Science.gov

Sample records for airborne repeat track

  1. Airborne ballistic camera tracking systems

    NASA Technical Reports Server (NTRS)

    Redish, W. L.

    1976-01-01

    An operational airborne ballistic camera tracking system was tested for operational and data reduction feasibility. The acquisition and data processing requirements of the system are discussed. Suggestions for future improvements are also noted. A description of the data reduction mathematics is outlined. Results from a successful reentry test mission are tabulated. The test mission indicated that airborne ballistic camera tracking systems are feasible.

  2. Airborne Radar Interferometric Repeat-Pass Processing

    NASA Technical Reports Server (NTRS)

    Hensley, Scott; Michel, Thierry R.; Jones, Cathleen E.; Muellerschoen, Ronald J.; Chapman, Bruce D.; Fore, Alexander; Simard, Marc; Zebker, Howard A.

    2011-01-01

    Earth science research often requires crustal deformation measurements at a variety of time scales, from seconds to decades. Although satellites have been used for repeat-track interferometric (RTI) synthetic-aperture-radar (SAR) mapping for close to 20 years, RTI is much more difficult to implement from an airborne platform owing to the irregular trajectory of the aircraft compared with microwave imaging radar wavelengths. Two basic requirements for robust airborne repeat-pass radar interferometry include the ability to fly the platform to a desired trajectory within a narrow tube and the ability to have the radar beam pointed in a desired direction to a fraction of a beam width. Uninhabited Aerial Vehicle Synthetic Aperture Radar (UAVSAR) is equipped with a precision auto pilot developed by NASA Dryden that allows the platform, a Gulfstream III, to nominally fly within a 5 m diameter tube and with an electronically scanned antenna to position the radar beam to a fraction of a beam width based on INU (inertial navigation unit) attitude angle measurements.

  3. Airborne optical tracking control system design study

    NASA Astrophysics Data System (ADS)

    1992-09-01

    The Kestrel LOS Tracking Program involves the development of a computer and algorithms for use in passive tracking of airborne targets from a high altitude balloon platform. The computer receivers track error signals from a video tracker connected to one of the imaging sensors. In addition, an on-board IRU (gyro), accelerometers, a magnetometer, and a two-axis inclinometer provide inputs which are used for initial acquisitions and course and fine tracking. Signals received by the control processor from the video tracker, IRU, accelerometers, magnetometer, and inclinometer are utilized by the control processor to generate drive signals for the payload azimuth drive, the Gimballed Mirror System (GMS), and the Fast Steering Mirror (FSM). The hardware which will be procured under the LOS tracking activity is the Controls Processor (CP), the IRU, and the FSM. The performance specifications for the GMS and the payload canister azimuth driver are established by the LOS tracking design team in an effort to achieve a tracking jitter of less than 3 micro-rad, 1 sigma for one axis.

  4. BOREAS RSS-12 Airborne Tracking Sunphotometer Measurements

    NASA Technical Reports Server (NTRS)

    Hall, Forrest G. (Editor); Nickeson, Jaime (Editor); Lobitz, Brad; Spanner, Michael; Wrigley, Robert

    2000-01-01

    The BOREAS RSS-12 team collected both ground and airborne sunphotometer measurements for use in characterizing the aerosol optical properties of the atmosphere during the BOREAS data collection activities. These measurements are to be used to: 1) measure the magnitude and variability of the aerosol optical depth in both time and space; 2) determine the optical properties of the boreal aerosols; and 3) atmospherically correct remotely sensed data acquired during BOREAS. This data set contains airborne tracking sunphotometer data that were acquired from the C-130 aircraft during its flights over the BOREAS study areas. The data cover selected days and times from May to September 1994. The data are stored in tabular ASCII files. The data files are available on a CD-ROM (see document number 20010000884), or from the Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC).

  5. Multiple model adaptive tracking of airborne targets

    NASA Astrophysics Data System (ADS)

    Norton, John E.

    1988-12-01

    Over the past ten years considerable work has been accomplished at the Air Force Institute of Technology (AFIT) towards improving the ability of tracking airborne targets. Motivated by the performance advantages in using established models of tracking environment variables within a Kalman filter, an advanced tracking algorithm has been developed based on adaptive estimation filter structures. A multiple model bank of filters that have been designed for various target dynamics, which each accounting for atmospheric disturbance of the Forward Looking Infrared (FLIR) sensor data and mechanical vibrations of the sensor platform, outperforms a correlator tracker. The bank of filters provides the estimation capability to guide the pointing mechanisms of a shared aperture laser/sensor system. The data is provided to the tracking algorithm via an (8 x 8)-pixel tracking Field of View (FOV) from the FLIR image plane. Data at each sample period is compared by an enhanced correlator to a target template. These offsets are measurements to a bank of linear Kalman filters which provide estimates of the target's location in azimuth and elevation coordinates based on a Gauss-Markov acceleration model, and a reduced form of the atmospheric jitter model for the disturbance in the IR wavefront carrying future measurements.

  6. Airborne tracking sunphotometer apparatus and system

    NASA Technical Reports Server (NTRS)

    Matsumoto, Yutaka (Inventor); Mina, Cesar (Inventor); Russell, Philip B. (Inventor); Vanark, William B. (Inventor)

    1987-01-01

    An airborne tracking Sun photometer apparatus has a rotatable dome. An azimuth drive motor is connected to rotate the dome. The dome has an equatorial slot. A cylindrical housing is pivotally mounted inside the dome at the equatorial slot. A photometer is mounted in the housing to move in the equatorial slot as the housing pivots. The photometer has an end facing from the slot with an optical flat transparent window. An elevation drive motor is connected to pivot the cylindrical housing. The rotatable dome is mounted in the bulkhead of an aircraft to extend from the interior of the aircraft. A Sun sensor causes the photometer to track the Sun automatically. Alternatively, the photometer may be oriented manually or by computer.

  7. Stabilized optical tracking platform for airborne applications

    NASA Astrophysics Data System (ADS)

    Malueg, Richard; Colella, Nicholas J.; Hakala, Dennis B.

    1995-05-01

    The operations or independent small, lightweight infrared (IR) sensors, called Notifiers and Interrogators, are coordinated to detect and track theater ballistic missiles (TBMs) during boost phase from high altitude aircraft. The Notifier provides early detection of TBM launches over a wide field-of-regard facing the earth. When a target candidate is detected, an Interrogator immediately points at the object to first validate the persistence of the object, to perform TBM authentication, and to determine trajectory coordinates of the TBM. The Notifier and Interrogator sensors differ in their optical trains but otherwise are identical; the later offering nearly 3.5x higher angular resolution and a filter wheel. The sensors must rapidly assess their fields-of-regard to accomplish their roles. A unique three-axis stabilized optical tracking platform has resulted from the requirements thus imposed on angular rates, settling times, and angular stability. The line-of-sight of each earth facing sensor is pointed by a step-and-settle mirror drive that covers a hemisphere field-of-regard including nadir and the horizon. The line-of-sight is steerable through 360 degrees in azimuth and 90 degrees in elevation. This paper describes the 'proof of concept' implementation and it provides details about he designs of critical components that make up the optical tracking platform and the step-and- settle mirror drives.

  8. Detecting tropical forest biomass dynamics from repeated airborne Lidar measurements

    NASA Astrophysics Data System (ADS)

    Meyer, V.; Saatchi, S. S.; Chave, J.; Dalling, J.; Bohlman, S.; Fricker, G. A.; Robinson, C.; Neumann, M.

    2013-02-01

    Reducing uncertainty of terrestrial carbon cycle depends strongly on the accurate estimation of changes of global forest carbon stock. However, this is a challenging problem from either ground surveys or remote sensing techniques in tropical forests. Here, we examine the feasibility of estimating changes of tropical forest biomass from two airborne Lidar measurements acquired about 10 yr apart over Barro Colorado Island (BCI), Panama from high and medium resolution airborne sensors. The estimation is calibrated with the forest inventory data over 50 ha that was surveyed every 5 yr during the study period. We estimated the aboveground forest biomass and its uncertainty for each time period at different spatial scales (0.04, 0.25, 1.0 ha) and developed a linear regression model between four Lidar height metrics and the aboveground biomass. The uncertainty associated with estimating biomass changes from both ground and Lidar data was quantified by propagating measurement and prediction errors across spatial scales. Errors associated with both the mean biomass stock and mean biomass change declined with increasing spatial scales. Biomass changes derived from Lidar and ground estimates were largely (36 out 50 plots) in the same direction at the spatial scale of 1 ha. Lidar estimation of biomass was accurate at the 1 ha scale (R2 = 0.7 and RMSEmean = 28.6 Mg ha-1). However, to predict biomass changes, errors became comparable to ground estimates only at about 10-ha or more. Our results indicate that the 50-ha BCI plot lost a~significant amount of biomass (-0.8 ± 2.2 Mg ha-1 yr-1) over the past decade (2000-2010). Over the entire island and during the same period, mean AGB change is -0.4 ± 3.7 Mg ha-1 yr-1. Old growth forests lost biomass (-0.7 ± 3.5 Mg ha-1 yr-1), whereas the secondary forests gained biomass (+0.4 ± 3.4 Mg ha-1 yr-1). Our analysis demonstrates that repeated Lidar surveys, even with two different sensors, is able to estimate biomass changes in old

  9. Airborne tracking resolution requirements for urban vehicles

    NASA Astrophysics Data System (ADS)

    Robinson, Aaron L.; Miller, Brian; Richardson, Phil; Ra, Chun

    2008-04-01

    This paper details the development, experimentation, collected data and the results of research designed to gain an understanding of the temporal and spatial image collection guidelines for tracking urban vehicles. More specifically, a quantitative understanding of the relationship between human observer performance and the spatial and temporal resolution is sought. Performance is measured as a function of the number of video frames per second, imager spatial resolution and the ability of the observer to accurately determine the destination of a moving vehicle target. The research is restricted to data and imagery collected from altitudes typical of modern low to mid altitude persistent surveillance platforms using a wide field of view. The ability of the human observer to perform an unaided track of the vehicle was determined by their completion of carefully designed perception experiments. In these experiments, the observers were presented with simulated imagery from Night Vision's EOSim urban terrain simulator. The details of the simulated targets and backgrounds, the design of the experiments and their associated results are included in this treatment.

  10. UAVSAR - A New Airborne L-Band Radar for Repeat Pass Interferometry

    NASA Technical Reports Server (NTRS)

    Mace, Thomas H.; Lou, Yunling

    2009-01-01

    NASA/JPL has developed a new airborne Synthetic Aperture Radar (SAR) which has become available for use by the scientific community in January, 2009. Pod mounted, the UAVSAR was designed to be portable among a variety of aircraft, including unmanned aerial systems (UAS). The instrument operates in the L-Band, has a resolution under 2m from a GPS altitude of 12Km and a swath width of approximately 20Km. UAVSAR currently flies on a modified Gulfstream-III aircraft, operated by NASA s Dryden Flight Research Center at Edwards, California. The G-III platform enables repeat-pass interferometric measurements, by using a modified autopilot and precise kinematic differential GPS to repeatedly fly the aircraft within a specified 10m tube. The antenna is electronically steered along track to assure that the antenna beam can be directed independently, regardless of speed and wind direction. The instrument can be controlled remotely, AS AN OPTION, using the Research Environment for Vehicle Embedded Analysis on Linux (REVEAL). This allows simulation of the telepresence environment necessary for flight on UAS. Potential earth science research and applications include surface deformation, volcano studies, ice sheet dynamics, and vegetation structure.

  11. Detecting tropical forest biomass dynamics from repeated airborne lidar measurements

    NASA Astrophysics Data System (ADS)

    Meyer, V.; Saatchi, S. S.; Chave, J.; Dalling, J. W.; Bohlman, S.; Fricker, G. A.; Robinson, C.; Neumann, M.; Hubbell, S.

    2013-08-01

    Reducing uncertainty of terrestrial carbon cycle depends strongly on the accurate estimation of changes of global forest carbon stock. However, this is a challenging problem from either ground surveys or remote sensing techniques in tropical forests. Here, we examine the feasibility of estimating changes of tropical forest biomass from two airborne lidar measurements of forest height acquired about 10 yr apart over Barro Colorado Island (BCI), Panama. We used the forest inventory data from the 50 ha Center for Tropical Forest Science (CTFS) plot collected every 5 yr during the study period to calibrate the estimation. We compared two approaches for detecting changes in forest aboveground biomass (AGB): (1) relating changes in lidar height metrics from two sensors directly to changes in ground-estimated biomass; and (2) estimating biomass from each lidar sensor and then computing changes in biomass from the difference of two biomass estimates, using two models, namely one model based on five relative height metrics and the other based only on mean canopy height (MCH). We performed the analysis at different spatial scales from 0.04 ha to 10 ha. Method (1) had large uncertainty in directly detecting biomass changes at scales smaller than 10 ha, but provided detailed information about changes of forest structure. The magnitude of error associated with both the mean biomass stock and mean biomass change declined with increasing spatial scales. Method (2) was accurate at the 1 ha scale to estimate AGB stocks (R2 = 0.7 and RMSEmean = 27.6 Mg ha-1). However, to predict biomass changes, errors became comparable to ground estimates only at a spatial scale of about 10 ha or more. Biomass changes were in the same direction at the spatial scale of 1 ha in 60 to 64% of the subplots, corresponding to p values of respectively 0.1 and 0.033. Large errors in estimating biomass changes from lidar data resulted from the uncertainty in detecting changes at 1 ha from ground census data

  12. Robust and Rapid Air-Borne Odor Tracking without Casting.

    PubMed

    Bhattacharyya, Urvashi; Bhalla, Upinder Singh

    2015-01-01

    Casting behavior (zigzagging across an odor stream) is common in air/liquid-borne odor tracking in open fields; however, terrestrial odor localization often involves path selection in a familiar environment. To study this, we trained rats to run toward an odor source in a multi-choice olfactory arena with near-laminar airflow. We find that rather than casting, rats run directly toward an odor port, and if this is incorrect, they serially sample other sources. This behavior is consistent and accurate in the presence of perturbations, such as novel odors, background odor, unilateral nostril stitching, and turbulence. We developed a model that predicts that this run-and-scan tracking of air-borne odors is faster than casting, provided there are a small number of targets at known locations. Thus, the combination of best-guess target selection with fallback serial sampling provides a rapid and robust strategy for finding odor sources in familiar surroundings. PMID:26665165

  13. [EFFECT OF REPEATED SPACE FLIGHTS ON OCULAR TRACKING].

    PubMed

    Naumov, I A; Kornilova, L N; Glukhikh, D O; Pavlova, A S; Khabarova, E V; Ekimovsky, G A; Vasin, A V

    2016-01-01

    The paper reports the results of studying the vestibular and ocular intersensory interactions and eye tracking function in 32 cosmonauts on maiden and repeated missions to the International space station. Mission duration ranged from 125 to 215 days. The cosmonauts were tested twice pre launch (baseline data collection) and on days R + 1/2, 4/5 and 8/9. Video oculography was used to test eye movements. It was found that in the majority of cosmonauts who had no experience of long-duration space missions the eye tracking function remained impaired significantly till R + 8/9. In cosmonauts who had already encountered with microgravity, obvious changes in eye tracking were observed on R + 1/2 only and, residual, on R + 4/5. On recovery, a new eye tracking strategy was acquired only by cosmonauts who had the first touch with spaceflight microgravity. PMID:27344853

  14. Inversely tracking indoor airborne particles to locate their release sources

    NASA Astrophysics Data System (ADS)

    Zhang, Tengfei (Tim); Li, Hongzhu; Wang, Shugang

    2012-08-01

    Airborne particles can have numerous adverse effects on human health. Knowing the release locations of airborne particulate sources is helpful in minimizing pollutant exposure. This paper describes a proposal to locate indoor particulate sources by two inverse models: the quasi-reversibility (QR) model and the zone prescription of contaminant sources with the Lagrangian-reversibility (LR) model. The QR model reverses the time marching direction of the Eulerian governing equation and replaces the second-order diffusion term with a fourth-order stabilization term. The zone prescription LR model traces individual particulate motion in a Lagrangian reference frame after reversing the flow field. The particle trajectories are solved backward to the initial release once the conservative forces acting on particles are reversed. The tracked particles are proposed to be placed at the zone boundary of the largest concentration contour within the domain at a given time, which is provided as the initially known information. By connecting all particles at t = 0, a zone is formed that can prescribe the actual contaminant source. This study finds that both models can accurately locate particulate sources released instantaneously at a spot. The QR model performs slightly better than the LR model but is much more computationally demanding.

  15. Detection and tracking of humans from an airborne platform

    NASA Astrophysics Data System (ADS)

    van Eekeren, Adam W. M.; Dijk, Judith; Burghouts, Gertjan

    2014-10-01

    Airborne platforms are recording large amounts of video data. Extracting the events which are needed to see is a time-demanding task for analysts. The reason for this is that the sensors record hours of video data in which only a fraction of the footage contains events of interest. For the analyst, it is hard to retrieve such events from the large amounts of video data by hand. A way to extract information more automatically from the data is to detect all humans within the scene. This can be done in a real-time scenario (both on-board as on the ground station) for strategic and tactical purposes and in an offline scenario where the information is analyzed after recording to acquire intelligence (e.g. a daily life pattern). In this paper, we evaluate three different methods for object detection from a moving airborne platform. The first one is a static person detection algorithm. The main advantage of this method is that it can be used on single frames, and therefor does not depend on the stabilization of the platform. The main disadvantage of this method is that the number of pixels needed for the detection is pretty large. The second method is based on detection of motion-in-motion. Here the background is stabilized, and clusters of pixels that move with respect to this stabilized background are detected as moving object. The main advantage is that all moving objects are detected, the main disadvantage is that it heavily depends on the quality of the stabilization. The third method combines both previous detection methods. The detections are tracked using a histogram-based tracker, so that missed detections can be filled in and a trajectory of all objects can be determined. We demonstrate the tracking performance using the three different detections methods on the publicly available UCF-ARG aerial dataset. The performance is evaluated for two human actions (running and digging) and varying object sizes. It is shown that a combined detection approach (static person

  16. SKYWARD: the next generation airborne infrared search and track

    NASA Astrophysics Data System (ADS)

    Fortunato, L.; Colombi, G.; Ondini, A.; Quaranta, C.; Giunti, C.; Sozzi, B.; Balzarotti, G.

    2016-05-01

    Infrared Search and Track systems are an essential element of the modern and future combat aircrafts. Passive automatic search, detection and tracking functions, are key points for silent operations or jammed tactical scenarios. SKYWARD represents the latest evolution of IRST technology in which high quality electro-optical components, advanced algorithms, efficient hardware and software solutions are harmonically integrated to provide high-end affordable performances. Additionally, the reduction of critical opto-mechanical elements optimises weight and volume and increases the overall reliability. Multiple operative modes dedicated to different situations are available; many options can be selected among multiple or single target tracking, for surveillance or engagement, and imaging, for landing or navigation aid, assuring the maximum system flexibility. The high quality 2D-IR sensor is exploited by multiple parallel processing chains, based on linear and non-linear techniques, to extract the possible targets from background, in different conditions, with false alarm rate control. A widely tested track processor manages a large amount of candidate targets simultaneously and allows discriminating real targets from noise whilst operating with low target to background contrasts. The capability of providing reliable passive range estimation is an additional qualifying element of the system. Particular care has been dedicated to the detector non-uniformities, a possible limiting factor for distant targets detection, as well as to the design of the electro-optics for a harsh airborne environment. The system can be configured for LWIR or MWIR waveband according to the customer operational requirements. An embedded data recorder saves all the necessary images and data for mission debriefing, particularly useful during inflight system integration and tuning.

  17. UAVSAR: Airborne L-band Radar for Repeat Pass Interferometry

    NASA Technical Reports Server (NTRS)

    Moes, Timothy R.

    2009-01-01

    The primary objectives of the UAVSAR Project were to: a) develop a miniaturized polarimetric L-band synthetic aperture radar (SAR) for use on an unmanned aerial vehicle (UAV) or piloted vehicle. b) develop the associated processing algorithms for repeat-pass differential interferometric measurements using a single antenna. c) conduct measurements of geophysical interest, particularly changes of rapidly deforming surfaces such as volcanoes or earthquakes. Two complete systems were developed. Operational Science Missions began on February 18, 2009 ... concurrent development and testing of the radar system continues.

  18. Mapping Slumgullion Landslide in Colorado, USA Using Airborne Repeat-Pass InSAR

    NASA Astrophysics Data System (ADS)

    Lee, H.; Shrestha, R. L.; Carter, W. E.; Glennie, C. L.; Wang, G.; Lu, Z.; Fernandez-Diaz, J. C.; Cao, N.; Zaugg, E.

    2015-12-01

    Interferometric Synthetic Aperture Radar (InSAR) uses two or more SAR images over the same area to determine landscape topography or ground deformation. An interferogram, generated by the phase components of two coherent SAR images, depicts range changes between the radar and the ground resolution elements, and can be used to derive both landscape topography and subtle changes in surface elevation. However, spaceborne repeat-pass interferometry has two main drawbacks: effects due to differences in atmospheric temperature, pressure, and water vapour at two observation times, and loss of coherence due to long spatial and temporal baselines between observations. Airborne repeat-pass interferometry does not suffer from these drawbacks. The atmospheric effect in case of airborne DInSAR becomes negligible due to smaller swath coverage, and the coherence can be maintained by using smaller spatial and temporal baselines. However, the main technical limitation concerning airborne DInSAR is the need of precise motion compensation with an accurate navigation system to correct for the significant phase errors due to typical flight instability from air turbulence. Here, we present results from a pilot study conducted on July 2015 using both X-band and L-band SlimSAR airborne system over the Slumgullion landslide in Colorado in order to (1) acquire the differential interferograms from the airborne platform, (2) understand their source of errors, and (3) pave a way to improve the precision of the derived surface deformation. The landslide movement estimated from airborne DInSAR is also compared with coincident GPS, terrestrial laser scanning (TLS), airborne LiDAR, and spaceborne DInSAR measurements using COSMO-SkyMed images. The airborne DInSAR system has a potential to provide time-transient variability in land surface topography with high-precision and high-resolution, and provide researchers with greater flexibility in selecting the temporal and spatial baselines of the data

  19. AIRBORNE INERTIAL SURVEYING USING LASER TRACKING AND PROFILING TECHNIQUES.

    USGS Publications Warehouse

    Cyran, Edward J.

    1986-01-01

    The U. S. Geological Survey through a contract with the Charles Stark Draper Laboratory has developed the Aerial Profiling of Terrain System. This is an airborne inertial surveying system designed to use a laser tracker to provide position and velocity updates, and a laser profiler to measure terrain elevations. The performance characteristics of the system are discussed with emphasis placed on the performance of the laser devices. The results of testing the system are summarized for both performance evaluation and applications.

  20. Airborne Detection and Tracking of Geologic Leakage Sites

    NASA Astrophysics Data System (ADS)

    Jacob, Jamey; Allamraju, Rakshit; Axelrod, Allan; Brown, Calvin; Chowdhary, Girish; Mitchell, Taylor

    2014-11-01

    Safe storage of CO2 to reduce greenhouse gas emissions without adversely affecting energy use or hindering economic growth requires development of monitoring technology that is capable of validating storage permanence while ensuring the integrity of sequestration operations. Soil gas monitoring has difficulty accurately distinguishing gas flux signals related to leakage from those associated with meteorologically driven changes of soil moisture and temperature. Integrated ground and airborne monitoring systems are being deployed capable of directly detecting CO2 concentration in storage sites. Two complimentary approaches to detecting leaks in the carbon sequestration fields are presented. The first approach focuses on reducing the requisite network communication for fusing individual Gaussian Process (GP) CO2 sensing models into a global GP CO2 model. The GP fusion approach learns how to optimally allocate the static and mobile sensors. The second approach leverages a hierarchical GP-Sigmoidal Gaussian Cox Process for airborne predictive mission planning to optimally reducing the entropy of the global CO2 model. Results from the approaches will be presented.

  1. Long-Term Tracking of a Specific Vehicle Using Airborne Optical Camera Systems

    NASA Astrophysics Data System (ADS)

    Kurz, F.; Rosenbaum, D.; Runge, H.; Cerra, D.; Mattyus, G.; Reinartz, P.

    2016-06-01

    In this paper we present two low cost, airborne sensor systems capable of long-term vehicle tracking. Based on the properties of the sensors, a method for automatic real-time, long-term tracking of individual vehicles is presented. This combines the detection and tracking of the vehicle in low frame rate image sequences and applies the lagged Cell Transmission Model (CTM) to handle longer tracking outages occurring in complex traffic situations, e.g. tunnels. The CTM model uses the traffic conditions in the proximities of the target vehicle and estimates its motion to predict the position where it reappears. The method is validated on an airborne image sequence acquired from a helicopter. Several reference vehicles are tracked within a range of 500m in a complex urban traffic situation. An artificial tracking outage of 240m is simulated, which is handled by the CTM. For this, all the vehicles in the close proximity are automatically detected and tracked to estimate the basic density-flow relations of the CTM model. Finally, the real and simulated trajectories of the reference vehicles in the outage are compared showing good correspondence also in congested traffic situations.

  2. Comparative study of tracking performance in an airborne tracking radar simulator using global positioning system versus monopulse radar techniques

    NASA Astrophysics Data System (ADS)

    Nguyen, Joseph H.; Holley, William D.; Gagnon, Garry

    1993-10-01

    This paper attempts to address the tracking accuracy between the two systems under test. A monopulse radar model was developed to theoretically calculate the would-be measured angle and angle variances. Essentially, measurements of the target's angle, angle variances, range and range rate from the monopulse radar receiver of an aircraft are assessed against the tracking performance of an airborne simulator which uses the time, space, position information (TSPI) delivered from a global positioning system (GPS) system. The accuracy of measurements from a monopulse radar primarily depends on the signal-to-noise ratio (SNR), distance from target in this case, but information received from the GPS Space Vehicle would be virtually jamfree, and independent of distance. Tracking using GPS data however requires good data link between airborne participants. The simulation fidelity becomes an issue when the target is in close range track. The monopulse random slope error and target glint become significant, while the resolution from GPS data links remains the same.

  3. Quantifying landscape change in an arctic coastal lowland using repeat airborne LiDAR

    NASA Astrophysics Data System (ADS)

    Jones, Benjamin M.; Stoker, Jason M.; Gibbs, Ann E.; Grosse, Guido; Romanovsky, Vladimir E.; Douglas, Thomas A.; Kinsman, Nicole E. M.; Richmond, Bruce M.

    2013-12-01

    Increases in air, permafrost, and sea surface temperature, loss of sea ice, the potential for increased wave energy, and higher river discharge may all be interacting to escalate erosion of arctic coastal lowland landscapes. Here we use airborne light detection and ranging (LiDAR) data acquired in 2006 and 2010 to detect landscape change in a 100 km2 study area on the Beaufort Sea coastal plain of northern Alaska. We detected statistically significant change (99% confidence interval), defined as contiguous areas (>10 m2) that had changed in height by at least 0.55 m, in 0.3% of the study region. Erosional features indicative of ice-rich permafrost degradation were associated with ice-bonded coastal, river, and lake bluffs, frost mounds, ice wedges, and thermo-erosional gullies. These features accounted for about half of the area where vertical change was detected. Inferred thermo-denudation and thermo-abrasion of coastal and river bluffs likely accounted for the dominant permafrost-related degradational processes with respect to area (42%) and volume (51%). More than 300 thermokarst pits significantly subsided during the study period, likely as a result of storm surge flooding of low-lying tundra (<1.4 m asl) as well as the lasting impact of warm summers in the late-1980s and mid-1990s. Our results indicate that repeat airborne LiDAR can be used to detect landscape change in arctic coastal lowland regions at large spatial scales over sub-decadal time periods.

  4. Clutter effects on airborne tracking resolution requirements for urban vehicles

    NASA Astrophysics Data System (ADS)

    Robinson, Aaron L.; Miller, Brian; Richardson, Phillip; Ra, Chun

    2010-04-01

    This paper details the development, experimentation, collected data and the results of research designed to gain an understanding of the effects of clutter on the temporal and spatial image collection guidelines for tracking urban vehicles. More specifically, a quantitative understanding of the relationship between human observer performance and the spatial and temporal resolution is sought. Performance is measured as a function of the number of video frames per second, imager spatial resolution and the ability of the observer to accurately determine the destination of a moving vehicle target as it encounters vehicles with similar infrared signatures. The research is restricted to data and imagery collected from altitudes typical of modern low to mid altitude persistent surveillance platforms using a wide field of view. The ability of the human observer to perform an unaided track of the vehicle was determined by their completion of carefully designed perception experiments. In these experiments, the observers were presented with simulated imagery from Night Vision's EOSim urban terrain simulator. The details of the simulated targets and backgrounds, the design of the experiments and their associated results are included in this treatment.

  5. Determining Firn Compaction Rates Using Repeat-Track Radar Surveys in West Antarctica and Greenland

    NASA Astrophysics Data System (ADS)

    Medley, B.; Ligtenberg, S.; Kuipers Munneke, P.; Joughin, I. R.; van den Broeke, M. R.; Gogineni, S.; Nowicki, S.

    2014-12-01

    Measurements of surface elevation change must be properly partitioned between thickness changes from firn versus ice processes to determine the actual mass change because of the density difference between firn and ice. While ice dynamics controls changes in the ice column, fluctuations in both the snow accumulation and firn compaction rates result in variations in the firn column thickness. Several recent studies using both ground-based and airborne radar have greatly improved our understanding of the spatiotemporal variations in the accumulation rate. On the other hand, because of the difficulty in measuring firn compaction rates, the number of measurements remains quite low and the coverage is very sparse. Here, we present measurements of the firn compaction rate using the Center for Remote Sensing of Ice Sheets snow radar data from NASA's Operation IceBridge repeat-track surveys. To measure firn compaction rates from the aerial survey we first measure the depths to various horizons in the firn column. In the subsequent survey, we measure the depths to the same firn horizons but must remove the additional thickness from accumulated snow. To account for the additional accumulation, we measure the thickness to the buried horizon that represents the surface from the first survey. The change in thickness between the initial surface and the radar horizons provides total compaction and when divided by the time interval between surveys, provides the compaction rate.Specifically, we measure the spatiotemporal variations in the firn compaction rate in the Thwaites Glacier catchment area between 2009 and 2011. In addition, we present newly derived compaction rates from the dry-snow zone of Greenland. We also discuss the limitations of the method resulting from (1) the vertical resolution of the radar system, (2) colocation errors, (3) the dependence of radar wave speed on firn density, which varies in both space and time, and (4) measuring to a horizon of constant age

  6. Recent accumulation rates of an Alpine glacier derived from repeated airborne GPR and firn cores

    NASA Astrophysics Data System (ADS)

    Sold, Leo; Huss, Matthias; Eichler, Anja; Schwikowski, Margit; Hoelzle, Martin

    2014-05-01

    The topmost areas of glaciers contain a valuable record of their past accumulation rates. The water equivalent of annual firn layers can be used to initiate or extend existing time series of local mass balance and, ultimately, to consolidate the knowledge on the response of glaciers to changing climatic conditions. Measurements of the thickness and density of firn layers typically involve drilling in remote areas and core analysis and are thus expensive in terms of time and effort. Here, we discuss measurements from 2012 on Findelengletscher, Switzerland, a large Alpine valley glacier, using two in-situ firn cores and airborne Ground-Penetrating Radar (GPR). The firn cores were analysed regarding their density, major ions and deuterium concentration. The ammonium (NH4+) concentration is known to show seasonality due to a higher source activity and pronounced vertical transportation in the atmosphere in summer. The deuterium concentration serves as a proxy for air temperature during precipitation formation. Together, they provide depth and dating of annual summer surfaces. GPR has previously been used for a non-destructive assessment of internal layers in snow, firn and ice. Signal reflections indicate changes in the dielectric properties of the material, e.g. density changes at former summer surfaces. Airborne surveys allow measurements to be taken in remote and inaccessible areas. However, to transfer information from the GPR pulse travel time to the depth domain, the dielectric permittivity of the material is required, that changes with density of the firn. We observed a good agreement of the GPR signal with pronounced changes in the density profile, ice layers and peak contents of major ions. This underlines the high potential of GPR for detecting firn layers. However, not all peak-densities and thick ice layers represent a former glacier summer surface but can also be due to melting and refreezing during winter. We show that up to four years of annual

  7. Tracking neural correlates of successful learning over repeated sequence observations.

    PubMed

    Steinemann, Natalie A; Moisello, Clara; Ghilardi, M Felice; Kelly, Simon P

    2016-08-15

    The neural correlates of memory formation in humans have long been investigated by exposing subjects to diverse material and comparing responses to items later remembered to those forgotten. Tasks requiring memorization of sensory sequences afford unique possibilities for linking neural memorization processes to behavior, because, rather than comparing across different items of varying content, each individual item can be examined across the successive learning states of being initially unknown, newly learned, and eventually, fully known. Sequence learning paradigms have not yet been exploited in this way, however. Here, we analyze the event-related potentials of subjects attempting to memorize sequences of visual locations over several blocks of repeated observation, with respect to pre- and post-block recall tests. Over centro-parietal regions, we observed a rapid P300 component superimposed on a broader positivity, which exhibited distinct modulations across learning states that were replicated in two separate experiments. Consistent with its well-known encoding of surprise, the P300 deflection monotonically decreased over blocks as locations became better learned and hence more expected. In contrast, the broader positivity was especially elevated at the point when a given item was newly learned, i.e., started being successfully recalled. These results implicate the Broad Positivity in endogenously-driven, intentional memory formation, whereas the P300, in processing the current stimulus to the degree that it was previously uncertain, indexes the cumulative knowledge thereby gained. The decreasing surprise/P300 effect significantly predicted learning success both across blocks and across subjects. This presents a new, neural-based means to evaluate learning capabilities independent of verbal reports, which could have considerable value in distinguishing genuine learning disabilities from difficulties to communicate the outcomes of learning, or perceptual

  8. Control design for image tracking with an inertially stabilized airborne camera platform

    NASA Astrophysics Data System (ADS)

    Hurák, Zdenek; Rezáč, Martin

    2010-04-01

    The paper reports on a few control engineering issues related to design and implementation of an image-based pointing and tracking system for an inertially stabilized airborne camera platform. A medium-sized platform has been developed by the authors and a few more team members within a joint governmental project coordinated by Czech Air Force Research Institute. The resulting experimental platform is based on a common double gimbal configuration with two direct drive motors and off-the-shelf MEMS gyros. Automatic vision-based tracking system is built on top of the inertial stabilization. Choice of a suitable control configuration is discussed first, because the decoupled structure for the inner inertial rate controllers does not extend easily to the outer imagebased pointing and tracking loop. It appears that the pointing and tracking controller can benefit much from availability of measurements of an inertial rate of the camera around its optical axis. The proposed pointing and tracking controller relies on feedback linearization well known in image-based visual servoing. Simple compensation of a one sample delay introduced into the (slow) visual pointing and tracking loop by the computer vision system is proposed. It relies on a simple modification of the well-known Smith predictor scheme where the prediction takes advantage of availability of the (fast and undelayed) inertial rate measurements.

  9. Design of an Airborne L-Band Cross-Track Scanning Scatterometer

    NASA Technical Reports Server (NTRS)

    Hilliard, Lawrence M. (Technical Monitor)

    2002-01-01

    In this report, we describe the design of an airborne L-band cross-track scanning scatterometer suitable for airborne operation aboard the NASA P-3 aircraft. The scatterometer is being designed for joint operation with existing L-band radiometers developed by NASA for soil moisture and ocean salinity remote sensing. In addition, design tradeoffs for a space-based radar system have been considered, with particular attention given to antenna architectures suitable for sharing the antenna between the radar and radiometer. During this study, we investigated a number of imaging techniques, including the use of real and synthetic aperture processing in both the along track and cross-track dimensions. The architecture selected will permit a variety of beamforming algorithms to be implemented, although real aperture processing, with hardware beamforming, provides better sidelobe suppression than synthetic array processing and superior signal-to-noise performance. In our discussions with the staff of NASA GSFC, we arrived at an architecture that employs complete transmit/receive modules for each subarray. Amplitude and phase control at each of the transmit modules will allow a low-sidelobe transmit pattern to be generated over scan angles of +/- 50 degrees. Each receiver module will include all electronics necessary to downconvert the received signal to an IF offset of 30 MHz where it will be digitized for further processing.

  10. Vehicle tracking in wide area motion imagery from an airborne platform

    NASA Astrophysics Data System (ADS)

    van Eekeren, Adam W. M.; van Huis, Jasper R.; Eendebak, Pieter T.; Baan, Jan

    2015-10-01

    Airborne platforms, such as UAV's, with Wide Area Motion Imagery (WAMI) sensors can cover multiple square kilometers and produce large amounts of video data. Analyzing all data for information need purposes becomes increasingly labor-intensive for an image analyst. Furthermore, the capacity of the datalink in operational areas may be inadequate to transfer all data to the ground station. Automatic detection and tracking of people and vehicles enables to send only the most relevant footage to the ground station and assists the image analysts in effective data searches. In this paper, we propose a method for detecting and tracking vehicles in high-resolution WAMI images from a moving airborne platform. For the vehicle detection we use a cascaded set of classifiers, using an Adaboost training algorithm on Haar features. This detector works on individual images and therefore does not depend on image motion stabilization. For the vehicle tracking we use a local template matching algorithm. This approach has two advantages. In the first place, it does not depend on image motion stabilization and it counters the inaccuracy of the GPS data that is embedded in the video data. In the second place, it can find matches when the vehicle detector would miss a certain detection. This results in long tracks even when the imagery is of low frame-rate. In order to minimize false detections, we also integrate height information from a 3D reconstruction that is created from the same images. By using the locations of buildings and roads, we are able to filter out false detections and increase the performance of the tracker. In this paper we show that the vehicle tracks can also be used to detect more complex events, such as traffic jams and fast moving vehicles. This enables the image analyst to do a faster and more effective search of the data.

  11. Robust and Rapid Air-Borne Odor Tracking without Casting1,2,3

    PubMed Central

    Bhattacharyya, Urvashi

    2015-01-01

    Abstract Casting behavior (zigzagging across an odor stream) is common in air/liquid-borne odor tracking in open fields; however, terrestrial odor localization often involves path selection in a familiar environment. To study this, we trained rats to run toward an odor source in a multi-choice olfactory arena with near-laminar airflow. We find that rather than casting, rats run directly toward an odor port, and if this is incorrect, they serially sample other sources. This behavior is consistent and accurate in the presence of perturbations, such as novel odors, background odor, unilateral nostril stitching, and turbulence. We developed a model that predicts that this run-and-scan tracking of air-borne odors is faster than casting, provided there are a small number of targets at known locations. Thus, the combination of best-guess target selection with fallback serial sampling provides a rapid and robust strategy for finding odor sources in familiar surroundings. PMID:26665165

  12. Eccentricity and argument of perigee control for orbits with repeat ground tracks

    NASA Technical Reports Server (NTRS)

    Vincent, Mark A.

    1992-01-01

    In order to gain an understanding into the problem of eccentricity (e) and argument of perigee (omega) control for TOPEX/Poseidon, the two cases where the highest latitude crossing time and one of the equator crossings are held constant are investigated. Variations in e and omega cause a significant effect on the satellite's ground-track repeatability. Maintaining e and omega near their frozen values will minimize this variation. Analytical expressions are found to express this relationship while keeping an arbitrary point of the ground track fixed. The initial offset of the ground track from its nominal path determines the subsequent evolution of e and omega about their frozen values. This long-term behavior is numerically determined using an earth gravitational field including the first 17 zonal harmonics. The numerical results are plotted together with the analytical constraints to see if the later values of e and omega cause unacceptable deviation in the ground track.

  13. Extracting Tree Height from Repeat-Pass PolInSAR Data : Experiments with JPL and ESA Airborne Systems

    NASA Technical Reports Server (NTRS)

    Lavalle, Marco; Ahmed, Razi; Neumann, Maxim; Hensley, Scott

    2013-01-01

    In this paper we present our latest developments and experiments with the random-motion-over-ground (RMoG) model used to extract canopy height and other important forest parameters from repeat-pass polarimetricinterferometric SAR (Pol-InSAR) data. More specifically, we summarize the key features of the RMoG model in contrast with the random-volume-over-ground (RVoG) model, describe in detail a possible inversion scheme for the RMoG model and illustrate the results of the RMoG inversion using airborne data collected by the Jet Propulsion Laboratory (JPL) and the European Space Agency (ESA).

  14. Repeat Tracking of Individual Songbirds Reveals Consistent Migration Timing but Flexibility in Route

    PubMed Central

    Fraser, Kevin C.; McKinnon, Emily A.; Stutchbury, Bridget J. M.

    2012-01-01

    Tracking repeat migratory journeys of individual animals is required to assess phenotypic plasticity of individual migration behaviour in space and time. We used light-level geolocators to track the long-distance journeys of migratory songbirds (wood thrush, Hylocichla mustelina), and, for the first time, repeat journeys of individuals. We compare between- and within-individual variation in migration to examine flexibility of timing and route in spring and autumn. Date of departure from wintering sites in Central America, along with sex and age factors, explained most of the variation (71%) in arrival date at North American breeding sites. Spring migration showed high within-individual repeatability in timing, but not in route. In particular, spring departure dates of individuals were highly repeatable, with a mean difference between years of just 3 days. Autumn migration timing and routes were not repeatable. Our results provide novel evidence of low phenotypic plasticity in timing of spring migration, which may limit the ability of individuals to adjust migration schedules in response to climate change. PMID:22848395

  15. Kalman Filter Based Feature Analysis for Tracking People from Airborne Images

    NASA Astrophysics Data System (ADS)

    Sirmacek, B.; Reinartz, P.

    2011-09-01

    Recently, analysis of man events in real-time using computer vision techniques became a very important research field. Especially, understanding motion of people can be helpful to prevent unpleasant conditions. Understanding behavioral dynamics of people can also help to estimate future states of underground passages, shopping center like public entrances, or streets. In order to bring an automated solution to this problem, we propose a novel approach using airborne image sequences. Although airborne image resolutions are not enough to see each person in detail, we can still notice a change of color components in the place where a person exists. Therefore, we propose a color feature detection based probabilistic framework in order to detect people automatically. Extracted local features behave as observations of the probability density function (pdf) of the people locations to be estimated. Using an adaptive kernel density estimation method, we estimate the corresponding pdf. First, we use estimated pdf to detect boundaries of dense crowds. After that, using background information of dense crowds and previously extracted local features, we detect other people in non-crowd regions automatically for each image in the sequence. We benefit from Kalman filtering to track motion of detected people. To test our algorithm, we use a stadium entrance image data set taken from airborne camera system. Our experimental results indicate possible usage of the algorithm in real-life man events. We believe that the proposed approach can also provide crucial information to police departments and crisis management teams to achieve more detailed observations of people in large open area events to prevent possible accidents or unpleasant conditions.

  16. Visual real-time detection, recognition and tracking of ground and airborne targets

    NASA Astrophysics Data System (ADS)

    Kovács, Levente; Benedek, Csaba

    2011-03-01

    This paper presents methods and algorithms for real-time visual target detection, recognition and tracking, both in the case of ground-based objects (surveyed from a moving airborne imaging sensor) and flying targets (observed from a ground-based or vehicle mounted sensor). The methods are highly parallelized and partially implemented on GPU, with the goal of real-time speeds even in the case of multiple target observations. Real-time applicability is in focus. The methods use single camera observations, providing a passive and expendable alternative for expensive and/or active sensors. Use cases involve perimeter defense and surveillance situations, where passive detection and observation is a priority (e.g. aerial surveillance of a compound, detection of reconnaissance drones, etc.).

  17. Characteristics of Bayesian multiple model adaptive estimation for tracking airborne targets

    NASA Astrophysics Data System (ADS)

    Netzer, A. S.

    1985-12-01

    Previous studies at the Air Force Institute of Technology have led to the development of a multiple model adaptive filter (MMAF) tracking algorithm which provides significant improvements in tracker performance against highly-dynamic airborne targets over the currently used correlation trackers. A forward looking infra-red (FLIR) sensor is used to provide a target shape function to the tracking algorithm in the form of an 8 x 8 array of intensities projected onto a field of view (FOV). This target image measurement is correlated with an estimate of the target image template, to produce linear offset pseudo-measurements from the center of the FOV, which are provided as measurements to a bank of linear Kalman filters, in the multiple model adaptive filtering (MMAF) structure. The output of the MMAF provides the state estimates used in pointing the FLIR sensor, and generating the new target image estimate. This study investigates the characteristics of this algorithm in order to evaluate its performance against various target scenarios.

  18. An airborne jet train that flies on a soft porous track

    NASA Astrophysics Data System (ADS)

    Mirbod, Parisa; Andreopoulos, Yiannis; Weinbaum, Sheldon

    2008-11-01

    This paper explores the quantitative feasibility of developing an airborne jet train that flies on a soft porous track within centimeters of the earth's surface at speeds approaching current commercial jet aircraft. The jet train employs a lift mechanism first proposed in Feng & Weinbaum (2000) J. Fluid Mech. 422:282 and a nearly frictionless track suggested in Wu et al. (2004) Phys. Rev. Lett. 93(19):194501. Using an asymptotic analysis for large values of the permeability parameter H/Kp, where H is the porous layer thickness and Kp the Darcy permeability, we first show that it is possible to support a 70 metric ton jet train carrying 200 passengers on a confined porous material if its Kp is approximately 5 x 10-9 m^2. For this Kp one finds that the tilt of the planform is < 0.1 degrees and the lift-off velocity is < 5 m/s. Compression tests on a fiber-fill material with these properties show that the fibers contribute < 0.2 percent of the total lift and hence the friction force of the fiber phase is negligible. Using jet engines of 10,000 lbf thrust, about 1/5 that of a 200 passenger jet aircraft, one is able to obtain a cruising velocity approaching 700 km/hr. This would allow for huge fuel savings, especially on short flights where much of the energy is used to climb to altitude and overcoming lift induced drag.

  19. Validation of a track repeating algorithm for intensity modulated proton therapy: clinical cases study

    NASA Astrophysics Data System (ADS)

    Yepes, Pablo P.; Eley, John G.; Liu, Amy; Mirkovic, Dragan; Randeniya, Sharmalee; Titt, Uwe; Mohan, Radhe

    2016-04-01

    Monte Carlo (MC) methods are acknowledged as the most accurate technique to calculate dose distributions. However, due its lengthy calculation times, they are difficult to utilize in the clinic or for large retrospective studies. Track-repeating algorithms, based on MC-generated particle track data in water, accelerate dose calculations substantially, while essentially preserving the accuracy of MC. In this study, we present the validation of an efficient dose calculation algorithm for intensity modulated proton therapy, the fast dose calculator (FDC), based on a track-repeating technique. We validated the FDC algorithm for 23 patients, which included 7 brain, 6 head-and-neck, 5 lung, 1 spine, 1 pelvis and 3 prostate cases. For validation, we compared FDC-generated dose distributions with those from a full-fledged Monte Carlo based on GEANT4 (G4). We compared dose-volume-histograms, 3D-gamma-indices and analyzed a series of dosimetric indices. More than 99% of the voxels in the voxelized phantoms describing the patients have a gamma-index smaller than unity for the 2%/2 mm criteria. In addition the difference relative to the prescribed dose between the dosimetric indices calculated with FDC and G4 is less than 1%. FDC reduces the calculation times from 5 ms per proton to around 5 μs.

  20. Validation of a track repeating algorithm for intensity modulated proton therapy: clinical cases study.

    PubMed

    Yepes, Pablo P; Eley, John G; Liu, Amy; Mirkovic, Dragan; Randeniya, Sharmalee; Titt, Uwe; Mohan, Radhe

    2016-04-01

    Monte Carlo (MC) methods are acknowledged as the most accurate technique to calculate dose distributions. However, due its lengthy calculation times, they are difficult to utilize in the clinic or for large retrospective studies. Track-repeating algorithms, based on MC-generated particle track data in water, accelerate dose calculations substantially, while essentially preserving the accuracy of MC. In this study, we present the validation of an efficient dose calculation algorithm for intensity modulated proton therapy, the fast dose calculator (FDC), based on a track-repeating technique. We validated the FDC algorithm for 23 patients, which included 7 brain, 6 head-and-neck, 5 lung, 1 spine, 1 pelvis and 3 prostate cases. For validation, we compared FDC-generated dose distributions with those from a full-fledged Monte Carlo based on GEANT4 (G4). We compared dose-volume-histograms, 3D-gamma-indices and analyzed a series of dosimetric indices. More than 99% of the voxels in the voxelized phantoms describing the patients have a gamma-index smaller than unity for the 2%/2 mm criteria. In addition the difference relative to the prescribed dose between the dosimetric indices calculated with FDC and G4 is less than 1%. FDC reduces the calculation times from 5 ms per proton to around 5 μs. PMID:26961764

  1. The inclusion of higher degree and order gravity terms in the design of a repeat ground track orbit

    NASA Technical Reports Server (NTRS)

    Vincent, Mark A.

    1990-01-01

    Mean Orbit Elements can be chosen such that a desired ground track repeat criteria is obtained when propagating with the secular effects of a central body gravity field. If the proper initial conditions are chosen that correspond to these Mean Elements, the orbit can also be propagated with the full gravity field and form another ground track repeat pattern. Further, if the effects of other perturbative forces are compensated for, such that the ground track remains near this pattern, the central body effects can again be considered repetitive. The process of arriving at these conclusions, along with the supporting numerical simulations, are presented.

  2. Enhanced tracking of airborne targets using a correlator-Kalman filter

    NASA Astrophysics Data System (ADS)

    Millner, P. P.

    1982-12-01

    Over the past four years considerable work has been accomplished at the Air Force Institute of Technology to improve the tracking capability of the high energy laser weapon against airborne targets. In this research, many of the prior concepts are incorporated into a correlator/Kalman filter to develop a tracker capable of providing precise target position estimates in a dynamic shortrange environment using a Forward Looking Infrared sensor (FLIR) to provide measurement data. Digital signal processing in employed on the FLIR data to identify the underlying target intensity shape function when the target under consideration has either single or multiple hot spots. The estimated target shape function is then used as the template in a correlation algorithm, where spatial and frequency domain correlation techniques were explored, to determine the offsets between the template and the incoming measurement. These offsets are used as pseudomeasurements in a linear Kalman filter which exploits knowledge of the process dynamics and statistical knowledge of the correlator error to enhance the position estimates.

  3. Combining airborne electromagnetic and geotechnical data for automated depth to bedrock tracking

    NASA Astrophysics Data System (ADS)

    Christensen, Craig William; Pfaffhuber, Andreas Aspmo; Anschütz, Helgard; Smaavik, Tone Fallan

    2015-08-01

    Airborne electromagnetic (AEM) survey data was used to supplement geotechnical investigations for a highway construction project in Norway. Heterogeneous geology throughout the survey and consequent variable bedrock threshold resistivity hindered efforts to directly track depth to bedrock, motivating us to develop an automated algorithm to extract depth to bedrock by combining both boreholes and AEM data. We developed two variations of this algorithm: one using simple Gaussian or inverse distance weighting interpolators, and another using ordinary kriging and combined probability distribution functions of input parameters. Evaluation shows that for preliminary surveys, significant savings in boreholes required can be made without sacrificing bedrock model accuracy. In the case study presented, we estimate data collection savings of 1000 to 10,000 NOK/km (c. 160 to 1600 USD/km) would have been possible for early phases of the investigation. However, issues with anthropogenic noise, low signal, and uncertainties in the inversion model likely reduced the comparative advantage that including AEM provided. AEM cannot supersede direct sampling where the model accuracy required exceed the resolution possible with the geophysical measurements. Nevertheless, with the algorithm we can identify high probability zones for shallow bedrock, identify steep or anomalous bedrock topography, and estimate the spatial variability of depth at earlier phases of investigation. Thus, we assert that our method is still useful where detailed mapping is the goal because it allows for more efficient planning of secondary phases of drilling.

  4. Antarctic Firn Compaction Rates from Repeat-Track Airborne Radar Data: I. Methods

    NASA Technical Reports Server (NTRS)

    Medley, B.; Ligtenberg, S. R. M.; Joughin, I.; Van Den Broeke, M. R.; Gogineni, S.; Nowicki, S.

    2015-01-01

    While measurements of ice-sheet surface elevation change are increasingly used to assess mass change, the processes that control the elevation fluctuations not related to ice-flow dynamics (e.g. firn compaction and accumulation) remain difficult to measure. Here we use radar data from the Thwaites Glacier (West Antarctica) catchment to measure the rate of thickness change between horizons of constant age over different time intervals: 2009-10, 2010-11 and 2009-11. The average compaction rate to approximately 25m depth is 0.33ma(exp -1), with largest compaction rates near the surface. Our measurements indicate that the accumulation rate controls much of the spatio-temporal variations in the compaction rate while the role of temperature is unclear due to a lack of measurements. Based on a semi-empirical, steady-state densification model, we find that surveying older firn horizons minimizes the potential bias resulting from the variable depth of the constant age horizon. Our results suggest that the spatiotemporal variations in the firn compaction rate are an important consideration when converting surface elevation change to ice mass change. Compaction rates varied by up to 0.12ma(exp -1) over distances less than 6km and were on average greater than 20% larger during the 2010-11 interval than during 2009-10.

  5. Dynamics and internal structure of an Alaskan debris-covered glacier from repeat airborne photogrammetry and surface geophysics

    NASA Astrophysics Data System (ADS)

    Holt, John; Levy, Joseph; Petersen, Eric; Larsen, Chris; Fahnestock, Mark

    2016-04-01

    Debris-covered glaciers and rock glaciers encompass a range of compositions and activity, and can be useful paleoclimate indicators. They also respond differently to ongoing climate change than glaciers without a protective cover. Their flow dynamics are not well understood, and their unique surface morphologies, including lobate fronts and arcuate ridges, likely result from viscous flow influenced by a combination of composition, structure, and climatic factors. However, basic connections between flow kinematics and surface morphology have not yet been established, limiting our ability to understand these features. In order to begin to address this problem we have undertaken airborne and surface studies of multiple debris-covered glaciers in Alaska and the western U.S. Sourdough Rock Glacier in the St. Elias Mountains, Alaska, is completely debris-covered and exhibits numerous transverse compressional ridges. Its trunk also exhibits highly regular bumps and swales with a wavelength of ~175 m and amplitudes up to 12 m. In the middle trunk, lineations (boulder trains and furrows) bend around a point roughly 200m from the eastern edge. We acquired five high-resolution airborne surveys of Sourdough Rock Glacier between late 2013 and late 2015 using lidar and photogrammetry to assess annual and seasonal change at the sub-meter level. Differencing the DTMs provides vertical change while feature tracking in orthophotos provide horizontal velocities that indicate meters of annual motion. The flow field is highly correlated with surface features; in particular, compressional ridges in the lower lobe. Stranded, formerly active lobes are also apparent. Surface geophysical studies were undertaken to constrain internal structure and composition using a combination of ground-penetrating radar (GPR) at 50 and 100 MHz in six transects, and time-domain electromagnetic (TDEM) measurements at 47 locations, primarily in an along-flow transect and two cross-flow transects. We infer

  6. Situational awareness sensor management of space-based EO/IR and airborne GMTI radar for road targets tracking

    NASA Astrophysics Data System (ADS)

    El-Fallah, A.; Zatezalo, A.; Mahler, R.; Mehra, R. K.; Pham, K.

    2010-04-01

    Dynamic sensor management of heterogeneous and distributed sensors presents a daunting theoretical and practical challenge. We present a Situational Awareness Sensor Management (SA-SM) algorithm for the tracking of ground targets moving on a road map. It is based on the previously developed information-theoretic Posterior Expected Number of Targets of Interest (PENTI) objective function, and utilizes combined measurements form an airborne GMTI radar, and a space-based EO/IR sensor. The resulting filtering methods and techniques are tested and evaluated. Different scan rates for the GMTI radar and the EO/IR sensor are evaluated and compared.

  7. Landslide Investigation by Repeat Airborne LiDAR and Ground Monitoring in the Western Suburb of Sapporo, Japan

    NASA Astrophysics Data System (ADS)

    Kasai, M.; Marutani, T.; Yoshida, H.

    2014-12-01

    This study presents landslide investigation using the combination of airborne LiDAR and ground monitoring data. The study site is located on the Teine Landslide (width: 2 km, Length: 6.5 km) in the western suburb of Sapporo city in Hokkaido Island, Japan, which collapsed more than 50,000 years ago. Since then streams have been developing and incising the landslide mass consisted of rock debris and volcanic deposits, presently causing a series of small deep-seated landslides along the banks. Because Sapporo is the economic center of Hokkaido and the suburb is expanding at the toe of the Teine slide, it is important to understand the behaviors of these active slopes to protect residents and infrastructures from unexpected disasters possibly triggered by an intense storm or earthquake. The LiDAR data for the area was first obtained by a manned helicopter in August 2010, and another survey by an unmanned helicopter is planned in autumn 2014 to estimate their activities from changes in the ground surfaces during the period from 2010 to 2014. Ground water level and landslide mass movements have also been monitored on site by using the coring holes for sampling since 2013. The combination of the data sets can make up the deficits of these methods, e.g., errors created through data processing for LiDAR survey and spatially limited information for ground monitoring, enabling to provide a solid three dimensional view of the slope movements. The notion obtained can be utilized to predict their future behaviors as well as to discover active but hiding landslides nearby. This study also showed that repeat monitoring of sites is a way of utilizing UAVs, particularly in terms of cost and convenience.

  8. Repeat Ground Track Lunar Orbits in the Full-Potential Plus Third-Body Problem

    NASA Technical Reports Server (NTRS)

    Russell, Ryan P.; Lara, Martin

    2006-01-01

    A high degree and order Lunar gravitational field is superimposed on the Earth-Moon Restricted Three Body model to capture the dominating forces on a spacecraft in the vicinity of the Moon. For the synchronously rotating Moon, periodic orbits in this model map repeat ground tracks and represent higher order solutions to the frozen orbit problem. The near-circular, stable or near-stable solutions are found over a wide range of defining characteristics making them suitable for long-lifetime parking applications such as science orbits, crew exploration vehicle parking orbits, and global coverage constellation orbits. A full ephemeris is considered for selected orbits to evaluate the validity of the time-invariant, simplified model. Of the most promising results are the low-altitude families of near-circular, inclined orbits that maintain long-term stability despite the highly non-spherical Lunar gravity. The method is systematic and enables rapid design and analysis of long-life orbits around any tidally-locked celestial body with an arbitrarily high degree and order spherical harmonic gravity field. .

  9. PITBUL: a physics-based modeling package for imaging and tracking of airborne targets for HEL applications including active illumination

    NASA Astrophysics Data System (ADS)

    Van Zandt, Noah R.; McCrae, Jack E.; Fiorino, Steven T.

    2013-05-01

    Aimpoint acquisition and maintenance is critical to high energy laser (HEL) system performance. This study demonstrates the development by the AFIT/CDE of a physics-based modeling package, PITBUL, for tracking airborne targets for HEL applications, including atmospheric and sensor effects and active illumination, which is a focus of this work. High-resolution simulated imagery of the 3D airborne target in-flight as seen from the laser position is generated using the HELSEEM model, and includes solar illumination, laser illumination, and thermal emission. Both CW and pulsed laser illumination are modeled, including the effects of illuminator scintillation, atmospheric backscatter, and speckle, which are treated at a first-principles level. Realistic vertical profiles of molecular and aerosol absorption and scattering, as well as optical turbulence, are generated using AFIT/CDE's Laser Environmental Effects Definition and Reference (LEEDR) model. The spatially and temporally varying effects of turbulence are calculated and applied via a fast-running wave optical method known as light tunneling. Sensor effects, for example blur, sampling, read-out noise, and random photon arrival, are applied to the imagery. Track algorithms, including centroid and Fitts correlation, as a part of a closed loop tracker are applied to the degraded imagery and scored, to provide an estimate of overall system performance. To gauge performance of a laser system against a UAV target, tracking results are presented as a function of signal to noise ratio. Additionally, validation efforts to date involving comparisons between simulated and experimental tracking of UAVs are presented.

  10. A Novel Azimuth Super-Resolution Method by Synthesizing Azimuth Bandwidth of Multiple Tracks of Airborne Stripmap SAR Data

    PubMed Central

    Wang, Yan; Li, Jingwen; Sun, Bing; Yang, Jian

    2016-01-01

    Azimuth resolution of airborne stripmap synthetic aperture radar (SAR) is restricted by the azimuth antenna size. Conventionally, a higher azimuth resolution should be achieved by employing alternate modes that steer the beam in azimuth to enlarge the synthetic antenna aperture. However, if a data set of a certain region, consisting of multiple tracks of airborne stripmap SAR data, is available, the azimuth resolution of specific small region of interest (ROI) can be conveniently improved by a novel azimuth super-resolution method as introduced by this paper. The proposed azimuth super-resolution method synthesize the azimuth bandwidth of the data selected from multiple discontinuous tracks and contributes to a magnifier-like function with which the ROI can be further zoomed in with a higher azimuth resolution than that of the original stripmap images. Detailed derivation of the azimuth super-resolution method, including the steps of two-dimensional dechirping, residual video phase (RVP) removal, data stitching and data correction, is provided. The restrictions of the proposed method are also discussed. Lastly, the presented approach is evaluated via both the single- and multi-target computer simulations. PMID:27304959

  11. A Novel Azimuth Super-Resolution Method by Synthesizing Azimuth Bandwidth of Multiple Tracks of Airborne Stripmap SAR Data.

    PubMed

    Wang, Yan; Li, Jingwen; Sun, Bing; Yang, Jian

    2016-01-01

    Azimuth resolution of airborne stripmap synthetic aperture radar (SAR) is restricted by the azimuth antenna size. Conventionally, a higher azimuth resolution should be achieved by employing alternate modes that steer the beam in azimuth to enlarge the synthetic antenna aperture. However, if a data set of a certain region, consisting of multiple tracks of airborne stripmap SAR data, is available, the azimuth resolution of specific small region of interest (ROI) can be conveniently improved by a novel azimuth super-resolution method as introduced by this paper. The proposed azimuth super-resolution method synthesize the azimuth bandwidth of the data selected from multiple discontinuous tracks and contributes to a magnifier-like function with which the ROI can be further zoomed in with a higher azimuth resolution than that of the original stripmap images. Detailed derivation of the azimuth super-resolution method, including the steps of two-dimensional dechirping, residual video phase (RVP) removal, data stitching and data correction, is provided. The restrictions of the proposed method are also discussed. Lastly, the presented approach is evaluated via both the single- and multi-target computer simulations. PMID:27304959

  12. NASA-ARC 91.5-cm airborne infrared telescope. [tracking mechanism

    NASA Technical Reports Server (NTRS)

    Mobley, R. E.; Brown, T. M.

    1979-01-01

    A 91.5 cm aperture telescope installed aboard NASA-Lockheed C-141A aircraft for the performance of infrared astronomy is described. A unique feature of the telescope is that its entire structure is supported by a 41 cm spherical air bearing which effectively uncouples it from aircraft angular motion, and with inertial stabilization and star tracking, limits tracking errors to less than 1 arc second in most applications. A general description of the system, a summary of its performance, and a detailed description of an offset tracking mechanism is presented.

  13. Tracking of airborne radionuclides from the damaged Fukushima Dai-ichi nuclear reactors by European networks.

    PubMed

    Masson, O; Baeza, A; Bieringer, J; Brudecki, K; Bucci, S; Cappai, M; Carvalho, F P; Connan, O; Cosma, C; Dalheimer, A; Didier, D; Depuydt, G; De Geer, L E; De Vismes, A; Gini, L; Groppi, F; Gudnason, K; Gurriaran, R; Hainz, D; Halldórsson, Ó; Hammond, D; Hanley, O; Holeý, K; Homoki, Zs; Ioannidou, A; Isajenko, K; Jankovic, M; Katzlberger, C; Kettunen, M; Kierepko, R; Kontro, R; Kwakman, P J M; Lecomte, M; Leon Vintro, L; Leppänen, A-P; Lind, B; Lujaniene, G; Mc Ginnity, P; Mc Mahon, C; Malá, H; Manenti, S; Manolopoulou, M; Mattila, A; Mauring, A; Mietelski, J W; Møller, B; Nielsen, S P; Nikolic, J; Overwater, R M W; Pálsson, S E; Papastefanou, C; Penev, I; Pham, M K; Povinec, P P; Ramebäck, H; Reis, M C; Ringer, W; Rodriguez, A; Rulík, P; Saey, P R J; Samsonov, V; Schlosser, C; Sgorbati, G; Silobritiene, B V; Söderström, C; Sogni, R; Solier, L; Sonck, M; Steinhauser, G; Steinkopff, T; Steinmann, P; Stoulos, S; Sýkora, I; Todorovic, D; Tooloutalaie, N; Tositti, L; Tschiersch, J; Ugron, A; Vagena, E; Vargas, A; Wershofen, H; Zhukova, O

    2011-09-15

    Radioactive emissions into the atmosphere from the damaged reactors of the Fukushima Dai-ichi nuclear power plant (NPP) started on March 12th, 2011. Among the various radionuclides released, iodine-131 ((131)I) and cesium isotopes ((137)Cs and (134)Cs) were transported across the Pacific toward the North American continent and reached Europe despite dispersion and washout along the route of the contaminated air masses. In Europe, the first signs of the releases were detected 7 days later while the first peak of activity level was observed between March 28th and March 30th. Time variations over a 20-day period and spatial variations across more than 150 sampling locations in Europe made it possible to characterize the contaminated air masses. After the Chernobyl accident, only a few measurements of the gaseous (131)I fraction were conducted compared to the number of measurements for the particulate fraction. Several studies had already pointed out the importance of the gaseous (131)I and the large underestimation of the total (131)I airborne activity level, and subsequent calculations of inhalation dose, if neglected. The measurements made across Europe following the releases from the Fukushima NPP reactors have provided a significant amount of new data on the ratio of the gaseous (131)I fraction to total (131)I, both on a spatial scale and its temporal variation. It can be pointed out that during the Fukushima event, the (134)Cs to (137)Cs ratio proved to be different from that observed after the Chernobyl accident. The data set provided in this paper is the most comprehensive survey of the main relevant airborne radionuclides from the Fukushima reactors, measured across Europe. A rough estimate of the total (131)I inventory that has passed over Europe during this period was <1% of the released amount. According to the measurements, airborne activity levels remain of no concern for public health in Europe. PMID:21809844

  14. A hardware/software simulation for the video tracking system of the Kuiper Airborne Observatory telescope

    NASA Technical Reports Server (NTRS)

    Boozer, G. A.; Mckibbin, D. D.; Haas, M. R.; Erickson, E. F.

    1984-01-01

    This simulator was created so that C-141 Kuiper Airborne Observatory investigators could test their Airborne Data Acquisition and Management System software on a system which is generally more accessible than the ADAMS on the plane. An investigator can currently test most of his data acquisition program using the data computer simulator in the Cave. (The Cave refers to the ground-based computer facilities for the KAO and the associated support personnel.) The main Cave computer is interfaced to the data computer simulator in order to simulate the data-Exec computer communications. However until now, there has been no way to test the data computer interface to the tracker. The simulator described here simulates both the KAO Exec and tracker computers with software which runs on the same Hewlett-Packard (HP) computer as the investigator's data acquisition program. A simulator control box is hardwired to the computer to provide monitoring of tracker functions, to provide an operator panel similar to the real tracker, and to simulate the 180 deg phase shifting of the chopper squre-wave reference with beam switching. If run in the Cave, one can use their Exec simulator and this tracker simulator.

  15. Man-in-the-loop study of filtering in airborne head tracking tasks

    NASA Technical Reports Server (NTRS)

    Lifshitz, S.; Merhav, S. J.

    1992-01-01

    A human-factors study is conducted of problems due to vibrations during the use of a helmet-mounted display (HMD) in tracking tasks whose major factors are target motion and head vibration. A method is proposed for improving aiming accuracy in such tracking tasks on the basis of (1) head-motion measurement and (2) the shifting of the reticle in the HMD in ways that inhibit much of the involuntary apparent motion of the reticle, relative to the target, and the nonvoluntary motion of the teleoperated device. The HMD inherently furnishes the visual feedback required by this scheme.

  16. Preliminary results from an airborne experiment using along-track interferometry for ground moving target indication

    NASA Technical Reports Server (NTRS)

    Chapin, Elaine; Chen, Curtis W.

    2005-01-01

    Synthetic aperture radar (SAR) along track interferometry (ATI) has been used extensively to measure ocean surface currents. Given its ability to measure small velocities of relatively radar-dark water surfaces, there is great potential that this technique can be adapted for ground moving target indication (GMTI) applications, particularly as a method for detecting very slwo targets with small radar cross sections. In this paper we describe preliminary results from an ATI GMTI experiment.

  17. Tracking the kinetics of intrahepatic immune responses by repeated fine needle aspiration of the liver

    PubMed Central

    Pembroke, Tom; Gallimore, Awen; Godkin, Andrew

    2015-01-01

    Liver disease is an increasing global health burden. The final sequalae of cirrhosis, liver failure and hepatocellular carcinoma are often the result of inflammation driven by intrahepatic lymphocytes. Accurate assessment of organ-specific diseases ideally employs tissue sampling though this is rarely performed. Here we report our experiences of utilising repeated fine needle aspirations (FNAs) to assess liver-derived leukocytes. In 88 patient samples, we obtained a mean of 36,959 lymphocytes from each FNA-derived biopsy (SD 22,319 cells, range 5034–91,242 cells) measured by flow cytometry. This quick technique required minimal analgesia compared to liver biopsy (p = 0.03); was well tolerated and safe, and hence repeated sampling up to 3 times within a week was feasible. We detail the technique to rapidly derive a single cell suspension suitable for multiparameter flow cytometry analysis. Finally we illustrate the importance of organ-derived sampling by showing that natural killer (NK) cells from FNA samples have a markedly altered phenotype compared to those assessed in peripheral blood. In combination these data validate FNA as a powerful and well-tolerated method of sampling intrahepatic lymphocytes to study the immunology of acute and chronic liver diseases. PMID:25914090

  18. ICESat-1 Elevation Changes of the Greenland and Antarctic Ice Sheets as Derived from Repeat Tracks, Crossovers, and Overlapping Footprints

    NASA Astrophysics Data System (ADS)

    Felikson, D.; Gunter, B. C.; Pie, N.; Schutz, B. E.; Urban, T. J.

    2012-12-01

    Knowledge of the long-term elevation changes of the Greenland and Antarctic ice sheets is critical for understanding their response to present and future climate change. There exist various methods for the computation of elevation changes from satellite altimetry, each with their own strengths and weaknesses. This presentation evaluates three particular methods using the recently reprocessed (Release 633) ICESat-1 laser altimetry data: repeat tracks, crossovers, and overlapping footprints. The analysis includes a description of the characteristics of each of the three methods, as well as a discussion of the spatial and temporal resolution of the computed height change maps. Additionally, inter-campaign measurement biases from the 18 distinct ICESat-1 laser campaigns are applied to the measurements. Advantages and disadvantages in the application of these biases for each method are presented.

  19. Quantifying the Flow Kinematics of Debris-Covered Glaciers with Repeat Airborne LiDAR and Photogrammetry

    NASA Astrophysics Data System (ADS)

    Holt, J. W.; Larsen, C. F.; Levy, J. S.; Petersen, E. I.

    2014-12-01

    Debris-covered glaciers and rock glaciers encompass a range of compositions and activity, including relict glaciers containing ice that has survived long after accumulation has ceased. Hence they are useful paleoclimate indicators in some cases, and if currently active will respond differently to ongoing climate change than glaciers without a protective cover. Their flow dynamics are not well understood, partially due to their typically slow velocities (centimeters per year in many cases); furthermore, their unique surface morphologies, including lobate fronts and arcuate ridges, likely result from viscous flow influenced by a combination of composition, structure, and climatic factors. However, basic connections between flow kinematics and surface morphology have not yet been established, limiting our ability to understand these features and extract paleoclimate information. In order to address this problem, we have acquired repeat, high-resolution topographic maps of debris-covered and rock glaciers in the Wrangell-St. Elias range of Alaska and Sierra Nevada, California. This was accomplished using both scanning LiDAR and photogrammetry to produce digital terrain models (DTMs) with approx. 25 cm resolution. Differencing the DTMs provides full-surface deformation fields that indicate up to meters of annual motion in some cases. The flow field is highly correlated with surface features; in particular, compressional ridges. We are undertaking surface geophysics measurements on Sourdough Rock Glacier in Alaska to relate internal structure and composition to the observed morphology and flow kinematics. Our results demonstrate the utility of repeat topographic mapping and will help provide new insights into the climatic significance of rock and debris-covered glaciers on both Earth and Mars.

  20. Spectrometers for Sky-Scanning, Sun-Tracking Atmospheric Research (4STAR) Upgrade to Full Sun-Sky-Cloud-Trace Gas Spectrometry Capability for Airborne Science

    NASA Astrophysics Data System (ADS)

    Dunagan, S. E.; Flynn, C. J.; Johnson, R. R.; Kacenelenbogen, M. S.; Knobelspiesse, K. D.; LeBlanc, S. E.; Livingston, J. M.; Redemann, J.; Russell, P. B.; Schmid, B.; Segal-Rosenhaimer, M.; Shinozuka, Y.

    2014-12-01

    The Spectrometers for Sky-Scanning, Sun-Tracking Atmospheric Research (4STAR) instrument has been developed at NASA Ames in collaboration with Pacific Northwest National Laboratory (PNNL) and NASA Goddard, supported substantially since 2009 by NASA's Radiation Science Program and Earth Science Technology Office. It combines grating spectrometers with fiber optic links to a tracking, scanning head to enable sun tracking, sky scanning, and zenith viewing. 4STAR builds on the long and productive heritage of the NASA Ames Airborne Tracking Sunphotometers (AATS-6 and -14), which have yielded more than 100 peer-reviewed publications and extensive archived data sets in many NASA Airborne Science campaigns from 1986 to the present. The baseline 4STAR instrument has provided extensive data supporting the TCAP (Two Column Aerosol Project, July 2012 & Feb. 2013), SEAC4RS (Studies of Emissions, Atmospheric Composition, Clouds and Climate Coupling by Regional Surveys, 2013), and ARISE (Arctic Radiation - IceBridge Sea and Ice Experiment, 2014), field campaigns.This poster presents plans and progress for an upgrade to the 4STAR instrument to achieve full science capability, including (1) direct-beam sun tracking measurements to derive aerosol optical depth spectra, (2) sky radiance measurements to retrieve aerosol absorption and type (via complex refractive index and mode-resolved size distribution), (3) cloud properties via zenith radiance, and (4) trace gas spectrometry. Technical progress in context with the governing physics is reported on several upgrades directed at improved light collection and usage, particularly as related to spectrally and radiometrically stable propagation through the collection light path. In addition, improvements to field calibration and verification, and flight operability and reliability are addressed.

  1. Neurobehavioral Toxicity of a Repeated Exposure (14 Days) to the Airborne Polycyclic Aromatic Hydrocarbon Fluorene in Adult Wistar Male Rats

    PubMed Central

    Peiffer, Julie; Cosnier, Frédéric; Grova, Nathalie; Nunge, Hervé; Salquèbre, Guillaume; Decret, Marie-Josèphe; Cossec, Benoît; Rychen, Guido; Appenzeller, Brice M. R.; Schroeder, Henri

    2013-01-01

    Fluorene is one of the most abundant polycyclic aromatic hydrocarbons in air and may contribute to the neurobehavioral alterations induced by the environmental exposure of humans to PAHs. Since no data are available on fluorene neurotoxicity, this study was conducted in adult rats to assess the behavioral toxicity of repeated fluorene inhalation exposure. Male rats (n = 18/group) were exposed nose-only to 1.5 or 150 ppb of fluorene 6 hours/day for 14 consecutive days, whereas the control animals were exposed to non-contaminated air. At the end of the exposure, animals were tested for activity and anxiety in an open-field and in an elevated-plus maze, for short-term memory in a Y-maze, and for spatial learning in an eight-arm maze. The results showed that the locomotor activity and the learning performances of the animals were unaffected by fluorene. In parallel, the fluorene-exposed rats showed a lower level of anxiety than controls in the open-field, but not in the elevated-plus maze, which is probably due to a possible difference in the aversive feature of the two mazes. In the same animals, increasing blood and brain levels of fluorene monohydroxylated metabolites (especially the 2-OH fluorene) were detected at both concentrations (1.5 and 150 ppb), demonstrating the exposure of the animals to the pollutant and showing the ability of this compound to be metabolized and to reach the cerebral compartment. The present study highlights the possibility for a 14-day fluorene exposure to induce some specific anxiety-related behavioral disturbances, and argues in favor of the susceptibility of the adult brain when exposed to volatile fluorene. PMID:23977039

  2. Using Eye Tracking to Observe Differential Effects of Repeated Readings for Second-grade Students as a Function of Achievement Level

    ERIC Educational Resources Information Center

    Zawoyski, Andrea M.; Ardoin, Scott P.; Binder, Katherine S.

    2015-01-01

    Repeated readings (RR) is an evidence-based instructional technique in which students read the same text multiple times. Currently, little is known about how effects of RR may differ based on students' achievement levels. Eye tracking provides a means for closely examining instructional effects because it permits measurement of subtle changes that…

  3. Von Willebrand gene tracking by single-tube automated fluorescent analysis of four short tandem repeat polymorphisms.

    PubMed

    Vidal, Francisco; Julià, Antoni; Altisent, Carme; Puig, Lluís; Gallardo, Doinique

    2005-05-01

    Molecular diagnosis of von Willebrand disease (VWD) has been hampered by the large size and complex genomic characteristics of the gene involved. For this reason, indirect methods using intragenic polymorphic markers described along the von Willebrand factor (VWF) gene are valuable tools for gene monitoring and linkage analysis. Several studies have demonstrated the four commonly utilized short tandem repeats (STRs), three located in intron 40 and one in the promoter region of the VWF gene, to be highly informative for this task. Our objective was t o develop a rapid, automated method to simultaneously analyze these four STRs for VWF gene tracking. Amplification of the four loci is achieved in a single multiplex fluorescent PCR which is then analyzed in the same run by capillary electrophoresis. Data processing with GeneScan and Genotyper software has simplified management and tabulation of the resulting haplotypes. Analysis of the VWF gene in DNA from 102 individuals (204 chromosomes) revealed that the three STRs within intron 40 showed significant linkage disequilibrium against each other but not against the VWP locus. Moreover, the combination of the four markers offers a high heterozygosity rate (>99%) that improves tracing VWF gene inheritance. In conclusion, the automated fluorescent capillary electrophoresis method presented here is an extremely rapid, simple and highly informative technique for association studies between VWD and the VWF gene in addition to genetic counseling and prenatal diagnosis by precise linkage analysis in VWD-affected families. PMID:15886817

  4. Repeat airborne LiDAR reveals the sensitivity of erosion and deposition patterns to bed topography and grain size distributions, Henry Mountains, Utah

    NASA Astrophysics Data System (ADS)

    Johnson, J. P.; Olinde, L.

    2013-12-01

    Repeat 2008 and 2011 NCALM airborne LiDAR data bracket a large 2010 storm over the Henry Mountains, Utah. This flood caused significant channel erosion and deposition, both of which locally exceeded 2 meters. We compare LiDAR difference maps to surface grain size distributions and channel bed topography to better understand factors that influenced the spatial distributions of elevation changes. Complete river bed topography was resolved over many kilometers because channels were dry when scanned. Systematic variations in grain size distributions among channels were measured by conducting pebble counts. Individual counts consisted of a minimum of 250 measured clasts to allow for robust statistics on coarse grain distributions, with grain sizes ranging from sand to boulders. Bed topography maps and field measurements indicate that channel morphology varies systematically with local grain size distributions and in particular with the abundance of boulders. Reach morphologies range from step-pools to gravel plane-beds along individual channels. We generalize channel topography using various roughness metrics and apply similar metrics to the spatial distribution of topographic changes. Channel width constrictions, common in these canyons, tend to cause net deposition upstream and erosion downstream of these reaches. We also found that areas of erosion and deposition tend to change more abruptly along channels with coarser sediment because immobile grains (often large boulders) act as local base level controls. However, it appears that overall erosion and deposition patterns are not strongly correlated with local channel slope or other characteristics of reach morphology. We interpret this to indicate that before the 2010 flood, channel reaches were already adjusted to local flow conditions in previous floods, through surface grain size sorting and other morphological adjustments. Although erosion and deposition were locally significant from the 2010 flood, most channel

  5. Evaluation of the repeatability and reproducibility of a suite of qPCR-based microbial source tracking methods.

    PubMed

    Ebentier, Darcy L; Hanley, Kaitlyn T; Cao, Yiping; Badgley, Brian D; Boehm, Alexandria B; Ervin, Jared S; Goodwin, Kelly D; Gourmelon, Michèle; Griffith, John F; Holden, Patricia A; Kelty, Catherine A; Lozach, Solen; McGee, Charles; Peed, Lindsay A; Raith, Meredith; Ryu, Hodon; Sadowsky, Michael J; Scott, Elizabeth A; Santo Domingo, Jorge; Schriewer, Alexander; Sinigalliano, Christopher D; Shanks, Orin C; Van De Werfhorst, Laurie C; Wang, Dan; Wuertz, Stefan; Jay, Jennifer A

    2013-11-15

    Many PCR-based methods for microbial source tracking (MST) have been developed and validated within individual research laboratories. Inter-laboratory validation of these methods, however, has been minimal, and the effects of protocol standardization regimes have not been thoroughly evaluated. Knowledge of factors influencing PCR in different laboratories is vital to future technology transfer for use of MST methods as a tool for water quality management. In this study, a blinded set of 64 filters (containing 32 duplicate samples generated from 12 composite fecal sources) were analyzed by three to five core laboratories with a suite of PCR-based methods utilizing standardized reagents and protocols. Repeatability (intra-laboratory variability) and reproducibility (inter-laboratory variability) of observed results were assessed. When standardized methodologies were used, intra- and inter-laboratory %CVs were generally low (median %CV 0.1-3.3% and 1.9-7.1%, respectively) and comparable to those observed in similar inter-laboratory validation studies performed on other methods of quantifying fecal indicator bacteria (FIB) in environmental samples. ANOVA of %CV values found three human-associated methods (BsteriF1, BacHum, and HF183Taqman) to be similarly reproducible (p > 0.05) and significantly more reproducible (p < 0.05) than HumM2. This was attributed to the increased variability associated with low target concentrations detected by HumM2 (approximately 1-2 log10copies/filter lower) compared to other human-associated methods. Cow-associated methods (BacCow and CowM2) were similarly reproducible (p > 0.05). When using standardized protocols, variance component analysis indicated sample type (fecal source and concentration) to be the major contributor to total variability with that from replicate filters and inter-laboratory analysis to be within the same order of magnitude but larger than inherent intra-laboratory variability. However, when reagents and

  6. An estimate of Greenland surface elevation changes derived from Envisat radar altimetry using combined repeat-track and cross-over results

    NASA Astrophysics Data System (ADS)

    Meister, R.; Sandberg, L.; Levinsen, J. F.; Khvorostovsky, K.; Forsberg, R.

    2013-12-01

    With the accelerating melt of the Greenland Ice Sheet (GIS), which is the world's second-largest ice sheet and contains enough ice to raise global sea level by 7m, an improvement in our understanding of such changes is required. Envisat radar altimetry data can be used to provide information on the surface elevation changes the GIS is experiencing. This study is the first of its kind to explore the use of repeat track radar altimetry data to derive Greenland surface height changes. Because of the large footprint of the Envisat RA-2 altimeter (on the order of 5km), it has previously been assumed that towards the edges of the ice sheet, where steep slopes exist, radar altimetry data cannot be used to resolve changes with sufficient accuracy. However, here we present that a newly developed combination of repeat-track and cross-over data provide realistic estimates of ice-sheet-wide surface height changes. The repeat-track method makes use of all available observations and hence increases the number of measurements compared to the cross-over method, which only estimates changes at the location where ascending and a descending paths cross. Each method has its advantages; whilst the repeat-track method provides estimates at a higher spatial resolution, the cross-over method benefits from comparatively low errors. After derivation of dH/dt rates for the entire ice sheet from both methods, data were combined based on an analysis of their respective errors. As a generalisation, it can be said that near the ice sheet margins repeat-track data were used, whereas in the interior, the cross-over method provided more reliable results. Initial results show that for the outlet glacier Jakobshavn Isbræ, both the repeat-track and the cross-over methods measure similar thinning patterns, thus increasing confidence in the ability of radar altimetry to measure changes on the margins of the GIS. We compare our resulting map of surface height changes to dH/dt patterns derived from the

  7. Validating Above-cloud Aerosol Optical Depth Retrieved from MODIS using NASA Ames Airborne Sun-Tracking Photometric and Spectrometric (AATS and 4STAR) Measurements

    NASA Astrophysics Data System (ADS)

    Jethva, H. T.; Torres, O.; Remer, L. A.; Redemann, J.; Dunagan, S. E.; Livingston, J. M.; Shinozuka, Y.; Kacenelenbogen, M. S.; Segal-Rosenhaimer, M.

    2014-12-01

    Absorbing aerosols produced from biomass burning and dust outbreaks are often found to overlay the lower level cloud decks as evident in the satellite images. In contrast to the cloud-free atmosphere, in which aerosols generally tend to cool the atmosphere, the presence of absorbing aerosols above cloud poses greater potential of exerting positive radiative effects (warming) whose magnitude directly depends on the aerosol loading above cloud, optical properties of clouds and aerosols, and cloud fraction. In recent years, development of algorithms that exploit satellite-based passive measurements of ultraviolet (UV), visible, and polarized light as well as lidar-based active measurements constitute a major breakthrough in the field of remote sensing of aerosols. While the unprecedented quantitative information on aerosol loading above cloud is now available from NASA's A-train sensors, a greater question remains ahead: How to validate the satellite retrievals of above-cloud aerosols (ACA)? Direct measurements of ACA such as carried out by the NASA Ames Airborne Tracking Sunphotometer (AATS) and Spectrometer for Sky-Scanning, Sun-Tracking Atmospheric Research (4STAR) can be of immense help in validating ACA retrievals. In this study, we validate the ACA optical depth retrieved using the 'color ratio' (CR) method applied to the MODIS cloudy-sky reflectance by using the airborne AATS and 4STAR measurements. A thorough search of the historic AATS-4STAR database collected during different field campaigns revealed five events where biomass burning, dust, and wildfire-emitted aerosols were found to overlay lower level cloud decks observed during SAFARI-2000, ACE-ASIA 2001, and SEAC4RS-2013, respectively. The co-located satellite-airborne measurements revealed a good agreement (root-mean-square-error<0.1 for Aerosol Optical Depth (AOD) at 500 nm) with most matchups falling within the estimated uncertainties in the MODIS retrievals (-10% to +50%). An extensive validation of

  8. Evaluation of the repeatability and reproducibility of a suite of qPCR based microbial source tracking methods

    EPA Science Inventory

    Many PCR-based methods for microbial source tracking (MST) have been developed and validated within individual research laboratories. Inter-laboratory validation of these methods, however, has been minimal, and the effects of protocol standardization regimes have not been thor...

  9. Mid-tropospheric Moisture Variations During the Development of Hurricane Karl as Resolved by Airborne GPS Radio Occultation with Open Loop Tracking

    NASA Astrophysics Data System (ADS)

    Haase, J. S.; Murphy, B.; Wang, K. N.; Garrison, J. L.; Adhikari, L.; Xie, F.

    2015-12-01

    The development of hurricane Karl in 2010 was investigated with dropsonde and airborne radio occultation (ARO) measurements from the stage of tropical disturbance within an easterly wave through to genesis of the tropical storm. Infrared imagery showed deep convection with extensive cold cloud tops on 11 September however the storm failed to develop until 3 days later. One possible explanation is the horizontal offset of the mid and lower level circulation centers. We illustrate with airborne radio occultation measurements additional information on the moisture distribution during this stage of development that indicates that average mid-level moisture was lower the following day and then increased again over the next two days prior to development. High sample rate RF data recorded by the GNSS instrument system for multistatic and occultation sensing (GISMOS) was analyzed with a version of the Purdue Software Receiver that has open-loop tracking implemented. Open loop tracking eliminates the feedback loop of conventional receivers that fails in the complex signal propagation environment typical of atmosphere with sharp moisture gradients. The open-loop excess phase profiles routinely sample below 4 km, with half of the profiles extending below 2 km. We retrieve slanted vertical profiles of atmospheric refractivity that can be considered a proxy for moisture in this tropical environment. We illustrate that in the mid to upper troposphere, ARO refractivity profiles sampling different areas within the tropical wave showed characteristics that were consistent with (~150 to 200 km scale) horizontal moisture gradients present in the NWP model representation of the developing tropical storm. Variation in refractivity preceding the development of the pre-Karl system is consistent with increasing moisture near the storm center. The ARO observations almost double the amount of thermodynamic data over that provided by the dropsondes. They provide interesting complementary

  10. An optimized method for tremor detection and temporal tracking through repeated second order moment calculations on the surface EMG signal.

    PubMed

    De Marchis, Cristiano; Schmid, Maurizio; Conforto, Silvia

    2012-11-01

    In this study, the problem of detecting and tracking tremor from the surface myoelectric signal is addressed. A method based on the calculation of a Second Order Moment Function (SOMF) inside a window W sliding over the sEMG signal is here presented. An analytical formulation of the detector allows the extraction of the optimal parameters characterizing the algorithm. Performance of the optimized method is assessed on a set of synthetic tremor sEMG signals in terms of sensitivity, precision and accuracy through the use of a properly defined cost function able to explain the overall detector performance. The obtained results are compared to those emerging from the application of optimized versions of traditional detection techniques. Once tested on a database of synthetic tremor sEMG data, a quantitative assessment of the SOMF algorithm performance is carried out on experimental tremor sEMG signals recorded from two patients affected by Essential Tremor and from two patients affected by Parkinson's Disease. The SOMF algorithm outperforms the traditional techniques both in detecting (sensitivity and positive predictive value >99% for SNR higher than 3dB) and in estimating timings of muscular tremor bursts (bias and standard deviation on the estimation of the onset and offset time instants lower than 8ms). Its independence from the SNR level and its low computational cost make it suitable for real-time implementation and clinical use. PMID:22257701

  11. The Microtubule Plus-End Tracking Protein ARMADILLO-REPEAT KINESIN1 Promotes Microtubule Catastrophe in Arabidopsis[W][OPEN

    PubMed Central

    Eng, Ryan Christopher; Wasteneys, Geoffrey O.

    2014-01-01

    Microtubule dynamics are critically important for plant cell development. Here, we show that Arabidopsis thaliana ARMADILLO-REPEAT KINESIN1 (ARK1) plays a key role in root hair tip growth by promoting microtubule catastrophe events. This destabilizing activity appears to maintain adequate free tubulin concentrations in order to permit rapid microtubule growth, which in turn is correlated with uniform tip growth. Microtubules in ark1-1 root hairs exhibited reduced catastrophe frequency and slower growth velocities, both of which were restored by low concentrations of the microtubule-destabilizing drug oryzalin. An ARK1-GFP (green fluorescent protein) fusion protein expressed under its endogenous promoter localized to growing microtubule plus ends and rescued the ark1-1 root hair phenotype. Transient overexpression of ARK1-RFP (red fluorescent protein) increased microtubule catastrophe frequency. ARK1-fusion protein constructs lacking the N-terminal motor domain still labeled microtubules, suggesting the existence of a second microtubule binding domain at the C terminus of ARK1. ARK1-GFP was broadly expressed in seedlings, but mutant phenotypes were restricted to root hairs, indicating that ARK1’s function is redundant in cells other than those forming root hairs. PMID:25159991

  12. Studies of Grounding Line Migration Over Rutofrd Ice Stream Using 3D Short Repeat-Time Series From Multi-Track InSAR Acquisitions.

    NASA Astrophysics Data System (ADS)

    Milillo, P.; Minchew, B. M.; Riel, B. V.; Simons, M.; Gardner, A. S.; Agram, P. S.

    2015-12-01

    It has long been known that basal mechanics of ice streams are sensitive to short- timescale hourly to seasonal forcings, such as water pressure fluctuations and tidal loading as well as long-timescale (yearly to decadal) thinning. Designing SAR short repeat time observations to cover nearly an entire test-site in Antarctica from ascending and descending orbital directions, using every available SAR satellite is fundamental for understanding a new class of phenomena, underlying the physics of glaciers and ice streams. Understanding grounding-line dynamics is necessary for predictions of long-term ice-sheet stability. However, despite growing observations of the tidal influence on grounding-line migration, this short-timescale migration is poorly understood, with most modeling attempts assuming beam theory to calculate displacements. Knowing the position of the grounding line with accuracy is important for the global mass balance of ice sheets or for quantitatively modeling the mechanical interaction between ice shelves and ice sheets. Here we present a general method for retrieving three dimensional displacement vector given a set of multiple tracks, multiple geometry SAR acquisitions. The algorithm extends the single line of sight mathematical framework to the four spatial and temporal dimensions including both range and azimuth measurements. We designed COSMO-SkyMed (CSK) observations of Rutford Ice Stream to cover nearly the grounding zone from ascending and descending orbital directions using every available CSK satellite This spatially comprehensive observational scheme allowed us to derive time series of the 3-dimensional surface displacement for the grounding zone, facilitating studies of ice stream mechanics and tidally induced grounding line migrations with unprecedented spatial extent and temporal resolution. Having a constellation with occasional 1- day repeat time and an average 4-days repeat time is beneficial when looking at displacements of more than

  13. Tracking long-range transported upper-tropospheric pollution layers with a newly developed airborne Hyperspectral Sun/Sky spectrometer (4STAR): Results from the TCAP 2012 campaign

    NASA Astrophysics Data System (ADS)

    Segal-Rosenhaimer, M.; Russell, P. B.; Schmid, B.; Redemann, J.; Livingston, J. M.; Flynn, C. J.; Johnson, R.; Dunagan, S.; Shinozuka, Y.; Herman, J. R.; Cede, A.; Abuhassan, N.; Comstock, J. M.; Hubbe, J.

    2013-12-01

    TCAP, the Two Column Aerosol Project, was aimed at providing a detailed set of observations to investigate topics related to radiation and aerosol-cloud interactions, and to learn about aging and transport of atmospheric aerosols and gaseous constituents that are related to tropospheric pollution events. During the year-long campaign, an intensive airborne deployment was held in the summer of 2012 based at the Hyannis airport, Cape-Cod, MA. In the course of the campaign, the newly developed Spectrometer for Sky-Scanning, Sun-Tracking Atmospheric Research (4STAR) flew onboard the DOE Gulfstream 1 (G-1) aircraft, together with a suite of in-situ instruments to measure atmospheric state parameters and aerosol and cloud characteristics. One of the unique features of the 4STAR instrument, stemming from its design using grating spectrometers that cover the UV-VIS-SWIR spectral range (i.e. 350-1700nm), is its capability to measure atmospheric trace gases such as water vapor, O3 and NO2 concurrently with spectrally resolved aerosol optical depth (AOD). Here, we utilize the 4STAR measurements above the planetary boundary layer (PBL) (i.e. above 3000 meters) to investigate atmospheric composition of elevated pollution layers transported from the continental US and Canada during the TCAP summer phase. The 4STAR-retrieved values of AOD at 500 nm, Ångstrom exponent (AE) at 500 nm, columnar water vapor (CWV), and NO2 are used as variables in a k-means clustering algorithm to determine the atmospheric composition characteristics of the observed elevated polluted layers during the July flights. We found that, compared to AOD, NO2 displays less variability in plumes that are related to biomass-burning (BB) emissions over the course of several days. HYSPLIT back-trajectory analysis has confirmed our clustering results of two major air-mass sources: a relatively dry and clean upper tropospheric source and a humid, polluted one. Our clustering analysis, resulting in different ocean

  14. Tracking Fine-Grain Phenological Dynamics at a Landscape Extent Using a Network of Near-Surface Digital Repeat Photography Stations in West Greenland

    NASA Astrophysics Data System (ADS)

    Kerby, J.; Post, E.

    2014-12-01

    The phenology of vegetation emergence in the Arctic is highly sensitive to climatic fluctuations. Spring phenology drives ecological processes across local, population, and ecosystem scales. Traditional approaches to capturing spatio-temporal variation in the annual timing and pace of Arctic green-up, like satellite-derived and plot-level records, are limited by trade-offs in the grain and extent of monitoring through both space and time. Recent studies demonstrate the utility of tracking canopy phenology using near-surface digital repeat photography (phenocams) to overcome spatial and temporal grain limitations at the extent of individual plants or vegetation stands. However, our understanding of how fine-grain phenological dynamics scale to landscape extents is incomplete. Here we report on the fine-grain green-up dynamics of a low-Arctic tundra system in West Greenland at the extent of a caribou calving range (40 km2) using three years (2012-2014) of phenological records derived from a network of 50 phenocams, field observations, and high-resolution satellite imagery. Using geostatistics and multiple-regression models, we characterize spatiotemporal patterns of plant phenology, landscape controls on the timing of emergence of common shrub and graminoid species, and assess scale-dependency in patterns of vegetation green-up. We link these results with coarse-grained satellite records of plant phenology to clarify how fine-grained dynamics contribute to the widely reported broad-scale patterns of phenological and ecological change in the Arctic.

  15. Chemical characterization and toxicologic evaluation of airborne mixtures: inhalation toxicology of diesel fuel obscurant aerosol in Spargue-Dawley rats. Final report, phase 2, repeated exposures

    SciTech Connect

    Dalbey, W.; Lock, S., Schmoyer, R.

    1982-07-01

    A series of repeated exposures of rats to aerosolized diesel fuel was performed to help establish indices of potential toxicity resulting from aerosol exposure and the relative importance of duration of exposures, the frequence of exposures, and aerosol concentration in the induction of observed lesions. Body weight and food consumption were recorded on a weekly basis. Assays were performed on selected animals within 1-2 days after the last exposure or after 2 weeks without exposure. Endpoints included number and phagocytic activity of pulmonary free cells, pulmonary function tests, neurotoxicity assays, clinical chemistry, organ weights, and histopathology. Data were analyzed by analysis of variance. After exposure, the primary target organ was the lungs. Focal accumulations of pulmonary free cells were observed in the lung parenchyma, associated with thickening and hypercellularity of alveolar walls. The number of lavaged pulmonary free cells correlated well with histologic observations, remaining elevated after two weeks without exposure. Lung volumes were altered by exposure, including increased FRC, decreased TLC, and decreased VC. Carbon monoxide diffusing capacity was decreased in several exposed groups also. None of the more systemic changes observed were considered to be of biologic significance, even though the exposure conditions were considered to result in a maximum tolerated dose. Frequency of exposure was the dominant variable over the range of parameters used in this study, 3 exposures/wk being more deleterious than 1/week. Variation in duration of exposure appeared to have very little effect and a dose-response was often not apparent with differences in concentration. 12 references, 13 figures, 18 tables.

  16. Upgrade of the NASA 4STAR (Spectrometer for Sky-Scanning, Sun-Tracking Atmospheric Research) to its Full Science Capability of Sun-Sky-Cloud-Trace Gas Spectrometry in Airborne Science Deployments

    NASA Technical Reports Server (NTRS)

    Johnson, Roy R.; Russell, P.; Dunagan, S.; Redemann, J.; Shinozuka, Y.; Segal-Rosenheimer, M.; LeBlanc, S.; Flynn, C.; Schmid, B.; Livingston, J.

    2014-01-01

    The objectives of this task in the AITT (Airborne Instrument Technology Transition) Program are to (1) upgrade the NASA 4STAR (Spectrometer for Sky-Scanning, Sun-Tracking Atmospheric Research) instrument to its full science capability of measuring (a) direct-beam sun transmission to derive aerosol optical depth spectra, (b) sky radiance vs scattering angle to retrieve aerosol absorption and type (via complex refractive index spectra, shape, and mode-resolved size distribution), (c) zenith radiance for cloud properties, and (d) hyperspectral signals for trace gas retrievals, and (2) demonstrate its suitability for deployment in challenging NASA airborne multiinstrument campaigns. 4STAR combines airborne sun tracking, sky scanning, and zenith pointing with diffraction spectroscopy to improve knowledge of atmospheric constituents and their links to air pollution, radiant energy budgets (hence climate), and remote measurements of Earth's surfaces. Direct beam hyperspectral measurement of optical depth improves retrievals of gas constituents and determination of aerosol properties. Sky scanning enhances retrievals of aerosol type and size distribution. 4STAR measurements are intended to tighten the closure between satellite and ground-based measurements. 4STAR incorporates a modular sun-tracking/sky-scanning optical head with fiber optic signal transmission to rack mounted spectrometers, permitting miniaturization of the external optical head, and future detector evolution. 4STAR test flights, as well as science flights in the 2012-13 TCAP (Two-Column Aerosol Project) and 2013 SEAC4RS (Studies of Emissions and Atmospheric Composition, Clouds and Climate Coupling by Regional Surveys) have demonstrated that the following are essential for 4STAR to achieve its full science potential: (1) Calibration stability for both direct-beam irradiance and sky radiance, (2) Improved light collection and usage, and (3) Improved flight operability and reliability. A particular challenge

  17. UAVSAR: An Airborne Window on Earth Surface Deformation

    NASA Technical Reports Server (NTRS)

    Hensley, Scott

    2011-01-01

    This study demonstrates that UAVSAR's precision autopilot and electronic steering have allowed for the reliable collection of airborne repeat pass radar interferometric data for deformation mapping. Deformation maps from temporal scales ranging from hours to months over a variety of signals of geophysical interest illustrate the utility of UAVSAR airborne repeat pass interferometry to these studies.

  18. Fourth Airborne Geoscience Workshop

    NASA Technical Reports Server (NTRS)

    1991-01-01

    The focus of the workshop was on how the airborne community can assist in achieving the goals of the Global Change Research Program. The many activities that employ airborne platforms and sensors were discussed: platforms and instrument development; airborne oceanography; lidar research; SAR measurements; Doppler radar; laser measurements; cloud physics; airborne experiments; airborne microwave measurements; and airborne data collection.

  19. Airborne laser

    NASA Astrophysics Data System (ADS)

    Lamberson, Steven E.

    2002-06-01

    The US Air Force Airborne Laser (ABL) is an airborne, megawatt-class laser system with a state-of-the-art atmospheric compensation system to destroy enemy ballistic missiles at long ranges. This system will provide both deterrence and defense against the use of such weapons during conflicts. This paper provides an overview of the ABL weapon system including: the notional operational concept, the development approach and schedule, the overall aircraft configuration, the technologies being incorporated in the ABL, and the risk reduction approach being utilized to ensure program success.

  20. Integration of Airborne Aerosol Prediction Systems and Vegetation Phenology to Track Pollen for Asthma Alerts in Public Health Decision Support Systems

    NASA Technical Reports Server (NTRS)

    Luvall, Jeffrey C.; Sprigg, William A.; Huete, Alfredo; Pejanovic, Goran; Nickovic, Slobodan; Krapfl, Heide; Budge, Amy; Zelicoff, Alan; VandeWater, Peter K.; Levetin, Estelle; Losleben, Mark; Weltzin, Jake

    2009-01-01

    The residual signal indicates that the pollen event may influence the seasonal signal to an extent that would allow detection, given accurate QA filtering and BRDF corrections. MODIS daily reflectances increased during the pollen season. The DREAM model (PREAM) was successfully modified for use with pollen and may provide 24-36 hour running pollen forecasts. Publicly available pollen forecasts are linked to general weather patterns and roughly-known species phenologies. These are too coarse for timely health interventions. PREAM addresses this key data gap so that targeting intervention measures can be determined temporally and geospatially. The New Mexico Department of Health (NMDOH) as part of its Environmental Public Health Tracking Network (EPHTN) would use PREAM a tool for alerting the public in advance of pollen bursts to intervene and reduce the health impact on asthma populations at risk.

  1. Geodetic and geophysical results from a Taiwan airborne gravity survey: Data reduction and accuracy assessment

    NASA Astrophysics Data System (ADS)

    Hwang, Cheinway; Hsiao, Yu-Shen; Shih, Hsuan-Chang; Yang, Ming; Chen, Kwo-Hwa; Forsberg, Rene; Olesen, Arne V.

    2007-04-01

    An airborne gravity survey was conducted over Taiwan using a LaCoste and Romberg (LCR) System II air-sea gravimeter with gravity and global positioning system (GPS) data sampled at 1 Hz. The aircraft trajectories were determined using a GPS network kinematic adjustment relative to eight GPS tracking stations. Long-wavelength errors in position are reduced when doing numerical differentiations for velocity and acceleration. A procedure for computing resolvable wavelength of error-free airborne gravimetry is derived. The accuracy requirements of position, velocity, and accelerations for a 1-mgal accuracy in gravity anomaly are derived. GPS will fulfill these requirements except for vertical acceleration. An iterative Gaussian filter is used to reduce errors in vertical acceleration. A compromising filter width for noise reduction and gravity detail is 150 s. The airborne gravity anomalies are compared with surface values, and large differences are found over high mountains where the gravity field is rough and surface data density is low. The root mean square (RMS) crossover differences before and after a bias-only adjustment are 4.92 and 2.88 mgal, the latter corresponding to a 2-mgal standard error in gravity anomaly. Repeatability analyses at two survey lines suggest that GPS is the dominating factor affecting the repeatability. Fourier transform and least-squares collocation are used for downward continuation, and the latter produces a better result. Two geoid models are computed, one using airborne and surface gravity data and the other using surface data only, and the former yields a better agreement with the GPS-derived geoidal heights. Bouguer anomalies derived from airborne gravity by a rigorous numerical integration reveal important tectonic features.

  2. Integration for Airborne Dust Prediction Systems and Vegetation Phenology to Track Pollen for Asthma Alerts in Public Health Decision Support Systems

    NASA Technical Reports Server (NTRS)

    Luvall, J. C.; Sprigg, W. A.; Nickovic, S.; Huete, A.; Budge, A.; Flowers, L.

    2008-01-01

    The objective of the program is to assess the feasibility of combining a dust transport model with MODIS derived phenology to study pollen transport for integration with a public health decision support system. The use of pollen information has specifically be identified as a critical need by the New Mexico State Health department for inclusion in the Environmental Public Health Tracking (EPHT) program. Material and methods: Pollen can be transported great distances. Local observations of plan phenology may be consistent with the timing and source of pollen collected by pollen sampling instruments. The Dust REgional Atmospheric Model (DREAM) is an integrated modeling system designed to accurately describe the dust cycle in the atmosphere. The dust modules of the entire system incorporate the state of the art parameterization of all the major phases of the atmospheric dust life such as production, diffusion, advection, and removal. These modules also include effects of the particles size distribution on aerosol dispersion. The model was modified to use pollen sources instead of dust. Pollen release was estimated based on satellite-derived phenology of key plan species and vegetation communities. The MODIS surface reflectance product (MOD09) provided information on the start of the plant growing season, growth stage, and pollen release. The resulting deterministic model is useful for predicting and simulating pollen emission and downwind concentration to study details of phenology and meteorology and their dependencies. The proposed linkage in this project provided critical information on the location timing and modeled transport of pollen directly to the EPHT> This information is useful to support the centers for disease control and prevention (CDC)'s National EPHT and the state of New Mexico environmental public health decision support for asthma and allergies alerts.

  3. Repeating thermocouple

    SciTech Connect

    Falk, R. A.

    1985-06-04

    Disclosed herein is a repeating use thermocouple assembly and method of making the same in which a cavity adjacent the tip of the thermocouple is filled with a thermosetting foundry sand and baked in place to provide support for the thermocouple tube without causing stresses during use which could cause breakage of the thermocouple tube.

  4. Antenna-array, phase quadrature tracking system

    NASA Technical Reports Server (NTRS)

    Cubley, H. D.

    1970-01-01

    Phase relationship between input signals appearing on widely-spaced parallel connected antenna elements in array is automatically adjusted in phase quadrature tracking system. Compact and lightweight design permit use in wide variety of airborne communications networks.

  5. Airborne eddy covariance measurements of methane over mid-latitude and sub-Arctic wetlands

    NASA Astrophysics Data System (ADS)

    Sachs, T.; Hartmann, J.

    2011-12-01

    Methane fluxes between terrestrial ecosystems and the atmosphere are highly variable in space and time. This is especially valid for wetlands, which are often characterized by extremely small-scale spatial heterogeneity. While closed chambers and eddy covariance methods are well suited for identifying individual contributions from micro-sites, for local process studies, for controlled experiments, and for investigating the temporal variability of fluxes, they may not necessarily be representative of larger spatial scales and of resolving interactions between methane emissions and boundary layer processes. A comprehensive assessment of the role of natural wetlands in atmospheric CH4 dynamics would thus benefit greatly from regional, i.e. airborne flux and concentrations measurements. Airborne measurements allow sufficiently large spatial coverage and may therefore be significantly more representative than sparse ground-based measurements, especially in remote and extensive northern wetlands and permafrost areas. In June 2011 we used a Los Gatos RMT-200 Fast Methane Analyzer and the onboard turbulence nose boom of the Polar-5 research aircraft to conduct airborne eddy covariance measurements of methane emissions over a variety of anthropogenic and natural targets. These included rewetted areas in northeastern Germany and extensive boreal and sub-Arctic wetlands in near Hyytiälä, Sodankylä, and Kaamanen in Finland. We will present preliminary results obtained during repeated survey flights along flight tracks of several kilometers to tens of kilometers.

  6. Sandia Multispectral Airborne Lidar for UAV Deployment

    SciTech Connect

    Daniels, J.W.; Hargis,Jr. P.J.; Henson, T.D.; Jordan, J.D.; Lang, A.R.; Schmitt, R.L.

    1998-10-23

    Sandia National Laboratories has initiated the development of an airborne system for W laser remote sensing measurements. System applications include the detection of effluents associated with the proliferation of weapons of mass destruction and the detection of biological weapon aerosols. This paper discusses the status of the conceptual design development and plans for both the airborne payload (pointing and tracking, laser transmitter, and telescope receiver) and the Altus unmanned aerospace vehicle platform. Hardware design constraints necessary to maintain system weight, power, and volume limitations of the flight platform are identified.

  7. Status of a UAV SAR Designed for Repeat Pass Interferometry for Deformation Measurements

    NASA Technical Reports Server (NTRS)

    Hensley, Scott; Wheeler, Kevin; Hoffman, Jim; Miller, Tim; Lou, Yunling; Muellerschoen, Ron; Zebker, Howard; Madsen, Soren; Rosen, Paul

    2004-01-01

    Under the NASA ESTO sponsored Instrument Incubator Program we have designed a lightweight, reconfigurable polarimetric L-band SAR designed for repeat pass deformation measurements of rapidly deforming surfaces of geophysical interest such as volcanoes or earthquakes. This radar will be installed on an unmanned airborne vehicle (UAV) or a lightweight, high-altitude, and long endurance platform such as the Proteus. After a study of suitable available platforms we selected the Proteus for initial development and testing of the system. We want to control the repeat track capability of the aircraft to be within a 10 m tube to support the repeat deformation capability. We conducted tests with the Proteus using real-time GPS with sub-meter accuracy to see if pilots could fly the aircraft within the desired tube. Our results show that pilots are unable to fly the aircraft with the desired accuracy and therefore an augmented autopilot will be required to meet these objectives. Based on the Proteus flying altitude of 13.7 km (45,000 ft), we are designing a fully polarimetric L-band radar with 80 MHz bandwidth and 16 km range swath. This radar will have an active electronic beam steering antenna to achieve Doppler centroid stability that is necessary for repeat-pass interferometry (RPI). This paper will present are design criteria, current design and expected science applications.

  8. Airborne oceanographic lidar system

    NASA Technical Reports Server (NTRS)

    Bressel, C.; Itzkan, I.; Nunes, J. E.; Hoge, F.

    1977-01-01

    The characteristics of an Airborne Oceanographic Lidar (AOL) are given. The AOL system is described and its potential for various measurement applications including bathymetry and fluorosensing is discussed.

  9. NASA's Coastal and Ocean Airborne Science Testbed

    NASA Astrophysics Data System (ADS)

    Guild, L. S.; Dungan, J. L.; Edwards, M.; Russell, P. B.; Morrow, J. H.; Hooker, S.; Myers, J.; Kudela, R. M.; Dunagan, S.; Soulage, M.; Ellis, T.; Clinton, N. E.; Lobitz, B.; Martin, K.; Zell, P.; Berthold, R. W.; Smith, C.; Andrew, D.; Gore, W.; Torres, J.

    2011-12-01

    The Coastal and Ocean Airborne Science Testbed (COAST) Project is a NASA Earth-science flight mission that will advance coastal ecosystems research by providing a unique airborne payload optimized for remote sensing in the optically complex coastal zone. Teaming NASA Ames scientists and engineers with Biospherical Instruments, Inc. (San Diego) and UC Santa Cruz, the airborne COAST instrument suite combines a customized imaging spectrometer, sunphotometer system, and a new bio-optical radiometer package to obtain ocean/coastal/atmosphere data simultaneously in flight for the first time. The imaging spectrometer (Headwall) is optimized in the blue region of the spectrum to emphasize remote sensing of marine and freshwater ecosystems. Simultaneous measurements supporting empirical atmospheric correction of image data will be accomplished using the Ames Airborne Tracking Sunphotometer (AATS-14). Based on optical detectors called microradiometers, the NASA Ocean Biology and Biogeochemistry Calibration and Validation (cal/val) Office team has deployed advanced commercial off-the-shelf instrumentation that provides in situ measurements of the apparent optical properties at the land/ocean boundary including optically shallow aquatic ecosystems (e.g., lakes, estuaries, coral reefs). A complimentary microradiometer instrument package (Biospherical Instruments, Inc.), optimized for use above water, will be flown for the first time with the airborne instrument suite. Details of the October 2011 COAST airborne mission over Monterey Bay demonstrating this new airborne instrument suite capability will be presented, with associated preliminary data on coastal ocean color products, coincident spatial and temporal data on aerosol optical depth and water vapor column content, as well as derived exact water-leaving radiances.

  10. Capturing and tracking performance of the horizontal guidance and control systems of the terminal configured vehicle

    NASA Technical Reports Server (NTRS)

    Knox, C. E.

    1979-01-01

    A twin-jet commercial transport equipped with digital navigation, guidance, and control systems and advanced electronic display system was used for airborne operational research. The results of flight tests which evaluated a second-order horizontal-path guidance control law and the autopilot and airplane response are presented. This evaluation was accomplished through analysis of recorded flight data and through pilot opinion of the airplane maneuvers during automatic path-capture scenarios and path tracking. Four different path captures were flown at a ground speed of approximately 160 knots and repeated at approximately 300 knots. Path tracking tracking error was measured in terms of cross track error along two paths: one pat at cruise speeds and one at airport-terminal-area speeds. The path tracking accuracy and the smoothness of the airplane maneuvers were judged satisfactory for high speeds; however, at lower speeds the control law design should be improved so that tracking will be more accurate for operations in the airport terminal area.

  11. Comparison of retracking algorithms using airborne radar and laser altimeter measurements of the Greenland ice sheet

    NASA Astrophysics Data System (ADS)

    Ferraro, Ellen J.; Swift, Calvin T.

    1995-05-01

    In 1991, NASA conducted a multisensor airborne altimetry experiment over the Greenland ice sheet. The experiment consisted of ten flights. Four types of radar altimeter retracking algorithms which include the Advanced Application Flight Experiment (AAFE) Ku-band altimeter, the NASA Airborne Oceanographic Lidar (AOL), the NASA Airborne Terrain Laser Altimeter System (ATLAS) and the NASA Ka-band Surface Contour Radar (SCR) were used. In this paper, these four continental ice sheet radar altimeter tracking algorithms were compared.

  12. Real-time simulation of an airborne radar for overwater approaches

    NASA Technical Reports Server (NTRS)

    Karmarkar, J.; Clark, D.

    1982-01-01

    Software developed to provide a real time simulation of an airborne radar for overwater approaches to oil rig platforms is documented. The simulation is used to study advanced concepts for enhancement of airborne radar approaches (ARA) in order to reduce crew workload, improve approach tracking precision, and reduce weather minimums. ARA's are currently used for offshore helicopter operations to and from oil rigs.

  13. UAVSAR: A New NASA Airborne SAR System for Science and Technology Research

    NASA Technical Reports Server (NTRS)

    Rosen, Paul A.; Hensley, Scott; Wheeler, Kevin; Sadowy, Greg; Miller, Tim; Shaffer, Scott; Muellerschoen, Ron; Jones, Cathleen; Zebker, Howard; Madsen, Soren

    2006-01-01

    NASA's Jet Propulsion Laboratory is currently building a reconfigurable, polarimetric L-band synthetic aperture radar (SAR), specifically designed to acquire airborne repeat track SAR data for differential interferometric measurements. Differentian interferometry can provide key deformation measurements, important for studies of earthquakes, volcanoes and other dynamically changing phenomena. Using precision real-time GPS and a sensor controlled flight management system, the system will be able to fly predefined paths with great precision. The expected performance of the flight control system will constrain the flight path to be within a 10 m diameter tube about the desired flight track. The radar will be designed to be operable on a UAV (Unpiloted Aria1 Vehicle) but will initially be demonstrated on a NASA Gulfstream III. The radar will be fully polarimetric, with a range bandwidth of 80 MHz (2 m range resolution), and will support a 16 km range swath. The antenna will be electronically steered along track to assure that the antenna beam can be directed independently, regardless of the wind direction and speed. Other features supported by the antenna include elevation monopulse and pulse-to-pulse re-steering capabilities that will enable some novel modes of operation. The system will nominally operate at 45,000 ft (13800 m). The program began as an Instrument Incubator Project (IIP) funded by NASA Earth Science and Technology Office (ESTO).

  14. Airborne gravity is here

    SciTech Connect

    Hammer, S.

    1982-01-11

    After 20 years of development efforts, the airborne gravity survey has finally become a practical exploration method. Besides gravity data, the airborne survey can also collect simultaneous, continuous records of high-precision magneticfield data as well as terrain clearance; these provide a topographic contour map useful in calculating terrain conditions and in subsequent planning and engineering. Compared with a seismic survey, the airborne gravity method can cover the same area much more quickly and cheaply; a seismograph could then detail the interesting spots.

  15. UAVSAR: Airborne L-Band Radar for Repeat Pass Interferometry

    NASA Technical Reports Server (NTRS)

    Moes, Tim

    2011-01-01

    The Costa Rican National Center for Advanced Technology (CeNAT) is sponsoring NASA's G-III(C-20) UAVSAR science deployment to San Jose, Costa Rica April 25-28, 2011. NASA is very thankful for their support and has offered to provide a Top-Level presentation on the G-III UAVSAR program with specific emphasis on the science conducted in Costa Rica. The presentation will overview the G-III capabilities and the various science applications of UAVSAR. Only technical and scientific data that is already in the open literature will be presented.

  16. Status of a UAVSAR designed for repeat pass interferometry for deformation measurements

    NASA Technical Reports Server (NTRS)

    Hensley, Scott; Wheeler, Kevin; Sadowy, Greg; Miller, Tim; Shaffer, Scott; Muellerschoen, Ron; Jones, Cathleen; Zebker, Howard; Madsen, Soren; Paul, Rose

    2005-01-01

    NASA's Jet Propulsion Laboratory is currently implementing a reconfigurable polarimetric L-band synthetic aperture radar (SAR), specifically designed to acquire airborne repeat track interferometric (RTI) SAR data, also known as differential interferometric measurements. Differential interferometry can provide key deformation measurements, important for the scientific studies of Earthquakes and volcanoes. Using precision real-time GPS and a sensor controlled flight management system, the system will be able to fly predefined paths with great precision. The expected performance of the flight control system will constrain the flight path to be within a 10 m diameter tube about the desired flight track. The radar wilI be designed to operate on a UAV (Unpiloted Aria1 Vehicle) but will initially be demonstrated on a minimally piloted vehicle (MPV), such as the Proteus buitt by Scaled Composites or on a NASA Gulfstream III. The radar design is a fully polarimetric with an 80 MHz bandwidth (2 m range resolution) and 16 km range swath. The antenna is an electronically steered along track to assure that the actual antenna pointing can be controlled independent of the wind direction and speed. Other features supported by the antenna include an elevation monopulse option and a pulse-to-pulse resteering capability that will enable some novel modes of operation. The system will nominally operate at 45,000 ft (13800 m). The program began out as an Instrument Incubator Project (IIP) funded by NASA Earth Science and Technology Office (ESTO).

  17. Airborne sensor integration for quick reaction programs

    NASA Astrophysics Data System (ADS)

    Gosian, Gregory; Mason, Kenneth; Servoss, Thomas; Brower, Bernard; Pellechia, Matthew

    2010-04-01

    In this paper we present an approach to integrate sensors to meet the demanding requirements of Quick Reaction Capability (QRC) airborne programs. Traditional airborne sensors are generally highly integrated and incorporate custom sensor technologies and interfaces. Custom solutions and new technologies often require significant engineering to achieve a high technology readiness level (TRL) and to meet the overall mission objective. Our approach differs from traditional approaches in that we strive to achieve an integrated solution through regular review, assessment, and identification of relevant industry "best athlete" technologies. Attention is focused on solution providers that adhere to standard interfaces and formats, incorporate non-proprietary techniques, are deemed highly-reliable/repeatable, and enable assembly production. Processes and engineering tools/methods have traditionally been applied to dozens of longer-acquisition space-based ISR programs over 50 years. We have recently leveraged these techniques to solve airborne Intelligence, Surveillance and Reconnaissance (ISR) mission challenges. This presentation describes and illustrates key aspects and examples of these techniques, solving real-world airborne mission needs.

  18. MITAS: multisensor imaging technology for airborne surveillance

    NASA Astrophysics Data System (ADS)

    Thomas, John D.

    1991-08-01

    MITAS, a unique and low-cost solution to the problem of collecting and processing multisensor imaging data for airborne surveillance operations has been developed, MITAS results from integrating the established and proven real-time video processing, target tracking, and sensor management software of TAU with commercially available image exploitation and map processing software. The MITAS image analysis station (IAS) supports airborne day/night reconnaissance and surveillance missions involving low-altitude collection platforms employing a suite of sensors to perform reconnaissance functions against a variety of ground and sea targets. The system will detect, locate, and recognize threats likely to be encountered in support of counternarcotic operations and in low-intensity conflict areas. The IAS is capable of autonomous, near real-time target exploitation and has the appropriate communication links to remotely located IAS systems for more extended analysis of sensor data. The IAS supports the collection, fusion, and processing of three main imaging sensors: daylight imagery (DIS), forward looking infrared (FLIR), and infrared line scan (IRLS). The MITAS IAS provides support to all aspects of the airborne surveillance mission, including sensor control, real-time image enhancement, automatic target tracking, sensor fusion, freeze-frame capture, image exploitation, target data-base management, map processing, remote image transmission, and report generation.

  19. Cryospheric Applications of Modern Airborne Photogrammetry

    NASA Astrophysics Data System (ADS)

    Nolan, M.

    2014-12-01

    Airborne photogrammetry is undergoing a renaissance. Lower-cost equipment, more powerful software, and simplified methods have lowered the barriers-to-entry significantly and now allow repeat-mapping of cryospheric dynamics that were previously too expensive to consider. The current state-of-the-art is the ability to use an airborne equipment package costing less than $20,000 to make topographic maps on landscape-scales at 10 cm pixel size with a vertical repeatability of about 10 cm. Nearly any surface change on the order of decimeters can be measured using these techniques through analysis of time-series of such maps. This presentation will discuss these new methods and their application to cryospheric dynamics such as the measurement of snow depth, coastal erosion, valley-glacier volume-change, permafrost thaw, frost heave of infrastructure, river bed geomorphology, and aufeis melt. Because of the expense of other airborne methods, by necessity measurements of these dynamics are currently most often made on the ground along benchmark transects that are then extrapolated to the broader scale. The ability to directly measure entire landscapes with equal or higher accuracy than transects eliminates the need to extrapolate them and the ability to do so at lower costs than transects may revolutionize the way we approach studying change in the cryosphere, as well as our understanding of the cryosphere itself.

  20. Toolsets for Airborne Data

    Atmospheric Science Data Center

    2015-04-02

    article title:  Toolsets for Airborne Data     View larger image The ... limit of detection values. Prior to accessing the TAD Web Application ( https://tad.larc.nasa.gov ) for the first time, users must ...

  1. The airborne laser

    NASA Astrophysics Data System (ADS)

    Lamberson, Steven; Schall, Harold; Shattuck, Paul

    2007-05-01

    The Airborne Laser (ABL) is an airborne, megawatt-class laser system with a state-of-the-art atmospheric compensation system to destroy enemy ballistic missiles at long ranges. This system will provide both deterrence and defense against the use of such weapons during conflicts. This paper provides an overview of the ABL weapon system including: the notional operational concept, the development approach and schedule, the overall aircraft configuration, the technologies being incorporated in the ABL, and the current program status.

  2. NASA'S Coastal and Ocean Airborne Science Testbed (COAST): Early Results

    NASA Astrophysics Data System (ADS)

    Guild, L. S.; Dungan, J. L.; Edwards, M.; Russell, P. B.; Morrow, J. H.; Kudela, R. M.; Myers, J. S.; Livingston, J.; Lobitz, B.; Torres-Perez, J.

    2012-12-01

    The NASA Coastal and Ocean Airborne Science Testbed (COAST) project advances coastal ecosystems research and ocean color calibration and validation capability by providing a unique airborne payload optimized for remote sensing in the optically complex coastal zone. The COAST instrument suite combines a customized imaging spectrometer, sunphotometer system, and a new bio-optical radiometer package to obtain ocean/coastal/atmosphere data simultaneously in flight for the first time. The imaging spectrometer (Headwall) is optimized in the blue region of the spectrum to emphasize remote sensing of marine and freshwater ecosystems. Simultaneous measurements supporting empirical atmospheric correction of image data is accomplished using the Ames Airborne Tracking Sunphotometer (AATS-14). Coastal Airborne In situ Radiometers (C-AIR, Biospherical Instruments, Inc.), developed for COAST for airborne campaigns from field-deployed microradiometer instrumentation, will provide measurements of apparent optical properties at the land/ocean boundary including optically shallow aquatic ecosystems. Ship-based measurements allowed validation of airborne measurements. Radiative transfer modeling on in-water measurements from the HyperPro and Compact-Optical Profiling System (C-OPS, the in-water companion to C-AIR) profiling systems allows for comparison of airborne and in-situ water leaving radiance measurements. Results of the October 2011 Monterey Bay COAST mission include preliminary data on coastal ocean color products, coincident spatial and temporal data on aerosol optical depth and water vapor column content, as well as derived exact water-leaving radiances.

  3. Airborne Laser-Induced Oceanic Chlorophyll Fluorescence: Solar-Induced Quenching Corrections by use of Concurrent Downwelling Irradiance Measurements

    NASA Astrophysics Data System (ADS)

    Hoge, Frank E.; Wright, C. Wayne; Swift, Robert N.; Yungel, James K.

    1998-05-01

    Airborne laser-induced (and water Raman-normalized) spectral fluorescence emissions from oceanic chlorophyll were obtained during variable downwelling irradiance conditions induced by diurnal variability and patchy clouds. Chlorophyll fluorescence profiles along geographically repeated inbound and outbound flight track lines, separated in time by 3 6 h and subject to overlying cloud movement, were found to be identical after corrections made with concurrent downwelling irradiance measurements. The corrections were accomplished by a mathematical model containing an exponential of the ratio of the instantaneous-to-average downwelling irradiance. Concurrent laser-induced phycoerythrin fluorescence and chromophoric dissolved organic matter fluorescence were found to be invariant to downwelling irradiance and thus, along with sea-surface temperature, established the near constancy of the oceanic surface layer during the experiment and validated the need for chlorophyll fluorescence quenching corrections over wide areas of the ocean.

  4. Monitoring human and vehicle activities using airborne video

    NASA Astrophysics Data System (ADS)

    Cutler, Ross; Shekhar, Chandra S.; Burns, B.; Chellappa, Rama; Bolles, Robert C.; Davis, Larry S.

    2000-05-01

    Ongoing work in Activity Monitoring (AM) for the Airborne Video Surveillance (AVS) project is described. The goal for AM is to recognize activities of interest involving humans and vehicles using airborne video. AM consists of three major components: (1) moving object detection, tracking, and classification; (2) image to site-model registration; (3) activity recognition. Detecting and tracking humans and vehicles form airborne video is a challenging problem due to image noise, low GSD, poor contrast, motion parallax, motion blur, and camera blur, and camera jitter. We use frame-to- frame affine-warping stabilization and temporally integrated intensity differences to detect independent motion. Moving objects are initially tracked using nearest-neighbor correspondence, followed by a greedy method that favors long track lengths and assumes locally constant velocity. Object classification is based on object size, velocity, and periodicity of motion. Site-model registration uses GPS information and camera/airplane orientations to provide an initial geolocation with +/- 100m accuracy at an elevation of 1000m. A semi-automatic procedure is utilized to improve the accuracy to +/- 5m. The activity recognition component uses the geolocated tracked objects and the site-model to detect pre-specified activities, such as people entering a forbidden area and a group of vehicles leaving a staging area.

  5. The Airborne Laser

    NASA Astrophysics Data System (ADS)

    Lamberson, Steven E.

    2002-09-01

    The US Air Force Airborne Laser (ABL) is an airborne, megawatt-class laser system with a state-of-the-art atmospheric compensation system to destroy enemy ballistic missiles at long ranges. This system will provide both deterrence and defense against the use of such weapons during conflicts. This paper provides an overview of the ABL weapon system including: the notional operational concept, the development approach and schedule, the overall aircraft configuration, the technologies being incorporated in the ABL, and the risk reduction approach being utilized to ensure program success.

  6. Airborne oceanographic lidar system

    NASA Technical Reports Server (NTRS)

    1975-01-01

    Specifications and preliminary design of an Airborne Oceanographic Lidar (AOL) system, which is to be constructed for installation and used on a NASA Wallops Flight Center (WFC) C-54 research aircraft, are reported. The AOL system is to provide an airborne facility for use by various government agencies to demonstrate the utility and practicality of hardware of this type in the wide area collection of oceanographic data on an operational basis. System measurement and performance requirements are presented, followed by a description of the conceptual system approach and the considerations attendant to its development. System performance calculations are addressed, and the system specifications and preliminary design are presented and discussed.

  7. NASA Airborne Lidar July 1991

    Atmospheric Science Data Center

    2016-05-26

    NASA Airborne Lidar July 1991 Data from the 1991 NASA Langley Airborne Lidar flights following the eruption of Pinatubo in July ... and Osborn [1992a, 1992b]. Project Title:  NASA Airborne Lidar Discipline:  Field Campaigns ...

  8. NASA Airborne Lidar May 1992

    Atmospheric Science Data Center

    2016-05-26

    NASA Airborne Lidar May 1992 An airborne Nd:YAG (532 nm) lidar was operated by the NASA Langley Research Center about a year following the June 1991 eruption of ... Osborn [1992a, 1992b].  Project Title:  NASA Airborne Lidar Discipline:  Field Campaigns ...

  9. Airborne antenna pattern calculations

    NASA Technical Reports Server (NTRS)

    Knerr, T. J.; Schaffner, P. R.; Mielke, R. R.; Gilreath, M. C.

    1980-01-01

    A procedure for numerically calculating radiation patterns of fuselage-mounted airborne antennas using the Volumetric Pattern Analysis Program is presented. Special attention is given to aircraft modeling. An actual case study involving a large commercial aircraft is included to illustrate the analysis procedure.

  10. Recognizing Airborne Hazards.

    ERIC Educational Resources Information Center

    Schneider, Christian M.

    1990-01-01

    The heating, ventilating, and air conditioning (HVAC) systems in older buildings often do not adequately handle air-borne contaminants. Outlines a three-stage Indoor Air Quality (IAQ) assessment and describes a case in point at a Pittsburgh, Pennsylvania, school. (MLF)

  11. Airborne Fraunhofer Line Discriminator

    NASA Technical Reports Server (NTRS)

    Gabriel, F. C.; Markle, D. A.

    1969-01-01

    Airborne Fraunhofer Line Discriminator enables prospecting for fluorescent materials, hydrography with fluorescent dyes, and plant studies based on fluorescence of chlorophyll. Optical unit design is the coincidence of Fraunhofer lines in the solar spectrum occurring at the characteristic wavelengths of some fluorescent materials.

  12. Airborne Remote Sensing

    NASA Technical Reports Server (NTRS)

    1992-01-01

    NASA imaging technology has provided the basis for a commercial agricultural reconnaissance service. AG-RECON furnishes information from airborne sensors, aerial photographs and satellite and ground databases to farmers, foresters, geologists, etc. This service produces color "maps" of Earth conditions, which enable clients to detect crop color changes or temperature changes that may indicate fire damage or pest stress problems.

  13. International Symposium on Airborne Geophysics

    NASA Astrophysics Data System (ADS)

    Mogi, Toru; Ito, Hisatoshi; Kaieda, Hideshi; Kusunoki, Kenichiro; Saltus, Richard W.; Fitterman, David V.; Okuma, Shigeo; Nakatsuka, Tadashi

    2006-05-01

    Airborne geophysics can be defined as the measurement of Earth properties from sensors in the sky. The airborne measurement platform is usually a traditional fixed-wing airplane or helicopter, but could also include lighter-than-air craft, unmanned drones, or other specialty craft. The earliest history of airborne geophysics includes kite and hot-air balloon experiments. However, modern airborne geophysics dates from the mid-1940s when military submarine-hunting magnetometers were first used to map variations in the Earth's magnetic field. The current gamut of airborne geophysical techniques spans a broad range, including potential fields (both gravity and magnetics), electromagnetics (EM), radiometrics, spectral imaging, and thermal imaging.

  14. Repeated Course Enrollments.

    ERIC Educational Resources Information Center

    Windham, Patricia

    This report resents tables of repeated course enrollment data in Florida community colleges for the fall 1993 cohort. Overall, the percent of repeats in college preparatory courses was greater than that of college credit courses. Within ICS codes, the highest percentage of credit repeat enrollments was in mathematics; the second highest was in…

  15. Handling Trajectory Uncertainties for Airborne Conflict Management

    NASA Technical Reports Server (NTRS)

    Barhydt, Richard; Doble, Nathan A.; Karr, David; Palmer, Michael T.

    2005-01-01

    Airborne conflict management is an enabling capability for NASA's Distributed Air-Ground Traffic Management (DAG-TM) concept. DAGTM has the goal of significantly increasing capacity within the National Airspace System, while maintaining or improving safety. Under DAG-TM, autonomous aircraft maintain separation from each other and from managed aircraft unequipped for autonomous flight. NASA Langley Research Center has developed the Autonomous Operations Planner (AOP), an onboard decision support system that provides airborne conflict management (ACM) and strategic flight planning support for autonomous aircraft pilots. The AOP performs conflict detection, prevention, and resolution from nearby traffic aircraft and area hazards. Traffic trajectory information is assumed to be provided by Automatic Dependent Surveillance Broadcast (ADS-B). Reliable trajectory prediction is a key capability for providing effective ACM functions. Trajectory uncertainties due to environmental effects, differences in aircraft systems and performance, and unknown intent information lead to prediction errors that can adversely affect AOP performance. To accommodate these uncertainties, the AOP has been enhanced to create cross-track, vertical, and along-track buffers along the predicted trajectories of both ownship and traffic aircraft. These buffers will be structured based on prediction errors noted from previous simulations such as a recent Joint Experiment between NASA Ames and Langley Research Centers and from other outside studies. Currently defined ADS-B parameters related to navigation capability, trajectory type, and path conformance will be used to support the algorithms that generate the buffers.

  16. [Air-borne disease].

    PubMed

    Lameiro Vilariño, Carmen; del Campo Pérez, Victor M; Alonso Bürger, Susana; Felpeto Nodar, Irene; Guimarey Pérez, Rosa; Pérez Alvarellos, Alberto

    2003-11-01

    Respiratory protection is a factor which worries nursing professionals who take care of patients susceptible of transmitting microorganisms through the air more as every day passes. This type of protection covers the use of surgical or hygienic masks against the transmission of infection by airborne drops to the use of highly effective masks or respirators against the transmission of airborne diseases such as tuberculosis or SARS, a recently discovered disease. The adequate choice of this protective device and its correct use are fundamental in order to have an effective protection for exposed personnel. The authors summarize the main protective respiratory devices used by health workers, their characteristics and degree of effectiveness, as well as the circumstances under which each device is indicated for use. PMID:14705591

  17. Efficient Object Tracking in WAAS Data Streams

    NASA Astrophysics Data System (ADS)

    Clarke, Trevor R. H.

    Wide area airborne surveillance (WAAS) systems are a new class of remote sensing imagers which have many military and civilian applications. These systems are characterized by long loiter times (extended imaging time over fixed target areas) and large footprint target areas. These characteristics complicate moving object detection and tracking due to the large image size and high number of moving objects. This thesis evaluates existing object detection and tracking algorithms with WAAS data and provides enhancements to the processing chain which decrease processing time and increase tracking accuracy. Decreases in processing time are needed to perform real-time or near real-time tracking either on the WAAS sensor platform or in ground station processing centers. Increased tracking accuracy benefits real-time users and forensic (off-line) users. The original contribution of this thesis increases tracking efficiency and accuracy by breaking a WAAS scene into hierarchical areas of interest (AOIs) and through the use of hyperspectral cueing.

  18. Airborne forest fire research

    NASA Technical Reports Server (NTRS)

    Mattingly, G. S.

    1974-01-01

    The research relating to airborne fire fighting systems is reviewed to provide NASA/Langley Research Center with current information on the use of aircraft in forest fire operations, and to identify research requirements for future operations. A literature survey, interview of forest fire service personnel, analysis and synthesis of data from research reports and independent conclusions, and recommendations for future NASA-LRC programs are included.

  19. MLS airborne antenna research

    NASA Technical Reports Server (NTRS)

    Yu, C. L.; Burnside, W. D.

    1975-01-01

    The geometrical theory of diffraction was used to analyze the elevation plane pattern of on-aircraft antennas. The radiation patterns for basic elements (infinitesimal dipole, circumferential and axial slot) mounted on fuselage of various aircrafts with or without radome included were calculated and compared well with experimental results. Error phase plots were also presented. The effects of radiation patterns and error phase plots on the polarization selection for the MLS airborne antenna are discussed.

  20. Airborne field strength monitoring

    NASA Astrophysics Data System (ADS)

    Bredemeyer, J.; Kleine-Ostmann, T.; Schrader, T.; Münter, K.; Ritter, J.

    2007-06-01

    In civil and military aviation, ground based navigation aids (NAVAIDS) are still crucial for flight guidance even though the acceptance of satellite based systems (GNSS) increases. Part of the calibration process for NAVAIDS (ILS, DME, VOR) is to perform a flight inspection according to specified methods as stated in a document (DOC8071, 2000) by the International Civil Aviation Organization (ICAO). One major task is to determine the coverage, or, in other words, the true signal-in-space field strength of a ground transmitter. This has always been a challenge to flight inspection up to now, since, especially in the L-band (DME, 1GHz), the antenna installed performance was known with an uncertainty of 10 dB or even more. In order to meet ICAO's required accuracy of ±3 dB it is necessary to have a precise 3-D antenna factor of the receiving antenna operating on the airborne platform including all losses and impedance mismatching. Introducing precise, effective antenna factors to flight inspection to achieve the required accuracy is new and not published in relevant papers yet. The authors try to establish a new balanced procedure between simulation and validation by airborne and ground measurements. This involves the interpretation of measured scattering parameters gained both on the ground and airborne in comparison with numerical results obtained by the multilevel fast multipole algorithm (MLFMA) accelerated method of moments (MoM) using a complex geometric model of the aircraft. First results will be presented in this paper.

  1. Mutagenicity of airborne particles.

    PubMed

    Chrisp, C E; Fisher, G L

    1980-09-01

    The physical and chemical properties of airborne particles are important for the interpretation of their potential biologic significance as genotoxic hazards. For polydisperse particle size distributions, the smallest, most respirable particles are generally the most mutagenic. Particulate collection for testing purposes should be designed to reduce artifact formation and allow condensation of mutagenic compounds. Other critical factors such as UV irradiation, wind direction, chemical reactivity, humidity, sample storage, and temperature of combustion are important. Application of chemical extraction methods and subsequent class fractionation techniques influence the observed mutagenic activity. Particles from urban air, coal fly ash, automobile and diesel exhaust, agricultural burning and welding fumes contain primarily direct-acting mutagens. Cigarette smoke condensate, smoke from charred meat and protein pyrolysates, kerosene soot and cigarette smoke condensates contain primarily mutagens which require metabolic activation. Fractionation coupled with mutagenicity testing indicates that the most potent mutagens are found in the acidic fractions of urban air, coal fly ash, and automobile diesel exhaust, whereas mutagens in rice straw smoke and cigarette smoke condensate are found primarily in the basic fractions. The interaction of the many chemical compounds in complex mixtures from airborne particles is likely to be important in determining mutagenic or comutagenic potentials. Because the mode of exposure is generally frequent and prolonged, the presence of tumor-promoting agents in complex mixtures may be a major factor in evaluation of the carcinogenic potential of airborne particles. PMID:7005667

  2. Airborne wireless communication systems, airborne communication methods, and communication methods

    DOEpatents

    Deaton, Juan D.; Schmitt, Michael J.; Jones, Warren F.

    2011-12-13

    An airborne wireless communication system includes circuitry configured to access information describing a configuration of a terrestrial wireless communication base station that has become disabled. The terrestrial base station is configured to implement wireless communication between wireless devices located within a geographical area and a network when the terrestrial base station is not disabled. The circuitry is further configured, based on the information, to configure the airborne station to have the configuration of the terrestrial base station. An airborne communication method includes answering a 911 call from a terrestrial cellular wireless phone using an airborne wireless communication system.

  3. Evolution of the SOFIA tracking control system

    NASA Astrophysics Data System (ADS)

    Fiebig, Norbert; Jakob, Holger; Pfüller, Enrico; Röser, Hans-Peter; Wiedemann, Manuel; Wolf, Jürgen

    2014-07-01

    The airborne observatory SOFIA (Stratospheric Observatory for Infrared Astronomy) is undergoing a modernization of its tracking system. This included new, highly sensitive tracking cameras, control computers, filter wheels and other equipment, as well as a major redesign of the control software. The experiences along the migration path from an aged 19" VMbus based control system to the application of modern industrial PCs, from VxWorks real-time operating system to embedded Linux and a state of the art software architecture are presented. Further, the concept is presented to operate the new camera also as a scientific instrument, in parallel to tracking.

  4. Airborne Submillimeter Spectroscopy

    NASA Technical Reports Server (NTRS)

    Zmuidzinas, J.

    1998-01-01

    This is the final technical report for NASA-Ames grant NAG2-1068 to Caltech, entitled "Airborne Submillimeter Spectroscopy", which extended over the period May 1, 1996 through January 31, 1998. The grant was funded by the NASA airborne astronomy program, during a period of time after the Kuiper Airborne Observatory was no longer operational. Instead. this funding program was intended to help develop instrument concepts and technology for the upcoming SOFIA (Stratospheric Observatory for Infrared Astronomy) project. SOFIA, which is funded by NASA and is now being carried out by a consortium lead by USRA (Universities Space Research Association), will be a 747 aircraft carrying a 2.5 meter diameter telescope. The purpose of our grant was to fund the ongoing development of sensitive heterodyne receivers for the submillimeter band (500-1200 GHz), using sensitive superconducting (SIS) detectors. In 1997 July we submitted a proposal to USRA to construct a heterodyne instrument for SOFIA. Our proposal was successful [1], and we are now continuing our airborne astronomy effort with funding from USRA. A secondary purpose of the NAG2-1068 grant was to continue the anaIN'sis of astronomical data collected with an earlier instrument which was flown on the NASA Kuiper Airborne Observatory (KAO). The KAO instrument and the astronomical studies which were carried out with it were supported primarily under another grant, NAG2-744, which extended over October 1, 1991 through Januarv 31, 1997. For a complete description of the astronomical data and its anailysis, we refer the reader to the final technical report for NAG2-744, which was submitted to NASA on December 1. 1997. Here we report on the SIS detector development effort for SOFIA carried out under NAG2-1068. The main result of this effort has been the demonstration of SIS mixers using a new superconducting material niobium titanium nitride (NbTiN), which promises to deliver dramatic improvements in sensitivity in the 700

  5. Calibration of airborne SAR interferograms using multisquint-processed image pairs

    NASA Astrophysics Data System (ADS)

    Prats, Pau; Mallorqui, Jordi J.; Reigber, Andreas; Broquetas, Antoni

    2004-01-01

    This paper presents two different approaches to detect and correct phase errors appearing in interferometric airborne SAR sensors due to the lack of precision in the navigation system. The first one is intended for interferometric pairs with high coherence, and the second one for low coherent ones. Both techniques are based on a multisquint processing approach, i.e., by processing the same image pairs with different squint angles we can combine the information of different interferograms to obtain the desired phase correction. Airborne single- and repeat-pass interferometric data from the Deutsches Zentrum fur Luft- und Raumfahrt (DLR) Experimental airborne SAR is used to validate the method.

  6. Using Airborne Laser Altimetry to Detect Topographic Change at Long Valley Caldera California

    NASA Technical Reports Server (NTRS)

    Hofton, M. A.; Minster, J.-B.; Ridgway, J. R.; Williams, N. P.; Blair, J. B.; Rabine, D. L.; Bufton, J. L.

    2000-01-01

    The topography of the Long Valley caldera, California, was sampled using airborne laser altimetry in 1993, 1995, and 1997 to test the feasibility of using airborne laser altimetry for monitoring deformation of volcanic origin. Results show the laser altimeters are able to resolve subtle topographic features such as a gradual slope and to detect small transient changes in lake elevation. Crossover and repeat pass analyses of laser tracks indicate decimeter-level vertical precision is obtained over flat and low-sloped terrain for altimeter systems performing waveform digitization. Comparisons with complementary, ground-based CPS data at a site close to Bishop airport indicate that the laser and GPS-derived elevations agree to within the error inherent in the measurement and that horizontal locations agree to within the radius of the laser footprint. A comparison of the data at two sites, one where no change and the other where the maximum amount of vertical uplift is expected, indicates approximately 10 cm of relative uplift occurred 1993-1997, in line with predictions from continuous CPS measurements in the region. Extensive terrain mapping flights during the 1995 and 1997 missions demonstrate some of the unique abilities of laser altimetry; the straightforward creation of high resolution, high accuracy digital elevation models of overflown terrain, and the ability to determine ground topography in the presence of significant ground cover such as dense tree canopies. These capabilities make laser altimetry an attractive technique for quantifying topographic change of volcanic origin, especially in forested regions of the world where other remote sensing instruments have difficulty detecting the underlying topography.

  7. Using Airborne Laser Altimetry to Detect Topographic Change at Long Valley Caldera, California

    NASA Technical Reports Server (NTRS)

    Hofton, M. A.; Minster, J.-B.; Ridgway, J. R.; Williams, N. P.; Blair, J.-B.; Rabine, D. L.; Bufton, J. L.

    1999-01-01

    The topography of the Long Valley caldera, California, was sampled using airborne laser altimetry in 1993, 1995, and 1997 to test the feasibility of using airborne laser altimetry for monitoring deformation of volcanic origin. Results show the laser altimeters are able to resolve subtle topographic features such as a gradual slope and to detect small transient changes in lake elevation. Crossover and repeat pass analyses of laser tracks indicate decimeter-level vertical precision is obtained over flat and low-sloped terrain for altimeter systems performing waveform digitization. Comparisons with complementary, ground-based GPS data at a site close to Bishop airport indicate that the laser and GPS-derived elevations agree to within the error inherent in the measurement and that horizontal locations agree to within the radius of the laser footprint. A comparison of the data at two sites, one where no change and the other where the maximum amount of vertical uplift is expected, indicates approximately 10 cm of relative uplift occurred 1993-1997, in line with predictions from continuous GPS measurements in the region. Extensive terrain mapping flights during the 1995 and 1997 missions demonstrate some of the unique abilities of laser altimetry; the straightforward creation of high resolution, high accuracy digital elevation models of overflown terrain, and the ability to determine ground topography in the presence of significant ground cover such as dense tree canopies. These capabilities make laser altimetry an attractive technique for quantifying topographic change of volcanic origin, especially in forested regions of the world where other remote sensing instruments have difficulty detecting the underlying topography.

  8. Migration of Contaminated Soil and Airborne Particulates to Indoor Dust

    PubMed Central

    Layton, David W.; Beamer, Paloma I.

    2009-01-01

    We have developed a modeling and measurement framework for assessing transport of contaminated soils and airborne particulates into a residence, their subsequent distribution indoors via resuspension and deposition processes, and removal by cleaning and building exhalation of suspended particles. The model explicitly accounts for the formation of house dust as a mixture of organic matter (OM) such as shed skin cells and organic fibers, soil tracked-in on footwear, and particulate matter (PM) derived from the infiltration of outdoor air. We derived formulas for use with measurements of inorganic contaminants, crustal tracers, OM, and PM to quantify selected transport parameters. Application of the model to residences in the U.S. Midwest indicates that As in ambient air can account for nearly 60% of the As input to floor dust, with soil track-in representing the remainder. Historic data on Pb contamination in Sacramento, CA, was used to reconstruct sources of Pb in indoor dust, showing that airborne Pb was likely the dominant source in the early 1980s. However, as airborne Pb levels declined due to the phase out of leaded gasoline, soil resuspension and track-in eventually became the primary sources of Pb in house dust. PMID:19924944

  9. PHARUS airborne SAR concept

    NASA Astrophysics Data System (ADS)

    Snoeij, Paul; Pouwels, Henk; Koomen, Peter J.; Hoogeboom, Peter

    1995-11-01

    PHARUS (phased array universal SAR) is an airborne SAR concept which is being developed in the Netherlands. The PHARUS system differs from other airborne SARs by the use of a phased array antenna, which provides both for the flexibility in the design as well as for a compact, light-weight instrument that can be carried on small aircraft. The concept allows for the construction of airborne SAR systems on a common generic basis but tailored to specific user needs and can be seen as a preparation for future spaceborne SAR systems using solid state transmitters with electronically steerable phased array antenna. The whole approach is aimed at providing an economic and yet technically sophisticated solution to remote sensing or surveying needs of a specific user. The solid state phased array antenna consists of a collection of radiating patches; the design flexibility for a large part resides in the freedom to choose the number of patches, and thereby the essential radar performance parameters such as resolution and swath width. Another consequence of the use of the phased array antenna is the system's compactness and the possibility to rigidly mount it on a small aircraft. The use of small aircraft of course considerably improves the cost/benefit ratio of the use of airborne SAR. Flight altitude of the system is flexible between about 7,000 and 40,000 feet, giving much operational freedom within the meteo and airspace control limits. In the PHARUS concept the airborne segment is complemented by a ground segment, which consists of a SAR processor, possibly extended by a matching image processing package. (A quick look image is available in real-time on board the aircraft.) The SAR processor is UNIX based and runs on easily available hardware (SUN station). Although the additional image processing software is available, the SAR processing software is nevertheless designed to be able to interface with commercially available image processing software, as well as being able

  10. Airborne radioactive contamination monitoring

    SciTech Connect

    Whitley, C.R.; Adams, J.R.; Bounds, J.A.; MacArthur, D.W.

    1996-03-01

    Current technologies for the detection of airborne radioactive contamination do not provide real-time capability. Most of these techniques are based on the capture of particulate matter in air onto filters which are then processed in the laboratory; thus, the turnaround time for detection of contamination can be many days. To address this shortcoming, an effort is underway to adapt LRAD (Long-Range-Alpha-Detection) technology for real-time monitoring of airborne releases of alpa-emitting radionuclides. Alpha decays in air create ionization that can be subsequently collected on electrodes, producing a current that is proportional to the amount of radioactive material present. Using external fans on a pipe containing LRAD detectors, controlled samples of ambient air can be continuously tested for the presence of radioactive contamination. Current prototypes include a two-chamber model. Sampled air is drawn through a particulate filter and then through the first chamber, which uses an electrostatic filter at its entrance to remove ambient ionization. At its exit, ionization that occurred due to the presence of radon is collected and recorded. The air then passes through a length of pipe to allow some decay of short-lived radon species. A second chamber identical to the first monitors the remaining activity. Further development is necessary on air samples without the use of particulate filtering, both to distinguish ionization that can pass through the initial electrostatic filter on otherwise inert particulate matter from that produced through the decay of radioactive material and to separate both of these from the radon contribution. The end product could provide a sensitive, cost-effective, real-time method of determining the presence of airborne radioactive contamination.

  11. Use of Airborne Thermal Imagery to Detect and Monitor Inshore Oil Spill Residues During Darkness Hours.

    PubMed

    GRIERSON

    1998-11-01

    / Trials were conducted using an airborne video system operating in the visible, near-infrared, and thermal wavelengths to detect two known oil spill releases during darkness at a distance of 10 nautical miles from the shore in St. Vincent's Gulf, South Australia. The oil spills consisted of two 20-liter samples released at 2-h intervals, one sample consisted of paraffinic neutral material and the other of automotive diesel oil. A tracking buoy was sent overboard in conjunction with the release of sample 1, and its movement monitored by satellite relay. Both oil residues were overflown by a light aircraft equipped with thermal, visible, and infrared imagers at a period of approximately 1 h after the release of the second oil residue. Trajectories of the oil residue releases were also modeled and the results compared to those obtained by the airborne video and the tracking buoy. Airborne imagery in the thermal wavelengths successfully located and mapped both oil residue samples during nighttime conditions. Results from the trial suggest that the most advantageous technique would be the combined use of the tracking beacon to obtain an approximate location of the oil spill and the airborne imagery to ascertain its extent and characteristics.KEY WORDS: Airborne video; Thermal imagery; Global positioning; Oil-spill monitoring; Tracking beacon PMID:9732519

  12. Airborne Raman lidar

    NASA Astrophysics Data System (ADS)

    Heaps, Wm. S.; Burris, J.

    1996-12-01

    We designed and tested an airborne lidar system using Raman scattering to make simultaneous measurements of methane, water vapor, and temperature in a series of flights on a NASA-operated C-130 aircraft. We present the results for methane detection, which show that the instrument has the requisite sensitivity to atmospheric trace gases. Ultimately these measurements can be used to examine the transport of chemically processed air from within the polar vortex to mid-latitudinal regions and the exchange of stratospheric air between tropical and mid-latitudinal regions.

  13. Airborne Oceanographic Lidar System

    NASA Technical Reports Server (NTRS)

    Bressel, C.; Itzkan, I.; Nunes, J. E.; Hoge, F.

    1977-01-01

    The Airborne Oceanographic Lidar (AOL), a spatially scanning range-gated device installed on board a NASA C-54 aircraft, is described. The AOL system is capable of measuring topographical relief or water depth (bathymetry) with a range resolution of plus or minus 0.3 m in the vertical dimension. The system may also be used to measure fluorescent spectral signatures from 3500 to 8000 A with a resolution of 100 A. Potential applications of the AOL, including sea state measurements, water transparency assessments, oil spill identification, effluent identification and crop cover assessment are also mentioned.

  14. The NRL 2011 Airborne Sea-Ice Thickness Campaign

    NASA Astrophysics Data System (ADS)

    Brozena, J. M.; Gardner, J. M.; Liang, R.; Ball, D.; Richter-Menge, J.

    2011-12-01

    In March of 2011, the US Naval Research Laboratory (NRL) performed a study focused on the estimation of sea-ice thickness from airborne radar, laser and photogrammetric sensors. The study was funded by ONR to take advantage of the Navy's ICEX2011 ice-camp /submarine exercise, and to serve as a lead-in year for NRL's five year basic research program on the measurement and modeling of sea-ice scheduled to take place from 2012-2017. Researchers from the Army Cold Regions Research and Engineering Laboratory (CRREL) and NRL worked with the Navy Arctic Submarine Lab (ASL) to emplace a 9 km-long ground-truth line near the ice-camp (see Richter-Menge et al., this session) along which ice and snow thickness were directly measured. Additionally, US Navy submarines collected ice draft measurements under the groundtruth line. Repeat passes directly over the ground-truth line were flown and a grid surrounding the line was also flown to collect altimeter, LiDAR and Photogrammetry data. Five CRYOSAT-2 satellite tracks were underflown, as well, coincident with satellite passage. Estimates of sea ice thickness are calculated assuming local hydrostatic balance, and require the densities of water, ice and snow, snow depth, and freeboard (defined as the elevation of sea ice, plus accumulated snow, above local sea level). Snow thickness is estimated from the difference between LiDAR and radar altimeter profiles, the latter of which is assumed to penetrate any snow cover. The concepts we used to estimate ice thickness are similar to those employed in NASA ICEBRIDGE sea-ice thickness estimation. Airborne sensors used for our experiment were a Reigl Q-560 scanning topographic LiDAR, a pulse-limited (2 nS), 10 GHz radar altimeter and an Applanix DSS-439 digital photogrammetric camera (for lead identification). Flights were conducted on a Twin Otter aircraft from Pt. Barrow, AK, and averaged ~ 5 hours in duration. It is challenging to directly compare results from the swath LiDAR with the

  15. Airborne concentrations of peanut protein.

    PubMed

    Johnson, Rodney M; Barnes, Charles S

    2013-01-01

    Food allergy to peanut is a significant health problem, and there are reported allergic reactions to peanuts despite not eating or having physical contact with peanuts. It is presumed that an allergic reaction may have occurred from inhalation of airborne peanut allergens. The purpose of this study was to detect the possible concentrations of airborne peanut proteins for various preparations and during specific activities. Separate Ara h 1 and Ara h 2 monoclonal enzyme-linked immunosorbent assays and a polyclonal sandwich enzyme immunoassay for peanuts were used to detect the amount of airborne peanut protein collected using a Spincon Omni 3000 air collector (Sceptor Industries, Inc., Kansas City, MO) under different peanut preparation methods and situations. Air samples were measured for multiple peanut preparations and scenarios. Detectable amounts of airborne peanut protein were measured using a whole peanut immunoassay when removing the shells of roasted peanut. No airborne peanut allergen (Ara h 1 or Ara h 2) or whole peanut protein above the LLD was measured in any of the other peanut preparation collections. Ara h 1, Ara h 2, and polyclonal peanut proteins were detected from water used to boil peanuts. Small amounts of airborne peanut protein were detected in the scenario of removing shells from roasted peanuts; however, Ara h 1 and Ara h 2 proteins were unable to be consistently detected. Although airborne peanut proteins were detected, the concentration of airborne peanut protein that is necessary to elicit a clinical allergic reaction is unknown. PMID:23406937

  16. Derailing Tracking.

    ERIC Educational Resources Information Center

    Black, Susan

    1993-01-01

    Reviews recent research on student achievement, self-concept, and curriculum and instruction showing the ineffectiveness of tracking and ability grouping. Certain court rulings show that tracking violates the equal protection clause of the Fourteenth Amendment. Innovative alternatives include cooperative learning, mastery learning, peer tutoring,…

  17. Beyond Tracking.

    ERIC Educational Resources Information Center

    Bates, Percy; And Others

    1992-01-01

    On the surface, educational tracking may seem like a useful tool for allowing students to work at their own pace, and to avoid discouraging competition, but abuses of the tracking idea have arisen through biased placement practices that have denied equal access to education for minority students. The articles in this issue explore a number of…

  18. Airborne transmission of lyssaviruses.

    PubMed

    Johnson, N; Phillpotts, R; Fooks, A R

    2006-06-01

    In 2002, a Scottish bat conservationist developed a rabies-like disease and subsequently died. This was caused by infection with European bat lyssavirus 2 (EBLV-2), a virus closely related to Rabies virus (RABV). The source of this infection and the means of transmission have not yet been confirmed. In this study, the hypothesis that lyssaviruses, particularly RABV and the bat variant EBLV-2, might be transmitted via the airborne route was tested. Mice were challenged via direct introduction of lyssavirus into the nasal passages. Two hours after intranasal challenge with a mouse-adapted strain of RABV (Challenge Virus Standard), viral RNA was detectable in the tongue, lungs and stomach. All of the mice challenged by direct intranasal inoculation developed disease signs by 7 days post-infection. Two out of five mice challenged by direct intranasal inoculation of EBLV-2 developed disease between 16 and 19 days post-infection. In addition, a simple apparatus was evaluated in which mice could be exposed experimentally to infectious doses of lyssavirus from an aerosol. Using this approach, mice challenged with RABV, but not those challenged with EBLV-2, were highly susceptible to infection by inhalation. These data support the hypothesis that lyssaviruses, and RABV in particular, can be spread by airborne transmission in a dose-dependent manner. This could present a particular hazard to personnel exposed to aerosols of infectious RABV following accidental release in a laboratory environment. PMID:16687600

  19. Reconfigurable multiport EPON repeater

    NASA Astrophysics Data System (ADS)

    Oishi, Masayuki; Inohara, Ryo; Agata, Akira; Horiuchi, Yukio

    2009-11-01

    An extended reach EPON repeater is one of the solutions to effectively expand FTTH service areas. In this paper, we propose a reconfigurable multi-port EPON repeater for effective accommodation of multiple ODNs with a single OLT line card. The proposed repeater, which has multi-ports in both OLT and ODN sides, consists of TRs, BTRs with the CDR function and a reconfigurable electrical matrix switch, can accommodate multiple ODNs to a single OLT line card by controlling the connection of the matrix switch. Although conventional EPON repeaters require full OLT line cards to accommodate subscribers from the initial installation stage, the proposed repeater can dramatically reduce the number of required line cards especially when the number of subscribers is less than a half of the maximum registerable users per OLT. Numerical calculation results show that the extended reach EPON system with the proposed EPON repeater can save 17.5% of the initial installation cost compared with a conventional repeater, and can be less expensive than conventional systems up to the maximum subscribers especially when the percentage of ODNs in lightly-populated areas is higher.

  20. Revisiting the TALE repeat.

    PubMed

    Deng, Dong; Yan, Chuangye; Wu, Jianping; Pan, Xiaojing; Yan, Nieng

    2014-04-01

    Transcription activator-like (TAL) effectors specifically bind to double stranded (ds) DNA through a central domain of tandem repeats. Each TAL effector (TALE) repeat comprises 33-35 amino acids and recognizes one specific DNA base through a highly variable residue at a fixed position in the repeat. Structural studies have revealed the molecular basis of DNA recognition by TALE repeats. Examination of the overall structure reveals that the basic building block of TALE protein, namely a helical hairpin, is one-helix shifted from the previously defined TALE motif. Here we wish to suggest a structure-based re-demarcation of the TALE repeat which starts with the residues that bind to the DNA backbone phosphate and concludes with the base-recognition hyper-variable residue. This new numbering system is consistent with the α-solenoid superfamily to which TALE belongs, and reflects the structural integrity of TAL effectors. In addition, it confers integral number of TALE repeats that matches the number of bound DNA bases. We then present fifteen crystal structures of engineered dHax3 variants in complex with target DNA molecules, which elucidate the structural basis for the recognition of bases adenine (A) and guanine (G) by reported or uncharacterized TALE codes. Finally, we analyzed the sequence-structure correlation of the amino acid residues within a TALE repeat. The structural analyses reported here may advance the mechanistic understanding of TALE proteins and facilitate the design of TALEN with improved affinity and specificity. PMID:24622844

  1. Quantum repeated games revisited

    NASA Astrophysics Data System (ADS)

    Frąckiewicz, Piotr

    2012-03-01

    We present a scheme for playing quantum repeated 2 × 2 games based on Marinatto and Weber’s approach to quantum games. As a potential application, we study the twice repeated Prisoner’s Dilemma game. We show that results not available in the classical game can be obtained when the game is played in the quantum way. Before we present our idea, we comment on the previous scheme of playing quantum repeated games proposed by Iqbal and Toor. We point out the drawbacks that make their results unacceptable.

  2. Load tracking and structural health monitoring of unmanned aerial vehicles using optical fiber sensors

    NASA Astrophysics Data System (ADS)

    Handelman, A.; Botsev, Y.; Balter, J.; Gud's, P.; Kressel, I.; Tur, M.; Gali, S.; Pillai, A. C. R.; Hari Prasad, M.; Yadav, A. Kumar; Gupta, Nitesh; Sathya, Sakthi; Sundaram, Ramesh

    2011-08-01

    An airborne, high resolution, load tracking and structural health monitoring system for unmanned aerial vehicles is presented. The system is based on embedded optical fiber Bragg sensors interrogated in real time during flight at 2.5 kHz. By analyzing the recorded vibration signature it is now possible to identify and trace the dynamic response of an airborne structure and track its loads.

  3. Load tracking and structural health monitoring of unmanned aerial vehicles using optical fiber sensors

    NASA Astrophysics Data System (ADS)

    Handelman, A.; Botsev, Y.; Balter, J.; Gud'S, P.; Kressel, I.; Tur, M.; Gali, S.; Pillai, A. C. R.; Hari Prasad, M.; Yadav, A. Kumar; Gupta, Nitesh; Sathya, Sakthi; Sundaram, Ramesh

    2010-12-01

    An airborne, high resolution, load tracking and structural health monitoring system for unmanned aerial vehicles is presented. The system is based on embedded optical fiber Bragg sensors interrogated in real time during flight at 2.5 kHz. By analyzing the recorded vibration signature it is now possible to identify and trace the dynamic response of an airborne structure and track its loads.

  4. AESMIR: A New NASA Airborne Microwave Imager

    NASA Technical Reports Server (NTRS)

    Kim, Edward J.; Hood, Robbie; Hildebrand, Peter H. (Technical Monitor)

    2001-01-01

    The Airborne Earth Science Microwave Imaging Radiometer (AESMIR) is a versatile new airborne imaging radiometer under development by NASA. The AESMIR design is unique in that it will perform dual-polarized imaging at all AMSR frequency bands (6.9 through 89 GHz) using only one sensor head/scanner package, providing an efficient solution for AMSR-type science applications (snow, soil moisture/land parameters, precip, ocean winds, SST, water vapor, sea ice, etc.). The microwave radiometers themselves will incorporate state-of-the-art receivers, with particular attention given to instrument calibration for the best possible accuracy and sensitivity. The single-package design of AESMIR makes it compatible with high-altitude aircraft platforms such as the NASA ER-2s and the Proteus. The arbitrary 2-axis gimbal can perform conical and cross-track scanning, as well as fixed-beam staring. This compatibility with high-altitude platforms coupled with the flexible scanning configuration, opens up previously unavailable science opportunities for convection/precip/cloud science and co-flying with complementary instruments, as well as providing wider swath coverage for all science applications. By designing AESMIR to be compatible with these high-altitude platforms, we are also compatible with the NASA P-3, the NASA DC-8, and ground-based deployments. Thus AESMIR can provide low-, mid-, and high altitude microwave imaging.

  5. CALIOPE and TAISIR airborne experiment platform

    SciTech Connect

    Chocol, C.J.

    1994-07-01

    Between 1950 and 1970, scientific ballooning achieved many new objectives and made a substantial contribution to understanding near-earth and space environments. In 1986, the Lawrence Livermore National Laboratory (LLNL) began development of ballooning technology capable of addressing issues associated with precision tracking of ballistic missiles. In 1993, the Radar Ocean Imaging Project identified the need for a low altitude (1 km) airborne platform for its Radar system. These two technologies and experience base have been merged with the acquisition of government surplus Aerostats by Lawrence Livermore National Laboratory. The CALIOPE and TAISIR Programs can benefit directly from this technology by using the Aerostat as an experiment platform for measurements of the spill facility at NTS.

  6. Rover tracks

    NASA Technical Reports Server (NTRS)

    1997-01-01

    Tracks made by the Sojourner rover are visible in this image, taken by one of the cameras aboard Sojourner on Sol 3. The tracks represent the rover maneuvering towards the rock dubbed 'Barnacle Bill.' The rover, having exited the lander via the rear ramp, first traveled towards the right portion of the image, and then moved forward towards the left where Barnacle Bill sits. The fact that the rover was making defined tracks indicates that the soil is made up of particles on a micron scale.

    Mars Pathfinder was developed and managed by the Jet Propulsion Laboratory (JPL) for the National Aeronautics and Space Administration.

  7. Processor architecture for airborne SAR systems

    NASA Technical Reports Server (NTRS)

    Glass, C. M.

    1983-01-01

    Digital processors for spaceborne imaging radars and application of the technology developed for airborne SAR systems are considered. Transferring algorithms and implementation techniques from airborne to spaceborne SAR processors offers obvious advantages. The following topics are discussed: (1) a quantification of the differences in processing algorithms for airborne and spaceborne SARs; and (2) an overview of three processors for airborne SAR systems.

  8. Evaluation of meteorological airborne Doppler radar

    NASA Technical Reports Server (NTRS)

    Hildebrand, P. H.; Mueller, C. K.

    1984-01-01

    This paper will discuss the capabilities of airborne Doppler radar for atmospheric sciences research. The evaluation is based on airborne and ground based Doppler radar observations of convective storms. The capability of airborne Doppler radar to measure horizontal and vertical air motions is evaluated. Airborne Doppler radar is shown to be a viable tool for atmospheric sciences research.

  9. Airborne agent concentration analysis

    DOEpatents

    Gelbard, Fred

    2004-02-03

    A method and system for inferring airborne contaminant concentrations in rooms without contaminant sensors, based on data collected by contaminant sensors in other rooms of a building, using known airflow interconnectivity data. The method solves a least squares problem that minimizes the difference between measured and predicted contaminant sensor concentrations with respect to an unknown contaminant release time. Solutions are constrained to providing non-negative initial contaminant concentrations in all rooms. The method can be used to identify a near-optimal distribution of sensors within the building, when then number of available sensors is less than the total number of rooms. This is achieved by having a system-sensor matrix that is non-singular, and by selecting that distribution which yields the lowest condition number of all the distributions considered. The method can predict one or more contaminant initial release points from the collected data.

  10. Airborne Wind Turbine

    SciTech Connect

    2010-09-01

    Broad Funding Opportunity Announcement Project: Makani Power is developing an Airborne Wind Turbine (AWT) that eliminates 90% of the mass of a conventional wind turbine and accesses a stronger, more consistent wind at altitudes of near 1,000 feet. At these altitudes, 85% of the country can offer viable wind resources compared to only 15% accessible with current technology. Additionally, the Makani Power wing can be economically deployed in deep offshore waters, opening up a resource which is 4 times greater than the entire U.S. electrical generation capacity. Makani Power has demonstrated the core technology, including autonomous launch, land, and power generation with an 8 meter wingspan, 20 kW prototype. At commercial scale, Makani Power aims to develop a 600 kW, 28 meter wingspan product capable of delivering energy at an unsubsidized cost competitive with coal, the current benchmark for low-cost power.

  11. Airborne Cloud Computing Environment (ACCE)

    NASA Technical Reports Server (NTRS)

    Hardman, Sean; Freeborn, Dana; Crichton, Dan; Law, Emily; Kay-Im, Liz

    2011-01-01

    Airborne Cloud Computing Environment (ACCE) is JPL's internal investment to improve the return on airborne missions. Improve development performance of the data system. Improve return on the captured science data. The investment is to develop a common science data system capability for airborne instruments that encompasses the end-to-end lifecycle covering planning, provisioning of data system capabilities, and support for scientific analysis in order to improve the quality, cost effectiveness, and capabilities to enable new scientific discovery and research in earth observation.

  12. Research on the error model of airborne celestial/inertial integrated navigation system

    NASA Astrophysics Data System (ADS)

    Zheng, Xiaoqiang; Deng, Xiaoguo; Yang, Xiaoxu; Dong, Qiang

    2015-02-01

    Celestial navigation subsystem of airborne celestial/inertial integrated navigation system periodically correct the positioning error and heading drift of the inertial navigation system, by which the inertial navigation system can greatly improve the accuracy of long-endurance navigation. Thus the navigation accuracy of airborne celestial navigation subsystem directly decides the accuracy of the integrated navigation system if it works for long time. By building the mathematical model of the airborne celestial navigation system based on the inertial navigation system, using the method of linear coordinate transformation, we establish the error transfer equation for the positioning algorithm of airborne celestial system. Based on these we built the positioning error model of the celestial navigation. And then, based on the positioning error model we analyze and simulate the positioning error which are caused by the error of the star tracking platform with the MATLAB software. Finally, the positioning error model is verified by the information of the star obtained from the optical measurement device in range and the device whose location are known. The analysis and simulation results show that the level accuracy and north accuracy of tracking platform are important factors that limit airborne celestial navigation systems to improve the positioning accuracy, and the positioning error have an approximate linear relationship with the level error and north error of tracking platform. The error of the verification results are in 1000m, which shows that the model is correct.

  13. Imaging fault slip variation along the central San Andreas fault from satellite, airborne InSAR and GPS

    NASA Astrophysics Data System (ADS)

    Liu, Z.; Lundgren, P.; Fielding, E. J.; Hensley, S.

    2011-12-01

    The improved spatiotemporal resolution of surface deformation from recent satellite and airborne InSAR measurements provides great potential to improve our understanding of faulting processes and earthquake hazard for a given fault system. A major plate boundary fault in central California, the central San Andreas fault (CSAF) displays a spectrum of complex fault slip behaviors with creeping in its central segment that decreases towards its northwest and southeast ends where the fault transitions to being locked. In the north the CSAF branches into two sub-parallel faults that are both actively accommodating plate motion. To the south, near the Parkfield transition, large earthquakes have occurred with at least six Mw ~6.0 events since 1857, most recently in 2004. To understand the complexity and variety of fault slip behaviors and fault mechanics, we integrate satellite and airborne synthetic aperture radar (SAR) repeat pass interferometry (RPI) observations, with GPS measurements from the Plate Boundary Observatory (PBO) and regional campaign networks to estimate fault slip and shallow slip deficits along the CSAF. Existing C-band ERS-1/2, Envisat and Radarsat SAR data provide long archives of SAR data over the region but are subject to severe decorrelation. The Japan Aerospace Exploration Agency's ALOS satellite has made less frequent acquisitions (5-6/yr per track) since 2006 but its PALSAR L-band sensor provides much improved coherence compared to shorter wavelength radar data. More recently, the NASA UAVSAR airborne SAR has repeated fault perpendicular adjacent swaths imaged from opposing look directions and fault parallel swath flights over the CSAF over the past three years and provides an improved imaging of fault slip related deformation at finer spatial resolution than previous platforms (~6m at 12 azimuth x 3 range looks). Compared to C-band instruments, the UAVSAR provides nearly complete spatial coverage. Compared to the ALOS mission, the UAVSAR

  14. Airborne Remote Sensing of River Flow and Morphology

    NASA Astrophysics Data System (ADS)

    Zuckerman, S.; Anderson, S. P.; McLean, J.; Redford, R.

    2014-12-01

    River morphology, surface slope and flow are some of the fundamental measurements required for surface water monitoring and hydrodynamic research. This paper describes a method of combining bathymetric lidar with space-time processing of mid-wave infrared (MWIR) imagery to simultaneously measure bathymetry, currents and surface slope from an airborne platform. In May 2014, Areté installed a Pushbroom Imaging Lidar for Littoral Surveillance (PILLS) and a FLIR SC8000 MWIR imaging system sampling at 2 Hz in a small twin-engine aircraft. Data was collected over the lower Colorado River between Picacho Park and Parker. PILLS is a compact bathymetric lidar based on streak-tube sensor technology. It provides channel and bank topography and water surface elevation at 1 meter horizontal scales and 25 cm vertical accuracy. Surface currents are derived from the MWIR imagery by tracking surface features using a cross correlation algorithm. This approach enables the retrieval of currents along extended reaches at the forward speed of the aircraft with spatial resolutions down to 5 m with accuracy better than 10 cm/s. The fused airborne data captures current and depth variability on scales of meters over 10's of kilometers collected in just a few minutes. The airborne MWIR current retrievals are combined with the bathymetric lidar data to calculate river discharge which is then compared with real-time streamflow stations. The results highlight the potential for improving our understanding of complex river environments with simultaneous collections from multiple airborne sensors.

  15. Profiling the atmosphere with the airborne radio occultation technique

    NASA Astrophysics Data System (ADS)

    Muradyan, Paytsar

    The GNSS Instrument System for Multistatic and Occultation Sensing (GISMOS) was designed for dense sampling of meteorological targets using the airborne radio occultation (RO) technique. Airborne RO refers to an atmospheric limb sounding technique in which Global Positioning System (GPS) signals are recorded at a receiver onboard an aircraft as the satellites descend beyond the limb of the Earth. The GPS signals, that are unaffected by clouds and precipitation, experience refractive bending as well as a delay in the travel time through the atmosphere. Bending can be used to retrieve information about atmospheric refractivity, which depends on atmospheric moisture and temperature. The new system has the potential for improving numerical weather prediction (NWP) forecasts through assimilation of many high-resolution atmospheric profiles in an area of interest, compared to spaceborne RO, which samples sparsely around the globe. In February 2008, GISMOS was deployed on the National Science Foundation Gulfstream-V aircraft to make atmospheric observations in the Gulf of Mexico coastal region with an objective to test the performance of the profiling system. Recordings from this flight campaign made with the conventional phase lock loop GPS receivers descend from flight level to 5 km altitude. However, below that level strong refractivity gradients, especially those associated with the boundary layer, cause rapid phase accelerations resulting in loss of lock in the receiver. To extend the RO profiles deeper in the atmosphere, the GISMOS system was also equipped with a GPS Recording System (GRS) that records the raw RF signals. Post-processing this dataset in open-loop (OL) tracking mode enables reliable atmospheric profiling at lower altitudes. We present a comprehensive analysis of the performance of the airborne system OL tracking algorithm during a 5 hour flight on 15 February 2008. Excess phase and amplitude profiles for 5 setting and 5 rising occultations were

  16. The Pentapeptide Repeat Proteins

    SciTech Connect

    Vetting,M.; Hegde, S.; Fajardo, J.; Fiser, A.; Roderick, S.; Takiff, H.; Blanchard, J.

    2006-01-01

    The Pentapeptide Repeat Protein (PRP) family has over 500 members in the prokaryotic and eukaryotic kingdoms. These proteins are composed of, or contain domains composed of, tandemly repeated amino acid sequences with a consensus sequence of [S, T,A, V][D, N][L, F]-[S, T,R][G]. The biochemical function of the vast majority of PRP family members is unknown. The three-dimensional structure of the first member of the PRP family was determined for the fluoroquinolone resistance protein (MfpA) from Mycobacterium tuberculosis. The structure revealed that the pentapeptide repeats encode the folding of a novel right-handed quadrilateral {beta}-helix. MfpA binds to DNA gyrase and inhibits its activity. The rod-shaped, dimeric protein exhibits remarkable size, shape and electrostatic similarity to DNA.

  17. Data correction techniques for the airborne large-aperture static image spectrometer based on image registration

    NASA Astrophysics Data System (ADS)

    Zhang, Geng; Shi, Dalian; Wang, Shuang; Yu, Tao; Hu, Bingliang

    2015-01-01

    We propose an approach to correct the data of the airborne large-aperture static image spectrometer (LASIS). LASIS is a kind of stationary interferometer which compromises flux output and device stability. It acquires a series of interferograms to reconstruct the hyperspectral image cube. Reconstruction precision of the airborne LASIS data suffers from the instability of the plane platform. Usually, changes of plane attitudes, such as yaws, pitches, and rolls, can be precisely measured by the inertial measurement unit. However, the along-track and across-track translation errors are difficult to measure precisely. To solve this problem, we propose a co-optimization approach to compute the translation errors between the interferograms using an image registration technique which helps to correct the interferograms with subpixel precision. To demonstrate the effectiveness of our approach, experiments are run on real airborne LASIS data and our results are compared with those of the state-of-the-art approaches.

  18. Honesty through repeated interactions.

    PubMed

    Rich, Patricia; Zollman, Kevin J S

    2016-04-21

    In the study of signaling, it is well known that the cost of deception is an essential element for stable honest signaling in nature. In this paper, we show how costs for deception can arise endogenously from repeated interactions between individuals. Utilizing the Sir Philip Sidney game as an illustrative case, we show that repeated interactions can sustain honesty with no observable signal costs, even when deception cannot be directly observed. We provide a number of potential experimental tests for this theory which distinguish it from the available alternatives. PMID:26869213

  19. Airborne Particulate Threat Assessment

    SciTech Connect

    Patrick Treado; Oksana Klueva; Jeffrey Beckstead

    2008-12-31

    Aerosol threat detection requires the ability to discern between threat agents and ambient background particulate matter (PM) encountered in the environment. To date, Raman imaging technology has been demonstrated as an effective strategy for the assessment of threat agents in the presence of specific, complex backgrounds. Expanding our understanding of the composition of ambient particulate matter background will improve the overall performance of Raman Chemical Imaging (RCI) detection strategies for the autonomous detection of airborne chemical and biological hazards. Improving RCI detection performance is strategic due to its potential to become a widely exploited detection approach by several U.S. government agencies. To improve the understanding of the ambient PM background with subsequent improvement in Raman threat detection capability, ChemImage undertook the Airborne Particulate Threat Assessment (APTA) Project in 2005-2008 through a collaborative effort with the National Energy Technology Laboratory (NETL), under cooperative agreement number DE-FC26-05NT42594. During Phase 1 of the program, a novel PM classification based on molecular composition was developed based on a comprehensive review of the scientific literature. In addition, testing protocols were developed for ambient PM characterization. A signature database was developed based on a variety of microanalytical techniques, including scanning electron microscopy, FT-IR microspectroscopy, optical microscopy, fluorescence and Raman chemical imaging techniques. An automated particle integrated collector and detector (APICD) prototype was developed for automated collection, deposition and detection of biothreat agents in background PM. During Phase 2 of the program, ChemImage continued to refine the understanding of ambient background composition. Additionally, ChemImage enhanced the APICD to provide improved autonomy, sensitivity and specificity. Deliverables included a Final Report detailing our

  20. Multiparametric airborne radar observations of the melting layer during the Wakasa Bay experiment

    NASA Technical Reports Server (NTRS)

    Tanelli, S.; Meagher, J.; Durden, S. L.; Im, E.

    2003-01-01

    The NASA/JPL airborne precipitation radar APR-2 (cross-track scanning, dual-frequency - 14 and 35 GHz, Doppler and dual polarization, see Sadowy et al. (2003) for detailed description of the instrument) was operated on the NASA P-3 aircraft during the Wakasa Bay experiment.

  1. Airborne GLM Simulator (FEGS)

    NASA Astrophysics Data System (ADS)

    Quick, M.; Blakeslee, R. J.; Christian, H. J., Jr.; Stewart, M. F.; Podgorny, S.; Corredor, D.

    2015-12-01

    Real time lightning observations have proven to be useful for advanced warning and now-casting of severe weather events. In anticipation of the launch of the Geostationary Lightning Mapper (GLM) onboard GOES-R that will provide continuous real time observations of total (both cloud and ground) lightning, the Fly's Eye GLM Simulator (FEGS) is in production. FEGS is an airborne instrument designed to provide cal/val measurements for GLM from high altitude aircraft. It consists of a 5 x 5 array of telescopes each with a narrow passband filter to isolate the 777.4 nm neutral oxygen emission triplet radiated by lightning. The telescopes will measure the optical radiance emitted by lightning that is transmitted through the cloud top with a temporal resolution of 10 μs. When integrated on the NASA ER-2 aircraft, the FEGS array with its 90° field-of-view will observe a cloud top area nearly equal to a single GLM pixel. This design will allow FEGS to determine the temporal and spatial variation of light that contributes to a GLM event detection. In addition to the primary telescope array, the instrument includes 5 supplementary optical channels that observe alternate spectral emission features and will enable the use of FEGS for interesting lightning physics applications. Here we present an up-to-date summary of the project and a description of its scientific applications.

  2. Airborne rescue system

    NASA Technical Reports Server (NTRS)

    Haslim, Leonard A. (Inventor)

    1991-01-01

    The airborne rescue system includes a boom with telescoping members for extending a line and collar to a rescue victim. The boom extends beyond the tip of the helicopter rotor so that the victim may avoid the rotor downwash. The rescue line is played out and reeled in by winch. The line is temporarily retained under the boom. When the boom is extended, the rescue line passes through clips. When the victim dons the collar and the tension in the line reaches a predetermined level, the clips open and release the line from the boom. Then the rescue line can form a straight line between the victim and the winch, and the victim can be lifted to the helicopter. A translator is utilized to push out or pull in the telescoping members. The translator comprises a tape and a rope. Inside the telescoping members the tape is curled around the rope and the tape has a tube-like configuration. The tape and rope are provided from supply spools.

  3. APEX: current status of the airborne dispersive pushbroom imaging spectrometer

    NASA Astrophysics Data System (ADS)

    Nieke, Jens; Itten, Klaus I.; Kaiser, Johannes W.; Schlapfer, Daniel R.; Brazile, Jason; Debruyn, Walter; Meuleman, Koen; Kempeneers, Pieter B.; Neukom, Andreas; Feusi, Hans; Adolph, Peter; Moser, Renzo; Schilliger, Thomas; van Quickelberghe, Marie; Alder, John; Mollet, Dominique; De Vos, Lieve; Kohler, Peter; Meng, Markus; Piesbergen, Jens; Strobl, Peter; Schaepman, Michael E.; Gavira, Jose; Ulbrich, Gerd J.; Meynart, Roland

    2004-10-01

    Recently, a joint Swiss/Belgian initiative started a project to build a new generation airborne imaging spectrometer, namely APEX (Airborne Prism Experiment) under the ESA funding scheme named PRODEX. APEX is a dispersive pushbroom imaging spectrometer operating in the spectral range between 380 - 2500 nm. The spectral resolution will be better then 10 nm in the SWIR and < 5 nm in the VNIR range of the solar reflected range of the spectrum. The total FOV will be +/- 14 deg, recording 1000 pixels across track with max. 300 spectral bands simultaneously. APEX is subdivided into an industrial team responsible for the optical instrument, the calibration homebase, and the detectors, and a science and operational team, responsible for the processing and archiving of the imaging spectrometer data, as well as for its operation. APEX is in its design phase and the instrument will be operationally available to the user community in the year 2006.

  4. An airborne system for detection of volcanic surface deformations

    NASA Technical Reports Server (NTRS)

    Lunine, J.

    1980-01-01

    A technique is proposed for measuring volcanic deformation on the order of centimeters per day to centimeters per year. An airborne multifrequency pulsed radar, tracking passive ground reflectors spaced at 1 kilometer intervals over a 50 square kilometer area is employed. Identification of targets is accomplished by Doppler and range resolution techniques, with final relative position measurements accomplished by phase comparison of multifrequency signals. Atmospheric path length errors are corrected by an airborne refractometer, meteorological instruments, or other refractive index measuring devices. Anticipated system accuracy is 1-2 cm, with measuring times on the order of minutes. Potential problems exist in the high intrinsic data assimilation rate required of the system to overcome ground backscatter noise.

  5. An update on the NAST-I airborne FTS

    NASA Astrophysics Data System (ADS)

    Larar, Allen M.; Smith, William L.; Zhou, Daniel K.; Liu, Xu; Noe, Anna; Oliver, Don; Flood, Michael; Rochette, Luc; Tian, Jialin

    2011-11-01

    The NPOESS / NASA Airborne Sounder Testbed - Interferometer (NAST-I) is a well-proven airborne remote sensing system, which has flown in 18 previous field campaigns aboard the high altitude NASA ER-2, Northrop Grumman / Scaled Composites Proteus, and NASA WB-57 aircraft since initially being flight qualified in 1998. While originally developed to provide experimental observations needed to finalize specifications and test proposed designs and data processing algorithms for the Cross-track Infrared Sounder (CrIS) to fly on the National Polar-orbiting Operational Environmental Satellite System (NPOESS) Preparatory Project (NPP) and the Joint Polar Satellite System, JPSS (formerly NPOESS, prior to recent program restructuring), its unprecedented data quality and system characteristics have contributed to a variety of atmospheric research and measurement validation objectives. This paper will provide a program overview and update, including a summary of measurement system capabilities, select scientific results, and recent refurbishment activities.

  6. Time-of-flight measurement techniques for airborne ultrasonic ranging.

    PubMed

    Jackson, Joseph C; Summan, Rahul; Dobie, Gordon I; Whiteley, Simon M; Pierce, S G; Hayward, Gordon

    2013-02-01

    Airborne ultrasonic ranging is used in a variety of different engineering applications for which other positional metrology techniques cannot be used, for example in closed-cell locations, when optical line of sight is limited, and when multipath effects preclude electromagnetic-based wireless systems. Although subject to fundamental physical limitations, e.g., because of the temperature dependence of acoustic velocity in air, these acoustic techniques often provide a cost-effective solution for applications in mobile robotics, structural inspection, and biomedical imaging. In this article, the different techniques and limitations of a range of airborne ultrasonic ranging approaches are reviewed, with an emphasis on the accuracy and repeatability of the measurements. Simple time-domain approaches are compared with their frequency-domain equivalents, and the use of hybrid models and biologically inspired approaches are discussed. PMID:23357908

  7. Triggering of repeated earthquakes

    NASA Astrophysics Data System (ADS)

    Sobolev, G. A.; Zakrzhevskaya, N. A.; Sobolev, D. G.

    2016-03-01

    Based on the analysis of the world's earthquakes with magnitudes M ≥ 6.5 for 1960-2013, it is shown that they cause global-scale coherent seismic oscillations which most distinctly manifest themselves in the period interval of 4-6 min during 1-3 days after the event. After these earthquakes, a repeated shock has an increased probability to occur in different seismically active regions located as far away as a few thousand km from the previous event, i.e., a remote interaction of seismic events takes place. The number of the repeated shocks N( t) decreases with time, which characterizes the memory of the lithosphere about the impact that has occurred. The time decay N( t) can be approximated by the linear, exponential, and powerlaw dependences. No distinct correlation between the spatial locations of the initial and repeated earthquakes is revealed. The probable triggering mechanisms of the remote interaction between the earthquakes are discussed. Surface seismic waves traveling several times around the Earth's, coherent oscillations, and global source are the most preferable candidates. This may lead to the accumulation and coalescence of ruptures in the highly stressed or weakened domains of a seismically active region, which increases the probability of a repeated earthquake.

  8. Repeated Causal Decision Making

    ERIC Educational Resources Information Center

    Hagmayer, York; Meder, Bjorn

    2013-01-01

    Many of our decisions refer to actions that have a causal impact on the external environment. Such actions may not only allow for the mere learning of expected values or utilities but also for acquiring knowledge about the causal structure of our world. We used a repeated decision-making paradigm to examine what kind of knowledge people acquire in…

  9. Bidirectional Manchester repeater

    NASA Technical Reports Server (NTRS)

    Ferguson, J.

    1980-01-01

    Bidirectional Manchester repeater is inserted at periodic intervals along single bidirectional twisted pair transmission line to detect, amplify, and transmit bidirectional Manchester 11 code signals. Requiring only 18 TTL 7400 series IC's, some line receivers and drivers, and handful of passive components, circuit is simple and relatively inexpensive to build.

  10. Aerosol Optical Depth Measurements by Airborne Sun Photometer in SOLVE II: Comparisons to SAGE III, POAM III and Airborne Spectrometer Measurements

    NASA Technical Reports Server (NTRS)

    Russell, P.; Livingston, J.; Schmid, B.; Eilers, J.; Kolyer, R.; Redemann, J.; Ramirez, S.; Yee, J-H.; Swartz, W.; Shetter, R.

    2004-01-01

    The 14-channel NASA Ames Airborne Tracking Sunphotometer (AATS-14) measured solar-beam transmission on the NASA DC-8 during the Second SAGE III Ozone Loss and Validation Experiment (SOLVE II). This paper presents AATS-14 results for multiwavelength aerosol optical depth (AOD), including its spatial structure and comparisons to results from two satellite sensors and another DC-8 instrument. These are the Stratospheric Aerosol and Gas Experiment III (SAGE III), the Polar Ozone and Aerosol Measurement III (POAM III) and the Direct beam Irradiance Airborne Spectrometer (DIAS).

  11. Respiration tracking in radiosurgery

    SciTech Connect

    Schweikard, Achim; Shiomi, Hiroya; Adler, John

    2004-10-01

    Respiratory motion is difficult to compensate for with conventional radiotherapy systems. An accurate tracking method for following the motion of the tumor is of considerable clinical relevance. We investigate methods to compensate for respiratory motion using robotic radiosurgery. In this system the therapeutic beam is moved by a robotic arm, and follows the moving target through a combination of infrared tracking and synchronized x-ray imaging. Infrared emitters are used to record the motion of the patient's skin surface. The position of internal gold fiducials is computed repeatedly during treatment, via x-ray image processing. We correlate the motion between external and internal markers. From this correlation model we infer the placement of the internal target during time intervals where no x-ray images are taken. Fifteen patients with lung tumors have recently been treated with a fully integrated system implementing this new method. The clinical trials confirm our hypothesis that internal motion and external motion are indeed correlated. In a preliminar study we have extended our work to tracking without implanted fiducials, based on algorithms for computing deformation motions and digitally reconstructed radiographs.

  12. Activity Tracking for Pilot Error Detection from Flight Data

    NASA Technical Reports Server (NTRS)

    Callantine, Todd J.; Ashford, Rose (Technical Monitor)

    2002-01-01

    This report presents an application of activity tracking for pilot error detection from flight data, and describes issues surrounding such an application. It first describes the Crew Activity Tracking System (CATS), in-flight data collected from the NASA Langley Boeing 757 Airborne Research Integrated Experiment System aircraft, and a model of B757 flight crew activities. It then presents an example of CATS detecting actual in-flight crew errors.

  13. A comparison of real and simulated airborne multisensor imagery

    NASA Astrophysics Data System (ADS)

    Bloechl, Kevin; De Angelis, Chris; Gartley, Michael; Kerekes, John; Nance, C. Eric

    2014-06-01

    This paper presents a methodology and results for the comparison of simulated imagery to real imagery acquired with multiple sensors hosted on an airborne platform. The dataset includes aerial multi- and hyperspectral imagery with spatial resolutions of one meter or less. The multispectral imagery includes data from an airborne sensor with three-band visible color and calibrated radiance imagery in the long-, mid-, and short-wave infrared. The airborne hyperspectral imagery includes 360 bands of calibrated radiance and reflectance data spanning 400 to 2450 nm in wavelength. Collected in September 2012, the imagery is of a park in Avon, NY, and includes a dirt track and areas of grass, gravel, forest, and agricultural fields. A number of artificial targets were deployed in the scene prior to collection for purposes of target detection, subpixel detection, spectral unmixing, and 3D object recognition. A synthetic reconstruction of the collection site was created in DIRSIG, an image generation and modeling tool developed by the Rochester Institute of Technology, based on ground-measured reflectance data, ground photography, and previous airborne imagery. Simulated airborne images were generated using the scene model, time of observation, estimates of the atmospheric conditions, and approximations of the sensor characteristics. The paper provides a comparison between the empirical and simulated images, including a comparison of achieved performance for classification, detection and unmixing applications. It was found that several differences exist due to the way the image is generated, including finite sampling and incomplete knowledge of the scene, atmospheric conditions and sensor characteristics. The lessons learned from this effort can be used in constructing future simulated scenes and further comparisons between real and simulated imagery.

  14. Airborne bio-optics survey of the Galapagos Islands margins

    NASA Astrophysics Data System (ADS)

    Hoge, Frank E.; Wayne Wright, C.; Swift, Robert N.; Yungel, James K.; Berry, Richard E.; Mitchell, Richard

    Aircraft and ship surveys of the Galapagos Islands were conducted to address the hypothesized influence of "island-leached" iron upon phytoplankton production. This paper describes the airborne survey of the Galapagos Islands that composed the second phase of a two-part study of the influence of iron on phytoplankton production in high-nutrient/low-chlorophyll (HNLC) regions. A single bio-optics airborne survey transect along 92°W from 1°N to 2°S was executed on 25 October 1993 in order to provide initial reconnaissance spatial and temporal sampling of the oceanic region west of the Galapagos Islands. A more extensive airborne bio-optics survey of the entire Galapagos Islands region was conducted on 3 November 1993. This expanded flight survey was made along all the ship cruise tracks of the R.V. Columbus Iselin originally planned for 15-27 November 1993. Analysis of the surface-layer airborne laser-induced and water-Raman normalized chlorophyll, phycoerythrin, and chromophoric dissolved organic matter (CDOM) fluorescence, SST, and AXBT (airborne expendable bathythermograph) data suggest that: (1) the regional distribution of phytoplankton and dissolved organic matter is dominated by the strong east-west thermal boundary located both east and west of the Galapagos Islands; (2) the source for the elevated phytoplankton patches west of the Galapagos Islands is from upwelling rather than aeolian sources or from the westward drift of iron and nutrients leached from the islands themselves or offshore shallow bottom sources; (3) the introduction of subsurface water to the surface may occur in episodic events rather than as a steady-state process; and (4) the chronic high chlorophyll west of the Galapagos Islands noted in processed Coastal Zone Color Scanner (CZCS) images may be due, at least in part, to the presence of elevated levels of chromophoric dissolved organic matter (CDOM) absorption.

  15. An automated data exploitation system for airborne sensors

    NASA Astrophysics Data System (ADS)

    Chen, Hai-Wen; McGurr, Mike

    2014-06-01

    Advanced wide area persistent surveillance (WAPS) sensor systems on manned or unmanned airborne vehicles are essential for wide-area urban security monitoring in order to protect our people and our warfighter from terrorist attacks. Currently, human (imagery) analysts process huge data collections from full motion video (FMV) for data exploitation and analysis (real-time and forensic), providing slow and inaccurate results. An Automated Data Exploitation System (ADES) is urgently needed. In this paper, we present a recently developed ADES for airborne vehicles under heavy urban background clutter conditions. This system includes four processes: (1) fast image registration, stabilization, and mosaicking; (2) advanced non-linear morphological moving target detection; (3) robust multiple target (vehicles, dismounts, and human) tracking (up to 100 target tracks); and (4) moving or static target/object recognition (super-resolution). Test results with real FMV data indicate that our ADES can reliably detect, track, and recognize multiple vehicles under heavy urban background clutters. Furthermore, our example shows that ADES as a baseline platform can provide capability for vehicle abnormal behavior detection to help imagery analysts quickly trace down potential threats and crimes.

  16. Airborne Laser Polar Nephelometer

    NASA Technical Reports Server (NTRS)

    Grams, Gerald W.

    1973-01-01

    A polar nephelometer has been developed at NCAR to measure the angular variation of the intensity of light scattered by air molecules and particles. The system has been designed for airborne measurements using outside air ducted through a 5-cm diameter airflow tube; the sample volume is that which is common to the intersection of a collimated source beam and the detector field of view within the airflow tube. The source is a linearly polarized helium-neon laser beam. The optical system defines a collimated field-of-view (0.5deg half-angle) through a series of diaphragms located behind a I72-mm focal length objective lens. A photomultiplier tube is located immediately behind an aperture in the focal plane of the objective lens. The laser beam is mechanically chopped (on-off) at a rate of 5 Hz; a two-channel pulse counter, synchronized to the laser output, measures the photomultiplier pulse rate with the light beam both on and off. The difference in these measured pulse rates is directly proportional to the intensity of the scattered light from the volume common to the intersection of the laser beam and the detector field-of-view. Measurements can be made at scattering angles from 15deg to 165deg with reference to the direction of propagation of the light beam. Intermediate angles are obtained by selecting the angular increments desired between these extreme angles (any multiple of 0.1deg can be selected for the angular increment; 5deg is used in normal operation). Pulses provided by digital circuits control a stepping motor which sequentially rotates the detector by pre-selected angular increments. The synchronous photon-counting system automatically begins measurement of the scattered-light intensity immediately after the rotation to a new angle has been completed. The instrument has been flown on the NASA Convair 990 airborne laboratory to obtain data on the complex index of refraction of atmospheric aerosols. A particle impaction device is operated simultaneously

  17. Accumulate repeat accumulate codes

    NASA Technical Reports Server (NTRS)

    Abbasfar, Aliazam; Divsalar, Dariush; Yao, Kung

    2004-01-01

    In this paper we propose an innovative channel coding scheme called 'Accumulate Repeat Accumulate codes' (ARA). This class of codes can be viewed as serial turbo-like codes, or as a subclass of Low Density Parity Check (LDPC) codes, thus belief propagation can be used for iterative decoding of ARA codes on a graph. The structure of encoder for this class can be viewed as precoded Repeat Accumulate (RA) code or as precoded Irregular Repeat Accumulate (IRA) code, where simply an accumulator is chosen as a precoder. Thus ARA codes have simple, and very fast encoder structure when they representing LDPC codes. Based on density evolution for LDPC codes through some examples for ARA codes, we show that for maximum variable node degree 5 a minimum bit SNR as low as 0.08 dB from channel capacity for rate 1/2 can be achieved as the block size goes to infinity. Thus based on fixed low maximum variable node degree, its threshold outperforms not only the RA and IRA codes but also the best known LDPC codes with the dame maximum node degree. Furthermore by puncturing the accumulators any desired high rate codes close to code rate 1 can be obtained with thresholds that stay close to the channel capacity thresholds uniformly. Iterative decoding simulation results are provided. The ARA codes also have projected graph or protograph representation that allows for high speed decoder implementation.

  18. Duct Leakage Repeatability Testing

    SciTech Connect

    Walker, Iain; Sherman, Max

    2014-01-01

    Duct leakage often needs to be measured to demonstrate compliance with requirements or to determine energy or Indoor Air Quality (IAQ) impacts. Testing is often done using standards such as ASTM E1554 (ASTM 2013) or California Title 24 (California Energy Commission 2013 & 2013b), but there are several choices of methods available within the accepted standards. Determining which method to use or not use requires an evaluation of those methods in the context of the particular needs. Three factors that are important considerations are the cost of the measurement, the accuracy of the measurement and the repeatability of the measurement. The purpose of this report is to evaluate the repeatability of the three most significant measurement techniques using data from the literature and recently obtained field data. We will also briefly discuss the first two factors. The main question to be answered by this study is to determine if differences in the repeatability of these tests methods is sufficient to indicate that any of these methods is so poor that it should be excluded from consideration as an allowed procedure in codes and standards.

  19. NASA Airborne-simulated Vertical Data in Google Earth

    NASA Astrophysics Data System (ADS)

    Chen, A.; Leptoukh, G.; Kempler, S.; Liu, Z.

    2008-12-01

    Google Earth has been widely used as a tool to visualize scientific data that have geospatial elements. The data can be two dimensional and three dimensional, or even four-dimensional. NASA A-Train constellation satellites such as CloudSat, CALIPSO (Cloud-Aerosol Lidar and Infrared Pathfinder Satellite Observation), and Aqua have been producing lots of vertical data about the atmosphere. Those data are being used for such scientific research as global climate change, weather forecast, etc. NASA also uses airplanes to load some instruments to simulate satellite flying for establishing the sensitivity, calibration, and initial validation of the instruments that will be loaded at satellites. The airborne simulated flying produces simulated vertical data of the atmosphere. Visualization of these kinds of vertical data in Google Earth is helpful for scientific research. Here, a new method is proposed to visualize the simulated vertical data in Google Earth to expose cloud, aerosol, and other atmospheric profiles in the form of curtain along the flying track of the airplane. An interface description language-based render is designed and implemented to process and display the simulated vertical data in the format of image. The image is further processed and cut into transparent small image slices according to the track of the airplane. A COLLADA (COLLAborative Design Activity) 3D model, which is supported by Google Earth, is devised to make the image slices vertically displayed in Google Earth. Using the COLLADA models and airplane flying track coordinates, an airplane track model is implemented in the format of KML (Keyhole Markup Language). The track curtain makes simulated vertical data viewable, transparently or opaquely, in Google Earth. Thus, airborne simulated vertical geospatial data are available to scientists and the general public in a popular venue.

  20. An airborne isothermal haze chamber

    NASA Technical Reports Server (NTRS)

    Hindman, E. E.

    1981-01-01

    Thermal gradient diffusion cloud chambers (TGDCC) are used to determine the concentrations of cloud condensation nuclei (CCN) with critical supersaturations greater than or equal to about 0.2%. The CCN concentrations measured with the airborne IHC were lower than theoretically predicted by factors ranging between 7.9 and 9.0. The CCN concentrations measured with the airborne IHC were lower than the concentrations measured with the larger laboratory IHC's by factors ranging between 3.9 and 7.5. The bounds of the supersaturation ranges of the airborne IHC and the CSU-Mee TGDCC do not overlap. Nevertheless, the slopes of the interpolated data between the bounds agree favorably with the theoretical slopes.

  1. Airborne laser topographic mapping results

    NASA Technical Reports Server (NTRS)

    Krabill, W. B.; Collins, J. G.; Link, L. E.; Swift, R. N.; Butler, M. L.

    1984-01-01

    The results of terrain mapping experiments utilizing the National Aeronautics and Space Administration (NASA) Airborne Oceanographic Lidar (AOL) over forested areas are presented. The flight tests were conducted as part of a joint NASA/U.S. Army Corps of Engineers (CE) investigation aimed at evaluating the potential of an airborne laser ranging system to provide cross-sectional topographic data on flood plains that are difficult and expensive to survey using conventional techniques. The data described in this paper were obtained in the Wolf River Basin located near Memphis, TN. Results from surveys conducted under winter 'leaves off' and summer 'leaves on' conditions, aspects of day and night operation, and data obtained from decidous and coniferous tree types are compared. Data processing techniques are reviewed. Conclusions relative to accuracy and present limitations of the AOL, and airborne lidar systems in general, to terrain mapping over forested areas are discussed.

  2. WESTERN AIRBORNE CONTAMINANTS ASSESSMENT PROJECT RESEARCH PLAN

    EPA Science Inventory

    The goal of the Western Airborne Contaminants Assessment Project (WACAP) is to assess the deposition of airborne contaminants in Western National Parks, providing regional and local information on exposure, accumulation, impacts, and probable sources. This project is being desig...

  3. Results from 1984 airborne Doppler lidar wind measurements

    NASA Technical Reports Server (NTRS)

    Rothermel, Jeffry

    1986-01-01

    Observations made with the revised Airborne Doppler Lidar System (ADLS) during research flights in the summer of 1984 are described. The functioning of the ADLS system is described. The research flights measured the flow around Mt. Shasta about 3 km above the surrounding terrain as well as the flow in the area of the Carquenez Strait in the Sacramento River Valley. The flight tracks are described and the resulting scan radial velocities are shown and discussed. The results demonstrate the success of the modifications made in order to correct major error sources present in the 1981 flights of the ADLS system.

  4. The NASA/JPL Airborne Synthetic Aperture Radar System

    NASA Technical Reports Server (NTRS)

    Lou, Yunling; Kim,Yunjin; vanZyl, Jakob

    1996-01-01

    In this paper we will briefly describe the instrument characteristics, the evolution of various radar modes, the instrument performance and improvement in the knowledge of the positioning and attitude information of the NASA/JPL airborne synthetic aperture radar (SAR). This system operates in the fully polarimetric mode in the P, L, and C band simultaneously or in the interferometric mode in both the L and C band simultaneously. We also summarize the progress of the data processing effort, especially in the interferometry processing and we address the issue of processing and calibrating the cross-track interferometry data.

  5. Electronics design of the airborne stabilized platform attitude acquisition module

    NASA Astrophysics Data System (ADS)

    Xu, Jiang; Wei, Guiling; Cheng, Yong; Li, Baolin; Bu, Hongyi; Wang, Hao; Zhang, Zhanwei; Li, Xingni

    2014-02-01

    We present an attitude acquisition module electronics design for the airborne stabilized platform. The design scheme, which is based on Integrated MEMS sensor ADIS16405, develops the attitude information processing algorithms and the hardware circuit. The hardware circuits with a small volume of only 44.9 x 43.6 x 24.6 mm3, has the characteristics of lightweight, modularization and digitalization. The interface design of the PC software uses the combination plane chart with track line to receive the attitude information and display. Attitude calculation uses the Kalman filtering algorithm to improve the measurement accuracy of the module in the dynamic environment.

  6. Chemical detection using the airborne thermal infrared imaging spectrometer (TIRIS)

    SciTech Connect

    Gat, N.; Subramanian, S.; Sheffield, M.; Erives, H.; Barhen, J.

    1997-04-01

    A methodology is described for an airborne, downlooking, longwave infrared imaging spectrometer based technique for the detection and tracking of plumes of toxic gases. Plumes can be observed in emission or absorption, depending on the thermal contrast between the vapor and the background terrain. While the sensor is currently undergoing laboratory calibration and characterization, a radiative exchange phenomenology model has been developed to predict sensor response and to facilitate the sensor design. An inverse problem model has also been developed to obtain plume parameters based on sensor measurements. These models, the sensors, and ongoing activities are described.

  7. Doppler tracking

    NASA Astrophysics Data System (ADS)

    Thomas, Christopher Jacob

    This study addresses the development of a methodology using the Doppler Effect for high-resolution, short-range tracking of small projectiles and vehicles. Minimal impact on the design of the moving object is achieved by incorporating only a transmitter in it and using ground stations for all other components. This is particularly useful for tracking objects such as sports balls that have configurations and materials that are not conducive to housing onboard instrumentation. The methodology developed here uses four or more receivers to monitor a constant frequency signal emitted by the object. Efficient and accurate schemes for filtering the raw signals, determining the instantaneous frequencies, time synching the frequencies from each receiver, smoothing the synced frequencies, determining the relative velocity and radius of the object and solving the nonlinear system of equations for object position in three dimensions as a function of time are developed and described here.

  8. NASA Airborne Lidar 1982-1984 Flights

    Atmospheric Science Data Center

    2016-05-26

    NASA Airborne Lidar 1982-1984 Flights Data from the 1982 NASA Langley Airborne Lidar flights following the eruption of El Chichon ... continuing to January 1984. Transcribed from the following NASA Tech Reports: McCormick, M. P., and M. T. Osborn, Airborne lidar ...

  9. Use of airborne thermal imagery to detect and monitor inshore oil spill residues during darkness hours

    SciTech Connect

    Grierson, I.T.

    1998-11-01

    Trials were conducted using an airborne video system operating in the visible, near-infrared, and thermal wavelengths to detect two known oil spill releases during darkness at a distance of 10 nautical miles from the shore in St. Vincent`s Gulf, South Australia. The oil spills consisted of two 20-liter samples released at 2-h intervals, one sample consisted of paraffinic neutral material and the other of automotive diesel oil. A tracking buoy was sent overboard in conjunction with the release of sample 1, and its movement monitored by satellite relay. Both oil residues were overflown by a light aircraft equipped with thermal, visible, and infrared imagers at a period of approximately 1 h after the release of the second oil residue. Trajectories of the oil residue releases were also modeled and the results compared to those obtained by the airborne video and the tracking buoy. Airborne imagery in the thermal wavelengths successfully located and mapped both oil residue samples during nighttime conditions. Results from the trial suggest that the most advantageous technique would be the combined use of the tracking beacon to obtain an approximate location of the oil spill and the airborne imagery to ascertain its extent and characteristics.

  10. LOREP 1993 summary report: Airborne measurements of meteorological variables, atmospheric particles and sulfur hexafluoride. Technical memo

    SciTech Connect

    Wilkison, S.W.; Wellman, D.L.

    1996-03-01

    Meteorological variables and sulfur hexafluoride (SF6) were measured using the NOAA King Air research aircraft during February and March, 1993, over the Sierra Nevada Range of northern California as part of the Lake Oroville Runoff Enhancement Prototype Program (LOREP 1993). Race track pattern flights were made from approximately Sierraville, CA, to Gasner, CA. Airborne sampling was used to locate a plume containing sulfur hexafluoride as a tracer and propane as a seeding agent. The aircraft also carried an optical imaging probe. This report introduces the program in general, discusses the objectives of LOREP 1993, the instrumentation used and the data obtained by the NOAA airborne operation.

  11. Wave-measurement capabilities of the surface contour radar and the airborne oceanographic lidar

    NASA Technical Reports Server (NTRS)

    Walsh, Edward J.; Hancock, David W., III; Hines, Donald E.; Swift, Robert N.; Scott, John F.

    1987-01-01

    The 36-gigahertz surface contour radar and the airborne oceanographic lidar were used in the SIR-B underflight mission off the coast of Chile in October 1984. The two systems and some of their wave-measurement capabilities are described. The surface contour radar can determine the directional wave spectrum and eliminate the 180-degree ambiguity in wave propagation direction that is inherent in some other techniques such as stereophotography and the radar ocean wave spectrometer. The Airborne Oceanographic Lidar can acquire profile data on the waves and produce a spectrum that is close to the nondirectional ocean-wave spectrum for ground tracks parallel to the wave propagation direction.

  12. Michigan experimental multispectral mapping system: A description of the M7 airborne sensor and its performance

    NASA Technical Reports Server (NTRS)

    Hasell, P. G., Jr.

    1974-01-01

    The development and characteristics of a multispectral band scanner for an airborne mapping system are discussed. The sensor operates in the ultraviolet, visual, and infrared frequencies. Any twelve of the bands may be selected for simultaneous, optically registered recording on a 14-track analog tape recorder. Multispectral imagery recorded on magnetic tape in the aircraft can be laboratory reproduced on film strips for visual analysis or optionally machine processed in analog and/or digital computers before display. The airborne system performance is analyzed.

  13. A phased array tracking antenna for vehicles

    NASA Technical Reports Server (NTRS)

    Ohmori, Shingo; Mano, Kazukiko; Tanaka, Kenji; Matsunaga, Makoto; Tsuchiya, Makio

    1990-01-01

    An antenna system including antenna elements and a satellite tracking method is considered a key technology in implementing land mobile satellite communications. In the early stage of land mobile satellite communications, a mechanical tracking antenna system is considered the best candidate for vehicles, however, a phased array antenna will replace it in the near future, because it has many attractive advantages such as a low and compact profile, high speed tracking, and potential low cost. Communications Research Laboratory is now developing a new phased array antenna system for land vehicles based on research experiences of the airborne phased array antenna, which was developed and evaluated in satellite communication experiments using the ETS-V satellite. The basic characteristics of the phased array antenna for land vehicles are described.

  14. Airborne Imagery Collections Barrow 2013

    DOE Data Explorer

    Cherry, Jessica; Crowder, Kerri

    2015-07-20

    The data here are orthomosaics, digital surface models (DSMs), and individual frames captured during low altitude airborne flights in 2013 at the Barrow Environmental Observatory. The orthomosaics, thermal IR mosaics, and DSMs were generated from the individual frames using Structure from Motion techniques.

  15. Airborne fungi--a resurvey

    SciTech Connect

    Meyer, G.H.; Prince, H.E.; Raymer, W.J.

    1983-07-01

    A 15-month survey of airborne fungi at 14 geographical stations was conducted to determine the incidence of different fungal genera. Five of these stations were surveyed 25 years earlier. A comparison between previous studies and present surveys revealed similar organisms at each station with slight shifts in frequency of dominant genera.

  16. Tropospheric and Airborne Emission Spectrometers

    NASA Technical Reports Server (NTRS)

    Glavich, Thomas; Beer, Reinhard

    1996-01-01

    X This paper describes the development of two related instruments, the Tropospheric Emission Spectrometer (TES) and the Airborne Emission Spectrometer (AES). Both instruments are infrared imaging Fourier Transform Spectrometers, used for measuring the state of the lower atmosphere, and in particular the measurement of ozone and ozone sources and sinks.

  17. AARD - Autonomous Airborne Refueling Demonstration

    NASA Technical Reports Server (NTRS)

    Ewers, Dick

    2007-01-01

    This viewgraph document reviews the Autonomous Airborne Refueling Demonstration program, and NASA Dryden's work in the program. The primary goal of the program is to make one fully automatic probe-to-drogue engagement using the AARD system. There are pictures of the aircraft approaching to the docking.

  18. Airborne asbestos in public buildings

    SciTech Connect

    Chesson, J.; Hatfield, J.; Schultz, B.; Dutrow, E.; Blake, J. )

    1990-02-01

    The U.S. Environmental Protection Agency sampled air in 49 government-owned buildings (six buildings with no asbestos-containing material, six buildings with asbestos-containing material in generally good condition, and 37 buildings with damaged asbestos-containing material). This is the most comprehensive study to date of airborne asbestos levels in U.S. public buildings during normal building activities. The air outside each building was also sampled. Air samples were analyzed by transmission electron microscopy using a direct transfer preparation technique. The results show an increasing trend in average airborne asbestos levels; outdoor levels are lowest and levels in buildings with damaged asbestos-containing material are highest. However, the measured levels and the differences between indoors and outdoors and between building categories are small in absolute magnitude. Comparable studies from Canada and the UK, although differing in their estimated concentrations, also conclude that while airborne asbestos levels may be elevated in buildings that contain asbestos, levels are generally low. This conclusion does not eliminate the possibility of higher airborne asbestos levels during maintenance or renovation that disturbs the asbestos-containing material.

  19. Duct Leakage Repeatability Testing

    SciTech Connect

    Walker, Iain; Sherman, Max

    2014-08-01

    The purpose of this report is to evaluate the repeatability of the three most significant measurement techniques for duct leakage using data from the literature and recently obtained field data. We will also briefly discuss the first two factors. The main question to be answered by this study is to determine if differences in the repeatability of these tests methods is sufficient to indicate that any of these methods is so poor that it should be excluded from consideration as an allowed procedure in codes and standards. The three duct leak measurement methods assessed in this report are the two duct pressurization methods that are commonly used by many practitioners and the DeltaQ technique. These are methods B, C and A, respectively of the ASTM E1554 standard. Although it would be useful to evaluate other duct leak test methods, this study focused on those test methods that are commonly used and are required in various test standards, such as BPI (2010), RESNET (2014), ASHRAE 62.2 (2013), California Title 24 (CEC 2012), DOE Weatherization and many other energy efficiency programs.

  20. Repeated measures with zeros.

    PubMed

    Berk, K N; Lachenbruch, P A

    2002-08-01

    Consider repeated measures data with many zeros. For the case with one grouping factor and one repeated measure, we examine several models, assuming that the nonzero data are roughly lognormal. One of the simplest approaches is to model the zeros as left-censored observations from the lognormal distribution. A random effect is assumed for subjects. The censored model makes a strong assumption about the relationship between the zeros and the nonzero values. To check on this, you can instead assume that some of the zeros are 'true' zeros and model them as Bernoulli. Then the other values are modeled with a censored lognormal. A logistic model is used for the Bernoulli p, the probability of a true nonzero. The fit of the pure left-censored lognormal can be assessed by testing the hypothesis that p is 1, as described by Moulton and Halsey. The model can also be simplified by omitting the censoring, leaving a logistic model for the zeros and a lognormal model for the nonzero values. This is approximately equivalent to modeling the zero and nonzero values separately, a two-part model. In contrast to the censored model, this model assumes only a slight relationship (a covariance component) between the occurrence of zeros and the size of the nonzero values. The models are compared in terms of an example with data from children's private speech. PMID:12197298

  1. Applications of airborne ultrasound in human-computer interaction.

    PubMed

    Dahl, Tobias; Ealo, Joao L; Bang, Hans J; Holm, Sverre; Khuri-Yakub, Pierre

    2014-09-01

    Airborne ultrasound is a rapidly developing subfield within human-computer interaction (HCI). Touchless ultrasonic interfaces and pen tracking systems are part of recent trends in HCI and are gaining industry momentum. This paper aims to provide the background and overview necessary to understand the capabilities of ultrasound and its potential future in human-computer interaction. The latest developments on the ultrasound transducer side are presented, focusing on capacitive micro-machined ultrasonic transducers, or CMUTs. Their introduction is an important step toward providing real, low-cost multi-sensor array and beam-forming options. We also provide a unified mathematical framework for understanding and analyzing algorithms used for ultrasound detection and tracking for some of the most relevant applications. PMID:24974162

  2. Repeat Customer Success in Extension

    ERIC Educational Resources Information Center

    Bess, Melissa M.; Traub, Sarah M.

    2013-01-01

    Four multi-session research-based programs were offered by two Extension specialist in one rural Missouri county. Eleven participants who came to multiple Extension programs could be called "repeat customers." Based on the total number of participants for all four programs, 25% could be deemed as repeat customers. Repeat customers had…

  3. Airborne radar surveys of snow depth over Antarctic sea ice during Operation IceBridge

    NASA Astrophysics Data System (ADS)

    Panzer, B.; Gomez-Garcia, D.; Leuschen, C.; Paden, J. D.; Gogineni, P. S.

    2012-12-01

    Over the last decade, multiple satellite-based laser and radar altimeters, optimized for polar observations, have been launched with one of the major objectives being the determination of global sea ice thickness and distribution [5, 6]. Estimation of sea-ice thickness from these altimeters relies on freeboard measurements and the presence of snow cover on sea ice affects this estimate. Current means of estimating the snow depth rely on daily precipitation products and/or data from passive microwave sensors [2, 7]. Even a small uncertainty in the snow depth leads to a large uncertainty in the sea-ice thickness estimate. To improve the accuracy of the sea-ice thickness estimates and provide validation for measurements from satellite-based sensors, the Center for Remote Sensing of Ice Sheets deploys the Snow Radar as a part of NASA Operation IceBridge. The Snow Radar is an ultra-wideband, frequency-modulated, continuous-wave radar capable of resolving snow depth on sea ice from 5 cm to more than 2 meters from long-range, airborne platforms [4]. This paper will discuss the algorithm used to directly extract snow depth estimates exclusively using the Snow Radar data set by tracking both the air-snow and snow-ice interfaces. Prior work in this regard used data from a laser altimeter for tracking the air-snow interface or worked under the assumption that the return from the snow-ice interface was greater than that from the air-snow interface due to a larger dielectric contrast, which is not true for thick or higher loss snow cover [1, 3]. This paper will also present snow depth estimates from Snow Radar data during the NASA Operation IceBridge 2010-2011 Antarctic campaigns. In 2010, three sea ice flights were flown, two in the Weddell Sea and one in the Amundsen and Bellingshausen Seas. All three flight lines were repeated in 2011, allowing an annual comparison of snow depth. In 2011, a repeat pass of an earlier flight in the Weddell Sea was flown, allowing for a

  4. Airborne Optical Communications Demonstrator Design And Preflight Test Results

    NASA Technical Reports Server (NTRS)

    Biswas, Abhijit; Page, N.; Neal, J.; Zhu, D.; Wright, M.; Ovtiz, G.; Farr, W. H.; Hernnzati, H.

    2005-01-01

    A second generation optical communications demonstrator (OCD-2) intended for airborne applications like air-to-ground and air-to-air optical links is under development at JPL. This development provides the capability for unidirectional high data rate (2.5-Gbps) transmission at 1550-nm, with the ability to receive an 810-nm beacon to aid acquisition pointing and tracking. The transmitted beam width is nominally 200-(micro)rad. A 3x3 degree coarse field-of-view (FOV) acquisition sensor with a much smaller 3-mrad FOV tracking sensor is incorporated. The OCD-2 optical head will be integrated to a high performance gimbal turret assembly capable of providing pointing stability of 5- microradians from an airborne platform. Other parts of OCD-2 include a cable harness, connecting the optical head in the gimbal turret assembly to a rugged electronics box. The electronics box will house: command and control processors, laser transmitter, data-generation-electronics, power conversion/distribution hardware and state-of-health monitors. The entire assembly will be integrated and laboratory tested prior to a planned flight demonstrations.

  5. Satellite and airborne IR sensor validation by an airborne interferometer

    SciTech Connect

    Gumley, L.E.; Delst, P.F. van; Moeller, C.C.

    1996-11-01

    The validation of in-orbit longwave IR radiances from the GOES-8 Sounder and inflight longwave IR radiances from the MODIS Airborne Simulator (MAS) is described. The reference used is the airborne University of Wisconsin High Resolution Interferometer Sounder (HIS). The calibration of each sensor is described. Data collected during the Ocean Temperature Interferometric Survey (OTIS) experiment in January 1995 is used in the comparison between sensors. Detailed forward calculations of at-sensor radiance are used to account for the difference in GOES-8 and HIS altitude and viewing geometry. MAS radiances and spectrally averaged HIS radiances are compared directly. Differences between GOES-8 and HIS brightness temperatures, and GOES-8 and MAS brightness temperatures, are found to be with 1.0 K for the majority of longwave channels examined. The same validation approach will be used for future sensors such as the Moderate Resolution Imaging Spectroradiometer (MODIS) and the Atmospheric Infrared Sounder (AIRS). 11 refs., 2 figs., 4 tabs.

  6. RepeatsDB: a database of tandem repeat protein structures

    PubMed Central

    Di Domenico, Tomás; Potenza, Emilio; Walsh, Ian; Gonzalo Parra, R.; Giollo, Manuel; Minervini, Giovanni; Piovesan, Damiano; Ihsan, Awais; Ferrari, Carlo; Kajava, Andrey V.; Tosatto, Silvio C.E.

    2014-01-01

    RepeatsDB (http://repeatsdb.bio.unipd.it/) is a database of annotated tandem repeat protein structures. Tandem repeats pose a difficult problem for the analysis of protein structures, as the underlying sequence can be highly degenerate. Several repeat types haven been studied over the years, but their annotation was done in a case-by-case basis, thus making large-scale analysis difficult. We developed RepeatsDB to fill this gap. Using state-of-the-art repeat detection methods and manual curation, we systematically annotated the Protein Data Bank, predicting 10 745 repeat structures. In all, 2797 structures were classified according to a recently proposed classification schema, which was expanded to accommodate new findings. In addition, detailed annotations were performed in a subset of 321 proteins. These annotations feature information on start and end positions for the repeat regions and units. RepeatsDB is an ongoing effort to systematically classify and annotate structural protein repeats in a consistent way. It provides users with the possibility to access and download high-quality datasets either interactively or programmatically through web services. PMID:24311564

  7. Simulation of Terminal-Area Flight Management System Arrivals with Airborne Spacing

    NASA Technical Reports Server (NTRS)

    Callantine, Todd J.; Lee, Paul U.; Mercer, Joey S.; Palmer, Everett A.; Prevot, Thomas

    2007-01-01

    A simulation evaluated the feasibility and potential benefits of using decision support tools to support time-based airborne spacing and merging for aircraft arriving in the terminal area on charted Flight Management System (FMS) routes. Sixteen trials were conducted in each treatment combination of a 2X2 repeated-measures design. In trials 'with ground tools' air traffic controller participants managed traffic using sequencing and spacing tools. In trials 'with air tools' approximately seventy-five percent of aircraft assigned to the primary landing runway were equipped for airborne spacing, including flight simulators flown by commercial pilots. The results indicate that airborne spacing improves spacing accuracy and is feasible for FMS operations and mixed spacing equipage. Controllers and pilots can manage spacing clearances that contain two call signs without difficulty. For best effect, both decision support tools and spacing guidance should exhibit consistently predictable performance, and merging traffic flows should be well coordinated.

  8. Large aperture scanning airborne lidar

    NASA Technical Reports Server (NTRS)

    Smith, J.; Bindschadler, R.; Boers, R.; Bufton, J. L.; Clem, D.; Garvin, J.; Melfi, S. H.

    1988-01-01

    A large aperture scanning airborne lidar facility is being developed to provide important new capabilities for airborne lidar sensor systems. The proposed scanning mechanism allows for a large aperture telescope (25 in. diameter) in front of an elliptical flat (25 x 36 in.) turning mirror positioned at a 45 degree angle with respect to the telescope optical axis. The lidar scanning capability will provide opportunities for acquiring new data sets for atmospheric, earth resources, and oceans communities. This completed facility will also make available the opportunity to acquire simulated EOS lidar data on a near global basis. The design and construction of this unique scanning mechanism presents exciting technological challenges of maintaining the turning mirror optical flatness during scanning while exposed to extreme temperatures, ambient pressures, aircraft vibrations, etc.

  9. Magnetic airborne survey - geophysical flight

    NASA Astrophysics Data System (ADS)

    de Barros Camara, Erick; Nei Pereira Guimarães, Suze

    2016-06-01

    This paper provides a technical review process in the area of airborne acquisition of geophysical data, with emphasis for magnetometry. In summary, it addresses the calibration processes of geophysical equipment as well as the aircraft to minimize possible errors in measurements. The corrections used in data processing and filtering are demonstrated with the same results as well as the evolution of these techniques in Brazil and worldwide.

  10. Airborne microorganisms from waste containers.

    PubMed

    Jedlicka, Sabrina S; Stravitz, David M; Lyman, Charles E

    2012-01-01

    In physician's offices and biomedical labs, biological waste is handled every day. This waste is disposed of in waste containers designed for holding red autoclave bags. The containers used in these environments are closed hands-free containers, often with a step pedal. While these containers protect the user from surface-borne microorganisms, the containers may allow airborne microorganisms to escape via the open/close mechanism because of the air current produced upon open/close cycles. In this study, the air current was shown to be sufficient to allow airborne escape of microorganisms held in the container, including Aspergillus niger. However, bacterial cultures, such as Escherichia coli and Lactococcus lactis did not escape. This may be due to the choice of bacterial cultures and the absence of solid waste, such as dust or other particulate matter in the waste containers, that such strains of bacteria could travel on during aerosolization. We compared these results to those obtained using a re-designed receptacle, which mimimizes air currents, and detected no escaping microorganisms. This study highlights one potential source of airborne contamination in labs, hospitals, and other environments that dispose of biological waste. PMID:23047084

  11. Airborne lidar global positioning investigations

    NASA Technical Reports Server (NTRS)

    Krabill, W. B.

    1988-01-01

    The Global Positioning System (GPS) network of satellites shows high promise of revolutionizing methods for conducting surveying, navigation, and positioning. This is especially true in the case of airborne or satellite positioning. A single GPS receiver (suitably adapted for aircraft deployment) can yield positioning accuracies (world-wide) in the order of 30 to 50 m vertically, as well as horizontally. This accuracy is dramatically improved when a second GPS receiver is positioned at a known horizontal and vertical reference. Absolute horizontal and vertical positioning of 1 to 2 m are easily achieved over areas of separation of tens of km. If four common satellites remain in lock in both receivers, then differential phase pseudo-ranges on the GPS L-band carrier can be utilized to achieve accuracies of + or - 10 cm and perhaps as good as + or - 2 cm. The initial proof of concept investigation for airborne positioning using the phase difference between the airborne and stationary GPS receivers was conducted and is examined.

  12. NASA Student Airborne Research Program

    NASA Astrophysics Data System (ADS)

    Schaller, E. L.; Shetter, R. E.

    2012-12-01

    The NASA Student Airborne Research Program (SARP) is a unique summer internship program for advanced undergraduates and early graduate students majoring in the STEM disciplines. SARP participants acquire hands-on research experience in all aspects of an airborne research campaign, including flying onboard an major NASA resource used for studying Earth system processes. In summer 2012, thirty-two participants worked in four interdisciplinary teams to study surface, atmospheric, and oceanographic processes. Participants assisted in the operation of instruments onboard the NASA P-3B aircraft where they sampled and measured atmospheric gases and imaged land and water surfaces in multiple spectral bands. Along with airborne data collection, students participated in taking measurements at field sites. Mission faculty and research mentors helped to guide participants through instrument operation, sample analysis, and data reduction. Over the eight-week program, each student developed an individual research project from the data collected and delivered a conference-style final presentation on his/her results. We will discuss the results and effectiveness of the program from the first four summers and discuss plans for the future.

  13. Airborne particulate matter in spacecraft

    NASA Technical Reports Server (NTRS)

    1988-01-01

    Acceptability limits and sampling and monitoring strategies for airborne particles in spacecraft were considered. Based on instances of eye and respiratory tract irritation reported by Shuttle flight crews, the following acceptability limits for airborne particles were recommended: for flights of 1 week or less duration (1 mg/cu m for particles less than 10 microns in aerodynamic diameter (AD) plus 1 mg/cu m for particles 10 to 100 microns in AD); and for flights greater than 1 week and up to 6 months in duration (0.2 mg/cu m for particles less than 10 microns in AD plus 0.2 mg/cu m for particles 10 to 100 microns in AD. These numerical limits were recommended to aid in spacecraft atmosphere design which should aim at particulate levels that are a low as reasonably achievable. Sampling of spacecraft atmospheres for particles should include size-fractionated samples of 0 to 10, 10 to 100, and greater than 100 micron particles for mass concentration measurement and elementary chemical analysis by nondestructive analysis techniques. Morphological and chemical analyses of single particles should also be made to aid in identifying airborne particulate sources. Air cleaning systems based on inertial collection principles and fine particle collection devices based on electrostatic precipitation and filtration should be considered for incorporation into spacecraft air circulation systems. It was also recommended that research be carried out in space in the areas of health effects and particle characterization.

  14. Track Construction Manual.

    ERIC Educational Resources Information Center

    Banke, Ron; Di Gennaro, Guy; Ediger, Rick; Garner, Lanny; Hersom, Steve; Miller, Jack; Nemeth, Ron; Petrucelli, Jim; Sierks, Donna; Smith, Don; Swank, Kevin; West, Kevin

    This book establishes guidelines for the construction and maintenance of tracks by providing information for building new tracks or upgrading existing tracks. Subjects covered include running track planning and construction, physical layout, available surfaces, and maintenance. General track requirements and construction specifications are…

  15. On the Right Track.

    ERIC Educational Resources Information Center

    Bieber, Ed

    1983-01-01

    Suggests thinking of "tracks" as clues and using them as the focus of outdoor activities in the urban environment. Provides 24 examples of possible track activities, including: seeds on the ground (track of a nearby tree), litter (track of a litterbug), and peeling paint (track of weathering forces). (JN)

  16. Overview of the Airborne Tropical TRopopause EX

    NASA Technical Reports Server (NTRS)

    Singh, Hanwant B.; Jensen, Eric J.; Pfister, Leonhard

    2014-01-01

    The NASA Airborne Tropical TRopopause EXperiment (ATTREX) is a series of airborne campaigns focused on understanding physical processes in the Tropical Tropopause Layer (TTL) and their role in atmospheric chemistry and climate. ATTREX is using the high-altitude, long-duration NASA Global Hawk Unmanned Air System to make in situ and remote-sensing measurements spanning the Pacific. A particular ATIREX emphasis is to better understand the dehydration of air as it passes through the cold tropical tropopause region. The ATTREX payload contains 12 in situ and remote sensing instruments that measure water vapor, clouds, multiple gaseous tracers (CO, CO2, CH4, NMHC, SF6, CFCs, N2O), reactive chemical compounds (O3, BrO, NO2), meteorological parameters, and radiative fluxes. ATTREX flight series have been conducted in the fall of 2011 from Armstrong Flight Research Center (AFRC) in California, in the winter of 2013 from AFRC, and in the winter/spring of 2014 from Guam. The first two f light series provided extensive sampling of the central and eastern Pacific, whereas the last flight series permitted sampling in the western Pacific. The sampling strategy has primarily involved repeated ascents and descents through the depth of the TTL (about 13-19 km). Over 100 TTL profiles were obtained on each flight series. The ATTREX dataset includes TTL water vapor measurements with unprecedented accuracy, ice crystal size distributions and habits. The cloud and water measurements provide unique information about TTL cloud formation, the persistence of supersaturation with respect to ice, and dehydration. The plethora of tracers measured on the Global Hawk flights are providing unique information about TTL transport pathways and time scales. The meteorological measurements are revealing dynamical phenomena controlling the TTL thermal structure, and the radiation measurements are providing information about heating rates associated with TTL clouds and water vapor. This presentation

  17. High Resolution Airborne Shallow Water Mapping

    NASA Astrophysics Data System (ADS)

    Steinbacher, F.; Pfennigbauer, M.; Aufleger, M.; Ullrich, A.

    2012-07-01

    In order to meet the requirements of the European Water Framework Directive (EU-WFD), authorities face the problem of repeatedly performing area-wide surveying of all kinds of inland waters. Especially for mid-sized or small rivers this is a considerable challenge imposing insurmountable logistical efforts and costs. It is therefore investigated if large-scale surveying of a river system on an operational basis is feasible by employing airborne hydrographic laser scanning. In cooperation with the Bavarian Water Authority (WWA Weilheim) a pilot project was initiated by the Unit of Hydraulic Engineering at the University of Innsbruck and RIEGL Laser Measurement Systems exploiting the possibilities of a new LIDAR measurement system with high spatial resolution and high measurement rate to capture about 70 km of riverbed and foreland for the river Loisach in Bavaria/Germany and the estuary and parts of the shoreline (about 40km in length) of lake Ammersee. The entire area surveyed was referenced to classic terrestrial cross-section surveys with the aim to derive products for the monitoring and managing needs of the inland water bodies forced by the EU-WFD. The survey was performed in July 2011 by helicopter and airplane and took 3 days in total. In addition, high resolution areal images were taken to provide an optical reference, offering a wide range of possibilities on further research, monitoring, and managing responsibilities. The operating altitude was about 500 m to maintain eye-safety, even for the aided eye, the airspeed was about 55 kts for the helicopter and 75 kts for the aircraft. The helicopter was used in the alpine regions while the fixed wing aircraft was used in the plains and the urban area, using appropriate scan rates to receive evenly distributed point clouds. The resulting point density ranged from 10 to 25 points per square meter. By carefully selecting days with optimum water quality, satisfactory penetration down to the river bed was achieved

  18. Survival rate of airborne Mycobacterium bovis.

    PubMed

    Gannon, B W; Hayes, C M; Roe, J M

    2007-04-01

    Despite years of study the principle transmission route of bovine tuberculosis to cattle remains unresolved. The distribution of pathological lesions, which are concentrated in the respiratory system, and the very low dose of Mycobacterium bovis needed to initiate infection from a respiratory tract challenge suggest that the disease is spread by airborne transmission. Critical to the airborne transmission of a pathogenic microorganism is its ability to survive the stresses incurred whilst airborne. This study demonstrates that M. bovis is resistant to the stresses imposed immediately after becoming airborne, 94% surviving the first 10 min after aerosolisation. Once airborne the organism is robust, its viability decreasing with a half-life of approximately 1.5 hours. These findings support the hypothesis that airborne transmission is the principle route of infection for bovine tuberculosis. PMID:17045316

  19. Tracking Cancer Genetic Evolution using OncoTrack

    PubMed Central

    Talukder, Asoke K.; Agarwal, Mahima; Buetow, Kenneth H.; Denèfle, Patrice P.

    2016-01-01

    It is difficult for existing methods to quantify, and track the constant evolution of cancers due to high heterogeneity of mutations. However, structural variations associated with nucleotide number changes show repeatable patterns in localized regions of the genome. Here we introduce SPKMG, which generalizes nucleotide number based properties of genes, in statistical terms, at the genome-wide scale. It is measured from the normalized amount of aligned NGS reads in exonic regions of a gene. SPKMG values are calculated within OncoTrack. SPKMG values being continuous numeric variables provide a statistical metric to track DNA level changes. We show that SPKMG measures of cancer DNA show a normative pattern at the genome-wide scale. The analysis leads to the discovery of core cancer genes and also provides novel dynamic insights into the stage of cancer, including cancer development, progression, and metastasis. This technique will allow exome data to also be used for quantitative LOH/CNV analysis for tracking tumour progression and evolution with a higher efficiency. PMID:27412732

  20. Tracking Cancer Genetic Evolution using OncoTrack.

    PubMed

    Talukder, Asoke K; Agarwal, Mahima; Buetow, Kenneth H; Denèfle, Patrice P

    2016-01-01

    It is difficult for existing methods to quantify, and track the constant evolution of cancers due to high heterogeneity of mutations. However, structural variations associated with nucleotide number changes show repeatable patterns in localized regions of the genome. Here we introduce SPKMG, which generalizes nucleotide number based properties of genes, in statistical terms, at the genome-wide scale. It is measured from the normalized amount of aligned NGS reads in exonic regions of a gene. SPKMG values are calculated within OncoTrack. SPKMG values being continuous numeric variables provide a statistical metric to track DNA level changes. We show that SPKMG measures of cancer DNA show a normative pattern at the genome-wide scale. The analysis leads to the discovery of core cancer genes and also provides novel dynamic insights into the stage of cancer, including cancer development, progression, and metastasis. This technique will allow exome data to also be used for quantitative LOH/CNV analysis for tracking tumour progression and evolution with a higher efficiency. PMID:27412732

  1. Saturation of repeated quantum measurements

    NASA Astrophysics Data System (ADS)

    Haapasalo, Erkka; Heinosaari, Teiko; Kuramochi, Yui

    2016-08-01

    We study sequential measurement scenarios where the system is repeatedly subjected to the same measurement process. We first provide examples of such repeated measurements where further repetitions of the measurement do not increase our knowledge on the system after some finite number of measurement steps. We also prove, however, that repeating the Lüders measurement of an unsharp two-outcome observable never saturates in this sense, and we characterize the observable measured in the limit of infinitely many repetitions. Our result implies that a repeated measurement can be used to correct the inherent noise of an unsharp observable.

  2. Radio tracking system

    NASA Technical Reports Server (NTRS)

    Breidenthal, J. C.; Komarek, T. A.

    1982-01-01

    The principles and techniques of deep space radio tracking are described along with the uses of tracking data in navigation and radio science. Emphasis is placed on the measurement functions of radio tracking.

  3. Application of Airborne Sea Ice Observations Towards Improving Satellite-based Products

    NASA Astrophysics Data System (ADS)

    Tschudi, M. A.; Baldwin, D.; Liu, Y.; Dworak, R.; Key, J.

    2015-12-01

    Recent airborne and satellite observations suggest large decreases in Arctic sea ice thickness in recent years, but uncertainty remains in terms of overall loss of ice mass versus redistribution of mass within the Arctic Basin. In general though, the combination of airborne and satellite observations tend to agree that some thinning of the ice cover has occurred. In addition to changes in ice thickness and mass, other related changes in properties are likely if the ice pack is undergoing fundamental changes such as a shift to a largely seasonal sea-ice cover. Therefore, it is imperative to utilize airborne and surface-based observations to evaluate satellite-based sea ice products and to improve algorithms that estimate sea ice properties. Sea ice surface properties derived from NASA's Operation IceBridge (OIB) airborne measurements are currently being used to evaluate and update Suomi-NPP VIIRS sea ice products. Estimates of ice thickness derived from the OIB observations may be used to establish a relationship between sea ice thickness and the age of the ice. Drifting buoys serve to improve errors in tracking the movement of ice parcels through Arctic waters. Future airborne measurements of spectral reflectance during the melt season will improve algorithms that estimate melt pond fraction. We present examples of airborne validation of VIIRS sea ice products, relationships between sea ice thickness estimated from OIB measurements and sea ice age, and demonstrate the need for future airborne high-resolution estimates of surface reflectance, particularly in melt ponds. OIB thickness estimates over one sea ice age cell (12.5 km box) are shown in the attached figure.

  4. Assessment of the Levels of Airborne Bacteria, Gram-Negative Bacteria, and Fungi in Hospital Lobbies

    PubMed Central

    Park, Dong-Uk; Yeom, Jeong-Kwan; Lee, Won Jae; Lee, Kyeong-Min

    2013-01-01

    Aims: We assessed the levels of airborne bacteria, Gram-negative bacteria (GNB), and fungi in six hospital lobbies, and investigated the environmental and hospital characteristics that affected the airborne microorganism levels. Methods: An Andersen single-stage sampler equipped with appropriate nutrition plate agar was used to collect the samples. The three types of microorganisms were repeatedly collected at a fixed location in each hospital (assumed to be representative of the entire hospital lobby) from 08:00 through 24:00, with a sampling time of less than 5 min. Temperature and relative humidity were simultaneously monitored. Results: Multiple regression analysis was used to identify the major factors affecting microorganism levels. The average levels of bacteria (7.2 × 102 CFU/m3), GNB (1.7 × 10 CFU/m3), and fungi (7.7 × 10 CFU/m3) indicated that all hospital lobbies were generally contaminated. Season was the only factor that significantly affected the levels of all microorganisms (p < 0.0001), where contamination was the highest during the summer, significantly higher than during the winter. Other significant factors varied by microorganism, as follows: airborne bacteria (number of people in the lobby, sampling time), GNB (scale of hospital), and fungi (humidity and air temperature). Conclusions: Hospital lobby air was generally contaminated with microorganisms, including bacteria, GNB, and fungi. Environmental factors that may significantly influence the airborne concentrations of these agents should be managed to minimize airborne levels. PMID:23435586

  5. The Airborne Conical Scanning Millimeter-Wave Imaging Radiometer (CoSMIR)

    NASA Technical Reports Server (NTRS)

    Piepmeier, J. R.; Manning, W.; Wang, J. R.; Racette, P.; Krebs, Carolyn A. (Technical Monitor)

    2002-01-01

    Results of the first science flight of the airborne Conical Scanning Millimeter-wave Imaging Radiometer (CoSMIR) for high-altitude observations from the NASA ER-2 is discussed. Imagery collected from the flight demonstrates CoSMIR's unique conical/cross-track imaging mode and provides comparison of CoSMIR measurements to those of the Special Sensor Microwave/Temperature-2 (SSM/T-2) satellite radiometer.

  6. Ground target tracking and road map extraction

    NASA Astrophysics Data System (ADS)

    Koch, W.; Koller, J.; Ulmke, M.

    For analyzing dynamic scenarios with many ground moving vehicles, airborne Ground Moving Target Indicator (GMTI) radar is well-suited due to its wide-area, all-weather, day/night, and real time capabilities. The generation of GMTI tracks from these data is the backbone for ground surveillance and traffic flow analysis. In case of dense target situations, missing detections and false alarms, Multi-Hypotheses Tracking (MHT) is the method at choice to solve the inherent ambiguities in the data-targets assignment problem. The resulting MHT-tracks are suited to extract road map information which is highly up-to-date and fairly precise. Moreover, their accuracy is quantitatively described. The precision of the extracted road segments can be improved significantly using smoothed or retrodicted tracks. In turn, the extracted road information is exploited for the precise tracking of succeeding road targets. The proposed, fully Bayesian approach is illustrated by a simulated example including Doppler and terrain obscuration, providing hints to the achievable road map accuracies.

  7. A gunner model for an AAA tracking task with interrupted observations

    NASA Technical Reports Server (NTRS)

    Yu, C. F.; Wei, K. C.; Vikmanis, M.

    1982-01-01

    The problem of modeling a trained human operator's tracking performance in an anti-aircraft system under various display blanking conditions is discussed. The input to the gunner is the observable tracking error subjected to repeated interruptions (blanking). A simple and effective gunner model was developed. The effect of blanking on the gunner's tracking performance is approached via modeling the observer and controller gains.

  8. All-photonic quantum repeaters

    PubMed Central

    Azuma, Koji; Tamaki, Kiyoshi; Lo, Hoi-Kwong

    2015-01-01

    Quantum communication holds promise for unconditionally secure transmission of secret messages and faithful transfer of unknown quantum states. Photons appear to be the medium of choice for quantum communication. Owing to photon losses, robust quantum communication over long lossy channels requires quantum repeaters. It is widely believed that a necessary and highly demanding requirement for quantum repeaters is the existence of matter quantum memories. Here we show that such a requirement is, in fact, unnecessary by introducing the concept of all-photonic quantum repeaters based on flying qubits. In particular, we present a protocol based on photonic cluster-state machine guns and a loss-tolerant measurement equipped with local high-speed active feedforwards. We show that, with such all-photonic quantum repeaters, the communication efficiency scales polynomially with the channel distance. Our result paves a new route towards quantum repeaters with efficient single-photon sources rather than matter quantum memories. PMID:25873153

  9. Sequence repeats and protein structure

    NASA Astrophysics Data System (ADS)

    Hoang, Trinh X.; Trovato, Antonio; Seno, Flavio; Banavar, Jayanth R.; Maritan, Amos

    2012-11-01

    Repeats are frequently found in known protein sequences. The level of sequence conservation in tandem repeats correlates with their propensities to be intrinsically disordered. We employ a coarse-grained model of a protein with a two-letter amino acid alphabet, hydrophobic (H) and polar (P), to examine the sequence-structure relationship in the realm of repeated sequences. A fraction of repeated sequences comprises a distinct class of bad folders, whose folding temperatures are much lower than those of random sequences. Imperfection in sequence repetition improves the folding properties of the bad folders while deteriorating those of the good folders. Our results may explain why nature has utilized repeated sequences for their versatility and especially to design functional proteins that are intrinsically unstructured at physiological temperatures.

  10. All-photonic quantum repeaters

    NASA Astrophysics Data System (ADS)

    Azuma, Koji; Tamaki, Kiyoshi; Lo, Hoi-Kwong

    2015-04-01

    Quantum communication holds promise for unconditionally secure transmission of secret messages and faithful transfer of unknown quantum states. Photons appear to be the medium of choice for quantum communication. Owing to photon losses, robust quantum communication over long lossy channels requires quantum repeaters. It is widely believed that a necessary and highly demanding requirement for quantum repeaters is the existence of matter quantum memories. Here we show that such a requirement is, in fact, unnecessary by introducing the concept of all-photonic quantum repeaters based on flying qubits. In particular, we present a protocol based on photonic cluster-state machine guns and a loss-tolerant measurement equipped with local high-speed active feedforwards. We show that, with such all-photonic quantum repeaters, the communication efficiency scales polynomially with the channel distance. Our result paves a new route towards quantum repeaters with efficient single-photon sources rather than matter quantum memories.

  11. All-photonic quantum repeaters.

    PubMed

    Azuma, Koji; Tamaki, Kiyoshi; Lo, Hoi-Kwong

    2015-01-01

    Quantum communication holds promise for unconditionally secure transmission of secret messages and faithful transfer of unknown quantum states. Photons appear to be the medium of choice for quantum communication. Owing to photon losses, robust quantum communication over long lossy channels requires quantum repeaters. It is widely believed that a necessary and highly demanding requirement for quantum repeaters is the existence of matter quantum memories. Here we show that such a requirement is, in fact, unnecessary by introducing the concept of all-photonic quantum repeaters based on flying qubits. In particular, we present a protocol based on photonic cluster-state machine guns and a loss-tolerant measurement equipped with local high-speed active feedforwards. We show that, with such all-photonic quantum repeaters, the communication efficiency scales polynomially with the channel distance. Our result paves a new route towards quantum repeaters with efficient single-photon sources rather than matter quantum memories. PMID:25873153

  12. Estimating repeatability of egg size

    USGS Publications Warehouse

    Flint, P.L.; Rockwell, R.F.; Sedinger, J.S.

    2001-01-01

    Measures of repeatability have long been used to assess patterns of variation in egg size within and among females. We compared different analytical approaches for estimating repeatability of egg size of Black Brant. Separate estimates of repeatability for eggs of each clutch size and laying sequence number varied from 0.49 to 0.64. We suggest that using the averaging egg size within clutches results in underestimation of variation within females and thereby overestimates repeatability. We recommend a nested design that partitions egg-size variation within clutches, among clutches within females, and among females. We demonstrate little variation in estimates of repeatability resulting from a nested model controlling for egg laying sequence and a nested model in which we assumed laying sequence was unknown.

  13. Geophex airborne unmanned survey system

    SciTech Connect

    Won, I.J.; Taylor, D.W.A.

    1995-03-01

    The purpose of this effort is to design, construct, and evaluate a portable, remotely-piloted, airborne, geophysical survey system. This nonintrusive system will provide {open_quotes}stand-off{close_quotes} capability to conduct surveys and detect buried objects, structures, and conditions of interest at hazardous locations. This system permits two operators to rapidly conduct geophysical characterization of hazardous environmental sites. During a survey, the operators remain remote from, but within visual distance, of, the site. The sensor system never contacts the Earth, but can be positioned near the ground so that weak anomalies can be detected.

  14. Airborne wavemeter validation and calibration

    NASA Technical Reports Server (NTRS)

    Goad, Joseph H., Jr.; Rinsland, Pamela L.; Kist, Edward H., Jr.; Geier, Erika B.; Banziger, Curtis G.

    1992-01-01

    This manuscript outlines a continuing effort to validate and verify the performance of an airborne autonomous wavemeter for tuning solid state lasers to a desired wavelength. The application is measuring the vertical profiles of atmospheric water vapor using a differential absorption lidar (DIAL) technique. Improved wavemeter performance data for varying ambient temperatures are presented. This resulted when the electronic grounding and shielding were improved. The results with short pulse duration lasers are also included. These lasers show that similar performance could be obtained with lasers operating in the continuous and the pulsed domains.

  15. High sensitive airborne radioiodine monitor.

    PubMed

    Ogata, Yoshimune; Yamasaki, Tadashi; Hanafusa, Ryuji

    2013-11-01

    Airborne radioiodine monitoring includes a problem in that commercial radioactive gas monitors have inadequate sensitivity. To solve this problem, we designed a highly sensitive monitoring system. The higher counting efficiency and lower background made it possible to perform the low-level monitoring. The characteristics of the system were investigated using gaseous (125)I. The minimum detectable activity concentration was 1 × 10(-4)Bq cm(-3) for 1 min counting, which is one tenth of the legal limit for the radiation controlled areas in Japan. PMID:23602709

  16. Geophex Airborne Unmanned Survey System

    SciTech Connect

    Won, I.J.; Keiswetter, D.

    1995-10-01

    The purpose of this effort is to design, construct, and evaluate a portable, remotely-piloted, airborne, geophysical survey system. This non-intrusive system will provide {open_quotes}stand-off{close_quotes} capability to conduct surveys and detect buried objects, structures, and conditions of interest at hazardous locations. This system permits rapid geophysical characterization of hazardous environmental sites. During a survey, the operators remain remote from, but within visual distance of, the site. The sensor system never contacts the Earth, but can be positioned near the ground so that weak geophysical anomalies can be detected.

  17. Cyberinfrastructure for Airborne Sensor Webs

    NASA Technical Reports Server (NTRS)

    Freudinger, Lawrence C.

    2009-01-01

    Since 2004 the NASA Airborne Science Program has been prototyping and using infrastructure that enables researchers to interact with each other and with their instruments via network communications. This infrastructure uses satellite links and an evolving suite of applications and services that leverage open-source software. The use of these tools has increased near-real-time situational awareness during field operations, resulting in productivity improvements and the collection of better data. This paper describes the high-level system architecture and major components, with example highlights from the use of the infrastructure. The paper concludes with a discussion of ongoing efforts to transition to operational status.

  18. Biological monitoring of airborne pollution

    SciTech Connect

    Ditz, D.W. )

    1990-01-01

    Common plants such as grasses, mosses, and even goldenrod may turn out to have a new high-tech role as monitors of airborne pollution from solid waste incinerators. Certain plants that respond to specific pollutants can provide continuous surveillance of air quality over long periods of time: they are bio-indicators. Other species accumulate pollutants and can serve as sensitive indicators of pollutants and of food-chain contamination: they are bio-accumulators. Through creative use of these properties, biological monitoring can provide information that cannot be obtained by current methods such as stack testing.

  19. Airborne Research Experience for Educators

    NASA Astrophysics Data System (ADS)

    Costa, V. B.; Albertson, R.; Smith, S.; Stockman, S. A.

    2009-12-01

    The Airborne Research Experience for Educators (AREE) Program, conducted by the NASA Dryden Flight Research Center Office of Education in partnership with the AERO Institute, NASA Teaching From Space Program, and California State University Fullerton, is a complete end-to-end residential research experience in airborne remote sensing and atmospheric science. The 2009 program engaged ten secondary educators who specialize in science, technology, engineering or mathematics in a 6-week Student Airborne Research Program (SARP) offered through NSERC. Educators participated in collection of in-flight remote sensor data during flights aboard the NASA DC-8 as well as in-situ research on atmospheric chemistry (bovine emissions of methane); algal blooms (remote sensing to determine location and degree of blooms for further in-situ analysis); and crop classification (exploration of how drought conditions in Central California have impacted almond and cotton crops). AREE represents a unique model of the STEM teacher-as-researcher professional development experience because it asks educators to participate in a research experience and then translate their experiences into classroom practice through the design, implementation, and evaluation of instructional materials that emphasize the scientific research process, inquiry-based investigations, and manipulation of real data. Each AREE Master Educator drafted a Curriculum Brief, Teachers Guide, and accompanying resources for a topic in their teaching assignment Currently, most professional development programs offer either a research experience OR a curriculum development experience. The dual nature of the AREE model engaged educators in both experiences. Educators’ content and pedagogical knowledge of STEM was increased through the review of pertinent research articles during the first week, attendance at lectures and workshops during the second week, and participation in the airborne and in-situ research studies, data

  20. Detection of multiple airborne targets from multisensor data

    NASA Astrophysics Data System (ADS)

    Foltz, Mark A.; Srivastava, Anuj; Miller, Michael I.; Grenander, Ulf

    1995-08-01

    Previously we presented a jump-diffusion based random sampling algorithm for generating conditional mean estimates of scene representations for the tracking and recongition of maneuvering airborne targets. These representations include target positions and orientations along their trajectories and the target type associated with each trajectory. Taking a Bayesian approach, a posterior measure is defined on the parameter space by combining sensor models with a sophisticated prior based on nonlinear airplane dynamics. The jump-diffusion algorithm constructs a Markov process which visits the elements of the parameter space with frequencies proportional to the posterior probability. It consititutes both the infinitesimal, local search via a sample path continuous diffusion transform and the larger, global steps through discrete jump moves. The jump moves involve the addition and deletion of elements from the scene configuration or changes in the target type assoviated with each target trajectory. One such move results in target detection by the addition of a track seed to the inference set. This provides initial track data for the tracking/recognition algorithm to estimate linear graph structures representing tracks using the other jump moves and the diffusion process, as described in our earlier work. Target detection ideally involves a continuous research over a continuum of the observation space. In this work we conclude that for practical implemenations the search space must be discretized with lattice granularity comparable to sensor resolution, and discuss how fast Fourier transforms are utilized for efficient calcuation of sufficient statistics given our array models. Some results are also presented from our implementation on a networked system including a massively parallel machine architecture and a silicon graphics onyx workstation.

  1. Airborne Visible Laser Optical Communications Program (AVLOC)

    NASA Technical Reports Server (NTRS)

    Ward, J. H.

    1975-01-01

    The design, development, and operation of airborne and ground-based laser communications and laser radar hardware is described in support of the Airborne Visible Laser Optical Communication program. The major emphasis is placed on the development of a highly flexible test bed for the evaluation of laser communications systems techniques and components in an operational environment.

  2. Global Test Range: Toward Airborne Sensor Webs

    NASA Technical Reports Server (NTRS)

    Mace, Thomas H.; Freudinger, Larry; DelFrate John H.

    2008-01-01

    This viewgraph presentation reviews the planned global sensor network that will monitor the Earth's climate, and resources using airborne sensor systems. The vision is an intelligent, affordable Earth Observation System. Global Test Range is a lab developing trustworthy services for airborne instruments - a specialized Internet Service Provider. There is discussion of several current and planned missions.

  3. Airborne Relay-Based Regional Positioning System

    PubMed Central

    Lee, Kyuman; Noh, Hongjun; Lim, Jaesung

    2015-01-01

    Ground-based pseudolite systems have some limitations, such as low vertical accuracy, multipath effects and near-far problems. These problems are not significant in airborne-based pseudolite systems. However, the monitoring of pseudolite positions is required because of the mobility of the platforms on which the pseudolites are mounted, and this causes performance degradation. To address these pseudolite system limitations, we propose an airborne relay-based regional positioning system that consists of a master station, reference stations, airborne relays and a user. In the proposed system, navigation signals are generated from the reference stations located on the ground and are relayed via the airborne relays. Unlike in conventional airborne-based systems, the user in the proposed system sequentially estimates both the locations of airborne relays and his/her own position. Therefore, a delay due to monitoring does not occur, and the accuracy is not affected by the movement of airborne relays. We conducted several simulations to evaluate the performance of the proposed system. Based on the simulation results, we demonstrated that the proposed system guarantees a higher accuracy than airborne-based pseudolite systems, and it is feasible despite the existence of clock offsets among reference stations. PMID:26029953

  4. The Continuous wavelet in airborne gravimetry

    NASA Astrophysics Data System (ADS)

    Liang, X.; Liu, L.

    2013-12-01

    Airborne gravimetry is an efficient method to recover medium and high frequency band of earth gravity over any region, especially inaccessible areas, which can measure gravity data with high accuracy,high resolution and broad range in a rapidly and economical way, and It will play an important role for geoid and geophysical exploration. Filtering methods for reducing high-frequency errors is critical to the success of airborne gravimetry due to Aircraft acceleration determination based on GPS.Tradiontal filters used in airborne gravimetry are FIR,IIR filer and so on. This study recommends an improved continuous wavelet to process airborne gravity data. Here we focus on how to construct the continuous wavelet filters and show their working principle. Particularly the technical parameters (window width parameter and scale parameter) of the filters are tested. Then the raw airborne gravity data from the first Chinese airborne gravimetry campaign are filtered using FIR-low pass filter and continuous wavelet filters to remove the noise. The comparison to reference data is performed to determinate external accuracy, which shows that continuous wavelet filters applied to airborne gravity in this thesis have good performances. The advantages of the continuous wavelet filters over digital filters are also introduced. The effectiveness of the continuous wavelet filters for airborne gravimetry is demonstrated through real data computation.

  5. A Simple Method for Collecting Airborne Pollen

    ERIC Educational Resources Information Center

    Kevan, Peter G.; DiGiovanni, Franco; Ho, Rong H.; Taki, Hisatomo; Ferguson, Kristyn A.; Pawlowski, Agata K.

    2006-01-01

    Pollination is a broad area of study within biology. For many plants, pollen carried by wind is required for successful seed set. Airborne pollen also affects human health. To foster studies of airborne pollen, we introduce a simple device--the "megastigma"--for collecting pollen from the air. This device is flexible, yielding easily obtained data…

  6. Airborne Oceanographic Lidar (AOL) (Global Carbon Cycle)

    NASA Technical Reports Server (NTRS)

    2003-01-01

    This bimonthly contractor progress report covers the operation, maintenance and data management of the Airborne Oceanographic Lidar and the Airborne Topographic Mapper. Monthly activities included: mission planning, sensor operation and calibration, data processing, data analysis, network development and maintenance and instrument maintenance engineering and fabrication.

  7. Meeting Review: Airborne Aerosol Inlet Workshop

    NASA Technical Reports Server (NTRS)

    Baumgardner, Darrel; Huebert, Barry; Wilson, Chuck

    1991-01-01

    Proceedings from the Airborne Aerosol Inlet Workshop are presented. The two central topics of discussion were the role of aerosols in atmospheric processes and the difficulties in characterizing aerosols. The following topics were discussed during the working sessions: airborne observations to date; identification of inlet design issues; inlet modeling needs and directions; objectives for aircraft experiments; and future laboratory and wind tunnel studies.

  8. Refining the continuous tracking paradigm to investigate implicit motor learning.

    PubMed

    Zhu, F F; Poolton, J M; Maxwell, J P; Fan, J K M; Leung, G K K; Masters, R S W

    2014-01-01

    In two experiments we investigated factors that undermine conclusions about implicit motor learning in the continuous tracking paradigm. In Experiment 1, we constructed a practice phase in which all three segments of the waveform pattern were random, in order to examine whether tracking performance decreased as a consequence of time spent on task. Tracking error was lower in the first segment than in the middle segment and lower in the middle segment than in the final segment, indicating that tracking performance decreased as a function of increasing time-on-task. In Experiment 2, the waveform pattern presented in the middle segment was identical in each trial of practice. In a retention test, tracking performance on the repeated segment was superior to tracking performance on the random segments of the waveform. Furthermore, substitution of the repeated pattern with a random pattern (in a transfer test) resulted in a significantly increased tracking error. These findings imply that characteristics of the repeated pattern were learned. Crucially, tests of pattern recognition implied that participants were not explicitly aware of the presence of a recurring segment of waveform. Recommendations for refining the continuous tracking paradigm for implicit learning research are proposed. PMID:24149243

  9. Repeat-pass InSAR processing for Vegetation Height Calculation: Theory and a validated example

    NASA Astrophysics Data System (ADS)

    Siqueira, P.; Lei, Y.

    2014-12-01

    Knowledge of the vegetation height for a forested region is often used as a proxy for stem volume, biomass, and for characterizing habitats of a variety of plant and animal species. For this reason, remote sensing measures available from stereography, lidar, and InSAR have been important tools for airborne and spaceborne platforms. Among these and other candidates for measuring vegetation heights, InSAR has the advantage of achieving wide coverage areas (on the order of 100 km in cross-track swath) over short time periods, thus making it practical for large-scale assessments of the global environment. The determination of forest stand height (FSH), which is an assessment made on the order of one to ten hectares of resolution, InSAR can provide measures that are proportional to FSH. These are: 1.) interferometric phase compared to a known DEM, preferably of the bald earth, 2.) interferometric correlation (polarimetric or otherwise), which is related to the volume scattering nature of the target, and 3.) interferometric correlation which is related to the temporal decorrelation of the target. Of these, while the volumetric aspect of interferometric correlation is of keen interest, because of the dominant error source of temporal decorrelation, it comes at the cost of the need to perform single-pass interferometry. While such satellite systems do exist (notably the TanDEM-X mission), for vegetation applications, lower frequency systems such as ALOS-1 and -2, and the future NASA radar mission at L-band, provides better signal returns from throughout the vegetation canopy. Hence, rather than relying on volumetric correlation to provide the desired FSH signature, repeat-pass observations of temporal decorrelation are coupled with a vegetation model for this decorrelation to determine the vegetation height. In order to demonstrate this technique, the University of Massachusetts has used 46-day repeat-pass ALOS data to estimate FSH over the US State of Maine, nearly a 10

  10. A theoretical model for airborne radars

    NASA Astrophysics Data System (ADS)

    Faubert, D.

    1989-11-01

    This work describes a general theory for the simulation of airborne (or spaceborne) radars. It can simulate many types of systems including Airborne Intercept and Airborne Early Warning radars, airborne missile approach warning systems etc. It computes the average Signal-to-Noise ratio at the output of the signal processor. In this manner, one obtains the average performance of the radar without having to use Monte Carlo techniques. The model has provision for a waveform without frequency modulation and one with linear frequency modulation. The waveform may also have frequency hopping for Electronic Counter Measures or for clutter suppression. The model can accommodate any type of encounter including air-to-air, air-to-ground (look-down) and rear attacks. It can simulate systems with multiple phase centers on receive for studying advanced clutter or jamming interference suppression techniques. An Airborne Intercept radar is investigated to demonstrate the validity and the capability of the model.

  11. Solar tracking system

    DOEpatents

    Okandan, Murat; Nielson, Gregory N.

    2016-07-12

    Solar tracking systems, as well as methods of using such solar tracking systems, are disclosed. More particularly, embodiments of the solar tracking systems include lateral supports horizontally positioned between uprights to support photovoltaic modules. The lateral supports may be raised and lowered along the uprights or translated to cause the photovoltaic modules to track the moving sun.

  12. Geophex Airborne Unmanned Survey System

    SciTech Connect

    Won, I.L.; Keiswetter, D.

    1995-12-31

    Ground-based surveys place personnel at risk due to the proximity of buried unexploded ordnance (UXO) items or by exposure to radioactive materials and hazardous chemicals. The purpose of this effort is to design, construct, and evaluate a portable, remotely-piloted, airborne, geophysical survey system. This non-intrusive system will provide stand-off capability to conduct surveys and detect buried objects, structures, and conditions of interest at hazardous locations. During a survey, the operators remain remote from, but within visual distance of, the site. The sensor system never contacts the Earth, but can be positioned near the ground so that weak geophysical anomalies can be detected. The Geophex Airborne Unmanned Survey System (GAUSS) is designed to detect and locate small-scale anomalies at hazardous sites using magnetic and electromagnetic survey techniques. The system consists of a remotely-piloted, radio-controlled, model helicopter (RCH) with flight computer, light-weight geophysical sensors, an electronic positioning system, a data telemetry system, and a computer base-station. The report describes GAUSS and its test results.

  13. Bayesian Tracking of Emerging Epidemics Using Ensemble Optimal Statistical Interpolation

    PubMed Central

    Cobb, Loren; Krishnamurthy, Ashok; Mandel, Jan; Beezley, Jonathan D.

    2014-01-01

    We present a preliminary test of the Ensemble Optimal Statistical Interpolation (EnOSI) method for the statistical tracking of an emerging epidemic, with a comparison to its popular relative for Bayesian data assimilation, the Ensemble Kalman Filter (EnKF). The spatial data for this test was generated by a spatial susceptible-infectious-removed (S-I-R) epidemic model of an airborne infectious disease. Both tracking methods in this test employed Poisson rather than Gaussian noise, so as to handle epidemic data more accurately. The EnOSI and EnKF tracking methods worked well on the main body of the simulated spatial epidemic, but the EnOSI was able to detect and track a distant secondary focus of infection that the EnKF missed entirely. PMID:25113590

  14. SOFIA tracking subsystem: results of assembly, operation, and calibration tests

    NASA Astrophysics Data System (ADS)

    Bittner, Hermann; Erdmann, Matthias; Schmolke, Juergen; Lattner, Klaus; Levin, Torsten; Erhard, Markus

    2003-02-01

    The SOFIA airborne telescope has a Tracking Subsystem for stellar acquisition, tracking, and pointing. The system has three high-performance imagers: the boresighted wide field (6 degrees FOV) and fine field imagers (70 arcminutes FOV), and the main-telescope-optics sharing focal plane imager (8 arcminutes FOV). The imagers are controlled by 3 CCD head controllers, an overall imager controller, and a tracker controller providing the tracking error signals from the objects observed by the imagers. There have been several test steps in the assembly, integration, and verification of the Tracking Subsystem. The paper presents the fully integrated system as actually built, the results of the thermal-vacuum and vibration tests of the fine field imager, the tested operational/functional S/W performance, as well as the results of the geometric and radiometric calibrations of the imagers.

  15. Heterogeneous Multiple Sensors Joint Tracking of Maneuvering Target in Clutter

    PubMed Central

    Wu, Panlong; Li, Xingxiu; Kong, Jianshou; Liu, Jiale

    2015-01-01

    To solve the problem of tracking maneuvering airborne targets in the presence of clutter, an improved interacting multiple model probability data association algorithm (IMMPDA-MDCM) using radar/IR sensors fusion is proposed. Under the architecture of the proposed algorithm, the radar/IR centralized fusion tracking scheme of IMMPDA-MDCM is designed to guarantee the observability of the target state. The interacting multiple model (IMM) deals with the model switching. The modified debiased converted measurement (MDCM) filter accounts for non-linearity in the dynamic system models, and reduces the effect of measurement noise on the covariance effectively. The probability data association (PDA) handles data association and measurement uncertainties in clutter. The simulation results show that the proposed algorithm can improve the tracking precision for maneuvering target in clutters, and has higher tracking precision than the traditional IMMPDA based on EKF and IMMPDA based on DCM algorithm. PMID:26193279

  16. Bayesian tracking of emerging epidemics using ensemble optimal statistical interpolation.

    PubMed

    Cobb, Loren; Krishnamurthy, Ashok; Mandel, Jan; Beezley, Jonathan D

    2014-07-01

    We present a preliminary test of the Ensemble Optimal Statistical Interpolation (EnOSI) method for the statistical tracking of an emerging epidemic, with a comparison to its popular relative for Bayesian data assimilation, the Ensemble Kalman Filter (EnKF). The spatial data for this test was generated by a spatial susceptible-infectious-removed (S-I-R) epidemic model of an airborne infectious disease. Both tracking methods in this test employed Poisson rather than Gaussian noise, so as to handle epidemic data more accurately. The EnOSI and EnKF tracking methods worked well on the main body of the simulated spatial epidemic, but the EnOSI was able to detect and track a distant secondary focus of infection that the EnKF missed entirely. PMID:25113590

  17. Simulation of multistatic and backscattering cross sections for airborne radar

    NASA Astrophysics Data System (ADS)

    Biggs, Albert W.

    1986-07-01

    In order to determine susceptibilities of airborne radar to electronic countermeasures and electronic counter-countermeasures simulations of multistatic and backscattering cross sections were developed as digital modules in the form of algorithms. Cross section algorithms are described for prolate (cigar shape) and oblate (disk shape) spheroids. Backscattering cross section algorithms are also described for different categories of terrain. Backscattering cross section computer programs were written for terrain categorized as vegetation, sea ice, glacial ice, geological (rocks, sand, hills, etc.), oceans, man-made structures, and water bodies. PROGRAM SIGTERRA is a file for backscattering cross section modules of terrain (TERRA) such as vegetation (AGCROP), oceans (OCEAN), Arctic sea ice (SEAICE), glacial snow (GLASNO), geological structures (GEOL), man-made structures (MAMMAD), or water bodies (WATER). AGCROP describes agricultural crops, trees or forests, prairies or grassland, and shrubs or bush cover. OCEAN has the SLAR or SAR looking downwind, upwind, and crosswind at the ocean surface. SEAICE looks at winter ice and old or polar ice. GLASNO is divided into a glacial ice and snow or snowfields. MANMAD includes buildings, houses, roads, railroad tracks, airfields and hangars, telephone and power lines, barges, trucks, trains, and automobiles. WATER has lakes, rivers, canals, and swamps. PROGRAM SIGAIR is a similar file for airborne targets such as prolate and oblate spheroids.

  18. Protein Repeats from First Principles.

    PubMed

    Turjanski, Pablo; Parra, R Gonzalo; Espada, Rocío; Becher, Verónica; Ferreiro, Diego U

    2016-01-01

    Some natural proteins display recurrent structural patterns. Despite being highly similar at the tertiary structure level, repeating patterns within a single repeat protein can be extremely variable at the sequence level. We use a mathematical definition of a repetition and investigate the occurrences of these in sequences of different protein families. We found that long stretches of perfect repetitions are infrequent in individual natural proteins, even for those which are known to fold into structures of recurrent structural motifs. We found that natural repeat proteins are indeed repetitive in their families, exhibiting abundant stretches of 6 amino acids or longer that are perfect repetitions in the reference family. We provide a systematic quantification for this repetitiveness. We show that this form of repetitiveness is not exclusive of repeat proteins, but also occurs in globular domains. A by-product of this work is a fast quantification of the likelihood of a protein to belong to a family. PMID:27044676

  19. Protein Repeats from First Principles

    PubMed Central

    Turjanski, Pablo; Parra, R. Gonzalo; Espada, Rocío; Becher, Verónica; Ferreiro, Diego U.

    2016-01-01

    Some natural proteins display recurrent structural patterns. Despite being highly similar at the tertiary structure level, repeating patterns within a single repeat protein can be extremely variable at the sequence level. We use a mathematical definition of a repetition and investigate the occurrences of these in sequences of different protein families. We found that long stretches of perfect repetitions are infrequent in individual natural proteins, even for those which are known to fold into structures of recurrent structural motifs. We found that natural repeat proteins are indeed repetitive in their families, exhibiting abundant stretches of 6 amino acids or longer that are perfect repetitions in the reference family. We provide a systematic quantification for this repetitiveness. We show that this form of repetitiveness is not exclusive of repeat proteins, but also occurs in globular domains. A by-product of this work is a fast quantification of the likelihood of a protein to belong to a family. PMID:27044676

  20. Protein Repeats from First Principles

    NASA Astrophysics Data System (ADS)

    Turjanski, Pablo; Parra, R. Gonzalo; Espada, Rocío; Becher, Verónica; Ferreiro, Diego U.

    2016-04-01

    Some natural proteins display recurrent structural patterns. Despite being highly similar at the tertiary structure level, repeating patterns within a single repeat protein can be extremely variable at the sequence level. We use a mathematical definition of a repetition and investigate the occurrences of these in sequences of different protein families. We found that long stretches of perfect repetitions are infrequent in individual natural proteins, even for those which are known to fold into structures of recurrent structural motifs. We found that natural repeat proteins are indeed repetitive in their families, exhibiting abundant stretches of 6 amino acids or longer that are perfect repetitions in the reference family. We provide a systematic quantification for this repetitiveness. We show that this form of repetitiveness is not exclusive of repeat proteins, but also occurs in globular domains. A by-product of this work is a fast quantification of the likelihood of a protein to belong to a family.

  1. Discovering geospatial networks from ambiguous track data

    NASA Astrophysics Data System (ADS)

    Bevington, James E.; Evans, Michael R.; Shekhar, Shashi

    2011-06-01

    Wide area motion imagery (WAMI) sensors increasingly are being used for persistent surveillance of large urban areas. One of the potential uses for such surveillance is the discovery of geo-spatial networks, which are sets of locations linked by repeated traffic flow over an extended period of time. In this work we present a simple method of deriving geo-spatial network links automatically from ambiguous track segments or tracklets. The method avoids making explicit tracklet linking decisions and relies on temporal aggregation to identify the persistent origin-destination location pairs. We present experimental network discovery results using simulated high density track data for a downtown urban setting.

  2. Accuracy of wind measurements using an airborne Doppler lidar

    NASA Technical Reports Server (NTRS)

    Carroll, J. J.

    1986-01-01

    Simulated wind fields and lidar data are used to evaluate two sources of airborne wind measurement error. The system is sensitive to ground speed and track angle errors, with accuracy required of the angle to within 0.2 degrees and of the speed to within 1 knot, if the recovered wind field is to be within five percent of the correct direction and 10 percent of the correct speed. It is found that errors in recovered wind speed and direction are dependent on wind direction relative to the flight path. Recovery of accurate wind fields from nonsimultaneous sampling errors requires that the lidar data be displaced to account for advection so that the intersections are defined by air parcels rather than fixed points in space.

  3. A multisensor system for airborne surveillance of oil pollution

    NASA Technical Reports Server (NTRS)

    Edgerton, A. T.; Ketchal, R.; Catoe, C.

    1973-01-01

    The U.S. Coast Guard is developing a prototype airborne oil surveillance system for use in its Marine Environmental Protection Program. The prototype system utilizes an X-band side-looking radar, a 37-GHz imaging microwave radiometer, a multichannel line scanner, and a multispectral low light level system. The system is geared to detecting and mapping oil spills and potential pollution violators anywhere within a 25 nmi range of the aircraft flight track under all but extreme weather conditions. The system provides for false target discrimination and maximum identification of spilled materials. The system also provides an automated detection alarm, as well as a color display to achieve maximum coupling between the sensor data and the equipment operator.

  4. Airborne Oceanographic Lidar results. Spring removal experiments, April 1985

    SciTech Connect

    Hoge, F.

    1985-06-21

    This document contains the preliminary results from the analysis of data acquired with the NASA Airborne Oceanographic Lidar (AOL) during the recent Spring Removal Experiment (SPREX). A total of four flights were made with the NASA P-3A aircraft in direct support of the SPREX studies. In addition, a single pass extending from the Sargasso Sea, across the Gulf Stream, and into Savannah was flown as the final leg of the ONR sponsored BIOWATT experiment. The relative distribution of surface temperature and the concentration of chlorophyll and phycoerythrin photopigments across the study area are provided. Also included are along track profiles of sea surface temperature and chlorophyll and phycoerythrin fluorescence emission for each of the individual flight lines. Both the chlorophyll and phycoerythrin laser induced fluorescence signals have been normalized by the water Raman backscatter signal and are each expressed as relative ratio's.

  5. The NASA/JPL Airborne Synthetic Aperture Radar System

    NASA Technical Reports Server (NTRS)

    Kim, Yun-Jin; Lou, Yun-Ling; vanZyl, Jakob

    1996-01-01

    The NASA/JPL airborne SAR (AIRSAR) system operates in the fully polarimetric mode at P-, L- and C-band simultaneously or in the interferometric mode in both L- and C-band simultaneously. The system became operational in late 1987 and flew its first mission aboard a DC-8 aircraft operated by NASA's Ames Research Center in Mountain View, California. Since then, the AIRSAR has flown missions every year and acquired images in North, Central and South America, Europe and Australia. In this paper, we will briefly describe the instrument characteristics, the evolution of the various radar modes, the instrument performance, and improvement in the knowledge of the positioning and attitude information of the radar. In addition, we will summarize the progress of the data processing effort especially in the interferometry processing. Finally, we will address the issue of processing and calibrating the cross-track interferometry (XTI) data.

  6. Airborne sensors for detecting large marine debris at sea.

    PubMed

    Veenstra, Timothy S; Churnside, James H

    2012-01-01

    The human eye is an excellent, general-purpose airborne sensor for detecting marine debris larger than 10 cm on or near the surface of the water. Coupled with the human brain, it can adjust for light conditions and sea-surface roughness, track persistence, differentiate color and texture, detect change in movement, and combine all of the available information to detect and identify marine debris. Matching this performance with computers and sensors is difficult at best. However, there are distinct advantages over the human eye and brain that sensors and computers can offer such as the ability to use finer spectral resolution, to work outside the spectral range of human vision, to control the illumination, to process the information in ways unavailable to the human vision system, to provide a more objective and reproducible result, to operate from unmanned aircraft, and to provide a permanent record that can be used for later analysis. PMID:21300380

  7. Airborne imaging spectrometer - A new tool for remote sensing

    NASA Technical Reports Server (NTRS)

    Vane, G.; Goetz, A. F. H.; Wellman, J. B.

    1983-01-01

    The first of a new class of remote sensing instruments is described. The Airborne Imaging Spectrometer represents the first use of two-dimensional area arrays in a scientific application. The instrument images 32 cross-track pixels simultaneously, each in 128 spectral bands in the 1.2 to 2.4 micro region. The IFOV of the instrument is 1.9 mrad and the spectral sampling interval is 9.6 nanometers. Plans include upgrading the detector from the current 32 x 32 element HgCdTe CCD array to a 64 x 64 element array in 1984. Science and engineering data are currently being actively gathered with the instrument.

  8. Airborne imaging spectrometer - A new tool for remote sensing

    NASA Technical Reports Server (NTRS)

    Vane, G.; Goetz, A. F. H.; Wellman, J. B.

    1984-01-01

    The first of a new class of remote sensing instruments is described. The Airborne Imaging Spectrometer represents the first use of two-dimensional integrated infrared area arrays in a scientific application. The instrument images 32 cross-track pixels simultaneously, each in 128 spectral bands in the 1.2- to 2.4-micron region. The IFOV of the instrument is 1.9 mrad/pixel and the spectral sampling interval is 9.6 nm. Plans include upgrading the detector from the current 32 x 32 element HgCdTe CCD array to a 64 x 64 element array in 1985. Science and engineering data are currently being actively gathered with the instrument.

  9. An airborne real-time hyperspectral target detection system

    NASA Astrophysics Data System (ADS)

    Skauli, Torbjorn; Haavardsholm, Trym V.; Kåsen, Ingebjørg; Arisholm, Gunnar; Kavara, Amela; Opsahl, Thomas Olsvik; Skaugen, Atle

    2010-04-01

    An airborne system for hyperspectral target detection is described. The main sensor is a HySpex pushbroom hyperspectral imager for the visible and near-infrared spectral range with 1600 pixels across track, supplemented by a panchromatic line imager. An optional third sensor can be added, either a SWIR hyperspectral camera or a thermal camera. In real time, the system performs radiometric calibration and georeferencing of the images, followed by image processing for target detection and visualization. The current version of the system implements only spectral anomaly detection, based on normal mixture models. Image processing runs on a PC with a multicore Intel processor and an Nvidia graphics processing unit (GPU). The processing runs in a software framework optimized for large sustained data rates. The platform is a Cessna 172 aircraft based close to FFI, modified with a camera port in the floor.

  10. The airborne laser ranging system, its capabilities and applications

    NASA Technical Reports Server (NTRS)

    Kahn, W. D.; Degnan, J. J.; Englar, T. S., Jr.

    1982-01-01

    The airborne laser ranging system is a multibeam short pulse laser ranging system on board an aircraft. It simultaneously measures the distances between the aircraft and six laser retroreflectors (targets) deployed on the Earth's surface. The system can interrogate over 100 targets distributed over an area of 25,000 sq, kilometers in a matter of hours. Potentially, a total of 1.3 million individual range measurements can be made in a six hour flight. The precision of these range measurements is approximately + or - 1 cm. These measurements are used in procedure which is basically an extension of trilateration techniques to derive the intersite vector between the laser ground targets. By repeating the estimation of the intersite vector, strain and strain rate errors can be estimated. These quantities are essential for crustal dynamic studies which include determination and monitoring of regional strain in the vicinity of active fault zones, land subsidence, and edifice building preceding volcanic eruptions.

  11. Plastic Foam Porosity Characterization by Air-Borne Ultrasound

    NASA Astrophysics Data System (ADS)

    Hoffrén, H.; Karppinen, T.; Hæggström, E.

    2006-03-01

    We continue to develop an ultrasonic burst-reflection method for estimating porosity and tortuosity of solid materials. As a first step we report on method design considerations and measurements on polyurethane foams (Sylomer® vibration dampener) with well-defined porosity. The ultrasonic method is experimentally tested by measuring 235 kHz and 600 kHz air-borne ultrasound reflection from a foam surface at two incidence angles. The reflected sound wave from different foam samples (32% - 64% porosity) was compared to a wave that had traveled from the transmitter to the detector without reflection. The ultrasonically estimated sample porosities coincided within 8% with the porosity estimates obtained by a gravimetric reference method. This parallels the uncertainty of the gravimetric method, 8%. The repeatability of the ultrasonic porosity measurements was better than 5%.

  12. Collation of earth resources data collected by ERIM airborne sensors

    NASA Technical Reports Server (NTRS)

    Hasell, P. G., Jr.

    1975-01-01

    Earth resources imagery from nine years of data collection with developmental airborne sensors is cataloged for reference. The imaging sensors include single and multiband line scanners and side-looking radars. The operating wavelengths of the sensors include ultraviolet, visible and infrared band scanners, and X- and L-band radar. Imagery from all bands (radar and scanner) were collected at some sites and many sites had repeated coverage. The multiband scanner data was radiometrically calibrated. Illustrations show how the data can be used in earth resource investigations. References are made to published reports which have made use of the data in completed investigations. Data collection sponsors are identified and a procedure described for gaining access to the data.

  13. Study of radiation characteristic of airborne sensor based on tarps

    NASA Astrophysics Data System (ADS)

    Yu, Xiujuan; Qi, Weijun; Fang, Aiping

    2014-07-01

    The radiation characteristic of aerial sensor directly affects the quantitative application level of sensor data. In order to study the radiation characteristic, we carried out the radiation characteristic test based on ground tarps laid onto the calibration field of image quality in Anyang, Henan. The airborne sensor was calibrated adopting reflectance-based method. 8 gray-scale tarps and 4 tarps of high reflectance were laid onto the calibration field and they were all with better Lambert radiation characteristic and spectral performance uniformity. Preliminary results show that the bias is larger and the effective dynamic range is smaller and the SNR is lower but the linearity and repeatability are better which can be used to test the response performance of the sensor. Overall, the radiation characteristic tarps laid on the calibration field are suitable for the study of in-flight radiation characteristic of the aerial digital sensor.

  14. TrackEye tracking algorithm characterization

    NASA Astrophysics Data System (ADS)

    Valley, Michael T.; Shields, Robert W.; Reed, Jack M.

    2004-10-01

    TrackEye is a film digitization and target tracking system that offers the potential for quantitatively measuring the dynamic state variables (e.g., absolute and relative position, orientation, linear and angular velocity/acceleration, spin rate, trajectory, angle of attack, etc.) for moving objects using captured single or dual view image sequences. At the heart of the system is a set of tracking algorithms that automatically find and quantify the location of user selected image details such as natural test article features or passive fiducials that have been applied to cooperative test articles. This image position data is converted into real world coordinates and rates with user specified information such as the image scale and frame rate. Though tracking methods such as correlation algorithms are typically robust by nature, the accuracy and suitability of each TrackEye tracking algorithm is in general unknown even under good imaging conditions. The challenges of optimal algorithm selection and algorithm performance/measurement uncertainty are even more significant for long range tracking of high-speed targets where temporally varying atmospheric effects degrade the imagery. This paper will present the preliminary results from a controlled test sequence used to characterize the performance of the TrackEye tracking algorithm suite.

  15. TrackEye tracking algorithm characterization.

    SciTech Connect

    Reed, Jack W.; Shields, Rob W; Valley, Michael T.

    2004-08-01

    TrackEye is a film digitization and target tracking system that offers the potential for quantitatively measuring the dynamic state variables (e.g., absolute and relative position, orientation, linear and angular velocity/acceleration, spin rate, trajectory, angle of attack, etc.) for moving objects using captured single or dual view image sequences. At the heart of the system is a set of tracking algorithms that automatically find and quantify the location of user selected image details such as natural test article features or passive fiducials that have been applied to cooperative test articles. This image position data is converted into real world coordinates and rates with user specified information such as the image scale and frame rate. Though tracking methods such as correlation algorithms are typically robust by nature, the accuracy and suitability of each TrackEye tracking algorithm is in general unknown even under good imaging conditions. The challenges of optimal algorithm selection and algorithm performance/measurement uncertainty are even more significant for long range tracking of high-speed targets where temporally varying atmospheric effects degrade the imagery. This paper will present the preliminary results from a controlled test sequence used to characterize the performance of the TrackEye tracking algorithm suite.

  16. Tracking filter algorithm for automatic video tracking

    NASA Astrophysics Data System (ADS)

    McEver, Mark A.; Kimbrell, James E.

    2006-05-01

    In addition to servo control and power amplification, motion control systems for optical tracking pedestals feature capabilities such as electro-optical tracking using an integrated Automatic Video Tracker (AVT) card. An electro-optical system tracking loop is comprised of sensors mounted on a pointing pedestal, an AVT that detects a target in the sensor imagery, and a tracking filter algorithm that commands the pedestal to follow the target. The tracking filter algorithm receives the target boresight error from the AVT and calculates motion demands for the pedestal servo controller. This paper presents a tracking algorithm based on target state estimation using a Kalman filter. The servo demands are based on calculating the Kalman filter state estimate from absolute line-of-sight angles to the target. Simulations are used to compare its performance to tracking loops without tracking filters, and to other tracking filter algorithms, such as rate feedback loops closed around boresight error. Issues such as data latency and sensor alignment error are discussed.

  17. Target tracking for heterogeneous smart sensor networks

    NASA Astrophysics Data System (ADS)

    Bevington, James E.; McDonnell, Timothy X.

    2001-08-01

    Distributed sensor networks will play a key role in the network centric warfighting environments of the future. We envision a ubiquitous sensing `fabric,' comprising sensors distributed over the terrain and carried on manned and unmanned, terrestrial and airborne vehicles. As a complex `system of systems,' this fabric will need to adapt and self-organize to perform a variety of higher-level tasks such as surveillance and target acquisition. The topology and availability of the sensors will be constantly changing, as will the needs of users as dictated by evolving missions and operational environments. In this work, focusing on the task of target tracking, we address approaches for locating and organizing sensing and processing resources and present algorithms for suitably fusing the observations obtained from a varied and changing set of sensors. Run-time discovery and access of new sensing resources are obtained through the use of Java Jini, treating sensing resources as `services' and viewing higher-level processes such as tracking as clients. Algorithms for fusing generic sensor observations for target tracking are based on the extended Kalman filter, while detection and track initiation are based on a new likelihood projection technique. We present results from an implementation of these concepts in a real- time sensor testbed and discuss lessons learned.

  18. Airborne Laser Scanning and Image Processing Techniques for Archaeological Prospection

    NASA Astrophysics Data System (ADS)

    Faltýnová, M.; Nový, P.

    2014-06-01

    Aerial photography was, for decades, an invaluable tool for archaeological prospection, in spite of the limitation of this method to deforested areas. The airborne laser scanning (ALS) method can be nowadays used to map complex areas and suitable complement earlier findings. This article describes visualization and image processing methods that can be applied on digital terrain models (DTMs) to highlight objects hidden in the landscape. Thanks to the analysis of visualized DTM it is possible to understand the landscape evolution including the differentiation between natural processes and human interventions. Different visualization methods were applied on a case study area. A system of parallel tracks hidden in a forest and its surroundings - part of old route called "Devil's Furrow" near the town of Sázava was chosen. The whole area around well known part of Devil's Furrow has not been prospected systematically yet. The data from the airborne laser scanning acquired by the Czech Office for Surveying, Mapping and Cadastre was used. The average density of the point cloud was approximately 1 point/m2 The goal of the project was to visualize the utmost smallest terrain discontinuities, e.g. tracks and erosion furrows, which some were not wholly preserved. Generally we were interested in objects that are clearly not visible in DTMs displayed in the form of shaded relief. Some of the typical visualization methods were tested (shaded relief, aspect and slope image). To get better results we applied image-processing methods that were successfully used on aerial photographs or hyperspectral images in the past. The usage of different visualization techniques on one site allowed us to verify the natural character of the southern part of Devil's Furrow and find formations up to now hidden in the forests.

  19. Multi-mode multistatics for passive/active airborne surveillance

    NASA Astrophysics Data System (ADS)

    Ogrodnik, Robert F.

    1986-07-01

    The increasing performance demands for air surveillance assets, as well as the necessity for continued surveillance operations in the presence of enemy jamming anti-radiation missile (ARM) attacks, have increased interest in passive surveillance, in particular multi-mode passive/active multistatic sensing. The use of noncooperative radiation as illuminators of opportunity combined with passive surveillance electromagnetic support measurement (ESM) sensors opens new horizons to multistatic surveillance from a passive airborne platform. Research and field tests have been conducted on ESM augmented bistatics as well as noncooperative multistatics which support the development of airborne multi-mode passive surveillance technology. This work has been conducted under such programs as the Bistatic Enhanced Altimeter Detection (BEAD) and the noncooperative multistatic Passive Coherent Location (PCL). Both BEAD and PCL technology directly support the receiver, signal processing and target location/tracking operations necessary for passive surveillance. The demonstrated technologies for EM interference rejection and multistatic multi-target tracking and location under PCL provide a promising performance bench mark for passive surveillance in the presence of a complex electromagnetic environment. Passive receiver intercept performance under BEAD has provided a receiver design baseline for both look-down and look-up surveillance applications. The technologies under development in BEAD and PCL are presented along with the field test results and the sensor concepts. In particular, spin-off data such as bistatic look-down clutter, noise-floor limitation of noncooperative multistatics and sensitivity limitations set by passive surveillance using signal intercept techniques and illuminators of opportunity are provided.

  20. NASA COAST and OCEANIA Airborne Missions Support Ecosystem and Water Quality Research in the Coastal Zone

    NASA Astrophysics Data System (ADS)

    Guild, L. S.; Kudela, R. M.; Hooker, S. B.; Morrow, J. H.; Russell, P. B.; Palacios, S. L.; Livingston, J. M.; Negrey, K.; Torres-Perez, J. L.; Broughton, J.

    2014-12-01

    NASA has a continuing requirement to collect high-quality in situ data for the vicarious calibration of current and next generation ocean color satellite sensors and to validate the algorithms that use the remotely sensed observations. Recent NASA airborne missions over Monterey Bay, CA, have demonstrated novel above- and in-water measurement capabilities supporting a combined airborne sensor approach (imaging spectrometer, microradiometers, and a sun photometer). The results characterize coastal atmospheric and aquatic properties through an end-to-end assessment of image acquisition, atmospheric correction, algorithm application, plus sea-truth observations from state-of-the-art instrument systems. The primary goal is to demonstrate the following in support of calibration and validation exercises for satellite coastal ocean color products: 1) the utility of a multi-sensor airborne instrument suite to assess the bio-optical properties of coastal California, including water quality; and 2) the importance of contemporaneous atmospheric measurements to improve atmospheric correction in the coastal zone. The imaging spectrometer (Headwall) is optimized in the blue spectral domain to emphasize remote sensing of marine and freshwater ecosystems. The novel airborne instrument, Coastal Airborne In-situ Radiometers (C-AIR) provides measurements of apparent optical properties with high dynamic range and fidelity for deriving exact water leaving radiances at the land-ocean boundary, including radiometrically shallow aquatic ecosystems. Simultaneous measurements supporting empirical atmospheric correction of image data are accomplished using the Ames Airborne Tracking Sunphotometer (AATS-14). Flight operations are presented for the instrument payloads using the CIRPAS Twin Otter flown over Monterey Bay during the seasonal fall algal bloom in 2011 (COAST) and 2013 (OCEANIA) to support bio-optical measurements of phytoplankton for coastal zone research.

  1. Comparison of Air Impaction and Electrostatic Dust Collector Sampling Methods to Assess Airborne Fungal Contamination in Public Buildings.

    PubMed

    Normand, Anne-Cécile; Ranque, Stéphane; Cassagne, Carole; Gaudart, Jean; Sallah, Kankoé; Charpin, Denis-André; Piarroux, Renaud

    2016-03-01

    Many ailments can be linked to exposure to indoor airborne fungus. However, obtaining a precise measurement of airborne fungal levels is complicated partly due to indoor air fluctuations and non-standardized techniques. Electrostatic dust collector (EDC) sampling devices have been used to measure a wide range of airborne analytes, including endotoxins, allergens, β-glucans, and microbial DNA in various indoor environments. In contrast, viable mold contamination has only been assessed in highly contaminated environments such as farms and archive buildings. This study aimed to assess the use of EDCs, compared with repeated air-impactor measurements, to assess airborne viable fungal flora in moderately contaminated indoor environments. Indoor airborne fungal flora was cultured from EDCs and daily air-impaction samples collected in an office building and a daycare center. The quantitative fungal measurements obtained using a single EDC significantly correlated with the cumulative measurement of nine daily air impactions. Both methods enabled the assessment of fungal exposure, although a few differences were observed between the detected fungal species and the relative quantity of each species. EDCs were also used over a 32-month period to monitor indoor airborne fungal flora in a hospital office building, which enabled us to assess the impact of outdoor events (e.g. ground excavations) on the fungal flora levels on the indoor environment. In conclusion, EDC-based measurements provided a relatively accurate profile of the viable airborne flora present during a sampling period. In particular, EDCs provided a more representative assessment of fungal levels compared with single air-impactor sampling. The EDC technique is also simpler than performing repetitive air-impaction measures over the course of several consecutive days. EDC is a versatile tool for collecting airborne samples and was efficient for measuring mold levels in indoor environments. PMID:26491105

  2. Modis-N airborne simulator

    NASA Technical Reports Server (NTRS)

    Cech, Steven D.

    1992-01-01

    All required work associated with the above referenced contract has been successfully completed at this time. The Modis-N Airborne Simulator has been developed from existing AB184 Wildfire spectrometer parts as well as new detector arrays, optical components, and associated mechanical and electrical hardware. The various instrument components have been integrated into an operational system which has undergone extensive laboratory calibration and testing. The instrument has been delivered to NASA Ames where it will be installed on the NASA ER-2. The following paragraphs detail the specific tasks performed during the contract effort, the results obtained during the integration and testing of the instrument, and the conclusions which can be drawn from this effort.

  3. Airborne imaging spectrometer development tasks

    NASA Astrophysics Data System (ADS)

    Bolten, John

    The tasks that must be completed to design and build an airborne imaging spectrometer are listed. The manpower and resources required to do these tasks must be estimated by the people responsible for that work. The tasks are broken down by instrument subsystem or discipline. The instrument performance can be assessed at various stages during the development. The initial assessment should be done with the preliminary computer model. The instrument calibration facilities should be designed, but no calibration facilities are needed. The intermediate assessment can be done when the front end has been assembled. The preliminary instrument calibration facility should be available at this stage. The final assessment can only be done when the instrument is complete and ready for flight. For this, the final instrument calibration facility and the flight qualification facilities must be ready. The final assessment is discussed in each discipline under the section on integration and test.

  4. Research on MLS airborne antenna

    NASA Technical Reports Server (NTRS)

    Yu, C. L.; Burnside, W. D.

    1976-01-01

    Numerical solutions for the radiation patterns of antennas mounted on aircraft are developed. The airborne antenna problems associated with the Microwave Landing System (MLS) are emphasized. Based on the requirements of the MLS, volumetric pattern solutions are essential. Previous attempts at solving for the volumetric patterns were found to be far too complex and very inefficient. However as a result of previous efforts, it is possible to combine the elevation and roll plane pattern solutions to give the complete volumetric pattern. This combination is described as well as the aircraft simulation models used in the analysis. A numerical technique is presented to aid in the simulation of the aircraft studied. Finally, a description of the input data used in the computer code is given.

  5. Global deposition of airborne dioxin.

    PubMed

    Booth, Shawn; Hui, Joe; Alojado, Zoraida; Lam, Vicky; Cheung, William; Zeller, Dirk; Steyn, Douw; Pauly, Daniel

    2013-10-15

    We present a global dioxin model that simulates one year of atmospheric emissions, transport processes, and depositions to the earth's terrestrial and marine habitats. We map starting emission levels for each land area, and we also map the resulting deposits to terrestrial and marine environments. This model confirms that 'hot spots' of deposition are likely to be in northern Europe, eastern North America, and in parts of Asia with the highest marine dioxin depositions being the northeast and northwest Atlantic, western Pacific, northern Indian Ocean and the Mediterranean. It also reveals that approximately 40% of airborne dioxin emissions are deposited to marine environments and that many countries in Africa receive more dioxin than they produce, which results in these countries being disproportionately impacted. Since human exposure to dioxin is largely through diet, this work highlights food producing areas that receive higher atmospheric deposits of dioxin than others. PMID:23962732

  6. Airborne remote sensing of forest biomes

    NASA Technical Reports Server (NTRS)

    Sader, Steven A.

    1987-01-01

    Airborne sensor data of forest biomes obtained using an SAR, a laser profiler, an IR MSS, and a TM simulator are presented and examined. The SAR was utilized to investigate forest canopy structures in Mississippi and Costa Rica; the IR MSS measured forest canopy temperatures in Oregon and Puerto Rico; the TM simulator was employed in a tropical forest in Puerto Rico; and the laser profiler studied forest canopy characteristics in Costa Rica. The advantages and disadvantages of airborne systems are discussed. It is noted that the airborne sensors provide measurements applicable to forest monitoring programs.

  7. Anthropogenic Osmium in Airborne Particles from Woods Hole, Massachusetts, USA

    NASA Astrophysics Data System (ADS)

    Peucker-Ehrenbrink, B.; Sen, I. S.; Geboy, N.

    2012-12-01

    The global geochemical cycle of osmium has been significantly disturbed by the introduction of automobile exhaust catalysts to convert noxious gas emissions into more benign forms. Anthropogenic osmium has been reported in rainwater, snow, and in the urban airborne particles from around the world to reveal global-scale osmium pollution [1, 2]. In this study, we report on the platinum group element (PGE) concentrations and osmium isotope ratios of airborne particles (PM10) collected in Woods Hole, a small coastal town in Massachusetts to better understand inputs of anthropogenic osmium to rural environments. We further investigate the use of osmium isotopes to track sources of airborne particles and support source apportionment studies on a continental scale. The samples used in this study were collected at Woods Hole Oceanographic Institution over one year (2008-2009). From this collection twelve samples for which the backward air mass trajectories have been determined were selected for osmium isotope analyses. Our results show that the osmium and platinum concentrations are an order of magnitude lower when compared to downtown Boston [2]. The average Os, Pt and Ir concentrations are 0.006±0.012, 0.019±0.023, and 0.685±0.634 pg m-3, respectively. The 187Os/188Os of the aerosols range from 0.275 to 0.788. As continental crust is radiogenic (187Os/188Os >1) and PGE ore bodies generally have unradiogenic 187Os/188Os (~0.2), the unradiogenic 187Os/188Os signature of the aerosols indicates anthropogenic contributions. With 95% of the total osmium mobilization on land being attributed to human activities [3], it is clear that human imprint on airborne particles is not restricted to urban centers with high traffic flows, but also affects rural environments. Aerosol particles that have backward air mass trajectories from the Southwest, the densely populated and industrialized Eastern seaboard, are characterized by unradiogenic osmium, while air masses from the North

  8. Design of tracking mount and controller for mobile satellite laser ranging system

    NASA Astrophysics Data System (ADS)

    Park, Cheol Hoon; Son, Young Su; Kim, Byung In; Ham, Sang Young; Lee, Sung Whee; Lim, Hyung Chul

    2012-01-01

    In this study, we have proposed and implemented a design for the tracking mount and controller of the ARGO-M (Accurate Ranging system for Geodetic Observation - Mobile) which is a mobile satellite laser ranging (SLR) system developed by the Korea Astronomy and Space Science Institute (KASI) and Korea Institute of Machinery and Materials (KIMM). The tracking mount comprises a few core components such as bearings, driving motors and encoders. These components were selected as per the technical specifications for the tracking mount of the ARGO-M. A three-dimensional model of the tracking mount was designed. The frequency analysis of the model predicted that the first natural frequency of the designed tracking mount was high enough. The tracking controller is simulated using MATLAB/xPC Target to achieve the required pointing and tracking accuracy. In order to evaluate the system repeatability and tracking accuracy of the tracking mount, a prototype of the ARGO-M was fabricated, and repeatability tests were carried out using a laser interferometer. Tracking tests were conducted using the trajectories of low earth orbit (LEO) and high earth orbit (HEO) satellites. Based on the test results, it was confirmed that the prototype of the tracking mount and controller of the ARGO-M could achieve the required repeatability along with a tracking accuracy of less than 1 arcsec.

  9. To Track or Not to Track?

    ERIC Educational Resources Information Center

    Hesson, Heather

    2010-01-01

    Background: This paper was written for a graduate level action research course at Muskingum University, located in New Concord, OH. Purpose: The purpose of this research was to determine which method of instruction best serves ALL high school students. Is it more advantageous to track ("ability group") students or not to track students in high…

  10. Calculating track thrust with track functions

    NASA Astrophysics Data System (ADS)

    Chang, Hsi-Ming; Procura, Massimiliano; Thaler, Jesse; Waalewijn, Wouter J.

    2013-08-01

    In e+e- event shapes studies at LEP, two different measurements were sometimes performed: a “calorimetric” measurement using both charged and neutral particles and a “track-based” measurement using just charged particles. Whereas calorimetric measurements are infrared and collinear safe, and therefore calculable in perturbative QCD, track-based measurements necessarily depend on nonperturbative hadronization effects. On the other hand, track-based measurements typically have smaller experimental uncertainties. In this paper, we present the first calculation of the event shape “track thrust” and compare to measurements performed at ALEPH and DELPHI. This calculation is made possible through the recently developed formalism of track functions, which are nonperturbative objects describing how energetic partons fragment into charged hadrons. By incorporating track functions into soft-collinear effective theory, we calculate the distribution for track thrust with next-to-leading logarithmic resummation. Due to a partial cancellation between nonperturbative parameters, the distributions for calorimeter thrust and track thrust are remarkably similar, a feature also seen in LEP data.

  11. Track segment association for ground moving targets with evasive move-stop-move maneuvers

    NASA Astrophysics Data System (ADS)

    Zhang, Shuo; Bar-Shalom, Yaakov

    2010-04-01

    In a real tracking system, track breakages can occur due to highly maneuvering targets, low detection probability, or clutter. Previously, a track segment association approach (TSA) was developed for an airborne early warning (AEW) system to improve track continuity by"stitching" broken track segments pertaining to the same target. However, this technique cannot provide satisfactory association performance in tracking with a GMTI radar ground moving targets employing evasive move-stop-move maneuvers. To avoid detection by a GMTI radar, targets can deliberately stop for some time before moving again. Since a GMTI radar does not detect a target when the radial velocity (along the line-of-sight from the sensor) falls below a certain minimum detectable velocity (MDV), the move-stop-move maneuvers of the targets usually lead to broken tracks as a result. We present a new TSA technique which employs a dummy track to formulate a complete association. By using an IMM estimator with state-dependent mode transition probabilities (IMM-SDP) for track segment prediction (forward and backward), the proposed algorithm can effectively stitch both "regular" broken tracks and broken tracks due to targets' move-stop-move maneuvers. Comparisons are given to show the advantages of the proposed algorithm in broken tracks reduction and track continuity improvement.

  12. Airborne laser altimetry survey of Glaciar Tyndall, Patagonia

    NASA Astrophysics Data System (ADS)

    Keller, Kristian; Casassa, Gino; Rivera, Andrés; Forsberg, Rene; Gundestrup, Niels

    2007-10-01

    The first airborne laser altimetry measurements of a glacier in South America are presented. Data were collected in November of 2001 over Glaciar Tyndall, Torres del Paine National Park, Chilean Patagonia, onboard a Twin Otter airplane of the Chilean Air Force. A laser scanner with a rotating polygon-mirror system together with an Inertial Navigation System (INS) were fixed to the floor of the aircraft, and used in combination with two dual-frequency GPS receivers. Together, the laser-INS-GPS system had a nominal accuracy of 30 cm after data processing. On November 23rd, a total of 235 km were flown over the ablation area of Glaciar Tyndall, with 5 longitudinal tracks with a mean swath width of 300 m, which results in a point spacing of approximately 2 m both along and across track. A digital elevation model (DEM) generated using the laser altimetry data was compared with a DEM produced from a 1975 map (1:50,000 scale — Instituto Geográfico Militar (IGM), Chile). A mean thinning of - 3.1 ± 1.0 m a - 1 was calculated for the ablation area of Glaciar Tyndall, with a maximum value of - 7.7 ± 1.0 m a - 1 at the calving front at 50 m a.s.l. and minimum values of between - 1.0 and - 2.0 ± 1.0 m a - 1 at altitudes close to the equilibrium line altitude (900 m a.s.l.). The thinning rates derived from the airborne survey were similar to the results obtained by means of ground survey carried out at ˜ 600 m of altitude on Glaciar Tyndall between 1975 and 2002, yielding a mean thinning of - 3.2 m a - 1 [Raymond, C., Neumann, T.A., Rignot, E., Echelmeyer, K.A., Rivera, A., Casassa, G., 2005. Retreat of Tyndall Glacier, Patagonia, over the last half century. Journal of Glaciology 173 (51), 239-247.]. A good agreement was also found between ice elevation changes measured with laser data and previous results obtained with Shuttle Radar Topography Mission (SRTM) data. We conclude that airborne laser altimetry is an effective means for accurately detecting glacier elevation

  13. Validation of Airborne CO2 Laser Measurements

    NASA Astrophysics Data System (ADS)

    Browell, E. V.; Dobler, J. T.; Kooi, S.; Fenn, M. A.; Choi, Y.; Vay, S. A.; Harrison, F. W.; Moore, B.; Zaccheo, T. S.

    2010-12-01

    This paper discusses the flight test validation of a unique, multi-frequency, intensity-modulated, single-beam laser absorption spectrometer (LAS) that operates near 1.57 μm for remote column CO2 measurements. This laser system is under development for a future space-based mission to determine the global distribution of regional-scale CO2 sources and sinks, which is the objective of the NASA Active Sensing of CO2 Emissions during Nights, Days, and Seasons (ASCENDS) mission. A prototype of this LAS system, called the Multi-frequency Fiber Laser Lidar (MFLL), was developed by ITT, and it has been flight tested in nine airborne campaigns since May 2005. This paper focuses on the most recent results obtained over the last two years of flight-testing where the MFLL remote CO2 column measurements were evaluated against airborne in situ CO2 profile measurements traceable to World Meteorological Organization standards. A comprehensive multiple-aircraft flight test program was conducted over Oklahoma and Virginia in July-August 2009. The MFLL obtained surface reflectance and average CO2 column variations along the 50-km flight legs over the Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Central Facility (CF) in Lamont, Oklahoma; over rural Virginia and North Carolina; and over the Chesapeake Bay. For a flight altitude of 4.6 km, the average signal to noise ratio (SNR) for a 1-s CO2 column measurement was found to be 760, which is the equivalent of a CO2 mixing ratio precision of 0.60 ppmv, and for a 10-s average the SNR was found to be 2002 or 0.20 ppmv. Absolute comparisons of MFLL-derived and in situ-derived CO2 column measurements were made for all daytime flights conducted over Oklahoma and Virginia with an average agreement to within 0.32 ppmv. A major ASCENDS flight test campaign was conducted using the NASA DC-8 during 6-18 July 2010. The MFLL system and associated in situ CO2 instrumentation were operated on DC-8 flights over the Central Valley

  14. An examination of along-track interferometry for detecting ground moving targets

    NASA Technical Reports Server (NTRS)

    Chen, Curtis W.; Chapin, Elaine; Muellerschoen, Ron; Hensley, Scott

    2005-01-01

    Along-track interferometry (ATI) is an interferometric synthetic aperture radar technique primarily used to measure Earth-surface velocities. We present results from an airborne experiment demonstrating phenomenology specific to the context of observing discrete ground targets moving admidst a stationary clutter background.

  15. Indoor airborne bacterial communities are influenced by ventilation, occupancy, and outdoor air source.

    PubMed

    Meadow, J F; Altrichter, A E; Kembel, S W; Kline, J; Mhuireach, G; Moriyama, M; Northcutt, D; O'Connor, T K; Womack, A M; Brown, G Z; Green, J L; Bohannan, B J M

    2014-02-01

    Architects and engineers are beginning to consider a new dimension of indoor air: the structure and composition of airborne microbial communities. A first step in this emerging field is to understand the forces that shape the diversity of bioaerosols across space and time within the built environment. In an effort to elucidate the relative influences of three likely drivers of indoor bioaerosol diversity - variation in outdoor bioaerosols, ventilation strategy, and occupancy load - we conducted an intensive temporal study of indoor airborne bacterial communities in a high-traffic university building with a hybrid HVAC (mechanically and naturally ventilated) system. Indoor air communities closely tracked outdoor air communities, but human-associated bacterial genera were more than twice as abundant in indoor air compared with outdoor air. Ventilation had a demonstrated effect on indoor airborne bacterial community composition; changes in outdoor air communities were detected inside following a time lag associated with differing ventilation strategies relevant to modern building design. Our results indicate that both occupancy patterns and ventilation strategies are important for understanding airborne microbial community dynamics in the built environment. PMID:23621155

  16. Indoor airborne bacterial communities are influenced by ventilation, occupancy, and outdoor air source

    PubMed Central

    Meadow, J F; Altrichter, A E; Kembel, S W; Kline, J; Mhuireach, G; Moriyama, M; Northcutt, D; O'Connor, T K; Womack, A M; Brown, G Z; Green, J L ; Bohannan, B J M

    2014-01-01

    Architects and engineers are beginning to consider a new dimension of indoor air: the structure and composition of airborne microbial communities. A first step in this emerging field is to understand the forces that shape the diversity of bioaerosols across space and time within the built environment. In an effort to elucidate the relative influences of three likely drivers of indoor bioaerosol diversity – variation in outdoor bioaerosols, ventilation strategy, and occupancy load – we conducted an intensive temporal study of indoor airborne bacterial communities in a high-traffic university building with a hybrid HVAC (mechanically and naturally ventilated) system. Indoor air communities closely tracked outdoor air communities, but human-associated bacterial genera were more than twice as abundant in indoor air compared with outdoor air. Ventilation had a demonstrated effect on indoor airborne bacterial community composition; changes in outdoor air communities were detected inside following a time lag associated with differing ventilation strategies relevant to modern building design. Our results indicate that both occupancy patterns and ventilation strategies are important for understanding airborne microbial community dynamics in the built environment. PMID:23621155

  17. ESA Cryovex 2011 Airborne Campaign for CRYOSAT-2 Calibration and Validation

    NASA Astrophysics Data System (ADS)

    Skourup, H.; Einarsson, I.; Sandberg, L.; Forsberg, R.; Stenseng, L.; Hendricks, S.; Helm, V.; Davidson, M.

    2011-12-01

    After the successful launch of CryoSat-2 in April 2010, the first direct validation campaign of the satellite was carried out in the April-May 2011. DTU Space has been involved in ESA's CryoSat Validation Experiment (CryoVEx) with airborne activities since 2003. To validate the performance of the CryoSat-2 radar altimeter (SIRAL), the aircraft is equipped with an airborne version of the SIRAL altimeter (ASIRAS) together with a laser scanner. Of particular interest is to study the penetration depth of SIRAL into both land- and sea ice. This can be done by comparing the radar and laser measurements, as the laser reflects on the surface, and by overflight of laser reflectors. In the spring of 2011 the DTU Space airborne team visited five main validation sites: Devon ice cap (Canada), Austfonna ice cap (Svalbard), the EGIG line crossing the Greenland Ice Sheet, as well as the sea ice north of Alert and sea ice around Svalbard in the Fram Strait. Selected tracks were planned to match CryoSat-2 passes and a few of them were flown in formation flight with the Alfred Wegener Institute (AWI) Polar-5 carrying an EM-bird. We present an overview of the 2011 airborne campaign together with first results of the CryoSat-2 underflights.

  18. Validating Cryosat-2 elevation estimates with airborne laser scanner data for the Greenland ice sheet, Austfonna and Devon ice caps

    NASA Astrophysics Data System (ADS)

    Simonsen, Sebastian B.; Sandberg Sørensen, Louise; Nilsson, Johan; Helm, Veit; Langley, Kirsty A.; Forsberg, Rene; Hvidegaard, Sine M.; Skourup, Henriette

    2015-04-01

    The ESA CryoSat-2 satellite, launched in late 2010, carries a new type of radar altimeter especially designed for monitoring changes of sea and land ice. The radar signal might penetrate into the snow pack and the depth of the radar reflecting surface depends on the ratio between the surface and the volume backscatter, which is a function of several different properties such as snow density, crystal structure and surface roughness. In case of large volume scatter, the radar waveforms become broad and the determination of the range (surface elevation) becomes more difficult. Different algorithms (retrackers) are used for the range determination, and estimated surface penetration is highly dependent on the applied retracker. As part of the ESA-CryoVEx/CryoVal-Land Ice projects, DTU Space has gathered accurate airborne laser scanner elevation measurements. Sites on the Greenland ice sheet, Austfonna and Devon ice caps, has been surveyed repeatedly, aligned with Cryosat-2 ground tracks and surface experiments. Here, we utilize elevation estimates from available Cryosat-2 retrackers (ESA level-2 retracker, DTU retracker, etc.) and validate the elevation measurements against ESA-CryoVEx campaigns. A difference between laser and radar elevations is expected due to radar penetration issues, however an inter-comparison between retrackers will shed light on individual performances and biases. Additionally, the geo-location of the radar return will also be a determining factor for the precision. Ultimately, the use of multiple retrackers can provide information about subsurface conditions and utilize more of the waveform information than presently used in radar altimetry.

  19. Limitations on quantum key repeaters.

    PubMed

    Bäuml, Stefan; Christandl, Matthias; Horodecki, Karol; Winter, Andreas

    2015-01-01

    A major application of quantum communication is the distribution of entangled particles for use in quantum key distribution. Owing to noise in the communication line, quantum key distribution is, in practice, limited to a distance of a few hundred kilometres, and can only be extended to longer distances by use of a quantum repeater, a device that performs entanglement distillation and quantum teleportation. The existence of noisy entangled states that are undistillable but nevertheless useful for quantum key distribution raises the question of the feasibility of a quantum key repeater, which would work beyond the limits of entanglement distillation, hence possibly tolerating higher noise levels than existing protocols. Here we exhibit fundamental limits on such a device in the form of bounds on the rate at which it may extract secure key. As a consequence, we give examples of states suitable for quantum key distribution but unsuitable for the most general quantum key repeater protocol. PMID:25903096

  20. TOPEX orbit determination and gravity recovery using Global Positioning System data from repeat orbits

    NASA Technical Reports Server (NTRS)

    Wu, Jiun-Tsong; Yunck, Thomas P.

    1992-01-01

    A covariance analysis is presented for satellite tracking and gravity recovery with a differential Global Positioning System-based technique to be demonstrated on TOPEX in the early 1990s. The technique employs data from an ensemble of repeat ground tracks to recover a unique satellite epoch state for each track and a set of invariant positional parameters common to all tracks. The positional parameters represent the effect of mismodeled gravitational field on the satellite orbit. At an altitude of 1336 km, where gravity modeling is the dominant systematic error, averaging of random error over many arcs and adjustment of the gravity model reduce the final satellite position error. The positional parameters can then be used to produce a refined global gravity model. The analysis indicates that errors ranging from 5 to 8 cm in TOPEX altitude and 0.05 to 0.2 mGal for the gravity field can be achieved, depending on the number of repeat arcs used.

  1. Topex orbit determination and gravity recovery using GPS data from repeat orbits

    NASA Technical Reports Server (NTRS)

    Wu, Jiun-Tsong; Yunck, Thomas P.

    1988-01-01

    A covariance analysis is presented for a differential GPS-based technique for satellite tracking and gravity recovery to be demonstrated on Topex in the early 1990's. The technique employs data from an ensemble of repeat ground tracks to recover a unique satellite epoch state for each track and a set of invariant local gravity parameters common to all tracks. For satellites above about 800 km altitude, where gravity modeling is the dominant systematic error, averaging of random error over many arcs and adjustment of the gravity model reduces the final satellite position error. The local gravity parameters can then be used to produce a refined global gravity model. The analysis indicates that errors ranging from 5 to 8 cm in Topex altitude and 0.05 to 0.2 mgal for the gravity field can be achieved, depending on the number of repeat arcs used.

  2. Airborne Gamma-Spectrometry in Switzerland

    SciTech Connect

    Butterweck, Gernot; Bucher, Benno; Rybach, Ladislaus

    2008-08-07

    Airborne gamma-spectrometry is able to obtain fast radiological information over large areas. The airborne gamma-spectrometry unit deployed in Switzerland by the Swiss National Emergency Operations Centre (NEOC) consists of a Swiss army Super Puma helicopter equipped with four NaI-Detectors with a total volume of 17 liters, associated electronics and a real-time data evaluation and mapping unit developed by the Swiss Federal Institute of Technology (ETH) and the Paul Scherrer Institut (PSI). The operational readiness of the airborne gamma-spectrometry system is validated in annual exercises of one week duration. Data from 2005 and 2006 exercises are represented in maps of {sup 137}Cs activity concentration for two towns located in southern and western Switzerland. An indicator of man-made radioactivity (MMGC ratio) is demonstrated for an area with four different types of nuclear installations. The intercomparison between airborne gamma-spectrometry and ground measurements showed good agreement between both methods.

  3. Principles for Sampling Airborne Radioactivity from Stacks

    SciTech Connect

    Glissmeyer, John A.

    2010-10-18

    This book chapter describes the special processes involved in sampling the airborne effluents from nuclear faciities. The title of the book is Radioactive Air Sampling Methods. The abstract for this chapter was cleared as PNNL-SA-45941.

  4. SOURCES OF HUMAN EXPOSURE TO AIRBORNE PAH

    EPA Science Inventory

    Personal exposures to airborne particulate polycyclic aromatic hydrocarbons (PAHs) were studied in several populations in the US, Japan, and Czech Republic. Personal exposure monitors, developed for human exposure biomonitoring studies were used to collect fine particles (<_ 1....

  5. Hysteresis of magnetostructural transitions: Repeatable and non-repeatable processes

    NASA Astrophysics Data System (ADS)

    Provenzano, Virgil; Della Torre, Edward; Bennett, Lawrence H.; ElBidweihy, Hatem

    2014-02-01

    The Gd5Ge2Si2 alloy and the off-stoichiometric Ni50Mn35In15 Heusler alloy belong to a special class of metallic materials that exhibit first-order magnetostructural transitions near room temperature. The magnetic properties of this class of materials have been extensively studied due to their interesting magnetic behavior and their potential for a number of technological applications such as refrigerants for near-room-temperature magnetic refrigeration. The thermally driven first-order transitions in these materials can be field-induced in the reverse order by applying a strong enough field. The field-induced transitions are typically accompanied by the presence of large magnetic hysteresis, the characteristics of which are a complicated function of temperature, field, and magneto-thermal history. In this study we show that the virgin curve, the major loop, and sequentially measured MH loops are the results of both repeatable and non-repeatable processes, in which the starting magnetostructural state, prior to the cycling of field, plays a major role. Using the Gd5Ge2Si2 and Ni50Mn35In15 alloys, as model materials, we show that a starting single phase state results in fully repeatable processes and large magnetic hysteresis, whereas a mixed phase starting state results in non-repeatable processes and smaller hysteresis.

  6. Color image processing and object tracking workstation

    NASA Technical Reports Server (NTRS)

    Klimek, Robert B.; Paulick, Michael J.

    1992-01-01

    A system is described for automatic and semiautomatic tracking of objects on film or video tape which was developed to meet the needs of the microgravity combustion and fluid science experiments at NASA Lewis. The system consists of individual hardware parts working under computer control to achieve a high degree of automation. The most important hardware parts include 16 mm film projector, a lens system, a video camera, an S-VHS tapedeck, a frame grabber, and some storage and output devices. Both the projector and tapedeck have a computer interface enabling remote control. Tracking software was developed to control the overall operation. In the automatic mode, the main tracking program controls the projector or the tapedeck frame incrementation, grabs a frame, processes it, locates the edge of the objects being tracked, and stores the coordinates in a file. This process is performed repeatedly until the last frame is reached. Three representative applications are described. These applications represent typical uses and include tracking the propagation of a flame front, tracking the movement of a liquid-gas interface with extremely poor visibility, and characterizing a diffusion flame according to color and shape.

  7. Laser-jamming effectiveness analysis of combined-fiber lasers for airborne defense systems.

    PubMed

    Jie, Xu; Shanghong, Zhao; Rui, Hou; Shengbao, Zhan; Lei, Shi; Jili, Wu; Shaoqiang, Fang; Yongjun, Li

    2008-12-20

    The laser-jamming effectiveness of combined fiber lasers for airborne defense systems is analyzed in detail. Our preliminary experimental results are proof of the concept of getting a high-power laser through a beam combination technique. Based on combined fiber lasers, the jamming effectiveness of four-quadrant guidance and imaging guidance systems are evaluated. The simulation results have proved that for a four-quadrant guidance system, the tracking system takes only two seconds to complete tracking, and the new tracking target is the jamming laser; for the imaging guidance system, increasing the power of the jamming laser or the distance between the target and the jamming laser are both efficient ways to achieve a successful laser jamming. PMID:19104536

  8. Repeating seismic events in China.

    PubMed

    Schaff, David P; Richards, Paul G

    2004-02-20

    About 10% of seismic events in and near China from 1985 to 2000 were repeating events not more than about 1 kilometer from each other. We cross-correlated seismograms from approximately 14,000 earthquakes and explosions and measured relative arrival times to approximately 0.01 second, enabling lateral location precision of about 100 to 300 meters. Such precision is important for seismic hazard studies, earthquake physics, and nuclear test ban verification. Recognition and measurement of repeating signals in archived data and the resulting improvement in location specificity quantifies the inaccuracy of current procedures for picking onset times and locating events. PMID:14976310

  9. Mapping of airborne Doppler radar data

    SciTech Connect

    Lee, W.; Dodge, P.; Marks, F.D. Jr.; Hildebrand, P.H. NOAA, Miami, FL )

    1994-04-01

    Two sets of equations are derived to (1) map airborne Doppler radar data from an aircraft-relative coordinate system to an earth-relative coordinate system, and (2) remove the platform motion from the observed Doppler velocities. These equations can be applied to data collected by the National Oceanic and Atmospheric Administration WP-3D system, the National Center for Atmospheric Research Electra Doppler Radar (ELDORA) system, and other airborne radar systems.

  10. Hybrid multitarget tracking system

    NASA Astrophysics Data System (ADS)

    Subramanian, Aswinikumar; Hassebrook, Laurence G.; Ghosal, Sugata; Kim, Michael

    1992-11-01

    A common function for human being is to detect the movement of an object against a stationary background and then to lock on to and trace its motion. This natural process becomes very tedious in industrial or military environments where the database of images to be searched is huge or where the function is to be repeated continuously. Thus automation can assist people carrying out such tasks. This is the case in security systems, military reconnaissance, military targeting, aircraft tracking, assembly line manufacturing systems, and quality control. We present a hybrid system to do such tasks. The technique is simulated on computer using numerical algorithms and is successful under many situations. For implementation an ideal system using optical components is presented. This hybrid system employs three main subsystems which are combined in such a way as to compensate for each other's drawbacks yet enhance each other's virtues. The first system is a velocity correlation system which correlates two adjacent frames in a sequence of image frames. The resultant velocity correlations are searched to find the potential velocity profiles at which an object may be moving. These velocity profiles are then processed by the multi-frame mean subsystem which performs a geometric (or arithmetic mean) operation on the image frames. These frames are displaced by the selected velocity profiles and thereby aligning the object in the given frames for detection. Algorithms have been developed and tested to perform this technique on selected databases. Also algorithms to synthesize test images have been developed and the results are presented.

  11. Pure laparoscopic hepatectomy as repeat surgery and repeat hepatectomy

    PubMed Central

    Isetani, Masashi; Morise, Zenichi; Kawabe, Norihiko; Tomishige, Hirokazu; Nagata, Hidetoshi; Kawase, Jin; Arakawa, Satoshi

    2015-01-01

    AIM: To assess clinical outcomes of laparoscopic hepatectomy (LH) in patients with a history of upper abdominal surgery and repeat hepatectomy. METHODS: This study compared the perioperative courses of patients receiving LH at our institution that had or had not previously undergone upper abdominal surgery. Of the 80 patients who underwent LH, 22 had prior abdominal surgeries, including hepatectomy (n = 12), pancreatectomy (n = 3), cholecystectomy and common bile duct excision (n = 1), splenectomy (n = 1), total gastrectomy (n = 1), colectomy with the involvement of transverse colon (n = 3), and extended hysterectomy with extensive lymph-node dissection up to the upper abdomen (n = 1). Clinical indicators including operating time, blood loss, hospital stay, and morbidity were compared among the groups. RESULTS: Eighteen of the 22 patients who had undergone previous surgery had severe adhesions in the area around the liver. However, there were no conversions to laparotomy in this group. In the 58 patients without a history of upper abdominal surgery, the median operative time was 301 min and blood loss was 150 mL. In patients with upper abdominal surgical history or repeat hepatectomy, the operative times were 351 and 301 min, and blood loss was 100 and 50 mL, respectively. The median postoperative stay was 17, 13 and 12 d for patients with no history of upper abdominal surgery, patients with a history, and patients with repeat hepatectomy, respectively. There were five cases with complications in the group with no surgical history, compared to only one case in the group with a prior history. There were no statistically significant differences in the perioperative results between the groups with and without upper abdominal surgical history, or with repeat hepatectomy. CONCLUSION: LH is feasible and safe in patients with a history of upper abdominal surgery or repeat hepatectomy. PMID:25624731

  12. Airborne Laser Mapping of Greenland

    SciTech Connect

    Krabill, W.B.; Thomas, R.H.; Martin, C.F.; Sonntag, J.G.

    1996-10-01

    The Polar ice sheets contain enough water to raise Earth`s sea level by some 70 m. It is not clear whether changes in these ice sheets are contributing to the current rise. Ice sheet mass balance estimates can be obtained by monitoring the topography of selected Polar regions. The Arctic Ice Mapping (AIM) Project is a continuing program designed to provide a record of the absolute height of representative Arctic ice sheets. Using the Global Positioning System (GPS), aircraft flight lines may be duplicated with sufficient tolerance to provide repeated laser elevation measurements from one year to another. The raw GPS measurements are re-processed post-mission to provide sub-10 cm trajectories for each aircraft flight. This program began in 1991 with a proof-of-concept mission to Greenland. The data from this mission demonstrates 20 cm repeatability, principally due to the limited GPS constellation available. Refinements in all phases of the program (software, law and GPS hardware, and a complete GPS constellation) have yielded 10 cm repeatability in data from subsequent years, which includes probable geophysical change in the surface due to storm events and wind drift. 5 refs., 5 figs., 2 tabs.

  13. Photographing Track Meets.

    ERIC Educational Resources Information Center

    Palmer, Erik

    2001-01-01

    Argues that the sport of track and field, because of the sport itself and its relatively easy access to photographers, is an obvious target for cameras. Discusses rules of the track that photographers must follow; picking a location; and equipment. Discusses shooting four specific track and field events and offers behind the scenes photos. (SR)

  14. Solar tracking apparatus

    DOEpatents

    Hammons, Burrell E.

    1980-01-01

    The invention relates to a solar tracking device which tracks the position of the sun using paired, partially-shaded photocells. Auxiliary photocells are used for initial acquisition of the sun and for the suppression of false tracking when the sun is obscured by clouds.

  15. Solar tracking apparatus

    DOEpatents

    Hammons, B.E.

    The invention relates to a solar tracking device which tracks the position of the sun using paired, partially-shaded photocells. Auxilliary photocells are used for initial acquisition of the sun and for the suppression of false tracking when the sun is obscured by clouds.

  16. Track and Field Facilities.

    ERIC Educational Resources Information Center

    Wood, Tony

    2001-01-01

    Discusses planning and design tips that help ensure track and field facilities are successful and well-suited to both school and community use. Examines approaches to determining the best track surface and ways to maximize track and field flexibility with limited space. (GR)

  17. Challenges and opportunities of airborne metagenomics.

    PubMed

    Behzad, Hayedeh; Gojobori, Takashi; Mineta, Katsuhiko

    2015-05-01

    Recent metagenomic studies of environments, such as marine and soil, have significantly enhanced our understanding of the diverse microbial communities living in these habitats and their essential roles in sustaining vast ecosystems. The increase in the number of publications related to soil and marine metagenomics is in sharp contrast to those of air, yet airborne microbes are thought to have significant impacts on many aspects of our lives from their potential roles in atmospheric events such as cloud formation, precipitation, and atmospheric chemistry to their major impact on human health. In this review, we will discuss the current progress in airborne metagenomics, with a special focus on exploring the challenges and opportunities of undertaking such studies. The main challenges of conducting metagenomic studies of airborne microbes are as follows: 1) Low density of microorganisms in the air, 2) efficient retrieval of microorganisms from the air, 3) variability in airborne microbial community composition, 4) the lack of standardized protocols and methodologies, and 5) DNA sequencing and bioinformatics-related challenges. Overcoming these challenges could provide the groundwork for comprehensive analysis of airborne microbes and their potential impact on the atmosphere, global climate, and our health. Metagenomic studies offer a unique opportunity to examine viral and bacterial diversity in the air and monitor their spread locally or across the globe, including threats from pathogenic microorganisms. Airborne metagenomic studies could also lead to discoveries of novel genes and metabolic pathways relevant to meteorological and industrial applications, environmental bioremediation, and biogeochemical cycles. PMID:25953766

  18. Challenges and Opportunities of Airborne Metagenomics

    PubMed Central

    Behzad, Hayedeh; Gojobori, Takashi; Mineta, Katsuhiko

    2015-01-01

    Recent metagenomic studies of environments, such as marine and soil, have significantly enhanced our understanding of the diverse microbial communities living in these habitats and their essential roles in sustaining vast ecosystems. The increase in the number of publications related to soil and marine metagenomics is in sharp contrast to those of air, yet airborne microbes are thought to have significant impacts on many aspects of our lives from their potential roles in atmospheric events such as cloud formation, precipitation, and atmospheric chemistry to their major impact on human health. In this review, we will discuss the current progress in airborne metagenomics, with a special focus on exploring the challenges and opportunities of undertaking such studies. The main challenges of conducting metagenomic studies of airborne microbes are as follows: 1) Low density of microorganisms in the air, 2) efficient retrieval of microorganisms from the air, 3) variability in airborne microbial community composition, 4) the lack of standardized protocols and methodologies, and 5) DNA sequencing and bioinformatics-related challenges. Overcoming these challenges could provide the groundwork for comprehensive analysis of airborne microbes and their potential impact on the atmosphere, global climate, and our health. Metagenomic studies offer a unique opportunity to examine viral and bacterial diversity in the air and monitor their spread locally or across the globe, including threats from pathogenic microorganisms. Airborne metagenomic studies could also lead to discoveries of novel genes and metabolic pathways relevant to meteorological and industrial applications, environmental bioremediation, and biogeochemical cycles. PMID:25953766

  19. Forest stand structure from airborne polarimetric InSAR

    NASA Astrophysics Data System (ADS)

    Balzter, H.; Saich, P.; Luckman, A. J.; Skinner, L.; Grant, J.

    2002-01-01

    Interferometric SAR at short wavelengths can be used to retrieve stand height of forests. We evaluate the precision of tree height estimation from airborne single-pass interferometric E-SAR data at X-band VV polarisation and repeat-pass L-band polarimetric data. General yield class curves were used to estimate tree height from planting year, tree species and yield class data provided by the Forest Enterprise. The data were compared to tree height estimates from X-VV single-pass InSAR and repeat-pass polarimetric InSAR at L-band acquired by DLR's E-SAR during the SHAC campaign 2000. The effect of gap structure and incidence angle on retrieval precision of tree height from interferometric SAR is analysed. Appropriate correction methods to improve tree height retrieval are proposed. The coherent microwave model CASM is used with a Lindenmayer system tree model to simulate the observed underestimation of stand height in the presence of gaps.

  20. Finite resolution multitarget tracking

    NASA Astrophysics Data System (ADS)

    Mušicki, Darko; Morelande, Mark R.

    2005-09-01

    Target tracking algorithms have to operate in an environment of uncertain measurement origin, due to the presence of randomly detected target measurements as well as clutter measurements from unwanted random scatterers. A majority of Bayesian multi-target tracking algorithms suffer from computational complexity which is exponential in the number of tracks and the number of shared measurements. The Linear Multi-target (LM) tracking procedure is a Bayesian multi-target tracking approximation with complexity which is linear in the number of tracks and the number of shared measurements. It also has a much simpler structure than the "optimal" Bayesian multi-target tracking, with apparently negligible decrease in performance. A vast majority of target tracking algorithms have been developed with the assumption of infinite sensor resolution, where a measurement can have only one source. This assumption is not valid for real sensors, such as radars. This paper presents a multi-target tracking algorithm which removes this restriction. The procedure utilizes a simple structure of LM tracking procedure to obtain a LM Finite Resolution (LMfr) tracking procedure which is much simpler than the previously published efforts. Instead of calculating the probability of measurement merging for each combination of potentially merging targets, we evaluate only one merging hypotheses for each measurement and each track. A simulation study is presented which compares LMfr-IPDA with LM-IPDA and IPDA target tracking in a cluttered environment utilizing a finite resolution sensor with five crossing targets. The study concentrates on the false track discrimination performance and the track retention capabilities.

  1. Do Twelfths Terminate or Repeat?

    ERIC Educational Resources Information Center

    Ambrose, Rebecca; Burnison, Erica

    2015-01-01

    When finding the decimal equivalent of a fraction with 12 in the denominator, will it terminate or repeat? This question came from a seventh grader in author Erica Burnison's class as the student was pondering a poster generated by one of her classmates. Not only was the question intriguing, but it also affirmed the belief in the power of…

  2. Pentapeptide Repeat Proteins and Cyanobacteria

    SciTech Connect

    Buchko, Garry W.

    2009-10-16

    Cyanobacteria are unique in many ways and one unusual feature is the presence of a suite of proteins that contain at least one domain with a minimum of eight tandem repeated five-residues (Rfr) of the general consensus sequence A[N/D]LXX. The function of such pentapeptide repeat proteins (PRPs) are still unknown, however, their prevalence in cyanobacteria suggests that they may play some role in the unique biological activities of cyanobacteria. As part of an inter-disciplinary Membrane Biology Grand Challenge at the Environmental Molecular Sciences Laboratory (Pacific Northwest National Laboratory) and Washington University in St. Louis, the genome of Cyanothece 51142 was sequenced and its molecular biology studied with relation to circadian rhythms. The genome of Cyanothece encodes for 35 proteins that contain at least one PRP domain. These proteins range in size from 105 (Cce_3102) to 930 (Cce_2929) kDa with the PRP domains ranging in predicted size from 12 (Cce_1545) to 62 (cce_3979) tandem pentapeptide repeats. Transcriptomic studies with 29 out of the 35 genes showed that at least three of the PRPs in Cyanothece 51142 (cce_0029, cce_3083, and cce_3272) oscillated with repeated periods of light and dark, further supporting a biological function for PRPs. Using X-ray diffraction crystallography, the structure for two pentapeptide repeat proteins from Cyanothece 51142 were determined, cce_1272 (aka Rfr32) and cce_4529 (aka Rfr23). Analysis of their molecular structures suggests that all PRP may share the same structural motif, a novel type of right-handed quadrilateral β-helix, or Rfr-fold, reminiscent of a square tower with four distinct faces. Each pentapeptide repeat occupies one face of the Rfr-fold with four consecutive pentapeptide repeats completing a coil that, in turn, stack upon each other to form “protein skyscrapers”. Details of the structural features of the Rfr-fold are reviewed here together with a discussion for the possible role of end

  3. Blind phase calibration for along-track interferometry: application to Gotcha data set

    NASA Astrophysics Data System (ADS)

    Uysal, Faruk; Murthy, Vinay; Scarborough, Steven M.

    2014-06-01

    Along-Track Interferometry (ATI) has been widely used for ground moving target indication (GMTI) in airborne synthetic aperture radar (SAR) systems. In ideal cases, the ATI phase obtained using two phase centers that are aligned in the along-track dimension yield clutter-only pixels with zero phase. However, the platform's motion may create a cross-track displacement between the two phase centers and in turn offset the phase centers' baseline from the along track dimension. This cross-track offset leads to non-zero phase for clutter-only pixels, necessitating calibration for accurate GMTI. This paper proposes a blind calibration method to correct the along-track baseline error in ATI-SAR systems. The success of the proposed method is shown on a set of measured data from the Gotcha sensor.

  4. Pulsed Doppler lidar airborne scanner

    NASA Technical Reports Server (NTRS)

    Dimarzio, C. A.; Mcvicker, D. B.; Morrow, C. E.; Negus, C. C.

    1985-01-01

    This report covers the work accomplished during the reporting period on Pulsed Doppler Lidar Airborne Scanner and describes plans for the next reporting period. The objectives during the current phase of the contract are divided into four phases. Phase 1 includes ground testing of the system and analysis of data from the 1981 Severe Storms Test Flights. Phase 2 consists of preflight preparation and planning for the 1983 flight series. The flight test itself will be performed during Phase 3, and Phase 4 consists of post-flight analysis and operation of the system after that flight test. The range profile from five samples taken during Flight 10, around 1700 Z is given. The lowest curve is taken from data collected upwind of Mt. Shasta at about 10,000 feet of altitude, in a clear atmosphere, where no signals were observed. It thus is a good representation of the noise level as a function of range. The next curve was taken downwind of the mountain, and shows evidence of atmospheric returns. There is some question as to whether the data are valid at all ranges, or some ranges are contaminated by the others.

  5. Pulsed Doppler lidar airborne scanner

    NASA Astrophysics Data System (ADS)

    Dimarzio, C. A.; McVicker, D. B.; Morrow, C. E.; Negus, C. C.

    1985-10-01

    This report covers the work accomplished during the reporting period on Pulsed Doppler Lidar Airborne Scanner and describes plans for the next reporting period. The objectives during the current phase of the contract are divided into four phases. Phase 1 includes ground testing of the system and analysis of data from the 1981 Severe Storms Test Flights. Phase 2 consists of preflight preparation and planning for the 1983 flight series. The flight test itself will be performed during Phase 3, and Phase 4 consists of post-flight analysis and operation of the system after that flight test. The range profile from five samples taken during Flight 10, around 1700 Z is given. The lowest curve is taken from data collected upwind of Mt. Shasta at about 10,000 feet of altitude, in a clear atmosphere, where no signals were observed. It thus is a good representation of the noise level as a function of range. The next curve was taken downwind of the mountain, and shows evidence of atmospheric returns. There is some question as to whether the data are valid at all ranges, or some ranges are contaminated by the others.

  6. Performance Basis for Airborne Separation

    NASA Technical Reports Server (NTRS)

    Wing, David J.

    2008-01-01

    Emerging applications of Airborne Separation Assistance System (ASAS) technologies make possible new and powerful methods in Air Traffic Management (ATM) that may significantly improve the system-level performance of operations in the future ATM system. These applications typically involve the aircraft managing certain components of its Four Dimensional (4D) trajectory within the degrees of freedom defined by a set of operational constraints negotiated with the Air Navigation Service Provider. It is hypothesized that reliable individual performance by many aircraft will translate into higher total system-level performance. To actually realize this improvement, the new capabilities must be attracted to high demand and complexity regions where high ATM performance is critical. Operational approval for use in such environments will require participating aircraft to be certified to rigorous and appropriate performance standards. Currently, no formal basis exists for defining these standards. This paper provides a context for defining the performance basis for 4D-ASAS operations. The trajectory constraints to be met by the aircraft are defined, categorized, and assessed for performance requirements. A proposed extension of the existing Required Navigation Performance (RNP) construct into a dynamic standard (Dynamic RNP) is outlined. Sample data is presented from an ongoing high-fidelity batch simulation series that is characterizing the performance of an advanced 4D-ASAS application. Data of this type will contribute to the evaluation and validation of the proposed performance basis.

  7. Medicinal smoke reduces airborne bacteria.

    PubMed

    Nautiyal, Chandra Shekhar; Chauhan, Puneet Singh; Nene, Yeshwant Laxman

    2007-12-01

    This study represents a comprehensive analysis and scientific validation of our ancient knowledge about the effect of ethnopharmacological aspects of natural products' smoke for therapy and health care on airborne bacterial composition and dynamics, using the Biolog microplate panels and Microlog database. We have observed that 1h treatment of medicinal smoke emanated by burning wood and a mixture of odoriferous and medicinal herbs (havan sámagri=material used in oblation to fire all over India), on aerial bacterial population caused over 94% reduction of bacterial counts by 60 min and the ability of the smoke to purify or disinfect the air and to make the environment cleaner was maintained up to 24h in the closed room. Absence of pathogenic bacteria Corynebacterium urealyticum, Curtobacterium flaccumfaciens, Enterobacter aerogenes (Klebsiella mobilis), Kocuria rosea, Pseudomonas syringae pv. persicae, Staphylococcus lentus, and Xanthomonas campestris pv. tardicrescens in the open room even after 30 days is indicative of the bactericidal potential of the medicinal smoke treatment. We have demonstrated that using medicinal smoke it is possible to completely eliminate diverse plant and human pathogenic bacteria of the air within confined space. PMID:17913417

  8. Visualizing Airborne and Satellite Imagery

    NASA Technical Reports Server (NTRS)

    Bierwirth, Victoria A.

    2011-01-01

    Remote sensing is a process able to provide information about Earth to better understand Earth's processes and assist in monitoring Earth's resources. The Cloud Absorption Radiometer (CAR) is one remote sensing instrument dedicated to the cause of collecting data on anthropogenic influences on Earth as well as assisting scientists in understanding land-surface and atmospheric interactions. Landsat is a satellite program dedicated to collecting repetitive coverage of the continental Earth surfaces in seven regions of the electromagnetic spectrum. Combining these two aircraft and satellite remote sensing instruments will provide a detailed and comprehensive data collection able to provide influential information and improve predictions of changes in the future. This project acquired, interpreted, and created composite images from satellite data acquired from Landsat 4-5 Thematic Mapper (TM) and Landsat 7 Enhanced Thematic Mapper plus (ETM+). Landsat images were processed for areas covered by CAR during the Arctic Research of the Composition of the Troposphere from Aircraft and Satellites (ARCT AS), Cloud and Land Surface Interaction Campaign (CLASIC), Intercontinental Chemical Transport Experiment-Phase B (INTEXB), and Southern African Regional Science Initiative (SAFARI) 2000 missions. The acquisition of Landsat data will provide supplemental information to assist in visualizing and interpreting airborne and satellite imagery.

  9. Downsizing of Georgia Tech's Airborne Fluorescence Spectrometer (AFS) for the Measurement of Nitrogen Oxides

    NASA Technical Reports Server (NTRS)

    Sandholm, Scott

    1998-01-01

    This report addresses the Tropospheric Trace Gas and Airborne Measurements (TTGAMG) endeavors to further downsize and stabilize the Georgia Institute of Technology's Airborne Laser Induced Fluorescence Experiment (GITALIFE). It will mainly address the TTGAMG successes and failures as participants in the summer 1998 Wallops Island test flights on board the P3-B. Due to the restructuring and reorganization of the TTGAMG since the original funding of this grant, some of the objectives and time lines of the deliverables have been changed. Most of these changes have been covered in the preceding annual report. We are anticipating getting back on track with the original proposal's downsizing effort this summer, culminating in the GITALIFE no longer occupying a high bay rack and the loss of several hundred pounds.

  10. Grounded electrical-source airborne transient electromagnetics (GREATEM) survey of Aso Volcano, Japan

    NASA Astrophysics Data System (ADS)

    Ito, Hisatoshi; Kaieda, Hideshi; Mogi, Toru; Jomori, Akira; Yuuki, Youichi

    2014-05-01

    Grounded electrical-source airborne transient electromagnetics (GREATEM), a type of semi-airborne electromagnetics, was used to examine Aso Volcano in south-west Japan, to verify its applicability to surveying deep subsurface resistivity structures. Comparison of the GREATEM resistivity values with those of ground-based transient electromagnetics (TEM) data, repeated GREATEM survey results at the same and different flight heights, and lithologic descriptions indicated that GREATEM can successfully identify underground structures as deep as ~800 m in rugged mountainous areas. An active volcanic region (Naka-Dake crater) was mapped as a low-resistivity zone from the surface to a depth of 100 m. This low-resistivity zone extended to the west-north-west, implying future volcanic activity in this area. Therefore, the GREATEM method is useful for surveying deep structures in large, inaccessible areas, such as volcanic provinces, in a quick, cost-effective way.

  11. Expectation maximization applied to GMTI convoy tracking

    NASA Astrophysics Data System (ADS)

    Koch, Wolfgang

    2002-08-01

    Collectively moving ground targets are typical of a military ground situation and have to be treated as separate aggregated entities. For a long-range ground surveillance application with airborne GMTI radar we inparticular address the task of track maintenance for ground moving convoys consisting of a small number of individual vehicles. In the proposed approach the identity of the individual vehicles within the convoy is no longer stressed. Their kinematical state vectors are rather treated as internal degrees of freedom characterizing the convoy, which is considered as a collective unit. In this context, the Expectation Maximization technique (EM), originally developed for incomplete data problems in statistical inference and first applied to tracking applications by STREIT et al. seems to be a promising approach. We suggest to embed the EM algorithm into a more traditional Bayesian tracking framework for dealing with false or unwanted sensor returns. The proposed distinction between external and internal data association conflicts (i.e. those among the convoy vehicles) should also enable the application of sequential track extraction techniques introduced by Van Keuk for aircraft formations, providing estimates of the number of the individual convoy vehicles involved. Even with sophisticated signal processing methods (STAP: Space-Time Adaptive Processing), ground moving vehicles can well be masked by the sensor specific clutter notch (Doppler blinding). This physical phenomenon results in interfering fading effects, which can well last over a longer series of sensor updates and therefore will seriously affect the track quality unless properly handled. Moreover, for ground moving convoys the phenomenon of Doppler blindness often superposes the effects induced by the finite resolution capability of the sensor. In many practical cases a separate modeling of resolution phenomena for convoy targets can therefore be omitted, provided the GMTI detection model is used

  12. Object tracking with stereo vision

    NASA Technical Reports Server (NTRS)

    Huber, Eric

    1994-01-01

    A real-time active stereo vision system incorporating gaze control and task directed vision is described. Emphasis is placed on object tracking and object size and shape determination. Techniques include motion-centroid tracking, depth tracking, and contour tracking.

  13. Vehicle track loading simulation

    NASA Astrophysics Data System (ADS)

    Chalupa, Milan; Severa, Libor; Vlach, Radek

    2011-12-01

    The paper describes possible design of the vehicle track computational model and basic testing procedure of the track dynamic loading simulation. The proposed approach leads to an improvement of track vehicle course stability. The computational model is built for MSC. ADAMS, AVT computational simulating system. Model, which is intended for MSC computational system, is built from two basic parts. The first one is represented by geometrical part, while the second one by contact computational part of the model. The aim of the simulating calculation consist in determination of change influence of specific vehicle track constructive parameters on changes of examined qualities of the vehicle track link and changes of track vehicle course stability. The work quantifies the influence of changes of track preloading values on the demanded torque changes of driving sprocket. Further research possibilities and potential are also presented.

  14. Automatic target tracking in FLIR image sequences

    NASA Astrophysics Data System (ADS)

    Bal, Abdullah; Alam, Mohammad S.

    2004-09-01

    Moving target tracking is a challenging task and is increasingly becoming important for various applications. In this paper, we have presented target detection and tracking algorithm based on target intensity feature relative to surrounding background, and shape information of target. Proposed automatic target tracking algorithm includes two techniques: intensity variation function (IVF) and template modeling (TM). The intensity variation function is formulated by using target intensity feature while template modeling is based on target shape information. The IVF technique produces the maximum peak value whereas the reference target intensity variation is similar to the candidate target intensity variation. When IVF technique fails, due to background clutter, non-target object or other artifacts, the second technique, template modeling, is triggered by control module. By evaluating the outputs from the IVF and TM techniques, the tracker determines the real coordinates of the target. Performance of the proposed ATT is tested using real life forward-looking infrared (FLIR) image sequences taken from an airborne, moving platform.

  15. Signal analysis and radioholographic methods for airborne radio occultations

    NASA Astrophysics Data System (ADS)

    Wang, Kuo-Nung

    Global Positioning System (GPS) radio occultation (RO) is an atmospheric sounding technique utilizing the change in propagation direction and delay of the GPS signal to measure refractivity, which provides information on temperature and humidity. The GPS-RO technique is now operational on several Low Earth Orbiting (LEO) satellite missions. Nevertheless, when observing localized transient events, such as tropical storms, current LEO satellite systems cannot provide sufficiently high temporal and spatial resolution soundings. An airborne RO (ARO) system has therefore been developed for localized GPS-RO campaigns. The open-loop (OL) tracking in post-processing is used to cross-correlates the received Global Navigation Satellite System (GNSS) signal with an internally generated local carrier signal predicted from a Doppler model and extract the atmospheric refractivity information. OL tracking also allows robust processing of rising GPS signals using backward tracking, which will double the observed occultation event numbers. RO signals in the lower troposphere are adversely affected by rapid phase accelerations and severe signal power fading, however. The negative bias caused by low signal-to-noise ratio (SNR) and multipath ray propagation limits the depth of tracking in the atmosphere. Therefore, we developed a model relating the SNR to the variance in the residual phase of the observed signal produced from OL tracking, and its applicability to airborne data is demonstrated. We then apply this model to set a threshold on refractivity retrieval, based upon the cumulative unwrapping error bias, to determine the altitude limit for reliable signal tracking. To enhance the SNR and decrease the unwrapping error rate, the CIRA-Q climatological model and signal residual phase pre-filtering are utilized to process the ARO residual phase. This more accurately modeled phase and less noisy received signal are shown to greatly reduce the bias caused by unwrapping error at lower

  16. Target tracking based on spatio-temporal fractal error

    NASA Astrophysics Data System (ADS)

    Allen, Brian S.

    2007-04-01

    This paper presents a novel approach to target tracking using a measurement process based on spatio-temporal fractal error. Moving targets are automatically detected using one-dimensional temporal fractal error. A template derived from the two-dimensional spatial fractal error is then extracted for a designated target to allow for correlation-based template matching in subsequent frames. The outputs of both the spatial and temporal fractal error components are combined and presented as input to a kinematic tracking filter. It is shown that combining the two outputs provides improved tracking performance in the presence of noise, occlusion, other moving objects, and when the target of interest stops moving. Furthermore, reconciliation of the spatial and temporal components also provides a useful mechanism for detecting occlusion and avoiding template drift, a problem typically present in correlation-based trackers. Results are demonstrated using airborne MWIR sequences from the DARPA VIVID dataset.

  17. Intent Inference and Syntactic Tracking with GMTI Measurements

    NASA Astrophysics Data System (ADS)

    Wang, Alex; Krishnamurthy, Vikram; Balaji, Bhashyam

    In conventional target tracking systems, human operators use the estimated target tracks to make higher level inference of the target behaviour/intent. This paper develops syntactic filtering algorithms that assist human operators by extracting spatial patterns from target tracks to identify suspicious/anomalous spatial trajectories. The targets' spatial trajectories are modeled by a stochastic context free grammar (SCFG) and a switched mode state space model. Bayesian filtering algorithms for stochastic context free grammars are presented for extracting the syntactic structure and illustrated for a ground moving target indicator (GMTI) radar example. The performance of the algorithms is tested with the experimental data collected using DRDC Ottawa's X-band Wideband Experimental Airborne Radar (XWEAR).

  18. Airborne gravity measurement over sea-ice: The western Weddel Sea

    SciTech Connect

    Brozena, J.; Peters, M. ); LaBrecque, J.; Bell, R.; Raymond, C. )

    1990-10-01

    An airborne gravity study of the western Weddel Sea, east of the Antarctic Peninsula, has shown that floating pack-ice provides a useful radar altimetric reference surface for altitude and vertical acceleration corrections surface for alititude and vertical acceleration corrections to airborne gravimetry. Airborne gravimetry provides an important alternative to satellite altimetry for the sea-ice covered regions of the world since satellite alimeters are not designed or intended to provide accurate geoidal heights in areas where significant sea-ice is present within the radar footprint. Errors in radar corrected airborne gravimetry are primarily sensitive to the variations in the second derivative of the sea-ice reference surface in the frequency pass-band of interest. With the exception of imbedded icebergs the second derivative of the pack-ice surface closely approximates that of the mean sea-level surface at wavelengths > 10-20 km. With the airborne method the percentage of ice coverage, the mixture of first and multi-year ice and the existence of leads and pressure ridges prove to be unimportant in determining gravity anomalies at scales of geophysical and geodetic interest, provided that the ice is floating and not grounded. In the Weddell study an analysis of 85 crosstrack miss-ties distributed over 25 data tracks yields an rms error of 2.2 mGals. Significant structural anomalies including the continental shelf and offsets and lineations interpreted as fracture zones recording the early spreading directions within the Weddell Sea are observed in the gravity map.

  19. Integrated Airborne and In-Situ Measurements over Land-Fast Ice near Barrow, AK.

    NASA Astrophysics Data System (ADS)

    Brozena, J. M.; Gardner, J. M.; Liang, R.; Ball, D.; Richter-Menge, J.; Claffey, K. J.; Abelev, A.; Hebert, D. A.; Jones, K.

    2014-12-01

    During March of 2014, the Naval Research Laboratory and the Cold Regions Research and Engineering Laboratory collected an integrated set of airborne and in-situ measurements over two areas of floating, but land-fast ice near the coast of Barrow, AK. The near-shore site was just north of Point Barrow, and the "offshore" site was ~ 20 km east of Point Barrow. The in-situ data provided ground-truth for airborne measurements from a scanning LiDAR (Riegl Q 560i), digital photogrammetry (Applanix DSS-439) and a snow radar procured from the Center for Remote Sensing of Ice Sheets of the University of Kansas. The objective of the survey was to aid our understanding of the use of the airborne data to calibrate/validate Cryosat-2 data. Sampling size or "footprint" plays a critical role in the attempt to compare in-situ measurements with airborne (or satellite) measurements. Thus the in-situ data were arranged to minimize aliasing. Ground measurements were collected along transects at both sites consisting of a 2 km long profile of snow depth and ice thickness measurements with periodic boreholes. A 60 m x 400 m swath of snow depth measurements was centered on this profile. Airborne data were collected on five overflights of the two transect areas. The LiDAR measured total freeboard (ice + snow) referenced to leads in the ice, and produced swaths 200-300 m wide. The radar measured snow thickness. The freeboard and snow thickness measurements are used to estimate ice thickness via isostasy and density estimates. The central swath of in situ snow depth data allows examination of the effects of cross-track variations considering the relatively large footprint of the snow radar. Assuming a smooth, flat surface the radar range resolution in air is < 4 cm, but the along-track sampling distance is ~ 3 m after unfocussed SAR processing. The width of the footprint varies from ~ 9 m up to about 40 m (beam-limited) for uneven surfaces. However, the radar could not resolve snow thickness

  20. Temporal decorrelation in repeat pass-radar interferometry

    NASA Technical Reports Server (NTRS)

    Villasenor, John; Zebker, Howard

    1992-01-01

    Correlation in pass-to-pass, interferometric radar can be degraded by thermal noise, lack of parallelism between the radar flight tracks, spatial baseline noise, and surficial change. The effects of decorrelation due to thermal noise can be easily evaluated and removed, while those due slight angular changes between flight tracks are negligible for data acquired using near-repeat orbits. Empirical results obtained using images of Death Valley confirm that as the baseline increases, the overall correlation decreases due to spatial baseline noise. It is shown that areas of Cottonball Basin in Death Valley remained unchanged over the three-week period for which data was obtained, while a heavily forested area in Oregon exhibited significant temporal decorrelation. Lava in central Oregon also appeared to decorrelate. The results demonstrate that generation of height maps of heavily vegetated areas using pass-to-pass interferometry is practical, provided that the time between passes is at most several weeks.

  1. Tracking dynamic team activity

    SciTech Connect

    Tambe, M.

    1996-12-31

    AI researchers are striving to build complex multi-agent worlds with intended applications ranging from the RoboCup robotic soccer tournaments, to interactive virtual theatre, to large-scale real-world battlefield simulations. Agent tracking - monitoring other agent`s actions and inferring their higher-level goals and intentions - is a central requirement in such worlds. While previous work has mostly focused on tracking individual agents, this paper goes beyond by focusing on agent teams. Team tracking poses the challenge of tracking a team`s joint goals and plans. Dynamic, real-time environments add to the challenge, as ambiguities have to be resolved in real-time. The central hypothesis underlying the present work is that an explicit team-oriented perspective enables effective team tracking. This hypothesis is instantiated using the model tracing technology employed in tracking individual agents. Thus, to track team activities, team models are put to service. Team models are a concrete application of the joint intentions framework and enable an agent to track team activities, regardless of the agent`s being a collaborative participant or a non-participant in the team. To facilitate real-time ambiguity resolution with team models: (i) aspects of tracking are cast as constraint satisfaction problems to exploit constraint propagation techniques; and (ii) a cost minimality criterion is applied to constrain tracking search. Empirical results from two separate tasks in real-world, dynamic environments one collaborative and one competitive - are provided.

  2. Observations of Soft Gamma Repeaters

    NASA Technical Reports Server (NTRS)

    Kouveliotou, Chryssa

    2004-01-01

    Magnetars (Soft Gamma Repeaters and Anomalous X-ray Pulsars) are a subclass of neutron stars characterized by their recurrent X-ray bursts. While in an active (bursting) state (lasting anywhere between days and years), they are emit&ng hundreds of predominantly soft (kT=30 kev), short (0.1-100 ms long) events. Their quiescent source x-ray light ewes exhibit puhlions rotational period rate changes (spin-down) indicate that their magnetic fields are extremely high, of the order of 10^14- 10^l5 G. Such high B-field objects, dubbed "magnetars", had been predicted to exist in 1992, but the first concrete observational evidence were obtained in 1998 for two of these sources. I will discuss here the history of Soft Gamma Repeaters, and their spectral, timing and flux characteristics both in the persistent and their burst emission.

  3. Mapping permafrost with airborne electromagnetics

    NASA Astrophysics Data System (ADS)

    Minsley, B. J.; Ball, L. B.; Bloss, B. R.; Kass, A.; Pastick, N.; Smith, B. D.; Voss, C. I.; Walsh, D. O.; Walvoord, M. A.; Wylie, B. K.

    2014-12-01

    Permafrost is a key characteristic of cold region landscapes, yet detailed assessments of how the subsurface distribution of permafrost impacts the environment, hydrologic systems, and infrastructure are lacking. Data acquired from several airborne electromagnetic (AEM) surveys in Alaska provide significant new insight into the spatial extent of permafrost over larger areas (hundreds to thousands of square kilometers) than can be mapped using ground-based geophysical methods or through drilling. We compare several AEM datasets from different areas of interior Alaska, and explore the capacity of these data to infer geologic structure, permafrost extent, and related hydrologic processes. We also assess the impact of fires on permafrost by comparing data from different burn years within similar geological environments. Ultimately, interpretations rely on understanding the relationship between electrical resistivity measured by AEM surveys and the physical properties of interest such as geology, permafrost, and unfrozen water content in the subsurface. These relationships are often ambiguous and non-unique, so additional information is useful for reducing uncertainty. Shallow (upper ~1m) permafrost and soil characteristics identified from remotely sensed imagery and field observations help to constrain and aerially extend near-surface AEM interpretations, where correlations between the AEM and remote sensing data are identified using empirical multivariate analyses. Surface nuclear magnetic resonance (sNMR) measurements quantify the contribution of unfrozen water at depth to the AEM-derived electrical resistivity models at several locations within one survey area. AEM surveys fill a critical data gap in the subsurface characterization of permafrost environments and will be valuable in future mapping and monitoring programs in cold regions.

  4. Active airborne contamination control using electrophoresis

    SciTech Connect

    Veatch, B.D.

    1994-06-01

    In spite of our best efforts, radioactive airborne contamination continues to be a formidable problem at many of the Department of Energy (DOE) weapons complex sites. For workers that must enter areas with high levels of airborne contamination, personnel protective equipment (PPE) can become highly restrictive, greatly diminishing productivity. Rather than require even more restrictive PPE for personnel in some situations, the Rocky Flats Plant (RFP) is actively researching and developing methods to aggressively combat airborne contamination hazards using electrophoretic technology. With appropriate equipment, airborne particulates can be effectively removed and collected for disposal in one simple process. The equipment needed to implement electrophoresis is relatively inexpensive, highly reliable, and very compact. Once airborne contamination levels are reduced, less PPE is required and a significant cost savings may be realized through decreased waste and maximized productivity. Preliminary ``cold,`` or non-radioactive, testing results at the RFP have shown the technology to be effective on a reasonable scale, with several potential benefits and an abundance of applications.

  5. Airborne laser communication technology and flight test

    NASA Astrophysics Data System (ADS)

    Meng, Li-xin; Zhang, Li-zhong; Li, Xiao-ming; Li, Ying-chao; Jiang, Hui-lin

    2015-11-01

    Reconnaissance aircraft is an important node of the space-air-ground integrated information network, on which equipped with a large number of high-resolution surveillance equipment, and need high speed communications equipment to transmit detected information in real time. Currently RF communication methods cannot meet the needs of communication bandwidth. Wireless laser communication has outstanding advantages high speed, high capacity, security, etc., is an important means to solve the high-speed information transmission of airborne platforms. In this paper, detailed analysis of how the system works, the system components, work processes, link power and the key technologies of airborne laser communication were discussed. On this basis, a prototype airborne laser communications was developed, and high-speed, long-distance communications tests were carried out between the two fixed-wing aircraft, and the airborne precision aiming, atmospheric laser communication impacts on laser communication were tested. The experiments ultimately realize that, the communication distance is 144km, the communication rate is 2.5Gbps. The Airborne laser communication experiments provide technical basis for the application of the conversion equipment.

  6. Airborne Gravimetry and Downward Continuation (Invited)

    NASA Astrophysics Data System (ADS)

    Jekeli, C.; Yang, H.; Kwon, J.

    2009-12-01

    Measuring the Earth’s gravity field using airborne instrumentation is fully operational and has been widely practiced for nearly three decades since its official debut in the early 1980s (S. Hammer: “Airborne Gravity is Here!”) coinciding with the precision kinematic positioning capability of GPS. Airborne gravimetry is undertaken for both efficient geophysical exploration purposes, as well as the determination of the regional geoid to aid in the modernization of height systems. Especially for the latter application, downward continuation of the data and combination with existing terrestrial gravimetry pose theoretical as well as practical challenges, which, on the other hand, create multiple processing possibilities. Downward continuation may be approached in various ways from the viewpoint of potential theory and the boundary-value problem to using gradients either estimated locally or computed from existing models. Logistical constraints imposed by the airborne survey, instrumental noise, and the intrinsic numerical instability of downward continuation all conspire to impact the final product in terms of achievable resolution and accuracy. In this paper, we review the theory of airborne gravimetry and the methodology of downward continuation, and provide a numerical comparison of possible schemes and their impact on geoid determination.

  7. A repeating fast radio burst

    NASA Astrophysics Data System (ADS)

    Spitler, L. G.; Scholz, P.; Hessels, J. W. T.; Bogdanov, S.; Brazier, A.; Camilo, F.; Chatterjee, S.; Cordes, J. M.; Crawford, F.; Deneva, J.; Ferdman, R. D.; Freire, P. C. C.; Kaspi, V. M.; Lazarus, P.; Lynch, R.; Madsen, E. C.; McLaughlin, M. A.; Patel, C.; Ransom, S. M.; Seymour, A.; Stairs, I. H.; Stappers, B. W.; van Leeuwen, J.; Zhu, W. W.

    2016-03-01

    Fast radio bursts are millisecond-duration astronomical radio pulses of unknown physical origin that appear to come from extragalactic distances. Previous follow-up observations have failed to find additional bursts at the same dispersion measure (that is, the integrated column density of free electrons between source and telescope) and sky position as the original detections. The apparent non-repeating nature of these bursts has led to the suggestion that they originate in cataclysmic events. Here we report observations of ten additional bursts from the direction of the fast radio burst FRB 121102. These bursts have dispersion measures and sky positions consistent with the original burst. This unambiguously identifies FRB 121102 as repeating and demonstrates that its source survives the energetic events that cause the bursts. Additionally, the bursts from FRB 121102 show a wide range of spectral shapes that appear to be predominantly intrinsic to the source and which vary on timescales of minutes or less. Although there may be multiple physical origins for the population of fast radio bursts, these repeat bursts with high dispersion measure and variable spectra specifically seen from the direction of FRB 121102 support an origin in a young, highly magnetized, extragalactic neutron star.

  8. A repeating fast radio burst.

    PubMed

    Spitler, L G; Scholz, P; Hessels, J W T; Bogdanov, S; Brazier, A; Camilo, F; Chatterjee, S; Cordes, J M; Crawford, F; Deneva, J; Ferdman, R D; Freire, P C C; Kaspi, V M; Lazarus, P; Lynch, R; Madsen, E C; McLaughlin, M A; Patel, C; Ransom, S M; Seymour, A; Stairs, I H; Stappers, B W; van Leeuwen, J; Zhu, W W

    2016-03-10

    Fast radio bursts are millisecond-duration astronomical radio pulses of unknown physical origin that appear to come from extragalactic distances. Previous follow-up observations have failed to find additional bursts at the same dispersion measure (that is, the integrated column density of free electrons between source and telescope) and sky position as the original detections. The apparent non-repeating nature of these bursts has led to the suggestion that they originate in cataclysmic events. Here we report observations of ten additional bursts from the direction of the fast radio burst FRB 121102. These bursts have dispersion measures and sky positions consistent with the original burst. This unambiguously identifies FRB 121102 as repeating and demonstrates that its source survives the energetic events that cause the bursts. Additionally, the bursts from FRB 121102 show a wide range of spectral shapes that appear to be predominantly intrinsic to the source and which vary on timescales of minutes or less. Although there may be multiple physical origins for the population of fast radio bursts, these repeat bursts with high dispersion measure and variable spectra specifically seen from the direction of FRB 121102 support an origin in a young, highly magnetized, extragalactic neutron star. PMID:26934226

  9. Color Image Processing and Object Tracking System

    NASA Technical Reports Server (NTRS)

    Klimek, Robert B.; Wright, Ted W.; Sielken, Robert S.

    1996-01-01

    This report describes a personal computer based system for automatic and semiautomatic tracking of objects on film or video tape, developed to meet the needs of the Microgravity Combustion and Fluids Science Research Programs at the NASA Lewis Research Center. The system consists of individual hardware components working under computer control to achieve a high degree of automation. The most important hardware components include 16-mm and 35-mm film transports, a high resolution digital camera mounted on a x-y-z micro-positioning stage, an S-VHS tapedeck, an Hi8 tapedeck, video laserdisk, and a framegrabber. All of the image input devices are remotely controlled by a computer. Software was developed to integrate the overall operation of the system including device frame incrementation, grabbing of image frames, image processing of the object's neighborhood, locating the position of the object being tracked, and storing the coordinates in a file. This process is performed repeatedly until the last frame is reached. Several different tracking methods are supported. To illustrate the process, two representative applications of the system are described. These applications represent typical uses of the system and include tracking the propagation of a flame front and tracking the movement of a liquid-gas interface with extremely poor visibility.

  10. A Prospective Study of Psychiatric Comorbidity and Recidivism Among Repeat DUI Offenders

    PubMed Central

    Nelson, Sarah E.; Belkin, Katerina; LaPlante, Debi A.; Bosworth, Leslie; Shaffer, Howard J.

    2015-01-01

    Psychiatric comorbidity has emerged as a key element distinguishing DUI offenders from others, and, in some cases, distinguishing repeat offenders from first-time offenders. This paper utilizes a prospective design to determine whether the comorbid disorders identified among repeat DUI offenders can predict recidivism. Seven hundred forty-three repeat DUI offenders were recruited from a two-week inpatient treatment program at which they received a standardized mental health assessment and followed across five years post-treatment to track DUI offense, motor vehicle-related offenses, and general criminal offenses. Psychiatric comorbidity, though it did not predict DUI recidivism specifically, predicted criminal re-offense more generally. In addition, there was a specific relationship between lifetime attention deficit disorder and repeated motor vehicle-related offenses. These findings suggest that for many repeat offenders, DUI is one outlet in a constellation of criminal behavior, and that psychiatric comorbidity increases vulnerability for criminal re-offense. PMID:26539339

  11. Source apportionment of airborne particulates through receptor modeling: Indian scenario

    NASA Astrophysics Data System (ADS)

    Banerjee, Tirthankar; Murari, Vishnu; Kumar, Manish; Raju, M. P.

    2015-10-01

    Airborne particulate chemistry mostly governed by associated sources and apportionment of specific sources is extremely essential to delineate explicit control strategies. The present submission initially deals with the publications (1980s-2010s) of Indian origin which report regional heterogeneities of particulate concentrations with reference to associated species. Such meta-analyses clearly indicate the presence of reservoir of both primary and secondary aerosols in different geographical regions. Further, identification of specific signatory molecules for individual source category was also evaluated in terms of their scientific merit and repeatability. Source signatures mostly resemble international profile while, in selected cases lack appropriateness. In India, source apportionment (SA) of airborne particulates was initiated way back in 1985 through factor analysis, however, principal component analysis (PCA) shares a major proportion of applications (34%) followed by enrichment factor (EF, 27%), chemical mass balance (CMB, 15%) and positive matrix factorization (PMF, 9%). Mainstream SA analyses identify earth crust and road dust resuspensions (traced by Al, Ca, Fe, Na and Mg) as a principal source (6-73%) followed by vehicular emissions (traced by Fe, Cu, Pb, Cr, Ni, Mn, Ba and Zn; 5-65%), industrial emissions (traced by Co, Cr, Zn, V, Ni, Mn, Cd; 0-60%), fuel combustion (traced by K, NH4+, SO4-, As, Te, S, Mn; 4-42%), marine aerosols (traced by Na, Mg, K; 0-15%) and biomass/refuse burning (traced by Cd, V, K, Cr, As, TC, Na, K, NH4+, NO3-, OC; 1-42%). In most of the cases, temporal variations of individual source contribution for a specific geographic region exhibit radical heterogeneity possibly due to unscientific orientation of individual tracers for specific source and well exaggerated by methodological weakness, inappropriate sample size, implications of secondary aerosols and inadequate emission inventories. Conclusively, a number of challenging

  12. Tracking toxic chemicals

    NASA Astrophysics Data System (ADS)

    Showstack, Randy

    A new report tracking industrial pollution in North America indicates some good news, in terms of downward trends in the release and transfer of these substances.The July report, which tracks 165 chemicals released in the United States and Canada, shows that the total amount of 3.2 million tonnes of chemical releases and transfers from industrial facilities tracked by the North American Commission for Environmental Cooperation (CEC) decreased by 2% overall from 1995 to 1998.

  13. Improved Airborne Gravity Results Using New Relative Gravity Sensor Technology

    NASA Astrophysics Data System (ADS)

    Brady, N.

    2013-12-01

    Airborne gravity data has contributed greatly to our knowledge of subsurface geophysics particularly in rugged and otherwise inaccessible areas such as Antarctica. Reliable high quality GPS data has renewed interest in improving the accuracy of airborne gravity systems and recent improvements in the electronic control of the sensor have increased the accuracy and ability of the classic Lacoste and Romberg zero length spring gravity meters to operate in turbulent air conditions. Lacoste and Romberg type gravity meters provide increased sensitivity over other relative gravity meters by utilizing a mass attached to a horizontal beam which is balanced by a ';zero length spring'. This type of dynamic gravity sensor is capable of measuring gravity changes on the order of 0.05 milliGals in laboratory conditions but more commonly 0.7 to 1 milliGal in survey use. The sensor may have errors induced by the electronics used to read the beam position as well as noise induced by unwanted accelerations, commonly turbulence, which moves the beam away from its ideal balance position otherwise known as the reading line. The sensor relies on a measuring screw controlled by a computer which attempts to bring the beam back to the reading line position. The beam is also heavily damped so that it does not react to most unwanted high frequency accelerations. However this heavily damped system is slow to react, particularly in turns where there are very high Eotvos effects. New sensor technology utilizes magnetic damping of the beam coupled with an active feedback system which acts to effectively keep the beam locked at the reading line position. The feedback system operates over the entire range of the system so there is now no requirement for a measuring screw. The feedback system operates at very high speed so that even large turbulent events have minimal impact on data quality and very little, if any, survey line data is lost because of large beam displacement errors. Airborne testing

  14. Airborne Microalgae: Insights, Opportunities, and Challenges.

    PubMed

    Tesson, Sylvie V M; Skjøth, Carsten Ambelas; Šantl-Temkiv, Tina; Löndahl, Jakob

    2016-04-01

    Airborne dispersal of microalgae has largely been a blind spot in environmental biological studies because of their low concentration in the atmosphere and the technical limitations in investigating microalgae from air samples. Recent studies show that airborne microalgae can survive air transportation and interact with the environment, possibly influencing their deposition rates. This minireview presents a summary of these studies and traces the possible route, step by step, from established ecosystems to new habitats through air transportation over a variety of geographic scales. Emission, transportation, deposition, and adaptation to atmospheric stress are discussed, as well as the consequences of their dispersal on health and the environment and state-of-the-art techniques to detect and model airborne microalga dispersal. More-detailed studies on the microalga atmospheric cycle, including, for instance, ice nucleation activity and transport simulations, are crucial for improving our understanding of microalga ecology, identifying microalga interactions with the environment, and preventing unwanted contamination events or invasions. PMID:26801574

  15. Airborne pollen trends in the Iberian Peninsula.

    PubMed

    Galán, C; Alcázar, P; Oteros, J; García-Mozo, H; Aira, M J; Belmonte, J; Diaz de la Guardia, C; Fernández-González, D; Gutierrez-Bustillo, M; Moreno-Grau, S; Pérez-Badía, R; Rodríguez-Rajo, J; Ruiz-Valenzuela, L; Tormo, R; Trigo, M M; Domínguez-Vilches, E

    2016-04-15

    Airborne pollen monitoring is an effective tool for studying the reproductive phenology of anemophilous plants, an important bioindicator of plant behavior. Recent decades have revealed a trend towards rising airborne pollen concentrations in Europe, attributing these trends to an increase in anthropogenic CO2 emissions and temperature. However, the lack of water availability in southern Europe may prompt a trend towards lower flowering intensity, especially in herbaceous plants. Here we show variations in flowering intensity by analyzing the Annual Pollen Index (API) of 12 anemophilous taxa across 12 locations in the Iberian Peninsula, over the last two decades, and detecting the influence of the North Atlantic Oscillation (NAO). Results revealed differences in the distribution and flowering intensity of anemophilous species. A negative correlation was observed between airborne pollen concentrations and winter averages of the NAO index. This study confirms that changes in rainfall in the Mediterranean region, attributed to climate change, have an important impact on the phenology of plants. PMID:26803684

  16. Airborne Microalgae: Insights, Opportunities, and Challenges

    PubMed Central

    Skjøth, Carsten Ambelas; Šantl-Temkiv, Tina; Löndahl, Jakob

    2016-01-01

    Airborne dispersal of microalgae has largely been a blind spot in environmental biological studies because of their low concentration in the atmosphere and the technical limitations in investigating microalgae from air samples. Recent studies show that airborne microalgae can survive air transportation and interact with the environment, possibly influencing their deposition rates. This minireview presents a summary of these studies and traces the possible route, step by step, from established ecosystems to new habitats through air transportation over a variety of geographic scales. Emission, transportation, deposition, and adaptation to atmospheric stress are discussed, as well as the consequences of their dispersal on health and the environment and state-of-the-art techniques to detect and model airborne microalga dispersal. More-detailed studies on the microalga atmospheric cycle, including, for instance, ice nucleation activity and transport simulations, are crucial for improving our understanding of microalga ecology, identifying microalga interactions with the environment, and preventing unwanted contamination events or invasions. PMID:26801574

  17. Airborne space laser communication system and experiments

    NASA Astrophysics Data System (ADS)

    Li, Xiao-Ming; Zhang, Li-zhong; Meng, Li-Xin

    2015-11-01

    Airborne space laser communication is characterized by its high speed, anti-electromagnetic interference, security, easy to assign. It has broad application in the areas of integrated space-ground communication networking, military communication, anti-electromagnetic communication. This paper introduce the component and APT system of the airborne laser communication system design by Changchun university of science and technology base on characteristic of airborne laser communication and Y12 plan, especially introduce the high communication speed and long distance communication experiment of the system that among two Y12 plans. In the experiment got the aim that the max communication distance 144Km, error 10-6 2.5Gbps - 10-7 1.5Gbps capture probability 97%, average capture time 20s. The experiment proving the adaptability of the APT and the high speed long distance communication.

  18. Tracking in anatomic pathology.

    PubMed

    Pantanowitz, Liron; Mackinnon, Alexander C; Sinard, John H

    2013-12-01

    Bar code-based tracking solutions, long present in clinical pathology laboratories, have recently made an appearance in anatomic pathology (AP) laboratories. Tracking of AP "assets" (specimens, blocks, slides) can enhance laboratory efficiency, promote patient safety, and improve patient care. Routing of excess clinical material into research laboratories and biorepositories are other avenues that can benefit from tracking of AP assets. Implementing tracking is not as simple as installing software and turning it on. Not all tracking solutions are alike. Careful analysis of laboratory workflow is needed before implementing tracking to assure that this solution will meet the needs of the laboratory. Such analysis will likely uncover practices that may need to be modified before a tracking system can be deployed. Costs that go beyond simply that of purchasing software will be incurred and need to be considered in the budgeting process. Finally, people, not technology, are the key to assuring quality. Tracking will require significant changes in workflow and an overall change in the culture of the laboratory. Preparation, training, buy-in, and accountability of the people involved are crucial to the success of this process. This article reviews the benefits, available technology, underlying principles, and implementation of tracking solutions for the AP and research laboratory. PMID:23634908

  19. Retrieval of aerosol optical thickness over land from airborne polarized measurements in Tianjin and Tangshan

    NASA Astrophysics Data System (ADS)

    Wang, Han; Sun, Xiaobing; Hou, Weizhen; Chen, Cheng; Hong, Jin

    2015-03-01

    New developed sensor was called Atmosphere Multi-angle Polarization Radiometer (AMPR). It provides airborne multi-spectral, multi-angular and polarized measurements. Based on the measurements, a method to retrieve aerosol optical thickness (AOT) was developed. To reduce the ambiguity in retrieval algorithm, the key characteristics of aerosol model over East Asia are constrained. Initial surface reflectance was estimated from measurements at 1640 nm. With iteration the surface polarized reflectance tends to the real value together with AOT. Retrieved cases were selected from measurements in Tianjin. Validation between AOTs from AMPR and CE318 is encouraging. The AOTs along the track shows reasonable temporal and spatial variation.

  20. Initial airborne CO{sub 2} DIAL measurements: Discussion of results and data analysis considerations

    SciTech Connect

    Tiee, J.J.; Foy, B.R.; Quick, C.R.

    1997-07-01

    A detailed discussion of airborne CO{sub 2}, DIAL measurements obtained from the first joint N-ABLE field campaign at INEL is presented. System performance characteristics, including return signal strength, averaging statistics, and temporal correlation as well as multi-line DIAL spectral data are discussed. In particular, we review data acquisition and analysis strategies pertinent to chemical detection from a moving platform, such as range determination and correction, and return signal processing (waveform vs. box-car integration, baseline correction). We also report observed effects and variations due to near-field light scattering, pointing and tracking stability, and stack-release plume dynamics.

  1. An Airborne Conical Scanning Millimeter-Wave Imaging Radiometer (CoSMIR)

    NASA Technical Reports Server (NTRS)

    Piepmeier, J.; Racette, P.; Wang, J.; Crites, A.; Doiron, T.; Engler, C.; Lecha, J.; Powers, M.; Simon, E.; Triesky, M.; Krebs, Carolyn A. (Technical Monitor)

    2001-01-01

    An airborne Conical Scanning Millimeter-wave Imaging Radiometer (CoSMIR) for high-altitude observations from the NASA Research Aircraft (ER-2) is discussed. The primary application of the CoSMIR is water vapor profile remote sensing. Four radiometers operating at 50 (three channels), 92, 150, and 183 (three channels) GHz provide spectral coverage identical to nine of the Special Sensor Microwave Imager/Sounder (SSMIS) high-frequency channels. Constant polarization-basis conical and cross-track scanning capabilities are achieved using an elevation-under-azimuth two-axis gimbals.

  2. Delineating and Defining the Boundaries of an Active Landslide in the Rainforest of Puerto Rico Using a Combination of Airborne and Terrestrial LIDAR Data

    NASA Astrophysics Data System (ADS)

    Wang, G.; Joyce, J.; Phillips, D. A.; Shrestha, R. L.; Carter, W. E.

    2013-05-01

    Light detection and ranging (LIDAR) is a remote sensing technique that uses light, often using pulses from a laser to measure the distance to a target. Both terrestrial and airborne based LIDAR techniques have been frequently used to map landslides. Airborne LIDAR has the advantage of identifying large scarps of landslides covered by tree canopies and is widely applied in identifying historical and current active landslides hidden in forested areas. However, because landslides naturally have relatively small vertical surface deformation in the foot area, it is practically difficult to identify the margins of landslide foot area with the limited spatial resolution (few decimeters) of airborne LIDAR. Alternatively, ground-based LIDAR can achieve resolution of several centimeters and also has the advantages of being portable, repeatable, and less costly. Thus ground based LIDAR can be used to identify small deformations in landslide foot areas by differencing repeated Terrestrial Laser Scanning (TLS) surveys. This study demonstrates a method of identifying the superficial boundaries as well as the bottom boundary (sliding plane) of an active landslide in National Rainforest Park, Puerto Rico, USA, using the combination of ground based and airborne LIDAR data. The method of combining terrestrial and airborne LIDAR data can be used to study landslides in other regions. This study indicates that intensity and density of laser point clouds are remarkably useful in identifying superficial boundaries of landslides.

  3. Approaches to detection of airborne biological agents

    NASA Astrophysics Data System (ADS)

    Chang, An-Cheng; Tabacco, Mary Beth

    2009-05-01

    Three approaches to detection of biological agents based on biological processes will be presented. The first example demonstrates the use of dendrimers to deliver a membrane-impermeable fluorescent dye into live bacteria, similar to viral infection and delivery of DNA/RNA into a bacterial cell. The second example mimics collection and capture of airborne biological particles by the respiratory mucosa through the use of a hygroscopic sensing membrane. The third example is based on the use of multiple fluorescent probes with diverse functionalities to detect airborne biological agents in a manner similar to the olfactory receptors in the nasal tract.

  4. NASA Airborne Lidar 1982-1984 Flights Data and Information

    Atmospheric Science Data Center

    2014-08-06

    NASA Airborne Lidar 1982-1984 Flights Data from the 1982 NASA Langley Airborne Lidar flights following the eruption of El Chichon ... continuing to January 1984. Transcribed from the following NASA Tech Reports: McCormick, M. P., and M. T. Osborn, Airborne lidar ...

  5. 14 CFR 135.175 - Airborne weather radar equipment requirements.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airborne weather radar equipment... Aircraft and Equipment § 135.175 Airborne weather radar equipment requirements. (a) No person may operate a large, transport category aircraft in passenger-carrying operations unless approved airborne...

  6. 14 CFR 121.357 - Airborne weather radar equipment requirements.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airborne weather radar equipment... § 121.357 Airborne weather radar equipment requirements. (a) No person may operate any transport... December 31, 1964, unless approved airborne weather radar equipment has been installed in the airplane....

  7. 14 CFR 135.175 - Airborne weather radar equipment requirements.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airborne weather radar equipment... Aircraft and Equipment § 135.175 Airborne weather radar equipment requirements. (a) No person may operate a large, transport category aircraft in passenger-carrying operations unless approved airborne...

  8. 14 CFR 125.223 - Airborne weather radar equipment requirements.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airborne weather radar equipment... Equipment Requirements § 125.223 Airborne weather radar equipment requirements. (a) No person may operate an airplane governed by this part in passenger-carrying operations unless approved airborne weather...

  9. 14 CFR 121.357 - Airborne weather radar equipment requirements.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airborne weather radar equipment... § 121.357 Airborne weather radar equipment requirements. (a) No person may operate any transport... December 31, 1964, unless approved airborne weather radar equipment has been installed in the airplane....

  10. 14 CFR 125.223 - Airborne weather radar equipment requirements.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airborne weather radar equipment... Equipment Requirements § 125.223 Airborne weather radar equipment requirements. (a) No person may operate an airplane governed by this part in passenger-carrying operations unless approved airborne weather...

  11. 14 CFR 135.175 - Airborne weather radar equipment requirements.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airborne weather radar equipment... Aircraft and Equipment § 135.175 Airborne weather radar equipment requirements. (a) No person may operate a large, transport category aircraft in passenger-carrying operations unless approved airborne...

  12. 14 CFR 125.223 - Airborne weather radar equipment requirements.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airborne weather radar equipment... Equipment Requirements § 125.223 Airborne weather radar equipment requirements. (a) No person may operate an airplane governed by this part in passenger-carrying operations unless approved airborne weather...

  13. 14 CFR 121.357 - Airborne weather radar equipment requirements.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airborne weather radar equipment... § 121.357 Airborne weather radar equipment requirements. (a) No person may operate any transport... December 31, 1964, unless approved airborne weather radar equipment has been installed in the airplane....

  14. 14 CFR 125.223 - Airborne weather radar equipment requirements.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airborne weather radar equipment... Equipment Requirements § 125.223 Airborne weather radar equipment requirements. (a) No person may operate an airplane governed by this part in passenger-carrying operations unless approved airborne weather...

  15. 14 CFR 135.175 - Airborne weather radar equipment requirements.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airborne weather radar equipment... Aircraft and Equipment § 135.175 Airborne weather radar equipment requirements. (a) No person may operate a large, transport category aircraft in passenger-carrying operations unless approved airborne...

  16. 14 CFR 121.357 - Airborne weather radar equipment requirements.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airborne weather radar equipment... § 121.357 Airborne weather radar equipment requirements. (a) No person may operate any transport... December 31, 1964, unless approved airborne weather radar equipment has been installed in the airplane....

  17. 14 CFR 125.223 - Airborne weather radar equipment requirements.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airborne weather radar equipment... Equipment Requirements § 125.223 Airborne weather radar equipment requirements. (a) No person may operate an airplane governed by this part in passenger-carrying operations unless approved airborne weather...

  18. 14 CFR 121.357 - Airborne weather radar equipment requirements.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airborne weather radar equipment... § 121.357 Airborne weather radar equipment requirements. (a) No person may operate any transport... December 31, 1964, unless approved airborne weather radar equipment has been installed in the airplane....

  19. 14 CFR 135.175 - Airborne weather radar equipment requirements.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airborne weather radar equipment... Aircraft and Equipment § 135.175 Airborne weather radar equipment requirements. (a) No person may operate a large, transport category aircraft in passenger-carrying operations unless approved airborne...

  20. Telomerase Repeated Amplification Protocol (TRAP)

    PubMed Central

    Mender, Ilgen; Shay, Jerry W.

    2016-01-01

    Telomeres are found at the end of eukaryotic linear chromosomes, and proteins that bind to telomeres protect DNA from being recognized as double-strand breaks thus preventing end-to-end fusions (Griffith et al., 1999). However, due to the end replication problem and other factors such as oxidative damage, the limited life span of cultured cells (Hayflick limit) results in progressive shortening of these protective structures (Hayflick and Moorhead, 1961; Olovnikov, 1973). The ribonucleoprotein enzyme complex telomerase-consisting of a protein catalytic component hTERT and a functional RNA component hTR or hTERC- counteracts telomere shortening by adding telomeric repeats to the end of chromosomes in ~90% of primary human tumors and in some transiently proliferating stem-like cells (Shay and Wright, 1996; Shay and Wright, 2001). This results in continuous proliferation of cells which is a hallmark of cancer. Therefore, telomere biology has a central role in aging, cancer progression/metastasis as well as targeted cancer therapies. There are commonly used methods in telomere biology such as Telomere Restriction Fragment (TRF) (Mender and Shay, 2015b), Telomere Repeat Amplification Protocol (TRAP) and Telomere dysfunction Induced Foci (TIF) analysis (Mender and Shay, 2015a). In this detailed protocol we describe Telomere Repeat Amplification Protocol (TRAP). The TRAP assay is a popular method to determine telomerase activity in mammalian cells and tissue samples (Kim et al., 1994). The TRAP assay includes three steps: extension, amplification, and detection of telomerase products. In the extension step, telomeric repeats are added to the telomerase substrate (which is actually a non telomeric oligonucleotide, TS) by telomerase. In the amplification step, the extension products are amplified by the polymerase chain reaction (PCR) using specific primers (TS upstream primer and ACX downstream primer) and in the detection step, the presence or absence of telomerase is

  1. Accumulate Repeat Accumulate Coded Modulation

    NASA Technical Reports Server (NTRS)

    Abbasfar, Aliazam; Divsalar, Dariush; Yao, Kung

    2004-01-01

    In this paper we propose an innovative coded modulation scheme called 'Accumulate Repeat Accumulate Coded Modulation' (ARA coded modulation). This class of codes can be viewed as serial turbo-like codes, or as a subclass of Low Density Parity Check (LDPC) codes that are combined with high level modulation. Thus at the decoder belief propagation can be used for iterative decoding of ARA coded modulation on a graph, provided a demapper transforms the received in-phase and quadrature samples to reliability of the bits.

  2. Can Tracking Improve Learning?

    ERIC Educational Resources Information Center

    Duflo, Esther; Dupas, Pascaline; Kremer, Michael

    2009-01-01

    Tracking students into different classrooms according to their prior academic performance is controversial among both scholars and policymakers. If teachers find it easier to teach a homogeneous group of students, tracking could enhance school effectiveness and raise test scores of both low- and high-ability students. If students benefit from…

  3. On the Wrong Track.

    ERIC Educational Resources Information Center

    Black, Susan

    1992-01-01

    By any measure--student achievement, social development, or democratic values--ability grouping and tracking practices are indefensible and unsupported by research. Tracking allows schools to practice in-school segregation and perpetuate unequal opportunities and unequal socialization within classrooms. Jonathan Kozol's investigation shows how…

  4. Large scale tracking algorithms.

    SciTech Connect

    Hansen, Ross L.; Love, Joshua Alan; Melgaard, David Kennett; Karelitz, David B.; Pitts, Todd Alan; Zollweg, Joshua David; Anderson, Dylan Z.; Nandy, Prabal; Whitlow, Gary L.; Bender, Daniel A.; Byrne, Raymond Harry

    2015-01-01

    Low signal-to-noise data processing algorithms for improved detection, tracking, discrimination and situational threat assessment are a key research challenge. As sensor technologies progress, the number of pixels will increase signi cantly. This will result in increased resolution, which could improve object discrimination, but unfortunately, will also result in a significant increase in the number of potential targets to track. Many tracking techniques, like multi-hypothesis trackers, suffer from a combinatorial explosion as the number of potential targets increase. As the resolution increases, the phenomenology applied towards detection algorithms also changes. For low resolution sensors, "blob" tracking is the norm. For higher resolution data, additional information may be employed in the detection and classfication steps. The most challenging scenarios are those where the targets cannot be fully resolved, yet must be tracked and distinguished for neighboring closely spaced objects. Tracking vehicles in an urban environment is an example of such a challenging scenario. This report evaluates several potential tracking algorithms for large-scale tracking in an urban environment.

  5. Explaining cloud chamber tracks

    SciTech Connect

    Broyles, A.A.

    1992-06-16

    The operation of many detection devices is usually explained in terms of the ionization tracks produced by particles despite the fact that the corresponding incident wave functions extended over the entire sensitive regions of the detectors. The mechanisms by which the wave function appears to collapse to a track is analyzed here.

  6. TMDL TRACKING SYSTEM

    EPA Science Inventory

    Resource Purpose:The TMDL Tracking System database contains information on the waters listed under section 303(d) of the Clean Water Act and to track those listed waters through TMDL development. The purpose of the database is to allow EPA, the States/Territories/Tribes, ...

  7. Incentives from Curriculum Tracking

    ERIC Educational Resources Information Center

    Koerselman, Kristian

    2013-01-01

    Curriculum tracking creates incentives in the years before its start, and we should therefore expect test scores to be higher during those years. I find robust evidence for incentive effects of tracking in the UK based on the UK comprehensive school reform. Results from the Swedish comprehensive school reform are inconclusive. Internationally, I…

  8. Track record in meteorites

    NASA Astrophysics Data System (ADS)

    Durrani, S. A.

    1981-02-01

    The use of nuclear-track analysis in meteoritic crystals with reference to several areas of research is reviewed. The applications discussed include: fission-track retention ages and cooling rates of meteoritic parent bodies, cosmic-ray studies, determination of pre-atmospheric sizes of meteorites, and search for superheavy elements.

  9. 2 Tracks for Faculty

    ERIC Educational Resources Information Center

    Wilson, Robin

    2012-01-01

    The academic work force has been transformed over the past several decades, less by design than out of expediency. In 1969, professors who were either tenured or tenure-track made up 78 percent of the faculty. Those working part time made up only 18.5 percent. By 2009, those proportions had almost flipped, with tenured and tenure-track making up…

  10. UWB Tracking Software Development

    NASA Technical Reports Server (NTRS)

    Gross, Julia; Arndt, Dickey; Ngo, Phong; Phan, Chau; Dusl, John; Ni, Jianjun; Rafford, Melinda

    2006-01-01

    An Ultra-Wideband (UWB) two-cluster Angle of Arrival (AOA) tracking prototype system is currently being developed and tested at NASA Johnson Space Center for space exploration applications. This talk discusses the software development efforts for this UWB two-cluster AOA tracking system. The role the software plays in this system is to take waveform data from two UWB radio receivers as an input, feed this input into an AOA tracking algorithm, and generate the target position as an output. The architecture of the software (Input/Output Interface and Algorithm Core) will be introduced in this talk. The development of this software has three phases. In Phase I, the software is mostly Matlab driven and calls C++ socket functions to provide the communication links to the radios. This is beneficial in the early stage when it is necessary to frequently test changes in the algorithm. Phase II of the development is to have the software mostly C++ driven and call a Matlab function for the AOA tracking algorithm. This is beneficial in order to send the tracking results to other systems and also to improve the tracking update rate of the system. The third phase is part of future work and is to have the software completely C++ driven with a graphics user interface. This software design enables the fine resolution tracking of the UWB two-cluster AOA tracking system.

  11. Lunar Airborne Dust Toxicity Hazard Assessments (Invited)

    NASA Astrophysics Data System (ADS)

    Cooper, B. L.; McKay, D. S.; Taylor, L. A.; Wallace, W. T.; James, J.; Riofrio, L.; Gonzalez, C. P.

    2009-12-01

    The Lunar Airborne Dust Toxicity Assessment Group (LADTAG) is developing data to set the permissible limits for human exposure to lunar dust. This standard will guide the design of airlocks and ports for EVA, as well as the requirements for filtering and monitoring the atmosphere in habitable vehicles, rovers and other modules. LADTAG’s recommendation for permissible exposure limits will be delivered to the Constellation Program in late 2010. The current worst-case exposure limit of 0.05 mg/m3, estimated by LADTAG in 2006, reflects the concern that lunar dust may be as toxic as quartz dust. Freshly-ground quartz is known to be more toxic than un-ground quartz dust. Our research has shown that the surfaces of lunar soil grains can be more readily activated by grinding than quartz. Activation was measured by the amount of free radicals generated—activated simulants generate Reactive Oxygen Species (ROS) i.e., production of hydroxyl free radicals. Of the various influences in the lunar environment, micrometeorite bombardment probably creates the most long-lasting reactivity on the surfaces of grains, although solar wind impingement and short-wavelength UV radiation also contribute. The comminution process creates fractured surfaces with unsatisfied bonds. When these grains are inhaled and carried into the lungs, they will react with lung surfactant and cells, potentially causing tissue damage and disease. Tests on lunar simulants have shown that dissolution and leaching of metals can occur when the grains are exposed to water—the primary component of lung fluid. However, simulants may behave differently than actual lunar soils. Rodent toxicity testing will be done using the respirable fraction of actual lunar soils (particles with physical size of less than 2.5 micrometers). We are currently separating the fine material from the coarser material that comprises >95% of the mass of each soil sample. Dry sieving is not practical in this size range, so a new system

  12. Improved Tracking of an Atomic-Clock Resonance Transition

    NASA Technical Reports Server (NTRS)

    Prestage, John D.; Chung, Sang K.; Tu, Meirong

    2010-01-01

    An improved method of making an electronic oscillator track the frequency of an atomic-clock resonance transition is based on fitting a theoretical nonlinear curve to measurements at three oscillator frequencies within the operational frequency band of the transition (in other words, at three points within the resonance peak). In the measurement process, the frequency of a microwave oscillator is repeatedly set at various offsets from the nominal resonance frequency, the oscillator signal is applied in a square pulse of the oscillator signal having a suitable duration (typically, of the order of a second), and, for each pulse at each frequency offset, fluorescence photons of the transition in question are counted. As described below, the counts are used to determine a new nominal resonance frequency. Thereafter, offsets are determined with respect to the new resonance frequency. The process as described thus far is repeated so as to repeatedly adjust the oscillator to track the most recent estimate of the nominal resonance frequency.

  13. Crowding by a repeating pattern

    PubMed Central

    Rosen, Sarah; Pelli, Denis G.

    2015-01-01

    Theinability to recognize a peripheral target among flankers is called crowding. For a foveal target, crowding can be distinguished from overlap masking by its sparing of detection, linear scaling with eccentricity, and invariance with target size.Crowding depends on the proximity and similarity of the flankers to the target. Flankers that are far from or dissimilar to the target do not crowd it. On a gray page, text whose neighboring letters have different colors, alternately black and white, has enough dissimilarity that it might escape crowding. Since reading speed is normally limited by crowding, escape from crowding should allow faster reading. Yet reading speed is unchanged (Chung & Mansfield, 2009). Why? A recent vernier study found that using alternating-color flankers produces strong crowding (Manassi, Sayim, & Herzog, 2012). Might that effect occur with letters and reading? Critical spacing is the minimum center-to-center target–flanker spacing needed to correctly identify the target. We measure it for a target letter surrounded by several equidistant flanker letters of the same polarity, opposite polarity, or mixed polarity: alternately white and black. We find strong crowding in the alternating condition, even though each flanker letter is beyond its own critical spacing (as measured in a separate condition). Thus a periodic repeating pattern can produce crowding even when the individual elements do not. Further, in all conditions we find that, once a periodic pattern repeats (two cycles), further repetition does not affect critical spacing of the innermost flanker. PMID:26024457

  14. Repeating firing fields of CA1 neurons shift forward in response to increasing angular velocity.

    PubMed

    Cowen, Stephen L; Nitz, Douglas A

    2014-01-01

    Self-motion information influences spatially-specific firing patterns exhibited by hippocampal neurons. Moreover, these firing patterns can repeat across similar subsegments of an environment, provided that there is similarity of path shape and head orientations across subsegments. The influence of self-motion variables on repeating fields remains to be determined. To investigate the role of path shape and angular rotation on hippocampal activity, we recorded the activity of CA1 neurons from rats trained to run on spiral-shaped tracks. During inbound traversals of circular-spiral tracks, angular velocity increases continuously. Under this condition, most neurons (74%) exhibited repeating fields across at least three adjacent loops. Of these neurons, 86% exhibited forward shifts in the angles of field centers relative to centers on preceding loops. Shifts were absent on squared-spiral tracks, minimal and less reliable on concentric-circle tracks, and absent on outward-bound runs on circular-spiral tracks. However, outward-bound runs on the circular-spiral track in the dark were associated with backward shifts. Together, the most parsimonious interpretation of the results is that continuous increases or decreases in angular velocity are particularly effective at shifting the center of mass of repeating fields, although it is also possible that a nonlinear integration of step counts contributes to the shift. Furthermore, the unexpected absence of field shifts during outward journeys in light (but not darkness) suggests visual cues around the goal location anchored the map of space to an allocentric reference frame. PMID:24381284

  15. TRACKED VEHICLE Rev 75

    SciTech Connect

    Raby, Eric Y.

    2007-05-08

    Revision 75 of the Tracked Vehicle software is a soft real-time simulation of a differentially steered, tracked mobile robot, which, because of the track flippers, resembles the iRobot PackBot (http://www.irobot.com/). Open source libraries are used for the physics engine (http://www.ode.org/), the display and user interface (http://www.mathies.com/cpw/), and the program command line and configuration file parameters (http://www.boost.org/). The simulation can be controlled by a USB joystick or the keyboard. The configuration file contains demonstration model parameters of no particular vehicle. This simulation can be used as a starting point for those doing tracked vehicle simulations. This simulation software is essentially a research tool which can be modified and adapted for certain types of tracked vehicle research. An open source license allows an individual researchers to tailor the code to their specific research needs.

  16. TRACKED VEHICLE Rev 75

    2007-05-08

    Revision 75 of the Tracked Vehicle software is a soft real-time simulation of a differentially steered, tracked mobile robot, which, because of the track flippers, resembles the iRobot PackBot (http://www.irobot.com/). Open source libraries are used for the physics engine (http://www.ode.org/), the display and user interface (http://www.mathies.com/cpw/), and the program command line and configuration file parameters (http://www.boost.org/). The simulation can be controlled by a USB joystick or the keyboard. The configuration file contains demonstration model parametersmore » of no particular vehicle. This simulation can be used as a starting point for those doing tracked vehicle simulations. This simulation software is essentially a research tool which can be modified and adapted for certain types of tracked vehicle research. An open source license allows an individual researchers to tailor the code to their specific research needs.« less

  17. NASA COAST and OCEANIA Airborne Missions in Support of Ecosystem and Water Quality Research in the Coastal Zone

    NASA Technical Reports Server (NTRS)

    Guild, Liane S.; Hooker, Stanford B.; Kudela, Raphael; Morrow, John; Russell, Philip; Myers, Jeffrey; Dunagan, Stephen; Palacios, Sherry; Livingston, John; Negrey, Kendra; Torres-Perez, Juan

    2015-01-01

    ecosystems. Simultaneous measurements supporting empirical atmospheric correction of image data were accomplished using the Ames Airborne Tracking Sunphotometer (AATS-14). Flight operations are presented for the instrument payloads using the CIRPAS Twin Otter flown over Monterey Bay during the seasonal fall algal bloom in 2011 (COAST) and 2013 (OCEANIA) to support bio-optical measurements of phytoplankton for coastal zone research. Further, this airborne capability can be responsive to first flush rain events that deliver higher concentrations of sediments and pollution to coastal waters via watersheds and overland flow.

  18. Airborne Satcom Terminal Research at NASA Glenn

    NASA Technical Reports Server (NTRS)

    Hoder, Doug; Zakrajsek, Robert

    2002-01-01

    NASA Glenn has constructed an airborne Ku-band satellite terminal, which provides wideband full-duplex ground-aircraft communications. The terminal makes use of novel electronically-steered phased array antennas and provides IP connectivity to and from the ground. The satcom terminal communications equipment may be easily changed whenever a new configuration is required, enhancing the terminal's versatility.

  19. Toolsets for Airborne Data Beta Release

    Atmospheric Science Data Center

    2014-09-17

    ... for Airborne Data (TAD), developed at the Atmospheric Science Data Center (ASDC) at NASA Langley Research Center (LaRC) to promote ... and Houston, and DC3 will be added shortly. Early next year we plan to add DISCOVER-AQ Colorado and SEAC4RS to the TAD database. We ...

  20. Mapping Waterhyacinth Infestations Using Airborne Hyperspectral Imagery

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Waterhyacinth [Eichhornia crassipes (Mart.) Solms] is an exotic aquatic weed that often invades and clogs waterways in many tropical and subtropical regions of the world. The objective of this study was to evaluate airborne hyperspectral imagery and different image classification techniques for mapp...

  1. A Technique for Airborne Aerobiological Sampling

    ERIC Educational Resources Information Center

    Mill, R. A.; And Others

    1972-01-01

    Report of a study of airborne micro-organisms collected over the Oklahoma City Metropolitan area and immediate environments, to investigate the possibility that a cloud of such organisms might account for the prevalence of some respiratory diseases in and around urban areas. (LK)

  2. Simulation system of airborne FLIR searcher

    NASA Astrophysics Data System (ADS)

    Sun, Kefeng; Li, Yu; Gao, Jiaobo; Wang, Jun; Wang, Jilong; Xie, Junhu; Ding, Na; Sun, Dandan

    2014-11-01

    Airborne Forward looking infra-red (FLIR) searcher simulation system can provide multi-mode simulated test environment that almost actual field environment, and can simulate integrated performance and external interface of airborne FLIR simulation system. Furthermore, the airborne FLIR searcher simulation system can support the algorithm optimization of image processing, and support the test and evaluation of electro-optical system, and also support the line test of software and evaluate the performance of the avionics system. The detailed design structure and information cross-linking relationship of each component are given in this paper. The simulation system is composed of the simulation center, the FLIR actuator, the FLIR emulator, and the display control terminal. The simulation center can generate the simulated target and aircraft flying data in the operation state of the airborne FLIR Searcher. The FLIR actuator can provide simulation scene. It can generate the infrared target and landform based scanning scene, response to the commands from simulation center and the FLIR actuator and operation control unit. The infrared image generated by the FLIR actuator can be processed by the FLIR emulator using PowerPC hardware framework and processing software based on VxWorks system. It can detect multi-target and output the DVI video and the multi-target detection information which corresponds to the working state of the FLIR searcher. Display control terminal can display the multi-target detection information in two-dimension situation format, and realize human-computer interaction function.

  3. Airborne hyperspectral detection of small changes.

    PubMed

    Eismann, Michael T; Meola, Joseph; Stocker, Alan D; Beaven, Scott G; Schaum, Alan P

    2008-10-01

    Hyperspectral change detection offers a promising approach to detect objects and features of remotely sensed areas that are too difficult to find in single images, such as slight changes in land cover and the insertion, deletion, or movement of small objects, by exploiting subtle differences in the imagery over time. Methods for performing such change detection, however, must effectively maintain invariance to typically larger image-to-image changes in illumination and environmental conditions, as well as misregistration and viewing differences between image observations, while remaining sensitive to small differences in scene content. Previous research has established predictive algorithms to overcome such natural changes between images, and these approaches have recently been extended to deal with space-varying changes. The challenges to effective change detection, however, are often exacerbated in an airborne imaging geometry because of the limitations in control over flight conditions and geometry, and some of the recent change detection algorithms have not been demonstrated in an airborne setting. We describe the airborne implementation and relative performance of such methods. We specifically attempt to characterize the effects of spatial misregistration on change detection performance, the efficacy of class-conditional predictors in an airborne setting, and extensions to the change detection approach, including physically motivated shadow transition classifiers and matched change filtering based on in-scene atmospheric normalization. PMID:18830283

  4. Tropospheric Emission Spectrometer and Airborne Emission Spectrometer

    NASA Technical Reports Server (NTRS)

    Glavich, T.; Beer, R.

    1996-01-01

    The Tropospheric Emission Spectrometer (TES) is an instrument being developed for the NASA Earth Observing System Chemistry Platform. TES will measure the distribution of ozone and its precursors in the lower atmosphere. The Airborne Emission Spectrometer (AES) is an aircraft precursor to TES. Applicable descriptions are given of instrument design, technology challenges, implementation and operations for both.

  5. Toolsets for Airborne Data Beta Release

    Atmospheric Science Data Center

    2014-09-17

    ... use, is now available. This beta-release is an intuitive user interface for variable selection across different airborne field studies ... we plan to add DISCOVER-AQ Colorado and SEAC4RS to the TAD database. We are currently focused on the in situ measurements and we want to ...

  6. Materiel requirements for airborne minefield detection system

    NASA Astrophysics Data System (ADS)

    Bertsche, Karl A.; Huegle, Helmut

    1997-07-01

    Within the concept study, Material Requirements for an airborne minefield detection systems (AMiDS) the following topics were investigated: (i) concept concerning airborne minefield detection technique sand equipment, (ii) verification analysis of the AMiDS requirements using simulation models and (iii) application concept of AMiDS with regard o tactics and military operations. In a first approach the problems concerning unmanned airborne minefield detection techniques within a well-defined area were considered. The complexity of unmanned airborne minefield detection is a result of the following parameters: mine types, mine deployment methods, tactical requirements, topography, weather conditions, and the size of the area to be searched. In order to perform the analysis, a simulation model was developed to analyze the usability of the proposed remote controlled air carriers. The basic flight patterns for the proposed air carriers, as well as the preparation efforts of military operations and benefits of such a system during combat support missions were investigated. The results of the conceptual study showed that a proposed remote controlled helicopter drone could meet the stated German MOD scanning requirements of mine barriers. Fixed wing air carriers were at a definite disadvantage because of their inherently large turning loops. By implementing a mine detection system like AMiDS minefields can be reconnoitered before an attack. It is therefore possible either to plan, how the minefields can be circumvented or where precisely breaching lanes through the mine barriers are to be cleared for the advancing force.

  7. Airborne UV Lidar for Forest Parameter Retrievals

    NASA Astrophysics Data System (ADS)

    Shang, Xiaoxia; Chazette, Patrick; Totems, Julien

    2016-06-01

    A full-waveform UV lidar performed airborne measurements over several temperate and tropical forests sites. The structural and ecological parameters (canopy height, quadratic mean canopy height and apparent foliage) were extracted from lidar backscattered profiles. The aboveground carbon and leaf area index are also evaluated from lidar measurements.

  8. Repeatability Using Automatic Tracing with Canon OCT- HS100 and Zeiss Cirrus HD-OCT 5000

    PubMed Central

    Brautaset, Rune; Birkeldh, Ulrika; Frehr Alstig, Petra; Wikén, Petra; Nilsson, Maria

    2016-01-01

    Background Optical coherence tomography (OCT), can be used in clinical practice to provide high resolution cross-sectional images of the retina, optic disc and macula structure. These measurements can be useful for early detection, diagnosis, monitoring and treatment guidance for retinal diseases. Therefore, repeatability of measurements in OCT is of great importance. Methods Macula and optic disc parameters from the right eye of 30 healthy subjects were obtained twice with the Canon OCT-HS100 and Zeiss Cirrus HD-OCT 5000. Repeatability was evaluated by use of the coefficient of repeatability (CR) and the coefficient of repeatability as a percentage of the mean (CR%), and the obtained measurements were compared between the instruments. Results CR% of optic disc parameters ranged between 0.90 and 22.22% and 0.00 and 16.00% with the Canon and Zeiss OCT respectively. For macular parameters CR% ranged between 0.62 and 2.81% and 0.99 and 1.81% with the Canon and Zeiss OCT respectively. No statistical difference could be found when comparing the CR of all macular and disc measurements between the instruments. Compared to our previously published data repeatability has significantly improved with the inclusion of automatic tracking systems with both the Canon and Zeiss OCT. Conclusion Automatic tracking function improves repeatability in both Canon OCT-HS100 and Zeiss Cirrus HD-OCT 5000. However, measurements generated by the two instruments are still not interchangeable. PMID:26867021

  9. Flight test evaluation of a video tracker for enhanced offshore airborne radar approach capability

    NASA Technical Reports Server (NTRS)

    Clary, G. R.; Cooper, P. G.

    1982-01-01

    As a part of NASA's Rotorcraft All-Weather Operations Research Program, advanced airborne radar approach (ARA) concepts are being investigated. Since data from previous NASA/FAA flight tests showed significant ARA limitations, a research program was initiated at NASA Ames Research Center to determine the benefit that could be derived by automating certain radar functions and superimposing course display data on the radar display. To evaluate these concepts, a newly developed video tracking system which interfaces with weather radar was acquired. After the pilot designates a destination target, the system tracks the target video as it moves on the radar indicator. Using a small, efficient microprocessor, the autotracker presents valuable approach data on the radar screen and automatically adjusts the radar gain and tilt. Results of a limited flight test evaluation of the autotracker show that the course display concept, combined with automated gain and tilt functions, is effective for improving ARA's and reducing radar operator workload.

  10. A digital elevation model of the Greenland ice sheet and validation with airborne laser altimeter data

    NASA Technical Reports Server (NTRS)

    Bamber, Jonathan L.; Ekholm, Simon; Krabill, William B.

    1997-01-01

    A 2.5 km resolution digital elevation model (DEM) of the Greenland ice sheet was produced from the 336 days of the geodetic phase of ERS-1. During this period the altimeter was operating in ice-mode over land surfaces providing improved tracking around the margins of the ice sheet. Combined with the high density of tracks during the geodetic phase, a unique data set was available for deriving a DEM of the whole ice sheet. The errors present in the altimeter data were investigated via a comparison with airborne laser altimeter data obtained for the southern half of Greenland. Comparison with coincident satellite data showed a correlation with surface slope. An explanation for the behavior of the bias as a function of surface slope is given in terms of the pattern of surface roughness on the ice sheet.

  11. 47 CFR 22.1015 - Repeater operation.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 47 Telecommunication 2 2010-10-01 2010-10-01 false Repeater operation. 22.1015 Section 22.1015 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) COMMON CARRIER SERVICES PUBLIC MOBILE SERVICES Offshore Radiotelephone Service § 22.1015 Repeater operation. Offshore central stations may be used as repeater stations provided that...

  12. Repeated Reading. What Works Clearinghouse Intervention Report

    ERIC Educational Resources Information Center

    What Works Clearinghouse, 2014

    2014-01-01

    "Repeated reading" is an academic practice that aims to increase oral reading fluency. "Repeated reading" can be used with students who have developed initial word reading skills but demonstrate inadequate reading fluency for their grade level. During "repeated reading," a student sits in a quiet location with a…

  13. Infrared airborne spectroradiometer survey results in the western Nevada area

    NASA Technical Reports Server (NTRS)

    Collins, W.; Chang, S. H.; Kuo, J. T.

    1982-01-01

    The Mark II airborne spectroradiometer system was flown over several geologic test sites in western Nevada. The infrared mineral absorption bands were observed and recorded for the first time using an airborne system with high spectral resolution in the 2.0 to 2.5 micron region. The data show that the hydrothermal alteration zone minerals, carbonates, and other minerals are clearly visible in the airborne survey mode. The finer spectral features that distinguish the various minerals with infrared bands are also clearly visible in the airborne survey data. Using specialized computer pattern recognition methods, it is possible to identify mineralogy and map alteration zones and lithologies by airborne spectroradiometer survey techniques.

  14. CALIOPE airborne CO{sub 2} DIAL (CACDI) system design

    SciTech Connect

    Mietz, D.; Archuleta, B.; Archuleta, J.

    1997-09-01

    Los Alamos National Laboratory is currently developing an airborne CO{sub 2} Differential Absorption Lidar (DIAL) system based on second generation technology demonstrated last summer at NTS. The CALIOPE Airborne CO{sub 2} DIAL (CACDI) system requirements have been compiled based on the mission objectives and SONDIAL model trade studies. Subsystem designs have been developed based on flow down from these system requirements, as well as experience gained from second generation ground tests and N-ABLE (Non-proliferation AirBorne Lidar Experiments) airborne experiments. This paper presents the CACDI mission objectives, system requirements, the current subsystem design, and provides an overview of the airborne experimental plan.

  15. Introduction to an airborne remote sensing system equipped onboard the Chinese marine surveillance plane

    NASA Astrophysics Data System (ADS)

    Gong, Fang; Wang, Difeng; Pan, Delu; Hao, Zengzhou

    2008-10-01

    The airborne remote sensing system onboard the Chinese Marine Surveillance Plane have three scanners including marine airborne multi-spectrum scanner(MAMS), airborne hyper spectral system(AISA+) and optical-electric platform(MOP) currently. MAMS is developed by Shanghai Institute of Technology and Physics CAS with 11 bands from ultraviolet to infrared and mainly used for inversion of oceanic main factors and pollution information, like chlorophyll, sea surface temperature, red tide, etc. The AISA+ made by Finnish Specim company is a push broom system, consist of a high spectrum scanner head, a miniature GPS/INS sensor and data collecting PC. It is a kind of aviation imaging spectrometer and has the ability of ground target imaging and measuring target spectrum characteristic. The MOP mainly supports for object watching, recording and track. It mainly includes 3 equipments: digital CCD with Sony-DXC390, CANON EOS film camera and digital camera Sony F717. This paper mainly introduces these three remote sensing instruments as well as the ground processing information system, involving the system's hardware and software design, related algorithm research, etc.

  16. Flight investigation of helicopter IFR approaches to oil rigs using airborne weather and mapping radar

    NASA Technical Reports Server (NTRS)

    Bull, J. S.; Hegarty, D. M.; Phillips, J. D.; Sturgeon, W. R.; Hunting, A. W.; Pate, D. P.

    1979-01-01

    Airborne weather and mapping radar is a near-term, economical method of providing 'self-contained' navigation information for approaches to offshore oil rigs and its use has been rapidly expanding in recent years. A joint NASA/FAA flight test investigation of helicopter IFR approaches to offshore oil rigs in the Gulf of Mexico was initiated in June 1978 and conducted under contract to Air Logistics. Approximately 120 approaches were flown in a Bell 212 helicopter by 15 operational pilots during the months of August and September 1978. The purpose of the tests was to collect data to (1) support development of advanced radar flight director concepts by NASA and (2) aid the establishment of Terminal Instrument Procedures (TERPS) criteria by the FAA. The flight test objectives were to develop airborne radar approach procedures, measure tracking errors, determine accpetable weather minimums, and determine pilot acceptability. Data obtained will contribute significantly to improved helicopter airborne radar approach capability and to the support of exploration, development, and utilization of the Nation's offshore oil supplies.

  17. Airborne Hyperspectral Infrared Imaging Survey of the Southern San Andreas Fault

    NASA Astrophysics Data System (ADS)

    Lynch, D. K.; Tratt, D. M.; Buckland, K. N.; Johnson, P. D.

    2014-12-01

    The San Andreas Fault (SAF) between Desert Hot Springs and Bombay Beach has been surveyed with Mako, an airborne hyperspectral imager operating across the wavelength range 7.6-13.2 μm in the thermal-infrared (TIR) spectral region. The data were acquired with a 4-km swath width centered on the SAF, and many tectonic features are recorded in the imagery. Spectral analysis using diagnostic features of minerals can identify rocks, soils and vegetation. Mako imagery can also locate rupture zones and measure slip distances. Designed and built by The Aerospace Corporation, the innovative and highly capable airborne imaging spectrometer used for this work enables low-noise performance (NEΔT ≲ 0.1 K @ 10 μm) at small pixel IFOV (0.55 mrad) and high frame rates, making possible an area-coverage rate of 20 km2 per minute with 2-m ground resolution from 12,500 ft (3.8 km) above-ground altitude. Since its commissioning in 2010, Mako has been used in numerous studies involving other earthquake fault systems (Hector Mine, S. Bristol Mts.), mapping of surface geology, geothermal sources (fumaroles near the Salton Sea), urban surveys, and the detection, quantification, and tracking of natural and anthropogenic gaseous emission plumes. Mako is available for airborne field studies and new applications are of particular interest. It can be flown at any altitude below 20,000 ft to achieve the desired GSD.

  18. Ground testing and campaign intercomparisons with the NAST-I airborne FTS

    NASA Astrophysics Data System (ADS)

    Larar, Allen M.; Zhou, Daniel K.; Liu, Xu; Smith, William L.; Rochette, Luc; Noe, Anna; Oliver, Don; Tian, Jialin

    2014-10-01

    The NASA / JPSS Airborne Sounder Testbed - Interferometer (NAST-I) is a well-proven airborne remote sensing system, which has flown in 19 previous field campaigns aboard the high altitude NASA ER-2, Northrop Grumman / Scaled Composites Proteus, and NASA WB-57 aircraft since initially being flight qualified in 1998. While originally developed to provide experimental observations needed to finalize specifications and test proposed designs and data processing algorithms for the Cross-track Infrared Sounder (CrIS) flying aboard the Suomi National Polar-orbiting Operational Environmental Satellite System (NPOESS) Preparatory Project (SNPP) and the Joint Polar Satellite System, JPSS (formerly NPOESS, prior to program restructuring), its unprecedented data quality and system characteristics have contributed to a variety of atmospheric research and measurement validation objectives. This paper will provide a program overview and update, including a summary of measurement system capabilities, with a primary focus on postmission ground testing and characterization performed subsequent to the recently conducted Suomi NPP (SNPP) airborne field campaign.

  19. Tomographic Imaging of a Forested Area By Airborne Multi-Baseline P-Band SAR

    PubMed Central

    Frey, Othmar; Morsdorf, Felix; Meier, Erich

    2008-01-01

    In recent years, various attempts have been undertaken to obtain information about the structure of forested areas from multi-baseline synthetic aperture radar data. Tomographic processing of such data has been demonstrated for airborne L-band data but the quality of the focused tomographic images is limited by several factors. In particular, the common Fourier-based focusing methods are susceptible to irregular and sparse sampling, two problems, that are unavoidable in case of multi-pass, multi-baseline SAR data acquired by an airborne system. In this paper, a tomographic focusing method based on the time-domain back-projection algorithm is proposed, which maintains the geometric relationship between the original sensor positions and the imaged target and is therefore able to cope with irregular sampling without introducing any approximations with respect to the geometry. The tomographic focusing quality is assessed by analysing the impulse response of simulated point targets and an in-scene corner reflector. And, in particular, several tomographic slices of a volume representing a forested area are given. The respective P-band tomographic data set consisting of eleven flight tracks has been acquired by the airborne E-SAR sensor of the German Aerospace Center (DLR).

  20. Spectral combination of land-based, airborne, shipborne and altimeter-derived gravity values: examples in Taiwan and Tahiti

    NASA Astrophysics Data System (ADS)

    Hwang, Cheinway

    2016-04-01

    Taiwan and Tahiti are bordered by seas and are islands with mountain ranges up to 4000 m height. The gravity fields here are rough due to the geodynamic processes that create the islands. On and around the two islands, gravity data have been collected by land gravimeters in relative gravity networks (point-wise), by airborne and shipborne (along-track) methods and by transformations from sea surface heights (altimeter-derived). Typically, network-adjusted land gravity values have accuracies of few tens of micro gals and contain the full gravity spectrum. Airborne gravity values are obtained by filtering original one-HZ along-track gravity values collected at varying flight altitudes that are affected by aircraft dynamics, GPS positioning error and gravimeter error. At a 5000-m flight height, along-track airborne gravity has a typical spatial resolution of 4 km and an accuracy of few mgal. Shipborne gravity is similar to airborne gravity, but with higher spatial resolutions because of ship's lower speed. Altimeter-derived gravity has varying spatial resolutions and accuracies, depending on altimeter data, processing method and extent of waveform interference. Using the latest versions of Geosat/GM, ERS-1/GM, ENVISAT, Jason-1/GM, Cryosat-2 and SARAL altimeter data, one can achieve accuracies at few mgal. The synergy of the four kinds of gravity datasets is made by the band-limited least-squares collocation, which best integrates datasets of different accuracies and spatial resolutions. The method uses the best contributions from a DEM, a global gravity model, available gravity datasets to form an optimal gravity grid. We experiment with different optimal spherical harmonic degrees of EGM08 for use around the two islands. For Tahiti, the optimal degree is 1500. New high-resolution gravity and geoid grids are constructed for the two islands and can be used in future geophysical and geodetic studies.

  1. Orientation of Airborne Laser Scanning Point Clouds with Multi-View, Multi-Scale Image Blocks

    PubMed Central

    Rönnholm, Petri; Hyyppä, Hannu; Hyyppä, Juha; Haggrén, Henrik

    2009-01-01

    Comprehensive 3D modeling of our environment requires integration of terrestrial and airborne data, which is collected, preferably, using laser scanning and photogrammetric methods. However, integration of these multi-source data requires accurate relative orientations. In this article, two methods for solving relative orientation problems are presented. The first method includes registration by minimizing the distances between of an airborne laser point cloud and a 3D model. The 3D model was derived from photogrammetric measurements and terrestrial laser scanning points. The first method was used as a reference and for validation. Having completed registration in the object space, the relative orientation between images and laser point cloud is known. The second method utilizes an interactive orientation method between a multi-scale image block and a laser point cloud. The multi-scale image block includes both aerial and terrestrial images. Experiments with the multi-scale image block revealed that the accuracy of a relative orientation increased when more images were included in the block. The orientations of the first and second methods were compared. The comparison showed that correct rotations were the most difficult to detect accurately by using the interactive method. Because the interactive method forces laser scanning data to fit with the images, inaccurate rotations cause corresponding shifts to image positions. However, in a test case, in which the orientation differences included only shifts, the interactive method could solve the relative orientation of an aerial image and airborne laser scanning data repeatedly within a couple of centimeters. PMID:22454569

  2. A Flight Test of the Strapdown Airborne Gravimeter SGA-WZ in Greenland

    PubMed Central

    Zhao, Lei; Forsberg, René; Wu, Meiping; Olesen, Arne Vestergaard; Zhang, Kaidong; Cao, Juliang

    2015-01-01

    An airborne gravimeter is one of the most important tools for gravity data collection over large areas with mGal accuracy and a spatial resolution of several kilometers. In August 2012, a flight test was carried out to determine the feasibility and to assess the accuracy of the new Chinese SGA-WZ strapdown airborne gravimeter in Greenland, in an area with good gravity coverage from earlier marine and airborne surveys. An overview of this new system SGA-WZ is given, including system design, sensor performance and data processing. The processing of the SGA-WZ includes a 160 s length finite impulse response filter, corresponding to a spatial resolution of 6 km. For the primary repeated line, a mean r.m.s. deviation of the differences was less than 1.5 mGal, with the error estimate confirmed from ground truth data. This implies that the SGA-WZ could meet standard geophysical survey requirements at the 1 mGal level. PMID:26057039

  3. A Flight Test of the Strapdown Airborne Gravimeter SGA-WZ in Greenland.

    PubMed

    Zhao, Lei; Forsberg, René; Wu, Meiping; Olesen, Arne Vestergaard; Zhang, Kaidong; Cao, Juliang

    2015-01-01

    An airborne gravimeter is one of the most important tools for gravity data collection over large areas with mGal accuracy and a spatial resolution of several kilometers. In August 2012, a flight test was carried out to determine the feasibility and to assess the accuracy of the new Chinese SGA-WZ strapdown airborne gravimeter in Greenland, in an area with good gravity coverage from earlier marine and airborne surveys. An overview of this new system SGA-WZ is given, including system design, sensor performance and data processing. The processing of the SGA-WZ includes a 160 s length finite impulse response filter, corresponding to a spatial resolution of 6 km. For the primary repeated line, a mean r.m.s. deviation of the differences was less than 1.5 mGal, with the error estimate confirmed from ground truth data. This implies that the SGA-WZ could meet standard geophysical survey requirements at the 1 mGal level. PMID:26057039

  4. Leveraging Realtime Data in Airborne Campaigns: From COMEX to Disaster Response

    NASA Astrophysics Data System (ADS)

    Leifer, I.; Thompson, D. R.; Bovensmann, H.; Eastwood, M. L.; Fladeland, M. M.; Gerilowski, K.; Green, R. O.; Krautwurst, S.; Krings, T.; Luna, B.; Di Benedetto, J.; Morey, M.

    2015-12-01

    The COMEX (CO2 and Methane eXperiment) campaign leveraged real-time remote sensing and in situ data spanning multiple airborne and surface mobile platforms and interplatform communications to improve dramatically science outcomes. COMEX realtime remote sensing of strong methane plumes released from a producing oil field in Southern California by the non-imaging spectrometer MAMAP (Methane Airborne MAPper) were used to shift the survey strategy of the AVIRIS NG (Airborne Visual InfraRed Imaging Spectrometer-Next Generation) instrument on a separate airplane from an area of few plumes to an area of high activity. Concurrently, a ground team was re-directed to collect mobile surface validation data by the AMOG (AutoMObile gas) Surveyor in the new area. On all platforms, realtime analysis were used to adapt the survey patterns such as making tactical decisions to repeat certain swaths or flight lines by AVIRIS NG and by MAMAP and to adapt surface survey patterns. The AVIRIS-NG realtime algorithms were developed for methane; however, oil exhibits spectral features that are similar, enabling their testing on AVIRIS-NG data acquired during the Santa Barbara Oil Spill. The effort determined that realtime oil mapping currently is feasible. For oil spill disaster response as well as other disaster response applications, the tactical advantages of realtime remote sensing for time-critical data collections will facilitate greater roles played by remote sensing in future disaster response.

  5. Airborne laser sensors and integrated systems

    NASA Astrophysics Data System (ADS)

    Sabatini, Roberto; Richardson, Mark A.; Gardi, Alessandro; Ramasamy, Subramanian

    2015-11-01

    The underlying principles and technologies enabling the design and operation of airborne laser sensors are introduced and a detailed review of state-of-the-art avionic systems for civil and military applications is presented. Airborne lasers including Light Detection and Ranging (LIDAR), Laser Range Finders (LRF), and Laser Weapon Systems (LWS) are extensively used today and new promising technologies are being explored. Most laser systems are active devices that operate in a manner very similar to microwave radars but at much higher frequencies (e.g., LIDAR and LRF). Other devices (e.g., laser target designators and beam-riders) are used to precisely direct Laser Guided Weapons (LGW) against ground targets. The integration of both functions is often encountered in modern military avionics navigation-attack systems. The beneficial effects of airborne lasers including the use of smaller components and remarkable angular resolution have resulted in a host of manned and unmanned aircraft applications. On the other hand, laser sensors performance are much more sensitive to the vagaries of the atmosphere and are thus generally restricted to shorter ranges than microwave systems. Hence it is of paramount importance to analyse the performance of laser sensors and systems in various weather and environmental conditions. Additionally, it is important to define airborne laser safety criteria, since several systems currently in service operate in the near infrared with considerable risk for the naked human eye. Therefore, appropriate methods for predicting and evaluating the performance of infrared laser sensors/systems are presented, taking into account laser safety issues. For aircraft experimental activities with laser systems, it is essential to define test requirements taking into account the specific conditions for operational employment of the systems in the intended scenarios and to verify the performance in realistic environments at the test ranges. To support the

  6. Wind Retrieval Algorithms for the IWRAP and HIWRAP Airborne Doppler Radars with Applications to Hurricanes

    NASA Technical Reports Server (NTRS)

    Guimond, Stephen Richard; Tian, Lin; Heymsfield, Gerald M.; Frasier, Stephen J.

    2013-01-01

    Algorithms for the retrieval of atmospheric winds in precipitating systems from downward-pointing, conically-scanning airborne Doppler radars are presented. The focus in the paper is on two radars: the Imaging Wind and Rain Airborne Profiler(IWRAP) and the High-altitude IWRAP (HIWRAP). The IWRAP is a dual-frequency (Cand Ku band), multi-beam (incidence angles of 30 50) system that flies on the NOAAWP-3D aircraft at altitudes of 2-4 km. The HIWRAP is a dual-frequency (Ku and Kaband), dual-beam (incidence angles of 30 and 40) system that flies on the NASA Global Hawk aircraft at altitudes of 18-20 km. Retrievals of the three Cartesian wind components over the entire radar sampling volume are described, which can be determined using either a traditional least squares or variational solution procedure. The random errors in the retrievals are evaluated using both an error propagation analysis and a numerical simulation of a hurricane. These analyses show that the vertical and along-track wind errors have strong across-track dependence with values of 0.25 m s-1 at nadir to 2.0 m s-1 and 1.0 m s-1 at the swath edges, respectively. The across-track wind errors also have across-track structure and are on average, 3.0 3.5 m s-1 or 10 of the hurricane wind speed. For typical rotated figure four flight patterns through hurricanes, the zonal and meridional wind speed errors are 2 3 m s-1.Examples of measured data retrievals from IWRAP during an eyewall replacement cycle in Hurricane Isabel (2003) and from HIWRAP during the development of Tropical Storm Matthew (2010) are shown.

  7. The Beginnings of Airborne Astronomy, 1920 - 1930: an Historical Narrative

    NASA Technical Reports Server (NTRS)

    Craine, E. R.

    1984-01-01

    The emergence of airborne astronomy in the early twentieth century is recounted. The aerial expedition to observe the solar eclipse on September 10, 1923, is described. Observation of the total solar eclipse of January 24, 1925, is discussed. The Honey Lake aerial expedition to study the solar eclipse of April 28, 1930, is also described. Four major accomplishments in airborne astronomy during the period 1920 to 1930 are listed. Airborne expeditions were undertaken at every logical opportunity, starting a continuous sequence of airborne astronomical expeditions which was to remain unbroken, except by World War II, to the present day. Although the scientific returns of the first ten years were modest, they did exist. Interest in, and support for, airborne astronomy was generated not only among astronomers but also among the public. Albert Stevens, arguably the true father of airborne astronomy, was to become interested in applying his considerable skill and experience to the airborne acquisition of astronomical data.

  8. Extrapolating target tracks

    NASA Astrophysics Data System (ADS)

    Van Zandt, James R.

    2012-05-01

    Steady-state performance of a tracking filter is traditionally evaluated immediately after a track update. However, there is commonly a further delay (e.g., processing and communications latency) before the tracks can actually be used. We analyze the accuracy of extrapolated target tracks for four tracking filters: Kalman filter with the Singer maneuver model and worst-case correlation time, with piecewise constant white acceleration, and with continuous white acceleration, and the reduced state filter proposed by Mookerjee and Reifler.1, 2 Performance evaluation of a tracking filter is significantly simplified by appropriate normalization. For the Kalman filter with the Singer maneuver model, the steady-state RMS error immediately after an update depends on only two dimensionless parameters.3 By assuming a worst case value of target acceleration correlation time, we reduce this to a single parameter without significantly changing the filter performance (within a few percent for air tracking).4 With this simplification, we find for all four filters that the RMS errors for the extrapolated state are functions of only two dimensionless parameters. We provide simple analytic approximations in each case.

  9. Linear Synchronous Motor Repeatability Tests

    SciTech Connect

    Ward, C.R.

    2002-10-18

    A cart system using linear synchronous motors was being considered for the Plutonium Immobilization Plant (PIP). One of the applications in the PIP was the movement of a stack of furnace trays, filled with the waste form (pucks) from a stacking/unstacking station to several bottom loaded furnaces. A system was ordered to perform this function in the PIP Ceramic Prototype Test Facility (CPTF). This system was installed and started up in SRTC prior to being installed in the CPTF. The PIP was suspended and then canceled after the linear synchronous motor system was started up. This system was used to determine repeatability of a linear synchronous motor cart system for the Modern Pit Facility.

  10. Multiple Human Tracking Using Binary Infrared Sensors.

    PubMed

    Miyazaki, Toshiaki; Kasama, Yuki

    2015-01-01

    To create a context-aware environment, human locations and movement paths must be considered. In this paper, we propose an algorithm that tracks human movement paths using only binary sensed data obtained by infrared (IR) sensors attached to the ceiling of a room. Our algorithm can estimate multiple human movement paths without a priori knowledge of the number of humans in the room. By repeating predictions and estimations of human positions and links from the previous human positions to the estimated ones at each time period, human movement paths can be estimated. Simulation-based evaluation results show that our algorithm can dynamically trace human movement paths. PMID:26061201

  11. Multiple Human Tracking Using Binary Infrared Sensors

    PubMed Central

    Miyazaki, Toshiaki; Kasama, Yuki

    2015-01-01

    To create a context-aware environment, human locations and movement paths must be considered. In this paper, we propose an algorithm that tracks human movement paths using only binary sensed data obtained by infrared (IR) sensors attached to the ceiling of a room. Our algorithm can estimate multiple human movement paths without a priori knowledge of the number of humans in the room. By repeating predictions and estimations of human positions and links from the previous human positions to the estimated ones at each time period, human movement paths can be estimated. Simulation-based evaluation results show that our algorithm can dynamically trace human movement paths. PMID:26061201

  12. Association ambiguity management in mixed data dimension tracking problems

    NASA Astrophysics Data System (ADS)

    Thornbrue, James R.; Knight, J. Nate; Slocumb, Benjamin J.

    2010-04-01

    Association and fusion of passive direction finding (DF) reports with active radar tracks from airborne targets is challenging because of the low dimensionality of the common kinematic measurement space. Often, multi-target scenarios lead to significant data association ambiguity. Classically, the approach to this problem is a simple hypothesis test wherein a batch of DF sensor measurements is associated with either zero or one of the radar tracks; assignment of multiple DF tracks to a single radar track is allowed without regard to compatibility, and this can lead to detrimental results. This paper develops a new approach for managing the ambiguity. The problem is formulated as a two-dimensional assignment, and any association ambiguity is determined from the k best solutions. Firm association decisions are made only when the ambiguity is at an acceptable level. The ambiguity information is also available in real time as an output to the system operator. An improved batch association score, relative to previous works, is formulated that addresses statistical correlations between individual measurement-to-track residuals; this new score is a likelihood ratio generated from Kalman Filter residuals. Where previous scoring methods lead to incorrect ambiguity assessments in certain scenarios, the new approach yields accurate results. Because the score is recursive, the batch may be extended over an arbitrary number of measurements, helping to manage association ambiguities over time. Simulation results are shown to demonstrate the algorithm.

  13. Optimal structural design of the Airborne Infrared Imager

    NASA Astrophysics Data System (ADS)

    Doyle, Keith B.; Cerrati, Vincent J.; Forman, Steven E.; Sultana, John A.

    1995-09-01

    The airborne infrared imager (AIRI) is a dual-band IR sensor designed to study air defense issues while wing mounted in a pod. The sensor consists of an optical bench attached to a two- axis inertially stabilized gimbal structure in elevation and azimuth. The gimbal assembly operates within an 18-inch diameter globe while meeting strict pointing and tracking requirements. Design conditions for the assembly include operational and nonoperational inertial, thermal, and dynamic loads. Primary design efforts centered on limiting the line-of- sight jitter of the optical system to 50 (mu) rad under the operating environment. An MSC/NASTRAN finite element model was developed for structural response predictions and correlated to experimental data. Design changes were aided by MSC/NASTRAN's optimization routine with the goal of maximizing the fundamental frequency of the gimbal assembly. The final structural design resultsed in a first natural frequency of 79 Hz using a titanium azimuthal gimbal, a stainless steel elevation gimbal, and an aluminum optical bench which met the design and performance requirements.

  14. Airborne target identification from low-crossrange-resolution ISAR imagery

    NASA Astrophysics Data System (ADS)

    Hauss, Bruce I.; Agravante, Hiroshi H.; Eberhard, C. D.; Luebkemann, Karen M.; Samec, Thomas K.; Wagner, Thomas M.; Rihaczek, August W.; Hershkowitz, Stephen J.; Mitchell, R. L.; Perahia, E.; Arnush, Donald; Lakshmanan, Sridhar

    1996-11-01

    In a target-rich battlefield environment, a shipboard or an airborne radar must maintain situational awareness while tracking and identifying targets. Often the opportunity to dwell on each target long enough for confident identification via high resolution SAR/ISAR imaging will not exist, especially for those engagement geometries where the relative translational motion of the aircraft does not result in large rotation rates. Inadvertent aircraft tactical dither often generates enough target rotational during a brief imaging interval to allow the formation of an ISAR image with low crossrange resolution. We have developed an automated identification procedure that utilizes this resolution, along with high range resolution, to produce confident target identification. The advanced signal processing algorithms employed extract feature measurements from the complex ISAR image. including accurate measurements of the two-dimensional positions, amplitudes and range extents of the dominant target scatterers. A deformable template matching procedure is used to correlate these 'measured features' with those predicted for each candidate aircraft in a database generated from readily available diagrams, photographs and CAD models. After obtaining the optimal fit between the measured and predicted features for each candidate aircraft, the 'most likely' candidate is selected using a conventional Bayes classifier.

  15. Airborne Observations of Ammonia Emissions from North Carolina Swine Facilities

    NASA Astrophysics Data System (ADS)

    Nowak, J. B.; Neuman, J. A.; Liao, J.; Welti, A.; Middlebrook, A. M.; McKeen, S. A.; Trainer, M.; Parrish, D. D.

    2013-12-01

    Ammonia (NH3) is the dominant gas-phase base in the troposphere. As a consequence, NH3 abundance influences particle formation and composition. Anthropogenic emissions of NH3 can react with sulfuric acid (H2SO4) and nitric acid (HNO3), photochemical oxidation products of sulfur dioxide (SO2) and nitrogen oxides (NOx (NO + NO2)), to form ammoniated particles that typically account for half or more of measured PM2.5 mass in the Eastern US. NH3 emissions are predominantly from agricultural sources, primarily livestock animal waste and crop fertilization. Accurate NH3 emissions estimates from these sources are necessary for developing effective particle control strategies. Swine facilities in North Carolina are one of the largest source of NH3 emissions in the Southeastern US. Airborne measurements of NH3 and particulate ammonium (NH4+) made aboard the NOAA WP-3D aircraft as part of the recent 2013 SENEX field campaign are used to quantify NH3 emissions from North Carolina swine facilities. The observed NH3 emissions are compared to swine facility emissions estimates from current emissions inventories. In addition, the NH3 emissions from swine facilities are placed in the broader context of NH3 sources through comparison to recent emissions observations from dairy facilities in California. The July 10 SENEX WP-3D flight track colored and sized by observed NH3 mixing ratios.

  16. Comparison of TRMM Precipitation Radar and Airborne Radar Data.

    NASA Astrophysics Data System (ADS)

    Durden, S. L.; Im, E.; Haddad, Z. S.; Li, L.

    2003-06-01

    The first spaceborne weather radar is the precipitation radar (PR) on the Tropical Rainfall Measuring Mission (TRMM), which was launched in 1997. As part of the TRMM calibration and validation effort, an airborne rain-mapping radar (ARMAR) was used to make underflights of TRMM during the B portion of the Texas and Florida Underflights (TEFLUN-B) and the third Convection and Moisture Experiment (CAMEX-3) in 1998 and the Kwajalein Experiment (KWAJEX) in 1999. The TRMM PR and ARMAR both operate at 14 GHz, and both instruments use a downward-looking, cross-track scanning geometry, which allows direct comparison of data. Nearly simultaneous PR and ARMAR data were acquired in seven separate cases. These data are compared to examine the effects of larger resolution volume and lower sensitivity in the PR data relative to ARMAR. The PR and ARMAR data show similar structures, although the PR data tend to have lower maximum reflectivities and path attenuations because of nonuniform beam-filling effects. Nonuniform beam filling can also cause a bias in the observed path attenuation relative to that corresponding to the beam-averaged rain rate. The PR rain-type classification is usually consistent with the ARMAR data.

  17. FTIR-based airborne spectral imagery for target interrogation

    NASA Astrophysics Data System (ADS)

    Smithson, Tracy L.; St. Germain, Daniel; Nadeau, Denis

    2007-09-01

    DRDC Valcartier is continuing to developed infrared spectral imagery systems for a variety of military applications. Recently a hybrid airborne spectral imager / broadband imager system has been developed for ground target interrogation (AIRIS). This system employs a Fourier Transform Interferometer system coupled to two 8x8 element detector arrays to create spectral imagery in the region from 2.0 to 12 microns (830 to 5000 cm -1) at a spectral resolution of up to 1 cm -1. In addition, coupled to this sensor are three broadband imagers operating in the visible, mid-wave and long-wave infrared regions. AIRIS uses an on-board tracking capability to: dwell on a target, select multiple targets sequentially, or build a mosaic description of the environment around a specified target point. Currently AIRIS is being modified to include real-time spectral imagery calibration and application processing. In this paper the flexibility of the AIRIS system will be described, its concept of operation discussed and examples of measurements will be shown.

  18. The Airborne Laser Ranging System - Its capabilities and applications

    NASA Technical Reports Server (NTRS)

    Kahn, W. D.; Degnan, J. J.; Englar, T. S., Jr.

    1983-01-01

    The Airborne Laser Ranging System is a proposed multibeam short pulse laser ranging system on board an aircraft. It simultaneously measures the distances between the aircraft and six laser retroreflectors (targets) deployed on the earth's surface. Depending on the host aircraft and terrain characteristics, the system can interrogate hundreds of targets distributed over an area as large as 60,000 sq. km in a matter of hours. Potentially, a total of 1.3 million individual range measurements can be made in a 6 hr flight. The precision of these range measurements is approximately 1 cm. These measurements are then used in a procedure which is basically an extension of trilateration techniques to derive the intersite vector between the laser ground targets. By repeating the estimation of the intersite vector, strain and strain rate errors can be estimated. These quantities are essential for crustal dynamic studies which include determination and monitoring of regional strain in the vicinity of active fault zones, land subsidence, and edifice building preceding volcanic eruptions.

  19. Inversion of Airborne Contaminants in a Regional Model

    SciTech Connect

    Akcelik, V.; Biros, G.; Draganescu, A.; Ghattas, O.; Hill, J.; van Bloemen Waanders, B.; /SLAC /Pennsylvania U. /Texas U. /Sandia

    2007-01-10

    We are interested in a DDDAS problem of localization of airborne contaminant releases in regional atmospheric transport models from sparse observations. Given measurements of the contaminant over an observation window at a small number of points in space, and a velocity field as predicted for example by a mesoscopic weather model, we seek an estimate of the state of the contaminant at the beginning of the observation interval that minimizes the least squares misfit between measured and predicted contaminant field, subject to the convection-diffusion equation for the contaminant. Once the ''initial'' conditions are estimated by solution of the inverse problem, we issue predictions of the evolution of the contaminant, the observation window is advanced in time, and the process repeated to issue a new prediction, in the style of 4D-Var. We design an appropriate numerical strategy that exploits the spectral structure of the inverse operator, and leads to efficient and accurate resolution of the inverse problem. Numerical experiments verify that high resolution inversion can be carried out rapidly for a well-resolved terrain model of the greater Los Angeles area.

  20. Identifying Colluvial Slopes by Airborne LiDAR Analysis

    NASA Astrophysics Data System (ADS)

    Kasai, M.; Marutani, T.; Yoshida, H.

    2015-12-01

    Colluvial slopes are one of major sources of landslides. Identifying the locations of the slopes will help reduce the risk of disasters, by avoiding building infrastructure and properties nearby, or if they are already there, by applying appropriate counter measures before it suddenly moves. In this study, airborne LiDAR data was analyzed to find their geomorphic characteristics to use for extracting their locations. The study site was set in the suburb of Sapporo City, Hokkaido in Japan. The area is underlain by Andesite and Tuff and prone to landslides. Slope angle and surface roughness were calculated from 5 m resolution DEM. These filters were chosen because colluvial materials deposit at around the angle of repose and accumulation of loose materials was considered to form a peculiar surface texture differentiable from other slope types. Field survey conducted together suggested that colluvial slopes could be identified by the filters with a probability of 80 percent. Repeat LiDAR monitoring of the site by an unmanned helicopter indicated that those slopes detected as colluviums appeared to be moving at a slow rate. In comparison with a similar study from the crushed zone in Japan, the range of slope angle indicative of colluviums agreed with the Sapporo site, while the texture was rougher due to larger debris composing the slopes.

  1. Sensor integration and testing in an airborne environment

    NASA Astrophysics Data System (ADS)

    Ricks, Timothy P.; Streling, Julie T.; Williams, Kirk W.

    2005-11-01

    The U.S. Army Redstone Technical Test Center (RTTC) has been supporting captive flight testing of missile sensors and seekers since the 1980's. Successful integration and test of sensors in an airborne environment requires attention to a broad range of disciplines. Data collection requirements drive instrumentation and flight profile configurations, which along with cost and airframe performance factors influence the choice of test aircraft. Installation methods used for instrumentation must take into consideration environmental and airworthiness factors. In addition, integration of test equipment into the aircraft will require an airworthiness release; procedures vary between the government for military aircraft, and the Federal Aviation Administration (FAA) for the use of private, commercial, or experimental aircraft. Sensor mounting methods will depend on the type of sensor being used, both for sensor performance and crew safety concerns. Pilots will require navigation input to permit the execution of accurate and repeatable flight profiles. Some tests may require profiles that are not supported by standard navigation displays, requiring the use of custom hardware/software. Test locations must also be considered in their effect on successful data collection. Restricted airspace may also be required, depending on sensor emissions and flight profiles.

  2. Neutron activation analysis of airborne thorium liberated during welding operations

    SciTech Connect

    Glasgow, D.C.; Robinson, L.; Janjovic, J.T.

    1996-02-01

    Typically, reactive metals such as aluminum are welded using a thoriated tungsten welding electrode which is attached to a source of argon gas such that the local atmosphere around the weld is inert. The metal is heated by the arc formed between the electrode and the grounded component to be welded. During this process, some of the electrode is vaporized in the arc and is potentially liberated to the surrounding air. This situation may result in a hazardous airborne thorium level. Because the electrode is consumed during welding, the electrode tip must be repeatedly dressed by grinding the tip to a fine point so that the optimal welding conditions are maintained. These grinding activities may also release thorium to the air. Data generated in the 1950s suggested that these electrodes posed no significant health hazard and seemed to justify their exemption from licensing requirements for source material. Since that time, other studies have been performed and present conflicting results as to the level of risk. Values both above and below the health protection limit in use in the United States, have been reported in the literature recently. This study is being undertaken to provide additional data which may be useful in evaluating both the chemical toxicity risk and radiological dose assessment criteria associated with thoriated tungsten welding operations.

  3. Latest Advancement In Airborne Relative Gravity Instrumentation.

    NASA Astrophysics Data System (ADS)

    Brady, N.

    2011-12-01

    Airborne gravity surveying has been performed with widely varying degrees of success since early experimentation with the Lacoste and Romberg dynamic meter in the 1950s. There are a number of different survey systems currently in operation including relative gravity meters and gradiometers. Airborne gravity is ideally suited to rapid, wide coverage surveying and is not significantly more expensive in more remote and inhospitable terrain which makes airborne measurements one of the few viable options available for cost effective exploration. As improved instrumentation has become available, scientific applications have also been able to take advantage for use in determining sub surface geologic structures, for example under ice sheets in Antarctica, and more recently direct measurement of the geoid to improve the vertical datum in the United States. In 2004, Lacoste and Romberg (now Micro-g Lacoste) decided to build on their success with the newly developed AirSea II dynamic meter and use that system as the basis for a dedicated airborne gravity instrument. Advances in electronics, timing and positioning technology created the opportunity to refine both the hardware and software, and to develop a truly turnkey system that would work well for users with little or no airborne gravity experience as well as those with more extensive experience. The resulting Turnkey Airborne Gravity System (TAGS) was successfully introduced in 2007 and has since been flown in applications from oil, gas and mineral exploration surveys to regional gravity mapping and geoid mapping. The system has been mounted in a variety of airborne platforms including depending on the application of interest. The development experience with the TAGS enabled Micro-g Lacoste to embark on a new project in 2010 to completely redesign the mechanical and electronic components of the system rather than continuing incremental upgrades. Building on the capabilities of the original TAGS, the objectives for the

  4. Indoor Pollutant Exposures Modify the Effect of Airborne Endotoxin on Asthma in Urban Children

    PubMed Central

    Hansel, Nadia N.; Aloe, Charles; Schiltz, Allison M.; Peng, Roger D.; Rabinovitch, Nathan; Ong, Mary Jane; Williams, D’Ann L.; Breysse, Patrick N.; Diette, Gregory B.; Liu, Andrew H.

    2013-01-01

    Rationale: The effect of endotoxin on asthma morbidity in urban populations is unclear. Objectives: To determine if indoor pollutant exposure modifies the relationships between indoor airborne endotoxin and asthma health and morbidity. Methods: One hundred forty-six children and adolescents with persistent asthma underwent repeated clinical assessments at 0, 3, 6, 9, and 12 months. Home visits were conducted at the same time points for assessment of airborne nicotine, endotoxin, and nitrogen dioxide (NO2) concentrations. The effect of concomitant pollutant exposure on relationships between endotoxin and asthma outcomes were examined in stratified analyses and statistical models with interaction terms. Measurements and Main Results: Both air nicotine and NO2 concentrations modified the relationships between airborne endotoxin and asthma outcomes. Among children living in homes with no detectable air nicotine, higher endotoxin was inversely associated with acute visits and oral corticosteroid bursts, whereas among those in homes with detectable air nicotine, endotoxin was positively associated with these outcomes (interaction P value = 0.004 and 0.07, respectively). Among children living in homes with lower NO2 concentrations (<20 ppb), higher endotoxin was positively associated with acute visits, whereas among those living in homes with higher NO2 concentrations, endotoxin was negatively associated with acute visit (interaction P value = 0.05). NO2 also modified the effect of endotoxin on asthma symptom outcomes in a similar manner. Conclusions: The effects of household airborne endotoxin exposure on asthma are modified by coexposure to air nicotine and NO2, and these pollutants have opposite effects on the relationships between endotoxin and asthma-related outcomes. PMID:24066676

  5. Maximum power tracking

    SciTech Connect

    O'Sullivan, G.

    1983-03-01

    By definition, a maximum power tracking device causes the photovoltaic array to operate on the locus of maximum power points within a specified accuracy. There are limitations to the application of maximum power tracking. A prerequisite is that the load be capable of absorbing all of the power availble at all times. Battery chargers, electrical heaters, water pumps, and most significantly, returning power to the utility grid, are prime examples of applications that are adaptable to maximum power tracking. Maximum power tracking is available to either dc or ac loads. An inverter equipped with a means of changing input voltage by controlling its input impedance can deliver maximum power to ac loads. The inverter can be fixed or variable frequency and fixed or variable voltage, but must be compatible with the ac load. The discussion includes applications, techniques, and cost factors.

  6. Enhanced optical tracking

    NASA Astrophysics Data System (ADS)

    McSheery, Tracy

    2008-04-01

    Enhanced tracking is accomplished by increasing the resolution, frame rate and processing capabilities in tracking dynamic regions of interest for vision applications. In many proven algorithms, the ability to distinguish an object and track it is dependent on the system performance in more than one attribute. We have conducted studies on proven techniques such as Active Appearance Models, Principle Component Analysis and Eigen tracking. All perform better as the camera resolution increases, and camera frame rate increases. Additional opportunities have been observed by combining these techniques, taking advantage of Multicore CPUs, and GPU graphic card processing. Results from an 8 Megapixel commercial sensor combined with a Field Programmable Gate array are presented, and algorithm performance compared with down scaled images of the same scenes, and simulated typical 30 hertz frame rates verses the 120 hertz to 300 hertz typical of this smart camera.

  7. Energy Tracking Software Platform

    SciTech Connect

    Ryan Davis; Nathan Bird; Rebecca Birx; Hal Knowles

    2011-04-04

    Acceleration has created an interactive energy tracking and visualization platform that supports decreasing electric, water, and gas usage. Homeowners have access to tools that allow them to gauge their use and track progress toward a smaller energy footprint. Real estate agents have access to consumption data, allowing for sharing a comparison with potential home buyers. Home builders have the opportunity to compare their neighborhood's energy efficiency with competitors. Home energy raters have a tool for gauging the progress of their clients after efficiency changes. And, social groups are able to help encourage members to reduce their energy bills and help their environment. EnergyIT.com is the business umbrella for all energy tracking solutions and is designed to provide information about our energy tracking software and promote sales. CompareAndConserve.com (Gainesville-Green.com) helps homeowners conserve energy through education and competition. ToolsForTenants.com helps renters factor energy usage into their housing decisions.

  8. Advanced Doppler tracking experiments

    NASA Technical Reports Server (NTRS)

    Armstrong, J. W.

    1989-01-01

    The Doppler tracking method is currently the only technique available for broadband gravitational wave searches in the approx. 10(exp -4) to 10(exp -1) Hz low frequency band. A brief review is given of the Doppler method, a discussion of the main noise sources, and a review of experience with current spacecraft and the prospects for sensitivity improvements in an advanced Doppler tracking experiment.

  9. TELAER: a multi-mode/multi-antenna interferometric airborne SAR system

    NASA Astrophysics Data System (ADS)

    Perna, Stefano; Amaral, Tiago; Berardino, Paolo; Esposito, Carmen; Jackson, Giuseppe; Pauciullo, Antonio; Vaz Junior, Eurico; Wimmer, Christian; Lanari, Riccardo

    2014-05-01

    The present contribution is aimed at showing the capabilities of the TELAER airborne Synthetic Aperture Radar (SAR) system recently upgraded to the interferometric mode [1]. TELAER is an Italian airborne X-Band SAR system, mounted onboard a LearJet 35A aircraft. Originally equipped with a single TX/RX antenna, it now operates in single-pass interferometric mode thanks to a system upgrading [1] funded by the Italian National Research Council (CNR), via the Italian Ministry of Education, Universities and Research (MIUR), in the framework of a cooperation between CNR and the Italian Agency for Agriculture Subsidy Payments (AGEA). In the frame of such cooperation, CNR has entrusted the Institute for Electromagnetic Sensing of the Environment (IREA) for managing all the activities, included the final flight tests, related to the system upgrading. According to such an upgrading, two additional receiving X-band antennas have been installed in order to allow, simultaneously, single-pass Across-Track and Along-Track interferometry [1]. More specifically, the three antennas are now installed in such a way to produce three different across-track baselines and two different along-track baselines. Moreover, in the frame of the same system upgrading, it has been mounted onboard the Learjet an accurate embedded Global Navigation Satellite System and Inertial Measurement Unit equipment. This allows precise measurement of the tracks described by the SAR antennas during the flight, in order to accurately implement Motion Compensation (MOCO) algorithms [2] during the image formation (focusing) step. It is worth remarking that the TELAER system upgraded to the interferometric mode is very flexible, since the user can set different operational modes characterized by different geometric resolutions and range swaths. In particular, it is possible to reach up to 0.5 m of resolution with a range swath of 2km; conversely, it is possible to enlarge the range swath up to 10 km at expenses of

  10. MATERIAL TRACKING USING LANMAS

    SciTech Connect

    Armstrong, F.

    2010-06-07

    LANMAS is a transaction-based nuclear material accountability software product developed to replace outdated and legacy accountability systems throughout the DOE. The core underlying purpose of LANMAS is to track nuclear materials inventory and report transactions (movement, mixing, splitting, decay, etc.) to the Nuclear Materials Management and Safeguards System (NMMSS). While LANMAS performs those functions well, there are many additional functions provided by the software product. As a material is received onto a site or created at a site, its entire lifecycle can be tracked in LANMAS complete to its termination of safeguards. There are separate functions to track material movements between and within material balance areas (MBAs). The level of detail for movements within a MBA is configurable by each site and can be as high as a site designation or as detailed as building/room/rack/row/position. Functionality exists to track the processing of materials, either as individual items or by modeling a bulk process as an individual item to track inputs and outputs from the process. In cases where sites have specialized needs, the system is designed to be flexible so that site specific functionality can be integrated into the product. This paper will demonstrate how the software can be used to input material into an account and track it to its termination of safeguards.

  11. Dual baseline and frequency along-track interferometry

    NASA Technical Reports Server (NTRS)

    Carande, Richard E.

    1992-01-01

    The Jet Propulsion Laboratory (JPL) airborne synthetic aperture radar (AIRSAR) L-band along-track interferometer images currents and waves on the ocean surface. By modifying the operating procedure of this two antenna interferometer, a technique has been developed to enable interferometric measurements to be made simultaneously at two different baselines. The availability of such data allows measurement of the decorrelation process of the ocean in greater detail. The coherence time of the ocean surface can be measured at high resolution over large areas. In addition to the L-band interferometer, a C-band along-track interferometer has been developed. It allows C-band dual-baseline measurements to be made simultaneous with the L-band measurements. The dual-baseline technique and AIRSAR implementation are described, and some example data are presented.

  12. 3D target tracking in infrared imagery by SIFT-based distance histograms

    NASA Astrophysics Data System (ADS)

    Yan, Ruicheng; Cao, Zhiguo

    2011-11-01

    SIFT tracking algorithm is an excellent point-based tracking algorithm, which has high tracking performance and accuracy due to its robust capability against rotation, scale change and occlusion. However, when tracking a huge 3D target in complicated real scenarios in a forward-looking infrared (FLIR) image sequence taken from an airborne moving platform, the tracked point locating in the vertical surface usually shifts away from the correct position. In this paper, we propose a novel algorithm for 3D target tracking in FLIR image sequences. Our approach uses SIFT keypoints detected in consecutive frames for point correspondence. The candidate position of the tracked point is firstly estimated by computing the affine transformation using local corresponding SIFT keypoints. Then the correct position is located via an optimal method. Euclidean distances between a candidate point and SIFT keypoints nearby are calculated and formed into a SIFT-based distance histogram. The distance histogram is defined a cost of associating each candidate point to a correct tracked point using the constraint based on the topology of each candidate point with its surrounding SIFT keypoints. Minimization of the cost is formulated as a combinatorial optimization problem. Experiments demonstrate that the proposed algorithm efficiently improves the tracking performance and accuracy.

  13. A Probabilistic Cell Tracking Algorithm

    NASA Astrophysics Data System (ADS)

    Steinacker, Reinhold; Mayer, Dieter; Leiding, Tina; Lexer, Annemarie; Umdasch, Sarah

    2013-04-01

    The research described below was carried out during the EU-Project Lolight - development of a low cost, novel and accurate lightning mapping and thunderstorm (supercell) tracking system. The Project aims to develop a small-scale tracking method to determine and nowcast characteristic trajectories and velocities of convective cells and cell complexes. The results of the algorithm will provide a higher accuracy than current locating systems distributed on a coarse scale. Input data for the developed algorithm are two temporally separated lightning density fields. Additionally a Monte Carlo method minimizing a cost function is utilizied which leads to a probabilistic forecast for the movement of thunderstorm cells. In the first step the correlation coefficients between the first and the second density field are computed. Hence, the first field is shifted by all shifting vectors which are physically allowed. The maximum length of each vector is determined by the maximum possible speed of thunderstorm cells and the difference in time for both density fields. To eliminate ambiguities in determination of directions and velocities, the so called Random Walker of the Monte Carlo process is used. Using this method a grid point is selected at random. Moreover, one vector out of all predefined shifting vectors is suggested - also at random but with a probability that is related to the correlation coefficient. If this exchange of shifting vectors reduces the cost function, the new direction and velocity are accepted. Otherwise it is discarded. This process is repeated until the change of cost functions falls below a defined threshold. The Monte Carlo run gives information about the percentage of accepted shifting vectors for all grid points. In the course of the forecast, amplifications of cell density are permitted. For this purpose, intensity changes between the investigated areas of both density fields are taken into account. Knowing the direction and speed of thunderstorm

  14. Repeated controlled rockfall trajectory testing

    NASA Astrophysics Data System (ADS)

    Volkwein, Axel; Krummenacher, Barbara; Gerber, Werner; Lardon, Jessica; Gees, Fabio; Brügger, Lucas; Ott, Thomas

    2015-04-01

    The variability of rockfall trajectories regarding their travel paths, velocities, run out distances and jump heights requires statistical and stochastic methods for both the analysis of field values and numerical simulations. However, the perturbations mostly are considered only within the simulations because only few stochastic data are available coming from the field. This means, simulation software is calibrated based on the data of single rockfall events without the knowledge whether the observed/recorded events were average or extreme ones. In a field study we now tested the conduction of rockfall tests on a natural slope using natural boulders. Each boulder was thrown several times from the same starting point. This procedure provides a view on the variability of the different trajectories. The outcome helps to better understand the rockfall process but more provides valuable datasets that can be used for the calibration of rockfall simulation models. The rockfall experiments were recorded using two high speed cameras, an internal independent high frequency data logging unit measuring 3D accelerations and 3D rotational velocities. An external so-called "Local Positioning System" enabled a live tracking of the blocks in the field. More than repetitions were achieved using mainly 4 different blocks. The presentation shows the first analysis of the experiments including validation of measurement systems, the natural variability of the rockfall tests and comparison with corresponding theory and simulations.

  15. Trinucleotide Repeats: A Structural Perspective

    PubMed Central

    Almeida, Bruno; Fernandes, Sara; Abreu, Isabel A.; Macedo-Ribeiro, Sandra

    2013-01-01

    Trinucleotide repeat (TNR) expansions are present in a wide range of genes involved in several neurological disorders, being directly involved in the molecular mechanisms underlying pathogenesis through modulation of gene expression and/or the function of the RNA or protein it encodes. Structural and functional information on the role of TNR sequences in RNA and protein is crucial to understand the effect of TNR expansions in neurodegeneration. Therefore, this review intends to provide to the reader a structural and functional view of TNR and encoded homopeptide expansions, with a particular emphasis on polyQ expansions and its role at inducing the self-assembly, aggregation and functional alterations of the carrier protein, which culminates in neuronal toxicity and cell death. Detail will be given to the Machado-Joseph Disease-causative and polyQ-containing protein, ataxin-3, providing clues for the impact of polyQ expansion and its flanking regions in the modulation of ataxin-3 molecular interactions, function, and aggregation. PMID:23801983

  16. Observations of Soft Gamma Repeaters

    NASA Technical Reports Server (NTRS)

    Kouveliotou, Chryssa

    2005-01-01

    Magnetars (Soft Gamma Repeaters and Anomalous X-ray Pulsars) are a subclass of neutron stars characterized by their recurrent X-ray bursts. While in an active (bursting) state (lasting anywhere between days and years), they are emitting hundreds of predominantly soft (kl'=30 kev), short (0.1 - 100 ms long) events. Their quiescent source X-ray light curves exhibit pulsations in the narrow range of 5-1 1 s; estimates of these rotational period rate changes (spin-down) indicate that their magnetic fields are extremely high, of the order of 10A14-10A15 G. Such high B-field objects, dubbed "magnetars", had been predicted to exist in 1992, but the first concrete observational evidence was obtained in 1998 for two of these sources. Very recently, SGR1806-20 emitted a giant flare, which was detected in the radio with a multitude of telescopes under an extensive international campaign. These observations have revealed exciting new results, never seen before in any of the other magnetar sources. I will discuss here these results and their relevance to our understanding of the nature of magnetars.

  17. Modeling Repeatedly Flaring δ Sunspots.

    PubMed

    Chatterjee, Piyali; Hansteen, Viggo; Carlsson, Mats

    2016-03-11

    Active regions (ARs) appearing on the surface of the Sun are classified into α, β, γ, and δ by the rules of the Mount Wilson Observatory, California on the basis of their topological complexity. Amongst these, the δ sunspots are known to be superactive and produce the most x-ray flares. Here, we present results from a simulation of the Sun by mimicking the upper layers and the corona, but starting at a more primitive stage than any earlier treatment. We find that this initial state consisting of only a thin subphotospheric magnetic sheet breaks into multiple flux tubes which evolve into a colliding-merging system of spots of opposite polarity upon surface emergence, similar to those often seen on the Sun. The simulation goes on to produce many exotic δ sunspot associated phenomena: repeated flaring in the range of typical solar flare energy release and ejective helical flux ropes with embedded cool-dense plasma filaments resembling solar coronal mass ejections. PMID:27015469

  18. Airborne Microwave Imaging of River Velocities

    NASA Technical Reports Server (NTRS)

    Plant, William J.

    2002-01-01

    The objective of this project was to determine whether airborne microwave remote sensing systems can measure river surface currents with sufficient accuracy to make them prospective instruments with which to monitor river flow from space. The approach was to fly a coherent airborne microwave Doppler radar, developed by APL/UW, on a light airplane along several rivers in western Washington state over an extended period of time. The fundamental quantity obtained by this system to measure river currents is the mean offset of the Doppler spectrum. Since this scatter can be obtained from interferometric synthetic aperture radars (INSARs), which can be flown in space, this project provided a cost effective means for determining the suitability of spaceborne INSAR for measuring river flow.

  19. The Callaway Plant's airborne tritium sampling cart

    SciTech Connect

    Graham, C.C.; Roselius, R.R. )

    1986-07-01

    The water vapor condensation method for sampling airborne tritium offers significant advantages over other methods, including minimal sample preparation, high sensitivity, and independence from collection efficiency and sample flow rate. However, it does have disadvantages that must be overcome in the design of a sampler. This article describes a cart-mounted, portable airborne tritium sampler used at the Callaway Nuclear Plant that incorporates the advantages of the condensation technique while minimizing its shortcomings. The key elements in the design of the sampler are the use of a refrigerated bath to cool a series of three water vapor collection traps and the use of an optical condensation dew point hygrometer to measure the moisture content of the sample. Design considerations for the proper operation of dew point hygrometers are presented, and the method used to convert due point readings to water vapor content is described.

  20. Satellite orbit determination from an airborne platform

    NASA Astrophysics Data System (ADS)

    Shepard, M. M.; Foshee, J. J.

    This paper describes the requirements, approach, and problems associated with autonomous satellite orbit determination from an airborne platform. The ability to perform orbit determination from an airborne platform removes the reliance on ground control facilities. Aircraft orbit determination offers a more robust system in that it is less susceptible to direct attack, sabotage, or nuclear disaster. Ranging on a satellite and the processing of range/range-rate data along with INS inputs to produce a set of orbital parameters to be transmitted to user terminals are discussed. Several algorithms that could be utilized by the user terminal to recover the satellite position/velocity data from the transmitted message are presented. The ability to compress the ephemeris message to a small size while remaining autonomous for a long period of time, as would be needed in future military communication satellites, is discussed.

  1. Performance metrics for an airborne imaging system

    NASA Astrophysics Data System (ADS)

    Dayton, David C.; Gonglewski, John D.

    2004-11-01

    A series of airborne imaging experiments have been conducted on the island of Maui and at North Oscura Peak in New Mexico. Two platform altitudes were considered 3000 meters and 600 meters, both with a slant range to the target up to 10000 meters. The airborne imaging platform was a Twin Otter aircraft, which circled ground target sites. The second was a fixed platform on a mountain peak overlooking a valley 600 meters below. The experiments were performed during the day using solar illuminated target buildings. Imaging system performance predictions were calculated using standard atmospheric turbulence models, and aircraft boundary layer models. Several different measurement approaches were then used to estimate the actual system performance, and make comparisons with the calculations.

  2. Molecular spectroscopy from the Kuiper Airborne Observatory

    NASA Technical Reports Server (NTRS)

    Beckwith, S.

    1985-01-01

    Interstellar and circumstellar molecules are investigated through medium-resolution infrared spectrosocpy of the vibration-rotation and pure rotational transitions. A primary goal was the construction and improvement of instrumentation for the near and middle infrared regions, wavelengths between 2 and 10 microns. The main instrument was a cooled grating spectrometer with an interchangeable detector focal plane which could be used on the Kuiper Airborne Observatory (KAO) for airborne observations, and also at ground-based facilities. Interstellar shock waves were investigated by H2 emission from the Orion Nebula, W51, and the proto-planetary nebulae CRL 2688 and CRL 618. The observations determined the physical conditions in shocked molecular gas near these objects. From these it was possible to characterize the energetic history of mass loss from both pre- and post-main sequence stars in the regions.

  3. Airborne Infrared Spectroscopy of 1994 Western Wildfires

    NASA Technical Reports Server (NTRS)

    Worden, Helen; Beer, Reinhard; Rinsland, Curtis P.

    1997-01-01

    In the summer of 1994 the 0.07/ cm resolution infrared Airborne Emission Spectrometer (AES) acquired spectral data over two wildfires, one in central Oregon on August 3 and the other near San Luis Obispo, California, on August 15. The spectrometer was on board a NASA DC-8 research aircraft, flying at an altitude of 12 km. The spectra from both fires clearly show features due to water vapor, carbon dioxide, carbon monoxide, ammonia, methanol, formic acid, and ethylene at significantly higher abundance and temperature than observed in downlooking spectra of normal atmospheric and ground conditions. Column densities are derived for several species, and molar ratios are compared with previous biomass fire measurements. We believe that this is the first time such data have been acquired by airborne spectral remote sensing.

  4. Analyzing Options for Airborne Emergency Wireless Communications

    SciTech Connect

    Michael Schmitt; Juan Deaton; Curt Papke; Shane Cherry

    2008-03-01

    In the event of large-scale natural or manmade catastrophic events, access to reliable and enduring commercial communication systems is critical. Hurricane Katrina provided a recent example of the need to ensure communications during a national emergency. To ensure that communication demands are met during these critical times, Idaho National Laboratory (INL) under the guidance of United States Strategic Command has studied infrastructure issues, concerns, and vulnerabilities associated with an airborne wireless communications capability. Such a capability could provide emergency wireless communications until public/commercial nodes can be systematically restored. This report focuses on the airborne cellular restoration concept; analyzing basic infrastructure requirements; identifying related infrastructure issues, concerns, and vulnerabilities and offers recommended solutions.

  5. Airborne source localization in shallow water

    NASA Astrophysics Data System (ADS)

    Peng, Zhaohui; Wang, Guangxu

    2012-11-01

    Owing to the great difference of acoustic characteristic impedance between air and water, the sound transmission loss from an airborne source into water is very high. So, it is very difficult to do experimental research on air-to-water sound propagation. An experiment was conducted for air-to-water sound propagation in the South China Sea in 2010. A HLA placed on the sea bottom was used to receive signals sent by a high-power loudspeaker hung on a research ship floating 1km to 4km away from the HLA. The locations of airborne sources are estimated from the signals measured by the HLA. The estimated DOA and ranges are in agreement with the GPS records.

  6. Airborne ICESat-2 simulator (MABEL) results from Greenland

    NASA Astrophysics Data System (ADS)

    Neumann, T.; Markus, T.; Brunt, K. M.; Walsh, K.; Hancock, D.; Cook, W. B.; Brenner, A. C.; Csatho, B. M.; De Marco, E.

    2012-12-01

    The Ice, Cloud, and land Elevation Satellite-2 (ICESat-2) is a next-generation laser altimeter designed to continue key observations of sea ice freeboard, ice sheet elevation change, vegetation canopy height, earth surface elevation and sea surface heights. Scheduled for launch in mid-2016, ICESat-2 will collect data between 88 degrees north and south using a high-repetition rate (10 kHz) laser operating at 532nm, and using a photon-counting detection strategy. Our airborne simulator, the Multiple Altimeter Beam Experimental Lidar (MABEL) uses a similar photon-counting measurement strategy, operates at 532nm (16 beams) and 1064 nm (8 beams) to collect similar data to what we expect for ICESat-2. The comparison between frequencies allows for studies of possible penetration of green light into water or snow. MABEL collects more spatially-dense data than ICESat-2 (2cm along-track vs. 70 cm along track for ICESat-2, and has a smaller footprint than ICESat-2 (2m nominal diameter vs. 10m nominal diameter for ICESat-2) requiring geometric and radiometric scaling to relate MABEL data to simulate ICESat-2 data. We based MABEL out of Keflavik, Iceland during April 2012, and collected ~ 100 hours of data from 20km altitude over a variety of targets. MABEL collected sea ice data over the Nares Strait, and off the east coast of Greenland, the later flight in coordination with NASA's Operation IceBridge, which collected ATM data along the same track within 90 minutes of MABEL data collection. MABEL flew a variety of lines over Greenland in the southwest, Jakobshavn region, and over the ice sheet interior, including 4 hours of coincident data with Operation IceBridge in southwest Greenland. MABEL flew a number of calibration sites, including corner cubes in Svalbard, Summit Station (where a GPS survey of the surface elevation was collected within an hour of our overflight), and well-surveyed targets in Iceland and western Greenland. In this presentation, we present an overview of

  7. Characterizing Subglacial Interfaces With Airborne Radar Sounding Techniques

    NASA Astrophysics Data System (ADS)

    Peters, M. E.; Blankenship, D. D.; Morse, D. L.

    2004-12-01

    Ice sheets are sensitive indicators of global change including sea-level rise. An ice sheet's subglacial interface is an important factor controlling its dynamic behavior. In particular, the grounding zones of ice streams and subglacial lakes are complex systems involving the interaction of the moving ice mass with underlying materials such as liquid water, saturated lubricating tills, and rough or frozen bedrock sticky spots. Imaging and characterizing the subglacial environment of ice sheets is fundamental to understanding these complex systems. Airborne radar sounding is a powerful and well-known technique for studying ice sheets and glaciers and their contiguous underlying environments. We present results from data acquired in 2001 over the ice stream C grounding zone in West Antarctica, as well as over a hypothesized subglacial lake near the South Pole. These data were acquired using a uniquely configured coherent airborne radar system. Our focus has been to characterize the subglacial interface through radar echo analysis based on reflection and scattering theory. The radar system uses a programmable signal source linked to a 10 kW transmitter and a dual-channel coherent down-conversion receiver. The radar operates in chirped pulse mode at 60 MHz with 15 MHz bandwidth. High and low-gain channels allow for recording a wide dynamic range of echoes simultaneously and without range-dependent gain control. Data acquisition includes integrations of 16 returned radar signals about every 15 cm along-track. Pulse compression and synthetic aperture radar (SAR) processing were components of data analysis. Subglacial echoes are influenced by the physical properties of the interface such as the composition and roughness of the materials at the interface. Other important factors include dielectric losses and volumetric scattering losses from propagation through the ice as well as transmission and refraction at the air-ice interface. Unfocussed SAR narrows the along-track

  8. Wideband radar for airborne minefield detection

    NASA Astrophysics Data System (ADS)

    Clark, William W.; Burns, Brian; Dorff, Gary; Plasky, Brian; Moussally, George; Soumekh, Mehrdad

    2006-05-01

    Ground Penetrating Radar (GPR) has been applied for several years to the problem of detecting both antipersonnel and anti-tank landmines. RDECOM CERDEC NVESD is developing an airborne wideband GPR sensor for the detection of minefields including surface and buried mines. In this paper, we describe the as-built system, data and image processing techniques to generate imagery, and current issues with this type of radar. Further, we will display images from a recent field test.

  9. A new tool for sampling airborne isocyanates

    SciTech Connect

    Sesana, G.; Nano, G.; Baj, A. )

    1991-05-01

    A new sampling system is presented that uses solid sorbent media contained in a tube for the determination of airborne isocyanates (2.4-2.6 toluene diisocyanate, hexamethylene diisocyanate, and 4.4' diaminodiphenylmethane diisocyanate). The method is compared with the National Institute for Occupational Safety and Health (NIOSH) Method P CAM 5505 (Revision {number sign}1). Experimental tests yielded results that were highly concordant with the NIOSH method.

  10. First airborne pathogen direct analysis system.

    PubMed

    Liu, Qi; Zhang, Yuxiao; Jing, Wenwen; Liu, Sixiu; Zhang, Dawei; Sui, Guodong

    2016-03-01

    We report a portable "sample to answer" system for the rapid detection of airborne pathogens for the first time. The system contains a key microfluidic chip which fulfills both pathogen enrichment and biological identification functions. The system realizes simple operation and less human intervention as well as minimum reagent contamination. The operation is user-friendly and suitable for field and point-of-care applications. The system is capable of handling detection of different pathogens by changing the primers. PMID:26854120

  11. Airborne Visible/Infrared Imaging Spectrometer (AVIRIS)

    NASA Technical Reports Server (NTRS)

    Macenka, Steven A.; Chrisp, Michael P.

    1988-01-01

    The development of the Airborne Visible/Infrared Imaging Spectrometer (AVIRIS) has been completed at JPL. This paper outlines the functional requirements of the spectrometer optics subsystem, and describes the spectrometer optical design. The optical subsystem performance is shown in terms of spectral modulation transfer functions, radial energy distributions, and system transmission at selected wavelengths for the four spectrometers. An outline of the spectrometer alignment is included.

  12. Holographic Airborne Rotating Lidar Instrument Experiment (HARLIE)

    NASA Technical Reports Server (NTRS)

    Schwemmer, Geary K.

    1998-01-01

    Scanning holographic lidar receivers are currently in use in two operational lidar systems, PHASERS (Prototype Holographic Atmospheric Scanner for Environmental Remote Sensing) and now HARLIE (Holographic Airborne Rotating Lidar Instrument Experiment). These systems are based on volume phase holograms made in dichromated gelatin (DCG) sandwiched between 2 layers of high quality float glass. They have demonstrated the practical application of this technology to compact scanning lidar systems at 532 and 1064 nm wavelengths, the ability to withstand moderately high laser power and energy loading, sufficient optical quality for most direct detection systems, overall efficiencies rivaling conventional receivers, and the stability to last several years under typical lidar system environments. Their size and weight are approximately half of similar performing scanning systems using reflective optics. The cost of holographic systems will eventually be lower than the reflective optical systems depending on their degree of commercialization. There are a number of applications that require or can greatly benefit from a scanning capability. Several of these are airborne systems, which either use focal plane scanning, as in the Laser Vegetation Imaging System or use primary aperture scanning, as in the Airborne Oceanographic Lidar or the Large Aperture Scanning Airborne Lidar. The latter class requires a large clear aperture opening or window in the aircraft. This type of system can greatly benefit from the use of scanning transmission holograms of the HARLIE type because the clear aperture required is only about 25% larger than the collecting aperture as opposed to 200-300% larger for scan angles of 45 degrees off nadir.

  13. The Caltech airborne submillimeter SIS receiver

    NASA Technical Reports Server (NTRS)

    Zmuidzinas, Jonas; Carlstrom, J.; Miller, D.; Ugras, N. G.

    1995-01-01

    We have constructed a sensitive submillimeter receiver for the NASA Kuiper Airborne Observatory (KAO) which at present operates in the 500-750 GHz band. The DSB receiver noise temperature is about 5 h nu/k(sub B) over the 500-700 GHz range. This receiver has been used to detect H2O(18)O, HCl, and CH in interstellar molecular clouds, and also to search for C(+) emission from the highly redshifted galaxy (z = 2.3) IRAS 10214.

  14. Airborne electronics for automated flight systems

    NASA Technical Reports Server (NTRS)

    Graves, G. B., Jr.

    1975-01-01

    The increasing importance of airborne electronics for use in automated flight systems is briefly reviewed with attention to both basic aircraft control functions and flight management systems for operational use. The requirements for high levels of systems reliability are recognized. Design techniques are discussed and the areas of control systems, computing and communications are considered in terms of key technical problems and trends for their solution.

  15. Airborne Chemical Sensing with Mobile Robots

    PubMed Central

    Lilienthal, Achim J.; Loutfi, Amy; Duckett, Tom

    2006-01-01

    Airborne chemical sensing with mobile robots has been an active research area since the beginning of the 1990s. This article presents a review of research work in this field, including gas distribution mapping, trail guidance, and the different subtasks of gas source localisation. Due to the difficulty of modelling gas distribution in a real world environment with currently available simulation techniques, we focus largely on experimental work and do not consider publications that are purely based on simulations.

  16. NASA's Airborne Astronomy Program - Lessons For SOFIA

    NASA Astrophysics Data System (ADS)

    Erickson, Edwin F.

    2007-07-01

    Airborne astronomy was pioneered and has evolved at NASA Ames Research Center near San Francisco, California, since 1965. Nowhere else in the world has a similar program been implemented. Its many unique features deserve description, especially for the benefit of planning the operation of SOFIA, the Stratospheric Observatory for Infrared Astronomy, and in particular since NASA Headquarters’ recent decision to base SOFIA operations at Dryden Flight Research Center at Edwards, California instead of at Ames. The history of Ames’ airborne astronomy program is briefly summarized. Discussed in more detail are the operations and organization of the 21-year Kuiper Airborne Observatory (KAO) program, which provide important lessons for SOFIA. The KAO program is our best prototype for planning effective SOFIA operations. Principal features of the KAO program which should be retained on SOFIA are: unique science, innovative new science instruments and technologies, training of young scientists, an effective education and public outreach program, flexibility, continuous improvement, and efficient operations with a lean, well integrated team. KAO program features which should be improved upon with SOFIA are: (1) a management structure that is dedicated primarily to safely maximizing scientific productivity for the resources available, headed by a scientist who is the observatory director, and (2) stimuli to assure prompt distribution and accessibility of data to the scientific community. These and other recommendations were recorded by the SOFIA Science Working Group in 1995, when the KAO was decommissioned to start work on SOFIA. Further operational and organizational factors contributing to the success of the KAO program are described. Their incorporation into SOFIA operations will help assure the success of this new airborne observatory. SOFIA is supported by NASA in the U.S. and DLR (the German Aerospace Center) in Germany.

  17. Improved Airborne System for Sensing Wildfires

    NASA Technical Reports Server (NTRS)

    McKeown, Donald; Richardson, Michael

    2008-01-01

    The Wildfire Airborne Sensing Program (WASP) is engaged in a continuing effort to develop an improved airborne instrumentation system for sensing wildfires. The system could also be used for other aerial-imaging applications, including mapping and military surveillance. Unlike prior airborne fire-detection instrumentation systems, the WASP system would not be based on custom-made multispectral line scanners and associated custom- made complex optomechanical servomechanisms, sensors, readout circuitry, and packaging. Instead, the WASP system would be based on commercial off-the-shelf (COTS) equipment that would include (1) three or four electronic cameras (one for each of three or four wavelength bands) instead of a multispectral line scanner; (2) all associated drive and readout electronics; (3) a camera-pointing gimbal; (4) an inertial measurement unit (IMU) and a Global Positioning System (GPS) receiver for measuring the position, velocity, and orientation of the aircraft; and (5) a data-acquisition subsystem. It would be necessary to custom-develop an integrated sensor optical-bench assembly, a sensor-management subsystem, and software. The use of mostly COTS equipment is intended to reduce development time and cost, relative to those of prior systems.

  18. Methods for sampling of airborne viruses.

    PubMed

    Verreault, Daniel; Moineau, Sylvain; Duchaine, Caroline

    2008-09-01

    To better understand the underlying mechanisms of aerovirology, accurate sampling of airborne viruses is fundamental. The sampling instruments commonly used in aerobiology have also been used to recover viruses suspended in the air. We reviewed over 100 papers to evaluate the methods currently used for viral aerosol sampling. Differentiating infections caused by direct contact from those caused by airborne dissemination can be a very demanding task given the wide variety of sources of viral aerosols. While epidemiological data can help to determine the source of the contamination, direct data obtained from air samples can provide very useful information for risk assessment purposes. Many types of samplers have been used over the years, including liquid impingers, solid impactors, filters, electrostatic precipitators, and many others. The efficiencies of these samplers depend on a variety of environmental and methodological factors that can affect the integrity of the virus structure. The aerodynamic size distribution of the aerosol also has a direct effect on sampler efficiency. Viral aerosols can be studied under controlled laboratory conditions, using biological or nonbiological tracers and surrogate viruses, which are also discussed in this review. Lastly, general recommendations are made regarding future studies on the sampling of airborne viruses. PMID:18772283

  19. Airborne electromagnetic hydrocarbon mapping in Mozambique

    NASA Astrophysics Data System (ADS)

    Pfaffhuber, Andreas A.; Monstad, Ståle; Rudd, Jonathan

    2009-09-01

    The Inhaminga hydrocarbon exploration licence in central Mozambique sets the location for a multi-method airborne geophysical survey. The size of the Inhaminga block, spanning some 16500km2 from Beira to the Zambezi, limited available data and a tight exploration schedule made an airborne survey attractive for the exploration portfolio. The aim of the survey was to map hydrocarbon seepage zones based on the evidence that seepage may create resistivity, radiometric and sometimes magnetic anomalies. The survey involved a helicopter-borne time domain electromagnetic induction system (AEM) and a fixed wing magnetic gradiometer and radiometer. Our data analysis highlights an anomaly extending some tens of kilometres through the survey area along the eastern margin of the Urema Graben. The area is imaged by AEM as a shallow resistive unit below a strong surface conductor and shows high Uranium and low Potassium concentrations (normalised to mean Thorium ratios). A seismic dimming zone on a 2D seismic line crossing the area coincides with the resistivity and radiometric anomaly. The geological exploration model expects seepage to be linked to the graben fault systems and an active seep has been sampled close to the anomaly. We thus interpret this anomaly to be associated with a gas seepage zone. Further geological ground work and seismic investigations are planned to assess this lead. Airborne data has further improved the general understanding of the regional geology allowing spatial mapping of faults and other features from 2D seismic lines crossing the survey area.

  20. Airborne multispectral detection of regrowth cotton fields

    NASA Astrophysics Data System (ADS)

    Westbrook, John K.; Suh, Charles P.-C.; Yang, Chenghai; Lan, Yubin; Eyster, Ritchie S.

    2015-01-01

    Effective methods are needed for timely areawide detection of regrowth cotton plants because boll weevils (a quarantine pest) can feed and reproduce on these plants beyond the cotton production season. Airborne multispectral images of regrowth cotton plots were acquired on several dates after three shredding (i.e., stalk destruction) dates. Linear spectral unmixing (LSU) classification was applied to high-resolution airborne multispectral images of regrowth cotton plots to estimate the minimum detectable size and subsequent growth of plants. We found that regrowth cotton fields can be identified when the mean plant width is ˜0.2 m for an image resolution of 0.1 m. LSU estimates of canopy cover of regrowth cotton plots correlated well (r2=0.81) with the ratio of mean plant width to row spacing, a surrogate measure of plant canopy cover. The height and width of regrowth plants were both well correlated (r2=0.94) with accumulated degree-days after shredding. The results will help boll weevil eradication program managers use airborne multispectral images to detect and monitor the regrowth of cotton plants after stalk destruction, and identify fields that may require further inspection and mitigation of boll weevil infestations.

  1. Methods for Sampling of Airborne Viruses

    PubMed Central

    Verreault, Daniel; Moineau, Sylvain; Duchaine, Caroline

    2008-01-01

    Summary: To better understand the underlying mechanisms of aerovirology, accurate sampling of airborne viruses is fundamental. The sampling instruments commonly used in aerobiology have also been used to recover viruses suspended in the air. We reviewed over 100 papers to evaluate the methods currently used for viral aerosol sampling. Differentiating infections caused by direct contact from those caused by airborne dissemination can be a very demanding task given the wide variety of sources of viral aerosols. While epidemiological data can help to determine the source of the contamination, direct data obtained from air samples can provide very useful information for risk assessment purposes. Many types of samplers have been used over the years, including liquid impingers, solid impactors, filters, electrostatic precipitators, and many others. The efficiencies of these samplers depend on a variety of environmental and methodological factors that can affect the integrity of the virus structure. The aerodynamic size distribution of the aerosol also has a direct effect on sampler efficiency. Viral aerosols can be studied under controlled laboratory conditions, using biological or nonbiological tracers and surrogate viruses, which are also discussed in this review. Lastly, general recommendations are made regarding future studies on the sampling of airborne viruses. PMID:18772283

  2. Optical Communications Link to Airborne Transceiver

    NASA Technical Reports Server (NTRS)

    Regehr, Martin W.; Kovalik, Joseph M.; Biswas, Abhijit

    2011-01-01

    An optical link from Earth to an aircraft demonstrates the ability to establish a link from a ground platform to a transceiver moving overhead. An airplane has a challenging disturbance environment including airframe vibrations and occasional abrupt changes in attitude during flight. These disturbances make it difficult to maintain pointing lock in an optical transceiver in an airplane. Acquisition can also be challenging. In the case of the aircraft link, the ground station initially has no precise knowledge of the aircraft s location. An airborne pointing system has been designed, built, and demonstrated using direct-drive brushless DC motors for passive isolation of pointing disturbances and for high-bandwidth control feedback. The airborne transceiver uses a GPS-INS system to determine the aircraft s position and attitude, and to then illuminate the ground station initially for acquisition. The ground transceiver participates in link-pointing acquisition by first using a wide-field camera to detect initial illumination from the airborne beacon, and to perform coarse pointing. It then transfers control to a high-precision pointing detector. Using this scheme, live video was successfully streamed from the ground to the aircraft at 270 Mb/s while simultaneously downlinking a 50 kb/s data stream from the aircraft to the ground.

  3. Airborne myxomycete spores: detection using molecular techniques

    NASA Astrophysics Data System (ADS)

    Kamono, Akiko; Kojima, Hisaya; Matsumoto, Jun; Kawamura, Kimitaka; Fukui, Manabu

    2009-01-01

    Myxomycetes are organisms characterized by a life cycle that includes a fruiting body stage. Myxomycete fruiting bodies contain spores, and wind dispersal of the spores is considered important for this organism to colonize new areas. In this study, the presence of airborne myxomycetes and the temporal changes in the myxomycete composition of atmospheric particles (aerosols) were investigated with a polymerase chain reaction (PCR)-based method for Didymiaceae and Physaraceae. Twenty-one aerosol samples were collected on the roof of a three-story building located in Sapporo, Hokkaido Island, northern Japan. PCR analysis of DNA extracts from the aerosol samples indicated the presence of airborne myxomycetes in all the samples, except for the one collected during the snowfall season. Denaturing gradient gel electrophoresis (DGGE) analysis of the PCR products showed seasonally varying banding patterns. The detected DGGE bands were subjected to sequence analyses, and four out of nine obtained sequences were identical to those of fruiting body samples collected in Hokkaido Island. It appears that the difference in the fruiting period of each species was correlated with the seasonal changes in the myxomycete composition of the aerosols. Molecular evidence shows that newly formed spores are released and dispersed in the air, suggesting that wind-driven dispersal of spores is an important process in the life history of myxomycetes. This study is the first to detect airborne myxomycetes with the use of molecular ecological analyses and to characterize their seasonal distribution.

  4. Airborne Tactical Free-Electron Laser

    SciTech Connect

    Whitney, Roy; Neil, George

    2007-02-01

    The goal of 100 kilowatts (kW) of directed energy from an airborne tactical platform has proved challenging due to the size and weight of most of the options that have been considered. However, recent advances in Free-Electron Lasers appear to offer a solution along with significant tactical advantages: a nearly unlimited magazine, time structures for periods from milliseconds to hours, radar like functionality, and the choice of the wavelength of light that best meets mission requirements. For an Airborne Tactical Free-Electron Laser (ATFEL) on a platforms such as a Lockheed C-130J-30 and airships, the two most challenging requirements, weight and size, can be met by generating the light at a higher harmonic, aggressively managing magnet weights, managing cryogenic heat loads using recent SRF R&D results, and using FEL super compact design concepts that greatly reduce the number of components. The initial R&D roadmap for achieving an ATFEL is provided in this paper. Performing this R&D is expected to further reduce the weight, size and power requirements for the FELs the Navy is currently developing for shipboard applications, as well as providing performance enhancements for the strategic airborne MW class FELs. The 100 kW ATFEL with its tactical advantages may prove sufficiently attractive for early advancement in the queue of deployed FELs.

  5. Airborne Infrared Spectrograph for Eclipse Observations

    NASA Astrophysics Data System (ADS)

    Golub, L.; Cheimets, P.; DeLuca, E. E.; Samra, J.; Judge, P. G.

    2015-12-01

    Direct measurements of the coronal magnetic field have significant potential to enhance our understanding of coronal dynamics, and improve forecasting models. Of particular interest are observations of coronal field lines in the Transition Corona, the transitional region between closed and open flux systems, providing important information on eruptive instabilities and on the origin of the slow solar wind. While current instruments routinely observe the photospheric and chromospheric magnetic fields, the proposed airborne spectrometer will take a step toward the direct observation of coronal fields by measuring plasma emission in the infrared at high spatial and spectral resolution. The targeted lines are five forbidden magnetic dipole transitions between 1.4 and 4 um. The airborne system will consist of a telescope, grating spectrometer and pointing/stabilization system to be flown on the NSF/NCAR High-performance Instrumented Airborne Platform for Environmental Research (HIAPER) during the 21 August 2017 total solar eclipse. We will discuss the scientific objectives of the 2017 flight, describe details of the instrument design, and present the observing program for the eclipse.

  6. Repeated Sprints: An Independent Not Dependent Variable.

    PubMed

    Taylor, Jonathan M; Macpherson, Tom W; Spears, Iain R; Weston, Matthew

    2016-07-01

    The ability to repeatedly perform sprints has traditionally been viewed as a key performance measure in team sports, and the relationship between repeated-sprint ability (RSA) and performance has been explored extensively. However, when reviewing the repeated-sprint profile of team-sports match play it appears that the occurrence of repeated-sprint bouts is sparse, indicating that RSA is not as important to performance as commonly believed. Repeated sprints are, however, a potent and time-efficient training strategy, effective in developing acceleration, speed, explosive leg power, aerobic power, and high-intensity-running performance--all of which are crucial to team-sport performance. As such, we propose that repeated-sprint exercise in team sports should be viewed as an independent variable (eg, a means of developing fitness) as opposed to a dependent variable (eg, a means of assessing fitness/performance). PMID:27197118

  7. Strengthening concept learning by repeated testing

    PubMed Central

    Wiklund-Hörnqvist, Carola; Jonsson, Bert; Nyberg, Lars

    2014-01-01

    The aim of this study was to examine whether repeated testing with feedback benefits learning compared to rereading of introductory psychology key-concepts in an educational context. The testing effect was examined immediately after practice, after 18 days, and at a five-week delay in a sample of undergraduate students (n = 83). The results revealed that repeated testing with feedback significantly enhanced learning compared to rereading at all delays, demonstrating that repeated retrieval enhances retention compared to repeated encoding in the short- and the long-term. In addition, the effect of repeated testing was beneficial for students irrespectively of working memory capacity. It is argued that teaching methods involving repeated retrieval are important to consider by the educational system. PMID:24313425

  8. OCULUS Sea Track Fusion Service

    NASA Astrophysics Data System (ADS)

    Panagiotou, Stylianos C.; Rizogiannis, Constantinos; Katsoulis, Stavros; Lampropoulos, Vassilis; Kanellopoulos, Sotirios; Thomopoulos, Stelios C. A.

    2015-06-01

    Oculus Sea is a complete solution regarding maritime surveillance and communications at Local as well as Central Command and Control level. It includes a robust and independent track fusion service whose main functions include: 1) Interaction with the User to suggest the fusion of two or more tracks, confirm Track ID and Vessel Metadata creation for the fused track, and suggest de-association of two tracks 2) Fusion of same vessel tracks arriving simultaneously from multiple radar sensors featuring track Association, track Fusion of associated tracks to produce a more accurate track, and Multiple tracking filters and fusion algorithms 3) Unique Track ID Generator for each fused track 4) Track Dissemination Service. Oculus Sea Track Fusion Service adopts a system architecture where each sensor is associated with a Kalman estimator/tracker that obtains an estimate of the state vector and its respective error covariance matrix. Finally, at the fusion center, association and track state estimation fusion are carried out. The expected benefits of this system include multi-sensor information fusion, enhanced spatial resolution, and improved target detection.

  9. Short Tandem Repeat DNA Internet Database

    National Institute of Standards and Technology Data Gateway

    SRD 130 Short Tandem Repeat DNA Internet Database (Web, free access)   Short Tandem Repeat DNA Internet Database is intended to benefit research and application of short tandem repeat DNA markers for human identity testing. Facts and sequence information on each STR system, population data, commonly used multiplex STR systems, PCR primers and conditions, and a review of various technologies for analysis of STR alleles have been included.

  10. Understanding and identifying amino acid repeats.

    PubMed

    Luo, Hong; Nijveen, Harm

    2014-07-01

    Amino acid repeats (AARs) are abundant in protein sequences. They have particular roles in protein function and evolution. Simple repeat patterns generated by DNA slippage tend to introduce length variations and point mutations in repeat regions. Loss of normal and gain of abnormal function owing to their variable length are potential risks leading to diseases. Repeats with complex patterns mostly refer to the functional domain repeats, such as the well-known leucine-rich repeat and WD repeat, which are frequently involved in protein–protein interaction. They are mainly derived from internal gene duplication events and stabilized by ‘gate-keeper’ residues, which play crucial roles in preventing inter-domain aggregation. AARs are widely distributed in different proteomes across a variety of taxonomic ranges, and especially abundant in eukaryotic proteins. However, their specific evolutionary and functional scenarios are still poorly understood. Identifying AARs in protein sequences is the first step for the further investigation of their biological function and evolutionary mechanism. In principle, this is an NP-hard problem, as most of the repeat fragments are shaped by a series of sophisticated evolutionary events and become latent periodical patterns. It is not possible to define a uniform criterion for detecting and verifying various repeat patterns. Instead, different algorithms based on different strategies have been developed to cope with different repeat patterns. In this review, we attempt to describe the amino acid repeat-detection algorithms currently available and compare their strategies based on an in-depth analysis of the biological significance of protein repeats. PMID:23418055

  11. Repeat topography surveys of geomorphic changes using digital surface models deriving from Formosat-2 daily revisit stereo pair with very narrow baseline

    NASA Astrophysics Data System (ADS)

    Liu, C.; Wen, H.; Liu, J.; Ko, M.; Yan, H.; Chang, L.

    2012-12-01

    Repeat topography surveys provides a geometrically-corrected frame with relief information, which is crucial for studying geomorphic changes after a major slope hazard, such as the debris flow or landslides. The successful operation of Formosat-2 has proved the concept that the temporal resolution of a remote sensing system can be much improved by deploying a high-spatial-resolution sensor in a daily revisit orbit, as each accessible scene can be systematically observed from the same angle under similar illumination conditions. These characteristics make Formosat-2 an ideal satellite for site surveillance, and its images have been successfully applied in environmental monitoring, hazard assessment, orthomap generation, rapidly responding to a global disaster event, and land use management. The attempt of using a Formosat-2 stereo pair to generate a DSM, however, has not been very successful up-to-date. Ironically, it is mainly due to the characteristics of daily-revisit orbit as well. According to the parallax equation, to obtain an accurate height estimation requires a high disparity precision from the stereo pair. The most convenient approach is to maximize the baseline B or the baseline/height (B/H) ratio to a preferred range 0.6 to 1. It is not feasible, however, to acquire an across-track stereo pair with that range of baseline from the daily-revisit orbit using Formosat-2. Even taking the orbit drifting into consideration, it would take a few months to achieve a B/H ratio of approximately 0.15 across track. Another approach is to acquire an along-track stereo pair. But for the mountainous areas, such as the central mountain areas, in Taiwan, the shaded effect and geometrically distortion are apparent. This prohibits any attempt to employ the automatic image matching technique to generate a DSM based on the disparities retrieved from Frmosat-2 along-track stereo pair directly. Phase correlation is operated in the frequency-domain, which enables the relative

  12. Dual-Frequency Airborne Scanning Rain Radar Antenna System

    NASA Technical Reports Server (NTRS)

    Hussein, Ziad A.; Green, Ken

    2004-01-01

    A compact, dual-frequency, dual-polarization, wide-angle-scanning antenna system has been developed as part of an airborne instrument for measuring rainfall. This system is an upgraded version of a prior single-frequency airborne rain radar antenna system and was designed to satisfy stringent requirements. One particularly stringent combination of requirements is to generate two dual-polarization (horizontal and vertical polarizations) beams at both frequencies (13.405 and 35.605 GHz) in such a way that the beams radiated from the antenna point in the same direction, have 3-dB angular widths that match within 25 percent, and have low sidelobe levels over a wide scan angle at each polarization-and-frequency combination. In addition, the system is required to exhibit low voltage standing-wave ratios at both frequencies. The system (see figure) includes a flat elliptical scanning reflector and a stationary offset paraboloidal reflector illuminated by a common-aperture feed system that comprises a corrugated horn with four input ports one port for each of the four frequency-and-polarization combinations. The feed horn is designed to simultaneously (1) under-illuminate the reflectors 35.605 GHz and (2) illuminate the reflectors with a 15-dB edge taper at 13.405 GHz. The scanning mirror is rotated in azimuth to scan the antenna beam over an angular range of 20 in the cross-track direction for wide swath coverage, and in elevation to compensate for the motion of the aircraft. The design of common-aperture feed horn makes it possible to obtain the required absolute gain and low side-lobe levels in wide-angle beam scanning. The combination of the common-aperture feed horn with the small (0.3) focal-length-to-diameter ratio of the paraboloidal reflector makes it possible for the overall system to be compact enough that it can be mounted on a DC-8 airplane.

  13. Overview of the Airborne Tropical TRopopause EXperiment (ATTREX)

    NASA Technical Reports Server (NTRS)

    Jensen, Eric

    2015-01-01

    The NASA Airborne Tropical TRopopause EXperiment (ATTREX) is a series of airborne campaigns focused on understanding physical processes in the Tropical Tropopause Layer (TTL) and their role in atmospheric chemistry and climate. ATTREX is using the high-altitude, long-duration NASA Global Hawk Unmanned Air System to make in situ and remote-sensing measurements spanning the Pacific. A particular ATTREX emphasis is to better understand the dehydration of air as it passes through the cold tropical tropopause region. The ATTREX payload contains 12 in situ and remote sensing instruments that measure water vapor, clouds, multiple gaseous tracers (CO, CO2, CH4, NMHC, SF6, CFCs, N2O), reactive chemical compounds (O3, BrO, NO2), meteorological parameters, and radiative fluxes. ATTREX flight series have been conducted in the fall of 2011 from Armstrong Flight Research Center (AFRC) in California, in the winter of 2013 from AFRC, and in the winter/spring of 2014 from Guam. The first two flight series provided extensive sampling of the central and eastern Pacific, whereas the last flight series permitted sampling in the western Pacific. The sampling strategy has primarily involved repeated ascents and descents through the depth of the TTL (about 13-19 km). Over 100 TTL profiles were obtained on each flight series. The ATTREX dataset includes TTL water vapor measurements with unprecedented accuracy, ice crystal size distributions and habits. The cloud and water measurements provide unique information about TTL cloud formation, the persistence of super-saturation with respect to ice, and dehydration. The plethora of tracers measured on the Global Hawk flights are providing unique information about TTL transport pathways and time scales. The meteorological measurements are revealing dynamical phenomena controlling the TTL thermal structure, and the radiation measurements are providing information about heating rates associated with TTL clouds and water vapor. This presentation

  14. Overview of the Airborne Tropical TRopopause EXperiment (ATTREX)

    NASA Astrophysics Data System (ADS)

    Singh, H. B.; Jensen, E. J.; Pfister, L.

    2014-12-01

    The NASA Airborne Tropical TRopopause EXperiment (ATTREX) is a series of airborne campaigns focused on understanding physical processes in the Tropical Tropopause Layer (TTL) and their role in atmospheric chemistry and climate. ATTREX is using the high-altitude, long-duration NASA Global Hawk Unmanned Air System to make in situ and remote-sensing measurements spanning the Pacific. A particular ATTREX emphasis is to better understand the dehydration of air as it passes through the cold tropical tropopause region. The ATTREX payload contains 12 in situ and remote sensing instruments that measure water vapor, clouds, multiple gaseous tracers (CO, CO2, CH4, NMHC, SF6, CFCs, N2O), reactive chemical compounds (O3, BrO, NO2), meteorological parameters, and radiative fluxes.ATTREX flight series have been conducted in the fall of 2011 from Armstrong Flight Research Center (AFRC) in California, in the winter of 2013 from AFRC, and in the winter/spring of 2014 from Guam. The first two flight series provided extensive sampling of the central and eastern Pacific, whereas the last flight series permitted sampling in the western Pacific. The sampling strategy has primarily involved repeated ascents and descents through the depth of the TTL (about 13-19 km). Over 100 TTL profiles were obtained on each flight series. The ATTREX dataset includes TTL water vapor measurements with unprecedented accuracy, ice crystal size distributions and habits. The cloud and water measurements provide unique information about TTL cloud formation, the persistence of supersaturation with respect to ice, and dehydration. The plethora of tracers measured on the Global Hawk flights are providing unique information about TTL transport pathways and time scales. The meteorological measurements are revealing dynamical phenomena controlling the TTL thermal structure, and the radiation measurements are providing information about heating rates associated with TTL clouds and water vapor.This presentation will

  15. AIDA - from Airborne Data Inversion to In-Depth Analysis

    NASA Astrophysics Data System (ADS)

    Meyer, U.; Goetze, H.; Schroeder, M.; Boerner, R.; Tezkan, B.; Winsemann, J.; Siemon, B.; Alvers, M.; Stoll, J. B.

    2011-12-01

    The rising competition in land use especially between water economy, agriculture, forestry, building material economy and other industries often leads to irreversible deterioration in the water and soil system (as salinization and degradation) which results in a long term damage of natural resources. A sustainable exploitation of the near subsurface by industry, economy and private households is a fundamental demand of a modern society. To fulfill this demand, a sound and comprehensive knowledge on structures and processes of the near subsurface is an important prerequisite. A spatial survey of the usable underground by aerogeophysical means and a subsequent ground geophysics survey targeted at special locations will deliver essential contributions within short time that make it possible to gain the needed additional knowledge. The complementary use of airborne and ground geophysics as well as the validation, assimilation and improvement of current findings by geological and hydrogeological investigations and plausibility tests leads to the following key questions: a) Which new and/or improved automatic algorithms (joint inversion, data assimilation and such) are useful to describe the structural setting of the usable subsurface by user specific characteristics as i.e. water volume, layer thicknesses, porosities etc.? b) What are the physical relations of the measured parameters (as electrical conductivities, magnetic susceptibilities, densities, etc.)? c) How can we deduce characteristics or parameters from the observations which describe near subsurface structures as ground water systems, their charge, discharge and recharge, vulnerabilities and other quantities? d) How plausible and realistic are the numerically obtained results in relation to user specific questions and parameters? e) Is it possible to compile material flux balances that describe spatial and time dependent impacts of environmental changes on aquifers and soils by repeated airborne surveys? In

  16. Lambda Exonuclease Digestion of CGG Trinucleotide Repeats

    PubMed Central

    Conroy, R.S.; Koretsky, A.P.; Moreland, J.

    2011-01-01

    Fragile X syndrome and other triplet repeat diseases are characterized by an elongation of a repeating DNA triplet. The ensemble-averaged lambda exonuclease digestion rate of different substrates, including one with an elongated FMR1 gene containing 120 CGG repeats, was measured using absorption and fluorescence spectroscopy. Using magnetic tweezers sequence-dependent digestion rates and pausing was measured for individual lambda exonucleases. Within the triplet repeats a lower average and narrower distribution of rates and a higher frequency of pausing was observed. PMID:19562332

  17. Approaching improved adhesive bonding repeatability

    NASA Astrophysics Data System (ADS)

    Schlette, Christian; Müller, Tobias; Roβmann, Jürgen; Brecher, Christian

    2016-03-01

    Today, the precision of micro-optics assembly is mostly limited by the accuracy of the bonding process ― and in the case of adhesive bonding by the prediction and compensation of adhesive shrinkage during curing. In this contribution, we present a novel approach to address adhesive bonding based on hybrid control system theory. In hybrid control, dynamic systems are described as "plants" which produce discrete and/or continuous outputs from given discrete and/or continuous inputs, thus yielding a hybrid state space description of the system. The task of hybrid controllers is to observe the plant and to generate a discrete and/or continuous input sequence that guides or holds the plant in a desired target state region while avoiding invalid or unwanted intermediate states. Our approach is based on a series of experiments carried out in order to analyze, define and decouple the dependencies of adhesive shrinkage on multiple parameters, such as application geometries, fixture forces and UV intensities. As some of the dependencies describe continuous effects (e.g. shrinkage from UV intensity) and other dependencies describe discrete state transitions (e.g. fixture removal during curing), the resulting model of the overall bonding process is a hybrid dynamic system in the general case. For this plant model, we then propose a concept of sampling-based parameter search as a basis to design suitable hybrid controllers, which have the potential to optimize process control for a selection of assembly steps, thus improving the repeatability of related production steps like beam-shaping optics or mounting of turning mirrors for fiber coupling.

  18. Laboratory test results of the high speed optical tracking system for the Spaceborne Geodynamic Ranging System

    NASA Astrophysics Data System (ADS)

    Zagwodzki, Thomas W.; White, David L.

    1987-02-01

    The high speed, high resolution optical tracking system for the Spaceborne Geodynamic Ranging System employs a two-axis gimbaled pointing device that can operate from a Space Shuttle platform and can track multiple retroreflector ground targets with arcsec accuracy. Laboratory tests of the stepping characteristics of the pointing system for various step sizes and directions has shown arcsec repeatability with little wasted motion, overshoot, or ringing. The worst rms tracking jitter was 1 and 2 arcsec in the roll and pitch axes, respectively, at the maximum tracking rate of 2 deg/sec.

  19. Laboratory test results of the high speed optical tracking system for the Spaceborne Geodynamic Ranging System

    NASA Technical Reports Server (NTRS)

    Zagwodzki, Thomas W.; White, David L.

    1987-01-01

    The high speed, high resolution optical tracking system for the Spaceborne Geodynamic Ranging System employs a two-axis gimbaled pointing device that can operate from a Space Shuttle platform and can track multiple retroreflector ground targets with arcsec accuracy. Laboratory tests of the stepping characteristics of the pointing system for various step sizes and directions has shown arcsec repeatability with little wasted motion, overshoot, or ringing. The worst rms tracking jitter was 1 and 2 arcsec in the roll and pitch axes, respectively, at the maximum tracking rate of 2 deg/sec.

  20. Coordinated Airborne, Spaceborne, and Ground-Based Measurements of Massive, Thick Aerosol Layers During the Dry Season in Southern Africa

    NASA Technical Reports Server (NTRS)

    Schmid, B.; Redemann, J.; Russell, P. B.; Hobbs, P. V.; Hlavka, D. L.; McGill, M. J.; Holben, B. N.; Welton, E. J.; Campbell, J.; Torres, O.; Hipskind, R. Stephen (Technical Monitor)

    2002-01-01

    During the dry-season airborne campaign of the Southern African Regional Science Initiative (SAFARI 2000), unique coordinated observations were made of massive, thick aerosol layers. These layers were often dominated by aerosols from biomass burning. We report on airborne Sunphotometer measurements of aerosol optical depth (lambda=354-1558 nm), columnar water vapor, and vertical profiles of aerosol extinction and water vapor density that were obtained aboard the University of Washington's Convair-580 research aircraft. We compare these with ground-based AERONET Sun/sky radiometer results, with ground based lidar data MPL-Net), and with measurements from a downward-pointing lidar aboard the high-flying NASA ER-2 aircraft. Finally, we show comparisons between aerosol optical depths from the Sunphotometer and those retrieved over land and over water using four spaceborne sensors (TOMS (Total Ozone Mapping Spectrometer), MODIS (Moderate Resolution Imaging Spectrometer), MISR (Multiangle Imaging Spectroradiometer) and ATSR-2 (Along Track Scanning Radiometer)).