Airframe noise: A design and operating problem

NASA Technical Reports Server (NTRS)

Hardin, J. C.

1976-01-01

A critical assessment of the state of the art in airframe noise is presented. Full-scale data on the intensity, spectra, and directivity of this noise source are evaluated in light of the comprehensive theory developed by Ffowcs Williams and Hawkings. Vibration of panels on the aircraft is identified as a possible additional source of airframe noise. The present understanding and methods for prediction of other component sources - airfoils, struts, and cavities - are discussed. Operating problems associated with airframe noise as well as potential design methods for airframe noise reduction are identified.

Airframe Noise Studies: Review and Future Direction

NASA Technical Reports Server (NTRS)

Rackl, Robert G.; Miller, Gregory; Guo, Yueping; Yamamoto, Kingo

2005-01-01

This report contains the following information: 1) a review of airframe noise research performed under NASA's Advanced Subsonic Transport (AST) program up to the year 2000, 2) a comparison of the year 1992 airframe noise predictions with those using a year 2000 baseline, 3) an assessment of various airframe noise reduction concepts as applied to the year 2000 baseline predictions, and 4) prioritized recommendations for future airframe noise reduction work. NASA's Aircraft Noise Prediction Program was the software used for all noise predictions and assessments. For future work, the recommendations for the immediate future focus on the development of design tools sensitive to airframe noise treatment effects and on improving the basic understanding of noise generation by the landing gear as well as on its reduction.

Propulsion and airframe aerodynamic interactions of supersonic V/STOL configurations. Volume 4: Summary

NASA Technical Reports Server (NTRS)

Zilz, D. E.; Wallace, H. W.; Hiley, P. E.

1985-01-01

A wind tunnel model of a supersonic V/STOL fighter configuration has been tested to measure the aerodynamic interaction effects which can result from geometrically close-coupled propulsion system/airframe components. The approach was to configure the model to represent two different test techniques. One was a conventional test technique composed of two test modes. In the Flow-Through mode, absolute configuration aerodynamics are measured, including inlet/airframe interactions. In the Jet-Effects mode, incremental nozzle/airframe interactions are measured. The other test technique is a propulsion simulator approach, where a sub-scale, externally powered engine is mounted in the model. This allows proper measurement of inlet/airframe and nozzle/airframe interactions simultaneously. This is Volume 4 of 4: Final Report- Summary.

Investigation on the use of optimization techniques for helicopter airframe vibrations design studies

NASA Technical Reports Server (NTRS)

Sreekanta Murthy, T.

1992-01-01

Results of the investigation of formal nonlinear programming-based numerical optimization techniques of helicopter airframe vibration reduction are summarized. The objective and constraint function and the sensitivity expressions used in the formulation of airframe vibration optimization problems are presented and discussed. Implementation of a new computational procedure based on MSC/NASTRAN and CONMIN in a computer program system called DYNOPT for optimizing airframes subject to strength, frequency, dynamic response, and dynamic stress constraints is described. An optimization methodology is proposed which is thought to provide a new way of applying formal optimization techniques during the various phases of the airframe design process. Numerical results obtained from the application of the DYNOPT optimization code to a helicopter airframe are discussed.

Propulsion and airframe aerodynamic interactions of supersonic V/STOL configurations. Volume 1: Wind tunnel test pressure data report

NASA Technical Reports Server (NTRS)

Zilz, D. E.; Devereaux, P. A.

1985-01-01

A wind tunnel model of a supersonic V/STOL fighter configuration has been tested to measure the aerodynamic interaction effects which can result from geometrically close-coupled propulsion system/airframe components. The approach was to configure the model to represent two different test techniques. One was a conventional test technique composed of two test modes. In the Flow-Through mode, absolute configuration aerodynamics are measured, including inlet/airframe interactions. In the Jet-Effects mode, incremental nozzle/airframe interactions are measured. The other test technique is a propulsion simulator approach, where a sub-scale, externally powered engine is mounted in the model. This allows proper measurement of inlet/airframe and nozzle/airframe interactions simultaneously. This is Volume 1 of 2: Wind Tunnel Test Pressure Data Report.

Proceedings of the Airframe Icing Workshop

NASA Technical Reports Server (NTRS)

Colantonio, Ron O. (Editor)

2009-01-01

The NASA Glenn Research Center (GRC) has a long history of working with its partners towards the understanding of ice accretion formation and its associated degradation of aerodynamic performance. The June 9, 2009, Airframe Icing Workshop held at GRC provided an opportunity to examine the current NASA airframe icing research program and to dialogue on remaining and emerging airframe icing issues and research with the external community. Some of the airframe icing gaps identified included, but are not limited to, ice accretion simulation enhancements, three-dimensional benchmark icing database development, three-dimensional iced aerodynamics modeling, and technology development for a smart icing system.

Airframe/TPS Session

NASA Technical Reports Server (NTRS)

Welch, Sharon; Bowles, David

2000-01-01

This viewgraph presentation gives an overview of the second generation Reusable Launch Vehicle (RLV) airframe configuration, including details on the structures and materials, tanks, airframe/cryotank demonstrations, internal assemblies, weight growth and margin, and safety and cost requirements.

Propulsion and airframe aerodynamic interactions of supersonic V/STOL configurations. Volume 2: Wind tunnel test force and moment data report

NASA Technical Reports Server (NTRS)

Zilz, D. E.

1985-01-01

A wind tunnel model of a supersonic V/STOL fighter configuration has been tested to measure the aerodynamic interaction effects which can result from geometrically close-coupled propulsion system/airframe components. The approach was to configure the model to represent two different test techniques. One was a conventional test technique composed of two test modes. In the Flow-Through mode, absolute configuration aerodynamics are measured, including inlet/airframe interactions. In the Jet-Effects mode, incremental nozzle/airframe interactions are measured. The other test technique is a propulsion simulator approach, where a sub-scale, externally powered engine is mounted in the model. This allows proper measurement of inlet/airframe and nozzle/airframe interactions simultaneously. This is Volume 2 of 2: Wind Tunnel Test Force and Moment Data Report.

Integrating CFD, CAA, and Experiments Towards Benchmark Datasets for Airframe Noise Problems

NASA Technical Reports Server (NTRS)

Choudhari, Meelan M.; Yamamoto, Kazuomi

2012-01-01

Airframe noise corresponds to the acoustic radiation due to turbulent flow in the vicinity of airframe components such as high-lift devices and landing gears. The combination of geometric complexity, high Reynolds number turbulence, multiple regions of separation, and a strong coupling with adjacent physical components makes the problem of airframe noise highly challenging. Since 2010, the American Institute of Aeronautics and Astronautics has organized an ongoing series of workshops devoted to Benchmark Problems for Airframe Noise Computations (BANC). The BANC workshops are aimed at enabling a systematic progress in the understanding and high-fidelity predictions of airframe noise via collaborative investigations that integrate state of the art computational fluid dynamics, computational aeroacoustics, and in depth, holistic, and multifacility measurements targeting a selected set of canonical yet realistic configurations. This paper provides a brief summary of the BANC effort, including its technical objectives, strategy, and selective outcomes thus far.

Airframe self-noise: Four years of research. [aircraft noise reduction for commercial aircraft

NASA Technical Reports Server (NTRS)

Hardin, J. C.

1976-01-01

A critical assessment of the state of the art in airframe self-noise is presented. Full-scale data on the intensity, spectra and directivity of this noise source are evaluated in the light of the comprehensive theory developed by Ffowcs-Williams and Hawkins. Vibration of panels on commercial aircraft is identified as a possible additional source of airframe noise. The present understanding and methods for prediction of other component sources - airfoils, struts, and cavities - are discussed, and areas for further research as well as potential methods for airframe noise reduction are identified. Finally, the various experimental methods which have been developed for airframe noise research are discussed and sample results are presented.

Life cycle cost analysis of aging aircraft airframe maintenance

NASA Astrophysics Data System (ADS)

Sperry, Kenneth Robert

Scope and method of study. The purpose of this study was to examine the relationship between an aircraft's age and its annual airframe maintenance costs. Common life cycle costing methodology has previously not recognized the existence of this cost growth potential, and has therefor not determined the magnitude nor significance of this cost element. This study analyzed twenty-five years of DOT Form 41-airframe maintenance cost data for the Boeing 727, 737, 747 and McDonnell Douglas DC9 and DC-10 aircraft. Statistical analysis included regression analysis, Pearson's r, and t-tests to test the null hypothesis. Findings and conclusion. Airframe maintenance cost growth was confirmed to be increasing after an aircraft's age exceeded its designed service objective of approximately twenty-years. Annual airframe maintenance cost growth increases were measured ranging from 3.5% annually for a DC-9, to approximately 9% annually for a DC-10 aircraft. Average measured coefficient of determination between age and airframe maintenance, exceeded .80, confirming a strong relationship between cost: and age. The statistical significance of the difference between airframe costs sampled in 1985, compared to airframe costs sampled in 1998 was confirmed by t-tests performed on each subject aircraft group. Future cost forecasts involving aging aircraft subjects must address cost growth due to aging when attempting to model an aircraft's economic service life.

Aircraft Noise Reduction Subproject Overview

NASA Technical Reports Server (NTRS)

Fernandez, Hamilton; Nark, Douglas M.; Van Zante, Dale E.

2016-01-01

The material presents highlights of propulsion and airframe noise research being completed for the Advanced Air Transport Technology Project. The basis of noise reduction plans along with representative work for the airframe, propulsion, and propulsion-airframe integration is discussed for the Aircraft Noise reduction Subproject.

Explosively activated egress area

NASA Technical Reports Server (NTRS)

Bement, L. J.; Bailey, J. W. (Inventor)

1983-01-01

A lightweight, add on structure which employs linear shaped pyrotechnic charges to smoothly cut an airframe along an egress area periphery is provided. It compromises reaction surfaces attached to the exterior surface of the airframe's skin and is designed to restrict the skin deflection. That portion of the airframe within the egress area periphery is jettisoned. Retention surfaces and sealing walls are attached to the interior surface of the airframe's skin and are designed to shield the interior of the aircraft during detonation of the pyrotechnic charges.

14 CFR 135.439 - Maintenance recording requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

..., propeller, and rotor. (ii) The current status of life-limited parts of each airframe, engine, propeller... alterations and repairs to each airframe, engine, propeller, rotor, and appliance. (b) Each certificate holder... the records of the last complete overhaul of each airframe, engine, propeller, rotor, and appliance...

14 CFR 135.439 - Maintenance recording requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

..., propeller, and rotor. (ii) The current status of life-limited parts of each airframe, engine, propeller... alterations and repairs to each airframe, engine, propeller, rotor, and appliance. (b) Each certificate holder... the records of the last complete overhaul of each airframe, engine, propeller, rotor, and appliance...

14 CFR 135.439 - Maintenance recording requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

..., propeller, and rotor. (ii) The current status of life-limited parts of each airframe, engine, propeller... alterations and repairs to each airframe, engine, propeller, rotor, and appliance. (b) Each certificate holder... the records of the last complete overhaul of each airframe, engine, propeller, rotor, and appliance...

14 CFR 135.439 - Maintenance recording requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

..., propeller, and rotor. (ii) The current status of life-limited parts of each airframe, engine, propeller... alterations and repairs to each airframe, engine, propeller, rotor, and appliance. (b) Each certificate holder... the records of the last complete overhaul of each airframe, engine, propeller, rotor, and appliance...

14 CFR 135.439 - Maintenance recording requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

..., propeller, and rotor. (ii) The current status of life-limited parts of each airframe, engine, propeller... alterations and repairs to each airframe, engine, propeller, rotor, and appliance. (b) Each certificate holder... the records of the last complete overhaul of each airframe, engine, propeller, rotor, and appliance...

14 CFR 121.321 - Operations in icing.

Code of Federal Regulations, 2014 CFR

2014-01-01

.... (1) The airplane must be equipped with a certificated primary airframe ice detection system. (i) The airframe ice protection system must be activated automatically, or manually by the flightcrew, when the primary ice detection system indicates activation is necessary. (ii) When the airframe ice protection...

Analysis of airframe/engine interactions in integrated flight and propulsion control

NASA Technical Reports Server (NTRS)

Schierman, John D.; Schmidt, David K.

1991-01-01

An analysis framework for the assessment of dynamic cross-coupling between airframe and engine systems from the perspective of integrated flight/propulsion control is presented. This analysis involves to determining the significance of the interactions with respect to deterioration in stability robustness and performance, as well as critical frequency ranges where problems may occur due to these interactions. The analysis illustrated here investigates both the airframe's effects on the engine control loops and the engine's effects on the airframe control loops in two case studies. The second case study involves a multi-input/multi-output analysis of the airframe. Sensitivity studies are performed on critical interactions to examine the degradations in the system's stability robustness and performance. Magnitudes of the interactions required to cause instabilities, as well as the frequencies at which the instabilities occur are recorded. Finally, the analysis framework is expanded to include control laws which contain cross-feeds between the airframe and engine systems.

Airframe Research and Technology for Hypersonic Airbreathing Vehicles

NASA Technical Reports Server (NTRS)

Glass, David E.; Merski, N. Ronald; Glass, Christopher E.

2002-01-01

The Hypersonics Investment Area (HIA) within NASA's Advanced Space Transportation Program (ASTP) has the responsibility to develop hypersonic airbreathing vehicles for access to space. The Airframe Research and Technology (AR and T) Project, as one of six projects in the HIA, will push the state-of-the-art in airframe and vehicle systems for low-cost, reliable, and safe space transportation. The individual technologies within the project are focused on advanced, breakthrough technologies in airframe and vehicle systems and cross-cutting activities that are the basis for improvements in these disciplines. Both low and medium technology readiness level (TRL) activities are being pursued. The key technical areas that will be addressed by the project include analysis and design tools, integrated vehicle health management (IVHM), composite (polymer, metal, and ceramic matrix) materials development, thermal/structural wall concepts, thermal protection systems, seals, leading edges, aerothermodynamics, and airframe/propulsion flowpath technology. Each of the technical areas or sub-projects within the Airframe R and T Project is described in this paper.

14 CFR 91.1439 - CAMP: Maintenance recording requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... service of the airframe, engine, propeller, and rotor. (ii) The current status of life-limited parts of each airframe, engine, propeller, rotor, and appliance. (iii) The time since last overhaul of each item... required. (vi) A list of current major alterations and repairs to each airframe, engine, propeller, rotor...

14 CFR 91.1439 - CAMP: Maintenance recording requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... service of the airframe, engine, propeller, and rotor. (ii) The current status of life-limited parts of each airframe, engine, propeller, rotor, and appliance. (iii) The time since last overhaul of each item... required. (vi) A list of current major alterations and repairs to each airframe, engine, propeller, rotor...

14 CFR 91.1439 - CAMP: Maintenance recording requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... service of the airframe, engine, propeller, and rotor. (ii) The current status of life-limited parts of each airframe, engine, propeller, rotor, and appliance. (iii) The time since last overhaul of each item... required. (vi) A list of current major alterations and repairs to each airframe, engine, propeller, rotor...

14 CFR 91.1439 - CAMP: Maintenance recording requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... service of the airframe, engine, propeller, and rotor. (ii) The current status of life-limited parts of each airframe, engine, propeller, rotor, and appliance. (iii) The time since last overhaul of each item... required. (vi) A list of current major alterations and repairs to each airframe, engine, propeller, rotor...

14 CFR 91.1439 - CAMP: Maintenance recording requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... service of the airframe, engine, propeller, and rotor. (ii) The current status of life-limited parts of each airframe, engine, propeller, rotor, and appliance. (iii) The time since last overhaul of each item... required. (vi) A list of current major alterations and repairs to each airframe, engine, propeller, rotor...

Aviation Maintenance Technology. Airframe. A201. Airframe Structures and Non-Metallic Structural Repairs. Instructor Material.

ERIC Educational Resources Information Center

Oklahoma State Board of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This teacher's guide is designed to aid teachers in leading students through a module on airframe structures and nonmetallic structural repairs. The module contains four units that cover the following topics: (1) identifying aerodynamic and construction characteristics of aircraft structures; (2) inspecting wooden structures; (3) inspecting and…

The NASA/Industry Design Analysis Methods for Vibrations (DAMVIBS) Program - A government overview. [of rotorcraft technology development using finite element method

NASA Technical Reports Server (NTRS)

Kvaternik, Raymond G.

1992-01-01

An overview is presented of government contributions to the program called Design Analysis Methods for Vibrations (DAMV) which attempted to develop finite-element-based analyses of rotorcraft vibrations. NASA initiated the program with a finite-element modeling program for the CH-47D tandem-rotor helicopter. The DAMV program emphasized four areas including: airframe finite-element modeling, difficult components studies, coupled rotor-airframe vibrations, and airframe structural optimization. Key accomplishments of the program include industrywide standards for modeling metal and composite airframes, improved industrial designs for vibrations, and the identification of critical structural contributors to airframe vibratory responses. The program also demonstrated the value of incorporating secondary modeling details to improving correlation, and the findings provide the basis for an improved finite-element-based dynamics design-analysis capability.

Airframe Noise Sub-Component Definition and Model

NASA Technical Reports Server (NTRS)

Golub, Robert A. (Technical Monitor); Sen, Rahul; Hardy, Bruce; Yamamoto, Kingo; Guo, Yue-Ping; Miller, Gregory

2004-01-01

Both in-house, and jointly with NASA under the Advanced Subsonic Transport (AST) program, Boeing Commerical Aircraft Company (BCA) had begun work on systematically identifying specific components of noise responsible for total airframe noise generation and applying the knowledge gained towards the creation of a model for airframe noise prediction. This report documents the continuation of the collection of database from model-scale and full-scale airframe noise measurements to compliment the earlier existing databases, the development of the subcomponent models and the generation of a new empirical prediction code. The airframe subcomponent data includes measurements from aircraft ranging in size from a Boeing 737 to aircraft larger than a Boeing 747 aircraft. These results provide the continuity to evaluate the technology developed under the AST program consistent with the guidelines set forth in NASA CR-198298.

Three-dimensional calculations of rotor-airframe interaction in forward flight

NASA Technical Reports Server (NTRS)

Zori, Laith A. J.; Mathur, Sanjay R.; Rajagopalan, R. G.

1992-01-01

A method for analyzing the mutual aerodynamic interaction between a rotor and an airframe model has been developed. This technique models the rotor implicitly through the source terms of the momentum equations. A three-dimensional, incompressible, laminar, Navier-Stokes solver in cylindrical coordinates was developed for analyzing the rotor/airframe problem. The calculations are performed on a simplified model at an advance ratio of 0.1. The airframe surface pressure predictions are found to be in good agreement with wind tunnel test data. Results are presented for velocity and pressure field distributions in the wake of the rotor.

Correlation of AH-1G airframe test data with a NASTRAN mathematical model

NASA Technical Reports Server (NTRS)

Cronkhite, J. D.; Berry, V. L.

1976-01-01

Test data was provided for evaluating a mathematical vibration model of the Bell AH-1G helicopter airframe. The math model was developed and analyzed using the NASTRAN structural analysis computer program. Data from static and dynamic tests were used for comparison with the math model. Static tests of the fuselage and tailboom were conducted to verify the stiffness representation of the NASTRAN model. Dynamic test data were obtained from shake tests of the airframe and were used to evaluate the NASTRAN model for representing the low frequency (below 30 Hz) vibration response of the airframe.

Airframe noise prediction evaluation

NASA Technical Reports Server (NTRS)

Yamamoto, Kingo J.; Donelson, Michael J.; Huang, Shumei C.; Joshi, Mahendra C.

1995-01-01

The objective of this study is to evaluate the accuracy and adequacy of current airframe noise prediction methods using available airframe noise measurements from tests of a narrow body transport (DC-9) and a wide body transport (DC-10) in addition to scale model test data. General features of the airframe noise from these aircraft and models are outlined. The results of the assessment of two airframe prediction methods, Fink's and Munson's methods, against flight test data of these aircraft and scale model wind tunnel test data are presented. These methods were extensively evaluated against measured data from several configurations including clean, slat deployed, landing gear-deployed, flap deployed, and landing configurations of both DC-9 and DC-10. They were also assessed against a limited number of configurations of scale models. The evaluation was conducted in terms of overall sound pressure level (OASPL), tone corrected perceived noise level (PNLT), and one-third-octave band sound pressure level (SPL).

Airframe-Jet Engine Integration Noise

NASA Technical Reports Server (NTRS)

Tam, Christopher; Antcliff, Richard R. (Technical Monitor)

2003-01-01

It has been found experimentally that the noise radiated by a jet mounted under the wing of an aircraft exceeds that of the same jet in a stand-alone environment. The increase in noise is referred to as jet engine airframe integration noise. The objectives of the present investigation are, (1) To obtain a better understanding of the physical mechanisms responsible for jet engine airframe integration noise or installation noise. (2) To develop a prediction model for jet engine airframe integration noise. It is known that jet mixing noise consists of two principal components. They are the noise from the large turbulence structures of the jet flow and the noise from the fine scale turbulence. In this investigation, only the effect of jet engine airframe interaction on the fine scale turbulence noise of a jet is studied. The fine scale turbulence noise is the dominant noise component in the sideline direction. Thus we limit out consideration primarily to the sideline.

Status of ERA Airframe Technology Demonstrators

NASA Technical Reports Server (NTRS)

Davis, Pamela; Jegley, Dawn; Rigney, Tom

2015-01-01

NASA has created the Environmentally Responsible Aviation (ERA) Project to explore and document the feasibility, benefits and technical risk of advanced vehicle configurations and enabling technologies that will reduce the impact of aviation on the environment. A critical aspect of this pursuit is the development of a lighter, more robust airframe that will enable the introduction of unconventional aircraft configurations that have higher lift-to-drag ratios, reduced drag, and lower community noise. The Airframe Technology subproject contains two elements. Under the Damage Arresting Composite Demonstration an advanced material system is being explored which will lead to lighter airframes that are more structural efficient than the composites used in aircraft today. Under the Adaptive Compliant Trailing Edge Flight Experiment a new concept of a flexible wing trailing edge is being evaluated which will reduce weight and improve aerodynamic performance. This presentation will describe the development these two airframe technologies.

Analysis of airframe/engine interactions - An integrated control perspective

NASA Technical Reports Server (NTRS)

Schmidt, David K.; Schierman, John D.; Garg, Sanjay

1990-01-01

Techniques for the analysis of the dynamic interactions between airframe/engine dynamical systems are presented. Critical coupling terms are developed that determine the significance of these interactions with regard to the closed loop stability and performance of the feedback systems. A conceptual model is first used to indicate the potential sources of the coupling, how the coupling manifests itself, and how the magnitudes of these critical coupling terms are used to quantify the effects of the airframe/engine interactions. A case study is also presented involving an unstable airframe with thrust vectoring for attitude control. It is shown for this system with classical, decentralized control laws that there is little airframe/engine interaction, and the stability and performance with those control laws is not affected. Implications of parameter uncertainty in the coupling dynamics is also discussed, and effects of these parameter variations are also demonstrated to be small for this vehicle configuration.

Design sensitivity analysis of rotorcraft airframe structures for vibration reduction

NASA Technical Reports Server (NTRS)

Murthy, T. Sreekanta

1987-01-01

Optimization of rotorcraft structures for vibration reduction was studied. The objective of this study is to develop practical computational procedures for structural optimization of airframes subject to steady-state vibration response constraints. One of the key elements of any such computational procedure is design sensitivity analysis. A method for design sensitivity analysis of airframes under vibration response constraints is presented. The mathematical formulation of the method and its implementation as a new solution sequence in MSC/NASTRAN are described. The results of the application of the method to a simple finite element stick model of the AH-1G helicopter airframe are presented and discussed. Selection of design variables that are most likely to bring about changes in the response at specified locations in the airframe is based on consideration of forced response strain energy. Sensitivity coefficients are determined for the selected design variable set. Constraints on the natural frequencies are also included in addition to the constraints on the steady-state response. Sensitivity coefficients for these constraints are determined. Results of the analysis and insights gained in applying the method to the airframe model are discussed. The general nature of future work to be conducted is described.

A Comparative Analysis of Two Full-Scale MD-500 Helicopter Crash Tests

NASA Technical Reports Server (NTRS)

Littell, Justin D.

2011-01-01

Two full scale crash tests were conducted on a small MD-500 helicopter at NASA Langley Research Center fs Landing and Impact Research Facility. One of the objectives of this test series was to compare airframe impact response and occupant injury data between a test which outfitted the airframe with an external composite passive energy absorbing honeycomb and a test which had no energy absorbing features. In both tests, the nominal impact velocity conditions were 7.92 m/sec (26 ft/sec) vertical and 12.2 m/sec (40 ft/sec) horizontal, and the test article weighed approximately 1315 kg (2900 lbs). Airframe instrumentation included accelerometers and strain gages. Four Anthropomorphic Test Devices were also onboard; three of which were standard Hybrid II and III, while the fourth was a specialized torso. The test which contained the energy absorbing honeycomb showed vertical impact acceleration loads of approximately 15 g, low risk for occupant injury probability, and minimal airframe damage. These results were contrasted with the test conducted without the energy absorbing honeycomb. The test results showed airframe accelerations of approximately 40 g in the vertical direction, high risk for injury probability in the occupants, and substantial airframe damage.

Open Rotor Aeroacoustic Installation Effects for Conventional and Unconventional Airframes

NASA Technical Reports Server (NTRS)

Czech, Michael J.; Thomas, Russell H.

2013-01-01

As extensive experimental campaign was performed to study the aeroacoustic installation effects of an open rotor with respect to both a conventional tube and wing type airframe and an unconventional hybrid wing body airframe. The open rotor rig had two counter rotating rows of blades each with eight blades of a design originally flight tested in the 1980s. The aeroacoustic installation effects measured in an aeroacoustic wind tunnel included those from flow effects due to inflow distortion or wake interaction and acoustic propagation effects such as shielding and reflection. The objective of the test campaign was to quantify the installation effects for a wide range of parameters and configurations derived from the two airframe types. For the conventional airframe, the open rotor was positioned in increments in front of and then over the main wing and then in positions representative of tail mounted aircraft with a conventional tail, a T-tail and a U-tail. The interaction of the wake of the open rotor as well as acoustic scattering results in an increase of about 10 dB when the rotor is positioned in front of the main wing. When positioned over the main wing a substantial amount of noise reduction is obtained and this is also observed for tail-mounted installations with a large U-tail. For the hybrid wing body airframe, the open rotor was positioned over the airframe along the centerline as well as off-center representing a twin engine location. A primary result was the documentation of the noise reduction from shielding as a function of the location of the open rotor upstream of the trailing edge of the hybrid wing body. The effects from vertical surfaces and elevon deflection were also measured. Acoustic lining was specially designed and inserted flush with the elevon and airframe surface, the result was an additional reduction in open rotor noise propagating to the far field microphones. Even with the older blade design used, the experiment provided quantification of the aeroacoustic installation effects for a wide range of open rotor and airframe configurations and can be used with data processing methods to evaluate the aeroacoustic installation effects for open rotors with modern blade designs.

Distributed Turboelectric Propulsion for Hybrid Wing Body Aircraft

NASA Technical Reports Server (NTRS)

Kim, Hyun Dae; Brown, Gerald V.; Felder, James L.

2008-01-01

Meeting future goals for aircraft and air traffic system performance will require new airframes with more highly integrated propulsion. Previous studies have evaluated hybrid wing body (HWB) configurations with various numbers of engines and with increasing degrees of propulsion-airframe integration. A recently published configuration with 12 small engines partially embedded in a HWB aircraft, reviewed herein, serves as the airframe baseline for the new concept aircraft that is the subject of this paper. To achieve high cruise efficiency, a high lift-to-drag ratio HWB was adopted as the baseline airframe along with boundary layer ingestion inlets and distributed thrust nozzles to fill in the wakes generated by the vehicle. The distributed powered-lift propulsion concept for the baseline vehicle used a simple, high-lift-capable internally blown flap or jet flap system with a number of small high bypass ratio turbofan engines in the airframe. In that concept, the engine flow path from the inlet to the nozzle is direct and does not involve complicated internal ducts through the airframe to redistribute the engine flow. In addition, partially embedded engines, distributed along the upper surface of the HWB airframe, provide noise reduction through airframe shielding and promote jet flow mixing with the ambient airflow. To improve performance and to reduce noise and environmental impact even further, a drastic change in the propulsion system is proposed in this paper. The new concept adopts the previous baseline cruise-efficient short take-off and landing (CESTOL) airframe but employs a number of superconducting motors to drive the distributed fans rather than using many small conventional engines. The power to drive these electric fans is generated by two remotely located gas-turbine-driven superconducting generators. This arrangement allows many small partially embedded fans while retaining the superior efficiency of large core engines, which are physically separated but connected through electric power lines to the fans. This paper presents a brief description of the earlier CESTOL vehicle concept and the newly proposed electrically driven fan concept vehicle, using the previous CESTOL vehicle as a baseline.

Recent advances in convectively cooled engine and airframe structures for hypersonic flight

NASA Technical Reports Server (NTRS)

Kelly, H. N.; Wieting, A. R.; Shore, C. P.; Nowak, R. J.

1978-01-01

A hydrogen-cooled structure for a fixed-geometry, airframe-integrated scramjet is described. The thermal/structural problems, concepts, design features, and technological advances are applicable to a broad range of engines. Convectively cooled airframe structural concepts that have evolved from an extensive series of investigations, the technology developments that have led to these concepts, and the benefits that accrue from their use are discussed.

14 CFR 121.363 - Responsibility for airworthiness.

Code of Federal Regulations, 2014 CFR

2014-01-01

...) The airworthiness of its aircraft, including airframes, aircraft engines, propellers, appliances, and... aircraft, including airframes, aircraft engines, propellers, appliances, emergency equipment, and parts...

14 CFR 121.363 - Responsibility for airworthiness.

Code of Federal Regulations, 2013 CFR

2013-01-01

...) The airworthiness of its aircraft, including airframes, aircraft engines, propellers, appliances, and... aircraft, including airframes, aircraft engines, propellers, appliances, emergency equipment, and parts...

14 CFR 121.363 - Responsibility for airworthiness.

Code of Federal Regulations, 2011 CFR

2011-01-01

...) The airworthiness of its aircraft, including airframes, aircraft engines, propellers, appliances, and... aircraft, including airframes, aircraft engines, propellers, appliances, emergency equipment, and parts...

14 CFR 121.363 - Responsibility for airworthiness.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) The airworthiness of its aircraft, including airframes, aircraft engines, propellers, appliances, and... aircraft, including airframes, aircraft engines, propellers, appliances, emergency equipment, and parts...

14 CFR 121.363 - Responsibility for airworthiness.

Code of Federal Regulations, 2012 CFR

2012-01-01

...) The airworthiness of its aircraft, including airframes, aircraft engines, propellers, appliances, and... aircraft, including airframes, aircraft engines, propellers, appliances, emergency equipment, and parts...

Scramjet nozzle design and analysis as applied to a highly integrated hypersonic research airplane

NASA Technical Reports Server (NTRS)

Small, W. J.; Weidner, J. P.; Johnston, P. J.

1976-01-01

Engine-nozzle airframe integration at hypersonic speeds was conducted by using a high-speed research aircraft concept as a focus. Recently developed techniques for analysis of scramjet-nozzle exhaust flows provide a realistic analysis of complex forces resulting from the engine-nozzle airframe coupling. By properly integrating the engine-nozzle propulsive system with the airframe, efficient, controlled and stable flight results over a wide speed range.

Airframe noise of the DC-9

NASA Technical Reports Server (NTRS)

Bauer, A. B.; Munson, A. G.

1977-01-01

Airframe noise measurements are reported for the DC-9-31 aircraft flown at several speeds and with a number of flap, landing gear, and slat extension configurations. The data are corrected for atmospheric attenuation and spherical divergence, and are presented for an overhead position normalized to a 1-meter height. The sound pressure levels are found to vary approximately as the fifth power of flight velocity. Both lift and drag dipoles exist as a significant part of the airframe noise. The data are compared with airframe noise predictions using the drag element and the data analysis methods. Although some of the predictions are very good, further work is needed to refine these methods, particularly for the gear-down and flaps-down configurations.

41 CFR 109-46.000-50 - Applicability.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Regulations System (Continued) DEPARTMENT OF ENERGY PROPERTY MANAGEMENT REGULATIONS UTILIZATION AND DISPOSAL... airframe structural components (except FSC Class 1560, Airframe structural components) 20Ship and marine...

41 CFR 109-46.000-50 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Regulations System (Continued) DEPARTMENT OF ENERGY PROPERTY MANAGEMENT REGULATIONS UTILIZATION AND DISPOSAL... airframe structural components (except FSC Class 1560, Airframe structural components) 20Ship and marine...

41 CFR 109-46.000-50 - Applicability.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Regulations System (Continued) DEPARTMENT OF ENERGY PROPERTY MANAGEMENT REGULATIONS UTILIZATION AND DISPOSAL... airframe structural components (except FSC Class 1560, Airframe structural components) 20Ship and marine...

41 CFR 109-46.000-50 - Applicability.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Regulations System (Continued) DEPARTMENT OF ENERGY PROPERTY MANAGEMENT REGULATIONS UTILIZATION AND DISPOSAL... airframe structural components (except FSC Class 1560, Airframe structural components) 20Ship and marine...

Aeroacoustics of Propulsion Airframe Integration: Overview of NASA's Research

NASA Technical Reports Server (NTRS)

Thomas, Russell H.

2003-01-01

The integration of propulsion and airframe is fundamental to the design of an aircraft system. Many considerations influence the integration, such as structural, aerodynamic, and maintenance factors. In regard to the acoustics of an aircraft, the integration can have significant effects on the net radiated noise. Whether an engine is mounted above a wing or below can have a significant effect on noise that reaches communities below because of shielding or reflection of engine noise. This is an obvious example of the acoustic effects of propulsion airframe installation. Another example could be the effect of the pylon on the development of the exhaust plume and on the resulting jet noise. In addition, for effective system noise reduction the impact that installation has on noise reduction devices developed on isolated components must be understood. In the future, a focus on the aerodynamic and acoustic interaction effects of installation, propulsion airframe aeroacoustics, will become more important as noise reduction targets become more difficult to achieve. In addition to continued fundamental component reduction efforts, a system level approach that includes propulsion airframe aeroacoustics will be required in order to achieve the 20 dB of perceived noise reduction envisioned by the long-range NASA goals. This emphasis on the aeroacoustics of propulsion airframe integration is a new part of NASA s noise research. The following paper will review current efforts and highlight technical challenges and approaches.

Airframe noise

NASA Astrophysics Data System (ADS)

Crighton, David G.

1991-08-01

Current understanding of airframe noise was reviewed as represented by experiment at model and full scale, by theoretical modeling, and by empirical correlation models. The principal component sources are associated with the trailing edges of wing and tail, deflected trailing edge flaps, flap side edges, leading edge flaps or slats, undercarriage gear elements, gear wheel wells, fuselage and wing boundary layers, and panel vibration, together with many minor protrusions like radio antennas and air conditioning intakes which may contribute significantly to perceived noise. There are also possibilities for interactions between the various mechanisms. With current engine technology, the principal airframe noise mechanisms dominate only at low frequencies, typically less than 1 kHz and often much lower, but further reduction of turbomachinery noise in particular may make airframe noise the principal element of approach noise at frequencies in the sensitive range.

14 CFR 91.1413 - CAMP: Responsibility for airworthiness.

Code of Federal Regulations, 2013 CFR

2013-01-01

.... The Director of Maintenance must be a certificated mechanic with airframe and powerplant ratings who... or equivalent position. The Chief Inspector must be a certificated mechanic with airframe and...

14 CFR 91.1413 - CAMP: Responsibility for airworthiness.

Code of Federal Regulations, 2012 CFR

2012-01-01

.... The Director of Maintenance must be a certificated mechanic with airframe and powerplant ratings who... or equivalent position. The Chief Inspector must be a certificated mechanic with airframe and...

14 CFR 91.1413 - CAMP: Responsibility for airworthiness.

Code of Federal Regulations, 2014 CFR

2014-01-01

.... The Director of Maintenance must be a certificated mechanic with airframe and powerplant ratings who... or equivalent position. The Chief Inspector must be a certificated mechanic with airframe and...

14 CFR 91.1413 - CAMP: Responsibility for airworthiness.

Code of Federal Regulations, 2011 CFR

2011-01-01

.... The Director of Maintenance must be a certificated mechanic with airframe and powerplant ratings who... or equivalent position. The Chief Inspector must be a certificated mechanic with airframe and...

14 CFR 91.1413 - CAMP: Responsibility for airworthiness.

Code of Federal Regulations, 2010 CFR

2010-01-01

.... The Director of Maintenance must be a certificated mechanic with airframe and powerplant ratings who... or equivalent position. The Chief Inspector must be a certificated mechanic with airframe and...

Plan, formulate, discuss and correlate a NASTRAN finite element vibrations model of the Boeing Model 360 helicopter airframe

NASA Technical Reports Server (NTRS)

Gabel, R.; Lang, P. F.; Smith, L. A.; Reed, D. A.

1989-01-01

Boeing Helicopter, together with other United States helicopter manufacturers, participated in a finite element applications program to emplace in the United States a superior capability to utilize finite element analysis models in support of helicopter airframe design. The activities relating to planning and creating a finite element vibrations model of the Boeing Model 36-0 composite airframe are summarized, along with the subsequent analytical correlation with ground shake test data.

Environmental effects on composite airframes: A study conducted for the ARM UAV Program (Atmospheric Radiation Measurement Unmanned Aerospace Vehicle)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Noguchi, R.A.

1994-06-01

Composite materials are affected by environments differently than conventional airframe structural materials are. This study identifies the environmental conditions which the composite-airframe ARM UAV may encounter, and discusses the potential degradation processes composite materials may undergo when subjected to those environments. This information is intended to be useful in a follow-on program to develop equipment and procedures to prevent, detect, or otherwise mitigate significant degradation with the ultimate goal of preventing catastrophic aircraft failure.

14 CFR 147.17 - Instructional equipment requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Requirements § 147.17 Instructional equipment requirements. (a) An applicant for a mechanic school certificate... appropriate to the rating he seeks: (1) Various kinds of airframe structures, airframe systems and components...

14 CFR 147.17 - Instructional equipment requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Requirements § 147.17 Instructional equipment requirements. (a) An applicant for a mechanic school certificate... appropriate to the rating he seeks: (1) Various kinds of airframe structures, airframe systems and components...

14 CFR 147.17 - Instructional equipment requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Requirements § 147.17 Instructional equipment requirements. (a) An applicant for a mechanic school certificate... appropriate to the rating he seeks: (1) Various kinds of airframe structures, airframe systems and components...

14 CFR 147.17 - Instructional equipment requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Requirements § 147.17 Instructional equipment requirements. (a) An applicant for a mechanic school certificate... appropriate to the rating he seeks: (1) Various kinds of airframe structures, airframe systems and components...

Coupled rotor/airframe vibration analysis

NASA Technical Reports Server (NTRS)

Sopher, R.; Studwell, R. E.; Cassarino, S.; Kottapalli, S. B. R.

1982-01-01

A coupled rotor/airframe vibration analysis developed as a design tool for predicting helicopter vibrations and a research tool to quantify the effects of structural properties, aerodynamic interactions, and vibration reduction devices on vehicle vibration levels is described. The analysis consists of a base program utilizing an impedance matching technique to represent the coupled rotor/airframe dynamics of the system supported by inputs from several external programs supplying sophisticated rotor and airframe aerodynamic and structural dynamic representation. The theoretical background, computer program capabilities and limited correlation results are presented in this report. Correlation results using scale model wind tunnel results show that the analysis can adequately predict trends of vibration variations with airspeed and higher harmonic control effects. Predictions of absolute values of vibration levels were found to be very sensitive to modal characteristics and results were not representative of measured values.

KENNEDY SPACE CENTER, FLA. - On a tour of the Orbiter Processing Facility, Center Director Jim Kennedy (left) looks at an external tank door corrosion work being done on Endeavour. At right, Tom Roberts, Airframe Engineering System specialist with United Space Alliance, is describing the work. At right is Kathy Laufenberg, Orbiter Airframe Engineering ground area manager,also with USA. Endeavour is in its Orbiter Major Modification period, which began in December 2003.

NASA Image and Video Library

2004-02-25

KENNEDY SPACE CENTER, FLA. - On a tour of the Orbiter Processing Facility, Center Director Jim Kennedy (left) looks at an external tank door corrosion work being done on Endeavour. At right, Tom Roberts, Airframe Engineering System specialist with United Space Alliance, is describing the work. At right is Kathy Laufenberg, Orbiter Airframe Engineering ground area manager,also with USA. Endeavour is in its Orbiter Major Modification period, which began in December 2003.

Experiences at Langley Research Center in the application of optimization techniques to helicopter airframes for vibration reduction

NASA Technical Reports Server (NTRS)

Murthy, T. Sreekanta; Kvaternik, Raymond G.

1991-01-01

A NASA/industry rotorcraft structural dynamics program known as Design Analysis Methods for VIBrationS (DAMVIBS) was initiated at Langley Research Center in 1984 with the objective of establishing the technology base needed by the industry for developing an advanced finite-element-based vibrations design analysis capability for airframe structures. As a part of the in-house activities contributing to that program, a study was undertaken to investigate the use of formal, nonlinear programming-based, numerical optimization techniques for airframe vibrations design work. Considerable progress has been made in connection with that study since its inception in 1985. This paper presents a unified summary of the experiences and results of that study. The formulation and solution of airframe optimization problems are discussed. Particular attention is given to describing the implementation of a new computational procedure based on MSC/NASTRAN and CONstrained function MINimization (CONMIN) in a computer program system called DYNOPT for the optimization of airframes subject to strength, frequency, dynamic response, and fatigue constraints. The results from the application of the DYNOPT program to the Bell AH-1G helicopter are presented and discussed.

Simulations & Measurements of Airframe Noise: A BANC Workshops Perspective

NASA Technical Reports Server (NTRS)

Choudhari, Meelan; Lockard, David

2016-01-01

Airframe noise corresponds to the acoustic radiation due to turbulent flow in the vicinity of airframe components such as high-lift devices and landing gears. Since 2010, the American Institute of Aeronautics and Astronautics has organized an ongoing series of workshops devoted to Benchmark Problems for Airframe Noise Computations (BANC). The BANC workshops are aimed at enabling a systematic progress in the understanding and high-fidelity predictions of airframe noise via collaborative investigations that integrate computational fluid dynamics, computational aeroacoustics, and in depth measurements targeting a selected set of canonical yet realistic configurations that advance the current state-of-the-art in multiple respects. Unique features of the BANC Workshops include: intrinsically multi-disciplinary focus involving both fluid dynamics and aeroacoustics, holistic rather than predictive emphasis, concurrent, long term evolution of experiments and simulations with a powerful interplay between the two, and strongly integrative nature by virtue of multi-team, multi-facility, multiple-entry measurements. This paper illustrates these features in the context of the BANC problem categories and outlines some of the challenges involved and how they were addressed. A brief summary of the BANC effort, including its technical objectives, strategy, and selective outcomes thus far is also included.

Synergistic Airframe-Propulsion Interactions and Integrations: A White Paper Prepared by the 1996-1997 Langley Aeronautics Technical Committee

NASA Technical Reports Server (NTRS)

Yaros, Steven F.; Sexstone, Matthew G.; Huebner, Lawrence D.; Lamar, John E.; McKinley, Robert E., Jr.; Torres, Abel O.; Burley, Casey L.; Scott, Robert C.; Small, William J.

1998-01-01

This white paper addresses the subject of Synergistic Airframe-Propulsion interactions and integrations (SnAPII). The benefits of SnAPII have not been as extensively explored. This is due primarily to the separateness of design process for airframes and propulsion systems, with only unfavorable interactions addressed. The question 'How to design these two systems in such a way that the airframe needs the propulsion and the propulsion needs the airframe?' is the fundamental issue addressed in this paper. Successful solutions to this issue depend on appropriate technology ideas. This paper first details some ten technologies that have yet to make it to commercial products (with limited exceptions) and that could be utilized in a synergistic manner. Then these technologies, either alone or in combination, are applied to both a conventional twin-engine transonic transport and to an unconventional transport, the Blended Wing Body. Lastly, combinations of these technologies are applied to configuration concepts to assess the possibilities of success relative to five of the ten NASA aeronautics goals. These assessments are subjective, but they point the way in which the applied technologies could work together for some break-through benefits.

Critical Life Prediction Research on Boron-Enhanced Ti-6A1-4V

DTIC Science & Technology

2007-05-01

2.4 High Modulus Ti-6Al-2Fe-0.1Si-0.6B “T” Extrusions for HSCT program. Ref. Government Contract No. NASI -20220: High Speed Research-Airframe...0.1Si-0.6B “T” Extrusions for HSCT program. Ref. Government Contract No. NASI -20220: High Speed Research-Airframe Technology report. with the focus...baseline Ti-6Al-4V (Government Contract No. NASI -20220, High Speed Research-Airframe Technology Report, 1997: 3-5, 14, 26). 1 in 3 in 16 In

Study to investigate design, fabrication and test of low cost concepts for large hybrid composite helicopter fuselage, phase 2

NASA Technical Reports Server (NTRS)

Adams, K. M.; Lucas, J. J.

1977-01-01

The development of a frame/stringer/skin fabrication technique for composite airframe construction was studied as a low cost approach to the manufacturer of larger helicopter airframe components. A center cabin aluminum airframe section of the Sikorsky CH-53D, was selected for evaluation as a composite structure. The design, as developed, is composed of a woven KEVLAR R-49/epoxy skin and graphite/epoxy frames and stringers. The single cure concept is made possible by the utilization of pre-molded foam cores, over which the graphite/epoxy pre-impregnated frame and stringer reinforcements are positioned. Bolted composite channel sections were selected as the optimum joint construction. The applicability of the single cure concept to larger realistic curved airframe sections, and the durability of the composite structure in a realistic spectrum fatigue environment, was described.

Data and results from a study of internal convective cooling systems for hypersonic aircraft

NASA Technical Reports Server (NTRS)

Anthony, F. M.; Dukes, W. H.; Helenbrook, R. G.

1974-01-01

An extensive survey of current and future airframe construction materials and coolants was conducted, so that the most promising candidates could be examined for cooled-panel, cooling-system and airframe concepts. Consideration was given to over 100 structural materials, 50 coolants, 6 classes of structural panel concepts, 4 classes of thermal panel concepts with numerous variations, and 3 overall cooled airframe design approaches, including unshielded, shielded, and dual temperature types. The concept identification and parametric comparison phase examined all major elements of the convectively cooled airframe, including the differing requirements at various locations on the aircraft. The parametric results were used for the investigation to two separate vehicles, a hypersonic transport with a length of 96 meters (314 feet) and a weight of 24,000 kg (528,600 lb) and a hypersonic research airplane, with a length of 25m (80 ft) and a weight of 20,300 kg (447,000 lb).

Lattice Boltzmann and Navier-Stokes Cartesian CFD Approaches for Airframe Noise Predictions

NASA Technical Reports Server (NTRS)

Barad, Michael F.; Kocheemoolayil, Joseph G.; Kiris, Cetin C.

2017-01-01

Lattice Boltzmann (LB) and compressible Navier-Stokes (NS) equations based computational fluid dynamics (CFD) approaches are compared for simulating airframe noise. Both LB and NS CFD approaches are implemented within the Launch Ascent and Vehicle Aerodynamics (LAVA) framework. Both schemes utilize the same underlying Cartesian structured mesh paradigm with provision for local adaptive grid refinement and sub-cycling in time. We choose a prototypical massively separated, wake-dominated flow ideally suited for Cartesian-grid based approaches in this study - The partially-dressed, cavity-closed nose landing gear (PDCC-NLG) noise problem from AIAA's Benchmark problems for Airframe Noise Computations (BANC) series of workshops. The relative accuracy and computational efficiency of the two approaches are systematically compared. Detailed comments are made on the potential held by LB to significantly reduce time-to-solution for a desired level of accuracy within the context of modeling airframes noise from first principles.

Preliminary measurement of the airframe noise from an F-106B delta wing aircraft at low flyover speeds. [establishment of lower limit for noise level of supersonic transport aircraft

NASA Technical Reports Server (NTRS)

Burley, R. R.

1974-01-01

To establish a realistic lower limit for the noise level of advanced supersonic transport aircraft will require knowledge concerning the amount of noise generated by the airframe itself as it moves through the air. The airframe noise level of an F-106B aircraft was determined and was compared to that predicted from an existing empirical relationship. The data were obtained from flyover and static tests conducted to determine the background noise level of the F-106B aircraft. Preliminary results indicate that the spectrum associated with airframe noise was broadband and peaked at a frequency of about 570 hertz. An existing empirical method successfully predicted the frequency where the spectrum peaked. However, the predicted OASPL value of 105 db was considerably greater than the measures value of 83 db.

KENNEDY SPACE CENTER, FLA. - On a tour of the Orbiter Processing Facility, Center Director Jim Kennedy and Deputy Director Woodrow Whitlow Jr. (center, left and right) talk with Kathy Laufenberg, Orbiter Airframe Engineering ground rea manager, and Tom Roberts, Airframe Engineering System specialist, both with United Space Alliance. At far right is Bruce Buckingham, assistant to Dr. Whitlow. They are standing in front of the aft base heatshield of Endeavour, which is in its Orbiter Major Modification period that began in December 2003.

NASA Image and Video Library

2004-02-25

KENNEDY SPACE CENTER, FLA. - On a tour of the Orbiter Processing Facility, Center Director Jim Kennedy and Deputy Director Woodrow Whitlow Jr. (center, left and right) talk with Kathy Laufenberg, Orbiter Airframe Engineering ground rea manager, and Tom Roberts, Airframe Engineering System specialist, both with United Space Alliance. At far right is Bruce Buckingham, assistant to Dr. Whitlow. They are standing in front of the aft base heatshield of Endeavour, which is in its Orbiter Major Modification period that began in December 2003.

KENNEDY SPACE CENTER, FLA. - On a tour of the Orbiter Processing Facility, Center Director Jim Kennedy and Deputy Director Woodrow Whitlow Jr. (center, left and right) talk with Kathy Laufenberg, Orbiter Airframe Engineering ground area manager, and Tom Roberts, Airframe Enginering System specialist, both with United Space Alliance. At far right is Bruce Buckingham, assistant to Dr. Whitlow. They are standing in front of the aft base heatshield of Endeavour, which is in its Orbiter Major Modification period that began in December 2003.

NASA Image and Video Library

2004-02-25

KENNEDY SPACE CENTER, FLA. - On a tour of the Orbiter Processing Facility, Center Director Jim Kennedy and Deputy Director Woodrow Whitlow Jr. (center, left and right) talk with Kathy Laufenberg, Orbiter Airframe Engineering ground area manager, and Tom Roberts, Airframe Enginering System specialist, both with United Space Alliance. At far right is Bruce Buckingham, assistant to Dr. Whitlow. They are standing in front of the aft base heatshield of Endeavour, which is in its Orbiter Major Modification period that began in December 2003.

KENNEDY SPACE CENTER, FLA. - On a tour of the Orbiter Processing Facility, Center Director Jim Kennedy (left) listens to Kathy Laufenberg, Orbiter Airframe Engineering ground area manager, with United Space Alliance, about corrosion work being done on the external tank door of orbiter Endeavour. On either side of Laufenberg are Tom Roberts, Airframe Engineering System specialist, also with USA, and Joy Huff, with KSC Space Shuttle Processing. Endeavour is in its Orbiter Major Modification period, which began in December 2003.

NASA Image and Video Library

2004-02-25

KENNEDY SPACE CENTER, FLA. - On a tour of the Orbiter Processing Facility, Center Director Jim Kennedy (left) listens to Kathy Laufenberg, Orbiter Airframe Engineering ground area manager, with United Space Alliance, about corrosion work being done on the external tank door of orbiter Endeavour. On either side of Laufenberg are Tom Roberts, Airframe Engineering System specialist, also with USA, and Joy Huff, with KSC Space Shuttle Processing. Endeavour is in its Orbiter Major Modification period, which began in December 2003.

Numerical methods for engine-airframe integration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murthy, S.N.B.; Paynter, G.C.

1986-01-01

Various papers on numerical methods for engine-airframe integration are presented. The individual topics considered include: scientific computing environment for the 1980s, overview of prediction of complex turbulent flows, numerical solutions of the compressible Navier-Stokes equations, elements of computational engine/airframe integrations, computational requirements for efficient engine installation, application of CAE and CFD techniques to complete tactical missile design, CFD applications to engine/airframe integration, and application of a second-generation low-order panel methods to powerplant installation studies. Also addressed are: three-dimensional flow analysis of turboprop inlet and nacelle configurations, application of computational methods to the design of large turbofan engine nacelles, comparison ofmore » full potential and Euler solution algorithms for aeropropulsive flow field computations, subsonic/transonic, supersonic nozzle flows and nozzle integration, subsonic/transonic prediction capabilities for nozzle/afterbody configurations, three-dimensional viscous design methodology of supersonic inlet systems for advanced technology aircraft, and a user's technology assessment.« less

Preliminary Analysis of Acoustic Measurements from the NASA-Gulfstream Airframe Noise Flight Test

NASA Technical Reports Server (NTRS)

Khorrami, Mehdi R.; Lockhard, David D.; Humphreys, Willliam M.; Choudhari, Meelan M.; Van De Ven, Thomas

2008-01-01

The NASA-Gulfstream joint Airframe Noise Flight Test program was conducted at the NASA Wallops Flight Facility during October, 2006. The primary objective of the AFN flight test was to acquire baseline airframe noise data on a regional jet class of transport in order to determine noise source strengths and distributions for model validation. To accomplish this task, two measuring systems were used: a ground-based microphone array and individual microphones. Acoustic data for a Gulfstream G550 aircraft were acquired over the course of ten days. Over twenty-four test conditions were flown. The test matrix was designed to provide an acoustic characterization of both the full aircraft and individual airframe components and included cruise to landing configurations. Noise sources were isolated by selectively deploying individual components (flaps, main landing gear, nose gear, spoilers, etc.) and altering the airspeed, glide path, and engine settings. The AFN flight test program confirmed that the airframe is a major contributor to the noise from regional jets during landing operations. Sound pressure levels from the individual microphones on the ground revealed the flap system to be the dominant airframe noise source for the G550 aircraft. The corresponding array beamform maps showed that most of the radiated sound from the flaps originates from the side edges. Using velocity to the sixth power and Strouhal scaling of the sound pressure spectra obtained at different speeds failed to collapse the data into a single spectrum. The best data collapse was obtained when the frequencies were left unscaled.

Historical review of tactical missile airframe developments

NASA Technical Reports Server (NTRS)

Spearman, M. L.

1992-01-01

A comprehensive development history of missile airframe aerodynamics is presented, encompassing ground-, ground vehicle-, ship-, and air-launched categories of all ranges short of strategic. Emphasis is placed on the swift acceleration of missile configuration aerodynamics by German researchers in the course of the Second World War and by U.S. research establishments thereafter, often on the foundations laid by German workers. Examples are given of foundational airframe design criteria established by systematic researches undertaken in the 1950s, regarding L/D ratios, normal force and pitching moment characteristics, minimum drag forebodies and afterbodies, and canard and delta winged configuration aerodynamics.

Propeller propulsion system integration: State of technology survey

NASA Technical Reports Server (NTRS)

Miley, S. J.; Vonlavante, E.

1985-01-01

A literature survey was performed to identify and review technical material applicable to the problem area of propeller propulsion system integration. The survey covered only aerodynamic interference aspects of the problem, and was restricted primarily to propeller effects on the airframe. The subject of airframe aerodynamic interference on the propeller was limited to the problem of vibration due to nonuniform inflow. The problem of airframe effects on propeller performance was not included. A total of 1121 references are given. The references are grouped into the subject areas of Aircraft Stability, Propulsive Efficiency, Aerodynamic Interference, Aerodynamic Interference-Propeller Vibration, and Miscellaneous.

Light aircraft crash safety program

NASA Technical Reports Server (NTRS)

Thomson, R. G.; Hayduk, R. J.

1974-01-01

NASA is embarked upon research and development tasks aimed at providing the general aviation industry with a reliable crashworthy airframe design technology. The goals of the NASA program are: reliable analytical techniques for predicting the nonlinear behavior of structures; significant design improvements of airframes; and simulated full-scale crash test data. The analytical tools will include both simplified procedures for estimating energy absorption characteristics and more complex computer programs for analysis of general airframe structures under crash loading conditions. The analytical techniques being developed both in-house and under contract are described, and a comparison of some analytical predictions with experimental results is shown.

Scramjet integration on hypersonic research airplane concepts

NASA Technical Reports Server (NTRS)

Weidner, J. P.; Small, W. J.; Penland, J. A.

1976-01-01

Several rocket-boosted research airplane concepts were evaluated with a research scramjet engine to determine their potential to provide research on critical aspects of airframe-integrated hypersonic systems. Extensive calculations to determine the force and moment contributions of the scramjet inlet, combustor, nozzle, and airframe were conducted to evaluate the overall performance of the combined engine/airframe system at hypersonic speeds. Results of both wind-tunnel tests and analysis indicate that it is possible to develop a research airplane configuration that will cruise at hypersonic speed on scramjet power alone, and will also have acceptable low-speed aerodynamic characteristics for landing.

Ground shake test of the UH-60A helicopter airframe and comparison with NASTRAN finite element model predictions

NASA Technical Reports Server (NTRS)

Howland, G. R.; Durno, J. A.; Twomey, W. J.

1990-01-01

Sikorsky Aircraft, together with the other major helicopter airframe manufacturers, is engaged in a study to improve the use of finite element analysis to predict the dynamic behavior of helicopter airframes, under a rotorcraft structural dynamics program called DAMVIBS (Design Analysis Methods for VIBrationS), sponsored by the NASA-Langley. The test plan and test results are presented for a shake test of the UH-60A BLACK HAWK helicopter. A comparison is also presented of test results with results obtained from analysis using a NASTRAN finite element model.

Hyper-X Engine Testing in the NASA Langley 8-Foot High Temperature Tunnel

NASA Technical Reports Server (NTRS)

Huebner, Lawrence D.; Rock, Kenneth E.; Witte, David W.; Ruf, Edward G.; Andrews, Earl H., Jr.

2000-01-01

Airframe-integrated scramjet engine tests have 8 completed at Mach 7 in the NASA Langley 8-Foot High Temperature Tunnel under the Hyper-X program. These tests provided critical engine data as well as design and database verification for the Mach 7 flight tests of the Hyper-X research vehicle (X-43), which will provide the first-ever airframe- integrated scramjet flight data. The first model tested was the Hyper-X Engine Model (HXEM), and the second was the Hyper-X Flight Engine (HXFE). The HXEM, a partial-width, full-height engine that is mounted on an airframe structure to simulate the forebody features of the X-43, was tested to provide data linking flowpath development databases to the complete airframe-integrated three-dimensional flight configuration and to isolate effects of ground testing conditions and techniques. The HXFE, an exact geometric representation of the X-43 scramjet engine mounted on an airframe structure that duplicates the entire three-dimensional propulsion flowpath from the vehicle leading edge to the vehicle base, was tested to verify the complete design as it will be flight tested. This paper presents an overview of these two tests, their importance to the Hyper-X program, and the significance of their contribution to scramjet database development.

A comparative study of multivariable robustness analysis methods as applied to integrated flight and propulsion control

NASA Technical Reports Server (NTRS)

Schierman, John D.; Lovell, T. A.; Schmidt, David K.

1993-01-01

Three multivariable robustness analysis methods are compared and contrasted. The focus of the analysis is on system stability and performance robustness to uncertainty in the coupling dynamics between two interacting subsystems. Of particular interest is interacting airframe and engine subsystems, and an example airframe/engine vehicle configuration is utilized in the demonstration of these approaches. The singular value (SV) and structured singular value (SSV) analysis methods are compared to a method especially well suited for analysis of robustness to uncertainties in subsystem interactions. This approach is referred to here as the interacting subsystem (IS) analysis method. This method has been used previously to analyze airframe/engine systems, emphasizing the study of stability robustness. However, performance robustness is also investigated here, and a new measure of allowable uncertainty for acceptable performance robustness is introduced. The IS methodology does not require plant uncertainty models to measure the robustness of the system, and is shown to yield valuable information regarding the effects of subsystem interactions. In contrast, the SV and SSV methods allow for the evaluation of the robustness of the system to particular models of uncertainty, and do not directly indicate how the airframe (engine) subsystem interacts with the engine (airframe) subsystem.

76 FR 76066 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-06

... Sutherland, Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office, 1601...: james.sutherland@faa.gov . SUPPLEMENTARY INFORMATION: Comments Invited We invite you to send any written... about this AD, contact James Sutherland, Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle...

76 FR 77937 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-15

... Sutherland, Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office (ACO...: James.Sutherland@faa.gov . SUPPLEMENTARY INFORMATION: Comments Invited We invite you to send any written... Information (1) For more information about this AD, contact James Sutherland, Aerospace Engineer, Airframe...

77 FR 32889 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-04

...., Washington, DC 20590. FOR FURTHER INFORMATION CONTACT: James Sutherland, Aerospace Engineer, Airframe Branch... 98057-3356; phone: 425- 917-6533; fax: 425-917-6590; email: James.Sutherland@faa.gov . SUPPLEMENTARY... more information about this AD, contact James Sutherland, Aerospace Engineer, Airframe Branch, ANM-120S...

77 FR 42962 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-23

... INFORMATION CONTACT: James Sutherland, Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle Aircraft...-6590; email: James.Sutherland@faa.gov . SUPPLEMENTARY INFORMATION: Discussion We issued a notice of... this AD, contact James Sutherland, Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle Aircraft...

Preliminary Design of Winged Experimental Rocket by University Consortium

NASA Astrophysics Data System (ADS)

Wakita, Masashi; Yonemoto, Koichi; Akiyama, Tomoki; Aso, Shigeru; Kohsetsu, Yuji; Nagata, Harunori

The project of Winged Experimental Rocket described here is a proposal by the alliance of universities (University Consortium) expanding and integrating the research activities of reusable space transportation system performed by individual universities, and is the proposal that aims at flight proof of the results of advanced research conducted by the universities and JAXA using the university-centered experimental launch systems. This paper verifies the validity of the winged experimental rocket by surveying the technical issues that should be demonstrated and by estimating the airframe scale, weight and finally the total cost. The development schedule of this project was set to five years, where two airframes of different scales will be developed to minimize the risks. A 1.5-meter-long airframe will be first manufactured and conduct flight tests in the third year to verify the design issues. Then, a 2.5-meter-long airframe will be finally developed and conduct a complete flight demonstration of various research issues in the fifth year.

An Unpowered Exoskeleton to Reduce Astronaut Hand Fatigue during Microgravity EVA

NASA Astrophysics Data System (ADS)

Carey, Alan John

Improving manufacturing techniques to minimize costs have always been the ultimate goal for engineers since the dawn of technology. Working toward making the end product as affordable as possible without compromising on its quality is not just a skill set to develop but also, art. This thesis deals with changing the approach to the manufacturing of the patented XQ-139 UAV by using alternative materials to reduce production costs and time. Retaining the overall structure and utility of the UAV while eliminating the high costs to produce is the primary goal. It also includes tests performed on the new UAV airframe to prove this hypothesis and compare it to the results of the original airframe. The objective is to prove that the new airframe can cope with the structural and performance demands of the original XQ-139A, while reducing the total costs to manufacture it. This thesis only deals with the processing and manufacturing of the new XQ-139A airframe. No flight tests are involved.

The Prediction of Noise Due to Jet Turbulence Convecting Past Flight Vehicle Trailing Edges

NASA Technical Reports Server (NTRS)

Miller, Steven A. E.

2014-01-01

High intensity acoustic radiation occurs when turbulence convects past airframe trailing edges. A mathematical model is developed to predict this acoustic radiation. The model is dependent on the local flow and turbulent statistics above the trailing edge of the flight vehicle airframe. These quantities are dependent on the jet and flight vehicle Mach numbers and jet temperature. A term in the model approximates the turbulent statistics of single-stream heated jet flows and is developed based upon measurement. The developed model is valid for a wide range of jet Mach numbers, jet temperature ratios, and flight vehicle Mach numbers. The model predicts traditional trailing edge noise if the jet is not interacting with the airframe. Predictions of mean-flow quantities and the cross-spectrum of static pressure near the airframe trailing edge are compared with measurement. Finally, predictions of acoustic intensity are compared with measurement and the model is shown to accurately capture the phenomenon.

Microstructural and Mechanical Characterization of Shear Formed Aluminum Alloys for Airframe and Space Applications

NASA Technical Reports Server (NTRS)

Troeger, L. P.; Domack, M. S.; Wagner, J. A.

1998-01-01

Advanced manufacturing processes such as near-net-shape forming can reduce production costs and increase the reliability of launch vehicle and airframe structural components through the reduction of material scrap and part count and the minimization of joints. The current research is an investigation of the processing-microstructure-property relationship for shear formed cylinders of the Al-Cu-Li-Mg-Ag alloy 2195 for space applications and the Al-Cu-Mg-Ag alloy C415 for airframe applications. Cylinders which have undergone various amounts of shear-forming strain have been studied to assess the microstructure and mechanical properties developed during and after shear forming.

Longitudinal acceleration tests of overhead luggage bins and auxiliary fuel tank in a transport airplane airframe section

DOT National Transportation Integrated Search

1999-06-01

This report contains the description and test results of overhead stowage bin calibrations and longitudinal impact testing of a 10-foot transport airframe section conducted at the Transportation Research Center Inc. (TRC). The purpose of the tests wa...

14 CFR 65.73 - Ratings.

Code of Federal Regulations, 2011 CFR

2011-01-01

... CERTIFICATION: AIRMEN OTHER THAN FLIGHT CREWMEMBERS Mechanics § 65.73 Ratings. (a) The following ratings are issued under this subpart: (1) Airframe. (2) Powerplant. (b) A mechanic certificate with an aircraft or... mechanic certificate with an airframe or powerplant rating, or both, as the case may be, and may be...

14 CFR 65.73 - Ratings.

Code of Federal Regulations, 2010 CFR

2010-01-01

... CERTIFICATION: AIRMEN OTHER THAN FLIGHT CREWMEMBERS Mechanics § 65.73 Ratings. (a) The following ratings are issued under this subpart: (1) Airframe. (2) Powerplant. (b) A mechanic certificate with an aircraft or... mechanic certificate with an airframe or powerplant rating, or both, as the case may be, and may be...

14 CFR 65.73 - Ratings.

Code of Federal Regulations, 2012 CFR

2012-01-01

... CERTIFICATION: AIRMEN OTHER THAN FLIGHT CREWMEMBERS Mechanics § 65.73 Ratings. (a) The following ratings are issued under this subpart: (1) Airframe. (2) Powerplant. (b) A mechanic certificate with an aircraft or... mechanic certificate with an airframe or powerplant rating, or both, as the case may be, and may be...

14 CFR 65.73 - Ratings.

Code of Federal Regulations, 2013 CFR

2013-01-01

... CERTIFICATION: AIRMEN OTHER THAN FLIGHT CREWMEMBERS Mechanics § 65.73 Ratings. (a) The following ratings are issued under this subpart: (1) Airframe. (2) Powerplant. (b) A mechanic certificate with an aircraft or... mechanic certificate with an airframe or powerplant rating, or both, as the case may be, and may be...

14 CFR 65.73 - Ratings.

Code of Federal Regulations, 2014 CFR

2014-01-01

... CERTIFICATION: AIRMEN OTHER THAN FLIGHT CREWMEMBERS Mechanics § 65.73 Ratings. (a) The following ratings are issued under this subpart: (1) Airframe. (2) Powerplant. (b) A mechanic certificate with an aircraft or... mechanic certificate with an airframe or powerplant rating, or both, as the case may be, and may be...

14 CFR 145.61 - Limited ratings.

Code of Federal Regulations, 2013 CFR

2013-01-01

... of airframe, powerplant, propeller, radio, instrument, or accessory, or part thereof, or performs... station ratings. Such a rating may be limited to a specific model aircraft, engine, or constituent part...— (1) Airframes of a particular make and model; (2) Engines of a particular make and model; (3...

Airframe technology for aircraft energy efficiency. [economic factors

NASA Technical Reports Server (NTRS)

James, R. L., Jr.; Maddalon, D. V.

1984-01-01

The economic factors that resulted in the implementation of the aircraft energy efficiency program (ACEE) are reviewed and airframe technology elements including content, progress, applications, and future direction are discussed. The program includes the development of laminar flow systems, advanced aerodynamics, active controls, and composite structures.

Overview of the Transport Rotorcraft Airframe Crash Testbed (TRACT) Full Scale Crash Tests

NASA Technical Reports Server (NTRS)

Annett, Martin; Littell, Justin

2015-01-01

The Transport Rotorcraft Airframe Crash Testbed (TRACT) full-scale tests were performed at NASA Langley Research Center's Landing and Impact Research Facility in 2013 and 2014. Two CH-46E airframes were impacted at 33-ft/s forward and 25-ft/s vertical combined velocities onto soft soil, which represents a severe, but potentially survivable impact scenario. TRACT 1 provided a baseline set of responses, while TRACT 2 included retrofits with composite subfloors and other crash system improvements based on TRACT 1. For TRACT 2, a total of 18 unique experiments were conducted to evaluate Anthropomorphic Test Devices (ATD) responses, seat and restraint performance, cargo restraint effectiveness, patient litter behavior, and activation of emergency locator transmitters and crash sensors. Combinations of Hybrid II, Hybrid III, and ES-2 ATDs were placed in forward and side facing seats and occupant results were compared against injury criteria. The structural response of the airframe was assessed based on accelerometers located throughout the airframe and using three-dimensional photogrammetric techniques. Analysis of the photogrammetric data indicated regions of maximum deflection and permanent deformation. The response of TRACT 2 was noticeably different in the horizontal direction due to changes in the cabin configuration and soil surface, with higher acceleration and damage occurring in the cabin. Loads from ATDs in energy absorbing seats and restraints were within injury limits. Severe injury was likely for ATDs in forward facing passenger seats.

75 FR 47197 - Airworthiness Directives; Schweizer Aircraft Corporation (Schweizer) Model 269D Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-05

..., Aviation Safety Engineer, FAA, New York Aircraft Certification Office, Airframe and Propulsion Branch, 1600..., Aerospace Engineer, Aviation Safety Engineer, FAA, New York Aircraft Certification Office, Airframe and Propulsion Branch, 1600 Stewart Ave., suite 410, Westbury, New York 11590, telephone (516) 228-7304, fax (516...

Design of a convective cooling system for a Mach 6 hypersonic transport airframe

NASA Technical Reports Server (NTRS)

Helenbrook, R. G.; Anthony, F. M.

1971-01-01

Results of analytical and design studies are presented for a water-glycol convective cooling system for the airframe structure of a hypersonic transport. System configurations and weights are compared. The influences of system pressure drop and flow control schedules on system weight are defined.

14 CFR Appendix B to Part 43 - Recording of Major Repairs and Major Alterations

Code of Federal Regulations, 2014 CFR

2014-01-01

..., within 48 hours after the aircraft, airframe, aircraft engine, propeller, or appliance is approved for... approval for return to service of the aircraft, airframe, aircraft engine, propeller, or appliance; (3... engine, propeller or appliance. (ii) If an aircraft, the make, model, serial number, nationality and...

14 CFR Appendix B to Part 43 - Recording of Major Repairs and Major Alterations

Code of Federal Regulations, 2011 CFR

2011-01-01

..., within 48 hours after the aircraft, airframe, aircraft engine, propeller, or appliance is approved for... approval for return to service of the aircraft, airframe, aircraft engine, propeller, or appliance; (3... engine, propeller or appliance. (ii) If an aircraft, the make, model, serial number, nationality and...

14 CFR 121.380 - Maintenance recording requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... section, the total time in service of each engine and propeller. (iii) The current status of life-limited parts of each airframe, engine, propeller, and appliance. (iv) The time since last overhaul of all items... required. (vii) A list of current major alterations to each airframe, engine, propeller, and appliance. (b...

14 CFR 121.380 - Maintenance recording requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... section, the total time in service of each engine and propeller. (iii) The current status of life-limited parts of each airframe, engine, propeller, and appliance. (iv) The time since last overhaul of all items... required. (vii) A list of current major alterations to each airframe, engine, propeller, and appliance. (b...

14 CFR 121.380 - Maintenance recording requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... section, the total time in service of each engine and propeller. (iii) The current status of life-limited parts of each airframe, engine, propeller, and appliance. (iv) The time since last overhaul of all items... required. (vii) A list of current major alterations to each airframe, engine, propeller, and appliance. (b...

14 CFR 121.380 - Maintenance recording requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... section, the total time in service of each engine and propeller. (iii) The current status of life-limited parts of each airframe, engine, propeller, and appliance. (iv) The time since last overhaul of all items... required. (vii) A list of current major alterations to each airframe, engine, propeller, and appliance. (b...

14 CFR 121.380 - Maintenance recording requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... section, the total time in service of each engine and propeller. (iii) The current status of life-limited parts of each airframe, engine, propeller, and appliance. (iv) The time since last overhaul of all items... required. (vii) A list of current major alterations to each airframe, engine, propeller, and appliance. (b...

14 CFR Appendix B to Part 43 - Recording of Major Repairs and Major Alterations

Code of Federal Regulations, 2010 CFR

2010-01-01

..., within 48 hours after the aircraft, airframe, aircraft engine, propeller, or appliance is approved for... approval for return to service of the aircraft, airframe, aircraft engine, propeller, or appliance; (3... engine, propeller or appliance. (ii) If an aircraft, the make, model, serial number, nationality and...

14 CFR Appendix B to Part 43 - Recording of Major Repairs and Major Alterations

Code of Federal Regulations, 2012 CFR

2012-01-01

..., within 48 hours after the aircraft, airframe, aircraft engine, propeller, or appliance is approved for... approval for return to service of the aircraft, airframe, aircraft engine, propeller, or appliance; (3... engine, propeller or appliance. (ii) If an aircraft, the make, model, serial number, nationality and...

Advanced general aviation comparative engine/airframe integration study

NASA Technical Reports Server (NTRS)

Huggins, G. L.; Ellis, D. R.

1981-01-01

The NASA Advanced Aviation Comparative Engine/Airframe Integration Study was initiated to help determine which of four promising concepts for new general aviation engines for the 1990's should be considered for further research funding. The engine concepts included rotary, diesel, spark ignition, and turboprop powerplants; a conventional state-of-the-art piston engine was used as a baseline for the comparison. Computer simulations of the performance of single and twin engine pressurized aircraft designs were used to determine how the various characteristics of each engine interacted in the design process. Comparisons were made of how each engine performed relative to the others when integrated into an airframe and required to fly a transportation mission.

Overview of mechanics of materials branch activities in the computational structures area

NASA Technical Reports Server (NTRS)

Poe, C. C., Jr.

1992-01-01

Base programs and system programs are discussed. The base programs include fundamental research of composites and metals for airframes leading to characterization of advanced materials, models of behavior, and methods for predicting damage tolerance. Results from the base programs support the systems programs, which change as NASA's missions change. The National Aerospace Plane (NASP), Advanced Composites Technology (ACT), Airframe Structural Integrity Program (Aging Aircraft), and High Speed Research (HSR) programs are currently being supported. Airframe durability is one of the key issues in each of these system programs. The base program has four major thrusts, which will be reviewed subsequently. Additionally, several technical highlights will be reviewed for each thrust.

Easy method of matching fighter engine to airframe for use in aircraft engine design courses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mattingly, J.D.

1989-01-01

The proper match of the engine(s) to the airframe affects both aircraft size and life cycle cost. A fast and straightforward method is developed and used for the matching of fighter engine(s) to airframes during conceptual design. A thrust-lapse equation is developed for the dual-spool, mixed-flow, afterburning turbofan type of engine based on the installation losses of 'Aircraft Engine Design' and the performance predictions of the cycle analysis programs ONX and OFFX. Using system performance requirements, the effects of aircraft thrust-to-weight, wing loading, and engine cycle on takeoff weight are analyzed and example design course results presented. 5 refs.

Airframe Repair Specialist, 2-3. Military Curriculum Materials for Vocational and Technical Education.

ERIC Educational Resources Information Center

Ohio State Univ., Columbus. National Center for Research in Vocational Education.

These military-developed curriculum materials consist of five volumes of individualized, self-paced training manuals for use by those studying to be airframe repair technicians. Covered in the individual volumes are the following topics: fundamentals of organization and management (ground safety, aircraft ground safety, and aerospace and power…

76 FR 71470 - Airworthiness Directives; Bombardier, Inc. Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-18

... brackets that attach the power control unit (PCU) to the airframe could result in a loss of the rudder actuating system. The loss of both rudder PCU actuators could result in free play of the rudder control... failure of the mounting brackets that attach the power control unit (PCU) to the airframe could result in...

Design of an integrated airframe/propulsion control system architecture

NASA Technical Reports Server (NTRS)

Cohen, Gerald C.; Lee, C. William; Strickland, Michael J.; Torkelson, Thomas C.

1990-01-01

The design of an integrated airframe/propulsion control system architecture is described. The design is based on a prevalidation methodology that uses both reliability and performance. A detailed account is given for the testing associated with a subset of the architecture and concludes with general observations of applying the methodology to the architecture.

The NASA/industry design analysis methods for vibrations (DAMVIBS) program - Accomplishments and contributions

NASA Technical Reports Server (NTRS)

Kvaternik, Raymond G.

1991-01-01

A NASA Langley-sponsored rotorcraft structural dynamics program, known as Design Analysis Methods for VIBrationS (DAMVIBS), has been under development since 1984. The objective of this program was to establish the technology base needed by the industry to develop an advanced finite-element-based dynamics design analysis capability for vibrations. Under the program, teams from the four major helicopter manufacturers have formed finite-element models, conducted ground vibration tests, made test/analysis comparisons of both metal and composite airframes, performed 'difficult components' studies on airframes to identify components which need more complete finite-element representation for improved correlation, and evaluated industry codes for computing coupled rotor-airframe vibrations. Studies aimed at establishing the role that structural optimization can play in airframe vibrations design work have also been initiated. Five government/industry meetings were held in connection with these activities during the course of the program. Because the DAMVIBS Program is coming to an end, the fifth meeting included a brief assessment of the program and its benefits to the industry.

The NASA/industry design analysis methods for vibrations (DAMVIBS) program: Accomplishments and contributions

NASA Technical Reports Server (NTRS)

Kvaternik, Raymond G.

1991-01-01

A NASA Langley-sponsored rotorcraft structural dynamics program, known as Design Analysis Methods for VIBrationS (DAMVIBS), has been under development since 1984. The objective of this program was to establish the technology base needed by the industry to develop an advanced finite-element-based dynamics design analysis capability for vibrations. Under the program, teams from the four major helicopter manufacturers have formed finite-element models, conducted ground vibration tests, made test/analysis comparisons of both metal and composite airframes, performed 'difficult components' studies on airframes to identify components which need more complete finite-element representation for improved correlation, and evaluated industry codes for computing coupled rotor-airframe vibrations. Studies aimed at establishing the role that structural optimization can play in airframe vibrations design work have also been initiated. Five government/industry meetings were held in connection with these activities during the course of the program. Because the DAMVIBS Program is coming to an end, the fifth meeting included a brief assessment of the program and its benefits to the industry.

Crash Test of Three Cessna 172 Aircraft at NASA Langley Research Center's Landing and Impact Research Facility

NASA Technical Reports Server (NTRS)

Littell, Justin D.

2015-01-01

During the summer of 2015, three Cessna 172 aircraft were crash tested at the Landing and Impact Research Facility (LandIR) at NASA Langley Research Center (LaRC). The three tests simulated three different crash scenarios. The first simulated a flare-to-stall emergency or hard landing onto a rigid surface such as a road or runway, the second simulated a controlled flight into terrain with a nose down pitch on the aircraft, and the third simulated a controlled flight into terrain with an attempt to unsuccessfully recover the aircraft immediately prior to impact, resulting in a tail strike condition. An on-board data acquisition system captured 64 channels of airframe acceleration, along with acceleration and load in two onboard Hybrid II 50th percentile Anthropomorphic Test Devices, representing the pilot and co-pilot. Each test contained different airframe loading conditions and results show large differences in airframe performance. This paper presents test methods used to conduct the crash tests and will summarize the airframe results from the test series.

Full-Scale Crash Test of an MD-500 Helicopter

NASA Technical Reports Server (NTRS)

Littell, Justin

2011-01-01

A full-scale crash test was successfully conducted in March 2010 of an MD-500 helicopter at NASA Langley Research Center s Landing and Impact Research Facility. The reasons for conducting this test were threefold: 1 To generate data to be used with finite element computer modeling efforts, 2 To study the crashworthiness features typically associated with a small representative helicopter, and 3 To compare aircraft response to data collected from a previously conducted MD-500 crash test, which included an externally deployable energy absorbing (DEA) concept. Instrumentation on the airframe included accelerometers on various structural components of the airframe; and strain gages on keel beams, skid gear and portions of the skin. Three Anthropomorphic Test Devices and a specialized Human Surrogate Torso Model were also onboard to collect occupant loads for evaluation with common injury risk criteria. This paper presents background and results from this crash test conducted without the DEA concept. These results showed accelerations of approximately 30 to 50 g on the airframe at various locations, little energy attenuation through the airframe, and moderate to high probability of occupant injury for a variety of injury criteria.

Aerodynamic Database Development for the Hyper-X Airframe Integrated Scramjet Propulsion Experiments

NASA Technical Reports Server (NTRS)

Engelund, Walter C.; Holland, Scott D.; Cockrell, Charles E., Jr.; Bittner, Robert D.

2000-01-01

This paper provides an overview of the activities associated with the aerodynamic database which is being developed in support of NASA's Hyper-X scramjet flight experiments. Three flight tests are planned as part of the Hyper-X program. Each will utilize a small, nonrecoverable research vehicle with an airframe integrated scramjet propulsion engine. The research vehicles will be individually rocket boosted to the scramjet engine test points at Mach 7 and Mach 10. The research vehicles will then separate from the first stage booster vehicle and the scramjet engine test will be conducted prior to the terminal decent phase of the flight. An overview is provided of the activities associated with the development of the Hyper-X aerodynamic database, including wind tunnel test activities and parallel CFD analysis efforts for all phases of the Hyper-X flight tests. A brief summary of the Hyper-X research vehicle aerodynamic characteristics is provided, including the direct and indirect effects of the airframe integrated scramjet propulsion system operation on the basic airframe stability and control characteristics. Brief comments on the planned post flight data analysis efforts are also included.

KENNEDY SPACE CENTER, FLA. - On a tour of the Orbiter Processing Facility, Center Director Jim Kennedy (center) and Deputy Director Woodrow Whitlow Jr. (far left) look at the external tank door corrosion work being done on Endeavour. Next to Whitlow is Bruce Buckingham, assistant to the deputy director. Providing information, at right, are Orbiter Airframe Engineering ground area manager, and Tom Roberts, Airframe Engineering System specialist, both with United Space Alliance; and Joy Huff, with KSC Space Shuttle Processing. Endeavour is in its Orbiter Major Modification period, which began in December 2003.

NASA Image and Video Library

2004-02-25

KENNEDY SPACE CENTER, FLA. - On a tour of the Orbiter Processing Facility, Center Director Jim Kennedy (center) and Deputy Director Woodrow Whitlow Jr. (far left) look at the external tank door corrosion work being done on Endeavour. Next to Whitlow is Bruce Buckingham, assistant to the deputy director. Providing information, at right, are Orbiter Airframe Engineering ground area manager, and Tom Roberts, Airframe Engineering System specialist, both with United Space Alliance; and Joy Huff, with KSC Space Shuttle Processing. Endeavour is in its Orbiter Major Modification period, which began in December 2003.

KENNEDY SPACE CENTER, FLA. - On a tour of the Orbiter Processing Facility, Center Director Jim Kennedy (center) and Deputy Director Woodrow Whitlow Jr. (far left) look at the external tank door corrosion work being done on Endeavour. Next to Whitlow is Bruce Buckingham, assistant to the deputy director. Providing information, at right, are Kathy Laufenberg, Orbiter Airframe Engineering ground area manager, and Tom Roberts, Airframe Engineering System specialist, both with United Space Alliance; and Joy Huff, with Space Shuttle Processing. Endeavour is in its Orbiter Major Modification period, which began in December 2003.

NASA Image and Video Library

2004-02-25

KENNEDY SPACE CENTER, FLA. - On a tour of the Orbiter Processing Facility, Center Director Jim Kennedy (center) and Deputy Director Woodrow Whitlow Jr. (far left) look at the external tank door corrosion work being done on Endeavour. Next to Whitlow is Bruce Buckingham, assistant to the deputy director. Providing information, at right, are Kathy Laufenberg, Orbiter Airframe Engineering ground area manager, and Tom Roberts, Airframe Engineering System specialist, both with United Space Alliance; and Joy Huff, with Space Shuttle Processing. Endeavour is in its Orbiter Major Modification period, which began in December 2003.

Evaluation of the Second Transport Rotorcraft Airframe Crash Testbed (TRACT 2) Full Scale Crash Test

NASA Technical Reports Server (NTRS)

Annett, Martin; Littell, Justin

2015-01-01

Two Transport Rotorcraft Airframe Crash Testbed (TRACT) full-scale tests were performed at NASA Langley Research Center's Landing and Impact Research Facility in 2013 and 2014. Two CH-46E airframes were impacted at 33-ft/s forward and 25-ft/s vertical combined velocities onto soft soil, which represents a severe, but potentially survivable impact scenario. TRACT 1 provided a baseline set of responses, while TRACT 2 included retrofits with composite subfloors and other crash system improvements based on TRACT 1. For TRACT 2, a total of 18 unique experiments were conducted to evaluate ATD responses, seat and restraint performance, cargo restraint effectiveness, patient litter behavior, and activation of emergency locator transmitters and crash sensors. Combinations of Hybrid II, Hybrid III, and ES-2 Anthropomorphic Test Devices (ATDs) were placed in forward and side facing seats and occupant results were compared against injury criteria. The structural response of the airframe was assessed based on accelerometers located throughout the airframe and using three-dimensional photogrammetric techniques. Analysis of the photogrammetric data indicated regions of maximum deflection and permanent deformation. The response of TRACT 2 was noticeably different in the longitudinal direction due to changes in the cabin configuration and soil surface, with higher acceleration and damage occurring in the cabin. Loads from ATDs in energy absorbing seats and restraints were within injury limits. Severe injury was likely for ATDs in forward facing passenger seats.

IMPAC: An Integrated Methodology for Propulsion and Airframe Control

NASA Technical Reports Server (NTRS)

Garg, Sanjay; Ouzts, Peter J.; Lorenzo, Carl F.; Mattern, Duane L.

1991-01-01

The National Aeronautics and Space Administration is actively involved in the development of enabling technologies that will lead towards aircraft with new/enhanced maneuver capabilities such as Short Take-Off Vertical Landing (STOVL) and high angle of attack performance. Because of the high degree of dynamic coupling between the airframe and propulsion systems of these types of aircraft, one key technology is the integration of the flight and propulsion control. The NASA Lewis Research Center approach to developing Integrated Flight Propulsion Control (IFPC) technologies is an in-house research program referred to as IMPAC (Integrated Methodology for Propulsion and Airframe Control). The goals of IMPAC are to develop a viable alternative to the existing integrated control design methodologies that will allow for improved system performance and simplicity of control law synthesis and implementation, and to demonstrate the applicability of the methodology to a supersonic STOVL fighter aircraft. Based on some preliminary control design studies that included evaluation of the existing methodologies, the IFPC design methodology that is emerging at the Lewis Research Center consists of considering the airframe and propulsion system as one integrated system for an initial centralized controller design and then partitioning the centralized controller into separate airframe and propulsion system subcontrollers to ease implementation and to set meaningful design requirements for detailed subsystem control design and evaluation. An overview of IMPAC is provided and detailed discussion of the various important design and evaluation steps in the methodology are included.

New Tool Released for Engine-Airframe Blade-Out Structural Simulations

NASA Technical Reports Server (NTRS)

Lawrence, Charles

2004-01-01

Researchers at the NASA Glenn Research Center have enhanced a general-purpose finite element code, NASTRAN, for engine-airframe structural simulations during steady-state and transient operating conditions. For steady-state simulations, the code can predict critical operating speeds, natural modes of vibration, and forced response (e.g., cabin noise and component fatigue). The code can be used to perform static analysis to predict engine-airframe response and component stresses due to maneuver loads. For transient response, the simulation code can be used to predict response due to bladeoff events and subsequent engine shutdown and windmilling conditions. In addition, the code can be used as a pretest analysis tool to predict the results of the bladeout test required for FAA certification of new and derivative aircraft engines. Before the present analysis code was developed, all the major aircraft engine and airframe manufacturers in the United States and overseas were performing similar types of analyses to ensure the structural integrity of engine-airframe systems. Although there were many similarities among the analysis procedures, each manufacturer was developing and maintaining its own structural analysis capabilities independently. This situation led to high software development and maintenance costs, complications with manufacturers exchanging models and results, and limitations in predicting the structural response to the desired degree of accuracy. An industry-NASA team was formed to overcome these problems by developing a common analysis tool that would satisfy all the structural analysis needs of the industry and that would be available and supported by a commercial software vendor so that the team members would be relieved of maintenance and development responsibilities. Input from all the team members was used to ensure that everyone's requirements were satisfied and that the best technology was incorporated into the code. Furthermore, because the code would be distributed by a commercial software vendor, it would be more readily available to engine and airframe manufacturers, as well as to nonaircraft companies that did not previously have access to this capability.

Aircraft Fuel, Hydraulic and Pneumatic Systems (Course Outlines), Aviation Mechanics 3 (Air Frame): 9067.01.

ERIC Educational Resources Information Center

Dade County Public Schools, Miami, FL.

This document presents an outline for a 135-hour course designed to familiarize the student with the operation, inspection, and repair of aircraft fuel, hydraulic, and pneumatic systems. It is designed to help the trainee master the knowledge and skills necessary to become an aviation airframe mechanic. The aviation airframe maintenance technician…

Aviation Maintenance Technology. Airframe. A203. Aircraft Fabric Covering, Painting, and Finishing. Instructor Material.

ERIC Educational Resources Information Center

Oklahoma State Board of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This teacher's guide is designed to aid teachers in leading students through a module on airframe building and repair, including fabric covering, painting, and finishing. The module contains two units that cover the following topics: (1) inspecting, testing, and installing aircraft fabric coverings and (2) applying dope, paint, and trim. Each unit…

Experimental and analytical investigations to improve low-speed performance and stability and control characteristics of supersonic cruise fighter vehicles

NASA Technical Reports Server (NTRS)

Graham, A. B.

1977-01-01

Small- and large-scale models of supersonic cruise fighter vehicles were used to determine the effectiveness of airframe/propulsion integration concepts for improved low-speed performance and stability and control characteristics. Computer programs were used for engine/airframe sizing studies to yield optimum vehicle performance.

Aviation Maintenance Technology. Airframe. A204. Aircraft Welding. Instructor Material.

ERIC Educational Resources Information Center

Oklahoma State Board of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This teacher's guide is designed to aid teachers in leading students through a module on aircraft welding on airframes. The module contains four units that cover the following topics: (1) gas welding and cutting; (2) brazing and soldering; (3) shielded metal arc welding; and (4) gas tungsten arc welding. Each unit follows a standardized format…

Recent Advances in Structures for Hypersonic Flight, part 2

NASA Technical Reports Server (NTRS)

1978-01-01

The papers at this symposium were presented by 24 speakers representing airframe, missile, and engine manufacturers, the U.S. Air Force, and two NASA Research Centers. The papers cover a variety of topics including engine structures, cooled airframe structures, hot structures, thermal protection systems, cryogenic tankage structures, cryogenic insulations, and analysis methods for thermal/structures.

Fuel Efficiencies Through Airframe Improvements

NASA Technical Reports Server (NTRS)

Bezos-O'Connor, Gaudy M.; Mangelsdorf, Mark F.; Maliska, Heather A.; Washburn, Anthony E.; Wahls, Richard A.

2011-01-01

The factors of continuing strong growth in air traffic volume, the vital role of the air transport system on the economy, and concerns about the environmental impact of aviation have added focus to the National Aeronautics Research Policy. To address these concerns in the context of the National Policy, NASA has set aggressive goals in noise reduction, emissions, and energy consumption. With respect to the goal of reducing energy consumption in the fleet, the development of promising airframe technologies is required to realize the significant improvements that are desired. Furthermore, the combination of advances in materials and structures with aerodynamic technologies may lead to a paradigm shift in terms of potential configurations for the future. Some of these promising airframe technologies targeted at improved efficiency are highlighted.

Airframe-integrated propulsion system for hypersonic cruise vehicles

NASA Technical Reports Server (NTRS)

Jones, R. A.; Huber, P. W.

1978-01-01

The paper describes a new hydrogen-burning airframe-integrated scramjet concept which offers good potential for efficient hypersonic cruise vehicles. The characteristics of the engine which assure good performance are extensive engine-airframe integration, fixed geometry, low cooling, and control of heat release in the supersonic combustor by mixed modes of fuel injection from the combustor entrance. The present paper describes the concept and presents results from inlet tests, direct-connect combustor tests, and tests of two subscale boiler-plate research engines currently underway under conditions which simulate flight at Mach 4 and 7. It is concluded that this engine concept has the potential for high thrust and efficiency, low drag and weight, low cooling requirement, and application to a wide range of vehicle sizes.

Computational Structures Technology for Airframes and Propulsion Systems

NASA Technical Reports Server (NTRS)

Noor, Ahmed K. (Compiler); Housner, Jerrold M. (Compiler); Starnes, James H., Jr. (Compiler); Hopkins, Dale A. (Compiler); Chamis, Christos C. (Compiler)

1992-01-01

This conference publication contains the presentations and discussions from the joint University of Virginia (UVA)/NASA Workshops. The presentations included NASA Headquarters perspectives on High Speed Civil Transport (HSCT), goals and objectives of the UVA Center for Computational Structures Technology (CST), NASA and Air Force CST activities, CST activities for airframes and propulsion systems in industry, and CST activities at Sandia National Laboratory.

Why Has the Cost of Fixed-Wing Aircraft Risen? A Macroscopic Examination of the Trends in U.S. Military Aircraft Costs over the Past Several Decades

DTIC Science & Technology

2008-01-01

simple,” is the share of airframe structure that is neither tita - nium nor composite material. Unfortunately, only 49 of the 93 aircraft with...of airframe materials (or as simpler materials decrease), aircraft unit cost increases. Increasing the proportion of tita - nium and composite

Riding and handling qualities of light aircraft: A review and analysis

NASA Technical Reports Server (NTRS)

Smetana, F. O.; Summery, D. C.; Johnson, W. D.

1972-01-01

Design procedures and supporting data necessary for configuring light aircraft to obtain desired responses to pilot commands and gusts are presented. The procedures employ specializations of modern military and jet transport practice where these provide an improvement over earlier practice. General criteria for riding and handling qualities are discussed in terms of the airframe dynamics. Methods available in the literature for calculating the coefficients required for a linearized analysis of the airframe dynamics are reviewed in detail. The review also treats the relation of spin and stall to airframe geometry. Root locus analysis is used to indicate the sensitivity of airframe dynamics to variations in individual stability derivatives and to variations in geometric parameters. Computer programs are given for finding the frequencies, damping ratios, and time constants of all rigid body modes and for generating time histories of aircraft motions in response to control inputs. Appendices are included presenting the derivation of the linearized equations of motion; the stability derivatives; the transfer functions; approximate solutions for the frequency, damping ratio, and time constants; an indication of methods to be used when linear analysis is inadequate; sample calculations; and an explanation of the use of root locus diagrams and Bode plots.

Advanced Subsonic Airplane Design and Economic Studies

NASA Technical Reports Server (NTRS)

Liebeck, Robert H.; Andrastek, Donald A.; Chau, Johnny; Girvin, Raquel; Lyon, Roger; Rawdon, Blaine K.; Scott, Paul W.; Wright, Robert A.

1995-01-01

A study was made to examine the effect of advanced technology engines on the performance of subsonic airplanes and provide a vision of the potential which these advanced engines offered. The year 2005 was selected as the entry-into-service (EIS) date for engine/airframe combination. A set of four airplane classes (passenger and design range combinations) that were envisioned to span the needs for the 2005 EIS period were defined. The airframes for all classes were designed and sized using 2005 EIS advanced technology. Two airplanes were designed and sized for each class: one using current technology (1995) engines to provide a baseline, and one using advanced technology (2005) engines. The resulting engine/airframe combinations were compared and evaluated on the basis on sensitivity to basic engine performance parameters (e.g. SFC and engine weight) as well as DOC+I. The advanced technology engines provided significant reductions in fuel burn, weight, and wing area. Average values were as follows: reduction in fuel burn = 18%, reduction in wing area = 7%, and reduction in TOGW = 9%. Average DOC+I reduction was 3.5% using the pricing model based on payload-range index and 5% using the pricing model based on airframe weight. Noise and emissions were not considered.

Small Engine Technology (SET). Task 33: Airframe, Integration, and Community Noise Study

NASA Technical Reports Server (NTRS)

Lieber, Lys S.; Elkins, Daniel; Golub, Robert A. (Technical Monitor)

2002-01-01

Task Order 33 had four primary objectives as follows: (1) Identify and prioritize the airframe noise reduction technologies needed to accomplish the NASA Pillar goals for business and regional aircraft. (2) Develop a model to estimate the effect of jet shear layer refraction and attenuation of internally generated source noise of a turbofan engine on the aircraft system noise. (3) Determine the effect on community noise of source noise changes of a generic turbofan engine operating from sea level to 15,000 feet. (4) Support lateral attenuation experiments conducted by NASA Langley at Wallops Island, VA, by coordinating opportunities for Contractor Aircraft to participate as a noise source during the noise measurements. Noise data and noise prediction tools, including airframe noise codes, from the NASA Advanced Subsonic Technology (AST) program were applied to assess the current status of noise reduction technologies relative to the NASA pillar goals for regional and small business jet aircraft. In addition, the noise prediction tools were applied to evaluate the effectiveness of airframe-related noise reduction concepts developed in the AST program on reducing the aircraft system noise. The AST noise data and acoustic prediction tools used in this study were furnished by NASA.

Database of Inlet and Exhaust Noise Shielding for Wedge-Shaped Airframe

NASA Technical Reports Server (NTRS)

Gerhold, Carl H.; Clark, Lorenzo R.

2001-01-01

An experiment to measure the noise shielding of the blended wing body design concept was developed using a simplified wedge-shaped airframe. The experimental study was conducted in the Langley Anechoic Noise Research Facility. A wideband, omnidirective sound source in a simulated engine nacelle was held at locations representative of a range of engine locations above the wing. The sound field around the model was measured with the airframe and source in place and with source alone, using an-array of microphones on a rotating hoop that is also translated along an axis parallel to the airframe axis. The insertion loss was determined from the difference between the two resulting contours. Although no attempt was made to simulate the noise characteristics of a particular engine, the broadband noise source radiated sound over a range of scaled frequencies encompassing 1 and 2 times the blade passage frequency representative of a large, high-bypass-ratio turbofan engine. The measured data show that significant shielding of the inlet-radiated noise is obtained in the area beneath and upstream of the model. The data show the sensitivity of insertion loss to engine location.

Low Noise Cruise Efficient Short Take-Off and Landing Transport Vehicle Study

NASA Technical Reports Server (NTRS)

Kim, Hyun D.; Berton, Jeffrey J.; Jones, Scott M.

2007-01-01

The saturation of the airspace around current airports combined with increasingly stringent community noise limits represents a serious impediment to growth in world aviation travel. Breakthrough concepts that both increase throughput and reduce noise impacts are required to enable growth in aviation markets. Concepts with a 25 year horizon must facilitate a 4x increase in air travel while simultaneously meeting community noise constraints. Attacking these horizon issues holistically is the concept study of a Cruise Efficient Short Take-Off and Landing (CESTOL) high subsonic transport under the NASA's Revolutionary Systems Concepts for Aeronautics (RSCA) project. The concept is a high-lift capable airframe with a partially embedded distributed propulsion system that takes a synergistic approach in propulsion-airframe-integration (PAI) by fully integrating the airframe and propulsion systems to achieve the benefits of both low-noise short take-off and landing (STOL) operations and efficient high speed cruise. This paper presents a summary of the recent study of a distributed propulsion/airframe configuration that provides low-noise STOL operation to enable 24-hour use of the untapped regional and city center airports to increase the capacity of the overall airspace while still maintaining efficient high subsonic cruise flight capability.

Cooling system for high speed aircraft

NASA Technical Reports Server (NTRS)

Lawing, P. L.; Pagel, L. L. (Inventor)

1981-01-01

The system eliminates the necessity of shielding an aircraft airframe constructed of material such as aluminum. Cooling is accomplished by passing a coolant through the aircraft airframe, the coolant acting as a carrier to remove heat from the airframe. The coolant is circulated through a heat pump and a heat exchanger which together extract essentially all of the added heat from the coolant. The heat is transferred to the aircraft fuel system via the heat exchanger and the heat pump. The heat extracted from the coolant is utilized to power the heat pump. The heat pump has associated therewith power turbine mechanism which is also driven by the extracted heat. The power turbines are utilized to drive various aircraft subsystems, the compressor of the heat pump, and provide engine cooling.

Use of system identification techniques for improving airframe finite element models using test data

NASA Technical Reports Server (NTRS)

Hanagud, Sathya V.; Zhou, Weiyu; Craig, James I.; Weston, Neil J.

1991-01-01

A method for using system identification techniques to improve airframe finite element models was developed and demonstrated. The method uses linear sensitivity matrices to relate changes in selected physical parameters to changes in total system matrices. The values for these physical parameters were determined using constrained optimization with singular value decomposition. The method was confirmed using both simple and complex finite element models for which pseudo-experimental data was synthesized directly from the finite element model. The method was then applied to a real airframe model which incorporated all the complexities and details of a large finite element model and for which extensive test data was available. The method was shown to work, and the differences between the identified model and the measured results were considered satisfactory.

Integrated flight/propulsion control system design based on a decentralized, hierarchical approach

NASA Technical Reports Server (NTRS)

Mattern, Duane; Garg, Sanjay; Bullard, Randy

1989-01-01

A sample integrated flight/propulsion control system design is presented for the piloted longitudinal landing task with a modern, statistically unstable fighter aircraft. The design procedure is summarized. The vehicle model used in the sample study is described, and the procedure for partitioning the integrated system is presented along with a description of the subsystems. The high-level airframe performance specifications and control design are presented and the control performance is evaluated. The generation of the low-level (engine) subsystem specifications from the airframe requirements are discussed, and the engine performance specifications are presented along with the subsystem control design. A compensator to accommodate the influence of airframe outputs on the engine subsystem is also considered. Finally, the entire closed loop system performance and stability characteristics are examined.

Integrated flight/propulsion control system design based on a decentralized, hierarchical approach

NASA Technical Reports Server (NTRS)

Mattern, Duane; Garg, Sanjay; Bullard, Randy

1989-01-01

A sample integrated flight/propulsion control system design is presented for the piloted longitiudinal landing task with a modern, statistically unstable fighter aircraft. The design procedure is summarized, the vehicle model used in the sample study is described, and the procedure for partitioning the integrated system is presented along with a description of the subsystems. The high-level airframe performance specifications and control design are presented and the control performance is evaluated. The generation of the low-level (engine) subsystem specifications from the airframe requirements are discussed, and the engine performance specifications are presented along with the subsystem control design. A compensator to accommodate the influence of airframe outputs on the engine subsystem is also considered. Finally, the entire closed loop system performance and stability characteristics are examined.

The NASA/industry Design Analysis Methods for Vibrations (DAMVIBS) program: McDonnell-Douglas Helicopter Company achievements

NASA Technical Reports Server (NTRS)

Toossi, Mostafa; Weisenburger, Richard; Hashemi-Kia, Mostafa

1993-01-01

This paper presents a summary of some of the work performed by McDonnell Douglas Helicopter Company under NASA Langley-sponsored rotorcraft structural dynamics program known as DAMVIBS (Design Analysis Methods for VIBrationS). A set of guidelines which is applicable to dynamic modeling, analysis, testing, and correlation of both helicopter airframes and a large variety of structural finite element models is presented. Utilization of these guidelines and the key features of their applications to vibration modeling of helicopter airframes are discussed. Correlation studies with the test data, together with the development and applications of a set of efficient finite element model checkout procedures, are demonstrated on a large helicopter airframe finite element model. Finally, the lessons learned and the benefits resulting from this program are summarized.

Evaluation of the First Transport Rotorcraft Airframe Crash Testbed (TRACT 1) Full-Scale Crash Test

NASA Technical Reports Server (NTRS)

Annett, Martin S.; Littell, Justin D.; Jackson, Karen E.; Bark, Lindley W.; DeWeese, Rick L.; McEntire, B. Joseph

2014-01-01

In 2012, the NASA Rotary Wing Crashworthiness Program initiated the Transport Rotorcraft Airframe Crash Testbed (TRACT) research program by obtaining two CH-46E helicopters from the Navy CH-46E Program Office (PMA-226) at the Navy Flight Readiness Center in Cherry Point, North Carolina. Full-scale crash tests were planned to assess dynamic responses of transport-category rotorcraft under combined horizontal and vertical impact loading. The first crash test (TRACT 1) was performed at NASA Langley Research Center's Landing and Impact Research Facility (LandIR), which enables the study of critical interactions between the airframe, seat, and occupant during a controlled crash environment. The CH-46E fuselage is categorized as a medium-lift rotorcraft with fuselage dimensions comparable to a regional jet or business jet. The first TRACT test (TRACT 1) was conducted in August 2013. The primary objectives for TRACT 1 were to: (1) assess improvements to occupant loads and displacement with the use of crashworthy features such as pre-tensioning active restraints and energy absorbing seats, (2) develop novel techniques for photogrammetric data acquisition to measure occupant and airframe kinematics, and (3) provide baseline data for future comparison with a retrofitted airframe configuration. Crash test conditions for TRACT 1 were 33-ft/s forward and 25-ft/s vertical combined velocity onto soft soil, which represent a severe, but potentially survivable impact scenario. The extraordinary value of the TRACT 1 test was reflected by the breadth of meaningful experiments. A total of 8 unique experiments were conducted to evaluate ATD responses, seat and restraint performance, cargo restraint effectiveness, patient litter behavior, and photogrammetric techniques. A combination of Hybrid II, Hybrid III, and ES-2 Anthropomorphic Test Devices (ATDs) were placed in forward and side facing seats and occupant results were compared against injury criteria. Loads from ATDs in energy absorbing seats and restraints were within injury limits. Severe injury was likely for ATDs in forward facing passenger seats, legacy troop bench seats, and a three-tiered patient litter. In addition, two standing ATDs were used to evaluate the benefit of Mobile Aircrew Restraint Systems (MARS) versus a standard gunner's belt. The ATD with the MARS survived the impact, while fatal head blunt trauma occurred for the standing ATD held by the legacy gunner's belt. In addition to occupant loading, the structural response of the airframe was assessed based on accelerometers located throughout the airframe and using three-dimensional photogrammetric techniques. Analysis of the photogrammetric data indicated regions of maximum deflection and permanent deformation.

Design of an integrated airframe/propulsion control system architecture

NASA Technical Reports Server (NTRS)

Cohen, Gerald C.; Lee, C. William; Strickland, Michael J.

1990-01-01

The design of an integrated airframe/propulsion control system architecture is described. The design is based on a prevalidation methodology that used both reliability and performance tools. An account is given of the motivation for the final design and problems associated with both reliability and performance modeling. The appendices contain a listing of the code for both the reliability and performance model used in the design.

Autonomous Aerodynamic Control of Micro Air Vehicles

DTIC Science & Technology

2009-10-19

Wind tunnel studies have also begun in which detailed aerodynamic quantification can be mad regarding MAV performance with flexible airframes...research. The design is similar to existing MAVs. The airframe has a conventional aircraft design to allow for easy determination of aerodynamic...exceeded in normal flight by conventional aircraft ; however, it is not uncommon for a MAV to surpass the limits due to its low inertia. While collecting

Crash Test of an MD-500 Helicopter with a Deployable Energy Absorber Concept

NASA Technical Reports Server (NTRS)

Littell, Justin D.; Jackson, Karen E.; Kellas, Sotiris

2010-01-01

On December 2, 2009, a full scale crash test was successfully conducted of a MD-500 helicopter at the NASA Langley Research Center Landing and Impact Research Facility . The purpose of this test was to evaluate a novel composite honeycomb deployable energy absorbing (DEA) concept for attenuation of structural and crew loads during helicopter crashes under realistic crash conditions. The DEA concept is an alternative to external airbags, and absorbs impact energy through crushing. In the test, the helicopter impacted the concrete surface with 11.83 m/s (38.8 ft/s) horizontal, 7.80 m/s (25.6 ft/s) vertical and 0.15 m/s (0.5 ft/s) lateral velocities; corresponding to a resultant velocity of 14.2 m/s (46.5 ft/s). The airframe and skid gear were instrumented with accelerometers and strain gages to determine structural integrity and load attenuation, while the skin of the airframe was covered with targets for use by photogrammetry to record gross vehicle motion before, during, and after the impact. Along with the collection of airframe data, one Hybrid III 50th percentile anthropomorphic test device (ATD), two Hybrid II 50th percentile ATDs and a specialized human surrogate torso model (HSTM) occupant were seated in the airframe and instrumented for the collection of occupant loads. Resultant occupant data showed that by using the DEA, the loads on the Hybrid II and Hybrid III ATDs were in the Low Risk regime for the injury criteria, while structural data showed the airframe retained its structural integrity post crash. Preliminary results show that the DEA is a viable concept for the attenuation of impact loads.

System Noise Assessment and the Potential for a Low Noise Hybrid Wing Body Aircraft with Open Rotor Propulsion

NASA Technical Reports Server (NTRS)

Thomas, Russell H.; Burley, Casey L.; Lopes, Leonard V.; Bahr, Christopher J.; Gern, Frank H.; VanZante, Dale E.

2014-01-01

An aircraft system noise assessment was conducted for a hybrid wing body freighter aircraft concept configured with three open rotor engines. The primary objective of the study was to determine the aircraft system level noise given the significant impact of installation effects including shielding the open rotor noise by the airframe. The aircraft was designed to carry a payload of 100,000 lbs on a 6,500 nautical mile mission. An experimental database was used to establish the propulsion airframe aeroacoustic installation effects including those from shielding by the airframe planform, interactions with the control surfaces, and additional noise reduction technologies. A second objective of the study applied the impacts of projected low noise airframe technology and a projection of advanced low noise rotors appropriate for the NASA N+2 2025 timeframe. With the projection of low noise rotors and installation effects, the aircraft system level was 26.0 EPNLdB below Stage 4 level with the engine installed at 1.0 rotor diameters upstream of the trailing edge. Moving the engine to 1.5 rotor diameters brought the system level noise to 30.8 EPNLdB below Stage 4. At these locations on the airframe, the integrated level of installation effects including shielding can be as much as 20 EPNLdB cumulative in addition to lower engine source noise from advanced low noise rotors. And finally, an additional set of technology effects were identified and the potential impact at the system level was estimated for noise only without assessing the impact on aircraft performance. If these additional effects were to be included it is estimated that the potential aircraft system noise could reach as low as 38.0 EPNLdB cumulative below Stage 4.

Use of system identification techniques for improving airframe finite element models using test data

NASA Technical Reports Server (NTRS)

Hanagud, Sathya V.; Zhou, Weiyu; Craig, James I.; Weston, Neil J.

1993-01-01

A method for using system identification techniques to improve airframe finite element models using test data was developed and demonstrated. The method uses linear sensitivity matrices to relate changes in selected physical parameters to changes in the total system matrices. The values for these physical parameters were determined using constrained optimization with singular value decomposition. The method was confirmed using both simple and complex finite element models for which pseudo-experimental data was synthesized directly from the finite element model. The method was then applied to a real airframe model which incorporated all of the complexities and details of a large finite element model and for which extensive test data was available. The method was shown to work, and the differences between the identified model and the measured results were considered satisfactory.

A Data System for a Rapid Evaluation Class of Subscale Aerial Vehicle

NASA Technical Reports Server (NTRS)

Hogge, Edward F.; Quach, Cuong C.; Vazquez, Sixto L.; Hill, Boyd L.

2011-01-01

A low cost, rapid evaluation, test aircraft is used to develop and test airframe damage diagnosis algorithms at Langley Research Center as part of NASA's Aviation Safety Program. The remotely operated subscale aircraft is instrumented with sensors to monitor structural response during flight. Data is collected for good and compromised airframe configurations to develop data driven models for diagnosing airframe state. This paper describes the data acquisition system (DAS) of the rapid evaluation test aircraft. A PC/104 form factor DAS was developed to allow use of Matlab, Simulink simulation code in Langley's existing subscale aircraft flight test infrastructure. The small scale of the test aircraft permitted laboratory testing of the actual flight article under controlled conditions. The low cost and modularity of the DAS permitted adaptation to various flight experiment requirements.

The Official Home Page of the U.S. Air Force

Science.gov Websites

: May 24 Air Force directs one-day operational safety review SecAF LOI SecAF LOI Letter of Intent AF and members using two C-130 and one C-17 training airframes. (U.S. Air Force photo by Richard Eldridge) The Transport Team crew members using two C-130 and one C-17 training airframes. (U.S. Air Force photo by

Aircraft Engine Exhaust Nozzle System for Jet Noise Reduction

NASA Technical Reports Server (NTRS)

Thomas, Russell H. (Inventor); Czech, Michael J. (Inventor); Elkoby, Ronen (Inventor)

2014-01-01

The aircraft exhaust engine nozzle system includes a fan nozzle to receive a fan flow from a fan disposed adjacent to an engine disposed above an airframe surface of the aircraft, a core nozzle disposed within the fan nozzle and receiving an engine core flow, and a pylon structure connected to the core nozzle and structurally attached with the airframe surface to secure the engine to the aircraft.

Analysis of small crack behavior for airframe applications

NASA Technical Reports Server (NTRS)

Mcclung, R. C.; Chan, K. S.; Hudak, S. J., Jr.; Davidson, D. L.

1994-01-01

The small fatigue crack problem is critically reviewed from the perspective of airframe applications. Different types of small cracks-microstructural, mechanical, and chemical-are carefully defined and relevant mechanisms identified. Appropriate analysis techniques, including both rigorous scientific and practical engineering treatments, are briefly described. Important materials data issues are addressed, including increased scatter in small crack data and recommended small crack test methods. Key problems requiring further study are highlighted.

Distributed Propulsion Vehicles

NASA Technical Reports Server (NTRS)

Kim, Hyun Dae

2010-01-01

Since the introduction of large jet-powered transport aircraft, the majority of these vehicles have been designed by placing thrust-generating engines either under the wings or on the fuselage to minimize aerodynamic interactions on the vehicle operation. However, advances in computational and experimental tools along with new technologies in materials, structures, and aircraft controls, etc. are enabling a high degree of integration of the airframe and propulsion system in aircraft design. The National Aeronautics and Space Administration (NASA) has been investigating a number of revolutionary distributed propulsion vehicle concepts to increase aircraft performance. The concept of distributed propulsion is to fully integrate a propulsion system within an airframe such that the aircraft takes full synergistic benefits of coupling of airframe aerodynamics and the propulsion thrust stream by distributing thrust using many propulsors on the airframe. Some of the concepts are based on the use of distributed jet flaps, distributed small multiple engines, gas-driven multi-fans, mechanically driven multifans, cross-flow fans, and electric fans driven by turboelectric generators. This paper describes some early concepts of the distributed propulsion vehicles and the current turboelectric distributed propulsion (TeDP) vehicle concepts being studied under the NASA s Subsonic Fixed Wing (SFW) Project to drastically reduce aircraft-related fuel burn, emissions, and noise by the year 2030 to 2035.

Impact Testing and Simulation of Composite Airframe Structures

NASA Technical Reports Server (NTRS)

Jackson, Karen E.; Littell, Justin D.; Horta, Lucas G.; Annett, Martin S.; Fasanella, Edwin L.; Seal, Michael D., II

2014-01-01

Dynamic tests were performed at NASA Langley Research Center on composite airframe structural components of increasing complexity to evaluate their energy absorption behavior when subjected to impact loading. A second objective was to assess the capabilities of predicting the dynamic response of composite airframe structures, including damage initiation and progression, using a state-of-the-art nonlinear, explicit transient dynamic finite element code, LS-DYNA. The test specimens were extracted from a previously tested composite prototype fuselage section developed and manufactured by Sikorsky Aircraft Corporation under the US Army's Survivable Affordable Repairable Airframe Program (SARAP). Laminate characterization testing was conducted in tension and compression. In addition, dynamic impact tests were performed on several components, including I-beams, T-sections, and cruciform sections. Finally, tests were conducted on two full-scale components including a subfloor section and a framed fuselage section. These tests included a modal vibration and longitudinal impact test of the subfloor section and a quasi-static, modal vibration, and vertical drop test of the framed fuselage section. Most of the test articles were manufactured of graphite unidirectional tape composite with a thermoplastic resin system. However, the framed fuselage section was constructed primarily of a plain weave graphite fabric material with a thermoset resin system. Test data were collected from instrumentation such as accelerometers and strain gages and from full-field photogrammetry.

The NASA/industry Design Analysis Methods for Vibrations (DAMVIBS) program : Bell Helicopter Textron accomplishments

NASA Technical Reports Server (NTRS)

Cronkhite, James D.

1993-01-01

Accurate vibration prediction for helicopter airframes is needed to 'fly from the drawing board' without costly development testing to solve vibration problems. The principal analytical tool for vibration prediction within the U.S. helicopter industry is the NASTRAN finite element analysis. Under the NASA DAMVIBS research program, Bell conducted NASTRAN modeling, ground vibration testing, and correlations of both metallic (AH-1G) and composite (ACAP) airframes. The objectives of the program were to assess NASTRAN airframe vibration correlations, to investigate contributors to poor agreement, and to improve modeling techniques. In the past, there has been low confidence in higher frequency vibration prediction for helicopters that have multibladed rotors (three or more blades) with predominant excitation frequencies typically above 15 Hz. Bell's findings under the DAMVIBS program, discussed in this paper, included the following: (1) accuracy of finite element models (FEM) for composite and metallic airframes generally were found to be comparable; (2) more detail is needed in the FEM to improve higher frequency prediction; (3) secondary structure not normally included in the FEM can provide significant stiffening; (4) damping can significantly affect phase response at higher frequencies; and (5) future work is needed in the areas of determination of rotor-induced vibratory loads and optimization.

The Shock and Vibration Bulletin. Part 1. Welcome, Keynote Address, Invited Papers, Pyrotechnic Shock, and Shock Testing and Analysis

DTIC Science & Technology

1983-05-01

DESIGN PROCEDURE M. S. IIAndal, University of Vermont, Burlington, VT Machinery Dynamics ANALYTICAL AND EXPERIMENTAL INVESTIGATION OF ROTATING BLADE... methodology to accurately predict rotor vibratory loads and has recently been initiated for detail design and bench test- coupled rotor/airframe vibrations... design methodology , a trating on the basic disciplines of aerodynamics and struc. coupled rotor/airframe vibration analysis has been developed. tural

A verification procedure for MSC/NASTRAN Finite Element Models

NASA Technical Reports Server (NTRS)

Stockwell, Alan E.

1995-01-01

Finite Element Models (FEM's) are used in the design and analysis of aircraft to mathematically describe the airframe structure for such diverse tasks as flutter analysis and actively controlled landing gear design. FEM's are used to model the entire airplane as well as airframe components. The purpose of this document is to describe recommended methods for verifying the quality of the FEM's and to specify a step-by-step procedure for implementing the methods.

Decentralized hierarchical partitioning of centralized integrated controllers. [for flight propulsion in STOVLs

NASA Technical Reports Server (NTRS)

Schmidt, Phillip; Garg, Sanjay

1991-01-01

A framework for a decentralized hierarchical controller partitioning structure is developed. This structure allows for the design of separate airframe and propulsion controllers which, when assembled, will meet the overall design criterion for the integrated airframe/propulsion system. An algorithm based on parameter optimization of the state-space representation for the subsystem controllers is described. The algorithm is currently being applied to an integrated flight propulsion control design example.

Gain selection method and model for coupled propulsion and airframe systems

NASA Technical Reports Server (NTRS)

Murphy, P. C.

1982-01-01

A longitudinal model is formulated for an advanced fighter from three subsystem models: the inlet, the engine, and the airframe. Notable interaction is found in the coupled system. A procedure, based on eigenvalue sensitivities, is presented which indicates the importance of the feedback gains to the optimal solution. This allows ineffectual gains to be eliminated; thus, hardware and expense may be saved in the realization of the physical controller.

Advanced general aviation engine/airframe integration study

NASA Technical Reports Server (NTRS)

Zmroczek, L. A.

1982-01-01

A comparison of the in-airframe performance and efficiency of the advanced engine concepts is presented. The results indicate that the proposed advanced engines can significantly improve the performance and economy of general aviation airplanes. The engine found to be most promising is the highly advanced version of a rotary combustion (Wankel) engine. The low weight and fuel consumption of this engine, as well as its small size, make it suited for aircraft use.

Development and application of a technique for reducing airframe finite element models for dynamics analysis

NASA Technical Reports Server (NTRS)

Hashemi-Kia, Mostafa; Toossi, Mostafa

1990-01-01

A computational procedure for the reduction of large finite element models was developed. This procedure is used to obtain a significantly reduced model while retaining the essential global dynamic characteristics of the full-size model. This reduction procedure is applied to the airframe finite element model of AH-64A Attack Helicopter. The resulting reduced model is then validated by application to a vibration reduction study.

Airframe integration trade studies for a reusable launch vehicle

NASA Astrophysics Data System (ADS)

Dorsey, John T.; Wu, Chauncey; Rivers, Kevin; Martin, Carl; Smith, Russell

1999-01-01

Future launch vehicles must be lightweight, fully reusable and easily maintained if low-cost access to space is to be achieved. The goal of achieving an economically viable Single-Stage-to-Orbit (SSTO) Reusable Launch Vehicle (RLV) is not easily achieved and success will depend to a large extent on having an integrated and optimized total system. A series of trade studies were performed to meet three objectives. First, to provide structural weights and parametric weight equations as inputs to configuration-level trade studies. Second, to identify, assess and quantify major weight drivers for the RLV airframe. Third, using information on major weight drivers, and considering the RLV as an integrated thermal structure (composed of thrust structures, tanks, thermal protection system, insulation and control surfaces), identify and assess new and innovative approaches or concepts that have the potential for either reducing airframe weight, improving operability, and/or reducing cost.

Experimental investigation of active loads control for aircraft landing gear

NASA Technical Reports Server (NTRS)

Mcgehee, J. R.; Dreher, R. C.

1982-01-01

Aircraft dynamic loads and vibrations resulting from landing impact and from runway and taxiway unevenness are recognized as significant in causing fatigue damage, dynamic stress on the airframe, crew and passenger discomfort, and reduction of the pilot's ability to control the aircraft during ground operations. One potential method for improving operational characteistics of aircraft on the ground is the application of active control technology to the landing gears to reduce ground loads applied to the airframe. An experimental investigation was conducted which simulated the landing dynamics of a light airplane to determine the feasibility and potential of a series hydraulic active control main landing gear. The experiments involved a passive gear and an active control gear. Results of this investigation show that a series hydraulically controlled gear is feasible and that such a gear is very effective in reducing the loads transmitted by the gear to the airframe during ground operations.

Airframe Integration Trade Studies for a Reusable Launch Vehicle

NASA Technical Reports Server (NTRS)

Dorsey, John T.; Wu, Chauncey; Rivers, Kevin; Martin, Carl; Smith, Russell

1999-01-01

Future launch vehicles must be lightweight, fully reusable and easily maintained if low-cost access to space is to be achieved. The goal of achieving an economically viable Single-Stage-to-Orbit (SSTO) Reusable Launch Vehicle (RLV) is not easily achieved and success will depend to a large extent on having an integrated and optimized total system. A series of trade studies were performed to meet three objectives. First, to provide structural weights and parametric weight equations as inputs to configuration-level trade studies. Second, to identify, assess and quantify major weight drivers for the RLV airframe. Third, using information on major weight drivers, and considering the RLV as an integrated thermal structure (composed of thrust structures, tanks, thermal protection system, insulation and control surfaces), identify and assess new and innovative approaches or concepts that have the potential for either reducing airframe weight, improving operability, and/or reducing cost.

NASA's Quiet Aircraft Technology Project

NASA Technical Reports Server (NTRS)

Whitfield, Charlotte E.

2004-01-01

NASA's Quiet Aircraft Technology Project is developing physics-based understanding, models and concepts to discover and realize technology that will, when implemented, achieve the goals of a reduction of one-half in perceived community noise (relative to 1997) by 2007 and a further one-half in the far term. Noise sources generated by both the engine and the airframe are considered, and the effects of engine/airframe integration are accounted for through the propulsion airframe aeroacoustics element. Assessments of the contribution of individual source noise reductions to the reduction in community noise are developed to guide the work and the development of new tools for evaluation of unconventional aircraft is underway. Life in the real world is taken into account with the development of more accurate airport noise models and flight guidance methodology, and in addition, technology is being developed that will further reduce interior noise at current weight levels or enable the use of lighter-weight structures at current noise levels.

The Integrated Airframe/Propulsion Control System Architecture program (IAPSA)

NASA Technical Reports Server (NTRS)

Palumbo, Daniel L.; Cohen, Gerald C.; Meissner, Charles W.

1990-01-01

The Integrated Airframe/Propulsion Control System Architecture program (IAPSA) is a two-phase program which was initiated by NASA in the early 80s. The first phase, IAPSA 1, studied different architectural approaches to the problem of integrating engine control systems with airframe control systems in an advanced tactical fighter. One of the conclusions of IAPSA 1 was that the technology to construct a suitable system was available, yet the ability to create these complex computer architectures has outpaced the ability to analyze the resulting system's performance. With this in mind, the second phase of IAPSA approached the same problem with the added constraint that the system be designed for validation. The intent of the design for validation requirement is that validation requirements should be shown to be achievable early in the design process. IAPSA 2 has demonstrated that despite diligent efforts, integrated systems can retain characteristics which are difficult to model and, therefore, difficult to validate.

CFD Assessment of Aerodynamic Degradation of a Subsonic Transport Due to Airframe Damage

NASA Technical Reports Server (NTRS)

Frink, Neal T.; Pirzadeh, Shahyar Z.; Atkins, Harold L.; Viken, Sally A.; Morrison, Joseph H.

2010-01-01

A computational study is presented to assess the utility of two NASA unstructured Navier-Stokes flow solvers for capturing the degradation in static stability and aerodynamic performance of a NASA General Transport Model (GTM) due to airframe damage. The approach is to correlate computational results with a substantial subset of experimental data for the GTM undergoing progressive losses to the wing, vertical tail, and horizontal tail components. The ultimate goal is to advance the probability of inserting computational data into the creation of advanced flight simulation models of damaged subsonic aircraft in order to improve pilot training. Results presented in this paper demonstrate good correlations with slope-derived quantities, such as pitch static margin and static directional stability, and incremental rolling moment due to wing damage. This study further demonstrates that high fidelity Navier-Stokes flow solvers could augment flight simulation models with additional aerodynamic data for various airframe damage scenarios.

Computational Modeling of a Mechanized Benchtop Apparatus for Leading-Edge Slat Noise Treatment Device Prototypes

NASA Technical Reports Server (NTRS)

Turner, Travis L.; Moore, James B.; Long, David L.

2017-01-01

Airframe noise is a growing concern in the vicinity of airports because of population growth and gains in engine noise reduction that have rendered the airframe an equal contributor during the approach and landing phases of flight for many transport aircraft. The leading-edge-slat device of a typical high-lift system for transport aircraft is a prominent source of airframe noise. Two technologies have significant potential for slat noise reduction; the slat-cove filler (SCF) and the slat-gap filler (SGF). Previous work was done on a 2D section of a transport-aircraft wing to demonstrate the implementation feasibility of these concepts. Benchtop hardware was developed in that work for qualitative parametric study. The benchtop models were mechanized for quantitative measurements of performance. Computational models of the mechanized benchtop apparatus for the SCF were developed and the performance of the system for five different SCF assemblies is demonstrated.

Airframe Noise Reduction Studies and Clean-Airframe Noise Investigation

NASA Technical Reports Server (NTRS)

Fink, M. R.; Bailey, D. A.

1980-01-01

Acoustic wind tunnel tests were conducted of a wing model with modified leading edge slat and trailing edge flap. The modifications were intended to reduce the surface pressure response to convected turbulence and thereby reduce the airframe noise without changing the lift at constant incidence. Tests were conducted at 70.7 and 100 m/sec airspeeds, with Reynolds numbers 1.5 x 10 to the 6th power and 2.1 x 10 to the 6th power. Considerable reduction of noise radiation from the side edges of a 40 deflection single slotted flap was achieved by modification to the side edge regions or the leading edge region of the flap panel. Total far field noise was reduced 2 to 3 dB over several octaves of frequency. When these panels were installed as the aft panel of a 40 deg deflection double slotted flap, 2 dB noise reduction was achieved.

User's manual for the coupled rotor/airframe vibration analysis graphic package

NASA Technical Reports Server (NTRS)

Studwell, R. E.

1982-01-01

User instructions for a graphics package for coupled rotor/airframe vibration analysis are presented. Responses to plot package messages which the user must make to activate plot package operations and options are described. Installation instructions required to set up the program on the CDC system are included. The plot package overlay structure and subroutines which have to be modified for the CDC system are also described. Operating instructions for CDC applications are included.

Study to Improve Airframe Turbine Engine Rotor Blade Containment

DTIC Science & Technology

1977-07-01

REPORT NO. FAA-RD-77-44 ( DOT-FA76WA-3843 JUNE 1976 STUDY TO IMPROVE AIRFRAME TURBINE ENGINE ROTOR BLADE CONTAINMENT C. 0. GUNDERSON SOF Tftj. -" So...both engines appeared to be able to marginally contain the 1 and 2 blade fragments in all compressor and turbine stages, but probably would rfiot have...adjacent blades including serrations from any stage. The investigation was made on high bypass ratio turbofan engines which power wide body transports

NASA Airframe Icing Research Overview Past and Current

NASA Technical Reports Server (NTRS)

Potapczuk, Mark

2009-01-01

This slide presentation reviews the past and current research that NASA has done in the area of airframe icing. Both the history experimental efforts and model development to understand the process and problem of ice formation are reviewed. This has resulted in the development of new experimental methods, advanced icing simulation software, flight dynamics and experimental databases that have an impact on design, testing, construction and certification and qualification of the aircraft and its sub-systems.

Prime Contract Awards Over $25,000 by Major System, Contractor and State, FY83.

DTIC Science & Technology

1983-01-01

SERVICES 3,074 VO R513 STUDIES/FEASIBILITY - NON- CONSTRUCTION 125 VO T013 TECHNICAL WRITING 1,347 VO 1560 AIRFRAME STRUCTURAL COMPONENTS 6,825 VO 1620...INC NCAR 1670 PARACHUTES RECOVERY SYS AND TIE DOWN EQ 49 ROCKWELL INTERNATIONAL CORP CALIF Y19 CONSTR: CONSTRUCTION /OTHER AIRFIELD STRUCTURES 28,480...INC NEW Y 1560 AIRFRAME STRUCTURAL COMPONENTS 36 GANAR INDUSTRIES I NC CALIF 1680 MISCL AIRCRAFT ACCESSORIES COMPONENTS 180 GARRETT CONSTRUCTION CO

Aerothermodynamic flow phenomena of the airframe-integrated supersonic combustion ramjet

NASA Technical Reports Server (NTRS)

Walton, James T.

1992-01-01

The unique component flow phenomena is discussed of the airframe-integrated supersonic combustion ramjet (scramjet) in a format geared towards new players in the arena of hypersonic propulsion. After giving an overview of the scramjet aerothermodynamic cycle, the characteristics are then covered individually of the vehicle forebody, inlet, combustor, and vehicle afterbody/nozzle. Attention is given to phenomena such as inlet speeding, inlet starting, inlet spillage, fuel injection, thermal choking, and combustor-inlet interaction.

Supersonic Cruise Research 1979, part 2. [airframe structures and materials, systems integration, economic analysis

NASA Technical Reports Server (NTRS)

1980-01-01

Advances in airframe structure and materials technology for supersonic cruise aircraft are reported with emphasis on titanium and composite structures. The operation of the Concorde is examined as a baseline for projections into the future. A market survey of U.S. passenger attitudes and preferences, the impact of advanced air transport technology and the integration of systems for the advanced SST and for a smaller research/business jet vehicle are also discussed.

Aircraft Airframe Cost Estimation Using a Random Coefficients Model

DTIC Science & Technology

1979-12-01

approach will also be used here. 2 Model Formulation Several different types of equations could be used for the basic form of the CER, such as linear ...5) Marcotte developed several CER’s for fighter aircraft airframes using the log- linear model . A plot of the residuals from the CER for recurring...of the natural logarithm. Ordinary Least Squares The ordinary least squares procedure starts with the equation for the general linear model . The

Fluidic actuators for active flow control on airframe

NASA Astrophysics Data System (ADS)

Schueller, M.; Weigel, P.; Lipowski, M.; Meyer, M.; Schlösser, P.; Bauer, M.

2016-04-01

One objective of the European Projects AFLoNext and Clean Sky 2 is to apply Active Flow Control (AFC) on the airframe in critical aerodynamic areas such as the engine/wing junction or the outer wing region for being able to locally improve the aerodynamics in certain flight conditions. At the engine/wing junction, AFC is applied to alleviate or even eliminate flow separation at low speeds and high angle of attacks likely to be associated with the integration of underwing- mounted Ultra High Bypass Ratio (UHBR) engines and the necessary slat-cut-outs. At the outer wing region, AFC can be used to allow more aggressive future wing designs with improved performance. A relevant part of the work on AFC concepts for airframe application is the development of suitable actuators. Fluidic Actuated Flow Control (FAFC) has been introduced as a Flow Control Technology that influences the boundary layer by actively blowing air through slots or holes out of the aircraft skin. FAFC actuators can be classified by their Net Mass Flux and accordingly divided into ZNMF (Zero Net Mass Flux) and NZNMF (Non Zero Net-Mass-Flux) actuators. In the frame of both projects, both types of the FAFC actuator concepts are addressed. In this paper, the objectives of AFC on the airframe is presented and the actuators that are used within the project are discussed.

Investigation of difficult component effects on finite element model vibration prediction for the Bell AG-1G helicopter. Volume 2: Correlation results

NASA Technical Reports Server (NTRS)

Dompka, R. V.

1989-01-01

Under the NASA-sponsored DAMVIBS (Design Analysis Methods for VIBrationS) program, a series of ground vibration tests and NASTRAN finite element model (FEM) correlations were conducted on the Bell AH-1G helicopter gunship to investigate the effects of difficult components on the vibration response of the airframe. Previous correlations of the AG-1G showed good agreement between NASTRAN and tests through 15 to 20 Hz, but poor agreement in the higher frequency range of 20 to 30 Hz. Thus, this effort emphasized the higher frequency airframe vibration response correlations and identified areas that need further R and T work. To conduct the investigations, selected difficult components (main rotor pylon, secondary structure, nonstructural doors/panels, landing gear, engine, furl, etc.) were systematically removed to quantify their effects on overall vibratory response of the airframe. The entire effort was planned and documented, and the results reviewed by NASA and industry experts in order to ensure scientific control of the testing, analysis, and correlation exercise. In particular, secondary structure and damping had significant effects on the frequency response of the airframe above 15 Hz. Also, the nonlinear effects of thrust stiffening and elastomer mounts were significant on the low frequency pylon modes below main rotor 1p (5.4 Hz). The results of the NASTRAN FEM correlations are given.

Investigation of difficult component effects on finite element model vibration prediction for the Bell AH-1G helicopter. Volume 1: Ground vibration test results

NASA Technical Reports Server (NTRS)

Dompka, R. V.

1989-01-01

Under the NASA-sponsored Design Analysis Methods for VIBrationS (DAMVIBS) program, a series of ground vibration tests and NASTRAN finite element model (FEM) correlations were conducted on the Bell AH-1G helicopter gunship to investigate the effects of difficult components on the vibration response of the airframe. Previous correlations of the AH-1G showed good agreement between NASTRAN and tests through 15 to 20 Hz, but poor agreement in the higher frequency range of 20 to 30 Hz. Thus, this effort emphasized the higher frequency airframe vibration response correlations and identified areas that need further R and T work. To conduct the investigations, selected difficult components (main rotor pylon, secondary structure, nonstructural doors/panels, landing gear, engine, fuel, etc.) were systematically removed to quantify their effects on overall vibratory response of the airframe. The entire effort was planned and documented, and the results reviewed by NASA and industry experts in order to ensure scientific control of the testing, analysis, and correlation exercise. In particular, secondary structure and damping had significant effects on the frequency response of the airframe above 15 Hz. Also, the nonlinear effects of thrust stiffening and elastomer mounts were significant on the low frequency pylon modes below main rotor 1p (5.4 Hz). The results of the ground vibration testing are presented.

Innovative Approaches to Flaw-Tolerant Design and Certification of Airframe Components. Report on NACA Data- Task 6

DTIC Science & Technology

2017-10-16

parameter A3 of the design curve is negative for 24S-T3. The design curve shown in Figure 41 for Model S2 is comparable with the design curve shown...Approaches to Flaw-Tolerant Design and Certification of Airframe Components Report on NACA Data – Task 6 Ricardo Actis and Barna Szabó Engineering...Software Research and Development, Inc. 111 West Port Plaza, Suite 825 St. Louis, MO 63146 September 26, 2017 Revised: October 16, 2017

Preliminary results from the High Speed Airframe Integration Research project

NASA Technical Reports Server (NTRS)

Coen, Peter G.; Sobieszczanski-Sobieski, Jaroslaw; Dollyhigh, Samuel M.

1992-01-01

A review is presented of the accomplishment of the near term objectives of developing an analysis system and optimization methods during the first year of the NASA Langley High Speed Airframe Integration Research (HiSAIR) project. The characteristics of a Mach 3 HSCT transport have been analyzed utilizing the newly developed process. In addition to showing more detailed information about the aerodynamic and structural coupling for this type of vehicle, this exercise aided in further refining the data requirements for the analysis process.

Advances in Vehicle Systems Concepts and Integration. (les Avancees en concepts systemes pour vehicules et en integration)

DTIC Science & Technology

2000-04-01

the electronics manufacturers who have made avionics upgrades a profitable line-of- business . However, this observation is not in the best interest of...in encouraging communica- both the AH-lZ and UH-IY airframes, for example). tion between all IPT members. These TIMs were held Technical leaders from...aircraft operating in the maritime and placed strategically on the airframes to increase their environment experienced by the Navy and Marines are

Exhaust plumes and their interaction with missile airframes - A new viewpoint

NASA Technical Reports Server (NTRS)

Dash, S. M.; Sinha, N.

1992-01-01

The present, novel treatment of missile airframe-exhaust plume interactions emphasizes their simulation via a formal solution of the Reynolds-averaged Navier-Stokes (RNS) equation and is accordingly able to address the simulation requirements of novel missiles with nonconventional/integrated propulsion systems. The method is made possible by implicit RNS codes with improved artificial dissipation models, generalized geometric capabilities, and improved two-equation turbulence models, as well as by such codes' recent incorporation of plume thermochemistry and multiphase flow effects.

Encyclopedia of US Air Force Aircraft and Missile Systems. Volume 1. Post-World War II Fighters 1945-1973,

DTIC Science & Technology

1978-01-01

around 100 miles. With two Lockheed external 165-gallon tanks (and a full rocket load ) it was only 225 miles. Lieutenants Edward R. Johnston and...start. 12 While waiting for acceptable engines, North American had to bear the expense of storing unequipped F-82 airframes.13 The situation grew so bad...secure a suitable airframe for the GE TG-180 axial flow gas turbine engine, that the Air Technical Service Command of the Army Air Forces was

Aerodynamic Investigation of C-141 Leading Edge Modifications for Cruise Drag Reduction--Test 2.

DTIC Science & Technology

1981-04-01

82171.6 1 ((1 I III 11 1 - MI( RO( )FY R~ I IN II I (I 041PI AD A099 6 6 2 _ AFWAL-TR-81-3032 AERODYNAMIC INVESTIGATION OF C-141 LEADING EDGE MODIFICATIONS...FOR CRUISE DRAG REDUCTION -- TEST 2 Robert A. Large, Captain, USAF Aerodynamics & Airframe Branch Aeromechanics Division Flight Dynamics Laboratory...KEMloUA Ch, Aerodynamics & Airframe Br Aeromechanics Division FOR THE COMMANDER hie" Aeromechanics Division "If your address has changed, if you wish to

Fuel efficiency through new airframe technology

NASA Technical Reports Server (NTRS)

Leonard, R. W.

1982-01-01

In its Aircraft Energy Efficiency Program, NASA has expended approximately 200 million dollars toward development and application of advanced airframe technologies to United States's commercial transports. United States manufacturers have already been given a significant boost toward early application of advanced composite materials to control surface and empennage structures and toward selected applications of active controls and advanced aerodynamic concepts. In addition, significant progress in definition and development of innovative, but realistic systems for laminar flow control over the wings of future transports has already been made.

Integrated flight/propulsion control system design based on a centralized approach

NASA Technical Reports Server (NTRS)

Garg, Sanjay; Mattern, Duane L.; Bullard, Randy E.

1989-01-01

An integrated flight/propulsion control system design is presented for the piloted longitudinal landing task with a modern, statically unstable, fighter aircraft. A centralized compensator based on the Linear Quadratic Gaussian/Loop Transfer Recovery methodology is first obtained to satisfy the feedback loop performance and robustness specificiations. This high-order centralized compensator is then partitioned into airframe and engine sub-controllers based on modal controllability/observability for the compensator modes. The order of the sub-controllers is then reduced using internally-balanced realization techniques and the sub-controllers are simplified by neglecting the insignificant feedbacks. These sub-controllers have the advantage that they can be implemented as separate controllers on the airframe and the engine while still retaining the important performance and stability characteristics of the full-order centralized compensator. Command prefilters are then designed for the closed-loop system with the simplified sub-controllers to obtain the desired system response to airframe and engine command inputs, and the overall system performance evaluation results are presented.

An Assessment of IMPAC - Integrated Methodology for Propulsion and Airframe Controls

NASA Technical Reports Server (NTRS)

Walker, G. P.; Wagner, E. A.; Bodden, D. S.

1996-01-01

This report documents the work done under a NASA sponsored contract to transition to industry technologies developed under the NASA Lewis Research Center IMPAC (Integrated Methodology for Propulsion and Airframe Control) program. The critical steps in IMPAC are exercised on an example integrated flight/propulsion control design for linear airframe/engine models of a conceptual STOVL (Short Take-Off and Vertical Landing) aircraft, and MATRIXX (TM) executive files to implement each step are developed. The results from the example study are analyzed and lessons learned are listed along with recommendations that will improve the application of each design step. The end product of this research is a set of software requirements for developing a user-friendly control design tool which will automate the steps in the IMPAC methodology. Prototypes for a graphical user interface (GUI) are sketched to specify how the tool will interact with the user, and it is recommended to build the tool around existing computer aided control design software packages.

Hyper-X Flight Engine Ground Testing for X-43 Flight Risk Reduction

NASA Technical Reports Server (NTRS)

Huebner, Lawrence D.; Rock, Kenneth E.; Ruf, Edward G.; Witte, David W.; Andrews, Earl H., Jr.

2001-01-01

Airframe-integrated scramjet engine testing has been completed at Mach 7 flight conditions in the NASA Langley 8-Foot High Temperature Tunnel as part of the NASA Hyper-X program. This test provided engine performance and operability data, as well as design and database verification, for the Mach 7 flight tests of the Hyper-X research vehicle (X-43), which will provide the first-ever airframe-integrated scramjet data in flight. The Hyper-X Flight Engine, a duplicate Mach 7 X-43 scramjet engine, was mounted on an airframe structure that duplicated the entire three-dimensional propulsion flowpath from the vehicle leading edge to the vehicle trailing edge. This model was also tested to verify and validate the complete flight-like engine system. This paper describes the subsystems that were subjected to flight-like conditions and presents supporting data. The results from this test help to reduce risk for the Mach 7 flights of the X-43.

Computational Aeroelastic Modeling of Airframes and TurboMachinery: Progress and Challenges

NASA Technical Reports Server (NTRS)

Bartels, R. E.; Sayma, A. I.

2006-01-01

Computational analyses such as computational fluid dynamics and computational structural dynamics have made major advances toward maturity as engineering tools. Computational aeroelasticity is the integration of these disciplines. As computational aeroelasticity matures it too finds an increasing role in the design and analysis of aerospace vehicles. This paper presents a survey of the current state of computational aeroelasticity with a discussion of recent research, success and continuing challenges in its progressive integration into multidisciplinary aerospace design. This paper approaches computational aeroelasticity from the perspective of the two main areas of application: airframe and turbomachinery design. An overview will be presented of the different prediction methods used for each field of application. Differing levels of nonlinear modeling will be discussed with insight into accuracy versus complexity and computational requirements. Subjects will include current advanced methods (linear and nonlinear), nonlinear flow models, use of order reduction techniques and future trends in incorporating structural nonlinearity. Examples in which computational aeroelasticity is currently being integrated into the design of airframes and turbomachinery will be presented.

Approach to Modeling Boundary Layer Ingestion Using a Fully Coupled Propulsion-RANS Model

NASA Technical Reports Server (NTRS)

Gray, Justin; Mader, Charles A.; Kenway, Gaetan K. W.; Martins, Joaquim R. R. A.

2017-01-01

Although boundary layer ingestion (BLI), or wake ingestion, is commonly applied in marine propulsion applications, it has not yet seen wide-spread adoption in aircraft applications. However, recent studies have predicted that BLI offers a potential for a 10 reduction in aircraft fuel burn, even on a fairly traditional aircraft configuration. This dramatic reduction in fuel burn is achieved via tight integration of the propulsion system and airframe aerodynamics, but actually realizing such large performance gains will require modifying the aircraft design process to account for this integration. Traditionally, in aircraft design, the airframe and the propulsion system are designed separately and then the engine sizing is managed with a rubber-engine approach. This works when the propulsion system is placed in the free-stream air, away from the aerodynamic influence of the airframe, and it is reasonable to assume that small changes to either system won't have a strong impact on the other.

An Investigation of the Impact of Aerodynamic Model Fidelity on Close-In Combat Effectiveness Prediction in Piloted Simulation

NASA Technical Reports Server (NTRS)

Persing, T. Ray; Bellish, Christine A.; Brandon, Jay; Kenney, P. Sean; Carzoo, Susan; Buttrill, Catherine; Guenther, Arlene

2005-01-01

Several aircraft airframe modeling approaches are currently being used in the DoD community for acquisition, threat evaluation, training, and other purposes. To date there has been no clear empirical study of the impact of airframe simulation fidelity on piloted real-time aircraft simulation study results, or when use of a particular level of fidelity is indicated. This paper documents a series of piloted simulation studies using three different levels of airframe model fidelity. This study was conducted using the NASA Langley Differential Maneuvering Simulator. Evaluations were conducted with three pilots for scenarios requiring extensive maneuvering of the airplanes during air combat. In many cases, a low-fidelity modified point-mass model may be sufficient to evaluate the combat effectiveness of the aircraft. However, in cases where high angle-of-attack flying qualities and aerodynamic performance are a factor or when precision tracking ability of the aircraft must be represented, use of high-fidelity models is indicated.

Investigation of the effects of aeroelastic deformations on the radar cross section of aircraft

NASA Astrophysics Data System (ADS)

McKenzie, Samuel D.

1991-12-01

The effects of aeroelastic deformations on the radar cross section (RCS) of a T-38 trainer jet and a C-5A transport aircraft are examined and characterized. Realistic representations of structural wing deformations are obtained from a mechanical/computer aided design software package called NASTRAN. NASTRAN is used to evaluate the structural parameters of the aircraft as well as the restraints and loads associated with realistic flight conditions. Geometries for both the non-deformed and deformed airframes are obtained from the NASTRAN models and translated into RCS models. The RCS is analyzed using a numerical modeling code called the Radar Cross Section - Basic Scattering Code, version 2 which was developed at the Ohio State University and is based on the uniform geometric theory of diffraction. The code is used to analyze the effects of aeroelastic deformations on the RCS of the aircraft by comparing the computed RCS representing the deformed airframe to that of the non-deformed airframe and characterizing the differences between them.

The X-43A (Hyper-X) Flies Into the Record Books

NASA Technical Reports Server (NTRS)

Grindle, Laurie; Bahm, Catherine

2006-01-01

The goal of the Hyper-X research program, conducted jointly by the NASA Dryden Flight Research Center and the NASA Langley Research Center, was to demonstrate and validate the technology, experimental techniques, and computation methods and tools for design and performance predictions of a hypersonic aircraft with an airframe-integrated, scramjet propulsion system. Three X-43A airframe-integrated, scramjet research vehicles were designed and fabricated to achieve that goal by flight test: two test flights at Mach 7 and one test flight at Mach 10. The first flight, conducted on June 2, 2001, experienced a launch vehicle failure and resulted in a 9-month mishap investigation. A two-year return-to-flight effort ensued and concluded when the second Mach 7 flight was successful on March 27, 2004. Just eight months later, on November 16, the X-43A successfully completed the third and final flight. These two flights were the first flight demonstrations, at Mach 7 and Mach 10 respectively, of an airframe-integrated, scramjet-powered, hypersonic vehicle.

Experimental investigation of wing installation effects on a two-dimensional mixer/ejector nozzle for supersonic transport aircraft

NASA Technical Reports Server (NTRS)

Anderson, David J.; Lambert, Heather H.; Mizukami, Masashi

1992-01-01

Experimental results from a wind tunnel test conducted to investigate propulsion/airframe integration (PAI) effects are presented. The objectives of the test were to examine rough order-of-magnitude changes in the acoustic characteristics of a mixer/ejector nozzle due to the presence of a wing and to obtain limited wing and nozzle flow-field measurements. A simple representative supersonic transport wing planform, with deflecting flaps, was installed above a two-dimensional mixer/ejector nozzle that was supplied with high-pressure heated air. Various configurations and wing positions with respect to the nozzle were studied. Because of hardware problems, no acoustics and only a limited set of flow-field data were obtained. For most hardware configurations tested, no significant propulsion/airframe integration effects were identified. Significant effects were seen for extreme flap deflections. The combination of the exploratory nature of the test and the limited flow-field instrumentation made it impossible to identify definitive propulsion/airframe integration effects.

Cooperative control theory and integrated flight and propulsion control

NASA Technical Reports Server (NTRS)

Schmidt, David K.; Schierman, John D.

1994-01-01

This report documents the activities and research results obtained under a grant (NAG3-998) from the NASA Lewis Research Center. The focus of the research was the investigation of dynamic interactions between airframe and engines for advanced ASTOVL aircraft configurations, and the analysis of the implications of these interactions on the stability and performance of the airframe and engine control systems. In addition, the need for integrated flight and propulsion control for such aircraft was addressed. The major contribution of this research was the exposition of the fact that airframe and engine interactions could be present, and their effects could include loss of stability and performance of the control systems. Also, the significance of two directional, as opposed to one-directional, coupling was identified and explained. A multi variable stability and performance analysis methodology was developed, and applied to several candidate aircraft configurations. Also exposed was the fact that with interactions present along with some integrated control approaches, the engine command/limiting logic (which represents an important non-linear component of the engine control system) can impact closed-loop airframe/engine system stability. Finally, a brief investigation of control-law synthesis techniques appropriate for the class of systems was pursued, and it was determined that multi variable techniques, included model-following formulations of LQG and/or H (infinity) methods showed promise. However, for practical reasons, decentralized control architectures are preferred, which is an architecture incompatible with these synthesis methods.

Aerodynamic Design of the Hybrid Wing Body Propulsion-Airframe Integration

NASA Technical Reports Server (NTRS)

Liou, May-Fun; Kim, Hyoungjin; Lee, ByungJoon; Liou, Meng-Sing

2017-01-01

A hybrid wingbody (HWB) concept is being considered by NASA as a potential subsonic transport aircraft that meets aerodynamic, fuel, emission, and noise goals in the time frame of the 2030s. While the concept promises advantages over conventional wing-and-tube aircraft, it poses unknowns and risks, thus requiring in-depth and broad assessments. Specifically, the configuration entails a tight integration of the airframe and propulsion geometries; the aerodynamic impact has to be carefully evaluated. With the propulsion nacelle installed on the (upper) body, the lift and drag are affected by the mutual interference effects between the airframe and nacelle. The static margin for longitudinal stability is also adversely changed. We develop a design approach in which the integrated geometry of airframe (HWB) and propulsion is accounted for simultaneously in a simple algebraic manner, via parameterization of the planform and airfoils at control sections of the wingbody. In this paper, we present the design of a 300-passenger transport that employs distributed electric fans for propulsion. The trim for stability is achieved through the use of the wingtip twist angle. The geometric shape variables are determined through the adjoint optimization method by minimizing the drag while subject to lift, pitch moment, and geometry constraints. The design results clearly show the influence on the aerodynamic characteristics of the installed nacelle and trimming for stability. A drag minimization with the trim constraint yields a reduction of 10 counts in the drag coefficient.

Reliability-Based Design Optimization of a Composite Airframe Component

NASA Technical Reports Server (NTRS)

Pai, Shantaram S.; Coroneos, Rula; Patnaik, Surya N.

2011-01-01

A stochastic optimization methodology (SDO) has been developed to design airframe structural components made of metallic and composite materials. The design method accommodates uncertainties in load, strength, and material properties that are defined by distribution functions with mean values and standard deviations. A response parameter, like a failure mode, has become a function of reliability. The primitive variables like thermomechanical loads, material properties, and failure theories, as well as variables like depth of beam or thickness of a membrane, are considered random parameters with specified distribution functions defined by mean values and standard deviations.

Experimental and analytical investigation of active loads control for aircraft landing gear

NASA Technical Reports Server (NTRS)

Morris, D. L.; Mcgehee, J. R.

1983-01-01

A series hydraulic, active loads control main landing gear from a light, twin-engine civil aircraft was investigated. Tests included landing impact and traversal of simulated runway roughness. It is shown that the active gear is feasible and very effective in reducing the force transmitted to the airframe. Preliminary validation of a multidegree of freedom active gear flexible airframe takeoff and landing analysis computer program, which may be used as a design tool for active gear systems, is accomplished by comparing experimental and computed data for the passive and active gears.

In Search of the Physics: The Interplay of Experiment and Computation in Airframe Noise Research: Flap-Edge Noise

NASA Technical Reports Server (NTRS)

Streett, C. L.; Lockard, D. P.; Singer, B. A.; Khorrami, M. R.; Choudhari, M. M.

2003-01-01

The LaRC investigative process for airframe noise has proven to be a useful guide for elucidation of the physics of flow-induced noise generation over the last five years. This process, relying on a close interplay between experiment and computation, is described and demonstrated here on the archetypal problem of flap-edge noise. Some detailed results from both experiment and computation are shown to illustrate the process, and a description of the multi-source physics seen in this problem is conjectured.

Studies of scramjet/airframe integration techniques for hypersonic aircraft

NASA Technical Reports Server (NTRS)

Edwards, C. L. W.; Small, W. J.; Weidner, J. P.; Johnston, P. J.

1975-01-01

New design and analysis techniques for engine-airframe integration were applied in a recent hypersonic vehicle design study. A new technique was developed to design the vehicle's forebody so that uniform precompressed flow was produced at the inlet entrance. Results are verified with three-dimensional characteristic calculations. Results from a new three-dimensional method for calculating nozzle flows show that the entire lower afterbody of the vehicle can be used as a scramjet exhaust nozzle to achieve efficient, controlled, and stable flight over a wide range of flight conditions.

Semi-empirical airframe noise prediction model

NASA Technical Reports Server (NTRS)

Hersh, A. S.; Putnam, T. W.; Lasagna, P. L.; Burcham, F. W., Jr.

1976-01-01

A semi-empirical maximum overall sound pressure level (OASPL) airframe noise model was derived. The noise radiated from aircraft wings and flaps was modeled by using the trailing-edge diffracted quadrupole sound theory derived by Ffowcs Williams and Hall. The noise radiated from the landing gear was modeled by using the acoustic dipole sound theory derived by Curle. The model was successfully correlated with maximum OASPL flyover noise measurements obtained at the NASA Dryden Flight Research Center for three jet aircraft - the Lockheed JetStar, the Convair 990, and the Boeing 747 aircraft.

Aviation Safety Program Atmospheric Environment Safety Technologies (AEST) Project

NASA Technical Reports Server (NTRS)

Colantonio, Ron

2011-01-01

Engine Icing: Characterization and Simulation Capability: Develop knowledge bases, analysis methods, and simulation tools needed to address the problem of engine icing; in particular, ice-crystal icing Airframe Icing Simulation and Engineering Tool Capability: Develop and demonstrate 3-D capability to simulate and model airframe ice accretion and related aerodynamic performance degradation for current and future aircraft configurations in an expanded icing environment that includes freezing drizzle/rain Atmospheric Hazard Sensing and Mitigation Technology Capability: Improve and expand remote sensing and mitigation of hazardous atmospheric environments and phenomena

Airframe integrity based on Bayesian approach

NASA Astrophysics Data System (ADS)

Hurtado Cahuao, Jose Luis

Aircraft aging has become an immense challenge in terms of ensuring the safety of the fleet while controlling life cycle costs. One of the major concerns in aircraft structures is the development of fatigue cracks in the fastener holes. A probabilistic-based method has been proposed to manage this problem. In this research, the Bayes' theorem is used to assess airframe integrity by updating generic data with airframe inspection data while such data are compiled. This research discusses the methodology developed for assessment of loss of airframe integrity due to fatigue cracking in the fastener holes of an aging platform. The methodology requires a probability density function (pdf) at the end of SAFE life. Subsequently, a crack growth regime begins. As the Bayesian analysis requires information of a prior initial crack size pdf, such a pdf is assumed and verified to be lognormally distributed. The prior distribution of crack size as cracks grow is modeled through a combined Inverse Power Law (IPL) model and lognormal relationships. The first set of inspections is used as the evidence for updating the crack size distribution at the various stages of aircraft life. Moreover, the materials used in the structural part of the aircrafts have variations in their properties due to their calibration errors and machine alignment. A Matlab routine (PCGROW) is developed to calculate the crack distribution growth through three different crack growth models. As the first step, the material properties and the initial crack size are sampled. A standard Monte Carlo simulation is employed for this sampling process. At the corresponding aircraft age, the crack observed during the inspections, is used to update the crack size distribution and proceed in time. After the updating, it is possible to estimate the probability of structural failure as a function of flight hours for a given aircraft in the future. The results show very accurate and useful values related to the reliability and integrity of airframes in aging aircrafts. Inspection data shown in this dissertation are not the actual data from known aircrafts and are only used to demonstrate the methodologies.

Evaluation of composite materials providing improved acoustic transmission loss for UAVs

NASA Astrophysics Data System (ADS)

Callicoat, Jeffrey R.

With the proliferation of Unmanned Aerial Vehicles (UAVs) in civilian airspace in the near future, community noise will be a major issue of concern. Numerous studies have shown a direct link between community noise pollution (i.e., road traffic noise and airport noise) and serious health problems. There exists, therefore, a pressing need to create quiet UAVs, and this drives the need for noise-attenuating materials and structures suitable for UAV airframe fabrication. By shrouding predominant noise sources such as the engine, exhaust, and even the propeller (in the case of a ducted fan) with the airframe structure, the airframe can serve as a noise transmission barrier and substantially reduce UAV noise profiles. The present research effort is an experimental investigation of light-weight fiber-reinforced composite materials to provide high acoustic transmission loss (TL) for use in fabricating UAV airframes. A transmission loss tube acoustic test system was designed, fabricated, and validated, and extensive testing was done on numerous composite layups of interest for UAV fabrication. Composites under study included carbon fiber, fiberglass, and Kevlar fabrics as skin materials along with vinyl foam, Nomex honeycomb, and balsawood as core materials. Results from testing small 3"x3" samples in the TL tube led to the selection of four composite sandwich panels of interest for further study. Larger 36"x36" test samples of these selected layups were then fabricated and tested using a 2-room methodology. Whereas the TL tube yielded results in the stiffness-controlled region of acoustic behavior, the 2-room tests produced results in the mass-controlled region for these materials, enabling relative performance comparisons over both acoustic regimes. Recognizing that a good material for airframe fabrication should possess not only high TL, but also low weight and high stiffness, load-deflection tests were conducted and overall material performance was compared in terms of the parameter [(TL * stiffness) / surface density]. A sandwich panel layup of 5.7 oz carbon fiber skins with a vinyl foam core emerged as the preferable material choice, and a UAV fuselage of this construction was evaluated in the OSU anechoic chamber and shown to substantially reduce sound propagation from enclosed noise sources.

A summary of recent NASA/Army contributions to rotorcraft vibrations and structural dynamics technology

NASA Technical Reports Server (NTRS)

Kvaternik, Raymond G.; Bartlett, Felton D., Jr.; Cline, John H.

1988-01-01

The requirement for low vibrations has achieved the status of a critical design consideration in modern helicopters. There is now a recognized need to account for vibrations during both the analytical and experimental phases of design. Research activities in this area were both broad and varied and notable advances were made in recent years in the critical elements of the technology base needed to achieve the goal of a jet smooth ride. The purpose is to present an overview of accomplishments and current activities of govern and government-sponsored research in the area of rotorcraft vibrations and structural dynamics, focusing on NASA and Army contributions over the last decade or so. Specific topics addressed include: airframe finite-element modeling for static and dynamic analyses, analysis of coupled rotor-airframe vibrations, optimization of airframes subject to vibration constraints, active and passive control of vibrations in both the rotating and fixed systems, and integration of testing and analysis in such guises as modal analysis, system identification, structural modification, and vibratory loads measurement.

Utility of an airframe referenced spatial auditory display for general aviation operations

NASA Astrophysics Data System (ADS)

Naqvi, M. Hassan; Wigdahl, Alan J.; Ranaudo, Richard J.

2009-05-01

The University of Tennessee Space Institute (UTSI) completed flight testing with an airframe-referenced localized audio cueing display. The purpose was to assess its affect on pilot performance, workload, and situational awareness in two scenarios simulating single-pilot general aviation operations under instrument meteorological conditions. Each scenario consisted of 12 test procedures conducted under simulated instrument meteorological conditions, half with the cue off, and half with the cue on. Simulated aircraft malfunctions were strategically inserted at critical times during each test procedure. Ten pilots participated in the study; half flew a moderate workload scenario consisting of point to point navigation and holding pattern operations and half flew a high workload scenario consisting of non precision approaches and missed approach procedures. Flight data consisted of aircraft and navigation state parameters, NASA Task Load Index (TLX) assessments, and post-flight questionnaires. With localized cues there was slightly better pilot technical performance, a reduction in workload, and a perceived improvement in situational awareness. Results indicate that an airframe-referenced auditory display has utility and pilot acceptance in general aviation operations.

The NASA/industry Design Analysis Methods for Vibrations (DAMVIBS) program: Boeing Helicopters airframe finite element modeling

NASA Technical Reports Server (NTRS)

Gabel, R.; Lang, P.; Reed, D.

1993-01-01

Mathematical models based on the finite element method of structural analysis, as embodied in the NASTRAN computer code, are routinely used by the helicopter industry to calculate airframe static internal loads used for sizing structural members. Historically, less reliance has been placed on the vibration predictions based on these models. Beginning in the early 1980's NASA's Langley Research Center initiated an industry wide program with the objective of engendering the needed trust in vibration predictions using these models and establishing a body of modeling guides which would enable confident future prediction of airframe vibration as part of the regular design process. Emphasis in this paper is placed on the successful modeling of the Army/Boeing CH-47D which showed reasonable correlation with test data. A principal finding indicates that improved dynamic analysis requires greater attention to detail and perhaps a finer mesh, especially the mass distribution, than the usual stress model. Post program modeling efforts show improved correlation placing key modal frequencies in the b/rev range with 4 percent of the test frequencies.

Recent advances in integrated multidisciplinary optimization of rotorcraft

NASA Technical Reports Server (NTRS)

Adelman, Howard M.; Walsh, Joanne L.; Pritchard, Jocelyn I.

1992-01-01

A joint activity involving NASA and Army researchers at NASA LaRC to develop optimization procedures to improve the rotor blade design process by integrating appropriate disciplines and accounting for all of the important interactions among the disciplines is described. The disciplines involved include rotor aerodynamics, rotor dynamics, rotor structures, airframe dynamics, and acoustics. The work is focused on combining these five key disciplines in an optimization procedure capable of designing a rotor system to satisfy multidisciplinary design requirements. Fundamental to the plan is a three-phased approach. In phase 1, the disciplines of blade dynamics, blade aerodynamics, and blade structure are closely coupled while acoustics and airframe dynamics are decoupled and are accounted for as effective constraints on the design for the first three disciplines. In phase 2, acoustics is integrated with the first three disciplines. Finally, in phase 3, airframe dynamics is integrated with the other four disciplines. Representative results from work performed to date are described. These include optimal placement of tuning masses for reduction of blade vibratory shear forces, integrated aerodynamic/dynamic optimization, and integrated aerodynamic/dynamic/structural optimization. Examples of validating procedures are described.

Recent advances in multidisciplinary optimization of rotorcraft

NASA Technical Reports Server (NTRS)

Adelman, Howard M.; Walsh, Joanne L.; Pritchard, Jocelyn I.

1992-01-01

A joint activity involving NASA and Army researchers at NASA LaRC to develop optimization procedures to improve the rotor blade design process by integrating appropriate disciplines and accounting for all of the important interactions among the disciplines is described. The disciplines involved include rotor aerodynamics, rotor dynamics, rotor structures, airframe dynamics, and acoustics. The work is focused on combining these five key disciplines in an optimization procedure capable of designing a rotor system to satisfy multidisciplinary design requirements. Fundamental to the plan is a three-phased approach. In phase 1, the disciplines of blade dynamics, blade aerodynamics, and blade structure are closely coupled while acoustics and airframe dynamics are decoupled and are accounted for as effective constraints on the design for the first three disciplines. In phase 2, acoustics is integrated with the first three disciplines. Finally, in phase 3, airframe dynamics is integrated with the other four disciplines. Representative results from work performed to date are described. These include optimal placement of tuning masses for reduction of blade vibratory shear forces, integrated aerodynamic/dynamic optimization, and integrated aerodynamic/dynamic/structural optimization. Examples of validating procedures are described.

A Comparison of Ffowcs Williams-Hawkings Solvers for Airframe Noise Applications

NASA Technical Reports Server (NTRS)

Lockard, David P.

2002-01-01

This paper presents a comparison between two implementations of the Ffowcs Williams and Hawkings equation for airframe noise applications. Airframe systems are generally moving at constant speed and not rotating, so these conditions are used in the current investigation. Efficient and easily implemented forms of the equations applicable to subsonic, rectilinear motion of all acoustic sources are used. The assumptions allow the derivation of a simple form of the equations in the frequency-domain, and the time-domain method uses the restrictions on the motion to reduce the work required to find the emission time. The comparison between the frequency domain method and the retarded time formulation reveals some of the advantages of the different approaches. Both methods are still capable of predicting the far-field noise from nonlinear near-field flow quantities. Because of the large input data sets and potentially large numbers of observer positions of interest in three-dimensional problems, both codes utilize the message passing interface to divide the problem among different processors. Example problems are used to demonstrate the usefulness and efficiency of the two schemes.

The Prediction of Scattered Broadband Shock-Associated Noise

NASA Technical Reports Server (NTRS)

Miller, Steven A. E.

2015-01-01

A mathematical model is developed for the prediction of scattered broadband shock-associated noise. Model arguments are dependent on the vector Green's function of the linearized Euler equations, steady Reynolds-averaged Navier-Stokes solutions, and the two-point cross-correlation of the equivalent source. The equivalent source is dependent on steady Reynolds-averaged Navier-Stokes solutions of the jet flow, that capture the nozzle geometry and airframe surface. Contours of the time-averaged streamwise velocity component and turbulent kinetic energy are examined with varying airframe position relative to the nozzle exit. Propagation effects are incorporated by approximating the vector Green's function of the linearized Euler equations. This approximation involves the use of ray theory and an assumption that broadband shock-associated noise is relatively unaffected by the refraction of the jet shear layer. A non-dimensional parameter is proposed that quantifies the changes of the broadband shock-associated noise source with varying jet operating condition and airframe position. Scattered broadband shock-associated noise possesses a second set of broadband lobes that are due to the effect of scattering. Presented predictions demonstrate relatively good agreement compared to a wide variety of measurements.

Computer prediction of three-dimensional potential flow fields in which aircraft propellers operate. M.S. Thesis

NASA Technical Reports Server (NTRS)

Jumper, S. J.

1982-01-01

A computer program was developed to calculate the three dimensional, steady, incompressible, inviscid, irrotational flow field at the propeller plane (propeller removed) located upstream of an arbitrary airframe geometry. The program uses a horseshoe vortex of known strength to model the wing. All other airframe surfaces are modeled by a network source panels of unknown strength which is exposed to a uniform free stream and the wing-induced velocity field. By satisfying boundary conditions on each panel (the Neumann problem), relaxed boundary conditions being used on certain panels to simulate inlet inflow, the source strengths are determined. From the known source and wing vortex strengths, the resulting velocity fields on the airframe surface and at the propeller plane are obtained. All program equations are derived in detail, and a brief description of the program structure is presented. A user's manual which fully documents the program is cited. Computer predictions of the flow on the surface of a sphere and at a propeller plane upstream of the sphere are compared with the exact mathematical solutions. Agreement is good, and correct program operation is verified.

Low-Cost Composite Materials and Structures for Aircraft Applications

NASA Technical Reports Server (NTRS)

Deo, Ravi B.; Starnes, James H., Jr.; Holzwarth, Richard C.

2003-01-01

A survey of current applications of composite materials and structures in military, transport and General Aviation aircraft is presented to assess the maturity of composites technology, and the payoffs realized. The results of the survey show that performance requirements and the potential to reduce life cycle costs for military aircraft and direct operating costs for transport aircraft are the main reasons for the selection of composite materials for current aircraft applications. Initial acquisition costs of composite airframe components are affected by high material costs and complex certification tests which appear to discourage the widespread use of composite materials for aircraft applications. Material suppliers have performed very well to date in developing resin matrix and fiber systems for improved mechanical, durability and damage tolerance performance. The next challenge for material suppliers is to reduce material costs and to develop materials that are suitable for simplified and inexpensive manufacturing processes. The focus of airframe manufacturers should be on the development of structural designs that reduce assembly costs by the use of large-scale integration of airframe components with unitized structures and manufacturing processes that minimize excessive manual labor.

Study to investigate design, fabrication and test of low cost concepts for large hybrid composite helicopter fuselage, phase 1

NASA Technical Reports Server (NTRS)

Adams, K. M.; Lucas, J. J.

1975-01-01

The development of a frame/stringer/skin fabrication technique for composite airframe construction was studied as a low cost approach to the manufacture of large helicopter airframe components. A center cabin aluminum airframe section of the Sikorsky CH-53D helicopter was selected for evaluation as a composite structure. The design, as developed, is composed of a woven KEVLAR-49/epoxy skin and graphite/epoxy frames and stringers. To support the selection of this specific design concept a materials study was conducted to develop and select a cure compatible graphite and KEVLAR-49/epoxy resin system, and a foam system capable of maintaining shape and integrity under the processing conditions established. The materials selected were, Narmco 5209/Thornel T-300 graphite, Narmco 5209/KEVLAR-49 woven fabric, and Stathane 8747 polyurethane foam. Eight specimens were fabricated, representative of the frame, stringer, and splice joint attachments. Evaluation of the results of analysis and test indicate that design predictions are good to excellent except for some conservatism of the complex frame splice.

Hypersonic technology-approach to an expanded program

NASA Technical Reports Server (NTRS)

Hearth, D. P.; Preyss, A. E.

1976-01-01

An overview of research, testing, and technology in the hypersonic range. Military and civilian hypersonic flight systems envisaged, ground testing facilities under development, methods for cooling the heated airframe, and use of hydrogen as fuel and coolant are discussed extensively. Air-breathing hypersonic cruise systems are emphasized, the airframe-integrated scramjet configuration is discussed and illustrated, materials proposed for hypersonic vehicles are reviewed, and test results on hypersonic flight (X-15 research aircraft) are indicated. Major advances and major problems in hypersonic flight and hypersonic technology are outlined, and the need for a hypersonic flying-laboratory research craft is stressed.

Lattice Boltzmann for Airframe Noise Predictions

NASA Technical Reports Server (NTRS)

Barad, Michael; Kocheemoolayil, Joseph; Kiris, Cetin

2017-01-01

Increase predictive use of High-Fidelity Computational Aero- Acoustics (CAA) capabilities for NASA's next generation aviation concepts. CFD has been utilized substantially in analysis and design for steady-state problems (RANS). Computational resources are extremely challenged for high-fidelity unsteady problems (e.g. unsteady loads, buffet boundary, jet and installation noise, fan noise, active flow control, airframe noise, etc) ü Need novel techniques for reducing the computational resources consumed by current high-fidelity CAA Need routine acoustic analysis of aircraft components at full-scale Reynolds number from first principles Need an order of magnitude reduction in wall time to solution!

Aerodynamic Engine/Airframe Integration for High Performance Aircraft and Missiles (L’Integration Aerodynamique des Moteurs et des Cellules dans les Avions et les Missiles a Hautes Performances)

DTIC Science & Technology

1992-09-01

qui a POUr object d~cvaluer la pertinence du symposium ci Ia mesure dans laquelle il a repondu aux attentes de Ia communautti atirospatiale. a ýtit...testing have progressed steadily in the last 30 years. the context of military and civil engine/airframe integration This paper will focus attention on...events of the early 90s close to our collective and military designs require increased attention to be paid to consciousness, it is clear that a

Innovative Materials for Aircraft Morphing

NASA Technical Reports Server (NTRS)

Simpson, J. O.; Wise, S. A.; Bryant, R. G.; Cano, R. J.; Gates, T. S.; Hinkley, J. A.; Rogowski, R. S.; Whitley, K. S.

1997-01-01

Reported herein is an overview of the research being conducted within the Materials Division at NASA Langley Research Center on the development of smart material technologies for advanced airframe systems. The research is a part of the Aircraft Morphing Program which is a new six-year research program to develop smart components for self-adaptive airframe systems. The fundamental areas of materials research within the program are computational materials; advanced piezoelectric materials; advanced fiber optic sensing techniques; and fabrication of integrated composite structures. This paper presents a portion of the ongoing research in each of these areas of materials research.

V/STOL tilt rotor aircraft study. Volume 10: Performance and stability test of A 1-14.622 Froude scaled Boeing Vertol Model 222 tilt rotor aircraft (Phase 1)

NASA Technical Reports Server (NTRS)

Mchugh, F. J.; Eason, W.; Alexander, H. R.; Mutter, H.

1973-01-01

Wind tunnel test data obtained from a 1/4.622 Froude scale Boeing Model 222 with a full span, two prop, tilt rotor, powered model in the Boeing V/STOL wind tunnel are reported. Data were taken in transition and cruise flight conditions and include performance, stability and control and blade loads information. The effects of the rotors, tail surfaces and airframe on the performance and stability are isolated as are the effects of the airframe on the rotors.

Aeroacoustic Research Techniques: Jets to Autos

NASA Technical Reports Server (NTRS)

Soderman, Paul T.

1999-01-01

Aeroacoustic research has benefited from the development of advanced techniques for the study of fluid mechanically generated noise New instrumentation; methodologies, information technologies, and facilities have evolved to help researchers investigate the complexities of aircraft and automobile noise. In this paper, research techniques are reviewed with emphasis on the subject closest to the author s experience: aircraft propulsion and airframe noise in simulated flight. A new technology developed for the study of aircraft airframe noise is described as a potential tool for the study of automobile noise. The important role of information technology in aeroacoustic research is discussed.

British government, industry agree to fund Hotel launcher studies

NASA Astrophysics Data System (ADS)

Brown, D. A.

1986-02-01

A program status assessment is presented for the horizontal takeoff and landing 'Hotol' single-stage-to-orbit space launcher, for which parallel, two-year airframe and propulsion system proof-of-concept studies have been approved. A two-year initial development program for the airframe would be followed by a four-year development and manufacturing phase that would begin upon the propulsion system concept's successful demonstration. Flight trials could begin in 1996. A number of significant modifications have already been made to the initial design concept, such as to the foreplanes, afterbody, engine intake, and orbital control system.

Nondestructive Evaluation (NDE) Results on Sikorsky Aircraft Survivable Affordable Reparable Airframe Program (SARAP) Samples

NASA Technical Reports Server (NTRS)

Zalameda, Joseph N.; Anastasi, Robert F.; Madaras, Eric I.

2004-01-01

The Survivable, Affordable, Reparable Airframe Program (SARAP) will develop/produce new structural design concepts with lower structural weight, reduced manufacturing complexity and development time, increased readiness, and improved threat protection. These new structural concepts will require advanced field capable inspection technologies to help meet the SARAP structural objectives. In the area of repair, damage assessment using nondestructive inspection (NDI) is critical to identify repair location and size. The purpose of this work is to conduct an assessment of new and emerging NDI methods that can potentially satisfy the SARAP program goals.

Characterization of Flap Edge Noise Radiation from a High-Fidelity Airframe Model

NASA Technical Reports Server (NTRS)

Humphreys, William M., Jr.; Khorrami, Mehdi R.; Lockard, David P.; Neuhart, Dan H.; Bahr, Christopher J.

2015-01-01

The results of an experimental study of the noise generated by a baseline high-fidelity airframe model are presented. The test campaign was conducted in the open-jet test section of the NASA Langley 14- by 22-foot Subsonic Tunnel on an 18%-scale, semi-span Gulfstream airframe model incorporating a trailing edge flap and main landing gear. Unsteady surface pressure measurements were obtained from a series of sensors positioned along the two flap edges, and far field acoustic measurements were obtained using a 97-microphone phased array that viewed the pressure side of the airframe. The DAMAS array deconvolution method was employed to determine the locations and strengths of relevant noise sources in the vicinity of the flap edges and the landing gear. A Coherent Output Power (COP) spectral method was used to couple the unsteady surface pressures measured along the flap edges with the phased array output. The results indicate that outboard flap edge noise is dominated by the flap bulb seal cavity with very strong COP coherence over an approximate model-scale frequency range of 1 to 5 kHz observed between the array output and those unsteady pressure sensors nearest the aft end of the cavity. An examination of experimental COP spectra for the inboard flap proved inconclusive, most likely due to a combination of coherence loss caused by decorrelation of acoustic waves propagating through the thick wind tunnel shear layer and contamination of the spectra by tunnel background noise at lower frequencies. Directivity measurements obtained from integration of DAMAS pressure-squared values over defined geometric zones around the model show that the baseline flap and landing gear are only moderately directional as a function of polar emission angle.

Design Oriented Structural Modeling for Airplane Conceptual Design Optimization

NASA Technical Reports Server (NTRS)

Livne, Eli

1999-01-01

The main goal for research conducted with the support of this grant was to develop design oriented structural optimization methods for the conceptual design of airplanes. Traditionally in conceptual design airframe weight is estimated based on statistical equations developed over years of fitting airplane weight data in data bases of similar existing air- planes. Utilization of such regression equations for the design of new airplanes can be justified only if the new air-planes use structural technology similar to the technology on the airplanes in those weight data bases. If any new structural technology is to be pursued or any new unconventional configurations designed the statistical weight equations cannot be used. In such cases any structural weight estimation must be based on rigorous "physics based" structural analysis and optimization of the airframes under consideration. Work under this grant progressed to explore airframe design-oriented structural optimization techniques along two lines of research: methods based on "fast" design oriented finite element technology and methods based on equivalent plate / equivalent shell models of airframes, in which the vehicle is modelled as an assembly of plate and shell components, each simulating a lifting surface or nacelle / fuselage pieces. Since response to changes in geometry are essential in conceptual design of airplanes, as well as the capability to optimize the shape itself, research supported by this grant sought to develop efficient techniques for parametrization of airplane shape and sensitivity analysis with respect to shape design variables. Towards the end of the grant period a prototype automated structural analysis code designed to work with the NASA Aircraft Synthesis conceptual design code ACS= was delivered to NASA Ames.

Microstructural and Mechanical Property Characterization of Shear Formed Aerospace Aluminum Alloys

NASA Technical Reports Server (NTRS)

Troeger, Lillianne P.; Domack, Marcia S.; Wagner, John A.

2000-01-01

Advanced manufacturing processes such as near-net-shape forming can reduce production costs and increase the reliability of launch vehicle and airframe structural components through the reduction of material scrap and part count and the minimization of joints. The current research is an investigation of the processing-microstructure-property relationships for shear formed cylinders of the Al-Cu-Li-Mg-Ag alloy 2195 for space applications and the Al-Cu-Mg-Ag alloy C415 for airframe applications. Cylinders which had undergone various amounts of shear-forming strain were studied to correlate the grain structure, texture, and mechanical properties developed during and after shear forming.

Flight and wind-tunnel comparisons of the inlet-airframe interaction of the F-15 airplane

NASA Technical Reports Server (NTRS)

Webb, L. D.; Andriyich-Varda, D.; Whitmore, S. A.

1984-01-01

The design of inlets and nozzles and their interactions with the airplane which may account for a large percentage of the total drag of modern high performance aircraft is discussed. The inlet/airframe interactions program and the flight tests conducted is described. Inlet drag and lift data from a 7.5% wind-tunnel model are compared with data from an F-15 airplane with instrumentation to match the model. Pressure coefficient variations with variable cowl angles, capture ratios, examples of flow interactions and angles of attack are for Mach numbers of 0.6, 0.9, 1.2, and 1.5 are presented.

Coupled rotor/airframe vibration analysis program manual manual. Volume 1: User's and programmer's instructions

NASA Technical Reports Server (NTRS)

Cassarino, S.; Sopher, R.

1982-01-01

user instruction and software descriptions for the base program of the coupled rotor/airframe vibration analysis are provided. The functional capabilities and procedures for running the program are provided. Interfaces with external programs are discussed. The procedure of synthesizing a dynamic system and the various solution methods are described. Input data and output results are presented. Detailed information is provided on the program structure. Sample test case results for five representative dynamic configurations are provided and discussed. System response are plotted to demonstrate the plots capabilities available. Instructions to install and execute SIMVIB on the CDC computer system are provided.

Validation of an Integrated Airframe and Turbofan Engine Simulation for Evaluation of Propulsion Control Modes

NASA Technical Reports Server (NTRS)

Litt, Jonathan S.; Sowers, T Shane; Liu, Yuan; Owen, A. Karl; Guo, Ten-Huei

2015-01-01

The National Aeronautics and Space Administration (NASA) has developed independent airframe and engine models that have been integrated into a single real-time aircraft simulation for piloted evaluation of propulsion control algorithms. In order to have confidence in the results of these evaluations, the integrated simulation must be validated to demonstrate that its behavior is realistic and that it meets the appropriate Federal Aviation Administration (FAA) certification requirements for aircraft. The paper describes the test procedures and results, demonstrating that the integrated simulation generally meets the FAA requirements and is thus a valid testbed for evaluation of propulsion control modes.

Summary of directional divergence characteristics of several high performance aircraft configurations

NASA Technical Reports Server (NTRS)

Greer, H. D.

1972-01-01

The present paper summarizes the high-angle-of-attack characteristics of a number of high-performance aircraft as determined from model force tests and free-flight model tests and correlates these characteristics with the dynamic directional-stability parameter. This correlation shows that the dynamic directional-stability parameter correlates fairly well with directional divergence. Data are also presented to show the effect of some airframe modifications on the directional divergence potential of the configuration. These results show that leading-edge slates seem to be the most effective airframe modification for reducing or eliminating the directional divergence potential of aircraft with moderately swept wings.

Bifilar analysis users manual, volume 2

NASA Technical Reports Server (NTRS)

Cassarino, S. J.

1980-01-01

The digital computer program developed to study the vibration response of a coupled rotor/bifilar/airframe coupled system is described. The theoretical development of the rotor/airframe system equations of motion is provided. The fuselage and bifilar absorber equations of motion are discussed. The modular block approach used in the make-up of this computer program is described. The input data needed to run the rotor and bifilar absorber analyses is described. Sample output formats are presented and discussed. The results for four test cases, which use the major logic paths of the computer program, are presented. The overall program structure is discussed in detail. The FORTRAN subroutines are described in detail.

Conceptual design study of improved 1985 remote lift-fan V/STOL commercial transports

NASA Technical Reports Server (NTRS)

Cavage, R. L.

1975-01-01

A design study was conducted for a remote lift-fan commercial V/STOL transport for the 1985 time period. The investigation centered on the commercial short haul transportation application to carry 100 passengers over trip distances of 400 nautical miles from a vertical takeoff and landing, and 800 nautical miles after a 1600 foot STOL takeoff. The study included investigation of alternate numbers and arrangements of lift fans and gas generators, fan control margins, and structural concepts. The sensitivity of direct operating costs to major airframe parameters, airframe costs, propulsion costs, yearly aircraft utilization rate, and trip distances are evaluated.

Calculation of flight vibration levels of the AH-1G helicopter and correlation with existing flight vibration measurements

NASA Technical Reports Server (NTRS)

Sopher, R.; Twomey, W. J.

1990-01-01

NASA-Langley is sponsoring a rotorcraft structural dynamics program with the objective to establish in the U.S. a superior capability to utilize finite element analysis models for calculations to support industrial design of helicopter airframe structures. In the initial phase of the program, teams from the major U.S. manufacturers of helicopter airframes will apply extant finite element analysis methods to calculate loads and vibrations of helicopter airframes, and perform correlations between analysis and measurements. The aforementioned rotorcraft structural dynamics program was given the acronym DAMVIBS (Design Analysis Method for Vibrations). Sikorsky's RDYNE Rotorcraft Dynamics Analysis used for the correlation study, the specifics of the application of RDYNE to the AH-1G, and comparisons of the predictions of the method with flight data for loads and vibrations on the AH-1G are described. RDYNE was able to predict trends of variations of loads and vibrations with airspeed, but in some instances magnitudes differed from measured results by factors of two or three to one. Sensitivities were studied of predictions to rotor inflow modeling, effects of torsional modes, number of blade bending modes, fuselage structural damping, and hub modal content.

General approach and scope. [rotor blade design optimization

NASA Technical Reports Server (NTRS)

Adelman, Howard M.; Mantay, Wayne R.

1989-01-01

This paper describes a joint activity involving NASA and Army researchers at the NASA Langley Research Center to develop optimization procedures aimed at improving the rotor blade design process by integrating appropriate disciplines and accounting for all of the important interactions among the disciplines. The disciplines involved include rotor aerodynamics, rotor dynamics, rotor structures, airframe dynamics, and acoustics. The work is focused on combining these five key disciplines in an optimization procedure capable of designing a rotor system to satisfy multidisciplinary design requirements. Fundamental to the plan is a three-phased approach. In phase 1, the disciplines of blade dynamics, blade aerodynamics, and blade structure will be closely coupled, while acoustics and airframe dynamics will be decoupled and be accounted for as effective constraints on the design for the first three disciplines. In phase 2, acoustics is to be integrated with the first three disciplines. Finally, in phase 3, airframe dynamics will be fully integrated with the other four disciplines. This paper deals with details of the phase 1 approach and includes details of the optimization formulation, design variables, constraints, and objective function, as well as details of discipline interactions, analysis methods, and methods for validating the procedure.

Analyzing Aeroelastic Stability of a Tilt-Rotor Aircraft

NASA Technical Reports Server (NTRS)

Kvaternil, Raymond G.

2006-01-01

Proprotor Aeroelastic Stability Analysis, now at version 4.5 (PASTA 4.5), is a FORTRAN computer program for analyzing the aeroelastic stability of a tiltrotor aircraft in the airplane mode of flight. The program employs a 10-degree- of-freedom (DOF), discrete-coordinate, linear mathematical model of a rotor with three or more blades and its drive system coupled to a 10-DOF modal model of an airframe. The user can select which DOFs are included in the analysis. Quasi-steady strip-theory aerodynamics is employed for the aerodynamic loads on the blades, a quasi-steady representation is employed for the aerodynamic loads acting on the vibrational modes of the airframe, and a stability-derivative approach is used for the aerodynamics associated with the rigid-body DOFs of the airframe. Blade parameters that vary with the blade collective pitch can be obtained by interpolation from a user-defined table. Stability is determined by examining the eigenvalues that are obtained by solving the coupled equations of motions as a matrix eigenvalue problem. Notwithstanding the relative simplicity of its mathematical foundation, PASTA 4.5 and its predecessors have played key roles in a number of engineering investigations over the years.

The Effects of Surfaces on the Aerodynamics and Acoustics of Jet Flows

NASA Technical Reports Server (NTRS)

Smith, Matthew J.; Miller, Steven A. E.

2013-01-01

Aircraft noise mitigation is an ongoing challenge for the aeronautics research community. In response to this challenge, low-noise aircraft concepts have been developed that exhibit situations where the jet exhaust interacts with an airframe surface. Jet flows interacting with nearby surfaces manifest a complex behavior in which acoustic and aerodynamic characteristics are altered. In this paper, the variation of the aerodynamics, acoustic source, and far-field acoustic intensity are examined as a large at plate is positioned relative to the nozzle exit. Steady Reynolds-Averaged Navier-Stokes solutions are examined to study the aerodynamic changes in the field-variables and turbulence statistics. The mixing noise model of Tam and Auriault is used to predict the noise produced by the jet. To validate both the aerodynamic and the noise prediction models, results are compared with Particle Image Velocimetry (PIV) and free-field acoustic data respectively. The variation of the aerodynamic quantities and noise source are examined by comparing predictions from various jet and at plate configurations with an isolated jet. To quantify the propulsion airframe aeroacoustic installation effects on the aerodynamic noise source, a non-dimensional number is formed that contains the flow-conditions and airframe installation parameters.

Actuator and aerodynamic modeling for high-angle-of-attack aeroservoelasticity

NASA Technical Reports Server (NTRS)

Brenner, Martin J.

1993-01-01

Accurate prediction of airframe/actuation coupling is required by the imposing demands of modern flight control systems. In particular, for agility enhancement at high angle of attack and low dynamic pressure, structural integration characteristics such as hinge moments, effective actuator stiffness, and airframe/control surface damping can have a significant effect on stability predictions. Actuator responses are customarily represented with low-order transfer functions matched to actuator test data, and control surface stiffness is often modeled as a linear spring. The inclusion of the physical properties of actuation and its installation on the airframe is therefore addressed in this paper using detailed actuator models which consider the physical, electrical, and mechanical elements of actuation. The aeroservoelastic analysis procedure is described in which the actuators are modeled as detailed high-order transfer functions and as approximate low-order transfer functions. The impacts of unsteady aerodynamic modeling on aeroservoelastic stability are also investigated in this paper by varying the order of approximation, or number of aerodynamic lag states, in the analysis. Test data from a thrust-vectoring configuration of an F/A-18 aircraft are compared to predictions to determine the effects on accuracy as a function of modeling complexity.

Actuator and aerodynamic modeling for high-angle-of-attack aeroservoelasticity

NASA Technical Reports Server (NTRS)

Brenner, Martin J.

1993-01-01

Accurate prediction of airframe/actuation coupling is required by the imposing demands of modern flight control systems. In particular, for agility enhancement at high angle of attack and low dynamic pressure, structural integration characteristics such as hinge moments, effective actuator stiffness, and airframe/control surface damping can have a significant effect on stability predictions. Actuator responses are customarily represented with low-order transfer functions matched to actuator test data, and control surface stiffness is often modeled as a linear spring. The inclusion of the physical properties of actuation and its installation on the airframe is therefore addressed using detailed actuator models which consider the physical, electrical, and mechanical elements of actuation. The aeroservoelastic analysis procedure is described in which the actuators are modeled as detailed high-order transfer functions and as approximate low-order transfer functions. The impacts of unsteady aerodynamic modeling on aeroservoelastic stability are also investigated by varying the order of approximation, or number of aerodynamic lag states, in the analysis. Test data from a thrust-vectoring configuration of an F/A-l8 aircraft are compared to predictions to determine the effects on accuracy as a function of modeling complexity.

The Prediction and Analysis of Jet Flows and Scattered Turbulent Mixing Noise about Flight Vehicle Airframes

NASA Technical Reports Server (NTRS)

Miller, Steven A. E.

2014-01-01

Jet flows interacting with nearby surfaces exhibit a complex behavior in which acoustic and aerodynamic characteristics are altered. The physical understanding and prediction of these characteristics are essential to designing future low noise aircraft. A new approach is created for predicting scattered jet mixing noise that utilizes an acoustic analogy and steady Reynolds-averaged Navier-Stokes solutions. A tailored Green's function accounts for the propagation of mixing noise about the airframe and is calculated numerically using a newly developed ray tracing method. The steady aerodynamic statistics, associated unsteady sound source, and acoustic intensity are examined as jet conditions are varied about a large flat plate. A non-dimensional number is proposed to estimate the effect of the aerodynamic noise source relative to jet operating condition and airframe position.The steady Reynolds-averaged Navier-Stokes solutions, acoustic analogy, tailored Green's function, non-dimensional number, and predicted noise are validated with a wide variety of measurements. The combination of the developed theory, ray tracing method, and careful implementation in a stand-alone computer program result in an approach that is more first principles oriented than alternatives, computationally efficient, and captures the relevant physics of fluid-structure interaction.

The Prediction and Analysis of Jet Flows and Scattered Turbulent Mixing Noise About Flight Vehicle Airframes

NASA Technical Reports Server (NTRS)

Miller, Steven A.

2014-01-01

Jet flows interacting with nearby surfaces exhibit a complex behavior in which acoustic and aerodynamic characteristics are altered. The physical understanding and prediction of these characteristics are essential to designing future low noise aircraft. A new approach is created for predicting scattered jet mixing noise that utilizes an acoustic analogy and steady Reynolds-averaged Navier-Stokes solutions. A tailored Green's function accounts for the propagation of mixing noise about the air-frame and is calculated numerically using a newly developed ray tracing method. The steady aerodynamic statistics, associated unsteady sound source, and acoustic intensity are examined as jet conditions are varied about a large at plate. A non-dimensional number is proposed to estimate the effect of the aerodynamic noise source relative to jet operating condition and airframe position. The steady Reynolds-averaged Navier-Stokes solutions, acoustic analogy, tailored Green's function, non- dimensional number, and predicted noise are validated with a wide variety of measurements. The combination of the developed theory, ray tracing method, and careful implementation in a stand-alone computer program result in an approach that is more first principles oriented than alternatives, computationally efficient, and captures the relevant physics of fluid-structure interaction.

Propulsion Airframe Aeroacoustics Technology Evaluation and Selection Using a Multi-Attribute Decision Making Process and Non-Deterministic Design

NASA Technical Reports Server (NTRS)

Burg, Cecile M.; Hill, Geoffrey A.; Brown, Sherilyn A.; Geiselhart, Karl A.

2004-01-01

The Systems Analysis Branch at NASA Langley Research Center has investigated revolutionary Propulsion Airframe Aeroacoustics (PAA) technologies and configurations for a Blended-Wing-Body (BWB) type aircraft as part of its research for NASA s Quiet Aircraft Technology (QAT) Project. Within the context of the long-term NASA goal of reducing the perceived aircraft noise level by a factor of 4 relative to 1997 state of the art, major configuration changes in the propulsion airframe integration system were explored with noise as a primary design consideration. An initial down-select and assessment of candidate PAA technologies for the BWB was performed using a Multi-Attribute Decision Making (MADM) process consisting of organized brainstorming and decision-making tools. The assessments focused on what effect the PAA technologies had on both the overall noise level of the BWB and what effect they had on other major design considerations such as weight, performance and cost. A probabilistic systems analysis of the PAA configurations that presented the best noise reductions with the least negative impact on the system was then performed. Detailed results from the MADM study and the probabilistic systems analysis will be published in the near future.

Experimental Photogrammetric Techniques Used on Five Full-Scale Aircraft Crash Tests

NASA Technical Reports Server (NTRS)

Littell, Justin D.

2016-01-01

Between 2013 and 2015, full-scale crash tests were conducted on five aircraft at the Landing and Impact Research Facility (LandIR) at NASA Langley Research Center (LaRC). Two tests were conducted on CH-46E airframes as part of the Transport Rotorcraft Airframe Crash Testbed (TRACT) project, and three tests were conduced on Cessna 172 aircraft as part of the Emergency Locator Transmitter Survivability and Reliability (ELTSAR) project. Each test served to evaluate a variety of crashworthy systems including: seats, occupants, restraints, composite energy absorbing structures, and Emergency Locator Transmitters. As part of each test, the aircraft were outfitted with a variety of internal and external cameras that were focused on unique aspects of the crash event. A subset of three camera was solely used in the acquisition of photogrammetric test data. Examples of this data range from simple two-dimensional marker tracking for the determination of aircraft impact conditions to entire full-scale airframe deformation to markerless tracking of Anthropomorphic Test Devices (ATDs, a.k.a. crash test dummies) during the crash event. This report describes and discusses the techniques used and implications resulting from the photogrammetric data acquired from each of the five tests.

Bibliography on aerodynamics of airframe/engine integration of high-speed turbine-powered aircraft, volume 1

NASA Technical Reports Server (NTRS)

Nichols, M. R.

1980-01-01

This bibliography was developed as a first step in the preparation of a monograph on the subject of the aerodynamics of airframe/engine integration of high speed turbine powered aircraft. It lists 1535 unclassified documents published mainly in the period from 1955 to 1980. Primary emphasis was devoted to aerodynamic problems and interferences encountered in the integration process; however, extensive coverage also was given to the characteristics and problems of the isolated propulsion system elements. A detailed topic breakdown structure is used. The primary contents of the individual documents are indicated by the combination of the document's title and its location within the framework of the bibliography.

Evaluation of Sc-Bearing Aluminum Alloy C557 for Aerospace Applications

NASA Technical Reports Server (NTRS)

Domack, Marcia S.; Dicus, Dennis L.

2002-01-01

The performance of the Al-Mg-Sc alloy C557 was evaluated to assess its potential for a broad range of aerospace applications, including airframe and launch vehicle structures. Of specific interest were mechanical properties at anticipated service temperatures and thermal stability of the alloy. Performance was compared with conventional airframe aluminum alloys and with other emerging aluminum alloys developed for specific service environments. Mechanical properties and metallurgical structure were evaluated for commercially rolled sheet in the as-received H116 condition and after thermal exposures at 107 C. Metallurgical analyses were performed to de.ne grain morphology and texture, strengthening precipitates, and to assess the effect of thermal exposure.

Correlation of finite-element structural dynamic analysis with measured free vibration characteristics for a full-scale helicopter fuselage

NASA Technical Reports Server (NTRS)

Kenigsberg, I. J.; Dean, M. W.; Malatino, R.

1974-01-01

The correlation achieved with each program provides the material for a discussion of modeling techniques developed for general application to finite-element dynamic analyses of helicopter airframes. Included are the selection of static and dynamic degrees of freedom, cockpit structural modeling, and the extent of flexible-frame modeling in the transmission support region and in the vicinity of large cut-outs. The sensitivity of predicted results to these modeling assumptions are discussed. Both the Sikorsky Finite-Element Airframe Vibration analysis Program (FRAN/Vibration Analysis) and the NASA Structural Analysis Program (NASTRAN) have been correlated with data taken in full-scale vibration tests of a modified CH-53A helicopter.

Performance of PTFE-lined composite journal bearings

NASA Technical Reports Server (NTRS)

Sliney, H. E.; Williams, F. J.

1982-01-01

Plain cylindrical journal bearings consisting of aramid fiber reinforced epoxy outer shells and glass fiber reinforced PTFE lubricating liners were evaluated. All materials in these bearings are electrically nonconductive; thus eliminating the problem of galvanic corrosion sometimes encountered with metal bearings installed in dissimilar metal mountings. Friction and wear characteristics were determined for loads, temperatures, and oscillating conditions that are typical of current airframe bearing applications. Friction and wear characteristics were found to be compatible with most airframe bearing requirements from -23 C to 121 C. Contamination with MIL H-5606 hydraulic fluid increased wear of the PTFE liners at 121 C, but did not affect the structural integrity of the aramid/epoxy composite.

Crashworthy airframe design concepts: Fabrication and testing

NASA Technical Reports Server (NTRS)

Cronkhite, J. D.; Berry, V. L.

1982-01-01

Crashworthy floor concepts applicable to general aviation aircraft metal airframe structures were investigated. Initially several energy absorbing lower fuselage structure concepts were evaluated. Full scale floor sections representative of a twin engine, general aviation airplane lower fuselage structure were designed and fabricated. The floors featured an upper high strength platform with an energy absorbing, crushable structure underneath. Eighteen floors were fabricated that incorporated five different crushable subfloor concepts. The floors were then evaluated through static and dynamic testing. Computer programs NASTRAN and KRASH were used for the static and dynamic analysis of the floor section designs. Two twin engine airplane fuselages were modified to incorporate the most promising crashworthy floor sections for test evaluation.

Thermal-structural design study of an airframe-integrated Scramjet

NASA Technical Reports Server (NTRS)

Killackey, J. J.; Katinsky, E. A.; Tepper, S.; Vuigner, A. A.

1978-01-01

Design concepts are developed and evaluated for a cooled structures assembly for the Scramjet engine, for engine subsystems mass, volume, and operating requirements, and for the aircraft/engine interface. A thermal protection system was defined that makes it possible to attain a life of 100 hours and 1000 cycles. The coolant equivalence ratio at the Mach 10 maximum thermal loading condition is 0.6, indicating a capacity for airframe cooling. The mechanical design is feasible for manufacture using conventional materials. For the cooled structures in a six-module engine, the mass per unit capture area is 12.4 KN/sq m. The total weight of a six-module engine assembly including the fuel system is 14.73 KN.

Comparison of Requirements for Composite Structures for Aircraft and Space Applications

NASA Technical Reports Server (NTRS)

Raju, Ivatury S.; Elliott, Kenny B.; Hampton, Roy W.; Knight, Norman F., Jr.; Aggarwal, Pravin; Engelstad, Stephen P.; Chang, James B.

2010-01-01

In this paper, the aircraft and space vehicle requirements for composite structures are compared. It is a valuable exercise to study composite structural design approaches used in the airframe industry, and to adopt methodology that is applicable for space vehicles. The missions, environments, analysis methods, analysis validation approaches, testing programs, build quantities, inspection, and maintenance procedures used by the airframe industry, in general, are not transferable to spaceflight hardware. Therefore, while the application of composite design approaches from other industries is appealing, many aspects cannot be directly utilized. Nevertheless, experiences and research for composite aircraft structures may be of use in unexpected arenas as space exploration technology develops, and so continued technology exchanges are encouraged.

Source Book of World War II Basic Data - Airframe Industry. Volume 1. Direct Man-Hours - Progress Curves

DTIC Science & Technology

1950-01-01

10 󈧰^0 29.0 4.0 0.0 6S.0 10 44.0 10.0 4.0 0.0 92.0 7 VI .0 18.0 6.0 3.0 0.0 64.0 6 114.0 36.0 11.0 4.0 0.0 63.0 8 131.0...Fighter) Spares i o VI /o Va 78 80 73 69 81 88 88 Republic, Farmingdale P-I7 C.U. 135 293 549 738 873 945 1010 1015 1112 1148 1274 1404 1508 1312...Entire Plane 7702 7879 7592 7120 6721 6721 Unit Airframe Weight 7300 7300 7300’ 7300 7300 7300 *l •swh

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendenhall, M.R.

The present volume discusses tactical missile aerodynamic drag, drag-prediction methods for axisymmetric missile bodies, an aerodynamic heating analysis for supersonic missiles, a component buildup method for engineering analysis of missiles at low-to-high angles of attack, experimental and analytical methods for missiles with noncircular fuselages, and a vortex-cloud model for body vortex shedding and tracking. Also discussed are panel methods with vorticity effects and corrections for nonlinear compressibility, supersonic full-potential methods for missile body analysis, space-marching Euler solvers, the time-asymptotic Euler/Navier-Stokes methods for subsonic and transonic flows, 3D boundary layers on missiles, Navier-Stokes analyses of flows over slender airframes, and themore » interaction of exhaust plumes with missile airframes.« less

NASA airframe structural integrity program

NASA Technical Reports Server (NTRS)

Harris, Charles E.

1991-01-01

NASA has initiated a research program with the long-term objective of supporting the aerospace industry in addressing issues related to the aging commercial transport fleet. The interdisciplinary program combines advanced fatigue crack growth prediction methodology with innovative nondestructive examination technology with the focus on multi-site damage (MSD) at riveted connections. A fracture mechanics evaluation of the concept of pressure proof testing the fuselage to screen for MSD has been completed. Also, a successful laboratory demonstration of the ability of the thermal flux method to detect disbonds at riveted lap splice joints has been conducted. All long-term program elements have been initiated and the plans for the methodology verification program are being coordinated with the airframe manufacturers.

NASA airframe structural integrity program

NASA Technical Reports Server (NTRS)

Harris, Charles E.

1990-01-01

NASA initiated a research program with the long-term objective of supporting the aerospace industry in addressing issues related to the aging of the commercial transport fleet. The program combines advanced fatigue crack growth prediction methodology with innovative nondestructive examination technology with the focus on multi-stage damage (MSD) at rivited connections. A fracture mechanics evaluation of the concept of pressure proof testing the fuselage to screen for MSD was completed. A successful laboratory demonstration of the ability of the thermal flux method to detect disbonds at rivited lap splice joints was conducted. All long-term program elements were initiated, and the plans for the methodology verification program are being coordinated with the airframe manufacturers.

Certification of the Cessna 152 on 100% ethanol

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shauck, M.E.; Zanin, M.G.

1997-12-31

In June 1996, the Renewable Aviation Fuels Development Center (RAFDC) at Baylor University in Waco, Texas, received a Supplemental Type Certificate (STC) for the use of 100% ethanol as a fuel for the Cessna 152, the most popular training aircraft in the world. This is the first certification granted by the Federal Aviation Administration (FAA) for a non-petroleum fuel. Certification of an aircraft on a new fuel requires a certification of the engine followed by a certification of the airframe/engine combination. This paper will describe the FAA airframe certification procedure, the tests required and their outcome using ethanol as anmore » aviation fuel in a Cessna 152.« less

Airframe noise of a small model transport aircraft and scaling effects. [Boeing 747

NASA Technical Reports Server (NTRS)

Shearin, J. G.

1981-01-01

Airframe noise of a 0.01 scale model Boeing 747 wide-body transport was measured in the Langley Anechoic Noise Facility. The model geometry simulated the landing and cruise configurations. The model noise was found to be similar in noise characteristics to that possessed by a 0.03 scale model 747. The 0.01 scale model noise data scaled to within 3 dB of full scale data using the same scaling relationships as that used to scale the 0.03 scale model noise data. The model noise data are compared with full scale noise data, where the full scale data are calculated using the NASA aircraft noise prediction program.

Airframe noise of a small model transport aircraft and scaling effects

NASA Astrophysics Data System (ADS)

Shearin, J. G.

1981-05-01

Airframe noise of a 0.01 scale model Boeing 747 wide-body transport was measured in the Langley Anechoic Noise Facility. The model geometry simulated the landing and cruise configurations. The model noise was found to be similar in noise characteristics to that possessed by a 0.03 scale model 747. The 0.01 scale model noise data scaled to within 3 dB of full scale data using the same scaling relationships as that used to scale the 0.03 scale model noise data. The model noise data are compared with full scale noise data, where the full scale data are calculated using the NASA aircraft noise prediction program.

Vibration analysis of the SA349/2 helicopter

NASA Technical Reports Server (NTRS)

Heffernan, Ruth; Precetti, Dominique; Johnson, Wayne

1991-01-01

Helicopter airframe vibration is examined using calculations and measurements for the SA349/2 research helicopter. The hub loads, which transmit excitations to the fuselage, are predicted using a comprehensive rotorcraft analysis and correlated with measuring hub loads. The predicted and measured hub loads are then coupled with finite element models representing the SA349/2 fuselage. The resulting vertical acceleration at the pilot seat is examined. Adjustments are made to the airframe structural models to examine the sensitivity of predicted vertical acceleration to the model. Changes of a few percent to the damping and frequency of specific models lead to large reductions in predicted vibration, and to major improvements in the correlations with measured pilot-seat vertical acceleration.

Propulsion Noise Reduction Research in the NASA Advanced Air Transport Technology Project

NASA Technical Reports Server (NTRS)

Van Zante, Dale; Nark, Douglas; Fernandez, Hamilton

2017-01-01

The Aircraft Noise Reduction (ANR) sub-project is focused on the generation, development, and testing of component noise reduction technologies progressing toward the NASA far term noise goals while providing associated near and mid-term benefits. The ANR sub-project has efforts in airframe noise reduction, propulsion (including fan and core) noise reduction, acoustic liner technology, and propulsion airframe aeroacoustics for candidate conventional and unconventional aircraft configurations. The current suite of propulsion specific noise research areas is reviewed along with emerging facility and measurement capabilities. In the longer term, the changes in engine and aircraft configuration will influence the suite of technologies necessary to reduce noise in next generation systems.

Investigation of contact acoustic nonlinearities on metal and composite airframe structures via intensity based health monitoring.

PubMed

Romano, P Q; Conlon, S C; Smith, E C

2013-01-01

Nonlinear structural intensity (NSI) and nonlinear structural surface intensity (NSSI) based damage detection techniques were improved and extended to metal and composite airframe structures. In this study, the measurement of NSI maps at sub-harmonic frequencies was completed to provide enhanced understanding of the energy flow characteristics associated with the damage induced contact acoustic nonlinearity mechanism. Important results include NSI source localization visualization at ultra-subharmonic (nf/2) frequencies, and damage detection results utilizing structural surface intensity in the nonlinear domain. A detection metric relying on modulated wave spectroscopy was developed and implemented using the NSSI feature. The data fusion of the intensity formulation provided a distinct advantage, as both the single interrogation frequency NSSI and its modulated wave extension (NSSI-MW) exhibited considerably higher sensitivities to damage than using single-sensor (strain or acceleration) nonlinear detection metrics. The active intensity based techniques were also extended to composite materials, and results show both NSSI and NSSI-MW can be used to detect damage in the bond line of an integrally stiffened composite plate structure with high sensitivity. Initial damage detection measurements made on an OH-58 tailboom (Penn State Applied Research Laboratory, State College, PA) indicate the techniques can be transitioned to complex airframe structures achieving high detection sensitivities with minimal sensors and actuators.

Design and Use of Microphone Directional Arrays for Aeroacoustic Measurements

NASA Technical Reports Server (NTRS)

Humphreys, William M., Jr.; Brooks, Thomas F.; Hunter, William W., Jr.; Meadows, Kristine R.

1998-01-01

An overview of the development of two microphone directional arrays for aeroacoustic testing is presented. These arrays were specifically developed to measure airframe noise in the NASA Langley Quiet Flow Facility. A large aperture directional array using 35 flush-mounted microphones was constructed to obtain high resolution noise localization maps around airframe models. This array possesses a maximum diagonal aperture size of 34 inches. A unique logarithmic spiral layout design was chosen for the targeted frequency range of 2-30 kHz. Complementing the large array is a small aperture directional array, constructed to obtain spectra and directivity information from regions on the model. This array, possessing 33 microphones with a maximum diagonal aperture size of 7.76 inches, is easily moved about the model in elevation and azimuth. Custom microphone shading algorithms have been developed to provide a frequency- and position-invariant sensing area from 10-40 kHz with an overall targeted frequency range for the array of 5-60 kHz. Both arrays are employed in acoustic measurements of a 6 percent of full scale airframe model consisting of a main element NACA 632-215 wing section with a 30 percent chord half-span flap. Representative data obtained from these measurements is presented, along with details of the array calibration and data post-processing procedures.

The Airframe Noise Reduction Challenge

NASA Technical Reports Server (NTRS)

Lockard, David P.; Lilley, Geoffrey M.

2004-01-01

The NASA goal of reducing external aircraft noise by 10 dB in the near-term presents the acoustics community with an enormous challenge. This report identifies technologies with the greatest potential to reduce airframe noise. Acoustic and aerodynamic effects will be discussed, along with the likelihood of industry accepting and implementing the different technologies. We investigate the lower bound, defined as noise generated by an aircraft modified with a virtual retrofit capable of eliminating all noise associated with the high lift system and landing gear. However, the airframe noise of an aircraft in this 'clean' configuration would only be about 8 dB quieter on approach than current civil transports. To achieve the NASA goal of 10 dB noise reduction will require that additional noise sources be addressed. Research shows that energy in the turbulent boundary layer of a wing is scattered as it crosses trailing edge. Noise generated by scattering is the dominant noise mechanism on an aircraft flying in the clean configuration. Eliminating scattering would require changes to much of the aircraft, and practical reduction devices have yet to receive serious attention. Evidence suggests that to meet NASA goals in civil aviation noise reduction, we need to employ emerging technologies and improve landing procedures; modified landing patterns and zoning restrictions could help alleviate aircraft noise in communities close to airports.

Propulsion system performance resulting from an integrated flight/propulsion control design

NASA Technical Reports Server (NTRS)

Mattern, Duane; Garg, Sanjay

1992-01-01

Propulsion-system-specific results are presented from the application of the integrated methodology for propulsion and airframe control (IMPAC) design approach to integrated flight/propulsion control design for a 'short takeoff and vertical landing' (STOVL) aircraft in transition flight. The IMPAC method is briefly discussed and the propulsion system specifications for the integrated control design are examined. The structure of a linear engine controller that results from partitioning a linear centralized controller is discussed. The details of a nonlinear propulsion control system are presented, including a scheme to protect the engine operational limits: the fan surge margin and the acceleration/deceleration schedule that limits the fuel flow. Also, a simple but effective multivariable integrator windup protection scheme is examined. Nonlinear closed-loop simulation results are presented for two typical pilot commands for transition flight: acceleration while maintaining flightpath angle and a change in flightpath angle while maintaining airspeed. The simulation nonlinearities include the airframe/engine coupling, the actuator and sensor dynamics and limits, the protection scheme for the engine operational limits, and the integrator windup protection. Satisfactory performance of the total airframe plus engine system for transition flight, as defined by the specifications, was maintained during the limit operation of the closed-loop engine subsystem.

Near-field commercial aircraft contribution to nitrogen oxides by engine, aircraft type, and airline by individual plume sampling.

PubMed

Carslaw, David C; Ropkins, Karl; Laxen, Duncan; Moorcroft, Stephen; Marner, Ben; Williams, Martin L

2008-03-15

Nitrogen oxides (NOx) concentrations were measured in individual plumes from aircraft departing on the northern runway at Heathrow Airport in west London. Over a period of four weeks 5618 individual plumes were sampled by a chemiluminescence monitor located 180 m from the runway. Results were processed and matched with detailed aircraft movement and aircraft engine data using chromatographic techniques. Peak concentrations associated with 29 commonly used engines were calculated and found to have a good relationship with N0x emissions taken from the International Civil Aviation Organization (ICAO) databank. However, it is found that engines with higher reported NOx emissions result in proportionately lower NOx concentrations than engines with lower emissions. We show that it is likely that aircraft operational factors such as takeoff weight and aircraftthrust setting have a measurable and important effect on concentrations of N0x. For example, NOx concentrations can differ by up to 41% for aircraft using the same airframe and engine type, while those due to the same engine type in different airframes can differ by 28%. These differences are as great as, if not greater than, the reported differences in NOx emissions between different engine manufacturers for engines used on the same airframe.

Airframe Noise from a Hybrid Wing Body Aircraft Configuration

NASA Technical Reports Server (NTRS)

Hutcheson, Florence V.; Spalt, Taylor B.; Brooks, Thomas F.; Plassman, Gerald E.

2016-01-01

A high fidelity aeroacoustic test was conducted in the NASA Langley 14- by 22-Foot Subsonic Tunnel to establish a detailed database of component noise for a 5.8% scale HWB aircraft configuration. The model has a modular design, which includes a drooped and a stowed wing leading edge, deflectable elevons, twin verticals, and a landing gear system with geometrically scaled wheel-wells. The model is mounted inverted in the test section and noise measurements are acquired at different streamwise stations from an overhead microphone phased array and from overhead and sideline microphones. Noise source distribution maps and component noise spectra are presented for airframe configurations representing two different approach flight conditions. Array measurements performed along the aircraft flyover line show the main landing gear to be the dominant contributor to the total airframe noise, followed by the nose gear, the inboard side-edges of the LE droop, the wing tip/LE droop outboard side-edges, and the side-edges of deployed elevons. Velocity dependence and flyover directivity are presented for the main noise components. Decorrelation effects from turbulence scattering on spectral levels measured with the microphone phased array are discussed. Finally, noise directivity maps obtained from the overhead and sideline microphone measurements for the landing gear system are provided for a broad range of observer locations.

Simulating the Impact Response of Full-Scale Composite Airframe Structures

NASA Technical Reports Server (NTRS)

Fasanella, Edwin L.; Jackson, Karen E.; Littell, Justin D.; Seal, Michael D.

2012-01-01

NASA Langley Research Center obtained a composite helicopter cabin structure in 2010 from the US Army's Survivable Affordable Repairable Airframe Program (SARAP) that was fabricated by Sikorsky Aircraft Corporation. The cabin had been subjected to a vertical drop test in 2008 to evaluate a tilting roof concept to limit the intrusion of overhead masses into the fuselage cabin. Damage to the cabin test article was limited primarily to the roof. Consequently, the roof area was removed and the remaining structure was cut into test specimens including a large subfloor section and a forward framed fuselage section. In 2011, NASA and Sikorsky entered into a cooperative research agreement to study the impact responses of composite airframe structures and to evaluate the capabilities of the explicit transient dynamic finite element code, LS-DYNA®, to simulate these responses including damage initiation and progressive failure. Most of the test articles were manufactured of graphite unidirectional tape composite with a thermoplastic resin system. However, the framed fuselage section was constructed primarily of a plain weave graphite fabric material with a thermoset resin system. Test data were collected from accelerometers and full-field photogrammetry. The focus of this paper will be to document impact testing and simulation results for the longitudinal impact of the subfloor section and the vertical drop test of the forward framed fuselage section.

An Airbreathing Launch Vehicle Design with Turbine-Based Low-Speed Propulsion and Dual Mode Scramjet High-Speed Propulsion

NASA Technical Reports Server (NTRS)

Moses, P. L.; Bouchard, K. A.; Vause, R. F.; Pinckney, S. Z.; Ferlemann, S. M.; Leonard, C. P.; Taylor, L. W., III; Robinson, J. S.; Martin, J. G.; Petley, D. H.

1999-01-01

Airbreathing launch vehicles continue to be a subject of great interest in the space access community. In particular, horizontal takeoff and horizontal landing vehicles are attractive with their airplane-like benefits and flexibility for future space launch requirements. The most promising of these concepts involve airframe integrated propulsion systems, in which the external undersurface of the vehicle forms part of the propulsion flowpath. Combining of airframe and engine functions in this manner involves all of the design disciplines interacting at once. Design and optimization of these configurations is a most difficult activity, requiring a multi-discipline process to analytically resolve the numerous interactions among the design variables. This paper describes the design and optimization of one configuration in this vehicle class, a lifting body with turbine-based low-speed propulsion. The integration of propulsion and airframe, both from an aero-propulsive and mechanical perspective are addressed. This paper primarily focuses on the design details of the preferred configuration and the analyses performed to assess its performance. The integration of both low-speed and high-speed propulsion is covered. Structural and mechanical designs are described along with materials and technologies used. Propellant and systems packaging are shown and the mission-sized vehicle weights are disclosed.

The new Section 23 of DO160C/ED14C lightning testing of externally mounted electrical equipment

NASA Astrophysics Data System (ADS)

Burrows, B. J. C.

1991-08-01

The new Section 23 is introduced which has only very recently been fully approved by the RTCA for incorporation into the first revision of DO160C/ED14C. Full threat lightning direct effects testing of equipment is entirely new to DO160, the only existing lightning testing is transient testing for LRU's (Line Replaceable Units) by pin or cable bundle injection methods, for equipment entirely contained within the airframe and assumed to be unaffected by direct effects. This testing required transients of very low amplitude compared with lightning itself, whereas the tests now to be described involve full threat lightning testing, that is using the previously established severe parameters of lightning appropriate to the Zone, such as 200 kA for Zone 1A as in AC20-136. Direct effects (i.e., damage) testing involves normally the lightning current arc attaching to the object under test (or very near to it) so submitting it to full potential for the electric, mechanical, thermal and shock damage which is caused by high current arcing. Since equipment for any part of the airframe require qualification, tests to demonstrate safety of equipment in fuel vapor regions of the airframe are also included.

Computational Analysis of a Chevron Nozzle Uniquely Tailored for Propulsion Airframe Aeroacoustics

NASA Technical Reports Server (NTRS)

Massey, Steven J.; Elmiligui, Alaa A.; Hunter, Craig A.; Thomas, Russell H.; Pao, S. Paul; Mengle, Vinod G.

2006-01-01

A computational flow field and predicted jet noise source analysis is presented for asymmetrical fan chevrons on a modern separate flow nozzle at take off conditions. The propulsion airframe aeroacoustic asymmetric fan nozzle is designed with an azimuthally varying chevron pattern with longer chevrons close to the pylon. A baseline round nozzle without chevrons and a reference nozzle with azimuthally uniform chevrons are also studied. The intent of the asymmetric fan chevron nozzle was to improve the noise reduction potential by creating a favorable propulsion airframe aeroacoustic interaction effect between the pylon and chevron nozzle. This favorable interaction and improved noise reduction was observed in model scale tests and flight test data and has been reported in other studies. The goal of this study was to identify the fundamental flow and noise source mechanisms. The flow simulation uses the asymptotically steady, compressible Reynolds averaged Navier-Stokes equations on a structured grid. Flow computations are performed using the parallel, multi-block, structured grid code PAB3D. Local noise sources were mapped and integrated computationally using the Jet3D code based upon the Lighthill Acoustic Analogy with anisotropic Reynolds stress modeling. In this study, trends of noise reduction were correctly predicted. Jet3D was also utilized to produce noise source maps that were then correlated to local flow features. The flow studies show that asymmetry of the longer fan chevrons near the pylon work to reduce the strength of the secondary flow induced by the pylon itself, such that the asymmetric merging of the fan and core shear layers is significantly delayed. The effect is to reduce the peak turbulence kinetic energy and shift it downstream, reducing overall noise production. This combined flow and noise prediction approach has yielded considerable understanding of the physics of a fan chevron nozzle designed to include propulsion airframe aeroacoustic interaction effects.

On the three-dimensional interaction of a rotor-tip vortex with a cylindrical surface

NASA Astrophysics Data System (ADS)

Radcliff, Thomas D.; Burggraf, Odus R.; Conlisk, A. T.

2000-12-01

The collision of a strong vortex with a surface is an important problem because significant impulsive loads may be generated. Prediction of helicopter fatigue lifetime may be limited by an inability to predict these loads accurately. Experimental results for the impingement of a helicopter rotor-tip vortex on a cylindrical airframe show a suction peak on the top of the airframe that strengthens and then weakens within milliseconds. A simple line-vortex model can predict the experimental results if the vortex is at least two vortex-core radii away from the airframe. After this, the model predicts continually deepening rather than lessening suction as the vortex stretches. Experimental results suggest that axial flow within the core of a tip vortex has an impact on the airframe pressure distribution upon close approach. The mechanism for this is hypothesized to be the inviscid redistribution of the vorticity field within the vortex as the axial velocity stagnates. Two models of a tip vortex with axial flow are considered. First, a classical axisymmetric line vortex with a cutoff parameter is superimposed with vortex ringlets suitably placed to represent the helically wound vortex shed by the rotor tip. Thus, inclusion of axial flow is found to advect vortex core thinning away from the point of closest interaction as the vortex stretches around the cylindrical surface during the collision process. With less local thinning, vorticity in the cutoff parameter model significantly overlaps the solid cylinder in an unphysical manner, highlighting the fact that the vortex core must deform from its original cylindrical shape. A second model is then developed in which axial and azimuthal vorticity are confined within a rectangular-section vortex. Area and aspect ratio of this vortex can be varied independently to simulate deformation of the vortex core. Both axial velocity and core deformation are shown to be important to calculate the local induced pressure loads properly. The computational results are compared with experiments conducted at the Georgia Institute of Technology.

Interaction of a Vortex with Axial Flow and a Cylindrical Surface

NASA Astrophysics Data System (ADS)

Radcliff, T. D.; Burgraff, O. R.; Conlisk, A. T.

1998-11-01

The direct collision of a vortex with a surface is an important problem because significant impulsive loads may be generated leading to premature fatigue. Experimental results for the impingement of a tip-vortex on a cylindrical airframe indicate that a suction peak forms on the top of the airframe which is subsequently reduced within milliseconds of vortex-surface contact. A simple line-vortex model can predict the experimental results until the vortex is within a vortex-core radius of the airframe. After this the model predicts continually deepening rather than lessening suction. Study of the experimental results suggests that axial flow within the core of a tip-vortex has an impact on the airframe pressure distribution upon close approach. The mechanism for this is hypothesized to be the inviscid redistribution of the vorticity field within the vortex coupled with deformation of the vortex core. Two models of a tip-vortex with axial flow are considered. First a classical line vortex with a cut-off parameter is superimposed with suitably placed vortex rings. This model simulates the helically wound vortex shed by the rotor tip. Inclusion of axial flow is found to prevent thinning of the vortex core as the vortex stretches around the cylindrical surface during the collision process. With less thinning, vorticity is observed to overlap the solid cylinder, highlighting the fact that the vortex core must deform from its original cylindrical shape. A second model is developed in which axial and azimuthal vorticity are uniformly distributed throughout a rectangular-section vortex. Area and aspect ratio of this vortex can be varied independently to simulate deformation of the vortex core. Both vorticity redistribution and core deformation are shown to be important to properly calculate the local induced pressure loads. The computational results are compared with the results of experiments conducted at the Georgia Institute of Technology.

Experimental Results of the 2.7% Reference H Nacelle Airframe Interference High Speed Civil Transport Model

NASA Technical Reports Server (NTRS)

Cappuccio, Gelsomina

1999-01-01

Experiments were conducted in the NASA Ames 9-Ft by 7-Ft Supersonic and 11-Ft by 11-Ft Transonic Wind Tunnels of a 2.7% Reference H (Ref. H) Nacelle Airframe Interference (NAI) High Speed Civil Transport (HSCT) model. NASA Ames did the experiment with the cooperation and assistance of Boeing and McDonnell Douglas. The Ref. H geometry was designed by Boeing. The model was built and tested by NASA under a license agreement with Boeing. Detailed forces and pressures of individual components of the configuration were obtained to assess nacelle airframe interference through the transonic and supersonic flight regime. The test apparatus was capable of measuring forces and pressures of the Wing body (WB) and nacelles. Axisymmetric and 2-D inlet nacelles were tested with the WB in both the in-proximity and captive mode. The in-proximity nacelles were mounted to a nacelle support system apparatus and were individually positioned. The right hand nacelles were force instrumented with flow through strain-gauged balances and the left hand nacelles were pressure instrumented. Mass flow ratio was varied to get steady state inlet unstart data. In addition, supersonic spillage data was taken by testing the 2-D inlet nacelles with ramps and the axisymmetric inlet nacelles with an inlet centerbody for the Mach condition of interest. The captive nacelles, both axisymmetric and 2-D, were attached to the WB via diverters. The captive 2-D inlet nacelle was also tested with ramps to get supersonic spillage data. Boeing analyzed the data and showed a drag penalty of four drag counts for the 2-D compared with the axisymmetric inlet nacelle. Two of the four counts were attributable to the external bevel designed into the 2-D inlet contour. Boeing and McDonnell Douglas used these data for evaluating Computational Fluid Dynamic (CFD) codes and for evaluation of nacelle airframe integration problems and solutions.

The Development of Two Composite Energy Absorbers for Use in a Transport Rotorcraft Airframe Crash Testbed (TRACT 2) Full-Scale Crash Test

NASA Technical Reports Server (NTRS)

Littell, Justin D.; Jackson, Karen E.; Annett, Martin S.; Seal, Michael D.; Fasanella, Edwin L.

2015-01-01

Two composite energy absorbers were developed and evaluated at NASA Langley Research Center through multi-level testing and simulation performed under the Transport Rotorcraft Airframe Crash Testbed (TRACT) research program. A conical-shaped energy absorber, designated the conusoid, was evaluated that consisted of four layers of hybrid carbon-Kevlar plain weave fabric oriented at [+45deg/-45deg/-45deg/+45deg] with respect to the vertical direction. A sinusoidal-shaped energy absorber, designated the sinusoid, was developed that consisted of hybrid carbon-Kevlar plain weave fabric face sheets, two layers for each face sheet oriented at +/-45deg with respect to the vertical direction, and a closed-cell ELFOAM P200 polyisocyanurate (2.0-lb/cu ft) foam core. The design goal for the energy absorbers was to achieve average floor-level accelerations of between 25- and 40-g during the full-scale crash test of a retrofitted CH-46E helicopter airframe, designated TRACT 2. Variations in both designs were assessed through dynamic crush testing of component specimens. Once the designs were finalized, subfloor beams of each configuration were fabricated and retrofitted into a barrel section of a CH-46E helicopter. A vertical drop test of the barrel section was conducted onto concrete to evaluate the performance of the energy absorbers prior to retrofit into TRACT 2. The retrofitted airframe was crash tested under combined forward and vertical velocity conditions onto soft soil. Finite element models were developed of all test articles and simulations were performed using LS-DYNA, a commercial nonlinear explicit transient dynamic finite element code. Test-analysis results are presented for each energy absorber as comparisons of time-history responses, as well as predicted and experimental structural deformations and progressive damage under impact loading for each evaluation level.

Integration of Propulsion-Airframe-Aeroacoustic Technologies and Design Concepts for a Quiet Blended-Wing-Body Transport

NASA Technical Reports Server (NTRS)

Hill, G. A.; Brown, S. A.; Geiselhart, K. A.

2004-01-01

This paper summarizes the results of studies undertaken to investigate revolutionary propulsion-airframe configurations that have the potential to achieve significant noise reductions over present-day commercial transport aircraft. Using a 300 passenger Blended-Wing-Body (BWB) as a baseline, several alternative low-noise propulsion-airframe-aeroacoustic (PAA) technologies and design concepts were investigated both for their potential to reduce the overall BWB noise levels, and for their impact on the weight, performance, and cost of the vehicle. Two evaluation frameworks were implemented for the assessments. The first was a Multi-Attribute Decision Making (MADM) process that used a Pugh Evaluation Matrix coupled with the Technique for Order Preference by Similarity to Ideal Solution (TOPSIS). This process provided a qualitative evaluation of the PAA technologies and design concepts and ranked them based on how well they satisfied chosen design requirements. From the results of the evaluation, it was observed that almost all of the PAA concepts gave the BWB a noise benefit, but degraded its performance. The second evaluation framework involved both deterministic and probabilistic systems analyses that were performed on a down-selected number of BWB propulsion configurations incorporating the PAA technologies and design concepts. These configurations included embedded engines with Boundary Layer Ingesting Inlets, Distributed Exhaust Nozzles installed on podded engines, a High Aspect Ratio Rectangular Nozzle, Distributed Propulsion, and a fixed and retractable aft airframe extension. The systems analyses focused on the BWB performance impacts of each concept using the mission range as a measure of merit. Noise effects were also investigated when enough information was available for a tractable analysis. Some tentative conclusions were drawn from the results. One was that the Boundary Layer Ingesting Inlets provided improvements to the BWB's mission range, by increasing the propulsive efficiency at cruise, and therefore offered a means to offset performance penalties imposed by some of the advanced PAA configurations. It was also found that the podded Distributed Exhaust Nozzle configuration imposed high penalties on the mission range and the need for substantial synergistic performance enhancements from an advanced integration scheme was identified. The High Aspect Ratio Nozzle showed inconclusive noise results and posed significant integration difficulties. Distributed Propulsion, in general, imposed performance penalties but may offer some promise for noise reduction from jet-to-jet shielding effects. Finally, a retractable aft airframe extension provided excellent noise reduction for a modest decrease in range.

Airframe Noise Prediction by Acoustic Analogy: Revisited

NASA Technical Reports Server (NTRS)

Farassat, F.; Casper, Jay H.; Tinetti, A.; Dunn, M. H.

2006-01-01

The present work follows a recent survey of airframe noise prediction methodologies. In that survey, Lighthill s acoustic analogy was identified as the most prominent analytical basis for current approaches to airframe noise research. Within this approach, a problem is typically modeled with the Ffowcs Williams and Hawkings (FW-H) equation, for which a geometry-independent solution is obtained by means of the use of the free-space Green function (FSGF). Nonetheless, the aeroacoustic literature would suggest some interest in the use of tailored or exact Green s function (EGF) for aerodynamic noise problems involving solid boundaries, in particular, for trailing edge (TE) noise. A study of possible applications of EGF for prediction of broadband noise from turbulent flow over an airfoil surface and the TE is, therefore, the primary topic of the present work. Typically, the applications of EGF in the literature have been limited to TE noise prediction at low Mach numbers assuming that the normal derivative of the pressure vanishes on the airfoil surface. To extend the application of EGF to higher Mach numbers, the uniqueness of the solution of the wave equation when either the Dirichlet or the Neumann boundary condition (BC) is specified on a deformable surface in motion. The solution of Lighthill s equation with either the Dirichlet or the Neumann BC is given for such a surface using EGFs. These solutions involve both surface and volume integrals just like the solution of FW-H equation using FSGF. Insight drawn from this analysis is evoked to discuss the potential application of EGF to broadband noise prediction. It appears that the use of a EGF offers distinct advantages for predicting TE noise of an airfoil when the normal pressure gradient vanishes on the airfoil surface. It is argued that such an approach may also apply to an airfoil in motion. However, for the prediction of broadband noise not directly associated with a trailing edge, the use of EGF does not appear to offer any advantages over the use of FSGF at the present stage of development. It is suggested here that the applications of EGF for airframe noise analysis be continued. As an example pertinent to airframe noise prediction, the Fast Scattering Code of NASA Langley is utilized to obtain the EGF numerically on the surface of a three dimensional wing with a flap and leading edge slat in uniform rectilinear motion. The interpretation and use of these numerical Green functions are then discussed.

Supersonic Cruise Research 1979, part 1

NASA Technical Reports Server (NTRS)

1980-01-01

Aerodynamics, stability and control, propulsion, and environmental factors of the supersonic cruise aircraft are discussed. Other topics include airframe structures and materials, systems integration, and economics.

Summary of the Tandem Cylinder Solutions from the Benchmark Problems for Airframe Noise Computations-I Workshop

NASA Technical Reports Server (NTRS)

Lockard, David P.

2011-01-01

Fifteen submissions in the tandem cylinders category of the First Workshop on Benchmark problems for Airframe Noise Computations are summarized. Although the geometry is relatively simple, the problem involves complex physics. Researchers employed various block-structured, overset, unstructured and embedded Cartesian grid techniques and considerable computational resources to simulate the flow. The solutions are compared against each other and experimental data from 2 facilities. Overall, the simulations captured the gross features of the flow, but resolving all the details which would be necessary to compute the noise remains challenging. In particular, how to best simulate the effects of the experimental transition strip, and the associated high Reynolds number effects, was unclear. Furthermore, capturing the spanwise variation proved difficult.

Full-Scale Crash Tests and Analyses of Three High-Wing Single

NASA Technical Reports Server (NTRS)

Annett, Martin S.; Littell, Justin D.; Stimson, Chad M.; Jackson, Karen E.; Mason, Brian H.

2015-01-01

The NASA Emergency Locator Transmitter Survivability and Reliability (ELTSAR) project was initiated in 2014 to assess the crash performance standards for the next generation of ELT systems. Three Cessna 172 aircraft have been acquired to conduct crash testing at NASA Langley Research Center's Landing and Impact Research Facility. Testing is scheduled for the summer of 2015 and will simulate three crash conditions; a flare to stall while emergency landing, and two controlled flight into terrain scenarios. Instrumentation and video coverage, both onboard and external, will also provide valuable data of airframe response. Full-scale finite element analyses will be performed using two separate commercial explicit solvers. Calibration and validation of the models will be based on the airframe response under these varying crash conditions.

Optimum Design of Hypersonic Airbreathing Propulsion

NASA Astrophysics Data System (ADS)

Kobayashi, Hiroaki; Sato, Tetsuya; Tanatsugu, Nobuhiro

The flight of Spaceplane is always under accelarating in the assent way and always under decelarating in the desent way and yet cruising in the return way. Besides, its flight envelope is considerably wider than that of airplane. Thus the integrated design method is required to build the best transportation system optimized taking into account the propulsion system and the airframe under the entire flight conditions. In this paper it is shown an optimization method on TSTO spaceplane system. Genetic algorithm (GA) was applied to optimize design parameters of engine, airframe, and trajectory simultaneously. Several types of engine were quantitatively compared using payload ratio as an evaluating function. It was concluded that precooled turbojets is the most promising engine for TSTO among Turbine Based Combined Cycle (TBCC) engines.

Comparison of Requirements for Composite Structures for Aircraft and Space Applications

NASA Technical Reports Server (NTRS)

Raju, Ivatury S.; Elliot, Kenny B.; Hampton, Roy W.; Knight, Norman F., Jr.; Aggarwal, Pravin; Engelstad, Stephen P.; Chang, James B.

2010-01-01

In this report, the aircraft and space vehicle requirements for composite structures are compared. It is a valuable exercise to study composite structural design approaches used in the airframe industry and to adopt methodology that is applicable for space vehicles. The missions, environments, analysis methods, analysis validation approaches, testing programs, build quantities, inspection, and maintenance procedures used by the airframe industry, in general, are not transferable to spaceflight hardware. Therefore, while the application of composite design approaches from aircraft and other industries is appealing, many aspects cannot be directly utilized. Nevertheless, experiences and research for composite aircraft structures may be of use in unexpected arenas as space exploration technology develops, and so continued technology exchanges are encouraged.

Coupled rotor/airframe vibration analysis program manual. Volume 2: Sample input and output listings

NASA Technical Reports Server (NTRS)

Cassarino, S.; Sopher, R.

1982-01-01

Sample input and output listings obtained with the base program (SIMVIB) of the coupled rotor/airframe vibration analysis and the external programs, G400/F389 and E927 are presented. Results for five of the base program test cases are shown. They represent different applications of the SIMVIB program to study the vibration characteristics of various dynamic configurations. Input and output listings obtained for one cycle of the G400/F389 coupled program are presented. Results from the rotor aeroelastic analysis E927 also appear. A brief description of the check cases is provided. A summary of the check cases for all the external programs interacting with the SIMVIB program is illustrated.

Correlation of AH-1G airframe flight vibration data with a coupled rotor-fuselage analysis

NASA Technical Reports Server (NTRS)

Sangha, K.; Shamie, J.

1990-01-01

The formulation and features of the Rotor-Airframe Comprehensive Analysis Program (RACAP) is described. The analysis employs a frequency domain, transfer matrix approach for the blade structural model, a time domain wake or momentum theory aerodynamic model, and impedance matching for rotor-fuselage coupling. The analysis is applied to the AH-1G helicopter, and a correlation study is conducted on fuselage vibration predictions. The purpose of the study is to evaluate the state-of-the-art in helicopter fuselage vibration prediction technology. The fuselage vibration predicted using RACAP are fairly good in the vertical direction and somewhat deficient in the lateral/longitudinal directions. Some of these deficiencies are traced to the fuselage finite element model.

Propulsion Airframe Integration Test Techniques for Hypersonic Airbreathing Configurations at NASA Langley Research Center

NASA Technical Reports Server (NTRS)

Witte, David W.; Huebner, Lawrence D.; Trexler, Carl A.; Cabell, Karen F.; Andrews, Earl H., Jr.

2003-01-01

The scope and significance of propulsion airframe integration (PAI) for hypersonic airbreathing vehicles is presented through a discussion of the PAI test techniques utilized at NASA Langley Research Center. Four primary types of PAI model tests utilized at NASA Langley for hypersonic airbreathing vehicles are discussed. The four types of PAI test models examined are the forebody/inlet test model, the partial-width/truncated propulsion flowpath test model, the powered exhaust simulation test model, and the full-length/width propulsion flowpath test model. The test technique for each of these four types of PAI test models is described, and the relevant PAI issues addressed by each test technique are illustrated through the presentation of recent PAI test data.

Inspection of aging aircraft: A manufacturer's perspective

NASA Technical Reports Server (NTRS)

Hagemaier, Donald J.

1992-01-01

Douglas, in conjunction with operators and regulators, has established interrelated programs to identify and address issues regarding inspection of aging aircraft. These inspection programs consist of the following: Supplemental Inspection Documents; Corrosion Prevention and Control Documents; Repair Assessment Documents; and Service Bulletin Compliance Documents. In addition, airframe manufacturers perform extended airframe fatigue tests to deal with potential problems before they can develop in the fleet. Lastly, nondestructive inspection (NDI) plays a role in all these programs through the detection of cracks, corrosion, and disbonds. However, improved and more cost effective NDI methods are needed. Some methods such as magneto-optic imaging, electronic shearography, Diffractor-Sight, and multi-parameter eddy current testing appear viable for near-term improvements in NDI of aging aircraft.

14 CFR 65.92 - Inspection authorization: Duration.

Code of Federal Regulations, 2012 CFR

2012-01-01

... (CONTINUED) AIRMEN CERTIFICATION: AIRMEN OTHER THAN FLIGHT CREWMEMBERS Mechanics § 65.92 Inspection... effective mechanic certificate with both a currently effective airframe rating and a currently effective...

14 CFR 65.92 - Inspection authorization: Duration.

Code of Federal Regulations, 2011 CFR

2011-01-01

... (CONTINUED) AIRMEN CERTIFICATION: AIRMEN OTHER THAN FLIGHT CREWMEMBERS Mechanics § 65.92 Inspection... effective mechanic certificate with both a currently effective airframe rating and a currently effective...

14 CFR 65.92 - Inspection authorization: Duration.

Code of Federal Regulations, 2013 CFR

2013-01-01

... (CONTINUED) AIRMEN CERTIFICATION: AIRMEN OTHER THAN FLIGHT CREWMEMBERS Mechanics § 65.92 Inspection... effective mechanic certificate with both a currently effective airframe rating and a currently effective...

14 CFR 65.92 - Inspection authorization: Duration.

Code of Federal Regulations, 2014 CFR

2014-01-01

... (CONTINUED) AIRMEN CERTIFICATION: AIRMEN OTHER THAN FLIGHT CREWMEMBERS Mechanics § 65.92 Inspection... effective mechanic certificate with both a currently effective airframe rating and a currently effective...

14 CFR 65.92 - Inspection authorization: Duration.

Code of Federal Regulations, 2010 CFR

2010-01-01

... (CONTINUED) AIRMEN CERTIFICATION: AIRMEN OTHER THAN FLIGHT CREWMEMBERS Mechanics § 65.92 Inspection... effective mechanic certificate with both a currently effective airframe rating and a currently effective...

The Development and Flight Testing of an Aerially Deployed Unmanned Aerial System

NASA Astrophysics Data System (ADS)

Smith, Andrew

An investigation into the feasibility of aerial deployed unmanned aerial vehicles was completed. The investigation included the development and flight testing of multiple unmanned aerial systems to investigate the different components of potential aerial deployment missions. The project consisted of two main objectives; the first objective dealt with the development of an airframe capable of surviving aerial deployment from a rocket and then self assembling from its stowed configuration into its flight configuration. The second objective focused on the development of an autopilot capable of performing basic guidance, navigation, and control following aerial deployment. To accomplish these two objectives multiple airframes were developed to verify their completion experimentally. The first portion of the project, investigating the feasibility of surviving an aerial deployment, was completed using a fixed wing glider that following a successful deployment had 52 seconds of controlled flight. Before developing the autopilot in the second phase of the project, the glider was significantly upgraded to fix faults discovered in the glider flight testing and to enhance the system capabilities. Unfortunately to conform to outdoor flight restrictions imposed by the university and the Federal Aviation Administration it was required to switch airframes before flight testing of the new fixed wing platform could begin. As a result, an autopilot was developed for a quadrotor and verified experimentally completely indoors to remain within the limits of governing policies.

STOL and STOVL hot gas ingestion and airframe heating tests in the NASA Lewis 9- by 15-foot low-speed wind tunnel

NASA Technical Reports Server (NTRS)

Johns, Albert L.

1989-01-01

Short takeoff and landing (STOL) and advanced short takeoff and vertical landing (STOVL) aircraft are being pursued for deployment near the end of this century. These concepts offer unique capabilities not seen in conventional aircraft: for example, shorter takeoff distances and the ability to operate from damaged runways and remote sites. However, special technology is critical to the development of this unique class of aircraft. Some of the real issues that are associated with these concepts are hot gas ingestion and airframe heating while in ground effects. Over the past nine years, NASA Lewis Research Center has been involved in several cooperative programs in the 9- by 15 Foot Low-Speed Wind Tunnel (LSWT) to establish a database for hot gas ingestion and airframe heating. The modifications are presented that were made in the 9- by 15-Foot LSWT, including the evolution of the ground plane, model support system, and tunnel sidewalls; and flow visualization techniques, instrumentation, test procedures, and test results. The 9- by 15-Foot LSWT tests were conducted at full scale exhaust nozzle pressure ratios. The headwind velocities varied from 8 to 120 kn depending on the concept (STOL or STOVL). Typical compressor-face distortions (pressure and temperature), ground plane contours, and model surface temperature profiles are presented.

Investigation of Volumetric Sources in Airframe Noise Simulations

NASA Technical Reports Server (NTRS)

Casper, Jay H.; Lockard, David P.; Khorrami, Mehdi R.; Streett, Craig L.

2004-01-01

Hybrid methods for the prediction of airframe noise involve a simulation of the near field flow that is used as input to an acoustic propagation formula. The acoustic formulations discussed herein are those based on the Ffowcs Williams and Hawkings equation. Some questions have arisen in the published literature in regard to an apparently significant dependence of radiated noise predictions on the location of the integration surface used in the solution of the Ffowcs Williams and Hawkings equation. These differences in radiated noise levels are most pronounced between solid-body surface integrals and off-body, permeable surface integrals. Such differences suggest that either a non-negligible volumetric source is contributing to the total radiation or the input flow simulation is suspect. The focus of the current work is the issue of internal consistency of the flow calculations that are currently used as input to airframe noise predictions. The case study for this research is a computer simulation for a three-element, high-lift wing profile during landing conditions. The noise radiated from this flow is predicted by a two-dimensional, frequency-domain formulation of the Ffowcs Williams and Hawkings equation. Radiated sound from volumetric sources is assessed by comparison of a permeable surface integration with the sum of a solid-body surface integral and a volume integral. The separate noise predictions are found in good agreement.

14 CFR 65.91 - Inspection authorization.

Code of Federal Regulations, 2014 CFR

2014-01-01

...) AIRMEN CERTIFICATION: AIRMEN OTHER THAN FLIGHT CREWMEMBERS Mechanics § 65.91 Inspection authorization. (a... effective mechanic certificate with both an airframe rating and a powerplant rating, each of which is...

14 CFR 65.91 - Inspection authorization.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) AIRMEN CERTIFICATION: AIRMEN OTHER THAN FLIGHT CREWMEMBERS Mechanics § 65.91 Inspection authorization. (a... effective mechanic certificate with both an airframe rating and a powerplant rating, each of which is...

14 CFR 65.91 - Inspection authorization.

Code of Federal Regulations, 2013 CFR

2013-01-01

...) AIRMEN CERTIFICATION: AIRMEN OTHER THAN FLIGHT CREWMEMBERS Mechanics § 65.91 Inspection authorization. (a... effective mechanic certificate with both an airframe rating and a powerplant rating, each of which is...

14 CFR 65.91 - Inspection authorization.

Code of Federal Regulations, 2012 CFR

2012-01-01

...) AIRMEN CERTIFICATION: AIRMEN OTHER THAN FLIGHT CREWMEMBERS Mechanics § 65.91 Inspection authorization. (a... effective mechanic certificate with both an airframe rating and a powerplant rating, each of which is...

14 CFR 65.91 - Inspection authorization.

Code of Federal Regulations, 2011 CFR

2011-01-01

...) AIRMEN CERTIFICATION: AIRMEN OTHER THAN FLIGHT CREWMEMBERS Mechanics § 65.91 Inspection authorization. (a... effective mechanic certificate with both an airframe rating and a powerplant rating, each of which is...

Coupled rotor-body vibrations with inplane degrees of freedom

NASA Technical Reports Server (NTRS)

Ming-Sheng, H.; Peters, D. A.

1985-01-01

In an effort to understand the vibration mechanisms of helicopters, the following basic studies are considered. A coupled rotor-fuselage vibration analysis including inplane degrees of freedom of both rotor and airframe is performed by matching of rotor and fuselage impedances at the hub. A rigid blade model including hub motion is used to set up the rotor flaplag equations. For the airframe, 9 degrees of freedom and hub offsets are used. The equations are solved by harmonic balance. For a 4-bladed rotor, the coupled responses and hub loads are calculated for various parameters in forward flight. The results show that the addition of inplane degrees of freedom does not significantly affect the vertical vibrations for the cases considered, and that inplane vibrations have similar resonance trends as do flapping vibrations.

FAA/NASA International Symposium on Advanced Structural Integrity Methods for Airframe Durability and Damage Tolerance

NASA Technical Reports Server (NTRS)

Harris, Charles E. (Editor)

1994-01-01

International technical experts in durability and damage tolerance of metallic airframe structures were assembled to present and discuss recent research findings and the development of advanced design and analysis methods, structural concepts, and advanced materials. The symposium focused on the dissemination of new knowledge and the peer-review of progress on the development of advanced methodologies. Papers were presented on: structural concepts for enhanced durability, damage tolerance, and maintainability; new metallic alloys and processing technology; fatigue crack initiation and small crack effects; fatigue crack growth models; fracture mechanics failure, criteria for ductile materials; structural mechanics methodology for residual strength and life prediction; development of flight load spectra for design and testing; and advanced approaches to resist corrosion and environmentally assisted fatigue.

Toward Improved CFD Predictions of Slender Airframe Aerodynamics Using the F-16XL Aircraft (CAWAPI-2)

NASA Technical Reports Server (NTRS)

Luckring, James M.; Rizzi, Arthur; Davis, M. Bruce

2014-01-01

A coordinated project has been underway to improve CFD predictions of slender airframe aerodynamics. The work is focused on two flow conditions and leverages a unique flight data set obtained with an F-16XL aircraft. These conditions, a low-speed high angleof- attack case and a transonic low angle-of-attack case, were selected from a prior prediction campaign wherein the CFD failed to provide acceptable results. In this paper the background, objectives and approach to the current project are presented. The work embodies predictions from multiple numerical formulations that are contributed from multiple organizations, and the context of this campaign to other multi-code, multiorganizational efforts is included. The relevance of this body of work toward future supersonic commercial transport concepts is also briefly addressed.

Nondestructive inspection assessment of eddy current and electrochemical analysis to separate inconel and stainless steel alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moore, D.G.; Sorensen, N.R.

1998-02-01

This report presents a nondestructive inspection assessment of eddy current and electrochemical analysis to separate inconel alloys from stainless steel alloys as well as an evaluation of cleaning techniques to remove a thermal oxide layer on aircraft exhaust components. The results of this assessment are presented in terms of how effective each technique classifies a known exhaust material. Results indicate that either inspection technique can separate inconel and stainless steel alloys. Based on the experiments conducted, the electrochemical spot test is the optimum for use by airframe and powerplant mechanics. A spot test procedure is proposed for incorporation into themore » Federal Aviation Administration Advisory Circular 65-9A Airframe & Powerplant Mechanic - General Handbook. 3 refs., 70 figs., 7 tabs.« less

PRSEUS Development for the Hybrid Wing Body Aircraft

NASA Technical Reports Server (NTRS)

Velicki, Alex; Jegley, Dawn

2011-01-01

NASA has created the Environmentally Responsible Aviation (ERA) Project to explore and document the feasibility, benefits and technical risk of advanced vehicle configurations and enabling technologies that will reduce the impact of aviation on the environment. A critical aspect of this pursuit is the development of a lighter, more robust airframe that will enable the introduction of unconventional aircraft configurations that have higher lift to drag ratios, reduced drag, and lower community noise. The primary structural concept being developed for the Hybrid Wing Body aircraft design under the ERA project in the Airframe Technology element is the PRSEUS concept. This paper describes how researchers at NASA and Boeing are working together to develop fundamental PRSEUS technologies that could someday be implemented on a transport size HWB airplane design.

Developing and utilizing an Euler computational method for predicting the airframe/propulsion effects for an aft-mounted turboprop transport. Volume 2: User guide

NASA Technical Reports Server (NTRS)

Chen, H. C.; Neback, H. E.; Kao, T. J.; Yu, N. Y.; Kusunose, K.

1991-01-01

This manual explains how to use an Euler based computational method for predicting the airframe/propulsion integration effects for an aft-mounted turboprop transport. The propeller power effects are simulated by the actuator disk concept. This method consists of global flow field analysis and the embedded flow solution for predicting the detailed flow characteristics in the local vicinity of an aft-mounted propfan engine. The computational procedure includes the use of several computer programs performing four main functions: grid generation, Euler solution, grid embedding, and streamline tracing. This user's guide provides information for these programs, including input data preparations with sample input decks, output descriptions, and sample Unix scripts for program execution in the UNICOS environment.

Planning, creating and documenting a NASTRAN finite element model of a modern helicopter

NASA Technical Reports Server (NTRS)

Gabal, R.; Reed, D.; Ricks, R.; Kesack, W.

1985-01-01

Mathematical models based on the finite element method of structural analysis as embodied in the NASTRAN computer code are widely used by the helicopter industry to calculate static internal loads and vibration of airframe structure. The internal loads are routinely used for sizing structural members. The vibration predictions are not yet relied on during design. NASA's Langley Research Center sponsored a program to conduct an application of the finite element method with emphasis on predicting structural vibration. The Army/Boeing CH-47D helicopter was used as the modeling subject. The objective was to engender the needed trust in vibration predictions using these models and establish a body of modeling guides which would enable confident future prediction of airframe vibration as part of the regular design process.

Robotic inspection of fiber reinforced composites using phased array UT

NASA Astrophysics Data System (ADS)

Stetson, Jeffrey T.; De Odorico, Walter

2014-02-01

Ultrasound is the current NDE method of choice to inspect large fiber reinforced airframe structures. Over the last 15 years Cartesian based scanning machines using conventional ultrasound techniques have been employed by all airframe OEMs and their top tier suppliers to perform these inspections. Technical advances in both computing power and commercially available, multi-axis robots now facilitate a new generation of scanning machines. These machines use multiple end effector tools taking full advantage of phased array ultrasound technologies yielding substantial improvements in inspection quality and productivity. This paper outlines the general architecture for these new robotic scanning systems as well as details the variety of ultrasonic techniques available for use with them including advances such as wide area phased array scanning and sound field adaptation for non-flat, non-parallel surfaces.

An advanced arc track resistant airframe wire

NASA Technical Reports Server (NTRS)

Beatty, J.

1995-01-01

Tensolite, a custom cable manufacturer specializing in high temperature materials as the dielectric medium, develops an advance arc track resistant airframe wire called Tufflite 2000. Tufflite 2000 has the following advantages over the other traditional wires: lighter weight and smaller in diameter; excellent wet and dry arc track resistance; superior dynamic cut-through performance even at elevated temperatures; flight proven performance on Boeing 737 and 757 airplanes; and true 260 C performance by utilizing Nickel plated copper conductors. This paper reports the different tests performed on Tufflite 2000: accelerated aging, arc resistance (wet and dry), dynamic cut through, humidity resistance, wire-to-wire abrasion, flammability, smoke, weight, notch sensitivity, flexibility, and markability. It particularly focuses on the BSI (British Standards Institute) dry arc resistance test and BSI wet arc tracking.

Aerodynamic Limits on Large Civil Tiltrotor Sizing and Efficiency

NASA Technical Reports Server (NTRS)

Acree, C W.

2014-01-01

The NASA Large Civil Tiltrotor (2nd generation, or LCTR2) is a useful reference design for technology impact studies. The present paper takes a broad view of technology assessment by examining the extremes of what aerodynamic improvements might hope to accomplish. Performance was analyzed with aerodynamically idealized rotor, wing, and airframe, representing the physical limits of a large tiltrotor. The analysis was repeated with more realistic assumptions, which revealed that increased maximum rotor lift capability is potentially more effective in improving overall vehicle efficiency than higher rotor or wing efficiency. To balance these purely theoretical studies, some practical limitations on airframe layout are also discussed, along with their implications for wing design. Performance of a less efficient but more practical aircraft with non-tilting nacelles is presented.

FAA/NASA International Symposium on Advanced Structural Integrity Methods for Airframe Durability and Damage Tolerance, part 2

NASA Technical Reports Server (NTRS)

Harris, Charles E. (Editor)

1994-01-01

The international technical experts in the areas of durability and damage tolerance of metallic airframe structures were assembled to present and discuss recent research findings and the development of advanced design and analysis methods, structural concepts, and advanced materials. The principal focus of the symposium was on the dissemination of new knowledge and the peer-review of progress on the development of advanced methodologies. Papers were presented on the following topics: structural concepts for enhanced durability, damage tolerance, and maintainability; new metallic alloys and processing technology; fatigue crack initiation and small crack effects; fatigue crack growth models; fracture mechanics failure criteria for ductile materials; structural mechanics methodology for residual strength and life prediction; development of flight load spectra for design and testing; and corrosion resistance.

Flight and analytical investigations of a structural mode excitation system on the YF-12A airplane

NASA Technical Reports Server (NTRS)

Goforth, E. A.; Murphy, R. C.; Beranek, J. A.; Davis, R. A.

1987-01-01

A structural excitation system, using an oscillating canard vane to generate force, was mounted on the forebody of the YF-12A airplane. The canard vane was used to excite the airframe structural modes during flight in the subsonic, transonic, and supersonic regimes. Structural modal responses generated by the canard vane forces were measured at the flight test conditions by airframe-mounted accelerometers. Correlations of analytical and experimental aeroelastic results were made. Doublet lattice, steady state double lattice with uniform lag, Mach box, and piston theory all produced acceptable analytical aerodynamic results within the restrictions that apply to each. In general, the aerodynamic theory methods, carefully applied, were found to predict the dynamic behavior of the YF-12A aircraft adequately.

Control Design Strategies to Enhance Long-Term Aircraft Structural Integrity

NASA Technical Reports Server (NTRS)

Newman, Brett A.

1999-01-01

Over the operational lifetime of both military and civil aircraft, structural components are exposed to hundreds of thousands of low-stress repetitive load cycles and less frequent but higher-stress transient loads originating from maneuvering flight and atmospheric gusts. Micro-material imperfections in the structure, such as cracks and debonded laminates, expand and grow in this environment, reducing the structural integrity and shortening the life of the airframe. Extreme costs associated with refurbishment of critical load-bearing structural components in a large fleet, or altogether reinventoring the fleet with newer models, indicate alternative solutions for life extension of the airframe structure are highly desirable. Increased levels of operational safety and reliability are also important factors influencing the desirability of such solutions. One area having significant potential for impacting crack growth/fatigue damage reduction and structural life extension is flight control. To modify the airframe response dynamics arising from command inputs and gust disturbances, feedback loops are routinely applied to vehicles. A dexterous flight control system architecture senses key vehicle motions and generates critical forces/moments at multiple points distributed throughout the airframe to elicit the desired motion characteristics. In principle, these same control loops can be utilized to influence the level of exposure to harmful loads during flight on structural components. Project objectives are to investigate and/or assess the leverage control has on reducing fatigue damage and enhancing long-term structural integrity, without degrading attitude control and trajectory guidance performance levels. In particular, efforts have focused on the effects inner loop control parameters and architectures have on fatigue damage rate. To complete this research, an actively controlled flexible aircraft model and a new state space modeling procedure for crack growth have been utilized. Analysis of the analytical state space model for crack growth revealed the critical mathematical factors, and hence the physical mechanism they represent, that influenced high rates of airframe crack growth. The crack model was then exercised with simple load inputs to uncover and expose key crack growth behavior. To characterize crack growth behavior, both "short-term" laboratory specimen test type inputs and "long-term" operational flight type inputs were considered. Harmonic loading with a single overload revealed typical exponential crack growth behavior until the overload application, after which time the crack growth was retarded for a period of time depending on the overload strength. An optimum overload strength was identified which leads to maximum retardation of crack growth. Harmonic loading with a repeated overload of varying strength and frequency again revealed an optimum overload trait for maximizing growth retardation. The optimum overload strength ratio lies near the range of 2 to 3 with dependency on frequency. Experimental data was found to correlate well with the analytical predictions.

High Bypass Ratio Jet Noise Reduction and Installation Effects Including Shielding Effectiveness

NASA Technical Reports Server (NTRS)

Thomas, Russell H.; Czech, Michael J.; Doty, Michael J.

2013-01-01

An experimental investigation was performed to study the propulsion airframe aeroacoustic installation effects of a separate flow jet nozzle with a Hybrid Wing Body aircraft configuration where the engine is installed above the wing. Prior understanding of the jet noise shielding effectiveness was extended to a bypass ratio ten application as a function of nozzle configuration, chevron type, axial spacing, and installation effects from additional airframe components. Chevron types included fan chevrons that are uniform circumferentially around the fan nozzle and T-fan type chevrons that are asymmetrical circumferentially. In isolated testing without a pylon, uniform chevrons compared to T-fan chevrons showed slightly more low frequency reduction offset by more high frequency increase. Phased array localization shows that at this bypass ratio chevrons still move peak jet noise source locations upstream but not to nearly the extent, as a function of frequency, as for lower bypass ratio jets. For baseline nozzles without chevrons, the basic pylon effect has been greatly reduced compared to that seen for lower bypass ratio jets. Compared to Tfan chevrons without a pylon, the combination with a standard pylon results in more high frequency noise increase and an overall higher noise level. Shielded by an airframe surface 2.17 fan diameters from nozzle to airframe trailing edge, the T-fan chevron nozzle can produce reductions in jet noise of as much as 8 dB at high frequencies and upstream angles. Noise reduction from shielding decreases with decreasing frequency and with increasing angle from the jet inlet. Beyond an angle of 130 degrees there is almost no noise reduction from shielding. Increasing chevron immersion more than what is already an aggressive design is not advantageous for noise reduction. The addition of airframe control surfaces, including vertical stabilizers and elevon deflection, showed only a small overall impact. Based on the test results, the best overall nozzle configuration design was selected for application to the N2A Hybrid Wing Body concept that will be the subject of the NASA Langley 14 by 22 Foot Subsonic Tunnel high fidelity aeroacoustic characterization experiment. The best overall nozzle selected includes T-fan type chevrons, uniform chevrons on the core nozzle, and no additional pylon of the type that created a strong acoustic effect at lower bypass ratios. The T-fan chevrons are oriented azimuthally away from the ground observer locations. This best overall nozzle compared to the baseline nozzle was assessed, at equal thrust, to produce sufficient installed noise reduction of the jet noise component to enable the N2A HWB to meet NASA s noise goal of 42 dB cumulative below Stage 4.

Small Airframe Manufacturer's Icing Perspective

NASA Technical Reports Server (NTRS)

Hoppins, Jim

2009-01-01

This viewgraph presentation describes the icing effects, risk mitigation practices, and icing certifications for various Cessna small aircraft models. NASA's role in the development of simulation tools for icing certifications is also discussed.

Proceedings of the SCAR Conference, Part 1

NASA Technical Reports Server (NTRS)

1976-01-01

The Supersonic Cruise Aircraft Research (SCAR) team analyzed six major topics: (1) aerodynamics, (2) stability and control, (3) propulsion, (4) environmental factor, (5) airframe structures and materials, and (6) design integration.

Data base for the prediction of airframe/propulsion system interference effects

NASA Technical Reports Server (NTRS)

Mcmillan, O. J.; Perkins, E. W.; Kuhn, G. D.; Perkins, S. C., Jr.

1979-01-01

Supersonic tactical aircraft with highly integrated jet propulsion systems were investigated. Primary attention was given to those interference effects which impact the external aerodynamics of the aircraft.

Revolutionary Aeropropulsion Concept for Sustainable Aviation: Turboelectric Distributed Propulsion

NASA Technical Reports Server (NTRS)

Kim, Hyun Dae; Felder, James L.; Tong, Michael. T.; Armstrong, Michael

2013-01-01

In response to growing aviation demands and concerns about the environment and energy usage, a team at NASA proposed and examined a revolutionary aeropropulsion concept, a turboelectric distributed propulsion system, which employs multiple electric motor-driven propulsors that are distributed on a large transport vehicle. The power to drive these electric propulsors is generated by separately located gas-turbine-driven electric generators on the airframe. This arrangement enables the use of many small-distributed propulsors, allowing a very high effective bypass ratio, while retaining the superior efficiency of large core engines, which are physically separated but connected to the propulsors through electric power lines. Because of the physical separation of propulsors from power generating devices, a new class of vehicles with unprecedented performance employing such revolutionary propulsion system is possible in vehicle design. One such vehicle currently being investigated by NASA is called the "N3-X" that uses a hybrid-wing-body for an airframe and superconducting generators, motors, and transmission lines for its propulsion system. On the N3-X these new degrees of design freedom are used (1) to place two large turboshaft engines driving generators in freestream conditions to minimize total pressure losses and (2) to embed a broad continuous array of 14 motor-driven fans on the upper surface of the aircraft near the trailing edge of the hybrid-wing-body airframe to maximize propulsive efficiency by ingesting thick airframe boundary layer flow. Through a system analysis in engine cycle and weight estimation, it was determined that the N3-X would be able to achieve a reduction of 70% or 72% (depending on the cooling system) in energy usage relative to the reference aircraft, a Boeing 777-200LR. Since the high-power electric system is used in its propulsion system, a study of the electric power distribution system was performed to identify critical dynamic and safety issues. This paper presents some of the features and issues associated with the turboelectric distributed propulsion system and summarizes the recent study results, including the high electric power distribution, in the analysis of the N3-X vehicle.

Feedback Control of Rotor Overspeed

NASA Technical Reports Server (NTRS)

Churchill, G. B.

1984-01-01

Feedback system for automatically governing helicopter rotor speed promises to lessen pilot's workload, enhance maneuverability, and protect airframe. With suitable modifications, concept applied to control speed of electrical generators, automotive engines and other machinery.

Overview of external Nacelle drag and interference drag

NASA Technical Reports Server (NTRS)

Neal, R. D.

1975-01-01

A historical view of multi-jet engine installations is given that emphasizes integration of the powerplant and the airframe in aircraft design for improved reduction in external nacelle drag and interference drag characteristics.

COMMERCIAL SUPERSONIC TRANSPORT PROGRAM. PHASE II-C REPORT. HIGH STRENGTH STEEL EVALUATION FOR SUPERSONIC AIRCRAFT.

DTIC Science & Technology

JET TRANSPORT AIRCRAFT, *AIRFRAMES, SUPERSONIC AIRCRAFT, STEEL , STRUCTURAL PROPERTIES, FRACTURE(MECHANICS), FATIGUE(MECHANICS), STRESS CORROSION...MICROPHOTOGRAPHY, HIGH TEMPERATURE, NICKEL ALLOYS, COBALT ALLOYS, CARBON, BAINITE , COMMERCIAL AIRCRAFT.

In Search of the Physics: The Interplay of Experiment and Computation in Slat Aeroacoustics

NASA Technical Reports Server (NTRS)

Khorrami, Mehdi R.; Choudhari, Meelan; Singer, Bart A.; Lockard, David P.; Streett, Craig L.

2003-01-01

The synergistic use of experiments and numerical simulations can uncover the underlying physics of airframe noise sources. We focus on the high-lift noise component associated with a leading-edge slat; flap side-edge noise is discussed in a companion paper by Streett et al. (2003). The present paper provides an overview of how slat noise was split into subcomponents and analyzed with carefully planned complementary experimental and numerical tests. We consider both tonal and broadband aspects of slat noise. The predicted far-field noise spectra are shown to be in good qualitative (and, to lesser extent, good quantitative agreement) with acoustic array measurements. Although some questions remain unanswered, the success of current airframe noise studies provides ample promise that remaining technical issues can be successfully addressed in the near future.

Ground vibration test of the XV-15 Tiltrotor Research Aircraft and pretest predictions

NASA Technical Reports Server (NTRS)

Studebaker, Karen; Abrego, Anita

1994-01-01

The first comprehensive ground vibration survey was performed on the XV-15 Tiltrotor Research Aircraft to measure the vibration modes of the airframe and to provide data critical for determining whirl flutter stability margins. The aircraft was suspended by the wings with bungee cords and cables. A NASTRAN finite element model was used in the design of the suspension system to minimize its interference with the wing modes. The primary objective of the test was to measure the dynamic characteristics of the wings and pylons for aeroelastic stability analysis. In addition, over 130 accelerometers were placed on the airframe to characterize the fuselage, wing, and tail vibration. Pretest predictions were made with the NASTRAN model as well as correlations with the test data. The results showed that the suspension system provided the isolation necessary for modal measurements.

Toward Improved Predictions of Slender Airframe Aerodynamics Using the F-16XL Aircraft

NASA Technical Reports Server (NTRS)

Luckring, James M.; Rizzi, Arthur; Davis, M. Bruce

2016-01-01

A coordinated project has been underway to improve computational fluid dynamics predictions of slender airframe aerodynamics. The work is focused on two flow conditions and leverages a unique flight data set obtained with an F-16XL aircraft. These conditions, a low-speed high angle-of-attack case and a transonic low angle-of-attack case, were selected from a prior prediction campaign wherein the computational fluid dynamics failed to provide acceptable results. In this paper, the background, objectives, and approach to the current project are presented. The work embodies predictions from multiple numerical formulations that are contributed from multiple organizations, and the context of this campaign to other multicode, multi-organizational efforts is included. The relevance of this body of work toward future supersonic commercial transport concepts is also briefly addressed.

Evaluation of active cooling systems for a Mach 6 hypersonic transport airframe, part 2

NASA Technical Reports Server (NTRS)

Helenbrook, R. G.; Mcconarty, W. A.; Anthony, F. M.

1971-01-01

Transpiration and convective cooling concepts are examined for the fuselage and tail surface of a Mach 6 hypersonic transport aircraft. Hydrogen, helium, and water are considered as coolants. Heat shields and radiation barriers are examined to reduce heat flow to the cooled structures. The weight and insulation requirements for the cryogenic fuel tanks are examined so that realistic totals can be estimated for the complete fuselage and tail. Structural temperatures are varied to allow comparison of aluminum alloy, titanium alloy, and superalloy contruction materials. The results of the study are combined with results obtained on the wing structure, obtained in a previous study, to estimate weights for the complete airframe. The concepts are compared among themselves, and with the uncooled concept on the basis of structural weight, cooling system weight, and coolant weight.

Analysis for the Progressive Failure Response of Textile Composite Fuselage Frames

NASA Technical Reports Server (NTRS)

Johnson, Eric R.; Boitnott, Richard L. (Technical Monitor)

2002-01-01

A part of aviation accident mitigation is a crashworthy airframe structure, and an important measure of merit for a crashworthy structure is the amount of kinetic energy that can be absorbed in the crush of the structure. Prediction of the energy absorbed from finite element analyses requires modeling the progressive failure sequence. Progressive failure modes may include material degradation, fracture and crack growth, and buckling and collapse. The design of crashworthy airframe components will benefit from progressive failure analyses that have been validated by tests. The subject of this research is the development of a progressive failure analysis for a textile composite, circumferential fuselage frame subjected to a quasi-static, crash-type load. The test data for the frame are reported, and these data are used to develop and to validate methods for the progressive failure response.

Hypersonic transport technology

NASA Technical Reports Server (NTRS)

Kirkham, F. S.; Hunt, J. L.

1977-01-01

The possibility of developing a hypersonic commercial transport (HST) for the early 21st century is explored in terms of potential performance characteristics and recent advances in propulsion and structures technology. Range-gross weight characteristics indicate that a 200 passenger, Mach 6 aircraft with a range of 9200 km (5000 n.mi.) would have a gross take-off weight not too different from that of current wide-body subsonic transports. The low cruise sonic boom overpressures generated by the HST opens the possibility of supersonic overland flight which, if permitted, would greatly increase the attractiveness of this type of aircraft. Recent advances in hypersonic propulsion systems and long-lived hypersonic aircraft structure are also discussed. The airframe-integrated scramjet and the actively-cooled airframe structure are identified as the most promising candidates for the HST and current approaches are described in some detail.

A model for rotorcraft flying qualities studies

NASA Technical Reports Server (NTRS)

Mittal, Manoj; Costello, Mark F.

1993-01-01

This paper outlines the development of a mathematical model that is expected to be useful for rotorcraft flying qualities research. A computer model is presented that can be applied to a range of different rotorcraft configurations. The algorithm computes vehicle trim and a linear state-space model of the aircraft. The trim algorithm uses non linear optimization theory to solve the nonlinear algebraic trim equations. The linear aircraft equations consist of an airframe model and a flight control system dynamic model. The airframe model includes coupled rotor and fuselage rigid body dynamics and aerodynamics. The aerodynamic model for the rotors utilizes blade element theory and a three state dynamic inflow model. Aerodynamics of the fuselage and fuselage empennages are included. The linear state-space description for the flight control system is developed using standard block diagram data.

Cirrus Airframe Parachute System and Odds of a Fatal Accident in Cirrus Aircraft Crashes.

PubMed

Alaziz, Mustafa; Stolfi, Adrienne; Olson, Dean M

2017-06-01

General aviation (GA) accidents have continued to demonstrate high fatality rates. Recently, ballistic parachute recovery systems (BPRS) have been introduced as a safety feature in some GA aircraft. This study evaluates the effectiveness and associated factors of the Cirrus Airframe Parachute System (CAPS) at reducing the odds of a fatal accident in Cirrus aircraft crashes. Publicly available Cirrus aircraft crash reports were obtained from the National Transportation Safety Board (NTSB) database for the period of January 1, 2001-December 31, 2016. Accident metrics were evaluated through univariate and multivariate analyses regarding odds of a fatal accident and use of the parachute system. Included in the study were 268 accidents. For CAPS nondeployed accidents, 82 of 211 (38.9%) were fatal as compared to 8 of 57 (14.0%) for CAPS deployed accidents. After controlling for all other factors, the adjusted odds ratio for a fatal accident when CAPS was not deployed was 13.1. The substantial increased odds of a fatal accident when CAPS was not deployed demonstrated the effectiveness of CAPS at providing protection of occupants during an accident. Injuries were shifted from fatal to serious or minor with the use of CAPS and postcrash fires were significantly reduced. These results suggest that BPRS could play a significant role in the next major advance in improving GA accident survival.Alaziz M, Stolfi A, Olson DM. Cirrus Airframe Parachute System and odds of a fatal accident in Cirrus aircraft crashes. Aerosp Med Hum Perform. 2017; 88(6):556-564.

Manufacturing and Cost Considerations in Multidisciplinary Aircraft Design (Research on Mathematical Modeling of Manufacturability Factors)

NASA Technical Reports Server (NTRS)

Rais-Rohani, Masoud

1996-01-01

The identification of airframe Manufacturability Factors/Cost Drivers (MFCD) and the method by which the relationships between MFCD and designer-controlled parameters could be properly modeled are described.

TRACT 2 Frame Drop Test AT NASA Langley Research Center's Landin

NASA Image and Video Library

2014-05-09

(Tract)2 Transport Rotorcraft Airframe Crash Testbed; Full Frame Drop Test: rotary wing crash worthiness, impact research at NASA Langley Research Center's Landing and Impact Research (LandIR) Facility Building 1297

Heat generation in aircraft tires under free rolling conditions

NASA Technical Reports Server (NTRS)

Clark, S. K.; Dodge, R. N.

1980-01-01

Effort is directed toward construction of a rational method for evaluating internal temperatures of aircraft tires. Enhanced predictability of tire temperature buildup is a design tool in both the tire and airframe industries.

The design of a wind tunnel VSTOL fighter model incorporating turbine powered engine simulators

NASA Technical Reports Server (NTRS)

Bailey, R. O.; Maraz, M. R.; Hiley, P. E.

1981-01-01

A wind-tunnel model of a supersonic VSTOL fighter aircraft configuration has been developed for use in the evaluation of airframe-propulsion system aerodynamic interactions. The model may be employed with conventional test techniques, where configuration aerodynamics are measured in a flow-through mode and incremental nozzle-airframe interactions are measured in a jet-effects mode, and with the Compact Multimission Aircraft Propulsion Simulator which is capable of the simultaneous simulation of inlet and exhaust nozzle flow fields so as to allow the evaluation of the extent of inlet and nozzle flow field coupling. The basic configuration of the twin-engine model has a geometrically close-coupled canard and wing, and a moderately short nacelle with nonaxisymmetric vectorable exhaust nozzles near the wing trailing edge, and may be converted to a canardless configuration with an extremely short nacelle. Testing is planned to begin in the summer of 1982.

Advanced stratified charge rotary aircraft engine design study

NASA Technical Reports Server (NTRS)

Badgley, P.; Berkowitz, M.; Jones, C.; Myers, D.; Norwood, E.; Pratt, W. B.; Ellis, D. R.; Huggins, G.; Mueller, A.; Hembrey, J. H.

1982-01-01

A technology base of new developments which offered potential benefits to a general aviation engine was compiled and ranked. Using design approaches selected from the ranked list, conceptual design studies were performed of an advanced and a highly advanced engine sized to provide 186/250 shaft Kw/HP under cruise conditions at 7620/25,000 m/ft altitude. These are turbocharged, direct-injected stratified charge engines intended for commercial introduction in the early 1990's. The engine descriptive data includes tables, curves, and drawings depicting configuration, performance, weights and sizes, heat rejection, ignition and fuel injection system descriptions, maintenance requirements, and scaling data for varying power. An engine-airframe integration study of the resulting engines in advanced airframes was performed on a comparative basis with current production type engines. The results show airplane performance, costs, noise & installation factors. The rotary-engined airplanes display substantial improvements over the baseline, including 30 to 35% lower fuel usage.

Calculated performance, stability and maneuverability of high-speed tilting-prop-rotor aircraft

NASA Technical Reports Server (NTRS)

Johnson, Wayne; Lau, Benton H.; Bowles, Jeffrey V.

1986-01-01

The feasibility of operating tilting-prop-rotor aircraft at high speeds is examined by calculating the performance, stability, and maneuverability of representative configurations. The rotor performance is examined in high-speed cruise and in hover. The whirl-flutter stability of the coupled-wing and rotor motion is calculated in the cruise mode. Maneuverability is examined in terms of the rotor-thrust limit during turns in helicopter configuration. Rotor airfoils, rotor-hub configuration, wing airfoil, and airframe structural weights representing demonstrated advance technology are discussed. Key rotor and airframe parameters are optimized for high-speed performance and stability. The basic aircraft-design parameters are optimized for minimum gross weight. To provide a focus for the calculations, two high-speed tilt-rotor aircraft are considered: a 46-passenger, civil transport and an air-combat/escort fighter, both with design speeds of about 400 knots. It is concluded that such high-speed tilt-rotor aircraft are quite practical.

Status of Advanced Stitched Unitized Composite Aircraft Structures

NASA Technical Reports Server (NTRS)

Jegley, Dawn C.; Velicki, Alex

2013-01-01

NASA has created the Environmentally Responsible Aviation (ERA) Project to explore and document the feasibility, benefits and technical risk of advanced vehicle configurations and enabling technologies that will reduce the impact of aviation on the environment. A critical aspect of this pursuit is the development of a lighter, more robust airframe that will enable the introduction of unconventional aircraft configurations that have higher lift-to-drag ratios, reduced drag, and lower community noise levels. The primary structural concept being developed under the ERA project in the Airframe Technology element is the Pultruded Rod Stitched Efficient Unitized Structure (PRSEUS) concept. This paper describes how researchers at NASA and The Boeing Company are working together to develop fundamental PRSEUS technologies that could someday be implemented on a transport size aircraft with high aspect ratio wings or unconventional shapes such as a hybrid wing body airplane design.

The development and evaluation of advanced Kevlar sandwich structure for application to rotorcraft airframes

NASA Astrophysics Data System (ADS)

Minguet, Pierre; Llorente, Steven; Fay, Russell

1991-05-01

The results of an evaluation of DuPont Kevlar-based material systems in sandwich structure designed for rotorcraft primary airframe structure are presented in this report. The focus of this work has been to evaluate the durability and compression strength of thin-gage Kevlar sandwich panels and investigate means of improvement. It was found that sandwich panels made with Kevlar 149 fibers can be as strong as Kevlar 49 structures but have reduced compression stiffness properties at typical operating strain levels. Thermal cycling was found to affect permeability but not strength in thin facesheet sandwich structure. Any increased permeability can be prevented with the use of an interleaf or surfacing plies. The surfacing plies investigated also had a beneficial effect on sandwich strength due to their stabilizing effect on the facesheet in compression. Finally, a previously developed model was used to analyze the residual strength of a sandwich panel after impact damage.

Corrosion and corrosion fatigue of airframe aluminum alloys

NASA Technical Reports Server (NTRS)

Chen, G. S.; Gao, M.; Harlow, D. G.; Wei, R. P.

1994-01-01

Localized corrosion and corrosion fatigue crack nucleation and growth are recognized as degradation mechanisms that effect the durability and integrity of commercial transport aircraft. Mechanically based understanding is needed to aid the development of effective methodologies for assessing durability and integrity of airframe components. As a part of the methodology development, experiments on pitting corrosion, and on corrosion fatigue crack nucleation and early growth from these pits were conducted. Pitting was found to be associated with constituent particles in the alloys and pit growth often involved coalescence of individual particle-nucleated pits, both laterally and in depth. Fatigue cracks typically nucleated from one of the larger pits that formed by a cluster of particles. The size of pit at which fatigue crack nucleates is a function of stress level and fatigue loading frequency. The experimental results are summarized, and their implications on service performance and life prediction are discussed.

Hydrodynamic impact of a system with a single elastic mode I : theory and generalized solution with an application to an elastic airframe

NASA Technical Reports Server (NTRS)

Mayo, Wilbur L

1952-01-01

Solutions of impact of a rigid prismatic float connected by a massless spring to a rigid upper mass are presented. The solutions are based on hydrodynamic theory which has been experimentally confirmed for a rigid structure. Equations are given for defining the spring constant and the ratio of the sprung mass to the lower mass so that the two-mass system provides representation of the fundamental mode of an airplane wing. The forces calculated are more accurate than the forces which would be predicted for a rigid airframe since the effect of the fundamental mode on the hydrodynamic force is taken into account. In a comparison of the theoretical data with data for a severe flight-test landing impact, the effect of the fundamental mode on the hydrodynamic force is considered and response data are compared with experimental data.

A Unified Model for Predicting the Open Hole Tensile and Compressive Strengths of Composite Laminates for Aerospace Applications

NASA Technical Reports Server (NTRS)

Davidson, Paul; Pineda, Evan J.; Heinrich, Christian; Waas, Anthony M.

2013-01-01

The open hole tensile and compressive strengths are important design parameters in qualifying fiber reinforced laminates for a wide variety of structural applications in the aerospace industry. In this paper, we present a unified model that can be used for predicting both these strengths (tensile and compressive) using the same set of coupon level, material property data. As a prelude to the unified computational model that follows, simplified approaches, referred to as "zeroth order", "first order", etc. with increasing levels of fidelity are first presented. The results and methods presented are practical and validated against experimental data. They serve as an introductory step in establishing a virtual building block, bottom-up approach to designing future airframe structures with composite materials. The results are useful for aerospace design engineers, particularly those that deal with airframe design.

Piloted Evaluation of an Integrated Methodology for Propulsion and Airframe Control Design

NASA Technical Reports Server (NTRS)

Bright, Michelle M.; Simon, Donald L.; Garg, Sanjay; Mattern, Duane L.; Ranaudo, Richard J.; Odonoghue, Dennis P.

1994-01-01

An integrated methodology for propulsion and airframe control has been developed and evaluated for a Short Take-Off Vertical Landing (STOVL) aircraft using a fixed base flight simulator at NASA Lewis Research Center. For this evaluation the flight simulator is configured for transition flight using a STOVL aircraft model, a full nonlinear turbofan engine model, simulated cockpit and displays, and pilot effectors. The paper provides a brief description of the simulation models, the flight simulation environment, the displays and symbology, the integrated control design, and the piloted tasks used for control design evaluation. In the simulation, the pilots successfully completed typical transition phase tasks such as combined constant deceleration with flight path tracking, and constant acceleration wave-off maneuvers. The pilot comments of the integrated system performance and the display symbology are discussed and analyzed to identify potential areas of improvement.

Developing and utilizing an Euler computational method for predicting the airframe/propulsion effects for an aft-mounted turboprop transport. Volume 1: Theory document

NASA Technical Reports Server (NTRS)

Chen, H. C.; Yu, N. Y.

1991-01-01

An Euler flow solver was developed for predicting the airframe/propulsion integration effects for an aft-mounted turboprop transport. This solver employs a highly efficient multigrid scheme, with a successive mesh-refinement procedure to accelerate the convergence of the solution. A new dissipation model was also implemented to render solutions that are grid insensitive. The propeller power effects are simulated by the actuator disk concept. An embedded flow solution method was developed for predicting the detailed flow characteristics in the local vicinity of an aft-mounted propfan engine in the presence of a flow field induced by a complete aircraft. Results from test case analysis are presented. A user's guide for execution of computer programs, including format of various input files, sample job decks, and sample input files, is provided in an accompanying volume.

Use of LS-DYNA(Registered TradeMark) to Assess the Energy Absorption Performance of a Shell-Based Kevlar(TradeMark)/Epoxy Composite Honeycomb

NASA Technical Reports Server (NTRS)

Polanco, Michael

2010-01-01

The forward and vertical impact stability of a composite honeycomb Deployable Energy Absorber (DEA) was evaluated during a full-scale crash test of an MD-500 helicopter at NASA Langley?s Landing and Impact Research Facility. The lower skin of the helicopter was retrofitted with DEA components to protect the airframe subfloor upon impact and to mitigate loads transmitted to Anthropomorphic Test Device (ATD) occupants. To facilitate the design of the DEA for this test, an analytical study was conducted using LS-DYNA(Registered TradeMark) to evaluate the performance of a shell-based DEA incorporating different angular cell orientations as well as simultaneous vertical and forward impact conditions. By conducting this study, guidance was provided in obtaining an optimum design for the DEA that would dissipate the kinetic energy of the airframe while maintaining forward and vertical impact stability.

NASA Heavy Lift Rotorcraft Systems Investigation

NASA Technical Reports Server (NTRS)

Johnson, Wayne; Yamauchi, Gloria K.; Watts, Michael E.

2005-01-01

The NASA Heavy Lift Rotorcraft Systems Investigation examined in depth several rotorcraft configurations for large civil transport, designed to meet the technology goals of the NASA Vehicle Systems Program. The investigation identified the Large Civil Tiltrotor as the configuration with the best potential to meet the technology goals. The design presented was economically competitive, with the potential for substantial impact on the air transportation system. The keys to achieving a competitive aircraft were low drag airframe and low disk loading rotors; structural weight reduction, for both airframe and rotors; drive system weight reduction; improved engine efficiency; low maintenance design; and manufacturing cost comparable to fixed-wing aircraft. Risk reduction plans were developed to provide the strategic direction to support a heavy-lift rotorcraft development. The following high risk areas were identified for heavy lift rotorcraft: high torque, light weight drive system; high performance, structurally efficient rotor/wing system; low noise aircraft; and super-integrated vehicle management system.

Fabrication and development of several heat pipe honeycomb sandwich panel concepts. [airframe integrated scramjet engine

NASA Technical Reports Server (NTRS)

Tanzer, H. J.

1982-01-01

The feasibility of fabricating and processing liquid metal heat pipes in a low mass honeycomb sandwich panel configuration for application on the NASA Langley airframe-integrated Scramjet engine was investigated. A variety of honeycomb panel facesheet and core-ribbon wick concepts was evaluated within constraints dictated by existing manufacturing technology and equipment. The chosen design consists of an all-stainless steel structure, sintered screen facesheets, and two types of core-ribbon; a diffusion bonded wire mesh and a foil-screen composite. Cleaning, fluid charging, processing, and process port sealing techniques were established. The liquid metals potassium, sodium and cesium were used as working fluids. Eleven honeycomb panels 15.24 cm X 15.24 cm X 2.94 cm were delivered to NASA Langley for extensive performance testing and evaluation; nine panels were processed as heat pipes, and two panels were left unprocessed.

Analysis for the Progressive Failure Response of Textile Composite Fuselage Frames

NASA Technical Reports Server (NTRS)

Johnson, Eric R.; Boitnott, Richard L. (Technical Monitor)

2002-01-01

A part of aviation accident mitigation is a crash worthy airframe structure, and an important measure of merit for a crash worthy structure is the amount of kinetic energy that can be absorbed in the crush of the structure. Prediction of the energy absorbed from finite element analyses requires modeling the progressive failure sequence. Progressive failure modes may include material degradation, fracture and crack growth, and buckling and collapse. The design of crash worthy airframe components will benefit from progressive failure analyses that have been validated by tests. The subject of this research is the development of a progressive failure analysis for textile composite. circumferential fuselage frames subjected to a quasi-static, crash-type load. The test data for these frames are reported, and these data, along with stub column test data, are to be used to develop and to validate methods for the progressive failure response.

Designs and Technology Requirements for Civil Heavy Lift Rotorcraft

NASA Technical Reports Server (NTRS)

Johnson, Wayne; Yamauchi, Gloria K.; Watts, Michael E.

2006-01-01

The NASA Heavy Lift Rotorcraft Systems Investigation examined in depth several rotorcraft configurations for large civil transport, designed to meet the technology goals of the NASA Vehicle Systems Program. The investigation identified the Large Civil Tiltrotor as the configuration with the best potential to meet the technology goals. The design presented was economically competitive, with the potential for substantial impact on the air transportation system. The keys to achieving a competitive aircraft were low drag airframe and low disk loading rotors; structural weight reduction, for both airframe and rotors; drive system weight reduction; improved engine efficiency; low maintenance design; and manufacturing cost comparable to fixed-wing aircraft. Risk reduction plans were developed to provide the strategic direction to support a heavy-lift rotorcraft development. The following high risk areas were identified for heavy lift rotorcraft: high torque, light weight drive system; high performance, structurally efficient rotor/wing system; low noise aircraft; and super-integrated vehicle management system.

Impact of broad-specification fuels on future jet aircraft. [engine components and performance

NASA Technical Reports Server (NTRS)

Grobman, J. S.

1978-01-01

The effects that broad specification fuels have on airframe and engine components were discussed along with the improvements in component technology required to use broad specification fuels without sacrificing performance, reliability, maintainability, or safety.

Damage tolerance assessment handbook. Volume 2 : airframe damage tolerance evaluation

DOT National Transportation Integrated Search

1999-02-01

The handbook is presented in two volumes. Volume I introduces the damage tolerance concept with an historical perspective followed by the fundamentals of fracture mechanics and fatigue crack propagation. Various fracture criteria and crack growth rul...

Cost consideration for aircraft configuration changes, 1

NASA Technical Reports Server (NTRS)

Tumlinson, R. R.

1975-01-01

The costs of improvements in aircraft drag reduction design changes are outlined in the context of production decisions. A drag reduction design with increased airframe weight requires cost increases for direct labor, overhead and direct expenses, plus general and administrative expenses.

Ramjets: Airframe Integration

DTIC Science & Technology

2010-09-01

nozzle • Brayton (or Joule) cycle: combustion at constant pressure at non-zero velocity The combustion process is modelled by means of adding heat to...against aerodynamic heating Aerodynamic heating calculations are based on: • Taylor -Maccoll method for compressible inviscid cone flow • Reynolds

41 CFR 102-39.60 - What restrictions and prohibitions apply to the exchange/sale of personal property?

Code of Federal Regulations, 2011 CFR

2011-01-01

... control equipment. 14 Guided missiles. 15 Aircraft and airframe structural components (except FSC Class... for FSC Class 1005, Guns through 30mm. Deviations are not required for Department of Defense (DoD...

77 FR 37879 - 36(b)(1) Arms Sales Notification

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-25

... provide greater security for its critical oil and natural gas infrastructure, and significant national... survivability equipment, displays, and sensors. The airframe itself does not contain sensitive technology...), Electro-Optic Missile Sensors (EOMSs), and Sequencer and Improved Countermeasures Dispenser (ICMD). The...

14 CFR 135.413 - Responsibility for airworthiness.

Code of Federal Regulations, 2011 CFR

2011-01-01

... engines, propellers, rotors, appliances, and parts, and shall have its aircraft maintained under this... maintenance, preventive maintenance, and alteration of its aircraft, including airframe, aircraft engines, propellers, rotors, appliances, emergency equipment and parts, under its manual and this chapter; or (2) Make...

14 CFR 135.413 - Responsibility for airworthiness.

Code of Federal Regulations, 2014 CFR

2014-01-01

... engines, propellers, rotors, appliances, and parts, and shall have its aircraft maintained under this... maintenance, preventive maintenance, and alteration of its aircraft, including airframe, aircraft engines, propellers, rotors, appliances, emergency equipment and parts, under its manual and this chapter; or (2) Make...

14 CFR 135.413 - Responsibility for airworthiness.

Code of Federal Regulations, 2013 CFR

2013-01-01

... engines, propellers, rotors, appliances, and parts, and shall have its aircraft maintained under this... maintenance, preventive maintenance, and alteration of its aircraft, including airframe, aircraft engines, propellers, rotors, appliances, emergency equipment and parts, under its manual and this chapter; or (2) Make...

14 CFR 135.413 - Responsibility for airworthiness.

Code of Federal Regulations, 2010 CFR

2010-01-01

... engines, propellers, rotors, appliances, and parts, and shall have its aircraft maintained under this... maintenance, preventive maintenance, and alteration of its aircraft, including airframe, aircraft engines, propellers, rotors, appliances, emergency equipment and parts, under its manual and this chapter; or (2) Make...

14 CFR 135.413 - Responsibility for airworthiness.

Code of Federal Regulations, 2012 CFR

2012-01-01

... engines, propellers, rotors, appliances, and parts, and shall have its aircraft maintained under this... maintenance, preventive maintenance, and alteration of its aircraft, including airframe, aircraft engines, propellers, rotors, appliances, emergency equipment and parts, under its manual and this chapter; or (2) Make...

Material fatigue data obtained by card-programmed hydraulic loading system

NASA Technical Reports Server (NTRS)

Davis, W. T.

1967-01-01

Fatigue tests using load distributions from actual loading histories encountered in flight are programmed on punched electronic accounting machine cards. With this hydraulic loading system, airframe designers can apply up to 55 load levels to a test specimen.

14 CFR 145.3 - Definition of terms.

Code of Federal Regulations, 2011 CFR

2011-01-01

... maintenance resulting from unforeseen events; or (2) Scheduled checks that contain servicing and/or... regulations and serving as the primary contact with the FAA. (b) Article means an aircraft, airframe, aircraft... for the work of a certificated repair station that performs maintenance, preventive maintenance...

14 CFR 145.3 - Definition of terms.

Code of Federal Regulations, 2013 CFR

2013-01-01

... maintenance resulting from unforeseen events; or (2) Scheduled checks that contain servicing and/or... regulations and serving as the primary contact with the FAA. (b) Article means an aircraft, airframe, aircraft... for the work of a certificated repair station that performs maintenance, preventive maintenance...

14 CFR 145.3 - Definition of terms.

Code of Federal Regulations, 2012 CFR

2012-01-01

... maintenance resulting from unforeseen events; or (2) Scheduled checks that contain servicing and/or... regulations and serving as the primary contact with the FAA. (b) Article means an aircraft, airframe, aircraft... for the work of a certificated repair station that performs maintenance, preventive maintenance...

14 CFR 145.3 - Definition of terms.

Code of Federal Regulations, 2014 CFR

2014-01-01

... maintenance resulting from unforeseen events; or (2) Scheduled checks that contain servicing and/or... regulations and serving as the primary contact with the FAA. (b) Article means an aircraft, airframe, aircraft... for the work of a certificated repair station that performs maintenance, preventive maintenance...

14 CFR 145.3 - Definition of terms.

Code of Federal Regulations, 2010 CFR

2010-01-01

... maintenance resulting from unforeseen events; or (2) Scheduled checks that contain servicing and/or... regulations and serving as the primary contact with the FAA. (b) Article means an aircraft, airframe, aircraft... for the work of a certificated repair station that performs maintenance, preventive maintenance...

Aviation Mechanic General, Airframe, and Powerplant Knowledge Test Guide

DOT National Transportation Integrated Search

1995-01-01

The FAA has available hundreds of computer testing centers nationwide. These testing centers offer the full range of airman knowledge tests. Refer to appendix 1 in this guide for a list of computer testing designees. This knowledge test guide was dev...

Motorless flight research, 1972. [glider design, airframes, and soaring flight developments

NASA Technical Reports Server (NTRS)

Nash-Webber, J. L. (Editor)

1973-01-01

The proceedings of a symposium on motorless flight research are presented. The subjects discussed are: (1) glider aerodynamic and design, (2) instrumentation, (3) structural concepts and materials, (4) soaring meteorology, (5) self-launching and ultralight sailplanes, and (6) performance testing.

77 FR 58791 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-09-24

... revision to the airworthiness limitations of the maintenance planning data document. This proposed AD would... information identified in this proposed AD, contact Boeing Commercial Airplanes, Attention: Data & Services... Marsh, Aerospace Engineer, Airframe Branch, ANM-120S, Seattle Aircraft Certification Office, FAA, 1601...

Control of propulsion systems for supersonic cruise aircraft

NASA Technical Reports Server (NTRS)

Hiller, K. W.; Drain, D. I.

1976-01-01

The propulsion control requirements of supersonic aircraft are presented. Integration of inlet, engine, and airframe controls is discussed. The application of recent control theory developments to propulsion control design is described. Control component designs for achieving reliable, responsive propulsion control are also discussed.

77 FR 31167 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-25

... Sutherland, Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office, 1601....sutherland@faa.gov . SUPPLEMENTARY INFORMATION: Discussion We issued a notice of proposed rulemaking (NPRM... this AD. (l) Related Information For more information about this AD, contact James Sutherland...

Materials and structures/ACEE

NASA Technical Reports Server (NTRS)

1981-01-01

Light weight composites made from graphite fibers, glass, or man made materials held in an epoxy matrix, and their application to airframe design are reviewed. The Aircraft Energy Efficiency program is discussed. Characteristics of composites, acceptable risks, building parts and confidence, and aeroelastic tailoring are considered.

GASP- General Aviation Synthesis Program. Volume 5: Weight

NASA Technical Reports Server (NTRS)

Hague, D.

1978-01-01

Subroutines for determining the weights of propulsion system related components and the airframe components of an aircraft configuration are presented. Subroutines that deal with design load conditions, aircraft balance, and tail sizing are included. Options for turbine and internal combustion engines are provided.

Revolution in airplane construction? Grob G110: The first modern fiber glass composition airplane shortly before its maiden flight

NASA Technical Reports Server (NTRS)

Dorpinghaus, R.

1982-01-01

A single engine two passenger airplane, constructed completely from fiber reinforced plastic materials is introduced. The cockpit, controls, wing profile, and landing gear are discussed. Development of the airframe is also presented.

Aviation Maintenance Technology. General. Curriculum Implementation Guide.

ERIC Educational Resources Information Center

Moore, John, Jr.; And Others

This curriculum implementation guide is a scope and sequence for the general section of a course in aviation maintenance technology. The course materials were prepared through a cooperative effort of airframe and powerplant mechanics, general aviation industry representatives, Federal Aviation Administration representatives, and vocational…

Active control of counter-rotating open rotor interior noise in a Dornier 728 experimental aircraft

NASA Astrophysics Data System (ADS)

Haase, Thomas; Unruh, Oliver; Algermissen, Stephan; Pohl, Martin

2016-08-01

The fuel consumption of future civil aircraft needs to be reduced because of the CO2 restrictions declared by the European Union. A consequent lightweight design and a new engine concept called counter-rotating open rotor are seen as key technologies in the attempt to reach this ambitious goals. Bearing in mind that counter-rotating open rotor engines emit very high sound pressures at low frequencies and that lightweight structures have a poor transmission loss in the lower frequency range, these key technologies raise new questions in regard to acoustic passenger comfort. One of the promising solutions for the reduction of sound pressure levels inside the aircraft cabin are active sound and vibration systems. So far, active concepts have rarely been investigated for a counter-rotating open rotor pressure excitation on complex airframe structures. Hence, the state of the art is augmented by the preliminary study presented in this paper. The study shows how an active vibration control system can influence the sound transmission of counter-rotating open rotor noise through a complex airframe structure into the cabin. Furthermore, open questions on the way towards the realisation of an active control system are addressed. In this phase, an active feedforward control system is investigated in a fully equipped Dornier 728 experimental prototype aircraft. In particular, the sound transmission through the airframe, the coupling of classical actuators (inertial and piezoelectric patch actuators) into the structure and the performance of the active vibration control system with different error sensors are investigated. It can be shown that the active control system achieves a reduction up to 5 dB at several counter-rotating open rotor frequencies but also that a better performance could be achieved through further optimisations.

Development of a SMA-Based, Slat-Gap Filler for Airframe Noise Reduction

NASA Technical Reports Server (NTRS)

Turner, Travis L.; Long, David L.

2015-01-01

Noise produced by unsteady flow around aircraft structures, termed airframe noise, is an important source of aircraft noise during the approach and landing phases of flight. Conventional leading-edge-slat devices for high lift on typical transport aircraft are a prominent source of airframe noise. Many concepts for slat noise reduction have been investigated. Slat-cove fillers have emerged as an attractive solution, but they maintain the gap flow, leaving some noise production mechanisms unabated, and thus represent a nonoptimal solution. Drooped-leading-edge (DLE) concepts have been proposed as "optimal" because the gap flow is eliminated. The deployed leading edge device is not distinct and separate from the main wing in DLE concepts and the high-lift performance suffers at high angles of attack (alpha) as a consequence. Elusive high-alpha performance and excessive weight penalty have stymied DLE development. The fact that high-lift performance of DLE systems is only affected at high alpha suggests another concept that simultaneously achieves the high-lift of the baseline airfoil and the noise reduction of DLE concepts. The concept involves utilizing a conventional leading-edge slat device and a deformable structure that is deployed from the leading edge of the main wing and closes the gap between the slat and main wing, termed a slat-gap filler (SGF). The deployable structure consists of a portion of the skin of the main wing and it is driven in conjunction with the slat during deployment and retraction. Benchtop models have been developed to assess the feasibility and to study important parameters. Computational models have assisted in the bench-top model design and provided valuable insight in the parameter space as well as the feasibility.

Reducing Propulsion Airframe Aeroacoustic Interactions with Uniquely Tailored Chevrons. 2; Installed Nozzles

NASA Technical Reports Server (NTRS)

Mengle, Vinod G.; Elkoby, Ronen; Brusniak, Leon; Thomas, Russ H.

2006-01-01

Propulsion airframe aeroacoustic (PAA) interactions arise due to the manner in which an engine is installed on the airframe and lead to an asymmetry in the flow/acoustic environment, for example, for under-the-wing installations due to the pylon, the wing and the high-lift devices. In this work we study how we can affect these PAA interactions to reduce the overall jet-related installed noise by tailoring the chevron shapes on fan and core nozzles in a unique fashion to take advantage of this asymmetry. In part 1 of this trio of papers we introduced the concept of azimuthally varying chevrons (AVC) and showed how some types of AVCs can be more beneficial than the conventional chevrons when tested on "isolated" scaled nozzles inclusive of the pylon effect. In this paper, we continue to study the effect of installing these AVC nozzles under a typical scaled modern wing with high-lift devices placed in a free jet. The noise benefits of these installed nozzles, as well as their installation effects are systematically studied for several fan/core AVC combinations at typical take-off conditions with high bypass ratio. We show, for example, that the top-enhanced mixing T-fan AVC nozzle (with enhanced mixing near the pylon and less mixing away from it) when combined with conventional chevrons on the core nozzle is quieter than conventional chevrons on both nozzles, and hardly produces any high-frequency lift, just as in the isolated case; however, its installed nozzle benefit is less than its isolated nozzle benefit. This suppression of take-off noise benefit under installed conditions, compared to its isolated nozzle benefit, is seen for all other chevron nozzles. We show how these relative noise benefits are related to the relative installation effects of AVCs and baseline nozzles.

Open Rotor Tone Shielding Methods for System Noise Assessments Using Multiple Databases

NASA Technical Reports Server (NTRS)

Bahr, Christopher J.; Thomas, Russell H.; Lopes, Leonard V.; Burley, Casey L.; Van Zante, Dale E.

2014-01-01

Advanced aircraft designs such as the hybrid wing body, in conjunction with open rotor engines, may allow for significant improvements in the environmental impact of aviation. System noise assessments allow for the prediction of the aircraft noise of such designs while they are still in the conceptual phase. Due to significant requirements of computational methods, these predictions still rely on experimental data to account for the interaction of the open rotor tones with the hybrid wing body airframe. Recently, multiple aircraft system noise assessments have been conducted for hybrid wing body designs with open rotor engines. These assessments utilized measured benchmark data from a Propulsion Airframe Aeroacoustic interaction effects test. The measured data demonstrated airframe shielding of open rotor tonal and broadband noise with legacy F7/A7 open rotor blades. Two methods are proposed for improving the use of these data on general open rotor designs in a system noise assessment. The first, direct difference, is a simple octave band subtraction which does not account for tone distribution within the rotor acoustic signal. The second, tone matching, is a higher-fidelity process incorporating additional physical aspects of the problem, where isolated rotor tones are matched by their directivity to determine tone-by-tone shielding. A case study is conducted with the two methods to assess how well each reproduces the measured data and identify the merits of each. Both methods perform similarly for system level results and successfully approach the experimental data for the case study. The tone matching method provides additional tools for assessing the quality of the match to the data set. Additionally, a potential path to improve the tone matching method is provided.

Future Jet Technologies. Part B. F-35 Future Risks v. JS-Education of Pilots & Engineers

NASA Astrophysics Data System (ADS)

Gal-Or, Benjamin

2011-09-01

Design of “Next-Generation” airframes based on supermarket-jet-engine-components is nowadays passé. A novel integration methodology [Gal-Or, “Editorial-Review, Part A”, 2011, Gal-Or, “Vectored Propulsion, Supermaneuverability and Robot Aircraft”, Springer Verlag, Gal-Or, Int'l. J. of Thermal and Fluid Sciences 7: 1-6, 1998, “Introduction”, 2011] is nowadays in. For advanced fighter aircraft it begins with JS-based powerplant, which takes up to three times longer to mature vis-à-vis the airframe, unless “committee's design” enforces a dormant catastrophe. Jet Steering (JS) or Thrust Vectoring Flight Control, is a classified, integrated engine-airframe technology aimed at maximizing post-stall-maneuverability, flight safety, efficiency and flight envelopes of manned and unmanned air vehicles, especially in the “impossible-to-fly”, post-stall flight domains where the 100+ years old, stall-spin-limited, Conventional Flight Control fails. Worldwide success in adopting the post-stall, JS-revolution, opens a new era in aviation, with unprecedented design variables identified here for a critical review of F-35 future risks v. future fleets of jet-steered, pilotless vehicles, like the X-47B/C. From the educational point of view, it is also instructive to comprehend the causes of long, intensive opposition to adopt post-stall, JS ideas. A review of such debates may also curb a future opposition to adopt more advanced, JS-based technologies, tests, strategies, tactics and missions within the evolving air, marine and land applications of JS. Most important, re-education of pilots and engineers requires adding post-stall, JS-based studies to curriculum & R&D.

Reported Back Pain in Army Aircrew in Relation to Airframe, Gender, Age, and Experience.

PubMed

Kelley, Amanda M; MacDonnell, Jason; Grigley, Deahndra; Campbell, John; Gaydos, Steven J

2017-02-01

Back pain has remained an issue of significance among aircraft crewmembers for decades, occurring in the majority of military helicopter pilots with potential deleterious effects on performance, safety, and operational readiness. This exploratory, correlational survey study was designed to evaluate the presence of patterns and relationships that may require further examination to understand causal factors. The study population consisted of U.S. Army aviation crewmembers. Subjects (467) completed an anonymous survey, including questions regarding demographics, airframes, experience, pain history and severity, ergonomics, mitigation strategies, and duty limitations. Overall, 84.6% of participants reported back pain at some time during their flying career, with 77.8% reporting back pain in the last calendar year. Age was found to significantly correlate with earlier time to pain during flight, higher pain rating after flight, and occurrence of grounding. A stepwise linear regression model was used to explore the relationships between age, flight hours, and years of aviation experience, demonstrating age to be the significant variable accounting for the observed variance. Aircrew reported wear of combat-related survival equipment and poor lumbar support to be the most notable contributors. Back pain rates were consistent with previous studies. The relationship of age to back pain in this study may highlight unique pathophysiological pathways that should be further investigated within an occupational context to better understand the etiologic role. Enhanced seated lumbar support and combat-related survival equipment remain relatively low-cost/high-yield topics worthy of further investigation for exploiting efficient means to improve health, safety, and operational performance.Kelley AM, MacDonnell J, Grigley D, Campbell J, Gaydos SJ. Reported back pain in army aircrew in relation to airframe, gender, age, and experience. Aerosp Med Hum Perform. 2017; 88(2):96-103.

Simulating the Impact Response of Composite Airframe Components

NASA Technical Reports Server (NTRS)

Jackson, Karen E.; Littell, Justin D.; Fasanella, Edwin L.

2014-01-01

In 2010, NASA Langley Research Center obtained residual hardware from the US Army's Survivable Affordable Repairable Airframe Program (SARAP). The hardware consisted of a composite fuselage section that was representative of the center section of a Black Hawk helicopter. The section was fabricated by Sikorsky Aircraft Corporation and designated the Test Validation Article (TVA). The TVA was subjected to a vertical drop test in 2008 to evaluate a tilting roof concept to limit the intrusion of overhead mass items, such as the rotor transmission, into the fuselage cabin. As a result of the 2008 test, damage to the hardware was limited primarily to the roof. Consequently, when the post-test article was obtained in 2010, the roof area was removed and the remaining structure was cut into six different types of test specimens including: (1) tension and compression coupons for material property characterization, (2) I-beam sections, (3) T-sections, (4) cruciform sections, (5) a large subfloor section, and (6) a forward framed fuselage section. In 2011, NASA and Sikorsky entered into a cooperative research agreement to study the impact responses of composite airframe structures and to evaluate the capabilities of the explicit transient dynamic finite element code, LS-DYNA®, to simulate these responses including damage initiation and progressive failure. Finite element models of the composite specimens were developed and impact simulations were performed. The properties of the composite material were represented using both a progressive in-plane damage model (Mat 54) and a continuum damage mechanics model (Mat 58) in LS-DYNA. This paper provides test-analysis comparisons of time history responses and the location and type of damage for representative I-beam, T-section, and cruciform section components.

Wind Tunnel Testing of a 120th Scale Large Civil Tilt-Rotor Model in Airplane and Helicopter Modes

NASA Technical Reports Server (NTRS)

Theodore, Colin R.; Willink, Gina C.; Russell, Carl R.; Amy, Alexander R.; Pete, Ashley E.

2014-01-01

In April 2012 and October 2013, NASA and the U.S. Army jointly conducted a wind tunnel test program examining two notional large tilt rotor designs: NASA's Large Civil Tilt Rotor and the Army's High Efficiency Tilt Rotor. The approximately 6%-scale airframe models (unpowered) were tested without rotors in the U.S. Army 7- by 10-foot wind tunnel at NASA Ames Research Center. Measurements of all six forces and moments acting on the airframe were taken using the wind tunnel scale system. In addition to force and moment measurements, flow visualization using tufts, infrared thermography and oil flow were used to identify flow trajectories, boundary layer transition and areas of flow separation. The purpose of this test was to collect data for the validation of computational fluid dynamics tools, for the development of flight dynamics simulation models, and to validate performance predictions made during conceptual design. This paper focuses on the results for the Large Civil Tilt Rotor model in an airplane mode configuration up to 200 knots of wind tunnel speed. Results are presented with the full airframe model with various wing tip and nacelle configurations, and for a wing-only case also with various wing tip and nacelle configurations. Key results show that the addition of a wing extension outboard of the nacelles produces a significant increase in the lift-to-drag ratio, and interestingly decreases the drag compared to the case where the wing extension is not present. The drag decrease is likely due to complex aerodynamic interactions between the nacelle and wing extension that results in a significant drag benefit.

Noise Scaling and Community Noise Metrics for the Hybrid Wing Body Aircraft

NASA Technical Reports Server (NTRS)

Burley, Casey L.; Brooks, Thomas F.; Hutcheson, Florence V.; Doty, Michael J.; Lopes, Leonard V.; Nickol, Craig L.; Vicroy, Dan D.; Pope, D. Stuart

2014-01-01

An aircraft system noise assessment was performed for the hybrid wing body aircraft concept, known as the N2A-EXTE. This assessment is a result of an effort by NASA to explore a realistic HWB design that has the potential to substantially reduce noise and fuel burn. Under contract to NASA, Boeing designed the aircraft using practical aircraft design princip0les with incorporation of noise technologies projected to be available in the 2020 timeframe. NASA tested 5.8% scale-mode of the design in the NASA Langley 14- by 22-Foot Subsonic Tunnel to provide source noise directivity and installation effects for aircraft engine and airframe configurations. Analysis permitted direct scaling of the model-scale jet, airframe, and engine shielding effect measurements to full-scale. Use of these in combination with ANOPP predictions enabled computations of the cumulative (CUM) noise margins relative to FAA Stage 4 limits. The CUM margins were computed for a baseline N2A-EXTE configuration and for configurations with added noise reduction strategies. The strategies include reduced approach speed, over-the-rotor line and soft-vane fan technologies, vertical tail placement and orientation, and modified landing gear designs with fairings. Combining the inherent HWB engine shielding by the airframe with added noise technologies, the cumulative noise was assessed at 38.7 dB below FAA Stage 4 certification level, just 3.3 dB short of the NASA N+2 goal of 42 dB. This new result shows that the NASA N+2 goal is approachable and that significant reduction in overall aircraft noise is possible through configurations with noise reduction technologies and operational changes.

Repair Options for Airframes

DTIC Science & Technology

2001-03-01

typical applications. This patch configuration can be best obtained with unidirectional tape . Woven material has greater formability and could also...1979. 15. Erdogan F and Arn K, "A Sandwich Plate With a Part-Through and a Debonding Crack," Engineering Fracture Mechanics, Vol. 4, June 1972. 16

Generation of spectra and stress histories for fatigue and damage tolerance analysis of fuselage repairs

DOT National Transportation Integrated Search

1991-10-01

This report describes a simplified procedure for the development of stress histories : for use in the analysis of aircraft repairs.- Although repairs of all components of : the airframe are of interest, this report concentrates on stress histories fo...

CFD application to subsonic inlet airframe integration. [computational fluid dynamics (CFD)

NASA Technical Reports Server (NTRS)

Anderson, Bernhard H.

1988-01-01

The fluid dynamics of curved diffuser duct flows of military aircraft is discussed. Three-dimensional parabolized Navier-Stokes analysis, and experiment techniques are reviewed. Flow measurements and pressure distributions are shown. Velocity vectors, and the effects of vortex generators are considered.

Pilot Cognitive Functioning and Training Outcomes

DTIC Science & Technology

2012-07-01

reducing physical stress and damage to the airframe. In summary, there has been extensive research in the USAF on the use of cognitive ability tests...has amassed a body of knowledge about many topics Comprehension Measures “social acculturation ,” “social intelligence,” and the conventional

77 FR 10411 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-22

... the AD docket shortly after receipt. FOR FURTHER INFORMATION CONTACT: James Sutherland, Aerospace...., Renton, Washington 98057-3356; phone: 425-917- 6533; fax: 425-917-6590; email: James.Sutherland@faa.gov... Sutherland, Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office, 1601...

14 CFR 43.2 - Records of overhaul and rebuilding.

Code of Federal Regulations, 2014 CFR

2014-01-01

... engine, propeller, appliance, or component part as being overhauled unless— (1) Using methods, techniques... may describe in any required maintenance entry or form an aircraft, airframe, aircraft engine, propeller, appliance, or component part as being rebuilt unless it has been disassembled, cleaned, inspected...

14 CFR 43.2 - Records of overhaul and rebuilding.

Code of Federal Regulations, 2013 CFR

2013-01-01

... engine, propeller, appliance, or component part as being overhauled unless— (1) Using methods, techniques... may describe in any required maintenance entry or form an aircraft, airframe, aircraft engine, propeller, appliance, or component part as being rebuilt unless it has been disassembled, cleaned, inspected...

14 CFR 43.2 - Records of overhaul and rebuilding.

Code of Federal Regulations, 2012 CFR

2012-01-01

... engine, propeller, appliance, or component part as being overhauled unless— (1) Using methods, techniques... may describe in any required maintenance entry or form an aircraft, airframe, aircraft engine, propeller, appliance, or component part as being rebuilt unless it has been disassembled, cleaned, inspected...

A study of the prediction of cruise noise and laminar flow control noise criteria for subsonic air transports

NASA Technical Reports Server (NTRS)

Swift, G.; Mungur, P.

1979-01-01

General procedures for the prediction of component noise levels incident upon airframe surfaces during cruise are developed. Contributing noise sources are those associated with the propulsion system, the airframe and the laminar flow control (LFC) system. Transformation procedures from the best prediction base of each noise source to the transonic cruise condition are established. Two approaches to LFC/acoustic criteria are developed. The first is a semi-empirical extension of the X-21 LFC/acoustic criteria to include sensitivity to the spectrum and directionality of the sound field. In the second, the more fundamental problem of how sound excites boundary layer disturbances is analyzed by deriving and solving an inhomogeneous Orr-Sommerfeld equation in which the source terms are proportional to the production and dissipation of sound induced fluctuating vorticity. Numerical solutions are obtained and compared with corresponding measurements. Recommendations are made to improve and validate both the cruise noise prediction methods and the LFC/acoustic criteria.

A Review of Noise and Vibration Control Technologies for Rotorcraft Transmissions

NASA Technical Reports Server (NTRS)

Scheidler, Justin J.; Asnani, Vivake M.

2016-01-01

An expanded commercial use of rotorcraft can alleviate runway congestion and improve the accessibility of routine air travel. To date, commercial use has been hindered by excessive cabin noise. The primary noise source is structure-borne vibration originating from the main rotor gearbox. Despite significant advancements in gear design, the gear mesh tones generated often exceed 100 dB. This paper summarizes the findings of a literature survey of vibration control technologies that serve to attenuate this vibration near the source, before it spreads into the airframe and produces noise. The scope is thus limited to vibration control treatments and modifications of the gears, driveline, housing structures, and the strut connections to the airframe. The findings of the literature are summarized and persistent and unresolved issues are identified. An emphasis is placed on components and systems that have been demonstrated in flight vehicles. Then, a discussion is presented of emerging technologies that have the potential to make significant advancements over the state of the art.

Design and Test of an Improved Crashworthiness Small Composite Airframe

NASA Technical Reports Server (NTRS)

Terry, James E.; Hooper, Steven J.; Nicholson, Mark

2002-01-01

The purpose of this small business innovative research (SBIR) program was to evaluate the feasibility of developing small composite airplanes with improved crashworthiness. A combination of analysis and half scale component tests were used to develop an energy absorbing airframe. Four full scale crash tests were conducted at the NASA Impact Dynamics Research Facility, two on a hard surface and two onto soft soil, replicating earlier NASA tests of production general aviation airplanes. Several seat designs and restraint systems including both an air bag and load limiting shoulder harnesses were tested. Tests showed that occupant loads were within survivable limits with the improved structural design and the proper combination of seats and restraint systems. There was no loss of cabin volume during the events. The analysis method developed provided design guidance but time did not allow extending the analysis to soft soil impact. This project demonstrated that survivability improvements are possible with modest weight penalties. The design methods can be readily applied by airplane designers using the examples in this report.

Selected results of the F-15 propulsion interactions program

NASA Technical Reports Server (NTRS)

Webb, L. D.; Nugent, J.

1982-01-01

A better understanding of propulsion system/airframe flow interactions could aid in the reduction of aircraft drag. For this purpose, NASA and the United States Air Force have conducted a series of wind-tunnel and flight tests on the F-15 airplane. This paper presents a correlation of flight test data from tests conducted at the NASA Dryden Flight Research Facility of the Ames Research Center, with data obtained from wind-tunnel tests. Flights were made at stabilized Mach numbers around 0.6, 0.9, 1.2, and 1.5 with accelerations up to near Mach number 2. Wind-tunnel tests used a 7.5 percent-scale F-15 inlet/airframe model. Flight and wind-tunnel pressure coefficients showed good agreement in most cases. Correlation of interaction effects caused by changes in cowl angle, angle-of-attack, and Mach number are presented. For the afterbody region, the pressure coefficients on the nozzle surfaces were influenced by boattail angles and Mach number. Boundary-layer thickness decreased as angle of attack increased above 4 deg.

Investigation of the Relationship of Vortex-Generated Sound and Airframe Noise

NASA Technical Reports Server (NTRS)

Smith, Sonya T.

1998-01-01

Airframe noise contributes the most to the environmental contamination from airports during take-off and landing. Two sources of noise are from the vortex-system associated with the slat and flap of multi-element wing designs. The flap-side edge vortex experiences bursting, known as vortex breakdown, at a critical deflection angle and experimental results show that this event may be one source of increased noise levels. Understanding of the edge roll-up phenomenon has increased but further focused studies on the role of the growth and bursting of the vortex structure are needed. The goal of the research is to plan a research program that will contribute to the understanding of the fluid physics of vortex breakdown and its relationship to noise production. The success of this program will lead to a priori predictions of when vortex breakdown will occur on the flap side-edge and accurate calculations of its effect on the noise level experienced by an observer near the aircraft during take-off and landing.

1999 NASA High-Speed Research Program Aerodynamic Performance Workshop. Volume 2; High Lift

NASA Technical Reports Server (NTRS)

Hahne, David E. (Editor)

1999-01-01

The High-Speed Research Program sponsored the NASA High-Speed Research Program Aerodynamic Performance Review on February 8-12, 1999 in Anaheim, California. The review was designed to bring together NASA and industry High-Speed Civil Transport (HSCT) Aerodynamic Performance technology development participants in areas of: Configuration Aerodynamics (transonic and supersonic cruise drag prediction and minimization) and High-Lift. The review objectives were to: (1) report the progress and status of HSCT aerodynamic performance technology development; (2) disseminate this technology within the appropriate technical communities; and (3) promote synergy among the scientist and engineers working HSCT aerodynamics. The HSR AP Technical Review was held simultaneously with the annual review of the following airframe technology areas: Materials and Structures, Environmental Impact, Flight Deck, and Technology Integration Thus, a fourth objective of the Review was to promote synergy between the Aerodynamic Performance technology area and the other technology areas within the airframe element of the HSR Program. This Volume 2/Part 1 publication presents the High-Lift Configuration Development session.

An Evaluation of the Applicability of Damage Tolerance to Dynamic Systems

NASA Technical Reports Server (NTRS)

Forth, Scott C.; Le, Dy; Turnberg, Jay

2005-01-01

The Federal Aviation Administration, the National Aeronautics and Space Administration and the aircraft industry have teamed together to develop methods and guidance for the safe life-cycle management of dynamic systems. Based on the success of the United States Air Force damage tolerance initiative for airframe structure, a crack growth based damage tolerance approach is being examined for implementation into the design and management of dynamic systems. However, dynamic systems accumulate millions of vibratory cycles per flight hour, more than 12,000 times faster than an airframe system. If a detectable crack develops in a dynamic system, the time to failure is extremely short, less than 100 flight hours in most cases, leaving little room for error in the material characterization, life cycle analysis, nondestructive inspection and maintenance processes. In this paper, the authors review the damage tolerant design process focusing on uncertainties that affect dynamic systems and evaluate the applicability of damage tolerance on dynamic systems.

The NASA/industry Design Analysis Methods for Vibrations (DAMVIBS) program: Sikorsky Aircraft: Advances toward interacting with the airframe design process

NASA Technical Reports Server (NTRS)

Twomey, William J.

1993-01-01

A short history is traced of the work done at Sikorsky Aircraft under the NASA/industry DAMVIBS program. This includes both work directly funded by the program as well as work which was internally funded but which received its initial impetus from DAMVIBS. The development of a finite element model of the UH-60A airframe having a marked improvement in vibration-predicting ability is described. A new program, PAREDYM, developed at Sikorsky, which automatically adjusts an FEM so that its modal characteristics match test values, is described, as well as the part this program played in the improvement of the UH-60A model. Effects of the bungee suspension system on the shake test data used for model verification are described. The impetus given by the modeling improvement, as well as the recent availability of PAREDYM, has brought for the first time the introduction of low-vibration design into the design cycle at Sikorsky.

National Aero-Space Plane team selects design

NASA Astrophysics Data System (ADS)

Kandebo, Stanley W.

1990-10-01

The selection of a design configuration for the NASP currently favors a directionally stable lifting body that incorporates dual stabilizers, short wings, and a two-man, dorsal crew compartment. The X-30 is expected to be 150-200 ft long and to have a takeoff gross weight of 250,000-300,000 lb. Three to five scramjet engines and a single 50,000 to 70,000 lb thrust rocket integrated into the airframe are expected to power the vehicle. The rocket will provide the X-30 with the burst of energy it will require to obtain orbital velocity and also to maneuver the craft out of earth orbit. Continuing propulsion and technical advances that include materials, aerodynamics, and simulations areas are being developed by program researchers. One of the most important achievements has been the progress made in locating the boundary-layer transition point on the NASP; engine, airframe integration, and flight-test issues are being addressed in separate study programs.

Assessment of NASA's Aircraft Noise Prediction Capability

NASA Technical Reports Server (NTRS)

Dahl, Milo D. (Editor)

2012-01-01

A goal of NASA s Fundamental Aeronautics Program is the improvement of aircraft noise prediction. This document provides an assessment, conducted from 2006 to 2009, on the current state of the art for aircraft noise prediction by carefully analyzing the results from prediction tools and from the experimental databases to determine errors and uncertainties and compare results to validate the predictions. The error analysis is included for both the predictions and the experimental data and helps identify where improvements are required. This study is restricted to prediction methods and databases developed or sponsored by NASA, although in many cases they represent the current state of the art for industry. The present document begins with an introduction giving a general background for and a discussion on the process of this assessment followed by eight chapters covering topics at both the system and the component levels. The topic areas, each with multiple contributors, are aircraft system noise, engine system noise, airframe noise, fan noise, liner physics, duct acoustics, jet noise, and propulsion airframe aeroacoustics.

First-Order Altitude Effects on the Cruise Efficiency of Subsonic Transport Aircraft

NASA Technical Reports Server (NTRS)

Guynn, Mark D.

2011-01-01

Aircraft fuel efficiency is a function of many different parameters, including characteristics of the engines, characteristics of the airframe, and the conditions under which the aircraft is operated. For a given vehicle, the airframe and engine characteristics are for the most part fixed quantities and efficiency is primarily a function of operational conditions. One important influence on cruise efficiency is cruise altitude. Various future scenarios have been postulated for cruise altitude, from the freedom to fly at optimum altitudes to altitude restrictions imposed for environmental reasons. This report provides background on the fundamental relationships determining aircraft cruise efficiency and examines the sensitivity of efficiency to cruise altitude. Analytical models of two current aircraft designs are used to derive quantitative results. Efficiency penalties are found to be generally less than 1% when within roughly 2000 ft of the optimum cruise altitude. Even the restrictive scenario of constant altitude cruise is found to result in a modest fuel consumption penalty if the fixed altitude is in an appropriate range.

COINS: A composites information database system

NASA Technical Reports Server (NTRS)

Siddiqi, Shahid; Vosteen, Louis F.; Edlow, Ralph; Kwa, Teck-Seng

1992-01-01

An automated data abstraction form (ADAF) was developed to collect information on advanced fabrication processes and their related costs. The information will be collected for all components being fabricated as part of the ACT program and include in a COmposites INformation System (COINS) database. The aim of the COINS development effort is to provide future airframe preliminary design and fabrication teams with a tool through which production cost can become a deterministic variable in the design optimization process. The effort was initiated by the Structures Technology Program Office (STPO) of the NASA LaRC to implement the recommendations of a working group comprised of representatives from the commercial airframe companies. The principal working group recommendation was to re-institute collection of composite part fabrication data in a format similar to the DOD/NASA Structural Composites Fabrication Guide. The fabrication information collection form was automated with current user friendly computer technology. This work in progress paper describes the new automated form and features that make the form easy to use by an aircraft structural design-manufacturing team.

Occupant Responses in a Full-Scale Crash Test of the Sikorsky ACAP Helicopter

NASA Technical Reports Server (NTRS)

Jackson, Karen E.; Fasanella, Edwin L.; Boitnott, Richard L.; McEntire, Joseph; Lewis, Alan

2002-01-01

A full-scale crash test of the Sikorsky Advanced Composite Airframe Program (ACAP) helicopter was performed in 1999 to generate experimental data for correlation with a crash simulation developed using an explicit nonlinear, transient dynamic finite element code. The airframe was the residual flight test hardware from the ACAP program. For the test, the aircraft was outfitted with two crew and two troop seats, and four anthropomorphic test dummies. While the results of the impact test and crash simulation have been documented fairly extensively in the literature, the focus of this paper is to present the detailed occupant response data obtained from the crash test and to correlate the results with injury prediction models. These injury models include the Dynamic Response Index (DRI), the Head Injury Criteria (HIC), the spinal load requirement defined in FAR Part 27.562(c), and a comparison of the duration and magnitude of the occupant vertical acceleration responses with the Eiband whole-body acceleration tolerance curve.

Auralization of Hybrid Wing Body Aircraft Flyover Noise from System Noise Predictions

NASA Technical Reports Server (NTRS)

Rizzi, Stephen A.; Aumann, Aric R.; Lopes, Leonvard V.; Burley, Casey L.

2013-01-01

System noise assessments of a state-of-the-art reference aircraft (similar to a Boeing 777-200ER with GE90-like turbofan engines) and several hybrid wing body (HWB) aircraft configurations were recently performed using NASA engine and aircraft system analysis tools. The HWB aircraft were sized to an equivalent mission as the reference aircraft and assessments were performed using measurements of airframe shielding from a series of propulsion airframe aeroacoustic experiments. The focus of this work is to auralize flyover noise from the reference aircraft and the best HWB configuration using source noise predictions and shielding data based largely on the earlier assessments. For each aircraft, three flyover conditions are auralized. These correspond to approach, sideline, and cutback operating states, but flown in straight and level flight trajectories. The auralizations are performed using synthesis and simulation tools developed at NASA. Audio and visual presentations are provided to allow the reader to experience the flyover from the perspective of a listener in the simulated environment.

An Evaluation of High Temperature Airframe Seals for Advanced Hypersonic Vehicles

NASA Technical Reports Server (NTRS)

DeMange, Jeffrey J.; Dunlap, Patrick H.; Steinetz, Bruce M.; Drlik, Gary J.

2007-01-01

High temperature seals are required for advanced hypersonic airframe applications. In this study, both spring tube thermal barriers and innovative wafer seal systems were evaluated under relevant hypersonic test conditions (temperatures, pressures, etc.) via high temperature compression testing and room temperature flow assessments. Thermal barriers composed of a Rene 41 spring tube filled with Saffil insulation and overbraided with a Nextel 312 sheath showed acceptable performance at 1500 F in both short term and longer term compression testing. Nextel 440 thermal barriers with Rene 41 spring tubes and Saffil insulation demonstrated good compression performance up to 1750 F. A silicon nitride wafer seal/compression spring system displayed excellent load performance at temperatures as high as 2200 F and exhibited room temperature leakage values that were only 1/3 those for the spring tube rope seals. For all seal candidates evaluated, no significant degradation in leakage resistance was noted after high temperature compression testing. In addition to these tests, a superalloy seal suitable for dynamic seal applications was optimized through finite element techniques.

The Aviation Paradox: Why We Can 'Know' Jetliners But Not Reactors.

PubMed

Downer, John

2017-01-01

Publics and policymakers increasingly have to contend with the risks of complex, safety-critical technologies, such as airframes and reactors. As such, 'technological risk' has become an important object of modern governance, with state regulators as core agents, and 'reliability assessment' as the most essential metric. The Science and Technology Studies (STS) literature casts doubt on whether or not we should place our faith in these assessments because predictively calculating the ultra-high reliability required of such systems poses seemingly insurmountable epistemological problems. This paper argues that these misgivings are warranted in the nuclear sphere, despite evidence from the aviation sphere suggesting that such calculations can be accurate. It explains why regulatory calculations that predict the reliability of new airframes cannot work in principle, and then it explains why those calculations work in practice. It then builds on this explanation to argue that the means by which engineers manage reliability in aviation is highly domain-specific, and to suggest how a more nuanced understanding of jetliners could inform debates about nuclear energy.

14 CFR Appendix C to Part 147 - Airframe Curriculum Subjects

Code of Federal Regulations, 2013 CFR

2013-01-01

... defueling. (1) 43. Inspect, check, and repair pressure fueling systems. (2) 44. Repair aircraft fuel system... repair aircraft fuel systems. g. aircraft electrical systems (2) 48. Repair and inspect aircraft... Components Teaching level a. aircraft landing gear systems (3) 29. Inspect, check, service, and repair...

14 CFR Appendix C to Part 147 - Airframe Curriculum Subjects

Code of Federal Regulations, 2010 CFR

2010-01-01

... defueling. (1) 43. Inspect, check, and repair pressure fueling systems. (2) 44. Repair aircraft fuel system... repair aircraft fuel systems. g. aircraft electrical systems (2) 48. Repair and inspect aircraft... Components Teaching level a. aircraft landing gear systems (3) 29. Inspect, check, service, and repair...

14 CFR Appendix C to Part 147 - Airframe Curriculum Subjects

Code of Federal Regulations, 2012 CFR

2012-01-01

... defueling. (1) 43. Inspect, check, and repair pressure fueling systems. (2) 44. Repair aircraft fuel system... repair aircraft fuel systems. g. aircraft electrical systems (2) 48. Repair and inspect aircraft... Components Teaching level a. aircraft landing gear systems (3) 29. Inspect, check, service, and repair...

14 CFR Appendix C to Part 147 - Airframe Curriculum Subjects

Code of Federal Regulations, 2014 CFR

2014-01-01

... defueling. (1) 43. Inspect, check, and repair pressure fueling systems. (2) 44. Repair aircraft fuel system... repair aircraft fuel systems. g. aircraft electrical systems (2) 48. Repair and inspect aircraft... Components Teaching level a. aircraft landing gear systems (3) 29. Inspect, check, service, and repair...

14 CFR Appendix C to Part 147 - Airframe Curriculum Subjects

Code of Federal Regulations, 2011 CFR

2011-01-01

... defueling. (1) 43. Inspect, check, and repair pressure fueling systems. (2) 44. Repair aircraft fuel system... repair aircraft fuel systems. g. aircraft electrical systems (2) 48. Repair and inspect aircraft... Components Teaching level a. aircraft landing gear systems (3) 29. Inspect, check, service, and repair...

77 FR 21429 - Airworthiness Directives; The Boeing Company Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-10

... the maintenance planning document. This AD requires revising the maintenance program to update... Engineer, Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office, 1601 Lind Avenue SW... Register on January 19, 2011 (76 FR 3054). That NPRM proposed to require revising the maintenance program...

14 CFR 183.25 - Technical personnel examiners.

Code of Federal Regulations, 2012 CFR

2012-01-01

... § 183.25 Technical personnel examiners. (a) A designated mechanic examiner (DME) (airframe and power plant) may— (1) Accept applications for, and conduct, mechanic, oral and practical tests necessary for issuing mechanic certificates under part 65 of this chapter; and (2) In the discretion of the appropriate...

14 CFR 183.25 - Technical personnel examiners.

Code of Federal Regulations, 2010 CFR

2010-01-01

... § 183.25 Technical personnel examiners. (a) A designated mechanic examiner (DME) (airframe and power plant) may— (1) Accept applications for, and conduct, mechanic, oral and practical tests necessary for issuing mechanic certificates under part 65 of this chapter; and (2) In the discretion of the appropriate...

14 CFR 183.25 - Technical personnel examiners.

Code of Federal Regulations, 2013 CFR

2013-01-01

... § 183.25 Technical personnel examiners. (a) A designated mechanic examiner (DME) (airframe and power plant) may— (1) Accept applications for, and conduct, mechanic, oral and practical tests necessary for issuing mechanic certificates under part 65 of this chapter; and (2) In the discretion of the appropriate...

14 CFR 183.25 - Technical personnel examiners.

Code of Federal Regulations, 2014 CFR

2014-01-01

... § 183.25 Technical personnel examiners. (a) A designated mechanic examiner (DME) (airframe and power plant) may— (1) Accept applications for, and conduct, mechanic, oral and practical tests necessary for issuing mechanic certificates under part 65 of this chapter; and (2) In the discretion of the appropriate...

14 CFR 183.25 - Technical personnel examiners.

Code of Federal Regulations, 2011 CFR

2011-01-01

... § 183.25 Technical personnel examiners. (a) A designated mechanic examiner (DME) (airframe and power plant) may— (1) Accept applications for, and conduct, mechanic, oral and practical tests necessary for issuing mechanic certificates under part 65 of this chapter; and (2) In the discretion of the appropriate...

14 CFR 25.473 - Landing load conditions and assumptions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... presence of systems or procedures significantly affects the lift. (c) The method of analysis of airplane... dynamic characteristics. (2) Spin-up and springback. (3) Rigid body response. (4) Structural dynamic response of the airframe, if significant. (d) The landing gear dynamic characteristics must be validated by...

14 CFR 91.1109 - Aircraft maintenance: Inspection program.

Code of Federal Regulations, 2011 CFR

2011-01-01

... be in writing and include at least the following information: (1) Instructions and procedures for the... TRANSPORTATION (CONTINUED) AIR TRAFFIC AND GENERAL OPERATING RULES GENERAL OPERATING AND FLIGHT RULES Fractional.... The instructions and procedures must set forth in detail the parts and areas of the airframe, engines...

14 CFR 91.1109 - Aircraft maintenance: Inspection program.

Code of Federal Regulations, 2013 CFR

2013-01-01

... be in writing and include at least the following information: (1) Instructions and procedures for the... TRANSPORTATION (CONTINUED) AIR TRAFFIC AND GENERAL OPERATING RULES GENERAL OPERATING AND FLIGHT RULES Fractional.... The instructions and procedures must set forth in detail the parts and areas of the airframe, engines...

14 CFR 23 - Certification and Balance Sheet Elements

Code of Federal Regulations, 2012 CFR

2012-01-01

... consideration received shall be reported. (2) “Other Paid-In Capital” shall include the difference between the... cross-referenced to the affected account or accounts. Schedule B-7 Airframe and Aircraft Engine... both passengers and cargo in combination. Data pertaining to aircraft engines shall be reported in...

Flexible Wing Designs with Sensor Control Feedback for Demonstration on the X-56A (MUTT)

NASA Technical Reports Server (NTRS)

Ginn, Starr

2012-01-01

Presenting an overview of the research DFRC is planning within the Subsonic Fixed Wing (SFW) Light Weight Airframes and Propulsion. Describ ing our TRL maturation and new research going forward using the X-56A as a validation testbed.

Australian DefenceScience. Volume 14, Number 1, Winter

DTIC Science & Technology

2006-01-01

with the advent of each new generation of aircraft. Advanced airframe repair technology Nearly all the surface of the JSF is to be constructed from...In December 2004, Defence signed a $1.4 billion contract with Spanish company, European Aeronautic Defence and Space Construcciones Aeronauticas SA

The Way Ahead For Maritime UAVS

DTIC Science & Technology

2006-10-23

of possible contract winners including Scan Eagle, Silver Fox, Wasp, Coyote and the USMC Tier I winner Dragon Eye. Technical data for these UAVs are...Neptune’s engine and avionics are placed above the waterline and the airframe is sealed for flotation as well as providing corrosion/water intrusion

Propulsion Airframe Aeroacoustic Integration Effects for a Hybrid Wing Body Aircraft Configuration

NASA Technical Reports Server (NTRS)

Czech, Michael J.; Thomas, Russell H; Elkoby, Ronen

2012-01-01

An extensive experimental investigation was performed to study the propulsion airframe aeroacoustic effects of a high bypass ratio engine for a hybrid wing body aircraft configuration where the engine is installed above the wing. The objective was to provide an understanding of the jet noise shielding effectiveness as a function of engine gas condition and location as well as nozzle configuration. A 4.7% scale nozzle of a bypass ratio seven engine was run at characteristic cycle points under static and forward flight conditions. The effect of the pylon and its orientation on jet noise was also studied as a function of bypass ratio and cycle condition. The addition of a pylon yielded significant spectral changes lowering jet noise by up to 4 dB at high polar angles and increasing it by 2 to 3 dB at forward angles. In order to assess jet noise shielding, a planform representation of the airframe model, also at 4.7% scale was traversed such that the jet nozzle was positioned from downstream of to several diameters upstream of the airframe model trailing edge. Installations at two fan diameters upstream of the wing trailing edge provided only limited shielding in the forward arc at high frequencies for both the axisymmetric and a conventional round nozzle with pylon. This was consistent with phased array measurements suggesting that the high frequency sources are predominantly located near the nozzle exit and, consequently, are amenable to shielding. The mid to low frequency sources were observed further downstream and shielding was insignificant. Chevrons were designed and used to impact the distribution of sources with the more aggressive design showing a significant upstream migration of the sources in the mid frequency range. Furthermore, the chevrons reduced the low frequency source levels and the typical high frequency increase due to the application of chevron nozzles was successfully shielded. The pylon was further modified with a technology that injects air through the shelf of the pylon which was effective in reducing low frequency noise and moving jet noise sources closer to the nozzle exit. In general, shielding effectiveness varied as a function of cycle condition with the cutback condition producing higher shielding compared to sideline power. The configuration with a more strongly immersed chevron and a pylon oriented opposite to the microphones produced the largest reduction in jet noise. In addition to the jet noise source, the shielding of a broadband point noise source was documented with up to 20 dB of noise reduction at directivity angles directly under the shielding surface.

Weight Assessment for Fuselage Shielding on Aircraft With Open-Rotor Engines and Composite Blade Loss

NASA Technical Reports Server (NTRS)

Carney, Kelly; Pereira, Michael; Kohlman, Lee; Goldberg, Robert; Envia, Edmane; Lawrence, Charles; Roberts, Gary; Emmerling, William

2013-01-01

The Federal Aviation Administration (FAA) has been engaged in discussions with airframe and engine manufacturers concerning regulations that would apply to new technology fuel efficient "openrotor" engines. Existing regulations for the engines and airframe did not envision features of these engines that include eliminating the fan blade containment systems and including two rows of counter-rotating blades. Damage to the airframe from a failed blade could potentially be catastrophic. Therefore the feasibility of using aircraft fuselage shielding was investigated. In order to establish the feasibility of this shielding, a study was conducted to provide an estimate for the fuselage shielding weight required to provide protection from an open-rotor blade loss. This estimate was generated using a two-step procedure. First, a trajectory analysis was performed to determine the blade orientation and velocity at the point of impact with the fuselage. The trajectory analysis also showed that a blade dispersion angle of 3deg bounded the probable dispersion pattern and so was used for the weight estimate. Next, a finite element impact analysis was performed to determine the required shielding thickness to prevent fuselage penetration. The impact analysis was conducted using an FAA-provided composite blade geometry. The fuselage geometry was based on a medium-sized passenger composite airframe. In the analysis, both the blade and fuselage were assumed to be constructed from a T700S/PR520 triaxially-braided composite architecture. Sufficient test data on T700S/PR520 is available to enable reliable analysis, and also demonstrate its good impact resistance properties. This system was also used in modeling the surrogate blade. The estimated additional weight required for fuselage shielding for a wing- mounted counterrotating open-rotor blade is 236 lb per aircraft. This estimate is based on the shielding material serving the dual use of shielding and fuselage structure. If the shielding material is not used for dual purpose, and is only used for shielding, then the additional weight per aircraft is estimated to be 428 lb. This weight estimate is based upon a number of assumptions that would need to be revised when applying this concept to an actual airplane design. For example, the weight savings that will result when there is no fan blade containment system, manufacturing limitations which may increase the weight where variable thicknesses was assumed, engine placement on the wing versus aft fuselage, etc.

Aircraft Mechanics Series. Duty Task List.

ERIC Educational Resources Information Center

Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This task list is intended for use in planning and/or evaluating a competency-based course in aircraft mechanics. The guide outlines the tasks entailed in 24 different duties typically required of employees in the following occupations: airframe mechanic, power plant mechanic, aircraft mechanic, aircraft sheet metal worker, aircraft electrician,…

Practical Application of Finite Element Analysis to Aircraft Structural Design

DTIC Science & Technology

1986-08-01

at the design stage AEROELASTICITE ET OPTIMISATION EN AVANT-PROJET (AA)PETIAU, C; (AB) BOUTIN , D. Avions Marcel Dassault-Breguet Aviation, Saint...Interscience, 1981, p. 431-443. 810000 p. 13 refs 8 In: EN (English) p. 2018 The design complexity and size of convectively-cooled engine and airframe

76 FR 3054 - Airworthiness Directives; The Boeing Company Model 777 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-19

... Airplanes, Attention: Data & Services Management, P. O. Box 3707, MC 2H-65, Seattle, Washington 98124-2207... after receipt. FOR FURTHER INFORMATION CONTACT: Duong Tran, Aerospace Engineer, Airframe Branch, ANM...: Comments Invited We invite you to send any written relevant data, views, or arguments about this proposal...

NASA and general aviation

NASA Technical Reports Server (NTRS)

Ethell, J. L.

1986-01-01

General aviation remains the single most misunderstood sector of aeronautics in the United States. A detailed look at how general aviation functions and how NASA helps keep it on the cutting edge of technology in airfoils, airframes, commuter travel, environmental concerns, engines, propellers, air traffic control, agricultural development, electronics, and safety is given.

75 FR 68249 - Policy Clarifying Definition of “Actively Engaged” for Purposes of Inspector Authorization

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-05

... exercising their mechanic certificate when employed full-time in aircraft maintenance to be actively engaged...) mechanic exercising the privileges of the mechanic certificate). An applicant can demonstrate that he or... applying. Note: Actively engaged means exercising the privileges of an airframe and powerplant mechanic...

Airframe Noise Prediction Method

DTIC Science & Technology

1977-03-01

llti ý b (t,. I’ ::~ ’! tl ’ : (l’il, • :t ’’!l t’, iI[ tw t hi[ i~i ,w n k w h~t <ich tt , ! iwlt ; .c h ’ti lt" . it :• , ’ . :: • I ! 1 z I< . r yv

14 CFR 91.417 - Maintenance records.

Code of Federal Regulations, 2010 CFR

2010-01-01

... alteration and records of the 100-hour, annual, progressive, and other required or approved inspections, as... propeller, and each rotor. (ii) The current status of life-limited parts of each airframe, engine, propeller... are required to be overhauled on a specified time basis. (iv) The current inspection status of the...

14 CFR 91.417 - Maintenance records.

Code of Federal Regulations, 2011 CFR

2011-01-01

... alteration and records of the 100-hour, annual, progressive, and other required or approved inspections, as... propeller, and each rotor. (ii) The current status of life-limited parts of each airframe, engine, propeller... are required to be overhauled on a specified time basis. (iv) The current inspection status of the...

14 CFR Section 23 - Certification and Balance Sheet Elements

Code of Federal Regulations, 2014 CFR

2014-01-01

... consideration received shall be reported. (2) “Other Paid-In Capital” shall include the difference between the... cross-referenced to the affected account or accounts. Schedule B-7 Airframe and Aircraft Engine... both passengers and cargo in combination. Data pertaining to aircraft engines shall be reported in...

14 CFR Section 23 - Certification and Balance Sheet Elements

Code of Federal Regulations, 2013 CFR

2013-01-01

... consideration received shall be reported. (2) “Other Paid-In Capital” shall include the difference between the... cross-referenced to the affected account or accounts. Schedule B-7 Airframe and Aircraft Engine... both passengers and cargo in combination. Data pertaining to aircraft engines shall be reported in...

Combat Maintenance Concepts and Repair Techniques for Helicopter Airframe Structures

DTIC Science & Technology

1981-01-01

probably more vulnerable to frontal and top hits than were aircraft operating in Viet Nam . And aircraft in terrain-following and nap-of-the-earth (NÖE...Addition of substantial weight and/or aerodynamic protrusions to the aircraft. 5. Neglect of finishing work ( cosmetic appearance). 6. Restrictions on

Civil Airlines/Air Services in Bangladesh, India and Pakistan. Volumes 1 thru 4.

DTIC Science & Technology

1985-03-01

endangers human life but it also has tremendous impact on the psychology of general travelling public on whose confidence the commercial aviation thrives...overhaul of SNECMA ATAR engines as well as the rebuilding of various airframes. The Kamra complex is equipped with electrical, hydraulic, instrument

Characterization of Al-Cu-Mg-Ag Alloy RX226-T8 Plate

NASA Technical Reports Server (NTRS)

Lach, Cynthia L.; Domack, Marcia S.

2003-01-01

Aluminum-copper-magnesium-silver (Al-Cu-Mg-Ag) alloys that were developed for thermal stability also offer attractive ambient temperature strength-toughness combinations, and therefore, can be considered for a broad range of airframe structural applications. The current study evaluated Al-Cu-Mg-Ag alloy RX226-T8 in plate gages and compared performance with sheet gage alloys of similar composition. Uniaxial tensile properties, plane strain initiation fracture toughness, and plane stress tearing resistance of RX226-T8 were examined at ambient temperature as a function of orientation and thickness location in the plate. Properties were measured near the surface and at the mid-plane of the plate. Tensile strengths were essentially isotropic, with variations in yield and ultimate tensile strengths of less than 2% as a function of orientation and through-thickness location. However, ductility varied by more than 15% with orientation. Fracture toughness was generally higher at the mid-plane and greater for the L-T orientation, although the differences were small near the surface of the plate. Metallurgical analysis indicated that the microstructure was primarily recrystallized with weak texture and was uniform through the plate with the exception of a fine-grained layer near the surface of the plate. Scanning electron microscope analysis revealed Al-Cu-Mg second phase particles which varied in composition and were primarily located on grain boundaries parallel to the rolling direction. Fractography of toughness specimens for both plate locations and orientations revealed that fracture occurred predominantly by transgranular microvoid coalescence. Introduction High-strength, low-density Al-Cu-Mg-Ag alloys were initially developed to replace conventional 2000 (Al-Cu-Mg) and 7000 (Al-Zn-Cu-Mg) series aluminum alloys for aircraft structural applications [1]. During the High Speed Civil Transport (HSCT) program, improvements in thermal stability were demonstrated for candidate aircraft wing and fuselage skin materials through the addition of silver to Al-Cu-Mg alloys based on Al 2519 chemistry [2]. Thermal stability of the resulting Al-Cu-Mg-Ag alloys, C415-T8 and C416-T8, was due to co-precipitation of the thermally stable . (AlCu) and ' (Al2Cu) strengthening phases [1-4]. The strength and toughness behavior was investigated for these alloys produced as 0.090-inch thick rolled sheet in the T8 condition and after various thermal exposures. The mechanical properties were shown to be competitive with conventional aircraft alloys, 2519-T8 and 2618-T8 [2]. During the Integral Airframe Structure (IAS) program, advanced aluminum alloys were examined for use in an integrally stiffened airframe structure where the skin and stiffeners would be machined from plate and extruded frames would be mechanically attached (see Figure 1) [5]. Advantages of integrally stiffened structure include reduced part count, and reduced assembly times compared to conventional built-up airframe structure. The near-surface properties of a thick plate are of significance for a machined integrally stiffened airframe structure since this represents the skin location. Properties measured at the mid-plane of the plate are more representative of the stiffener web. RX226 was developed to exploit strength-toughness improvements and thermal stability benefits of Al-Cu-Mg-Ag alloys in plate gages. This study evaluated the microstructure and properties of three gages of plate produced in the T8 condition.

Flight Path

ERIC Educational Resources Information Center

Ernst, Heidi

2004-01-01

Aviation High is a career and technical education school in the Long Island City neighborhood of Queens and the nation's largest aviation-focused high school. Required courses for all 2,000 students include the usual English, math, science, and foreign languages, but also airframe and power plant shops. A 5,000-square-foot annex at John F. Kennedy…

78 FR 65195 - Airworthiness Directives; MD Helicopters, Inc. (MDHI) Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-31

... certificate and must be entered into the aircraft maintenance records showing compliance with this AD in... requires a daily check of the position of each bolt, a daily check and a repetitive inspection for a gap in... Durbin, Aerospace Engineer, FAA, Los Angeles Aircraft Certification Office, Airframe Branch, ANM-120L...

Producibility Analysis of the Alternative Antitank Airframe Configuration (AATAC) Flex-Wing

DTIC Science & Technology

1988-06-01

3 II. PRODUCTIONIPRODUCIBILITY CONSIDERATIONS ...................... 4 A. High Rage Manufacturing Issues...41 7. Hydroform process showing (1) blank in place, no pressure in cavity, (2) press closed and cavity pressurized, (3) ram... hydroforming and Guerin processes ..... 42 viI LIST OF TABLES Table Page 1. Comparison of Candidate Alloys ................................. 6 2. AATAC Wing

Academic Airframe Icing Perspective

NASA Technical Reports Server (NTRS)

Bragg, Mike; Rothmayer, Alric; Thompson, David

2009-01-01

2-D ice accretion and aerodynamics reasonably well understood for engineering applications To significantly improve our current capabilities we need to understand 3-D: a) Important ice accretion physics and modeling not well understood in 3-D; and b) Aerodynamics unsteady and 3-D especially near stall. Larger systems issues important and require multidisciplinary team approach

78 FR 69456 - Notice To Reinstate a Previously Approved Information Collection; Comment Request

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-19

... incident occurred on approach, takeoff, or within 3 miles of an airport); ``flight crew member 1... requests information concerning the location and date and time of the accident or incident, the phase of... last inspection, total time on airframe, type of fire extinguishing system, type of reciprocating fuel...

78 FR 53630 - Airworthiness Directives; Alexander Schleicher GmbH & Co. Segelflugzeugbau Sailplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-08-30

... rod for conformity following Alexander Schleicher Automatischer H[ouml]henruderanschlu[beta] (English... Manual (CAM) 18, Maintenance, Repair, And Alteration, Of Airframes, Powerplants, Propellers, And...--and-- Guidance--Library/rgccab.nsf/0/41df1277f2dc7e0e86257bcf005112bf/ $FILE/CAM--18--1959.pdf...

14 CFR 91.411 - Altimeter system and altitude reporting equipment tests and inspections.

Code of Federal Regulations, 2012 CFR

2012-01-01

... reporting equipment tests and inspections. (a) No person may operate an airplane, or helicopter, in... conducted by— (1) The manufacturer of the airplane, or helicopter, on which the tests and inspections are to... airframe rating appropriate to the airplane, or helicopter, to be tested; or (3) A certificated mechanic...

14 CFR 91.411 - Altimeter system and altitude reporting equipment tests and inspections.

Code of Federal Regulations, 2013 CFR

2013-01-01

... reporting equipment tests and inspections. (a) No person may operate an airplane, or helicopter, in... conducted by— (1) The manufacturer of the airplane, or helicopter, on which the tests and inspections are to... airframe rating appropriate to the airplane, or helicopter, to be tested; or (3) A certificated mechanic...

14 CFR 91.411 - Altimeter system and altitude reporting equipment tests and inspections.

Code of Federal Regulations, 2014 CFR

2014-01-01

... reporting equipment tests and inspections. (a) No person may operate an airplane, or helicopter, in... conducted by— (1) The manufacturer of the airplane, or helicopter, on which the tests and inspections are to... airframe rating appropriate to the airplane, or helicopter, to be tested; or (3) A certificated mechanic...

14 CFR 91.411 - Altimeter system and altitude reporting equipment tests and inspections.

Code of Federal Regulations, 2011 CFR

2011-01-01

... reporting equipment tests and inspections. (a) No person may operate an airplane, or helicopter, in... conducted by— (1) The manufacturer of the airplane, or helicopter, on which the tests and inspections are to... airframe rating appropriate to the airplane, or helicopter, to be tested; or (3) A certificated mechanic...

14 CFR 91.411 - Altimeter system and altitude reporting equipment tests and inspections.

Code of Federal Regulations, 2010 CFR

2010-01-01

... reporting equipment tests and inspections. (a) No person may operate an airplane, or helicopter, in... conducted by— (1) The manufacturer of the airplane, or helicopter, on which the tests and inspections are to... airframe rating appropriate to the airplane, or helicopter, to be tested; or (3) A certificated mechanic...

Low Speed Rot or/Fuselage Interactional Aerodynamics

NASA Technical Reports Server (NTRS)

Barnwell, Richard W.; Prichard, Devon S.

2003-01-01

This report presents work performed under a Cooperative Research Agreement between Virginia Tech and the NASA Langley Research Center. The work involved development of computational techniques for modeling helicopter rotor/airframe aerodynamic interaction. A brief overview of the problem is presented, the modeling techniques are described, and selected example calculations are briefly discussed.

Airframe materials for HSR

NASA Technical Reports Server (NTRS)

Bales, Thomas T.

1992-01-01

Vugraphs are presented to show the use of refractory materials for the skin of the High speed Civil Transport (HSCT). Examples are given of skin temperature ranges, failure mode weight distribution, tensile properties as a function of temperature, and components to be constructed from composite materials. The responsibilities of various aircraft companies for specific aircraft components are defined.

78 FR 65235 - Special Conditions: Learjet Inc., Model LJ-200-1A10 Airplane; Crashworthiness, Emergency Landing...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-31

.... These features are associated with a hybrid construction that uses both composite and metallic materials... wing consists of resin transfer infusion (RTI) skins with composite spars and metallic ribs. The empennage consists of composite sandwich skins with metallic spars and ribs. The airframe has a sandwich...

76 FR 21820 - Airworthiness Directives; Bombardier, Inc. Model DHC-8-400 Series Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-19

... Engineer, Airframe and Mechanical Systems Branch, ANE-171, FAA, New York Aircraft Certification Office... incorporation of a new maintenance task for the MLG stabilizer extension springs. You may obtain further... Temporary Revision MRB-45, dated October 6, 2009 to Section 1-32, Systems/Powerplant Maintenance Program of...

14 CFR 43.7 - Persons authorized to approve aircraft, airframes, aircraft engines, propellers, appliances, or...

Code of Federal Regulations, 2010 CFR

2010-01-01

... data approved by the Administrator. (e) The holder of an air carrier operating certificate or an... holder of a repairman certificate (light-sport aircraft) with a maintenance rating may approve an aircraft issued a special airworthiness certificate in light-sport category for return to service, as...

Propulsion and Power Generation Capabilities of a Dense Plasma Focus (DPF) Fusion System for Future Military Aerospace Vehicles (POSTPRINT)

DTIC Science & Technology

2005-10-06

The objective of this study was to perform a parametric evaluation of the performance and interface characteristics of a dense plasma focus (DPF...dense plasma focus (DPF) fusion power and propulsion technology, with advanced waverider-like airframe configurations utilizing air-breathing MHD

Technology transfer and other public policy implications of multi-national arrangements for the production of commercial airframes

NASA Technical Reports Server (NTRS)

Gellman, A. J.; Price, J. P.

1978-01-01

A study to examine the question of technology transfer through international arrangements for production of commercial transport aircraft is presented. The likelihood of such transfer under various representative conditions was determined and an understanding of the economic motivations for, effects of, joint venture arrangements was developed. Relevant public policy implications were also assessed. Multinational consortia with U.S. participation were focused upon because they generate the full range of pertinent public issues (including especially technology transfer), and also because of recognized trends toward such arrangements. An extensive search and analysis of existing literature to identify the key issues, and in-person interviews with executives of U.S. and European commercial airframe producers was reviewed. Distinctions were drawn among product-embodied, process, and management technologies in terms of their relative possibilities of transfer and the significance of such transfer. Also included are observations on related issues such as the implications of U.S. antitrust policy with respect to the formation of consortia and the competitive viability of the U.S. aircraft manufacturing industry.

ATD Occupant Responses from Three Full-Scale General Aviation Crash Tests

NASA Technical Reports Server (NTRS)

Littell, Justin D.; Annett, Martin S.

2016-01-01

During the summer of 2015, three Cessna 172 General Aviation (GA) aircraft were crash tested at the Landing and Impact Research (LandIR) Facility at NASA Langley Research Center (LaRC). Three different crash scenarios were represented. The first test simulated a flare-to-stall emergency or hard landing onto a rigid surface such as a road or runway. The second test simulated a controlled flight into terrain with a nose down pitch of the aircraft, and the third test simulated a controlled flight into terrain with an attempt to unsuccessfully recover the aircraft immediately prior to impact, resulting in a tail strike condition. An on-board data acquisition system (DAS) captured 64 channels of airframe acceleration, along with accelerations and loads in two onboard Hybrid II 50th percentile Anthropomorphic Test Devices (ATDs) representing the pilot and copilot. Each of the three tests contained different airframe loading conditions and different types of restraints for both the pilot and co-pilot ATDs. The results show large differences in occupant response and restraint performance with varying likelihoods of occupant injury.

A comparative framework for maneuverability and gust tolerance of aerial microsystems

NASA Astrophysics Data System (ADS)

Campbell, Renee

Aerial microsystems have the potential of navigating low-altitude, cluttered environments such as urban corridors and building interiors. Reliable systems require both agility and tolerance to gusts. While many platform designs are under development, no framework currently exists to quantitatively assess these inherent bare airframe characteristics which are independent of closed loop controllers. This research develops a method to quantify the maneuverability and gust tolerance of vehicles using reachability and disturbance sensitivity sets. The method is applied to a stable flybar helicopter and an unstable flybarless helicopter, whose state space models were formed through system identification. Model-based static H∞ controllers were also implemented on the vehicles and tested in the lab using fan-generated gusts. It is shown that the flybar restricts the bare airframe's ability to maneuver in translational velocity directions. As such, the flybarless helicopter proved more maneuverable and gust tolerant than the flybar helicopter. This approach was specifically applied here to compare stable and unstable helicopter platforms; however, the framework may be used to assess a broad range of aerial microsystems.

Testing Installed Propulsion for Shielded Exhaust Configurations

NASA Technical Reports Server (NTRS)

Bridges, James E.; Podboy, Gary G.; Brown, Clifford A.

2016-01-01

Jet-surface interaction (JSI) can be a significant factor in the exhaust noise of installed propulsion systems. Tests to further the understanding and prediction of the acoustic impacts of JSI have been described. While there were many objectives for the test, the overall objective was to prepare for a future test validating the design of a low-noise, lowboom supersonic commercial airliner. In this paper we explore design requirements for a partial aircraft model to be used in subscale acoustic testing, especially focusing on the amount of aircraft body that must be included to produce the acoustic environment between propulsion exhaust system and observer. We document the dual-stream jets, both nozzle and flow conditions, which were tested to extend JSI acoustic modeling from simple singlestream jets to realistic dual-stream exhaust nozzles. Sample observations are provided of changes to far-field sound as surface geometry and flow conditions were varied. Initial measurements are presented for integrating the propulsion on the airframe for a supersonic airliner with simulated airframe geometries and nozzles. Acoustic impacts of installation were modest, resulting in variations of less than 3 EPNdB in most configurations.

Jet-Surface Interaction Noise from High-Aspect Ratio Nozzles: Test Summary

NASA Technical Reports Server (NTRS)

Brown, Clifford; Podboy, Gary

2017-01-01

Noise and flow data have been acquired for a 16:1 aspect ratio rectangular nozzle exhausting near a simple surface at the NASA Glenn Research Center as part of an ongoing effort to understand, model, and predict the noise produced by current and future concept aircraft employing a tightly integrated engine airframe designs. The particular concept under consideration in this experiment is a blended-wing-body airframe powered by a series of electric fans exhausting through slot nozzle over an aft deck. The exhaust Mach number and surface length were parametrically varied during the test. Far-field noise data were acquired for all nozzle surface geometries and exhaust flow conditions. Phased-array noise source localization data and in-flow pressure data were also acquired for a subset of the isolated (no surface) and surface configurations; these measurements provide data that have proven useful for modeling the jet-surface interaction noise source and the surface effect on the jet-mixing noise in round jets. A summary of the nozzle surface geometry, flow conditions tested, and data collected are presented.

Application of CART3D to Complex Propulsion-Airframe Integration with Vehicle Sketch Pad

NASA Technical Reports Server (NTRS)

Hahn, Andrew S.

2012-01-01

Vehicle Sketch Pad (VSP) is an easy-to-use modeler used to generate aircraft geometries for use in conceptual design and analysis. It has been used in the past to generate metageometries for aerodynamic analyses ranging from handbook methods to Navier-Stokes computational fluid dynamics (CFD). As desirable as it is to bring high order analyses, such as CFD, into the conceptual design process, this has been difficult and time consuming in practice due to the manual nature of both surface and volume grid generation. Over the last couple of years, VSP has had a major upgrade of its surface triangulation and export capability. This has enhanced its ability to work with Cart3D, an inviscid, three dimensional fluid flow toolset. The combination of VSP and Cart3D allows performing inviscid CFD on complex geometries with relatively high productivity. This paper will illustrate the use of VSP with Cart3D through an example case of a complex propulsion-airframe integration (PAI) of an over-wing nacelle (OWN) airliner configuration.

High-Fidelity Computational Aerodynamics of Multi-Rotor Unmanned Aerial Vehicles

NASA Technical Reports Server (NTRS)

Ventura Diaz, Patricia; Yoon, Seokkwan

2018-01-01

High-fidelity Computational Fluid Dynamics (CFD) simulations have been carried out for several multi-rotor Unmanned Aerial Vehicles (UAVs). Three vehicles have been studied: the classic quadcopter DJI Phantom 3, an unconventional quadcopter specialized for forward flight, the SUI Endurance, and an innovative concept for Urban Air Mobility (UAM), the Elytron 4S UAV. The three-dimensional unsteady Navier-Stokes equations are solved on overset grids using high-order accurate schemes, dual-time stepping, and a hybrid turbulence model. The DJI Phantom 3 is simulated with different rotors and with both a simplified airframe and the real airframe including landing gear and a camera. The effects of weather are studied for the DJI Phantom 3 quadcopter in hover. The SUI En- durance original design is compared in forward flight to a new configuration conceived by the authors, the hybrid configuration, which gives a large improvement in forward thrust. The Elytron 4S UAV is simulated in helicopter mode and in airplane mode. Understanding the complex flows in multi-rotor vehicles will help design quieter, safer, and more efficient future drones and UAM vehicles.

Analysis of Aviation Safety Reporting System Incident Data Associated with the Technical Challenges of the Atmospheric Environment Safety Technology Project

NASA Technical Reports Server (NTRS)

Withrow, Colleen A.; Reveley, Mary S.

2014-01-01

This study analyzed aircraft incidents in the NASA Aviation Safety Reporting System (ASRS) that apply to two of the three technical challenges (TCs) in NASA's Aviation Safety Program's Atmospheric Environment Safety Technology Project. The aircraft incidents are related to airframe icing and atmospheric hazards TCs. The study reviewed incidents that listed their primary problem as weather or environment-nonweather between 1994 and 2011 for aircraft defined by Federal Aviation Regulations (FAR) Parts 121, 135, and 91. The study investigated the phases of flight, a variety of anomalies, flight conditions, and incidents by FAR part, along with other categories. The first part of the analysis focused on airframe-icing-related incidents and found 275 incidents out of 3526 weather-related incidents over the 18-yr period. The second portion of the study focused on atmospheric hazards and found 4647 incidents over the same time period. Atmospheric hazards-related incidents included a range of conditions from clear air turbulence and wake vortex, to controlled flight toward terrain, ground encounters, and incursions.

Application of an integrated flight/propulsion control design methodology to a STOVL aircraft

NASA Technical Reports Server (NTRS)

Garg, Sanjay; Mattern, Duane L.

1991-01-01

Results are presented from the application of an emerging Integrated Flight/Propulsion Control (IFPC) design methodology to a Short Take Off and Vertical Landing (STOVL) aircraft in transition flight. The steps in the methodology consist of designing command shaping prefilters to provide the overall desired response to pilot command inputs. A previously designed centralized controller is first validated for the integrated airframe/engine plant used. This integrated plant is derived from a different model of the engine subsystem than the one used for the centralized controller design. The centralized controller is then partitioned in a decentralized, hierarchical structure comprising of airframe lateral and longitudinal subcontrollers and an engine subcontroller. Command shaping prefilters from the pilot control effector inputs are then designed and time histories of the closed loop IFPC system response to simulated pilot commands are compared to desired responses based on handling qualities requirements. Finally, the propulsion system safety and nonlinear limited protection logic is wrapped around the engine subcontroller and the response of the closed loop integrated system is evaluated for transients that encounter the propulsion surge margin limit.

Thermal design and analysis of a hydrogen-burning wind tunnel model of an airframe-integrated scramjet

NASA Technical Reports Server (NTRS)

Guy, R. W.; Mueller, J. N.; Pinckney, S. Z.; Lee, L. P.

1976-01-01

An aerodynamic model of a hydrogen burning, airframe integrated scramjet engine has been designed, fabricated, and instrumented. This model is to be tested in an electric arc heated wind tunnel at an altitude of 35.39 km (116,094 ft.) but with an inlet Mach number of 6 simulating precompression on an aircraft undersurface. The scramjet model is constructed from oxygen free, high conductivity copper and is a heat sink design except for water cooling in some critical locations. The model is instrumented for pressure, surface temperature, heat transfer rate, and thrust measurements. Calculated flow properties, heat transfer rates, and surface temperature distributions along the various engine components are included for the conditions stated above. For some components, estimates of thermal strain are presented which indicate significant reductions in plastic strain by selective cooling of the model. These results show that the 100 thermal cycle life of the engine was met with minimum distortion while staying within the 2669 N (600 lbf) engine weight limitation and while cooling the engine only in critical locations.

Turbine Powered Simulator Calibration and Testing for Hybrid Wing Body Powered Airframe Integration

NASA Technical Reports Server (NTRS)

Shea, Patrick R.; Flamm, Jeffrey D.; Long, Kurtis R.; James, Kevin D.; Tompkins, Daniel M.; Beyar, Michael D.

2016-01-01

Propulsion airframe integration testing on a 5.75% scale hybrid wing body model us- ing turbine powered simulators was completed at the National Full-Scale Aerodynamics Complex 40- by 80-foot test section. Four rear control surface con gurations including a no control surface de ection con guration were tested with the turbine powered simulator units to investigate how the jet exhaust in uenced the control surface performance as re- lated to the resultant forces and moments on the model. Compared to ow-through nacelle testing on the same hybrid wing body model, the control surface e ectiveness was found to increase with the turbine powered simulator units operating. This was true for pitching moment, lift, and drag although pitching moment was the parameter of greatest interest for this project. With the turbine powered simulator units operating, the model pitching moment was seen to increase when compared to the ow-through nacelle con guration indicating that the center elevon and vertical tail control authority increased with the jet exhaust from the turbine powered simulator units.

Development and Utility of a Piloted Flight Simulator for Icing Effects Training

NASA Technical Reports Server (NTRS)

Ratvasky, Thomas P.; Ranaudo, Richard J.; Barnhart, Billy P.; Dickes, Edward G.; Gingras, David R.

2003-01-01

A piloted flight simulator called the Ice Contamination Effects Flight Training Device (ICEFTD), which uses low cost desktop components and a generic cockpit replication is being developed. The purpose of this device is to demonstrate the effectiveness of its use for training pilots to recognize and recover from aircraft handling anomalies that result from airframe ice formations. High-fidelity flight simulation models for various baseline (non-iced) and iced configurations were developed from wind tunnel tests of a subscale DeHavilland DHC-6 Twin Otter aircraft model. These simulation models were validated with flight test data from the NASA Twin Otter Icing Research Aircraft, which included the effects of ice on wing and tail stall characteristics. These simulation models are being implemented into an ICEFTD that will provide representative aircraft characteristics due to airframe icing. Scenario-based exercises are being constructed to give an operational-flavor to the simulation. Training pilots will learn to recognize iced aircraft characteristics from the baseline, and will practice and apply appropriate recovery procedures to a handling event.

Testing Installed Propulsion For Shielded Exhaust Configurations

NASA Technical Reports Server (NTRS)

Bridges, James; Podboy, Gary G.; Brown, Clifford A.

2016-01-01

Jet-surface interaction (JSI) can be a significant factor in the exhaust noise of installed propulsion. Tests to further understanding and prediction of the acoustic impacts of JSI have been described. While there were many objectives for the NASA JSI1044 test, the overall objective was to prepare for a 2016 test validating the design of a low-noise, low-boom supersonic commercial airliner. In this paper we explore design requirements for a partial aircraft model to be used in subscale acoustic testing, especially focusing on the amount of shielding surface that must be provided to simulate the acoustic environment between propulsion exhaust system and observer. We document the dual-stream jets, both nozzle and flow conditions, which were tested to extend JSI acoustic modeling from simple single-stream jets to realistic dual-stream exhaust nozzles. Examples of observations found as surface geometry and flow conditions were varied were provided. And we have presented initial measurements of the installation impacts of integrating the propulsion on the airframe for a supersonic airliner with realistic airframe geometries and nozzles.

Development of a SMA-Based Slat-Cove Filler for Reduction of Aeroacoustic Noise Associated With Transport-Class Aircraft Wings

NASA Technical Reports Server (NTRS)

Turner, Travis L.; Kidd, Reggie T.; Hartl, Darren J.; Scholten, William D.

2013-01-01

Airframe noise is a significant part of the overall noise produced by typical, transport-class aircraft during the approach and landing phases of flight. Leading-edge slat noise is a prominent source of airframe noise. The concept of a slat-cove filler was proposed in previous work as an effective means of mitigating slat noise. Bench-top models were deployed at 75% scale to study the feasibility of producing a functioning slat-cove filler. Initial results from several concepts led to a more-focused effort investigating a deformable structure based upon pseudoelastic SMA materials. The structure stows in the cavity between the slat and main wing during cruise and deploys simultaneously with the slat to guide the aerodynamic flow suitably for low noise. A qualitative parametric study of SMA-enabled, slat-cove filler designs was performed on the bench-top. Computational models were developed and analyses were performed to assess the displacement response under representative aerodynamic load. The bench-top and computational results provide significant insight into design trades and an optimal design.

Bibliography on propulsion airframe integration technologies for high-speed civil transport applications, 1980-1991

NASA Technical Reports Server (NTRS)

Anderson, David J.; Mizukami, Masashi

1993-01-01

NASA has initiated the High Speed Research (HSR) program with the goal to develop technologies for a new generation, economically viable, environmentally acceptable, supersonic transport (SST) called the High Speed Civil Transport (HSCT). A significant part of this effort is expected to be in multidisciplinary systems integration, such as in propulsion airframe integration (PAI). In order to assimilate the knowledge database on PAI for SST type aircraft, a bibliography on this subject was compiled. The bibliography with over 1200 entries, full abstracts, and indexes. Related topics are also covered, such as the following: engine inlets, engine cycles, nozzles, existing supersonic cruise aircraft, noise issues, computational fluid dynamics, aerodynamics, and external interference. All identified documents from 1980 through early 1991 are included; this covers the latter part of the NASA Supersonic Cruise Research (SCR) program and the beginnings of the HSR program. In addition, some pre-1980 documents of significant merit or reference value are also included. The references were retrieved via a computerized literature search using the NASA RECON database system.

Aviation Trends Related to Atmospheric Environment Safety Technologies Project Technical Challenges

NASA Technical Reports Server (NTRS)

Reveley, Mary S.; Withrow, Colleen A.; Barr, Lawrence C.; Evans, Joni K.; Leone, Karen M.; Jones, Sharon M.

2014-01-01

Current and future aviation safety trends related to the National Aeronautics and Space Administration's Atmospheric Environment Safety Technologies Project's three technical challenges (engine icing characterization and simulation capability; airframe icing simulation and engineering tool capability; and atmospheric hazard sensing and mitigation technology capability) were assessed by examining the National Transportation Safety Board (NTSB) accident database (1989 to 2008), incidents from the Federal Aviation Administration (FAA) accident/incident database (1989 to 2006), and literature from various industry and government sources. The accident and incident data were examined for events involving fixed-wing airplanes operating under Federal Aviation Regulation (FAR) Parts 121, 135, and 91 for atmospheric conditions related to airframe icing, ice-crystal engine icing, turbulence, clear air turbulence, wake vortex, lightning, and low visibility (fog, low ceiling, clouds, precipitation, and low lighting). Five future aviation safety risk areas associated with the three AEST technical challenges were identified after an exhaustive survey of a variety of sources and include: approach and landing accident reduction, icing/ice detection, loss of control in flight, super density operations, and runway safety.

Active transmission isolation/rotor loads measurement system

NASA Technical Reports Server (NTRS)

Kenigsberg, I. J.; Defelice, J. J.

1973-01-01

Modifications were incorporated into a helicopter active transmission isolation system to provide the capability of utilizing the system as a rotor force measuring device. These included; (1) isolator redesign to improve operation and minimize friction, (2) installation of pressure transducers in each isolator, and (3) load cells in series with each torque restraint link. Full scale vibration tests performed during this study on a CH-53A helicopter airframe verified that these modifications do not degrade the systems wide band isolation characteristics. Bench tests performed on each isolator unit indicated that steady and transient loads can be measured to within 1 percent of applied load. Individual isolator vibratory load measurement accuracy was determined to be 4 percent. Load measurement accuracy was found to be independent of variations in all basic isolator operating characteristics. Full scale system load calibration tests on the CH-53A airframe established the feasibility of simultaneously providing wide band vibration isolation and accurate measurement of rotor loads. Principal rotor loads (lift, propulsive force, and torque) were measured to within 2 percent of applied load.

Reliability-Based Design Optimization of a Composite Airframe Component

NASA Technical Reports Server (NTRS)

Patnaik, Surya N.; Pai, Shantaram S.; Coroneos, Rula M.

2009-01-01

A stochastic design optimization methodology (SDO) has been developed to design components of an airframe structure that can be made of metallic and composite materials. The design is obtained as a function of the risk level, or reliability, p. The design method treats uncertainties in load, strength, and material properties as distribution functions, which are defined with mean values and standard deviations. A design constraint or a failure mode is specified as a function of reliability p. Solution to stochastic optimization yields the weight of a structure as a function of reliability p. Optimum weight versus reliability p traced out an inverted-S-shaped graph. The center of the inverted-S graph corresponded to 50 percent (p = 0.5) probability of success. A heavy design with weight approaching infinity could be produced for a near-zero rate of failure that corresponds to unity for reliability p (or p = 1). Weight can be reduced to a small value for the most failure-prone design with a reliability that approaches zero (p = 0). Reliability can be changed for different components of an airframe structure. For example, the landing gear can be designed for a very high reliability, whereas it can be reduced to a small extent for a raked wingtip. The SDO capability is obtained by combining three codes: (1) The MSC/Nastran code was the deterministic analysis tool, (2) The fast probabilistic integrator, or the FPI module of the NESSUS software, was the probabilistic calculator, and (3) NASA Glenn Research Center s optimization testbed CometBoards became the optimizer. The SDO capability requires a finite element structural model, a material model, a load model, and a design model. The stochastic optimization concept is illustrated considering an academic example and a real-life raked wingtip structure of the Boeing 767-400 extended range airliner made of metallic and composite materials.

High speed commercial transport fuels considerations and research needs

NASA Technical Reports Server (NTRS)

Lee, C. M.; Niedzwiecki, R. W.

1989-01-01

NASA is currently evaluating the potential of incorporating High Speed Civil Transport (HSCT) aircraft in the commercial fleet in the beginning of the 21st century. NASA sponsored HSCT enabling studies currently underway with airframers and engine manufacturers, are addressing a broad range of technical, environmental, economic, and related issues. Supersonic cruise speeds for these aircraft were originally focused in the Mach 2 to 5 range. At these flight speeds, both jet fuels and liquid methane were considered potential fuel candidates. For the year 2000 to 2010, cruise Mach numbers of 2 to 3+ are projected for aircraft fuel with thermally stable liquid jet fuels. For 2015 and beyond, liquid methane fueled aircraft cruising at Mach numbers of 4+ may be viable candidates. Operation at supersonic speeds will be much more severe than those encountered at subsonic flight. One of the most critical problems is the potential deterioration of the fuel due to the high temperature environment. HSCT fuels will not only be required to provide the energy necessary for flight, but will also be subject to aerodynamic heating and, will be required to serve as the primary heat sink for cooling the engine and airframe. To define fuel problems for high speed flight, a fuels workshop was conducted at NASA Lewis Research Center. The purpose of the workshop was to gather experts on aviation fuels, airframe fuel systems, airport infrastructure, and combustion systems to discuss high speed fuel alternatives, fuel supply scenarios, increased thermal stability approaches and measurements, safety considerations, and to provide directional guidance for future R and D efforts. Subsequent follow-up studies defined airport infrastructure impacts of high speed fuel candidates. The results of these activities are summarized. In addition, an initial case study using modified in-house refinery simulation model Gordian code (1) is briefly discussed. This code can be used to simulate different types of refineries, emphasizing jet fuel production and relative cost factors.

Reducing Propulsion Airframe Aeroacoustic Interactions With Uniquely Tailored Chevrons: 3. Jet-Flap Interaction

NASA Technical Reports Server (NTRS)

Thomas, Russ H.; Mengle, Vinod G.; Brunsniak, Leon; Elkoby, Ronen

2006-01-01

Propulsion airframe aeroacoustic (PAA) interactions, resulting from the integration of engine and airframe, lead to azimuthal asymmetries in the flow/acoustic field, e.g., due to the interaction between the exhaust jet flow and the pylon, the wing and its high-lift devices, such as, flaps and flaperons. In the first two parts of this series we have presented experimental results which show that isolated and installed nozzles with azimuthally varying chevrons (AVCs) can reduce noise more than conventional chevrons when integrated with a pylon and a wing with flaps at take-off conditions. In this paper, we present model-scale experimental results for the reduction of jet-flap interaction noise source due to these AVCs and document the PAA installation effects (difference in noise between installed and isolated nozzle configurations) at both approach and take-off conditions. It is found that the installation effects of both types of chevron nozzles, AVCs and conventional, are reversed at approach and take-off, in that there is more installed noise reduction at approach and less at take-off compared to that of the isolated nozzles. Moreover, certain AVCs give larger total installed noise benefits at both conditions compared to conventional chevrons. Phased microphone array results show that at approach conditions (large flap deflection, low jet speed and low ambient Mach number), chevrons gain more noise benefit from reducing jetflap interaction noise than they do from quieting the jet plume noise source which is already weak at these low jet speeds. In contrast, at take-off (small flap deflection, high jet speed and high ambient Mach number) chevrons reduce the dominant jet plume noise better than the reduction they create in jet-flap interaction noise source. In addition, fan AVCs with enhanced mixing near the pylon are found to reduce jet-flap interaction noise better than conventional chevrons at take-off.

Airframe Noise Results from the QTD II Flight Test Program

NASA Technical Reports Server (NTRS)

Elkoby, Ronen; Brusniak, Leon; Stoker, Robert W.; Khorrami, Mehdi R.; Abeysinghe, Amal; Moe, Jefferey W.

2007-01-01

With continued growth in air travel, sensitivity to community noise intensifies and materializes in the form of increased monitoring, regulations, and restrictions. Accordingly, realization of quieter aircraft is imperative, albeit only achievable with reduction of both engine and airframe components of total aircraft noise. Model-scale airframe noise testing has aided in this pursuit; however, the results are somewhat limited due to lack of fidelity of model hardware, particularly in simulating full-scale landing gear. Moreover, simulation of true in-flight conditions is non-trivial if not infeasible. This paper reports on an investigation of full-scale landing gear noise measured as part of the 2005 Quiet Technology Demonstrator 2 (QTD2) flight test program. Conventional Boeing 777-300ER main landing gear were tested, along with two noise reduction concepts, namely a toboggan fairing and gear alignment with the local flow, both of which were down-selected from various other noise reduction devices evaluated in model-scale testing at Virginia Tech. The full-scale toboggan fairings were designed by Goodrich Aerostructures as add-on devices allowing for complete retraction of the main gear. The baseline-conventional gear, faired gear, and aligned gear were all evaluated with the high-lift system in the retracted position and deployed at various flap settings, all at engine idle power setting. Measurements were taken with flyover community noise microphones and a large aperture acoustic phased array, yielding far-field spectra, and localized sources (beamform maps). The results were utilized to evaluate qualitatively and quantitatively the merit of each noise reduction concept. Complete similarity between model-scale and full-scale noise reduction levels was not found and requires further investigation. Far-field spectra exhibited no noise reduction for both concepts across all angles and frequencies. Phased array beamform maps show inconclusive evidence of noise reduction at selective frequencies (1500 to 3000 Hz) but are otherwise in general agreement with the far-field spectra results (within measurement uncertainty).