Science.gov

Sample records for airborne multispectral remote

  1. ASPIS, A Flexible Multispectral System for Airborne Remote Sensing Environmental Applications

    PubMed Central

    Papale, Dario; Belli, Claudio; Gioli, Beniamino; Miglietta, Franco; Ronchi, Cesare; Vaccari, Francesco Primo; Valentini, Riccardo

    2008-01-01

    Airborne multispectral and hyperspectral remote sensing is a powerful tool for environmental monitoring applications. In this paper we describe a new system (ASPIS) composed by a 4-CCD spectral sensor, a thermal IR camera and a laser altimeter that is mounted on a flexible Sky-Arrow airplane. A test application of the multispectral sensor to estimate durum wheat quality is also presented.

  2. An airborne multispectral imaging system based on two consumer-grade cameras for agricultural remote sensing

    Technology Transfer Automated Retrieval System (TEKTRAN)

    This paper describes the design and evaluation of an airborne multispectral imaging system based on two identical consumer-grade cameras for agricultural remote sensing. The cameras are equipped with a full-frame complementary metal oxide semiconductor (CMOS) sensor with 5616 × 3744 pixels. One came...

  3. Remote identification of potential boll weevil host plants: Airborne multispectral detection of regrowth cotton

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Regrowth cotton plants can serve as potential hosts for boll weevils during and beyond the production season. Effective methods for timely areawide detection of these host plants are critically needed to expedite eradication in south Texas. We acquired airborne multispectral images of experimental...

  4. Spatial Modeling and Variability Analysis for Modeling and Prediction of Soil and Crop Canopy Coverage Using Multispectral Imagery from an Airborne Remote Sensing System

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Based on a previous study on an airborne remote sensing system with automatic camera stabilization for crop management, multispectral imagery was acquired using the MS-4100 multispectral camera at different flight altitudes over a 115 ha cotton field. After the acquired images were geo-registered an...

  5. High Spatial Resolution Airborne Multispectral Thermal Infrared Remote Sensing Data for Analysis of Urban Landscape Characteristics

    NASA Technical Reports Server (NTRS)

    Quattrochi, Dale A.; Luvall, Jeffrey C.; Estes, Maurice G., Jr.; Arnold, James E. (Technical Monitor)

    2000-01-01

    We have used airborne multispectral thermal infrared (TIR) remote sensing data collected at a high spatial resolution (i.e., 10m) over several cities in the United States to study thermal energy characteristics of the urban landscape. These TIR data provide a unique opportunity to quantify thermal responses from discrete surfaces typical of the urban landscape and to identify both the spatial arrangement and patterns of thermal processes across the city. The information obtained from these data is critical to understanding how urban surfaces drive or force development of the Urban Heat Island (UHI) effect, which exists as a dome of elevated air temperatures that presides over cities in contrast to surrounding non-urbanized areas. The UHI is most pronounced in the summertime where urban surfaces, such as rooftops and pavement, store solar radiation throughout the day, and release this stored energy slowly after sunset creating air temperatures over the city that are in excess of 2-4'C warmer in contrast with non-urban or rural air temperatures. The UHI can also exist as a daytime phenomenon with surface temperatures in downtown areas of cities exceeding 38'C. The implications of the UHI are significant, particularly as an additive source of thermal energy input that exacerbates the overall production of ground level ozone over cities. We have used the Airborne Thermal and Land Applications Sensor (ATLAS), flown onboard a Lear 23 jet aircraft from the NASA Stennis Space Center, to acquire high spatial resolution multispectral TIR data (i.e., 6 bandwidths between 8.2-12.2 (um) over Huntsville, Alabama, Atlanta, Georgia, Baton Rouge, Louisiana, Salt Lake City, Utah, and Sacramento, California. These TIR data have been used to produce maps and other products, showing the spatial distribution of heating and cooling patterns over these cities to better understand how the morphology of the urban landscape affects development of the UHI. In turn, these data have been used

  6. Monitoring Ephemeral Streams Using Airborne Very High Resolution Multispectral Remote Sensing in Arid Environments

    NASA Astrophysics Data System (ADS)

    Hamada, Y.; O'Connor, B. L.

    2012-12-01

    Development in arid environments often results in the loss and degradation of the ephemeral streams that provide habitat and critical ecosystem functions such as water delivery, sediment transport, and groundwater recharge. Quantification of these ecosystem functions is challenging because of the episodic nature of runoff events in desert landscapes and the large spatial scale of watersheds that potentially can be impacted by large-scale development. Low-impact development guidelines and regulatory protection of ephemeral streams are often lacking due to the difficulty of accurately mapping and quantifying the critical functions of ephemeral streams at scales larger than individual reaches. Renewable energy development in arid regions has the potential to disturb ephemeral streams at the watershed scale, and it is necessary to develop environmental monitoring applications for ephemeral streams to help inform land management and regulatory actions aimed at protecting and mitigating for impacts related to large-scale land disturbances. This study focuses on developing remote sensing methodologies to identify and monitor impacts on ephemeral streams resulting from the land disturbance associated with utility-scale solar energy development in the desert southwest of the United States. Airborne very high resolution (VHR) multispectral imagery is used to produce stereoscopic, three-dimensional landscape models that can be used to (1) identify and map ephemeral stream channel networks, and (2) support analyses and models of hydrologic and sediment transport processes that pertain to the critical functionality of ephemeral streams. Spectral and statistical analyses are being developed to extract information about ephemeral channel location and extent, micro-topography, riparian vegetation, and soil moisture characteristics. This presentation will demonstrate initial results and provide a framework for future work associated with this project, for developing the necessary

  7. An algorithm for the estimation of water temperatures from thermal multispectral airborne remotely sensed data

    NASA Technical Reports Server (NTRS)

    Jaggi, S.; Quattrochi, D.; Baskin, R.

    1992-01-01

    A method for water temperature estimation on the basis of thermal data is presented and tested against NASA's Thermal IR Multispectral Scanner. Using realistic bounds on emissivities, temperature bounds are calculated and refined to estimate a tighter bound on the emissivity of the source. The method is useful only when a realistic set of bounds can be obtained for the emissivities of the data.

  8. Recent advances in airborne terrestrial remote sensing with the NASA airborne visible/infrared imaging spectrometer (AVIRIS), airborne synthetic aperture radar (SAR), and thermal infrared multispectral scanner (TIMS)

    NASA Technical Reports Server (NTRS)

    Vane, Gregg; Evans, Diane L.; Kahle, Anne B.

    1989-01-01

    Significant progress in terrestrial remote sensing from the air has been made with three NASA-developed sensors that collectively cover the solar-reflected, thermal infrared, and microwave regions of the electromagnetic spectrum. These sensors are the airborne visible/infrared imaging spectrometer (AVIRIS), the thermal infrared mapping spectrometer (TIMS) and the airborne synthetic aperture radar (SAR), respectively. AVIRIS and SAR underwent extensive in-flight engineering testing in 1987 and 1988 and are scheduled to become operational in 1989. TIMS has been in operation for several years. These sensors are described.

  9. Airborne multispectral and hyperspectral remote sensing: Examples of applications to the study of environmental and engineering problems

    SciTech Connect

    Bianchi, R.; Marino, C.M.

    1997-10-01

    The availability of a new aerial survey capability carried out by the CNR/LARA (National Research Council - Airborne Laboratory for the Environmental Research) by a new spectroradiometer AA5000 MIVIS (Multispectral Infrared and Visible Imaging Spectrometer) on board a CASA 212/200 aircraft, enable the scientists to obtain innovative data sets, for different approach to the definitions and the understanding of a variety of environmental and engineering problems. The 102 MIVIS channels spectral bandwidths are chosen to meet the needs of scientific research for advanced applications of remote sensing data. In such configuration MIVIS can offer significant contributions to problem solving in wide sectors such as geologic exploration, agricultural crop studies, forestry, land use mapping, idrogeology, oceanography and others. LARA in 1994-96 has been active over different test-sites in joint-venture with JPL, Pasadena, different European Institutions and Italian University and Research Institutes. These aerial surveys allow the national and international scientific community to approach the use of Hyperspectral Remote Sensing in environmental problems of very large interest. The sites surveyed in Italy, France and Germany include a variety of targets such as quarries, landfills, karst cavities areas, landslides, coastlines, geothermal areas, etc. The deployments gathered up to now more than 300 GBytes of MIVIS data in more than 30 hours of VLDS data recording. The purpose of this work is to present and to comment the procedures and the results at research and at operational level of the past campaigns with special reference to the study of environmental and engineering problems.

  10. Highly Protable Airborne Multispectral Imaging System

    NASA Technical Reports Server (NTRS)

    Lehnemann, Robert; Mcnamee, Todd

    2001-01-01

    A portable instrumentation system is described that includes and airborne and a ground-based subsytem. It can acquire multispectral image data over swaths of terrain ranging in width from about 1.5 to 1 km. The system was developed especially for use in coastal environments and is well suited for performing remote sensing and general environmental monitoring. It includes a small,munpilotaed, remotely controlled airplance that carries a forward-looking camera for navigation, three downward-looking monochrome video cameras for imaging terrain in three spectral bands, a video transmitter, and a Global Positioning System (GPS) reciever.

  11. Airborne Multispectral and Thermal Remote Sensing for Detecting the Onset of Crop Stress Caused by Multiple Factors

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Remote sensing technology has been developed and applied to provide spatiotemporal information on crop stress for precision management. A series of multispectral images over a field planted cotton, corn and soybean were obtained by a Geospatial Systems MS4100 camera mounted on an Air Tractor 402B ai...

  12. Airborne multi-spectral remote sensing with ground truth for areawide pest management

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Scientists and researchers have been developing, integrating, and evaluating multiple strategies and technologies into a systems approach for management of field crop insect pests. Remote sensing along with Global Positioning Systems, Geographic Information Systems, and variable rate technology are...

  13. Airborne multispectral remote sensing with ground truth for areawide pest management

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Scientists and engineers in areawide pest management programs have been developing, integrating, and evaluating multiple strategies and technologies into a systems approach for management of field crop insect pests. Remote sensing along with global positioning systems, geographic information system...

  14. Multispectral Imaging Systems for Airborne Remote Sensing to Support Site-Specific Agricultural Management

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Remote sensing has shown promise as a tool for site-specific management in agricultural application and production. Earth-observing satellite systems have an advantage for large-scale analysis at regional levels but are limited in spatial resolution. High-resolution satellite systems have been avail...

  15. Multispectral Imaging Systems for Airborne Remote Sensing to Support Agricultural Production Management

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Remote sensing has shown promise as a tool for managing agricultural application and production. Earth-observing satellite systems have an advantage for large-scale analysis at regional levels but are limited in spatial resolution. High-resolution satellite systems have been available in recent year...

  16. Airborne multispectral remote sensing data to estimate several oenological parameters in vineyard production. A case study of application of remote sensing data to precision viticulture in central Italy.

    NASA Astrophysics Data System (ADS)

    Tramontana, Gianluca; Girard, Filippo; Belli, Claudio; Comandini, Maria Cristina; Pietromarchi, Paolo; Tiberi, Domenico; Papale, Dario

    2010-05-01

    It is widely recognized that environmental differences within the vineyard, with respect to soils, microclimate, and topography, can influence grape characteristics and crop yields. Besides, the central Italy landscape is characterized by a high level of fragmentation and heterogeneity It requires stringent Remote sensing technical features in terms of spectral, geometric and temporal resolution to aimed at supporting applications for precision viticulture. In response to the needs of the Italian grape and wine industry for an evaluation of precision viticulture technologies, the DISAFRI (University of Tuscia) and the Agricultural Research Council - Oenological research unit (ENC-CRA) jointly carried out an experimental study during the year 2008. The study was carried out on 2 areas located in the town of Velletri, near Rome; for each area, two varieties (red and white grape) were studied: Nero d'Avola and Sauvignon blanc in first area , Merlot and Sauvignon blanc in second. Remote sensing data were acquired in different periods using a low cost multisensor Airborne remote sensing platform developed by DISAFRI (ASPIS-2 Advanced Spectroscopic Imager System). ASPIS-2, an evolution of the ASPIS sensor (Papale et al 2008, Sensors), is a multispectral sensor based on 4 CCD and 3 interferential filters per CCD. The filters are user selectable during the flight and in this way Aspis is able to acquire data in 12 bands in the visible and near infrared regions with a bandwidth of 10 or 20 nm. To the purposes of this study 7 spectral band were acquired and 15 vegetation indices calculated. During the ripeness period several vegetative and oenochemical parameters were monitored. Anova test shown that several oenochemical variables, such as sugars, total acidity, polyphenols and anthocyanins differ according to the variety taken into consideration. In order to evaluate the time autocorrelation of several oenological parameters value, a simple linear regression between

  17. Airborne multispectral and thermal remote sensing for detecting the onset of crop stress caused by multiple factors

    NASA Astrophysics Data System (ADS)

    Huang, Yanbo; Thomson, Steven J.

    2010-10-01

    Remote sensing technology has been developed and applied to provide spatiotemporal information on crop stress for precision management. A series of multispectral images over a field planted cotton, corn and soybean were obtained by a Geospatial Systems MS4100 camera mounted on an Air Tractor 402B airplane equipped with Camera Link in a Magma converter box triggered by Terraverde Dragonfly® flight navigation and imaging control software. The field crops were intentionally stressed by applying glyphosate herbicide via aircraft and allowing it to drift near-field. Aerial multispectral images in the visible and near-infrared bands were manipulated to produce vegetation indices, which were used to quantify the onset of herbicide induced crop stress. The vegetation indices normalized difference vegetation index (NDVI) and soil adjusted vegetation index (SAVI) showed the ability to monitor crop response to herbicide-induced injury by revealing stress at different phenological stages. Two other fields were managed with irrigated versus nonirrigated treatments, and those fields were imaged with both the multispectral system and an Electrophysics PV-320T thermal imaging camera on board an Air Tractor 402B aircraft. Thermal imagery indicated water stress due to deficits in soil moisture, and a proposed method of determining crop cover percentage using thermal imagery was compared with a multispectral imaging method. Development of an image fusion scheme may be necessary to provide synergy and improve overall water stress detection ability.

  18. FireMapper 2.0: a multispectral uncooled infrared imaging system for airborne wildfire mapping and remote sensing

    NASA Astrophysics Data System (ADS)

    Hoffman, James W.; Riggan, Philip J.; Griffin, Stephanie A.; Grush, Ronald C.; Grush, William H.; Pena, James

    2003-11-01

    FireMapper®2.0 is a second-generation airborne system developed specifically for wildfire mapping and remote sensing. Its design is based on lessons learned from two years of flight-testing of a research FireMapper® system by the Pacific uthwest Research Station of the USDA Forest Service. The new, operational design features greater coverage and improved performance with a rugged sensor that is less than one third the size and weight of the original research sensor. The sensor obtains thermal infrared images in two narrow spectral bands and one wide spectral band with the use of a single uncooled microbolometer detector array. The dynamic range of the sensor is designed to accurately measure scene temperatures from normal backgrounds, for remote sensing and disaster management applications, up to flaming fronts without saturating. All three channels are extremely linear and are calibrated in-flight with a highly accurate absolute calibration system. Airborne testing of the research system has led to improved displays and simplified operator interfaces. These features facilitate the operational use of the FireMapper®2.0 system on both fixed wing aircraft and helicopters with minimal operator inputs. The operating system features custom software to display and zoom in on the images in realtime as they are obtained. Selected images can also be saved and recalled for detailed study. All images are tagged with GPS date, time, latitude, longitude, altitude, and heading and can be recorded on a portable USB hard drive upon operator command. The operating system can also be used to replay previously recorded image sequences. The FireMapper® 2.0 was designed and fabricated by Space Instruments, Inc. as part of a Research Joint Venture with the USDA Forest Service.

  19. Remote Multispectral Imaging of Wildland Fires (Invited)

    NASA Astrophysics Data System (ADS)

    Vodacek, A.; Kremens, R.

    2010-12-01

    Wildland fires produce a variety of signal phenomenology that are remotely observable. These signals span a large portion of the electromagnetic spectrum and can be related to a variety of properties of wildland fires as they propagate. The deployment of multispectral sensors from aircraft provides a unique perspective on the fire and its interactions in the environment by repeated imaging over time. We describe a set of airborne imaging experiments, image processing methodologies and a workflow system for near real-time extraction of information on the fire and the immediate environment.

  20. An algorithm for the estimation of bounds on the emissivity and temperatures from thermal multispectral airborne remotely sensed data

    NASA Technical Reports Server (NTRS)

    Jaggi, S.; Quattrochi, D.; Baskin, R.

    1992-01-01

    The effective flux incident upon the detectors of a thermal sensor, after it has been corrected for atmospheric effects, is a function of a non-linear combination of the emissivity of the target for that channel and the temperature of the target. The sensor system cannot separate the contribution from the emissivity and the temperature that constitute the flux value. A method that estimates the bounds on these temperatures and emissivities from thermal data is described. This method is then tested with remotely sensed data obtained from NASA's Thermal Infrared Multispectral Scanner (TIMS) - a 6 channel thermal sensor. Since this is an under-determined set of equations i.e. there are 7 unknowns (6 emissivities and 1 temperature) and 6 equations (corresponding to the 6 channel fluxes), there exist theoretically an infinite combination of values of emissivities and temperature that can satisfy these equations. Using some realistic bounds on the emissivities, bounds on the temperature are calculated. These bounds on the temperature are refined to estimate a tighter bound on the emissivity of the source. An error analysis is also carried out to quantitatively determine the extent of uncertainty introduced in the estimate of these parameters. This method is useful only when a realistic set of bounds can be obtained for the emissivities of the data. In the case of water the lower and upper bounds were set at 0.97 and 1.00 respectively. Five flights were flown in succession at altitudes of 2 km (low), 6 km (mid), 12 km (high), and then back again at 6 km and 2 km. The area selected with the Ross Barnett reservoir near Jackson, Mississippi. The mission was flown during the predawn hours of 1 Feb. 1992. Radiosonde data was collected for that duration to profile the characteristics of the atmosphere. Ground truth temperatures using thermometers and radiometers were also obtained over an area of the reservoir. The results of two independent runs of the radiometer data averaged

  1. Airborne multispectral detection of regrowth cotton fields

    NASA Astrophysics Data System (ADS)

    Westbrook, John K.; Suh, Charles P.-C.; Yang, Chenghai; Lan, Yubin; Eyster, Ritchie S.

    2015-01-01

    Effective methods are needed for timely areawide detection of regrowth cotton plants because boll weevils (a quarantine pest) can feed and reproduce on these plants beyond the cotton production season. Airborne multispectral images of regrowth cotton plots were acquired on several dates after three shredding (i.e., stalk destruction) dates. Linear spectral unmixing (LSU) classification was applied to high-resolution airborne multispectral images of regrowth cotton plots to estimate the minimum detectable size and subsequent growth of plants. We found that regrowth cotton fields can be identified when the mean plant width is ˜0.2 m for an image resolution of 0.1 m. LSU estimates of canopy cover of regrowth cotton plots correlated well (r2=0.81) with the ratio of mean plant width to row spacing, a surrogate measure of plant canopy cover. The height and width of regrowth plants were both well correlated (r2=0.94) with accumulated degree-days after shredding. The results will help boll weevil eradication program managers use airborne multispectral images to detect and monitor the regrowth of cotton plants after stalk destruction, and identify fields that may require further inspection and mitigation of boll weevil infestations.

  2. Airborne system for testing multispectral reconnaissance technologies

    NASA Astrophysics Data System (ADS)

    Schmitt, Dirk-Roger; Doergeloh, Heinrich; Keil, Heiko; Wetjen, Wilfried

    1999-07-01

    There is an increasing demand for future airborne reconnaissance systems to obtain aerial images for tactical or peacekeeping operations. Especially Unmanned Aerial Vehicles (UAVs) equipped with multispectral sensor system and with real time jam resistant data transmission capabilities are of high interest. An airborne experimental platform has been developed as testbed to investigate different concepts of reconnaissance systems before their application in UAVs. It is based on a Dornier DO 228 aircraft, which is used as flying platform. Great care has been taken to achieve the possibility to test different kinds of multispectral sensors. Hence basically it is capable to be equipped with an IR sensor head, high resolution aerial cameras of the whole optical spectrum and radar systems. The onboard equipment further includes system for digital image processing, compression, coding, and storage. The data are RF transmitted to the ground station using technologies with high jam resistance. The images, after merging with enhanced vision components, are delivered to the observer who has an uplink data channel available to control flight and imaging parameters.

  3. Deepwater Horizon oil spill monitoring using airborne multispectral infrared imagery

    NASA Astrophysics Data System (ADS)

    Shen, Sylvia S.; Lewis, Paul E.

    2011-06-01

    On April 28, 2010, the Environmental Protection Agency's (EPA) Airborne Spectral Photometric Environmental Collection Technology (ASPECT) aircraft was deployed to Gulfport, Mississippi to provide airborne remotely sensed air monitoring and situational awareness data and products in response to the Deepwater Horizon oil spill disaster. The ASPECT aircraft was released from service on August 9, 2010 after having flown over 85 missions that included over 325 hours of flight operation. This paper describes several advanced analysis capabilities specifically developed for the Deepwater Horizon mission to correctly locate, identify, characterize, and quantify surface oil using ASPECT's multispectral infrared data. The data products produced using these advanced analysis capabilities provided the Deepwater Horizon Incident Command with a capability that significantly increased the effectiveness of skimmer vessel oil recovery efforts directed by the U.S. Coast Guard, and were considered by the Incident Command as key situational awareness information.

  4. Sandia Multispectral Airborne Lidar for UAV Deployment

    SciTech Connect

    Daniels, J.W.; Hargis,Jr. P.J.; Henson, T.D.; Jordan, J.D.; Lang, A.R.; Schmitt, R.L.

    1998-10-23

    Sandia National Laboratories has initiated the development of an airborne system for W laser remote sensing measurements. System applications include the detection of effluents associated with the proliferation of weapons of mass destruction and the detection of biological weapon aerosols. This paper discusses the status of the conceptual design development and plans for both the airborne payload (pointing and tracking, laser transmitter, and telescope receiver) and the Altus unmanned aerospace vehicle platform. Hardware design constraints necessary to maintain system weight, power, and volume limitations of the flight platform are identified.

  5. Remote Sensing of Liquid Water and Ice Cloud Optical Thickness and Effective Radius in the Arctic: Application of Airborne Multispectral MAS Data

    NASA Technical Reports Server (NTRS)

    King, Michael D.; Platnick, Steven; Yang, Ping; Arnold, G. Thomas; Gray, Mark A.; Riedi, Jerome C.; Ackerman, Steven A.; Liou, Kuo-Nan

    2003-01-01

    A multispectral scanning spectrometer was used to obtain measurements of the reflection function and brightness temperature of clouds, sea ice, snow, and tundra surfaces at 50 discrete wavelengths between 0.47 and 14.0 microns. These observations were obtained from the NASA ER-2 aircraft as part of the FIRE Arctic Clouds Experiment, conducted over a 1600 x 500 km region of the north slope of Alaska and surrounding Beaufort and Chukchi Seas between 18 May and 6 June 1998. Multispectral images of the reflection function and brightness temperature in 11 distinct bands of the MODIS Airborne Simulator (MAS) were used to derive a confidence in clear sky (or alternatively the probability of cloud), shadow, and heavy aerosol over five different ecosystems. Based on the results of individual tests run as part of the cloud mask, an algorithm was developed to estimate the phase of the clouds (water, ice, or undetermined phase). Finally, the cloud optical thickness and effective radius were derived for both water and ice clouds that were detected during one flight line on 4 June. This analysis shows that the cloud mask developed for operational use on MODIS, and tested using MAS data in Alaska, is quite capable of distinguishing clouds from bright sea ice surfaces during daytime conditions in the high Arctic. Results of individual tests, however, make it difficult to distinguish ice clouds over snow and sea ice surfaces, so additional tests were added to enhance the confidence in the thermodynamic phase of clouds over the Beaufort Sea. The cloud optical thickness and effective radius retrievals used 3 distinct bands of the MAS, with the newly developed 1.62 and 2.13 micron bands being used quite successfully over snow and sea ice surfaces. These results are contrasted with a MODIS-based algorithm that relies on spectral reflectance at 0.87 and 2.13 micron.

  6. Study on airborne multispectral imaging fusion detection technology

    NASA Astrophysics Data System (ADS)

    Ding, Na; Gao, Jiaobo; Wang, Jun; Cheng, Juan; Gao, Meng; Gao, Fei; Fan, Zhe; Sun, Kefeng; Wu, Jun; Li, Junna; Gao, Zedong; Cheng, Gang

    2014-11-01

    The airborne multispectral imaging fusion detection technology is proposed in this paper. In this design scheme, the airborne multispectral imaging system consists of the multispectral camera, the image processing unit, and the stabilized platform. The multispectral camera can operate in the spectral region from visible to near infrared waveband (0.4-1.0um), it has four same and independent imaging channels, and sixteen different typical wavelengths to be selected based on the different typical targets and background. The related experiments were tested by the airborne multispectral imaging system. In particularly, the camouflage targets were fused and detected in the different complex environment, such as the land vegetation background, the desert hot background and underwater. In the spectral region from 0.4 um to 1.0um, the three different characteristic wave from sixteen typical spectral are selected and combined according to different backgrounds and targets. The spectral image corresponding to the three characteristic wavelengths is resisted and fused by the image processing technology in real time, and the fusion video with typical target property is outputted. In these fusion images, the contrast of target and background is greatly increased. Experimental results confirm that the airborne multispectral imaging fusion detection technology can acquire multispectral fusion image with high contrast in real time, and has the ability of detecting and identification camouflage objects from complex background to targets underwater.

  7. Airborne system for multispectral, multiangle polarimetric imaging.

    PubMed

    Bowles, Jeffrey H; Korwan, Daniel R; Montes, Marcos J; Gray, Deric J; Gillis, David B; Lamela, Gia M; Miller, W David

    2015-11-01

    In this paper, we describe the design, fabrication, calibration, and deployment of an airborne multispectral polarimetric imager. The motivation for the development of this instrument was to explore its ability to provide information about water constituents, such as particle size and type. The instrument is based on four 16 MP cameras and uses wire grid polarizers (aligned at 0°, 45°, 90°, and 135°) to provide the separation of the polarization states. A five-position filter wheel provides for four narrow-band spectral filters (435, 550, 625, and 750 nm) and one blocked position for dark-level measurements. When flown, the instrument is mounted on a programmable stage that provides control of the view angles. View angles that range to ±65° from the nadir have been used. Data processing provides a measure of the polarimetric signature as a function of both the view zenith and view azimuth angles. As a validation of our initial results, we compare our measurements, over water, with the output of a Monte Carlo code, both of which show neutral points off the principle plane. The locations of the calculated and measured neutral points are compared. The random error level in the measured degree of linear polarization (8% at 435) is shown to be better than 0.25%. PMID:26560615

  8. Development of an airborne remote sensing system for aerial applicators

    Technology Transfer Automated Retrieval System (TEKTRAN)

    An airborne remote sensing system was developed and tested for recording aerial images of field crops, which were analyzed for variations of crop health or pest infestation. The multicomponent system consists of a multi-spectral camera system, a camera control system, and a radiometer for normalizi...

  9. Multispectral Airborne Laser Scanning for Automated Map Updating

    NASA Astrophysics Data System (ADS)

    Matikainen, Leena; Hyyppä, Juha; Litkey, Paula

    2016-06-01

    During the last 20 years, airborne laser scanning (ALS), often combined with multispectral information from aerial images, has shown its high feasibility for automated mapping processes. Recently, the first multispectral airborne laser scanners have been launched, and multispectral information is for the first time directly available for 3D ALS point clouds. This article discusses the potential of this new single-sensor technology in map updating, especially in automated object detection and change detection. For our study, Optech Titan multispectral ALS data over a suburban area in Finland were acquired. Results from a random forests analysis suggest that the multispectral intensity information is useful for land cover classification, also when considering ground surface objects and classes, such as roads. An out-of-bag estimate for classification error was about 3% for separating classes asphalt, gravel, rocky areas and low vegetation from each other. For buildings and trees, it was under 1%. According to feature importance analyses, multispectral features based on several channels were more useful that those based on one channel. Automatic change detection utilizing the new multispectral ALS data, an old digital surface model (DSM) and old building vectors was also demonstrated. Overall, our first analyses suggest that the new data are very promising for further increasing the automation level in mapping. The multispectral ALS technology is independent of external illumination conditions, and intensity images produced from the data do not include shadows. These are significant advantages when the development of automated classification and change detection procedures is considered.

  10. Unsupervised classification of remote multispectral sensing data

    NASA Technical Reports Server (NTRS)

    Su, M. Y.

    1972-01-01

    The new unsupervised classification technique for classifying multispectral remote sensing data which can be either from the multispectral scanner or digitized color-separation aerial photographs consists of two parts: (a) a sequential statistical clustering which is a one-pass sequential variance analysis and (b) a generalized K-means clustering. In this composite clustering technique, the output of (a) is a set of initial clusters which are input to (b) for further improvement by an iterative scheme. Applications of the technique using an IBM-7094 computer on multispectral data sets over Purdue's Flight Line C-1 and the Yellowstone National Park test site have been accomplished. Comparisons between the classification maps by the unsupervised technique and the supervised maximum liklihood technique indicate that the classification accuracies are in agreement.

  11. Hyperspectral and multispectral sensors for remote sensing

    NASA Astrophysics Data System (ADS)

    Miller, James; Kullar, Sukhbir; Cochrane, David; O, Nixon; Lomako, Andrey; Draijer, Cees

    2010-11-01

    Remote Hyperspectral and Multispectral sensors have been developed using modern CCD and CMOS fabrication techniques combined with advanced dichroic filters. The resulting sensors are more cost effective while maintaining the high performance needed in remote sensing applications. A single device can contain multiple imaging areas tailored to different multispectral bandwidths in a highly cost effective and reliable package. This paper discusses a five band visible to near IR scanning sensor. By bonding advanced dichroic filters onto the cover glass and directly in the imaging path a highly efficient multispectral sensor is achieved. Up to 12,000 linear pixel arrays are possible1 with this advanced filter technology approach. Individual imaging areas on the device are designed to have unique pixel sizes and clocking to enable tailored imaging performance for the individual spectral bands. Individual elements are also based on high resolution Time Delay and Integration technology2,3 (TDI) to maximize sensitivity and throughput. Additionally for hyperspectral imagers, a split frame CCD design is discussed using high sensitivity back side illuminated (BSI) processes that can achieve high quantum efficiency. As these sensors are used in remote sensing applications, device robustness and radiation tolerance was required.

  12. Citrus greening detection using airborne hyperspectral and multispectral imaging techniques

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Hyperspectral imaging can provide unique spectral signatures for diseased vegetation. Airborne multispectral and hyperspectral imaging can be used to detect potentially infected trees over a large area for rapid detection of infected zones. This paper proposes a method to detect the citrus greening...

  13. Airborne Remote Sensing

    NASA Technical Reports Server (NTRS)

    1992-01-01

    NASA imaging technology has provided the basis for a commercial agricultural reconnaissance service. AG-RECON furnishes information from airborne sensors, aerial photographs and satellite and ground databases to farmers, foresters, geologists, etc. This service produces color "maps" of Earth conditions, which enable clients to detect crop color changes or temperature changes that may indicate fire damage or pest stress problems.

  14. Atmospheric effects in multispectral remote sensor data

    NASA Technical Reports Server (NTRS)

    Turner, R. E.

    1975-01-01

    The problem of radiometric variations in multispectral remote sensing data which occur as a result of a change in geometric and environmental factors is studied. The case of spatially varying atmospheres is considered and the effect of atmospheric scattering is analyzed for realistic conditions. Emphasis is placed upon a simulation of LANDSAT spectral data for agricultural investigations over the United States. The effect of the target-background interaction is thoroughly analyzed in terms of various atmospheric states, geometric parameters, and target-background materials. Results clearly demonstrate that variable atmospheres can alter the classification accuracy and that the presence of various backgrounds can change the effective target radiance by a significant amount. A failure to include these effects in multispectral data analysis will result in a decrease in the classification accuracy.

  15. Airborne multispectral detecting system for marine mammals survey

    NASA Astrophysics Data System (ADS)

    Podobna, Yuliya; Sofianos, James; Schoonmaker, Jon; Medeiros, Dustin; Boucher, Cynthia; Oakley, Daniel; Saggese, Steve

    2010-04-01

    This work presents an electro-optical multispectral capability that detects and monitors marine mammals. It is a continuance of Whale Search Radar SBIR program funded by PMA-264 through NAVAIR. A lightweight, multispectral, turreted imaging system is designed for airborne and ship based platforms to detect and monitor marine mammals. The system tests were conducted over the Humpback whale breeding and calving area in Maui, Hawaii. The results of the tests and the system description are presented. The development of an automatic whale detection algorithm is discussed as well as methodology used to turn raw survey data into quantifiable data products.

  16. Evaluation of eelgrass beds mapping using a high-resolution airborne multispectral scanner

    USGS Publications Warehouse

    Su, H.; Karna, D.; Fraim, E.; Fitzgerald, M.; Dominguez, R.; Myers, J.S.; Coffland, B.; Handley, L.R.; Mace, T.

    2006-01-01

    Eelgrass (Zostera marina) can provide vital ecological functions in stabilizing sediments, influencing current dynamics, and contributing significant amounts of biomass to numerous food webs in coastal ecosystems. Mapping eelgrass beds is important for coastal water and nearshore estuarine monitoring, management, and planning. This study demonstrated the possible use of high spatial (approximately 5 m) and temporal (maximum low tide) resolution airborne multispectral scanner on mapping eelgrass beds in Northern Puget Sound, Washington. A combination of supervised and unsupervised classification approaches were performed on the multispectral scanner imagery. A normalized difference vegetation index (NDVI) derived from the red and near-infrared bands and ancillary spatial information, were used to extract and mask eelgrass beds and other submerged aquatic vegetation (SAV) in the study area. We evaluated the resulting thematic map (geocoded, classified image) against a conventional aerial photograph interpretation using 260 point locations randomly stratified over five defined classes from the thematic map. We achieved an overall accuracy of 92 percent with 0.92 Kappa Coefficient in the study area. This study demonstrates that the airborne multispectral scanner can be useful for mapping eelgrass beds in a local or regional scale, especially in regions for which optical remote sensing from space is constrained by climatic and tidal conditions. ?? 2006 American Society for Photogrammetry and Remote Sensing.

  17. Multispectral remote sensing as stratigraphic and structural tool, Wind River Basin and Big Horn Basin areas, Wyoming

    SciTech Connect

    Lang, H.R.; Adams, S.L.; Conel, J.E.; Mcguffie, B.A.; Paylor, E.D.; Walker, R.E.

    1987-04-01

    The use of Landsat TM, Airborne Imaging Spectrometer, and airborne Thermal IR Multispectral Scanner data in the geological evaluation of two sites in central Wyoming is described and illustrated with diagrams, maps, photographs, sample images, and tables of numerical data. The value of the remotely sensed information on the areal variation of attitude, sequence, thickness, and lithology of exposed strata is demonstrated; details of the data analysis are given; and the specialized software packages employed are briefly characterized. 46 references.

  18. Multispectral microwave imaging radar for remote sensing applications

    NASA Technical Reports Server (NTRS)

    Larson, R. W.; Rawson, R.; Ausherman, D.; Bryan, L.; Porcello, L.

    1974-01-01

    A multispectral airborne microwave radar imaging system, capable of obtaining four images simultaneously is described. The system has been successfully demonstrated in several experiments and one example of results obtained, fresh water ice, is given. Consideration of the digitization of the imagery is given and an image digitizing system described briefly. Preliminary results of digitization experiments are included.

  19. A high-resolution airborne four-camera imaging system for agricultural remote sensing

    Technology Transfer Automated Retrieval System (TEKTRAN)

    This paper describes the design and testing of an airborne multispectral digital imaging system for remote sensing applications. The system consists of four high resolution charge coupled device (CCD) digital cameras and a ruggedized PC equipped with a frame grabber and image acquisition software. T...

  20. Daily evapotranspiration estimates from extrapolating instantaneous airborne remote sensing ET values

    Technology Transfer Automated Retrieval System (TEKTRAN)

    In this study, six extrapolation methods have been compared for their ability to estimate daily crop evapotranspiration (ETd) from instantaneous latent heat flux estimates derived from digital airborne multispectral remote sensing imagery. Data used in this study were collected during an experiment...

  1. Multispectral airborne laser scanning - a new trend in the development of LiDAR technology

    NASA Astrophysics Data System (ADS)

    Bakuła, K.

    2015-12-01

    Airborne laser scanning (ALS) is the one of the most accurate remote sensing techniques for data acquisition where the terrain and its coverage is concerned. Modern scanners have been able to scan in two or more channels (frequencies of the laser) recently. This gives the rise to the possibility of obtaining diverse information about an area with the different spectral properties of objects. The paper presents an example of a multispectral ALS system - Titan by Optech - with the possibility of data including the analysis of digital elevation models accuracy and data density. As a result of the study, the high relative accuracy of LiDAR acquisition in three spectral bands was proven. The mean differences between digital terrain models (DTMs) were less than 0.03 m. The data density analysis showed the influence of the laser wavelength. The points clouds that were tested had average densities of 25, 23 and 20 points per square metre respectively for green (G), near-infrared (NIR) and shortwave-infrared (SWIR) lasers. In this paper, the possibility of the generation of colour composites using orthoimages of laser intensity reflectance and its classification capabilities using data from airborne multispectral laser scanning for land cover mapping are also discussed and compared with conventional photogrammetric techniques.

  2. Multispectral thermal airborne TASI-600 data to study the Pompeii (IT) archaeological area

    NASA Astrophysics Data System (ADS)

    Palombo, Angelo; Pascucci, Simone; Pergola, Nicola; Pignatti, Stefano; Santini, Federico; Soldovieri, Francesco

    2016-04-01

    The management of archaeological areas refers to the conservation of the ruins/buildings and the eventual prospection of new areas having an archaeological potential. In this framework, airborne remote sensing is a well-developed geophysical tool for supporting the archaeological surveys of wide areas. The spectral regions applied in archaeological remote sensing spans from the VNIR to the TIR. In particular, the archaeological thermal imaging considers that materials absorb, emit, transmit, and reflect the thermal infrared radiation at different rate according to their composition, density and moisture content. Despite its potential, thermal imaging in archaeological applications are scarce. Among them, noteworthy are the ones related to the use of Landsat and ASTER [1] and airborne remote sensing [2, 3, 4 and 5]. In view of these potential in Cultural Heritage applications, the present study aims at analysing the usefulness of the high spatial resolution thermal imaging on the Pompeii archaeological park. To this purpose TASI-600 [6] airborne multispectral thermal imagery (32 channels from 8 to 11.5 nm with a spectral resolution of 100nm and a spatial resolution of 1m/pixel) was acquired on December the 7th, 2015. Airborne survey has been acquired to get useful information on the building materials (both ancient and of consolidation) characteristics and, whenever possible, to retrieve quick indicators on their conservation status. Thermal images will be, moreover, processed to have an insight of the critical environmental issues impacting the structures (e.g. moisture). The proposed study shows the preliminary results of the airborne deployments, the pre-processing of the multispectral thermal imagery and the retrieving of accurate land surface temperatures (LST). LST map will be analysed to describe the thermal pattern of the city of Pompeii and detect any thermal anomalies. As far as the ongoing TASI-600 sensors pre-processing, it will include: (a) radiometric

  3. Atmospheric transformation of multispectral remote sensor data. [Great Lakes

    NASA Technical Reports Server (NTRS)

    Turner, R. E. (Principal Investigator)

    1977-01-01

    The author has identified the following significant results. The effects of earth's atmosphere were accounted for, and a simple algorithm, based upon a radiative transfer model, was developed to determine the radiance at earth's surface free of atmospheric effects. Acutal multispectral remote sensor data for Lake Erie and associated optical thickness data were used to demonstrate the effectiveness of the atmospheric transformation algorithm. The basic transformation was general in nature and could be applied to the large scale processing of multispectral aircraft or satellite remote sensor data.

  4. Spectral stratigraphy: multispectral remote sensing as a stratigraphic tool, Wind River/Big Horn basin, Wyoming

    SciTech Connect

    Lang, H.R.; Paylor, E.D.

    1987-05-01

    Stratigraphic and structural analyses of the Wind River and Big Horn basins areas of central Wyoming are in progress. One result has been the development of a new approach to stratigraphic and structural analysis that uses photogeologic and spectral interpretation of multispectral image data to remotely characterize the attitude, thickness, and lithology of strata. New multispectral systems that have only been available since 1982 are used with topographic data to map upper paleozoic and Mesozoic strata exposed on the southern margin of the Bighorn Mountains. Thematic Mapper (TM) satellite data together with topographic data are used to map lithologic contacts, measure dip and strike, and develop a stratigraphic column that is correlated with conventional surface and subsurface sections. Aircraft-acquired Airborne Imaging Spectrometer and Thermal Infrared Multispectral Scanner data add mineralogical information to the TM column, including the stratigraphic distribution of quartz, calcite, dolomite, montmorillonite, and gypsum. Results illustrate an approach that has general applicability in other geologic investigations that could benefit from remotely acquired information about areal variations in attitude, sequence, thickness, and lithology of strata exposed at the Earth's surface. Application of their methods elsewhere is limited primarily by availability of multispectral and topographic data and quality of bedrock exposures.

  5. Multispectral Remote Sensing at the Savannah River Plant

    SciTech Connect

    Shines, J.E.; Tinney, L.R.; Hawley, D.L.

    1984-01-01

    Aerial Mesurements Operations (AMO) is the remote sensing arm of the Department of Energy (DOE). The purpose of AMO is to provide timely, accurate, and cost-effective remote sensing data on a non-interference basis over DOE facilities located around the country. One of the programs administered by AMO is the Comprehensive Integrated Remote Sensing (CIRS) program, which involves the use of a wide range of data acquisition systems - aerial cameras, multispectral and infrared scanners, and nuclear detectors - to acquire data at DOE sites. The data are then processed, analyzed and interpreted to provide useful information, which is then catalogued into a data base for future use. This report describes some of the data acquisition and analysis capabilities of the Multispectral Remote Sensing Department (MRSD) as they relate to the CIRS program. 3 tables.

  6. Remote sensing techniques applied to multispectral recognition of the Aranjuez pilot zone

    NASA Technical Reports Server (NTRS)

    Lemos, G. L.; Salinas, J.; Rebollo, M.

    1977-01-01

    A rectangular (7 x 14 km) area 40 km S of Madrid was remote-sensed with a three-stage recognition process. Ground truth was established in the first phase, airborne sensing with a multispectral scanner and photographic cameras were used in the second phase, and Landsat satellite data were obtained in the third phase. Agronomic and hydrological photointerpretation problems are discussed. Color, black/white, and labeled areas are displayed for crop recognition in the land-use survey; turbidity, concentrations of pollutants and natural chemicals, and densitometry of the water are considered in the evaluation of water resources.

  7. Tasseled cap transformation for HJ multispectral remote sensing data

    NASA Astrophysics Data System (ADS)

    Han, Ling; Han, Xiaoyong

    2015-12-01

    The tasseled cap transformation of remote sensing data has been widely used in environment, agriculture, forest and ecology. Tasseled cap transformation coefficients matrix of HJ multi-spectrum data has been established through Givens rotation matrix to rotate principal component transform vector to whiteness, greenness and blueness direction of ground object basing on 24 scenes year-round HJ multispectral remote sensing data. The whiteness component enhances the brightness difference of ground object, and the greenness component preserves more detailed information of vegetation change while enhances the vegetation characteristic, and the blueness component significantly enhances factory with blue plastic house roof around the town and also can enhance brightness of water. Tasseled cap transformation coefficients matrix of HJ will enhance the application effect of HJ multispectral remote sensing data in their application fields.

  8. Implementation of Multispectral Image Classification on a Remote Adaptive Computer

    NASA Technical Reports Server (NTRS)

    Figueiredo, Marco A.; Gloster, Clay S.; Stephens, Mark; Graves, Corey A.; Nakkar, Mouna

    1999-01-01

    As the demand for higher performance computers for the processing of remote sensing science algorithms increases, the need to investigate new computing paradigms its justified. Field Programmable Gate Arrays enable the implementation of algorithms at the hardware gate level, leading to orders of m a,gnitude performance increase over microprocessor based systems. The automatic classification of spaceborne multispectral images is an example of a computation intensive application, that, can benefit from implementation on an FPGA - based custom computing machine (adaptive or reconfigurable computer). A probabilistic neural network is used here to classify pixels of of a multispectral LANDSAT-2 image. The implementation described utilizes Java client/server application programs to access the adaptive computer from a remote site. Results verify that a remote hardware version of the algorithm (implemented on an adaptive computer) is significantly faster than a local software version of the same algorithm implemented on a typical general - purpose computer).

  9. Spectra-view: A high performance, low-cost multispectral airborne imaging system

    SciTech Connect

    Helder, D.

    1996-11-01

    Although a variety of airborne platforms are available for collecting remote sensing data, a niche exists for a low cost, compact systemd capable of collecting accurate visible and infrared multispectral data in a digital format. To fill this void, an instrument known as Spectra-View was developed by Airborne Data Systems. Multispectral data is collected in the visible and near-infrared using an array of CCD cameras with appropriate spectral filtering. Infrared imaging is accomplished using commercially available cameras. Although the current system images in five spectral bands, a modular design approach allows various configurations for imaging in the visible and infrared regions with up to 10 or more channels. It was built entirely through integration of readily available commercial components, is compact enough to fly in an aircraft as small as a Cessna 172, and can record imagery at airspeeds in excess of 150 knots. A GPS-based navigation system provides a course deviation indicator for the pilot to follow and allows for georeferencing of the data. To maintain precise pointing knowledge, and at the same time keep system cost low, attitude sensors are mounted directly with the cameras rather than using a stabilized mounting system. Information is collect during camera firing of aircraft/camera attitude along the yaw, pitch, and roll axes. All data is collected in a digital format on a hard disk that is removable during flight so that virtually unlimited amounts of data may be recorded. Following collection, imagery is readily available for viewing and incorporation into computer-based systems for analysis and reduction. Ground processing software has been developed to perform radiometric calibration and georeference the imagery. Since June, 1995, the system has been collecting high-quality data in a variety of applications for numerous customers including applications in agriculture, forestry, and global change research. Several examples will be presented.

  10. Remote online processing of multispectral image data

    NASA Astrophysics Data System (ADS)

    Groh, Christine; Rothe, Hendrik

    2005-10-01

    Within the scope of this paper a both compact and economical data acquisition system for multispecral images is described. It consists of a CCD camera, a liquid crystal tunable filter in combination with an associated concept for data processing. Despite of their limited functionality (e.g.regarding calibration) in comparison with commercial systems such as AVIRIS the use of these upcoming compact multispectral camera systems can be advantageous in many applications. Additional benefit can be derived adding online data processing. In order to maintain the systems low weight and price this work proposes to separate data acquisition and processing modules, and transmit pre-processed camera data online to a stationary high performance computer for further processing. The inevitable data transmission has to be optimised because of bandwidth limitations. All mentioned considerations hold especially for applications involving mini-unmanned-aerial-vehicles (mini-UAVs). Due to their limited internal payload the use of a lightweight, compact camera system is of particular importance. This work emphasises on the optimal software interface in between pre-processed data (from the camera system), transmitted data (regarding small bandwidth) and post-processed data (based on high performance computer). Discussed parameters are pre-processing algorithms, channel bandwidth, and resulting accuracy in the classification of multispectral image data. The benchmarked pre-processing algorithms include diagnostic statistics, test of internal determination coefficients as well as loss-free and lossy data compression methods. The resulting classification precision is computed in comparison to a classification performed with the original image dataset.

  11. Multiresolution processing for fractal analysis of airborne remotely sensed data

    NASA Technical Reports Server (NTRS)

    Jaggi, S.; Quattrochi, D.; Lam, N.

    1992-01-01

    Images acquired by NASA's Calibrated Airborne Multispectral Scanner are used to compute the fractal dimension as a function of spatial resolution. Three methods are used to determine the fractal dimension: Shelberg's (1982, 1983) line-divider method, the variogram method, and the triangular prism method. A description of these methods and the result of applying these methods to a remotely-sensed image is also presented. The scanner data was acquired over western Puerto Rico in January, 1990 over land and water. The aim is to study impacts of man-induced changes on land that affect sedimentation into the near-shore environment. The data were obtained over the same area at three different pixel sizes: 10 m, 20 m, and 30 m.

  12. Multispectral thermal airborne TASI-600 data to study the Pompeii (IT) archaeological area

    NASA Astrophysics Data System (ADS)

    Palombo, Angelo; Pascucci, Simone; Pergola, Nicola; Pignatti, Stefano; Santini, Federico; Soldovieri, Francesco

    2016-04-01

    The management of archaeological areas refers to the conservation of the ruins/buildings and the eventual prospection of new areas having an archaeological potential. In this framework, airborne remote sensing is a well-developed geophysical tool for supporting the archaeological surveys of wide areas. The spectral regions applied in archaeological remote sensing spans from the VNIR to the TIR. In particular, the archaeological thermal imaging considers that materials absorb, emit, transmit, and reflect the thermal infrared radiation at different rate according to their composition, density and moisture content. Despite its potential, thermal imaging in archaeological applications are scarce. Among them, noteworthy are the ones related to the use of Landsat and ASTER [1] and airborne remote sensing [2, 3, 4 and 5]. In view of these potential in Cultural Heritage applications, the present study aims at analysing the usefulness of the high spatial resolution thermal imaging on the Pompeii archaeological park. To this purpose TASI-600 [6] airborne multispectral thermal imagery (32 channels from 8 to 11.5 nm with a spectral resolution of 100nm and a spatial resolution of 1m/pixel) was acquired on December the 7th, 2015. Airborne survey has been acquired to get useful information on the building materials (both ancient and of consolidation) characteristics and, whenever possible, to retrieve quick indicators on their conservation status. Thermal images will be, moreover, processed to have an insight of the critical environmental issues impacting the structures (e.g. moisture). The proposed study shows the preliminary results of the airborne deployments, the pre-processing of the multispectral thermal imagery and the retrieving of accurate land surface temperatures (LST). LST map will be analysed to describe the thermal pattern of the city of Pompeii and detect any thermal anomalies. As far as the ongoing TASI-600 sensors pre-processing, it will include: (a) radiometric

  13. Michigan experimental multispectral mapping system: A description of the M7 airborne sensor and its performance

    NASA Technical Reports Server (NTRS)

    Hasell, P. G., Jr.

    1974-01-01

    The development and characteristics of a multispectral band scanner for an airborne mapping system are discussed. The sensor operates in the ultraviolet, visual, and infrared frequencies. Any twelve of the bands may be selected for simultaneous, optically registered recording on a 14-track analog tape recorder. Multispectral imagery recorded on magnetic tape in the aircraft can be laboratory reproduced on film strips for visual analysis or optionally machine processed in analog and/or digital computers before display. The airborne system performance is analyzed.

  14. Analysis of multispectral signatures and investigation of multi-aspect remote sensing techniques

    NASA Technical Reports Server (NTRS)

    Malila, W. A.; Hieber, R. H.; Sarno, J. E.

    1974-01-01

    Two major aspects of remote sensing with multispectral scanners (MSS) are investigated. The first, multispectral signature analysis, includes the effects on classification performance of systematic variations found in the average signals received from various ground covers as well as the prediction of these variations with theoretical models of physical processes. The foremost effects studied are those associated with the time of day airborne MSS data are collected. Six data collection runs made over the same flight line in a period of five hours are analyzed, it is found that the time span significantly affects classification performance. Variations associated with scan angle also are studied. The second major topic of discussion is multi-aspect remote sensing, a new concept in remote sensing with scanners. Here, data are collected on multiple passes by a scanner that can be tilted to scan forward of the aircraft at different angles on different passes. The use of such spatially registered data to achieve improved classification of agricultural scenes is investigated and found promising. Also considered are the possibilities of extracting from multi-aspect data, information on the condition of corn canopies and the stand characteristics of forests.

  15. Multispectral remote sensing contribution to land surface evaporation

    NASA Technical Reports Server (NTRS)

    Choudhury, B. J.

    1990-01-01

    The global water cycle is perhaps the most important of all the biogeochemical cycles and evaporation, which is a significant component of the water cycle, is also linked with the energy and carbon cycles. Long-term evaporation over large areas has generally been computed as the difference of precipitation and river runoff. Analysis of short-term evaporation rate and its spatial pattern, however, is extremely complex, and multispectral remotely sensed data could aid in such analysis. Multispectral data considered here are visible and near-infrared reflectances, infrared surface temperature and the 37 GHz brightness temperatures. These observations are found to be not totally independent of each other. A few of their relationships are established and discussed considering physically-based models.

  16. Advanced Multispectral Scanner (AMS) study. [aircraft remote sensing

    NASA Technical Reports Server (NTRS)

    1978-01-01

    The status of aircraft multispectral scanner technology was accessed in order to develop preliminary design specifications for an advanced instrument to be used for remote sensing data collection by aircraft in the 1980 time frame. The system designed provides a no-moving parts multispectral scanning capability through the exploitation of linear array charge coupled device technology and advanced electronic signal processing techniques. Major advantages include: 10:1 V/H rate capability; 120 deg FOV at V/H = 0.25 rad/sec; 1 to 2 rad resolution; high sensitivity; large dynamic range capability; geometric fidelity; roll compensation; modularity; long life; and 24 channel data acquisition capability. The field flattening techniques of the optical design allow wide field view to be achieved at fast f/nos for both the long and short wavelength regions. The digital signal averaging technique permits maximization of signal to noise performance over the entire V/H rate range.

  17. Employing airborne multispectral digital imagery to map Brazilian pepper infestation in south Texas.

    Technology Transfer Automated Retrieval System (TEKTRAN)

    A study was conducted in south Texas to determine the feasibility of using airborne multispectral digital imagery for differentiating the invasive plant Brazilian pepper (Schinus terebinthifolius) from other cover types. Imagery obtained in the visible, near infrared, and mid infrared regions of th...

  18. Comparison of different detection methods for citrus greening disease based on airborne multispectral and hyperspectral imagery

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Citrus greening or Huanglongbing (HLB) is a devastating disease spread in many citrus groves since first found in 2005 in Florida. Multispectral (MS) and hyperspectral (HS) airborne images of citrus groves in Florida were taken to detect citrus greening infected trees in 2007 and 2010. Ground truthi...

  19. Using airborne multispectral imagery to monitor cotton root rot expansion within a growing season

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Cotton root rot is a serious and destructive disease that affects cotton production in the southwestern United States. Accurate delineation of cotton root rot infestations is important for cost-effective management of the disease. The objective of this study was to use airborne multispectral imagery...

  20. Combination of multispectral remote sensing, variable rate technology and environmental modeling for citrus pest management.

    PubMed

    Du, Qian; Chang, Ni-Bin; Yang, Chenghai; Srilakshmi, Kanth R

    2008-01-01

    The Lower Rio Grande Valley (LRGV) of south Texas is an agriculturally rich area supporting intensive production of vegetables, fruits, grain sorghum, and cotton. Modern agricultural practices involve the combined use of irrigation with the application of large amounts of agrochemicals to maximize crop yields. Intensive agricultural activities in past decades might have caused potential contamination of soil, surface water, and groundwater due to leaching of pesticides in the vadose zone. In an effort to promote precision farming in citrus production, this paper aims at developing an airborne multispectral technique for identifying tree health problems in a citrus grove that can be combined with variable rate technology (VRT) for required pesticide application and environmental modeling for assessment of pollution prevention. An unsupervised linear unmixing method was applied to classify the image for the grove and quantify the symptom severity for appropriate infection control. The PRZM-3 model was used to estimate environmental impacts that contribute to nonpoint source pollution with and without the use of multispectral remote sensing and VRT. Research findings using site-specific environmental assessment clearly indicate that combination of remote sensing and VRT may result in benefit to the environment by reducing the nonpoint source pollution by 92.15%. Overall, this study demonstrates the potential of precision farming for citrus production in the nexus of industrial ecology and agricultural sustainability. PMID:17222960

  1. Comparison of Airborne Multispectral and Hyperspectral Imagery for Yield Estimation

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Multispectral and hyperspectral imagery is being used to monitor crop conditions and map yield variability. However, limited research has been conducted to compare the differences between these two types of imagery for assessing crop growth and yield. The objective of this study was to compare airbo...

  2. Analytical models and system topologies for remote multispectral data acquisition and classification

    NASA Technical Reports Server (NTRS)

    Huck, F. O.; Park, S. K.; Burcher, E. E.; Kelly, W. L., IV

    1978-01-01

    Simple analytical models are presented of the radiometric and statistical processes that are involved in multispectral data acquisition and classification. Also presented are basic system topologies which combine remote sensing with data classification. These models and topologies offer a preliminary but systematic step towards the use of computer simulations to analyze remote multispectral data acquisition and classification systems.

  3. Remote sensing technology - The 24-channel multispectral scanner.

    NASA Technical Reports Server (NTRS)

    Hayre, H. S.; Richard, R. R.

    1973-01-01

    The multispectral scanner system installed in the NASA C-130 aircraft for use in the Earth Observations Aircraft Program constitutes a 24-channel imaging spectrometer that senses electromagnetic energy in the spectral interval from .34 to 13 microns. Energy reflected or emitted from the terrain and system calibration sources is collected by a scan mirror, reflected into collecting optics, and brought to a focus in a plane containing a 0.09 inch square aperture. A dichroic optical element splits the energy which passes through the aperture into two wavelength bands (wavelengths above and below 2 microns). These wavelength bands are then dispersed spectrally into 24 distinct spectral bands by two grating spectrometers. The spectral intervals are transformed into electrical signals by separate detector-preamplifier combinations, and the signals are used as inputs to a video processor in an airborne electronics console. System operation and performance are described.

  4. Remote sensing of soil moisture using airborne hyperspectral data

    USGS Publications Warehouse

    Finn, Michael P.; Lewis, Mark (David); Bosch, David D.; Giraldo, Mario; Yamamoto, Kristina H.; Sullivan, Dana G.; Kincaid, Russell; Luna, Ronaldo; Allam, Gopala Krishna; Kvien, Craig; Williams, Michael S.

    2011-01-01

    Landscape assessment of soil moisture is critical to understanding the hydrological cycle at the regional scale and in broad-scale studies of biophysical processes affected by global climate changes in temperature and precipitation. Traditional efforts to measure soil moisture have been principally restricted to in situ measurements, so remote sensing techniques are often employed. Hyperspectral sensors with finer spatial resolution and narrow band widths may offer an alternative to traditional multispectral analysis of soil moisture, particularly in landscapes with high spatial heterogeneity. This preliminary research evaluates the ability of remotely sensed hyperspectral data to quantify soil moisture for the Little River Experimental Watershed (LREW), Georgia. An airborne hyperspectral instrument with a short-wavelength infrared (SWIR) sensor was flown in 2005 and 2007 and the results were correlated to in situ soil moisture values. A significant statistical correlation (R 2 value above 0.7 for both sampling dates) for the hyperspectral instrument data and the soil moisture probe data at 5.08 cm (2 inches) was determined. While models for the 20.32 cm (8 inches) and 30.48 cm (12 inches) depths were tested, they were not able to estimate soil moisture to the same degree.

  5. Remote sensing of soil moisture using airborne hyperspectral data

    USGS Publications Warehouse

    Finn, M.; Lewis, M.; Bosch, D.; Giraldo, Mario; Yamamoto, K.; Sullivan, D.; Kincaid, R.; Luna, R.; Allam, G.; Kvien, Craig; Williams, M.

    2011-01-01

    Landscape assessment of soil moisture is critical to understanding the hydrological cycle at the regional scale and in broad-scale studies of biophysical processes affected by global climate changes in temperature and precipitation. Traditional efforts to measure soil moisture have been principally restricted to in situ measurements, so remote sensing techniques are often employed. Hyperspectral sensors with finer spatial resolution and narrow band widths may offer an alternative to traditional multispectral analysis of soil moisture, particularly in landscapes with high spatial heterogeneity. This preliminary research evaluates the ability of remotely sensed hyperspectral data to quantify soil moisture for the Little River Experimental Watershed (LREW), Georgia. An airborne hyperspectral instrument with a short-wavelength infrared (SWIR) sensor was flown in 2005 and 2007 and the results were correlated to in situ soil moisture values. A significant statistical correlation (R2 value above 0.7 for both sampling dates) for the hyperspectral instrument data and the soil moisture probe data at 5.08 cm (2 inches) was determined. While models for the 20.32 cm (8 inches) and 30.48 cm (12 inches) depths were tested, they were not able to estimate soil moisture to the same degree.

  6. Comparison of multispectral remote-sensing techniques for monitoring subsurface drain conditions. [Imperial Valley, California

    NASA Technical Reports Server (NTRS)

    Goettelman, R. C.; Grass, L. B.; Millard, J. P.; Nixon, P. R.

    1983-01-01

    The following multispectral remote-sensing techniques were compared to determine the most suitable method for routinely monitoring agricultural subsurface drain conditions: airborne scanning, covering the visible through thermal-infrared (IR) portions of the spectrum; color-IR photography; and natural-color photography. Color-IR photography was determined to be the best approach, from the standpoint of both cost and information content. Aerial monitoring of drain conditions for early warning of tile malfunction appears practical. With careful selection of season and rain-induced soil-moisture conditions, extensive regional surveys are possible. Certain locations, such as the Imperial Valley, Calif., are precluded from regional monitoring because of year-round crop rotations and soil stratification conditions. Here, farms with similar crops could time local coverage for bare-field and saturated-soil conditions.

  7. Upgraded airborne scanner for commercial remote sensing

    NASA Astrophysics Data System (ADS)

    Chang, Sheng-Huei; Rubin, Tod D.

    1994-06-01

    Traditional commercial remote sensing has focused on the geologic market, with primary focus on mineral identification and mapping in the visible through short-wave infrared spectral regions (0.4 to 2.4 microns). Commercial remote sensing users now demand airborne scanning capabilities spanning the entire wavelength range from ultraviolet through thermal infrared (0.3 to 12 microns). This spectral range enables detection, identification, and mapping of objects and liquids on the earth's surface and gases in the air. Applications requiring this range of wavelengths include detection and mapping of oil spills, soil and water contamination, stressed vegetation, and renewable and non-renewable natural resources, and also change detection, natural hazard mitigation, emergency response, agricultural management, and urban planning. GER has designed and built a configurable scanner that acquires high resolution images in 63 selected wave bands in this broad wavelength range.

  8. Airborne multidimensional integrated remote sensing system

    NASA Astrophysics Data System (ADS)

    Xu, Weiming; Wang, Jianyu; Shu, Rong; He, Zhiping; Ma, Yanhua

    2006-12-01

    In this paper, we present a kind of airborne multidimensional integrated remote sensing system that consists of an imaging spectrometer, a three-line scanner, a laser ranger, a position & orientation subsystem and a stabilizer PAV30. The imaging spectrometer is composed of two sets of identical push-broom high spectral imager with a field of view of 22°, which provides a field of view of 42°. The spectral range of the imaging spectrometer is from 420nm to 900nm, and its spectral resolution is 5nm. The three-line scanner is composed of two pieces of panchromatic CCD and a RGB CCD with 20° stereo angle and 10cm GSD(Ground Sample Distance) with 1000m flying height. The laser ranger can provide height data of three points every other four scanning lines of the spectral imager and those three points are calibrated to match the corresponding pixels of the spectral imager. The post-processing attitude accuracy of POS/AV 510 used as the position & orientation subsystem, which is the aerial special exterior parameters measuring product of Canadian Applanix Corporation, is 0.005° combined with base station data. The airborne multidimensional integrated remote sensing system was implemented successfully, performed the first flying experiment on April, 2005, and obtained satisfying data.

  9. River velocities from sequential multispectral remote sensing images

    NASA Astrophysics Data System (ADS)

    Chen, Wei; Mied, Richard P.

    2013-06-01

    We address the problem of extracting surface velocities from a pair of multispectral remote sensing images over rivers using a new nonlinear multiple-tracer form of the global optimal solution (GOS). The derived velocity field is a valid solution across the image domain to the nonlinear system of equations obtained by minimizing a cost function inferred from the conservation constraint equations for multiple tracers. This is done by deriving an iteration equation for the velocity, based on the multiple-tracer displaced frame difference equations, and a local approximation to the velocity field. The number of velocity equations is greater than the number of velocity components, and thus overly constrain the solution. The iterative technique uses Gauss-Newton and Levenberg-Marquardt methods and our own algorithm of the progressive relaxation of the over-constraint. We demonstrate the nonlinear multiple-tracer GOS technique with sequential multispectral Landsat and ASTER images over a portion of the Potomac River in MD/VA, and derive a dense field of accurate velocity vectors. We compare the GOS river velocities with those from over 12 years of data at four NOAA reference stations, and find good agreement. We discuss how to find the appropriate spatial and temporal resolutions to allow optimization of the technique for specific rivers.

  10. Citrus greening disease detection using airborne multispectral and hyperspectral imaging

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Hyperspectral imaging can provide unique spectral signatures for diseased vegetation. Airborne hyperspectral imaging can be used to detect potentially infected trees over a large area for rapid detection of infected zones. Ground inspection and management can be focused on these infected zones rath...

  11. Airborne Multispectral LIDAR Data for Land-Cover Classification and Land/water Mapping Using Different Spectral Indexes

    NASA Astrophysics Data System (ADS)

    Morsy, S.; Shaker, A.; El-Rabbany, A.; LaRocque, P. E.

    2016-06-01

    Airborne Light Detection And Ranging (LiDAR) data is widely used in remote sensing applications, such as topographic and landwater mapping. Recently, airborne multispectral LiDAR sensors, which acquire data at different wavelengths, are available, thus allows recording a diversity of intensity values from different land features. In this study, three normalized difference feature indexes (NDFI), for vegetation, water, and built-up area mapping, were evaluated. The NDFIs namely, NDFIG-NIR, NDFIG-MIR, and NDFINIR-MIR were calculated using data collected at three wavelengths; green: 532 nm, near-infrared (NIR): 1064 nm, and mid-infrared (MIR): 1550 nm by the world's first airborne multispectral LiDAR sensor "Optech Titan". The Jenks natural breaks optimization method was used to determine the threshold values for each NDFI, in order to cluster the 3D point data into two classes (water and land or vegetation and built-up area). Two sites at Scarborough, Ontario, Canada were tested to evaluate the performance of the NDFIs for land-water, vegetation, and built-up area mapping. The use of the three NDFIs succeeded to discriminate vegetation from built-up areas with an overall accuracy of 92.51%. Based on the classification results, it is suggested to use NDFIG-MIR and NDFINIR-MIR for vegetation and built-up areas extraction, respectively. The clustering results show that the direct use of NDFIs for land-water mapping has low performance. Therefore, the clustered classes, based on the NDFIs, are constrained by the recorded number of returns from different wavelengths, thus the overall accuracy is improved to 96.98%.

  12. Calibrated and geocoded clutter from an airborne multispectral scanner

    NASA Astrophysics Data System (ADS)

    Heuer, Markus; Bruehlmann, Ralph; John, Marc-Andre; Schmid, Konrad J.; Hueppi, Rudolph; Koenig, Reto

    1999-07-01

    Robustness of automatic target recognition (ATR) to varying observation conditions and countermeasures is substantially increased by use of multispectral sensors. Assessment of such ATR systems is performed by captive flight tests and simulations (HWIL or complete modeling). Although the clutter components of a scene can be generated with specified statistics, clutter maps directly obtained from measurement are required for validation of a simulation. In addition, urban scenes have non-stationary characteristics and are difficult to simulate. The present paper describes a scanner, data acquisition and processing system used for the generation of realistic clutter maps incorporating infrared, passive and active millimeter wave channels. The sensors are mounted on a helicopter with coincident line-of-sight, enabling us to measure consistent clutter signatures under varying observation conditions. Position and attitude data from GPS and an inertial measurement unit, respectively, are used to geometrically correct the raw scanner data. After sensor calibration the original voltage signals are converted to physical units, i.e. temperatures and reflectivities, describing the clutter independently of the scanning sensor, thus allowing us the use of the clutter maps in tests of a priori unknown multispectral sensors. The data correction procedures are described and results are presented.

  13. Determining density of maize canopy. 2: Airborne multispectral scanner data

    NASA Technical Reports Server (NTRS)

    Stoner, E. R.; Baumgardner, M. F.; Cipra, J. E.

    1971-01-01

    Multispectral scanner data were collected in two flights over a light colored soil background cover plot at an altitude of 305 m. Energy in eleven reflective wavelength band from 0.45 to 2.6 microns was recorded. Four growth stages of maize (Zea mays L.) gave a wide range of canopy densities for each flight date. Leaf area index measurements were taken from the twelve subplots and were used as a measure of canopy density. Ratio techniques were used to relate uncalibrated scanner response to leaf area index. The ratios of scanner data values for the 0.72 to 0.92 micron wavelength band over the 0.61 to 0.70 micron wavelength band were calculated for each plot. The ratios related very well to leaf area index for a given flight date. The results indicated that spectral data from maize canopies could be of value in determining canopy density.

  14. Biooptical variability in the Greenland Sea observed with the Multispectral Airborne Radiometer System (MARS)

    NASA Technical Reports Server (NTRS)

    Mueller, James L.; Trees, Charles C.

    1989-01-01

    A site-specific ocean color remote sensing algorithm was developed and used to convert Multispectral Airborne Radiometer System (MARS) spectral radiance measurements to chlorophyll-a concentration profiles along aircraft tracklines in the Greenland Sea. The analysis is described and the results given in graphical or tabular form. Section 2 describes the salient characteristics and history of development of the MARS instrument. Section 3 describes the analyses of MARS flight segments over consolidated sea ice, resulting in a set of altitude dependent ratios used (over water) to estimate radiance reflected by the surface and atmosphere from total radiance measured. Section 4 presents optically weighted pigment concentrations calculated from profile data, and spectral reflectances measured in situ from the top meter of the water column; this data was analyzed to develop an algorithm relating chlorophyll-a concentrations to the ratio of radiance reflectances at 441 and 550 nm (with a selection of coefficients dependent upon whether significant gelvin presence is implied by a low ratio of reflectances at 410 and 550 nm). Section 5 describes the scaling adjustments which were derived to reconcile the MARS upwelled radiance ratios at 410:550 nm and 441:550 nm to in situ reflectance ratios measured simultaneously on the surface. Section 6 graphically presents the locations of MARS data tracklines and positions of the surface monitoring R/V. Section 7 presents stick-plots of MARS tracklines selected to illustrate two-dimensional spatial variability within the box covered by each day's flight. Section 8 presents curves of chlorophyll-a concentration profiles derived from MARS data along survey tracklines. Significant results are summarized in Section 1.

  15. A real-time multispectral imaging system for low- or mid-altitude remote sensing

    NASA Astrophysics Data System (ADS)

    Yi, Dingrong; Kong, Linghua

    2012-10-01

    Multispectral imaging is a powerful tool in remote sensing applications. Recently a micro-arrayed narrow-band optical mosaic filter was invented and successfully fabricated to reduce the size and cost of multispectral imaging devices in order to meet the requirements for low- or mid- altitude remote sensing. Such a filter with four narrow bands is integrated with an off-shelf CCD camera, resulting in an economic and light-weight multispectral imaging camera with the capacity of producing multiple images at different center wavelengths with a single shot. The multispectral imaging camera is then integrated with a wireless transmitter and battery to produce a remote sensing multispectral imaging system. The design and some preliminary results of a prototyped multispectral imaging system with the potential for remote sensing applications with a weight of only 200 grams are reported. The prototyped multispectral imaging system eliminates the image registration procedure required by traditional multispectral imaging technologies. In addition, it has other advantages such as low cost, being light weight and compact in design.

  16. GIS Meets Airborne MSS: Geospatial Applications of High-Resolution Multispectral Data

    SciTech Connect

    Albert Guber

    1999-07-27

    Bechtel Nevada operates and flies Daedalus multispectral scanners for funded project tasks at the Department of Energy's Remote Sensing Laboratory. Historically, processing and analysis of multispectral data has afforded scientists the opportunity to see natural phenomena not visible to the naked eye. However, only recently has a system, more specifically a Geometric Correction System, existed to automatically geo-reference these data directly into a Geographic Information (GIS) database. Now, analyses, performed previously in a nongeospatial environment, are integrated directly into an Arc/Info GIS. This technology is of direct benefit to environmental and emergency response applications.

  17. Differentiating aquatic plant communities in a eutrophic river using hyperspectral and multispectral remote sensing

    USGS Publications Warehouse

    Tian, Y.Q.; Yu, Q.; Zimmerman, M.J.; Flint, S.; Waldron, M.C.

    2010-01-01

    This study evaluates the efficacy of remote sensing technology to monitor species composition, areal extent and density of aquatic plants (macrophytes and filamentous algae) in impoundments where their presence may violate water-quality standards. Multispectral satellite (IKONOS) images and more than 500 in situ hyperspectral samples were acquired to map aquatic plant distributions. By analyzing field measurements, we created a library of hyperspectral signatures for a variety of aquatic plant species, associations and densities. We also used three vegetation indices. Normalized Difference Vegetation Index (NDVI), near-infrared (NIR)-Green Angle Index (NGAI) and normalized water absorption depth (DH), at wavelengths 554, 680, 820 and 977 nm to differentiate among aquatic plant species composition, areal density and thickness in cases where hyperspectral analysis yielded potentially ambiguous interpretations. We compared the NDVI derived from IKONOS imagery with the in situ, hyperspectral-derived NDVI. The IKONOS-based images were also compared to data obtained through routine visual observations. Our results confirmed that aquatic species composition alters spectral signatures and affects the accuracy of remote sensing of aquatic plant density. The results also demonstrated that the NGAI has apparent advantages in estimating density over the NDVI and the DH. In the feature space of the three indices, 3D scatter plot analysis revealed that hyperspectral data can differentiate several aquatic plant associations. High-resolution multispectral imagery provided useful information to distinguish among biophysical aquatic plant characteristics. Classification analysis indicated that using satellite imagery to assess Lemna coverage yielded an overall agreement of 79% with visual observations and >90% agreement for the densest aquatic plant coverages. Interpretation of biophysical parameters derived from high-resolution satellite or airborne imagery should prove to be a

  18. Mapping crop ground cover using airborne multispectral digital imagery

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Empirical relationships between remotely sensed vegetation indices and density information, such as leaf area index or ground cover (GC), are commonly used to derive spatial information in many precision farming operations. In this study, we modified an existing methodology that does not depend on e...

  19. EVALUATION OF COTTON DEFOLIATION STRATEGIES USING AIRBORNE MULTISPECTRAL IMAGERY

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Visual observations and ground measurements are commonly used to evaluate cotton (Gossypium hirsutum L.) harvest aids for defoliation, boll opening, and re-growth control. This paper presents a remote sensing-based method for evaluating the effectiveness of different defoliation treatments. Field ...

  20. Multispectral, hyperspectral, and LiDAR remote sensing and geographic information fusion for improved earthquake response

    NASA Astrophysics Data System (ADS)

    Kruse, F. A.; Kim, A. M.; Runyon, S. C.; Carlisle, Sarah C.; Clasen, C. C.; Esterline, C. H.; Jalobeanu, A.; Metcalf, J. P.; Basgall, P. L.; Trask, D. M.; Olsen, R. C.

    2014-06-01

    The Naval Postgraduate School (NPS) Remote Sensing Center (RSC) and research partners have completed a remote sensing pilot project in support of California post-earthquake-event emergency response. The project goals were to dovetail emergency management requirements with remote sensing capabilities to develop prototype map products for improved earthquake response. NPS coordinated with emergency management services and first responders to compile information about essential elements of information (EEI) requirements. A wide variety of remote sensing datasets including multispectral imagery (MSI), hyperspectral imagery (HSI), and LiDAR were assembled by NPS for the purpose of building imagery baseline data; and to demonstrate the use of remote sensing to derive ground surface information for use in planning, conducting, and monitoring post-earthquake emergency response. Worldview-2 data were converted to reflectance, orthorectified, and mosaicked for most of Monterey County; CA. Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) data acquired at two spatial resolutions were atmospherically corrected and analyzed in conjunction with the MSI data. LiDAR data at point densities from 1.4 pts/m2 to over 40 points/ m2 were analyzed to determine digital surface models. The multimodal data were then used to develop change detection approaches and products and other supporting information. Analysis results from these data along with other geographic information were used to identify and generate multi-tiered products tied to the level of post-event communications infrastructure (internet access + cell, cell only, no internet/cell). Technology transfer of these capabilities to local and state emergency response organizations gives emergency responders new tools in support of post-disaster operational scenarios.

  1. Towards Automatic Single-Sensor Mapping by Multispectral Airborne Laser Scanning

    NASA Astrophysics Data System (ADS)

    Ahokas, E.; Hyyppä, J.; Yu, X.; Liang, X.; Matikainen, L.; Karila, K.; Litkey, P.; Kukko, A.; Jaakkola, A.; Kaartinen, H.; Holopainen, M.; Vastaranta, M.

    2016-06-01

    This paper describes the possibilities of the Optech Titan multispectral airborne laser scanner in the fields of mapping and forestry. Investigation was targeted to six land cover classes. Multispectral laser scanner data can be used to distinguish land cover classes of the ground surface, including the roads and separate road surface classes. For forest inventory using point cloud metrics and intensity features combined, total accuracy of 93.5% was achieved for classification of three main boreal tree species (pine, spruce and birch).When using intensity features - without point height metrics - a classification accuracy of 91% was achieved for these three tree species. It was also shown that deciduous trees can be further classified into more species. We propose that intensity-related features and waveform-type features are combined with point height metrics for forest attribute derivation in area-based prediction, which is an operatively applied forest inventory process in Scandinavia. It is expected that multispectral airborne laser scanning can provide highly valuable data for city and forest mapping and is a highly relevant data asset for national and local mapping agencies in the near future.

  2. Land use classification utilizing remote multispectral scanner data and computer analysis techniques

    NASA Technical Reports Server (NTRS)

    Leblanc, P. N.; Johannsen, C. J.; Yanner, J. E.

    1973-01-01

    An airborne multispectral scanner was used to collect the visible and reflective infrared data. A small subdivision near Lafayette, Indiana was selected as the test site for the urban land use study. Multispectral scanner data were collected over the subdivision on May 1, 1970 from an altitude of 915 meters. The data were collected in twelve wavelength bands from 0.40 to 1.00 micrometers by the scanner. The results indicated that computer analysis of multispectral data can be very accurate in classifying and estimating the natural and man-made materials that characterize land uses in an urban scene.

  3. Multispectral light scattering imaging and multivariate analysis of airborne particulates

    NASA Astrophysics Data System (ADS)

    Holler, Stephen; Skelsey, Charles R.; Fuerstenau, Stephen D.

    2005-05-01

    Light scattering patterns from non-spherical particles and aggregates exhibit complex structure that is only revealed when observing in two angular dimensions. However, due to the varied shape and packing of such aerosols, the rich structure in the two-dimensional angular optical scattering (TAOS) pattern varies from particle to particle. We examine two-dimensional light scattering patterns obtained at multiple wavelengths using a single CCD camera with minimal cross talk between channels. The integration of the approach with a single CCD camera assures that data is acquired within the same solid angle and orientation. Since the optical size of the scattering particle is inversely proportional to the illuminating wavelength, the spectrally resolved scattering information provides characteristic information about the airborne particles simultaneously in two different scaling regimes. The simultaneous acquisition of data from airborne particulate matter at two different wavelengths allows for additional degrees of freedom in the analysis and characterization of the aerosols. Whereas our previous multivariate analyses of aerosol particles has relied solely on spatial frequency components, our present approach attempts to incorporate the relative symmetry of the particledetector system while extracting information content from both spectral channels. In addition to single channel data, this current approach also examines relative metrics. Consequently, we have begun to employ multivariate techniques based on novel morphological descriptors in order to classify "unknown" particles within a database of TAOS patterns from known aerosols utilizing both spectral and spatial information acquired. A comparison is made among several different classification metrics, all of which show improved classification capabilities relative to our previous approaches.

  4. Effectiveness of airborne multispectral thermal data for karst groundwater resources recognition in coastal areas

    NASA Astrophysics Data System (ADS)

    Pignatti, Stefano; Fusilli, Lorenzo; Palombo, Angelo; Santini, Federico; Pascucci, Simone

    2013-04-01

    Currently the detection, use and management of groundwater in karst regions can be considered one of the most significant procedures for solving water scarcity problems during periods of low rainfall this because groundwater resources from karst aquifers play a key role in the water supply in karst areas worldwide [1]. In many countries of the Mediterranean area, where karst is widespread, groundwater resources are still underexploited, while surface waters are generally preferred [2]. Furthermore, carbonate aquifers constitute a crucial thermal water resource outside of volcanic areas, even if there is no detailed and reliable global assessment of thermal water resources. The composite hydrogeological characteristics of karst, particularly directions and zones of groundwater distribution, are not up till now adequately explained [3]. In view of the abovementioned reasons the present study aims at analyzing the detection capability of high spatial resolution thermal remote sensing of karst water resources in coastal areas in order to get useful information on the karst springs flow and on different characteristics of these environments. To this purpose MIVIS [4, 5] and TASI-600 [6] airborne multispectral thermal imagery (see sensors' characteristics in Table 1) acquired on two coastal areas of the Mediterranean area interested by karst activity, one located in Montenegro and one in Italy, were used. One study area is located in the Kotor Bay, a winding bay on the Adriatic Sea surrounded by high mountains in south-western Montenegro and characterized by many subaerial and submarine coastal springs related to deep karstic channels. The other study area is located in Santa Cesarea (Italy), encompassing coastal cold springs, the main local source of high quality water, and also a noticeable thermal groundwater outflow. The proposed study shows the preliminary results of the two airborne deployments on these areas. The preprocessing of the multispectral thermal imagery

  5. Urban land use monitoring from computer-implemented processing of airborne multispectral data

    NASA Technical Reports Server (NTRS)

    Todd, W. J.; Mausel, P. W.; Baumgardner, M. F.

    1976-01-01

    Machine processing techniques were applied to multispectral data obtained from airborne scanners at an elevation of 600 meters over central Indianapolis in August, 1972. Computer analysis of these spectral data indicate that roads (two types), roof tops (three types), dense grass (two types), sparse grass (two types), trees, bare soil, and water (two types) can be accurately identified. Using computers, it is possible to determine land uses from analysis of type, size, shape, and spatial associations of earth surface images identified from multispectral data. Land use data developed through machine processing techniques can be programmed to monitor land use changes, simulate land use conditions, and provide impact statistics that are required to analyze stresses placed on spatial systems.

  6. Non-linear methods in remotely sensed multispectral data classification

    NASA Astrophysics Data System (ADS)

    Nikolov, Hs; Petkov, Di; Jeliazkova, N.; Ruseva, S.; Boyanov, K.

    The aim of this research is to examine existing geoinformation processing systems and to develop a new system, able to cope with the stochastic nature of remote sensing data. In order to achieve this objective, it is necessary to structure the methodological knowledge in the area of data mining and reveal the most suitable methods for the prediction and decision support based on large amounts of multispectral data. Non-linear methods are a vast and quickly advancing field of research, but in the case of geoinformatics they are far away from applications targeted to end-users. The idea is to establish a framework by decomposing the task into functionality objectives and to allow the end-user to experiment with a set of classification methods and select the best methods for specific applications. In this framework we consider Bayesian analysis tools, nonlinear regression models, neural networks, fuzzy reasoning systems, kernel methods, evolutionary programming, genetic algorithms and decision trees. In particular we compare our results from Bayesian classification based on estimated probability densities of the data to the results obtained from other classification methods. We demonstrate that the theoretically optimal Bayesian classification also provides optimal classification in practice.

  7. Bandpass filter arrays patterned by photolithography for multispectral remote sensing

    NASA Astrophysics Data System (ADS)

    Bauer, T.; Thome, Heidi; Eisenhammer, Thomas

    2014-10-01

    Optical remote sensing of the earth from air and space typically utilizes several channels from visible (VIS), near infrared (NIR) up to the short wave infrared (SWIR) spectral region. Thin-film optical filters are applied to select these channels. Filter wheels and arrays of discrete stripe filters are standard configurations. To achieve compact and light weight camera designs multi-channel filter plates or assemblies can be mounted close to the electronic detectors. Optics Balzers has implemented a micro-structuring process based on a sequence of multiple coatings and photolithography on the same substrate. High-performance band pass filters are applied by plasma assisted evaporation (plasma IAD) with advance plasma source (APS) technology and optical broad-band monitoring (BBM). This technology has already proven for various multi spectral imager (MSI) configurations on fused silica, sapphire and other substrates for remote sensing application. The optical filter design and performance is limited by the maximum coating thickness micro-structurable by photolithographic lift-off processes and by thermal and radiation load on the photoresist mask during the process Recent progress in image resolution and sensor selectivity requires improvements of optical filter performance. Blocking in the UV and NIR and in between the spectral cannels, in-band transmission and filter edge steepness are subject of current development. Technological limits of the IAD coating accuracy can be overcome by more precise coating technologies like plasma assisted reactive magnetron sputtering (PARMS) and combination with optical broadband monitoring (BBM). We present an overview about concepts and technologies for band-pass filter arrays for multi-spectral imaging at Optics Balzers. Recent performance improvements of filter arrays made by micro-structuring will be presented.

  8. Airborne remote sensing to detect greenbug stress to wheat

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Vegetation indices calculated from the quantity of reflected electromagnetic radiation have been used to quantify levels of stress to plants. Greenbugs cause stress to wheat plants and therefore multi-spectral remote sensing may be useful for detecting greenbug infested wheat fields. The objective...

  9. The Need for High Spatial Resolution Multispectral Thermal Remote Sensing Data In Urban Heat Island Research

    NASA Technical Reports Server (NTRS)

    Quattrochi, Dale A.; Luvall, Jeffrey C.

    2006-01-01

    Although the study of the Urban Heat Island (UHI) effect dates back to the early 1800's when Luke Howard discovered London s heat island, it has only been with the advent of thermal remote sensing systems that the extent, characteristics, and impacts of the UHI have become to be understood. Analysis of the UHI effect is important because above all, this phenomenon can directly influence the health and welfare of urban residents. For example, in 1995, over 700 people died in Chicago due to heat-related causes. UHI s are characterized by increased temperature in comparison to rural areas and mortality rates during a heat wave increase exponentially with the maximum temperature, an effect that is exacerbated by the UHI. Aside from the direct impacts of the UHI on temperature, UHI s can produce secondary effects on local meteorology, including altering local wind patterns, increased development of clouds and fog, and increasing rates of precipitation either over, or downwind, of cities. Because of the extreme heterogeneity of the urban surface, in combination with the sprawl associated with urban growth, thermal infrared (TIR) remote sensing data have become of significant importance in understanding how land cover and land use characteristics affect the development and intensification of the UHI. TIR satellite data have been used extensively to analyze the surface temperature regimes of cities to help observe and measure the impacts of surface temperatures across the urban landscape. However, the spatial scales at which satellite TIR data are collected are for the most part, coarse, with the finest readily available TIR data collected by the Landsat ETM+ sensor at 60m spatial resolution. For many years, we have collected high spatial resolution (10m) data using an airborne multispectral TIR sensor over a number of cities across the United States. These high resolution data have been used to develop an understanding of how discrete surfaces across the urban environment

  10. The Need for High Spatial Resolution Multispectral Thermal Remote Sensing Data In Urban Heat Island Research

    NASA Astrophysics Data System (ADS)

    Quattrochi, D. A.; Luvall, J. C.

    2006-12-01

    Although the study of the Urban Heat Island (UHI) effect dates back to the early 1800's when Luke Howard discovered London's heat island, it has only been with the advent of thermal remote sensing systems that the extent, characteristics, and impacts of the UHI have become to be understood. Analysis of the UHI effect is important because above all, this phenomenon can directly influence the health and welfare of urban residents. For example, in 1995, over 700 people died in Chicago due to heat-related causes. UHI's are characterized by increased temperature in comparison to rural areas and mortality rates during a heat wave increase exponentially with the maximum temperature, an effect that is exacerbated by the UHI. Aside from the direct impacts of the UHI on temperature, UHI's can produce secondary effects on local meteorology, including altering local wind patterns, increased development of clouds and fog, and increasing rates of precipitation either over, or downwind, of cities. Because of the extreme heterogeneity of the urban surface, in combination with the sprawl associated with urban growth, thermal infrared (TIR) remote sensing data have become of significant importance in understanding how land cover and land use characteristics affect the development and intensification of the UHI. TIR satellite data have been used extensively to analyze the surface temperature regimes of cities to help observe and measure the impacts of surface temperatures across the urban landscape. However, the spatial scales at which satellite TIR data are collected are for the most part, coarse, with the finest readily available TIR data collected by the Landsat ETM+ sensor at 60m spatial resolution. For many years, we have collected high spatial resolution (10m) data using an airborne multispectral TIR sensor over a number of cities across the United States. These high resolution data have been used to develop an understanding of how discrete surfaces across the urban environment

  11. Two mirror objective design for multispectral remote sensing

    NASA Technical Reports Server (NTRS)

    Clark, P. P.

    1982-01-01

    A two mirror flat field anastigmatic telescope was designed for multispectral sensing. The design was adapted to prism-type beamsplitting arrangements without loss of multispectral image quality by the addition of one refractive element. In addition to being relatively simple and mechanically insensitive, the design is immune to focus shift caused by index of refraction variation with temperature.

  12. The design and the development of a hyperspectral and multispectral airborne mapping system

    NASA Astrophysics Data System (ADS)

    Gorsevski, Pece V.; Gessler, Paul E.

    Flexible and cost-effective tools for rapid image acquisition and natural resource mapping are needed by land managers. This paper describes the hardware and software architecture of a low-cost system that can be deployed on a light aircraft for rapid data acquisition. The Hyperspectral and Multispectral Cameras for Airborne Mapping (HAMCAM) was designed and developed in the Geospatial Laboratory for Environmental Dynamics at the University of Idaho as a student-learning tool, and to enhance the existing curriculum currently offered. The system integrates a hyperspectral sensor with four multispectral cameras, an Inertial Navigation System (INS), a Wide Area Augmentation System (WAAS)-capable Global Positioning System (GPS), a data acquisition computer, and custom software for running the sensors in a variety of different modes. The outputs include very high resolution imagery obtained in four adjustable visible and near-infrared bands from the multispectral imager. The hyperspectral sensor acquires 240 spectral bands along 2.7 nm intervals within the 445-900 nm range. The INS provides aircraft pitch, roll and yaw information for rapid geo-registration of the imagery. This paper will discuss the challenges associated with the development of the system and the integration of components and software for implementation of this system for natural resource management applications. In addition, sample imagery acquired by the sensor will be presented.

  13. Multispectral remote sensing from unmanned aircraft: image processing workflows and applications for rangeland environments

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Using unmanned aircraft systems (UAS) as remote sensing platforms offers the unique ability for repeated deployment for acquisition of high temporal resolution data at very high spatial resolution. Most image acquisitions from UAS have been in the visible bands, while multispectral remote sensing ap...

  14. Testing of Land Cover Classification from Multispectral Airborne Laser Scanning Data

    NASA Astrophysics Data System (ADS)

    Bakuła, K.; Kupidura, P.; Jełowicki, Ł.

    2016-06-01

    Multispectral Airborne Laser Scanning provides a new opportunity for airborne data collection. It provides high-density topographic surveying and is also a useful tool for land cover mapping. Use of a minimum of three intensity images from a multiwavelength laser scanner and 3D information included in the digital surface model has the potential for land cover/use classification and a discussion about the application of this type of data in land cover/use mapping has recently begun. In the test study, three laser reflectance intensity images (orthogonalized point cloud) acquired in green, near-infrared and short-wave infrared bands, together with a digital surface model, were used in land cover/use classification where six classes were distinguished: water, sand and gravel, concrete and asphalt, low vegetation, trees and buildings. In the tested methods, different approaches for classification were applied: spectral (based only on laser reflectance intensity images), spectral with elevation data as additional input data, and spectro-textural, using morphological granulometry as a method of texture analysis of both types of data: spectral images and the digital surface model. The method of generating the intensity raster was also tested in the experiment. Reference data were created based on visual interpretation of ALS data and traditional optical aerial and satellite images. The results have shown that multispectral ALS data are unlike typical multispectral optical images, and they have a major potential for land cover/use classification. An overall accuracy of classification over 90% was achieved. The fusion of multi-wavelength laser intensity images and elevation data, with the additional use of textural information derived from granulometric analysis of images, helped to improve the accuracy of classification significantly. The method of interpolation for the intensity raster was not very helpful, and using intensity rasters with both first and last return

  15. Airborne remote sensing of forest biomes

    NASA Technical Reports Server (NTRS)

    Sader, Steven A.

    1987-01-01

    Airborne sensor data of forest biomes obtained using an SAR, a laser profiler, an IR MSS, and a TM simulator are presented and examined. The SAR was utilized to investigate forest canopy structures in Mississippi and Costa Rica; the IR MSS measured forest canopy temperatures in Oregon and Puerto Rico; the TM simulator was employed in a tropical forest in Puerto Rico; and the laser profiler studied forest canopy characteristics in Costa Rica. The advantages and disadvantages of airborne systems are discussed. It is noted that the airborne sensors provide measurements applicable to forest monitoring programs.

  16. A Multispectral Image Creating Method for a New Airborne Four-Camera System with Different Bandpass Filters

    PubMed Central

    Li, Hanlun; Zhang, Aiwu; Hu, Shaoxing

    2015-01-01

    This paper describes an airborne high resolution four-camera multispectral system which mainly consists of four identical monochrome cameras equipped with four interchangeable bandpass filters. For this multispectral system, an automatic multispectral data composing method was proposed. The homography registration model was chosen, and the scale-invariant feature transform (SIFT) and random sample consensus (RANSAC) were used to generate matching points. For the difficult registration problem between visible band images and near-infrared band images in cases lacking manmade objects, we presented an effective method based on the structural characteristics of the system. Experiments show that our method can acquire high quality multispectral images and the band-to-band alignment error of the composed multiple spectral images is less than 2.5 pixels. PMID:26205264

  17. Airborne Remote Sensing for Earth Science Applications

    NASA Technical Reports Server (NTRS)

    Aubrey, Andrew

    2013-01-01

    Topics covered include: Passive Remote Sensing Methods, Imaging Spectroscopy Approach, Remote Measurement via Spectral Fitting, Imaging Spectroscopy Mapping Wetland Dominants 2010 LA (AVIRIS), Deepwater Horizon Response I, Deepwater Horizon Response II, AVIRIS Ocean Color Studies.

  18. Effectiveness of airborne multispectral thermal data for karst groundwater resources recognition in coastal areas

    NASA Astrophysics Data System (ADS)

    Pignatti, Stefano; Fusilli, Lorenzo; Palombo, Angelo; Santini, Federico; Pascucci, Simone

    2013-04-01

    Currently the detection, use and management of groundwater in karst regions can be considered one of the most significant procedures for solving water scarcity problems during periods of low rainfall this because groundwater resources from karst aquifers play a key role in the water supply in karst areas worldwide [1]. In many countries of the Mediterranean area, where karst is widespread, groundwater resources are still underexploited, while surface waters are generally preferred [2]. Furthermore, carbonate aquifers constitute a crucial thermal water resource outside of volcanic areas, even if there is no detailed and reliable global assessment of thermal water resources. The composite hydrogeological characteristics of karst, particularly directions and zones of groundwater distribution, are not up till now adequately explained [3]. In view of the abovementioned reasons the present study aims at analyzing the detection capability of high spatial resolution thermal remote sensing of karst water resources in coastal areas in order to get useful information on the karst springs flow and on different characteristics of these environments. To this purpose MIVIS [4, 5] and TASI-600 [6] airborne multispectral thermal imagery (see sensors' characteristics in Table 1) acquired on two coastal areas of the Mediterranean area interested by karst activity, one located in Montenegro and one in Italy, were used. One study area is located in the Kotor Bay, a winding bay on the Adriatic Sea surrounded by high mountains in south-western Montenegro and characterized by many subaerial and submarine coastal springs related to deep karstic channels. The other study area is located in Santa Cesarea (Italy), encompassing coastal cold springs, the main local source of high quality water, and also a noticeable thermal groundwater outflow. The proposed study shows the preliminary results of the two airborne deployments on these areas. The preprocessing of the multispectral thermal imagery

  19. Fusion of remotely sensed data from airborne and ground-based sensors for cotton regrowth study

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The study investigated the use of aerial multispectral imagery and ground-based hyperspectral data for the discrimination of different crop types and timely detection of cotton plants over large areas. Airborne multispectral imagery and ground-based spectral reflectance data were acquired at the sa...

  20. Active/passive scanning. [airborne multispectral laser scanners for agricultural and water resources applications

    NASA Technical Reports Server (NTRS)

    Woodfill, J. R.; Thomson, F. J.

    1979-01-01

    The paper deals with the design, construction, and applications of an active/passive multispectral scanner combining lasers with conventional passive remote sensors. An application investigation was first undertaken to identify remote sensing applications where active/passive scanners (APS) would provide improvement over current means. Calibration techniques and instrument sensitivity are evaluated to provide predictions of the APS's capability to meet user needs. A preliminary instrument design was developed from the initial conceptual scheme. A design review settled the issues of worthwhile applications, calibration approach, hardware design, and laser complement. Next, a detailed mechanical design was drafted and construction of the APS commenced. The completed APS was tested and calibrated in the laboratory, then installed in a C-47 aircraft and ground tested. Several flight tests completed the test program.

  1. Applications of airborne remote sensing in atmospheric sciences research

    NASA Technical Reports Server (NTRS)

    Serafin, R. J.; Szejwach, G.; Phillips, B. B.

    1984-01-01

    This paper explores the potential for airborne remote sensing for atmospheric sciences research. Passive and active techniques from the microwave to visible bands are discussed. It is concluded that technology has progressed sufficiently in several areas that the time is right to develop and operate new remote sensing instruments for use by the community of atmospheric scientists as general purpose tools. Promising candidates include Doppler radar and lidar, infrared short range radiometry, and microwave radiometry.

  2. MULTISPECTRAL TECHNIQUES FOR REMOTE MONITORING OF SEDIMENT IN WATER: A FEASIBILITY INVESTIGATION

    EPA Science Inventory

    A data acquisition and analysis program has been undertaken to demonstrate the feasibility of remote multispectral techniques for monitoring suspended sediment concentrations in natural water bodies. Two hundred surface albedo measurements (400 to 1,000 nanometers) were made at L...

  3. Remote Sensing Crop Leaf Area Index Using Unmanned Airborne Vehicles

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Remote sensing with unmanned airborne vehicles (UAVs) has more potential for within-season crop management than conventional satellite imagery because: (1) pixels have very high resolution, (2) cloud cover would not prevent acquisition during critical periods of growth, and (3) quick delivery of inf...

  4. Characterizing thermal features from multi-spectral remote sensing data using dynamic calibration procedures

    NASA Astrophysics Data System (ADS)

    Hardy, Colin C.

    A thermal infrared remote sensing project was implemented to develop methods for identifying, classifying, and mapping thermal features. This study is directed at geothermal features, with the expectation that new protocols developed here will apply to the wildland fire thermal environment. Airborne multi-spectral digital imagery was acquired over the geothermally active Norris Basin region of Yellowstone National Park, USA. Two image acquisitions were flown, with one near solar noon and the other at night. The five-band image data included thermal infrared (TIR), near-infrared (NIR), and three visible bandpasses. While focused on TIR, the study relied on the multi-spectral visible and NIR data as well as on an ancillary hyperspectral data set. The raw, five-band data were uncalibrated, requiring implementation of two calibration protocols. First, a vicarious calibration procedure was developed to compute reflectance for the visible and NIR bands using an independently calibrated hyperspectral dataset. Second, a dynamic, in-scene calibration procedure was developed for the thermal sensor that exploited natural, pseudo-invariant thermal reference targets instrumented with kinetic temperature recorders. A suite of thermal attributes was derived, including daytime and nighttime radiant temperatures, a temperature difference (DeltaT), albedo, one minus albedo, and apparent thermal inertia (ATI). The albedo terms were computed using a published weighed-average albedo algorithm based on ratios of the narrowband red and NIR reflectances to total solar irradiance for the respective red and NIR bandpasses. In the absence of verifiable "truth," a step-wise chain of unsupervised classification and multivariate analysis exercises was performed, drawing heavily on "fuzzy truth." A final classification synthesizes a "thermal phenomenology" comprised of four components: spectral, statistical, geographical/contextual, and feature space. In situ measurements paired with image data

  5. Land surface temperature retrieved from airborne multispectral scanner mid-infrared and thermal-infrared data.

    PubMed

    Qian, Yong-Gang; Wang, Ning; Ma, Ling-Ling; Liu, Yao-Kai; Wu, Hua; Tang, Bo-Hui; Tang, Ling-Li; Li, Chuan-Rong

    2016-01-25

    Land surface temperature (LST) is one of the key parameters in the physics of land surface processes at local/global scales. In this paper, a LST retrieval method was proposed from airborne multispectral scanner data comparing one mid-infrared (MIR) channel and one thermal infrared (TIR) channel with the land surface emissivity given as a priori knowledge. To remove the influence of the direct solar radiance efficiently, a relationship between the direct solar radiance and water vapor content and the view zenith angle and solar zenith angle was established. Then, LST could be retrieved with a split-window algorithm from MIR/TIR data. Finally, the proposed algorithm was applied to the actual airborne flight data and validated with in situ measurements of land surface types in the Baotou site in China on 17 October 2014. The results demonstrate that the difference between the retrieved and in situ LST was less than 1.5 K. The bais, RMSE, and standard deviation of the retrieved LST were 0.156 K, 0.883 K, and 0.869 K, respectively, for samples. PMID:26832579

  6. Remote sensing using an airborne biosensor

    SciTech Connect

    Ligler, F.S.; Anderson, G.P.; Davidson, P.T.; Stenger, D.A.; Ives, J.T.; King, K.D.; Page, G.; Whelan, J.P.

    1998-08-15

    There is no current method for remote identification of aerosolized bacteria. In particular, such a capability is required to warn of a biological warfare attack prior to human exposure. A fiber optic biosensor, capable of running four simultaneous immunoassays, was integrated with an automated fluidics unit, a cyclone-type air sampler, a radio transceiver, and batteries on a small, remotely piloted airplane capable of carrying a 4.5-kg payload. The biosensor system was able to collect aerosolized bacteria in flight, identify them, and transmit the data to the operator on the ground. The results demonstrate the feasibility of integrating a biosensor into a portable, remotely operated system for environmental analysis.

  7. The Geologic Remote Sensing Field Experiment (GRSFE): The first geology multisensor airborne campaign

    NASA Technical Reports Server (NTRS)

    Evans, Diane L.; Arvidson, Raymond E.

    1991-01-01

    The primary objective of the Geologic Remote Sensing Field Experiment (GRSFE) is to acquire relevant data for geological sites that can be used to test models for extraction of surface property information from remote sensing data for earth, Mars and Venus in support of the Earth Observing System (EOS), Mars Observer, and Magellan, respectively. Over forty scientists from eight universities and three NASA centers are participating in GRSFE which is co-sponsored by the NASA Planetary Geology and Geophysics Program and the NASA Geology Program. Highlights of the airborne campaign included the first simultaneous acquisition of Airborne Visible and Infrared Imaging Spectrometer (AVRIS) and Thermal Infrared Multispectral Scanner (TIMS) data on September 29, 1989, and acquisition of Advanced Solid-State Array Spectroradiometer (ASAS), Polarimetric Synthetic Aperture Radar (AIRSAR), and Airborne Terrain Laser Altimeter System (ATLAS) data all within three months of each other. The sites covered were Lunar Crater Volcanic Field and Fish Lake Valley in Nevada; and Cima Volcanic Field, Death Valley, and Ubehebe Crater in California. Coincident field measurements included meteorological and atmospheric measurements, visible/near-infrared and thermal spectra, and characterization of geology and vegetation cover. The GRSFE airborne and field data will be reduced to a suite of standard products and submitted, along with appropriate documentation, to the Planetary Data System (PDS) and the Pilot Land Data System (PLDS). These data will be used for a variety of investigations including paleoclimatic studies in the arid southwestern United States, and analysis of Magellan data. GRSFE data will also be used to support Mars Observer Laser Altimeter (MOLA) and Mars Rover Sample Return (MRSR) simulation studies.

  8. Experiment of monitoring thermal discharge drained from nuclear plant through airborne infrared remote sensing

    NASA Astrophysics Data System (ADS)

    Wang, Difeng; Pan, Delu; Li, Ning

    2009-07-01

    The State Development and Planning Commission has approved nuclear power projects with the total capacity of 23,000 MW. The plants will be built in Zhejiang, Jiangsu, Guangdong, Shandong, Liaoning and Fujian Province before 2020. However, along with the nuclear power policy of accelerated development in our country, the quantity of nuclear plants and machine sets increases quickly. As a result the environment influence of thermal discharge will be a problem that can't be slid over. So evaluation of the environment influence and engineering simulation must be performed before station design and construction. Further more real-time monitoring of water temperature need to be arranged after fulfillment, reflecting variety of water temperature in time and provided to related managing department. Which will help to ensure the operation of nuclear plant would not result in excess environment breakage. At the end of 2007, an airborne thermal discharge monitoring experiment has been carried out by making use of MAMS, a marine multi-spectral scanner equipped on the China Marine Surveillance Force airplane. And experimental subject was sea area near Qin Shan nuclear plant. This paper introduces the related specification and function of MAMS instrument, and decrypts design and process of the airborne remote sensing experiment. Experiment showed that applying MAMS to monitoring thermal discharge is viable. The remote sensing on a base of thermal infrared monitoring technique told us that thermal discharge of Qin Shan nuclear plant was controlled in a small scope, never breaching national water quality standard.

  9. Application of combined Landsat thematic mapper and airborne thermal infrared multispectral scanner data to lithologic mapping in Nevada

    USGS Publications Warehouse

    Podwysocki, M.H.; Ehmann, W.J.; Brickey, D.W.

    1987-01-01

    Future Landsat satellites are to include the Thematic Mapper (TM) and also may incorporate additional multispectral scanners. One such scanner being considered for geologic and other applications is a four-channel thermal-infrared multispectral scanner having 60-m spatial resolution. This paper discusses the results of studies using combined Landsat TM and airborne Thermal Infrared Multispectral Scanner (TIMS) digital data for lithologic discrimination, identification, and geologic mapping in two areas within the Basin and Range province of Nevada. Field and laboratory reflectance spectra in the visible and reflective-infrared and laboratory spectra in the thermal-infrared parts of the spectrum were used to verify distinctions made between rock types in the image data sets.

  10. Remote sensing operations (multispectral scanner and photographic) in the New York Bight, 22 September 1975

    NASA Technical Reports Server (NTRS)

    Johnson, R. W.; Hall, J. B., Jr.

    1977-01-01

    Ocean dumping of waste materials is a significant environmental concern in the New York Bight. One of these waste materials, sewage sludge, was monitored in an experiment conducted in the New York Bight on September 22, 1975. Remote sensing over controlled sewage sludge dumping included an 11-band multispectral scanner, fiver multispectral cameras and one mapping camera. Concurrent in situ water samples were taken and acoustical measurements were made of the sewage sludge plumes. Data were obtained for sewage sludge plumes resulting from line (moving barge) and spot (stationary barge) dumps. Multiple aircraft overpasses were made to evaluate temporal effects on the plume signature.

  11. A procedure for automated land use mapping using remotely sensed multispectral scanner data

    NASA Technical Reports Server (NTRS)

    Whitley, S. L.

    1975-01-01

    A system of processing remotely sensed multispectral scanner data by computer programs to produce color-coded land use maps for large areas is described. The procedure is explained, the software and the hardware are described, and an analogous example of the procedure is presented. Detailed descriptions of the multispectral scanners currently in use are provided together with a summary of the background of current land use mapping techniques. The data analysis system used in the procedure and the pattern recognition software used are functionally described. Current efforts by the NASA Earth Resources Laboratory to evaluate operationally a less complex and less costly system are discussed in a separate section.

  12. Application research of using CASI/SASI airborne hyperspectral remote sensing on lithology identification

    NASA Astrophysics Data System (ADS)

    Zhou, Jiajing; Qin, Kai

    2016-04-01

    Remote sensing provides an advanced method for lithology identification, which is one of the important research fields in geological prospecting. In theory, each lithology is of individual spectrum characteristics. Based on the spectral differences between them, we can identify different lithologies by remote sensing images. At present, the studies on lithology identification by remote sensing are primarily conducted on the multispectral images, such as Landsat 7 ETM+, SPOT-5, QuickBird and WorldView-2. Hyperspectral remote sensing images provide richer information, making it easier to identify the lithologies, but studied rarely. CASI/SASI is an airborne hyperspectral system covering a wavelength range of 0.38-2.45μm. With hundreds of bands, the hyperspectral images are useful to identify the spectrum characteristics of lithology. In addition, images are of high spatial resolution, with CASI of about 1m and SASI of about 2-2.5m, which make lithology identification more accurate. CASI/SASI hyperspectral data was collected in Beishan metallogenic belt in northwest China, as same as the ground spectral data of the lithologies. After data preprocessing, we divided different lithologies using CASI/SASI hyperspectral images and lithology spectrum, identified some important lithologies related to mineralization, and successfully found a few new ore clues.

  13. Restoration of the missing pixel information caused by contrails in multispectral remotely sensed imagery

    NASA Astrophysics Data System (ADS)

    Zhang, Daxiang; Zhang, Chuanrong; Li, Weidong; Cromley, Robert; Hanink, Dean; Civco, Daniel; Travis, David

    2014-01-01

    Although removing the pixels covered by contrails and their shadows and restoring the missing information at the locations in remotely sensed imagery are important to understand contrails' effects on climate change, there are no such studies in the current literature. This study investigates the restoration of the missing information of the pixels caused by contrails in multispectral remotely sensed Landsat 5 TM imagery using a cokriging approach. Interpolation results and several validation methods show that it is practical to use the cokriging approach to restore the contrail-covered pixels in the multispectral remotely sensed imagery. Compared to ordinary kriging, the results are improved by taking advantage of both the spatial information in the original imagery and information from the secondary imagery.

  14. On-Orbit Calibration of a Multi-Spectral Satellite Satellite Sensor Using a High Altitude Airborne Imaging Spectrometer

    NASA Technical Reports Server (NTRS)

    Green, R. O.; Shimada, M.

    1996-01-01

    Earth-looking satellites must be calibrated in order to quantitatively measure and monitor components of land, water and atmosphere of the Earth system. The inevitable change in performance due to the stress of satellite launch requires that the calibration of a satellite sensor be established and validated on-orbit. A new approach to on-orbit satellite sensor calibration has been developed using the flight of a high altitude calibrated airborne imaging spectrometer below a multi-spectral satellite sensor.

  15. Forest Stand Segmentation Using Airborne LIDAR Data and Very High Resolution Multispectral Imagery

    NASA Astrophysics Data System (ADS)

    Dechesne, Clément; Mallet, Clément; Le Bris, Arnaud; Gouet, Valérie; Hervieu, Alexandre

    2016-06-01

    Forest stands are the basic units for forest inventory and mapping. Stands are large forested areas (e.g., ≥ 2 ha) of homogeneous tree species composition. The accurate delineation of forest stands is usually performed by visual analysis of human operators on very high resolution (VHR) optical images. This work is highly time consuming and should be automated for scalability purposes. In this paper, a method based on the fusion of airborne laser scanning data (or lidar) and very high resolution multispectral imagery for automatic forest stand delineation and forest land-cover database update is proposed. The multispectral images give access to the tree species whereas 3D lidar point clouds provide geometric information on the trees. Therefore, multi-modal features are computed, both at pixel and object levels. The objects are individual trees extracted from lidar data. A supervised classification is performed at the object level on the computed features in order to coarsely discriminate the existing tree species in the area of interest. The analysis at tree level is particularly relevant since it significantly improves the tree species classification. A probability map is generated through the tree species classification and inserted with the pixel-based features map in an energetical framework. The proposed energy is then minimized using a standard graph-cut method (namely QPBO with α-expansion) in order to produce a segmentation map with a controlled level of details. Comparison with an existing forest land cover database shows that our method provides satisfactory results both in terms of stand labelling and delineation (matching ranges between 94% and 99%).

  16. Mapping of hydrothermally altered rocks using airborne multispectral scanner data, Marysvale, Utah, mining district

    USGS Publications Warehouse

    Podwysocki, M.H.; Segal, D.B.; Jones, O.D.

    1983-01-01

    Multispectral data covering an area near Marysvale, Utah, collected with the airborne National Aeronautics and Space Administration (NASA) 24-channel Bendix multispectral scanner, were analyzed to detect areas of hydrothermally altered, potentially mineralized rocks. Spectral bands were selected for analysis that approximate those of the Landsat 4 Thematic Mapper and which are diagnostic of the presence of hydrothermally derived products. Hydrothermally altered rocks, particularly volcanic rocks affected by solutions rich in sulfuric acid, are commonly characterized by concentrations of argillic minerals such as alunite and kaolinite. These minerals are important for identifying hydrothermally altered rocks in multispectral images because they have intense absorption bands centered near a wavelength of 2.2 ??m. Unaltered volcanic rocks commonly do not contain these minerals and hence do not have the absorption bands. A color-composite image was constructed using the following spectral band ratios: 1.6??m/2.2??m, 1.6??m/0.48??m, and 0.67??m/1.0??m. The particular bands were chosen to emphasize the spectral contrasts that exist for argillic versus non-argillic rocks, limonitic versus nonlimonitic rocks, and rocks versus vegetation, respectively. The color-ratio composite successfully distinguished most types of altered rocks from unaltered rocks. Some previously unrecognized areas of hydrothermal alteration were mapped. The altered rocks included those having high alunite and/or kaolinite content, siliceous rocks containing some kaolinite, and ash-fall tuffs containing zeolitic minerals. The color-ratio-composite image allowed further division of these rocks into limonitic and nonlimonitic phases. The image did not allow separation of highly siliceous or hematitically altered rocks containing no clays or alunite from unaltered rocks. A color-coded density slice image of the 1.6??m/2.2??m band ratio allowed further discrimination among the altered units. Areas

  17. An Assessment Of Meso-Scale Hydraulic And Vegetation Characteristics Of The Middle Rio Grande River Using High Resolution Multispectral Airborne Imagery

    NASA Astrophysics Data System (ADS)

    Akasheh, O. Z.; Neale, C. M.

    2004-12-01

    Middle Rio Grande River (MRGR) is the main source of fresh water for the population of New Mexico as well as for irrigated agriculture. Extensive water diversion over the last few decades has affected the composition of the native Riparian vegetation such as Cottonwood population and enhanced the spread of introduced species harmful to the river system like Tamarisk and Russian Olives. High resolution airborne remote sensing is a powerful technique for riparian vegetation mapping and monitoring. Airborne multispectral digital images were acquired over the riparian corridor of the MRGR, New Mexico in June 1999 and July 2001, using the Utah State University (USU) airborne digital imaging system. The imagery were corrected for vignetting effects, geometric lens distortions, rectified to a map base, mosaicked, verified in the field, classified and checked for accuracy. Areas of the vegetation classes and in-stream features were extracted and presented per reach of the river. In this paper a relationship was developed between the total surface water area mapped and both the river water flow rate and water table readings. The consequence of this relationship on riparian vegetation distribution along the river was studied and graphically demonstrated. Strong relationship was found between the total surface water area and water flow rate. In addition the reduction in surface water area resulted in reduction of native trees downstream.

  18. Remote sensing at Savannah River

    SciTech Connect

    Corey, J.C.

    1986-01-01

    The paper discusses remote sensing systems used at the Savannah River Plant. They include three ground-based systems: ground penetrating radar, sniffers, and lasers; and four airborne systems: multispectral photography, lasers, thermal imaging, and radar systems. (ACR)

  19. An airborne remote sensing system for urban air quality

    NASA Technical Reports Server (NTRS)

    Duncan, L. J.; Friedman, E. J.; Keitz, E. L.; Ward, E. A.

    1974-01-01

    Several NASA sponsored remote sensors and possible airborne platforms were evaluated. Outputs of dispersion models for SO2 and CO pollution in the Washington, D.C. area were used with ground station data to establish the expected performance and limitations of the remote sensors. Aircraft/sensor support requirements are discussed. A method of optimum flight plan determination was made. Cost trade offs were performed. Conclusions about the implementation of various instrument packages as parts of a comprehensive air quality monitoring system in Washington are presented.

  20. Airborne Thermal Infrared Multispectral Scanner (TIMS) images over disseminated gold deposits, Osgood Mountains, Humboldt County, Nevada

    NASA Technical Reports Server (NTRS)

    Krohn, M. Dennis

    1986-01-01

    The U.S. Geological Survey (USGS) acquired airborne Thermal Infrared Multispectral Scanner (TIMS) images over several disseminated gold deposits in northern Nevada in 1983. The aerial surveys were flown to determine whether TIMS data could depict jasperoids (siliceous replacement bodies) associated with the gold deposits. The TIMS data were collected over the Pinson and Getchell Mines in the Osgood Mountains, the Carlin, Maggie Creek, Bootstrap, and other mines in the Tuscarora Mountains, and the Jerritt Canyon Mine in the Independence Mountains. The TIMS data seem to be a useful supplement to conventional geochemical exploration for disseminated gold deposits in the western United States. Siliceous outcrops are readily separable in the TIMS image from other types of host rocks. Different forms of silicification are not readily separable, yet, due to limitations of spatial resolution and spectral dynamic range. Features associated with the disseminated gold deposits, such as the large intrusive bodies and fault structures, are also resolvable on TIMS data. Inclusion of high-resolution thermal inertia data would be a useful supplement to the TIMS data.

  1. Remote sensing of shorelines using data fusion of hyperspectral and multispectral imagery acquired from mobile and fixed platforms

    NASA Astrophysics Data System (ADS)

    Bostater, Charles R.; Frystacky, Heather

    2012-06-01

    An optimized data fusion methodology is presented and makes use of airborne and vessel mounted hyperspectral and multispectral imagery acquired at littoral zones in Florida and the northern Gulf of Mexico. The results demonstrate the use of hyperspectral-multispectral data fusion anomaly detection along shorelines and in surface and subsurface waters. Hyperspectral imagery utilized in the data fusion analysis was collected using a 64-1024 channel, 1376 pixel swath width; temperature stabilized sensing system; an integrated inertial motion unit; and differential GPS. The imaging system is calibrated using dual 18 inch calibration spheres, spectral line sources, and custom line targets. Simultaneously collected multispectral three band imagery used in the data fusion analysis was derived either a 12 inch focal length large format camera using 9 inch high speed AGFA color negative film, a 12.3 megapixel digital camera or dual high speed full definition video cameras. Pushbroom sensor imagery is corrected using Kalman filtering and smoothing in order to correct images for airborne platform motions or motions of a small vessel. Custom software developed for the hyperspectral system and the optimized data fusion process allows for post processing using atmospherically corrected and georeferenced reflectance imagery. The optimized data fusion approach allows for detecting spectral anomalies in the resolution enhanced data cubes. Spectral-spatial anomaly detection is demonstrated using simulated embedded targets in actual imagery. The approach allows one to utilize spectral signature anomalies to identify features and targets that would otherwise not be possible. The optimized data fusion techniques and software has been developed in order to perform sensitivity analysis of the synthetic images in order to optimize the singular value decomposition model building process and the 2-D Butterworth cutoff frequency selection process, using the concept of user defined "feature

  2. Computational modeling of multispectral remote sensing systems: Background investigations

    NASA Technical Reports Server (NTRS)

    Aherron, R. M.

    1982-01-01

    A computational model of the deterministic and stochastic process of remote sensing has been developed based upon the results of the investigations presented. The model is used in studying concepts for improving worldwide environment and resource monitoring. A review of various atmospheric radiative transfer models is presented as well as details of the selected model. Functional forms for spectral diffuse reflectance with variability introduced are also presented. A cloud detection algorithm and the stochastic nature of remote sensing data with its implications are considered.

  3. Actual evapotranspiration estimation by means of airborne and satellite remote sensing data

    NASA Astrophysics Data System (ADS)

    Ciraolo, Giuseppe; D'Urso, Guido; Minacapilli, Mario

    2006-09-01

    During the last the two decades, the scientific community developed detailed mathematical models for simulating land surface energy fluxes and crop evapotranspiration rates by means of a energy balance approach. These models can be applied in large areas and with a spatial distributed approach using surface brightness temperature and some ancillary data retrieved from satellite/airborne remote sensed imagery. In this paper a district scale application in combination with multispectral (LandaSat 7 TM data) and hyperspectral airborne MIVIS data has been carried out to test the potentialities of two different energy balance models to estimate evapotranspiration fluxes from a set of typical Mediterranean crops (wine, olive, citrus). The impact of different spatial and radiometric resolutions of MIVIS (3m x 3m) and LandSat (60m x 60m) on models-derived fluxes has been investigated to understand the roles and the main conceptual differences between the two models which respectively use a "single-layer" (SEBAL) and a "two-layer" (TS) schematisation.

  4. Comparison between laboratory and airborne BRDF measurements for remote sensing

    NASA Astrophysics Data System (ADS)

    Georgiev, Georgi T.; Gatebe, Charles K.; Butler, James J.; King, Michael D.

    2006-08-01

    Samples from soil and leaf litter were obtained at a site located in the savanna biome of South Africa (Skukuza; 25.0°S, 31.5°E) and their bidirectional reflectance distribution functions (BRDF) were measured using the out-of-plane scatterometer located in the National Aeronautics and Space Administration's (NASA's) Goddard Space Flight Center (GSFC) Diffuser Calibration Facility (DCaF). BRDF was measured using P and S incident polarized light over a range of incident and scatter angles. A monochromator-based broadband light source was used in the ultraviolet (uv) and visible (vis) spectral ranges. The diffuse scattered light was collected using an uv-enhanced silicon photodiode detector with output fed to a computer-controlled lock-in amplifier. Typical measurement uncertainties of the reported laboratory BRDF measurements are found to be less than 1% (k=1). These laboratory results were compared with airborne measurements of BRDF from NASA's Cloud Absorption Radiometer (CAR) instrument over the same general site where the samples were obtained. This study presents preliminary results of the comparison between these laboratory and airborne BRDF measurements and identifies areas for future laboratory and airborne BRDF measurements. This paper presents initial results in a study to try to understand BRDF measurements from laboratory, airborne, and satellite measurements in an attempt to improve the consistency of remote sensing models.

  5. A new method of building footprints detection using airborne laser scanning data and multispectral image

    NASA Astrophysics Data System (ADS)

    Luo, Yiping; Jiang, Ting; Gao, Shengli; Wang, Xin

    2010-10-01

    It presents a new approach for detecting building footprints in a combination of registered aerial image with multispectral bands and airborne laser scanning data synchronously obtained by Leica-Geosystems ALS40 and Applanix DACS-301 on the same platform. A two-step method for building detection was presented consisting of selecting 'building' candidate points and then classifying candidate points. A digital surface model(DSM) derived from last pulse laser scanning data was first filtered and the laser points were classified into classes 'ground' and 'building or tree' based on mathematic morphological filter. Then, 'ground' points were resample into digital elevation model(DEM), and a Normalized DSM(nDSM) was generated from DEM and DSM. The candidate points were selected from 'building or tree' points by height value and area threshold in nDSM. The candidate points were further classified into building points and tree points by using the support vector machines(SVM) classification method. Two classification tests were carried out using features only from laser scanning data and associated features from two input data sources. The features included height, height finite difference, RGB bands value, and so on. The RGB value of points was acquired by matching laser scanning data and image using collinear equation. The features of training points were presented as input data for SVM classification method, and cross validation was used to select best classification parameters. The determinant function could be constructed by the classification parameters and the class of candidate points was determined by determinant function. The result showed that associated features from two input data sources were superior to features only from laser scanning data. The accuracy of more than 90% was achieved for buildings in first kind of features.

  6. Location of the Rhine plume front by airborne remote sensing

    NASA Astrophysics Data System (ADS)

    Ruddick, K. G.; Lahousse, L.; Donnay, E.

    1994-04-01

    The aim of this study was to determine the feasibility of using airborne remote sensing to locate the Rhine plume front. Interest in fronts arises from the desire to predict the fate of pollutants and biological nutrients discharged from rivers into the open sea. Observations were made during flights over the Dutch coastal waters using a vertically-mounted video camera and a side-looking airborne radar (SLAR) designed for oil slick detection. Comparison of radar images with visual observations of the sea colour discontinuity and foam line establish that fronts can indeed be detected by SLAR because of high radar backscatter along the convergence line, where the fresh water jet impinges on saltier water. This provides a sound basis for future investigations using Synthetic Aperture Radar as mounted on ERS-1. An estimation of errors is given, identifying priorities for improvement of the technique. The accuracy achieved is considered sufficient for the validation of hydrodynamic models.

  7. Automation of hyperspectral airborne remote sensing data processing

    NASA Astrophysics Data System (ADS)

    Kozoderov, V. V.; Egorov, V. D.

    2014-12-01

    An automated system is proposed for discriminating the spectral radiances registered by the hyperspectral airborne instruments based on average spectra and their interclass variability while distinguishing pixels related to the illuminated and shaded elements of the crown trees for various species and ages. Maps of the ground-based inventory for the selected area of airborne remote sensing are used as prior information. The system automatically forms databases of the selected classes of objects using the contours of these objects drawn on the image under processing. An opportunity to distinguish these classes is demonstrated in the red edge region of the spectra transition from the chlorophyll spectral band to the maximum of the spectral vegetation reflectivity.

  8. Evaluation method of water quality for river based on multi-spectral remote sensing data

    NASA Astrophysics Data System (ADS)

    Xiao, X.; Jian, X.; Xiongfei, W.; Chengfang, H.; Xuejun, C.; Zhaohui, W.; Dengzhong, Z.

    2015-04-01

    With the rapid development of the regional economy, water pollution has gradually become an environmental problem that cannot be ignored. As an important water source in central China, the Han River should strengthen water quality monitoring and management in order to ensure the sustainable development of watershed and related areas. Taking typical sections of middle and lower reaches of the Han River as the study area, this paper focuses on rapid river water quality assessment using multispectral remote sensing images. Based on measured water quality data and synchronous spatial high and medium-resolution remote sensing data (multi-spectral data of ZY3 and HJ1A) in 2013, neural network algorithm is used to establish water quality index retrieval model for the study area, and then water quality status is assessed accordingly. The results show that BP neural network retrieval model of water quality index that is established based on multispectral data of ZY3 satellite has higher accuracy and that its assessment results are of high credibility and strong applicability, which can really reflect changes in water quality and better achieve water quality assessment for the study area. In addition, water quality assessment results show that major excessive factors in the study area are total nitrogen and total phosphorus; the polluting type is organic pollution; water quality varies greatly with seasons.

  9. High-precision geometric correction of airborne remote sensing revisited: the multiquadric interpolation

    NASA Astrophysics Data System (ADS)

    Ehlers, Manfred; Fogel, David N.

    1994-12-01

    For a geographic analysis of multispectral scanner data from aircraft and their integration in spatial databases and geographic integration systems (GIS), geometric registration/rectification of the scanner imagery is required as a first step. Usually, one has to rely on global mapping functions such as polynomial equations as provided by most commercial image processing systems. These techniques have been proven to be very effective and accurate for satellite images. However, there are a umber of shortcomings when this method is applied to aircraft data. We see the multiquadric interpolation method as a promising alternative. The multiquadric function was first developed for the interpolation of irregular surfaces. It could be modified, however, to be used for image correction of remotely sensed data. In this form, it is particularly suited for the rectification of remote sensing images of large scale and locally varying geometric distortions. The multiquadric interpolation method yields a perfect fit at the used control points (CPs). With this, it is necessary to withhold independent test points that can be used for accuracy assessment. Within the registration/rectification process, all CPs contribute to the geometric warping of any given pixel in the image. Their effects, however, are weighted inversely to the distances between CPs and the current pixel location. The paper presents the multiquadric interpolation techniques and demonstrates successful application with airborne scanner data.

  10. Pan-Sharpening Approaches Based on Unmixing of Multispectral Remote Sensing Imagery

    NASA Astrophysics Data System (ADS)

    Palubinskas, G.

    2016-06-01

    Model based analysis or explicit definition/listing of all models/assumptions used in the derivation of a pan-sharpening method allows us to understand the rationale or properties of existing methods and shows a way for a proper usage or proposal/selection of new methods `better' satisfying the needs of a particular application. Most existing pan-sharpening methods are based mainly on the two models/assumptions: spectral consistency for high resolution multispectral data (physical relationship between multispectral and panchromatic data in a high resolution scale) and spatial consistency for multispectral data (so-called Wald's protocol first property or relationship between multispectral data in different resolution scales). Two methods, one based on a linear unmixing model and another one based on spatial unmixing, are described/proposed/modified which respect models assumed and thus can produce correct or physically justified fusion results. Earlier mentioned property `better' should be measurable quantitatively, e.g. by means of so-called quality measures. The difficulty of a quality assessment task in multi-resolution image fusion or pan-sharpening is that a reference image is missing. Existing measures or so-called protocols are still not satisfactory because quite often the rationale or assumptions used are not valid or not fulfilled. From a model based view it follows naturally that a quality assessment measure can be defined as a combination of error model residuals using common or general models assumed in all fusion methods. Thus in this paper a comparison of the two earlier proposed/modified pan-sharpening methods is performed. Preliminary experiments based on visual analysis are carried out in the urban area of Munich city for optical remote sensing multispectral data and panchromatic imagery of the WorldView-2 satellite sensor.

  11. Discrimination techniques employing both reflective and thermal multispectral signals. [for remote sensor technology

    NASA Technical Reports Server (NTRS)

    Malila, W. A.; Crane, R. B.; Richardson, W.

    1973-01-01

    Recent improvements in remote sensor technology carry implications for data processing. Multispectral line scanners now exist that can collect data simultaneously and in registration in multiple channels at both reflective and thermal (emissive) wavelengths. Progress in dealing with two resultant recognition processing problems is discussed: (1) More channels mean higher processing costs; to combat these costs, a new and faster procedure for selecting subsets of channels has been developed. (2) Differences between thermal and reflective characteristics influence recognition processing; to illustrate the magnitude of these differences, some explanatory calculations are presented. Also introduced, is a different way to process multispectral scanner data, namely, radiation balance mapping and related procedures. Techniques and potentials are discussed and examples presented.

  12. Simulation of electronic registration of multispectral remote sensing images to 0.1 pixel accuracy

    NASA Technical Reports Server (NTRS)

    Reitsema, H. J.; Mord, A. J.; Fraser, D.; Richard, H. L.; Speaker, E. E.

    1984-01-01

    Band-to-band coregistration of multispectral remote sensing images can be achieved by electronic signal processing techniques rather than by costly and difficult mechanical alignment. This paper describes the results of a study of the end-to-end performance of electronic registration. The software simulation includes steps which model the performance of the geometric calibration process, the instrument image quality, detector performance and the effects of achieving coregistration through image resampling. The image resampling step emulates the Pipelined Resampling Processor, a real-time image resampler. The study demonstrates that the electronic alignment technique produces multispectral images which are superior to those produced by an imager whose pixel geometry is accurate to 0.1 pixel rms. The implications of this approach for future earth observation programs are discussed.

  13. Using remotely-sensed multispectral imagery to build age models for alluvial fan surfaces

    NASA Astrophysics Data System (ADS)

    D'Arcy, Mitch; Mason, Philippa J.; Roda Boluda, Duna C.; Whittaker, Alexander C.; Lewis, James

    2016-04-01

    Accurate exposure age models are essential for much geomorphological field research, and generally depend on laboratory analyses such as radiocarbon, cosmogenic nuclide, or luminescence techniques. These approaches continue to revolutionise geomorphology, however they cannot be deployed remotely or in situ in the field. Therefore other methods are still needed for producing preliminary age models, performing relative dating of surfaces, or selecting sampling sites for the laboratory analyses above. With the widespread availability of detailed multispectral imagery, a promising approach is to use remotely-sensed data to discriminate surfaces with different ages. Here, we use new Landsat 8 Operational Land Imager (OLI) multispectral imagery to characterise the reflectance of 35 alluvial fan surfaces in the semi-arid Owens Valley, California. Alluvial fans are useful landforms to date, as they are widely used to study the effects of tectonics, climate and sediment transport processes on source-to-sink sedimentation. Our target fan surfaces have all been mapped in detail in the field, and have well-constrained exposure ages ranging from modern to ~ 125 ka measured using a high density of 10Be cosmogenic nuclide samples. Despite all having similar granitic compositions, the spectral properties of these surfaces vary systematically with their exposure ages. Older surfaces demonstrate a predictable shift in reflectance across the visible and short-wave infrared spectrum. Simple calculations, such as the brightness ratios of different wavelengths, generate sensitive power law relationships with exposure age that depend on post-depositional alteration processes affecting these surfaces. We investigate what these processes might be in this dryland location, and evaluate the potential for using remotely-sensed multispectral imagery for developing surface age models. The ability to remotely sense relative exposure ages has useful implications for preliminary mapping, selecting

  14. Modular airborne remote sampling and sensing system (MARSSS)

    SciTech Connect

    Woods, R.O.

    1982-04-01

    Sandia is developing a modular airborne instrumentation system for the Environmental Protection Agency. This system will allow flexibility in the choice of instruments by standardizing mountings, power supplies and sampling modes. The objective is to make it possible to perform aerial surveys from chartered aircraft that have not been adapted in a more than superficial manner. It will also allow the experimenter to tailor his choice of instruments to the specific problem. Since the equipment will have a stand-alone capability, it can be applied to other problems such as long-term unattended use at remote locations or in toxic or otherwise hazardous environments.

  15. Quantitative suspended sediment mapping using aircraft remotely sensed multispectral data. [in Virginia

    NASA Technical Reports Server (NTRS)

    Johnson, R. W.

    1975-01-01

    Suspended sediment is an important environmental parameter for monitoring water quality, water movement, and land use. Quantitative suspended sediment determinations were made from analysis of aircraft remotely sensed multispectral digital data. A statistical analysis and derived regression equation were used to determine and plot quantitative suspended sediment concentration contours in the tidal James River, Virginia, on May 28, 1974. From the analysis, a single band, Band 8 (0.70-0.74 microns), was adequate for determining suspended sediment concentrations. A correlation coefficient of 0.89 was obtained with a mean inaccuracy of 23.5 percent for suspended sediment concentrations up to about 50 mg/l. Other water quality parameters - secchi disc depth and chlorophyll - also had high correlations with the remotely sensed data. Particle size distribution had only a fair correlation with the remotely sensed data.

  16. Ground-based multispectral measurements for airborne data verification in non-operating open pit mine "Kremikovtsi"

    NASA Astrophysics Data System (ADS)

    Borisova, Denitsa; Nikolov, Hristo; Petkov, Doyno

    2013-10-01

    The impact of mining industry and metal production on the environment is presented all over the world. In our research we set focus on the impact of already non-operating ferrous "Kremikovtsi"open pit mine and related waste dumps and tailings which we consider to be the major factor responsible for pollution of one densely populated region in Bulgaria. The approach adopted is based on correct estimation of the distribution of the iron oxides inside open pit mines and the neighboring regions those considered in this case to be the key issue for the ecological state assessment of soils, vegetation and water. For this study the foremost source of data are those of airborne origin and those combined with ground-based in-situ and laboratory acquired data were used for verification of the environmental variables and thus in process of assessment of the present environmental status influenced by previous mining activities. The percentage of iron content was selected as main indicator for presence of metal pollution since it could be reliably identified by multispectral data used in this study and also because the iron compounds are widely spread in the most of the minerals, rocks and soils. In our research the number of samples from every source (air, field, lab) was taken in the way to be statistically sound and confident. In order to establish relationship between the degree of pollution of the soil and mulspectral data 40 soil samples were collected during a field campaign in the study area together with GPS measurements for two types of laboratory measurements: the first one, chemical and mineralogical analysis and the second one, non-destructive spectroscopy. In this work for environmental variables verification over large areas mulspectral satellite data from Landsat instruments TM/ETM+ and from ALI/OLI (Operational Land Imager) were used. Ground-based (laboratory and in-situ) spectrometric measurements were performed using the designed and constructed in Remote

  17. Winter wheat nutrition diagnosis under different N treatments based on multispectral images and remote sensing

    NASA Astrophysics Data System (ADS)

    Zhao, Ruijiao; Li, Minzan; Li, Shuqiang; Ding, Yongjun

    2010-11-01

    In order to rapidly and accurately acquire winter wheat growing information and nitrogen content, a non-destructive testing method was developed combined with multi-spectral imaging technique and remote sensing technology to research wheat growing and nutrition status. Firstly, a 2-CCD multi-spectral image collecting platform was developed to acquire visible image and NIR image synchronously, meanwhile, the canopy spectral reflectance and the nitrogen content of wheat leaves were measured and analyzed to research the characteristics of the canopy spectral reflectance. Secondly, using calibration panels the experiential linear calibration model was established between image gray value and spectral reflectance. Thirdly, NIR image was processed to segment wheat canopy from soil and then gray value of wheat leaves was achieved by image processing of Red, Green, and Blue channels. Finally, the gray value of wheat leaves was transformed into spectral reflectance by aforementioned experiential linear model, and the vegetation index were calculated and analyzed to research the winter wheat growing and nitrogen content status. Experiment results showed that it was reasonable to diagnose nitrogen content of winter wheat based on multi-spectral imaging system and experiential linear model. There existed remarkable correlation between vegetation index (NDVI, GNDVI) and nitrogen content of winter wheat, and the correlation coefficients (R2 ) were 0.633 and 0.6.

  18. Fusion of remotely sensed data from airborne and ground-based sensors to enhance detection of cotton plants

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The study investigated the use of aerial multispectral imagery and ground-based hyperspectral data for the discrimination of different crop types and timely detection of cotton plants over large areas. Airborne multispectral imagery and ground-based spectral reflectance data were acquired at the sa...

  19. Hydrological characterization of a riparian vegetation zone using high resolution multi-spectral airborne imagery

    NASA Astrophysics Data System (ADS)

    Akasheh, Osama Z.

    The Middle Rio Grande River (MRGR) is the main source of fresh water for the state of New Mexico. Located in an arid area with scarce local water resources, this has led to extensive diversions of river water to supply the high demand from municipalities and irrigated agricultural activities. The extensive water diversions over the last few decades have affected the composition of the native riparian vegetation by decreasing the area of cottonwood and coyote willow and increasing the spread of invasive species such as Tamarisk and Russian Olives, harmful to the river system, due to their high transpiration rates, which affect the river aquatic system. The need to study the river hydrological processes and their relation with its health is important to preserve the river ecosystem. To be able to do that a detailed vegetation map was produced using a Utah State University airborne remote sensing system for 286 km of river reach. Also a groundwater model was built in ArcGIS environment which has the ability to estimate soil water potential in the root zone and above the modeled water table. The Modified Penman-Monteith empirical equation was used in the ArcGIS environment to estimate riparian vegetation ET, taking advantage of the detailed vegetation map and spatial soil water potential layers. Vegetation water use per linear river reach was estimated to help decision makers to better manage and release the amount of water that keeps a sound river ecosystem and to support agricultural activities.

  20. Remote sensing of benthic microalgal biomass with a tower-mounted multispectral scanner

    NASA Technical Reports Server (NTRS)

    Jobson, D. J.; Katzberg, S. J.; Zingmark, R. G.

    1980-01-01

    A remote sensing instrument was mounted on a 50-ft tower overlooking North Inlet Estuary, South Carolina in order to conduct a remote sensing study of benthic microalgae. The instrument was programmed to take multispectral imagery data along a 90 deg horizontal frame in six spectral bands ranging from 400-1050 nm and had a ground resolution of about 3 cm. Imagery measurements were encoded in digital form on magnetic tape and were stored, decoded, and manipulated by computer. Correlation coefficients were calculated on imagery data and chlorophyll a concentrations derived from ground truth data. The most significant correlation occurred in the blue spectral band with numerical values ranging from -0.81 to -0.88 for three separate sampling periods. Mean values of chlorophyll a for a larger section of mudflat were estimated using regression equations. The scanner has provided encouraging results and promises to be a useful tool in sampling the biomass of intertidal benthic microalgae.

  1. Operational considerations for the application of remotely sensed forest data from LANDSAT or other airborne platforms

    NASA Technical Reports Server (NTRS)

    Baker, G. R.; Fethe, T. P.

    1975-01-01

    Research in the application of remotely sensed data from LANDSAT or other airborne platforms to the efficient management of a large timber based forest industry was divided into three phases: (1) establishment of a photo/ground sample correlation, (2) investigation of techniques for multi-spectral digital analysis, and (3) development of a semi-automated multi-level sampling system. To properly verify results, three distinct test areas were selected: (1) Jacksonville Mill Region, Lower Coastal Plain, Flatwoods, (2) Pensacola Mill Region, Middle Coastal Plain, and (3) Mississippi Mill Region, Middle Coastal Plain. The following conclusions were reached: (1) the probability of establishing an information base suitable for management requirements through a photo/ground double sampling procedure, alleviating the ground sampling effort, is encouraging, (2) known classification techniques must be investigated to ascertain the level of precision possible in separating the many densities involved, and (3) the multi-level approach must be related to an information system that is executable and feasible.

  2. [Vegetation water content retrieval and application of drought monitoring using multi-spectral remote sensing].

    PubMed

    Wang, Li-Tao; Wang, Shi-Xin; Zhou, Yi; Liu, Wen-Liang; Wang, Fu-Tao

    2011-10-01

    The vegetation is one of main drying carriers. The change of Vegetation Water Content (VWC) reflects the spatial-temporal distribution of drought situation and the degree of drought. In the present paper, a method of retrieving the VWC based on remote sensing data is introduced and analyzed, including the monitoring theory, vegetation water content indicator and retrieving model. The application was carried out in the region of Southwest China in the spring, 2010. The VWC data was calculated from MODIS data and spatially-temporally analyzed. Combined with the meteorological data from weather stations, the relationship between the EWT and weather data shows that precipitation has impact on the change in vegetation moisture to a certain extent. However, there is a process of delay during the course of vegetation absorbing water. So precipitation has a delaying impact on VWC. Based on the above analysis, the probability of drought monitoring and evaluation based on multi-spectral VWC data was discussed. Through temporal synthesis and combined with auxiliary data (i. e. historical data), it will help overcome the limitation of data itself and enhance the application of drought monitoring and evaluation based on the multi-spectral remote sensing. PMID:22250560

  3. [Classification of wetlands in multispectral remote sensing image based on HPSO and FCM].

    PubMed

    Jiang, Wei-Guo; Chen, Qiang; Guo, Ji; Tang, Hong; Li, Xue

    2010-12-01

    The present paper analyzed the characteristics of particle swarm optimization(PSO), hybrid particle swarm optimization (HPSO) and fuzzy C-means (FCM), imported FCM into HPSO, and improved the HPSO-FCM arithmetic. An HPSO-FCM program was developed using Fortran language in MATLAB. Besides, a synthesis image combined with the former three principal components was obtained through band stacking and principal component analysis, taking the multispectral visible image of HJ-1 Satellite shot in June 2009 and the ASAR radar image of ENVISAT as basic data. And the paper has done a wetlands classification experiment in the synthesis image of the East Dongting Lake of Hunan province, using HPSO-FCM arithmetic and ISODATA separately. The results indicated: (1) The arithmetic which imported crossover operator of genetic algorithms and FCM into HPSO had better search speed and convergent precision, and it could search and optimize the best cluster center more efficiently. (2) The HPSO-FCM arithmetic has better precision in wetlands classification in multispectral remote sensing image, and it is an effective method in remote sensing image classification. PMID:21322233

  4. Anisotropic spectral-spatial total variation model for multispectral remote sensing image destriping.

    PubMed

    Chang, Yi; Yan, Luxin; Fang, Houzhang; Luo, Chunan

    2015-06-01

    Multispectral remote sensing images often suffer from the common problem of stripe noise, which greatly degrades the imaging quality and limits the precision of the subsequent processing. The conventional destriping approaches usually remove stripe noise band by band, and show their limitations on different types of stripe noise. In this paper, we tentatively categorize the stripes in remote sensing images in a more comprehensive manner. We propose to treat the multispectral images as a spectral-spatial volume and pose an anisotropic spectral-spatial total variation regularization to enhance the smoothness of solution along both the spectral and spatial dimension. As a result, a more comprehensive stripes and random noise are perfectly removed, while the edges and detail information are well preserved. In addition, the split Bregman iteration method is employed to solve the resulting minimization problem, which highly reduces the computational load. We extensively validate our method under various stripe categories and show comparison with other approaches with respect to result quality, running time, and quantitative assessments. PMID:25706634

  5. Mapping of Coral Reef Environment in the Arabian Gulf Using Multispectral Remote Sensing

    NASA Astrophysics Data System (ADS)

    Ben-Romdhane, H.; Marpu, P. R.; Ghedira, H.; Ouarda, T. B. M. J.

    2016-06-01

    Coral reefs of the Arabian Gulf are subject to several pressures, thus requiring conservation actions. Well-designed conservation plans involve efficient mapping and monitoring systems. Satellite remote sensing is a cost-effective tool for seafloor mapping at large scales. Multispectral remote sensing of coastal habitats, like those of the Arabian Gulf, presents a special challenge due to their complexity and heterogeneity. The present study evaluates the potential of multispectral sensor DubaiSat-2 in mapping benthic communities of United Arab Emirates. We propose to use a spectral-spatial method that includes multilevel segmentation, nonlinear feature analysis and ensemble learning methods. Support Vector Machine (SVM) is used for comparison of classification performances. Comparative data were derived from the habitat maps published by the Environment Agency-Abu Dhabi. The spectral-spatial method produced 96.41% mapping accuracy. SVM classification is assessed to be 94.17% accurate. The adaptation of these methods can help achieving well-designed coastal management plans in the region.

  6. Airborne imaging spectrometer - A new tool for remote sensing

    NASA Technical Reports Server (NTRS)

    Vane, G.; Goetz, A. F. H.; Wellman, J. B.

    1983-01-01

    The first of a new class of remote sensing instruments is described. The Airborne Imaging Spectrometer represents the first use of two-dimensional area arrays in a scientific application. The instrument images 32 cross-track pixels simultaneously, each in 128 spectral bands in the 1.2 to 2.4 micro region. The IFOV of the instrument is 1.9 mrad and the spectral sampling interval is 9.6 nanometers. Plans include upgrading the detector from the current 32 x 32 element HgCdTe CCD array to a 64 x 64 element array in 1984. Science and engineering data are currently being actively gathered with the instrument.

  7. Airborne imaging spectrometer - A new tool for remote sensing

    NASA Technical Reports Server (NTRS)

    Vane, G.; Goetz, A. F. H.; Wellman, J. B.

    1984-01-01

    The first of a new class of remote sensing instruments is described. The Airborne Imaging Spectrometer represents the first use of two-dimensional integrated infrared area arrays in a scientific application. The instrument images 32 cross-track pixels simultaneously, each in 128 spectral bands in the 1.2- to 2.4-micron region. The IFOV of the instrument is 1.9 mrad/pixel and the spectral sampling interval is 9.6 nm. Plans include upgrading the detector from the current 32 x 32 element HgCdTe CCD array to a 64 x 64 element array in 1985. Science and engineering data are currently being actively gathered with the instrument.

  8. Airborne remote sensing of coal waste and acid mine drainage

    SciTech Connect

    Kim, K.E.; Lee, T.S.

    1996-07-01

    High resolution airborne remote sensing data, spatial resolution of 2m X 2m, were used to study the stream quality degradation due to the coal mines in Taebaek city, one of the major coalfields in Korea. In order to circumvent the severe topographic effect and small scale of the water stream, principal components with the least variances were utilized. They showed the subtle details in the image that were obscured by higher contrast due to the topographic effect. Through maximum likelihood classification of those components, yellowboy and mine waste could be effectively identified. Areas affected by acid mine drainage and mine waste could be also located by identifying areas of dead or dying vegetation using vegetation index map.

  9. Second International Airborne Remote Sensing Conference and Exhibition

    NASA Technical Reports Server (NTRS)

    1996-01-01

    cloud cover analysis, Quadantid meteor shower studies, extra-solar far infrared ionic structure lines measurement, Cape Kennedy launch support, and studies in air pollution, The Products and Services Exhibit showcased new sensor and image processing technologies, aircraft data collection services, unmanned vehicle technology, platform equipment, turn-key services, software a workstations, GPS services, publications, and processing and integration systems by 58 exhibitors. The participation of aircraft users and crews provided unique dialogue between those who plan data collection a operate the remote sensing technology, and those who supply the data processing and integration equipment. Research results using hyperspectral imagery, radar and optical sensors, lidar, digital aerial photography, a integrated systems were presented. Major research and development programs and campaigns we reviewed, including CNR's LARA Project and European Space Agency's 1991-1995 Airborne Campaign. The pre-conference short courses addressed airborne video, photogrammetry, hyperspectral data analysis, digital orthophotography, imagery and GIS integration, IFSAR, GPS, and spectrometer calibration.

  10. Supporting relief efforts of the 2010 Haitian earthquake using an airborne multimodal remote sensing platform

    NASA Astrophysics Data System (ADS)

    Faulring, Jason W.; McKeown, Donald M.; van Aardt, Jan; Casterline, May V.; Bartlett, Brent D.; Raqueno, Nina

    2011-06-01

    The small island nation of Haiti was devastated in early 2010 following a massive 7.0 earthquake that brought about widespread destruction of infrastructure, many deaths and large-scale displacement of the population in the nation's major cities. The World Bank and ImageCat, Inc tasked the Rochester Institute of Technology's (RIT) Wildfire Airborne Sensor Platform (WASP) to gather a multi-spectral and multi-modal assessment of the disaster over a seven-day period to be used for relief and reconstruction efforts. Traditionally, private sector aerial remote sensing platforms work on processing and product delivery timelines measured in days, a scenario that has the potential to reduce the value of the data in time-sensitive situations such as those found in responding to a disaster. This paper will describe the methodologies and practices used by RIT to deliver an open set of products typically within a twenty-four hour period from when they were initially collected. Response to the Haiti disaster can be broken down into four major sections: 1) data collection and logistics, 2) transmission of raw data from a remote location to a central processing and dissemination location, 3) rapid image processing of a massive amount of raw data, and 4) dissemination of processed data to global organizations utilizing it to provide the maximum benefit. Each section required it's own major effort to ensure the success of the overall mission. A discussion of each section will be provided along with an analysis of methods that could be implemented in future exercises to increase efficiency and effectiveness.

  11. Comparison of airborne multispectral and hyperspectral imagery for estimating grain sorghum yield

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Both multispectral and hyperspectral images are being used to monitor crop conditions and map yield variability, but limited research has been conducted to compare the differences between these two types of imagery for assessing crop growth and yields. The objective of this study was to compare airb...

  12. Processing Of Multispectral Data For Identification Of Rocks

    NASA Technical Reports Server (NTRS)

    Evans, Diane L.

    1990-01-01

    Linear discriminant analysis and supervised classification evaluated. Report discusses processing of multispectral remote-sensing imagery to identify kinds of sedimentary rocks by spectral signatures in geological and geographical contexts. Raw image data are spectra of picture elements in images of seven sedimentary rock units exposed on margin of Wind River Basin in Wyoming. Data acquired by Landsat Thematic Mapper (TM), Thermal Infrared Multispectral Scanner (TIMS), and NASA/JPL airborne synthetic-aperture radar (SAR).

  13. Combining multispectral and ancillary data in remote sensing using interval-valued probabilities

    NASA Technical Reports Server (NTRS)

    Kim, H.; Swain, P. H.

    1989-01-01

    This paper presents a method for classifying multisource data in remote sensing and geographic information systems using interval-valued probabilities. In this method, each data source is considered as an information source which provides a body of statistical evidence. In order to integrate information obtained from multiple data sources, the method adopts Dempster's rule for combining multiple bodies of evidence. Preliminary experiments have been undertaken to illustrate the use of the method in a supervised ground-cover classification on multispectral data combined with digital elevation data. They demonstrate the ability of the method in capturing information provided by inexact and incomplete evidence when there are not enough training samples to estimate statistical parameters.

  14. Radiative transfer in real atmospheres. [the implications for recognition processing of multispectral remote sensing data

    NASA Technical Reports Server (NTRS)

    Turner, R. E.

    1974-01-01

    The problem of multiple radiation scattering in an atmosphere characterized by various amounts of aerosol absorption and different particle size distributions was investigated. The visible part of the spectrum was emphasized, including the effect of ozone absorption. An atmosphere bounded by a nonhomogenous, Lambertian surface was also studied, along with the effect of background radiation on target in terms of various atmopheric and geometric conditions. Results of the investigation indicate that comtaminated atmospheres can change the radiation field by a considerable amount, and that the effect of non-uniform surface significantly alters the intrinsic radiation from a target element. The implications of these results for the recognition processing of multispectral remote sensing data is discussed.

  15. Single-Image Super Resolution for Multispectral Remote Sensing Data Using Convolutional Neural Networks

    NASA Astrophysics Data System (ADS)

    Liebel, L.; Körner, M.

    2016-06-01

    In optical remote sensing, spatial resolution of images is crucial for numerous applications. Space-borne systems are most likely to be affected by a lack of spatial resolution, due to their natural disadvantage of a large distance between the sensor and the sensed object. Thus, methods for single-image super resolution are desirable to exceed the limits of the sensor. Apart from assisting visual inspection of datasets, post-processing operations—e.g., segmentation or feature extraction—can benefit from detailed and distinguishable structures. In this paper, we show that recently introduced state-of-the-art approaches for single-image super resolution of conventional photographs, making use of deep learning techniques, such as convolutional neural networks (CNN), can successfully be applied to remote sensing data. With a huge amount of training data available, end-to-end learning is reasonably easy to apply and can achieve results unattainable using conventional handcrafted algorithms. We trained our CNN on a specifically designed, domain-specific dataset, in order to take into account the special characteristics of multispectral remote sensing data. This dataset consists of publicly available SENTINEL-2 images featuring 13 spectral bands, a ground resolution of up to 10m, and a high radiometric resolution and thus satisfying our requirements in terms of quality and quantity. In experiments, we obtained results superior compared to competing approaches trained on generic image sets, which failed to reasonably scale satellite images with a high radiometric resolution, as well as conventional interpolation methods.

  16. Development of an airborne remote sensing system for crop pest management: System integration and verification

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Remote sensing along with Global Positioning Systems, Geographic Information Systems, and variable rate technology has been developed, which scientists can implement to help farmers maximize the economic and environmental benefits of crop pest management through precision agriculture. Airborne remo...

  17. Analysis of remote sensing data collected for detection and mapping of oil spills: Reduction and analysis of multi-sensor airborne data of the NASA Wallops oil spill exercise of November 1978

    NASA Technical Reports Server (NTRS)

    1982-01-01

    Airborne, remotely sensed data of the NASA Wallops controlled oil spill were corrected, reduced and analysed. Sensor performance comparisons were made by registering data sets from different sensors, which were near-coincident in time and location. Multispectral scanner images were, in turn, overlayed with profiles of correlation between airborne and laboratory-acquired fluorosensor spectra of oil; oil-thickness contours derived (by NASA) from a scanning fluorosensor and also from a two-channel scanning microwave radiometer; and synthetic aperture radar X-HH images. Microwave scatterometer data were correlated with dual-channel (UV and TIR) line scanner images of the oil slick.

  18. A comparison between satellite and airborne multispectral data for the assessment of Mangrove areas in the eastern Caribbean

    SciTech Connect

    Green, E.P.; Edwards, A.J.; Mumby, P.J.

    1997-06-01

    Satellite (SPOT XS and Landsat TM) and airborne multispectral (CASI) imagery was acquired from the Turks and Caicos Islands, British West Indies. The descriptive resolution and accuracy of each image type is compared for two applications: mangrove habitat mapping and the measurement of mangrove canopy characteristics (leaf area index and canopy closure). Mangroves could be separated from non-mangrove vegetation to an accuracy of only 57% with SPOT XS data but better discrimination could be achieved with either Landsat TM or CASI (in both cases accuracy was >90%). CASI data permitted a more accurate classification of different mangrove habitats than was possible using Landsat TM. Nine mangrove habitats could be mapped to an accuracy of 85% with the high-resolution airborne data compared to 31% obtained with TM. A maximum of three mangrove habitats were separable with Landsat TM: the accuracy of this classification was 83%. Measurement of mangrove canopy characteristics is achieved more accurately with CASI than with either satellite sensor, but high costs probably make it a less cost-effective option. The cost-effectiveness of each sensor is discussed for each application.

  19. Data-intensive multispectral remote sensing of the nighttime Earth for environmental monitoring and emergency response

    NASA Astrophysics Data System (ADS)

    Zhizhin, M.; Poyda, A.; Velikhov, V.; Novikov, A.; Polyakov, A.

    2016-02-01

    All Most of the remote sensing applications rely on the daytime visible and infrared images of the Earth surface. Increase in the number of satellites, their spatial resolution as well as the number of the simultaneously observed spectral bands ensure a steady growth of the data volumes and computational complexity in the remote sensing sciences. Recent advance in the night time remote sensing is related to the enhanced sensitivity of the on-board instruments and to the unique opportunity to observe “pure” emitters in visible infrared spectra without contamination from solar heat and reflected light. A candidate set of the night-time emitters observable from the low-orbiting and geostationary satellites include steady state and temporal changes in the city and traffic electric lights, fishing boats, high-temperature industrial objects such as steel mills, oil cracking refineries and power plants, forest and agricultural fires, gas flares, volcanic eruptions and similar catastrophic events. Current satellite instruments can detect at night 10 times more of such objects compared to daytime. We will present a new data-intensive workflow of the night time remote sensing algorithms for map-reduce processing of visible and infrared images from the multispectral radiometers flown by the modern NOAA/NASA Suomi NPP and the USGS Landsat 8 satellites. Similar radiometers are installed on the new generation of the US geostationary GOES-R satellite to be launched in 2016. The new set of algorithms allows us to detect with confidence and track the abrupt changes and long-term trends in the energy of city lights, number of fishing boats, as well as the size, geometry, temperature of gas flares and to estimate monthly and early flared gas volumes by site or by country. For real-time analysis of the night time multispectral satellite images with global coverage we need gigabit network, petabyte data storage and parallel compute cluster with more than 20 nodes. To meet the

  20. First Airborne Laser Remote Measurements of Atmospheric Carbon Dioxide

    NASA Astrophysics Data System (ADS)

    Browell, E. V.; Dobbs, M. E.; Dobler, J.; Kooi, S.; Choi, Y.; Harrison, F. W.; Moore, B.; Zaccheo, T. S.

    2008-12-01

    A unique, multi-frequency, single-beam, laser absorption spectrometer (LAS) that operates at 1.57 μm has been developed for a future space-based mission to determine the global distribution of sources and sinks of atmospheric carbon dioxide (CO2). A prototype of the space-based LAS system was developed by ITT, and it has been successfully flight tested in five airborne campaigns conducted in different geographic regions over the last three years. Flight tests were conducted over Oklahoma, Michigan, New Hampshire, and Virginia under a wide range of atmospheric conditions. Remote LAS measurements were compared to high-quality in situ measurements obtained from instrumentation on the same aircraft on spirals under the ground track of the LAS. LAS flights were conducted over a wide range of land and water reflectances and in the presence of scattered clouds. An extensive data set of CO2 measurements has been obtained for evaluating the LAS performance. LAS CO2 measurements with a signal-to-noise in excess of 250 were obtained for a 1-s average over land and for a 10-s average over water. Absolute comparisons of CO2 remote and in situ measurements showed agreement over a range of altitudes to better than 2 percent. LAS oxygen (O2) measurements, which are needed to convert LAS CO2 density measurements to CO2 mixing ratios (XCO2), have been made in the 1.26-μm region in horizontal ground-based experiments and in initial flight tests. Details of flight test campaigns and measured versus modeled results are presented in this paper.

  1. Cloud Remote Sensing with Sideways-Looks : Theory and First Results Using Multispectral Thermal Imager Data

    SciTech Connect

    Davis, A. B.

    2002-01-01

    In operational remote sensing, the implicit model for cloud geometry is a homogeneous plane-parallel slab of infinite horizontal extent. Each pixel is indeed processed as if it exchanged no radiant energy whatsoever with its neighbors. The shortcomings of this conceptual model have been well documented in the specialized literature but rarely mitigated. The worst-case scenario is probably high-resolution imagery where dense isolated clouds are visible, often both bright (reflective) and dark (transmissive) sides being apparent from the same satellite viewing angle: the low transmitted radiance could conceivably be interpreted in plane-parallel theory as no cloud at all. An alternative to the plane-parallel cloud model is introduced here that has the same appeal of being analytically tractable, at least in the diffusion limit: the spherical cloud. This new geometrical paradigm is applied to radiances from cumulus clouds captured by DOE's Multispectral Thermal Imager (MTI). Estimates of isolated cloud opacities are a necessary first step in correcting radiances from surface targets that are visible in the midst of a broken-cloud field. This type of advanced atmospheric correction is badly needed in remote sensing applications such as nonproliferation detection were waiting for a cloud-free look in the indefinite future is not a viable option.

  2. A review and analysis of neural networks for classification of remotely sensed multispectral imagery

    NASA Technical Reports Server (NTRS)

    Paola, Justin D.; Schowengerdt, Robert A.

    1993-01-01

    A literature survey and analysis of the use of neural networks for the classification of remotely sensed multispectral imagery is presented. As part of a brief mathematical review, the backpropagation algorithm, which is the most common method of training multi-layer networks, is discussed with an emphasis on its application to pattern recognition. The analysis is divided into five aspects of neural network classification: (1) input data preprocessing, structure, and encoding; (2) output encoding and extraction of classes; (3) network architecture, (4) training algorithms; and (5) comparisons to conventional classifiers. The advantages of the neural network method over traditional classifiers are its non-parametric nature, arbitrary decision boundary capabilities, easy adaptation to different types of data and input structures, fuzzy output values that can enhance classification, and good generalization for use with multiple images. The disadvantages of the method are slow training time, inconsistent results due to random initial weights, and the requirement of obscure initialization values (e.g., learning rate and hidden layer size). Possible techniques for ameliorating these problems are discussed. It is concluded that, although the neural network method has several unique capabilities, it will become a useful tool in remote sensing only if it is made faster, more predictable, and easier to use.

  3. Sensor Correction and Radiometric Calibration of a 6-BAND Multispectral Imaging Sensor for Uav Remote Sensing

    NASA Astrophysics Data System (ADS)

    Kelcey, J.; Lucieer, A.

    2012-07-01

    The increased availability of unmanned aerial vehicles (UAVs) has resulted in their frequent adoption for a growing range of remote sensing tasks which include precision agriculture, vegetation surveying and fine-scale topographic mapping. The development and utilisation of UAV platforms requires broad technical skills covering the three major facets of remote sensing: data acquisition, data post-processing, and image analysis. In this study, UAV image data acquired by a miniature 6-band multispectral imaging sensor was corrected and calibrated using practical image-based data post-processing techniques. Data correction techniques included dark offset subtraction to reduce sensor noise, flat-field derived per-pixel look-up-tables to correct vignetting, and implementation of the Brown- Conrady model to correct lens distortion. Radiometric calibration was conducted with an image-based empirical line model using pseudo-invariant features (PIFs). Sensor corrections and radiometric calibration improve the quality of the data, aiding quantitative analysis and generating consistency with other calibrated datasets.

  4. Leica ADS40 Sensor for Coastal Multispectral Imaging

    NASA Technical Reports Server (NTRS)

    Craig, John C.

    2007-01-01

    The Leica ADS40 Sensor as it is used for coastal multispectral imaging is presented. The contents include: 1) Project Area Overview; 2) Leica ADS40 Sensor; 3) Focal Plate Arrangements; 4) Trichroid Filter; 5) Gradient Correction; 6) Image Acquisition; 7) Remote Sensing and ADS40; 8) Band comparisons of Satellite and Airborne Sensors; 9) Impervious Surface Extraction; and 10) Impervious Surface Details.

  5. Evaluating airborne multispectral digital video to differentiate giant Salvinia from other features in northeast Texas

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Giant salvinia is one of the world’s most noxious aquatic weeds. Researchers employed airborne digital video imagery and an unsupervised computer analysis to derive a map showing giant salvinia and other aquatic and terrestrial features within a study site located in northeast Texas. The map had a...

  6. From Pixels to Population Stress: Global Multispectral Remote Sensing for Vulnerable Communities

    NASA Astrophysics Data System (ADS)

    Prashad, L.; Kaplan, E.; Letouze, E.; Kirkpatrick, R.; Luengo-Oroz, M.; Christensen, P. R.

    2011-12-01

    The Arizona State University (ASU) School of Earth and Space Exploration's Mars Space Flight Facility (MSFF) and 100 Cities Project, in collaboration with the United Nations Global Pulse initiative are utilizing NASA multispectral satellite data to visualize and analyze socioeconomic characteristics and human activity in Uganda. The Global Pulse initiative is exploring how new kinds of real-time data and innovative technologies can be leveraged to detect early social impacts of slow-onset crisis and global shocks. Global Pulse is developing a framework for real-time monitoring, assembling an open-source toolkit for analyzing new kinds of data and establishing a global network of country-level "Pulse Labs" where governments, UN agencies, academia and the private sector learn together how to harness the new world of "big data" to protect the vulnerable with targeted and agile policy responses. The ASU MSFF and 100 Cities Project are coordinating with the Global Pulse team to utilize NASA remote sensing data in this effort. Human behavior and socioeconomic parameters have been successfully studied via proxy through remote sensing of the physical environment by measuring the growth of city boundaries and transportation networks, crop health, soil moisture, and slum development from visible and infrared imagery. The NASA/ NOAA image of Earth's "Lights at Night" is routinely used to estimate economic development and population density. There are many examples of the conventional uses of remote sensing in humanitarian-related projects including the Famine Early Warning System Network (FEWS NET) and the UN's operational satellite applications programme (UNOSAT), which provides remote sensing for humanitarian and disaster relief. Since the Global Pulse project is focusing on new, innovative uses of technology for early crisis detection, we are focusing on three non-conventional uses of satellite remote sensing to understand what role NASA multispectral satellites can play

  7. New, Flexible Applications with the Multi-Spectral Titan Airborne Lidar

    NASA Astrophysics Data System (ADS)

    Swirski, A.; LaRocque, D. P.; Shaker, A.; Smith, B.

    2015-12-01

    Traditional lidar designs have been restricted to using a single laser channel operating at one particular wavelength. Single-channel systems excel at collecting high-precision spatial (XYZ) data, with accuracies down to a few centimeters. However, target classification is difficult with spatial data alone, and single-wavelength systems are limited to the strengths and weaknesses of the wavelength they use. To resolve these limitations in lidar design, Teledyne Optech developed the Titan, the world's first multispectral lidar system, which uses three independent laser channels operating at 532, 1064, and 1550 nm. Since Titan collects 12 bit intensity returns for each wavelength separately, users can compare how strongly targets in the survey area reflect each wavelength. Materials such as soil, rock and foliage all reflect the wavelengths differently, enabling post-processing algorithms to identify the material of targets easily and automatically. Based on field tests in Canada, automated classification algorithms have combined this with elevation data to classify targets into six basic types with 78% accuracy. Even greater accuracy is possible with further algorithm enhancement and the use of an in-sensor passive imager such as a thermal, multispectral, CIR or RGB camera. Titan therefore presents an important new tool for applications such as land-cover classification and environmental modeling while maintaining lidar's traditional strengths: high 3D accuracy and day/night operation. Multispectral channels also enable a single lidar to handle both topographic and bathymetric surveying efficiently, which previously required separate specialized lidar systems operating at different wavelengths. On land, Titan can survey efficiently from 2000 m AGL with a 900 kHz PRF (300 kHz per channel), or up to 2500 m if only the infrared 1064 and 1550 nm channels are used. Over water, the 532 nm green channel penetrates water to collect seafloor returns while the infrared

  8. Use of Airborne Multi-Spectral Imagery in Pest Management Systems

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Scientists and researchers have been developing, integrating, and evaluating multiple strategies and technologies into a systems approach for management of field crop insect pests. Remote sensing along with Global Positioning Systems, Geographic Information Systems, and variable rate technology are...

  9. Assessing the application of an airborne intensified multispectral video camera to measure chlorophyll a in three Florida estuaries

    SciTech Connect

    Dierberg, F.E.; Zaitzeff, J.

    1997-08-01

    After absolute and spectral calibration, an airborne intensified, multispectral video camera was field tested for water quality assessments over three Florida estuaries (Tampa Bay, Indian River Lagoon, and the St. Lucie River Estuary). Univariate regression analysis of upwelling spectral energy vs. ground-truthed uncorrected chlorophyll a (Chl a) for each estuary yielded lower coefficients of determination (R{sup 2}) with increasing concentrations of Gelbstoff within an estuary. More predictive relationships were established by adding true color as a second independent variable in a bivariate linear regression model. These regressions successfully explained most of the variation in upwelling light energy (R{sup 2}=0.94, 0.82 and 0.74 for the Tampa Bay, Indian River Lagoon, and St. Lucie estuaries, respectively). Ratioed wavelength bands within the 625-710 nm range produced the highest correlations with ground-truthed uncorrected Chl a, and were similar to those reported as being the most predictive for Chl a in Tennessee reservoirs. However, the ratioed wavebands producing the best predictive algorithms for Chl a differed among the three estuaries due to the effects of varying concentrations of Gelbstoff on upwelling spectral signatures, which precluded combining the data into a common data set for analysis.

  10. Feasibility study for locating archaeological village sites by satellite remote sensing techniques. [multispectral photography of Alaska

    NASA Technical Reports Server (NTRS)

    Cook, J. P. (Principal Investigator); Stringer, W. J.

    1974-01-01

    The author has identified the following significant results. The objective is to determine the feasibility of detecting large Alaskan archaeological sites by satellite remote sensing techniques and mapping such sites. The approach used is to develop digital multispectral signatures of dominant surface features including vegetation, exposed soils and rock, hydrological patterns and known archaeological sites. ERTS-1 scenes are then printed out digitally in a map-like array with a letter reflecting the most appropriate classification representing each pixel. Preliminary signatures were developed and tested. It was determined that there was a need to tighten up the archaeological site signature by developing accurate signatures for all naturally-occurring vegetation and surface conditions in the vicinity of the test area. These second generation signatures have been tested by means of computer printouts and classified tape displays on the University of Alaska CDU-200 and by comparison with aerial photography. It has been concluded that the archaeological signatures now in use are as good as can be developed. Plans are to print out signatures for the entire test area and locate on topographic maps the likely locations of archaeological sites within the test area.

  11. A simple semi-automatic approach for land cover classification from multispectral remote sensing imagery.

    PubMed

    Jiang, Dong; Huang, Yaohuan; Zhuang, Dafang; Zhu, Yunqiang; Xu, Xinliang; Ren, Hongyan

    2012-01-01

    Land cover data represent a fundamental data source for various types of scientific research. The classification of land cover based on satellite data is a challenging task, and an efficient classification method is needed. In this study, an automatic scheme is proposed for the classification of land use using multispectral remote sensing images based on change detection and a semi-supervised classifier. The satellite image can be automatically classified using only the prior land cover map and existing images; therefore human involvement is reduced to a minimum, ensuring the operability of the method. The method was tested in the Qingpu District of Shanghai, China. Using Environment Satellite 1(HJ-1) images of 2009 with 30 m spatial resolution, the areas were classified into five main types of land cover based on previous land cover data and spectral features. The results agreed on validation of land cover maps well with a Kappa value of 0.79 and statistical area biases in proportion less than 6%. This study proposed a simple semi-automatic approach for land cover classification by using prior maps with satisfied accuracy, which integrated the accuracy of visual interpretation and performance of automatic classification methods. The method can be used for land cover mapping in areas lacking ground reference information or identifying rapid variation of land cover regions (such as rapid urbanization) with convenience. PMID:23049886

  12. A Simple Semi-Automatic Approach for Land Cover Classification from Multispectral Remote Sensing Imagery

    PubMed Central

    Jiang, Dong; Huang, Yaohuan; Zhuang, Dafang; Zhu, Yunqiang; Xu, Xinliang; Ren, Hongyan

    2012-01-01

    Land cover data represent a fundamental data source for various types of scientific research. The classification of land cover based on satellite data is a challenging task, and an efficient classification method is needed. In this study, an automatic scheme is proposed for the classification of land use using multispectral remote sensing images based on change detection and a semi-supervised classifier. The satellite image can be automatically classified using only the prior land cover map and existing images; therefore human involvement is reduced to a minimum, ensuring the operability of the method. The method was tested in the Qingpu District of Shanghai, China. Using Environment Satellite 1(HJ-1) images of 2009 with 30 m spatial resolution, the areas were classified into five main types of land cover based on previous land cover data and spectral features. The results agreed on validation of land cover maps well with a Kappa value of 0.79 and statistical area biases in proportion less than 6%. This study proposed a simple semi-automatic approach for land cover classification by using prior maps with satisfied accuracy, which integrated the accuracy of visual interpretation and performance of automatic classification methods. The method can be used for land cover mapping in areas lacking ground reference information or identifying rapid variation of land cover regions (such as rapid urbanization) with convenience. PMID:23049886

  13. Remote mapping of river bathymetry from publicly available multispectral image data

    NASA Astrophysics Data System (ADS)

    Legleiter, C. J.

    2011-12-01

    Remote sensing could facilitate efficient characterization of river systems for research and management purposes, provided that suitable image data are available and that the information derived therefrom is reliable. This study evaluated the utility of public domain multispectral images for estimating flow depths in a small stream and a larger gravel-bed river, using data acquired through a task-oriented consortium and the National Agricultural Imagery Program (NAIP). Field measurements were used to calibrate image-derived quantities to observed depths and to assess depth retrieval accuracy. A band ratio-based algorithm yielded coherent, hydraulically reasonable bathymetric maps for both field sites and three different types of image data. Applying a spatial filter reduced image noise and improved depth retrieval performance, with a strong calibration relationship (R2 = 0.68) and an observed (field-surveyed) vs. predicted (image-derived) R2 of 0.6 for tasked images of the smaller stream. The NAIP data were less useful in this environment due to geo-referencing errors and a coarser spatial resolution. On the larger river, NAIP-derived bathymetry was more accurate, with an observed vs. predicted R2 value of 0.64 for a compressed county mosaic easily accessible via the internet. Comparison of remotely sensed bathymetric maps with field surveys indicated that although the locations of pools were determined accurately, their full depth could not be detected due to limited sensor radiometric resolution. Although a number of other constraints also must be considered, such as the need for local calibration data, depth retrieval from publicly available image data is feasible under appropriate conditions.

  14. AIRBORNE, OPTICAL REMOTE SENSNG OF METHANE AND ETHANE FOR NATURAL GAS PIPELINE LEAK DETECTION

    SciTech Connect

    Jerry Myers

    2005-04-15

    Ophir Corporation was awarded a contract by the U. S. Department of Energy, National Energy Technology Laboratory under the Project Title ''Airborne, Optical Remote Sensing of Methane and Ethane for Natural Gas Pipeline Leak Detection'' on October 14, 2002. The scope of the work involved designing and developing an airborne, optical remote sensor capable of sensing methane and, if possible, ethane for the detection of natural gas pipeline leaks. Flight testing using a custom dual wavelength, high power fiber amplifier was initiated in February 2005. Ophir successfully demonstrated the airborne system, showing that it was capable of discerning small amounts of methane from a simulated pipeline leak. Leak rates as low as 150 standard cubic feet per hour (scf/h) were detected by the airborne sensor.

  15. Development of a Cost-Effective Airborne Remote Sensing System for Coastal Monitoring.

    PubMed

    Kim, Duk-jin; Jung, Jungkyo; Kang, Ki-mook; Kim, Seung Hee; Xu, Zhen; Hensley, Scott; Swan, Aaron; Duersch, Michael

    2015-01-01

    Coastal lands and nearshore marine areas are productive and rapidly changing places. However, these areas face many environmental challenges related to climate change and human-induced impacts. Space-borne remote sensing systems may be restricted in monitoring these areas because of their spatial and temporal resolutions. In situ measurements are also constrained from accessing the area and obtaining wide-coverage data. In these respects, airborne remote sensing sensors could be the most appropriate tools for monitoring these coastal areas. In this study, a cost-effective airborne remote sensing system with synthetic aperture radar and thermal infrared sensors was implemented to survey coastal areas. Calibration techniques and geophysical model algorithms were developed for the airborne system to observe the topography of intertidal flats, coastal sea surface current, sea surface temperature, and submarine groundwater discharge. PMID:26437413

  16. Development of a Cost-Effective Airborne Remote Sensing System for Coastal Monitoring

    PubMed Central

    Kim, Duk-jin; Jung, Jungkyo; Kang, Ki-mook; Kim, Seung Hee; Xu, Zhen; Hensley, Scott; Swan, Aaron; Duersch, Michael

    2015-01-01

    Coastal lands and nearshore marine areas are productive and rapidly changing places. However, these areas face many environmental challenges related to climate change and human-induced impacts. Space-borne remote sensing systems may be restricted in monitoring these areas because of their spatial and temporal resolutions. In situ measurements are also constrained from accessing the area and obtaining wide-coverage data. In these respects, airborne remote sensing sensors could be the most appropriate tools for monitoring these coastal areas. In this study, a cost-effective airborne remote sensing system with synthetic aperture radar and thermal infrared sensors was implemented to survey coastal areas. Calibration techniques and geophysical model algorithms were developed for the airborne system to observe the topography of intertidal flats, coastal sea surface current, sea surface temperature, and submarine groundwater discharge. PMID:26437413

  17. Commercial Applications Multispectral Sensor System

    NASA Technical Reports Server (NTRS)

    Birk, Ronald J.; Spiering, Bruce

    1993-01-01

    NASA's Office of Commercial Programs is funding a multispectral sensor system to be used in the development of remote sensing applications. The Airborne Terrestrial Applications Sensor (ATLAS) is designed to provide versatility in acquiring spectral and spatial information. The ATLAS system will be a test bed for the development of specifications for airborne and spaceborne remote sensing instrumentation for dedicated applications. This objective requires spectral coverage from the visible through thermal infrared wavelengths, variable spatial resolution from 2-25 meters; high geometric and geo-location accuracy; on-board radiometric calibration; digital recording; and optimized performance for minimized cost, size, and weight. ATLAS is scheduled to be available in 3rd quarter 1992 for acquisition of data for applications such as environmental monitoring, facilities management, geographic information systems data base development, and mineral exploration.

  18. Capturing the Green River -- Multispectral airborne videography to evaluate the environmental impacts of hydropower operations

    SciTech Connect

    Snider, M.A.; Hayse, J.W.; Hlohowskyj, I.; LaGory, K.E.

    1996-02-01

    The 500-mile long Green River is the largest tributary of the Colorado River. From its origin in the Wind River Range mountains of western Wyoming to its confluence with the Colorado River in southeastern Utah, the Green River is vital to the arid region through which it flows. Large portions of the area remain near-wilderness with the river providing a source of recreation in the form of fishing and rafting, irrigation for farming and ranching, and hydroelectric power. In the late 1950`s and early 1960`s hydroelectric facilities were built on the river. One of these, Flaming Gorge Dam, is located just south of the Utah-Wyoming border near the town of Dutch John, Utah. Hydropower operations result in hourly and daily fluctuations in the releases of water from the dam that alter the natural stream flow below the dam and affect natural resources in and along the river corridor. In the present study, the authors were interested in evaluating the potential impacts of hydropower operations at Flaming Gorge Dam on the downstream natural resources. Considering the size of the area affected by the daily pattern of water release at the dam as well as the difficult terrain and limited accessibility of many reaches of the river, evaluating these impacts using standard field study methods was virtually impossible. Instead an approach was developed that used multispectral aerial videography to determine changes in the affected parameters at different flows, hydrologic modeling to predict flow conditions for various hydropower operating scenarios, and ecological information on the biological resources of concern to assign impacts.

  19. Remote monitoring of soil moisture using airborne microwave radiometers

    NASA Technical Reports Server (NTRS)

    Kroll, C. L.

    1973-01-01

    The current status of microwave radiometry is provided. The fundamentals of the microwave radiometer are reviewed with particular reference to airborne operations, and the interpretative procedures normally used for the modeling of the apparent temperature are presented. Airborne microwave radiometer measurements were made over selected flight lines in Chickasha, Oklahoma and Weslaco, Texas. Extensive ground measurements of soil moisture were made in support of the aircraft mission over the two locations. In addition, laboratory determination of the complex permittivities of soil samples taken from the flight lines were made with varying moisture contents. The data were analyzed to determine the degree of correlation between measured apparent temperatures and soil moisture content.

  20. Multispectral Terrain Background Simulation Techniques For Use In Airborne Sensor Evaluation

    NASA Astrophysics Data System (ADS)

    Weinberg, Michael; Wohlers, Ronald; Conant, John; Powers, Edward

    1988-08-01

    A background simulation code developed at Aerodyne Research, Inc., called AERIE is designed to reflect the major sources of clutter that are of concern to staring and scanning sensors of the type being considered for various airborne threat warning (both aircraft and missiles) sensors. The code is a first principles model that could be used to produce a consistent image of the terrain for various spectral bands, i.e., provide the proper scene correlation both spectrally and spatially. The code utilizes both topographic and cultural features to model terrain, typically from DMA data, with a statistical overlay of the critical underlying surface properties (reflectance, emittance, and thermal factors) to simulate the resulting texture in the scene. Strong solar scattering from water surfaces is included with allowance for wind driven surface roughness. Clouds can be superimposed on the scene using physical cloud models and an analytical representation of the reflectivity obtained from scattering off spherical particles. The scene generator is augmented by collateral codes that allow for the generation of images at finer resolution. These codes provide interpolation of the basic DMA databases using fractal procedures that preserve the high frequency power spectral density behavior of the original scene. Scenes are presented illustrating variations in altitude, radiance, resolution, material, thermal factors, and emissivities. The basic models utilized for simulation of the various scene components and various "engineering level" approximations are incorporated to reduce the computational complexity of the simulation.

  1. Volcanic hot spot detection from optical multispectral remote sensing data using artificial neural networks

    NASA Astrophysics Data System (ADS)

    Piscini, Alessandro; Lombardo, Valerio

    2014-03-01

    This paper describes an application of artificial neural networks for the recognition of volcanic lava flow hot spots using remote sensing data. Satellite remote sensing is a very effective and safe way to monitor volcanic eruptions in order to safeguard the environment and the people affected by such natural hazards. Neural networks are an effective and well-established technique for the classification of satellite images. In addition, once well trained, they prove to be very fast in the application stage. In our study a back propagation neural network was used for the recognition of thermal anomalies affecting hot lava pixels. The network was trained using the three thermal channels of the Advanced Very High Resolution Radiometer (AVHRR) sensor as inputs and the corresponding values of heat flux, estimated using a two thermal component model, as reference outputs. As a case study the volcano Etna (Eastern Sicily, Italy) was chosen, and in particular the effusive eruption which took place during the month of 2006 July. The neural network was trained with a time-series of 15 images (12 nighttime images and 3 daytime images) and validated on three independent data sets of AVHRR images of the same eruption and on two relative to an eruption occurred the following month. While for both nighttime and daytime validation images the neural network identified the image pixels affected by hot lava with a 100 per cent success rate, for the daytime images also adjacent pixels were included, apparently not interested by lava flow. Despite these performance differences under different illumination conditions, the proposed method can be considered effective both in terms of classification accuracy and generalization capability. In particular our approach proved to be robust in the rejection of false positives, often corresponding to noisy or cloudy pixels, whose presence in multispectral images can often undermine the performance of traditional classification algorithms. Future

  2. Multisensor and Multispectral Approach in Documenting and Analyzing Liquefaction Hazard using Remote Sensing

    NASA Astrophysics Data System (ADS)

    Oommen, T.; Baise, L. G.; Gens, R.; Prakash, A.; Gupta, R. P.

    2008-12-01

    Seismic liquefaction is the loss of strength of soil due to shaking that leads to various ground failures such as lateral spreading, settlements, tilting, and sand boils. It is important to document these failures after earthquakes to advance our study of when and where liquefaction occurs. The current approach of mapping these failures by field investigation teams suffers due to the inaccessibility to some of the sites immediately after the event, short life of some of these failures, difficulties in mapping the aerial extent of the failure, incomplete coverage etc. After the 2001 Bhuj earthquake (India), researchers, using the Indian remote sensing satellite, illustrated that satellite remote sensing can provide a synoptic view of the terrain and offer unbiased estimates of liquefaction failures. However, a multisensor (data from different sensors onboard of the same or different satellites) and multispectral (data collected in different spectral regions) approach is needed to efficiently document liquefaction incidences and/or its potential of occurrence due to the possibility of a particular satellite being located inappropriately to image an area shortly after an earthquake. The use of SAR satellite imagery ensures the acquisition of data in all weather conditions at day and night as well as information complimentary to the optical data sets. In this study, we analyze the applicability of the various satellites (Landsat, RADARSAT, Terra-MISR, IRS-1C, IRS-1D) in mapping liquefaction failures after the 2001 Bhuj earthquake using Support Vector Data Description (SVDD). The SVDD is a kernel based nonparametric outlier detection algorithm inspired by the Support Vector Machines (SVMs), which is a new generation learning algorithm based on the statistical learning theory. We present the applicability of SVDD for unsupervised change-detection studies (i.e. to identify post-earthquake liquefaction failures). The liquefaction occurrences identified from the different

  3. PROGRAM ASPECT - FOR REMOTE SENSING OF AIRBORNE PLUMES

    EPA Science Inventory

    The SAFEGUARD program is a multi-sensor program for the detection and imaging of chemical plumes and vapors. The system is composed of an airborne sensor suite including an infrared line scanner and a high-speed fourier transform infrared spectrometer. Both systems are integrat...

  4. Airborne Remote Sensing of River Flow and Morphology

    NASA Astrophysics Data System (ADS)

    Zuckerman, S.; Anderson, S. P.; McLean, J.; Redford, R.

    2014-12-01

    River morphology, surface slope and flow are some of the fundamental measurements required for surface water monitoring and hydrodynamic research. This paper describes a method of combining bathymetric lidar with space-time processing of mid-wave infrared (MWIR) imagery to simultaneously measure bathymetry, currents and surface slope from an airborne platform. In May 2014, Areté installed a Pushbroom Imaging Lidar for Littoral Surveillance (PILLS) and a FLIR SC8000 MWIR imaging system sampling at 2 Hz in a small twin-engine aircraft. Data was collected over the lower Colorado River between Picacho Park and Parker. PILLS is a compact bathymetric lidar based on streak-tube sensor technology. It provides channel and bank topography and water surface elevation at 1 meter horizontal scales and 25 cm vertical accuracy. Surface currents are derived from the MWIR imagery by tracking surface features using a cross correlation algorithm. This approach enables the retrieval of currents along extended reaches at the forward speed of the aircraft with spatial resolutions down to 5 m with accuracy better than 10 cm/s. The fused airborne data captures current and depth variability on scales of meters over 10's of kilometers collected in just a few minutes. The airborne MWIR current retrievals are combined with the bathymetric lidar data to calculate river discharge which is then compared with real-time streamflow stations. The results highlight the potential for improving our understanding of complex river environments with simultaneous collections from multiple airborne sensors.

  5. Airborne Dial Remote Sensing of the Arctic Ozone Layer

    NASA Technical Reports Server (NTRS)

    Wirth, Martin; Renger, Wolfgang; Ehret, Gerhard

    1992-01-01

    A combined ozone and aerosol LIDAR was developed at the Institute of Physics of the Atmosphere at the DLR in Oberpfaffenhofen. It is an airborne version, that, based on the DIAL-principle, permits the recording of two-dimensional ozone profiles. This presentation will focus on the ozone-part; the aerosol subsection will be treated later.

  6. Remote sensing of soil moisture using airborne hyperspectral data

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The Institute for Technology Development (ITD) has developed an airborne hyperspectral sensor system that collects electromagnetic reflectance data of the terrain. The system consists of sensors for three different sections of the electromagnetic spectrum; the Ultra-Violet (UV), Visible/Near Infrare...

  7. Real-time remote detection and measurement for airborne imaging spectroscopy: a case study with methane

    NASA Astrophysics Data System (ADS)

    Thompson, D. R.; Leifer, I.; Bovensmann, H.; Eastwood, M.; Fladeland, M.; Frankenberg, C.; Gerilowski, K.; Green, R. O.; Kratwurst, S.; Krings, T.; Luna, B.; Thorpe, A. K.

    2015-06-01

    Localized anthropogenic sources of atmospheric CH4 are highly uncertain and temporally variable. Airborne remote measurement is an effective method to detect and quantify these emissions. In a campaign context, the science yield can be dramatically increased by real-time retrievals that allow operators to coordinate multiple measurements of the most active areas. This can improve science outcomes for both single- and multiple-platform missions. We describe a case study of the NASA/ESA CO2 and Methane Experiment (COMEX) campaign in California during June and August/September 2014. COMEX was a multi-platform campaign to measure CH4 plumes released from anthropogenic sources including oil and gas infrastructure. We discuss principles for real-time spectral signature detection and measurement, and report performance on the NASA Next Generation Airborne Visible Infrared Spectrometer (AVIRIS-NG). AVIRIS-NG successfully detected CH4 plumes in real-time at Gb s-1 data rates, characterizing fugitive releases in concert with other in situ and remote instruments. The teams used these real-time CH4 detections to coordinate measurements across multiple platforms, including airborne in situ, airborne non-imaging remote sensing, and ground-based in situ instruments. To our knowledge this is the first reported use of real-time trace gas signature detection in an airborne science campaign, and presages many future applications.

  8. Linking remotely sensed forage quality estimates from WorldView-2 multispectral data with cattle distribution in a savanna landscape

    NASA Astrophysics Data System (ADS)

    Zengeya, Fadzai M.; Mutanga, Onisimo; Murwira, Amon

    2013-04-01

    Remote sensing has recently been used to map forage quality for rangeland management. However, the validity of the remotely sensed forage quality can best be assessed when it connects well with the animal unit. In this study we used the new WorldView-2 multispectral imagery to estimate and map forage quality (nitrogen concentration) as a step to explain GPS based cattle distribution in a rangeland of Southeastern Zimbabwe. Nitrogen concentration was successfully estimated and mapped (Rcv2 = 0.66, relative error = 0.13%) using partial least squares regression (PLSR). The integration of GPS based cattle distribution patterns with forage quality in a GIS showed that cattle locations significantly clustered in areas of high forage quality. The results of this study suggest that new multispectral data with unique band settings such as WorldView-2 improves the estimation and mapping of forage quality in rangelands at landscape level. In addition, our results indicate that remotely sensed forage quality can be used to explain herbivore distribution, particularly cattle grazing patterns in rangelands.

  9. Road Asphalt Pavements Analyzed by Airborne Thermal Remote Sensing: Preliminary Results of the Venice Highway

    PubMed Central

    Pascucci, Simone; Bassani, Cristiana; Palombo, Angelo; Poscolieri, Maurizio; Cavalli, Rosa

    2008-01-01

    This paper describes a fast procedure for evaluating asphalt pavement surface defects using airborne emissivity data. To develop this procedure, we used airborne multispectral emissivity data covering an urban test area close to Venice (Italy).For this study, we first identify and select the roads' asphalt pavements on Multispectral Infrared Visible Imaging Spectrometer (MIVIS) imagery using a segmentation procedure. Next, since in asphalt pavements the surface defects are strictly related to the decrease of oily components that cause an increase of the abundance of surfacing limestone, the diagnostic absorption emissivity peak at 11.2μm of the limestone was used for retrieving from MIVIS emissivity data the areas exhibiting defects on asphalt pavements surface.The results showed that MIVIS emissivity allows establishing a threshold that points out those asphalt road sites on which a check for a maintenance intervention is required. Therefore, this technique can supply local government authorities an efficient, rapid and repeatable road mapping procedure providing the location of the asphalt pavements to be checked.

  10. Application of Multispectral and Hyperspectral Remote Sensing For Detection of Freshwater Harmful Algal Blooms

    NASA Astrophysics Data System (ADS)

    Kudela, R. M.; Accorsi, E.; Austerberry, D.; Palacios, S. L.

    2013-12-01

    Freshwater Cyanobacterial Harmful algal blooms (CHABs) represent a pressing and apparently increasing threat to both human and environmental health. In California, toxin producing blooms of several species, including Aphanizomenon, Microcystis, Lyngbya, and Anabaena are common; toxins from these blooms have been linked to impaired drinking water, domestic and wild animal deaths, and increasing evidence for toxin transfer to coastal marine environments, including the death of several California sea otters, a threatened marine species. California scientists and managers are under increasing pressure to identify and mitigate these potentially toxic blooms, but point-source measurements and grab samples have been less than effective. There is increasing awareness that these toxic events are both spatially widespread and ephememeral, leading to the need for better monitoring methods applicable to large spatial and temporal scales. Based on monitoring in several California water bodies, it appears that Aphanizomenon blooms frequently precede dangerous levels of toxins from Microcystis. We are exploring new detection methods for identifying CHABs and potentially distinguishing between blooms of the harmful cyanobacteria Aphanizomenon and Microcystis using remote sensing reflectance from a variety of airborne and satellite sensors. We suggest that Aphanizomenon blooms could potentially be used as an early warning of more highly toxic subsequent blooms, and that these methods, combined with better toxin monitoring, can lead to improved understanding and prediction of CHABs by pinpointing problematic watersheds.

  11. Remote sensing for non-renewable resources - Satellite and airborne multiband scanners for mineral exploration

    NASA Technical Reports Server (NTRS)

    Goetz, Alexander F. H.

    1986-01-01

    The application of remote sensing techniques to mineral exploration involves the use of both spatial (morphological) as well as spectral information. This paper is directed toward a discussion of the uses of spectral image information and emphasizes the newest airborne and spaceborne sensor developments involving imaging spectrometers.

  12. Remote Sensing of Leaf Area Index from Unmanned Airborne Vehicles (UAVs)

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Remote sensing with unmanned airborne vehicles (UAVs) has potential for rangeland management because: (1) pixels have very high spatial resolution, (2) cloud cover would not prevent acquisition during critical periods of plant growth, and (3) information is quickly delivered to the user. Winter whe...

  13. Remote Sensing Crop Leaf Area Index Using Unmanned Airborne Vehicles (UAV's)

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Remote sensing with unmanned airborne vehicles (UAVs) has more potential for within-season crop management than conventional satellite imagery because: (1) pixels have very high resolution, (2) cloud cover would not prevent acquisition during critical periods of growth, and (3) quick delivery of inf...

  14. Remote Sensing Leaf Area Index of Winter Wheat from Unmanned Airborne Vehicles (UAVs)

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Remote sensing with unmanned airborne vehicles (UAVs) has more potential for within-season crop management than conventional satellite imagery because: (1) pixels have very high resolution, (2) cloud cover would not prevent acquisition during critical periods of growth, and (3) quick delivery of inf...

  15. Use of remote sensing techniques for geological hazard surveys in vegetated urban regions. [multispectral imagery for lithological mapping

    NASA Technical Reports Server (NTRS)

    Stow, S. H.; Price, R. C.; Hoehner, F.; Wielchowsky, C.

    1976-01-01

    The feasibility of using aerial photography for lithologic differentiation in a heavily vegetated region is investigated using multispectral imagery obtained from LANDSAT satellite and aircraft-borne photography. Delineating and mapping of localized vegetal zones can be accomplished by the use of remote sensing because a difference in morphology and physiology results in different natural reflectances or signatures. An investigation was made to show that these local plant zones are affected by altitude, topography, weathering, and gullying; but are controlled by lithology. Therefore, maps outlining local plant zones were used as a basis for lithologic map construction.

  16. Airborne hyperspectral systems for solving remote sensing problems

    NASA Astrophysics Data System (ADS)

    Rodionov, I. D.; Rodionov, A. I.; Vedeshin, L. A.; Vinogradov, A. N.; Egorov, V. V.; Kalinin, A. P.

    2014-12-01

    A retrospective of airborne hyperspectrometer projects carried out in the ZAO Reagent Scientific Technical Center is presented. Hyperspectral devices developed during the period since the end of 1990s to the present day are described. The line of hyperspectrometers designed in recent times covers the ranges from ultraviolet (0.2 μm) to near infrared (1.0 μm). These devices can be mounted on airborne and automobile carriers, including small-size ones. By now, the developments of hyperspectral devices in ZAO Reagent have reached the finished state and have been prepared for serial production. Their technical characteristics permit one to speak of the creation of wide-range high-aperture ultraspectral high spatial resolution equipment with a possibility of real-time data processing on board.

  17. Mapping forest stand complexity for woodland caribou habitat assessment using multispectral airborne imagery

    NASA Astrophysics Data System (ADS)

    Zhang, W.; Hu, B.; Woods, M.

    2014-11-01

    The decline of the woodland caribou population is a result of their habitat loss. To conserve the habitat of the woodland caribou and protect it from extinction, it is critical to accurately characterize and monitor its habitat. Conventionally, products derived from low to medium spatial resolution remote sensing data, such as land cover classification and vegetation indices are used for wildlife habitat assessment. These products fail to provide information on the structure complexities of forest canopies which reflect important characteristics of caribou's habitats. Recent studies have employed the LiDAR system (Light Detection And Ranging) to directly retrieve the three dimensional forest attributes. Although promising results have been achieved, the acquisition cost of LiDAR data is very high. In this study, utilizing the very high spatial resolution imagery in characterizing the structural development the of forest canopies was exploited. A stand based image texture analysis was performed to predict forest succession stages. The results were demonstrated to be consistent with those derived from LiDAR data.

  18. Characterizing rangeland using multispectral remotely sensed data and multi-scale ecological units

    NASA Astrophysics Data System (ADS)

    Maynard, Catherine Cae Lee

    In this study ecological range unit (ERU) delineations combined with multispectral satellite data were examined to address the need for consistent, spatially accurate, and temporally current methods to inventory rangeland and estimate relative biomass productivity in the context of ecologically sensitive site parameters. ERUs, Landsat 7 ETM+ combined band values, and vegetation index data from 13 scenes acquired from June 2000 to August 2002 were used as predictive variables in linear regression estimates of total biomass using field data collected from 263 locations within 24 ecological range sites on 5 Montana ranches. GIS spatial data analysis techniques were applied to certified soils data themes and published landscape level ecological units to produce the ERU categories used to stratify the field data collection and image analysis, and as a method to test the use of an independent data set for addressing the known influence of soil and site variability on the spectral response of vegetation. ERU categories, in combination with the near and mid-infrared bands (Band 4, 0.75--0.90 mum; Band 7 2.09--2.35 mum), were significant independent variables, and in linear regression predictions collectively explained 66% of the variability in total biomass (p -value < 0.001), as compared to 52% explained by the combined bands alone, suggesting that ERU categories might be accounting for a component of soil variability. This report also introduces an efficient, remote sensing directed method for preliminary identification of locations within ERUs where indicators of soil and site stability or biotic integrity might be outside the established means. A comparison between sites with spectrally anomalous brightness, greenness, and wetness Tasseled Cap indices and selected measurements of spectrally sensitive rangeland ecological health indicators were used to develop a classification method for locating and screening rangeland categories. Pixels where site productivity and

  19. Investigation of atmospheric insect wing-beat frequencies and iridescence features using a multispectral kHz remote detection system

    NASA Astrophysics Data System (ADS)

    Gebru, Alem; Rohwer, Erich; Neethling, Pieter; Brydegaard, Mikkel

    2014-01-01

    Quantitative investigation of insect activity in their natural habitat is a challenging task for entomologists. It is difficult to address questions such as flight direction, predation strength, and overall activities using the current techniques such as traps and sweep nets. A multispectral kHz remote detection system using sunlight as an illumination source is presented. We explore the possibilities of remote optical classification of insects based on their wing-beat frequencies and iridescence features. It is shown that the wing-beat frequency of the fast insect events can be resolved by implementing high-sampling frequency. The iridescence features generated from the change of color in two channels (visible and near-infrared) during wing-beat cycle are presented. We show that the shape of the wing-beat trajectory is different for different insects. The flight direction of an atmospheric insect is also determined using a silicon quadrant detector.

  20. Multispectral airborne imagery in the field reveals genetic determinisms of morphological and transpiration traits of an apple tree hybrid population in response to water deficit.

    PubMed

    Virlet, Nicolas; Costes, Evelyne; Martinez, Sébastien; Kelner, Jean-Jacques; Regnard, Jean-Luc

    2015-09-01

    Genetic studies of response to water deficit in adult trees are limited by low throughput of the usual phenotyping methods in the field. Here, we aimed at overcoming this bottleneck, applying a new methodology using airborne multispectral imagery and in planta measurements to compare a high number of individuals.An apple tree population, grafted on the same rootstock, was submitted to contrasting summer water regimes over two years. Aerial images acquired in visible, near- and thermal-infrared at three dates each year allowed calculation of vegetation and water stress indices. Tree vigour and fruit production were also assessed. Linear mixed models were built accounting for date and year effects on several variables and including the differential response of genotypes between control and drought conditions.Broad-sense heritability of most variables was high and 18 quantitative trait loci (QTLs) independent of the dates were detected on nine linkage groups of the consensus apple genetic map. For vegetation and stress indices, QTLs were related to the means, the intra-crown heterogeneity, and differences induced by water regimes. Most QTLs explained 15-20% of variance.Airborne multispectral imaging proved relevant to acquire simultaneous information on a whole tree population and to decipher genetic determinisms involved in response to water deficit. PMID:26208644

  1. Multispectral airborne imagery in the field reveals genetic determinisms of morphological and transpiration traits of an apple tree hybrid population in response to water deficit

    PubMed Central

    Virlet, Nicolas; Costes, Evelyne; Martinez, Sébastien; Kelner, Jean-Jacques; Regnard, Jean-Luc

    2015-01-01

    Genetic studies of response to water deficit in adult trees are limited by low throughput of the usual phenotyping methods in the field. Here, we aimed at overcoming this bottleneck, applying a new methodology using airborne multispectral imagery and in planta measurements to compare a high number of individuals. An apple tree population, grafted on the same rootstock, was submitted to contrasting summer water regimes over two years. Aerial images acquired in visible, near- and thermal-infrared at three dates each year allowed calculation of vegetation and water stress indices. Tree vigour and fruit production were also assessed. Linear mixed models were built accounting for date and year effects on several variables and including the differential response of genotypes between control and drought conditions. Broad-sense heritability of most variables was high and 18 quantitative trait loci (QTLs) independent of the dates were detected on nine linkage groups of the consensus apple genetic map. For vegetation and stress indices, QTLs were related to the means, the intra-crown heterogeneity, and differences induced by water regimes. Most QTLs explained 15−20% of variance. Airborne multispectral imaging proved relevant to acquire simultaneous information on a whole tree population and to decipher genetic determinisms involved in response to water deficit. PMID:26208644

  2. Analysis of Vegetation Within A Semi-Arid Urban Environment Using High Spatial Resolution Airborne Thermal Infrared Remote Sensing Data

    NASA Technical Reports Server (NTRS)

    Quattrochi, Dale A.; Ridd, Merrill K.

    1998-01-01

    High spatial resolution (5 m) remote sensing data obtained using the airborne Thermal Infrared Multispectral Scanner (TIMS) sensor for daytime and nighttime have been used to measure thermal energy responses for 2 broad classes and 10 subclasses of vegetation typical of the Salt Lake City, Utah urban landscape. Polygons representing discrete areas corresponding to the 10 subclasses of vegetation types have been delineated from the remote sensing data and are used for analysis of upwelling thermal energy for day, night, and the change in response between day and night or flux, as measured by the TIMS. These data have been used to produce three-dimensional graphs of energy responses in W/ sq m for day, night, and flux, for each urban vegetation land cover as measured by each of the six channels of the TIMS sensor. Analysis of these graphs provides a unique perspective for both viewing and understanding thermal responses, as recorded by the TIMS, for selected vegetation types common to Salt Lake City. A descriptive interpretation is given for each of the day, night, and flux graphs along with an analysis of what the patterns mean in reference to the thermal properties of the vegetation types surveyed in this study. From analyses of these graphs, it is apparent that thermal responses for vegetation can be highly varied as a function of the biophysical properties of the vegetation itself, as well as other factors. Moreover, it is also seen where vegetation, particularly trees, has a significant influence on damping or mitigating the amount of thermal radiation upwelling into the atmosphere across the Salt Lake City urban landscape. Published by Elsevier Science Ltd.

  3. Progress in the development of airborne remote sensing instrumentation for the National Ecological Observatory Network

    NASA Astrophysics Data System (ADS)

    Kampe, Thomas U.; McCorkel, Joel; Hamlin, Louise; Green, Robert O.; Krause, Keith S.; Johnson, Brian R.

    2011-09-01

    The National Ecological Observatory Network (NEON) is a planned facility of the National Science Foundation with the mission to enable understanding and forecasting of the impacts of climate change, land use change and invasive species on continental-scale ecology. Airborne remote sensing plays a critical role by providing measurements at the scale of individual shrubs and larger plants over hundreds of square kilometers. The NEON Airborne Observation Platform is designed to bridge scales from organism and stand scales, as captured by plot and tower observations, to the scale of satellite based remote sensing. Fused airborne spectroscopy and waveform LiDAR is used to quantify vegetation composition and structure. Panchromatic photography at better than 30 cm resolution will retrieve fine-scale information on land use, roads, impervious surfaces, and built structures. NEON will build three airborne systems to allow for regular coverage of NEON sites and the capacity to respond to investigator requests for specific projects. The system design achieves a balance between performance and development cost and risk, taking full advantage of existing commercial airborne LiDAR and camera components. To reduce risk during NEON construction, an imaging spectrometer design verification unit is being developed at the Jet Propulsion Laboratory to demonstrate that operational and performance requirements can be met. As part of this effort, NEON is also focusing on science algorithm development, computing hardware prototyping and early airborne test flights with similar technologies. This paper presents an overview of the development status of the NEON airborne instrumentation in the context of the NEON mission.

  4. Estimating Crop Residue Distribution Using Airborne and Satellite Remote Sensing

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Crop residue management and reduced tillage are commonly accepted best management practices that improve soil quality through the sequestration of soil organic carbon. A major goal of this study was to evaluate remote sensing data for rapid quantification of conservation tillage at the field and wa...

  5. Airborne Remote Sensing (ARS) for Agricultural Research and Commercialization Applications

    NASA Technical Reports Server (NTRS)

    Narayanan, Ram; Bowen, Brent D.; Nickerson, Jocelyn S.

    2002-01-01

    Tremendous advances in remote sensing technology and computing power over the last few decades are now providing scientists with the opportunity to investigate, measure, and model environmental patterns and processes with increasing confidence. Such advances are being pursued by the Nebraska Remote Sensing Facility, which consists of approximately 30 faculty members and is very competitive with other institutions in the depth of the work that is accomplished. The development of this facility targeted at applications, commercialization, and education programs in the area of precision agriculture provides a unique opportunity. This critical area is within the scope of NASA goals and objectives of NASA s Applications, Technology Transfer, Commercialization, and Education Division and the Earth Science Enterprise. This innovative integration of Aerospace (Aeronautics) Technology Enterprise applications with other NASA enterprises serves as a model of cross-enterprise transfer of science with specific commercial applications.

  6. Real-time remote detection and measurement for airborne imaging spectroscopy: a case study with methane

    NASA Astrophysics Data System (ADS)

    Thompson, D. R.; Leifer, I.; Bovensmann, H.; Eastwood, M.; Fladeland, M.; Frankenberg, C.; Gerilowski, K.; Green, R. O.; Kratwurst, S.; Krings, T.; Luna, B.; Thorpe, A. K.

    2015-10-01

    Localized anthropogenic sources of atmospheric CH4 are highly uncertain and temporally variable. Airborne remote measurement is an effective method to detect and quantify these emissions. In a campaign context, the science yield can be dramatically increased by real-time retrievals that allow operators to coordinate multiple measurements of the most active areas. This can improve science outcomes for both single- and multiple-platform missions. We describe a case study of the NASA/ESA CO2 and MEthane eXperiment (COMEX) campaign in California during June and August/September 2014. COMEX was a multi-platform campaign to measure CH4 plumes released from anthropogenic sources including oil and gas infrastructure. We discuss principles for real-time spectral signature detection and measurement, and report performance on the NASA Next Generation Airborne Visible Infrared Spectrometer (AVIRIS-NG). AVIRIS-NG successfully detected CH4 plumes in real-time at Gb s-1 data rates, characterizing fugitive releases in concert with other in situ and remote instruments. The teams used these real-time CH4 detections to coordinate measurements across multiple platforms, including airborne in situ, airborne non-imaging remote sensing, and ground-based in situ instruments. To our knowledge this is the first reported use of real-time trace-gas signature detection in an airborne science campaign, and presages many future applications. Post-analysis demonstrates matched filter methods providing noise-equivalent (1σ) detection sensitivity for 1.0 % CH4 column enhancements equal to 141 ppm m.

  7. ET mapping with METRIC algorithm using airborne high resolution multispectral remote sensing imagery

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Routine and accurate estimates of spatially distributed evapotranspiration (ET) are essential for managing water resources particularly in irrigated regions such as the U.S. Southern High Plains. For instance, ET maps would assist in the improvement of the Ogallala Aquifer ground water management. M...

  8. Assessment of soybean injury from glyphosate using airborne multispectral remote sensing

    Technology Transfer Automated Retrieval System (TEKTRAN)

    BACKGROUND: Glyphosate drift onto off-target sensitive crops can reduce growth and yield, and is of great concern to growers and pesticide applicators. Detection of herbicide injury using biological responses is tedious, so more convenient and rapid detection methods are needed. The objective of thi...

  9. Airborne remote sensing for geology and the environment: Present and future. Bulletin

    SciTech Connect

    Watson, K.; Knepper, D.H.

    1994-12-31

    In 1988, a group of leading experts from government, academia, and industry attended a workshop on airborne remote sensing sponsored by the U.S. Geological Survey (USGS) and hosted by the Branch of Geophysics. The report has arranged the six resulting working-group reports under two main headings: (1) Geologic Remote Sensing, for the reports on geologic mapping, mineral resoures, and fossil fuels and geothermal resources; and (2) Environmental Remote Sensing, for the reports on environmental geology, geologic hazards, and water resources. The intent of the workshop was to provide an evaluation of demonstrated capabilities, their direct extensions, and possible future applications, and this was the organizational format used for the geologic remote sensing reports. A final section examines future advances and limitations in the field.

  10. Flight Tests of the DELICAT Airborne LIDAR System for Remote Clear Air Turbulence Detection

    NASA Astrophysics Data System (ADS)

    Vrancken, Patrick; Wirth, Martin; Ehret, Gerhard; Witschas, Benjamin; Veerman, Henk; Tump, Robert; Barny, Hervé; Rondeau, Philippe; Dolfi-Bouteyre, Agnès; Lombard, Laurent

    2016-06-01

    An important aeronautics application of lidar is the airborne remote detection of Clear Air Turbulence which cannot be performed with onboard radar. We report on a DLR-developed lidar system for the remote detection of such turbulent areas in the flight path of an aircraft. The lidar, consisting of a high-power UV laser transmitter and a direct detection system, was installed on a Dutch research aircraft. Flight tests executed in 2013 demonstrated the performance of the lidar system to detect local subtle variations in the molecular backscatter coefficient indicating the turbulence some 10 to 15 km ahead.

  11. Airborne remote sensors applied to engineering geology and civil works design investigations

    NASA Technical Reports Server (NTRS)

    Gelnett, R. H.

    1975-01-01

    The usefulness of various airborne remote sensing systems in the detection and identification of regional and specific geologic structural features that may affect the design and location of engineering structures on major civil works projects is evaluated. The Butler Valley Dam and Blue Lake Project in northern California was selected as a demonstration site. Findings derived from the interpretation of various kinds of imagery used are given.

  12. A New Airborne Lidar for Remote Sensing of Canopy Fluorescence and Vertical Profile

    NASA Astrophysics Data System (ADS)

    Ounis, A.; Bach, J.; Mahjoub, A.; Daumard, F.; Moya, I.; Goulas, Y.

    2016-06-01

    We report the development of a new lidar system for airborne remote sensing of chlorophyll fluorescence (ChlF) and vertical profile of canopies. By combining laserinduced fluorescence (LIF), sun-induced fluorescence (SIF) and canopy height distribution, the new instrument will low the simultaneous assessment of gross primary production (GPP), photosynthesis efficiency and above ground carbon stocks. Technical issues of the lidar development are discussed and expected performances are presented.

  13. An airborne four-camera imaging system for agricultural applications

    Technology Transfer Automated Retrieval System (TEKTRAN)

    This paper describes the design and testing of an airborne multispectral digital imaging system for remote sensing applications. The system consists of four high resolution charge coupled device (CCD) digital cameras and a ruggedized PC equipped with a frame grabber and image acquisition software. T...

  14. Multispectral Photography

    NASA Technical Reports Server (NTRS)

    1982-01-01

    Model II Multispectral Camera is an advanced aerial camera that provides optimum enhancement of a scene by recording spectral signatures of ground objects only in narrow, preselected bands of the electromagnetic spectrum. Its photos have applications in such areas as agriculture, forestry, water pollution investigations, soil analysis, geologic exploration, water depth studies and camouflage detection. The target scene is simultaneously photographed in four separate spectral bands. Using a multispectral viewer, such as their Model 75 Spectral Data creates a color image from the black and white positives taken by the camera. With this optical image analysis unit, all four bands are superimposed in accurate registration and illuminated with combinations of blue green, red, and white light. Best color combination for displaying the target object is selected and printed. Spectral Data Corporation produces several types of remote sensing equipment and also provides aerial survey, image processing and analysis and number of other remote sensing services.

  15. AIRBORNE, OPTICAL REMOTE SENSING OF METHANE AND ETHANE FOR NATURAL GAS PIPELINE LEAK DETECTION

    SciTech Connect

    Jerry Myers

    2003-11-12

    Ophir Corporation was awarded a contract by the U. S. Department of Energy, National Energy Technology Laboratory under the Project Title ''Airborne, Optical Remote Sensing of Methane and Ethane for Natural Gas Pipeline Leak Detection'' on October 14, 2002. This second six-month technical report summarizes the progress made towards defining, designing, and developing the hardware and software segments of the airborne, optical remote methane and ethane sensor. The most challenging task to date has been to identify a vendor capable of designing and developing a light source with the appropriate output wavelength and power. This report will document the work that has been done to identify design requirements, and potential vendors for the light source. Significant progress has also been made in characterizing the amount of light return available from a remote target at various distances from the light source. A great deal of time has been spent conducting laboratory and long-optical path target reflectance measurements. This is important since it helps to establish the overall optical output requirements for the sensor. It also reduces the relative uncertainty and risk associated with developing a custom light source. The data gathered from the optical path testing has been translated to the airborne transceiver design in such areas as: fiber coupling, optical detector selection, gas filters, and software analysis. Ophir will next, summarize the design progress of the transceiver hardware and software development. Finally, Ophir will discuss remaining project issues that may impact the success of the project.

  16. Stratigraphic correlation by integrating photostratigraphy and remote sensing multispectral data: An example from Jurassic-Eocene strata, Northern Somalia

    SciTech Connect

    Sgavetti, M.; Ferrari, M.C.; Chiari, R.

    1995-11-01

    Integrated analyses of aerial photographs and multispectral remote sensing images were used for stratigraphic correlation in mainly carbonate and evaporitic rocks. These rocks crop out in an area of northern Somalia characterized by an arid climate. By the aerial photo analysis, we recognized photostratigraphic logs and stratal patterns and established correlations based on the tracing of physical surfaces with chronostratigraphic significance, such as photohorizons and photostratigraphic discontinuities. A limited number of field sections provided the lithological interpretation of the packages of strata delineated in aerial photos. By satellite multispectral (Landsat Thematic Mapper{trademark}) data analysis we identified image facies that represent packages of strata with different lithological characteristics. To interpret the image facies, we compared the responses in the thematic mapper (TM) bands with the laboratory spectroscopic properties of rock samples from the study area, and interpreted the absorption features by petrographic analysis. The Mesozoic and Tertiary strata analyzed herein are part of several formations deposited on a passive margin preceding the Oligocene-Miocene Gulf of Aden rifting and initial drifting. Following this approach, a number of stratigraphic units were recognized and mapped on aerial photos, and a framework of photostratigraphic correlation surfaces was delineated over significantly wide areas. These surfaces approximate time surfaces and are traced both within and across the lithostratigraphic units, improving existing maps. This method represents a mapping tool preliminary to more detailed field work, and is particularly useful in areas of difficult access.

  17. Remote sensing of sediment and chlorophyll with the test-bed aircraft multispectral scanner

    NASA Technical Reports Server (NTRS)

    Bowker, D. E.; Hardesty, C. A.; Jobson, D. J.

    1983-01-01

    An instrument known as the test-bed aircraft multispectral scanner (TBAMS) was used in a research flight over the entrance to the Chesapeake Bay. Upwelled radiances from the TBAMS data were correlated with the water parameters, particularly sediment and chlorophyll a. Several algorithms were demonstrated for monitoring sediment and chlorophyll, with a three-band ratio being the best. The primary advantage of the three-band ratio was found to be its apparent insensitivity to atmospheric and Sun-angle variations.

  18. Sensitivity of Multiangle, Multispectral Polarimetric Remote Sensing Over Open Oceans to Water-Leaving Radiance: Analyses of RSP Data Acquired During the MILAGRO Campaign

    NASA Technical Reports Server (NTRS)

    Chowdhary, Jacek; Cairns, Brian; Waquet, Fabien; Knobelspiesse, Kirk; Ottaviani, Matteo; Redemann, Jens; Travis, Larry; Mishchenko, Michael

    2012-01-01

    For remote sensing of aerosol over the ocean, there is a contribution from light scattered underwater. The brightness and spectrum of this light depends on the biomass content of the ocean, such that variations in the color of the ocean can be observed even from space. Rayleigh scattering by pure sea water, and Rayleigh-Gans type scattering by plankton, causes this light to be polarized with a distinctive angular distribution. To study the contribution of this underwater light polarization to multiangle, multispectral observations of polarized reflectance over ocean, we previously developed a hydrosol model for use in underwater light scattering computations that produces realistic variations of the ocean color and the underwater light polarization signature of pure sea water. In this work we review this hydrosol model, include a correction for the spectrum of the particulate scattering coefficient and backscattering efficiency, and discuss its sensitivity to variations in colored dissolved organic matter (CDOM) and in the scattering function of marine particulates. We then apply this model to measurements of total and polarized reflectance that were acquired over open ocean during the MILAGRO field campaign by the airborne Research Scanning Polarimeter (RSP). Analyses show that our hydrosol model faithfully reproduces the water-leaving contributions to RSP reflectance, and that the sensitivity of these contributions to Chlorophyll a concentration [Chl] in the ocean varies with the azimuth, height, and wavelength of observations. We also show that the impact of variations in CDOM on the polarized reflectance observed by the RSP at low altitude is comparable to or much less than the standard error of this reflectance whereas their effects in total reflectance may be substantial (i.e. up to >30%). Finally, we extend our study of polarized reflectance variations with [Chl] and CDOM to include results for simulated spaceborne observations.

  19. Assessment of Superflux relative to remote sensing. [airborne remote sensing of the Chesapeake Bay plume and shelf regions

    NASA Technical Reports Server (NTRS)

    Campbell, J. W.

    1981-01-01

    The state-of-the-art advancements in remote sensor technology due to the Superflux program are examined. Three major individual sensor technologies benefitted from the program: laser fluorosensors, optical-range scanners, and passive microwave sensors. Under Superflux, convincing evidence was obtained that the airborne oceanographic lidar fluorosensor can map chlorophyll, i.e., is linear, over a wide range from less than 0.5 to 5.0 mg/cu m. The lidar oceanographic probe dual-excitation concept for addressing phytoplankton color group composition was also demonstrated convincingly. Algorithm development, real time capabilities, and multisensor integration are also addressed.

  20. Remote quantitative analysis of minerals based on multispectral line-calibrated laser-induced breakdown spectroscopy (LIBS).

    PubMed

    Wan, Xiong; Wang, Peng

    2014-01-01

    Laser-induced breakdown spectroscopy (LIBS) is a feasible remote sensing technique used for mineral analysis in some unapproachable places where in situ probing is needed, such as analysis of radioactive elements in a nuclear leak or the detection of elemental compositions and contents of minerals on planetary and lunar surfaces. Here a compact custom 15 m focus optical component, combining a six times beam expander with a telescope, has been built, with which the laser beam of a 1064 nm Nd ; YAG laser is focused on remote minerals. The excited LIBS signals that reveal the elemental compositions of minerals are collected by another compact single lens-based signal acquisition system. In our remote LIBS investigations, the LIBS spectra of an unknown ore have been detected, from which the metal compositions are obtained. In addition, a multi-spectral line calibration (MSLC) method is proposed for the quantitative analysis of elements. The feasibility of the MSLC and its superiority over a single-wavelength determination have been confirmed by comparison with traditional chemical analysis of the copper content in the ore. PMID:25239065

  1. Utilizing hyperspectral and multispectral remote sensing and geographic information systems to identify and differentiate weed and crop species

    NASA Astrophysics Data System (ADS)

    Barber, Lon Thomas

    2004-12-01

    Weed species are not evenly distributed across a field; thus, if remote sensing imagery could be utilized as a tool for locating and identifying these patches, herbicides could be applied according to species and spatial distribution. In order to utilize site-specific technology to apply herbicides, the spatial variability of weed populations within a field must be known. Research was conducted to determine if remote sensing could be utilized as a tool for identifying and separating weed species from cotton and corn. Additionally geographic information systems and herbicide decision aids were tested to determine if weed population mapping could result in accurate site-specific and multiple product herbicide applications. Species separation based on hyperspectral data was successful in differentiating cotton and corn from weed species. By identifying the best spectral bands and utilizing vegetation indices, species classification ranged from 67 to 99% for cotton, 47 to 98% for corn and 95 to 98% for weed species. Species identification increased with data accumulation later in the growing season due to increased leaf area and biomass. Results indicate that weed and crop separation is possible when the best spectral bands are identified and utilized in conjunction with vegetation indices. Multispectral imagery was also tested for species identification and was found to produce lower classification accuracies than hyperspectral data. Cotton and corn were classified 50 to 100%; however, weed species classification was poor (<50%) with multispectral imagery. Poor classification was observed because only 4 regions of the electromagnetic spectrum were utilized. Multispectral identification would likely improve if the best spectral bands identified in the hyperspectral research were utilized in sensors for aerial imagery. Weed species and density information was mapped utilizing a geographic information system. Site-specific and broadcast herbicide applications were made

  2. Russian multispectral-hyperspectral airborne scanner for geological and environmental investigations - {open_quotes}Vesuvius-EC{close_quotes}

    SciTech Connect

    Yassinsky, G.I.; Shilin, B.V.

    1996-07-01

    Small variations of spectral characteristics in 0,3-14 microns band are of great significance in geological and environmental investigations. Multipurpose multispectral digital scanner with narrow field of view, high spectral resolution and radiometric calibration designed in Russia. Changeable modules permit to obtain parameters of the device for practical using.

  3. Remote sensing for precision agriculture: Within-field spatial variability analysis and mapping with aerial digital multispectral images

    NASA Astrophysics Data System (ADS)

    Gopalapillai, Sreekala

    2000-10-01

    Advances in remote sensing technology and biological sensors provided the motivation for this study on the applications of aerial multispectral remote sensing in precision agriculture. The feasibility of using high-resolution multispectral remote sensing for precision farming applications such as soil type delineation, identification of crop nitrogen levels, and modeling and mapping of weed density distribution and yield potential within a crop field was explored in this study. Some of the issues such as image calibration for variable lighting conditions and soil background influence were also addressed. Intensity normalization and band ratio methods were found to be adequate image calibration methods to compensate for variable illumination and soil background influence. Several within-field variability factors such as growth stage, field conditions, nutrient availability, crop cultivar, and plant population were found to be dominant in different periods. Unsupervised clustering of color infrared (CIR) image of a field soil was able to identify soil mapping units with an average accuracy of 76%. Spectral reflectance from a crop field was highly correlated to the chlorophyll reading. A regression model developed to predict nitrogen stress in corn identified nitrogen-stressed areas from nitrogen-sufficient areas with a high accuracy (R2 = 0.93). Weed density was highly correlated to the spectral reflectance from a field. One month after planting was found to be a good time to map spatial weed density. The optimum range of resolution for weed mapping was 4 m to 4.5 m for the remote sensing system and the experimental field used in this study. Analysis of spatial yield with respect to spectral reflectance showed that the visible and NIR reflectance were negatively correlated to yield and crop population in heavily weed-infested areas. The yield potential was highly correlated to image indices, especially to normalized brightness. The ANN model developed for one of the

  4. MULTISPECTRAL REMOTE SENSING OF CARBONATE ROCKS IN THE CONFUSION RANGE, UTAH.

    USGS Publications Warehouse

    Crowley, James K.

    1984-01-01

    Multispectral imagery recorded by the NASA/Bendix 24-channel aircraft scanner over the Confusion Range, Utah, proved to be extremely sensitive to lithologic variations in exposed carbonate rocks. Major carbonate units within a 16-km**2 study area were readily distinguished, and some aspects of their structure and stratigraphy could be inferred from image spectral signatures. Spectral data channels centered at 1. 6 and 2. 2 mu m accounted for much of the data sensitivity to lithologic differences. Rock texture, organic matter content, and weathering expression were important lithologic factors producing spectral variation.

  5. AIRBORNE, OPTICAL REMOTE SENSING OF METHANE AND ETHANE FOR NATURAL GAS PIPLINE LEAK DETECTION

    SciTech Connect

    Jerry Myers

    2004-05-12

    Ophir Corporation was awarded a contract by the U. S. Department of Energy, National Energy Technology Laboratory under the Project Title ''Airborne, Optical Remote Sensing of Methane and Ethane for Natural Gas Pipeline Leak Detection'' on October 14, 2002. The third six-month technical report contains a summary of the progress made towards finalizing the design and assembling the airborne, remote methane and ethane sensor. The vendor has been chosen and is on contract to develop the light source with the appropriate linewidth and spectral shape to best utilize the Ophir gas correlation software. Ophir has expanded upon the target reflectance testing begun in the previous performance period by replacing the experimental receiving optics with the proposed airborne large aperture telescope, which is theoretically capable of capturing many times more signal return. The data gathered from these tests has shown the importance of optimizing the fiber optic receiving fiber to the receiving optic and has helped Ophir to optimize the design of the gas cells and narrowband optical filters. Finally, Ophir will discuss remaining project issues that may impact the success of the project.

  6. Aerosol Optical Retrieval and Surface Reflectance from Airborne Remote Sensing Data over Land

    PubMed Central

    Bassani, Cristiana; Cavalli, Rosa Maria; Pignatti, Stefano

    2010-01-01

    Quantitative analysis of atmospheric optical properties and surface reflectance can be performed by applying radiative transfer theory in the Atmosphere-Earth coupled system, for the atmospheric correction of hyperspectral remote sensing data. This paper describes a new physically-based algorithm to retrieve the aerosol optical thickness at 550nm (τ550) and the surface reflectance (ρ) from airborne acquired data in the atmospheric window of the Visible and Near-Infrared (VNIR) range. The algorithm is realized in two modules. Module A retrieves τ550 with a minimization algorithm, then Module B retrieves the surface reflectance ρ for each pixel of the image. The method was tested on five remote sensing images acquired by an airborne sensor under different geometric conditions to evaluate the reliability of the method. The results, τ550 and ρ, retrieved from each image were validated with field data contemporaneously acquired by a sun-sky radiometer and a spectroradiometer, respectively. Good correlation index, r, and low root mean square deviations, RMSD, were obtained for the τ550 retrieved by Module A (r2 = 0.75, RMSD = 0.08) and the ρ retrieved by Module B (r2 ≤ 0.9, RMSD ≤ 0.003). Overall, the results are encouraging, indicating that the method is reliable for optical atmospheric studies and the atmospheric correction of airborne hyperspectral images. The method does not require additional at-ground measurements about at-ground reflectance of the reference pixel and aerosol optical thickness. PMID:22163558

  7. Introduction to an airborne remote sensing system equipped onboard the Chinese marine surveillance plane

    NASA Astrophysics Data System (ADS)

    Gong, Fang; Wang, Difeng; Pan, Delu; Hao, Zengzhou

    2008-10-01

    The airborne remote sensing system onboard the Chinese Marine Surveillance Plane have three scanners including marine airborne multi-spectrum scanner(MAMS), airborne hyper spectral system(AISA+) and optical-electric platform(MOP) currently. MAMS is developed by Shanghai Institute of Technology and Physics CAS with 11 bands from ultraviolet to infrared and mainly used for inversion of oceanic main factors and pollution information, like chlorophyll, sea surface temperature, red tide, etc. The AISA+ made by Finnish Specim company is a push broom system, consist of a high spectrum scanner head, a miniature GPS/INS sensor and data collecting PC. It is a kind of aviation imaging spectrometer and has the ability of ground target imaging and measuring target spectrum characteristic. The MOP mainly supports for object watching, recording and track. It mainly includes 3 equipments: digital CCD with Sony-DXC390, CANON EOS film camera and digital camera Sony F717. This paper mainly introduces these three remote sensing instruments as well as the ground processing information system, involving the system's hardware and software design, related algorithm research, etc.

  8. Aerosol optical retrieval and surface reflectance from airborne remote sensing data over land.

    PubMed

    Bassani, Cristiana; Cavalli, Rosa Maria; Pignatti, Stefano

    2010-01-01

    Quantitative analysis of atmospheric optical properties and surface reflectance can be performed by applying radiative transfer theory in the Atmosphere-Earth coupled system, for the atmospheric correction of hyperspectral remote sensing data. This paper describes a new physically-based algorithm to retrieve the aerosol optical thickness at 550 nm (τ(550)) and the surface reflectance (ρ) from airborne acquired data in the atmospheric window of the Visible and Near-Infrared (VNIR) range. The algorithm is realized in two modules. Module A retrieves τ(550) with a minimization algorithm, then Module B retrieves the surface reflectance ρ for each pixel of the image. The method was tested on five remote sensing images acquired by an airborne sensor under different geometric conditions to evaluate the reliability of the method. The results, τ(550) and ρ, retrieved from each image were validated with field data contemporaneously acquired by a sun-sky radiometer and a spectroradiometer, respectively. Good correlation index, r, and low root mean square deviations, RMSD, were obtained for the τ(550) retrieved by Module A (r(2) = 0.75, RMSD = 0.08) and the ρ retrieved by Module B (r(2) ≤ 0.9, RMSD ≤ 0.003). Overall, the results are encouraging, indicating that the method is reliable for optical atmospheric studies and the atmospheric correction of airborne hyperspectral images. The method does not require additional at-ground measurements about at-ground reflectance of the reference pixel and aerosol optical thickness. PMID:22163558

  9. An investigative study of multispectral data compression for remotely-sensed images using vector quantization and difference-mapped shift-coding

    NASA Technical Reports Server (NTRS)

    Jaggi, S.

    1993-01-01

    A study is conducted to investigate the effects and advantages of data compression techniques on multispectral imagery data acquired by NASA's airborne scanners at the Stennis Space Center. The first technique used was vector quantization. The vector is defined in the multispectral imagery context as an array of pixels from the same location from each channel. The error obtained in substituting the reconstructed images for the original set is compared for different compression ratios. Also, the eigenvalues of the covariance matrix obtained from the reconstructed data set are compared with the eigenvalues of the original set. The effects of varying the size of the vector codebook on the quality of the compression and on subsequent classification are also presented. The output data from the Vector Quantization algorithm was further compressed by a lossless technique called Difference-mapped Shift-extended Huffman coding. The overall compression for 7 channels of data acquired by the Calibrated Airborne Multispectral Scanner (CAMS), with an RMS error of 15.8 pixels was 195:1 (0.41 bpp) and with an RMS error of 3.6 pixels was 18:1 (.447 bpp). The algorithms were implemented in software and interfaced with the help of dedicated image processing boards to an 80386 PC compatible computer. Modules were developed for the task of image compression and image analysis. Also, supporting software to perform image processing for visual display and interpretation of the compressed/classified images was developed.

  10. Ground-Based Remote Sensing of Water-Stressed Crops: Thermal and Multispectral Imaging

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Ground-based methods of remote sensing can be used as ground-truthing for satellite-based remote sensing, and in some cases may be a more affordable means of obtaining such data. Plant canopy temperature has been used to indicate and quantify plant water stress. A field research study was conducted ...

  11. Data processing of remotely sensed airborne hyperspectral data using the Airborne Processing Library (APL): Geocorrection algorithm descriptions and spatial accuracy assessment

    NASA Astrophysics Data System (ADS)

    Warren, Mark A.; Taylor, Benjamin H.; Grant, Michael G.; Shutler, Jamie D.

    2014-03-01

    Remote sensing airborne hyperspectral data are routinely used for applications including algorithm development for satellite sensors, environmental monitoring and atmospheric studies. Single flight lines of airborne hyperspectral data are often in the region of tens of gigabytes in size. This means that a single aircraft can collect terabytes of remotely sensed hyperspectral data during a single year. Before these data can be used for scientific analyses, they need to be radiometrically calibrated, synchronised with the aircraft's position and attitude and then geocorrected. To enable efficient processing of these large datasets the UK Airborne Research and Survey Facility has recently developed a software suite, the Airborne Processing Library (APL), for processing airborne hyperspectral data acquired from the Specim AISA Eagle and Hawk instruments. The APL toolbox allows users to radiometrically calibrate, geocorrect, reproject and resample airborne data. Each stage of the toolbox outputs data in the common Band Interleaved Lines (BILs) format, which allows its integration with other standard remote sensing software packages. APL was developed to be user-friendly and suitable for use on a workstation PC as well as for the automated processing of the facility; to this end APL can be used under both Windows and Linux environments on a single desktop machine or through a Grid engine. A graphical user interface also exists. In this paper we describe the Airborne Processing Library software, its algorithms and approach. We present example results from using APL with an AISA Eagle sensor and we assess its spatial accuracy using data from multiple flight lines collected during a campaign in 2008 together with in situ surveyed ground control points.

  12. Multispectral Thermal Infrared Mapping of Sulfur Dioxide Plumes: A Case Study from the East Rift Zone of Kilauea Volcano, Hawaii

    NASA Technical Reports Server (NTRS)

    Realmuto, V. J.; Sutton, A. J.; Elias, T.

    1996-01-01

    The synoptic perspective and rapid mode of data acquisition provided by remote sensing are well-suited for the study of volcanic SO2 plumes. In this paper we describe a plume-mapping procedure that is based on image data acquired with NASA's airborne Thermal Infrared Multispectral Scanner (TIMS).

  13. Using Google Earth for Rapid Dissemination of Airborne Remote Sensing Lidar and Photography

    NASA Astrophysics Data System (ADS)

    Wright, C. W.; Nayegandhi, A.; Brock, J. C.

    2006-12-01

    In order to visualize and disseminate vast amounts of lidar and digital photography data, we present a unique method that make these data layers available via the Google Earth interface. The NASA Experimental Advanced Airborne Research Lidar (EAARL) provides unprecedented capabilities to survey coral reefs, nearshore benthic habitats, coastal vegetation, and sandy beaches. The EAARL sensor suite includes a water-penetrating lidar that provides high-resolution topographic information, a down-looking color digital camera, a down-looking high-resolution color-infrared (CIR) digital camera, and precision kinematic GPS receivers which provide for sub-meter geo-referencing of each laser and multispectral sample. Google Earth "kml" files are created for each EAARL multispectral and processed lidar image. A hierarchical structure of network links allows the user to download high-resolution images within the region of interest. The first network link (kmz file) downloaded by the user contains a color coded flight path and "minute marker" icons along the flight path. Each "minute" icon provides access to the image overlays, and additional network links for each second along the flight path as well as flight navigation information. Layers of false-color-coded lidar Digital Elevation Model (DEM) data are made available in 2 km by 2km tiles. These layers include canopy-top, bare-Earth, submerged topography, and links to any other lidar products. The user has the option to download the x,y,z ascii point data or a DEM in the Geotif file format for each tile. The NASA EAARL project captured roughly 250,000 digital photographs in five flights conducted a few days after Hurricane Katrina made landfall along the Gulf Coast in 2005. All of the photos and DEM layers are georeferenced and viewable online using Google Earth.

  14. Computer classification of remotely sensed multispectral image data by extraction and classification of homogeneous objects

    NASA Technical Reports Server (NTRS)

    Kettig, R. L.

    1975-01-01

    A method of classification of digitized multispectral images is developed and experimentally evaluated on actual earth resources data collected by aircraft and satellite. The method is designed to exploit the characteristic dependence between adjacent states of nature that is neglected by the more conventional simple-symmetric decision rule. Thus contextual information is incorporated into the classification scheme. The principle reason for doing this is to improve the accuracy of the classification. For general types of dependence this would generally require more computation per resolution element than the simple-symmetric classifier. But when the dependence occurs in the form of redundance, the elements can be classified collectively, in groups, therby reducing the number of classifications required.

  15. Multispectral color photography for mineral exploration by the remote sensing of biogeochemical anomalies

    NASA Technical Reports Server (NTRS)

    Yost, E.

    1975-01-01

    Selected band multispectral photography was evaluated as a mineral exploration tool by detecting stress on trees caused by underground mineralization. Ground truth consisted of two test sites in the Prescott National Forest within which the mineralization had been established by a drilling program. Species of trees were categorized as background, intermediate, and anomalous based upon where they grew with respect to this underlying mineralization. Soil geochemistry and the metal content of ashed samples of the trees were studied in relation to the inferred locus of mineralization. Computer analysis of the reflectance spectra of mineralized trees confirmed that the relative percent reflectance differences of trees growing in anomalous areas was less than that of the same tree species growing in background areas.

  16. Colorimetric Detection of an Airborne Remote Photocatalytic Reaction Using a Stratified Ag Nanoparticle Sheet.

    PubMed

    Degawa, Ryo; Wang, Pangpang; Tanaka, Daisuke; Park, Susie; Sakai, Nobuyuki; Tatsuma, Tetsu; Okamoto, Koichi; Tamada, Kaoru

    2016-08-16

    Photocatalysts are practically used for decomposition of harmful and fouling organic compounds. Among the photocatalytic reactions, remote oxidation via airborne species is a relatively slow process, so that a sensitive technique for its detection has been awaiting. Here, we investigated an airborne remote photocatalytic reaction of a TiO2 photocatalyst modified with Pt nanoparticles as co-catalysts via the color change caused by a decomposition of a multilayered silver nanoparticle sheet. The silver nanoparticle sheet fabricated by the Langmuir-Schaefer method on a gold substrate exhibits a unique multicolor depending upon the number of layers. The color originates from multiple light trapping in the stratified sheets that has a metamaterial characteristic along with an intra- and interlayer coupling of localized surface plasmon resonance (LSPR). The stepwise decomposition of the sheets was confirmed by the colorimetric data, which exhibited not only a monotonic decrease but also a maximized absorption of light when the film thickness reached the optimal thickness for light trapping or when the oxidation of the Ag core started. Scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and surface plasmon resonance (SPR) spectroscopy data provided a complete view of the decomposition process of this inorganic-organic nanocomposite film, and simulation by the transfer-matrix method explained a simultaneous plasmonic response rationally. The influence of the humidity and gas flow rate on the airborne remote photocatalytic reaction kinetics was examined by this colorimetric detection method, and it suggests that H2O in air plays an essential role in the reaction. PMID:27445001

  17. An airborne remote sensing platform of the Helsinki University of Technology

    SciTech Connect

    Nikulainen, M.; Hallikainen, M.; Kemppinen, M.; Tauriainen, S.

    1996-10-01

    In 1994 Helsinki University of Technology acquired a Short SC7 Skyvan turboprop aircraft to be modified to carry remote sensing instruments. As the aircraft is originally designed to carry heavy and space consuming cargo, a modification program was implemented to make the aircraft feasible for remote sensing operations. The twelve-month long modification program had three design objectives: flexibility, accessibility and cost efficiency. The aircraft interior and electrical system were modified. Furthermore, the aircraft is equipped with DGPS-navigation system, multi-channel radiometer system and side looking airborne radar. Future projects include installation of local area network, attitude GPS system, imaging spectrometer and 1.4 GHz radiometer. 6 refs., 5 figs., 1 tab.

  18. Application of remotely sensed multispectral data to automated analysis of marshland vegetation. Inference to the location of breeding habitats of the salt marsh mosquito (Aedes Sollicitans)

    NASA Technical Reports Server (NTRS)

    Cibula, W. G.

    1976-01-01

    The techniques used for the automated classification of marshland vegetation and for the color-coded display of remotely acquired data to facilitate the control of mosquito breeding are presented. A multispectral scanner system and its mode of operation are described, and the computer processing techniques are discussed. The procedures for the selection of calibration sites are explained. Three methods for displaying color-coded classification data are presented.

  19. Algorithms research of airborne long linear multi-elements whisk broom remote sensing image geometric correction

    NASA Astrophysics Data System (ADS)

    Xu, Bin; Ma, Yan-hua; Li, Sheng-hong

    2015-10-01

    Multi-Element scanning imaging is an imaging method that is conventionally used in space-born spectrometer. By multipixel scanning at the same time, increased exposure time can be achieved and the picture quality can be enhanced. But when this imaging method is applied in airborne remote sensing image systems, corresponding imaging model and correction algorithms must be built, because of the poor posture stability of airborne platform and different characteristics and requirements. This paper builds a geometric correction model of airborne long linear multi-element scanning imaging system by decomposing the process of imaging and also deduced related correction algorithms. The sampling moment of linear CCD can be treated as push broom imaging and a single pixel imaging during the whole whisk broom period can be treated as whisk broom imaging. Based on this kind of decomposition, col-linearity equation correction algorithm and a kind of new tangent correction algorithm are deduced. As shown in the simulation experiment result, combining with position and attitude date collected by the posture position measurement system, these algorithms can map pixel position from image coordinate to WGS84 coordinate with high precision. In addition, some error factors and correction accuracy are roughly analyzed.

  20. Satellite and airborne aerosol remote sensing in the presence of clouds

    NASA Astrophysics Data System (ADS)

    Redemann, Jens; Russell, Philip; Zhang, Qin; Livingston, John; Shinozuka, Yohei; Mattoo, Shana; Remer, Lorraine

    2010-05-01

    Our ability to assess aerosol effects on climate using remote sensing data depends on the discrimination between cloudy and cloud-free viewing elements. Aerosol microphysical and related radiative properties have been shown to vary rapidly in the immediate vicinity of clouds, a circumstance that further complicates the distinction of cloudy from cloud-free pixels and the assessment of direct and indirect aerosol effects on climate. In this paper we will discuss the utility of simultaneous airborne and satellite aerosol remote sensing and each method's caveats in the presence of clouds. In a few select case studies, we will show how MODIS aerosol retrievals vary as a function of distance from clouds and we will discuss which of the variations found in the MODIS aerosol data can be verified using airborne remote sensing observations. In a case study of aerosol measurements near cloud edges within a dissipating stratiform cloud deck near the California coast in March 2004, we find that the MODIS-derived visible AOD agrees well with the sunphotometer-derived measurements, but that the SWIR (1240-2130nm) AOD increases near cloud edges are of the order of 0.03 and as such three times as large as the sunphotometer-derived values. The implications for the recently discussed "bluing" of aerosols near cloud edges, i.e., a preferential apparent increase in the visible reflectances of clear-sky pixels due to 3-D radiative transfer effects in the vicinity of clouds, are discussed. From a compilation of MODIS validation studies using airborne sunphotometer measurements in a large number of field campaigns we show that the agreement between sunphotometer and MODIS derived aerosol properties varies only slightly with the satellite-derived cloud fraction. We show further how the comparison of MODIS AOD to AOD derived from the CALIPSO backscatter lidar shows a significant dependence on cloud fraction, suggesting that the current version CALIPSO and MODIS data sets can only be

  1. Thermally modulated porous silica multispectral filters and their application in remote imaging.

    PubMed

    Garcia Sega, Adrian; King, Brian H; Lee, Jessica Y; Sailor, Michael J; Miskelly, Gordon M

    2013-09-24

    We report a thermally tunable multispectral imaging filter based on reversible condensation of volatile organic fluids within a nanoporous one-dimensional photonic crystal. The photonic crystal (optical rugate filter) comprises oxidized porous silicon, prepared by electrochemical etch of silicon and subsequent air oxidation (porous silica rugate filter, pSiF). The reflectance spectrum of the pSiF is designed and constructed to match two of the red emission bands of the luminescent complex europium(III) tris-dipicolinate, [Eu(dpa)3](3-), which has been used as an indicator for anthrax spores. When the pSiF is fitted with a thermoelectric Peltier cooler/heater and sealed in a container with 2-propanol vapor, microcapillary effects drive the temperature-dependent condensation/evaporation of 2-propanol into/out of the porous nanostructure. Thermal cycling experiments show that the wavelengths of the spectral bands of the pSiF are reversibly tuned by ±35 nm for a temperature change of ±40 °C. Difference images of a UV-illuminated scene containing the [Eu(dpa)3](3-) target, obtained by reflection from pSiF that is continuously thermally cycled through the emission bands of the dye, show that the target can be discriminated from the background or from control targets with overlapping but dissimilar luminescence spectra. PMID:23968219

  2. Remote detection of volatile organic compounds by passive multispectral infrared imaging measurements.

    PubMed

    Wabomba, Mukire J; Sulub, Yusuf; Small, Gary W

    2007-04-01

    Automated pattern recognition methodology is described for the detection of signatures of volatile organic compounds from passive multispectral infrared imaging data collected from an aircraft platform. Data are acquired in an across-track scanning mode with a downward-looking line scanner based on 8 to 16 spectral channels in the 8-14 and 3-5 microm spectral ranges. Two controlled release experiments are performed in which plumes of ethanol are generated and detected from aircraft overflights at altitudes of 2200 to 2800 ft (671 to 853 m). In addition, a methanol release from a chemical manufacturing facility is monitored. Automated classifiers are developed by application of piecewise linear discriminant analysis to the calibrated, registered, and preprocessed radiance data acquired by the line scanner. Preprocessing steps evaluated include contrast enhancement, temperature-emissivity separation, feature selection, and feature extraction/noise reduction by the minimum noise fraction (MNF) transform. Successful classifiers are developed for both compounds and are tested with data not used in the classifier development. Separation of temperature and emissivity by use of the alpha residual calculation is found to reduce false positive detections to a negligible level, and the MNF transform is shown to enhance detection sensitivity. PMID:17456252

  3. Multi-Spectral Pushbroom Imaging Radiometer (MPIR) for remote sensing studies

    SciTech Connect

    Phipps, GS; Grotbeck, CL

    1996-05-01

    A Multi-spectral Pushbroom Imaging Radiometer (MPIR) has been developed as a well-calibrated, imaging radiometer for studies of cloud properties from an unmanned aerospace vehicle platform. The instrument is designed to fly at altitudes up to 20 km and produce data from nine spectral detector modules. Each module has its own telescope optics, linear detector array, spectral filter, and necessary electronics. Cryogenic cooling for the long-wavelength infrared modules, as well as temperature regulation of the short- wavelength modules, is provided by a liquid nitrogen system designed to operate for multi-day missions. Pre- and post-flight calibration, combined with an on-board calibration chopper, provide an instrument with state-of-the-art radiometric measurement accuracies. Each module has a {+-}40{degree} across-track field-of-view and images a curved footprint onto its linear detector array. The long-wavelength array types have 256 detector elements while the short-wavelength arrays can have 512 elements. A modular design allows individual spectral bands to be changed to match the requirements for a particular mission.

  4. Remote Sensing of Wind Fields and Aerosol Distribution with Airborne Scanning Doppler Lidar

    NASA Technical Reports Server (NTRS)

    Rothermel, Jeffry; Cutten, Dean R.; Johnson, Steven C.; Jazembski, Maurice; Arnold, James E. (Technical Monitor)

    2001-01-01

    The coherent Doppler laser radar (lidar), when operated from an airborne platform, is a unique tool for the study of atmospheric and surface processes and features. This is especially true for scientific objectives requiring measurements in optically-clear air, where other remote sensing technologies such as Doppler radar are typically at a disadvantage. The atmospheric lidar remote sensing groups of several US institutions, led by Marshall Space Flight Center, have developed an airborne coherent Doppler lidar capable of mapping the wind field and aerosol structure in three dimensions. The instrument consists of an eye-safe approx. 1 Joule/pulse lidar transceiver, telescope, scanner, inertial measurement unit, and flight computer system to orchestrate all subsystem functions and tasks. The scanner is capable of directing the expanded lidar beam in a variety of ways, in order to extract vertically-resolved wind fields. Horizontal resolution is approx. 1 km; vertical resolution is even finer. Winds are obtained by measuring backscattered, Doppler-shifted laser radiation from naturally-occurring aerosol particles (of order 1 micron diameter). Measurement coverage depends on aerosol spatial distribution and composition. Velocity accuracy has been verified to be approx. 1 meter per second. A variety of applications have been demonstrated during the three flight campaigns conducted during 1995-1998. Examples will be shown during the presentation. In 1995, boundary layer winds over the ocean were mapped with unprecedented resolution. In 1996, unique measurements were made of. flow over the complex terrain of the Aleutian Islands; interaction of the marine boundary layer jet with the California coastal mountain range; a weak dry line in Texas - New Mexico; the angular dependence of sea surface scattering; and in-flight radiometric calibration using the surface of White Sands National Monument. In 1998, the first measurements of eyewall and boundary layer winds within a

  5. AIRBORNE, OPTICAL REMOTE SENSING OF METHANE AND ETHANE FOR NATURAL GAS PIPELINE LEAK DETECTION

    SciTech Connect

    Jerry Myers

    2003-05-13

    Ophir Corporation was awarded a contract by the U. S. Department of Energy, National Energy Technology Laboratory under the Project Title ''Airborne, Optical Remote Sensing of Methane and Ethane for Natural Gas Pipeline Leak Detection'' on October 14, 2002. This six-month technical report summarizes the progress for each of the proposed tasks, discusses project concerns, and outlines near-term goals. Ophir has completed a data survey of two major natural gas pipeline companies on the design requirements for an airborne, optical remote sensor. The results of this survey are disclosed in this report. A substantial amount of time was spent on modeling the expected optical signal at the receiver at different absorption wavelengths, and determining the impact of noise sources such as solar background, signal shot noise, and electronic noise on methane and ethane gas detection. Based upon the signal to noise modeling and industry input, Ophir finalized the design requirements for the airborne sensor, and released the critical sensor light source design requirements to qualified vendors. Responses from the vendors indicated that the light source was not commercially available, and will require a research and development effort to produce. Three vendors have responded positively with proposed design solutions. Ophir has decided to conduct short path optical laboratory experiments to verify the existence of methane and absorption at the specified wavelength, prior to proceeding with the light source selection. Techniques to eliminate common mode noise were also evaluated during the laboratory tests. Finally, Ophir has included a summary of the potential concerns for project success and has established future goals.

  6. A fully-automated approach to land cover mapping with airborne LiDAR and high resolution multispectral imagery in a forested suburban landscape

    NASA Astrophysics Data System (ADS)

    Parent, Jason R.; Volin, John C.; Civco, Daniel L.

    2015-06-01

    Information on land cover is essential for guiding land management decisions and supporting landscape-level ecological research. In recent years, airborne light detection and ranging (LiDAR) and high resolution aerial imagery have become more readily available in many areas. These data have great potential to enable the generation of land cover at a fine scale and across large areas by leveraging 3-dimensional structure and multispectral information. LiDAR and other high resolution datasets must be processed in relatively small subsets due to their large volumes; however, conventional classification techniques cannot be fully automated and thus are unlikely to be feasible options when processing large high-resolution datasets. In this paper, we propose a fully automated rule-based algorithm to develop a 1 m resolution land cover classification from LiDAR data and multispectral imagery. The algorithm we propose uses a series of pixel- and object-based rules to identify eight vegetated and non-vegetated land cover features (deciduous and coniferous tall vegetation, medium vegetation, low vegetation, water, riparian wetlands, buildings, low impervious cover). The rules leverage both structural and spectral properties including height, LiDAR return characteristics, brightness in visible and near-infrared wavelengths, and normalized difference vegetation index (NDVI). Pixel-based properties were used initially to classify each land cover class while minimizing omission error; a series of object-based tests were then used to remove errors of commission. These tests used conservative thresholds, based on diverse test areas, to help avoid over-fitting the algorithm to the test areas. The accuracy assessment of the classification results included a stratified random sample of 3198 validation points distributed across 30 1 × 1 km tiles in eastern Connecticut, USA. The sample tiles were selected in a stratified random manner from locations representing the full range of

  7. Above-ground biomass estimation of tuberous bulrush ( Bolboschoenus planiculmis) in mudflats using remotely sensed multispectral image

    NASA Astrophysics Data System (ADS)

    Kim, Ji Yoon; Im, Ran-Young; Do, Yuno; Kim, Gu-Yeon; Joo, Gea-Jae

    2016-03-01

    We present a multivariate regression approach for mapping the spatial distribution of above-ground biomass (AGB) of B. planiculmis using field data and coincident moderate spatial resolution satellite imagery. A total of 232 ground sample plots were used to estimate the biomass distribution in the Nakdong River estuary. Field data were overlain and correlated with digital values from an atmospherically corrected multispectral image (Landsat 8). The AGB distribution was derived using empirical models trained with field-measured AGB data. The final regression model for AGB estimation was composed using the OLI3, OLI4, and OLI7 spectral bands. The Pearson correlation between the observed and predicted biomass was significant (R = 0.84, p < 0.0001). OLI3 made the largest contribution to the final model (relative coefficient value: 53.4%) and revealed a negative relationship with the AGB biomass. The total distribution area of B. planiculmis was 1,922,979 m2. Based on the model estimation, the total AGB had a dry weight (DW) of approximately 298.2 tons. The distribution of high biomass stands (> 200 kg DW/900 m2) constituted approximately 23.91% of the total vegetated area. Our findings suggest the expandability of remotely sensed products to understand the distribution pattern of estuarine plant productivity at the landscape level.

  8. TACMSI: a novel multi-look multispectral imager for maritime mine detection

    NASA Astrophysics Data System (ADS)

    Leonard, Carrie L.; Chan, Chong Wai; Cottis, Tamara; DeWeert, Michael; Dichner, Michael; Farm, Brian; Kokubun, Dan; Louchard, Eric; Noguchi, Reid; Topping, Miles; Wong, Timothy; Yoon, Dugan

    2008-04-01

    Airborne EO imagery, including wideband, hyperspectral, and multispectral modalities, has greatly enhanced the ability of the ISR community to detect and classify various targets of interest from long standoff distances and with large area coverage rates. The surf zone is a dynamic environment that presents physical and operational challenges to effective remote sensing with optical systems. In response to these challenges, BAE Systems has developed the Tactical Multi-spectral (TACMSI) system. The system includes a VNIR six-band multispectral sensor and all other hardware that is used to acquire, store and process imagery, navigation, and supporting metadata on the airborne platform. In conjunction with the hardware, BAE Systems has innovative data processing methods that exploit the inherent capabilities of multi-look framing imagery to essentially remove the overlying clutter or obscuration to enable EO visualization of the objects of interest.

  9. Lithology intelligent identification using support vector machine and adaptive cellular automata in multispectral remote sensing image

    NASA Astrophysics Data System (ADS)

    Wang, Xianmin; Niu, Ruiqing; Wu, Ke

    2011-07-01

    Remote sensing provides a new idea and an advanced method for lithology identification, but lithology identification by remote sensing is quite difficult because 1. the disciplines of lithology identification in a concrete region are often quite different from the experts' experience; 2. in the regions with flourishing vegetation, lithology information is poor, so it is very difficult to identify the lithologies by remote sensing images. At present, the studies on lithology identification by remote sensing are primarily conducted on the regions with low vegetation coverage and high rock bareness. And there is no mature method of lithology identification in the regions with flourishing vegetation. Traditional methods lacking in the mining and extraction of the various complicated lithology information from a remote sensing image, often need much manual intervention and possess poor intelligence and accuracy. An intelligent method proposed in this paper for lithology identification based on support vector machine (SVM) and adaptive cellular automata (ACA) is expected to solve the above problems. The method adopted Landsat-7 ETM+ images and 1:50000 geological map as the data origins. It first derived the lithology identification factors on three aspects: 1. spectra, 2. texture and 3. vegetation cover. Second, it plied the remote sensing images with the geological map and established the SVM to obtain the transition rules according to the factor values of the samples. Finally, it established an ACA model to intelligently identify the lithologies according to the transition and neighborhood rules. In this paper an ACA model is proposed and compared with the traditional one. Results of 2 real-world examples show that: 1. The SVM-ACA method obtains a good result of lithology identification in the regions with flourishing vegetation; 2. it possesses high accuracies of lithology identification (with the overall accuracies of 92.29% and 85.54%, respectively, in the two

  10. Land cover mapping at Alkali Flat and Lake Lucero, White Sands, New Mexico, USA using multi-temporal and multi-spectral remote sensing data

    NASA Astrophysics Data System (ADS)

    Ghrefat, Habes A.; Goodell, Philip C.

    2011-08-01

    The goal of this research is to map land cover patterns and to detect changes that occurred at Alkali Flat and Lake Lucero, White Sands using multispectral Landsat 7 Enhanced Thematic Mapper Plus (ETM+), Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER), Advanced Land Imager (ALI), and hyperspectral Hyperion and Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) data. The other objectives of this study were: (1) to evaluate the information dimensionality limits of Landsat 7 ETM+, ASTER, ALI, Hyperion, and AVIRIS data with respect to signal-to-noise and spectral resolution, (2) to determine the spatial distribution and fractional abundances of land cover endmembers, and (3) to check ground correspondence with satellite data. A better understanding of the spatial and spectral resolution of these sensors, optimum spectral bands and their information contents, appropriate image processing methods, spectral signatures of land cover classes, and atmospheric effects are needed to our ability to detect and map minerals from space. Image spectra were validated using samples collected from various localities across Alkali Flat and Lake Lucero. These samples were measured in the laboratory using VNIR-SWIR (0.4-2.5 μm) spectra and X-ray Diffraction (XRD) method. Dry gypsum deposits, wet gypsum deposits, standing water, green vegetation, and clastic alluvial sediments dominated by mixtures of ferric iron (ferricrete) and calcite were identified in the study area using Minimum Noise Fraction (MNF), Pixel Purity Index (PPI), and n-D Visualization. The results of MNF confirm that AVIRIS and Hyperion data have higher information dimensionality thresholds exceeding the number of available bands of Landsat 7 ETM+, ASTER, and ALI data. ASTER and ALI data can be a reasonable alternative to AVIRIS and Hyperion data for the purpose of monitoring land cover, hydrology and sedimentation in the basin. The spectral unmixing analysis and dimensionality eigen

  11. A survey of natural aggregate properties and characteristics important in remote sensing and airborne geophysics

    USGS Publications Warehouse

    Knepper, D.H., Jr.; Langer, W.H.; Miller, S.

    1995-01-01

    Natural aggregate is vital to the construction industry. Although natural aggregate is a high volume/low value commodity that is abundant, new sources are becoming increasingly difficult to find and develop because of rigid industry specifications, political considerations, development and transportation costs, and environmental concerns. There are two primary sources of natural aggregate: (1) exposed or near-surface bedrock that can be crushed, and (2) deposits of sand and gravel. Remote sensing and airborne geophysics detect surface and near-surface phenomena, and may be useful for detecting and mapping potential aggregate sources; however, before a methodology for applying these techniques can be developed, it is necessary to understand the type, distribution, physical properties, and characteristics of natural aggregate deposits. The distribution of potential aggregate sources is closely tied to local geologic history. Conventional exploration for natural aggregate deposits has been largely a ground-based operation, although aerial photographs and topographic maps have been extensively used to target possible deposits. Today, the exploration process also considers factors such as the availability of the land, space and water supply for processing, political and environmental factors, and distance from the market; exploration and planning cannot be separated. There are many physical properties and characteristics by which to judge aggregate material for specific applications; most of these properties and characteristics pertain only to individual aggregate particles. The application of remote sensing and airborne geophysical measurements to detecting and mapping potential aggregate sources, however, is based on intrinsic bulk physical properties and extrinsic characteristics of the deposits that can be directly measured, mathematically derived from measurement, or interpreted with remote sensing and geophysical data. ?? 1995 Oxford UniversityPress.

  12. Use of reflectance spectra of native plant species for interpreting airborne multispectral scanner data in the East Tintic Mountains, Utah.

    USGS Publications Warehouse

    Milton, N.M.

    1983-01-01

    Analysis of in situ reflectance spectra of native vegetation was used to interpret airborne MSS data. Representative spectra from three plant species in the E Tintic Mountains, Utah, were used to interpret the color components on a color ratio composite image made from MSS data in the visible and near-infrared regions. A map of plant communities was made from the color ratio composite image and field checked. -from Author

  13. A Generic Procedure for BRDF Normalization of Remotely Sensed Data

    SciTech Connect

    D. Yuan

    2003-04-01

    A generic procedure for Bidirectional Reflectance Distribution Function (BRDF) normalization for airborne multispectral images has been developed and implemented as an add-on module of ENVI at the U.S. Department of Energy's Remote Sensing Laboratory. The main advantage of this procedure is that it does not require multiple image acquisitions over the same area for establishing empirical BRDF functions.

  14. [Remote sensing of chlorophyll fluorescence at airborne level based on unmanned airship platform and hyperspectral sensor].

    PubMed

    Yang, Pei-Qi; Liu, Zhi-Gang; Ni, Zhuo-Ya; Wang, Ran; Wang, Qing-Shan

    2013-11-01

    The solar-induced chlorophyll fluorescence (ChlF) has a close relationship with photosynthetic and is considered as a probe of plant photosynthetic activity. In this study, an airborne fluorescence detecting system was constructed by using a hyperspectral imager on board an unmanned airship. Both Fraunhofer Line Discriminator (FLD) and 3FLD used to extract ChlF require the incident solar irradiance, which is always difficult to receive at airborne level. Alternative FLD (aFLD) can overcome the problem by selecting non-fluorescent emitter in the image. However, aFLD is based on the assumption that reflectance is identical around the Fraunhofer line, which is not realistic. A new method, a3FLD, is proposed, which assumes that reflectance varies linearly with the wavelength around Fraunhofer line. The result of simulated data shows that ChlF retrieval error of a3FLD is significantly lower than that of aFLD when vegetation reflectance varies near the Fraunhofer line. The results of hyperspectral remote sensing data with the airborne fluorescence detecting system show that the relative values of retrieved ChlF of 5 kinds of plants extracted by both aFLD and a3FLD are consistent with vegetation growth stage and the ground-level ChlF. The ChlF values of aFLD are about 15% greater than a3FLD. In addition, using aFLD, some non-fluorescent objects have considerable ChlF value, while a3FLD can effectively overcome the problem. PMID:24555390

  15. Land cover/use classification of Cairns, Queensland, Australia: A remote sensing study involving the conjunctive use of the airborne imaging spectrometer, the large format camera and the thematic mapper simulator

    NASA Technical Reports Server (NTRS)

    Heric, Matthew; Cox, William; Gordon, Daniel K.

    1987-01-01

    In an attempt to improve the land cover/use classification accuracy obtainable from remotely sensed multispectral imagery, Airborne Imaging Spectrometer-1 (AIS-1) images were analyzed in conjunction with Thematic Mapper Simulator (NS001) Large Format Camera color infrared photography and black and white aerial photography. Specific portions of the combined data set were registered and used for classification. Following this procedure, the resulting derived data was tested using an overall accuracy assessment method. Precise photogrammetric 2D-3D-2D geometric modeling techniques is not the basis for this study. Instead, the discussion exposes resultant spectral findings from the image-to-image registrations. Problems associated with the AIS-1 TMS integration are considered, and useful applications of the imagery combination are presented. More advanced methodologies for imagery integration are needed if multisystem data sets are to be utilized fully. Nevertheless, research, described herein, provides a formulation for future Earth Observation Station related multisensor studies.

  16. An Integrated Multiangle, Multispectral, and Polarimetric Imaging Concept for Aerosol Remote Sensing from Space

    NASA Technical Reports Server (NTRS)

    Diner, David J.; Chipman, Russell A.; Beaudry, Neil; Cairns, Brian; Foo, Leslie D.; Macenka, Steven A.; Cunningham, Thomas J.; Seshadri, Suresh; Keller, Christoph

    2004-01-01

    Techniques for passive remote sensing of aerosol optical and microphysical properties from space include visible, near and shortwave-infrared imaging (e.g., from MODIS), multiangle intensity imaging (e.g., ATSR-2, AATSR, MISR), near-ultraviolet mapping (e.g., TOMSIOMI), and polarimetry (e.g., POLDER, APS). Each of these methods has unique strengths. In this paper, we present a concept for integrating these approaches into a unified sensor. Design goals include spectral coverage from the near-UV to the shortwave infrared; intensity and polarimetric imaging simultaneously at multiple view angles; global coverage within a few days; kilometer to sub-kilometer spatial resolution; and measurement of the degree of linear polarization (DOLP) for a subset of the spectral complement with an uncertainty of 0.5% or less.

  17. Multispectral remote observations of hydrologic features on the North Slope of Alaska

    NASA Technical Reports Server (NTRS)

    Hall, D. K.; Bryan, M. L.

    1977-01-01

    Visible and near-infrared Landsat satellite imagery and active and passive aircraft microwave data are used to analyze some hydrologic features in Arctic Alaska. Lake studies using passive microwave imagery reveal that an increase in the microwave brightness temperature correlates with an increase in ice thickness. Synthetic Aperture Radar (SAR) imagery allows determination of lakes that are frozen to the bottom under certain conditions. Landsat imagery of lakes can be used to study summer ice cover dissipation, an indicator of lake depth. River channel morphometry and morphology studies are accomplished using SAR data with good (25 m) resolution. Landsat imagery is shown to be useful for analyzing interannual variations in the extent of river icings (aufeis). Snow depth variations are shown to be potentially discernable using passive microwave data. Finally, the present and potential applications of these remote sensing studies are discussed; these data are useful for locating potable water sources, planning construction in good locations, and for analyzing interannual climate fluctuations.

  18. Remote sensing of surface hemispherical reflectance (albedo) using pointable multispectral imaging spectroradiometers

    NASA Technical Reports Server (NTRS)

    Kimes, D. S.; Deering, D. W.

    1992-01-01

    Remote techniques for determining albedo are examined in terms of the range of view angles required in the use of string techniques with the Moderate Resolution Imaging Spectroradiometer (MODIS) and the High Resolution Imaging Spectroradiometer (HIRIS). Ground data are used to compute full and half strings out to 15, 30, 45, and 60 degrees for various sun angles and ground cover types. A knowledge-based system is employed to evaluate both the visible and near-IR bands, and the results indicate errors of up to 7 percent for the MODIS data, HIRIS data, and the full-string +/- 60 degrees. In the cases of large extrapolations greater ranges of error are noted indicating that 60-deg systems are most effective. The error is increased in the case of sensor systems that only view in the fore or aft direction, and the MODIS full string for +/- 45 deg is also considered a good system.

  19. The analytical design of spectral measurements for multispectral remote sensor systems

    NASA Technical Reports Server (NTRS)

    Wiersma, D. J.; Landgrebe, D. A. (Principal Investigator)

    1979-01-01

    The author has identified the following significant results. In order to choose a design which will be optimal for the largest class of remote sensing problems, a method was developed which attempted to represent the spectral response function from a scene as accurately as possible. The performance of the overall recognition system was studied relative to the accuracy of the spectral representation. The spectral representation was only one of a set of five interrelated parameter categories which also included the spatial representation parameter, the signal to noise ratio, ancillary data, and information classes. The spectral response functions observed from a stratum were modeled as a stochastic process with a Gaussian probability measure. The criterion for spectral representation was defined by the minimum expected mean-square error.

  20. Passive multispectral imaging polarimeter for remote atmospheric and surface studies: design based on optical coatings.

    PubMed

    Pellicori, Samuel F; Burke, Elliot

    2016-02-20

    The passive imaging polarimeter architecture is based on optical coatings and thereby avoids the complexities of current systems that use rotating polarizers, phase-modulating retarders, and birefringent elements. Coatings on stationary elements separate spectral regions and their polarized components to simultaneously produce images of the Stokes linear polarization intensities in fields of view (FOVs) ≥30°. Wavelength and FOV coverages are limited only by the telescope and relay optics employed. The images are collected in identical spectral passbands that can extend from UV to shortwave IR. An example relevant to remote sensing in the 360-900 nm range is given. An on-board calibration and stability monitor is included. PMID:26906581

  1. An infrared remote sensor with high integration and multi-spectral bands

    NASA Astrophysics Data System (ADS)

    Zhang, Lisha; Liu, Zhaojun; Ma, Wenpo; Tang, Shaofan; Hu, Bin

    2014-11-01

    Along with the further application of optical remote sensing, it becomes main trend to realize high spatial resolution, high time resolution, high spectrum resolution and high irradiance sensitivity simultaneously. We present a new satellite-based imaging system that will provide images with these high performances. The structure of the system is compact with small size and light weight. The IR imager, a new generation of high resolution optical remote sensing, is universally acknowledged as the most effective approach to surveil dynamic changes in the environment on the earth. Pushbroom imaging fashion with high efficiency and long-array focal plane detector with passive cooling are adopted to realize area imaging relevant to the flight direction of satellite. The instrument is a dual-optical-path system with long-wave infrared (LWIR) and mid-short-wave infrared (MW-SWIR) bands - which has 4 narrow spectrum bands respectively. An IR dichroic beam-splitter is use to divide wideband incident infrared into LWIR and MW-SWIR. Then two pieces of joint filters, which are integrated in front of detectors and then enveloped by IR Dewars, are used to divide the LWIR and MWIR into 4 spectral bands separately. The focal plane arrays (FPA) are fixed on the optical imaging plane of the lens. The LWIR and MW-SWIR FPA are cooled around 80K or even below. For cooled FPA, optical system must provide a real, accessible exit pupil coupled with a fast f/number refractive component in a Dewar and very close to the FPA. Compared to traditional infrared instruments, high spatial resolution and spectrum resolution can be obtained simultaneously within mass, volume and performance constraints.

  2. Light weight airborne imaging spectrometer remote sensing system for mineral exploration in China

    NASA Astrophysics Data System (ADS)

    Wu, Taixia; Zhang, Lifu; Cen, Yi; Wang, Jinnian; Tong, Qingxi

    2014-05-01

    Imaging spectrometers provide the unique combination of both spatially contiguous spectra and spectrally contiguous images of the Earth's surface that allows spatial mapping of these minerals. One of the successful applications of imaging spectrometers remote sensing identified was geological mapping and mineral exploration. A Light weight Airborne Imaging Spectrometer System (LAISS) has been developed in China. The hardware of the compact LAISS include a VNIR imaging spectrometer, a SWIR imaging spectrometer, a high resolution camera and a position and attitude device. The weight of the system is less than 20kg. The VNIR imaging spectrometer measures incoming radiation in 344 contiguous spectral channels in the 400-1000 nm wavelength range with spectral resolution of better than 5 nm and creates images of 464 pixels for a line of targets with a nominal instantaneous field of view (IFOV) of ~1 mrad. The SWIR imaging spectrometer measures incoming radiation in the 1000-2500 nm wavelength range with spectral resolution of better than 10 nm with a nominal instantaneous field of view (IFOV) of ~2 mrad. The 400 to 2500nm spectral range provides abundant information about many important Earth-surface minerals. A ground mineral scan experiment and an UAV carried flying experiment has been done. The experiment results show the LAISS have achieved relative high performance levels in terms of signal to noise ratio and image quality. The potential applications for light weight airborne imaging spectrometer system in mineral exploration are tremendous.

  3. The airborne Laser Absorption Spectrometer - A new instrument of remote measurement of atmospheric trace gases

    NASA Technical Reports Server (NTRS)

    Shumate, M. S.; Menzies, R. T.

    1978-01-01

    The Laser Absorption Spectrometer is a portable instrument developed by JPL for remote measurement of trace gases from an aircraft platform. It contains two carbon dioxide lasers, two optical heterodyne receivers, appropriate optics to aim the lasers at the ground and detect the backscattered energy, and signal processing and recording electronics. Operating in the differential-absorption mode, it is possible to monitor one atmospheric gas at a time and record the data in real time. The system can presently measure ozone, ethylene, water vapor, and chlorofluoromethanes with high sensitivity. Airborne measurements were made in early 1977 from the NASA/JPL twin-engine Beechcraft and in May 1977 from the NASA Convair 990 during the ASSESS-II Shuttle Simulation Study. These flights resulted in measurements of ozone concentrations in the lower troposphere which were compared with ground-based values provided by the Air Pollution Control District. This paper describes the details of the instrument and results of the airborne measurements.

  4. Analysis of testbed airborne multispectral scanner data from Superflux II. [Chesapeake Bay plume and James Shelf data

    NASA Technical Reports Server (NTRS)

    Bowker, D. E.; Hardesty, C. A.; Jobson, D. J.; Bahn, G. S.

    1981-01-01

    A test bed aircraft multispectral scanner (TBAMS) was flown during the James Shelf, Plume Scan, and Chesapeake Bay missions as part of the Superflux 2 experiment. Excellent correlations were obtained between water sample measurements of chlorophyll and sediment and TBAMS radiance data. The three-band algorithms used were insensitive to aircraft altitude and varying atmospheric conditions. This was particularly fortunate due to the hazy conditions during most of the experiments. A contour map of sediment, and also chlorophyll, was derived for the Chesapeake Bay plume along the southern Virginia-Carolina coastline. A sediment maximum occurs about 5 nautical miles off the Virginia Beach coast with a chlorophyll maximum slightly shoreward of this. During the James Shelf mission, a thermal anomaly (or front) was encountered about 50 miles from the coast. There was a minor variation in chlorophyll and sediment across the boundary. During the Chesapeake Bay mission, the Sun elevation increased from 50 degrees to over 70 degrees, interfering with the generation of data products.

  5. Effective Key Parameter Determination for an Automatic Approach to Land Cover Classification Based on Multispectral Remote Sensing Imagery

    PubMed Central

    Wang, Yong; Jiang, Dong; Zhuang, Dafang; Huang, Yaohuan; Wang, Wei; Yu, Xinfang

    2013-01-01

    The classification of land cover based on satellite data is important for many areas of scientific research. Unfortunately, some traditional land cover classification methods (e.g. known as supervised classification) are very labor-intensive and subjective because of the required human involvement. Jiang et al. proposed a simple but robust method for land cover classification using a prior classification map and a current multispectral remote sensing image. This new method has proven to be a suitable classification method; however, its drawback is that it is a semi-automatic method because the key parameters cannot be selected automatically. In this study, we propose an approach in which the two key parameters are chosen automatically. The proposed method consists primarily of the following three interdependent parts: the selection procedure for the pure-pixel training-sample dataset, the method to determine the key parameters, and the optimal combination model. In this study, the proposed approach employs both overall accuracy and their Kappa Coefficients (KC), and Time-Consumings (TC, unit: second) in order to select the two key parameters automatically instead of using a test-decision, which avoids subjective bias. A case study of Weichang District of Hebei Province, China, using Landsat-5/TM data of 2010 with 30 m spatial resolution and prior classification map of 2005 recognised as relatively precise data, was conducted to test the performance of this method. The experimental results show that the methodology determining the key parameters uses the portfolio optimisation model and increases the degree of automation of Jiang et al.'s classification method, which may have a wide scope of scientific application. PMID:24204582

  6. Chronology and backtracking of oil slick trajectory to source in offshore environments using ultraspectral to multispectral remotely sensed data

    NASA Astrophysics Data System (ADS)

    Lammoglia, Talita; Souza Filho, Carlos Roberto de

    2015-07-01

    Offshore natural seepage confirms the occurrence of an active petroleum system with thermal maturation and migration, regardless its economic viability for petroleum production. Ocean dynamics, however, impose a challenge for correlation between oil seeps detected on the water surface and its source at the ocean floor. This hinders the potential use of seeps in petroleum exploration. The present study aims to estimate oil exposure time on the water surface via remote sensing in order to help locating ocean floor seepage sources. Spectral reflectance properties of a variety of fresh crude oils, oil films on water and oil-water emulsions were determined. Their spectral identity was used to estimate the duration of exposure of oil-water emulsions based on their temporal spectral responses. Laboratory models efficiently predicted oil status using ultraspectral (>2000 bands), hyperspectral (>300 bands), and multispectral (<10 bands) sensors covering near infrared and shortwave infrared wavelengths. An oil seepage recorded by the ASTER sensor on the Brazilian coast was used to test the designed predictive model. Results indicate that the model can successfully forecast the timeframe of crude oil exposure in the ocean (i.e., the relative "age" of the seepage). The limited spectral resolution of the ASTER sensor, though, implies less accurate estimates compared to higher resolution sensors. The spectral libraries and the method proposed here can be reproduced for other oceanic areas in order to approximate the duration of exposure of noticeable natural oil seepages. This type of information is optimal for seepage tracing and, therefore, for oceanic petroleum exploration and environmental monitoring.

  7. Combined multispectral/hyperspectral remote sensing of tropospheric aerosols for quantification of their direct radiative effect

    NASA Astrophysics Data System (ADS)

    McGarragh, Gregory R.

    Scattering and absorption of solar radiation by aerosols in the atmosphere has a direct radiative effect on the climate of the Earth. Unfortunately, according to the IPCC the uncertainties in aerosol properties and their effect on the climate system represent one of the largest uncertainties in climate change research. Related to aerosols, one of the largest uncertainties is the fraction of the incident radiation that is scattered rather than absorbed, or their single scattering albedo. In fact, differences in single scattering albedo have a significant impact on the magnitude of the cooling effect of aerosols (opposite to that of greenhouse gasses) which can even have a warming effect for strongly absorbing aerosols. Satellites provide a unique opportunity to measure aerosol properties on a global scale. Traditional approaches use multispectral measurements of intensity at a single view angle to retrieve at most two aerosol parameters over land but it is being realized that more detail is required for accurate quantification of the direct effect of aerosols, in particular its anthropogenic component, and therefore more measurement information is required. One approach to more advanced measurements is to use not only intensity measurements but also polarimetric measurements and to use multiple view angles. In this work we explore another alternative: the use of hyperspectral measurements in molecular absorption bands. Our study can be divided into three stages the first of which is the development of a fast radiative transfer model for rapid simulation of measurements. Our approach is matrix operator based and uses the Pade approximation for the matrix exponential to evaluate the homogeneous solution. It is shown that the method is two to four times faster than the standard and efficient discrete ordinate technique and is accurate to the 6th decimal place. The second part of our study forms the core and is divided into two chapters the first of which is a rigorous

  8. Combined multispectral/hyperspectral remote sensing of tropospheric aerosols for quantification of their direct radiative effect

    NASA Astrophysics Data System (ADS)

    McGarragh, Gregory R.

    Scattering and absorption of solar radiation by aerosols in the atmosphere has a direct radiative effect on the climate of the Earth. Unfortunately, according to the IPCC the uncertainties in aerosol properties and their effect on the climate system represent one of the largest uncertainties in climate change research. Related to aerosols, one of the largest uncertainties is the fraction of the incident radiation that is scattered rather than absorbed, or their single scattering albedo. In fact, differences in single scattering albedo have a significant impact on the magnitude of the cooling effect of aerosols (opposite to that of greenhouse gasses) which can even have a warming effect for strongly absorbing aerosols. Satellites provide a unique opportunity to measure aerosol properties on a global scale. Traditional approaches use multispectral measurements of intensity at a single view angle to retrieve at most two aerosol parameters over land but it is being realized that more detail is required for accurate quantification of the direct effect of aerosols, in particular its anthropogenic component, and therefore more measurement information is required. One approach to more advanced measurements is to use not only intensity measurements but also polarimetric measurements and to use multiple view angles. In this work we explore another alternative: the use of hyperspectral measurements in molecular absorption bands. Our study can be divided into three stages the first of which is the development of a fast radiative transfer model for rapid simulation of measurements. Our approach is matrix operator based and uses the Pade approximation for the matrix exponential to evaluate the homogeneous solution. It is shown that the method is two to four times faster than the standard and efficient discrete ordinate technique and is accurate to the 6th decimal place. The second part of our study forms the core and is divided into two chapters the first of which is a rigorous

  9. Mapping mine tailings using airborne geophysical and hyperspectral remote sensing data

    NASA Astrophysics Data System (ADS)

    Shang, Jiali

    Mine tailings are the waste products from mining operations. Most mine tailings contain a considerable amount of reactive sulphides which can cause acid mine drainage (AMD) when exposed to air and water. AMD constitutes a threat both to the environment and to public health. Increased awareness of AMD has led to growing activities in mine-tailing monitoring and reclamation worldwide. Mining companies in Canada are required to provide information to provincial governments about their waste disposal and control activities. There is an urgent need to develop new automated ways to provide information on short- to long-term evolution of tailings, thus enabling the mining companies to monitor their tailings more effectively. The overall goal of the thesis is to explore the potential of hyperspectral remote sensing and geophysical techniques for mapping variations within and immediately outside of the tailings. Data used for this study are from three sources: airborne geophysical data, hyperspectral casi and Probe-1 data, and field data. This study has contributed to both the remote sensing data analysis techniques and the understanding of mine-tailing surface and subsurface processes. Specifically, this study has the following important findings: (1) Airborne magnetic and electromagnetic data can provide information regarding the subsurface distribution of mine tailings on the basis of sulphide mineral content. A procedure has been developed in this study to use these data sources for rapidly surveying large tailings areas. This procedure can minimize expenditures for mining companies when designing remedial plans for the closure of the mines. This study has also identified regions of enhanced conductivity that extend beyond the tailing containment area. This information indicates seepage pathways, and is important for monitoring the effectiveness of tailing containment structures. (2) High-spatial-resolution hyperspectral casi (Compact Airborne Spectrographic Imagery

  10. Evaluation of the dark-object subtraction technique for adjustment of multispectral remote-sensing data

    NASA Astrophysics Data System (ADS)

    Campbell, James B.

    1993-03-01

    The well-known dark-object subtraction method has formed one of the oldest and widely used procedures for adjusting digital remote sensing data for effects of atmospheric scattering. The method's limited capabilities, relative to more sophisticated methods, are at least partially offset by its wide applicability, due its requirement for little information beyond the image itself. This study examines alternative applications of the procedure to evaluate its effectiveness, using a SPOT HRV XS image of irregular terrain in southwestern Virginia and a sequence of Landsat MSS data depicting a region in south central Virginia. Assessment of the success of the adjustment is conducted using chromaticity co-ordinates (using the method of Alfoldi and Munday (1978)), from corrected values, and comparing corrections to the original data. A successful correction shifts chromaticity co-ordinates away from the equal radiance point towards the purer regions near edges of the diagram. Further, some categories, when corrected successfully, will occupy known positions within chromaticity space. Assessment of the modification proposed by Chavez (1988) was conducted by examining the effects of choosing alternative starting haze values, and effects of alternative choices for atmospheric models. One difficulty in applying the 1988 modification is that it appears to be difficult to make accurate assessments of atmospheric conditions.

  11. Hyperspectral narrowband and multispectral broadband indices for remote sensing of crop evapotranspiration and its components (transpiration and soil evaporation)

    USGS Publications Warehouse

    Marshall, Michael T.; Thenkabail, Prasad S.; Biggs, Trent; Post, Kirk

    2016-01-01

    Evapotranspiration (ET) is an important component of micro- and macro-scale climatic processes. In agriculture, estimates of ET are frequently used to monitor droughts, schedule irrigation, and assess crop water productivity over large areas. Currently, in situ measurements of ET are difficult to scale up for regional applications, so remote sensing technology has been increasingly used to estimate crop ET. Ratio-based vegetation indices retrieved from optical remote sensing, like the Normalized Difference Vegetation Index (NDVI), Soil Adjusted Vegetation Index, and Enhanced Vegetation Index are critical components of these models, particularly for the partitioning of ET into transpiration and soil evaporation. These indices have their limitations, however, and can induce large model bias and error. In this study, micrometeorological and spectroradiometric data collected over two growing seasons in cotton, maize, and rice fields in the Central Valley of California were used to identify spectral wavelengths from 428 to 2295 nm that produced the highest correlation to and lowest error with ET, transpiration, and soil evaporation. The analysis was performed with hyperspectral narrowbands (HNBs) at 10 nm intervals and multispectral broadbands (MSBBs) commonly retrieved by Earth observation platforms. The study revealed that (1) HNB indices consistently explained more variability in ET (ΔR2 = 0.12), transpiration (ΔR2 = 0.17), and soil evaporation (ΔR2 = 0.14) than MSBB indices; (2) the relationship between transpiration using the ratio-based index most commonly used for ET modeling, NDVI, was strong (R2 = 0.51), but the hyperspectral equivalent was superior (R2 = 0.68); and (3) soil evaporation was not estimated well using ratio-based indices from the literature (highest R2 = 0.37), but could be after further evaluation, using ratio-based indices centered on 743 and 953 nm (R2 = 0.72) or 428 and 1518 nm (R2 = 0.69).

  12. Remote Sensing of Snow-covered Sea Ice with Ultra-wideband Airborne Radars

    NASA Astrophysics Data System (ADS)

    Yan, S.; Gogineni, P. S.; Gomez-Garcia, D.; Leuschen, C.; Hale, R.; Rodriguez-Morales, F.; Paden, J. D.; Li, J.

    2015-12-01

    The extent and thickness of sea ice and snow play a critical role in the Earth's climate system. Both sea ice and snow have high albedo and control the heat exchange between the atmosphere and ocean and atmosphere and land. In terms of hydrology, the presence of sea ice and snow modulates the flow and the salinity of ocean water. This in turn can modify the weather patterns around the globe. Understanding the formation, coverage and the properties of sea ice and snow are important for both short-term and long-term climate modeling. The advancements in high-frequency electronics and digital signal processing enabled the development of ultra-wideband radars by the Center for Remote Sensing of Ice Sheets (CReSIS) for airborne measurements of snow and ice properties over large areas. CReSIS recently developed and deployed two ultra-wideband airborne radars, namely the Multichannel Coherent Radar Depth Sounder/Imager (MCoRDS/I) and the Snow Radar. The MCoRDS/I is designed to operate over the frequency range of 180-450 MHz for sounding land ice and imaging its ice-bed interface. We also took advantage of the deployment to explore the potential of UWB MCoRDS/I in sounding sea ice and collected data on flight lines flown as part of NASA Operation IceBridge mission during Spring 2015. Preliminary results show we sounded sea ice under favorable conditions. We will perform detailed processing and analysis of data over the next few months and we will compare results obtained are compared with existing altimetry-derived data products. The new snow radar, on the other hand, operating from 2 to 18 GHz, was deployed on the NRL Twin Otter aircraft in Barrow, AK. It was shown to have a vertical resolution of down to 1.5 cm which opens up the potential for thin snow measurement on both sea ice and land. Both of these new radars will be further optimized for future airborne missions to demonstrate their capabilities for sea ice and snow measurements. We will also show new technical

  13. The research of a gyro-stabilized platform and POS application technology in airborne remote sensing

    NASA Astrophysics Data System (ADS)

    Xu, Jiang; Du, Qi

    2009-07-01

    The distortion of the collected images usually takes place since the attitude changes along with the flying aerocraft on airborne remote sensing. In order to get original images without distortion, it is necessary to use professional gyro-stabilized platform. In addition to this, another solution of correcting the original image distortion is to utilize later geometric rectification using position & orientation system ( POS ) data. The third way is to utilize medium-accuracy stabilized platform to control the distortion at a tolerant range, and then make use of the data obtained by high-solution posture measure system to correct the low-quality remote sensing images. The third way which takes advantage of both techniques is better than using only one of the two other ways. This paper introduces several kinds of structural forms of gyro-stabilized platforms, and POS acquiring instruments respectively. Then, the essay will make some analysis of their advantages and disadvantages, key technologies and the application experiment of the third method. After the analysis, the thesis discusses the design of the gyro-stabilized platform. The thesis provides crucial information not only for the application technology of gyro-stabilized platform and POS but also for future development.

  14. Application of high spatial resolution airborne hyperspectral remote sensing data in thematic information extraction

    NASA Astrophysics Data System (ADS)

    Xu, Hong-gen; Ma, Hong-chao; Li, De-ren; Song, Yan

    2006-10-01

    The airborne hyperspectral remote sensing data, such as PHI, OMIS, has the virtues of high spatial and spectral resolution. Hence, from the view of target classification we can consider that it can provide the ability of discriminating targets more detailedly than other data. So it's important to extract thematic information and update database using this kind of data. Whereas, the hyperspectral data has abundant bands and high between-band correlation, the traditional classification methods such as maximum likelihood classifier (MLC) and spectral angle mapper (SAM) have performed poorly in thematic information extraction. For this reason, we present a new method for thematic information extraction with hyperspectral remote sensing data. We perform classification by means of combining the self-organizing map (SOM) neural network which is considered as full-pixel technique with linear spectral mixture analysis (LSMA) which is considered as mixed-pixel technique. The SOM neural network is improved from some aspects to classify the pure data and find the mixed data. And then the mixed data are unmixed and classified by LSMA. The result of experiment shows that we can have the better performance in thematic information extraction with PHI by this means.

  15. Airborne and satellite remote sensing of the mid-infrared water vapour continuum.

    PubMed

    Newman, Stuart M; Green, Paul D; Ptashnik, Igor V; Gardiner, Tom D; Coleman, Marc D; McPheat, Robert A; Smith, Kevin M

    2012-06-13

    Remote sensing of the atmosphere from space plays an increasingly important role in weather forecasting. Exploiting observations from the latest generation of weather satellites relies on an accurate knowledge of fundamental spectroscopy, including the water vapour continuum absorption. Field campaigns involving the Facility for Airborne Atmospheric Measurements research aircraft have collected a comprehensive dataset, comprising remotely sensed infrared radiance observations collocated with accurate measurements of the temperature and humidity structure of the atmosphere. These field measurements have been used to validate the strength of the infrared water vapour continuum in comparison with the latest laboratory measurements. The recent substantial changes to self-continuum coefficients in the widely used MT_CKD (Mlawer-Tobin-Clough-Kneizys-Davies) model between 2400 and 3200 cm(-1) are shown to be appropriate and in agreement with field measurements. Results for the foreign continuum in the 1300-2000 cm(-1) band suggest a weak temperature dependence that is not currently included in atmospheric models. A one-dimensional variational retrieval experiment is performed that shows a small positive benefit from using new laboratory-derived continuum coefficients for humidity retrievals. PMID:22547235

  16. Airborne Thermal Remote Sensing for Estimation of Groundwater Discharge to a River.

    PubMed

    Liu, Chuankun; Liu, Jie; Hu, Yue; Wang, Heshun; Zheng, Chunmiao

    2016-05-01

    Traditional methods for studying surface water and groundwater interactions have usually been limited to point measurements, such as geochemical sampling and seepage measurement. A new methodology is presented for quantifying groundwater discharge to a river, by using river surface temperature data obtained from airborne thermal infrared remote sensing technology. The Hot Spot Analysis toolkit in ArcGIS was used to calculate the percentage of groundwater discharge to a river relative to the total flow of the river. This methodology was evaluated in the midstream of the Heihe River in the arid and semiarid northwest China. The results show that the percentage of groundwater discharge relative to the total streamflow was as high as 28%, which is in good agreement with the results from previous geochemical studies. The data analysis methodology used in this study is based on the assumption that the river water is fully mixed except in the areas of extremely low flow velocity, which could lead to underestimation of the amount of groundwater discharge. Despite this limitation, this remote sensing-based approach provides an efficient means of quantifying the surface water and groundwater interactions on a regional scale. PMID:26281027

  17. Remote sensing of tropospheric gases and aerosols with airborne DIAL system

    NASA Technical Reports Server (NTRS)

    Browell, E. V.

    1983-01-01

    The multipurpose airborne DIAL system developed at NASA Langley Research Center is characterized, and the published results of tropospheric O3, H2O, and aerosol-backscatter remote-sensing experiments performed in 1980 and 1981 are summarized. The system comprises two tunable dye lasers pumped by frequency-doubled Nd:YAG lasers, dielectric-coated steering optics, a 36-cm-diameter Cassegrain receiver telescope, gateable photomultiplier tubes, and a minicomputer data-processing unit for real-time calculation of gas concentrations and backscattering profiles. The transmitted energy of the 100-microsec-separated dye-laser pulses is 40, 80, or 50 mJ/pulse at around 300, 600, or 720-nm wavelength, respectively. Good agreement was found between DIAL-remote-sensed and in-situ H2O and O3 profiles of the lower troposphere and O3 profiles of the tropopause region, and the usefulness of DIAL backscattering measurements in the study of boundary-layer and tropospheric dynamics is demonstrated. The feasibility of DIAL sensing of power-plant or urban plume SO2, of urban-area (or rural-area column-content) NO2, and of temperature and H2O (simultaneously using a third laser) has been suggested by simulation studies.

  18. An Airborne A-Band Spectrometer for Remote Sensing Of Aerosol and Cloud Optical Properties

    NASA Technical Reports Server (NTRS)

    Pitts, Michael; Hostetler, Chris; Poole, Lamont; Holden, Carl; Rault, Didier

    2000-01-01

    Atmospheric remote sensing with the O2 A-band has a relatively long history, but most of these studies were attempting to estimate surface pressure or cloud-top pressure. Recent conceptual studies have demonstrated the potential of spaceborne high spectral resolution O2 A-band spectrometers for retrieval of aerosol and cloud optical properties. The physical rationale of this new approach is that information on the scattering properties of the atmosphere is embedded in the detailed line structure of the O2 A-band reflected radiance spectrum. The key to extracting this information is to measure the radiance spectrum at very high spectral resolution. Instrument performance requirement studies indicate that, in addition to high spectral resolution, the successful retrieval of aerosol and cloud properties from A-band radiance spectra will also require high radiometric accuracy, instrument stability, and high signal-to-noise measurements. To experimentally assess the capabilities of this promising new remote sensing application, the NASA Langley Research Center is developing an airborne high spectral resolution A-band spectrometer. The spectrometer uses a plane holographic grating with a folded Littrow geometry to achieve high spectral resolution (0.5 cm-1) and low stray light in a compact package. This instrument will be flown in a series of field campaigns beginning in 2001 to evaluate the overall feasibility of this new technique. Results from these campaigns should be particularly valuable for future spaceborne applications of A-band spectrometers for aerosol and cloud retrievals.

  19. Wetlands mapping with spot multispectral scanner data

    SciTech Connect

    Mackey, H.E. Jr. ); Jensen, J.R. . Dept. of Geography)

    1989-01-01

    Government facilities such as the US Department of Energy's Savannah River Plant (SRP) near Aiken, South Carolina, often use remote sensing data to assist in environmental management. Airborne multispectral scanner (MSS) data have been acquired at SRP since 1981. Various types of remote sensing data have been used to map and characterize wetlands. Regional Landsat MSS and TM satellite data have been used for wetlands mapping by various government agencies and private organizations. Furthermore, SPOT MSS data are becoming available and provide opportunities for increased spacial resolution and temporal coverage for wetlands mapping. This paper summarizes the initial results from using five dates of SPOT MSS data from April through October, 1987, as a means to monitor seasonal wetland changes in freshwater wetlands of the SRP. 11 refs., 4 figs.

  20. Remote Sensing of Vegetation Species Diversity: The Utility of Integrated Airborne Hyperspectral and Lidar Data

    NASA Astrophysics Data System (ADS)

    Krause, Keith Stuart

    The change, reduction, or extinction of species is a major issue currently facing the Earth. Efforts are underway to measure, monitor, and protect habitats that contain high species diversity. Remote sensing technology shows extreme value for monitoring species diversity by mapping ecosystems and using those land cover maps or other derived data as proxies to species number and distribution. The National Ecological Observatory Network (NEON) Airborne Observation Platform (AOP) consists of remote sensing instruments such as an imaging spectrometer, a full-waveform lidar, and a high-resolution color camera. AOP collected data over the Ordway-Swisher Biological Station (OSBS) in May 2014. A majority of the OSBS site is covered by the Sandhill ecosystem, which contains a very high diversity of vegetation species and is a native habitat for several threatened fauna species. The research presented here investigates ways to analyze the AOP data to map ecosystems at the OSBS site. The research attempts to leverage the high spatial resolution data and study the variability of the data within a ground plot scale along with integrating data from the different sensors. Mathematical features are derived from the data and brought into a decision tree classification algorithm (rpart), in order to create an ecosystem map for the site. The hyperspectral and lidar features serve as proxies for chemical, functional, and structural differences in the vegetation types for each of the ecosystems. K-folds cross validation shows a training accuracy of 91%, a validation accuracy of 78%, and a 66% accuracy using independent ground validation. The results presented here represent an important contribution to utilizing integrated hyperspectral and lidar remote sensing data for ecosystem mapping, by relating the spatial variability of the data within a ground plot scale to a collection of vegetation types that make up a given ecosystem.

  1. Scanning infrared remote sensing system for identification, visualization, and quantification of airborne pollutants

    NASA Astrophysics Data System (ADS)

    Harig, Roland; Matz, Gerhard; Rusch, Peter

    2002-02-01

    Remote sensing by Fourier-transform infrared (FTIR) spectrometry allows detection, identification, and quantification of airborne pollutants. In the case of leaks in pipelines or leaks in chemical plants, chemical accidents, terrorism, or war, hazardous compounds are often released into the atmosphere. Various Fourier-transform infrared spectrometers have been developed for the remote detection and identification of hazardous clouds. However, for the localization of a leak and a complete assessment of the situation in the case of the release of a hazardous cloud, information about the position and the size of a cloud is essential. Therefore, an imaging passive remote sensing system comprised of an interferometer (Bruker OPAG 22), a data acquisition, processing, and control system with a digital signal processor (FTIR DSP), an azimuth-elevation-scanning mirror, a video system with a DSP, and a personal computer has been developed. The FTIR DSP system controls the scanning mirror, collects the interferograms, and performs the Fourier transformation. The spectra are transferred to a personal computer and analyzed by a real-time identification algorithm that does not require background spectra for the analysis. The results are visualized by a video image, overlaid by false color images. For each target compound of a spectral library, images of the coefficient of correlation, the signal to noise ratio, the brightness temperature of the background, the difference between the temperature of the ambient air and the brightness temperature of the background, and the noise equivalent column density are produced. The column densities of all directions in which a target compound has been identified may be retrieved by a nonlinear least squares fitting algorithm and an additional false color image is displayed. The system has a high selectivity, low noise equivalent spectral radiance, and it allows identification, visualization, and quantification of pollutant clouds.

  2. An Open Source Software and Web-GIS Based Platform for Airborne SAR Remote Sensing Data Management, Distribution and Sharing

    NASA Astrophysics Data System (ADS)

    Changyong, Dou; Huadong, Guo; Chunming, Han; Ming, Liu

    2014-03-01

    With more and more Earth observation data available to the community, how to manage and sharing these valuable remote sensing datasets is becoming an urgent issue to be solved. The web based Geographical Information Systems (GIS) technology provides a convenient way for the users in different locations to share and make use of the same dataset. In order to efficiently use the airborne Synthetic Aperture Radar (SAR) remote sensing data acquired in the Airborne Remote Sensing Center of the Institute of Remote Sensing and Digital Earth (RADI), Chinese Academy of Sciences (CAS), a Web-GIS based platform for airborne SAR data management, distribution and sharing was designed and developed. The major features of the system include map based navigation search interface, full resolution imagery shown overlaid the map, and all the software adopted in the platform are Open Source Software (OSS). The functions of the platform include browsing the imagery on the map navigation based interface, ordering and downloading data online, image dataset and user management, etc. At present, the system is under testing in RADI and will come to regular operation soon.

  3. Remote sensing of wetlands

    NASA Technical Reports Server (NTRS)

    Roller, N. E. G.

    1977-01-01

    The concept of using remote sensing to inventory wetlands and the related topics of proper inventory design and data collection are discussed. The material presented shows that aerial photography is the form of remote sensing from which the greatest amount of wetlands information can be derived. For extensive, general-purpose wetlands inventories, however, the use of LANDSAT data may be more cost-effective. Airborne multispectral scanners and radar are, in the main, too expensive to use - unless the information that these sensors alone can gather remotely is absolutely required. Multistage sampling employing space and high altitude remote sensing data in the initial stages appears to be an efficient survey strategy for gathering non-point specific wetlands inventory data over large areas. The operational role of remote sensing insupplying inventory data for application to several typical wetlands management problems is illustrated by summary descriptions of past ERIM projects.

  4. Developing a Scalable Remote Sampling Design for the NEON Airborne Observation Platform (AOP)

    NASA Astrophysics Data System (ADS)

    Musinsky, J.; Wasser, L. A.; Kampe, T. U.; Leisso, N.; Krause, K.; Petroy, S. B.; Cawse-Nicholson, K.; van Aardt, J. A.; Serbin, S.

    2013-12-01

    The National Ecological Observatory Network (NEON) airborne observation platform (AOP) will collect co-registered high-resolution hyperspectral imagery, discrete and waveform LiDAR, and high-resolution digital photography for more than 60 terrestrial and 23 aquatic sites spread across the continental United States, Puerto Rico, Alaska and Hawaii on an annual basis over the next 30 years. These data, to be made freely available to the public, will facilitate the scaling of field-based biological, physical and chemical measurements to regional and continental scales, enabling a better understanding of the relationships between climate variability and change, land use change and invasive species, and their ecological consequences in areas not directly sampled by the NEON facilities. However, successful up-scaling of in situ measurements requires a flight sampling design that captures environmental heterogeneity and diversity (i.e., ecological and topographic gradients), is sensitive to temporal system variation (e.g., phenology), and can respond to major disturbance events. Alignment of airborne campaigns - composed of two payloads for nominal science acquisitions and one payload for PI-driven rapid-response campaigns -- with other ground, airborne (e.g., AVIRIS) and satellite (e.g., Landsat, MODIS) collections will further facilitate scaling between sensors and data sources of varying spatial and spectral resolution and extent. This presentation will discuss the approach, challenges and future goals associated with the development of NEON AOP's sampling design, using examples from the 2013 nominal flight campaigns in the Central Plains (NEON Domain 10) and the Pacific Southwest (Domain 17), and the rapid response flight campaign of the High Park Fire site outside of Fort Collins, CO. Determination of the specific flight coverage areas for each campaign involved analysis of the landscape scale ecological, geophysical and bioclimatic attributes and trends most closely

  5. Multi-resolution processing for fractal analysis of airborne remotely sensed data

    NASA Technical Reports Server (NTRS)

    Jaggi, S.; Quattrochi, D.; Lam, N.

    1992-01-01

    Fractal geometry is increasingly becoming a useful tool for modeling natural phenomenon. As an alternative to Euclidean concepts, fractals allow for a more accurate representation of the nature of complexity in natural boundaries and surfaces. Since they are characterized by self-similarity, an ideal fractal surface is scale-independent; i.e. at different scales a fractal surface looks the same. This is not exactly true for natural surfaces. When viewed at different spatial resolutions parts of natural surfaces look alike in a statistical manner and only for a limited range of scales. Images acquired by NASA's Thermal Infrared Multispectral Scanner are used to compute the fractal dimension as a function of spatial resolution. Three methods are used to determine the fractal dimension - Schelberg's line-divider method, the variogram method, and the triangular prism method. A description of these methods and the results of applying these methods to a remotely-sensed image is also presented. Five flights were flown in succession at altitudes of 2 km (low), 6 km (mid), 12 km (high), and then back again at 6 km and 2 km. The area selected was the Ross Barnett reservoir near Jackson, Mississippi. The mission was flown during the predawn hours of 1 Feb. 1992. Radiosonde data was collected for that duration to profile the characteristics of the atmosphere. This corresponds to 3 different pixel sizes - 5m, 15m, and 30m. After, simulating different spatial sampling intervals within the same image for each of the 3 image sets, the results are cross-correlated to compare the extent of detail and complexity that is obtained when data is taken at lower spatial intervals.

  6. Atmospheric correction for ocean spectra retrievals from high-altitude multi-angle, multi-spectral photo-polarimetric remote sensing observations: Results for coastal ocean waters.

    NASA Astrophysics Data System (ADS)

    Chowdhary, J.; van Diedenhoven, B.; Knobelspiesse, K. D.; Cairns, B.; Wasilewski, A. P.; McCubbin, I.

    2015-12-01

    A major challenge for spaceborne observations of ocean color is to correct for atmospheric scattering, which typically contributes ≥85% to the top-of-atmosphere (TOA) radiance and varies substantially with aerosols. Ocean color missions traditionally analyze TOA radiance in the near-infrared (NIR), where the ocean is black, to constrain the TOA atmospheric scattering in the visible (VIS). However, this procedure is limited by insufficient sensitivity of NIR radiance to absorption and vertical distribution of aerosols, and by uncertainties in the extrapolation of aerosol properties from the NIR to the VIS.To improve atmospheric correction for ocean color observations, one needs to change the traditional procedure for this correction and/or increase the aerosol information. The instruments proposed to increase the aerosol information content for the Pre-Aerosol, Clouds, and ocean Ecosystem (PACE) mission include ultraviolet and Oxygen A-band observations, as well as multispectral and multiangle polarimetry. However few systematic studies have been performed to quantify the improvement such measurements bring to atmospheric correction. To study the polarimetric atmospheric correction capabilities of PACE-like instruments, we conducted field experiments off the Coast of California to obtain high-altitude (65,000 ft) and ship-based observations of water-leaving radiance. The airborne data sets consist of hyperspectral radiance between 380-2500 nm by the Airborne Visible/Infrared Imaging Spectrometer, and multi-spectral multi-angle polarimetric data between 410-2250 nm by the Research Scanning Polarimeter. We discuss examples of retrieved atmosphere and ocean state vectors, and of corresponding ocean color spectra obtained by subtracting the computed atmospheric scattering contribution from the high-altitude radiance measurements. The ocean color spectra thus obtained are compared with those measured from the ship.

  7. Investigation of atmospheric insect wing-beat frequencies and iridescence features using a multi-spectral kHz remote detection system

    NASA Astrophysics Data System (ADS)

    Gebru, Alem; Rohwer, Erich; Neethling, Pieter; Brydegaard, Mikkel

    2014-10-01

    Quantitative investigation of insect activity in their natural habitat is a challenging task for entomologist. It is difficult to address questions such as flight direction, predation strength and overall activities using the current techniques such as traps and sweep nets. A multi-spectral kHz remote detection system using sunlight as an illumination source is presented. We explore possibilities of remote optical classification of insects based on their wing-beat frequencies and iridescence features. It is shown that the wing-beat frequency of the fast insect events can be resolved by implementing high sampling frequency. The iridescence features generated from the change of color in two channels (visible and near infrared) during wing-beat cycle is presented. We show that the shape of the wing-beat trajectory is different for different insects. The flight direction of atmospheric insect is also determined using silicon quadrant detector.

  8. Multispectral Thermal Infrared Remote Sensing of Volcanic SO2 Plumes with NASA’s Earth Observing System

    NASA Astrophysics Data System (ADS)

    Realmuto, V. J.

    2009-12-01

    The instruments aboard NASA’s series of Earth Observing System satellites provide a rich suite of measurements for the mapping of volcanic plumes and clouds. This presentation will focus on applications of thermal multispectral infrared (TIR) data acquired with the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER), Moderate-Resolution Imaging Spectrometer (MODIS), and Atmospheric Infrared Sounder (AIRS) to the recent eruptions of Augustine and Sarychev volcanoes in Alaska and the Russian Kuril Islands, respectively. ASTER, MODIS, and AIRS provide complimentary information on the quantity and distribution of sulfur dioxide (SO2), silicate ash, and sulfate (SO4) aerosols within plumes. In addition, data from the Multi-angle Imaging SpectroRadiometer (MISR) are used to derive estimates of aerosol loading, cloud-top altitude, wind direction, and wind speed. MODIS is our workhorse for plume mapping projects. There are MODIS instruments on the Terra and Aqua platforms, ensuring at least two MODIS passes per day over most volcanoes and four passes per day over many volcanoes. The spatial resolution of MODIS TIR radiance measurements is 1 km (at nadir) over a ground swath of 2330 km. MODIS can detect both the 7.3 and 8.5 μm bands of SO2, although the 7.3 μm band is often obscured by water vapor absorption when plumes are altitudes below ~ 4 km. ASTER has five channels in the TIR, and can detect the 8.5 μm SO2 band. The high spatial resolution (90 m) of ASTER TIR radiance measurements results in high sensitivity to SO2 within a narrow ground swath (60 km). AIRS has over 2700 spectral channels between 3.7 and 15.4 μm, allowing us to make unambiguous identifications of SO2, SO4 aerosols, and ash over a ground swath of ~2330 km. AIRS can detect the 7.3 μm SO2 band, and the strength of this band partially offsets the coarse spatial resolution of this instrument (~17 km at nadir). The key to multi-sensor mapping is the availability of a standard set

  9. Optical design of high resolution and large format CCD airborne remote sensing camera on unmanned aerial vehicle

    NASA Astrophysics Data System (ADS)

    Qian, Yixian; Cheng, Xiaowei; Shao, Jie

    2010-11-01

    Unmanned aerial vehicle remote sensing (UAVRS) is lower in cost, flexible on task arrangement and automatic and intelligent in application, it has been used widely for mapping, surveillance, reconnaissance and city planning. Airborne remote sensing missions require sensors with both high resolution and large fields of view, large format CCD digital airborne imaging systems are now a reality. A refractive system was designed to meet the requirements with the help of code V software, It has a focal length of 150mm, F number of 5.6, waveband of 0.45~0.7um, and field of view reaches 20°. It is shown that the value of modulation transfer function is higher than 0.5 at 55lp/mm, distortion is less than 0.1%, image quality reaches the diffraction limit. The system with large format CCD and wide field can satisfy the demand of the wide ground overlay area and high resolution. The optical system with simpler structure, smaller size and lighter weight, can be used in airborne remote sensing.

  10. A Nadir-adjusted Airborne Multi Spectral Imaging System (NAMSIS) for high-resolution remote sensing of carbon fluxes

    NASA Astrophysics Data System (ADS)

    Jiang, Z.; Scott, S.; Rahman, A. F.

    2012-12-01

    Satellite remote sensing is widely used in vegetation monitoring, water stress detection and carbon cycle modeling. However, image pixels from high temporal resolution satellite sensors (such as MODIS) have coarse spatial resolution, much larger than the canopies they are supposed to characterize. An alternative solution for on-demand high spatial resolution remote sensing is sensors onboard low-flying aircrafts. Airborne remote sensing has been traditionally used in crop management studies. In this presentation we demonstrate the application of a relatively low-cost airborne sensor system with customized spectral band combinations for studying forest carbon fluxes. Our team has developed an Inertia Measurement Unit (IMU) controlled automated system to detach aircraft movements (pitch and roll) and engine vibration from the six-band programmable imager, in order to maintain the sensor at nadir view at all times during the flight. Flight lines are configured by a GPS-controleld system to simulate MODIS pixels. A feature-based algorithm is used to automatically generate a mosaic of individual images along the flight lines. This algorithm eliminates the need to mosiac and georeference images manually. An empirical line method is used to calculate reflectance from the raw data. Images from this airborne system produce reflectance values that are comparable with MODIS reflectance product. These high spatial resolution (~0.5 m) images deliver detailed information about tree species and phenological conditions within each MODIS pixel, and thus permit a high resolution spatio-temporal assessment of forest carbon fluxes.

  11. Remote tree species identification in a diverse tropical forest using airborne imaging spectroscopy

    NASA Astrophysics Data System (ADS)

    Baldeck, C.; Asner, G. P.; Kellner, J. R.; Martin, R.; Anderson, C.; Knapp, D. E.

    2013-12-01

    Plant species identification and mapping based on remotely-sensed spectral signatures is a challenging task with the potential to contribute enormously to ecological studies. This task is especially difficult in highly diverse ecosystems such as tropical forests, and for these ecosystems it may be more strategic to direct efforts to identifying crowns of a focal species. We used imaging spectrometer data collected by the Carnegie Airborne Observatory over Barro Colorado Island, Panama, to develop classification models for the identification of tree crowns belonging to selected focal species. We explored alternative methods for detecting crowns of focal species, which included binary, one-class, and biased support vector machines (SVM). Best performance was given by binary and biased SVM, with poor performance observed for one-class SVM. Binary and biased SVM were able to identify crowns of focal species with classification sensitivity and specificity of 87-91% and 89-94%, respectively. The main tradeoff between binary and biased SVM is that construction of binary SVM requires a far greater amount of training data while biased SVM is more difficult to parameterize. Our results show that with sufficient training data, focal species can be mapped with a high degree of accuracy, in terms of both sensitivity and specificity, in this diverse tropical forest.

  12. Remote detection of water stress in orchard canopies using MODIS/ASTER airborne simulator (MASTER) data

    NASA Astrophysics Data System (ADS)

    Cheng, Tao; Riaño, David; Koltunov, Alexander; Whiting, Michael L.; Ustin, Susan L.

    2011-09-01

    Vegetation canopy water content (CWC) is an important parameter for monitoring natural and agricultural ecosystems. Previous studies focused on the observation of annual or monthly variations in CWC but lacked temporal details to study vegetation physiological activities within a diurnal cycle. This study provides an evaluation of detecting vegetation diurnal water stress using airborne data acquired with the MASTER instrument. Concurrent with the morning and afternoon acquisitions of MASTER data, an extensive field campaign was conducted over almond and pistachio orchards in southern San Joaquin Valley of California to collect CWC measurements. Statistical analysis of the field measurements indicated a significant decrease of CWC from morning to afternoon. Field measured CWC was linearly correlated to the normalized difference infrared index (NDII) calculated with atmospherically corrected MASTER reflectance data using either FLAASH or empirical line (EL). Our regression analysis demonstrated that both atmospheric corrections led to a root mean square error (RMSE) of approximately 0.035 kg/m2 for the estimation of CWC (R2=0.42 for FLAASH images and R2=0.45 for EL images). Remote detection of the subtle decline in CWC awaits an improved prediction of CWC. Diurnal CWC maps revealed the spatial patterns of vegetation water status in response to variations in irrigation treatment.

  13. Optical remote sensing of the earth

    NASA Technical Reports Server (NTRS)

    Goetz, A. F. H.; Wellman, J. B.; Barnes, W. L.

    1985-01-01

    In the present assessment of the contributions of optical earth resources remote sensing in the 0.4-15.0 micron region, attention is given to underlying principles, applications to scientific disciplines such as geology, hydrology and oceanography, the recent development history of the requisite sensors, and sensor development trends. Development status characterizations are given for thematic mapping, modular optoelectronic multispectral scanning, the telescope/CCD 'SPOT' program of France, the thermal IR multispectral scanner for mineral signature identification, airborne imaging spectrometry, and the Advanced Visible and IR Imaging Spectrometer that is nearing deployment. Technology development trends and the capabilities they portend are projected.

  14. [In-flight absolute radiometric calibration of UAV multispectral sensor].

    PubMed

    Chen, Wei; Yan, Lei; Gou, Zhi-Yang; Zhao, Hong-Ying; Liu, Da-Ping; Duan, Yi-Ni

    2012-12-01

    Based on the data of the scientific experiment in Urad Front Banner for UAV Remote Sensing Load Calibration Field project, with the help of 6 hyperspectral radiometric targets with good Lambertian property, the wide-view multispectral camera in UAV was calibrated adopting reflectance-based method. The result reveals that for green, red and infrared channel, whose images were successfully captured, the linear correlation coefficients between the DN and radiance are all larger than 99%. In final analysis, the comprehensive error is no more than 6%. The calibration results demonstrate that the hyperspectral targets equipped by the calibration field are well suitable for air-borne multispectral load in-flight calibration. The calibration result is reliable and could be used in the retrieval of geophysical parameters. PMID:23427528

  15. The NASA Airborne Earth Science Microwave Imaging Radiometer (AESMIR): A New Sensor for Earth Remote Sensing

    NASA Technical Reports Server (NTRS)

    Kim, Edward

    2003-01-01

    The Airborne Earth Science Microwave Imaging Radiometer (AESMIR) is a versatile new airborne imaging radiometer recently developed by NASA. The AESMIR design is unique in that it performs dual-polarized imaging at all standard passive microwave frequency bands (6-89 GHz) using only one sensor headscanner package, providing an efficient solution for Earth remote sensing applications (snow, soil moisture/land parameters, precipitation, ocean winds, sea surface temperature, water vapor, sea ice, etc.). The microwave radiometers themselves will incorporate state-of-the-art receivers, with particular attention given to instrument calibration for the best possible accuracy and sensitivity. The single-package design of AESMIR makes it compatible with high-altitude aircraft platforms such as the NASA ER-2s. The arbitrary 2-axis gimbal can perform conical and cross-track scanning, as well as fixed-beam staring. This compatibility with high-altitude platforms coupled with the flexible scanning configuration, opens up previously unavailable science opportunities for convection/precip/cloud science and co-flying with complementary instruments, as well as providing wider swath coverage for all science applications. By designing AESMIR to be compatible with these high-altitude platforms, we are also compatible with the NASA P-3, the NASA DC-8, C-130s and ground-based deployments. Thus AESMIR can provide low-, mid-, and high- altitude microwave imaging. Parallel filter banks allow AESMIR to simultaneously simulate the exact passbands of multiple satellite radiometers: SSM/I, TMI, AMSR, Windsat, SSMI/S, and the upcoming GPM/GMI and NPOESS/CMIS instruments --a unique capability among aircraft radiometers. An L-band option is also under development, again using the same scanner. With this option, simultaneous imaging from 1.4 to 89 GHz will be feasible. And, all receivers except the sounding channels will be configured for 4-Stokes polarimetric operation using high-speed digital

  16. CASI/SASI airborne hyperspectral remote sensing anomaly extraction of metallogenic prediction research in Gansu Beishan South Beach area

    NASA Astrophysics Data System (ADS)

    Che, Yongfei; Zhao, Yingjun

    2014-11-01

    Hyperspectral remote sensing has one of the technical advantages atlas. The known deposits of Gansu Beishan South Beach deposits as the study area, based on the theory of wall rock alteration, using airborne hyperspectral remote sensing data (CASI/SASI), extracted mineralization alteration information and analysis. Based on airborne hyperspectral remote sensing mineral mapping results in the study area, Combining analysising of possible mineral formation fluid properties, spatial distribution characteristics and time evolution with analysising of mineral formation environment (lithology and tectonic environment), construction of the South Beach gold deposit location model, the deposit location model as a guide, comprehensive analysis of mineralization geological background and surface geochemical data, delineated mineralization favorable areas. The field investigation showed that signs of altered development of strong in the delineation of the mineralization favorable areas and metallogenic potential of better, is worth paying attention to the prospecting target area. Further explanation that the hyperspectral remote sensing can provide accurate and reliable information for the prospecting, and is worthy of further mining the ore prospecting potential.

  17. Interpretation of multispectral and infrared thermal surveys of the Suez Canal Zone, Egypt

    NASA Technical Reports Server (NTRS)

    Elshazly, E. M.; Hady, M. A. A. H.; Hafez, M. A. A.; Salman, A. B.; Morsy, M. A.; Elrakaiby, M. M.; Alaassy, I. E. E.; Kamel, A. F.

    1977-01-01

    Remote sensing airborne surveys were conducted, as part of the plan of rehabilitation, of the Suez Canal Zone using I2S multispectral camera and Bendix LN-3 infrared passive scanner. The multispectral camera gives four separate photographs for the same scene in the blue, green, red, and near infrared bands. The scanner was operated in the microwave bands of 8 to 14 microns and the thermal surveying was carried out both at night and in the day time. The surveys, coupled with intensive ground investigations, were utilized in the construction of new geological, structural lineation and drainage maps for the Suez Canal Zone on a scale of approximately 1:20,000, which are superior to the maps made by normal aerial photography. A considerable number of anomalies belonging to various types were revealed through the interpretation of the executed multispectral and infrared thermal surveys.

  18. Contribution of space platforms to a ground and airborne remote sensing programme over active Italian volcanoes

    NASA Technical Reports Server (NTRS)

    Cassinis, R. (Principal Investigator); Lechi, G. M.; Marino, C. M.; Tonelli, A. M.

    1974-01-01

    The author has identified the following significant results. A method has been suggested for the forecasting of the lateral eruptions of Mount Etna, through the multispectral analysis of the vegetation behavior. Unknown geological lineaments which seem to be related to deep crustal movements have been discovered using the ERTS-1 imagery. Results in the geological field were obtained in the study of the general structure of the Alpine range. In the field of official vegetation classification, ERTS-1 images were used for a preliminary study of rice fields in northern Italy. Very good experimental results have been obtained using the Skylab multispectral photographs. In the field of hydrogeology and soil type discrimination discoveries of unknown paleoriver beds have been made in the northeastern part of the Po Valley using the multispectral imagery of SL3. The superior resolution of Skylab was a fundamental element for the success of this investigation.

  19. Use of airborne remote sensing to detect riverside Brassica rapa to aid in risk assessment of transgenic crops

    NASA Astrophysics Data System (ADS)

    Elliott, Luisa M.; Mason, David C.; Allainguillaume, Joel; Wilkinson, Mike J.

    2009-11-01

    High resolution descriptions of plant distribution have utility for many ecological applications but are especially useful for predictive modeling of gene flow from transgenic crops. Difficulty lies in the extrapolation errors that occur when limited ground survey data are scaled up to the landscape or national level. This problem is epitomized by the wide confidence limits generated in a previous attempt to describe the national abundance of riverside Brassica rapa (a wild relative of cultivated rapeseed) across the United Kingdom. Here, we assess the value of airborne remote sensing to locate B. rapa over large areas and so reduce the need for extrapolation. We describe results from flights over the river Nene in England acquired using Airborne Thematic Mapper (ATM) and Compact Airborne Spectrographic Imager (CASI) imagery, together with ground truth data. It proved possible to detect 97% of flowering B. rapa on the basis of spectral profiles. This included all stands of plants that occupied >2m square (>5 plants), which were detected using single-pixel classification. It also included very small populations (<5 flowering plants, 1-2m square) that generated mixed pixels, which were detected using spectral unmixing. The high detection accuracy for flowering B. rapa was coupled with a rather large false positive rate (43%). The latter could be reduced by using the image detections to target fieldwork to confirm species identity, or by acquiring additional remote sensing data such as laser altimetry or multitemporal imagery.

  20. Michigan experimental multispectral scanner system

    NASA Technical Reports Server (NTRS)

    Hasell, P. G., Jr.

    1972-01-01

    A functional description of a multispectral airborne scanner system that provides spectral bands along a single optical line of sight is reported. The airborne scanner consists of an optical telescope for scanning plane perpendicular to the longitudinal axis of the aircraft and radiation detectors for converting radiation to electrical signals. The system makes a linear transformation of input radiation to voltage recorded on analog magnetic tape.

  1. Icepod: A modular approach to the development of an airborne remote sensing and data acquisition platform

    NASA Astrophysics Data System (ADS)

    Frearson, N.; Bell, R. E.; Tinto, K. J.; Zappa, C. J.

    2013-12-01

    The New York Air National Guard [NYANG] provides regular airborne support to the National Science Foundation [NSF] moving science parties and their equipment onto and around the ice-sheets in both polar regions during the respective summer seasons. Icepod has been developed to utilize this readily available resource, providing the aircraft with a modular external pod attached to the rear-paratrooper door on either side of the NYANG's ski-equipped LC-130s. The pod is divided into five separate bays each approximately a 2ft cube within which can be mounted an array of remote sensors. Power, heating, sensor control and data management services are provided to each bay. An Ethernet network is used to transfer commands and data packets between the individual sensors and data acquisition system located inside the aircraft. Data for each sensor is stored on ruggedized and removable hard-drives that can be taken off the aircraft at the end of a flight for further analysis. In its current configuration the pod is equipped for the remote sensing of ice sheets and their margins and the bay's contain two radar systems, radar antennas, a vibration isolated optics bay including a scanning laser, Infra-red camera and high-definition visible wave camera. Sensor data is geo-referenced using GNSS and orientation sensors located inside the pod. A Pyrometer provides the downward looking IR Camera with the current sky temperature. In January 2013, the Icepod system was flight certified at the Stratton air base in Schenectady, New York. The system deployed to Greenland in April and July 2013 to test the instrumentation suite over ice and its ease of deployment with the NYANG. Icepod can be operated in two modes, a traditional dedicated science flight mode and a piggy-back mode. In piggy-back mode science parties and their cargo are delivered to their destinations with Icepod installed but stowed. Once they have been delivered the Icepod is deployed and measurements can be taken on the

  2. Vineyard zonal management for grape quality assessment by combining airborne remote sensed imagery and soil sensors

    NASA Astrophysics Data System (ADS)

    Bonilla, I.; Martínez De Toda, F.; Martínez-Casasnovas, J. A.

    2014-10-01

    Vineyard variability within the fields is well known by grape growers, producing different plant responses and fruit characteristics. Many technologies have been developed in last recent decades in order to assess this spatial variability, including remote sensing and soil sensors. In this paper we study the possibility of creating a stable classification system that better provides useful information for the grower, especially in terms of grape batch quality sorting. The work was carried out during 4 years in a rain-fed Tempranillo vineyard located in Rioja (Spain). NDVI was extracted from airborne imagery, and soil conductivity (EC) data was acquired by an EM38 sensor. Fifty-four vines were sampled at véraison for vegetative parameters and before harvest for yield and grape analysis. An Isocluster unsupervised classification in two classes was performed in 5 different ways, combining NDVI maps individually, collectively and combined with EC. The target vines were assigned in different zones depending on the clustering combination. Analysis of variance was performed in order to verify the ability of the combinations to provide the most accurate information. All combinations showed a similar behaviour concerning vegetative parameters. Yield parameters classify better by the EC-based clustering, whilst maturity grape parameters seemed to give more accuracy by combining all NDVIs and EC. Quality grape parameters (anthocyanins and phenolics), presented similar results for all combinations except for the NDVI map of the individual year, where the results were poorer. This results reveal that stable parameters (EC or/and NDVI all-together) clustering outcomes in better information for a vineyard zonal management strategy.

  3. Using High-Resolution Airborne Remote Sensing to Study Aerosol Near Clouds

    NASA Technical Reports Server (NTRS)

    Levy, Robert; Munchak, Leigh; Mattoo, Shana; Marshak, Alexander; Wilcox, Eric; Gao, Lan; Yorks, John; Platnick, Steven

    2016-01-01

    The horizontal space in between clear and cloudy air is very complex. This so-called twilight zone includes activated aerosols that are not quite clouds, thin cloud fragments that are not easily observable, and dying clouds that have not quite disappeared. This is a huge challenge for satellite remote sensing, specifically for retrieval of aerosol properties. Identifying what is cloud versus what is not cloud is critically important for attributing radiative effects and forcings to aerosols. At the same time, the radiative interactions between clouds and the surrounding media (molecules, surface and aerosols themselves) will contaminate retrieval of aerosol properties, even in clear skies. Most studies on aerosol cloud interactions are relevant to moderate resolution imagery (e.g. 500 m) from sensors such as MODIS. Since standard aerosol retrieval algorithms tend to keep a distance (e.g. 1 km) from the nearest detected cloud, it is impossible to evaluate what happens closer to the cloud. During Studies of Emissions, Atmospheric Composition, Clouds and Climate Coupling by Regional Surveys (SEAC4RS), the NASA ER-2 flew with the enhanced MODIS Airborne Simulator (eMAS), providing MODIS-like spectral observations at high (50 m) spatial resolution. We have applied MODIS-like aerosol retrieval for the eMAS data, providing new detail to characterization of aerosol near clouds. Interpretation and evaluation of these eMAS aerosol retrievals is aided by independent MODIS-like cloud retrievals, as well as profiles from the co-flying Cloud Physics Lidar (CPL). Understanding aerosolcloud retrieval at high resolution will lead to better characterization and interpretation of long-term, global products from lower resolution (e.g.MODIS) satellite retrievals.

  4. Synthesis of Multispectral Bands from Hyperspectral Data: Validation Based on Images Acquired by AVIRIS, Hyperion, ALI, and ETM+

    NASA Technical Reports Server (NTRS)

    Blonksi, Slawomir; Gasser, Gerald; Russell, Jeffrey; Ryan, Robert; Terrie, Greg; Zanoni, Vicki

    2001-01-01

    Multispectral data requirements for Earth science applications are not always studied rigorously studied before a new remote sensing system is designed. A study of the spatial resolution, spectral bandpasses, and radiometric sensitivity requirements of real-world applications would focus the design onto providing maximum benefits to the end-user community. To support systematic studies of multispectral data requirements, the Applications Research Toolbox (ART) has been developed at NASA's Stennis Space Center. The ART software allows users to create and assess simulated datasets while varying a wide range of system parameters. The simulations are based on data acquired by existing multispectral and hyperspectral instruments. The produced datasets can be further evaluated for specific end-user applications. Spectral synthesis of multispectral images from hyperspectral data is a key part of the ART software. In this process, hyperspectral image cubes are transformed into multispectral imagery without changes in spatial sampling and resolution. The transformation algorithm takes into account spectral responses of both the synthesized, broad, multispectral bands and the utilized, narrow, hyperspectral bands. To validate the spectral synthesis algorithm, simulated multispectral images are compared with images collected near-coincidentally by the Landsat 7 ETM+ and the EO-1 ALI instruments. Hyperspectral images acquired with the airborne AVIRIS instrument and with the Hyperion instrument onboard the EO-1 satellite were used as input data to the presented simulations.

  5. An Analysis of Applications Development Systems for Remotely Sensed, Multispectral Data for the Earth Observations Division of the NASA Lyndon B. Johnson Space Center

    NASA Technical Reports Server (NTRS)

    Vanrooy, D. L.; Smith, R. M.; Lynn, M. S.

    1974-01-01

    An application development system (ADS) is examined for remotely sensed, multispectral data at the Earth Observations Division (EOD) at Johnson Space Center. Design goals are detailed, along with design objectives that an ideal system should contain. The design objectives were arranged according to the priorities of EOD's program objectives. Four systems available to EOD were then measured against the ideal ADS as defined by the design objectives and their associated priorities. This was accomplished by rating each of the systems on each of the design objectives. Utilizing the established priorities, it was determined how each system stood up as an ADS. Recommendations were made as to possible courses of action for EOD to pursue to obtain a more efficient ADS.

  6. Airborne Sunphotometer Studies of Aerosol Properties and Effects, Including Closure Among Satellite, Suborbital Remote, and In situ Measurements

    NASA Technical Reports Server (NTRS)

    Russlee, Philip B.; Schmid, B.; Redemann, J.; Livingston, J. M.; Bergstrom, R. W.; Ramirez, S. A.; Hipskind, R. Stephen (Technical Monitor)

    2001-01-01

    Airborne sunphotometry has been used to measure aerosols from North America, Europe, and Africa in coordination with satellite and in situ measurements in TARFOX (1996), ACE-2 (1997), PRIDE (2000), and SAFARI 2000. Similar coordinated measurements of Asian aerosols are being conducted this spring in ACE-Asia and are planned for North American aerosols this summer in CLAMS. This paper summarizes the approaches used, key results, and implications for aerosol properties and effects, such as single scattering albedo and regional radiative forcing. The approaches exploit the three-dimensional mobility of airborne sunphotometry to access satellite scenes over diverse surfaces (including open ocean with and without sunglint) and to match exactly the atmospheric layers sampled by airborne in situ measurements and other radiometers. These measurements permit tests of the consistency, or closure, among such diverse measurements as aerosol size-resolved chemical composition; number or mass concentration; light extinction, absorption, and scattering (total, hemispheric back and 180 deg.); and radiative fluxes. In this way the airborne sunphotometer measurements provide a key link between satellite and in situ measurements that helps to understand any discrepancies that are found. These comparisons have led to several characteristic results. Typically these include: (1) Better agreement among different types of remote measurements than between remote and in situ measurements. (2) More extinction derived from transmission measurements than from in situ measurements. (3) Larger aerosol absorption inferred from flux radiometry than from in situ measurements. Aerosol intensive properties derived from these closure studies have been combined with satellite-retrieved fields of optical depth to produce fields of regional radiative forcing. We show results for the North Atlantic derived from AVHRR optical depths and aerosol intensive properties from TARFOX and ACE-2. Companion papers

  7. COMET: a planned airborne mission to simultaneously measure CO2 and CH4 columns using airborne remote sensing and in-situ techniques

    NASA Astrophysics Data System (ADS)

    Fix, A.; Amediek, A.; Büdenbender, C.; Ehret, G.; Wirth, M.; Quatrevalet, M.; Rapp, M.; Gerilowski, K.; Bovensmann, H.; Gerbig, C.; Pfeilsticker, K.; Zöger, M.; Giez, A.

    2013-12-01

    To better predict future trends in the cycles of the most important anthropogenic greenhouse gases, CO2 and CH4, there is a need to measure and understand their distribution and variation on various scales. To address these requirements it is envisaged to deploy a suite of state-of-the-art airborne instruments that will be capable to simultaneously measure the column averaged dry-air mixing ratios (XGHG) of both greenhouse gases along the flight path. As the measurement platform serves the research aircraft HALO, a modified Gulfstream G550, operated by DLR. This activity is dubbed CoMet (CO2 and Methane Mission). The instrument package of CoMet will consist of active and passive remote sensors as well as in-situ instruments to complement the column measurements by highly-resolved profile information. As an active remote sensing instrument CHARM-F, the integrated-path differential absorption lidar currently under development at DLR, will provide both, XCO2 and XCH4, below flight altitude. The lidar instrument will be complemented by MAMAP which is a NIR/SWIR absorption spectrometer developed by University of Bremen and which is also capable to derive XCH4 and XCO2. As an additional passive instrument, mini-DOAS operated by University of Heidelberg will contribute with additional context information about the investigated air masses. In order to compare the remote sensing instruments with integrated profile information, in-situ instrumentation is indispensable. The in-situ package will therefore comprise wavelength-scanned Cavity-Ring-Down Spectroscopy (CRDS) for the detection of CO2, CH4, CO and H2O and a flask sampler for collection of atmospheric samples and subsequent laboratory analysis. Furthermore, the BAsic HALO Measurement And Sensor System (BAHAMAS) will provide an accurate set of meteorological and aircraft state parameters for each scientific flight. Within the frame of the first CoMet mission scheduled for the 2015 timeframe it is planned to concentrate

  8. Using VHR multispectral remote sensing and LIDAR data to determine the geomorphological effects of overbank flow on a floodplain (the Vistula River, Poland)

    NASA Astrophysics Data System (ADS)

    Wierzbicki, Grzegorz; Ostrowski, Piotr; Mazgajski, Michał; Bujakowski, Filip

    2013-02-01

    At the bottoms of river valleys, there can be found landforms developed by overbank flow such as crevasse channels and crevasse splays, usually cut off from the main river channel by the natural levées. Humans construct embankments — artificial levées which completely divide integrated parts of the river valley and thus gain new areas for agriculture and settlement purposes. However, during extremely high water stages these areas suffer from flooding, very often caused by levée breach. The objective of the study is to answer the research question: Can we use geomorphological analysis of the floodplain to predict extreme flood effects in a large river valley with an artificial levée system? The study has been conducted in a reach of the Vistula River (60 km downstream from Warsaw, Poland) that was affected by catastrophic flood event in May and June 2010. Specific emphasis has been put on using Very High Resolution (VHR) Multispectral Remote Sensing and LIDAR (LIght Detection And Ranging) data. Work is divided into three stages: (1) Identification of floodplain landforms from palaeofloods on the VHR multispectral satellite imagery; (2) Outline of the 2010 flood event (on the basis of river stage data and Acoustic Doppler Current Profiler measurements) and a detailed study of its geomorphologic effects on the floodplain (on the basis of aerial imagery and LIDAR data); (3) Comparison of landforms created in palaeofloods and in the 2010 flood event. The results of the study show that geomorphological effects of the recent catastrophic flooding are strikingly similar to palaeoflood landforms developed before the construction of an artificial levée system. The main conclusion is that overbank flow in some reaches of the floodplain causes (and will cause) similar effects as it has done in the past. Analysis of palaeoflood landforms enables prediction of these effects and can therefore prove useful for flood risk management. Post-flood transformation of palaeoflood

  9. CCD image acquisition for multispectral teledetection

    NASA Astrophysics Data System (ADS)

    Peralta-Fabi, R.; Peralta, A.; Prado, Jorge M.; Vicente, Esau; Navarette, M.

    1992-08-01

    A low cost high-reliability multispectral video system has been developed for airborne remote sensing. Three low weight CCD cameras are mounted together with a photographic camera in a keviar composite self-contained structure. The CCD cameras are remotely controlled have spectral filters (80 nm at 50 T) placed in front of their optical system and all cameras are aligned to capture the same image field. Filters may be changed so as to adjust spectral bands according to the object s reflectance properties but a set of bands common to most remote sensing aircraft and satellites are usually placed covering visible and near JR. This paper presents results obtained with this system and some comparisons as to the cost resolution and atmospheric correction advantages with respect to other more costly devices. Also a brief description of the Remotely Piloted Vehicle (RPV) project where the camera system will be mounted is given. The images so obtained replace the costlier ones obtained by satellites in severai specific applications. Other applications under development include fire monitoring identification of vegetation in the field and in the laboratory discrimination of objects by color for industrial applications and for geological and engineering surveys. 1.

  10. Remote Sensing of the Arctic Coast of Alaska Using Airborne Lidar Data

    NASA Astrophysics Data System (ADS)

    Gibbs, A.; Richmond, B. M.; Palaseanu, M.; Erikson, L. H.; Jones, B. M.; Brock, J. C.

    2013-12-01

    As part of a U.S. Geological Survey assessment of coastal change hazards, over 11,000 km2 of airborne lidar elevation data were collected along the Arctic coast of Alaska between 2009 and 2012. Data coverage includes the barrier islands and mainland coast between Icy Cape and the U.S.-Canadian border, from the shoreline to ~1.5 km inland. Data coverage extends further inland to around 3 km on the Barrow Peninsula and along the coast of the Teshekpuk Lake Special Area (TLSA) where coastal erosion rates are among the highest in the world (> 18 m/yr). Nominal point density is 1.5 m and vertical accuracy is better than 30 cm. Data were not collected over most river deltas or large embayments, with the exception of Admiralty Bay, Smith Bay (Ikpikpik Delta), Kogru River, and the Fish Creek portion of Colville River Delta. The primary use of the lidar data is to establish a modern shoreline position to be used for change analyses with historical shoreline positions. However, the lidar DEM provides a wealth of topographic and intensity data that can be used for morphological mapping of the remote arctic coast. This is one of the first comprehensive lidar datasets collected in a continuous permafrost environment. Many periglacial landscape features, such as patterned ground, ice-wedge polygons, and thermokarst lakes and former lake basins (recent and relict) are discernible in the dataset. Traditional coastal landscape features including shoreline position, beach width, slope, and bluff height and morphology are also distinct. Here we present an overview of the dataset and an assessment of methodologies developed for characterizing and classifying a variety of landscape features including overall complexity, geometry and morphology of polygonal tundra (polygon spacing, high center vs. low center), coastal bluff morphology (vertical or overhanging, convex vs. concave), drainage patterns and hydrologic connectivity. We also investigate the dataset to estimate offsets between

  11. Multispectral remote sensing from unmanned aircraft: development of workflows and comparison with WorldView-2 data

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Unmanned aircraft systems (UAS) have seen increasing use in remote sensing of natural resources in recent years. Relatively low operation costs, ability to rapidly revisit the same location, and very high resolution imagery offer new opportunities for remote sensing applications and comparison with ...

  12. Quantitative comparison of airborne remote-sensed and in situ Rhodamine WT dye and temperature during RIVET & IB09

    NASA Astrophysics Data System (ADS)

    Lenain, L.; Clark, D. B.; Guza, R. T.; Hally-Rosendahl, K.; Statom, N.; Feddersen, F.

    2012-12-01

    The transport and evolution of temperature, sediment, chlorophyll, fluorescent dye, and other tracers is of significant oceanographic interest, particularly in complex coastal environments such as the nearshore, river mouths, and tidal inlets. Remote sensing improves spatial coverage over in situ observations, and ground truthing remote sensed observations is critical for its use. Here, we present remotely sensed observations of Rhodamine WT dye and Sea Surface Temperature (SST) using the SIO Modular Aerial Sensing System (MASS) and compare them with in situ observations from the IB09 (0-300 m seaward of the surfzone, Imperial Beach, CA, October 2009) and RIVET (New River Inlet, NC, May 2012) field experiments. Dye concentrations are estimated from a unique multispectral camera system that measures the emission and absorption wavelengths of Rhodamine WT dye. During RIVET, dye is also characterized using a pushbroom hyperspectral imaging system (SPECIM AISAEagle VNIR 400-990 nm) while SST is estimated using a long-wave infrared camera (FLIR SC6000HS) coupled with an infrared pyrometer (Heitronics KT19.85II). Repeated flight passes over the dye plume were conducted approximately every 5 min for up to 4.5 hr in duration with a swath width ranging from 400 to 2000 m (altitude dependent), and provided a unique spatio-temporal depiction of the plume. A dye proxy is developed using the measured radiance at the emission and absorption wavelengths of the Rhodamine WT dye. During IB09 and RIVET, in situ dye and temperature were measured with two GPS-tracked jet skis, a small boat, and moored observations. The in situ observations are compared with the remotely sensed data in these two complex coastal environments. Funding was provided by the Office of Naval Research.

  13. Comparison of the Information Power of Multispectral Imaging and High-Resolution Spectroscopy in the Remote Sounding of Vegetation Cover

    NASA Astrophysics Data System (ADS)

    Kochubei, S. M.

    Imitation models were used to study the distortions in the chlorophyll content estimate calculated from reflectance spectra of pumpkin leaves depending on some optical parameters of measured sample and parameters of spectral device: proective cover, soil reflectance, the level of chlorophyll concentration in leaves, light filter characteristics (half-width, passband profile, intensity at maximum, signal-to-noide ratio). These results were compared to those obtained with spectrometers with high spectral resolution. The accuracy of chlorophyll estimates with multispectral devices is shown to be very sensitive to optical heterogeneity of objects and tolerant to the level of high frequency noises. The information obtained with spectrometers of high spectral resolution is sensitive to noise level, spectral resolution, and algorithm of data treatment. The deviations of calculated chlorophyll concentrations from those determined by the chemical method depend on proective cover, soil reflectance, and chlorophyll concentration in measured leaves.

  14. Investigation of Arctic mixed-phase clouds during VERDI and RACEPAC: Combining airborne remote sensing and in situ observations

    NASA Astrophysics Data System (ADS)

    Ehrlich, André; Wendisch, Manfred

    2015-04-01

    To improve our understanding of Arctic mixed-phase clouds in sea-ice covered areas the airborne research campaign Vertical distribution of ice in Arctic mixed-phase clouds (VERDI, April/May 2012) and the Radiation-Aerosol-Cloud Experiment in the Arctic Circle (RACEPAC, April/May 2014) were initiated by a collaboration of German and French research institutes. The aircraft operated by the Alfred Wegener Institute for Polar and Marine Research, Germany were based in Inuvik, Canada from where the research flights of in total 149 flight hours (62 h during VERDI, 87 h during RACEPAC) were able to cover a wide area above the Canadian Beaufort. The aim of both campaigns was to combine remote sensing and in-situ cloud, aerosol and trace gas measurements to investigate interactions between radiation, cloud and aerosol particles. Remote sensing instrumentation contained a backscatter lidar and spectral solar radiation measurements including a hyperspectral camera. In-situ sampling was highlighted by a suit of comprehensive cloud particle probes, aerosol particle counters and mass spectroscopy as well as trace gas detectors. While during VERDI remote sensing and in-situ measurements were performed by one aircraft (Polar 5) subsequently, for RACEPAC two identical aircraft (Polar 5 & 6, Basler BT-67) were coordinated at different altitudes to horizontally collocate both remote sensing and in-situ measurements. In this way not only the combined analysis of radiative and microphysical processes in the clouds can by studied more reliably, also remote sensing methods can be validated efficiently. Here we will illustrate the scientific strategy of both projects including instrumentation and flight patterns of the research flights. Beside flight missions dedicated to sample low level clouds by remote sensing and in situ probing, flights were also coordinated with satellite overpasses and ground based stations. Exemplary results will be highlighted.

  15. Remote Sensing of Chlorophyll Fluorescence by the Airborne Plant Fluorescence Sensor (APFS)

    NASA Astrophysics Data System (ADS)

    Yee, J. H.; Boldt, J.; Cook, W. B.; Morgan, F., II; Demajistre, R.; Cook, B. D.; Corp, L. A.

    2014-12-01

    Solar-induced chlorophyll fluorescence (ChlF) by terrestrial vegetation is linked closely to photosynthetic efficiency that can be exploited to monitor the plant health status and to assess the terrestrial carbon budget from space. The weak, broad continuum ChlF signal can be detected from the amount of fill-in of strong O2 absorption lines or Fraunhofer lines in the reflected solar spectral radiation. The Johns Hopkins University, Applied Physics Laboratory (JHU/APL) Airborne Plant Fluorescence Sensor (APFS) is designed and constructed specifically for airborne and groundbased ChlF measurements using the line fill-in ChlF measurement technique. In this paper, we will present the design of this triple etalon Fabry-Perot imaging instrument and the results of its vegetation fluorescence measurements obtained from the ground in the laboratory and from a NASA Langley King Air during our 2014 airborne campaign over vegetated targets in North Carolina and Virginia.

  16. Remote sensing and airborne geophysics in the assessment of natural aggregate resources

    USGS Publications Warehouse

    Knepper, D.H., Jr.; Langer, W.H.; Miller, S.H.

    1994-01-01

    Natural aggregate made from crushed stone and deposits of sand and gravel is a vital element of the construction industry in the United States. Although natural aggregate is a high volume/low value commodity that is relatively abundant, new sources of aggregate are becoming increasingly difficult to find and develop because of rigid industry specifications, political considerations, development and transporation costs, and environmental concerns, especially in urban growth centers where much of the aggregate is used. As the demand for natural aggregate increases in response to urban growth and the repair and expansion of the national infrastructure, new sources of natural aggregate will be required. The USGS has recognized the necessity of developing the capability to assess the potential for natural aggregate sources on Federal lands; at present, no methodology exists for systematically describing and evaluating potential sources of natural aggregate. Because remote sensing and airborne geophysics can detect surface and nearsurface phenomena, these tools may useful for detecting and mapping potential sources of natural aggregate; however, before a methodology for applying these tools can be developed, it is necessary to understand the type, distribution, physical properties, and characteristics of natural aggregate deposits, as well as the problems that will be encountered in assessing their potential value. There are two primary sources of natural aggregate: (1) exposed or near-surface igneous, metamorphic, and sedimentary bedrock that can be crushed, and (2) deposits of sand and gravel that may be used directly or crushed and sized to meet specifications. In any particular area, the availability of bedrock suitable for crushing is a function of the geologic history of the area - the processes that formed, deformed, eroded and exposed the bedrock. Deposits of sand and gravel are primarily surficial deposits formed by the erosion, transportation by water and ice

  17. Remote sensing of large scale methane emission sources with the Methane Airborne MAPper (MAMAP) instrument over the Kern River and Kern Front Oil fields and validation through airborne in-situ measurements - Initial results from COMEX

    NASA Astrophysics Data System (ADS)

    Gerilowski, K.; Krautwurst, S.; Kolyer, R.; Jonsson, H.; Krings, T.; Horstjann, M.; Leifer, I.; Schuettemeyer, D.; Fladeland, M. M.; Burrows, J. P.; Bovensmann, H.

    2014-12-01

    During three flights performed with the MAMAP (Methane Airborne MAPper) airborne remote sensing instrument in the framework of the CO2 and MEthane Experiment (COMEX) - a NASA and ESA funded campaign in support of HyspIRI and CarbonSat mission definition activities - large scale methane plumes were detected over the Kern River and Kern Front Oil fields in the period between June 3 and 13, 2014. MAMAP was installed for these flights aboard of the Center for Interdisciplinary Remotely-Piloted Aircraft Studies (CIRPAS) Twin Otter aircraft, together with a Picarro fast in-situ greenhouse gas (GHG) analyzer (operate by the Ames Research Center, ARC), a 5 hole turbulence probe as well as a atmospheric measurement package (operated by CIRPAS), measuring aerosols, temperature, dew-point and other atmospheric parameters. Data collected with the in-situ GHG analyzer will be used for validation of MAMAP remotely sensed data by acquiring vertical cross sections of the discovered plumes at a fixed downwind distance. Precise airborne wind information from the turbulence probe together with ground based wind data from the nearby airport will be used to estimate emission rates from the remote sensed and in-situ measured data. Remote sensed and in-situ data as well as initial flux estimates for the three flights will be presented.

  18. Daytime multispectral scanner aerial surveys of the Oak Ridge Reservation, 1992--1994: Overview of data processing and analysis by the Environmental Restoration Remote Sensing Program, Fiscal year 1995

    SciTech Connect

    Smyre, J.L.; Hodgson, M.E.; Moll, B.W.; King, A.L.; Cheng, Yang

    1995-11-01

    Environmental Restoration (ER) Remote Sensing and Special Surveys Program was in 1992 to apply the benefits of remote sensing technologies to Environmental Restoration Management (ERWM) programs at all of the five United States Department of Energy facilities operated and managed by Martin Marietta Energy Systems, Inc. (now Lockheed Martin Energy Systems)-the three Oak Ridge Reservation (ORR) facilities, the Paducah Gaseous Diffusion Plant (PGDP), the Portsmouth Gaseous Diffusion Plant (PORTS)-and adjacent off-site areas. The Remote Sensing Program includes the management of routine and special surveys at these sites, application of state-of-the-art remote sensing and geophysical technologies, and data transformation, integration, and analyses required to make the information valuable to ER. Remotely-sensed data collected of the ORR include natural color and color infrared (IR) aerial photography, 12-band multispectral scanner imagery, predawn thermal IR sensor imagery, magnetic and electromagnetic geophysical surveys, and gamma radiological data.

  19. Geometric correction of airborne remote sensing data: An operational procedure to geocode MIVIS data

    SciTech Connect

    Avanzi, G.; Bianchi, R.; Cavalli, R.M.

    1996-11-01

    Study to develop a software methodology to geocode MIVIS hyperspectral images collected by the CNR LARA Project. Gol of the study is to integrate the airborne Position and Attitude System with the image data to obtain geoceded images at a medium-small scale (1: 15000 - 1: 10000). 4 refs., 4 figs.

  20. Evaluating leaf chlorophyll content prediction from multispectral remote sensing data within a physically-based modelling framework

    NASA Astrophysics Data System (ADS)

    Croft, H.; Chen, J. M.; Zhang, Y.; Simic, A.; Noland, T. L.; Nesbitt, N.; Arabian, J.

    2015-04-01

    Accurate modelling of leaf chlorophyll content over a range of spatial and temporal scales is central to monitoring vegetation stress and physiological condition, and vegetation response to different ecological, climatic and anthropogenic drivers. A process-based modelling approach can account for variation in other factors affecting canopy reflectance, providing a more accurate estimate of chlorophyll content across different vegetation species, time-frames, and broader spatial extents. However, physically-based modelling studies usually use hyperspectral data, neglecting a wealth of data from broadband and multispectral sources. In this study, we assessed the potential for using canopy (4-Scale) and leaf radiative transfer (PROSPECT4/5) models to estimate leaf chlorophyll content using canopy Landsat satellite data and simulated Landsat bands from leaf level hyperspectral reflectance data. Over 600 leaf samples were used to test the performance of PROSPECT for different vegetation species, including black spruce (Picea mariana), sugar maple (Acer saccharum), trembling aspen (Populus tremuloides) and jack pine (Pinus banksiana). At the leaf level, hyperspectral and simulated Landsat bands showed very similar results to laboratory measured chlorophyll (R2 = 0.77 and R2 = 0.75, respectively). Comparisons between PROSPECT4 modelled chlorophyll from simulated Landsat and hyperspectral spectra showed a very close correspondence (R2 = 0.97, root mean square error (RMSE) = 3.01 μg/cm2), as did simulated reflectance bands from other broadband and narrowband sensors (MODIS: R2 = 0.99, RMSE = 1.80 μg/cm2; MERIS: R2 = 0.97, RMSE = 2.50 μg/cm2 and SPOT5 HRG: R2 = 0.96, RMSE = 5.38 μg/cm2). Modelled leaf chlorophyll content from Landsat 5 TM canopy reflectance data, acquired from over 40 ground validation sites, demonstrated a strong relationship with measured leaf chlorophyll content (R2 = 0.78, RMSE = 8.73 μg/cm2, p < 0.001), and a high linearity with negligible

  1. Converting Snow Depth to SWE: The Fusion of Simulated Data with Remote Sensing Retrievals and the Airborne Snow Observatory

    NASA Astrophysics Data System (ADS)

    Bormann, K.; Marks, D. G.; Painter, T. H.; Hedrick, A. R.; Deems, J. S.

    2015-12-01

    Snow cover monitoring has greatly benefited from remote sensing technology but, despite their critical importance, spatially distributed measurements of snow water equivalent (SWE) in mountain terrain remain elusive. Current methods of monitoring SWE rely on point measurements and are insufficient for distributed snow science and effective management of water resources. Many studies have shown that the spatial variability in SWE is largely controlled by the spatial variability in snow depth. JPL's Airborne Snow Observatory mission (ASO) combines LiDAR and spectrometer instruments to retrieve accurate and very high-resolution snow depth measurements at the watershed scale, along with other products such as snow albedo. To make best use of these high-resolution snow depths, spatially distributed snow density data are required to leverage SWE from the measured snow depths. Snow density is a spatially and temporally variable property that cannot yet be reliably extracted from remote sensing techniques, and is difficult to extrapolate to basin scales. However, some physically based snow models have shown skill in simulating bulk snow densities and therefore provide a pathway for snow depth to SWE conversion. Leveraging model ability where remote sensing options are non-existent, ASO employs a physically based snow model (iSnobal) to resolve distributed snow density dynamics across the basin. After an adjustment scheme guided by in-situ data, these density estimates are used to derive the elusive spatial distribution of SWE from the observed snow depth distributions from ASO. In this study, we describe how the process of fusing model data with remote sensing retrievals is undertaken in the context of ASO along with estimates of uncertainty in the final SWE volume products. This work will likely be of interest to those working in snow hydrology, water resource management and the broader remote sensing community.

  2. A multispectral scanner survey of the Tonopah Test Range, Nevada. Date of survey: August 1993

    SciTech Connect

    Brewster, S.B. Jr.; Howard, M.E.; Shines, J.E.

    1994-08-01

    The Multispectral Remote Sensing Department of the Remote Sensing Laboratory conducted an airborne multispectral scanner survey of a portion of the Tonopah Test Range, Nevada. The survey was conducted on August 21 and 22, 1993, using a Daedalus AADS1268 scanner and coincident aerial color photography. Flight altitudes were 5,000 feet (1,524 meters) above ground level for systematic coverage and 1,000 feet (304 meters) for selected areas of special interest. The multispectral scanner survey was initiated as part of an interim and limited investigation conducted to gather preliminary information regarding historical hazardous material release sites which could have environmental impacts. The overall investigation also includes an inventory of environmental restoration sites, a ground-based geophysical survey, and an aerial radiological survey. The multispectral scanner imagery and coincident aerial photography were analyzed for the detection, identification, and mapping of man-made soil disturbances. Several standard image enhancement techniques were applied to the data to assist image interpretation. A geologic ratio enhancement and a color composite consisting of AADS1268 channels 10, 7, and 9 (mid-infrared, red, and near-infrared spectral bands) proved most useful for detecting soil disturbances. A total of 358 disturbance sites were identified on the imagery and mapped using a geographic information system. Of these sites, 326 were located within the Tonopah Test Range while the remaining sites were present on the imagery but outside the site boundary. The mapped site locations are being used to support ongoing field investigations.

  3. Spatial Variations in CO2 Mixing Ratios Over a Heterogenous Landscape - Linking Airborne Measurements With Remote Sensing Derived Biophysical Parameters

    NASA Astrophysics Data System (ADS)

    Choi, Y.; Vadrevu, K. P.; Vay, S. A.; Woo, J.

    2006-12-01

    North American terrestrial ecosystems are major sources and sinks of carbon. Precise measurement of atmospheric CO2 concentrations plays an important role in the development and testing of carbon cycle models quantifying the influence of terrestrial CO2 exchange on the North American carbon budget. During the summer 2004 Intercontinental Chemical Transport Experiment North America (INTEX-NA) campaign, regional scale in-situ measurements of atmospheric CO2 were made from the NASA DC-8 affording the opportunity to explore how land surface heterogeneity relates to the airborne observations utilizing remote-sensing data products and GIS-based methods. These 1 Hz data reveal the seasonal biospheric uptake of CO2 over portions of the U.S. continent, especially east of 90°W below 2 km, compared to higher mixing ratios over water as well as within the upper troposphere where well-mixed, aged air masses were sampled. In this study, we use several remote sensing derived biophysical parameters from the LANDSAT, NOAA AVHRR, and MODIS sensors to specify spatiotemporal patterns of land use cover and vegetation characteristics for linking the airborne measurements of CO2 data with terrestrial sources of carbon. Also, CO2 flux footprint outputs from a 3-D Lagrangian atmospheric model have been integrated with satellite remote sensing data to infer CO2 variations across heterogeneous landscapes. In examining the landscape mosaic utilizing these available tools, preliminary results suggest that the lowest CO2 mixing ratios observed during INTEX-NA were over agricultural fields in Illinois dominated by corn then secondarily soybean crops. Low CO2 concentrations are attributable to sampling during the peak growing season over such C4 plants as corn having a higher photosynthetic rate via the C4-dicarboxylic acid pathway of carbon fixation compared to C3 plants such as soybeans. In addition to LANDSAT derived land cover data, results from comparisons of the airborne CO2 observations

  4. Airborne Particles: What We Have Learned About Their Role in Climate from Remote Sensing, and Prospects for Future Advances

    NASA Technical Reports Server (NTRS)

    Kahn, Ralph A.

    2013-01-01

    Desert dust, wildfire smoke, volcanic ash, biogenic and urban pollution particles, all affect the regional-scale climate of Earth in places and at times; some have global-scale impacts on the column radiation balance, cloud properties, atmospheric stability structure, and circulation patterns. Remote sensing has played a central role in identifying the sources and transports of airborne particles, mapping their three-dimensional distribution and variability, quantifying their amount, and constraining aerosol air mass type. The measurements obtained from remote sensing have strengths and limitations, and their value for characterizing Earths environment is enhanced immensely when they are combined with direct, in situ observations, and used to constrain aerosol transport and climate models. A similar approach has been taken to study the role particles play in determining the climate of Mars, though based on far fewer observations. This presentation will focus what we have learned from remote sensing about the impacts aerosol have on Earths climate; a few points about how aerosols affect the climate of Mars will also be introduced, in the context of how we might assess aerosol-climate impacts more generally on other worlds.

  5. Evaluation of Surface Energy Balance models for mapping evapotranspiration using very high resolution airborne remote sensing data

    NASA Astrophysics Data System (ADS)

    Paul, George

    Agriculture is the largest (90%) consumer of all fresh water in the world. The consumptive use of water by vegetation represented by the process evapotranspiration (ET) has a vital role in the dynamics of water, carbon and energy fluxes of the biosphere. Consequently, mapping ET is essential for making water a sustainable resource and also for monitoring ecosystem response to water stress and changing climate. Over the past three decades, numerous thermal remote sensing based ET mapping algorithms were developed and these have brought a significant theoretical and technical advancement in the spatial modeling of ET. Though these algorithms provided a robust, economical, and efficient tool for ET estimations at field and regional scales, yet the uncertainties in flux estimations were large, making evaluation a difficult task. The main objective of this study was to evaluate and improve the performance of widely used remote sensing based energy balance models, namely: the Surface Energy Balance Algorithm for Land (SEBAL), Mapping Evapotranspiration at high Resolution and with Internalized Calibration (METRIC), and Surface Energy Balance System (SEBS). Data used in this study was collected as part of a multi-disciplinary and multi-institutional field campaign BEAREX (Bushland Evapotranspiration and Agricultural Remote Sensing Experiment) that was conducted during 2007 and 2008 summer cropping seasons at the USDA-ARS Conservation and Production Research Laboratory (CPRL) in Bushland, Texas. Seventeen high resolution remote sensing images taken from multispectral sensors onboard aircraft and field measurements of the agro-meteorological variables from the campaign were used for model evaluation and improvement. Overall relative error measured in terms of mean absolute percent difference (MAPD) for instantaneous ET (mm h -1) were 22.7%, 23.2%, and 12.6% for SEBAL, METRIC, and SEBS, respectively. SEBAL and METRIC performances for irrigated fields representing higher ET

  6. Remote sensing of evapotranspiration over crops using combined airborne and ground-based observations

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Remote sensing of evapotranspiration (ET) over crops could be valuable for managing scarce water resources, especially for irrigated lands. In the past decade remote sensing techniques have advanced to allow frequent estimation of ET at spatial scales useful for many farms. These techniques include ...

  7. [Investigation and assessment of damage in earthquake in Yushu, Qinghai based on multi-spectral remote sensing].

    PubMed

    Wang, Fu-Tao; Zhou, Yi; Wang, Shi-Xin; Liu, Wen-Liang; Wei, Cheng-Jie; Han, Yu

    2011-04-01

    The devastating Yushu Earthquake occurred in Qinghai Province, northwest China, with a magnitude of 7.1 on April 14, 2010, which has caused huge destructive losses. Most buildings along the seismic zone were ruined, especially the old and the basic civil structure houses completely destroyed. The earthquake also triggered geological disasters, such as landslides, collapses, debris flows, etc. In the present study, the remote sensing technique was used to assess and analyze the situation of the earthquake damage. There are four classes of feature which can be interpreted according to the remote sensing imageries: (1) the damage degree of buildings, like civilian homes, temples; (2) the field disasters of earthquake, such as ground fissures, landslides, collapses, debris flows, and earthquake subsidence; (3) the damage degree of structures, such as dam; (4) the damage degree of the lifeline, for example, the highway. The features can be obtained according to high spatial resolution of remote sensing imageries, through image processing and interpretation methods. Post-disaster rehabilitation and reconstruction phase should fully consider the regional seismotectonic background and the carrying capacity of resources and environment. With the assessment results of earthquake disaster remote sensing, at last, preliminary suggestions were proposed for the rehabilitation and reconstruction planning of Yushu earthquake. PMID:21714257

  8. High altitude airborne remote sensing mission using the advanced microwave precipitation radiometer (AMPR)

    NASA Technical Reports Server (NTRS)

    Galliano, J.; Platt, R. H.; Spencer, Roy; Hood, Robbie

    1991-01-01

    The advanced microwave precipitation radiometer (AMPR) is an airborne multichannel imaging radiometer used to better understand how the earth's climate structure works. Airborne data results from the October 1990 Florida thunderstorm mission in Jacksonville, FL, are described. AMPR data on atmospheric precipitation in mesoscale storms were retrieved at 10.7, 19.35, 37.1, and 85.5 GHz onboard the ER-2 aircraft at an altitude of 20 km. AMPR's three higher-frequency data channels were selected to operate at the same frequencies as the spaceborne special sensor microwave/imager (SSM/I) presently in orbit. AMPR uses two antennas to receive the four frequencies: the lowest frequency channel uses a 9.7-in aperture lens antennas, while the three higher-frequency channels share a separate 5.3-in aperture lens antenna. The radiometer's temperature resolution performance is summarized.

  9. Airborne remote sensing of canopy water thickness scaled from leaf spectrometer data

    NASA Technical Reports Server (NTRS)

    Hunt, E. Raymond, Jr.

    1991-01-01

    The reflectance ratio of the middle-infrared band (MIR) to the near-infrared band (NIR) is linearly related to the log(10) equivalent water thickness (EWT) for single leaves of different morphologies, whereas the MIR/NIR radiance ratio is correlated with the leaf area index (LAI). The hypothesis that the MIR/NIR ratio measures canopy EWT was tested by reanalyzing airborne Thematic Mapper Simulator and field data obtained across a large gradient of LAI in western Oregon, U.S.A. The measured airborne MIR/NIR reflectance ratios for canopies were not significantly different from the predicted ratios using leaf data for canopy EWT, except for two desert woodland sites. The interpretation of the MIR/NIR ratio is scale-dependent, because leaf EWT is determined primarily by variations in LAI.

  10. Airborne Optical and Thermal Remote Sensing for Wildfire Detection and Monitoring.

    PubMed

    Allison, Robert S; Johnston, Joshua M; Craig, Gregory; Jennings, Sion

    2016-01-01

    For decades detection and monitoring of forest and other wildland fires has relied heavily on aircraft (and satellites). Technical advances and improved affordability of both sensors and sensor platforms promise to revolutionize the way aircraft detect, monitor and help suppress wildfires. Sensor systems like hyperspectral cameras, image intensifiers and thermal cameras that have previously been limited in use due to cost or technology considerations are now becoming widely available and affordable. Similarly, new airborne sensor platforms, particularly small, unmanned aircraft or drones, are enabling new applications for airborne fire sensing. In this review we outline the state of the art in direct, semi-automated and automated fire detection from both manned and unmanned aerial platforms. We discuss the operational constraints and opportunities provided by these sensor systems including a discussion of the objective evaluation of these systems in a realistic context. PMID:27548174

  11. Mining in subarctic Canada: airborne PM2.5 metal concentrations in two remote First Nations communities.

    PubMed

    Liberda, Eric N; Tsuji, Leonard J S; Peltier, Richard E

    2015-11-01

    Airborne particulate matter arising from upwind mining activities is a concern for First Nations communities in the western James Bay region of Ontario, Canada. Aerosol chemical components were collected in 2011 from two communities in northern Ontario. The chemical and mass concentration data of particulate matter collected during this study shows a significant difference in PM2.5 in Attawapiskat compared to Fort Albany. Elemental profiles indicate enhanced levels of some tracers thought to arise from mining activities, such as, K, Ni, and crustal materials. Both communities are remote and isolated from urban and industrial pollution sources, however, Attawapiskat First Nation has significantly enhanced levels of particulate matter, and it is likely that some of this arises from upwind mining activities. PMID:26255141

  12. Linking terrace geomorphology and canopy characteristics in the Peruvian Amazon using high resolution airborne remote sensing (Invited)

    NASA Astrophysics Data System (ADS)

    Chadwick, K.; Asner, G. P.

    2013-12-01

    The Peruvian Amazon is home to over half a million square kilometers of forest, nearly three quarters of which is supported by terrace landforms with variable histories. Characteristics of these terrace ecosystems have been contrasted with neighboring floodplain systems along riverine transportation corridors, but the ecological complexity within these terrace landscapes has remained largely unexplored. Airborne remote measurements provide an opportunity to consider the relationship between forest canopy characteristics and geomorphic gradients at high resolution over large spatial extents. In 2011 the Carnegie Airborne Observatory (CAO) was used to map a large section of intact lowland humid tropical forest in the southwestern Peruvian Amazon, including over nine thousand hectares of terrace forest. The CAO collected high-fidelity imaging spectroscopy data with its Visible-Shortwave Imaging Spectrometer (VSWIR) and digital elevation and canopy structure data with its high-resolution dual waveform LiDAR. These data, supplemented with field data collection, were used to quantify relationships between forest canopy traits and geomorphic gradients. Results suggest that both spectral properties of the canopy with known relationships to canopy chemistry, including pigment and nutrient concentrations, and canopy structural traits, including vegetation height and leaf area, are associated with geomorphic characteristics of this terrace landscape.

  13. Case studies of aerosol remote sensing with the Airborne Multiangle SpectroPolarimetric Imager (AirMSPI)

    NASA Astrophysics Data System (ADS)

    Diner, D. J.; Xu, F.; Garay, M. J.; Martonchik, J. V.; Kalashnikova, O. V.; Davis, A. B.; Rheingans, B.; Geier, S.; Jovanovic, V.; Bull, M.

    2012-12-01

    The Airborne Multiangle SpectroPolarimetric Imager (AirMSPI) is an 8-band (355, 380, 445, 470, 555, 660, 865, 935 nm) pushbroom camera, measuring polarization in the 470, 660, and 865 nm bands, mounted on a gimbal to acquire multiangular observations over a ±67° along-track range with 10-m spatial resolution across an 11-km wide swath. Among the instrument objectives are exploration of methodologies for combining multiangle, multispectral, polarimetric, and imaging observations to retrieve the optical depth and microphysical properties of tropospheric aerosols. AirMSPI was integrated on NASA's ER-2 high-altitude aircraft in 2010 and has successfully completed a number of flights over land and ocean targets in the Southern California vicinity. In this paper, we present case studies of AirMSPI imagery, interpreted using vector radiative transfer theory. AirMSPI observations over California's Central Valley are compared with model calculations using aerosol properties reported by the Fresno AERONET sunphotometer. Because determination of the radiative impact of different types of aerosols requires accurate attribution of the source of the reflected light along with characterization of the aerosol optical and microphysical properties, we explore the sensitivity of the Fresno measurements to variations in different aerosol properties, demonstrating the value of combining intensity and polarimetry at multiple view angles and spectral bands for constraining particle microphysical properties. Images over ocean to be presented include scenes over nearly cloud-free skies and scenes containing scattered clouds. It is well known that imperfect cloud screening confounds the determination of aerosol impact on radiation; it is perhaps less well appreciated that the effect of cloud reflections in the water can also be problematic. We calculate the magnitude of this effect in intensity and polarization and discuss its potential impact on aerosol retrievals, underscoring the value

  14. Remote sensing of phytoplankton density and diversity in Narragansett Bay using an airborne fluorosensor

    NASA Technical Reports Server (NTRS)

    Farmer, F. H.; Brown, C. A., Jr.; Jarrett, O., Jr.; Campbell, J. W.; Staton, W. L.

    1979-01-01

    An aircraft-borne remote system is presented that utilizes narrow-band light from multiple dye lasers to excite selected algae photopigments and then measures the resultant flourescence emitted from chlorophyll a at 685 nm. Tests were conducted with both pure and mixed cultures of marine algae from a series of field tests taken from piers and bridges of Narragansett Bay, and a prototype remote fluorosensor was flown over the Bay during the 1978 winter-spring diatom bloom. Remote fluorescence obtained at hover points over sea-truth stations showed correlations with in situ fluorescence, total chlorophyll a, and cell count. It was concluded that the ratio of remote fluorescence to direct chlorophyll a concentration was less variable than expected, and the distribution of total chlorophyll a between two major photoplankton color groups showed three distinct areas, within the Bay, of green and golden-brown species.

  15. An Integrated Data Acquisition / User Request/ Processing / Delivery System for Airborne Remote Sensing Data

    NASA Astrophysics Data System (ADS)

    Chapman, B.; Chu, A.; Tung, W.

    2003-12-01

    Airborne science data has historically played an important role in the development of the scientific underpinnings for spaceborne missions. When the science community determines the need for new types of spaceborne measurements, airborne campaigns are often crucial in risk mitigation for these future missions. However, full exploitation of the acquired data may be difficult due to its experimental and transitory nature. Externally to the project, most problematic (in particular, for those not involved in requesting the data acquisitions) may be the difficulty in searching for, requesting, and receiving the data, or even knowing the data exist. This can result in a rather small, insular community of users for these data sets. Internally, the difficulty for the project is in maintaining a robust processing and archival system during periods of changing mission priorities and evolving technologies. The NASA/JPL Airborne Synthetic Aperture Radar (AIRSAR) has acquired data for a large and varied community of scientists and engineers for 15 years. AIRSAR is presently supporting current NASA Earth Science Enterprise experiments, such as the Soil Moisture EXperiment (SMEX) and the Cold Land Processes experiment (CLPX), as well as experiments conducted as many as 10 years ago. During that time, it's processing, data ordering, and data delivery system has undergone evolutionary change as the cost and capability of resources has improved. AIRSAR now has a fully integrated data acquisition/user request/processing/delivery system through which most components of the data fulfillment process communicate via shared information within a database. The integration of these functions has reduced errors and increased throughput of processed data to customers.

  16. Airborne methane remote measurements reveal heavy-tail flux distribution in Four Corners region.

    PubMed

    Frankenberg, Christian; Thorpe, Andrew K; Thompson, David R; Hulley, Glynn; Kort, Eric Adam; Vance, Nick; Borchardt, Jakob; Krings, Thomas; Gerilowski, Konstantin; Sweeney, Colm; Conley, Stephen; Bue, Brian D; Aubrey, Andrew D; Hook, Simon; Green, Robert O

    2016-08-30

    Methane (CH4) impacts climate as the second strongest anthropogenic greenhouse gas and air quality by influencing tropospheric ozone levels. Space-based observations have identified the Four Corners region in the Southwest United States as an area of large CH4 enhancements. We conducted an airborne campaign in Four Corners during April 2015 with the next-generation Airborne Visible/Infrared Imaging Spectrometer (near-infrared) and Hyperspectral Thermal Emission Spectrometer (thermal infrared) imaging spectrometers to better understand the source of methane by measuring methane plumes at 1- to 3-m spatial resolution. Our analysis detected more than 250 individual methane plumes from fossil fuel harvesting, processing, and distributing infrastructures, spanning an emission range from the detection limit [Formula: see text] 2 kg/h to 5 kg/h through [Formula: see text] 5,000 kg/h. Observed sources include gas processing facilities, storage tanks, pipeline leaks, and well pads, as well as a coal mine venting shaft. Overall, plume enhancements and inferred fluxes follow a lognormal distribution, with the top 10% emitters contributing 49 to 66% to the inferred total point source flux of 0.23 Tg/y to 0.39 Tg/y. With the observed confirmation of a lognormal emission distribution, this airborne observing strategy and its ability to locate previously unknown point sources in real time provides an efficient and effective method to identify and mitigate major emissions contributors over a wide geographic area. With improved instrumentation, this capability scales to spaceborne applications [Thompson DR, et al. (2016) Geophys Res Lett 43(12):6571-6578]. Further illustration of this potential is demonstrated with two detected, confirmed, and repaired pipeline leaks during the campaign. PMID:27528660

  17. Design of an Airborne Portable Remote Imaging Spectrometer (PRISM) for the Coastal Ocean

    NASA Technical Reports Server (NTRS)

    Mouroulis, P.; vanGorp, B.; Green, R. O.; Cohen, D.; Wilson, D.; Randall, D.; Rodriguez, J.; Polanco, O.; Dierssen, H.; Balasubramanian, K.; Vargas, R.; Hein, R.; Sobel, H.; Eastwood, M.

    2010-01-01

    PRISM is a pushbroom imaging spectrometer currently under development at the Jet Propulsion Laboratory, intended to address the needs of airborne coastal ocean science research. We describe here the instrument design and the technologies that enable it to achieve its distinguishing characteristics. PRISM covers the 350-1050 nm range with a 3.1 nm sampling and a 33(deg) field of view. The design provides for high signal to noise ratio, high uniformity of response, and low polarization sensitivity. The complete instrument also incorporates two additional wavelength bands at 1240 and 1610 nm in a spot radiometer configuration to aid with atmospheric correction.

  18. Remote detection of heated ethanol plumes by airborne passive Fourier transform infrared spectrometry.

    PubMed

    Tarumi, Toshiyasu; Small, Gary W; Combs, Roger J; Kroutil, Robert T

    2003-11-01

    Methodology is developed for the automated detection of heated plumes of ethanol vapor with airborne passive Fourier transform infrared spectrometry. Positioned in a fixed-wing aircraft in a downward-looking mode, the spectrometer is used to detect ground sources of ethanol vapor from an altitude of 2000-3000 ft. Challenges to the use of this approach for the routine detection of chemical plumes include (1) the presence of a constantly changing background radiance as the aircraft flies, (2) the cost and complexity of collecting the data needed to train the classification algorithms used in implementing the plume detection, and (3) the need for rapid interferogram scans to minimize the ground area viewed per scan. To address these challenges, this work couples a novel ground-based data collection and training protocol with the use of signal processing and pattern recognition methods based on short sections of the interferogram data collected by the spectrometer. In the data collection, heated plumes of ethanol vapor are released from a portable emission stack and viewed by the spectrometer from ground level against a synthetic background designed to simulate a terrestrial radiance source. Classifiers trained with these data are subsequently tested with airborne data collected over a period of 2.5 years. Two classifier architectures are compared in this work: support vector machines (SVM) and piecewise linear discriminant analysis (PLDA). When applied to the airborne test data, the SVM classifiers perform best, failing to detect ethanol in only 8% of the cases in which it is present. False detections occur at a rate of less than 0.5%. The classifier performs well in spite of differences between the backgrounds associated with the ground-based and airborne data collections and the instrumental drift arising from the long time span of the data collection. Further improvements in classification performance are judged to require increased sophistication in the ground

  19. Remotely Measured Terrestrial Chlorophyll Fluorescence Using Airborne G-LiHT and APFS Sensors

    NASA Astrophysics Data System (ADS)

    Cook, W. B.; Yee, J. H.; Corp, L. A.; Cook, B. D.; Huemmrich, K. F.

    2014-12-01

    In September 2014 the Goddard Lidar, Hyperspectral and Thermal (G-LiHT) and the APL/JHU Airborne Plant Fluorescence Sensor (APFS) were flown together on a NASA Langley King Air over vegetated targets in North Carolina and Virginia. The instruments provided high spatial and spectral resolution data in the visible and near infrared, down-welling irradiance, elevation maps, and thermal imagery. Ground validation data was also collected concurrently. Here we report the results of these measurements and show the feasibility of using these types of instruments for collection the fluorescence and other information essential for ecological and carbon cycle studies.

  20. Using Airborne Remote Sensing to Increase Situational Awareness in Civil Protection and Humanitarian Relief - the Importance of User Involvement

    NASA Astrophysics Data System (ADS)

    Römer, H.; Kiefl, R.; Henkel, F.; Wenxi, C.; Nippold, R.; Kurz, F.; Kippnich, U.

    2016-06-01

    Enhancing situational awareness in real-time (RT) civil protection and emergency response scenarios requires the development of comprehensive monitoring concepts combining classical remote sensing disciplines with geospatial information science. In the VABENE++ project of the German Aerospace Center (DLR) monitoring tools are being developed by which innovative data acquisition approaches are combined with information extraction as well as the generation and dissemination of information products to a specific user. DLR's 3K and 4k camera system which allow for a RT acquisition and pre-processing of high resolution aerial imagery are applied in two application examples conducted with end users: a civil protection exercise with humanitarian relief organisations and a large open-air music festival in cooperation with a festival organising company. This study discusses how airborne remote sensing can significantly contribute to both, situational assessment and awareness, focussing on the downstream processes required for extracting information from imagery and for visualising and disseminating imagery in combination with other geospatial information. Valuable user feedback and impetus for further developments has been obtained from both applications, referring to innovations in thematic image analysis (supporting festival site management) and product dissemination (editable web services). Thus, this study emphasises the important role of user involvement in application-related research, i.e. by aligning it closer to user's requirements.

  1. Sub-pixel flood inundation mapping from multispectral remotely sensed images based on discrete particle swarm optimization

    NASA Astrophysics Data System (ADS)

    Li, Linyi; Chen, Yun; Yu, Xin; Liu, Rui; Huang, Chang

    2015-03-01

    The study of flood inundation is significant to human life and social economy. Remote sensing technology has provided an effective way to study the spatial and temporal characteristics of inundation. Remotely sensed images with high temporal resolutions are widely used in mapping inundation. However, mixed pixels do exist due to their relatively low spatial resolutions. One of the most popular approaches to resolve this issue is sub-pixel mapping. In this paper, a novel discrete particle swarm optimization (DPSO) based sub-pixel flood inundation mapping (DPSO-SFIM) method is proposed to achieve an improved accuracy in mapping inundation at a sub-pixel scale. The evaluation criterion for sub-pixel inundation mapping is formulated. The DPSO-SFIM algorithm is developed, including particle discrete encoding, fitness function designing and swarm search strategy. The accuracy of DPSO-SFIM in mapping inundation at a sub-pixel scale was evaluated using Landsat ETM + images from study areas in Australia and China. The results show that DPSO-SFIM consistently outperformed the four traditional SFIM methods in these study areas. A sensitivity analysis of DPSO-SFIM was also carried out to evaluate its performances. It is hoped that the results of this study will enhance the application of medium-low spatial resolution images in inundation detection and mapping, and thereby support the ecological and environmental studies of river basins.

  2. Evaluation of the airborne imaging spectrometer for remote sensing of forest stand conditions

    NASA Technical Reports Server (NTRS)

    Olson, Charles E., Jr.

    1986-01-01

    Five pairs of plots were established in forest stands with one of each pair trenched and covered to prevent precipitation from reaching the tree roots. High winds and falling limbs destroyed the covers on three of the plots. The two remaining plots were in a red pine plantation and in a natural stand of sugar maple. Trees in both plots developed levels of moisture stress more than nine bars higher than control trees on the dates of overflights with the Airborne Imaging Spectrometer (AIS) and the Collins' Airborne Spectroradiometer (CAS). Hemispherical reflectance from stressed and control trees was measured with a Beckman DK2A spectrophotometer. On the day of the AIS overflight, stressed maple foliage was less reflective than the control from 1000 to 1300 nm, but more reflective at wavelengths longer than 1300 nm. Pine foliage was less reflective than the control from 1000 to 1600 nm, but the difference was small at wavelengths longer than 1350 nm. AIS data collected showed brightness values for both maple and pine to be lower than for the controls from 1000 to 1300 nm. CAS data were used to determine the gain in species identification accuracy obtainable with high spectral resolution data.

  3. Airborne remote sensing of surface waves in the marginal ice zone

    NASA Astrophysics Data System (ADS)

    Sutherland, Peter; Gascard, Jean-Claude

    2016-04-01

    The propagation of ocean surface waves into sea ice is an important physical process in an increasingly ice-free Arctic basin. Wave-fetch-ice feedbacks are a key unknown in climate-scale simulations of Arctic sea ice, and wave effects are one of the greatest sources of uncertainty in operational ice models. We will present a technique developed for measuring waves in sea ice using airborne scanning lidar. Applying this technique to data taken during the CryoSat Validation Experiment, 2006, we were able to observe the spatial directional spectra of surface waves propagating tens of kilometres into the marginal ice zone. Wave energy attenuation and the evolution of spectral spreading were observed. Co-located visible imagery was then used to relate floe size distributions to the wave spectra. The broader-scale implications of our results, which are particularly relevant to discerning between scattering-based and dissipative wave attenuation models, will be discussed. Suggestions for minor modifications to future airborne campaigns, that would allow significantly improved capture of wave processes, will also be presented.

  4. Crop residue modeling and mapping using Landsat, ALI, hyperion and airborne remote sensing data

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Various studies have demonstrated that spectral indices derived from Landsat TM data can be used effectively to quantify crop residue cover if adequately calibrated using in situ data. However, recent developments in remote sensing technologies may possibly accelerate research related to residue cov...

  5. DETECTION AND IDENTIFICATION OF TOXIC AIR POLLUTANTS USING FIELD PORTABLE AND AIRBORNE REMOTE IMAGING SYSTEMS

    EPA Science Inventory

    Remote sensing technologies are a class of instrument and sensor systems that include laser imageries, imaging spectrometers, and visible to thermal infrared cameras. These systems have been successfully used for gas phase chemical compound identification in a variety of field e...

  6. Plume Tracker: A New Toolkit for the Mapping of Volcanic Plumes with Multispectral Thermal Infrared Remote Sensing

    NASA Astrophysics Data System (ADS)

    Realmuto, V. J.; Baxter, S.; Webley, P. W.

    2011-12-01

    Plume Tracker is the next generation of interactive plume mapping tools pioneered by MAP_SO2. First developed in 1995, MAP_SO2 has been used to study plumes at a number of volcanoes worldwide with data acquired by both airborne and space-borne instruments. The foundation of these tools is a radiative transfer (RT) model, based on MODTRAN, which we use as the forward model for our estimation of ground temperature and sulfur dioxide concentration. Plume Tracker retains the main functions of MAP_SO2, providing interactive tools to input radiance measurements and ancillary data, such as profiles of atmospheric temperature and humidity, to the retrieval procedure, generating the retrievals, and visualizing the resulting retrievals. Plume Tracker improves upon MAP_SO2 in the following areas: (1) an RT model based on an updated version of MODTRAN, (2) a retrieval procedure based on maximizing the vector projection of model spectra onto observed spectra, rather than minimizing the least-squares misfit between the model and observed spectra, (3) an ability to input ozone profiles to the RT model, (4) increased control over the vertical distribution of the atmospheric gas species used in the model, (5) a standard programmatic interface to the RT model code, based on the Component Object Model (COM) interface, which will provide access to any programming language that conforms to the COM standard, and (6) a new binning algorithm that decreases running time by exploiting spatial redundancy in the radiance data. Based on our initial testing, the binning algorithm can reduce running time by an order of magnitude. The Plume Tracker project is a collaborative effort between the Jet Propulsion Laboratory and Geophysical Institute (GI) of the University of Alaska-Fairbanks. Plume Tracker is integrated into the GI's operational plume dispersion modeling system and will ingest temperature and humidity profiles generated by the Weather Research and Forecasting model, together with

  7. Multi-trophic invasion resistance in Hawaii: bioacoustics, field surveys, and airborne remote sensing.

    PubMed

    Boelman, Natalie T; Asner, Gregory P; Hart, Patrick J; Martin, Roberta E

    2007-12-01

    We used airborne imaging spectroscopy and scanning light detection and ranging (LiDAR), along with bioacoustic recordings, to determine how a plant species invasion affects avian abundance and community composition across a range of Hawaiian submontane ecosystems. Total avian abundance and the ratio of native to exotic avifauna were highest in habitats with the highest canopy cover and height. Comparing biophysically equivalent sites, stands dominated by native Metrosideros polymorpha trees hosted larger native avian communities than did mixed stands of Metrosideros and the invasive tree Morella faya. A multi-trophic analysis strongly suggests that native avifauna provide biotic resistance against the invasion of Morella trees and exotic birds, thus slowing invasion "meltdowns" that disrupt the functioning of native Hawaiian ecosystems. PMID:18213957

  8. The relationship among sea surface roughness variations, oceanographic analyses, and airborne remote sensing analyses

    NASA Technical Reports Server (NTRS)

    Oertel, G. F.; Wade, T. L.

    1981-01-01

    The synthetic aperture radar (SAR) was studied to determine whether it could image large scale estuaries and oceanic features such as fronts and to explain the electromagnetic interaction between SAR and the individual surface front features. Fronts were observed to occur at the entrance to the Chesapeake Bay. The airborne measurements consisted of data collection by SAR onboard an F-4 aircraft and real aperture side looking radar (SLAR) in Mohawk aircraft. A total of 89 transects were flown. Surface roughness and color as well as temperature and salinity were evaluated. Cross-frontal surveys were made. Frontal shear and convergence flow were obtained. Surface active organic materials, it was indicated, are present at the air-sea interface. In all, 2000 analyses were conducted to characterize the spatial and temporal variabilities associated with water mass boundaries.

  9. Estimating sediment and caesium-137 fluxes in the Ribble Estuary through time-series airborne remote sensing.

    PubMed

    Wakefield, R; Tyler, A N; McDonald, P; Atkin, P A; Gleizon, P; Gilvear, D

    2011-03-01

    High spatial and temporal resolution airborne imagery were acquired for the Ribble Estuary, North West England in 1997 and 2003, to assess the application of time-series airborne remote sensing to quantify total suspended sediment and radionuclide fluxes during a flood and ebb tide sequence. Concomitant measurements of suspended particulate matter (SPM) and water column turbidity were obtained during the time-series image acquisition for the flood and ebb tide sequence on the 17th July 2003 to verify the assumption of a vertically well mixed estuary and thus justifying the vertical extrapolation of spatially integrated estimate of surface SPM. The ¹³⁷Cs activity concentrations were calculated from a relatively stable relationship between SPM and ¹³⁷Cs for the Ribble Estuary. Total estuary wide budgets of sediment and ¹³⁷Cs were obtained by combining the image-derived estimates of surface SPM and ¹³⁷Cs with estimates of water volume from a two-dimensional hydrodynamic model (VERSE) developed for the Ribble Estuary. These indicate that around 10,000 tons of sediment and 2.72 GBq of ¹³⁷Cs were deposited over the tidal sequence monitored in July 2003. This compared favourably with bed height elevation change estimated from field work. An uncertainty analysis on the total sediment and ¹³⁷Cs flux yielded a total budget of the order of 40% on the final estimate. The results represent a novel approach to providing a spatially integrated estimate of the total net sediment and radionuclide flux in an intertidal environment over a flood and ebb tide sequence. PMID:21195513

  10. The Australian National Airborne Field Experiment 2005: Soil Moisture Remote Sensing at 60 Meter Resolution and Up

    NASA Technical Reports Server (NTRS)

    Kim, E. J.; Walker, J. P.; Panciera, R.; Kalma, J. D.

    2006-01-01

    Spatially-distributed soil moisture observations have applications spanning a wide range of spatial resolutions from the very local needs of individual farmers to the progressively larger areas of interest to weather forecasters, water resource managers, and global climate modelers. To date, the most promising approach for space-based remote sensing of soil moisture makes use of passive microwave emission radiometers at L-band frequencies (1-2 GHz). Several soil moisture-sensing satellites have been proposed in recent years, with the European Space Agency's Soil Moisture Ocean Salinity (SMOS) mission scheduled to be launched first in a couple years. While such a microwave-based approach has the advantage of essentially allweather operation, satellite size limits spatial resolution to 10's of km. Whether used at this native resolution or in conjunction with some type of downscaling technique to generate soil moisture estimates on a finer-scale grid, the effects of subpixel spatial variability play a critical role. The soil moisture variability is typically affected by factors such as vegetation, topography, surface roughness, and soil texture. Understanding and these factors is the key to achieving accurate soil moisture retrievals at any scale. Indeed, the ability to compensate for these factors ultimately limits the achievable spatial resolution and/or accuracy of the retrieval. Over the last 20 years, a series of airborne campaigns in the USA have supported the development of algorithms for spaceborne soil moisture retrieval. The most important observations involved imagery from passive microwave radiometers. The early campaigns proved that the retrieval worked for larger and larger footprints, up to satellite-scale footprints. These provided the solid basis for proposing the satellite missions. More recent campaigns have explored other aspects such as retrieval performance through greater amounts of vegetation. All of these campaigns featured extensive ground

  11. Effects of water-emission anisotropy on multispectral remote sensing at thermal wavelengths of ocean temperature and of cirrus clouds

    NASA Technical Reports Server (NTRS)

    Otterman, J.; Susskind, J.; Dalu, G.; Kratz, D.; Goldberg, I. L.

    1992-01-01

    The impact of water-emission anisotropy on remotedly sensed long-wave data has been studied. Water emission is formulated from a calm body for a facile computation of radiative transfer in the atmosphere. The error stemming from the blackbody assumption are calculated for cases of a purely absorbing or a purely scattering atmosphere taking the optical properties of the atmosphere as known. For an absorbing atmosphere, the errors in the sea-surface temperature (SST) are found to be always reduced and be the same whether measurements are made from space or at any level of the atmosphere. The inferred optical thickness tau of an absorbing layer can be in error under the blackbody assumption by a delta tau of 0.01-0.08, while the inferred optical thickness of a scattering layer can be in error by a larger amount, delta tau of 0.03-0.13. It is concluded that the error delta tau depends only weakly on the actual optical thickness and the viewing angle, but is rather sensitive to the wavelength of the measurement.

  12. Ramgarh Crater, Rajasthan, India - Study of multispectral images obtained by Indian remote sensing satellite (IRS-IA)

    NASA Technical Reports Server (NTRS)

    Murali, A. V.; Lulla, Kamlesh P.

    1992-01-01

    Ramgarh Crater, Rajasthan, India is a potential impact crater that has not been studied so far. The proximity of Ramgarh Crater to the Deccan flood basalt terrain makes it important to examine the spatial and temporal relationship of this crater to Deccan Volcanism because recent studies propose a strong link between impact cratering and major flood basalt eruptions. A detailed multidisciplinary study is necessary to evaluate the structure and lithology of Ramgarh Crater and its temporal relationship to the emplacement of Deccan eruptions in India. Application of the IRS-IA data to study the lithologic/surface characteristics of Ramgarh Crater (attempted for the first time) indicates the potential application of remote sensing data in these studies. The IRS-IA data are of good quality and resolution. Our preliminary assessment has shown that these data are helpful in generating lithology soil vegetation profiles of Ramgarh Crater region. These 'profile maps' would be useful for targeting the specific areas in the region for a closer look and ground truth verification during the field work and sample collection in the region.

  13. Interpretation of air pollution data as measured by an airborne remote sensor

    NASA Technical Reports Server (NTRS)

    Smith, G. L.; Young, G. R.; Green, R. N.

    1974-01-01

    The investigation described is a continuation of the work reported by Smith et al. (1974) in which a single source was studied. In the current study, multiple sources of known location are considered. The study is concerned with the strength of each source and the resulting pollution concentration field. The characteristics of the remotely sensed data are discussed along with the parameter estimation procedure, the estimation of pollution parameters, and a numerical example.

  14. Airborne Geophysics and Remote Sensing Applied to Study Greenland Ice Dynamics

    NASA Technical Reports Server (NTRS)

    Csatho, Beata M.

    2003-01-01

    Overview of project: we combined and jointly analysed geophysical, remote sensing and glaciological data for investigating the temporal changes in ice flow and the role of geologic control on glacial drainage. The project included two different studies, the investigation of recent changes of the Kangerlussuaq glacier and the study of geologic control of ice flow in NW Greenland, around the Humboldt, Petermann and Ryder glaciers.

  15. Airborne Remote Observations of L-Band Radio Frequency Interference and Implications for Satellite Missions

    NASA Technical Reports Server (NTRS)

    Laymon, Charles; Srinivasan, Karthik; Limaye, Ashutosh

    2011-01-01

    Passive remote sensing of the Earth s surface and atmosphere from space has significant importance in operational and research environmental studies, in particular for the scientific understanding, monitoring and prediction of climate change and its impacts. Passive remote sensing requires the measurement of naturally occurring radiations, usually of very low power levels, which contain essential information on the physical process under investigation. As such, these sensed radio frequency bands are a unique natural resource enabling space borne passive sensing of the atmosphere and the Earth s surface that deserves adequate allocation to the Earth Exploration Satellite Service and absolute protection from interference. Unfortunately, radio frequency interference (RFI) is an increasing problem for Earth remote sensing, particularly for passive observations of natural emissions. Because these natural signals tend to be very weak, even low levels of interference received by a passive sensor may degrade the fidelity of scientific data. The characteristics of RFI (low-level interference and radar-pulse noise) are not well known because there has been no systematic surveillance, spectrum inventory or mapping of RFI. While conducting a flight experiment over central Tennessee in May 2010, RFI, a concern for any instrument operating in the passive L band frequency, was observed across 16 subbands between 1402-1427 MHz. Such a survey provides rare characterization data from which to further develop mitigation technologies as well as to identify bandwidths to avoid in future sensor formulation.

  16. MULTISPECTRAL THERMAL IMAGER - OVERVIEW

    SciTech Connect

    P. WEBER

    2001-03-01

    The Multispectral Thermal Imager satellite fills a new and important role in advancing the state of the art in remote sensing sciences. Initial results with the full calibration system operating indicate that the system was already close to achieving the very ambitious goals which we laid out in 1993, and we are confident of reaching all of these goals as we continue our research and improve our analyses. In addition to the DOE interests, the satellite is tasked about one-third of the time with requests from other users supporting research ranging from volcanology to atmospheric sciences.

  17. Multispectral thermal imaging

    SciTech Connect

    Weber, P.G.; Bender, S.C.; Borel, C.C.; Clodius, W.B.; Smith, B.W.; Garrett, A.; Pendergast, M.M.; Kay, R.R.

    1998-12-01

    Many remote sensing applications rely on imaging spectrometry. Here the authors use imaging spectrometry for thermal and multispectral signatures measured from a satellite platform enhanced with a combination of accurate calibrations and on-board data for correcting atmospheric distortions. The approach is supported by physics-based end-to-end modeling and analysis, which permits a cost-effective balance between various hardware and software aspects. The goal is to develop and demonstrate advanced technologies and analysis tools toward meeting the needs of the customer; at the same time, the attributes of this system can address other applications in such areas as environmental change, agriculture, and volcanology.

  18. Solid state frequency conversion technology for remote sensing

    SciTech Connect

    Velsko, S.P.; Webb, M.S.; Cook, W.M.; Neuman, W.A.

    1994-07-01

    Long range remote sensing from airborne or other highly mobile platforms will require high average power tunable radiation from very compact and efficient laser systems. The solid state laser pumped optical parametric oscillator (OPO) has emerged as a leading candidate for such high average power, widely tunable sources. In contrast to laboratory systems, efficiency and simplicity can be the decisive issues which determine the practicality of a particular airborne remote sensing application. The recent advent of diode laser pumped solid state lasers has produced high average power OPO pump sources which are themselves both compact and efficient. However, parametric oscillator technology which can efficiently convert the average powers provided by these pump sources remains to be demonstrated. In addition to the average power requirement, many airborne long range sensing tasks will require a high degree of frequency multiplexing to disentangle data from multiple chemical species. A key advantage in system simplicity can be obtained, for example, if a single OPO can produce easily controlled multispectral output. In this paper the authors address several topics pertaining to the conversion efficiency, power handling, and multispectral capabilities of OPOs which they are currently investigating. In Section 2, single pulse conversion efficiency issues are addressed, while average power effects are treated in Section 3. Section 4 is concerned with multispectral performance of a single OPO. The last section contains a short summary and some concluding remarks.

  19. The NASA/NSERC Student Airborne Research Program Land Focus Group - a Paid Training Program in Multi-Disciplinary STEM Research for Terrestrial Remote Sensing

    NASA Astrophysics Data System (ADS)

    Kefauver, S. C.; Ustin, S.; Davey, S. W.; Furey, B. J.; Gartner, A.; Kurzweil, D.; Siebach, K. L.; Slawsky, L.; Snyder, E.; Trammell, J.; Young, J.; Schaller, E.; Shetter, R. E.

    2011-12-01

    The Student Airborne Research Program (SARP) of the National Aeronautics and Space Administration (NASA) and the National Suborbital Education and Research Center (NSERC) is a unique six week multidisciplinary paid training program which directly integrates students into the forefront of airborne remote sensing science. Students were briefly trained with one week of lectures and laboratory exercises and then immediately incorporated into ongoing research projects which benefit from access to the DC-8 airborne platform and the MODIS-ASTER Airborne Simulator (MASTER) sensor. Students were split into three major topical categories of Land, Ocean, and Air for the data collection and project portions of the program. This poster details the techniques and structure used for the student integration into ongoing research, professional development, hypothesis building and results as developed by the professor and mentor of the Land focus group. Upon assignment to the Land group, students were issued official research field protocols and split into four field specialty groups with additional specialty reading assignments. In the field each group spent more time in their respective specialty, but also participated in all field techniques through pairings with UC Davis research team members using midday rotations. After the field campaign, each specialty group then gave summary presentations on the techniques, preliminary results, and significance to overall group objectives of their specialty. Then students were required to submit project proposals within the bounds of Land airborne remote sensing science and encouraging, but not requiring the use of the field campaign data. These proposals are then reviewed by the professor and mentor and students are met with one by one to discuss the skills of each student and objectives of the proposed research project. The students then work under the supervision of the mentor and benefit again from professor feedback in a formal

  20. A multispectral scanner survey of the United States Department of Energy's Paducah Gaseous Diffusion Plant

    SciTech Connect

    Not Available

    1991-06-01

    Airborne multispectral scanner data of the Paducah Gaseous Diffusion Plant (PGDP) and surrounding area were acquired during late spring 1990. This survey was conducted by the Remote Sensing Laboratory (RSL) which is operated by EG G Energy Measurements (EG G/EM) for the US Department of Energy (DOE) Nevada Operations Office. It was requested by the US Department of Energy (DOE) Environmental Audit Team which was reviewing environmental conditions at the facility. The objectives of this survey were to: (1) Acquire 12-channel, multispectral scanner data of the PGDP from an altitude of 3000 feet above ground level (AGL); (2) Acquire predawn, digital thermal infrared (TIR) data of the site from the same altitude; (3) Collect color and color-infrared (CIR) aerial photographs over the facilities; and (4) Illustrate how the analyses of these data could benefit environmental monitoring at the PGDP. This report summarizes the two multispectral scanner and aerial photographic missions at the Paducah Gaseous Diffusion Plant. Selected examples of the multispectral data are presented to illustrate its potential for aiding environmental management at the site. 4 refs., 1 fig., 2 tabs.

  1. Optimizing the number of training areas for modeling above-ground biomass with ALS and multispectral remote sensing in subtropical Nepal

    NASA Astrophysics Data System (ADS)

    Rana, Parvez; Gautam, Basanta; Tokola, Timo

    2016-07-01

    Remote sensing-based inventories of above-ground forest biomass (AGB) require a set of training plots representative of the area to be studied, the collection of which is the most expensive part of the analysis. These are time-consuming and costly because the large variety in forest conditions requires more plots to adequately capture this variability. A field campaign in general is challenging and is hampered by the complex topographic conditions, limited accessibility, steep mountainous terrains which increase labor efforts and costs. In addition it is also depend on the ratio between size of study area and number of training plots. In this study, we evaluate the number of training areas (sample size) required to estimate AGB for an area in the southern part of Nepal using airborne laser scanning (ALS), RapidEye and Landsat data. Three experiments were conducted: (i) AGB model performance, based on all the field training plots; (ii) reduction of the sample size, based on the ALS metrics and the AGB distribution; and (iii) prediction of the optimal number of training plots, based on the correlation between the remote sensing and field data. The AGB model was fitted using the sparse Bayesian method. AGB model performance was validated using an independent validation dataset. The effect of the strategies for reducing the sample size was readily apparent for the ALS-based AGB prediction, but the RapidEye and Landsat sensor data failed to capture any such effect. The results indicate that adequate coverage of the variability in tree height and density was an important condition for selecting the training plots. In addition, the ALS-based AGB prediction required the smallest number of training plots and was also quite stable with a small number of field plots.

  2. Polarimetric Multispectral Imaging Technology

    NASA Technical Reports Server (NTRS)

    Cheng, L.-J.; Chao, T.-H.; Dowdy, M.; Mahoney, C.; Reyes, G.

    1993-01-01

    The Jet Propulsion Laboratory is developing a remote sensing technology on which a new generation of compact, lightweight, high-resolution, low-power, reliable, versatile, programmable scientific polarimetric multispectral imaging instruments can be built to meet the challenge of future planetary exploration missions. The instrument is based on the fast programmable acousto-optic tunable filter (AOTF) of tellurium dioxide (TeO2) that operates in the wavelength range of 0.4-5 microns. Basically, the AOTF multispectral imaging instrument measures incoming light intensity as a function of spatial coordinates, wavelength, and polarization. Its operation can be in either sequential, random access, or multiwavelength mode as required. This provides observation flexibility, allowing real-time alternation among desired observations, collecting needed data only, minimizing data transmission, and permitting implementation of new experiments. These will result in optimization of the mission performance with minimal resources. Recently we completed a polarimetric multispectral imaging prototype instrument and performed outdoor field experiments for evaluating application potentials of the technology. We also investigated potential improvements on AOTF performance to strengthen technology readiness for applications. This paper will give a status report on the technology and a prospect toward future planetary exploration.

  3. Identification and Atmospheric Transport of Microcystin Around Southern California Using Airborne Remote Sensing

    NASA Astrophysics Data System (ADS)

    Conlin, J.; Kudela, R. M.; Broughton, J.

    2014-12-01

    Microcystin, a hepatotoxin produced by the cyanobacteria Microcystis, has been known to contaminate fresh water sources around southern California. Ingesting this toxin can cause death in animals and illnesses in humans, which has promoted the World Health Organization (WHO) and California to establish preliminary guidelines for microcystin concentrations in the water (1 μg/L in drinking water and 0.8 μg/L for recreational exposure respectively). However, very few studies have been done to assess the effects of this toxin when aerosolized, even though Fitzgeorge et al. (1994) describes the toxin as potentially 12x more deadly if inhaled rather than swallowed. This project aimed to identify areas with the potential for high microcystin concentrations using airborne data and then model the potential atmospheric transport of the toxin. After applying the Master Scattering Line Height (MSLH) and Aphanizomenon-Microcystis Index (AMI) algorithms to Airborne Visible/ Infrared Imaging Spectrometer (AVIRIS), multiple water bodies were identified as having the potential for Microcystis, although many of the observed water bodies had AMI values indicating the presence of Aphanizomenon-- a non-toxic cyanobacteria that is usually present before Microcystis. A relationship between toxins and biomass was developed and used to estimate the amount of phycocyanin and dissolved microcystin in the water. Brevetoxin, common in the Florida 'red tides', was used as a proxy to estimate the amount of microcystin that becomes aerosolized given a known water concentration (Kirkpatrick et al, 2010). These amounts were then run and averaged with the HYSPLIT dispersion model for 4 hours, 12 hours, and 24 hours. The final results show that most areas are exposed to less than 0.1 ng/m^3 after 4 hours. As a worst case scenario, one final model was run to show the exposure amount when Pinto Lake was observed to have the maximum amount of microcystin recorded in 2007. The results show that after 4

  4. Applying Neural Networks to Hyperspectral and Multispectral Field Data for Discrimination of Cruciferous Weeds in Winter Crops

    PubMed Central

    de Castro, Ana-Isabel; Jurado-Expósito, Montserrat; Gómez-Casero, María-Teresa; López-Granados, Francisca

    2012-01-01

    In the context of detection of weeds in crops for site-specific weed control, on-ground spectral reflectance measurements are the first step to determine the potential of remote spectral data to classify weeds and crops. Field studies were conducted for four years at different locations in Spain. We aimed to distinguish cruciferous weeds in wheat and broad bean crops, using hyperspectral and multispectral readings in the visible and near-infrared spectrum. To identify differences in reflectance between cruciferous weeds, we applied three classification methods: stepwise discriminant (STEPDISC) analysis and two neural networks, specifically, multilayer perceptron (MLP) and radial basis function (RBF). Hyperspectral and multispectral signatures of cruciferous weeds, and wheat and broad bean crops can be classified using STEPDISC analysis, and MLP and RBF neural networks with different success, being the MLP model the most accurate with 100%, or higher than 98.1%, of classification performance for all the years. Classification accuracy from hyperspectral signatures was similar to that from multispectral and spectral indices, suggesting that little advantage would be obtained by using more expensive airborne hyperspectral imagery. Therefore, for next investigations, we recommend using multispectral remote imagery to explore whether they can potentially discriminate these weeds and crops. PMID:22629171

  5. Multispectral imaging method and apparatus

    DOEpatents

    Sandison, D.R.; Platzbecker, M.R.; Vargo, T.D.; Lockhart, R.R.; Descour, M.R.; Richards-Kortum, R.

    1999-07-06

    A multispectral imaging method and apparatus are described which are adapted for use in determining material properties, especially properties characteristic of abnormal non-dermal cells. A target is illuminated with a narrow band light beam. The target expresses light in response to the excitation. The expressed light is collected and the target's response at specific response wavelengths to specific excitation wavelengths is measured. From the measured multispectral response the target's properties can be determined. A sealed, remote probe and robust components can be used for cervical imaging. 5 figs.

  6. Multispectral imaging method and apparatus

    DOEpatents

    Sandison, David R.; Platzbecker, Mark R.; Vargo, Timothy D.; Lockhart, Randal R.; Descour, Michael R.; Richards-Kortum, Rebecca

    1999-01-01

    A multispectral imaging method and apparatus adapted for use in determining material properties, especially properties characteristic of abnormal non-dermal cells. A target is illuminated with a narrow band light beam. The target expresses light in response to the excitation. The expressed light is collected and the target's response at specific response wavelengths to specific excitation wavelengths is measured. From the measured multispectral response the target's properties can be determined. A sealed, remote probe and robust components can be used for cervical imaging

  7. Application of multimode airborne digital camera system in Wenchuan earthquake disaster monitoring

    NASA Astrophysics Data System (ADS)

    Liu, Xue; Li, Qingting; Fang, Junyong; Tong, Qingxi; Zheng, Lanfen

    2009-06-01

    Remote sensing, especially airborne remote sensing, can be an invaluable technique for quick response to natural disasters. Timely acquired images by airborne remote sensing can provide very important information for the headquarters and decision makers to be aware of the disaster situation, and make effective relief arrangements. The image acquisition and processing of Multi-mode Airborne Digital Camera System (MADC) and its application in Wenchuan earthquake disaster monitoring are presented in this paper. MADC system is a novel airborne digital camera developed by Institute of Remote Sensing Applications, Chinese Academy of Sciences. This camera system can acquire high quality images in three modes, namely wide field, multi-spectral (hyper-spectral) and stereo conformation. The basic components and technical parameters of MADC are also presented in this paper. MADC system played a very important role in the disaster monitoring of Wenchuan earthquake. In particular, the map of dammed lakes in Jianjiang river area was produced and provided to the front line headquarters. Analytical methods and information extraction techniques of MADC are introduced. Some typical analytical and imaging results are given too. Suggestions for the design and configuration of the airborne sensors are discussed at the end of this paper.

  8. Mapping Weathering and Alteration Minerals in the Comstock and Geiger Grade Areas using Visible to Thermal Infrared Airborne Remote Sensing Data

    NASA Technical Reports Server (NTRS)

    Vaughan, Greg R.; Calvin, Wendy M.

    2005-01-01

    To support research into both precious metal exploration and environmental site characterization a combination of high spatial/spectral resolution airborne visible, near infrared, short wave infrared (VNIR/SWIR) and thermal infrared (TIR) image data were acquired to remotely map hydrothermal alteration minerals around the Geiger Grade and Comstock alteration regions, and map the mineral by-products of weathered mine dumps in Virginia City. Remote sensing data from the Airborne Visible Infrared Imaging Spectrometer (AVIRIS), SpecTIR Corporation's airborne hyperspectral imager (HyperSpecTIR), the MODIS-ASTER airborne simulator (MASTER), and the Spatially Enhanced Broadband Array Spectrograph System (SEBASS) were acquired and processed into mineral maps based on the unique spectral signatures of image pixels. VNIR/SWIR and TIR field spectrometer data were collected for both calibration and validation of the remote data sets, and field sampling, laboratory spectral analyses and XRD analyses were made to corroborate the surface mineralogy identified by spectroscopy. The resulting mineral maps show the spatial distribution of several important alteration minerals around each study area including alunite, quartz, pyrophyllite, kaolinite, montmorillonite/muscovite, and chlorite. In the Comstock region the mineral maps show acid-sulfate alteration, widespread propylitic alteration and extensive faulting that offsets the acid-sulfate areas, in contrast to the larger, dominantly acid-sulfate alteration exposed along Geiger Grade. Also, different mineral zones within the intense acid-sulfate areas were mapped. In the Virginia City historic mining district the important weathering minerals mapped include hematite, goethite, jarosite and hydrous sulfate minerals (hexahydrite, alunogen and gypsum) located on mine dumps. Sulfate minerals indicate acidic water forming in the mine dump environment. While there is not an immediate threat to the community, there are clearly sources of

  9. Passive remote sensing of large-scale methane emissions from Oil Fields in California's San Joaquin Valley and validation by airborne in-situ measurements - Results from COMEX

    NASA Astrophysics Data System (ADS)

    Gerilowski, Konstantin; Krautwurst, Sven; Thompson, David R.; Thorpe, Andrew K.; Kolyer, Richard W.; Jonsson, Haflidi; Krings, Thomas; Frankenberg, Christian; Horstjann, Markus; Leifer, Ira; Eastwood, Michael; Green, Robert O.; Vigil, Sam; Fladeland, Matthew; Schüttemeyer, Dirk; Burrows, John P.; Bovensmann, Heinrich

    2016-04-01

    The CO2 and MEthane EXperiment (COMEX) was a NASA and ESA funded campaign in support of the HyspIRI and CarbonSat mission definition activities. As a part of this effort, seven flights were performed between June 3 and September 4, 2014 with the Methane Airborne MAPper (MAMAP) remote sensing instrument (operated by the University of Bremen in cooperation with the German Research Centre for Geosciences - GFZ) over the Kern River, Kern Front, and Poso Creek Oil Fields located in California's San Joaquin Valley. MAMAP was installed for the flights aboard the Center for Interdisciplinary Remotely-Piloted Aircraft Studies (CIRPAS) Twin Otter aircraft, together with: a Picarro fast in-situ greenhouse gas (GHG) analyzer operated by the NASA Ames Research Center, ARC; a 5-hole turbulence probe; and an atmospheric measurement package operated by CIRPAS measuring aerosols, temperature, dew-point, and other atmospheric parameters. Three of the flights were accompanied by the Next Generation Airborne Visual InfraRed Imaging Spectrometer (AVIRIS-NG), operated by the Jet Propulsion Laboratory (JPL), California Institute of Technology, installed aboard a second Twin Otter aircraft. Large-scale, high-concentration CH4 plumes were detected by the MAMAP instrument over the fields and tracked over several kilometers. The spatial distribution of the MAMAP observed plumes was compared to high spatial resolution CH4 anomaly maps derived by AVIRIS-NG imaging spectroscopy data. Remote sensing data collected by MAMAP was used to infer CH4 emission rates and their distributions over the three fields. Aggregated emission estimates for the three fields were compared to aggregated emissions inferred by subsequent airborne in-situ validation measurements collected by the Picarro instrument. Comparison of remote sensing and in-situ flux estimates will be presented, demonstrating the ability of airborne remote sensing data to provide accurate emission estimates for concentrations above the

  10. Airborne in situ vertical profiling of HDO/H216O in the subtropical troposphere during the MUSICA remote sensing validation campaign

    NASA Astrophysics Data System (ADS)

    Dyroff, C.; Sanati, S.; Christner, E.; Zahn, A.; Balzer, M.; Bouquet, H.; McManus, J. B.; González-Ramos, Y.; Schneider, M.

    2015-01-01

    Vertical profiles of water vapor (H2O) and its isotope ratio D / H expressed as δ D(H2O were measured in situ by the ISOWAT II diode-laser spectrometer during the MUlti-platform remote Sensing of Isotopologues for investigating the Cycle of Atmospheric water (MUSICA) airborne campaign. We present recent modifications of the instrument design. The instrument calibration on the ground as well as in flight is described. Based on the calibration measurements, the humidity-dependent uncertainty of our airborne data is determined. For the majority of the airborne data we achieved an accuracy (uncertainty of the mean) of Δ(δ D) ≈ 10‰. Vertical profiles between 150 and ~7000 m were obtained during 7 days in July and August 2013 over the subtropical North Atlantic Ocean near Tenerife. The flights were coordinated with ground-based (Network for the Detection of Atmospheric Composition Change, NDACC) and space-based (Infrared Atmospheric Sounding Interferometer, IASI) FTIR remote-sensing measurements of δ D(H2O) as a means to validate the remote sensing humidity and δ D(H2O) data products. The results of the validation are presented in detail in a separate paper (Schneider et al., 2014). The profiles were obtained with a high vertical resolution of around 3 m. By analyzing humidity and δ D(H2O) correlations we were able to identify different layers of airmasses with specific isotopic signatures. The results are discussed.

  11. Airborne in situ vertical profiling of HDO / H216O in the subtropical troposphere during the MUSICA remote sensing validation campaign

    NASA Astrophysics Data System (ADS)

    Dyroff, C.; Sanati, S.; Christner, E.; Zahn, A.; Balzer, M.; Bouquet, H.; McManus, J. B.; Gonzalez-Ramos, Y.; Schneider, M.

    2015-05-01

    Vertical profiles of water vapor (H2O) and its isotope ratio D / H expressed as δD(H2O) were measured in situ by the ISOWAT II diode-laser spectrometer during the MUlti-platform remote Sensing of Isotopologues for investigating the Cycle of Atmospheric water (MUSICA) airborne campaign. We present recent modifications of the instrument design. The instrument calibration on the ground as well as in flight is described. Based on the calibration measurements, the humidity-dependent uncertainty of our airborne data is determined. For the majority of the airborne data we achieved an accuracy (uncertainty of the mean) of Δ(δD) ≈10‰. Vertical profiles between 150 and ~7000 m were obtained during 7 days in July and August 2013 over the subtropical North Atlantic Ocean near Tenerife. The flights were coordinated with ground-based (Network for the Detection of Atmospheric Composition Change, NDACC) and space-based (Infrared Atmospheric Sounding Interferometer, IASI) FTIR remote sensing measurements of δD(H2O) as a means to validate the remote sensing humidity and δD(H2O) data products. The results of the validation are presented in detail in a separate paper (Schneider et al., 2014). The profiles were obtained with a high vertical resolution of around 3 m. By analyzing humidity and δD(H2O) correlations we were able to identify different layers of air masses with specific isotopic signatures. The results are discussed.

  12. A comparison of multi-spectral, multi-angular, and multi-temporal remote sensing datasets for fractional shrub canopy mapping in Arctic Alaska

    USGS Publications Warehouse

    Selkowitz, D.J.

    2010-01-01

    Shrub cover appears to be increasing across many areas of the Arctic tundra biome, and increasing shrub cover in the Arctic has the potential to significantly impact global carbon budgets and the global climate system. For most of the Arctic, however, there is no existing baseline inventory of shrub canopy cover, as existing maps of Arctic vegetation provide little information about the density of shrub cover at a moderate spatial resolution across the region. Remotely-sensed fractional shrub canopy maps can provide this necessary baseline inventory of shrub cover. In this study, we compare the accuracy of fractional shrub canopy (> 0.5 m tall) maps derived from multi-spectral, multi-angular, and multi-temporal datasets from Landsat imagery at 30 m spatial resolution, Moderate Resolution Imaging SpectroRadiometer (MODIS) imagery at 250 m and 500 m spatial resolution, and MultiAngle Imaging Spectroradiometer (MISR) imagery at 275 m spatial resolution for a 1067 km2 study area in Arctic Alaska. The study area is centered at 69 ??N, ranges in elevation from 130 to 770 m, is composed primarily of rolling topography with gentle slopes less than 10??, and is free of glaciers and perennial snow cover. Shrubs > 0.5 m in height cover 2.9% of the study area and are primarily confined to patches associated with specific landscape features. Reference fractional shrub canopy is determined from in situ shrub canopy measurements and a high spatial resolution IKONOS image swath. Regression tree models are constructed to estimate fractional canopy cover at 250 m using different combinations of input data from Landsat, MODIS, and MISR. Results indicate that multi-spectral data provide substantially more accurate estimates of fractional shrub canopy cover than multi-angular or multi-temporal data. Higher spatial resolution datasets also provide more accurate estimates of fractional shrub canopy cover (aggregated to moderate spatial resolutions) than lower spatial resolution datasets

  13. Advanced PV/PC HgCdTe hybrid IRFPA for satellite-based high-resolution multispectral remote sensing

    NASA Astrophysics Data System (ADS)

    Rutter, James H., Jr.; Jungkman, Dave; Stobie, James A.; Krueger, Eric E.; Krueger, M.; Garnett, James D.; Reine, Marion B.; Denley, Brian; Kleinmann, Douglas E.; Gurnee, Mark N.

    1995-09-01

    AIRS is a key facility instrument on the first post meridian platform as part of NASA'a Earth Observing System (EOS) program. The Atmospheric Infrared Sounder measurement technique is based on passive IR remote sensing using a high spectral resolution grating spectrometer. The structure of the infrared focal plane for the AIRS instrument has been defined and is presented in this paper. The optical footprint of 8.1 mm by 36.3 mm along with the necessary support and interface components leads to a focal plane assembly of 53 mm by 66 mm, the largest ever built at LIRIS. With 4208 diodes and 274 photoconductors in the same focal plane to achieve the wide spectral coverage from 3.7 to 15.4 micrometers , a modular approach is required. Ten PV modules utilize silicon readout integrated circuits (ROICs) joined to the detector arrays as either direct or indirect hybrids while two PC modules cover the 13.7 to 15.4 mm range, optically chopped and led out to uncooled preamplifiers. The simultaneous operation of PV and PC devices in the same focal plane has required unique approaches to shielding, ROIC output design and lead routing. High D*'s of 7E14 and 3E11 cm- Hz1/2/W are needed to meet the sensitivity requirements of the 4.2 and 15.0 micrometers regions respectively. The 35 micrometers by 800 micrometers PC detectors on a 50 micrometers pitch have necessitated modifications to standard delineation techniques, while the MW performance is nearly D* BLIP for PV devices. Dispersed energy is presented to the modules through 17 narrow band filters packaged into a single precision assembly mounted within 0.18-0.25 mm of the focal plane surface. The more than 50 components comprising the focal plane in conjunction with the tightly spaced optical pattern presented by the grating add a high degree of complexity to the assembly process. This paper focuses on the architectural constraints derived from performance, interface, and reliability requirements. Key aspects of these

  14. Airborne remote sensing of photosynthetic light use efficiency and carbon uptake along an Arctic transect in Finland

    NASA Astrophysics Data System (ADS)

    Atherton, J.; Hill, T. C.; Prieto-Blanco, A.; Wade, T.; Clement, R.; Moncrieff, J.; Williams, M. D.; Disney, M.; Nichol, C. J.

    2009-12-01

    It is critical to understand the dynamics of ecosystem carbon uptake through seasonal changes and in response to environmental drivers. In this study we utilised aircraft based remote sensing and CO2/H2O flux monitoring systems to quantify changes in photosynthesis along an Arctic transect. The University of Edinburgh's (UK) research aircraft (a Diamond HK 36 TTC-ECO Dimona) was deployed in the Arctic during summer 2008 to carry out a series of transect-flights over a birch-mire mosaic site near Kevo, Finland as part of the Arctic Biosphere Atmosphere Coupling at Multiple Scales (ABACUS) project. The aircraft is equipped with automated dual field-of-view (hyperspectral) radiometers and CO2/H2O flux and meteorological instrumentation. Vegetation indices known to be related to photosynthetic light use efficiency (LUE), including the well established Photochemical Reflectance Index (PRI) and Solar-induced Fluorescence (SiF) as well as the Normalized Difference Vegetation Index (NDVI) were calculated from the spectral data and matched in space to the CO2 flux measurements. We explored spatial relationships between NDVI and CO2 flux, LUE (CO2 flux / Absorbed Photosynthetically Active Radiation) and PRI and finally SiF (calculated using the Fraunhofer infilling method) and relevant environmental drivers. Our results highlight the unique ability of an airborne platform to quantify ecosystem physiology across a landscape and demonstrate how such measurements can bridge the spatial gap between ground and satellite-based observations.

  15. Analysis of potential debris flow source areas on Mount Shasta, California, by using airborne and satellite remote sensing data

    USGS Publications Warehouse

    Crowley, J.K.; Hubbard, B.E.; Mars, J.C.

    2003-01-01

    Remote sensing data from NASA's Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) and the first spaceborne imaging spectrometer, Hyperion, show hydrothermally altered rocks mainly composed of natroalunite, kaolinite, cristobalite, and gypsum on both the Mount Shasta and Shastina cones. Field observations indicate that much of the visible altered rock consists of talus material derived from fractured rock zones within and adjacent to dacitic domes and nearby lava flows. Digital elevation data were utilized to distinguish steeply sloping altered bedrock from more gently sloping talus materials. Volume modeling based on the imagery and digital elevation data indicate that Mount Shasta drainage systems contain moderate volumes of altered rock, a result that is consistent with Mount Shasta's Holocene record of mostly small to moderate debris flows. Similar modeling for selected areas at Mount Rainier and Mount Adams, Washington, indicates larger altered rock volumes consistent with the occurrence of much larger Holocene debris flows at those volcanoes. The availability of digital elevation and spectral data from spaceborne sensors, such as Hyperion and the Advanced Spaceborne Thermal Emission and Reflectance Radiometer (ASTER), greatly expands opportunities for studying potential debris flow source characteristics at stratovolcanoes around the world. ?? 2003 Elsevier Inc. All rights reserved.

  16. Comprehensive, integrated, remote sensing at DOE sites

    SciTech Connect

    Lackey, J.G.; Burson, Z.G.

    1984-01-01

    The Department of Energy has established a program called Comprehensive, Integrated Remote Sensing (CIRS). The overall objective is to provide a state-of-the-art data base of remotely sensed data for all users of such information at large DOE sites. The primary types of remote sensing provided consist of the following: (1) large format aerial photography; (2) video from aerial platforms; (3) multispectral scanning; and (4) airborne nuclear radiometric surveys. Implementation of the CIRS Program began with field operations at the Savannah River Plant in 1982 and is continuing at that DOE site at a level of effort of about $1.5 m per year. Integrated remote sensing studies were subsequently extended to the West Valley Demonstration Project in the summer and fall of 1984. It is expected that the Program will eventually be extended to cover all large DOE sites on a continuing basis. 2 figures.

  17. Airborne remote sensing of tropospheric water vapor using a near infrared DIAL system

    NASA Technical Reports Server (NTRS)

    Ehret, G.; Kiemle, C.; Renger, W.; Simmet, G.

    1992-01-01

    Summarized here are the results of airborne water vapor measurements in the lower middle and upper troposphere using the Differential Absorption Lidar (DIAL) technique in the near infrared. The measurements were performed in July 1990 in Southern Bavaria between Allersberg and Straubing from 20 to 23 UTC taking advantage of night time conditions. The tropospheric H2O profiles were range investigated both horizontally and vertically. With the DIAL system that was used, water vapor measurements in the upper troposphere have been carried out for the first time. To calibrate the H2O-retrievals, effective absorption cross sections of selected H2O lines in terms of altitude around 724 nm were calculated using line parameter data from the literature (B. E. Grossmann et al). The frequency of the on-line measurements was adjusted by the spectra of a Polyacenic Semiconductor (PAS) cell filled with H2O. We found that the calibration error ranged between 0.005 and 0.015 cm(exp -1). The systematic errors of the H2O as a function of altitude were estimated below 7 km and 12 percent accuracy in the upper troposphere. The vertical H2O profile agrees well with in situ measurements in the investigated range between the top of the planetary boundary layer (PBL) up to near the tropopause. Horizontal and vertical H2O profiles are calculated by means of averaging single lidar returns. Typical horizontal resolutions range from 4 km in the lower to 11 km in the upper troposphere with vertical resolutions varying from 0.3 km up to 1 km, respectively, in order to satisfy a 5 - 10 percent accuracy in the statistical error. The measurement sensibility of the water vapor mixing ration in the upper troposphere is 0.01 g/kg.

  18. Assessing stream temperature variation in the Pacific Northwest using airborne thermal infrared remote sensing.

    PubMed

    Tan, Jing; Cherkauer, Keith A

    2013-01-30

    The objective of this paper is to evaluate the temporal and spatial variability of stream temperatures and how stream temperatures are affected by land use through the use of airborne thermal infrared (TIR) imagery. Both five-meter and fifteen-meter MODIS/ASTER (MASTER) imagery were acquired along the main channel of the Green-Duwamish River in Washington State, U.S. in multiple straight line passes with image overlaps occurring at time intervals of between 3 and 45 min. Five- and fifteen-meter data were collected on August 25th, 2001, with a few additional five-meter images collected on August 27th. Image overlaps were studied to evaluate the time dependence between acquisition time and observed water temperature. Temperature change between adjacent images over the course of a few minutes was found to be negligible, but became significant at times greater than 45 min, with an estimated increase in water temperature of 2-3 °C between the first and last image collected for the complete five-meter resolution survey. Images captured from different days help identify persistent localized temperature differences. While accounting for temperature changes that occurred during the acquisition process, we still found that average stream reach temperatures increased with urbanization, while variability decreased. The same occurred in the immediate presence of a reservoir. This study suggests that urbanization affects stream temperature not only through the removal of riparian zone vegetation, but also through changes to sources in in-stream variability including the presence of rocks, woody debris and sandbars. PMID:23262409

  19. Autonomous and Remote-Controlled Airborne and Ground-Based Robotic Platforms for Adaptive Geophysical Surveying

    NASA Astrophysics Data System (ADS)

    Spritzer, J. M.; Phelps, G. A.

    2011-12-01

    Low-cost autonomous and remote-controlled robotic platforms have opened the door to precision-guided geophysical surveying. Over the past two years, the U.S. Geological Survey, Senseta, NASA Ames Research Center, and Carnegie Mellon University Silicon Valley, have developed and deployed small autonomous and remotely controlled vehicles for geophysical investigations. The purpose of this line of investigation is to 1) increase the analytical capability, resolution, and repeatability, and 2) decrease the time, and potentially the cost and map-power necessary to conduct near-surface geophysical surveys. Current technology has advanced to the point where vehicles can perform geophysical surveys autonomously, freeing the geoscientist to process and analyze the incoming data in near-real time. This has enabled geoscientists to monitor survey parameters; process, analyze and interpret the incoming data; and test geophysical models in the same field session. This new approach, termed adaptive surveying, provides the geoscientist with choices of how the remainder of the survey should be conducted. Autonomous vehicles follow pre-programmed survey paths, which can be utilized to easily repeat surveys on the same path over large areas without the operator fatigue and error that plague man-powered surveys. While initial deployments with autonomous systems required a larger field crew than a man-powered survey, over time operational experience costs and man power requirements will decrease. Using a low-cost, commercially available chassis as the base for autonomous surveying robotic systems promise to provide higher precision and efficiency than human-powered techniques. An experimental survey successfully demonstrated the adaptive techniques described. A magnetic sensor was mounted on a small rover, which autonomously drove a prescribed course designed to provide an overview of the study area. Magnetic data was relayed to the base station periodically, processed and gridded. A

  20. Applications of remote sensing for water quality and biological measurements in coastal waters

    NASA Technical Reports Server (NTRS)

    Johnson, R. W.; Harriss, R. C.

    1979-01-01

    Potential applications of remote sensing technology to the study of coastal marine environments are reviewed, emphasizing water quality and biological measurements. Parameters measurable by airborne or spaceborne remote sensors include particulates, measured by visual or multispectral photography, chlorophyll a, measured by the Ocean Color Scanner or Coastal Zone Color Scanner, temperature distributions, by IR or microwave sensors, and salinity, by means of microwave radiometers. Research projects in which wide area synoptic or repetitive remote sensing can make a major contribution include the study of estuarine and continental shelf sediment transport dynamics, marine pollutant transport, marine phytoplankton dynamics and ocean fronts.

  1. Using remote sensing and ancillary data to extend airborne electromagnetic resistivity surveys for regional permafrost interpretation

    NASA Astrophysics Data System (ADS)

    Pastick, N.; Wylie, B. K.; Minsley, B. J.; Jorgenson, T. T.; Ji, L.; Walvoord, M. A.; Smith, B. D.; Abraham, J. D.; Rose, J.

    2011-12-01

    Permafrost has a significant impact on high latitude ecosystems and is spatially heterogeneous. However, only generalized maps of permafrost extent are available. Due to its impacts on subsurface hydrology, lake water levels, vegetation communities, and surface soil deformations, understanding the spatial extents and depth of permafrost are critical. Electrical resistivity increases dramatically as a soil freezes and can be used as a proxy for permafrost presence particularly if the underlying soils and geologic characteristics are understood. An airborne electromagnetic survey (AEM) was conducted over a portion of the Yukon Flats ecoregion in central Alaska with measurements taken in both reconnaissance lines and contiguous block area coverage. The AEM was flown in June 2010 and subsurface resistivity models were derived by inverting the AEM data. Landsat TM at-sensor reflectance, thermal, and spectral index data from late August to early September 2008, Digital Elevation Models (DEM) and derivatives, and other ancillary data were used in a regression tree model to predict near surface electrical resistivity at the 0-1m and the 0-2.6m depth intervals. AEM locations from homogenous landsat 90 m by 90 m windows were randomly separated into a training set for model development (n = 8,848) and an impendent test data set (n = 988) for model accuracy assessment. Model development and independent test accuracies for 0-1 m electric resistivity had training and test R2 values of 0.90 and 0.87, respectively, and for the 0-2.6m electric resistivity training and test R2 values were also 0.90 and 0.87, respectively, which indicated accurate prediction models. Important variables for stratifying the various piecewise regressions were elevation and averaged 2000-2008 ecosystem performance anomalies. Important independent variables used in the multiple regression equations were the Normalized Difference Infrared Index (NDII), NDII7 (NDII using band 7), soil moisture mapped from

  2. A Decade Remote Sensing River Bathymetry with the Experimental Advanced Airborne Research LiDAR

    NASA Astrophysics Data System (ADS)

    Kinzel, P. J.; Legleiter, C. J.; Nelson, J. M.; Skinner, K.

    2012-12-01

    Since 2002, the first generation of the Experimental Advanced Airborne Research LiDAR (EAARL-A) sensor has been deployed for mapping rivers and streams. We present and summarize the results of comparisons between ground truth surveys and bathymetry collected by the EAARL-A sensor in a suite of rivers across the United States. These comparisons include reaches on the Platte River (NE), Boise and Deadwood Rivers (ID), Blue and Colorado Rivers (CO), Klamath and Trinity Rivers (CA), and the Shenandoah River (VA). In addition to diverse channel morphologies (braided, single thread, and meandering) these rivers possess a variety of substrates (sand, gravel, and bedrock) and a wide range of optical characteristics which influence the attenuation and scattering of laser energy through the water column. Root mean square errors between ground truth elevations and those measured by the EAARL-A ranged from 0.15-m in rivers with relatively low turbidity and highly reflective sandy bottoms to over 0.5-m in turbid rivers with less reflective substrates. Mapping accuracy with the EAARL-A has proved challenging in pools where bottom returns are either absent in waveforms or are of such low intensity that they are treated as noise by waveform processing algorithms. Resolving bathymetry in shallow depths where near surface and bottom returns are typically convolved also presents difficulties for waveform processing routines. The results of these evaluations provide an empirical framework to discuss the capabilities and limitations of the EAARL-A sensor as well as previous generations of post-processing software for extracting bathymetry from complex waveforms. These experiences and field studies not only provide benchmarks for the evaluation of the next generation of bathymetric LiDARs for use in river mapping, but also highlight the importance of developing and standardizing more rigorous methods to characterize substrate reflectance and in-situ optical properties at study sites

  3. Atmospheric profiles of Black Carbon at remote locations using light-weight airborne Aethalometers

    NASA Astrophysics Data System (ADS)

    Hansen, A. D.; Močnik, G.; Drinovec, L.; Lenarcic, M.

    2012-12-01

    While measurements of atmospheric aerosols are routinely performed at ground-level around the world, there is far less knowledge of their concentrations at altitude: yet this data is a crucial requirement for our understanding of the dispersion of pollutants of anthropogenic origin, with their associated effects on radiative forcing, cloud condensation, and other adverse phenomena. Black Carbon (BC) is a unique tracer for combustion emissions, and can be detected rapidly and with great sensitivity by filter-based optical methods. It has no non-combustion sources and is not transformed by atmospheric processes. Recent technical advances have developed light-weight miniaturized instruments which can be operated on light aircraft or carried aboard commercial passenger flights. From January to April 2012, a single-seat ultra-light aircraft flew around the world on a scientific, photographic and environmental-awareness mission. The flight track crossed all seven continents and all major oceans, with altitudes up to 8.9 km ASL. The aircraft carried a custom-developed high-sensitivity dual-wavelength light-weight Aethalometer, operating at 370 and 880 nm with special provision to compensate for the effects of changing pressure, temperature and humidity. The instrument recorded BC concentrations with high temporal resolution and sensitivity better than 5 ng/m3. We present examples of data from flight tracks over remote oceans, uninhabited land masses, and densely populated areas, analyzing the spectral dependence of absorption to infer the contributions to BC from fossil fuel vs. biomass combustion, and aggregating the data into vertical profiles. The regional and long range transport of BC may be investigated using back-trajectories. We have also operated miniature instruments in the passenger cabins of long-distance commercial aircraft. Since there are no combustion sources within the cabin, any BC in the ventilation air must necessarily have originated from the outside

  4. Airborne passive remote sensing of large-scale methane emissions from oil fields in California's San Joaquin Valley and validation by airborne in-situ measurements - Initial results from COMEX

    NASA Astrophysics Data System (ADS)

    Gerilowski, Konstantin; Krautwurst, Sven; Kolyer, Richard W.; Thompson, David R.; Jonsson, Haflidi; Krings, Thomas; Horstjann, Markus; Leifer, Ira; Eastwood, Michael; Green, Robert O.; Vigil, Sam; Schüttemeyer, Dirk; Fladeland, Matthew; Burrows, John P.; Bovensmann, Heinrich

    2015-04-01

    On several flights performed over the Kern River, Kern Front, and Poso Creek Oil Fields in California between June 3 and September 4, 2014, in the framework of the CO2 and MEthane Experiment (COMEX) - a NASA and ESA funded campaign in support of the HyspIRI and CarbonSat mission definition activities - the Methane Airborne MAPper (MAMAP) remote sensing instrument (operated by the University of Bremen in cooperation with the German Research Centre for Geosciences - GFZ) detected large-scale, high-concentration, methane plumes. MAMAP was installed for the flights aboard the Center for Interdisciplinary Remotely-Piloted Aircraft Studies (CIRPAS) Twin Otter aircraft, together with a Picarro fast in-situ greenhouse gas (GHG) analyzer (operated by the NASA Ames Research Center, ARC), a 5-hole turbulence probe and an atmospheric measurement package (operated by CIRPAS), measuring aerosols, temperature, dew-point, and other atmospheric parameters. Some of the flights were accompanied by the next generation of the Airborne Visible InfraRed Imaging Spectrometer (AVIRIS-NG), operated by the Jet Propulsion Laboratory (JPL), California Institute of Technology, installed aboard a second Twin Otter aircraft (operated by Twin Otter International). Data collected with the in-situ GHG analyzer were used for validation of the MAMAP and AVIRIS-NG remotely sensed data. The in-situ measurements were acquired in vertical cross sections of the discovered plumes at fixed distances downwind of the sources. Emission rates are estimated from both the remote and in-situ data using wind information from the turbulence probe together with ground-based wind data from the nearby airport. Remote sensing and in-situ data as well as initial flux estimates for selected flights will be presented.

  5. Study on multispectral imaging detection and recognition

    NASA Astrophysics Data System (ADS)

    Jun, Wang; Na, Ding; Gao, Jiaobo; Yu, Hu; Jun, Wu; Li, Junna; Zheng, Yawei; Fei, Gao; Sun, Kefeng

    2009-07-01

    Multispectral imaging detecting technology use target radiation character in spectral spatial distribution and relation between spectral and image to detect target and remote sensing measure. Its speciality is multi channel, narrow bandwidth, large amount of information, high accuracy. The ability of detecting target in environment of clutter, camouflage, concealment and beguilement is improved. At present, spectral imaging technology in the range of multispectral and hyperspectral develop greatly. The multispectral imaging equipment of unmanned aerial vehicle can be used in mine detection, information, surveillance and reconnaissance. Spectral imaging spectrometer operating in MWIR and LWIR has already been applied in the field of remote sensing and military in the advanced country. The paper presents the technology of multispectral imaging. It can enhance the reflectance, scatter and radiation character of the artificial targets among nature background. The targets among complex background and camouflage/stealth targets can be effectively identified. The experiment results and the data of spectral imaging is obtained.

  6. Acute health impacts of airborne particles estimated from satellite remote sensing.

    PubMed

    Wang, Zhaoxi; Liu, Yang; Hu, Mu; Pan, Xiaochuan; Shi, Jing; Chen, Feng; He, Kebin; Koutrakis, Petros; Christiani, David C

    2013-01-01

    Satellite-based remote sensing provides a unique opportunity to monitor air quality from space at global, continental, national and regional scales. Most current research focused on developing empirical models using ground measurements of the ambient particulate. However, the application of satellite-based exposure assessment in environmental health is still limited, especially for acute effects, because the development of satellite PM(2.5) model depends on the availability of ground measurements. We tested the hypothesis that MODIS AOD (aerosol optical depth) exposure estimates, obtained from NASA satellites, are directly associated with daily health outcomes. Three independent healthcare databases were used: unscheduled outpatient visits, hospital admissions, and mortality collected in Beijing metropolitan area, China during 2006. We use generalized linear models to compare the short-term effects of air pollution assessed by ground monitoring (PM(10)) with adjustment of absolute humidity (AH) and AH-calibrated AOD. Across all databases we found that both AH-calibrated AOD and PM(10) (adjusted by AH) were consistently associated with elevated daily events on the current day and/or lag days for cardiovascular diseases, ischemic heart diseases, and COPD. The relative risks estimated by AH-calibrated AOD and PM(10) (adjusted by AH) were similar. Additionally, compared to ground PM(10), we found that AH-calibrated AOD had narrower confidence intervals for all models and was more robust in estimating the current day and lag day effects. Our preliminary findings suggested that, with proper adjustment of meteorological factors, satellite AOD can be used directly to estimate the acute health impacts of ambient particles without prior calibrating to the sparse ground monitoring networks. PMID:23220016

  7. Acute health impacts of airborne particles estimated from satellite remote sensing✩

    PubMed Central

    Wang, Zhaoxi; Liu, Yang; Hu, Mu; Pan, Xiaochuan; Shi, Jing; Chen, Feng; He, Kebin; Koutrakis, Petros; Christiani, David C.

    2013-01-01

    Satellite-based remote sensing provides a unique opportunity to monitor air quality from space at global, continental, national and regional scales. Most current research focused on developing empirical models using ground measurements of the ambient particulate. However, the application of satellite-based exposure assessment in environmental health is still limited, especially for acute effects, because the development of satellite PM2.5 model depends on the availability of ground measurements. We tested the hypothesis that MODIS AOD (aerosol optical depth) exposure estimates, obtained from NASA satellites, are directly associated with daily health outcomes. Three independent healthcare databases were used: unscheduled outpatient visits, hospital admissions, and mortality collected in Beijing metropolitan area, China during 2006. We use generalized linear models to compare the short-term effects of air pollution assessed by ground monitoring (PM10) with adjustment of absolute humidity (AH) and AH-calibrated AOD. Across all databases we found that both AH-calibrated AOD and PM10 (adjusted by AH) were consistently associated with elevated daily events on the current day and/or lag days for cardiovascular diseases, ischemic heart diseases, and COPD. The relative risks estimated by AH-calibrated AOD and PM10 (adjusted by AH) were similar. Additionally, compared to ground PM10, we found that AH-calibrated AOD had narrower confidence intervals for all models and was more robust in estimating the current day and lag day effects. Our preliminary findings suggested that, with proper adjustment of meteorological factors, satellite AOD can be used directly to estimate the acute health impacts of ambient particles without prior calibrating to the sparse ground monitoring networks. PMID:23220016

  8. Concept and integration of an on-line quasi-operational airborne hyperspectral remote sensing system

    NASA Astrophysics Data System (ADS)

    Schilling, Hendrik; Lenz, Andreas; Gross, Wolfgang; Perpeet, Dominik; Wuttke, Sebastian; Middelmann, Wolfgang

    2013-10-01

    Modern mission characteristics require the use of advanced imaging sensors in reconnaissance. In particular, high spatial and high spectral resolution imaging provides promising data for many tasks such as classification and detecting objects of military relevance, such as camouflaged units or improvised explosive devices (IEDs). Especially in asymmetric warfare with highly mobile forces, intelligence, surveillance and reconnaissance (ISR) needs to be available close to real-time. This demands the use of unmanned aerial vehicles (UAVs) in combination with downlink capability. The system described in this contribution is integrated in a wing pod for ease of installation and calibration. It is designed for the real-time acquisition and analysis of hyperspectral data. The main component is a Specim AISA Eagle II hyperspectral sensor, covering the visible and near-infrared (VNIR) spectral range with a spectral resolution up to 1.2 nm and 1024 pixel across track, leading to a ground sampling distance below 1 m at typical altitudes. The push broom characteristic of the hyperspectral sensor demands an inertial navigation system (INS) for rectification and georeferencing of the image data. Additional sensors are a high resolution RGB (HR-RGB) frame camera and a thermal imaging camera. For on-line application, the data is preselected, compressed and transmitted to the ground control station (GCS) by an existing system in a second wing pod. The final result after data processing in the GCS is a hyperspectral orthorectified GeoTIFF, which is filed in the ERDAS APOLLO geographical information system. APOLLO allows remote access to the data and offers web-based analysis tools. The system is quasi-operational and was successfully tested in May 2013 in Bremerhaven, Germany.

  9. Husbandry Trace Gas Emissions from a Dairy Complex By Mobile in Situ and Airborne and Spaceborne Remote Sensing: A Comex Campaign Focus

    NASA Astrophysics Data System (ADS)

    Leifer, I.; Tratt, D. M.; Bovensmann, H.; Buckland, K. N.; Burrows, J. P.; Frash, J.; Gerilowski, K.; Iraci, L. T.; Johnson, P. D.; Kolyer, R.; Krautwurst, S.; Krings, T.; Leen, J. B.; Hu, C.; Melton, C.; Vigil, S. A.; Yates, E. L.; Zhang, M.

    2014-12-01

    Recent field study reviews on the greenhouse gas methane (CH4) found significant underestimation from fossil fuel industry and husbandry. The 2014 COMEX campaign seeks to develop methods to derive CH4 and carbon dioxide (CO2) from remote sensing data by combining hyperspectral imaging (HSI) and non-imaging spectroscopy (NIS) with in situ airborne and surface data. COMEX leverages synergies between high spatial resolution HSI column abundance maps and moderate spectral/spatial resolution NIS. Airborne husbandry data were collected for the Chino dairy complex (East Los Angeles Basin) by NIS-MAMAP, HSI-Mako thermal-infrared (TIR); AVIRIS NG shortwave IR (SWIR), with in situ surface mobile-AMOG Surveyor (AutoMObile greenhouse Gas)-and airborne in situ from a Twin Otter and the AlphaJet. AMOG Surveyor uses in situ Integrated Cavity Off Axis Spectroscopy (OA-ICOS) to measure CH4, CO2, H2O, H2S and NH3 at 5-10 Hz, 2D winds, and thermal anomaly in an adapted commuter car. OA-ICOS provides high precision and accuracy with excellent stability. NH3 and CH4 emissions were correlated at dairy size-scales but not sub-dairy scales in surface and Mako data, showing fine-scale structure and large variations between the numerous dairies in the complex (herd ~200,000-250,000) embedded in an urban setting. Emissions hotspots were consistent between surface and airborne surveys. In June, surface and MAMAP data showed a weak overall plume, while surface and Mako data showed a stronger plume in late (hotter) July. Multiple surface plume transects using NH3 fingerprinting showed East and then NE advection out of the LA Basin consistent with airborne data. Long-term trends were investigated in satellite data. This study shows the value of synergistically combined NH3 and CH4 remote sensing data to the task of CH4 source attribution using airborne and space-based remote sensing (IASI for NH3) and top of atmosphere sensitivity calculations for Sentinel V and Carbon Sat (CH4).

  10. Airborne Multi-wavelength High Spectral Resolution Lidar for Process Studies and Assessment of Future Satellite Remote Sensing Concepts

    NASA Astrophysics Data System (ADS)

    Hostetler, C. A.; Ferrare, R. A.; Hair, J. W.; Cook, A. L.; Harper, D. B.; Mack, T. L.; Hare, R. J.; Cleckner, C. S.; Rogers, R.; Mueller, D.; Chemyakin, E.; Burton, S. P.; Obland, M. D.; Scarino, A. J.; Cairns, B.; Russell, P. B.; Redemann, J.; Shinozuka, Y.; Schmid, B.; Berg, L. K.; Fast, J. D.; Flynn, C. J.

    2012-12-01

    NASA Langley recently developed the world's first airborne multi-wavelength high spectral resolution lidar (HSRL). This lidar employs the HSRL technique at 355 and 532 nm to make independent, unambiguous retrievals of aerosol extinction and backscatter. It also employs the standard backscatter technique at 1064 nm and is polarization-sensitive at all three wavelengths. This instrument, dubbed HSRL-2 (the second-generation HSRL developed by NASA Langley), is a prototype for the lidar on NASA's planned Aerosols-Clouds-Ecosystems (ACE) mission. HSRL-2 completed its first science mission in July 2012, the Two-Column Aerosol Project (TCAP) conducted by the Department of Energy (DOE) in Hyannis, MA. TCAP presents an excellent opportunity to assess some of the remote sensing concepts planned for ACE: HSRL-2 was deployed on the Langley King Air aircraft with another ACE-relevant instrument, the NASA GISS Research Scanning Polarimeter (RSP), and flights were closely coordinated with the DOE's Gulfstream-1 aircraft, which deployed a variety of in situ aerosol and trace gas instruments and the new Spectrometer for Sky-Scanning, Sun-Tracking Atmospheric Research (4STAR). The DOE also deployed their Atmospheric Radiation Measurement Mobile Facility and their Mobile Aerosol Observing System at a ground site located on the northeastern coast of Cape Cod for this mission. In this presentation we focus on the capabilities, data products, and applications of the new HSRL-2 instrument. Data products include aerosol extinction, backscatter, depolarization, and optical depth; aerosol type identification; mixed layer depth; and range-resolved aerosol microphysical parameters (e.g., effective radius, index of refraction, single scatter albedo, and concentration). Applications include radiative closure studies, studies of aerosol direct and indirect effects, investigations of aerosol-cloud interactions, assessment of chemical transport models, air quality studies, present (e.g., CALIPSO

  11. Identifying trout refuges in the Indian and Hudson Rivers in northern New York through airborne thermal infrared remote sensing

    USGS Publications Warehouse

    Ernst, Anne G.; Baldigo, Barry P.; Calef, Fred J.; Freehafer, Douglas A.; Kremens, Robert L.

    2015-01-01

    The locations and sizes of potential cold-water refuges for trout were examined in 2005 along a 27-kilometer segment of the Indian and Hudson Rivers in northern New York to evaluate the extent of refuges, the effects of routine flow releases from an impoundment, and how these refuges and releases might influence trout survival in reaches that otherwise would be thermally stressed. This river segment supports small populations of brook trout (Salvelinus fontinalis), brown trout (Salmo trutta), and rainbow trout (Oncorhynchus mykiss) and also receives regular releases of reservoir-surface waters to support rafting during the summer, when water temperatures in both the reservoir and the river frequently exceed thermal thresholds for trout survival. Airborne thermal infrared imaging was supplemented with continuous, in-stream temperature loggers to identify potential refuges that may be associated with tributary inflows or groundwater seeps and to define the extent to which the release flows decrease the size of existing refuges. In general, the release flows overwhelmed the refuge areas and greatly decreased the size and number of the areas. Mean water temperatures were unaffected by the releases, but small-scale heterogeneity was diminished. At a larger scale, water temperatures in the upper and lower segments of the reach were consistently warmer than in the middle segment, even during passage of release waters. The inability of remote thermal infrared images to consistently distinguish land from water (in shaded areas) and to detect groundwater seeps (away from the shallow edges of the stream) limited data analysis and the ability to identify potential thermal refuge areas.

  12. Airborne Remote-Sensing of Atmoshperic CH4 and CO2 Column Mixing Ratio With MAMap - First Results

    NASA Astrophysics Data System (ADS)

    Tretner, A.; Gerilowski, K.; Bovensmann, H.; Buchwitz, M.; Erzinger, J.; Burrows, J.

    2007-12-01

    The Methane Airborne Mapper (MAMap) performs quantitative CO2 and CH4 remote sensing measurements of the atmospheric column between an aircraft and the Earth's surface. Its two spectrometers cover wavelenghts of 1.59-1.62μm for CO2, 1.63-1.75μm for CH4 and 760nm for O2. A CH4 detection limit of <35ppbv and a resolution of <5% (at atmospheric background concentration of 1750ppbv) have been ascertained, which makes it possible to detect small changes within the atmospheric CH4 column at a local and regional scale. The atmospheric column mixing ratios of CH4 and CO2 were calculated using the WFM-DOAS algorithm which is known from the retrieval of CH4 and CO2 column concentrations from nadir measurements by SCIAMACHY. MAMap addresses the uncertainties in the current greenhouse gas emission budgets and provides a link between local ground-based small-scale and global satellite-based measurements. The aim of future MAMap research programs is the detection and quantification of CH4 and CO2 emission sources of both natural and anthropogenic origin. MAMap is designed for flexible operations at various planes, e.g. the DLR Dornier 228, the DLR 'Falcon' or the DLR Gulfstream 'HALO' aircraft. The results presented here were performed with a Cessna aircraft T207 at a flight height of 700m and a flight speed of 200km/h. The related ground pixel size covers 18m (across-track) x 10m (along track, albedo 0.18). The preliminary assessment of the sensor sensitivity under field campaign conditions includes measurements over a variety of natural and anthropogenic CH4 and CO2 emission sources, like coal-fired power plants, landfill sites, wetlands, a large number of different land surface types and a simulated CH4 source (CH4 released from a pressured gas bottle). First results will be reported.

  13. Fusion of full waveform Laserscanning and airborne hyperspectral remote sensing data for the characterization of forest stands

    NASA Astrophysics Data System (ADS)

    Buddenbaum, Henning

    2010-05-01

    Hyperspectral data offer the maximum spectral reflectance information available from remote sensing. A continuous spectrum of narrow bands with near-laboratory quality is recorded for each pixel. This data can be used for difficult classification tasks or detailed quantitative analyses, e.g. determination of chlorophyll or water content in leaves. But in forested areas, discerning between different age classes of the same tree species is still error-prone. Airborne Laserscanning measures the three-dimensional position of every reflecting object and can be used to map tree heights and crown volumes. These are highly correlated with tree age and timber volume. In addition, Laserscanner data can be used to differentiate between coniferous and deciduous trees either by analysing crown shapes that lead to different surface roughness or by exploiting the intensity information of laser echoes from the crowns. But a more detailed determination of tree species is not possible using Laserscanning alone. The combination of hyperspectral and Laserscanning data promises the possibility to map both tree species and age classes. We used a HyMap data set with 122 bands recorded in 2003 and a full waveform Laserscanning recorded in 2005 in the same area, Idarwald Forest in South-western Germany. To combine both datasets, we defined voxels above the HyMap pixels, containing the mean laser intensity in slices of 50 cm height. These voxels form a second hyperspectral dataset of 76 bands with the same geometry as the HyMap image, so that they could be fused into a 198 band image. The joined image performed better in a classification of tree species and age classes than each of the single images and also better than a dataset consisting of the hyperspectral image and a tree height map. Apart from classification, it can also be used to derive tree heights and crown base heights and to estimate biomass, leaf area index and timber volume and to characterize the vertical forest structure.

  14. Selectable Hyperspectral Airborne Remote-sensing Kit (SHARK) on the Vision II turbine rotorcraft UAV over the Florida Keys

    NASA Astrophysics Data System (ADS)

    Holasek, R. E.; Nakanishi, K.; Swartz, B.; Zacaroli, R.; Hill, B.; Naungayan, J.; Herwitz, S.; Kavros, P.; English, D. C.

    2013-12-01

    As part of the NASA ROSES program, the NovaSol Selectable Hyperspectral Airborne Remote-sensing Kit (SHARK) was flown as the payload on the unmanned Vision II helicopter. The goal of the May 2013 data collection was to obtain high resolution visible and near-infrared (visNIR) hyperspectral data of seagrasses and coral reefs in the Florida Keys. The specifications of the SHARK hyperspectral system and the Vision II turbine rotorcraft will be described along with the process of integrating the payload to the vehicle platform. The minimal size, weight, and power (SWaP) specifications of the SHARK system is an ideal match to the Vision II helicopter and its flight parameters. One advantage of the helicopter over fixed wing platforms is its inherent ability to take off and land in a limited area and without a runway, enabling the UAV to be located in close proximity to the experiment areas and the science team. Decisions regarding integration times, waypoint selection, mission duration, and mission frequency are able to be based upon the local environmental conditions and can be modified just prior to take off. The operational procedures and coordination between the UAV pilot, payload operator, and scientist will be described. The SHARK system includes an inertial navigation system and digital elevation model (DEM) which allows image coordinates to be calculated onboard the aircraft in real-time. Examples of the geo-registered images from the data collection will be shown. SHARK mounted below VTUAV. SHARK deployed on VTUAV over water.

  15. JORNEX: An airborne campaign to quantify rangeland vegetation change and plant community-atmospheric interactions

    SciTech Connect

    Ritchie, J.C.; Rango, A.; Kustas, W.P.

    1996-11-01

    The Jornada Experimental Range in New Mexico provides a unique opportunity to integrate hydrologic-atmospheric fluxes and surface states, vegetation types, cover, and distribution, and vegetation response to changes in hydrologic states and atmospheric driving forces. The Jornada Range is the site of a long-term ecological research program to investigate the processes leading to desertification. In concert with ongoing ground measurements, remotely sensed data are being collected from ground, airborne, and satellite platforms during JORNEX (the JORNada Experiment) to provide spatial and temporal distribution of vegetation state using laser altimeter and multispectral aircraft and satellite data and surface energy balance estimates from a combination of parameters and state variables derived from remotely sensed data. These measurements will be used as inputs to models to quantify the hydrologic budget and the plant response to changes in components in the water and energy balance. Intensive three day study periods for ground and airborne campaigns have been made in May 1995 (dry season) and September 1995 (wet season), February 1996 (Winter) and are planned for wet and dry seasons of 1996. An airborne platform is being used to collect thermal, multispectral, 3-band video, and laser altimetry profile data. Bowen ratio-energy balance stations were established in shrub and grass communities in May 1995 and are collecting data continuously. Additional energy flux measurements were made using eddy correlation techniques during the September 1995 campaign. Ground-based measurements during the intensive campaigns include thermal and multispectral measurements made using yoke-based platforms and hand-held instruments, LAI, and other vegetation data. Ground and aircraft measurements are acquired during Landsat overpasses so the effect of scale on measurements can be studied. This paper discusses preliminary results from the 1995 airborne campaign. 24 refs., 13 figs., 1 tab.

  16. Using airborne HIAPER Pole-to-Pole Observations (HIPPO) to evaluate model and remote sensing estimates of atmospheric carbon dioxide

    NASA Astrophysics Data System (ADS)

    Frankenberg, Christian; Kulawik, Susan S.; Wofsy, Steven C.; Chevallier, Frédéric; Daube, Bruce; Kort, Eric A.; O'Dell, Christopher; Olsen, Edward T.; Osterman, Gregory

    2016-06-01

    In recent years, space-borne observations of atmospheric carbon dioxide (CO2) have been increasingly used in global carbon-cycle studies. In order to obtain added value from space-borne measurements, they have to suffice stringent accuracy and precision requirements, with the latter being less crucial as it can be reduced by just enhanced sample size. Validation of CO2 column-averaged dry air mole fractions (XCO2) heavily relies on measurements of the Total Carbon Column Observing Network (TCCON). Owing to the sparseness of the network and the requirements imposed on space-based measurements, independent additional validation is highly valuable. Here, we use observations from the High-Performance Instrumented Airborne Platform for Environmental Research (HIAPER) Pole-to-Pole Observations (HIPPO) flights from 01/2009 through 09/2011 to validate CO2 measurements from satellites (Greenhouse Gases Observing Satellite - GOSAT, Thermal Emission Sounder - TES, Atmospheric Infrared Sounder - AIRS) and atmospheric inversion models (CarbonTracker CT2013B, Monitoring Atmospheric Composition and Climate (MACC) v13r1). We find that the atmospheric models capture the XCO2 variability observed in HIPPO flights very well, with correlation coefficients (r2) of 0.93 and 0.95 for CT2013B and MACC, respectively. Some larger discrepancies can be observed in profile comparisons at higher latitudes, in particular at 300 hPa during the peaks of either carbon uptake or release. These deviations can be up to 4 ppm and hint at misrepresentation of vertical transport. Comparisons with the GOSAT satellite are of comparable quality, with an r2 of 0.85, a mean bias μ of -0.06 ppm, and a standard deviation σ of 0.45 ppm. TES exhibits an r2 of 0.75, μ of 0.34 ppm, and σ of 1.13 ppm. For AIRS, we find an r2 of 0.37, μ of 1.11 ppm, and σ of 1.46 ppm, with latitude-dependent biases. For these comparisons at least 6, 20, and 50 atmospheric soundings have been averaged for GOSAT, TES, and AIRS

  17. Investigation related to multispectral imaging systems

    NASA Technical Reports Server (NTRS)

    Nalepka, R. F.; Erickson, J. D.

    1974-01-01

    A summary of technical progress made during a five year research program directed toward the development of operational information systems based on multispectral sensing and the use of these systems in earth-resource survey applications is presented. Efforts were undertaken during this program to: (1) improve the basic understanding of the many facets of multispectral remote sensing, (2) develop methods for improving the accuracy of information generated by remote sensing systems, (3) improve the efficiency of data processing and information extraction techniques to enhance the cost-effectiveness of remote sensing systems, (4) investigate additional problems having potential remote sensing solutions, and (5) apply the existing and developing technology for specific users and document and transfer that technology to the remote sensing community.

  18. High fidelity remote sensing of snow properties from MODIS and the Airborne Snow Observatory: Snowflakes to Terabytes

    NASA Astrophysics Data System (ADS)

    Painter, T.; Mattmann, C. A.; Brodzik, M.; Bryant, A. C.; Goodale, C. E.; Hart, A. F.; Ramirez, P.; Rittger, K. E.; Seidel, F. C.; Zimdars, P. A.

    2012-12-01

    The response of the cryosphere to climate forcings largely determines Earth's climate sensitivity. However, our understanding of the strength of the simulated snow albedo feedback varies by a factor of three in the GCMs used in the Fourth Assessment Report of the Intergovernmental Panel on Climate Change, mainly caused by uncertainties in snow extent and the albedo of snow-covered areas from imprecise remote sensing retrievals. Additionally, the Western US and other regions of the globe depend predominantly on snowmelt for their water supply to agriculture, industry and cities, hydroelectric power, and recreation, against rising demand from increasing population. In the mountains of the Upper Colorado River Basin, dust radiative forcing in snow shortens snow cover duration by 3-7 weeks. Extended to the entire upper basin, the 5-fold increase in dust load since the late-1800s results in a 3-week earlier peak runoff and a 5% annual loss of total runoff. The remotely sensed dynamics of snow cover duration and melt however have not been factored into hydrological modeling, operational forecasting, and policymaking. To address these deficiencies in our understanding of snow properties, we have developed and validated a suite of MODIS snow products that provide accurate fractional snow covered area and radiative forcing of dust and carbonaceous aerosols in snow. The MODIS Snow Covered Area and Grain size (MODSCAG) and MODIS Dust Radiative Forcing in Snow (MODDRFS) algorithms, developed and transferred from imaging spectroscopy techniques, leverage the complete MODIS surface reflectance spectrum. The two most critical properties for understanding snowmelt runoff and timing are the spatial and temporal distributions of snow water equivalent (SWE) and snow albedo. We have created the Airborne Snow Observatory (ASO), an imaging spectrometer and scanning LiDAR system, to quantify SWE and snow albedo, generate unprecedented knowledge of snow properties, and provide complete

  19. Modeling of estuarne chlorophyll a from an airborne scanner

    USGS Publications Warehouse

    Khorram, Siamak; Catts, Glenn P.; Cloern, James E.; Knight, Allen W.

    1987-01-01

    Near simultaneous collection of 34 surface water samples and airborne multispectral scanner data provided input for regression models developed to predict surface concentrations of estuarine chlorophyll a. Two wavelength ratios were employed in model development. The ratios werechosen to capitalize on the spectral characteristics of chlorophyll a, while minimizing atmospheric influences. Models were then applied to data previously acquired over the study area thre years earlier. Results are in the form of color-coded displays of predicted chlorophyll a concentrations and comparisons of the agreement among measured surface samples and predictions basedon coincident remotely sensed data. The influence of large variations in fresh-water inflow to the estuary are clearly apparent in the results. The synoptic view provided by remote sensing is another method of examining important estuarine dynamics difficult to observe from in situ sampling alone.

  20. Application of Remote Sensing Techniques for Appraising Changes in Wildlife Habitat

    NASA Technical Reports Server (NTRS)

    Nelson, H. K.; Klett, A. T.; Johnston, J. E.

    1971-01-01

    An attempt was made to investigate the potential of airborne, multispectral, line scanner data acquisition and computer-implemented automatic recognition techniques for providing useful information about waterfowl breeding habitat in North Dakota. The spectral characteristics of the components of a landscape containing waterfowl habitat can be detected with airborne scanners. By analyzing these spectral characteristics it is possible to identify and map the landscape components through analog and digital processing methods. At the present stage of development multispectral remote sensing techniques are not ready for operational application to surveys of migratory bird habitat and other such resources. Further developments are needed to: (1) increase accuracy; (2) decrease retrieval and processing time; and (3) reduce costs.

  1. Extended ocular hazard distances associated with intrabeam aided viewing of the Sandia remote sensing system, airborne aura laser (Big Sky Variant).

    SciTech Connect

    Augustoni, Arnold L.

    2004-08-01

    A laser hazard analysis to determine the Extended Ocular Hazard Distances associated with a possible intrabeam aided viewing of the Sandia Remote Sensing System (SRSS) airborne AURA laser (Big Sky Laser Technology) was performed based on the 2000 version of the American National Standard Institute's (ANSI) Standard Z136.1, for the Safe Use of Lasers and the 2000 version of the ANSI Standard Z136.6, for the Safe Use of Lasers Outdoors. The AURA lidar system is installed in the instrument pod of a Proteus airframe and is used to perform laser interaction experiments and tests at various national test sites. The targets are located at various distances (ranges) from the airborne platform. Nominal Ocular Hazard Distance (NOHD) and maximum ''eye-safe'' dwell times for various operational altitudes associated with unaided intrabeam exposure of ground personnel were determined and presented in a previous SAND report. Although the target areas are controlled and the use of viewing aids are prohibited there is the possibility of the unauthorized use of viewing aids such as binoculars. This aided viewing hazard analysis is supplemental to the previous SAND report for the laser hazard analysis of the airborne AURA.

  2. The information of oil and gas micro-seepage in Dongsheng region of inner Mongolia based on the airborne hyperspectral remote sensing image

    NASA Astrophysics Data System (ADS)

    Tian, Shu-Fang; Chen, Jian-Ping; Zhou, Mi

    2008-11-01

    The technology of hyper-spectral remote sensing which has higher spatial resolution characteristic, and optimizes the qualification of identifying and extracting salt mines, not only enhances the capacity of natural scenes detection and recognition, but also advances the level of quantitative remote sensing. It has important meaning for using the technology of hyper-spectral remote sensing to quantitative extraction. The paper investigate gas micro-seepage based on the Airborne Hyper-spectral Remote Sensing in Dongsheng of Inner Mongolia on the basis of gas micro-seepage theory using EO-1 Hyperion data collected by Satellite-Borne Sensor which has highest spatial resolution presently in the world. On the basis of data pretreated this paper adopts band math extracted the distribution of oil and gas micro-seepage using diagnostic assimilating spectrum of alteration minerals by the numbers. With eigenvector length model evaluates the research area comprehensive index, oil and gas micro-seepage information model of the research area is established and key regions of oil and gas micro-seepage are confirmed, which offers academic gist for oil and gas resource exploitation of Dongsheng.

  3. Determination of the age of oil palm from crown projection area detected from WorldView-2 multispectral remote sensing data: The case of Ejisu-Juaben district, Ghana

    NASA Astrophysics Data System (ADS)

    Chemura, Abel; van Duren, Iris; van Leeuwen, Louise M.

    2015-02-01

    Information about age of oil palm is important in sustainability assessments, carbon mapping, yield projections and precision agriculture. The aim of this study was to develop and test an approach to determine the age of oil palm plantations (years after planting) by combining high resolution multispectral remote sensing data and regression techniques using a case study of Ejisu-Juaben district of Ghana. Firstly, we determined the relationship between age and crown projection area of oil palms from sample fields. Secondly, we did hierarchical classification using object based image analysis techniques on WorldView-2 multispectral data to determine the crown projection areas of oil palms from remote sensing data. Finally, the crown projection areas obtained from the hierarchical classification were combined with the field-developed regression model to determine the age of oil palms at field level for a wider area. Field collected data showed a strong linear relationship between age and crown area of oil palm up to 13 years beyond which no relationship was observed. A user's accuracy of 80.6% and a producer's accuracy of 68.4% were obtained for the delineation of oil palm crowns while for delineation of non-crown objects a user's accuracy of 65.6% and a producer's accuracy of 78.6% were obtained, with an overall accuracy of 72.8% for the OBIA delineation. Automatic crown projection area delineation from remote sensing data produced crown projection areas which closely matched the field measured crown areas except for older oil palms (13+ years) where the error was greatest. Combining the remote sensing detected crown projection area and the regression model accurately estimated oil palm ages for 27.9% of the fields and had an estimation error of 1 year or less for 74.6% of the fields and an error of a maximum 2 years for 92.4% of the fields. The results showed that 6 and 11 year old oil palm stands were dominating age categories in the study area. Although the method

  4. Airborne and ground-based remote sensing for the estimation of evapotranspiration and yield of bean, potato, and sugar beet crops

    NASA Astrophysics Data System (ADS)

    Jayanthi, Harikishan

    compared with the actual yields extracted from the ground. The remote sensing-derived yields compared well with the actual yields sampled on the ground. This research has highlighted the importance of the date of spectral emergence, the need to know the duration for which the crops stand on the ground, and the need to identify critical periods of time when multispectral coverages are essential for reliable tuber yield estimation.

  5. CNR LARA project, Italy: Airborne laboratory for environmental research

    NASA Technical Reports Server (NTRS)

    Bianchi, R.; Cavalli, R. M.; Fiumi, L.; Marino, C. M.; Pignatti, S.

    1995-01-01

    The increasing interest for the environmental problems and the study of the impact on the environment due to antropic activity produced an enhancement of remote sensing applications. The Italian National Research Council (CNR) established a new laboratory for airborne hyperspectral imaging, the LARA Project (Laboratorio Aero per Ricerche Ambientali - Airborne Laboratory for Environmental Research), equipping its airborne laboratory, a CASA-212, mainly with the Daedalus AA5000 MIVIS (Multispectral Infrared and Visible Imaging Spectrometer) instrument. MIVIS's channels, spectral bandwidths, and locations are chosen to meet the needs of scientific research for advanced applications of remote sensing data. MIVIS can make significant contributions to solving problems in many diverse areas such as geologic exploration, land use studies, mineralogy, agricultural crop studies, energy loss analysis, pollution assessment, volcanology, forest fire management and others. The broad spectral range and the many discrete narrow channels of MIVIS provide a fine quantization of spectral information that permits accurate definition of absorption features from a variety of materials, allowing the extraction of chemical and physical information of our environment. The availability of such a hyperspectral imager, that will operate mainly in the Mediterranean area, at the present represents a unique opportunity for those who are involved in environmental studies and land-management to collect systematically large-scale and high spectral-spatial resolution data of this part of the world. Nevertheless, MIVIS deployments will touch other parts of the world, where a major interest from the international scientific community is present.

  6. Remote identification of potential polar bear maternal denning habitat in northern Alaska using airborne LiDAR

    NASA Astrophysics Data System (ADS)

    Jones, B. M.; Durner, G. M.; Stoker, J.; Shideler, R.; Perham, C.; Liston, G. E.

    2013-12-01

    Polar bear (Ursus maritimus) populations throughout the Arctic are being threatened by reductions in critical sea ice habitat. Throughout much of their range, polar bears give birth to their young in winter dens that are excavated in snowdrifts. New-born cubs, which are unable to survive exposure to Arctic winter weather, require 2-3 months of the relatively warm, stable, and undisturbed environment of the den for their growth. In the southern Beaufort Sea (BS), polar bears may den on the Alaskan Arctic Coastal Plain (ACP).The proportion of dens occurring on land has increased because of reductions in stable multi-year ice, increases in unconsolidated ice, and lengthening of the fall open-water period. Large portions of the ACP are currently being used for oil and gas activities and proposed projects will likely expand this footprint in the near future. Since petroleum exploration and development activities increase during winter there is the potential for human activities to disturb polar bears in maternal dens. Thus, maps showing the potential distribution of terrestrial denning habitat can help to mitigate negative interactions. Prior remote sensing efforts have consisted of manual interpretation of vertical aerial photography and automated classification of Interferometric Synthetic Aperture (IfSAR) derived digital terrain models (DTM) (5-m spatial resolution) focused on the identification of snowdrift forming landscape features. In this study, we assess the feasibility of airborne Light Detection and Ranging (LiDAR) data (2-m spatial resolution) for the automated classification of potential polar bear maternal denning habitat in a 1,400 km2 area on the central portion of the ACP. The study region spans the BS coast from the Prudhoe Bay oilfield in the west to near Point Thompson in the east and extends inland from 10 to 30 km. Approximately 800 km2 of the study area contains 19 known den locations, 51 field survey sites with information on bank height and

  7. Analysis of vegetation indices derived from aerial multispectral and ground hyperspectral data

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Aerial multispectral images are a good source of crop, soil, and ground coverage information. Spectral reflectance indices provide a useful tool for monitoring crop growing status. A series of aerial images were acquired by an airborne MS4100 multispectral imaging system on the cotton and soybean f...

  8. Multispectral Dual-Aperture Schmidt Objective

    NASA Technical Reports Server (NTRS)

    Minott, P. O.

    1983-01-01

    Off-axis focal planes make room for beam splitters. System includes two off-axis primary spherical reflectors, each concentric with refractive corrector at aperature. Off-axis design assures large aperture required for adequate spatial resolution. Separate images have precise registration, used for multispectral resource mapping or remote sensing.

  9. Making Carbon Emissions Remotely Sensible: Flux Observations of Carbon from an Airborne Laboratory (FOCAL), its Near-Surface Survey of Carbon Gases and Isotopologues on Alaska's North Slope

    NASA Astrophysics Data System (ADS)

    Dobosy, R.; Dumas, E. J.; Sayres, D. S.; Healy, C. E.; Munster, J. B.; Baker, B.; Anderson, J. G.

    2014-12-01

    Detailed process-oriented study of the mechanisms of conversion in the Arctic of fossil carbon to atmospheric gas is progressing, but necessarily limited to a few point locations and requiring detailed subsurface measurements inaccessible to remote sensing. Airborne measurements of concentration, transport and flux of these carbon gases at sufficiently low altitude to reflect surface variations can tie such local measurements to remotely observable features of the landscape. Carbon dioxide and water vapor have been observable for over 20 years from low-altitude small aircraft in the Arctic and elsewhere. Methane has been more difficult, requiring large powerful aircraft or limited flask samples. Recent developments in spectroscopy, however, have reduced the power and weight required to measure methane at rates suitable for eddy-covariance flux estimates. The Flux Observations of Carbon from an Airborne Laboratory (FOCAL) takes advantage of Integrated Cavity-Output Spectroscopy (ICOS) to measure CH4, CO2, and water vapor in a new airborne system. The system, moreover, measures these gases' stable isotopologues every two seconds or faster helping to separate thermogenic from biogenic emissions. Paired with the Best Airborne Turbulence (BAT) probe developed for small aircraft by NOAA's Air Resources Laboratory and a light twin-engine aircraft adapted by Aurora Flight Sciences Inc., the FOCAL measures at 6 m spacing, covering 100 km in less than 30 minutes. It flies between 10 m and 50 m above ground interspersed with profiles to the top of the boundary layer and beyond. This presentation gives an overview of the magnitude and variation in fluxes and concentrations of CH4, CO2, and H2O with space, time, and time of day in a spatially extensive survey, more than 7500 km total in 15 flights over roughly a 100 km square during the month of August 2013. An extensive data set such as this at low altitude with high-rate sampling addresses features that repeat on 1 km scale

  10. Airborne Passive Remote Sensing of the Troposphere in Nashville/Middle Tennessee Area During the 1995 Southern Oxidants Study

    NASA Technical Reports Server (NTRS)

    Rider, D. M.; Worden, H. M.; Beer, R.; Nandi, S.; Sparks, L. C.

    1998-01-01

    In July of 1995 the Airborne Emission Spectrometer was deployed to Nashville, Tennessee to participate in the 1995 Ozone Study Intensive Campaign of the Southern Oxidants Study. AES is a high resolution mid-infrared interferometer that measures the spectrum of upwelling radiation in the 650-4250 cm-1 range.

  11. Monitoring Geothermal Features in Yellowstone National Park with ATLAS Multispectral Imagery

    NASA Technical Reports Server (NTRS)

    Spruce, Joseph; Berglund, Judith

    2000-01-01

    The National Park Service (NPS) must produce an Environmental Impact Statement for each proposed development in the vicinity of known geothermal resource areas (KGRAs) in Yellowstone National Park. In addition, the NPS monitors indicator KGRAs for environmental quality and is still in the process of mapping many geothermal areas. The NPS currently maps geothermal features with field survey techniques. High resolution aerial multispectral remote sensing in the visible, NIR, SWIR, and thermal spectral regions could enable YNP geothermal features to be mapped more quickly and in greater detail In response, Yellowstone Ecosystems Studies, in partnership with NASA's Commercial Remote Sensing Program, is conducting a study on the use of Airborne Terrestrial Applications Sensor (ATLAS) multispectral data for monitoring geothermal features in the Upper Geyser Basin. ATLAS data were acquired at 2.5 meter resolution on August 17, 2000. These data were processed into land cover classifications and relative temperature maps. For sufficiently large features, the ATLAS data can map geothermal areas in terms of geyser pools and hot springs, plus multiple categories of geothermal runoff that are apparently indicative of temperature gradients and microbial matting communities. In addition, the ATLAS maps clearly identify geyserite areas. The thermal bands contributed to classification success and to the computation of relative temperature. With masking techniques, one can assess the influence of geothermal features on the Firehole River. Preliminary results appear to confirm ATLAS data utility for mapping and monitoring geothermal features. Future work will include classification refinement and additional validation.

  12. Remote distinction of a noxious weed (musk thistle: Carduus nutans) using airborne hyperspectral imagery and the support vector machine classifier

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Remote detection of invasive plant species using geospatial imagery may significantly improve monitoring, planning, and management practices by eliminating shortfalls such as observer bias and accessibility involved in ground-based surveys. The use of remote sensing for accurate mapping invasion ex...

  13. Evaluation of an airborne remote sensing platform consisting of two consumer-grade cameras for crop identification

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Remote sensing systems based on consumer-grade cameras have been increasingly used in scientific research and remote sensing applications because of their low cost and ease of use. However, the performance of consumer-grade cameras for practical applications have not been well documented in related ...

  14. A multistage database of field measurements and synoptic remotely sensed data to support model validation and testing in Earth observation

    NASA Astrophysics Data System (ADS)

    Milton, E. J.; Baret, F.; Rossello, P.; Anderson, E.; Rockall, E.

    2011-09-01

    This paper presents a novel database of ground and remotely sensed data from the United Kingdom, which is uniquely suited to scaling-up multispectral measurements from a single plot to the scale of satellite sensor observations. Multiple aircraft and satellite sensors were involved, and most of the data were acquired on a single day in June 2006, providing a synoptic view which, at its largest extent, covered most of southern England and Wales. Three airborne imaging spectrometers were involved (Specim AISA Eagle, Itres CASI-2 and -3) and three satellite sensors (UK-DMC, PROBA/CHRIS, and SPOT HRG), complemented with airborne LiDAR, multispectral survey cameras, and ground measurements (land cover, LAI, reflectance factors, and atmospheric measurements). In this paper the NCAVEO Field Campaign (NFC) database is described and an example of its use to produce a high spatial resolution leaf area index map for the validation of medium-resolution products (MODIS, VEGETATION, and MERIS) is presented.

  15. Use of land surface remotely sensed satellite and airborne data for environmental exposure assessment in cancer research

    USGS Publications Warehouse

    Maxwell, S.K.; Meliker, J.R.; Goovaerts, P.

    2010-01-01

    In recent years, geographic information systems (GIS) have increasingly been used for reconstructing individual-level exposures to environmental contaminants in epidemiological research. Remotely sensed data can be useful in creating space-time models of environmental measures. The primary advantage of using remotely sensed data is that it allows for study at the local scale (e.g., residential level) without requiring expensive, time-consuming monitoring campaigns. The purpose of our study was to identify how land surface remotely sensed data are currently being used to study the relationship between cancer and environmental contaminants, focusing primarily on agricultural chemical exposure assessment applications. We present the results of a comprehensive literature review of epidemiological research where remotely sensed imagery or land cover maps derived from remotely sensed imagery were applied. We also discuss the strengths and limitations of the most commonly used imagery data (aerial photographs and Landsat satellite imagery) and land cover maps. ?? 2010 Nature Publishing Group All rights reserved.

  16. D Land Cover Classification Based on Multispectral LIDAR Point Clouds

    NASA Astrophysics Data System (ADS)

    Zou, Xiaoliang; Zhao, Guihua; Li, Jonathan; Yang, Yuanxi; Fang, Yong

    2016-06-01

    Multispectral Lidar System can emit simultaneous laser pulses at the different wavelengths. The reflected multispectral energy is captured through a receiver of the sensor, and the return signal together with the position and orientation information of sensor is recorded. These recorded data are solved with GNSS/IMU data for further post-processing, forming high density multispectral 3D point clouds. As the first commercial multispectral airborne Lidar sensor, Optech Titan system is capable of collecting point clouds data from all three channels at 532nm visible (Green), at 1064 nm near infrared (NIR) and at 1550nm intermediate infrared (IR). It has become a new source of data for 3D land cover classification. The paper presents an Object Based Image Analysis (OBIA) approach to only use multispectral Lidar point clouds datasets for 3D land cover classification. The approach consists of three steps. Firstly, multispectral intensity images are segmented into image objects on the basis of multi-resolution segmentation integrating different scale parameters. Secondly, intensity objects are classified into nine categories by using the customized features of classification indexes and a combination the multispectral reflectance with the vertical distribution of object features. Finally, accuracy assessment is conducted via comparing random reference samples points from google imagery tiles with the classification results. The classification results show higher overall accuracy for most of the land cover types. Over 90% of overall accuracy is achieved via using multispectral Lidar point clouds for 3D land cover classification.

  17. Airborne Remote Sensing of Sea Surface Temperature Using the Ball Experimental Sea Surface Temperature (BESST) Radiometer With A Discussion of the 2013 Marginal Ice Zone Observation Processes EXperiment.

    NASA Astrophysics Data System (ADS)

    Tooth, M.; Emery, W. J.

    2014-12-01

    Airborne remote sensing has opened up new possibilities for scientists to study oceanic and atmospheric problems that are relevant to industry, environmental groups, and the scientific community as a whole. Data obtained from these platforms can provide much higher resolution imagery in comparison to satellite observations that allow for more detailed analyses of important regions. Sea surface temperature (SST) data obtained from instruments like the BESST radiometer can be used to provide more insight into issues like natural disasters and oceanographic problems of interest; such as the influence of melting sea ice on SST. During the 2013 Marginal Ice Zone Observation Processes EXperiment (MIZOPEX), BESST was flown on a Scan Eagle UAS in the Alaskan Marginal Ice Zone to acquire SST data. These observations will be discussed, along with possible future uses for the BESST radiometer.

  18. Satellite and airborne oil spill remote sensing: State of the art and application to the BP DeepWater Horizon oil spill

    USGS Publications Warehouse

    Leifer, I.; Clark, R.; Jones, C.; Holt, B.; Svejkovsky, J.; Swayze, G.

    2011-01-01

    The vast, persistent, and unconstrained oil release from the DeepWater Horizon (DWH) challenged the spill response, which required accurate quantitative oil assessment at synoptic and operational scales. Experienced observers are the mainstay of oil spill response. Key limitations are weather, scene illumination geometry, and few trained observers, leading to potential observer bias. Aiding the response was extensive passive and active satellite and airborne remote sensing, including intelligent system augmentation, reviewed herein. Oil slick appearance strongly depends on many factors like emulsion composition and scene geometry, yielding false positives and great thickness uncertainty. Oil thicknesses and the oil to water ratios for thick slicks were derived quantitatively with a new spectral library approach based on the shape and depth of spectral features related to C-H vibration bands. The approach used near infrared, imaging spectroscopy data from the AVIRIS (Airborne Visual/InfraRed Imaging Spectrometer) instrument on the NASA ER-2 stratospheric airplane. Extrapolation to the total slick used MODIS satellite visual-spectrum broadband data, which observes sunglint reflection from surface slicks; i.e., indicates the presence of oil and/or surfactant slicks. Oil slick emissivity is less than seawater's allowing MODIS thermal infrared (TIR) nighttime identification; however, water temperature variations can cause false positives. Some strong emissivity features near 6.7 and 9.7 ??m could be analyzed as for the AVIRIS short wave infrared features, but require high spectral resolution data. TIR spectral trends can allow fresh/weathered oil discrimination. Satellite Synthetic Aperture Radar (SSAR) provided synoptic data under all-sky conditions by observing oil dampening of capillary waves; however, SSAR typically cannot discriminate thick from thin oil slicks. Airborne UAVSAR's significantly greater signal-to-noise ratio and fine spatial resolution allowed

  19. Development of a low altitude airborne remote sensing system for supporting the processing of satellite remotely sensed data intended for archaeological investigations

    NASA Astrophysics Data System (ADS)

    Agapiou, Athos; Hadjimitsis, Diofantos G.; Georgopoulos, Andreas; Themistocleous, Kyriacos; Alexakis, Dimitris D.; Papadavid, George

    2012-10-01

    Earth observation techniques intended for archaeological research, such as satellite images and ground geophysical surveys are well established in the literature. In contrast, low altitude airborne systems for supporting archaeological research are still very limited. The "ICAROS" project, funded by the Cyprus Research Promotion Foundation, aims to develop an airborne system for archaeological investigations. The system will incorporate both a GER 1500 field spectroradiometer and NIR camera in a balloon system operated from the ground. The GER 1500 field spectroradiometer has the capability to record reflectance values from 400 nm up to 1050 nm (blue/green/red and NIR band). The Field of View (FOV) of the instrument is 4o while a calibrated spectralon panel will be used in order to minimize illumination errors during the data collection. Existing atmospheric conditions will be monitored using sun-photometer and meteorological station. The overall methodology of the project and the preliminary results from different cases studies in Cyprus are presented and discussed in this paper. Some practical problems are also discussed and the overall results are compared with satellite and ground measurements. Spectroradiometric measurements and NIR images will be taken from different heights from the balloon system. The results will be compared with different satellite images.

  20. The International SubMillimetre Airborne Radiometer (ISMAR) - First results from the STICCS and COSMIC campaigns

    NASA Astrophysics Data System (ADS)

    Mendrok, Jana; Eriksson, Patrick; Fox, Stuart; Brath, Manfred; Buehler, Stefan

    2016-04-01

    Multispectral millimeter- and submillimeter-wave observations bear the potential to measure properties of non-thin ice clouds like mass content and mean particle size. The next generation of European meteorological satellites, the MetOp-SG series, will carry the first satellite-borne submillimeter sounder, the Ice Cloud Imager (ICI). An airborne demonstrator, the International SubMillimetre Airborne Radiometer (ISMAR), is operated together with other remote sensing instruments and in-situ probes on the FAAM aircraft. Scientific measurements from two campaings in the North Atlantic region, STICCS and COSMIC, are available so far. Here we will introduce the ISMAR instrument, present the acquired measurements from the STICCS and COSMIC campaigns and show some first results. This will include estimation of instrument performance, first analysis of clear-sky and cloudy cases and discussion of selected features observed in the measurements (e.g. polarisation signatures).

  1. Multispectral observations of marine mammals

    NASA Astrophysics Data System (ADS)

    Schoonmaker, Jon; Dirbas, Joseph; Podobna, Yuliya; Wells, Tami; Boucher, Cynthia; Oakley, Daniel

    2008-10-01

    Multispectral visible and infrared observations of various species of whales were made in the St. Lawrence Seaway near Quebec, Canada and Papawai Point in Maui, Hawaii. The Multi-mission Adaptable Narrowband Imaging System (MANTIS) was deployed in two configurations: airborne looking down, and bluff mounted looking at low-grazing angles. An Infrared (IR) sensor was also deployed in the bluff mounted configuration. Detections of marine mammals were made with these systems of submerged mammals and surface mammals at ranges up to 8 miles. Automatic detection algorithms are being explored to detect, track and monitor the behavior of individuals and pods of whales. This effort is part of a United States Navy effort to insure that marine mammals are not injured during the testing of the US Navy's acoustic Anti-submarine Warfare (ASW) systems.

  2. Airborne remote spectrometry support to rescue personnel at Ground Zero after the World Trade Center attack on September 11, 2001

    NASA Astrophysics Data System (ADS)

    Simi, Christopher G.; Hill, Anthony B.; Kling, Henry; Zadnik, Jerome A.; Sviland, Marc D.; Williams, Mary M.; Lewis, Paul E.

    2002-11-01

    In order to assist Rescue and Recovery personnel after 11 September 2001, Night Vision and Electronic Sensors Directorate was requested to collect a variety of airborne electro-optic data of the WTC site. The immediate objective was to provide FDNY with geo-rectified high-resolution and solar reflective hyperspectral data to help map the debris-field. Later data collections included calibrated MWIR data. This thermal data provided accurate temperature profiles, which could be warped to the high-resolution data. This paper will describe the assets and software used to help provide the FDNY data products, which were incorporated into their GIS database.

  3. Remote detection of canopy water stress in coniferous forests using the NS001 Thematic Mapper Simulator and the thermal infrared multispectral scanner

    NASA Technical Reports Server (NTRS)

    Pierce, Lars L.; Running, Steven W.; Riggs, George A.

    1990-01-01

    Water stress was induced in two coniferous forest stands in West Germany by severing tree sapwood. Leaf water potential, Psi(L), measurements indicated that maximum, naturally occurring levels of water stress developed in the stressed plots while control plots exhibited natural diurnal trends. Images of each site were obtained with the Thematic Mapper Simulator (NS001) and the Thermal Infrared Multispectral Scanner (TIMS) 12 to 15 days after stress induction. NS001 bands 2 to 6, NS001 indices combining bands 4 and 6, and NS001 and TIMS thermal bands showed significant radiance differences between stressed and control plots when large differences in Psi(L) and relative water content (RWC) existed during the morning overflights at Munich. However, the NS001 and TIMS sensors could not detect the slightly smaller differences in Psi(L) and RWC during the Munich afternoon and Frankfurt overflights. The results suggest that routine detection of canopy water stress under operational conditions is difficult utilizing current sensor technology.

  4. International Symposium on Remote Sensing of Environment, 10th, University of Michigan, Ann Arbor, Mich., October 6-10, 1975, Proceedings. Volumes 1 & 2

    NASA Technical Reports Server (NTRS)

    1975-01-01

    Topics treated include the application of a Fourier transform spectrometer to infrared remote sensing, the performance optimization of a satellite-borne thematic mapper, a data handling system to be integrated with a digital airborne multispectral scanner, infrared thermography for micro- and mesometeorological measurements, satellite interrogated data collection platforms for river and flood forecasting and the automatic measurement of sea surface temperature from a GOES satellite. Solar and atmospheric effects on satellite imagery derived from aircraft reflectance measurements, methods for determining haze levels from multispectral scanner data, restoration of Landsat images by discrete two-dimensional deconvolution and the automatic classification of aircraft and satellite multispectral images using mixed integer programming are also discussed. Individual items are announced in this issue.

  5. Multispectral analysis of ocean dumped materials

    NASA Technical Reports Server (NTRS)

    Johnson, R. W.

    1977-01-01

    Experiments conducted in the Atlantic coastal zone indicated that plumes resulting from ocean dumping of acid wastes and sewage sludge have unique spectral characteristics. Remotely sensed wide area synoptic coverage provided information on these pollution features that was not readily available from other sources. Aircraft remotely sensed photographic and multispectral scanner data were interpreted by two methods. First, qualitative analyses in which pollution features were located, mapped, and identified without concurrent sea truth and, second, quantitative analyses in which concurrently collected sea truth was used to calibrate the remotely sensed data and to determine quantitative distributions of one or more parameters in a plume.

  6. Assessment of Superflux relative to fisheries research and monitoring. [airborne remote sensing of the Chesapeake bay plume and shelf regions

    NASA Technical Reports Server (NTRS)

    Thomas, J. P.

    1981-01-01

    Some of the findings of the Superflux program relative to fishery research and monitoring are reviewed. The actual and potential influences of the plume on the shelf ecosystem contiguous to the mouth of Chesapeake Bay are described and insights derived from the combined use of in situ and remotely sensed data are presented.

  7. Hyperspectral remote sensing of wild oyster reefs

    NASA Astrophysics Data System (ADS)

    Le Bris, Anthony; Rosa, Philippe; Lerouxel, Astrid; Cognie, Bruno; Gernez, Pierre; Launeau, Patrick; Robin, Marc; Barillé, Laurent

    2016-04-01

    The invasion of the wild oyster Crassostrea gigas along the western European Atlantic coast has generated changes in the structure and functioning of intertidal ecosystems. Considered as an invasive species and a trophic competitor of the cultivated conspecific oyster, it is now seen as a resource by oyster farmers following recurrent mass summer mortalities of oyster spat since 2008. Spatial distribution maps of wild oyster reefs are required by local authorities to help define management strategies. In this work, visible-near infrared (VNIR) hyperspectral and multispectral remote sensing was investigated to map two contrasted intertidal reef structures: clusters of vertical oysters building three-dimensional dense reefs in muddy areas and oysters growing horizontally creating large flat reefs in rocky areas. A spectral library, collected in situ for various conditions with an ASD spectroradiometer, was used to run Spectral Angle Mapper classifications on airborne data obtained with an HySpex sensor (160 spectral bands) and SPOT satellite HRG multispectral data (3 spectral bands). With HySpex spectral/spatial resolution, horizontal oysters in the rocky area were correctly classified but the detection was less efficient for vertical oysters in muddy areas. Poor results were obtained with the multispectral image and from spatially or spectrally degraded HySpex data, it was clear that the spectral resolution was more important than the spatial resolution. In fact, there was a systematic mud deposition on shells of vertical oyster reefs explaining the misclassification of 30% of pixels recognized as mud or microphytobenthos. Spatial distribution maps of oyster reefs were coupled with in situ biomass measurements to illustrate the interest of a remote sensing product to provide stock estimations of wild oyster reefs to be exploited by oyster producers. This work highlights the interest of developing remote sensing techniques for aquaculture applications in coastal

  8. Multispectral imaging using a single bucket detector

    PubMed Central

    Bian, Liheng; Suo, Jinli; Situ, Guohai; Li, Ziwei; Fan, Jingtao; Chen, Feng; Dai, Qionghai

    2016-01-01

    Existing multispectral imagers mostly use available array sensors to separately measure 2D data slices in a 3D spatial-spectral data cube. Thus they suffer from low photon efficiency, limited spectrum range and high cost. To address these issues, we propose to conduct multispectral imaging using a single bucket detector, to take full advantage of its high sensitivity, wide spectrum range, low cost, small size and light weight. Technically, utilizing the detector’s fast response, a scene’s 3D spatial-spectral information is multiplexed into a dense 1D measurement sequence and then demultiplexed computationally under the single pixel imaging scheme. A proof-of-concept setup is built to capture multispectral data of 64 pixels × 64 pixels × 10 wavelength bands ranging from 450 nm to 650 nm, with the acquisition time being 1 minute. The imaging scheme holds great potentials for various low light and airborne applications, and can be easily manufactured as production-volume portable multispectral imagers. PMID:27103168

  9. Multispectral imaging using a single bucket detector.

    PubMed

    Bian, Liheng; Suo, Jinli; Situ, Guohai; Li, Ziwei; Fan, Jingtao; Chen, Feng; Dai, Qionghai

    2016-01-01

    Existing multispectral imagers mostly use available array sensors to separately measure 2D data slices in a 3D spatial-spectral data cube. Thus they suffer from low photon efficiency, limited spectrum range and high cost. To address these issues, we propose to conduct multispectral imaging using a single bucket detector, to take full advantage of its high sensitivity, wide spectrum range, low cost, small size and light weight. Technically, utilizing the detector's fast response, a scene's 3D spatial-spectral information is multiplexed into a dense 1D measurement sequence and then demultiplexed computationally under the single pixel imaging scheme. A proof-of-concept setup is built to capture multispectral data of 64 pixels × 64 pixels × 10 wavelength bands ranging from 450 nm to 650 nm, with the acquisition time being 1 minute. The imaging scheme holds great potentials for various low light and airborne applications, and can be easily manufactured as production-volume portable multispectral imagers. PMID:27103168

  10. Predicting the aquatic stage sustainability of a restored backwater channel combining in-situ and airborne remotely sensed bathymetric models.

    NASA Astrophysics Data System (ADS)

    Jérôme, Lejot; Jérémie, Riquier; Hervé, Piégay

    2014-05-01

    As other large river floodplain worldwide, the floodplain of the Rhône has been deeply altered by human activities and infrastructures over the last centuries both in term of structure and functioning. An ambitious restoration plan of selected by-passed reaches has been implemented since 1999, in order to improve their ecological conditions. One of the main action aimed to increase the aquatic areas in floodplain channels (i.e. secondary channels, backwaters, …). In practice, fine and/or coarse alluvium were dredged, either locally or over the entire cut-off channel length. Sometimes the upstream or downstream alluvial plugs were also removed to reconnect the restored feature to the main channel. Such operation aims to restore forms and associated habitats of biotic communities, which are no more created or maintained by the river itself. In this context, assessing the sustainability of such restoration actions is a major issue. In this study, we focus on 1 of the 24 floodplain channels which have been restored along the Rhône River since 1999, the Malourdie channel (Chautagne reach, France). A monitoring of the geomorphologic evolution of the channel has been conducted during a decade to assess the aquatic stage sustainability of this former fully isolated channel, which has been restored as a backwater in 2004. Two main types of measures were performed: (a) water depth and fine sediment thickness were surveyed with an auger every 10 m along the channel centerline in average every year and a half allowing to establish an exponential decay model of terrestrialization rates through time; (b) three airborne campaigns (2006, 2007, 2012) by Ultra Aerial Vehicle (UAV) provided images from which bathymetry were inferred in combination with observed field measures. Coupling field and airborne models allows us to simulate different states of terrestrialization at the scale of the whole restore feature (e.g. 2020/2030/2050). Raw results indicate that terrestrialization

  11. High Resolution Airborne Digital Imagery for Precision Agriculture

    NASA Technical Reports Server (NTRS)

    Herwitz, Stanley R.

    1998-01-01

    The Environmental Research Aircraft and Sensor Technology (ERAST) program is a NASA initiative that seeks to demonstrate the application of cost-effective aircraft and sensor technology to private commercial ventures. In 1997-98, a series of flight-demonstrations and image acquisition efforts were conducted over the Hawaiian Islands using a remotely-piloted solar- powered platform (Pathfinder) and a fixed-wing piloted aircraft (Navajo) equipped with a Kodak DCS450 CIR (color infrared) digital camera. As an ERAST Science Team Member, I defined a set of flight lines over the largest coffee plantation in Hawaii: the Kauai Coffee Company's 4,000 acre Koloa Estate. Past studies have demonstrated the applications of airborne digital imaging to agricultural management. Few studies have examined the usefulness of high resolution airborne multispectral imagery with 10 cm pixel sizes. The Kodak digital camera integrated with ERAST's Airborne Real Time Imaging System (ARTIS) which generated multiband CCD images consisting of 6 x 106 pixel elements. At the designated flight altitude of 1,000 feet over the coffee plantation, pixel size was 10 cm. The study involved the analysis of imagery acquired on 5 March 1998 for the detection of anomalous reflectance values and for the definition of spectral signatures as indicators of tree vigor and treatment effectiveness (e.g., drip irrigation; fertilizer application).

  12. Airborne remote sensing of spatiotemporal change (1955-2004) in indigenous and exotic forest cover in the Taita Hills, Kenya

    NASA Astrophysics Data System (ADS)

    Pellikka, Petri K. E.; Lötjönen, Milla; Siljander, Mika; Lens, Luc

    2009-08-01

    We studied changes in area and species composition of six indigenous forest fragments in the Taita Hills, Kenya using 1955 and 1995 aerial photography with 2004 airborne digital camera mosaics. The study area is part of Eastern Arc Mountains, a global biodiversity hot spot that boasts an outstanding diversity of flora and fauna and a high level of endemism. While a total of 260 ha (50%) of indigenous tropical cloud forest was lost to agriculture and bushland between 1955 and 2004, large-scale planting of exotic pines, eucalyptus, grevillea, black wattle and cypress on barren land during the same period resulted in a balanced total forest area. In the Taita Hills, like in other Afrotropical forests, indigenous forest loss may adversely affect ecosystem services.

  13. Tropospheric Passive Remote Sensing

    NASA Technical Reports Server (NTRS)

    Keafer, L. S., Jr. (Editor)

    1982-01-01

    The long term role of airborne/spaceborne passive remote sensing systems for tropospheric air quality research and the identification of technology advances required to improve the performance of passive remote sensing systems were discussed.

  14. Assessment of Superflux relative to marine science and oceanography. [airborne remote sensing of the Chesapeake Bay plume and shelf regions

    NASA Technical Reports Server (NTRS)

    Esaias, W. E.

    1981-01-01

    A general assessment of the Superflux project is made in relation to marine science and oceanography. It is commented that the program clearly demonstrated the effectiveness of state-of-the-art technology required to study highly dynamic estuarine plumes, and the necessity of a broadly interdisciplinary, interactive remote sensing and shipboard program required to significantly advance the understanding of transport processes and impacts of estuarine outflows.

  15. Radiometric Characterization of Hyperspectral Imagers using Multispectral Sensors

    NASA Technical Reports Server (NTRS)

    McCorkel, Joel; Kurt, Thome; Leisso, Nathan; Anderson, Nikolaus; Czapla-Myers, Jeff

    2009-01-01

    The Remote Sensing Group (RSG) at the University of Arizona has a long history of using ground-based test sites for the calibration of airborne and satellite based sensors. Often, ground-truth measurements at these test sites are not always successful due to weather and funding availability. Therefore, RSG has also automated ground instrument approaches and cross-calibration methods to verify the radiometric calibration of a sensor. The goal in the cross-calibration method is to transfer the calibration of a well-known sensor to that of a different sensor, This work studies the feasibility of determining the radiometric calibration of a hyperspectral imager using multispectral a imagery. The work relies on the Moderate Resolution Imaging Spectroradiometer (M0DIS) as a reference for the hyperspectral sensor Hyperion. Test sites used for comparisons are Railroad Valley in Nevada and a portion of the Libyan Desert in North Africa. Hyperion bands are compared to MODIS by band averaging Hyperion's high spectral resolution data with the relative spectral response of M0DlS. The results compare cross-calibration scenarios that differ in image acquisition coincidence, test site used for the calibration, and reference sensor. Cross-calibration results are presented that show agreement between the use of coincident and non-coincident image pairs within 2% in most brands as well as similar agreement between results that employ the different MODIS sensors as a reference.

  16. Radiometric characterization of hyperspectral imagers using multispectral sensors

    NASA Astrophysics Data System (ADS)

    McCorkel, Joel; Thome, Kurt; Leisso, Nathan; Anderson, Nikolaus; Czapla-Myers, Jeff

    2009-08-01

    The Remote Sensing Group (RSG) at the University of Arizona has a long history of using ground-based test sites for the calibration of airborne and satellite based sensors. Often, ground-truth measurements at these tests sites are not always successful due to weather and funding availability. Therefore, RSG has also employed automated ground instrument approaches and cross-calibration methods to verify the radiometric calibration of a sensor. The goal in the cross-calibration method is to transfer the calibration of a well-known sensor to that of a different sensor. This work studies the feasibility of determining the radiometric calibration of a hyperspectral imager using multispectral imagery. The work relies on the Moderate Resolution Imaging Spectroradiometer (MODIS) as a reference for the hyperspectral sensor Hyperion. Test sites used for comparisons are Railroad Valley in Nevada and a portion of the Libyan Desert in North Africa. Hyperion bands are compared to MODIS by band averaging Hyperion's high spectral resolution data with the relative spectral response of MODIS. The results compare cross-calibration scenarios that differ in image acquisition coincidence, test site used for the calibration, and reference sensor. Cross-calibration results are presented that show agreement between the use of coincident and non-coincident image pairs within 2% in most bands as well as similar agreement between results that employ the different MODIS sensors as a reference.

  17. Investigation of Arctic mixed-phase clouds by combining airborne remote sensing and in situ observations during VERDI, RACEPAC and ACLOUD

    NASA Astrophysics Data System (ADS)

    Ehrlich, André; Bierwirth, Eike; Borrmann, Stephan; Crewell, Susanne; Herber, Andreas; Hoor, Peter; Jourdan, Olivier; Krämer, Martina; Lüpkes, Christof; Mertes, Stephan; Neuber, Roland; Petzold, Andreas; Schnaiter, Martin; Schneider, Johannes; Weigel, Ralf; Weinzierl, Bernadett; Wendisch, Manfred

    2016-04-01

    To improve our understanding of Arctic mixed-phase clouds a series of airborne research campaigns has been initiated by a collaboration of German research institutes. Clouds in areas dominated by a close sea-ice cover were observed during the research campaign Vertical distribution of ice in Arctic mixed-phase clouds (VERDI, April/May 2012) and the Radiation-Aerosol-Cloud Experiment in the Arctic Circle (RACEPAC, April/May 2014) which both were based in Inuvik, Canada. The aircraft (Polar 5 & 6, Basler BT-67) operated by the Alfred Wegener Institute for Polar and Marine Research, Germany did cover a wide area above the Canadian Beaufort with in total 149 flight hours (62h during VERDI, 87h during RACEPAC). For May/June 2017 a third campaign ACLOUD (Arctic Clouds - Characterization of Ice, aerosol Particles and Energy fluxes) with base in Svalbard is planned within the Transregional Collaborative Research Centre TR 172 ArctiC Amplification: Climate Relevant Atmospheric and SurfaCe Processes, and Feedback Mechanisms (AC)3 to investigate Arctic clouds in the transition zone between open ocean and sea ice. The aim of all campaigns is to combine remote sensing and in-situ cloud, aerosol and trace gas measurements to investigate interactions between radiation, cloud and aerosol particles. While during VERDI remote sensing and in-situ measurements were performed by one aircraft subsequently, for RACEPAC and ACLOUD two identical aircraft are coordinated at different altitudes to horizontally collocate both remote sensing and in-situ measurements. The campaign showed that in this way radiative and microphysical processes in the clouds can by studied more reliably and remote sensing methods can be validated efficiently. Here we will illustrate the scientific strategy of the projects including the progress in instrumentation. Differences in the general synoptic and sea ice situation and related changes in cloud properties at the different locations and seasons will be

  18. Genetic refinement of cloud-masking algorithms for the multi-spectral thermal imager (MTI)

    SciTech Connect

    Hirsch, K. L.; Davis, A. B.; Harvey, N. R.; Rohde, C. A.; Brumby, Steven P.

    2001-01-01

    The Multi-spectral Thermal Imager (MTI) is a high-performance remote-sensing satellite designed, owned and operated by the U.S. Department of Energy, with a dual mission in environmental studies and in nonproliferation. It has enhanced spatial and radiometric resolutions and state-of-the-art calibration capabilities. This instrumental development puts a new burden on retrieval algorithm developers to pass this accuracy on to the inferred geophysical parameters. In particular, the atmospheric correction scheme assumes the intervening atmosphere will be modeled as a plane-parallel horizontally-homogeneous medium. A single dense-enough cloud in view of the ground target can easily offset reality from the calculations, hence the need for a reliable cloud-masking algorithm. Pixel-scale cloud detection relies on the simple facts that clouds are generally whiter, brighter, and colder than the ground below; spatially, dense clouds are generally large on some scale. This is a good basis for searching multispectral datacubes for cloud signatures. However, the resulting cloud mask can be very sensitive to the choice of thresholds in whiteness, brightness, temperature, and connectivity. We have used a genetic algorithm trained on (MODIS Airborne Simulator-based) simulated MTI data to design a cloud-mask. Its performance is compared quantitatively to hand-drawn training data and to the EOS/Terra MODIS cloud mask.

  19. The Relationship Between Fossil and Dairy Greenhouse Gas Emissions and Complex Urban Land-Use Patterns by In Situ and Remote Sensing Data from Surface Mobile, Airborne, and Satellite Instruments

    NASA Astrophysics Data System (ADS)

    Leifer, I.; Melton, C.; Tratt, D. M.; Kuze, A.; Buckland, K. N.; Butz, A.; Deguchi, A.; Eastwood, M. L.; Fischer, M. L.; Frash, J.; Fladeland, M. M.; Gore, W.; Iraci, L. T.; Johnson, P. D.; Kataoka, F.; Kolyer, R.; Leen, J. B.; Quattrochi, D. A.; Shiomi, K.; Suto, H.; Tanaka, T.; Thompson, D. R.; Yates, E. L.; Van Damme, M.; Yokota, T.

    2015-12-01

    The GOSAT-COMEX-IASI Experiment (Greenhouse gases Observing SATellite-CO2and Methane EXperiment) demonstrated a novel approach to airborne-surface mobile in situ data fusion for interpretation and validation of satellite and airborne remote sensing data of greenhouse gases and direct calculation of flux. Key data were collected for the Chino Dairy in the Los Angeles Basin, California and for the Kern River Oil Fields adjacent to Bakersfield, California. In situ surface and remote sensing greenhouse gas and ammonia observations were compared with IASI and GOSAT retreivals, while hyperspectral imaging data from the AVIRIS, AVIRIS NG, and Mako airborne sensors were analyzed to relate emissions and land use. Figure - platforms participating in the experiment. TANSO-FTS aboard the Ibuki satellite (GOSAT) provided targeted pixels to measure column greenhouse gases. AMOG is the AutoMObile Gas Surveyor which supports a suite of meteorology and in situ trace gas sensors for mobile high speed measurement. AVIRIS, the Airborne Visual InfraRed Imaging Spectrometer aboard the NASA ER-2 airplane collected hyperspectral imaging data at 20 m resolution from 60,000 ft. Mako is a thermal infrared imaging spectrometer that was flown on the Twin Otter International. AJAX is a fighter jet outfitted for science sporting meteorology and greenhouse gas sensors. RAMVan is an upward looking FTIR for measuring column methane and ammonia and other trace gases.

  20. Comparison of Reflected Solar Radiance Using Aqua Modis and Airborne Remote Sensing (case : Deep Convective Clouds and Cirrus Clouds)

    NASA Astrophysics Data System (ADS)

    Krisna, T. C.; Ehrlich, A.; Werner, F.; Wendisch, M.

    2015-12-01

    Deep Convective Clouds (DCCs) have key role in the tropical region. Despite they only have small spatial coverage, but they account most of the total precipitation in these region which often make flooding. There are such of aviation accidents caused by strong vertical wind, hailing, icing and lightning inside the clouds. Pollutions caused by biomass burning and land degradation can change the aerosol properties as well as cloud properties, therefore will influence the radiation and formation of the DCCs. Those are the major reasons that better understanding of DCCs formation and life cycle are necessary. Between Sept. 01 - Oct. 14, ACRIDICON (Aerosol, Cloud, Precipitation, and Radiation Interactions and Dynamics of Concevtive Clouds Systems) campaign was conducted over Amazonia. It is suitable area to be the site-study due to has strong contrast environtment (pristine and polluted), regular convection activities and stable meteorological condition. In this study we focus on the 2 satellite validation missions designed to fly collocated but in different altitude with A-TRAIN constellation. In order to study DCCs-solar radiation interaction, we use SMART (Spectral Modular Airborne Radiation Measurements System) installed on HALO (High Altitude and Long-Range Research Aircraft) which measures spectral Irradiance (F) and Radiance (I) at the wavelength between 300-2200 nm corresponding to satellite. Due to the limitation in spatial and temporal, airborne measurements only give snapshots of atmosphere condition and DCCs formation, therefore we use multi-satellite data as DCCs have high vertical and horizontal distance, long temporal development and complex form. The comparison of AQUA MODIS and SMART Radiance at 645 nm (non-absorbing) in the clear-sky condition gives strong agreement, but in the multilayer-cloud condition gives worse and results in high underestimation (-86%) in SMART data especially at lower altitude. The bias is caused by interference from clouds

  1. Mapping playa evaporite minerals and associated sediments in Death Valley, California, with multispectral thermal infrared images

    USGS Publications Warehouse

    Crowley, J.K.; Hook, S.J.

    1996-01-01

    Efflorescent salt crusts and associated sediments in Death Valley, California, were studied with remote-sensing data acquired by the NASA thermal infrared multispectral scanner (TIMS). Nine spectral classes that represent a variety of surface materials were distinguished, including several classes that reflect important aspects of the playa groundwater chemistry and hydrology. Evaporite crusts containing abundant thenardite (sodium sulfate) were mapped along the northern and eastern margins of the Cottonball Basin, areas where the inflow waters are rich in sodium. Gypsum (calcium sulfate) crusts were more common in the Badwater Basin, particularly near springs associated with calcic groundwaters along the western basin margin. Evaporite-rich crusts generally marked areas where groundwater is periodically near the surface and thus able to replenish the crusts though capillary evaporation. Detrital silicate minerals were prevalent in other parts of the salt pan where shallow groundwater does not affect the surface composition. The surface features in Death Valley change in response to climatic variations on several different timescales. For example, salt crusts on low-lying mudflats form and redissolve during seasonal-to-interannual cycles of wetting and desiccation. In contrast, recent flooding and erosion of rough-salt surfaces in Death Valley probably reflect increased regional precipitation spanning several decades. Remote-sensing observations of playas can provide a means for monitoring changes in evaporite facies and for better understanding the associated climatic processes. At present, such studies are limited by the availability of suitable airborne scanner data. However, with the launch of the Earth Observing System (EOS) AM-1 Platform in 1998, multispectral visible/near-infrared and thermal infrared remote-sensing data will become globally available. Copyright 1996 by the American Geophysical Union.

  2. Remote sensing of multi-level wind fields with high-energy airborne scanning coherent Doppler lidar.

    PubMed

    Rothermel, J; Olivier, L; Banta, R; Hardesty, R M; Howell, J; Cutten, D; Johnson, S; Menzies, R; Tratt, D M

    1998-01-19

    The atmospheric lidar remote sensing groups of NOAA Environmental Technology Laboratory, NASA Marshall Space Flight Center, and Jet Propulsion Laboratory have developed and flown a scanning, 1 Joule per pulse, CO2 coherent Doppler lidar capable of mapping a three-dimensional volume of atmospheric winds and aerosol backscatter in the planetary boundary layer, free troposphere, and lower stratosphere. Applications include the study of severe and non-severe atmospheric flows, intercomparisons with other sensors, and the simulation of prospective satellite Doppler lidar wind profilers. Examples of wind measurements are given for the marine boundary layer and near the coastline of the western United States. PMID:19377577

  3. Remote Sensing of Multi-Level Wind Fields with High-Energy Airborne Scanning Coherent Doppler Lidar

    NASA Technical Reports Server (NTRS)

    Rothermel, Jeffry; Olivier, Lisa D.; Banta, Robert M.; Hardesty, R. Michael; Howell, James N.; Cutten, Dean R.; Johnson, Steven C.; Menzies, Robert T.; Tratt, David M.

    1997-01-01

    The atmospheric lidar remote sensing groups of NOAA Environmental Technology Laboratory, NASA Marshall Space Flight Center, and Jet Propulsion Laboratory have developed and flown a scanning, 1 Joule per pulse, CO2 coherent Doppler lidar capable of mapping a three-dimensional volume of atmospheric winds and aerosol backscatter in the troposphere and lower stratosphere. Applications include the study of severe and non-severe atmospheric flows, intercomparisons with other sensors, and the simulation of prospective satellite Doppler lidar wind profilers. Examples of wind measurements are given for the marine boundary layer and near the coastline of the western United States.

  4. Detection of a buried horizon with a high thermal diffusivity using thermal remote sensing

    NASA Technical Reports Server (NTRS)

    Nash, David B.

    1988-01-01

    A field investigation using thermal remote sensing was performed to test the feasibility of detecting the surface topography of granite bedrock beneath a thin cover of alluvium. Imagery of a region of the Mojave Desert were taken with an airborne multispectral scanner with thermal spectral bandwidths of 10.4 and 12.5 microns an instantaneous field of view of 2.5 mrad. It is suggested that a buried high thermal diffusivity horizon measurably lowers the surface temperature of the overlying lower diffusivity material during the peak of the annual heating cycle.

  5. The Airborne Multiangle SpectroPolarimetric Imager (AirMSPI): a new tool for aerosol and cloud remote sensing

    NASA Astrophysics Data System (ADS)

    Diner, D. J.; Xu, F.; Garay, M. J.; Martonchik, J. V.; Rheingans, B. E.; Geier, S.; Davis, A.; Hancock, B. R.; Jovanovic, V. M.; Bull, M. A.; Capraro, K.; Chipman, R. A.; McClain, S. C.

    2013-08-01

    The Airborne Multiangle SpectroPolarimetric Imager (AirMSPI) is an eight-band (355, 380, 445, 470, 555, 660, 865, 935 nm) pushbroom camera, measuring polarization in the 470, 660, and 865 nm bands, mounted on a gimbal to acquire multiangular observations over a ±67° along-track range. The instrument has been flying aboard the NASA ER-2 high altitude aircraft since October 2010. AirMSPI employs a photoelastic modulator-based polarimetric imaging technique to enable accurate measurements of the degree and angle of linear polarization in addition to spectral intensity. A description of the AirMSPI instrument and ground data processing approach is presented. Example images of clear, hazy, and cloudy scenes over the Pacific Ocean and California land targets obtained during flights between 2010 and 2012 are shown, and quantitative interpretations of the data using vector radiative transfer theory and scene models are provided to highlight the instrument's capabilities for determining aerosol and cloud microphysical properties and cloud 3-D spatial distributions. Sensitivity to parameters such as aerosol particle size distribution, ocean surface wind speed and direction, cloud-top and cloud-base height, and cloud droplet size is discussed. AirMSPI represents a major step toward realization of the type of imaging polarimeter envisioned to fly on NASA's Aerosol-Cloud-Ecosystem (ACE) mission in the next decade.

  6. The Airborne Multiangle SpectroPolarimetric Imager (AirMSPI): a new tool for aerosol and cloud remote sensing

    NASA Astrophysics Data System (ADS)

    Diner, D. J.; Xu, F.; Garay, M. J.; Martonchik, J. V.; Rheingans, B. E.; Geier, S.; Davis, A.; Hancock, B. R.; Jovanovic, V. M.; Bull, M. A.; Capraro, K.; Chipman, R. A.; McClain, S. C.

    2013-02-01

    The Airborne Multiangle SpectroPolarimetric Imager (AirMSPI) is an eight-band (355, 380, 445, 470, 555, 660, 865, 935 nm) pushbroom camera, measuring polarization in the 470, 660, and 865 nm bands, mounted on a gimbal to acquire multiangular observations over a ± 67° along-track range. The instrument has been flying aboard the NASA ER-2 high altitude aircraft since October 2010. AirMSPI employs a photoelastic modulator-based polarimetric imaging technique to enable accurate measurements of the degree and angle of linear polarization in addition to spectral intensity. A description of the AirMSPI instrument and ground data processing approach is presented. Example images of clear, hazy, and cloudy scenes over the Pacific Ocean and California land targets obtained during flights between 2010 and 2012 are shown, and quantitative interpretations of the data using vector radiative transfer theory and scene models are provided to highlight the instrument's capabilities for determining aerosol and cloud microphysical properties and cloud 3-D spatial distributions. Sensitivity to parameters such as aerosol particle size distribution, ocean surface wind speed and direction, cloud-top and cloud-base height, and cloud droplet size is discussed. AirMSPI represents a major step toward realization of the type of imaging polarimeter envisioned to fly on NASA's Aerosol-Cloud-Ecosystem (ACE) mission in the next decade.

  7. Modeling of mean radiant temperature based on comparison of airborne remote sensing data with surface measured data

    NASA Astrophysics Data System (ADS)

    Chen, Yu-Cheng; Chen, Chih-Yu; Matzarakis, Andreas; Liu, Jin-King; Lin, Tzu-Ping

    2016-06-01

    Assessment of outdoor thermal comfort is becoming increasingly important due to the urban heat island effect, which strongly affects the urban thermal environment. The mean radiant temperature (Tmrt) quantifies the effect of the radiation environment on humans, but it can only be estimated based on influencing parameters and factors. Knowledge of Tmrt is important for quantifying the heat load on human beings, especially during heat waves. This study estimates Tmrt using several methods, which are based on climatic data from a traditional weather station, microscale ground surface measurements, land surface temperature (LST) and light detection and ranging (LIDAR) data measured using airborne devices. Analytical results reveal that the best means of estimating Tmrt combines information about LST and surface elevation information with meteorological data from the closest weather station. The application in this method can eliminate the inconvenience of executing a wide range ground surface measurement, the insufficient resolution of satellite data and the incomplete data of current urban built environments. This method can be used to map a whole city to identify hot spots, and can be contributed to understanding human biometeorological conditions quickly and accurately.

  8. Remote sensing of coastal processes and resources

    NASA Technical Reports Server (NTRS)

    Klemas, V.

    1981-01-01

    The use of remote sensors and multispectral analysis techniques in solving environmental and resource management problems in the coastal zone is illustrated. The specific applications discussed include the analysis of coastal vegetation and productivity, remote sensing of estuarine fronts and their effects on oil dispersion, drift and dispersion of ocean-dumped wastes, and multispectral analysis of water pollutants and suspended sediment concentration.

  9. Extending airborne electromagnetic surveys for regional active layer and permafrost mapping with remote sensing and ancillary data, Yukon Flats ecoregion, central Alaska

    USGS Publications Warehouse

    Pastick, Neal J.; Jorgenson, M. Torre; Wylie, Bruce K.; Minsley, Burke J.; Ji, Lei; Walvoord, Michelle A.; Smith, Bruce D.; Abraham, Jared D.; Rose, Joshua R.

    2013-01-01

    Machine-learning regression tree models were used to extrapolate airborne electromagnetic resistivity data collected along flight lines in the Yukon Flats Ecoregion, central Alaska, for regional mapping of permafrost. This method of extrapolation (r = 0.86) used subsurface resistivity, Landsat Thematic Mapper (TM) at-sensor reflectance, thermal, TM-derived spectral indices, digital elevation models and other relevant spatial data to estimate near-surface (0–2.6-m depth) resistivity at 30-m resolution. A piecewise regression model (r = 0.82) and a presence/absence decision tree classification (accuracy of 87%) were used to estimate active-layer thickness (ALT) (< 101 cm) and the probability of near-surface (up to 123-cm depth) permafrost occurrence from field data, modelled near-surface (0–2.6 m) resistivity, and other relevant remote sensing and map data. At site scale, the predicted ALTs were similar to those previously observed for different vegetation types. At the landscape scale, the predicted ALTs tended to be thinner on higher-elevation loess deposits than on low-lying alluvial and sand sheet deposits of the Yukon Flats. The ALT and permafrost maps provide a baseline for future permafrost monitoring, serve as inputs for modelling hydrological and carbon cycles at local to regional scales, and offer insight into the ALT response to fire and thaw processes.

  10. [Researches of soil normalized difference water index (NDWI) of Yongding River based on multispectral remote sensing technology combined with genetic algorithm].

    PubMed

    Mao, Hai-ying; Feng, Zhong-ke; Gong, Yin-xi; Yu, Jing-xin

    2014-06-01

    Basin soil type, moisture content and vegetation cover index are important factors affecting the basin water of Yongding River, using traditional sampling method to investigate soil moisture and the watershed soil type not only consuming a lot of manpower and material resources but also causing experimental error because of the instrument and other objective factors. This article selecting the Yongding River Basin-Beijing section as the study area, using total station instruments to survey field sampling and determination 34 plots, combined with 6 TM image data from 1978 to 2009 to extract soil information and the relationship between region's soil type, soil moisture and remote sensing factors. Using genetic algorithms normalization to select key factors which influenced NDWI, which is based on the green band and near-infrared bands normalized ratio index, usually used to extract water information in the image. In order to accurate screening and factors related to soil moisture, using genetic algorithms preferred characteristics, accelerate the convergence by controlling the number of iterations to filter key factor. Using multiple regression method to establish NDWI inversion model, which analysis the accuracy of model is 0.987, also use the species outside edges tree to meet accuracy test, which arrived that soil available nitrogen, phosphorus and potassium content and longitude correlation is not obvious, but a positive correlation with latitude and soil, inner precision researched 87.6% when the number of iterations to achieve optimal model calculation Maxgen. Models between NDWI and vegetation cover, topography, climate ect, through remote sensing and field survey methods could calculate the NDWI values compared with the traditional values, arrived the average relative error E is -0.021%, suits accord P reached 87.54%. The establishment of this model will be provide better practical and theoretical basis to the research and analysis of the watershed soil

  11. Comparison of Hyperspectral and Multispectral Satellites for Discriminating Land Cover in Northern California

    NASA Astrophysics Data System (ADS)

    Clark, M. L.; Kilham, N. E.

    2015-12-01

    Land-cover maps are important science products needed for natural resource and ecosystem service management, biodiversity conservation planning, and assessing human-induced and natural drivers of land change. Most land-cover maps at regional to global scales are produced with remote sensing techniques applied to multispectral satellite imagery with 30-500 m pixel sizes (e.g., Landsat, MODIS). Hyperspectral, or imaging spectrometer, imagery measuring the visible to shortwave infrared regions (VSWIR) of the spectrum have shown impressive capacity to map plant species and coarser land-cover associations, yet techniques have not been widely tested at regional and greater spatial scales. The Hyperspectral Infrared Imager (HyspIRI) mission is a VSWIR hyperspectral and thermal satellite being considered for development by NASA. The goal of this study was to assess multi-temporal, HyspIRI-like satellite imagery for improved land cover mapping relative to multispectral satellites. We mapped FAO Land Cover Classification System (LCCS) classes over 22,500 km2 in the San Francisco Bay Area, California using 30-m HyspIRI, Landsat 8 and Sentinel-2 imagery simulated from data acquired by NASA's AVIRIS airborne sensor. Random Forests (RF) and Multiple-Endmember Spectral Mixture Analysis (MESMA) classifiers were applied to the simulated images and accuracies were compared to those from real Landsat 8 images. The RF classifier was superior to MESMA, and multi-temporal data yielded higher accuracy than summer-only data. With RF, hyperspectral data had overall accuracy of 72.2% and 85.1% with full 20-class and reduced 12-class schemes, respectively. Multispectral imagery had lower accuracy. For example, simulated and real Landsat data had 7.5% and 4.6% lower accuracy than HyspIRI data with 12 classes, respectively. In summary, our results indicate increased mapping accuracy using HyspIRI multi-temporal imagery, particularly in discriminating different natural vegetation types, such as

  12. Analysis of airborne particulate matter (PM2.5) over Hong Kong using remote sensing and GIS.

    PubMed

    Shi, Wenzhong; Wong, Man Sing; Wang, Jingzhi; Zhao, Yuanling

    2012-01-01

    Airborne fine particulates (PM(2.5); particulate matter with diameter less than 2.5 μm) are receiving increasing attention for their potential toxicities and roles in visibility and health. In this study, we interpreted the behavior of PM(2.5) and its correlation with meteorological parameters in Hong Kong, during 2007-2008. Significant diurnal variations of PM(2.5) concentrations were observed and showed a distinctive bimodal pattern with two marked peaks during the morning and evening rush hour times, due to dense traffic. The study observed higher PM(2.5) concentrations in winter when the northerly and northeasterly winds bring pollutants from the Chinese mainland, whereas southerly monsoon winds from the sea bring fresh air to the city in summer. In addition, higher concentrations of PM(2.5) were observed in rush hours on weekdays compared to weekends, suggesting the influence of anthropogenic activities on fine particulate levels, e.g., traffic-related local PM(2.5) emissions. To understand the spatial pattern of PM(2.5) concentrations in the context of the built-up environment of Hong Kong, we utilized MODerate Resolution Imaging Spectroradiometer (MODIS) Aerosol Optical Thickness (AOT) 500 m data and visibility data to derive aerosol extinction profile, then converted to aerosol and PM(2.5) vertical profiles. A Geographic Information Systems (GIS) prototype was developed to integrate atmospheric PM(2.5) vertical profiles with 3D GIS data. An example of the query function in GIS prototype is given. The resulting 3D database of PM(2.5) concentrations provides crucial information to air quality regulators and decision makers to comply with air quality standards and in devising control strategies. PMID:22969323

  13. Analysis of Airborne Particulate Matter (PM2.5) over Hong Kong Using Remote Sensing and GIS

    PubMed Central

    Shi, Wenzhong; Wong, Man Sing; Wang, Jingzhi; Zhao, Yuanling

    2012-01-01

    Airborne fine particulates (PM2.5; particulate matter with diameter less than 2.5 μm) are receiving increasing attention for their potential toxicities and roles in visibility and health. In this study, we interpreted the behavior of PM2.5 and its correlation with meteorological parameters in Hong Kong, during 2007–2008. Significant diurnal variations of PM2.5 concentrations were observed and showed a distinctive bimodal pattern with two marked peaks during the morning and evening rush hour times, due to dense traffic. The study observed higher PM2.5 concentrations in winter when the northerly and northeasterly winds bring pollutants from the Chinese mainland, whereas southerly monsoon winds from the sea bring fresh air to the city in summer. In addition, higher concentrations of PM2.5 were observed in rush hours on weekdays compared to weekends, suggesting the influence of anthropogenic activities on fine particulate levels, e.g., traffic-related local PM2.5 emissions. To understand the spatial pattern of PM2.5 concentrations in the context of the built-up environment of Hong Kong, we utilized MODerate Resolution Imaging Spectroradiometer (MODIS) Aerosol Optical Thickness (AOT) 500 m data and visibility data to derive aerosol extinction profile, then converted to aerosol and PM2.5 vertical profiles. A Geographic Information Systems (GIS) prototype was developed to integrate atmospheric PM2.5 vertical profiles with 3D GIS data. An example of the query function in GIS prototype is given. The resulting 3D database of PM2.5 concentrations provides crucial information to air quality regulators and decision makers to comply with air quality standards and in devising control strategies. PMID:22969323

  14. Active remote sensing of snow using NMM3D/DMRT and comparison with CLPX II airborne data

    USGS Publications Warehouse

    Xu, X.; Liang, D.; Tsang, L.; Andreadis, K.M.; Josberger, E.G.; Lettenmaier, D.P.; Cline, D.W.; Yueh, S.H.

    2010-01-01

    We applied the Numerical Maxwell Model of three-dimensional simulations (NMM3D) in the Dense Media Radiative Theory (DMRT) to calculate backscattering coefficients. The particles' positions are computer-generated and the subsequent Foldy-Lax equations solved numerically. The phase matrix in NMM3D has significant cross-polarization, particularly when the particles are densely packed. The NMM3D model is combined with DMRT in calculating the microwave scattering by dry snow. The NMM3D/DMRT equations are solved by an iterative solution up to the second order in the case of small to moderate optical thickness. The numerical results of NMM3D/DMRT are illustrated and compared with QCA/DMRT. The QCA/DMRT and NMM3D/DMRT results are also applied to compare with data from two specific datasets from the second Cold Land Processes Experiment (CLPX II) in Alaska and Colorado. The data are obtained at the Ku-band (13.95 GHz) observations using airborne imaging polarimetric scatterometer (POLSCAT). It is shown that the model predictions agree with the field measurements for both co-polarization and cross-polarization. For the Alaska region, the average snow depth and snow density are used as the inputs for DMRT. The grain size, selected from within the range of the ground measurements, is used as a best-fit parameter within the range. For the Colorado region, we use the Variable Infiltration Capacity Model (VIC) to obtain the input snow profiles for NMM3D/DMRT. ?? 2010 IEEE.

  15. Characterization of post-fire surface cover, soils, and burn severity at the Cerro Grande Fire, New Mexico, using hyperspectral and multispectral remote sensing

    USGS Publications Warehouse

    Kokaly, R.F.; Rockwell, B.W.; Haire, S.L.; King, T.V.V.

    2007-01-01

    Forest fires leave behind a changed ecosystem with a patchwork of surface cover that includes ash, charred organic matter, soils and soil minerals, and dead, damaged, and living vegetation. The distributions of these materials affect post-fire processes of erosion, nutrient cycling, and vegetation regrowth. We analyzed high spatial resolution (2.4??m pixel size) Airborne Visible and Infrared Imaging Spectrometer (AVIRIS) data collected over the Cerro Grande fire, to map post-fire surface cover into 10 classes, including ash, soil minerals, scorched conifer trees, and green vegetation. The Cerro Grande fire occurred near Los Alamos, New Mexico, in May 2000. The AVIRIS data were collected September 3, 2000. The surface cover map revealed complex patterns of ash, iron oxide minerals, and clay minerals in areas of complete combustion. Scorched conifer trees, which retained dry needles heated by the fire but not fully combusted by the flames, were found to cover much of the post-fire landscape. These scorched trees were found in narrow zones at the edges of completely burned areas. A surface cover map was also made using Landsat Enhanced Thematic Mapper plus (ETM+) data, collected September 5, 2000, and a maximum likelihood, supervised classification. When compared to AVIRIS, the Landsat classification grossly overestimated cover by dry conifer and ash classes and severely underestimated soil and green vegetation cover. In a comparison of AVIRIS surface cover to the Burned Area Emergency Rehabilitation (BAER) map of burn severity, the BAER high burn severity areas did not capture the variable patterns of post-fire surface cover by ash, soil, and scorched conifer trees seen in the AVIRIS map. The BAER map, derived from air photos, also did not capture the distribution of scorched trees that were observed in the AVIRIS map. Similarly, the moderate severity class of Landsat-derived burn severity maps generated from the differenced Normalized Burn Ratio (dNBR) calculation

  16. Gyrocopter-Based Remote Sensing Platform

    NASA Astrophysics Data System (ADS)

    Weber, I.; Jenal, A.; Kneer, C.; Bongartz, J.

    2015-04-01

    In this paper the development of a lightweight and highly modularized airborne sensor platform for remote sensing applications utilizing a gyrocopter as a carrier platform is described. The current sensor configuration consists of a high resolution DSLR camera for VIS-RGB recordings. As a second sensor modality, a snapshot hyperspectral camera was integrated in the aircraft. Moreover a custom-developed thermal imaging system composed of a VIS-PAN camera and a LWIR-camera is used for aerial recordings in the thermal infrared range. Furthermore another custom-developed highly flexible imaging system for high resolution multispectral image acquisition with up to six spectral bands in the VIS-NIR range is presented. The performance of the overall system was tested during several flights with all sensor modalities and the precalculated demands with respect to spatial resolution and reliability were validated. The collected data sets were georeferenced, georectified, orthorectified and then stitched to mosaics.

  17. Multispectral remote sensing of the Gosses Bluff impact crater, central Australia (N.T.) by using Landsat-TM and ERS-1 data

    NASA Astrophysics Data System (ADS)

    Prinz, Torsten

    Remote sensing techniques offer a unique chance to analyse and to map planetary impact craters in a relatively short time and at low cost. In the past, studies were mainly restricted to the search for possible impact sites (e.g. Earth) or for age determinations (crater statistics). On the basis of Landsat-TM 5 and ERS-1 data the lithological and structural characteristics of the complex Gosses Bluff impact crater (Australia) has been analysed in order to obtain reasonable lithological classification approaches. The fundamental statistical selection rule for pure colour composites of original TM-data was the calculation of the optimum index factor (OIF), or for hybrid colour composites (e.g. a combination of a original TM-band with a principal component and a ratio) using the widest statistical variance for each dataset. Additional spectral measurements were carried out for each representative rock unit of the crater specific zones in order to estimate the quality of supervised maximum-likelihood computer classifications for geological mapping. Complementary ERS-1 altimetric data were utilized to study the resulting crater morphology as an expression of the displacement effects and some structural features of the target caused by the cratering process (e.g. diameter, fracture pattern, ejecta displacement, etc.).

  18. High resolution mapping of the tropospheric NO2 distribution in three Belgian cities based on airborne APEX remote sensing

    NASA Astrophysics Data System (ADS)

    Tack, Frederik; Merlaud, Alexis; Fayt, Caroline; Danckaert, Thomas; Iordache, Daniel; Meuleman, Koen; Deutsch, Felix; Adriaenssens, Sandy; Fierens, Frans; Van Roozendael, Michel

    2015-04-01

    An approach is presented to retrieve tropospheric nitrogen dioxide (NO2) vertical column densities (VCDs) and to map the NO2 two dimensional distribution at high resolution, based on Airborne Prism EXperiment (APEX) observations. APEX, developed by a Swiss-Belgian consortium on behalf of ESA (European Space Agency), is a pushbroom hyperspectral imager with a high spatial (approximately 3 m at 5000 m ASL), spectral (413 to 2421 nm in 533 narrow, contiguous spectral bands) and radiometric (14-bit) resolution. VCDs are derived, following a similar approach as described in the pioneering work of Popp et al. (2012), based on (1) spectral calibration and spatial binning of the observed radiance spectra in order to improve the spectral resolution and signal-to-noise ratio, (2) Differential Optical Absorption Spectroscopy (DOAS) analysis of the pre-processed spectra in the visible wavelength region, with a reference spectrum containing low NO2 absorption, in order to quantify the abundance of NO2 along the light path, based on its molecular absorption structures and (3) radiative transfer modeling for air mass factor calculation in order to convert slant to vertical columns. This study will be done in the framework of the BUMBA (Belgian Urban NO2 Monitoring Based on APEX hyperspectral data) project. Dedicated flights with APEX mounted in a Dornier DO-228 airplane, operated by Deutsches Zentrum für Luft- und Raumfahrt (DLR), are planned to be performed in Spring 2015 above the three largest and most heavily polluted Belgian cities, i.e. Brussels, Antwerp and Liège. The retrieved VCDs will be validated by comparison with correlative ground-based and car-based DOAS observations. Main objectives are (1) to assess the operational capabilities of APEX to map the NO2 field over an urban area at high spatial and spectral resolution in a relatively short time and cost-effective way, and to characterise all aspects of the retrieval approach; (2) to use the APEX NO2 measurements

  19. Surface scattering properties estimated from modeling airborne multiple emission angle reflectance data

    NASA Technical Reports Server (NTRS)

    Guinness, Edward A.; Arvidson, Raymond E.; Irons, J. R.; Harding, D. J.

    1991-01-01

    Here, researchers apply the Hapke function to airborne bidirectional reflectance data collected over three terrestrial surfaces. The objectives of the study were to test the range of natural surfaces that the Hapke model fits and to evaluate model parameters in terms of known surface properties. The data used are multispectral and multiple emission angle data collected during the Geologic Remote Sensing Field Experiment (GRSFE) over a mud-cracked playa, an artificially roughened playa, and a basalt cobble strewn playa at Lunar Lake Playa in Nevada. Airborne remote sensing data and associated field measurements were acquired at the same time. The airborne data were acquired by the Advanced Solid State Array Spectroradiometer (ASAS) instrument, a 29-spectral band imaging system. ASAS reflectance data for a cobble-strewn surface and an artificially rough playa surface on Lunar Lake Playa can be explained with the Hanke model. The cobble and rough playa sites are distinguishable by a single scattering albedo, which is controlled by material composition; by the roughness parameter, which appears to be controlled by the surface texture and particle size; and the symmetry factor of the single particle phase function, which is controlled by particle size and shape. A smooth playa surface consisting of compacted, fine-grained particles has reflectance variations that are also distinct from either the cobble site or rough playa site. The smooth playa appears to behave more like a Lambertian surface that cannot be modeled with the Hapke function.

  20. Multispectral sensing of moisture stress

    NASA Technical Reports Server (NTRS)

    Olson, C. E., Jr.

    1970-01-01

    Laboratory reflectance data, and field tests with multispectral remote sensors provide support for this hypotheses that differences in moisture content and water deficits are closely related to foliar reflectance from woody plants. When these relationships are taken into account, automatic recognition techniques become more powerful than when they are ignored. Evidence is increasing that moisture relationships inside plant foliage are much more closely related to foliar reflectance characteristics than are external variables such as soil moisture, wind, and air temperature. Short term changes in water deficits seem to have little influence on foliar reflectance, however. This is in distinct contrast to significant short-term changes in foliar emittance from the same plants with changing wind, air temperature, incident radiation, or water deficit conditions.

  1. A multispectral hybrid HgCdTe FPA/dewar assembly for remote sensing in the Atmospheric Infrared Sounder (AIRS) instrument

    NASA Astrophysics Data System (ADS)

    Rutter, James H., Jr.; Jungkman, Dave; Stobie, James A.; Krueger, Eric E.; Garnett, James D.; Reine, Marion B.; Denley, Brian; Jasmin, Mark; Sofia, Anthony

    1996-10-01

    AIRS is a key instrument in NASA's Earth Observing System (EOS) Program. Passive IR remote sensing is performed using a high resolution grating spectrometer design with a wide spectral coverage focal plane assembly (FPA). The hybrid HgCdTe focal plane consists of twelve modules, ten photovoltaic (PV) and two photoconductive (PC), providing spectral response from 3.7 to 15.4 micrometers. The PV modules use silicon readout integrated circuits (ROICs) joined to the detector arrays as either direct or indirect hybrids. The PC modules are optically chopped and led out to warm electronics. Operating at 58 K, the sensitivity requirements approach BLIP in the critical 4.2 and 15.0 micrometer bands. The optical footprint coupled with the support and interface components of the focal plane make it a very large assembly, 53 mm multiplied by 66 mm. Dispersed energy from the grating is presented to the modules through 17 narrowband filters mounted 0.2 mm above the focal plane in a single, removable precision assembly. With PV and PC devices on the same focal plane operating simultaneously, shielding and lead routing as well as ROIC design have been optimized to minimize any interactions between them. Multilayer carriers have been designed to lead out the closely spaced PC arrays and the entire focal plane itself. Multilayer shielded flex cables are used to interconnect the focal plane to a very unique dewar. The tightly spaced optical pattern, along with more than 50 components in the focal plane, make this a highly complex assembly. The vacuum dewar, while providing approximately 600 leadouts, is directly coupled to the cold spectrometer and operates at 155 K while cooling the focal plane to 58 K via a sapphire rod interfaced to a pulse tube cooler. This paper discusses the key features of the FPA/dewar assembly, modeling/analyses done in support of the design, and results of design validation activities to date.

  2. Galileo multispectral imaging of Earth.

    PubMed

    Geissler, P; Thompson, W R; Greenberg, R; Moersch, J; McEwen, A; Sagan, C

    1995-08-25

    Nearly 6000 multispectral images of Earth were acquired by the Galileo spacecraft during its two flybys. The Galileo images offer a unique perspective on our home planet through the spectral capability made possible by four narrowband near-infrared filters, intended for observations of methane in Jupiter's atmosphere, which are not incorporated in any of the currently operating Earth orbital remote sensing systems. Spectral variations due to mineralogy, vegetative cover, and condensed water are effectively mapped by the visible and near-infrared multispectral imagery, showing a wide variety of biological, meteorological, and geological phenomena. Global tectonic and volcanic processes are clearly illustrated by these images, providing a useful basis for comparative planetary geology. Differences between plant species are detected through the narrowband IR filters on Galileo, allowing regional measurements of variation in the "red edge" of chlorophyll and the depth of the 1-micrometer water band, which is diagnostic of leaf moisture content. Although evidence of life is widespread in the Galileo data set, only a single image (at approximately 2 km/pixel) shows geometrization plausibly attributable to our technical civilization. Water vapor can be uniquely imaged in the Galileo 0.73-micrometer band, permitting spectral discrimination of moist and dry clouds with otherwise similar albedo. Surface snow and ice can be readily distinguished from cloud cover by narrowband imaging within the sensitivity range of Galileo's silicon CCD camera. Ice grain size variations can be mapped using the weak H2O absorption at 1 micrometer, a technique which may find important applications in the exploration of the moons of Jupiter. The Galileo images have the potential to make unique contributions to Earth science in the areas of geological, meteorological and biological remote sensing, due to the inclusion of previously untried narrowband IR filters. The vast scale and near global

  3. Remote sensing and image interpretation

    NASA Technical Reports Server (NTRS)

    Lillesand, T. M.; Kiefer, R. W. (Principal Investigator)

    1979-01-01

    A textbook prepared primarily for use in introductory courses in remote sensing is presented. Topics covered include concepts and foundations of remote sensing; elements of photographic systems; introduction to airphoto interpretation; airphoto interpretation for terrain evaluation; photogrammetry; radiometric characteristics of aerial photographs; aerial thermography; multispectral scanning and spectral pattern recognition; microwave sensing; and remote sensing from space.

  4. Implementation and operation of three fractal measurement algorithms for analysis of remote-sensing data

    NASA Technical Reports Server (NTRS)

    Jaggi, S.; Quattrochi, Dale A.; Lam, Nina S.-N.

    1993-01-01

    Fractal geometry is increasingly becoming a useful tool for modeling natural phenomena. As an alternative to Euclidean concepts, fractals allow for a more accurate representation of the nature of complexity in natural boundaries and surfaces. The purpose of this paper is to introduce and implement three algorithms in C code for deriving fractal measurement from remotely sensed data. These three methods are: the line-divider method, the variogram method, and the triangular prism method. Remote-sensing data acquired by NASA's Calibrated Airborne Multispectral Scanner (CAMS) are used to compute the fractal dimension using each of the three methods. These data were obtained as a 30 m pixel spatial resolution over a portion of western Puerto Rico in January 1990. A description of the three methods, their implementation in PC-compatible environment, and some results of applying these algorithms to remotely sensed image data are presented.

  5. Active and passive multispectral scanner for earth resources applications: An advanced applications flight experiment

    NASA Technical Reports Server (NTRS)

    Hasell, P. G., Jr.; Peterson, L. M.; Thomson, F. J.; Work, E. A.; Kriegler, F. J.

    1977-01-01

    The development of an experimental airborne multispectral scanner to provide both active (laser illuminated) and passive (solar illuminated) data from a commonly registered surface scene is discussed. The system was constructed according to specifications derived in an initial programs design study. The system was installed in an aircraft and test flown to produce illustrative active and passive multi-spectral imagery. However, data was not collected nor analyzed for any specific application.

  6. A13K-0336: Airborne Multi-Wavelength High Spectral Resolution Lidar for Process Studies and Assessment of Future Satellite Remote Sensing Concepts

    NASA Technical Reports Server (NTRS)

    Hostetler, Chris A.; Ferrare, Rich A.; Hair, Johnathan W.; Cook, Anthony L.; Harper, David B.; Mack, Terry L.; Hare, Richard J.; Cleckner, Craig S.; Rogers, Raymond R.; Muller, Detlef; Chemyakin, Eduard; Burton, Sharon P.; Obland, Michael D.; Scarino, Amy J.; Cairns, Brian; Russell, Phil; Redermann, Jens; Shinozuka, Y.; Schmid, Beat; Fast, Jerome; Berg, Larry; Flynn, Connor; Wagener, Rick; Gregory, Laurie

    2012-01-01

    NASA Langley recently developed the world's first airborne multi-wavelength high spectral resolution lidar (HSRL). This lidar employs the HSRL technique at 355 and 532 nm to make independent, unambiguous retrievals of aerosol extinction and backscatter. It also employs the standard backscatter technique at 1064 nm and is polarization-sensitive at all three wavelengths. This instrument, dubbed HSRL-2 (the secondgeneration HSRL developed by NASA Langley), is a prototype for the lidar on NASA's planned Aerosols- Clouds-Ecosystems (ACE) mission. HSRL-2 completed its first science mission in July 2012, the Two-Column Aerosol Project (TCAP) conducted by the Department of Energy (DOE) in Hyannis, MA. TCAP presents an excellent opportunity to assess some of the remote sensing concepts planned for ACE: HSRL-2 was deployed on the Langley King Air aircraft with another ACE-relevant instrument, the NASA GISS Research Scanning Polarimeter (RSP), and flights were closely coordinated with the DOE's Gulfstream-1 aircraft, which deployed a variety of in situ aerosol and trace gas instruments and the new Spectrometer for Sky-Scanning, Sun-Tracking Atmospheric Research (4STAR). The DOE also deployed their Atmospheric Radiation Measurement Mobile Facility and their Mobile Aerosol Observing System at a ground site located on the northeastern coast of Cape Cod for this mission. In this presentation we focus on the capabilities, data products, and applications of the new HSRL-2 instrument. Data products include aerosol extinction, backscatter, depolarization, and optical depth; aerosol type identification; mixed layer depth; and rangeresolved aerosol microphysical parameters (e.g., effective radius, index of refraction, single scatter albedo, and concentration). Applications include radiative closure studies, studies of aerosol direct and indirect effects, investigations of aerosol-cloud interactions, assessment of chemical transport models, air quality studies, present (e.g., CALIPSO

  7. Airborne infrared video radiometry as a low-cost tool for remote sensing of the environment, two mapping examples from Israel of urban heat islands and mineralogical site

    SciTech Connect

    Ben-Dor, E.; Saaroni, H.; Ochana, D.

    1996-10-01

    In this study we examined the capability of a laboratory infrared video camera for use in remote sensing of the environment. The instrument used, INFRAMETRICS 760, was mounted onboard a Bell 206 helicopter. Under the flight conditions examined, the radiometer proved itself to be very stable and produced high-quality thermal images in a real-time mode. We studied two different environmental aspects, as follows: (1) Urban heat island of the most dense city in Israel, Tel-Aviv- and (2) lithological distribution of a well-known mineralogical site in Israel, Makhtesh Ramon. The radiometer used in both studies was able to produce a temperature presentation, rather than a gray scale from an altitude of 7,000 and 10,000 feet and at 70 knots air speed. The instrument produced a high-quality set of data in terms of signal-to-noise, stability, temperature accuracy and spatial resolution. In the Tel-Aviv case, the results showed that the urban heat island of the city can be depicted in a very high spatial and thermal resolutions domain and that a significant correlation exists between ground objects and the surrounding air temperature values. Based on the flight results, we could generated an isotherm map of the city that, for the first time, located the urban heat island of the city both in meso- and microscales. In the case of Makhtesh Ramon, we found that under field conditions, the radiometer, coupled with a VIS-CCD camera can provide significant ATI parameters of typical rocks that characterize tile study area. Although more study is planned and suggested based on the current data, it was concluded that the airborne thermal video radiometry, is a promising, inexpensive tool for monitoring the environment on a real-time basis. 10 refs., 5 figs., 1 tab.

  8. Extrapolation of in situ data from 1-km squares to adjacent squares using remote sensed imagery and airborne lidar data for the assessment of habitat diversity and extent.

    PubMed

    Lang, M; Vain, A; Bunce, R G H; Jongman, R H G; Raet, J; Sepp, K; Kuusemets, V; Kikas, T; Liba, N

    2015-03-01

    Habitat surveillance and subsequent monitoring at a national level is usually carried out by recording data from in situ sample sites located according to predefined strata. This paper describes the application of remote sensing to the extension of such field data recorded in 1-km squares to adjacent squares, in order to increase sample number without further field visits. Habitats were mapped in eight central squares in northeast Estonia in 2010 using a standardized recording procedure. Around one of the squares, a special study site was established which consisted of the central square and eight surrounding squares. A Landsat-7 Enhanced Thematic Mapper Plus (ETM+) image was used for correlation with in situ data. An airborne light detection and ranging (lidar) vegetation height map was also included in the classification. A series of tests were carried out by including the lidar data and contrasting analytical techniques, which are described in detail in the paper. Training accuracy in the central square varied from 75 to 100 %. In the extrapolation procedure to the surrounding squares, accuracy varied from 53.1 to 63.1 %, which improved by 10 % with the inclusion of lidar data. The reasons for this relatively low classification accuracy were mainly inherent variability in the spectral signatures of habitats but also differences between the dates of imagery acquisition and field sampling. Improvements could therefore be made by better synchronization of the field survey and image acquisition as well as by dividing general habitat categories (GHCs) into units which are more likely to have similar spectral signatures. However, the increase in the number of sample kilometre squares compensates for the loss of accuracy in the measurements of individual squares. The methodology can be applied in other studies as the procedures used are readily available. PMID:25648761

  9. Using Airborne Microwave Remotely Sensed Root-Zone Soil Moisture and Flux Measurements to Improve Regional Predictions of Carbon Fluxes in a Terrestrial Biosphere Model

    NASA Astrophysics Data System (ADS)

    Zhang, K.; Antonarakis, A. S.; Medvigy, D.; Burgin, M. S.; Crow, W. T.; Milak, S.; Jaruwatanadilok, S.; Truong-Loi, M.; Moghaddam, M.; Saatchi, S. S.; Cuenca, R. H.; Moorcroft, P. R.

    2013-12-01

    North American ecosystems are critical components of the global carbon cycle, exchanging large amounts of carbon dioxide and other gases with the atmosphere. Net ecosystem exchange (NEE) of CO2 between atmosphere and ecosystems quantifies these carbon fluxes, but current continental-scale estimates contain high levels of uncertainty. Root-zone soil moisture (RZSM) and its spatial and temporal heterogeneity influences NEE and improved estimates can help reduce uncertainty in NEE estimates. We used the RZSM measurements from the Airborne Microwave Observatory of Subcanopy and Subsurface (AirMOSS) mission, and the carbon, water and energy fluxes observed by the eddy-covariance flux towers to constrain the Ecosystem Demography Model 2.2 (ED2.2) to improve its predictions of carbon fluxes. The parameters of the ED2.2 model were first optimized at seven flux tower sites in North America, which represent six different biomes, by constraining the model against a suite of flux measurements and forest inventory measurements through a Bayesian Markov-Chain Monte Carlo framework. We further applied the AirMOSS RZSM products to constrain the ED2.2 model to achieve better estimates of regional NEE. Evaluation against flux tower measurements and forest dynamics measurements shows that the constrained ED2.2 model produces improved predictions of monthly to annual carbon fluxes. The remote sensing based RZSM can further help improve the spatial patterns and temporal variations of model NEE. The results demonstrate that model-data fusion can substantially improve model performance and highlight the important role of RZSM in regulating the spatial and temporal heterogeneities of carbon fluxes.

  10. Environmental hazards and distribution of radioactive black sand along the Rosetta coastal zone in Egypt using airborne spectrometric and remote sensing data.

    PubMed

    Kaiser, M F; Aziz, A M; Ghieth, B M

    2014-11-01

    High-resolution airborne gamma ray spectrometry, conducted in 2003, was used to estimate radioactive elements spatial abundance along the Rosetta coastal zone area. It was noticed that both Uranium and Thorium are concentrated in the black sand deposits along the beach. In contrary, Potassium was observed in high level abundance at the cultivated Nile Delta lands due to the accumulated usage of fertilizers. Exposure Rate (ER), Absorbed Dose Rate (ADR) and Annual Effective Dose Rate (AEDR) were calculated to evaluate the radiation background influence in human. Results indicated that the human body in the study sites is subjected to radiation hazards exceeds the accepted limit for long duration exposure. In addition, the areas covered by the highest concentration of Uranium and Thorium show the highest level of radiogenic heat production. Detection the environmental hazards of the radioactive black sands in the study site encouraged this research to monitor the spatial and temporal distribution of these sediments. The Landsat Thematic Mapper images acquired in 1990, 2003 and 2013 were analyzed using remote sensing image processing techniques. Image enhancements, classification and changes detection indicated a positive significant relationship between the patterns of coastline changes and distribution of the radioactive black sand in the study sites. The radioactive black sands are usually concentrated in the eroded areas. Therefore, in 1990 high concentration of the radioactive black sands were observed along the eastern and western flanks of the Rosetta promontory. Distribution of these sediments decreased due to the construction of the protective sea walls. Most of the radioactive black sands are transported toward the east in Abu Khashaba bay under the effect of the longshore currents and toward the west in Alexandria and Abu Quir bay under the action of the seasonal reverse currents. PMID:25011074

  11. A stratospheric intrusion at the subtropical jet over the Mediterranean Sea: air-borne remote sensing observations and model results

    NASA Astrophysics Data System (ADS)

    Weigel, K.; Hoffmann, L.; Günther, G.; Khosrawi, F.; Olschewski, F.; Preusse, P.; Spang, R.; Stroh, F.; Riese, M.

    2012-09-01

    Remote sensing measurements from the Cryogenic Infrared Spectrometers and Telescope for the Atmosphere - New Frontiers (CRISTA-NF) during a flight on 29 July 2006 are presented. This flight is part of the AMMA-SCOUT-O3 measurement campaign, where CRISTA-NF was deployed on the high-flying research aircraft M55-Geophysica. The flight path was located over Italy and the Mediterranean Sea and crossed over the subtropical jet twice. Measurements of temperature, and the volume mixing ratios of water vapor (H2O), ozone (O3), nitric acid (HNO3) and peroxyacetyl nitrate (PAN) are available with a vertical resolution of up to 500 m between about 6 to 21 km altitude. CRISTA-NF observes these trace gases simultaneously and provides a quasi-2-D view of the transition region between the troposphere and the stratosphere. The observation of these different trace gases allows to determine tropospheric and stratospheric air masses. As expected, higher abundances are found where the main source of the trace gases is located: in the stratosphere for O3 and in the troposphere for H2O and PAN. Tracer-tracer correlations between O3 and PAN are used to identify the mixed tropospheric and lowermost stratospheric air at the subtropical jet and around the thermal tropopause north of the jet. An intrusion of stratospheric air into the troposphere associated with the subtropical jet is found in the CRISTA-NF observations. The observations indicate that the intrusion is connected to a tropopause fold which is not resolved in the ECMWF analysis data. The intrusion was reproduced in a simulation with the Chemical Lagrangian Model of the Stratosphere (CLaMS). The CLaMS simulation shows, that the lowermost stratospheric air masses in the intrusion where transported along the the subtropical jet. The tropospheric air masses around the intrusion originate from the vicinity of the Asian monsoon anticyclone. This work discusses the nature of the observed processes at the subtropical jet based on the

  12. An Approach to Application Validation of Multispectral Sensors Using AVIRIS

    NASA Technical Reports Server (NTRS)

    Warner, Amanda; Blonski, Slawomir; Gasser, Gerald; Ryan, Robert; Zanoni, Vicki

    2001-01-01

    High-resolution multispectral data are becoming widely available for commercial and scientific use. For specific applications, such as agriculture studies, there is a need to quantify the performance of such systems. In many cases, parameters such as GSD and SNR can be optimized. Data sets with varying GSD's for the Landsat ETM+ bands were produced to evaluate the effects of GSD on various algorithms and transformations, such as NDVI, principal component analysis, unsupervised classification, and mixture analysis. By showing that AVIRIS data can be used to simulate spaceborne and airborne multispectral platforms over a wide range of GSD, this research can be used to assist in band selection and spatial resolution specifications for new sensors and in optimization of acquisition strategies for existing multispectral systems.

  13. Calibration of passive remote observing optical and microwave instrumentation; Proceedings of the Meeting, Orlando, FL, Apr. 3-5, 1991

    NASA Technical Reports Server (NTRS)

    Guenther, Bruce W. (Editor)

    1991-01-01

    Various papers on the calibration of passive remote observing optical and microwave instrumentation are presented. Individual topics addressed include: on-board calibration device for a wide field-of-view instrument, calibration for the medium-resolution imaging spectrometer, cryogenic radiometers and intensity-stabilized lasers for EOS radiometric calibrations, radiometric stability of the Shuttle-borne solar backscatter ultraviolet spectrometer, ratioing radiometer for use with a solar diffuser, requirements of a solar diffuser and measurements of some candidate materials, reflectance stability analysis of Spectralon diffuse calibration panels, stray light effects on calibrations using a solar diffuser, radiometric calibration of SPOT 23 HRVs, surface and aerosol models for use in radiative transfer codes. Also addressed are: calibrated intercepts for solar radiometers used in remote sensor calibration, radiometric calibration of an airborne multispectral scanner, in-flight calibration of a helicopter-mounted Daedalus multispectral scanner, technique for improving the calibration of large-area sphere sources, remote colorimetry and its applications, spatial sampling errors for a satellite-borne scanning radiometer, calibration of EOS multispectral imaging sensors and solar irradiance variability.

  14. Multispectral photography for earth resources

    NASA Technical Reports Server (NTRS)

    Wenderoth, S.; Yost, E.; Kalia, R.; Anderson, R.

    1972-01-01

    A guide for producing accurate multispectral results for earth resource applications is presented along with theoretical and analytical concepts of color and multispectral photography. Topics discussed include: capabilities and limitations of color and color infrared films; image color measurements; methods of relating ground phenomena to film density and color measurement; sensitometry; considerations in the selection of multispectral cameras and components; and mission planning.

  15. Lightweight Vertical Take-Off & Landing Unmanned Aerial Systems For Local-Scale Forestry and Agriculture Remote Sensing Data Collection

    NASA Astrophysics Data System (ADS)

    Putman, E.; Sheridan, R.; Popescu, S. C.

    2015-12-01

    The evolution of lightweight Vertical Take-Off and Landing (VTOL) rotary Unmanned Aerial Vehicles (UAVs) and remote sensor technologies have provided researchers with the ability to integrate compact remote sensing systems with UAVs to create Unmanned Aerial Systems (UASs) capable of collecting high-resolution airborne remote sensing data. UASs offer a myriad of benefits. Some of the most notable include: (1) reduced operational cost; (2) reduced lead-time for mission planning; (3) high-resolution and high-density data collection; and (4) customization of data collection intervals to fit the needs of a specific project (i.e. acquiring data at hourly, daily, or weekly intervals). Such benefits allow researchers and natural resource managers to acquire airborne remote sensing data on local-scale phenomenon in ways that were previously cost-prohibitive. VTOL UASs also offer a stable platform capable of low speed low altitude flight over small spatial scales that do not require a dedicated runway. Such flight characteristics allow VTOL UASs to collect high-resolution data at very high densities, enabling the use of structure from motion (SFM) techniques to generate three-dimensional datasets from photographs. When combined, these characteristics make VTOL UASs ideal for collecting data over agricultural or forested research areas. The goal of this study is to provide an overview of several lightweight eight-rotor VTOL UASs designed for small-scale forest remote sensing data collection. Specific objectives include: (1) the independent integration of a lightweight multispectral camera, a lightweight scanning lidar sensor, with required components (i.e. IMU, GPS, data logger) and the UAV; (2) comparison of UAS-collected data to terrestrial lidar data and airborne multispectral and lidar data; (3) comparison of UAS SFM techniques to terrestrial lidar data; and (4) multi-temporal assessment of tree decay using terrestrial lidar and UAS SfM techniques.

  16. Multispectral imaging probe

    SciTech Connect

    Sandison, David R.; Platzbecker, Mark R.; Descour, Michael R.; Armour, David L.; Craig, Marcus J.; Richards-Kortum, Rebecca

    1999-01-01

    A multispectral imaging probe delivers a range of wavelengths of excitation light to a target and collects a range of expressed light wavelengths. The multispectral imaging probe is adapted for mobile use and use in confined spaces, and is sealed against the effects of hostile environments. The multispectral imaging probe comprises a housing that defines a sealed volume that is substantially sealed from the surrounding environment. A beam splitting device mounts within the sealed volume. Excitation light is directed to the beam splitting device, which directs the excitation light to a target. Expressed light from the target reaches the beam splitting device along a path coaxial with the path traveled by the excitation light from the beam splitting device to the target. The beam splitting device directs expressed light to a collection subsystem for delivery to a detector.

  17. Multispectral imaging probe

    DOEpatents

    Sandison, D.R.; Platzbecker, M.R.; Descour, M.R.; Armour, D.L.; Craig, M.J.; Richards-Kortum, R.

    1999-07-27

    A multispectral imaging probe delivers a range of wavelengths of excitation light to a target and collects a range of expressed light wavelengths. The multispectral imaging probe is adapted for mobile use and use in confined spaces, and is sealed against the effects of hostile environments. The multispectral imaging probe comprises a housing that defines a sealed volume that is substantially sealed from the surrounding environment. A beam splitting device mounts within the sealed volume. Excitation light is directed to the beam splitting device, which directs the excitation light to a target. Expressed light from the target reaches the beam splitting device along a path coaxial with the path traveled by the excitation light from the beam splitting device to the target. The beam splitting device directs expressed light to a collection subsystem for delivery to a detector. 8 figs.

  18. Use of field and airborne advanced remote sensing data for the characterisation of surface erosional stages in agricultural semi-arid soils (central Spain) at various scales

    NASA Astrophysics Data System (ADS)

    Milewski, Robert; Chabrillat, Sabine; Schmid, Thomas; Rodriguez, Manuel; Schuett, Brigitta

    2014-05-01

    The interest in the use of non-invasive remote sensing methods such as visible-near infrared reflectance spectroscopy for the remote determination of mineralogical composition in soils and planetary surfaces has been demonstrated since the 1970s with the development of databases in the laboratory of minerals spectra. Nowadays, quantitative soil spectroscopy has been shown to be a powerful tool for the identification and prediction of soil properties, and has been used in many soil science applications. With the upcoming launch of the next generation of hyperspectral satellite systems such as the German EnMAP (Environmental Mapping) satellite in 2017, new potential toward the quantitative analyses of chemical and physical soil attributes of the Earth's soil surface composition based on reflectance spectroscopy will be opened. In particular, in arid and semi-arid agricultural regions sensitive to soil erosion processes, the analyses of the spatial distribution of combined varying surface soil properties based on advanced hyperspectral methodology could be used to infer erosion and deposition stages in selected areas, although it was never thoroughly demonstrated. To fully utilize the potential of this technology for the assessment of surface soil erosional stages, new adapted approaches have to be developed, providing the context for this study. This research focuses on a semi-arid, agricultural area in Central Spain near Toledo and Madrid, in which airborne hyperspectral and LiDAR data have been obtained. The study area is under the influence of a Mediterranean climate with extended agricultural rainfed uses on mostly evolved soils. There, soil erosion features can be observed that are representative for areas throughout Southern Europe. Such erosion features are associated with different soil horizons and rock outcrops with contrasted physical and chemical characteristic. They are exposed at the surface as a consequence of human induced soil erosion which is

  19. COMPUTER PROCESSING OF MULTISPECTRAL SCANNER DATA OVER COAL STRIP MINES

    EPA Science Inventory

    There is little doubt that remote sensing techniques can be effectively applied to the task of monitoring coal strip mine progress and reclamation work. Aircraft multispectral scanner data acquired over six coal strip mines in the states of Wyoming, Montana, Colorado, and Arizona...

  20. ADP of multispectral scanner data for land use mapping

    NASA Technical Reports Server (NTRS)

    Hoffer, R. M.

    1971-01-01

    The advantages and disadvantages of various remote sensing instrumentation and analysis techniques are reviewed. The use of multispectral scanner data and the automatic data processing techniques are considered. A computer-aided analysis system for remote sensor data is described with emphasis on the image display, statistics processor, wavelength band selection, classification processor, and results display. Advanced techniques in using spectral and temporal data are also considered.

  1. Multispectral analysis of ocean dumped materials

    NASA Technical Reports Server (NTRS)

    Johnson, R. W.

    1977-01-01

    Remotely sensed data were collected in conjunction with sea-truth measurements in three experiments in the New York Bight. Pollution features of primary interest were ocean dumped materials, such as sewage sludge and acid waste. Sewage-sludge and acid-waste plumes, including plumes from sewage sludge dumped by the 'line-dump' and 'spot-dump' methods, were located, identified, and mapped. Previously developed quantitative analysis techniques for determining quantitative distributions of materials in sewage sludge dumps were evaluated, along with multispectral analysis techniques developed to identify ocean dumped materials. Results of these experiments and the associated data analysis investigations are presented and discussed.

  2. International Symposium on Remote Sensing of Environment, 8th, University of Michigan, Ann Arbor, Mich., October 2-6, 1972, Proceedings. Volumes 1 & 2.

    NASA Technical Reports Server (NTRS)

    1973-01-01

    Recent developments in remote sensing techniques and applications are described in papers dealing with (1) ground-based, airborne, and space-borne sensor systems, (2) machine assisted data analysis and interpretation, and (3) specific uses of sensing techniques by various government units. Topics covered include monitoring of environmental quality factors, delineation of geological formations and mineral deposits, watershed management, observation of vegetative parameters in forestry and agriculture, design and performance details of various sensor systems and equipment, interpretation of multispectral imagery, and applications of ERTS-1 satellite imagery in resource study programs. Individual items are announced in this issue.

  3. A multi-sensor lidar, multi-spectral and multi-angular approach for mapping canopy height in boreal forest regions

    USGS Publications Warehouse

    Selkowitz, David J.; Green, Gordon; Peterson, Birgit; Wylie, Bruce

    2012-01-01

    Spatially explicit representations of vegetation canopy height over large regions are necessary for a wide variety of inventory, monitoring, and modeling activities. Although airborne lidar data has been successfully used to develop vegetation canopy height maps in many regions, for vast, sparsely populated regions such as the boreal forest biome, airborne lidar is not widely available. An alternative approach to canopy height mapping in areas where airborne lidar data is limited is to use spaceborne lidar measurements in combination with multi-angular and multi-spectral remote sensing data to produce comprehensive canopy height maps for the entire region. This study uses spaceborne lidar data from the Geosciences Laser Altimeter System (GLAS) as training data for regression tree models that incorporate multi-angular and multi-spectral data from the Multi-Angle Imaging Spectroradiometer (MISR) and the Moderate Resolution Imaging SpectroRadiometer (MODIS) to map vegetation canopy height across a 1,300,000 km2 swath of boreal forest in Interior Alaska. Results are compared to in situ height measurements as well as airborne lidar data. Although many of the GLAS-derived canopy height estimates are inaccurate, applying a series of filters incorporating both data associated with the GLAS shots as well as ancillary data such as land cover can identify the majority of height estimates with significant errors, resulting in a filtered dataset with much higher accuracy. Results from the regression tree models indicate that late winter MISR imagery acquired under snow-covered conditions is effective for mapping canopy heights ranging from 5 to 15 m, which includes the vast majority of forests in the region. It appears that neither MISR nor MODIS imagery acquired during the growing season is effective for canopy height mapping, although including summer multi-spectral MODIS data along with winter MISR imagery does appear to provide a slight increase in the accuracy of resulting

  4. Multispectral metamaterial absorber.

    PubMed

    Grant, J; McCrindle, I J H; Li, C; Cumming, D R S

    2014-03-01

    We present the simulation, implementation, and measurement of a multispectral metamaterial absorber (MSMMA) and show that we can realize a simple absorber structure that operates in the mid-IR and terahertz (THz) bands. By embedding an IR metamaterial absorber layer into a standard THz metamaterial absorber stack, a narrowband resonance is induced at a wavelength of 4.3 μm. This resonance is in addition to the THz metamaterial absorption resonance at 109 μm (2.75 THz). We demonstrate the inherent scalability and versatility of our MSMMA by describing a second device whereby the MM-induced IR absorption peak frequency is tuned by varying the IR absorber geometry. Such a MSMMA could be coupled with a suitable sensor and formed into a focal plane array, enabling multispectral imaging. PMID:24690713

  5. Multispectral Image Feature Points

    PubMed Central

    Aguilera, Cristhian; Barrera, Fernando; Lumbreras, Felipe; Sappa, Angel D.; Toledo, Ricardo

    2012-01-01

    This paper presents a novel feature point descriptor for the multispectral image case Far-Infrared and Visible Spectrum images. It allows matching interest points on images of the same scene but acquired in different spectral bands. Initially, points of interest are detected on both images through a SIFT-like based scale space representation. Then, these points are characterized using an Edge Oriented Histogram (EOH) descriptor. Finally, points of interest from multispectral images are matched by finding nearest couples using the information from the descriptor. The provided experimental results and comparisons with similar methods show both the validity of the proposed approach as well as the improvements it offers with respect to the current state-of-the-art.

  6. Understanding land surface evapotranspiration with satellite multispectral measurements

    NASA Technical Reports Server (NTRS)

    Menenti, M.

    1993-01-01

    Quantitative use of remote multispectral measurements to study and map land surface evapotranspiration has been a challenging issue for the past 20 years. Past work is reviewed against process physics. A simple two-layer combination-type model is used which is applicable to both vegetation and bare soil. The theoretic analysis is done to show which land surface properties are implicitly defined by such evaporation models and to assess whether they are measurable as a matter of principle. Conceptual implications of the spatial correlation of land surface properties, as observed by means of remote multispectral measurements, are illustrated with results of work done in arid zones. A normalization of spatial variability of land surface evaporation is proposed by defining a location-dependent potential evaporation and surface temperature range. Examples of the application of remote based estimates of evaporation to hydrological modeling studies in Egypt and Argentina are presented.

  7. Thermal Remote Sensing and the Thermodynamics of Ecosystems Development

    NASA Technical Reports Server (NTRS)

    Luvall, Jeffrey C.; Kay, James J.; Fraser, Roydon F.; Goodman, H. Michael (Technical Monitor)

    2001-01-01

    Thermal remote sensing can provide environmental measuring tools with capabilities for measuring ecosystem development and integrity. Recent advances in applying principles of nonequilibrium thermodynamics to ecology provide fundamental insights into energy partitioning in ecosystems. Ecosystems are nonequilibrium systems, open to material and energy flows, which grow and develop structures and processes to increase energy degradation. More developed terrestrial ecosystems will be more effective at dissipating the solar gradient (degrading its energy content). This can be measured by the effective surface temperature of the ecosystem on a landscape scale. A series of airborne thermal infrared multispectral scanner data were collected from several forested ecosystems ranging from a western US douglas-fir forest to a tropical rain forest in Costa Rica. Also measured were agriculture systems. These data were used to develop measures of ecosystem development and integrity based on surface temperature.

  8. Detection and identification of Arctic landforms - An assessment of remotely sensed data

    NASA Technical Reports Server (NTRS)

    Dean, Kenneson G.; Morrissey, Leslie A.

    1988-01-01

    The use of remote sensing data to monitor and analyze the arctic environment is examined. Landsat MSS, TM simulated, NS001, Seasat, and airborne radar are employed to investigate the Strand and Dune areas on the Arctic Coastal Plain in Alaska. The Strand area contains landforms associated with permafrost and the Dune area is dominated by eolian deposits consisting of large longitudinal dunes. The remote sensing data are compared to baseline geomorphic maps derived from aerial photography. It is observed that the multispectral data are better than the radar data for the detection and recognition of arctic landforms, and the NS001 data provided the highest spatial resolution and correlated well with the high-altitude aerial photography.

  9. A preliminary report of multispectral scanner data from the Cleveland harbor study

    NASA Technical Reports Server (NTRS)

    Shook, D.; Raquet, C.; Svehla, R.; Wachter, D.; Salzman, J.; Coney, T.; Gedney, D.

    1975-01-01

    Imagery obtained from an airborne multispectral scanner is presented. A synoptic view of the entire study area is shown for a number of time periods and for a number of spectral bands. Using several bands, sediment distributions, thermal plumes, and Rhodamine B dye distributions are shown.

  10. Aerial multispectral imaging for cotton yield estimation under different irrigation and nitrogen treatments

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Cotton yield varied spatially within a field. The variability can be caused by various production inputs such as soil property, water management, and fertilizer application. Airborne multispectral imaging is capable of providing data and information to study effects of the inputs on the yield qualit...

  11. Estimation of cotton yield with varied irrigation and nitrogen treatments using aerial multispectral imagery

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Cotton yield varies spatially within a field. The variability can be caused by various production inputs such as soil properties, water management, and fertilizer application. Airborne multispectral imaging is capable of providing data and information to study effects of the inputs on yield qualitat...

  12. Use of multispectral scanner images for assessment of hydrothermal alteration in the Marysvale, Utah, mining area.

    USGS Publications Warehouse

    Podwysocki, M.H.; Segal, D.B.; Abrams, M.J.

    1983-01-01

    Airborne multispectral scanner. A color composite image was constructed using the following spectral band ratios: 1.6/2.2 mu m, 1.6/0.48 mu m, and 0.67/1.0 mu m. The color ratio composite successfully distinguished most types of altered rocks from unaltered rocks; further division of altered rocks into ferric oxide-rich and -poor types.

  13. Deriving Radiative Effects of Aerosol-Immersed Broken Cloud Fields from Multi-spectral Imagery

    NASA Astrophysics Data System (ADS)

    Schmidt, Sebastian

    2016-04-01

    Recently, significant progress has been made in the understanding of cloud inhomogeneity effects in shortwave passive remote sensing. Yet it has proven difficult to correct such effects on the pixel level using multi-spectral imagery alone, mainly because three-dimensional (3D) radiative transfer in cloud fields is a non-local phenomenon. As a result, estimates of irradiance - the fundamental climate variable - from space-or air-borne imagery continue to pose problems for complex cloud fields. The presence of aerosols in the vicinity of clouds exacerbates the prob- lem. I will show evidence from field experiments and 3D radiative transfer calculations that biases may exceed 40% at the pixel level at the MODIS spatial resolution, and that some of these effects "survive" spatial averaging. A new way to cope with this problem is the discovery that 3D effects manifest themselves as spectral perturba- tion in reflected radiances and in the associated irradiance fields throughout an inhomogeneous cloud domain. In parameterized form, these correlations between spatial cloud distribution and spectral signature can be used to de- rive first-order inhomogeneity corrections for irradiance fields - not on a pixel basis, but for populations of pixels within a cloud domain represented by probability density functions. I will present the first practical approach for using these new findings in a future proxy-3D algorithm for deriving irradiances below and above cloud-aerosol fields from multi-spectral imagers, and discuss the accuracy that can be expected from this simplified method to account for 3D effects in mixed aerosol-cloud scenes.

  14. Analysis of multispectral and hyperspectral longwave infrared (LWIR) data for geologic mapping

    NASA Astrophysics Data System (ADS)

    Kruse, Fred A.; McDowell, Meryl

    2015-05-01

    Multispectral MODIS/ASTER Airborne Simulator (MASTER) data and Hyperspectral Thermal Emission Spectrometer (HyTES) data covering the 8 - 12 μm spectral range (longwave infrared or LWIR) were analyzed for an area near Mountain Pass, California. Decorrelation stretched images were initially used to highlight spectral differences between geologic materials. Both datasets were atmospherically corrected using the ISAC method, and the Normalized Emissivity approach was used to separate temperature and emissivity. The MASTER data had 10 LWIR spectral bands and approximately 35-meter spatial resolution and covered a larger area than the HyTES data, which were collected with 256 narrow (approximately 17nm-wide) spectral bands at approximately 2.3-meter spatial resolution. Spectra for key spatially-coherent, spectrally-determined geologic units for overlap areas were overlain and visually compared to determine similarities and differences. Endmember spectra were extracted from both datasets using n-dimensional scatterplotting and compared to emissivity spectral libraries for identification. Endmember distributions and abundances were then mapped using Mixture-Tuned Matched Filtering (MTMF), a partial unmixing approach. Multispectral results demonstrate separation of silica-rich vs non-silicate materials, with distinct mapping of carbonate areas and general correspondence to the regional geology. Hyperspectral results illustrate refined mapping of silicates with distinction between similar units based on the position, character, and shape of high resolution emission minima near 9 μm. Calcite and dolomite were separated, identified, and mapped using HyTES based on a shift of the main carbonate emissivity minimum from approximately 11.3 to 11.2 μm respectively. Both datasets demonstrate the utility of LWIR spectral remote sensing for geologic mapping.

  15. Multispectral observations of the surf zone

    NASA Astrophysics Data System (ADS)

    Schoonmaker, Jon S.; Dirbas, Joseph; Gilbert, Gary

    2003-09-01

    Airborne multispectral imagery was collected over various targets on the beach and in the water in an attempt to characterize the surf zone environment with respect to electro-optical system capabilities and to assess the utility of very low cost, small multispectral systems in mine counter measures (MCM) and intelligence, surveillance and reconnaissance applications. The data was collected by PAR Government Systems Corporation (PGSC) at the Army Corps of Engineers Field Research Facility at Duck North Carolina and on the beaches of Camp Pendleton Marine Corps Base in Southern California. PGSC flew the first two of its MANTIS (Mission Adaptable Narrowband Tunable Imaging Sensor) systems. Both MANTIS systems were flown in an IR - red - green - blue (700, 600, 550, 480 nm) configuration from altitudes ranging from 200 to 700 meters. Data collected has been lightly analyzed and a surf zone index (SZI) defined and calculated. This index allows mine hunting system performance measurements in the surf zone to be normalized by environmental conditions. The SZI takes into account water clarity, wave energy, and foam persistence.

  16. Multispectral imaging with type II superlattice detectors

    NASA Astrophysics Data System (ADS)

    Ariyawansa, Gamini; Duran, Joshua M.; Grupen, Matt; Scheihing, John E.; Nelson, Thomas R.; Eismann, Michael T.

    2012-06-01

    Infrared (IR) focal plane arrays (FPAs) with multispectral detector elements promise significant advantages for airborne threat warning, surveillance, and targeting applications. At present, the use of type II superlattice (T2SL) structures based on the 6.1Å-family materials (InAs, GaSb, and AlSb) has become an area of interest for developing IR detectors and their FPAs. The ability to vary the bandgap in the IR range, suppression of Auger processes, prospective reduction of Shockley-Read-Hall centers by improved material growth capabilities, and the material stability are a few reasons for the predicted dominance of the T2SL technology over presently leading HgCdTe and quantum well technologies. The focus of the work reported here is on the development of T2SL based dual-band IR detectors and their applicability for multispectral imaging. A new NpBPN detector designed for the detection of IR in the 3-5 and 8-12 μm atmospheric windows is presented; comparing its advantages over other T2SL based approaches. One of the key challenges of the T2SL dual-band detectors is the spectral crosstalk associated with the LWIR band. The properties of the state-of-the-art T2SLs (i.e., absorption coefficient, minority carrier lifetime and mobility, etc.) and the present growth limitations that impact spectral crosstalk are discussed.

  17. Automated oil spill detection with multispectral imagery

    NASA Astrophysics Data System (ADS)

    Bradford, Brian N.; Sanchez-Reyes, Pedro J.

    2011-06-01

    In this publication we present an automated detection method for ocean surface oil, like that which existed in the Gulf of Mexico as a result of the April 20, 2010 Deepwater Horizon drilling rig explosion. Regions of surface oil in airborne imagery are isolated using red, green, and blue bands from multispectral data sets. The oil shape isolation procedure involves a series of image processing functions to draw out the visual phenomenological features of the surface oil. These functions include selective color band combinations, contrast enhancement and histogram warping. An image segmentation process then separates out contiguous regions of oil to provide a raster mask to an analyst. We automate the detection algorithm to allow large volumes of data to be processed in a short time period, which can provide timely oil coverage statistics to response crews. Geo-referenced and mosaicked data sets enable the largest identified oil regions to be mapped to exact geographic coordinates. In our simulation, multispectral imagery came from multiple sources including first-hand data collected from the Gulf. Results of the simulation show the oil spill coverage area as a raster mask, along with histogram statistics of the oil pixels. A rough square footage estimate of the coverage is reported if the image ground sample distance is available.

  18. Pedestrian detection by multispectral fusion

    NASA Astrophysics Data System (ADS)

    Ma, Yunqian; Wang, Zheng; Bazakos, Mike

    2006-04-01

    Security systems increasingly rely on the use of Automated Video Surveillance (AVS) technology. In particular the use of digital video renders itself to internet and local communications, remote monitoring, and to computer processing. AVS systems can perform many tedious and repetitive tasks currently performed by trained security personnel. AVS technology has already made some significant steps towards automating some basic security functions such as: motion detection, object tracking and event-based video recording. However, there are still many problems associated with just these automated functions, which need to be addressed further. Some examples of these problems are: the high "false alarm rate" and the "loss of track" under total or partial occlusion, when used under a wide range of operational parameters (day, night, sunshine, cloudy, foggy, range, viewing angle, clutter, etc.). Current surveillance systems work well only under a narrow range of operational parameters. Therefore, they need be hardened against a wide range of operational conditions. In this paper, we present a Multi-spectral fusion approach to perform accurate pedestrian segmentation under varying operational parameters. Our fusion method combines the "best" detection results from the visible images and the "best" from the thermal images. Commonly, the motion detection results in the visible images are easily affected by noise and shadows. The objects in the thermal image are relatively stable, but they may be missing some parts of the objects, because they thermally blend with the background. Our method makes use of the "best" object components and de-emphasize the "not best".

  19. Scene/object classification using multispectral data fusion algorithms

    NASA Astrophysics Data System (ADS)

    Kuzma, Thomas J.; Lazofson, Laurence E.; Choe, Howard C.; Chovan, John D.

    1994-06-01

    Near-simultaneous, multispectral, coregistered imagery of ground target and background signatures were collected over a full diurnal cycle in visible, infrared, and ultraviolet spectrally filtered wavebands using Battelle's portable sensor suite. The imagery data were processed using classical statistical algorithms, artificial neural networks and data clustering techniques to classify objects in the imaged scenes. Imagery collected at different times throughout the day were employed to verify algorithm robustness with respect to temporal variations of spectral signatures. In addition, several multispectral sensor fusion medical imaging applications were explored including imaging of subcutaneous vasculature, retinal angiography, and endoscopic cholecystectomy. Work is also being performed to advance the state of the art using differential absorption lidar as an active remote sensing technique for spectrally detecting, identifying, and tracking hazardous emissions. These investigations support a wide variety of multispectral signature discrimination applications including the concepts of automated target search, landing zone detection, enhanced medical imaging, and chemical/biological agent tracking.

  20. Characteristic variogram for land use in Multispectral Images

    NASA Astrophysics Data System (ADS)

    Mera, E.; Condal, A.; Rios, C.; Da Silva, L.

    2016-05-01

    In remote sensing is the concept of spectral signature in multispectral imagery to recognize different land uses in the area; This study proposes the existence of a characteristic variogram for land use in multispectral images. To test this idea we proceeded to work with a sector of a scene image of multispectral Landsat 7 ETM +, in 6 of their bands (1- 450nm to 520nm, 2 - 520nm to 600nm, 3 - 630nm to 690nm, 4 - 760nm to 900nm 5 - over 1550nm to 1.750nm and 7 - 2.080nm to 2.350nm), corresponding to two uses of urban land and agricultural, the omnidirectional variogram for each band was analyzed and modal variogram for each land use was established in the stripe set. Of the analyzed claims data for each land use is a model characteristic and modal cross variogram how their wavelengths.