for new baghouse/sorbent injection systems that will use a similar, polishing baghouse (TOXECON) approach.

  5. Field Test Program for Long-Term Operation of a COHPAC System for Removing Mercury from Coal-Fired Flue Gas

    SciTech Connect

    Jean Bustard; Charles Lindsey; Paul Brignac; Travis Starns; Sharon Sjostrom; Trent Taylor; Cindy Larson

    2005-01-24

    generating plant that is equipped with a COHPAC{reg_sign} system. The overall objective is to evaluate the long-term effects of sorbent injection on mercury capture and COHPAC{reg_sign} performance. The work is being done on one-half of the gas stream at Alabama Power Company's Plant Gaston Unit 3 (nominally 135 MW). Data from the testing will be used to determine: (1) If sorbent injection into a high air-to-cloth ratio baghouse is a viable, long-term approach for mercury control; and (2) Design criteria and costs for new baghouse/sorbent injection systems that will use a similar, polishing baghouse (TOXECON{trademark}) approach.

  6. Field Test Program for Long-Term Operation of a COHPAC System for Removing Mercury from Coal-Fired Flue Gas

    SciTech Connect

    Jean Bustard; Charles Lindsey; Paul Brignac; Travis Starns; Sharon Sjostrom; Trent Taylor; Cindy Larson

    2004-08-06

    generating plant that is equipped with a COHPAC{reg_sign} system. The overall objective is to evaluate the long-term effects of sorbent injection on mercury capture and COHPAC{reg_sign} performance. The work is being done on one-half of the gas stream at Alabama Power Company's Plant Gaston Unit 3 (nominally 135 MW). Data from the testing will be used to determine: (1) If sorbent injection into a high air-to-cloth ratio baghouse is a viable, long-term approach for mercury control; and (2) Design criteria and costs for new baghouse/sorbent injection systems that will use a similar, polishing baghouse (TOXECON{trademark}) approach.

  7. FIELD TEST PROGRAM FOR LONG-TERM OPERATION OF A COHPAC SYSTEM FOR REMOVING MERCURY FROM COAL-FIRED FLUE GAS

    SciTech Connect

    Jean Bustard; Charles Lindsey; Paul Brignac; Travis Starns; Sharon Sjostrom; Trent Taylor; Cindy Larson

    2003-10-31

    system. The overall objective is to evaluate the long-term effects of sorbent injection on mercury capture and COHPAC performance. The work is being done on one-half of the gas stream at Alabama Power Company's Plant Gaston Unit 3 (nominally 135 MW). Data from the testing will be used to determine: (1) If sorbent injection into a high air-to-cloth ratio baghouse is a viable, long-term approach for mercury control; and (2) Design criteria and costs for new baghouse/sorbent injection systems that will use a similar, polishing baghouse (TOXECON{trademark}) approach.

  8. FIELD TEST PROGRAM FOR LONG-TERM OPERATION OF A COHPAC SYSTEM FOR REMOVING MERCURY FROM COAL-FIRED FLUE GAS

    SciTech Connect

    Jean Bustard; Charles Lindsey

    2003-01-24

    long term effects of sorbent injection on mercury capture and COHPAC performance. The work is being done on 1/2 of the gas stream at Alabama Power's Plant Gaston Unit 3 (nominally 135 MW). Data from the testing will be used to determine: (1) Is sorbent injection into a high air-to-cloth ratio baghouse a viable, long term approach for mercury control; and (2) Design criteria and costs for new baghouse/sorbent injection systems that will use a similar, polishing baghouse (TOXECON) approach.

  9. Field Test Program for Long-Term Operation of a COHPAC System for Removing Mercury from Coal-Fired Flue Gas

    SciTech Connect

    Jean Bustard; Charles Lindsey; Paul Brignac; Travis Starns; Sharon Sjostrom; Cindy Larson

    2006-01-27

    generating plant that is equipped with a COHPAC{reg_sign} system. The overall objective is to evaluate the long-term effects of sorbent injection on mercury capture and COHPAC{reg_sign} performance. The work is being done on one-half of the gas stream at Alabama Power Company's Plant Gaston Unit 3 (nominally 135 MW). Data from the testing will be used to determine: (1) If sorbent injection into a high air-to-cloth ratio baghouse is a viable, long-term approach for mercury control; and (2) Design criteria and costs for new baghouse/sorbent injection systems that will use a similar, polishing baghouse (TOXECON{trademark}) approach.

  10. FIELD TEST PROGRAM FOR LONG-TERM OPERATION OF A COHPAC SYSTEM FOR REMOVING MERCURY FROM COAL-FIRED FLUE GAS

    SciTech Connect

    Jean Bustard; Charles Lindsey; Paul Brignac; Travis Starns; Sharon Sjostrom; Trent Taylor; Cindy Larson

    2004-01-29

    generating plant that is equipped with a COHPAC{trademark} system. The overall objective is to evaluate the long-term effects of sorbent injection on mercury capture and COHPAC{trademark} performance. The work is being done on one-half of the gas stream at Alabama Power Company's Plant Gaston Unit 3 (nominally 135 MW). Data from the testing will be used to determine: (1) If sorbent injection into a high air-to-cloth ratio baghouse is a viable, long-term approach for mercury control; and (2) Design criteria and costs for new baghouse/sorbent injection systems that will use a similar, polishing baghouse (TOXECON{trademark}) approach.

  11. Field Test Program for Long-Term Operation of a COHPAC System for Removing Mercury from Coal-Fired Flue Gas

    SciTech Connect

    Jean Bustard; Charles Lindsey; Paul Brignac; Travis Starns; Sharon Sjostrom; Trent Taylor; Cindy Larson

    2004-06-04

    generating plant that is equipped with a COHPAC{reg_sign} system. The overall objective is to evaluate the long-term effects of sorbent injection on mercury capture and COHPAC{reg_sign} performance. The work is being done on one-half of the gas stream at Alabama Power Company's Plant Gaston Unit 3 (nominally 135 MW). Data from the testing will be used to determine: (1) If sorbent injection into a high air-to-cloth ratio baghouse is a viable, long-term approach for mercury control; and (2) Design criteria and costs for new baghouse/sorbent injection systems that will use a similar, polishing baghouse (TOXECON{trademark}) approach.

  12. Field Test Program for Long-Term Operation of a COHPAC System for Removing Mercury from Coal-Fired Flue Gas

    SciTech Connect

    Jean Bustard; Charles Lindsey; Paul Brignac; Travis Starns; Sharon Sjostrom; Cindy Larson

    2005-07-14

    generating plant that is equipped with a COHPAC{reg_sign} system. The overall objective is to evaluate the long-term effects of sorbent injection on mercury capture and COHPAC{reg_sign} performance. The work is being done on one-half of the gas stream at Alabama Power Company's Plant Gaston Unit 3 (nominally 135 MW). Data from the testing will be used to determine: (1) If sorbent injection into a high air-to-cloth ratio baghouse is a viable, long-term approach for mercury control; and (2) Design criteria and costs for new baghouse/sorbent injection systems that will use a similar, polishing baghouse (TOXECON{trademark}) approach.

  13. Field Test Program for Long-Term Operation of a COHPAC System for Removing Mercury from Coal-Fired Flue Gas

    SciTech Connect

    Jean Bustard; Charles Lindsey; Paul Brignac; Travis Starns; Sharon Sjostrom; Trent Taylor; Cindy Larson

    2004-10-25

    generating plant that is equipped with a COHPAC{reg_sign} system. The overall objective is to evaluate the long-term effects of sorbent injection on mercury capture and COHPAC{reg_sign} performance. The work is being done on one-half of the gas stream at Alabama Power Company's Plant Gaston Unit 3 (nominally 135 MW). Data from the testing will be used to determine: (1) If sorbent injection into a high air-to-cloth ratio baghouse is a viable, long-term approach for mercury control; and (2) Design criteria and costs for new baghouse/sorbent injection systems that will use a similar, polishing baghouse (TOXECON{trademark}) approach.

  14. Field Test Program for Long-Term Operation of a COHPAC System for Removing Mercury from Coal-Fired Flue Gas

    SciTech Connect

    Jean Bustard; Charles Lindsey; Paul Brignac: Travis Starns; Sharon Sjostrom; Trent Taylor; Cindy Larson

    2005-04-28

    generating plant that is equipped with a COHPAC{reg_sign} system. The overall objective is to evaluate the long-term effects of sorbent injection on mercury capture and COHPAC{reg_sign} performance. The work is being done on one-half of the gas stream at Alabama Power Company's Plant Gaston Unit 3 (nominally 135 MW). Data from the testing will be used to determine: (1) If sorbent injection into a high air-to-cloth ratio baghouse is a viable, long-term approach for mercury control; and (2) Design criteria and costs for new baghouse/sorbent injection systems that will use a similar, polishing baghouse (TOXECON{trademark}) approach.

  15. Field Test Program for Long-Term Operation of a COHPAC System for Removing Mercury from Coal-Fired Flue Gas

    SciTech Connect

    Jean Bustard; Charles Lindsey; Paul Brignac; Travis Starns; Sharon Sjostrom; Cindy Larson

    2006-04-24

    generating plant that is equipped with a COHPAC{reg_sign} system. The overall objective is to evaluate the long-term effects of sorbent injection on mercury capture and COHPAC{reg_sign} performance. The work is being done on one-half of the gas stream at Alabama Power Company's Plant Gaston Unit 3 (nominally 135 MW). Data from the testing will be used to determine: (1) If sorbent injection into a high air-to-cloth ratio baghouse is a viable, long-term approach for mercury control; and (2) Design criteria and costs for new baghouse/sorbent injection systems that will use a similar, polishing baghouse (TOXECON{trademark}) approach.

  16. FIELD TEST PROGRAM FOR LONG-TERM OPERATION OF A COHPAC SYSTEM FOR REMOVING MERCURY FROM COAL-FIRED FLUE GAS

    SciTech Connect

    Jean Bustard; Charles Lindsey; Paul Brignac; Travis Starns; Sharon Sjostrom; Tom Millar

    2003-07-30

    overall objective is to evaluate the long-term effects of sorbent injection on mercury capture and COHPAC performance. The work is being done on one-half of the gas stream at Alabama Power Company's Plant Gaston Unit 3 (nominally 135 MW). Data from the testing will be used to determine: (1) If sorbent injection into a high air-to-cloth ratio baghouse is a viable, long-term approach for mercury control; and (2) Design criteria and costs for new baghouse/sorbent injection systems that will use a similar, polishing baghouse (TOXECON) approach.

  17. Field Test Program for Long-Term Operation of a COHPAC System for Removing Mercury from Coal-Fired Flue Gas

    SciTech Connect

    Jean Bustard; Charles Lindsey; Paul Brignac; Travis Starns; Sharon Sjostrom; Cindy Larson

    2005-10-24

    generating plant that is equipped with a COHPAC{reg_sign} system. The overall objective is to evaluate the long-term effects of sorbent injection on mercury capture and COHPAC{reg_sign} performance. The work is being done on one-half of the gas stream at Alabama Power Company's Plant Gaston Unit 3 (nominally 135 MW). Data from the testing will be used to determine: (1) If sorbent injection into a high air-to-cloth ratio baghouse is a viable, long-term approach for mercury control; and (2) Design criteria and costs for new baghouse/sorbent injection systems that will use a similar, polishing baghouse (TOXECON{trademark}) approach.

  18. Arapahoe low-sulfur-coal Fabric Filter Pilot Plant: Volume 4, Shake-deflate cleaning tests, May 1984--July 1986: Final report

    SciTech Connect

    Cushing, K.M.; Bustard, C.J.; Smith, W.B.

    1989-06-01

    This report describes operations at EPRI's low-sulfur coal Fabric Filter Pilot Plant during a twenty-seven month evaluation of shake-deflate cleaning. The primary objective was to collect sufficient data to optimize shake-deflate parameters and to allow prediction of baghouses operation with this cleaning method at utility power plants burning low-sulfur coal. The tests evaluated baghouse performance (pressure drop at various filtering air-to-cloth ratios, dustcake weight, and emissions) as a function of bag-cap acceleration, shake frequency, shake duration, and deflation volume. The findings indicate that shake-deflate cleaning can reduce cake weight and tube-sheet pressure drops by greater than 50% over conventional reverse-gas cleaned units. No bag life problems were observed over 11,000 h of testing, and emissions were very low (0.006 lb/10/sup 6/ Btu). Minimum filter pressure drop was attained at a bag-cap acceleration of 1.4 g (amplitude 2 in. and frequency 3 Hz). Low frequency high-amplitude shaking was more effective than high-frequency low-amplitude shaking. Shake durations around 20 s (at 3 Hz) preceded by deflation flows equivalent to about one-sixth total bag volume (1 ft/min deflation flow for 3 s) gave optimal performance. 9 refs., 12 figs., 5 tabs.

  19. Field Testing of Activated Carbon Injection Options for Mercury Control at TXU's Big Brown Station

    SciTech Connect

    John Pavlish; Jeffrey Thompson; Christopher Martin; Mark Musich; Lucinda Hamre

    2009-01-07

    time that enhanced AC was injected, the average mercury removal for the month long test was approximately 74% across the test baghouse module. ACI was interrupted frequently during the month long test because the test baghouse module was bypassed frequently to relieve differential pressure. The high air-to-cloth ratio of operations at this unit results in significant differential pressure, and thus there was little operating margin before encountering differential pressure limits, especially at high loads. This limited the use of sorbent injection as the added material contributes to the overall differential pressure. This finding limits sustainable injection of AC without appropriate modifications to the plant or its operations. Handling and storage issues were observed for the TOXECON ash-AC mixture. Malfunctioning equipment led to baghouse dust hopper plugging, and storage of the stagnant material at flue gas temperatures resulted in self-heating and ignition of the AC in the ash. In the hoppers that worked properly, no such problems were reported. Economics of mercury control at Big Brown were estimated for as-tested scenarios and scenarios incorporating changes to allow sustainable operation. This project was funded under the U.S. Department of Energy National Energy Technology Laboratory project entitled 'Large-Scale Mercury Control Technology Field Testing Program--Phase II'.

  20. ENVIRONMENTAL TECHNOLOGY VERIFICATION OF BAGHOUSE FILTRATION PRODUCTS

    EPA Science Inventory

    The Environmental Technology Verification Program (ETV) was started by EPA in 1995 to generate independent credible data on the performance of innovative technologies that have potential to improve protection of public health and the environment. ETV does not approve or certify p...

  1. Full-scale evaluation of mercury control with sorbent injection and COHPAC at Alabama Power E.C. Gaston.

    PubMed

    Bustard, C Jean; Durham, Michael; Lindsey, Charles; Starns, Travis; Baldrey, Ken; Martin, Cameron; Schlager, Richard; Sjostrom, Sharon; Slye, Rick; Renninger, Scott; Monroe, Larry; Miller, Richard; Chang, Ramsay

    2002-08-01

    The overall objective of this project was to determine the cost and impacts of Hg control using sorbent injection into a Compact Hybrid Particulate Collector (COHPAC) at Alabama Power's Gaston Unit 3. This test is part of a program funded by the U.S. Department of Energy's National Energy Technology Laboratory (NETL) to obtain the necessary information to assess the costs of controlling Hg from coal-fired utility plants that do not have scrubbers for SO2 control. The economics will be developed based on various levels of Hg control. Gaston Unit 3 was chosen for testing because COHPAC represents a cost-effective retrofit option for utilities with existing electrostatic precipitators (ESPs). COHPAC is an EPRI-patented concept that places a high air-to-cloth ratio baghouse downstream of an existing ESP to improve overall particulate collection efficiency. Activated carbons were injected upstream of COHPAC and downstream of the ESP to obtain performance and operational data. Results were very encouraging, with up to 90% removal of Hg for short operating periods using powdered activated carbon (PAC). During the long-term tests, an average Hg removal efficiency of 78% was measured. The PAC injection rate for the long-term tests was chosen to maintain COHPAC cleaning frequency at less than 1.5 pulses/bag/hr.

  2. The Golden Ratio

    ERIC Educational Resources Information Center

    Hyde, Hartley

    2004-01-01

    The Golden Ratio is sometimes called the "Golden Section" or the "Divine Proportion", in which three points: A, B, and C, divide a line in this proportion if AC/AB = AB/BC. "Donald in Mathmagicland" includes a section about the Golden Ratio and the ratios within a five-pointed star or pentagram. This article presents two computing exercises that…

  3. Offer/Acceptance Ratio.

    ERIC Educational Resources Information Center

    Collins, Mimi

    1997-01-01

    Explores how human resource professionals, with above average offer/acceptance ratios, streamline their recruitment efforts. Profiles company strategies with internships, internal promotion, cooperative education programs, and how to get candidates to accept offers. Also discusses how to use the offer/acceptance ratio as a measure of program…

  4. High Aspect Ratio Wrinkles

    NASA Astrophysics Data System (ADS)

    Chen, Yu-Cheng; Crosby, Alfred

    2015-03-01

    Buckling-induced surface undulations are widely found in living creatures, for instance, gut villi and the surface of flower petal cells. These undulations provide unique functionalities with their extremely high aspect ratios. For the synthetic systems, sinusoidal wrinkles that are induced by buckling a thin film attached on a soft substrate have been proposed to many applications. However, the impact of the synthetic wrinkles have been restricted by limited aspect ratios, ranging from 0 to 0.35. Within this range, wrinkle aspect ratio is known to increase with increasing compressive strain until a critical strain is reached, at which point wrinkles transition to localizations, such as folds or period doublings. Inspired by the living creatures, we propose that wrinkles can be stabilized in high aspect ratio by manipulating the strain energy in the substrate. We experimentally demonstrate this idea by forming a secondary crosslinking network in the wrinkled surface and successfully achieve aspect ratio as large as 0.8. This work not only provides insights for the mechanism of high aspect ratio structures seen in living creatures, but also demonstrates significant promise for future wrinkle-based applications.

  5. Ratio imaging instrumentation.

    PubMed

    Dunn, Kenneth; Maxfield, Frederick R

    2003-01-01

    Using ratio imaging to obtain quantitative information from microscope images is a powerful tool that has been used successfully in numerous studies. Although ratio imaging reduces the effects of many parameters that can interfere with accurate measurements, it is not a panacea. In designing a ratio imaging experiment, all of the potential problems discussed in this chapter must be considered. Undoubtedly, other problems that were not discussed can also interfere with accurate and meaningful measurements. Many of the problems discussed here were observed in the authors' laboratories. In our experience there are no standard routines or methods that can foresee every problem before it has been encountered. Good experimental design can minimize problems, but the investigator must continue to be alert. Progress in instrumentation continues to overcome some of the difficulties encountered in ratio imaging. CCD cameras with 12- to 14-bit pixel depth are being used more frequently, and several confocal microscope manufacturers are now also using 12-bit digitization. The dramatic increase in the use of confocal microscopes over the past decade is now causing microscope manufacturers to more critically evaluate the effect of axial chromatic aberration in objectives, and recent designs to minimize this problem are being implemented. Other developments such as the use of AOTFs to attenuate laser lines extend the applicability of ratio imaging. Ratio imaging is clearly applicable to a wide range of cell biological problems beyond its widespread use for measuring ion concentrations. Imaginative but careful use of this technique should continue to provide novel insights into the properties of cells.

  6. Digit ratio in birds.

    PubMed

    Lombardo, Michael P; Thorpe, Patrick A; Brown, Barbara M; Sian, Katie

    2008-12-01

    The Homeobox (Hox) genes direct the development of tetrapod digits. The expression of Hox genes may be influenced by endogenous sex steroids during development. Manning (Digit ratio. New Brunswick, NJ: Rutgers University Press, 2002) predicted that the ratio between the lengths of digits 2 (2D) and 4 (4D) should be sexually dimorphic because prenatal exposure to estrogens and androgens positively influence the lengths of 2D and 4D, respectively. We measured digits and other morphological traits of birds from three orders (Passeriformes, house sparrow, Passer domesticus; tree swallow, Tachycineta bicolor; Pscittaciformes, budgerigar, Melopsittacus undulates; Galliformes, chicken, Gallus domesticus) to test this prediction. None were sexually dimorphic for 2D:4D and there were no associations between 2D:4D and other sexually dimorphic traits. When we pooled data from all four species after we averaged right and left side digits from each individual and z-transformed the resulting digit ratios, we found that males had significantly larger 2D:4D than did females. Tetrapods appear to be sexually dimorphic for 2D:4D with 2D:4D larger in males as in some birds and reptiles and 2D:4D smaller in males as in some mammals. The differences between the reptile and mammal lineages in the directionality of 2D:4D may be related to the differences between them in chromosomal sex determination. We suggest that (a) natural selection for a perching foot in the first birds may have overridden the effects of hormones on the development of digit ratio in this group of vertebrates and (b) caution be used in making inferences about prenatal exposure to hormones and digit ratio in birds.

  7. Multi-ratio transmission

    SciTech Connect

    Polak, J.C.

    1987-07-14

    A preselected multi-ratio power transmission is described comprising: input means for transmitting drive forces; output means; first, second and third friction clutch means each selectively engageable with the input means for accepting drive forces. First input gear means drivingly connects with the first friction clutch means; second input gear means drivingly connects with the second friction clutch means; third input gear means drivingly connects with the third clutch means; first output gear means drivingly connects with the first input gear means; second output gear means drivingly connects with the first and second input gear means; third output means drivingly connects between the third input gear means and the output means; and one double-acting synchronizer clutch for selectively engaging the first output gear means with the output means and alternately the second output gear means with the output means. The first friction clutch means and the one double-acting synchronizer clutch cooperates during engagement to establish two forward drive ratios between the input and output means. The second friction clutch means and the one double-acting synchronizer clutch cooperates during engagement to establish two other forward drive ratios between the input and output means. The third friction clutch means is engageable to provide another forward drive ratio between the input means and the output means; and the one double-acting synchronizer clutch is relieved of transmitting drive forces during the engagement of the third friction clutch means and being manipulable for alternate connection with either the first output gear or the second output gear while the third friction clutch means is engaged.

  8. Peak power ratio generator

    DOEpatents

    Moyer, R.D.

    A peak power ratio generator is described for measuring, in combination with a conventional power meter, the peak power level of extremely narrow pulses in the gigahertz radio frequency bands. The present invention in a preferred embodiment utilizes a tunnel diode and a back diode combination in a detector circuit as the only high speed elements. The high speed tunnel diode provides a bistable signal and serves as a memory device of the input pulses for the remaining, slower components. A hybrid digital and analog loop maintains the peak power level of a reference channel at a known amount. Thus, by measuring the average power levels of the reference signal and the source signal, the peak power level of the source signal can be determined.

  9. Peak power ratio generator

    DOEpatents

    Moyer, Robert D.

    1985-01-01

    A peak power ratio generator is described for measuring, in combination with a conventional power meter, the peak power level of extremely narrow pulses in the gigahertz radio frequency bands. The present invention in a preferred embodiment utilizes a tunnel diode and a back diode combination in a detector circuit as the only high speed elements. The high speed tunnel diode provides a bistable signal and serves as a memory device of the input pulses for the remaining, slower components. A hybrid digital and analog loop maintains the peak power level of a reference channel at a known amount. Thus, by measuring the average power levels of the reference signal and the source signal, the peak power level of the source signal can be determined.

  10. High-Ratio Gear Train

    NASA Technical Reports Server (NTRS)

    Lefever, A. E.

    1982-01-01

    Proposed arrangement of two connected planetary differentials results in gear ratio many times that obtainable in conventional series gear assembly of comparable size. Ratios of several thousand would present no special problems. Selection of many different ratios is available with substantially similar gear diameters. Very high gear ratios would be obtained from small mechanism.

  11. Ratio estimation in SIMS analysis

    NASA Astrophysics Data System (ADS)

    Ogliore, R. C.; Huss, G. R.; Nagashima, K.

    2011-09-01

    The determination of an isotope ratio by secondary ion mass spectrometry (SIMS) traditionally involves averaging a number of ratios collected over the course of a measurement. We show that this method leads to an additive positive bias in the expectation value of the estimated ratio that is approximately equal to the true ratio divided by the counts of the denominator isotope of an individual ratio. This bias does not decrease as the number of ratios used in the average increases. By summing all counts in the numerator isotope, then dividing by the sum of counts in the denominator isotope, the estimated ratio is less biased: the bias is approximately equal to the ratio divided by the summed counts of the denominator isotope over the entire measurement. We propose a third ratio estimator (Beale's estimator) that can be used when the bias from the summed counts is unacceptably large for the hypothesis being tested. We derive expressions for the variance of these ratio estimators as well as the conditions under which they are normally distributed. Finally, we investigate a SIMS dataset showing the effects of ratio bias, and discuss proper ratio estimation for SIMS analysis.

  12. Lidar ratio and depolarization ratio for cirrus clouds.

    PubMed

    Chen, Wei-Nai; Chiang, Chih-Wei; Nee, Jan-Bai

    2002-10-20

    We report on studies of the lidar and the depolarization ratios for cirrus clouds. The optical depth and effective lidar ratio are derived from the transmission of clouds, which is determined by comparing the backscattering signals at the cloud base and cloud top. The lidar signals were fitted to a background atmospheric density profile outside the cloud region to warrant the linear response of the return signals with the scattering media. An average lidar ratio, 29 +/- 12 sr, has been found for all clouds measured in 1999 and 2000. The height and temperature dependences ofthe lidar ratio, the optical depth, and the depolarization ratio were investigated and compared with results of LITE and PROBE. Cirrus clouds detected near the tropopause are usually optically thin and mostly subvisual. Clouds with the largest optical depths were found near 12 km with a temperature of approximately -55 degrees C. The multiple-scattering effect is considered for clouds with high optical depths, and this effect lowers the lidar ratios compared with a single-scattering condition. Lidar ratios are in the 20-40 range for clouds at heights of 12.5-15 km and are smaller than approximately 30 in height above 15 km. Clouds are usually optically thin for temperatures below approximately -65 degrees C, and in this region the optical depth tends to decrease with height. The depolarization ratio is found to increase with a height at 11-15 km and smaller than 0.3 above 16 km. The variation in the depolarization ratio with the lidar ratio was also reported. The lidar and depolarization ratios were discussed in terms of the types of hexagonal ice crystals.

  13. Sex Ratio Elasticity Influences the Selection of Sex Ratio Strategy.

    PubMed

    Wang, Yaqiang; Wang, Ruiwu; Li, Yaotang; Sam Ma, Zhanshan

    2016-12-23

    There are three sex ratio strategies (SRS) in nature-male-biased sex ratio, female-biased sex ratio and, equal sex ratio. It was R. A. Fisher who first explained why most species in nature display a sex ratio of ½. Consequent SRS theories such as Hamilton's local mate competition (LMC) and Clark's local resource competition (LRC) separately explained the observed deviations from the seemingly universal 1:1 ratio. However, to the best of our knowledge, there is not yet a unified theory that accounts for the mechanisms of the three SRS. Here, we introduce the price elasticity theory in economics to define sex ratio elasticity (SRE), and present an analytical model that derives three SRSs based on the following assumption: simultaneously existing competitions for both resources A and resources B influence the level of SRE in both sexes differently. Consequently, it is the difference (between two sexes) in the level of their sex ratio elasticity that leads to three different SRS. Our analytical results demonstrate that the elasticity-based model not only reveals a highly plausible mechanism that explains the evolution of SRS in nature, but also offers a novel framework for unifying two major classical theories (i.e., LMC &LRC) in the field of SRS research.

  14. Sex Ratio Elasticity Influences the Selection of Sex Ratio Strategy

    PubMed Central

    Wang, Yaqiang; Wang, Ruiwu; Li, Yaotang; (Sam) Ma, Zhanshan

    2016-01-01

    There are three sex ratio strategies (SRS) in nature—male-biased sex ratio, female-biased sex ratio and, equal sex ratio. It was R. A. Fisher who first explained why most species in nature display a sex ratio of ½. Consequent SRS theories such as Hamilton’s local mate competition (LMC) and Clark’s local resource competition (LRC) separately explained the observed deviations from the seemingly universal 1:1 ratio. However, to the best of our knowledge, there is not yet a unified theory that accounts for the mechanisms of the three SRS. Here, we introduce the price elasticity theory in economics to define sex ratio elasticity (SRE), and present an analytical model that derives three SRSs based on the following assumption: simultaneously existing competitions for both resources A and resources B influence the level of SRE in both sexes differently. Consequently, it is the difference (between two sexes) in the level of their sex ratio elasticity that leads to three different SRS. Our analytical results demonstrate that the elasticity-based model not only reveals a highly plausible mechanism that explains the evolution of SRS in nature, but also offers a novel framework for unifying two major classical theories (i.e., LMC & LRC) in the field of SRS research. PMID:28009000

  15. Sex Ratio Elasticity Influences the Selection of Sex Ratio Strategy

    NASA Astrophysics Data System (ADS)

    Wang, Yaqiang; Wang, Ruiwu; Li, Yaotang; (Sam) Ma, Zhanshan

    2016-12-01

    There are three sex ratio strategies (SRS) in nature—male-biased sex ratio, female-biased sex ratio and, equal sex ratio. It was R. A. Fisher who first explained why most species in nature display a sex ratio of ½. Consequent SRS theories such as Hamilton’s local mate competition (LMC) and Clark’s local resource competition (LRC) separately explained the observed deviations from the seemingly universal 1:1 ratio. However, to the best of our knowledge, there is not yet a unified theory that accounts for the mechanisms of the three SRS. Here, we introduce the price elasticity theory in economics to define sex ratio elasticity (SRE), and present an analytical model that derives three SRSs based on the following assumption: simultaneously existing competitions for both resources A and resources B influence the level of SRE in both sexes differently. Consequently, it is the difference (between two sexes) in the level of their sex ratio elasticity that leads to three different SRS. Our analytical results demonstrate that the elasticity-based model not only reveals a highly plausible mechanism that explains the evolution of SRS in nature, but also offers a novel framework for unifying two major classical theories (i.e., LMC & LRC) in the field of SRS research.

  16. Software For Computing Image Ratios

    NASA Technical Reports Server (NTRS)

    Yates, Gigi L.

    1993-01-01

    RATIO_TOOL is interactive computer program for viewing and analyzing large sets of multispectral image data created by imaging spectrometer. Uses ratios between intensities in different spectral bands in order to spot significant areas of interest within multispectral image. Each image band viewed iteratively, or selected image band of set of data requested and displayed. When image ratios computed, result displayed as grayscale image. Written in C Language.

  17. Prevalence odds ratio versus prevalence ratio: choice comes with consequences.

    PubMed

    Tamhane, Ashutosh R; Westfall, Andrew O; Burkholder, Greer A; Cutter, Gary R

    2016-12-30

    Odds ratio, risk ratio, and prevalence ratio are some of the measures of association which are often reported in research studies quantifying the relationship between an independent variable and the outcome of interest. There has been much debate on the issue of which measure is appropriate to report depending on the study design. However, the literature on selecting a particular category of the outcome to be modeled and/or change in reference group for categorical independent variables and the effect on statistical significance, although known, is scantly discussed nor published with examples. In this article, we provide an example of a cross-sectional study wherein prevalence ratio was chosen over (Prevalence) odds ratio and demonstrate the analytic implications of the choice of category to be modeled and choice of reference level for independent variables. Copyright © 2016 John Wiley & Sons, Ltd.

  18. Air/fuel ratio controller

    SciTech Connect

    Schechter, M.M.; Simko, A.O.

    1980-12-23

    An internal combustion engine has a fuel injection pump and an air/fuel ratio controller. The controller has a lever that is connected to the pump lever. An aneroid moves the controller lever as a function of changes in intake manifold vacuum to maintain a constant air/fuel ratio to the mixture charge. A fuel enrichment linkage is provided that modifies the movement of the fuel flow control lever by the aneroid in response to changes in manifold gas temperature levels and exhaust gas recirculation to maintain the constant air/fuel ratio. A manual override is provided to obtain a richer air/fuel ratio for maximum acceleration.

  19. High ratio recirculating gas compressor

    DOEpatents

    Weinbrecht, John F.

    1989-01-01

    A high ratio positive displacement recirculating rotary compressor is disclosed. The compressor includes an integral heat exchanger and recirculation conduits for returning cooled, high pressure discharge gas to the compressor housing to reducing heating of the compressor and enable higher pressure ratios to be sustained. The compressor features a recirculation system which results in continuous and uninterrupted flow of recirculation gas to the compressor with no direct leakage to either the discharge port or the intake port of the compressor, resulting in a capability of higher sustained pressure ratios without overheating of the compressor.

  20. High ratio recirculating gas compressor

    DOEpatents

    Weinbrecht, J.F.

    1989-08-22

    A high ratio positive displacement recirculating rotary compressor is disclosed. The compressor includes an integral heat exchanger and recirculation conduits for returning cooled, high pressure discharge gas to the compressor housing to reducing heating of the compressor and enable higher pressure ratios to be sustained. The compressor features a recirculation system which results in continuous and uninterrupted flow of recirculation gas to the compressor with no direct leakage to either the discharge port or the intake port of the compressor, resulting in a capability of higher sustained pressure ratios without overheating of the compressor. 10 figs.

  1. ENVIRONMENTAL TECHNOLOGY VERIFICATION (ETV) PROGRAM; BAGHOUSE FILTRATION PRODUCTS

    EPA Science Inventory

    The U.S. Environmental Protection Agency (EPA) Environmental Technology Verification (ETV) Program evaluates the performance of innovative air, water, pollution prevention and monitoring technologies that have the potential to improve human health and the environment. This techno...

  2. Pressure Ratio to Thermal Environments

    NASA Technical Reports Server (NTRS)

    Lopez, Pedro; Wang, Winston

    2012-01-01

    A pressure ratio to thermal environments (PRatTlE.pl) program is a Perl language code that estimates heating at requested body point locations by scaling the heating at a reference location times a pressure ratio factor. The pressure ratio factor is the ratio of the local pressure at the reference point and the requested point from CFD (computational fluid dynamics) solutions. This innovation provides pressure ratio-based thermal environments in an automated and traceable method. Previously, the pressure ratio methodology was implemented via a Microsoft Excel spreadsheet and macro scripts. PRatTlE is able to calculate heating environments for 150 body points in less than two minutes. PRatTlE is coded in Perl programming language, is command-line-driven, and has been successfully executed on both the HP and Linux platforms. It supports multiple concurrent runs. PRatTlE contains error trapping and input file format verification, which allows clear visibility into the input data structure and intermediate calculations.

  3. Continually variable transmission having fixed ratio and variable ratio mechanisms

    SciTech Connect

    Moan, R.D

    1989-06-06

    This patent describes a transmission for producing a stepless, continually variable range of ratios of the speed of its output to its input comprising: a fluid coupling having an impeller adapted for connection to a power source and a turbine hydrodynamically connected to the impeller; as planetary gearset having a ring gear, a sun gear, a first set of planet pinions meshing with the sun gear, a second set of planet pinions meshing with the first set of pinions and with the ring gear, and a pinion carrier on which the first and second sets of pinions are rotatably supported; first drive means drivable connecting the turbine and the sun gear for producing a variable speed ratio therebetween having a range between an underdrive ratio and an overdrive ratio; second drive means drivably connecting the impeller and the ring gear for producing a fixed speed ratio therebetween; a first clutch means for drivably connecting and disconnecting the ring gear and the second drive means; and a second clutch means for drivably connecting and disconnecting the first drive means and the pinion carrier.

  4. A Ratio Explanation for Evolution.

    ERIC Educational Resources Information Center

    Riss, Pam Helfers

    1993-01-01

    Describes hands-on physical anthropology activities for teaching students about evolution. Using evidence found in hominid skulls, students conduct investigations that involve calculating ratios. Eight full-page photographs of skulls from the program Stones and Bones are included. (PR)

  5. Overconfidence, Incentives and Digit Ratio

    PubMed Central

    Neyse, Levent; Bosworth, Steven; Ring, Patrick; Schmidt, Ulrich

    2016-01-01

    This paper contributes to a better understanding of the biological underpinnings of overconfidence by analyzing performance predictions in the Cognitive Reflection Test with and without monetary incentives. In line with the existing literature we find that the participants are too optimistic about their performance on average; incentives lead to higher performance; and males score higher than females on this particular task. The novelty of this paper is an analysis of the relation between participants’ performance prediction accuracy and their second to fourth digit ratio. It has been reported that the digit ratio is a negatively correlated bio-marker of prenatal testosterone exposure. In the un-incentivized treatment, we find that males with low digit ratios, on average, are significantly more overconfident about their performance. In the incentivized treatment, however, we observe that males with low digit ratios, on average, are less overconfident about their performance. These effects are not observed in females. We discuss how these findings fit into the literature on testosterone and decision making and how they might help to explain seemingly opposing evidence. PMID:27039893

  6. Estimating diversity via frequency ratios.

    PubMed

    Willis, Amy; Bunge, John

    2015-12-01

    We wish to estimate the total number of classes in a population based on sample counts, especially in the presence of high latent diversity. Drawing on probability theory that characterizes distributions on the integers by ratios of consecutive probabilities, we construct a nonlinear regression model for the ratios of consecutive frequency counts. This allows us to predict the unobserved count and hence estimate the total diversity. We believe that this is the first approach to depart from the classical mixed Poisson model in this problem. Our method is geometrically intuitive and yields good fits to data with reasonable standard errors. It is especially well-suited to analyzing high diversity datasets derived from next-generation sequencing in microbial ecology. We demonstrate the method's performance in this context and via simulation, and we present a dataset for which our method outperforms all competitors.

  7. Models of ratio schedule performance.

    PubMed

    Bizo, L A; Killeen, P R

    1997-07-01

    Predictions of P. R. Killeen's (1994) mathematical principles of reinforcement were tested for responding on ratio reinforcement schedules. The type of response key, the number of sessions per condition, and first vs. second half of a session had negligible effects on responding. Longer reinforcer durations and larger grain types engendered more responding, affecting primarily the parameter alpha (specific activation). Key pecking was faster than treadle pressing, affecting primarily the parameter delta (response time). Longer intertrial intervals led to higher overall response rates and shorter postreinforcement pauses and higher running rates, and ruled out some competing explanations. The treadle data required a distinction between the energetic requirements and rate-limiting properties of extended responses. The theory was extended to predict pause durations and run rates on ratio schedules.

  8. Strange Baryon to Meson Ratio

    NASA Astrophysics Data System (ADS)

    Cuautle, Eleazar; Ayala, Alejandro

    2014-05-01

    We present a model to compute baryon and meson transverse momentum distributions, and their ratios, in relativistic heavy-ion collisions. The model allows to compute the probability to form colorless bound states of either two or three quarks as functions of the evolving density during the collision. The qualitative differences of the baryon to meson ratio for different collision energies and for different particle species can be associated to the different density dependent probabilities and to the combinatorial factors which in turn depend on whether the quarks forming the bound states are heavy or light. We compare to experimental data and show that we obtain a good description up to intermediate values of pt.

  9. Sex ratios in bumble bees

    PubMed Central

    Bourke, A. F. G.

    1997-01-01

    The median proportion of investment in females among 11 populations of seven bumble bee (Bombus) species was 0.32 (range 0.07 to 0.64). By contrast, two species of workerless social parasites in the related genus Psithyrus had female-biased sex allocation, the reasons for which remain unclear. Male-biased sex allocation in Bombus contradicts the predictions of Trivers and Hare's sex ratio model for the social Hymenoptera, which are that the population sex investment ratio should be 0.5 (1:1) under queen control and 0.75 (3:1 females:males) under worker control (assuming single, once-mated, outbred queens and non-reproductive workers). Male bias in Bombus does not appear to be either an artefact, or purely the result of symbiotic sex ratio distorters. According to modifications of the Trivers–Hare model, the level of worker male-production in Bombus is insufficient to account for observed levels of male bias. There is also no evidence that male bias arises from either local resource competition (related females compete for resources) or local mate enhancement (related males cooperate in securing mates). Bulmer presented models predicting sexual selection for protandry (males are produced before females) in annual social Hymenoptera and, as a consequence (given some parameter values), male-biased sex allocation. Bumble bees fit the assumptions of Bulmer's models and are protandrous. These models therefore represent the best current explanation for the bees' male-biased sex investment ratios. This conclusion suggests that the relative timing of the production of the sexes strongly influences sex allocation in the social Hymenoptera.

  10. Segregation Ratios in Alport's Syndrome

    PubMed Central

    MacNeill, Elizabeth; Shaw, Richard F.

    1973-01-01

    Pooled data of 35 pedigrees for Alport's syndrome were analysed. Affected to normal ratios among the offspring of heterozgyous fathers and mothers were tabulated. Offspring of heterozygous mothers were tabulated separately where the mother showed symptoms of the disease and where she was asymptomatic. Three current theories on the inheritance of Alport's syndrome are considered and discussed. Each theory fails to account fully for the known facts. A non-chromosomal agent has not yet been excluded for this intriguing disease. PMID:4697851

  11. Envera Variable Compression Ratio Engine

    SciTech Connect

    Charles Mendler

    2011-03-15

    Aggressive engine downsizing, variable compression ratio and use of the Atkinson cycle are being combined to improve fuel economy by up to 40 percent relative to port fuel injected gasoline engines, while maintaining full engine power. Approach Engine downsizing is viewed by US and foreign automobile manufacturers as one of the best options for improving fuel economy. While this strategy has already demonstrated a degree of success, downsizing and fuel economy gains are currently limited. With new variable compression ratio technology however, the degree of engine downsizing and fuel economy improvement can be greatly increased. A small variable compression ratio (VCR) engine has the potential to return significantly higher vehicle fuel economy while also providing high power. Affordability and potential for near term commercialization are key attributes of the Envera VCR engine. VCR Technology To meet torque and power requirements, a smaller engine needs to do more work per stroke. This is typically accomplished by boosting the incoming charge with either a turbo or supercharger so that more energy is present in the cylinder per stroke to do the work. With current production engines the degree of engine boosting (which correlates to downsizing) is limited by detonation (combustion knock) at high boost levels. Additionally, the turbo or supercharger needs to be responsive and efficient while providing the needed boost. VCR technology eliminates the limitation of engine knock at high load levels by reducing compression ratio to {approx}9:1 (or whatever level is appropriate) when high boost pressures are needed. By reducing the compression ratio during high load demand periods there is increased volume in the cylinder at top dead center (TDC) which allows more charge (or energy) to be present in the cylinder without increasing the peak pressure. Cylinder pressure is thus kept below the level at which the engine would begin to knock. When loads on the engine are low

  12. Using Ratio Analysis to Evaluate Financial Performance.

    ERIC Educational Resources Information Center

    Minter, John; And Others

    1982-01-01

    The ways in which ratio analysis can help in long-range planning, budgeting, and asset management to strengthen financial performance and help avoid financial difficulties are explained. Types of ratios considered include balance sheet ratios, net operating ratios, and contribution and demand ratios. (MSE)

  13. Low conversion ratio fuel studies.

    SciTech Connect

    Smith, M. A.

    2006-02-28

    Recent studies on TRU disposition in fast reactors indicated viable reactor performance for a sodium cooled low conversion ratio reactor design. Additional studies have been initiated to refine the earlier work and consider the feasibility of alternate fuel forms such as nitride and oxide fuel (rather than metal fuel). These alternate fuel forms may have significant impacts upon the burner design and the safety behavior. The work performed thus far has focused on compiling the necessary fuel form property information and refinement of the physics models. For this limited project, the burner design and performance using nitride fuel will be assessed.

  14. Variable ratio regenerative braking device

    DOEpatents

    Hoppie, Lyle O.

    1981-12-15

    Disclosed is a regenerative braking device (10) for an automotive vehicle. The device includes an energy storage assembly (12) having a plurality of rubber rollers (26, 28) mounted for rotation between an input shaft (36) and an output shaft (42), clutches (38, 46) and brakes (40, 48) associated with each shaft, and a continuously variable transmission (22) connectable to a vehicle drivetrain and to the input and output shafts by the respective clutches. The rubber rollers are torsionally stressed to accumulate energy from the vehicle when the input shaft is clutched to the transmission while the brake on the output shaft is applied, and are torsionally relaxed to deliver energy to the vehicle when the output shaft is clutched to the transmission while the brake on the input shaft is applied. The transmission ratio is varied to control the rate of energy accumulation and delivery for a given rotational speed of the vehicle drivetrain.

  15. Weather-Corrected Performance Ratio

    SciTech Connect

    Dierauf, T.; Growitz, A.; Kurtz, S.; Cruz, J. L. B.; Riley, E.; Hansen, C.

    2013-04-01

    Photovoltaic (PV) system performance depends on both the quality of the system and the weather. One simple way to communicate the system performance is to use the performance ratio (PR): the ratio of the electricity generated to the electricity that would have been generated if the plant consistently converted sunlight to electricity at the level expected from the DC nameplate rating. The annual system yield for flat-plate PV systems is estimated by the product of the annual insolation in the plane of the array, the nameplate rating of the system, and the PR, which provides an attractive way to estimate expected annual system yield. Unfortunately, the PR is, again, a function of both the PV system efficiency and the weather. If the PR is measured during the winter or during the summer, substantially different values may be obtained, making this metric insufficient to use as the basis for a performance guarantee when precise confidence intervals are required. This technical report defines a way to modify the PR calculation to neutralize biases that may be introduced by variations in the weather, while still reporting a PR that reflects the annual PR at that site given the project design and the project weather file. This resulting weather-corrected PR gives more consistent results throughout the year, enabling its use as a metric for performance guarantees while still retaining the familiarity this metric brings to the industry and the value of its use in predicting actual annual system yield. A testing protocol is also presented to illustrate the use of this new metric with the intent of providing a reference starting point for contractual content.

  16. Isokinetic Hamstrings: Quadriceps Ratios in Intercollegiate Athletes.

    ERIC Educational Resources Information Center

    Rosene, John M.; Fogarty, Tracey D.; Mahaffey, Brian L.

    2001-01-01

    Compared the differences in the concentric hamstrings to quadriceps (H:Q) ratio among athletes in different sports at three velocities. Measurement of H:Q ratio of both knees among male and female college athletes indicated that the H:Q ratio increased as velocity increased. No differences existed for the H:Q ratio for sport or side of body. (SM)

  17. A Librarian's Primer on Financial Ratios.

    ERIC Educational Resources Information Center

    Kerbel, Sandra Sandor

    1982-01-01

    Explains in simple terms the nature and function of a number of basic types of business and industrial financial ratios. An annotated list of five basic sources for ratios is included and a reference list and bibliography are attached. (JL)

  18. Evolutionarily stable sex ratios and mutation load.

    PubMed

    Hough, Josh; Immler, Simone; Barrett, Spencer C H; Otto, Sarah P

    2013-07-01

    Frequency-dependent selection should drive dioecious populations toward a 1:1 sex ratio, but biased sex ratios are widespread, especially among plants with sex chromosomes. Here, we develop population genetic models to investigate the relationships between evolutionarily stable sex ratios, haploid selection, and deleterious mutation load. We confirm that when haploid selection acts only on the relative fitness of X- and Y-bearing pollen and the sex ratio is controlled by the maternal genotype, seed sex ratios evolve toward 1:1. When we also consider haploid selection acting on deleterious mutations, however, we find that biased sex ratios can be stably maintained, reflecting a balance between the advantages of purging deleterious mutations via haploid selection, and the disadvantages of haploid selection on the sex ratio. Our results provide a plausible evolutionary explanation for biased sex ratios in dioecious plants, given the extensive gene expression that occurs across plant genomes at the haploid stage.

  19. Variable mixture ratio performance through nitrogen augmentation

    NASA Technical Reports Server (NTRS)

    Beichel, R.; Obrien, C. J.; Bair, E. K.

    1988-01-01

    High/variable mixture ratio O2/H2 candidate engine cycles are examined for earth-to-orbit vehicle application. Engine performance and power balance information are presented for the candidate cycles relative to chamber pressure, bulk density, and mixture ratio. Included in the cycle screening are concepts where a third fluid (liquid nitrogen) is used to achieve a variable mixture ratio over the trajectory from liftoff to earth orbit. The third fluid cycles offer a very low risk, fully reusable, low operation cost alternative to high/variable mixture ratio bipropellant cycles. Variable mixture ratio engines with extendible nozzle are slightly lower performing than a single mixture ratio engine (MR = 7:1) with extendible nozzle. Dual expander engines (MR = 7:1) have slightly better performance than the single mixture ratio engine. Dual fuel dual expander engines offer a 16 percent improvement over the single mixture ratio engine.

  20. Spray Gun With Constant Mixing Ratio

    NASA Technical Reports Server (NTRS)

    Simpson, William G.

    1987-01-01

    Conceptual mechanism mounted in handle of spray gun maintains constant ratio between volumetric flow rates in two channels leading to spray head. With mechanism, possible to keep flow ratio near 1:1 (or another desired ratio) over range of temperatures, orifice or channel sizes, or clogging conditions.

  1. Management Ratios 1. For Colleges & Universities.

    ERIC Educational Resources Information Center

    Minter, John, Ed.

    Ratios that enable colleges and universities to select other institutions for comparison are presented. The ratios and underlying data also enable colleges to rank order institutions and to calculate means, quartiles, and ranges for these groups. The data are based on FY 1983 U.S. Department of Education Statistics. The ratios summarize the…

  2. 7 CFR 400.162 - Qualification ratios.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 6 2013-01-01 2013-01-01 false Qualification ratios. 400.162 Section 400.162...; Regulations for the 1997 and Subsequent Reinsurance Years § 400.162 Qualification ratios. The sixteen qualification ratios include: (a) Eleven National Association of Insurance Commissioner's (NAIC's)...

  3. 12 CFR 567.8 - Leverage ratio.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 12 Banks and Banking 6 2012-01-01 2012-01-01 false Leverage ratio. 567.8 Section 567.8 Banks and... § 567.8 Leverage ratio. (a) The minimum leverage capital requirement for a savings association assigned a composite rating of 1, as defined in § 516.3 of this chapter, shall consist of a ratio of...

  4. 12 CFR 167.8 - Leverage ratio.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 12 Banks and Banking 1 2014-01-01 2014-01-01 false Leverage ratio. 167.8 Section 167.8 Banks and... § 167.8 Leverage ratio. (a) The minimum leverage capital requirement for a Federal savings association assigned a composite rating of 1, as defined in § 116.3 of this chapter, shall consist of a ratio of...

  5. 7 CFR 400.162 - Qualification ratios.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 6 2012-01-01 2012-01-01 false Qualification ratios. 400.162 Section 400.162...; Regulations for the 1997 and Subsequent Reinsurance Years § 400.162 Qualification ratios. The sixteen qualification ratios include: (a) Eleven National Association of Insurance Commissioner's (NAIC's)...

  6. 12 CFR 390.467 - Leverage ratio.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 12 Banks and Banking 5 2014-01-01 2014-01-01 false Leverage ratio. 390.467 Section 390.467 Banks... REGULATIONS TRANSFERRED FROM THE OFFICE OF THRIFT SUPERVISION Capital § 390.467 Leverage ratio. (a) The... defined in this subpart, shall consist of a ratio of core capital to adjusted total assets of 3...

  7. 7 CFR 400.162 - Qualification ratios.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 6 2014-01-01 2014-01-01 false Qualification ratios. 400.162 Section 400.162...; Regulations for the 1997 and Subsequent Reinsurance Years § 400.162 Qualification ratios. The sixteen qualification ratios include: (a) Eleven National Association of Insurance Commissioner's (NAIC's)...

  8. 12 CFR 390.467 - Leverage ratio.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 12 Banks and Banking 5 2012-01-01 2012-01-01 false Leverage ratio. 390.467 Section 390.467 Banks... REGULATIONS TRANSFERRED FROM THE OFFICE OF THRIFT SUPERVISION Capital § 390.467 Leverage ratio. (a) The... defined in this subpart, shall consist of a ratio of core capital to adjusted total assets of 3...

  9. 7 CFR 400.162 - Qualification ratios.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 6 2011-01-01 2011-01-01 false Qualification ratios. 400.162 Section 400.162...; Regulations for the 1997 and Subsequent Reinsurance Years § 400.162 Qualification ratios. The sixteen qualification ratios include: (a) Eleven National Association of Insurance Commissioner's (NAIC's)...

  10. 12 CFR 567.8 - Leverage ratio.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Leverage ratio. 567.8 Section 567.8 Banks and... § 567.8 Leverage ratio. (a) The minimum leverage capital requirement for a savings association assigned a composite rating of 1, as defined in § 516.3 of this chapter, shall consist of a ratio of...

  11. 12 CFR 390.467 - Leverage ratio.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 12 Banks and Banking 5 2013-01-01 2013-01-01 false Leverage ratio. 390.467 Section 390.467 Banks... REGULATIONS TRANSFERRED FROM THE OFFICE OF THRIFT SUPERVISION Capital § 390.467 Leverage ratio. (a) The... defined in this subpart, shall consist of a ratio of core capital to adjusted total assets of 3...

  12. 12 CFR 567.8 - Leverage ratio.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 12 Banks and Banking 5 2011-01-01 2011-01-01 false Leverage ratio. 567.8 Section 567.8 Banks and... § 567.8 Leverage ratio. (a) The minimum leverage capital requirement for a savings association assigned a composite rating of 1, as defined in § 516.3 of this chapter, shall consist of a ratio of...

  13. 12 CFR 167.8 - Leverage ratio.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 12 Banks and Banking 1 2013-01-01 2013-01-01 false Leverage ratio. 167.8 Section 167.8 Banks and... § 167.8 Leverage ratio. (a) The minimum leverage capital requirement for a Federal savings association assigned a composite rating of 1, as defined in § 116.3 of this chapter, shall consist of a ratio of...

  14. 12 CFR 167.8 - Leverage ratio.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 12 Banks and Banking 1 2012-01-01 2012-01-01 false Leverage ratio. 167.8 Section 167.8 Banks and... § 167.8 Leverage ratio. (a) The minimum leverage capital requirement for a Federal savings association assigned a composite rating of 1, as defined in § 116.3 of this chapter, shall consist of a ratio of...

  15. 12 CFR 567.8 - Leverage ratio.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 12 Banks and Banking 6 2013-01-01 2012-01-01 true Leverage ratio. 567.8 Section 567.8 Banks and... § 567.8 Leverage ratio. (a) The minimum leverage capital requirement for a savings association assigned a composite rating of 1, as defined in § 516.3 of this chapter, shall consist of a ratio of...

  16. 12 CFR 567.8 - Leverage ratio.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 12 Banks and Banking 6 2014-01-01 2012-01-01 true Leverage ratio. 567.8 Section 567.8 Banks and... § 567.8 Leverage ratio. (a) The minimum leverage capital requirement for a savings association assigned a composite rating of 1, as defined in § 516.3 of this chapter, shall consist of a ratio of...

  17. Spectral ratio method for measuring emissivity

    USGS Publications Warehouse

    Watson, K.

    1992-01-01

    The spectral ratio method is based on the concept that although the spectral radiances are very sensitive to small changes in temperature the ratios are not. Only an approximate estimate of temperature is required thus, for example, we can determine the emissivity ratio to an accuracy of 1% with a temperature estimate that is only accurate to 12.5 K. Selecting the maximum value of the channel brightness temperatures is an unbiased estimate. Laboratory and field spectral data are easily converted into spectral ratio plots. The ratio method is limited by system signal:noise and spectral band-width. The images can appear quite noisy because ratios enhance high frequencies and may require spatial filtering. Atmospheric effects tend to rescale the ratios and require using an atmospheric model or a calibration site. ?? 1992.

  18. Eccentric crank variable compression ratio mechanism

    SciTech Connect

    Lawrence, Keith Edward; Moser, William Elliott; Roozenboom, Stephan Donald; Knox, Kevin Jay

    2008-05-13

    A variable compression ratio mechanism for an internal combustion engine that has an engine block and a crankshaft is disclosed. The variable compression ratio mechanism has a plurality of eccentric disks configured to support the crankshaft. Each of the plurality of eccentric disks has at least one cylindrical portion annularly surrounded by the engine block. The variable compression ratio mechanism also has at least one actuator configured to rotate the plurality of eccentric disks.

  19. Effect of particle aspect ratio in magnetorheology

    NASA Astrophysics Data System (ADS)

    Morillas, Jose R.; Carreón-González, Elizabeth; de Vicente, Juan

    2015-12-01

    We investigate the influence of the aspect ratio of the dispersed particles in magnetorheology. Two systems are studied: conventional magnetorheological fluids prepared by dispersion of nickel nanowires, and inverse ferrofluids prepared by dispersion of glass fibers in a ferrofluid. In both cases the apparent yield stress is found to increase with aspect ratio in contradiction to available models in the literature. Experimental observations demonstrate that the particle volume fraction within the aggregates initially increases with increasing the aspect ratio of the dispersed particles. When the aspect ratio is further raised, a gel-like percolating structure forms inhibiting the formation of elongated clusters in the field direction.

  20. Force dynamics in fixed-ratio schedules.

    PubMed

    Pinkston, Jonathan W; McBee, Lindsey N

    2014-03-01

    Fixed-ratio schedules are widely used in behavioral research. Although fixed-ratio schedules often conjure up relationships to work and effort, little is known about effort-related measures in these schedules. Early research had shown that force and effort of operant behavior vary systematically during the execution of ratio schedules, and the goal of the present study was to revisit early research on force dynamics in fixed-ratio schedules. Four rats earned sucrose by pressing an isometric force transducer. Presses produced sucrose after ten or twenty responses. In general, the force of responses increased then decreased systematically across the ratio. The possibility that decreases in force during ratio execution was due to a trade-off with the differential reinforcement of short inter-response times (IRT) was investigated in an additional condition where sucrose was made available according to a tandem fixed-ratio 19 inter-response (IRT)> t schedule. The tandem IRT requirement did not eliminate decreasing trends in force across the ratio; unexpectedly, the tandem requirement did eliminate increases in force early in the ratio, which may reflect sequence-level organization operating in the control of force dynamics.

  1. Calculating Obscuration Ratios Of Contaminated Surfaces

    NASA Technical Reports Server (NTRS)

    Barengoltz, Jack B.

    1989-01-01

    Equations derived to estimate obscuration ratios of surfaces contaminated by particles. Ratio is fraction of surface area covered by particles. Useful as index of cleanliness in clean-room operations in manufacturing of semiconductor devices, magnetic recording media, optical devices, and pharmaceutical and biotechnological products.

  2. The effects of nurse to patient ratios.

    PubMed

    Patterson, Jennifer

    This article examines the literature on nurse to patient ratios to establish the impact on both patients and staff of understaffing on hospital wards. It discusses theories on ideal staff to patient ratios and the resource implications of these, and recommends a number of dynamic and innovative ways to allocate staff.

  3. Sex ratios in pheasant research and management

    USGS Publications Warehouse

    Dale, F.H.

    1952-01-01

    Sex ratios are of primary importance in interpretation of extensive studies of pheasant populations. They are necessary for converting crowing-cock indices to population estimates even where annual trends are to be studied in the same area. Reliability of population estimates from hunting season kill of pheasants suffers primarily from inability to estimate sex ratios accurately. Fall sex ratio is an index to production and where adult sex ratios are divergent can serve as a good check on production per hen. Age ratios of cocks cannot be interpreted directly as an index of productivity, even within the boundaries of one state, unless adult sex ratios are known. The relationship between observed and actual sex ratio varies significantly from season to season and according to the method of observation. In view of their importance in population studies and the lack of reliability of present methods, it is believed that intensive studies on techniques for obtaining sex ratios are a major need in pheasant research.

  4. CCSSM Challenge: Graphing Ratio and Proportion

    ERIC Educational Resources Information Center

    Kastberg, Signe E.; D'Ambrosio, Beatriz S.; Lynch-Davis, Kathleen; Mintos, Alexia; Krawczyk, Kathryn

    2013-01-01

    A renewed emphasis was placed on ratio and proportional reasoning in the middle grades in the Common Core State Standards for Mathematics (CCSSM). The expectation for students includes the ability to not only compute and then compare and interpret the results of computations in context but also interpret ratios and proportions as they are…

  5. How to use and interpret hormone ratios.

    PubMed

    Sollberger, Silja; Ehlert, Ulrike

    2016-01-01

    Hormone ratios have become increasingly popular throughout the neuroendocrine literature since they offer a straightforward way to simultaneously analyze the effects of two interdependent hormones. However, the analysis of ratios is associated with statistical and interpretational concerns which have not been sufficiently considered in the context of endocrine research. The aim of this article, therefore, is to demonstrate and discuss these issues, and to suggest suitable ways to address them. In a first step, we use exemplary testosterone and cortisol data to illustrate that one major concern of ratios lies in their distribution and inherent asymmetry. As a consequence, results of parametric statistical analyses are affected by the ultimately arbitrary decision of which way around the ratio is computed (i.e., A/B or B/A). We suggest the use of non-parametric methods as well as the log-transformation of hormone ratios as appropriate methods to deal with these statistical problems. However, in a second step, we also discuss the complicated interpretation of ratios, and propose moderation analysis as an alternative and oftentimes more insightful approach to ratio analysis. In conclusion, we suggest that researchers carefully consider which statistical approach is best suited to investigate reciprocal hormone effects. With regard to the hormone ratio method, further research is needed to specify what exactly this index reflects on the biological level and in which cases it is a meaningful variable to analyze.

  6. Manganese nodules: thorium-230: protactinium-231 ratios.

    PubMed

    Sackett, W M

    1966-11-04

    The Th(230): Pa(231) activity ratio in 7 of 11 manganese nodules is less than 10.8, the theoretical production ratio of activities in the ocean. This finding indicates difierential accumulation of these nuclides in authigenic deposits of manganese-iron oxide.

  7. Tower Water-Vapor Mixing Ratio

    SciTech Connect

    Guastad, Krista; Riihimaki, Laura; none,

    2013-04-01

    The purpose of the Tower Water-Vapor Mixing Ratio (TWRMR) value-added product (VAP) is to calculate water-vapor mixing ratio at the 25-meter and 60-meter levels of the meteorological tower at the Southern Great Plains (SGP) Central Facility.

  8. Negative Poisson's ratio in rippled graphene.

    PubMed

    Qin, Huasong; Sun, Yu; Liu, Jefferson Zhe; Li, Mengjie; Liu, Yilun

    2017-03-10

    In this work, we perform molecular dynamics (MD) simulations to study the effect of rippling on the Poisson's ratio of graphene. Due to the atomic scale thickness of graphene, out-of-plane ripples are generated in free standing graphene with topological defects (e.g. heptagons and pentagons) to release the in-plane deformation energy. Through MD simulations, we have found that the Poisson's ratio of rippled graphene decreases upon increasing its aspect ratio η (amplitude over wavelength). For the rippled graphene sheet η = 0.188, a negative Poisson's ratio of -0.38 is observed for a tensile strain up to 8%, while the Poisson's ratio for η = 0.066 is almost zero. During uniaxial tension, the ripples gradually become flat, thus the Poisson's ratio of rippled graphene is determined by the competing factors of the intrinsic positive Poisson's ratio of graphene and the negative Poisson's ratio due to the de-wrinkling effect. Besides, the rippled graphene exhibits excellent fracture strength and toughness. With the combination of its auxetic and excellent mechanical properties, rippled graphene may possess potential for application in nano-devices and nanomaterials.

  9. Osmosis and Surface Area to Volume Ratio.

    ERIC Educational Resources Information Center

    Barrett, D. R. B.

    1984-01-01

    Describes an experiment designed to help students understand the concepts of osmosis and surface area to volume ratio (SA:VOL). The task for students is to compare water uptake in different sizes of potato cubes and relate differences to their SA:VOL ratios. (JN)

  10. The Divine Ratio and Golden Rectangles.

    ERIC Educational Resources Information Center

    Cooper, Martin

    1982-01-01

    The material examines aspects of Fibonacci and Lucas sequences, the generation of the Divine Ratio, and the nature of this ratio in golden rectangles, triangles, and figures made up of golden triangles. It is noted Lucas sequence is formed like Fibonacci but has one and three as the first elements. (Author/MP)

  11. Human behaviour: sex ratio and the city.

    PubMed

    Székely, Áron; Székely, Tamás

    2012-09-11

    The ratio of males to females in a population is known to influence the behaviour, life histories and demography of animals. A recent experimental study finds that sex ratio also affects human economic behaviour, and in a manner consistent with evolutionary theory.

  12. Empirical Analysis of Drill Ratio Research

    ERIC Educational Resources Information Center

    Burns, M.K.

    2004-01-01

    Providing students an appropriate level of challenge, called the instructional level, is an important component of effective instruction. Research regarding the optimal ratio of known to unknown items for drill tasks has been inconsistent. The author of the current article conducted an empirical metaanalysis of research on drill ratios by using…

  13. High Transformer ratios in collinear wakefield accelerators.

    SciTech Connect

    Power, J. G.; Conde, M.; Yusof, Z.; Gai, W.; Jing, C.; Kanreykin, A.; Schoessow, P.; High Energy Physics; Euclid Techlabs, LLC

    2008-01-01

    Based on our previous experiment that successfully demonstrated wakefield transformer ratio enhancement in a 13.625 GHz dielectric-loaded collinear wakefield accelerator using the ramped bunch train technique, we present here a redesigned experimental scheme for even higher enhancement of the efficiency of this accelerator. Design of a collinear wakefield device with a transformer ratio R2, is presented. Using a ramped bunch train (RBT) rather than a single drive bunch, the enhanced transformer ratio (ETR) technique is able to increase the transformer ratio R above the ordinary limit of 2. To match the wavelength of the fundamental mode of the wakefield with the bunch length (sigmaz=2 mm) of the new Argonne wakefield accelerator (AWA) drive gun (where the experiment will be performed), a 26.625 GHz dielectric based accelerating structure is required. This transformer ratio enhancement technique based on our dielectric-loaded waveguide design will result in a compact, high efficiency accelerating structures for future wakefield accelerators.

  14. Duty ratio of cooperative molecular motors.

    PubMed

    Dharan, Nadiv; Farago, Oded

    2012-02-01

    Molecular motors are found throughout the cells of the human body and have many different and important roles. These micromachines move along filament tracks and have the ability to convert chemical energy into mechanical work that powers cellular motility. Different types of motors are characterized by different duty ratios, which is the fraction of time that a motor is attached to its filament. In the case of myosin II (a nonprocessive molecular machine with a low duty ratio), cooperativity between several motors is essential to induce motion along its actin filament track. In this work we use statistical mechanical tools to calculate the duty ratio of cooperative molecular motors. The model suggests that the effective duty ratio of nonprocessive motors that work in cooperation is lower than the duty ratio of the individual motors. The origin of this effect is the elastic tension that develops in the filament which is relieved when motors detach from the track.

  15. Scavenging ratios based on inflow air concentrations

    SciTech Connect

    Davis, W.E.; Dana, M.T.; Lee, R.N.; Slinn, W.G.N.; Thorp, J.M.

    1991-07-01

    Scavenging ratios were calculated from field measurements made during April 1985. Event precipitation samples were collected at the surface, but air chemistry measurements in the air mass feeding the precipitation were made from an aircraft. In contrast, ratios calculated in previous studies have used air concentration and precipitation chemistry data from only surface measurements. Average scavenging ratios were calculated for SO{sub 4}{sup 2{minus}}, NO{sub 3}{sup {minus}}, NH{sub 4}{sup +}, total sulfate, total nitrate, and total ammonium for 5 events; the geometric mean of these scavenging ratios were 8.5 {times} 10{sup 5}, 5.6 {times} 10{sup 6}, 4.3 {times} 10{sup 5}, 3.4 {times} 10{sup 5}, 2.4 {times} 10{sup 6}, and 9.7 {times} 10{sup 4}, respectively. These means are similar to but less variable than previous ratios formed using only surface data.

  16. Poisson's ratio of individual metal nanowires.

    PubMed

    McCarthy, Eoin K; Bellew, Allen T; Sader, John E; Boland, John J

    2014-07-07

    The measurement of Poisson's ratio of nanomaterials is extremely challenging. Here we report a lateral atomic force microscope experimental method to electromechanically measure the Poisson's ratio and gauge factor of individual nanowires. Under elastic loading conditions we monitor the four-point resistance of individual metallic nanowires as a function of strain and different levels of electrical stress. We determine the gauge factor of individual wires and directly measure the Poisson's ratio using a model that is independently validated for macroscopic wires. For macroscopic wires and nickel nanowires we find Poisson's ratios that closely correspond to bulk values, whereas for silver nanowires significant deviations from the bulk silver value are observed. Moreover, repeated measurements on individual silver nanowires at different levels of mechanical and electrical stress yield a small spread in Poisson ratio, with a range of mean values for different wires, all of which are distinct from the bulk value.

  17. Duty ratio of cooperative molecular motors

    NASA Astrophysics Data System (ADS)

    Dharan, Nadiv; Farago, Oded

    2012-02-01

    Molecular motors are found throughout the cells of the human body and have many different and important roles. These micromachines move along filament tracks and have the ability to convert chemical energy into mechanical work that powers cellular motility. Different types of motors are characterized by different duty ratios, which is the fraction of time that a motor is attached to its filament. In the case of myosin II (a nonprocessive molecular machine with a low duty ratio), cooperativity between several motors is essential to induce motion along its actin filament track. In this work we use statistical mechanical tools to calculate the duty ratio of cooperative molecular motors. The model suggests that the effective duty ratio of nonprocessive motors that work in cooperation is lower than the duty ratio of the individual motors. The origin of this effect is the elastic tension that develops in the filament which is relieved when motors detach from the track.

  18. Equity Theory Ratios as Causal Schemas

    PubMed Central

    Arvanitis, Alexios; Hantzi, Alexandra

    2016-01-01

    Equity theory approaches justice evaluations based on ratios of exchange inputs to exchange outcomes. Situations are evaluated as just if ratios are equal and unjust if unequal. We suggest that equity ratios serve a more fundamental cognitive function than the evaluation of justice. More particularly, we propose that they serve as causal schemas for exchange outcomes, that is, they assist in determining whether certain outcomes are caused by inputs of other people in the context of an exchange process. Equality or inequality of ratios in this sense points to an exchange process. Indeed, Study 1 shows that different exchange situations, such as disproportional or balanced proportional situations, create perceptions of give-and-take on the basis of equity ratios. Study 2 shows that perceptions of justice are based more on communicatively accepted rules of interaction than equity-based evaluations, thereby offering a distinction between an attribution and an evaluation cognitive process for exchange outcomes. PMID:27594846

  19. ADVANCED HYBRID PARTICULATE COLLECTOR - PILOT-SCALE TESTING

    SciTech Connect

    Ye Zhuang; Stanley J. Miller; Michael E. Collings; Michelle R. Olderbak

    2001-09-30

    A new concept in particulate control, called an advanced hybrid particulate collector (AHPC), is being developed at the Energy and Environmental Research Center (EERC) with U.S. Department of Energy (DOE) funding. In addition to DOE and the EERC, the project team includes W.L. Gore and Associates, Inc., Allied Environmental Technologies, Inc., and the Big Stone power station. The AHPC combines the best features of electrostatic precipitators (ESPs) and baghouses in a unique approach to develop a compact but highly efficient system. Filtration and electrostatics are employed in the same housing, providing major synergism between the two collection methods, both in the particulate collection step and in the transfer of dust to the hopper. The AHPC provides ultrahigh collection efficiency, overcoming the problem of excessive fine-particle emissions with conventional ESPs, and solves the problem of reentrainment and re-collection of dust in conventional baghouses. The objective of the AHPC is to provide >99.99% particulate collection efficiency for particle sizes from 0.01 to 50 {micro}m and be applicable for use with all U.S. coals at a lower cost than existing technologies. In previous field tests with the AHPC, some minor bag damage was observed that appeared to be caused by electrical effects. Extensive studies were then carried out to determine the reason for the bag damage and to find possible solutions without compromising AHPC performance. The best solution to prevent the bag damage was found to be perforated plates installed between the electrodes and the bags, which can block the electric field from the bag surface and intercept current to the bags. The perforated plates not only solve the bag damage problem, but also offer many other advantages such as operation at higher A/C (air-to-cloth) ratios, lower pressure drop, and an even more compact geometric arrangement. For this project, AHPC pilot-scale tests were carried out to understand the effect of the

  20. CALIPSO lidar ratio retrieval over the ocean.

    PubMed

    Josset, Damien; Rogers, Raymond; Pelon, Jacques; Hu, Yongxiang; Liu, Zhaoyan; Omar, Ali; Zhai, Peng-Wang

    2011-09-12

    We are demonstrating on a few cases the capability of CALIPSO to retrieve the 532 nm lidar ratio over the ocean when CloudSat surface scattering cross section is used as a constraint. We are presenting the algorithm used and comparisons with the column lidar ratio retrieved by the NASA airborne high spectral resolution lidar. For the three cases presented here, the agreement is fairly good. The average CALIPSO 532 nm column lidar ratio bias is 13.7% relative to HSRL, and the relative standard deviation is 13.6%. Considering the natural variability of aerosol microphysical properties, this level of accuracy is significant since the lidar ratio is a good indicator of aerosol types. We are discussing dependencies of the accuracy of retrieved aerosol lidar ratio on atmospheric aerosol homogeneity, lidar signal to noise ratio, and errors in the optical depth retrievals. We are obtaining the best result (bias 7% and standard deviation around 6%) for a nighttime case with a relatively constant lidar ratio (in the vertical) indicative of homogeneous aerosol type.

  1. Sex ratio in relation to fathers' occupations.

    PubMed Central

    Dickinson, H O; Parker, L

    1997-01-01

    OBJECTIVE: To investigate whether the sex ratio of children varies between fathers of different occupations. METHODS: The sex ratio (the ratio of the number of boys to the number of girls at birth) was calculated in relation to paternal occupation in the cohort of all 253,433 live births in Cumbria, north west England, from 1950-89. Exact binomial confidence intervals were used to estimate whether the sex ratio in each occupational category was significantly different from that for the rest of the cohort. RESULTS: There were fewer occupational categories with significantly different sex ratios at the 5% level than expected by chance alone, assuming the same binomial distribution of sexes at birth within each paternal occupation. CONCLUSIONS: Significant variation of the sex ratio with fathers' occupations was not found. There is some evidence that the sex ratio shows less variance than expected under a binomial model which assumes independence of the sex of each child; a possible explanation of this may be parental preference for limiting family size after children of both sexes have been born or some other factor which results in children within a family being more likely to be of both sexes rather than the same sex. PMID:9470894

  2. CALIPSO Lidar Ratio Retrieval Over the Ocean

    NASA Technical Reports Server (NTRS)

    Josset, Damien B.; Rogers, Raymond R.; Pelon, Jacques; Hu, Yongxiang; Liu, Zhaoyan; Omar, Ali H.; Zhai, Peng-Wang

    2011-01-01

    We are demonstrating on a few cases the capability of CALIPSO to retrieve the 532 nm lidar ratio over the ocean when CloudSat surface scattering cross section is used as a constraint. We are presenting the algorithm used and comparisons with the column lidar ratio retrieved by the NASA airborne high spectral resolution lidar. For the three cases presented here, the agreement is fairly good. The average CALIPSO 532 nm column lidar ratio bias is 13.7% relative to HSRL, and the relative standard deviation is 13.6%. Considering the natural variability of aerosol microphysical properties, this level of accuracy is significant since the lidar ratio is a good indicator of aerosol types. We are discussing dependencies of the accuracy of retrieved aerosol lidar ratio on atmospheric aerosol homogeneity, lidar signal to noise ratio, and errors in the optical depth retrievals. We are obtaining the best result (bias 7% and standard deviation around 6%) for a nighttime case with a relatively constant lidar ratio (in the vertical) indicative of homogeneous aerosol type

  3. Helium isotope ratios in Ethiopian Rift basalts

    NASA Astrophysics Data System (ADS)

    Scarsi, P.; Craig, H.

    1996-11-01

    Helium isotope ratios were measured in olivine and pyroxene phenocrysts from basalts of the Ethiopian Rift Valley and Afar Depression between 6° and 15°N and 37° and 43°E. 3He/4He ratios range from 6 to 17 times the atmospheric value (RA = 1.4 × 10-6), that is, from ratios less than typical MORB (depleted mantle) helium (R/RA= 8 ± 1) to ratios similar to high-3He hotspots and to the Yellowstone hotspot (R/RA= 16.5). The high 3He/4He ratios occur all along the Ethiopian Rift and well up into the Afar Depression, with a maximum value of 17.0 RA at 8°N in the Rift Axis and a high value of 14.2 RA in the central Tat'Ali sector of the Afar Depression. The ratios decrease to MORB-like values near the edge of the Red Sea, and to sub-MORB ratios (5-6 RA) at the northern end of the Rift (Zula Peninsula) and at the southern end, at lakes Abaya and Chamo. The Ethiopian Rift provides the only continental hotspot terrain in which helium isotope ratios can be compared in detail between volcanic lavas and associated geothermal and volcanic gases, a primary motivation for this work. Comparison with our previously measured ratios in fluids and gases (range 2-15 RA) shows excellent agreement in the areas sampled for both lavas and fluids, and indicates that high-temperature volcanic fluids can be used for establishing helium isotope signatures in such terrains. The high-3He values in both fluids and basalts show that a Primitive Mantle (PM) component is required and that a Lower Mantle High-3He plume is strongly involved as a driving force in the rifting process of the East African Rift System.

  4. Testing the ratio of two poisson rates.

    PubMed

    Gu, Kangxia; Ng, Hon Keung Tony; Tang, Man Lai; Schucany, William R

    2008-04-01

    In this paper we compare the properties of four different general approaches for testing the ratio of two Poisson rates. Asymptotically normal tests, tests based on approximate p -values, exact conditional tests, and a likelihood ratio test are considered. The properties and power performance of these tests are studied by a Monte Carlo simulation experiment. Sample size calculation formulae are given for each of the test procedures and their validities are studied. Some recommendations favoring the likelihood ratio and certain asymptotic tests are based on these simulation results. Finally, all of the test procedures are illustrated with two real life medical examples.

  5. Negative Poisson's ratio materials via isotropic interactions.

    PubMed

    Rechtsman, Mikael C; Stillinger, Frank H; Torquato, Salvatore

    2008-08-22

    We show that under tension a classical many-body system with only isotropic pair interactions in a crystalline state can, counterintuitively, have a negative Poisson's ratio, or auxetic behavior. We derive the conditions under which the triangular lattice in two dimensions and lattices with cubic symmetry in three dimensions exhibit a negative Poisson's ratio. In the former case, the simple Lennard-Jones potential can give rise to auxetic behavior. In the latter case, a negative Poisson's ratio can be exhibited even when the material is constrained to be elastically isotropic.

  6. Negative Poisson's Ratio in Modern Functional Materials.

    PubMed

    Huang, Chuanwei; Chen, Lang

    2016-10-01

    Materials with negative Poisson's ratio attract considerable attention due to their underlying intriguing physical properties and numerous promising applications, particularly in stringent environments such as aerospace and defense areas, because of their unconventional mechanical enhancements. Recent progress in materials with a negative Poisson's ratio are reviewed here, with the current state of research regarding both theory and experiment. The inter-relationship between the underlying structure and a negative Poisson's ratio is discussed in functional materials, including macroscopic bulk, low-dimensional nanoscale particles, films, sheets, or tubes. The coexistence and correlations with other negative indexes (such as negative compressibility and negative thermal expansion) are also addressed. Finally, open questions and future research opportunities are proposed for functional materials with negative Poisson's ratios.

  7. Doing Mathematics with Bicycle Gear Ratios.

    ERIC Educational Resources Information Center

    Stump, Sheryl L.

    2000-01-01

    Describes an activity in which students examine bicycle chain-rings, cogs, and gear ratios as a means of exploring algebraic relationships, data collection, scatter plots, and lines of best fit. (KHR)

  8. Three-dimensional stereo by photometric ratios

    SciTech Connect

    Wolff, L.B.; Angelopoulou, E.

    1994-11-01

    We present a methodology for corresponding a dense set of points on an object surface from photometric values for three-dimensional stereo computation of depth. The methodology utilizes multiple stereo pairs of images, with each stereo pair being taken of the identical scene but under different illumination. With just two stereo pairs of images taken under two different illumination conditions, a stereo pair of ratio images can be produced, one for the ratio of left-hand images and one for the ratio of right-hand images. We demonstrate how the photometric ratios composing these images can be used for accurate correspondence of object points. Object points having the same photometric ratio with respect to two different illumination conditions constitute a well-defined equivalence class of physical constraints defined by local surface orientation relative to illumination conditions. We formally show that for diffuse reflection the photometric ratio is invariant to varying camera characteristics, surface albedo, and viewpoint and that therefore the same photometric ratio in both images of a stereo pair implies the same equivalence class of physical constraints. The correspondence of photometric ratios along epipolar lines in a stereo pair of images under different illumination conditions is a correspondence of equivalent physical constraints, and the determination of depth from stereo can be performed. Whereas illumination planning is required, our photometric-based stereo methodology does not require knowledge of illumination conditions in the actual computation of three-dimensional depth and is applicable to perspective views. This technique extends the stereo determination of three-dimensional depth to smooth featureless surfaces without the use of precisely calibrated lighting. We demonstrate experimental depth maps from a dense set of points on smooth objects of known ground-truth shape, determined to within 1% depth accuracy.

  9. Approaches to high aspect ratio triangulations

    NASA Technical Reports Server (NTRS)

    Posenau, M.-A.

    1993-01-01

    In aerospace computational fluid dynamics calculations, high aspect ratio, or stretched, triangulations are necessary to adequately resolve the features of a viscous flow around bodies. In this paper, we explore alternatives to the Delaunay triangulation which can be used to generate high aspect ratio triangulations of point sets. The method is based on a variation of the lifting map concept which derives Delaunay triangulations from convex hull calculations.

  10. Plutonium isotope ratio variations in North America

    SciTech Connect

    Steiner, Robert E; La Mont, Stephen P; Eisele, William F; Fresquez, Philip R; Mc Naughton, Michael; Whicker, Jeffrey J

    2010-12-14

    Historically, approximately 12,000 TBq of plutonium was distributed throughout the global biosphere by thermo nuclear weapons testing. The resultant global plutonium fallout is a complex mixture whose {sup 240}Pu/{sup 239}Pu atom ratio is a function of the design and yield of the devices tested. The average {sup 240}Pu/{sup 239}Pu atom ratio in global fallout is 0.176 + 014. However, the {sup 240}Pu/{sup 239}Pu atom ratio at any location may differ significantly from 0.176. Plutonium has also been released by discharges and accidents associated with the commercial and weapons related nuclear industries. At many locations contributions from this plutonium significantly alters the {sup 240}Pu/{sup 239}Pu atom ratios from those observed in global fallout. We have measured the {sup 240}Pu/{sup 239}Pu atom ratios in environmental samples collected from many locations in North America. This presentation will summarize the analytical results from these measurements. Special emphasis will be placed on interpretation of the significance of the {sup 240}Pu/{sup 239}Pu atom ratios measured in environmental samples collected in the Arctic and in the western portions of the United States.

  11. Sex ratios at birth after induced abortion

    PubMed Central

    Urquia, Marcelo L.; Moineddin, Rahim; Jha, Prabhat; O’Campo, Patricia J.; McKenzie, Kwame; Glazier, Richard H.; Henry, David A.; Ray, Joel G.

    2016-01-01

    Background: Skewed male:female ratios at birth have been observed among certain immigrant groups. Data on abortion practices that might help to explain these findings are lacking. Methods: We examined 1 220 933 births to women with up to 3 consecutive singleton live births between 1993 and 2012 in Ontario. Records of live births, and induced and spontaneous abortions were linked to Canadian immigration records. We determined associations of male:female infant ratios with maternal birthplace, sex of the previous living sibling(s) and prior spontaneous or induced abortions. Results: Male:female infant ratios did not appreciably depart from the normal range among Canadian-born women and most women born outside of Canada, irrespective of the sex of previous children or the characteristics of prior abortions. However, among infants of women who immigrated from India and had previously given birth to 2 girls, the overall male:female ratio was 1.96 (95% confidence interval [CI] 1.75–2.21) for the third live birth. The male:female infant ratio after 2 girls was 1.77 (95% CI 1.26–2.47) times higher if the current birth was preceded by 1 induced abortion, 2.38 (95% CI 1.44–3.94) times higher if preceded by 2 or more induced abortions and 3.88 (95% CI 2.02–7.50) times higher if the induced abortion was performed at 15 weeks or more gestation relative to no preceding abortion. Spontaneous abortions were not associated with male-biased sex ratios in subsequent births. Interpretation: High male:female ratios observed among infants born to women who immigrated from India are associated with induced abortions, especially in the second trimester of pregnancy. PMID:27067818

  12. ADVANCED HYBRID PARTICULATE COLLECTOR

    SciTech Connect

    Ye Zhuang; Stanley J. Miller; Michelle R. Olderbak; Rich Gebert

    2001-12-01

    caused by electrical effects. Subsequently, extensive theoretical, bench-scale, and pilot-scale investigations were completed to find an approach to prevent bag damage without compromising AHPC performance. Results showed that the best bag protection and AHPC performance were achieved by using a perforated plate installed between the discharge electrodes and bags. This perforated-plate design was then installed in the 2.5-MW AHPC at Big Stone Power Plant in Big Stone City, South Dakota, and the AHPC was operated from March to June 2001. Results showed that the perforated-plate design solved the bag damage problem and offered even better AHPC performance than the previous design. All of the AHPC performance goals were met, including ultrahigh collection efficiency, high air-to-cloth ratio, reasonable pressure drop, and long bag-cleaning interval.

  13. Examining Earthquake Scaling Via Event Ratio Levels

    NASA Astrophysics Data System (ADS)

    Walter, W. R.; Yoo, S.; Mayeda, K. M.; Gok, R.

    2013-12-01

    A challenge with using corner frequency to interpret stress parameter scaling is that stress drop and apparent stress are related to the cube of the corner frequency. In practice this leads to high levels of uncertainty in measured stress from since the uncertainty in measuring the corner frequency is cubed to determine uncertainty in the stress parameters. We develop a new approach using the low and high frequency levels of spectral ratios between two closely located events recorded at the same stations. This approach has a number of advantages over more traditional corner frequency fitting, either in spectral ratios or individual spectra. First, if the bandwidth of the spectral ratio is sufficient, the levels can be measured at many individual frequency points and averaged, reducing the measurement error. Second the apparent stress (and stress drop) are related to the high frequency level to the 3/2 power so the measurement uncertainty is not as amplified as when using the corner frequency. Finally, if the bandwidth is sufficiently broad to determine both the spectral ratio low and high frequency levels, the apparent stress (or stress drop) ratio can be determined without the need to use any other measurements (e.g., moment, fault area), which of course have their own measurement uncertainties. We will show a number examples taken from a wide variety of crustal earthquake sequences. Example of the sigmoid formed by a spectral ratio between two hypothetical events for two different cases of stress scaling using the models described in this paper. Event 1 is Mw 6.0 event and event 2 is an Mw 4.0 event. In the self-similar case both have an apparent stress of 3 MPa, in the non-self-similar case the large event apparent stress is 3 MPA and the smaller one is 1 MPa. Note that ratio reaches different constant levels. The low frequency level (LVL) is the ratio of the moments and high frequency level (HFL) depends on the stress parameters. In this paper we derive the

  14. Autofluorescence ratio imaging of human colonic adenomas

    NASA Astrophysics Data System (ADS)

    Imaizumi, Katsuichi; Harada, Yoshinori; Wakabayashi, Naoki; Yamaoka, Yoshihisa; Dai, Ping; Tanaka, Hideo; Takamatsu, Tetsuro

    2011-02-01

    Recently autofluorescence imaging (AFI) endoscopy, visualizing tissue fluorescence in combination with reflected light, has been adopted as a technique for detecting neoplasms in the colon and other organs. However, autofluorescence colonoscopy is not infallible, and improvement of the detection method can be expected to enhance the performance. Colonic mucosa contains metabolism-related fluorophores, such as reduced nicotinamide adenine dinucleotide, which may be useful for visualizing neoplasia in autofluorescence endoscopy. We examined sliced cross-sections of endoscopically resected tubular adenomas under a microscope. Fluorescence images acquired at 365-nm excitation (F365ex) and 405-nm excitation (F405ex), and reflectance images acquired at 550 nm (R550) were obtained. Fluorescence ratio (F365ex/F405ex) images and reflectance/fluorescence ratio (R550/F405ex) images were calculated from the acquired images. The fluorescence ratio images could distinguish adenomatous mucosa from normal mucosa more clearly than the reflectance/fluorescence ratio images. The results showed that the autofluorescence ratio imaging is a potential technique for increasing the diagnostic power of autofluorescence endoscopy.

  15. Globin chain synthesis ratios in sideroblastic anaemia.

    PubMed

    Peters, R E; May, A; Jacobs, A

    1983-02-01

    Globin synthesis ratios were measured on reticulocytes from nine patients with primary acquired sideroblastic anaemia (SA), four patients with hereditary or congenital SA, two patients with secondary acquired SA and three patients with iron deficiency (ID). Ten of the samples from patients with SA and all the samples from patients with ID had normal ratios. Samples from three patients had significantly abnormal ratios, one from a patient with SA and acquired Hb H disease (alpha/beta 0 X 26), one from a patient with secondary acquired SA (alpha/beta 0 X 88), and one from a patient who went on to develop acute myeloblastic leukaemia (alpha/beta 1 X 36). Globin synthesis was stimulated by 100 microM haem similarly in normal, SA and ID reticulocytes. Any limitation of globin synthesis in SA and ID is therefore not easily reversible by adding haem. Inhibition of haem synthesis in nonsideroblastic reticulocytes using 4 mM isonicotinic acid hydrazide for 1 h incubation affected neither total globin synthesis nor the alpha/beta ratio. These results contradict the view that decreased haem synthesis decreases globin chain synthesis and decreases the alpha/beta globin chain synthesis ratios in human reticulocytes. Previously reported findings that haem could reverse globin chain synthesis inhibition in SA were good evidence for a primary deficiency of haem synthesis in the erythroblasts of these patients. Our inability to substantiate these findings emphasizes the need for a re-evaluation of the aetiology of sideroblastic anaemia.

  16. Isotope ratio determination in boron analysis.

    PubMed

    Sah, R N; Brown, P H

    1998-01-01

    Traditionally, boron (B) isotope ratios have been determined using thermal ionization mass spectrometry (TIMS) and, to some extent, secondary ion mass spectrometry (SIMS). Both TIMS and SIMS use a high-resolution mass analyzer, but differ in analyte ionization methods. TIMS uses electrons from a hot filament, whereas SIMS employs an energetic primary ion beam of Ga+, Cs+, or O- for analyte ionization. TIMS can be used in negative or positive ion modes with high sensitivity and precision of B isotope ratio determination. However, isobaric interferences may be a problem, if the sample is not well purified and/or memory of the previous sample is not removed. Time-consuming sample preparation, analyte (B) purification, and sample determination processes limit the applications of TIMS for routine analyses. SIMS can determine B and its isotope ratio in intact solid samples without destroying them, but has poorer resolution and sensitivity than TIMS, and is difficult to standardize for biological samples. Development of plasma-source mass spectrometry (MS) enabled the determination of B concentration and isotope ratio without requiring sample purification. Commonly used plasma-source MS uses an Ar inductively coupled plasma (ICP) as an ionization device interfaced to a low-resolution quadrupole mass analyzer. The quadrupole ICP-MS is less precise than TIMS and SIMS, but is a popular method for B isotope ratio determination because of its speed and convenience. B determination by ICP-MS suffers no spectroscopic interferences. However, sample matrices, memory effects, and some instrument parameters may affect the accuracy and precision of B isotope ratio determination if adequate precautions are not taken. New generations of plasma-source MS instruments using high-resolution mass analyzers provide better sensitivity and precision than the currently used quadrupole ICP-MS. Because of the convenience and high sample throughput, the high-resolution ICP-MS is expected to be the

  17. The D/H ratio for Jupiter

    NASA Astrophysics Data System (ADS)

    Smith, Wm. H.; Schempp, W. V.; Baines, K. H.

    1989-01-01

    Observations of Jupiter's spectrum near the R5(0) HD line at 6063.88 A are reported. A feature with an equivalent width of 0.065 + or - 0.021 mA is coincident with the expected line. This feature is compared with HD profiles computed for inhomogeneous scattering models for Jupiter to yield a range for the Jovian D/H ratio of 1.0-2.9 x 10 to the -5th. This D/H ratio is in the lower range of previously reported D/H values for Jupiter and corresponds to an essentially solar D/H ratio for Jupiter. The detection of HD features in the presence of probable blends with spectral features of minor atmospheric hydrocarbon molecules is discussed. Such blends may make unambiguous identification of HD features difficult.

  18. Is Canada's sex ratio in decline?

    PubMed Central

    Dodds, L; Armson, B A

    1997-01-01

    In this issue (see pages 37 to 41) Dr. Bruce B. Allan and associates report a small but statistically significant decrease--of about 0.2%--in the proportion of male live births in Canada over the period 1970-90. In this editorial, factors that have been reported in the literature to influence sex ratio are examined within a Canadian context. The authors suggest that although the reasons for the apparent decline in the sex ratio in Canada are unclear, the increasing use of ovulation induction may be a contributing factor. Data from the Nova Scotia Atlee Perinatal Database are discussed with a view to explaining the trend observed in Atlantic Canada, but no obvious explanation emerges. The authors argue that when the period of observation is extended no overall change in the sex ratio is apparent. This would suggest a tendency toward stabilization rather than decline. PMID:9006564

  19. Fixed-ratio escape reinforcement1

    PubMed Central

    Azrin, N. H.; Holz, W. C.; Hake, D. F.; Ayllon, T.

    1963-01-01

    Escape responses of squirrel monkeys were reinforced according to a fixed-ratio schedule. The reinforcement was a period of safety from a stimulus that signalled the delivery of intermittent pain-shocks. When the frequency of shock was gradually reduced, the performance remained at a high level until the shocks were quite infrequent. Similarly, the duration of the period of safety could be reduced to a few seconds with little loss of behavior. Thus, the responses appeared to be reinforced by even a brief period of safety, the actual degree of shock reduction being fairly slight. The changes in responding during this fixed-ratio escape procedure were comparable to the response changes typically obtained during fixed-ratio food procedures. PMID:13965780

  20. Magnetostrictive contribution to Poisson ratio of galfenol

    NASA Astrophysics Data System (ADS)

    Paes, V. Z. C.; Mosca, D. H.

    2013-09-01

    In this work we present a detailed study on the magnetostrictive contribution to Poisson ratio for samples under applied mechanical stress. Magnetic contributions to strain and Poisson ratio for cubic materials were derived by accounting elastic and magneto-elastic anisotropy contributions. We apply our theoretical results for a material of interest in magnetomechanics, namely, galfenol (Fe1-xGax). Our results show that there is a non-negligible magnetic contribution in the linear portion of the curve of stress versus strain. The rotation of the magnetization towards [110] crystallographic direction upon application of mechanical stress leads to an auxetic behavior, i.e., exhibiting Poisson ratio with negative values. This magnetic contribution to auxetic behavior provides a novel insight for the discussion of theoretical and experimental developments of materials that display unusual mechanical properties.

  1. A comparison of marginal odds ratio estimators.

    PubMed

    Loux, Travis M; Drake, Christiana; Smith-Gagen, Julie

    2017-02-01

    Uses of the propensity score to obtain estimates of causal effect have been investigated thoroughly under assumptions of linearity and additivity of exposure effect. When the outcome variable is binary relationships such as collapsibility, valid for the linear model, do not always hold. This article examines uses of the propensity score when both exposure and outcome are binary variables and the parameter of interest is the marginal odds ratio. We review stratification and matching by the propensity score when calculating the Mantel-Haenszel estimator and show that it is consistent for neither the marginal nor conditional odds ratio. We also investigate a marginal odds ratio estimator based on doubly robust estimators and summarize its performance relative to other recently proposed estimators under various conditions, including low exposure prevalence and model misspecification. Finally, we apply all estimators to a case study estimating the effect of Medicare plan type on the quality of care received by African-American breast cancer patients.

  2. Kinship Institutions and Sex Ratios in India

    PubMed Central

    CHAKRABORTY, TANIKA; KIM, SUKKOO

    2010-01-01

    This article explores the relationship between kinship institutions and sex ratios in India at the turn of the twentieth century. Because kinship rules vary by caste, language, religion, and region, we construct sex ratios by these categories at the district level by using data from the 1901 Census of India for Punjab (North), Bengal (East), and Madras (South). We find that the male-to-female sex ratio varied positively with caste rank, fell as one moved from the North to the East and then to the South, was higher for Hindus than for Muslims, and was higher for northern Indo-Aryan speakers than for the southern Dravidian-speaking people. We argue that these systematic patterns in the data are consistent with variations in the institution of family, kinship, and inheritance. PMID:21308567

  3. Differentiating Malignant from Tubercular Pleural Effusion by Cancer Ratio Plus (Cancer Ratio: Pleural Lymphocyte Count)

    PubMed Central

    Dagaonkar, Rucha S.; Marshall, Dominic; Abisheganaden, John; Light, R. W.

    2016-01-01

    Background. We performed prospective validation of the cancer ratio (serum LDH : pleural ADA ratio), previously reported as predictive of malignant effusion retrospectively, and assessed the effect of combining it with “pleural lymphocyte count” in diagnosing malignant pleural effusion (MPE). Methods. Prospective cohort study of patients hospitalized with lymphocyte predominant exudative pleural effusion in 2015. Results. 118 patients, 84 (71.2%) having MPE and 34 (28.8%) having tuberculous pleural effusion (TPE), were analysed. In multivariate logistic regression analysis, cancer ratio, serum LDH : pleural fluid lymphocyte count ratio, and “cancer ratio plus” (ratio of cancer ratio and pleural fluid lymphocyte count) correlated positively with MPE. The sensitivity and specificity of cancer ratio, ratio of serum LDH : pleural fluid lymphocyte count, and “cancer ratio plus” were 0.95 (95% CI 0.87–0.98) and 0.85 (95% CI 0.68–0.94), 0.63 (95% CI 0.51–0.73) and 0.85 (95% CI 0.68–0.94), and 97.6 (95% CI 0.90–0.99) and 94.1 (95% CI 0.78–0.98) at the cut-off level of >20, >800, and >30, respectively. Conclusion. Without incurring any additional cost, or requiring additional test, effort, or time, cancer ratio maintained and “cancer ratio plus” improved the specificity of cancer ratio in identifying MPE in the prospective cohort. PMID:28070157

  4. The mass ratio in spectroscopic binaries

    NASA Astrophysics Data System (ADS)

    Ducati, J. R.; Penteado, E. M.; Turcati, R.

    2003-08-01

    The process of formation of binary and multiple stars is not yet fully understood. Possibilities range from simultaneous processes of condensation from the primeval nebula, to isolated star formation and eventual capture to form a double system. Models exist that predict success probabilities for each theoretical process, and comparison with observational data is crucial. Spectroscopic binaries are specially suited to be used as observational data, since several biases that can arise from general catalogues of binary stars can be avoided, including dominance of systems with large separations between components. A very important parameter in these studies is the mass ratio, the quocient of the masses of primary and secundary members. The histogram of mass ratios provides crucial information to models of binary formation, linked to condensation processes and evolutionaty rates.In this case, spectroscopic binaries can be chosen as the observational sample, provided that the spectrum of the primary is from a non-evolved, main-sequence star,whose mass can be derived reliably from its spectral type. Defining an adequate limiting magnitude (6.5), one avoids bias from eclipsing systems with high inclinations, since nearly all systems up to 6.5 mag were detected. In this paper, a critical review is presented of the existing methods for deriving the distribution of the mass ratios from spectroscopic binary orbital data. After showing the incorrectness of some results published in the litterature, the available data (Batten's 8th Catalogue, 1989) is discussed. Simulations for several distributions of mass ratios (constant, quadratic, etc) are performed. It is shown that the existing data permits only to assert that the spectroscopic binaries with small mass ratios (q < 0.4) are more frequent that those with large mass ratios (q = 0.9 to 1.0).

  5. Radioactive anomaly discrimination from spectral ratios

    DOEpatents

    Maniscalco, James; Sjoden, Glenn; Chapman, Mac Clements

    2013-08-20

    A method for discriminating a radioactive anomaly from naturally occurring radioactive materials includes detecting a first number of gamma photons having energies in a first range of energy values within a predetermined period of time and detecting a second number of gamma photons having energies in a second range of energy values within the predetermined period of time. The method further includes determining, in a controller, a ratio of the first number of gamma photons having energies in the first range and the second number of gamma photons having energies in the second range, and determining that a radioactive anomaly is present when the ratio exceeds a threshold value.

  6. Secular trends in newborn sex ratios.

    PubMed

    Grech, Victor

    2014-11-01

    A wide variety of factors have been shown to influence the male to female ratio at birth, which invariably displays a male excess. This paper will review and amplify recent work by the author, with specific references to individual countries, regions and entire continents in order to provide a global overview of this subject. It will be shown that stress, including stress related to political events, influences this ratio. Man-made radiation is also shown to have played a significant role in relation to the Windscale fire (1957) and Chernobyl (1986).

  7. On the variability of alligator sex ratios

    USGS Publications Warehouse

    Nichols, J.D.; Chabreck, R.H.

    1980-01-01

    Samples of alligators from wild and 'farm' populations exhibited disproportionate sex ratios. Males predominated among young alligators from wild populations, whereas females were much more abundant than males in the farm population, where resources were superabundant. These results and other considerations lead us to hypothesize that environmental factors influence sex determination in alligators. During favorable environmental conditions natural selection is expected to favor a preponderance of the sex whose individuals exhibit the greater environmentally associated variation in relative fitness. We hypothesize that environmentally associated variation in age at sexual maturity of females produces sufficient variation in relative fitness of females to result in selection for low sex ratios during periods of resource abundance.

  8. Controlling Gas-Flow Mass Ratios

    NASA Technical Reports Server (NTRS)

    Morris, Brian G.

    1990-01-01

    Proposed system automatically controls proportions of gases flowing in supply lines. Conceived for control of oxidizer-to-fuel ratio in new gaseous-propellant rocket engines. Gas-flow control system measures temperatures and pressures at various points. From data, calculates control voltages for electronic pressure regulators for oxygen and hydrogen. System includes commercially available components. Applicable to control of mass ratios in such gaseous industrial processes as chemical-vapor depostion of semiconductor materials and in automotive engines operating on compressed natural gas.

  9. On virial analysis at low aspect ratio

    DOE PAGES

    Bongard, Michael W.; Barr, Jayson L.; Fonck, Raymond J.; ...

    2016-07-28

    The validity of virial analysis to infer global MHD equilibrium poloidal beta βp and internal inductance ℓi from external magnetics measurements is examined for low aspect ratio configurations with A < 2. Numerical equilibrium studies at varied aspect ratio are utilized to validate the technique at finite aspect ratio. The effect of applying high-A approximations to low-A experimental data is quantified and demonstrates significant over-estimation of stored energy (factors of 2–10) in spherical tokamak geometry. Experimental approximations to equilibrium-dependent volume integral terms in the analysis are evaluated at low-A. Highly paramagnetic configurations are found to be inadequately represented through themore » virial mean radius parameter RT. Alternate formulations for inferring βp and ℓi that are independent of RT to avoid this difficulty are presented for the static isotropic limit. Lastly, these formulations are suitable for fast estimation of tokamak stored energy components at low aspect ratio using virial analysis.« less

  10. Measuring Isotope Ratios Across the Solar System

    NASA Technical Reports Server (NTRS)

    Webster, Chris R.; Mahaffy, Paul R.

    2012-01-01

    Stable isotope ratios in C, H, N, O and S are powerful indicators of a wide variety of planetary geophysical processes that can identify origin, transport, temperature history, radiation exposure, atmospheric escape, environmental habitability and biology [1]. For the Allan Hills 84001 meteorite, for example, the (sup 1)(sup 3)C/(sup 1)(sup 2)C ratio identifies it as a Mars (SNC) meteorite; the ??K/??Ar ratio tells us the last time the rock cooled to solid, namely 4 Gya; isotope ratios in (sup 3)He, (sup 2)(sup 1)Ne and (sup 3)?Ar show it was in space (cosmic ray exposure) for 10-20 million years; (sup 1)?C dating that it sat in Antarctica for 13,000 years before discovery; and clumped isotope analysis of (sup 1)?O(sup 1)(sup 3)C(sup 1)?O in its carbonate that it was formed at 18+/-4 ?C in a near-surface aqueous environment [2]. Solar System Formation

  11. Measuring Poisson Ratios at Low Temperatures

    NASA Technical Reports Server (NTRS)

    Boozon, R. S.; Shepic, J. A.

    1987-01-01

    Simple extensometer ring measures bulges of specimens in compression. New method of measuring Poisson's ratio used on brittle ceramic materials at cryogenic temperatures. Extensometer ring encircles cylindrical specimen. Four strain gauges connected in fully active Wheatstone bridge self-temperature-compensating. Used at temperatures as low as liquid helium.

  12. Thin solar concentrator with high concentration ratio

    NASA Astrophysics Data System (ADS)

    Lin, Jhe-Syuan; Liang, Chao-Wen

    2013-09-01

    Solar concentrators are often used in conjunction with III-V multi-junction solar cells for cost reduction and efficiency improvement purposes. High flux concentration ratio, high optical efficiency and high manufacture tolerance are the key features required for a successful solar concentrator design. This paper describes a novel solar concentrator that combines the concepts, and thus the advantages, of both the refractive type ad reflective type. The proposed concentrator design adopts the Etendue-cascading concept that allows the light beams from all the concentric annular entrance pupils to be collected and transferred to the solar cell with minimal loss. This concept enables the system to perform near its Etendue-Limit and have a high concentration ratio simultaneously. Thereby reducing the costs of solar cells and therefor achieves a better the per watts cost. The concentrator demonstrated has a thing aspect ratio of 0.19 with a zero back focal distance. The numerical aperture at the solar cell immersed inside the dielectric concentrator is as high as 1.33 achieving a unprecedented high optical concentration ratio design.

  13. Male pygmy hippopotamus influence offspring sex ratio

    PubMed Central

    Saragusty, Joseph; Hermes, Robert; Hofer, Heribert; Bouts, Tim; Göritz, Frank; Hildebrandt, Thomas B.

    2012-01-01

    Pre-determining fetal sex is against the random and equal opportunity that both conceptus sexes have by nature. Yet, under a wide variety of circumstances, populations shift their birth sex ratio from the expected unity. Here we show, using fluorescence in situ hybridization, that in a population of pygmy hippopotamus (Choeropsis liberiensis) with 42.5% male offspring, males bias the ratio of X- and Y-chromosome-bearing spermatozoa in their ejaculates, resulting in a 0.4337±0.0094 (mean±s.d.) proportion of Y-chromosome-bearing spermatozoa. Three alternative hypotheses for the shifted population sex ratio were compared: female counteract male, female indifferent, or male and female in agreement. We conclude that there appears little or no antagonistic sexual conflict, unexpected by prevailing theories. Our results indicate that males possess a mechanism to adjust the ratio of X- and Y-chromosome-bearing spermatozoa in the ejaculate, thereby substantially expanding currently known male options in sexual conflict. PMID:22426218

  14. Giving More Realistic Definitions of Trigonometric Ratios

    ERIC Educational Resources Information Center

    Bhattacharjee, Pramode Ranjan

    2012-01-01

    Trigonometry is a well known branch of Mathematics. The study of trigonometry is of great importance in surveying, astronomy, navigation, engineering, and in different branches of science. This paper reports on the discovery of flaws in the traditional definitions of trigonometric ratios of an angle, which (in most cases) make use of the most…

  15. New definitions for cotton fiber maturity ratio

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Cotton fiber maturity affects fiber physical, mechanical, and chemical properties, as well as the processability and qualities of yarn and fabrics. New definitions of cotton fiber maturity ratio are introduced. The influences of sampling, sample preparation, measurement method, and correlations am...

  16. Interview Design for Ratio Comparison Tasks

    ERIC Educational Resources Information Center

    Alatorre, Silvia; Figueras, Olimpia

    2003-01-01

    In this article, which is part of an ongoing research, a classification is proposed for ratio comparison problems, according to their context, their quantity type, and their numerical structure. Deriving from this classification, an interview protocol was designed, and guidelines for the interpretation of answers into strategies were decided. A…

  17. Automated Signal-to-Noise Ratio Measurement

    NASA Technical Reports Server (NTRS)

    Pineda, J. E.

    1986-01-01

    Computer-controlled spectrum analysis gives rapid results for communication systems. Locates carrier signal in intermediate-frequency band and measures both carrier amplitude and amplitude of noise in several channels near carrier frequency. Computer then computes ratio of signal to average noise. Because measurements and calculations are rapid, system used in fading communication channels.

  18. Delayed reinforcement and fixed-ratio performance.

    PubMed

    Jarmolowicz, David P; Lattal, Kennon A

    2013-11-01

    Effects of delayed reinforcement on fixed-ratio (FR) maintained responding of pigeons were investigated. In Experiments 1-3, the delay of reinforcement was increased across successive sessions until pigeons paused for 300 s. Both signaled and unsignaled delays were studied across different conditions. Overall response rates and run rates (timed from the first to last response of a ratio) decreased and postreinforcement pauses increased as delays increased in each experiment. As delays increased, the likelihood of pausing during a ratio run also increased. When these measures were plotted as a function of obtained delays, signaled delays had less of an effect on the above measures than did unsignaled ones. In Experiment 2, delays had a greater effect on the above measures than did a control condition arranging equivalent interreinforcer intervals to those accompanying the delays. Experiments 3 and 4 examined the generality of the effects obtained in the first two experiments. In Experiment 3, delays imposed on FR or yoked-interval schedules had similar behavioral effects. In Experiment 4, effects similar to those found in Experiments 1-3 for 1, 10, and 20-s delays imposed on FR 50 schedules were found when the FR requirement increased across sessions. Despite the different contingencies relating response rate and reinforcement rates on interval and ratio schedules, delays of reinforcement generally affect performance on these schedules similarly.

  19. Convergence of m-bonacci 'golden ratios'

    NASA Astrophysics Data System (ADS)

    Ahrens, K.; Brown, D. A.; Kramer, A.

    2014-05-01

    This paper proves that the ratios of consecutive terms of the m-bonacci sequence converge to a limit φm < 2 and, as m → ∞, these φm converge to 2. Further, it is shown that the generating functions for the m-bonacci sequences converge pointwise to the geometric series.

  20. Male pygmy hippopotamus influence offspring sex ratio.

    PubMed

    Saragusty, Joseph; Hermes, Robert; Hofer, Heribert; Bouts, Tim; Göritz, Frank; Hildebrandt, Thomas B

    2012-02-28

    Pre-determining fetal sex is against the random and equal opportunity that both conceptus sexes have by nature. Yet, under a wide variety of circumstances, populations shift their birth sex ratio from the expected unity. Here we show, using fluorescence in situ hybridization, that in a population of pygmy hippopotamus (Choeropsis liberiensis) with 42.5% male offspring, males bias the ratio of X- and Y-chromosome-bearing spermatozoa in their ejaculates, resulting in a 0.4337±0.0094 (mean±s.d.) proportion of Y-chromosome-bearing spermatozoa. Three alternative hypotheses for the shifted population sex ratio were compared: female counteract male, female indifferent, or male and female in agreement. We conclude that there appears little or no antagonistic sexual conflict, unexpected by prevailing theories. Our results indicate that males possess a mechanism to adjust the ratio of X- and Y-chromosome-bearing spermatozoa in the ejaculate, thereby substantially expanding currently known male options in sexual conflict.

  1. On virial analysis at low aspect ratio

    SciTech Connect

    Bongard, Michael W.; Barr, Jayson L.; Fonck, Raymond J.; Reusch, Joshua A.; Thome, Kathreen E.

    2016-07-28

    The validity of virial analysis to infer global MHD equilibrium poloidal beta βp and internal inductance ℓi from external magnetics measurements is examined for low aspect ratio configurations with A < 2. Numerical equilibrium studies at varied aspect ratio are utilized to validate the technique at finite aspect ratio. The effect of applying high-A approximations to low-A experimental data is quantified and demonstrates significant over-estimation of stored energy (factors of 2–10) in spherical tokamak geometry. Experimental approximations to equilibrium-dependent volume integral terms in the analysis are evaluated at low-A. Highly paramagnetic configurations are found to be inadequately represented through the virial mean radius parameter RT. Alternate formulations for inferring βp and ℓi that are independent of RT to avoid this difficulty are presented for the static isotropic limit. Lastly, these formulations are suitable for fast estimation of tokamak stored energy components at low aspect ratio using virial analysis.

  2. Compression ratio effect on methane HCCI combustion

    SciTech Connect

    Aceves, S. M.; Pitz, W.; Smith, J. R.; Westbrook, C.

    1998-09-29

    We have used the HCT (Hydrodynamics, Chemistry and Transport) chemical kinetics code to simulate HCCI (homogeneous charge compression ignition) combustion of methane-air mixtures. HCT is applied to explore the ignition timing, bum duration, NOx production, gross indicated efficiency and gross IMEP of a supercharged engine (3 atm. Intake pressure) with 14:1, 16:l and 18:1 compression ratios at 1200 rpm. HCT has been modified to incorporate the effect of heat transfer and to calculate the temperature that results from mixing the recycled exhaust with the fresh mixture. This study uses a single control volume reaction zone that varies as a function of crank angle. The ignition process is controlled by adjusting the intake equivalence ratio and the residual gas trapping (RGT). RGT is internal exhaust gas recirculation which recycles both thermal energy and combustion product species. Adjustment of equivalence ratio and RGT is accomplished by varying the timing of the exhaust valve closure in either 2-stroke or 4-stroke engines. Inlet manifold temperature is held constant at 300 K. Results show that, for each compression ratio, there is a range of operational conditions that show promise of achieving the control necessary to vary power output while keeping indicated efficiency above 50% and NOx levels below 100 ppm. HCT results are also compared with a set of recent experimental data for natural gas.

  3. 7 CFR 400.162 - Qualification ratios.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Regulatory Information System” distributed by NAIC, 120 West 12th St., Kansas City, MO 64105-1925; (b) Three... Regulatory Information System (IRIS) ratios found in §§ 400.170(d)(1)(ii) and 400.170(d)(2) (i), (ii),...

  4. 34 CFR 668.172 - Financial ratios.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 34 Education 3 2014-07-01 2014-07-01 false Financial ratios. 668.172 Section 668.172 Education..., DEPARTMENT OF EDUCATION STUDENT ASSISTANCE GENERAL PROVISIONS Financial Responsibility § 668.172 Financial... program authorized by the HEA only if— (i) In the notes to the institution's audited financial...

  5. 34 CFR 668.172 - Financial ratios.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 34 Education 3 2013-07-01 2013-07-01 false Financial ratios. 668.172 Section 668.172 Education..., DEPARTMENT OF EDUCATION STUDENT ASSISTANCE GENERAL PROVISIONS Financial Responsibility § 668.172 Financial... program authorized by the HEA only if— (i) In the notes to the institution's audited financial...

  6. 34 CFR 668.172 - Financial ratios.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 34 Education 3 2011-07-01 2011-07-01 false Financial ratios. 668.172 Section 668.172 Education..., DEPARTMENT OF EDUCATION STUDENT ASSISTANCE GENERAL PROVISIONS Financial Responsibility § 668.172 Financial... program authorized by the HEA only if— (i) In the notes to the institution's audited financial...

  7. 34 CFR 668.172 - Financial ratios.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 34 Education 3 2012-07-01 2012-07-01 false Financial ratios. 668.172 Section 668.172 Education..., DEPARTMENT OF EDUCATION STUDENT ASSISTANCE GENERAL PROVISIONS Financial Responsibility § 668.172 Financial... program authorized by the HEA only if— (i) In the notes to the institution's audited financial...

  8. Flowmeter determines mix ratio for viscous adhesives

    NASA Technical Reports Server (NTRS)

    Lemons, C. R.

    1967-01-01

    Flowmeter determines mix ratio for continuous flow mixing machine used to produce an adhesive from a high viscosity resin and aliphatic amine hardener pumped through separate lines to a rotary blender. The flowmeter uses strain gages in the two flow paths and monitors their outputs with appropriate instrumentation.

  9. 78 FR 60559 - Pay Ratio Disclosure

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-01

    ... From the Federal Register Online via the Government Publishing Office ] Vol. 78 Tuesday, No. 190 October 1, 2013 Part IV Securities and Exchange Commission 17 CFR Parts 229 and 249 Pay Ratio Disclosure; Proposed Rule #0;#0;Federal Register / Vol. 78 , No. 190 / Tuesday, October 1, 2013 / Proposed...

  10. Helium isotope ratios in Easter microplate basalts

    NASA Astrophysics Data System (ADS)

    Poreda, R. J.; Schilling, J. G.; Craig, H.

    1993-09-01

    He-3/He-4 ratios in Easter Microplate basalt glasses show clear evidence of the effects of a mantle plume. The East Rift of the microplate between 26 and 28 deg S, identified by La/Sm, Sr and Pb isotopes and ridge crest elevation as the region of maximum plume influence, has He-3/He-4 ratios spanning the entire range from 7.5 to 11.7 R(sub A). The Easter Microplate is the only section of the entire East Pacific Rise that is associated with a known `hotspot' track (mantle plume) and has elevated He-3/He-4 ratios. Although most of the West Rift basalts contain MORB helium (8.0 - 8.7 (R sub A)), the basalt closest to the East Rift has an elevated He-3/He-4 ratio (11.3 R(sub A)), consistent with a significant plume component. The diversity in isotopic signatures also indicates that homogenization of isotopic anomalies does not occur, even in this region of `super-fast' spreading. The overall He-3/He-4-Pb-206/Pb-204 and He-3/He-4-Sr-87/Sr-86 trends have positive correlations, although the high between the He and Sr isotope distribution is modeled in the context of a plume source-migrating ridge sink. During channeling of the plume toward the ridge, helium if preferentially lost from the center of the channeled plume, resulting in lower He/Pb and He/Sr concentration ratios in the high He-3/He-4 component. Mixing trajectories in He-Sr isotopic space between a LILE depleted asthenosphere and a variably degassed plume component provide a reasonably good fit to the data and may explain the isotope systematics of plume-ridge interactions in the context of modern theories of plume dynamics.

  11. CHARACTERIZING TRITIUM WASTE USING HELIUM RATIOS

    SciTech Connect

    Ovink, R.W.; McMahon, W.J.; Borghese, J.V.; Olsen, K.B.

    2003-02-27

    When routine sampling revealed greatly elevated tritium levels (3.14 x 105 Bq/L [8.5-million pCi/liter]) in the groundwater near a solid waste landfill at the Hanford Site, an innovative technique was used to assess the extent of the plume. Helium-3/helium-4 ratios, relative to ambient air-in-soil gas samples, were used to identify the tritium source and initially delineate the extent of the groundwater tritium plume. This approach is a modification of a technique developed in the late 1960s to age-date deep ocean water as part of the GEOSECS ocean monitoring program. Poreda, et al. (1) and Schlosser, et al. (2) applied this modified technique to shallow aquifers. A study was also conducted to demonstrate the concept of using helium-3 as a tool to locate vadose zone sources of tritium and tracking groundwater tritium plumes at Hanford (3). Seventy sampling points were installed around the perimeter and along four transects downgradient of the burial ground. Soil gas samples were collected, analyzed for helium isotopes, and helium-3/helium-4 ratios were calculated for these 70 points. The helium ratios indicated a vadose zone source of tritium along the northern edge of the burial ground that is likely the source of tritium in the groundwater. The helium ratios also indicate the groundwater plume is traveling east-northeast from the burial ground and that no up-gradient tritium sources are affecting the burial ground. Based on the helium ratio results, six downgradient groundwater sampling locations were identified to verify the tritium plume extent and groundwater tritium concentrations. The tritium results from the initial groundwater samples confirmed that elevated helium ratios were indicative of tritium contamination in the local groundwater. The measurement of helium isotopes in soil gas provided a rapid and cost- effective technique to define the shape and extent of tritium contamination from the burial ground. Using this soil gas sampling approach, the

  12. Measure your septa release ratios: pheromone release ratio variability affected by rubber septa and solvent

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The type of solvent and volume of the solvent used to load pheromone/volatile components onto rubber septa had significant effects on release ratios, the variability of those release ratios, and the recoverability of the volatile components during subsequent extraction with hexane. Volatile release ...

  13. Econometric models for predicting confusion crop ratios

    NASA Technical Reports Server (NTRS)

    Umberger, D. E.; Proctor, M. H.; Clark, J. E.; Eisgruber, L. M.; Braschler, C. B. (Principal Investigator)

    1979-01-01

    Results for both the United States and Canada show that econometric models can provide estimates of confusion crop ratios that are more accurate than historical ratios. Whether these models can support the LACIE 90/90 accuracy criterion is uncertain. In the United States, experimenting with additional model formulations could provide improved methods models in some CRD's, particularly in winter wheat. Improved models may also be possible for the Canadian CD's. The more aggressive province/state models outperformed individual CD/CRD models. This result was expected partly because acreage statistics are based on sampling procedures, and the sampling precision declines from the province/state to the CD/CRD level. Declining sampling precision and the need to substitute province/state data for the CD/CRD data introduced measurement error into the CD/CRD models.

  14. Measuring Abundance Ratios from Integrated Light

    NASA Astrophysics Data System (ADS)

    Worthey, G.

    2010-06-01

    Age, overall abundance, and detailed, element-by-element abundances can be extracted from the integrated light of distant galaxies. The method, at its most basic, is merely the comparison of observed spectra with appropriate models. The relative ratios of elements C, N, O, Na, Mg, Ca, Sc, Ti, Cr, Mn, Fe, Co, Ni, Sr, and Ba can be determined to scientifically useful precision. Cases of interest that are borderline because they suffer internal degeneracies (although plenty of signal is present) are Al and the trio C, N, and O. The elements S, K, Cu, Eu, and the noble gases are too difficult to measure, and V is borderline. Changing the relative abundance ratios, even at fixed heavy-element content, changes the temperatures, luminosities, and number densities of the underlying stellar evolution, as well as more direct changes in the spectra of the stars present. The latter effects dominate the spectral shape, while the former effects render age estimation quite difficult.

  15. Maternal transmission, sex ratio distortion, and mitochondria.

    PubMed

    Perlman, Steve J; Hodson, Christina N; Hamilton, Phineas T; Opit, George P; Gowen, Brent E

    2015-08-18

    In virtually all multicellular eukaryotes, mitochondria are transmitted exclusively through one parent, usually the mother. In this short review, we discuss some of the major consequences of uniparental transmission of mitochondria, including deleterious effects in males and selection for increased transmission through females. Many of these consequences, particularly sex ratio distortion, have well-studied parallels in other maternally transmitted genetic elements, such as bacterial endosymbionts of arthropods. We also discuss the consequences of linkage between mitochondria and other maternally transmitted genetic elements, including the role of cytonuclear incompatibilities in maintaining polymorphism. Finally, as a case study, we discuss a recently discovered maternally transmitted sex ratio distortion in an insect that is associated with extraordinarily divergent mitochondria.

  16. The HNC/HCN ratio in comets

    NASA Technical Reports Server (NTRS)

    Irvine, W. M.; Dickens, J. E.; Lovell, A. J.; Schloerb, F. P.; Senay, M.; Bergin, E. A.; Jewitt, D.; Matthews, H. E.; Ferris, J. P. (Principal Investigator)

    1997-01-01

    The abundance ratio of the isomers HCN and HNC has been investigated in comet Hale-Bopp (C/1995 O1) through observations of the J = 4-3 rotational transitions of both species for heliocentric distances 0.93 < r < 3 AU, both pre- and post-perihelion. After correcting for the optical depth of the stronger HCN line, we find that the column density ratio of HNC/HCN in our telescope beam increases significantly as the comet approaches the Sun. We compare this behavior to that predicted from an ion-molecule chemical model and conclude that the HNC is produced in significant measure by chemical processes in the coma; i.e., for comet Hale-Bopp, HNC is not a parent molecule sublimating from the nucleus.

  17. Design of an ultrasmall aspect ratio concentrator

    NASA Astrophysics Data System (ADS)

    Cheng, Ying; Fang, Fengzhou; Zhang, Xiaodong

    2014-11-01

    The concentrated photovoltaic (CPV) can be employed to improve the efficiency of solar cells and reduce the system cost of power generation, which is the primary part of the CPV system. Based on the demands for the concentrators to have an ultrathin and ultralight design, a design of ultrasmall aspect ratio concentrators is proposed. The concentrator is formed by a lens array and a freeform reflector to precisely control the light. The solar cell is placed at the side of the concentrator, which greatly reduces the overall thickness of the concentrator. The design can reduce the aspect ratio of concentrator by a considerable amount. The freeform reflector can shape the light beam and achieve a uniform distribution of light energy.

  18. Gyromagnetic ratio of a massive body.

    NASA Technical Reports Server (NTRS)

    Cohen, J. M.; Tiomno, J.; Wald, R. M.

    1973-01-01

    It is well known that the gyromagnetic ratio (g factor) of a classical, slowly rotating body whose charge density is proportional to its mass density must be equal to unity. However, if the body is very massive, the spacetime curvature effects of general relativity become important and the result g = 1 is no longer valid. We calculate here the gyromagnetic ratio of a slowly rotating, massive shell with uniform charge density. When the shell is large compared with the Schwarzschild radius we have g = 1, but as the shell becomes more massive the g factor increases. In the limit as the shell approaches its Schwarzschild radius we obtain g approaching 2 (the same value as for an electron).

  19. Method for nanomachining high aspect ratio structures

    DOEpatents

    Yun, Wenbing; Spence, John; Padmore, Howard A.; MacDowell, Alastair A.; Howells, Malcolm R.

    2004-11-09

    A nanomachining method for producing high-aspect ratio precise nanostructures. The method begins by irradiating a wafer with an energetic charged-particle beam. Next, a layer of patterning material is deposited on one side of the wafer and a layer of etch stop or metal plating base is coated on the other side of the wafer. A desired pattern is generated in the patterning material on the top surface of the irradiated wafer using conventional electron-beam lithography techniques. Lastly, the wafer is placed in an appropriate chemical solution that produces a directional etch of the wafer only in the area from which the resist has been removed by the patterning process. The high mechanical strength of the wafer materials compared to the organic resists used in conventional lithography techniques with allows the transfer of the precise patterns into structures with aspect ratios much larger than those previously achievable.

  20. CFD Assessment of Orifice Aspect Ratio and Mass Flow Ratio on Jet Mixing in Rectangular Ducts

    NASA Technical Reports Server (NTRS)

    Bain, D. B.; Smith, C. E.; Holdeman, J. D.

    1994-01-01

    Isothermal CFD analysis was performed on axially opposed rows of jets mixing with cross flow in a rectangular duct. Laterally, the jets' centerlines were aligned with each other on the top and bottom walls. The focus of this study was to characterize the effects of orifice aspect ratio and jet-to-mainstream mass flow ratio on jet penetration and mixing. Orifice aspect ratios (L/W) of 4-to-1, 2-to-1, and 1-to-1, along with circular holes, were parametrically analyzed. Likewise, jet-to-mainstream mass flow ratios (MR) of 2.0, 0.5, and 0.25 were systematically investigated. The jet-to-mainstream momentum-flux ratio (J) was maintained at 36 for all cases, and the orifice spacing-to-duct height (S/H) was varied until optimum mixing was attained for each configuration. The numerical results showed that orifice aspect ratio (and likewise orifice blockage) had little effect on jet penetration and mixing. Based on mixing characteristics alone, the 4-to-1 slot was comparable to the circular orifice. The 4-to-1 slot has a smaller jet wake which may be advantageous for reducing emissions. However, the axial length of a 4-to-1 slot may be prohibitively long for practical application, especially for MR of 2.0. The jet-to-mainstream mass flow ratio had a more significant effect on jet penetration and mixing. For a 4-to-1 aspect ratio orifice, the design correlating parameter for optimum mixing (C = (S/H)(sq. root J)) varied from 2.25 for a mass flow ratio of 2.0 to 1.5 for a mass flow ratio of 0.25.

  1. Radiation and the sex ratio in man.

    PubMed

    SCHULL, W J; NEEL, J V

    1958-08-15

    An analysis of new data concerning the sex of children born to the survivors of the atomic bombings of Hiroshima and Nagasaki, together with a reanalysis of the data previously presented by Neel and Schull (9), reveals significant changes in the sex ratio of these children, changes in the direction to be expected if exposure had resulted in the induction of sex-linked lethal mutations (16).

  2. Polyatomic ions, branching ratios and hot molecules

    NASA Astrophysics Data System (ADS)

    Mitchell, J. Brian A.

    2015-01-01

    A discussion is given of the reason for the sharp fall-off observed in Dissociative Recombination (DR) cross sections above about 0.1 eV and of the need for accurate branching ratios being used in complex models of molecular ion chemistry. New measurements from TSR have shown that stored ions are not as cold as they were once thought to be and a new experiment facility is presented.

  3. Chen’s Double Eyelid Fold Ratio

    PubMed Central

    Chen, Chen-Chia; Tai, Hao-Chih

    2016-01-01

    Background: Double eyelidplasty can construct palpebral folds and enhance beauty perception for Asians with single eyelids. A new palpebral parameter for the quantitative interpretation of surgical outcomes is proposed on the basis of a photometric study of the altered proportions of Asian eyes after double eyelid operation. Methods: A total of 100 Asian adults with single upper eyelids who were satisfied with the enlarged eyes by operation were included in the study. A retrospective measurement of palpebral parameters in the frontal profile both preoperatively and 6 months postoperatively was performed. The proportions of various parameters in the eyebrow–eye aesthetic unit were calculated and analyzed. Results: Double eyelidplasty can augment the vertical dimension of palpebral fissure by 27.9% increase on average. The vertical ratio of palpebral fissure to the eyebrow–eye unit is augmented by 34.4% increase. The vertical ratio of the subunit below double eyelid fold peak to the unit is augmented by 82.6% increase. Conclusions: Double eyelidplasty can substantially enlarge the vertical dimensions of the eyes of Asians with single eyelids. The eyes are perceived to be larger because of the visually assimilated illusion of the superimposed eyelid fold and the relative proportions of the eyebrow–eye unit. The authors propose using a vertical ratio of the subunit below double eyelid fold peak in the eyebrow–eye unit to measure the visually perceived proportion of the eye in the unit. This ratio can be applied clinically for a quantitative evaluation of the surgical outcome after double eyelidplasty. PMID:27200243

  4. Theater SBI cost-effectiveness ratios

    SciTech Connect

    Canavan, G.H.

    1993-11-01

    To address M missiles spaced at intervals longer than the constillation reconstitution time t, the defense needs at the absentee ratio N{sub a} of SBIs to fill the belt plus the M SBIs needed for the intercepts; the resulting cost effectiveness scales as M/(M + N{sub a}). N{sub a} is large and CER small for small ranges and numbers of missiles. For several-hundred missile threats, CERs are greater than unity for ranges of interest.

  5. Factors affecting the aldosterone/renin ratio.

    PubMed

    Stowasser, M; Ahmed, A H; Pimenta, E; Taylor, P J; Gordon, R D

    2012-03-01

    Although the aldosterone/renin ratio (ARR) is the most reliable screening test for primary aldo-steronism, false positives and negatives occur. Dietary salt restriction, concomitant malignant or renovascular hypertension, pregnancy and treatment with diuretics (including spironolactone), dihydropyridine calcium blockers, angiotensin converting enzyme inhibitors, and angiotensin receptor antagonists can produce false negatives by stimulating renin. We recently reported selective serotonin reuptake inhibitors lower the ratio. Because potassium regulates aldosterone, uncorrected hypokalemia can lead to false negatives. Beta-blockers, alpha-methyldopa, clonidine, and nonsteroidal anti-inflammatory drugs suppress renin, raising the ARR with potential for false positives. False positives may occur in patients with renal dysfunction or advancing age. We recently showed that (1) females have higher ratios than males, and (2) false positive ratios can occur during the luteal menstrual phase and while taking an oral ethynylestradiol/drospirenone (but not implanted subdermal etonogestrel) contraceptive, but only if calculated using direct renin concentration and not plasma renin activity. Where feasible, diuretics should be ceased at least 6 weeks and other interfering medications at least 2 before ARR measurement, substituting noninterfering agents (e. g., verapamil slow-release±hydralazine and prazosin or doxazosin) were required. Hypokalemia should be corrected and a liberal salt diet encouraged. Collecting blood midmorning from seated patients following 2-4 h upright posture improves sensitivity. The ARR is a screening test only and should be repeated once or more before deciding whether to proceed to confirmatory suppression testing. Liquid chromatography-tandem mass spectrometry aldosterone assays represent a major advance towards addressing inaccuracies inherent in other available methods.

  6. Activity ratios of thorium daughters in vivo

    SciTech Connect

    Toohey, R.E.; Rundo, J.; Sha, J.Y.; Essling, M.A.; Pedersen, J.C.; Slane, J.M.

    1984-01-01

    A computerized method of least squares has been used to analyze the /sup 228/Ac and /sup 212/Pb-/sup 212/Bi and daughter ..gamma..-ray spectra obtained in vivo from 133 former workers at a thorium refinery. In addition, the exhalation rate of /sup 220/Rn was determined for each subject and expressed as pCi of emanating /sup 224/Ra. This value was added to the /sup 212/Pb value determined from the ..gamma..-ray measurements to obtain the total /sup 224/Ra present, and the ratio of /sup 224/Ra to /sup 228/Ac was calculated. Values of the ratio ranged from 0.52 +- 0.32 to 2.1 +- 1.7, with a weighted mean of 0.92 +- 0.17. However, it appears that the ratio observed in a given case is characteristic for that case alone; the computed mean value may not be meaningful. The least squares fitting procedure and the overall calibration of the counting system were validated by measurements of /sup 224/Ra in the lungs of one subject postmortem, compared with results obtained from the same subject in vivo. 6 references, 5 figures.

  7. Omniclassical Diffusion in Low Aspect Ratio Tokamaks

    SciTech Connect

    H.E. Mynick; R.B. White; D.A. Gates

    2004-03-19

    Recently reported numerical results for axisymmetric devices with low aspect ratio A found radial transport enhanced over the expected neoclassical value by a factor of 2 to 3. In this paper, we provide an explanation for this enhancement. Transport theory in toroidal devices usually assumes large A, and that the ratio B{sub p}/B{sub t} of the poloidal to the toroidal magnetic field is small. These assumptions result in transport which, in the low collision limit, is dominated by banana orbits, giving the largest collisionless excursion of a particle from an initial flux surface. However in a small aspect ratio device one may have B{sub p}/B{sub t} {approx} 1, and the gyroradius may be larger than the banana excursion. Here, we develop an approximate analytic transport theory valid for devices with arbitrary A. For low A, we find that the enhanced transport, referred to as omniclassical, is a combination of neoclassical and properly generalized classical effects, which become dominant in the low-A, B{sub p}/B{sub t} {approx} 1 regime. Good agreement of the analytic theory with numerical simulations is obtained.

  8. Ocean nutrient ratios governed by plankton biogeography.

    PubMed

    Weber, Thomas S; Deutsch, Curtis

    2010-09-30

    The major nutrients nitrate and phosphate have one of the strongest correlations in the sea, with a slope similar to the average nitrogen (N) to phosphorus (P) content of plankton biomass (N/P = 16:1). The processes through which this global relationship emerges despite the wide range of N/P ratios at the organism level are not known. Here we use an ocean circulation model and observed nutrient distributions to show that the N/P ratio of biological nutrient removal varies across latitude in Southern Ocean surface waters, from 12:1 in the polar ocean to 20:1 in the sub-Antarctic zone. These variations are governed by regional differences in the species composition of the plankton community. The covariation of dissolved nitrate and phosphate is maintained by ocean circulation, which mixes the shallow subsurface nutrients between distinct biogeographic provinces. Climate-driven shifts in these marine biomes may alter the mean N/P ratio and the associated carbon export by Southern Ocean ecosystems.

  9. Critical Concentration Ratio for Solar Thermoelectric Generators

    NASA Astrophysics Data System (ADS)

    ur Rehman, Naveed; Siddiqui, Mubashir Ali

    2016-10-01

    A correlation for determining the critical concentration ratio (CCR) of solar concentrated thermoelectric generators (SCTEGs) has been established, and the significance of the contributing parameters is discussed in detail. For any SCTEG, higher concentration ratio leads to higher temperatures at the hot side of modules. However, the maximum value of this temperature for safe operation is limited by the material properties of the modules and should be considered as an important design constraint. Taking into account this limitation, the CCR can be defined as the maximum concentration ratio usable for a particular SCTEG. The established correlation is based on factors associated with the material and geometric properties of modules, thermal characteristics of the receiver, installation site attributes, and thermal and electrical operating conditions. To reduce the number of terms in the correlation, these factors are combined to form dimensionless groups by applying the Buckingham Pi theorem. A correlation model containing these groups is proposed and fit to a dataset obtained by simulating a thermodynamic (physical) model over sampled values acquired by applying the Latin hypercube sampling (LHS) technique over a realistic distribution of factors. The coefficient of determination and relative error are found to be 97% and ±20%, respectively. The correlation is validated by comparing the predicted results with literature values. In addition, the significance and effects of the Pi groups on the CCR are evaluated and thoroughly discussed. This study will lead to a wide range of opportunities regarding design and optimization of SCTEGs.

  10. Poisson's ratio over two centuries: challenging hypotheses

    PubMed Central

    Greaves, G. Neville

    2013-01-01

    This article explores Poisson's ratio, starting with the controversy concerning its magnitude and uniqueness in the context of the molecular and continuum hypotheses competing in the development of elasticity theory in the nineteenth century, moving on to its place in the development of materials science and engineering in the twentieth century, and concluding with its recent re-emergence as a universal metric for the mechanical performance of materials on any length scale. During these episodes France lost its scientific pre-eminence as paradigms switched from mathematical to observational, and accurate experiments became the prerequisite for scientific advance. The emergence of the engineering of metals followed, and subsequently the invention of composites—both somewhat separated from the discovery of quantum mechanics and crystallography, and illustrating the bifurcation of technology and science. Nowadays disciplines are reconnecting in the face of new scientific demands. During the past two centuries, though, the shape versus volume concept embedded in Poisson's ratio has remained invariant, but its application has exploded from its origins in describing the elastic response of solids and liquids, into areas such as materials with negative Poisson's ratio, brittleness, glass formation, and a re-evaluation of traditional materials. Moreover, the two contentious hypotheses have been reconciled in their complementarity within the hierarchical structure of materials and through computational modelling. PMID:24687094

  11. Noise of Embedded High Aspect Ratio Nozzles

    NASA Technical Reports Server (NTRS)

    Bridges, James E.

    2011-01-01

    A family of high aspect ratio nozzles were designed to provide a parametric database of canonical embedded propulsion concepts. Nozzle throat geometries with aspect ratios of 2:1, 4:1, and 8:1 were chosen, all with convergent nozzle areas. The transition from the typical round duct to the rectangular nozzle was designed very carefully to produce a flow at the nozzle exit that was uniform and free from swirl. Once the basic rectangular nozzles were designed, external features common to embedded propulsion systems were added: extended lower lip (a.k.a. bevel, aft deck), differing sidewalls, and chevrons. For the latter detailed Reynolds-averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) simulations were made to predict the thrust performance and to optimize parameters such as bevel length, and chevron penetration and azimuthal curvature. Seventeen of these nozzles were fabricated at a scale providing a 2.13 inch diameter equivalent area throat." ! The seventeen nozzles were tested for far-field noise and a few data were presented here on the effect of aspect ratio, bevel length, and chevron count and penetration. The sound field of the 2:1 aspect ratio rectangular jet was very nearly axisymmetric, but the 4:1 and 8:1 were not, the noise on their minor axes being louder than the major axes. Adding bevel length increased the noise of these nozzles, especially on their minor axes, both toward the long and short sides of the beveled nozzle. Chevrons were only added to the 2:1 rectangular jet. Adding 4 chevrons per wide side produced some decrease at aft angles, but increased the high frequency noise at right angles to the jet flow. This trend increased with increasing chevron penetration. Doubling the number of chevrons while maintaining their penetration decreased these effects. Empirical models of the parametric effect of these nozzles were constructed and quantify the trends stated above." Because it is the objective of the Supersonics Project that

  12. Nutrient Provinces in the Sea: Concentration Ratios, Reaction Rate Ratios, and Ideal Covariation

    NASA Astrophysics Data System (ADS)

    Fanning, Kent A.

    1992-04-01

    Global distributions of the ratios of the concentrations of nitrate + nitrite (= [N]) and phosphate (= [P]) are evaluated from Geochemical Ocean Sections Study (GEOSECS) and Transient Tracers in the Ocean (TTO) data sets. If large oceanic regions (or provinces) can be identified on the basis of constant [N]: [P] ratios, then the distribution equation for a reactive variable shows that the ratio of the net reaction rates involving N and P in each one is equal to its concentration ratio. Organisms within the interiors of the provinces would then be in balance with the ratios in which the nutrients are present, producing a non-fractionated or "ideal" nutrient covariation. Such provinces can be observed throughout the ocean. Notable features are as follows: (1) Between the euphotic zone and 500 m in the west central North Atlantic is a large region in which N-P regeneration produces very high [N]:[P] ratios: ˜50 mol mol-1. Potential causes are 18° Water formation, coccolithophorid growth, nitrogen fixation, or atmospheric fixed-nitrogen deposition. (2) Most oligotrophic surface waters seem to have [N]:[P] between 0 and 3 mol mol-1, implying that the net removal ratio of N and P in those waters is 0-3 mol mol-1. (3) Below 600 m, the ocean contains large provinces with N-P regeneration ratios of 12-18 mol mol-1. The dominant ratio is slightly sub-Redfield at 14.5-15 mol mol-1, with the entire Indian Ocean below 3000 m being ideally covariant at 14.7 mol mol-1. The northeastern Pacific has provinces with very low regeneration ratios (<14 mol mol-1). Vertical boundaries between deep provinces in the western Pacific and eastern Atlantic suggest that particles from immediately above control regeneration ratios, whereas the more horizontal boundaries between western Atlantic provinces appear to reflect a greater importance of horizontally transported particles in water masses like Antarctic Intermediate Water. N-P reaction rate ratios along deep isopycnal surfaces are quite

  13. 45 CFR 800.203 - Medical loss ratio.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 45 Public Welfare 3 2013-10-01 2013-10-01 false Medical loss ratio. 800.203 Section 800.203 Public... PROGRAM Premiums, Rating Factors, Medical Loss Ratios, and Risk Adjustment § 800.203 Medical loss ratio. (a) Required medical loss ratio. An MSPP issuer must attain: (1) The medical loss ratio...

  14. 42 CFR 403.250 - Loss ratio calculations: General provisions.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 42 Public Health 2 2012-10-01 2012-10-01 false Loss ratio calculations: General provisions. 403... Certification Program: Loss Ratio Provisions § 403.250 Loss ratio calculations: General provisions. (a) Basic formula. The expected loss ratio is calculated by determining the ratio of benefits to premiums....

  15. 42 CFR 403.250 - Loss ratio calculations: General provisions.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 42 Public Health 2 2010-10-01 2010-10-01 false Loss ratio calculations: General provisions. 403... Certification Program: Loss Ratio Provisions § 403.250 Loss ratio calculations: General provisions. (a) Basic formula. The expected loss ratio is calculated by determining the ratio of benefits to premiums....

  16. 42 CFR 403.250 - Loss ratio calculations: General provisions.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 42 Public Health 2 2014-10-01 2014-10-01 false Loss ratio calculations: General provisions. 403... Certification Program: Loss Ratio Provisions § 403.250 Loss ratio calculations: General provisions. (a) Basic formula. The expected loss ratio is calculated by determining the ratio of benefits to premiums....

  17. 42 CFR 403.250 - Loss ratio calculations: General provisions.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 42 Public Health 2 2011-10-01 2011-10-01 false Loss ratio calculations: General provisions. 403... Certification Program: Loss Ratio Provisions § 403.250 Loss ratio calculations: General provisions. (a) Basic formula. The expected loss ratio is calculated by determining the ratio of benefits to premiums....

  18. 42 CFR 403.250 - Loss ratio calculations: General provisions.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 42 Public Health 2 2013-10-01 2013-10-01 false Loss ratio calculations: General provisions. 403... Certification Program: Loss Ratio Provisions § 403.250 Loss ratio calculations: General provisions. (a) Basic formula. The expected loss ratio is calculated by determining the ratio of benefits to premiums....

  19. 45 CFR 800.203 - Medical loss ratio.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 45 Public Welfare 3 2014-10-01 2014-10-01 false Medical loss ratio. 800.203 Section 800.203 Public... PROGRAM Premiums, Rating Factors, Medical Loss Ratios, and Risk Adjustment § 800.203 Medical loss ratio. (a) Required medical loss ratio. An MSPP issuer must attain: (1) The medical loss ratio...

  20. 12 CFR 3.6 - Minimum capital ratios.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 12 Banks and Banking 1 2012-01-01 2012-01-01 false Minimum capital ratios. 3.6 Section 3.6 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY MINIMUM CAPITAL RATIOS; ISSUANCE OF DIRECTIVES Minimum Capital Ratios § 3.6 Minimum capital ratios. (a) Risk-based capital ratio....

  1. Cytoplasm-to-myonucleus ratios following microgravity

    NASA Technical Reports Server (NTRS)

    Kasper, C. E.; Xun, L.

    1996-01-01

    The cytoplasmic volume-to-myonucleus ratio in the tibialis anterior and gastrocnemius muscles of juvenile rats after 5.4 days of microgravity was studied. Three groups of rats (n = 8 each) were used. The experimental group (space rats) was flown aboard the space shuttle Discovery (NASA, STS-48), while two ground-based groups, one hindlimb suspended (suspended rats), one non-suspended (control), served as controls. Single fibre analysis revealed a significant decrease in cross-sectional area (microns2) in the gastrocnemius for both the space and the suspended rats; in the tibialis anterior only the suspended rats showed a significant decrease. Myonuclei counts (myonuclei per mm) in both the tibialis anterior and gastrocnemius were significantly increased in the space rats but not in the suspended rats. The mean myonuclear volume (individual nuclei: microns3) in tibialis anterior fibres from the space rats, and in gastrocnemius fibres from both the space and the suspended rats, was significantly lower than that in the respective control group. Estimation of the total myonuclear volume (microns3 per.mm), however, revealed no significant differences between the three groups in either the tibialis anterior or gastrocnemius. The described changes in the cross-sectional area and myonuclei numbers resulted in significant decreases in the cytoplasmic volume-to-myonucleus ratio (microns3 x 10(3)) in both muscles and for both space and suspended rats (tibialis anterior; 15.6 +/- 0.6 (space), 17.2 +/- 1.0 (suspended), 20.8 +/- 0.9 (control): gastrocnemius; 13.4 +/- 0.4 (space) and 14.9 +/- 1.1 (suspended) versus 18.1 +/- 1.1 (control)). These results indicate that even short periods of unweighting due to microgravity or limb suspension result in changes in skeletal muscle fibres which lead to significant decreases in the cytoplasmic volume-to-myonucleus ratio.

  2. Sex Ratios at Birth and Environmental Temperatures

    NASA Astrophysics Data System (ADS)

    Lerchl, Alexander

    The relationship between average monthly air temperature and sex ratios at birth (SRB) was analyzed for children born in Germany during the period 1946-1995. Both the absolute temperature and - more markedly - the monthly temperature deviations from the overall mean were significantly positively correlated with the SRB (P<0.01) when temperatures were time-lagged against the SRB data by -10 or -11months. It is concluded that the sex of the offspring is partially determined by environmental temperatures prior to conception.

  3. Flutter analysis of low aspect ratio wings

    NASA Technical Reports Server (NTRS)

    Parnell, L. A.

    1986-01-01

    Several very low aspect ratio flat plate wing configurations are analyzed for their aerodynamic instability (flutter) characteristics. All of the wings investigated are delta planforms with clipped tips, made of aluminum alloy plate and cantilevered from the supporting vehicle body. Results of both subsonic and supersonic NASTRAN aeroelastic analyses as well as those from another version of the program implementing the supersonic linearized aerodynamic theory are presented. Results are selectively compared with the experimental data; however, supersonic predictions of the Mach Box method in NASTRAN are found to be erratic and erroneous, requiring the use of a separate program.

  4. The transverse Poisson's ratio of composites.

    NASA Technical Reports Server (NTRS)

    Foye, R. L.

    1972-01-01

    An expression is developed that makes possible the prediction of Poisson's ratio for unidirectional composites with reference to any pair of orthogonal axes that are normal to the direction of the reinforcing fibers. This prediction appears to be a reasonable one in that it follows the trends of the finite element analysis and the bounding estimates, and has the correct limiting value for zero fiber content. It can only be expected to apply to composites containing stiff, circular, isotropic fibers bonded to a soft matrix material.

  5. CO (Carbon Monoxide Mixing Ratio System) Handbook

    SciTech Connect

    Biraud, S

    2011-02-23

    The main function of the CO instrument is to provide continuous accurate measurements of carbon monoxide mixing ratio at the ARM SGP Central Facility (CF) 60-meter tower (36.607 °N, 97.489 °W, 314 meters above sea level). The essential feature of the control and data acquisition system is to record signals from a Thermo Electron 48C and periodically calibrate out zero and span drifts in the instrument using the combination of a CO scrubber and two concentrations of span gas (100 and 300 ppb CO in air). The system was deployed on May 25, 2005.

  6. High aspect ratio, remote controlled pumping assembly

    DOEpatents

    Brown, S.B.; Milanovich, F.P.

    1995-11-14

    A miniature dual syringe-type pump assembly is described which has a high aspect ratio and which is remotely controlled, for use such as in a small diameter penetrometer cone or well packer used in water contamination applications. The pump assembly may be used to supply and remove a reagent to a water contamination sensor, for example, and includes a motor, gearhead and motor encoder assembly for turning a drive screw for an actuator which provides pushing on one syringe and pulling on the other syringe for injecting new reagent and withdrawing used reagent from an associated sensor. 4 figs.

  7. High aspect ratio, remote controlled pumping assembly

    DOEpatents

    Brown, Steve B.; Milanovich, Fred P.

    1995-01-01

    A miniature dual syringe-type pump assembly which has a high aspect ratio and which is remotely controlled, for use such as in a small diameter penetrometer cone or well packer used in water contamination applications. The pump assembly may be used to supply and remove a reagent to a water contamination sensor, for example, and includes a motor, gearhead and motor encoder assembly for turning a drive screw for an actuator which provides pushing on one syringe and pulling on the other syringe for injecting new reagent and withdrawing used reagent from an associated sensor.

  8. Energy Balance Bowen Ratio Station (EBBR) Handbook

    SciTech Connect

    Cook, DR

    2011-02-23

    The energy balance Bowen ratio (EBBR) system produces 30-minute estimates of the vertical fluxes of sensible and latent heat at the local surface. Flux estimates are calculated from observations of net radiation, soil surface heat flux, and the vertical gradients of temperature and relative humidity (RH). Meteorological data collected by the EBBR are used to calculate bulk aerodynamic fluxes, which are used in the Bulk Aerodynamic Technique (BA) EBBR value-added product (VAP) to replace sunrise and sunset spikes in the flux data. A unique aspect of the system is the automatic exchange mechanism (AEM), which helps to reduce errors from instrument offset drift.

  9. Energy Balance Bowen Ratio (EBBR) Handbook

    SciTech Connect

    Cook, D. R.

    2016-01-01

    The Energy Balance Bowen Ratio (EBBR) system produces 30-minute estimates of the vertical fluxes of sensible and latent heat at the local surface. Flux estimates are calculated from observations of net radiation, soil surface heat flux, and the vertical gradients of temperature and relative humidity (RH). Meteorological data collected by the EBBR are used to calculate bulk aerodynamic fluxes, which are used in the Bulk Aerodynamic Technique (BA) EBBR value-added product (VAP) to replace sunrise and sunset spikes in the flux data. A unique aspect of the system is the automatic exchange mechanism (AEM), which helps to reduce errors from instrument offset drift.

  10. Implications of Fast Reactor Transuranic Conversion Ratio

    SciTech Connect

    Steven J. Piet; Edward A. Hoffman; Samuel E. Bays

    2010-11-01

    Theoretically, the transuranic conversion ratio (CR), i.e. the transuranic production divided by transuranic destruction, in a fast reactor can range from near zero to about 1.9, which is the average neutron yield from Pu239 minus 1. In practice, the possible range will be somewhat less. We have studied the implications of transuranic conversion ratio of 0.0 to 1.7 using the fresh and discharge fuel compositions calculated elsewhere. The corresponding fissile breeding ratio ranges from 0.2 to 1.6. The cases below CR=1 (“burners”) do not have blankets; the cases above CR=1 (“breeders”) have breeding blankets. The burnup was allowed to float while holding the maximum fluence to the cladding constant. We graph the fuel burnup and composition change. As a function of transuranic conversion ratio, we calculate and graph the heat, gamma, and neutron emission of fresh fuel; whether the material is “attractive” for direct weapon use using published criteria; the uranium utilization and rate of consumption of natural uranium; and the long-term radiotoxicity after fuel discharge. For context, other cases and analyses are included, primarily once-through light water reactor (LWR) uranium oxide fuel at 51 MWth-day/kg-iHM burnup (UOX-51). For CR<1, the heat, gamma, and neutron emission increase as material is recycled. The uranium utilization is at or below 1%, just as it is in thermal reactors as both types of reactors require continuing fissile support. For CR>1, heat, gamma, and neutron emission decrease with recycling. The uranium utilization exceeds 1%, especially as all the transuranic elements are recycled. exceeds 1%, especially as all the transuranic elements are recycled. At the system equilibrium, heat and gamma vary by somewhat over an order of magnitude as a function of CR. Isotopes that dominate heat and gamma emission are scattered throughout the actinide chain, so the modest impact of CR is unsurprising. Neutron emitters are preferentially found

  11. DPOAE generation dependence on primary frequencies ratio

    NASA Astrophysics Data System (ADS)

    Botti, Teresa; Sisto, Renata; Moleti, Arturo; D'Amato, Luisa; Sanjust, Filippo

    2015-12-01

    Two different mechanisms are responsible for the DPOAE generation. The nonlinear distortion wave-fixed mechanism generates the DPOAE Zero-Latency (ZL) component, as a backward traveling wave from the "overlap" region. Linear reflection of the forward DP wave (IDP) generates the DPOAE Long-Latency (LL) component through a place-fixed mechanism. ZL and LL components add up vectorially to generate the DPOAE recorded in the ear canal. The 2f1 - f2 and 2f2 - f1 DPOAE intensity depends on the stimulus level and on the primary frequency ratio r = f2/f1, where f1 and f2 are the primary stimuli frequencies. Here we study the behavior of the ZL and LL DPOAE components as a function of r by both numerical and laboratory experiments, measuring DPAOEs with an equal primary levels (L1 = L2) paradigm in the range [35, 75] dB SPL, with r ranging in [1.1, 1.45]. Numerical simulations of a nonlocal nonlinear model have been performed without cochlear roughness, to suppress the linear reflection mechanism. In this way the model solution at the base represents the DPOAE ZL component, and the solution at the corresponding DPOAE tonotopic place corresponds to the IDP. This technique has been not effectual to study the 2f2 - f1 DPOAE, as a consequence of its generation mechanism. While the 2f1 - f2 generation place is known to be the tonotopic place x(f2), the 2f2 - f1 DPOAE one has to be assumed basal to its corresponding reflection place. That is because ZL components generated in x(f2) cannot significantly pass through their resonant place. Moreover increasing the ratio r, 2f2 - f1 ZL and LL generation place approach each other, because the overlap region of primary tones decreases. Consequently, the distinction between the two places becomes complicated. DPOAEs have been measured in six young normal-hearing subjects. DPOAE ZL and LL components have been separated by a time-frequency filtering method based on the wavelet transform 1. due to their different phase gradient delay

  12. Does the Mother or Father Determine the Offspring Sex Ratio? Investigating the Relationship between Maternal Digit Ratio and Offspring Sex Ratio

    PubMed Central

    Kim, Tae Beom; Oh, Jin Kyu; Kim, Kwang Taek; Yoon, Sang Jin; Kim, Soo Woong

    2015-01-01

    Objective In mammals, high parental testosterone levels present around the time of conception are thought to skew offspring sex ratio toward sons. The second to fourth digit ratio (digit ratio) is now widely accepted as a negative correlate of prenatal testosterone. Thus, we investigated the association between digit ratio and offspring sex ratio. Methods A total of 508 Korean patients (257 males and 251 females) less than 60 years old who had one or more offspring were prospectively enrolled. The lengths of the 2nd and 4th digits of the right hand were measured by a single investigator using a digital vernier calliper. Next, the patients’ lifetime offspring birth sex ratios were investigated. Results Maternal (rather than paternal) digit ratio was significantly associated with the number of sons (r = -0.153, p = 0.015), number of daughters (r = 0.130, p = 0.039), and offspring sex ratio (r = -0.171, p = 0.007). And, the maternal digit ratio was a significant factor for predicting offspring sex ratio (B = -1.620, p = 0.008) on multiple linear regression analysis. The female patients with a lower digit ratio (< 0.95) were found to have a higher offspring sex ratio (0.609 versus 0.521, p = 0.046) compared to those with a higher digit ratio (≥ 0.95). Furthermore, females in the low digit ratio group have a probability 1.138 greater of having sons than females in the high digit ratio group. Conclusions Maternal digit ratio was negatively associated with offspring sex ratio. Females with a lower digit ratio were more likely to have more male offspring compared to those with a higher digit ratio. Thus, our results suggest that the sex of offspring might be more influenced by maternal rather than paternal factors. PMID:26575995

  13. Intragenomic conflict produces sex ratio dynamics that favor maternal sex ratio distorters.

    PubMed

    Rood, Elaine S; Freedberg, Steven

    2016-11-01

    Maternal sex ratio distorters (MSDs) are selfish elements that enhance their transmission by biasing their host's sex allocation in favor of females. While previous models have predicted that the female-biased populations resulting from sex ratio distortion can benefit from enhanced productivity, these models neglect Fisherian selection for nuclear suppressors, an unrealistic assumption in most systems. We used individual-based computer simulation modeling to explore the intragenomic conflict between sex ratio distorters and their suppressors and explored the impacts of these dynamics on population-level competition between species characterized by MSDs and those lacking them. The conflict between distorters and suppressors was capable of producing large cyclical fluctuations in the population sex ratio and reproductive rate. Despite fitness costs associated with the distorters and suppressors, MSD populations often exhibited enhanced productivity and outcompeted non-MSD populations in single and multiple-population competition simulations. Notably, the conflict itself is beneficial to the success of populations, as sex ratio oscillations limit the competitive deficits associated with prolonged periods of male rarity. Although intragenomic conflict has been historically viewed as deleterious to populations, our results suggest that distorter-suppressor conflict can provide population-level advantages, potentially helping to explain the persistence of sex ratio distorters in a range of taxa.

  14. Complications with using ratios for environmental data: Comparing enantiomeric ratios (ERs) and enantiomer fractions (EFs)

    USGS Publications Warehouse

    Ulrich, E.M.; Helsel, D.R.; Foreman, W.T.

    2003-01-01

    Complications arise when ratios are used to present environmental data because ratios are an unbounded, multiplicative scale that can lead to asymmetrical (skewed) data distributions. Enantiomeric ratios (ERs), historically used in discussions of chiral signatures, often are published as mean ER??single-value standard deviation. Application of statistical summaries, such as the widely used sample mean and standard deviation, to skewed ratio data is misleading and often inappropriate. Comparison of statistically summarized ER and enantiomer fraction (EF) data (which are based on a bounded, additive scale) for a range of hypothetical values reveals substantial discrepancies when conversion between ER and EF formats is used. These discrepancies are largest when the ratio data are greater than one and have large variability, because the data are more skewed. In many cases, the use of fractions instead of ratios can help to minimize misrepresentation of environmental data, including chiral data. The use of nonparametric statistical summaries, e.g., median and percentiles, provides a more robust indicator of the typical value and spread for both ER and EF data. ?? 2003 Elsevier Ltd. All rights reserved.

  15. Hydraulic system for a ratio change transmission

    DOEpatents

    Kalns, Ilmars

    1981-01-01

    Disclosed is a drive assembly (10) for an electrically powered vehicle (12). The assembly includes a transaxle (16) having a two-speed transmission (40) and a drive axle differential (46) disposed in a unitary housing assembly (38), an oil-cooled prime mover or electric motor (14) for driving the transmission input shaft (42), an adapter assembly (24) for supporting the prime mover on the transaxle housing assembly, and a hydraulic system (172) providing pressurized oil flow for cooling and lubricating the electric motor and transaxle and for operating a clutch (84) and a brake (86) in the transmission to shift between the two-speed ratios of the transmission. The adapter assembly allows the prime mover to be supported in several positions on the transaxle housing. The brake is spring-applied and locks the transmission in its low-speed ratio should the hydraulic system fail. The hydraulic system pump is driven by an electric motor (212) independent of the prime mover and transaxle.

  16. Flexible Conversion Ratio Fast Reactor Systems Evaluation

    SciTech Connect

    Neil Todreas; Pavel Hejzlar

    2008-06-30

    Conceptual designs of lead-cooled and liquid salt-cooled fast flexible conversion ratio reactors were developed. Both concepts have cores reated at 2400 MWt placed in a large-pool-type vessel with dual-free level, which also contains four intermediate heat exchanges coupling a primary coolant to a compact and efficient supercritical CO2 Brayton cycle power conversion system. Decay heat is removed passively using an enhanced Reactor Vessel Auxiliary Cooling System and a Passive Secondary Auxiliary Cooling System. The most important findings were that (1) it is feasible to design the lead-cooled and salt-cooled reactor with the flexible conversion ratio (CR) in the range of CR=0 and CR=1 n a manner that achieves inherent reactor shutdown in unprotected accidents, (2) the salt-cooled reactor requires Lithium thermal Expansion Modules to overcme the inherent salt coolant's large positive coolant temperature reactivity coefficient, (3) the preferable salt for fast spectrum high power density cores is NaCl-Kcl-MgCl2 as opposed to fluoride salts due to its better themal-hydraulic and neutronic characteristics, and (4) both reactor, but attain power density 3 times smaller than that of the sodium-cooled reactor.

  17. Edge ratio and community structure in networks

    NASA Astrophysics Data System (ADS)

    Cafieri, Sonia; Hansen, Pierre; Liberti, Leo

    2010-02-01

    A hierarchical divisive algorithm is proposed for identifying communities in complex networks. To that effect, the definition of community in the weak sense of Radicchi [Proc. Natl. Acad. Sci. U.S.A. 101, 2658 (2004)] is extended into a criterion for a bipartition to be optimal: one seeks to maximize the minimum for both classes of the bipartition of the ratio of inner edges to cut edges. A mathematical program is used within a dichotomous search to do this in an optimal way for each bipartition. This includes an exact solution of the problem of detecting indivisible communities. The resulting hierarchical divisive algorithm is compared with exact modularity maximization on both artificial and real world data sets. For two problems of the former kind optimal solutions are found; for five problems of the latter kind the edge ratio algorithm always appears to be competitive. Moreover, it provides additional information in several cases, notably through the use of the dendrogram summarizing the resolution. Finally, both algorithms are compared on reduced versions of the data sets of Girvan and Newman [Proc. Natl. Acad. Sci. U.S.A. 99, 7821 (2002)] and of Lancichinetti [Phys. Rev. E 78, 046110 (2008)]. Results for these instances appear to be comparable.

  18. Ratio model serves suprathreshold color- luminance discrimination

    NASA Astrophysics Data System (ADS)

    Sankeralli, Marcel J.; Mullen, Kathy T.; Hine, Trevor J.

    2002-03-01

    We extended earlier results [J. Opt. Soc. Am. A 16, 2625 (1999)] to examine how the responses of the three postreceptoral mechanisms are combined to subserve discrimination of suprathreshold stimuli. Test thresholds were obtained in the presence of suprathreshold pedestals selected in different quadrants of the red-green/luminance and blue-yellow/luminance planes of cardinal color space. We showed that (1) test threshold was directly proportional to pedestal contrast for pedestal contrasts exceeding five times pedestal contrast threshold, and (2) there were exceptions to this proportionality, notably when the test and pedestal directions were fixed in the cardinal directions. Results support a ratio model of suprathreshold color-luminance discrimination, in which discrimination depends on a ratio of outputs of the postreceptoral mechanisms. We also observed that when test threshold was measured as a function of test color-space direction, masking by the achromatic component of the pedestal was less than that by the chromatic component. In addition, masking by a dark (negative luminance component) pedestal was lower than masking by a light (positive luminance) pedestal of a similar contrast. Our results demonstrated that (1) there is no fundamental difference between discrimination in the isoluminant and in the two chromoluminant cardinal planes, (2) there exists the possibility that discrimination in cardinal directions differs from that in noncardinal (intermediate) directions, and (3) suprathreshold discrimination of luminance differences may be more sensitive than that of chromatic differences for a given suprathreshold pedestal.

  19. Finger Length Ratios in Serbian Transsexuals

    PubMed Central

    Vujović, Svetlana; Popović, Srdjan; Mrvošević Marojević, Ljiljana; Ivović, Miomira; Tančić-Gajić, Milina; Stojanović, Miloš; Marina, Ljiljana V.; Barać, Marija; Barać, Branko; Kovačević, Milena; Duišin, Dragana; Barišić, Jasmina; Djordjević, Miroslav L.; Micić, Dragan

    2014-01-01

    Atypical prenatal hormone exposure could be a factor in the development of transsexualism. There is evidence that the 2nd and 4th digit ratio (2D : 4D) associates negatively with prenatal testosterone and positively with estrogens. The aim was to assess the difference in 2D : 4D between female to male transsexuals (FMT) and male to female transsexuals (MFT) and controls. We examined 42 MFT, 38 FMT, and 45 control males and 48 control females. Precise measurements were made by X-rays at the ventral surface of both hands from the basal crease of the digit to the tip using vernier calliper. Control male and female patients had larger 2D : 4D of the right hand when compared to the left hand. Control male's left hand ratio was lower than in control female's left hand. There was no difference in 2D : 4D between MFT and control males. MFT showed similar 2D : 4D of the right hand with control women indicating possible influencing factor in embryogenesis and consequently finger length changes. FMT showed the lowest 2D : 4D of the left hand when compared to the control males and females. Results of our study go in favour of the biological aetiology of transsexualism. PMID:24982993

  20. Finger length ratios in Serbian transsexuals.

    PubMed

    Vujović, Svetlana; Popović, Srdjan; Mrvošević Marojević, Ljiljana; Ivović, Miomira; Tančić-Gajić, Milina; Stojanović, Miloš; Marina, Ljiljana V; Barać, Marija; Barać, Branko; Kovačević, Milena; Duišin, Dragana; Barišić, Jasmina; Djordjević, Miroslav L; Micić, Dragan

    2014-01-01

    Atypical prenatal hormone exposure could be a factor in the development of transsexualism. There is evidence that the 2nd and 4th digit ratio (2D:4D) associates negatively with prenatal testosterone and positively with estrogens. The aim was to assess the difference in 2D:4D between female to male transsexuals (FMT) and male to female transsexuals (MFT) and controls. We examined 42 MFT, 38 FMT, and 45 control males and 48 control females. Precise measurements were made by X-rays at the ventral surface of both hands from the basal crease of the digit to the tip using vernier calliper. Control male and female patients had larger 2D:4D of the right hand when compared to the left hand. Control male's left hand ratio was lower than in control female's left hand. There was no difference in 2D:4D between MFT and control males. MFT showed similar 2D:4D of the right hand with control women indicating possible influencing factor in embryogenesis and consequently finger length changes. FMT showed the lowest 2D:4D of the left hand when compared to the control males and females. Results of our study go in favour of the biological aetiology of transsexualism.

  1. The basic reproductive ratio of life

    PubMed Central

    Manapat, Michael L.; Chen, Irene A.; Nowak, Martin A.

    2010-01-01

    Template-directed polymerization of nucleotides is believed to be a pathway for the replication of genetic material in the earliest cells. We assume that activated monomers are produced by prebiotic chemistry. These monomers can undergo spontaneous polymerization, a system that we call “prelife.” Adding template-directed polymerization changes the equilibrium structure of prelife if the rate constants meet certain criteria. In particular, if the basic reproductive ratio of sequences of a certain length exceeds one, then those sequences can attain high abundance. Furthermore, if many sequences replicate, then the longest sequences can reach high abundance even if the basic reproductive ratios of all sequences are less than one. We call this phenomenon “subcritical life.” Subcritical life suggests that sequences long enough to be ribozymes can become abundant even if replication is relatively inefficient. Our work on the evolution of replication has interesting parallels to infection dynamics. Life (replication) can be seen as an infection of prelife. PMID:20034501

  2. Parasite Stress Predicts Offspring Sex Ratio

    PubMed Central

    Dama, Madhukar Shivajirao

    2012-01-01

    In this study, I predict that the global variation of offspring sex ratio might be influenced in part by the level of parasite stress. From an energetic standpoint, higher gestational costs of producing a male offspring could decrease male births in a population with limited resources. This implies that, any factor that limits the parental resources could be expected to favor female offspring production. Human sex ratio at birth (SRB) is believed to be influenced by numerous socioeconomic, biological, and environmental factors. Here, I test a prediction that parasite stress, by virtue of its effects on the general health condition, may limit the parental investment ability and therefore could influence the SRB at the population level. The statistical analysis supports this prediction, and show that the level of parasite stress has a significant inverse relation with population SRB across the world. Further, this relation is many-folds stronger than the association of SRB with other factors, like; polygyny, fertility, latitude, and son-preference. Hence, I propose that condition affecting ability of parasites (but not adaptive significance) could be a likely causal basis for the striking variation of SRB across populations. PMID:23049967

  3. Measure your septa release ratios: pheromone release ratio variability affected by rubber septa and solvent.

    PubMed

    Kuenen, L P S; Siegel, Joel P

    2015-03-01

    The type of solvent and the volume used to load pheromone components onto rubber septa had significant effects on pheromone release ratios, the variability of those release ratios, and the recoverability of the volatile components during subsequent extraction with hexane. Volatile release ratios of synthetic Oriental fruit moth (OFM) pheromone and additional volatile compounds were determined using a gas chromatograph column as a volatile trap for rapid (≤1 hr) analysis from individual rubber septa. Volatile compound solutions were prepared in hexane, pentane, CH2Cl2, and methyl tert-butyl ether, and a 10, 33, or 100 μl aliquot of each solution was applied to rubber septa. Septa loaded with 100 μl of CH2Cl2 emitted significantly (P < 0.05) higher alcohol: acetate (OH:Ac) ratios than septa loaded with the other solvents, which were all similar. Release ratios of the alcohol and acetate components of the OFM pheromone components were assessed over a 3 week period using septa loaded with each solvent. Regardless of loading solvent, the OFM OH:Ac ratios declined logarithmically over 3 weeks; however, the decay slope from septa loaded with CH2Cl2 solutions was different from those of the other three solvents, which were nearly all the same. A high variability in OH:Ac release ratios was measured overall, regardless of the solvent used or the volume it was applied in. Four compounds of near-equal mass: 1-dodecanol, 1-dodecanal, methyl decanoate, and tridecane emitted different release ratios dependent on the solvent, hexane or CH2Cl2, with which a septum was loaded. The more polar and the greater the mass of the test compound, the slower it was emitted from a septum regardless of solvent. These combined results plus comparisons to earlier reports, suggest that researchers should empirically assess the release ratios from septa to be used in bioassays rather than just reporting the type of septum, ratios of compounds applied and solvent used to prepare them.

  4. Winglets on low aspect ratio wings

    NASA Technical Reports Server (NTRS)

    Kuhlman, John M.; Liaw, Paul

    1987-01-01

    The drag reduction potentially available from the use of winglets at the tips of low aspect ratio (1.75-2.67) wings with pronounced (45-60 deg) leading edge sweep is assessed numerically for the case of a cruise design point at Mach of 0.8 and a lift coefficient of 0.3. Both wing-winglet and wing-alone design geometries are derived from a linear-theory, minimum induced drag design methodology. Relative performance is evaluated with a nonlinear extended small disturbance potential flow analysis code. Predicted lift coefficient/pressure drag coefficient increases at equal lift for the wing-winglet configurations over the wing-alone planform are of the order of 14.6-15.8, when boundary layer interaction is included.

  5. Decay branching ratios of excited 24Mg

    NASA Astrophysics Data System (ADS)

    Munson, J. M.; Norman, E. B.; Burke, J. T.; Casperson, R. J.; Phair, L. W.; McCleskey, E.; McCleskey, M.; Lee, D.; Hughes, R. O.; Ota, S.; Czeszumska, A.; Chodash, P. A.; Saastamoinen, A. J.; Austin, R. A. E.; Spiridon, A. E.; Dag, M.; Chyzh, R.; Basunia, M. S.; Ressler, J. J.; Ross, T. J.

    2017-01-01

    The nuclear reactions 12C(12C,α )20Ne , 12C(12C,p )23Na , and 12C(12C,n )23Mg are the primary reactions in carbon burning, which occurs as part of several stellar processes. The Gamow window, which describes the energy range where most of these reactions take place, is typically around 1.5 MeV in the center-of-mass frame. Direct measurements of the cross sections at this energy are difficult due to the large Coulomb barrier present between the carbon nuclei; however, a successful surrogate measurement can provide the branching ratios between these reactions while avoiding the 12C+12C Coulomb barrier. An experiment was performed using inelastic scattering of 40 MeV α particles on 24Mg as a possible surrogate for the 12C+12C compound nucleus.

  6. Root : shoot ratios, optimization and nitrogen productivity.

    PubMed

    Agren, Göran I; Franklin, Oskar

    2003-12-01

    Plants respond to nitrogen availability by changing their root : shoot ratios. One hypothesis used to explain this allocation is that plants optimize their behaviour by maximizing their relative growth rate. The consequences of this hypothesis were investigated by formulating two models for root : shoot allocation, with and without explicit inclusion of maintenance respiration. The models also took into account that relative growth rate is a linear function of plant nitrogen concentration. The model without respiration gave qualitatively reasonable results when predictions were compared with observed results from growth experiments with birch and tomato. The explicit inclusion of maintenance respiration improved considerably the agreement between prediction and observation, and for birch was within the experimental accuracy. Further improvements will require additional details in the description of respiratory processes and the nitrogen uptake function. Plants growing under extreme nutrient stress may also optimize their behaviour with respect to other variables in addition to relative growth rate.

  7. Isotopic ratio measurements with ICP-MS

    SciTech Connect

    Russ, G.P. III; Bazan, J.M.

    1986-06-03

    An inductively-coupled-plasma source mass spectrometer (ICP-MS) has been used to measure the isotopic composition of U, Pb, Os, and B standards. Particular emphasis has been placed on uranium because of its nuclear and environmental interest and because of the availability of a well-characterized set of standards with a wide range of isotopic compositions. The precision and accuracy obtainable in isotope ratio measurements by ICP-MS depend on many factors including background, interferences, dead time, mass fractionation (bias), abundance sensitivity, and counting statistics. Which, if any, of these factors controls accuracy and precision depends on the type of sample being analyzed and the characteristics of the mass spectrometer. These issues are discussed in detail.

  8. Laser spectroscopic measurement of helium isotope ratios.

    SciTech Connect

    Wang, L.-B.; Mueller, P.; Holt, R. J.; Lu, Z.-T.; O'Connor, T. P.; Sano, Y.; Sturchio, N.; Univ. of Illinois; Univ. of Tokyo; Univ. of Illinois at Chicago

    2003-06-13

    A sensitive laser spectroscopic method has been applied to the quantitative determination of the isotope ratio of helium at the level of {sup 3}He/{sup 4}He = 10{sup -7}--10{sup -5}. The resonant absorption of 1083 nm laser light by the metastable {sup 3}He atoms in a discharge cell was measured with the frequency modulation saturation spectroscopy technique while the abundance of {sup 4}He was measured by a direct absorption technique. The results on three different samples extracted from the atmosphere and commercial helium gas were in good agreement with values obtained with mass spectrometry. The achieved 3{sigma} detection limit of {sup 3}He in helium is 4 x 10{sup -9}. This demonstration required a 200 {mu}L STP sample of He. The sensitivity can be further improved, and the required sample size reduced, by several orders of magnitude with the addition of cavity enhanced spectroscopy.

  9. Increased testosterone to cortisol ratio in psychopathy

    PubMed Central

    Glenn, Andrea L.; Raine, Adrian; Schug, Robert A.; Gao, Yu; Granger, Douglas A.

    2011-01-01

    Only a few studies have examined hormones in psychopathy and results have been mixed. It has been suggested that since hormone systems are highly interconnected, it may be important to examine multiple systems simultaneously to gain a clearer picture of how hormones work together to predispose for a certain construct. In the present study, we attempt to clarify the role of the hormones cortisol and testosterone in psychopathy by examining both hormones in a community sample of 178 adults demonstrating a wide range of psychopathy scores. Results showed that psychopathy scores were associated with an increased ratio of testosterone (baseline) to cortisol responsivity to a stressor. Psychopathy was not associated with either of these measures independently, or with baseline cortisol levels. These findings suggest that these highly interconnected hormone systems may work in concert to predispose to psychopathy. PMID:21133509

  10. Golden ratio prediction for solar neutrino mixing

    SciTech Connect

    Kajiyama, Yuji; Raidal, Martti; Strumia, Alessandro

    2007-12-01

    We present a simple texture that predicts the cotangent of the solar neutrino mixing angle to be equal to the golden ratio. This prediction is 1.4{sigma} below the present best-fit value and final SNO and KamLAND data could discriminate it from tri-bimaximal mixing. The neutrino mass matrix is invariant under a Z{sub 2} x Z{sub 2}{sup '} symmetry: that geometrically is a reflection along the diagonal of the golden rectangle. Assuming an analogous structure in the quark sector suggests a golden prediction for the Cabibbo angle, {theta}{sub C}={pi}/4-{theta}{sub 12}{approx_equal}13.3 deg., up to the uncertainties comparable to V{sub ub}.

  11. Verification of the surrogate ratio method

    SciTech Connect

    Chiba, Satoshi; Iwamoto, Osamu

    2010-04-15

    Effects of difference in the spin and parity distributions for the surrogate and neutron-induced reactions are investigated. Without assuming specific (schematic) spin-parity distributions, it was found that the surrogate ratio method can be employed to determine neutron fission and capture cross sections if (1) weak Weisskopf-Ewing condition (defined in this paper) is satisfied, (2) there exist two surrogate reactions whose spin-parity distributions of the decaying nuclei are almost equivalent, and (3) difference of the representative spin values between the neutron-induced and surrogate reactions is no much larger than 10(Planck constant/2pi). If these conditions are satisfied, we need not know the spin-parity distributions populated by the surrogate method. Instead, we should just select a pair of surrogate reactions which will populate the similar spin-parity distributions, using targets having similar structure and reactions having the similar reaction mechanisms. Achievable accuracy is estimated to be around 5% and 10% for fission and capture channels, respectively, for nuclei of the Uranium region. The surrogate absolute method may be applicable to determination of fission cross sections with a caution. However, there will be little hope to apply this method for capture cross section measurements unless the spin-parity distributions in the neutron-induced and surrogate reactions are fairly close to each other (which is implausible) or the difference can be corrected theoretically. The surrogate ratio method was shown also to be a robust method in the presence of breakup reactions without assuming specific breakup reaction mechanisms.

  12. Hardness ratios of different neutron spectra.

    PubMed

    Tommasino, L; Tripathy, S P

    2004-01-01

    Extensive data have been gathered in the past on the response of different detectors, based on the registration of neutron-induced fissions in bismuth, gold, tantalum and thorium by the spark-replica counter and the thin film breakdown counter. These detectors make it possible to exploit the excellent characteristics of the fission reactions for the measurements of high-energy neutrons. Most of the investigations have been carried out at the quasi-monoenergetic neutron beam facility at The Svedberg Laboratory-TSL of the Uppsala University in cooperation with the Khlopin Radium Institute (KRI). The responses of different fission detectors in the neutron energy range 35-180 MeV have been evaluated: a region where the predictive power of available nuclear reaction models and codes is not reliable yet. For neutron energy >200 MeV, the fission-detector responses have been derived from the data of the proton fission cross sections. By using the ratio of the responses of these detectors, a simple and accurate way to evaluate the spectrum hardness can be obtained, thus providing a tool to obtain spectral information needed for neutron dosimetry without the need to know the entire spectrum. Extensive data have been already obtained for the high-energy neutron spectrum from the CERN concrete facility. In the present paper, the measured values of the response ratios for different fissile detectors exposed at the CERN facility are compared with those calculated for the spectra from the same facility and from different altitudes in the atmosphere, respectively.

  13. Classification of particle effective shape ratios in cirrus clouds based on the lidar depolarization ratio.

    PubMed

    Noel, Vincent; Chepfer, Helene; Ledanois, Guy; Delaval, Arnaud; Flamant, Pierre H

    2002-07-20

    A shape classification technique for cirrus clouds that could be applied to future spaceborne lidars is presented. A ray-tracing code has been developed to simulate backscattered and depolarized lidar signals from cirrus clouds made of hexagonal-based crystals with various compositions and optical depth, taking into account multiple scattering. This code was used first to study the sensitivity of the linear depolarization rate to cloud optical and microphysical properties, then to classify particle shapes in cirrus clouds based on depolarization ratio measurements. As an example this technique has been applied to lidar measurements from 15 mid-latitude cirrus cloud cases taken in Palaiseau, France. Results show a majority of near-unity shape ratios as well as a strong correlation between shape ratios and temperature: The lowest temperatures lead to high shape ratios. The application of this technique to space-borne measurements would allow a large-scale classification of shape ratios in cirrus clouds, leading to better knowledge of the vertical variability of shapes, their dependence on temperature, and the formation processes of clouds.

  14. Estimation of Se(VI)/Se(IV) ratio in water by the ratio recorded in barite

    NASA Astrophysics Data System (ADS)

    Tokunaga, Kohei; Yokoyama, Yuka; Takahashi, Yoshio

    2013-11-01

    It is possible that the distribution behaviors of redox-sensitive elements such as selenium (Se) between authigenic minerals and water can provide information on the oxidation state of the element in the coexistent water during mineral deposition. Considering the similar chemical characteristics of Se(IV) and Se(VI) oxyanions, we propose that the Se(VI)/Se(IV) ratio in a particular precipitate, such as barite, may enable us to estimate the Se(VI)/Se(IV) ratio in the coexistent water. The coprecipitation experiments of Se with barite coupled with the determination of the oxidation state of Se both in the aqueous phase and in barite were conducted by Se K-edge X-ray absorption near-edge structure and high-performance liquid chromatography connected to inductively coupled plasma-mass spectrometry, respectively, to investigate the influence of the oxidation state of Se on its immobilization into barite at pH 4.0 and 8.0. The results showed that the Se(VI)/Se(IV) ratio in barite was correlated with the Se(VI)/Se(IV) ratio in water, which in turn can provide physicochemical and biogeochemical information related to the Se(VI)/Se(IV) ratio in water in the environment where barite precipitated.

  15. Predictive Value of Neutrophil Lymphocyte Ratio and Platelet Lymphocyte Ratio in Patients with Coronary Slow Flow

    PubMed Central

    Çetin, Mustafa; Kiziltunc, Emrullah; Elalmış, Özgül Uçar; Çetin, Zehra Güven; Demirçelik, Muhammed Bora; Çiçekçioğlu, Hülya; Kurtul, Alparslan; Özkan, Selçuk; Avan, Candan Mansuroğlu; Örnek, Ender; Ulusoy, Feridun Vasfi

    2016-01-01

    Background Increased microvascular resistance due to chronic inflammation is assumed to be one of the mechanisms associated with coronary slow flow (CSF). Previous studies have shown that the platelet-to-lymphocyte ratio (PLR) and the neutrophil-lymphocyte ratio (NLR) are markers of inflammation for various diseases. In this study we aimed to evaluate the relationship between CSF and PLR-NLR. Methods Seventy-eight patients with CSF and 50 patients with normal coronary flow were enrolled into this study. The study subjects underwent medical examination and testing, after which their platelet-to-lymphocyte ratios and NLR values were calculated. An independent observer measured the coronary flow rate by Thrombolysis in Myocardial Infarction Frame Count (TFC) method. The platelet-to-lymphocyte ratio and NLR values were compared between the groups and correlation analysis was performed to explore the relationship between mean TFC with PLR and NLR. Results Platelet-to-lymphocyte ratio and NLR values were significantly higher in patients with CSF (p < 0.001). There was a positive significant correlation between TFC with NLR and PLR (Spearman’s Rho: 0.59, p < 0.001 and Spearman’s Rho: 0.30, p = 0.001, respectively). Multivariate logistic regression analysis revealed that NLR is the one independent predictor for CSF. Conclusions This study demonstrated an association between CSF and PLR-NLR. Although the exact mechanism could not be explained, our findings support the possible role of inflammation in CSF physiopathology. PMID:27274171

  16. Effects of a Signaled Delay to Reinforcement in the Previous and Upcoming Ratios on Between-Ratio Pausing in Fixed-Ratio Schedules

    ERIC Educational Resources Information Center

    Harris, Aimee; Foster, T. Mary; Levine, Joshua; Temple, William

    2012-01-01

    Domestic hens responded under multiple fixed-ratio fixed-ratio schedules with equal fixed ratios. One component provided immediate reinforcement and the other provided reinforcement after a delay, signaled by the offset of the key light. The components were presented quasi-randomly so that all four possible transitions occurred in each session.…

  17. Cereal Production Ratio and NDVI in Spain

    NASA Astrophysics Data System (ADS)

    Saa-Requejo, Antonio; Recuero, Laura; Palacios, Alicia; Díaz-Ambrona, Carlos G. H.; Tarquis, Ana M.

    2014-05-01

    Droughts are long-term phenomena affecting large regions causing significant damages both in human lives and economic losses. The use of remote sensing has proved to be very important in monitoring the growth of agricultural crops and trying to asses weather impact on crop loss. Several indices has been developed based in remote sensing data being one of them the normalized difference vegetation index (NDVI). In this study we have focus to know the correlation between NDVI data and the looses of rain fed cereal in the Spanish area where this crop is majority. For this propose data from drought damage in cereal come from the pool of agricultural insurance in Spain (AGROSEGURO) including 2007/2008 to 2011/2012 (five agricultural campaigns). This data is given as a ratio between drought party claims against the insured value of production aggregated at the agrarian region level. Medium resolution (500x500 m2) MODIS images were used during the same campaigns to estimate the eight-day composites NDVI at these locations. The NDVI values are accumulated following the normal cycle of the cereal taking in account the sowing date at different sites. At the same time, CORINE Land Cover (2006) was used to classify the pixels belonging to rain fed cereal use including a set of conditions such as pixels showing dry during summer, area in which there has been no change of use. Fallow presence is studied with particular attention as it imposes an inter annual variation between crop and bare soil and causes decreases in greenness in a pixel and mix both situations. This is more complex in the situation in which the avoid fallow and a continuous monoculture is performed. The results shown that around 40% of the area is subject to the regime of fallow while 60% have growing every year. In addition, another variation is detected if the year is humid (decrease of fallow) or dry (increase of fallow). The level of correlation between the drought damage ratios and cumulative NDVI for the

  18. 42 CFR 403.256 - Loss ratio supporting data.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 42 Public Health 2 2010-10-01 2010-10-01 false Loss ratio supporting data. 403.256 Section 403.256... Ratio Provisions § 403.256 Loss ratio supporting data. (a) For purposes of requesting CMS certification under § 403.232, the insuring organization must submit the following loss ratio data to CMS for...

  19. 10 CFR 436.21 - Savings-to-investment ratio.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 10 Energy 3 2012-01-01 2012-01-01 false Savings-to-investment ratio. 436.21 Section 436.21 Energy... Procedures for Life Cycle Cost Analyses § 436.21 Savings-to-investment ratio. The savings-to-investment ratio is the ratio of the present value savings to the present value costs of an energy or...

  20. 12 CFR 615.5335 - Bank net collateral ratio.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Bank net collateral ratio. 615.5335 Section 615... collateral ratio. (a) Each bank shall achieve and at all times maintain a net collateral ratio of at least 103 percent. (b) At a minimum, a bank shall compute its net collateral ratio as of the end of...

  1. 12 CFR 615.5206 - Permanent capital ratio computation.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 12 Banks and Banking 6 2011-01-01 2011-01-01 false Permanent capital ratio computation. 615.5206... capital ratio computation. (a) The institution's permanent capital ratio is determined on the basis of the... average daily balances for the most recent 3 months. (c) The institution's permanent capital ratio...

  2. 12 CFR 615.5206 - Permanent capital ratio computation.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 12 Banks and Banking 7 2013-01-01 2013-01-01 false Permanent capital ratio computation. 615.5206... capital ratio computation. (a) The institution's permanent capital ratio is determined on the basis of the... average daily balances for the most recent 3 months. (c) The institution's permanent capital ratio...

  3. 26 CFR 26.2642-5 - Finality of inclusion ratio.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 26 Internal Revenue 14 2014-04-01 2013-04-01 true Finality of inclusion ratio. 26.2642-5 Section...-5 Finality of inclusion ratio. (a) Direct skips. The inclusion ratio applicable to a direct skip...) Other GSTs. With respect to taxable distributions and taxable terminations, the inclusion ratio for...

  4. 26 CFR 26.2642-5 - Finality of inclusion ratio.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 26 Internal Revenue 14 2013-04-01 2013-04-01 false Finality of inclusion ratio. 26.2642-5 Section...-5 Finality of inclusion ratio. (a) Direct skips. The inclusion ratio applicable to a direct skip...) Other GSTs. With respect to taxable distributions and taxable terminations, the inclusion ratio for...

  5. 42 CFR 403.256 - Loss ratio supporting data.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 42 Public Health 2 2011-10-01 2011-10-01 false Loss ratio supporting data. 403.256 Section 403.256... Ratio Provisions § 403.256 Loss ratio supporting data. (a) For purposes of requesting CMS certification under § 403.232, the insuring organization must submit the following loss ratio data to CMS for...

  6. 12 CFR 615.5330 - Minimum surplus ratios.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 12 Banks and Banking 7 2012-01-01 2012-01-01 false Minimum surplus ratios. 615.5330 Section 615... surplus ratios. (a) Total surplus. (1) Each institution shall achieve and at all times maintain a ratio of... institution shall achieve and at all times maintain a ratio of core surplus to the risk-adjusted asset base...

  7. 12 CFR 615.5206 - Permanent capital ratio computation.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Permanent capital ratio computation. 615.5206... capital ratio computation. (a) The institution's permanent capital ratio is determined on the basis of the... average daily balances for the most recent 3 months. (c) The institution's permanent capital ratio...

  8. 12 CFR 615.5335 - Bank net collateral ratio.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 12 Banks and Banking 6 2011-01-01 2011-01-01 false Bank net collateral ratio. 615.5335 Section 615... collateral ratio. (a) Each bank shall achieve and at all times maintain a net collateral ratio of at least 103 percent. (b) At a minimum, a bank shall compute its net collateral ratio as of the end of...

  9. 12 CFR 615.5206 - Permanent capital ratio computation.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 12 Banks and Banking 7 2012-01-01 2012-01-01 false Permanent capital ratio computation. 615.5206... capital ratio computation. (a) The institution's permanent capital ratio is determined on the basis of the... average daily balances for the most recent 3 months. (c) The institution's permanent capital ratio...

  10. 26 CFR 26.2642-5 - Finality of inclusion ratio.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 26 Internal Revenue 14 2012-04-01 2012-04-01 false Finality of inclusion ratio. 26.2642-5 Section...-5 Finality of inclusion ratio. (a) Direct skips. The inclusion ratio applicable to a direct skip...) Other GSTs. With respect to taxable distributions and taxable terminations, the inclusion ratio for...

  11. 42 CFR 403.256 - Loss ratio supporting data.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 42 Public Health 2 2012-10-01 2012-10-01 false Loss ratio supporting data. 403.256 Section 403.256... Ratio Provisions § 403.256 Loss ratio supporting data. (a) For purposes of requesting CMS certification under § 403.232, the insuring organization must submit the following loss ratio data to CMS for...

  12. 12 CFR 615.5335 - Bank net collateral ratio.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 12 Banks and Banking 7 2013-01-01 2013-01-01 false Bank net collateral ratio. 615.5335 Section 615... collateral ratio. (a) Each bank shall achieve and at all times maintain a net collateral ratio of at least 103 percent. (b) At a minimum, a bank shall compute its net collateral ratio as of the end of...

  13. 12 CFR 615.5330 - Minimum surplus ratios.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 12 Banks and Banking 6 2010-01-01 2010-01-01 false Minimum surplus ratios. 615.5330 Section 615... surplus ratios. (a) Total surplus. (1) Each institution shall achieve and at all times maintain a ratio of... institution shall achieve and at all times maintain a ratio of core surplus to the risk-adjusted asset base...

  14. 12 CFR 615.5335 - Bank net collateral ratio.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 12 Banks and Banking 7 2014-01-01 2014-01-01 false Bank net collateral ratio. 615.5335 Section 615... collateral ratio. (a) Each bank shall achieve and at all times maintain a net collateral ratio of at least 103 percent. (b) At a minimum, a bank shall compute its net collateral ratio as of the end of...

  15. 42 CFR 423.2420 - Calculation of medical loss ratio.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 42 Public Health 3 2014-10-01 2014-10-01 false Calculation of medical loss ratio. 423.2420 Section... for a Minimum Medical Loss Ratio § 423.2420 Calculation of medical loss ratio. (a) Determination of the MLR. (1) The MLR for each contract under this part is the ratio of the numerator (as defined...

  16. 12 CFR 615.5330 - Minimum surplus ratios.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 12 Banks and Banking 6 2011-01-01 2011-01-01 false Minimum surplus ratios. 615.5330 Section 615... surplus ratios. (a) Total surplus. (1) Each institution shall achieve and at all times maintain a ratio of... institution shall achieve and at all times maintain a ratio of core surplus to the risk-adjusted asset base...

  17. 42 CFR 403.256 - Loss ratio supporting data.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 42 Public Health 2 2014-10-01 2014-10-01 false Loss ratio supporting data. 403.256 Section 403.256... Ratio Provisions § 403.256 Loss ratio supporting data. (a) For purposes of requesting CMS certification under § 403.232, the insuring organization must submit the following loss ratio data to CMS for...

  18. 10 CFR 436.21 - Savings-to-investment ratio.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 10 Energy 3 2014-01-01 2014-01-01 false Savings-to-investment ratio. 436.21 Section 436.21 Energy... Procedures for Life Cycle Cost Analyses § 436.21 Savings-to-investment ratio. The savings-to-investment ratio is the ratio of the present value savings to the present value costs of an energy or...

  19. 12 CFR 615.5330 - Minimum surplus ratios.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 12 Banks and Banking 7 2014-01-01 2014-01-01 false Minimum surplus ratios. 615.5330 Section 615... surplus ratios. (a) Total surplus. (1) Each institution shall achieve and at all times maintain a ratio of... institution shall achieve and at all times maintain a ratio of core surplus to the risk-adjusted asset base...

  20. 26 CFR 26.2642-5 - Finality of inclusion ratio.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 26 Internal Revenue 14 2011-04-01 2010-04-01 true Finality of inclusion ratio. 26.2642-5 Section...-5 Finality of inclusion ratio. (a) Direct skips. The inclusion ratio applicable to a direct skip...) Other GSTs. With respect to taxable distributions and taxable terminations, the inclusion ratio for...

  1. 42 CFR 403.256 - Loss ratio supporting data.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 42 Public Health 2 2013-10-01 2013-10-01 false Loss ratio supporting data. 403.256 Section 403.256... Ratio Provisions § 403.256 Loss ratio supporting data. (a) For purposes of requesting CMS certification under § 403.232, the insuring organization must submit the following loss ratio data to CMS for...

  2. 12 CFR 615.5335 - Bank net collateral ratio.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 12 Banks and Banking 7 2012-01-01 2012-01-01 false Bank net collateral ratio. 615.5335 Section 615... collateral ratio. (a) Each bank shall achieve and at all times maintain a net collateral ratio of at least 103 percent. (b) At a minimum, a bank shall compute its net collateral ratio as of the end of...

  3. 12 CFR 615.5206 - Permanent capital ratio computation.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 12 Banks and Banking 7 2014-01-01 2014-01-01 false Permanent capital ratio computation. 615.5206... capital ratio computation. (a) The institution's permanent capital ratio is determined on the basis of the... average daily balances for the most recent 3 months. (c) The institution's permanent capital ratio...

  4. 12 CFR 615.5330 - Minimum surplus ratios.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 12 Banks and Banking 7 2013-01-01 2013-01-01 false Minimum surplus ratios. 615.5330 Section 615... surplus ratios. (a) Total surplus. (1) Each institution shall achieve and at all times maintain a ratio of... institution shall achieve and at all times maintain a ratio of core surplus to the risk-adjusted asset base...

  5. 10 CFR 436.21 - Savings-to-investment ratio.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... Procedures for Life Cycle Cost Analyses § 436.21 Savings-to-investment ratio. The savings-to-investment ratio is the ratio of the present value savings to the present value costs of an energy or water conservation measure. The numerator of the ratio is the present value of net savings in energy or water and...

  6. 10 CFR 436.21 - Savings-to-investment ratio.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Procedures for Life Cycle Cost Analyses § 436.21 Savings-to-investment ratio. The savings-to-investment ratio is the ratio of the present value savings to the present value costs of an energy or water conservation measure. The numerator of the ratio is the present value of net savings in energy or water and...

  7. Low concentration ratio solar array structural configuration

    NASA Technical Reports Server (NTRS)

    Nalbandian, S. J.

    1984-01-01

    The design and structural properties of a low concentration ratio solar array are discussed. The assembled module consists of six interconnected containers which are compactly stowed in a volume of 3.24 m(3) for delivery to orbit by the shuttle. The containers deploy in accordian fashion into a rectangular area of 19.4 x 68 meters and can be attached to the user spacecraft along the longitudinal centerline of the end container housing. Five rotary incremental actuators requiring about 8 watts each will execute the 180-degree rotation at each joint. Deployable masts (three per side) are used to extend endcaps from the housing in both directions. Each direction is extended by three masts requiring about 780 watts for about 27 minutes. Concentrator elements are extended by the endcaps and are supported by cable systems that are connected between the housings and endcaps. These power generating elements contain reflector panels which concentrate light onto the solar panels consisting of an aluminum radiator with solar cells positioned within the element base formed by the reflectors. A flat wire harness collects the power output of individual elements for transfer to the module container housing harnesses.

  8. Fuel-air ratio controlled carburetion system

    SciTech Connect

    Abbey, H. G.

    1980-02-12

    An automatic control system is disclosed supplying a fuel-air mixture to an internal combustion engine including a variable-venturi carburetor. Air is fed into the input of the venturi, the air passing through the throat thereof whose effective area is adjusted by a mechanism operated by a servo motor. Fuel is fed into the input of the venturi from a fuel reservoir through a main path having a fixed orifice and an auxiliary path formed by a metering valve operated by an auxiliary fuel-control motor. The differential air pressure developed between the inlet of the venturi and the throat thereof is sensed to produce an airvelocity command signal that is applied to a controller adapted to compare the command signal with the servo motor set point to produce an output for governing the servo motor to cause it to seek a null point, thereby defining a closed process control loop. The intake manifold vacuum, which varies in degree as a function of load and speed conditions is sensed to govern the auxiliary fuel-control motor accordingly, is at the same time converted into an auxiliary signal which is applied to the controller in the closed loop to modulate the command signal in a manner establishing an optimum air-fuel ratio under the varying conditions of load and speed.

  9. Zenith polarization and color ratio during twilight.

    PubMed

    Volz, F E

    1981-12-15

    The excellent data of zenith polarization and color ratio (CR) during twilight obtained by Coulson at the Mauna Loa Observatory, Hawaii are subjected to a reinterpretation, especially with regard to the frequent deviations from the clear average. It is shown that a moderate lift of the earth's shadow by distant clouds (or by low level haze) will reduce the red/green CR, while greater lift shifts the CR peak to a smaller solar depression. The effect on zenith polarization at wavelengths >/=0.6 microm is seen to correspond to a slight reduction of overall polarization for a moderate lift, and for a large lift to a shift of the polarization minimum (depolarization by stratospheric aerosol) from 4 degrees solar depression angle to 2 degrees . A generally high level of polarization, but with a barely noticeable 4 degrees minimum, had also been observed earlier in Germany by Steinhorst when the stratospheric aerosol load was very small. The difference is explained by a higher and stronger aerosol layer in the tropics combined with a higher and cleaner troposphere.

  10. New High Aspect-Ratio Titania Nanotubes

    NASA Astrophysics Data System (ADS)

    Panaitescu, Eugen; Richter, Christiaan; Menon, Latika

    2007-03-01

    Titanium oxide nanotubes show great promise in photocatalytic, gas sensing, biological, and other applications. Techniques for the fabrication of titania nanotubes include electrodeposition in polymer molds starting from alumina templates, anodization of titanium in fluoride containing solutions, and hydrothermal treatment of nano- and micropowders. We have developed a new synthesis route for the production of new ultra-high aspect-ratio (over 1000:1) titania nanotubes by anodization in chloride containing acid solutions. The fabrication process occurs rapidly, in a fraction of the time when compared with other methods such as anodization in the highly toxic fluoride-containing electrolytes. We have demonstrated nanotubes with diameters as small as 25 nm, and lengths of up to 50 μm, and we have produced them with varying carbon content through the addition of organic acids in the electrolyte. This opens up new possibilities for many advanced applications of such nanotubes. Various synthesis conditions (pH, chloride content, electrolyte nature), and their influence on morphology, composition, and crystalline structure will be presented. Preliminary results on photocatalytic and transmission properties will also be discussed.

  11. Prioritizing Rare Variants with Conditional Likelihood Ratios

    PubMed Central

    Li, Weili; Dobbins, Sara; Tomlinson, Ian; Houlston, Richard; Pal, Deb K.; Strug, Lisa J.

    2016-01-01

    Background Prioritizing individual rare variants within associated genes or regions often consists of an ad hoc combination of statistical and biological considerations. From the statistical perspective, rare variants are often ranked using Fisher’s exact p values, which can lead to different rankings of the same set of variants depending on whether 1- or 2-sided p values are used. Results We propose a likelihood ratio-based measure, maxLRc, for the statistical component of ranking rare variants under a case-control study design that avoids the hypothesis-testing paradigm. We prove analytically that the maxLRc is always well-defined, even when the data has zero cell counts in the 2×2 disease-variant table. Via simulation, we show that the maxLRc outperforms Fisher’s exact p values in most practical scenarios considered. Using next-generation sequence data from 27 rolandic epilepsy cases and 200 controls in a region previously shown to be linked to and associated with rolandic epilepsy, we demonstrate that rankings assigned by the maxLRc and exact p values can differ substantially. Conclusion The maxLRc provides reliable statistical prioritization of rare variants using only the observed data, avoiding the need to specify parameters associated with hypothesis testing that can result in ranking discrepancies across p value procedures; and it is applicable to common variant prioritization. PMID:25659987

  12. Quantification of neocortical ratios in stem primates.

    PubMed

    Long, Adam; Bloch, Jonathan I; Silcox, Mary T

    2015-07-01

    Extant euprimates (=crown primates) have a characteristically expanded neocortical region of the brain relative to that of other mammals, but the timing of that expansion in their evolutionary history is poorly resolved. Examination of anatomical landmarks on fossil endocasts of Eocene euprimates suggests that significant neocortical expansion relative to contemporaneous mammals was already underway. Here, we provide quantitative estimates of neocorticalization in stem primates (plesiadapiforms) relevant to the question of whether relative neocortical expansion was uniquely characteristic of the crown primate radiation. Ratios of neocortex to endocast surface areas were calculated for plesiadapiforms using measurements from virtual endocasts of the paromomyid Ignacius graybullianus (early Eocene, Wyoming) and the microsyopid Microsyops annectens (middle Eocene, Wyoming). These data are similar to a published estimate for the plesiadapid, Plesiadapis tricuspidens, but contrast with those calculated for early Tertiary euprimates in being within the 95% confidence intervals for archaic mammals generally. Interpretation of these values is complicated by the paucity of sampled endocasts for older stem primates and euarchontogliran outgroups, as well as by a combination of effects related to temporal trends, allometry, and taxon-unique specializations. Regardless, these results are consistent with the hypothesis that a shift in brain organization occurred in the first euprimates, likely in association with elaborations to the visual system.

  13. Intrahospital correlation of the international normalized ratio.

    PubMed

    Lazo-Langner, Alejandro; Villa-Márquez, Rosario; Hernández-Hernández, Darinel; Rojas-Maya, Sonia; Piedras, Josefa

    2009-01-01

    Background. Monitoring of oral anticoagulant therapy (OAT) is usually accomplished by measuring prothrombin time and the international normalized ratio (INR). However, thromboplastins have different responsiveness and sensitivity to vitamin K-dependent coagulation factors depletion. Several studies have shown INR variation when low sensitive thromboplastins are used. This study compared INR variability between two laboratories using highly sensitive thromboplastins. Methods. A total of 237 plasmas were tested, half of them from patients under OAT. Samples were tested simultaneously in two laboratories: in laboratory A, a Behring Coagulation Timer instrument and a human recombinant thromboplastin (Innovin, Dade Behring) (ISI 1.01) were used. In laboratory B, a Thrombolyzer Compact (Behnk Elektronik) and a rabbit brain thromboplastin (Simplastin Excel S, Organon Teknika) with an ISI of 1.30 were used. Statistical analysis was carried out according to the method of Bland and Altman. Results. Even though high correlation coefficients were obtained when comparing both laboratories, Bland-Altman analysis showed a variation of INR between laboratories ranging from -0.77 to +1.07. After logarithmic transformation of data, these values yielded a variation of the INR either 25% below or 44% above. Conclusions. These results are clearly inadequate for clinical use because such a variation would most probably induce the clinician to make a change in warfarin dose. Standardization of instruments, reagents, and controls is warranted to decrease this variation.

  14. Carbon to oxygen ratios in extrasolar planetesimals

    NASA Astrophysics Data System (ADS)

    Wilson, David J.; Gänsicke, Boris T.; Farihi, Jay; Koester, Detlev

    2016-07-01

    Observations of small extrasolar planets with a wide range of densities imply a variety of planetary compositions and structures. Currently, the only technique to measure the bulk composition of extrasolar planetary systems is the analysis of planetary debris accreting on to white dwarfs, analogous to abundance studies of meteorites. We present measurements of the carbon and oxygen abundances in the debris of planetesimals at ten white dwarfs observed with the Hubble Space Telescope, along with C/O ratios of debris in six systems with previously reported abundances. We find no evidence for carbon-rich planetesimals, with C/O < 0.8 by number in all 16 systems. Our results place an upper limit on the occurrence of carbon-rich systems at <17 per cent with a 2σ confidence level. The range of C/O of the planetesimals is consistent with that found in the Solar system, and appears to follow a bimodal distribution: a group similar to the CI chondrites, with log (< C/O >) = -0.92, and oxygen-rich objects with C/O less than or equal to that of the bulk Earth. The latter group may have a higher mass fraction of water than the Earth, increasing their relative oxygen abundance.

  15. Effects of Ratio Strategies Intervention on Knowledge of Ratio Equivalence for Students with Learning Disability

    ERIC Educational Resources Information Center

    Hunt, Jessica H.; Vasquez, Eleazar, III

    2014-01-01

    Students with mathematics learning disabilities have a weak understanding of mathematical concepts that underlie success in Algebra I, such as ratios and proportional reasoning. In this study, researchers used a multiple baseline across participants design to evaluate the effects of a intervention based on a instructional trajectory of how…

  16. Mixing properties of coaxial jets with large velocity ratios and large inverse density ratios

    NASA Astrophysics Data System (ADS)

    Alexander Schumaker, S.; Driscoll, James F.

    2012-05-01

    An experimental study was conducted to better understand the mixing properties of coaxial jets as several parameters were systematically varied, including the velocity ratio, density ratio, and the Reynolds number. Diameters of the inner and outer jet were also varied. Coaxial jets are commonly used to mix fluids due to the simplicity of their geometry and the rapid mixing that they provide. A measure of the overall mixing efficiency is the stoichiometric mixing length (Ls), which is the distance along the jet centerline where the two fluids have mixed to some desired concentration, which was selected to be the stoichiometric concentration for H2/O2 and CH4/O2 in this case. For 56 cases, the profiles of mean mixture fraction, rms mixture fraction fluctuations (unmixedness), and Ls were measured using acetone planar laser induced fluorescence diagnostics. Results were compared to three mixing models. The entrainment model of Villermaux and Rehab showed good agreement with the data, indicating that the proper non-dimensional scaling parameter is the momentum flux ratio M. The work extends the existing database of coaxial jet scalar mixing properties because it considers the specific regime of large values of both the velocity ratio and the inverse density ratio, which is the regime in which rocket injectors operate. Also the work focuses on the mixing up to Ls where previous work focused on the mixing up to the end of the inner core. The Reynolds numbers achieved for a number of cases were considerably larger than previous gas mixing studies, which insures that the jet exit boundary conditions are fully turbulent.

  17. Oxidative ratio (OR) of UK peats

    NASA Astrophysics Data System (ADS)

    Clay, G. D.; Worrall, F.; Masiello, C. A.

    2012-04-01

    The oxidative ratio (OR) is the amount of CO2 sequestered in the terrestrial biosphere for each mol of O2 produced. The OR governs the effectiveness of a terrestrial biome to mitigate the impact of anthropogenic CO2 emissions and it has been used to calculate the balance of terrestrial and oceanic carbon sinks across the globe. However, few studies have investigated the controls of the variability in OR. What factors affect OR - climate? Soil type? Vegetation type? N deposition? Land use? Land use change? Small shifts in OR could have important implications in the global partitioning of CO2 between the atmosphere, biosphere, and oceans. This study looks at peat soils (Histosols) from a series of sites representing a climatic transect across the UK. Duplicate peat cores were taken, along with samples of above-ground vegetation and litter, from sites in northern Scotland (Forsinard), southern Scotland (Auchencorth), northern England (Moor House; Thorne Moor) through the Welsh borders (Whixhall Moss) and Somerset levels (Westhay Moor) to Dartmoor and Bodmin Moor in the south west of England. Sub-samples of the cores were analysed for their CHNO concentrations using a Costech ECS 4010 Elemental combustion system. Using the method of Masiello et al. (2008), OR values could be calculated from these elemental concentrations. Initial results show that OR values of UK peats varied between 0.94 and 1.1 with a median value of 1.05 which similar to the median value of World soils but the range is at the more reduced end. There was significant variation between peat cores, even between peat cores on the same site and the peat showed significant reduction in OR with depth in the core.

  18. Numerical Estimation of the Spent Fuel Ratio

    SciTech Connect

    Lindgren, Eric R.; Durbin, Samuel; Wilke, Jason; Margraf, J.; Dunn, T. A.

    2016-01-01

    Sabotage of spent nuclear fuel casks remains a concern nearly forty years after attacks against shipment casks were first analyzed and has a renewed relevance in the post-9/11 environment. A limited number of full-scale tests and supporting efforts using surrogate materials, typically depleted uranium dioxide (DUO 2 ), have been conducted in the interim to more definitively determine the source term from these postulated events. However, the validity of these large- scale results remain in question due to the lack of a defensible spent fuel ratio (SFR), defined as the amount of respirable aerosol generated by an attack on a mass of spent fuel compared to that of an otherwise identical surrogate. Previous attempts to define the SFR in the 1980's have resulted in estimates ranging from 0.42 to 12 and include suboptimal experimental techniques and data comparisons. Because of the large uncertainty surrounding the SFR, estimates of releases from security-related events may be unnecessarily conservative. Credible arguments exist that the SFR does not exceed a value of unity. A defensible determination of the SFR in this lower range would greatly reduce the calculated risk associated with the transport and storage of spent nuclear fuel in dry cask systems. In the present work, the shock physics codes CTH and ALE3D were used to simulate spent nuclear fuel (SNF) and DUO 2 targets impacted by a high-velocity jet at an ambient temperature condition. These preliminary results are used to illustrate an approach to estimate the respirable release fraction for each type of material and ultimately, an estimate of the SFR. This page intentionally blank

  19. Recovery of value-added products from red mud and foundry bag-house dust

    NASA Astrophysics Data System (ADS)

    Hammond, Keegan

    "Waste is wasted if you waste it, otherwise it is a resource. Resource is wasted if you ignore it and do not conserve it with holistic best practices and reduce societal costs. Resource is for the transformation of people and society." Red mud is a worldwide problem with reserves in the hundreds of millions of tons and tens of millions of tons being added annually. Currently there is not an effective way to deal with this byproduct of the Bayer Process, the primary means of refining bauxite ore in order to provide alumina. This alumina is then treated by electrolysis using the Hall-Heroult process to produce elemental aluminum. The resulting mud is a mixture of solid and metallic oxides, and has proven to be a great disposal problem. This disposal problem is compounded by the fact that the typical bauxite processing plant produces up to three times as much red mud as alumina. Current practice of disposal is to store red mud in retention ponds until an economical fix can be discovered. The danger associated with this current method of storage is immense to the surrounding communities and environment, thus the interest from the Center for Resource Recovery and Recycling (CR3). The purpose of this document is to explain one way to remove the value added materials, primarily iron, from the Jamaican red mud using both pyrometallurgical and hydrometallurgical approaches. In the beginning, soda ash and carbon roasting were completed simultaneously at 800°C. This type of roasting produced results that were unacceptable. After the soda ash roast was completed independently of carbon roasting, a water wash produced results that separations of alumina at 90%, Iron at 99%, calcium at 99%, titanium t 100%, and sodium by 74%. Smelting produced separations of 97% for alumina, 99% for iron, 87% for sodium, 94% for calcium and 72% for titanium.

  20. Environmental Technology Verification: Baghouse Filtration Products--Sinoma Science & Technology Co. Ltd FT-806 Filtration Media

    EPA Science Inventory

    EPA created the Environmental Technology Verification (ETV) Program to facilitate the deployment of innovative or improved environmental technologies through performance verification and dissemination of information. It seeks to achieve this goal by providing high-quality, peer r...

  1. The Evolution of Improved Baghouse Filter Media as Observed in the Environmental Technology Verification Program

    EPA Science Inventory

    The U.S. EPA implemented the Environmental Technology Verification (ETV) program in 1995 to generate independent and credible data on the performance of innovative technologies that have the potential to improve protection of public health and the environment. Results are publicl...

  2. Environmental Technology Verification--Baghouse Filtration Products: GE Energy QG061 Filtration Media (Tested September 2008)

    EPA Science Inventory

    This report reviews the filtration and pressure drop performance of GE Energy's QG061 filtration media. Environmental Technology Verification (ETV) testing of this technology/product was conducted during a series of tests in September 2008. The objective of the ETV Program is to ...

  3. Why is digit ratio correlated to sports performance?

    PubMed Central

    Kim, Tae Beom; Kim, Khae Hawn

    2016-01-01

    Second to fourth digit ratio is the ratio of second to fourth digit length. It has been known that digit ratio is sexually dimorphic in humans, such that males tend to have lower digit ratio (longer fourth digits relative to second digits) than females. Digit ratio is thought to be a biomarker of the balance between fetal testosterone (FT) and fetal estrogen (FE) in a relatively narrow developmental window at the end of the first trimester of pregnancy. On the contrary, the relationships between digit ratio and levels of sex steroids in adults are not clear. Most correlational studies between digit ratio and adult sex steroids have revealed that this association is statistically not significant. However, for many years, a lot of researches showed negative relationships between digit ratio and sports performance such as rugby, surfing, rowing, sprinting, endurance, and hand grip strength. Here, we discuss possible mechanisms about the relationships between digit ratio and sports performance. PMID:28119871

  4. Why is digit ratio correlated to sports performance?

    PubMed

    Kim, Tae Beom; Kim, Khae Hawn

    2016-12-01

    Second to fourth digit ratio is the ratio of second to fourth digit length. It has been known that digit ratio is sexually dimorphic in humans, such that males tend to have lower digit ratio (longer fourth digits relative to second digits) than females. Digit ratio is thought to be a biomarker of the balance between fetal testosterone (FT) and fetal estrogen (FE) in a relatively narrow developmental window at the end of the first trimester of pregnancy. On the contrary, the relationships between digit ratio and levels of sex steroids in adults are not clear. Most correlational studies between digit ratio and adult sex steroids have revealed that this association is statistically not significant. However, for many years, a lot of researches showed negative relationships between digit ratio and sports performance such as rugby, surfing, rowing, sprinting, endurance, and hand grip strength. Here, we discuss possible mechanisms about the relationships between digit ratio and sports performance.

  5. Effect of contact ratio on spur gear dynamic load

    NASA Technical Reports Server (NTRS)

    Liou, Chuen-Huei; Lin, Hsiang Hsi; Oswald, Fred B.; Townsend, Dennis P.

    1992-01-01

    A computer simulation is presented which shows how the gear contact ratio affects the dynamic load on a spur gear transmission. The contact ratio can be affected by the tooth addendum, the pressure angle, the tooth size (diametral pitch), and the center distance. The analysis presented was performed using the NASA gear dynamics code, DANST. In the analysis, the contact ratio was varied over the range 1.20 to 2.40 by changing the length of the tooth addendum. In order to simplify the analysis, other parameters related to contact ratio were held constant. The contact ratio was found to have a significant influence on gear dynamics. Over a wide range of operating speeds, a contact ratio close to 2.0 minimized dynamic load. For low contact ratio gears (contact ratio less than 2.0), increasing the contact ratio reduced the gear dynamic load. For high contact ratio gears (contact ratio = or greater than 2.0), the selection of contact ratio should take into consideration the intended operating speeds. In general, high contact ratio gears minimized dynamic load better than low contact ratio gears.

  6. Effect of contact ratio on spur gear dynamic load

    NASA Astrophysics Data System (ADS)

    Liou, Chuen-Huei; Lin, Hsiang Hsi; Oswald, Fred B.; Townsend, Dennis P.

    A computer simulation is presented which shows how the gear contact ratio affects the dynamic load on a spur gear transmission. The contact ratio can be affected by the tooth addendum, the pressure angle, the tooth size (diametral pitch), and the center distance. The analysis presented was performed using the NASA gear dynamics code, DANST. In the analysis, the contact ratio was varied over the range 1.20 to 2.40 by changing the length of the tooth addendum. In order to simplify the analysis, other parameters related to contact ratio were held constant. The contact ratio was found to have a significant influence on gear dynamics. Over a wide range of operating speeds, a contact ratio close to 2.0 minimized dynamic load. For low contact ratio gears (contact ratio less than 2.0), increasing the contact ratio reduced the gear dynamic load. For high contact ratio gears (contact ratio = or greater than 2.0), the selection of contact ratio should take into consideration the intended operating speeds. In general, high contact ratio gears minimized dynamic load better than low contact ratio gears.

  7. Critical international normalized ratio results after hours

    PubMed Central

    Korn, Darlene; Sean McMurtry, M.; George-Phillips, Kirsten; Bungard, Tammy J.

    2017-01-01

    Abstract Objective To determine whether the timing of notification of critical international normalized ratio (INR) results (during or after clinic hours) altered the clinician’s ability to affect same-day patient care. Design Retrospective chart review. Setting The Anticoagulation Management Service at the University of Alberta Hospital in Edmonton. Participants A total of 276 patients with critical INR results (> 5.0) separated by at least 30 days were identified to have 200 critical INR results reported during clinic hours and 200 reported after hours. Main outcome measures Differences in the proportion of patients with critical INR results having same-day care altered (by changing warfarin dose, administering vitamin K, or referring for assessment) between those with results reported during clinic hours compared with those with results reported after clinic hours. Differences by highly critical INR results (> 9.0 vs ≤ 9.0) and whether patients experienced thromboembolism or bleeding within 30 days were also assessed. Results Same-day patient care was affected for 174 out of 200 (87.0%) critical INR results reported during clinic hours compared with 101 out of 200 (50.5%) reported after clinic hours (P < .001). The most common reason for not being able to intervene was that warfarin had already been taken. Warfarin dose alteration was the most frequent change (97.1% during clinic hours and 96.0% after hours). When patients with INRs greater than 9.0 were assessed separately, the ability to affect care increased for INRs reported both during and after clinic hours (92.9% and 63.6%, respectively), largely attributable to oral vitamin K use. Overall, thromboembolic and major bleeding event rates were low and were similar in both groups. Conclusion Same-day care was less likely to be affected by critical INR results communicated after hours, most commonly because the patient had already taken their daily warfarin dose. However, after-hours care was still

  8. Enantiomer Ratios of Meteoritic Sugar Derivatives

    NASA Technical Reports Server (NTRS)

    Cooper, George

    2012-01-01

    Carbonaceous meteorites contain a diverse suite of soluble organic compounds. Studies of these compounds reveal the Solar System's earliest organic chemistry. Among the classes of organic compounds found in meteorites are keto acids (pyruvic acid, etc.), hydroxy tricarboxylic acids (1), amino acids, amides, purines and pyrimidines. The Murchison and Murray meteorites are the most studied for soluble and insoluble organic compounds and organic carbon phases. The majority of (indigenous) meteoritic compounds are racemic, (i.e., their D/L enantiomer ratios are 50:50). However, some of the more unusual (non-protein) amino acids contain slightly more of one enantiomer (usually the L) than the other. This presentation focuses on the enantiomer analyses of three to six-carbon (3C to 6C) meteoritic sugar acids. The molecular and enantiomer analysis of corresponding sugar alcohols will also be discussed. Detailed analytical procedures for sugar-acid enantiomers have been described. Results of several meteorite analyses show that glyceric acid is consistently racemic (or nearly so) as expected of non-biological mechanisms of synthesis. Also racemic are 4-C deoxy sugar acids: 2-methyl glyceric acid; 2,4-dihydroxybutyric acid; 2,3-dihydroxybutyric acid (two diastereomers); and 3,4-dihydroxybutyric acid. However, a 4C acid, threonic acid, has never been observed as racemic, i.e., it possesses a large D excess. In several samples of Murchison and one of GRA 95229 (possibly the most pristine carbonaceous meteorite yet analyzed) threonic acid has nearly the same D enrichment. In Murchison, preliminary isotopic measurements of individual threonic acid enantiomers point towards extraterrestrial sources of the D enrichment. Enantiomer analyses of the 5C mono-sugar acids, ribonic, arabinonic, xylonic, and lyxonic also show large D excesses. It is worth noting that all four of these acids (all of the possible straight-chained 5C sugar acids) are present in meteorites, including the

  9. Reinforcing Effects of d-Amphetamine: Influence of Novel Ratios on a Progressive-Ratio Schedule

    PubMed Central

    Sevak, Rajkumar J.; Stoops, William W.; Glaser, Paul E.A.; Hays, Lon R.; Rush, Craig R.

    2013-01-01

    Progressive-ratio schedules are useful for studying reinforcing effects of drugs. Previous human laboratory studies showed that d-amphetamine significantly increased break points relative to placebo levels. However, the magnitude of the increase was modest, which may be attributable to rather high levels of placebo responding. We utilized novel response requirements under the modified progressive-ratio schedule and hypothesized that the altered range of response requirements would decrease responding for placebo and increase responding for d-amphetamine. Eight participants completed the study. The participants first sampled oral doses of d-amphetamine (0, 8, 16 and 24 mg). In subsequent sessions, participants were offered the opportunity to work for the sampled dose on a modified progressive-ratio procedure with response requirements ranging from 400 to 1800 mouse clicks. A battery of participant-rated drug-effect questionnaires, a performance measure and cardiovascular measures were included in orderto characterize more fully the effects of d-amphetamine. Placebo maintained low levels of responding. The intermediate dose of d-amphetamine increased responding significantly above placebo levels. d-Amphetamine produced prototypical subject-rated effects that were an orderly function of dose. The present data suggest that the modified response requirements resulted in lower levels of placebo taking and a larger separation between number of placebo and d-amphetamine capsules earned. PMID:20944503

  10. EFFECTS OF A SIGNALED DELAY TO REINFORCEMENT IN THE PREVIOUS AND UPCOMING RATIOS ON BETWEEN-RATIO PAUSING IN FIXED-RATIO SCHEDULES

    PubMed Central

    Harris, Aimee; Foster, T. Mary; Levine, Joshua; Temple, William

    2012-01-01

    Domestic hens responded under multiple fixed-ratio fixed-ratio schedules with equal fixed ratios. One component provided immediate reinforcement and the other provided reinforcement after a delay, signaled by the offset of the key light. The components were presented quasirandomly so that all four possible transitions occurred in each session. The delay was varied over 0, 4, 8, 16, and 32 s with fixed-ratio 5 schedules, and over 0, 8 and 32 s with fixed-ratio 1, 15 and 40 schedules. Main effects of fixed-ratio value and delay duration were detected on between-ratio pauses. Pauses were longer when the multiple-schedule stimulus correlated with a delayed-reinforcer component was presented, with the longest pauses occurring at the transition from a component with an immediate reinforcer to one with a delayed reinforcer. Pause durations were shortest during immediate components. Overall, both the presence or absence of a delay in the upcoming component, and the presence or absence of a delay in the preceding component affected pause length, but the upcoming delay had the larger effect. Thus changes in delay had similar effects to past reports of the effects of changes in response force, response requirement, and reinforcer magnitude in multiple fixed-ratio fixed-ratio schedules. PMID:23144507

  11. 7 CFR 1425.10 - Financial ratio requirement.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... commodities, CMA's shall have a current ratio of at least 1 dollar of current assets for each 1 dollar of current liabilities (current ratio of 1:1 or better) on the balance sheet it submits to CCC with...

  12. 7 CFR 1425.10 - Financial ratio requirement.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... commodities, CMA's shall have a current ratio of at least 1 dollar of current assets for each 1 dollar of current liabilities (current ratio of 1:1 or better) on the balance sheet it submits to CCC with...

  13. THE ESSENTIAL DIFFERENCE BETWEEN THE TWO OPTIMUM PROPORTIONS FLOCCULATION RATIOS

    PubMed Central

    Boyd, William C.; Purnell, Marjorie A.

    1944-01-01

    The fact that the optimum proportion flocculation ratio is different when determined by the α (Dean and Webb) and β (Ramon) procedures is pointed out. It is demonstrated that this difference is a consequence of the difference in the two methods, and that the two optima, though they may in certain cases lie near together, can never coincide. A new ratio (the ε ratio), intermediate between the α and β ratios, and having theoretical advantages over both of them, is defined. PMID:19871416

  14. Confidence Interval Methodology for Ratio Means (CIM4RM)

    DTIC Science & Technology

    2010-08-01

    RDECOIW 40 Years of SAA Excellence in Analysis AMSAA TECHNICAL REPORT NO. TR-2010-35 CONFIDENCE INTERVAL METHODOLOGY FOR RATIO MEANS (CIM4RM...COVERED Technical Report 4 TITLE AND SUBTITLE Confidence Interval Methodology for Ratio Means (CIM4RM) 5 FUNDING NUMBERS 6 AUTHOR!SI John Nierwinski...LIST OF ACRONYMS CIM4RM - Confidence Interval Methodology for Ratio Means MH - Man-Hours MR - Maintenance Ratio PCM - Parts Cost per Mile CI

  15. Final Report on Isotope Ratio Techniques for Light Water Reactors

    SciTech Connect

    Gerlach, David C.; Gesh, Christopher J.; Hurley, David E.; Mitchell, Mark R.; Meriwether, George H.; Reid, Bruce D.

    2009-07-01

    The Isotope Ratio Method (IRM) is a technique for estimating the energy or plutonium production in a fission reactor by measuring isotope ratios in non-fuel reactor components. The isotope ratios in these components can then be directly related to the cumulative energy production with standard reactor modeling methods.

  16. [[On the change of sex ratio by the Japanese zodiac

    PubMed

    Sakai, H

    1989-04-01

    Changes in the sex ratio in Japan from 1899 to 1986 are analyzed using data from official sources. The emphasis is on differences in the sex ratio according to the signs of the Japanese zodiac. The author notes that although the significance of the zodiac on the sex ratio has been decreasing since the early 1970s, it still has a measurable impact.

  17. DC-to-AC inverter ratio failure detector

    NASA Technical Reports Server (NTRS)

    Ebersole, T. J.; Andrews, R. E.

    1975-01-01

    Failure detection technique is based upon input-output ratios, which is independent of inverter loading. Since inverter has fixed relationship between V-in/V-out and I-in/I-out, failure detection criteria are based on this ratio, which is simply inverter transformer turns ratio, K, equal to primary turns divided by secondary turns.

  18. 10 CFR 436.21 - Savings-to-investment ratio.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... is the ratio of the present value savings to the present value costs of an energy or water conservation measure. The numerator of the ratio is the present value of net savings in energy or water and non... conservation measure. The denominator of the ratio is the present value of the net increase in investment...

  19. Low porosity metallic periodic structures with negative Poisson's ratio.

    PubMed

    Taylor, Michael; Francesconi, Luca; Gerendás, Miklós; Shanian, Ali; Carson, Carl; Bertoldi, Katia

    2014-04-16

    Auxetic behavior in low porosity metallic structures is demonstrated via a simple system of orthogonal elliptical voids. In this minimal 2D system, the Poisson's ratio can be effectively controlled by changing the aspect ratio of the voids. In this way, large negative values of Poisson's ratio can be achieved, indicating an effective strategy for designing auxetic structures with desired porosity.

  20. Inferences about ungulate population dynamics derived from age ratios

    USGS Publications Warehouse

    Harris, N.C.; Kauffman, M.J.; Mills, L.S.

    2008-01-01

    Age ratios (e.g., calf:cow for elk and fawn:doe for deer) are used regularly to monitor ungulate populations. However, it remains unclear what inferences are appropriate from this index because multiple vital rate changes can influence the observed ratio. We used modeling based on elk (Cervus elaphus) life-history to evaluate both how age ratios are influenced by stage-specific fecundity and survival and how well age ratios track population dynamics. Although all vital rates have the potential to influence calf:adult female ratios (i.e., calf:xow ratios), calf survival explained the vast majority of variation in calf:adult female ratios due to its temporal variation compared to other vital rates. Calf:adult female ratios were positively correlated with population growth rate (??) and often successfully indicated population trajectories. However, calf:adult female ratios performed poorly at detecting imposed declines in calf survival, suggesting that only the most severe declines would be rapidly detected. Our analyses clarify that managers can use accurate, unbiased age ratios to monitor arguably the most important components contributing to sustainable ungulate populations, survival rate of young and ??. However, age ratios are not useful for detecting gradual declines in survival of young or making inferences about fecundity or adult survival in ungulate populations. Therefore, age ratios coupled with independent estimates of population growth or population size are necessary to monitor ungulate population demography and dynamics closely through time.

  1. 12 CFR 3.6 - Minimum capital ratios.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Minimum capital ratios. 3.6 Section 3.6 Banks... national banks must have and maintain the minimum risk-based capital ratio as set forth in appendix A (and, for certain banks, in appendix B). (b) Total assets leverage ratio. All national banks must have...

  2. 76 FR 77229 - Designated Reserve Ratio for 2012

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-12-12

    ... CORPORATION Designated Reserve Ratio for 2012 AGENCY: Federal Deposit Insurance Corporation (FDIC). ACTION: Notice of Designated Reserve Ratio for 2012. Pursuant to the Federal Deposit Insurance Act, the Board of Directors of the Federal Deposit Insurance Corporation designates that the Designated Reserve Ratio...

  3. 77 FR 74662 - Designated Reserve Ratio for 2013

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-12-17

    ... CORPORATION Designated Reserve Ratio for 2013 AGENCY: Federal Deposit Insurance Corporation (FDIC). ACTION: Notice of Designated Reserve Ratio for 2013. Pursuant to the Federal Deposit Insurance Act, the Board of Directors of the Federal Deposit Insurance Corporation designates that the Designated Reserve Ratio...

  4. Auditory Discrimination of Frequency Ratios: The Octave Singularity

    ERIC Educational Resources Information Center

    Bonnard, Damien; Micheyl, Christophe; Semal, Catherine; Dauman, Rene; Demany, Laurent

    2013-01-01

    Sensitivity to frequency ratios is essential for the perceptual processing of complex sounds and the appreciation of music. This study assessed the effect of ratio simplicity on ratio discrimination for pure tones presented either simultaneously or sequentially. Each stimulus consisted of four 100-ms pure tones, equally spaced in terms of…

  5. 78 FR 62633 - Designated Reserve Ratio for 2014

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-10-22

    ... CORPORATION Designated Reserve Ratio for 2014 AGENCY: Federal Deposit Insurance Corporation (FDIC). ACTION: Notice of Designated Reserve Ratio for 2014. Pursuant to the Federal Deposit Insurance Act, the Board of Directors of the Federal Deposit Insurance Corporation designates that the Designated Reserve Ratio...

  6. 28 CFR 97.14 - Guard-to-prisoner ratio.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 28 Judicial Administration 2 2011-07-01 2011-07-01 false Guard-to-prisoner ratio. 97.14 Section 97... PRISONER OR DETAINEE SERVICES § 97.14 Guard-to-prisoner ratio. Companies covered under this part must... entity from establishing more stringent guard-to-prisoner ratios....

  7. 26 CFR 1.72-4 - Exclusion ratio.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 26 Internal Revenue 2 2013-04-01 2013-04-01 false Exclusion ratio. 1.72-4 Section 1.72-4 Internal... TAXES (CONTINUED) Items Specifically Included in Gross Income § 1.72-4 Exclusion ratio. (a) General rule... annuities described in section 72(o) and § 1.122-1), an exclusion ratio is to be determined for...

  8. 41 CFR 109-27.5002 - Stores inventory turnover ratio.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... turnover ratio. 109-27.5002 Section 109-27.5002 Public Contracts and Property Management Federal Property....5002 Stores inventory turnover ratio. Comparison of investment in stores inventories to annual issues... comparison may be expressed either as a turnover ratio (dollar value of issues divided by dollar value...

  9. 26 CFR 1.72-4 - Exclusion ratio.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 26 Internal Revenue 2 2012-04-01 2012-04-01 false Exclusion ratio. 1.72-4 Section 1.72-4 Internal... TAXES (CONTINUED) Items Specifically Included in Gross Income § 1.72-4 Exclusion ratio. (a) General rule... annuities described in section 72(o) and § 1.122-1), an exclusion ratio is to be determined for...

  10. 7 CFR 1425.10 - Financial ratio requirement.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 10 2013-01-01 2013-01-01 false Financial ratio requirement. 1425.10 Section 1425.10... Financial ratio requirement. To be financially able to make advances to their members and to market their commodities, CMA's shall have a current ratio of at least 1 dollar of current assets for each 1 dollar...

  11. 28 CFR 97.14 - Guard-to-prisoner ratio.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 28 Judicial Administration 2 2010-07-01 2010-07-01 false Guard-to-prisoner ratio. 97.14 Section 97... PRISONER OR DETAINEE SERVICES § 97.14 Guard-to-prisoner ratio. Companies covered under this part must... entity from establishing more stringent guard-to-prisoner ratios....

  12. 26 CFR 26.2642-1 - Inclusion ratio.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 26 Internal Revenue 14 2011-04-01 2010-04-01 true Inclusion ratio. 26.2642-1 Section 26.2642-1... GENERATION-SKIPPING TRANSFER TAX REGULATIONS UNDER THE TAX REFORM ACT OF 1986 § 26.2642-1 Inclusion ratio. (a) In general. Except as otherwise provided in this section, the inclusion ratio is determined...

  13. 76 FR 60364 - Net Worth and Equity Ratio

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-09-29

    ... ADMINISTRATION 12 CFR Parts 700, 701, 702, 725, and 741 RIN 3133-AD87 Net Worth and Equity Ratio AGENCY: National... worth'' and ``equity ratio'' in the Federal Credit Union Act. Through this final rule, NCUA is making... regulation and the definition of ``equity ratio'' as it appears in NCUA's Requirements for...

  14. 26 CFR 1.72-4 - Exclusion ratio.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 26 Internal Revenue 2 2010-04-01 2010-04-01 false Exclusion ratio. 1.72-4 Section 1.72-4 Internal... TAXES (CONTINUED) Items Specifically Included in Gross Income § 1.72-4 Exclusion ratio. (a) General rule... annuities described in section 72(o) and § 1.122-1), an exclusion ratio is to be determined for...

  15. 41 CFR 109-27.5002 - Stores inventory turnover ratio.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... turnover ratio. 109-27.5002 Section 109-27.5002 Public Contracts and Property Management Federal Property....5002 Stores inventory turnover ratio. Comparison of investment in stores inventories to annual issues... comparison may be expressed either as a turnover ratio (dollar value of issues divided by dollar value...

  16. 41 CFR 109-27.5002 - Stores inventory turnover ratio.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... turnover ratio. 109-27.5002 Section 109-27.5002 Public Contracts and Property Management Federal Property....5002 Stores inventory turnover ratio. Comparison of investment in stores inventories to annual issues... comparison may be expressed either as a turnover ratio (dollar value of issues divided by dollar value...

  17. 26 CFR 26.2642-1 - Inclusion ratio.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 26 Internal Revenue 14 2014-04-01 2013-04-01 true Inclusion ratio. 26.2642-1 Section 26.2642-1... GENERATION-SKIPPING TRANSFER TAX REGULATIONS UNDER THE TAX REFORM ACT OF 1986 § 26.2642-1 Inclusion ratio. (a) In general. Except as otherwise provided in this section, the inclusion ratio is determined...

  18. 7 CFR 1425.10 - Financial ratio requirement.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 10 2014-01-01 2014-01-01 false Financial ratio requirement. 1425.10 Section 1425.10... Financial ratio requirement. To be financially able to make advances to their members and to market their commodities, CMA's shall have a current ratio of at least 1 dollar of current assets for each 1 dollar...

  19. 42 CFR 403.215 - Loss ratio standards.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 42 Public Health 2 2012-10-01 2012-10-01 false Loss ratio standards. 403.215 Section 403.215... ratio standards. (a) The policy must be expected to return to the policyholders, in the form of... case of individual policies. (b) For purposes of loss ratio requirements, policies issued as a...

  20. 26 CFR 26.2642-1 - Inclusion ratio.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 26 Internal Revenue 14 2012-04-01 2012-04-01 false Inclusion ratio. 26.2642-1 Section 26.2642-1... GENERATION-SKIPPING TRANSFER TAX REGULATIONS UNDER THE TAX REFORM ACT OF 1986 § 26.2642-1 Inclusion ratio. (a) In general. Except as otherwise provided in this section, the inclusion ratio is determined...

  1. 26 CFR 26.2642-1 - Inclusion ratio.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 26 Internal Revenue 14 2013-04-01 2013-04-01 false Inclusion ratio. 26.2642-1 Section 26.2642-1... GENERATION-SKIPPING TRANSFER TAX REGULATIONS UNDER THE TAX REFORM ACT OF 1986 § 26.2642-1 Inclusion ratio. (a) In general. Except as otherwise provided in this section, the inclusion ratio is determined...

  2. 28 CFR 97.14 - Guard-to-prisoner ratio.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 28 Judicial Administration 2 2014-07-01 2014-07-01 false Guard-to-prisoner ratio. 97.14 Section 97... PRISONER OR DETAINEE SERVICES § 97.14 Guard-to-prisoner ratio. Companies covered under this part must... entity from establishing more stringent guard-to-prisoner ratios....

  3. 41 CFR 109-27.5002 - Stores inventory turnover ratio.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... turnover ratio. 109-27.5002 Section 109-27.5002 Public Contracts and Property Management Federal Property....5002 Stores inventory turnover ratio. Comparison of investment in stores inventories to annual issues... comparison may be expressed either as a turnover ratio (dollar value of issues divided by dollar value...

  4. 42 CFR 403.215 - Loss ratio standards.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 42 Public Health 2 2013-10-01 2013-10-01 false Loss ratio standards. 403.215 Section 403.215... ratio standards. (a) The policy must be expected to return to the policyholders, in the form of... case of individual policies. (b) For purposes of loss ratio requirements, policies issued as a...

  5. 42 CFR 403.215 - Loss ratio standards.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 42 Public Health 2 2011-10-01 2011-10-01 false Loss ratio standards. 403.215 Section 403.215... ratio standards. (a) The policy must be expected to return to the policyholders, in the form of... case of individual policies. (b) For purposes of loss ratio requirements, policies issued as a...

  6. 28 CFR 97.14 - Guard-to-prisoner ratio.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 28 Judicial Administration 2 2013-07-01 2013-07-01 false Guard-to-prisoner ratio. 97.14 Section 97... PRISONER OR DETAINEE SERVICES § 97.14 Guard-to-prisoner ratio. Companies covered under this part must... entity from establishing more stringent guard-to-prisoner ratios....

  7. 26 CFR 1.72-4 - Exclusion ratio.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 26 Internal Revenue 2 2014-04-01 2014-04-01 false Exclusion ratio. 1.72-4 Section 1.72-4 Internal... TAXES (CONTINUED) Items Specifically Included in Gross Income § 1.72-4 Exclusion ratio. (a) General rule... annuities described in section 72(o) and § 1.122-1), an exclusion ratio is to be determined for...

  8. 26 CFR 1.72-4 - Exclusion ratio.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 26 Internal Revenue 2 2011-04-01 2011-04-01 false Exclusion ratio. 1.72-4 Section 1.72-4 Internal... TAXES (CONTINUED) Items Specifically Included in Gross Income § 1.72-4 Exclusion ratio. (a) General rule... annuities described in section 72(o) and § 1.122-1), an exclusion ratio is to be determined for...

  9. 7 CFR 1425.10 - Financial ratio requirement.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 10 2012-01-01 2012-01-01 false Financial ratio requirement. 1425.10 Section 1425.10... Financial ratio requirement. To be financially able to make advances to their members and to market their commodities, CMA's shall have a current ratio of at least 1 dollar of current assets for each 1 dollar...

  10. 42 CFR 403.215 - Loss ratio standards.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 42 Public Health 2 2014-10-01 2014-10-01 false Loss ratio standards. 403.215 Section 403.215... ratio standards. (a) The policy must be expected to return to the policyholders, in the form of... case of individual policies. (b) For purposes of loss ratio requirements, policies issued as a...

  11. 41 CFR 109-27.5002 - Stores inventory turnover ratio.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... turnover ratio. 109-27.5002 Section 109-27.5002 Public Contracts and Property Management Federal Property....5002 Stores inventory turnover ratio. Comparison of investment in stores inventories to annual issues... comparison may be expressed either as a turnover ratio (dollar value of issues divided by dollar value...

  12. 28 CFR 97.14 - Guard-to-prisoner ratio.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 28 Judicial Administration 2 2012-07-01 2012-07-01 false Guard-to-prisoner ratio. 97.14 Section 97... PRISONER OR DETAINEE SERVICES § 97.14 Guard-to-prisoner ratio. Companies covered under this part must... entity from establishing more stringent guard-to-prisoner ratios....

  13. NEUTROPHIL/LYMPHOCYTE RATIO AND PLATELET/LYMPHOCYTE RATIO IN PATIENTS WITH NSCLC

    PubMed Central

    Cukic, Vesna

    2016-01-01

    Objective: to compare neutrophil/lymphocyte ratio (NLR) and platelet/lymphocyte ratio (PLR) in patients with NSCLC (Non- Small- Cell Lung Cancer): with and without metastases at the time of diagnosis to find out if there is the importance of these cell ratios in the assessment of severity NSCLC. Material and Methods: this is the retrospective analysis of NRL and PRL in patients with NSCLC at the time of the diagnosis of disease before any anti tumor treatment (chemotherapy, radiotherapy, surgery). 57 of patients with NSCLC treated in the first three months of 2016. year were chosen at random regardless of sex and age. We examined full blood count cells (FBC), calculated NLR and PLR in every patient and compared obtained values in patients with and patients without metastases. Results: In 57 patients with NSCLC there were 15 males with metastases, 28 without metastases, and 8 females with metastases, 6 without metastases. Since there was no regularity in the distribution of obtained values of NLR and PLR we made the Mann-Whitney U test. Mean values are presented with a median and interquartile percentiles. There was no significant difference in NLR between patients without and with metastases (p = 0.614; p = NS) as well as in PLR (p=0,068; p=NS). Conclusion: There must be a link between the immune status of the organism and lung cancer development. Immune cells have become of interest in recent years and much work has been done to study their role in the genesis of cancer but it did not give satisfactory results. Further clinical studies on large number of patients and further laboratory examination of the role of immune cells in cancer development and suppression are required. PMID:27999489

  14. Activity ratios of ribulose-1,5-bisphosphate carboxylase accurately reflect carbamylation ratios. [Phaseolus vulgaris, Spinacla oleracea

    SciTech Connect

    Butz, N.D.; Sharkey, T.D. )

    1989-03-01

    Activity ratios and carbamylation ratios of ribulose-1,5-bisphosphate carboxylase (RuBPCase) were determined for leaves of Phaseolus vulgaris and Spinacia oleracea exposed to a variety of partial pressures of CO{sub 2} and O{sub 2} and photon flux densities (PFD). It was found that activity ratios accurately predicted carbamylation ratios except in extracts from leaves held in low PFD. In particular, it was confirmed that the loss of FuBPCase activity in low partial pressure of O{sub 2} and high PFD results from reduced carbamylation. Activity ratios of RuBPCase were lower than carbamylation ratios for Phaseolus leaves sampled in low PFD, presumably because of the presence of 2-carboxyarabinitol 1-phosphate. Spinacia leaves sampled in darkness also exhibited lower activity ratios than carbamylation ratios indicating that this species may also have an RuBPCase inhibitor even though carboxyarabinitol 1-phosphate has not been detected in this species in the past.

  15. Elevated sacroilac joint uptake ratios in systemic lupus erythematosus

    SciTech Connect

    De Smet, A.A.; Mahmood, T.; Robinson, R.G.; Lindsley, H.B.

    1984-08-01

    Sacroiliac joint radiographs and radionuclide sacroiliac joint uptake ratios were obtained on 14 patients with active systemic lupus erythematosus. Elevated joint ratios were found unilaterally in two patients and bilaterally in seven patients when their lupus was active. In patients whose disease became quiescent, the uptake ratios returned to normal. Two patients had persistently elevated ratios with continued clinical and laboratory evidence of active lupus. Mild sacroiliac joint sclerosis and erosions were detected on pelvic radiographs in these same two patients. Elevated quantitative sacroiliac joint uptake ratios may occur as a manifestation of active systemic lupus erythematosus.

  16. Income replacement ratios in the Health and Retirement Study.

    PubMed

    Purcell, Patrick J

    2012-01-01

    This article describes the income replacement ratio as a measure of retirement income adequacy and identifies several issues analysts must consider when calculating a replacement ratio. The article presents the income replacement ratios experienced by participants in the original sample cohort of the Health and Retirement Study (HRS), who were born between 1931 and 1941. Replacement ratios are shown by the respondent's birth cohort, age when first classified as retired in the HRS, and preretirement income quartile. Median replacement ratios fall as the retirement period grows longer.

  17. How the oxygen isotope ratio of rain water influences the isotope ratio of chicken eggshell carbonate

    NASA Astrophysics Data System (ADS)

    Price, Gregory; Grimes, Stephen

    2015-04-01

    The stable oxygen isotope ratio of chicken eggshell carbonate was analysed from chicken eggs laid under free range, and organic farming regimes from across the UK. The eggshell carbonate oxygen isotope data shows a clear depletion in delta18O distribution from the southwest to the northeast. Although consistently offset by around 1 permil, the same isotopic distribution as that seen in eggshell carbonate is observed in the delta18O ratio of rainfall and groundwater from across the UK. This distribution is related to the Rayleigh distillation of rainfall driven by westerly winds across the UK landmass. The clear relationship observed between eggshell delta18O values and that of rainwater presumably reflects the nature of free range chickens which must be drinking locally derived rainwater and supplementing their diet and water intake with locally derived food. These results suggest that the oxygen isotope value of chicken eggshells can be used as a forensic tool to identify the locality that free range and organic eggs were laid within the UK. Furthermore, if suitable material is preserved in the archaeological and geological record then such a relationship can potentially be used to establish the oxygen isotope value of rainwater from which ancient and / or ancestral birds lived.

  18. Ratio maps of iron ore deposits Atlantic City district, Wyoming

    NASA Technical Reports Server (NTRS)

    Vincent, R. K.

    1973-01-01

    Preliminary results of a spectral rationing technique are shown for a region at the southern end of the Wind River Range, Wyoming. Digital ratio graymaps and analog ratio images have been produced for the test site, but ground truth is not yet available for thorough interpretation of these products. ERTS analog ratio images were found generally better than either ERTS single-channel images or high altitude aerial photos for the discrimination of vegetation from non-vegetation in the test site region. Some linear geological features smaller than the ERTS spatial resolution are seen as well in ERTS ratio and single-channel images as in high altitude aerial photography. Geochemical information appears to be extractable from ERTS data. Good preliminary quantitative agreement between ERTS-derived ratios and laboratory-derived reflectance ratios of rocks and minerals encourage plans to use lab data as training sets for a simple ratio gating logic approach to automatic recognition maps.

  19. The Use of Capacity Ratios in Introductory Pharmacy Practice Experiences

    PubMed Central

    Haswell, Jamie L.; Byrd, Debbie C.; Foster, Stephan

    2012-01-01

    Objective. To describe the use of capacity ratios following the assignment of introductory pharmacy practice experiences (IPPEs) to a rising third-year pharmacy (P3) class. Methods. Practice experience availability for IPPEs was collected by means of preceptor response to requests. Following assignment of IPPEs to the rising P3 class, capacity ratios from the IPPEs available across the entire state and within each of 4 geographic zones were calculated. Capacity ratios for both community pharmacy and institutional pharmacy also were calculated. Results. The capacity ratio for IPPEs across the entire state was 2.11, which documents solvency. When the capacity ratios were calculated individually for community pharmacy and institutional pharmacy, solvency was also achieved. Likewise, IPPE capacity ratios were solvent in all 4 geographic zones. Conclusions. Capacity ratios are helpful in evaluating IPPE availability as they can be used to determine practice experience need in either type of practice experience or geographic zone. PMID:23193336

  20. Platelet to lymphocyte ratio and neutrophil to lymphocyte ratio in patients with rheumatoid arthritis

    PubMed Central

    Peng, You-Fan; Cao, Ling; Zeng, Yan-Hua; Zhang, Zhao-Xia; Chen, Dan; Zhang, Qiong

    2015-01-01

    Objectives It has been well documented that the platelet to lymphocyte ratio (PLR) and the neutrophil to lymphocyte ratio (NLR) are associated with outcomes for patients with gastric cancer, non-small cell lung cancer and acute heart failure. Inflammation may be the hidden factor that explains the correlation between NLP, PLR, and these diseases. However, to date, the data concerning NLR, PLR, and its association with inflammation are lacking in patients with rheumatoid arthritis (RA), thus, our aim to discuss whether NLR and PLR are associated with RA. Methods Patients with RA and healthy individuals were included according to the determined criteria, and laboratory indicators were measured. Results PLR and NLR were significantly higher in RA patients compared with healthy controls (3.20±2.06 vs. 1.56±0.47, P<0.01; 192.85±101.78 vs. 103.49±28.68, P<0.01). When leukocytes, neutrophil percentage, neutrophil, lymphocyte, platelet, C-reactive protein (CRP), erythrocyte sedimentation rate (ESR), and rheumatoid factor (RF) were considered as confounders (crude model), our results indicated that ESR and RF were correlated to RA. Of note, ESR, RF, and PLR were associated with RA after further adjustment based on crude model for PLR and NLR. Receiver operating characteristic (ROC) curves analysis showed that PLR values higher than >115.7 evaluated RA with a sensitivity of 82.5%, a specificity of 74.8% and area under the curve ( AUC ) of 0.847. Conclusions Our results suggest that PLR is associated with RA, and PLR may be an underlying indicator indicating the chronic subclinical inflammation in patients with RA. PMID:28352702

  1. [Using log-binomial model for estimating the prevalence ratio].

    PubMed

    Ye, Rong; Gao, Yan-hui; Yang, Yi; Chen, Yue

    2010-05-01

    To estimate the prevalence ratios, using a log-binomial model with or without continuous covariates. Prevalence ratios for individuals' attitude towards smoking-ban legislation associated with smoking status, estimated by using a log-binomial model were compared with odds ratios estimated by logistic regression model. In the log-binomial modeling, maximum likelihood method was used when there were no continuous covariates and COPY approach was used if the model did not converge, for example due to the existence of continuous covariates. We examined the association between individuals' attitude towards smoking-ban legislation and smoking status in men and women. Prevalence ratio and odds ratio estimation provided similar results for the association in women since smoking was not common. In men however, the odds ratio estimates were markedly larger than the prevalence ratios due to a higher prevalence of outcome. The log-binomial model did not converge when age was included as a continuous covariate and COPY method was used to deal with the situation. All analysis was performed by SAS. Prevalence ratio seemed to better measure the association than odds ratio when prevalence is high. SAS programs were provided to calculate the prevalence ratios with or without continuous covariates in the log-binomial regression analysis.

  2. Vehicular Slip Ratio Control Using Nonlinear Control Theory

    NASA Astrophysics Data System (ADS)

    Ikeda, Yuichi; Nakajima, Takashi; Chida, Yuichi

    In this paper, we discuss integrated vehicle slip ratio control under both deceleration and acceleration without the need for controller switching, and also propose a design method for such an integrated slip ratio controller based on the slip ratio dynamics. When a vehicle switches from acceleration to deceleration and vice versa, the slip ratio varies discontinuously. Here, the slip ratio is approximated to a continuous function by using a sigmoid function. And a controller is then designed by using feedback linearization based on the approximated slip ratio. The stability of the designed control system is proven by Lyapunov stability theorem. Furthermore, we propose a robust control method based on a disturbance observer and sliding mode control theory. Finally, the effectiveness of the proposed control method is verified through numerical simulation.

  3. Estimating differences and ratios in median times to event

    PubMed Central

    Rogawski, Elizabeth T.; Westreich, Daniel J.; Kang, Gagandeep; Ward, Honorine D.; Cole, Stephen R.

    2016-01-01

    Time differences and time ratios are often more interpretable estimates of effect than hazard ratios for time-to-event data, especially for common outcomes. We developed a SAS macro for estimating time differences and time ratios between baseline-fixed binary exposure groups based on inverse probability weighted Kaplan-Meier curves. The macro uses pooled logistic regression to calculate inverse probability of censoring and exposure weights, draws Kaplan-Meier curves based on the weighted data, and estimates the time difference and time ratio at a user-defined survival proportion. The macro also calculates the risk difference and risk ratio at a user-specified time. Confidence intervals are constructed by bootstrap. We provide an example assessing the effect of exclusive breastfeeding during diarrhea on the incidence of subsequent diarrhea in children followed from birth to 3 years in Vellore, India. The SAS macro provided here should facilitate the wider reporting of time differences and time ratios. PMID:27465526

  4. Method of Poisson's ratio imaging within a material part

    NASA Technical Reports Server (NTRS)

    Roth, Don J. (Inventor)

    1996-01-01

    The present invention is directed to a method of displaying the Poisson's ratio image of a material part. In the present invention longitudinal data is produced using a longitudinal wave transducer and shear wave data is produced using a shear wave transducer. The respective data is then used to calculate the Poisson's ratio for the entire material part. The Poisson's ratio approximations are then used to displayed the image.

  5. Sex investment ratios in eusocial Hymenoptera support inclusive fitness theory.

    PubMed

    Bourke, A F G

    2015-11-01

    Inclusive fitness theory predicts that sex investment ratios in eusocial Hymenoptera are a function of the relatedness asymmetry (relative relatedness to females and males) of the individuals controlling sex allocation. In monogynous ants (with one queen per colony), assuming worker control, the theory therefore predicts female-biased sex investment ratios, as found in natural populations. Recently, E.O. Wilson and M.A. Nowak criticized this explanation and presented an alternative hypothesis. The Wilson-Nowak sex ratio hypothesis proposes that, in monogynous ants, there is selection for a 1 : 1 numerical sex ratio to avoid males remaining unmated, which, given queens exceed males in size, results in a female-biased sex investment ratio. The hypothesis also asserts that, contrary to inclusive fitness theory, queens not workers control sex allocation and queen-worker conflict over sex allocation is absent. Here, I argue that the Wilson-Nowak sex ratio hypothesis is flawed because it contradicts Fisher's sex ratio theory, which shows that selection on sex ratio does not maximize the number of mated offspring and that the sex ratio proposed by the hypothesis is not an equilibrium for the queen. In addition, the hypothesis is not supported by empirical evidence, as it fails to explain 'split' (bimodal) sex ratios or data showing queen and worker control and ongoing queen-worker conflict. By contrast, these phenomena match predictions of inclusive fitness theory. Hence, the Wilson-Nowak sex ratio hypothesis fails both as an alternative hypothesis for sex investment ratios in eusocial Hymenoptera and as a critique of inclusive fitness theory.

  6. Measurement of continuous distributions of ventilation-perfusion ratios - Theory

    NASA Technical Reports Server (NTRS)

    Wagner, P. D.; Saltzman, H. A.; West, J. B.

    1974-01-01

    The resolution of the technique considered is sufficient to describe smooth distributions containing blood flow to unventilated regions (shunt), ventilation to unperfused regions (dead space), and up to three additional modes over the range of finite ventilation-perfusion ratios. In particular, areas whose ventilation-perfusion ratios are low can be separated from unventilated regions and those whose ventilation-perfusion ratios are high can similarly be distinguished from unperfused areas.

  7. Helping Students with Mathematics Difficulties Understand Ratios and Proportions

    ERIC Educational Resources Information Center

    Dougherty, Barbara; Bryant, Diane Pedrotty; Bryant, Brian R.; Shin, Mikyung

    2016-01-01

    Cara, a seventh-grade student with learning disabilities (LD) in mathematics, believes that the ratio 2:3 is equivalent to 4:5 because there is a difference of one between the two numbers in each ratio and there is a difference of two between corresponding numbers in the two ratios (2 + 2 = 4 and 3 + 2 = 5). This misconception affects her ability…

  8. Regulation of the Docosapentaenoic Acid/Docosahexaenoic Acid Ratio (DPA/DHA Ratio) in Schizochytrium limacinum B4D1.

    PubMed

    Zhang, Ke; Li, Huidong; Chen, Wuxi; Zhao, Minli; Cui, Haiyang; Min, Qingsong; Wang, Haijun; Chen, Shulin; Li, Demao

    2016-11-10

    Docosapentaenoic acid/docosahexaenoic acid ratio (DPA/DHA ratio) in Schizochytrium was relatively stable. But ideally the ratio of DPA/DHA will vary according to the desired end use. This study reports several ways of modulating the DPA/DHA ratio. Incubation times changed the DPA/DHA ratio, and changes in this ratio were associated with the variations in the saturated fatty acid (SFAs) content. Propionic acid sharply increased the SFAs content in lipids, dramatically decreased the even-chain SFAs content, and reduced the DPA/DHA ratio. Pentanoic acid (C5:0) and heptanoic acid (C7:0) had similar effects as propionic acid, whereas butyric acid (C4:0), hexanoic acid (C6:0), and octanoic acid (C8:0) did not change the fatty acid profile and the DPA/DHA ratio. Transcription analyses show that β-oxidation might be responsible for this phenomenon. Iodoacetamide upregulated polyunsaturated fatty acid (PUFA) synthase genes, reduced the DHA content, and improved the DPA content, causing the DPA/DHA ratio to increase. These results present new insights into the regulation of the DPA/DHA ratio.

  9. Prediction of release ratios of multicomponent pheromones from rubber septa.

    PubMed

    Heath, R R; Teal, P E; Tumlinson, J H; Mengelkoch, L J

    1986-12-01

    A method has been developed to predict the release ratio of the components of blends of alcohols, acetates, and/or aldehydes from rubber septa. The calculations of predicted release ratios are based on the relative vapor pressures of the components. The relative vapor pressures of the compounds were calculated from their retention indices on a liquid crystal capillary gas chromatographie column. The correlation between the theoretically predicted and experimentally determined ratios was very good. Thus, formulations can be prepared that will release a desired ratio of the components of a multicomponent pheromone blend.

  10. Effect of the Lebanese civil war on sex ratio.

    PubMed

    Abu-Musa, Antoine; Usta, Ihab; Hannoun, Antoine; Nassar, Anwar

    2008-01-01

    Sex ratio is a subject of scientific interest but little is known about the factors that affect the sex ratio of humans. The aim of this study was to assess the effect of the Lebanese civil war on sex ratio. Data on all live births delivered at a large university hospital for the years 1977-2005 were used in this study. Study periods were defined as wartime (1977-1992) and post-war (1993-2005). The sex ratio in the study time period was calculated as the male proportion, i.e. males/males + females in live-born infants. Sex ratio during the war was compared with that of the post-war period. The sex ratio was similar in the war and post-war period (0.515 versus 0.513; OR = 1.007; 95% CI 0.98-1.04). The annual variation in the sex ratio during the study period did not show any significant change in any of the years. In conclusion, the Lebanese civil war did not cause a detectable change in sex ratio at birth. Factors that might have affected the sex ratio include the nature of the study population (civilians), the variable intensity of war in different periods, and the effect of stress and environmental toxins.

  11. Gradient index plasmonic ring resonator with high extinction ratio

    NASA Astrophysics Data System (ADS)

    Zhou, Zidong; He, Pengbin; Xu, Jinyou; Zhuang, Xiujuan; Li, Yunyun; Pan, Anlian

    2014-02-01

    We propose and investigate a compact gradient index plasmonic ring resonator (Grin PRR) with strong light confinement and extinction ratio based on finite element method (FEM). Theoretical simulation reveals that the change of index gradient influences the resonant frequency, Q factor and the mode volume. Significantly, it is demonstrated that the extinction ratio of Grin PRR can be optimized by varying the index gradient for any radius. Index gradient can enhance extinction ratio at settled size, so this structure has both high extinction ratio and smaller size footprint. It could be very promising for the high-density optical integration.

  12. Statistical inference for tumor growth inhibition T/C ratio.

    PubMed

    Wu, Jianrong

    2010-09-01

    The tumor growth inhibition T/C ratio is commonly used to quantify treatment effects in drug screening tumor xenograft experiments. The T/C ratio is converted to an antitumor activity rating using an arbitrary cutoff point and often without any formal statistical inference. Here, we applied a nonparametric bootstrap method and a small sample likelihood ratio statistic to make a statistical inference of the T/C ratio, including both hypothesis testing and a confidence interval estimate. Furthermore, sample size and power are also discussed for statistical design of tumor xenograft experiments. Tumor xenograft data from an actual experiment were analyzed to illustrate the application.

  13. The human heart: application of the golden ratio and angle.

    PubMed

    Henein, Michael Y; Zhao, Ying; Nicoll, Rachel; Sun, Lin; Khir, Ashraf W; Franklin, Karl; Lindqvist, Per

    2011-08-04

    The golden ratio, or golden mean, of 1.618 is a proportion known since antiquity to be the most aesthetically pleasing and has been used repeatedly in art and architecture. Both the golden ratio and the allied golden angle of 137.5° have been found within the proportions and angles of the human body and plants. In the human heart we found many applications of the golden ratio and angle, in addition to those previously described. In healthy hearts, vertical and transverse dimensions accord with the golden ratio, irrespective of different absolute dimensions due to ethnicity. In mild heart failure, the ratio of 1.618 was maintained but in end-stage heart failure the ratio significantly reduced. Similarly, in healthy ventricles mitral annulus dimensions accorded with the golden ratio, while in dilated cardiomyopathy and mitral regurgitation patients the ratio had significantly reduced. In healthy patients, both the angles between the mid-luminal axes of the pulmonary trunk and the ascending aorta continuation and between the outflow tract axis and continuation of the inflow tract axis of the right ventricle approximate to the golden angle, although in severe pulmonary hypertension, the angle is significantly increased. Hence the overall cardiac and ventricular dimensions in a normal heart are consistent with the golden ratio and angle, representing optimum pump structure and function efficiency, whereas there is significant deviation in the disease state. These findings could have anatomical, functional and prognostic value as markers of early deviation from normality.

  14. High/variable mixture ratio O2/H2 engine

    NASA Technical Reports Server (NTRS)

    Adams, A.; Parsley, R. C.

    1988-01-01

    Vehicle/engine analysis studies have identified the High/Dual Mixture Ratio O2/H2 Engine cycle as a leading candidate for an advanced Single Stage to Orbit (SSTO) propulsion system. This cycle is designed to allow operation at a higher than normal O/F ratio of 12 during liftoff and then transition to a more optimum O/F ratio of 6 at altitude. While operation at high mixture ratios lowers specific impulse, the resultant high propellant bulk density and high power density combine to minimize the influence of atmospheric drag and low altitude gravitational forces. Transition to a lower mixture ratio at altitude then provides improved specific impulse relative to a single mixture ratio engine that must select a mixture ratio that is balanced for both low and high altitude operation. This combination of increased altitude specific impulse and high propellant bulk density more than offsets the compromised low altitude performance and results in an overall mission benefit. Two areas of technical concern relative to the execution of this dual mixture ratio cycle concept are addressed. First, actions required to transition from high to low mixture ratio are examined, including an assessment of the main chamber environment as the main chamber mixture ratio passes through stoichiometric. Secondly, two approaches to meet a requirement for high turbine power at high mixture ratio condition are examined. One approach uses high turbine temperature to produce the power and requires cooled turbines. The other approach incorporates an oxidizer-rich preburner to increase turbine work capability via increased turbine mass flow.

  15. Stable carbon isotope ratios of ambient aromatic volatile organic compounds

    NASA Astrophysics Data System (ADS)

    Kornilova, Anna; Huang, Lin; Saccon, Marina; Rudolph, Jochen

    2016-09-01

    Measurements of mixing ratios and stable carbon isotope ratios of aromatic volatile organic compounds (VOC) in the atmosphere were made in Toronto (Canada) in 2009 and 2010. Consistent with the kinetic isotope effect for reactions of aromatic VOC with the OH radical the observed stable carbon isotope ratios are on average significantly heavier than the isotope ratios of their emissions. The change of carbon isotope ratio between emission and observation is used to determine the extent of photochemical processing (photochemical age, [OH]dt) of the different VOC. It is found that [OH]dt of different VOC depends strongly on the VOC reactivity. This demonstrates that for this set of observations the assumption of a uniform [OH]dt for VOC with different reactivity is not justified and that the observed values for [OH]dt are the result of mixing of VOC from air masses with different values for [OH]dt. Based on comparison between carbon isotope ratios and VOC concentration ratios it is also found that the varying influence of sources with different VOC emission ratios has a larger impact on VOC concentration ratios than photochemical processing. It is concluded that for this data set the use of VOC concentration ratios to determine [OH]dt would result in values for [OH]dt inconsistent with carbon isotope ratios and that the concept of a uniform [OH]dt for an air mass has to be replaced by the concept of individual values of an average [OH]dt for VOC with different reactivity.

  16. Sex ratios in fetuses and liveborn infants with autosomal aneuploidy

    SciTech Connect

    Heuther, C.A.; Martin, R.L.M.; Stoppelman, S.M.

    1996-06-14

    Ten data sources were used substantially to increase the available data for estimating fetal and livebirth sex ratios for Patau (trisomy 13), Edwards (trisomy 18), and Down (trisomy 21) syndromes and controls. The fetal sex ratio estimate was 0.88 (N = 584) for trisomy 13, 0.90 (N = 1702) for trisomy 18, and 1.16 (N = 3154) for trisomy 21. All were significantly different from prenatal controls (1.07). The estimated ratios in prenatal controls were 1.28 (N = 1409) for CVSs and 1.06 (N = 49427) for amniocenteses, indicating a clear differential selection against males, mostly during the first half of fetal development. By contrast, there were no sex ratio differences for any of the trisomies when comparing gestational ages <16 and >16 weeks. The livebirth sex ratio estimate was 0.90 (N = 293) for trisomy 13, 0.63 (N = 497) for trisomy 18, and 1.15 (N = 6424) for trisomy 21, the latter two being statistically different than controls (1.05) (N = 3660707). These ratios for trisomies 13 and 18 were also statistically different than the ratio for trisomy 21. Only in trisomy 18 did the sex ratios in fetuses and livebirths differ, indicating a prenatal selection against males >16 weeks. No effects of maternal age or race were found on these estimates for any of the fetal or livebirth trisomies. Sex ratios for translocations and mosaics were also estimated for these aneuploids. Compared to previous estimates, these results are less extreme, most likely because of larger sample sizes and less sample bias. They support the hypothesis that these trisomy sex ratios are skewed at conception, or become so during embryonic development through differential intrauterine selection. The estimate for Down syndrome livebirths is also consistent with the hypothesis that its higher sex ratio is associated with paternal nondisjunction. 36 refs., 5 tabs.

  17. New Examination of the Traditional Raman Lidar Technique II: Temperature Dependence Aerosol Scattering Ratio and Water Vapor Mixing Ratio Equations

    NASA Technical Reports Server (NTRS)

    Whiteman, David N.; Abshire, James B. (Technical Monitor)

    2002-01-01

    In a companion paper, the temperature dependence of Raman scattering and its influence on the Raman water vapor signal and the lidar equations was examined. New forms of the lidar equation were developed to account for this temperature sensitivity. Here we use those results to derive the temperature dependent forms of the equations for the aerosol scattering ratio, aerosol backscatter coefficient, extinction to backscatter ratio and water vapor mixing ratio. Pertinent analysis examples are presented to illustrate each calculation.

  18. Concept of planetary gear system to control fluid mixture ratio

    NASA Technical Reports Server (NTRS)

    Mcgroarty, J. D.

    1966-01-01

    Mechanical device senses and corrects for fluid flow departures from the selected flow ratio of two fluids. This system has been considered for control of rocket engine propellant mixture control but could find use wherever control of the flow ratio of any two fluids is desired.

  19. 2D:4D Ratio and its Implications in Medicine

    PubMed Central

    Jeevanandam, Saravanakumar

    2016-01-01

    Digit ratios, especially 2D:4D ratio, a potential proxy marker for prenatal androgen exposure shows sexual dimorphism. Existing literature and recent research show accumulating evidence on 2D:4D ratio showing correlations with various phenotypic traits in humans. Ratio of 2D:4D is found to correlate negatively to testosterone and positively to oestrogen in the foetus. Interestingly, it is constant since birth and not influenced by the adult hormone levels. Usually, males have lower ratios when compared to females. Prenatal androgen exposure and therefore, digit ratios have been reported to be associated with numerical competencies, spatial skills, handedness, cognitive abilities, academic performance, sperm counts, personalities and prevalence of obesity, migraine, eating disorders, depression, myopia, autism etc. The authors have attempted to write a brief account on the digit ratios and the dimorphism observed in various physiological, psychological and behavioural traits. Also, the authors have discussed the relevant molecular basics and the methods of measurement of digit ratios. PMID:28208851

  20. Equilibrium studies for low-aspect-ratio torsatrons

    SciTech Connect

    Garcia, L.; Carreras, B.A.; Harris, J.H.; Hicks, H.R.; Lynch, V.E.

    1983-10-01

    Three-dimensional MHD equilibrium studies have been done for low aspect ratio torsatrons. These studies cover continuous-coil and modular torsatrons. The equilibrium properties improve with aspect ratio, as is expected. The role played by the vertical field has also been investigated. Outward shifts cause the flux surfaces to deteriorate. Inward shifts improve the flux surfaces at the expense of stability properties.

  1. The golden ratio in Schwarzschild-Kottler black holes

    NASA Astrophysics Data System (ADS)

    Cruz, Norman; Olivares, Marco; Villanueva, J. R.

    2017-02-01

    In this paper we show that the golden ratio is present in the Schwarzschild-Kottler metric. For null geodesics with maximal radial acceleration, the turning points of the orbits are in the golden ratio Φ =(√{5}-1)/2. This is a general result which is independent of the value and sign of the cosmological constant Λ.

  2. 12 CFR 3.6 - Minimum capital ratios.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 12 Banks and Banking 1 2011-01-01 2011-01-01 false Minimum capital ratios. 3.6 Section 3.6 Banks... maintain Tier 1 capital in an amount equal to at least 3.0 percent of adjusted total assets. (c) Additional... banks meeting the conditions set forth in this paragraph (c), the minimum Tier 1 leverage ratio is...

  3. 12 CFR 3.6 - Minimum capital ratios.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 12 Banks and Banking 1 2013-01-01 2013-01-01 false Minimum capital ratios. 3.6 Section 3.6 Banks... maintain Tier 1 capital in an amount equal to at least 3.0 percent of adjusted total assets. (c) Additional... banks meeting the conditions set forth in this paragraph (c), the minimum Tier 1 leverage ratio is...

  4. The Origin of the Ionic-Radius Ratio Rules

    ERIC Educational Resources Information Center

    Jensen, William B.

    2010-01-01

    In response to a reader query, this article traces the origins of the ionic-radius ratio rules and their incorrect attribution to Linus Pauling in the chemical literature and to Victor Goldschmidt in the geochemical literature. In actual fact, the ionic-radius ratio rules were first proposed within the context of the coordination chemistry…

  5. Fixed- and Variable-Ratio Reinforcement of Reading Performance.

    ERIC Educational Resources Information Center

    George, John E.

    The effects of fixed-ratio and variable-ratio reinforcement classroom reading performance was investigated. Subjects were 50 boys and 50 girls from four grade-2 classrooms of one elementary school. The subjects were divided into three reading levels, above-average, average, and below-average, and were randomly assigned to (1) a no-reinforcement…

  6. Auditory Discrimination of Frequency Ratios: The Octave Singularity

    PubMed Central

    Bonnard, Damien; Micheyl, Christophe; Semal, Catherine; Dauman, René; Demany, Laurent

    2014-01-01

    Sensitivity to frequency ratios is essential for the perceptual processing of complex sounds and the appreciation of music. This study assessed the effect of ratio simplicity on ratio discrimination for pure tones presented either simultaneously or sequentially. Each stimulus consisted of four 100-ms pure tones, equally spaced in terms of frequency ratio and presented at a low intensity to limit interactions in the auditory periphery. Listeners had to discriminate between a reference frequency ratio of 0.97 octave (about 1.96:1) and target frequency ratios, which were larger than the reference. In the simultaneous condition, the obtained psychometric functions were nonmonotonic: as the target frequency ratio increased from 0.98 octave to 1.04 octaves, discrimination performance initially increased, then decreased, and then increased again; performance was better when the target was exactly one octave (2:1) than when the target was slightly larger. In the sequential condition, by contrast, the psychometric functions were monotonic and there was no effect of frequency ratio simplicity. A control experiment verified that the nonmonotonicity observed in the simultaneous condition did not originate from peripheral interactions between the tones. Our results indicate that simultaneous octaves are recognized as “special” frequency intervals by a mechanism that is insensitive to the sign (positive or negative) of deviations from the octave, whereas this is apparently not the case for sequential octaves. PMID:23088507

  7. 42 CFR 403.215 - Loss ratio standards.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 42 Public Health 2 2010-10-01 2010-10-01 false Loss ratio standards. 403.215 Section 403.215 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL PROVISIONS SPECIAL PROGRAMS AND PROJECTS Medicare Supplemental Policies General Provisions § 403.215 Loss ratio standards. (a) The policy must...

  8. 45 CFR 158.210 - Minimum medical loss ratio.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 45 Public Welfare 1 2011-10-01 2011-10-01 false Minimum medical loss ratio. 158.210 Section 158.210 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES REQUIREMENTS RELATING TO HEALTH CARE ACCESS... § 158.210 Minimum medical loss ratio. Subject to the provisions of § 158.211 of this subpart: (a)...

  9. Riparian Sediment Delivery Ratio: Stiff Diagrams and Artifical Neural Networks

    EPA Science Inventory

    Various methods are used to estimate sediment transport through riparian buffers and grass jilters with the sediment delivery ratio having been the most widely applied. The U.S. Forest Service developed a sediment delivery ratio using the stiff diagram and a logistic curve to int...

  10. Ratio Tables to Promote Proportional Reasonings in the Primary Classroom

    ERIC Educational Resources Information Center

    Dole, Shelley

    2008-01-01

    There are many classroom activities that can be implemented with primary students that introduce and immerse them in ratio investigations. Some enjoyable tasks include finding the ratio of tongue rollers to non-tongue rollers in the classroom; left-hand dominant to right-hand dominant; right-thumb over left-thumb when clasping the hands to…

  11. 26 CFR 26.2642-1 - Inclusion ratio.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 26 Internal Revenue 14 2010-04-01 2010-04-01 false Inclusion ratio. 26.2642-1 Section 26.2642-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) ESTATE AND GIFT TAXES GENERATION-SKIPPING TRANSFER TAX REGULATIONS UNDER THE TAX REFORM ACT OF 1986 § 26.2642-1 Inclusion ratio....

  12. Golden Ratio in a Coupled-Oscillator Problem

    ERIC Educational Resources Information Center

    Moorman, Crystal M.; Goff, John Eric

    2007-01-01

    The golden ratio appears in a classical mechanics coupled-oscillator problem that many undergraduates may not solve. Once the symmetry is broken in a more standard problem, the golden ratio appears. Several student exercises arise from the problem considered in this paper.

  13. A theoretically based determination of bowen-ratio fetch requirements

    USGS Publications Warehouse

    Stannard, D.I.

    1997-01-01

    Determination of fetch requirements for accurate Bowen-ratio measurements of latent- and sensible-heat fluxes is more involved than for eddy-correlation measurements because Bowen-ratio sensors are located at two heights, rather than just one. A simple solution to the diffusion equation is used to derive an expression for Bowen-ratio fetch requirements, downwind of a step change in surface fluxes. These requirements are then compared to eddy-correlation fetch requirements based on the same diffusion equation solution. When the eddy-correlation and upper Bowen-ratio sensor heights are equal, and the available energy upwind and downwind of the step change is constant, the Bowen-ratio method requires less fetch than does eddy correlation. Differences in fetch requirements between the two methods are greatest over relatively smooth surfaces. Bowen-ratio fetch can be reduced significantly by lowering the lower sensor, as well as the upper sensor. The Bowen-ratio fetch model was tested using data from a field experiment where multiple Bowen-ratio systems were deployed simultaneously at various fetches and heights above a field of bermudagrass. Initial comparisons were poor, but improved greatly when the model was modified (and operated numerically) to account for the large roughness of the upwind cotton field.

  14. Auditory discrimination of frequency ratios: the octave singularity.

    PubMed

    Bonnard, Damien; Micheyl, Christophe; Semal, Catherine; Dauman, René; Demany, Laurent

    2013-06-01

    Sensitivity to frequency ratios is essential for the perceptual processing of complex sounds and the appreciation of music. This study assessed the effect of ratio simplicity on ratio discrimination for pure tones presented either simultaneously or sequentially. Each stimulus consisted of four 100-ms pure tones, equally spaced in terms of frequency ratio and presented at a low intensity to limit interactions in the auditory periphery. Listeners had to discriminate between a reference frequency ratio of 0.97 octave (about 1.96:1) and target frequency ratios, which were larger than the reference. In the simultaneous condition, the obtained psychometric functions were nonmonotonic: as the target frequency ratio increased from 0.98 octave to 1.04 octaves, discrimination performance initially increased, then decreased, and then increased again; performance was better when the target was exactly one octave (2:1) than when the target was slightly larger. In the sequential condition, by contrast, the psychometric functions were monotonic and there was no effect of frequency ratio simplicity. A control experiment verified that the non-monotonicity observed in the simultaneous condition did not originate from peripheral interactions between the tones. Our results indicate that simultaneous octaves are recognized as "special" frequency intervals by a mechanism that is insensitive to the sign (positive or negative) of deviations from the octave, whereas this is apparently not the case for sequential octaves.

  15. Parental care and adaptive brood sex ratio manipulation in birds.

    PubMed Central

    Hasselquist, Dennis; Kempenaers, Bart

    2002-01-01

    Under many circumstances, it might be adaptive for parents to bias the investment in offspring in relation to sex. Recently developed molecular techniques that allow sex determination of newly hatched offspring have caused a surge in studies of avian sex allocation. Whether females bias the primary brood sex ratio in relation to factors such as environmental and parental quality is debated. Progress is hampered because the mechanisms for primary sex ratio manipulation are unknown. Moreover, publication bias against non-significant results may distort our view of adaptive sex ratio manipulation. Despite this, there is recent experimental evidence for adaptive brood sex ratio manipulation in birds. Parental care is a particularly likely candidate to affect the brood sex ratio because it can have strong direct effects on the fitness of both parents and their offspring. We investigate and make predictions of factors that can be important for adaptive brood sex ratio manipulation under different patterns of parental care. We encourage correlational studies based on sufficiently large datasets to ensure high statistical power, studies identifying and experimentally altering factors with sex-differential fitness effects that may cause brood sex ratio skew, and studies that experimentally manipulate brood sex ratio and investigate fitness effects. PMID:11958704

  16. The Ratio of Public Investment in Education in China

    ERIC Educational Resources Information Center

    Liu, Zeyun; Yuan, Liansheng

    2007-01-01

    Based on cross-section data worldwide and time series data in China, the essay is intended to make an analysis of the factors which have impacts on the ratio of public investment in education by using econometric models and then the future ratio may be predicted. Conclusions are as follows. First, the proportion of fiscal revenue to GDP (gross…

  17. 45 CFR 158.210 - Minimum medical loss ratio.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 45 Public Welfare 1 2014-10-01 2014-10-01 false Minimum medical loss ratio. 158.210 Section 158.210 Public Welfare Department of Health and Human Services REQUIREMENTS RELATING TO HEALTH CARE ACCESS... § 158.210 Minimum medical loss ratio. Subject to the provisions of § 158.211 of this subpart: (a)...

  18. 45 CFR 158.210 - Minimum medical loss ratio.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 45 Public Welfare 1 2012-10-01 2012-10-01 false Minimum medical loss ratio. 158.210 Section 158.210 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES REQUIREMENTS RELATING TO HEALTH CARE ACCESS... § 158.210 Minimum medical loss ratio. Subject to the provisions of § 158.211 of this subpart: (a)...

  19. Explorations in Statistics: The Analysis of Ratios and Normalized Data

    ERIC Educational Resources Information Center

    Curran-Everett, Douglas

    2013-01-01

    Learning about statistics is a lot like learning about science: the learning is more meaningful if you can actively explore. This ninth installment of "Explorations in Statistics" explores the analysis of ratios and normalized--or standardized--data. As researchers, we compute a ratio--a numerator divided by a denominator--to compute a…

  20. 45 CFR 158.210 - Minimum medical loss ratio.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 45 Public Welfare 1 2013-10-01 2013-10-01 false Minimum medical loss ratio. 158.210 Section 158.210 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES REQUIREMENTS RELATING TO HEALTH CARE ACCESS... § 158.210 Minimum medical loss ratio. Subject to the provisions of § 158.211 of this subpart: (a)...

  1. The Sequential Probability Ratio Test and Binary Item Response Models

    ERIC Educational Resources Information Center

    Nydick, Steven W.

    2014-01-01

    The sequential probability ratio test (SPRT) is a common method for terminating item response theory (IRT)-based adaptive classification tests. To decide whether a classification test should stop, the SPRT compares a simple log-likelihood ratio, based on the classification bound separating two categories, to prespecified critical values. As has…

  2. Site-dependant redox ratio in healthy oral cavity

    NASA Astrophysics Data System (ADS)

    Shanmugam, Sivabalan; Koteeswaran, Dornadula; Aruna, Prakasarao; Ganesan, Singaravelu

    2011-03-01

    The metabolic coenzymes NADH and FAD are autofluorescent and can be monitored non-destructively and without exogenous labels, using optical techniques. These endogenous fluorophores which are present in the cells and tissues gives rise to different fluorescence emission/excitation spectra between the normal and different diseased conditions. In the resent years, finding the optical redox ratio i.e., the ratio of the fluorescence intensity of FAD and NADH, gives the relative change in the oxidation-reduction state of the cells. Unlike other organs oral cavity has lined with variety of mucosal types. We investigated in vivo Optical redox ratio for four different anatomical locations viz., cheek mucosa, vermilion border of the lip, Hard palate, dorsal side of the tongue of healthy oral cavity. We measured this ratio for 20 healthy subjects and the redox ratio was significantly different between the different anatomical locations. The statistical significance was also investigated.

  3. Extreme values of the Poisson's ratio of cubic crystals

    NASA Astrophysics Data System (ADS)

    Epishin, A. I.; Lisovenko, D. S.

    2016-10-01

    The problem of determining the extrema of Poisson's ratio for cubic crystals is considered, and analytical expressions are derived to calculate its extreme values. It follows from the obtained solution that, apart from extreme values at standard orientations, extreme values of Poisson's ratio can also be detected at special orientations deviated from the standard ones. The derived analytical expressions are used to calculate the extreme values of Poisson's ratio for a large number of known cubic crystals. The extremely high values of Poisson's ratio are shown to be characteristic of metastable crystals, such as crystals with the shape memory effect caused by martensitic transformation. These crystals are mainly represented by metallic alloys. For some crystals, the absolute extrema of Poisson's ratio can exceed the standard values, which are-1 for a standard minimum and +2 for a standard maximum.

  4. Observation of Enhanced Transformer Ratio in Collinear Wakefield Acceleration

    NASA Astrophysics Data System (ADS)

    Jing, C.; Kanareykin, A.; Power, J. G.; Conde, M.; Yusof, Z.; Schoessow, P.; Gai, W.

    2007-04-01

    One approach to future high energy particle accelerators is based on the wakefield principle: a leading high-charge drive bunch is used to excite fields in an accelerating structure or plasma that in turn accelerates a trailing low-charge witness bunch. The transformer ratio R is defined as the ratio of the maximum energy gain of the witness bunch to the maximum energy loss of the drive bunch. In general, R<2 for this configuration. A number of techniques have been proposed to overcome the transformer ratio limitation. We report here the first experimental study of the ramped bunch train (RBT) technique in a dielectric based accelerating structure. A single drive bunch was replaced by two bunches with charge ratio of 1∶2.5 and a separation of 10.5 wavelengths of the fundamental mode. An average measured transformer ratio enhancement by a factor of 1.31 over the single drive bunch case was obtained.

  5. Measurement of fatigue crack closure for negative stress ratio

    SciTech Connect

    Romeiro, F.F.J.; Domingos, C.A.; Freitas, M.J.M. de

    1999-07-01

    The concept of fatigue crack closure, introduced in the 60's by Elber, has been used to explain a wide range of positive stress ratio crack propagation results (R {ge} 0). Less attention has been given to fatigue loading for negative stress ratios (R {lt} 0). In this work the results of crack propagation tests of middle-crack tension M(T) specimens of a normalized medium carbon steel DIN Ck 45 for a wide range of stress ratios from 0.7 {ge} R {ge} {minus}3 are presented. Crack closure loads were measured with the compliance technique at test frequency, using a data acquisition system. Negative crack closure loads were found for negative stress ratios R {le} {minus}1, which can explain higher crack propagation rates and accelerations in crack growth during variable-amplitude tests where compressive loads of different stress ratios are present.

  6. Secular trends and geographical variations in sex ratio at birth.

    PubMed

    Pavic, Dario

    2015-12-01

    Numerous studies have established the presence of secular trends and geographical variations in sex ratio at birth, albeit with mixed and often contradictory results. In addition, a multitude of environmental, social, economic, demographic and other factors has been proposed to influence the sex ratio at birth, thus complicating the interpretation of both secular trends and geographical variations. In this paper, the current state of knowledge on these issues is presented and critically assessed. Analyzing longer time series of sex ratio at birth with possible cycles and random components is given priority over establishing simple linear trends in the data. In analyzing the geographical variation in the sex ratio at birth, two different levels of analysis are distinguished (global and local), and two different sets of factors affecting the sex ratio at birth are proposed accordingly. Some key guidelines and future research directions are also proposed.

  7. The C-12/C-13 Ratio as a Chemistry Indicator

    NASA Technical Reports Server (NTRS)

    Wirstroem, Eva; Geppert, Wolf; Persson, Carina; Charnley, Steven

    2011-01-01

    Isotopic ratios of elements are considered powerful tools, e.g. in tracing the origin of solar system body materials, or the degree of nucleosynthesis processing throughout the Galaxy. In interstellar molecules, some isotopic ratios like H/D and C-12/C-13 can also be used as indicators of their chemical origin. Isotope fractionation in gas-phase chemical reactions and gas-dust interaction makes observations of the ratio between C-12 and C-13 isotopologues suitable to distinguish between different formation scenarios. We will present observations of the C-12/C-13 ratio in methanol and formaldehyde towards a sample of embedded, massive young stellar objects. In relation to this we also present results from theoretical modeling showing the usefulness of the C-12/C-13 ratio as a chemistry indicator.

  8. Metal [100] Nanowires with Negative Poisson’s Ratio

    PubMed Central

    Ho, Duc Tam; Kwon, Soon-Yong; Kim, Sung Youb

    2016-01-01

    When materials are under stretching, occurrence of lateral contraction of materials is commonly observed. This is because Poisson’s ratio, the quantity describes the relationship between a lateral strain and applied strain, is positive for nearly all materials. There are some reported structures and materials having negative Poisson’s ratio. However, most of them are at macroscale, and reentrant structures and rigid rotating units are the main mechanisms for their negative Poisson’s ratio behavior. Here, with numerical and theoretical evidence, we show that metal [100] nanowires with asymmetric cross-sections such as rectangle or ellipse can exhibit negative Poisson’s ratio behavior. Furthermore, the negative Poisson’s ratio behavior can be further improved by introducing a hole inside the asymmetric nanowires. We show that the surface effect inducing the asymmetric stresses inside the nanowires is a main origin of the superior property. PMID:27282358

  9. Sex ratio dynamics and fluctuating selection on personality.

    PubMed

    Del Giudice, Marco

    2012-03-21

    Fluctuating selection has often been proposed as an explanation for the maintenance of genetic variation in personality. Here I argue that the temporal dynamics of the sex ratio can be a powerful source of fluctuating selection on personality traits, and develop this hypothesis with respect to humans. First, I review evidence that sex ratios modulate a wide range of social processes related to mating and parenting. Since most personality traits affect mating and parenting behavior, changes in the sex ratio can be expected to result in variable selection on personality. I then show that the temporal dynamics of the sex ratio are intrinsically characterized by fluctuations at various timescales. Finally, I address a number of evolutionary genetic challenges to the hypothesis. I conclude that the sex ratio hypothesis is a plausible explanation of genetic variation in human personality, and may be fruitfully applied to other species as well.

  10. Analysis of web height ratios according to age and sex.

    PubMed

    Sari, Elif

    2015-06-01

    Each component of the web space, a three-dimensional structure, should be carefully created during reconstruction of web space loss. One of these web space components is the web height. In this study, the dorsal view of subjects' hands was analyzed to determine the web height ratios. The web height ratios were then compared with respect to age and sex. The second and third web height ratios differed between adult men and women and between children and adults. However, no differences were observed among children. This study is unique because it focuses on the web height ratios of all web spaces according to age and sex and provides a very easy-to-use scale that may help surgeons to perform web space reconstruction. Moreover, the present study adds to the literature by providing information on the first web height ratios of the hand.

  11. Effect of primary-zone equivalence ratio on pollutant formation

    NASA Technical Reports Server (NTRS)

    Claus, R. W.

    1979-01-01

    Test were conducted to determine the effect of primary-zone equivalence ratio on the formation of smoke and other gaseous pollutants in an experimental can combustor. Several fuel injection techniques were examined at primary-zone equivalence ratios from 0.8 to 2.0. The main emphasis was on reducing fuel-rich-combustion smoke levels. Two of the four fuel injection configurations studied produced smoke levels below a smoke number of 20 at a primary-zone equivalence ratio of about 1.7. As the fuel mixing and atomization were recorded at primary-zone equivalence ratios as high as 2.0. The gaseous emissions of unburned hydrocarbons, carbon monoxide, and oxides of nitrogen were quite sensitive to the fuel injection configuration as well as to the primary-zone equilvalence ratio.

  12. Deformation mechanisms in negative Poisson's ratio materials - Structural aspects

    NASA Technical Reports Server (NTRS)

    Lakes, R.

    1991-01-01

    Poisson's ratio in materials is governed by the following aspects of the microstructure: the presence of rotational degrees of freedom, non-affine deformation kinematics, or anisotropic structure. Several structural models are examined. The non-affine kinematics are seen to be essential for the production of negative Poisson's ratios for isotropic materials containing central force linkages of positive stiffness. Non-central forces combined with pre-load can also give rise to a negative Poisson's ratio in isotropic materials. A chiral microstructure with non-central force interaction or non-affine deformation can also exhibit a negative Poisson's ratio. Toughness and damage resistance in these materials may be affected by the Poisson's ratio itself, as well as by generalized continuum aspects associated with the microstructure.

  13. Implications of the Nitrogen Isotope Ratio in Titan's Atmosphere for the Nitrogen Ratio in Ammonia in Comets

    NASA Astrophysics Data System (ADS)

    Mandt, K.; Mousis, O.

    2013-12-01

    The D/H ratio of water measured in solar system bodies has been established as a tool for determining the conditions under which bodies such as comets or icy moons formed. This ratio varies significantly and indicates complex thermal and chemical evolution of the solar nebula during solar system and planetary formation. Nitrogen isotope ratios also vary significantly, and in some but not all cases correlate to D/H ratios, but are poorly understood. Nitrogen in the solar nebula was primarily in the form of atomic and molecular nitrogen. The isotope ratio (14N/15N) of this reservoir is expected to be ~435 based on the ratio measured in Jupiter's atmosphere, because the atmosphere of Jupiter is made up of gas captured from the solar nebula (Owen et al., 2001). The terrestrial atmospheric ratio is 272, which is close to the ratio measured in the Earth's mantle. This may be the primordial ratio for nitrogen delivered to Earth depending on the amount of exchange between the atmosphere and the mantle and any atmospheric fractionation processes that may have influenced the ratio over time. Comets are a possible source of nitrogen in the Earth's atmosphere (Hutsmekers et al., 2009), although chondrites have also been suggested as a source (Marty, 2012). In the case of comets, nitrogen would have been essentially retained in the form of ammonia (Mousis et al., 2012), which is the most abundant form of nitrogen in comets. The nitrogen in Titan's atmosphere is expected to have originated as ammonia hydrates and converted to N2 early in Titan's history (Atreya et al., 1978). The nitrogen ratio in Titan's atmosphere is ~170, which is significantly enriched in the heavy isotope compared to the terrestrial value. We will discuss the evolution of the nitrogen ratio in Titan's atmosphere (Mandt et al., 2009), the limits of the primordial ratio in ammonia, and the implications for this ratio for the isotope ratio in ammonia in comets that should be measured by the ROSINA instrument

  14. Aerodynamic Properties of Rough Surfaces with High Aspect-Ratio Roughness Elements: Effect of Aspect Ratio and Arrangements

    NASA Astrophysics Data System (ADS)

    Sadique, Jasim; Yang, Xiang I. A.; Meneveau, Charles; Mittal, Rajat

    2016-12-01

    We examine the effect of varying roughness-element aspect ratio on the mean velocity distributions of turbulent flow over arrays of rectangular-prism-shaped elements. Large-eddy simulations (LES) in conjunction with a sharp-interface immersed boundary method are used to simulate spatially-growing turbulent boundary layers over these rough surfaces. Arrays of aligned and staggered rectangular roughness elements with aspect ratio >1 are considered. First the temporally- and spatially-averaged velocity profiles are used to illustrate the aspect-ratio effects. For aligned prisms, the roughness length (z_o ) and the friction velocity (u_* ) increase initially with an increase in the roughness-element aspect ratio, until the values reach a plateau at a particular aspect ratio. The exact value of this aspect ratio depends on the coverage density. Further increase in the aspect ratio changes neither z_o , u_* nor the bulk flow above the roughness elements. For the staggered cases, z_o and u_* continue to increase for the surface coverage density and the aspect ratios investigated. To model the flow response to variations in roughness aspect ratio, we turn to a previously developed phenomenological volumetric sheltering model (Yang et al., in J Fluid Mech 789:127-165, 2016), which was intended for low to moderate aspect-ratio roughness elements. Here, we extend this model to account for high aspect-ratio roughness elements. We find that for aligned cases, the model predicts strong mutual sheltering among the roughness elements, while the effect is much weaker for staggered cases. The model-predicted z_o and u_* agree well with the LES results. Results show that the model, which takes explicit account of the mutual sheltering effects, provides a rapid and reliable prediction method of roughness effects in turbulent boundary-layer flows over arrays of rectangular-prism roughness elements.

  15. Stable isotope ratio determination of the origin of vanillin in vanilla extracts and its relationship to vanillin/potassium ratios

    SciTech Connect

    Martin, G.E.; Alfonso, F.C.; Figert, D.M.; Burggraff, J.M.

    1981-09-01

    A method is described for isolating vanillin from vanilla extract, followed by stable isotope ratio analysis to determine the amount of natural vanillin contained in adulterated vanilla extracts. After the potassium content is determined, the percent Madagascar and/or Java vanilla beans incorporated into the extract may then be approximated from the vanillin/potassium ratio.

  16. Effect of timing of artificial insemination on sex ratio.

    PubMed

    Rorie, R W

    1999-12-01

    For a number of years, the time of insemination or mating during estrus has been believed to influence the sex ratio of offspring, with early insemination resulting in more females and late insemination, more males. Possible mechanisms of altering the sex ratio include facilitating or inhibiting the transport of either X- or Y-chromosome-bearing sperm through the reproductive tract, preferential selection of sperm at fertilization, or sex-specific death of embryos after fertilization. In livestock species, there is evidence for preferential selection of X- or Y-bearing sperm, based on the maturational state of the oocyte at fertilization. In deer and sheep, early and late insemination appears to skew the sex ratio toward females and males, respectively. In cattle, conflicting reports on the effect of time of insemination on sex ratio make the premise less clear. Many of the published studies lack adequate observations for definitive conclusions and/or are based on infrequent observations of estrus, making it difficult to assess the effect of time of insemination on sex ratio. It is likely that any effect of time of insemination on sex ratio in cattle is relatively small. Evidence is accumulating that treatments used for synchronization of estrus or ovulation in cattle may influence the sex ratio.

  17. Time Evolution of Elemental Ratios in Solar Energetic Particle Events

    NASA Astrophysics Data System (ADS)

    Zelina, P.; Dalla, S.; Cohen, C. M. S.; Mewaldt, R. A.

    2017-01-01

    Heavy ion ratio abundances in solar energetic particle (SEP) events, e.g., Fe/O, often exhibit decreases over time. Using particle instruments on the Advanced Composition Explorer, Solar and Heliospheric Observatory and Solar Terrestrial Relations Observatory spacecraft, we analyzed heavy ion data from 4 SEP events taking place between 2006 December and 2014 December. We constructed 36 different ionic pairs and studied their time evolution in each event. We quantified the temporal behavior of abundant SEP ratios by fitting the data to derive a decay time constant B. We also considered the ratio of ionic mass-to-charge for each pair, the S value given, e.g., for Fe/O by {S}{Fe/{{O}}}={(M/Q)}{Fe}/{(M/Q)}{{O}}. We found that the temporal behavior of SEP ratios is ordered by the value of S: ratios with S> 1 showed decreases over time (i.e., B< 0) and those with S< 1 showed increases (B> 0). We plotted B as a function of S and observed a clear monotonic dependence: ratios with a large S decayed at a higher rate. A prominent discontinuity at S = 2.0 (corresponding to He/H) was found in three of the four events, suggesting anomalous behavior of protons. The X/H ratios often show an initial increase followed by a decrease, and decay at a slower rate. We discuss possible causes of the observed B versus S trends within current understanding of SEP propagation.

  18. Effects of spatial resolution ratio in image fusion

    USGS Publications Warehouse

    Ling, Y.; Ehlers, M.; Usery, E.L.; Madden, M.

    2008-01-01

    In image fusion, the spatial resolution ratio can be defined as the ratio between the spatial resolution of the high-resolution panchromatic image and that of the low-resolution multispectral image. This paper attempts to assess the effects of the spatial resolution ratio of the input images on the quality of the fused image. Experimental results indicate that a spatial resolution ratio of 1:10 or higher is desired for optimal multisensor image fusion provided the input panchromatic image is not downsampled to a coarser resolution. Due to the synthetic pixels generated from resampling, the quality of the fused image decreases as the spatial resolution ratio decreases (e.g. from 1:10 to 1:30). However, even with a spatial resolution ratio as small as 1:30, the quality of the fused image is still better than the original multispectral image alone for feature interpretation. In cases where the spatial resolution ratio is too small (e.g. 1:30), to obtain better spectral integrity of the fused image, one may downsample the input high-resolution panchromatic image to a slightly lower resolution before fusing it with the multispectral image.

  19. Population abundance and sex ratio in dioecious helminth parasites.

    PubMed

    Poulin, Robert

    1997-07-01

    Parasite populations are highly fragmented in space and time, and consist of aggregates of genetically similar individuals sharing the same host. To avoid inbreeding, theory predicts that female-biased sex ratios should be strongly favoured when either or both prevalence and intensity of infection are low. Other models indicate that if sex ratios are selected to increase the probability of mating, they should be less biased at a high intensity of infection in polygamous parasites, since at high intensities all females are mated. To test these predictions, the relationship between sex ratio and both the prevalence and intensity of infection was examined in comparative studies across 193 populations of nematode and acanthocephalan parasites. Sex ratios in these two dioecious, polygamous taxa are usually female biased. Among natural populations, no significant relationship was observed once the confounding effects of phylogeny had been removed. However, among experimental populations of nematodes, a negative relationship was found between intensity of infection and sex ratio, even after controlling for phylogeny. In other words, at high intensities, populations of nematodes are less female biased. This result must be treated with caution because of the unusually high numbers of worms per host in experimental infections. Nevertheless, combined with information on the proximate mechanisms regulating sex ratios in these parasites, it suggests a link between the characteristics of parasite populations and their sex ratio.

  20. Sign-tunable Poisson's ratio in semi-fluorinated graphene.

    PubMed

    Qin, Rui; Zheng, Jiaxin; Zhu, Wenjun

    2017-01-07

    Poisson's ratio is a fundamental property of a material which reflects the transverse strain response to the applied axial strain. Negative Poisson's ratio is allowed theoretically, but is rare in nature. Besides the discovery and tailoring of bulk auxetic materials, recent studies have also found a negative Poisson's ratio in nanomaterials, while their negative Poisson's ratio is mainly based on conventional rigid mechanical models as bulk auxetic materials. In this work, we report the existence of in-plane negative Poisson's ratio in a two-dimensional convex structure of newly synthesized semi-fluorinated graphene by using first-principles calculations. In addition, the sign of the Poisson's ratio can be tuned by the applied strain. Interestingly, we find that this unconventional negative Poisson's ratio cannot be explained by conventional rigid mechanical models but originates from the enhanced bond angle strain over the bond strain due to chemical functionalization. This new mechanism of auxetics extends the scope of auxetic nanomaterials and can serve as design principles for future discovery and design of new auxetic materials.

  1. Patterns of Family Formation in Response to Sex Ratio Variation

    PubMed Central

    Schacht, Ryan; Kramer, Karen L.

    2016-01-01

    The impact that unbalanced sex ratios have on health and societal outcomes is of mounting contemporary concern. However, it is increasingly unclear whether it is male- or female-biased sex ratios that are associated with family and social instability. From a socio-demographic perspective, male-biased sex ratios leave many men unable to find a mate, elevating competition among males, disrupting family formation and negatively affecting social stability. In contrast, from a mating-market perspective, males are expected to be less willing to marry and commit to a family when the sex ratio is female-biased and males are rare. Here we use U.S. data to evaluate predictions from these competing frameworks by testing the relationship between the adult sex ratio and measures of family formation. We find that when women are rare men are more likely to marry, be part of a family and be sexually committed to a single partner. Our results do not support claims that male-biased sex ratios lead to negative family outcomes due to a surplus of unmarried men. Rather, our results highlight the need to pay increased attention to female-biased sex ratios. PMID:27556401

  2. The Romberg ratio in people with multiple sclerosis.

    PubMed

    Kalron, Alon

    2017-03-14

    Postural control relies on the integration of inputs from the visual, somatosensory and vestibular systems which are frequently impaired in people with Multiple Sclerosis (PwMS). In this situation, examining the Romberg ratio can be useful. This parameter can be interpreted as a gross indicator of a vestibular and proprioceptive contribution to postural control. Therefore, the primary objective of the current study was to examine whether the Romberg ratio differs between MS fallers, non-fallers and neurological disability levels. In addition, we clarified the association between the Romberg ratio values with validated gait and the balance tests in PwMS. Romberg ratio values were calculated according to the sway rate, total sway area and center of pressure (CoP) path length. The patient group included 542 PwMS (337 women) with a mean age of 42.3 (S.D=13.8). In terms of fall status, significant differences were observed between the faller (n=287) and non-faller (n=255) groups solely in terms of the Romberg ratio-ellipse sway area: 2.76 (S.D=2.46) vs. 2.24 (S.D=2.01), P-value=0.01. A significant increase in the Romberg ratio was found between the severe group (n=50), the very mild (n=245), mild (n=186) and moderate (n=61) groups for each of the three Romberg ratio quotients. Significant weak correlation scores were found between the Romberg ratio-ellipse sway area and all walking and balance outcome measures; the Pearson's rho ranged from 0.172 to 0.270. The present data suggest that an elevated Romberg ratio quotient, especially according to the sway area, is an indicator of poor walking and balance capabilities in PwMS.

  3. Measurement of the temperature coefficient of ratio transformers

    NASA Technical Reports Server (NTRS)

    Briggs, Matthew E.; Gammon, Robert W.; Shaumeyer, J. N.

    1993-01-01

    We have measured the temperature coefficient of the output of several ratio transformers at ratios near 0.500,000 using an ac bridge and a dual-phase, lock-in amplifier. The two orthogonal output components were each resolved to +/- ppb of the bridge drive signal. The results for three commercial ratio transformers between 20 and 50 C range from 0.5 to 100 ppb/K for the signal component in phase with the bridge drive, and from 4 to 300 ppb/K for the quadrature component.

  4. The H-alpha/H-beta ratio in solar flares

    NASA Technical Reports Server (NTRS)

    Zirin, H.; Liggett, M.; Patterson, A.

    1982-01-01

    The present investigation involves the study of an extensive body of data accumulated of simultaneous H-alpha and H-beta cinematography of flares. The data were obtained with two telescopes simultaneously photographing flares in H-alpha and H-beta. The results of measurements in a number of flares are presented in a table. The flares were selected purely by optical quality of the data. That the measured ratios are not too different from those in stellar flares is suggested by the last two columns of the table. These columns show that a variety of possible line width ratios could give an integrated intensity ratio of less than unity.

  5. Frequency ratios and the perception of tone patterns.

    PubMed

    Schellenberg, E G; Trehub, S E

    1994-06-01

    We quantified the relative simplicity of frequency ratios and reanalyzed data from several studies on the perception of simultaneous and sequential tones. Simplicity of frequency ratios accounted for judgments of consonance and dissonance and for judgments of similarity across a wide range of tasks and listeners. It also accounted for the relative ease of discriminating tone patterns by musically experienced and inexperienced listeners. These findings confirm the generality of previous suggestions of perceptual processing advantages for pairs of tones related by simple frequency ratios.

  6. Comments on D/H ratios in chondritic organic matter

    NASA Astrophysics Data System (ADS)

    Smith, J. W.; Rigby, D.

    1981-06-01

    D/H ratios in chondritic organic matter are investigated. Demineralized organic residues obtained from previous experiments were dried in a quartz reaction vessel under vacuum for 60 minutes at 250-300 C and then combusted in oxygen for 20 minutes at 850 C. The apparatus is described and the results of the experiments such as D/H ratios in water and measurements on total carbon dioxide are given. Atomic H/C ratios calculated directly from the quantities of carbon dioxide and water recovered, are reported according to Standard Mean Ocean Water and Pee Dee Belemnite, using the customary notation.

  7. Nestling sex ratios in the southwestern willow flycatcher

    USGS Publications Warehouse

    Paxton, E.H.; Sogge, M.K.; McCarthey, Tracy; Keim, Paul

    2002-01-01

    Using molecular-genetic techniques, we determined the gender of 202 Southwestern Willow Flycatcher (Empidonax traillii extimus) nestlings from 95 nests sampled over a five-year period. Overall nestling sex ratio did not vary significantly from 50:50 among years, by clutch order, or by mating strategy (monogamous vs. polygamous pairings). However, we did observe significant differences among the four sites sampled, with sex ratios biased either toward males or females at the different sites. Given the small population sizes and geographic isolation of many of the endangered subspecies' breeding populations, sex-ratio differences may have localized negative impacts.

  8. Nestling sex ratio in the Southwestern Willow Flycatcher

    USGS Publications Warehouse

    Paxton, E.H.; Sogge, M.K.; McCarthey, T.D.; Keim, P.

    2002-01-01

    Using molecular-genetic techniques, we determined the gender of 202 Southwestern Willow Flycatcher (Empidonax traillii extimus) nestlings from 95 nests sampled over a five-year period. Overall nestling sex ratio did not vary significantly from 50:50 among years, by clutch order, or by mating strategy (monogamous vs. polygamous pairings). However, we did observe significant differences among the four sites sampled, with sex ratios biased either toward males or females at the different sites. Given the small population sizes and geographic isolation of many of the endangered subspecies' breeding populations, sex-ratio differences may have localized negative impacts. ?? The Cooper Ornithological Society 2002.

  9. Poisson's Ratios and Volume Changes for Plastically Orthotropic Material

    NASA Technical Reports Server (NTRS)

    Stowell, Elbridge Z; Pride, Richard A

    1956-01-01

    Measurements of Poisson's ratios have been made in three orthogonal directions on aluminum alloy blocks in compression and on stainless-steel sheet in both tension and compression. These measurements, as well as those obtained by density determinations, show that there is no permanent plastic change in volume within the accuracy of observation. A method is suggested whereby a correlation may be effected between the measured individual values of the Poisson's ratios and the stress-strain curves for the material. Allowance must be made for the difference in the stress-strain in tension and compression; this difference, wherever it appears, is accompanied by significant changes in the Poisson's ratios.

  10. How required reserve ratio affects distribution and velocity of money

    NASA Astrophysics Data System (ADS)

    Xi, Ning; Ding, Ning; Wang, Yougui

    2005-11-01

    In this paper the dependence of wealth distribution and the velocity of money on the required reserve ratio is examined based on a random transfer model of money and computer simulations. A fractional reserve banking system is introduced to the model where money creation can be achieved by bank loans and the monetary aggregate is determined by the monetary base and the required reserve ratio. It is shown that monetary wealth follows asymmetric Laplace distribution and latency time of money follows exponential distribution. The expression of monetary wealth distribution and that of the velocity of money in terms of the required reserve ratio are presented in a good agreement with simulation results.

  11. Patterns in small aspect ratio Bénard-Marangoni convection.

    PubMed

    Ramón, M L; Maza, D; Mancini, H L

    1999-10-01

    An experimental study of pattern formation in Bénard-Marangoni convection with small aspect ratio containers and high Prandtl number fluids is presented. The observed stationary patterns complete previous experimental works performed at different values of aspect ratio and supercriticality. Detailed experimental studies of the flow in some single structures are described, and spatial bifurcations between different stationary planforms for a fixed aspect ratio are shown. These experimental results agree qualitatively with linear theory analysis and with some previous numerical works about boundary conditions effects.

  12. Transmittance ratio constrained retrieval technique for lidar cirrus measurements.

    PubMed

    Su, Jia; McCormick, M Patrick; Liu, Zhaoyan; Lee, Robert B; Leavor, Kevin R; Lei, Liqiao

    2012-05-01

    This letter describes a lidar retrieval technique that uses the transmittance ratio as a constraint to determine an average lidar ratio as well as extinction and backscatter coefficients of transparent cirrus clouds. The cloud transmittance ratio is directly obtained from two adjacent elastic lidar backscatter signals. The technique can be applied to cirrus measurements where neither the molecular scattering dominant signals above and below the cloud layer are found nor cloudfree reference profiles are available. The technique has been tested with simulated lidar signals and applied to backscatter lidar measurements at Hampton University, Hampton, Virginia.

  13. On the ability to directly evaluate sensory ratios.

    PubMed

    Masin, Sergio Cesare

    2013-01-01

    The study explored whether participants could directly evaluate sensory ratios. The results indicate that they did not exhibit this ability for the extensive continuum of length and the intensive continua of brightness and brightness difference. Functional measurement analysis, combined with a chronometric analysis of responses, indicated that participants used mental counting for length and used difference evaluation for brightness and brightness difference. The finding that participants evaluated brightness differences under instructions to evaluate brightness ratios suggests that difference judgments may be a general human capability. It resolves questions raised by prior tests of Torgerson's conjecture and by prior consistency tests of ratio evaluation.

  14. Secondary to primary ratio and the continuous acceleration

    NASA Technical Reports Server (NTRS)

    Giler, M.; Szabelska, B.; Wdowczyk, J.; Wolfendale, A. W.

    1985-01-01

    A general formula for the sec/prim ratio, independently of any details of the propagation and acceleration model is presented. In the limit of equal fragmentation paths for primaries and secondaries, this ratio at a given momentum nucleon is proportional only to the mean path of the observed primaries at that moment. It is shown that it is unlikely to get a decreasing sec/prim ratio with energy if an acceleration process takes place during particle propagation in the interstellar medium (ISM).

  15. Secondary to primary ratio and the continuous acceleration

    NASA Astrophysics Data System (ADS)

    Giler, M.; Szabelska, B.; Wdowczyk, J.; Wolfendale, A. W.

    1985-08-01

    A general formula for the sec/prim ratio, independently of any details of the propagation and acceleration model is presented. In the limit of equal fragmentation paths for primaries and secondaries, this ratio at a given momentum nucleon is proportional only to the mean path of the observed primaries at that moment. It is shown that it is unlikely to get a decreasing sec/prim ratio with energy if an acceleration process takes place during particle propagation in the interstellar medium (ISM).

  16. Efficiency of nonstandard and high contact ratio involute spur gears

    NASA Technical Reports Server (NTRS)

    Anderson, N. E.; Loewenthal, S. H.

    1984-01-01

    A power loss prediction was extended to include involute spur gears of nonstandard proportions. The method is used to analyze the effects of modified addendum, tooth thickness, and gear center distance in addition to the parameters previously considered which included gear diameter, pitch, pressure angle, face width, oil viscosity, speed, and torque. Particular emphasis was placed on high contact ratio gearing (contact ratios greater than two). Despite their higher sliding velocities, high contact ratio gears are designed to levels of efficiency comparable to those of conventional gears while retaining their advantages through proper selection of gear geometry.

  17. Efficiency of nonstandard and high contact ratio involute spur gears

    NASA Technical Reports Server (NTRS)

    Anderson, N. E.; Loewenthal, S. H.

    1986-01-01

    A power loss prediction was extended to include involute spur gears of nonstandard proportions. The method is used to analyze the effects of modified addendum, tooth thickness, and gear center distance in addition to the parameters previously considered which included gear diameter, pitch, pressure angle, face width, oil viscosity, speed, and torque. Particular emphasis was placed on high contact ratio gearing (contact ratios greater than two). Despite their higher sliding velocities, high contact ratio gears are designed to levels of efficiency comparable to those of conventional gears while retaining their advantages through proper selection of gear geometry.

  18. Investigation into stutter ratio variability between different laboratories.

    PubMed

    Bright, Jo-Anne; Curran, James M

    2014-11-01

    The determination of parameters such as stutter ratio is important to inform a laboratory's forensic DNA profile interpretation strategy. As part of a large data analysis project to implement a continuous model of DNA profile interpretation we analysed stutter ratio data from eight different forensic laboratories for the Promega PowerPlex(®) 21 multiplex. This allowed a comparison of inter laboratory variation. The maximum difference for any one laboratory from the average of the best fit determined by the model was 0.31%. These results indicate that stutter ratios calculated from samples analysed using the same profiling kit are not expected to differ between laboratories, even those using different capillary electrophoresis platforms. A common set of laboratory parameters are able to be generated and used for profile interpretation at all laboratories using the same multiplex and cycle number, potentially reducing the need for individual laboratories to determine stutter ratios.

  19. Further Developments in Beta-Gamma to Alpha Ratios.

    PubMed

    Smith, David L

    2017-04-01

    An emphasis on alpha-emitting nuclides at nuclear power plants has produced methods for assessing the relative hazard of alpha versus other species. From the relative hazards, or ratios, decisions on the level of effort for worker protection and monitoring are made. The Electric Power Research Institute (EPRI) has issued technical guidance on relative alpha hazard and action level beta-gamma to alpha ratios. This paper shows the development of the ratio concept from first principles and brings hard-to-detect species into consideration. Outcomes from the exercise of computational forms of the ratios are compared to the EPRI results and the differences are noted. Some discussion of the implications and advantages of the developed forms then follows.

  20. Correlation between supercooled liquid relaxation and glass Poisson's ratio

    NASA Astrophysics Data System (ADS)

    Sun, Qijing; Hu, Lina; Zhou, Chao; Zheng, Haijiao; Yue, Yuanzheng

    2015-10-01

    We report on a correlation between the supercooled liquid (SL) relaxation and glass Poisson's ratio (v) by comparing the activation energy ratio (r) of the α and the slow β relaxations and the v values for both metallic and nonmetallic glasses. Poisson's ratio v generally increases with an increase in the ratio r and this relation can be described by the empirical function v = 0.5 - A*exp(-B*r), where A and B are constants. This correlation might imply that glass plasticity is associated with the competition between the α and the slow β relaxations in SLs. The underlying physics of this correlation lies in the heredity of the structural heterogeneity from liquid to glass. This work gives insights into both the microscopic mechanism of glass deformation through the SL dynamics and the complex structural evolution during liquid-glass transition.

  1. Sibling sex ratio of boys with gender identity disorder.

    PubMed

    Zucker, K J; Green, R; Coates, S; Zuger, B; Cohen-Kettenis, P T; Zecca, G M; Lertora, V; Money, J; Hahn-Burke, S; Bradley, S J; Blanchard, R

    1997-07-01

    Sibling sex ratio (the ratio of brothers to sisters) was calculated for 444 boys with gender identity disorder (or with behaviors consistent with this diagnosis). The probands were ascertained from several researchers with expertise with this disorder and from the English language case report literature between 1938 and 1995. Among the probands with at least one sibling (N = 333), the results showed that boys with gender identity disorder had a significant excess of brothers to sisters, 131.1:100, when compared with the expected secondary sex ratio of 106:100. The excess of brothers replicated a previous study by Blanchard, Zucker, Bradley, and Hume (1995), in which the sibling sex ratio was 140.6:100. Further analyses showed that the probands were born later relative to their brothers than they were relative to their sisters. These findings are amenable to several psychosocial and biological explanations, which require further investigation.

  2. Negative Poisson's ratios for extreme states of matter

    PubMed

    Baughman; Dantas; Stafstrom; Zakhidov; Mitchell; Dubin

    2000-06-16

    Negative Poisson's ratios are predicted for body-centered-cubic phases that likely exist in white dwarf cores and neutron star outer crusts, as well as those found for vacuumlike ion crystals, plasma dust crystals, and colloidal crystals (including certain virus crystals). The existence of this counterintuitive property, which means that a material laterally expands when stretched, is experimentally demonstrated for very low density crystals of trapped ions. At very high densities, the large predicted negative and positive Poisson's ratios might be important for understanding the asteroseismology of neutron stars and white dwarfs and the effect of stellar stresses on nuclear reaction rates. Giant Poisson's ratios are both predicted and observed for highly strained coulombic photonic crystals, suggesting possible applications of large, tunable Poisson's ratios for photonic crystal devices.

  3. Stress Ratio Effect on Ratcheting Behavior of AISI 4340 Steel

    NASA Astrophysics Data System (ADS)

    Divya Bharathi, K.; Dutta, K.

    2016-02-01

    Ratcheting is known as accumulation of plastic strain during asymmetric cyclic loading of metallic materials under non-zero mean stress. This phenomenon reduces fatigue life of engineering materials and thus limits the life prediction capacity of Coffin-Manson relationship. This study intends to investigate the ratcheting behavior in AISI 4340 steel which is mainly used for designing of railway wheel sets, axles, shafts, aircraft components and other machinery parts. The effect of stress ratio on the ratcheting behaviour in both annealed and normalised conditions were investigated for investigated steel. Ratcheting tests were done at different stress ratios of -0.4, -0.6 and -0.8. The results showed that the material responds to hardening behavior and nature of strain accumulation is dependent on the magnitude of stress ratio. The post ratcheted samples showed increase in tensile strength and hardness which increases with increasing stress ratio and these variations in tensile properties are correlated with the induced cyclic hardening.

  4. Ratio method of measuring the W boson mass

    NASA Astrophysics Data System (ADS)

    Guo, Feng

    This dissertation describes an alternative method of measuring the W boson mass in DO experiment. Instead of extracting MW from the fitting of W → enu fast Monte Carlo simulations to W → enu data as in the standard method, we make the direct fit of transverse mass between W → enu data and Z → ee data. One of the two electrons from Z boson is treated as a neutrino in the calculation of transverse mass. In ratio method, the best fitted scale factor corresponds to the ratio of W and Z boson mass (MW/M Z). Given the precisely measured Z boson mass, W mass is directly fitted from W → enu and Z → ee data. This dissertation demonstrates that ratio method is a plausible method of measuring the W boson mass. With the 1 fb--1 DO Run IIa dataset, ratio method gives MW = 80435 +/- 43(stat) +/- 26(sys)MeV.

  5. Lipoprotein ratios: Physiological significance and clinical usefulness in cardiovascular prevention

    PubMed Central

    Millán, Jesús; Pintó, Xavier; Muñoz, Anna; Zúñiga, Manuel; Rubiés-Prat, Joan; Pallardo, Luis Felipe; Masana, Luis; Mangas, Alipio; Hernández-Mijares, Antonio; González-Santos, Pedro; Ascaso, Juan F; Pedro-Botet, Juan

    2009-01-01

    Low-density lipoprotein (LDL) cholesterol concentration has been the prime index of cardiovascular disease risk and the main target for therapy. However, several lipoprotein ratios or “atherogenic indices” have been defined in an attempt to optimize the predictive capacity of the lipid profile. In this review, we summarize their pathophysiological aspects, and highlight the rationale for using these lipoprotein ratios as cardiovascular risk factors in clinical practice, specifying their cut-off risk levels and a target for lipid-lowering therapy. Total/high-density lipoprotein (HDL) cholesterol and LDL/HDL cholesterol ratios are risk indicators with greater predictive value than isolated parameters used independently, particularly LDL. Future recommendations regarding the diagnosis and treatment of dyslipidemia, including instruments for calculating cardiovascular risk or action guidelines, should include the lipoprotein ratios with greater predictive power which, in view of the evidence-based results, are none other than those which include HDL cholesterol. PMID:19774217

  6. The choking pressure ratio of a critical flow venturi

    NASA Technical Reports Server (NTRS)

    Hillbrath, H. S.; Dill, W. P.; Wacker, W. A.

    1973-01-01

    The critical flow venturi has many important applications in the measurement and control of gas flow. In many of these applications, it is desirable to minimize the pressure loss required to maintain critical flow conditions. The performance of the venturi may be characterized by the ratio of outlet static pressure to inlet total pressure just sufficiently small to produce critical flow. This ratio is called choking pressure ratio. The optimization of diffusers for critical flow venturis is discussed and suggestions for designs practice are presented. Test results are given for six different diffuser configurations, and a comparison is made with data on 11 configurations from other investigators. It is shown that, for the small divergence angles considered, a simply defined diffuser effectiveness parameter is approximately independent of flow conditions and may be used to predict choking pressure ratio.

  7. ENANTIOMERIC RATIOS OF CHIRAL PCB ATROPISOMERS IN RADIODATED SEDIMENT CORES

    EPA Science Inventory

    Enantiomeric ratios (ERs)) of chiral polychlorinated biphenyl (PCB) atropisomers were quantified in radiodated sediment cores of Lake Hartwell SC, a reservoir heavily impacted by PCBS, to study spatial and temporal changes in chirality. A chiral analysis of cores showed accumulat...

  8. Electrophysiological ratio markers for the balance between reward and punishment.

    PubMed

    Schutter, Dennis J L G; Van Honk, Jack

    2005-08-01

    It has been argued that prototypical forms of psychopathology result from an imbalance in reward and punishment systems. Recent studies suggest that the ratios between slower and faster waves of the electroencephalogram (EEG) index this motivational balance and might therefore have diagnostic value for psychopathology. To scrutinize this notion, the present study investigated whether resting state EEG ratios would predict decision making on the Iowa gambling task (Iowa-GT), a well-known marker for motivational imbalance. A resting state EEG recording was acquired followed by the Iowa-GT in twenty-eight healthy right-handed volunteers. Results showed that higher versus lower EEG ratios were associated with disadvantageous versus advantageous decision making strategies indicating motivational imbalances in reward- and punishment-driven behavior, respectively. This finding provides the first direct evidence that the electrophysiologically derived EEG ratios can serve as biological markers for balance and imbalance in motivation.

  9. Determining Molar Combining Ratios Using Radioisotopes--A Student Experiment

    ERIC Educational Resources Information Center

    Sears, Jerry A.

    1976-01-01

    Outlines an experimental procedure in which an iodine radioisotope is used to determine molar combining ratios of lead and silver with the iodine. Tables and graphs show the definitive results that should be attainable. (CP)

  10. Tuning aspect ratio of hierarchical ZnO nanotetrapod

    NASA Astrophysics Data System (ADS)

    Yan, Youguo; Li, Chuanyong; Zhou, Lixia; Liu, Bing; Zhang, Jun

    2016-12-01

    Fine-tuning the aspect ratio is crucial for practical application and optimizing various properties of nanostructure. In this work, a mixed metal (Zn) and oxide (ZnO + C) powder was adopted as precursor to obtain initial high reagent vapour pressure and subsequent low reagent vapour pressure, and one kind of hierarchical ZnO nanotetrapod with legs composed of thick primary nanorod and thin secondary nanowire was successfully synthesized. Two growth stages controlled by the reagent supersaturation ratio were proposed to unveil the underlying growth mechanism of this hierarchical structure. Further, a series of comparative experiments were undertaken to validate the growth mode and explore the growth strategy tailoring the aspect ratio. Our results suggest one accessible approach to manipulate the aspect ratio, and the growth mode has some promises for preparing hierarchical nanoblocks with specific geometry demanding.

  11. India’s Distorted Sex Ratio: Dire Consequences for Girls

    PubMed Central

    Roberts, Lisa R.; Montgomery, Susanne B.

    2017-01-01

    Female gender discrimination related to cultural preference for males is a common global problem, especially in Asian countries. Numerous laws intended to prevent discrimination on the basis of gender have been passed in India, yet the distorted female-to-male sex ratio seems to show worsening tendencies. Using detailed, two-year longitudinal chart abstraction data about delivery records of a private mission hospital in rural India, we explored if hospital birth ratio data differed in comparison to regional data, and what demographic and contextual variables may have influenced these outcomes. Using quantitative chart abstraction and qualitative contextual data, study results showed the female-to-male ratio was lower than the reported state ratio at birth. In the context of India’s patriarchal structure, with its strong son preference, women are under tremendous pressure or coerced to access community-based, sex-selective identification and female fetus abortion. Nurses may be key to turning the tide.

  12. Hazard ratios in cancer clinical trials--a primer.

    PubMed

    Blagoev, Krastan B; Wilkerson, Julia; Fojo, Tito

    2012-01-31

    The increase and diversity of clinical trial data has resulted in a greater reliance on statistical analyses to discern value. Assessing differences between two similar survival curves can pose a challenge for those without formal training in statistical interpretation; therefore, there has been an increased reliance on hazard ratios often to the exclusion of more-traditional survival measures. However, because a hazard ratio lacks dimensions it can only inform the reader about the reliability and uniformity of the data. It does not provide practitioners with quantitative values they can use, nor does it provide information they can discuss with patients. Motivated by a non-scientific poll of oncologists in training and those with board certification that suggested only a limited understanding of the derivation of hazard ratios we undertook this presentation of hazard ratios: a measure of treatment efficacy that is increasingly used and often misused.

  13. Negative poisson's ratio in single-layer black phosphorus.

    PubMed

    Jiang, Jin-Wu; Park, Harold S

    2014-08-18

    The Poisson's ratio is a fundamental mechanical property that relates the resulting lateral strain to applied axial strain. Although this value can theoretically be negative, it is positive for nearly all materials, though negative values have been observed in so-called auxetic structures. However, nearly all auxetic materials are bulk materials whose microstructure has been specifically engineered to generate a negative Poisson's ratio. Here we report using first-principles calculations the existence of a negative Poisson's ratio in a single-layer, two-dimensional material, black phosphorus. In contrast to engineered bulk auxetics, this behaviour is intrinsic for single-layer black phosphorus, and originates from its puckered structure, where the pucker can be regarded as a re-entrant structure that is comprised of two coupled orthogonal hinges. As a result of this atomic structure, a negative Poisson's ratio is observed in the out-of-plane direction under uniaxial deformation in the direction parallel to the pucker.

  14. Tuning the Poisson's Ratio of Biomaterials for Investigating Cellular Response

    PubMed Central

    Meggs, Kyle; Qu, Xin; Chen, Shaochen

    2013-01-01

    Cells sense and respond to mechanical forces, regardless of whether the source is from a normal tissue matrix, an adjacent cell or a synthetic substrate. In recent years, cell response to surface rigidity has been extensively studied by modulating the elastic modulus of poly(ethylene glycol) (PEG)-based hydrogels. In the context of biomaterials, Poisson's ratio, another fundamental material property parameter has not been explored, primarily because of challenges involved in tuning the Poisson's ratio in biological scaffolds. Two-photon polymerization is used to fabricate suspended web structures that exhibit positive and negative Poisson's ratio (NPR), based on analytical models. NPR webs demonstrate biaxial expansion/compression behavior, as one or multiple cells apply local forces and move the structures. Unusual cell division on NPR structures is also demonstrated. This methodology can be used to tune the Poisson's ratio of several photocurable biomaterials and could have potential implications in the field of mechanobiology. PMID:24076754

  15. Lidar extinction-to-backscatter ratio of the ocean.

    PubMed

    Churnside, James H; Sullivan, James M; Twardowski, Michael S

    2014-07-28

    Bio-optical models are used to develop a model of the lidar extinction-to-backscatter ratio applicable to oceanographic lidar. The model is based on chlorophyll concentration, and is expected to be valid for Case 1 waters. The limiting cases of narrow- and wide-beam lidars are presented and compared with estimates based on in situ optical measurements. Lidar measurements are also compared with the model using in situ or satellite estimates of chlorophyll concentration. A modified lidar ratio is defined, in which the properties of pure sea water are removed. This modified ratio is shown to be nearly constant for wide-beam lidar operating in low-chlorophyll waters, so accurate inversion to derive extinction and backscattering is possible under these conditions. This ratio can also be used for lidar calibration.

  16. Analysis of isomeric ratios for medium-mass nuclei

    NASA Astrophysics Data System (ADS)

    Danagulyan, A. S.; Hovhannisyan, G. H.; Bakhshiyan, T. M.; Kerobyan, I. A.

    2016-09-01

    Values of the isomeric ratios for product nuclei originating from simple charge-exchange reactions were analyzed. The cross sections for the formation of product nuclei in ground and isomeric states were calculated with the aid of the TALYS 1.4 and EMPIRE 3.2 codes. The calculated values of the isomeric ratios were compared with their experimental counterparts taken from the EXFOR database. For the 86,87Y, 94,95,96,99Tc, and 44Sc nuclei, the experimental values of the isomeric ratios exceed the respective calculated values. The nuclei in question feature weak deformations and have high-spin yrast lines and rotational bands. The possible reason behind the discrepancy between theoretical and experimental isomeric ratios is that the decay of yrast states leads with a high probability to the formation of isomeric states of detected product nuclei.

  17. Lattice QCD results on cumulant ratios at freeze-out

    NASA Astrophysics Data System (ADS)

    Karsch, Frithjof

    2017-01-01

    Ratios of cumulants of net proton-number fluctuations measured by the STAR Collaboration show strong deviations from a skellam distribution, which should describe thermal properties of cumulant ratios, if proton-number fluctuations are generated in equilibrium and a hadron resonance gas (HRG) model would provide a suitable description of thermodynamics at the freeze-out temperature. We present some results on 6 th order cumulants entering the calculation of the QCD equation of state at non-zero values of the baryon chemical potential (μB ) and discuss limitations on the applicability of HRG thermodynamics deduced from a comparison between QCD and HRG model calculations of cumulants of conserved charge fluctuations. We show that basic features of the μB -dependence of skewness and kurtosis ratios of net proton-number fluctuations measured by the STAR Collaboration resemble those expected from a QCD calculation of the corresponding net baryon-number cumulant ratios.

  18. Effect of area ratio on the performance of a 5.5:1 pressure ratio centrifugal impeller

    NASA Technical Reports Server (NTRS)

    Schumann, L. F.; Clark, D. A.; Wood, J. R.

    1986-01-01

    A centrifugal impeller which was initially designed for a pressure ratio of approximately 5.5 and a mass flow rate of 0.959 kg/sec was tested with a vaneless diffuser for a range of design point impeller area ratios from 2.322 to 2.945. The impeller area ratio was changed by successively cutting back the impeller exit axial width from an initial value of 7.57 mm to a final value of 5.97 mm. In all, four separate area ratios were tested. For each area ratio a series of impeller exit axial clearances was also tested. Test results are based on impeller exit surveys of total pressure, total temperature, and flow angle at a radius 1.115 times the impeller exit radius. Results of the tests at design speed, peak efficiency, and an exit tip clearance of 8 percent of exit blade height show that the impeller equivalent pressure recovery coefficient peaked at a design point area ratio of approximately 2.748 while the impeller aerodynamic efficiency peaked at a lower value of area ratio of approximately 2.55. The variation of impeller efficiency with clearance showed expected trends with a loss of approximately 0.4 points in impeller efficiency for each percent increase in exit axial tip clearance for all impellers tested.

  19. Influence of molar ratios on properties of magnesium oxychloride cement

    SciTech Connect

    Li Zongjin . E-mail: zongjin@ust.hk; Chau, C.K.

    2007-06-15

    A parametric study has been conducted to investigate the influences of the molar ratios of MgO/MgCl{sub 2} and H{sub 2}O/MgCl{sub 2} on the properties of magnesium oxychloride (MOC) cement. By an integrated assessment of the experimental studies of strength development and X-ray diffractograms, together with application of the relevant phase diagram, it is recognized that the molar ratios of MgO/MgCl{sub 2} and H{sub 2}O/MgCl{sub 2} can significantly affect the properties of MOC cement. For a MOC cement paste possessing a dominance of 5MgO.MgCl{sub 2}.8H{sub 2}O (phase 5) crystals, the molar ratios of MgO/MgCl{sub 2} of 11-17 and H{sub 2}O/MgCl{sub 2} of 12-18 are found to be the most favorite ranges for design purpose. The choose of the molar ratio of H{sub 2}O/MgCl{sub 2} is, however, largely depends on the molar ratio of MgO/MgCl{sub 2} mainly for controlling workability of paste. Therefore, the most critical parameter to be selected in the design process is the molar ratio of MgO/MgCl{sub 2}, although the reactivity of the MgO powder is also important. Besides, the molar ratio can also be affected by the reactivity of the MgO powder to be employed. It is believed that a molar ratio of MgO/MgCl{sub 2} of 13, the most suitable one shown in this study, can be used as a starting point in the normal practice.

  20. Velocity ratio and its application to predicting velocities

    USGS Publications Warehouse

    Lee, Myung W.

    2003-01-01

    The velocity ratio of water-saturated sediment derived from the Biot-Gassmann theory depends mainly on the Biot coefficient?a property of dry rock?for consolidated sediments with porosity less than the critical porosity. With this theory, the shear moduli of dry sediments are the same as the shear moduli of water-saturated sediments. Because the velocity ratio depends on the Biot coefficient explicitly, Biot-Gassmann theory accurately predicts velocity ratios with respect to differential pressure for a given porosity. However, because the velocity ratio is weakly related to porosity, it is not appropriate to investigate the velocity ratio with respect to porosity (f). A new formulation based on the assumption that the velocity ratio is a function of (1?f)n yields a velocity ratio that depends on porosity, but not on the Biot coefficient explicitly. Unlike the Biot-Gassmann theory, the shear moduli of water-saturated sediments depend not only on the Biot coefficient but also on the pore fluid. This nonclassical behavior of the shear modulus of water-saturated sediment is speculated to be an effect of interaction between fluid and the solid matrix, resulting in softening or hardening of the rock frame and an effect of velocity dispersion owing to local fluid flow. The exponent n controls the degree of softening/hardening of the formation. Based on laboratory data measured near 1 MHz, this theory is extended to include the effect of differential pressure on the velocity ratio by making n a function of differential pressure and consolidation. However, the velocity dispersion and anisotropy are not included in the formulation.

  1. Algorithm for astronomical, point source, signal to noise ratio calculations

    NASA Technical Reports Server (NTRS)

    Jayroe, R. R.; Schroeder, D. J.

    1984-01-01

    An algorithm was developed to simulate the expected signal to noise ratios as a function of observation time in the charge coupled device detector plane of an optical telescope located outside the Earth's atmosphere for a signal star, and an optional secondary star, embedded in a uniform cosmic background. By choosing the appropriate input values, the expected point source signal to noise ratio can be computed for the Hubble Space Telescope using the Wide Field/Planetary Camera science instrument.

  2. Atmospheric helium isotope ratio: Possible temporal and spatial variations

    NASA Astrophysics Data System (ADS)

    Sano, Yuji; Furukawa, Yukiko; Takahata, Naoto

    2010-09-01

    The atmospheric 3He/ 4He ratio has been considered to be constant on a global scale, because the residence time of helium is significantly longer than the mixing time in the atmosphere. However, this ratio may be decreasing with time owing to the anthropogenic release of crustal helium from oil and natural gas wells, although this observation has been disputed. Here, we present the 3He/ 4He ratios of old air trapped in historical slags in Japan and of modern surface air samples collected at various sites around the world, measured with a newly developed analytical system. In air helium extracted from metallurgical slag found at refineries in operation between AD 1603 and 1907 in Japan, we determined a mean 3He/ 4He ratio of (5106 ± 108) × 10 -5 R HESJ (where R HESJ is the 3He/ 4He ratio of the Helium Standard of Japan), which is consistent with the previously reported value of (5077 ± 59) × 10 -5 R HESJ for historical slags in France and United Arab Emirates and about 4% higher than that of average modern air, (4901 ± 4) × 10 -5 R HESJ. This result implies that the air 3He/ 4He ratio has decreased with time as expected by anthropogenic causes. Our modern surface air samples revealed that the 3He/ 4He ratio increases from north to south at a rate of (0.16 ± 0.08) × 10 -5 R HESJ/degree of latitude, suggesting that the low 3He/ 4He ratio originates in high-latitude regions of the northern hemisphere, which is consistent with the fact that most fossil fuel is extracted and consumed in the northern hemisphere.

  3. Retrieval of constituent mixing ratios from limb thermal emission spectra

    NASA Technical Reports Server (NTRS)

    Shaffer, William A.; Kunde, Virgil G.; Conrath, Barney J.

    1988-01-01

    An onion-peeling iterative, least-squares relaxation method to retrieve mixing ratio profiles from limb thermal emission spectra is presented. The method has been tested on synthetic data, containing various amounts of added random noise for O3, HNO3, and N2O. The retrieval method is used to obtain O3 and HNO3 mixing ratio profiles from high-resolution thermal emission spectra. Results of the retrievals compare favorably with those obtained previously.

  4. System and method for high precision isotope ratio destructive analysis

    DOEpatents

    Bushaw, Bruce A; Anheier, Norman C; Phillips, Jon R

    2013-07-02

    A system and process are disclosed that provide high accuracy and high precision destructive analysis measurements for isotope ratio determination of relative isotope abundance distributions in liquids, solids, and particulate samples. The invention utilizes a collinear probe beam to interrogate a laser ablated plume. This invention provides enhanced single-shot detection sensitivity approaching the femtogram range, and isotope ratios that can be determined at approximately 1% or better precision and accuracy (relative standard deviation).

  5. Determining the Optimal C-130 Deployed Crew Ratio

    DTIC Science & Technology

    2014-06-13

    planning factors, intratheater airlift demand and less quantifiable aspects of crew ratio planning such as circadian rhythm disruption. The initial review...factors such as circadian rhythm and sleep cycle disruption cannot be ignored. The target audience for Fundamentals of Shiftwork Scheduling is not...mission length plus 3 hours pre-flight and 2 hours post-flight). This could result in significant circadian rhythm disruptions unless a crew ratio

  6. Statistical analyses of plume composition and deposited radionuclide mixture ratios

    SciTech Connect

    Kraus, Terrence D.; Sallaberry, Cedric Jean-Marie; Eckert-Gallup, Aubrey Celia; Brito, Roxanne; Hunt, Brian D.; Osborn, Douglas M.

    2014-01-01

    A proposed method is considered to classify the regions in the close neighborhood of selected measurements according to the ratio of two radionuclides measured from either a radioactive plume or a deposited radionuclide mixture. The subsequent associated locations are then considered in the area of interest with a representative ratio class. This method allows for a more comprehensive and meaningful understanding of the data sampled following a radiological incident.

  7. Rotor Performance at High Advance Ratio: Theory versus Test

    NASA Technical Reports Server (NTRS)

    Harris, Franklin D.

    2008-01-01

    Five analytical tools have been used to study rotor performance at high advance ratio. One is representative of autogyro rotor theory in 1934 and four are representative of helicopter rotor theory in 2008. The five theories are measured against three sets of well documented, full-scale, isolated rotor performance experiments. The major finding of this study is that the decades spent by many rotorcraft theoreticians to improve prediction of basic rotor aerodynamic performance has paid off. This payoff, illustrated by comparing the CAMRAD II comprehensive code and Wheatley & Bailey theory to H-34 test data, shows that rational rotor lift to drag ratios are now predictable. The 1934 theory predicted L/D ratios as high as 15. CAMRAD II predictions compared well with H-34 test data having L/D ratios more on the order of 7 to 9. However, the detailed examination of the selected codes compared to H-34 test data indicates that not one of the codes can predict to engineering accuracy above an advance ratio of 0.62 the control positions and shaft angle of attack required for a given lift. There is no full-scale rotor performance data available for advance ratios above 1.0 and extrapolation of currently available data to advance ratios on the order of 2.0 is unreasonable despite the needs of future rotorcraft. Therefore, it is recommended that an overly strong full-scale rotor blade set be obtained and tested in a suitable wind tunnel to at least an advance ratio of 2.5. A tail rotor from a Sikorsky CH-53 or other large single rotor helicopter should be adequate for this exploratory experiment.

  8. Implications of a high population 2 B/Be ratio

    NASA Technical Reports Server (NTRS)

    Fields, Brian D.; Olive, Keith A.; Schramm, David N.

    1995-01-01

    The observed boron/beryllium ratio in extreme Population II stars has been interpreted as evidence of Be and B synthesis by early Galactic cosmic rays. However, a recent reanalysis of the boron abundance in the Population II halo star HD 140823 suggests that B/H may be larger than previously reported, by as much as a factor of 4. This would yield a B/Be ratio lying in the range 14 less than or approximately equal to B/Be less than or approximately equal to 50. The possibilty of a high Population II B/Be ratio stresses the importance of the upper limit to the B/Be ratio arising from cosmic-ray production. It is found that the limit to cosmic-ray-produced B/Be depends upon the assumed cosmic-ray spectrum. For any Population II cosmic-ray spectrum that is a single power law in either total energy per nucleon or in momentum, the B/Be ratio constrained to lie in the range 7.6 less than or approximately equal to B/Be less than or approximately equal to 14. Thus, if the new B/Be ratio is correct, it requires either a bimodal cosmic-ray flux with a large low-energy component, or, for another B source, possibly the proposed nu-process in supernovae, either of which may be helpful in explaining the observed B-11/B-10 ratio. Finally, it is noted that the boron reanalysis highlights the uncertainty in our knowledge of the B/Be ratio, and the need for additional data on Be and B abundances.

  9. Temperature Dependence of Isotope Ratios in Tree Rings

    PubMed Central

    Libby, L. M.; Pandolfi, L. J.

    1974-01-01

    The stable isotope ratios of carbon, oxygen, and hydrogen have been measured for a German oak in wood samples of roughly three years each, for the years 1712-1954 A.D., and correlated with the existing weather records from England, Basel, and Geneva to evaluate the empirical temperature coefficients. Isotope ratios in a second official oak, measured for the years 1530-1800 A.D., show the cold temperatures of the Little Ice Age interspersed with warm intervals. PMID:16592163

  10. Increased skeletal:renal uptake ratio. [Bone-seekers

    SciTech Connect

    Cheng, T.H.; Holman, B.L.

    1980-08-01

    Twenty-four patients with increased skeletal:renal uptake ratios of /sup 99m/Tc-methylene diphosphonate were studied. Increased uptake was central in metastatic prostate carcinoma, peripheral in hematologic disorders, and heterogeneous in Paget disease and fibrous dysplasia. There was no discernible redistribution of skeletal uptake in patients with renal failure. Absence of both renal and bladder activity was not observed in patients with normal renal function. An increased ratio was always abnormal and frequently indicated diffuse bone disease.

  11. Why ratio dependence is (still) a bad model of predation.

    PubMed

    Abrams, Peter A

    2015-08-01

    The history of the idea that predation rates are functions of the ratio of prey density to predator density, known as ratio dependence, is reviewed and updated. When the term was introduced in 1989, it was already known that higher predator abundance often reduced an individual predator's average intake rate of prey. However, the idea that this effect was a universally applicable inverse proportionality was new. That idea was widely criticized in many articles in the early 1990s, and many of these criticisms have never been addressed. Nevertheless, ratio dependence seems to be gaining in popularity and is the subject of a recent monograph by the originators. This article revisits the most important objections to this theory, and assesses to what extent they have been answered by the theory's proponents. In this process, several new objections are raised. The counterarguments begin with the lack of a plausible, generally applicable mechanism that could produce ratio dependence. They include the fact that ratio dependence is a special case of predator-density effects, which, in turn, are only one of many non-prey species effects that influence the consumption rate of a particular prey. The proclaimed simplicity advantage of ratio dependence is at best small and is outweighed by its disadvantages; it predicts biologically implausible phenomena, and cannot easily be extended to describe multi-species systems, trait-mediated interactions, coevolution, and a number of other important ecological phenomena. Any potential small simplicity advantage disappears with corrections to remove unrealistic low-density dynamics caused by ratio dependence. The frequent occurrence of strong predator dependence does not make ratio dependence a better 'default' model of predation than prey dependence, and empirical studies of the full range of non-prey species effects on the consumption rates of predators are needed.

  12. Spin polarization ratios of resistivity and density of states estimated from anisotropic magnetoresistance ratio for nearly half-metallic ferromagnets

    NASA Astrophysics Data System (ADS)

    Kokado, Satoshi; Sakuraba, Yuya; Tsunoda, Masakiyo

    2016-10-01

    We derive a simple relational expression between the spin polarization ratio of resistivity, Pρ, and the anisotropic magnetoresistance ratio Δρ/ρ, and that between the spin polarization ratio of the density of states at the Fermi energy, PDOS, and Δρ/ρ for nearly half-metallic ferromagnets. We find that Pρ and PDOS increase with increasing |Δρ/ρ| from 0 to a maximum value. In addition, we roughly estimate Pρ and PDOS for a Co2FeGa0.5Ge0.5 Heusler alloy by substituting its experimentally observed Δρ/ρ into the respective expressions.

  13. Effects of Planetary Gear Ratio on Mean Service Life

    NASA Technical Reports Server (NTRS)

    Savage, M.; Rubadeux, K. L.; Coe, H. H.

    1996-01-01

    Planetary gear transmissions are compact, high-power speed reductions which use parallel load paths. The range of possible reduction ratios is bounded from below and above by limits on the relative size of the planet gears. For a single plane transmission, the planet gear has no size at a ratio of two. As the ratio increases, so does the size of the planets relative to the sizes of the sun and ring. Which ratio is best for a planetary reduction can be resolved by studying a series of optimal designs. In this series, each design is obtained by maximizing the service life for a planetary with a fixed size, gear ratio, input speed power and materials. The planetary gear reduction service life is modeled as a function of the two-parameter Weibull distributed service lives of the bearings and gears in the reduction. Planet bearing life strongly influences the optimal reduction lives which point to an optimal planetary reduction ratio in the neighborhood of four to five.

  14. Effects of Planetary Speed Reduction Ratio on Mean Service Life

    NASA Technical Reports Server (NTRS)

    Savage, M.; Rubadeux, K. L.; Coe, H. H.

    1998-01-01

    Planetary gear transmissions are compact speed reductions which use parallel-load paths to transmit high power. The range of possible reduction ratios is bounded from below and above by limits on the relative size of the planet gears. For a single plane planetary transmission, the speed-reduction ratio must be greater than two for planet gears to exist. As the ratio increase, so does the size of the planets relative to the sizes of the sun and ring. Which ratio is best for a planetary reduction can be resolved by studying a series of optimal designs. In this series, each design is obtained by maximizing the service life for a spur-gear planetary with a fixed size, speed reduction ratio, input speed, power and materials. The planetary gear reduction service life is modeled as a function of the two-parameter Weibull distributed service lives of the ball bearings and spur gears in the reduction. Planet-bearing life strongly influences the optimal reduction lives which point to an optimal planetary reduction ratio in the neighborhood of four to five.

  15. Elliptic nozzle aspect ratio effect on controlled jet propagation

    NASA Astrophysics Data System (ADS)

    Aravindh Kumar, S. M.; Rathakrishnan, Ethirajan

    2017-04-01

    The present study deals with the control of a Mach 2 elliptic jet from a convergent–divergent elliptic nozzle of aspect ratio 4 using tabs at the nozzle exit. The experiments were carried out for rectangular and triangular tabs of the same blockage, placed along the major and minor axes of the nozzle exit, at different levels of nozzle expansion. The triangular tabs along the minor axis promoted superior mixing compared to the other controlled jets and caused substantial core length reduction at all the nozzle pressure ratios studied. The rectangular tabs along the minor axis caused core length reduction at all pressure ratios, but the values were minimal compared to that of triangular tabs along the minor axis. For all the test conditions, the mixing promotion caused by tabs along the major axis was inferior to that of tabs along the minor axis. The waves present in the core of controlled jets were visualized using a shadowgraph. Comparison of the present results with the results of a controlled Mach 2 elliptic jet of aspect ratio 2 (Aravindh Kumar and Sathakrishnan 2016 J. Propulsion Power 32 121–33, Aravindh Kumar and Rathakrishnan 2016 J. Aerospace Eng. at press (doi:10.1177/0954410016652921)) show that for all levels of expansion, the mixing effectiveness of triangular tabs along the minor axis of an aspect ratio 4 nozzle is better than rectangular or triangular tabs along the minor axis of an aspect ratio 2 nozzle.

  16. Child underreporting, fertility, and sex ratio imbalance in China.

    PubMed

    Goodkind, Daniel

    2011-02-01

    Child underreporting is often neglected in studies of fertility and sex ratio imbalance in China. To improve estimates of these measures, I use intercensal comparisons to identify a rise in underreporting, which followed the increased enforcement and penalization under the birth planning system in 1991. A new triangulation of evidence indicates that about 19% of children at ages 0-4 were unreported in the 2000 census, more than double that of the 1990 census. This evidence contradicts assumptions underlying the fertility estimates of most recent studies. Yet, the analysis also suggests that China's fertility in the late 1990s (and perhaps beyond) was below officially adjusted levels. I then conduct a similar intercensal analysis of sex ratios of births and children, which are the world's highest primarily because of prenatal sex selection. However, given excess underreporting of young daughters, especially pronounced just after 1990, estimated ratios are lower than reported ratios. Sex ratios in areas with a "1.5-child" policy are especially distorted because of excess daughter underreporting, as well as sex-linked stopping rules and other factors, although it is unclear whether such policies increase use of prenatal sex selection. China's sex ratio at birth, once it is standardized by birth order, fell between 2000 and 2005 and showed a continuing excess in urban China, not rural China.

  17. Physics of Coanda jet detachment at high-pressure ratio

    NASA Astrophysics Data System (ADS)

    Cornelius, Kenneth C.; Lucius, Gerald A.

    1994-05-01

    Experimental measurements of surface pressure for an underexpanded two-dimensional supersonic Coanda flow with static conditions exterior to the jet flow was obtained for a fixed slot height to a radius ratio of 0.04. The data demonstrate that an oblique shock forms near the jet exit plane which vectors the jet flow from the curved surface at a pressure ratio of 7.6. The jet detachment occurs at a pressure ratio which is a function of the ratio of slot height to cylinder radius. An increase in the pressure ratio to 11.5 before jet detachment has been demonstrated by the translation of the upper wall providing for a converging-diverging geometry. The physics of the Coanda expansion and the jet detachment are qualitatively described using an optical schlieren system. A compressible inviscid model was derived analytically to demonstrate the variation in Mach number and surface pressure as a function of the geometric parameters with increasing pressure ratio.

  18. Theoretical and experimental plastic strain ratios in planar isotropic textures

    NASA Astrophysics Data System (ADS)

    Kim, Insoo

    1996-06-01

    The plastic strain ratios of planar isotropic sheet specimens were studied by using unidirectionally solidified commercial Al. Sn and Al-Cu alloy sheets and Cu sheets electrodeposited under the various electrolysis conditions. The measured plastic strain ratios of [100] planar isotropic sheets by using unidirectionally solidified Al and Al-Cu alloy are about 0.17-0.52, that of [110] planar isotropic sheets using unidirectionally solidified Sn(BCT) are about 2.5, that of [110] planar isotropic sheets using electrodeposited Cu are 1.38-2.05 and that of [111] planar isotropic sheets using electrodeposited Cu are 2.61-2.85. There is a substantial discrepancy between the experimental plastic strain ratios which are measured from planar isotropic sheets and theoretical plastic strain ratios which are calculated by Backofen method and Bunge method, but the measured plastic strain ratio of [100] planar isotropic sheet using unidirectionally solidified Al and Al-Cu alloy is in good agreement with Bunge method and the measured plastic strain ratio of [110] and [111] planar isotropic sheets using electrodeposited Cu are in good agreement with Backofen method.

  19. Measurement of Poisson's ratio of dental composite restorative materials.

    PubMed

    Chung, Sew Meng; Yap, Adrian U Jin; Koh, Wee Kiat; Tsai, Kuo Tsing; Lim, Chwee Teck

    2004-06-01

    The aim of this study was to determine the Poisson ratio of resin-based dental composites using a static tensile test method. Materials used in this investigation were from the same manufacturer (3M ESPE) and included microfill (A110), minifill (Z100 and Filtek Z250), polyacid-modified (F2000), and flowable (Filtek Flowable [FF]) composites. The Poisson ratio of the materials were determined after 1 week conditioning in water at 37 degrees C. The tensile test was performed with using a uniaxial testing system at crosshead speed of 0.5 mm/min. Data was analysed using one-way ANOVA/post-hoc Scheffe's test and Pearson's correlation test at significance level of 0.05. Mean Poisson's ratio (n=8) ranged from 0.302 to 0.393. The Poisson ratio of FF was significantly higher than all other composites evaluated, and the Poisson ratio of A110 was higher than Z100, Z250 and F2000. The Poisson ratio is higher for materials with lower filler volume fraction.

  20. Caste ratios affect the reproductive output of social trematode colonies.

    PubMed

    Kamiya, T; Poulin, R

    2013-03-01

    Intraspecific phenotypic diversification in social organisms often leads to formation of physical castes which are morphologically specialized for particular tasks within the colony. The optimal caste allocation theory argues that specialized morphological castes are efficient at specific tasks, and hence different caste ratios should affect the ergonomic efficiency, hence reproductive output of the colony. However, the reproductive output of different caste ratios has been documented in few species of insects with equivocal support for the theory. This study investigated whether the ratios of nonreproductive and reproductive morphs affect the reproductive output of a recently discovered social trematode, Philophthalmus sp., in which the nonreproductive members are hypothesized to be defensive specialists. A census of natural infections and a manipulative in vitro experiment demonstrated a positive association between the reproductive output of trematode colonies and the ratio of nonreproductive to reproductive morphs in the presence of an intra-host trematode competitor, Maritrema novaezealandensis. On the contrary, without the competitor, reproductive output was negatively associated with the proportion of nonreproductive castes in colonies. Our findings demonstrate for the first time a clear fitness benefit associated with the nonreproductive castes in the presence of a competitor while illustrating the cost of maintaining such morphs in noncompetitive situations. Although the proximate mechanisms controlling caste ratio remain unclear in this trematode system, this study supports the prediction that the fitness of colonies is influenced by the composition of specialized functional morphs in social organisms, suggesting a potential for adaptive shifts of caste ratios over evolutionary time.

  1. Temporal trends in the secondary sex ratio in Nordic countries.

    PubMed

    Fellman, Johan; Eriksson, Aldur W

    2011-01-01

    Attempts have been made to identify factors influencing the number of males per 100 females at birth, also called the secondary sex ratio. It has been proposed to vary inversely with the frequency of prenatal losses, but available data lend at best only weak support for this hypothesis. Statistical analyses have shown that comparisons between secondary sex ratios demand large data sets. Variations in the secondary sex ratio that have been reliably identified in family data have mostly been slight and without a notable influence on national birth registers. For Sweden, 1751-1950, the secondary sex ratio among all births and live births revealed increasing trends. The Swedish results are compared with available findings for live births in Finland, Norway, Denmark, and the small Icelandic population. For Norway and Denmark, the secondary sex ratio increased during 1801-1950. A similar, but stronger pattern was observed for Finland (1751-1950) and Iceland (1838-1950). During the latter half of the twentieth century, marked decreases were observed in all countries. Attempts to identify reliable associations between secondary sex ratios and stillbirth rates have been made, but no consistent results have emerged.

  2. Reinforcement magnitude and pausing on progressive-ratio schedules

    PubMed Central

    Baron, Alan; Mikorski, Jeffrey; Schlund, Michael

    1992-01-01

    Rats responded under progressive-ratio schedules for sweetened milk reinforcers; each session ended when responding ceased for 10 min. Experiment 1 varied the concentration of milk and the duration of postreinforcement timeouts. Postreinforcement pausing increased as a positively accelerated function of the size of the ratio, and the rate of increase was reduced as a function of concentration and by timeouts of 10 s or longer. Experiment 2 varied reinforcement magnitude within sessions (number of dipper operations per reinforcer) in conjunction with stimuli correlated with the upcoming magnitude. In the absence of discriminative stimuli, pausing was longer following a large reinforcer than following a small one. Pauses were reduced by a stimulus signaling a large upcoming reinforcer, particularly at the highest ratios, and the animals tended to quit responding when the past reinforcer was large and the stimulus signaled that the next one would be small. Results of both experiments revealed parallels between responding under progressive-ratio schedules and other schedules containing ratio contingencies. Relationships between pausing and magnitude suggest that ratio pausing is under the joint control of inhibitory properties of the past reinforcer and excitatory properties of stimuli correlated with the upcoming reinforcer, rather than under the exclusive control of either factor alone. PMID:16812671

  3. Increasing the transformer ratio at the Argonne wakefield accelerator.

    SciTech Connect

    Power, J.G.; Conde, M.; Liu, W.; Yusof, Z.; Gai, W.; Jing, C.; Kanareykin, A.

    2011-01-01

    The transformer ratio is defined as the ratio of the maximum energy gain of the witness bunch to the maximum energy loss experienced by the drive bunch (or a bunch within a multidrive bunch train). This plays an important role in the collinear wakefield acceleration scheme. A high transformer ratio is desirable since it leads to a higher overall efficiency under similar conditions (e.g. the same beam loading, the same structure, etc.). One technique to enhance the transformer ratio beyond the ordinary limit of 2 is to use a ramped bunch train. The first experimental demonstration observed a transformer ratio only marginally above 2 due to the mismatch between the drive microbunch length and the frequency of the accelerating structure [C. Jing, A. Kanareykin, J. Power, M. Conde, Z. Yusof, P. Schoessow, and W. Gai, Phys. Rev. Lett. 98, 144801 (2007)]. Recently, we revisited this experiment with an optimized microbunch length using a UV laser stacking technique at the Argonne Wakefield Accelerator facility and measured a transformer ratio of 3.4. Measurements and data analysis from these experiments are presented in detail.

  4. Cesium isotope ratios as indicators of nuclear power plant operations.

    PubMed

    Delmore, James E; Snyder, Darin C; Tranter, Troy; Mann, Nick R

    2011-11-01

    There are multiple paths by which radioactive cesium can reach the effluent from reactor operations. The radioactive (135)Cs/(137)Cs ratios are controlled by these paths. In an effort to better understand the origin of this radiation, these (135)Cs/(137)Cs ratios in effluents from three power reactor sites have been measured in offsite samples. These ratios are different from global fallout by up to six fold and as such cannot have a significant component from this source. A cesium ratio for a sample collected outside of the plant boundary provides integration over the operating life of the reactor. A sample collected inside the plant at any given time can be much different from this lifetime ratio. The measured cesium ratios vary significantly for the three reactors and indicate that the multiple paths have widely varying levels of contributions. There are too many ways these isotopes can fractionate to be useful for quantitative evaluations of operating parameters in an offsite sample, although it may be possible to obtain limited qualitative information for an onsite sample.

  5. High/variable mixture ratio oxygen/hydrogen engines

    NASA Technical Reports Server (NTRS)

    Knuth, William H.; Beveridge, John H.

    1988-01-01

    A LOX/LH2 high/variable mixture ratio booster upper stage is described. The engine has high thrust-weight ratio as a booster and high specific impulse as an upper stage engine. Operation at high mixture ratio utilizes the propellants at high bulk density. The engine may use multiple turbopump-preburners for higher thrust ratings. The engine uses the full flow cycle to obtain minimum turbine inlet temperatures for a given chamber pressure and to avoid interpropellant shaft seals and other single point failure modes. A portion of the liquid hydrogen is used to regeneratively cool the thrust chamber assembly. The warmed hydrogen coolant is then used to drive the fuel boost turbopump. All propellants arrive at the gas-gas injector ready to burn. Shear mixing of the parallel flowing high velocity, low density fuel-rich gases with the high density, low velocity oxidizer-rich gases provides complete combustion with a modest chamber volume. Combustion stability is assured by the injection of the heated fuel-rich gases and the comparatively low volume ratio of the propellants before and after combustion. The high area ratio nozzle skirt is fitted with a low area ratio nozzle skirt insert for optimum low altitude performance. The overall engine characteristics make it a candidate for ALS, Shuttle-C, LRB, and SSTO applications.

  6. Cesium Isotope Ratios as Indicators of Nuclear Power Plant Operations

    SciTech Connect

    Darin Snyder; James Delmore; Troy Tranter; Nick Mann; Michael Abbott; John Olson

    2011-11-01

    There are multiple paths by which radioactive cesium can reach the effluent from reactor operations. The radioactive 135Cs/137Cs ratios are controlled by these paths. In an effort to better understand the origin of this radiation, these 135Cs/137Cs ratios in effluents from three power reactor sites have been measured in offsite samples. These ratios are different from global fallout by up to six fold and as such cannot have a significant component from this source. A cesium ratio for a sample collected outside of the plant boundary provides integration over the operating life of the reactor. A sample collected inside the plant at any given time can be much different from this lifetime ratio. The measured cesium ratios vary significantly for the three reactors and indicate that the multiple paths have widely varying levels of contributions. There are too many ways these isotopes can fractionate to be useful for quantitative evaluations of operating parameters in an offsite sample, although it may be possible to obtain limited qualitative information for an onsite sample.

  7. Swirl ratio effects on tornado-like vortices

    NASA Astrophysics Data System (ADS)

    Hashemi-Tari, Pooyan; Gurka, Roi; Hangen, Horia

    2007-11-01

    The effect of swirl ratio on the flow field for a tornado-like vortex simulator (TVS) is investigated. Different swirl ratios are obtained by changing the geometry and tangential velocity which determine the vortex evolution. Flow visualizations, surface pressure and Particle Image Velocimetry (PIV) measurements are performed in a small TVS for swirl ratios S between 0 and 1. The PIV data was acquired for two orthogonal planes: normal and parallel to the solid boundary at several height locations. The ratio between the angular momentum and the radial momentum which characterize the swirl ratio is investigated. Statistical analysis to the turbulent field is performed by mean and rms profiles of the velocity, stresses and vorticity are presented. A Proper Orthogonal Decomposition (POD) is performed on the vorticity field. The results are used to: (i) provide a relation between these 3 sets of qualitative and quantitative measurements and the swirl ratio in an attempt to relate the fluid dynamics parameters to the forensic, Fujita scale, and (ii) understand the spatio-temporal distribution of the most energetic POD modes in a tornado-like vortex.

  8. Determination of Urban VOC Emissions Ratios and Comparison with Inventories

    NASA Astrophysics Data System (ADS)

    Warneke, C.; de Gouw, J.; Goldan, P.; Kuster, W.; Holloway, J.; Williams, E.; Lerner, B.; McKeen, S.; Parrish, D.; Trainer, M.; Fehsenfeld, F.; Kato, S.; Atlas, E.; Baker, A.; Blake, D.

    2006-12-01

    During the NEAQS-ITCT2k4 campaign in New England anthropogenic VOCs and CO were measured downwind from New York City and Boston. The emission ratios of VOCs relative to CO and acetylene were calculated using a method in which the ratio of a VOC with acetylene is plotted versus the photochemical age. The intercept at the photochemical age of zero gives the emission ratio. The so determined emission ratios were compared to other measurement sets, including data from the same location in 2002, canister samples collected inside New York City and Boston, aircraft measurements from Los Angeles in 2002 and the average urban composition of 39 U.S. cities. All the measurements show fairly good agreement. The measured emission ratios also agree well with vehicle exhaust data indicating that a major source of VOCs in urban areas are automobiles. A comparison with an anthropogenic emission inventory shows a rather poor agreement, especially for the C2-C4 alkanes and most oxygenated species. The inventory overestimated toluene for example by almost a factor of three, which caused an air quality forecast model (WRF-CHEM) using this inventory to over-predict the toluene mixing ratio by about a factor of three as well.

  9. Ratio of Sodium to Potassium in the Mercurian Exosphere

    NASA Technical Reports Server (NTRS)

    Potter, A. E.; Anderson, C. M.; Killen, R. M.; Morgan, T. H.

    2001-01-01

    Sodium (Na) and Potassium (K) atoms can be seen in the exosphere of Mercury and the Moon because they are extremely efficient at scattering sunlight. These species must be derived from surface materials, so that we might expect the ratio of sodium to potassium to reflect the ratio of these elements in the surface crust. This expectation is approximately born out for the Moon, where the ratio of sodium to potassium in the lunar exosphere averages to be about 6, not too far from the ratio in lunar rocks of 2 to 7. However, the ratio in the Mercury exosphere was found to be in the range 80 to 190, and at least once, as high as 400. The sodium and potassium atoms seen in the Mercury exosphere represent a balance between production from the surface and loss to space. Only if the production efficiencies and loss rates for Na and K were equal, would the ratio of Na to K in the exosphere reflect the ratio in the surface rocks. Since a value of 100 or more for the ratio of sodium to potassium in the surface rocks seems very unlikely, the high values of the observed ratios suggests that either production efficiencies or loss processes for the two elements are not equivalent. It does not seem likely that source processes should be different on the Moon and Mercury by an order of magnitude. This suggests that loss processes rather than source processes are the cause of the difference between the two. The major loss processes for sodium and potassium on Mercury are radiation pressure and trapping of photoions by the solar wind. Radiation pressure can reach 50-70% of surface gravity, and can sweep sodium and potassium atoms off the planet, provided they are sufficiently hot. Photoionization followed by trapping of the ions in the solar wind is the other major loss process. Photoions are accelerated to keV energies in the magnetosphere, and may either intercept the magnetopause, and be lost from the planet, or impact the planetary surface. Ions that impact the surface are

  10. Breeding Sex Ratios in Adult Leatherback Turtles (Dermochelys coriacea) May Compensate for Female-Biased Hatchling Sex Ratios

    PubMed Central

    Stewart, Kelly R.; Dutton, Peter H.

    2014-01-01

    For vertebrates with temperature-dependent sex determination, primary (or hatchling) sex ratios are often skewed, an issue of particular relevance to concerns over effects of climate change on populations. However, the ratio of breeding males to females, or the operational sex ratio (OSR), is important to understand because it has consequences for population demographics and determines the capacity of a species to persist. The OSR also affects mating behaviors and mate choice, depending on the more abundant sex. For sea turtles, hatchling and juvenile sex ratios are generally female-biased, and with warming nesting beach temperatures, there is concern that populations may become feminized. Our purpose was to evaluate the breeding sex ratio for leatherback turtles at a nesting beach in St. Croix, USVI. In 2010, we sampled nesting females and later sampled their hatchlings as they emerged from nests. Total genomic DNA was extracted and all individuals were genotyped using 6 polymorphic microsatellite markers. We genotyped 662 hatchlings from 58 females, matching 55 females conclusively to their nests. Of the 55, 42 females mated with one male each, 9 mated with 2 males each and 4 mated with at least 3 males each, for a multiple paternity rate of 23.6%. Using GERUD1.0, we reconstructed parental genotypes, identifying 47 different males and 46 females for an estimated breeding sex ratio of 1.02 males for every female. Thus we demonstrate that there are as many actively breeding males as females in this population. Concerns about female-biased adult sex ratios may be premature, and mate choice or competition may play more of a role in sea turtle reproduction than previously thought. We recommend monitoring breeding sex ratios in the future to allow the integration of this demographic parameter in population models. PMID:24505403

  11. Breeding sex ratios in adult leatherback turtles (Dermochelys coriacea) may compensate for female-biased hatchling sex ratios.

    PubMed

    Stewart, Kelly R; Dutton, Peter H

    2014-01-01

    For vertebrates with temperature-dependent sex determination, primary (or hatchling) sex ratios are often skewed, an issue of particular relevance to concerns over effects of climate change on populations. However, the ratio of breeding males to females, or the operational sex ratio (OSR), is important to understand because it has consequences for population demographics and determines the capacity of a species to persist. The OSR also affects mating behaviors and mate choice, depending on the more abundant sex. For sea turtles, hatchling and juvenile sex ratios are generally female-biased, and with warming nesting beach temperatures, there is concern that populations may become feminized. Our purpose was to evaluate the breeding sex ratio for leatherback turtles at a nesting beach in St. Croix, USVI. In 2010, we sampled nesting females and later sampled their hatchlings as they emerged from nests. Total genomic DNA was extracted and all individuals were genotyped using 6 polymorphic microsatellite markers. We genotyped 662 hatchlings from 58 females, matching 55 females conclusively to their nests. Of the 55, 42 females mated with one male each, 9 mated with 2 males each and 4 mated with at least 3 males each, for a multiple paternity rate of 23.6%. Using GERUD1.0, we reconstructed parental genotypes, identifying 47 different males and 46 females for an estimated breeding sex ratio of 1.02 males for every female. Thus we demonstrate that there are as many actively breeding males as females in this population. Concerns about female-biased adult sex ratios may be premature, and mate choice or competition may play more of a role in sea turtle reproduction than previously thought. We recommend monitoring breeding sex ratios in the future to allow the integration of this demographic parameter in population models.

  12. Calibration of the 6302/6301 Stokes V line ratio in terms of the 5250/5247 ratio

    NASA Astrophysics Data System (ADS)

    Stenflo, J. O.; Demidov, M. L.; Bianda, M.; Ramelli, R.

    2013-08-01

    Four decades ago the Stokes V line ratio in the Fe i 5247.06 and 5250.22 Å lines was introduced as a powerful means of exploring the intrinsic field strengths at sub-pixel scales, which led to the discovery that most of the photospheric flux is in intermittent kG form. The "green" 5247-5250 line pair is unique because it allows the magnetic-field effects to be isolated from the thermodynamic effects. No other line pair with this property has since been identified. In recent years much of the magnetic-field diagnostics has been based on the "red" Fe i 6301.5 and 6302.5 Å line pair, since it was chosen in the design of the Hinode space observatory. Although thermodynamic effects severely contaminate the magnetic-field signatures for this line ratio, it is still possible to use it to extract information on intrinsic magnetic fields, but only after it has been "renormalized", since otherwise it produces fictitious, superstrong fields everywhere. In the present work we explore the joint behavior of these two line ratios to determine how the "contaminated" red line ratio can be translated into the corresponding green line ratio, which then allows for a direct interpretation in terms of intrinsic magnetic fields. Our observations are mainly based on recordings with the ZIMPOL-3 spectro-polarimeter at IRSOL in Locarno, Switzerland, complemented by data from the STOP telescope at the Sayan solar observatory (Irkutsk, Russia). The IRSOL observations are unique by allowing both the green and red line pairs to be recorded simultaneously on the same CCD sensor. We show how the line ratios depend on both the measured flux densities and on the heliocentric distance (the μ value on the solar disk), and finally derive the calibration function that enables the red line ratio to be translated to the green ratio for each μ value.

  13. Lethal combat and sex ratio evolution in a parasitoid wasp

    PubMed Central

    Innocent, Tabitha M.; Savage, Joanna; West, Stuart A.; Reece, Sarah E.

    2013-01-01

    Sex allocation theory provides excellent opportunities for testing how behavior and life histories are adjusted in response to environmental variation. One of the most successful areas from this respect is Hamilton’s local mate competition theory. As predicted by theory, a large number of animal species have been shown to adjust their offspring sex ratios (proportion male) conditionally, laying less female-biased sex ratios as the number of females that lay eggs on a patch increases. However, recent studies have shown that this predicted pattern is not followed by 2 parasitoid species in the genus Melittobia, which always produce extremely female-biased sex ratios. A possible explanation for this is that males fight fatally and that males produced by the first female to lay eggs on a patch have a competitive advantage over later emerging males. This scenario would negate the advantage of later females producing a less female-biased sex ratio. Here we examine fatal fighting and sex ratio evolution in another species, Melittobia acasta. We show that females of this species also fail to adjust their offspring sex ratio in response to the number of females laying eggs on a patch. We then show that although earlier emerging males do have an advantage in winning fights, this advantage 1) can be reduced by an interaction with body size, with larger males more likely to win fights and 2) only holds for a brief period around the time at which the younger males emerge from their pupae. This suggests that lethal male combat cannot fully explain the lack of sex ratio shift observed in Melittobia species. We discuss alternative explanations. PMID:24273326

  14. Lethal combat and sex ratio evolution in a parasitoid wasp.

    PubMed

    Innocent, Tabitha M; Savage, Joanna; West, Stuart A; Reece, Sarah E

    2007-07-01

    Sex allocation theory provides excellent opportunities for testing how behavior and life histories are adjusted in response to environmental variation. One of the most successful areas from this respect is Hamilton's local mate competition theory. As predicted by theory, a large number of animal species have been shown to adjust their offspring sex ratios (proportion male) conditionally, laying less female-biased sex ratios as the number of females that lay eggs on a patch increases. However, recent studies have shown that this predicted pattern is not followed by 2 parasitoid species in the genus Melittobia, which always produce extremely female-biased sex ratios. A possible explanation for this is that males fight fatally and that males produced by the first female to lay eggs on a patch have a competitive advantage over later emerging males. This scenario would negate the advantage of later females producing a less female-biased sex ratio. Here we examine fatal fighting and sex ratio evolution in another species, Melittobia acasta. We show that females of this species also fail to adjust their offspring sex ratio in response to the number of females laying eggs on a patch. We then show that although earlier emerging males do have an advantage in winning fights, this advantage 1) can be reduced by an interaction with body size, with larger males more likely to win fights and 2) only holds for a brief period around the time at which the younger males emerge from their pupae. This suggests that lethal male combat cannot fully explain the lack of sex ratio shift observed in Melittobia species. We discuss alternative explanations.

  15. Utilizing Isotopic Uranium Ratios in Groundwater Evaluations at FUSRAP Sites

    SciTech Connect

    Frederick, W.T.; Keil, K.G.; Rhodes, M.C.; Peterson, J.M.; MacDonell, M.M.

    2007-07-01

    The U.S. Army Corps of Engineers Buffalo District is evaluating environmental radioactive contamination at several Formerly Utilized Sites Remedial Action Program (FUSRAP) sites throughout New York, Pennsylvania, Ohio, and Indiana. The investigations follow the process defined in the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA). Groundwater data from the Niagara Falls Storage Site (NFSS) in Lewiston, New York were evaluated for isotopic uranium ratios, specifically uranium-234 versus uranium-238 (U- 234 and U-238, respectively), and the results were presented at Waste Management 2006. Since uranium naturally occurs in all groundwater, it can be difficult to distinguish where low-concentration impacts from past releases differ from the high end of a site-specific natural background range. In natural groundwater, the ratio of U-234 to U-238 exceeds 1 (unity) due to the alpha particle recoil effect, in which U-234 is preferentially mobilized to groundwater from adjacent rock or soil. This process is very slow and may take hundreds to thousands of years before a measurable increase is seen in the natural isotopic ratio. If site releases are the source of uranium being measured in groundwater, the U-234 to U-238 ratio is commonly closer to 1, which normally reflects FUSRAP-related, uranium-contaminated wastes and soils. This lower ratio occurs because not enough residence time has elapsed since the 1940's and 1950's for the alpha particle recoil effect to have significantly altered the contamination-derived ratio. An evaluation of NFSS-specific and regional groundwater data indicate that an isotopic ratio of 1.2 has been identified as a signature value to help distinguish natural groundwater, which may have a broad background range, from zones impacted by past releases. (authors)

  16. Multiple imputation for an incomplete covariate that is a ratio.

    PubMed

    Morris, Tim P; White, Ian R; Royston, Patrick; Seaman, Shaun R; Wood, Angela M

    2014-01-15

    We are concerned with multiple imputation of the ratio of two variables, which is to be used as a covariate in a regression analysis. If the numerator and denominator are not missing simultaneously, it seems sensible to make use of the observed variable in the imputation model. One such strategy is to impute missing values for the numerator and denominator, or the log-transformed numerator and denominator, and then calculate the ratio of interest; we call this 'passive' imputation. Alternatively, missing ratio values might be imputed directly, with or without the numerator and/or the denominator in the imputation model; we call this 'active' imputation. In two motivating datasets, one involving body mass index as a covariate and the other involving the ratio of total to high-density lipoprotein cholesterol, we assess the sensitivity of results to the choice of imputation model and, as an alternative, explore fully Bayesian joint models for the outcome and incomplete ratio. Fully Bayesian approaches using Winbugs were unusable in both datasets because of computational problems. In our first dataset, multiple imputation results are similar regardless of the imputation model; in the second, results are sensitive to the choice of imputation model. Sensitivity depends strongly on the coefficient of variation of the ratio's denominator. A simulation study demonstrates that passive imputation without transformation is risky because it can lead to downward bias when the coefficient of variation of the ratio's denominator is larger than about 0.1. Active imputation or passive imputation after log-transformation is preferable.

  17. Aspect ratio effect on shock-accelerated elliptic gas cylinders

    NASA Astrophysics Data System (ADS)

    Zou, Liyong; Liao, Shenfei; Liu, Cangli; Wang, Yanping; Zhai, Zhigang

    2016-03-01

    The evolution of an elliptic heavy-gas (SF6) cylinder accelerated by a planar weak shock wave is investigated experimentally using particle image velocimetry (PIV) diagnostics, and the emphasis is on the aspect ratio effect on shock-elliptic cylinder interaction. Experiments are conducted at five different aspect ratios (the ratio of length in streamwise and spanwise directions) varied from 0.25 to 4.0. PIV raw images and quantitative flow field data are obtained at t = 0.6 ms after the shock impact. As the aspect ratio increases, the interface morphology develops faster owing to more vorticity produced along the interface and smaller vortex spacing between the two vortex cores. For each case in this study, the maximal fluctuating velocity locates at the middle point of the two counter-vortices. The histograms of fluctuating velocity reveal that a distinct double-peak structure appears in the largest aspect ratio case in comparison with a single-peak structure in the smallest aspect ratio case. The vortex velocities predicted by the theoretical model [G. Rudinger and L. M. Somers, "Behaviour of small regions of different gases carried in accelerated gas flows," J. Fluid Mech. 7, 161-176 (1960)] agree well with the experimental ones. With the increase of aspect ratio, the maximal value of vorticity increases as well as the circulation, and more low-magnitude quantities are generated, which indicates the formation of multi-scale flow structure in the late mixing process. It is found that the experimental circulation of the vortex motion is reasonably estimated by the ideal point vortex-pair model.

  18. Prognostic Significance of Neutrophil to Lymphocyte Ratio, Lymphocyte to Monocyte Ratio, and Platelet to Lymphocyte Ratio in Patients with Nasopharyngeal Carcinoma

    PubMed Central

    Lu, Aiying; Li, Haifeng; Zheng, Yuming; Tang, Minzhong; Li, Jun; Wu, Huihui; Zhong, Weiming; Gao, Jianquan; Ou, Ningjiang

    2017-01-01

    The peripheral blood neutrophil to lymphocyte ratio (NLR), lymphocyte to monocyte ratio (LMR), and platelet to lymphocyte ratio (PLR) have been reported to correlate with the prognosis of many malignancies. This study evaluated the prognostic value of pretreatment NLR, LMR, and PLR in nasopharyngeal carcinoma (NPC). A retrospective analysis of clinical and pathological data of 140 NPC patients without distant metastasis during initial treatment was conducted to identify correlations between NLR, LMR, and PLR and clinicopathological features, overall survival, and progression-free survival. Cox proportional hazard regression analysis was used to reveal the independent factors affecting the prognosis of NPC patients. NLR was associated with T staging, N staging, and overall clinical stage grouping of the NPC patients (P < 0.05). NLR ≥ 2.28, LMR < 2.26, and PLR ≥ 174 were significantly associated with a relatively short overall survival (P < 0.05). In addition, NLR ≥ 2.28 was significantly associated with a relatively short progression-free survival (P < 0.05). Cox proportional hazard regression analysis showed that NLR was an independent prognostic factor in NPC. Pretreatment NLR, LMR, and PLR might be a useful complement to TNM staging in the prognostic assessment of NPC patients. PMID:28321405

  19. Reliability and interobserver variability in radiological patellar height ratios.

    PubMed

    Seil, R; Müller, B; Georg, T; Kohn, D; Rupp, S

    2000-01-01

    This study evaluated the reliability and interobserver variability of five patellar height ratios as measured by two examiners on standard radiographs: Insall-Salvati (IS), modified Insall-Salvati (MIS), Blackburne-Peel (BP), Caton-Deschamps (CD), and Labelle-Laurin (LL). Plain lateral radiographs with a knee flexion angle of 20 degrees for IS, MIS, BP, and CD ratios and 90 degrees for the LL method of 22 knees of 21 patients with varying pathological knee conditions were analyzed. Statistical results revealed a low interobserver variability with high correlation coefficients (0.86 for IS, 0.82 for MIS, 0.86 for BP, 0.92 for CD, and 0.81 for LL; P > 0.3) and low mean interobserver errors. However, regarding the reliability of the radiographic results of the different methods for patella alta, baja, or norma we found varying results in 68% of the patients. In two patients the patellar height was classified as alta, norma, or baja depending on the ratio used. Regarding the definitions of patellar height used by the authors of these methods, we found the lowest number of normal patellae with the IS ratio and no patella alta for the CD ratio. The LL method revealed the highest number of patella alta. The BP ratio showed intermediate results for both patella alta and baja, being the most moderate method. This study showed that there was a good interobserver reliability for the evaluation of patellar height according to the common radiological ratios. However, the high frequency of differing results between the different radiographic ratios showed that patellar height classification as "alta," "norma," or "baja" depends heavily on the chosen index. The differing results were due mainly to the normative patellar height data and to anatomical differences. Based on these findings we recommend a ratio using the articular surface of the patella in relation to the joint line. We recommend the BP method because it revealed the lowest interobserver variability and discriminated

  20. Combining Ratio Estimation for Low Density Parity Check (LDPC) Coding

    NASA Technical Reports Server (NTRS)

    Mahmoud, Saad; Hi, Jianjun

    2012-01-01

    The Low Density Parity Check (LDPC) Code decoding algorithm make use of a scaled receive signal derived from maximizing the log-likelihood ratio of the received signal. The scaling factor (often called the combining ratio) in an AWGN channel is a ratio between signal amplitude and noise variance. Accurately estimating this ratio has shown as much as 0.6 dB decoding performance gain. This presentation briefly describes three methods for estimating the combining ratio: a Pilot-Guided estimation method, a Blind estimation method, and a Simulation-Based Look-Up table. The Pilot Guided Estimation method has shown that the maximum likelihood estimates of signal amplitude is the mean inner product of the received sequence and the known sequence, the attached synchronization marker (ASM) , and signal variance is the difference of the mean of the squared received sequence and the square of the signal amplitude. This method has the advantage of simplicity at the expense of latency since several frames worth of ASMs. The Blind estimation method s maximum likelihood estimator is the average of the product of the received signal with the hyperbolic tangent of the product combining ratio and the received signal. The root of this equation can be determined by an iterative binary search between 0 and 1 after normalizing the received sequence. This method has the benefit of requiring one frame of data to estimate the combining ratio which is good for faster changing channels compared to the previous method, however it is computationally expensive. The final method uses a look-up table based on prior simulated results to determine signal amplitude and noise variance. In this method the received mean signal strength is controlled to a constant soft decision value. The magnitude of the deviation is averaged over a predetermined number of samples. This value is referenced in a look up table to determine the combining ratio that prior simulation associated with the average magnitude of