Science.gov

Sample records for alignment maintenance system

  1. Segment Alignment Maintenance System for the Hobby-Eberly Telescope

    NASA Technical Reports Server (NTRS)

    Rakoczy, John; Burdine, Robert (Technical Monitor)

    2001-01-01

    NASA's Marshall Space Flight Center, in collaboration with Blue Line Engineering of Colorado Springs, Colorado, is developing a Segment Alignment Maintenance System (SAMS) for McDonald Observatory's Hobby-Eberly Telescope (HET). The SAMS shall sense motions of the 91 primary mirror segments and send corrections to HET's primary mirror controller as the mirror segments misalign due to thermo -elastic deformations of the mirror support structure. The SAMS consists of inductive edge sensors. All measurements are sent to the SAMS computer where mirror motion corrections are calculated. In October 2000, a prototype SAMS was installed on a seven-segment cluster of the HET. Subsequent testing has shown that the SAMS concept and architecture are a viable practical approach to maintaining HET's primary mirror figure, or the figure of any large segmented telescope. This paper gives a functional description of the SAMS sub-array components and presents test data to characterize the performance of the subarray SAMS.

  2. Primary Mirror Figure Maintenance of the Hobby-Eberly Telescope using the Segment Alignment Maintenance System

    NASA Technical Reports Server (NTRS)

    Rakoczy, John; Hall, Drew; Howard, Ricky; Ly, William; Weir, John; Montgomery, Edward; Brantley, Lott W. (Technical Monitor)

    2002-01-01

    The Segment Alignment Maintenance System (SAMs) was installed on McDonald Observatory's Hobby-Eberly Telescope (HET) in August 2001. The SAMs became fully operational in October 2001. The SAMs uses a system of 480 inductive edge sensors to correct misalignments of the HET's 91 primary mirror segments when the segments are perturbed from their aligned reference positions. A special observer estimated and corrects for the global radius of curvature (GroC) mode, a mode unobservable by the edge sensors. The SAMs edge sensor system and (GroC) estimator are able to maintain HET's primary figure for much longer durations than previously had been observed. Telescope image quality has improved, and the amount of overhead time required from primary mirror alignment has been reduced. This paper gives a functional description of the SAMs control system and presents performance verification data. This paper also describes how the SAMs has improved the operational efficiency of the HET.

  3. Drive alignment pays maintenance dividends

    SciTech Connect

    Fedder, R.

    2008-12-15

    Proper alignment of the motor and gear drive on conveying and processing equipment will result in longer bearing and coupling life, along with lower maintenance costs. Selecting an alignment free drive package instead of a traditional foot mounted drive and motor is a major advancement toward these goals. 4 photos.

  4. Software development for the Hobby-Eberly Telescope's Segment Alignment Maintenance System using LabVIEW

    NASA Astrophysics Data System (ADS)

    Hall, Drew; Ly, William; Howard, Richard T.; Weir, John T.; Rakoczy, John M.

    2002-12-01

    The software development for an upgrade to the Hobby-Eberly Telescope (HET) was done in LabVIEW. In order to improve the performance of the HET at the McDonald Observatory, a closed-loop system had to be implemented to keep the mirror segments aligned during periods of observation. The control system, called the Segment Alignment Maintenance System (SAMS), utilized inductive sensors to measure the relative motions of the mirror segments. Software was developed in LabVIEW to tie the sensors, operator interface, and mirror-control motors together. Developing the software in LabVIEW allowed the system to be flexible, understandable, and able to be modified by the end users. Since LabVIEW is built using block diagrams, the software naturally followed the designed control system's block and flow diagrams, and individual software blocks could be easily verified. LabVIEW's many built-in display routines allowed easy visualization of diagnostic and health-monitoring data during testing. Also, since LabVIEW is a multi-platform software package, different programmers could develop the code remotely on various types of machines. LabVIEW's ease of use facilitated rapid prototyping and field-testing. There were some unanticipated difficulties in the software development, but the use of LabVIEW as the software "language" for the development of SAMS contributed to the overall success of the project.

  5. Software Development for the Hobby-Eberly Telescope's Segment Alignment Maintenance System using LABView

    NASA Technical Reports Server (NTRS)

    Hall, Drew P.; Ly, William; Howard, Richard T.; Weir, John; Rakoczy, John; Roe, Fred (Technical Monitor)

    2002-01-01

    The software development for an upgrade to the Hobby-Eberly Telescope (HET) was done in LABView. In order to improve the performance of the HET at the McDonald Observatory, a closed-loop system had to be implemented to keep the mirror segments aligned during periods of observation. The control system, called the Segment Alignment Maintenance System (SAMs), utilized inductive sensors to measure the relative motions of the mirror segments. Software was developed in LABView to tie the sensors, operator interface, and mirror-control motors together. Developing the software in LABView allowed the system to be flexible, understandable, and able to be modified by the end users. Since LABView is built using block diagrams, the software naturally followed the designed control system's block and flow diagrams, and individual software blocks could be easily verified. LABView's many built-in display routines allowed easy visualization of diagnostic and health-monitoring data during testing. Also, since LABView is a multi-platform software package, different programmers could develop the code remotely on various types of machines. LABView s ease of use facilitated rapid prototyping and field testing. There were some unanticipated difficulties in the software development, but the use of LABView as the software "language" for the development of SAMs contributed to the overall success of the project.

  6. Segment alignment control system

    NASA Technical Reports Server (NTRS)

    Aubrun, JEAN-N.; Lorell, Ken R.

    1988-01-01

    The segmented primary mirror for the LDR will require a special segment alignment control system to precisely control the orientation of each of the segments so that the resulting composite reflector behaves like a monolith. The W.M. Keck Ten Meter Telescope will utilize a primary mirror made up of 36 actively controlled segments. Thus the primary mirror and its segment alignment control system are directly analogous to the LDR. The problems of controlling the segments in the face of disturbances and control/structures interaction, as analyzed for the TMT, are virtually identical to those for the LDR. The two systems are briefly compared.

  7. Demonstration of a Segment Alignment Maintenance System on a Seven-Segment Sub-Array of the Hobby-Eberly Telescope

    NASA Technical Reports Server (NTRS)

    Rakoczy, John; Whitaker, Ann F. (Technical Monitor)

    2001-01-01

    NASA's Marshall Space Flight Center, in collaboration with Blue Line Engineering of Colorado Springs, Colorado, is developing a Segment Alignment Maintenance System (SAMS) for McDonald Observatory's Hobby-Eberly Telescope (HET). The SAMS shall sense motions of the 91 primary mirror segments and send corrections to HET's primary mirror controller as the mirror segments misalign due to thermo-elastic deformations of the mirror support structure. The SAMS consists of inductive edge sensors supplemented by inclinometers for global radius of curvature sensing. All measurements are sent to the SAMS computer where mirror motion corrections are calculated. In October 2000, a prototype SAMS was installed on a seven-segment cluster of the HET. Subsequent testing has shown that the SAMS concept and architecture are a viable practical approach to maintaining HET's primary mirror figure, or the figure of any large segmented telescope. This paper gives a functional description of the SAMS sub-array components and presents test data to characterize the performance of the sub-array SAMS.

  8. Alignment system for encoders

    NASA Technical Reports Server (NTRS)

    Villani, Daniel D. (Inventor)

    1988-01-01

    An improved encoder alignment system is disclosed which provides an indication of the extent of misalignment and a measure of the rate at which the misalignment may be changing. The invention is adapted for use with a conventional encoder which provides a digital coarse word having at least significant bit and a digital fine word having a least significant bit and a most significant bit. The invention generates the exclusive or of the least significant bit of the coarse digital signal and the least significant bit of the fine digital signal to provide a first signal. The invention then generates the exclusive or of the first signal and the complement of the most significant bit of the fine digital signal to provide an output signal which represents the misalignment of the encoder.

  9. Maintenance of Automated Library Systems.

    ERIC Educational Resources Information Center

    Epstein, Susan Baerg

    1983-01-01

    Discussion of the maintenance of both the software and hardware in an automated library system highlights maintenance by the vendor, contracts and costs, the maintenance log, downtime, and planning for trouble. (EJS)

  10. Improved docking alignment system

    NASA Technical Reports Server (NTRS)

    Monford, Leo G. (Inventor)

    1988-01-01

    Improved techniques are provided for the alignment of two objects. The present invention is particularly suited for 3-D translation and 3-D rotational alignment of objects in outer space. A camera is affixed to one object, such as a remote manipulator arm of the spacecraft, while the planar reflective surface is affixed to the other object, such as a grapple fixture. A monitor displays in real-time images from the camera such that the monitor displays both the reflected image of the camera and visible marking on the planar reflective surface when the objects are in proper alignment. The monitor may thus be viewed by the operator and the arm manipulated so that the reflective surface is perpendicular to the optical axis of the camera, the roll of the reflective surface is at a selected angle with respect to the camera, and the camera is spaced a pre-selected distance from the reflective surface.

  11. Well-pump alignment system

    DOEpatents

    Drumheller, Douglas S.

    1998-01-01

    An improved well-pump for geothermal wells, an alignment system for a well-pump, and to a method for aligning a rotor and stator within a well-pump, wherein the well-pump has a whistle assembly formed at a bottom portion thereof, such that variations in the frequency of the whistle, indicating misalignment, may be monitored during pumping.

  12. Terminal automation system maintenance

    SciTech Connect

    Coffelt, D.; Hewitt, J.

    1997-01-01

    Nothing has improved petroleum product loading in recent years more than terminal automation systems. The presence of terminal automation systems (TAS) at loading racks has increased operational efficiency and safety and enhanced their accounting and management capabilities. However, like all finite systems, they occasionally malfunction or fail. Proper servicing and maintenance can minimize this. And in the unlikely event a TAS breakdown does occur, prompt and effective troubleshooting can reduce its impact on terminal productivity. To accommodate around-the-clock loading at racks, increasingly unattended by terminal personnel, TAS maintenance, servicing and troubleshooting has become increasingly demanding. It has also become increasingly important. After 15 years of trial and error at petroleum and petrochemical storage and transfer terminals, a number of successful troubleshooting programs have been developed. These include 24-hour {open_quotes}help hotlines,{close_quotes} internal (terminal company) and external (supplier) support staff, and {open_quotes}layered{close_quotes} support. These programs are described.

  13. Docking alignment system

    NASA Technical Reports Server (NTRS)

    Monford, Leo G. (Inventor)

    1990-01-01

    Improved techniques are provided for alignment of two objects. The present invention is particularly suited for three-dimensional translation and three-dimensional rotational alignment of objects in outer space. A camera 18 is fixedly mounted to one object, such as a remote manipulator arm 10 of the spacecraft, while the planar reflective surface 30 is fixed to the other object, such as a grapple fixture 20. A monitor 50 displays in real-time images from the camera, such that the monitor displays both the reflected image of the camera and visible markings on the planar reflective surface when the objects are in proper alignment. The monitor may thus be viewed by the operator and the arm 10 manipulated so that the reflective surface is perpendicular to the optical axis of the camera, the roll of the reflective surface is at a selected angle with respect to the camera, and the camera is spaced a pre-selected distance from the reflective surface.

  14. Remote maintenance monitoring system

    NASA Technical Reports Server (NTRS)

    Simpkins, Lorenz G. (Inventor); Owens, Richard C. (Inventor); Rochette, Donn A. (Inventor)

    1992-01-01

    A remote maintenance monitoring system retrofits to a given hardware device with a sensor implant which gathers and captures failure data from the hardware device, without interfering with its operation. Failure data is continuously obtained from predetermined critical points within the hardware device, and is analyzed with a diagnostic expert system, which isolates failure origin to a particular component within the hardware device. For example, monitoring of a computer-based device may include monitoring of parity error data therefrom, as well as monitoring power supply fluctuations therein, so that parity error and power supply anomaly data may be used to trace the failure origin to a particular plane or power supply within the computer-based device. A plurality of sensor implants may be rerofit to corresponding plural devices comprising a distributed large-scale system. Transparent interface of the sensors to the devices precludes operative interference with the distributed network. Retrofit capability of the sensors permits monitoring of even older devices having no built-in testing technology. Continuous real time monitoring of a distributed network of such devices, coupled with diagnostic expert system analysis thereof, permits capture and analysis of even intermittent failures, thereby facilitating maintenance of the monitored large-scale system.

  15. Well-pump alignment system

    DOEpatents

    Drumheller, D.S.

    1998-10-20

    An improved well-pump for geothermal wells, an alignment system for a well-pump, and to a method for aligning a rotor and stator within a well-pump are disclosed, wherein the well-pump has a whistle assembly formed at a bottom portion thereof, such that variations in the frequency of the whistle, indicating misalignment, may be monitored during pumping. 6 figs.

  16. Space Mirror Alignment System

    NASA Technical Reports Server (NTRS)

    Jau, Bruno M.; McKinney, Colin; Smythe, Robert F.; Palmer, Dean L.

    2011-01-01

    An optical alignment mirror mechanism (AMM) has been developed with angular positioning accuracy of +/-0.2 arcsec. This requires the mirror s linear positioning actuators to have positioning resolutions of +/-112 nm to enable the mirror to meet the angular tip/tilt accuracy requirement. Demonstrated capabilities are 0.1 arc-sec angular mirror positioning accuracy, which translates into linear positioning resolutions at the actuator of 50 nm. The mechanism consists of a structure with sets of cross-directional flexures that enable the mirror s tip and tilt motion, a mirror with its kinematic mount, and two linear actuators. An actuator comprises a brushless DC motor, a linear ball screw, and a piezoelectric brake that holds the mirror s position while the unit is unpowered. An interferometric linear position sensor senses the actuator s position. The AMMs were developed for an Astrometric Beam Combiner (ABC) optical bench, which is part of an interferometer development. Custom electronics were also developed to accommodate the presence of multiple AMMs within the ABC and provide a compact, all-in-one solution to power and control the AMMs.

  17. DCSP hardware maintenance system

    SciTech Connect

    Pazmino, M.

    1995-11-01

    This paper discusses the necessary changes to be implemented on the hardware side of the DCSP database. DCSP is currently tracking hardware maintenance costs in six separate databases. The goal is to develop a system that combines all data and works off a single database. Some of the tasks that will be discussed in this paper include adding the capability for report generation, creating a help package and preparing a users guide, testing the executable file, and populating the new database with data taken from the old database. A brief description of the basic process used in developing the system will also be discussed. Conclusions about the future of the database and the delivery of the final product are then addressed, based on research and the desired use of the system.

  18. Cell Maintenance Systems

    NASA Technical Reports Server (NTRS)

    Morrison, D. R.

    1985-01-01

    Living human cells require attachment to a suitable surface and special culture conditions in order to grow. These requirements are modified and amplified when cells are taken into a weightless environment. Special handling and maintenance systems are required for routine laboratory procedures conducted in the Orbiter and in the Spacelab. Methods were developed to maintain cells in special incubators designed for the Orbiter middeck, however, electrophoresis and other experiments require cells to be harvested off of the culture substrate before they can be processed or used. The cell transport assembly (CTA) was flown on STS-8, and results show that improvements are required to maintain adequate numbers of cells in this device longer than 48 hours. The life sciences middeck centrifuge probably can be used, but modifications will be required to transfer cells from the CTA and keep the cells sterile. Automated systems such as the Skylab SO-15 flight hardware and crew operated systems are being evaluated for use on the Space Shuttle, Spacelab, and Space Station research modules.

  19. Global Alignment System for Large Genomic Sequencing

    2002-03-01

    AVID is a global alignment system tailored for the alignment of large genomic sequences up to megabases in length. Features include the possibility of one sequence being in draft form, fast alignment, robustness and accuracy. The method is an anchor based alignment using maximal matches derived from suffix trees.

  20. Antares beam-alignment-system performance

    SciTech Connect

    Appert, Q.D.; Bender, S.C.

    1983-01-01

    The beam alignment system for the 24-beam-sector Antares CO/sub 2/ fusion laser automatically aligns more than 200 optical elements. A visible-wavelength alignment technique is employed which uses a telescope/TV system to view point-light sources appropriately located down the beamline. The centroids of the light spots are determined by a video tracker, which generates error signals used by the computer control system to move appropriate mirrors in a closed-loop system. Final touch-up alignment is accomplished by projecting a CO/sub 2/ alignment laser beam through the system and sensing its position at the target location. The techniques and control algorithms employed have resulted in alignment accuracies exceeding design requirements. By employing video processing to determine the centroids of diffraction images and by averaging over multiple TV frames, we achieve alignment accuracies better than 0.1 times system diffraction limits in the presence of air turbulence.

  1. Maintenance of photovoltaic power systems

    NASA Astrophysics Data System (ADS)

    Hall, M. R.

    1984-08-01

    This publication establishes standard practices for inspection, testing, and maintenance of photovoltaic power systems at Dept. of the Navy installations. The practices and procedures are recommended to ensure reliable operation of the power systems. The manual covers photovoltaic-array, battery, voltage-regulator, inverter, and wiring subsystems. In addition, this manual provides a troubleshooting guide and self-study questions and answers.

  2. Maintenance of photovoltaic power systems

    SciTech Connect

    Hall, M.R.

    1984-08-01

    This publication establishes standard practices for inspection, testing, and maintenance of photovoltaic power systems at Department of the Navy installations. The practices and procedures are recommended to ensure reliable operation of the power systems. The manual covers photovoltaic-array, battery, voltage-regulator, inverter, and wiring subsystems. In addition, this manual provides a troubleshooting guide and self-study questions and answers.

  3. Iron production maintenance effectiveness system

    SciTech Connect

    Augstman, J.J.

    1996-12-31

    In 1989, an internal study in the Coke and Iron Maintenance Department identified the opportunities available to increase production, by decreasing unscheduled maintenance delays from 4.6%. A five year front loaded plan was developed, and presented to the company president. The plan required an initial investment of $1.4 million and a conservative break-even point was calculated to be 2.5 years. Due to budget restraints, it would have to be self-funded, i.e., generate additional production or savings, to pay for the program. The program began in 1991 at number 2 coke plant and the blast furnaces. This paper will describe the Iron Production Maintenance Effectiveness System (ME), which began with the mechanical and pipefitting trades.

  4. Alignments between galaxies, satellite systems and haloes

    NASA Astrophysics Data System (ADS)

    Shao, Shi; Cautun, Marius; Frenk, Carlos S.; Gao, Liang; Crain, Robert A.; Schaller, Matthieu; Schaye, Joop; Theuns, Tom

    2016-08-01

    The spatial distribution of the satellite populations of the Milky Way and Andromeda are puzzling in that they are nearly perpendicular to the disks of their central galaxies. To understand the origin of such configurations we study the alignment of the central galaxy, satellite system and dark matter halo in the largest of the "Evolution and Assembly of GaLaxies and their Environments" (EAGLE) simulation. We find that centrals and their satellite systems tend to be well aligned with their haloes, with a median misalignment angle of $33^{\\circ}$ in both cases. While the centrals are better aligned with the inner $10$ kpc halo, the satellite systems are better aligned with the entire halo indicating that satellites preferentially trace the outer halo. The central - satellite alignment is weak (median misalignment angle of $52^{\\circ}$) and we find that around $20\\%$ of systems have a misalignment angle larger than $78^{\\circ}$, which is the value for the Milky Way. The central - satellite alignment is a consequence of the tendency of both components to align with the dark matter halo. As a consequence, when the central is parallel to the satellite system, it also tends to be parallel to the halo. In contrast, if the central is perpendicular to the satellite system, as in the case of the Milky Way and Andromeda, then the central - halo alignment is much weaker. Dispersion-dominated (spheroidal) centrals have a stronger alignment with both their halo and their satellites than rotation-dominated (disk) centrals. We also found that the halo, the central galaxy and the satellite system tend to be aligned with the surrounding large-scale distribution of matter, with the halo being the better aligned of the three.

  5. Alignments between galaxies, satellite systems and haloes

    NASA Astrophysics Data System (ADS)

    Shao, Shi; Cautun, Marius; Frenk, Carlos S.; Gao, Liang; Crain, Robert A.; Schaller, Matthieu; Schaye, Joop; Theuns, Tom

    2016-08-01

    The spatial distribution of the satellite populations of the Milky Way and Andromeda are puzzling in that they are nearly perpendicular to the discs of their central galaxies. To understand the origin of such configurations we study the alignment of the central galaxy, satellite system and dark matter halo in the largest of the `Evolution and Assembly of GaLaxies and their Environments' (EAGLE) simulation. We find that centrals and their satellite systems tend to be well aligned with their haloes, with a median misalignment angle of 33° in both cases. While the centrals are better aligned with the inner 10 kpc halo, the satellite systems are better aligned with the entire halo indicating that satellites preferentially trace the outer halo. The central-satellite alignment is weak (median misalignment angle of 52°) and we find that around 20 per cent of systems have a misalignment angle larger than 78°, which is the value for the Milky Way. The central-satellite alignment is a consequence of the tendency of both components to align with the dark matter halo. As a consequence, when the central is parallel to the satellite system, it also tends to be parallel to the halo. In contrast, if the central is perpendicular to the satellite system, as in the case of the Milky Way and Andromeda, then the central-halo alignment is much weaker. Dispersion-dominated (spheroidal) centrals have a stronger alignment with both their halo and their satellites than rotation-dominated (disc) centrals. We also found that the halo, the central galaxy and the satellite system tend to be aligned with the surrounding large-scale distribution of matter, with the halo being the better aligned of the three.

  6. IMIS: Integrated Maintenance Information System. A maintenance information delivery concept

    NASA Technical Reports Server (NTRS)

    Vonholle, Joseph C.

    1987-01-01

    The Integrated Maintenance Information System (IMIS) will optimize the use of available manpower, enhance technical performance, improve training, and reduce the support equipment and documentation needed for deployment. It will serve as the technician's single, integrated source of all the technical information required to perform modern aircraft maintenance.

  7. Automated interferometric alignment system for paraboloidal mirrors

    DOEpatents

    Maxey, L.C.

    1993-09-28

    A method is described for a systematic method of interpreting interference fringes obtained by using a corner cube retroreflector as an alignment aid when aligning a paraboloid to a spherical wavefront. This is applicable to any general case where such alignment is required, but is specifically applicable in the case of aligning an autocollimating test using a diverging beam wavefront. In addition, the method provides information which can be systematically interpreted such that independent information about pitch, yaw and focus errors can be obtained. Thus, the system lends itself readily to automation. Finally, although the method is developed specifically for paraboloids, it can be seen to be applicable to a variety of other aspheric optics when applied in combination with a wavefront corrector that produces a wavefront which, when reflected from the correctly aligned aspheric surface will produce a collimated wavefront like that obtained from the paraboloid when it is correctly aligned to a spherical wavefront. 14 figures.

  8. Partial Automated Alignment and Integration System

    NASA Technical Reports Server (NTRS)

    Kelley, Gary Wayne (Inventor)

    2014-01-01

    The present invention is a Partial Automated Alignment and Integration System (PAAIS) used to automate the alignment and integration of space vehicle components. A PAAIS includes ground support apparatuses, a track assembly with a plurality of energy-emitting components and an energy-receiving component containing a plurality of energy-receiving surfaces. Communication components and processors allow communication and feedback through PAAIS.

  9. Automated interferometric alignment system for paraboloidal mirrors

    DOEpatents

    Maxey, L. Curtis

    1993-01-01

    A method is described for a systematic method of interpreting interference fringes obtained by using a corner cube retroreflector as an alignment aid when aigning a paraboloid to a spherical wavefront. This is applicable to any general case where such alignment is required, but is specifically applicable in the case of aligning an autocollimating test using a diverging beam wavefront. In addition, the method provides information which can be systematically interpreted such that independent information about pitch, yaw and focus errors can be obtained. Thus, the system lends itself readily to automation. Finally, although the method is developed specifically for paraboloids, it can be seen to be applicable to a variety of other aspheric optics when applied in combination with a wavefront corrector that produces a wavefront which, when reflected from the correctly aligned aspheric surface will produce a collimated wavefront like that obtained from the paraboloid when it is correctly aligned to a spherical wavefront.

  10. MAST YAG Thomson scattering upgrade alignment system

    SciTech Connect

    Figueiredo, J.; Serra, F.; Naylor, G.; Walsh, M.; Dunstan, M.; Scannell, R.

    2010-10-15

    The recent upgrade to the MAST YAG Thomson scattering while enhancing the diagnostic capabilities increased the complexity of the system. There are eight YAG lasers now operational, doubling the number from the previous setup. This means alignment between each laser individually and reference points is essential to guarantee data quality and diagnostic reliability. To address this issue an alignment system was recently installed. It mimics the beams alignment in MAST by sampling 1% of the laser beam that is sent into a telescope which demagnifies by a factor of 8. The demagnified beam is viewed with a CCD camera. By scanning the camera the profile and position of the beams in the scattering zone and in a range of several meters inside MAST can be determined. Therefore alignment is checked along the beam path without having to sample it inside the vessel. The experimental apparatus and test procedures are described.

  11. Evolution of shiva laser alignment systems

    SciTech Connect

    Boyd, R.D.

    1980-07-01

    The Shiva oscillator pulse is preamplified and divided into twenty beams. Each beam is then amplified, spatially filtered, directed, and focused onto a target a few hundred micrometers in size producing optical intensities up to 10/sup 16/W/cm/sup 2/. The laser was designed and built with three automatic alignment systems: the oscillator alignment system, which aligns each of the laser's three oscillators to a reference beamline; the chain input pointing system, which points each beam into its respective chain; and the chain output pointing, focusing and centering system which points, centers and focuses the beam onto the target. Recently the alignment of the laser's one hundred twenty spatial filter pinholes was also automated. This system uses digitized video images of back-illuminated pinholes and computer analysis to determine current positions. The offset of each current position from a desired center point is then translated into stepper motor commands and the pinhole is moved the proper distance. While motors for one pinhole are moving, the system can digitize, analyze, and send commands to other motors, allowing the system to efficiently align several pinholes in parallel.

  12. Maintenance of photovoltaic power systems. Revision 1. Maintenance manual

    SciTech Connect

    Hall, M.R.

    1985-06-01

    This publication establishes standard practices for inspection, testing, and maintenance of photovoltaic power systems at Department of the Navy installations. The practices and procedures are recommended to ensure reliable operation of the power systems. The manual covers photovoltaic-array, battery, voltage-regulator, inverter, and wiring subsystems. In addition, this manual provides a troubleshooting guide and self-study questions and answers.

  13. Smart and precise alignment of optical systems

    NASA Astrophysics Data System (ADS)

    Langehanenberg, Patrik; Heinisch, Josef; Stickler, Daniel

    2013-09-01

    For the assembly of any kind of optical systems the precise centration of every single element is of particular importance. Classically the precise alignment of optical components is based on the precise centering of all components to an external axis (usually a high-precision rotary spindle axis). Main drawback of this timeconsuming process is that it is significantly sensitive to misalignments of the reference (e.g. the housing) axis. In order to facilitate process in this contribution we present a novel alignment strategy for the TRIOPTICS OptiCentric® instrument family that directly aligns two elements with respect to each other by measuring the first element's axis and using this axis as alignment reference without the detour of considering an external reference. According to the optical design any axis in the system can be chosen as target axis. In case of the alignment to a barrel this axis is measured by using a distance sensor (e.g., the classically used dial indicator). Instead of fine alignment the obtained data is used for the calculation of its orientation within the setup. Alternatively, the axis of an optical element (single lens or group of lenses) whose orientation is measured with the standard OptiCentric MultiLens concept can be used as a reference. In the instrument's software the decentering of the adjusting element to the calculated axis is displayed in realtime and indicated by a target mark that can be used for the manual alignment. In addition, the obtained information can also be applied for active and fully automated alignment of lens assemblies with the help of motorized actuators.

  14. Robust optical alignment systems using geometric invariants

    NASA Astrophysics Data System (ADS)

    Ho, Tzung-Hsien; Rzasa, John; Milner, Stuart D.; Davis, Christopher C.

    2007-09-01

    Traditional coarse pointing, acquisition, and tracking (CPAT) systems are pre-calibrated to have the center pixel of the camera aligned to the laser pointing vector and the center pixel is manually moved to the target of interest to complete the alignment process. Such a system has previously demonstrated its capability in aligning with distant targets and the pointing accuracy is on the order of sensor resolution. However, aligning with targets at medium range where the distance between angular sensor and transceiver is not negligible is its Achilles Heel. This limitation can be resolved by imposing constraints, such as the trifocal tensor (TT), which is deduced from the geometrical dependence between cameras and transceivers. Two autonomous CPAT systems are introduced for FSO transceiver alignment in mid- and long-range scenarios. This work focuses on experimental results that validate the pointing performance for targets at different distances, backed up by the theoretical derivations. A mid-range CPAT system, applying a trifocal tensor as its geometric invariant, includes two perspective cameras as sensors to perceive target distances. The long-range CPAT system, applying linear mapping as the invariant, requires only one camera to determine the pointing angle. Calibration procedures for both systems are robust to measurement noise and the resulting system can autonomously point to a target of interest with a high accuracy, which is also on the order of sensor resolution. The results of this work are not only beneficial to the design of CPAT systems for FSO transceiver alignment, but also in new applications such as surveillance and navigation.

  15. Pupil Alignment Measuring Technique and Alignment Reference for Instruments or Optical Systems

    NASA Technical Reports Server (NTRS)

    Hagopian, John G.

    2010-01-01

    A technique was created to measure the pupil alignment of instruments in situ by measuring calibrated pupil alignment references (PARs) in instruments. The PAR can also be measured using an alignment telescope or an imaging system. PAR allows the verification of the science instrument (SI) pupil alignment at the integrated science instrument module (ISIM) level of assembly at ambient and cryogenic operating temperature. This will allow verification of the ISIM+SI alignment, and provide feedback to realign the SI if necessary.

  16. Active alignment/contact verification system

    DOEpatents

    Greenbaum, William M.

    2000-01-01

    A system involving an active (i.e. electrical) technique for the verification of: 1) close tolerance mechanical alignment between two component, and 2) electrical contact between mating through an elastomeric interface. For example, the two components may be an alumina carrier and a printed circuit board, two mating parts that are extremely small, high density parts and require alignment within a fraction of a mil, as well as a specified interface point of engagement between the parts. The system comprises pairs of conductive structures defined in the surfaces layers of the alumina carrier and the printed circuit board, for example. The first pair of conductive structures relate to item (1) above and permit alignment verification between mating parts. The second pair of conductive structures relate to item (2) above and permit verification of electrical contact between mating parts.

  17. Maintenance requirements in solar air heating systems

    SciTech Connect

    Lof, G.O.G.; Junk, J.P.

    1983-06-01

    The maintenance requirements of a well designed and constructed solar air-heating system are comparable to those of conventional, forced warm air heating systems. One of the major reasons for this low maintenance is the absence of problems associated with corrosion, freezing, boiling, and leakage often encountered in solar liquid systems. Experience shows that most problems are due to overly complex designs, control problems, faulty installation, and adjustment of the moving parts in the system. Operational histories show negligible requirements for maintenance of air collectors, pebble-bed heat-storage bins, and system ducts and connections. Good quality control in the manufacture and installation of airtight collectors, heat-storage bins, and interconnecting ductwork is essential, however. The paper includes a description of solar air-heating systems and their characteristics, an evaluation of the various maintenance requirements, and several case histories illustrating the handling of solar air system maintenance.

  18. Implementation of two-state alignment system into CXrL aligner (Poster Paper)

    NASA Astrophysics Data System (ADS)

    Chen, Guan-Jye; Bodoh, D.; Wallace, John P.; Anderson, Paul D.; Reilly, Michael T.; Nachman, Ramez; Cerrina, Franco

    1992-07-01

    We describe the implementation of the two-state alignment system into the CXrL aligner, which is developed at our Center for X-ray Lithography. The CXrL aligner is designed to expose sub 0.25 μm feature size integrated circuits. The aligner consists of a three-axes two-state alignment system for alignment error detection and a piezo based precision mechanical stage for alignment error correction. The wafer is held by a precision vacuum chuck, while the mask is held by three vacuum suction cups located around the glass ring. In the prototype, the mask to wafer relative positioning is achieved by 3 motorized stages (for gap setting) and 3 piezo-actuators (for lateral alignment). Since the optical system is designed to be located outside of the synchrotron radiation path, alignment can be performed during exposure. We present the results of the alignment system performance, such as noise equivalent displacement and alignment signal response time. An alignment signal repeatibility of much better than 3σ = 0.07μm is achieved. We also briefly describe the future evaluation of the system, such as overlay measurement of the system using verniers and SEM inspection of some specially designed patterns.

  19. Effective maintenance practices to manage system aging

    NASA Astrophysics Data System (ADS)

    Chockie, Alan; Bjorkelo, Kenneth

    A study for the Nuclear Regulatory Commission was recently undertaken to identify effective maintenance practices that could be adapted by the nuclear industry in the United States to assist in managing the aging degradation of plant systems and components. Four organizations were examined to assess the influence of maintenance programs on addressing the system and component aging degradation issues. An effective maintenance program was found to be essential to the management of system and component aging. Four key elements of an effective maintenance program that are important to an aging management were identified: (1) the selection of critical systems and components; (2) the development of an understanding of aging through the collection and analysis of equipment performance information; (3) the development of appropriate preventive and predictive maintenance tasks to manage equipment and system aging degradation; and (4) the use of feedback mechanisms to continuously improve the management of aging systems and components. These elements were found to be common to all four organizations.

  20. [Development of Hospital Equipment Maintenance Information System].

    PubMed

    Zhou, Zhixin

    2015-11-01

    Hospital equipment maintenance information system plays an important role in improving medical treatment quality and efficiency. By requirement analysis of hospital equipment maintenance, the system function diagram is drawed. According to analysis of input and output data, tables and reports in connection with equipment maintenance process, relationships between entity and attribute is found out, and E-R diagram is drawed and relational database table is established. Software development should meet actual process requirement of maintenance and have a friendly user interface and flexible operation. The software can analyze failure cause by statistical analysis. PMID:27066680

  1. Assembly and alignment of infrared refractive system

    NASA Astrophysics Data System (ADS)

    Yang, Lin; Lin, Jian-chun; Wang, Ya-jing; Chen, Fan-sheng

    2013-09-01

    Optical systems for scientific instrumentation frequently include lens or mirrors with critical mechanical requirements. Position issues of those components are inextricably bound to the efficiency of the instrument. The position referring to the lens system mainly means spacer and rotation of all elements concerned. Instrument could not be completed without the accuracy assembly even the previous design was top one. The alignment of infrared optical system always is a tough thing due to the IR material being opaque to visible light which hardly effect on the imaging ability of the system. In this paper a large-aperture IR refractive system was described in details and the alignment of this system was presented. The brief work describes the assembly and integration of the camera barrel in lab. First of all, all the mechanical elements must be manufactured with high accuracy requirements to meet alignment tolerances and minimum errors mostly could be ignored. The rotations relative to the optical axis were hardy restricted by the space between barrel and cells. The lens vertex displacements were determined through high accuracy titanium alloy spacer. So the actual shape data of the optical lenses were obtained by coordinate measuring machining (CMM) to calculate the real space between lenses after alignment1 done. All the measured results were critical for instruction of the practical assemble. Based on the properties and tolerances of the system, the camera barrel includes sets of six lenses with their respective supports and cells which are composed of two parts: the flied lens group and the relay lenses group. The first one was aligned by the geometry centering used CMM. And the relay lenses were integrated one by one after centered individually with a classical centering instrument. Then the two separate components were assembled under the monitor of the CMM with micron precision. Three parameters on the opti-mechanical elements which include decenter, tilt and

  2. Advanced mask aligner lithography: new illumination system.

    PubMed

    Voelkel, Reinhard; Vogler, Uwe; Bich, Andreas; Pernet, Pascal; Weible, Kenneth J; Hornung, Michael; Zoberbier, Ralph; Cullmann, Elmar; Stuerzebecher, Lorenz; Harzendorf, Torsten; Zeitner, Uwe D

    2010-09-27

    A new illumination system for mask aligner lithography is presented. The illumination system uses two subsequent microlens-based Köhler integrators. The second Köhler integrator is located in the Fourier plane of the first. The new illumination system uncouples the illumination light from the light source and provides excellent uniformity of the light irradiance and the angular spectrum. Spatial filtering allows to freely shape the angular spectrum to minimize diffraction effects in contact and proximity lithography. Telecentric illumination and ability to precisely control the illumination light allows to introduce resolution enhancement technologies (RET) like customized illumination, optical proximity correction (OPC) and source-mask optimization (SMO) in mask aligner lithography. PMID:20940992

  3. Experience report with the Alignment Diagnostic System

    SciTech Connect

    Gassner, Georg; /SLAC

    2011-03-03

    Since 2009 an Alignment Diagnostic System (ADS) has been operating at the undulator of the new Linac Coherent Light Source at SLAC National Accelerator Laboratory. The undulator spans a distance of 132 meters and is structured into 33 segments. Each segment is equipped with four hydrostatic leveling sensors and four wire position monitors. This report describes the set up and reflects the experience gained with the ADS.

  4. System Would Keep Telescope Reflector Segments Aligned

    NASA Technical Reports Server (NTRS)

    Mettler, Edward; Eldred, Daniel B.; Briggs, Hugh C.; Agronin, Michael L.; Kiceniuk, Taras

    1991-01-01

    Proposed actuation system maintains alignments of reflector segments of large telescope. Sensors measure positions and orientations of segments. Figure-control computer calculates orientation and figure of overall reflector surface from sensor data. Responding to computer output, servocontroller for each actuator corrects piston and tilt errors of each segment. Actuators adjust segments in response to sensed positions. Concept applicable to such large segmented space-based reflectors as those used in communication and in collection of solar energy.

  5. Test, Control and Monitor System maintenance plan

    NASA Technical Reports Server (NTRS)

    Buehler, David P.; Lougheed, M. J.

    1993-01-01

    The maintenance requirements for Test, Control, and Monitor System (TCMS) and the method for satisfying these requirements prior to First Need Date (FND) of the last TCMS set are described. The method for satisfying maintenance requirements following FND of the last TCMS set will be addressed by a revision to this plan. This maintenance plan serves as the basic planning document for maintenance of this equipment by the NASA Payloads Directorate (CM) and the Payload Ground Operations Contractor (PGOC) at KSC. The terms TCMS Operations and Maintenance (O&M), Payloads Logistics, TCMS Sustaining Engineering, Payload Communications, and Integrated Network Services refer to the appropriate NASA and PGOC organization. For the duration of their contract, the Core Electronic Contractor (CEC) will provide a Set Support Team (SST). One of the primary purposes of this team is to help NASA and PGOC operate and maintain TCMS. It is assumed that SST is an integral part of TCMS O&M. The purpose of this plan is to describe the maintenance concept for TCMS hardware and system software in order to facilitate activation, transition planning, and continuing operation. When software maintenance is mentioned in this plan, it refers to maintenance of TCMS system software.

  6. [Hospital integrated maintenance management system design and application].

    PubMed

    Zeng, Li

    2011-03-01

    According to hospital medical equipment, information equipment and water, electricity and other equipment maintenance procedures, this paper planned and developed a comprehensive maintenance management system for hospitals. The system implements equipment maintenance, maintenance applications, maintenance registration, preventive maintenance, data quantitative analysis and other functions. PMID:21706796

  7. NASA work unit system file maintenance manual

    NASA Technical Reports Server (NTRS)

    1972-01-01

    The NASA Work Unit System is a management information system for research tasks (i.e., work units) performed under NASA grants and contracts. It supplies profiles on research efforts and statistics on fund distribution. The file maintenance operator can add, delete and change records at a remote terminal or can submit punched cards to the computer room for batch update. The system is designed for file maintenance by a person with little or no knowledge of data processing techniques.

  8. Dynamic interferometer alignment and its utility in UV Fourier transform spectrometer systems

    NASA Technical Reports Server (NTRS)

    Dorval, Rick K.; Engel, James R.; Wyntjes, Geert J.

    1993-01-01

    Dynamic alignment has been demonstrated as a practical approach to alignment maintenance for systems in the infrared region of the spectrum. On the basis of work done by OPTRA, this technique was introduced in commercial Fourier transform spectrometer systems in 1982 and in various forms is now available from a number of manufacturers. This paper reports on work by OPTRA to extend the basic technique to systems operating in the ultraviolet. In addition, this paper reports the preliminary results of the development of an alignment system using a laser diode in place of a gas laser normally found in dynamic alignment systems. A unique optical system and spatial heterodyne technique allows for achievement of a metrology system with characteristics that fully satisfy the requirements of an ultraviolet spectrometer system.

  9. Portable weighing system with alignment features

    DOEpatents

    Abercrombie, Robert Knox; Richardson, Gregory David; Scudiere, Matthew Bligh; Sheldon, Frederick T.

    2012-11-06

    A system for weighing a load is disclosed. The weighing system includes a pad having at least one transducer for weighing a load disposed on the pad. In some embodiments the pad has a plurality of foot members and the weighing system may include a plate that disposed underneath the pad for receiving the plurality of foot member and for aligning the foot members when the weighing system is installed. The weighing system may include a spacer disposed adjacent the pad and in some embodiments, a spacer anchor operatively secures the spacer to a support surface, such as a plate, a railway bed, or a roadway. In some embodiments the spacer anchor operatively secures both the spacer and the pad to a roadway.

  10. EMMA: The expert system for munition maintenance

    NASA Technical Reports Server (NTRS)

    Mullins, Barry E.

    1988-01-01

    Expert Missile Maintenance Aid (EMMA) is a first attempt to enhance maintenance of the tactical munition at the field and depot level by using artificial intelligence (AI) techniques. The ultimate goal of EMMA is to help a novice maintenance technician isolate and diagnose electronic, electromechanical, and mechanical equipment faults to the board/chassis level more quickly and consistently than the best human expert using the best currently available automatic test equipment (ATE). To this end, EMMA augments existing ATE with an expert system that captures the knowledge of design and maintenance experts. The EMMA program is described, including the evaluation of field-level expert system prototypes, the description of several study tasks performed during EMMA, and future plans for a follow-on program. This paper will briefly address several study tasks performed during EMMA. The paper concludes with a discussion of future plans for a follow-on program and other areas of concern.

  11. 2011 Status of the Automatic Alignment System for the National Ignition Facility

    SciTech Connect

    Wilhelmsen, K; Awwal, A; Burkhart, S; McGuigan, D; Kamm, V M; Leach, R; Lowe-Webb, R; Wilson, R

    2011-07-19

    Automated alignment for the National Ignition Facility (NIF) is accomplished using a large-scale parallel control system that directs 192 laser beams along the 300-m optical path. The beams are then focused down to a 50-micron spot in the middle of the target chamber. The entire process is completed in less than 50 minutes. The alignment system commands 9,000 stepping motors for highly accurate adjustment of mirrors and other optics. 41 control loops per beamline perform parallel processing services running on a LINUX cluster to analyze high-resolution images of the beams and their references. This paper describes the status the NIF automatic alignment system and the challenges encountered as NIF development has transitioned from building the laser, to becoming a research project supporting a 24 hour, 7 day laser facility. NIF is now a continuously operated system where performance monitoring is increasingly more critical for operation, maintenance, and commissioning tasks. Equipment wear and the effects of high energy neutrons from fusion experiments are issues which alter alignment efficiency and accuracy. New sensors needing automatic alignment assistance are common. System modifications to improve efficiency and accuracy are prevalent. Handling these evolving alignment and maintenance needs while minimizing the impact on NIF experiment schedule is expected to be an on-going challenge for the planned 30 year operational life of NIF.

  12. Optical alignment of Centaur's inertial guidance system

    NASA Technical Reports Server (NTRS)

    Gordan, Andrew L.

    1987-01-01

    During Centaur launch operations the launch azimuth of the inertial platform's U-accelerometer input axis must be accurately established and maintained. This is accomplished by using an optically closed loop system with a long-range autotheodolite whose line of sight was established by a first-order survey. A collimated light beam from the autotheodolite intercepts a reflecting Porro prism mounted on the platform azimuth gimbal. Thus, any deviation of the Porro prism from its predetermined heading is optically detected by the autotheodolite. The error signal produced is used to torque the azimuth gimbal back to its required launch azimuth. The heading of the U-accelerometer input axis is therefore maintained automatically. Previously, the autotheodolite system could not distinguish between vehicle sway and rotational motion of the inertial platform unless at least three prisms were used. One prism was mounted on the inertial platform to maintain azimuth alignment, and two prisms were mounted externally on the vehicle to track sway. For example, the automatic azimuth-laying theodolite (AALT-SV-M2) on the Saturn vehilce used three prisms. The results of testing and modifying the AALT-SV-M2 autotheodolite to simultaneously monitor and maintain alignment of the inertial platform and track the sway of the vehicle from a single Porro prism.

  13. Ultrasonic dip seal maintenance system

    DOEpatents

    Poindexter, Allan M.; Ricks, Herbert E.

    1978-01-01

    A system for removing impurities from the surfaces of liquid dip seals and or wetting the metal surfaces of liquid dip seals in nuclear components. The system comprises an ultrasonic transducer that transmits ultrasonic vibrations along an ultrasonic probe to the metal and liquid surfaces of the dip seal thereby loosening and removing those impurities.

  14. Maintenance of photovoltaic power systems, revision 1

    NASA Astrophysics Data System (ADS)

    Hall, M. R.

    1985-06-01

    This publication establishes standard practices for inspection, testing, and maintenance of photovoltaic power systems at Department of the Navy installations. The practices and procedures are recommended to ensure reliable operation of the power systems. The manual covers photovoltaic-array, battery, voltage-regulator, inverter, and wiring subsystems. In addition, this manual provides a troubleshooting guide and self-study questions and answers.

  15. System modeling of the Thirty Meter Telescope alignment and phasing system

    NASA Astrophysics Data System (ADS)

    Dekens, Frank G.; Seo, Byoung-Joon; Troy, Mitchell

    2014-08-01

    We have developed a system model using the System Modeling Language (SysML) for the Alignment and Phasing System (APS) on the Thirty Meter Telescope (TMT). APS is a Shack-Hartmann wave-front sensor that will be used to measure the alignment and phasing of the primary mirror segments, and the alignment of the secondary and tertiary mirrors. The APS system model contains the ow-down of the Level 1 TMT requirements to APS (Level 2) requirements, and from there to the APS sub-systems (Level 3) requirements. The model also contains the operating modes and scenarios for various activities, such as maintenance alignment, post-segment exchange alignment, and calibration activities. The requirements ow-down is captured in SysML requirements diagrams, and we describe the process of maintaining the DOORS database as the single-source-of-truth for requirements, while using the SysML model to capture the logic and notes associated with the ow-down. We also use the system model to capture any needed communications from APS to other TMT systems, and between the APS sub-systems. The operations are modeled using SysML activity diagrams, and will be used to specify the APS interface documents. The modeling tool can simulate the top level activities to produce sequence diagrams, which contain all the communications between the system and subsystem needed for that activity. By adding time estimates for the lowest level APS activities, a robust estimate for the total time on-sky that APS requires to align and phase the telescope can be obtained. This estimate will be used to verify that the time APS requires on-sky meets the Level 1 TMT requirements.

  16. Power systems handbook: Design, operation and maintenance

    SciTech Connect

    Seevers, O.C.

    1991-01-01

    This handbook contains innovative methods for improving and streamlining all phases of electric utility operation outside the power plant. Part One describes step by step through each element of system operation and maintenance, covering such specifics as land rights, tree clearance, lightning and effective grounding, pole maintenance, switch maintenance, OCR and oil switch maintenance, meter testing, inspections, preventive maintenance, system coordination, substation construction, and effective use of contractors. Also presented is a comprehensive efficiency rating system developed by the author to systematically assess all aspects of operations and determine where improvements are feasible. It describes a simple, accurate and effective computerized load management program which can be used to insure optimum transformer and line loading, phase balance, and system coordination. Maintenance operations may benefit from a time-tested computerized program of trouble analysis which makes it possible to eliminate many potential problems before they occur. Part Two describes twenty-eight unique power system problems which the author has encountered in every phase of operation, and presents a proven solution for each. Covering such scenarios as mysterious equipment failures, unexplained voltages, unanticipated grounding problems, and lightning and icing problems, this section guides one to an understanding of not only the solution, but the systematic assessment process which led to that solution. Phase rotation and phase sequence are explained in clear terms, and difficult calculations involving value of losses, reduced voltage drops, motor dip and system impedances are simplified. This handbook provides a powerful problem-solving desk reference for electric utility engineers, managers and superintendents, as well as for consultants who work within the utility industry.

  17. Recent advances in automatic alignment system for the National Iginition Facility

    SciTech Connect

    Wilhelmsen, K; Awwal, A; Kalantar, D; Leach, R; Lowe-Webb, R; McGuigan, D; Kamm, V

    2010-12-08

    The automatic alignment system for the National Ignition Facility (NIF) is a large-scale parallel system that directs all 192 laser beams along the 300-m optical path to a 50-micron focus at target chamber in less than 50 minutes. The system automatically commands 9,000 stepping motors to adjust mirrors and other optics based upon images acquired from high-resolution digital cameras viewing beams at various locations. Forty-five control loops per beamline request image processing services running on a LINUX cluster to analyze these images of the beams and references, and automaticallys teer the beams toward the target. This paper discusses the upgrades to the NIF automatic alignment system to handle new alignment needs and evolving requirements as related to various types of experiments performed. As NIF becomes a continuously-operated system and more experiments are performed, performance monitoring is increasingly important for maintenance and commissioning work. Data, collected during operations, is analyzed for tuning of the laser and targeting maintenance work. handling evolving alignment and maintenance needs is expected for the planned 30-year operational life of NIF.

  18. Far-field detection system for laser beams alignment and crystals alignment

    NASA Astrophysics Data System (ADS)

    Liu, D.; Qin, H.; Zhu, B.

    2015-08-01

    Laser beams far-field alignment is very important for the high power laser facility as well as the frequency doubling crystals adjustment. Traditional beams alignment system and crystals alignment system are separated. That means, they use different optical image systems and CCD cameras, which will occupy larger space and use more money. A new farfield detection system of laser beams is presented with a big diffraction grating (37mm*37mm), a set of optical imaging components and a high resolution CCD camera. This detection system, which is fully demonstrated on the National Laser Facility of Israel, can align high power laser facility beams' direction as well as the frequency doubling crystals. The new system occupies small space in the spatial filter through off-axial grating sampling. The experimental results indicate that the average far-field alignment error is less than 5% of spatial filter pinhole diameter, and the average crystals' matching angle error is less than 10urad, which meet the alignment system requirements for beams and crystals.

  19. Implementation of a Computerized Maintenance Management System

    NASA Technical Reports Server (NTRS)

    Shen, Yong-Hong; Askari, Bruce

    1994-01-01

    A primer Computerized Maintenance Management System (CMMS) has been established for NASA Ames pressure component certification program. The CMMS takes full advantage of the latest computer technology and SQL relational database to perform periodic services for vital pressure components. The Ames certification program is briefly described and the aspects of the CMMS implementation are discussed as they are related to the certification objectives.

  20. Generalized Training Devices for Avionic Systems Maintenance.

    ERIC Educational Resources Information Center

    Parker, Edward L.

    A research study was conducted to determine the feasibility and desirability of developing generalized training equipment for use in avionic systems maintenance training. The study consisted of a group of survey and analytic tasks to provide useful guidance to serve the needs of the Naval Aviation community in future years. The study had four…

  1. Corrective optics space telescope axial replacement alignment system

    NASA Astrophysics Data System (ADS)

    Slusher, Robert B.; Satter, Michael J.; Kaplan, Michael L.; Martella, Mark A.; Freymiller, Ed D.; Buzzetta, Victor

    1993-10-01

    To facilitate the accurate placement and alignment of the corrective optics space telescope axial replacement (COSTAR) structure, mechanisms, and optics, the COSTAR Alignment System (CAS) has been designed and assembled. It consists of a 20-foot optical bench, support structures for holding and aligning the COSTAR instrument at various stages of assembly, a focal plane target fixture (FPTF) providing an accurate reference to the as-built Hubble Space Telescope (HST) focal plane, two alignment translation stages with interchangeable alignment telescopes and alignment lasers, and a Zygo Mark IV interferometer with a reference sphere custom designed to allow accurate double-pass operation of the COSTAR correction optics. The system is used to align the fixed optical bench (FOB), the track, the deployable optical bench (DOB), the mechanisms, and the optics to ensure that the correction mirrors are all located in the required positions and orientations on-orbit after deployment. In this paper, the layout of the CAS is presented and the various alignment operations are listed along with the relevant alignment requirements. In addition, calibration of the necessary support structure elements and alignment aids is described, including the two-axis translation stages, the latch positions, the FPTF, and the COSTAR-mounted alignment cubes.

  2. Shear alignment of lamellar mesophase systems

    NASA Astrophysics Data System (ADS)

    Jaju, S. J.; Kumaran, V.

    2015-11-01

    Mixtures of oil, water and surfactants form different microphases. Some of these phases, e.g. lamellar, hexagonal phases, lead to complex rheological behaviour at macroscale due to inherent anisotropy and irregularities in the microstructures. We present a comprehensive simulation study to examine the structure-rheology relationship in lamellar phase flow. At mesoscale, Reynolds number (Re), Schmidt number (Sc), Ericksen number (Er), extent of segregation between hydrophilic and hydrophobic components (r), ratio of viscosity of the two components (Δμ /μ0), and system size to layer width ratio (L / λ) complete the lamellar phase description. We have used lattice Boltzmann simulations to study a two dimensional lamellar phase system of moderate size. The domains and grain boundaries seen at low Sc are replaced by isolated edge dislocations at high Sc. The alignment mechanism does not change with changes in layer bending moduli (Er), viscosity contrast or r. Increasing segregation, increases disorder; this however does not lead to higher resistance to flow. At high Er, the shear tries homogenise the concentration field and disrupt layer formation. We see significantly higher peak viscosity at low Er at high viscosity contrast and due to defect pinning. The authors would like to thank the Department of Science and Technology, Government of India for financial support, and Supercomputer Education and Research Centre at Indian Institute of Science for the computational resources.

  3. CB-EMIS MAINTENANCE MONITORING SYSTEM

    2006-10-01

    This system continuously monitors all components of a CB-EMIS (ANL-02-078)installation such as signals for video cameras, detector, train data, meteorological data, computer and network equipment and reports exceptions to maintenance staff so that corrections can be made as soon as possible. This monitoring system is built within Nagios (www.nagios.org), a free open source host service and network monitoring program.

  4. Machine Maintenance Integrated Performance Support System

    SciTech Connect

    Bohley, M.C.; Schwartz, M.E.

    1998-03-11

    The objectives of this partnership project were to develop a preventive maintenance checklist program, a troubleshooting system for the Vertical Turning Center (VTC)-5, an on-line manual, and to integrate these components with a custom browser that would run on the VTC-5 machine's controller and would support future internet/intranet delivery. Kingsbury provided subject matter experts from engineering, manufacturing, and technical support. They also provided photographs, schematics, and CAD drawings, which AlliedSignal Federal Manufacturing and Technologies (ASFM and T) digitized for use in the final program. Information from The Kingsbury troubleshooting experts were interviewed regarding symptoms and root causes of system malfunctions This knowledge was captured and from it, fault trees were developed. These trees were then incorporated into the EPSS as a troubleshooting tool. The troubleshooting portion of the system presents simple questions to the machine operator in order to determine the likely cause or causes of malfunctions and then recommends systematic corrective actions. The on-line reference manual, covering operations and maintenance, provides text and illustrations to the machine operator in a traditional structure, but additionally offers the capability to search voluminous amounts of technical data and retrieve specific information on request. The maintenance portion of the EPSS includes checklists that are displayed daily, weekly, monthly, and annually, as appropriate, on the VTC-5 controller screen. The controller software is unavailable for machining parts until the machine tool operator goes through and checks off all of the checklist items. This project provided the team with a detailed understanding of the knowledge and information required to produce and support advanced machine tools. In addition, it resulted in the design and construction of a prototype VTC-5 EPSS containing all the logic and interfaces necessary to integrate operations

  5. A PC based computerized maintenance system

    SciTech Connect

    Pruett, D.P.; Walker, G.D.; Imel, G.R.

    1990-03-01

    The present regulatory climate in the research reactor community has made an easily manageable and auditable maintenance system a necessity. We at NRAD have developed a computer-based system that is easy to implement and use, meets all our regulatory and reporting requirements, and is extremely useful to us in our daily operations. The system, developed at the NRAD reactor facility at Argonne National Laboratory in Idaho Falls, Idaho, uses DBASE-III coupled with C language routines, written for specific purposes. It is a menu-driven system that can be mastered in a short period of time and maintained with only a few hours of computer operation per month. It uses three computer processes: job scheduling, file updating, and report preparation, to produce schedules, work orders, and miscellaneous report forms. The heart of the system is an IBM PC with a 10 MB hard disk, providing adequate data storage capacity for a facility the size of NRAD. The computer is totally dedicated to the maintenance system, thus guarding against inadvertent loss of, or damage to, data files. Computer operator training time is minimized by the menu driven program. Multiple operators can share the computer operation responsibilities, and maintain the system with only 12 to 16 hours of computer operation per month. The system is adaptable to almost any facility, and can be altered and expanded to satisfy changing requirements. 7 figs.

  6. Survey and Alignment of the Fermilab Electron Cooling System

    SciTech Connect

    Oshinowo, Babatunde O'Sheg; Leibfritz, Jerry

    2006-09-01

    The goal of achieving the Tevatron luminosity of 3 x 10{sup 32} cm{sup -2}s{sup -1} requires Electron Cooling in the Recycler Ring to provide an increased flux of antiprotons. The Fermilab Electron Cooling system has been designed to assist accumulation of antiprotons for the Tevatron collider operations. The installation along with the survey and alignment of the Electron Cooling system in the Recycler Ring were completed in November 2004. The Electron Cooling system was fully commissioned in May 2005 and the first cooling of antiprotons was achieved in July 2005. This paper discusses the alignment methodology employed to survey and align the Electron Cooling system.

  7. A comparative study of two different clear aligner systems

    PubMed Central

    2014-01-01

    Background This study aims to compare the ‘Nuvola®’ system with ‘Fantasmino®’ system, examine their material properties, and define the indications for use of the aligners. Methods Two groups of patients were selected and were respectively treated with Nuvola® aligner and Fantasmino® system. Results The goal of treatment has been achieved with the two systems. Conclusions The two types of aligners have shown differences during the treatment. Fantasmino® system has elastic properties of high performance, but its size does not encourage compliance throughout the day. Nuvola® system determines good tooth movement and its size facilitates the patient’s collaboration. In both aligner systems, difficulties were found in the correction of torque information and rotations. PMID:24934094

  8. [Maintenance and monitoring of water treatment system].

    PubMed

    Pontoriero, G; Pozzoni, P; Tentori, F; Scaravilli, P; Locatelli, F

    2005-01-01

    Water treatment systems must be submitted to maintenance, disinfections and monitoring periodically. The aim of this review is to analyze how these processes must complement each other in order to preserve the efficiency of the system and optimize the dialysis fluid quality. The correct working of the preparatory process (pre-treatment) and the final phase of depuration (reverse osmosis) of the system need a periodic preventive maintenance and the regular substitution of worn or exhausted components (i.e. the salt of softeners' brine tank, cartridge filters, activated carbon of carbon tanks) by a competent and trained staff. The membranes of reverse osmosis and the water distribution system, including dialysis machine connections, should be submitted to dis-infections at least monthly. For this purpose it is possible to use chemical and physical agents according to manufacturer' recommendations. Each dialysis unit should predispose a monitoring program designed to check the effectiveness of technical working, maintenance and disinfections and the achievement of chemical and microbiological standards taken as a reference. Generally, the correct composition of purified water is monitored by continuous measuring of conductivity, controlling bacteriological cultures and endotoxin levels (monthly) and checking water contaminants (every 6-12 months). During pre-treatment, water hardness (after softeners) and total chlorine (after chlorine tank) should be checked periodically. Recently the Italian Society of Nephrology has developed clinical guidelines for water and dialysis solutions aimed at suggesting rational procedures for production and monitoring of dialysis fluids. It is hopeful that the application of these guidelines will lead to a positive cultural change and to an improvement in dialysis fluid quality. PMID:16342048

  9. Mask-to-wafer alignment system

    DOEpatents

    Sweatt, William C.; Tichenor, Daniel A.; Haney, Steven J.

    2003-11-04

    A modified beam splitter that has a hole pattern that is symmetric in one axis and anti-symmetric in the other can be employed in a mask-to-wafer alignment device. The device is particularly suited for rough alignment using visible light. The modified beam splitter transmits and reflects light from a source of electromagnetic radiation and it includes a substrate that has a first surface facing the source of electromagnetic radiation and second surface that is reflective of said electromagnetic radiation. The substrate defines a hole pattern about a central line of the substrate. In operation, an input beam from a camera is directed toward the modified beam splitter and the light from the camera that passes through the holes illuminates the reticle on the wafer. The light beam from the camera also projects an image of a corresponding reticle pattern that is formed on the mask surface of the that is positioned downstream from the camera. Alignment can be accomplished by detecting the radiation that is reflected from the second surface of the modified beam splitter since the reflected radiation contains both the image of the pattern from the mask and a corresponding pattern on the wafer.

  10. [New concepts in aligner therapy with the orthocaps system].

    PubMed

    Khan, Wajeeh

    2014-09-01

    Orthodontic tooth movement with aligners poses challenges peculiar to removable appliances. The mechanical limitations of aligners can be overcome, to some extent, by increasing the aligner grip on teeth as well as by choosing elastic materials in their fabrication. Sound planning together with the use of auxiliaries can result in obtaining satisfactory results for the patients who seek an aesthetically pleasing and comfortable alternative to fixed appliance systems. The salient features of the Orthocaps System are the use of elastic thermoplastics, precision scanning, high pressure thermoforming, 3D interactive set-ups for treatment planning and approval, treatment evaluation at regular intervals during treatment and a unique attachment design (friction pads). PMID:25158748

  11. 49 CFR 192.747 - Valve maintenance: Distribution systems.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 3 2014-10-01 2014-10-01 false Valve maintenance: Distribution systems. 192.747... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Maintenance § 192.747 Valve maintenance: Distribution systems. (a) Each valve, the use of which may be necessary for the safe operation...

  12. 49 CFR 192.747 - Valve maintenance: Distribution systems.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 3 2013-10-01 2013-10-01 false Valve maintenance: Distribution systems. 192.747... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Maintenance § 192.747 Valve maintenance: Distribution systems. (a) Each valve, the use of which may be necessary for the safe operation...

  13. 49 CFR 192.747 - Valve maintenance: Distribution systems.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 3 2012-10-01 2012-10-01 false Valve maintenance: Distribution systems. 192.747... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Maintenance § 192.747 Valve maintenance: Distribution systems. (a) Each valve, the use of which may be necessary for the safe operation...

  14. 49 CFR 192.747 - Valve maintenance: Distribution systems.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 3 2010-10-01 2010-10-01 false Valve maintenance: Distribution systems. 192.747... TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS Maintenance § 192.747 Valve maintenance: Distribution systems. (a) Each valve, the use of which may be necessary for the safe operation...

  15. Autonomous monitoring of control hardware to predict off-normal conditions using NIF automatic Alignment Systems

    SciTech Connect

    Awwal, A; Wilhelmsen, K; Leach, R; Kamm, V M; Burkhart, S; Lowe-Webb, R; Cohen, S

    2011-07-20

    The National Ignition Facility (NIF) is a high power laser system capable of supporting high-energy-density experimentation as a user facility for the next 30 years. In order to maximize the facility availability, preventive maintenance enhancements are being introduced into the system. An example of such an enhancement is a camera-based health monitoring system, integrated into the automated alignment system, which provides an opportunity to monitor trends in measurements such as average beam intensity, size of the beam, and pixel saturation. The monitoring system will generate alerts based on observed trends in measurements to allow scheduled pro-active maintenance before routine off-normal detection stops system operations requiring unscheduled intervention.

  16. Rigorous electromagnetic simulation applied to alignment systems

    NASA Astrophysics Data System (ADS)

    Deng, Yunfei; Pistor, Thomas V.; Neureuther, Andrew R.

    2001-09-01

    Rigorous electromagnetic simulation with TEMPEST is used to provide benchmark data and understanding of key parameters in the design of topographical features of alignment marks. Periodic large silicon trenches are analyzed as a function of wavelength (530-800 nm), duty cycle, depth, slope and angle of incidence. The signals are well behaved except when the trench width becomes about 1 micrometers or smaller. Segmentation of the trenches to form 3D marks shows that a segmentation period of 2-5 wavelengths makes the diffraction in the (1,1) direction about 1/3 to 1/2 of that in the main first order (1,0). Transmission alignment marks nanoimprint lithography using the difference between the +1 and -1 reflected orders showed a sensitivity of the difference signal to misalignment of 0.7%/nm for rigorous simulation and 0.5%/nm for simple ray-tracing. The sensitivity to a slanted substrate indentation was 10 nm off-set per degree of tilt from horizontal.

  17. Laboratory services series: a programmed maintenance system

    SciTech Connect

    Tuxbury, D.C.; Srite, B.E.

    1980-01-01

    The diverse facilities, operations and equipment at a major national research and development laboratory require a systematic, analytical approach to operating equipment maintenance. A computer-scheduled preventive maintenance program is described including program development, equipment identification, maintenance and inspection instructions, scheduling, personnel, and equipment history.

  18. VISA UNDULATOR RE-ALIGNMENT USING AN OPTICAL MONITORING SYSTEM.

    SciTech Connect

    TREMAINE,A.; MUROKH,A.; WANG,X.J.

    2001-01-01

    The VISA experiment is designed to reach and study saturation in a high gain 800nm SASE FEL at the Brookhaven Accelerator Test Facility (ATF). To do this, the undulator must be aligned at first to within 20 {micro}m with use of a laser interferometric system. Once aligned, any small movements from the aligned position will greatly detriment the SASE FEL performance thus making continuous monitoring of the undulator position necessary. This is quite a complicated task since the 4m undulator is made up of four 1m sections enclosed in a vacuum chamber. We have developed an in situ optical system to monitor the undulator position with an accuracy better than 10 {micro}m. In addition, we have demonstrated the accuracy of this system by bringing the grossly misaligned VISA undulator ({approximately} 500 {micro}m in some locations) into alignment and attaining very high gain of the SASE FEL.

  19. MEDEMAS -Medical Device Management and Maintenance System Architecture

    NASA Astrophysics Data System (ADS)

    Dogan, Ülkü Balcı; Dogan, Mehmet Ugur; Ülgen, Yekta; Özkan, Mehmed

    In the proposed study, a medical device maintenance management system (MEDEMAS) is designed and implemented which provides a data pool of medical devices, the maintenance protocols and other required information for these devices. The system also contains complete repair and maintenance history of a specific device. MEDEMAS creates optimal maintenance schedule for devices and enables the service technician to carry out and report maintenance/repair processes via remote access. Thus predicted future failures are possible to prevent or minimize. Maintenance and repair is essential for patient safety and proper functioning of the medical devices, as it prevents performance decrease of the devices, deterioration of the equipment, and detrimental effects on the health of a patient, the user or other interacting people. The study aims to make the maintenance process more accurate, more efficient, faster and easier to manage and organize; and much less confusing. The accumulated history of medical devices and maintenance personnel helps efficient facility planning.

  20. Advanced Ground Systems Maintenance Prognostics Project

    NASA Technical Reports Server (NTRS)

    Perotti, Jose M.

    2015-01-01

    The project implements prognostics capabilities to predict when a component system or subsystem will no longer meet desired functional or performance criteria, called the end of life. The capability also provides an assessment of the remaining useful life of a hardware component. The project enables the delivery of system health advisories to ground system operators. This project will use modeling techniques and algorithms to assess components' health andpredict remaining life for such components. The prognostics capability being developed will beused:during the design phase and during pre/post operations to conduct planning and analysis ofsystem design, maintenance & logistics plans, and system/mission operations plansduring real-time operations to monitor changes to components' health and assess their impacton operations.This capability will be interfaced to Ground Operations' command and control system as a part ofthe AGSM project to help assure system availability and mission success. The initial modelingeffort for this capability will be developed for Liquid Oxygen ground loading applications.

  1. Systemic treatment: maintenance compared with holiday.

    PubMed

    Punt, Cornelis J A; Simkens, Lieke H J; Koopman, Miriam

    2015-01-01

    With the currently available cytotoxic and targeted drugs, metastatic colorectal cancer (mCRC) may be controlled by systemic treatment for a substantial period of time. However, many questions remain about the optimal use of drugs and duration of treatment. The feasibility of chemotherapy-free intervals has been studied in patients with mCRC treated with chemotherapy alone, but the results are conflicting. Current data show that oxaliplatin may be safely interrupted, but they do not allow a firm conclusion on the safety of a full treatment break of chemotherapy. For targeted therapy, continuous inhibition of intracellular signaling by prolonged administration would theoretically be beneficial for efficacy of treatment. Recent data support the use of maintenance treatment with chemotherapy and bevacizumab. No data on the optimal duration of treatment with anti-epidermal growth factor receptor (EGFR) agents are currently available. PMID:25993146

  2. 33 CFR 106.255 - Security systems and equipment maintenance.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... SECURITY MARITIME SECURITY MARINE SECURITY: OUTER CONTINENTAL SHELF (OCS) FACILITIES Outer Continental Shelf (OCS) Facility Security Requirements § 106.255 Security systems and equipment maintenance....

  3. 33 CFR 106.255 - Security systems and equipment maintenance.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... SECURITY MARITIME SECURITY MARINE SECURITY: OUTER CONTINENTAL SHELF (OCS) FACILITIES Outer Continental Shelf (OCS) Facility Security Requirements § 106.255 Security systems and equipment maintenance....

  4. 33 CFR 106.255 - Security systems and equipment maintenance.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... SECURITY MARITIME SECURITY MARINE SECURITY: OUTER CONTINENTAL SHELF (OCS) FACILITIES Outer Continental Shelf (OCS) Facility Security Requirements § 106.255 Security systems and equipment maintenance....

  5. 33 CFR 106.255 - Security systems and equipment maintenance.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... SECURITY MARITIME SECURITY MARINE SECURITY: OUTER CONTINENTAL SHELF (OCS) FACILITIES Outer Continental Shelf (OCS) Facility Security Requirements § 106.255 Security systems and equipment maintenance....

  6. 33 CFR 106.255 - Security systems and equipment maintenance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... SECURITY MARITIME SECURITY MARINE SECURITY: OUTER CONTINENTAL SHELF (OCS) FACILITIES Outer Continental Shelf (OCS) Facility Security Requirements § 106.255 Security systems and equipment maintenance....

  7. Boresight alignment method for mobile laser scanning systems

    NASA Astrophysics Data System (ADS)

    Rieger, P.; Studnicka, N.; Pfennigbauer, M.; Zach, G.

    2010-06-01

    Mobile laser scanning (MLS) is the latest approach towards fast and cost-efficient acquisition of 3-dimensional spatial data. Accurately evaluating the boresight alignment in MLS systems is an obvious necessity. However, recent systems available on the market may lack of suitable and efficient practical workflows on how to perform this calibration. This paper discusses an innovative method for accurately determining the boresight alignment of MLS systems by employing 3D laser scanners. Scanning objects using a 3D laser scanner operating in a 2D line-scan mode from various different runs and scan directions provides valuable scan data for determining the angular alignment between inertial measurement unit and laser scanner. Field data is presented demonstrating the final accuracy of the calibration and the high quality of the point cloud acquired during an MLS campaign.

  8. Relay telescope for high power laser alignment system

    DOEpatents

    Dane, C. Brent; Hackel, Lloyd; Harris, Fritz B.

    2006-09-19

    A laser system includes an optical path having an intracavity relay telescope with a telescope focal point for imaging an output of the gain medium between an image location at or near the gain medium and an image location at or near an output coupler for the laser system. A kinematic mount is provided within a vacuum chamber, and adapted to secure beam baffles near the telescope focal point. An access port on the vacuum chamber is adapted for allowing insertion and removal of the beam baffles. A first baffle formed using an alignment pinhole aperture is used during alignment of the laser system. A second tapered baffle replaces the alignment aperture during operation and acts as a far-field baffle in which off angle beams strike the baffle a grazing angle of incidence, reducing fluence levels at the impact areas.

  9. Health maintenance facility system effectiveness testing

    NASA Technical Reports Server (NTRS)

    Lloyd, Charles W.; Gosbee, John; Bueker, Richard; Kupra, Debra; Ruta, Mary

    1993-01-01

    The Medical Simulations Working Group conducted a series of medical simulations to evaluate the proposed Health Maintenance Facility (HMF) Preliminary Design Review (PDR) configuration. The goal of these simulations was to test the system effectiveness of the HMF PDR configurations. The objectives of the medical simulations are to (1) ensure fulfillment of requirements with this HMF design, (2) demonstrate the conformance of the system to human engineering design criteria, and (3) determine whether undesirable design or procedural features were introduced into the design. The simulations consisted of performing 6 different medical scenarios with the HMF mockup in the KRUG laboratory. The scenarios included representative medical procedures and used a broad spectrum of HMF equipment and supplies. Scripts were written and simulations performed by medical simulations working group members under observation from others. Data were collected by means of questionnaires, debriefings, and videotapes. Results were extracted and listed in the individual reports. Specific issues and recommendations from each simulation were compiled into the individual reports. General issues regarding the PDR design of the HMF are outlined in the summary report.

  10. High resolution Fresnel zone plate laser alignment system

    SciTech Connect

    Bressler, V.E.; Fischer, G.E.; Ruland, R.E.; Wang, T.

    1992-03-01

    The existing Fresnel zone plate laser alignment system is currently being extended and upgraded for the Final Focus Test Beam (FFTB). Previously, the resolution of this system has been several tens of micrometers. After the upgrade, the resolution will be a few micrometers. Details of the upgrade as well as simulation and experimental results will be presented.

  11. 49 CFR 192.747 - Valve maintenance: Distribution systems.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 49 Transportation 3 2011-10-01 2011-10-01 false Valve maintenance: Distribution systems. 192.747... maintenance: Distribution systems. (a) Each valve, the use of which may be necessary for the safe operation of a distribution system, must be checked and serviced at intervals not exceeding 15 months, but...

  12. 33 CFR 104.260 - Security systems and equipment maintenance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... maintenance. 104.260 Section 104.260 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND... systems and equipment maintenance. (a) Security systems and equipment must be in good working order and... procedures for identifying and responding to security system and equipment failures or malfunctions....

  13. Flexible polymeric rib waveguide with self-align couplers system.

    PubMed

    Huang, Cheng-Sheng; Wang, Wei-Chih

    2008-01-01

    The authors report a polymeric based rib waveguide with U shape self-align fiber couplers system using a simple micromolding process with SU8 as a molding material and polydimethysiloxane as a waveguide material. The material is used for its good optical transparency, low surface tension, biocompatibility, and durability. Furthermore, the material is highly formable. This unique fabrication molding technique provides a means of keeping the material and manufacturing costs to a minimum. The self-align fiber couplers system also proves a fast and simple means of light coupling. The flexible nature of the waveguide material makes this process ideal for a potential wearable optical sensor. PMID:22171151

  14. AXAF Alignment Test System Autocollimating Flat Error Correction

    NASA Technical Reports Server (NTRS)

    Lewis, Timothy S.

    1995-01-01

    The alignment test system for the advanced x ray astrophysics facility (AXAF) high-resolution mirror assembly (HRMA) determines the misalignment of the HRMA by measuring the displacement of a beam of light reflected by the HRMA mirrors and an autocollimating flat (ACF). This report shows how to calibrate the system to compensate for errors introduced by the ACF, using measurements taken with the ACF in different positions. It also shows what information can be obtained from alignment test data regarding errors in the shapes of the HRMA mirrors. Simulated results based on measured ACF surface data are presented.

  15. Alignment and calibration of a focal neurotransmitter uncaging system.

    PubMed

    Sarkisov, Dmitry V; Wang, Samuel S-H

    2006-01-01

    Photolysis of caged compounds is a powerful tool for studying subcellular physiological functions. Here we describe protocols for the alignment and calibration of a focal uncaging system. We also report procedures for convenient quantitative calibration of uncaging. Using these methods, we can achieve submicron lateral resolution of photolysis and probe biological function in spines, the smallest signaling compartments of neurons. Initially, the entire alignment procedure takes 4-6 h to perform; periodic fine-tuning of the system takes 1-2 h. PMID:17406314

  16. Maintenance components for Space Station long life fluid systems

    NASA Technical Reports Server (NTRS)

    Greene, John B., Jr.; Roebelen, George J., Jr.; Owen, James W.

    1986-01-01

    The Space Station elements or modules will maintain thermal conditioning by way of fluid systems. Because of the Station's 20 year minimum orbital lifetime, these fluid system designs must allow for on-orbit maintenance. This paper describes the maintenance assessment of the various Space Station thermal control system options, their components and the recommended maintenance approach for each. The design and utilization of the primary fluid isolation servicing method, the Maintainable Maintenance Disconnect Valve (MMDV) and the effects of selecting different levels for the orbital replacement unit (ORU) are also presented.

  17. Maintenance evaluation for space station liquid systems

    NASA Technical Reports Server (NTRS)

    Flugel, Charles

    1987-01-01

    Many of the thermal and environmental control life support subsystems as well as other subsystems of the space station utilize various liquids and contain components which are either expendables or are life-limited in some way. Since the space station has a 20-year minimum orbital lifetime requirement, there will also be random failures occurring within the various liquid-containing subsystems. These factors as well as the planned space station build-up sequence require that maintenance concepts be developed prior to the design phase. This applies to the equipment which needs maintenance as well as the equipment which may be required at a maintenance work station within the space station. This paper presents several maintenance concepts for liquid-containing items and a flight experiment program which would allow for evaluation and improvement of these concepts so they can be incorporated in the space station designs at the outset of its design phase.

  18. Increment 23/24 Critical Readiness Review Health Maintenance System

    NASA Technical Reports Server (NTRS)

    Nieschwitz, Linda

    2010-01-01

    This slide presentation reviews the Health Maintenance System. It includes information on the carbon dioxide (CO2) and moisture removal system (CMRS), the variable oxygen system,rendevous station panels, and the crew contamination protection kit (CCPK).

  19. Towards a General-Purpose Belief Maintenance System.

    ERIC Educational Resources Information Center

    Falkenhainer, Brian

    This paper addresses the problem of probabilistic reasoning as it applies to Truth Maintenance Systems (TMS). A computer-based Belief Maintenance System (BMS) has been constructed which manages a current set of probabilistic beliefs in much the same way that a TMS manages a set of true/false beliefs. It may be thought of as a generalization of a…

  20. Alignment Systems For Subassemblies Of Overmolded Optoeletronic Modules

    DOEpatents

    Chan, Benson; Fortier, Paul F.; Guindon, Francois M.; Johnson, Glen W.; Letourneau, Martial A.; Sherman, John H.; Tetreault, Real

    2003-04-15

    Alignment systems for optoelectronic modules with overmolded chip carriers include drilled or milled substrate corners for engaging dowel pins to precisely align the substrate in a mold for molding an overmold frame on the substrate. The overmold frame includes slot and trilobe holes for receiving retainer posts to precisely align a retainer assembly on the overmold frame. Cooperating standoff pads on the overmold frame and on the retainer assembly stabilize the assembly of these components and provide a precise gap for receiving an adhesive to permanently attach these two components. The retainer assembly carries optoelectronic components that include a flexible circuit, and a distal end portion of this flexible circuit and walls of a receiving cavity in the overmold frame have cooperating features for precisely aligning distal electrical leads of the flexible circuit with an array of electrical pads on the substrate. A permanent shroud on a proximate end portion of the flexible circuit protects and helps align proximate electrical leads with electrical pads on optic dies and their carriers.

  1. The art of planning for optical systems integration and alignment

    NASA Astrophysics Data System (ADS)

    Sullivan, Joseph F.

    2015-09-01

    This will address Lessons Learned on the approaches that worked or did not work over various programs when integrating and aligning elements into fairly complex optical systems. The appropriate planning can prevent many unnecessary headaches and achieve the desired optical performance while optimizing integration efficiency.

  2. FY 2005 Quantum Cascade Laser Alignment System Final Report

    SciTech Connect

    Myers, Tanya L.; Cannon, Bret D.; Wojcik, Michael D.; Broocks, Bryan T.; Stewart, Timothy L.; Hatchell, Brian K.

    2006-01-11

    The Alignment Lasers Task of Pacific Northwest National Laboratory's (PNNL's) Remote Spectroscopy Project (Project PL211I) is a co-funded project between DOE NA-22 and a Classified Client. This project, which began in the second half of FY03, involved building and delivering a Quantum Cascade (QC) Laser Alignment System to be used for testing the pupil alignment of an infrared sensor by measuring the response from four pairs of diametrically opposed QC lasers. PNNL delivered the system in FY04 and provided technical assistance in FY05 culminating into a successful demonstration of the system. This project evolved from the Laser Development Task of PL211I, which is involved in developing novel laser technology to support development of advanced chemical sensors for detecting the proliferation of nuclear weapons. The laser systems are based on quantum cascade (QC) lasers, a new semiconductor source in the infrared. QC lasers can be tailored to emit light throughout the infrared region (3.5 ? 17 ?m) and have high output power and stability. Thus, these lasers provide an infrared source with superb power and spectral stability enabling them to be used for applications such as alignment and calibration in addition to chemical sensing.

  3. Alignment of Two Grading Systems: A Case Study

    ERIC Educational Resources Information Center

    Hohner, Margaret; Tsigaris, Panagiotis

    2010-01-01

    For the past number of years, a Canadian university has been offering its business degree program in universities located in Tianjin and Shanghai, China. This paper examines the alignment of the two grading systems and its implications on the grade distribution of graduates from the programs. An attempt is made to find an exchange rate of the two…

  4. Study of a module alignment measuring system for UARS

    NASA Technical Reports Server (NTRS)

    1982-01-01

    An alignment measurement system (AMS) which precisely determines the boresights pointing directions of the Upper Atmosphere Research Satellite (UARS) instruments relative to the UARS attitude control system (ACS) was studied. The technology used in on the MAGSAT mission was considered. The AMS optical, mechanical, thermal and electrical system properties were defined. The AMS is constrained to interface with the UARS instrument module and spacecraft layout.

  5. Panoramic alignment system for optical wireless communication systems

    NASA Astrophysics Data System (ADS)

    Shen, Thomas C.; Drost, Robert J.; Rzasa, John; Sadler, Brian M.; Davis, Christopher C.

    2015-03-01

    Free space optical communication may provide a viable adjunct to radio frequency (RF) technology for mobile communications, especially in "RF-denied" settings in which RF-based communication may be prohibited or impractical. These settings may include military tactical environments or settings which suffer from RF jamming or interference. Unlike many RF communication systems, point-to-point optical communications between mobile nodes typically require establishing and maintaining alignment, which requires each node to have awareness of the locations of neighboring nodes. We propose a method to create this situational awareness between nodes using purely optical means. This method uses a camera that is focused on a hyperboloidal mirror, thus providing a 360-degree view of the surrounding environment. The camera and mirror are used to detect light emitted from the beacon transmitters from neighboring nodes, with the location of the beacon image in the sensor plane of the camera yielding elevation and azimuth information of the beacon. The beacon transmitter itself is modulated, allowing it to be distinguished from the environment. In discussing our experimental realization of this system, we assess its performance.

  6. Alignment and diagnostics on the National Ignition Facility laser system

    SciTech Connect

    Bliss, E S; Boege, S J; Boyd, B; Demaret, R D; Feldman, M; Gates, A J; Holdener, F R; Hollis, J; Knopp, C F; McCarville, T J; Miller-Kamm; Rivera, W E; Salmon, J T; Severyn, J R; Thompson, C E; V J; Wang, D Y; Zacharias, R A

    1999-07-01

    The NIF laser system will be capable of delivering 1.8MJ of 351nm energy in 192 beams. Diagnostics instruments must measure beam energy, power vs. time, wavefront quality, and beam intensity profile to characterize laser performance. Alignment and beam diagnostics are also used to set the laser up for the high power shots and to isolate problems when performance is less than expected. Alignment and beam diagnostics are multiplexed to keep the costs under control. At the front-end the beam is aligned and diagnosed in an input sensor package. The output 1053nm beam is sampled by collecting a 0.1% reflection from an output beam sampler and directing it to the output sensor package (OSP). The OSP also gets samples from final focus lens reflection and samples from the transport spatial filter pinhole plane. The output 351nm energy is measured by a calorimeter collecting the signal from an off-axis diffractive beam-sampler. Detailed information on the focused beam in the high-energy target focal plane region is gathered in the precision diagnostics. This paper describes the design of the alignment and diagnostics on the NIF laser system.

  7. Maintenance study for W-340 Waste Retrieval System

    SciTech Connect

    Christensen, C.; Conner, C.C.; Sekot, J.P.

    1994-05-01

    This study was performed to identify attributes and maintainability requirements for the Tank Waste Retrieval System (TWRS). The system will be developed for Westinghouse Hanford Company in Richland, Washington, as an integrated system to perform waste removal in Tank C-106 and, thus, demonstrate technologies for tank remediation that will satisfy requirements of the Tri-Party Agreement. The study examines attributes of the TWRS, scope of maintenance operations required for the TWRS, maintenance requirements, and potential methods of performing maintenance functions. Recommendations are provided for consideration in the development of both the conceptual design and performance specification, which will be used in procuring the W-340 Waste Retrieval System.

  8. Monitoring Strategies in Permeable Pavement Systems to Optimize Maintenance Scheduling

    EPA Science Inventory

    As the surface in a permeable pavement system clogs and performance decreases, maintenance is required to preserve the design function. Currently, guidance is limited for scheduling maintenance on an as needed basis. Previous research has shown that surface clogging in a permea...

  9. Fluid Power Systems Maintenance and Operation. Instructor's Guide.

    ERIC Educational Resources Information Center

    Paule, Bob A.

    Written to complement the Fluid Power/Basic Hydraulic and Basic Pneumatics guides, this curriculum guide contains materials for a seven-unit course in fluid power systems maintenance and operation. Units, which consist of one to eight lessons, cover these topics: preventive maintenance, repair machine malfunctions, overhaul/recondition hydraulic…

  10. Maintenance of Surface Current Balance by Field-Aligned Thermoelectric Currents at Astronomical Bodies: Cassini at Rhea

    NASA Astrophysics Data System (ADS)

    Teolis, B. D.

    2014-12-01

    Cassini spacecraft magnetic field data at Saturn's moon Rhea reveal a field-aligned electric current system in the flux tube, which forms to satisfy the requirement to balance ion and electron currents on the moon's sharp surface. Unlike induction currents at bodies surrounded by significant atmospheres, Rhea's flux tube current system is not driven by motion through the plasma, but rather thermoelectrically, by heat flow into the object. In addition to Rhea, the requirements for the current system are easily satisfied at many plasma absorbing bodies: (1) a difference of average ion and electron gyroradii radii, and (2) a "sharp" body of any size, i.e., without a significant thick atmosphere. This type of current system is therefore expected to occur generally, e.g. at other airless planetary satellites, asteroids, and even spacecraft; and accordingly, represents a fundamental aspect of the physics of the interaction of astrophysical objects with space plasmas.

  11. State-of-the-art Model M-2 Maintenance System

    SciTech Connect

    Herndon, J.N.; Martin, H.L.; Satterlee, P.E. Jr.; Jelatis, D.G.; Jennrich, C.E.

    1984-04-01

    The Model M-2 Maintenance System is part of an ongoing program within the Consolidated Fuel Reprocessing Program (CFRP) at Oak Ridge National Laboratory (ORNL) to improve remote manipulation technology for future nuclear fuel reprocessing and other remote applications. Techniques, equipment, and guidelines which can improve the efficiency of remote maintenance are being developed. The Model M-2 Maintenance System, installed in the Integrated Equipment Test (IET) Facility at ORNL, provides a complete, integrated remote maintenance system for the demonstration and development of remote maintenance techniques. The system comprises a pair of force-reflecting servomanipulator arms, television viewing, lighting, and auxiliary lifting capabilities, thereby allowing manlike maintenance operations to be executed remotely within the remote cell mockup area in the IET. The Model M-2 Maintenance System incorporates an upgraded version of the proven Central Research Laboratories' Model M servomanipulator. Included are state-of-the-art brushless dc servomotors for improved performance, remotely removable wrist assemblies, geared azimuth drive, and a distributed microprocessor-based digital control system. 5 references, 8 figures.

  12. Ground Software Maintenance Facility (GSMF) system manual

    NASA Technical Reports Server (NTRS)

    Derrig, D.; Griffith, G.

    1986-01-01

    The Ground Software Maintenance Facility (GSMF) is designed to support development and maintenance of spacelab ground support software. THE GSMF consists of a Perkin Elmer 3250 (Host computer) and a MITRA 125s (ATE computer), with appropriate interface devices and software to simulate the Electrical Ground Support Equipment (EGSE). This document is presented in three sections: (1) GSMF Overview; (2) Software Structure; and (3) Fault Isolation Capability. The overview contains information on hardware and software organization along with their corresponding block diagrams. The Software Structure section describes the modes of software structure including source files, link information, and database files. The Fault Isolation section describes the capabilities of the Ground Computer Interface Device, Perkin Elmer host, and MITRA ATE.

  13. Low cost, high performance, self-aligning miniature optical systems

    PubMed Central

    Kester, Robert T.; Christenson, Todd; Kortum, Rebecca Richards; Tkaczyk, Tomasz S.

    2009-01-01

    The most expensive aspects in producing high quality miniature optical systems are the component costs and long assembly process. A new approach for fabricating these systems that reduces both aspects through the implementation of self-aligning LIGA (German acronym for lithographie, galvanoformung, abformung, or x-ray lithography, electroplating, and molding) optomechanics with high volume plastic injection molded and off-the-shelf glass optics is presented. This zero alignment strategy has been incorporated into a miniature high numerical aperture (NA = 1.0W) microscope objective for a fiber confocal reflectance microscope. Tight alignment tolerances of less than 10 μm are maintained for all components that reside inside of a small 9 gauge diameter hypodermic tubing. A prototype system has been tested using the slanted edge modulation transfer function technique and demonstrated to have a Strehl ratio of 0.71. This universal technology is now being developed for smaller, needle-sized imaging systems and other portable point-of-care diagnostic instruments. PMID:19543344

  14. Cask system maintenance in the Federal Waste Management System

    SciTech Connect

    Pope, R.B.; Rennich, M.J.; Medley, L.G.; Attaway, C.R.

    1991-01-01

    In early 1988, in support of the development of the transportation system for the Office of Civilian Radioactive Waste Management System (OCRWM), a feasibility study was undertaken to define a the concept for a stand-alone, green-field'' facility for maintaining the Federal Waste Management System (FWMS) casks. This study provided and initial layout facility design, an estimate of the construction costs, and an acquisition schedule for a Cask Maintenance Facility (CMF). It also helped to define the interfaces between the transportation system and the waste generators, the repository, and a Monitored Retrievable Storage (MRS) facility. The data, design, and estimated costs derived from the study have been organized for use in the total transportation system decision-making process. Most importantly, they also provide a foundation for continuing design and planning efforts. The feasibility study was based on an assumed stand-alone, green-field'' configuration. This design approach provides a comprehensive design evaluation, to guide the development of a cost estimate and to permit flexibility in locating the facility. The following sections provide background information on cask system maintenance, briefly summarizes some of the functional requirements that a CMF must satisfy, provides a physical description of the CMF, briefly discusses the cost and schedule estimates and then reviews the findings of the efforts undertaken since the feasibility study was completed. 15 refs., 3 figs.

  15. String-fluid transition in systems with aligned anisotropic interactions.

    PubMed

    Brandt, P C; Ivlev, A V; Morfill, G E

    2010-06-21

    Systems with aligned anisotropic interactions between particles exhibit numerous phase transitions. A remarkable example of the fluid phase transition occurring in such systems is the formation of particle strings--the so-called "string" or "chain" fluids. We employ an approach based on the Ornstein-Zernike (OZ) equation, which allows us to calculate structural properties of fluids with aligned anisotropic interactions. We show that the string-fluid transition can be associated with the bifurcation of the "isotropic" correlation length into two distinct scales which characterize the longitudinal and transverse order in string fluids and, hence, may be used as a fingerprint of this transition. The comparison of the proposed OZ theory with the Monte Carlo simulations reveals fairly good agreement. PMID:20572736

  16. Improving nuclear plant management effectiveness: Aligning strategy, systems, and people

    SciTech Connect

    Price, K.F.

    1991-11-01

    The effectiveness of any organization requires alignment of the appropriate financial, physical, and human resources. The manager's role is to efficiently utilize the right combination of these resources to achieve organizational objectives. In-depth studies of the nuclear programs of three major investor-owned utilities using a culture assessment process called the communication, values, and rewards (CVR) assessment have shown significant misalignments in those organizations' strategies, systems and people management. The CVR assessment related employees' perceptions of what drives their company's culture with the stated company strategic direction and management philosophies. Specifically, CVR provides a comparison of employee-held work-related values with those desired by management. Data obtained by a CVR assessment can be used to understand organizational misalignment and make changes to bring systems into alignment with corporate strategy and culture.

  17. An Automated Fiber Alignment, Fixing, And Hermetic Sealing System

    NASA Astrophysics Data System (ADS)

    Bargar, Daniel S.

    1989-02-01

    An automated fiber alignment, fixing, and sealing process was developed for optoelectronic devices produced by BT&D Technologies. The products -- transmitters, receivers, etc. -- were developed simultaneously with the process, allowing development of common technologies and submodule "building blocks." This approach has many advantages: sufficient manufacturing volume to justify automation, quick response to new product variations, and uniform quality. This paper describes the development of a patented laser-based manufacturing system for pigtailing optoelectronic devices.

  18. An Automated Fiber Alignment, Fixing, And Hermetic Sealing System

    NASA Astrophysics Data System (ADS)

    Bargar, Daniel S.

    1989-01-01

    An automated fiber alignment, fixing, and sealing process was developed for optoelectronic devices produced by BT&D Technologies. The products -- transmitters, receivers, etc. -- were developed simultaneously with the process, allowing development of common technologies and submodule "building blocks." This approach has many advantages: sufficient manufacturing volume to justify automation, quick response to new product variations, and uniform quality. This paper describes the development of a patented laser-based manufacturing system for pigtailing optoelectronic devices.

  19. Understanding Beam Alignment in a Coherent Lidar System

    NASA Technical Reports Server (NTRS)

    Prasad, Narasimha S.; Roychoudhari, Chandrasekhar

    2015-01-01

    Optical beam alignment in a coherent lidar (or ladar) receiver system plays a critical role in optimizing its performance. Optical alignment in a coherent lidar system dictates the wavefront curvature (phase front) and Poynting vector) matching of the local oscillator beam with the incoming receiver beam on a detector. However, this alignment is often not easy to achieve and is rarely perfect. Furthermore, optical fibers are being increasingly used in coherent lidar system receivers for transporting radiation to achieve architectural elegance. Single mode fibers also require stringent mode matching for efficient light coupling. The detector response characteristics vary with the misalignment of the two pointing vectors. Misalignment can lead to increase in DC current. Also, a lens in front of the detector may exasperate phase front and Poynting vector mismatch. Non-Interaction of Waves, or the NIW property indicates the light beams do not interfere by themselves in the absence of detecting dipoles. In this paper, we will analyze the extent of misalignment on the detector specifications using pointing vectors of mixing beams in light of the NIW property.

  20. Utility-scale system preventive and failure-related maintenance

    SciTech Connect

    Jennings, C.; Hutchinson, P.

    1995-11-01

    This paper describes the design and performance background on PVUSA utility-scale systems at Davis and Kerman, California, and reports on a preventative and failure-related maintenance approach and costs.

  1. MAINTENANCE MANAGEMENT ACCOUNTING SYSTEM OF WASTE WATER DISPOSAL SYSTEMS

    NASA Astrophysics Data System (ADS)

    Hori, Michihiro; Tsuruta, Takashi; Kaito, Kiyoyuki; Kobayashi, Kiyoshi

    Sewage works facilities consist of various assets groups. And there are many kinds of financial resources. In order to optimize the maintenance plan, and to secure the stability and sustainability of sewage works management, it is necessary to carry out financial simulation based on the life-cycle cost analysis. Furthermore, it is important to develop management accounting system that is interlinked with the financial accounting system, because many sewage administration bodies have their financial accounting systems as public enterprises. In this paper, a management accounting system, which is designed to provide basic information for asset management of sewage works facilities, is presented. Also the applicability of the management accounting system presented in this paper is examined through financial simulations.

  2. An active alignment method for post launch co-alignment of laser beam combiner systems

    NASA Technical Reports Server (NTRS)

    Yu, A. W.; Green, J. W.; Maynard, W. L.; Minott, P. O.; Krainak, M. A.

    1992-01-01

    A laser transmitter for high bandwidth geosynchronous satellite communications is described. High optical power is achieved by combining semiconductor laser diodes. An active alignment scheme is proposed for achieving the +/- 20 microrad post launch multiple laser angular co-alignment requirement.

  3. National Ignition Facility sub-system design requirements automatic alignment system SSDR 1.5.5

    SciTech Connect

    VanArsdall, P.; Bliss, E.

    1996-09-01

    This System Design Requirement document establishes the performance, design, development, and test requirements for the Automatic Alignment System, which is part of the NIF Integrated Computer Control System (ICCS).

  4. System and method for 2D workpiece alignment

    SciTech Connect

    Weaver, William T.; Carlson, Charles T.; Smith, Scott A.; Beck, Michael A.; Webb, Aaron P.; Strassner, James D.; Gravell, Lawrence R.; Simmons, Michael C.

    2015-07-14

    A carrier capable of holding one or more workpieces is disclosed. The carrier includes movable projections located along the sides of each cell in the carrier. This carrier, in conjunction with a separate alignment apparatus, aligns each workpiece within its respective cell against several alignment pins, using a multiple step alignment process to guarantee proper positioning of the workpiece in the cell. First, the workpieces are moved toward one side of the cell. Once the workpieces have been aligned against this side, the workpieces are then moved toward an adjacent orthogonal side such that the workpieces are aligned to two sides of the cell. Once aligned, the workpiece is held in place by the projections located along each side of each cell. In addition, the alignment pins are also used to align the associated mask, thereby guaranteeing that the mask is properly aligned to the workpiece.

  5. Automatic Alignment System for the National Ignition Facility

    SciTech Connect

    Wilhlelmsen, K C; Awwal, A S; Ferguson, S W; Horowitz, B; Miller Kamm, V J; Reynolds, C A

    2007-10-04

    The automatic alignment system for the National Ignition Facility (NIF) is a large-scale parallel system that directs all 192 laser beams along the 300-m optical path to a 50-micron focus at target chamber in less than 30 minutes. The system commands 9,000 stepping motors to adjust mirrors and other optics. Twenty-two control loops per beamline request image processing services running on a LINUX cluster to analyze high-resolution images of the beam and references. Process-leveling assures the computational load is evenly spread on the cluster. Algorithms also estimate measurement accuracy and reject off-normal images. One challenge to achieving rapid alignment of beams in parallel is the efficient coordination of shared laser devices, such as sensors that are configurable to monitor multiple beams. Contention for shared resources is managed by the Component Mediation System, which precludes deadlocks and optimizes device motions using a hierarchical component structure. A reservation service provided by the software framework prevents interference from competing instances of automated controls or from the actions of system operators. The design, architecture and performance of the system will be discussed.

  6. Development of plant maintenance management system (pmms): a case study

    NASA Astrophysics Data System (ADS)

    Che Azhar, N. A.; Mansor, M. A.

    2013-12-01

    In large plant industry, it is not easy to maintain machine performance without using any method such as checklist system. Manual checklist is a common maintenance checklist used in industry. All machine, equipment and parts that need to be checked will be written down for the employee to do maintenance checks. Converting the manual checklist to the Plant Maintenance Management System (PMMS) can improve the way of employees work and make plant management easier. Therefore, a new system was designed to maintain the equipment so that the activities are more efficient and cost effective. The system consists of three frames that connect to each other. The frames divide to section, equipment and checklist. This system also builds to prevent data from arbitrarily changes. Only certain officers or staffs are permitted to make modifications to data. Using this system, a company can make the office environment a paperless environment.

  7. MACSIMS : multiple alignment of complete sequences information management system

    PubMed Central

    Thompson, Julie D; Muller, Arnaud; Waterhouse, Andrew; Procter, Jim; Barton, Geoffrey J; Plewniak, Frédéric; Poch, Olivier

    2006-01-01

    Background In the post-genomic era, systems-level studies are being performed that seek to explain complex biological systems by integrating diverse resources from fields such as genomics, proteomics or transcriptomics. New information management systems are now needed for the collection, validation and analysis of the vast amount of heterogeneous data available. Multiple alignments of complete sequences provide an ideal environment for the integration of this information in the context of the protein family. Results MACSIMS is a multiple alignment-based information management program that combines the advantages of both knowledge-based and ab initio sequence analysis methods. Structural and functional information is retrieved automatically from the public databases. In the multiple alignment, homologous regions are identified and the retrieved data is evaluated and propagated from known to unknown sequences with these reliable regions. In a large-scale evaluation, the specificity of the propagated sequence features is estimated to be >99%, i.e. very few false positive predictions are made. MACSIMS is then used to characterise mutations in a test set of 100 proteins that are known to be involved in human genetic diseases. The number of sequence features associated with these proteins was increased by 60%, compared to the features available in the public databases. An XML format output file allows automatic parsing of the MACSIM results, while a graphical display using the JalView program allows manual analysis. Conclusion MACSIMS is a new information management system that incorporates detailed analyses of protein families at the structural, functional and evolutionary levels. MACSIMS thus provides a unique environment that facilitates knowledge extraction and the presentation of the most pertinent information to the biologist. A web server and the source code are available at . PMID:16792820

  8. Fabrication and Alignment of Parts of the KASINICS Offner System

    NASA Astrophysics Data System (ADS)

    Mok, Seungwon; Lee, Sungho; Yuk, In-Soo; Park, Youngsik; Jin, Ho; Han, Jeong-Yeol; Moon, Bongkon; Cha, Sang-Mok; Kim, Geon Hee; Im, Myungshin

    2006-12-01

    The KASINICS (KASI Near Infrared Camera System) is a ground-based Near-Infrared (NIR) imaging instrument developed by the Korean Astronomy and Space Science Institute (KASI). In this paper, we report the test results of the KASINICS camera optics system which is comprised of a 1-1 Offner relay. We measure that the surface RMS fluctuations of the Offner mirrors are at the level of 10-1 - 10-2 of the target wavelengths, showing that the mirrors are sufficiently smooth for NIR observations. The alignment of the Offner optics system has been checked too. Our ray-tracing simulations find that the image quality should not degrade more than the pixel size of the KASINICS (40 μm), if a de-centering or a tilt of the Offner mirrors are within 5 mm, or 2.5 °. Our measurement shows that the de-centering or the tilt of the Offner mirrors are less than 1 mm or 0.5 °, assuring that the KASINICS image quality are not affected by the alignment errors. We have also measured that the optics resolution is 20 μm and it does not degrade more than 10 % over the detector surface area of 14.3 mm × 14.3 mm. Overall, we conclude that the KASINICS optics system satisfies the design requirements for NIR imaging observations.

  9. Method and system for aligning fibers during electrospinning

    NASA Technical Reports Server (NTRS)

    Scott-Carnell, Lisa A. (Inventor); Stephens, Ralph M (Inventor); Holloway, Nancy M. (Inventor); Rhim, Caroline (Inventor); Niklason, Laura (Inventor); Clark, Robert L. (Inventor); Siochi, Emilie J. (Inventor)

    2011-01-01

    A method and system are provided for aligning fibers in an electrospinning process. A jet of a fiberizable material is directed towards an uncharged collector from a dispensing location that is spaced apart from the collector. While the fiberizable material is directed towards the collector, an elliptical electric field is generated via the electrically charged dispenser and an oppositely-charged control location. The field spans between the dispensing location and the control location that is within line-of-sight of the dispensing location, and impinges upon at least a portion of the collector. Various combinations of numbers and geometries of dispensers, collectors, and electrodes can be used.

  10. Study of turboprop systems reliability and maintenance costs

    NASA Technical Reports Server (NTRS)

    1978-01-01

    The overall reliability and maintenance costs (R&MC's) of past and current turboprop systems were examined. Maintenance cost drivers were found to be scheduled overhaul (40%), lack of modularity particularly in the propeller and reduction gearbox, and lack of inherent durability (reliability) of some parts. Comparisons were made between the 501-D13/54H60 turboprop system and the widely used JT8D turbofan. It was found that the total maintenance cost per flight hour of the turboprop was 75% higher than that of the JT8D turbofan. Part of this difference was due to propeller and gearbox costs being higher than those of the fan and reverser, but most of the difference was in the engine core where the older technology turboprop core maintenance costs were nearly 70 percent higher than for the turbofan. The estimated maintenance cost of both the advanced turboprop and advanced turbofan were less than the JT8D. The conclusion was that an advanced turboprop and an advanced turbofan, using similar cores, will have very competitive maintenance costs per flight hour.

  11. Alignment and focusing device for a multibeam laser system

    SciTech Connect

    Sweatt, W.C.

    1980-01-01

    Large inertial confinement fusion laser systems have many beams focusing on a small target. The Antares system is a 24-beam CO/sub 2/ pulse laser. To produce uniform illumination, the 24 beams must be individually focused on (or near) the target's surface in a symmetric pattern. To assess the quality of a given beam, we will locate a Smartt (point diffraction) interferometer at the desired focal point and illuminate it with an alignment laser. The resulting fringe pattern shows defocus, lateral misalignment, and beam aberrations; all of which can be minimized by tilting and translating the focusing mirror and the preceding flat mirror. The device described in this paper will remotely translate the Smartt interferometer to any position in the target space and point it in any direction using a two-axis gimbal. The fringes produced by the interferometer are relayed out of the target vacuum shell to a vidicon by a train or prisms. We are designing four separate snap-in heads to mount on the gimbal; two of which are Smartt interferometers (for 10.6 ..mu..m and 633 nm) and two for pinholes, should we wish to put an alignment beam backwards through the system.

  12. Time maintenance system for the BMDO MSX spacecraft

    NASA Technical Reports Server (NTRS)

    Hermes, Martin J.

    1994-01-01

    The Johns Hopkins University Applied Physics Laboratory (APL) is responsible for designing and implementing a clock maintenance system for the Ballistic Missile Defense Organizations (BMDO) Midcourse Space Experiment (MSX) spacecraft. The MSX spacecraft has an on-board clock that will be used to control execution of time-dependent commands and to time tag all science and housekeeping data received from the spacecraft. MSX mission objectives have dictated that this spacecraft time, UTC(MSX), maintain a required accuracy with respect to UTC(USNO) of +/- 10 ms with a +/- 1 ms desired accuracy. APL's atomic time standards and the downlinked spacecraft time were used to develop a time maintenance system that will estimate the current MSX clock time offset during an APL pass and make estimates of the clock's drift and aging using the offset estimates from many passes. Using this information, the clock's accuracy will be maintained by uplinking periodic clock correction commands. The resulting time maintenance system is a combination of offset measurement, command/telemetry, and mission planning hardware and computing assets. All assets provide necessary inputs for deciding when corrections to the MSX spacecraft clock must be made to maintain its required accuracy without inhibiting other mission objectives. The MSX time maintenance system is described as a whole and the clock offset measurement subsystem, a unique combination of precision time maintenance and measurement hardware controlled by a Macintosh computer, is detailed. Simulations show that the system estimates the MSX clock offset to less than+/- 33 microseconds.

  13. Optimal maintenance of a multi-unit system under dependencies

    NASA Astrophysics Data System (ADS)

    Sung, Ho-Joon

    The availability, or reliability, of an engineering component greatly influences the operational cost and safety characteristics of a modern system over its life-cycle. Until recently, the reliance on past empirical data has been the industry-standard practice to develop maintenance policies that provide the minimum level of system reliability. Because such empirically-derived policies are vulnerable to unforeseen or fast-changing external factors, recent advancements in the study of topic on maintenance, which is known as optimal maintenance problem, has gained considerable interest as a legitimate area of research. An extensive body of applicable work is available, ranging from those concerned with identifying maintenance policies aimed at providing required system availability at minimum possible cost, to topics on imperfect maintenance of multi-unit system under dependencies. Nonetheless, these existing mathematical approaches to solve for optimal maintenance policies must be treated with caution when considered for broader applications, as they are accompanied by specialized treatments to ease the mathematical derivation of unknown functions in both objective function and constraint for a given optimal maintenance problem. These unknown functions are defined as reliability measures in this thesis, and theses measures (e.g., expected number of failures, system renewal cycle, expected system up time, etc.) do not often lend themselves to possess closed-form formulas. It is thus quite common to impose simplifying assumptions on input probability distributions of components' lifetime or repair policies. Simplifying the complex structure of a multi-unit system to a k-out-of-n system by neglecting any sources of dependencies is another commonly practiced technique intended to increase the mathematical tractability of a particular model. This dissertation presents a proposal for an alternative methodology to solve optimal maintenance problems by aiming to achieve the

  14. A dual purpose optical truss laser metrology system for a space-based far-IR segmented telescope: Figure maintenance and pointing control

    NASA Technical Reports Server (NTRS)

    Lau, Kenneth

    1992-01-01

    To obtain imaging performance as for monolithic mirrors, large segmented reflectors used for astronomy must be actively aligned and pointed to extreme levels of precision. A system concept for a dual purpose optical truss laser metrology system is described which is used for both figure and alignment maintenance and telescope pointing. A two-stage figure active control approach was developed for several proposed spaceborne far infrared segmented telescopes, one of which is the 10-20 meters Large Deployable Reflector (LDR). The first active control stage, the figure initialization control system, aligns the optical elements (i.e., the primary segments, secondary and focal plane assembly) based on images obtained. The second stage, the figure maintenance control system, maintains the alignment between re-initializations using measurements provided by laser interferometers arranged in an optical truss configuration. It measures the relative positions and alignments of the telescope segments so that a controller can reposition them appropriately. The application of this optical truss for figure maintenance control is the subject of the first part of this paper. The second portion of this paper discusses the application of the optical truss to telescope pointing. Here, the laser metrology system is used to transfer pointing information from an external fine guidance sensor (FGS) to the telescope optical boresight as defined by the primary mirror, secondary mirror, and focal plane assembly. Thus, any alignment variations between the two boresights can be observed and accounted for.

  15. Energy: Systems for Control, Maintenance, and Storage. A Bibliography.

    ERIC Educational Resources Information Center

    Thomas, Gerald, Comp.; McKane, Irving, Comp.

    This publication is a bibliography of available periodical literature on specific aspects of energy and today's technology. The Applied Science and Technology Indexes were searched for articles that related to these specific areas: (1) Energy control systems; (2) Maintenance of Energy Systems; and (3) Energy storage. The articles and papers…

  16. Cradle/pump heating system operation and maintenance manual

    SciTech Connect

    Taylor, S.L., Fluor Daniel Hanford

    1997-02-01

    This is the operation and maintenance manual for the 241-SY-101 Cradle/Pump Heating System. The Heating System provides the means to heat the pump (HMT {number_sign}2) during cold weather to assure safe and smooth pump installation.

  17. 14 CFR 121.1113 - Fuel tank system maintenance program.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Instructions for Continued Airworthiness (ICA) that have been developed in accordance with the applicable... tank ICA are developed under SFAR 88 or under § 25.1529 in effect on June 6, 2001, the certificate... tank system based on those ICA. (f) The fuel tank system maintenance program changes identified...

  18. 14 CFR 121.1113 - Fuel tank system maintenance program.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Instructions for Continued Airworthiness (ICA) that have been developed in accordance with the applicable... tank ICA are developed under SFAR 88 or under § 25.1529 in effect on June 6, 2001, the certificate... tank system based on those ICA. (f) The fuel tank system maintenance program changes identified...

  19. Document creation, linking, and maintenance system

    DOEpatents

    Claghorn, Ronald

    2011-02-15

    A document creation and citation system designed to maintain a database of reference documents. The content of a selected document may be automatically scanned and indexed by the system. The selected documents may also be manually indexed by a user prior to the upload. The indexed documents may be uploaded and stored within a database for later use. The system allows a user to generate new documents by selecting content within the reference documents stored within the database and inserting the selected content into a new document. The system allows the user to customize and augment the content of the new document. The system also generates citations to the selected content retrieved from the reference documents. The citations may be inserted into the new document in the appropriate location and format, as directed by the user. The new document may be uploaded into the database and included with the other reference documents. The system also maintains the database of reference documents so that when changes are made to a reference document, the author of a document referencing the changed document will be alerted to make appropriate changes to his document. The system also allows visual comparison of documents so that the user may see differences in the text of the documents.

  20. Liquid sodium dip seal maintenance system

    DOEpatents

    Briggs, Richard L.; Meacham, Sterling A.

    1980-01-01

    A system for spraying liquid sodium onto impurities associated with liquid dip seals of nuclear reactors. The liquid sodium mixing with the impurities dissolves the impurities in the liquid sodium. The liquid sodium having dissolved and diluted the impurities carries the impurities away from the site thereby cleaning the liquid dip seal and surrounding area. The system also allows wetting of the metallic surfaces of the dip seal thereby reducing migration of radioactive particles across the wetted boundary.

  1. Building Systems Diagnostics and Predictive Maintenance

    SciTech Connect

    Katipamula, Srinivas; Pratt, Robert G.; Braun, J.

    2001-01-01

    There has been an increasing interest in the development of methods and tools for automated fault detection and diagnostics (FDD) of building systems and components in the 1990s. This chapter, written for the CRC Handbook for HVAC&R Engineering, will describe the status of these methods and and methodologies as applied to HVAC&R and building systems and present certain illustrative case studies.

  2. Optimal maintenance center inventories for fault-tolerant repairable systems

    NASA Technical Reports Server (NTRS)

    Lawrence, S. H.; Schaefer, M. K.

    1984-01-01

    A probabilistic approach is taken to determine the optimal repairable parts inventory for a maintenance center, servicing machines which contain several m-out-of-n systems of different parts, with a constraint on the total inventory investment. A model, based on the discrete Markov process, accounts for a typical ultrareliable avionics system, such as one presently being developed by NASA. The dynamic programming algorithm for minimizing the stockout and holding costs is applied to an exemplary maintenance center, and solutions for single-item and multi-item cases are given. The computational burden is noted to be reasonable and a computer program is used to generate optimal solutions.

  3. Informed maintenance for next generation reusable launch systems

    NASA Astrophysics Data System (ADS)

    Fox, Jack J.; Gormley, Thomas J.

    2001-03-01

    Perhaps the most substantial single obstacle to progress of space exploration and utilization of space for human benefit is the safety & reliability and the inherent cost of launching to, and returning from, space. The primary influence in the high costs of current launch systems (the same is true for commercial and military aircraft and most other reusable systems) is the operations, maintenance and infrastructure portion of the program's total life cycle costs. Reusable Launch Vehicle (RLV) maintenance and design have traditionally been two separate engineering disciplines with often conflicting objectives - maximizing ease of maintenance versus optimizing performance, size and cost. Testability analysis, an element of Informed Maintenance (IM), has been an ad hoc, manual effort, in which maintenance engineers attempt to identify an efficient method of troubleshooting for the given product, with little or no control over product design. Therefore, testability deficiencies in the design cannot be rectified. It is now widely recognized that IM must be engineered into the product at the design stage itself, so that an optimal compromise is achieved between system maintainability and performance. The elements of IM include testability analysis, diagnostics/prognostics, automated maintenance scheduling, automated logistics coordination, paperless documentation and data mining. IM derives its heritage from complimentary NASA science, space and aeronautic enterprises such as the on-board autonomous Remote Agent Architecture recently flown on NASA's Deep Space 1 Probe as well as commercial industries that employ quick turnaround operations. Commercial technologies and processes supporting NASA's IM initiatives include condition based maintenance technologies from Boeing's Commercial 777 Aircraft and Lockheed-Martin's F-22 Fighter, automotive computer diagnostics and autonomous controllers that enable 100,000 mile maintenance free operations, and locomotive monitoring

  4. Informed maintenance for next generation space transportation systems

    NASA Astrophysics Data System (ADS)

    Fox, Jack J.

    2001-02-01

    Perhaps the most substantial single obstacle to progress of space exploration and utilization of space for human benefit is the safety & reliability and the inherent cost of launching to, and returning from, space. The primary influence in the high costs of current launch systems (the same is true for commercial and military aircraft and most other reusable systems) is the operations, maintenance and infrastructure portion of the program's total life cycle costs. Reusable Launch Vehicle (RLV) maintenance and design have traditionally been two separate engineering disciplines with often conflicting objectives-maximizing ease of maintenance versus optimizing performance, size and cost. Testability analysis, an element of Informed Maintenance (IM), has been an ad hoc, manual effort, in which maintenance engineers attempt to identify an efficient method of troubleshooting for the given product, with little or no control over product design. Therefore, testability deficiencies in the design cannot be rectified. It is now widely recognized that IM must be engineered into the product at the design stage itself, so that an optimal compromise is achieved between system maintainability and performance. The elements of IM include testability analysis, diagnostics/prognostics, automated maintenance scheduling, automated logistics coordination, paperless documentation and data mining. IM derives its heritage from complimentary NASA science, space and aeronautic enterprises such as the on-board autonomous Remote Agent Architecture recently flown on NASA's Deep Space 1 Probe as well as commercial industries that employ quick turnaround operations. Commercial technologies and processes supporting NASA's IM initiatives include condition based maintenance technologies from Boeing's Commercial 777 Aircraft and Lockheed-Martin's F-22 Fighter, automotive computer diagnostics and autonomous controllers that enable 100,000 mile maintenance free operations, and locomotive monitoring

  5. Augmented Reality System for E-maintenance Application

    NASA Astrophysics Data System (ADS)

    Benbelkacem, S.; Zenati-Henda, N.; Belhocine, M.; Malek, S.

    2009-03-01

    We present in this paper an Augmented Reality platform for e-maintenance application. In our case, the aim is not to develop a vision system based on augmented reality concept, but to show the relationship between the different actors in the proposed architecture and to facilitate maintenance of the machine. With this platform we identify all possible scenarios which allow the technician to intervene on a machine breakdown using distant expert if necessary. Each scenario depends on the machine parameters and the technician competences. To implement a configuration of Augmented Reality system, we chose a case study of maintenance scenario for machine breakdown. Then we represent this scenario by an interaction model which allows establishing Augmented Reality configuration.

  6. 75 FR 65052 - Consensus Standards, Standard Practice for Maintenance of Airplane Electrical Wiring Systems

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-10-21

    ... TRANSPORTATION Federal Aviation Administration Consensus Standards, Standard Practice for Maintenance of Airplane... Practice for Maintenance of Airplane Electrical Wiring Systems (Standard Practice) as an acceptable means... FAA finds the standards to be acceptable methods and procedures for maintenance of electrical...

  7. Index : A Rule Based Expert System For Computer Network Maintenance

    NASA Astrophysics Data System (ADS)

    Chaganty, Srinivas; Pitchai, Anandhi; Morgan, Thomas W.

    1988-03-01

    Communications is an expert intensive discipline. The application of expert systems for maintenance of large and complex networks, mainly as an aid in trouble shooting, can simplify the task of network management. The important steps involved in troubleshooting are fault detection, fault reporting, fault interpretation and fault isolation. At present, Network Maintenance Facilities are capable of detecting and reporting the faults to network personnel. Fault interpretation refers to the next step in the process, which involves coming up with reasons for the failure. Fault interpretation can be characterized in two ways. First, it involves such a diversity of facts that it is difficult to predict. Secondly, it embodies a wealth of knowledge in the form of network management personnel. The application of expert systems in these interpretive tasks is an important step towards automation of network maintenance. In this paper, INDEX (Intelligent Network Diagnosis Expediter), a rule based production system for computer network alarm interpretation is described. It acts as an intelligent filter for people analyzing network alarms. INDEX analyzes the alarms in the network and identifies proper maintenance action to be taken.The important feature of this production system is that it is data driven. Working memory is the principal data repository of production systems and its contents represent the current state of the problem. Control is based upon which productions match the constantly changing working memory elements. Implementation of the prototype is in OPS83. Major issues in rule based system development such as rule base organization, implementation and efficiency are discussed.

  8. Advanced Ground Systems Maintenance Prognostics Project

    NASA Technical Reports Server (NTRS)

    Harp, Janicce Leshay

    2014-01-01

    The project implements prognostics capabilities to predict when a component, system or subsystem will no longer meet desired functional or performance criteria, called the "end of life." The capability also provides an assessment of the "remaining useful life" of a hardware component.

  9. Performance management system enhancement and maintenance

    NASA Technical Reports Server (NTRS)

    Cleaver, T. G.; Ahour, R.; Johnson, B. R.

    1984-01-01

    The research described in this report concludes a two-year effort to develop a Performance Management System (PMS) for the NCC computers. PMS provides semi-automated monthly reports to NASA and contractor management on the status and performance of the NCC computers in the TDRSS program. Throughout 1984, PMS was tested, debugged, extended, and enhanced. Regular PMS monthly reports were produced and distributed. PMS continues to operate at the NCC under control of Bendix Corp. personnel.

  10. Heat transfer in vertically aligned phase change energy storage systems

    SciTech Connect

    El-Dessouky, H.T.; Bouhamra, W.S.; Ettouney, H.M.; Akbar, M.

    1999-05-01

    Convection effects on heat transfer are analyzed in low temperature and vertically aligned phase change energy storage systems. This is performed by detailed temperature measurements in the phase change material (PCM) in eighteen locations forming a grid of six radial and three axial positions. The system constitutes a double pipe configuration, where commercial grade paraffin wax is stored in the annular space between the two pipes and water flows inside the inner pipe. Vertical alignment of the system allowed for reverse of the flow direction of the heat transfer fluid (HTF), which is water. Therefore, the PCM is heated from the bottom for HTF flow from bottom to top and from the top as the HTF flow direction is reversed. For the former case, natural convection affects the melting process. Collected data are used to study variations in the transient temperature distribution at axial and radial positions as well as for the two-dimensional temperature field. The data are used to calculate the PCM heat transfer coefficient and to develop correlations for the melting Fourier number. Results indicate that the PCM heat transfer coefficient is higher for the case of PCM heating from bottom to top. Nusselt number correlations are developed as a function of Rayleigh, Stefan, and Fourier numbers for the HTF flow from bottom to top and as a function of Stefan and Fourier numbers for HTF flow from top to bottom. The enhancement ratio for heat transfer caused by natural convection increases and then levels off as the inlet temperature of the HTF is increased.

  11. NIF pointing and centering systems and target alignment using a 351 nm laser source

    SciTech Connect

    Boege, S.J.; Bliss, E.S.; Chocol, C.J.; Holdener, F.R.; Miller, J.L.; Toeppen, J.S.; Vann, C.S.; Zacharias, R.A.

    1996-10-01

    The operational requirements of the National Ignition Facility (NIF) place tight constraints upon its alignment system. In general, the alignment system must establish and maintain the correct relationships between beam position, beam angle, laser component clear apertures, and the target. At the target, this includes adjustment of beam focus to obtain the correct spot size. This must be accomplished for all beamlines in a time consistent with planned shot rates and yet, in the front end and main laser, beam control functions cannot be initiated until the amplifiers have sufficiently cooled so as to minimize dynamic thermal distortions during and after alignment and wavefront optimization. The scope of the task dictates an automated system that implements parallel processes. We describe reticle choices and other alignment references, insertion of alignment beams, principles of operation of the Chamber Center Reference System 2048 and Target Alignment Sensor, and the anticipated alignment sequence that will occur between shots.

  12. Systems Maintenance Automated Repair Tasks (SMART)

    NASA Technical Reports Server (NTRS)

    2008-01-01

    SMART is an interactive decision analysis and refinement software system that uses evaluation criteria for discrepant conditions to automatically provide and populate a document/procedure with predefined steps necessary to repair a discrepancy safely, effectively, and efficiently. SMART can store the tacit (corporate) knowledge merging the hardware specification requirements with the actual "how to" repair methods, sequences, and required equipment, all within a user-friendly interface. Besides helping organizations retain repair knowledge in streamlined procedures and sequences, SMART can also help them in saving processing time and expense, increasing productivity, improving quality, and adhering more closely to safety and other guidelines. Though SMART was developed for Space Shuttle applications, its interface is easily adaptable to any hardware that can be broken down by component, subcomponent, discrepancy, and repair.

  13. Teleoperated systems for nuclear reactors: Inspection and maintenance

    NASA Technical Reports Server (NTRS)

    Dorokhov, V. P.; Dorokhov, D. V.; Eperin, A. P.

    1994-01-01

    The present paper describes author's work in the field of teleoperated equipment for inspection and maintenance of the RBML technological channels and graphite laying, emergency operations. New technological and design solutions of teleoperated robotic systems developed for Leningradsky Power Plant are discussed.

  14. Systems Maintenance Automated Repair Tasks (SMART)

    NASA Technical Reports Server (NTRS)

    Schuh, Joseph; Mitchell, Brent; Locklear, Louis; Belson, Martin A.; Al-Shihabi, Mary Jo Y.; King, Nadean; Norena, Elkin; Hardin, Derek

    2010-01-01

    SMART is a uniform automated discrepancy analysis and repair-authoring platform that improves technical accuracy and timely delivery of repair procedures for a given discrepancy (see figure a). SMART will minimize data errors, create uniform repair processes, and enhance the existing knowledge base of engineering repair processes. This innovation is the first tool developed that links the hardware specification requirements with the actual repair methods, sequences, and required equipment. SMART is flexibly designed to be useable by multiple engineering groups requiring decision analysis, and by any work authorization and disposition platform (see figure b). The organizational logic creates the link between specification requirements of the hardware, and specific procedures required to repair discrepancies. The first segment in the SMART process uses a decision analysis tree to define all the permutations between component/ subcomponent/discrepancy/repair on the hardware. The second segment uses a repair matrix to define what the steps and sequences are for any repair defined in the decision tree. This segment also allows for the selection of specific steps from multivariable steps. SMART will also be able to interface with outside databases and to store information from them to be inserted into the repair-procedure document. Some of the steps will be identified as optional, and would only be used based on the location and the current configuration of the hardware. The output from this analysis would be sent to a work authoring system in the form of a predefined sequence of steps containing required actions, tools, parts, materials, certifications, and specific requirements controlling quality, functional requirements, and limitations.

  15. Concept of a programmable maintenance processor applicable to multiprocessing systems

    NASA Technical Reports Server (NTRS)

    Glover, Richard D.

    1988-01-01

    A programmable maintenance processor concept applicable to multiprocessing systems has been developed at the NASA Ames Research Center's Dryden Flight Research Facility. This stand-alone-processor is intended to provide support for system and application software testing as well as hardware diagnostics. An initial machanization has been incorporated into the extended aircraft interrogation and display system (XAIDS) which is multiprocessing general-purpose ground support equipment. The XAIDS maintenance processor has independent terminal and printer interfaces and a dedicated magnetic bubble memory that stores system test sequences entered from the terminal. This report describes the hardware and software embodied in this processor and shows a typical application in the check-out of a new XAIDS.

  16. CLASSIFICATION OF THE MGR MAINTENANCE AND SUPPLY SYSTEM

    SciTech Connect

    J.A. Ziegler

    1999-08-31

    The purpose of this analysis is to document the Quality Assurance (QA) classification of the Monitored Geologic Repository (MGR) maintenance and supply system structures, systems and components (SSCs) performed by the MGR Safety Assurance Department. This analysis also provides the basis for revision of YMP/90-55Q, Q-List (YMP 1998). The Q-List identifies those MGR SSCs subject to the requirements of DOE/RW-0333P, ''Quality Assurance Requirements and Description'' (QARD) (DOE 1998).

  17. Portable Knowledge-Based Diagnostic And Maintenance Systems

    NASA Astrophysics Data System (ADS)

    Darvish, John; Olson, Noreen S.

    1989-03-01

    It is difficult to diagnose faults and maintain weapon systems because (1) they are highly complex pieces of equipment composed of multiple mechanical, electrical, and hydraulic assemblies, and (2) talented maintenance personnel are continuously being lost through the attrition process. To solve this problem, we developed a portable diagnostic and maintenance aid that uses a knowledge-based expert system. This aid incorporates diagnostics, operational procedures, repair and replacement procedures, and regularly scheduled maintenance into one compact, 18-pound graphics workstation. Drawings and schematics can be pulled up from the CD-ROM to assist the operator in answering the expert system's questions. Work for this aid began with the development of the initial knowledge-based expert system in a fast prototyping environment using a LISP machine. The second phase saw the development of a personal computer-based system that used videodisc technology to pictorially assist the operator. The current version of the aid eliminates the high expenses associated with videodisc preparation by scanning in the art work already in the manuals. A number of generic software tools have been developed that streamlined the construction of each iteration of the aid; these tools will be applied to the development of future systems.

  18. A beginner's guide to belief revision and truth maintenance systems

    NASA Technical Reports Server (NTRS)

    Mason, Cindy L.

    1992-01-01

    This brief note is intended to familiarize the non-TMS audience with some of the basic ideas surrounding classic TMS's (truth maintenance systems), namely the justification-based TMS and the assumption-based TMS. Topics of further interest include the relation between non-monotonic logics and TMS's, efficiency and search issues, complexity concerns, as well as the variety of TMS systems that have surfaced in the past decade or so. These include probabilistic-based TMS systems, fuzzy TMS systems, tri-valued belief systems, and so on.

  19. Risk-informed Maintenance for Non-coherent Systems

    NASA Astrophysics Data System (ADS)

    Tao, Ye

    Probabilistic Safety Assessment (PSA) is a systematic and comprehensive methodology to evaluate risks associated with a complex engineered technological entity. The information provided by PSA has been increasingly implemented for regulatory purposes but rarely used in providing information for operation and maintenance activities. As one of the key parts in PSA, Fault Tree Analysis (FTA) attempts to model and analyze failure processes of engineering and biological systems. The fault trees are composed of logic diagrams that display the state of the system and are constructed using graphical design techniques. Risk Importance Measures (RIMs) are information that can be obtained from both qualitative and quantitative aspects of FTA. Components within a system can be ranked with respect to each specific criterion defined by each RIM. Through a RIM, a ranking of the components or basic events can be obtained and provide valuable information for risk-informed decision making. Various RIMs have been applied in various applications. In order to provide a thorough understanding of RIMs and interpret the results, they are categorized with respect to risk significance (RS) and safety significance (SS) in this thesis. This has also tied them into different maintenance activities. When RIMs are used for maintenance purposes, it is called risk-informed maintenance. On the other hand, the majority of work produced on the FTA method has been concentrated on failure logic diagrams restricted to the direct or implied use of AND and OR operators. Such systems are considered as coherent systems. However, the NOT logic can also contribute to the information produced by PSA. The importance analysis of non-coherent systems is rather limited, even though the field has received more and more attention over the years. The non-coherent systems introduce difficulties in both qualitative and quantitative assessment of the fault tree compared with the coherent systems. In this thesis, a set

  20. The Feasibility of a Land Ferry System to Reduce Highway Maintenance Cost and Associated Externalities.

    PubMed

    Merrill, Steve J; Paz, Alexander; Molano, Victor; Shrestha, Pramen P; Maheshwari, Pankaj; Stephen, Haroon; de la Fuente-Mella, Hanns

    2016-01-01

    This study provides an economic evaluation for a Land Ferry, which is a rail system capable of carrying trucks and all other types of vehicles, passengers, and cargo. The Land Ferry system involves a sliding loading system to roll heavy loads onto a flatbed; as a result, loading and unloading of all vehicles and cargo could be accomplished simultaneously. The evaluation for this system included (1) the design of a new track alignment over which the Land Ferry system would run, (2) evaluation of various sources of power, (3) estimation of how many local jobs the Land Ferry would generate, and (4) a benefit-cost analysis. It was estimated that the Land Ferry would create over 45,788 temporary jobs in Nevada during the three-year construction period and 318 permanent jobs during operation. The majority of the benefits were attributed to savings in travel time ($356.4 M), vehicle operating costs ($1000.4 M), reduction of accidents ($544.6 M), and pavement maintenance ($503.2 M). These benefits would be a consequence of the shift of trucks from the highway, thus resulting in higher speeds, decrease fuel consumption, and decrease vehicle maintenance costs. The overall benefit-cost ratio of 1.7 implies a cost-effective project. PMID:27419201

  1. The Feasibility of a Land Ferry System to Reduce Highway Maintenance Cost and Associated Externalities

    PubMed Central

    Merrill, Steve J.; Paz, Alexander; Molano, Victor; Shrestha, Pramen P.; Maheshwari, Pankaj; Stephen, Haroon

    2016-01-01

    This study provides an economic evaluation for a Land Ferry, which is a rail system capable of carrying trucks and all other types of vehicles, passengers, and cargo. The Land Ferry system involves a sliding loading system to roll heavy loads onto a flatbed; as a result, loading and unloading of all vehicles and cargo could be accomplished simultaneously. The evaluation for this system included (1) the design of a new track alignment over which the Land Ferry system would run, (2) evaluation of various sources of power, (3) estimation of how many local jobs the Land Ferry would generate, and (4) a benefit-cost analysis. It was estimated that the Land Ferry would create over 45,788 temporary jobs in Nevada during the three-year construction period and 318 permanent jobs during operation. The majority of the benefits were attributed to savings in travel time ($356.4 M), vehicle operating costs ($1000.4 M), reduction of accidents ($544.6 M), and pavement maintenance ($503.2 M). These benefits would be a consequence of the shift of trucks from the highway, thus resulting in higher speeds, decrease fuel consumption, and decrease vehicle maintenance costs. The overall benefit-cost ratio of 1.7 implies a cost-effective project. PMID:27419201

  2. A Concept for Zero-Alignment Micro Optical Systems

    SciTech Connect

    DESCOUR, MICHAEL R.; KOLOLUOMA,TERHO; LEVEY,RAVIV; RANTALA,JUHA T.; SHUL,RANDY J.; WARREN,MIAL E.; WILLISON,CHRISTI LEE

    1999-09-16

    We are developing a method of constructing compact, three-dimensional photonics systems consisting of optical elements, e.g., lenses and mirrors, photo-detectors, and light sources, e.g., VCSELS or circular-grating lasers. These optical components, both active and passive, are mounted on a lithographically prepared silicon substrate. We refer to the substrate as a micro-optical table (MOT) in analogy with the macroscopic version routinely used in optics laboratories. The MOT is a zero-alignment, microscopic optical-system concept. The position of each optical element relative to other optical elements on the MOT is determined in the layout of the MOT photomask. Each optical element fits into a slot etched in the silicon MOT. The slots are etched using a high-aspect-ratio silicon etching (HARSE) process. Additional positioning features in each slot's cross-section and complementary features on each optical element permit accurate placement of that element's aperture relative to the MOT substrate. In this paper we present the results of the first fabrication and micro-assembly experiments of a silicon-wafer based MOT. Based on these experiments, estimates of position accuracy are reported. We also report on progress in fabrication of lens elements in a hybrid sol-gel material (HSGM). Diffractive optical elements have been patterned in a 13-micron thick HSGM layer on a 150-micron thick soda-lime glass substrate. The measured ms surface roughness was 20 nm. Finally, we describe modeling of MOT systems using non-sequential ray tracing (NSRT).

  3. Maintenance Training and Performance: A Computer-Based Management Information System. Research Report 1360.

    ERIC Educational Resources Information Center

    Bobko, Douglas J.; Hayes, John F.

    A computer-based training program called the Maintenance Performance System (MPS) was developed and made operational in an Army divisional maintenance battalion. The primary purposes of the MPS were to monitor the daily technical activities of maintenance personnel by identifying maintenance strengths and deficiencies on both an individual and…

  4. FMIT alignment cart

    SciTech Connect

    Potter, R.C.; Dauelsberg, L.B.; Clark, D.C.; Grieggs, R.J.

    1981-01-01

    The Fusion Materials Irradiation Test (FMIT) Facility alignment cart must perform several functions. It must serve as a fixture to receive the drift-tube girder assembly when it is removed from the linac tank. It must transport the girder assembly from the linac vault to the area where alignment or disassembly is to take place. It must serve as a disassembly fixture to hold the girder while individual drift tubes are removed for repair. It must align the drift tube bores in a straight line parallel to the girder, using an optical system. These functions must be performed without violating any clearances found within the building. The bore tubes of the drift tubes will be irradiated, and shielding will be included in the system for easier maintenance.

  5. Standard hydrogen monitoring system-B operation and maintenance manual

    SciTech Connect

    Bender, R.M.

    1995-01-25

    The purpose of this document is to provide information for the operation and maintenance of the Standards Hydrogen Monitoring System-B (SHMS-B) used in the 200E and 200W area tank farms on the Hanford site. This provides information specific to the mechanical operation of the system and is not intended to take the place of a Plant Operating Procedure. The primary function of the SHMS-B is to monitor specifically for hydrogen in the waste tank vapor space which may also contain unknown quantities of other gaseous constituents.

  6. Metrology systems for active alignment control of the Hobby-Eberly Telescope wide field corrector

    NASA Astrophysics Data System (ADS)

    Lee, Hanshin; Hill, Gary J.; Hart, Michael; Cornell, Mark E.; Savage, Richard; Vattiat, Brian; Perry, Dave; Moller, William M.; Rafferty, Tom; Taylor, Trey; Rafal, Marc D.

    2010-07-01

    The Hobby-Eberly Telescope (HET) Wide-Field Upgrade (WFU) will be equipped with new metrology systems to actively control the optical alignment of the new four-mirror Wide-Field Corrector (WFC) as it tracks sidereal motion with respect to the fixed primary mirror. These systems include a tip/tilt sensor (TTS), distance measuring interferometers (DMI), guide probes (GP), and wavefront sensors (WFS). While the TTS and DMIs are to monitor the mechanical alignment of the WFC, the WFSs and GPs will produce direct measurement of the optical alignment of the WFC with respect to the HET primary mirror. Together, these systems provide fully redundant alignment and pointing information for the telescope, thereby keeping the WFC in focus and suppressing alignment-driven field aberrations. We describe the current snapshot of these systems and discuss their roles, expected performance, and operation plans.

  7. 49 CFR 229.29 - Air brake system calibration, maintenance, and testing.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ... 49 Transportation 4 2012-10-01 2012-10-01 false Air brake system calibration, maintenance, and... Inspections and Tests § 229.29 Air brake system calibration, maintenance, and testing. (a) A locomotive's air brake system shall receive the calibration, maintenance, and testing as prescribed in this section....

  8. 49 CFR 229.29 - Air brake system calibration, maintenance, and testing.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 49 Transportation 4 2013-10-01 2013-10-01 false Air brake system calibration, maintenance, and... Inspections and Tests § 229.29 Air brake system calibration, maintenance, and testing. (a) A locomotive's air brake system shall receive the calibration, maintenance, and testing as prescribed in this section....

  9. 49 CFR 229.29 - Air brake system calibration, maintenance, and testing.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 49 Transportation 4 2014-10-01 2014-10-01 false Air brake system calibration, maintenance, and... Inspections and Tests § 229.29 Air brake system calibration, maintenance, and testing. (a) A locomotive's air brake system shall receive the calibration, maintenance, and testing as prescribed in this section....

  10. The Alignment Test System for AXAF-I's High Resolution Mirror Assembly

    NASA Technical Reports Server (NTRS)

    Waldman, Mark

    1995-01-01

    The AXAF-1 High Resolution Mirror Assembly (HRMA) consists of four nested mirror pairs of Wolter Type-1 grazing incidence optics. The HRMA assembly and alignment will take place in a vibration-isolated, cleanliness class 100, 18 meter high tower at an Eastman Kodak Company facility in Rochester, NY. Each mirror pair must be aligned such that its image is coma-free, and the four pairs must be aligned such that their images are coincident. In addition, both the HRMA optical axis and focal point must be precisely known with respect to physical references on the HRMA. The alignment of the HRMA mirrors is measured by the HRMA Alignment Test System (HATS), which is an integral part of the tower facility. The HATS is configured as a double-pass, autocollimating Hartmann test where each mirror aperture is scanned to determine the state of alignment. This paper will describe the design and operation of the HATS.

  11. Operation and maintenance manual for the common video end effector system (CVEE) system 6260

    SciTech Connect

    Pardini, A.F., Westinghouse Hanford

    1996-07-24

    This document defines the requirements for the operation,maintenance, and storage of the Common Video End Effector System (CVEE) used with the video end effectors as part of the Light Duty Utility Arm (LDUA) system.

  12. Development the conceptual design of Knowledge Based System for Integrated Maintenance Strategy and Operation

    NASA Astrophysics Data System (ADS)

    Milana; Khan, M. K.; Munive, J. E.

    2014-07-01

    The importance of maintenance has escalated significantly by the increasing of automation in manufacturing process. This condition switches traditional maintenance perspective of inevitable cost into the business competitive driver. Consequently, maintenance strategy and operation decision needs to be synchronized to business and manufacturing concerns. This paper shows the development of conceptual design of Knowledge Based System for Integrated Maintenance Strategy and Operation (KBIMSO). The framework of KBIMSO is elaborated to show the process of how the KBIMSO works to reach the maintenance decision. By considering the multi-criteria of maintenance decision making, the KB system embedded with GAP and AHP to support integrated maintenance strategy and operation which is novel in this area. The KBIMSO is useful to review the existing maintenance system and give reasonable recommendation of maintenance decisions in respect to business and manufacturing perspective.

  13. Active alignment and vibration control system for a large airborne optical system

    NASA Astrophysics Data System (ADS)

    Kienholz, David A.

    2000-04-01

    Airborne optical or electro-optical systems may be too large for all elements to be mounted on a single integrating structure, other than the aircraft fuselage itself. An active system must then be used to maintain the required alignment between elements. However the various smaller integrating structures (benches) must still be isolated from high- frequency airframe disturbances that could excite resonances outside the bandwidth of the alignment control system. The combined active alignment and vibration isolation functions must be performed by flight-weight components, which may have to operate in vacuum. A testbed system developed for the Air Force Airborne Laser program is described. The payload, a full-scale 1650-lb simulated bench, is mounted in six degrees- of-freedom to a vibrating platform by a set of isolator- actuators. The mounts utilize a combination of pneumatics and magnetics to perform the dual functions of low-frequency alignment and high-frequency isolation. Test results are given and future directions for development are described.

  14. Advanced Ground Systems Maintenance Physics Models For Diagnostics Project

    NASA Technical Reports Server (NTRS)

    Perotti, Jose M.

    2015-01-01

    The project will use high-fidelity physics models and simulations to simulate real-time operations of cryogenic and systems and calculate the status/health of the systems. The project enables the delivery of system health advisories to ground system operators. The capability will also be used to conduct planning and analysis of cryogenic system operations. This project will develop and implement high-fidelity physics-based modeling techniques tosimulate the real-time operation of cryogenics and other fluids systems and, when compared to thereal-time operation of the actual systems, provide assessment of their state. Physics-modelcalculated measurements (called “pseudo-sensors”) will be compared to the system real-timedata. Comparison results will be utilized to provide systems operators with enhanced monitoring ofsystems' health and status, identify off-nominal trends and diagnose system/component failures.This capability can also be used to conduct planning and analysis of cryogenics and other fluidsystems designs. This capability will be interfaced with the ground operations command andcontrol system as a part of the Advanced Ground Systems Maintenance (AGSM) project to helpassure system availability and mission success. The initial capability will be developed for theLiquid Oxygen (LO2) ground loading systems.

  15. Practical Maintenance of Digital Systems: Guidance to Maximize the Benefits of Digital Technology for the Maintenance of Digital Systems and Plant Equipment

    SciTech Connect

    Hill, D; Scarola, K

    2004-10-30

    This report presents detailed guidance for the maintenance and testing of modern digital systems. The guidance provides practical means for plants to take advantage of the increased diagnostic and self-test capabilities of these systems. It helps plants avoid mistakes in design and installation that could lead to increased maintenance burden and decreased system reliability and availability.

  16. Aligning Evaluation Results and Professional Development: Driving Systemic Human Capital Management Reform

    ERIC Educational Resources Information Center

    Behrstock-Sherratt, Ellen; Jacques, Catherine

    2012-01-01

    This brief provides district and other educational leaders with research-based information on aligning professional development policies with teacher evaluations to drive more comprehensive human capital management. First, this brief describes an aligned evaluation and professional development system. Next, it discusses existing models and…

  17. An automatic and accurate x-ray tube focal spot/grid alignment system for mobile radiography: System description and alignment accuracy

    SciTech Connect

    Gauntt, David M.; Barnes, Gary T.

    2010-12-15

    Purpose: A mobile radiography automatic grid alignment system (AGAS) has been developed by modifying a commercially available mobile unit. The objectives of this article are to describe the modifications and operation and to report on the accuracy with which the focal spot is aligned to the grid and the time required to achieve the alignment. Methods: The modifications include an optical target arm attached to the grid tunnel, a video camera attached to the collimator, a motion control system with six degrees of freedom to position the collimator and x-ray tube, and a computer to control the system. The video camera and computer determine the grid position, and then the motion control system drives the x-ray focal spot to the center of the grid focal axis. The accuracy of the alignment of the focal spot with the grid and the time required to achieve alignment were measured both in laboratory tests and in clinical use. Results: For a typical exam, the modified unit automatically aligns the focal spot with the grid in less than 10 s, with an accuracy of better than 4 mm. The results of the speed and accuracy tests in clinical use were similar to the results in laboratory tests. Comparison patient chest images are presented--one obtained with a standard mobile radiographic unit without a grid and the other obtained with the modified unit and a 15:1 grid. The 15:1 grid images demonstrate a marked improvement in image quality compared to the nongrid images with no increase in patient dose. Conclusions: The mobile radiography AGAS produces images of significantly improved quality compared to nongrid images with alignment times of less than 10 s and no increase in patient dose.

  18. Standard Hydrogen Monitoring System-D operation and maintenance manual

    SciTech Connect

    Schneider, T.C.

    1997-05-01

    The purpose of this document is to provide information for the operation and maintenance of the Standard Hydrogen Monitoring System-D (SHMS-D) used in the 200E and 200W area tank farms on the Hanford Site. This provides information specific to the mechanical operation of the system and is not intended to take the place of a Plant Operating Procedure. However, it does provide more information on the system than a Plant Operating Procedure. The intent here is that the system is started up by a technician or engineer who has completed tank farms training course No. 351405, and then the only actions performed by Operations will be routine log taking. If any problems not addressed by the operating procedure are encountered with the unit, engineering should be contacted.

  19. Standard hydrogen monitoring system - E operation and maintenance manual

    SciTech Connect

    Schneider, T.C.

    1997-06-01

    The purpose of this document is to provide information for the operation and maintenance of the Standard Hydrogen Monitoring System- E (SHMS-E) used in the 200E and 20OW area tank farms on the Hanford Site. This provides information specific to the mechanical operation of the system and is not intended to take the place of a Plant Operating Procedure. However, it does provide more information on the system than a Plant Operating Procedure. The intent here is that the system is started up by a technician or engineer who has completed tank farms training course for SHMS, and then the only actions performed by Operations will be routine log taking. If any problems not addressed by the operating procedure are encountered with the unit, engineering should be contacted.

  20. A vision-aided alignment datum system for coordinate measuring machines

    NASA Astrophysics Data System (ADS)

    Wang, L.; Lin, G. C. I.

    1997-07-01

    This paper presents the development of a CAD-based and vision-aided precision measurement system. A new coordinate system alignment technique for coordinate measuring machines (CMMs) is described. This alignment technique involves a machine vision system with CAD-based planning and execution of inspection. The determination method for measuring datums for the coordinate measuring technique, using the AutoCAD development system, is described in more detail. To improve image quality in the machine vision system, a contrast enhancement technique is used on the image background to reduce image noise, and an on-line calibration technique is applied. Some systematic errors may be caused by imperfect geometric features in components during coordinate system alignment. This measurement system approach, with its new measuring coordinate alignment method, can be used for high-precision measurement to overcome such errors.

  1. Automated alignment of a reconfigurable optical system using focal-plane sensing and Kalman filtering.

    PubMed

    Fang, Joyce; Savransky, Dmitry

    2016-08-01

    Automation of alignment tasks can provide improved efficiency and greatly increase the flexibility of an optical system. Current optical systems with automated alignment capabilities are typically designed to include a dedicated wavefront sensor. Here, we demonstrate a self-aligning method for a reconfigurable system using only focal plane images. We define a two lens optical system with 8 degrees of freedom. Images are simulated given misalignment parameters using ZEMAX software. We perform a principal component analysis on the simulated data set to obtain Karhunen-Loève modes, which form the basis set whose weights are the system measurements. A model function, which maps the state to the measurement, is learned using nonlinear least-squares fitting and serves as the measurement function for the nonlinear estimator (extended and unscented Kalman filters) used to calculate control inputs to align the system. We present and discuss simulated and experimental results of the full system in operation. PMID:27505378

  2. Automated alignment of a reconfigurable optical system using focal-plane sensing and Kalman filtering

    NASA Astrophysics Data System (ADS)

    Fang, Joyce; Savransky, Dmitry

    2016-08-01

    Automation of alignment tasks can provide improved efficiency and greatly increase the flexibility of an optical system. Current optical systems with automated alignment capabilities are typically designed to include a dedicated wavefront sensor. Here, we demonstrate a self-aligning method for a reconfigurable system using only focal plane images. We define a two lens optical system with eight degrees of freedom. Images are simulated given misalignment parameters using ZEMAX software. We perform a principal component analysis (PCA) on the simulated dataset to obtain Karhunen-Lo\\`eve (KL) modes, which form the basis set whose weights are the system measurements. A model function which maps the state to the measurement is learned using nonlinear least squares fitting and serves as the measurement function for the nonlinear estimator (Extended and Unscented Kalman filters) used to calculate control inputs to align the system. We present and discuss both simulated and experimental results of the full system in operation.

  3. A particle swarm model for estimating reliability and scheduling system maintenance

    NASA Astrophysics Data System (ADS)

    Puzis, Rami; Shirtz, Dov; Elovici, Yuval

    2016-05-01

    Modifying data and information system components may introduce new errors and deteriorate the reliability of the system. Reliability can be efficiently regained with reliability centred maintenance, which requires reliability estimation for maintenance scheduling. A variant of the particle swarm model is used to estimate reliability of systems implemented according to the model view controller paradigm. Simulations based on data collected from an online system of a large financial institute are used to compare three component-level maintenance policies. Results show that appropriately scheduled component-level maintenance greatly reduces the cost of upholding an acceptable level of reliability by reducing the need in system-wide maintenance.

  4. Installation, operation, and maintenance for the pyramidal optics solar system installed at Yacht Cove, Columbia, SC

    SciTech Connect

    Not Available

    1980-09-01

    Information is presented concerning the installation, operation, and maintenance of the pyramidal Solar System for space heating and domestic hot water. Included are such items as principles of operation, sequence of installation, and procedures for the operation and maintenance of each subsystem making up the solar system. Also included are trouble-shooting charts and maintenance schedules.

  5. Use of Time Domain Reflectometers (TDRs) in Permeable Pavement Systems to Predict Maintenance Needs and Effectiveness

    EPA Science Inventory

    As the surface in permeable pavement systems clogs, infiltration capacity decreases, so maintenance is required to maintain hydrologic performance. There is limited direct guidance for determining when maintenance is needed to prevent surface runoff bypass. Research is being co...

  6. Note: O-ring stack system for electron gun alignment.

    PubMed

    Park, In-Yong; Cho, Boklae; Han, Cheolsu; Shin, Seungmin; Lee, Dongjun; Ahn, Sang Jung

    2015-01-01

    We present a reliable method for aligning an electron gun which consists of an electron source and lenses by controlling a stack of rubber O-rings in a vacuum condition. The beam direction angle is precisely tilted along two axes by adjusting the height difference of a stack of O-rings. In addition, the source position is shifted in each of three orthogonal directions. We show that the tilting angle and linear shift along the x and y axes as obtained from ten stacked O-rings are ±2.55° and ±2 mm, respectively. This study can easily be adapted to charged particle gun alignment and adjustments of the flange position in a vacuum, ensuring that its results can be useful with regard to electrical insulation between flanges with slight modifications. PMID:25638137

  7. Note: O-ring stack system for electron gun alignment

    NASA Astrophysics Data System (ADS)

    Park, In-Yong; Cho, Boklae; Han, Cheolsu; Shin, Seungmin; Lee, Dongjun; Ahn, Sang Jung

    2015-01-01

    We present a reliable method for aligning an electron gun which consists of an electron source and lenses by controlling a stack of rubber O-rings in a vacuum condition. The beam direction angle is precisely tilted along two axes by adjusting the height difference of a stack of O-rings. In addition, the source position is shifted in each of three orthogonal directions. We show that the tilting angle and linear shift along the x and y axes as obtained from ten stacked O-rings are ±2.55° and ±2 mm, respectively. This study can easily be adapted to charged particle gun alignment and adjustments of the flange position in a vacuum, ensuring that its results can be useful with regard to electrical insulation between flanges with slight modifications.

  8. Note: O-ring stack system for electron gun alignment

    SciTech Connect

    Park, In-Yong; Cho, Boklae; Han, Cheolsu; Shin, Seungmin; Lee, Dongjun; Ahn, Sang Jung

    2015-01-15

    We present a reliable method for aligning an electron gun which consists of an electron source and lenses by controlling a stack of rubber O-rings in a vacuum condition. The beam direction angle is precisely tilted along two axes by adjusting the height difference of a stack of O-rings. In addition, the source position is shifted in each of three orthogonal directions. We show that the tilting angle and linear shift along the x and y axes as obtained from ten stacked O-rings are ±2.55° and ±2 mm, respectively. This study can easily be adapted to charged particle gun alignment and adjustments of the flange position in a vacuum, ensuring that its results can be useful with regard to electrical insulation between flanges with slight modifications.

  9. Reconfigurable systems for sequence alignment and for general dynamic programming.

    PubMed

    Jacobi, Ricardo P; Ayala-Rincón, Mauricio; Carvalho, Luis G A; Llanos, Carlos H; Hartenstein, Reiner W

    2005-01-01

    Reconfigurable systolic arrays can be adapted to efficiently resolve a wide spectrum of computational problems; parallelism is naturally explored in systolic arrays and reconfigurability allows for redefinition of the interconnections and operations even during run time (dynamically). We present a reconfigurable systolic architecture that can be applied for the efficient treatment of several dynamic programming methods for resolving well-known problems, such as global and local sequence alignment, approximate string matching and longest common subsequence. The dynamicity of the reconfigurability was found to be useful for practical applications in the construction of sequence alignments. A VHDL (VHSIC hardware description language) version of this new architecture was implemented on an APEX FPGA (Field programmable gate array). It would be several magnitudes faster than the software algorithm alternatives. PMID:16342039

  10. Feasibility study for a transportation operations system cask maintenance facility

    SciTech Connect

    Rennich, M.J.; Medley, L.G.; Attaway, C.R.

    1991-01-01

    The US Department of Energy (DOE), Office of Civilian Radioactive Waste Management (OCRWM) is responsible for the development of a waste management program for the disposition of spent nuclear fuel (SNF) and high-level waste (HLW). The program will include a transportation system for moving the nuclear waste from the sources to a geologic repository for permanent disposal. Specially designed casks will be used to safely transport the waste. The cask systems must be operated within limits imposed by DOE, the Nuclear Regulatory Commission (NRC), and the Department of Transportation (DOT). A dedicated facility for inspecting, testing, and maintaining the cask systems was recommended by the General Accounting Office (in 1979) as the best means of assuring their operational effectiveness and safety, as well as regulatory compliance. In November of 1987, OCRWM requested a feasibility study be made of a Cask Maintenance Facility (CMF) that would perform the required functions. 46 refs., 16 figs., 13 tabs.

  11. A Decision Support System for Concrete Bridge Maintenance

    NASA Astrophysics Data System (ADS)

    Rashidi, Maria; Lemass, Brett; Gibson, Peter

    2010-05-01

    The maintenance of bridges as a key element in transportation infrastructure has become a major concern for asset managers and society due to increasing traffic volumes, deterioration of existing bridges and well-publicised bridge failures. A pivotal responsibility for asset managers in charge of bridge remediation is to identify the risks and assess the consequences of remediation programs to ensure that the decisions are transparent and lead to the lowest predicted losses in recognized constraint areas. The ranking of bridge remediation treatments can be quantitatively assessed using a weighted constraint approach to structure the otherwise ill-structured phases of problem definition, conceptualization and embodiment [1]. This Decision Support System helps asset managers in making the best decision with regards to financial limitations and other dominant constraints imposed upon the problem at hand. The risk management framework in this paper deals with the development of a quantitative intelligent decision support system for bridge maintenance which has the ability to provide a source for consistent decisions through selecting appropriate remediation treatments based upon cost, service life, product durability/sustainability, client preferences, legal and environmental constraints. Model verification and validation through industry case studies is ongoing.

  12. Linac cryogenic distribution system maintenance and upgrades at Jlab

    SciTech Connect

    Dixon, Kelly D.; Wright, Mathew C.; Ganni, Venkatarao

    2014-01-01

    The Central Helium Liquefier (CHL) distribution system to the CEBAF and FEL linacs at Jefferson Lab (JLab) experienced a planned warm up during the late summer and fall of 2012 for the first time after its commissioning in 1991. Various maintenance and modifications were performed to support high beam availability to the experimental users, meet 10 CFR 851 requirements for pressure systems, address operational issues, and prepare the cryogenic interfaces for the high-gradient cryomodules needed for the 12 GeV upgrade. Cryogenic maintenance and installation work had to be coordinated with other activities in the linacs and compete for manpower from other department installation activities. With less than a quarter of the gas storage capacity available to handle the boil-off from the more than 40 cryomodules, 35,000 Nm{sup 3} of helium was re-liquefied and shipped to a vendor via a liquid tanker trailer. Nearly 200 u-tubes had to be removed and stored while seals were replaced on related equipment such as vacuum pump outs, bayonet isolation and process valves.

  13. Linac cryogenic distribution system maintenance and upgrades at JLab

    SciTech Connect

    Dixon, K.; Wright, M.; Ganni, V.

    2014-01-29

    The Central Helium Liquefier (CHL) distribution system to the CEBAF and FEL linacs at Jefferson Lab (JLab) experienced a planned warm up during the late summer and fall of 2012 for the first time after its commissioning in 1991. Various maintenance and modifications were performed to support high beam availability to the experimental users, meet 10 CFR 851 requirements for pressure systems, address operational issues, and prepare the cryogenic interfaces for the high-gradient cryomodules needed for the 12 GeV upgrade. Cryogenic maintenance and installation work had to be coordinated with other activities in the linacs and compete for manpower from other department installation activities. With less than a quarter of the gas storage capacity available to handle the boil-off from the more than 40 cryomodules, 35,000 Nm{sup 3} of helium was re-liquefied and shipped to a vendor via a liquid tanker trailer. Nearly 200 u-tubes had to be removed and stored while seals were replaced on related equipment such as vacuum pump outs, bayonet isolation and process valves.

  14. Evaluation of mental workload on digital maintenance systems in nuclear power plants

    SciTech Connect

    Hwang, S. L.; Huang, F. H.; Lin, J. C.; Liang, G. F.; Yenn, T. C.; Hsu, C. C.

    2006-07-01

    The purpose of this study is to evaluate operators' mental workload dealing with digital maintenance systems in Nuclear Power Plants. First of all, according to the factors affected the mental workload, a questionnaire was designed to evaluate the mental workload of maintenance operators at the second Nuclear Power (NPP) in Taiwan. Then, sixteen maintenance engineers of the Second NPP participated in the questionnaire survey. The results indicated that the mental workload was lower in digital systems than that in analog systems. Finally, a mental workload model based on Neural Network technique was developed to predict the workload of maintenance operators in digital maintenance systems. (authors)

  15. Optical alignment of pixelated 4f optical system using multiplexed filter.

    PubMed

    Manivannan, N; Neil, M A A; Balachandran, W

    2013-11-10

    Novel optical alignment techniques to perform precise alignment of a typical pixelated 4f optical system are presented in this paper. These techniques use optical multiplexed matched filters, which were designed using a simple, efficient iterative optimization algorithm, known as direct binary search. Three alignment challenges are identified: positioning, focusing, and magnification. The first two alignments were performed using the optical multiplexed matched filtering technique, and the last one was performed using a new optical arrangement. Experimental results of the new alignment techniques and a simple optical pattern recognition problem to demonstrate the benefits of the new alignment techniques are also presented. Two pixelated, electrically addressed spatial light modulators (128 × 128 pixels and one pixel width is 80 μm) were used to represent the input and filter planes. The results clearly show that the new alignment techniques allow the 4f system to be aligned to a precision of 80 μm in the x-y direction and 0.716 mm in the z direction. PMID:24216742

  16. Metrology system for inter-alignment of lasers, telescopes, and mechanical datum

    NASA Astrophysics Data System (ADS)

    Aharon, Oren; Vishnia, Itai

    2015-10-01

    In modern scientific and industrial laser applications, inter-alignment of multiple optical devices is frequently a basic requirement to meet a certain specification and performance. However, the designed optical system combining mechanical elements, lasers and optical sights in various wavelengths frequently deviates from specified goals due to real life imperfections and effects. These may include mechanical tolerances, optical distortion, heating, laser cavity misalignment, overall instabilities, and non-linear effects. In order to deliver accurately and produce intricate optical systems, a carefully designed method for inter-alignment is required completing and updating the already existing methods. Thus, we designed and upgraded the performance of electronic autocollimator and combined it with innovative mechanical manipulation of optical invariants such as a Lateral Transfer Hollow Periscope to greatly improve and expand inter-alignment procedures. Depending on the combination of optical sights, laser types, and mechanical requirements, an appropriate method will be analyzed. For example, several layouts will be analyzed such as high power CO2 laser cavity alignment and laser delivery system mechanical rollers alignment. By completing the presented gear in this article other instruments such as Align Meter, Lateral Hollow Periscope (LTHPTM), Lateral Hollow Retroreflector ( LTHRTM) are available for applications such as alignment of articulated beam delivery systems.

  17. A distributed system for fast alignment of next-generation sequencing data

    PubMed Central

    Srimani, Jaydeep K.; Wu, Po-Yen; Phan, John H.; Wang, May D.

    2016-01-01

    We developed a scalable distributed computing system using the Berkeley Open Interface for Network Computing (BOINC) to align next-generation sequencing (NGS) data quickly and accurately. NGS technology is emerging as a promising platform for gene expression analysis due to its high sensitivity compared to traditional genomic microarray technology. However, despite the benefits, NGS datasets can be prohibitively large, requiring significant computing resources to obtain sequence alignment results. Moreover, as the data and alignment algorithms become more prevalent, it will become necessary to examine the effect of the multitude of alignment parameters on various NGS systems. We validate the distributed software system by (1) computing simple timing results to show the speed-up gained by using multiple computers, (2) optimizing alignment parameters using simulated NGS data, and (3) computing NGS expression levels for a single biological sample using optimal parameters and comparing these expression levels to that of a microarray sample. Results indicate that the distributed alignment system achieves approximately a linear speed-up and correctly distributes sequence data to and gathers alignment results from multiple compute clients.

  18. In Situ alignment system for phase-shifting point-diffraction interferometry

    DOEpatents

    Goldberg, Kenneth Alan; Naulleau, Patrick P.

    2000-01-01

    A device and method to facilitate the gross alignment of patterned object- and image-plane masks in optical systems such as the phase-shifting point diffraction interferometer are provided. When an array of similar pinholes or discreet mask fields is used, confusion can occur over the alignment of the focused beams within the field. Adding to the mask pattern a circumscribed or inscribed set of symbols that are identifiable in situ facilitates the unambiguous gross alignment of the object- and/or image-plane masks. Alternatively, a system of markings can be encoded directly into the window shape to accomplish this same task.

  19. Computer-aided alignment of off-axis three-mirror imaging spectrometer system

    NASA Astrophysics Data System (ADS)

    Gong, Dun; Wang, Hong; Tian, Tie-yin

    2013-08-01

    The space camera is one of the most advanced optical equipments in obtaining earth surface information from space. With the development of the optical design, manufacture and alignment technology, the performance of the optical camera is moving forward quickly. In spaceto- ground remote sensing field, the resolution of ground remote sensing images have become higher and higher. Off-axis three-mirror system becomes an advanced optical system structure of space camera at present , because of its merits of large field, long focal length, no obstruction, high modulated transfer function, wide spectrum, good image quality, small cubage and light weight, etc. As it is difficult to align and test, the alignment of off-axis three mirror system is timeconsuming, so it is important and necessary of studying the computer-aided alignment of the complex optical system. Aiming at cutting the time of alignment, Computer-aided alignment technology is applied to this system. According to relation between fringe Zernike coefficient and Seidel aberration, wavefront aberration in the exit pupil of optical system is instead with fringe Zernike coefficient. A series of Zernike coefficient expressing the incorrect parameters of system are obtained by using multi-fields ZYGO interferometer auto-collimating interference test, which are transformed into geometric aberrations as the corrected object. Incorrect parameters of the system are determined by sensitivity matrix resulted from optical design software. These incorrect parameters are defined to be variables; the Zernike coefficient are defined to be the optimized target in merit function. The system is optimized by applying optical design software to receive the incorrect parameters result. Consequently, the adjusted result is brought into the optical design software to verify the right selection of incorrect parameters. The practical experiments are also given, result with RMS value lower than 0.04λ is acquired by using this

  20. Developing Secure Power Systems Professional Competence: Alignment and Gaps in Workforce Development Programs—Summary Report

    SciTech Connect

    O'Neil, Lori Ross; Assante, Michael; Tobey, D. H.; Conway, T. J.; Vanderhorst, Jr, T. J.; Januszewski, III, J.; Leo, R.; Perman, K.

    2013-07-01

    This document is a summarization of the report, Developing Secure Power Systems Professional Competence: Alignment and Gaps in Workforce Development Programs, the final report for phase 2 of the SPSP (DOE workforce study) project.

  1. In-flight angular alignment of inertial navigation systems by means of radio aids

    NASA Technical Reports Server (NTRS)

    Tanner, W.

    1972-01-01

    The principles involved in the angular alignment of the inertial reference by nondirectional data from radio aids are developed and compared with conventional methods of alignment such as gyro-compassing and pendulous vertical determination. The specific problem is considered of the space shuttle reentry and a proposed technique for the alignment of the inertial reference system some time before landing. A description is given of the digital simulation of a transponder interrogation system and of its interaction with the inertial navigation system. Data from reentry simulations are used to demonstrate the effectiveness of in-flight inertial system alignment. Concluding remarks refer to other potential applications such as space shuttle orbit insertion and air navigation of conventional aircraft.

  2. RTEMS Centre - Support and Maintenance Centre to RTEMS Operating System

    NASA Astrophysics Data System (ADS)

    Silva, H.; Constantino, A.; Freitas, D.; Coutinho, M.; Faustino, S.; Mota, M.; Colaço, P.; Sousa, J.; Dias, L.; Damjanovic, B.; Zulianello, M.; Rufino, J.

    2009-05-01

    RTEMS CENTRE - Support and Maintenance Centre to RTEMS Operating System is a joint ESA/Portuguese Task Force initiative to develop a support and maintenance centre to the Real-Time Executive for Multiprocessor Systems (RTEMS). This paper gives a high level visibility of the progress, the results obtained and the future work in the RTEMS CENTRE [6] and in the RTEMS Improvement [7] projects. RTEMS CENTRE started officially in November 2006, with the RTEMS 4.6.99.2 version. A full analysis of RTEMS operating system was produced. The architecture was analysed in terms of conceptual, organizational and operational concepts. The original objectives [1] of the centre were primarily to create and maintain technical expertise and competences in this RTOS, to develop a website to provide the European Space Community an entry point for obtaining support (http://rtemscentre.edisoft.pt), to design, develop, maintain and integrate some RTEMS support tools (Timeline Tool, Configuration and Management Tools), to maintain flight libraries and Board Support Packages, to develop a strong relationship with the World RTEMS Community and finally to produce some considerations in ARINC-653, DO-178B and ECSS E-40 standards. RTEMS Improvement is the continuation of the RTEMS CENTRE. Currently the RTEMS, version 4.8.0, is being facilitated for a future qualification. In this work, the validation material is being produced following the Galileo Software Standards Development Assurance Level B [5]. RTEMS is being completely tested, errors analysed, dead and deactivated code removed and tests produced to achieve 100% statement and decision coverage of source code [2]. The SW to exploit the LEON Memory Management Unit (MMU) hardware will be also added. A brief description of the expected implementations will be given.

  3. Digital control of the High-Altitude Balloon Experiment auto-alignment system

    NASA Astrophysics Data System (ADS)

    Schulthess, Marcus R.; Baugh, Steven

    1995-05-01

    The High Altitude Balloon Experiments (HABE) control architecture design focuses on establishing an inertial stabilized line-of-sight (LOS) for the tracking and laser pointing subsystems. High bandwidth LOS stabilization is implemented with an inertial reference measurement system. The Inertial Pseudo Star Reference Unit (IPSRU), and inertially stabilized two degree of freedom platform, generates an inertially stabilized alignment reference beam which probes the multiple aperture system. Fast steering mirrors (FSM) in optical alignment loops track the alignment reference beam performing jitter stabilization and boresight alignment. The auto alignment system operates in the primary aperture beam path, stabilizing the fine tracking sensor imagery and surrogate high energy laser pointing subsystem. Due to the superior performance of the IPSRU stabilization platform, aggregate LOS stabilization system base motion and optical jitter rejection is directly traceable to the auto alignment system control dynamics and sensor noise performance. Performance requirements specify two axis FSM control bandwidths of 500 Hz with a positioning resolution better that 300 nano-radians in output space. The digital control law is implemented in high performance digital processors with sample rates in excess of 15 kHz. This paper presents the bench top integration and testing of the digital auto alignment system beginning with a discussion as to the reason behind choosing a digital implementation, a opposed to a much simple analog implementation. A description of the error budget requirements of the HABE digital auto alignment loop follows. The components comprising the auto alignment loop, including mirror and processor hardware and software are described. Experimental objectives are presented with a description of the laboratory setup. Simulation models are constructed from component test data to aid in the development of the alignment system control architecture and discrete time

  4. Note: A simple sample transfer alignment for ultra-high vacuum systems

    NASA Astrophysics Data System (ADS)

    Tamtögl, A.; Carter, E. A.; Ward, D. J.; Avidor, N.; Kole, P. R.; Jardine, A. P.; Allison, W.

    2016-06-01

    The alignment of ultra-high-vacuum sample transfer systems can be problematic when there is no direct line of sight to assist the user. We present the design of a simple and cheap system which greatly simplifies the alignment of sample transfer devices. Our method is based on the adaptation of a commercial digital camera which provides live views from within the vacuum chamber. The images of the camera are further processed using an image recognition and processing code which determines any misalignments and reports them to the user. Installation has proven to be extremely useful in order to align the sample with respect to the transfer mechanism. Furthermore, the alignment software can be easily adapted for other systems.

  5. Far-field detection system for laser beam and crystal alignment

    NASA Astrophysics Data System (ADS)

    Zhang, Jiachen; Liu, Daizhong; Zhu, Baoqiang; Tang, Shunxing; Gao, Yanqi

    2016-03-01

    Laser beam far-field alignment as well as frequency-doubling and frequency-tripling crystal adjustment is very important for high-power laser facility. Separate systems for beam and crystal alignment are generally used while the proposed approach by off-axial grating sampling share common optics for these two functions, reducing both space and cost requirements. This detection system has been demonstrated on the National Laser Facility of Israel. The experimental results indicate that the average far-field alignment error is <5% of the spatial filter pinhole diameter, average autocollimation angle error of crystals is <10 μrad, and average frequency-tripling conversion efficiency is 69.3%, which meet the alignment system requirements on the beam direction and crystals.

  6. Self-aligning amelogenin nanoribbons in oil-water system

    PubMed Central

    He, Xiaodong; Wu, Shenping; Martinez-Avila, Olga; Cheng, Yifan; Habelitz, Stefan

    2010-01-01

    The highly organized microstructure of dental enamel is a result of protein-guided anisotropic growth of apatite nanofibers. It is established that amelogenin proteins, the main constituent of the developing enamel matrix, form nanospheres in vitro, but the amphiphilic nature of the full-length protein conveys the possibility of generating more complex structures as observed with other surfactant-like molecules. This study tested if the use of metastable oil-water emulsions can induce supramolecular assemblies of amelogenin. Recombinant full-length amelogenin, rH174, was mixed into octanol/ethyl acetate preparations of different ratios to form emulsions at pH 4.5 and 7.4. Atomic force and electron microscopy showed the formation of 16.7±1.0 nm wide nanoribbons which grew to several micrometer length over a period of days. Nanoribbons formed from reverse micelles by enabling hydrophobic tails of the molecules to interact while preventing the formation of amelogenin nanospheres. Ribbon formation required the presence of calcium and phosphate ions and may be localized at a dark central line along the amelogenin ribbons. The ribbons have a strong tendency to align in parallel maintaining 5 to 20nm space between each other. The growth rates and number of ribbons were significantly higher at pH 4.5 and related to the metastability of the emulsion. A model for ribbon extension proposes the addition of short segments or amelogenin dimers to the ends of the ribbon. The formation of self-aligning and uniaxially elongating amelogenin structures triggered by the presence of calcium and phosphate may represent a suitable new model for protein controlled mineralization in enamel. PMID:21134461

  7. Active figure maintenance control using an optical truss laser metrology system for a space-based far-IR segmented telescope

    NASA Technical Reports Server (NTRS)

    Lau, Kenneth; Breckenridge, Bill; Nerheim, Noble; Redding, David

    1992-01-01

    A two-stage active control approach was developed addressing the figure control problem for a spaceborne FIR telescope, the Precision Segmented Reflectors Focus Moderate Mission Telescope (FMMT). The first active control stage aligns the optical segments based on images; attention is here given to the second stage, active figure maintenance control system, which maintains the alignment of the optical elements between initializations to hold the mirror figure steady while obtaining data and fixes translational and rotational changes of the optical segments induced by long-term thermal drifts of the support structure. Errors are expected to be 10-100 microns at the nodes of the primary backup structure over the course of an orbit. An rms performance of 0.8 microns of wavefront error can be expected during the maintenance function based on specified nominal sensor noises, actuator accuracies, and system environments. A performance of less than 0.3 microns rms can be expected, based on advanced components.

  8. Robotic system for remote maintenance of a pulsed nuclear reactor

    SciTech Connect

    Thunborg, S.

    1986-01-01

    Guidelines recently established for occupational radiation exposure specify that exposure should be as low as reasonably achievable. In conformance with these guidelines, SNL has developed a remote maintenance robot (RMR) system for use in the Sandia Pulse Reactor III (SPR III) facility. The RMR should reduce occupational radiation exposure by a factor of 4 and decrease reactor downtime. Other goals include developing a technology base for a more advanced pulse reactor and for the nuclear fuel cycle programs of the US Department of Energy and US Nuclear Regulatory Commission. The RMR has five major subsystems: (a) a chain-driven cart to bring the system into the reactor room; (b) a Puma 560 robot to perform dextrous operations; (c) a programmable turntable to orient the robot to any of the reactor's four sides; (d) a programmable overhead hoist for lifting components weighing up to 400 lb onto or off of the reactor; and (e) a supervisory control console for the system operator. Figure 1 is a schematic diagram of the turntable, hoist, and robot system in position around the SPR III reactor.

  9. Attitude Determination and Control System (ADCS) and Maintenance and Diagnostic System (MDS): A maintenance and diagnostic system for Space Station Freedom

    NASA Technical Reports Server (NTRS)

    Toms, David; Hadden, George D.; Harrington, Jim

    1990-01-01

    The Maintenance and Diagnostic System (MDS) that is being developed at Honeywell to enhance the Fault Detection Isolation and Recovery system (FDIR) for the Attitude Determination and Control System on Space Station Freedom is described. The MDS demonstrates ways that AI-based techniques can be used to improve the maintainability and safety of the Station by helping to resolve fault anomalies that cannot be fully determined by built-in-test, by providing predictive maintenance capabilities, and by providing expert maintenance assistance. The MDS will address the problems associated with reasoning about dynamic, continuous information versus only about static data, the concerns of porting software based on AI techniques to embedded targets, and the difficulties associated with real-time response. An initial prototype was built of the MDS. The prototype executes on Sun and IBM PS/2 hardware and is implemented in the Common Lisp; further work will evaluate its functionality and develop mechanisms to port the code to Ada.

  10. AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT IV, MAINTAINING THE COOLING SYSTEM--DETROIT DIESEL ENGINES.

    ERIC Educational Resources Information Center

    Human Engineering Inst., Cleveland, OH.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF THE DIESEL ENGINE COOLING SYSTEM. TOPICS ARE PURPOSE OF THE COOLING SYSTEM, CARE MAINTENANCE OF THE COOLING SYSTEM, COOLING SYSTEM COMPONENTS, AND TROUBLESHOOTING TIPS. THE MODULE CONSISTS OF A SELF-INSTRUCTIONAL BRANCH PROGRAMED TRAINING…

  11. Experimental findings on the underwater measurements uncertainty of speed of sound and the alignment system

    NASA Astrophysics Data System (ADS)

    Santos, T. Q.; Alvarenga, A. V.; Oliveira, D. P.; Mayworm, R. C.; Souza, R. M.; Costa-Félix, R. P. B.

    2016-07-01

    Speed of sound is an important quantity to characterize reference materials for ultrasonic applications, for instance. The alignment between the transducer and the test body is an key activity in order to perform reliable and consistent measurement. The aim of this work is to evaluate the influence of the alignment system to the expanded uncertainty of such measurement. A stainless steel cylinder was previously calibrated on an out of water system typically used for calibration of non-destructive blocks. Afterwards, the cylinder was calibrated underwater with two distinct alignment system: fixed and mobile. The values were statistically compared to the out-of-water measurement, considered the golden standard for such application. For both alignment systems, the normalized error was less than 0.8, leading to conclude that the both measurement system (under and out-of-water) do not diverge significantly. The gold standard uncertainty was 2.7 m-s-1, whilst the fixed underwater system resulted in 13 m-s-1, and the mobile alignment system achieved 6.6 m-s-1. After the validation of the underwater system for speed of sound measurement, it will be applied to certify Encapsulated Tissue Mimicking Material as a reference material for biotechnology application.

  12. Highly aligned lipid membrane systems in the physiologically relevant "excess water" condition.

    PubMed Central

    Katsaras, J

    1997-01-01

    The "excess water" condition in biologically relevant systems is met when a membrane mesophase coexists with excess bulk water. Further addition of water to such a system results in no change to any of the system's physical properties (e.g., transition temperature, repeat spacing, and structural mesophases). Moreover, because biological membranes are anisotropic systems, many of their properties are best studied using aligned samples. Although model membrane systems are routinely aligned, they have traditionally been hydrated with water vapor. It is well known that membranes exposed to water vapor at 100% humidity do not imbibe the same quantity of water as a sample in contact with liquid water. As such, membranes that have been hydrated with water vapor have physical properties different from those of membranes dispersed in water. Because of this shortcoming, aligned membranes have not been utilized to their full potential. Here we present a novel and simple method of aligning model membrane systems under conditions of excess water, which will make possible, for the first time, a variety of techniques (e.g., neutron and x-ray diffraction, nuclear magnetic resonance, electron spin resonance, attenuated total reflection infrared spectroscopy, etc.) for studying such systems under physiologically relevant conditions. In addition, when dealing with samples of limited availability, the system allows for the conditions (buffer pH and ionic strength) to be altered without any effect on the sample's alignment. Images FIGURE 1 PMID:9414206

  13. [The alignment of the optical system for 216 coude focus echelle spectrometer].

    PubMed

    Zhu, Y; Pan, J

    1997-04-01

    This paper gives a brief introduction about the structure of the echelle spectrometer which was installed at coude focus of the chinese 2. 16 meter astronomical telescope. According to the design requirment of this echelle spectrometer, the main points and steps of alignment of optical system are analysed. Authors work out a practical alignment scheme in which the fewest auxiliary tools are used. PMID:15810402

  14. Drive system alignment calibration of a microgravity drop tower of novel design

    NASA Astrophysics Data System (ADS)

    Trunins, J.; Osborne, B. P.; Augousti, A.

    2013-06-01

    We report here the calibration of the drive system of a new scientific facility for production of microgravity, operating on a novel design of electromagnetically driven platform. The construction achieves the design specification of alignment of the guide rails to better than 0.254mm across the entire guide rail height of 8m, despite a small lean to the right (within tolerance) and it was noted that this alignment is improved by the presence of the trolley that carries the platform.

  15. Alignment and maintenance free all-fiber laser source for CARS microscopy based on frequency conversion by four-wave-mixing

    NASA Astrophysics Data System (ADS)

    Baumgartl, Martin; Chemnitz, Mario; Jauregui, Cesar; Meyer, Tobias; Dietzek, Benjamin; Popp, Jürgen; Limpert, Jens; Tünnermann, Andreas

    2012-01-01

    In this contribution we report on a novel approach for pump and stokes pulse generation in extremely compact all-fiber systems using parametric frequency conversion (four-wave-mixing) in photonic-crystal fibers. Representing a completely alignment-free approach, the all-fiber ytterbium-based short-pulse laser system provides intrinsically synchronized tunable two-color picosecond pulses emitted from a single fiber end. The system was designed to address important CH-stretch vibrational resonances. Strong CARS signals are generated and proved by spectroscopic experiments, tuning the laser over the resonance of toluene at 3050cm-1. Furthermore the whole laser setup with a footprint of only 30x30cm2 is mounted on a home-built laser-scanning-microscope and CARS imaging capabilities are verified. The compact turn-key system represents a significant advance for CARS microscopy to enter real-world, in particular bio-medical, applications.

  16. System-size dependent band alignment in lateral two-dimensional heterostructures

    NASA Astrophysics Data System (ADS)

    Leenaerts, O.; Vercauteren, S.; Schoeters, B.; Partoens, B.

    2016-06-01

    The electronic band alignment in semiconductor heterostructures is a key factor for their use in electronic applications. The alignment problem has been intensively studied for bulk systems but is less well understood for low-dimensional heterostructures. In this work we investigate the alignment in two-dimensional lateral heterostructures. First-principles calculations are used to show that the electronic band offset depends crucially on the width and thickness of the heterostructure slab. The particular heterostructures under study consist of thin hydrogenated and fluorinated diamond slabs which are laterally joined together. Two different limits for the band offset are observed. For infinitely wide heterostructures the vacuum potential above the two materials is aligned leading to a large step potential within the heterostructure. For infinitely thick heterostructure slabs, on the other hand, there is no potential step in the heterostructure bulk, but a large potential step in the vacuum region above the heterojunction is observed. The band alignment in finite systems depends on the particular dimensions of the system. These observations are shown to result from an interface dipole at the heterojunction that tends to align the band structures.

  17. Object oriented software for simulation and reconstruction of big alignment systems

    NASA Astrophysics Data System (ADS)

    Arce, P.

    2003-04-01

    Modern high-energy physics experiments require tracking detectors to provide high precision under difficult working conditions (high magnetic field, gravity loads and temperature gradients). This is the reason why several of them are deciding to implement optical alignment systems to monitor the displacement of tracking elements in operation. To simulate and reconstruct optical alignment systems a general purpose software, named COCOA, has been developed, using the object oriented paradigm and software engineering techniques. Thanks to the big flexibility in its design, COCOA is able to reconstruct any optical system made of a combination of the following objects: laser, x-hair laser, incoherent source—pinhole, lens, mirror, plate splitter, cube splitter, optical square, rhomboid prism, 2D sensor, 1D sensor, distance-meter, tilt-meter, user-defined. COCOA was designed to satisfy the requirements of the CMS alignment system, which has several thousands of components. Sparse matrix techniques had been investigated for solving non-linear least squares fits with such a big number of parameters. The soundness of COCOA has already been stressed in the reconstruction of the data of a full simulation of a quarter plane of the CMS muon alignment system, which implied solving a system of 900 equations with 850 unknown parameters. Full simulation of the whole CMS alignment system, with over 30,000 parameters, is quite advanced. The integration of COCOA in the CMS software framework is also under progress.

  18. Virtual alignment of x-ray cone-beam tomography system using two calibration aperture measurements

    NASA Astrophysics Data System (ADS)

    Bronnikov, Andrei V.

    1999-02-01

    In cone-beam tomography, relatively small misalignment of the imaging system is geometrically magnified and may cause severe distortion of the reconstructed image. We describe a method for alignment of a cone-beam tomography system built on an x-ray microfocus tube, an image intensifier, and a high-resolution CCD camera. To obtain geometrical parameters of system misalignment, we suggest measuring two 180-deg- opposed cone-beam radiographs of a specially manufactured calibration aperture. An advantage of the aperture over other calibration objects is that we can easily restore its idealized picture by applying a certain threshold to the measured data. The method permits the lateral displacement vector and lateral tilt angle to be accurately found. Unlike other alignment methods, our approach enables virtual system alignment by using mathematical processing of the measured data, rather than moving the parts of the system. The virtually aligned system data are used for 3D image reconstruction by a standard filtered backprojection algorithm. Experimental results demonstrate considerable improvement of the image quality after applying the alignment method suggested.

  19. Facilitating Constructive Alignment in Power Systems Engineering Education Using Free and Open-Source Software

    ERIC Educational Resources Information Center

    Vanfretti, L.; Milano, F.

    2012-01-01

    This paper describes how the use of free and open-source software (FOSS) can facilitate the application of constructive alignment theory in power systems engineering education by enabling the deep learning approach in power system analysis courses. With this aim, this paper describes the authors' approach in using the Power System Analysis Toolbox…

  20. The Role of System Alignment in Care and Education of Children from Birth to Grade 3

    ERIC Educational Resources Information Center

    Ma, Xin; Shen, Jianping; Krenn, Huilan Y.; Yuan, Jing; Hu, Shanshan

    2015-01-01

    The emerging concept of system alignment refers to how different systems in care and education of young children can be integrated to work together as a whole system that is more effective, efficient, and equitable to produce excellent outcomes in children. The purpose of this article is to provide a review of the existing literature on system…

  1. Evaluation of Eight Methods for Aligning Orientation of Two Coordinate Systems.

    PubMed

    Mecheri, Hakim; Robert-Lachaine, Xavier; Larue, Christian; Plamondon, André

    2016-08-01

    The aim of this study was to evaluate eight methods for aligning the orientation of two different local coordinate systems. Alignment is very important when combining two different systems of motion analysis. Two of the methods were developed specifically for biomechanical studies, and because there have been at least three decades of algorithm development in robotics, it was decided to include six methods from this field. To compare these methods, an Xsens sensor and two Optotrak clusters were attached to a Plexiglas plate. The first optical marker cluster was fixed on the sensor and 20 trials were recorded. The error of alignment was calculated for each trial, and the mean, the standard deviation, and the maximum values of this error over all trials were reported. One-way repeated measures analysis of variance revealed that the alignment error differed significantly across the eight methods. Post-hoc tests showed that the alignment error from the methods based on angular velocities was significantly lower than for the other methods. The method using angular velocities performed the best, with an average error of 0.17 ± 0.08 deg. We therefore recommend this method, which is easy to perform and provides accurate alignment. PMID:27245737

  2. 25 CFR 170.806 - What is an IRR Transportation Facilities Maintenance Management System?

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... Management System? 170.806 Section 170.806 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR LAND... Transportation Facilities Maintenance Management System? An IRR Transportation Facilities Maintenance Management System (TFMMS) is a tool BIA and tribes will use to budget, prioritize, and schedule...

  3. AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT III, MAINTAINING THE FUEL SYSTEM--DETROIT DIESEL ENGINE.

    ERIC Educational Resources Information Center

    Human Engineering Inst., Cleveland, OH.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF THE DIESEL ENGINE FUEL SYSTEM. TOPICS ARE (1) PURPOSE OF THE FUEL SYSTEM, (2) TRACING THE FUEL FLOW, (3) MINOR COMPONENTS OF THE FUEL SYSTEM, (4) MAINTENANCE TIPS, (5) CONSTRUCTION AND FUNCTION OF THE FUEL INJECTORS, AND (6)…

  4. Small Water System Operations and Maintenance. A Field Study Training Program. Second Edition.

    ERIC Educational Resources Information Center

    Kerri, Kenneth D.; And Others

    Proper installation, inspection, operation, maintenance, repair and management of small water systems have a significant impact on the operation and maintenance cost and effectiveness of the systems. The objective of this manual is to provide small water system operators with the knowledge and skills required to operate and maintain these systems…

  5. Water Distribution System Operation and Maintenance. A Field Study Training Program. Second Edition.

    ERIC Educational Resources Information Center

    Kerri, Kenneth D.; And Others

    Proper installation, inspection, operation, maintenance, repair and management of water distribution systems have a significant impact on the operation and maintenance cost and effectiveness of the systems. The objective of this manual is to provide water distribution system operators with the knowledge and skills required to operate and maintain…

  6. Alignment validation

    SciTech Connect

    ALICE; ATLAS; CMS; LHCb; Golling, Tobias

    2008-09-06

    The four experiments, ALICE, ATLAS, CMS and LHCb are currently under constructionat CERN. They will study the products of proton-proton collisions at the Large Hadron Collider. All experiments are equipped with sophisticated tracking systems, unprecedented in size and complexity. Full exploitation of both the inner detector andthe muon system requires an accurate alignment of all detector elements. Alignmentinformation is deduced from dedicated hardware alignment systems and the reconstruction of charged particles. However, the system is degenerate which means the data is insufficient to constrain all alignment degrees of freedom, so the techniques are prone to converging on wrong geometries. This deficiency necessitates validation and monitoring of the alignment. An exhaustive discussion of means to validate is subject to this document, including examples and plans from all four LHC experiments, as well as other high energy experiments.

  7. The Poisson alignment reference system implementation at the Advanced Photon Source.

    SciTech Connect

    Feier, I.

    1998-09-21

    The Poisson spot was established using a collimated laser beam from a 3-mW diode laser. It was monitored on a quadrant detector and found to be very sensitive to vibration and air disturbances. Therefore, for future work we strongly recommend a sealed vacuum tube in which the Poisson line may be propagated. A digital single-axis feedback system was employed to generate an straight line reference (SLR) on the X axis. Pointing accuracy was better than 8 {+-} 2 microns at a distance of 5 m. The digital system was found to be quite slow with a maximum bandwidth of 47 {+-} 9 Hz. Slow drifts were easily corrected but any vibration over 5 Hz was not. We recommend an analog proportional-integral-derivative (PID) controller for high bandwidth and smooth operation of the kinematic mirror. Although the Poisson alignment system (PAS) at the Advanced Photon Source is still in its infancy, it already shows great promise as a possible alignment system for the low-energy undulator test line (LEUTL). Since components such as wigglers and quadruples will initially be aligned with respect to each other using conventional means and mounted on some kind of rigid rail, the goal would be to align six to ten such rails over a distance of about 30 m. The PAS could be used to align these rails by mounting a sphere at the joint between two rails. These spheres would need to be in a vacuum pipe to eliminate the refractive effects of air. Each sphere would not be attached to either rail but instead to a flange connecting the vacuum pipes of each rail. Thus the whole line would be made up of straight, rigid segments that could be aligned by moving the joints. Each sphere would have its own detector, allowing the operators to actively monitor the position of each joint and therefore the overall alignment of the system.

  8. Maintenance and storage of fuel oil for residential heating systems: A guide for residential heating system maintenance personnel

    SciTech Connect

    Litzke, Wai-Lin

    1992-12-01

    The quality of No. 2 fuel affects the performance of the heating system and is an important parameter in the proper and efficient operation of an oil-burning system. The physical and chemical characteristics of the fuel can affect the flow, atomization and combustion processes, all of which help to define and limit the overall performance of the heating system. The use of chemical additives by fuel oil marketershas become more common as a method of improving the quality of the fuel, especially for handling and storage. Numerous types of additives are available, but reliable information on their effectiveness and proper use is limited. This makes selecting an additive difficult in many situations. Common types of problems that contribute to poor fuel quality and how they affect residential heating equipment are identified inof this booklet. It covers the key items that are needed in an effective fuel quality monitoring program, such as what to look for when evaluating the quality of fuel as it is received from a supplier, or how to assess fuel problems associated with poor storage conditions. References to standard procedures and brief descriptions of the procedures also are given. Approaches for correcting a fuel-related problem, including the potential uses of chemical additives are discussed. Different types of additives are described to help users understand the functions and limitations of chemical treatment. Tips on how to select andeffectively use additives also are included. Finally, the importance of preventative maintenance in any fuel monitoring program is emphasized.

  9. Alignment of the stellar spin with the orbits of a three-planet system.

    PubMed

    Sanchis-Ojeda, Roberto; Fabrycky, Daniel C; Winn, Joshua N; Barclay, Thomas; Clarke, Bruce D; Ford, Eric B; Fortney, Jonathan J; Geary, John C; Holman, Matthew J; Howard, Andrew W; Jenkins, Jon M; Koch, David; Lissauer, Jack J; Marcy, Geoffrey W; Mullally, Fergal; Ragozzine, Darin; Seader, Shawn E; Still, Martin; Thompson, Susan E

    2012-07-26

    The Sun's equator and the planets' orbital planes are nearly aligned, which is presumably a consequence of their formation from a single spinning gaseous disk. For exoplanetary systems this well-aligned configuration is not guaranteed: dynamical interactions may tilt planetary orbits, or stars may be misaligned with the protoplanetary disk through chaotic accretion , magnetic interactions or torques from neighbouring stars. Indeed, isolated 'hot Jupiters' are often misaligned and even orbiting retrograde. Here we report an analysis of transits of planets over starspots on the Sun-like star Kepler-30 (ref. 8), and show that the orbits of its three planets are aligned with the stellar equator. Furthermore, the orbits are aligned with one another to within a few degrees. This configuration is similar to that of our Solar System, and contrasts with the isolated hot Jupiters. The orderly alignment seen in the Kepler-30 system suggests that high obliquities are confined to systems that experienced disruptive dynamical interactions. Should this be corroborated by observations of other coplanar multi-planet systems, then star-disk misalignments would be ruled out as the explanation for the high obliquities of hot Jupiters, and dynamical interactions would be implicated as the origin of hot Jupiters. PMID:22836999

  10. Software Engineering Laboratory (SEL) Data Base Maintenance System (DBAM) user's guide and system description

    NASA Technical Reports Server (NTRS)

    Lo, P. S.; Card, D.

    1983-01-01

    The Software Engineering Laboratory (SEL) Data Base Maintenance System (DBAM) is explained. The various software facilities of the SEL, DBAM operating procedures, and DBAM system information are described. The relationships among DBAM components (baseline diagrams), component descriptions, overlay descriptions, indirect command file listings, file definitions, and sample data collection forms are provided.

  11. Advanced Mask Aligner Lithography (AMALITH)

    NASA Astrophysics Data System (ADS)

    Voelkel, Reinhard; Vogler, Uwe; Bramati, Arianna

    2015-03-01

    Mask aligner lithography is very attractive for less-critical lithography layers and is widely used for LED, display, CMOS image sensor, micro-fluidics and MEMS manufacturing. Mask aligner lithography is also a preferred choice the semiconductor back-end for 3D-IC, TSV interconnects, advanced packaging (AdP) and wafer-level-packaging (WLP). Mask aligner lithography is a mature technique based on shadow printing and has not much changed since the 1980s. In shadow printing lithography a geometric pattern is transferred by free-space propagation from a photomask to a photosensitive layer on a wafer. The inherent simplicity of the pattern transfer offers ease of operation, low maintenance, moderate capital expenditure, high wafers-per-hour (WPH) throughput, and attractive cost-of-ownership (COO). Advanced mask aligner lithography (AMALITH) comprises different measures to improve shadow printing lithography beyond current limits. The key enabling technology for AMALITH is a novel light integrator systems, referred to as MO Exposure Optics® (MOEO). MOEO allows to fully control and shape the properties of the illumination light in a mask aligner. Full control is the base for accurate simulation and optimization of the shadow printing process (computational lithography). Now photolithography enhancement techniques like customized illumination, optical proximity correction (OPC), phase masks (AAPSM), half-tone lithography and Talbot lithography could be used in mask aligner lithography. We summarize the recent progress in advanced mask aligner lithography (AMALITH) and discuss possible measures to further improve shadow printing lithography.

  12. Precision alignment and calibration of optical systems using computer generated holograms

    NASA Astrophysics Data System (ADS)

    Coyle, Laura Elizabeth

    As techniques for manufacturing and metrology advance, optical systems are being designed with more complexity than ever before. Given these prescriptions, alignment and calibration can be a limiting factor in their final performance. Computer generated holograms (CGHs) have several unique properties that make them powerful tools for meeting these demanding tolerances. This work will present three novel methods for alignment and calibration of optical systems using computer generated holograms. Alignment methods using CGHs require that the optical wavefront created by the CGH be related to a mechanical datum to locate it space. An overview of existing methods is provided as background, then two new alignment methods are discussed in detail. In the first method, the CGH contact Ball Alignment Tool (CBAT) is used to align a ball or sphere mounted retroreflector (SMR) to a Fresnel zone plate pattern with micron level accuracy. The ball is bonded directly onto the CGH substrate and provides permanent, accurate registration between the optical wavefront and a mechanical reference to locate the CGH in space. A prototype CBAT was built and used to align and bond an SMR to a CGH. In the second method, CGH references are used to align axi-symmetric optics in four degrees of freedom with low uncertainty and real time feedback. The CGHs create simultaneous 3D optical references where the zero order reflection sets tilt and the first diffracted order sets centration. The flexibility of the CGH design can be used to accommodate a wide variety of optical systems and maximize sensitivity to misalignments. A 2-CGH prototype system was aligned multiplied times and the alignment uncertainty was quantified and compared to an error model. Finally, an enhanced calibration method is presented. It uses multiple perturbed measurements of a master sphere to improve the calibration of CGH-based Fizeau interferometers ultimately measuring aspheric test surfaces. The improvement in the

  13. An automated system for the alignment of large area modular solar simulators

    NASA Technical Reports Server (NTRS)

    Vincent, J. P.; Polak, L. F.; Fisher, P. S.

    1972-01-01

    A real-time optical alignment and diagnostic system is being assembled for installation at the Space Environment Simulation Laboratory. This system will be used to measure and analyze the performance of optical components, assemblies, and full modules. This information, in turn, is used to align assemblies and modules. The system capability includes such functions as the generation and updating of a catalog, which serves as permanent record, in addition to providing the capability to predict in-chamber performance of optics combinations before they are mounted in the chamber.

  14. Stability Measurements for Alignment of the NIF Neutron Imaging System Pinhole Array

    SciTech Connect

    Fittinghoff, D N; Bower, D E; Drury, O B; Dzenitis, J M; Frank, M; Buckles, R A; Munson, C; Wilde, C H

    2011-03-29

    The alignment system for the National Ignition Facility's neutron imaging system has been commissioned and measurements of the relative stability of the 90-315 DIM, the front and the back of the neutron imaging pinhole array and an exploding pusher target have been made using the 90-135 and the 90-258 opposite port alignment systems. Additionally, a laser beam shot from the neutron-imaging Annex and reflected from a mirror at the back of the pinhole array was used to monitor the pointing of the pinhole. Over a twelve hour period, the relative stability of these parts was found to be within {approx} {+-}18 {micro}m rms even when using manual methods for tracking the position of the objects. For highly visible features, use of basic particle tracking techniques found that the front of the pinhole array was stable relative to the 90-135 opposite port alignment camera to within {+-}3.4 {micro}m rms. Reregistration, however, of the opposite port alignment systems themselves using the target alignment sensor was found to change the expected position of target chamber center by up to 194 {micro}m.

  15. Design and performance of an automated video-based laser beam alignment system

    SciTech Connect

    Rundle, W.J. ); Kartz, M.W. ); Bliss, E.S.; English, R.E. Jr.; Peterson, R.L.; Thompson, G.R.; Uhlich, D.M. )

    1992-07-14

    This paper describes the design and performance of an automated, closed-loop, laser beam alignment system. Its function is to sense a beam alignment error in a laser beam transport system and automatically steer mirrors preceding the sensor location as required to maintain beam alignment. The laser beam is sampled by an optomechanical package which uses video cameras to sense pointing and centering errors. The camera outputs are fed to an image processing module, which includes video digitizers and uses image storage and software to sense the centroid of the image. Signals are sent through a VMEbus to an optical device controller'' (ODC), which drives stepper-motor actuators on mirror mounts preceding the beam-sampling location to return the beam alignment to the prescribed condition. Photodiodes are also used to extend the control bandwidth beyond that which is achievable with video cameras. This system has been operated at LLNL in the Atomic Vapor Laser Isotope Separation (AVLIS) program to maintain the alignment of copper and dye laser beams, the latter to within [plus minus]2 [mu]r in pointing and less than 1 mm in centering. The optomechanical design of the instrumented package, which includes lens, mirror, and video mounts in a rigid housing, the automated control system architecture, and the performance of this equipment is described.

  16. Design and performance of an automated video-based laser beam alignment system

    SciTech Connect

    Rundle, W.J.; Kartz, M.W.; Bliss, E.S.; English, R.E. Jr.; Peterson, R.L.; Thompson, G.R.; Uhlich, D.M.

    1992-07-14

    This paper describes the design and performance of an automated, closed-loop, laser beam alignment system. Its function is to sense a beam alignment error in a laser beam transport system and automatically steer mirrors preceding the sensor location as required to maintain beam alignment. The laser beam is sampled by an optomechanical package which uses video cameras to sense pointing and centering errors. The camera outputs are fed to an image processing module, which includes video digitizers and uses image storage and software to sense the centroid of the image. Signals are sent through a VMEbus to an ``optical device controller`` (ODC), which drives stepper-motor actuators on mirror mounts preceding the beam-sampling location to return the beam alignment to the prescribed condition. Photodiodes are also used to extend the control bandwidth beyond that which is achievable with video cameras. This system has been operated at LLNL in the Atomic Vapor Laser Isotope Separation (AVLIS) program to maintain the alignment of copper and dye laser beams, the latter to within {plus_minus}2 {mu}r in pointing and less than 1 mm in centering. The optomechanical design of the instrumented package, which includes lens, mirror, and video mounts in a rigid housing, the automated control system architecture, and the performance of this equipment is described.

  17. Automated alignment system for optical wireless communication systems using image recognition.

    PubMed

    Brandl, Paul; Weiss, Alexander; Zimmermann, Horst

    2014-07-01

    In this Letter, we describe the realization of a tracked line-of-sight optical wireless communication system for indoor data distribution. We built a laser-based transmitter with adaptive focus and ray steering by a microelectromechanical systems mirror. To execute the alignment procedure, we used a CMOS image sensor at the transmitter side and developed an algorithm for image recognition to localize the receiver's position. The receiver is based on a self-developed optoelectronic integrated chip with low requirements on the receiver optics to make the system economically attractive. With this system, we were able to set up the communication link automatically without any back channel and to perform error-free (bit error rate <10⁻⁹) data transmission over a distance of 3.5 m with a data rate of 3 Gbit/s. PMID:24978803

  18. Eccentricity Inferences in Multi-planet systems with Transit Timing: Degeneracies and Apsidal Alignment

    NASA Astrophysics Data System (ADS)

    Jontof-Hutter, Daniel; Van Laerhoven, Christa L.; Ford, Eric B.

    2016-05-01

    Hundreds of multi-transiting systems discovered by the Kepler mission show Transit Timing Variations (TTV). In cases where the TTVs are uniquely attributable to transiting planets, the TTVs enable precise measurements of planetary masses and orbital parameters. Of particular interest are the constraints on eccentricity vectors that can be inferred in systems of low-mass exoplanets.The TTVs in these systems are dominated by a signal caused by near-resonant mean motions. This causes the well-known near-degeneracy between planetary masses and orbital eccentricities. In addition, it causes a degeneracy between the eccentricities of interacting planet pairs.For many systems, the magnitude of individual eccentricities are weakly constrained, yet the data typically provide a tight constraint on the posterior joint distribution for the eccentricity vector components. This permits tight constraints on the relative eccentricity and degree of alignment of interacting planets.For a sample of two and three-planet systems with TTVs, we highlight the effects of these correlations. While the most eccentric orbital solutions for these systems show apsidal alignment, this is often due to the degeneracy that causes correlated constraints on the eccentricity vector components. We compare the likelihood of apsidal alignment for two choices of eccentricity prior: a wide prior using a Rayleigh distribution of scale length 0.1 and a narrower prior with scale length 0.02. In all cases the narrower prior decreased the fraction of samples that exhibited apsidal alignment. However, apsidal alignment persisted in the majority of cases with a narrower eccentricity prior. For a sample of our TTV solutions, we ran simulations of these systems over secular timescales, and decomposed their eccentricity eigenmodes over time, confirming that in most cases, the eccentricities were dominated by parallel eigenmodes which favor apsidal alignment.

  19. Microwave systems analysis, solar power satellite. [alignment of the antenna array

    NASA Technical Reports Server (NTRS)

    1979-01-01

    Various alternative active approaches to achieving aand maintaining flatness for the microwave power transmission system (MPTS) were studied. A baseline active alignment scheme was developed which includes subarray attachment mechanisms, height and tilting adjustments, service corridors, a rotating laser beam reference system, monopulse pointing techniques, and the design of a beam-centering photoconductive sensor.

  20. Maintenance of an angle between planes of orbits in multisatellite systems

    NASA Astrophysics Data System (ADS)

    Baranov, A. A.; Budyansky, A. A.; Chernov, N. V.

    2015-09-01

    The problem of the maintenance of an angle between planes of orbits in a multisatellite system is considered. It is assumed that one of the satellites is active, to be later used for the servicing of a spacecraft located in an orbit of another level. Simple maintenance of system configuration is also considered. Various schemes of the maintenance of the angle including schemes that provide the minimum angle between the planes of the orbits at the time of the optimal phase mismatch for approach maneuvers. Four examples of the solution of the problem are given that make it possible to estimate the effectiveness of various maintenance schemes.

  1. AUTOMOTIVE DIESEL MAINTENANCE, UNIT V, MAINTAINING THE LUBRICATION SYSTEM--DETROIT DIESEL ENGINE.

    ERIC Educational Resources Information Center

    Human Engineering Inst., Cleveland, OH.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF THE DIESEL ENGINE LUBRICATION SYSTEM. TOPICS ARE LUBE OILS USED, MAINTENANCE OF THE LUBRICATION SYSTEM, AND CRANKCASE VENTILATION COMPONENTS. THE MODULE CONSISTS OF A SELF-INSTRUCTIONAL BRANCH PROGRAMED TRAINING FILM "BASIC ENGINE…

  2. 14 CFR 1212.601 - Maintenance and publication requirements for systems of records.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 14 Aeronautics and Space 5 2011-01-01 2010-01-01 true Maintenance and publication requirements for systems of records. 1212.601 Section 1212.601 Aeronautics and Space NATIONAL AERONAUTICS AND SPACE ADMINISTRATION PRIVACY ACT-NASA REGULATIONS Instructions for NASA Employees § 1212.601 Maintenance and publication requirements for systems of...

  3. Maintenance Training and Performance: A Computer-Based Management Information System.

    ERIC Educational Resources Information Center

    Bobko, Douglas J.; Hayes, John F.

    1983-01-01

    The Army Research Institute developed and made operational a computer-based maintenance performance management information system that monitors technical activities of maintenance personnel. The implications of data from eight months of system operation for training programs, training material development, estimating manning requirements,…

  4. The Design and Implementation of Aircraft Maintenance On-site Control System

    NASA Astrophysics Data System (ADS)

    Zhou, Guilin; Zhang, Huawei

    Based on the desire of aircraft maintenance, combined with the situation in work, this paper present the design and implementation of aircraft maintenance system based dot Net. For a partial page refresh object, AJAX is used through the system. New technology is used in a creative way and will promote innovation and transformation of the business.

  5. 30 CFR 250.516 - Blowout preventer system tests, inspections, and maintenance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Well-Completion Operations § 250.516 Blowout preventer system tests, inspections, and maintenance. (a... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Blowout preventer system tests, inspections, and maintenance. 250.516 Section 250.516 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT...

  6. Aligning Food Systems Policies to Advance Public Health

    PubMed Central

    Muller, Mark; Tagtow, Angie; Roberts, Susan L.; MacDougall, Erin

    2009-01-01

    The involvement of public health professionals in food and agricultural policy provides tremendous opportunities for advancing the public's health. It is particularly challenging, however, for professionals to understand and consider the numerous policy drivers that impact the food system, which range from agricultural commodity policies to local food safety ordinances. Confronted with this complexity in the food system, policy advocates often focus on narrow objectives with disregard for the larger system. This commentary contends that, in order to be most effective, public health professionals need to consider the full range of interdependent policies that affect the system. Food policy councils have proven to be an effective tool, particularly at the local and state level, for developing comprehensive food systems policies that can improve public health. PMID:23144671

  7. The LES of the channel flow in a non aligned system of coordinates

    NASA Astrophysics Data System (ADS)

    Germano, Massimo; Abbà, Antonella

    2010-11-01

    The plane channel flow continues to be a very important test case for the verification and the validation of LES. In the channel flow test there is a privileged direction, usually one reference axis is oriented along the stream and the size of the computational box is increased in the streamwise direction in order to capture correctly the dominant turbulent structures and to produce a fully developed flow. All that is peculiar of this particular test, and in this paper we will investigate the sensitivity of the channel test to the particular alignment of the coordinate system with the mean flow. In a non aligned system of coordinates there is no privileged direction, there are two components of the forcing term, the mean pressure gradient, and the homogeneities of the Reynolds stresses are destroyed. In our paper we simulate the channel flow in a rotated system of coordinates, and we compare the results with the stream aligned data. We think that this test could evidence the flexibility of different LES codes and LES subgrid models to simulate the turbulent flow and to capture the correct statistical values in non aligned conditions. The first preliminary results are slightly contradictory: the resolved Reynolds stresses seem degraded while the mean flow is better predicted. The dynamic anisotropic subgrid model of Abbà, Cercignani and Valdettaro seems well fitted to represent correctly the large scales in non aligned conditions.

  8. Alignment of the measurement scale mark during immersion hydrometer calibration using an image processing system.

    PubMed

    Peña-Perez, Luis Manuel; Pedraza-Ortega, Jesus Carlos; Ramos-Arreguin, Juan Manuel; Arriaga, Saul Tovar; Fernandez, Marco Antonio Aceves; Becerra, Luis Omar; Hurtado, Efren Gorrostieta; Vargas-Soto, Jose Emilio

    2013-01-01

    The present work presents an improved method to align the measurement scale mark in an immersion hydrometer calibration system of CENAM, the National Metrology Institute (NMI) of Mexico, The proposed method uses a vision system to align the scale mark of the hydrometer to the surface of the liquid where it is immersed by implementing image processing algorithms. This approach reduces the variability in the apparent mass determination during the hydrostatic weighing in the calibration process, therefore decreasing the relative uncertainty of calibration. PMID:24284770

  9. Alignment of the Measurement Scale Mark during Immersion Hydrometer Calibration Using an Image Processing System

    PubMed Central

    Peña-Perez, Luis Manuel; Pedraza-Ortega, Jesus Carlos; Ramos-Arreguin, Juan Manuel; Arriaga, Saul Tovar; Fernandez, Marco Antonio Aceves; Becerra, Luis Omar; Hurtado, Efren Gorrostieta; Vargas-Soto, Jose Emilio

    2013-01-01

    The present work presents an improved method to align the measurement scale mark in an immersion hydrometer calibration system of CENAM, the National Metrology Institute (NMI) of Mexico, The proposed method uses a vision system to align the scale mark of the hydrometer to the surface of the liquid where it is immersed by implementing image processing algorithms. This approach reduces the variability in the apparent mass determination during the hydrostatic weighing in the calibration process, therefore decreasing the relative uncertainty of calibration. PMID:24284770

  10. Active mirror alignment control system for the MACE telescope

    NASA Astrophysics Data System (ADS)

    Kulgod, S. V.; Pious, Lizy; Chadda, V. K.; Kaul, S. R.; Yadav, K. K.; Koul, R.

    2002-03-01

    The conceptual design of an active mirror contol system for the MACE telescope, being set up by the Bhabha Atomic Research Centre at Mt. Abu, is described. Preliminary results obtained from recent laboratory trials are also described.

  11. WAVELENGTH AND ALIGNMENT TESTS FOR CONFOCAL SPECTRAL IMAGING SYSTEMS

    EPA Science Inventory

    Confocal spectral imaging (CSI) microscope systems now on the market delineate multiple fluorescent proteins, labels, or dyes within biological specimens by performing spectral characterizations. However, we find that some CSI present inconsistent spectral profiles of reference s...

  12. The maintenance of soil fertility in Amazonian managed systems

    NASA Astrophysics Data System (ADS)

    Luizão, Flávio J.; Fearnside, Philip M.; Cerri, Carlos E. P.; Lehmann, Johannes

    Most of Brazilian Amazonia faces important limitations for conventional agriculture and pastures due to a generally poor chemical fertility as well as the region's environmental conditions, especially high temperature and moisture. Without proper management, degradation of the soil and resulting unsustainability of agricultural and ranching production occur within a few years, leading to land abandonment. Use of perennial crops, especially those based on native tree species, would be instrumental in order to achieve best management such as that which assure recycling processes similar to those in the primary forest. Recommended alternative land uses are those producing high soil organic matter, recycling of nutrients, substantial agricultural production, and economic viability. These include agroforestry systems, enrichment of second growth with valuable native timber or fruit species, accelerated fallow regrowth via enrichment plantings, sequential agroforestry with slash-and-mulch, and diversified forest plantations. Improvement of agricultural soils can be based on lessons learned from the study of processes involved in the formation and maintenance of the rich "dark earths" (terra preta), which owe their high carbon content and fertility in part to high content of charcoal. Adding powdered charcoal combined with selected nutrients can increase soil carbon in modern agriculture. Considering that limitations to expansion of intensified land uses in Amazonia are serious, regional development should emphasize the natural forest, which can maintain itself without external inputs of nutrients. Instead of creating conditions to further expand deforestation, these forests may be used as they stand to provide a variety of valuable environmental services that could offer a sustainable basis for development of Amazonia.

  13. Fabrication and testing of a prototype longwall face alignment system

    NASA Technical Reports Server (NTRS)

    1981-01-01

    Fabrication and testing of a laser system for instantaneous location of a longwall shearer are summarized. Calculations and measurements for the design of a laser based system for monitoring and controlling the trajectory of the shearing machine as it progresses along the longwall face are reported. An early version was fabricated by employing simple mechanical contrivances and a standard miners lamp. It is concluded that the advantages of the early version is the ability to test the longwall face without approval from the Mine Safety and Health Administration.

  14. Magnetic prism alignment system for measuring large-angle strabismus.

    PubMed

    Bishop, John Edward

    2014-02-01

    Prismatic measurement of large-angle strabismus requires the simultaneous use of two or more prisms for neutralization. To facilitate the clinical measurement of large-angle strabismus a new prism system was designed utilizing a flat plate and a ferrous metal surface coupled with prisms containing rare earth magnets implanted in their base and bottom surfaces. PMID:24569000

  15. A line-source method for aligning on-board and other pinhole SPECT systems

    PubMed Central

    Yan, Susu; Bowsher, James; Yin, Fang-Fang

    2013-01-01

    Purpose: In order to achieve functional and molecular imaging as patients are in position for radiation therapy, a robotic multipinhole SPECT system is being developed. Alignment of the SPECT system—to the linear accelerator (LINAC) coordinate frame and to the coordinate frames of other on-board imaging systems such as cone-beam CT (CBCT)—is essential for target localization and image reconstruction. An alignment method that utilizes line sources and one pinhole projection is proposed and investigated to achieve this goal. Potentially, this method could also be applied to the calibration of the other pinhole SPECT systems. Methods: An alignment model consisting of multiple alignment parameters was developed which maps line sources in three-dimensional (3D) space to their two-dimensional (2D) projections on the SPECT detector. In a computer-simulation study, 3D coordinates of line-sources were defined in a reference room coordinate frame, such as the LINAC coordinate frame. Corresponding 2D line-source projections were generated by computer simulation that included SPECT blurring and noise effects. The Radon transform was utilized to detect angles (α) and offsets (ρ) of the line-source projections. Alignment parameters were then estimated by a nonlinear least squares method, based on the α and ρ values and the alignment model. Alignment performance was evaluated as a function of number of line sources, Radon transform accuracy, finite line-source width, intrinsic camera resolution, Poisson noise, and acquisition geometry. Experimental evaluations were performed using a physical line-source phantom and a pinhole-collimated gamma camera attached to a robot. Results: In computer-simulation studies, when there was no error in determining angles (α) and offsets (ρ) of the measured projections, six alignment parameters (three translational and three rotational) were estimated perfectly using three line sources. When angles (α) and offsets (ρ) were provided by

  16. A line-source method for aligning on-board and other pinhole SPECT systems

    SciTech Connect

    Yan, Susu; Bowsher, James; Yin, Fang-Fang

    2013-12-15

    Purpose: In order to achieve functional and molecular imaging as patients are in position for radiation therapy, a robotic multipinhole SPECT system is being developed. Alignment of the SPECT system—to the linear accelerator (LINAC) coordinate frame and to the coordinate frames of other on-board imaging systems such as cone-beam CT (CBCT)—is essential for target localization and image reconstruction. An alignment method that utilizes line sources and one pinhole projection is proposed and investigated to achieve this goal. Potentially, this method could also be applied to the calibration of the other pinhole SPECT systems.Methods: An alignment model consisting of multiple alignment parameters was developed which maps line sources in three-dimensional (3D) space to their two-dimensional (2D) projections on the SPECT detector. In a computer-simulation study, 3D coordinates of line-sources were defined in a reference room coordinate frame, such as the LINAC coordinate frame. Corresponding 2D line-source projections were generated by computer simulation that included SPECT blurring and noise effects. The Radon transform was utilized to detect angles (α) and offsets (ρ) of the line-source projections. Alignment parameters were then estimated by a nonlinear least squares method, based on the α and ρ values and the alignment model. Alignment performance was evaluated as a function of number of line sources, Radon transform accuracy, finite line-source width, intrinsic camera resolution, Poisson noise, and acquisition geometry. Experimental evaluations were performed using a physical line-source phantom and a pinhole-collimated gamma camera attached to a robot.Results: In computer-simulation studies, when there was no error in determining angles (α) and offsets (ρ) of the measured projections, six alignment parameters (three translational and three rotational) were estimated perfectly using three line sources. When angles (α) and offsets (ρ) were provided by

  17. Developing Mobile- and BIM-Based Integrated Visual Facility Maintenance Management System

    PubMed Central

    Su, Yu-Chih

    2013-01-01

    Facility maintenance management (FMM) has become an important topic for research on the operation phase of the construction life cycle. Managing FMM effectively is extremely difficult owing to various factors and environments. One of the difficulties is the performance of 2D graphics when depicting maintenance service. Building information modeling (BIM) uses precise geometry and relevant data to support the maintenance service of facilities depicted in 3D object-oriented CAD. This paper proposes a new and practical methodology with application to FMM using BIM technology. Using BIM technology, this study proposes a BIM-based facility maintenance management (BIMFMM) system for maintenance staff in the operation and maintenance phase. The BIMFMM system is then applied in selected case study of a commercial building project in Taiwan to verify the proposed methodology and demonstrate its effectiveness in FMM practice. Using the BIMFMM system, maintenance staff can access and review 3D BIM models for updating related maintenance records in a digital format. Moreover, this study presents a generic system architecture and its implementation. The combined results demonstrate that a BIMFMM-like system can be an effective visual FMM tool. PMID:24227995

  18. Developing mobile- and BIM-based integrated visual facility maintenance management system.

    PubMed

    Lin, Yu-Cheng; Su, Yu-Chih

    2013-01-01

    Facility maintenance management (FMM) has become an important topic for research on the operation phase of the construction life cycle. Managing FMM effectively is extremely difficult owing to various factors and environments. One of the difficulties is the performance of 2D graphics when depicting maintenance service. Building information modeling (BIM) uses precise geometry and relevant data to support the maintenance service of facilities depicted in 3D object-oriented CAD. This paper proposes a new and practical methodology with application to FMM using BIM technology. Using BIM technology, this study proposes a BIM-based facility maintenance management (BIMFMM) system for maintenance staff in the operation and maintenance phase. The BIMFMM system is then applied in selected case study of a commercial building project in Taiwan to verify the proposed methodology and demonstrate its effectiveness in FMM practice. Using the BIMFMM system, maintenance staff can access and review 3D BIM models for updating related maintenance records in a digital format. Moreover, this study presents a generic system architecture and its implementation. The combined results demonstrate that a BIMFMM-like system can be an effective visual FMM tool. PMID:24227995

  19. Power Grid Maintenance Scheduling Intelligence Arrangement Supporting System Based on Power Flow Forecasting

    NASA Astrophysics Data System (ADS)

    Xie, Chang; Wen, Jing; Liu, Wenying; Wang, Jiaming

    With the development of intelligent dispatching, the intelligence level of network control center full-service urgent need to raise. As an important daily work of network control center, the application of maintenance scheduling intelligent arrangement to achieve high-quality and safety operation of power grid is very important. By analyzing the shortages of the traditional maintenance scheduling software, this paper designs a power grid maintenance scheduling intelligence arrangement supporting system based on power flow forecasting, which uses the advanced technologies in maintenance scheduling, such as artificial intelligence, online security checking, intelligent visualization techniques. It implements the online security checking of maintenance scheduling based on power flow forecasting and power flow adjusting based on visualization, in order to make the maintenance scheduling arrangement moreintelligent and visual.

  20. Test evaluation of space station ECLSS maintenance concepts. [Environmental Control and Life Support System

    NASA Technical Reports Server (NTRS)

    Reysa, R. P.; Flugel, C. W.; Thompson, C. D.

    1978-01-01

    The Space Station Prototype (SSP) Environmental Control and Life Support System (ECLSS) hardware was designed and built to be maintainable by the flight crew. To achieve this goal, subsystems were designed for ease of component removal and installation, which included accessibility to component fasteners and connectors, adequate tool clearance, minimum fluid loss during changeout, positive capture of loose parts during changeout, replacement by one crewman, and protection of adjacent parts during maintenance. During testing of this hardware, many day-to-day problems arose which allowed the evaluation of the maintenance concepts under actual maintenance conditions. This paper briefly discusses the maintenance objectives of the hardware design. Specific maintenance designs and their test evaluations are discussed. A removable cartridge valve concept for liquid line components and threaded mechanical fittings and V-band couplings for gaseous line components are critiqued. Other maintenance devices are also evaluated.

  1. Engine health monitoring systems: Tools for improved maintenance management in the 1980's

    NASA Technical Reports Server (NTRS)

    Kimball, J. C.

    1981-01-01

    The performance monitoring aspect of maintenance, characteristic of the engine health monitoring system are discussed. An overview of the system activities is presented and a summary of programs for improved monitoring in the 1980's are discussed.

  2. Alignment of the ALICE Inner Tracking System with Cosmic-Ray Tracks

    SciTech Connect

    Aamodt, K.; Awes, Terry C; Enokizono, Akitomo; Silvermyr, David O; ALICE, Collaboration

    2010-03-01

    ALICE (A Large Ion Collider Experiment) is the LHC (Large Hadron Collider) experiment devoted to investigating the strongly interacting matter created in nucleus-nucleus collisions at the LHC energies. The ALICE ITS, Inner Tracking System, consists of six cylindrical layers of silicon detectors with three different technologies; in the outward direction: two layers of pixel detectors, two layers each of drift, and strip detectors. The number of parameters to be determined in the spatial alignment of the 2198 sensor modules of the ITS is about 13,000. The target alignment precision is well below 10 {micro}m in some cases (pixels). The sources of alignment information include survey measurements, and the reconstructed tracks from cosmic rays and from proton-proton collisions. The main track-based alignment method uses the Millepede global approach. An iterative local method was developed and used as well. We present the results obtained for the ITS alignment using about 10{sup 5} charged tracks from cosmic rays that have been collected during summer 2008, with the ALICE solenoidal magnet switched off.

  3. An Improved Alignment Method for the Strapdown Inertial Navigation System (SINS)

    PubMed Central

    Liu, Meng; Gao, Yanbin; Li, Guangchun; Guang, Xingxing; Li, Shutong

    2016-01-01

    In this paper, an innovative inertial navigation system (INS) mechanization and the associated Kalman filter (KF) are developed to implement a fine alignment for the strapdown INS (SINS) on stationary base. The improved mechanization is established in the pseudo-geographic frame, which is rebuilt based on the initial position. The new mechanization eliminates the effects of linear movement errors on the heading by decoupling. Compared with the traditional local-level mechanization, it has more advantages. The proposed algorithm requires lower coarse alignment accuracy in both the open-loop and closed-loop KFs and hence can improve the system reliability and decrease the total alignment time. Moreover, for the closed-loop KF, it can decrease oscillation caused by the system errors and improve the closed-loop system stability. In addition, the proposed algorithm can also be applied to polar alignment. The performance of the proposed algorithm is verified by both simulations and experiments and the results exhibit the superior performance of the proposed approach. PMID:27136565

  4. Performance Reports: Mirror alignment system performance prediction comparison between SAO and EKC

    NASA Technical Reports Server (NTRS)

    Tananbaum, H. D.; Zhang, J. P.

    1994-01-01

    The objective of this study is to perform an independent analysis of the residual high resolution mirror assembly (HRMA) mirror distortions caused by force and moment errors in the mirror alignment system (MAS) to statistically predict the HRMA performance. These performance predictions are then compared with those performed by Kodak to verify their analysis results.

  5. Alignment in Complex Education Systems: Achieving Balance and Coherence. OECD Education Working Papers, Number 64

    ERIC Educational Resources Information Center

    Looney, Janet W.

    2011-01-01

    The majority of OECD countries now implement one form or another of standards-based assessment and evaluation. The core logic of standards-based systems rests upon the alignment of three key elements: "standards" defining the knowledge and skills--or "competences"--students are expected to have attained at different stages of their education;…

  6. A Sense of Balance: District Aligns Personalized Learning with School and System Goals

    ERIC Educational Resources Information Center

    Donsky, Debbie; Witherow, Kathy

    2015-01-01

    This article addresses the challenge of personalizing learning while also ensuring alignment with system and school improvement plans. Leaders of the York Region District School Board in Ontario knew that what took their high-performing school district from good to great would not take it from great to excellent. The district's early model of…

  7. Terminator field-aligned current system: Its dependencies on solar, seasonal, and geomagnetic conditions

    NASA Astrophysics Data System (ADS)

    Zhu, L.; Schunk, R. W.; Eccles, V.; Scherliess, L.; Sojka, J. J.; Gardner, L. C.

    2014-12-01

    A new field-aligned current system in the high-latitude ionosphere was reported recently by Zhu et al. (2014). The current system develops and evolves along the ionospheric terminator and it is thus termed as the terminator field-aligned currents. The discovery was based on the reconstructions from the Ionospheric Dynamics and Electrodynamics Data Assimilation Model (IDED-DA) with the ingestion of observational measurements. In this presentation, we show the results of a follow-on study using the IDED-DA, in which the solar, seasonal, and geomagnetic dependencies of the terminator field-aligned currents are explored. The new current system is the first field-aligned current system in the high-latitude ionosphere that is not directly driven by the magnetospheric dynamics and has an ionospheric origin. A systematic study of its electrodynamic and plasma dynamics as well as dependencies on various solar-terrestrial conditions will help us to explore the active role of the ionosphere in the magnetosphere-ionosphere coupling and improve the physical understanding of the electrodynamics and plasma dynamics of many small-scale structures in the polar ionosphere.

  8. An Improved Alignment Method for the Strapdown Inertial Navigation System (SINS).

    PubMed

    Liu, Meng; Gao, Yanbin; Li, Guangchun; Guang, Xingxing; Li, Shutong

    2016-01-01

    In this paper, an innovative inertial navigation system (INS) mechanization and the associated Kalman filter (KF) are developed to implement a fine alignment for the strapdown INS (SINS) on stationary base. The improved mechanization is established in the pseudo-geographic frame, which is rebuilt based on the initial position. The new mechanization eliminates the effects of linear movement errors on the heading by decoupling. Compared with the traditional local-level mechanization, it has more advantages. The proposed algorithm requires lower coarse alignment accuracy in both the open-loop and closed-loop KFs and hence can improve the system reliability and decrease the total alignment time. Moreover, for the closed-loop KF, it can decrease oscillation caused by the system errors and improve the closed-loop system stability. In addition, the proposed algorithm can also be applied to polar alignment. The performance of the proposed algorithm is verified by both simulations and experiments and the results exhibit the superior performance of the proposed approach. PMID:27136565

  9. Cognitive-Behavioral Analysis System of Psychotherapy as a Maintenance Treatment for Chronic Depression

    ERIC Educational Resources Information Center

    Klein, Daniel N.; Santiago, Neil J.; Vivian, Dina; Blalock, Janice A.; Kocsis, James H.; Markowitz, John C.; McCullough, James P., Jr.; Rush, John A.; Trivedi, Madhukar H.; Arnow, Bruce A.; Dunner, David L.; Manber, Rachel; Rothbaum, Barbara; Thase, Michael E.; Keitner, Gabor I.; Miller, Ivan W.; Keller, Martin B.

    2004-01-01

    Although the efficacy of maintenance pharmacotherapy for the prevention of recurrence in major depressive disorder (MDD) is well documented, few studies have tested the efficacy of psychotherapy as a maintenance treatment. The authors examined the efficacy of the cognitive-behavioral analysis system of psychotherapy (CBASP) as a maintenance…

  10. EX.MAIN. Expert System Model for Maintenance and Staff Training.

    ERIC Educational Resources Information Center

    Masturzi, Elio R.

    EX.MAIN, a model for maintenance and staff training which combines knowledge based expert systems and computer based training, was developed jointly by the Department of Production Engineering of the University of Naples and CIRCUMVESUVIANA, the largest private railroad in Italy. It is a global model in the maintenance field which contains both…

  11. Monitoring Strategies in Permeable Pavement Systems to Optimize Maintenance Scheduling - abstract

    EPA Science Inventory

    As the surface in a permeable pavement system clogs and performance decreases, maintenance is required to preserve the design function. Currently, guidance is limited for scheduling maintenance on an as needed basis. Previous research has shown that surface clogging in a permea...

  12. 14 CFR 1212.601 - Maintenance and publication requirements for systems of records.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Maintenance and publication requirements... ADMINISTRATION PRIVACY ACT-NASA REGULATIONS Instructions for NASA Employees § 1212.601 Maintenance and...) Maintain any record in a system of records for necessary and lawful purposes only, assure that...

  13. A non-contacting vertical alignment system for mass properties measuring instruments

    SciTech Connect

    James, G.H. III; Suazo, J.E.; Varga, R.C.

    1993-11-01

    A non-contact system for alignment of objects on mass properties measuring instruments is described. Test parts can be aligned to within the capabilities of the user and the fixture to make the adjustments. The current implementation can align objects to less than .001 inches at two points with final requested adjustments of a few ten-thousands of an inch. The non-contact capability allows the alignment of objects which are too compliant or fragile for traditional contacting measurement methods. Also, this system allows the definition of a reference axis on objects which are not perfectly symmetric. The reference axis is defined at the top of the object by an appropriate marker and defined at the bottom by a best fit circle through the surface at a specified height. A general description of the hardware, procedures, and results are presented for the non-user. Appendices which contain a complete description of the software, usage, and mathematical implementation are provided for the reader who is interested in using or further developing the system.

  14. The data collection system for failure/maintenance at the tritium systems test assembly

    SciTech Connect

    Casey, M.A.; Gruetzmacher, K.M.; Bartlit, J.R.; Cadwallader, L.C.

    1988-09-01

    A data collection system for obtaining information which can be used to help determine the reliability and availability of future fusion power plants has been installed at the Los Alamos National Laboratory's Tritium Systems Test Assembly (TSTA). Failure and maintenance data on components of TSTA's tritium systems have been collected since 1984. The focus of the data collection has been TSTA's Tritium Waste Treatment System (TWT), which has maintained high availability since it became operational in 1982. Data collection is still in progress and a total of 291 failure reports are in the data collection system at this time, 47 of which are from the TWT.

  15. The data collection system for failure/maintenance at the Tritium Systems Test Assembly

    SciTech Connect

    Casey, M.A.; Gruetzmacher, K.M.; Bartlit, J.R.; Cadwallader, L.C.

    1988-01-01

    A data collection system for obtaining information which can be used to help determine the reliability and vailability of future fusion power plants has been installed at the Los Alamos National Laboratory's Tritium Systems Test Assembly (TSTA). Failure and maintenance data on components of TSTA's tritium systems have been collected since 1984. The focus of the data collection has been TSTA's Tritium Waste Tratment System (TWT), which has maintained high availability since it became operation in 1982. Data collection is still in progress and a total of 291 failure reports are in the data collection system at this time, 47 of which are from the TWT. 6 refs., 2 figs., 2 tabs.

  16. THE BANANA PROJECT. IV. TWO ALIGNED STELLAR ROTATION AXES IN THE YOUNG ECCENTRIC BINARY SYSTEM EP CRUCIS: PRIMORDIAL ORIENTATION AND TIDAL ALIGNMENT

    SciTech Connect

    Albrecht, Simon; Winn, Joshua N.; Setiawan, Johny; Torres, Guillermo; Fabrycky, Daniel C.

    2013-04-10

    With observations of the EP Cru system, we continue our series of measurements of spin-orbit angles in eclipsing binary star systems, the BANANA project (Binaries Are Not Always Neatly Aligned). We find a close alignment between the sky projections of the rotational and orbital angular momentum vectors for both stars ({beta}{sub p} = -1. Degree-Sign 8 {+-} 1. Degree-Sign 6 and |{beta}{sub s}| < 17 Degree-Sign ). We also derive precise absolute dimensions and stellar ages for this system. The EP Cru and DI Her systems provide an interesting comparison: they have similar stellar types and orbital properties, but DI Her is younger and has major spin-orbit misalignments, raising the question of whether EP Cru also had a large misalignment at an earlier phase of evolution. We show that tidal dissipation is an unlikely explanation for the good alignment observed today, because realignment happens on the same timescale as spin-orbit synchronization, and the stars in EP Cru are far from synchronization (they are spinning nine times too quickly). Therefore it seems that some binaries form with aligned axes, while other superficially similar binaries are formed with misaligned axes.

  17. GOES data-collection system instrumentation, installation, and maintenance manual

    USGS Publications Warehouse

    Blee, J.W.; Herlong, H.E.; Kaufmann, C.D., Jr.; Hardee, J.H.; Field, M.L.; Middelburg, R.F.

    1986-01-01

    The purpose of the manual is to describe the installation, operation, and maintenance of Geostationary Operational Environmental Satellite (GOES) data collection platforms (DCP's) and associated equipment. This manual is not a substitute for DCP manufacturers ' manuals but is additional material that describes the application of data-collection platforms in the Water Resources Division. Power supplies, encoders, antennas, Mini Monitors, voltage analog devices, and the installation of these at streamflow-gaging stations are discussed in detail. (USGS)

  18. A resistive heating system for homeothermic maintenance in small animals

    PubMed Central

    Kersemans, Veerle; Gilchrist, Stuart; Allen, Philip D.; Beech, John S.; Kinchesh, Paul; Vojnovic, Borivoj; Smart, Sean C.

    2015-01-01

    Purpose To develop an MR-compatible resistive heater for temperature maintenance of anaesthetized animals. Materials and Methods An MR-compatible resistive electrical heater was formed from a tightly-wound twisted pair wire, interfaced to a homeothermic maintenance controller. Fat-suppressed images and localized spectra were acquired with the twisted pair heater and a near-identical single strand heater during operation at maximum power. Data were also acquired in the absence of heating to demonstrate the insensitivity of MR to distortions arising from the passage of current through the heater elements. The efficacy of temperature maintenance was examined by measuring rectal temperature immediately following induction of general anesthesia and throughout and after the acquisition of a heater artifact-prone image series. Results Images and spectra acquired in the presence and absence of DC current through the twisted pair heater were identical whereas the passage of current through the single strand wire created field shifts and lineshape distortions. Temperature that is lost during anesthesia induction was recovered within approximately 10–20 minutes of induction, and a stable temperature is reached as the animal's temperature approaches the set target. Conclusion The twisted pair wire heater does not interfere with MR image quality and maintains adequate thermal input to the animal to maintain body temperature. PMID:25863135

  19. An Integrated Support and Alignment System for Large ILC Lattice Elements

    SciTech Connect

    Viola, Robert

    2013-05-15

    The manipulators used to support and position lattice elements are critical components of all particle accelerators. The increased use of large superconducting magnets and accelerator modules places even greater demands on these manipulators. However, the performance of these support systems has not kept pace with the advances made in other areas of accelerator technology. This results in accelerators that are difficult to align and may not be capable of achieving target luminosities. An innovative new type of positioning mechanism tailored to the requirements of the International Linear Collider is proposed. The Tri-Sphere System provides secure support for large lattice elements and precision adjustment in six degrees of freedom. Integrated target sockets allow the support system to be rapidly pre-aligned. The system's kinematic design passively guides lattice elements into their correct location during installation. A complimentary Portable Actuation Unit provides the advantages of automated adjustment and allows these adjustments to be completely decoupled from surveying.

  20. Automated sample mounting and alignment system for biological crystallography at a synchrotron source.

    PubMed

    Snell, Gyorgy; Cork, Carl; Nordmeyer, Robert; Cornell, Earl; Meigs, George; Yegian, Derek; Jaklevic, Joseph; Jin, Jian; Stevens, Raymond C; Earnest, Thomas

    2004-04-01

    High-throughput data collection for macromolecular crystallography requires an automated sample mounting and alignment system for cryo-protected crystals that functions reliably when integrated into protein-crystallography beamlines at synchrotrons. Rapid mounting and dismounting of the samples increases the efficiency of the crystal screening and data collection processes, where many crystals can be tested for the quality of diffraction. The sample-mounting subsystem has random access to 112 samples, stored under liquid nitrogen. Results of extensive tests regarding the performance and reliability of the system are presented. To further increase throughput, we have also developed a sample transport/storage system based on "puck-shaped" cassettes, which can hold sixteen samples each. Seven cassettes fit into a standard dry shipping Dewar. The capabilities of a robotic crystal mounting and alignment system with instrumentation control software and a relational database allows for automated screening and data collection to be developed. PMID:15062077

  1. Optical development system lab alignment solutions for the ICESat-2 ATLAS instrument

    NASA Astrophysics Data System (ADS)

    Evans, T.

    The ATLAS Instrument for the ICESat-2 mission at NASA's Goddard Space Flight Center requires an alignment test-bed to prove out new concepts. The Optical Development System (ODS) lab was created to test prototype models of individual instrument components to simulate how they will act as a system. The main ICESat-2 instrument is the Advanced Topographic Laser Altimeter System (ATLAS). It measures ice elevation by transmitting laser pulses, and collecting the reflection in a telescope. Because the round trip time is used to calculate distance, alignment between the outgoing transmitter beam and the incoming receiver beams are critical. An automated closed loop monitoring control system is currently being tested at the prototype level to prove out implementation for the final spacecraft. To achieve an error of less than 2 micro-radians, an active deformable mirror was used to correct the lab wave front from the collimated “ ground reflection” beam. The lab includes a focal plane assembly set up, a one meter diameter collimator optic, and a 0.8 meter flight spare telescope for alignment. ATLAS prototypes and engineering models of transmitter and receiver optics and sub-systems are brought in to develop and integrate systems as well as write procedures to be used in integration and testing. By having a fully integrated system with prototypes and engineering units, lessons can be learned before flight designs are finalized.

  2. Method for auto-alignment of digital optical phase conjugation systems based on digital propagation

    PubMed Central

    Jang, Mooseok; Ruan, Haowen; Zhou, Haojiang; Judkewitz, Benjamin; Yang, Changhuei

    2014-01-01

    Optical phase conjugation (OPC) has enabled many optical applications such as aberration correction and image transmission through fiber. In recent years, implementation of digital optical phase conjugation (DOPC) has opened up the possibility of its use in biomedical optics (e.g. deep-tissue optical focusing) due to its ability to provide greater-than-unity OPC reflectivity (the power ratio of the phase conjugated beam and input beam to the OPC system) and its flexibility to accommodate additional wavefront manipulations. However, the requirement for precise (pixel-to-pixel matching) alignment of the wavefront sensor and the spatial light modulator (SLM) limits the practical usability of DOPC systems. Here, we report a method for auto-alignment of a DOPC system by which the misalignment between the sensor and the SLM is auto-corrected through digital light propagation. With this method, we were able to accomplish OPC playback with a DOPC system with gross sensor-SLM misalignment by an axial displacement of up to~1.5 cm, rotation and tip/tilt of ~5∘, and in-plane displacement of ~5 mm (dependent on the physical size of the sensor and the SLM). Our auto-alignment method robustly achieved a DOPC playback peak-to-background ratio (PBR) corresponding to more than ~30 % of the theoretical maximum. As an additional advantage, the auto-alignment procedure can be easily performed at will and, as such, allows us to correct for small mechanical drifts within the DOPC systems, thus overcoming a previously major DOPC system vulnerability. We believe that this reported method for implementing robust DOPC systems will broaden the practical utility of DOPC systems. PMID:24977504

  3. System design and implementation for the glass panel alignment and sealing tool for flat panel displays

    SciTech Connect

    Jordan, J.D.; Stromberg, P.G.; Kuszmaul, S.S.

    1996-10-16

    This report describes the system designed and fabricated for the National Center for Advanced Information Component Manufacturing (NCAICM) project number 9322-135. The system is a device capable of simultaneously aligning two glass plates and sealing them together with glass frit. The process development was divided into two phases. The first was thermal sealing in an ambient environment. The second was sealing a controlled environment in a vacuum.

  4. Method for auto-alignment of digital optical phase conjugation systems based on digital propagation.

    PubMed

    Jang, Mooseok; Ruan, Haowen; Zhou, Haojiang; Judkewitz, Benjamin; Yang, Changhuei

    2014-06-16

    Optical phase conjugation (OPC) has enabled many optical applications such as aberration correction and image transmission through fiber. In recent years, implementation of digital optical phase conjugation (DOPC) has opened up the possibility of its use in biomedical optics (e.g. deep-tissue optical focusing) due to its ability to provide greater-than-unity OPC reflectivity (the power ratio of the phase conjugated beam and input beam to the OPC system) and its flexibility to accommodate additional wavefront manipulations. However, the requirement for precise (pixel-to-pixel matching) alignment of the wavefront sensor and the spatial light modulator (SLM) limits the practical usability of DOPC systems. Here, we report a method for auto-alignment of a DOPC system by which the misalignment between the sensor and the SLM is auto-corrected through digital light propagation. With this method, we were able to accomplish OPC playback with a DOPC system with gross sensor-SLM misalignment by an axial displacement of up to~1.5 cm, rotation and tip/tilt of ~5° and in-plane displacement of ~5 mm (dependent on the physical size of the sensor and the SLM). Our auto-alignment method robustly achieved a DOPC playback peak-to-background ratio (PBR) corresponding to more than ~30 % of the theoretical maximum. As an additional advantage, the auto-alignment procedure can be easily performed at will and, as such, allows us to correct for small mechanical drifts within the DOPC systems, thus overcoming a previously major DOPC system vulnerability. We believe that this reported method for implementing robust DOPC systems will broaden the practical utility of DOPC systems. PMID:24977504

  5. Alignment performance comparison between MFR and MDCO for a TMA optical system

    NASA Astrophysics Data System (ADS)

    Kang, Hyukmo; Oh, Eunsong; Kim, Sug-Whan

    2015-09-01

    In this study, we performed alignment state estimation simulations and compared the performance of two Computer Aided Alignment (hereafter CAA) algorithms i.e. `Merit Function Regression (MFR)' and `Multiple Design Configuration Optimization (MDCO)' for a TMA optical system. The former minimizes the merit function using multi-field wavefront error measurements from single configuration, while the latter minimizes the merit function using single-field measured wavefront error from multiple configurations. The optical system used is an unobscured three-mirror anastigmat (TMA) optical system of 70mm in diameter, and F/5.0. It is designed for an unmanned aerial vehicle for coastal water remote sensing. The TMA consists of two aspherical mirrors, a spherical mirror and a flat folding mirror. Based on the sensitivity analysis, we set the tilt x, y of tertiary mirror as a compensator, and not considered decenter of tertiary mirror because of its spherical characteristic. For the simulation, we introduced Gaussian distribution of initial misalignment to M3. It has the mean value of zero and standard deviation of 0.5 mrad. The initial simulation result of alignment state estimation shows that both algorithms can meet the alignment requirement, λ/10 RMS WFE at 633nm. However, when we includes measurement noise, the simulation result of MFR shows greater standard deviation in RMS WFE than that of MDCO. As for the measurement, the MDCO requires single on-axis field while the MFR requires multiple fields, we concluded that the MDCO is more practical method to align the off-axis TMA optics than MFR.

  6. Advanced remote handling for future applications: The advanced integrated maintenance system

    SciTech Connect

    Herndon, J.N.; Kring, C.T.; Rowe, J.C.

    1986-01-01

    The Consolidated Fuel Reprocessing Program at Oak Ridge National Laboratory has been developing advanced techniques for remote maintenance of future US fuel reprocessing plants. The developed technology has a wide spectrum of application for other hazardous environments. These efforts are based on the application of teleoperated, force-reflecting servomanipulators for dexterous remote handling with television viewing for large-volume hazardous applications. These developments fully address the nonrepetitive nature of remote maintenance in the unstructured environments encountered in fuel reprocessing. This paper covers the primary emphasis in the present program; the design, fabrication, installation, and operation of a prototype remote handling system for reprocessing applications, the Advanced Integrated Maintenance System.

  7. A remote telepresence robotic system for inspection and maintenance of a nuclear power plant

    SciTech Connect

    Crane, C.D. III; Tulenko, J.S.

    1993-02-01

    Progress in reported in the areas of environmental hardening; database/world modeling; man-machine interface; development of the Advanced Liquid Metal Reactor (ALMR) maintenance inspection robot design; and Articulated Transporter/Manipulator System (ATMS) development.

  8. Design, fabrication, delivery, operation and maintenance of a geothermal power conversion system

    NASA Technical Reports Server (NTRS)

    1980-01-01

    The design, fabrication, delivery, operation and maintenance of an Hydrothermal Power Company 1250 KVA geothermal power conversion system using a helical screw expander as the prime mover is described. Hydrostatic and acceptance testing are discussed.

  9. Economy In Expert System Construction: The AEGIS Combat System Maintenance Advisor

    NASA Astrophysics Data System (ADS)

    Drastal, George; DuBois, Tom; McAndrews, Lorin; Raatz, Stan; Straguzzi, Nick

    1986-03-01

    We present the design philosophy used in constructing the AEGIS Combat System Maintenance Advisor, a rule-based expert system with over 2000 rules that was completed in less than two years. We attribute part of the success of this project to the decision to have the domain expert actively involved in the process of writing rules, and to the development of a knowledge acquisition tool that checked his work. The project was also noteworthy because it includes a compiler which retargets the knowledge base to alternate run-time environments. The techniques used in this project are general and apply to any propositional rule language for expert systems.

  10. Automated System Checkout to Support Predictive Maintenance for the Reusable Launch Vehicle

    NASA Technical Reports Server (NTRS)

    Patterson-Hine, Ann; Deb, Somnath; Kulkarni, Deepak; Wang, Yao; Lau, Sonie (Technical Monitor)

    1998-01-01

    The Propulsion Checkout and Control System (PCCS) is a predictive maintenance software system. The real-time checkout procedures and diagnostics are designed to detect components that need maintenance based on their condition, rather than using more conventional approaches such as scheduled or reliability centered maintenance. Predictive maintenance can reduce turn-around time and cost and increase safety as compared to conventional maintenance approaches. Real-time sensor validation, limit checking, statistical anomaly detection, and failure prediction based on simulation models are employed. Multi-signal models, useful for testability analysis during system design, are used during the operational phase to detect and isolate degraded or failed components. The TEAMS-RT real-time diagnostic engine was developed to utilize the multi-signal models by Qualtech Systems, Inc. Capability of predicting the maintenance condition was successfully demonstrated with a variety of data, from simulation to actual operation on the Integrated Propulsion Technology Demonstrator (IPTD) at Marshall Space Flight Center (MSFC). Playback of IPTD valve actuations for feature recognition updates identified an otherwise undetectable Main Propulsion System 12 inch prevalve degradation. The algorithms were loaded into the Propulsion Checkout and Control System for further development and are the first known application of predictive Integrated Vehicle Health Management to an operational cryogenic testbed. The software performed successfully in real-time, meeting the required performance goal of 1 second cycle time.

  11. Design and performance of the alignment system for the CMS muon endcaps

    SciTech Connect

    Hohlmann, Marcus; Baksay, Gyongyi; Browngold, Max; Dehmelt, Klaus; Guragain, Samir; Andreev, Valery; Yang, Xiaofeng; Bellinger, James; Carlsmith, Duncan; Feyzi, Farshid; Loveless, Richard J.; /Florida Inst. Tech. /UCLA /Wisconsin U., Madison /UC, Davis /Fermilab /St. Petersburg, INP /UC, Riverside

    2006-12-01

    The alignment system for the CMS Muon Endcap detector employs several hundred sensors such as optical 1-D CCD sensors illuminated by lasers and analog distance- and tilt-sensors to monitor the positions of one sixth of 468 large Cathode Strip Chambers. The chambers mounted on the endcap yoke disks undergo substantial deformation on the order of centimeters when the 4T field is switched on and off. The Muon Endcap alignment system is required to monitor chamber positions with 75-200 {micro}m accuracy in the R? plane, {approx}400 {micro}m in the radial direction, and {approx}1 mm in the z-direction along the beam axis. The complete alignment hardware for one of the two endcaps has been installed at CERN. A major system test was performed when the 4T solenoid magnet was ramped up to full field for the first time in August 2006. We present the overall system design and first results on disk deformations, which indicate that the measurements agree with expectations.

  12. Optical alignment influenced aberrations in laser beam delivery systems and their correction

    NASA Astrophysics Data System (ADS)

    Scaggs, Michael; Haas, Gil

    2015-03-01

    Industrial high power laser systems are often evaluated based upon spatial profile of the beam before they are brought to focus for processing materials. It is therefore often assumed that if the raw beam profile is good that the focus is equally as good. The possibility of having good optics and poor alignment or bad optics and good alignment and therefore not achieve a good focal spot is quite high due to the fact that a raw beam spatial profile does not manifest third order aberrations. In such instances the focal spot will contain aberrations when there are slightly misaligned, poor quality, high power optics in the system such as a beam expander or eye piece and objective of a 3-axis galvo. Likewise, if the beam itself is not on axis, the third order aberrations of astigmatism and coma are likely to appear but again not be seen in the unfocused beams spatial profile. The third order aberrations of astigmatism, coma and spherical aberration can significantly alter both the size and spatial profile at the focus resulting in out of spec performance. The impact of beam and zoom expanders and their alignment in beam delivery systems is investigated by measuring both the far field unfocused and the far field focus beams using an all passive beam waist analyzer system.

  13. Centroid Detector Assembly for the AXAF-I Alignment Test System

    NASA Technical Reports Server (NTRS)

    Glenn, Paul

    1995-01-01

    The High Resolution Mirror Assembly (HRMA) of the Advanced X-ray Astrophysics Facility (imaging) (AXAF-I) consists of four nested paraboloids and four nested hyperboloids, all of meter-class size, and all of which are to be assembled and aligned in a special 15 meter tower at Eastman Kodak Company in Rochester, NY. The goals of the alignment are (1) to make the images of the four telescopes coincident; (2) to remove coma from each image individually; and (3) to control and determine the final position of the composite focus. This will be accomplished by the HRMA Aligment Test System (HATS) which is essentially a scanning Hartmann test system. The scanning laser source and the focal plane of the HATS are part of the Centroid Detector Assembly (CDA) which also includes processing electronics and software. In this paper we discuss the design and the measured performance of the CDA.

  14. Alignment and integration of large optical systems based on advanced metrology.

    NASA Astrophysics Data System (ADS)

    Aliverti, M.; Riva, M.; Moschetti, M.; Pariani, G.; Genoni, M.; Zerbi, F. M.

    Optical alignment is a key activity in opto-mechanical system Integration. Traditional techniques require adjustable mounting, driven by optical references that allows the tuning of the optics position along all 6 Degree of Freedom. Nevertheless, the required flexibility imposes reduced stiffness and consequently less stability of the system. The Observatory of Brera (OAB) started few years ago a research activity focused onto the overcoming of this limits exploiting the high metrology performances of Coordinate Measuring Machines (CMM) with the main objectives of relax the manufacturing tolerances and maximize mounting stiffness. Through the T-REX grants, OAB acquired all the instrumentation needed for that activity furthermore considering the ESPRESSO project training and testing also oriented to large scale instrumentation like the E-ELT one. We will present in this paper the definition of the VLTs convergence point and the feasibility study of large mirrors alignment done by mechanical measurements methods. skip=8pt

  15. Research on gesture recognition of augmented reality maintenance guiding system based on improved SVM

    NASA Astrophysics Data System (ADS)

    Zhao, Shouwei; Zhang, Yong; Zhou, Bin; Ma, Dongxi

    2014-09-01

    Interaction is one of the key techniques of augmented reality (AR) maintenance guiding system. Because of the complexity of the maintenance guiding system's image background and the high dimensionality of gesture characteristics, the whole process of gesture recognition can be divided into three stages which are gesture segmentation, gesture characteristic feature modeling and trick recognition. In segmentation stage, for solving the misrecognition of skin-like region, a segmentation algorithm combing background mode and skin color to preclude some skin-like regions is adopted. In gesture characteristic feature modeling of image attributes stage, plenty of characteristic features are analyzed and acquired, such as structure characteristics, Hu invariant moments features and Fourier descriptor. In trick recognition stage, a classifier based on Support Vector Machine (SVM) is introduced into the augmented reality maintenance guiding process. SVM is a novel learning method based on statistical learning theory, processing academic foundation and excellent learning ability, having a lot of issues in machine learning area and special advantages in dealing with small samples, non-linear pattern recognition at high dimension. The gesture recognition of augmented reality maintenance guiding system is realized by SVM after the granulation of all the characteristic features. The experimental results of the simulation of number gesture recognition and its application in augmented reality maintenance guiding system show that the real-time performance and robustness of gesture recognition of AR maintenance guiding system can be greatly enhanced by improved SVM.

  16. Installation, operation, and maintenance for the pyramidal optics solar system installed at Yacht Cover, Columbia, South Carolina

    NASA Technical Reports Server (NTRS)

    1980-01-01

    Information concerning the installation, operation, and maintenance of the pyramidal Solar System for space heating and domestic hot water is presented. Principles of operation, sequence of installation, and procedures for the operation and maintenance of each subsystem making up the solar system are presented. Troubleshooting charts and maintenance schedules are presented.

  17. Installation, operation, and maintenance for the pyramidal optics solar system installed at Yacht Cover, Columbia, South Carolina

    NASA Astrophysics Data System (ADS)

    1980-09-01

    Information concerning the installation, operation, and maintenance of the pyramidal Solar System for space heating and domestic hot water is presented. Principles of operation, sequence of installation, and procedures for the operation and maintenance of each subsystem making up the solar system are presented. Troubleshooting charts and maintenance schedules are presented.

  18. 42 CFR 414.1225 - Alignment of Physician Quality Reporting System quality measures and quality measures for the...

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 42 Public Health 3 2013-10-01 2013-10-01 false Alignment of Physician Quality Reporting System quality measures and quality measures for the value-based payment modifier. 414.1225 Section 414.1225... Payment Modifier Under the Physician Fee Schedule § 414.1225 Alignment of Physician Quality...

  19. 42 CFR 414.1225 - Alignment of Physician Quality Reporting System quality measures and quality measures for the...

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 42 Public Health 3 2014-10-01 2014-10-01 false Alignment of Physician Quality Reporting System quality measures and quality measures for the value-based payment modifier. 414.1225 Section 414.1225... Payment Modifier Under the Physician Fee Schedule § 414.1225 Alignment of Physician Quality...

  20. Computerized "drag-and-drop" alignment of GPC-based optical micromanipulation system.

    PubMed

    Dam, Jeppe Seidelin; Rodrigo, Peter John; Perch-Nielsen, Ivan R; Alonzo, Carlo Amadeo; Glückstad, Jesper

    2007-02-19

    In the past, aligning the counterpropagating beams in our 3D real-time generalized phase contrast (GPC) trapping system has been a task requiring moderate skills and prior experience with optical instrumentation. A ray transfer matrix analysis and computer-controlled actuation of mirrors, objective, and sample stage has made this process user friendly. The alignment procedure can now be done in a very short time with just a few drag-and-drop tasks in the user-interface. The future inclusion of an image recognition algorithm will allow the alignment process to be executed completely without any user interaction. An automated sample loading tray with a loading precision of a few microns has also been added to simplify the switching of samples under study. These enhancements have significantly reduced the level of skill and experience required to operate the system, thus making the GPC-based micromanipulation system more accessible to people with little or no technical expertise in optics. PMID:19532431

  1. Orbital assembly and maintenance study

    NASA Technical Reports Server (NTRS)

    Gorman, D.; Grant, C.; Kyrias, G.; Lord, C.; Rombach, J.; Salis, M.; Skidmore, R.; Thomas, R.

    1975-01-01

    The requirements, conceptual design, tradeoffs, procedures, and techniques for orbital assembly of the support structure of the microwave power transmission system and the radio astronomy telescope are described. Thermal and stress analyses, packaging, alignment, and subsystems requirements are included along with manned vs. automated and transportation tradeoffs. Technical and operational concepts for the manned and automated maintenance of satellites were investigated and further developed results are presented.

  2. Development of an automated checkout, service and maintenance system for a Space Station EVAS

    NASA Technical Reports Server (NTRS)

    Abeles, Fred J.; Tri, Terry; Blaser, Robert

    1988-01-01

    The development of a new operational system for the Space Station will minimize the time normally spent on performing on-orbit checkout, servicing, and maintenance of an extravehicular activity system of the Space Station. This system, the Checkout, Servicing, and Maintenance System (COSM), is composed of interactive control software interfacing with software simulations of hardware components. The major elements covered in detail include the controller, the EMU simulator and the regenerative life support system. The operational requirements and interactions of the individual elements as well as the protocols are also discussed.

  3. Research on Initial Alignment and Self-Calibration of Rotary Strapdown Inertial Navigation Systems

    PubMed Central

    Gao, Wei; Zhang, Ya; Wang, Jianguo

    2015-01-01

    The errors of inertial sensors affect the navigation accuracy of the strapdown inertial navigation system (SINS) and are accumulated over time in nature. In order to continuously maintain the high navigation accuracy of vehicles for a long time period, an initial alignment and self-calibration is necessary after the SINS starts. Additionally, the observability analysis is one of the key techniques during the initial alignment and self-calibration process. For marine systems, the observability of inertial sensor errors is extremely low, as their motion states are always slow. Therefore, studying the rotating SINS is urgent. Since traditional analysis methods have their limitations, the global observation analysis method was used in this paper. On the basis of this method, the relationship between the observability and the kinestate of the rotating SINS has been established. After the discussion about the factors that affect the observability in detail, the design principle of the initial alignment and self-calibration rotating scheme, which is appropriate for marine systems, id proposed. With the proposed principle, a novel initial alignment and self-calibration method, named the eight-position rotating scheme, is designed. Simulations and experiments are carried out to verify its performance. The results have shown that compared with other rotating schemes and the static state, the estimated accuracy of the eight-position scheme rotating about axes x and y was the best, and the position error was significantly reduced with this new rotating scheme. The feasibility and effectiveness of the proposed design principle and the rotating scheme were verified. PMID:25647743

  4. Design of a decision support system for preventive maintenance planning in health structures.

    PubMed

    Miniati, Roberto; Dori, Fabrizio; Gentili, Guido Biffi

    2012-01-01

    The appropriate maintenance of medical devices, including performance inspections and preventive maintenance, is fundamental in mitigating clinical risk caused by adverse events in health care. Although several models for managing and planning preventive maintenance have been developed, the problem is lacking in standard methodology and still presents an open challenge for today's health experts. This paper aims to provide and develop methodology together with support systems able to assist decision makers in constructing preventive maintenance and performance inspection plans, taking into account both the technical and economic needs of hospital clinical engineering departments. Interventions by decision makers are of crucial importance within complex situations where large numbers, types of devices and different contractual situations are involved. SISMA system has achieved optimal results with minimum expense and maximum security for patients and technicians at the University Hospital of Florence where it has been applied in actual case studies. PMID:22735735

  5. Maintenance manual for the Beneficial Uses Shipping System cask. Revision 1

    SciTech Connect

    Bronowski, D.R.; Yoshimura, H.R.

    1993-05-01

    This document is the Maintenance Manual for the Beneficial Uses Shipping System (BUSS) cask. These instructions address requirements for maintenance, inspection, testing, and repair, supplementing general information found in the BUSS Safety Analysis Report for Packaging (SARP), SAND 83-0698. Use of the BUSS cask is authorized by the Department of Energy (DOE) and the Nuclear Regulatory Commission (NRC) for the shipment of special form cesium chloride or strontium flouride capsules.

  6. An autocollimator alignment system for a Schwarzschild-Couder Cherenkov telescope

    NASA Astrophysics Data System (ADS)

    Griffiths, S. T.; Kaaret, P.; Smith, E.

    2016-08-01

    We present a digital autocollimator which will be used in the alignment system of a prototype medium-sized telescope, which is part of the U.S. contribution to the Cherenkov Telescope Array (CTA). The Schwarzschild-Couder optics in the prototype telescope (which is currently under construction) requires the precise alignment of three components: the primary and secondary segmented mirrors, and the gamma-ray camera. The approximately 9 meter separation between the mirrors necessitates remote optical measurement. Our autocollimator will measure the angle of a segment in one mirror relative to the center of the other mirror with a precision better than 5 arcsec over a range of ±0.126 °. We present a detailed description of the instrument and describe its performance in the laboratory.

  7. An autocollimator alignment system for a Schwarzschild-Couder Cherenkov telescope

    NASA Astrophysics Data System (ADS)

    Griffiths, S. T.; Kaaret, P.; Smith, E.

    2016-04-01

    We present a digital autocollimator which will be used in the alignment system of a prototype medium-sized telescope, which is part of the U.S. contribution to the Cherenkov Telescope Array (CTA). The Schwarzschild-Couder optics in the prototype telescope (which is currently under construction) requires the precise alignment of three components: the primary and secondary segmented mirrors, and the gamma-ray camera. The approximately 9 meter separation between the mirrors necessitates remote optical measurement. Our autocollimator will measure the angle of a segment in one mirror relative to the center of the other mirror with a precision better than 5 arcsec over a range of ±0.126°. We present a detailed description of the instrument and describe its performance in the laboratory.

  8. Advanced Ground Systems Maintenance Physics Models for Diagnostics Project

    NASA Technical Reports Server (NTRS)

    Harp, Janicce Leshay

    2014-01-01

    The project will use high-fidelity physics models and simulations to simulate real-time operations of cryogenic and systems and calculate the status/health of the systems. The project enables the delivery of system health advisories to ground system operators. The capability will also be used to conduct planning and analysis of cryogenic system operations.

  9. Very high stability systems: LMJ target alignment system and MTG imager test setup

    NASA Astrophysics Data System (ADS)

    Compain, Eric; Maquet, Philippe; Kunc, Thierry; Marque, Julien; Lauer-Solelhac, Maxime; Delage, Laurent; Lanternier, Catherine

    2015-09-01

    Most of space instruments and research facilities require test equipment with demanding opto-mechanical stability. In some specific cases, when the stability performance directly drives the final performance of the scientific mission and when feasibility is questionable, specific methods must be implemented for the associated technical risk management. In present paper, we will present our heritage in terms of methodology, design, test and the associated results for two specific systems : the SOPAC-POS and the MOTA, generating new references for future developments. From a performance point of view, we will emphasis on following key parameters : design symmetry, thermal load management, and material and structural choices. From a method point of view the difficulties arise first during design, from the strong coupling between the thermal, mechanical and optical performance models, and then during testing, from the difficulty of conceiving test setup having appropriate performance level. We will present how these limitations have been overcome. SOPAC-POS is the target alignment system of the LMJ, Laser Mega Joule, the French inertial confinement fusion research center. Its stability has been demonstrated by tests in 2014 after 10 years of research and development activities, achieving 1μm stability @ 6m during one hour periods. MOTA is an Optical Ground Support Equipment aiming at qualifying by tests the Flexible Combined Imager (FCI). FCI is an instrument for the meteorological satellite MTG-I, a program of and funded by the European Space Agency and under prime contractorship of Thales Alenia Space. Optimized design will allow to get better than 0.2 μrad stability for one hour periods, as required for MTF measurement.

  10. AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT II, MAINTAINING THE AIR SYSTEM--DETROIT DIESEL ENGINES.

    ERIC Educational Resources Information Center

    Human Engineering Inst., Cleveland, OH.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF THE DIESEL ENGINE AIR SYSTEM. TOPICS ARE (1) OPERATION AND FUNCTION, (2) AIR CLEANER, (3) AIR SHUT-DOWN HOUSING, (4) EXHAUST SYSTEM, (5) BLOWER, (6) TURBOCHARGER, AND (7) TROUBLE-SHOOTING TIPS ON THE AIR SYSTEM. THE MODULE CONSISTS OF A…

  11. Program maintenance manual for nickel cadmium battery expert system, version 1

    NASA Technical Reports Server (NTRS)

    1986-01-01

    The Nickel-Cadmium Battery Expert System (NICBES) is an expert system for fault diagnosis and advice of the nickel-cadmium batteries found in the Hubble Space Telescope (HST). The system application and security, equipment environment, and the program maintenance procedures are examined.

  12. Preventative Maintenance.

    ERIC Educational Resources Information Center

    Migliorino, James

    Boards of education must be convinced that spending money up front for preventive maintenance will, in the long run, save districts' tax dollars. A good program of preventive maintenance can minimize disruption of service; reduce repair costs, energy consumption, and overtime; improve labor productivity and system equipment reliability; handle…

  13. Surface moisture measurement system operation and maintenance manual

    SciTech Connect

    Vargo, G.F., Westinghouse Hanford

    1996-06-11

    The purpose of this manual is to provide detailed operating instructions for the Surface Moisture Measurement System (SMMS).In addition, operating instructions for the Liquid Observation Well Moisture Measurement System (LOWMMS) are included. These systems were developed primarily in support of Tank Waste Remediation System (TWRS) Safety Programs for moisture measurement in organic and ferrocyanide watch list tanks.

  14. Optimal Parameter Design of Coarse Alignment for Fiber Optic Gyro Inertial Navigation System

    PubMed Central

    Lu, Baofeng; Wang, Qiuying; Yu, Chunmei; Gao, Wei

    2015-01-01

    Two different coarse alignment algorithms for Fiber Optic Gyro (FOG) Inertial Navigation System (INS) based on inertial reference frame are discussed in this paper. Both of them are based on gravity vector integration, therefore, the performance of these algorithms is determined by integration time. In previous works, integration time is selected by experience. In order to give a criterion for the selection process, and make the selection of the integration time more accurate, optimal parameter design of these algorithms for FOG INS is performed in this paper. The design process is accomplished based on the analysis of the error characteristics of these two coarse alignment algorithms. Moreover, this analysis and optimal parameter design allow us to make an adequate selection of the most accurate algorithm for FOG INS according to the actual operational conditions. The analysis and simulation results show that the parameter provided by this work is the optimal value, and indicate that in different operational conditions, the coarse alignment algorithms adopted for FOG INS are different in order to achieve better performance. Lastly, the experiment results validate the effectiveness of the proposed algorithm. PMID:26121614

  15. Optimal Parameter Design of Coarse Alignment for Fiber Optic Gyro Inertial Navigation System.

    PubMed

    Lu, Baofeng; Wang, Qiuying; Yu, Chunmei; Gao, Wei

    2015-01-01

    Two different coarse alignment algorithms for Fiber Optic Gyro (FOG) Inertial Navigation System (INS) based on inertial reference frame are discussed in this paper. Both of them are based on gravity vector integration, therefore, the performance of these algorithms is determined by integration time. In previous works, integration time is selected by experience. In order to give a criterion for the selection process, and make the selection of the integration time more accurate, optimal parameter design of these algorithms for FOG INS is performed in this paper. The design process is accomplished based on the analysis of the error characteristics of these two coarse alignment algorithms. Moreover, this analysis and optimal parameter design allow us to make an adequate selection of the most accurate algorithm for FOG INS according to the actual operational conditions. The analysis and simulation results show that the parameter provided by this work is the optimal value, and indicate that in different operational conditions, the coarse alignment algorithms adopted for FOG INS are different in order to achieve better performance. Lastly, the experiment results validate the effectiveness of the proposed algorithm. PMID:26121614

  16. Self maintenance robot system using physical information learning for mobile robot with visual sensors

    NASA Astrophysics Data System (ADS)

    Sekiguchi, Naohiro; Tanaka, Takayuki; Kaneko, Shun'ichi

    2005-12-01

    We propose self-maintenance robot system as a method which realizes work for a long time without maintenance by the human workers. This system absorbs the change which occurs in robot's hardware by learning, and maintains working ability. We propose the two methods of learning changes in the physical information of the robot as methods which realizes the maintenance-free robot system. One is a method to learn robot's physical information based on the input and output information in the task practice from the no physical information of the robot by using a neural network which has a task common layer and a task independence layer. We use a neural network which has a task common layer and a task independence layer to learning. Other is a method to learn robot's physical information based on the difference in hoping action and actual action. In this report, we verify of these learning system by the computer simulation.

  17. Precision Clean Hardware: Maintenance of Fluid Systems Cleanliness

    NASA Technical Reports Server (NTRS)

    Sharp, Sheila; Pedley, Mike; Bond, Tim; Quaglino, Joseph; Lorenz, Mary Jo; Bentz, Michael; Banta, Richard; Tolliver, Nancy; Golden, John; Levesque, Ray

    2003-01-01

    The ISS fluid systems are so complex that fluid system cleanliness cannot be verified at the assembly level. A "build clean / maintain clean" approach was used by all major fluid systems: Verify cleanliness at the detail and subassembly level. Maintain cleanliness during assembly.

  18. AUTOMOTIVE DIESEL MAINTENANCE 2. UNIT XX, TROUBLESHOOTING ELECTRICAL SYSTEMS.

    ERIC Educational Resources Information Center

    Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

    THIS MODULE OF A 25-MODULE COURSE IS DESIGNED TO ACQUAINT THE TRAINEE WITH TROUBLESHOOTING PROCEDURES FOR DIESEL ENGINE ELECTRICAL SYSTEMS. TOPICS ARE (1) TROUBLESHOOTING ELECTRICAL SYSTEMS (INTRODUCTION), (2) TOOLS AND INSTRUMENTS FOR TROUBLESHOOTING, (3) THE BATTERY, (4) PERIODIC BATTERY SERVICING, (5) THE DC CHARGING SYSTEM, (6) PERIODIC…

  19. Security Design of Remote Maintenance Systems for Nuclear Power Plants Based on ISO/IEC 15408

    NASA Astrophysics Data System (ADS)

    Watabe, Ryosuke; Oi, Tadashi; Endo, Yoshio

    This paper presents a security design of remote maintenance systems for nuclear power plants. Based on ISO/IEC 15408, we list assets to be protected, threats to the assets, security objectives against the threats, and security functional requirements that achieve the security objectives. Also, we show relations between the threats and the security objectives, and relations between the security objectives and the security functional requirements. As a result, we concretize a necessary and sufficient security design of remote maintenance systems for nuclear power plants that can protect the instrumentation and control system against intrusion, impersonation, tapping, obstruction and destruction.

  20. Development of an ion beam alignment system for real-time scanning tunneling microscope observation of dopant-ion irradiation

    SciTech Connect

    Kamioka, Takefumi; Sato, Kou; Kazama, Yutaka; Watanabe, Takanobu; Ohdomari, Iwao

    2008-07-15

    An ion beam alignment system has been developed in order to realize real-time scanning tunneling microscope (STM) observation of 'dopant-ion' irradiation that has been difficult due to the low emission intensity of the liquid-metal-ion-source (LMIS) containing dopant atoms. The alignment system is installed in our original ion gun and STM combined system (IG/STM) which is used for in situ STM observation during ion irradiation. By using an absorbed electron image unit and a dummy sample, ion beam alignment operation is drastically simplified and accurized. We demonstrate that sequential STM images during phosphorus-ion irradiation are successfully obtained for sample surfaces of Si(111)-7x7 at room temperature and a high temperature of 500 deg. C. The LMIS-IG/STM equipped with the developed ion beam alignment system would be a powerful tool for microscopic investigation of the dynamic processes of ion irradiation.

  1. The 747 primary flight control systems reliability and maintenance study

    NASA Technical Reports Server (NTRS)

    1979-01-01

    The major operational characteristics of the 747 Primary Flight Control Systems (PFCS) are described. Results of reliability analysis for separate control functions are presented. The analysis makes use of a NASA computer program which calculates reliability of redundant systems. Costs for maintaining the 747 PFCS in airline service are assessed. The reliabilities and cost will provide a baseline for use in trade studies of future flight control system design.

  2. New system enables fleets to tailor maintenance programs

    SciTech Connect

    Fiscor, S.

    2007-08-15

    The Lubrizol Corporation has developed FluiPak and FluiPak Lite systems to pull engine oils and sample them continuously, helping to maintain mining equipment between oil change intervals. The FluiPak system has a control box, a sensor box and a reserve system. FluiPak Lite is simply a cut-down version of FluiPak. The article explains how the system works to detect in real time oil quality and contaminants and hence optimize drain intervals and also prolong engine component life and reduce waste oil disposal costs. 100 units are currently installed in coal operations. 5 figs., 5 photos.

  3. 33 CFR 105.250 - Security systems and equipment maintenance.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... inspected, tested, calibrated, and maintained according to manufacturers' recommendations. (b) Security systems must be regularly tested in accordance with the manufacturers' recommendations; noted...

  4. Embedded expert system for space shuttle main engine maintenance

    NASA Technical Reports Server (NTRS)

    Pooley, J.; Thompson, W.; Homsley, T.; Teoh, W.; Jones, J.; Lewallen, P.

    1987-01-01

    The SPARTA Embedded Expert System (SEES) is an intelligent health monitoring system that directs analysis by placing confidence factors on possible engine status and then recommends a course of action to an engineer or engine controller. The technique can prevent catastropic failures or costly rocket engine down time because of false alarms. Further, the SEES has potential as an on-board flight monitor for reusable rocket engine systems. The SEES methodology synergistically integrates vibration analysis, pattern recognition and communications theory techniques with an artificial intelligence technique - the Embedded Expert System (EES).

  5. Digital Data Recording System (DDRS) operating and maintenance manual

    NASA Technical Reports Server (NTRS)

    Griffin, C. R.; Jones, J. I.

    1980-01-01

    The digital data recording system (DDRS) was designed, fabricated, tested, and delivered. This unit is the interface between the synthetic aperture radar (SAR) and the recording system. The SAR data are formatted in the DDRS for data processing on the ground.

  6. 78 FR 77574 - Protection System Maintenance Reliability Standard

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-12-24

    .... 824o (2012). \\2\\ Mandatory Reliability Standards for the Bulk Power System, Order No. 693, 72 FR 16,416... informational filing on the development of a guidance report concerning the commissioning of power system... reflect the known and reported condition or the historical performance of the relevant devices. 24....

  7. 14 CFR 129.113 - Fuel tank system maintenance program.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... based on fuel tank system Instructions for Continued Airworthiness (ICA) that have been developed in... service after any alteration for which fuel tank ICA are developed under SFAR 88, or under § 25.1529 in... for the airplane inspections and procedures for the fuel tank system based on those ICA. (f) The...

  8. 14 CFR 129.113 - Fuel tank system maintenance program.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... based on fuel tank system Instructions for Continued Airworthiness (ICA) that have been developed in... service after any alteration for which fuel tank ICA are developed under SFAR 88, or under § 25.1529 in... for the airplane inspections and procedures for the fuel tank system based on those ICA. (f) The...

  9. Learner-Centered Instruction (LCI): Volume 1-A. Systems Approach to Electronics Maintenance Training.

    ERIC Educational Resources Information Center

    Valverde, Horace H.

    The report describes the proposed development and evaluation of a learner-centered (LCI) systems approach to electronics maintenance training. An electronics course, appropriate for airmen of various aptitudes, will be prepared to develop proficiency in the specific duties required of a Weapon Control Systems Mechanic/Technician in the F-111A…

  10. 14 CFR 121.1111 - Electrical wiring interconnection systems (EWIS) maintenance program.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Electrical wiring interconnection systems (EWIS) maintenance program. 121.1111 Section 121.1111 Aeronautics and Space FEDERAL AVIATION... Airworthiness and Safety Improvements § 121.1111 Electrical wiring interconnection systems (EWIS)...

  11. 14 CFR 121.1111 - Electrical wiring interconnection systems (EWIS) maintenance program.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Electrical wiring interconnection systems (EWIS) maintenance program. 121.1111 Section 121.1111 Aeronautics and Space FEDERAL AVIATION... Airworthiness and Safety Improvements § 121.1111 Electrical wiring interconnection systems (EWIS)...

  12. 14 CFR 121.1111 - Electrical wiring interconnection systems (EWIS) maintenance program.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Electrical wiring interconnection systems (EWIS) maintenance program. 121.1111 Section 121.1111 Aeronautics and Space FEDERAL AVIATION... Airworthiness and Safety Improvements § 121.1111 Electrical wiring interconnection systems (EWIS)...

  13. An On-Line Data Management System for Repair and Maintenance of Computer Terminals.

    ERIC Educational Resources Information Center

    Muller, Mark T.

    This paper describes the design, installation, testing, and operation of a computer-based record keeping system for computer terminals and equipment. The system provides all levels of data management for maintenance with instantaneous reports on location of equipment, cost of equipment, cost of repairs, inventory and parts control, as well as a…

  14. AUTOMOTIVE DIESEL MAINTENANCE 2. UNIT X, AUTOMATIC TRANSMISSIONS--HYDRAULIC SYSTEMS (PART II).

    ERIC Educational Resources Information Center

    Human Engineering Inst., Cleveland, OH.

    THIS MODULE OF A 25-MODULE COURSE IS DESIGNED TO PROVIDE A SUMMARY OF MAINTENANCE PROCEDURES FOR AUTOMATIC TRANSMISSIONS USED ON DIESEL POWERED VEHICLES. TOPICS ARE (1) CHECKING THE HYDRAULIC SYSTEM, (2) SERVICING THE HYDRAULIC SYSTEM, (3) EXAMINING THE RANGE CONTROL VALVE, (4) EXAMINING THE LOCK-UP AND FLOW VALVE, (5) EXAMINING THE MAIN REGULATOR…

  15. Utilization and Maintenance of the Federal Catalog System (FCS)

    NASA Technical Reports Server (NTRS)

    1989-01-01

    The Federal Catalog System (FCS) was established and substantiated by law to aid the national economy and promote greater efficiency in supply management operations throughout the Federal Government. This Handbook establishes policies and procedures to be followed by NASA installations and certain contractors in cataloging items of supply in the Federal Catalog System and prescribes use of the system in supply management operations. This Handbook is not intended to duplicate the Federal Cataloging Manuals or Federal Cataloging Handbooks. For the most part, it describes actions that are peculiar to NASA.

  16. Synthesis of vertically aligned carbon nanofibers for interfacing with live systems

    SciTech Connect

    Melechko, Anatoli Vasilievich; Desikan, Ramya; McKnight, Timothy E; Klein, Kate L; Rack, P. D.

    2009-01-01

    The ability to synthesize carbon nanofibers with a high degree of control over their geometry, location, and structure via catalytic plasma-enhanced chemical vapor deposition has expanded the possibility of new applications. The nanoscale dimensions and high aspect ratio of vertically aligned carbon nanofibers (VACNFs), along with favorable physical and chemical characteristics, has provided a nanostructured material with properties that are well-suited for interfacing with live cells and tissues. This review surveys the aspects of synthesis, integration, and functionalization of VACNFs, followed by examples of how VACNFs have been used to interface with live systems for a variety of advanced nanoscale biological applications.

  17. Multisensor robotic system for autonomous space maintenance and repair

    NASA Technical Reports Server (NTRS)

    Abidi, M. A.; Green, W. L.; Chandra, T.; Spears, J.

    1988-01-01

    The feasibility of realistic autonomous space manipulation tasks using multisensory information is demonstrated. The system is capable of acquiring, integrating, and interpreting multisensory data to locate, mate, and demate a Fluid Interchange System (FIS) and a Module Interchange System (MIS). In both cases, autonomous location of a guiding light target, mating, and demating of the system are performed. Implemented visio-driven techniques are used to determine the arbitrary two-dimensional position and orientation of the mating elements as well as the arbitrary three-dimensional position and orientation of the light targets. A force/torque sensor continuously monitors the six components of force and torque exerted on the end-effector. Both FIS and MIS experiments were successfully accomplished on mock-ups built for this purpose. The method is immune to variations in the ambient light, in particular because of the 90-minute day-night shift in space.

  18. Knowledge-Based Systems (KBS) development standards: A maintenance perspective

    NASA Technical Reports Server (NTRS)

    Brill, John

    1990-01-01

    Information on knowledge-based systems (KBS) is given in viewgraph form. Information is given on KBS standardization needs, the knowledge engineering process, program management, software and hardware issues, and chronic problem areas.

  19. Multi-limbed locomotion systems for space construction and maintenance

    NASA Technical Reports Server (NTRS)

    Waldron, K. J.; Klein, C. A.

    1987-01-01

    A well developed technology of coordination of multi-limbed locomotory systems is now available. Results from a NASA sponsored study of several years ago are presented. This was a simulation study of a three-limbed locomotion/manipulation system. Each limb had six degrees of freedom and could be used either as a locomotory grasping hand-holds, or as a manipulator. The focus of the study was kinematic coordination algorithms. The presentation will also include very recent results from the Adaptive Suspension Vehicle Project. The Adaptive Suspension Vehicle (ASV) is a legged locomotion system designed for terrestrial use which is capable of operating in completely unstructured terrain in either a teleoperated or operator-on-board mode. Future development may include autonomous operation. The ASV features a very advanced coordination and control system which could readily be adapted to operation in space. An inertial package with a vertical gyro, and rate gyros and accelerometers on three orthogonal axes provides body position information at high bandwidth. This is compared to the operator's commands, injected via a joystick to provide a commanded force system on the vehicle's body. This system is, in turn, decomposed by a coordination algorithm into force commands to those legs which are in contact with the ground.

  20. An intelligent healthcare management system: a new approach in work-order prioritization for medical equipment maintenance requests.

    PubMed

    Hamdi, Naser; Oweis, Rami; Abu Zraiq, Hamzeh; Abu Sammour, Denis

    2012-04-01

    The effective maintenance management of medical technology influences the quality of care delivered and the profitability of healthcare facilities. Medical equipment maintenance in Jordan lacks an objective prioritization system; consequently, the system is not sensitive to the impact of equipment downtime on patient morbidity and mortality. The current work presents a novel software system (EQUIMEDCOMP) that is designed to achieve valuable improvements in the maintenance management of medical technology. This work-order prioritization model sorts medical maintenance requests by calculating a priority index for each request. Model performance was assessed by utilizing maintenance requests from several Jordanian hospitals. The system proved highly efficient in minimizing equipment downtime based on healthcare delivery capacity, and, consequently, patient outcome. Additionally, a preventive maintenance optimization module and an equipment quality control system are incorporated. The system is, therefore, expected to improve the reliability of medical equipment and significantly improve safety and cost-efficiency. PMID:20703695

  1. Use of the Abbe sine condition to quantify alignment aberrations in optical imaging systems

    NASA Astrophysics Data System (ADS)

    Burge, James H.; Zhao, Chunyu; Lu, Sheng Huei

    2010-08-01

    Violation of Abbe's sine condition is well-known to cause coma in axisymmetric imaging systems, and generally any offense against the sine condition (OSC) will cause aberrations that have linear dependence on the field angle. A well-corrected imaging system must obey the Abbe sine condition. A misaligned optical system can have particular forms of the OSC which are evaluated here. The lowest order non-trivial effects of misalignment have quadratic pupil dependence which causes a combination of astigmatism and focus that have linear field dependence. Higher order terms can arise from complex systems, but the effects of misalignment are nearly always dominated by the lowest order effects which can be fully characterized by measuring images on axis and the on-axis offense against the sine condition. By understanding the form of the on-axis images and the OSC, the state of alignment can be determined.

  2. Automated sample mounting and technical advance alignment system for biological crystallography at a synchrotron source

    SciTech Connect

    Snell, Gyorgy; Cork, Carl; Nordmeyer, Robert; Cornell, Earl; Meigs, George; Yegian, Derek; Jaklevic, Joseph; Jin, Jian; Stevens, Raymond C.; Earnest, Thomas

    2004-01-07

    High-throughput data collection for macromolecular crystallography requires an automated sample mounting system for cryo-protected crystals that functions reliably when integrated into protein-crystallography beamlines at synchrotrons. Rapid mounting and dismounting of the samples increases the efficiency of the crystal screening and data collection processes, where many crystals can be tested for the quality of diffraction. The sample-mounting subsystem has random access to 112 samples, stored under liquid nitrogen. Results of extensive tests regarding the performance and reliability of the system are presented. To further increase throughput, we have also developed a sample transport/storage system based on ''puck-shaped'' cassettes, which can hold sixteen samples each. Seven cassettes fit into a standard dry shipping Dewar. The capabilities of a robotic crystal mounting and alignment system with instrumentation control software and a relational database allows for automated screening and data collection to be developed.

  3. An Advanced Tool for Control System Design and Maintenance

    SciTech Connect

    Storm, Joachim; Lohmann, Heinz

    2006-07-01

    The detailed engineering for control systems is usually supported by CAD Tools creating the relevant logic diagrams including software parameters and signal cross references. However at this stage of the design an early V and V process for checking out the functional correctness of the design is not available. The article describes the scope and capabilities of an advanced control system design tool which has the embedded capability of a stand-alone simulation of complex logic structures. The tool provides the following features for constructing logic diagrams for control systems: - Drag and Drop construction of logic diagrams using a predefined symbol sets; - Cross reference facility; - Data extraction facility; - Stand-alone simulation for Logic Diagrams featuring: On the fly changes, signal line animation, value boxes and mini trends etc. - Creation and on-line animation of Compound Objects (Handler); - Code Generation Facility for Simulation; - Code Generation Facility for several control systems. The results of the integrated simulation based V and V process can be used further for initial control system configuration and life cycle management as well as for Engineering Test Bed applications and finally in full Scope Replica Simulators for Operator Training. (authors)

  4. Neogene-Quaternary Volcanic Alignments in the Transantarctic Mountains and West Antarctic Rift System of Southern Victoria Land, Antarctica

    NASA Astrophysics Data System (ADS)

    Paulsen, T. S.; Wilson, T. J.

    2004-12-01

    Neogene-Quaternary volcanism in southern Victoria Land, Antarctica, produced the Erebus Volcanic Province, a suite of alkaline volcanic rocks that extend from the Transantarctic Mountains rift-flank uplift to offshore localities within the West Antarctic rift system. We are mapping volcanic vent patterns in the province to detect alignments indicative of stress/strain patterns during rift evolution. In the southern sector of the Erebus Volcanic Province in the Royal Society Range Block of the Transantarctic Mountains, mapping shows that elliptical scoria cones, fissures, dikes, and linear vent arrays define volcanic alignments that have a dominant NNE trend, with subsidiary WNW trends. Age data for the alignments suggest that this pattern persisted from 14.6 to 0.25 Ma. We are currently completing mapping along an east-west transect crossing the rift margin, and results obtained so far within the rift region indicate a similar pattern of alignments. On the northern flank of Mount Morning, a large volcano just to the east of the Royal Society Range, elliptical scoria cones and linear vent arrays define volcanic alignments that have a dominant NE trend, with a subsidiary NNW trend. Available age data suggest that many of these cone alignments may be of Quaternary age. At Brown Peninsula, further east from the rift flank, cone alignments trend NNE and available ages range from 2 to 3 Ma. To the east of Brown Peninsula, cone alignments trend NW at Black Island, but are of uncertain age; age data on Black Island range from 11 to 3.4 Ma. At White Island, the farthest east into the rift, cone alignments trend NNE and available age data suggest volcanism as young as 0.2 Ma. Although some differences in cone alignment trends are apparent between the rift flank and the rift system across our transect, both regions appear to be dominated by NE trending alignments, which implies a WNW to NW minimum horizontal stress (Shmin) direction. This is oblique to the ENE Shmin Cape

  5. Integrating Safety in the Aviation System: Interdepartmental Training for Pilots and Maintenance Technicians

    NASA Technical Reports Server (NTRS)

    Mattson, Marifran; Petrin, Donald A.; Young, John P.

    2001-01-01

    The study of human factors has had a decisive impact on the aviation industry. However, the entire aviation system often is not considered in researching, training, and evaluating human factors issues especially with regard to safety. In both conceptual and practical terms, we argue for the proactive management of human error from both an individual and organizational systems perspective. The results of a multidisciplinary research project incorporating survey data from professional pilots and maintenance technicians and an exploratory study integrating students from relevant disciplines are reported. Survey findings suggest that latent safety errors may occur during the maintenance discrepancy reporting process because pilots and maintenance technicians do not effectively interact with one another. The importance of interdepartmental or cross-disciplinary training for decreasing these errors and increasing safety is discussed as a primary implication.

  6. 78 FR 44475 - Protection System Maintenance Reliability Standard

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-07-24

    ... Standards for the Bulk Power System, Order No. 693, 72 FR 16,416 (April 4, 2007), FERC Stats. & Regs. ] 31... process of a battery cell make establishment of a designated segment based on manufacturer and type of..., DC 20426 [Attention: Ellen Brown, email: DataClearance@ferc.gov , phone: (202) 502-8663, fax:...

  7. Monitoring and Maintenance of the German Indonesian Tsunami Early Warning System (GITEWS)

    NASA Astrophysics Data System (ADS)

    Gensch, S.; Günther, M.; Henneberger, R.

    2012-04-01

    This article discusses aspects of and experiences with monitoring and maintenance of the geographically widely distributed components of a Tsunami Early Warning System (TEWS) in the Indian Ocean. Many of the issues, encountered during work within the GITEWS project (German Indonesian Tsunami Early Warning System, Rudloff et al., 2009) on the design and implementation of the monitoring system, are also relevant for other types of warning systems. With this article, insights and lessons learned are shared with the community. Failure to deliver a warning has fatal consequences. Based on an analysis of the criticalness, vulnerability and availability of single components, we describe the design and implementation of a communication and monitoring architecture and development of standard operating procedures (SOP) for maintenance (Communication architecture of an early warning system, Angermann et al., 2010). The GITEWS project is composed of several thousand integrated system components and software processes. During the establishment of the currently existing system, complexity grew and monitoring and maintenance needed further automation to capture any critical states of the whole system and to establish the correct responsive means. One means of monitoring is the use of an adapted Nagios monitoring implementation covering a large number of infrastructure assets (hosts, network components, remote sensor stations, storage) and business processes (processes and applications). This is to be extended in the future for further operational monitoring of station parameters (power voltage, battery levels) with the challenge of monitoring in on- and offline modes. An aspect of maintenance is the development of a practical and precise means of documenting all system properties. Providing a platform for continuous documentation of system changes and maintenance and enabling information-exchange/ collaboration between the different responsible institutions, departments and

  8. Remotely operated welding systems for EdF plant maintenance

    SciTech Connect

    Thapon, G. ); Blight, J.; Durand, B. )

    1992-01-01

    With the objective of improving weld quality, reducing outage times, and minimizing integrated dose, Electricite de France (EdF) and Comex Nucleaire (CxN) have developed a number of advanced remotely controlled welding systems. Three such developments are described, two having been used operationally and the third being qualified for use in the coming months. The three developments involve replacing pressurizes heaters, replacing fuel charge head sleeves, and real-time interactive welding.

  9. Standard Hydrogen Monitoring System-C operation and maintenance manual

    SciTech Connect

    Schneider, T.C.

    1997-05-01

    The primary function of the SHMS-C is to monitor specifically for hydrogen in the waste tank vapor space which may also contain (but not be limited to) unknown quantities of air, nitrous oxide (N{sub 2}O), ammonia (NH{sub 3}), water vapor, carbon dioxide (CO{sub 2}), carbon monoxide (CO) and other gaseous constituents. An electronically controlled grab sampler has replaced the manually operated sample system that was used in the original SHMS enclosure. Samples can now be operator or automatically initiated. Automatic initiation occurs based on the high hydrogen alarm level. Once a sample is obtained it is removed from the sampler and transported to a laboratory for analysis. This system is used to identify other gaseous constituents which are not measured by the hydrogen monitor. The design does not include any remote data acquisition or remote data logging equipment but provides a 4--20 mA dc process signals, and discrete alarm contacts, that can be utilized for remote data logging and alarming when desired. The SHMS-C arrangement consists of design modifications (piping, valves, filters, supports) to the SHMS-B arrangement necessary for the installation of a dual column gas chromatograph and associated sample and calibration gas lines. The gas chromatograph will provide real time, analytical quality, specific hydrogen measurements in low and medium range concentrations. The system is designed to sample process gases that are classified by NEC code as Class 1, Division 1, Group B.

  10. Starspots and Spin-orbit Alignment in the WASP-4 Exoplanetary System

    NASA Astrophysics Data System (ADS)

    Sanchis-Ojeda, Roberto; Winn, Joshua N.; Holman, Matthew J.; Carter, Joshua A.; Osip, David J.; Fuentes, Cesar I.

    2011-06-01

    We present photometry of four transits of the exoplanet WASP-4b, each with a precision of approximately 500 ppm and a time sampling of 40-60 s. We have used the data to refine the estimates of the system parameters and ephemerides. During two of the transits we observed a short-lived, low-amplitude anomaly that we interpret as the occultation of a starspot by the planet. We also found evidence for a pair of similar anomalies in previously published photometry. The recurrence of these anomalies suggests that the stellar rotation axis is nearly aligned with the orbital axis, or else the starspot would not have remained on the transit chord. By analyzing the timings of the anomalies we find the sky-projected stellar obliquity to be λ = -1+14 - 12 degrees. This result is consistent with (and more constraining than) a recent observation of the Rossiter-McLaughlin effect. It suggests that the planet migration mechanism preserved the initially low obliquity, or else that tidal evolution has realigned the system. Future applications of this method using data from the CoRoT and Kepler missions will allow spin-orbit alignment to be probed for many other exoplanets. Based on observations with the 6.5 m Magellan Telescopes located at Las Campanas Observatory, Chile.

  11. Hall station and camera system operation and maintenance manual

    NASA Technical Reports Server (NTRS)

    Piekutowski, A. J.; Strader, E. A.

    1986-01-01

    The major components of the Hall station and camera system are described. The Hall film record of an event provides the time of flight of the projectile between the slits. A time mark generator is used to supply extremely short pulses of light at a known frequency. These pulses of light are used to produce timing marks on the edge of the film. Comparison of these marks with the spacing of the projectile images provides the information necessary to determine the time of flight of the projectile. Since the slits are installed with a known separation distance, calculation of the velocity of any object passing both slits is a simple matter.

  12. Maintenance and Logistics Support for the International Monitoring System Network of the CTBTO

    NASA Astrophysics Data System (ADS)

    Haslinger, F.; Brely, N.; Akrawy, M.

    2007-05-01

    The global network of the International Monitoring System (IMS) of the Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO), once completed, will consist of 321 monitoring facilities of four different technologies: hydroacoustic, seismic, infrasonic, and radionuclide. As of today, about 65% of the installations are completed and contribute data to the products issued by the International Data Centre (IDC) of the CTBTO. In order to accomplish the task to reliably collect evidence for any potential nuclear test explosion anywhere on the planet, all stations are required to perform to very high data availability requirements (at least 98% data availability over a 12-month period). To enable reaching this requirement, a three-layer concept has been developed to allow efficient support of the IMS stations: Operations, Maintenance and Logistics, and Engineering. Within this concept Maintenance and Logistics provide second level support of the stations, whereby problems arising at the station are assigned through the IMS ticket system to Maintenance if they cannot be resolved on the Operations level. Maintenance will then activate the required resources to appropriately address and ultimately resolve the problem. These resources may be equipment support contracts, other third party contracts, or the dispatch of a maintenance team. Engineering Support will be activated if the problem requires redesign of the station or after catastrophic failures when a total rebuild of a station may be necessary. In this model, Logistics Support is responsible for parts replenishment and support contract management. Logistics Support also collects and analyzes relevant failure mode and effect information, develops supportability models, and has the responsibility for document management, obsolescence, risk & quality, and configuration management, which are key elements for efficient station support. Maintenance Support in addition is responsible for maintenance strategies, for

  13. CERN experience and strategy for the maintenance of cryogenic plants and distribution systems

    NASA Astrophysics Data System (ADS)

    Serio, L.; Bremer, J.; Claudet, S.; Delikaris, D.; Ferlin, G.; Pezzetti, M.; Pirotte, O.; Tavian, L.; Wagner, U.

    2015-12-01

    CERN operates and maintains the world largest cryogenic infrastructure ranging from ageing installations feeding detectors, test facilities and general services, to the state-of-the-art cryogenic system serving the flagship LHC machine complex. After several years of exploitation of a wide range of cryogenic installations and in particular following the last two years major shutdown to maintain and consolidate the LHC machine, we have analysed and reviewed the maintenance activities to implement an efficient and reliable exploitation of the installations. We report the results, statistics and lessons learned on the maintenance activities performed and in particular the required consolidations and major overhauling, the organization, management and methodologies implemented.

  14. Electrical Procedures and Environmental Control Systems. Building Maintenance. Module IV. Instructor's Guide.

    ERIC Educational Resources Information Center

    Sloan, Garry

    This curriculum guide, one of six modules keyed to the building maintenance competency profile developed by industry and education professionals, provides materials for two units on electrical procedures and environmental control systems. Unit 1, on electrical procedures, includes the following lessons: electrical safety; troubleshooting and…

  15. Methods to Use Surface Infiltration Tests in Permeable Pavement Systems to Determine Maintenance Frequency

    EPA Science Inventory

    Currently, there is limited guidance on selecting test sites to measure surface infiltration rates in permeable pavement systems to determine maintenance frequency. The ASTM method (ASTM C1701) for measuring infiltration rate of in-place pervious concrete suggest to either (1) p...

  16. 76 FR 7102 - Simplified Network Application Processing System, On-line Registration and Account Maintenance

    Federal Register 2010, 2011, 2012, 2013, 2014

    2011-02-09

    ... Bureau of Industry and Security 15 CFR Part 748 RIN 0694-AE98 Simplified Network Application Processing System, On-line Registration and Account Maintenance AGENCY: Bureau of Industry and Security, Commerce. ACTION: Final rule. SUMMARY: The Bureau of Industry and Security (BIS) amends the Export...

  17. 49 CFR 180.416 - Discharge system inspection and maintenance program for cargo tanks transporting liquefied...

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Discharge system inspection and maintenance program for cargo tanks transporting liquefied compressed gases. 180.416 Section 180.416 Transportation... program for cargo tanks transporting liquefied compressed gases. (a) Applicability. This section...

  18. 14 CFR 129.111 - Electrical wiring interconnection systems (EWIS) maintenance program.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Electrical wiring interconnection systems (EWIS) maintenance program. 129.111 Section 129.111 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIR CARRIERS AND OPERATORS FOR COMPENSATION OR HIRE: CERTIFICATION AND OPERATIONS OPERATIONS:...

  19. Occupational Analysis Technology: Expanded Role in Development of Cost-Effective Maintenance Systems. Final Report.

    ERIC Educational Resources Information Center

    Foley, John P., Jr.

    A study was conducted to refine and coordinate occupational analysis, job performance aids, and elements of the instructional systems development process for task specific Air Force maintenance training. Techniques for task identification and analysis (TI & A) and data gathering techniques for occupational analysis were related. While TI & A and…

  20. 14 CFR 1212.601 - Maintenance and publication requirements for systems of records.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 14 Aeronautics and Space 5 2012-01-01 2012-01-01 false Maintenance and publication requirements for systems of records. 1212.601 Section 1212.601 Aeronautics and Space NATIONAL AERONAUTICS AND SPACE... accomplish a purpose or to carry out a function of NASA authorized by law or by Executive order of...

  1. The maintenance of a mixed mating system in the rocky mountain columbine: is it adaptive

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Mixed mating system, where both selfing and outcrossing occur in a population, is a common feature of the rocky mountain columbine, Aquilegia coerulea, where outcrossing rates vary between 0.41 and 0.93 among populations. We examined whether the maintenance of selfing in these populations is adaptiv...

  2. 30 CFR 250.1611 - Blowout preventer systems tests, actuations, inspections, and maintenance.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 2 2012-07-01 2012-07-01 false Blowout preventer systems tests, actuations, inspections, and maintenance. 250.1611 Section 250.1611 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations...

  3. CHARACTERIZATION OF OPERATING AND MAINTENANCE PRACTICES FOR WASTEWATER TREATMENT SYSTEMS IN THE IRON AND STEEL INDUSTRY

    EPA Science Inventory

    The report documents effective operating and maintenance (O/M) practices for wastewater treatment systems in the iron and steel industry, and describes how their application might affect permit parameters and operational upsets. Selection of processes for the study--byproduct cok...

  4. Building an Apprenticeship and Training System for Maintenance Occupations in the American Transit Industry

    ERIC Educational Resources Information Center

    Glover, Robert W.; Clopton, Lewis; McCollum, Malcolm; Wang, Xinge

    2007-01-01

    Purpose: The purpose of this paper is to discuss the joint training and apprenticeship system emerging in maintenance occupations in the US transit industry, its challenges and strategies to overcome them. Design/methodology/approach: The paper reports on early results, including efforts to develop a consensus national framework for apprenticeship…

  5. Maintenance History of an Oberlin{reg_sign} Pressure Filter System

    SciTech Connect

    Burch, J.V.; Norford, S.W.; Martin, H.L.

    1998-05-01

    Two Oberlin 24 sq. ft. pressure filters, operating in parallel for thirteen years at the Savannah River Site, have reliably removed precipitated metals from treated wastewater for direct discharge to surface stream. The maintenance history and modifications of these filters, as well as their flocculation and filter aid addition systems are reviewed. These system modifications have successfully extended service life of individual components and have improved total systems performance.

  6. Selection of a handling and maintenance option for the SP-100 ground engineering system test

    NASA Astrophysics Data System (ADS)

    Shen, E. J.; Schweiger, L. J.; Miller, W. C.; Gluck, R.; Davies, S. M.

    In the fall of 1990, a flight prototypic SP-100 reactor, control system, and flight shield will be tested in a simulated space environment. The reactor, shield and primary liquid metal heat transport system form the module known as the Test Article (TA) which will be tested. A discussion is presented on the development of a TA Handling System which will support the installation, maintenance, and disassembly of the TA.

  7. Railplug Ignition System for Enhanced Engine Performance and Reduced Maintenance

    SciTech Connect

    DK Ezekoye; Matt Hall; Ron Matthews

    2005-08-01

    This Final Technical Report discusses the progress that was made on the experimental and numerical tasks over the duration of this project. The primary objectives of the project were to (1) develop an improved understanding of the spark ignition process, and (2) develop the railplug as an improved ignitor for large bore stationary natural gas engines. We performed fundamental experiments on the physical processes occurring during spark ignition and used the results from these experiments to aid our development of the most complete model of the spark ignition process ever devised. The elements in this model include (1) the dynamic response of the ignition circuit, (2) a chemical kinetics mechanism that is suitable for the reactions that occur in the plasma, (3) conventional flame propagation kinetics, and (4) a multi-dimensional formulation so that bulk flow through the spark gap can be incorporated. This model (i.e., a Fortran code that can be used as a subroutine within an engine modeling code such as KIVA) can be obtained from Prof. Ron Matthews at rdmatt{at}mail.utexas.edu or Prof. DK Ezekoye at dezekoye{at}mail.utexas.edu. Fundamental experiments, engine experiments, and modeling tasks were used to help develop the railplug as a new ignitor for large bore natural gas engines. As the result of these studies, we developed a railplug that could extend the Lean Stability Limit (LSL) of an engine operating at full load on natural gas from {phi} = 0.59 for operation on spark plugs down to {phi} = 0.53 using railplugs with the same delivered energy (0.7 J). However, this delivered energy would rapidly wear out the spark plug. For a conventional delivered energy (<0.05 J), the LSL is {phi} = 0.63 for a spark plug. Further, using a permanent magnet to aid the plasma movement, the LSL was extended to {phi} = 0.54 for a railplug with a delivered energy of only 0.15 J/shot, a typical discharge energy for commercial capacitive discharge ignition systems. Here, it should be

  8. Software for Alignment of Segments of a Telescope Mirror

    NASA Technical Reports Server (NTRS)

    Hall, Drew P.; Howard, Richard T.; Ly, William C.; Rakoczy, John M.; Weir, John M.

    2006-01-01

    The Segment Alignment Maintenance System (SAMS) software is designed to maintain the overall focus and figure of the large segmented primary mirror of the Hobby-Eberly Telescope. This software reads measurements made by sensors attached to the segments of the primary mirror and from these measurements computes optimal control values to send to actuators that move the mirror segments.

  9. Health Maintenance System (HMS) Hardware Research, Design, and Collaboration

    NASA Technical Reports Server (NTRS)

    Gonzalez, Stefanie M.

    2010-01-01

    The Space Life Sciences division (SLSD) concentrates on optimizing a crew member's health. Developments are translated into innovative engineering solutions, research growth, and community awareness. This internship incorporates all those areas by targeting various projects. The main project focuses on integrating clinical and biomedical engineering principles to design, develop, and test new medical kits scheduled for launch in the Spring of 2011. Additionally, items will be tagged with Radio Frequency Interference Devices (RFID) to keep track of the inventory. The tags will then be tested to optimize Radio Frequency feed and feed placement. Research growth will occur with ground based experiments designed to measure calcium encrusted deposits in the International Space Station (ISS). The tests will assess the urine calcium levels with Portable Clinical Blood Analyzer (PCBA) technology. If effective then a model for urine calcium will be developed and expanded to microgravity environments. To support collaboration amongst the subdivisions of SLSD the architecture of the Crew Healthcare Systems (CHeCS) SharePoint site has been redesigned for maximum efficiency. Community collaboration has also been established with the University of Southern California, Dept. of Aeronautical Engineering and the Food and Drug Administration (FDA). Hardware disbursements will transpire within these communities to support planetary surface exploration and to serve as an educational tool demonstrating how ground based medicine influenced the technological development of space hardware.

  10. Starspots And Spin-orbit Alignment In the Wasp-4 Exoplanetary System

    NASA Astrophysics Data System (ADS)

    Sanchis Ojeda, Roberto; Winn, J. N.; Holman, M. J.; Carter, J. A.; Osip, D. J.; Fuentes, C. I.

    2011-05-01

    We present photometry of 4 transits of the exoplanet WASP-4b, each with a precision of approximately 500 ppm and a time sampling of 40-60s. During two of the transits we observed a short-lived, low-amplitude anomaly that we interpret as the occultation of a starspot by the planet. We also find evidence for a pair of similar anomalies in previously published photometry. The recurrence of these anomalies suggests that the stellar rotation axis is nearly aligned with the orbital axis, or else the star spot would not have remained on the transit chord. By analyzing the timings of the anomalies we find the sky-projected stellar obliquity to be 1^{+12}_{-14} degrees. This result is consistent with (and more constraining than) a recent observation of the Rossiter-McLaughlin effect. It suggests that the planet migration mechanism preserved the initially low obliquity, or else that tidal evolution has realigned the system. We discuss future applications of this method using data from the Kepler satellite, which will allow spin-orbit alignment to be probed for many other exoplanets.

  11. Environmental constraints shaping constituent order in emerging communication systems: Structural iconicity, interactive alignment and conventionalization.

    PubMed

    Christensen, Peer; Fusaroli, Riccardo; Tylén, Kristian

    2016-01-01

    Where does linguistic structure come from? Recent gesture elicitation studies have indicated that constituent order (corresponding to for instance subject-verb-object, or SVO in English) may be heavily influenced by human cognitive biases constraining gesture production and transmission. Here we explore the alternative hypothesis that syntactic patterns are motivated by multiple environmental and social-interactional constraints that are external to the cognitive domain. In three experiments, we systematically investigate different motivations for structure in the gestural communication of simple transitive events. The first experiment indicates that, if participants communicate about different types of events, manipulation events (e.g. someone throwing a cake) and construction events (e.g. someone baking a cake), they spontaneously and systematically produce different constituent orders, SOV and SVO respectively, thus following the principle of structural iconicity. The second experiment shows that participants' choice of constituent order is also reliably influenced by social-interactional forces of interactive alignment, that is, the tendency to re-use an interlocutor's previous choice of constituent order, thus potentially overriding affordances for iconicity. Lastly, the third experiment finds that the relative frequency distribution of referent event types motivates the stabilization and conventionalization of a single constituent order for the communication of different types of events. Together, our results demonstrate that constituent order in emerging gestural communication systems is shaped and stabilized in response to multiple external environmental and social factors: structural iconicity, interactive alignment and distributional frequency. PMID:26402649

  12. Method to determine and adjust the alignment of the transmitter and receiver fields of view of a LIDAR system

    DOEpatents

    Schmitt, Randal L.; Henson, Tammy D.; Krumel, Leslie J.; Hargis, Jr., Philip J.

    2006-06-20

    A method to determine the alignment of the transmitter and receiver fields of view of a light detection and ranging (LIDAR) system. This method can be employed to determine the far-field intensity distribution of the transmitter beam, as well as the variations in transmitted laser beam pointing as a function of time, temperature, or other environmental variables that may affect the co-alignment of the LIDAR system components. In order to achieve proper alignment of the transmitter and receiver optical systems when a LIDAR system is being used in the field, this method employs a laser-beam-position-sensing detector as an integral part of the receiver optics of the LIDAR system.

  13. Terminator field-aligned current system: A new finding from model-assimilated data set (MADS)

    NASA Astrophysics Data System (ADS)

    Zhu, L.; Schunk, R. W.; Scherliess, L.; Sojka, J. J.; Gardner, L. C.; Eccles, J. V.; Rice, D.

    2013-12-01

    Physics-based data assimilation models have been recognized by the space science community as the most accurate approach to specify and forecast the space weather of the solar-terrestrial environment. The model-assimilated data sets (MADS) produced by these models constitute an internally consistent time series of global three-dimensional fields whose accuracy can be estimated. Because of its internal consistency of physics and completeness of descriptions on the status of global systems, the MADS has also been a powerful tool to identify the systematic errors in measurements, reveal the missing physics in physical models, and discover the important dynamical physical processes that are inadequately observed or missed by measurements due to observational limitations. In the past years, we developed a data assimilation model for the high-latitude ionospheric plasma dynamics and electrodynamics. With a set of physical models, an ensemble Kalman filter, and the ingestion of data from multiple observations, the data assimilation model can produce a self-consistent time-series of the complete descriptions of the global high-latitude ionosphere, which includes the convection electric field, horizontal and field-aligned currents, conductivity, as well as 3-D plasma densities and temperatures, In this presentation, we will show a new field-aligned current system discovered from the analysis of the MADS produced by our data assimilation model. This new current system appears and develops near the ionospheric terminator. The dynamical features of this current system will be described and its connection to the active role of the ionosphere in the M-I coupling will be discussed.

  14. Spin-Orbit Alignment of Exoplanet Systems: Ensemble Analysis Using Asteroseismology

    NASA Astrophysics Data System (ADS)

    Campante, T. L.; Lund, M. N.; Kuszlewicz, J. S.; Davies, G. R.; Chaplin, W. J.; Albrecht, S.; Winn, J. N.; Bedding, T. R.; Benomar, O.; Bossini, D.; Handberg, R.; Santos, A. R. G.; Van Eylen, V.; Basu, S.; Christensen-Dalsgaard, J.; Elsworth, Y. P.; Hekker, S.; Hirano, T.; Huber, D.; Karoff, C.; Kjeldsen, H.; Lundkvist, M. S.; North, T. S. H.; Silva Aguirre, V.; Stello, D.; White, T. R.

    2016-03-01

    The angle ψ between a planet’s orbital axis and the spin axis of its parent star is an important diagnostic of planet formation, migration, and tidal evolution. We seek empirical constraints on ψ by measuring the stellar inclination is via asteroseismology for an ensemble of 25 solar-type hosts observed with NASA’s Kepler satellite. Our results for is are consistent with alignment at the 2σ level for all stars in the sample, meaning that the system surrounding the red-giant star Kepler-56 remains as the only unambiguous misaligned multiple-planet system detected to date. The availability of a measurement of the projected spin-orbit angle λ for two of the systems allows us to estimate ψ. We find that the orbit of the hot Jupiter HAT-P-7b is likely to be retrograde (\\psi =116\\buildrel{\\circ}\\over{.} {4}-14.7+30.2), whereas that of Kepler-25c seems to be well aligned with the stellar spin axis (\\psi =12\\buildrel{\\circ}\\over{.} {6}-11.0+6.7). While the latter result is in apparent contradiction with a statement made previously in the literature that the multi-transiting system Kepler-25 is misaligned, we show that the results are consistent, given the large associated uncertainties. Finally, we perform a hierarchical Bayesian analysis based on the asteroseismic sample in order to recover the underlying distribution of ψ. The ensemble analysis suggests that the directions of the stellar spin and planetary orbital axes are correlated, as conveyed by a tendency of the host stars to display large values of inclination.

  15. Genetic algorithm based fast alignment method for strap-down inertial navigation system with large azimuth misalignment.

    PubMed

    He, Hongyang; Xu, Jiangning; Qin, Fangjun; Li, Feng

    2015-11-01

    In order to shorten the alignment time and eliminate the small initial misalignment limit for compass alignment of strap-down inertial navigation system (SINS), which is sometimes not easy to satisfy when the ship is moored or anchored, an optimal model based time-varying parameter compass alignment algorithm is proposed in this paper. The contributions of the work presented here are twofold. First, the optimization of compass alignment parameters, which involves a lot of trial-and-error traditionally, is achieved based on genetic algorithm. On this basis, second, the optimal parameter varying model is established by least-square polynomial fitting. Experiments are performed with a navigational grade fiber optical gyroscope SINS, which validate the efficiency of the proposed method. PMID:26628165

  16. Genetic algorithm based fast alignment method for strap-down inertial navigation system with large azimuth misalignment

    NASA Astrophysics Data System (ADS)

    He, Hongyang; Xu, Jiangning; Qin, Fangjun; Li, Feng

    2015-11-01

    In order to shorten the alignment time and eliminate the small initial misalignment limit for compass alignment of strap-down inertial navigation system (SINS), which is sometimes not easy to satisfy when the ship is moored or anchored, an optimal model based time-varying parameter compass alignment algorithm is proposed in this paper. The contributions of the work presented here are twofold. First, the optimization of compass alignment parameters, which involves a lot of trial-and-error traditionally, is achieved based on genetic algorithm. On this basis, second, the optimal parameter varying model is established by least-square polynomial fitting. Experiments are performed with a navigational grade fiber optical gyroscope SINS, which validate the efficiency of the proposed method.

  17. Neural-network-directed alignment of optical systems using the laser-beam spatial filter as an example

    NASA Technical Reports Server (NTRS)

    Decker, Arthur J.; Krasowski, Michael J.; Weiland, Kenneth E.

    1993-01-01

    This report describes an effort at NASA Lewis Research Center to use artificial neural networks to automate the alignment and control of optical measurement systems. Specifically, it addresses the use of commercially available neural network software and hardware to direct alignments of the common laser-beam-smoothing spatial filter. The report presents a general approach for designing alignment records and combining these into training sets to teach optical alignment functions to neural networks and discusses the use of these training sets to train several types of neural networks. Neural network configurations used include the adaptive resonance network, the back-propagation-trained network, and the counter-propagation network. This work shows that neural networks can be used to produce robust sequencers. These sequencers can learn by example to execute the step-by-step procedures of optical alignment and also can learn adaptively to correct for environmentally induced misalignment. The long-range objective is to use neural networks to automate the alignment and operation of optical measurement systems in remote, harsh, or dangerous aerospace environments. This work also shows that when neural networks are trained by a human operator, training sets should be recorded, training should be executed, and testing should be done in a manner that does not depend on intellectual judgments of the human operator.

  18. ANALYSIS OF SPIN-ORBIT ALIGNMENT IN THE WASP-32, WASP-38, AND HAT-P-27/WASP-40 SYSTEMS

    SciTech Connect

    Brown, D. J. A.; Collier Cameron, A.; Enoch, B.; Miller, G. R. M.; Diaz, R. F.; Doyle, A. P.; Smalley, B.; Anderson, D. R.; Hellier, C.; Maxted, P. F. L.; Gillon, M.; Lendl, M.; Triaud, A. H. M. J.; Queloz, D.; Pollacco, D.; Boisse, I.; Hebrard, G.

    2012-12-01

    We present measurements of the spin-orbit alignment angle, {lambda}, for the hot Jupiter systems WASP-32, WASP-38, and HAT-P-27/WASP-40, based on data obtained using the HARPS spectrograph. We analyze the Rossiter-McLaughlin effect for all three systems and also carry out Doppler tomography for WASP-32 and WASP-38. We find that WASP-32 (T {sub eff} = 6140{sup +90} {sub -100} K) is aligned, with an alignment angle of {lambda} = 10.{sup 0}5{sup +6.4} {sub -6.5} obtained through tomography, and that WASP-38 (T {sub eff} = 6180{sup +40} {sub -60} K) is also aligned, with tomographic analysis yielding {lambda} = 7.{sup 0}5{sup +4.7} {sub -6.1}. The latter result provides an order-of-magnitude improvement in the uncertainty in {lambda} compared to the previous analysis of Simpson et al. We are only able to loosely constrain the angle for HAT-P-27/WASP-40 (T{sub eff} = 5190{sup +160} {sub -170} K) to {lambda} = 24.{sup 0}2{sup +76.0}{sub -44.5}, owing to the poor signal-to-noise ratio of our data. We consider this result a non-detection under a slightly updated version of the alignment test of Brown et al. We place our results in the context of the full sample of spin-orbit alignment measurements, finding that they provide further support for previously established trends.

  19. Inspection, maintenance, and repair of large pumps and piping systems using advanced robotic tools

    SciTech Connect

    Lewis, R.K.; Radigan, T.M.

    1998-07-01

    Operating and maintaining large pumps and piping systems can be an expensive proposition. Proper inspections and monitoring can reduce costs. This was difficult in the past, since detailed pump inspections could only be performed by disassembly and many portions of piping systems are buried or covered with insulation. Once these components were disassembled, a majority of the cost was already incurred. At that point, expensive part replacement usually took place whether it was needed or not. With the completion of the Pipe Walker{trademark}/LIP System and the planned development of the Submersible Walker{trademark}, this situation is due to change. The specifications for these inspection and maintenance robots will ensure that. Their ability to traverse both horizontal and vertical, forward and backward, make them unique tools. They will open the door for some innovative approaches to inspection and maintenance of large pumps and piping systems.

  20. Fiber Bragg grating microphone system for condition-based maintenance of industrial facilities

    NASA Astrophysics Data System (ADS)

    Tosi, D.; Olivero, M.; Perrone, G.; Vallan, A.

    2011-05-01

    This paper presents a multipoint fiber Bragg grating (FBG) sensing system operating as a precision microphone. This instrument aims to become the best performing technology for condition-based maintenance (CBM) of critical elements, like ball bearings and cogwheels, embedded in industrial manufacturing machineries. The system architecture is based on the simple matched-laser principle, leading to a low-cost and high-sensitivity system, operating in time and wavelength multiplexing mode. Then, heavy signal processing is applied, providing an outstanding performance improvement of 59 dB in terms of signal-to-noise ratio. A demonstration of condition-based maintenance operation has been performed using standard models of ball bearing sound spectra. Compared to traditional microphones applied to CBM, the signal processing-powered FBG system provides remarkable advantages in terms of sensitivity and rejection of environment noise, providing an improvement of cost-effectiveness of CBM.

  1. Intelligent systems and advanced user interfaces for design, operation, and maintenance of command management systems

    NASA Technical Reports Server (NTRS)

    Potter, William J.; Mitchell, Christine M.

    1993-01-01

    Historically, command management systems (CMS) have been large and expensive spacecraft-specific software systems that were costly to build, operate, and maintain. Current and emerging hardware, software, and user interface technologies may offer an opportunity to facilitate the initial formulation and design of a spacecraft-specific CMS as well as to develop a more generic CMS system. New technologies, in addition to a core CMS common to a range of spacecraft, may facilitate the training and enhance the efficiency of CMS operations. Current mission operations center (MOC) hardware and software include Unix workstations, the C/C++ programming languages, and an X window interface. This configuration provides the power and flexibility to support sophisticated and intelligent user interfaces that exploit state-of-the-art technologies in human-machine interaction, artificial intelligence, and software engineering. One of the goals of this research is to explore the extent to which technologies developed in the research laboratory can be productively applied in a complex system such as spacecraft command management. Initial examination of some of these issues in CMS design and operation suggests that application of technologies such as intelligent planning, case-based reasoning, human-machine systems design and analysis tools (e.g., operator and designer models), and human-computer interaction tools (e.g., graphics, visualization, and animation) may provide significant savings in the design, operation, and maintenance of the CMS for a specific spacecraft as well as continuity for CMS design and development across spacecraft. The first six months of this research saw a broad investigation by Georgia Tech researchers into the function, design, and operation of current and planned command management systems at Goddard Space Flight Center. As the first step, the researchers attempted to understand the current and anticipated horizons of command management systems at Goddard

  2. Intelligent Systems and Advanced User Interfaces for Design, Operation, and Maintenance of Command Management Systems

    NASA Technical Reports Server (NTRS)

    Mitchell, Christine M.

    1998-01-01

    Historically Command Management Systems (CMS) have been large, expensive, spacecraft-specific software systems that were costly to build, operate, and maintain. Current and emerging hardware, software, and user interface technologies may offer an opportunity to facilitate the initial formulation and design of a spacecraft-specific CMS as well as a to develop a more generic or a set of core components for CMS systems. Current MOC (mission operations center) hardware and software include Unix workstations, the C/C++ and Java programming languages, and X and Java window interfaces representations. This configuration provides the power and flexibility to support sophisticated systems and intelligent user interfaces that exploit state-of-the-art technologies in human-machine systems engineering, decision making, artificial intelligence, and software engineering. One of the goals of this research is to explore the extent to which technologies developed in the research laboratory can be productively applied in a complex system such as spacecraft command management. Initial examination of some of the issues in CMS design and operation suggests that application of technologies such as intelligent planning, case-based reasoning, design and analysis tools from a human-machine systems engineering point of view (e.g., operator and designer models) and human-computer interaction tools, (e.g., graphics, visualization, and animation), may provide significant savings in the design, operation, and maintenance of a spacecraft-specific CMS as well as continuity for CMS design and development across spacecraft with varying needs. The savings in this case is in software reuse at all stages of the software engineering process.

  3. Electro-optical systems to accurately align (boresight) laser designator, FLIR, and CCD on the ground before the mission

    NASA Astrophysics Data System (ADS)

    Cabib, Dario; Segal, Alon; Dolev, Jacob

    2008-10-01

    CI Systems has been involved in the development and production of in-flight boresight equipment since 19891,2, by pioneering the field with innovative laser-FLIR and laser-CCD alignment solutions. In addition, over the years we have developed a number of systems for use on the ground to align the various electro-optical instrumentation to a common Line of Sight (LOS) before the mission. This adjustment is very important for the success of the mission: the more accurate the alignment and its retention during the flight, the better the chance of a precise hit. In this paper we describe various systems developed and built at CI for use with EO pods mounted on aircraft, especially UAV's. The most important engineering tasks are design for small size and convenient mechano-optical interfaces for different pods allowing system compactness, low weight and easy operation. Some of the design considerations to meet these challenges will be given here.

  4. The B-747 flight control system maintenance and reliability data base for cost effectiveness tradeoff studies

    NASA Technical Reports Server (NTRS)

    1982-01-01

    Primary and automatic flight controls are combined for a total flight control reliability and maintenance cost data base using information from two previous reports and additional cost data gathered from a major airline. A comparison of the current B-747 flight control system effects on reliability and operating cost with that of a B-747 designed for an active control wing load alleviation system is provided.

  5. Girder Alignment Plan

    SciTech Connect

    Wolf, Zackary; Ruland, Robert; LeCocq, Catherine; Lundahl, Eric; Levashov, Yurii; Reese, Ed; Rago, Carl; Poling, Ben; Schafer, Donald; Nuhn, Heinz-Dieter; Wienands, Uli; /SLAC

    2010-11-18

    The girders for the LCLS undulator system contain components which must be aligned with high accuracy relative to each other. The alignment is one of the last steps before the girders go into the tunnel, so the alignment must be done efficiently, on a tight schedule. This note documents the alignment plan which includes efficiency and high accuracy. The motivation for girder alignment involves the following considerations. Using beam based alignment, the girder position will be adjusted until the beam goes through the center of the quadrupole and beam finder wire. For the machine to work properly, the undulator axis must be on this line and the center of the undulator beam pipe must be on this line. The physics reasons for the undulator axis and undulator beam pipe axis to be centered on the beam are different, but the alignment tolerance for both are similar. In addition, the beam position monitor must be centered on the beam to preserve its calibration. Thus, the undulator, undulator beam pipe, quadrupole, beam finder wire, and beam position monitor axes must all be aligned to a common line. All relative alignments are equally important, not just, for example, between quadrupole and undulator. We begin by making the common axis the nominal beam axis in the girder coordinate system. All components will be initially aligned to this axis. A more accurate alignment will then position the components relative to each other, without incorporating the girder itself.

  6. Optimal Medical Equipment Maintenance Service Proposal Decision Support System combining Activity Based Costing (ABC) and the Analytic Hierarchy Process (AHP).

    PubMed

    da Rocha, Leticia; Sloane, Elliot; M Bassani, Jose

    2005-01-01

    This study describes a framework to support the choice of the maintenance service (in-house or third party contract) for each category of medical equipment based on: a) the real medical equipment maintenance management system currently used by the biomedical engineering group of the public health system of the Universidade Estadual de Campinas located in Brazil to control the medical equipment maintenance service, b) the Activity Based Costing (ABC) method, and c) the Analytic Hierarchy Process (AHP) method. Results show the cost and performance related to each type of maintenance service. Decision-makers can use these results to evaluate possible strategies for the categories of equipment. PMID:17281912

  7. Installation, maintenance and operating manual for the Lucas-type fuel injection system of the 3 B rotary engine

    NASA Technical Reports Server (NTRS)

    1985-01-01

    The installation procedure, maintenance, adjustment and operation of a Lucas type fuel injection system for 13B rotary racing engine is outlined. Components of the fuel injection system and installation procedure and notes are described. Maintenance, adjustment, and operation are discussed.

  8. Risk management and maintenance optimization of nuclear reactor cooling piping system

    NASA Astrophysics Data System (ADS)

    Augé, L.; Capra, B.; Lasne, M.; Bernard, O.; Bénéfice, P.; Comby, R.

    2006-11-01

    Seaside nuclear power plants have to face the ageing of nuclear reactor cooling piping systems. In order to minimize the duration of the production unit shutdown, maintenance operations have to be planned well in advance. In a context where owners of infrastructures tend to extend the life span of their goods while having to keep the safety level maximum, Oxand brings its expertise and know-how in management of infrastructures life cycle. A dedicated methodology relies on several modules that all participate in fixing network optimum replacement dates: expertise on ageing mechanisms (corrosion, cement degradation...) and the associated kinetics, expertise on impacts of ageing on functional integrity of piping systems, predictive simulation based on experience feedback, development of monitoring techniques focused on actual threats. More precisely, Oxand has designed a patented monitoring technique based on optic fiber sensors, which aims at controlling the deterioration level of piping systems. This preventive maintenance enables the owner to determine criteria for network replacement based on degradation impacts. This approach helps the owner justify his maintenance strategy and allows him to demonstrate the management of safety level. More generally, all monitoring techniques used by the owners are developed and coupled to predictive simulation tools, notably thanks to processes based on Bayesian approaches. Methodologies to evaluate and optimize operation budgets, depending on predictions of future functional deterioration and available maintenance solutions are also developed and applied. Finally, all information related to infrastructure ageing and available maintenance options are put together to reach the right solution for safe and performing infrastructure management.

  9. System and method for aligning heliostats of a solar power tower

    DOEpatents

    Convery, Mark R.

    2013-01-01

    Disclosed is a solar power tower heliostat alignment system and method that includes a solar power tower with a focal area, a plurality of heliostats that each reflect sunlight towards the focal area of the solar power tower, an off-focal area location substantially close to the focal area of the solar power tower, a communication link between the off-focal area location and a misaligned heliostat, and a processor that interprets the communication between the off-focal area location and the misaligned heliostat to identify the misaligned heliostat from the plurality of heliostats and that determines a correction for the identified misaligned heliostat to realign the misaligned heliostat to reflect sunlight towards the focal area of the solar power tower.

  10. Alignment System for Full-Shell Replicated X-Ray Mirrors

    NASA Technical Reports Server (NTRS)

    Gubarev, Mikhail; Arnold, William; Ramsey, Brian

    2009-01-01

    We are developing grazing-incidence x-ray optics for high-energy astrophysical applications using the electroformnickel replication process. For space-based applications these optics must be light-weight yet stable, which dictates the use of very-thin-walled full-shell mirrors. Such shells have been fabricated with resolution as good as 11 arcsec for hard x-rays, and technology enhancements under development at MSFC are aimed at producing mirrors with resolution better than 10 arcsec. The challenge, however, is to preserve this resolution during mounting and assembly. We present here a status report on a mounting and alignment system currently under development at Marshall Space Flight Center designed to meet this challenge.

  11. System for maintaining the alignment of mandrels in filament winding operations

    DOEpatents

    Robinson, S.C.; Dodge, W.G.; Pollard, R.E.

    1983-10-12

    The present invention is directed to a system for sensing and correcting the alignment of a mandrel being wound with filamentary material with respect to the filamentary material winding mechanism. A positioned reference pin attached to the mandrel is positioned in a beam of collimated light emanating from a laser so as to bisect the light beam and create a shadow therebetween. A pair of photocells are positioned to receive the bisected light beam with the shadow uniformly located between the photocells when the pin is in a selected position. The mandrel is supported in the selected position for the winding of a filamentary material by a position adjustable roller mechanism which is coupled by a screw drive to a reversible motor. Changes in the pin position such as caused by winding growth are sensed by the photocells to provide the displacement of the roller mechanism in the direction necessary to return the mandrel to the selected position.

  12. System for maintaining the alignment of mandrels in filament winding operations

    DOEpatents

    Robinson, Samuel C.; Dodge, William G.; Pollard, Roy E.

    1984-01-01

    The present invention is directed to a system for sensing and correcting the alignment of a mandrel being wound with filamentary material with respect to the filamentary material winding mechanism. A positioned reference pin attached to the mandrel is positioned in a beam of collimated light emanating from a laser so as to bisect the light beam and create a shadow therebetween. A pair of photocells are positioned to receive the bisected light beam with the shadow uniformly located between the photocells when the pin is in a selected position. The mandrel is supported in the selected position for the winding of a filamentary material by a position adjustable roller mechanism which is coupled by a screw drive to a reversible motor. Changes in the pin position such as caused by winding growth are sensed by the photocells to provide the displacement of the roller mechanism in the direction necessary to return the mandrel to the selected position.

  13. Transducer-actuator systems and methods for performing on-machine measurements and automatic part alignment

    DOEpatents

    Barkman, William E.; Dow, Thomas A.; Garrard, Kenneth P.; Marston, Zachary

    2016-07-12

    Systems and methods for performing on-machine measurements and automatic part alignment, including: a measurement component operable for determining the position of a part on a machine; and an actuation component operable for adjusting the position of the part by contacting the part with a predetermined force responsive to the determined position of the part. The measurement component consists of a transducer. The actuation component consists of a linear actuator. Optionally, the measurement component and the actuation component consist of a single linear actuator operable for contacting the part with a first lighter force for determining the position of the part and with a second harder force for adjusting the position of the part. The actuation component is utilized in a substantially horizontal configuration and the effects of gravitational drop of the part are accounted for in the force applied and the timing of the contact.

  14. A Medical Decision Support System for the Space Station Health Maintenance Facility

    PubMed Central

    Ostler, David V.; Gardner, Reed M.; Logan, James S.

    1988-01-01

    NASA is developing a Health Maintenance Facility (HMF) to provide the equipment and supplies necessary to deliver medical care in the Space Station. An essential part of the Health Maintenance Facility is a computerized Medical Decision Support System (MDSS) that will enhance the ability of the medical officer (“paramedic” or “physician”) to maintain the crew's health, and to provide emergency medical care. The computer system has four major functions: 1) collect and integrate medical information into an electronic medical record from Space Station medical officers, HMF instrumentation, and exercise equipment; 2) provide an integrated medical record and medical reference information management system; 3) manage inventory for logistical support of supplies and secure pharmaceuticals; 4) supply audio and electronic mail communications between the medical officer and ground based flight surgeons. ImagesFigure 1

  15. Wind energy Computerized Maintenance Management System (CMMS) : data collection recommendations for reliability analysis.

    SciTech Connect

    Peters, Valerie A.; Ogilvie, Alistair; Veers, Paul S.

    2009-09-01

    This report addresses the general data requirements for reliability analysis of fielded wind turbines and other wind plant equipment. The report provides a list of the data needed to support reliability and availability analysis, and gives specific recommendations for a Computerized Maintenance Management System (CMMS) to support automated analysis. This data collection recommendations report was written by Sandia National Laboratories to address the general data requirements for reliability analysis of fielded wind turbines. This report is intended to help the reader develop a basic understanding of what data are needed from a Computerized Maintenance Management System (CMMS) and other data systems, for reliability analysis. The report provides: (1) a list of the data needed to support reliability and availability analysis; and (2) specific recommendations for a CMMS to support automated analysis. Though written for reliability analysis of wind turbines, much of the information is applicable to a wider variety of equipment and a wider variety of analysis and reporting needs.

  16. Comparison of Flux-Surface Aligned Curvilinear Coordinate Systems and Neoclassical Magnetic Field Predictions

    NASA Astrophysics Data System (ADS)

    Collart, T. G.; Stacey, W. M.

    2015-11-01

    Several methods are presented for extending the traditional analytic ``circular'' representation of flux-surface aligned curvilinear coordinate systems to more accurately describe equilibrium plasma geometry and magnetic fields in DIII-D. The formalism originally presented by Miller is extended to include different poloidal variations in the upper and lower hemispheres. A coordinate system based on separate Fourier expansions of major radius and vertical position greatly improves accuracy in edge plasma structure representation. Scale factors and basis vectors for a system formed by expanding the circular model minor radius can be represented using linear combinations of Fourier basis functions. A general method for coordinate system orthogonalization is presented and applied to all curvilinear models. A formalism for the magnetic field structure in these curvilinear models is presented, and the resulting magnetic field predictions are compared against calculations performed in a Cartesian system using an experimentally based EFIT prediction for the Grad-Shafranov equilibrium. Supported by: US DOE under DE-FG02-00ER54538.

  17. Information system design of inventory control spare parts maintenance (valuation class 5000) (case study: plant kw)

    NASA Astrophysics Data System (ADS)

    Fitriana, Rina; Moengin, Parwadi; Riana, Mega

    2016-02-01

    Plat KW hadn't using optimal inventory level planning yet and hadn't have an information system that well computerized. The research objective is to be able to design an information system related inventory control of spare parts maintenance. The study focused on five types of spare parts with the highest application rate during February 2013- March 2015 and included in the classification of fast on FSN analysis Grinding stones Cut 4". Cable Tie 15". Welding RB 26-32MM. Ring Plat ½" and Ring Plate 5/8 ". Inventory calculation used Economic Order Quantity (EOQ). Safety Stock (SS) and Reorder Point (ROP) methods. System analysis conducted using the framework PIECES with the proposed inventory control system. the performance of the plant KW relating to the supply of spare parts maintenance needs can be more efficient as well as problems at the company can be answered and can perform inventory cost savings amounting Rp.267.066. A computerized information system of inventory control spare parts maintenance provides a menu that can be accessed by each departments as the user needed.

  18. Building An Effective and Aligned P-16 Education System: What Should Higher Education do to Enhance Student Access and Success?

    ERIC Educational Resources Information Center

    Governor's Business Council (Texas), 2002

    2002-01-01

    On May 7, 2002, the Governor's Business Council of Texas was honored to host a number of state and national education leaders who came together to discuss higher education's role in creating an effective and aligned P-16 education system. The State of Texas faces a daunting challenge in improving our P-16 system and increasing rates of college…

  19. Cryogenics maintenance strategy

    NASA Astrophysics Data System (ADS)

    Cruzat, Fabiola

    2012-09-01

    ALMA is an interferometer composed of 66 independent systems, with specific maintenance requirements for each subsystem. To optimize the observation time and reduce downtime maintenance, requirements are very demanding. One subsystem with high maintenance efforts is cryogenics and vacuum. To organize the maintenance, the Cryogenic and Vacuum department is using and implementing different tools. These are monitoring and problem reporting systems and CMMS. This leads to different maintenance approaches: Preventive Maintenance, Corrective Maintenance and Condition Based Maintenance. In order to coordinate activities with other departments the preventive maintenance schedule is kept as flexible as systems allow. To cope with unavoidable failures, the team has to be prepared to work under any condition with the spares on time. Computerized maintenance management system (CMMS) will help to manage inventory control for reliable spare part handling, the correct record of work orders and traceability of maintenance activities. For an optimized approach the department is currently evaluating where preventive or condition based maintenance applies to comply with the individual system demand. Considering the change from maintenance contracts to in-house maintenance will help to minimize costs and increase availability of parts. Due to increased number of system and tasks the cryo team needs to grow. Training of all staff members is mandatory, in depth knowledge must be built up by doing complex maintenance activities in the Cryo group, use of advanced computerized metrology systems.

  20. A Framework for Monitoring and Maintenance of a Tsunami Early Warning System using ITIL®

    NASA Astrophysics Data System (ADS)

    Gensch, Stephan; Günther, Michael; Henneberger, Ralph; Strollo, Angelo

    2013-04-01

    Within this work, we present our approach and ongoing efforts to establish monitoring and maintenance processes for Tsunami Early Warning Systems. Practical work is done within the context of the Indonesian Tsunami Warning System (INATEWS) at Badan Meteorologi, Klimatologi dan Geofisika (BMKG) in Jakarta, Indonesia. The German contribution is well known as GITEWS. INATEWS is composed of several thousand integrated system components and numerous software processes. Due to the heterogeneity and complexity of the system, as well as the high availability needs, being an operational TEWS, real-time monitoring, reporting and scheduled preventive maintenance are needed. To develop and install an organizational and operational methodology for maintenance processes for INATEWS, we asserted ITIL® methods and are in development of Standard Operating Procedures (SOP) together with BMKG operational and management staff. ITIL®-conforming methods are one means of IT Service Management which has been adopted by a variety of service oriented IT providers. An early warning system does not expose classical consumer services, but the dissemination of warning messages and an early warning as a product may nevertheless be viewed as distinct services provided by a TEWS. We applied methods from ITIL® to the modular and hierarchical components of an early warning center, where minimum requirements on service availability, reliability and correctness of the warning product exist, from dissemination down to each sensor component. We describe functions of actors that ensure management of incidents and problems, as well as managing applications, IT operations and further technical issues. For the components of the early warning system, we present a model of event detection and event resolution. Real-time monitoring provides automated health-checks. Errors lead to reports to designated targets. Preventive maintenance provides findings on data and system availability, and data quality. Each

  1. An intelligent maintenance system for earth-based failure analysis and self-repairing of microsatellites

    NASA Astrophysics Data System (ADS)

    Sierra, Enrique A.; Quiroga, Juan J.; Fernández, Roberto; Monte, Gustavo E.

    2004-07-01

    This paper describes a recently developed maintenance system for a microsatellite, which is being constructed and it is expected to be launched shortly. The autonomous maintenance system is going to be installed on a personal computer located in an earth-based control room. As this place will most likely be staffed 24 h a day, 7 days a week, there is a good deal of interest in the use of increased automation in maintenance tasks in order to improve the efficiency with which personnel are used and as a way to reduce costs. The system described here is a good example of emerging automation technology that is intended to replace human operators responsible for system maintenance. The structure of the automation system is based upon an architecture of collaborative intelligent agents designed to detect failure in any of the microsatellites components. The multiagent system consists of a set of different agents devoted to failure detection, prevention and correction. Regarding correction, specific agents for each constitutive part of the microsatellite have been developed that take over the necessary actions to solve any given problem in its operation. The detection agent decides which correction agent control should be transferred, based upon inference obtained from its knowledge base made up of rules for testing and diagnosis. Actions for correction may imply the use of redundant systems, which can reconfigure themselves to avoid defective circuits, among other repairing strategies. The prevention agent uses predictive models that have been developed for each significant failure mode. Statistical models are also used by this agent to determine the shape of the distribution of times to failure. The prevention agent selects the corresponding correction agent to which control is going to be transferred and this agent carries out the necessary actions to prevent the system failure. The overall intelligent system employs a blackboard architecture for communication and

  2. Innovation for maintenance technology improvements

    NASA Technical Reports Server (NTRS)

    Shives, T. R. (Editor); Willard, W. A. (Editor)

    1982-01-01

    A group of 34 submitted entries (32 papers and 2 abstracts) from the 33rd meeting of the Mechanical Failures Prevention Group whose subject was maintenance technology improvement through innovation. Areas of special emphasis included maintenance concepts, maintenance analysis systems, improved maintenance processes, innovative maintenance diagnostics and maintenance indicators, and technology improvements for power plant applications.

  3. Transfer alignment from a personal locator system to a handheld or head-mounted instrument

    NASA Astrophysics Data System (ADS)

    Ojeda, Lauro; Borenstein, Johann

    2011-06-01

    This paper presents a method for computing position and attitude of an instrument attached to the human body such as a handheld or head-mounted video camera. The system uses two Inertial Measurement Units (IMUs). One IMU is part of our earlier-developed Personal Dead-Reckoning (PDR) system, which tracks the position and heading of a walking person relative to a known starting position. The other IMU is rigidly attached to the handheld or head-mounted instrument. Our existing PDR system is substantially more accurate than conventional IMU-based systems because the IMU is mounted on the foot of the user where error correction techniques can be applied that are unavailable for IMUs mounted anywhere else on the body. However, if the walker is waving a handheld or head-mounted instrument, the position and attitude of the instrument is not known. Equipping the instrument with an additional IMU is by itself an unsatisfactory solution because that IMU is subject to accelerometer and gyro drift, which, unlike in the case of the foot-mounted IMU, cannot be corrected and cause unbounded position and heading errors. Our approach uses transfer alignment techniques and takes advantage of the fact that the handheld IMU moves with the walker. This constraint is used to bound and correct errors by a Kalman filter. The paper explains our method and presents extensive experimental results. The results show up to a five-fold reduction in heading errors for the handheld IMU.

  4. Plasma drifts associated with a system of sun-aligned arcs in the polar cap

    SciTech Connect

    Mende, S.B.; Doolittle, J.H.; Robinson, R.M.; Vondrak, R.R.; Rich, F.J.

    1988-01-01

    A series of four sun-aligned arcs passed over Sondre Stromfjord, Greenland, on the night of the 17th and 18th of February, 1985. Observations of these arcs were made using the Sondrestrom incoherent scatter radar and an intensified all-sky imaging TV system that was operated at the radar site. The first of the four arcs crossed the Sondre Stromfjord meridian just before local midnight moving westward, and the other three arcs followed at approximately half-hour intervals. When we account for the earth's rotation, the arc drift in an inertial frame was eastward, or dusk to dawn. The half-hour interval between meridian crossings of the arcs implies that the mean spacing between the arcs was 180 km. A Defense Meteorological Satellite Program (DMSP) F6 satellite pass at 0110 UT revealed the presence of highly structured electron and ion precipitation throughout the polar cap. The DMSP visible imager detected a single, sun-aligned arc associated with the largest peak in precipitating electron flux. This arc was also observed at Thule, Greenland, with an intensified film camera. These observations suggest that at least one of the arcs that were observed at Sondre Stromfjord extended across a large part of the polar cap. The radar at Sondre Stromfjord measured electron density and ion drift velocities associated with the four arcs. The radar drift measurements were superimposed on the all-sky video images to determine the location of the measurements relative to the arcs. Plasma drifts outside the arcs were found to be both sunward and antisunward, while within the arcs the drifts were predominantly antisunward. The variability of the drifts in the direction parallel to the arcs indicates that the electric fields were highly structured even though the configuration and motion of the arcs were well behaved.

  5. Climatology of the inter-hemispheric field-aligned currents system over the Nigeria ionosphere

    NASA Astrophysics Data System (ADS)

    Bolaji, O. S.; Rabiu, A. B.; Oyeyemi, E. O.; Yumoto, K.

    2012-11-01

    Records of the declination (D) magnetic field data for the year 2009 from the Magnetic Data Acquisition System (MAGDAS) facilities at University of Ilorin were employed for this work. From the minutes value of the D-component, the deduced hourly values of the D-component (Sq(QD)) were used to estimate its diurnal (Sq(D)) values with the most five quietest days identified. The monthly mean (MSq(D)) of the most five quietest days and their seasonal (SSq(D)) variabilities were investigated. The inter-hemispheric field aligned currents (IHFACs) exhibit downward and upward inter-hemispheric field-aligned sheet current that appears as a pair at all local times of the Sq(D), MSq(D), and SSq(D) variations. From these variabilities, the IHFACs were observed to flow from the winter to summer hemisphere during noon and dusk sector and flowing in opposite direction during the dawn sector. The Sq(D) variability patterns that were observed in May, June, August September are gentle compared to the disturbed variabilities in January, February, March and November. The highest positive (˜1.7 arc-min) and negative (˜-2.7 arc min) MSq(D) maxima values were observed in August during the dawn and noon sectors respectively. These values indicated that the IHFACs flow in August is strongly southbound (positive) and northbound (negative) in the dawn and noon sectors respectively. Dusk-side IHFACs as can be observed by MAGDAS are weakly northbound in all the seasons. The direction of IHFACs does not flip at the equinoxes but in June and November and does not become largest at solstices but in August. The IHFACs was observed to exhibit longitudinal variability, which indicated that larger amplitude of winter-to-summer IHFACs is observed to be greater in June solstice (northbound/negative IHFACs) than in the December solstice (southbound/positive IHFACs) during the noon sector.

  6. Development of an Ion Beam Irradiation System for Liquid Crystal Alignment Layer Production

    SciTech Connect

    Matsumoto, Takeshi; Kinoshita, Yuko; Tanii, Masahiro; Tatemichi, Junichi; Konishi, Masashi; Naito, Masao

    2008-11-03

    Ion beam irradiation was employed to produce alignment layers for liquid crystal (LC) displays. The alignment characteristics were compared with those by the conventional rubbing method. Ion incident angle to the films played an important role in LC sample optical qualities. A new ion irradiation method to realize a multi-domain structure for a wide viewing angle was demonstrated.

  7. Gauging Item Alignment through Online Systems While Controlling for Rater Effects

    ERIC Educational Resources Information Center

    Anderson, Daniel; Irvin, Shawn; Alonzo, Julie; Tindal, Gerald A.

    2015-01-01

    The alignment of test items to content standards is critical to the validity of decisions made from standards-based tests. Generally, alignment is determined based on judgments made by a panel of content experts with either ratings averaged or via a consensus reached through discussion. When the pool of items to be reviewed is large, or the…

  8. Long-range maintenance planning: A case study of working system

    SciTech Connect

    Flanigan, M.J.

    1991-10-01

    This paper addresses the development of the Lawrence Livermore National Laboratory (LLNL) Maintenance Planning System (MPS). The pitfalls encountered and overcome, and future expansion plans. The MPS provides the ability to develop and track long-range programs, i.e., conversion of chlorofluorocarbon (CFC) equipment to hydrochlorofluorocaron (HCFC), roofing, roads, etc., in addition to providing invaluable information and data for current year budget justification.

  9. Recent Technology of Sensing, Monitoring, Diagnosis, and Maintenance for Aged Electric Power and Energy System

    NASA Astrophysics Data System (ADS)

    Matsumoto, Satoshi

    This paper deals with the recent topics related to sensing, monitoring, and diagnosis for electric power equipment. Moreover the risk management for such equipments has been an object of study in many terms such as economical, technical aspects, safety and rest, CSR (Corporate Social Responsibility) etc. The relationship between the function of the economic engineering and the maintenance strategy for electric power system are reviewed.

  10. Using Stars to Align a Steered Laser System for Cosmic Ray Simulation

    NASA Astrophysics Data System (ADS)

    Krantz, Harry; Wiencke, Lawrence

    2016-03-01

    Ultra high energy cosmic rays (UHECRs) are the highest energy cosmic particles with kinetic energy above 1018eV . UHECRs are detected from the air shower of secondary particles and UV florescence that results from interaction with the atmosphere. A high power UV laser beam can be used to simulate the optical signature of a UHCER air shower. The Global Light System (GLS) is a planned network of ground-based light sources including lasers to support the planned space-based Extreme Universe Space Observatory (EUSO). A portable prototype GLS laser station has been constructed at the Colorado School of Mines. Currently the laser system uses reference targets on the ground but stars can be used to better align the beam by providing a complete hemisphere of targets. In this work, a CCD camera is used to capture images of known stars through the steering head optics. The images are analyzed to find the steering head coordinates of the target star. The true coordinates of the star are calculated from the location and time of observation. A universal adjustment for the steering head is determined from the differences between the two pairs of coordinates across multiple stars. This laser system prototype will also be used for preflight tests of the ESUO Super Pressure Balloon mission.

  11. An Intelligent Dynamic Alignment System for Interferometer of Fourier Transform Spectrometer

    NASA Astrophysics Data System (ADS)

    Yang, Kun; Zeng, Libo

    An intelligent dynamic alignment system for a Michelson interferometer which is applied to a Mid-infrared band Fourier transform spectrometer (FTS) is presented. Three photodiodes are used to detect the tilt of moving mirror opposite to fixed mirror with the assistance of the interfered signal of a reference He-Ne laser. This technique is based on detecting the phase difference of laser signal between every two diodes in two perpendicular directions. And four magnetic actuators behind the mounting brace of fixed mirror are used to change the pose of fixed mirror. The system is controlled by a digital signal processor (DSP) in real-time. A feedback algorithm is used to tilt fixed mirror following the action of moving mirror so as to keep both mirror planes in perpendicular. Experiment result shows that the relative tilt between two reflecting mirrors can be restricted in a range no more than ±1.5×10-6rad. This system is effective and reliable to be applied to scanning interferometer of Fourier transform spectrometer.

  12. Wind energy Computerized Maintenance Management System (CMMS) : data collection recommendations for reliability analysis.

    SciTech Connect

    Peters, Valerie A.; Ogilvie, Alistair B.

    2012-01-01

    This report addresses the general data requirements for reliability analysis of fielded wind turbines and other wind plant equipment. The report provides a rationale for why this data should be collected, a list of the data needed to support reliability and availability analysis, and specific data recommendations for a Computerized Maintenance Management System (CMMS) to support automated analysis. This data collection recommendations report was written by Sandia National Laboratories to address the general data requirements for reliability analysis of operating wind turbines. This report is intended to help develop a basic understanding of the data needed for reliability analysis from a Computerized Maintenance Management System (CMMS) and other data systems. The report provides a rationale for why this data should be collected, a list of the data needed to support reliability and availability analysis, and specific recommendations for a CMMS to support automated analysis. Though written for reliability analysis of wind turbines, much of the information is applicable to a wider variety of equipment and analysis and reporting needs. The 'Motivation' section of this report provides a rationale for collecting and analyzing field data for reliability analysis. The benefits of this type of effort can include increased energy delivered, decreased operating costs, enhanced preventive maintenance schedules, solutions to issues with the largest payback, and identification of early failure indicators.

  13. Expanding the domain of a prototype expert system with an eye on future maintenance - The FIESTA case study

    NASA Technical Reports Server (NTRS)

    Happell, Nadine; Miksell, Steven G.

    1989-01-01

    The methods by which an expert system architecture can support such key elements of domain expansion and maintenance as knowledge acquisition, representation, addition, and modification, are presently illustrated by the Fault Isolation Expert System for TDRSS Applications (FIESTA). FIESTA highlights such similarities between conventional software engineering and expert system development as the benefits that accrue to loose coupling, modularity, and documentation. A major difference, however, is the set of opportunities afforded automated end-user maintenance by expert system technology.

  14. 40 CFR 52.2348 - National Highway Systems Designation Act Motor Vehicle Inspection and Maintenance (I/M) Programs.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 4 2011-07-01 2011-07-01 false National Highway Systems Designation Act Motor Vehicle Inspection and Maintenance (I/M) Programs. 52.2348 Section 52.2348 Protection of... and Maintenance (I/M) Programs. (a) On March 15, 1996 the Governor of Utah submitted a revised...

  15. 40 CFR 52.2348 - National Highway Systems Designation Act Motor Vehicle Inspection and Maintenance (I/M) Programs.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 4 2010-07-01 2010-07-01 false National Highway Systems Designation Act Motor Vehicle Inspection and Maintenance (I/M) Programs. 52.2348 Section 52.2348 Protection of... and Maintenance (I/M) Programs. (a) On March 15, 1996 the Governor of Utah submitted a revised...

  16. Intelligent user interface for expert systems applied to power plant maintenance and troubleshooting

    SciTech Connect

    Kock, C.G.; Isle, B.A.; Butler, A.W.

    1988-03-01

    A research and development project is under way to specify, design, construct, and evaluate a user interface system to meet the unique requirements of a delivery vehicle for a knowledge-based system applied to gas turbine electronics equipment maintenance and troubleshooting. The user interface is a portable device with text display, video and overlay graphics display, voice recognition and speech production, special-function keypad, and printer. A modular software structure based on a serial communications protocol between user interface device and expert system host computer provides flexibility, expandability, and a simple, effective user interface dialogue.

  17. Maintenance of Different Mannitol Uptake Systems during Starvation in Oxidative and Fermentative Marine Bacteria

    PubMed Central

    Davis, Claire L.; Robb, Frank T.

    1985-01-01

    The mannitol uptake systems in marine Vibrio and Pseudomonas isolates from the kelp beds off the South African west coast were examined. The fermentative Vibrio isolate possessed a constitutive rapid mannitol uptake system and also a soluble mannitol-1-phosphate dehydrogenase, indicative of a mannitol phosphotransferase system. An inducible, relatively less active mannitol uptake system was detected in the oxidative Pseudomonas isolate, and this strain possessed a mannitol dehydrogenase. The maintenance of these systems during starvation survival was studied. The Vibrio isolate maintained its initial uptake system for approximately 5 weeks of starvation, after which time the uptake system was replaced by one with a higher affinity for mannitol. The mannitol transport system of the Pseudomonas isolate was depressed early in starvation (30 h) but could be readily induced by exogenous mannitol after 6 weeks of starvation. The relative proportions of mannitol which was incorporated and respired were determined in starved Vibrio and Pseudomonas strains. PMID:16346909

  18. Heteroepitaxial formation of aligned mesostructured silica films with large structural periodicities from mixed surfactant systems.

    PubMed

    Hayase, Saeko; Kanno, Yosuke; Watanabe, Masatoshi; Takahashi, Masahiko; Kuroda, Kazuyuki; Miyata, Hirokatsu

    2013-06-11

    Liquid-crystal phases consisting of cylindrical micelles of amphiphilic block copolymers and silica precursors are epitaxially built up on aligned surface micelles formed by an alkyl-PEO surfactant, Brij56, irrespective of the large difference in the intrinsic structural periodicities resulting in the formation of fully aligned mesostructured silica films with large lattice constants. Brij56 works as an alignment controlling agent on rubbing-treated polyimide through selective adsorption from a precursor solution containing the two surfactants, a block copolymer and Brij56, through strong hydrophobic interactions to form an anisotropic surface micelle structure. Aligned mesostructured silica layers with larger periodicities, which dominantly consist of block copolymers, form on these aligned surface micelles by gradually changing the vertical periodicity keeping the lateral intermicelle distance constant. This can be regarded as a kind of heteroepitaxy because the lattice constant at the surface is different from that of the bulk of the film. On the basis of this new concept, highly aligned mesostructured silica films with structural periodicities as large as 10 nm are successfully formed, which has never been achieved when the block copolymers are used alone as the structure-directing agent. The periodicity of the aligned films can precisely be controlled by an appropriate choice of block copolymers and the mixing ratio of the two surfactants, which increases the opportunity for applications of these films with highly anisotropic mesoscale structure. PMID:23721098

  19. When a single hole aligns several spins: Double exchange in organic systems

    SciTech Connect

    Trinquier, Georges; Chilkuri, Vijay Gopal; Malrieu, Jean-Paul

    2014-05-28

    The double exchange is a well-known and technically important phenomenon in solid state physics. Ionizing a system composed of two antiferromagnetically coupled high-spin units, the ground state of which is a singlet state, may actually produce a high-spin ground state. This work illustrates the possible occurrence of such a phenomenon in organic chemistry. The here-considered high-spin units are triangulenes, the ground state of which is a triplet. Bridging two of them through a benzene ring produces a molecular architecture of singlet ground state. A careful exploitation of a series of unrestricted density functional calculations enables one to avoid spin contamination in the treatment of the doublet states and shows that under ionization the system becomes of quartet multiplicity in its ground state. The possibility to align more than three spins from conjugated hydrocarbon polyradicals is explored, considering partially hydrogenated triangulenes. A dramatic example shows that ionization of a singlet ground state molecule may generate a decuplet.

  20. A Toolbox of Metrology-Based Techniques for Optical System Alignment

    NASA Technical Reports Server (NTRS)

    Coulter, Phillip; Ohl, Raymond G.; Blake, Peter N.; Bos, Brent J.; Casto, Gordon V.; Eichhorn, William L.; Gum, Jeffrey S.; Hadjimichael, Theodore J.; Hagopian, John G.; Hayden, Joseph E.; Hicks, Samantha L.; Kubalak, Dave; Mclean, Kyle F.; McMann, Joseph; Redman, Kevin; Wenzel, Greg; Young, Jerrod

    2016-01-01

    The NASA Goddard Space Flight Center (GSFC) and its partners have broad experience in the alignment of flight optical instruments and spacecraft structures. Over decades, GSFC developed alignment capabilities and techniques for a variety of optical and aerospace applications. In this paper, we provide an overview of a subset of the capabilities and techniques used on several recent projects in a toolbox format. We discuss a range of applications, from small-scale optical alignment of sensors to mirror and bench examples that make use of various large-volume metrology techniques. We also discuss instruments and analytical tools.

  1. Alignment issues, correlation techniques and their assessment for a visible light imaging-based 3D printer quality control system

    NASA Astrophysics Data System (ADS)

    Straub, Jeremy

    2016-05-01

    Quality control is critical to manufacturing. Frequently, techniques are used to define object conformity bounds, based on historical quality data. This paper considers techniques for bespoke and small batch jobs that are not statistical model based. These techniques also serve jobs where 100% validation is needed due to the mission or safety critical nature of particular parts. One issue with this type of system is alignment discrepancies between the generated model and the physical part. This paper discusses and evaluates techniques for characterizing and correcting alignment issues between the projected and perceived data sets to prevent errors attributable to misalignment.

  2. Alignment of a tiled-grating compressor in a high-power chirped-pulse amplification laser system.

    PubMed

    Hornung, Marco; Bödefeld, Ragnar; Siebold, Mathias; Schnepp, Matthias; Hein, Joachim; Sauerbrey, Roland; Kaluza, Malte C

    2007-10-20

    We present a novel technique to align a tiled grating in all five relevant degrees of freedom utilized in the compressor of the high-power chirped-pulse amplification laser system POLARIS at the Institute for Optics and Quantum Electronics, Jena, Germany. With this technique, alignment errors of the two gratings with respect to each other can be detected with an accuracy of 1 microrad for the rotational and 40 nm for the translational degrees of freedom. This is well sufficient to recompress 1030 nm pulses, which were stretched to 2.2 ns before amplification, to their bandwith limit of 150 fs. PMID:17952178

  3. Consensus-Based Course Design and Implementation of Constructive Alignment Theory in a Power System Analysis Course

    ERIC Educational Resources Information Center

    Vanfretti, Luigi; Farrokhabadi, Mostafa

    2015-01-01

    This article presents the implementation of the constructive alignment theory (CAT) in a power system analysis course through a consensus-based course design process. The consensus-based design process involves both the instructor and graduate-level students and it aims to develop the CAT framework in a holistic manner with the goal of including…

  4. Maintenance-free lead acid battery for inertial navigation systems aircraft

    NASA Astrophysics Data System (ADS)

    Johnson, William R.; Vutetakis, David G.

    1995-05-01

    Historically, Aircraft Inertial Navigation System (INS) Batteries have utilized vented nickel-cadmium batteries for emergency DC power. The United States Navy and Air Force developed separate systems during their respective INS developments. The Navy contracted with Litton Industries to produce the LTN-72 and Air Force contracted with Delco to produce the Carousel IV INS for the large cargo and specialty aircraft applications. Over the years, a total of eight different battery national stock numbers (NSNs) have entered the stock system along with 75 battery spare part NSNs. The Standard Hardware Acquisition and Reliability Program is working with the Aircraft Battery Group at Naval Surface Warfare Center Crane Division, Naval Air Systems Command (AIR 536), Wright Laboratory, Battelle Memorial Institute, and Concorde Battery Corporation to produce a standard INS battery. This paper discusses the approach taken to determine whether the battery should be replaced and to select the replacement chemistry. The paper also discusses the battery requirements, aircraft that the battery is compatible with, and status of Navy flight evaluation. Projected savings in avoided maintenance in Navy and Air Force INS Systems is projected to be $14.7 million per year with a manpower reduction of 153 maintenance personnel. The new INS battery is compatible with commercially sold INS systems which represents 66 percent of the systems sold.

  5. System maintenance manual for master modeling of aerodynamic surfaces by three-dimensional explicit representation

    NASA Technical Reports Server (NTRS)

    Gibson, A. F.

    1983-01-01

    A system of computer programs has been developed to model general three-dimensional surfaces. Surfaces are modeled as sets of parametric bicubic patches. There are also capabilities to transform coordinate to compute mesh/surface intersection normals, and to format input data for a transonic potential flow analysis. A graphical display of surface models and intersection normals is available. There are additional capabilities to regulate point spacing on input curves and to compute surface intersection curves. Internal details of the implementation of this system are explained, and maintenance procedures are specified.

  6. Calibration grooming and alignment for LDUA High Resolution Stereoscopic Video Camera System (HRSVS)

    SciTech Connect

    Pardini, A.F.

    1998-01-27

    The High Resolution Stereoscopic Video Camera System (HRSVS) was designed by the Savannah River Technology Center (SRTC) to provide routine and troubleshooting views of tank interiors during characterization and remediation phases of underground storage tank (UST) processing. The HRSVS is a dual color camera system designed to provide stereo viewing of the interior of the tanks including the tank wall in a Class 1, Division 1, flammable atmosphere. The HRSVS was designed with a modular philosophy for easy maintenance and configuration modifications. During operation of the system with the LDUA, the control of the camera system will be performed by the LDUA supervisory data acquisition system (SDAS). Video and control status 1458 will be displayed on monitors within the LDUA control center. All control functions are accessible from the front panel of the control box located within the Operations Control Trailer (OCT). The LDUA will provide all positioning functions within the waste tank for the end effector. Various electronic measurement instruments will be used to perform CG and A activities. The instruments may include a digital volt meter, oscilloscope, signal generator, and other electronic repair equipment. None of these instruments will need to be calibrated beyond what comes from the manufacturer. During CG and A a temperature indicating device will be used to measure the temperature of the outside of the HRSVS from initial startup until the temperature has stabilized. This device will not need to be in calibration during CG and A but will have to have a current calibration sticker from the Standards Laboratory during any acceptance testing. This sensor will not need to be in calibration during CG and A but will have to have a current calibration sticker from the Standards Laboratory during any acceptance testing.

  7. Operations and maintenance manual for the LDUA supervisory control and data acquisition system (LDUA System 4200) and control network (LDUA System 4400)

    SciTech Connect

    Barnes, G.A.

    1998-03-11

    This document defines the requirements applicable to the operation, maintenance and storage of the Supervisory Control and Data Acquisition System (SCADAS) and Control Network in support of the Light Duty Utility Arm (LDUA) operations.

  8. Using string alignment in a query-by-humming system for real world applications

    NASA Astrophysics Data System (ADS)

    Sailer, Christian

    2005-09-01

    Though query by humming (i.e., retrieving music or information about music by singing a characteristic melody) has been a popular research topic during the past decade, few approaches have reached a level of usefulness beyond mere scientific interest. One of the main problems is the inherent contradiction between error tolerance and dicriminative power in conventional melody matching algorithms that rely on a melody contour approach to handle intonation or transcription errors. Adopting the string matching/alignment techniques from bioinformatics to melody sequences allows to directly assess the similarity between two melodies. This method takes an MPEG-7 compliant melody sequence (i.e., a list of note intervals and length ratios) as query and evaluates the steps necessary to transform it into the reference sequence. By introducing a musically founded cost-of-replace function and an adequate post processing, this method yields a measure for melodic similarity. Thus it is possible to construct a query by humming system that can properly discriminate between thousands of melodies and still be sufficiently error tolerant to be used by untrained singers. The robustness has been verified in extensive tests and real world applications.

  9. Four large-scale field-aligned current systems in the dayside high-latitude region

    SciTech Connect

    Ohtani, S.; Potemra, T.A.; Newell, P.T.

    1995-01-01

    A system of four current sheets of large-scale field-aligned currents (FACs) was discovered in the data set of simultaneous Viking and DMSP-F7 crossings of the dayside high-latitude region. This paper reports four examples of this system that were observed in the prenoon sector. The flow polarities of FACs are upward, downward, upward, and downward, from equatorward to poleward. The lowest-latitude upward current is flowing mostly in the CPS precipitation region, often overlapping with the BPS at its poleward edge, and is interpreted as a region 2 current. The pair of downward and upward FACs in the middle of the structure are collocated with structured electron precipitation. The precipitation of high-energy (>1 keV) electrons is more intense in the lower-latitude downward current sheet. The highest-latitude downward flowing current sheet is located in a weak, low-energy particle precipitation region, suggesting that this current is flowing on open field lines. Simultaneous observations in the postnoon local time sector reveal the standard three-sheet structure of FACs, sometimes described as region 2, region 1, and mantle (referred to the midday region 0) currents. A high correlation was found between the occurrence of the four FAC sheet structure and negative interplanetary magnetic field (IMF) B{sub Y}. The authors discuss the FAC structure in terms of three types of convection cells: the merging, viscous, and lobe cells. During strongly negative IMF B{sub Y}, two convection reversals exist in the prenoon sector; one is inside the viscous cell, and the other is between the viscous cell and the lobe cell. This structure of convection flow is supported by the Viking electric field and auroral UV image data. Based on the convection pattern, the four FAC sheet structure is interpreted as the latitudinal overlap of midday and morning FAC systems. 47 refs., 12 figs., 1 tab.

  10. Risk and performance based techniques in system health and maintenance monitoring

    NASA Astrophysics Data System (ADS)

    Hadavi, Seyed Mohammad Hadi

    Integrating the risk and reliability analysis, system topology, and database manipulation methodologies into a unified system-health and performance monitoring tool has a great potential for improving plant operation and safety. A methodology has been developed in this study to integrate three basic elements of a performance monitoring system: data, analytical models, and system relations. In this methodology, the plant topology plays the major role. It defines the relationships among plant components, systems and structures. It provides the system configurations and causal relationships needed for performing risk and performance analyses. The causal relationships modeled by the plant topology are very crucial for evaluating the plant condition, safety. Integrating performance analysis tool with plant topology and also integrating it with the various classes of information is another aspect of the methodology proposed by this research. The use of plant topology is a replacement for arrays of logics which usually construct the knowledge-base of an inference engine. The expansion of the plant topology as the basis for explaining the relationships among plant components, systems, and structures, captures the dynamics of plant condition. It is one of the major contributions of this study. In addition, a maintenance schedule optimization technique has been developed and integrated. The main objective of this optimizer, build based on the genetic algorithm methodology, has been to reduce the risk and the cost of maintenance operation. The genetic algorithm is a relatively new technology which mimics the concept of natural evolution processes. The general features of a traditional genetic algorithm have been modified in this study to better fit the requirements of maintenance activities and conditions. The impact of each potential schedule on both plant safety and economy, has been evaluated using a disvalue function. The impact of schedule lineup on plant safety is

  11. System-level biomechanical approach for the evaluation of term and preterm pregnancy maintenance.

    PubMed

    Mahmoud, Hussam; Wagoner Johnson, Amy; Chien, Edward K; Poellmann, Michael J; McFarlin, Barbara

    2013-02-01

    Preterm birth is the primary contributor to perinatal morbidity and mortality, with those born prior to 32 weeks disproportionately contributing compared to those born at 32-37 weeks. Outcomes for babies born prematurely can be devastating. Parturition is recognized as a mechanical process that involves the two processes that are required to initiate labor: rhythmic myometrial contractions and cervical remodeling with subsequent dilation. Studies of parturition tend to separate these two processes rather than evaluate them as a unified system. The mechanical property characterization of the cervix has been primarily performed on isolated cervical tissue, with an implied understanding of the contribution from the uterine corpus. Few studies have evaluated the function of the uterine corpus in the absence of myometrial contractions or in relationship to retaining the fetus. Therefore, the cervical-uterine interaction has largely been neglected in the literature. We suggest that a system-level biomechanical approach is needed to understand pregnancy maintenance. To that end, this paper has two main goals. One goal is to highlight the gaps in current knowledge that need to be addressed in order to develop any comprehensive and clinically relevant models of the system. The second goal is to illustrate the utility of finite element models in understanding pregnancy maintenance of the cervical-uterine system. The paper targets an audience that includes the reproductive biologist/clinician and the engineer/physical scientist interested in biomechanics and the system level behavior of tissues. PMID:23445054

  12. A remote telepresence robotic system for inspection and maintenance of a nuclear power plant. Annual research status report

    SciTech Connect

    Crane, C.D. III; Tulenko, J.S.

    1993-02-01

    Progress in reported in the areas of environmental hardening; database/world modeling; man-machine interface; development of the Advanced Liquid Metal Reactor (ALMR) maintenance inspection robot design; and Articulated Transporter/Manipulator System (ATMS) development.

  13. Opposed port alignment system (OPAS): a commercial astronomical telescope modified for viewing the interior of the NIF target chamber

    NASA Astrophysics Data System (ADS)

    Manuel, Anastacia M.; McCarville, Tom J.; Seppala, Lynn G.; Klingmann, Jeff L.; Kalantar, Daniel H.

    2012-10-01

    The National Ignition Facility (NIF) requires high resolution live images of regions inside the target chamber in order to align diagnostic instruments to fusion targets and to monitor target stability. To view the interior of the target chamber, we modified a commercial 11-inch Schmidt-Cassegrain telescope to develop the Opposed Port Alignment System (OPAS). There are two OPAS systems installed on the target chamber ports directly opposite the diagnostics. This paper describes the optical design, highlighting the two key modifications of the telescope. The first key modification was to reposition the Schmidt corrector plate and to uniquely mount the secondary mirror to a precision translation stage to adjust focus from 5.5 m to infinity. The stage is carefully aligned to ensure that the telescope's optical axis lies on a straight line during focus adjustments. The second key modification was a custom three element lens that flattens the field, corrects residual aberrations of the Schmidt-Cassegrain and, with a commercial 1:1 relay lens, projects the final image plane onto a large format 50 mega-pixel camera. The OPAS modifications greatly extend the Schmidt-Cassegrain telescope's field of view, producing nearly diffraction-limited images over a flat field covering +/-0.4 degrees. Also discussed in the paper are the alignment procedure and the hardware layout of the telescope.

  14. Comparing HARPS and Kepler surveys. The alignment of multiple-planet systems

    NASA Astrophysics Data System (ADS)

    Figueira, P.; Marmier, M.; Boué, G.; Lovis, C.; Santos, N. C.; Montalto, M.; Udry, S.; Pepe, F.; Mayor, M.

    2012-05-01

    Context. The recent results of the HARPS and Kepler surveys provided us with a bounty of extrasolar systems. While the two teams extensively analyzed each of their data-sets, little work has been done comparing the two. Aims: We study a subset of the planetary population whose characterization is simultaneously within reach of both instruments. We compare the statistical properties of planets in systems with msini > 5-10 M⊕ and R > 2 R⊕, as inferred from the HARPS and Kepler surveys, respectively. If we assume that the underlying population has the same characteristics, the different detection sensitivity to the orbital inclination relative to the line of sight allows us to probe the planets' mutual inclination. Methods: We considered the frequency of systems with one, two, and three planets as dictated by HARPS data. We used Kepler's planetary period and host mass and radius distributions (corrected from detection bias) to model planetary systems in a simple, yet physically plausible way. We then varied the mutual inclination between planets in a system according to different prescriptions (completely aligned, Rayleigh distributions, and isotropic) and compared the transit frequencies with one, two, or three planets with those measured by Kepler. Results: The results show that the two datasets are compatible, a remarkable result especially because there are no tunable knobs other than the assumed inclination distribution. For msini cutoffs of 7-10 M⊕, which are those expected to correspond to the radius cutoff of 2 R⊕, we conclude that the results are better described by a Rayleigh distribution with a mode of 1° or smaller. We show that the best-fit scenario only becomes a Rayleigh distribution with a mode of 5° if we assume a quite extreme mass-radius relationship for the planetary population. Conclusions: These results have important consequences for our understanding of the role of several proposed formation and evolution mechanisms. They confirm that

  15. Sequential energy and electron transfer in a three-component system aligned on a clay nanosheet.

    PubMed

    Fujimura, Takuya; Ramasamy, Elamparuthi; Ishida, Yohei; Shimada, Tetsuya; Takagi, Shinsuke; Ramamurthy, Vaidhyanathan

    2016-02-21

    To achieve the goal of energy transfer and subsequent electron transfer across three molecules, a phenomenon often utilized in artificial light harvesting systems, we have assembled a light absorber (that also serves as an energy donor), an energy acceptor (that also serves as an electron donor) and an electron acceptor on the surface of an anionic clay nanosheet. Since neutral organic molecules have no tendency to adsorb onto the anionic surface of clay, a positively charged water-soluble organic capsule was used to hold neutral light absorbers on the above surface. A three-component assembly was prepared by the co-adsorption of a cationic bipyridinium derivative, cationic zinc porphyrin and cationic octaamine encapsulated 2-acetylanthracene on an exfoliated anionic clay surface in water. Energy and electron transfer phenomena were monitored by steady state fluorescence and picosecond time resolved fluorescence decay. The excitation of 2-acetylanthracene in the three-component system resulted in energy transfer from 2-acetylanthracene to zinc porphyrin with 71% efficiency. Very little loss due to electron transfer from 2-acetylanthracene in the cavitand to the bipyridinium derivative was noticed. Energy transfer was followed by electron transfer from the zinc porphyrin to the cationic bipyridinium derivative with 81% efficiency. Analyses of fluorescence decay profiles confirmed the occurrence of energy transfer and subsequent electron transfer. Merging the concepts of supramolecular chemistry and surface chemistry we realized sequential energy and electron transfer between three hydrophobic molecules in water. Exfoliated transparent saponite clay served as a matrix to align the three photoactive molecules at a close distance in aqueous solutions. PMID:26820105

  16. A Case Study of the Alignment between Curriculum and Assessment in the New York State Earth Science Standards-Based System

    ERIC Educational Resources Information Center

    Contino, Julie

    2013-01-01

    In a standards-based system, it is important for all components of the system to align in order to achieve the intended goals. No Child Left Behind law mandates that assessments be fully aligned with state standards, be valid, reliable and fair, be reported to all stakeholders, and provide evidence that all students in the state are meeting the…

  17. The Alignment System for a Medium-Sized Schwarzschild-Couder Telescope Prototype for the Cherenkov Telescope Array

    NASA Astrophysics Data System (ADS)

    Ribeiro, Deivid; Humensky, Brian; Nieto, Daniel; V Vassiliev Group in UCLA division of Astronomy and Astrophysics, P Kaaret Group at Iowa University Department of Physics and Astronomy, CTA Consortium

    2016-01-01

    The Cherenkov Telescope Array (CTA) is an international project for a next-generation ground-based gamma-ray observatory. CTA, conceived as an array of tens of imaging atmospheric Cherenkov telescopes, comprising small, medium and large-size telescopes, is aiming to improve on the sensitivity of current-generation experiments by an order of magnitude and provide energy coverage from 20 GeV to more than 300 TeV. The Schwarzschild-Couder design is a candidate 9-m diameter medium-sized telescope featuring a novel aplanatic two-mirror optical design capable of a wide field of view with significantly improved imaging resolution as compared to the traditional Davies-Cotton optical design. Achieving this imaging resolution imposes strict mirror alignment requirements that necessitate a sophisticated alignment system. This system uses a collection of position sensors between panels to determine the relative position of adjacent panels; each panel is mounted on a Stewart platform to allow motion control with six degrees of freedom, facilitating the alignment of the optical surface for the segmented primary and secondary mirrors. Alignments of the primary and secondary mirrors and the camera focal plane with respect to each other are performed utilizing a set of CCD cameras which image LEDs placed on the mirror panels to measure relative translation, and custom-built auto-collimators to measure relative tilt between the primary and secondary mirrors along the optical axis of the telescope. In this contribution we present the status of the development of the SC optical alignment system, soon to be materialized in a full-scale prototype SC medium-size telescope (pSCT) at the Fred Lawrence Whipple Observatory in southern Arizona.

  18. The maintenance and regeneration of the planarian excretory system are regulated by EGFR signaling.

    PubMed

    Rink, Jochen C; Vu, Hanh Thi-Kim; Sánchez Alvarado, Alejandro

    2011-09-01

    The maintenance of organs and their regeneration in case of injury are crucial to the survival of all animals. High rates of tissue turnover and nearly unlimited regenerative capabilities make planarian flatworms an ideal system with which to investigate these important processes, yet little is known about the cell biology and anatomy of their organs. Here we focus on the planarian excretory system, which consists of internal protonephridial tubules. We find that these assemble into complex branching patterns with a stereotyped succession of cell types along their length. Organ regeneration is likely to originate from a precursor structure arising in the blastema, which undergoes extensive branching morphogenesis. In an RNAi screen of signaling molecules, we identified an EGF receptor (Smed-EGFR-5) as a crucial regulator of branching morphogenesis and maintenance. Overall, our characterization of the planarian protonephridial system establishes a new paradigm for regenerative organogenesis and provides a platform for exploring its functional and evolutionary homologies with vertebrate excretory systems. PMID:21828097

  19. Long Length Contaminated Equipment Retrieval System Receiver Trailer and Transport Trailer Operations and Maintenance Manual

    SciTech Connect

    DALE, R.N.

    2000-05-01

    A system to accommodate the removal of long-length contaminated equipment (LLCE) from Hanford underground radioactive waste storage tanks was designed, procured, and demonstrated, via a project activity during the 1990s. The system is the Long Length Contaminated Equipment Removal System (LLCERS). LLCERS will be maintained and operated by Tank Farms Engineering and Operations organizations and other varied projects having a need for the system. The responsibility for the operation and maintenance of the LLCERS Receiver Trailer (RT) and Transport Trailer (TT) resides with the RPP Characterization Project Operations organization. The purpose of this document is to provide vendor supplied operating and maintenance (O & M) information for the RT and TT in a readily retrievable form. This information is provided this way instead of in a vendor information (VI) file to maintain configuration control of the operations baseline as described in RPP-6085, ''Configuration Management Plan for Long Length Contaminated Equipment Receiver and Transport Trailers''. Additional Operations Baseline documents are identified in RPP-6085.

  20. Light Vehicle Preventive Maintenance.

    ERIC Educational Resources Information Center

    Marine Corps Inst., Washington, DC.

    This correspondence course, originally developed for the Marine Corps, is designed to instruct students in the performance of preventive maintenance on motor vehicles. Instructional materials are presented in three chapters as follows: (1) Major Maintenance Areas (maintenance system, tires, batteries, cooling systems, and vehicle lubrication; (2)…

  1. DIG-1, a novel giant protein, non-autonomously mediates maintenance of nervous system architecture.

    PubMed

    Bénard, Claire Y; Boyanov, Alexander; Hall, David H; Hobert, Oliver

    2006-09-01

    Dedicated mechanisms exist to maintain the architecture of an animal's nervous system after development is completed. To date, three immunoglobulin superfamily members have been implicated in this process in the nematode Caenorhabditis elegans: the secreted two-Ig domain protein ZIG-4, the FGF receptor EGL-15 and the L1-like SAX-7 protein. These proteins provide crucial information for neuronal structures, such as axons, that allows them to maintain the precise position they acquired during development. Yet, how widespread this mechanism is throughout the nervous system, and what other types of factors underlie such a maintenance mechanism, remains poorly understood. Here, we describe a new maintenance gene, dig-1, that encodes a predicted giant secreted protein containing a large number of protein interaction domains. With 13,100 amino acids, the DIG-1 protein is the largest secreted protein identifiable in any genome database. dig-1 functions post-developmentally to maintain axons and cell bodies in place within axonal fascicles and ganglia. The failure to maintain axon and cell body position is accompanied by defects in basement membrane structure, as evidenced by electron microscopy analysis of dig-1 mutants. Expression pattern and mosaic analysis reveals that dig-1 is produced by muscles to maintain nervous system architecture, demonstrating that dig-1 functions non-autonomously to preserve the proper layout of neural structures. We propose that DIG-1 is a component of the basement membrane that mediates specific contacts between cellular surfaces and their environment through the interaction with a cell-type specific set of other maintenance factors. PMID:16887823

  2. Site handbook: data acquisition system information, passive solar retrofit Automobile Maintenance Facility, City of Philadelphia

    SciTech Connect

    Not Available

    1985-01-01

    Data were collected at the City of Philadelphia's Auto Maintenance Facility using an Aeoloan Kinetics PDL-24 data acquisition system. Instantaneous data readings were recorded each 15 seconds by the microprocessor. These channel readings were then averaged to produce hourly values which were then stored on an audio cassette. The energy saving strategies include: styrofoam and concrete roof coverings; weatherstripping; replacement of north windows with combination insulation and view glazing; PVC strips between heated and unheated areas; gas fired radiant heaters at individual work stations; reduction of the number of light fixtures; and the installation of retrofit window units for radiant solar heating, daylighting, ventilation, glare control and vandalism protection.

  3. Long-term maintenance of human induced pluripotent stem cells by automated cell culture system.

    PubMed

    Konagaya, Shuhei; Ando, Takeshi; Yamauchi, Toshiaki; Suemori, Hirofumi; Iwata, Hiroo

    2015-01-01

    Pluripotent stem cells, such as embryonic stem cells and induced pluripotent stem (iPS) cells, are regarded as new sources for cell replacement therapy. These cells can unlimitedly expand under undifferentiated conditions and be differentiated into multiple cell types. Automated culture systems enable the large-scale production of cells. In addition to reducing the time and effort of researchers, an automated culture system improves the reproducibility of cell cultures. In the present study, we newly designed a fully automated cell culture system for human iPS maintenance. Using an automated culture system, hiPS cells maintained their undifferentiated state for 60 days. Automatically prepared hiPS cells had a potency of differentiation into three germ layer cells including dopaminergic neurons and pancreatic cells. PMID:26573336

  4. Object oriented Simulation of Maintenance and Operations for Space Systems (OSMOSSYS)

    NASA Technical Reports Server (NTRS)

    Doran, Linda; Nguyen, Vien; Nguyen, Judy; Blumentritt, Will

    1993-01-01

    This paper describes the NASA/JSC Research Technology Opportunity Program (RTOP) activity to assess the supportability of space systems throughout their life cycles. Supportability analyses for space systems present unique attributes and problems. The OSMOSSYS (Object oriented Simulation of Maintenance and Operations for Space Systems) was developed using object-oriented design concepts to provide NASA an analysis tool which addresses the question `Will a proposed space facility be able to successfully perform the missions for which it is designed?' This model integrates the complete configuration of the system including the reliability and maintainability characteristics of each component, the logistics support, and the mission operations of the facility to assess the success rate of the planned mission(s). Two parallel design processes are being utilized; developing core modules utilizing C++, and incorporating as much code and ideas as possible from existing NASA models. The space station was used as a test case to demonstrate the applicability of the model.

  5. Attentional and non-attentional systems in the maintenance of verbal information in working memory: the executive and phonological loops

    PubMed Central

    Camos, Valérie; Barrouillet, Pierre

    2014-01-01

    Working memory is the structure devoted to the maintenance of information at short term during concurrent processing activities. In this respect, the question regarding the nature of the mechanisms and systems fulfilling this maintenance function is of particular importance and has received various responses in the recent past. In the time-based resource-sharing (TBRS) model, we suggest that only two systems sustain the maintenance of information at the short term, counteracting the deleterious effect of temporal decay and interference. A non-attentional mechanism of verbal rehearsal, similar to the one described by Baddeley in the phonological loop model, uses language processes to reactivate phonological memory traces. Besides this domain-specific mechanism, an executive loop allows the reconstruction of memory traces through an attention-based mechanism of refreshing. The present paper reviews evidence of the involvement of these two independent systems in the maintenance of verbal memory items. PMID:25426049

  6. Integrated crystal mounting and alignment system for high-throughput biological crystallography

    DOEpatents

    Nordmeyer, Robert A.; Snell, Gyorgy P.; Cornell, Earl W.; Kolbe, William F.; Yegian, Derek T.; Earnest, Thomas N.; Jaklevich, Joseph M.; Cork, Carl W.; Santarsiero, Bernard D.; Stevens, Raymond C.

    2007-09-25

    A method and apparatus for the transportation, remote and unattended mounting, and visual alignment and monitoring of protein crystals for synchrotron generated x-ray diffraction analysis. The protein samples are maintained at liquid nitrogen temperatures at all times: during shipment, before mounting, mounting, alignment, data acquisition and following removal. The samples must additionally be stably aligned to within a few microns at a point in space. The ability to accurately perform these tasks remotely and automatically leads to a significant increase in sample throughput and reliability for high-volume protein characterization efforts. Since the protein samples are placed in a shipping-compatible layered stack of sample cassettes each holding many samples, a large number of samples can be shipped in a single cryogenic shipping container.

  7. Integrated crystal mounting and alignment system for high-throughput biological crystallography

    DOEpatents

    Nordmeyer, Robert A.; Snell, Gyorgy P.; Cornell, Earl W.; Kolbe, William; Yegian, Derek; Earnest, Thomas N.; Jaklevic, Joseph M.; Cork, Carl W.; Santarsiero, Bernard D.; Stevens, Raymond C.

    2005-07-19

    A method and apparatus for the transportation, remote and unattended mounting, and visual alignment and monitoring of protein crystals for synchrotron generated x-ray diffraction analysis. The protein samples are maintained at liquid nitrogen temperatures at all times: during shipment, before mounting, mounting, alignment, data acquisition and following removal. The samples must additionally be stably aligned to within a few microns at a point in space. The ability to accurately perform these tasks remotely and automatically leads to a significant increase in sample throughput and reliability for high-volume protein characterization efforts. Since the protein samples are placed in a shipping-compatible layered stack of sample cassettes each holding many samples, a large number of samples can be shipped in a single cryogenic shipping container.

  8. Chip electrochromatographic systems: Novel vertically aligned carbon nanotube and silica monoliths based separations

    NASA Astrophysics Data System (ADS)

    Goswami, Shubhodeep

    2009-12-01

    Miniaturized chemical analysis systems, also know as 'lab-on-a-chip' devices have been rapidly developing over the last decade. Capillary electrochromatography (CEC), a multidimensional separation technique combining capillary electrophoresis (CE) and liquid chromatography (LC) has been of great interest for chip based applications. Preliminary work has been undertaken to develop vertically aligned carbon nanotubes and photopolymerizable silica solgel as novel stationary phase materials for 'chip CEC' separations. Patterned growth of CNTs in a specific location of the channel has been carried out using a solid phase Fe-Al catalyst as well as a vapor deposited ferrocene catalyst. Characterization of the CNT "forests" was achieved using optical microscopy, secondary electron microscopy, high resolution tunneling electron microscopy and Raman spectroscopy. Proof-of-concept applications were demonstrated using reversed phase CEC separations as well as solid phase extraction of a glycosylated protein using concanavilin A immobilized onto the CNT bed. Photopolymerizable silica solgel materials were developed as stationary phase for microfluidic electrochromatographic separations in disposable polydimethylsiloxane (PDMS) chip devices. Effect on morphology and pore size of gels were studied as function of UV and solgel polymerization conditions, porogen, salt additives, geometry and hydrolyzable methoxy-ies. Structural morphologies were studied with Secondary Electron Microscopy (SEM). Pore size and pore volumes were characterized by thermal porometry, nitrogen BET adsorptions and differential scanning calorimetry. Computational fluid dynamics and confocal microscopy tools were employed to study the transport of fluids and model analytes. These investigations were directed towards evolving improved strategies for rinsing of uncrosslinked monomers to form porous monoliths as well as to effect a desired separation under a set of electrochromatograhic conditions

  9. The Maintenance Of 3-D Scene Databases Using The Analytical Imagery Matching System (Aims)

    NASA Astrophysics Data System (ADS)

    Hovey, Stanford T.

    1987-06-01

    The increased demand for multi-resolution displays of simulated scene data for aircraft training or mission planning has led to a need for digital databases of 3-dimensional topography and geographically positioned objects. This data needs to be at varying resolutions or levels of detail as well as be positionally accurate to satisfy close-up and long distance scene views. The generation and maintenance processes for this type of digital database requires that relative and absolute spatial positions of geographic and cultural features be carefully controlled in order for the scenes to be representative and useful for simulation applications. Autometric, Incorporated has designed a modular Analytical Image Matching System (AIMS) which allows digital 3-D terrain feature data to be derived from cartographic and imagery sources by a combination of automatic and man-machine techniques. This system provides a means for superimposing the scenes of feature information in 3-D over imagery for updating. It also allows for real-time operator interaction between a monoscopic digital imagery display, a digital map display, a stereoscopic digital imagery display and automatically detected feature changes for transferring 3-D data from one coordinate system's frame of reference to another for updating the scene simulation database. It is an advanced, state-of-the-art means for implementing a modular, 3-D scene database maintenance capability, where original digital or converted-to-digital analog source imagery is used as a basic input to perform accurate updating.

  10. Road Maintenance Experience Using Polyurethane (PU) Foam Injection System and Geocrete Soil Stabilization as Ground Rehabilitation

    NASA Astrophysics Data System (ADS)

    Fakhar, A. M. M.; Asmaniza, A.

    2016-07-01

    There are many types of ground rehabilation and improvement that can be consider and implement in engineering construction works for soil improvement in order to prevent road profile deformation in later stage. However, when comes to road maintenance especially on operated expressways, not all method can be apply directly as it must comply to opreation's working window and lane closure basis. Key factors that considering ideal proposal for ground rehabilitation are time, cost, quality and most importantly practicality. It should provide long lifespan structure in order to reduce continuous cycle of maintenance. Thus, this paper will present two approaches for ground rehabilitation, namely Polyurethane (PU) Foam Injection System and Geocrete Soil Stabilization. The first approach is an injection system which consists two-parts chemical grout of Isocynate and Polyol when mixed together within soil structure through injection will polymerized with volume expansion. The strong expansion of grouting causes significant compression and compacting of the surrounding soil and subsequently improve ground properties and uplift sunken structure. The later is a cold in-place recyclying whereby mixture process that combines in-situ soil materials, cement, white powder (alkaline) additive and water to produce hard yet flexible and durable ground layer that act as solid foundation with improved bearing capacity. The improvement of the mechanical behaviour of soil through these two systems is investigated by an extensive testing programme which includes in-situ and laboratory test in determining properties such as strength, stiffness, compressibility, bearing capacity, differential settlement and etc.

  11. Infrared thermography of fan and compressor systems in a predictive maintenance program

    NASA Astrophysics Data System (ADS)

    Wurzbach, Richard N.

    1998-03-01

    Predictive Maintenance programs have been shown to be an effective and efficient approach to managing facilities maintenance. Cost savings through the reduction of time- based preventive tasks, and the reduction of unanticipated failures can be significant. Several inspection techniques have become standard, and are applicable to a broad range of equipment types and inspection scenarios. IR thermography of fan and compressor equipment presents a significant opportunity for cost saving applications in may facilities. Ventilation systems supply air to and remove air from working spaces, and mitigate environmental conditions for a number or purposes. Removal of hazardous pairs or gases, positive pressure atmosphere, or negative pressure atmosphere are a few examples. Vaneaxial fans are a common equipment type used to achieve this purpose. Both direct drive and belt driven fans are common for these systems. Belt drives present some unique imaging applications, where sheave and belt surface scan be observed. Compressor equipment has normally high operating temperatures, relative to other rotating equipment. The compression of gases is exothermic, and as a result, most compressors rely on an integral cooling process to function properly. Uniformity of temperature distribution on equipment surfaces, function of cooling systems, and verification of proper operation of loading and relief valves provide an overall illustration of equipment health.

  12. PROMUSE: a system for multi-media data presentation of protein structural alignments.

    PubMed

    Hansen, M D; Charp, E; Lodha, S; Meads, D; Pang, A

    1999-01-01

    We present and evaluate PROMUSE: an integrated visualization/sonification system for analyzing pairwise protein structural alignments (superpositions of two protein structures in three-dimensional space). We also explore how the use of sound can enhance the perception and recognition of specific aspects of the local environment at given positions in the represented molecular structure. Sonification presents several opportunities to researchers. For those with visual impairment, data sonification can be a useful alternative to visualization. Sonification can further serve to improve understanding of information in several ways. One use for data sonification is in tasks such as background monitoring, in which case sounds can be used to indicate thresholding events. With PROMUSE, data represented visually may be enhanced or disambiguated by adding sound to the presentation. This aspect of data representation is particularly important for showing features that are difficult to represent visually, due to occlusion or other factors. Another feature of our system is that by representing some variables through sound and others visually, the amount of information that may be represented simultaneously is extended. Our tool aims to augment the power of data visualization rather than replace it. To maximize the utility of our sonifications to represent data, we employed musical voices and melodic components with unique characteristics. We also used sound effects such as panning a voice to the left or right speaker and changing its volume to maximize the individuality of the sonification elements. By making the sonification parameters distinct, we allow the user to focus on those portions of the sonification necessary to resolve possible ambiguities in the visual display. Sonifications of low level data such as raw protein or DNA sequences tend to sound random, and not very musical. We chose instead to sonify an analysis of data features, and thereby present a higher level

  13. An intelligent systems approach for on-line power plant efficiency, emisions, and maintenance diagnostics

    SciTech Connect

    Hunt, M.; Williams, S.; Hickok, K.

    1995-06-01

    The Fossil Thermal performance Advisor{sup TM} (FTPA{sup TM}), developed by New York State Electric & Gas Corporation (NYSEG) and personnel from DHR Technologies, Inc. (DHR), is an advanced, on-line Electronic Performance Support System (EPSS) that helps fossil power plant operators, performance engineers, and plant managers improve daily plant operations. The FTPA uses an intelligent systems approach to identify existing and potential heat rate, emissions, and maintenance-related problems early, and to provide recommendations to help plant staff reduce costs related to these problems. The FTPA has been installed in several plants throughout the United States and abroad, most recently at NYSEG`s Greenridge Station, Unit No. 4. Currently, another system is being installed at Portland General Electric`s Boardman Station. This paper examines advances in the FTPA architecture designed to significantly reduce installation costs while increasing the benefits provided by the FTPA for smaller pulverized coal units, such as Greenidge Unit No. 4.

  14. Reliable Alignment in Total Knee Arthroplasty by the Use of an iPod-Based Navigation System

    PubMed Central

    Koenen, Paola; Schneider, Marco M.; Fröhlich, Matthias; Driessen, Arne; Bouillon, Bertil; Bäthis, Holger

    2016-01-01

    Axial alignment is one of the main objectives in total knee arthroplasty (TKA). Computer-assisted surgery (CAS) is more accurate regarding limb alignment reconstruction compared to the conventional technique. The aim of this study was to analyse the precision of the innovative navigation system DASH® by Brainlab and to evaluate the reliability of intraoperatively acquired data. A retrospective analysis of 40 patients was performed, who underwent CAS TKA using the iPod-based navigation system DASH. Pre- and postoperative axial alignment were measured on standardized radiographs by two independent observers. These data were compared with the navigation data. Furthermore, interobserver reliability was measured. The duration of surgery was monitored. The mean difference between the preoperative mechanical axis by X-ray and the first intraoperatively measured limb axis by the navigation system was 2.4°. The postoperative X-rays showed a mean difference of 1.3° compared to the final navigation measurement. According to radiographic measurements, 88% of arthroplasties had a postoperative limb axis within ±3°. The mean additional time needed for navigation was 5 minutes. We could prove very good precision for the DASH system, which is comparable to established navigation devices with only negligible expenditure of time compared to conventional TKA. PMID:27313898

  15. Self-propelled in-tube shuttle and control system for automated measurements of magnetic field alignment

    SciTech Connect

    Boroski, W.N.; Nicol, T.H. ); Pidcoe, S.V. . Space Systems Div.); Zink, R.A. )

    1990-03-01

    A magnetic field alignment gauge is used to measure the field angle as a function of axial position in each of the magnets for the Superconducting Super Collider (SSC). Present measurements are made by manually pushing the through the magnet bore tube and stopping at intervals to record field measurements. Gauge location is controlled through graduation marks and alignment pins on the push rods. Field measurements are recorded on a logging multimeter with tape output. Described is a computerized control system being developed to replace the manual procedure for field alignment measurements. The automated system employs a pneumatic walking device to move the measurement gauge through the bore tube. Movement of the device, called the Self-Propelled In-Tube Shuttle (SPITS), is accomplished through an integral, gas driven, double-acting cylinder. The motion of the SPITS is transferred to the bore tube by means of a pair of controlled, retractable support feet. Control of the SPITS is accomplished through an RS-422 interface from an IBM-compatible computer to a series of solenoid-actuated air valves. Direction of SPITS travel is determined by the air-valve sequence, and is managed through the control software. Precise axial position of the gauge within the magnet is returned to the control system through an optically-encoded digital position transducer attached to the shuttle. Discussed is the performance of the transport device and control system during preliminary testing of the first prototype shuttle. 1 ref., 7 figs.

  16. Self-propelled in-tube shuttle and control system for automated measurements of magnetic field alignment

    NASA Astrophysics Data System (ADS)

    Boroski, W. N.; Nicol, T. H.; Pidcoe, S. V.; Zink, R. A.

    1990-03-01

    A magnetic field alignment gauge is used to measure the field angle as a function of axial position in each of the magnets for the Superconducting Super Collider (SSC). Present measurements are made by manually pushing the gauge through the magnet bore tube and stopping at intervals to record field measurements. Gauge location is controlled through graduation marks and alignment pins on the push rods. Field measurements are recorded on a logging multimeter with tape output. Described is a computerized control system being developed to replace the manual procedure for field alignment measurements. The automated system employs a pneumatic walking device to move the measurement gauge through the bore tube. Movement of the device, called the Self-Propelled In-Tube Shuttle (SPITS), is accomplished through an integral, gas driven, double-acting cylinder. The motion of the SPITS is transferred to the bore tube by means of a pair of controlled, retractable support feet. Control of the SPITS is accomplished through an RS-422 interface from an IBM-compatible computer to a series of solenoid-actuated air valves. Direction of SPITS travel is determined by the air-valve sequence, and is managed through the control software. Precise axial position of the gauge within the magnet is returned to the control system through an optically-encoded digital position transducer attached to the shuttle. Discussed is the performance of the transport device and control system during preliminary testing of the first prototype shuttle.

  17. Study of the operation and maintenance of computer systems to meet the requirements of 10 CFR 73. 55

    SciTech Connect

    Lewis, J.R.; Byers, K.R.; Fluckiger, J.D.; McBride, K.C.

    1986-01-01

    The Pacific Northwest Laboratory has studied the operation and maintenance of computer-managed systems that can help nuclear power plant licensees to meet the physical security requirements of 10 CFR 73.55 (for access control, alarm monitoring, and alarm recording). This report of that study describes a computer system quality assurance program that is based on a system of related internal controls. A discussion of computer system evaluation includes verification and validation mechanisms for assuring that requirements are stated and that the product fulfills these requirements. Finally, the report describes operator and security awareness training and a computer system preventive maintenance program. 24 refs.

  18. Preventive maintenance system for the photomultiplier detector blocks of PET scanners

    DOEpatents

    Levy, A.V.; Warner, D.

    1995-01-24

    A system including a method and apparatus for preventive maintenance of PET scanner photomultiplier detector blocks is disclosed. The qualitative comparisons used in the method of the present invention to provide an indication in the form of a display or printout advising the user that the photomultiplier block is stable, intermittently unstable, or drifting unstable, and also advising of the expected date of failure of a photomultiplier block in the PET scanner. The system alerts the user to replace the defective photomultiplier block prior to catastrophic failure in a scheduled preventative maintenance program, thus eliminating expensive and unscheduled downtime of the PET scanner due to photomultiplier failure. The apparatus for carrying out the method of the present invention preferably resides in the host computer controlling a PET scanner. It includes a memory adapted for storing a record of a number of iterative adjustments that are necessary to calibrate the gain of a photomultiplier detector block i at a time t[sub 0], a time t[sub 1] and a time T, where T>t[sub 1]>t[sub 0], which is designated as Histo(i,j(t)). The apparatus also includes a processor configured by a software program or a combination of programmed RAM and ROM devices to perform a number of calculations and operations on these values, and also includes a counter for analyzing each photomultiplier detector block i=1 through I of a PET scanner. 40 figures.

  19. Preventive maintenance system for the photomultiplier detector blocks of pet scanners

    DOEpatents

    Levy, Alejandro V.; Warner, Donald

    1995-01-24

    A system including a method and apparatus for preventive maintenance of PET scanner photomultiplier detector blocks is disclosed. The quantitive comparisons used in the method of the present invention to provide an indication in the form of a display or printout advising the user that the photomultiplier block is stable, intermittently unstable, or drifting unstable, and also advising of the expected date of failure of a photomultiplier block in the PET scanner. The system alerts the user to replace the defective photomultiplier block prior to catastrophic failure in a scheduled preventative maintenance program, thus eliminating expensive and unscheduled downtime of the PET scanner due to photomultiplier failure. The apparatus for carrying out the method of the present invention preferably resides in the host computer controlling a PET scanner. It includes a memory adapted for storing a record of a number of iterative adjustments that are necessary to calibrate the gain of a photomultiplier detector block i at a time t.sub.0, a time t.sub.1 and a time T, where T>t.sub.1 >t.sub.0, which is designated as Histo(i,j(t)). The apparatus also includes a processor configured by a software program or a combination of programmed RAM and ROM devices to perform a number of calculations and operations on these values, and also includes a counter for analyzing each photomultiplier detector block i=1 through I of a PET scanner.

  20. Complementary characterization data in support of uniaxially aligned electrospun nanocomposites based on a model PVOH-epoxy system.

    PubMed

    Karimi, Samaneh; Staiger, Mark P; Buunk, Neil; Fessard, Alison; Tucker, Nick

    2016-06-01

    This paper presents complementary data corresponding to characterization tests done for our research article entitled "Uniaxially aligned electrospun fibers for advanced nanocomposites based on a model PVOH-epoxy system" (Karimi et al., 2016) [1]. Poly(vinyl alcohol) and epoxy resin were selected as a model system and the effect of electrospun fiber loading on polymer properties was examined in conjunction with two manufacturing methods. A novel electrospinning technology for production of uniaxially aligned nanofiber arrays was used. A conventional wet lay-up fabrication method is compared against a novel, hybrid electrospinning-electrospraying approach. The structure and thermomechanical properties of resulting composite materials were examined using scanning electron microscopy, dynamic mechanical analysis, thermogravimetric analysis, differential scanning calorimetry, Fourier transform infrared spectroscopy, and tensile testing. For discussion of obtained results please refer to the research paper (Karimi et al., 2016) [1]. PMID:26977430

  1. Assessment of remote maintenance technologies and their potential application in the Federal Waste Management System (FWMS)

    SciTech Connect

    Kring, C.T.; Meacham, S.A.; Peishel, F.L.

    1988-10-01

    The 40 plus years of remote operating experience in nuclear facilities are summarized, with emphasis on the evolution and capabilities of the remote systems. Current commercially available systems and major development activities are described. The advanced servomanipulator is described, which represents new remote technology that has been developed for the Department of Energy-Nuclear Energy and that can significantly improve remote operations by extending the range of admissible remote tasks and increasing remote work efficiency. Also based upon past ORNL experience with remote facilities for reprocessing fuel, the guidelines and concepts that are utilized in the design, fabrication, and remote operation of mechanical process equipment and facilities are outlined. The currently available remote handling systems that can be applied, in various combinations, to large-volume in-cell operations are described, and requirements for waste storage facilities are reviewed. A basic trade-off analysis of these remote systems considering waste plant requirements is given. Justification is given for selecting the overhead crane/servomanipulator-based maintenance concept as the option most desirable for future waste processing plant in-cell maintenance. The Robotics/Remote Handling workshop that was implemented by the Office of Storage and Transportation System during the period that this assessment was being performed, helped focus the remaining time allocated to this effort on the future implementation of an overall program plan using a total systems approach. The concluding recommendation of this assessment is that this Robotics/Remote Handling program plan be developed and implemented as soon as possible. 43 refs., 17 figs., 9 tabs.

  2. Inconsistencies between navigation data and radiographs in total knee arthroplasty are system-dependent and affect coronal alignment

    PubMed Central

    Carli, Alberto; Aoude, Ahmed; Reuven, Avishai; Matache, Bogdan; Antoniou, John; Zukor, David J.

    2014-01-01

    Background Few studies have compared the effect of different computer navigation systems on postoperative alignment in patients who have had total knee arthroplasty (TKA). We examined 2 computed tomography (CT)–free computer navigation systems by comparing the accuracy of intraoperative measurements to postoperative alignment. Methods Patients underwent unilateral TKA performed by a single surgeon using 1 of 2 CT-free navigation systems. We compared final intraoperative tibial and femoral coronal angles and mechanical axis with the same angles measured on standing postoperative radiographs. Results Groups of 31 and 50 patients underwent TKA with the 2 systems, respectively. We noted a significant difference in the coronal tibial implant angle (1.29º ± 1.35º) and in the mechanical axis (1.59º ± 2.36º) for one navigation system (both p < 0.001), while only the coronal tibial implant angle showed a significant difference (1.17º ± 1.65º, p < 0.001) for the second system. The number of radiographic outliers also significantly differed. A significantly higher proportion (32%; p < 0.01) of patients in the second cohort exhibited unacceptable malalignment compared with the first cohort (24%). Conclusion Navigation systems for TKA continue to increase in sophistication and popularity. Owing to the significant difference in the proportion of alignment outliers in the 2 navigation systems tested in this study, orthopedic surgeons should not consider all TKA navigation systems equivalent. Additional investigations are needed to compare the accuracy of a variety of CT-free and CT-based navigation systems and to confirm our finding that accuracy is system-dependent. PMID:25265103

  3. Using a co-ordinate measuring machine to align multiple element large optical systems

    NASA Astrophysics Data System (ADS)

    Howick, Eleanor F.; Cochrane, David; Meier, David

    2007-09-01

    A high precision Co-ordinate Measuring Machine (CMM) is an ideal instrument for aligning mid to large (400 to 600 mm) diameter multiple element lens assemblies. The CMM has many advantages over simpler dial gauge and rotary table setups. For example, these traditional methods do not necessarily make it easy to separate the out-of-roundness of a lens or its mounting cell, from a misalignment of the lens and cell. With a CMM, the 'as made' geometry of both the lenses and their mounting cells can be determined before the mounting and alignment process begins. By considering the actual shape of the lenses and cells, adjustments can be made during the alignment process to ensure that the complete assembly meets the designer's tolerances. This paper discusses CMM alignment techniques used and experience gained while assembling large lens corrector assemblies (for example, the three element Prime Focus Unit for FMOS, the Subaru Fibre Multi-Object Spectrograph) destined for installation in astronomical telescopes.

  4. Beam-based alignment and tuning procedures for e sup + e sup minus collider final focus systems

    SciTech Connect

    Bulos, F.; Burke, D.; Helm, R.; Irwin, J.; Odian, A.; Roy, G.; Ruth, R.; Yamamoto, N.

    1991-05-01

    For future linear colliders, with very small emittances and beam sizes and demanding tolerances on final focus system alignment and magnet errors, it becomes increasingly important to use the beam as a diagnostic tool. We report here procedures we have identified and will be implemented in the Final Focus Test Beam at SLAC incorporating (1) quadrupole strength changes, (2) central orbit modifications, (3) spot size measurements, and (4) beam stability monitoring. 3 refs., 4 figs., 3 tabs.

  5. Scaling up logic-based truth maintenance systems via fact garbage collection

    SciTech Connect

    Everett, J.O.; Forbus, K.D.

    1996-12-31

    Truth maintenance systems provide caches of beliefs and inferences that support explanations and search. Traditionally, the cost of using a TMS is monotonic growth in the size of this cache. In some applications this cost is too high; for example, intelligent learning environments may require students to explore many alternatives, which leads to unacceptable performance. This paper describes an algorithm for fact garbage collection that retains the explanation-generating capabilities of a TMS while eliminating the increased storage overhead. We describe the application context that motivated this work and the properties of applications that benefit from this technique. We present the algorithm, showing how to balance the tradeoff between maintaining a useful cache and reclaiming storage, and analyze its complexity. We demonstrate that this algorithm can eliminate monotonic storage growth, thus making it more practical to field large-scale TMS-based systems.

  6. Fault-tolerant system analysis: imperfect switching and maintenance. Final technical paper

    SciTech Connect

    Veatch, M.H.; Foley, R.D.

    1987-01-01

    This final report presents the results of research into two important areas of concern for fault-tolerant avionics systems: testability analysis and innovative repair policies. The algorithms developed from this research have been included in the Mission Reliability Model (MIREM) and verified by comparison with known results from several Integrated Communication, Navigation, and Identification Avionics architectures. The purpose of the testability analysis was to develop techniques for assessing the impact of imperfect switching on the overall reliability of fault-tolerant avionics. A method of quantifying the effects of undetected errors and false alarms has been developed and included in MIREM. Under the next phase of the program, three repair statistics were identified: Mean Time To Repair, Mean Time Between Maintenance Actions, and Inherent Availability. These were used to define four alternative repair policies: immediate repair, deferred repair, scheduled maintenance, and repair at degraded level. Also included in MIREM as model outputs, these four options offer greater flexibility in evaluating and developing avionics designs.

  7. Mating system contributes only slightly to female maintenance in gynodioecious Geranium maculatum (Geraniaceae)

    PubMed Central

    Van Etten, M L; Deen, A C; Hamrick, J L; Chang, S-M

    2014-01-01

    Gynodioecy, the co-occurrence of female and hermaphroditic individuals within a population, is an important intermediate in the evolution of separate sexes. The first step, female maintenance, requires females to have higher seed fitness compared with hermaphrodites. A common mechanism thought to increase relative female fitness is inbreeding depression avoidance, the magnitude of which depends on hermaphroditic selfing rates and the strength of inbreeding depression. Less well studied is the effect of biparental inbreeding on female fitness. Biparental inbreeding can affect relative female fitness only if its consequence or frequency differs between sexes, which could occur if sex structure and genetic structure both occur within populations. To determine whether inbreeding avoidance and/or biparental inbreeding can account for female persistence in Geranium maculatum, we measured selfing and biparental inbreeding rates in four populations and the spatial genetic structure in six populations. Selfing rates of hermaphrodites were low and did not differ significantly from zero in any population, leading to females gaining at most a 1–14% increase in seed fitness from inbreeding avoidance. Additionally, although significant spatial genetic structure was found in all populations, biparental inbreeding rates were low and only differed between sexes in one population, thereby having little influence on female fitness. A review of the literature revealed few sexual differences in biparental inbreeding among other gynodioecious species. Our results show that mating system differences may not fully account for female maintenance in this species, suggesting other mechanisms may be involved. PMID:24824284

  8. A system for the calculation and visualisation of radiation field for maintenance support in nuclear power plants.

    PubMed

    Ohga, Yukiharu; Fukuda, Mitsuko; Shibata, Kiyotaka; Kawakami, Takashi; Matsuzaki, Tomokazu

    2005-01-01

    A system has been developed to improve the efficiency of maintenance work while decreasing the radiation exposure of maintenance personnel in nuclear power plants. The input data for dose rate calculation are automatically generated by using computer-aided design data. Changes for the input data corresponding to the progress of maintenance work, such as installation of a radiation shield and removal of a component, are easily input interactively on a graphical user interface (GUI). A new method was proposed which searches the sets of source and detector points between which gamma-ray attenuation is changed by the component movement. The calculation is performed only for the changed sets, so that the change of the three-dimensional dose rate distribution is calculated rapidly according to the work progress. The dose rate distribution and the radiation exposure of maintenance personnel are displayed three-dimensionally in colour with plant components and pipes on the GUI. PMID:16604706

  9. Complementary characterization data in support of uniaxially aligned electrospun nanocomposites based on a model PVOH-epoxy system

    PubMed Central

    Karimi, Samaneh; Staiger, Mark P.; Buunk, Neil; Fessard, Alison; Tucker, Nick

    2016-01-01

    This paper presents complementary data corresponding to characterization tests done for our research article entitled “Uniaxially aligned electrospun fibers for advanced nanocomposites based on a model PVOH-epoxy system” (Karimi et al., 2016) [1]. Poly(vinyl alcohol) and epoxy resin were selected as a model system and the effect of electrospun fiber loading on polymer properties was examined in conjunction with two manufacturing methods. A novel electrospinning technology for production of uniaxially aligned nanofiber arrays was used. A conventional wet lay-up fabrication method is compared against a novel, hybrid electrospinning–electrospraying approach. The structure and thermomechanical properties of resulting composite materials were examined using scanning electron microscopy, dynamic mechanical analysis, thermogravimetric analysis, differential scanning calorimetry, Fourier transform infrared spectroscopy, and tensile testing. For discussion of obtained results please refer to the research paper (Karimi et al., 2016) [1]. PMID:26977430

  10. Highly ordered and highly aligned two-dimensional binary superlattice of a SWNT/cylindrical-micellar system.

    PubMed

    Lim, Sung-Hwan; Jang, Hyung-Sik; Ha, Jae-Min; Kim, Tae-Hwan; Kwasniewski, Pawel; Narayanan, Theyencheri; Jin, Kyeong Sik; Choi, Sung-Min

    2014-11-10

    We report a highly ordered intercalated hexagonal binary superlattice of hydrophilically functionalized single-walled carbon nanotubes (p-SWNTs) and surfactant (C12 E5 ) cylindrical micelles. When p-SWNTs (with a diameter slightly larger than that of the C12 E5 cylinders) were added to the hexagonally packed C12 E5 cylindrical-micellar system, p-SWNTs positioned themselves in such a way that the free-volume entropies for both p-SWNTs and C12 E5 cylinders were maximized, thus resulting in the intercalated hexagonal binary superlattice. In this binary superlattice, a hexagonal array of p-SWNTs is embedded in a honeycomb lattice of C12 E5 cylinders. The intercalated hexagonal binary superlattice can be highly aligned in one direction by an oscillatory shear field and remains aligned after the shear is removed. PMID:25244635

  11. Method of Deployment of a Space Tethered System Aligned to the Local Vertical

    NASA Astrophysics Data System (ADS)

    Zakrzhevskii, A. E.

    2016-09-01

    The object of this research is a space tether of two bodies connected by a flexible massless string. The research objective is the development and theoretical justification of a novel approach to the solution of the problem of deployment of the space tether in a circular orbit with its alignment to the local vertical. The approach is based on use of the theorem on the angular momentum change. It allows developing the open-loop control of the tether length that provides desired change of the angular momentum of the tether under the effect of the gravitational torque to the value, which corresponds to the angular momentum of the deployed tether aligned to the local vertical. The given example of application of the approach to a case of deployment of a tether demonstrates the simplicity of use of the method in practice, and also the method of validation of the mathematical model.

  12. Method of Deployment of a Space Tethered System Aligned to the Local Vertical

    NASA Astrophysics Data System (ADS)

    Zakrzhevskii, A. E.

    2016-04-01

    The object of this research is a space tether of two bodies connected by a flexible massless string. The research objective is the development and theoretical justification of a novel approach to the solution of the problem of deployment of the space tether in a circular orbit with its alignment to the local vertical. The approach is based on use of the theorem on the angular momentum change. It allows developing the open-loop control of the tether length that provides desired change of the angular momentum of the tether under the effect of the gravitational torque to the value, which corresponds to the angular momentum of the deployed tether aligned to the local vertical. The given example of application of the approach to a case of deployment of a tether demonstrates the simplicity of use of the method in practice, and also the method of validation of the mathematical model.

  13. Facilities maintenance handbook

    NASA Technical Reports Server (NTRS)

    1991-01-01

    This handbook is a guide for facilities maintenance managers. Its objective is to set minimum facilities maintenance standards. It also provides recommendations on how to meet the standards to ensure that NASA maintains its facilities in a manner that protects and preserves its investment in the facilities in a cost-effective manner while safely and efficiently performing its mission. This handbook implements NMI 8831.1, which states NASA facilities maintenance policy and assigns organizational responsibilities for the management of facilities maintenance activities on all properties under NASA jurisdiction. It is a reference for facilities maintenance managers, not a step-by-step procedural manual. Because of the differences in NASA Field Installation organizations, this handbook does not assume or recommend a typical facilities maintenance organization. Instead, it uses a systems approach to describe the functions that should be included in any facilities maintenance management system, regardless of its organizational structure. For documents referenced in the handbook, the most recent version of the documents is applicable. This handbook is divided into three parts: Part 1 specifies common definitions and facilities maintenance requirements and amplifies the policy requirements contained in NMI 8831. 1; Part 2 provides guidance on how to meet the requirements of Part 1, containing recommendations only; Part 3 contains general facilities maintenance information. One objective of this handbook is to fix commonality of facilities maintenance definitions among the Centers. This will permit the application of uniform measures of facilities conditions, of the relationship between current replacement value and maintenance resources required, and of the backlog of deferred facilities maintenance. The utilization of facilities maintenance system functions will allow the Centers to quantitatively define maintenance objectives in common terms, prepare work plans, and

  14. A preventive maintenance policy for a standby system subject to internal failures and external shocks with loss of units

    NASA Astrophysics Data System (ADS)

    Eloy Ruiz-Castro, Juan

    2015-07-01

    In many situations, serious damage and considerable financial losses are caused by non-repairable failures of a system. Redundant systems and maintenance policies are commonly employed to improve reliability. This paper is focused on the modelling of a complex cold standby system by analysing the effectiveness and costs of preventive maintenance, always in an algorithmic form. The online unit of the system is subject to wear failures and external shocks. The online unit can go through an indeterminate number of degradation levels before failure. This one is observed when inspections occur. Inspections are performed at random intervals, and when one takes place, the unit is taken to the preventive maintenance facility if it is necessary. The preventive maintenance time and cost is different depending on the degradation level observed. If only one unit is performing, a minimal maintenance policy is adopted in order to optimise system behaviour. Reliability measures such as the conditional probability of failure are worked out in a well-structured and algebraic form in transient and stationary regimes by using algorithmic methods. The stationary distribution is calculated using matrix analytic methods, and rewards are included in the model. An optimisation example shows the versatility of the model presented.

  15. Using Project Performance to Measure Effectiveness of Quality Management System Maintenance and Practices in Construction Industry

    PubMed Central

    Leong, Tiong Kung; Ariff, Mohd. Shoki Md.

    2014-01-01

    This paper proposed seven existing and new performance indicators to measure the effectiveness of quality management system (QMS) maintenance and practices in construction industry. This research is carried out with a questionnaire based on QMS variables which are extracted from literature review and project performance indicators which are established from project management's theory. Data collected was analyzed using correlation and regression analysis. The findings indicate that client satisfaction and time variance have positive and significant relationship with QMS while other project performance indicators do not show significant results. Further studies can use the same project performance indicators to study the effectiveness of QMS in different sampling area to improve the generalizability of the findings. PMID:24701182

  16. Using project performance to measure effectiveness of quality management system maintenance and practices in construction industry.

    PubMed

    Leong, Tiong Kung; Zakuan, Norhayati; Mat Saman, Muhamad Zameri; Ariff, Mohd Shoki Md; Tan, Choy Soon

    2014-01-01

    This paper proposed seven existing and new performance indicators to measure the effectiveness of quality management system (QMS) maintenance and practices in construction industry. This research is carried out with a questionnaire based on QMS variables which are extracted from literature review and project performance indicators which are established from project management's theory. Data collected was analyzed using correlation and regression analysis. The findings indicate that client satisfaction and time variance have positive and significant relationship with QMS while other project performance indicators do not show significant results. Further studies can use the same project performance indicators to study the effectiveness of QMS in different sampling area to improve the generalizability of the findings. PMID:24701182

  17. An application of oscillation damped motion for suspended payloads to the advanced integrated maintenance system

    SciTech Connect

    Noakes, M.W. ); Petterson, B.J.; Werner, J.C. )

    1990-01-01

    Transportation of objects using overhead cranes can induce pendulum motion of the object, which usually must be damped or allowed to decay before the next process can take place. Recent work at Sandia National Laboratories (SNL) has shown that oscillation damped transport and swing-free stops are possible by properly programming the acceleration of the transporting crane. This paper reviews the theory associated with oscillation-damped trajectories for simply suspended objects and describes a specific, full-scale implementation of the damped oscillation methods for the Oak Ridge National Laboratory (ORNL) Advanced Integrated Maintenance System (AIMS). Hardware and software requirements and constraints for proper operation are discussed. Finally, test results and lessons learned are presented. 5 refs., 4 figs.

  18. 40 CFR 52.2348 - National Highway Systems Designation Act Motor Vehicle Inspection and Maintenance (I/M) Programs.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 5 2014-07-01 2014-07-01 false National Highway Systems Designation... IMPLEMENTATION PLANS (CONTINUED) Utah § 52.2348 National Highway Systems Designation Act Motor Vehicle Inspection and Maintenance (I/M) Programs. (a) On March 15, 1996 the Governor of Utah submitted a revised...

  19. 40 CFR 52.2348 - National Highway Systems Designation Act Motor Vehicle Inspection and Maintenance (I/M) Programs.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 5 2013-07-01 2013-07-01 false National Highway Systems Designation... IMPLEMENTATION PLANS (CONTINUED) Utah § 52.2348 National Highway Systems Designation Act Motor Vehicle Inspection and Maintenance (I/M) Programs. (a) On March 15, 1996 the Governor of Utah submitted a revised...

  20. 40 CFR 52.2348 - National Highway Systems Designation Act Motor Vehicle Inspection and Maintenance (I/M) Programs.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 5 2012-07-01 2012-07-01 false National Highway Systems Designation... IMPLEMENTATION PLANS (CONTINUED) Utah § 52.2348 National Highway Systems Designation Act Motor Vehicle Inspection and Maintenance (I/M) Programs. (a) On March 15, 1996 the Governor of Utah submitted a revised...

  1. Field Evaluation of the Generalized Maintenance Trainer-Simulator: I. Fleet Communications System. ; Technical Report No. 89.

    ERIC Educational Resources Information Center

    Rigney, J. W.; And Others

    This report describes the Generalized Maintenance Trainer-Simulator (GMTS), an instructional system designed to give electronics students intensive troubleshooting practice in a simulated hands-on training environment, and reports on a field evaluation of the GMTS applied to systems level troubleshooting in radio communications. The GMTS can be…

  2. AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XXV, I--CATERPILLAR DIESEL ENGINE COOLING SYSTEM D-8 AND 824 MODELS, II--TIRES AND TIRE HARDWARE.

    ERIC Educational Resources Information Center

    Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF THE DIESEL ENGINE COOLING SYSTEM AND TO PROVIDE A DESCRIPTION OF HEAVY TIRES AND WHEELS USED ON DIESEL POWERED VEHICLES. TOPICS ARE (1) THEORY OF THE COOLING SYSTEM, (2) COOLING SYSTEM COMPONENTS, (3) MAINTENANCE TIPS (COOLING SYSTEM), (4)…

  3. AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XXIV, I--MAINTAINING THE FUEL SYSTEM PART III--CATERPILLAR DIESEL ENGINE, II--UNDERSTANDING THE VOLTAGE REGULATOR/ALTERNATOR.

    ERIC Educational Resources Information Center

    Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF THE DIESEL ENGINE FUEL AND BATTERY CHARGING SYSTEM. TOPICS ARE (1) INJECTION TIMING CONTROLS, (2) GOVERNOR, (3) FUEL SYSTEM MAINTENANCE TIPS, (4) THE CHARGING SYSTEM, (5) REGULATING THE GENERATOR/ALTERNATOR, AND (6) CHARGING SYSTEM SERVICE…

  4. Nuclear Systems Enhanced Performance Program, Maintenance Cycle Extension in Advanced Light Water Reactor Design

    SciTech Connect

    Professor Neill Todreas

    2001-10-01

    A renewed interest in new nuclear power generation in the US has spurred interest in developing advanced reactors with features which will address the public's concerns regarding nuclear generation. However, it is economic performance which will dictate whether any new orders for these plants will materialize. Economic performance is, to a great extent, improved by maximizing the time that the plant is on-line generating electricity relative to the time spent off-line conducting maintenance and refueling. Indeed, the strategy for the advanced light water reactor plant IRIS (International Reactor, Innovative and Secure) is to utilize an eight year operating cycle. This report describes a formalized strategy to address, during the design phase, the maintenance-related barriers to an extended operating cycle. The top-level objective of this investigation was to develop a methodology for injecting component and system maintainability issues into the reactor plant design process to overcome these barriers. A primary goal was to demonstrate the applicability and utility of the methodology in the context of the IRIS design. The first step in meeting the top-level objective was to determine the types of operating cycle length barriers that the IRIS design team is likely to face. Evaluation of previously identified regulatory and investment protection surveillance program barriers preventing a candidate operating PWR from achieving an extended (48 month) cycle was conducted in the context of the IRIS design. From this analysis, 54 known IRIS operating cycle length barriers were identified. The resolution methodology was applied to each of these barriers to generate design solution alternatives for consideration in the IRIS design. The methodology developed has been demonstrated to narrow the design space to feasible design solutions which enable a desired operating cycle length, yet is general enough to have broad applicability. Feedback from the IRIS design team indicates

  5. Alignment fixture

    DOEpatents

    Bell, Grover C.; Gibson, O. Theodore

    1980-01-01

    A part alignment fixture is provided which may be used for precise variable lateral and tilt alignment relative to the fixture base of various shaped parts. The fixture may be used as a part holder for machining or inspection of parts or alignment of parts during assembly and the like. The fixture includes a precisely machined diameter disc-shaped hub adapted to receive the part to be aligned. The hub is nested in a guide plate which is adapted to carry two oppositely disposed pairs of positioning wedges so that the wedges may be reciprocatively positioned by means of respective micrometer screws. The sloping faces of the wedges contact the hub at respective quadrants of the hub periphery. The lateral position of the hub relative to the guide plate is adjusted by positioning the wedges with the associated micrometer screws. The tilt of the part is adjusted relative to a base plate, to which the guide plate is pivotally connected by means of a holding plate. Two pairs of oppositely disposed wedges are mounted for reciprocative lateral positioning by means of separate micrometer screws between flanges of the guide plate and the base plate. Once the wedges are positioned to achieve the proper tilt of the part or hub on which the part is mounted relative to the base plate, the fixture may be bolted to a machining, inspection, or assembly device.

  6. Relationship between Pulsating Aurora and Small-scale Field-Aligned Current Systems

    NASA Astrophysics Data System (ADS)

    Gillies, D. M.; Knudsen, D. J.; Donovan, E.; Kabirzadeh, R.

    2014-12-01

    Field-aligned currents derived from CHAMP satellite overpasses were compared to THEMIS ground-based all-sky camera array. Two separate conjunctions were studied in detail. The primary focus of this study was to investigate FAC derived from magnetometer measurements obtained by CHAMP collocated with various auroral phenomena. Two types of aurora were studied in detail: pulsating aurora and diffuse aurora occurring equatorward ward of an established auroral arc. We found that pulsating aurora exhibited low levels of fluctuating field aligned currents alternating between +/- 1 μA/m2 for the duration of the conjunction. We found similar behaviour for diffuse aurora equatorward of stable auroral arc events. Upon entering the region of diffuse aurora CHAMP recorded an alternating current fluctuating between +/- 5 μA/m2. High resolution data confirmed this alternating current structure as well as the presence of small scale arc structure seen by larger, small time scale amplitude fluctuations similar to that seen in the auroral arcs. These results show that electrical currents in diffuse and pulsating auroral structures are relevant.

  7. Building blocks for actively-aligned micro-optical systems in rapid prototyping and small series production

    NASA Astrophysics Data System (ADS)

    Böttger, Gunnar; Queisser, Marco; Arndt-Staufenbiel, Norbert; Schröder, Henning; Lang, K.-D.

    2015-03-01

    In recent years there has been considerable progress in utilizing fully automated machines for the assembly of microoptical systems. Such systems integrate laser sources, optical elements and detectors into tight packages, and efficiently couple light to free space beams, waveguides in optical backplanes, or optical fibers for longer reach transmission. The required electrical-optical and optical components are placed and aligned actively in more than one respect. For one, all active components are actually operated in the alignment process, and, more importantly, the placing of all components is controlled actively by camera systems and power detectors with live feedback for an optimal coupling efficiency. The total number of optical components typically is in the range of 5 to 50, whereas the number of actors with gripping tools for the actual handling and aligning is limited, with little flexibility in the gripping width. The assembly process therefore is strictly sequential and, given that an automated tool changing has not been established in this class of machines yet, there are either limitations in the geometries of components that may be used, or time-consuming interaction by human operators is needed. As a solution we propose and present lasered glass building blocks with standardized gripping geometries that enclose optical elements of various shapes and functionalities. These are cut as free form geometries with green short pulse and CO2 lasers. What seems to add cost at first rather increases freedom of design and adds an economical flexibility to create very hybrid assemblies of various micro-optical assemblies also in small numbers.

  8. Antares alignment gimbal positioner

    SciTech Connect

    Day, R.D.; Viswanathan, V.K.; Saxman, A.C.; Lujan, R.E.; Woodfin, G.L.; Sweatt, W.C.

    1981-01-01

    Antares is a 24-beam 40-TW carbon-dioxide (CO/sub 2/) laser fusion system currently under construction at the Los Alamos National Laboratory. The Antares alignment gimbal positioner (AGP) is an optomechanical instrument that will be used for target alignment and alignment of the 24 laser beams, as well as beam quality assessments. The AGP will be capable of providing pointing, focusing, and wavefront optical path difference, as well as aberration information at both helium-neon (He-Ne) and CO/sub 2/ wavelengths. It is designed to allow the laser beams to be aligned to any position within a 1-cm cube to a tolerance of 10 ..mu..m.

  9. Advanced Ground Systems Maintenance Cryogenics Test Lab Control System Upgrade Project

    NASA Technical Reports Server (NTRS)

    Harp, Janice Leshay

    2014-01-01

    This project will outfit the Simulated Propellant Loading System (SPLS) at KSC's Cryogenics Test Laboratory with a new programmable logic control system. The control system upgrade enables the Advanced Ground Systems Maintenace Element Integration Team and other users of the SPLS to conduct testing in a controls environment similar to that used at the launch pad.

  10. Operation and Maintenance of Wastewater Collection Systems. Volume II. Third Edition. A Field Study Training Program.

    ERIC Educational Resources Information Center

    California State Univ., Sacramento. Dept. of Civil Engineering.

    Proper installations, inspections, operations, maintenance and repairs of wastewater collection, conveyance and treatment facilities have a significant impact on the operation and maintenance costs, and the effectiveness of these facilities. This manual is the second volume of a two-part program designed to provide wastewater collection system…

  11. Operation and Maintenance of Wastewater Collection Systems. Volume I. Third Edition. A Field Study Training Program.

    ERIC Educational Resources Information Center

    California State Univ., Sacramento. Dept. of Civil Engineering.

    Proper installations, inspections, operations, maintenance and repairs of wastewater collection, conveyance and treatment facilities have a significant impact on the operation and maintenance costs, and the effectiveness of these facilities. This manual is the first volume of a two-part program designed to provide wastewater collection system…

  12. Assessment of acetabulum anteversion aligned with the transverse acetabulum ligament: cadaveric study using image-free navigation system.

    PubMed

    Fukui, Tomokazu; Fukunishi, Shigeo; Nishio, Shoji; Fujihara, Yuki; Shohei, Okahisa; Yoshiya, Shinichi

    2013-02-22

    The transverse acetabulum ligament (TAL) has been used as an intraoperative anatomical landmark to position the acetabulum cup in total hip arthroplasty (THA). However, the validity of the use of TAL has not been clarified. The purpose of this study was to examine the orientation of the cup component aligned with the TAL in cadaveric study. The 31 hips in 25 whole-body embalmed cadavers were examined. The donors were 12 men and 13 women. Simulated THA procedure using image-free navigation system was performed and a trial cup with a diameter of approximately 2 mm less than the size of the acetabulum were inserted and snugly fitted on the TAL through the posterior wall of acetabulum. The orientation of the cup component was measured using an image-free THA navigation system. The measured radiographic anteversion and inclination angles averaged 18.2±7.2° (range: 2.0-33.2°) and 43.5±4.2° (range: 33.1-51.0°) respectively. Based on the Lewinnek's safe zone criteria, 26 hips (80.6%) were judged to be within the. Moreover, in the analysis of the gender difference of TAL angles, the average anteversion angle was shown to be significant larger in female than male population. The TAL can be effectively used an intraoperative landmark to align the acetabulum component helping reduce the risk of dislocation after surgery. In the intraoperative judgment, a gender difference in the alignment of the TAL should be taken into consideration. PMID:23705063

  13. Bright single photon source based on self-aligned quantum dot-cavity systems.

    PubMed

    Maier, Sebastian; Gold, Peter; Forchel, Alfred; Gregersen, Niels; Mørk, Jesper; Höfling, Sven; Schneider, Christian; Kamp, Martin

    2014-04-01

    We report on a quasi-planar quantum-dot-based single-photon source that shows an unprecedented high extraction efficiency of 42% without complex photonic resonator geometries or post-growth nanofabrication. This very high efficiency originates from the coupling of the photons emitted by a quantum dot to a Gaussian shaped nanohill defect that naturally arises during epitaxial growth in a self-aligned manner. We investigate the morphology of these defects and characterize the photonic operation mechanism. Our results show that these naturally arising coupled quantum dot-defects provide a new avenue for efficient (up to 42% demonstrated) and pure (g(2)(0) value of 0.023) single-photon emission. PMID:24718190

  14. A measurement system for quick rail inspection and effective track maintenance strategy

    NASA Astrophysics Data System (ADS)

    Bocciolone, M.; Caprioli, A.; Cigada, A.; Collina, A.

    2007-04-01

    Safety and environment impact of urban railway play a primary role in the management of Public Transportation Companies. One of the critical problem is track maintenance activity, requiring a reliable knowledge of the rail status (such as, for urban transport system, corrugation and localised damage) so that a proper intervention can be performed only when necessary. The public transportation company of Milan (ATM S.p.A.) has started a cooperation with Politecnico di Milano to develop new techniques for track condition inspection, through accelerometer measurements performed on standard operating bogies. This avoids the use of special cars that can operate only when traffic is stopped and permits the collection of a large amount of data improving reliability through measurement repetitions. A feasibility study of a foolproof diagnostic tool is developed in this paper. In particular, it shows the best measurement points, how the sub-structure on which the train is travelling, and the travelling conditions influence the recorded vibration levels. Signal processing techniques, at this stage, are still off-line. Anyway the system has already been designed in order to work under "real time" conditions (a prototype is already existing), also reducing the huge amount of collected data to keep only the essential ones. The attentions have been focused here on the measurement problem, postponing the theoretical aspects to a future paper.

  15. A system for studying mechanisms of neuromuscular junction development and maintenance.

    PubMed

    Vilmont, Valérie; Cadot, Bruno; Ouanounou, Gilles; Gomes, Edgar R

    2016-07-01

    The neuromuscular junction (NMJ), a cellular synapse between a motor neuron and a skeletal muscle fiber, enables the translation of chemical cues into physical activity. The development of this special structure has been subject to numerous investigations, but its complexity renders in vivo studies particularly difficult to perform. In vitro modeling of the neuromuscular junction represents a powerful tool to delineate fully the fine tuning of events that lead to subcellular specialization at the pre-synaptic and post-synaptic sites. Here, we describe a novel heterologous co-culture in vitro method using rat spinal cord explants with dorsal root ganglia and murine primary myoblasts to study neuromuscular junctions. This system allows the formation and long-term survival of highly differentiated myofibers, motor neurons, supporting glial cells and functional neuromuscular junctions with post-synaptic specialization. Therefore, fundamental aspects of NMJ formation and maintenance can be studied using the described system, which can be adapted to model multiple NMJ-associated disorders. PMID:27226316

  16. A system for studying mechanisms of neuromuscular junction development and maintenance

    PubMed Central

    Vilmont, Valérie; Ouanounou, Gilles

    2016-01-01

    The neuromuscular junction (NMJ), a cellular synapse between a motor neuron and a skeletal muscle fiber, enables the translation of chemical cues into physical activity. The development of this special structure has been subject to numerous investigations, but its complexity renders in vivo studies particularly difficult to perform. In vitro modeling of the neuromuscular junction represents a powerful tool to delineate fully the fine tuning of events that lead to subcellular specialization at the pre-synaptic and post-synaptic sites. Here, we describe a novel heterologous co-culture in vitro method using rat spinal cord explants with dorsal root ganglia and murine primary myoblasts to study neuromuscular junctions. This system allows the formation and long-term survival of highly differentiated myofibers, motor neurons, supporting glial cells and functional neuromuscular junctions with post-synaptic specialization. Therefore, fundamental aspects of NMJ formation and maintenance can be studied using the described system, which can be adapted to model multiple NMJ-associated disorders. PMID:27226316

  17. AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XXII, I--MAINTAINING THE FUEL SYSTEM (PART I)--CUMMINS DIESEL ENGINE, II--UNDERSTANDING THE DIFFERENTIAL.

    ERIC Educational Resources Information Center

    Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

    THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE FUNCTION AND MAINTENANCE OF THE DIESEL ENGINE FUEL SYSTEM AND DIFFERENTIAL DRIVE UNITS USED IN DIESEL POWERED VEHICLES. TOPICS ARE (1) FUEL SYSTEM COMPARISONS, (2) FUEL SYSTEM SUPPLY COMPONENTS, (3) FUEL SUPPLY SECTION MAINTENANCE, (4) FUNCTION OF THE DIFFERENTIAL,…

  18. Lessons Learned in Systemic District Reform: A Cross-District Analysis from the Comprehensive Aligned Instructional System (CAIS) Benchmarking Study

    ERIC Educational Resources Information Center

    Waters, Louise Bay; Vargo, Merrill

    2008-01-01

    Urban district reform has been hampered by the challenge of understanding and supporting the tremendous complexity of district change. Improving this understanding through actionable, practice-based research is the purpose of this study. The authors began the study with the hypothesis that achieving districts both align their instructional systems…

  19. 40 CFR Table 41 to Subpart Uuu of... - Requirements for Installation, Operation, and Maintenance of Continuous Parameter Monitoring Systems

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Requirements for Installation, Operation, and Maintenance of Continuous Parameter Monitoring Systems 41 Table 41 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS...

  20. 40 CFR Table 41 to Subpart Uuu of... - Requirements for Installation, Operation, and Maintenance of Continuous Parameter Monitoring Systems

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Requirements for Installation, Operation, and Maintenance of Continuous Parameter Monitoring Systems 41 Table 41 to Subpart UUU of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NATIONAL EMISSION STANDARDS FOR HAZARDOUS...