Science.gov

Sample records for al ruido industrial

  1. 18.5% efficient AlOx/SiNy rear passivated industrial multicrystalline silicon solar cells

    NASA Astrophysics Data System (ADS)

    Qiao, Qi; Lu, Hongyan; Ge, Jian; Xi, Xi; Chen, Rulong; Yang, Jian; Zhu, Jingbing; Shi, Zhengrong; Chu, Junhao

    2014-06-01

    Due to the trend toward thinner and higher efficient crystalline silicon solar cells, excellent rear surface passivation and internal optical reflectance have become more and more important. Aluminum oxide (AlOx) capped with silicon nitride (SiNy), which is considered as one of the most promising candidates to achieve superior rear passivation and internal reflectance, has to date been mostly used for the rear side of p-type monocrystalline silicon (mono-Si) solar cells. In this paper, we have optimized rear AlOx/SiNy stacks deposited by industrial plasma enhanced chemical vapor deposition (PECVD) for multicrystalline silicon (mc-Si) passivated emitter and rear cells (PERC). Sufficient passivation activation effect from industrial fast-firing process and SiNy deposition process have been demonstrated, so the samples were not subjected to additional thermal treatment process in the cell fabrication flow. For rear AlOx/SiNy stack, it is shown that when PECVD AlOx is thicker than 40 nm, apparent blisters in fired AlOx deteriorate the cell performance, and the appropriate SiNy capping is N-rich SiNy with thickness of at least 180 nm. After process optimization with the least additional process steps, independently confirmed efficiency of 18.5% for Pluto-PERC with PECVD AlOx/SiNy rear passivation on standard 156 mm × 156 mm p-type mc-Si wafers has been achieved.

  2. ESEEM of industrial quartz powders: insights into crystal chemistry of Al defects

    NASA Astrophysics Data System (ADS)

    Romanelli, Maurizio; Di Benedetto, Francesco; Bartali, Laura; Innocenti, Massimo; Fornaciai, Gabriele; Montegrossi, Giordano; Pardi, Luca A.; Zoleo, Alfonso; Capacci, Fabio

    2012-06-01

    A set of raw industrial materials, that is, pure quartz and quartz-rich mixtures, were investigated through electron paramagnetic resonance and electron spin echo-envelope modulation spectroscopies, with the aim of evaluating the effective role played by defect centres and of assessing whether they can be used to monitor changes in the physical properties of quartz powders with reference to their health effects. The obtained results point to two interactions of the Al defect centres with H+, hosted in sites within the channels parallel and perpendicular to the c axis of quartz, respectively. These two Al/H+ (hAl) centres exhibit a weak chemical bond, and their relative amounts appear to be modified/controlled by the thermo-mechanical processes underwent by powders. Indeed, a mechanically promoted inter-conversion between the two kinds of site is suggested. As a consequence, the hAl centres are effective in monitoring even modest activations of powders, through thermal or mechanical processes, and they are also supposed to play a specific, relevant role in quartz reactivity during the considered industrial processes.

  3. Industry

    SciTech Connect

    Bernstein, Lenny; Roy, Joyashree; Delhotal, K. Casey; Harnisch, Jochen; Matsuhashi, Ryuji; Price, Lynn; Tanaka, Kanako; Worrell, Ernst; Yamba, Francis; Fengqi, Zhou; de la Rue du Can, Stephane; Gielen, Dolf; Joosen, Suzanne; Konar, Manaswita; Matysek, Anna; Miner, Reid; Okazaki, Teruo; Sanders, Johan; Sheinbaum Parado, Claudia

    2007-12-01

    This chapter addresses past, ongoing, and short (to 2010) and medium-term (to 2030) future actions that can be taken to mitigate GHG emissions from the manufacturing and process industries. Globally, and in most countries, CO{sub 2} accounts for more than 90% of CO{sub 2}-eq GHG emissions from the industrial sector (Price et al., 2006; US EPA, 2006b). These CO{sub 2} emissions arise from three sources: (1) the use of fossil fuels for energy, either directly by industry for heat and power generation or indirectly in the generation of purchased electricity and steam; (2) non-energy uses of fossil fuels in chemical processing and metal smelting; and (3) non-fossil fuel sources, for example cement and lime manufacture. Industrial processes also emit other GHGs, e.g.: (1) Nitrous oxide (N{sub 2}O) is emitted as a byproduct of adipic acid, nitric acid and caprolactam production; (2) HFC-23 is emitted as a byproduct of HCFC-22 production, a refrigerant, and also used in fluoroplastics manufacture; (3) Perfluorocarbons (PFCs) are emitted as byproducts of aluminium smelting and in semiconductor manufacture; (4) Sulphur hexafluoride (SF{sub 6}) is emitted in the manufacture, use and, decommissioning of gas insulated electrical switchgear, during the production of flat screen panels and semiconductors, from magnesium die casting and other industrial applications; (5) Methane (CH{sub 4}) is emitted as a byproduct of some chemical processes; and (6) CH{sub 4} and N{sub 2}O can be emitted by food industry waste streams. Many GHG emission mitigation options have been developed for the industrial sector. They fall into three categories: operating procedures, sector-wide technologies and process-specific technologies. A sampling of these options is discussed in Sections 7.2-7.4. The short- and medium-term potential for and cost of all classes of options are discussed in Section 7.5, barriers to the application of these options are addressed in Section 7.6 and the implication of

  4. Characteristics of a multicomponent Nb-Ti-Al alloy via industrial-scale practice

    SciTech Connect

    Sikka, V.K.; Loria, E.A.

    1997-05-01

    Within the spectrum of advanced intermetallic materials, an alloy containing 44Nb-35Ti-6Al-5Cr-8V-1W-0.5Mo-0.3Hf (at. %) was investigated in the industrial-scale produced condition. The alloy was tensile tested in air from room temperature to 1,000 C and in vacuum at 750 and 850 C. Results of this study have shown that the alloy can be commercially produced and has adequate ductility for its secondary processing even at an oxygen level of 1,160 wppm. The alloy has room temperature ductility of 16% and superplastic elongation of 244% at 1,000 C. This alloy shows low intermediate temperature (600--850 C) ductility when tested in air. The vacuum testing revealed that the low ductility is associated within oxygen embrittlement phenomenon. It is expected that such an embrittlement can be taken care of by an oxidation resistant coating. The alloy also possesses superior strength to similar alloys in this class. Results of this investigation suggest a strong potential for consideration of this alloy to exceed the useful temperature range of nickel-base superalloys.

  5. CWPO of 4-CP and industrial wastewater with Al-Fe pillared clays.

    PubMed

    Molina, C B; Zazo, J A; Casas, J A; Rodriguez, J J

    2010-01-01

    Catalysts based on pillared clays with Al-Fe have been synthesised from a commercial bentonite and tested for catalytic wet peroxide oxidation (CWPO) of aqueous 4-Chlorophenol (4-CP) solution and industrial wastewater from cosmetics manufacture. The effect of the synthesis procedure, the iron load and reaction temperature on the catalytic activity was studied using 4-CP as target compound. A lower temperature in the preparation of the pillaring solution, as well as a higher Fe load, gave rise to a higher catalytic activity, but also a higher leaching of the active phase. The best catalyst, in terms of catalytic activity, was also tested for treating cosmetic wastewater by CWPO. Experiments were carried out at 90 degrees C and atmospheric pressure and the influence of Fe load, catalyst concentration and H(2)O(2)/COD ratio (between 0.5 and 2 times the stoichiometric ratio) were analysed. Higher values of these parameters favour COD reduction. The Fe leaching in all cases was lower than 1.2 mg/L, indicating that these catalysts have a high stability under these experimental conditions. PMID:20389016

  6. Oxide Dispersion Strengthened Fe(sub 3)Al-Based Alloy Tubes: Application Specific Development for the Power Generation Industry

    SciTech Connect

    Kad, B.K.

    1999-07-01

    A detailed and comprehensive research and development methodology is being prescribed to produce Oxide Dispersion Strengthened (ODS)-Fe3Al thin walled tubes, using powder extrusion methodologies, for eventual use at operating temperatures of up to 1100C in the power generation industry. A particular 'in service application' anomaly of Fe3Al-based alloys is that the environmental resistance is maintained up to 1200C, well beyond where such alloys retain sufficient mechanical strength. Grain boundary creep processes at such high temperatures are anticipated to be the dominant failure mechanism.

  7. Large-area AlN substrates for electronic applications: An industrial perspective

    NASA Astrophysics Data System (ADS)

    Bondokov, Robert T.; Mueller, Stephan G.; Morgan, Kenneth E.; Slack, Glen A.; Schujman, Sandra; Wood, Mark C.; Smart, Joseph A.; Schowalter, Leo J.

    2008-08-01

    We report on the status of the vapor growth of high-quality AlN bulk crystals by the sublimation-recondensation technique for the commercial production of AlN wafers up to 2 in diameter. AlN boules and wafers have been characterized by X-ray Laue backscattering, diffraction, and rocking curves measured in double-axis configuration, demonstrating a full-width at half-maximum (FWHM) of 28 and 32 arcsec for the symmetric and asymmetric rocking curves, respectively. The etch pit density (EPD) for different AlN substrate orientations was found to be less than 10 4 cm -2. Impurity levels have been measured by glow discharge mass-spectrometry (GDMS) and secondary ion mass-spectroscopy (SIMS). The oxygen content as measured by SIMS shows concentrations <10 18 cm -3. Additionally, a high thermal conductivity of ˜270 W/m K has been measured by the flash method. High-quality homoepitaxial and graded AlGaN layers were grown on the on-axis-oriented AlN substrates. The lack of both piezoelectric and spontaneous polarization fields, for nitride heterostructures grown in non-polar directions, has recently created significant interest in high-quality, non-polar nitride substrates to boost the performance of light emitting diodes (LEDs) and laser diodes. Initial epitaxial results on non-polar AlN substrates are presented.

  8. Reduction of CO2 diffuse emissions from the traditional ceramic industry by the addition of Si-Al raw material.

    PubMed

    González, I; Barba-Brioso, C; Campos, P; Romero, A; Galán, E

    2016-09-15

    The fabrication of ceramics can produce the emission of several gases, denominated exhaust gases, and also vapours resulting from firing processes, which usually contain metals and toxic substances affecting the environment and the health of workers. Especially harmful are the diffuse emissions of CO2, fluorine, chlorine and sulphur from the ceramics industry, which, in highly industrialized areas, can suppose an important emission focus of dangerous effects. Concerning CO2, factories that use carbonate-rich raw materials (>30% carbonates) can emit high concentrations of CO2 to the atmosphere. Thus, carbonate reduction or substitution with other raw materials would reduce the emissions. In this contribution, we propose the addition of Al-shales to the carbonated ceramic materials (marls) for CO2 emission reduction, also improving the quality of the products. The employed shales are inexpensive materials of large reserves in SW-Spain. The ceramic bodies prepared with the addition of selected Al-shale to marls in variable proportions resulted in a 40%-65% CO2 emission reduction. In addition, this research underlines at the same time that the use of a low-price raw material can also contribute to obtaining products with higher added value.

  9. Understanding and development of cost-effective industrial aluminum back surface field (Al-BSF) silicon solar cells

    NASA Astrophysics Data System (ADS)

    Chen, Nian

    For the long-term strategy of gradual decarbonization of the world's energy supply, high penetration of PV electricity is critical in the future world energy landscape. In order to achieve this, solar electricity with competitive cost to fossil fuel energy is necessary. To be able to obtain high efficiency solar cells, many advanced cell architectures have been developed commercially by PV industry. However, the fabrication of these cells necessitates complex processing steps and high requirements on semiconductor materials, which make it not as cost-effective as the state-of-the-art conventional Al-BSF structure. In order to keep the cost of PV cell low and improve on the efficiency with fewer processing steps, this thesis work focuses on the understanding of the conventional Al-BSF solar cell structure. The research work therefore, focuses on the (i) design, and modeling of front metal electrodes including the use of multi-bus-bar capable of decreasing the gridline resistance, (ii) fine-line printing and (iii) metal contact co-firing using high belt speed that is not common to the solar industry to achieve ~20% efficient industrial Al-BSF silicon solar cells. In order to achieve the objectives of this thesis work, firstly, the appropriate Al paste was investigated for lowest back surface recombination velocity (BSRV), which gives high open circuit voltage (Voc). Secondly, the impact of emitter sheet resistance on solar cell performance was modeled to determine the optimal sheet resistance, and the uniformity of emitter was also investigated. Thirdly, modeling on the front metal electrodes was carried out to investigate the optimal number of busbars, and determine the optimum number of gridlines and gridline geometries that would result in low series resistance (Rs), high fill factor (FF) and hence high efficiency. Fourthly, the modeled results were experimentally validated through fine-line printing and optimized contact co-firing. By combining each layer to make

  10. Cold-Sprayed Ni-Al2O3 Coatings for Applications in Power Generation Industry

    NASA Astrophysics Data System (ADS)

    Sevillano, F.; Poza, P.; Múnez, C. J.; Vezzù, S.; Rech, S.; Trentin, A.

    2013-06-01

    Cermets coatings are extensively used in energy applications both because of their high wear resistance as required, for example, in components like gas turbine sealants, and because of their specific functionality as required in solar absorbers. So far, high-temperature thermal spraying and physical vapor deposition have traditionally been used to deposit this kind of coatings. In this study, Ni-Al2O3 coatings have been deposited using a Kinetic®3000 cold-spray system starting from Ni and Al2O3 powders blend; five blends have been prepared setting the alumina content in the feedstock to 10, 25, 50, 75, and 90 wt.%. The embedded alumina ranges between a few percent weight up to 16 and 31 wt.%, while the microhardness shows a deep increase from 175 Vickers in the case of pure Ni coatings up to 338 Vickers. The spray and coating growth mechanism have been discussed, with special attention to the fragmentation of the ceramic particles during the impact. Finally, the coating behavior at high temperature was analyzed by oxidation tests performed in air at 520 °C emphasizing a good oxidation resistance that could represent a very promising basis for application in power generation systems.

  11. Methanol Synthesis over Cu/ZnO/Al2O3: The Active Site in Industrial Catalysis

    SciTech Connect

    Behrens, Malte

    2012-03-28

    Unlike homogeneous catalysts, heterogeneous catalysts that have been optimized through decades are typically so complex and hard to characterize that the nature of the catalytically active site is not known. This is one of the main stumbling blocks in developing rational catalyst design strategies in heterogeneous catalysis. We show here how to identify the crucial atomic structure motif for the industrial Cu/ZnO/Al{sub 2}O{sub 3} methanol synthesis catalyst. Using a combination of experimental evidence from bulk-, surface-sensitive and imaging methods collected on real high-performance catalytic systems in combination with DFT calculations. We show that the active site consists of Cu steps peppered with Zn atoms, all stabilized by a series of well defined bulk defects and surface species that need jointly to be present for the system to work.

  12. Oxide-Dispersion-Strengthened Fe3Al-Based Alloy Tubes: Application-Specific Development for the Power Generation Industry

    SciTech Connect

    Kad, BK

    2001-07-20

    A detailed and comprehensive research and development methodology is being prescribed to produce Oxide Dispersion Strengthened (ODS)-Fe{sub 3}Al thin walled tubes, using powder extrusion methodologies, for eventual use at operating temperatures of up to 1100 C in the power generation industry. A particular ''in service application'' anomaly of Fe{sub 3}Al-based alloys is that the environmental resistance is maintained up to 1200 C, well beyond where such alloys retain sufficient mechanical strength. Grain boundary creep processes at such high temperatures are anticipated to be the dominant failure mechanism. Thus, the challenges of this program are manifold: (1) to produce thin walled ODS-Fe{sub 3}Al tubes, employing powder extrusion methodologies, with (2) adequate increased strength for service at operating temperatures, and (3) to mitigate creep failures by enhancing the as-processed grain size in ODS-Fe{sub 3}Al tubes. Our research progress till date has resulted in the successful batch production of typically 8 Ft. lengths of 1-3/8 inch diameter, 1/8 inch wall thickness, ODS-Fe{sub 3}Al tubes via a proprietary single step extrusion consolidation process. The process parameters for such consolidation methodologies have been prescribed and evaluated as being routinely reproducible. Such processing parameters (i.e., extrusion ratios, temperature, can design etc.) were particularly guided by the need to effect post-extrusion recrystallization and grain growth at a sufficiently low temperature, while still meeting the creep requirement at service temperatures. Static recrystallization studies show that elongated grains (with their long axis parallel to the extrusion axis), typically 200-2000 {micro}m in diameter, and several millimeters long can be obtained routinely, at 1200 C. The growth kinetics are affected by the interstitial impurity content in the powder batches. For example complete recrystallization, across the tube wall thickness, is observed for clean

  13. Formation of a ZnO overlayer in industrial Cu/ZnO/Al2 O3 catalysts induced by strong metal-support interactions.

    PubMed

    Lunkenbein, Thomas; Schumann, Julia; Behrens, Malte; Schlögl, Robert; Willinger, Marc G

    2015-04-01

    In industrially relevant Cu/ZnO/Al2 O3 catalysts for methanol synthesis, the strong metal support interaction between Cu and ZnO is known to play a key role. Here we report a detailed chemical transmission electron microscopy study on the nanostructural consequences of the strong metal support interaction in an activated high-performance catalyst. For the first time, clear evidence for the formation of metastable "graphite-like" ZnO layers during reductive activation is provided. The description of this metastable layer might contribute to the understanding of synergistic effects between the components of the Cu/ZnO/Al2 O3 catalysts. PMID:25683230

  14. Evaluation of Thermocompression Heat Pump Performance for American Maize, Decatur, AL [Advanced Industrial Heat Pump Applications and Evaluations

    SciTech Connect

    Eastwood, A.

    1993-06-01

    This work was carried out in two phases: Phase 1, identification of opportunities for heat pumps in industrial applications and Phase 2, evaluation of heat pumps in industrial applications. In Phase 1, pinch analysis was applied to several industrial sites to identify the best opportunities for heat pumping and other forms of heat integration. In Phase 2, more detailed analyses were undertaken, including the evaluation of a heat pump installed as a recommendation of Phase 1.

  15. Volatile organic compounds emission control in industrial pollution source using plasma technology coupled with F-TiO2/γ-Al2O3.

    PubMed

    Zhu, Tao; Chen, Rui; Xia, Ni; Li, Xiaoyang; He, Xianxian; Zhao, Wenjuan; Carr, Tim

    2015-01-01

    Volatile organic compounds' (VOCs) effluents, which come from many industries, are triggering serious environmental problems. As an emerging technology, non-thermal plasma (NTP) technology is a potential technology for VOCs emission control. NTP coupled with F-TiO2/γ-Al2O3 is used for toluene removal from a gaseous influent at normal temperature and atmospheric pressure. NTP is generated by dielectric barrier discharge, and F-TiO2/γ-Al2O3 can be prepared by sol-gel method in the laboratory. In the experiment, the different packed materials were packed into the plasma reactor, including γ-Al2O3, TiO2/γ-Al2O3 and F-TiO2/γ-Al2O3. Through a series of characterization methods such as X-ray diffraction, scanning electronic microscopy and Brunner-Emmet-Teller measurements, the results show that the particle size distribution of F-TiO2 is relatively smaller than that of TiO2, and the pore distribution of F-TiO2 is more uniformly distributed than that of TiO2. The relationships among toluene removal efficiency, reactor input energy density, and the equivalent capacitances of air gap and dielectric barrier layer were investigated. The results show that the synergistic technology NTP with F-TiO2/γ-Al2O3 resulted in greater enhancement of toluene removal efficiency and energy efficiency. Especially, when packing with F-TiO2/γ-Al2O3 in NTP reactor, toluene removal efficiency reaches 99% and higher. Based on the data analysis of Fourier Transform Infrared Spectroscopy, the experimental results showed that NTP reactor packed with F-TiO2/γ-Al2O3 resulted in a better inhibition for by-products formation effectively in the gas exhaust.

  16. Usefulness of a large field of view sensor for physicochemical, textural, and yield predictions under industrial goat cheese (Murcia al Vino) manufacturing conditions.

    PubMed

    Rovira, S; García, V; Ferrandini, E; Carrión, J; Castillo, M; López, M B

    2012-11-01

    The applicability of a light backscatter sensor with a large field of view was tested for on-line monitoring of coagulation and syneresis in a goat cheese (Murcia al Vino) manufactured under industrial conditions. Cheesemaking was carried out concurrently in a 12-L pilot vat and a 10,000-L industrial vat following the normal cheesemaking protocol. Cheese moisture, whey fat content, hardness, springiness, and adhesiveness were measured during syneresis. The results obtained show that cutting time is best predicted by considering the coagulation ratio at the inflection point and the percentage increase in the ratio during coagulation, with no need for the first derivative. The large field of view reflectance ratio provided good results for the prediction of moisture content, yield, hardness, springiness, and adhesiveness of the final cheese.

  17. SO2 dispersion and monthly evaluation of the industrial source complex short-term (ISCST32) model at Mina Al-Fahal refinery, Sultanate of Oman.

    PubMed

    Abdul-Wahab, Sabah A

    2003-02-01

    Modeling of air pollutant dispersion has been undertaken for emissions of sulfur dioxide (SO(2)) at the Mina Al-Fahal refinery in the Sultanate of Oman. The study was conducted during the period of November 1999 to October 2000. The Industrial Source Complex Short-Term (ISCST32) air pollution model was adopted to predict the ground level concentration of SO(2) in and around the refinery. The modeling results were validated against measured data during the study period. The comparison, based on the monthly average measurements, showed that the model underestimates the observed SO(2) concentrations. However, the predicted ground level concentrations of SO(2) during the months of September, October, November, and June were in better agreement with the observations. The predicted SO(2) values are presented in the form of concentration contours to determine the spatial distribution of SO(2) and to assess the impact on air quality over the survey area. Predicted SO(2) concentrations were found lower than the World Health Organisation (WHO) guideline value of 365 microg/m(3), with the maximum ground level concentrations being found to occur relatively close to the sources of emission. Moreover, concentration contour patterns for the modeled area vary with changes in meteorological conditions. On the basis of this study, the refinery is not likely to cause any significant deterioration in air quality, and predicted concentrations of SO(2) are well below those likely to influence health.

  18. Process Integration Study of the Decatur HFCS Plant for American Fructose Company, Decatur, AL [Advanced Industrial Heat Pump Applications and Evaluations

    SciTech Connect

    Eastwood, A.

    1989-11-10

    This work has carried out in two phases: Phase 1, identification of opportunities for heat pumps in industrial applications and Phase 2; evaluation of heat pumps in industrial applications. In Phase 1, pinch analysis was applied to several industrial sites to identify the best opportunities for heat pumping and other forms of heat integration. In Phase 2, more detailed analyses were undertaken, including the evaluation of a heat pump installed as a recommendation of Phase 1.

  19. Industrial Ziegler-Type Hydrogenation Catalysts Made from Co(neodecanoate)2 or Ni(2-ethylhexanoate)2 and AlEt3: Evidence for Nanoclusters and Sub-Nanocluster or Larger Ziegler-Nanocluster Based Catalysis

    SciTech Connect

    W Alley; I Hamdemir; Q Wang; A Frenkel; L Li; J Yang; L Menard; R Nuzzo; S Ozkar; et al.

    2011-12-31

    Ziegler-type hydrogenation catalysts are important for industrial processes, namely, the large-scale selective hydrogenation of styrenic block copolymers. Ziegler-type hydrogenation catalysts are composed of a group 8-10 transition metal precatalyst plus an alkylaluminum cocatalyst (and they are not the same as Ziegler-Natta polymerization catalysts). However, for {approx}50 years two unsettled issues central to Ziegler-type hydrogenation catalysis are the nature of the metal species present after catalyst synthesis, and whether the species primarily responsible for catalytic hydrogenation activity are homogeneous (e.g., monometallic complexes) or heterogeneous (e.g., Ziegler nanoclusters defined as metal nanoclusters made from combination of Ziegler-type hydrogenation catalyst precursors). A critical review of the existing literature (Alley et al. J. Mol. Catal. A: Chem. 2010, 315, 1-27) and a recently published study using an Ir model system (Alley et al. Inorg. Chem. 2010, 49, 8131-8147) help to guide the present investigation of Ziegler-type hydrogenation catalysts made from the industrially favored precursors Co(neodecanoate){sub 2} or Ni(2-ethylhexanoate){sub 2}, plus AlEt{sub 3}. The approach and methods used herein parallel those used in the study of the Ir model system. Specifically, a combination of Z-contrast scanning transmission electron microscopy (STEM), matrix assisted laser desorption ionization mass spectrometry (MALDI MS), and X-ray absorption fine structure (XAFS) spectroscopy are used to characterize the transition metal species both before and after hydrogenation. Kinetic studies including Hg(0) poisoning experiments are utilized to test which species are the most active catalysts. The main findings are that, both before and after catalytic cyclohexene hydrogenation, the species present comprise a broad distribution of metal cluster sizes from subnanometer to nanometer scale particles, with estimated mean cluster diameters of about 1 nm for

  20. ALS Association

    MedlinePlus

    ... toward a world without ALS! Walk to Defeat ALS® Walk to Defeat ALS® draws people of all ... We need your help. I Will Advocate National ALS Registry The National ALS Registry is a congressionally ...

  1. Potential for use of industrial waste materials as filter media for removal of Al, Mo, As, V and Ga from alkaline drainage in constructed wetlands--adsorption studies.

    PubMed

    Hua, T; Haynes, R J; Zhou, Y-F; Boullemant, A; Chandrawana, I

    2015-03-15

    The potential to remove Al, Mo, V, As and Ga from alkaline (pH 8.0-8.6) drainage originating from seawater neutralized bauxite processing residue storage areas using constructed wetland technology was studied in a laboratory study. Bauxite processing residue sand, bauxite, alum water treatment sludge and blast furnace slag were investigated as potential active filter materials. Al was shown to precipitate as Al(OH)3 in the pH range 7.0-8.0 in aqueous solution and 6.0-8.5 in the presence of silica sand particles that provided a surface for nucleation. For V As Mo and Ga, adsorption to the surfaces of the adsorbents decreased greatly at elevated pH values (>pH 6-9). Water treatment sludge and bauxite had a greater ability to adsorb V, As and Mo at high pH (As and V at pH 7-9 and Mo at pH 5-7) than processing sand and slag. Adsorption isotherm data for As and V onto all four adsorbent than processing sand and slag. Adsorption isotherm data for As and V onto all four adsorbent materials fitted equally well to the Langmuir and Freundlich equations but for Ga, and to a lesser extent Mo, the Freundlich equation gave higher R(2) values. For all four ions, the maximum adsorption capacity (Langmuir value qmax) was greatest for water treatment sludge. Bauxite adsorbed more Mo, Ga and V than residue sand or slag. The pseudo-second order equation gave a better fit to the experimental kinetic data than the pseudo-first order model suggesting that chemisorption rather than diffusion/exchange was the rate limiting step to adsorption. It was concluded that water treatment sludge and bauxite were the most effective adsorbents and that for effective removal of the target ions the pH of the drainage water needs to be decreased to 6.0-7.0.

  2. ALS - resources

    MedlinePlus

    Resources - ALS ... The following organizations are good resources for information on amyotrophic lateral sclerosis : Muscular Dystrophy Association -- mda.org/disease/amyotrophic-lateral-sclerosis National Amyotrophic Lateral Sclerosis (ALS) Registry -- ...

  3. Industrial diamond

    USGS Publications Warehouse

    Olson, D.W.

    2001-01-01

    An overview of the industrial diamond industry is provided. More than 90 percent of the industrial diamond consumed in the U.S. and the rest of the world is manufactured diamond. Ireland, Japan, Russia, and the U.S. produce 75 percent of the global industrial diamond output. In 2000, the U.S. was the largest market for industrial diamond. Industrial diamond applications, prices for industrial diamonds, imports and exports of industrial diamonds, the National Defense Stockpile of industrial diamonds, and the outlook for the industrial diamond market are discussed.

  4. Industrial garnet

    USGS Publications Warehouse

    Olson, D.W.

    2001-01-01

    A general overview of the industrial garnet industry is provided. About 20 percent of global industrial garnet production takes place in the U.S. During 2000, an estimated 300 kt of industrial garnets were produced worldwide. The U.S. is the world's largest consumer of industrial garnet, consuming 56.9 kt in 2000.

  5. Industrial diamond

    USGS Publications Warehouse

    Olson, D.W.

    2003-01-01

    Statistics on the production, consumption, cost, trade, and government stockpile of natural and synthetic industrial diamond are provided. The outlook for the industrial diamond market is also considered.

  6. Industrial Minerals

    ERIC Educational Resources Information Center

    Bradbury, James C.

    1978-01-01

    The past year is seen as not particularly good for industrial minerals and for industry in general. Environmental concerns continued to trouble the industry with unacceptable asbestos concentrations and chlorofluorocarbon effects on ozone. A halting U.S. economy also affected industrial progress. (MA)

  7. Industry Employment

    ERIC Educational Resources Information Center

    Occupational Outlook Quarterly, 2012

    2012-01-01

    This article illustrates projected employment change by industry and industry sector over 2010-20 decade. Workers are grouped into an industry according to the type of good produced or service provided by the establishment for which they work. Industry employment projections are shown in terms of numeric change (growth or decline in the total…

  8. Industrial diamond

    USGS Publications Warehouse

    Olson, D.W.

    2000-01-01

    Part of the 1999 Industrial Minerals Review. A review of the state of the global industrial diamond industry in 1999 is presented. World consumption of industrial diamond has increased annually in recent years, with an estimated 500 million carats valued between $650 million and $800 million consumed in 1999. In 1999, the U.S. was the world's largest market for industrial diamond and was also one of the world's main producers; the others were Ireland, Russia, and South Africa. Uses of industrial diamonds are discussed, and prices of natural and synthetic industrial diamond are reported.

  9. Al Composites

    NASA Astrophysics Data System (ADS)

    Chandanayaka, Tharaka; Azarmi, Fardad

    2014-05-01

    In the present study, cold spraying technique was used to fabricate a metal matrix composite (MMC) that consists of Ni matrix and 20 vol.% Ni3Al particles at two different particle sizes as reinforcement. This study intends to investigate the effect of reinforcement particle size on microstructural and mechanical properties of cold sprayed MMCs. Two different Ni3Al powders with nominal particle size of -45 to +5 and +45 to 100 μm were used as reinforcement in this study. Cold sprayed Ni-Ni3Al samples were subjected to the microstructural observation and characterization prior to any mechanical testing. Then, samples were tested using nano-indentation, Knoop hardness, Vickers hardness, and Resonance frequency to evaluate their mechanical properties. No significant changes were observed in microstructural characteristics due to different particle sizes. The results obtained from a variety of mechanical testings indicated that the increasing reinforcement particle size resulted in the slight reduction of mechanical properties such as elastic modulus and hardness in cold sprayed MMCs. The mechanical interlock between deposited particles defines the bonding strength in cold sprayed samples. Small size particles have a higher velocity and impact resulting in stronger interlock between deformed particles.

  10. Industrial diamond

    USGS Publications Warehouse

    Olson, D.W.

    2004-01-01

    Part of the 2003 industrial minerals review. Supply and demand data for industrial diamond are provided. Topics discussed are consumption, prices, imports and exports, government stockpiles, and the outlook for 2004.

  11. Industrial diamond

    USGS Publications Warehouse

    Olson, D.W.

    2012-01-01

    Estimated 2011 world production of natural and synthetic industrial diamond was about 4.45 billion carats. During 2011, natural industrial diamonds were produced in more than 20 countries, and synthetic industrial diamond was produced in at least 13 countries. About 98 percent of the combined natural and synthetic global output was produced in China, Ireland, Japan, Russia, South Africa and the United States. China is the world's leading producer of synthetic industrial diamond followed by Russia and the United States.

  12. Industrial diamond

    USGS Publications Warehouse

    Olson, D.W.

    2006-01-01

    In 2005, estimated world production of natural and synthetic industrial diamond was 630 million carats. Natural industrial diamond deposits were found in more than 35 countries. Synthetic industrial diamond is produced in at least 15 countries. More than 81% of the combined natural and synthetic global output was produced in Ireland, Japan, Russia, South Africa and the United States.

  13. Industrial diamond

    USGS Publications Warehouse

    Olson, D.W.

    2011-01-01

    Estimated world production of natural and synthetic industrial diamond was about 4.44 billion carats in 2010. Natural industrial diamond deposits have been found in more than 35 countries, and synthetic industrial diamond is produced in at least 15 countries.

  14. Industrial Microbiology.

    ERIC Educational Resources Information Center

    Demain, Arnold L.; Solomon, Nadine A.

    1981-01-01

    Presents an overview of the field of industrial microbiology, providing historical backgrounds of scientific discoveries in the field and descriptions of industrially important microorganisms. Applied research in industry is also detailed, with mention of gene amplification, DNA recombination, pharmaceutical approaches, and detoxification and…

  15. Industry Employment

    ERIC Educational Resources Information Center

    Occupational Outlook Quarterly, 2010

    2010-01-01

    This article illustrates projected employment change from an industry perspective over the 2008-2018 decade. Workers are grouped into an industry according to the type of good produced or service provided by the establishment in which they work. Industry employment projections are shown in terms of numeric change (growth or decline in the total…

  16. Ni{sub 3}Al aluminide alloys

    SciTech Connect

    Liu, C.T.

    1993-10-01

    This paper provides a brief review of the recent progress in research and development of Ni{sub 3}Al and its alloys. Emphasis has been placed on understanding low ductility and brittle fracture of Ni{sub 3}Al alloys at ambient and elevated temperatures. Recent studies have resulted in identifying both intrinsic and extrinsic factors governing the fracture behavior of Ni{sub 3}Al alloys. Parallel efforts on alloy design using physical metallurgy principles have led to properties for structural use. Industrial interest in these alloys is high, and examples of industrial involvement in processing and utilization of these alloys are briefly mentioned.

  17. Industrial Robots.

    ERIC Educational Resources Information Center

    Reed, Dean; Harden, Thomas K.

    Robots are mechanical devices that can be programmed to perform some task of manipulation or locomotion under automatic control. This paper discusses: (1) early developments of the robotics industry in the United States; (2) the present structure of the industry; (3) noneconomic factors related to the use of robots; (4) labor considerations…

  18. Industrial Minerals.

    ERIC Educational Resources Information Center

    Brady, Lawrence L.

    1983-01-01

    Discusses trends in and factors related to the production of industrial minerals during 1982, indicating that, as 1981 marked a downturn in production of industrial minerals, 1982 continued the trend with temporary and permanent cutbacks in mine and plant production. Includes highlights of several conferences/conference papers in this field.…

  19. Industrial garnet

    USGS Publications Warehouse

    Olson, D.W.

    2000-01-01

    The state of the global industrial garnet industry in 1999 is discussed. Industrial garnet mined in the U.S., which accounts for approximately one-third of the world's total, is usually a solid-solution of almandine and pyrope. The U.S. is the largest consumer of industrial garnet, using an estimated 47,800 st in 1999 as an abrasive and as a filtration medium in the petroleum industry, filtration plants, aircraft and motor vehicle manufacture, shipbuilding, wood furniture finishing operations, electronic component manufacture, ceramics manufacture, and glass production. Prices for crude concentrates ranged from approximately $50 to $110/st and refined garnet from $50 to $215/st in 1999, depending on type, source, quantity purchased, quality, and application.

  20. EDITORIAL: Industrial Process Tomography

    NASA Astrophysics Data System (ADS)

    West, Robert M.

    2004-07-01

    Industrial process tomography remains a multidisciplinary field with considerable interest for many varied participants. Indeed this adds greatly to its appeal. It is a pleasure and a privilege to once again act as guest editor for a special feature issue of Measurement Science and Technology on industrial process tomography, the last being in December 2002. Those involved in the subject appreciate the efforts of Measurement Science and Technology in producing another issue and I thank the journal on their behalf. It can be seen that there are considerable differences in the composition of material covered in this issue compared with previous publications. The dominance of electrical impedance and electrical capacitance techniques is reduced and there is increased emphasis on general utility of tomographic methods. This is encompassed in the papers of Hoyle and Jia (visualization) and Dierick et al (Octopus). Electrical capacitance tomography has been a core modality for industrial applications. This issue includes new work in two very interesting aspects of image reconstruction: pattern matching (Takei and Saito) and simulated annealing (Ortiz-Aleman et al). It is important to take advantage of knowledge of the process such as the presence of only two components, and then to have robust reconstruction methods provided by pattern matching and by simulated annealing. Although crude reconstruction methods such as approximation by linear back projection were utilized for initial work on electrical impedance tomography, the techniques published here are much more advanced. The paper by Kim et al includes modelling of a two-component system permitting an adaption-related approach; the paper by Tossavainen et al models free surface boundaries to enable the estimation of shapes of objects within the target. There are clear improvements on the previous crude and blurred reconstructions where boundaries were merely inferred rather than estimated as in these new developments

  1. Industrial Lubricants

    NASA Astrophysics Data System (ADS)

    Kajdas, C.; Karpińska, A.; Kulczycki, A.

    'Industrial lubricant' gaseous, liquid and solid products cover many applications. A new systems analysis approach is used combining heterogeneous catalysis and tribochemistry. Bearing lubricant applications are discussed in terms of the bearing film thickness and tribological regimes, for liquid and solid lubricants. Compressor and vacuum pump lubricant applications are described. The various classes of hydraulic fluids for industrial applications are explained. The properties, applications and selection of various industrial lubricants for different gears are described. Steam and industrial gas turbine lubricant formulations are discussed and the effects of their degradation products, particularly for valves and filters, are presented. Metalworking lubricant applications are divided into cutting and forming operations and their actions are described. Speciality applications such as process, textile, food-grade, slideway, cylinder and wire rope lubricants are explained.

  2. Fermentation industry

    SciTech Connect

    Irvine, R.L.

    1980-06-01

    This article reviews current literature on the fermentation industry. The reuse, recycling and recovery of by-products previously discarded as waste are mentioned, including a Swedish brewery that hopes to reduce discharge of pollutants and the production of single cell protein from a variety of fermentation wastes. The treatment of wastes to produce food substitutes and fertilizers is mentioned together with treatment methods used in distilleries, wineries and in the pharmaceutical industry. (87 References)

  3. Industrial diamond

    USGS Publications Warehouse

    Olson, D.W.

    2013-01-01

    Estimated 2012 world production of natural and synthetic industrial diamond was about 4.45 billion carats. During 2012, natural industrial diamonds were produced in at least 20 countries, and synthetic industrial diamond was produced in at least 12 countries. About 99 percent of the combined natural and synthetic global output was produced in Belarus, China, Ireland, Japan, Russia, South Africa and the United States. During 2012, China was the world’s leading producer of synthetic industrial diamond followed by the United States and Russia. In 2012, the two U.S. synthetic producers, one in Pennsylvania and the other in Ohio, had an estimated output of 103 million carats, valued at about $70.6 million. This was an estimated 43.7 million carats of synthetic diamond bort, grit, and dust and powder with a value of $14.5 million combined with an estimated 59.7 million carats of synthetic diamond stone with a value of $56.1 million. Also in 2012, nine U.S. firms manufactured polycrystalline diamond (PCD) from synthetic diamond grit and powder. The United States government does not collect or maintain data for either domestic PCD producers or domestic chemical vapor deposition (CVD) diamond producers for quantity or value of annual production. Current trade and consumption quantity data are not available for PCD or for CVD diamond. For these reasons, PCD and CVD diamond are not included in the industrial diamond quantitative data reported here.

  4. Industrial diamond

    USGS Publications Warehouse

    Olson, D.W.

    2007-01-01

    World production of natural and synthetic industrial diamond was about 648 million carats in 2006, with 79 percent of the production coming from Ireland, Japan, Russia, South Africa, and the U.S. U.S. consumption was was an estimated 602 million carats, imports were over 391 million carats, and exports were about 83 million carats. About 87 percent of the industrial diamonds market uses synthetic diamonds, which are expected to become less expensive as technology improves and competition from low-cost producers increases.

  5. Industrial garnet

    USGS Publications Warehouse

    Olson, D.W.

    2006-01-01

    In 2005, US production of crude garnet concentrate for industrial use was 28.4 kt valued at $3.05 million. Refined garnet material sold or used was 30.4 kt valued at $10 million. For the year, the US was one of the world's leading consumers of industrial garnet. Domestic values for crude concentrates for different applications ranged from about $53 to $120/t. In the short term, excess production capacity, combined with suppliers that vary in quality, grain size and mineral type, will keep prices down.

  6. Industrial Microorganisms.

    ERIC Educational Resources Information Center

    Phaff, Herman J.

    1981-01-01

    Describes industrially important yeasts, molds, bacteria, and actinomycetes. Discussed in detail are microbial products, such as primary metabolites, secondary metabolites, enzymes, and capsular polysaccharides. Traces the historical background of human cell culture, mentioning recombinant DNA research and hybridization of normal mammalian cells…

  7. Learned Industriousness.

    ERIC Educational Resources Information Center

    Eisenberger, Robert

    1991-01-01

    Individual differences in industriousness are discussed. It is proposed that reinforcement for increased physical or cognitive performance, or the tolerance of aversive stimulation, gives a reward value to the sensation of high effort and reduces effort's aversiveness. Applications for self-control, moral development, and education are described.…

  8. Industrial garnet

    USGS Publications Warehouse

    Olson, D.W.

    2010-01-01

    In 2009, U.S. production of crude garnet concentrate for industrial use was estimated to be 56.5 kt (62,300 st), valued at about $8.85 million. This was a 10-percent decrease in quantity compared with 2008 production. Refined garnet material sold or used was 28 kt (31,000 st) valued at $7.96 million.

  9. Fermentation Industry.

    ERIC Educational Resources Information Center

    Grady, C. P. L., Jr.; Grady, J. K.

    1978-01-01

    Presents a literature review of wastes from the fermentation industry, covering publications of 1976-77. This review focuses on: (1) alcoholic beverage production; (2) pharmaceuticals and biochemicals production; and (3) biomass production. A list of 62 references is also presented. (HM)

  10. Industrial garnet

    USGS Publications Warehouse

    Olson, D.W.

    2011-01-01

    Garnet has been used as a gemstone since the Bronze Age. However, garnet's angular fractures, relatively high hardness and specific gravity, chemical inertness and nontoxicity make it ideal for many industrial applications. It is also free of crystalline silica and can be recycled.

  11. Industrial garnet

    USGS Publications Warehouse

    Olson, D.W.

    2013-01-01

    Garnet has been used as a gemstone since the Bronze Age. However, garnet’s angular fractures, relatively high hardness and specific gravity, chemical inertness and nontoxicity make it ideal for many industrial applications. It is also free of crystalline silica and can be recycled.

  12. Industrial garnet

    USGS Publications Warehouse

    Olson, D.W.

    2012-01-01

    Garnet has been used as a gemstone since the Bronze Age. However, garnet's angular fractures, relatively high hardness and specific gravity, chemical inertness, and nontoxicity make it ideal for many industrial applications. It is also free of crystalline silica and can be recycled.

  13. Industrial Orientation.

    ERIC Educational Resources Information Center

    Rasor, Leslie; Brooks, Valerie

    These eight modules for an industrial orientation class were developed by a project to design an interdisciplinary program of basic skills training for disadvantaged students in a Construction Technology Program (see Note). The Drafting module overviews drafting career opportunities, job markets, salaries, educational requirements, and basic…

  14. China's industrial sector in an international context

    SciTech Connect

    Price, Lynn; Worrell, Ernst; Martin, Nathan; Lehman, Bryan; Sinton, Jonathan

    2000-05-01

    The industrial sector accounts for 40% of global energy use. In 1995, developing countries used an estimated 48 EJ for industrial production, over one-third of world total industrial primary energy use (Price et al., 1998). Industrial output and energy use in developing countries is dominated by China, India, and Brazil. China alone accounts for about 30 EJ (National Bureau of Statistics, 1999), or about 23% of world industrial energy use. China's industrial sector is extremely energy-intensive and accounted for almost 75% of the country's total energy use in 1997. Industrial energy use in China grew an average of 6.6% per year, from 14 EJ in 1985 to 30 EJ in 1997 (Sinton et al., 1996; National Bureau of Statistics, 1999). This growth is more than three times faster than the average growth that took place in the world during the past two decades. The industrial sector can be divided into light and heavy industry, reflecting the relative energy-intensity of the manufacturing processes. In China, about 80% of the energy used in the industrial sector is consumed by heavy industry. Of this, the largest energy-consuming industries are chemicals, ferrous metals, and building materials (Sinton et al., 1996). This paper presents the results of international comparisons of production levels and energy use in six energy-intensive subsectors: iron and steel, aluminum, cement, petroleum refining, ammonia, and ethylene. The sectoral analysis results indicate that energy requirements to produce a unit of raw material in China are often higher than industrialized countries for most of the products analyzed in this paper, reflecting a significant potential to continue to improve energy efficiency in heavy industry.

  15. Industrial alliances

    SciTech Connect

    Adams, K.V.

    1993-09-13

    The United States is emerging from the Cold War era into an exciting, but challenging future. Improving the economic competitiveness of our Nation is essential both for improving the quality of life in the United States and maintaining a strong national security. The research and technical skills used to maintain a leading edge in defense and energy now should be used to help meet the challenge of maintaining, regaining, and establishing US leadership in industrial technologies. Companies recognize that success in the world marketplace depends on products that are at the leading edge of technology, with competitive cost, quality, and performance. Los Alamos National Laboratory and its Industrial Partnership Center (IPC) has the strategic goal to make a strong contribution to the nation`s economic competitiveness by leveraging the government`s investment at the Laboratory: personnel, infrastructure, and technological expertise.

  16. Industrial garnet

    USGS Publications Warehouse

    Olson, D.W.

    2007-01-01

    World production of industrial garnet was about 326 kt in 2006, with the U.S. producing about 11 percent of this total. U.S. consumption, imports, and exports were estimated at 74.3 kt, 52.3 kt, and 13.2 kt, respectively. The most important exporters are Australia, China, and India. Although demand is expected to rise over the next 5 years, prices are expected to remain low in the short term.

  17. Microstructure modelling of industrial alloys

    NASA Astrophysics Data System (ADS)

    Herlach, Dieter M.; Gandin, Charles-André; Garcia-Escorial, Asuncion; Henein, Hani; Grün, Gerd-Ulrich; Schneider, Marc; Guédou, Jean-Yves; Kieft, René; Grellier, André

    2005-10-01

    Solidification of alloys is a complex phenomenon arising in many modern experimental techniques and industrial technologies involving casting and surface processing. Deep undercooling of alloys below equilibrium liquidus temperature results in rapid solidification, yielding materials with improved mechanical, magnetic and electrical properties. This MAP project is focusing on the long-term perspective for industrial materials such as Ni- and Al-based alloys. Ni-based multicomponent superalloys are the basis material for the production of, for example, turbine blades; Al-based alloys are highly important for the aerospace and automotive industries. More than 90% of all metallic materials are now produced from the liquid state. So far, efforts have been directed towards optimising the industrial production routes in the casting and foundry industry by computer-assisted modelling and simulation of solidification under different conditions. The goal has been to reduce the time- and energy-consuming treatment of the cast material in order to produce a material with the desired properties.

  18. Industrial concerns

    NASA Astrophysics Data System (ADS)

    2008-04-01

    Physics in industry is worth reporting, but deciding what counts can be a challenge "If a man can make a better mousetrap than his neighbour...the world will make a beaten path to his door." That quotation, which was apparently inspired by a comment that the American essayist Ralph Waldo Emerson made during a lecture in 1871, has long been used to illustrate the power of invention and innovation. While the lowly mousetrap may hardly seem the pinnacle of technology in today's world of iPhones and Blu-ray DVDs, an effective tool to kill mice was certainly a desirable object in Emerson's day (p52).

  19. Industry Support

    NASA Technical Reports Server (NTRS)

    2003-01-01

    NASA Glenn Research Center (GRC) is responsible for the Advanced Communications for Air Traffic Management (AC/ATM) Project, a sub-element task of the Advanced Air Transportation Technologies (AATT) Project of the NASA Aviation System Capacity Program (ASC). The AC/ATM Project is developing new communications technologies and tools that will improve throughput in the U.S. Air Traffic Control System. The goal of the AC/ATM Project is to enable a communications infrastructure providing the capacity, efficiency, and flexibility necessary to realize benefits of the future mature Free-Flight environment. The capabilities and scope of communications technologies needed to accomplish this goal depend on characteristics of the future Free-Flight environment. There are many operational concepts being proposed for a future ATM system to enable user flexibility and efficiency. GRC s focus is on developing new technologies and techniques to support the digital communication of information involving airborne and ground-based users. However, the technologies and techniques must be integrated with the systems and services that industry and the Federal Aviation Administration (FAA) are developing. Thus, GRC needs to monitor and provide input to the various industry and FAA organizations and committees that are specifying new systems and services. Adoption of technologies by the FAA is partially dependent on acceptance of the technology by the aviation community. The commercial aviation community in particular would like to adopt technologies that can be used throughout the world. As a result, the adoption of common or at least compatible technologies by European countries is a key factor in getting commitments to those technologies by the US aviation community. GRC desires to keep informed of European activities that relate to aviation communication technologies, particularly those that are being supported by Eurocontrol.

  20. Thermal Conductivity of Al-Salt Composites

    NASA Astrophysics Data System (ADS)

    Li, Peng; Zhang, Mei; Wang, Lijun; Seetharaman, Seshadri

    2015-11-01

    With a view to examine the possibility of estimating the content of entrapped metallic aluminium in the salt cake from aluminium remelting, the thermal diffusivity of reference composites of KCl-NaCl-Al was measured as a function of aluminium metal content at room temperature. The thermal conductivity of the reference composites was found to increase with the metallic Al content. The lumped parameter model approach was carried out to discuss the influence of different geometry arrangements of each phase, viz. air, salts and metallic aluminium on the thermal conductivity. Application of the present results to industrial samples indicates that factors such as the interfacial condition of metallic Al particles have to be considered in order to estimate the amount of entrapped Al in the salt cake.

  1. Industrial Productivity

    NASA Technical Reports Server (NTRS)

    1977-01-01

    NASTRAN is an offshoot of the computer-design technique used in construction of airplanes and spacecraft. [n this technique engineers create a mathematical model of the aeronautical or space vehicle and "fly" it on the ground by means of computer simulation. The technique enables them to study performance and structural behavior of a number of different designs before settling on the final configuration and proceeding with construction. From this base of aerospace experience, NASA-Goddard developed the NASTRAN general purpose computer program, which offers an exceptionally wide range of analytic capability with regard to structures. NASTRAN has been applied to autos, trucks, railroad cars, ships, nuclear power reactors, steam turbines, bridges, and office buildings. NASA-Langley provides program maintenance services regarded as vital by many NASTRAN users. NASTRAN is essentially a predictive tool. It takes an electronic look at a computerire$.dedgn and reports how the structure will react under a great many different conditions. It can, for example, note areas where high stress levels will occur-potential failure points that need strengthening. Conversely, it can identify over-designed areas where weight and material might be saved safely. NASTRAN can tell how pipes stand up under strong fluid flow, how metals are affected by high temperatures, how a building will fare in an earthquake or how powerful winds will cause a bridge to oscillate. NASTRAN analysis is quick and inexpensive. It minimizes trial-and-error in the design process and makes possible better, safe, lighter structures affording large-scale savings in development time and materials. Some examples of the broad utility NASTRAN is finding among industrial firms are shown on these pages.

  2. Precipitant diffusion and surface segregation in Al Alloys near melting point: Al 2024

    NASA Astrophysics Data System (ADS)

    Mohney, Austin; Senevirathne, Indrajith

    2012-02-01

    Industrial Al alloys are precipitant hardened with an impurity phase. Micro precipitants introduce various novel physical properties to the systems system. The diffusion of these constituents under thermal gradient was studied by sequentially increasing temperatures near melting point as it was observed to better facilitate the migration of precipitants. Study is based on Al 2024, age hardened, high strength AL alloy, annealed at incremental temperatures near melting point of 500 C and was observed in Scanning Electron Microscopy (SEM) and Energy Dispersive X ray Spectroscopy (EDX). Solvent cleaned near surface region of the alloy was investigated with observation of differential migration of constituent Cu, Fe Mg and Zn precipitants. The migrations were modeled in terms of diffusion coefficients and established literature of the participating species. Study will attempt to correlate the elemental concentration variation with applied elevated heat stress in industrial settings.

  3. Instandhaltungsmanagement als Gestaltungsfeld Ganzheitlicher Produktionssysteme

    NASA Astrophysics Data System (ADS)

    Dombrowski, Uwe; Schulze, Sven; Otano, Isabel Crespo

    Sich kontinuierlich verändernde Rahmenbedingungen, wie beispielsweise eine steigende Variantenvielfalt, verkürzte Produktlebenszyklen sowie Kundenforderungen nach höherer Qualität, kürzeren Lieferzeiten und geringeren Kosten, fordern von produzierenden Unternehmen eine stetige Anpassung der Prozesse, der Organisation und der Strukturen. Seit den 90er Jahren versuchen immer mehr deutsche Unternehmen diesen veränderten Anforderungen mit der Einführung eines Ganzheitlichen Produktionssystems (GPS) zu begegnen. Ganzheitliche Produktionssysteme sind dabei in ihren Grundlagen an das Toyota Produktionssystem angelehnt, vereinigen aber auch weitere Methoden zu einem unternehmensspezifischen Regelwerk. Im Rahmen des langfristigen Trends zu unternehmensindividuellen Produktionssystemen wird sowohl in der Industrie als auch in der Forschung intensiv über das Toyota Produktionssystem, Lean Production, Lean Management und Ganzheitliche Produktionssysteme diskutiert, werden Konzepte zu Implementierung und Betrieb erstellt und die Wirtschaftlichkeit untersucht.

  4. Overview of the development of FeAl intermetallic alloys

    SciTech Connect

    Maziasz, P.J.; Liu, C.T.; Goodwin, G.M.

    1995-09-01

    B2-phase FeAl ordered intermetallic alloys based on an Fe-36 at.% Al composition are being developed to optimize a combination of properties that includes high-temperature strength, room-temperature ductility, and weldability. Microalloying with boron and proper processing are very important for FeAl properties optimization. These alloys also have the good to outstanding resistance to oxidation, sulfidation, and corrosion in molten salts or chlorides at elevated temperatures, characteristic of FeAl with 30--40 at.% Al. Ingot- and powder-metallurgy (IM and PM, respectively) processing both produce good properties, including strength above 400 MPa up to about 750 C. Technology development to produce FeAl components for industry testing is in progress. In parallel, weld-overlay cladding and powder coating technologies are also being developed to take immediate advantage of the high-temperature corrosion/oxidation and erosion/wear resistance of FeAl.

  5. [Environmental factors in ALS].

    PubMed

    Juntas-Morales, Raul; Pageot, Nicolas; Corcia, Philippe; Camu, William

    2014-05-01

    ALS is likely to be a disorder of multifactorial origin. Among all the factors that may increase the risk of ALS, environmental ones are being studied for many years, but in the recent years, several advances have pointed to a new interest in their potential involvement in the disease process, especially for the cyanotoxin BMAA. Food containing BMAA has been found on Guam, a well-known focus of ALS/parkinsonism/dementia and high levels of BMAA have been identified into the brain of these patients. The BMAA cyanotoxin is potentially ubiquitous and have also been found into the food of patients who died from ALS both in Europe and USA. BMAA can be wrongly integrated into the protein structure during mRNA traduction, competing with serine. This may induce abnormal protein folding and a subsequent cell death. Heavy metals, such as lead or mercury may be directly toxic for neuronal cells. Several works have suggested an increased risk of ALS in individuals chronically exposed to these metals. Exposure to pesticides has been suggested to be linked to an increased risk of developing ALS. The mechanism of their toxicity is likely to be mediated by paraoxonases. These proteins are in charge of detoxifying the organism from toxins, and particularly organophosphates. To date, there are insufficient scientific data to suggest that exposure to electromagnetic fields may increase the risk of having ALS. We are particularly missing longitudinal cohorts to demonstrate that risk.

  6. Chemicals Industry Vision

    SciTech Connect

    none,

    1996-12-01

    Chemical industry leaders articulated a long-term vision for the industry, its markets, and its technology in the groundbreaking 1996 document Technology Vision 2020 - The U.S. Chemical Industry. (PDF 310 KB).

  7. Professors and Industry Meet

    ERIC Educational Resources Information Center

    Sheriff, Robert E.

    1974-01-01

    Describes backgrounds of geophysics graduates that are desired for employment by industry. Also listed are areas in which industry could help universities concerning the development of programs to meet the future manpower needs in industry. (BR)

  8. Chemical Industry Corrosion Management

    SciTech Connect

    2003-02-01

    Improved Corrosion Management Could Provide Significant Cost and Energy Savings for the Chemical Industry. In the chemical industry, corrosion is often responsible for significant shutdown and maintenance costs.

  9. Amyotrophic Lateral Sclerosis (ALS)

    MedlinePlus

    ... Pictures of ALS Mutant Proteins Support Two Major Theories About How the Disease is Caused May 2003 ... All NINDS-prepared information is in the public domain and may be freely copied. Credit to the ...

  10. Genetic Testing for ALS

    MedlinePlus

    ... Involved Donate Familial Amyotrophic Lateral Sclerosis (FALS) and Genetic Testing By Deborah Hartzfeld, MS, CGC, Certified Genetic ... guarantee a person will develop symptoms of ALS. Genetic Counseling If there is more than one person ...

  11. All About ALS

    MedlinePlus

    ... External link, please review our exit disclaimer . Subscribe All About ALS Understanding a Devastating Disorder In the ... a coffee pot, or button a shirt. Eventually, all muscles under voluntary control are affected, and people ...

  12. What Is ALS?

    MedlinePlus

    ... scarring or hardening ("sclerosis") in the region. Motor neurons reach from the brain to the spinal cord ... the body. The progressive degeneration of the motor neurons in ALS eventually leads to their demise. When ...

  13. Extensive genetics of ALS

    PubMed Central

    Calvo, Andrea; Mazzini, Letizia; Cantello, Roberto; Mora, Gabriele; Moglia, Cristina; Corrado, Lucia; D'Alfonso, Sandra; Majounie, Elisa; Renton, Alan; Pisano, Fabrizio; Ossola, Irene; Brunetti, Maura; Traynor, Bryan J.; Restagno, Gabriella

    2012-01-01

    Objective: To assess the frequency and clinical characteristics of patients with mutations of major amyotrophic lateral sclerosis (ALS) genes in a prospectively ascertained, population-based epidemiologic series of cases. Methods: The study population includes all ALS cases diagnosed in Piemonte, Italy, from January 2007 to June 2011. Mutations of SOD1, TARDBP, ANG, FUS, OPTN, and C9ORF72 have been assessed. Results: Out of the 475 patients included in the study, 51 (10.7%) carried a mutation of an ALS-related gene (C9ORF72, 32; SOD1, 10; TARDBP, 7; FUS, 1; OPTN, 1; ANG, none). A positive family history for ALS or frontotemporal dementia (FTD) was found in 46 (9.7%) patients. Thirty-one (67.4%) of the 46 familial cases and 20 (4.7%) of the 429 sporadic cases had a genetic mutation. According to logistic regression modeling, besides a positive family history for ALS or FTD, the chance to carry a genetic mutation was related to the presence of comorbid FTD (odds ratio 3.5; p = 0.001), and age at onset ≤54 years (odds ratio 1.79; p = 0.012). Conclusions: We have found that ∼11% of patients with ALS carry a genetic mutation, with C9ORF72 being the commonest genetic alteration. Comorbid FTD or a young age at onset are strong indicators of a possible genetic origin of the disease. PMID:23100398

  14. New challenges and opportunities for industrial biotechnology

    PubMed Central

    2012-01-01

    Industrial biotechnology has not developed as fast as expected due to some challenges including the emergences of alternative energy sources, especially shale gas, natural gas hydrate (or gas hydrate) and sand oil et al. The weaknesses of microbial or enzymatic processes compared with the chemical processing also make industrial biotech products less competitive with the chemical ones. However, many opportunities are still there if industrial biotech processes can be as similar as the chemical ones. Taking advantages of the molecular biology and synthetic biology methods as well as changing process patterns, we can develop bioprocesses as competitive as chemical ones, these including the minimized cells, open and continuous fermentation processes et al. PMID:22905695

  15. Nanocoatings for High-Efficiency Industrial Hydraulic and Tooling Systems

    SciTech Connect

    2009-05-01

    This factsheet describes a research project whose goal is to develop degradation-resistant nano-coatings of AlMgB14 and AlMgB14– (titanium diboride) TiB2 that result in improved surface hardness and reduced friction for industrial hydraulic and tooling systems.

  16. Cost-Effective TiAl based Materials

    NASA Technical Reports Server (NTRS)

    Moxson, V. S.; Sun, Fusheng; Draper, Susan L.; Froes, F. H.; Duz, V.

    2003-01-01

    Because of their inherent low ductility, TiAl-based materials are difficult to fabricate, especially thin gage titanium gamma aluminide (TiAl) sheet and foil. In this paper, an innovative powder metallurgy approach for producing cost-effective thin gage TiAl sheets (with 356 mm long and 235 mm wide, and a thickness of 0.74, 1.09, 1.55, and 2.34 mm, respectively) is presented. The microstructures and tensile properties at room and elevated temperatures of the thin gage TiAl are studied. Results show that these TiAl sheets have a relatively homogenous chemistry, uniform microstructure, and acceptable mechanical properties. This work demonstrates a cost-effective method for producing both flat products (sheet/foil) and complex chunky parts of TiAl for various advanced applications including aerospace and automotive industries.

  17. Molecular and phenotypic characterization of Als1 and Als2 mutations conferring tolerance to acetolactate synthase herbicides in soybean

    PubMed Central

    Walter, Kay L; Strachan, Stephen D; Ferry, Nancy M; Albert, Henrik H; Castle, Linda A; Sebastian, Scott A

    2014-01-01

    BACKGROUND Sulfonylurea (SU) herbicides are effective because they inhibit acetolactate synthase (ALS), a key enzyme in branched-chain amino acid synthesis required for plant growth. A soybean line known as W4-4 was developed through rounds of seed mutagenesis and was demonstrated to have a high degree of ALS-based resistance to both post-emergence and pre-emergence applications of a variety of SU herbicides. This report describes the molecular and phenotypic characterization of the Als1 and Als2 mutations that confer herbicide resistance to SUs and other ALS inhibitors. RESULTS The mutations are shown to occur in two different ALS genes that reside on different chromosomes: Als1 (P178S) on chromosome 4 and Als2 (W560L) on chromosome 6 (P197S and W574L in Arabidopsis thaliana). CONCLUSION Although the Als1 and Als2 genes are unlinked, the combination of these two mutations is synergistic for improved tolerance of soybeans to ALS-inhibiting herbicides. © 2014 DuPont Pioneer. Pest Management Science published by JohnWiley & Sons Ltd on behalf of Society of Chemical Industry. PMID:24425499

  18. Energy conservation in industry

    SciTech Connect

    Strub, A.S.; Ehringer, H.

    1984-01-01

    This book discusses combustion and heat recovery, engines and batteries, and applications and technologies. Some of the topics covered include: energy-saving technologies; heat exchangers, fluidized bed exchangers, industrial heat pumps; fluidized bed combustion; waste heat recovery; orc machines and cascading; engines and flywheels; new types of engines; advanced batteries; fuel cell; chemical industry and catalysis; metallurgy; textile industry; food industry; microwave applications; and cement and glass ceramic industry.

  19. ALS superbend magnet system

    SciTech Connect

    Zbasnik, J.; Wang, S.T.; Chen, J.Y.; DeVries, G.J.; DeMarco, R.; Fahmie, M.; Geyer, A.; Green, M.A.; Harkins, J.; Henderson, T.; Hinkson, J.; Hoyer, E.H.; Krupnick, J.; Marks, S.; Ottens, F.; Paterson, J.A.; Pipersky, P.; Portmann, G.; Robin, D.A.; Schlueter, R.D.; Steier, C.; Taylor, C.E.; Wahrer, R.

    2000-09-15

    The Lawrence Berkeley National Laboratory is preparing to upgrade the Advanced Light Source (ALS) with three superconducting dipoles (Superbends). In this paper we present the final magnet system design which incorporates R&D test results and addresses the ALS operational concerns of alignment, availability, and economy. The design incorporates conduction-cooled Nb-Ti windings and HTS current leads, epoxy-glass suspension straps, and a Gifford-McMahon cryocooler to supply steady state refrigeration. We also present the current status of fabrication and testing.

  20. Modulus measurements in ordered Co-Al, Fe-Al, and Ni-Al alloys

    NASA Technical Reports Server (NTRS)

    Harmouche, M. R.; Wolfenden, A.

    1985-01-01

    The composition and/or temperature dependence of the dynamic Young's modulus for the ordered B2 Co-Al, Fe-Al, and Ni-Al aluminides has been investigated using the piezoelectric ultrasonic composite oscillator technique (PUCOT). The modulus has been measured in the composition interval 48.49 to 52.58 at. pct Co, 50.87 to 60.2 at. pct Fe, and 49.22 to 55.95 at. pct Ni for Co-Al, Fe-Al, and Ni-Al, respectively. The measured values for Co-Al are in the temperature interval 300 to 1300 K, while those for the other systems are for ambient temperature only. The data points show that Co-Al is stiffer than Fe-Al, which is stiffer than Ni-Al. The data points for Fe-Al and Ni-Al are slightly higher than those reported in the literature.

  1. Al Shanker Remembers.

    ERIC Educational Resources Information Center

    American Educator, 2000

    2000-01-01

    In a 1996 interview shortly before his death, Al Shanker, longtime president of the American Federation of Teachers, discussed such topics as: his own educational experiences; how he learned about political fighting in the Boy Scouts; the appeal of socialism; multinational corporations and the nation state; teaching tough students; and John Dewey…

  2. Fosetyl-al

    Integrated Risk Information System (IRIS)

    Fosetyl - al ; CASRN 39148 - 24 - 8 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogenic Ef

  3. ALS renewal moves forward

    NASA Astrophysics Data System (ADS)

    Falcone, R. W.; Feinberg, B.; Hussain, Z.; Kirz, J.; Krebs, G. F.; Padmore, H. A.; Robin, D. S.; Robinson, A. L.

    2007-11-01

    As the result of an extensive long-term planning process involving all its stakeholders—management, staff, and users—the ALS has seen its future and is aggressively moving ahead to implement its vision for keeping the facility at the cutting edge for the next 2-3 decades. The evolving strategic plan now in place aims to renew the ALS so it can address a new generation of fundamental questions about size dependent and dimensional-confinement phenomena at the nanoscale; correlation and complexity in physical, biological, and environmental systems; and temporal evolution, assembly, dynamics and ultrafast phenomena. The renewal spans three areas: (1) increased staffing at beamlines to support the growing user community and safety professionals to keep an increasingly complex facility hazard free; (2) implementing advances in accelerator, insertion device, beamline, and detector technology that will make it possible for ALS users to address emerging grand scientific and technological challenges with incisive world-class tools; and (3) construction of a user support building and guest housing that will increase the safety and user friendliness of the ALS by providing users office, meeting, experiment staging, and laboratory space for their work and on-site accommodations at reasonable rates.

  4. The World Oil Industry

    ERIC Educational Resources Information Center

    Rand, Christopher T.

    1976-01-01

    America's domestic petroleum industry and the international industry have been dominated by seven major firms. Although production costs decreased, sale prices soared with developing political-corporate interrelationships. (MR)

  5. Industrial storage applications overview

    NASA Technical Reports Server (NTRS)

    Duscha, R. A.

    1980-01-01

    The implementation of a technology demonstration for the food processing industry, development and technology demonstrations for selected near-term, in-plant applications and advanced industrial applications of thermal energy storage are overviewed.

  6. Robotics and Industrial Arts.

    ERIC Educational Resources Information Center

    Edmison, Glenn A.; And Others

    Robots are becoming increasingly common in American industry. By l990, they will revolutionize the way industry functions, replacing hundreds of workers and doing hot, dirty jobs better and more quickly than the workers could have done them. Robotics should be taught in high school industrial arts programs as a major curriculum component. The…

  7. Functions of Industry.

    ERIC Educational Resources Information Center

    Georgia Southern Coll., Statesboro.

    Intended for teachers of industrial arts in teaching the functions of industry, this course of study was compiled as a result of the EPDA Institute in Industrial and Career Development at Georgia Southern College. Contents are: (1) Introduction, (2) Organization, (3) Research and Development, (4) Production, (5) Marketing, (6) Finance and Control,…

  8. FOSSIL FUEL INDUSTRIES

    EPA Science Inventory

    The chapter focuses on methane emissions from the coal and natural gas industries. The petroleum industry is not addressed because of the lack of related quality data. Emission points are identified for each industry, and a discussion of factors affecting emissions is presented. ...

  9. Astronomers Working in Industry.

    ERIC Educational Resources Information Center

    Bless, Robert C.; King, Ivan R.

    1981-01-01

    Four scientists, trained as astronomers, describe their astronomical training and present careers in non-astronomy, industrial jobs. They recount some of the differences, positive and negative, between industrial and academic employment, and comment on some of the attitudes they perceive academic and industrial scientists hold toward each other.…

  10. Photovoltaics industry profile

    NASA Astrophysics Data System (ADS)

    1980-10-01

    A description of the status of the U.S. photovoltaics industry is given. Principal end user industries are identified, domestic and foreign market trends are discussed, and industry organized and U.S. government organized trade promotion events are listed. Trade associations and trade journals are listed, and a photovoltaic product manufacturers list is included.

  11. An industrial perpective

    SciTech Connect

    Cunningham, R.A.

    1996-12-31

    The paper consists of conference presentation viewgraphs. The outlined information includes opinions on the status of cogeneration in industrial U.S. markets. A review of the industry and perceived opportunities and challenges are described. Key issues include using the Btu as the commodity of cogeneration and the uncertainties of electric industry restructuring.

  12. Industrial Fire Brigade Training.

    ERIC Educational Resources Information Center

    North Carolina State Dept. of Community Colleges, Raleigh.

    Organized as a teaching outline for an industrial plant fire brigade course, this manual contains a rationale for an industrial plant brigade as an adjunct to the local firefighting services; information to the instructor concerning the implementation of an industrial fire brigade program; and a teaching outline consisting of eleven sections: (1)…

  13. 2011 Training Industry Report

    ERIC Educational Resources Information Center

    Training, 2011

    2011-01-01

    This article presents "Training" magazine's exclusive analysis of the U.S. training industry, featuring 2011 training expenditures, budgetary allocations, delivery methods, and training priorities. Now in its 30th year, The Industry Report is recognized as the training industry's most trusted source of data on budgets, staffing, and programs. This…

  14. Ausbildung als zentrale Aufgabe

    NASA Astrophysics Data System (ADS)

    Krämer, Walter; Schmerbach, Sibylle

    Anders als Lesen und Schreiben zählen Grundkenntnisse in Statistik heute noch nicht zu den Voraussetzungen einer sinnvollen Teilhabe am Sozialgeschehen. Und auch in der akademischen Statistik-Ausbildung gibt es noch einiges zu tun. Das vorliegende Kapitel zeichnet die Geschichte dieser akademischen Ausbildung an deutschen Universitäten nach dem zweiten Weltkrieg nach, stellt aktuelle Defizite vor und weist auf mögliche Verbesserungen hin.

  15. Uranium industry annual 1998

    SciTech Connect

    1999-04-22

    The Uranium Industry Annual 1998 (UIA 1998) provides current statistical data on the US uranium industry`s activities relating to uranium raw materials and uranium marketing. It contains data for the period 1989 through 2008 as collected on the Form EIA-858, ``Uranium Industry Annual Survey.`` Data provides a comprehensive statistical characterization of the industry`s activities for the survey year and also include some information about industry`s plans and commitments for the near-term future. Data on uranium raw materials activities for 1989 through 1998, including exploration activities and expenditures, EIA-estimated reserves, mine production of uranium, production of uranium concentrate, and industry employment, are presented in Chapter 1. Data on uranium marketing activities for 1994 through 2008, including purchases of uranium and enrichment services, enrichment feed deliveries, uranium fuel assemblies, filled and unfilled market requirements, and uranium inventories, are shown in Chapter 2. The methodology used in the 1998 survey, including data edit and analysis, is described in Appendix A. The methodologies for estimation of resources and reserves are described in Appendix B. A list of respondents to the ``Uranium Industry Annual Survey`` is provided in Appendix C. The Form EIA-858 ``Uranium Industry Annual Survey`` is shown in Appendix D. For the readers convenience, metric versions of selected tables from Chapters 1 and 2 are presented in Appendix E along with the standard conversion factors used. A glossary of technical terms is at the end of the report. 24 figs., 56 tabs.

  16. Metalcasting Industry Technology Roadmap

    SciTech Connect

    none,

    1998-01-01

    The Roadmap sets out the strategy for pursuing near-, mid-, and long-term goals set out by industry and for carrying out the cooperative agreement between the U.S. Department of Energy and industry. The Roadmap outlines key goals for products and markets, materials technology, manufacturing technology, environmental technology, human resources, and industry health programs. The Roadmap sets out the strategy for pursuing near-, mid-, and long-term goals set out by industry and for carrying out the cooperative agreement between the U.S. Department of Energy and industry. The Roadmap sets out the strategy for pursuing near-, mid-, and long-term goals set out by industry and for carrying out the cooperative agreement between the U.S. Department of Energy and industry.

  17. Evolution of Fe Bearing Intermetallics During DC Casting and Homogenization of an Al-Mg-Si Al Alloy

    NASA Astrophysics Data System (ADS)

    Kumar, S.; Grant, P. S.; O'Reilly, K. A. Q.

    2016-06-01

    The evolution of iron (Fe) bearing intermetallics (Fe-IMCs) during direct chill casting and homogenization of a grain-refined 6063 aluminum-magnesium-silicon (Al-Mg-Si) alloy has been studied. The as-cast and homogenized microstructure contained Fe-IMCs at the grain boundaries and within Al grains. The primary α-Al grain size, α-Al dendritic arm spacing, IMC particle size, and IMC three-dimensional (3D) inter-connectivity increased from the edge to the center of the as-cast billet; both α c-AlFeSi and β-AlFeSi Fe-IMCs were identified, and overall α c-AlFeSi was predominant. For the first time in industrial billets, the different Fe-rich IMCs have been characterized into types based on their 3D chemistry and morphology. Additionally, the role of β-AlFeSi in nucleating Mg2Si particles has been identified. After homogenization, α c-AlFeSi predominated across the entire billet cross section, with marked changes in the 3D morphology and strong reductions in inter-connectivity, both supporting a recovery in alloy ductility.

  18. Deep SiO2 etching with Al and AlN masks for MEMS devices

    NASA Astrophysics Data System (ADS)

    Bliznetsov, Vladimir; Mao Lin, Hua; Zhang, Yue Jia; Johnson, David

    2015-08-01

    Silicon oxide-based materials such as quartz and silica are widely used in microelectromechanical systems (MEMS). One way to enhance the capability of their deep plasma etching is to increase selectivity by the use of hard masks. Although this approach was studied previously, information on the use of hard masks for the etching of silicon-oxide based materials on 200 mm substrates is scarce. We present the results of etching process development for amorphous silicon oxide using Al and AlN masks with a view of the application of the results for the etching of silica and quartz. Three gas chemistries (C4F8/O2, CF4 and SF6) and their mixtures were compared in an industrial reactive ion etch (RIE) chamber with two plasma sources. It was established that pure SF6 is the best etchant and AlN is a better mask than Al for providing higher selectivity and a sidewall angle close to vertical. A range of etching parameters for micromasking-free etching was established and etched structures of up to a 4 : 1 aspect ratio were created in 21 μm-thick oxide using the process with an etch rate of 0.32-0.36 μm min-1 and a selectivity to AlN mask of (38-49) : 1.

  19. AL Amyloidosis and Agent Orange

    MedlinePlus

    ... for survivors' benefits . Research on AL amyloidosis and herbicides The Health and Medicine Division (formally known as ... to the compounds of interest found in the herbicide Agent Orange and AL amyloidosis." VA made a ...

  20. Modeling neuronal vulnerability in ALS.

    PubMed

    Roselli, Francesco; Caroni, Pico

    2014-08-20

    Using computational models of motor neuron ion fluxes, firing properties, and energy requirements, Le Masson et al. (2014) reveal how local imbalances in energy homeostasis may self-amplify and contribute to neurodegeneration in ALS.

  1. Al Jazirah, Sudan

    NASA Technical Reports Server (NTRS)

    2008-01-01

    Al Jazirah (also Gezira) is one of the 26 states of Sudan. The state lies between the Blue Nile and the White Nile in the east-central region of the country. It is a well populated area suitable for agriculture. The area was at the southern end of Nubia and little is known about its ancient history and only limited archaeological work has been conducted in this area. The region has benefited from the Gezira Scheme, a program to foster cotton farming begun in 1925. At that time the Sennar Dam and numerous irrigation canals were built. Al Jazirah became the Sudan's major agricultural region with more than 2.5 million acres (10,000 km) under cultivation. The initial development project was semi-private, but the government nationalized it in 1950. Cotton production increased in the 1970s but by the 1990s increased wheat production has supplanted a third of the land formerly seeded with cotton.

    The image was acquired December 25, 2006, covers an area of 56 x 36.4 km, and is located near 14.5 degrees north latitude, 33.1 degrees east longitude.

    The U.S. science team is located at NASA's Jet Propulsion Laboratory, Pasadena, Calif. The Terra mission is part of NASA's Science Mission Directorate.

  2. Industrial sand and gravel

    USGS Publications Warehouse

    Dolley, T.P.

    2006-01-01

    In 2005, domestic production of industrial sand and gravel was about 31 Mt, a 5% increase from 2004. This increase was bouyed by robust construction and petroleum sectors of the US economy. Based on estimated world production figures, the United States was the world's leading producer and consumer of industrial sand and gravel. In the short term, local shortages of industrial sand and gravel will continue to increase.

  3. A global industry

    SciTech Connect

    1994-12-01

    The independent energy industry has expanded considerably since its beginning in the 1970s. Today, participants are finding new opportunities and new challenges throughout the world. During the past several years, the independent power industry has undergone a rather dramatic exchange. What was once an almost exclusively US-based industry has evolved into a global business with potential new markets in nearly every corner of the world.

  4. Heat pumps for industry

    NASA Astrophysics Data System (ADS)

    1991-09-01

    Research activities, both in the laboratory and in the field, confirm that heat pumps can improve energy efficiency and productivity for a multitude of process types. By using heat pumps, process industries can save significant amounts of energy and money and successfully control emissions. Those industries with special needs, such as recovering solvents, can meet them more energy efficiently and cost effectively with heat pumps. Through the years, the Office of Industrial Technologies (OIT) has helped industry solve its energy problems by joining in cooperative agreements with companies willing to do the research. The companies involved in these agreements share the costs of the research and benefit directly from the technology developed. OIT then has information from demonstration projects that it can pass on to others within industry. All the projects described in this brochure were joint ventures between DOE and industry participants. OIT will assist in accelerating the use of heat pumps in the industrial marketplace by continuing to work with industry on research and demonstration projects and to transfer research results and project performance information to the rest of industry. Successfully transferring this technology could conserve as much as 1.5 quads of energy annually at a savings of more than $4 billion at today's prices.

  5. Influence of impact speed on water droplet erosion of TiAl compared with Ti6Al4V

    PubMed Central

    Mahdipoor, M.S.; Kirols, H.S.; Kevorkov, D.; Jedrzejowski, P.; Medraj, M.

    2015-01-01

    Water Droplet Erosion (WDE) as a material degradation phenomenon has been a concern in power generation industries for decades. Steam turbine blades and the compressor blades of gas turbines that use water injection usually suffer from WDE. The present work focuses on studying erosion resistance of TiAl as a potential alloy for turbine blades compared to Ti6Al4V, a frequently used blade alloy. Their erosion behaviour is investigated at different droplet impact speeds to determine the relation between erosion performance and impact speed. It is found that the relationship is governed by a power law equation, ER ~ Vn, where the speed exponent is 7–9 for Ti6Al4V and 11–13 for TiAl. There is a contrast between the observed speed exponent in this work and the ones reported in the literature for Ti6Al4V. It is attributed to the different erosion setups and impingement conditions such as different droplet sizes. To verify this, the erosion experiments were performed at two different droplet sizes, 464 and 603 μm. TiAl showed superior erosion resistance in all erosion conditions; however, its erosion performance exhibits higher sensitivity to the impact speed compared to Ti6Al4V. It means that aggressive erosion conditions decrease the WDE resistance superiority of TiAl. PMID:26391370

  6. Influence of impact speed on water droplet erosion of TiAl compared with Ti6Al4V.

    PubMed

    Mahdipoor, M S; Kirols, H S; Kevorkov, D; Jedrzejowski, P; Medraj, M

    2015-09-22

    Water Droplet Erosion (WDE) as a material degradation phenomenon has been a concern in power generation industries for decades. Steam turbine blades and the compressor blades of gas turbines that use water injection usually suffer from WDE. The present work focuses on studying erosion resistance of TiAl as a potential alloy for turbine blades compared to Ti6Al4V, a frequently used blade alloy. Their erosion behaviour is investigated at different droplet impact speeds to determine the relation between erosion performance and impact speed. It is found that the relationship is governed by a power law equation, ER ~ V(n), where the speed exponent is 7-9 for Ti6Al4V and 11-13 for TiAl. There is a contrast between the observed speed exponent in this work and the ones reported in the literature for Ti6Al4V. It is attributed to the different erosion setups and impingement conditions such as different droplet sizes. To verify this, the erosion experiments were performed at two different droplet sizes, 464 and 603 μm. TiAl showed superior erosion resistance in all erosion conditions; however, its erosion performance exhibits higher sensitivity to the impact speed compared to Ti6Al4V. It means that aggressive erosion conditions decrease the WDE resistance superiority of TiAl.

  7. Influence of impact speed on water droplet erosion of TiAl compared with Ti6Al4V.

    PubMed

    Mahdipoor, M S; Kirols, H S; Kevorkov, D; Jedrzejowski, P; Medraj, M

    2015-01-01

    Water Droplet Erosion (WDE) as a material degradation phenomenon has been a concern in power generation industries for decades. Steam turbine blades and the compressor blades of gas turbines that use water injection usually suffer from WDE. The present work focuses on studying erosion resistance of TiAl as a potential alloy for turbine blades compared to Ti6Al4V, a frequently used blade alloy. Their erosion behaviour is investigated at different droplet impact speeds to determine the relation between erosion performance and impact speed. It is found that the relationship is governed by a power law equation, ER ~ V(n), where the speed exponent is 7-9 for Ti6Al4V and 11-13 for TiAl. There is a contrast between the observed speed exponent in this work and the ones reported in the literature for Ti6Al4V. It is attributed to the different erosion setups and impingement conditions such as different droplet sizes. To verify this, the erosion experiments were performed at two different droplet sizes, 464 and 603 μm. TiAl showed superior erosion resistance in all erosion conditions; however, its erosion performance exhibits higher sensitivity to the impact speed compared to Ti6Al4V. It means that aggressive erosion conditions decrease the WDE resistance superiority of TiAl. PMID:26391370

  8. Influence of impact speed on water droplet erosion of TiAl compared with Ti6Al4V

    NASA Astrophysics Data System (ADS)

    Mahdipoor, M. S.; Kirols, H. S.; Kevorkov, D.; Jedrzejowski, P.; Medraj, M.

    2015-09-01

    Water Droplet Erosion (WDE) as a material degradation phenomenon has been a concern in power generation industries for decades. Steam turbine blades and the compressor blades of gas turbines that use water injection usually suffer from WDE. The present work focuses on studying erosion resistance of TiAl as a potential alloy for turbine blades compared to Ti6Al4V, a frequently used blade alloy. Their erosion behaviour is investigated at different droplet impact speeds to determine the relation between erosion performance and impact speed. It is found that the relationship is governed by a power law equation, ER ~ Vn, where the speed exponent is 7-9 for Ti6Al4V and 11-13 for TiAl. There is a contrast between the observed speed exponent in this work and the ones reported in the literature for Ti6Al4V. It is attributed to the different erosion setups and impingement conditions such as different droplet sizes. To verify this, the erosion experiments were performed at two different droplet sizes, 464 and 603 μm. TiAl showed superior erosion resistance in all erosion conditions; however, its erosion performance exhibits higher sensitivity to the impact speed compared to Ti6Al4V. It means that aggressive erosion conditions decrease the WDE resistance superiority of TiAl.

  9. ALS Performance Summary - Update

    SciTech Connect

    Waters, A M; Brown, W D; Martz, Jr., H E

    2004-09-30

    High Energy Density Physics (HEDP) experiments play an important role in corroborating the improved physics codes that underlie LLNL's Stockpile Stewardship mission. Conducting these experiments, whether on the National Ignition Facility (NIF) or another national facility such as Omega, will require not only improvement in the diagnostics for measuring the experiment, but also detailed knowledge of the as-built target components and assemblies themselves. To assist in this effort, a defined set of well-known reference standards designed to represent a range of HEDP targets have been built and are being used to quantify the performance of different characterization techniques [Hibbard, et al. 2004]. Without the critical step of using reference standards for qualifying characterization tools there can be no verification of either commercial or internally-developed characterization techniques and thus an uncertainty in the input to the physics code models would exist.

  10. The methanol industry`s missed opportunities

    SciTech Connect

    Stokes, C.A.

    1995-12-31

    Throughout its history the methanol industry has been backward in research and development and in industry cooperation on public image and regulatory matters. It has been extremely reticent as to the virtue of its product for new uses, especially for motor fuel. While this is perhaps understandable looking back, it is inexcusable looking forward. The industry needs to cooperate on a worldwide basis in research and market development, on the one hand, and in image-building and political influence, on the other, staying, of course, within the US and European and other regional antitrust regulations. Unless the industry develops the motor fuel market, and especially the exciting new approach through fuel cell operated EVs, to siphon off incremental capacity and keep plants running at 90% or more of capacity, it will continue to live in a price roller-coaster climate. A few low-cost producers will do reasonably well and the rest will just get along or drop out here and there along the way, as in the past. Having come so far from such a humble beginning, it is a shame not to realize the full potential that is clearly there: a potential to nearly double sales dollars without new plants and to produce from a plentiful resource, at least for the next half-century, all the methanol that can be imagined to be needed. Beyond that the industry can turn to renewable energy--the sun--via biomass growth, to make their product. In so doing, it can perhaps apply methanol as a plant growth stimulant, in effect making the product fully self-sustainable. The world needs to know what methanol can do to provide--economically and reliably--the things upon which a better life rests.

  11. Aluminum and silicon diffusion in Fe-Cr-Al alloys

    SciTech Connect

    Heesemann, A.; Schmidtke, E.; Faupel, F.; Kolb-Telieps, A.; Kloewer, J.

    1999-02-05

    Foils of Fe-Cr-Al alloys containing about 20 wt% Cr, 5 wt% Al and additions of Si and reactive elements like Ce, La, Y, Hf, Zr or Ti are widely used as a substrate in metal-supported automotive catalytic converters. In the present paper the authors report on measurements of Al and Si diffusion in Fe-Cr-Al alloys. Due to a lack of suitable radiotracers concentration profiles were obtained by means of electron microprobe analysis. In connection with data evaluation they present numerical calculations assessing the accuracy of the Matano analysis and the thin-film solution of Fick`s 2nd law as function of the thickness of the initial diffusant layer. The results are of general interest, particularly for the evaluation of diffusion measurements involving industrial specimens with given geometry.

  12. Industrial sand and gravel

    USGS Publications Warehouse

    Dolley, T.P.

    2013-01-01

    Domestic production of industrial sand and gravel in 2012 was about 49.5 Mt (55 million st), increasing 13 percent compared with that of 2011. Some important end uses for industrial sand and gravel include abrasives, filtration, foundry, glassmaking, hydraulic fracturing sand (frac sand) and silicon metal applications.

  13. Industrial sand and gravel

    USGS Publications Warehouse

    Dolley, T.P.

    2012-01-01

    Domestic production of industrial sand and gravel in 2011 was about 30 Mt (33 million st), increasing slightly compared with 2010. Some important end uses for industrial sand and gravel include abrasives, filtration, foundry, glassmaking, hydraulic fracturing sand (frac sand) and silicon metal applications.

  14. Rebuilding America's Industrial Strength

    ERIC Educational Resources Information Center

    Community College Journal, 2011

    2011-01-01

    It's no secret within the academic or manufacturing communities that community colleges are the nation's training ground for industrial-skilled trade careers. But outside community college classrooms and industrial plants, many people are in the dark about the growing numbers of these often-well-paid and in-demand jobs. This article introduces the…

  15. Industrial sand and gravel

    USGS Publications Warehouse

    Dolley, T.P.

    2011-01-01

    Domestic production of industrial sand and gravel in 2010 was about 26.5 Mt (29.2 million st), a 6-percent increased from 2009. Certain end uses of industrial sand and gravel, such as sand for container glass, golf course sand, recreational sand, specialty glass and water filtration, showed increased demand in 2010.

  16. INDUSTRIAL ARTS HANDBOOK.

    ERIC Educational Resources Information Center

    JOHNSON, ALLEN

    TO AID TEACHERS, GUIDANCE COUNSELORS, AND ADMINISTRATORS, AS WELL AS THE STUDENT HIMSELF, THE HANDBOOK OFFERED PURPOSES AND COURSE DESCRIPTIONS IN THE FIELD OF INDUSTRIAL ARTS. IT APPLIED TO ELEMENTARY, JUNIOR HIGH, AND SENIOR HIGH SCHOOL STUDENTS. INDUSTRIAL ARTS PROVIDED AN OPPORTUNITY FOR STUDENTS TO DISCOVER THEIR APTITUDES AND ABILITIES IN…

  17. Industrial Waste Reduction Program

    SciTech Connect

    Not Available

    1991-10-24

    US industry generates over 12 billion tons of wastes each year. These wastes consist of undesirable by-products of industrial production that are discarded into our environment. Energy is an integral part of these wastes; it is found in the embodied energy of industrial feedstocks not optimally used, in the energy content of the wastes themselves, and in the energy needed to transport, treat, and dispose of wastes. Estimates of the potential energy savings from reducing industrial wastes range from three to four quadrillion Btu per year -- enough to meet the annual energy needs of 30 million American homes. This document presents a plan for the Industrial Waste Reduction Program, which has been designed to help achieve national goals for energy efficiency and waste minimization. The objective of the program is to improve the energy efficiency of industrial processes through cost-effective waste reduction. The initial program focus is on waste reduction opportunities in the production and use of chemicals, due to the significant amount of energy used in these activities and the large amounts of hazardous and toxic wastes they generate. The chemical industry will be the initial subject of a series of waste reduction opportunity assessments conducted as part of the program. Assessments of other industries and waste problems will follow.

  18. INDUSTRIAL TRAINING RESEARCH REGISTER.

    ERIC Educational Resources Information Center

    Ministry of Labour, London (England).

    IN THIS CLASSIFIED REGISTER OF CURRENT AND RECENTLY COMPLETED STUDIES OF INDUSTRIAL TRAINING IN GREAT BRITAIN, INDIVIDUAL PROJECTS ARE ARRANGED BY THE ITEM NUMBER JUDGED MOST IMPORTANT, AND THE NUMBERS OF OTHER RELEVANT INDUSTRIAL RESEARCH PROJECTS ARE INSERTED AT THE END OF EACH SECTION TO PROVIDE CROSS REFERENCES. DESCRIPTIONS INCLUDE THE TITLE…

  19. Analysis of Industrial Wastewaters.

    ERIC Educational Resources Information Center

    Mancy, K. H.; Weber, W. J., Jr.

    A comprehensive, documented discussion of certain operating principles useful as guidelines for the analysis of industrial wastewaters is presented. Intended primarily for the chemist, engineer, or other professional person concerned with all aspects of industrial wastewater analysis, it is not to be considered as a substitute for standard manuals…

  20. The Industrial City

    ERIC Educational Resources Information Center

    Mohl, Raymond

    1976-01-01

    This article, the sixth installment in Environment's "Looking Back" series, traces the woes of America's industrialized cities to the movement that developed cities primarily as centers for industrial enterprise rather than as places for people to live. Today's social ills, from pollution to poverty, developed from that movement. (BT)

  1. Exploring the Industrial Subculture.

    ERIC Educational Resources Information Center

    Turner, Barry A.

    This book is an attempt to create a theoretical vocabulary for those who believe that the sociology of industrial organizations should concern itself with discovering the ways in which people in industry define their life-position and with examining the collective and organizational consequences of these views which they hold of themselves. Using…

  2. Collapse of an industry

    SciTech Connect

    Campbell, J.L.

    1988-01-01

    The author details the politics of nuclear energy in the U.S. and points out the advantages and disadvantages of various forms of industrial planning for this sector. He uses the nuclear industry as an example of how capitalism and democracy can be incompatible in some situations.

  3. INDUSTRIAL RADIOGRAPHY INSTRUCTOR'S GUIDE.

    ERIC Educational Resources Information Center

    Bureau of Adult, Vocational, and Technical Education (DHEW/OE), Washington, DC. Div. of Vocational and Technical Education.

    THIS LABORATORY GUIDE WAS DEVELOPED FOR AN 80-HOUR COURSE IN INDUSTRIAL RADIOGRAPHY FOR HIGH SCHOOL GRADUATES TRAINING TO BECOME BEGINNING RADIOGRAPHERS. IT IS USED IN CONJUNCTION WITH TWO OTHER VOLUMES--(1) INDUSTRIAL RADIOGRAPHY INSTRUCTOR'S GUIDE, AND (2) INUDSTRIAL RADIOGRAPHY MANUAL. THE PROGRAM WAS DEVELOPED BY A COMMITTEE OF REPRESENTATIVES…

  4. Industrial Arts Facilities.

    ERIC Educational Resources Information Center

    Georgia State Dept. of Education, Atlanta. Office of Vocational Education.

    Requirements and planning guidelines for industrial arts facilities are outlined for application to three types of industrial arts shops. The ratios of areas to students are discussed in regard to the sizes, shapes, and locations of shops. Specifications for walls, floors, ceilings, windows, paint, and illumination are included. An equipment…

  5. Handbook of industrial robotics

    SciTech Connect

    Nof, S.Y.

    1985-01-01

    This book presents papers on the application of artificial intelligence to robots used in industrial plants. Topics considered include vision systems, elements of industrial robot software, robot teaching, the off-line programming of robots, a structured programming robot language, task-level manipulator programming, expert systems, and the role of the computer in robot intelligence.

  6. Foundry Industry Training Committee

    ERIC Educational Resources Information Center

    Industrial Training Journal, 1974

    1974-01-01

    The Foundry Industry Training Committee has encouraged the foundry industry in developing systematic manpower training and development programs at all levels. Features developed include competitions as a technique of standard setting, recommendations for technician training, and a widely used manpower information system. (MW)

  7. Commercial Banking Industry Survey.

    ERIC Educational Resources Information Center

    Bright Horizons Children's Centers, Cambridge, MA.

    Work and family programs are becoming increasingly important in the commercial banking industry. The objective of this survey was to collect information and prepare a commercial banking industry profile on work and family programs. Fifty-nine top American commercial banks from the Fortune 500 list were invited to participate. Twenty-two…

  8. Training in British Industry

    ERIC Educational Resources Information Center

    Jackson, Willis

    2008-01-01

    Purpose: The purpose of this paper is to examine the need for, and development of, further education and practical training for recruits into industry. Design/methodology/approach: The paper discusses how, at the time of writing, many firms were developing and operating training schemes for industrial personnel. Firms benefit themselves from…

  9. Geothermal industry assessment

    SciTech Connect

    Not Available

    1980-07-01

    An assessment of the geothermal industry is presented, focusing on industry structure, corporate activities and strategies, and detailed analysis of the technological, economic, financial, and institutional issues important to government policy formulation. The study is based principally on confidential interviews with executives of 75 companies active in the field. (MHR)

  10. Industry and Instructional Development.

    ERIC Educational Resources Information Center

    Wallington, Clint

    This chapter examines the current state of instructional development (ID) in business and industry, emphasizing the differences between ID in industry and in education. The competency studies of both the American Society for Testing and Development (ASTD) and the Association for Educational Communications and Technology (AECT) are considered, and…

  11. 2010 Training Industry Report

    ERIC Educational Resources Information Center

    Training, 2010

    2010-01-01

    Now in its 29th year, The Industry Report is recognized as the training industry's most trusted source of data on budgets, staffing, and programs. This year, the study was conducted by an outside research firm in June-August 2010, when members from the "Training" magazine database were e-mailed an invitation to participate in an online survey.…

  12. Aluminum Industry Technology Roadmap

    SciTech Connect

    none,

    2003-02-01

    This roadmap describes the industry's R&D strategy, priorities, milestones, and performance targets for achieving its long-term goals. It accounts for changes in the industry and the global marketplace since the first roadmap was published in 1997. An updated roadmap was published November 2001. (PDF 1.1 MB).

  13. Industrial applications of nanoparticles.

    PubMed

    Stark, W J; Stoessel, P R; Wohlleben, W; Hafner, A

    2015-08-21

    Research efforts in the past two decades have resulted in thousands of potential application areas for nanoparticles - which materials have become industrially relevant? Where are sustainable applications of nanoparticles replacing traditional processing and materials? This tutorial review starts with a brief analysis on what makes nanoparticles attractive to chemical product design. The article highlights established industrial applications of nanoparticles and then moves to rapidly emerging applications in the chemical industry and discusses future research directions. Contributions from large companies, academia and high-tech start-ups are used to elucidate where academic nanoparticle research has revolutionized industry practice. A nanomaterial-focused analysis discusses new trends, such as particles with an identity, and the influence of modern instrument advances in the development of novel industrial products.

  14. University/industry research

    NASA Astrophysics Data System (ADS)

    Bell, Peter M.

    The problems encountered in mixing industrial and university research goals can be major, but so can the benefits. The National Science Board (NSB) recently released a report on “University-Industry Research Relationships: Selected Studies” (U.S. Government Printing Office, Washington, DC, 1983). It is an analysis of the much-discussed new trend toward increased industrial funding of university research projects.University laboratories cannot generally solve industry's R&D problems. Success for the corporation in sponsoring academic research is realized in the value of cooperative research programs as training exercises for future industrial scientists. An occasional patent arising from such a project is considered an added benefit, not a primary goal.

  15. Some Investigations on Effect of Cooling Rate on Al2O3 Reinforced Al-MMC Prepared by Vacuum Moulding

    NASA Astrophysics Data System (ADS)

    Singh, Rupinder; Sahni, Kanwalpreet

    2016-07-01

    In the present research work effort has been made to study the effect of cooling rate of Al2O3 reinforced; aluminum metal matrix composites (Al-MMC) on hardness of component prepared by vacuum moulding (VM) process. The study started with selection of the component for industrial application. This study also highlights the effect of reinforcement in form of double particle size and triple particle size on hardness of Al-Al2O3 MMC. The input parameters of process are composition of MMC, vacuum moulding silica sand AFS No., vacuum pressure and component volume. The results of study supported by microstructure analysis suggest the geometric model for MMC hardness prepared by VM process.

  16. Theoretical studies of AlF, AlCl, and AlBr

    NASA Technical Reports Server (NTRS)

    Langhoff, Stephen R.; Bauschlicher, Charles W., Jr.; Taylor, Peter R.

    1988-01-01

    Spectroscopic constants have been obtained for the lowest six singlet and lowest five triplet states of AlF and AlCl. The results suggest that the correct ordering of the triplet manifold in these molecules is: a 3Pi, b 3Sigma(+), c 3Sigma(+), d 3Pi, and e 3Delta. Radiative lifetimes have been determined for the excited states, and the A 1Pi to X 1Sigma(+) transition in AlF, AlCl, and AlBr has been examined in detail. A-X transition moment functions, Einstein coefficients, and A 1Pi vibrational lifetimes have been obtained for AlF and AlCl.

  17. Mask Industry Assessment: 2011

    NASA Astrophysics Data System (ADS)

    Chan, Y. David

    2011-11-01

    A survey supported by SEMATECH and administered by David Powell Consulting was sent to microelectronics industry leaders to gather information about the mask industry as an objective assessment of its overall condition. The survey was designed with the input of semiconductor company mask technologists and merchant mask suppliers. This year's assessment is the tenth in the current series of annual reports. With ongoing industry support, the report has been used as one of the baselines to gain perspective on the technical and business status of the mask and microelectronics industries. It continues to serve as a valuable reference to identify the strengths and opportunities of the mask industry. The results will be used to guide future investments pertaining to critical path issues. This year's survey was essentially the same as the 2005 through 2010 surveys. Questions are grouped into following categories: General Business Profile Information, Data Processing, Yields and Yield Loss Mechanisms, Delivery Times, Returns, and Services. Within each category are multiple questions that result in a detailed profile of both the business and technical status of the critical mask industry. This profile combined with the responses to past surveys represents a comprehensive view of changes in the industry.

  18. Mask Industry Assessment: 2010

    NASA Astrophysics Data System (ADS)

    Hughes, Greg; Chan, David Y.

    2010-09-01

    A survey created supported by SEMATECH and administered by David Powell Consulting was sent to microelectronics industry leaders to gather information about the mask industry as an objective assessment of its overall condition. The survey was designed with the input of semiconductor company mask technologists and merchant mask suppliers. This year's assessment is the ninth in the current series of annual reports. With ongoing industry support, the report can be used as a baseline to gain perspective on the technical and business status of the mask and microelectronics industries. It will continue to serve as a valuable reference to identify the strengths and opportunities of the mask industry. The results will be used to guide future investments pertaining to critical path issues. This year's survey was basically the same as the 2005 through 2009 surveys. Questions are grouped into categories: General Business Profile Information, Data Processing, Yields and Yield Loss Mechanisms, Delivery Times, Returns, and Services. Within each category are multiple questions that result in a detailed profile of both the business and technical status of the critical mask industry. This profile combined with the responses to past surveys represents a comprehensive view of changes in the industry.

  19. Industrial process surveillance system

    DOEpatents

    Gross, Kenneth C.; Wegerich, Stephan W.; Singer, Ralph M.; Mott, Jack E.

    1998-01-01

    A system and method for monitoring an industrial process and/or industrial data source. The system includes generating time varying data from industrial data sources, processing the data to obtain time correlation of the data, determining the range of data, determining learned states of normal operation and using these states to generate expected values, comparing the expected values to current actual values to identify a current state of the process closest to a learned, normal state; generating a set of modeled data, and processing the modeled data to identify a data pattern and generating an alarm upon detecting a deviation from normalcy.

  20. Industrial Process Surveillance System

    DOEpatents

    Gross, Kenneth C.; Wegerich, Stephan W; Singer, Ralph M.; Mott, Jack E.

    2001-01-30

    A system and method for monitoring an industrial process and/or industrial data source. The system includes generating time varying data from industrial data sources, processing the data to obtain time correlation of the data, determining the range of data, determining learned states of normal operation and using these states to generate expected values, comparing the expected values to current actual values to identify a current state of the process closest to a learned, normal state; generating a set of modeled data, and processing the modeled data to identify a data pattern and generating an alarm upon detecting a deviation from normalcy.

  1. Industrial process surveillance system

    DOEpatents

    Gross, K.C.; Wegerich, S.W.; Singer, R.M.; Mott, J.E.

    1998-06-09

    A system and method are disclosed for monitoring an industrial process and/or industrial data source. The system includes generating time varying data from industrial data sources, processing the data to obtain time correlation of the data, determining the range of data, determining learned states of normal operation and using these states to generate expected values, comparing the expected values to current actual values to identify a current state of the process closest to a learned, normal state; generating a set of modeled data, and processing the modeled data to identify a data pattern and generating an alarm upon detecting a deviation from normalcy. 96 figs.

  2. Automation of industrial bioprocesses.

    PubMed

    Beyeler, W; DaPra, E; Schneider, K

    2000-01-01

    The dramatic development of new electronic devices within the last 25 years has had a substantial influence on the control and automation of industrial bioprocesses. Within this short period of time the method of controlling industrial bioprocesses has changed completely. In this paper, the authors will use a practical approach focusing on the industrial applications of automation systems. From the early attempts to use computers for the automation of biotechnological processes up to the modern process automation systems some milestones are highlighted. Special attention is given to the influence of Standards and Guidelines on the development of automation systems.

  3. Alexandria (Al Iskandariya), Egypt

    NASA Technical Reports Server (NTRS)

    2002-01-01

    This image of Alexandria was taken by astronauts on board the International Space Station in December 2000 using an Electronic Still Camera. A wider-angle view (STS088-739-90) taken from the Space Shuttle in December 1998 is available for context. Alexandria (Al Iskandariya) occupies a T-shaped peninsula and strip of land separating the Mediterranean from Lake Mariout. Originally the town was built upon a mole (stone breakwater) called Heptastadium, which joined the island of Pharos (see referenced website, below) to the mainland. Since then sedimentary deposits have widened the mole. Since 1905, when the 370,000 Alexandrians lived in an area of about 4 sq km between the two harbors, the city (population 4 million; see referenced website, below) has grown beyond its medieval walls and now occupies an area of about 300 sq km. The Mahmudiya Canal, connecting Alexandria with the Nile, runs to the south of the city and, by a series of locks, enters the harbor of the principal port of Egypt (note ships). The reddish and ochre polygons west of Lake Mariout are salt-evaporation, chemical-storage, and water-treatment ponds within the coastal lagoon. Reference Youssef Halim and Fatma Abou Shouk, 2000, Human impacts on Alexandria's marine environment: UNESCO, Coastal Regions and Small Islands Unit (CSI), Coastal Management Sourcebooks 2 (accessed December 20, 2000) Additional photographs taken by astronauts can be viewed at NASA-JSC's Gateway to Astronaut Photography of Earth. Image ISS001-ESC-5025 provided by the Earth Sciences and Image Analysis Laboratory, Johnson Space Center.

  4. Computers Transform an Industry.

    ERIC Educational Resources Information Center

    Simich, Jack

    1982-01-01

    Describes the use of computer technology in the graphics communication industry. Areas that are examined include typesetting, color scanners, communications satellites, page make-up systems, and the business office. (CT)

  5. Lasers in food industry

    NASA Astrophysics Data System (ADS)

    Fyodorov, Boris F.

    1996-09-01

    Food industry had begun to use lasers for improvement of effectiveness of production. We can clearly see three main directions: in the food technology, in the food engineering, and in the agriculture. The results of the work is given.

  6. Industrial Assessment Center

    SciTech Connect

    J. Kelly Kissock; Becky Blust

    2007-04-17

    The University of Dayton (UD) performed energy assessments, trained students and supported USDOE objectives. In particular, the UD Industrial Assessment Center (IAC) performed 96 industrial energy assessment days for mid-sized manufacturers. The average identified and implemented savings on each assessment were $261,080 per year and $54,790 per year. The assessments served as direct training in industrial energy efficiency for 16 UD IAC students. The assessments also served as a mechanism for the UD IAC to understand manufacturing energy use and improve upon the science of manufacturing energy efficiency. Specific research results were published in 16 conference proceedings and journals, disseminated in 22 additional invited lectures, and shared with the industrial energy community through the UD IAC website.

  7. Uranium Industry Annual, 1992

    SciTech Connect

    Not Available

    1993-10-28

    The Uranium Industry Annual provides current statistical data on the US uranium industry for the Congress, Federal and State agencies, the uranium and electric utility industries, and the public. The feature article, ``Decommissioning of US Conventional Uranium Production Centers,`` is included. Data on uranium raw materials activities including exploration activities and expenditures, resources and reserves, mine production of uranium, production of uranium concentrate, and industry employment are presented in Chapter 1. Data on uranium marketing activities including domestic uranium purchases, commitments by utilities, procurement arrangements, uranium imports under purchase contracts and exports, deliveries to enrichment suppliers, inventories, secondary market activities, utility market requirements, and uranium for sale by domestic suppliers are presented in Chapter 2.

  8. The Educational Film Industry

    ERIC Educational Resources Information Center

    Tortora, Vincent R.; Schillaci, Peter

    1975-01-01

    Increased dialog is needed among educational film producers, distributors, and consumers in order to be sure that what is being produced meets educators' needs and also to help solve the financial problems of the film industry. (LS)

  9. Vocational/Industrial Arts.

    ERIC Educational Resources Information Center

    American School & University, 2002

    2002-01-01

    Describes the design of notable school vocational/industrial arts facilities, including the educational context and design goals. Includes information on architects, suppliers, and cost, as well as photographs. (EV)

  10. An Industrial Project

    ERIC Educational Resources Information Center

    Daniels, D. J.; And Others

    1975-01-01

    Describes the commercial uses, industrial production and laboratory production of 2-methylpentane-2,4-diol. Suggests extensions for the experiment in the areas of boiling point/composition curves and alkaline depolymerization. (GS)

  11. Report of the electrolytic industries for the year 1995

    SciTech Connect

    Pillay, G.; Chen, C.P.

    1996-10-01

    This report, sponsored by the Industrial Electrolysis and Electrochemical Engineering Division of The Electrochemical Society, summarizes published information on production, plant capacities, consumption, demand, trends, prices, raw materials, new technology, and environmental issues in the electrolytic and related industries. The material presented in this report was obtained form many sources and does not necessarily represent the opinion of the authors or their employers. The raw materials covered include Al, Be, Cr, Cu, Li, Mg, Mn, Ni, Ti, and Zn. The paper also covers batteries and electric vehicles, the electric utility industry, fuel cells, and environmental applications of electrochemistry. 239 refs.

  12. Industrial Fuel Flexibility Workshop

    SciTech Connect

    none,

    2006-09-01

    On September 28, 2006, in Washington, DC, ITP and Booz Allen Hamilton conducted a fuel flexibility workshop with attendance from various stakeholder groups. Workshop participants included representatives from the petrochemical, refining, food and beverage, steel and metals, pulp and paper, cement and glass manufacturing industries; as well as representatives from industrial boiler manufacturers, technology providers, energy and waste service providers, the federal government and national laboratories, and developers and financiers.

  13. Industrial waste pollution

    NASA Technical Reports Server (NTRS)

    Jensen, L. D.

    1972-01-01

    The characteristics and effects of industrial waste pollution in the Chesapeake Bay are discussed. The sources of inorganic and organic pollution entering the bay are described. The four types of pollutants are defined as: (1) inorganic chemical wastes, (2) naturally occurring organic wastes, (3) synthetic organic wastes (exotics) and (4) thermal effluents. The ecological behavior of industrial wastes in the surface waters is analyzed with respect to surface film phenomena, interfacial phenomena, and benthis phenomena

  14. Commentary on industrial processes.

    PubMed

    Hutchings, G J

    2005-04-15

    A brief commentary on the three papers presented in the session on 'industrial processes' is presented. In particular, emphasis is placed on the factors considered to be crucial for an industrial process, namely: catalyst activity, the selectivity of the overall catalysed reaction and the lifetime over which the performance is observed. Control of selectivity is viewed as being most important, and examples of how this is achieved through the use of membrane reactors and catalyst design are described.

  15. Ethics and Industrial Production

    NASA Astrophysics Data System (ADS)

    Bernard, Daniel

    The development of nanotechnology seems inevitable, for it alone would be able to solve or circumvent the huge difficulties to be faced by industrial and post-industrial societies, in both their private and their public aspects, and including the ageing population and its expectations with regard to health, the evolution of the climate, pollution, the management of food resources and raw materials, access to drinking water, control of energy production and consumption, equitable and sustainable development, etc.

  16. Thermal Modeling of Al-Al and Al-Steel Friction Stir Spot Welding

    NASA Astrophysics Data System (ADS)

    Jedrasiak, P.; Shercliff, H. R.; Reilly, A.; McShane, G. J.; Chen, Y. C.; Wang, L.; Robson, J.; Prangnell, P.

    2016-07-01

    This paper presents a finite element thermal model for similar and dissimilar alloy friction stir spot welding (FSSW). The model is calibrated and validated using instrumented lap joints in Al-Al and Al-Fe automotive sheet alloys. The model successfully predicts the thermal histories for a range of process conditions. The resulting temperature histories are used to predict the growth of intermetallic phases at the interface in Al-Fe welds. Temperature predictions were used to study the evolution of hardness of a precipitation-hardened aluminum alloy during post-weld aging after FSSW.

  17. Thermal Modeling of Al-Al and Al-Steel Friction Stir Spot Welding

    NASA Astrophysics Data System (ADS)

    Jedrasiak, P.; Shercliff, H. R.; Reilly, A.; McShane, G. J.; Chen, Y. C.; Wang, L.; Robson, J.; Prangnell, P.

    2016-09-01

    This paper presents a finite element thermal model for similar and dissimilar alloy friction stir spot welding (FSSW). The model is calibrated and validated using instrumented lap joints in Al-Al and Al-Fe automotive sheet alloys. The model successfully predicts the thermal histories for a range of process conditions. The resulting temperature histories are used to predict the growth of intermetallic phases at the interface in Al-Fe welds. Temperature predictions were used to study the evolution of hardness of a precipitation-hardened aluminum alloy during post-weld aging after FSSW.

  18. Joint effect of scandium and zirconium on the structure and the strength properties of Al-Mg2Si-Based alloys

    NASA Astrophysics Data System (ADS)

    Rokhlin, L. L.; Bochvar, N. R.; Tarytina, I. E.

    2015-09-01

    The joint effect of scandium and zirconium on the strength properties and the electrical resistivity of industrial Al-Mg2Si-based alloys has been studied. The additional alloying of Al-Mg2Si alloys with transition metals leads to substantial grain refinement of the aluminum solid-solution and, therefore, an increase in the strength properties of the industrial alloys.

  19. The Effects of Industrial Wastes of Memphis and Shelby County on Primary Planktonic Producers

    ERIC Educational Resources Information Center

    Staub, R.; And Others

    1970-01-01

    Diversity and total numbers of plankton, particularly diatoms, were analyzed and correlated with physical factors of water. Diversity index values appear to provide an indication of pollution of water by industrial and domestic wastes. (AL)

  20. Philosophieren als Unterrichtsprinzip im Mathematikunterricht

    NASA Astrophysics Data System (ADS)

    Meerwaldt, Diana

    Philosophieren und Mathematik scheinen zunächst gegensätzliche Bereiche zu sein, die sich kaum vereinbaren lassen. Dies trifft für eine Auffassung zu, die Philosophieren als "Gerede" disqualifiziert und Mathematik als eine reine "Formelwissenschaft" begreift. Beide Auffassungen werden den Gegenständen nicht gerecht.

  1. Enhanced hardness in epitaxial TiAlScN alloy thin films and rocksalt TiN/(Al,Sc)N superlattices

    SciTech Connect

    Saha, Bivas; Lawrence, Samantha K.; Bahr, David F.; Schroeder, Jeremy L.; Birch, Jens; Sands, Timothy D.

    2014-10-13

    High hardness TiAlN alloys for wear-resistant coatings exhibit limited lifetimes at elevated temperatures due to a cubic-AlN to hexagonal-AlN phase transformation that leads to decreasing hardness. We enhance the hardness (up to 46 GPa) and maximum operating temperature (up to 1050 °C) of TiAlN-based coatings by alloying with scandium nitride to form both an epitaxial TiAlScN alloy film and epitaxial rocksalt TiN/(Al,Sc)N superlattices on MgO substrates. The superlattice hardness increases with decreasing period thickness, which is understood by the Orowan bowing mechanism of the confined layer slip model. These results make them worthy of additional research for industrial coating applications.

  2. Assessment of the Heavy Metals in Al Asfar Lake, Al-Hassa, Saudi Arabia.

    PubMed

    Hussein, Adel H A; El Mahmoudi, Ahmed S; Al Naeem, Ahmed A

    2016-02-01

    Al Asfar Lake is a shallow wetland and habitat for wildlife and birds in a desert environment. The water of this lake is originated from the drainage water collected by earthen drainage network and discharged into the lake. The purpose of this study was to assess physico- chemical characteristics and some of heavy metals in Al Asfar lake water. The studied parameters are iron, manganese, copper, zinc, cadmium, chromium, lead, pH, electrical conductivity, and nitrate. Forty-five surface water samples were collected in March 2013. The results revealed that the pH ranged from 7.33 to 8.67, electrical conductivity ranged from 8.28 to 11.34 dS/m, and NO(3)(-) ranged from 0.84 to 2.29 mg/L. In addition, heavy metals concentrations in water were found in the following order: Fe > Mn > Cu > Zn > Cd > Cr = Pb. The mean concentrations of heavy metals in surface water of Al Asfar lake ranged from 0.027 to 0.159 ppm, 0.007 to 0.142 ppm, 0.005 to 0.017 ppm, 0.005 to 0.066 ppm, 0.001 to 0.033 ppm, 0 ppm, and 0 ppm for iron, manganese, copper, zinc, cadmium, chromium, and lead, respectively. Moreover, pH, NO(3)(-), Fe, Mn, and Zn concentrations in the surface water of Al Asfar Lake were found to be within the international permissible limits. On the other hand, Cu and Cd concentrations exceeded the international permissible limits. The high level of some parameters of the measured heavy metals could be attributed to the contamination of Al Asfar Lake with discharge water enriched with chemical fertilizers in addition to domestic and industrial effluents. PMID:26803101

  3. Chemical Educators Stress Industry Ties

    ERIC Educational Resources Information Center

    Worthy, Ward

    1975-01-01

    Describes various courses and programs designed to better prepare graduates to enter the chemical industry, including courses which stress the chemistry of industrial processes, and the economics of the chemical industry. (MLH)

  4. Alloy development and processing of FeAl: An overview

    SciTech Connect

    Maziasz, P.J.; Goodwin, G.M.; Alexander, D.J.; Viswanathan, S.

    1997-03-01

    In the last few years, considerable progress has been made in developing B2-phase FeAl alloys with improved weldability, room-temperature ductility, and high-temperature strength. Controlling the processing-induced microstructure is also important, particularly for minimizing trade-offs in various properties. FeAl alloys have outstanding resistance to high-temperature oxidation, sulfidation, and corrosion in various kinds of molten salts due to formation of protective Al{sub 2}O{sub 3} scales. Recent work shows that FeAl alloys are carburization-resistant as well. Alloys with 36 to 40 at. % Al have the best combination of corrosion resistance and mechanical properties. Minor alloying additions of Mo, Zr, and C, together with microalloying additions of B, produce the best combination of weldability and mechanical behavior. Cast FeAl alloys, with 200 to 400 {mu}m grain size and finely dispersed ZrC, have 2 to 5% tensile ductility in air at room-temperature, and a yield strength > 400 MPa up to about 700 to 750{degrees}C. Extruded ingot metallurgy (I/M) and powder metallurgy (P/M) materials with refined grain sizes ranging from 2 to 50 {mu}m, can have 10 to 15% ductility in air and be much stronger, and can even be quite tough, with Charpy impact energies ranging from 25 to 105 J at room-temperature. This paper highlights progress made in refining the alloy composition and exploring processing effects on FeAl for monolithic applications. It also includes recent progress on developing FeAl weld-overlay technology, and new results on welding of FeAl alloys. It summarizes some of the current industrial testing and interest for applications.

  5. The Advanced Launch System (ALS)

    NASA Astrophysics Data System (ADS)

    Eldred, Charles H.

    The Advanced Launch System (ALS) is an unmanned vehicle that will achieve low hardware cost by using a reusable booster stage which flies back to the launch site, and a core stage in which the rocket engines and redundant avionics are in a module that is returned to earth and recovered for reuse. The booster's utilization of liquid propellant instead of solid propellant will help lower the consumable costs. The ALS also includes launch processing and flight control facilities, necessary support equipment, and ground- and flight-operations infrastructure. The ALS program studies show that, through the ALS, the United States can launch a major Mars initiative economically and with confidence. It is estimated that the objective ALS can be operational in the late 1990s.

  6. AERIAL VIEW OF SLOSS INDUSTRIES, COKE WORKS IN NORTH BIRMINGHAM, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    AERIAL VIEW OF SLOSS INDUSTRIES, COKE WORKS IN NORTH BIRMINGHAM, VIEW LOOKING SOUTH TOWARD BIRMINGHAM CITY CENTER (SKYSCRAPERS IN FAR DISTANCE RIGHT) AND ACROSS COLLEGEVILLE (BETHEL BAPTIST CHURCH) & NORWOOD RESIDENTIAL DISTRICTS. - Sloss Sheffield Steel & Iron Company, 3500 Thirty-fifth Avenue North, Birmingham, Jefferson County, AL

  7. NEMS industrial module documentation report

    SciTech Connect

    Not Available

    1994-01-01

    The NEMS Industrial Demand Model is a dynamic accounting model, bringing together the disparate industries and uses of energy in those industries, and putting them together in an understandable and cohesive framework. The Industrial Model generates mid-term (up to the year 2010) forecasts of industrial sector energy demand as a component of the NEMS integrated forecasting system. From the NEMS system, the Industrial Model receives fuel prices, employment data, and the value of output of industrial activity. Based on the values of these variables, the Industrial Model passes back to the NEMS system estimates of consumption by fuel types.

  8. Wetting and strength issues at Al/alpha-alumina interfaces

    SciTech Connect

    Saiz, Eduardo; Tomsia, Antoni P.; Suganuma, Katsuaki

    2003-04-15

    The wetting behavior and strength at aluminum/alumina interfaces has been an active subject of research. Al/alumina applications include ceramic-metal composites and several applications for electronic industries. In this paper the interface strength and microstructure of Al/alpha-alumina was investigated. We discovered that in a solid-state joining, the strength of the joint increases with increasing joining temperature. In a liquid-state joining, the strength of the joint gradually decreases due to the formation of unbonded areas. The strength, sigma sub b, is expressed by the following equation as a function of unbonded area, A: sigma sub b = 2.22 A + 143 (70 percent {le} A {le} 100 percent). The highest strength reached 400 MPa when the interface was formed at around the melting temperature of aluminum. An aluminum layer close to the interface became a single crystal when it was bonded to a sapphire. The following crystallographic orientation relationship is established: (1{bar 1}1){sub Al}//(001){sub {alpha}}-Al{sub 2} O{sub 3}, (110){sub Al}//<100>{sub {alpha}}-Al{sub 2}O{sub 3}. Amorphous alumina islands were formed at the interface. In the amorphous alumina, gamma-alumina nanocrystals grew from the sapphire, with the same orientation relationship to sapphire as above.

  9. Quantum dots formed in InSb/AlAs and AlSb/AlAs heterostructures

    NASA Astrophysics Data System (ADS)

    Abramkin, D. S.; Rumynin, K. M.; Bakarov, A. K.; Kolotovkina, D. A.; Gutakovskii, A. K.; Shamirzaev, T. S.

    2016-06-01

    The crystal structure of new self-assembled InSb/AlAs and AlSb/AlAs quantum dots grown by molecularbeam epitaxy has been investigated by transmission electron microscopy. The theoretical calculations of the energy spectrum of the quantum dots have been supplemented by the experimental data on the steady-state and time-resolved photoluminescence spectroscopy. Deposition of 1.5 ML of InSb or AlSb on the AlAs surface carried out in the regime of atomic-layer epitaxy leads to the formation of pseudomorphically strained quantum dots composed of InAlSbAs and AlSbAs alloys, respectively. The quantum dots can have the type-I and type-II energy spectra depending on the composition of the alloy. The ground hole state in the quantum dot belongs to the heavy-hole band and the localization energy of holes is much higher than that of electrons. The ground electron state in the type-I quantum dots belongs to the indirect X XY valley of the conduction band of the alloy. The ground electron state in the type-II quantum dots belongs to the indirect X valley of the conduction band of the AlAs matrix.

  10. Industrial Section Convenor's Report

    NASA Astrophysics Data System (ADS)

    Barone, M.; Riboni, P.

    2002-11-01

    Over the years this conference has gained a solid reputation as an appropriate rostrum for illustrating new concepts in the relations between industry and the scientific world and for introducing new technologies to a large assistance of junior and more experienced scientists. In fact, from the very beginning the founders of this endeavour announced: "The conference is aimed for promoting contacts among scientists involved in particle and fundamental physics, among experimental physicists in other fields and representatives from industry." Facilities at the Conference are designed to fulfil the task: space and general facilities are offered to industry representatives to display their products. This year a more accessible and luminous space arrangement was made available to the exhibitors. At the same time two plenary sessions have been dedicated to selected speakers to illustrate new trends in Technology Transfer, analysis of environment affecting our community, examples of historical successes in the merging of science and industry. We have identified in "GRID" and in "E-Publishing" two major promising areas where our Community will play a prime role as "User" and it was of the general interest to have them illustrated by two personalities directly involved in their development. The flow of knowledge is of course more massive from "Industry" to "Science" than vice-versa, but "Science" to "Industry" move offers an intensive added value. The technology transfer concept with the "Patents" as fund raising tool proved less glorious than expected. Trademark, licensing agreement and " Patents" can assure intellectual properties. But patent is an issue to be used cautiously. Evidence exists that much more efficient transfer of "Science" knowledge to "Economy" is achieved by venture capital move and start-up companies. These two facets of the Technology Transfer business have been covered by Routti's and Bourgeois's lectures.There are two examples of Companies who moved

  11. Quantic Industries Inc. slapper detonator performance

    SciTech Connect

    Cutting, J.L.; Lee, R.S.; Hodgin, R.L.

    1994-05-01

    Under the Lawrence Livermore National Laboratories (LLNL) Small Business Technology Transfer Program, assistance was given to Quantic Industries Inc. to use the High Explosive Applications Facility (HEAF), its apparatus, and LLNL expertise to characterize the performance of Quantic`s micro-clad copper/kapton slapper detonator assemblies and establish their threshold to detonate HNS-IV. The project involved measuring the performance of these slapper detonators, otherwise known as Exploding Foil Initiators (EFI`s), manufactured by Quantic Industries Inc. Slapper performance was measured by using a laser velocimeter, which is an expensive and specialized facility which Quantic does not own. The authors measured slapper velocity vs. time as a function of charging voltage. Quantic supplied slappers which were coated with {approximately}100 nm of Al to provide a reflective surface for the laser velocimeter measurements. LLNL provided to a capacitor discharge unit (CDU) to fire the slappers and matched the Quantic CDU waveforms as close as possible.

  12. Lightweight Steel Solutions for Automotive Industry

    SciTech Connect

    Lee, Hong Woo; Kim, Gyosung; Park, Sung Ho

    2010-06-15

    Recently, improvement in fuel efficiency and safety has become the biggest issue in worldwide automotive industry. Although the regulation of environment and safety has been tightened up more and more, the majority of vehicle bodies are still manufactured from stamped steel components. This means that the optimized steel solutions enable to demonstrate its ability to reduce body weight with high crashworthiness performance instead of expensive light weight materials such as Al, Mg and composites. To provide the innovative steel solutions for automotive industry, POSCO has developed AHSS and its application technologies, which is directly connected to EVI activities. EVI is a technical cooperation program with customer covering all stages of new car project from design to mass production. Integrated light weight solutions through new forming technologies such as TWB, hydroforming and HPF are continuously developed and provided for EVI activities. This paper will discuss the detailed status of these technologies especially light weight steel solutions based on innovative technologies.

  13. Lightweight Steel Solutions for Automotive Industry

    NASA Astrophysics Data System (ADS)

    Lee, Hong Woo; Kim, Gyosung; Park, Sung Ho

    2010-06-01

    Recently, improvement in fuel efficiency and safety has become the biggest issue in worldwide automotive industry. Although the regulation of environment and safety has been tightened up more and more, the majority of vehicle bodies are still manufactured from stamped steel components. This means that the optimized steel solutions enable to demonstrate its ability to reduce body weight with high crashworthiness performance instead of expensive light weight materials such as Al, Mg and composites. To provide the innovative steel solutions for automotive industry, POSCO has developed AHSS and its application technologies, which is directly connected to EVI activities. EVI is a technical cooperation program with customer covering all stages of new car project from design to mass production. Integrated light weight solutions through new forming technologies such as TWB, hydroforming and HPF are continuously developed and provided for EVI activities. This paper will discuss the detailed status of these technologies especially light weight steel solutions based on innovative technologies.

  14. The international electronics industry.

    PubMed

    LaDou, J; Rohm, T

    1998-01-01

    High-technology microelectronics has a major presence in countries such as China, India, Indonesia, and Malaysia, now the third-largest manufacturer of semiconductor chips. The migration of European, Japanese, and American companies accommodates regional markets. Low wage rates and limited enforcement of environmental regulations in developing countries also serve as incentives for the dramatic global migration of this industry. The manufacture of microelectonics products is accompanied by a high incidence of occupational illnesses, which may reflect the widespread use of toxic materials. Metals, photoactive chemicals, solvents, acids, and toxic gases are used in a wide variety of combinations and workplace settings. The industry also presents problems of radiation exposure and various occupational stressors, including some unresolved ergonomic issues. The fast-paced changes of the technology underlying this industry, as well as the stringent security precautions, have added to the difficulty of instituting proper health and safety measures. Epidemiologic studies reveal an alarming increase in spontaneous abortions among cleanroom manufacturing workers; no definitive study has yet identified its cause. Other health issues, including occupational cancer, are yet to be studied. The microelectronics industry is a good example of an industry that is exported to many areas of the world before health and safety problems are properly addressed and resolved. PMID:10026464

  15. The international electronics industry.

    PubMed

    LaDou, J; Rohm, T

    1998-01-01

    High-technology microelectronics has a major presence in countries such as China, India, Indonesia, and Malaysia, now the third-largest manufacturer of semiconductor chips. The migration of European, Japanese, and American companies accommodates regional markets. Low wage rates and limited enforcement of environmental regulations in developing countries also serve as incentives for the dramatic global migration of this industry. The manufacture of microelectonics products is accompanied by a high incidence of occupational illnesses, which may reflect the widespread use of toxic materials. Metals, photoactive chemicals, solvents, acids, and toxic gases are used in a wide variety of combinations and workplace settings. The industry also presents problems of radiation exposure and various occupational stressors, including some unresolved ergonomic issues. The fast-paced changes of the technology underlying this industry, as well as the stringent security precautions, have added to the difficulty of instituting proper health and safety measures. Epidemiologic studies reveal an alarming increase in spontaneous abortions among cleanroom manufacturing workers; no definitive study has yet identified its cause. Other health issues, including occupational cancer, are yet to be studied. The microelectronics industry is a good example of an industry that is exported to many areas of the world before health and safety problems are properly addressed and resolved.

  16. Medical application of 26Al

    NASA Astrophysics Data System (ADS)

    Steinhausen, C.; Gerisch, P.; Heisinger, B.; Hohl, Ch.; Kislinger, G.; Korschinek, G.; Niedermayer, M.; Nolte, E.; Dumitru, M.; Alvarez-Brückmann, M.; Schneider, M.; Ittel, T. H.

    1996-06-01

    Accelerator mass spectrometry (AMS) measurements with 26Al as tracer were performed in order to study the aluminium metabolism and anomalies in the human body and in rats. In particular, the differences between healthy volunteers and patients with renal failure were investigated. The obtained data points of 26Al in blood and urine were described by an open compartment model with three peripheral compartments. It was found that the minimum of peripheral compartments needed to describe 26Al concentrations in blood and urine over a time period of three years is at least three.

  17. Air stripping industrial wastewater

    SciTech Connect

    Lamarre, B.; Shearouse, D.

    1994-09-01

    Industrial wastewater can be quickly, efficiently and economically treated using air strippers. Air stripping removes a range of volatile and semi-volatile contaminants from water. And the performance of various types and sizes of tray-type air stripper for treating contaminated water now is highly predictable because of laboratory studies. Air stripping can be a fast, efficient and economical approach to treating industrial wastewater. However, since every industrial wastewater stream is unique, each must be evaluated to determine its constituents, its potentially adverse effects on treatability, and any pretreatment steps necessary to ensure desired results. The general principles of air stripping are simple. In an air stripper, the surfaces area of a film of contaminated water is maximized while air is directed across it. Contaminants at the air/water interface volatilize and are discharged to the atmosphere or to an off-gas treatment system.

  18. The international petrochemical industry

    SciTech Connect

    Chapman, K.

    1991-01-01

    The petrochemical industry occupies a crucial place in economic, strategic and political terms in the twentieth century. The author explains its growth and international distribution from the 1920s tot he present, relating the particular experience of petrochemicals to the processes that have shaped the long-term evolution of industry in general. The geographical coverage of this book extends from the regional to international scale, and its historical scope embraces one hundred years from the laboratory origins of polymer science and petrochemistry to the massive operations of modern industry. It represents the result of twenty years of research, and reflects the author's privileged access to company sources in both the U.S. and Europe.

  19. [[Population and industrial development

    PubMed

    Charoenloet, V

    "Concurrent with the decline in population growth rate in the 1980s, Thailand experienced an unprecedented rate of economic growth....Such phenomenal economic growth has generally been attributed to the internationalization of the Thai economy through the rapid expansion of exports, foreign investment and tourism. However, industries in the manufacturing sector...tend to be resource-based and labour-intensive. Moreover, foreign investment in export-oriented industries tends to use Thailand as a base for assembling rather than producing goods and has been attracted primarily by cheap labour cost. All these may contribute to the employment of [a] nonskilled, lowly-paid labour force, but not the development of scientific/technology based industries, the foundation for permanent and lasting economic development." (SUMMARY IN ENG)

  20. Industrial Code Development

    NASA Technical Reports Server (NTRS)

    Shapiro, Wilbur

    1991-01-01

    The industrial codes will consist of modules of 2-D and simplified 2-D or 1-D codes, intended for expeditious parametric studies, analysis, and design of a wide variety of seals. Integration into a unified system is accomplished by the industrial Knowledge Based System (KBS), which will also provide user friendly interaction, contact sensitive and hypertext help, design guidance, and an expandable database. The types of analysis to be included with the industrial codes are interfacial performance (leakage, load, stiffness, friction losses, etc.), thermoelastic distortions, and dynamic response to rotor excursions. The first three codes to be completed and which are presently being incorporated into the KBS are the incompressible cylindrical code, ICYL, and the compressible cylindrical code, GCYL.

  1. Industrial Assessment Center Program

    SciTech Connect

    Dr. Dereje Agonafer

    2007-11-30

    The work described in this report was performed under the direction of the Industrial Assessment Center (IAC) at University of Texas at Arlington. The IAC at The University of Texas at Arlington is managed by Rutgers University under agreement with the United States Department of Energy Office of Industrial Technology, which financially supports the program. The objective of the IAC is to identify, evaluate, and recommend, through analysis of an industrial plant’s operations, opportunities to conserve energy and prevent pollution, thereby reducing the associated costs. IAC team members visit and survey the plant. Based upon observations made in the plant, preventive/corrective actions are recommended. At all times we try to offer specific and quantitative recommendations of cost savings, energy conservation, and pollution prevention to the plants we serve.

  2. Pharmaceutical Industry in Syria

    PubMed Central

    2010-01-01

    The aim of this article is to present the development of the pharmaceutical industry in Syria using national and international public data sources. At the end of the 80ies, the pharmaceutical industry in Syria was very poor, covering 6% of the national needs. In less than 20 years, with the government support in terms of legal frame and strategic political engagement, the Syrian pharmaceutical industry finally covered almost 90% of the national needs, in terms of drugs, and exported drugs in around 52 Arabian countries. Beyond covering the local market, the main added values of this huge development consisted in exporting drugs in amount of 150 million dollars per year and providing jobs for 17000 Syrian people, out of which around 85% are women. Strong and weak points of the pharmaceutical sector are taken into consideration in the article and further interventions to support a sustainable development are proposed by the author. PMID:20945828

  3. Explosive Fabrication of Intermetallics In Ti-Al System from Nano-Al and Coarse-Ti Powders

    NASA Astrophysics Data System (ADS)

    Chikhradze, Mikheil; Gigineishvili, Akaki; Cikhradze, Nikoloz

    2011-12-01

    Theoretical and experimental Investigations of shock wave consolidation processes of Ti-Al nano sized and ultra-disperse powder compositions are discussed. For theoretical calculations of the shock wave loaded materials were used the hydrodynamic theory and experimental adiabatics of Ti and Al. The normal and tangential stresses in the cylindrical steel tube (containers of Ti-Al reaction mixtures) were estimated using the partial solutions of elasticity theory. The mixtures of ultra-disperse Ti and nano sized (max≤50 nm) Al powder compositions were consolidated to full or near-full density by explosive-compaction technology. The ammonium nitride based industrial explosives were used for generation of shock waves. To form ultra-fine grained bulk TiAl intermetallides with different compositions, ultra-disperse Ti particles were mixed with nano-crystalline Al. Each reaction mixture was placed in a sealed container and explosively compacted using a normal and cylindrical detonation set-up. Explosive compaction experiments were performed in range of pressure impulse (5-20 GPA) at elevated temperatures. X-ray diffraction (XRD), structural investigations (SEM) and micro-hardness measurements were used to characterize the intermetallides phase composition and mechanical properties. The results of analysis revealing the effects of the compacting conditions and precursor particles sizes, affecting the consolidation and the properties of this new ultra high performance alloys are discussed.

  4. Emulsified industrial oils recycling

    SciTech Connect

    Gabris, T.

    1982-04-01

    The industrial lubricant market has been analyzed with emphasis on current and/or developing recycling and re-refining technologies. This task has been performed for the United States and other industrialized countries, specifically France, West Germany, Italy and Japan. Attention has been focused at emulsion-type fluids regardless of the industrial application involved. It was found that emulsion-type fluids in the United States represent a much higher percentage of the total fluids used than in other industrialized countries. While recycling is an active matter explored by the industry, re-refining is rather a result of other issues than the mere fact that oil can be regenerated from a used industrial emulsion. To extend the longevity of an emulsion is a logical step to keep expenses down by using the emulsion as long as possible. There is, however, another important factor influencing this issue: regulations governing the disposal of such fluids. The ecological question, the respect for nature and the natural balances, is often seen now as everybody's task. Regulations forbid dumping used emulsions in the environment without prior treatment of the water phase and separation of the oil phase. This is a costly procedure, so recycling is attractive since it postpones the problem. It is questionable whether re-refining of these emulsions - as a business - could stand on its own if these emulsions did not have to be taken apart for disposal purposes. Once the emulsion is separated into a water and an oil phase, however, re-refining of the oil does become economical.

  5. Solar industrial process heat

    SciTech Connect

    Lumsdaine, E.

    1981-04-01

    The aim of the assessment reported is to candidly examine the contribution that solar industrial process heat (SIPH) is realistically able to make in the near and long-term energy futures of the United States. The performance history of government and privately funded SIPH demonstration programs, 15 of which are briefly summarized, and the present status of SIPH technology are discussed. The technical and performance characteristics of solar industrial process heat plants and equipment are reviewed, as well as evaluating how the operating experience of over a dozen SIPH demonstration projects is influencing institutional acceptance and economoc projections. Implications for domestic energy policy and international implications are briefly discussed. (LEW)

  6. From rumen to industry.

    PubMed

    Sauer, Michael; Marx, Hans; Mattanovich, Diethard

    2012-09-10

    The rumen is one of the most complicated and most fascinating microbial ecosystems in nature. A wide variety of microbial species, including bacteria, fungi and protozoa act together to bioconvert (ligno)cellulosic plant material into compounds, which can be taken up and metabolized by the ruminant. Thus, the rumen perfectly resembles a solution to a current industrial problem: the biorefinery, which aims at the bioconversion of lignocellulosic material into fuels and chemicals. We suggest to intensify the studies of the ruminal microbial ecosystem from an industrial microbiologists point of view in order to make use of this rich source of organisms and enzymes.

  7. Industrial sand and gravel

    USGS Publications Warehouse

    Dolley, T.P.

    2010-01-01

    Domestic production of industrial sand and gravel in 2009 was about 27 Mt (30 million st), declining by 10 percent compared with 2008. Certain end uses of industrial sand and gravel, such as foundry and glassmaking sand, may have declined by a factor greater than 10 percent in 2009. U.S. apparent consumption was 24.7 Mt (27.2 million st) in 2009, down by 10 percent from the previous year, and imports declined to 83 kt (91,000 st).

  8. US industrial battery forecast

    SciTech Connect

    Hollingsworth, V. III

    1996-09-01

    Last year was strong year for the US industrial battery market with growth in all segments. Sales of industrial batteries in North America grew 19.2% in 1995, exceeding last year`s forecasted growth rate of 11.6%. The results of the recently completed BCI Membership Survey forecast 1996 sales to be up 10.5%, and to continue to increase at a 10.4% compound annual rate through the year 2000. This year`s survey includes further detail on the stationary battery market with the inclusion of less than 25 Ampere-Hour batteries for the first time.

  9. INDUSTRIAL ASSESSMENT CENTER PROGRAM

    SciTech Connect

    ASFAW BEYENE

    2008-09-29

    Since its establishment in 1990, San Diego State University’s Industrial Assessment Center (IAC) has served close to 400 small and medium-sized manufacturing plants in Southern California. SDSU/IAC’s efforts to transfer state-of-the-art technologies to industry have increased revenues, cultivated creativity, improved efficiencies, and benefited the environment. A substantial benefit from the program has been the ongoing training of engineering faculty and students. During this funding cycle, SDSU/IAC has trained 31 students, 7 of the graduate. A total of 92 assessments and 108 assessment days were completed, resulting in 638 assessment recommendations.

  10. Transferring Technology to Industry

    NASA Technical Reports Server (NTRS)

    Wolfenbarger, J. Ken

    2006-01-01

    This slide presentation reviews the technology transfer processes in which JPL has been involved to assist in transferring the technology derived from aerospace research and development to industry. California Institute of Technology (CalTech), the organization that runs JPL, is the leading institute in patents for all U.S. universities. There are several mechanisms that are available to JPL to inform industry of these technological advances: (1) a dedicated organization at JPL, National Space Technology Applications (NSTA), (2) Tech Brief Magazine, (3) Spinoff magazine, and (4) JPL publications. There have also been many start-up organizations and businesses from CalTech.

  11. Lattice stabilities, mechanical and thermodynamic properties of Al3Tm and Al3Lu intermetallics under high pressure from first-principles calculations

    NASA Astrophysics Data System (ADS)

    Xu-Dong, Zhang; Wei, Jiang

    2016-02-01

    The effects of high pressure on lattice stability, mechanical and thermodynamic properties of L12 structure Al3Tm and Al3Lu are studied by first-principles calculations within the VASP code. The phonon dispersion curves and density of phonon states are calculated by using the PHONONPY code. Our results agree well with the available experimental and theoretical values. The vibrational properties indicate that Al3Tm and Al3Lu keep their dynamical stabilities in L12 structure up to 100 GPa. The elastic properties and Debye temperatures for Al3Tm and Al3Lu increase with the increase of pressure. The mechanical anisotropic properties are discussed by using anisotropic indices AG, AU, AZ, and the three-dimensional (3D) curved surface of Young’s modulus. The calculated results show that Al3Tm and Al3Lu are both isotropic at 0 GPa and anisotropic under high pressure. In the present work, the sound velocities in different directions for Al3Tm and Al3Lu are also predicted under high pressure. We also calculate the thermodynamic properties and provide the relationships between thermal parameters and temperature/pressure. These results can provide theoretical support for further experimental work and industrial applications. Project supported by the Scientific Technology Plan of the Educational Department of Liaoning Province and Liaoning Innovative Research Team in University, China (Grant No. LT2014004) and the Program for the Young Teacher Cultivation Fund of Shenyang University of Technology, China (Grant No. 005612).

  12. Nucleation and Growth of Cu-Al Intermetallics in Al-Modified Sn-Cu and Sn-Ag-Cu Lead-Free Solder Alloys

    NASA Astrophysics Data System (ADS)

    Reeve, Kathlene N.; Anderson, Iver E.; Handwerker, Carol A.

    2015-03-01

    Lead-free solder alloys Sn-Cu (SC) and Sn-Ag-Cu (SAC) are widely used by the microelectronics industry, but enhanced control of the microstructure is needed to improve solder performance. For such control, nucleation and stability of Cu-Al intermetallic compound (IMC) solidification catalysts were investigated by variation of the Cu (0.7-3.0 wt.%) and Al (0.0-0.4 wt.%) content of SC + Al and SAC + Al alloys, and of SAC + Al ball-grid array (BGA) solder joints. All of the Al-modified alloys produced Cu-Al IMC particles with different morphologies and phases (occasionally non-equilibrium phases). A trend of increasing Cu-Al IMC volume fraction with increasing Al content was established. Because of solidification of non-equilibrium phases in wire alloy structures, differential scanning calorimetry (DSC) experiments revealed delayed, non-equilibrium melting at high temperatures related to quenched-in Cu-Al phases; a final liquidus of 960-1200°C was recorded. During cooling from 1200°C, the DSC samples had the solidification behavior expected from thermodynamic equilibrium calculations. Solidification of the ternary alloys commenced with formation of ternary β and Cu-Al δ phases at 450-550°C; this was followed by β-Sn, and, finally, Cu6Sn5 and Cu-Al γ1. Because of the presence of the retained, high-temperature phases in the alloys, particle size and volume fraction of the room temperature Cu-Al IMC phases were observed to increase when the alloy casting temperature was reduced from 1200°C to 800°C, even though both temperatures are above the calculated liquidus temperature of the alloys. Preliminary electron backscatter diffraction results seemed to show Sn grain refinement in the SAC + Al BGA alloy.

  13. In memory of Al Cameron

    NASA Astrophysics Data System (ADS)

    Cowan, John; Truran, James W.

    Al Cameron, who died recently (October 3, 2005) at 80, was one of the giants in astrophysics. His insights were profound and his interests were wide-ranging. Originally trained as a nuclear physicist, he made major contributions in a number of fields, including nuclear reactions in stars, nucleosynthesis, the abundances of the elements in the Solar System, and the origin of the Solar System and the Moon. In 1957, Cameron and, independently, Burbidge, Burbidge, Fowler and Hoyle, wrote seminal papers on nuclear astrophysics. Most of our current ideas concerning ele- ment formation in stars have followed from those two pioneering and historical works. Al also made many contributions in the field of Solar System physics. Particularly noteworthy in this regard was Cameron's work on the formation of the Moon. Al was also a good friend and mentor of young people. Al Cameron will be missed by many in the community both for his scientific contributions and for his friendship.

  14. Frontiers in Industrial Arts Education.

    ERIC Educational Resources Information Center

    MacDonnell, Elisabeth, Ed.; Strosnider, Floy, Ed.

    Presentation topics of the 28th annual American Industrial Arts Association Convention include: (1) "Where We Are in Federal Legislation Programs," (2) "Frontiers in Industrial Arts Education," and (3) "Industry's Cooperation with Education." Eleven symposia were conducted on the topic of "Implementing Frontier Ideas in Industrial Arts Education…

  15. Burlington Industries: Modernize or Perish

    ERIC Educational Resources Information Center

    Honeycutt, Earl D., Jr.

    2013-01-01

    In the 1960s, Burlington Industries was the largest textile firm in the world, and in 1973 the U. S. textile industry employed more than 1 million workers. Dynamic change came to the textile industry beginning in the 1960s, and in 2001 Burlington Industries filed for Chapter 11 bankruptcy. This case traces the dynamics of the market and the…

  16. Commercial and Industrial Wiring.

    ERIC Educational Resources Information Center

    Kaltwasser, Stan; Flowers, Gary

    This module is the third in a series of three wiring publications, includes additional technical knowledge and applications required for job entry in the commercial and industrial wiring trade. The module contains 15 instructional units that cover the following topics: blueprint reading and load calculations; tools and equipment; service;…

  17. Lasers in food industry

    NASA Astrophysics Data System (ADS)

    Fyodorov, Boris F.

    1996-12-01

    The food industry has begun using lasers for improving the effectiveness of production. We clearly see three main directions: in food technology, in food engineering, and in agriculture. The resulting work of the seminar with concrete results, gotten by some research centers, is given. The programs of the seminar for 1988-1996 also are given.

  18. 2012 Mask Industry Survey

    NASA Astrophysics Data System (ADS)

    Malloy, Matt; Litt, Lloyd C.

    2012-11-01

    A survey supported by SEMATECH and administered by David Powell Consulting was sent to semiconductor industry leaders to gather information about the mask industry as an objective assessment of its overall condition. The survey was designed with the input of semiconductor company mask technologists and merchant mask suppliers. 2012 marks the 11th consecutive year for the mask industry survey. This year's survey and reporting structure are similar to those of the previous years with minor modifications based on feedback from past years and the need to collect additional data on key topics. Categories include general mask information, mask processing, data and write time, yield and yield loss, delivery times, and maintenance and returns. Within each category are multiple questions that result in a detailed profile of both the business and technical status of the mask industry. Results, initial observations, and key comparisons between the 2011 and 2012 survey responses are shown here, including multiple indications of a shift towards the manufacturing of higher end photomasks.

  19. Air Pollution and Industry.

    ERIC Educational Resources Information Center

    Ross, R. D., Ed.

    This book is an authoritative reference and practical guide designed to help the plant engineer identify and solve industrial air pollution problems in order to be able to meet current air pollution regulations. Prepared under the editorial supervision of an experienced chemical engineer, with each chapter contributed by an expert in his field,…

  20. Industrial Radiography Manual.

    ERIC Educational Resources Information Center

    Richardson, Harry D.

    This text was developed for use by students in an 80-hour course for industrial radiographers. Chapter headings are: (1) The Structure of Matter, (2) Radiation and Radiation Machines, (3) Nuclear Reactions and Radioisotopes, (4) Interaction of Radiation with Matter, (5) Radiation Detection and Measurement, (6) The Nature and Consequences of…

  1. University-industry interaction

    NASA Technical Reports Server (NTRS)

    Hastings, Daniel E.

    1990-01-01

    It is posited that university industry interaction is highly desirable from the viewpoint of the long term economic development of the country as well as being desirable for the Space Grant Programs. The present and future possible interactions are reviewed for the three university levels namely, undergraduate, graduate, and faculty research.

  2. Petroleum industry in Iran

    SciTech Connect

    Farideh, A.

    1981-01-01

    This study examines the oil industry in Iran from the early discovery of oil nearly two hundred years ago in Mazandaran (north part) to the development of a giant modern industry in the twentieth century. Chapter I presents a brief historical setting to introduce the reader to the importance of oil in Iran. It focuses on the economic implications of the early oil concessions in the period 1901 to 1951. Chapter II discusses the nationalization of the Iranian oil industry and creation of NIOC in 1951 and the international political and economic implication of these activities. Chapter III explains the activities of NIOC in Iran. Exploration and drilling, production, exports, refineries, natural gas, petrochemicals and internal distributions are studied. Chapter IV discusses the role of the development planning of Iran. A brief presentation of the First Development Plan through the Fifth Development Plan is given. Sources and uses of funds by plan organization during these Five Plans is studied. The Iran and Iraq War is also studied briefly, but the uncertainty of its resolution prevents any close analysis of its impact on the Iranian oil industry. One conclusion, however, is certain; oil has been a vital resource in Iran's past and it will remain the lifetime of its economic development in the future.

  3. Industrial Training Handbook.

    ERIC Educational Resources Information Center

    Barber, John W., Ed.

    This industrial training handbook covers the following areas: preparatory considerations; training methods and techniques; training for specific functions; and established organizations. Part I examines the extension and re-designing of technical colleges since the 1920's and the present integration of the work of colleges with the needs of…

  4. Industrial Organic Electrosynthesis.

    ERIC Educational Resources Information Center

    Wagenknecht, John H.

    1983-01-01

    Four examples of industrial electrochemical synthesis of organic compounds are described. These include acrylonitrile dimerization, tetramethyl lead, electrochemical fluorination, and production of diacetone-2-keto-L-gulonic acid. Additional examples are also cited, including the production of several compounds by the BASF company of Germany. (JN)

  5. Recent developments: Industry briefs

    SciTech Connect

    1992-02-01

    This is the February 1992 `Industry Briefs` portion of the `Recent Developments` section. Issues mentioned are: (1) closure of San Onofre Unit 1, (2) start-up of Penly Unit 2, (3) signing of a safeguards agreement with North Korea, (4) Canadian nuclear activities in Romania, and (5) the merger of two Japanese fuel cycle companies.

  6. Building Industries Occupations: Syllabus.

    ERIC Educational Resources Information Center

    New York State Education Dept., Albany. Bureau of Secondary Curriculum Development.

    The Building Industries Occupations course is a two-year program of approximately 160 three-period teaching days per year. The required course content is designed to be effectively taught in 80 percent of the total course time, thus allowing 20 percent of the time for instruction adapted to such local conditions as employment prospects, student…

  7. Today's Business Simulation Industry

    ERIC Educational Resources Information Center

    Summers, Gary J.

    2004-01-01

    New technologies are transforming the business simulation industry. The technologies come from research in computational fields of science, and they endow simulations with new capabilities and qualities. These capabilities and qualities include computerized behavioral simulations, online feedback and coaching, advanced interfaces, learning on…

  8. Ethics for Industrial Technology

    ERIC Educational Resources Information Center

    Rosentrater, Kurt A.; Balamuralikrishna, Radha

    2005-01-01

    This paper takes aim at one specific, as well as basic, need in teamwork and interdisciplinary projects--ethics and its implications for professional practice. A preliminary study suggests that students majoring in industrial technology degree programs may not have adequate opportunity to formally study and engage in ethical aspects of technology…

  9. Working with Industry

    ERIC Educational Resources Information Center

    Ullman, Ellen

    2012-01-01

    As community colleges focus on becoming more efficient and preparing more students for success in a climate of reduced state and federal funding, many institutions are reaching out to neighbors in business and industry, forming partnerships and working together to achieve goals that require money and resources colleges are unlikely to raise on…

  10. Water Pollution Control Industry

    ERIC Educational Resources Information Center

    Environmental Science and Technology, 1974

    1974-01-01

    A special report on the state of the water pollution control industry reveals that due to forthcoming federal requirements, sales and the backlogs should increase; problems may ensue because of shortages of materials and inflation. Included are reports from various individual companies. (MLB)

  11. Industrial Education Curriculum.

    ERIC Educational Resources Information Center

    Alaska State Dept. of Education, Juneau. Div. of Adult and Vocational Education.

    This handbook contains a competency-based curriculum for teaching industrial education in Alaska. Competencies are listed for the following areas: employability, auto maintenance, building maintenance, commercial fishing, communications, construction, drafting, electronics, energy and power, forestry and logging, graphics, high technology,…

  12. Moving up in industry.

    PubMed

    Covell, Charlotte

    2016-01-23

    Charlotte Covell is commercial business manager at Virbac UK, a role that gives her responsibility for the company's sales to corporate practices, some buying groups and internet pharmacies. She began her career as a veterinary nurse, but moved into industry and now has a role in senior business management.

  13. Industrial Education. "Small Engines".

    ERIC Educational Resources Information Center

    Parma City School District, OH.

    Part of a series of curriculum guides dealing with industrial education in junior high schools, this guide provides the student with information and manipulative experiences on small gasoline engines. Included are sections on shop adjustment, safety, small engines, internal combustion, engine construction, four stroke engines, two stroke engines,…

  14. Industrial Training Practices.

    ERIC Educational Resources Information Center

    Beverstock, A.G.

    Based primarily on British conditions, this volume concentrates on methods of industrial training for production workers, craftsmen and technicians, office personnel, technicians and technologists, supervisors, marketing and sales personnel, and the junior, middle, and senior or executive levels of management. General principles and fundamental…

  15. Industrial Education Safety Guide.

    ERIC Educational Resources Information Center

    California State Dept. of Education, Sacramento.

    California is one of the few states in which school districts have a legal responsibility for accidents involving students while they are participating in assigned school activities. This guide was prepared to help school administrators and teachers evaluate their safety instruction programs and industrial education facilities in accordance with…

  16. Steel Industry Wastes.

    ERIC Educational Resources Information Center

    Schmidtke, N. W.; Averill, D. W.

    1978-01-01

    Presents a literature review of wastes from steel industry, covering publications of 1976-77. This review covers: (1) coke production; (2) iron and steel production; (3) rolling operations; and (4) surface treatment. A list of 133 references is also presented. (NM)

  17. Industrial Radiography Instructor's Guide.

    ERIC Educational Resources Information Center

    Richardson, Harry D.

    The curriculum guide was developed for teacher use in an 80-hour course for industrial radiographers. The units include: (1) The Structure of Matter and Radiation, (2) Nuclear Reactions and Radioisotopes, (3) The Nature and Consequences of Radiation Exposure, (4) Radiation Attenuation, (5) Absorption of Radiation, (6) Radiation Detection and…

  18. The changing solar industry

    SciTech Connect

    Wilson, A.

    1990-03-01

    The July 1989 announcement that Atlantic Richfield had agreed to sell its ARCO Solar division to Siemens of West Germany sent shock waves throughout the U.S. photovoltaics (PV) industry, the U.S. Department of Energy (DOE) and among investigators. The largest PV manufacturer in the world was being sold because it had failed to make enough money for its parent company, and a foreign company was purchasing it - presumably because no U.S. company or investor package had come up with a high enough offer. Given the millions of dollars in government financed research and development funds that ARCO had benefited from, some government officials talked of blocking the sale, an effort that could only have succeeded if it was demonstrated that the sale would compromise national security - which was not the case. With the acquisition scheduled to be completed on February 28, 1990 - the newly acquired company will be called Siemens Solar Industries - many in the industry were wondering what the impact on the industry would be. Would buy-America sentiment help Siemens Solar's competitors Would investors become nervous over the potential profitability of any PV companies and pull back Would it become more difficult to obtain R D funds from a now gun-shy Department of Energy These questions are discussed.

  19. Industrial Ceramics: Secondary Schools.

    ERIC Educational Resources Information Center

    New York City Board of Education, Brooklyn, NY. Bureau of Curriculum Development.

    The expanding use of ceramic products in today's world can be seen in the areas of communications, construction, aerospace, textiles, metallurgy, atomic energy, and electronics. The demands of science have brought ceramics from an art to an industry using mass production and automated processes which requires the services of great numbers as the…

  20. Industrial Education Resources.

    ERIC Educational Resources Information Center

    Alaska State Dept. of Education, Juneau. Div. of Adult and Vocational Education.

    This guide was developed as a supplement to the Alaska Department of Education's industrial education curriculum. The special topics included in it focus on competencies from the curriculum for which materials were not readily available to Alaskan teachers and provide information that may not be sufficiently covered by existing curricula. Each…

  1. Industrial power distribution

    SciTech Connect

    Sorrells, M.A.

    1990-01-01

    This paper is a broad overview of industrial power distribution. Primary focus will be on selection of the various low voltage components to achieve the end product. Emphasis will be on the use of national standards to ensure a safe and well designed installation.

  2. RETRAINING BY PRIVATE INDUSTRY.

    ERIC Educational Resources Information Center

    HOOS, IDA R.

    SEVERAL SAN FRANCISCO BAY AREA COMPANIES WERE EXAMINED FOR SPECIFIC PROGRAMS FOR DISPLACED EMPLOYEES. ARMOUR AND COMPANY SOUGHT TO GUIDE DISPLACED EMPLOYEES TO CLASSES OR COURSES OF ACTION OUTSIDE ITS OWN SPHERE OF OPERATION. LOCKHEED HAS PROVIDED UNUSUALLY WELL FOR UPGRADING AND RETRAINING, MAINLY BECAUSE OF INDUSTRY FLUCTUATIONS AND RAPID…

  3. Industrial Mechanical Maintenance.

    ERIC Educational Resources Information Center

    Hendrix, Laborn J.

    This manual was developed to assist teachers in Oklahoma in preparing students for industrial mechanical maintenance. The materials in this teacher's guide are organized in 14 units of instruction covering the following four areas: receiving and setting equipment; equipment hookup and operation; equipment layout, anchoring, and setup; and…

  4. Industrial Chemistry for Teachers

    ERIC Educational Resources Information Center

    Cooley, William E.

    1970-01-01

    Discusses the role of the applied research chemist in industry. Several examples of applied research are cited in moderate detail, all of them related to the development of anticaries dentifrices. A number of testing methods developed by basic and applied researchers are discussed. Bibliography. (LC)

  5. INTERMOUNTAIN INDUSTRIAL ASSESSMENT CENTER

    SciTech Connect

    MELINDA KRAHENBUHL

    2010-05-28

    The U. S. Department of Energy’s Intermountain Industrial Assessment Center (IIAC) at the University of Utah has been providing eligible small- and medium-sized manufacturers with no-cost plant assessments since 2001, offering cost-effective recommendations for improvements in the areas of energy efficiency, pollution prevention, and productivity improvement.

  6. Industrial Arts and Technology.

    ERIC Educational Resources Information Center

    Baird, David A.

    Increased emphasis on academic and mathematical skills in high school courses such as "technology education" appeal only to the above average and motivated students, leaving a large majority of less-able students with a distorted view of future jobs, which do not, in fact, require such an academic approach. At the same time, industrial arts…

  7. TRAINING IN INDUSTRY.

    ERIC Educational Resources Information Center

    GLASER, ROBERT

    THIS CHAPTER IN A LARGER WORK ON INDUSTRIAL PSYCHOLOGY DEALS LARGELY WITH THE NEED TO SPECIFY TRAINING OBJECTIVES THROUGH JOB ANALYSIS, USES OF TESTING IN TRAINEE SELECTION, TRAINING VARIABLES AND LEARNING PROCESSES, TRAINING TECHNOLOGY (MAINLY THE CHARACTERISTICS OF PROGRAMED INSTRUCTION), THE EVALUATION OF PROFICIENCY, THE VALUE OF…

  8. Industrial cogeneration optimization program

    SciTech Connect

    Not Available

    1980-01-01

    The purpose of this program was to identify up to 10 good near-term opportunities for cogeneration in 5 major energy-consuming industries which produce food, textiles, paper, chemicals, and refined petroleum; select, characterize, and optimize cogeneration systems for these identified opportunities to achieve maximum energy savings for minimum investment using currently available components of cogenerating systems; and to identify technical, institutional, and regulatory obstacles hindering the use of industrial cogeneration systems. The analysis methods used and results obtained are described. Plants with fuel demands from 100,000 Btu/h to 3 x 10/sup 6/ Btu/h were considered. It was concluded that the major impediments to industrial cogeneration are financial, e.g., high capital investment and high charges by electric utilities during short-term cogeneration facility outages. In the plants considered an average energy savings from cogeneration of 15 to 18% compared to separate generation of process steam and electric power was calculated. On a national basis for the 5 industries considered, this extrapolates to saving 1.3 to 1.6 quads per yr or between 630,000 to 750,000 bbl/d of oil. Properly applied, federal activity can do much to realize a substantial fraction of this potential by lowering the barriers to cogeneration and by stimulating wider implementation of this technology. (LCL)

  9. An Industry Redefined

    ERIC Educational Resources Information Center

    Breeding, Marshall

    2007-01-01

    Activities in 2006 pointed to strategic shifts in library automation. The dynamics of the business environment changed rapidly from a fragmented industry to a highly consolidated one. Though the integrated library system (ILS) continues to represent the largest portion of revenue, products that deal with electronic content and deliver better…

  10. Manufacturing (Industrial) Technician.

    ERIC Educational Resources Information Center

    Ohio State Univ., Columbus. Center on Education and Training for Employment.

    This document contains 35 units to consider for use in a tech prep competency profile for the occupation of manufacturing (industrial) technician. All the units listed will not necessarily apply to every situation or tech prep consortium, nor will all the competencies within each unit be appropriate. Several units appear within each specific…

  11. Language Industries Atlas.

    ERIC Educational Resources Information Center

    Hearn, P. M., Ed.; Button, D. F., Ed.

    This atlas describes the activities of public and private organizations that create the infrastructure within which languages are able to develop and interact in the European Community (EC). It contains over 1,000 descriptions of activities that play a role in shaping the language industries, from a user or provider perspective. The atlas is…

  12. Engineering Industry Training Board

    ERIC Educational Resources Information Center

    Industrial Training International, 1974

    1974-01-01

    The Engineering Industry Training Board has produced a method enabling the office supervisor or departmental manager to control the critical parts of his systems--the Commercial Systems Practice (CSP). The systems plot, the staff/task matrix, performance indicators, and benefits of the CSP technique are discussed. (Author/MW)

  13. Industrial Assessment Center

    SciTech Connect

    Umesh K. Saxena

    2009-06-04

    This project involved providing technical assistance to help small and medium size industries in Wisconsin to reduce operating costs by managing energy, waste and productivity. The project helped save 525 companies on average about $40,000 per year. Under the direction of Dr. Saxena, more than twenty undergraduate and ten graduate students were trained in energy, waste, and productivity management.

  14. Introduction to industrial crops

    Technology Transfer Automated Retrieval System (TEKTRAN)

    While any seed oil can fill certain non-food applications, there are hundreds of seed oils containing a different complement of fatty acids that impart physical and chemical properties making the oil and associated fatty acids especially useful for industrial and other non-food uses. These differenc...

  15. Printed circuit board industry.

    PubMed

    LaDou, Joseph

    2006-05-01

    The printed circuit board is the platform upon which microelectronic components such as semiconductor chips and capacitors are mounted. It provides the electrical interconnections between components and is found in virtually all electronics products. Once considered low technology, the printed circuit board is evolving into a high-technology product. Printed circuit board manufacturing is highly complicated, requiring large equipment investments and over 50 process steps. Many of the high-speed, miniaturized printed circuit boards are now manufactured in cleanrooms with the same health and safety problems posed by other microelectronics manufacturing. Asia produces three-fourths of the world's printed circuit boards. In Asian countries, glycol ethers are the major solvents used in the printed circuit board industry. Large quantities of hazardous chemicals such as formaldehyde, dimethylformamide, and lead are used by the printed circuit board industry. For decades, chemically intensive and often sloppy manufacturing processes exposed tens of thousands of workers to a large number of chemicals that are now known to be reproductive toxicants and carcinogens. The printed circuit board industry has exposed workers to high doses of toxic metals, solvents, acids, and photolithographic chemicals. Only recently has there been any serious effort to diminish the quantity of lead distributed worldwide by the printed circuit board industry. Billions of electronics products have been discarded in every region of the world. This paper summarizes recent regulatory and enforcement efforts. PMID:16580876

  16. Comparing the Thermodynamic Behaviour of Al(1)+ZrO2(s) to Al(1)+Al2O3(s)

    NASA Technical Reports Server (NTRS)

    Copland, Evan

    2004-01-01

    In an effort to better determine the thermodynamic properties of Al(g) and Al2O(g). the vapor in equilibrium with Al(l)+ZrO2(s) was compared to the vapor in equilibrium with Al(l)+Al2O3(s) over temperature range 1197-to-1509K. The comparison was made directly by Knudsen effusion-cell mass spectrometry with an instrument configured for a multiple effusion-cell vapor source (multi-cell KEMS). Second law enthalpies of vaporization of Al(g) and Al2O(g) together with activity measurements show that Al(l)+ZrO2(s) is thermodynamically equivalent to Al(l)+Al2O3(s), indicating Al(l) remained pure and Al2O3(s) was present in the ZrO2-cell. Subsequent observation of the Al(l)/ZrO2 and vapor/ZrO2 interfaces revealed a thin Al2O3-layer had formed, separating the ZrO2-cell from Al(l) and Al(g)+Al2O(g), effectively transforming it into an Al2O3 effusion-cell. This behavior agrees with recent observations made for Beta-NiAl(Pt) alloys measured in ZrO2 effusion-cell.

  17. Ab initio modeling of zincblende AlN layer in Al-AlN-TiN multilayers

    NASA Astrophysics Data System (ADS)

    Yadav, S. K.; Wang, J.; Liu, X.-Y.

    2016-06-01

    An unusual growth mechanism of metastable zincblende AlN thin film by diffusion of nitrogen atoms into Al lattice is established. Using first-principles density functional theory, we studied the possibility of thermodynamic stability of AlN as a zincblende phase due to epitaxial strains and interface effect, which fails to explain the formation of zincblende AlN. We then compared the formation energetics of rocksalt and zincblende AlN in fcc Al through direct diffusion of nitrogen atoms to Al octahedral and tetrahedral interstitials. The formation of a zincblende AlN thin film is determined to be a kinetically driven process, not a thermodynamically driven process.

  18. Influence of the Al distribution on the structure, elastic properties, and phase stability of supersaturated Ti{sub 1-x}Al{sub x}N

    SciTech Connect

    Mayrhofer, P. H.; Music, D.; Schneider, J. M.

    2006-11-01

    Ti{sub 1-x}Al{sub x}N films and/or their alloys are employed in many industrial applications due to their excellent mechanical and thermal properties. Synthesized by plasma-assisted vapor deposition, Ti{sub 1-x}Al{sub x}N is reported to crystallize in the cubic NaCl (c) structure for AlN mole fractions below 0.4-0.91, whereas at larger Al contents the hexagonal ZnS-wurtzite (w) structure is observed. Here we use ab initio calculations to analyze the effect of composition and Al distribution on the metal sublattice on phase stability, structure, and elastic properties of c-Ti{sub 1-x}Al{sub x}N and w-Ti{sub 1-x}Al{sub x}N. We show that the phase stability of supersaturated c-Ti{sub 1-x}Al{sub x}N not only depends on the chemical composition but also on the Al distribution of the metal sublattice. An increase of the metastable solubility limit of AlN in c-Ti{sub 1-x}Al{sub x}N from 0.64 to 0.74 is obtained by decreasing the number of Ti-Al bonds. This can be understood by considering the Al distribution induced changes of the electronic structure, bond energy, and configurational entropy. This may in part explain the large variation of the metastable solubility limit reported in the literature.

  19. [Metalworking industry management evolution].

    PubMed

    Mattucci, Massimo

    2011-01-01

    Analysis of the evolution drivers of the management systems in the metalworking industry, mainly characterized as "automotive", starting with the "mass production" model, followed for the development of Italian industry in the '50. Through the socio-economic changes of the '90/10, the metalworking plants were deeply restructured with the introduction of computers in the production systems, and then with the first global benchmarks such as the "lean production", towards the needed operational flexibility to respond to the market dynamics. Plants change radically, company networks become real, ICT services are fundamental elements for the integration. These trends help visualizing a new "Factory of the Future" for the years 2020/30, where the competition will be based on the socio-economical, technological and environmental factors included in the "Competitive Sustainable Manufacturing" paradigm. PMID:22073665

  20. LBL industry review

    SciTech Connect

    Benoit, D. )

    1993-01-01

    This is a general summary of a meeting on March 16, 1993 of the LBL Industry Review Panel on Exploration and Reservoir Technology. It met in three subpanels to consider (1) exploration for new discoveries (2) mapping reservoir properties and monitoring production/injection (3) well testing, reservoir simulation, and predicting future reservoir performance. This very brief meeting only allowed very broad coverage of concerns. There is a growing commercial development of liquid based geothermal reservoirs, and they are encountering problems for which they are asking for research dollars. This will probably cause a shift in research spending as there is a limited number of dollars available, and the vapor based Geysers has received most funding to this point. All three panels felt the need to see more case studies, whether they reached positive or negative conclusions. This may be forthcoming as consolidation in the industry is reducing the need to shield information from competitors.

  1. Diaper industry workshop report

    SciTech Connect

    Not Available

    1991-05-01

    The report is the product of a one-day workshop on the diaper industry that was sponsored by the U.S. EPA. Four topics covered during the workshop were public health and safety, recycling, composting, and product life cycle analysis. The primary objective of the workshop was to identify areas within the diaper industry that need further research in order to lessen the adverse impacts that diapers have on the environment. Summaries of each of the four topics as well as summaries of discussion comments and research needs identified during the workshop are included in the report. A large number of research ideas were generated during the workshop. These ideas included determining the health risks associated with handling diapers, developing methods for improving the recyclability of plastics used in diapers, determining where diaper-related life cycle analysis should begin and end, and determining the economic viability of composting.

  2. Robotics and industrial inspection

    SciTech Connect

    Casasent, D.P.

    1983-01-01

    Image processing algorithms are discussed, taking into account hidden information in early visual processing, three-dimensional shape recognition by moirecorrelation, spatial-frequency representations of images with scale invariant properties, image-based focusing, the computational structure for the Walsh-Hadamard transform, a hybrid optical/digital moment-based robotic pattern recognition system, affordable implementations of image processing algorithms, and an analysis of low-level computer vision algorithms for implementation on a very large scale integrated processor array. Other topics considered are related to government programs and needs in robotics, DoD research and applications in robotics, time-varying image processing and control, industrial robotics, industrial applications of computer vision, and object perception and mensuration for robotics. Attention is given to laser scanning techniques for automatic inspection of heat-sealed film packages, computer software for robotic vision, and computerized tomography on a logarithmic polar grid.

  3. Industrial ecotoxicology "acid rain".

    PubMed

    Astolfi, E; Gotelli, C; Higa, J

    1986-01-01

    The acid rain phenomenon was studied in the province of Cordoba, Argentina. This study, based on a previously outlined framework, determined the anthropogenic origin of the low pH due to the presence of industrial hydrochloric acid wastage. This industrial ecotoxicological phenomenon seriously affected the forest wealth, causing a great defoliation of trees and shrubs, with a lower effect on crops. A survey on its effects on human beings has not been carried out, but considering the corrosion caused to different metals and its denouncing biocide effect on plants and animals, we should expect to find some kind of harm to the health of the workers involved or others engaged in farming, and even to those who are far away from the polluting agent. PMID:3758667

  4. US cement industry

    SciTech Connect

    Nisbet, M.A.

    1997-12-31

    This paper describes the cement and concrete industry, and provides data on energy use and carbon dioxide emissions. The potential impact of an energy tax on the industry is briefly assessed. Opportunities identified for reducing carbon dioxide emissions include improved energy efficiency, alternative fuels, and alternative materials. The key factor in determining CO{sub 2} emissions is the level of domestic production. The projected improvement in energy efficiency and the relatively slow growth in domestic shipments indicate that CO{sub 2} emissions in 2000 should be about 5% above the 1990 target. However, due to the cyclical nature of cement demand, emissions will probably be above target levels during peak demand and below target levels during demand troughs. 7 figs., 2 tabs.

  5. Coal industry annual 1997

    SciTech Connect

    1998-12-01

    Coal Industry Annual 1997 provides comprehensive information about US coal production, number of mines, prices, productivity, employment, productive capacity, and recoverable reserves. US Coal production for 1997 and previous years is based on the annual survey EIA-7A, Coal Production Report. This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report includes a national total coal consumption for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. 14 figs., 145 tabs.

  6. Industrial ecotoxicology "acid rain".

    PubMed

    Astolfi, E; Gotelli, C; Higa, J

    1986-01-01

    The acid rain phenomenon was studied in the province of Cordoba, Argentina. This study, based on a previously outlined framework, determined the anthropogenic origin of the low pH due to the presence of industrial hydrochloric acid wastage. This industrial ecotoxicological phenomenon seriously affected the forest wealth, causing a great defoliation of trees and shrubs, with a lower effect on crops. A survey on its effects on human beings has not been carried out, but considering the corrosion caused to different metals and its denouncing biocide effect on plants and animals, we should expect to find some kind of harm to the health of the workers involved or others engaged in farming, and even to those who are far away from the polluting agent.

  7. Industrialization of Biology.

    PubMed

    Friedman, Douglas C; Ellington, Andrew D

    2015-10-16

    The advancement of synthetic biology over the past decade has contributed substantially to the growing bioeconomy. A recent report by the National Academies highlighted several areas of advancement that will be needed for further expansion of industrial biotechnology, including new focuses on design, feedstocks, processing, organism development, and tools for testing and measurement; more particularly, a focus on expanded chassis and end-to-end design in an effort to move beyond the use of E. coli and S. cerivisiea to organisms better suited to fermentation and production; second, continued efforts in systems biology and high-throughput screening with a focus on more rapid techniques that will provide the needed information for moving to larger scale; and finally, work to accelerate the building of a holacratic community with collaboration and engagement between the relevant government agencies, industry, academia, and the public.

  8. Coal industry annual 1993

    SciTech Connect

    Not Available

    1994-12-06

    Coal Industry Annual 1993 replaces the publication Coal Production (DOE/FIA-0125). This report presents additional tables and expanded versions of tables previously presented in Coal Production, including production, number of mines, Productivity, employment, productive capacity, and recoverable reserves. This report also presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for a wide audience including the Congress, Federal and State agencies, the coal industry, and the general public. In addition, Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility Power Producers who are not in the manufacturing, agriculture, mining, construction, or commercial sectors. This consumption is estimated to be 5 million short tons in 1993.

  9. Program on purification of industrial waste water. Country paper: Ethiopia

    SciTech Connect

    Mebratu, D.

    1990-09-10

    The paper as a preliminary country paper for the UNIDO's programe on Industrial waste water purification, which embraces eight countries from Africa, is prepared in such a way that it could serve as source materi al for the programs implementation in the country. The program's main objective being developing the most appropriate and effective means to deal with long term problems associated with generation and treatment of industrial waste water influence, every effort is made to present what ever relevant informations pertaining to the program's objective and goal. To this end, the first chapter delivers general background information about the countries natural resource and the prevailing industrial feature, while the second chapter deliberates on the results of the investigation and evaluation of the selected subsectors and factories from the industrial sector. Finally, an overview of other side factors which could possibly have effects on the project's activity is presented in the third chapter.

  10. Laser remelting of Ti6AL4V using high power diode laser

    NASA Astrophysics Data System (ADS)

    Amaya-Vázquez, M. R.; Sánchez-Amaya, J. M.; Boukha, Z.; El Amrani, K.; Botana, F. J.

    2012-04-01

    Titanium alloys present excellent mechanical and corrosion properties, being widely employed in different industries such as medical, aerospace, automotive, petrochemical, nuclear and power generation, etc. Ti6Al4V is the α-β alloy most employed in industry. The modification of its properties can be achieved with convectional heat treatments and/or with laser processing. Laser remelting (LR) is a technology applied to Ti6Al4V by other authors with excimer and Nd-Yag laser with pure argon shielding gas to prevent risk of oxidation. In the present contribution, laser remelting has been applied for the first time to Ti6Al4V with a high power diode laser (with pure argon as shielding gas). Results showed that remelted samples (with medium energy densities) have higher microhardness and better corrosion resistance than Ti6Al4V base metal.

  11. Industrial Computer Codes

    NASA Technical Reports Server (NTRS)

    Shapiro, Wilbur

    1996-01-01

    This is an overview of new and updated industrial codes for seal design and testing. GCYLT (gas cylindrical seals -- turbulent), SPIRALI (spiral-groove seals -- incompressible), KTK (knife to knife) Labyrinth Seal Code, and DYSEAL (dynamic seal analysis) are covered. CGYLT uses G-factors for Poiseuille and Couette turbulence coefficients. SPIRALI is updated to include turbulence and inertia, but maintains the narrow groove theory. KTK labyrinth seal code handles straight or stepped seals. And DYSEAL provides dynamics for the seal geometry.

  12. Energy industries abroad

    NASA Astrophysics Data System (ADS)

    1981-09-01

    The relationships between foreign governments and energy industries in many of the world's most important energy producing and consuming nations are examined. The history of hydrocarbon exploration and production is traced and the concessionary and other contractual arrangements entered into by foreign governments and international oil companies are reviewed. Petroleum legislation that was enacted, how government institutions gradually assumed more responsibility for energy matters, and how the former concessionaires adapted to accommodate this increased government participation in the energy sector is described.

  13. Industrial Analytics Corporation

    SciTech Connect

    Industrial Analytics Corporation

    2004-01-30

    The lost foam casting process is sensitive to the properties of the EPS patterns used for the casting operation. In this project Industrial Analytics Corporation (IAC) has developed a new low voltage x-ray instrument for x-ray radiography of very low mass EPS patterns. IAC has also developed a transmitted visible light method for characterizing the properties of EPS patterns. The systems developed are also applicable to other low density materials including graphite foams.

  14. Glass Industry Bandwidth Analysis

    SciTech Connect

    Rue, David M.

    2006-07-01

    This is a study on energy use and potential savings, or "bandwidth" study, for several glassmaking processes. Intended to provide a realistic estimate of the potential amount of energy that can be saved in an industrial process, the "bandwidth" refers to the difference between the amount of energy that would be consumed in a process using commercially available technology versus the minimum amount of energy needed to achieve those same results.

  15. Industrial Glass Bandwidth Analysis

    SciTech Connect

    Rue, David M.; Servaites, James; Wolf, Warren

    2007-08-01

    This is a study on energy use and potential savings, or "bandwidth" study, for several glassmaking processes. Intended to provide a realistic estimate of the potential amount of energy that can be saved in an industrial process, the "bandwidth" refers to the difference between the amount of energy that would be consumed in a process using commercially available technology versus the minimum amount of energy needed to achieve those same results.

  16. Industrial labor relations manual

    NASA Technical Reports Server (NTRS)

    1992-01-01

    The NASA Industrial Labor Relations Manual provides internal guidelines and procedures to assist NASA Field Installations in dealing with contractor labor management disputes, Service Contract Act variance hearings, and to provide access of Labor Union Representatives to NASA for the purpose of maintaining schedules and goals in connection with vital NASA programs. This manual will be revised by page changes as revisions become necessary. Initial distribution of this manual has been made to NASA Headquarters and Field Installations.

  17. Recent developments: Industry briefs

    SciTech Connect

    1990-09-01

    Recent nuclear industry briefs are presented. These briefs include: Bechtel, Westinghouse and consumers form joint venture to operate Palisades; British Goverment to sell PowerGen in public offering; NPT conference opens in Geneva; Soviets buy US computers for nuclear safety; Cameco completes sale of interest in Rabbit Lake; Ebasco and CEGA each win defense reactor contract; East German utility takeover settled; Rio Algom shuts down Quirke and Panel early; and General Atomics buys Beverly mine.

  18. Industrial membrane processes

    SciTech Connect

    White, R.E.; Pintauro, P.N.

    1986-01-01

    This book presents the papers given a symposium on the use of membranes in industrial plants. Topics considered include the effect of biofilm formation on salinity power plant output on a laboratory scale, an engineering analysis of membrane-aided distillation, the development and evaluation of sulfonated polysulfone membranes for the zinc/ferricyanide battery, and the degradation of ionic membranes in the zinc/ferricyanide battery.

  19. Poultry Industry Energy Research

    NASA Technical Reports Server (NTRS)

    1979-01-01

    The poultry industry, a multi-billion dollar business in the United States, uses great amounts of energy in such operations as broiler growing, feed manufacturing, poultry processing and packing. Higher costs and limited supply of fuels common to the industry are predicted, so poultry producers are seeking ways to reduce energy expenditure. NASA is providing assistance to Delmarva Poultry Industry, Inc., an association of some 4,000 growers and suppliers in one of the nation's largest poultry production areas. Delmarva is the East Coast peninsula that includes Delaware and parts of Maryland and Virginia. The upper right photo shows a weather station in the Delmarva area (wind indicator on the pole, other instruments in the elevated box). The station is located at the University of Maryland's Broiler Sub-station, Salisbury; Maryland, where the university conducts research on poultry production and processing. The sub-station is investigating ways of conserving energy in broiler production and also exploring the potential of solar collectors as an alternative energy source. For these studies, it is essential that researchers have continuous data on temperature, pressure, wind speed and direction, solar intensity and cloud cover. Equipment to acquire such data was loaned and installed by NASA's Wallops Flight Center, Wallops Island, Virginia.

  20. Distance collaborations with industry

    SciTech Connect

    Peskin, A.; Swyler, K.

    1998-06-01

    The college industry relationship has been identified as a key policy issue in Engineering Education. Collaborations between academic institutions and the industrial sector have a long history and a bright future. For Engineering and Engineering Technology programs in particular, industry has played a crucial role in many areas including advisement, financial support, and practical training of both faculty and students. Among the most important and intimate interactions are collaborative projects and formal cooperative education arrangements. Most recently, such collaborations have taken on a new dimension, as advances in technology have made possible meaningful technical collaboration at a distance. There are several obvious technology areas that have contributed significantly to this trend. Foremost is the ubiquitous presence of the Internet. Perhaps almost as important are advances in computer based imaging. Because visual images offer a compelling user experience, it affords greater knowledge transfer efficiency than other modes of delivery. Furthermore, the quality of the image appears to have a strongly correlated effect on insight. A good visualization facility offers both a means for communication and a shared information space for the subjects, which are among the essential features of both peer collaboration and distance learning.

  1. View from industry.

    PubMed

    Guezuraga, Robert M; Steinbring, Denise Y

    2004-12-01

    The transformation of the cardiothoracic specialty requires a complete mind-set and skill-set change such that the specialty repositions itself in this era of complex cardiac disease, increased competition, technology innovation, financial constraints, rationed access to technology and increased scrutiny on clinical outcomes. The future offers a variety of surgical treatment options for patients suffering from disease states that have traditionally not been treated by cardiothoracic surgeons such as ablation for atrial fibrillation and cell therapy for heart failure. In addition, patient expectations for prolonged and quality-improved years are higher as they educate themselves on options that are less invasive. Failure to build a new repertoire of skills will mean diminished access to patients because referrals will be made to those cardiothoracic surgeons who are seen as innovators. Time is of the essence, as market dynamics are taking their toll. Cardiothoracic surgery today is still one of the most profitable specialties within the hospital and therefore, hospitals should be willing to support and differentiate their heart programs through new technology adoption. But cardiothoracic surgeons need to be open to explore new methods for treating cardiac disease and to work with industry in proving the efficacy and patient benefits of new procedures. At a higher level, pan-European approaches to new technology adoption need to focus on increased governmental spending on healthcare and on reimbursement strategies that make this possible. The medical device industry continues to invest heavily in new techniques and technologies and should be viewed as a strategic partner by individual surgeons as well as by the surgical societies. As industry continues to focus on areas such as research, product development, market development, professional and resident education, reimbursement, and patient access issues, it is imperative for surgeons to work collaboratively with

  2. View from industry.

    PubMed

    Guezuraga, Robert M; Steinbring, Denise Y

    2004-12-01

    The transformation of the cardiothoracic specialty requires a complete mind-set and skill-set change such that the specialty repositions itself in this era of complex cardiac disease, increased competition, technology innovation, financial constraints, rationed access to technology and increased scrutiny on clinical outcomes. The future offers a variety of surgical treatment options for patients suffering from disease states that have traditionally not been treated by cardiothoracic surgeons such as ablation for atrial fibrillation and cell therapy for heart failure. In addition, patient expectations for prolonged and quality-improved years are higher as they educate themselves on options that are less invasive. Failure to build a new repertoire of skills will mean diminished access to patients because referrals will be made to those cardiothoracic surgeons who are seen as innovators. Time is of the essence, as market dynamics are taking their toll. Cardiothoracic surgery today is still one of the most profitable specialties within the hospital and therefore, hospitals should be willing to support and differentiate their heart programs through new technology adoption. But cardiothoracic surgeons need to be open to explore new methods for treating cardiac disease and to work with industry in proving the efficacy and patient benefits of new procedures. At a higher level, pan-European approaches to new technology adoption need to focus on increased governmental spending on healthcare and on reimbursement strategies that make this possible. The medical device industry continues to invest heavily in new techniques and technologies and should be viewed as a strategic partner by individual surgeons as well as by the surgical societies. As industry continues to focus on areas such as research, product development, market development, professional and resident education, reimbursement, and patient access issues, it is imperative for surgeons to work collaboratively with

  3. EDITORIAL: Industrial Process Tomography

    NASA Astrophysics Data System (ADS)

    Anton Johansen, Geir; Wang, Mi

    2008-09-01

    There has been tremendous development within measurement science and technology over the past couple of decades. New sensor technologies and compact versatile signal recovery electronics are continuously expanding the limits of what can be measured and the accuracy with which this can be done. Miniaturization of sensors and the use of nanotechnology push these limits further. Also, thanks to powerful and cost-effective computer systems, sophisticated measurement and reconstruction algorithms previously only accessible in advanced laboratories are now available for in situ online measurement systems. The process industries increasingly require more process-related information, motivated by key issues such as improved process control, process utilization and process yields, ultimately driven by cost-effectiveness, quality assurance, environmental and safety demands. Industrial process tomography methods have taken advantage of the general progress in measurement science, and aim at providing more information, both quantitatively and qualitatively, on multiphase systems and their dynamics. The typical approach for such systems has been to carry out one local or bulk measurement and assume that this is representative of the whole system. In some cases, this is sufficient. However, there are many complex systems where the component distribution varies continuously and often unpredictably in space and time. The foundation of industrial tomography is to conduct several measurements around the periphery of a multiphase process, and use these measurements to unravel the cross-sectional distribution of the process components in time and space. This information is used in the design and optimization of industrial processes and process equipment, and also to improve the accuracy of multiphase system measurements in general. In this issue we are proud to present a selection of the 145 papers presented at the 5th World Congress on Industrial Process Tomography in Bergen

  4. Industrial Technology Programs: The Influence of Industry on Program Revision.

    ERIC Educational Resources Information Center

    Kozak, Michael R.; Richards, John V.

    1981-01-01

    Presents data collected concerning concepts and skills which should be emphasized in the general academic curriculum and in the industrial technology curriculum, recommended minor fields of study for industrial technology majors, characteristics of successful employees, and present and future professional industrial employment needs in the…

  5. The Rationale for Industrial Technology/Industrial Arts in Texas.

    ERIC Educational Resources Information Center

    Texas Education Agency, Austin.

    The goal of industrial technology for industrial arts education in Texas is the education of society to enable its members to function efficiently in the world of advancing technology. Policymakers in Texas have chosen to organize the industrial technology curriculum around three technology clusters: visual communication, production, and energy…

  6. The Computer Industry. High Technology Industries: Profiles and Outlooks.

    ERIC Educational Resources Information Center

    International Trade Administration (DOC), Washington, DC.

    A series of meetings was held to assess future problems in United States high technology, particularly in the fields of robotics, computers, semiconductors, and telecommunications. This report, which focuses on the computer industry, includes a profile of this industry and the papers presented by industry speakers during the meetings. The profile…

  7. Pyrogenic remobilization of historic industrial lead depositions.

    PubMed

    Odigie, Kingsley O; Flegal, A Russell

    2011-08-01

    Relatively high levels (4.3 to 51 μg/g) of labile lead (Pb) in ash from the 2009 Jesusita Fire in Santa Barbara County, California attest to the pyrogenic remobilization of historic industrial lead depositions in this relatively pristine area in Southern California, USA. The primarily industrial origin of that lead was evidenced by its poor correlations (simple linear regressions) with lithogenic aluminum (r = 0.18, p = 0.354, n = 30) and iron (r = 0.21, p = 0.270, n = 30) concentrations and by its associated enrichment factors (EFs): EF using aluminum as conservative element (f-Al) vs lead concentration [Pb] (r = 0.79, p < 0.001, n = 30), and EF using iron as conservative element (f-Fe) vs [Pb] (r = 0.83, p < 0.001, n = 30). The industrial origins of much of that lead were corroborated by its isotopic compositions ((206)Pb/(207)Pb and (208)Pb/(207)Pb), which fell between those of natural lead in the Santa Barbara Basin and previous leaded gasoline emissions in Southern California. This apparent pyrogenic remobilization of legacy lead pollution indicates that it-and other persistent pollutants-will increase with the projected increase in the frequency and intensity of forest fires in the Southwest U.S. and elsewhere as a consequence of climate change.

  8. The use of β titanium alloys in the aerospace industry

    NASA Astrophysics Data System (ADS)

    Boyer, R. R.; Briggs, R. D.

    2005-12-01

    Beta titanium alloys have been available since the 1950s (Ti-13V-11Cr-3Mo or B120VCA), but significant applications of these alloys, beyond the SR-71 Blackbird, have been slow in coming. The next significant usage of a β alloy did not occur until the mid-1980s on the B-1B bomber. This aircraft used Ti-15V-3Cr-3Al-3Sn sheet due to its capability for strip rolling, improved formability, and higher strength than Ti-6Al-4V. The next major usage was on a commercial aircraft, the Boeing 777, which made extensive use of Ti-10V-2Fe-3Al high-strength forgings. Ti-15V-3Cr-3Al-3Sn environmental control system ducting, castings, and springs were also used, along with Ti-3Al-8V-6Cr-4Mo-4Zr (β-C) springs. Beta-21S was also introduced for high-temperature usage. More recent work at Boeing has focused on the development of Ti-5Al-5Mo-5V-3Cr, a high-strength alloy that can be used at higher strength than Ti-10V-2Fe-3Al and is much more robust; it has a much wider, or friendlier, processing window. This, along with additional studies at Boeing, and from within the aerospace industry in general will be discussed in detail, summarizing applications and the rationale for the selection of this alloy system for aerospace applications.

  9. Recent Developments in Friction Stir Welding of Al-alloys

    NASA Astrophysics Data System (ADS)

    Çam, Gürel; Mistikoglu, Selcuk

    2014-06-01

    The diversity and never-ending desire for a better life standard result in a continuous development of the existing manufacturing technologies. In line with these developments in the existing production technologies the demand for more complex products increases, which also stimulates new approaches in production routes of such products, e.g., novel welding procedures. For instance, the friction stir welding (FSW) technology, developed for joining difficult-to-weld Al-alloys, has been implemented by industry in manufacturing of several products. There are also numerous attempts to apply this method to other materials beyond Al-alloys. However, the process has not yet been implemented by industry for joining these materials with the exception of some limited applications. The microstructures and mechanical properties of friction stir welded Al-alloys existing in the open literature will be discussed in detail in this review. The correlations between weld parameters used during FSW and the microstructures evolved in the weld region and thus mechanical properties of the joints produced will be highlighted. However, the modeling studies, material flow, texture formation and developments in tool design are out of the scope of this work as well as the other variants of this technology, such as friction stir spot welding (FSSW).

  10. Industrial Engineering Education: A Prospective.

    ERIC Educational Resources Information Center

    Elsayed, E. A.

    1999-01-01

    Presents an overview of the origin of the industrial engineering discipline and how the subject was taught in the early stages of its development. Describes current changes in the curricula to meet new requirements in industry. (Author/CCM)

  11. Dermatitis in rubber manufacturing industries

    SciTech Connect

    White, I.R.

    1988-01-01

    This review describes the history of rubber technology and the manufacturing techniques used in rubber manufacturing industries. The important aspects of the acquisition of allergic and irritant contact dermatitis within the industry are presented for the reader.

  12. Report of Industry Panel Group

    NASA Technical Reports Server (NTRS)

    Gallimore, Simon; Gier, Jochen; Heitland, Greg; Povinelli, Louis; Sharma, Om; VandeWall, Allen

    2006-01-01

    A final report is presented from the industry panel group. The contents include: 1) General comments; 2) Positive progress since Minnowbrook IV; 3) Industry panel outcome; 4) Prioritized turbine projects; 5) Prioritized compressor projects; and 6) Miscellaneous.

  13. Forest Products Industry Technology Roadmap

    SciTech Connect

    none,

    2010-04-01

    This document describes the forest products industry's research and development priorities. The original technology roadmap published by the industry in 1999 and was most recently updated in April 2010.

  14. Instructional Materials: The Changing Industry

    ERIC Educational Resources Information Center

    Brodinsky, Ben

    1975-01-01

    The beleaguered educational publishing industry is making a valiant stand against a storm of challenges. From eradicating bias in textbooks to verifying textbook effectiveness, many problems must be faced. The industry responds by cooperating with educators. (Editor)

  15. Andalusian astronomy: al-Zij al-Muqtabis of Ibn al-Kammâd.

    NASA Astrophysics Data System (ADS)

    Chabás, J.; Goldstein, B. R.

    1994-12-01

    In the twelfth century the Arabic astronomer Ibn al-Kammâd, living in Islamic Spain, composed three sets of astronomical tables, called "zijes". The zijes were largely based on the work of predecessors, going back to Ptolemy on the one hand, and Hindu astronomers on the other. None of his zijes survived in the original Arabic, but a Latin manuscript contains a translation of an apparently complete zij, the "al-Zij al-Muqtabis". This paper examines the body of astronomical knowledge contained in this zij. Specifically, it is shown that one can gain valuable information on the solar theory of the Islamic astronomers from this translation. Furthermore, the theory of lunar and solar eclipses in the work is analyzed, and tables of mean planetary and solar motions are discussed. In addition, tables for the motion of the vernal equinox, star tables, and several topics of Islamic spherical astronomy are examined.

  16. Microstructure Evolution and Mechanical Properties of Al/Al-Mg/Al composite sheet metals

    NASA Astrophysics Data System (ADS)

    Cho, Jaehyung; Kim, Su-Hyeon; Kim, Hyoung-Wook; Lim, Cha-Yong; Kim, Eun-Young; Choi, Shi-Hoon

    2011-08-01

    Two different types of aluminum alloys of AA1050 and AA5182 were used to manufacture Al/Al-Mg/Al composite sheet metals by roll bonding technology at room temperature. The composite sheet metals were annealed at 400 °C and carried out uniaxial tension tests to investigate mechanical properties. Macroscopic mechanical properties are strongly dependent on the volume (or thickness) fraction of two component layers. Microstructure and texture evolution were also investigated during roll bonding process. The AA1050 sheets located in the outer layer mainly consist of shear texture components and the AA5182 sheet located in the center layer consists of plane strain texture components. With differential speeds of the top and bottom rolls, roll bonding was also carried out. Elongation along the RD and TD was improved at a speed difference of approximately 10%-20%.

  17. Dynamic Modeling of ALS Systems

    NASA Technical Reports Server (NTRS)

    Jones, Harry

    2002-01-01

    The purpose of dynamic modeling and simulation of Advanced Life Support (ALS) systems is to help design them. Static steady state systems analysis provides basic information and is necessary to guide dynamic modeling, but static analysis is not sufficient to design and compare systems. ALS systems must respond to external input variations and internal off-nominal behavior. Buffer sizing, resupply scheduling, failure response, and control system design are aspects of dynamic system design. We develop two dynamic mass flow models and use them in simulations to evaluate systems issues, optimize designs, and make system design trades. One model is of nitrogen leakage in the space station, the other is of a waste processor failure in a regenerative life support system. Most systems analyses are concerned with optimizing the cost/benefit of a system at its nominal steady-state operating point. ALS analysis must go beyond the static steady state to include dynamic system design. All life support systems exhibit behavior that varies over time. ALS systems must respond to equipment operating cycles, repair schedules, and occasional off-nominal behavior or malfunctions. Biological components, such as bioreactors, composters, and food plant growth chambers, usually have operating cycles or other complex time behavior. Buffer sizes, material stocks, and resupply rates determine dynamic system behavior and directly affect system mass and cost. Dynamic simulation is needed to avoid the extremes of costly over-design of buffers and material reserves or system failure due to insufficient buffers and lack of stored material.

  18. Artificial intelligence in electric power systems--A survey of the Japanese industry

    SciTech Connect

    Rahman, S. )

    1993-08-01

    The major work on the theory and application of artificial intelligence (Al), which includes expert systems, is going on in the US, Europe and Japan. The Japanese electric utility industry, manufacturers, universities and the government have taken a focused goal-oriented approach in this regard. The author has studied the Japanese involvement in this field and visited eight Japanese R and D laboratories, where the Al and expert system related activities (in the power industry) is discussed. This paper provides a comprehensive look at the combined Japanese effort. The current topics of interest are: (1) Al and its application in power engineering; (2) problems in Al applications development and their solutions; (3) practical system examples; and (4) Al applications to power systems of the future. Out of the 97 papers cited in this paper, 10 were produced by electric utilities, 10 by manufacturers, 17 by universities and 60 were joint efforts. This shows the level and importance of joint collaborative research among the Japanese researchers. Even though they are working on many theoretical aspects of the Al technology including automated knowledge acquisition and verification, they still use significant amount of theoretical work done in the US for successful prototyping of Al based tools. It is, however, safe to say that the use of Al tools in the Japanese electric power industry is far more widespread than what is seen in the US or in Europe.

  19. Industry outreach a status report

    SciTech Connect

    Surek, D.; Sen, R.

    1995-09-01

    The Outreach Project was initiated in October 1994 with the objective of developing a multi-year plan for the U.S. Department of Energy (DOE) for targeted outreach activities for stakeholders in industry and the general public. This status report summarizes the work on industry outreach that has been completed since the inception of the project in October 1994. A three-pronged approach was taken to ascertain issues related to industry outreach. First, there was a review of on-going and past industry outreach activities at DOE and NHA. Next, a series of meetings with industry decision makers was arranged to get a better understanding of industry interests and concerns, and to discuss how DOE and industry could work collaboratively to develop hydrogen energy systems. Third, a workshop is scheduled where representatives from industry, DOE and other federal agencies can identify issues that would enhance partnering between the federal government and industry in the development of hydrogen energy systems. At this tiny, the review of on-going and past activities has been completed. Industry interviews are in progress and a majority of meetings have been held. Analysis of the information gained is in progress. The preliminary analysis of this information indicates that for appropriate near-term demonstration-type projects, the level of interest for collaboration between DOE and industry is high. The data also identifies issues industry is concerned with which impact the commercialization of hydrogen energy systems.

  20. British Industrial Libraries Before 1939

    ERIC Educational Resources Information Center

    Marshall, Margaret R.

    1972-01-01

    British industrial firm libraries are traced from their beginnings till 1939, by which date they had spread to many branches of industry and had been recognized as an important part of the industrial and library worlds, thus establishing standard patterns of work. The origins and significance of Aslib are discussed. (27 references) (Author/NH)

  1. Technological Change in Regulated Industries.

    ERIC Educational Resources Information Center

    Capron, William M., Ed.

    The articles in this volume discuss how well industries operating under government regulation respond to technical innovation: do the effects of regulations vary among industries, and if so, does this result from variations in the regulatory approach, the organization of the firms, or the nature of the technology? Industries considered include…

  2. [Elementary Grades Program on Industry.

    ERIC Educational Resources Information Center

    Wisconsin Univ. - Stout, Menomonie. Center for Vocational, Technical and Adult Education.

    Prepared as an aid to teachers, the document contains two parts intended to help correlate instruction of industrial arts at the elementary level with the recommended curriculum content in the Wisconsin Guide to Local Curriculum Improvement in Industrial Education, K-12. Pertaining to field objectives 1-4 in the guide, Industry for the Elementary…

  3. Industry-Oriented Doctorate Established.

    ERIC Educational Resources Information Center

    Chemical and Engineering News, 1982

    1982-01-01

    Describes an industry-related program at the University of Texas (Arlington) leading to a Doctorate of Science in Applied Chemistry. The program requires an industrial internship and a dissertation based on research involving both the university's chemistry faculty and chemists in industry. (SK)

  4. The US Cruise Ship Industry.

    ERIC Educational Resources Information Center

    Miller, Willis H.

    1985-01-01

    The cruise ship industry relates directly to many features of the natural and cultural environments. The U.S. cruise ship industry is analyzed. Discusses the size of the industry, precruise passenger liners, current cruise ships, cruise regions and routes, ports of call, major ports, passengers, and future prospects. (RM)

  5. New Books for Industrial Educators

    ERIC Educational Resources Information Center

    School Shop, 1975

    1975-01-01

    The most recent book releases in the field of industrial-technical education are listed alphabetically under: automotive/power mechanics; building trades; drafting; electricity/electronics; graphic arts, industrial arts, vocational, technical and career education; industrial mathematics; machine shop/metalworking; metrics; radio/television;…

  6. The state of the industry

    SciTech Connect

    Kaufmann, E.N. ); Riesen, A.E. ); Shaw, D.T. ); Cannon, P. ); Mead, E. J. and Co., Wilmington, DE . Research and Development Div. )

    1990-01-01

    This article reports on the current state of the superconductor industry. The authors express their opinions regarding industry-wide progress in understanding of and applications for superconductors. The role of the U.S. government in research and development is addressed and the international competition within the superconducting industry is discussed.

  7. SNE Industrial Fieldbus Interface

    NASA Technical Reports Server (NTRS)

    Lucena, Angel; Raines, Matthew; Oostdyk, Rebecca; Mata, Carlos

    2011-01-01

    Programmable logic controllers (PLCs) have very limited diagnostic and no prognostic capabilities, while current smart sensor designs do not have the capability to communicate over Fieldbus networks. The aim is to interface smart sensors with PLCs so that health and status information, such as failure mode identification and measurement tolerance, can be communicated via an industrial Fieldbus such as ControlNet. The SNE Industrial Fieldbus Interface (SIFI) is an embedded device that acts as a communication module in a networked smart sensor. The purpose is to enable a smart sensor to communicate health and status information to other devices, such as PLCs, via an industrial Fieldbus networking protocol. The SNE (Smart Network Element) is attached to a commercial off-the-shelf Any bus-S interface module through the SIFI. Numerous Anybus-S modules are available, each one designed to interface with a specific Fieldbus. Development of the SIFI focused on communications using the ControlNet protocol, but any of the Anybus-S modules can be used. The SIFI communicates with the Any-bus module via a data buffer and mailbox system on the Anybus module, and supplies power to the module. The Anybus module transmits and receives data on the Fieldbus using the proper protocol. The SIFI is intended to be connected to other existing SNE modules in order to monitor the health and status of a transducer. The SIFI can also monitor aspects of its own health using an onboard watchdog timer and voltage monitors. The SIFI also has the hardware to drive a touchscreen LCD (liquid crystal display) unit for manual configuration and status monitoring.

  8. Industrial plasmas in academia

    NASA Astrophysics Data System (ADS)

    Hollenstein, Ch; Howling, AA; Guittienne, Ph; Furno, I.

    2015-01-01

    The present review, written at the occasion of the 2014 EPS Innovation award, will give a short overview of the research and development of industrial plasmas within the last 30 years and will also provide a first glimpse into future developments of this important topic of plasma physics and plasma chemistry. In the present contribution, some of the industrial plasmas studied at the CRPP/EPFL at Lausanne are highlighted and their influence on modern plasma physics and also discharge physics is discussed. One of the most important problems is the treatment of large surfaces, such as that used in solar cells, but also in more daily applications, such as the packaging industry. In this contribution, the advantages and disadvantages of some of the most prominent plasmas such as capacitively- and inductively-coupled plasmas are discussed. Electromagnetic problems due to the related radio frequency and its consequences on the plasma reactor performance, and also dust formation due to chemical reactions in plasma, are highlighted. Arcing and parasitic discharges occurring in plasma reactors can lead to plasma reactor damages. Some specific problems, such as the gas supply of a large area reactor, are discussed in more detail. Other topics of interest have been dc discharges such as those used in plasma spraying where thermal plasmas are applied for advanced material processing. Modern plasma diagnostics make it possible to investigate sparks in electrical discharge machining, which surprisingly show properties of weakly-coupled plasmas. Nanosecond dielectric barrier discharge plasmas have been applied to more speculative topics such as applications in aerodynamics and will surely be important in the future for ignition and combustion. Most of the commonly-used plasma sources have been shown to be limited in their performance. Therefore new, more effective plasma sources are urgently required. With the recent development of novel resonant network antennas for new

  9. Response to Pagano et al.

    PubMed

    Rezende, Flávia; Löwe, Oliver; Helfinger, Valeska; Prior, Kim-Kristin; Walter, Maria; Zukunft, Sven; Fleming, Ingrid; Weissmann, Norbert; Brandes, Ralf P; Schröder, Katrin

    2015-11-20

    In their letter, Pagano et al. appreciate the development of the Nox1, Nox2, and Nox4 triple (3N(-/-)) knockout mouse. They also agree on the view that chemiluminescence assays in general have severe limitations. However, they criticize the fact that the membrane assays in the particular study were restricted to chemiluminescence techniques. Moreover, Pagano et al. got the impression that statements concerning membrane assays of Nox activity in general were made. In addition to a lack of some technical details, Pagano et al. also found the characterization of the 3N(-/-) incomplete and some of the results to be incomprehensible. Although we are grateful for the interest of Pagano et al. in our work, we realized that basically each observation of our study was questioned. This is certainly an excessive rejection of the study in total and fails to appreciate the clear chain of evidences presented. Our work focused on chemiluminescence, and thus, any conclusions are restricted to this technique. Moreover, the 3N(-/-) mice were never developed to study the physiology of Nox enzymes, but rather to validate Nox specificity of NADPH-stimulated chemiluminescence assays. We are convinced that our findings are a valid demonstration that chemiluminescence-based assays in membrane preparations stimulated with NADPH do not measure Nox activity. This conclusion is based on both overexpression studies as well as genetic deficient mouse models. The criticisms of Pagano et al. thus might be justified in some aspects; they, however, cannot disprove the conclusions of our work. Antioxid. Redox Signal. 23, 1247-1249.

  10. Response to Pagano et al.

    PubMed

    Rezende, Flávia; Löwe, Oliver; Helfinger, Valeska; Prior, Kim-Kristin; Walter, Maria; Zukunft, Sven; Fleming, Ingrid; Weissmann, Norbert; Brandes, Ralf P; Schröder, Katrin

    2015-11-20

    In their letter, Pagano et al. appreciate the development of the Nox1, Nox2, and Nox4 triple (3N(-/-)) knockout mouse. They also agree on the view that chemiluminescence assays in general have severe limitations. However, they criticize the fact that the membrane assays in the particular study were restricted to chemiluminescence techniques. Moreover, Pagano et al. got the impression that statements concerning membrane assays of Nox activity in general were made. In addition to a lack of some technical details, Pagano et al. also found the characterization of the 3N(-/-) incomplete and some of the results to be incomprehensible. Although we are grateful for the interest of Pagano et al. in our work, we realized that basically each observation of our study was questioned. This is certainly an excessive rejection of the study in total and fails to appreciate the clear chain of evidences presented. Our work focused on chemiluminescence, and thus, any conclusions are restricted to this technique. Moreover, the 3N(-/-) mice were never developed to study the physiology of Nox enzymes, but rather to validate Nox specificity of NADPH-stimulated chemiluminescence assays. We are convinced that our findings are a valid demonstration that chemiluminescence-based assays in membrane preparations stimulated with NADPH do not measure Nox activity. This conclusion is based on both overexpression studies as well as genetic deficient mouse models. The criticisms of Pagano et al. thus might be justified in some aspects; they, however, cannot disprove the conclusions of our work. Antioxid. Redox Signal. 23, 1247-1249. PMID:26173053

  11. Industrial Needs for ICME

    NASA Astrophysics Data System (ADS)

    Konter, A. W. A.; Farivar, H.; Post, J.; Prahl, U.

    2016-01-01

    The potential of the evolving technology known as integrated computational materials engineering (ICME) is acknowledged by many stakeholders. Good progress has been made in computational tools for both the understanding of the material behavior and the understanding of the structural behavior. Several examples illustrate the potential of a tighter integration between both sciences. Industry is still reluctant to integrate the computational material science developments in its daily structural analysis science, however. The various reasons for this reluctance are indicated in this article, and the coordinated actions to extend the applicability of ICME are discussed. The ICME Expert group is already performing several of these actions to improve application of ICME.

  12. Industrial application experiment series

    NASA Technical Reports Server (NTRS)

    Bluhm, S. A.

    1981-01-01

    Two procurements within the Industrial Application Experiment Series of the Thermal Power Systems Project are discussed. The first procurement, initiated in April 1980, resulted in an award to the Applied Concepts Corporation for the Capital Concrete Experiment: two Fresnel concentrating collectors will be evaluated in single-unit installations at the Jet Propulsion Laboratory Parabolic Dish Test Site and at Capitol Concrete Products, Topeka, Kansas. The second procurement, initiated in March 1981, is titled, "Thermal System Engineering Experiment B." The objective of the procurement is the rapid deployment of developed parabolic dish collectors.

  13. Magnesium industry overview

    SciTech Connect

    Clow, B.B.

    1996-10-01

    Magnesium products provide an excellent strength-to-weight ratio, good fatigue strength, high impact strength, good corrosion resistance, high-speed machinability, and good thermal and electrical conductivities. As a result, applications are expanding in almost every industry. Dozens of automotive components are now made of magnesium, including steering wheels, valve covers, and seat frames. Magnesium alloys are also used in computer housings, in-line roller skates, golf clubs, tennis racquets, and baseball bats. Good strength and stiffness at both room and elevated temperatures make magnesium alloys especially valuable for aerospace applications. This article presents an overview of magnesium technology, world production, increasing demand, and recycling.

  14. Recent developments: Industry briefs

    SciTech Connect

    1990-12-01

    Recent nuclear industry briefs are presented. These briefs include: uranium mine closures; all Ontario new reactor plans halted; B & W and GA form MHTGR fuel joint venture; Namibia seeks uranium sales in Japan; Minatco purchases remainder of Wolly Project; CGE agrees to relinquish control of Framatome; Oregon voter keep Trojan Nuclear Plant open; Soviets invited to Foratom meeting; court overrules NRC in licensing and training issues; Glencar exploration injoint venture with Hungarian mine; Soviet Union and Argentina to cooperate in breeder program; and German loads revive Atucha-2.

  15. Space Coatings for Industry

    NASA Technical Reports Server (NTRS)

    1980-01-01

    Ball Aerospace developed entirely new space lubrication technologies. A new family of dry lubricants emerged from Apollo, specifically designed for long life in space, together with processes for applying them to spacecraft components in microscopically thin coatings. Lubricants worked successfully on seven Orbiting Solar Observatory flights over the span of a decade and attracted attention to other contractors which became Ball customers. The company has developed several hundred variations of the original OSO technology generally designed to improve the quality and useful life of a wide range of products or improve efficiency of the industrial processes by which such products are manufactured.

  16. Recent developments: Industry briefs

    SciTech Connect

    1992-04-01

    This article is the `Industry Briefs` portion of Nuexco`s April 1992 `Recent Developments` section. Items covered in this article include: (1) France`s SILVA enrichment process, (2) 1993 US enrichment prices, (3) relicensing plans for Monticello, (4) a reactor incident at Sosnovy Bor 3, (5) Canadian agreements on Uranium mining, (6) China`s ascession to the Nuclear Non-proliferation Treaty, (7) settlement of the lawsuit between Westinghouse and the Philipines, (8) political reforms on South Africa, and (9) establishment of an international agreement on dual-use export control policy.

  17. Coal industry annual 1996

    SciTech Connect

    1997-11-01

    This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality, and emissions for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States.This report does not include coal consumption data for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. Consumption for nonutility power producers not included in this report is estimated to be 24 million short tons for 1996. 14 figs., 145 tabs.

  18. Coal Industry Annual 1995

    SciTech Connect

    1996-10-01

    This report presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. Consumption for nonutility power producers not included in this report is estimated to be 21 million short tons for 1995.

  19. Space industrialization opportunities

    NASA Technical Reports Server (NTRS)

    Jernigan, C. M. (Editor); Pentecost, E. (Editor)

    1985-01-01

    The current status of efforts to develop commercial space projects is surveyed, with a focus on US programs, in reviews and reports presented at the Second Symposium on Space Industrialization held in Huntsville in February 1984. Areas explored include policy, legal, and economic aspects; communications; materials processing; earth-resources observation; and the role of space carriers and a space station. Also included in the volume are 132 brief descriptions of the NASA Microgravity Science and Applications Program Tasks as of December 1984. These tasks cover the fields electronics materials; solidification of metals, alloys, and composites; fields and transport phenomena; biotechnology; glass and ceramics; combustion science; and experimental technology.

  20. Large rectification magnetoresistance in nonmagnetic Al/Ge/Al heterojunctions.

    PubMed

    Zhang, Kun; Li, Huan-Huan; Grünberg, Peter; Li, Qiang; Ye, Sheng-Tao; Tian, Yu-Feng; Yan, Shi-Shen; Lin, Zhao-Jun; Kang, Shi-Shou; Chen, Yan-Xue; Liu, Guo-Lei; Mei, Liang-Mo

    2015-09-21

    Magnetoresistance and rectification are two fundamental physical properties of heterojunctions and respectively have wide applications in spintronics devices. Being different from the well known various magnetoresistance effects, here we report a brand new large magnetoresistance that can be regarded as rectification magnetoresistance: the application of a pure small sinusoidal alternating-current to the nonmagnetic Al/Ge Schottky heterojunctions can generate a significant direct-current voltage, and this rectification voltage strongly varies with the external magnetic field. We find that the rectification magnetoresistance in Al/Ge Schottky heterojunctions is as large as 250% at room temperature, which is greatly enhanced as compared with the conventional magnetoresistance of 70%. The findings of rectification magnetoresistance open the way to the new nonmagnetic Ge-based spintronics devices of large rectification magnetoresistance at ambient temperature under the alternating-current due to the simultaneous implementation of the rectification and magnetoresistance in the same devices.

  1. Thermodynamic modeling of Pt-Al and Pd-Al

    NASA Astrophysics Data System (ADS)

    Carr, Derek

    2011-03-01

    Pure platinum and pure palladium are too soft for typical jewelry applications. Adding small amounts of other metals can significantly increase their performance. However, international hallmarking standards require the alloys to be 95% pure by weight. How does one achieve significant improvements in performance adding only small amounts (5 wt-%) of other metals? Significant improvements are possible even with small additions if precipitate hardening can be induced. Using a combination of first-principles, cluster expansion, and Monte Carlo modeling, we have identified new Pt-rich/Pd-rich phases in Pt-Al and Pd-Al that should be useful in precipitate hardening. Thermodynamical modeling indicates that the phases are experimentally feasible (not kinetically inhibited).

  2. Large rectification magnetoresistance in nonmagnetic Al/Ge/Al heterojunctions

    NASA Astrophysics Data System (ADS)

    Zhang, Kun; Li, Huan-Huan; Grünberg, Peter; Li, Qiang; Ye, Sheng-Tao; Tian, Yu-Feng; Yan, Shi-Shen; Lin, Zhao-Jun; Kang, Shi-Shou; Chen, Yan-Xue; Liu, Guo-Lei; Mei, Liang-Mo

    2015-09-01

    Magnetoresistance and rectification are two fundamental physical properties of heterojunctions and respectively have wide applications in spintronics devices. Being different from the well known various magnetoresistance effects, here we report a brand new large magnetoresistance that can be regarded as rectification magnetoresistance: the application of a pure small sinusoidal alternating-current to the nonmagnetic Al/Ge Schottky heterojunctions can generate a significant direct-current voltage, and this rectification voltage strongly varies with the external magnetic field. We find that the rectification magnetoresistance in Al/Ge Schottky heterojunctions is as large as 250% at room temperature, which is greatly enhanced as compared with the conventional magnetoresistance of 70%. The findings of rectification magnetoresistance open the way to the new nonmagnetic Ge-based spintronics devices of large rectification magnetoresistance at ambient temperature under the alternating-current due to the simultaneous implementation of the rectification and magnetoresistance in the same devices.

  3. The Implications of Industrial Management for the Administration of Industrial Education Programs

    ERIC Educational Resources Information Center

    White, Michael R.

    1978-01-01

    The paper discusses the functions and principles of industrial management, compares educational and industrial organization, and notes industrial management techniques applicable to industrial education administration. (MF)

  4. AlSb/InAs/AlSb quantum wells

    NASA Technical Reports Server (NTRS)

    Kroemer, Herbert

    1990-01-01

    Researchers studied the InAs/AlSb system recently, obtaining 12nm wide quantum wells with room temperature mobilities up to 28,000 cm(exp 2)/V center dot S and low-temperature mobilities up to 325,000 cm(exp 2)/V center dot S, both at high electron sheet concentrations in the 10(exp 12)/cm(exp 2) range (corresponding to volume concentrations in the 10(exp 18)/cm(exp 2) range). These wells were not intentionally doped; the combination of high carrier concentrations and high mobilities suggest that the electrons are due to not-intentional modulation doping by an unknown donor in the AlSb barriers, presumably a stoichiometric defect, like an antisite donor. Inasmuch as not intentionally doped bulk AlSb is semi-insulating, the donor must be a deep one, being ionized only by draining into the even deeper InAs quantum well. The excellent transport properties are confirmed by other observations, like excellent quantum Hall effect data, and the successful use of the quantum wells as superconductive weak links between Nb electrodes, with unprecendentedly high critical current densities. The system is promising for future field effect transistors (FETs), but many processing problems must first be solved. Although the researchers have achieved FETs, the results so far have not been competitive with GaAs FETs.

  5. Biohydrogen production from industrial wastewaters.

    PubMed

    Moreno-Andrade, Iván; Moreno, Gloria; Kumar, Gopalakrishnan; Buitrón, Germán

    2015-01-01

    The feasibility of producing hydrogen from various industrial wastes, such as vinasses (sugar and tequila industries), and raw and physicochemical-treated wastewater from the plastic industry and toilet aircraft wastewater, was evaluated. The results showed that the tequila vinasses presented the maximum hydrogen generation potential, followed by the raw plastic industry wastewater, aircraft wastewater, and physicochemical-treated wastewater from the plastic industry and sugar vinasses, respectively. The hydrogen production from the aircraft wastewater was increased by the adaptation of the microorganisms in the anaerobic sequencing batch reactor.

  6. Industrial ecology: concepts and approaches.

    PubMed

    Jelinski, L W; Graedel, T E; Laudise, R A; McCall, D W; Patel, C K

    1992-02-01

    Industrial ecology is a new approach to the industrial design of products and processes and the implementation of sustainable manufacturing strategies. It is a concept in which an industrial system is viewed not in isolation from its surrounding systems but in concert with them. Industrial ecology seeks to optimize the total materials cycle from virgin material to finished material, to component, to product, to waste product, and to ultimate disposal. To better characterize the topic, the National Academy of Sciences convened a colloquium from which were derived a number of salient contributions. This paper sets the stage for the contributions that follow and discusses how each fits into the framework of industrial ecology.

  7. Pharma industry in India.

    PubMed

    Sundaram, V M

    2008-01-01

    Globally ranked fourth by volume and 13th in value, the Indian pharma industry is a leading producer of high-quality, low-cost generic drugs. Its 14% share of the USD 57 billion world generic market is expected to increase to 50% by 2010. With the advantages of cost competitiveness, ability and experience in reverse engineering, availability of skilled scientific and engineering personnel and the capability to produce raw materials for a wide range of drugs from the basic stage, the industry delivers the entire range of therapeutic products. McKinsey & Co. predict that India's pharmaceutical market could reach a size of USD 20 billion by 2015, becoming one of the top 10 drug markets in the world. Generic versions of the cardiovascular drug carvedilol, ANDA-approved allopurinol, verapamil SR and the anticancer drug paclitaxel are some of the recent products introduced by Indian companies, with Caraco, Ranbaxy, Dabur, Dr. Reddy's, Nicholas Piramal India, leading the list. Setting up of integrated drug development companies and aggressive entries into the Japanese drug market have provided further impetus to the country's pharma manufacturing arena. PMID:18301810

  8. Industrial Maintenance Strategies

    SciTech Connect

    Sajjad Akbar

    2006-07-01

    Industrial plants have become more complex due to technological advancement. This has made the task of maintenance more difficult. The maintenance costs in terms of resources and downtime loss are so high that maintenance function has become a critical factor in a plant's profitability. Industry should devote as much forethought to the management of maintenance function as to production. Maintenance has grown from an art to a precise, technical engineering science. Planning, organizing scheduling and control of maintenance using modern techniques pays dividends in the form of reduced costs and increased reliability. The magnitude and the dimension of maintenance have multiplied due to development in the engineering technologies. Production cost and capacities are directly affected by the breakdown time. Total operating cost including the maintenance cost plays an important role in replacement dimension. The integrated system approach would bring forth the desired results of high maintenance standards. The standards once achieved and sustained, would add to the reliability of the plan and relieve heavy stresses and strains on the engineering logistic support. (author)

  9. 2013 mask industry survey

    NASA Astrophysics Data System (ADS)

    Malloy, Matt

    2013-09-01

    A comprehensive survey was sent to merchant and captive mask shops to gather information about the mask industry as an objective assessment of its overall condition. 2013 marks the 12th consecutive year for this process. Historical topics including general mask profile, mask processing, data and write time, yield and yield loss, delivery times, maintenance, and returns were included and new topics were added. Within each category are multiple questions that result in a detailed profile of both the business and technical status of the mask industry. While each year's survey includes minor updates based on feedback from past years and the need to collect additional data on key topics, the bulk of the survey and reporting structure have remained relatively constant. A series of improvements is being phased in beginning in 2013 to add value to a wider audience, while at the same time retaining the historical content required for trend analyses of the traditional metrics. Additions in 2013 include topics such as top challenges, future concerns, and additional details in key aspects of mask masking, such as the number of masks per mask set per ground rule, minimum mask resolution shipped, and yield by ground rule. These expansions beyond the historical topics are aimed at identifying common issues, gaps, and needs. They will also provide a better understanding of real-life mask requirements and capabilities for comparison to the International Technology Roadmap for Semiconductors (ITRS).

  10. Computer Technology for Industry

    NASA Technical Reports Server (NTRS)

    1979-01-01

    In this age of the computer, more and more business firms are automating their operations for increased efficiency in a great variety of jobs, from simple accounting to managing inventories, from precise machining to analyzing complex structures. In the interest of national productivity, NASA is providing assistance both to longtime computer users and newcomers to automated operations. Through a special technology utilization service, NASA saves industry time and money by making available already developed computer programs which have secondary utility. A computer program is essentially a set of instructions which tells the computer how to produce desired information or effect by drawing upon its stored input. Developing a new program from scratch can be costly and time-consuming. Very often, however, a program developed for one purpose can readily be adapted to a totally different application. To help industry take advantage of existing computer technology, NASA operates the Computer Software Management and Information Center (COSMIC)(registered TradeMark),located at the University of Georgia. COSMIC maintains a large library of computer programs developed for NASA, the Department of Defense, the Department of Energy and other technology-generating agencies of the government. The Center gets a continual flow of software packages, screens them for adaptability to private sector usage, stores them and informs potential customers of their availability.

  11. Identification of Candida albicans ALS2 and ALS4 and Localization of Als Proteins to the Fungal Cell Surface

    PubMed Central

    Hoyer, L. L.; Payne, T. L.; Hecht, J. E.

    1998-01-01

    Additional genes in the growing ALS family of Candida albicans were isolated by PCR screening of a genomic fosmid library with primers designed from the consensus tandem-repeat sequence of ALS1. This procedure yielded fosmids encoding ALS2 and ALS4. ALS2 and ALS4 conformed to the three-domain structure of ALS genes, which consists of a central domain of tandemly repeated copies of a 108-bp motif, an upstream domain of highly conserved sequences, and a domain of divergent sequences 3′ of the tandem repeats. Alignment of five predicted Als protein sequences indicated conservation of N- and C-terminal hydrophobic regions which have the hallmarks of secretory signal sequences and glycosylphosphatidylinositol addition sites, respectively. Heterologous expression of an N-terminal fragment of Als1p in Saccharomyces cerevisiae demonstrated function of the putative signal sequence with cleavage following Ala17. This signal sequence cleavage site was conserved in the four other Als proteins analyzed, suggesting identical processing of each protein. Primary-structure features of the five Als proteins suggested a cell-surface localization, which was confirmed by indirect immunofluorescence with an anti-Als antiserum. Staining was observed on mother yeasts and germ tubes, although the intensity of staining on the mother yeast decreased with elongation of the germ tube. Similar to other ALS genes, ALS2 and ALS4 were differentially regulated. ALS4 expression was correlated with the growth phase of the culture; ALS2 expression was not observed under many different in vitro growth conditions. The data presented here demonstrate that ALS genes encode cell-surface proteins and support the conclusion that the size and number of Als proteins on the C. albicans cell surface vary with strain and growth conditions. PMID:9765564

  12. Network structure of inter-industry flows

    NASA Astrophysics Data System (ADS)

    McNerney, James; Fath, Brian D.; Silverberg, Gerald

    2013-12-01

    We study the structure of inter-industry relationships using networks of money flows between industries in 45 national economies. We find these networks vary around a typical structure characterized by a Weibull link weight distribution, exponential industry size distribution, and a common community structure. The community structure is hierarchical, with the top level of the hierarchy comprising five industry communities: food industries, chemical industries, manufacturing industries, service industries, and extraction industries.

  13. Al-Anon and recovery.

    PubMed

    Cermak, T L

    1989-01-01

    The history of Al-Anon and its current demographics are reviewed. In order to understand 12-step recovery and psychotherapy for family members of alcoholics, the concept of codependence is defined with a set of diagnostic criteria consistent with the DSM-III-R definition of personality traits and disorders. At the core of codependence are denial and an unrealistic relationship to willpower. The therapeutic implications of considering codependence as a personality disorder are explored, as are the characteristics that make codependence unique among personality disorders: the central role of denial and the existence of a self-help organization to facilitate recovery. The dynamics of working the 12 steps on codependent characteristics are outlined. A synergistic relationship between psychotherapy and the 12 steps is described. Special attention is given the emergence of Al-Anon adult children of alcoholic meetings, and the future of codependence is discussed.

  14. Green biorefinery - Industrial implementation.

    PubMed

    Kamm, B; Schönicke, P; Hille, Ch

    2016-04-15

    Oil refineries currently generate a multitude of products for almost every sphere of life at very high efficiency. However, fossil raw materials are just available in limited quantities. The development of comparable BIOREFINERIES is necessary to make a variety of competitive biological products regarding their equivalent products based on fossil raw materials. The product range of a biorefinery comprises products that can be manufactured on the basis of crude oil, as well as such products that cannot be produced on the basis of crude oil (Kamm, Gruber, & Kamm, 2011). GREEN BIOREFINERIES [GBR's] are complex systems of sustainable, environment- and resource-friendly technologies for a comprehensive material and energy use or recovery of renewable raw materials in form of green and waste biomasses from a sustainable land use as target (Kamm et al., 2009; Digman, Runge, Shinners, & Hatfield, 2013). PMID:26675876

  15. Green biorefinery - Industrial implementation.

    PubMed

    Kamm, B; Schönicke, P; Hille, Ch

    2016-04-15

    Oil refineries currently generate a multitude of products for almost every sphere of life at very high efficiency. However, fossil raw materials are just available in limited quantities. The development of comparable BIOREFINERIES is necessary to make a variety of competitive biological products regarding their equivalent products based on fossil raw materials. The product range of a biorefinery comprises products that can be manufactured on the basis of crude oil, as well as such products that cannot be produced on the basis of crude oil (Kamm, Gruber, & Kamm, 2011). GREEN BIOREFINERIES [GBR's] are complex systems of sustainable, environment- and resource-friendly technologies for a comprehensive material and energy use or recovery of renewable raw materials in form of green and waste biomasses from a sustainable land use as target (Kamm et al., 2009; Digman, Runge, Shinners, & Hatfield, 2013).

  16. Robots in modern industry

    NASA Technical Reports Server (NTRS)

    Heer, E.

    1981-01-01

    A survey is presented of robotic device types and capabilities, and an assessment is made of the relative benefits they confer in present and planned numbers on such industrial countries as Japan, the U.S., and West Germany. Attention is also given to possible social impacts of large-scale implementation, and the need for close consultation between management and labor is stressed. It is reported that, while the hourly cost of robot labor remained at between $4.00 and $4.60 over the period 1960-present, human hourly labor costs (including fringe benefits) have risen from less than $4.00 to nearly $17.00. Among the types of devices described are: (1) remotely controlled manipulator vehicles; (2) undersea robotic craft; (3) servo-controlled robots; and (4) articulated robots. Also covered are robot programming languages derived from such standard languages as ALGOL, FORTRAN, and BASIC.

  17. Industrial Inspection System

    NASA Technical Reports Server (NTRS)

    1993-01-01

    Lixi, Inc. has built a thriving business on NASA-developed x-ray technology. The Low Intensity X-ray Imaging scope (LIXI) was designed to use less than one percent of radiation required by conventional x-ray devices. It is portable and can be used for a variety of industrial inspection systems as well as medical devices. A food processing plant uses the new LIXI Conveyor system to identify small bone fragments in chicken. The chicken packages on a conveyor belt enter an x-ray chamber and the image is displayed on a monitor. Defects measuring less than a millimeter can be detected. An important advantage of the system is its ability to inspect 100 percent of the product right on the production line.

  18. Industrial Lung Cancer

    PubMed Central

    Fitch, Maxwell

    1982-01-01

    There are many known chemical and physical causes of industrial lung cancer. Their common feature is a long latent period—usually ten to 40 years—between initial exposure to the carcinogen and clinical recognition of the lesion. Occupationally induced lung cancer is indistinguishable from lung cancer of unknown etiology or that caused by cigaret smoking. Smoking alone is responsible for a very large proportion of all lung cancer and it potentiates the effect of most other carcinogens. Most cases of lung cancer in the next 20-30 years will be the result of exposures which have already occurred. In these cases, early diagnosis of pre-invasive resectable lesions offers the only hope for prolonging life. PMID:21286559

  19. The Canadian Beef Industry

    PubMed Central

    Fredeen, H.

    1980-01-01

    The cattle industry in Canada has changed greatly over the past several decades. Size of the national dairy herd has reduced steadily but this reduction has been more than offset by an increase in the beef herd. As the dairy herd has decreased, the role of the Holstein has increased. The genetic improvement of the Canadian Holstein, based on selection procedures emphasizing progeny performance and mediated through increasing use of artificial insemination, has earned the breed a strong international reputation. This is reflected by the increasing international demand for semen. The strongest growth of the national beef herd occurred during a period of brisk import activity. Several of the new nonBritish breeds are now well established. Their advent on the Canadian scene rekindled interest in crossbreeding and systematic crossbreeding programs designed to make controlled use of heterozygosity are in the process of development. The new breeds of major importance at this time combine rapid growth rate with desirable carcass characteristics, specifically lean content. This, coupled with the carcass grade standards inaugurated in 1972, has resulted in improved efficiency of lean meat production. Importation activity has waned and a review of the production credentials of breeds not yet in Canada suggests little likelihood that they will contribute meaningfully to Canadian production. The numerous beef breeds now in Canada are presently undergoing a process of applied evaluation and relatively few of them seem destined to make a lasting contribution. The future of the cattle industry will be determined largely by economic developments. However, the ability of the ruminant to utilize food materials that do not compete directly with human demands should ensure an enduring future. PMID:7363257

  20. Industrial scale gene synthesis.

    PubMed

    Notka, Frank; Liss, Michael; Wagner, Ralf

    2011-01-01

    The most recent developments in the area of deep DNA sequencing and downstream quantitative and functional analysis are rapidly adding a new dimension to understanding biochemical pathways and metabolic interdependencies. These increasing insights pave the way to designing new strategies that address public needs, including environmental applications and therapeutic inventions, or novel cell factories for sustainable and reconcilable energy or chemicals sources. Adding yet another level is building upon nonnaturally occurring networks and pathways. Recent developments in synthetic biology have created economic and reliable options for designing and synthesizing genes, operons, and eventually complete genomes. Meanwhile, high-throughput design and synthesis of extremely comprehensive DNA sequences have evolved into an enabling technology already indispensable in various life science sectors today. Here, we describe the industrial perspective of modern gene synthesis and its relationship with synthetic biology. Gene synthesis contributed significantly to the emergence of synthetic biology by not only providing the genetic material in high quality and quantity but also enabling its assembly, according to engineering design principles, in a standardized format. Synthetic biology on the other hand, added the need for assembling complex circuits and large complexes, thus fostering the development of appropriate methods and expanding the scope of applications. Synthetic biology has also stimulated interdisciplinary collaboration as well as integration of the broader public by addressing socioeconomic, philosophical, ethical, political, and legal opportunities and concerns. The demand-driven technological achievements of gene synthesis and the implemented processes are exemplified by an industrial setting of large-scale gene synthesis, describing production from order to delivery.

  1. Effect of shot peening and grain refinement on the fatigue life and strength of commercially pure Al and two of its alloys: Al-2024-T3 and Al-7075-T6

    NASA Astrophysics Data System (ADS)

    Qandil, A.; Zaid, Adnan I. O.

    2016-08-01

    Aluminum and its alloys are widely used materials in automobile, aircraft and space craft industries due to their high strength- to- weight ratio and corrosion resistance beside their other useful properties. They are the second materials in use after steel alloys. Most of the failures in parts of aircrafts and space vehicles are mainly caused by fatigue and stress corrosion cracking. In this paper, the effect of shot peening on the fatigue life of commercially pure aluminumand two of its alloys namely:Al-2024 and Al-7075-T6 is presented and discussed. Furthermore, the effect of addition of vanadium to Al and Al grain refined by Ti and Ti+Bon Its fatigue life and strengthis also presented and discussed using scanning electron microscope, SEM. It was that shot peening and the addition of V toAl and Al onAl grain refined by Ti and Ti+B have resulted in enhancement of the fatigue life and strength. Ffinally, the effect of shot peening on the surface quality of the peened parts is also presented and discussed.

  2. Research Projects in Industrial Technology.

    SciTech Connect

    United States. Bonneville Power Administration. Industrial Technology Section.

    1990-06-01

    The purpose of this booklet is to briefly describe ongoing and completed projects being carried out by Bonneville Power Administration's (BPA) Industrial Technology Section. In the Pacific Northwest, the industrial sector is the largest of the four consuming sectors. It accounted for thirty-nine percent of the total firm demand in the region in 1987. It is not easy to asses the conservation potential in the industrial sector. Recognizing this, the Northwest Power Planning Council established an objective to gain information on the size, cost, and availability of the conservation resource in the industrial sector, as well as other sectors, in its 1986 Power Plan. Specifically, the Council recommended that BPA operate a research and development program in conjunction with industry to determine the potential costs and savings from efficiency improvements in industrial processes which apply to a wide array of industrial firms.'' The section, composed of multidisciplinary engineers, provides technical support to the Industrial Programs Branch by designing and carrying out research relating to energy conservation in the industrial sector. The projects contained in this booklet are arranged by sector --industrial, utility, and agricultural -- and, within each sector, chronologically from ongoing to completed, with those projects completed most recently falling first. For each project the following information is given: its objective approach, key findings, cost, and contact person. Completed projects also include the date of completion, a report title, and report number.

  3. Emerging mechanisms of molecular pathology in ALS.

    PubMed

    Peters, Owen M; Ghasemi, Mehdi; Brown, Robert H

    2015-05-01

    Amyotrophic lateral sclerosis (ALS) is a devastating degenerative disease characterized by progressive loss of motor neurons in the motor cortex, brainstem, and spinal cord. Although defined as a motor disorder, ALS can arise concurrently with frontotemporal lobal dementia (FTLD). ALS begins focally but disseminates to cause paralysis and death. About 10% of ALS cases are caused by gene mutations, and more than 40 ALS-associated genes have been identified. While important questions about the biology of this disease remain unanswered, investigations of ALS genes have delineated pathogenic roles for (a) perturbations in protein stability and degradation, (b) altered homeostasis of critical RNA- and DNA-binding proteins, (c) impaired cytoskeleton function, and (d) non-neuronal cells as modifiers of the ALS phenotype. The rapidity of progress in ALS genetics and the subsequent acquisition of insights into the molecular biology of these genes provide grounds for optimism that meaningful therapies for ALS are attainable. PMID:25932674

  4. Determinant factors of industrial symbiosis: greening Pasir Gudang industrial park

    NASA Astrophysics Data System (ADS)

    Teh, B. T.; Ho, C. S.; Matsuoka, Y.; Chau, L. W.; Gomi, K.

    2014-02-01

    Green industry has been identified as an important element in attaining greater sustainability. It calls for harmonizing robust economic growth with environment protection. Industries, particularly in developing and transitional nations such as Malaysia, are in need of a reform. Many experts and international organizations suggest the concept of industrial symbiosis. Mainly, there are successful cases of industrial symbiosis practices around the world. However, there are numerous cases of failure too. As industrial symbiosis is an emerging new approach, with a short history of two decades, a lot of researches are generally focused on narrow context and technical details. There is a lack of concerted efforts to look into the drivers and barriers of industrial symbiosis across different cases. This paper aims to examine the factors influencing the development of industrial symbiosis from various countries to supports such networks to evolve in Pasir Gudang. The findings show institution, law and regulation, finance, awareness and capacity building, technology, research and development, information, collaboration, market, geography proximity, environmental issues and industry structure affect the formation of industrial symbiosis.

  5. 75 FR 77564 - Tart Cherries Grown in the States of Michigan, et al.;

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-12-13

    ... Agricultural Marketing Service 7 CFR Part 930 Tart Cherries Grown in the States of Michigan, et al.; Final Free... strengthen market conditions. The percentages were recommended by the Cherry Industry Administrative Board... handling of tart cherries grown in the States of Michigan, New York, Pennsylvania, Oregon, Utah,...

  6. Synthesis of AlN/Al Polycrystals along with Al Nanoparticles Using Thermal Plasma Route

    SciTech Connect

    Kanhe, Nilesh S.; Nawale, A. B.; Kulkarni, N. V.; Bhoraskar, S. V.; Mathe, V. L.; Das, A. K.

    2011-07-15

    This paper for the first time reports the (200) oriented growth of hexagonal Aluminum nitride crystals during synthesis of aluminum nanoparticles in dc transferred arc thermal plasma reactor by gas phase condensation in nitrogen plasma. The structural and morphological study of as synthesized AlN crystal and aluminium nanoparticles was done by using the x-ray diffraction method, scanning electron microscopy and transmission electron microscopy.

  7. Agriculture--Industry of the Future

    SciTech Connect

    2001-01-23

    This 8-page brochure describes the Office of Industrial Technologies' Agriculture Industry of the Future, a partnership between the Department of Energy and the agriculture industry established to increase industrial energy and cost efficiency.

  8. Petroleum--Industry of the Future

    SciTech Connect

    2001-01-23

    This 8-page brochure describes the Office of Industrial Technologies' Petroleum Industry of The Future, a partnership between the Department of Energy and the petroleum refining industry established to increase industrial energy and cost efficiency.

  9. Ab initio modeling of zincblende AlN layer in Al-AlN-TiN multilayers

    DOE PAGESBeta

    Yadav, S. K.; Wang, J.; Liu, X. -Y.

    2016-06-13

    An unusual growth mechanism of metastable zincblende AlN thin film by diffusion of nitrogen atoms into Al lattice is established. Using first-principles density functional theory, we studied the possibility of thermodynamic stability of AlN as a zincblende phase due to epitaxial strains and interface effect, which fails to explain the formation of zincblende AlN. We then compared the formation energetics of rocksalt and zincblende AlN in fcc Al through direct diffusion of nitrogen atoms to Al octahedral and tetrahedral interstitials. Furthermore, the formation of a zincblende AlN thin film is determined to be a kinetically driven process, not a thermodynamicallymore » driven process.« less

  10. Space industrialization: A national perspective

    NASA Technical Reports Server (NTRS)

    Reis, V. H.

    1984-01-01

    Space industrialization (or commercialization) has the potential to be a major player in America's space program. If this potential is to be realized, however, industrialization efforts must be considered within the context of the other major portions of the space program: shuttle, space station, and civil remote sensing. Further, development efforts must be based upon a sound scientific and technical understanding of the products and processes, and there must be a trained cadre of dedicated individuals willing to devote time and effort to this effort. There remain considerable risks and uncertainties. Given all this, the best path to follow would seem to be a long term, balanced commitment, emphasizing government, industry, and academia partnerships. Several points are addressed: (1) the place of space industrialization in the overall national space program; (2) the meaning of space industrialization with respect to the historic, national aims of space; and (3) specifically what is being industrialized.

  11. Financial risk of the biotech industry versus the pharmaceutical industry.

    PubMed

    Golec, Joseph; Vernon, John A

    2009-01-01

    The biotech industry now accounts for a substantial and growing proportion of total R&D spending on new medicines. However, compared with the pharmaceutical industry, the biotech industry is financially fragile. This article illustrates the financial fragility of the biotech and pharmaceutical industries in the US and the implications of this fragility for the effects that government regulation could have on biotech firms. Graphical analysis and statistical tests were used to show how the biotech industry differs from the pharmaceutical industry. The two industries' characteristics were measured and compared, along with various measures of firms' financial risk and sensitivity to government regulation. Data from firms' financial statements provided accounting-based measures and firms' stock returns applied to a multifactor asset pricing model provided financial market measures. The biotech industry was by far the most research-intensive industry in the US, averaging 38% R&D intensity (ratio of R&D spending to total firm assets) over the past 25 years, compared with an average of 25% for the pharmaceutical industry and 3% for all other industries. Biotech firms exhibited lower and more volatile profits and higher market-related and size-related risk, and they suffered more negative stock returns in response to threatened government price regulation. Biotech firms' financial risks increase their costs of capital and make them more sensitive to government regulations that affect their financial prospects. As biotech products grow to represent a larger share of new medicines, general stock market conditions and government regulations could have a greater impact on the level of innovation of new medicines.

  12. Synthesis of Al-Al2O3 and Al-Aln Nanoparticle Composites Via Electric Explosion of Wires

    NASA Astrophysics Data System (ADS)

    Lerner, M. I.; Lozhkomoev, A. S.; Pervikov, A. V.; Bakina, O. V.

    2016-07-01

    Composite Al-Al2O3 and Al-AlN nanoparticles were synthesized via electric explosion of aluminum wires in an argon-oxygen gas mixture and in nitrogen. The parameters of electric explosion and gas medium affect the size and relative content of nitride and aluminum oxide in the nanoparticles. Processes of forming chemical compounds during aluminum oxidation at the contact surface between explosive products and gas and of nitrogen diffusions into the nanoparticles of the condensed phase are considered.

  13. Occupational lung diseases in the industrializing and industrialized world due to modern industries and modern pollutants.

    PubMed

    Schenker, M

    1992-02-01

    Although most new 'high tech' industrial processes are developed in industrialized countries, many of these technologies are eventually transferred to the industrializing countries. Many of these new technologies are associated with the use of respiratory toxins. However, there has been little study of acute or chronic health effects of work in these industries. The semiconductor industry illustrates many of these issues. The past decade has been increasing globalization of semiconductor manufacturing. Semiconductor manufacturing uses many chemicals with extremely high respiratory toxicity, including gases such as arsine and phosphine, strong acids and bases, dopants and photoactive chemicals. In semiconductor manufacturing, gases and chemicals are strictly controlled, but little is known about the occurrence of respiratory symptoms or disease in this industry. Potential acute respiratory effects of these exposures include mucous membrane irritation, tracheobronchitis, pulmonary edema and death. Chronic effects may include airway sensitization and possibly respiratory cancer. Movement of 'high tech' industries to less industrialized countries may not be accompanied by the same degree of attention to the control of workplace exposures. The shortage of adequately trained health and safety personnel, greater attention to safety than to health issues, and the unorganized and unskilled workforce in industrializing countries may exacerbate this situation. More research is needed on the health effects of exposures in rapidly changing industries such as semiconductor manufacturing, and the results of this research must be communicated and safe practices implemented worldwide.

  14. NiAl-base composite containing high volume fraction of AlN for advanced engines

    NASA Technical Reports Server (NTRS)

    Hebsur, Mohan (Inventor); Whittenbeger, John D. (Inventor); Lowell, Carl F. (Inventor)

    1994-01-01

    A particulate reinforced NiAl-AlN composite alloy has a NiAl matrix and greater than about 13 volume percent fine particles of AlN within the matrix. The particles preferably have a diameter from about 15 nanometers to about 50 nanometers. The particulate reinforced NiAl-AlN composite alloy may be prepared by cryomilling prealloyed NiAl in liquid nitrogen using grinding media having a diameter of from about 2 to 6 mm at an impeller speed of from about 450 RPM to about 800 RPM. The cryomilling may be done for a duration of from about 4 hours to about 20 hours to obtain a cryomilled powder. The cryomilled powder may be consolidated to form the particulate reinforced NiAl-AlN composite alloy. The particulate reinforced alloy can further include a toughening alloy. The toughening alloy may include NiCrAlY, FeCrAlY, and FeAl.

  15. Industrial Safety and Accidents Prevention

    SciTech Connect

    Sajjad Akbar

    2006-07-01

    Accident Hazards, dangers, losses and risk are what we would to like to eliminate, minimize or avoid in industry. Modern industries have created many opportunities for these against which man's primitive instincts offer no protection. In today's complex industrial environment safety has become major preoccupation, especially after the realization that there is a clear economic incentive to do so. Industrial hazards may cause by human error or by physical or mechanical malfunction, it is very often possible to eliminate the worst consequences of human error by engineering modification. But the modification also needs checking very thoroughly to ensue that it has not introduced some new and unsuspected hazard. (author)

  16. Space industrialization studies - An overview

    NASA Technical Reports Server (NTRS)

    Priest, C.; Bradford, R.

    1977-01-01

    An overview of NASA's current planning for a space industrialization program is described as an introduction to the papers on Space Industrialization being presented by Rockwell International Corporation and Science Applications Incorporated. Background information is presented that outlines the integrated planning process which resulted in specific long range goals and objectives being formulated for NASA programs in technology, environment, resources, earth science, communications, space exploration, aeronautics, and an expanded application of space called space industrialization. Program objectives for NASA's Industrialization of Space and studies on potential near term supporting elements (Space Platform, Large Space Structures, Orbital Operations Capabilities Development, Space Manufacturing Module) are discussed.

  17. Industrial Hygiene Issues

    NASA Technical Reports Server (NTRS)

    Brisbin, Steven G.

    1999-01-01

    This breakout session is a traditional conference instrument used by the NASA industrial hygiene personnel as a method to convene personnel across the Agency with common interests. This particular session focused on two key topics, training systems and automation of industrial hygiene data. During the FY 98 NASA Occupational Health Benchmarking study, the training system under development by the U.S. Environmental Protection Agency (EPA) was deemed to represent a "best business practice." The EPA has invested extensively in the development of computer based training covering a broad range of safety, health and environmental topics. Currently, five compact disks have been developed covering the topics listed: Safety, Health and Environmental Management Training for Field Inspection Activities; EPA Basic Radiation Training Safety Course; The OSHA 600 Collateral Duty Safety and Health Course; and Key program topics in environmental compliance, health and safety. Mr. Chris Johnson presented an overview of the EPA compact disk-based training system and answered questions on its deployment and use across the EPA. This training system has also recently been broadly distributed across other Federal Agencies. The EPA training system is considered "public domain" and, as such, is available to NASA at no cost in its current form. Copies of the five CD set of training programs were distributed to each NASA Center represented in the breakout session. Mr. Brisbin requested that each NASA Center review the training materials and determine whether there is interest in using the materials as it is or requesting that EPA tailor the training modules to suit NASA's training program needs. The Safety, Health and Medical Services organization at Ames Research Center has completed automation of several key program areas. Mr. Patrick Hogan, Safety Program Manager for Ames Research Center, presented a demonstration of the automated systems, which are described by the following: (1) Safety

  18. Industrial laser marketplace

    NASA Astrophysics Data System (ADS)

    Belforte, David A.

    1990-05-01

    Introduction: Gary Forrest As with medical, we have a specific individual, Dave Belforte, who, in addition to writing for Laser Focus, publishes with Laser Focus the Industrial Laser Review. Again, this is an area that has some really unique aspects to it which is why we have a specialist at the magazine who tracks this as well as having his own business interests. I just have one quick example. One of the things that I've noticed and I've put this in your handout is it's always interesting to me to see why how the lasers actually impact on finished goods that people buy. So I just clipped out one recent article that mentions some of the different areas when lasers are used in automotive production. There's an ad for the Infinity car of course they've had a strange ad program anyway, but the latest version is "Look at the paint." It's a super high gloss paint. I know in Japan, what I would call laser priming, the use of laser in surface preparation of the metal to obtain a super high gloss is something that's become popular. Now I don't know whether the Infinity is using that or not but it's another example as Moe Levitt indicated earlier lasers have moved into the industrial segment maybe not in the volume that people would like but in a quality sense that is definitely starting to have an impact on the people who are buying those finished products. So I'll give you Dave for the details. David Belforte: The answer is yes, the Infinity has a body which has been processed in what is called laser texturizing process. In Japan, it's known as a mirror finish, and it's not actually applied to the steel of the car. It's a texturizing process on the rolls that reduce the steel down to body thickness. They emboss on that steel a regular pattern which tends to trap radiated light and reflect it back to your eye in a much more intense pattern to give you what appears to be brighter paint. But that was not developed in Japan. It was developed in Belgium actually.

  19. Reply to Pachai et al.

    PubMed

    Harrison, William J; Bex, Peter J

    2016-05-01

    Peripheral vision is fundamentally limited by the spacing between objects. When asked to report a target's identity, observers make erroneous reports that sometimes match the identity of a nearby distractor and sometimes match a combination of target and distractor features. The classification of these errors has previously been used to support competing 'substitution' [1] or 'averaging' [2] models of the phenomenon known as 'visual crowding'. We recently proposed a single model in which both classes of error occur because observers make their reports by sampling from a biologically-plausible population of weighted responses within a region of space around the target [3]. It is critical to note that there is no probabilistic substitution or averaging process in our model; instead, we argue that neither substitution nor averaging occur, but that these are misclassifications of the distribution of reports that emerge when a population response distribution is sampled. This is a fundamentally different way of thinking about crowding, and on this basis we claim to have provided a mechanism unifying categorically distinct perceptual errors. Our goal was not to model all crowding phenomena, such as the release from crowding when target and flanks differ in color or depth [4]. Pachai et al.[5] have suggested that our model is not unifying because it inaccurately predicts perceptual performance for a particular stimulus. Although we agree that our model does not predict their data, this specific demonstration overlooks the critical aspect of the model: perceptual reports are drawn from a weighted population code. We show that Pachai et al.'s [5] own data actually provide evidence for the population code we have described [3], and we suggest a biologically-plausible analysis of their stimuli that provides a computational basis for their 'grouping' account of crowding. PMID:27166690

  20. Reply to Pachai et al.

    PubMed

    Harrison, William J; Bex, Peter J

    2016-05-01

    Peripheral vision is fundamentally limited by the spacing between objects. When asked to report a target's identity, observers make erroneous reports that sometimes match the identity of a nearby distractor and sometimes match a combination of target and distractor features. The classification of these errors has previously been used to support competing 'substitution' [1] or 'averaging' [2] models of the phenomenon known as 'visual crowding'. We recently proposed a single model in which both classes of error occur because observers make their reports by sampling from a biologically-plausible population of weighted responses within a region of space around the target [3]. It is critical to note that there is no probabilistic substitution or averaging process in our model; instead, we argue that neither substitution nor averaging occur, but that these are misclassifications of the distribution of reports that emerge when a population response distribution is sampled. This is a fundamentally different way of thinking about crowding, and on this basis we claim to have provided a mechanism unifying categorically distinct perceptual errors. Our goal was not to model all crowding phenomena, such as the release from crowding when target and flanks differ in color or depth [4]. Pachai et al.[5] have suggested that our model is not unifying because it inaccurately predicts perceptual performance for a particular stimulus. Although we agree that our model does not predict their data, this specific demonstration overlooks the critical aspect of the model: perceptual reports are drawn from a weighted population code. We show that Pachai et al.'s [5] own data actually provide evidence for the population code we have described [3], and we suggest a biologically-plausible analysis of their stimuli that provides a computational basis for their 'grouping' account of crowding.

  1. Industrial ion source technology

    NASA Technical Reports Server (NTRS)

    Kaufman, H. R.; Robinson, R. S.

    1978-01-01

    An analytical model was developed to describe the development of a coned surface texture with ion bombardment and simultaneous deposition of an impurity. A mathematical model of sputter deposition rate from a beveled target was developed in conjuction with the texturing models to provide an important input to that model. The establishment of a general procedure that will allow the treatment of manay different sputtering configurations is outlined. Calculation of cross sections for energetic binary collisions was extened to Ar, Kr.. and Xe with total cross sections for viscosity and diffusion calculated for the interaction energy range from leV to 1000eV. Physical sputtering and reactive ion etching experiments provided experimental data on the operating limits of a broad beam ion source using CF4 as a working gas to produce reactive species in a sputtering beam. Magnetic clustering effects are observed when Al is seeded with Fe and sputtered with Ar(?) ions. Silicon was textured at a micron scale by using a substrate temperature of 600 C.

  2. General Industrial Electronics. Oklahoma Trade and Industrial Education.

    ERIC Educational Resources Information Center

    Harwick, Jim; Siebert, Leo

    This curriculum guide, part of a series of curriculum guides dealing with industrial electricity and electronics, is designed for use in teaching a course in general industrial electronics. Covered in the first half of the guide are units on the following electronic components: semiconductors, solid-state diodes, bipolar transistors, and special…

  3. Plasmonics for the industry

    NASA Astrophysics Data System (ADS)

    Lütolf, Fabian; Basset, Guillaume; Casari, Daniele; Luu-Dinh, Angélique; Gallinet, Benjamin

    2015-08-01

    Metallic nanostructures interact strongly with light through surface plasmon modes and many application fields have been proposed during the past decade, including light harvesting, sensing and structural colors. However, their implementation for the industry requires the development of up scalable and cost effective manufacturing processes. The fabrication at wafer scale of plasmonic nanostructures and metamaterials using nano imprint lithography is reported. After structuring, the evaporation of various plasmonic materials are performed with a tilt angle with respect to the substrate, which increases the light interactions with the different metallic layers as well as enlarges the design possibilities. A step and repeat process is used to increase further the area of nanostructured surface. The measured optical properties of the fabricated structures show a very good agreement compared to numerical calculations using the rigorous coupled wave analysis. These numerical calculations together which structural characterization, increase the process control and enable the design of the nanostructures for specific applications. In particular, nanostructures with a shape similar to split ring resonators and which support high order plasmonic modes showing Fano resonances are shown to be promising for sensing applications. The structures were designed in such a way to have a strong spectral response in the blue/green region of the visible spectrum. Examples of refractive index sensors and stretch sensors were finally discussed.

  4. Tapping private industry.

    PubMed

    Weerakoon, B

    1986-12-01

    Many firms throughout Japan and around the world have come to realize that family planning is good for employee morale and company profits. Japanese and Indian efforts prove that family planning programs not only bring welfare benefits to workers, but commercial advantages to businesses. Because workers' family welfare is closely linked to labor welfare and productivity, the trade union movement has started to become active in promoting family planning activities. Factory-based family planning programs have often cut pregnancy rates in half. Godrej Enterprises of India started promoting family planning in 1957; it provides a model of how family planning has been incorporated into a comprehensive employee welfare system in a factory complex on the outskirts of Bombay, where about 1/2 the workers live in high-rise apartments in the company township of Pirojsha Nagar. Similar programs are presented in India, Thailand, Indonesia, Jamaica, Guatemala, Colombia, Korea, and Turkey. Limiting family size enriches workers' lives and improves the quality of the workforce. The International Labor Organization, through its Workers' Education Program on Population, has played an important role in stimulating industrial sector interest in family planning throughout the world.

  5. Industrial robot's vision systems

    NASA Astrophysics Data System (ADS)

    Iureva, Radda A.; Raskin, Evgeni O.; Komarov, Igor I.; Maltseva, Nadezhda K.; Fedosovsky, Michael E.

    2016-03-01

    Due to the improved economic situation in the high technology sectors, work on the creation of industrial robots and special mobile robotic systems are resumed. Despite this, the robotic control systems mostly remained unchanged. Hence one can see all advantages and disadvantages of these systems. This is due to lack of funds, which could greatly facilitate the work of the operator, and in some cases, completely replace it. The paper is concerned with the complex machine vision of robotic system for monitoring of underground pipelines, which collects and analyzes up to 90% of the necessary information. Vision Systems are used to identify obstacles to the process of movement on a trajectory to determine their origin, dimensions and character. The object is illuminated in a structured light, TV camera records projected structure. Distortions of the structure uniquely determine the shape of the object in view of the camera. The reference illumination is synchronized with the camera. The main parameters of the system are the basic distance between the generator and the lights and the camera parallax angle (the angle between the optical axes of the projection unit and camera).

  6. Well servicing industry finds

    SciTech Connect

    Moore, S.D

    1989-07-01

    The U.S. well servicing industry showed modest growth last year, continuing a slow recovery that started in 1987. Even with crude oil prices up significantly during the first half of 1989, the year looks destined to be a repeat of 1988 slow but steady growth. According to this annual well servicing survey, U.S. operators spent $2.6 billion for well servicing in 1988 compared with $2.1 billion in 1987, a slight increase of 12%. Expenditures peaked in 1981 at more than $4 billion before bottoming out in 1986 at $1.65 billion. Most well servicing categories included in the PEI survey were down last year from 1987 levels, even though expenditures were up. This anomaly resulted from the service and supply companies' ability to increase prices for their products and services, even though the market for these products and services failed to expand noticeably. Total 1988 well servicing activities covered in this survey recompletions, lift and tubular repairs, remedial stimulation, and abandonment were off compared with 1987, dropping 10% from 415,000 to 372,000 jobs.

  7. The emerging medical/industrial complex. The industrialization of medicine.

    PubMed

    Maloney, F P

    1998-01-01

    Until recently, the traditional practice of medicine has been thought of as a cottage industry practiced by individuals or small partnership groups. The transition of practice settings to large groups, multi-specialty groups, and corporations has paved the way to industrialization, with even larger health care organizations primarily managed by non-physicians. The similarities of these events to the industrial revolution and its impact on crafts guilds are striking. In order to understand this point of view, this article explores the function and influence of crafts guilds during stages of industrial development and the dynamics of the changes of employment needs and employability in an industrial environment as a comparison to what is happening in the health care field.

  8. Everyday Life with ALS: A Practical Guide

    MedlinePlus

    ... course of ALS. ALS also will require some adaptations to your environment, both for safety and to ... the way, Chapter 6 will include information on adaptations for computer access. Though the chapter is called “ ...

  9. Effects of the Al content on pore structures of porous TieAl alloys

    SciTech Connect

    Jaing, Y; He, Y H; Xu, N P; Zou, J; Huang, B; Lui, C T

    2008-01-01

    Porous TieAl alloys with different nominal compositions were fabricated through a reactive synthesis of Ti and Al elemental powders. It has been found that the pore parameters vary with the Al contents, indicating that the nature of the pores can be manipulated through changing the Al contents. In addition, detailed structural characterizations showed that the fabricated porous TieAl alloys can have three crystalline phases (i.e., a2-Ti3Al, g-TiAl, and TiAl3) when using different compositions. The fundamental reasons behind these phenomena have been explored.

  10. Nonstoichiometry of Al-Zr intermetallic phases

    SciTech Connect

    Radmilovic, V.; Thomas, G.

    1994-06-01

    Nonstoichiometry of metastable cubic {beta}{prime} and equilibrium tetragonal {beta} Al-Zr intermetallic phases of the nominal composition Al{sub 3}Zr in Al-rich alloys has been extensively studied. It is proposed that the ``dark contrast`` of {beta}{prime} core in {beta}{prime}/{sigma}{prime} complex precipitates, in Al-Li-Zr based alloys, is caused by incorporation of Al and Li atoms into the {beta}{prime} phase on Zr sublattice sites, forming nonstoichiometric Al-Zr intermetallic phases, rather than by Li partitioning only. {beta}{prime} particles contain very small amounts of Zr, approximately 5 at.%, much less than the stoichiometric 25 at.% in the Al{sub 3}Zr metastable phase. These particles are, according to simulation of high resolution images, of the Al{sub 3}(Al{sub 0.4}Li{sub 0.4}Zr{sub 0.2}) type. Nonstoichiometric particles of average composition Al{sub 4}Zr and Al{sub 6}Zr are observed also in the binary Al-Zr alloy, even after annealing for several hours at 600{degree}C.

  11. Effects of lubrication on superplastic forming of 8090 Al-Li sheets

    SciTech Connect

    Chen, T.R.; Huang, J.C.; Liauo, J.M.; Hwang, Y.M. )

    1994-08-01

    The utilization of superplastic forming (SPF) for aluminum alloys in the aircraft industry has been a focus of study recently. In addition to the Al-Cu, Al-Mg, and Al-Zn-Mg base superplastic alloys, the Al-Li base system has attracted considerable attention. However, given the fact that the 8090 and 2090 Al-Li alloys exhibited uniaxial superplastic elongation in excess of 1,000%, the strain rate sensitivity at their optimum strain rate range is usually around 0.5[+-]0.2, compared with [approximately]0.75 seen in the 7575 Al alloys. the lower m-value in the Al-Li alloys might suggest a less uniform strain distribution during SPF, which will be of great concern in practice and is worth further careful studies. One of the improvement methods along this line is to use appropriate lubricants. The thickness distributions have been reported to be improved by the use of lubricants. Typical lubricants used for superplastic forming are graphite, boron nitride, molybdenum disulfide, etc. The rejection force needed for removing the formed specimen from the close-die can also be reduced significantly by using lubricants. The current study is to examine the forming behavior of the 8090 Al-Li alloy superplastically formed in a circular open (free bulging) or close die to variable levels of depth, with or without lubrication.

  12. Cenomanian-Turonian biostratigraphy of the Jardas Al Abid area, Al Jabal Al Akhdar, northeast Libya

    NASA Astrophysics Data System (ADS)

    El Qot, Gamal M.; Abdulsamad, Esam O.

    2016-09-01

    The Upper Cenomanian-Turonian succession exposed at Jardas al'Abid area consists mainly of carbonates with siliciclastic intercalations. This succession is subdivided lithostratigraphically into: Qasr al'Abid (Late Cenomanian) and Al Baniyah (Late Cenomanian-Coniacian) formations. This sequence is relatively rich in macrofossil assemblages especially bivalves, gastropods, and echinoids with rare ammonites. Based on the first occurrence (FO) and last occurrence (LO) of some index species of these macrofossil groups, an integrated biostratigraphic framework has been constructed. The studied Cenomanian-Turonian sequence is subdivided biostratigraphically into three ammonite biozones; Pseudaspidoceras pseudonodosoides Total Range Zone, Choffaticeras segne Total Range Zone, and Coilopoceras requienianum Total Range Zone. Based on the rest of macrofossil assemblages other than the ammonites, eight biozones were recognized; Mecaster batnensis Total Range Zone, Ceratostreon flabellatum-Neithea dutrugei Acme Zone, Costagyra olisiponensis Acme Zone, Pycnodonte (Phygraea) vesicularis vesiculosa Acme Zone, Mytiloides labiatus Total Range Zone = Mecaster turonensis Acme Zone, Rachiosoma rectilineatum-Curvostrea rouvillei-Tylostoma (T.) globosum Assemblage Zone, Radiolites sp.-Apricardia? matheroni Total Range Zone, and Nerinea requieniana Total Range Zone. Most of the proposed biozones are recorded for the first time from Libya. The integration among these biozones as well as local and inter-regional correlation of the biozones have been discussed. The stage boundaries of the studied stratigraphic intervals are discussed, where the Cenomanian/Turonian boundary is delineated at the last occurrence (LO) of Pseudaspidoceras pseudonodosoides (Choffat), while the Turonian/Coniacian boundary is delineated arbitrary being agree with the LO of the Turonian fauna.

  13. Biotechnology and the Food Industry.

    ERIC Educational Resources Information Center

    Henderson, Jenny; And Others

    1991-01-01

    Traditional and novel uses of enzymes and microbes in the baking, brewing, and dairy industries are described. Cheese, yogurt, baking, brewing, vinegar, soy sauce, single-cell proteins, enzymes, food modification, vanilla, citric acid, monosodium glutamate, xanthan gum, aspartame, and cochineal are discussed. Industrial links with firms involved…

  14. Japanese Industry Boosts Pollution Spending

    ERIC Educational Resources Information Center

    McAbee, Michael K.

    1975-01-01

    In response to tightening emission standards imposed by the government, Japanese industry will increase its capital spending on pollution control equipment to account for about 20 percent of all industrial capital spending. Preferential treatment and loans from government-affiliated financial institutions are available for projects. (Author/MLH)

  15. Manpower Impacts of Industrial Technology.

    ERIC Educational Resources Information Center

    New York State Dept. of Labor, Albany. Research and Statistics Office.

    The effects of technological change on the manpower and training needs of New York State industry were studied in a survey of 281 Industrial situations. The study was designed to help answer questions about the effects of factory and related technological change in displacing workers, in creating recruitment and training needs, and in altering the…

  16. Accreditation of Industrial Engineering Programs.

    ERIC Educational Resources Information Center

    Brooks, George H.

    The guidelines used in the accreditation of industrial engineering programs are discussed. Changes that have taken place in engineering curriculum are described, along with the philosophy of educators in formulating industrial engineering program requirements in the areas of faculty, facilities, curriculum, administration, and scholastic work.…

  17. Job Prospects for Industrial Engineers.

    ERIC Educational Resources Information Center

    Basta, Nicholas

    1986-01-01

    Because of the impetus on how to improve productivity in companies, the demand for graduating industrial engineers continues to be strong from a variety of sources. Starting salary offers for graduates have been averaging $26,784. Enrollments in industrial engineering programs are increasing (with 3,923 graduates in 1984). (JN)

  18. Industry-University Research Programs.

    ERIC Educational Resources Information Center

    Smith, Kenneth A.

    1984-01-01

    Points out advantages and disadvantages of industry-university research programs from industry and university viewpoints. Identifies conditions essential for long-term success of such arrangements. Also provides a case study of practices at the Massachusetts Institute of Technology (MIT), discussing policy guidelines and giving examples of joint…

  19. Road Transport Industry Training Board

    ERIC Educational Resources Information Center

    Industrial Training International, 1975

    1975-01-01

    The Road Transport Industry Training Board has recognized that manpower planning was the key to estimating the industry's training needs. The effective training methods discussed are: management training, Group Training Associations, apprentice training, direct training, and mobile-training service. (Author/BP)

  20. The Industrial Revolution: A Misnomer.

    ERIC Educational Resources Information Center

    Cameron, Rondo

    1982-01-01

    Argues that the British industrial revolution was in no sense inevitable and scarcely deserves the term "revolution." Examined are the characteristics which the British shared with other Europeans and ways in which they were distinctive that enabled them to become the first industrial nation. (RM)

  1. Automation; The New Industrial Revolution.

    ERIC Educational Resources Information Center

    Arnstein, George E.

    Automation is a word that describes the workings of computers and the innovations of automatic transfer machines in the factory. As the hallmark of the new industrial revolution, computers displace workers and create a need for new skills and retraining programs. With improved communication between industry and the educational community to…

  2. Instructional Design Parameters in Industry.

    ERIC Educational Resources Information Center

    Bleach, Kathleen M.

    The Restructuring Education in the Sciences for Industrial Alignment (RESIA) project examined the feasibility of combining college science faculty and industrial experts to produce instructional materials. These materials were intended for on-the-job training and college credit. Through informal contact, professors were identified who were willing…

  3. Ullmann's Encyclopedia of Industrial Chemistry.

    ERIC Educational Resources Information Center

    Chadwick, Sharon S.

    1988-01-01

    This review compares "Ullmann's Encyclopedia of Industrial Chemistry" with the "Kirk-Othmer Encyclopedia of Chemical Technology," two prominent encyclopedias of chemical technology and industry. Cost, quantity of information, organization, illustrations, authorship, abbreviations, online availability, and content of articles are discussed. (MES)

  4. Industry's Struggle for Skilled Workers.

    ERIC Educational Resources Information Center

    Barker, Don

    1979-01-01

    The growing shortage of skilled workers in industrial maintenance, the growing complexity of equipment, and the automation of production processes call for improved and increased employee training and retraining. A General Motors training supervisor notes how education and industry can cooperate to provide this education and training. (MF)

  5. Industry Invests in Research Centers.

    ERIC Educational Resources Information Center

    Ploch, Margie

    1983-01-01

    Universities and industry are forging new relationships to support academic research and industrial research and development, including the establishment of university/cooperative research centers. Discusses various cooperative projects at these research centers. Includes a list of representative R&D centers in biotechnology, building…

  6. Petroleum industry assists hurricane relief

    SciTech Connect

    Not Available

    1992-09-14

    This paper reports that the petroleum industry is aiding victims of last month's Hurricane Andrew with cash, clothing, food, water, and other supplies. Cash contributions announced as of last week totaled more than $2.7 million for distribution in South Florida and South Louisiana. Petroleum industry employees were collecting relief items such as bottled water and diapers for distribution in those areas.

  7. Cyclic oxidation resistance of a reaction milled NiAl-AlN composite

    NASA Technical Reports Server (NTRS)

    Lowell, Carl E.; Barrett, Charles A.; Whittenberger, J. D.

    1990-01-01

    Based upon recent mechanical property tests a NiAl-AlN composite produced by cryomilling has very attractive high temperature strength. This paper focuses on the oxidation resistance of the NiAl-AlN composite at 1473 and 1573 K as compared to that of Ni-47Al-0.15Zr, one of the most oxidation resistant intermetallics. The results of cyclic oxidation tests show that the NiAl-AlN composite has excellent properties although not quite as good as those of Ni-47Al-0.15Zr. The onset of failure of the NiAl-AlN was unique in that it was not accompanied by a change in scale composition from alumina to less protective oxides. Failure in the composite appears to be related to the entrapment of AlN particles within the alumina scale.

  8. Filtration in industrial hygiene.

    PubMed

    Brown, R C

    2001-01-01

    Filters used in industrial hygiene are of two basic types, corresponding with the two basic airborne hazards: particulate and vapor. They are as different in their construction as they are in their purpose, and each gives negligible protection against the other hazard. By use of the correct type, adequate filtration efficiency can usually be achieved. Most particulate filters are made from fibers, and finer fibers result in higher efficiency. Filters can capture particles much smaller than the fiber diameter, as a result of diffusional motion of the airborne particles and, in the case of filters that hold a permanent electric charge, electrostatic attraction. Most vapor filters are made from granules of activated carbon, which have an extremely large effective surface area, where molecules of contaminant are adsorbed. The performance of all filters tends to alter as the filter material becomes loaded. Electrically neutral particulate filters become more efficient but at the expense of increased resistance to airflow. Particulate filters that act by electric forces may become less efficient, and are often less inclined to clog. Vapor filters usually have a high initial efficiency, but the penetration of vapor increases as the filters become saturated with adsorbed vapor, and the performance of these filters is normally expressed in terms of their lifetime rather than their efficiency. It is important that the choice of a filter should be made with close reference to the situation in which it is to be used, and optimum respiratory protection should be sought, rather than maximum filtration efficiency. Special problems of filters are illustrated by some case histories, and finally the use of filters as size selectors for dust samplers is briefly described. PMID:11669390

  9. Dental Erosion in Industry

    PubMed Central

    Cate, H. J. Ten Bruggen

    1968-01-01

    Five hundred and fifty-five acid workers were examined between March 1962 and October 1964. One hundred and seventy-six (31·7%) were affected by industrial dental erosion at the first examinations. In 33 cases (6·0%) the dentine was affected. During the period of the survey, 66 (20·4%) of 324 workers examined more than once showed evidence that erosion was progressing. The prevalence and incidence of erosion were highest among battery formation workers, lower among picklers, and least among other processes covered by the survey. The age of workers did not appear to influence their susceptibility to erosion. The habit of working with the lips slightly parted had little effect. Erosion superimposed upon attrition predisposed to more severe loss of tooth structure than either operating alone. Little inconvenience or functional disability was suffered by acid workers due to erosion. Twenty-seven (23·7%) of 114 erosions were considered to be disfiguring. Regular dental treatment was sought less by acid workers than by controls, and the oral hygiene of the latter was superior. There was no evidence to show any difference between caries experience among acid workers and controls. Calculus and periodontal disease were more prevalent among acid workers than among controls, but it was not possible to attribute this to the working environment. Black staining in iron picklers was considered to be due to the working environment. The use of closed acid containers or lip extraction on open acid vats prevented significant atmospheric contamination and diminished the prevalence of erosion. The use of wall fans and detergent foaming agents was helpful. Images PMID:5723349

  10. AVLIS industrial access program

    SciTech Connect

    Not Available

    1984-11-15

    This document deals with the procurements planned for the construction of an Atomic Vapor Laser Isotope Separation (AVLIS) production plant. Several large-scale AVLIS facilities have already been built and tested; a full-scale engineering demonstration facility is currently under construction. The experience gained from these projects provides the procurement basis for the production plant construction and operation. In this document, the status of the AVLIS process procurement is presented from two viewpoints. The AVLIS Production Plant Work Breakdown Structure is referenced at the level of the items to be procured. The availability of suppliers for the items at this level is discussed. In addition, the work that will result from the AVLIS enrichment plant project is broken down by general procurement categories (construction, mechanical equipment, etc.) and the current AVLIS suppliers are listed according to these categories. A large number of companies in all categories are currently providing AVLIS equipment for the Full-Scale Demonstration Facility in Livermore, California. These companies form an existing and expanding supplier network for the AVLIS program. Finally, this document examines the relationship between the AVLIS construction project/operational facility and established commercial suppliers. The goal is to utilize existing industrial capability to meet the needs of the project in a competitive procurement situation. As a result, costs and procurement risks are both reduced because the products provided come from within the AVLIS suppliers' experience base. At the same time, suppliers can benefit by the potential to participate in AVLIS technology spin-off markets. 35 figures.

  11. Uranium industry annual 1993

    SciTech Connect

    Not Available

    1994-09-01

    Uranium production in the United States has declined dramatically from a peak of 43.7 million pounds U{sub 3}O{sub 8} (16.8 thousand metric tons uranium (U)) in 1980 to 3.1 million pounds U{sub 3}O{sub 8} (1.2 thousand metric tons U) in 1993. This decline is attributed to the world uranium market experiencing oversupply and intense competition. Large inventories of uranium accumulated when optimistic forecasts for growth in nuclear power generation were not realized. The other factor which is affecting U.S. uranium production is that some other countries, notably Australia and Canada, possess higher quality uranium reserves that can be mined at lower costs than those of the United States. Realizing its competitive advantage, Canada was the world`s largest producer in 1993 with an output of 23.9 million pounds U{sub 3}O{sub 8} (9.2 thousand metric tons U). The U.S. uranium industry, responding to over a decade of declining market prices, has downsized and adopted less costly and more efficient production methods. The main result has been a suspension of production from conventional mines and mills. Since mid-1992, only nonconventional production facilities, chiefly in situ leach (ISL) mining and byproduct recovery, have operated in the United States. In contrast, nonconventional sources provided only 13 percent of the uranium produced in 1980. ISL mining has developed into the most cost efficient and environmentally acceptable method for producing uranium in the United States. The process, also known as solution mining, differs from conventional mining in that solutions are used to recover uranium from the ground without excavating the ore and generating associated solid waste. This article describes the current ISL Yang technology and its regulatory approval process, and provides an analysis of the factors favoring ISL mining over conventional methods in a declining uranium market.

  12. The advanced light source: America`s brightest light for science and industry

    SciTech Connect

    Cross, J.; Lawler, G.

    1994-03-01

    America`s brightest light comes from the Advanced Light Source (ALS), a national facility for scientific research, product development, and manufacturing. Completed in 1993, the ALS produces light in the ultraviolet and x-ray regions of the spectrum. Its extreme brightness provides opportunities for scientific and technical progress not possible anywhere else. Technology is poised on the brink of a major revolution - one in which vital machine components and industrial processes will be drastically miniaturized. Industrialized nations are vying for leadership in this revolution - and the huge economic rewards the leaders will reap.

  13. Wear behavior of Al-Al{sub 3}Ti composite manufactured by a centrifugal method

    SciTech Connect

    Watanabe, Yoshimi; Yamanaka, Noboru; Fukui, Yasuyoshi

    1999-12-01

    The purpose of the present study was to develop a wear-resistant, light Al-Al{sub 3}Ti composite material. An Al-Al{sub 3}Ti composite specimen was machined from a thick-walled tube of Al-Al{sub 3}Ti functionally graded material (FGM) manufactured by the centrifugal method from a commercial ingot of Al-5 mass% Ti master alloy. The alloy was heated to a temperature where solid Al{sub 3}Ti particles resided in a liquid Al matrix, and then the centrifugal method was carried out. Al{sub 3}Ti particles in a commercial alloy ingot exist as platelets, and this shape was maintained through the casting. Three kinds of wear specimens were prepared, taking into account the morphology of the Al{sub 3}Ti particles in the thick-walled FGM tube; the Al{sub 3}Ti particles were arranged with their platelet planes nearly normal to the radial direction as a result of the applied centrifugal force. The wear resistance of the Al-Al{sub 3}Ti composite was significantly higher than that of pure Al. Wear-resistance anisotropy and dissolution of the Al{sub 3}Ti into the Al matrix at the near-surface region, around 100 {micro}m in depth, were also observed. The mechanism of the supersaturated-layer formation and the origin of the anisotropic wear resistance are discussed.

  14. Industrial ecology: concepts and approaches.

    PubMed Central

    Jelinski, L W; Graedel, T E; Laudise, R A; McCall, D W; Patel, C K

    1992-01-01

    Industrial ecology is a new approach to the industrial design of products and processes and the implementation of sustainable manufacturing strategies. It is a concept in which an industrial system is viewed not in isolation from its surrounding systems but in concert with them. Industrial ecology seeks to optimize the total materials cycle from virgin material to finished material, to component, to product, to waste product, and to ultimate disposal. To better characterize the topic, the National Academy of Sciences convened a colloquium from which were derived a number of salient contributions. This paper sets the stage for the contributions that follow and discusses how each fits into the framework of industrial ecology. PMID:11607253

  15. Nanocoatings for High-Efficiency Industrial Hydraulic and Tooling Systems

    SciTech Connect

    Clifton B. Higdon III

    2011-01-07

    Industrial manufacturing in the U.S. accounts for roughly one third of the 98 quadrillion Btu total energy consumption. Motor system losses amount to 1.3 quadrillion Btu, which represents the largest proportional loss of any end-use category, while pumps alone represent over 574 trillion BTU (TBTU) of energy loss each year. The efficiency of machines with moving components is a function of the amount of energy lost to heat because of friction between contacting surfaces. The friction between these interfaces also contributes to downtime and the loss of productivity through component wear and subsequent repair. The production of new replacement parts requires additional energy. Among efforts to reduce energy losses, wear-resistant, low-friction coatings on rotating and sliding components offer a promising approach that is fully compatible with existing equipment and processes. In addition to lubrication, one of the most desirable solutions is to apply a protective coating or surface treatment to rotating or sliding components to reduce their friction coefficients, thereby leading to reduced wear. Historically, a number of materials such as diamond-like carbon (DLC), titanium nitride (TiN), titanium aluminum nitride (TiAlN), and tungsten carbide (WC) have been examined as tribological coatings. The primary objective of this project was the development of a variety of thin film nanocoatings, derived from the AlMgB14 system, with a focus on reducing wear and friction in both industrial hydraulics and cutting tool applications. Proof-of-concept studies leading up to this project had shown that the constituent phases, AlMgB14 and TiB2, were capable of producing low-friction coatings by pulsed laser deposition. These coatings combine high hardness with a low friction coefficient, and were shown to substantially reduce wear in laboratory tribology tests. Selection of the two applications was based largely on the concept of improved mechanical interface efficiencies for

  16. Systems Engineering Techniques for ALS Decision Making

    NASA Technical Reports Server (NTRS)

    Rodriquez, Luis F.; Drysdale, Alan E.; Jones, Harry; Levri, Julie A.

    2004-01-01

    The Advanced Life Support (ALS) Metric is the predominant tool for predicting the cost of ALS systems. Metric goals for the ALS Program are daunting, requiring a threefold increase in the ALS Metric by 2010. Confounding the problem, the rate new ALS technologies reach the maturity required for consideration in the ALS Metric and the rate at which new configurations are developed is slow, limiting the search space and potentially giving the perspective of a ALS technology, the ALS Metric may remain elusive. This paper is a sequel to a paper published in the proceedings of the 2003 ICES conference entitled, "Managing to the metric: an approach to optimizing life support costs." The conclusions of that paper state that the largest contributors to the ALS Metric should be targeted by ALS researchers and management for maximum metric reductions. Certainly, these areas potentially offer large potential benefits to future ALS missions; however, the ALS Metric is not the only decision-making tool available to the community. To facilitate decision-making within the ALS community a combination of metrics should be utilized, such as the Equivalent System Mass (ESM)-based ALS metric, but also those available through techniques such as life cycle costing and faithful consideration of the sensitivity of the assumed models and data. Often a lack of data is cited as the reason why these techniques are not considered for utilization. An existing database development effort within the ALS community, known as OPIS, may provide the opportunity to collect the necessary information to enable the proposed systems analyses. A review of these additional analysis techniques is provided, focusing on the data necessary to enable these. The discussion is concluded by proposing how the data may be utilized by analysts in the future.

  17. A case-only study of interactions between metabolic enzyme polymorphisms and industrial pollution in childhood acute leukemia.

    PubMed

    Yang, You; Tian, Ying; Jin, Xingming; Yan, Chonghuai; Jiang, Fan; Zhang, Yiwen; Tang, Jingyan; Shen, Xiaoming

    2009-09-01

    Cancer risk is modulated by gene-environment interactions between toxic exposure and genetic variation in carcinogen metabolism. Our objective was to assess interactions between exposure to industrial pollutants and polymorphisms affecting cytochrome P450s (CYP1A1 and CYP2E1) and glutathione S-transferases (GSTP1 and GSTT) in childhood acute leukemia (AL). A case-only design was conducted in 123 Chinese children with sporadic AL. Industrial plants in the vicinity were recorded and, if present, their size and proximity to the usual place of residence of AL children was evaluated. Unconditional logistic regression analysis was performed across the AL study group adjusting for age, gender, parental education, occupation and smoking, indoor and outdoor pesticide use, presence of television sets, refrigerators, microwave ovens and furniture material in children's rooms, and electric transformers, power lines, and telecommunication transmitters within 500 m. This analysis revealed an interaction between the GSTT null allele and industrial plants within 500 m of the residences of childhood AL patients (interaction odds ratio, COR=2.96, 95% CI: 1.09-8.01). Furthermore, the COR for the interaction between GSTT null and industrial plants within 50 m was 5.99 (95% CI: 1.41-25.45). Our results suggest an association between proximity to industrial plants and the GSTT null allele in patients with childhood AL.

  18. Preliminary Results of National Amyotrophic Lateral Sclerosis (ALS) Registry Risk Factor Survey Data

    PubMed Central

    2016-01-01

    Background The National ALS Registry is made up of two components to capture amyotrophic lateral sclerosis (ALS) cases: national administrative databases (Medicare, Medicaid, Veterans Health Administration and Veterans Benefits Administration) and self-identified cases captured by the Registry’s web portal. This study describes self-reported characteristics of U.S. adults with ALS using the data collected by the National ALS Registry web portal risk factor surveys only from October 19, 2010 through December 31, 2013. Objective To describe findings from the National ALS Registry’s web portal risk factor surveys. Measurements The prevalence of select risk factors among adults with ALS was determined by calculating the frequencies of select risk factors—smoking and alcohol (non, current and former) histories, military service and occupational history, and family history of neurodegenerative diseases such as ALS, Alzheimer’s and/or Parkinson’s. Results Nearly half of survey respondents were ever smokers compared with nearly 41% of adults nationally. Most respondents were ever drinkers which is comparable to national estimates. The majority were light drinkers. Nearly one-quarter of survey respondents were veterans compared with roughly 9% of US adults nationally. Most respondents were retired or disabled. The industries in which respondents were employed for the longest time were Professional and Scientific and Technical Services. When family history of neurodegenerative diseases in first degree relatives was evaluated against our comparison group, the rates of ALS were similar, but were higher for Parkinson’s disease, Alzheimer’s disease and any neurodegenerative diseases. Conclusions The National ALS Registry web portal, to our knowledge, is the largest, most geographically diverse collection of risk factor data about adults living with ALS. Various characteristics were consistent with other published studies on ALS risk factors and will allow

  19. Wettability of AlSi5Mg on Spodumene

    NASA Astrophysics Data System (ADS)

    Fankhänel, Beate; Stelter, Michael; Voigt, Claudia; Aneziris, Christos G.

    2015-02-01

    The development of new filters for the aluminum industry requires investigations on the wettability of aluminum and its alloys on novel filter materials. The requested filter effects require not only an adequate wetting but also information about the interaction between the filter material and the metal. In the present work the wettability of an AlSi5Mg alloy on spodumene (LiAl[Si2O6]) containing substrates is investigated using the sessile drop technique. These measurements were carried out at 1223 K (950 °C) under vacuum. The spodumene-based substrates showed a completely different wetting behavior compared with an alumina substrate. The contact angel reduced more quickly and leveled out at a lower value (75 ± 2 deg) than in case of a pure alumina substrate (90 ± 1 deg). The reason for this behavior is a reaction between the LiAl(Si2O6) and the alloy droplet which supported deoxidation and formed a silica-rich reaction layer at the droplet/substrate interface.

  20. Industrial Assessment Center Program

    SciTech Connect

    Kolarik, William J.

    2007-02-26

    Over the five-year period (2002-2006) the Oklahoma State University Industrial Assessment Center (IAC) performed energy assessments for 106 different clients, writing 835 recommendations, for a total of $23,937,099 in potential estimated annual savings. IAC clients served consisted of small and medium-sized manufacturers ranging from food manufactures to foundries. The OSU IAC served clients in Oklahoma, Kansas, Missouri, Arkansas, and Texas. In addition to client service, student training and instruction was a major accomplishment. The OSU IAC employed (and trained) 12 baccalaureate-level students, 17 masters-level graduate students, and 7 doctoral-level graduate students. Most are practicing in the energy management area. Training was focused on both energy assessment and safety. Safety training was both center-based training as well as on-site training. Energy management related training was focused on classroom (for academic credit) work at both the undergraduate and graduate level. IEM 4923 (Energy and Water Management) was developed to serve both the IAC as well as non-IAC students. It was delivered once per year, with enrollments of typically 10 to 20 students. This course was required for IAC student employees, both undergraduate and graduate. This course was patterned after the AEE CEM (five-day) course for practicing professionals. IEM 4923 required each student to attend at least one on-site assessment and write at least one recommendation for their client’s report. Hence, a hands-on approach was practiced. Advance level courses were used to train graduate students. Two courses played major roles here: IEM 5923 (Advanced Energy and Water Management) and IEM 5943 (Hazardous Material and Waste). Graduate student participation in these courses helped the IAC to gain additional perspectives in on-site assessment and resulting recommendations. Numerous hands-on demonstration/training was conducted by directors and graduate students in order to gain

  1. Structure and stability of the AlX and AlX{sup {minus}} species

    SciTech Connect

    Gutsev, G.L.; Jena, P.; Bartlett, R.J.

    1999-02-01

    The electronic and geometrical structures of the ground and low-lying excited states of the diatomic AlX and AlX{sup {minus}} series (X=H, Li, Be, B, C, N, O, and F) are calculated by the coupled-cluster method with all singles and doubles and noniterative inclusion of triples using a large atomic natural orbital basis. All the ground-state AlX molecules except for AlF can attach an additional electron and form ground-state AlX{sup {minus}} anions. The ground-state AlBe{sup {minus}}, AlB{sup {minus}}, AlC{sup {minus}}, AlN{sup {minus}}, and AlO{sup {minus}} anions possess excited states that are stable toward autodetachment of an extra electron; AlBe{sup {minus}} also has a second excited state. Low-lying excited states of all AlX but AlN can attach an extra electron and form anionic states that are stable with respect to their neutral (excited) parent states. The ground-state AlLi{sup {minus}}, AlBe{sup {minus}}, AlB{sup {minus}}, AlN{sup {minus}}, and AlO{sup {minus}} anions are found to be thermodynamically more stable than their neutral parents. The most stable is AlO{sup {minus}}, whose dissociation energy to Al+O{sup {minus}} is 6.4 eV. Correspondingly, AlO possesses the largest electron affinity (2.65 eV) in the series. {copyright} {ital 1999 American Institute of Physics.}

  2. Accumulation of Al in Root Mucilage of an Al-Resistant and an Al-Sensitive Cultivar of Wheat.

    PubMed Central

    Archambault, D. J.; Zhang, G.; Taylor, G. J.

    1996-01-01

    To estimate rates of Al accumulation within the symplasm, all apoplastic pools of Al need to be eliminated or accounted for. We have developed a revised kinetic protocol that allows us to estimate the contribution of mucilage-bound Al to total, nonexchangeable Al, and to eliminate the mucilage as an apoplastic pool of Al. By comparing the Al content of excised root tips (2 cm) of wheat (Triticum aestivum L.) with and without the removal of the mucilage (using a 10-min wash in 1 M NH4Cl), we found that Al bound to the mucilage accounted for approximately 25 to 35% of Al remaining after desorption in citric acid. The kinetics of Al uptake into mucilage were biphasic, with a rapid phase occurring in the first 30 min of uptake, followed by a linear phase occurring in the remainder of the experimental period (180 min). By adopting a step for removal of mucilage into our existing kinetic protocol, we have been able to isolate a linear phase of uptake with only a slight deviation from linearity in the first 5 min. Although we cannot unambiguously identify this phase of uptake as uptake into the symplasm, we believe this new protocol provides us with the most accurate quantitative estimate of symplastic Al yet available. PMID:12226458

  3. Magnetism of Al-substituted magnetite reduced from Al-hematite

    NASA Astrophysics Data System (ADS)

    Jiang, Zhaoxia; Liu, Qingsong; Zhao, Xiang; Roberts, Andrew P.; Heslop, David; Barrón, Vidal; Torrent, José

    2016-06-01

    Aluminum-substituted magnetite (Al-magnetite) reduced from Al-substituted hematite or goethite (Al-hematite or Al-goethite) is an environmentally important constituent of magnetically enhanced soils. In order to characterize the magnetic properties of Al-magnetite, two series of Al-magnetite samples were synthesized through reduction of Al-hematite by a mixed gas (80% CO2 and 20% CO) at 395°C for 72 h in a quartz tube furnace. Al-magnetite samples inherited the morphology of their parent Al-hematite samples, but only those transformed from Al-hematite synthesized at low temperature possessed surficial micropores, which originated from the release of structural water during heating. Surface micropores could thus serve as a practical fingerprint of fire or other high-temperature mineralogical alteration processes in natural environments, e.g., shear friction in seismic zones. In addition, Al substitution greatly affects the magnetic properties of Al-magnetite. For example, coercivity (Bc) increases with increasing Al content and then decreases slightly, while the saturation magnetization (Ms), Curie temperature (Tc), and Verwey transition temperature (Tv) all decrease with increasing Al content due to crystal defect formation and dilution of magnetic ions caused by Al incorporation. Moreover, different trends in the correlation between Tc and Bc can be used to discriminate titanomagnetite from Al-magnetite, which is likely to be important in environmental and paleomagnetic studies, particularly in soil.

  4. Reactive Plasma Spraying of Fine Al2O3/AlN Feedstock Powder

    NASA Astrophysics Data System (ADS)

    Shahien, Mohammed; Yamada, Motohiro; Yasui, Toshiaki; Fukumoto, Masahiro

    2013-12-01

    Reactive plasma spraying (RPS) is a promising technology for in situ formation of aluminum nitride (AlN) coatings. Recently, AlN-based coatings were fabricated by RPS of alumina (Al2O3) powder in N2/H2 thermal plasma. This study investigated the feasibility of RPS of a fine Al2O3/AlN mixture and the influence of the plasma gases (N2, H2) on the nitriding conversion, and coating microstructure and properties. Thick AlN/Al2O3 coatings with high nitride content were successfully fabricated. The coatings consist of h-AlN, c-AlN, Al5O6N, γ-Al2O3, and a small amount of α-Al2O3. Use of fine particles enhanced the nitriding conversion and the melting tendency by increasing the surface area. Furthermore, the AlN additive improved the AlN content in the coatings. Increasing the N2 gas flow rate improved the nitride content and complete crystal growth to the h-AlN phase, and enhanced the coating thickness. On the other hand, though the H2 gas is required for plasma nitriding of the Al2O3 particles, increasing its flow rate decreased the nitride content and the coating thickness. Remarkable influence of the plasma gases on the coating composition, microstructure, and properties was observed during RPS of the fine particles.

  5. 77 FR 73732 - In the Matter of Amendment of the Designation of al-Qa'ida in Iraq, aka Jam'at al Tawhid wa'al...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-12-11

    ... al-Rafidayn, aka The Organization of al-Jihad's Base of Operations in Iraq, aka al-Qaida of Jihad in Iraq, aka al-Qaida in Iraq, aka al-Qaida in Mesopotamia, aka al-Qaida in the Land of the Two Rivers, aka al-Qaida of the Jihad in the Land of the Two Rivers, aka al-Qaida of Jihad Organization in......

  6. Causes for Retail Industry Globalization

    NASA Astrophysics Data System (ADS)

    Jagadeesha, M.

    2012-12-01

    The heading of this article itself pushing me to think why retail industry is globalizing! Because to increase their presence worldwide and profit on the onside and for the sake of ìname and fameî in industry is other side, but todayís trend and compitetitation force industrial giants to forget the word ìname and fameî globalization is the only strategy to compensate their market share or profit from one country to another country or domestic market. The presence of retail industry in the global level from centuries, but the global recognaization of retail industry came to limelight only two decades ago. As soon as restrictions are removed in this sector, all the retail industry big giants spread across the world to extend their operations especially in emerging markets. Is this a good sign for retailers? Off course it is good sign for some countries and some countries are stick to their own perceptions. Some of the countries welcome this move because the FDI will improve their economic structure. On the other side employment opportunity is also one of the issues in globalization of retail sector. Because retail industry needs huge workforce, so significance of retail has been undoubted.

  7. How utilizes can revitalize industry

    SciTech Connect

    De Vaul, D.; Bartsch, C.

    1993-12-31

    During the first weeks of his presidency, Bill Clinton asserted that the nation`s industries must modernize if Americans are to enjoy a rising standard of living. He noted that inadequate knowledge about new production technologies and inadequate capital for plant improvements were making it hard for manufacturers, particularly small and midsized firms, to improve their productivity and economic competitiveness. And though he said his administration would stress the benefits of government research, technology transfer, and financial assistance, President Clinton acknowledged that Washington needs new partners to help modernize U.S. industrial processes. Electric utilities are likely candidates. They have considerable technical expertise and access to large sums of capital that could help industry improve its productivity. Fortuitously, power companies also would benefit by such a partnership stimulating local economic activity and better managing electricity demands. Although many utilities pursue so-called demand-side management programs for their commercial and residential customers, most have not focused much attention on the industrial sector, in part because achieving industrial energy efficiency requires more specialized expertise than do routine energy audits to improve the insulation and lighting of homes and commercial buildings. Yet the reasons to target industry are compelling: Industrial firms consume more than 35 percent of the electricity in the United States, and investment in retooling manufacturing operations with energy-efficient and productive equipment could help spur economic revitalization.

  8. Forging strategic partnerships with industry: The Industrial Fellows Program

    SciTech Connect

    Adams, K.; Castain, R.; Hynes, M.V.; Sanders, V.; Siemon, R.; Tellier, A.; Tiedman, A.; Umbarger, J.; Wilson, M.

    1995-04-01

    Science, technology, and industrial policy are at an important nexus due to long developing trends in the national and international economy and recent events in national security affairs. The research and development assets built by the American taxpayer in response to the Cold War face a quest for relevance in the new era. National competitiveness in international markets has emerged as an important new priority. To better understand the perspective of US industry the management of the Los Alamos National Laboratory has initiated an Industrial Fellows Program which has placed six individuals at US corporations. Their goal is to create strategic partnerships through increased understanding of technical needs of industry and the technical capabilities of the Laboratory.

  9. The U.S. Chemical Industry, Foreign Chemical Industries

    ERIC Educational Resources Information Center

    Chemical and Engineering News, 1972

    1972-01-01

    This section of the annual report on the chemical industry provides data on the chemical production of Japan, West Germany, United Kingdom, Italy, and France, including the output of major chemical products in these nations. (PR)

  10. Technical change in US industry: A cross-industry analysis

    NASA Technical Reports Server (NTRS)

    Nelson, R. R. (Editor)

    1981-01-01

    The nature of the public policies which have influenced the pace and pattern of technical progress in a number of American industries is studied with the view of assessing the broad effects of these policies. The industries studied are agriculture, pharmaceuticals, semiconductors, computers, civil aircraft, automobiles and residential construction. The policies considered include research and development funding as well as government procurement, education, information dissemination, patent protection, licensing, regulations, and anti-trust policies.

  11. The Kinetics of TiAl3 Formation in Explosively Welded Ti-Al Multilayers During Heat Treatment

    NASA Astrophysics Data System (ADS)

    Foadian, Farzad; Soltanieh, Mansour; Adeli, Mandana; Etminanbakhsh, Majid

    2016-06-01

    Metallic-intermetallic laminate (MIL) composites, including Ti/TiAl3 composite, are promising materials for many applications, namely, in the aerospace industry. One method to produce Ti/TiAl3 laminate composite is to provide close attachment between desired number of titanium and aluminum plates, so that by applying heat and/or pressure, the formation of intermetallic phases between the layers becomes possible. In this work, explosive welding was used to make a strong bond between six alternative Ti and Al layers. The welded samples were annealed at three different temperatures: 903 K, 873 K, and 843 K (630 °C, 600 °C, and 570 °C) in ambient atmosphere, and the variation of the intermetallic layer thickness was used to study the growth kinetics. Microstructural investigations were carried out on the welded and annealed samples using optical microscopy and scanning electron microscopy equipped with energy-dispersive X-ray spectrometer (EDS). X-ray diffraction (XRD) technique was used to identify the formed intermetallic phases. It was found that at each temperature, two different mechanisms govern the process: reaction controlled and diffusion controlled. The calculated values of activation energies for reaction-controlled and diffusion-controlled mechanisms are 232.1 and 17.4 kJ, respectively.

  12. The Kinetics of TiAl3 Formation in Explosively Welded Ti-Al Multilayers During Heat Treatment

    NASA Astrophysics Data System (ADS)

    Foadian, Farzad; Soltanieh, Mansour; Adeli, Mandana; Etminanbakhsh, Majid

    2016-10-01

    Metallic-intermetallic laminate (MIL) composites, including Ti/TiAl3 composite, are promising materials for many applications, namely, in the aerospace industry. One method to produce Ti/TiAl3 laminate composite is to provide close attachment between desired number of titanium and aluminum plates, so that by applying heat and/or pressure, the formation of intermetallic phases between the layers becomes possible. In this work, explosive welding was used to make a strong bond between six alternative Ti and Al layers. The welded samples were annealed at three different temperatures: 903 K, 873 K, and 843 K (630 °C, 600 °C, and 570 °C) in ambient atmosphere, and the variation of the intermetallic layer thickness was used to study the growth kinetics. Microstructural investigations were carried out on the welded and annealed samples using optical microscopy and scanning electron microscopy equipped with energy-dispersive X-ray spectrometer (EDS). X-ray diffraction (XRD) technique was used to identify the formed intermetallic phases. It was found that at each temperature, two different mechanisms govern the process: reaction controlled and diffusion controlled. The calculated values of activation energies for reaction-controlled and diffusion-controlled mechanisms are 232.1 and 17.4 kJ, respectively.

  13. Knowledge industry: a powerful mechanism.

    PubMed

    Miguelote, Vera Regina da Silva; Camargo Jr, Kenneth Rochel de

    2010-02-01

    The paper deals with the pharmaceutical industry's links to the knowledge industry, through powerful marketing strategies. With the aim of scientifically legitimizing its products, the pharmaceutical industry interferes with the production of medical knowledge. In the form of a mechanism for directing economic interests, it funds drug research, biases its results and stimulates the production and publication of scientific papers. This is a mechanism that threatens important ethical issues: it transforms the process of scientific legitimization into a marketing strategy, compromises the credibility of the process of constructing medical knowledge and encourages distortions of the criteria for evaluating the quality of scientific papers. PMID:20140344

  14. Mining Industry Energy Bandwidth Study

    SciTech Connect

    none,

    2007-07-01

    The Industrial Technologies Program (ITP) relies on analytical studies to identify large energy reduction opportunities in energy-intensive industries and uses these results to guide its R&D portfolio. The energy bandwidth illustrates the total energy-saving opportunity that exists in the industry if the current processes are improved by implementing more energy-efficient practices and by using advanced technologies. This bandwidth analysis report was conducted to assist the ITP Mining R&D program in identifying energy-saving opportunities in coal, metals, and mineral mining. These opportunities were analyzed in key mining processes of blasting, dewatering, drilling, digging, ventilation, materials handling, crushing, grinding, and separations.

  15. Economic considerations in space industrialization

    NASA Technical Reports Server (NTRS)

    Ayres, R. U.; Ayres, L. W.; Criswell, D. R.

    1979-01-01

    The industrial categories of the United States economy are surveyed to identify those which can function using dominantly lunar raw materials or lunar derived feedstocks (LDF) and solar energy. Sixty-four standard industrial categories (SIC) appear to be compatible with LDF inputs; another 166 SIC's might be adaptable to LDF and space industry if substitution of materials and/or terrestrial supplements were introduced. Analytic tools are presented to use in deciding optimal strategies by which a generalized economy can be developed in space in an optimal manner within given constraints of capital, products derived at a given time, local production costs, cost of import from earth and other factors.

  16. Financing the Air Transportation Industry

    NASA Technical Reports Server (NTRS)

    Lloyd-Jones, D. J.

    1972-01-01

    The basic characteristics of the air transportation industry are outlined and it is shown how they affect financing requirements and patterns of production. The choice of financial timing is imperative in order to get the best interest rates available and to insure a fair return to investors. The fact that the industry cannot store its products has a fairly major effect on the amount of equipment to purchase, the amount of capital investment required, and the amount of return required to offset industry depriciation.

  17. Industrial processes influenced by gravity

    NASA Technical Reports Server (NTRS)

    Ostrach, Simon

    1988-01-01

    In considering new directions for low gravity research with particular regard to broadening the number and types of industrial involvements, it is noted that transport phenomena play a vital role in diverse processes in the chemical, pharmaceutical, food, and biotech industries. Relatively little attention has been given to the role of gravity in such processes. Accordingly, numerous industrial processes and phenomena are identified which involve gravity and/or surface tension forces. Phase separations and mixing are examples that will be significantly different in low gravity conditions. A basis is presented for expanding the scope of the low gravity research program and the potential benefits of such research is indicated.

  18. Agricultural and industrial process heat

    NASA Technical Reports Server (NTRS)

    Dollard, J.

    1978-01-01

    The application of solar energy to agricultural and industrial process heat requirements is discussed. This energy end use sector has been the largest and it appears that solar energy can, when fully developed and commercialized, displace from three to eight or more quads of oil and natural gas in U.S. industry. This potential for fossil fuel displacement in the agricultural and industrial process heat area sector represents a possible savings of 1.4 to 3.8 million barrels of oil daily.

  19. [Development, health-industrial complex and industrial policy].

    PubMed

    Gadelha, Carlos Augusto Grabois

    2006-08-01

    This paper puts health questions within the context of national development and industrial policy. It follows the idea of structuralist, Marxist and Schumpeterian approaches, in which industry and innovations form determining factors for the dynamism in capitalist economies and relative positions within the world economy. All countries that have developed and started to compete under better conditions with advanced countries have had an association between strong industry and an endogenous knowledge, learning and innovation base. However, in the field of health, this vision presents problems because business interests move according to the economic logic of profit rather than to meet health needs. The notion of the health-industrial complex is an attempt to provide a theoretical reference that enables linkage between two distinct types of logic: health and economic development. This study has sought to show, on the basis of foreign trade data, how disregard for the logic of health policy development has led to a situation of economic vulnerability in this sector, which may limit the objectives of universality, equality and comprehensiveness. Within this context, a cognitive and political break with these antagonistic visions that put health needs on one side and industrial needs on the other is proposed. A country that aims to reach a condition of development and independence requires strong innovative industries and an inclusive and universal health system, at the same time. PMID:16924298

  20. Photoluminescence properties of AlN-doped BaMgAl{sub 10}O{sub 17}:Eu{sup 2+} phosphors

    SciTech Connect

    Wang, Yong; Tang, Jianfeng; Ouyang, Xicheng; Liu, Buqiong; Lin, Rong Han

    2013-06-01

    Highlights: ► Ideal hexagonal shape particle size in 5 μm and 2.5–3 μm in thickness are obtained. ► The growth mechanism is studied by a computer simulation. ► The influence of introduced AlN on the sites of Eu{sup 2+} and photoluminescence properties was investigated. - Abstract: The AlN-doped BaMgAl{sub 10}O{sub 17}:Eu{sup 2+} phosphors were synthesized by conventional solid-state reaction. Powder X-ray diffraction (XRD), scanning electron microscope (SEM) and photoluminescence spectrum (PL) were used for characterization. The growth mechanism was carried out by computer simulation with CASTEP application, and revealed that an ideal hexagonal shape, particle size in 5 μm and 2.5–3 μm in thickness, could be obtained by AlN doping. Additionally, due to the low electronegativity of N{sup 3−}, the AlN-doped sample showed 35% increase in PL intensity and improvement of thermal stability. These fine particle size and better photoluminescence properties are expected to be applicable to industrial production of BaMgAl{sub 10}O{sub 17}:Eu{sup 2+} phosphors.

  1. A comparison of mechanical properties between Al and Al3Mg

    NASA Astrophysics Data System (ADS)

    Yang, Rong; Tang, Bin; Gao, Tao

    2016-11-01

    On the basis of first principles calculations, we have calculated the elastic properties, stress-strain relations, ideal tensile strengths, ideal shear strengths, and the ideal compressed strengths of Al and Al3Mg. The stress-strain relations of Al3Mg are strikingly similar to those of Al, indicating that the crystal structure appears to be more important than the identity of the individual atoms during uniaxial deformation. Al3Mg is found to have larger moduli and higher strengths than Al but less ductile than Al. So Al3Mg is expected to be a harder material, consistent with its exploitation in Al precipitate-hardening mechanisms. The calculated elastic properties, tensile strengths and shear strengths of Al are consistent with experimental values or previous theoretical results. We also use another method (molecular dynamics (MD) simulations) to recalculate elastic constants, ideal tensile and compressed strength of Al3Mg for checking and comparing. We find that the results obtained by the two methods agree well with each other. The failure modes under uniaxial <100> tension are also explored for Al and Al3Mg. Our calculations confirm that Al fail by shear and predict that Al3Mg also fail by shear.

  2. Influences of Al particles on the microstructure and property of electrodeposited Ni-Al composite coatings

    NASA Astrophysics Data System (ADS)

    Cai, Fei; Jiang, Chuanhai

    2014-02-01

    Ni-Al composite coatings with different contents of Al microparticles were prepared from a conventional Watt bath. The influences of Al particle loadings in the bath on the surface morphology, composition, texture, grain size, microstrain, residual stress and anti-corrosion of the Ni-Al composite coating were investigated. The friction coefficients of the coatings at 200 °C were also evaluated by a pin-on-disctribometer. The results showed that the surface morphology of the coatings changed from pyramid + colonied structure to colonied structure with increasing Al particle loadings. The (2 0 0) preferred orientation for pure Ni coating evolved to random orientation with increasing Al particle loadings. The grain size obtained the minimum value of 72.28 nm at Al particle loading of 100 g/L and the microstrain of the coating increased with increasing the Al particle loadings. The incorporation of Al particles decreased the residual stress of the electro-deposited coating and all the coatings deposited at different Al particle loadings possessed low residual stress. As the Al particle loading increased, the anti-corrosion of the Ni-Al coatings increased owing to the combined effect of increasing Al content in the coatings and the texture evolution from (2 0 0) plane to (1 1 1) plane. The wear result suggested that the increasing Al particle content did not improve the wear performance of the Ni-Al composite coatings.

  3. 29 CFR 516.31 - Industrial homeworkers.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 29 Labor 3 2013-07-01 2013-07-01 false Industrial homeworkers. 516.31 Section 516.31 Labor... Act; Other Special Requirements § 516.31 Industrial homeworkers. (a) Definitions—(1) Industrial... perform industrial homework for an employer. (2) Industrial homework, as used in this section, means...

  4. 29 CFR 516.31 - Industrial homeworkers.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 3 2014-07-01 2014-07-01 false Industrial homeworkers. 516.31 Section 516.31 Labor... Act; Other Special Requirements § 516.31 Industrial homeworkers. (a) Definitions—(1) Industrial... perform industrial homework for an employer. (2) Industrial homework, as used in this section, means...

  5. 29 CFR 516.31 - Industrial homeworkers.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 29 Labor 3 2012-07-01 2012-07-01 false Industrial homeworkers. 516.31 Section 516.31 Labor... Act; Other Special Requirements § 516.31 Industrial homeworkers. (a) Definitions—(1) Industrial... perform industrial homework for an employer. (2) Industrial homework, as used in this section, means...

  6. Interfacial phenomena in the reactions of Al-B, Al-Ti-B, and Al-Zr-B alloys with KF-AlF{sub 3} and NaF-AlF{sub 3} melts

    SciTech Connect

    Lee, M.S.; Terry, B.S.; Grieveson, P.

    1993-12-01

    The interfacial phenomena occurring during the contacting of liquid Al-B, Al-Ti-B, and Al-Zr-B melts with KF-AlF{sub 3} liquid fluxes have been investigated by optical examination of quenched metal drops previously immersed in the liquid fluxes. Reactions in the Al-B/KF-AlF{sub 3} system involve the formation of metastable AlB{sub 12} at the metal/flux interface. At high KBF{sub 4} levels in the flux, the AlB{sub 12} is dispersed in the flux and also at low KBF{sub 4} levels in the metal. Reactions in the Al-Ti-B/KF-AlF{sub 3} system involve the formation of TiB{sub 2}, which may be dispersed in either the metal or the flux depending upon the composition of the flux. The results obtained for the Al-Ti-B/NaF-AlF{sub 3} and Al-Zr-B/KF-AlF{sub 3} systems were similar to those observed for the Al-Ti-B/KF-AlF{sub 3} system.

  7. Alumina polymorphs affect the metal immobilization effect when beneficially using copper-bearing industrial sludge for ceramics.

    PubMed

    Tang, Yuanyuan; Lu, Xiuqing; Shih, Kaimin

    2014-12-01

    The feasibility of recycling copper-bearing industrial sludge as a part of ceramic raw materials was evaluated through thermal interaction of sludge with aluminum-rich precursors. To observe copper incorporation mechanism, mixtures of copper-bearing sludge with alumina polymorphs (γ-Al2O3 and α-Al2O3) were fired between 750 and 1250°C. Different copper-hosting phases were identified by X-ray diffraction, and CuAl2O4 was found to be the predominant phase throughout the reactions. The experimental results indicate different CuAl2O4 initiating temperatures for two alumina materials, and the optimal temperature for CuAl2O4 formation is around 1100°C. To monitor the stabilization effect, prolonged leaching tests were carried out to leach sintered products for up to 20d. The results clearly demonstrate a substantial decrease in copper leachability for products with higher CuAl2O4 content formed from both alumina precursors despite their different sintering behavior. Meanwhile, the leachability of aluminum was much lower than that of copper, and it decreased by more than fourfold through the formation of CuAl2O4 spinel in γ-Al2O3 system. This study clearly indicates spinel formation as the most crucial metal stabilization mechanism when sintering multiphase copper-bearing industrial sludge with aluminum-rich ceramic raw materials, and suggests a promising and reliable technique for reusing industrial sludge.

  8. Aerospatiale industrial thermal plasma activities

    NASA Astrophysics Data System (ADS)

    Labrot, Maxime

    Details of nontransferred arc torches, plasma systems in industrial use and operational plasma applications are listed. A plasma application on a foundry cupola is detailed. The setting up of a plasma system is described. Research and development activities are summarized.

  9. Production Methods in Industrial Microbiology.

    ERIC Educational Resources Information Center

    Gaden, Elmer L., Jr.

    1981-01-01

    Compares two methods (batch and continuous) in which microorganisms are used to produce industrial chemicals. Describes batch and continuous stirred-tank reactors and offers reasons why the batch method may be preferred. (JN)

  10. Industrial Robots on the Line.

    ERIC Educational Resources Information Center

    Ayres, Robert; Miller, Steve

    1982-01-01

    Explores the history of robotics and its effects upon the manufacturing industry. Topics include robots' capabilities and limitations, the factory of the future, displacement of the workforce, and implications for management and labor. (SK)

  11. Irish medical device industry update.

    PubMed

    Higgins, Sharon

    2005-12-01

    The continued growth of the Irish medical technology industry has not been accidental. The sector is proactive in its drive for excellence in all aspects of the business, from concept to commercialisation. This reports on some recent initiatives.

  12. Nanomedicine: Industry-wise research

    NASA Astrophysics Data System (ADS)

    Eaton, Mike

    2007-04-01

    Academic participation in nanomedicine research is welcomed by European industries. The recipe for success may or may not include creativity, but it will certainly require awareness of drug development and approval processes.

  13. Sex Equity in Industrial Arts.

    ERIC Educational Resources Information Center

    Boben, Donna K.; Ray, Willis E.

    1982-01-01

    It should be industrial arts' long-range goal for the 1980s to change those subtle and pervasive attitudes that have limited female enrollments and extend the benefits and experiences of technology to all students. (CT)

  14. Opportunities in the Turfgrass Industry

    ERIC Educational Resources Information Center

    Campbell, W. F.; Long, G. A.

    1974-01-01

    The growth and development of the turfgrass industry makes it an increasingly important source of employment for vocational agriculture students in the areas of professional and research worker, managerial occupations, landscape contractor, technical superintendents and service workers. (EA)

  15. Campus/Industry Joint Ventures.

    ERIC Educational Resources Information Center

    McDonald, Eugene J.

    1985-01-01

    Opportunities for joint economic ventures of colleges and industry are discussed, and a variety of ventures undertaken by Duke University are outlined, including a health club, hotel, and office building. Tax and financing considerations are noted. (MSE)

  16. Industrial Demand Module - NEMS Documentation

    EIA Publications

    2014-01-01

    Documents the objectives, analytical approach, and development of the National Energy Modeling System (NEMS) Industrial Demand Module. The report catalogues and describes model assumptions, computational methodology, parameter estimation techniques, and model source code.

  17. Industry perspective on regulation issues

    SciTech Connect

    Myrick, C.

    1994-12-31

    Current industry estimates indicate that regulatory compliance costs for retail crop protection chemical and fertilizer dealers will on average increase 300% from 1990 to 1997. Even though recent studies show that most dealers are willing to proactively comply with environmental and worker safety regulations, the impact of over-regulation could be substantial. The agrichemical industry must begin to develop and implement a strategy to increase compliance with needed regulations and prohibit duplicative or unnecessary regulations.

  18. Representing revolution: icons of industrialization.

    PubMed

    Fara, Patricia

    2006-03-01

    Appreciating pictures entails a consideration not only of the people, objects and landscape that their artists have chosen to portray, but also an imagining of what has been excluded. The term 'Industrial Revolution' has been given multiple meanings, and this article (part of the Science in the Industrial Revolution series) explores some of these by exposing the messages concealed inside some of the most enduring images of the Revolution.

  19. Growth and Stress-induced Transformation of Zinc blende AlN Layers in Al-AlN-TiN Multilayers

    PubMed Central

    Li, Nan; Yadav, Satyesh K.; Wang, Jian; Liu, Xiang-Yang; Misra, Amit

    2015-01-01

    AlN nanolayers in sputter deposited {111}Al/AlN/TiN multilayers exhibit the metastable zinc-blende-structure (z-AlN). Based on density function theory calculations, the growth of the z-AlN is ascribed to the kinetically and energetically favored nitridation of the deposited aluminium layer. In situ nanoindentation of the as-deposited {111}Al/AlN/TiN multilayers in a high-resolution transmission electron microscope revealed the z-AlN to wurzite AlN phase transformation through collective glide of Shockley partial dislocations on every two {111} planes of the z-AlN. PMID:26681109

  20. Growth and stress-induced transformation of zinc blende AlN layers in Al-AlN-TiN multilayers

    DOE PAGESBeta

    Li, Nan; Yadav, Satyesh K.; Wang, Jian; Liu, Xiang -Yang; Misra, Amit

    2015-12-18

    We report that AlN nanolayers in sputter deposited {111}Al/AlN/TiN multilayers exhibit the metastable zinc-blende-structure (z-AlN). Based on density function theory calculations, the growth of the z-AlN is ascribed to the kinetically and energetically favored nitridation of the deposited aluminium layer. In situ nanoindentation of the as-deposited {111}Al/AlN/TiN multilayers in a high-resolution transmission electron microscope revealed the z-AlN to wurzite AlN phase transformation through collective glide of Shockley partial dislocations on every two {111} planes of the z-AlN.

  1. The Industrial Ecology of Materials

    NASA Astrophysics Data System (ADS)

    Frosch, Robert A.

    1996-03-01

    Industrial Ecology designates a systems view of material and energy flows in the industrial system, and between the industrial system and the environment. The title and theme are by analogy with natural ecosystems. Within the framework of sustainability, (the possibility of long term high quality human life in an excellent global environment), industrial ecologists examine possibilities for moving from open flow materials systems towards closed loop systems. This shift is intended to be both a means of lightening the environmental burdens arising from processes and products, and a means of approaching long term sustainability of materials use. Using fundamental physical and chemical principles, and some business experiences, industrial ecologists suggest that the reuse of wastes, products, parts, components, and materials is likely to be an environmentally and economically beneficial strategy. The strategy could be improved with some technological and business developments. While there are interesting advantages to this rapidly developing approach, and from the ideas and tools being used within it, a number of problems also arise for industry, consumers and the framers of public policy.

  2. Thermal conductivity of PVD TiAlN films using pulsed photothermal reflectance technique

    NASA Astrophysics Data System (ADS)

    Ding, Xing-Zhao; Samani, M. K.; Chen, George

    2010-11-01

    In the present work, we have measured thermal-conductivity of industrial thin film TiAlN with a thickness of around 3 μm. These films are used in machining industry for cutting tools in order to increase their service life. A series of TiAlN coating with a different Al/Ti atomic ratio were deposited on Fe-304 stainless steel (AISI304) substrate by a lateral rotating cathode arc process. The samples were then coated with a 0.8 μm gold layer on top by magnetron sputtering. We present the thermal-conductivity measurement of these samples using pulsed photothermal reflectance (PPR) technique at room temperature. The thermal conductivity of the pure TiN coating is about 11.9 W/mK. A significant decrease in thermal conductivity was found with increasing Al/Ti atomic ratio. A minimum thermal conductivity of about 4.63 W/mK was obtained at the Al/Ti atomic ratio of around 0.72.

  3. Hydrochemical processes regulating groundwater quality in the coastal plain of Al Musanaah, Sultanate of Oman

    NASA Astrophysics Data System (ADS)

    Askri, Brahim

    2015-06-01

    The Al Batinah coastal aquifer is the principal source of water in northwestern Oman. The rainfall in the Jabal Al Akhdar mountain region recharges the plain with freshwater that allowed agricultural and industrial activities to develop. The over-exploitation of this aquifer since the 1970s for municipal, agricultural and industrial purposes, excessive use of fertilizers in agriculture and leakage from septic tanks led to the deterioration of groundwater quality. The objective of this study was to investigate the hydrochemical processes regulating the groundwater quality in the southwestern section of Al Batinah. From available data collected during the spring of 2010 from 58 wells located in Al Musanaah wilayat, it was determined that the groundwater salinity increased in the direction from the south to the north following the regional flow direction. In addition to salinisation, the groundwater in the upstream and intermediate regions was contaminated with nitrate, while groundwater in the downstream region was affected by fluoride. Calculations of ionic ratios and seawater fraction indicated that seawater intrusion was not dominant in the study area. The primary factors controlling the groundwater chemistry in Al Musanaah appear to be halite dissolution, reverse ion exchange with clay material and anthropogenic pollutants.

  4. Mechanical alloying of nb-al powders

    NASA Astrophysics Data System (ADS)

    Peng, Zhixue; Suryanarayana, C.; Froes, F. H. (Sam)

    1996-01-01

    The effect of mechanical alloying (MA) on solid solubility extension, nanostructure formation, amorphization, intermetallic compound formation, and the occurrence of a face-centered cubic (fcc) phase in the Nb-Al system has been studied. Solid solubility extension was observed in both the terminal compositions and intermetallic compounds: 15 pct Nb in Al and 60 pct Al in Nb, well beyond the equilibrium and even rapid solidification levels (2.4 pct Nb and 25 pct Al, respectively) and increased homogeneity range for the NbAl3 phase. Nanostructured grains formed in all compositions. In the central part of the phase diagram, amorphization occurred predominantly. Only NbAl3, the most stable intermetallic, formed during MA; in most cases, a subsequent anneal was required. On long milling time, an fcc phase, probably a nitride, formed as a result of contamination from the ambient atmosphere.

  5. Mechanical alloying of Nb-Al powders

    SciTech Connect

    Peng, Z.; Suryanarayana, C.; Froes, F.H.

    1996-01-01

    The effect of mechanical alloying (MA) on solid solubility extension, nanostructure formation, amorphization, intermetallic compound formation, and the occurrence of a face-centered cubic (fcc) phase in the Nb-Al system has been studied. Solid solubility extension was observed in both the terminal compositions and intermetallic compounds: 15 pct Nb in Al and 60 pct Al in Nb, well beyond the equilibrium and even rapid solidification levels (2.4 pct Nb and 25 pct Al, respectively) and increased homogeneity range for the NbAl{sub 3} phase. Nanostructured grains formed in all compositions. In the central part of the phase diagram, amorphization occurred predominantly. Only NbAl{sub 3}, the most stable intermetallic, formed during MA; in most cases, a subsequent anneal was required. On long milling time, an fcc phase, probably a nitride, formed as a result of contamination from the ambient atmosphere.

  6. Orientation relationship of eutectoid FeAl and FeAl2

    PubMed Central

    Scherf, A.; Kauffmann, A.; Kauffmann-Weiss, S.; Scherer, T.; Li, X.; Stein, F.; Heilmaier, M.

    2016-01-01

    Fe–Al alloys in the aluminium range of 55–65 at.% exhibit a lamellar microstructure of B2-ordered FeAl and triclinic FeAl2, which is caused by a eutectoid decomposition of the high-temperature Fe5Al8 phase, the so-called ∊ phase. The orientation relationship of FeAl and FeAl2 has previously been studied by Bastin et al. [J. Cryst. Growth (1978 ▸), 43, 745] and Hirata et al. [Philos. Mag. Lett. (2008 ▸), 88, 491]. Since both results are based on different crystallographic data regarding FeAl2, the data are re-evaluated with respect to a recent re-determination of the FeAl2 phase provided by Chumak et al. [Acta Cryst. (2010 ▸), C66, i87]. It is found that both orientation relationships match subsequent to a rotation operation of 180° about a 〈112〉 crystallographic axis of FeAl or by applying the inversion symmetry of the FeAl2 crystal structure as suggested by the Chumak data set. Experimental evidence for the validity of the previously determined orientation relationships was found in as-cast fully lamellar material (random texture) as well as directionally solidified material (∼〈110〉FeAl || solidification direction) by means of orientation imaging microscopy and global texture measurements. In addition, a preferential interface between FeAl and FeAl2 was identified by means of trace analyses using cross sectioning with a focused ion beam. On the basis of these habit planes the orientation relationship between the two phases can be described by (01)FeAl || (114) and [111]FeAl || [10]. There is no evidence for twinning within FeAl lamellae or alternating orientations of FeAl lamellae. Based on the determined orientation and interface data, an atomistic model of the structure relationship of Fe5Al8, FeAl and FeAl2 in the vicinity of the eutectoid decomposition is derived. This model is analysed with respect to the strain which has to be accommodated at the interface of FeAl and FeAl2. PMID:27047304

  7. A New Phase in ALS Research.

    PubMed

    Chong, P Andrew; Forman-Kay, Julie D

    2016-09-01

    In this issue of Structure, Conicella et al. (2016) present evidence that the low complexity C-terminal region of TDP-43 undergoes liquid-liquid phase separation. ALS-associated mutations alter this phase separation process, providing a possible mechanism for the pathology caused by these TDP-43 mutations. The work is strongly supportive of toxic loss of RNA processing function in ALS. PMID:27602988

  8. Tensile Behavior of Al2o3/feal + B and Al2o3/fecraly Composites

    NASA Technical Reports Server (NTRS)

    Draper, S. L.; Eldridge, J. I.; Aiken, B. J. M.

    1995-01-01

    The feasibility of Al2O3/FeAl + B and Al2O3/FeCrAlY composites for high-temperature applications was assessed. The major emphasis was on tensile behavior of both the monolithics and composites from 298 to 1100 K. However, the study also included determining the chemical compatibility of the composites, measuring the interfacial shear strengths, and investigating the effect of processing on the strength of the single-crystal Al2O3 fibers. The interfacial shear strengths were low for Al203/FeAl + B and moderate to high for Al203/FeCrAlY. The difference in interfacial bond strengths between the two systems affected the tensile behavior of the composites. The strength of the Al203 fiber was significantly degraded after composite processing for both composite systems and resulted in poor composite tensile properties. The ultimate tensile strength (UTS) values of the composites could generally be predicted with either rule of mixtures (ROM) calculations or existing models when using the strength of the etched-out fiber. The Al2O3/FeAl + B composite system was determined to be unfeasible due to poor interfacial shear strengths and a large mismatch in coefficient of thermal expansion (CTE). Development of the Al2O3/FeCrAlY system would require an effective diffusion barrier to minimize the fiber strength degradation during processing and elevated temperature service.

  9. Market Report for the Industrial Sector, 2009

    SciTech Connect

    Sastri, Bhima; Brueske, Sabine; de los Reyes, Pamela; Jamison, Keith; Justiniano, Mauricio; Margolis, Nancy; Monfort, Joe; Raghunathan, Anand; Sabouni, Ridah

    2009-07-01

    This report provides an overview of trends in industrial-sector energy use. It focuses on some of the largest and most energy-intensive industrial subsectors and several emerging technologies that could transform key segments of industry.

  10. Memory deficits and retrieval processes in ALS.

    PubMed

    Mantovan, M C; Baggio, L; Dalla Barba, G; Smith, P; Pegoraro, E; Soraru', G; Bonometto, P; Angelini, C

    2003-05-01

    Subtle neuropsychological deficits have been described in patients affected by amyotrophic lateral sclerosis (ALS) without dementia. Overall, selective impairment in memory function has been reported, but the source of memory impairment in ALS has yet to be defined. We performed neuropsychological screening in 20 ALS patients. Semantic encoding and post-encoding cue effects on the retrieval of word lists were investigated in the ALS patients and normal controls. Severity of memory impairment was correlated to cerebral blood perfusion detected by single photon emission computed tomography (SPECT). ALS patients showed moderate impairments in frontal and memory tests. Short-term memory was normal, while serial position retrieval of word lists with normal recency effect but poor primacy effect showed long-term memory deficit. ALS patients performed better in cued encoding than in cued post-encoding recall condition. In the cued post-encoding condition, the primacy effect in word list recall improved significantly in controls, but not in ALS patients, as compared with both the free recall and cued encoding conditions. SPECT hypoperfusion was observed in frontal and temporal areas in ALS patients. ALS patients showed a long-term memory deficit which did not improve in cued post-encoding condition as it does for controls. We hypothesize abnormal retrieval processes related to frontal lobe dysfunction which entails difficulties in generating stable long-memory traces at encoding.

  11. Memory deficits and retrieval processes in ALS.

    PubMed

    Mantovan, M C; Baggio, L; Dalla Barba, G; Smith, P; Pegoraro, E; Soraru', G; Bonometto, P; Angelini, C

    2003-05-01

    Subtle neuropsychological deficits have been described in patients affected by amyotrophic lateral sclerosis (ALS) without dementia. Overall, selective impairment in memory function has been reported, but the source of memory impairment in ALS has yet to be defined. We performed neuropsychological screening in 20 ALS patients. Semantic encoding and post-encoding cue effects on the retrieval of word lists were investigated in the ALS patients and normal controls. Severity of memory impairment was correlated to cerebral blood perfusion detected by single photon emission computed tomography (SPECT). ALS patients showed moderate impairments in frontal and memory tests. Short-term memory was normal, while serial position retrieval of word lists with normal recency effect but poor primacy effect showed long-term memory deficit. ALS patients performed better in cued encoding than in cued post-encoding recall condition. In the cued post-encoding condition, the primacy effect in word list recall improved significantly in controls, but not in ALS patients, as compared with both the free recall and cued encoding conditions. SPECT hypoperfusion was observed in frontal and temporal areas in ALS patients. ALS patients showed a long-term memory deficit which did not improve in cued post-encoding condition as it does for controls. We hypothesize abnormal retrieval processes related to frontal lobe dysfunction which entails difficulties in generating stable long-memory traces at encoding. PMID:12752394

  12. Genetics of Familial and Sporadic ALS

    ClinicalTrials.gov

    2016-03-21

    Amyotrophic Lateral Sclerosis (ALS); Familial Amyotrophic Lateral Sclerosis; Amyotrophic Lateral Sclerosis With Frontotemporal Dementia; Lou Gehrig's Disease; Motor Neuron Disease; Primary Lateral Sclerosis

  13. Superbend era begins swiftly at the ALS

    SciTech Connect

    Robinson, Art; Tamura, Lori

    2001-11-29

    The successful installation and commissioning of high-field superconducting bend magnets (superbends) in three curved sectors of ALS storage ring was the first time the magnet lattice of an operating synchrotron light source has been retrofitted in this fundamental way. As a result, the ALS now offers an expanded spectral range well into the hard x-ray region without compromising either the number of undulators or their high brightness in the soft x-ray region for which the ALS design was originally optimized. In sum, when the superbend-enhanced ALS started up for user operations in October 2001, it marked the beginning of a new era in its history.

  14. Effects of the Al content on pore structures of porous TieAl alloys

    SciTech Connect

    Jiang, Y; He, Y H; Zou, J; Huang, B; Liu, C

    2008-01-01

    PorousTi Alalloys with different nominal compositions were fabricated through a reactive synthesis of Ti and Al elemental powders. It has been found that the pore parameters vary with the Al contents, indicating that the nature of the pores can be manipulated through changing the Al contents. In addition, detailed structural characterizations showed that the fabricated porousTi Alalloys can have three crystalline phases (i.e., 2-Ti3Al, -TiAl, and TiAl3) when using different compositions. The fundamental reasons behind these phenomena have been explored.

  15. Response to Signorovitch et al.

    PubMed

    Flot, Jean-François; Debortoli, Nicolas; Hallet, Bernard; Van Doninck, Karine

    2016-08-22

    Signorovitch et al.[1] comment that an Oenothera-like meiosis [2] could produce a pattern similar to what we observed in our study of natural isolates of the bdelloid rotifer Adineta vaga, which we attributed to horizontal gene transfers (HGTs) [3]. Indeed, our HGT hypothesis appears at first sight difficult to conciliate with their observation of a congruent pattern of allele sharing at four large loci possibly located on different chromosomes [4]. However, one might imagine conditions under which massive horizontal gene transfer between bdelloid individuals could produce such a pattern, notably if the individuals involved had previously lost most of their heterozygosity because of their exposure to frequent desiccation (which produces DNA double-strand breaks [5]). In the published A. vaga genome the loss of heterozygosity due to large-scale gene conversion events or break-induced replication covers only about 10% of the genome [6], but this percentage may be much higher in environmental isolates that often experience dessication. Besides, if an Oenothera-like mode of meiosis occurs in bdelloids frequently enough to be detected in a single sampling of 29 individuals (as in [4]), one would expect males and meiosis to be observed at least occasionally, and instances of congruent allele sharing across loci should turn up frequently in genetic surveys. This was not the case in [3]: among the 82 A. vaga individuals sequenced for four nuclear markers, no trio of individuals presented congruent patterns of shared sequences at different loci. For these reasons, and in the absence of any direct evidence for an Oenothera-like meiosis in bdelloids, we still consider inter-bdelloid HGTs a more parsimonious explanation for our results. PMID:27554651

  16. The Aeronautics Education, Research, and Industry Alliance (AERIAL) 2002 Report. UNO Aviation Monograph Series. UNOAI Report.

    ERIC Educational Resources Information Center

    Bowen, Brent D.; Box, Richard C.; Fink, Mary M.; Gogos, George; Lehrer, Henry R.; Narayanan, Ram M.; Nickerson, Jocelyn S.; O'Neil, Patrick D.; Tarry, Scott E.; Vlasek, Karisa D.

    This document contains four papers on aeronautics education, research, and partnerships that partly supported through the Aeronautics Education, Research, and Industry Alliance (AERIAL). The paper "2002 AERIAL Monograph" (Brent D. Bowen, Jocelyn S. Nickerson, Mary M. Fink, et al.) presents an overview of research and development in the following…

  17. Industry Raps OSHA's Proposed Cancer Policy

    ERIC Educational Resources Information Center

    Chemical and Engineering News, 1978

    1978-01-01

    Presents the response of the American Industrial Health Council (AIHC) to the Occupational Safety and Health Administration's (OSHA's) genetic proposal for regulating chemical carcinogens in industry. (HM)

  18. University Research Gets Boost from Industry Funds.

    ERIC Educational Resources Information Center

    Physics Today, 1982

    1982-01-01

    Reviews current and future research endeavors supported by funds from industry focusing on research and development centers at various universities and industries which support scientific research. (SK)

  19. Industry involvement in IPAD through the Industry Technical Advisory Board

    NASA Technical Reports Server (NTRS)

    Swanson, W. E.

    1980-01-01

    In 1976 NASA awarded The Boeing Company a contract to develop IPAD (Integrated Programs for Aerospace-Vehicle Design). This contract included a requirement for Boeing to form an Industrial Technical Advisory Board (ITAB), with members representing major aerospace and computer companies. The purpose of this board was to guide the development of IPAD. The specific goal of IPAD is to increase United States aerospace industry productivity through the application of computers to manage engineering data. This goal clearly is attainable; in fact, IPAD's influence can reach beyond the aerospace industry to many businesses where product development is based on the design-building process. An enhanced IPAD, therefore, is a national asset of significance. The role of ITAB in guiding the development of this system is described.

  20. Atomic structure and oxygen deficiency of the ultrathin aluminium oxide barrier in Al/AlOx/Al Josephson junctions

    NASA Astrophysics Data System (ADS)

    Zeng, Lunjie; Tran, Dung Trung; Tai, Cheuk-Wai; Svensson, Gunnar; Olsson, Eva

    2016-07-01

    Al/AlOx/Al Josephson junctions are the building blocks of a wide range of superconducting quantum devices that are key elements for quantum computers, extremely sensitive magnetometers and radiation detectors. The properties of the junctions and the superconducting quantum devices are determined by the atomic structure of the tunnel barrier. The nanoscale dimension and disordered nature of the barrier oxide have been challenges for the direct experimental investigation of the atomic structure of the tunnel barrier. Here we show that the miniaturized dimension of the barrier and the interfacial interaction between crystalline Al and amorphous AlOx give rise to oxygen deficiency at the metal/oxide interfaces. In the interior of the barrier, the oxide resembles the atomic structure of bulk aluminium oxide. Atomic defects such as oxygen vacancies at the interfaces can be the origin of the two-level systems and contribute to decoherence and noise in superconducting quantum circuits.

  1. Strengthening of Al and Al-Mg alloy wires by melt inoculation with Al/MgB2 nanocomposite

    NASA Astrophysics Data System (ADS)

    Florián-Algarín, David; Marrero, Raúl; Padilla, Alexandra; Suárez, Oscar Marcelo

    2015-12-01

    This study hinges on the feasibility of strengthening Al and Al-Mg wires by adding Al nanocomposite pellets containing MgB2 nanoparticles into the melt upon fabrication. These MgB2 nanoparticles were obtained by fragmentation using a high-energy ball mill, and were, afterward, mechanically alloyed with pure aluminum. The resulting MgB2/Al nanocomposite pellets were sintered at 260°C to be subsequently added into molten aluminum and an Al-Mg alloy melt. Cold rolling intercalated with stepwise annealing allowed the fabrication of 1 mm diameter wires with a final area reduction of 96%. Mechanical and physical properties of the treated wire specimens were compared to those of similarly processed pure aluminum wire. The ultimate tensile strength of the treated wires increased approximately double fold with respect to untreated wires at the expense of some loss in electrical conductivity.

  2. Atomic structure and oxygen deficiency of the ultrathin aluminium oxide barrier in Al/AlOx/Al Josephson junctions.

    PubMed

    Zeng, Lunjie; Tran, Dung Trung; Tai, Cheuk-Wai; Svensson, Gunnar; Olsson, Eva

    2016-01-01

    Al/AlOx/Al Josephson junctions are the building blocks of a wide range of superconducting quantum devices that are key elements for quantum computers, extremely sensitive magnetometers and radiation detectors. The properties of the junctions and the superconducting quantum devices are determined by the atomic structure of the tunnel barrier. The nanoscale dimension and disordered nature of the barrier oxide have been challenges for the direct experimental investigation of the atomic structure of the tunnel barrier. Here we show that the miniaturized dimension of the barrier and the interfacial interaction between crystalline Al and amorphous AlOx give rise to oxygen deficiency at the metal/oxide interfaces. In the interior of the barrier, the oxide resembles the atomic structure of bulk aluminium oxide. Atomic defects such as oxygen vacancies at the interfaces can be the origin of the two-level systems and contribute to decoherence and noise in superconducting quantum circuits. PMID:27403611

  3. Atomic structure and oxygen deficiency of the ultrathin aluminium oxide barrier in Al/AlOx/Al Josephson junctions

    PubMed Central

    Zeng, Lunjie; Tran, Dung Trung; Tai, Cheuk-Wai; Svensson, Gunnar; Olsson, Eva

    2016-01-01

    Al/AlOx/Al Josephson junctions are the building blocks of a wide range of superconducting quantum devices that are key elements for quantum computers, extremely sensitive magnetometers and radiation detectors. The properties of the junctions and the superconducting quantum devices are determined by the atomic structure of the tunnel barrier. The nanoscale dimension and disordered nature of the barrier oxide have been challenges for the direct experimental investigation of the atomic structure of the tunnel barrier. Here we show that the miniaturized dimension of the barrier and the interfacial interaction between crystalline Al and amorphous AlOx give rise to oxygen deficiency at the metal/oxide interfaces. In the interior of the barrier, the oxide resembles the atomic structure of bulk aluminium oxide. Atomic defects such as oxygen vacancies at the interfaces can be the origin of the two-level systems and contribute to decoherence and noise in superconducting quantum circuits. PMID:27403611

  4. Atomic structure and oxygen deficiency of the ultrathin aluminium oxide barrier in Al/AlOx/Al Josephson junctions.

    PubMed

    Zeng, Lunjie; Tran, Dung Trung; Tai, Cheuk-Wai; Svensson, Gunnar; Olsson, Eva

    2016-07-12

    Al/AlOx/Al Josephson junctions are the building blocks of a wide range of superconducting quantum devices that are key elements for quantum computers, extremely sensitive magnetometers and radiation detectors. The properties of the junctions and the superconducting quantum devices are determined by the atomic structure of the tunnel barrier. The nanoscale dimension and disordered nature of the barrier oxide have been challenges for the direct experimental investigation of the atomic structure of the tunnel barrier. Here we show that the miniaturized dimension of the barrier and the interfacial interaction between crystalline Al and amorphous AlOx give rise to oxygen deficiency at the metal/oxide interfaces. In the interior of the barrier, the oxide resembles the atomic structure of bulk aluminium oxide. Atomic defects such as oxygen vacancies at the interfaces can be the origin of the two-level systems and contribute to decoherence and noise in superconducting quantum circuits.

  5. Processing of nickel aluminides and their industrial applications

    SciTech Connect

    Sikka, V.K. ); Mavity, J.T.; Anderson, K. )

    1991-01-01

    Ductile Ni{sub 3}Al-based alloys offer unique properties. However, their use has been limited because information is lacking regarding their processing into various product forms. This paper describes the recent progress made toward melting, electroslag remelting, and the processing of large-scale ingots of one of the Ni{sub 3}Al-based alloys. Microstructural data are presented after various homogenization treatments. Both as-cast and homogenized samples were subjected to hot-compression testing. The hot-compression data for the commercial-size ingot showed the same behavior as previously reported on the experimental heats. The status of industrial applications of nickel-aluminide alloys is also described. 12 refs., 12 figs., 2 tabs.

  6. Influence of AlN thickness on AlGaN epilayer grown by MOCVD

    NASA Astrophysics Data System (ADS)

    Jayasakthi, M.; Juillaguet, S.; Peyre, H.; Konczewicz, L.; Baskar, K.; Contreras, S.

    2016-10-01

    AlGaN/AlN layers were grown by metalorganic chemical vapor deposition (MOCVD) on sapphire substrates. The AlN buffer thickness was varied from 400 nm to 800 nm. The AlGaN layer thickness was 1000 nm. The crystalline quality, thickness and composition of AlGaN were determined using high resolution X-ray diffraction (HRXRD). The threading dislocation density (TDD) was found to decrease with increase of AlN layer thickness. Reciprocal space mapping (RSM) was used to estimate the strain and relaxation between AlGaN and AlN. The optical properties of AlGaN layers were investigated by temperature dependent photoluminescence (PL). PL intensities of AlGaN layers increases with increasing the AlN thickness. The surface morphology of AlGaN was studied by atomic force microscopy (AFM). Root mean square (RMS) roughness values were found to be decreased while increase of AlN thickness.

  7. Superplastics properties of an Al-2. 4Mg-1. 8Li-0. 5Sc alloy

    SciTech Connect

    Bradley, E.L. III; Emigh, R.A.; Morris, J.W. Jr. . Dept. of Materials Science and Engineering Lawrence Berkeley Lab., CA . Center for Advanced Materials)

    1991-01-01

    There is a need in the aerospace industry for structural, superplastic aluminum alloys that are formable at strain-rates greater than 10[sup [minus]3] s[sup [minus]1] in order for the economic benefits of superplastic forming to be realized. The standard, structural, superplastic aluminum alloy in the aerospace industry is 7475, which has an optimum forming strain-rate near 10[sup [minus]4] s[sup [minus]1]. Thus, research has been focused on modifying the microstructures of wrought Al-Li alloys such as 2090 and 8090 into superplastically formable (SPF) microstructures with improved properties, but the results have not been completely successful. Superplastic alloys with high strengths have been produced from the Al-Mg-Sc system. These alloys are strengthened by thermomechanical processing which (1) precipitates small, coherent Al[sub 3]Sc particles and (2) increases the dislocation density of the material. The Mg is in solid solution and improves the work hardening capability of these alloys. Because superplastic forming is carried out at relatively high temperatures, recovery processes eliminate the dislocation strengthening resulting from the rolling and overage the precipitates. Thus, additional precipitation strengthening is required to make these alloys attractive for use in aerospace applications. Lithium provides the most promising choice since it forms the ordered coherent precipitate [delta][prime] (Al[sub 3]Li), lowers the density, and increases the stiffness of aluminum alloys. In addition, at low concentrations, Li should be in solution at the SPF temperatures and should have little effect on the superplastic formability of the alloys. This led to research on alloys from the Al-Mg-Li-Sc system. This paper describes the preliminary high-temperature tensile results of an Al-Mg-Li-Sc alloy and relates them to other superplastic Al alloys.

  8. Export industry structure upgrading and China's vertical specialization

    NASA Astrophysics Data System (ADS)

    Meng, Yinghua

    2011-10-01

    We computed the ratio of China's vertical specialization with revising method of Hummels et al. (2001). We found that China's export has the traits of processing trade, and Asian countries are the main exporter of intermediate goods to China; there is strong positive relationship between export ratio and ratio of China's vertical specialization, indicates that importing of intermediate goods play an important role in China's industry upgrading, China's comparative advantage of export still lies in low price of labor; even if China's production still locates in low value added stage in international supply chain, but China has began to advance its industry structure, and change the mode of production and trade that rely processing trade too much.

  9. Systems Biology of Industrial Microorganisms

    NASA Astrophysics Data System (ADS)

    Papini, Marta; Salazar, Margarita; Nielsen, Jens

    The field of industrial biotechnology is expanding rapidly as the chemical industry is looking towards more sustainable production of chemicals that can be used as fuels or building blocks for production of solvents and materials. In connection with the development of sustainable bioprocesses, it is a major challenge to design and develop efficient cell factories that can ensure cost efficient conversion of the raw material into the chemical of interest. This is achieved through metabolic engineering, where the metabolism of the cell factory is engineered such that there is an efficient conversion of sugars, the typical raw materials in the fermentation industry, into the desired product. However, engineering of cellular metabolism is often challenging due to the complex regulation that has evolved in connection with adaptation of the different microorganisms to their ecological niches. In order to map these regulatory structures and further de-regulate them, as well as identify ingenious metabolic engineering strategies that full-fill mass balance constraints, tools from systems biology can be applied. This involves both high-throughput analysis tools like transcriptome, proteome and metabolome analysis, as well as the use of mathematical modeling to simulate the phenotypes resulting from the different metabolic engineering strategies. It is in fact expected that systems biology may substantially improve the process of cell factory development, and we therefore propose the term Industrial Systems Biology for how systems biology will enhance the development of industrial biotechnology for sustainable chemical production.

  10. [Genome editing of industrial microorganism].

    PubMed

    Zhu, Linjiang; Li, Qi

    2015-03-01

    Genome editing is defined as highly-effective and precise modification of cellular genome in a large scale. In recent years, such genome-editing methods have been rapidly developed in the field of industrial strain improvement. The quickly-updating methods thoroughly change the old mode of inefficient genetic modification, which is "one modification, one selection marker, and one target site". Highly-effective modification mode in genome editing have been developed including simultaneous modification of multiplex genes, highly-effective insertion, replacement, and deletion of target genes in the genome scale, cut-paste of a large DNA fragment. These new tools for microbial genome editing will certainly be applied widely, and increase the efficiency of industrial strain improvement, and promote the revolution of traditional fermentation industry and rapid development of novel industrial biotechnology like production of biofuel and biomaterial. The technological principle of these genome-editing methods and their applications were summarized in this review, which can benefit engineering and construction of industrial microorganism.

  11. Diana Al-Hadid: Identity and Heritage

    ERIC Educational Resources Information Center

    Jungerberg, Tom; Smith, Anna; Borsh, Colleen

    2012-01-01

    Diana Al-Hadid's sculptures reflect the many locations, cultures, histories, and mythologies that have shaped her as an artist. In large-scale works which have the appearance of architectural ruins, Al-Hadid employs imagery drawn from many diverse interests including science and technology, history, and literature. She also incorporates images and…

  12. Quantitatively Probing the Al Distribution in Zeolites

    SciTech Connect

    Vjunov, Aleksei; Fulton, John L.; Huthwelker, Thomas; Pin, Sonia; Mei, Donghai; Schenter, Gregory K.; Govind, Niranjan; Camaioni, Donald M.; Hu, Jian Z.; Lercher, Johannes A.

    2014-06-11

    The degree of substitution of Si4+ by Al3+ in the oxygen-terminated tetrahedra (Al T-sites) of zeolites determines the concentration of ion-exchange and Brønsted acid sites. As the location of the tetrahedra and the associated subtle variations in bond angles influence the acid strength, quantitative information about Al T-sites in the framework is critical to rationalize catalytic properties and to design new catalysts. A quantitative analysis is reported that uses a combination of extended X-ray absorption fine structure (EXAFS) analysis and 27Al MAS NMR spectroscopy supported by DFT-based molecular dynamics simulations. To discriminate individual Al atoms, sets of ab initio EXAFS spectra for various T-sites are generated from DFT-based molecular dynamics simulations allowing quantitative treatment of the EXAFS single- and multiple-photoelectron scattering processes out to 3-4 atom shells surrounding the Al absorption center. It is observed that identical zeolite types show dramatically different Al-distributions. A preference of Al for T-sites that are part of one or more 4-member rings in the framework over those T-sites that are part of only 5- and 6-member rings in the HBEA150 sample has been determined from a combination of these methods. This work was supported by the U. S. Department of Energy (DOE), Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences & Biosciences.

  13. Durability Assessment of TiAl Alloys

    NASA Technical Reports Server (NTRS)

    Draper, Susan L.; Lerch, Bradley A.

    2008-01-01

    The durability of TiAl is a prime concern for the implementation of TiAl into aerospace engines. Two durability issues, the effect of high temperature exposure on mechanical properties and impact resistance, have been investigated and the results are summarized in this paper. Exposure to elevated temperatures has been shown to be detrimental to the room temperature ductility of gamma alloys with the most likely mechanisms being the ingress of interstitials from the surface. Fluorine ion implantation has been shown to improve the oxidation resistance of gamma alloys, and ideally it could also improve the environmental embrittlement of high Nb content TiAl alloys. The effect of F ion implantation on the surface oxidation and embrittlement of a third generation, high Nb content TiAl alloy (Ti-45Al-5Nb-B-C) were investigated. Additionally, the ballistic impact resistance of a variety of gamma alloys, including Ti-48Al-2Cr- 2Nb, Ti-47Al-2Cr-2Nb, ABB-2, ABB-23, NCG359E, 95A and Ti-45Al-5Nb-B-C was accessed. Differences in the ballistic impact properties of the various alloys will be discussed, particularly with respect to their manufacturing process, microstructure, and tensile properties.

  14. Energetics of Al13 Keggin cluster compounds

    PubMed Central

    Armstrong, Christopher R.; Casey, William H.; Navrotsky, Alexandra

    2011-01-01

    The ϵ-Al13 Keggin aluminum hydroxide clusters are essential models in establishing molecular pathways for geochemical reactions. Enthalpies of formation are reported for two salts of aluminum centered ϵ-Keggin clusters, Al13 selenate, (Na(AlO4)Al12(OH)24(SeO4)4•12H2O) and Al13 sulfate, (NaAlO4Al12(OH)24(SO4)4•12H2O). The measured enthalpies of solution, ΔHsol, at 28 °C in 5 N HCl for the ε-Al13 selenate and sulfate are −924.57 (± 3.83) and −944.30 ( ± 5.66) kJ·mol-1, respectively. The enthalpies of formation from the elements, ΔHf,el, for Al13 selenate and sulfate are −19,656.35 ( ± 67.30) kJ·mol-1, and −20,892.39 ( ± 70.01) kJ·mol-1, respectively. In addition, ΔHf,el for sodium selenate decahydrate was calculated using data from high temperature oxide melt solution calorimetry measurements: −4,006.39 ( ± 11.91) kJ·mol-1. The formation of both ε-Al13 Keggin cluster compounds is exothermic from oxide-based components but energetically unfavorable with respect to a gibbsite-based assemblage. To understand the relative affinity of the ϵ-Keggin clusters for selenate and sulfate, the enthalpy associated with two S-Se exchange reactions was calculated. In the solid state, selenium is favored in the Al13 compound relative to the binary chalcogenate, while in 5 N HCl, sulfur is energetically favored in the cluster compound compared to the aqueous solution. This contribution represents the first thermodynamic study of ε-Al13 cluster compounds and establishes a method for other such molecules, including the substituted versions that have been created for kinetic studies. Underscoring the importance of ε-Al13 clusters in natural and anthropogenic systems, these data provide conclusive thermodynamic evidence that the Al13 Keggin cluster is a crucial intermediate species in the formation pathway from aqueous aluminum monomers to aluminum hydroxide precipitates. PMID:21852572

  15. NiAl alloys for structural uses

    NASA Technical Reports Server (NTRS)

    Koss, D. A.

    1991-01-01

    Alloys based on the intermetallic compound NiAl are of technological interest as high temperature structural alloys. These alloys possess a relatively low density, high melting temperature, good thermal conductivity, and (usually) good oxidation resistance. However, NiAl and NiAl-base alloys suffer from poor fracture resistance at low temperatures as well as inadequate creep strength at elevated temperatures. This research program explored macroalloying additions to NiAl-base alloys in order to identify possible alloying and processing routes which promote both low temperature fracture toughness and high temperature strength. Initial results from the study examined the additions of Fe, Co, and Hf on the microstructure, deformation, and fracture resistance of NiAl-based alloys. Of significance were the observations that the presence of the gamma-prime phase, based on Ni3Al, could enhance the fracture resistance if the gamma-prime were present as a continuous grain boundary film or 'necklace'; and the Ni-35Al-20Fe alloy was ductile in ribbon form despite a microstructure consisting solely of the B2 beta phase based on NiAl. The ductility inherent in the Ni-35Al-20Fe alloy was explored further in subsequent studies. Those results confirm the presence of ductility in the Ni-35Al-20Fe alloy after rapid cooling from 750 - 1000 C. However exposure at 550 C caused embrittlement; this was associated with an age-hardening reaction caused by the formation of Fe-rich precipitates. In contrast, to the Ni-35Al-20Fe alloy, exploratory research indicated that compositions in the range of Ni-35Al-12Fe retain the ordered B2 structure of NiAl, are ductile, and do not age-harden or embrittle after thermal exposure. Thus, our recent efforts have focused on the behavior of the Ni-35Al-12Fe alloy. A second parallel effort initiated in this program was to use an alternate processing technique, mechanical alloying, to improve the properties of NiAl-alloys. Mechanical alloying in the

  16. Public concern about industrial hazards

    SciTech Connect

    Stallen, P.J.M.; Tomas, A.

    1988-06-01

    In this paper the authors propose adopting a noncognitive perspective for the understanding of people's anxiety or, its opposite, feelings of security about living near hazardous industrial facilities. Results of their empirical investigations among residents of a heavily industrialized area indicate that at least four qualitatively different response patterns exist: the Secure, the Accepting, the Defensive, and the Vigilant response. In this order manifest anxiety increases, which increase is shown to be a function of the assessment of the threat, of the opportunities for personal control (specific), and of hope (generalized) to bring about a better environment by one's own action. As an application of the usefulness of this typology they discuss the various explanations for the often-observed male/female difference in anxiety regarding industrial threat.

  17. Industry liaison section implementation plan

    NASA Technical Reports Server (NTRS)

    Lakowske, Stephen

    1990-01-01

    The Industry Liaison Section is a new function of the Army/NASA Aircrew-Aircraft Integration (AAAI) Program that is intended to bridge an existing gap between Government developers (including contractors) and outside organizations who are potential users of products and services developed by the AAAI Program. Currently in its sixth year, the Program is experiencing considerable pull from industry and other government organizations to disseminate products. Since the AAAI Program's charter is exploratory and research in nature, and satisfying proper dissemination requirements is in conflict with the rapid prototyping approach utilized by the design team, the AAAI Program has elected to create an Industry Liaison Section (ILS) to serve as the Program's technology transfer focal point. The process by which the ILS may be established, organized and managed is described, including the baseline organizational structure, duties, functions, authority, responsibilities, relations and policies and procedures relevant to the conduct of the ILS.

  18. Steel Industry Energy Bandwidth Study

    SciTech Connect

    none,

    2004-10-01

    ITP conducted a study on energy use and potential savings, or "bandwidth" study, in major steelmaking processes. Intended to provide a realistic estimate of the potential amount of energy that can be saved in an industrial process, the "bandwidth" refers to the difference between the amount of energy that would be consumed in a process using commercially available technology versus the minimum amount of energy needed to achieve those same results based on the 2nd law of thermodynamics. The Steel Industry Energy Bandwidth Study (PDF 133 KB) also estimates steel industry energy use in the year 2010, and uses that value as a basis for comparison against the minimum requirements. This energy savings opportunity for 2010 will aid focus on longer term R&D.

  19. A Testing Service for Industry

    NASA Technical Reports Server (NTRS)

    1994-01-01

    A small isolated NASA facility provides assistance to industry in the design, testing, and operation of oxygen systems. White Sands Test Facility (WSTF) was originally established to test rocket propulsion systems for the Apollo program. The facility's role was later expanded into testing characterization, flammability and toxicity characteristics of materials. Its materials and components test methods were adopted by the American society for Testing and Materials. When research and testing results became known, industry requested assistance, and in 1980, NASA authorized WSTF to open its facility to private firms, a valuable service, as oxygen systems testing is often too expensive and too hazardous for many companies. Today, some of the best known American industries utilize White Sands testing capabilities.

  20. Chemistry in the Pharmaceutical Industry

    NASA Astrophysics Data System (ADS)

    Poindexter, Graham S.; Pendri, Yadagiri; Snyder, Lawrence B.; Yevich, Joseph P.; Deshpande, Milind

    This chapter will discuss the role of chemistry within the pharmaceutical industry. Although the focus will be upon the industry within the United States, much of the discussion is equally relevant to pharmaceutical companies based in other first world nations such as Japan and those in Europe. The major objective of the pharmaceutical industry is the discovery, development, and marketing of efficacious and safe drugs for the treatment of human disease. Of course drug companies do not exist as altruistic, charitable organizations but like other share-holder owned corporations within our capitalistic society must achieve profits in order to remain viable and competitive. Thus, there exists a conundrum between the dual goals of enhancing the quality and duration of human life and that of increasing stock-holder equity. Much has been written and spoken in the lay media about the high prices of prescription drugs and the hardships this places upon the elderly and others of limited income.

  1. The chemical industry, by country

    SciTech Connect

    Not Available

    1995-03-01

    Beijing will be the site for the third ACHEMASIA, international petrochemical and chemical exhibition and conference, May 15--20, 1995. In preparation for this conference, Hydrocarbon Processing contacted executives of petrochemical/chemical industries and trade associations, seeking views on the state of the industry. The Asia-Pacific region is the center of new construction and expanded capacity and also a mixture of mature, developing and emerging petrochemical industries. Established countries must mold and grow with emerging economies as the newcomers access natural resources and develop their own petrochemical infrastructures. The following nation reports focus on product supply/demand trends, economic forecasts, new construction, etc. Space limitations prohibit publishing commentaries from all countries that have petrochemical/chemical capacity. Reports are published from the following countries: Australia, China, Japan, Korea, Malaysia, Philippines, Thailand, and Vietnam.

  2. Corrosion Studies of 2195 Al-Li Alloy and 2219 Al Alloy with Differing Surface Treatments

    NASA Technical Reports Server (NTRS)

    Danford, M. D.; Mendrek, M. J.

    1998-01-01

    Corrosion studies of 2195 Al-Li and 2219 Al alloys have been conducted using the scanning reference electrode technique (SRET) and the polarization resistance (PR) technique. The SRET was used to study corrosion mechanisms, while corrosion rate measurements were studied with the PR technique. Plates of Al203 blasted, soda blasted and conversion coated 2219 Al were coated with Deft primer and the corrosion rates studied with the EIS technique. Results from all of these studies are presented.

  3. Biorefinery: Toward an industrial metabolism.

    PubMed

    Octave, Stéphane; Thomas, Daniel

    2009-06-01

    Fossil fuel reserves are running out, global warming is becoming a reality, waste recycling is becoming ever more costly and problematic, and unrelenting population growth will require more and more energy and consumer products. There is now an alternative to the 100% oil economy; it is a renewable resource based on agroresources by using the whole plant. Production and development of these new products are based on biorefinery concept. Each constituent of the plant can be extracted and functionalized in order to produce non-food and food fractions, intermediate agro-industrial products and synthons. Three major industrial domains can be concerned: molecules, materials and energy. Molecules can be used as solvent surfactants or chemical intermediates in substitution of petrol derivatives. Fibers can be valorized in materials like composites. Sugars and oils are currently used to produce biofuels like bioethanol or biodiesel, but second-generation biofuels will use lignocellulosic biomass as raw material. Lipids can be used to produce a large diversity of products like solvent, lubricants, pastes or surfactants. Industrial biorefinery will be linked to the creation of new processes based on the twelve principles of green chemistry (clean processes, atom economy, renewable feedstocks...). Biotechnology, especially white biotechnology, will take a major part into these new processes with biotransformations (enzymology, micro-organisms...) and fermentation. The substitution of oil products by biobased products will develop a new bioeconomy and new industrial processes respecting the sustainable development concept. Industrial biorefinery can be developed on the principle that any residues of one can then be exploited as raw material by others in an industrial metabolism.

  4. Industrial Electronics Curriculum Guide. Michigan Trade and Industrial Education.

    ERIC Educational Resources Information Center

    Michigan State Univ., East Lansing. Coll. of Agriculture and Natural Resources Education Inst.

    This task-based curriculum guide for industrial electronics is intended to help the teacher develop a classroom management system where students learn by doing. Introductory materials include a Dictionary of Occupational Titles job code and title sheet, a career ladder, a matrix relating duty/task numbers to job titles, and a task list. Each task…

  5. Industrial Electricity: Motors. Oklahoma Trade and Industrial Education.

    ERIC Educational Resources Information Center

    Teague, Cash; Pewewardy, Garner

    This curriculum guide provides competency-based instructional materials for training in the field of industrial electricity. Materials are not geared to a specific grade level and may be used with secondary and postsecondary students as well as part- and full-time adult students. The guide includes three sections and ten instructional units. Each…

  6. Market trends in the projection display industry

    NASA Astrophysics Data System (ADS)

    Castellano, Joseph A.

    1999-05-01

    The projection display industry has gown rapidly over the past few year. This growth has been mainly sparked by the impact of compact units that use either liquid crystal displays or the digital light processing system developed by Texas Instruments. These units have created a large market in the multi-media business presentation segment. With the continued development of improved multi-media software, new light modulation systems, and the expanded use of 'electronic presentations', the market for projector swill continue to grow at a significant rate during the next five years. The overall worldwide unit consumption of projection information displays of al types and for all applications, including home television, topped 1.8 million units in 1998; this represented a market of 7.2 million dollars. The market is forecast to grow to 4 million units valued at 11.7 billion dollars in 2004. THe various application segments of the market and the relative sizes of the segment by the major technologies are presented in this paper.

  7. Consolidation of Al2O3/Al Nanocomposite Powder by Cold Spray

    NASA Astrophysics Data System (ADS)

    Poirier, Dominique; Legoux, Jean-Gabriel; Drew, Robin A. L.; Gauvin, Raynald

    2011-01-01

    While the improvement in mechanical properties of nanocomposites makes them attractive materials for structural applications, their processing still presents significant challenges. In this article, cold spray was used to consolidate milled Al and Al2O3/Al nanocomposite powders as well as the initial unmilled and unreinforced Al powder. The microstructure and nanohardness of the feedstock powders as well as those of the resulting coatings were compared. The results show that the large increase in hardness of the Al powder after mechanical milling is preserved after cold spraying. Good quality coating with low porosity is obtained from milled Al. However, the addition of Al2O3 to the Al powder during milling decreases the powder and coating nanohardness. This lower hardness is attributed to non-optimized milling parameters leading to cracked particles with insufficient Al2O3 embedding in Al. The coating produced from the milled Al2O3/Al mixture also showed lower particle cohesion and higher amount of porosity.

  8. The Microcalorimeter for Industrial Applications

    PubMed Central

    Redfern, Del; Nicolosi, Joe; Höhne, Jens; Weiland, Rainer; Simmnacher, Birgit; Hollerich, Christian

    2002-01-01

    To achieve the dramatic increases in x-ray spectral resolution (<20 eV at 1.5k eV) desired by market segments such as the semiconductor industry, NIST developed a transition-edge sensor (TES) microcalorimeter. To bring this exciting, yet demanding, new technology to the industrial users, certain criteria must be addressed. Aspects of resolution, cooling and hold time, count rates as well as vibrations are considered. Data is presented to the present efforts to handle these issues as well as discussing development plans for the future. PMID:27446756

  9. The chemical industry, by country

    SciTech Connect

    Not Available

    1994-05-01

    As part of its ACHEMA coverage, Hydrocarbon Processing contacted executives of petrochemical/chemical industry trade associations in 11 countries, seeking views of on the state of the industry. These reports thus provide an added dimension to feature articles in this issue that focus on petrochemical/chemical-product supply/demand trends, economic forecasts, etc. The nations represented here were chosen for commentary because collectively they contain most of the world's petrochemical capacity. Space limitations prohibit the publishing of commentaries from all countries that have petrochemical/chemical capacity. The countries are: Belgium, China, France, Germany, India, Italy, Japan, Korea, The Netherlands, United Kingdom, and the United States.

  10. Natural photonics for industrial inspiration.

    PubMed

    Parker, Andrew R

    2009-05-13

    There are two considerations for optical biomimetics: the diversity of submicrometre architectures found in the natural world, and the industrial manufacture of these. A review exists on the latter subject, where current engineering methods are considered along with those of the natural cells. Here, on the other hand, I will provide a modern review of the different categories of reflectors and antireflectors found in animals, including their optical characterization. The purpose of this is to inspire designers within the $2 billion annual optics industry.

  11. The industrialization of American psychiatry.

    PubMed

    Bittker, T E

    1985-02-01

    Physician surpluses and escalating medical care costs have fostered an alliance among government, corporate America, and health insurers that has inspired medicine's industrialization. These same forces will transform psychiatry into an industry where prospective payment, automation, salaried employment, and central control of clinical activities threaten to become the dominant form of medical practice. Emerging trends suggest that both patients and health professionals will gravitate to various forms of alternative provider organizations in an effort to shield themselves from the economic uncertainties of seeking and providing care. The chronically mentally ill and others requiring extensive treatment risk exclusion from this new system, where cost consciousness may supplant compassion.

  12. Industrial Biotechnology: Discovery to Delivery

    NASA Astrophysics Data System (ADS)

    Chotani, Gopal K.; Dodge, Timothy C.; Gaertner, Alfred L.; Arbige, Michael V.

    Fermentation products have penetrated almost every sector of our daily lives. They are used in ethical and generic drugs, clinical and home diagnostics, defense products, nutritional supplements, personal care products, food and animal feed ingredients, cleaning and textile processing, and in industrial applications such as fuel ethanol production. Even before knowing about the existence of microorganisms, for thousands of years ancient people routinely used them for making cheese, soy sauces, yogurt, and bread. Although humans have used fermentation as the method of choice for manufacturing for a long time, it is only now being recognized for its potential towards sustainable industrial development.

  13. Effect of Nano-Al2O3 on the Toxicity and Oxidative Stress of Copper towards Scenedesmus obliquus

    PubMed Central

    Li, Xiaomin; Zhou, Suyang; Fan, Wenhong

    2016-01-01

    Nano-Al2O3 has been widely used in various industries; unfortunately, it can be released into the aquatic environment. Although nano-Al2O3 is believed to be of low toxicity, it can interact with other pollutants in water, such as heavy metals. However, the interactions between nano-Al2O3 and heavy metals as well as the effect of nano-Al2O3 on the toxicity of the metals have been rarely investigated. The current study investigated copper toxicity in the presence of nano-Al2O3 towards Scenedesmus obliquus. Superoxide dismutase activity and concentration of glutathione and malondialdehyde in cells were determined in order to quantify oxidative stress in this study. Results showed that the presence of nano-Al2O3 reduced the toxicity of Cu towards S. obliquus. The existence of nano-Al2O3 decreased the growth inhibition of S. obliquus. The accumulation of copper and the level of oxidative stress in algae were reduced in the presence of nano-Al2O3. Furthermore, lower copper accumulation was the main factor that mitigated copper toxicity with the addition of nano-Al2O3. The decreased copper uptake could be attributed to the adsorption of copper onto nanoparticles and the subsequent decrease of available copper in water. PMID:27294942

  14. Estimating customer electricity savings from projects installed by the U.S. ESCO industry

    SciTech Connect

    Carvallo, Juan Pablo; Larsen, Peter H.; Goldman, Charles A.

    2014-11-25

    The U.S. energy service company (ESCO) industry has a well-established track record of delivering substantial energy and dollar savings in the public and institutional facilities sector, typically through the use of energy savings performance contracts (ESPC) (Larsen et al. 2012; Goldman et al. 2005; Hopper et al. 2005, Stuart et al. 2013). This ~$6.4 billion industry, which is expected to grow significantly over the next five years, may play an important role in achieving demand-side energy efficiency under local/state/federal environmental policy goals. To date, there has been little or no research in the public domain to estimate electricity savings for the entire U.S. ESCO industry. Estimating these savings levels is a foundational step in order to determine total avoided greenhouse gas (GHG) emissions from demand-side energy efficiency measures installed by U.S. ESCOs. We introduce a method to estimate the total amount of electricity saved by projects implemented by the U.S. ESCO industry using the Lawrence Berkeley National Laboratory (LBNL) /National Association of Energy Service Companies (NAESCO) database of projects and LBNL’s biennial industry survey. We report two metrics: incremental electricity savings and savings from ESCO projects that are active in a given year (e.g., 2012). Overall, we estimate that in 2012 active U.S. ESCO industry projects generated about 34 TWh of electricity savings—15 TWh of these electricity savings were for MUSH market customers who did not rely on utility customer-funded energy efficiency programs (see Figure 1). This analysis shows that almost two-thirds of 2012 electricity savings in municipal, local and state government facilities, universities/colleges, K-12 schools, and healthcare facilities (i.e., the so-called “MUSH” market) were not supported by a utility customer-funded energy efficiency program.

  15. Women in the Hotel and Catering Industry.

    ERIC Educational Resources Information Center

    Hotel and Catering Training Board, Wembley (England).

    A study of the employment of women in the hotel and catering industry indicated that the industry employs nearly 17 percent of the entire paid female work force in the United Kingdom. Women constitute 75 percent of the industry's work force, and 47 percent of its managers are women. Women's position in the industry is characterized by their…

  16. 49 CFR 8.31 - Industrial security.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 1 2010-10-01 2010-10-01 false Industrial security. 8.31 Section 8.31.../ACCESS Access to Information § 8.31 Industrial security. (a) Background. The National Industrial Security... industrial security services for the Department of Transportation. Regulations prescribed by the Secretary...

  17. 49 CFR 8.31 - Industrial security.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 1 2014-10-01 2014-10-01 false Industrial security. 8.31 Section 8.31.../ACCESS Access to Information § 8.31 Industrial security. (a) Background. The National Industrial Security... industrial security services for the Department of Transportation. Regulations prescribed by the Secretary...

  18. 49 CFR 8.31 - Industrial security.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 1 2013-10-01 2013-10-01 false Industrial security. 8.31 Section 8.31.../ACCESS Access to Information § 8.31 Industrial security. (a) Background. The National Industrial Security... industrial security services for the Department of Transportation. Regulations prescribed by the Secretary...

  19. 49 CFR 8.31 - Industrial security.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 1 2012-10-01 2012-10-01 false Industrial security. 8.31 Section 8.31.../ACCESS Access to Information § 8.31 Industrial security. (a) Background. The National Industrial Security... industrial security services for the Department of Transportation. Regulations prescribed by the Secretary...

  20. 49 CFR 173.411 - Industrial packagings.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... record retention applicable to Industrial Packaging Type 1 (IP-1), Industrial Packaging Type 2 (IP-2), and Industrial Packaging Type 3 (IP-3). (b) Industrial packaging certification and tests. (1) Each IP-1 must meet the general design requirements prescribed in § 173.410. (2) Each IP-2 must meet...

  1. Purdue Program Enhances Academe/Industry Ties.

    ERIC Educational Resources Information Center

    Worthy, Ward

    1985-01-01

    The Industrial Associates Program (IAP) at Purdue University is a formal organization to coordinate department-industry interactions. Philosophy, features, and projects of IAP are discussed. Indicates that a new effort will aim at setting up a sort of "Industrial Extension Service" (analogous to agricultural programs) to help industries solve…

  2. 7 CFR 1215.8 - Industry information.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 10 2013-01-01 2013-01-01 false Industry information. 1215.8 Section 1215.8... Industry information. Industry information means information and programs that will lead to the development of new markets, new marketing strategies, or increased efficiency for the popcorn industry,...

  3. 7 CFR 1260.125 - Industry information.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 10 2011-01-01 2011-01-01 false Industry information. 1260.125 Section 1260.125... Promotion and Research Order Definitions § 1260.125 Industry information. Industry information means... efficiency, and activities to enhance the image of the cattle industry....

  4. 7 CFR 1260.125 - Industry information.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 10 2013-01-01 2013-01-01 false Industry information. 1260.125 Section 1260.125... Promotion and Research Order Definitions § 1260.125 Industry information. Industry information means... efficiency, and activities to enhance the image of the cattle industry....

  5. 7 CFR 1260.125 - Industry information.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 10 2014-01-01 2014-01-01 false Industry information. 1260.125 Section 1260.125... Promotion and Research Order Definitions § 1260.125 Industry information. Industry information means... efficiency, and activities to enhance the image of the cattle industry....

  6. 7 CFR 1209.9 - Industry information.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 10 2013-01-01 2013-01-01 false Industry information. 1209.9 Section 1209.9... Definitions § 1209.9 Industry information. Industry information means information and programs that will lead... enhance the image of the mushroom industry....

  7. 7 CFR 1260.125 - Industry information.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 10 2012-01-01 2012-01-01 false Industry information. 1260.125 Section 1260.125... Promotion and Research Order Definitions § 1260.125 Industry information. Industry information means... efficiency, and activities to enhance the image of the cattle industry....

  8. 7 CFR 1215.8 - Industry information.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 10 2012-01-01 2012-01-01 false Industry information. 1215.8 Section 1215.8... Industry information. Industry information means information and programs that will lead to the development of new markets, new marketing strategies, or increased efficiency for the popcorn industry,...

  9. 7 CFR 1215.8 - Industry information.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 10 2011-01-01 2011-01-01 false Industry information. 1215.8 Section 1215.8... Industry information. Industry information means information and programs that will lead to the development of new markets, new marketing strategies, or increased efficiency for the popcorn industry,...

  10. 7 CFR 1209.9 - Industry information.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 10 2011-01-01 2011-01-01 false Industry information. 1209.9 Section 1209.9... Definitions § 1209.9 Industry information. Industry information means information and programs that will lead... enhance the image of the mushroom industry....

  11. 7 CFR 1215.8 - Industry information.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 10 2014-01-01 2014-01-01 false Industry information. 1215.8 Section 1215.8... Industry information. Industry information means information and programs that will lead to the development of new markets, new marketing strategies, or increased efficiency for the popcorn industry,...

  12. 7 CFR 1209.9 - Industry information.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 10 2012-01-01 2012-01-01 false Industry information. 1209.9 Section 1209.9... Definitions § 1209.9 Industry information. Industry information means information and programs that will lead... enhance the image of the mushroom industry....

  13. 7 CFR 1209.9 - Industry information.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 10 2014-01-01 2014-01-01 false Industry information. 1209.9 Section 1209.9... Definitions § 1209.9 Industry information. Industry information means information and programs that will lead... enhance the image of the mushroom industry....

  14. Al2O3-based nanofluids: a review

    NASA Astrophysics Data System (ADS)

    Sridhara, Veeranna; Satapathy, Lakshmi Narayan

    2011-07-01

    Ultrahigh performance cooling is one of the important needs of many industries. However, low thermal conductivity is a primary limitation in developing energy-efficient heat transfer fluids that are required for cooling purposes. Nanofluids are engineered by suspending nanoparticles with average sizes below 100 nm in heat transfer fluids such as water, oil, diesel, ethylene glycol, etc. Innovative heat transfer fluids are produced by suspending metallic or nonmetallic nanometer-sized solid particles. Experiments have shown that nanofluids have substantial higher thermal conductivities compared to the base fluids. These suspended nanoparticles can change the transport and thermal properties of the base fluid. As can be seen from the literature, extensive research has been carried out in alumina-water and CuO-water systems besides few reports in Cu-water-, TiO2-, zirconia-, diamond-, SiC-, Fe3O4-, Ag-, Au-, and CNT-based systems. The aim of this review is to summarize recent developments in research on the stability of nanofluids, enhancement of thermal conductivities, viscosity, and heat transfer characteristics of alumina (Al2O3)-based nanofluids. The Al2O3 nanoparticles varied in the range of 13 to 302 nm to prepare nanofluids, and the observed enhancement in the thermal conductivity is 2% to 36%.

  15. Cu-Al-Ni-SMA-Based High-Damping Composites

    NASA Astrophysics Data System (ADS)

    López, Gabriel A.; Barrado, Mariano; San Juan, Jose; Nó, María Luisa

    2009-08-01

    Recently, absorption of vibration energy by mechanical damping has attracted much attention in several fields such as vibration reduction in aircraft and automotive industries, nanoscale vibration isolations in high-precision electronics, building protection in civil engineering, etc. Typically, the most used high-damping materials are based on polymers due to their viscoelastic behavior. However, polymeric materials usually show a low elastic modulus and are not stable at relatively low temperatures (≈323 K). Therefore, alternative materials for damping applications are needed. In particular, shape memory alloys (SMAs), which intrinsically present high-damping capacity thanks to the dissipative hysteretic movement of interfaces under external stresses, are very good candidates for high-damping applications. A completely new approach was applied to produce high-damping composites with relatively high stiffness. Cu-Al-Ni shape memory alloy powders were embedded with metallic matrices of pure In, a In-10wt.%Sn alloy and In-Sn eutectic alloy. The production methodology is described. The composite microstructures and damping properties were characterized. A good particle distribution of the Cu-Al-Ni particles in the matrices was observed. The composites exhibit very high damping capacities in relatively wide temperature ranges. The methodology introduced provides versatility to control the temperature of maximum damping by adjusting the shape memory alloy composition.

  16. Al2O3-based nanofluids: a review

    PubMed Central

    2011-01-01

    Ultrahigh performance cooling is one of the important needs of many industries. However, low thermal conductivity is a primary limitation in developing energy-efficient heat transfer fluids that are required for cooling purposes. Nanofluids are engineered by suspending nanoparticles with average sizes below 100 nm in heat transfer fluids such as water, oil, diesel, ethylene glycol, etc. Innovative heat transfer fluids are produced by suspending metallic or nonmetallic nanometer-sized solid particles. Experiments have shown that nanofluids have substantial higher thermal conductivities compared to the base fluids. These suspended nanoparticles can change the transport and thermal properties of the base fluid. As can be seen from the literature, extensive research has been carried out in alumina-water and CuO-water systems besides few reports in Cu-water-, TiO2-, zirconia-, diamond-, SiC-, Fe3O4-, Ag-, Au-, and CNT-based systems. The aim of this review is to summarize recent developments in research on the stability of nanofluids, enhancement of thermal conductivities, viscosity, and heat transfer characteristics of alumina (Al2O3)-based nanofluids. The Al2O3 nanoparticles varied in the range of 13 to 302 nm to prepare nanofluids, and the observed enhancement in the thermal conductivity is 2% to 36%. PMID:21762528

  17. 76 FR 10471 - Tart Cherries Grown in the States of Michigan, et al.; Final Free and Restricted Percentages for...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-02-25

    ... Marketing Service 7 CFR Part 930 Tart Cherries Grown in the States of Michigan, et al.; Final Free and... strengthen market conditions. The percentages were recommended by the Cherry Industry Administrative Board... handling of tart cherries grown in the States of Michigan, New York, Pennsylvania, Oregon, Utah,...

  18. 77 FR 12748 - Tart Cherries Grown in the States of Michigan, et al.; Final Free and Restricted Percentages for...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2012-03-02

    ... Michigan, et al.; Final Free and Restricted Percentages for the 2011-12 Crop Year for Tart Cherries AGENCY... tart cherries grown in the states of Michigan, New York, Pennsylvania, Oregon, Utah, Washington, and Wisconsin (order). The order is administered locally by the Cherry Industry Administrative Board...

  19. AlOx barrier growth in magnetic tunnel junctions for sensor applications

    NASA Astrophysics Data System (ADS)

    Knudde, S.; Farinha, G.; Leitao, D. C.; Ferreira, R.; Cardoso, S.; Freitas, P. P.

    2016-08-01

    Magnetic tunnel junction (MTJ) research has been focused on MgO-based crystalline structures due to high tunnel magnetoresistance (TMR), despite requiring a more severe process control than previous generations of MTJ stacks based on amorphous barriers (e.g. AlOx). In this work, we study the electrical transport properties in AlOx barriers in MTJ sensors fabricated using Ion beam sputtering and remote plasma oxidation. Amorphous barriers were prepared from oxidation of thin Al films, deposited in single step barrier (SSB-Al 1 nm/oxidation) or double step barrier (DSB-Al 0.5 nm/oxidation/Al 0.5 nm/oxidation) structures. We show tunable resistance-area products (RxA) ranging from ≈ 10 Ω μ m2 (suited for nano devices) up to ≈ 100 k Ω μ m2 (suited for large area sensors) with TMR above 30%. For all geometries studied, the structures have a coercivity free linear response and require none or one annealing step. This makes them very competitive for all industrial applications where the TMR level is not the dominant specification to meet.

  20. Fabrication and characterization of stable superhydrophobic surface with good friction-reducing performance on Al foil

    NASA Astrophysics Data System (ADS)

    Li, Peipei; Chen, Xinhua; Yang, Guangbin; Yu, Laigui; Zhang, Pingyu

    2014-05-01

    A lotus-leaf-like hierarchical structure with superhydrophobicity was created on Al foil by a facile three-step solution-immersion method involving etching in hydrochloric acid solution and immersing in hot water as well as surface-modification by stearic acid (denoted as STA). As-prepared etched-immersed Al/STA rough surface was characterized by means of scanning electron microscopy and X-ray photoelectron spectroscopy. Moreover, the water contact angles and water sliding angles of as-prepared etched-immersed Al/STA rough surface were measured, and the friction-reducing performance and self-cleaning ability of the as-prepared surface were also evaluated. Results indicate that the etched-immersed Al/STA rough surface consists of interconnected convex-concave micro-structure and uniformly distributed nano-sheets. Besides, it exhibits stable superhydrophobicity and good friction-reducing ability. Namely, it has a contact angle of water as high as 164.2° and a water sliding angle lower than 5°, while it retains good friction-reducing ability during extended sliding and possesses good self-cleaning ability as well. This demonstrates that the etched-immersed Al/STA rough surface may favor the applications of Al and its alloys in various industrial fields.