Science.gov

Sample records for aliphatic hydrocarbon solvent

  1. 40 CFR Table 2b to Subpart E of... - Reactivity Factors for Aliphatic Hydrocarbon Solvent Mixtures

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... Hydrocarbon Solvent Mixtures 2B Table 2B to Subpart E of Part 59 Protection of Environment ENVIRONMENTAL... Hydrocarbon Solvent Mixtures Bin Averageboiling point * (degrees F) Criteria Reactivityfactor 1 80-205 Alkanes... + Dry Point) / 2 (b) Aromatic Hydrocarbon Solvents...

  2. 40 CFR Table 2b to Subpart E of... - Reactivity Factors for Aliphatic Hydrocarbon Solvent Mixtures

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Hydrocarbon Solvent Mixtures 2B Table 2B to Subpart E of Part 59 Protection of Environment ENVIRONMENTAL... Hydrocarbon Solvent Mixtures Bin Averageboiling point * (degrees F) Criteria Reactivityfactor 1 80-205 Alkanes... + Dry Point) / 2 (b) Aromatic Hydrocarbon Solvents...

  3. 40 CFR Table 2b to Subpart E of... - Reactivity Factors for Aliphatic Hydrocarbon Solvent Mixtures

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... Hydrocarbon Solvent Mixtures 2B Table 2B to Subpart E of Part 59 Protection of Environment ENVIRONMENTAL... Hydrocarbon Solvent Mixtures Bin Averageboiling point* (degrees F) Criteria Reactivityfactor (g O3/g VOC) 1 80... Point + Dry Point)/2(b) Aromatic Hydrocarbon Solvents...

  4. 40 CFR Table 2b to Subpart E of... - Reactivity Factors for Aliphatic Hydrocarbon Solvent Mixtures

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Hydrocarbon Solvent Mixtures 2B Table 2B to Subpart E of Part 59 Protection of Environment ENVIRONMENTAL... Hydrocarbon Solvent Mixtures Bin Averageboiling point* (degrees F) Criteria Reactivityfactor (g O3/g VOC) 1 80... Point + Dry Point)/2(b) Aromatic Hydrocarbon Solvents...

  5. 40 CFR Table 2b to Subpart E of... - Reactivity Factors for Aliphatic Hydrocarbon Solvent Mixtures

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... Hydrocarbon Solvent Mixtures 2B Table 2B to Subpart E of Part 59 Protection of Environment ENVIRONMENTAL... Hydrocarbon Solvent Mixtures Bin Averageboiling point* (degrees F) Criteria Reactivityfactor (g O3/g VOC) 1 80... Point + Dry Point)/2(b) Aromatic Hydrocarbon Solvents...

  6. Aliphatic hydrocarbons of the fungi.

    NASA Technical Reports Server (NTRS)

    Weete, J. D.

    1972-01-01

    Review of studies of aliphatic hydrocarbons which have been recently detected in the spores of phytopathogenic fungi, and are found to be structurally very similar to the alkanes of higher plants. It appears that the hydrocarbon components of the few mycelial and yeast forms reported resemble the distribution found in bacteria. The occurence and distribution of these compounds in the fungi is discussed. Suggested functional roles of fungal spore alkanes are presented.

  7. Aliphatic hydrocarbons of the Murchison meteorite

    NASA Technical Reports Server (NTRS)

    Cronin, John R.; Pizzarello, Sandra

    1990-01-01

    Hydrocarbon fractions from the Murchison meteorite were prepared using benzene-methanol as the extraction solvent, fractionated on silica gel columns, and analyzed using gas chromatography combined with mass spectrometry and IR and NMR techniques. Results indicate that the most abundant aliphatic hydrocarbon components of the Murchison meteorite are C15 to C30 branched-alkyl-substituted mono-, di-, and tricyclic alkanes. It is shown that the n-alkanes, methyl alkanes, and isoprenoid alkanes that are sometimes found in extracts of the Murchison meteorite are terrestrial contaminants.

  8. Oxygenases for aliphatic hydrocarbons and fatty acids

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Oxygenases catalyzing the insertion of oxygen into either aliphatic hydrocarbons or fatty acids have great similarity. There are two classes of oxygenases: monooxygenases and dioxygenases. Dioxygenase inserts both atoms of molecular oxygen into a substrate, whereas monooxygenase incorporates one a...

  9. Spreading coefficients of aliphatic hydrocarbons on water

    SciTech Connect

    Takii, Taichi; Mori, Y.H. . Dept. of Mechanical Engineering)

    1993-11-01

    Experiments have been performed to determine the equilibrium spreading coefficients of some aliphatic hydrocarbons (C[sub 6]C[sub 10]) on water. The thickness of a discrete lens of each hydrocarbon sample floating on a stagnant water pool was measured interferometrically and used to calculate the spreading coefficient of the hydrocarbon with the aid of Langmuir's capillarity theory. The dependences of the spreading coefficient, thus observed, on temperature (0--50 C) and on the number of carbon atoms in the hydrocarbon molecule are in qualitative agreement with the predictions based on the Lifshitz theory of van der Waals forces.

  10. Stable isotope investigations of chlorinated aliphatic hydrocarbons.

    SciTech Connect

    Abrajano, T.; Heraty, L. J.; Holt, B. D.; Huang, L.; Sturchio, N. C.

    1999-06-01

    Stable isotope ratio measurements for carbon (C) and chlorine (Cl) can be used to elucidate the processes affecting transformation and transportation of chlorinated aliphatic hydrocarbons (CAHs) in the environment. Methods recently developed in our laboratory for isotopic analysis of CAHs have been applied to laboratory measurements of the kinetic isotope effects associated with aerobic degradation of dichloromethane (DCM) and with both anaerobic and aerobic cometabolic degradation of trichlomethene (TCE) in batch and column microbial cultures. These experimental determinations of fractionation factors are crucial for understanding the behavior of CAHs in complex natural systems, where the extent of biotransformation can be masked by dispersion and volatilization. We have also performed laboratory investigations of kinetic isotope effects accompanying evaporation of CAHs, as well as field investigations of natural attenuation and in situ remediation of CAHs in a number of contaminated shallow aquifers at sites operated by the federal government and the private sector.

  11. The effect of aliphatic fuel constituents on the biodegradation of polycyclic aromatic hydrocarbons

    SciTech Connect

    Gamerdinger, A.P.

    1995-12-01

    In petroleum-derived waste, n-alkanes are often codeposited with polycyclic aromatic hydrocarbons (PAHs). The impact of aliphatic fuel constituents on the biodegradation of the more toxic PAHs is considered. Biodegradation of naphthalene by a Coryneform bacteria was examined in biphasic, slurry systems containing and aliphatic solvent in addition to the aqueous phase. The effect of solvent hydrophobicity was evaluated by varying the solvent treatment; a homologous series of n-alkanes was used. Relative to an aqueous system (no solvent), the extent of naphthalene degradation was enhanced in the presence of decane, dodecane, and hexadecane. Biodegradation was apparent, but decreased in the presence of octane, and was completely absent in the presence of hexane. The impact of aliphatic constituents on PAH biodegradation is a function of solvent hydrophobicity. The results indicate that the presence of multiple chemical constituents in complex systems modifies bioavailability and biodegradation.

  12. 40 CFR Table 6 to Subpart Vvvv of... - Default Organic HAP Contents of Petroleum Solvent Groups

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Spirits 150 EC, Naphtha, Mixed Hydrocarbon, Aliphatic Hydrocarbon, Aliphatic Naptha, Naphthol Spirits... Aromatic Naphtha, Light Aromatic Hydrocarbons, Aromatic Hydrocarbons, Light Aromatic Solvent.) 6 4%...

  13. 40 CFR Table 4 to Subpart Rrrr of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups 1

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... EC, Naphtha, Mixed Hydrocarbon, Aliphatic Hydrocarbon, Aliphatic Naphtha, Naphthol Spirits, Petroleum..., High-flash Naphtha, Aromatic Naphtha, Light Aromatic Naphtha, Light Aromatic Hydrocarbons, Aromatic Hydrocarbons, Light Aromatic Solvent....

  14. 40 CFR Table 4 to Subpart Pppp of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... aliphatic or aromatic. b Mineral Spirits 135, Mineral Spirits 150 EC, Naphtha, Mixed Hydrocarbon, Aliphatic Hydrocarbon, Aliphatic Naphtha, Naphthol Spirits, Petroleum Spirits, Petroleum Oil, Petroleum Naphtha, Solvent... Naphtha, Light Aromatic Hydrocarbons, Aromatic Hydrocarbons, Light Aromatic Solvent....

  15. 40 CFR Table 4 to Subpart Mmmm of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... aliphatic or aromatic. b Mineral Spirits 135, Mineral Spirits 150 EC, Naphtha, Mixed Hydrocarbon, Aliphatic Hydrocarbon, Aliphatic Naphtha, Naphthol Spirits, Petroleum Spirits, Petroleum Oil, Petroleum Naphtha, Solvent... Naphtha, Light Aromatic Hydrocarbons, Aromatic Hydrocarbons, Light Aromatic Solvent....

  16. 40 CFR Table 4 to Subpart Mmmm of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... aliphatic or aromatic. b Mineral Spirits 135, Mineral Spirits 150 EC, Naphtha, Mixed Hydrocarbon, Aliphatic Hydrocarbon, Aliphatic Naphtha, Naphthol Spirits, Petroleum Spirits, Petroleum Oil, Petroleum Naphtha, Solvent... Naphtha, Light Aromatic Hydrocarbons, Aromatic Hydrocarbons, Light Aromatic Solvent....

  17. Biodegradation of aliphatic vs. aromatic hydrocarbons in fertilized arctic soils

    USGS Publications Warehouse

    Braddock, J.F.

    1999-01-01

    A study was carried out to test a simple bioremediation treatment strategy in the Arctic and analyze the influence of fertilization the degradation of aliphatic and aromatic hydrocarbons, e.g., pristine, n-tetradecane, n-pentadecane, 2-methylnaphthalene, naphthalene, and acenaphthalene. The site was a coarse sand pad that once supported fuel storage tanks. Diesel-range organics concentrations were 250-860 mg/kg soil at the beginning of the study. Replicate field plots treated with fertilizer yielded final concentrations of 0, 50, 100, or 200 mg N/kg soil. Soil pH and soil-water potentials decreased due to fertilizer application. The addition of fertilizer considerably increased soil respiration potentials, but not the populations of microorganisms measured. Fertilizer addition also led to ??? 50% loss of measured aliphatic and aromatic hydrocarbons in surface and subsurface soils. For fertilized plots, hydrocarbon loss was not associated with the quantity of fertilizer added. Losses of aliphatic hydrocarbons were ascribed to biotic processes, while losses of aromatic hydrocarbons were due to biotic and abiotic processes.

  18. Determination of aliphatic hydrocarbons in the alga Himanthalia elongata.

    PubMed

    Punín Crespo, M O; Lage Yusty, M A

    2004-02-01

    The algae considered new foods according to Regulation CE 258/97 need a guarantee of their healthfulness before being in the European market. In this work ten samples of the brown alga Himanthalia elongata have been analyzed with the aim of verifying the absence of aliphatic hydrocarbons, due to the ability of the macroalgae to capture lipophilic organic compounds of the marine water coming from accidental or continuous leaks of raw oil and refined products, which happen each year with the growth of the industrialization and the demand of energy. The fat of the samples were Soxhlet extracted using hexane:dichloromethane (1:1) for 7h. The organic fractions were purified using silica microcolumns. The identification and quantification of the aliphatic hydrocarbons have been carried out using gas chromatography (GC) with flame ionization detector (FID). The total hydrocarbon content was between 14.8 and 40.2 microg g(-1) dry weight. PMID:14759670

  19. Aliphatics hydrocarbon content in surface sediment from Jakarta Bay, Indonesia

    NASA Astrophysics Data System (ADS)

    YAzis, M.; Asia, L.; Piram, A.; Doumenq, P.; Syakti, A. D.

    2016-02-01

    Sedimentary aliphatic hydrocarbons content have been studied quantitatively and qualitatively using GC/MS method in eight coastal stations located in the Jakarta Bay, North of Jakarta, Indonesia. The total concentrations n-alkanes have ranged from 480 μg.kg-1to 1,935 μg.kg-1sediment dry weight. Several ratios (e.g. CPI24-32, NAR, TAR, Pr/Phy, n-C17/Pr, n- C18/Phyt,n-C29/n-C17, Ʃn-alkanes/n-C16LMW/HMW, Paq and TMD) were used to evaluate the possible sources of terrestrial-marine inputs of these hydrocarbons in the sediments. The various origins of aliphatic hydrocarbons were generally biogenic, including both terrigenous and marine, with an anthropogenic pyrolytic contribution (petrogenic and biogenic combustion). Two stations (G,H) were thehighest concentration and had potential risk to environment

  20. Aerobic microorganism for the degradation of chlorinated aliphatic hydrocarbons

    DOEpatents

    Fliermans, Carl B.

    1989-01-01

    A chlorinated aliphatic hydrocarbon-degrading microorganism, having American Type Culture Collection accession numbers ATCC 53570 and 53571, in a biologically pure culture aseptically collected from a deep subsurface habitat and enhanced, mineralizes trichloroethylene and tetrachloroethylene to HCl, H.sub.2 O and Co.sub.2 under aerobic conditions stimulated by methane, acetate, methanol, tryptone-yeast extract, propane and propane-methane.

  1. Aliphatic hydrocarbons in Great Barrier Reef organisms and environment

    NASA Astrophysics Data System (ADS)

    Coates, M.; Connell, D. W.; Bodero, J.; Miller, G. J.; Back, R.

    1986-07-01

    This investigation was undertaken to assess the chemical nature, occurrence, and possible origin of petroleum hydrocarbons in the Great Barrier Reef ecosystem. Aliphatic hydrocarbons in surface sediments, water, and a suite of seven species from widely separated coral reefs in the Great Barrier Reef area were analysed by gas chromatography, and by gas chromatography coupled with mass spectrometry. The hydrocarbons found were substantially of biogenic origin. The major components were n-pentadecane, n-heptadecane, pristane and mono-alkenes based on heptadecane, and were believed to originate from benthic algae and phytoplankton. There was no evidence to suggest that lipid content had any influence on hydrocarbon content. Hydrocarbons from the organisms and sediments have characteristic composition patterns which would be altered by the presence of petroleum hydrocarbons. An unresolved complex mixture, usually considered indicative of petroleum contamination, was found in greater than trace amounts only in Holothuria (sea cucumber) and Acropora (coral) from the Capricorn Group, and in some sediment samples from the Capricorn Group and Lizard Island area.

  2. Quantitative separation of aliphatic and aromatic hydrocarbons using silver ion--silica solid-phase extraction

    PubMed

    Bennett; Larter

    2000-03-01

    A solid-phase extraction (SPE) method employing silver nitrate impregnated silica has been developed and evaluated for the separation of defined aliphatic and aromatic hydrocarbons from crude oils. The versatility of the SPE method is demonstrated using a light crude oil from the North Sea and a heavy crude oil from Orcutt field (Monterey, California, U.S.A.). The coefficients of variation for a number of geochemical parameters measured on both aliphatic and aromatic hydrocarbons were excellent. The separation efficiency of SPE is demonstrated using quantification of monoaromatic steroid hydrocarbons which are notoriously difficult to efficiently sequester into the aromatic hydrocarbon fraction using traditional liquid chromatographic procedure. The selectivity and efficiency of the SPE technique is comparable with that of silica gel TLC. However, losses of volatile compounds such as naphthalene are limited during SPE since the sample remains in solvent. We conclude that solid-phase extraction affords rapid sample turnover suitable for processing large sample numbers with high reproducibility. PMID:10739209

  3. Complexes of ruthenium and rhodium with aliphatic amines in the catalysis of hydrogenation of unsaturated hydrocarbons

    SciTech Connect

    Turisbekova, K.K.; Shuikina, L.P.; Parenago, O.P.; Frolov, V.F.

    1989-02-01

    The authors synthesized new catalysts highly active in the hydrogenations of unsaturated hydrocarbons, based on complexes of ruthenium and rhodium with higher aliphatic amines, which are soluble in aromatic solvents. The complexes acquired catalytic activity in hydrogenation as a result of their treatment with diisobutyl aluminum hydride. Olefins (1-hexene, cyclopentene, cyclohexene) or dienes (isoprene) were used as the unsaturated compounds. For the ruthenium based catalysts, the highest activity was observed during the hydrogenation of 1-hexene. For the rhodium-based catalysts, the activity in the hydrogenation of olefins and dienes was approximately the same. In the case of the rhodium complex catalysts, the hydrogenation of 1-hexene was accompanied by a side-reaction consisting in isomerization into olefins with inner double bonds.

  4. ANAEROBIC TRANSFORMATION OF CHLORINATED ALIPHATIC HYDROCARBONS IN A SAND AQUIFER BASED ON SPATIAL CHEMICAL DISTRIBUTIONS

    EPA Science Inventory

    We estimated the distribution of chlorinated aliphatic hydrocarbons (CAHs) from groundwater samples collected along three transects in a sand aquifer. richloroethylene (TCE) leaked and contaminated the aquifer probably more than a decade before we collected the measurements. he d...

  5. CHEMICAL DISTRIBUTION AND ANAEROBIC TRANSFORMATION OF CHLORINATED ALIPHATIC HYDROCARBONS IN A SAND AQUIFER

    EPA Science Inventory

    We estimated the distribution of chlorinated aliphatic hydrocarbons (CAHS) from groundwater samples collected along three transects in a sand aquifer. richloroethylene (TCE) leaked and contaminated the aquifer probably more than a decade before we collected the measurements. he d...

  6. A statistical approach to the interpretation of aliphatic hydrocarbon distributions in marine sediments

    USGS Publications Warehouse

    Rapp, J.B.

    1991-01-01

    Q-mode factor analysis was used to quantitate the distribution of the major aliphatic hydrocarbon (n-alkanes, pristane, phytane) systems in sediments from a variety of marine environments. The compositions of the pure end members of the systems were obtained from factor scores and the distribution of the systems within each sample was obtained from factor loadings. All the data, from the diverse environments sampled (estuarine (San Francisco Bay), fresh-water (San Francisco Peninsula), polar-marine (Antarctica) and geothermal-marine (Gorda Ridge) sediments), were reduced to three major systems: a terrestrial system (mostly high molecular weight aliphatics with odd-numbered-carbon predominance), a mature system (mostly low molecular weight aliphatics without predominance) and a system containing mostly high molecular weight aliphatics with even-numbered-carbon predominance. With this statistical approach, it is possible to assign the percentage contribution from various sources to the observed distribution of aliphatic hydrocarbons in each sediment sample. ?? 1991.

  7. 40 CFR Table 4 to Subpart Rrrr of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups 1

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Spirits 150 EC, Naphtha, Mixed Hydrocarbon, Aliphatic Hydrocarbon, Aliphatic Naphtha, Naphthol Spirits... Naphtha, High-flash Naphtha, Aromatic Naphtha, Light Aromatic Naphtha, Light Aromatic Hydrocarbons, Aromatic Hydrocarbons, Light Aromatic Solvent....

  8. 40 CFR Table 6 to Subpart Qqqq of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Spirits 150 EC, Naphtha, Mixed Hydrocarbon, Aliphatic Hydrocarbon, Aliphatic Naphtha, Naphthol Spirits... Naphtha, High-flash Naphtha, Aromatic Naphtha, Light Aromatic Naphtha, Light Aromatic Hydrocarbons, Aromatic Hydrocarbons, Light Aromatic Solvent....

  9. 40 CFR Table 4 to Subpart Nnnn of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... Spirits 150 EC, Naphtha, Mixed Hydrocarbon, Aliphatic Hydrocarbon, Aliphatic Naphtha, Naphthol Spirits... Naphtha, High-flash Naphtha, Aromatic Naphtha, Light Aromatic Naphtha, Light Aromatic Hydrocarbons, Aromatic Hydrocarbons, Light Aromatic Solvent....

  10. 40 CFR Table 5 to Subpart Oooo of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., Mineral Spirits 150 EC, Naphtha, Mixed Hydrocarbon, Aliphatic Hydrocarbon, Aliphatic Naphtha, Naphthol...-flash Naphtha, High-flash Naphtha, Aromatic Naphtha, Light Aromatic Naphtha, Light Aromatic Hydrocarbons, Aromatic Hydrocarbons, Light Aromatic Solvent....

  11. 40 CFR Table 7 to Subpart Kkkk of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Spirits 150 EC, Naphtha, Mixed Hydrocarbon, Aliphatic Hydrocarbon, Aliphatic Naphtha, Naphthol Spirits... Naphtha, High-flash Naphtha, Aromatic Naphtha, Light Aromatic Naphtha, Light Aromatic Hydrocarbons, Aromatic Hydrocarbons, Light Aromatic Solvent....

  12. Aliphatic Hydrocarbons in Surface Sediments of Willapa Bay and Grays Harbor, Washington

    USGS Publications Warehouse

    Rapp, J.B.; Kvenvolden, K.A.; Clifton, H.E.

    1982-01-01

    Willapa Bay and Grays Harbor are two adjacent estuaries along the coast of Washington state. Willapa Bay is a recreational area minimally affected by industry; Grays Harbor, on the other hand, is moderately industrialized. Aliphatic hydrocarbons in surface sediments from these two estuaries reflect the differences in human activities. For example, the mean concentration of aliphatic hydrocarbons for seven stations in Willapa Bay is 1,000 ?g/g (relative to organic carbon) while in Grays Harbor this mean concentration for six stations is 1,900 ?g/g. The difference is attributed mainly to the greater urban and industrial pollution in Grays Harbor. The gas chromatographic records of aliphatic hydrocarbons also reflect the extent of hydrocarbon pollution by the presence of a chromatographically unresolved mixture of hydrocarbons. This kind of mixture is more evident in sediments from Grays Harbor, and in both estuaries it is more concentrated in sediments collected nearest to urban centers.

  13. Aliphatic hydrocarbon and polycyclic aromatic hydrocarbon geochemistry of twelve major rivers in the Northwest Territories

    SciTech Connect

    Backus, S.; Swyripa, M.; Peddle, J.; Jeffries, D.S.

    1995-12-31

    Suspended sediment and water samples collected from twelve major rivers in the Northwest Territories were analyzed for aliphatic hydrocarbons and polycyclic aromatic hydrocarbons (PAHs) to assess the sources and transport of hydrocarbons entering the Arctic Ocean. Three stations on the Mackenzie River and one station near the mouth of eleven other northern rivers were selected for sampling. Samples were collected on the Mackenzie River on four occasions to characterize spring, summer and fall flow conditions and once on the remaining eleven rivers during high flow conditions. The Mackenzie River is distinctively different then the other eleven rivers. Naturally occurring hydrocarbons predominate in the river. These hydrocarbons include biogenic alkanes, diagenic PAHs, petrogenic alkanes, and PAHs from oil seeps and/or bitumens. Anthropogenic inputs of PAHs are low as indicated by low concentrations of combustion PAHs. Alkyl PAH distributions indicate that a significant component of the lower molecular weight PAH fraction is petrogenic. The majority of the high molecular weight PAHs, together with the petrogenic PAHs have a principal source in the Mackenzie River.

  14. Membrane separation of hydrocarbons using cycloparaffinic solvents

    DOEpatents

    Kulkarni, S.S.; Chang, Y.A.; Gatsis, J.G.; Funk, E.W.

    1988-06-14

    Heavy crude oils which contain metal contaminants such as nickel, vanadium and iron may be separated from light hydrocarbon oils by passing a solution of the crude oil dissolved in a cycloparaffinic hydrocarbon solvent containing from about 5 to about 8 carbon atoms by passing through a polymeric membrane which is capable of maintaining its integrity in the presence of hydrocarbon compounds. The light hydrocarbon oils which possess relatively low molecular weights will be recovered as the permeate while the heavy oils which possess relatively high molecular weights as well as the metal contaminants will be recovered as the retentate.

  15. Membrane separation of hydrocarbons using cycloparaffinic solvents

    DOEpatents

    Kulkarni, Sudhir S.; Chang, Y. Alice; Gatsis, John G.; Funk, Edward W.

    1988-01-01

    Heavy crude oils which contain metal contaminants such as nickel, vanadium and iron may be separated from light hydrocarbon oils by passing a solution of the crude oil dissolved in a cycloparaffinic hydrocarbon solvent containing from about 5 to about 8 carbon atoms by passing through a polymeric membrane which is capable of maintaining its integrity in the presence of hydrocarbon compounds. The light hydrocarbon oils which possess relatively low molecular weights will be recovered as the permeate while the heavy oils which possess relatively high molecular weights as well as the metal contaminants will be recovered as the retentate.

  16. Biological monitoring of chlorinated hydrocarbon solvents

    SciTech Connect

    Monster, A.C.

    1986-08-01

    The possibility of biological monitoring of exposure to some volatile, halogenated hydrocarbons will be discussed. Most of these agents are widely used as solvents. All agents act on the nervous system as narcotics and differ widely in toxicity. Most of the solvents undergo biotransformation to metabolites. This allows biological assessment of exposure by measurement of the solvent and/or metabolites in exhaled air, blood, and/or urine. However, the same metabolites may occur with exposure to different chlorinated hydrocarbons, eg, trichloroethanol and trichloroacetic acid from exposure to trichloroethene, tetrachloroethene, and 1,1,1-trichloroethane. On the other hand, these agents differ widely in the percentage that is metabolized. There are large gaps in our knowledge, however, and much research will have to be carried out before even tentative data can be established for most of the solvents.

  17. Seasonal distribution of aliphatic hydrocarbons in the Vaza Barris Estuarine System, Sergipe, Brazil.

    PubMed

    Barbosa, José Carlos S; Santos, Lukas G G V; Sant'Anna, Mércia V S; Souza, Michel R R; Damasceno, Flaviana C; Alexandre, Marcelo R

    2016-03-15

    The seasonal assessment of anthropogenic activities in the Vaza Barris estuarine river system, located in the Sergipe state, northeastern Brazil, was performed using the aliphatic hydrocarbon distribution. The aliphatic hydrocarbon and isoprenoid (Pristane and Phytane) concentrations ranged between 0.19μgg(-1) and 8.5μgg(-1) of dry weight. Data were analyzed using Kruskal-Wallis test, with significance level set at p<0.05, and no seasonality distribution change was observed. The Carbon Preference Index (CPI), associated with n-alkanes/n-C16, Low Molecular Weight/High Molecular Weight ratio (LMW/HMW) and Terrigenous to Aquatic Ratio (TAR) suggested biogenic input of aliphatic hydrocarbons for most samples, with significant contribution of higher plants. PMID:26837270

  18. Polymeric membrane and process for separation of aliphatically unsaturated hydrocarbons

    SciTech Connect

    Ho, W.S.W.

    1991-11-05

    This patent describes a process for separating at least one unsaturated hydrocarbon from a hydrocarbon feed steam containing the unsaturated hydrocarbon. It comprises contacting the feed stream against a first side of a solid, homogeneous membrane comprising a hydrophilic polymer selected from the group consisting of a polyvinylalcohol, polyvinylacetate, sulfonyl-containing polymers, polyvinylpyrrolidone, polyethylene oxide, polyacrylamide, copolymers thereof, and blends thereof a transition metal or transition metal ion capable of reversibly complexing with the unsaturated hydrocarbon, and a hydrophilic salt of a Group I metal; and withdrawing at a second side of the membrane a permeate comprising the unsaturated hydrocarbon in higher concentration than in the feed stream. This patent also describes a solid, homogeneous membrane for separating at least one unsaturated hydrocarbon from a hydrocarbon stream containing the unsaturated hydrocarbon. It comprises a hydrophilic polymer selected from the group consisting of polyvinylalcohol, polyvinylacetate, sulfonyl-containing polymers, polyvinylpyrrolidone, polyethylene oxide, polyacrylamide, copolymers thereof, and blends thereof, a transition metal or transition metal ion capable of reversibly complexing with the unsaturated hydrocarbon, and a hydrophilic salt of a Group I metal.

  19. 27 CFR 21.125 - Rubber hydrocarbon solvent.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Rubber hydrocarbon solvent. 21.125 Section 21.125 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU....125 Rubber hydrocarbon solvent. (a) Rubber hydrocarbon solvent is a petroleum derivative....

  20. 27 CFR 21.125 - Rubber hydrocarbon solvent.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2013-04-01 2013-04-01 false Rubber hydrocarbon solvent. 21.125 Section 21.125 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU....125 Rubber hydrocarbon solvent. (a) Rubber hydrocarbon solvent is a petroleum derivative....

  1. 27 CFR 21.125 - Rubber hydrocarbon solvent.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2011-04-01 2011-04-01 false Rubber hydrocarbon solvent. 21.125 Section 21.125 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU....125 Rubber hydrocarbon solvent. (a) Rubber hydrocarbon solvent is a petroleum derivative....

  2. 27 CFR 21.125 - Rubber hydrocarbon solvent.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2014-04-01 2014-04-01 false Rubber hydrocarbon solvent. 21.125 Section 21.125 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU....125 Rubber hydrocarbon solvent. (a) Rubber hydrocarbon solvent is a petroleum derivative....

  3. 27 CFR 21.125 - Rubber hydrocarbon solvent.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2012-04-01 2012-04-01 false Rubber hydrocarbon solvent. 21.125 Section 21.125 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU....125 Rubber hydrocarbon solvent. (a) Rubber hydrocarbon solvent is a petroleum derivative....

  4. Polymeric membrane and process for separating aliphatically unsaturated hydrocarbons

    SciTech Connect

    Ho, W.S.W.

    1991-05-14

    This patent describes a process for separating at least one unsaturated hydrocarbon from a hydrocarbon feed stream containing. It comprises: contacting the feed stream against a first side of a solid, homogeneous membrane consisting essentially of a hydrophilic polymer selected from the group consisting of polyvinylalcohol, polyvinylacetate, sulfonyl containing polymers, polyvinylpyrrolidone, polyethylene oxide, polyacrylamide, copolymers thereof, and blends thereof, and a metal or metal ion capable of reversibly complexing with the unsaturated hydrocarbon, the metal or metal ion is distributed homogeneously in the hydrophilic polymer; and withdrawing at a second side of the membrane a permeate comprising the unsaturated hydrocarbon in higher concentration than in the feed stream; whereby the membrane provides high permeability and selectivity for unsaturated hydrocarbons and substantially increases the rate at which the permeate is withdrawn.

  5. SELECTIVE ENUMERATION OF AROMATIC AND ALIPHATIC HYDROCARBON DEGRADING BACTERIA BY A MOST-PROBABLE-NUMBER PROCEDURE

    EPA Science Inventory

    A most-portable-number (MPN) procedure was developed to separately enumerate aliphatic and aromatic hydrocarbon degrading bacteria, because most of the currently available methods are unable to distinguish between these two groups. Separate 96-well microtiter plates are used to ...

  6. A Theoretical Study on the Vibrational Spectra of Polycyclic Aromatic Hydrocarbon Molecules with Aliphatic Sidegroups

    NASA Astrophysics Data System (ADS)

    Sadjadi, SeyedAbdolreza; Zhang, Yong; Kwok, Sun

    2015-03-01

    The role of aliphatic side groups in the formation of astronomical unidentified infrared emission (UIE) features is investigated by applying the density functional theory to a series of molecules with mixed aliphatic-aromatic structures. The effects of introducing various aliphatic groups to a fixed polycyclic aromatic hydrocarbon (PAH) core (ovalene) are studied. Simulated spectra for each molecule are produced by applying a Drude profile at T = 500 K while the molecule is kept at its electronic ground state. The vibrational normal modes are classified using a semi-quantitative method. This allows us to separate the aromatic and aliphatic vibrations, and therefore provides clues to what types of vibrations are responsible for the emissions bands at different wavelengths. We find that many of the UIE bands are not pure aromatic vibrational bands but may represent coupled vibrational modes. The effects of aliphatic groups on the formation of the 8 μm plateau are quantitatively determined. The vibrational motions of methyl (-CH3) and methylene (-CH2 -) groups can cause the merging of the vibrational bands of the parent PAH and the forming of broad features. These results suggest that aliphatic structures can play an important role in the UIE phenomenon.

  7. Source apportionment of urban particulate aliphatic and polynuclear aromatic hydrocarbons (PAHs) using multivariate methods.

    PubMed

    Kavouras, I G; Koutrakis, P; Tsapakis, M; Lagoudaki, E; Stephanou, E G; Von Baer, D; Oyola, P

    2001-06-01

    Samples of organic aerosol were collected in Santiago de Chile. An activated-charcoal diffusion denuder was used to strip out organic vapors prior to particle collection. Both polynuclear aromatic hydrocarbons (PAHs) and aliphatic hydrocarbons were determined using gas chromatography/mass spectrometry (GC/MS). Organic particle sources were resolved using both concentration diagnostic ratios and multivariate methods such as hierarchical cluster analysis (HCA) and factor analysis (FA). Four factors were identified based on the loadings of PAHs and n-alkanes and were attributed to the following sources: (1) high-temperature combustion of fuels; (2) fugitive emissions from oil residues; (3) biogenic sources; and (4) unburned fuels. Multilinear regression (MLR) analysis was used to determine emission profiles and contributions of the sources. The reconstructed concentrations of particle phase aliphatic and polynuclear aromatic hydrocarbons were in good agreement (R2 > 0.70) with those measured in Santiago de Chile. PMID:11414034

  8. SPITZER'S VIEW ON AROMATIC AND ALIPHATIC HYDROCARBON EMISSION IN HERBIG Ae STARS

    SciTech Connect

    Acke, B.; Waters, L. B. F. M.; Bouwman, J.; Juhasz, A.; Henning, Th.; Van den Ancker, M. E.; Meeus, G.; Tielens, A. G. G. M.

    2010-07-20

    The chemistry of astronomical hydrocarbons, responsible for the well-known infrared emission features detected in a wide variety of targets, remains enigmatic. Here we focus on the group of young intermediate-mass Herbig Ae stars. We have analyzed the aliphatic and polycyclic aromatic hydrocarbon (PAH) emission features in the infrared spectra of a sample of 53 Herbig Ae stars, obtained with the Infrared Spectrograph aboard the Spitzer Space Telescope. We confirm that the PAH-to-stellar luminosity ratio is higher in targets with a flared dust disk. However, a few sources with a flattened dust disk still show relatively strong PAH emission. Since PAH molecules trace the gas disk, this indicates that gas disks may still be flared, while the dust disk has settled due to grain growth. There are indications that the strength of the 11.3 {mu}m feature also depends on dust disk structure, with flattened disks being less bright in this feature. We confirm that the CC bond features at 6.2 and 7.8 {mu}m shift to redder wavelengths with decreasing stellar effective temperature. Moreover, we show that this redshift is accompanied by a relative increase of aliphatic CH emission and a decrease of the aromatic 8.6 {mu}m CH feature strength. Cool stars in our sample are surrounded by hydrocarbons with a high aliphatic/aromatic CH ratio and a low aromatic CH/CC ratio, and vice versa for the hot stars. We conclude that, while the overall hydrocarbon emission strength depends on the dust disk's geometry, the relative differences seen in the IR emission features in disks around Herbig Ae stars are mainly due to chemical differences of the hydrocarbon molecules induced by the stellar UV field. Strong UV flux reduces the aliphatic component and emphasizes the spectral signature of the aromatic molecules in the IR spectra.

  9. Biodegradation of individual and multiple chlorinated aliphatic hydrocarbons by methane-oxidizing cultures.

    PubMed Central

    Chang, H L; Alvarez-Cohen, L

    1996-01-01

    The microbial degradation of chlorinated and nonchlorinated methanes, ethanes, and ethanes by a mixed methane-oxidizing culture grown under chemostat and batch conditions is evaluated and compared with that by two pure methanotrophic strains: CAC1 (isolated from the mixed culture) and Methylosinus trichosporium OB3b. With the exception of 1,1-dichloroethylene, the transformation capacity (Tc) for each chlorinated aliphatic hydrocarbon was generally found to be in inverse proportion to its chlorine content within each aliphatic group (i.e., methanes, ethanes, and ethenes), whereas similar trends were not observed for degradation rate constants. Tc trends were similar for all methane-oxidizing cultures tested. None of the cultures were able to degrade the fully chlorinated aliphatics such as perchloroethylene and carbon tetrachloride. Of the four cultures tested, the chemostat-grown mixed culture exhibited the highest Tc for trichloroethylene, cis-1,2-dichloroethylene, tetrachloroethane, 1,1,1-trichloroethane, and 1,2-dichloroethane, whereas the pure batch-grown OB3b culture exhibited the highest Tc for all other compounds tested. The product toxicity of chlorinated aliphatic hydrocarbons in a mixture containing multiple compounds was cumulative and predictable when using parameters measured from the degradation of individual compounds. The Tc for each chlorinated aliphatic hydrocarbon in a mixture (Tcmix) and the total Tc for the mixture (sigma Tcmix) are functions of the individual Tc, the initial substrate concentration (S0), and the first-order rate constant (k/Ks) of each compound in the mixture, indicating the importance of identifying the properties and compositions of all potentially degradable compounds in a contaminant mixture. PMID:8795228

  10. {Polycyclic aromatic hydrocarbons (PAHs) and aliphatic hydrocarbons in gas and particle phases in two sites of Mexico: MILAGRO project}

    NASA Astrophysics Data System (ADS)

    Amador-Muñoz, O.; Villalobos-Pietrini, R.; Castro, T.; Gaspariano-Larino, R.

    2009-04-01

    Aliphatic hydrocarbons are markers of anthropogenic and biogenic emission sources1; meanwhile PAHs are generated by incomplete combustion sources2. The last ones are important compounds due to their carcinogenic and mutagenic properties3,4. The aim of this study was to identify and quantify aliphatic hydrocarbons and PAHs in gas and particles phases of the atmospheric aerosol and to determine the day and night time behavior during the MILAGRO (Megacity Initiative: Local Global and Research Observations) campaign. The gas phase was collected on polyurethane foam, while particles less than 2.5 m (PM2.5) were collected on glass fiber filters covered with Teflon (TIGF, pallflex) of 8x10 in. Samplings were carried out with a high volume sampler (Tisch) with a flow of 1.13 m3 min-1 at two sites: Instituto Mexicano del Petróleo (T0) and Tecamac (T1) located at North and Northeast of Mexico City, respectively during day (7:00 am-7:00 pm) and night time (7:00 pm-7:00 am) from 1 to 29 of March, 2006. Ninteen PAHs and 23 aliphatic hydrocarbons from n-C13H28 to n-C35H72 were analyzed by gas chromatography coupled to mass spectrometry in impact mode. The samples were spiked with deuterads PAHs and aliphatics hydrocarbons before ultrasound extraction. Medians comparisons were made with Mann-Whitney U test. PAHs with molecular weight (MW) less than 228 g mol-1 were distributed in the gas phase, in both sites. Higher concentrations of PAHs ≥ 228 g mol-1 in PM2.5, were observed during night period (p

  11. Aliphatic and polycyclic aromatic hydrocarbons in sediments of the Slovenian coastal area (Gulf of Trieste, northern Adriatic).

    PubMed

    Bajt, Oliver

    2012-12-01

    The distribution and sources of aliphatic and polycyclic aromatic hydrocarbons (PAH) were determined in sediments at seven sites around the Slovenian coastal area. The potential toxicological significance was also assessed using biological thresholds. The results of the analyses showed higher concentrations of hydrocarbons in the Port of Koper and in the Marina of Portoroz. The influence of pollution was also evident in rather higher concentrations of hydrocarbons in the surrounding area in the Bays of Koper and Piran. Concentrations of hydrocarbons decrease toward the central part of the Gulf of Trieste. The major component of the aliphatic fraction was the unresolved complex mixture. Concentrations of the total resolved aliphatic hydrocarbons were in a range from 689 to 3,164 ng g(-1). Concentrations of the total PAHs were between 330 and 1,173 ng g(-1). Polycyclic aromatic hydrocarbons are primarily of pyrolytic origin with some smaller contributions of the petrogenic, while the aliphatic are mostly of petrogenic origin with significant amounts of biogenic derived compounds of terrestrial and marine origin. Strong evidence of the diagenetic origin of perylene in the investigated area was also found. Quite a good linear relationship between PAH concentration and TOC and between aliphatic hydrocarbon concentrations and TOC was observed. The principal component analysis showed differences between the nearshore and offshore sites. In general, the investigated area is moderately contaminated by hydrocarbons. Concentrations of PAHs, hydrocarbons of high concern, are below the levels (effects range low and the effects range median) associated with adverse biological effects. PMID:22270593

  12. Unique gas and hydrocarbon adsorption in a highly porous metal-organic framework made of extended aliphatic ligands.

    PubMed

    Li, Kunhao; Lee, Jeongyong; Olson, David H; Emge, Thomas J; Bi, Wenhua; Eibling, Matthew J; Li, Jing

    2008-12-14

    High and unique gas and hydrocarbon adsorption in a highly stable guest-free microporous metal-organic framework constructed on rigid aliphatic ligands, H(2)bodc and ted, is reported in this work. PMID:19082093

  13. BIOTRANSFORMATION OF MIXTURES OF CHLORINATED ALIPHATIC HYDROCARBONS BY AN ACETATE-GROWN METHANOGENIC ENRICHMENT CULTURE. (R825549C053)

    EPA Science Inventory

    Biotransformation of chlorinated aliphatic hydrocarbons under anaerobic conditions has received considerable attention due to the prevalence of these compounds as groundwater contaminants. However, information concerning the impact of mixtures of chlorinated compounds on their...

  14. Autothermal reforming of aliphatic and aromatic hydrocarbon liquids

    NASA Technical Reports Server (NTRS)

    Flytzani-Stephanopoulos, M.; Voecks, G. E.

    1983-01-01

    Results are presented from a study of the autothermal reforming of paraffins and aromatics over nickel catalysts. The trials were performed to examine the carbon products that appear when steam is passed over hydrocarbon liquids to form H2-rich gases, i.e., the autothermal process (ATR). Attention was given to n-hexane, n-tetradecane, benzene, and benzene solutions of naphthalene with reactant preheat to 1000-1150 F. The carbon-formation limit was sought as a function of the steam-to-carbon and oxygen to carbon molar ratios at constant pressure and the preheat temperatures. The catalyst bed was examined after each trial to identify the locations and types of carbon formed using SEM, thermal gravimetric analysis, and X ray diffraction techniques. The hydrocarbon fuels each had a separate temperature and reaction profile, as well as carbon formation characteristics. No carbon formation was observed in the upper layer of the reactor bed, while both gas phase and surface-grown deposits were present in the lower part. The results are concluded of use in the study of No. 2 fuel oil for ATR feedstock.

  15. Hydrogen addition reactions of aliphatic hydrocarbons in comets

    NASA Astrophysics Data System (ADS)

    Kobayashi, Hitomi; Watanabe, N.; Watanabe, Y.; Fukushima, T.; Kawakita, H.

    2013-10-01

    Comets are thought as remnants of early solar nebula. Their chemical compositions are precious clue to chemical and physical evolution of the proto-planetary disk. Some hydrocarbons such as C2H6, C2H2 and CH4 in comets have been observed by using near-infrared spectroscopy. Although the compositions of C2H6 were about 1% relative to the water in normal comets, there are few reports on the detection of C2H6 in ISM. Some formation mechanisms of C2H6 in ISM have been proposed, and there are two leading hypotheses; one is the dimerizations of CH3 and another is the hydrogen addition reactions of C2H2 on cold icy grains. To evaluate these formation mechanisms for cometary C2H6 quantitatively, it is important to search the C2H4 in comets, which is the intermediate product of the hydrogen addition reactions toward C2H6. However, it is very difficult to detect the C2H4 in comets in NIR (3 microns) regions because of observing circumstances. The hydrogen addition reactions of C2H2 at low temperature conditions are not well characterized both theoretically and experimentally. For example, there are no reports on the reaction rate coefficients of those reaction system. To determine the production rates of those hydrogen addition reactions, we performed the laboratory experiments of the hydrogenation of C2H2 and C2H4. We used four types of the initial composition of the ices: pure C2H4, pure C2H2, C2H2 on amorphous solid water (ASW) and C2H4 on ASW at three different temperatures of 10, 20, and 30K. We found 1) reactions are more efficient when there are ASW in the initial compositions of the ice; 2) hydrogenation of C2H4 occur more rapid than that of C2H2.

  16. IUPAC-NIST Solubility Data Series. 101. Alcohols + Hydrocarbons + Water. Part 2. C1-C3 Alcohols + Aliphatic Hydrocarbons

    NASA Astrophysics Data System (ADS)

    Oracz, Paweł; Góral, Marian; Wiśniewska-Gocłowska, Barbara; Shaw, David G.; Mączyński, Andrzej

    2016-09-01

    The mutual solubilities and related liquid-liquid equilibria for 37 ternary systems of C1-C3 alcohols with aliphatic hydrocarbons and water are exhaustively and critically reviewed. Reports of experimental determination of solubility that appeared in the primary literature prior to the end of 2012 are compiled. For 14 systems, sufficient data are available (two or more independent determinations) to allow critical evaluation. All data are expressed as mass percent and mole fraction as well as the originally reported units. In addition to the standard evaluation criteria used throughout the Solubility Data Series, an additional criterion was used for each of the evaluated systems. These systems include one binary miscibility gap in the hydrocarbon + water subsystem and another one can be in the methanol + hydrocarbon subsystem. The binary tie lines were compared with the recommended values published previously.

  17. Kinetics of aerobic cometabolic biodegradation of chlorinated and brominated aliphatic hydrocarbons: A review.

    PubMed

    Jesus, João; Frascari, Dario; Pozdniakova, Tatiana; Danko, Anthony S

    2016-05-15

    This review analyses kinetic studies of aerobic cometabolism (AC) of halogenated aliphatic hydrocarbons (HAHs) from 2001-2015 in order to (i) compare the different kinetic models proposed, (ii) analyse the estimated model parameters with a focus on novel HAHs and the identification of general trends, and (iii) identify further research needs. The results of this analysis show that aerobic cometabolism can degrade a wide range of HAHs, including HAHs that were not previously tested such as chlorinated propanes, highly chlorinated ethanes and brominated methanes and ethanes. The degree of chlorine mineralization was very high for the chlorinated HAHs. Bromine mineralization was not determined for studies with brominated aliphatics. The examined research period led to the identification of novel growth substrates of potentially high interest. Decreasing performance of aerobic cometabolism were found with increasing chlorination, indicating the high potential of aerobic cometabolism in the presence of medium- and low-halogenated HAHs. Further research is needed for the AC of brominated aliphatic hydrocarbons, the potential for biofilm aerobic cometabolism processes, HAH-HAH mutual inhibition and the identification of the enzymes responsible for each aerobic cometabolism process. Lastly, some indications for a possible standardization of future kinetic studies of HAH aerobic cometabolism are provided. PMID:26874310

  18. Aliphatic hydrocarbons in sediment cores from the southern basin of Lake Michigan

    SciTech Connect

    Doskey, P.V.; Andren, A.W.

    1991-10-01

    Aliphatic hydrocarbons in sediments of the southern basin of Lake Michigan have planktonic, terrigenous, and petroleum residue origins. Surficial sediments collected near the eastern shore in 60-80 m of water contained more petroleum residue and planktonic hydrocarbons and exhibited less terrigenous character than sediments collected from the deepest location in the basin. Petroleum residue inputs have increased since 1900 as evidenced by a change in the flux of an unresolved complex mixture (UCM) of hydrocarbons from 6 ng/cm{sup 2}{center_dot}yr to a flux of approximately 100 ng/cm{sup 2}{center_dot}yr in 1980. Sediment profiles of the UCM exhibited subsurface concentration maxima that may be due to reduced inputs of combustion products or feeding by oligochaetes. Profiles of n-C{sub l7} and pristane indicated that planktonic n-alkanes undergo degradation in the aerobic, mixed zone of the sediments.

  19. Friction of iron lubricated with aliphatic and aromatic hydrocarbons and halogenated analogs

    NASA Technical Reports Server (NTRS)

    Buckley, D. H.

    1976-01-01

    The influence of oxygen and various organic molecules on the reduction of the friction of an iron (011) single crystal surface was investigated. A comparison was made between aliphatic and aromatic structures, all of which contained six carbon atoms, and among various halogen atoms. Results of the investigation indicate that hexane and benzene give similar friction coefficients over a range of loads except at very light loads. At light loads, the friction decreased with an increase in the load where the halogens fluorine and chlorine are incorporated into the benzene molecular structure; however, over the same load range when bromine and iodine were present, the friction was relatively unchanged. The aliphatic compound chlorohexane exhibited lower friction coefficients than the aromatic structure chlorobenzene at very light loads. With the brominated benzene structures, however, friction was essentially the same. Oxygen was more effective in reducing friction than were the simple hydrocarbons.

  20. Solubilities of tetracosane in hydrocarbon solvents

    SciTech Connect

    Brecevic, L.; Garside, J. . Dept. of Chemical Engineering)

    1993-10-01

    The solubilities of tetracosane (n-C[sub 24]H[sub 50]) in heptane (n-C[sub 7]H[sub 16]), dodecane (n-C[sub 12]H[sub 26]), a mixture of isomers of decahydronaphthalene (C[sub 10]H[sub 18]), and m and p-xylene (C[sub 8]H[sub 10]) have been determined over the temperature range 279.3--305.8 K. These solvents were chosen as being representative of the types of molecules present in fuel oils. The results are well described by the equation ln x[sub 2] = [minus]([Delta]H[sup d]/RT) + ([Delta]S[sup d]/R) for which the parameters [Delta]H[sup d] and [Delta]S[sup d] are given. The liquid-phase activity coefficients for the solid at 293.2 K have been derived from the measured solubilities and compared with values calculated from the Scatchard-Hildebrand equation and the UNIFAC group contribution method. Relatively good agreement is obtained using the Scatchard-Hildebrand equation, especially in the case of normal hydrocarbon solvents.

  1. Process for the solvent deasphalting of asphaltene-containing hydrocarbons

    SciTech Connect

    Ikematsu, M.; Honzyo, I.; Sakai, K.

    1985-06-25

    A process for the solvent deasphalting of asphaltene-containing hydrocarbons which comprising mixing asphaltene-containing hydrocarbons with a metal compound such as aluminum carbonates or titanium (IV) oxide and also with a solvent such as n-heptane, n-hexane, n-heptane or a mixed n-pentane.n-butanol solvent, to form a mixture which is then allowed to stand still to precipitate and separate the asphaltene therefrom thereby obtaining a deasphalted oil.

  2. Process for the solvent deasphalting of asphaltene containing hydrocarbons

    SciTech Connect

    Ikematsu, M.; Honzyo, I.; Sakai, K.

    1985-04-30

    A process for the solvent deasphalting of asphaltene-containing hydrocarbons which comprising mixing asphaltene-containing hydrocarbons with a metal compound such as aluminum sulfate or titanium (IV) oxide and also with a solvent such as n-heptane, n-hexane, n-heptane or a mixed n-pentane.n-butanol solvent, to form a mixture which is then allowed to stand still to precipitate and separate the asphaltene therefrom thereby obtaining a deasphalted oil.

  3. A New, Rapid, Precise and Sensitive Method for Chlorine Stable Isotope Analysis of Chlorinated Aliphatic Hydrocarbons

    NASA Astrophysics Data System (ADS)

    van Acker, M. R.; Shahar, A.; Young, E. D.; Coleman, M. L.

    2005-12-01

    Chlorinated aliphatic hydrocarbons (CAH) are recognized common groundwater contaminants. Because of their physico-chemical properties, their lifespan in groundwater is in the order of decades (Pankow and Cherry, 1996). Stable isotopes can play a role in determining the rate and extent of CAH attenuation (Slater, 2003). The use of chlorine has been hampered by the current time consuming and insensitive analytical methods. We present a new analytical procedure to measure chlorine stable isotope values using a gas chromatograph coupled to a multi-collector inductively coupled mass spectrometer (GC-MC-ICP-MS). The GC has a Porapack Q packed column. The carrier gas was helium and the temperature was constant at 160°C. The GC was coupled to the MC-ICP-MS by heated stainless steel tubing. Our high resolution spectra showed that 37Cl is free of its main interference 36Ar-H over a range of 0.004 amu. Two pure CAH, trichloroethene (TCE) and tetrachloroethene (PCE), were used for zero enrichment (sample relative to itself) and standard-sample difference measurements. Integrations and background corrections of transient signals were performed using Microsoft Excel after import of the raw data from the MC-ICPMS acquisition software. Zero enrichment tests with TCE and PCE yielded δ37Cl of -0.04±0.16‰ and -0.03±0.17‰, respectively, results for sample injections of 0.12 to 0.02 microliters. Accuracy was tested by injecting 0.24 microliters of a 50/50 mixture of TCE and PCE of known isotopic compositions as the difference between the two solvents was of paramount interest. The δ37Cl(TCE) value of PCE was -1.99±0.16‰. A highly satisfactory comparison with the conventional method is shown by published values for TCE and PCE, -2.04±0.12‰ and -0.30±0.14‰, respectively (Jendrzejewski et al., 2001), giving a δ37Cl(TCE) value for PCE of -2.34±0.18‰. These tests of the GC-MC-ICP-MS method showed that we can obtain reproducible and accurate Cl isotope values using an

  4. Methyl oleate deoxygenation for production of diesel fuel aliphatic hydrocarbons over Pd/SBA-15 catalysts

    PubMed Central

    2013-01-01

    Background Catalytic deoxygenation is a prominent process for production of renewable fuels from vegetable oil. In this work, deoxygenation of technical grade methyl oleate to diesel fuel aliphatic hydrocarbons (C15 – C18) is evaluated with several parameters including temperature, hydrogen pressure and reaction time in a stirred batch reactor over Pd/SBA-15 catalysts. Results Two different SBA-15 morphologies i.e. spherelike and necklacelike structures have been synthesize as supports for Pd active metal. It is found that Pd dispersion on necklacelike SBA-15 is higher than that of spherelike SBA-15. Notably, higher Pd dispersion on necklacelike SBA-15 provides significant deoxygenation efficiency as compared to Pd/SBA-15-spherelike. Results show that H2 pressures greatly determine the total ester conversion and selectivity to C15 – C18 aliphatic hydrocarbons. Total ester conversions with 55< selectivity to n-heptadecane are achieved using Pd/SBA-15-necklacelike at 270°C and 60 bar H2 pressure within 6 h reaction time. Gas phase study reveals that formation of C17 is generated via indirect decarbonylation when the reaction time is prolonged. Conclusions Pd/SBA-15-necklacelike catalyst exhibits good catalytic performance with high selectivity to diesellike aliphatic hydrocarbons (C15 – C18). The physicochemical properties of the Pd supported on different SBA-15 morphologies influence the deoxygenation activity of the catalysts. Furthermore, the reaction pathways are governed by the H2 pressure as well as reaction duration. PMID:24011181

  5. Use of aliphatic hydrocarbons in feed to decrease body burdens of lipophilic toxicants in livestock

    SciTech Connect

    Rozman, K.; Rozman, T.; Griem, H.; Nieman, I.J.; Smith, G.S.

    1982-01-01

    Sheep were contaminated with hexachlorobenzene and then fed a conventional diet with or without 5% mineral oil or hexadecane. Similar to nonruminant species, both treatments enhanced fecal excretion of hexachlorobenzene about 3-fold and reduced levels of hexachlorobenzene stored in adipose tissue. Normal digestive functions of the animals, including fiber digestion by rumen microbes, were not affected by the administration of the aliphatic hydrocarbons. Dietary administration of mineral oil could be an inexpensive way to save livestock contaminated with toxic lipophilic compounds, such as many pesticides and industrial chemicals.

  6. Organic pollutants in the coastal environment off San Diego, California. 2: Petrogenic and biogenic sources of aliphatic hydrocarbons

    SciTech Connect

    Tran, K.; Yu, C.C.; Zeng, E.Y.

    1997-02-01

    The results from the measurements of aliphatic hydrocarbons suggest that hydrocarbons suggest that hydrocarbons in the Point Loma Wastewater Treatment Plant (PLWTP) effluents are mainly petroleum derived; those in the Tijuana River runoff have largely originated from terrestrial plants with visible petroleum contamination; and those in the sea surface microlayer, sediment traps, and sediments at various coastal locations off San Diego have mostly resulted from biogenic contributions with enhanced microbial products in the summer season. Rainfall in the winter season appeared to amplify the inputs from terrestrial higher plants to the coastal areas. The PLWTP discharged approximately 3.85 metric tons of n-alkanes (C{sub 10}-C{sub 35}) in 1994, well below the level (136 metric tons) estimated in 1979. The input of aliphatic hydrocarbons from the Tijuana River was about 0.101 metric tons in 1994. Diffusion, solubilization, evaporation, and microbial degradation seemed partially responsible for the difference in the concentrations and compositions of aliphatic hydrocarbons in different sample media, although the relative importance of each mechanism cannot be readily discerned from the available data. The results from analyses of aliphatic hydrocarbon compositional indices are generally consistent with those of polycyclic aromatic hydrocarbons.

  7. Vertical fluxes of aromatic and aliphatic hydrocarbons in the Northwestern Mediterranean Sea.

    PubMed

    Deyme, Rémi; Bouloubassi, Ioanna; Taphanel-Valt, Marie-Hélène; Miquel, Juan-Carlos; Lorre, Anne; Marty, Jean-Claude; Méjanelle, Laurence

    2011-12-01

    Aliphatic and aromatic hydrocarbon fluxes were measured in time series sediment trap samples at 200 m and at 1000 m depths in the open Northwestern Mediterranean Sea, from December 2000 to July 2002. Averaged fluxes of n-alkanes, UCM and T-PAH(35) were 2.96 ± 2.60 μg m(-2) d(-1), 64 ± 60 μg m(-2) d(-1) and 0.68 ± 0.59 μg m(-2) d(-1), respectively. Molecular compositions of both hydrocarbon classes showed a contamination in petrogenic hydrocarbons well above the background levels of such an open site, whereas pyrolytic hydrocarbons stand in the range of other open Mediterranean locations. Fluxes displayed ample interannual and seasonal variabilities, mainly related to mass flux variation while concentration evolutions trigger secondary changes in pollutant fluxes. High lithogenic flux events exported particles with a larger pollutant load than biogenic particles formed during the spring bloom and during the summer. Sinking hydrocarbons were efficiently transported from 200 m to 1000 m. PMID:21862192

  8. The early diagenesis of aliphatic hydrocarbons and organic matter in sedimentary particulates from Dabob Bay, Washington

    NASA Astrophysics Data System (ADS)

    Prahl, Fredrick G.; Bennett, Joseph T.; Carpenter, Roy

    1980-12-01

    Aliphatic hydrocarbon compositions were quantitatively characterized in plankton, sediment trap-collected particulate materials and sediments from Dabob Bay using high resolution glass capillary gas chromatography. The average net accumulation of individual hydrocarbons measured in a 1-yr series of sediment traps was compared with the net accumulation of corresponding compounds measured in three depth intervals of 210Pb-dated bottom sediments. Systematic and rapid decreases in the net accumulation of individual hydrocarbons were observed from the sediment traps to the sediments. Most pronounced decreases were measured for planktonically derived hydrocarbon constituents (e.g. pristane and two unsaturated compounds) which are rapidly remineralized at or near the sediment-water interface. Consequently, the amount of each compound measured in deposited sediments is not necessarily a quantitative indication of its initial flux to the sediments. The n-alkanes (C 25,27,29,31). characteristic of terrestrial plant waxes, are the predominant hydrocarbons measured by 4-6 cm depth in these sediments and show reasonably constant net accumulation below this interval. Significant diagenetic alteration of the bulk organic matter contained in the average sediment trap particulate material is also noted through comparison with bottom sediments on the basis of organic C/N and δ 13C measurements. Organic matter elementally similar to marine plankton is preferentially remineralized upon deposition of the sedimentary particulates. The residual organic matter remaining and buried in the bottom sediments closely resembles terrestrial organic matter.

  9. Complete genome of Zhongshania aliphaticivorans SM-2(T), an aliphatic hydrocarbon-degrading bacterium isolated from tidal flat sediment.

    PubMed

    Jia, Baolei; Jeong, Hye Im; Kim, Kyung Hyun; Jeon, Che Ok

    2016-05-20

    Zhongshania aliphaticivorans SM-2(T), a degrader of aliphatic hydrocarbons, is a Gram-negative, rod-shaped, flagellated, facultatively aerobic bacterium. Here, we report the genome sequence of strain SM-2(T), which has a size of 4,204,359bp with 44 tRNAs, 9 rRNAs, and 3664 protein-coding genes. In addition, several genes encoding aliphatic hydrocarbon degraders (alkane 1-monooxygenase, haloalkane dehalogenase, and cytochrome P450) were detected in the genome shedding light on the function of pollutants degradation. PMID:27034022

  10. HOMOGENEOUS CATALYTIC OXIDATION OF HYDROCARBONS IN ALTERNATIVE SOLVENTS

    EPA Science Inventory

    Homogeneous Catalytic Oxidations of Hydrocarbons in Alternative Solvent Systems

    Michael A. Gonzalez* and Thomas M. Becker, Sustainable Technology Division, Office of Research and Development; United States Environmental Protection Agency, 26 West Martin Luther King Drive, ...

  11. Hydrocarbon-solvent based cleaners as replacements for chlorinated and CFC solvents

    SciTech Connect

    Schreiner, J.L.; Berlin, E.P.

    1995-12-31

    Chlorinated and CFC solvents have been used for about 30 years to remove various contaminants from products during the manufacturing process. Among the contaminants being removed are oils, greases, and waxes that have petroleum products as the base. Prior to the advent of the chlorinated solvents petroleum distillates were used for these cleaning operations. Processing improvements over the past 30 years now permit production of higher purity hydrocarbons solvents that can be used as replacements for the chlorinated and CFC solvents being phased out. These hydrocarbon solvents are well suited for removal of the various petroleum based contaminants, as one recalls the old adage {open_quotes}like dissolves like.{close_quotes}

  12. Sources and distribution of aliphatic and polyaromatic hydrocarbons in coastal sediments from the Ushuaia Bay (Tierra del Fuego, Patagonia, Argentina).

    PubMed

    Commendatore, Marta G; Nievas, Marina L; Amin, Oscar; Esteves, José L

    2012-03-01

    The environmental quality of Ushuaia Bay, located at the southernmost tip of South America, is affected by the anthropogenic pressure of Ushuaia city. In this study, levels and sources of hydrocarbons in coastal sediments were assessed. Aliphatic hydrocarbon fractions ranged between 5.5 and 1185.3 μg/g dry weight and PAHs from not detected to 360 ng/g. Aliphatic diagnostic indices, the nalkanes homologous series occurrence, Aliphatic Unresolved Complex Mixtures (AliUCMs), and pristane and phytane isoprenoids indicated a petrogenic input. Some sites showed biogenic features masked by the anthropogenic signature. Particularly in port areas biodegradation processes were evident. PAH ratios showed a mixture of petrogenic and pyrogenic sources. Aliphatic and aromatic UCMs were strongly correlated, reflecting chronic pollution. Three areas were distinguished inside the bay: (1) east, with low hydrocarbons impact; (2) central, where hydrocarbons accumulation was related to source proximity and sediment characteristics; (3) south-west, where sediment characteristics and current circulation favour hydrocarbons accumulation. PMID:22189069

  13. Tuning the structure and solubility of nanojars by peripheral ligand substitution, leading to unprecedented liquid-liquid extraction of the carbonate ion from water into aliphatic solvents.

    PubMed

    Ahmed, Basil M; Calco, Brice; Mezei, Gellert

    2016-05-28

    Nanojars, a novel class of neutral anion-incarcerating agents of the general formula [Cu(II)(OH)(pz)]n (Cun; n = 27-31, pz = pyrazolate anion), efficiently sequester various oxoanions with large hydration energies from water. In this work, we explore whether substituents on the pyrazole ligand interfere with nanojar formation, and whether appropriate substituents could be employed to tune the solubility of nanojars in solvents of interest, such as long-chain aliphatic hydrocarbons (solvent of choice for large-scale liquid-liquid extraction processes) and water. To this end, we conducted a comprehensive study using 40 different pyrazole ligands, with one, two or three substituents in their 3-, 4- and 5-positions. The corresponding nanojars are characterized by single-crystal X-ray diffraction and/or electrospray-ionization mass spectrometry (ESI-MS). The results show that Cun-nanojars with various substituents in the pyrazole 4-position, including long chains, phenyl and CF3 groups, can be obtained. Straight chains are also tolerated at the pyrazole 3-position, and favor the Cu30-nanojar. Homoleptic nanojars, however, could not be obtained with phenyl or CF3 groups. Nevertheless, if used in mixture with the parent non-substituted pyrazole, sterically hindered pyrazoles do form heteroleptic nanojars. With 3,5-disubstituted pyrazoles, only heteroleptic nanojars are accessible. The crystal structure of novel nanojars (Bu4N)2[CO3⊂{Cu30(OH)30(3,5-Me2pz)y(pz)30-y}] (y = 14 and 15) is presented. We find that in contrast to the parent nanojar, which is insoluble in aliphatic solvents and water, nanojars with alkyl substituents are soluble in saturated hydrocarbon solvents, whereas nanojars based on novel pyrazoles, functionalized with oligoether chains, are readily soluble in water. Liquid-liquid extraction of carbonate from water under basic pH is presented for the first time. PMID:27048621

  14. Aliphatic and polycyclic aromatic hydrocarbons characterisation of Coimbra and Oporto PM2.5 urban aerosol

    NASA Astrophysics Data System (ADS)

    Rocha, A. C.; Mirante, F.; Gonçalves, C.; Nunes, T.; Alves, C.; Evtyugina, M.; Kowacz, M.; Pio, C.; Rocha, C.; Vasconcelos, T.

    2009-04-01

    The concentration of organic pollutants in urban areas is mostly due to incomplete combustion from vehicles, industries and domestic heating. Some of these compounds, principally the aliphatic (ALIPH) and polycyclic aromatic hydrocarbons (PAHs) promote harmful effects in human health. The determination of the ALIPH and PAHs concentration levels and their possible emission sources are useful for air quality management and source apportionment studies. In order to estimate and compare the ambient concentrations and establish the main sources of these compounds, the fine fraction of the atmospheric particulate matter (PM2.5) was collected simultaneously in Oporto and Coimbra during summer and winter seasons using a high volume sampler. The organic compounds were extracted from the particulate matter, under reflux with dichloromethane and the total organic extract (TOE) was fractionated by flash chromatography using five different eluents with increasing polarity. The hydrocarbon fractions were analysed by gas chromatography/mass spectrometry (GC/MS). Here we present and discuss the qualitative and quantitative composition of the aliphatic and aromatic fractions present in PM2.5 samples from both cities. The homologous series of C14 to C34 n-alkanes, isoprenoid hydrocarbons (pristane and phytane), PAHs and some petroleum markers have been identified and quantified. With the purpose of identifying the possible sources, various molecular diagnostic ratios were calculated. The global carbon preference index (CPI) closer to the unity, the large concentration of the unresolved complex mixture (UCM) and the presence of PAHs indicate that motor vehicle exhaust was the main emission source of the aliphatic and polycyclic aromatic fractions of Oporto and Coimbra aerosol, especially in the first city. Also, the remarkable presence of petroleum biomarkers such, as hopanes, confirms the previous results. Concentration ratios between PAHs were calculated and used to assign emission

  15. The galactic distribution of aliphatic hydrocarbons in the diffuse interstellar medium

    NASA Technical Reports Server (NTRS)

    Sandford, Scott A.; Pendleton, Yvonne J.; Allamandola, Louis J.

    1995-01-01

    The infrared absorption feature near 2950(exp -1) (3.4 micron), characteristic of dust in the diffuse interstellar medium (ISM), is attributed to C-H stretching vibrations of aliphatic hydrocarbons. We show here that the strength of the band does not scale linearly with visual extinction everywhere, but instead increases more rapidly for objects near the center of the Galaxy, a behavior that parallels that of the Si-O stretching band due to silicate materials in the diffuse ISM. This implies that the grains responsible for the diffuse medium aliphatic C-H and silicate Si-O stretching bands are different from those responsible for much of the observed visual extinction. It also suggests that the distribution of the carbonaceous component of the diffuse ISM is not uniform throughout the Galaxy, but instead may increase in density toward the center of the Galaxy. The similar behavior of the C-H and Si-O stretching bands suggests that these two components may be coupled, perhaps in the form of silicate-core, organic-mantle grains. Several possible models of the distribution of this material are presented and it is demonstrated that the inner parts of the Galaxy has a carrier density that is 5 to 35 times higher than in the local ISM. Depending on the model used, the density of aliphatic material in the local ISM is found to be about 1 to 2 -CH3 groups m(exp -3) and about 2 to 5 -CH2- groups m(exp -3). These densities are consistent with the strengths of the 2955 and 2925 cm(exp -1) (3.4 micron) band being described by the relations A(sub nu)/tau(sub 2955 cm(exp -1)) = 270 +/- 40 and A(sub nu)/tau(sub 2925 cm(exp -1)) = 250 +/- 40 in the local diffuse ISM.

  16. The Galactic Distribution of Aliphatic Hydrocarbons in the Diffuse Interstellar Medium

    NASA Technical Reports Server (NTRS)

    Sandford, Scott A.; Pendleton, Yvonne J.; Allamandola, Louis J.

    1995-01-01

    The infrared absorption feature near 2950/ cm (3.4 microns), characteristic of dust in the diffuse interstellar medium (ISM), is attributed to C-H stretching vibrations of aliphatic hydrocarbons. We show here that the strength of the band does not scale linearly with visual extinction everywhere, but instead increases more rapidly for objects near the center of the Galaxy, a behavior that parallels that of the Si-O stretching band due to silicate materials in the diffuse ISM. This implies that the grains responsible for the diffuse medium aliphatic C-H and silicate Si-O stretching bands are different from those responsible for much of the observed visual extinction. It also suggests that the distribution of the carbonaceous component of the diffuse ISM is not uniform throughout the Galaxy, but instead may increase in density toward the center of the Galaxy. The similar behavior of the C-H and Si-O stretching bands suggests that these two components may be coupled, perhaps in the form of silicate-core, organic-mantle grains. Several possible models of the distribution of this material are presented and it is demonstrated that the inner parts of the Galaxy has a carrier density that is 5 to 35 times higher than in the local ISM. Depending on the model used, the density of aliphatic material in the local ISM is found to be about 1 to 2 -CH3 groups /cc and about 2 to 5 -CH2- groups/cc. These densities are consistent with the strengths of the 2955 and 2925/ cm (3.38 and 3.42 microns) subfeatures (due to -CH3 and -CH2- groups, respectively) within the overall 2950/ cm (3.4 microns) band being described by the relations A(sub upsilon)/tau(sub 2925/cm) = 270 +/- 40 and A(sub upsilon)/tau(sub 2925/cm) = 250 +/- 40 in the local diffuse ISM.

  17. Genetic basis of long-chain aliphatic hydrocarbon biosynthesis in bacteria. Final technical report, July 7, 1981-January 6, 1983

    SciTech Connect

    Kloos, W.E.

    1983-01-01

    A variety of Micrococcus species, some related Arthrobacter, and Pseudomonas maltophilia are among the few bacteria which produce significant quantities of long chain aliphatic hydrocarbons. It was the purpose of this investigation to initiate studies aimed at understanding the genetic basis of aliphatic hydrocarbon production. Results have shown that some strains of several of the Micrococcus species carry plasmids, but they appear not to be associated with hydrocarbon production. Clearly, plasmids are not required for hydrocarbon biosynthesis, as many plasmidless strains produce large quantities of hydrocarbons with normal species-specific profiles. This is the first report on the occurrence of plasmids in Micrococcus species such as M. roseus, M. varians, M. kristinae, M. agilis, M. nishinomiyaensis, and unnamed, nonhuman primate Micrococcus spp. It is also the first report on aliphatic hydrocarbon production in M. agilis and the above nonhuman primate species. Although hydrocarbon production is not specifically under plasmid control, micrococcal plasmids may be able to serve as vectors for cloned hydrocarbon biosynthesis genes and ultimately used in the genetic engineering of this important group of organisms. For this reason, we initiated studies on the nucleotide sequence relationships, restriction enzyme digestion, and marking of several of the more interesting plasmids. Results have indicated that within species some plasmids share considerable nucleotide sequence homology. It is recommended that future investigations on these organisms should focus on unraveling the hydrocarbon biosynthetic pathway(s), isolating and characterizing the various enzymes involved with hydrocarbon biosynthesis, isolating and cloning the various chromosomal genes controlling these enzymes, and exploring genetic transfer (exchange) systems. Expression of micrococcal hydrocarbon genes in other organisms should also be evaluated.

  18. Anaerobic biotransformation of chlorinated aliphatic hydrocarbons: Ugly duckling to beautiful swan

    SciTech Connect

    Parkin, G.F.

    1999-10-01

    For many years anaerobic biological processes were reputed to be more sensitive than aerobic processes to toxic substances such as chlorinated aliphatic hydrocarbons (CAH) and thus a poor choice for treating water containing these compounds. This was especially true for water containing perchloroethylene (PCE) or trichloroethylene (TCE) because vinyl chloride, a human carcinogen, is produced when these two compounds are degraded anaerobically. Aerobic treatment with organisms containing oxygenase enzyme systems, which could fortuitously degrade a wide variety of chlorinated aliphatics (but not PCE), was favored. Recently, however, several enrichments and organisms have been isolated that will convert PCE and TCE into ethene and ethane, as shown by field data. Because of this evidence, anaerobic processes are now considered a significant alternative treatment for CAH contamination. Recent work at the University of Iowa, Iowa City, has focused on the effect of mixtures of CAHs on biotransformation of individual organic compounds and the potential for a combined methanogen-iron (Fe(0)) system to improve CAH bioremediation. At the concentration ranges tested, the presence of a mixture of CAHs seems to decrease rate of transformation of individual organics. However, there are important exceptions; in some cases a mixture of CAHs seems to facilitate transformation of an individual organic compound. Combination of an active methanogenic population with Fe(0) increases the rate and extent of transformation of carbon tetrachloride and chloroform. Results with PCE and 1,1,1-trichloroethane are less clear.

  19. Process for the solvent deasphalting of asphaltene-containing hydrocarbons

    SciTech Connect

    Ikematsu, M.; Honzyo, I.; Sakai, K.

    1985-03-05

    A continuous process for solvent deasphalting asphaltene-containing hydrocarbons which comprises mixing (A) 100 parts by weight of asphaltene-containing hydrocarbons with (B) 0.005-0.5 parts by weight of an amorphous silicon dioxide and/or a silicate compound and also with (C) 5-2000 parts by weight of a solvent such as n-heptane, n-hexane, n-heptane or a mixed n-pentane.n-butanol solvent, to form a mixture which is then allowed to stand still to precipitate and separate the asphaltene therefrom thereby obtaining a deasphalted oil.

  20. Vapor-liquid critical properties of elements and compounds. 6: Unsaturated aliphatic hydrocarbons

    SciTech Connect

    Tsonopoulos, C.; Ambrose, D.

    1996-07-01

    This is part 6 of a series of contributions by the critical properties group of the IUPAC Commission I.2 on Thermodynamics, Subcommittee on Thermodynamic Data. It presents all known experimental data for the critical constants of unsaturated aliphatic hydrocarbons, which have been divided into five families: linear alk-1-enes (10 compounds, C{sub 2} to C{sub 12}); other alkenes (8 compounds, C{sub 4} to C{sub 6}); alkadienes (3 compounds, C{sub 3} to C{sub 6}); terpenes (3 C{sub 10} compounds); and alkynes (3 compounds, C{sub 2} to C{sub 4}). Recommendations are given together with uncertainties. Critical temperatures have been converted to ITS-90.

  1. Inhibition of jet fuel aliphatic hydrocarbon induced toxicity in human epidermal keratinocytes.

    PubMed

    Inman, A O; Monteiro-Riviere, N A; Riviere, J E

    2008-05-01

    Jet propellant (JP)-8, the primary jet fuel used by the U.S. military, consists of hydrocarbon-rich kerosene base commercial jet fuel (Jet-A) plus additives DC1-4A, Stadis 450 and diethylene glycol monomethyl ether. Human epidermal keratinocytes (HEK) were exposed to JP-8, aliphatic hydrocarbon (HC) fuel S-8 and aliphatic HC pentadecane (penta), tetradecane (tetra), tridecane (tri) and undecane (un) for 5 min. Additional studies were conducted with signal transduction pathway blockers parthenolide (P; 3.0 microm), isohelenin (I; 3.0 microm), SB 203580 (SB; 13.3 microm), substance P (SP; 3.0 microm) and recombinant human IL-10 (rHIL-10; 10 ng ml(-1)). In the absence of inhibitors, JP-8 and to a lesser extent un and S-8, had the greatest toxic effect on cell viability and inflammation suggesting, as least in vitro, that synthetic S-8 fuel is less irritating than the currently used JP-8. Each inhibitor significantly (P < 0.05) decreased HEK viability. DMSO, the vehicle for P, I and SB, had a minimal effect on viability. Overall, IL-8 production was suppressed at least 30% after treatment with each inhibitor. Normalizing data relative to control indicate which inhibitors suppress HC-mediated IL-8 to control levels. P was the most effective inhibitor of IL-8 release; IL-8 was significantly decreased after exposure to un, tri, tetra and penta but significantly increased after JP-8 exposure compared with controls. Inhibitors were not effective in suppressing IL-8 release in JP-8 exposures to control levels. This study shows that inhibiting NF-kappa B, which appears to play a role in cytokine production in HC-exposed HEK in vitro, may reduce the inflammatory effect of HC in vivo. PMID:17966119

  2. Characterization of the toxicological hazards of hydrocarbon solvents.

    PubMed

    Mckee, Richard H; Adenuga, M David; Carrillo, Juan-Carlos

    2015-04-01

    Hydrocarbon solvents are liquid hydrocarbon fractions derived from petroleum processing streams, containing only carbon and hydrogen atoms, with carbon numbers ranging from approximately C5-C20 and boiling between approximately 35-370°C. Many of the hydrocarbon solvents have complex and variable compositions with constituents of 4 types, alkanes (normal paraffins, isoparaffins, and cycloparaffins) and aromatics (primarily alkylated one- and two-ring species). Because of the compositional complexity, hydrocarbon solvents are now identified by a nomenclature ("the naming convention") that describes them in terms of physical/chemical properties and compositional elements. Despite the compositional complexity, most hydrocarbon solvent constituents have similar toxicological properties, and the overall toxicological hazards can be characterized in generic terms. To facilitate hazard characterization, the solvents were divided into 9 groups (categories) of substances with similar physical and chemical properties. Hydrocarbon solvents can cause chemical pneumonitis if aspirated into the lung, and those that are volatile can cause acute CNS effects and/or ocular and respiratory irritation at exposure levels exceeding occupational recommendations. Otherwise, there are few toxicologically important effects. The exceptions, n-hexane and naphthalene, have unique toxicological properties, and those solvents containing constituents for which classification is required under the Globally Harmonized System (GHS) are differentiated by the substance names. Toxicological information from studies of representative substances was used to fulfill REACH registration requirements and to satisfy the needs of the OECD High Production Volume (HPV) initiative. As shown in the examples provided, the hazard characterization data can be used for hazard classification and for occupational exposure limit recommendations. PMID:25868376

  3. Physico-chemical properties of binary mixtures of aliphatic and aromatic solvents at 313 K on acoustical data

    NASA Astrophysics Data System (ADS)

    Dahire, S. L.; Morey, Y. C.; Agrawal, P. S.

    2015-12-01

    Density (ρ), viscosity (η), and ultrasonic velocity ( U) of binary mixtures of aliphatic solvents like dimethylformamide (DMF) and dimethylsulfoxide (DMSO) with aromatic solvents viz. chlorobenzene (CB), bromobenzene (BB), and nitrobenzene (NB) have been determined at 313 K. These parameters were used to calculate the adiabatic compressibility (β), intermolecular free length ( L f), molar volume ( V m), and acoustic impedance ( Z). From the experimental data excess molar volume ( V m E ), excess intermolecular free length ( L f E )), excess adiabatic compressibility (βE), and excess acoustic impedance ( Z E) have been computed. The excess values were correlated using Redlich-Kister polynomial equation to obtain their coefficients and standard deviations (σ).

  4. Microbiota associated with the migration and transformation of chlorinated aliphatic hydrocarbons in groundwater.

    PubMed

    Guan, Xiangyu; Liu, Fei; Xie, Yuxuan; Zhu, Lingling; Han, Bin

    2013-08-01

    Pollution of groundwater with chlorinated aliphatic hydrocarbons (CAHs) is a serious environmental problem which is threatening human health. Microorganisms are the major participants in degrading these contaminants. Here, groundwater contaminated for a decade with CAHs was investigated. Numerical simulation and field measurements were used to track and forecast the migration and transformation of the pollutants. The diversity, abundance, and possible activity of groundwater microbial communities at CAH-polluted sites were characterized by molecular approaches. The number of microorganisms was between 5.65E+05 and 1.49E+08 16S rRNA gene clone numbers per liter according to quantitative real-time PCR analysis. In 16S rRNA gene clone libraries constructed from samples along the groundwater flow, eight phyla were detected, and Proteobacteria were dominant (72.8 %). The microbial communities varied with the composition and concentration of pollutants. Meanwhile, toluene monooxygenases and methane monooxygenases capable of degradation of PCE and TCE were detected, demonstrating the major mechanism for PCE and TCE degradation and possibility for in situ remediation by addition of oxygen in this study. PMID:23420483

  5. Degradation kinetics of chlorinated aliphatic hydrocarbons by methane oxidizers naturally-associated with wetland plant roots

    NASA Astrophysics Data System (ADS)

    Powell, C. L.; Goltz, M. N.; Agrawal, A.

    2014-12-01

    Chlorinated aliphatic hydrocarbons (CAHs) are common groundwater contaminants that can be removed from the environment by natural attenuation processes. CAH biodegradation can occur in wetland environments by reductive dechlorination as well as oxidation pathways. In particular, CAH oxidation may occur in vegetated wetlands, by microorganisms that are naturally associated with the roots of wetland plants. The main objective of this study was to evaluate the cometabolic degradation kinetics of the CAHs, cis-1,2-dichloroethene (cisDCE), trichloroethene (TCE), and 1,1,1-trichloroethane (1,1,1TCA), by methane-oxidizing bacteria associated with the roots of a typical wetland plant in soil-free system. Laboratory microcosms with washed live roots investigated aerobic, cometabolic degradation of CAHs by the root-associated methane-oxidizing bacteria at initial aqueous [CH4] ~ 1.9 mg L- 1, and initial aqueous [CAH] ~ 150 μg L- 1; cisDCE and TCE (in the presence of 1,1,1TCA) degraded significantly, with a removal efficiency of approximately 90% and 46%, respectively. 1,1,1TCA degradation was not observed in the presence of active methane oxidizers. The pseudo first-order degradation rate-constants of TCE and cisDCE were 0.12 ± 0.01 and 0.59 ± 0.07 d- 1, respectively, which are comparable to published values. However, their biomass-normalized degradation rate constants obtained in this study were significantly smaller than pure-culture studies, yet they were comparable to values reported for biofilm systems. The study suggests that CAH removal in wetland plant roots may be comparable to processes within biofilms. This has led us to speculate that the active biomass may be on the root surface as a biofilm. The cisDCE and TCE mass losses due to methane oxidizers in this study offer insight into the role of shallow, vegetated wetlands as an environmental sink for such xenobiotic compounds.

  6. Aliphatic and polycyclic aromatic hydrocarbons risk assessment in coastal water and sediments of Khark Island, SW Iran.

    PubMed

    Akhbarizadeh, Razegheh; Moore, Farid; Keshavarzi, Behnam; Moeinpour, Alireza

    2016-07-15

    The potential sources and ecotoxicological risks of 26 aliphatic hydrocarbons (AHs), 16 polycyclic aromatic hydrocarbons (PAHs) and total petroleum hydrocarbons (TPHs) were investigated in coastal water and sediments of Khark Island, SW Iran. The major sources of the contamination were petroleum and petroleum combustion based on the PCA analysis and diagnostic indices of AHs and PAHs, and also ring classification of PAHs. The ecological risk of both individual and multiple PAHs was quite low in sediments compared with screening benchmarks. Likewise, the low concentration of TEQ, MEQ and TEQ(carc) of sediments suggest low toxicity of PAHs in the study area. However, environmental control is recommended to reduce the pollution burden of PAHs in seawater. The human health risk assessment for PAHs through dermal adsorption indicated that the possibility of negative adverse effects of PAHs in sediments is rare but swimming in the vicinity of industrial facilities should be done cautiously. PMID:27207022

  7. Aliphatic and aromatic hydrocarbons in marine biota and coastal sediments from the Gulf and the Gulf of Oman.

    PubMed

    Tolosa, Imma; de Mora, Stephen J; Fowler, Scott W; Villeneuve, Jean-Pierre; Bartocci, Jean; Cattini, Chantal

    2005-12-01

    The composition and spatial distribution of aliphatic and polycyclic aromatic hydrocarbons (PAHs) were investigated in biota and coastal sediments from four countries surrounding the Gulf (Bahrain, Qatar, United Arab Emirates and Oman). The levels of total petroleum hydrocarbons (TPH), aliphatic unresolved mixture and PAHs in sediments and biota were relatively low compared to world-wide locations reported to be chronically contaminated by oil. Only in the case of the sediments collected near the BAPCO oil refinery in Bahrain, having concentrations of 779 microg g(-1) total petroleum hydrocarbon equivalents and 6.6 microg g(-1) Sigma PAHs, can they be categorized as chronically contaminated. Some evidence of oil contamination was also apparent in sediments and bivalves around Akkah Head and Abu Dhabi in the UAE, and near Mirbat in Oman. Contaminant patterns in sediments and biota indicated that the PAHs were mainly from fossil sources, with the exception of the high PAH concentrations in sediments near the BAPCO refinery that contained substantial concentrations of carcinogenic PAH combustion products. PMID:16038948

  8. Degradation kinetics of chlorinated aliphatic hydrocarbons by methane oxidizers naturally-associated with wetland plant roots.

    PubMed

    Powell, C L; Goltz, M N; Agrawal, A

    2014-12-01

    Chlorinated aliphatic hydrocarbons (CAHs) are common groundwater contaminants that can be removed from the environment by natural attenuation processes. CAH biodegradation can occur in wetland environments by reductive dechlorination as well as oxidation pathways. In particular, CAH oxidation may occur in vegetated wetlands, by microorganisms that are naturally associated with the roots of wetland plants. The main objective of this study was to evaluate the cometabolic degradation kinetics of the CAHs, cis-1,2-dichloroethene (cisDCE), trichloroethene (TCE), and 1,1,1-trichloroethane (1,1,1TCA), by methane-oxidizing bacteria associated with the roots of a typical wetland plant in soil-free system. Laboratory microcosms with washed live roots investigated aerobic, cometabolic degradation of CAHs by the root-associated methane-oxidizing bacteria at initial aqueous [CH4] ~1.9mgL(-1), and initial aqueous [CAH] ~150μgL(-1); cisDCE and TCE (in the presence of 1,1,1TCA) degraded significantly, with a removal efficiency of approximately 90% and 46%, respectively. 1,1,1TCA degradation was not observed in the presence of active methane oxidizers. The pseudo first-order degradation rate-constants of TCE and cisDCE were 0.12±0.01 and 0.59±0.07d(-1), respectively, which are comparable to published values. However, their biomass-normalized degradation rate constants obtained in this study were significantly smaller than pure-culture studies, yet they were comparable to values reported for biofilm systems. The study suggests that CAH removal in wetland plant roots may be comparable to processes within biofilms. This has led us to speculate that the active biomass may be on the root surface as a biofilm. The cisDCE and TCE mass losses due to methane oxidizers in this study offer insight into the role of shallow, vegetated wetlands as an environmental sink for such xenobiotic compounds. PMID:25444117

  9. Sequential accelerated solvent extraction of polycyclic aromatic hydrocarbons with different solvents: performance and implication.

    PubMed

    Ma, Xiaoxuan; Ran, Yong; Gong, Jian; Chen, Diyun

    2010-01-01

    Sixteen USEPA priority polycyclic aromatic hydrocarbons (PAHs) extracted by Soxhlet extraction (S-PAHs) with dichloromethane and routine accelerated solvent extraction (A-PAHs) with 1:1 toluene/methanol, respectively, were investigated in 24 soil samples from two cities in the center of the Pearl River Delta, South China. Polycyclic aromatic hydrocarbons, methylphenanthrene and perylene, in two soils, two sediments, and an immature oil shale were also sequentially extracted by accelerated solvent extraction (ASE) with each of four different organic solvents for three times. The A-PAHs' concentrations are 2.41 times the S-PAHs' concentrations. For sequential three ASEs, PAHs in the first extract account for 56 to 67% of their total concentrations in the sequential three extractions and toluene displays the best extraction performance among the four solvents. Diagnostic ratios of PAHs in Soxhlet extraction, routine ASE, and sequential ASE with each solvent for a given sample are very similar, suggesting their identical petrogenic and pyrogenic sources in the soils and sediments. But the PAH ratios for the shale have an obvious petrogenic origin. The perylene/5-ring PAH ratios indicate a diagenetic source, especially in the shale and sediments. The correlation analysis shows that A-PAHs/S-PAHs is better associated with the contents of total organic carbon (TOC) than those of black carbon (BC). The above results indicate the significant petrogenic origin of PAHs and the important effect of organic matter on their extraction and distribution in the investigated field soils/sediments. PMID:21284305

  10. Efficient organic solar cells processed from hydrocarbon solvents

    NASA Astrophysics Data System (ADS)

    Zhao, Jingbo; Li, Yunke; Yang, Guofang; Jiang, Kui; Lin, Haoran; Ade, Harald; Ma, Wei; Yan, He

    2016-02-01

    Organic solar cells have desirable properties, including low cost of materials, high-throughput roll-to-roll production, mechanical flexibility and light weight. However, all top-performance devices are at present processed using halogenated solvents, which are environmentally hazardous and would thus require expensive mitigation to contain the hazards. Attempts to process organic solar cells from non-halogenated solvents lead to inferior performance. Overcoming this hurdle, here we present a hydrocarbon-based processing system that is not only more environmentally friendly but also yields cells with power conversion efficiencies of up to 11.7%. Our processing system incorporates the synergistic effects of a hydrocarbon solvent, a novel additive, a suitable choice of polymer side chain, and strong temperature-dependent aggregation of the donor polymer. Our results not only demonstrate a method of producing active layers of organic solar cells in an environmentally friendly way, but also provide important scientific insights that will facilitate further improvement of the morphology and performance of organic solar cells.

  11. Forensic investigation of aliphatic hydrocarbons in the sediments from selected mangrove ecosystems in the west coast of Peninsular Malaysia.

    PubMed

    Vaezzadeh, Vahab; Zakaria, Mohamad Pauzi; Shau-Hwai, Aileen Tan; Ibrahim, Zelina Zaiton; Mustafa, Shuhaimi; Abootalebi-Jahromi, Fatemeh; Masood, Najat; Magam, Sami Mohsen; Alkhadher, Sadeq Abdullah Abdo

    2015-11-15

    Peninsular Malaysia has gone through fast development during recent decades resulting in the release of large amounts of petroleum and its products into the environment. Aliphatic hydrocarbons are one of the major components of petroleum. Surface sediment samples were collected from five rivers along the west coast of Peninsular Malaysia and analyzed for aliphatic hydrocarbons. The total concentrations of C10 to C36 n-alkanes ranged from 27,945 to 254,463ng·g(-1)dry weight (dw). Evaluation of various n-alkane indices such as carbon preference index (CPI; 0.35 to 3.10) and average chain length (ACL; 26.74 to 29.23) of C25 to C33 n-alkanes indicated a predominance of petrogenic source n-alkanes in the lower parts of the Rivers, while biogenic origin n-alkanes from vascular plants are more predominant in the upper parts, especially in less polluted areas. Petrogenic sources of n-alkanes are predominantly heavy and degraded oil versus fresh oil inputs. PMID:26323864

  12. Aliphatic hydrocarbon spectra by helium ionization mass spectrometry (HIMS) on a modified atmospheric-pressure source designed for electrospray ionization.

    PubMed

    Yang, Zhihua; Attygalle, Athula B

    2011-08-01

    Chemical-ionization techniques that use metastable species to ionize analytes traditionally use a flat pin or a sharp solid needle onto which the high potential needed to generate the discharge plasma is applied. We report here that direct analysis of samples containing volatile and semivolatile compounds, including saturated and unsaturated aliphatic hydrocarbons, can be achieved on any electrospray-ionization mass spectrometer by passing helium though the sample delivery metal capillary held at a high potential. In the helium plasma ionization source (HPIS) described here, the typical helium flow required (about 20-30 mL/min), was significantly lower than that needed for other helium-ionization sources. By this procedure, positive ions were generated by nominal hydride ion removal from molecules emanating from heated saturated hydrocarbons as large as tetratetracontane (C(44)H(90)), at capillary voltages ranging from 2.0 to 4.0 kV. Unsaturated hydrocarbons, on the other hand, underwent facile protonation under much lower capillary voltages (0.9 to 2.0 kV). Although saturated and monounsaturated hydrocarbons bearing the same number of carbon atoms generate ions of the same m/z ratio, a gas-phase deuterium exchange method is described to ascertain the identity of these isomeric ions originating from either protonation or hydride abstraction mechanisms. Moreover, mass spectrometric results obtained by exposing unsaturated hydrocarbons to D(2)O vapor in an HPIS-MS instrument confirmed that the proton donor for ionization of unsaturated hydrocarbons is protonated water. PMID:21953194

  13. Oxidation of Aliphatic Alcohols by Using Precious Metals Supported on Hydrotalcite under Solvent- and Base-Free Conditions.

    PubMed

    He, Yufei; Feng, Junting; Brett, Gemma L; Liu, Yanan; Miedziak, Peter J; Edwards, Jennifer K; Knight, David W; Li, Dianqing; Hutchings, Graham J

    2015-10-12

    Precious metal nanoparticles supported on magnesium-aluminum hydrotalcite (HT), TiO2 , and MgO were prepared by sol immobilization and assessed for the catalytic oxidation of octanol, which is a relatively unreactive aliphatic alcohol, with molecular oxygen as the oxidant under solvent- and base-free conditions. Compared with the TiO2 - and MgO-supported catalysts, platinum HT gave the highest activity and selectivity towards the aldehyde. The turnover number achieved for the platinum HT catalyst was >3700 after 180 min under mild reaction conditions. Moreover, the results for the oxidation of different substrates indicate that a specific interaction of octanal with the platinum HT catalyst could lead to deactivation of the catalyst. PMID:26337897

  14. Preliminary chemical analysis and biological testing of materials from the HRI catalytic two-stage liquefaction (CTSL) process. [Aliphatic hydrocarbons

    SciTech Connect

    Later, D.W.; Wilson, B.W.

    1985-01-01

    Coal-derived materials from experimental runs of Hydrocarbon Research Incorporated's (HRI) catalytic two-stage liquefaction (CTSL) process were chemically characterized and screened for microbial mutagenicity. This process differs from two-stage coal liquefaction processes in that catalyst is used in both stages. Samples from both the first and second stages were class-fractionated by alumina adsorption chromatography. The fractions were analyzed by capillary column gas chromatography; gas chromatography/mass spectrometry; direct probe, low voltage mass spectrometry; and proton nuclear magnetic resonance spectrometry. Mutagenicity assays were performed with the crude and class fractions in Salmonella typhimurium, TA98. Preliminary results of chemical analyses indicate that >80% CTSL materials from both process stages were aliphatic hydrocarbon and polynuclear aromatic hydrocarbon (PAH) compounds. Furthermore, the gross and specific chemical composition of process materials from the first stage were very similar to those of the second stage. In general, the unfractionated materials were only slightly active in the TA98 mutagenicity assay. Like other coal liquefaction materials investigated in this laboratory, the nitrogen-containing polycyclic aromatic compound (N-PAC) class fractions were responsible for the bulk of the mutagenic activity of the crudes. Finally, it was shown that this activity correlated with the presence of amino-PAH. 20 figures, 9 tables.

  15. In-Situ Heating Decrease Kinetics of Aliphatic Hydrocarbons in Tagish Lake Meteorite by Micro-FTIR

    NASA Technical Reports Server (NTRS)

    Kebukawa, Y.; Nakashima, S.; Zolensky, M. E.

    2005-01-01

    Carbonaceous chondrites are known to contain up to 3wt.% C, the major part of which corresponds to a macromolecular organic fraction. Chondritic organic matter is based on small aromatic units, cross-linked by short aliphatic chains rather than large clusters of polyaromatic structures. Two main characteristic features of those organics measured by FTIR are: (1) an equivalent intensity of the asymmetric stretching mode absorptions for CH3 (2960/cm) and CH2 (2920/cm) and (2) a lack of aromatic CH-stretching mode (3040/cm). Tagish Lake is a new type of water- and carbon-rich type 2 carbonaceous chondrite. Its total carbon content is approx. 5 wt%, of which the organic carbon content reaches approx. 1.3 wt%. Tagish Lake may have never experienced temperatures higher than 120 C after formation of organics based on the disappearance of infrared (IR) organic peaks in step heating experiments. Here we report in-situ kinetic heating experiments of organics in Tagish Lake by micro-FTIR to characterize the nature of aliphatic hydrocarbons and their thermal stabilities.

  16. Aliphatic Hydrocarbons and Fatty Acids of Some Marine and Freshwater Microorganisms

    PubMed Central

    Oró, J.; Tornabene, T. G.; Nooner, D. W.; Gelpi, E.

    1967-01-01

    Gas chromatography and combined gas chromatography-mass spectrometry have been used to study the fatty acids and hydrocarbons of a bacterium from the Pacific Ocean, Vibrio marinus, a freshwater blue-green alga, Anacystis nidulans, and algal mat communities from the Gulf of Mexico. Both types of microorganisms (bacteria and algae) showed relatively simple hydrocarbon and fatty acid patterns, the hydrocarbons predominating in the region of C-17 and the fatty acids in the range of C-14 to C-18. The patterns of V. marinus were more comparable to those of the algal populations than to patterns reported for other bacteria. An incomplete correlation between fatty acids and hydrocarbons in both types of organisms was observed, making it difficult to accept the concept that the biosynthesis of hydrocarbons follows a simple fatty acid decarboxylation process. PMID:6025301

  17. Porphyrin-Embedded Silicate Materials for Detection of Hydrocarbon Solvents

    PubMed Central

    Johnson, Brandy J.; Anderson, Nicole E.; Charles, Paul T.; Malanoski, Anthony P.; Melde, Brian J.; Nasir, Mansoor; Deschamps, Jeffrey R.

    2011-01-01

    The development of porphyrin-embedded mesoporous organosilicate materials for application to the detection of volatile hydrocarbon solvents is described. Design of the receptor and optical indicator construct begins with parallel selection of the porphyrin indicator and design of the mesoporous sorbent. For the porphyrin indicator, high binding affinity and strong changes in spectrophotometric character upon target interaction are desired. The sorbent should provide high target binding capacity and rapid binding kinetics. A number of porphyrin/metalloporphyrin variants and organosilicate sorbents were evaluated to determine the characteristics of their interaction with the targets, benzene, toluene, and hexane. The selected porphyrin candidates were covalently immobilized within a benzene-bridged sorbent. This construct was applied to the detection of targets using both fluorescence- and reflectance-based protocols. The use of red, green, and blue (RGB) color values from the constructs in a highly simplified detection scheme is described. PMID:22346609

  18. 40 CFR Table 2c to Subpart E of... - Reactivity Factors for Aromatic Hydrocarbon Solvent Mixtures

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Reactivity Factors for Aromatic Hydrocarbon Solvent Mixtures 2C Table 2C to Subpart E of Part 59 Protection of Environment ENVIRONMENTAL... Hydrocarbon Solvent Mixtures Bin Boiling range (degrees F) Criteria Reactivityfactor 21 280-290...

  19. 40 CFR Table 2c to Subpart E of... - Reactivity Factors for Aromatic Hydrocarbon Solvent Mixtures

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 6 2014-07-01 2014-07-01 false Reactivity Factors for Aromatic Hydrocarbon Solvent Mixtures 2C Table 2C to Subpart E of Part 59 Protection of Environment ENVIRONMENTAL... Hydrocarbon Solvent Mixtures Bin Boiling range(degrees F) Criteria Reactivityfactor (g O3/g VOC) 21...

  20. 40 CFR Table 2c to Subpart E of... - Reactivity Factors for Aromatic Hydrocarbon Solvent Mixtures

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 6 2013-07-01 2013-07-01 false Reactivity Factors for Aromatic Hydrocarbon Solvent Mixtures 2C Table 2C to Subpart E of Part 59 Protection of Environment ENVIRONMENTAL... Hydrocarbon Solvent Mixtures Bin Boiling range(degrees F) Criteria Reactivityfactor (g O3/g VOC) 21...

  1. 40 CFR Table 2c to Subpart E of... - Reactivity Factors for Aromatic Hydrocarbon Solvent Mixtures

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 5 2011-07-01 2011-07-01 false Reactivity Factors for Aromatic Hydrocarbon Solvent Mixtures 2C Table 2C to Subpart E of Part 59 Protection of Environment ENVIRONMENTAL... Hydrocarbon Solvent Mixtures Bin Boiling range (degrees F) Criteria Reactivityfactor 21 280-290...

  2. 40 CFR Table 2c to Subpart E of... - Reactivity Factors for Aromatic Hydrocarbon Solvent Mixtures

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 6 2012-07-01 2012-07-01 false Reactivity Factors for Aromatic Hydrocarbon Solvent Mixtures 2C Table 2C to Subpart E of Part 59 Protection of Environment ENVIRONMENTAL... Hydrocarbon Solvent Mixtures Bin Boiling range(degrees F) Criteria Reactivityfactor (g O3/g VOC) 21...

  3. Solubility and Spectroscopy of Unsaturated Hydrocarbons in Cryogenic Solvents

    NASA Astrophysics Data System (ADS)

    Diez Y Riega, Maria Helena

    The exploration of Saturn's moon, Titan has revealed an atmosphere rich in nitrogen as in Earth, and has established the presence of gaseous methane. Data from the Cassini-Huygens mission have shown the existence of liquid bodies of methane and ethane, such as lakes and rivers with geological structures similar to Earth, with bays, islands, and channels. Moreover, the Cassini-Huygens mission has shown strong evidence that Titan's surface and atmosphere have an active hydrological cycle alike, with condensed hydrocarbons instead. Although identification of chemical species is hard, many organic molecules have been detected in the atmosphere, and in icy form on the surface. Spectroscopic properties and solubility of many unsaturated hydrocarbons dissolved in liquid methane and ethane is unknown. Thus, in this work, vibrational spectroscopy in the IR-NIR-Vis of small organic molecules such as benzene, ethene, 2-methyl-1,3-butadiene (isoprene), and formaldehyde dissolved in liquid ethane, rare gases, and nitrogen under Titan's conditions (low temperatures, and concentrations in the order of 10-4 mole fraction) are presented. Our studies indicate that the presence of the solvent interacting with the solute produces frequency shift and change in the linewidth from that of the gas phase. Additionally, solubilities of unsaturated hydrocarbons in liquid ethane and liquid argon have been meassured. In order to study the weak fifth CH vibrational overtone of the selected molecules, Fourier Transform spectroscopy is not sensible enough. Thermal Lens spectroscopy has been found to be a very sensitive technique, good for detecting samples of low concentration in transparent solutions. In addition to the traditional double-beam configuration, whose absorption process is carried out with one photon absorption, we have also developed a new triple-beam thermal lens apparatus in a collinear configuration, in order to enhance the thermal lens signal upon two photon absorption.

  4. Polycyclic aromatic hydrocarbons, aliphatic hydrocarbons, trace elements and monooxygenase activity in birds nesting on the North Platte River, Casper, Wyoming, USA

    USGS Publications Warehouse

    Custer, T.W.; Custer, Christine M.; Dickerson, K.; Allen, K.; Melancon, M.J.; Schmidt, L.J.

    2001-01-01

    Tree swallow (Tachycineta bicolor) and house wren (Troglodytes aedon) eggs and chicks were collected near a refinery site on the North Platte River, Casper, Wyoming, USA and at a reference site 10 km upstream. Total polycylic aromatic hydrocarbon (PAH) concentrations in swallow and wren chicks were higher at the refinery site than at the reference site. Polycylic aromatic hydrocarbon concentrations in sediment and chick dietary samples were consistent with these findings. The general lack of methylated PAHs in sediment, diet, and bird carcasses suggested that the PAHs were derived from combustion and not from petroleum. The predominance of odd numbered aliphatic hydrocarbons and the low ratios (≤ 0.25) of pristane: n-C17 and phytane: n-C18 in chick and diet samples also suggested that swallow and wren chicks were not being chronically exposed to petroleum. Mean ethoxyresorufin-O-dealkylase and benzyloxyresorufin-O-dealkylase activities in tree swallow livers averaged nine times higher at the refinery site than at the reference site and were probably induced by exposure to PAHs. Trace element concentrations in eggs and livers of swallows and wrens were similar or greater at the reference site than at the refinery site. Selenium, strontium, and boron concentrations were elevated in eggs and livers of swallows and wrens at both the refinery and reference sites.

  5. Polycyclic aromatic hydrocarbons, aliphatic hydrocarbons, trace elements, and monooxygenase activity in birds nesting on the North Platte River, Casper, Wyoming, USA.

    PubMed

    Custer, T W; Custer, C M; Dickerson, K; Allen, K; Melancon, M J; Schmidt, L J

    2001-03-01

    Tree swallow (Tachycineta bicolor) and house wren (Troglodytes aedon) eggs and chicks were collected near a refinery site on the North Platte River, Casper. Wyoming, USA and at a reference site 10 km upstream. Total polycyclic aromatic hydrocarbon (PAH) concentrations in swallow and wren chicks were higher at the refinery site than at the reference site. Polycyclic aromatic hydrocarbon concentrations in sediment and chick dietary samples were consistent with these findings. The general lack of methylated PAHs in sediment, diet, and bird carcasses suggested that the PAHs were derived from combustion and not from petroleum. The predominance of odd-numbered aliphatic hydrocarbons and the low ratios (< or =0.25) of pristane:n-C17 and phytane:n-C18 in chick and diet samples also suggested that swallow and wren chicks were not being chronically exposed to petroleum. Mean ethoxyresorufin-O-dealkylase and benzyloxyresorufin-O-dealkylase activities in tree swallow livers averaged nine times higher at the refinery site than at the reference site and were probably induced by exposure to PAHs. Trace element concentrations in eggs and livers of swallows and wrens were similar or greater at the reference site than at the refinery site. Selenium, strontium, and boron concentrations were elevated in eggs and livers of swallows and wrens at both the refinery and reference sites. PMID:11349865

  6. A comparison of sedimentary aliphatic hydrocarbon distribution between the southern Okinawa Trough and a nearby river with high sediment discharge

    NASA Astrophysics Data System (ADS)

    Jeng, Woei-Lih; Huh, Chih-An

    2006-01-01

    Twelve surface sediments from the southern Okinawa Trough (OT) and nine surface sediments from a nearby river, the Lanyang River (LR), with high sediment discharge were analyzed for comparison of their aliphatic hydrocarbon distributions. Performing cluster analysis on all hydrocarbon data of LR and OT sediments showed that the two areas had a similarity level of only 0.15, meaning that they were quite dissimilar. The average ratio of terrigenous to aquatic n-alkanes was 0.99 for LR sediments and 9.64 for OT sediments, indicating that the concentrations of n-alkanes in LR and OT sediments were quite different. Furthermore, the mean pristane/phytane ratios for LR and OT sediments were 1.01 and 2.57, respectively; the difference between them was significant (Student's t test, at the 99% significance level). The carbon preference index (CPI) of C 25-C 33n-alkanes averaged 3.26 (range 2.16-4.59) for LR sediments and 2.92 (range 2.35-5.24) for OT sediments; no significant difference was found between the two CPI averages (Student's t test, at the 99% confidence level). However, higher plant n-alkanes generally maximized at C 29 for LR sediments, but maximized at C 31 for all OT sediments, strongly indicating significant differences in the origins of the hydrocarbons in these two areas. All present results appear to suggest that LR sediments are not a major hydrocarbon source for OT sediments. In addition, there was no positive, linear correlation between diploptene (hop-22(29)-ene) and terrestrial higher plant n-alkanes for LR and OT sediments.

  7. Distributions and sources of petroleum, aliphatic hydrocarbons and polycyclic aromatic hydrocarbons (PAHs) in surface sediments from Bohai Bay and its adjacent river, China.

    PubMed

    Wang, Min; Wang, Chuanyuan; Hu, Xiaoke; Zhang, Haijiang; He, Shijie; Lv, Shuangyan

    2015-01-15

    Surface sediment samples from Bohai Bay and its adjacent river, China, were analyzed for aliphatic hydrocarbon, PAHs and biomarkers in order to determine the distribution, composition and source of organic matter in a coastal environment. Results suggested that the input of organic matter from anthropogenic activities has a more significant influence on its distribution than that from natural processes. Petroleum contamination, mainly from offshore oil exploration and discharge of pollutants from rivers, was the main source of n-alkanes. PAHs were mostly of pyrogenic origin; while some sites in Yellow River Estuary were derived mainly from the petrogenic sources. The toxic assessment suggested that the PAHs in surface sediments will not cause immediately adverse biological effects in sediments from Bohai Bay and its adjacent river, China. PMID:25499964

  8. High anodic stability of a new electrolyte solvent: Unsymmetric noncyclic aliphatic sulfone

    SciTech Connect

    Xu, K.; Angell, C.A.

    1998-04-01

    To improve the anodic stability of ambient temperature electrolytes, a nontoxic solvent based on the sulfone polar group has been synthesized and evaluated i the presence of high potential cathode materials. Solutions of high stability salts such as LiClO{sub 4} and Li made in this solvent, withstand 5.8 V vs. Li{sup +}/Li before onset of oxidation, defined by a stringent criterion, even in the presence of high surface area electrodes such as activated charcoal on Pt. Reversible Li deposition and stripping is observed at negative potentials. This means not only that a wide range of overcharge protection is available for high voltage cathodes in current use, but also that exotic cathodes accepting electrons up to 5.5 V from Li{sup +}/Li may now be incorporated in rechargeable lithium cells.

  9. Assessment of degradation potential of aliphatic hydrocarbons by autochthonous filamentous fungi from a historically polluted clay soil.

    PubMed

    Covino, Stefano; D'Annibale, Alessandro; Stazi, Silvia Rita; Cajthaml, Tomas; Čvančarová, Monika; Stella, Tatiana; Petruccioli, Maurizio

    2015-02-01

    The present work was aimed at isolating and identifying the main members of the mycobiota of a clay soil historically contaminated by mid- and long-chain aliphatic hydrocarbons (AH) and to subsequently assess their hydrocarbon-degrading ability. All the isolates were Ascomycetes and, among them, the most interesting was Pseudoallescheria sp. 18A, which displayed both the ability to use AH as the sole carbon source and to profusely colonize a wheat straw:poplar wood chip (70:30, w/w) lignocellulosic mixture (LM) selected as the amendment for subsequent soil remediation microcosms. After a 60 d mycoaugmentation with Pseudoallescheria sp. of the aforementioned soil, mixed with the sterile LM (5:1 mass ratio), a 79.7% AH reduction and a significant detoxification, inferred by a drop in mortality of Folsomia candida from 90 to 24%, were observed. However, similar degradation and detoxification outcomes were found in the non-inoculated incubation control soil that had been amended with the sterile LM. This was due to the biostimulation exerted by the amendment on the resident microbiota, fungi in particular, the activity and density of which were low, instead, in the non-amended incubation control soil. PMID:25461057

  10. Controlled oxidation of aliphatic CH bonds in metallo-monooxygenases: mechanistic insights derived from studies on deuterated and fluorinated hydrocarbons.

    PubMed

    Chen, Yao-Sheng; Luo, Wen-I; Yang, Chung-Ling; Tu, Yi-Jung; Chang, Chun-Wei; Chiang, Chih-Hsiang; Chang, Chi-Yao; Chan, Sunney I; Yu, Steve S-F

    2014-05-01

    The control over the regio- and/or stereo-selective aliphatic CH oxidation by metalloenzymes is of great interest to scientists. Typically, these enzymes invoke host-guest chemistry to sequester the substrates within the protein pockets, exploiting sizes, shapes and specific interactions such as hydrogen-bonding, electrostatic forces and/or van der Waals interactions to control the substrate specificity, regio-specificity and stereo-selectivity. Over the years, we have developed a series of deuterated and fluorinated variants of these hydrocarbon substrates as probes to gain insights into the controlled CH oxidations of hydrocarbons facilitated by these enzymes. In this review, we illustrate the application of these designed probes in the study of three monooxygenases: (i) the particulate methane monooxygenase (pMMO) from Methylococcus capsulatus (Bath), which oxidizes straight-chain C1-C5 alkanes and alkenes to form their corresponding 2-alcohols and epoxides, respectively; (ii) the recombinant alkane hydroxylase (AlkB) from Pseudomonas putida GPo1, which oxidizes the primary CH bonds of C5-C12 linear alkanes; and (iii) the recombinant cytochrome P450 from Bacillus megaterium, which oxidizes C12-C20 fatty acids at the ω-1, ω-2 or ω-3 CH positions. PMID:24629413

  11. Frequency of genes in aromatic and aliphatic hydrocarbon biodegradation pathways within bacterial populations from Alaskan sediments.

    PubMed

    Sotsky, J B; Greer, C W; Atlas, R M

    1994-11-01

    A significant proportion of the naturally occurring hydrocarbon-degrading populations within Alaskan sediments affected by the Exxon Valdez oil spill had both the xylE and alkB genes and could convert hexadecane and naphthalene to carbon dioxide; a greater proportion of the population had xylE than had alkB, reflecting the composition of the residual oil at the time of sampling; nearly equal populations with xylE alone, alkB alone, and xylE + alkB genes together were found after exposure to fresh crude oil; populations with xylE lacking alkB increased after enrichment on naphthalene. Thus, the genotypes of hydrocarbon-degrading populations reflected the composition of the hydrocarbons to which they were exposed. PMID:7804909

  12. Environmental degradation of polluting aromatic and aliphatic hydrocarbons: a case study.

    PubMed

    Osuji, Leo C; Ozioma, Achugasim

    2007-03-01

    Oil extracts of Ukpeliede spill samples from Niger Delta (Nigeria) were analyzed by gas chromatography. The amount of polycyclic aromatic hydrocarbons (PAHs), especially the lower-molecular-weight naphthene, fluorine, phenathrene, pyrene, and benzo[a]anthracene, decreased within the sampling intervals of 2 months and 5 months. There was a predominance of three-to-six-ring PAHs over the two-ring PAHs. There was marked disappearance of n-C8 to n-C11 hydrocarbon fractions and the acyclic isoprenoids (pristane and phytane). The depletion of these molecules within the two sampling intervals suggests the possible attenuation of hydrocarbons as a result of the environmental modification within the set interval. PMID:17372944

  13. Distribution and fate of aliphatic and aromatic hydrocarbons in Antarctic fauna and environment

    NASA Astrophysics Data System (ADS)

    Platt, H. M.; Mackie, P. R.

    1980-03-01

    With the depletion of oil resources in more accessible areas, those of remote regions are being considered or indeed are now being exploited. In many of these regions, especially the polar ones, little is known of the effects such exploitation will have on the environment. But it is known that the ecosystems are often subject to great stress by natural climatic conditions and additional burdens imposed by man may have catastrophic environmental effects. South Georgia, a sub-Antarctic island, has a history of industrial activity mainly concerned with whaling operations that peaked around 1925-1935 but has since declined to virtually nothing. Studies of the ecology of the area provided a unique opportunity to assess the long-term effects that such activities had on the ecosystem. Off the whaling stations a considerable amount of waste material, including fuel oil, was released into the bays and inevitably some of this material was deposited in the sediments. Chemical evidence in the form of both paraffinic and aromatic hydrocarbons still persists in the sediments. The implications of this persistence in relation to the possible influence of the low temperature conditions are discussed. The superficial sediments, marine biota and terrestrial plants, which since 1965 have returned virtually to a pristine state, contain hydrocarbons essentially similar to unpolluted areas around the coast of Britain. Relatively high levels of carcinogenic/mutagenic polynuclear aromatic hydrocarbons in surface sediments suggests a world-wide background of abiogenic hydrocarbons probably disseminated by airborne transport. This appears to indicate that contamination reaches even remote parts of the world in relatively undiminished quantities.

  14. Process for separating a fluid feed mixture containing hydrocarbon oil and an organic solvent

    SciTech Connect

    Bitter, J.G.A.; Haan, J.P.

    1989-03-07

    This patent describes a process for separating a fluid feed mixture containing a hydrocarbon lubricating base oil and an organic solvent selected from furfural and mixture of toluene and methyl ethyl ketone which process comprises subjecting the fluid feed mixture to reverse osmosis in a reverse osmosis zone with a membrane comprising a layer of a silicone polymer. The process provides a retentate stream having an organic solvent content higher than the feed mixture, and a permeate stream having an organic solvent content less than the amount of solvent in the feed mixture, and permits recovering hydrocarbon oil from the permeate stream.

  15. 3.4 Micron Emission from Aliphatic Hydrocarbons in Proto-Planetary Nebulae

    NASA Astrophysics Data System (ADS)

    Hrivnak, B. J.; Kwok, S.; Geballe, T. R.

    2002-12-01

    A family of infrared emission features at 3.3, 6.2, 7.7, 8.6, 11.3 μ m are seen in a variety of objects with strong uv radiation fields. These features are attributed to stretching and bending modes of aromatic compounds. An aliphatic feature has been detected at 3.4 μ m in some of these same objects. Proto-planetary nebulae (PPNs) are in a short-lived stage of evolution between the asymptotic giant branch and planetary nebula (PN) phases. It is observed that in this transitional stage, the strengths of some of these infrared emission features differ from those seen in PNs. In particular, the 3.4 μ m feature, which is usually much weaker than the 3.3 μ m feature, is of comparable strength in some PPNs. To better understand the properties of these features, we carried out medium-resolution (R ~2000) spectroscopy of a sample of PPNs in the 3 μ m region using the NIRSPEC spectrograph on the Keck II telescope. Eight PPNs were observed. These resulted in the first detection of the 3.4 μ m feature in two objects and possible detections in two others and the first detection of the 3.3 μ m feature in two other objects. We will discuss what has been learned from the observations of the 3.4 μ m feature and review the evidence for a correlation of the ratio of the 3.4 to 3.3 μ m features with spectral type. These observations were carried out in the service observing mode as part of a program of limited access to Keck provided to the Gemini Observatory community. This work was funded in part by grants to BJH from the NSF and to SK by NSERC.

  16. Patterns and sources of particle-phase aliphatic and polycyclic aromatic hydrocarbons in urban and rural sites of western Greece

    NASA Astrophysics Data System (ADS)

    Kalaitzoglou, Maria; Terzi, Eleni; Samara, Constantini

    Particle-bound aliphatic and polycyclic aromatic hydrocarbons (AHs and PAHs, respectively) were determined in the ambient air of the Eordea basin, in western Greece, where intensive coal burning for power generation takes place. Thirteen PAHs, n-alkanes (C 14-C 35), hopanes, and isoprenoid hydrocarbons (pristane and phytane) were determined in the total suspended particles collected from the atmosphere of four sites within the basin receiving potential impacts from various sources, such as fly ash, coal mining, automobile traffic, domestic heating, and agricultural or refuse burning. The same organic species were also determined in the fly ash generated in power stations, and in particulate emissions from open burning of biomass (dry corn leaves) and refuse burning. Organic particle sources were resolved using concentration diagnostic ratios and factor analysis (FA). A multivariate statistical receptor model (Absolute Principal Component Analysis, APCA) was finally employed to estimate the contribution of identified sources to the measured concentrations of organic pollutants. Four major sources for ambient PAHs and AHs were identified displaying variable contribution in different sites: (a) fossil fuel combustion, (b) biogenic emissions, (c) refuse burning, and (d) oil residues. Fuel combustion was the major source of ambient PAHs and an important source of n-alkanes in the range C 21-C 28. Oil residues were found to be the major source of low molecular weight n-alkanes (particularly the C 14-C 16), and an important source of pristane, phytane and UCM. Biogenic sources were primarily responsible for the high molecular weight n-alkanes explaining almost the entire concentration levels of homologues >C 32. Biomass burning was particularly important for the C 23-C 26n-alkanes. Despite the vicinity of certain sampling sites to power stations, coal fly ash was not identifiable as a source for ambient PAHs and AHs.

  17. Impact of carbon, oxygen and sulfur content of microscale zerovalent iron particles on its reactivity towards chlorinated aliphatic hydrocarbons.

    PubMed

    Velimirovic, Milica; Larsson, Per-Olof; Simons, Queenie; Bastiaens, Leen

    2013-11-01

    Zerovalent iron (ZVI) abiotically degrades several chlorinated aliphatic hydrocarbons (CAHs) via reductive dechlorination, which offers perspectives for in situ groundwater remediation applications. The difference in reactivity between ZVI particles is often linked with their specific surface area. However, other parameters may influence the reactivity as well. Earlier, we reported for a set of microscale zerovalent iron (mZVI) particles the disappearance kinetic of different CAHs which were collected under consistent experimental conditions. In the present study, these kinetic data were correlated with the carbon, oxygen and sulfur content of mZVI particles. It was confirmed that not only the specific surface area affects the disappearance kinetic of CAHs, but also the chemical composition of the mZVI particles. The chemical composition, in addition, influences CAHs removal mechanism inducing sorption onto mZVI particles instead of dechlorination. Generally, high disappearance kinetic of CAHs was observed for particles containing less oxygen. A high carbon content, on the other hand, induced nonreactive sorption of the contaminants on the mZVI particles. To obtain efficient remediation of CAHs by mZVI particles, this study suggested that the carbon and oxygen content should not exceed 0.5% and 1% respectively. Finally, the efficiency of the mZVI particles may be improved to some extent by enriching them with sulfur. However, the impact of sulfur content on the reactivity of mZVI particles is less pronounced than that of the carbon and oxygen content. PMID:23962383

  18. Identifying sources of chlorinated aliphatic hydrocarbons in a residential area in Italy using the integral pumping test method

    NASA Astrophysics Data System (ADS)

    Alberti, Luca; Lombi, Silvia; Zanini, Andrea

    2011-09-01

    The results of integral pumping tests (IPTs) performed in the city of Fabriano, Italy, are presented. The IPT methodology was developed by the European Union project INCORE, as a tool for groundwater investigation and source localization in contaminated areas. This methodology consists of a multiple-well pumping test in which the wells are positioned along a control plane downstream of suspected contaminant source zones and perpendicular to the mean groundwater flow direction. During the pumping, concentration time series of target contaminants are measured. In Fabriano, two control planes were realized to identify a chlorinated aliphatic hydrocarbon plume, to estimate the mass fluxes and draw up a ranked list of the main contamination sources. A numerical flow model was implemented to support the IPT design and to interpret the results. This study revealed low-level trichloroethylene contamination (concentration below 8 μg/l), tetrachloroethylene contamination (mean concentration up to 500 μg/l) and a mass flow rate of about 300 g/day. Through the application of the IPT method, the mean contaminant concentrations, the spatial distribution of concentration values along the control planes, and the total contaminant mass flow rates were evaluated, and the investigation area was reduced for further and deeper investigation activities.

  19. GREEN CATALYZED OXIDATION OF HYDROCARBONS IN ALTERNATIVE SOLVENT SYSTEMS GENERATED BY PARIS II

    EPA Science Inventory

    Green Catalyzed Oxidation of Hydrocarbons in Alternative Solvent Systems Generated by PARIS II

    Michael A. Gonzalez*, Thomas M. Becker, and Paul F. Harten; Sustainable Technology Division, Office of Research and Development; United States Environmental Protection Agency, 26...

  20. PHASE BEHAVIOR OF LIGHT GASES IN HYDROCARBON AND AQUEOUS SOLVENTS

    SciTech Connect

    KHALED A.M. GASEM; ROBERT L. ROBINSON, JR.

    1998-08-31

    Under previous support from the Department of Energy, an experimental facility has been established and operated to measure valuable vapor-liquid equilibrium data for systems of interest in the production and processing of coal fluids. To facilitate the development and testing of models for prediction of the phase behavior for such systems, we have acquired substantial amounts of data on the equilibrium phase compositions for binary mixtures of heavy hydrocarbon solvents with a variety of supercritical solutes, including hydrogen, methane, ethane, carbon monoxide, and carbon dioxide. The present project focuses on measuring the phase behavior of light gases and water in Fischer-Tropsch (F-T) type solvents at conditions encountered in indirect liquefaction processes and evaluating and developing theoretically-based correlating frameworks to predict the phase behavior of such systems. Specific goals of the proposed work include (a) developing a state-of-the-art experimental facility to permit highly accurate measurements of equilibrium phase compositions (solubilities) of challenging F-T systems, (b) measuring these properties for systematically-selected binary, ternary and molten F-T wax mixtures to provide critically needed input data for correlation development, (c) developing and testing models suitable for describing the phase behavior of such mixtures, and (d) presenting the modeling results in generalized, practical formats suitable for use in process engineering calculations. During the present period, the Park-Gasem-Robinson (PGR) equation of state (EOS) has been modified to improve its volumetric and equilibrium predictions. Specifically, the attractive term of the PGR equation was modified to enhance the flexibility of the model, and a new expression was developed for the temperature dependence of the attractive term in this segment-segment interaction model. The predictive capability of the modified PGR EOS for vapor pressure, and saturated liquid and

  1. Improvement of hydrocarbon recovery by spouting solvent into culture of Botryococcus braunii.

    PubMed

    Choi, Seung Phill; Bahn, Sang-Hoon; Sim, Sang Jun

    2013-12-01

    Botryococcus braunii, a green microalga, is known to produce plentiful liquid hydrocarbons as promising biodiesel resources. However, the hydrocarbon extraction methods that have so far achieved have several problems such as low efficiency and high cost. In our study, a solvent-spouted extraction process integrated with photo-bioculture was designed for simultaneous realization of hydrocarbon extraction and cell culture in two phases. The n-octane was selected as the best solvent among several solvents because its biocompatibility was highest for B. braunii. As a result, high level of biomass and hydrocarbon, 4.17 and 893.79 mg/L, respectively, was attained at 100 mL/min of solvent recycling rate through three times of processes for 66 days. Moreover, formation of cell clump was suppressed in solvent extraction, cells were regenerated after it, and thus cell viability was maintained even after repeated cycles of it. Finally, this solvent-spouted culture process required the smaller cost due to reuse of the less solvent and regenerated cells, compared with the other conventional methods. Accordingly, this technique would be applicable to exploit the continuous extraction of hydrocarbon from the algal biomass, especially for application on a large scale. PMID:23703677

  2. Kinetic modelling of the oxidation of large aliphatic hydrocarbons using an automatic mechanism generation.

    PubMed

    Muharam, Yuswan; Warnatz, Jürgen

    2007-08-21

    A mechanism generator code to automatically generate mechanisms for the oxidation of large hydrocarbons has been successfully modified and considerably expanded in this work. The modification was through (1) improvement of the existing rules such as cyclic-ether reactions and aldehyde reactions, (2) inclusion of some additional rules to the code, such as ketone reactions, hydroperoxy cyclic-ether formations and additional reactions of alkenes, (3) inclusion of small oxygenates, produced by the code but not included in the handwritten C(1)-C(4) sub-mechanism yet, to the handwritten C(1)-C(4) sub-mechanism. In order to evaluate mechanisms generated by the code, simulations of observed results in different experimental environments have been carried out. Experimentally derived and numerically predicted ignition delays of n-heptane-air and n-decane-air mixtures in high-pressure shock tubes in a wide range of temperatures, pressures and equivalence ratios agree very well. Concentration profiles of the main products and intermediates of n-heptane and n-decane oxidation in jet-stirred reactors at a wide range of temperatures and equivalence ratios are generally well reproduced. In addition, the ignition delay times of different normal alkanes was numerically studied. PMID:17687471

  3. Phase Behavior of Light Gases in Hydrocarbon and Aqueous Solvents

    SciTech Connect

    Gasem, K.A.M.; Robinson, R.L., Jr.; Trvedi, N.J., Gao, W.

    1997-09-01

    Under previous support from the Department of Energy, an experimental facility has been established and operated to measure valuable vapor-liquid equilibrium data for systems of interest in the production and processing of coal fluids. To facilitate the development and testing of models for prediction of the phase behavior for such systems, we have acquired substantial amounts of data on the equilibrium phase compositions for binary mixtures of heavy hydrocarbon solvents with a variety of supercritical solutes, including hydrogen, methane, ethane, carbon monoxide, and carbon dioxide. The present project focuses on measuring the phase behavior of light gases and water in Fischer-Tropsch (F-T) type solvents at conditions encountered in indirect liquefaction processes and evaluating and developing theoretically-based correlating frameworks to predict the phase behavior of such systems. Specific goals of the proposed work include (a) developing a state-of-the-art experimental facility to permit highly accurate measurements of equilibrium phase compositions (solubilities) of challenging F-T systems, (b) measuring these properties for systematically-selected binary, ternary and molten F-T wax mixtures to provide critically needed input data for correlation development, (c) developing and testing models suitable for describing the phase behavior of such mixtures, and (d) presenting the modeling results in generalized, practical formats suitable for use in process engineering calculations. During the present reporting period, our solubility apparatus was refurbished and restored to full service. To test the experimental apparatus and procedures used, measurements were obtained for the solubility Of C0{sub 2} in benzene at 160{degrees}F. Having confirmed the accuracy of the newly acquired data in comparison with our previous measurements and data reported in the literature for this test system, we have begun to measure the solubility of hydrogen in hexane. The measurements

  4. Predicting the stability of aprotic solvents in Li-air batteries: pKa calculations of aliphatic C-H acids in dimethyl sulfoxide

    NASA Astrophysics Data System (ADS)

    Bryantsev, Vyacheslav S.

    2013-02-01

    Superoxide is a strong base that can induce base-catalyzed autoxidation of weakly acidic solvents. We report on the performance of several computational protocols for predicting pKa values for a wide range of aliphatic C-H acids in DMSO. Calculations at the MP2/CBS level with CCSD(T)/aug-cc-pVDZ corrections and solvent effects calculated using the SVPE model provide the best overall performance (rms deviation is 0.65 pKa). The B3LYP, M06, and M06-2X functionals can also achieve high accuracy (<1 pKa) by employing empirical corrections to fit the experimental data. Computational results provide a convenient means of screening for suitable solvents in Li-air batteries.

  5. Process for extractive-stripping of lean hydrocarbon gas streams at high pressure with a preferential physical solvent

    SciTech Connect

    Bunting, T.N.

    1987-09-22

    This patent describes a process for selectively extracting hydrocarbons from a hydrocarbon gas feed stream with a preferential physical solvent which provides selective capability for extremely high recoveries according to any selected degree of a selected hydrocarbon component and heavier hydrocarbons within the group consisting of ethane, propane, butane, and pentane without the need simultaneously to recover hydrocarbons lighter than the selected hydrocarbon component from the hydrocarbon gas feed stream. The recoveries are: (a) ethane in amounts within the range of 2-100%, (b) propane in amounts within the range of 2-100%, (c) butane in amounts within the range of 2-100%, or (d) pentanes and higher molecular weight hydrocarbons in amounts ranging up to 100% by the following steps: (a) selectively extracting and stripping the hydrocarbon gas feed stream with the physical solvent to produce a residue hydrocarbon gas stream of pipeline specifications and a rich solvent stream containing ethane and heavier hydrocarbon components, (b) distilling the rich solvent to produce: (1) the selected hydrocarbon component and heavier hydrocarbons as overhead product. The improvement comprises the selective enrichment of the hydrocarbon gas feed stream with recycle of a selected portion of the overhead product to the extracting and stripping step, whereby the extremely high recoveries according to the any selected degree are feasible without the excessive solvent flow rates or the high reboiler temperatures.

  6. [Extraction characteristics of sequential accelerated solvent extraction for polycyclic aromatic hydrocarbons in environmental mediums].

    PubMed

    Ma, Xiao-xuan; Ran, Yong

    2009-12-01

    Polycyclic aromatic hydrocarbons (PAHs) in two soils, two sediments and an shale from the Pearl River Delta were extracted by sequential accelerated solvent extraction (ASE) with each of four different organic solvents for three times. PAHs in the first extract accounts for more than half of their total contents, and toluene displays the best extraction performance among the four employed solvents. For a given sample the source diagnostic ratios of PAHs in sequential ASE with each solvent are very similar, suggesting the validity of those ratios in source judgement by different extraction methods. PMID:20187409

  7. The C–H Stretching Features at 3.2--3.5 μm of Polycyclic Aromatic Hydrocarbons with Aliphatic Sidegroups

    NASA Astrophysics Data System (ADS)

    Yang, X. J.; Li, Aigen; Glaser, R.; Zhong, J. X.

    2016-07-01

    The so-called “unidentified” infrared emission (UIE) features at 3.3, 6.2, 7.7, 8.6, and 11.3 μm are ubiquitously seen in a wide variety of astrophysical regions. The UIE features are characteristic of the stretching and bending vibrations of aromatic hydrocarbon materials, e.g., polycyclic aromatic hydrocarbon (PAH) molecules. The 3.3 μm aromatic C–H stretching feature is often accompanied by a weaker feature at 3.4 μm. The latter is generally thought to result from the C–H stretch of aliphatic groups attached to the aromatic systems. The ratio of the observed intensity of the 3.3 μm aromatic C–H feature to that of the 3.4 μm aliphatic C–H feature allows one to estimate the aliphatic fraction of the UIE carriers, provided that the intrinsic oscillator strengths of the 3.3 μm aromatic C–H stretch ({A}3.3) and the 3.4 μm aliphatic C–H stretch ({A}3.4) are known. While previous studies on the aliphatic fraction of the UIE carriers were mostly based on the {A}3.4/{A}3.3 ratios derived from the mono-methyl derivatives of small PAH molecules, in this work we employ density functional theory to compute the infrared vibrational spectra of PAH molecules with a wide range of sidegroups including ethyl, propyl, butyl, and several unsaturated alkyl chains, as well as all the isomers of dimethyl-substituted pyrene. We find that, except for PAHs with unsaturated alkyl chains, the corresponding {A}3.4/{A}3.3 ratios are close to that of mono-methyl PAHs. This confirms the predominantly aromatic nature of the UIE carriers previously inferred from the {A}3.4/{A}3.3 ratio derived from mono-methyl PAHs.

  8. Particulate Fluxes of Aliphatic and Aromatic Hydrocarbons in Near-shore Waters to the Northwestern Mediterranean Sea, and the Effect of Continental Runoff

    NASA Astrophysics Data System (ADS)

    Raoux, C.; Boyona, J. M.; Miquel, J.-C.; Teyssie, J.-L.; Fowler, S. W.; Albaigés, J.

    1999-05-01

    Particulate fluxes of aliphatic and aromatic hydrocarbons were measured with a sediment trap moored at 80m depth offshore Monaco (200m water column) during an 18-month period. The highest fluxes of n -alkanes and polycyclic aromatic hydrocarbons (PAH) ( c . 300 and 10μg m -2day -1, respectively) were noted following a strong rainfall event (March-April 1989) and were mostly accounted for by continental runoff and river outflows. Fluxes during periods of low precipitation (August 1989-August 1990) were one order of magnitude lower for PAHs (1·51±1·40μg m -2day -1) or two orders of magnitude lower for n -alkanes (4·79±3·3μg m -2day -1) than during the earlier period (March-April 1989). The total PAH and total particle fluxes exhibited a positive linear correlation during the entire sampling period ( r =0·87, N =31, P< 0·05) underscoring the strong affinity of PAHs for particles. Examination of the seasonal variability of fecal pellet content, associated parameters (total organic carbon, total carbon, nitrogen), and individual hydrocarbon content of particles by Principal Component Analysis (PCA) showed that aliphatic and aromatic hydrocarbons were clustered in several subgroups in the PCA loading plots according to their origin. n -Alkanes were grouped in two clusters: (i) lower molecular weight ( n -C 16-19) and (ii) the higher molecular weight alkanes ( n -C 20-38) suggesting different pathways into the coastal zone (i.e. runoff vs atmospheric deposition). The distribution of lycopane, pristane and phytane indicated multiple origins. However, the closer location of the two isoprenoids, lycopane and pristane to fecal pellets, suggests a zooplanktonic origin but phytane to fossil fuel source. PAHs exhibited a variety of pyrolytic sources and only fluoranthene and pyrene were not grouped with the remaining PAHs suggesting multiple sources of pollution in these waters.

  9. 40 CFR Table 4 to Subpart Mmmm of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... Hydrocarbon, Aliphatic Hydrocarbon, Aliphatic Naphtha, Naphthol Spirits, Petroleum Spirits, Petroleum Oil... Naphtha, Light Aromatic Naphtha, Light Aromatic Hydrocarbons, Aromatic Hydrocarbons, Light...

  10. Coal liquefaction process using pretreatment with a binary solvent mixture

    DOEpatents

    Miller, Robert N.

    1986-01-01

    An improved process for thermal solvent refining or hydroliquefaction of non-anthracitic coal at elevated temperatures under hydrogen pressure in a hydrogen donor solvent comprises pretreating the coal with a binary mixture of an aromatic hydrocarbon and an aliphatic alcohol at a temperature below 300.degree. C. before the hydroliquefaction step. This treatment generally increases both conversion of coal and yields of oil.

  11. GREEN CATALYZED OXIDATION OF HYDROCARBONS IN ALTERNATIVE SOLVENT SYSTEMS GENERATED BY PARIS II DECHEMA; GREEN SOLVENTS FOR CATALYSIS - ENVIRONMENTALLY BENIGN REACTION MEDIA

    EPA Science Inventory

    Green catalyzed oxidation of hydrocarbons in alternative solvent systems generated by PARIS II
    Thomas M. Becker, Michael A. Gonzalez, Paul F. Harten; Sustainable Technology Division, Office of Research and Development; United States Environmental Protection Agency, 26 West Mar...

  12. Heavy recycle solvent studies in two-stage coal liquefaction. Final technical report, September 1, 1982-December 30, 1983

    SciTech Connect

    Longanbach, J. R.

    1984-01-10

    The objective of this program has been to study the chemistry of the components with high boiling points in a direct coal liquefaction recycle solvent and to identify those components which lead to higher overall yields and improved product stability in the initial coal dissolution step of direct coal liquefaction processes. The major conclusions are: -454 C recycle solvent is primarily aromatic hydrocarbons (73%) and contains almost no asphaltenes; +454 C recycle solvent is primarily asphaltenes and aromatic hydrocarbons; recycle solvent also contains aliphatic hydrocarbons, N-containing aromatics and O-containing aromatics; heteroatoms in coal derived materials seem to be grouped by type, i.e. acidic O and basic N and sulfur occur together; under helium a small net amount of hydrogen and more CO and CO/sub 2/ are produced than under hydrogen; under hydrogen the amounts of H/sub 2/S and hydrocarbon gases are increased and a small amount of hydrogen gas is usually consumed; overall coal conversions to THF solubles are improved by adding more -454 C solvent but decreased by adding +454 C solvent; for added fractions of -454 C solvent the pecent conversion to THF solubles increases in the order aromatic hydrocarbons (+7.2) > aliphatic hydrocarbons (+0.8) > no added solvent (0.0) > N-containing aromatics (-0.9) > O-containing aromatics (-22.1); percent conversion to THF solubles using -454 C solvent with +454 C solvent fractions added decrease in the order aliphatics (+3.7) > aromatic hydrocarbons (+3.0) > no added solvent (0.0) > O-containing aromatics (-9.3) > N-containing aromatics (-13.3); of the +454 C solvent components, aromatic hydrocarbons and aliphatic hydrocarbons are beneficial but total only approx. 25% of the +454 C recycle solvent; and steric effects may be important in determining the effectiveness of the heavier solvent components as liquefaction solvents. 28 references, 25 figures, 31 tables.

  13. Occurrence of aliphatic and polyaromatic hydrocarbons (PAHs) in Mytillus galloprovincialis from the traditional market in Marseille, France, by Gas Chromatography triplequadropole tandem Mass Spectrometry (GC-QQQ/MS)

    NASA Astrophysics Data System (ADS)

    Azis, M. Y.; Yelmiza; Asia, L.; Piram, A.; Bucharil, B.; Doumenq, P.; Syakti, A. D.

    2016-02-01

    Mediterranean mussel, Mytillusgalloprovincialis collected from the traditional market in Marseille, France,have been analysed using GC-QQQ/MS for their hydrocarbons (n-alkanes and polyaromatic hydrocarbons (PAHs)) extentwith two different solvent extraction, such as heptane:dichloromethane (HEP:DCM;1:1) and heptane:acetone (HEP:ACE; 1:1). The results showed hydrocarbons yielded from heptane:acetone extractionwere 28335 μg.kg- 1mussels dw (Ʃ n-alkanes C15-34) and 202 μg.kg-1mussels dw(ƩPAHs) while the yield from heptane:DCM extract was lower ca. 27026 μg.kg-1musselsdw and 133 μg.kg-1 mussels dw respectively from the Ʃn-alkanesC15-34and ƩPAHs. High hydrocarbon levels can be affected by the presence of lipids or other metabolites in mussels that have the same polarity with hydrocarbon compounds which has interferred the measurement. Several ratio parameter of n- alcanes and PAHs source in the mussels were evaluated to asses the origins of their hydrocarbons in mussels from which we suggested origins of hydrocarbons were pyrolytic and biogenic rather than petrogenic.

  14. Identification and biotransformation of aliphatic hydrocarbons during co-composting of sewage sludge-Date Palm waste using Pyrolysis-GC/MS technique.

    PubMed

    El Fels, Loubna; Lemee, Laurent; Ambles, André; Hafidi, Mohamed

    2016-08-01

    The behavior of aliphatic hydrocarbons during co-composting of sewage sludge activated with palm tree waste was studied for 6 months using Py-GC/MS. The main aliphatic compounds represented as doublet alkenes/alkanes can be classified into three groups. The first group consists of 11 alkenes (undecene, tridecene, pentadecene, hexadecene, heptadecene, octadecene, nonadecene, eicosene, uncosene, docosene, tricosene) and 15 alkanes (heptane, octane, nonane, decane, undecane, dodecane, tetradecane, pentadecane, heptadecane, octadecane, nonadecane, eicosane, uncosane, docosane, and tricosane), which remain stable during the co-composting process. The stability of these compounds is related to their recalcitrance behavior. The second group consists of five alkenes (heptene, octene, nonene, decene, dodecene) and tridecane as a single alkane that decreases during co-composting. The decrease in these compounds is the combined result of their metabolism and their conversion into other compounds. The third group is constituted with tetradecene and hexadecane that increase during composting, which could be explained by accumulation of these compounds, which are released by the partial breakdown of the substrate. As a result, these molecules are incorporated or adsorbed in the structure of humic substances. PMID:27197656

  15. Microwave-assisted solvent extraction of polynuclear aromatic hydrocarbons from soils -- report of an interlaboratory study

    SciTech Connect

    Jassie, L.B.; Kierstead, T.; Hays, M.J.; Wise, S.A.

    1995-12-31

    Solvent extractions are among the oldest and most widely practiced sample preparation techniques for chemical analysis. Solvents are selected to dissolve target analytes based on the affinity between solvent and solute and range from highly polar molecules like water to lipophilic hydrocarbons, depending on the target analyte. Although traditional liquid/solid extraction methods are labor intensive and often time consuming, newer extraction techniques using microwave heating more efficiently leach additives from plastics, natural products from botanicals, and pesticides and PAHs from sediment. Certain solvent molecules heat well in microwave fields because the electromagnetic radiation couples with the polar species and energy is transferred to the solution through dipole rotation. We`ll show why some solvents are more logical choices for matching microwave heating technology with an extraction application. Results will be presented of a study extracting PAHs from materials of environmental interest along with the results of a round robin we conducted comparing the recovery efficiency of microwave extractions with conventional extractions. We have also been evaluating solvents with good dielectric properties which may lead to more efficient and environmentally friendly extraction systems. Closed vessel microwave extraction dramatically reduces the solvent volumes needed and the length of the extraction step. With automated cleanup, improved sample throughput is possible.

  16. Polycyclic aromatic and aliphatic hydrocarbons in Chukchi Sea biota and sediments and their toxicological response in the Arctic cod, Boreogadus saida

    NASA Astrophysics Data System (ADS)

    Harvey, H. Rodger; Taylor, Karen A.; Pie, Hannah V.; Mitchelmore, Carys L.

    2014-04-01

    As part of the Chukchi Sea Offshore Monitoring in Drilling Area-Chemical and Benthos (COMIDA CAB) project, we determined the distribution and concentrations of aliphatic n-alkanes and polycyclic aromatic hydrocarbons (PAHs) in surface sediments (0-1 cm) among 52 sites across the Chukchi Sea and in muscle tissues of the benthic Northern whelk, Neptunea heros, collected opportunistically. In addition, downcore profiles of contaminants were determined at three targeted sites to establish historic patterns. Baseline responses of PAH exposure and its potential toxicological effects were examined in the common Arctic cod, Boreogadus saida, through measures of cytochrome P4501A/ ethoxyresorufin O-deethylase (CYP1A/EROD), glutathione-S-transferase (GST), and Cu/Zn superoxide dismutase (SOD) activity in liver tissue. The total concentration of PAHs in surface sediments throughout the study area, including parent and alkyl-homologs, were very low (<1600 ng g-1 dry wt) except for a single station, where values were 2-20-fold greater than at other baseline sites (2956 ng g-1 dry wt). Alkyl-substituted PAHs were the dominant form in all surface (54-93%) and subsurface sediments (50-81% of the total), with a general decrease in total PAH concentrations observed downcore. In biota, larger Neptunea showed lower total concentrations of PAHs in foot muscles (4.5-10.7 ng g-1 wet wt) compared to smaller animals; yet aliphatic n-alkane (C19-C33) concentrations (0.655-5.20 μg g-1 wet wt) increased in larger organisms with distributions dominated by long-chain (C23-C33) hydrocarbons. In B. saida, CYP1A1, GST, and SOD enzyme levels were comparable to baseline levels previously reported in other pristine systems. Of the three assays, only SOD had a significant correlation between gene expression and enzyme activity.

  17. Approach to estimation of absorption of aliphatic hydrocarbons diffusing from interior materials in an automobile cabin by inhalation toxicokinetic analysis in rats.

    PubMed

    Yoshida, Toshiaki

    2010-01-01

    The interior air of an automobile cabin has been demonstrated in our previous studies to be contaminated by high concentrations of a large variety of aliphatic hydrocarbons diffusing from the interior materials. In the present study, the amounts of seven selected aliphatic hydrocarbons absorbed by the car driver were estimated by evaluating their inhalation toxicokinetics in rats. Measured amounts of the substances were injected into a closed chamber system in which a rat had been placed, and the concentration changes in the chamber were examined. The toxicokinetics of the substances were evaluated based on concentration-time courses using a nonlinear compartment model. Their absorption amounts in humans at the levels of actual concentrations in the cabins without ventilation were extrapolated from the results found with the rats. The absorption amounts estimated for a driver during a 2 h drive were as follows: 6 microg/60 kg of human body weight for methylcyclopentane (interior concentration 23 microg/m(3) as median value in previous study), 5 microg for 2-methylpentane (36 microg/m(3)), 13 microg for n-hexane (65 microg/m(3)), 51 microg for n-heptane (150 microg/m(3)), 26 microg for 2,4-dimethylheptane (97 microg/m(3)), 17 microg for n-nonane (25 microg/m(3)) and 49 microg for n-decane (68 microg/m(3)). An inverse relationship was found between the exposure and absorption among the substances (e.g. between n-decane and 2,4-dimethylheptane). These findings suggest that not only the exposure concentrations but also the absorption amounts should be taken into account to evaluate the health effects of exposure to low concentrations of volatile compounds as environmental contaminants. PMID:19743389

  18. Microbial production of aliphatic (S)-epoxyalkanes by using Rhodococcus sp. strain ST-10 styrene monooxygenase expressed in organic-solvent-tolerant Kocuria rhizophila DC2201.

    PubMed

    Toda, Hiroshi; Ohuchi, Takuya; Imae, Ryouta; Itoh, Nobuya

    2015-03-01

    We describe the development of biocatalysis for producing optically pure straight-chain (S)-epoxyalkanes using styrene monooxygenase of Rhodococcus sp. strain ST-10 (RhSMO). RhSMO was expressed in the organic solvent-tolerant microorganism Kocuria rhizophila DC2201, and the bioconversion reaction was performed in an organic solvent-water biphasic reaction system. The biocatalytic process enantioselectively converted linear terminal alkenes to their corresponding (S)-epoxyalkanes using glucose and molecular oxygen. When 1-heptene and 6-chloro-1-hexene were used as substrates (400 mM) under optimized conditions, 88.3 mM (S)-1,2-epoxyheptane and 246.5 mM (S)-1,2-epoxy-6-chlorohexane, respectively, accumulated in the organic phase with good enantiomeric excess (ee; 84.2 and 95.5%). The biocatalysis showed broad substrate specificity toward various aliphatic alkenes, including functionalized and unfunctionalized alkenes, with good to excellent ee. Here, we demonstrate that this biocatalytic system is environmentally friendly and useful for producing various enantiopure (S)-epoxyalkanes. PMID:25556188

  19. An Aliphatic Solvent-Soluble Lithium Salt of the Perhalogenated Weakly Coordinating Anion [Al(OC(CCl3)(CF3)2)4](-).

    PubMed

    Zheng, Xin; Zhang, Zaichao; Tan, Gengwen; Wang, Xinping

    2016-02-01

    The facile synthesis of a new highly aliphatic solvent-soluble Li(+) salt of the perhalogenated weakly coordinating anion [Al(OC(CCl3)(CF3)2)4](-) and its application in stabilizing the Ph3C(+) cation were investigated. The lithium salt Li[Al(OC(CCl3)(CF3)2)4] (4) was prepared by the treatment of 4 mol equiv of HOC(CCl3)(CF3)2 with purified LiAlH4 in n-hexane from -20 °C to room temperature. Compound 4 is highly soluble in both polar and nonpolar solvents, and it bears both CCl3 and CF3 groups, resulting in a lower symmetry around the Al center compared to that of Li[Al(OC(CF3)3)4] (1). Treatment of 4 with Ph3CCl afforded the ionic compound [Ph3C][Al(OC(CCl3)(CF3)2)4] (5) bearing the Ph3C(+) cation with concomitant elimination of LiCl, suggesting the potential application of [Al(OC(CCl3)(CF3)2)4](-) in stabilizing reactive cationic species. Compounds 4 and 5 were fully characterized by spectroscopic and structural methods. PMID:26784742

  20. Microbial Production of Aliphatic (S)-Epoxyalkanes by Using Rhodococcus sp. Strain ST-10 Styrene Monooxygenase Expressed in Organic-Solvent-Tolerant Kocuria rhizophila DC2201

    PubMed Central

    Toda, Hiroshi; Ohuchi, Takuya; Imae, Ryouta

    2015-01-01

    We describe the development of biocatalysis for producing optically pure straight-chain (S)-epoxyalkanes using styrene monooxygenase of Rhodococcus sp. strain ST-10 (RhSMO). RhSMO was expressed in the organic solvent-tolerant microorganism Kocuria rhizophila DC2201, and the bioconversion reaction was performed in an organic solvent-water biphasic reaction system. The biocatalytic process enantioselectively converted linear terminal alkenes to their corresponding (S)-epoxyalkanes using glucose and molecular oxygen. When 1-heptene and 6-chloro-1-hexene were used as substrates (400 mM) under optimized conditions, 88.3 mM (S)-1,2-epoxyheptane and 246.5 mM (S)-1,2-epoxy-6-chlorohexane, respectively, accumulated in the organic phase with good enantiomeric excess (ee; 84.2 and 95.5%). The biocatalysis showed broad substrate specificity toward various aliphatic alkenes, including functionalized and unfunctionalized alkenes, with good to excellent ee. Here, we demonstrate that this biocatalytic system is environmentally friendly and useful for producing various enantiopure (S)-epoxyalkanes. PMID:25556188

  1. Relationship between lipophilicity of C6-10 hydrocarbon solvents and their ROS-inducing potency in rat cerebellar granule cells.

    PubMed

    Dreiem, A; Myhre, O; Fonnum, F

    2002-12-01

    We have studied the effects of aliphatic, alicyclic, and aromatic C6-10 solvents on the formation of reactive oxygen species (ROS) in rat cerebellar granule cell cultures. ROS formation was assessed by monitoring oxidation of 2',7'-dichlorofluorescin (DCFH) to the fluorescent compound 2',7'-dichlorofluorescein (DCF). We found that aromatic solvents with C > 7, and aliphatic and alicyclic solvents with C > or = 7 induce ROS formation in rat cerebellar granule cells in vitro. The response increased with increasing solvent concentration. The potency of the compounds within each homologous group seemed to be correlated to their octanol water partition-coefficients. The aromatic solvents were generally less efficient in inducing ROS formation than the aliphatic and the alicyclic compounds. PMID:12520760

  2. Degradation of recalcitrant aliphatic and aromatic hydrocarbons by a dioxin-degrader Rhodococcus sp. strain p52.

    PubMed

    Yang, Hai-Yan; Jia, Rui-Bao; Chen, Bin; Li, Li

    2014-09-01

    This study investigates the ability of Rhodococcus sp. strain p52, a dioxin degrader, to biodegrade petroleum hydrocarbons. Strain p52 can use linear alkanes (tetradecane, tetracosane, and dotriacontane), branched alkane (pristane), and aromatic hydrocarbons (naphthalene and phenanthrene) as sole carbon and energy sources. Specifically, the strain removes 85.7 % of tetradecane within 48 h at a degradation rate of 3.8 mg h(-1) g(-1) dry cells, and 79.4 % of tetracosane, 66.4 % of dotriacontane, and 63.9 % of pristane within 9-11 days at degradation rates of 20.5, 14.7, and 20.3 mg day(-1) g(-1) dry cells, respectively. Moreover, strain p52 consumes 100 % naphthalene and 55.3 % phenanthrene within 9-11 days at respective degradation rates of 16 and 12.9 mg day(-1) g(-1) dry cells. Metabolites of the petroleum hydrocarbons by strain p52 were analyzed. Genes encoding alkane-hydroxylating enzymes, including cytochrome P450 (CYP450) enzyme (CYP185) and two alkane-1-monooxygenases, were amplified by polymerase chain reaction. The transcriptional activities of these genes in the presence of petroleum hydrocarbons were detected by reverse transcription-polymerase chain reaction. The results revealed potential of strain p52 to degrade petroleum hydrocarbons. PMID:24859700

  3. Occupational exposures to new dry cleaning solvents: High-flashpoint hydrocarbons and butylal.

    PubMed

    Ceballos, Diana M; Whittaker, Stephen G; Lee, Eun Gyung; Roberts, Jennifer; Streicher, Robert; Nourian, Fariba; Gong, Wei; Broadwater, Kendra

    2016-10-01

    The dry cleaning industry is moving away from using perchloroethylene. Occupational exposures to two alternative dry cleaning solvents, butylal and high-flashpoint hydrocarbons, have not been well characterized. We evaluated four dry cleaning shops that used these alternative solvents. The shops were staffed by Korean- and Cantonese-speaking owners, and Korean-, Cantonese-, and Spanish-speaking employees. Because most workers had limited English proficiency we used language services in our evaluations. In two shops we collected personal and area air samples for butylal. We also collected air samples for formaldehyde and butanol, potential hydrolysis products of butylal. Because there are no occupational exposure limits for butylal, we assessed employee health risks using control banding tools. In the remaining two shops we collected personal and area air samples for high-flashpoint hydrocarbon solvents. In all shops the highest personal airborne exposures occurred when workers loaded and unloaded the dry cleaning machines and pressed dry cleaned fabrics. The air concentrations of formaldehyde and butanol in the butylal shops were well below occupational exposure limits. Likewise, the air concentrations of high-flashpoint hydrocarbons were also well below occupational exposure limits. However, we saw potential skin exposures to these chemicals. We provided recommendations on appropriate work practices and the selection and use of personal protective equipment. These recommendations were consistent with those derived using control banding tools for butylal. However, there is insufficient toxicological and health information to determine the safety of butylal in occupational settings. Independent evaluation of the toxicological properties of these alternative dry cleaning solvents, especially butylal, is urgently needed. PMID:27105306

  4. 40 CFR Table 7 to Subpart Kkkk of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., Naphtha, Mixed Hydrocarbon, Aliphatic Hydrocarbon, Aliphatic Naphtha, Naphthol Spirits, Petroleum Spirits... Naphtha, Aromatic Naphtha, Light Aromatic Naphtha, Light Aromatic Hydrocarbons, Aromatic...

  5. 40 CFR Table 7 to Subpart Kkkk of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ..., Naphtha, Mixed Hydrocarbon, Aliphatic Hydrocarbon, Aliphatic Naphtha, Naphthol Spirits, Petroleum Spirits... Naphtha, Aromatic Naphtha, Light Aromatic Naphtha, Light Aromatic Hydrocarbons, Aromatic...

  6. Natural attenuation of chlorinated solvents, petroleum hydrocarbons, and other organic compounds

    SciTech Connect

    Alleman, B.C.; Leeson, A.

    1999-11-01

    The natural attenuation option is getting more attention from site managers and regulators as a viable alternative to more costly engineered site remediation approaches. Natural attenuation was first demonstrated at sites with hydrocarbon contamination, but recent studies at sites contaminated by chlorinated compounds have shown that this approach often has merit for these more challenging contamination problems. Covering natural attenuation in media ranging from deep aquifers to shallow soils, and for contaminants ranging from fuels to solvents to herbicides, this volume offers the reader a comprehensive overview of case studies that represent the current state of the art in natural attenuation approaches to site remediation.

  7. In situ thermally enhanced biodegradation of petroleum fuel hydrocarbons and halogenated organic solvents

    DOEpatents

    Taylor, Robert T.; Jackson, Kenneth J.; Duba, Alfred G.; Chen, Ching-I

    1998-01-01

    An in situ thermally enhanced microbial remediation strategy and a method for the biodegradation of toxic petroleum fuel hydrocarbon and halogenated organic solvent contaminants. The method utilizes nonpathogenic, thermophilic bacteria for the thermal biodegradation of toxic and carcinogenic contaminants, such as benzene, toluene, ethylbenzene and xylenes, from fuel leaks and the chlorinated ethenes, such as trichloroethylene, chlorinated ethanes, such as 1,1,1-trichloroethane, and chlorinated methanes, such as chloroform, from past solvent cleaning practices. The method relies on and takes advantage of the pre-existing heated conditions and the array of delivery/recovery wells that are created and in place following primary subsurface contaminant volatilization efforts via thermal approaches, such as dynamic underground steam-electrical heating.

  8. In situ thermally enhanced biodegradation of petroleum fuel hydrocarbons and halogenated organic solvents

    DOEpatents

    Taylor, R.T.; Jackson, K.J.; Duba, A.G.; Chen, C.I.

    1998-05-19

    An in situ thermally enhanced microbial remediation strategy and a method for the biodegradation of toxic petroleum fuel hydrocarbon and halogenated organic solvent contaminants are described. The method utilizes nonpathogenic, thermophilic bacteria for the thermal biodegradation of toxic and carcinogenic contaminants, such as benzene, toluene, ethylbenzene and xylenes, from fuel leaks and the chlorinated ethenes, such as trichloroethylene, chlorinated ethanes, such as 1,1,1-trichloroethane, and chlorinated methanes, such as chloroform, from past solvent cleaning practices. The method relies on and takes advantage of the pre-existing heated conditions and the array of delivery/recovery wells that are created and in place following primary subsurface contaminant volatilization efforts via thermal approaches, such as dynamic underground steam-electrical heating. 21 figs.

  9. Solvent-impregnated agarose gel liquid phase microextraction of polycyclic aromatic hydrocarbons in water.

    PubMed

    Loh, Saw Hong; Sanagi, Mohd Marsin; Wan Ibrahim, Wan Aini; Hasan, Mohamed Noor

    2013-08-01

    A new microextraction procedure termed agarose gel liquid phase microextraction (AG-LPME) combined with gas chromatography-mass spectrometry (GC-MS) was developed for the determination of selected polycyclic aromatic hydrocarbons (PAHs) in water. The technique utilized an agarose gel disc impregnated with the acceptor phase (1-octanol). The extraction procedure was performed by allowing the solvent-impregnated agarose gel disc to tumble freely in the stirred sample solution. After extraction, the agarose gel disc was removed and subjected to centrifugation to disrupt its framework and to release the impregnated solvent, which was subsequently withdrawn and injected into the GC-MS for analysis. Under optimized extraction conditions, the new method offered high enrichment factors (89-177), trace level LODs (9-14ngL(-1)) and efficient extraction with good relative recoveries in the range of 93.3-108.2% for spiked drinking water samples. AG-LPME did not exhibit any problems related to solvent dissolution, and it provided high extraction efficiencies that were comparable to those of hollow fiber liquid phase microextraction (HF-LPME) and significantly higher than those of agarose film liquid phase microextraction (AF-LPME). This technique employed a microextraction format and utilized an environmentally compatible solvent holder that supported the green chemistry concept. PMID:23809804

  10. Zinc oxide/polypyrrole nanocomposite as a novel solid phase microextraction coating for extraction of aliphatic hydrocarbons from water and soil samples.

    PubMed

    Amanzadeh, Hatam; Yamini, Yadollah; Moradi, Morteza

    2015-07-16

    In this work, ZnO/PPy nanocomposite coating was fabricated on stainless steel and evaluated as a novel headspace solid phase microextraction (HS-SPME) fiber coating for extraction of ultra-trace amounts of environmental pollutants; namely, aliphatic hydrocarbons in water and soil samples. The ZnO/PPy nanocomposite were prepared by a two-step process including the electrochemical deposition of PPy on the surface of stainless steel in the first step, and the synthesis of ZnO nanorods by hydrothermal process in the pores of PPy matrix in the second step. Porous structure together with ZnO nanorods with the average diameter of 70 nm were observed on the surface by using scanning electron microscopy (SEM). The effective parameters on HS-SPME of hydrocarbons (i.e., extraction temperature, extraction time, desorption temperature, desorption time, salt concentration, and stirring rate) were investigated and optimized by one-variable-at-a-time method. Under optimized conditions (extraction temperature, 65±1°C; extraction time, 15 min; desorption temperature, 250°C; desorption time, 3 min; salt concentration, 10% w/v; and stirring rate, 1200 rpm), the limits of detection (LODs) were found in the range of 0.08-0.5 μg L(-1), whereas the repeatability and fiber-to-fiber reproducibility were in the range 5.4-7.6% and 8.6-10.4%, respectively. Also, the accuracies obtained for the spiked n-alkanes were in the range of 85-108%; indicating the absence of matrix effects in the proposed HS-SPME method. The results obtained in this work suggest that ZnO/PPy can be promising coating materials for future applications of SPME and related sample preparation techniques. PMID:26073809

  11. Oceanobacter-related bacteria are important for the degradation of petroleum aliphatic hydrocarbons in the tropical marine environment.

    PubMed

    Teramoto, Maki; Suzuki, Masahito; Okazaki, Fumiyoshi; Hatmanti, Ariani; Harayama, Shigeaki

    2009-10-01

    Petroleum-hydrocarbon-degrading bacteria were obtained after enrichment on crude oil (as a 'chocolate mousse') in a continuous supply of Indonesian seawater amended with nitrogen, phosphorus and iron nutrients. They were related to Alcanivorax and Marinobacter strains, which are ubiquitous petroleum-hydrocarbon-degrading bacteria in marine environments, and to Oceanobacter kriegii (96.4-96.5 % similarities in almost full-length 16S rRNA gene sequences). The Oceanobacter-related bacteria showed high n-alkane-degrading activity, comparable to that of Alcanivorax borkumensis strain SK2. On the other hand, Alcanivorax strains exhibited high activity for branched-alkane degradation and thus could be key bacteria for branched-alkane biodegradation in tropical seas. Oceanobacter-related bacteria became most dominant in microcosms that simulated a crude oil spill event with Indonesian seawater. The dominance was observed in microcosms that were unamended or amended with fertilizer, suggesting that the Oceanobacter-related strains could become dominant in the natural tropical marine environment after an accidental oil spill, and would continue to dominate in the environment after biostimulation. These results suggest that Oceanobacter-related bacteria could be major degraders of petroleum n-alkanes spilt in the tropical sea. PMID:19541999

  12. Magnetic ionic liquids as non-conventional extraction solvents for the determination of polycyclic aromatic hydrocarbons.

    PubMed

    Trujillo-Rodríguez, María J; Nacham, Omprakash; Clark, Kevin D; Pino, Verónica; Anderson, Jared L; Ayala, Juan H; Afonso, Ana M

    2016-08-31

    This work describes the applicability of magnetic ionic liquids (MILs) in the analytical determination of a group of heavy polycyclic aromatic hydrocarbons. Three different MILs, namely, benzyltrioctylammonium bromotrichloroferrate (III) (MIL A), methoxybenzyltrioctylammonium bromotrichloroferrate (III) (MIL B), and 1,12-di(3-benzylbenzimidazolium) dodecane bis[(trifluoromethyl)sulfonyl)]imide bromotrichloroferrate (III) (MIL C), were designed to exhibit hydrophobic properties, and their performance examined in a microextraction method for hydrophobic analytes. The magnet-assisted approach with these MILs was performed in combination with high performance liquid chromatography and fluorescence detection. The study of the extraction performance showed that MIL A was the most suitable solvent for the extraction of polycyclic aromatic hydrocarbons and under optimum conditions the fast extraction step required ∼20 μL of MIL A for 10 mL of aqueous sample, 24 mmol L(-1) NaOH, high ionic strength content of NaCl (25% (w/v)), 500 μL of acetone as dispersive solvent, and 5 min of vortex. The desorption step required the aid of an external magnetic field with a strong NdFeB magnet (the separation requires few seconds), two back-extraction steps for polycyclic aromatic hydrocarbons retained in the MIL droplet with n-hexane, evaporation and reconstitution with acetonitrile. The overall method presented limits of detection down to 5 ng L(-1), relative recoveries ranging from 91.5 to 119%, and inter-day reproducibility values (expressed as relative standard derivation) lower than 16.4% for a spiked level of 0.4 μg L(-1) (n = 9). The method was also applied for the analysis of real samples, including tap water, wastewater, and tea infusion. PMID:27506350

  13. Isolation and characterization of a Mycobacterium species capable of degrading three- and four-ring aromatic and aliphatic hydrocarbons

    SciTech Connect

    Churchill, S.A.; Harper, J.P.; Churchill, P.F.

    1999-02-01

    Mycobacterium sp. strain CH1 was isolated from polycyclic aromatic hydrocarbon (PAH)-contaminated freshwater sediments and identified by analysis of 16S rDNA sequences. Strain CH1 was capable of mineralizing three- and four-ring PAHs including phenanthrene, pyrene, and fluoranthene. In addition, strain CH1 could utilize phenanthrene or pyrene as a sole carbon and energy source. A lag phase of at least 3 days was observed during pyrene mineralization. This lag phase decreased to less than 1 day when strain CH1 was grown in the presence of phenanthrene or fluoranthene. Strain CH1 also was capable of using a wide range of alkanes as sole carbon and energy sources. No DNA hybridization was detected with the nahAc gene probe, indicating that enzymes involved in PAH metabolism are not related to the well-characterized naphthalene dioxygenase gene. DNA hybridization was not detected when the alkB gene from Pseudomonas oleovorans was used under high-stringency conditions. However, there was slight but detectable hybridization under low-stringency conditions. This suggests a distant relationship between genes involved in alkane oxidation.

  14. Isolation and Characterization of a Mycobacterium Species Capable of Degrading Three- and Four-Ring Aromatic and Aliphatic Hydrocarbons

    PubMed Central

    Churchill, Sharon A.; Harper, Jennifer P.; Churchill, Perry F.

    1999-01-01

    Mycobacterium sp. strain CH1 was isolated from polycyclic aromatic hydrocarbon (PAH)-contaminated freshwater sediments and identified by analysis of 16S rDNA sequences. Strain CH1 was capable of mineralizing three- and four-ring PAHs including phenanthrene, pyrene, and fluoranthene. In addition, strain CH1 could utilize phenanthrene or pyrene as a sole carbon and energy source. A lag phase of at least 3 days was observed during pyrene mineralization. This lag phase decreased to less than 1 day when strain CH1 was grown in the presence of phenanthrene or fluoranthene. Strain CH1 also was capable of using a wide range of alkanes as sole carbon and energy sources. No DNA hybridization was detected with the nahAc gene probe, indicating that enzymes involved in PAH metabolism are not related to the well-characterized naphthalene dioxygenase gene. DNA hybridization was not detected when the alkB gene from Pseudomonas oleovorans was used under high-stringency conditions. However, there was slight but detectable hybridization under low-stringency conditions. This suggests a distant relationship between genes involved in alkane oxidation. PMID:9925581

  15. Characterization of Chlorinated Aliphatic Hydrocarbons and Environmental Variables in a Shallow Groundwater in Shanghai Using Kriging Interpolation and Multifactorial Analysis.

    PubMed

    Lu, Qiang; Luo, Qi Shi; Li, Hui; Liu, Yong Di; Gu, Ji Dong; Lin, Kuang Fei; Fei Lin, Kuang

    2015-01-01

    CAHs, as a cleaning solvent, widely contaminated shallow groundwater with the development of manufacturing in China's Yangtze River Delta. This study focused on the distribution of CAHs, and correlations between CAHs and environmental variables in a shallow groundwater in Shanghai, using kriging interpolation and multifactorial analysis. The results showed that the overall CAHs plume area (above DIV) was approximately 9,000 m(2) and located in the 2-4 m underground, DNAPL was accumulated at an area of approximately 1,400 m(2) and located in the 6-8m sandy silt layer on the top of the muddy silty clay. Heatmap of PPC for CAHs and environmental variables showed that the correlation between "Fe(2+)" and most CAHs such as "1,1,1-TCA", "1,1-DCA", "1,1-DCE" and "%TCA" were significantly positive (p<0.001), but "%CA" and/or "%VC" was not, and "Cl-" was significantly positive correlated with "1,1-DCA" and "1,1-DCE" (p<0.001). The PCA demonstrated that the relative proportions of CAHs in groundwater were mostly controlled by the sources and the natural attenuation. In conclusion, the combination of geographical and chemometrics was helpful to establishing an aerial perspective of CAHs and identifying reasons for the accumulation of toxic dechlorination intermediates, and could become a useful tool for characterizing contaminated sites in general. PMID:26565796

  16. Characterization of Chlorinated Aliphatic Hydrocarbons and Environmental Variables in a Shallow Groundwater in Shanghai Using Kriging Interpolation and Multifactorial Analysis

    PubMed Central

    Lu, Qiang; Luo, Qi Shi; Li, Hui; Liu, Yong Di; Gu, Ji Dong; Fei Lin, Kuang

    2015-01-01

    CAHs, as a cleaning solvent, widely contaminated shallow groundwater with the development of manufacturing in China's Yangtze River Delta. This study focused on the distribution of CAHs, and correlations between CAHs and environmental variables in a shallow groundwater in Shanghai, using kriging interpolation and multifactorial analysis. The results showed that the overall CAHs plume area (above DIV) was approximately 9,000 m2 and located in the 2–4 m underground, DNAPL was accumulated at an area of approximately 1,400 m2 and located in the 6-8m sandy silt layer on the top of the muddy silty clay. Heatmap of PPC for CAHs and environmental variables showed that the correlation between “Fe2+” and most CAHs such as “1,1,1-TCA”, “1,1-DCA”, “1,1-DCE” and “%TCA” were significantly positive (p<0.001), but “%CA” and/or “%VC” was not, and “Cl-” was significantly positive correlated with “1,1-DCA” and “1,1-DCE” (p<0.001). The PCA demonstrated that the relative proportions of CAHs in groundwater were mostly controlled by the sources and the natural attenuation. In conclusion, the combination of geographical and chemometrics was helpful to establishing an aerial perspective of CAHs and identifying reasons for the accumulation of toxic dechlorination intermediates, and could become a useful tool for characterizing contaminated sites in general. PMID:26565796

  17. Hydrocarbon and chlorinated hydrocarbon-soluble magnesium dialkoxides

    SciTech Connect

    Kamienski, C.W.

    1988-05-31

    This patent describes a process for the preparation of hydrocarbon or chlorinated hydrocarbon solvent solutions of magnesium dialkoxides, which comprises reacting a suspension of magnesium metal or magnesium amide, or a solution of a dialkyimagnesium compound, in a volatile hydrocarbon or chlorinated hydrocarbon solvent with an alcohol selected from the group of (a) aliphatic, cycloaliphatic and acyclic C/sub 5/-C/sub 18/ beta- and gamma-alkyl-substituted secondary and tertiary monohydric alcohols; or (b) mixtures of the (a) alcohols with C/sub 3/-C/sub 18/ aliphatic or cycloaliphatic beta- and gamma-alkyl-unsubstituted secondary or tertiary alcohols; or (c) mixtures of the (a) alcohols with C/sub 1/-C/sub 18/ aliphatic primary unsubstituted and 2-alkyl-substituted alcohols; the mole ratios of the (a) to the (b), and the (a) to the (c), alcohols being 1 of the (a) alcohols to 0.1 to 2 of the (b) and/or the (c) alcohols.

  18. Aliiglaciecola aliphaticivorans sp. nov., an aliphatic hydrocarbon-degrading bacterium, isolated from a sea-tidal flat and emended description of the genus Aliiglaciecola Jean et al. 2013.

    PubMed

    Jin, Hyun Mi; Jeong, Hye Im; Jeon, Che Ok

    2015-05-01

    A Gram-stain-negative heterotrophic bacterium, designated GSD6(T), capable of growth on aliphatic hydrocarbons as a sole carbon and energy source, was isolated from sea-tidal flat sediment of the Yellow Sea, South Korea. Cells were facultatively aerobic, catalase- and oxidase-positive, motile rods with a single polar flagellum. Growth of strain GSD6(T) was observed at 4-37 °C (optimum 30 °C), at pH 5.5-9.0 (optimum pH 6.5-7.5) and in the presence of 1-9% (w/v) NaCl (optimum 2%). Strain GSD6(T) contained ubiquinone-8 (Q-8) as the sole isoprenoid quinone and summed feature 3 (comprising C16 : 1ω7c and/or iso-C15 : 0 2-OH), C16 : 0, C18 : 1ω7c, C17  : 0 10-methyl and C17 : 1ω8c as the major fatty acids. Phosphatidylethanolamine and phosphatidylglycerol were identified as the major polar lipids. The G+C content of the genomic DNA was 44.6 mol%. Phylogenetic analysis based on 16S rRNA gene sequences showed that strain GSD6(T) formed a phylogenetic lineage with members of the genus Aliiglaciecola . Strain GSD6(T) was most closely related to Aliiglaciecola lipolytica E3(T) with a 16S rRNA gene sequence similarity of 97.4%, but their DNA-DNA hybridization value was 39.1 ± 7.1%. On the basis of phenotypic, chemotaxonomic and molecular features, strain GSD6(T) represents a novel species of the genus Aliiglaciecola , for which the name Aliiglaciecola aliphaticivorans sp. nov. is proposed. The type strain is GSD6(T) ( =KACC 18129(T) =JCM 30133(T)). An emended description of the genus Aliiglaciecola is also proposed. PMID:25713045

  19. Influence of soil and hydrocarbon properties on the solvent extraction of high-concentration weathered petroleum from contaminated soils.

    PubMed

    Sui, Hong; Hua, Zhengtao; Li, Xingang; Li, Hong; Wu, Guozhong

    2014-05-01

    Petroleum ether was used to extract petroleum hydrocarbons from soils collected from six oil fields with different history of exploratory and contamination. It was capable of fast removing 76-94 % of the total petroleum hydrocarbons including 25 alkanes (C11-C35) and 16 US EPA priority polycyclic aromatic hydrocarbons from soils at room temperature. The partial least squares analysis indicated that the solvent extraction efficiencies were positively correlated with soil organic matter, cation exchange capacity, moisture, pH, and sand content of soils, while negative effects were observed in the properties reflecting the molecular size (e.g., molecular weight and number of carbon atoms) and hydrophobicity (e.g., water solubility, octanol-water partition coefficient, soil organic carbon partition coefficient) of hydrocarbons. The high concentration of weathered crude oil at the order of 10(5) mg kg(-1) in this study was demonstrated adverse for solvent extraction by providing an obvious nonaqueous phase liquid phase for hydrocarbon sinking and increasing the sequestration of soluble hydrocarbons in the insoluble oil fractions during weathering. A full picture of the mass distribution and transport mechanism of petroleum contaminants in soils will ultimately require a variety of studies to gain insights into the dynamic interactions between environmental indicator hydrocarbons and their host oil matrix. PMID:24442962

  20. Solvent dewaxing waxy hydrocarbon distillates using a combination polyacrylate polymer and polymethacrylate polymer dewaxing aid

    SciTech Connect

    Briens, C.L.; Ewener, P.C.; Sankey, B.M.

    1984-05-29

    This invention relates to solvent dewaxing processes, for dewaxing waxy hydrocarbon oils using a dewaxing aid. The dewaxing aid comprises a mixture of (A) polyalkyl arcylate having alkyl group side chain length of from 10-26 carbons (excluding branching) and (B) an n-alkyl methacrylate polymer having alkyl group side chain length of from 10-20 carbons (excluding branching). Component (A) typically has a number average molecular weight of from 3,000 to 500,000 while component (B) typically has a number average molecular weight of from 5,000 to 200,000. The combination (A) plus (B) may be employed in a weight ratio within the range from about 1/100 to 100/1, preferably about 1/6 to 2/1 and at an aid does level ranging from about 0.01 wt % to 1 wt %, preferably 0.02 to 0.2 wt % active ingredient.

  1. IUPAC-NIST Solubility Data Series. 98. Solubility of Polycyclic Aromatic Hydrocarbons in Pure and Organic Solvent Mixtures: Revised and Updated. Part 1. Binary Solvent Mixtures

    NASA Astrophysics Data System (ADS)

    Acree, William E.

    2013-03-01

    This work updates Vols. 54, 58, and 59 in the IUPAC Solubility Data Series and presents solubility data for polycyclic aromatic hydrocarbon solutes dissolved in binary organic solvent mixtures. Published solubility data for anthracene, naphthalene, phenanthrene, phenothiazine, and pyrene that appeared in the primary literature between 1995 to the end of 2011 are compiled and critically evaluated. Experimental solubility data for 360 different solute-binary solvent systems are included in the volume. Solubility data published prior to 1995 were contained in three earlier volumes (Vols. 54, 58, and 59) and are not repeated in this volume.

  2. IUPAC-NIST Solubility Data Series. 98. Solubility of Polycyclic Aromatic Hydrocarbons in Pure and Organic Solvent Mixtures: Revised and Updated. Part 2. Ternary Solvent Mixtures

    NASA Astrophysics Data System (ADS)

    Acree, William E.

    2013-03-01

    This work updates Vols. 54, 58, and 59 in the IUPAC Solubility Data Series and presents solubility data for polycyclic aromatic hydrocarbon solutes dissolved in ternary organic solvent mixtures. Published solubility data for anthracene, phenanthrene, and pyrene that appeared in the primary literature between 1995 to the end of 2011 are compiled and critically evaluated. Experimental solubility data for 119 different solute-ternary solvent systems are included in the volume. Solubility data published prior to 1995 were contained in three earlier volumes (Vols. 54, 58, and 59) and are not repeated here.

  3. IUPAC-NIST Solubility Data Series. 98. Solubility of Polycyclic Aromatic Hydrocarbons in Pure and Organic Solvent Mixtures--Revised and Updated. Part 3. Neat Organic Solvents

    NASA Astrophysics Data System (ADS)

    Acree, William E.

    2013-03-01

    This work updates Vols. 54, 58, and 59 in the IUPAC Solubility Data Series and presents solubility data for polycyclic aromatic hydrocarbon solutes dissolved in neat organic solvents. Published solubility data for acenaphthene, anthracene, biphenyl, carbazole, dibenzofuran, dibenzothiophene, fluoranthene, fluorene, naphthalene, phenanthrene, phenothiazine, pyrene, thianthrene, and xanthene that appeared in the primary literature from 1995 to the end of 2011 are compiled and critically evaluated. Experimental solubility data for more than 550 different solute-organic solvent systems are included. Solubility data published prior to 1995 were contained in three earlier volumes (Vols. 54, 58, and 59) and are not repeated in this volume.

  4. Aliphatic hydrocarbons and polycyclic aromatic hydrocarbons (PAHs) in sediments collected from the 110 mile hole and along a transect from 58 degrees 58.32'N 1 degree 10.38'W to the inner Moray Firth, Scotland.

    PubMed

    Webster, Lynda; Twigg, Marsailidh; Megginson, Colin; Walsham, Pam; Packer, Gill; Moffat, Colin

    2003-06-01

    Sediments were collected from the 110 mile hole and along a transect from 58 degrees 58.32' N 1 degree 10.38' W to the UK National Marine Monitoring (NMMP) site in the inner Moray Firth, for determination of hydrocarbon concentration and composition. Total PAH concentrations (2- to 6-ring PAHs, parent and branched) were highest at NMMP site 95 and at the associated end of the transect in the inner Moray Firth. PAHs in this area were of predominately pyrolytic origin and could be attributed to urban and industrial activities. The majority of sediments collected in the middle section of the transect had low total PAH concentrations (< 100 ng g(-1) dry weight). The high proportion of naphthalenes and alkylated PAHs in this area suggested a predominately petrogenic input. The GC-FID aliphatic hydrocarbon profiles showed that the majority of sediments, including those in the inner Firth, had a limited petrogenic input. This was supported by the geochemical biomarker profiles, which contained triterpanes typical of Middle Eastern crude oil. Principal component analysis was used to investigate spatial trends in the PAH distributions and demonstrated that there were differences between areas. The NMMP site 95 and transect start and middle sediments were well separated. PCA further confirmed that sediments from the NMMP site 95, the 110 mile hole and the inner Moray Firth (south west) end of the transect contained PAHs from predominately pyrolytic sources, whereas sediments from the north east end (start) and the middle of the transect were typified by a greater petrogenic component. PMID:12833981

  5. Coal liquefaction process using pretreatment with a binary solvent mixture

    DOEpatents

    Miller, R.N.

    1986-10-14

    An improved process for thermal solvent refining or hydroliquefaction of non-anthracitic coal at elevated temperatures under hydrogen pressure in a hydrogen donor solvent comprises pretreating the coal with a binary mixture of an aromatic hydrocarbon and an aliphatic alcohol at a temperature below 300 C before the hydroliquefaction step. This treatment generally increases both conversion of coal and yields of oil. 1 fig.

  6. Evaluation of EpiDerm full thickness-300 (EFT-300) as an in vitro model for skin irritation: Studies on aliphatic hydrocarbons

    PubMed Central

    Mallampati, Ramya; Patlolla, Ram R.; Agarwal, Saurab; Babu, R. Jayachandra; Hayden, Patrick; Klausner, Mitchell; Singh, Mandip S.

    2010-01-01

    The aim of this study was to understand the skin irritation effects of saturated aliphatic hydrocarbons (HCs), C9–C16, found jet fuels using in vitro 3-dimensional EpiDerm full thickness-300 (EFT-300) skin cultures. The EFT-300 cultures were treated with 2.5 µl of HCs and the culture medium and skin samples were collected at 24 and 48 h to measure the release of various inflammatory biomarkers (IL-1α, IL-6 and IL-8). To validate the in vitro results, in vivo skin irritation studies were carried out in hairless rats by measuring trans epidermal water loss (TEWL) and erythema following un-occlusive dermal exposure of HCs for 72 h. The MTT tissue viability assay results with the EFT-300 tissue show that 2.5 µl/tissue (≈4.1 µl/cm2) of the HCs did not induce any significant changes in the tissue viability for exposure times up to 48 h of exposure. Microscopic observation of the EFT-300 cross-sections indicated that there were no obvious changes in the tissue morphology of the samples at 24 h, but after 48 h of exposure, tridecane, tetradecane and hexadecane produced a slight thickening and disruption of stratum corneum. Dermal exposures of C12–C16 HCs for 24 h significantly increased the expression of IL-1α in the skin as well as in the culture medium. Similarly, dermal exposure of all HCs for 24 h significantly increased the expression of interleukin-6 (IL-6) and IL-8 in the skin as well as in the culture medium in proportion to the HC chain length. As the exposure time increased to 48 h, IL-6 concentrations increased 2-fold compared to the IL-6 values at 24 h. The in vivo skin irritation data also showed that both TEWL and erythema scores increased with increased HCs chain length (C9–C16). In conclusion, the EFT-300 showed that the skin irritation profile of HCs was in the order of C9 ≤ C10 ≤ C11 ≤ C12 < C13 ≈ C14 ≈ C16 and that the tissue was an excellent in vitro model to predict in vivo irritation and to understand the structural activity

  7. Microbial diversity in a hydrocarbon- and chlorinated-solvent- contaminated aquifer undergoing intrinsic bioremediation

    USGS Publications Warehouse

    Dojka, M.A.; Hugenholtz, P.; Haack, S.K.; Pace, N.R.

    1998-01-01

    A culture-independent molecular phylogenetic approach was used to survey constituents of microbial communities associated with an aquifer contaminated with hydrocarbons (mainly jet fuel) and chlorinated solvents undergoing intrinsic bioremediation. Samples were obtained from three redox zones: methanogenic, methanogenic-sulfate reducing, and iron or sulfate reducing. Small-subunit rRNA genes were amplified directly from aquifer material DNA by PCR with universally conserved or Bacteria- or Archaea-specific primers and were cloned. A total of 812 clones were screened by restriction fragment length polymorphisms (RFLP), approximately 50% of which were unique. All RFLP types that occurred more than once in the libraries, as well as many of the unique types, were sequenced. A total of 104 (94 bacterial and 10 archaeal) sequence types were determined. Of the 94 bacterial sequence types, 10 have no phylogenetic association with known taxonomic divisions and are phylogenetically grouped in six novel division level groups (candidate divisions WS1 to WS6); 21 belong to four recently described candidate divisions with no cultivated representatives (OPS, OP8, OP10, and OP11); and 63 are phylogenetically associated with 10 well-recognized divisions. The physiology of two particularly abundant sequence types obtained from the methanogenic zone could be inferred from their phylogenetic association with groups of microorganisms with a consistent phenotype. One of these sequence types is associated with the genus Syntrophus; Syntrophus spp. produce energy from the anaerobic oxidation of organic acids, with the production of acetate and hydrogen. The organism represented by the other sequence type is closely related to Methanosaeta spp., which are known to be capable of energy generation only through aceticlastic methanogenesis. We hypothesize, therefore, that the terminal step of hydrocarbon degradation in the methanogenic zone of the aquifer is aceticlastic methanogenesis and

  8. An assessment of natural biotransformation of petroleum hydrocarbons and chlorinated solvents at an aquifer plume transect.

    PubMed

    Skubal, K L; Barcelona, M J; Adriaens, P

    2001-05-01

    Field biogeochemical characterization and laboratory microcosm studies were performed to assess the potential for future biotransformation of trichloroethylene (TCE) and toluene in a plume containing petroleum hydrocarbons and chlorinated solvents at the former Wurtsmith Air Force Base in Oscoda, MI. In situ terminal electron accepting processes (TEAPs), contaminant composition and microbial phylogeny were studied at a plume transect 100 m downgradient of the source. The presence of reduced electron acceptors, relevant microbial communities, and elevated dissolved methane and carbon dioxide concentrations at the transect, as well as downgradient accumulation of BTEX metabolites and dechlorination products, indicated that past or current reductive dechlorination at the transect was likely driven by BTEX biodegradation in the methanogenic zone. However, TCE and toluene mineralization in sediment-groundwater microcosms without added electron acceptors did not exceed 5% during 300 days of incubation and was nearly invariant with original sediment TEAP, even following amendments of nitrogen and phosphorus. Mineralization rates were on the order of 0.0015-0.03 mumol/g day. After 8 months, microcosms showed evidence of methanogenesis, but CH4 and CO2 production arose from the degradation of contaminants other than toluene. Cis-dichloroethylene was observed in only one methanogenic microcosm after more than 500 days. It appears likely that spatially and temporally dynamic redox zonation at the plume transect will prevent future sustained reductive dehalogenation of highly chlorinated solvents, for during the course of a year, the predominant TEAP at the highly contaminated water table shifted from methanogenesis to iron- and sulfate-reduction. It is recommended that biotransformation studies combine considerations of long-term, spatially relevant changes in redox zonation with laboratory-scale studies of electron donor utilization and cometabolic substrate transformation

  9. Hydrocarbons preserved in a ~2.7 Ga outcrop sample from the Fortescue Group, Pilbara Craton, Western Australia.

    PubMed

    Hoshino, Y; Flannery, D T; Walter, M R; George, S C

    2015-03-01

    The hydrocarbons preserved in an Archean rock were extracted, and their composition and distribution in consecutive slices from the outside to the inside of the rock were examined. The 2.7 Ga rock was collected from the Fortescue Group in the Pilbara region, Western Australia. The bitumen I (solvent-extracted rock) and bitumen II (solvent-extracted hydrochloric acid-treated rock) fractions have different hydrocarbon compositions. Bitumen I contains only trace amounts of aliphatic hydrocarbons and virtually no aromatic hydrocarbons. In contrast, bitumen II contains abundant aliphatic and aromatic hydrocarbons. The difference seems to reflect the weathering history and preservational environment of the investigated rock. Aliphatic hydrocarbons in bitumen I are considered to be mainly from later hydrocarbon inputs, after initial deposition and burial, and are therefore not indigenous. The lack of aromatic hydrocarbons in bitumen I suggests a severe weathering environment since uplift and exposure of the rock at the Earth's surface in the Cenozoic. On the other hand, the high abundance of aromatic hydrocarbons in bitumen II suggests that bitumen II hydrocarbons have been physically isolated from removal by their encapsulation within carbonate minerals. The richness of aromatic hydrocarbons and the relative scarcity of aliphatic hydrocarbons may reflect the original compositions of organic materials biosynthesised in ancient organisms in the Archean era, or the high thermal maturity of the rock. Cyanobacterial biomarkers were observed in the surficial slices of the rock, which may indicate that endolithic cyanobacteria inhabited the surface outcrop. The distribution of aliphatic and aromatic hydrocarbons implies a high thermal maturity, which is consistent with the lack of any specific biomarkers, such as hopanes and steranes, and the prehnite-pumpellyite facies metamorphic grade. PMID:25393450

  10. Electron-accepting potential of solvents determines photolysis rates of polycyclic aromatic hydrocarbons: experimental and density functional theory study.

    PubMed

    Shao, Jianping; Chen, Jingwen; Xie, Qing; Wang, Ying; Li, Xuehua; Hao, Ce

    2010-07-15

    Photochemical behaviour of polycyclic aromatic hydrocarbons (PAHs) is strongly dependent on the physical and chemical nature of the media in/on which they exist. To understand the media effects, the photolysis of phenanthrene (PHE) and benzo[a]pyrene (BaP) in several solvents was investigated. Distinct photolysis rate constants for PHE and BaP in the different solvents were observed. Some theoretical parameters reflecting the solvent properties were computed and employed to explain the solvent effects. Acetone competitively absorbed light with PHE and BaP, and the excited acetone molecules played different roles for the photodegradation of PHE and BaP. The photolysis rate constants of PHE and BaP in hexane, isopropanol, ethanol, methanol, acetonitrile and dichloromethane were observed to correlate with the electron-accepting potential of the solvent molecules. Absolute electronegativity of the solvents linearly correlated with the photolytic activity (log k) of the PAHs significantly. The results are important for better understanding the photodegradation mechanism of PAHs in different media. PMID:20303660

  11. Comparison of aliphatic hydrocarbons, polycyclic aromatic hydrocarbons, polychlorinated biphenyls, polybrominated diphenylethers, and organochlorine pesticides in Pacific sanddab (Citharichthys sordidus) from offshore oil platforms and natural reefs along the California coast

    USGS Publications Warehouse

    Gale, Robert W.; Tanner, Michael J.; Love, Milton S.; Nishimoto, Mary M.; Schroeder, Donna M.

    2013-01-01

    Recently, the relative exposure of Pacific sanddab (Citharichthys sordidus) to polycyclic aromatic hydrocarbons (PAHs) at oil-production platforms was reported, indicating negligible exposure to PAHs and no discernible differences between exposures at platforms and nearby natural areas sites. In this report, the potential for chronic PAH exposure in fish is reported, by measurement of recalcitrant, higher molecular weight PAHs in tissues of fish previously investigated for PAH metabolites in bile. A total of 34 PAHs (20 PAHs, 11 alkylated PAHs, and 3 polycyclic aromatic thiophenes) were targeted. In addition, legacy contaminants—polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs),—and current contaminants, polybrominated diphenylethers (PBDEs) linked to endocrine disruption, were measured by gas chromatography with electron-capture or mass spectrometric detection, to form a more complete picture of the contaminant-related status of fishes at oil production platforms in the Southern California Bight. No hydrocarbon profiles or unresolved complex hydrocarbon background were found in fish from platforms and from natural areas, and concentrations of aliphatics were low less than 100 nanograms per gram (ng/g) per component]. Total-PAH concentrations in fish ranged from 15 to 37 ng/g at natural areas and from 8.7 to 22 ng/g at platforms. Profiles of PAHs were similar at all natural and platform sites, consisting mainly of naphthalene and methylnaphthalenes, phenanthrene, fluoranthene, and pyrene. Total-PCB concentrations (excluding non-ortho-chloro-substituted congeners) in fish were low, ranging from 7 to 22 ng/g at natural areas and from 10 to 35 ng/g at platforms. About 50 percent of the total-PCBs at all sites consisted of 11 congeners: 153 > 138/163/164 > 110 > 118 > 15 > 99 > 187 > 149 > 180. Most OCPs, except dichlorodiphenyltrichloroethane (DDT)-related compounds, were not detectable or were at concentrations of less than 1 ng/g in fish. p

  12. Polar solvent structural parameters from protonation equilibria of aliphatic and alicyclic diamines and from absorption bands of mixed-valence transition-metal complexes

    NASA Astrophysics Data System (ADS)

    Kornyshev, A. A.; Ulstrup, J.

    1986-04-01

    We have applied non-local electrostatic theory in combination with a simple solute model to obtain solvent structural properties in terms of the short-range dielectric constant, ˜ge, and the correlation length for the solvent polarization fluctuations, A. These parameters are fitted to experimental data for the free energy of interaction between protonated amino groups in dibasic amines and for intervalence band maxima of binuclear ruthenium complexes with bridge groups of varying length. The results show that non-local screening in the outer solvent, ˜ge in the range 3.5-4 for water, and A ≈ 2-3 Å and 4 Å for acetonitrile and water, respectively, provide good fits to the data, implying the significance of solvent structural effects for these phenomena.

  13. Nonhazardous solvent composition and method for cleaning metal surfaces

    DOEpatents

    Googin, John M.; Simandl, Ronald F.; Thompson, Lisa M.

    1993-01-01

    A solvent composition for displacing greasy and oily contaminants as well as water and/or aqueous residue from metallic surfaces, especially surfaces of radioactive materials so that such surfaces can be wiped clean of the displaced contaminants, water and/or aqueous residue. The solvent composition consists essentially of a blend of nonpolar aliphatic hydrocarbon solvent having a minimum flash point of about 140.degree. F. and 2 to 25 volume percent of a polar solvent having a flash point sufficiently high so as to provide the solvent composition with a minimum flash point of at least 140.degree. F. The solvent composition is nonhazardous so that when it is used to clean the surfaces of radioactive materials the waste in the form of paper or cloth wipes, lab coats and the like used in the cleaning operation is not considered to be mixed waste composed of a hazardous solvent and a radioactive material.

  14. Nonhazardous solvent composition and method for cleaning metal surfaces

    DOEpatents

    Googin, J.M.; Simandl, R.F.; Thompson, L.M.

    1993-05-04

    A solvent composition for displacing greasy and oily contaminants as well as water and/or aqueous residue from metallic surfaces, especially surfaces of radioactive materials so that such surfaces can be wiped clean of the displaced contaminants, water and/or aqueous residue. The solvent composition consists essentially of a blend of nonpolar aliphatic hydrocarbon solvent having a minimum flash point of about 140 F and 2 to 25 volume percent of a polar solvent having a flash point sufficiently high so as to provide the solvent composition with a minimum flash point of at least 140 F. The solvent composition is nonhazardous so that when it is used to clean the surfaces of radioactive materials the waste in the form of paper or cloth wipes, lab coats and the like used in the cleaning operation is not considered to be mixed waste composed of a hazardous solvent and a radioactive material.

  15. Recovery of solvent in hydrocarbon processing systems. [N-methyl-2pyrrolidone

    SciTech Connect

    Sherman, P.B.

    1983-06-28

    This is a claim for a lubricating oil solvent refining process employing n-methyl-2pyrrolidone as solvent in which solvent is recovered from a solvent-oil mixture in a staged series of vaporization zones at progressively increasing pressure with external heat supplied only to the vaporization stage having the highest pressure. Control of vaporization in the lower pressure stages is effected by passing a minor portion of the vapors from the highest pressure stage to the lowest pressure stage. A high temperature vacuum flash vaporization zone may follow the high pressure vaporization stage with external heat supplied to the vacuum flash vaporization zone.

  16. Assessment of the availability of polycyclic aromatic hydrocarbons from gasworks soil using different extraction solvents and techniques.

    PubMed

    Bergknut, Magnus; Kitti, Anna; Lundstedt, Staffan; Tysklind, Mats; Haglund, Peter

    2004-08-01

    This study was designed to assess the availability of polycyclic aromatic hydrocarbons (PAHs) present at a gasworks site to different soil remediation techniques. The study examined the effect on PAH availability of using different organic solvents, the degree of pretreatment, and the extraction time. In total, 25 PAHs (with two to six fused rings) and five carbonyl derivatives were measured. The results indicated that the PAHs and their derivatives were bound loosely to the surface of the studied soil and that there were no significant kinetic boundaries associated with the extraction of the PAHs. Furthermore, it was concluded that the studied soil was not suitable for bioremediation, as the concentration of PAHs with low molecular weight were limited. However, pressurized liquid extraction (PLE) with methanol as the solvent extracted 97% of all PAHs and PAH-derivatives, indicating that extraction may be effective as part of a soil remediation technique for old gasworks soils. PMID:15352473

  17. Comparison of rapid solvent extraction systems for the GC–MS/MS characterization of polycyclic aromatic hydrocarbons in aged, contaminated soil

    PubMed Central

    Haleyur, Nagalakshmi; Shahsavari, Esmaeil; Mansur, Abdulatif A.; Koshlaf, Eman; Morrison, Paul D.; Osborn, A. Mark; Ball, Andrew S.

    2016-01-01

    Polycyclic aromatic hydrocarbons (PAHs) are a major class of organic hydrocarbons with high molecular weight that originate from both natural and anthropogenic sources. Sixteen PAHs are included in the U.S Environmental Protection agency list of priority pollutants due to their mutagenic, carcinogenic, toxic and teratogenic properties. In this study, the development and optimization of a simplified and rapid solvent extraction for the characterisation of 16 USEPA priority poly aromatic hydrocarbons (PAHs) in aged contaminated soils was established with subsequent analysis by GC–MS/MS. • Five different extraction solvent systems: dichloromethane: acetone, chloroform: methanol, dichloromethane, acetone: hexane and hexane were assessed in terms of their ability to extract PAHs from aged PAH-contaminated soils. • Highest PAH concentrations were extracted using acetone: hexane and chloroform: methanol. Given the greater toxicity associated with chloroform: methanol, acetone: hexane appears the best choice of solvent extraction system. • This protocol enables efficient extraction of PAHs from aged weathered soils. PMID:27200269

  18. Hydrocarbon soluble polymer complexes useful as viscosifiers in fracturing operations

    SciTech Connect

    Sedillo, L.P.; Newlove, J.C.; Peiffer, D.G.; Lundberg, R.D.

    1986-10-07

    A process is described for fracturing a subterranean formation surrounding a gas or oil well which comprises injecting into the subterranean formation under hydraulic pressure a fluid comprising about 0.01 to about 25 weight percent of a water insoluble polymer complex dissolved in a solvent system comprising a nonpolar organic liquid. The polymer complex comprises the interaction product of a metal neutralized sulfonated polymer and an amine containing polymer. The sulfonate content of the sulfonated polymer is about 4 meq. per 100 grams of polymer to about 100 meq. per 100 gram of polymer and the basic nitrogen content of the amine containing polymer is about 4 meq. per 100 gram of polymer to about 500 meq. per 100 gram of polymer. The organic liquid is selected from the group consisting of paraffinic hydrocarbons, naphthenic hydrocarbons, aromatic hydrocarbons, ketones, chlorinated aliphatic hydrocarbons, cyclic aliphatic ethers, aliphatic ethers and organic aliphatic esters and mixtures thereof. The amine containing polymer is a copolymer of vinyl-pyridine with other vinyl monomers which are selected from the group consisting of acrylates, methacrylates, alkyl acrylates, alkyl methacrylates, N-alkylacrylamide and N-alkylmethacrylamides and mixtures thereof, the acrylates or methacrylates, etc. having from about 6 to about 26 carbon atoms.

  19. Synergistic effects in solvent-extraction systems based on alkylsalicylic acids. I. Extraction of trivalent rare-earth metals in the presence of aliphatic amides

    SciTech Connect

    Preston, J.S.; Preez, A.C. du

    1995-07-01

    Aliphatic carboxylic acid amides were found to cause synergistic shifts in the pH{sub 50} values for the extraction of the trivalent rare-earth metals from chloride media by solutions of alkylsalicylic acids in xylene. For the different types of amide examined, the synergistic shifts for the extraction of neodymium by 3,5-diisopropylsalicylic acid (DIPSA) generally decrease in the order: R.CO.NR{sub 2}` > R.CO.NHR` > R.CO.NH{sub 2}, where R and R` are alkyl groups. With the N,N-dialkyl amides (R.CO.NR{sub 2}`) and the N-alkyl amides (R.CO.NHR`), the extent of the synergistic effect decreases with increasing chain-branching in either of the alkyl groups R and R`. For additions to 0.25 M alkylsalicylic acid, the synergistic effect increases with concentrations of up to 0.1 M amide, and decreases with higher concentrations. The extent of the synergistic shift produced by a given amide, as well as the separation in pH{sub 50} values from lanthanum to lutetium, increases with increasing steric bulk of the alkylsalicylic acid used. The separations between adjacent lanthanides are too small to be of any practical interest, however. Measurement of the solubility of salicylic acids (HA) in xylene containing various amounts of N,N-dialkyl amide (L) indicate that essentially complete formation of the HA.L adduct takes place. Treatment of metal-distribution data by slope analysis, and measurement of the solubility of the neodymium-DIPSA complex in xylene in the presence of amide suggest that the mixed-ligand complex has the stoichiometry NdA{sub 3}L{sub 2}. 18 refs., 6 figs., 3 refs.

  20. DETERMINATION OF SOLID-LIQUID EQUILIBRIA DATA FOR MIXTURES OF HEAVY HYDROCARBONS IN A LIGHT SOLVENT

    SciTech Connect

    F.V. Hanson; J.V. Fletcher; Karthik R.

    2003-06-01

    A methodology was developed using an FT-IR spectroscopic technique to obtain solid-liquid equilibria (SLE) data for mixtures of heavy hydrocarbons in significantly lighter hydrocarbon diluents. SLE was examined in multiple Model Oils that were assembled to simulate waxes. The various Model oils were comprised of C-30 to C-44 hydrocarbons in decane. The FT-IR technique was used to identify the wax precipitation temperature (WPT). The DSC technique was also used in the identification of the onset of the two-phase equilibrium in this work. An additional Model oil made up of C-20 to C-30 hydrocarbons in decane was studied using the DSC experiment. The weight percent solid below the WPT was calculated using the FT-IR experimental results. The WPT and the weight percent solid below the WPT were predicted using an activity coefficient based thermodynamic model. The FT-IR spectroscopy method is found to successfully provide SLE data and also has several advantages over other laboratory-based methods.

  1. Stabilization of asphaltenes in aliphatic solvents using alkylbenzene-derived amphiphiles. 1. Effect of the chemical structure of amphiphiles on asphaltene stabilization

    SciTech Connect

    Chang, C.L.; Fogler, H.S. )

    1994-06-01

    Stabilization of crude oil asphaltenes in apolar alkane solvents was investigated using a series of alkylbenzene-derived amphiphiles as the asphaltene stabilizers. In this paper (i.e., part I), we present the study on the influences of the chemical structure of these amphiphiles on the effectiveness of asphaltene solubilization and on the strength of asphaltene-amphiphile interaction using both UV/vis and FTIR spectroscopies. The results showed that the amphiphile's effectiveness of asphaltene stabilization was primarily controlled by the polarity of the amphiphile's head group and the length of the amphiphile's alkyl tail. Increasing the acidity of the amphiphile's head group could promote the amphiphile's ability to stabilize asphaltenes by increasing the acid-base attraction between asphaltenes and amphiphiles. On the other hand, although decreasing the amphiphile's tail length increased the asphaltene-amphiphile attraction slightly, it still required a minimum tail length (six carbons for p-alkylphenol amphiphiles) for amphiphiles to form stable steric layers around asphaltenes. We also found additional acidic side groups of amphiphiles could further improve the amphiphile's ability to stabilize asphaltenes. The effect of the molecular weight of alkane solvents on the amphiphile's ability to stabilize asphaltenes was also studied. 18 refs., 12 figs., 3 tabs.

  2. Biodegradation by an Arthrobacter species of hydrocarbons partitioned into an organic solvent

    SciTech Connect

    Efroymson, R.A.; Alexander, M. )

    1991-05-01

    An Arthrobacter strain mineralized naphthalene and n-hexadecane dissolved in 2,2,4,4,5,6,6-heptamethylnonane. The extent of mineralization increased with greater volumes of solvent. The rate of mineralization of hexadecone was rapid, although partitioning of the compound into aqueous solution was not detected. The Arthrobacter sp. grown in media with or without heptamethylnonane did not excrete products that increased the aqueous solubility of naphthalene and hexadecane. Measurements of the number of cells in the aqueous phase showed that the Arthrobacter sp. attached to the heptamethylnonane-water interface, but attachment was evident even without a substrate in the heptamethylnonane. Tests with small inocula of the Arthrobacter sp. demonstrated that at least a portion of naphthalene or hexadecane dissolved in heptamethylnonane was degraded by cells attached to the solvent-water interface. The cells did not adhere in the presence of 0.1% Triton X-100. The surfactant prevented mineralization of the hexadecane initially dissolved in heptamethylnonene, but it increased the rate and extent of mineralization of naphthalene initially dissolved in heptamethylnonane. The data show that organic solvents into which hydrophobic compounds partition affect the biodegradation of those compounds and that attachment of microorganisms to the organic solvent-water interface may be important in the transformation.

  3. Nitrogen incorporation in saturated aliphatic C6-C8 hydrocarbons and ethanol in low-pressure nitrogen plasma generated by a hollow cathode discharge ion source.

    PubMed

    Usmanov, Dilshadbek T; Chen, Lee Chuin; Hiraoka, Kenzo; Wada, Hiroshi; Nonami, Hiroshi; Yamabe, Shinichi

    2016-06-01

    Ion/molecule reactions of saturated hydrocarbons (n-hexane, cyclohexane, n-heptane, n-octane and isooctane) in 28-Torr N2 plasma generated by a hollow cathode discharge ion source were investigated using an Orbitrap mass spectrometer. It was found that the ions with [M+14](+) were observed as the major ions (M: sample molecule). The exact mass analysis revealed that the ions are nitrogenated molecules, [M+N](+) formed by the reactions of N3 (+) with M. The reaction, N3 (+) + M → [M+N](+) + N2 , were examined by the density functional theory calculations. It was found that N3 (+) abstracts the H atom from hydrocarbon molecules leading to the formation of protonated imines in the forms of R'R″CNH2 (+) (i.e. C-H bond nitrogenation). This result is in accord with the fact that elimination of NH3 is the major channel for MS/MS of [M+N](+) . That is, nitrogen is incorporated in the C-H bonds of saturated hydrocarbons. No nitrogenation was observed for benzene and acetone, which was ascribed to the formation of stable charge-transfer complexes benzene⋅⋅⋅⋅N3 (+) and acetone⋅⋅⋅⋅N3 (+) revealed by density functional theory calculations. Copyright © 2016 John Wiley & Sons, Ltd. PMID:27270868

  4. Geochemical markers and polycyclic aromatic hydrocarbons in solvent extracts from diesel engine particulate matter.

    PubMed

    Fabiańska, Monika; Kozielska, Barbara; Bielaczyc, Piotr; Woodburn, Joseph; Konieczyński, Jan

    2016-04-01

    Exhaust particulate from compression ignition (CI) engines running on engine and chassis dynamometers was studied. Particulate dichloromethane extracts were qualitatively and quantitatively analyzed for polycyclic aromatic hydrocarbons (PAHs) and biomarkers by gas chromatography with flame ionization detector (GC-FID) and gas chromatography-mass spectrometry (GC-MS). PAH group profiles were made and the PAH group shares according to the number of rings (2 or 3; 4; 5 or more) as well as diagnostic indices were calculated. Values of geochemical ratios of selected biomarkers and alkyl aromatic hydrocarbons were compared with literature values. A geochemical interpretation was carried out using these values and biomarker and alkyl aromatic hydrocarbon distributions. It has been shown that geochemical features are unequivocally connected to the emission of fossil fuels and biofuels burned in CI engines. The effect of the exothermic combustion process is limited to low-molecular-weight compounds, which shows that the applied methodology permits source identification of PAHs coexisting in the particulate emitted. PMID:26728284

  5. The use of solvent extractions and solubility theory to discern hydrocarbon associations in coal, with application to the coal-supercritical CO2 system

    USGS Publications Warehouse

    Kolak, Jonathan J.; Burruss, Robert A.

    2014-01-01

    Samples of three high volatile bituminous coals were subjected to parallel sets of extractions involving solvents dichloromethane (DCM), carbon disulfide (CS2), and supercritical carbon dioxide (CO2) (40 °C, 100 bar) to study processes affecting coal–solvent interactions. Recoveries of perdeuterated surrogate compounds, n-hexadecane-d34 and four polycyclic aromatic hydrocarbons (PAHs), added as a spike prior to extraction, provided further insight into these processes. Soxhlet-DCM and Soxhlet-CS2 extractions yielded similar amounts of extractable organic matter (EOM) and distributions of individual hydrocarbons. Supercritical CO2 extractions (40 °C, 100 bar) yielded approximately an order of magnitude less EOM. Hydrocarbon distributions in supercritical CO2 extracts generally mimicked distributions from the other solvent extracts, albeit at lower concentrations. This disparity increased with increasing molecular weight of target hydrocarbons. Five- and six-ring ring PAHs generally were not detected and no asphaltenes were recovered in supercritical CO2 extractions conducted at 40 °C and 100 bar. Supercritical CO2 extraction at elevated temperature (115 °C) enhanced recovery of four-ring and five-ring PAHs, dibenzothiophene (DBT), and perdeuterated PAH surrogate compounds. These results are only partially explained through comparison with previous measurements of hydrocarbon solubility in supercritical CO2. Similarly, an evaluation of extraction results in conjunction with solubility theory (Hildebrand and Hansen solubility parameters) does not fully account for the hydrocarbon distributions observed among the solvent extracts. Coal composition (maceral content) did not appear to affect surrogate recovery during CS2 and DCM extractions but might affect supercritical CO2 extractions, which revealed substantive uptake (partitioning) of PAH surrogates into the coal samples. This uptake was greatest in the sample (IN-1) with the highest vitrinite content. These

  6. Influence of Solvent-Like Sidechains on the Adsorption of Light Hydrocarbons in Metal-Organic Frameworks.

    PubMed

    Schneemann, Andreas; Bloch, Eric D; Henke, Sebastian; Llewellyn, Philip L; Long, Jeffrey R; Fischer, Roland A

    2015-12-14

    A variety of strategies have been developed to adsorb and separate light hydrocarbons in metal-organic frameworks. Here, we present a new approach in which the pores of a framework are lined with four different C3 sidechains that feature various degrees of branching and saturation. These pendant groups, which essentially mimic a low-density solvent with restricted degrees of freedom, offer tunable control of dispersive host-guest interactions. The performance of a series of frameworks of the type Zn2 (fu-bdc)2 (dabco) (fu-bdc(2-) =functionalized 1,4-benzenedicarboxylate; dabco=1,4-diazabicyclo[2.2.2]octane), which feature a pillared layer structure, were investigated for the adsorption and separation of methane, ethane, ethylene, and acetylene. The four frameworks exhibit low methane uptake, whereas C2 hydrocarbon uptake is substantially higher as a result of the enhanced interaction of these molecules with the ligand sidechains. Most significantly, the adsorption quantities and selectivity were found to depend strongly upon the type of sidechains attached to the framework scaffold. PMID:26559500

  7. Evidence for a critical micelle concentration of surfactants in hydrocarbon solvents.

    PubMed

    Smith, Gregory N; Brown, Paul; Rogers, Sarah E; Eastoe, Julian

    2013-03-12

    The concentration-dependent aggregation of two surfactants, anionic sodium dioctylsulfosuccinate (Aerosol OT or AOT) and nonionic pentaethylene glycol monododecyl ether (C12E5), has been studied in cyclohexane-D12 using small-angle neutron scattering (SANS). A clear monomer-to-aggregate transition has been observed for both surfactants, spherical inverse micelles for AOT and hank-like micelles for C12E5. This suggests that a critical micelle concentration exists for surfactants of these kinds in nonpolar solvents. The nature of the transition is different for the two surfactants. AOT aggregates are the same size and shape with decreasing concentration until a sharp critical micelle concentration, after which they cannot be detected. However, C12E5 aggregates gradually decrease in size. These differences demonstrate that the strength of the solvophobic effect can influence the formation of surfactant aggregates in nonaqueous solvents. PMID:23410112

  8. Degradation problems with the solvent extraction organic at Roessing uranium

    SciTech Connect

    Munyungano, Brodrick; Feather, Angus; Virnig, Michael

    2008-07-01

    Roessing Uranium Ltd recovers uranium from a low-grade ore in Namibia. Uranium is recovered and purified from an ion-exchange eluate in a solvent-extraction plant. The solvent-extraction plant uses Alamine 336 as the extractant for uranium, with isodecanol used as a phase modifier in Sasol SSX 210, an aliphatic hydrocarbon diluent. Since the plant started in the mid 1970's, there have been a few episodes where the tertiary amine has been quickly and severely degraded when the plant was operated outside certain operating parameters. The Rossing experience is discussed in more detail in this paper. (authors)

  9. Preparation and use of tetra-alkyl cobalt dicarbollide for extraction of cesium and strontium into hydrocarbon solvents

    DOEpatents

    Miller, R.L.; Pinkerton, A.B.; Abney, K.D.; Kinkead, S.A.

    1997-02-11

    Preparation and use of tetra-C-alkyl cobalt dicarbollide for extraction of cesium and strontium into hydrocarbon solvents. Tetra-C-alkyl derivatives of cobalt dicarbollide, Co(C{sub 2}R{sub 2}B{sub 9}H{sub 9}){sub 2}{sup {minus}}(CoB{sub 2}R{sub 4}{sup {minus}}; R=CH{sub 3} and C{sub 6}H{sub 13}) are demonstrated to be significant cesium and strontium extractants from acidic and alkaline solutions into non-toxic organic solvent systems. Extractions using mesitylene and diethylbenzene are compared to those with nitrobenzene as the organic phase. CoB{sub 2}-hexyl{sub 4}{sup {minus}} in diethylbenzene shows improved selectivity (10{sup 4}) for Cs over Na in acidic solution. In dilute alkaline solution, CoB{sub 2}-hexyl{sub 4}{sup {minus}} extracts Cs less efficiently, but more effectively removes Sr from higher base concentrations. A general synthesis of tetra-C-alkyl cobalt dicarbollides is described. 6 figs.

  10. Preparation and use of tetra-alkyl cobalt dicarbollide for extraction of cesium and strontium into hydrocarbon solvents

    DOEpatents

    Miller, Rebecca L.; Pinkerton, Anthony B.; Abney, Kent D.; Kinkead, Scott A.

    1997-01-01

    Preparation and use of tetra-C-alkyl cobalt dicarbollide for extraction of cesium and strontium into hydrocarbon solvents. Tetra-C-alkyl derivatives of cobalt dicarbollide, Co(C.sub.2 R.sub.2 B.sub.9 H.sub.9).sub.2.sup.- (CoB.sub.2 R.sub.4.sup.- ; R=CH.sub.3 and C.sub.6 H.sub.13) are demonstrated to be significant cesium and strontium extractants from acidic and alkaline solutions into non-toxic organic solvent systems. Extractions using mesitylene and diethylbenzene are compared to those with nitrobenzene as the organic phase. CoB.sub.2 -hexyl.sub.4.sup.- in diethylbenzene shows improved selectivity (10.sup.4) for Cs over Na in acidic solution. In dilute alkaline solution, CoB.sub.2 -hexyl.sub.4.sup.- extracts Cs less efficiently, but more effectively removes Sr from higher base concentrations. A general synthesis of tetra-C-alkyl cobalt dicarbollides is described.

  11. PHOTOCHEMICAL REACTION OF NITRO-POLYCYCLIC AROMATIC HYDROCARBONS: EFFECT BY SOLVENT AND STRUCTURE

    PubMed Central

    Stewart, Gernerique; Smith, Keonia; Chornes, Ashley; Harris, Tracy; Honeysucker, Tiffany; Dasary, Suman Raj; Yu, Hongtao

    2010-01-01

    Photochemical degradation of 1-nitropyrene, 2-nitrofluorene, 2,7-dinitrofluorene, 6-nitrochrysene, 3-nitrofluoranthene, 5-nitroacenaphthene, and 9-nitroanthracene were examined in CHCl3, CH2Cl2, DMF, DMF/H2O (80/20), CH3CN, or CH3CN/H2O (80/20). The degradation follows mostly the 1st order kinetics; but a few follow 2nd order kinetics or undergo self-catalysis. The photodegradation rates follow the order: CHCl3 > CH2Cl2 > DMF > DMF/H2O > CH3CN > CH3CN/H2O. DMF is an exceptional solvent because 3 of the 7 compounds undergo self-catalytic reaction. 9-Nitroanthracene, which has a perpendicular nitro group, is the fastest, while the more compact 1-nitropyrene and 3-nitrofluoranthene, are the slowest degrading compounds. PMID:21170286

  12. Aqueous accelerated solvent extraction of native polycyclic aromatic hydrocarbons (PAHs) from carbonaceous river floodplain soils.

    PubMed

    Yang, Yi; Hofmann, Thilo

    2009-10-01

    In this study, three river floodplain soils with different compositions of carbonaceous materials and a reference coal sample were extracted with water using the accelerated solvent extraction (ASE) method. The desorption enthalpy values for 2-ring PAHs were highest in the coal sample, with values in the soil samples decreasing with decrease in coal content. The values for the higher condensed PAHs showed that the highest desorption enthalpies were from the samples with the largest amount of coal-derived particles. Elevated desorption enthalpies indicated a strong bonding between PAHs and geosorbents. Moreover, with the application of ASE this study was able to conclude that the PAHs in the samples were preferentially adsorbed to carbonaceous materials with high surface areas. PMID:19524343

  13. Process for removing halogenated aliphatic and aromatic compounds from petroleum products

    DOEpatents

    Googin, John M.; Napier, John M.; Travaglini, Michael A.

    1983-01-01

    A process for removing halogenated aliphatic and aromatic compounds, e.g., polychlorinated biphenyls, from petroleum products by solvent extraction. The halogenated aliphatic and aromatic compounds are extracted from a petroleum product into a polar solvent by contacting the petroleum product with the polar solvent. The polar solvent is characterized by a high solubility for the extracted halogenated aliphatic and aromatic compounds, a low solubility for the petroleum product and considerable solvent power for polyhydroxy compound. The preferred polar solvent is dimethylformamide. A miscible compound, such as, water or a polyhydroxy compound, is added to the polar extraction solvent to increase the polarity of the polar extraction solvent. The halogenated aliphatic and aromatic compounds are extracted from the highly-polarized mixture of water or polyhydroxy compound and polar extraction solvent into a low polar or nonpolar solvent by contacting the water or polyhydroxy compound-polar solvent mixture with the low polar or nonpolar solvent. The halogenated aliphatic and aromatic compounds and the low polar or nonpolar solvent are separated by physical means, e.g., vacuum evaporation. The polar and nonpolar solvents are recovered from recycling. The process can easily be designed for continuous operation. Advantages of the process include that the polar solvent and a major portion of the nonpolar solvent can be recycled, the petroleum products are reclaimable and the cost for disposing of waste containing polychlorinated biphenyls is significantly reduced.

  14. Process for removing halogenated aliphatic and aromatic compounds from petroleum products

    DOEpatents

    Googin, J.M.; Napier, J.M.; Travaglini, M.A.

    1983-09-20

    A process is described for removing halogenated aliphatic and aromatic compounds, e.g., polychlorinated biphenyls, from petroleum products by solvent extraction. The halogenated aliphatic and aromatic compounds are extracted from a petroleum product into a polar solvent by contacting the petroleum product with the polar solvent. The polar solvent is characterized by a high solubility for the extracted halogenated aliphatic and aromatic compounds, a low solubility for the petroleum product and considerable solvent power for polyhydroxy compound. The preferred polar solvent is dimethylformamide. A miscible compound, such as, water or a polyhydroxy compound, is added to the polar extraction solvent to increase the polarity of the polar extraction solvent. The halogenated aliphatic and aromatic compounds are extracted from the highly-polarized mixture of water or polyhydroxy compound and polar extraction solvent into a low polar or nonpolar solvent by contacting the water or polyhydroxy compound-polar solvent mixture with the low polar or nonpolar solvent. The halogenated aliphatic and aromatic compounds and the low polar or nonpolar solvent are separated by physical means, e.g., vacuum evaporation. The polar and nonpolar solvents are recovered from recycling. The process can easily be designed for continuous operation. Advantages of the process include that the polar solvent and a major portion of the nonpolar solvent can be recycled, the petroleum products are reclaimable and the cost for disposing of waste containing polychlorinated biphenyls is significantly reduced. 1 fig.

  15. Green chemicals: Searching for cleaner solvents

    SciTech Connect

    Lucas, A.

    1994-10-05

    While increased pressure from EPA has solvents producers scrambling to find greener alternatives, many say the cost effectiveness and performance characteristics of traditional technologies are such that they will not disappear quickly. Though a variety of alternative {open_quotes}green{close_quotes} solvents have been developed and commercialized, better means of solvent recovery have also come along, ensuring continued use of many organic solvents. The 1990 Clean Air Act (CAA), designed to eliminate volatile organic compounds (VOCs), ozone depleters, and other hazardous air pollutants (HAPs), has put limits on many organic solvents. Those most under fire are chlorinated solvents, such as methylene chloride, 1,1,1 trichloroethylene (methyl chloroform), and chlorofluorocarbon (CFC)-113. Producers have been developing a variety of lower VOC solvents to replace those being phased out or regulated. Among those likely to experience most growth are aliphatic hydrocarbons to replace chlorinated solvents in cleaning applications. Growth is also expected for alcohols, esters, and glycol ethers for other end-use applications.

  16. Pyrostegia venusta heptane extract containing saturated aliphatic hydrocarbons induces apoptosis on B16F10-Nex2 melanoma cells and displays antitumor activity in vivo

    PubMed Central

    Figueiredo, Carlos R.; Matsuo, Alisson L.; Pereira, Felipe V.; Rabaça, Aline N.; Farias, Camyla F.; Girola, Nátalia; Massaoka, Mariana H.; Azevedo, Ricardo A.; Scutti, Jorge A.B.; Arruda, Denise C.; Silva, Luciana P.; Rodrigues, Elaine G.; Lago, João Henrique G.; Travassos, Luiz R.; Silva, Regildo M.G.

    2014-01-01

    Background: Pyrostegia venusta (Ker. Gawl.) Miers (Bignoniacea) is a medicinal plant from the Brazilian Cerrado used to treat leucoderma and common diseases of the respiratory system. Objective: To investigate the antitumor activity of P.venusta extracts against melanoma. Materials and Methods: The cytotoxic activity and tumor induced cell death of heptane extract (HE) from P. venusta flowers was evaluated against murine melanoma B16F10-Nex2 cells in vitro and in a syngeneic model in vivo. Results: We found that HE induced apoptosis in melanoma cells by disruption of the mitochondrial membrane potential, induction of reactive oxygen species and late apoptosis evidenced by plasma membrane blebbing, cell shrinkage, chromatin condensation and DNA fragmentation, exposure of phosphatidylserine on the cell surface and activation of caspase-2,-3,-8,-9. HE was also protective against singeneyc subcutaneous melanoma HE compounds were also able to induce cell cycle arrest at G2/M phases on tumor cells. On fractionation of HE in silica gel we isolated a cytotoxic fraction that contained a mixture of saturated hydrocarbons identified by 1H NMR and GC-MS analyses. Predominant species were octacosane (C28H58-36%) and triacontane (C30H62-13%), which individually showed significant cytotoxic activity against murine melanoma B16F10-Nex2 cells in vitro and a very promising antitumor protection against subcutaneous melanoma in vivo. Conclusion: The results suggest that the components of the heptane extract, mainly octasane and triacontane, which showed antitumor properties in experimental melanoma upon regional administration, might also be therapeutic in human cancer, such as in the mostly epidermal and slowly invasive melanomas, such as acral lentiginous melanoma, as an adjuvant treatment to surgical excision. PMID:24991116

  17. Effect of in vivo jet fuel exposure on subsequent in vitro dermal absorption of individual aromatic and aliphatic hydrocarbon fuel constituents.

    PubMed

    Muhammad, F; Monteiro-Riviere, N A; Baynes, R E; Riviere, J E

    2005-05-14

    The percutaneous absorption of topically applied jet fuel hydrocarbons (HC) through skin previously exposed to jet fuel has not been investigated, although this exposure scenario is the occupational norm. Pigs were exposed to JP-8 jet fuel-soaked cotton fabrics for 1 and 4 d with repeated daily exposures. Preexposed and unexposed skin was then dermatomed and placed in flow-through in vitro diffusion cells. Five cells with exposed skin and four cells with unexposed skin were dosed with a mixture of 14 different HC consisting of nonane, decane, undecane, dodecane, tridecane, tetradecane, pentadecane, hexadecane, ethyl benzene, o-xylene, trimethyl benzene (TMB), cyclohexyl benzene (CHB), naphthalene, and dimethyl naphthalene (DMN) in water + ethanol (50:50) as diluent. Another five cells containing only JP-8-exposed skin were dosed solely with diluent in order to determine the skin retention of jet fuel HC. The absorption parameters of flux, diffusivity, and permeability were calculated for the studied HC. The data indicated that there was a two-fold and four-fold increase in absorption of specific aromatic HC like ethyl benzene, o-xylene, and TMB through 1- and 4-dJP-8 preexposed skin, respectively. Similarly, dodecane and tridecane were absorbed more in 4-d than 1-dJP-8 preexposed skin experiments. The absorption of naphthalene and DMN was 1.5 times greater than the controls in both 1- and 4-d preexposures. CHB, naphthalene, and DMN had significant persistent skin retention in 4-d preexposures as compared to 1-d exposures that might leave skin capable of further absorption several days postexposure. The possible mechanism of an increase in HC absorption in fuel preexposed skin may be via lipid extraction from the stratum corneum as indicated by Fourier transform infrared (FTIR) spectroscopy. This study suggests that the preexposure of skin to jet fuel enhances the subsequent in vitro percutaneous absorption of HC, so single-dose absorption data for jet fuel HC from

  18. Monitoring the effect of poplar trees on petroleum-hydrocarbon and chlorinated-solvent contaminated ground water

    USGS Publications Warehouse

    Landmeyer, J.E.

    2001-01-01

    At contaminated groundwater sites, poplar trees can be used to affect groundwater levels, flow directions, and ultimately total groundwater and contaminant flux to areas downgradient of the trees. The magnitude of the hydrologic changes can be monitored using fundamental concepts of groundwater hydrology, in addition to plant physiology-based approaches, and can be viewed as being almost independent of the contaminant released. The affect of poplar trees on the fate of groundwater contaminants, however, is contaminant dependent. Some petroleum hydrocarbons or chlorinated solvents may be mineralized or transformed to innocuous compounds by rhizospheric bacteria associated with the tree roots, mineralized or transformed by plant tissues in the transpiration stream or leaves after uptake, or passively volatilized and rapidly dispersed or oxidized in the atmosphere. These processes also can be monitored using a combination of physiological- or geochemical-based field or laboratory approaches. When combined, such hydrologic and contaminant monitoring approaches can result in a more accurate assessment of the use of poplar trees to meet regulatory goals at contaminated groundwater sites, verify that these goals continue to be met in the future, and ultimately lead to a consensus on how the performance of plant-based remedial strategies (phytoremediation) is to be assessed.

  19. Photolysis of aryl chlorides with aliphatic amines

    SciTech Connect

    Bunce, N.J.

    1982-05-07

    Kinetic arguments show that the aliphatic amine assisted photodechlorinations of chlorides of the benzene, naphthalene, and biphenyl series take place mainly from the triplet excited state. Deuterium labeling studies have been used to determine the origin of the hydrogen atom which replaces chlorine when 4-chlorobiphenyl is photoreduced. Three pathways are inferred: hydrogen abstraction from the solvent and protonation both within the exciplex (or radical ion pair) and by external proton donors.

  20. Study of hydrocarbon miscible solvent slug injection process for improved recovery of heavy oil from Schrader Bluff Pool, Milne Point Unit, Alaska. Final report

    SciTech Connect

    1995-11-01

    The National Energy Strategy Plan (NES) has called for 900,000 barrels/day production of heavy oil in the mid-1990s to meet our national needs. To achieve this goal, it is important that the Alaskan heavy oil fields be brought to production. Alaska has more than 25 billion barrels of heavy oil deposits. Conoco, and now BP Exploration have been producing from Schrader Bluff Pool, which is part of the super heavy oil field known as West Sak Field. Schrader Bluff reservoir, located in the Milne Point Unit, North Slope of Alaska, is estimated to contain up to 1.5 billion barrels of (14 to 21{degrees}API) oil in place. The field is currently under production by primary depletion; however, the primary recovery will be much smaller than expected. Hence, waterflooding will be implemented earlier than anticipated. The eventual use of enhanced oil recovery (EOR) techniques, such as hydrocarbon miscible solvent slug injection process, is vital for recovery of additional oil from this reservoir. The purpose of this research project was to determine the nature of miscible solvent slug which would be commercially feasible, to evaluate the performance of the hydrocarbon miscible solvent slug process, and to assess the feasibility of this process for improved recovery of heavy oil from Schrader Bluff reservoir. The laboratory experimental work includes: slim tube displacement experiments and coreflood experiments. The components of solvent slug includes only those which are available on the North Slope of Alaska.

  1. Model studies for evaluating the acute neurobehavioral effects of complex hydrocarbon solvents I. Validation of methods with ethanol.

    PubMed

    McKee, R H; Lammers, J H C M; Hoogendijk, E M G; Emmen, H H; Muijser, H; Barsotti, D A; Owen, D E; Kulig, B M

    2006-12-01

    As a preliminary step to evaluating the acute neurobehavioral effects of hydrocarbon solvents and to establish a working model for extrapolating animal test data to humans, joint neurobehavioral/toxicokinetic studies were conducted which involved administering ethanol to rats and volunteers. The specific objectives of the present studies were to evaluate the acute central nervous system (CNS) effects of ethanol in rats and humans and to assess relationships between internal levels of exposure and behavioral effects. A more general objective was to validate a battery of neurobehavioral tests that could be used to carry out comparative studies in both species. Accordingly, a range of tests including standardized observational measures, spontaneous motor activity assessments and learned visual discrimination performance was utilized in rat studies to evaluate acute CNS effects. Groups of rats were given ethanol at levels of approximately 0.5, 1.0 or 2.0g/kg, with blood level measurements to verify internal doses. In a volunteer study, 12 healthy male subjects were given 0.65g/kg ethanol, a level approximating the limit for motor vehicle operation in The Netherlands, and neurobehavioral effects were measured prior to and 1 and 3h after ethanol administration, with a computerized neurobehavioral test battery. Blood and air measurements were made to quantify internal doses. Results of the behavioral tests in rats provided evidence of ethanol-induced changes in neuromuscular, sensori-motor, and activity domains. There were also significant changes in visual discrimination, particularly in the areas of general measures of responding and psychomotor speed. In humans there were small but statistically significant effects on learning and memory, psychomotor skills and attention. However, the effects were subtle and not all parameters within given domains were affected. These studies demonstrated a qualitative similarity in response between rats and humans. PMID:16831461

  2. The potential of solvent-minimized extraction methods in the determination of polycyclic aromatic hydrocarbons in fish oils.

    PubMed

    Yebra-Pimentel, Iria; Martínez-Carballo, Elena; Regueiro, Jorge; Simal-Gándara, Jesús

    2013-08-15

    Fish oil has been identified as one of the most important contributors to the level of Persistent Organic Pollutants (POPs) in feed products. The determination of polycyclic aromatic hydrocarbons (PAHs) in fish oils is complicated due to the fat matrix, which affects both extraction efficiency and analytical quality. This article reviews and addresses two of the most relevant analytical methods for determining 11 mutagenic and carcinogenic PAHs, as well as two EPA indicator PAHs in fish oils. We discuss and critically evaluate two different extraction procedures, such as ultrasound-assisted solvent extraction (USAE) and ultrasound-assisted emulsification-microextraction (USAEME). Clean-up of extracts was performed by solid-phase extraction using C18 and glass columns containing silica gel and florisil for USAE or only C18 for USAEME. Detection of the selected PAHs was carried out by high-performance liquid chromatography coupled with fluorescence detection for determination. Optimization of the variables affecting extraction by the selected extraction techniques was conducted and recoveries ranged from 70% to 100% by USAE and from 70% to 108% by USAEME with estimated quantification limits between 0.020 and 2.6 μg/kg were achieved. Moreover, the applicability of the selected methods was evaluated by the analysis of real samples. To our knowledge, this is the first time that USAEME has been applied to the determination of PAHs in food matrices, such as oil fish samples. The methods proposed were applied to the determination of the target PAHs in fish samples from different countries, and it was found that the low PAH contamination of the selected fish oils could mainly occur by atmospheric sources. PMID:23561207

  3. ALIPHATIC HALOGENATED HYDROCARBONS PRODUCE VOLATILE 'SALMONELLA' MUTAGENS

    EPA Science Inventory

    Production of volatile mutagenic metabolites from 5 halogenated promutagens was examined by a simple modification of the conventional Salmonella/microsome mutagenicity assay. This method incorporates the taping together of 2 agar plates face to face during the initial portion of ...

  4. J-aggregation, its impact on excited state dynamics and unique solvent effects on macroscopic assembly of a core-substituted naphthalenediimide.

    PubMed

    Kar, Haridas; Gehrig, Dominik W; Laquai, Frédéric; Ghosh, Suhrit

    2015-04-21

    Herein we reveal a straightforward supramolecular design for the H-bonding driven J-aggregation of an amine-substituted cNDI in aliphatic hydrocarbons. Transient absorption spectroscopy reveals sub-ps intramolecular electron transfer in isolated NDI molecules in a THF solution followed by a fast recombination process, while a remarkable extension of the excited state lifetime by more than one order of magnitude occurred in methylcyclohexane likely owing to an increased charge-separation as a result of better delocalization of the charge-separated states in J-aggregates. We also describe unique solvent-effects on the macroscopic structure and morphology. While J-aggregation with similar photophysical characteristics was noticed in all the tested aliphatic hydrocarbons, the morphology strongly depends on the "structure" of the solvents. In linear hydrocarbons (n-hexane, n-octane, n-decane or n-dodecane), formation of an entangled fibrillar network leads to macroscopic gelation while in cyclic hydrocarbons (methylcyclohexane or cyclohexane) although having a similar polarity, the cNDI exhibits nanoscale spherical particles. These unprecedented solvent effects were rationalized by establishing structure-dependent specific interactions of the solvent molecules with the cNDI which may serve as a general guideline for solvent-induced morphology-control of structurally related self-assembled materials. PMID:25805563

  5. Solvent extraction of diatomite

    SciTech Connect

    Williams, W.

    1984-07-24

    There is provided a method of extracting hydrocarbons from a diatomite ore. The particle size of the ore is first reduced to form a processed ore. The processed ore is then mixed with a substantially irregular granular material to form an unstratified ore mixture having increased permeability to an extracting solvent. The unstratified ore mixture is then permeated with an extracting solvent to obtain a hydrocarbon-solvent stream from which hydrocarbons are subsequently separated. The irregular granular material may be sand.

  6. Analysis of solvent dyes in refined petroleum products by electrospray ionization mass spectrometry

    USGS Publications Warehouse

    Rostad, C.E.

    2010-01-01

    Solvent dyes are used to color refined petroleum products to enable differentiation between gasoline, diesel, and jet fuels. Analysis for these dyes in the hydrocarbon product is difficult due to their very low concentrations in such a complex matrix. Flow injection analysis/electrospray ionization/mass spectrometry in both negative and positive mode was used to optimize ionization of ten typical solvent dyes. Samples of hydrocarbon product were analyzed under similar conditions. Positive electrospray ionization produced very complex spectra, which were not suitably specific for targeting only the dyes. Negative electrospray ionization produced simple spectra because aliphatic and aromatic moieties were not ionized. This enabled screening for a target dye in samples of hydrocarbon product from a spill.

  7. Process for removing halogenated aliphatic and aromatic compounds from petroleum products. [Polychlorinated biphenyls; methylene chloride; perchloroethylene; trichlorofluoroethane; trichloroethylene; chlorobenzene

    DOEpatents

    Googin, J.M.; Napier, J.M.; Travaglini, M.A.

    1982-03-31

    A process for removing halogenated aliphatic and aromatic compounds, e.g., polychlorinated biphenyls, from petroleum products by solvent extraction. The halogenated aliphatic and aromatic compounds are extracted from a petroleum product into a polar solvent by contracting the petroleum product with the polar solvent. The polar solvent is characterized by a high solubility for the extracted halogenated aliphatic and aromatic compounds, a low solubility for the petroleum product and considerable solvent power for polyhydroxy compound. The preferred polar solvent is dimethylformamide. A miscible polyhydroxy compound, such as, water, is added to the polar extraction solvent to increase the polarity of the polar extraction solvent. The halogenated aliphatic and aromatic compounds are extracted from the highly-polarized mixture of polyhydroxy compound and polar extraction solvent into a low polar or nonpolar solvent by contacting the polyhydroxy compound-polar solvent mixture with the low polar or nonpolar solvent. The halogenated aliphatic and aromatic compounds in the low polar or nonpolar solvent by physical means, e.g., vacuum evaporation. The polar and nonpolar solvents are recovered for recycling. The process can easily be designed for continuous operation. Advantages of the process include that the polar solvent and a major portion of the nonpolar solvent can be recycled, the petroleum products are reclaimable and the cost for disposing of waste containing polychlorinated biphenyls is significantly reduced. 2 tables.

  8. HPLC/APCI Mass Spectrometry of Saturated and Unsaturated Hydrocarbons by Using Hydrocarbon Solvents as the APCI Reagent and HPLC Mobile Phase

    NASA Astrophysics Data System (ADS)

    Gao, Jinshan; Owen, Benjamin C.; Borton, David J.; Jin, Zhicheng; Kenttämaa, Hilkka I.

    2012-05-01

    Saturated and unsaturated, linear, branched, and cyclic hydrocarbons, as well as polyaromatic and heteroaromatic hydrocarbons, were successfully ionized by atmospheric pressure chemical ionization (APCI) using small hydrocarbons as reagents in a linear quadrupole ion trap (LQIT) mass spectrometer. Pentane was proved to be the best reagent among the hydrocarbon reagents studied. This ionization method generated different types of abundant ions (i.e., [M + H]+, M+•, [M - H]+ and [M - 2H]+ •), with little or no fragmentation. The radical cations can be differentiated from the even-electron ions by using dimethyl disulfide, thus facilitating molecular weight (MW) determination. While some steroids and lignin monomer model compounds, such as androsterone and 4-hydroxy-3-methoxybenzaldehyde, also formed abundant M+• and [M + H]+ ions, this was not true for all of them. Analysis of two known mixtures as well as a base oil sample demonstrated that each component of the known mixtures could be observed and that a correct MW distribution was obtained for the base oil. The feasibility of using this ionization method on the chromatographic time scale was demonstrated by using high-performance liquid chromatography (HPLC) with hexane as the mobile phase (and APCI reagent) to separate an artificial mixture prior to mass spectrometric analysis.

  9. Application of a magnesium/co-solvent system for the degradation of polycyclic aromatic hydrocarbons and their oxygenated derivatives in a spiked soil.

    PubMed

    Elie, Marc R; Williamson, Robert E; Clausen, Christian A; Yestrebsky, Cherie L

    2014-12-01

    This study evaluates the capability, efficacy and practicality of a combined approach based on solvent extraction and chemical reduction to simultaneously degrade polycyclic aromatic hydrocarbons (PAHs) and their oxygenated derivatives (OPAHs) in spiked soil. The spiked soil was washed using a composite organic solvent consisting of ethanol and ethyl lactate (1:1, v/v) and then degradation of the extracted contaminants using zero-valent magnesium. The extraction conditions were optimized at 25 °C with solvent-soil ratio of 2:1 (v/w) and the ensuing degradation efficiency ranged from 79% to 88% for the OPAHs, and 66% to 87% for the PAHs after 24 h of reaction at pH of 6.1. The reductive degradation of the spiked contaminants followed pseudo-first-order kinetics; however, comparing the kinetic results of this study to soil-free studies, the degradation rates are significantly reduced. It can be inferred that extracted organic or inorganic components from the soil medium hinder the degradation process, possibly by reducing the reactivity of the activated metal. Furthermore, to our understanding, this study is the first report on the simultaneous degradation of these priority pollutants and their oxygenated derivatives. The experimental results encourage the application of this magnesium/co-solvent system for future pilot-scale remediation studies. PMID:25461950

  10. Production of Alkaline Protease by Solvent-Tolerant Alkaliphilic Bacillus circulans MTCC 7942 Isolated from Hydrocarbon Contaminated Habitat: Process Parameters Optimization.

    PubMed

    Patil, Ulhas; Chaudhari, Ambalal

    2013-01-01

    In the present investigation, a newly isolated organic solvent-tolerant and alkaliphilic bacterial strain was reported from a hydrocarbon (gasoline and diesel) contaminated soil collected from the petrol station, Shirpur (India). The strain was identified as Bacillus circulans MTCC 7942, based on phenotype, biochemical, and phylogenetic analysis of 16S rRNA gene sequence. The capability of Bacillus circulans to secrete an extracellular, thermostable, alkaline protease and grow in the presence of organic solvents was explored. Bacillus circulans produced maximum alkaline protease (412 U/mL) in optimized medium (g/L): soybean meal, 15; starch, 10; KH2PO4, 1; MgSO4·7H2O, 0.05; CaCl2, 1; Na2CO3, 8; pH 10.0 at 37°C and 100 rpm. The competence of strain to grow in various organic solvents-n-octane, dodecane, n-decane, N,N-dimethylformamide, n-hexane, and dimethyl sulfoxide, establishes its potential as solvent-stable protease source for the possible applications in nonaqueous reactions and fine chemical synthesis. PMID:25937965

  11. Study of hydrocarbon miscible solvent slug injection process for improved recovery of heavy oil from Schrader Bluff Pool, Milne Point Unit, Alaska. Annual report, January 1, 1994--December 31, 1994

    SciTech Connect

    Sharma, G.D.

    1995-07-01

    Alaska is the second largest oil producing state in the nation and currently contributes nearly 24% of the nations oil production. It is imperative that Alaskan heavy oil fields be brought into production. Schrader Bluff reservoir, located in the Milne Point Unit, which is part of the heavy oil field known as West Sak is estimated to contain 1.5 billion barrels of (14 to 21 degree API) oil-in-place. The field is currently under production by primary depletion. The eventual implementation of enhanced oil recovery (EOR) techniques will be vital for the recovery of additional oil from this reservoir. The availability of hydrocarbon gases (solvents) on the Alaska North Slope make the hydrocarbon miscible solvent injection process an important consideration for the EOR project in Schrader Bluff reservoir. Since Schrader Bluff oil is heavy and viscous, a water-alternating-gas (WAG) type of process for oil recovery is appropriate since such a process tends to derive synergetic benefits from both water injection (which provides mobility control and improvement in sweep efficiency) and miscible gas injection (which provides improved displacement efficiency). A miscible solvent slug injection process rather than continuous solvent injection is considered appropriate. Slim tube displacement studies, PVT data and asphaltene precipitation studies are needed for Schrader bluff heavy oil to define possible hydrocarbon solvent suitable for miscible solvent slug displacement process. Coreflood experiments are also needed to determine the effect of solvent slug size, WAG ratio and solvent composition on the recovery and solvent breakthrough. A compositional reservoir simulation study will be conducted later to evaluate the complete performance of the hydrocarbon solvent slug process and to assess the feasibility of this process for improving recovery of heavy oil from Schrader Bluff reservoir.

  12. Rapid determination of trace polycyclic aromatic hydrocarbons in particulate matter using accelerated solvent extraction followed by ultra high performance liquid chromatography with fluorescence detection.

    PubMed

    Xu, Tianci

    2016-05-01

    A method has been developed for the trace analysis of polycyclic aromatic hydrocarbons, which are known as persistent organic pollutants and ubiquitous constituents of fine particulate matter that causes growing airborne pollution. The method, which was especially for samples of airborne particulate matter less than 2.5 μm in diameter, utilized accelerated solvent extraction and ultra high performance liquid chromatography with fluorescence detector. Four principal parameters of accelerated solvent extraction were optimized to obtain maximum extraction efficiency. Using the established synergetic programs of gradient elution and fluorescence wavelength switching, a rapid separation was achieved in 6.56 min with good linearity for 15 polycyclic aromatic hydrocarbons (coefficient of determination above 0.999). The limits of detection ranged from 0.833 to 10.0 pg/m(3) . The precision of the method expressed as inter-day relative standard deviation ranged from 0.2 to 1%, which was calculated from nine repetitive measurements of 8.00 μg/L analytes. Average spiked recoveries ranged from 71.6 to 97.7%, with the exception of naphthalene. The rapid, sensitive, and accurate method can meet the pressing needs of health risk assessment and increasingly heavy daily tasks of air quality monitoring. PMID:26991966

  13. Project Summary. IN-SITU AQUIFER RESTORATION OF CHLORINATED ALIPHATICS BY METHANOTROPHIC BACTERIA

    EPA Science Inventory

    This project evaluated the potential of an innovative approach to aquifer restoration: enhanced in-situ biotransformation of chlorinated aliphatic solvents by a bacterial community grown on methane under aerobic conditions. The target chlorinated compounds were trichloroethene (...

  14. Solvent-free aerobic oxidation of hydrocarbons and alcohols with Pd@N-doped carbon from glucose.

    PubMed

    Zhang, Pengfei; Gong, Yutong; Li, Haoran; Chen, Zhirong; Wang, Yong

    2013-01-01

    The development of efficient systems for selective aerobic oxidation of hydrocarbons and alcohols to produce more functional compounds (aldehydes, ketones, acids or esters) with atmospheric air or molecular oxygen is a grand challenge for the chemical industry. Here we report the synthesis of palladium nanoparticles supported on novel nanoporous nitrogen-doped carbon, and their impressive performance in the controlled oxidation of hydrocarbons and alcohols with air. In terms of catalytic activity, these catalysts afford much higher turnover frequencies (up to 863 turnovers per hour for hydrocarbon oxidation and up to ~210,000 turnovers per hour for alcohol oxidation) than most reported palladium catalysts under the same reaction conditions. This work provides great potential for the application of ambient air and recyclable palladium catalysts in fine-chemical production with high activity. PMID:23481401

  15. Production of Alkaline Protease by Solvent-Tolerant Alkaliphilic Bacillus circulans MTCC 7942 Isolated from Hydrocarbon Contaminated Habitat: Process Parameters Optimization

    PubMed Central

    Patil, Ulhas; Chaudhari, Ambalal

    2013-01-01

    In the present investigation, a newly isolated organic solvent-tolerant and alkaliphilic bacterial strain was reported from a hydrocarbon (gasoline and diesel) contaminated soil collected from the petrol station, Shirpur (India). The strain was identified as Bacillus circulans MTCC 7942, based on phenotype, biochemical, and phylogenetic analysis of 16S rRNA gene sequence. The capability of Bacillus circulans to secrete an extracellular, thermostable, alkaline protease and grow in the presence of organic solvents was explored. Bacillus circulans produced maximum alkaline protease (412 U/mL) in optimized medium (g/L): soybean meal, 15; starch, 10; KH2PO4, 1; MgSO4·7H2O, 0.05; CaCl2, 1; Na2CO3, 8; pH 10.0 at 37°C and 100 rpm. The competence of strain to grow in various organic solvents—n-octane, dodecane, n-decane, N,N-dimethylformamide, n-hexane, and dimethyl sulfoxide, establishes its potential as solvent-stable protease source for the possible applications in nonaqueous reactions and fine chemical synthesis. PMID:25937965

  16. Inter-rater reliability of assessed prenatal maternal occupational exposures to solvents, polycyclic aromatic hydrocarbons, and heavy metals.

    PubMed

    Rocheleau, Carissa M; Lawson, Christina C; Waters, Martha A; Hein, Misty J; Stewart, Patricia A; Correa, Adolfo; Echeverria, Diana; Reefhuis, Jennita

    2011-12-01

    Because direct measurements of past occupational exposures are rarely available in population-based case-control studies, exposure assessment of job histories by multiple expert raters is frequently used; however, the subjective nature of this method makes measuring reliability an important quality control step. We evaluated inter-rater reliability of 7729 retrospective jobs reported in the National Birth Defects Prevention Study. Jobs were classified as exposed, unexposed, or exposure unknown by two independent industrial hygienists; exposed jobs were further evaluated for intensity, frequency, and routes. Exposure prevalence ranged from 0.1-9.8%. Inter-rater reliability for exposure (yes/no), assessed by kappa coefficients, was fair to good for cadmium (κ = 0.46), chlorinated solvents (κ = 0.59), cobalt (κ = 0.54), glycol ethers (κ = 0.50), nickel compounds (κ = 0.65), oil mists (κ = 0.63), and Stoddard Solvent (κ = 0.55); PAHs (κ = 0.24) and elemental nickel (κ = 0.37) had poor agreement. After a consensus conference resolved disagreements, an additional 4962 jobs were evaluated. Inter-rater reliability improved or stayed the same for cadmium (κ = 0.51), chlorinated solvents (κ = 0.81), oil mists (κ = 0.63), PAHs (κ = 0.52), and Stoddard solvent (κ = 0.92) in the second job set. Inter-rater reliability varied by exposure agent and prevalence, demonstrating the importance of measuring reliability in studies using a multiple expert rater method of exposure assessment. PMID:22074298

  17. Preferences in removal of aliphatic and aromatic gasoline components by biofiltration under varied loading.

    PubMed

    Halecky, Martin; Paca, Jan; Kozliak, Evguenii I

    2012-01-01

    Removal of gasoline vapors from waste air was investigated in a bench-scale perlite biofilter for three aromatic-to-aliphatic mass ratios (62/38, 92/8 and 44/56) under different loads, varied by changing both the substrate inlet concentration and air flow rate. The measurement of concentration profiles along the bed height allowed for an assessment of interactions between the aromatic and aliphatic fractions of gasoline. Variations in both the inlet concentrations and empty bed residence time significantly influenced the removal of aliphatic gasoline components. Except for the lowest organic loads, the whole biofilter bed was required for achieving an acceptable removal efficiency of aliphatic hydrocarbons. The presence of large amounts of aromatics negatively impacted the removal of aliphatics. By contrast, the aromatic gasoline components were near-completely removed from any mixtures; the bulk of them were degraded in the first (out of three) biofilter section, even at high concentrations of aliphatic hydrocarbons. The observed effect was shown to be due to competitive interactions of aliphatic and aromatic components, which is consistent with the biological steps being rate limiting. Mass transfer, particularly for aliphatic components due to their high Henry's law constants, was shown to be rate-limiting under extreme scenarios, such as low loading rates and EBRT. PMID:22486669

  18. Effect of organic solvents on nervous cell membrane as measured by changes in the (Ca2+/Mg2+) ATPase activity and fluidity of synaptosomal membrane.

    PubMed

    Edelfors, S; Ravn-Jonsen, A

    1992-03-01

    The effect of various solvents on the central nervous system was studied by using rat brain synaptosomal membranes as an in vitro model. The activity of (Ca2+/Mg2+) ATPase and the membrane fluidity was determined. The alteration of the ATPase activity depended on the physio-chemical characteristics of the solvent in question. Incubation with aliphatic alkanes caused a stimulation of the ATPase activity whereas mixed hydrocarbons as kerosene, white spirit and gasoline inhibited the enzyme. Incubation with chlorinated hydrocarbons caused a biphasic response dependent on the concentration. Oxygen-containing hydrocarbons exhibited various effects as found after incubation with hydrocarbons. The different effects of the solvents on the ATPase activity suggest that the lipophilicity of the solvents is one of more parameters affecting the membrane. Furthermore, the biphasic response following the incubation with chlorinated hydrocarbons indicates that more mechanisms are involved in the enzyme effect. The membrane fluidity is increased with higher concentrations of the solvents. From the results it is concluded that the ATPase activity depends not only on the membrane fluidity and volume, but also on the hydrophilic vicinity of the enzyme molecule. PMID:1533717

  19. Study of hydrocarbon miscible solvent slug injection process for improved recovery of heavy oil from Schrader Bluff Pool, Milne Point Unit, Alaska. Annual report, December 1, 1992--December 31, 1993

    SciTech Connect

    Sharma, G.D.

    1994-01-01

    The shallow Cretaceous sands of the Schrader Bluff Reservoir occur between depths of 4,000 and 4,800 feet below surface and are estimated to contain up to 1.5 billion barrels of oil in place. The field is currently under production by primary depletion. Initial production indicated that primary recovery will fall short of earlier estimates and waterflooding will have to be employed much earlier than expected. A large portion of the oil-in-place thus would still be left behind in this reservoir after primary and secondary recovery methods have been applied. Enhanced oil recovery (EOR) techniques will be needed to recover the additional portion of remaining oil in this huge reservoir and to add significant additional reserves. Slim tube displacement studies, PVT data and asphaltene precipitation studies are needed for Schrader Bluff heavy oil to define possible hydrocarbon solvent suitable for miscible solvent slug displacement process. Such studies are essential because the API gravity of the crude in Schrader Bluff reservoir varies significantly from well to well. Coreflood experiments are also needed to determine effect of solvent slug size, WAG ratio and solvent composition on the oil recovery and solvent breakthrough. A compositional reservoir simulation study will be conducted later to evaluate the complete performance of the hydrocarbon solvent slug process and to assess the feasibility of this process for improving recovery of heavy oil from Schrader Bluff reservoir. This report contains the following: reservoir description; slim tube displacement studies; and coreflood experiments.

  20. Extraction of S- and N-Compounds from the Mixture of Hydrocarbons by Ionic Liquids as Selective Solvents

    PubMed Central

    Gabrić, Beata; Sander, Aleksandra; Cvjetko Bubalo, Marina; Macut, Dejan

    2013-01-01

    Liquid-liquid extraction is an alternative method that can be used for desulfurization and denitrification of gasoline and diesel fuels. Recent approaches employ different ionic liquids as selective solvents, due to their general immiscibility with gasoline and diesel, negligible vapor pressure, and high selectivity to sulfur- and nitrogen-containing compounds. For that reason, five imidazolium-based ionic liquids and one pyridinium-based ionic liquid were selected for extraction of thiophene, dibenzothiophene, and pyridine from two model solutions. The influences of hydrodynamic conditions, mass ratio, and number of stages were investigated. Increasing the mass ratio of ionic liquid/model fuel and multistage extraction promotes the desulfurization and denitrification abilities of the examined ionic liquids. All selected ionic liquids can be reused and regenerated by means of vacuum evaporation. PMID:23843736

  1. Biodegradation by an arthrobacter species of hydrocarbons partitioned into an organic solvent. (Reannouncement with new availability information)

    SciTech Connect

    Efroymson, R.A.; Alexander, M.

    1991-05-01

    An Arthrobacter strain mineralized naphthalene and n-hexadecane dissolved in 2,2,4,4,6,8,8-heptamethylnonane. The extent of mineralization increased with greater volumes of solvent. Measurements under aseptic conditions of the partitioning of naphthalene into the aqueous phase from the solid phase or from heptamethylnonane showed that the rates were rapid and did not limit mineralization. The rate of mineralization of hexadecane was rapid, although partitioning of the compound into aqueous solution was not detected. The Arthrobacter sp. grown in media with or without heptamethylnonane did not excrete products that increased the aqueous solubility of naphthalene and hexadecane. Measurements of the number of cells in the aqueous phase showed that the Arthrobacter sp. attached to the heptamethylnonane-water interface, but attachment was evident even without a substrate in the heptamethylnonane.

  2. Extraction of S- and N-compounds from the mixture of hydrocarbons by ionic liquids as selective solvents.

    PubMed

    Gabrić, Beata; Sander, Aleksandra; Cvjetko Bubalo, Marina; Macut, Dejan

    2013-01-01

    Liquid-liquid extraction is an alternative method that can be used for desulfurization and denitrification of gasoline and diesel fuels. Recent approaches employ different ionic liquids as selective solvents, due to their general immiscibility with gasoline and diesel, negligible vapor pressure, and high selectivity to sulfur- and nitrogen-containing compounds. For that reason, five imidazolium-based ionic liquids and one pyridinium-based ionic liquid were selected for extraction of thiophene, dibenzothiophene, and pyridine from two model solutions. The influences of hydrodynamic conditions, mass ratio, and number of stages were investigated. Increasing the mass ratio of ionic liquid/model fuel and multistage extraction promotes the desulfurization and denitrification abilities of the examined ionic liquids. All selected ionic liquids can be reused and regenerated by means of vacuum evaporation. PMID:23843736

  3. Solvent refining process

    SciTech Connect

    Mead, T.C.; Sequeira, A.J.; Smith, B.F.

    1981-10-13

    An improved process is described for solvent refining lubricating oil base stocks from petroleum fractions containing both aromatic and nonaromatic constituents. The process utilizes n-methyl-2-pyrrolidone as a selective solvent for aromatic hydrocarbons wherein the refined oil fraction and the extract fraction are freed of final traces of solvent by stripping with gaseous ammonia. The process has several advantages over conventional processes including a savings in energy required for the solvent refining process, and reduced corrosion of the process equipment.

  4. Depression of calcium dynamics in cardiac myocytes--a common mechanism of halogenated hydrocarbon anesthetics and solvents.

    PubMed

    Hoffmann, P; Heinroth, K; Richards, D; Plews, P; Toraason, M

    1994-05-01

    Individual halogenated hydrocarbons (HC) have recently been demonstrated to depress Ca2+ dynamics in cardiomyocytes during excitation-contraction coupling. In the present study, eight widely used HC were systematically compared for their effects on Ca2+ dynamics in neonatal rat cardiomyocytes by means of spectrofluorometric analysis of fura-2-Ca(2+)-binding. Cells were exposed to dichloromethane (DCM), dichloroethane (DCE), 1,1,2-trichloroethane (112-TCE), trichloroethylene (TRI), halothane (HAL), 1,1,1-trichloroethane (111-TCE), perchloroethylene (PER), or pentachlorethane (PCE) in an environmentally controlled chamber. All HC tested decreased the height of electrically induced cytosolic free Ca2+ ([Ca2+]i) transients in a concentration-dependent and reversible manner (IC50 0.15-18.06 mM) without significant effects on diastolic [Ca2+]i. The increase in [Ca2+]i induced by depolarization with 90 mM KCl was inhibited to a lesser degree. Investigations with thapsigargin (100 nM) and ryanodine (1 microM)-inhibitors of Ca2+ release from the sarcoplasmic reticulum-provided evidence that the tonic Ca2+ response after KCl depolarization depends mainly on sarcolemmal Ca2+ influx. The potency of the eight HC to inhibit Ca2+ dynamics in cardiomyocytes correlated with their octanol/water partition coefficients. Results support the hypothesis that alteration of Ca2+ dynamics in cardiomyocytes is a common mechanism of cardiotoxic HC actions. PMID:8072012

  5. Emulsification liquid-liquid microextraction based on deep eutectic solvent: An extraction method for the determination of benzene, toluene, ethylbenzene and seven polycyclic aromatic hydrocarbons from water samples.

    PubMed

    Khezeli, Tahere; Daneshfar, Ali; Sahraei, Reza

    2015-12-18

    In this study, for the first time, a simple, inexpensive and sensitive method named emulsification liquid-liquid microextraction based on deep eutectic solvent (ELLME-DES) was used for the extraction of benzene, toluene, ethylbenzene (BTE) and seven polycyclic aromatic hydrocarbons (PAHs) from water samples. In a typical experiment, 100μL of DES (as water-miscible extraction solvent) was added to 1.5mL of sample solution containing target analytes. A homogeneous solution was formed immediately. Injection of 100μL of THF (as emulsifier agent) into homogeneous solution provided a turbid state. After extraction, phase separation (aqueous phase/DES rich phase) was performed by centrifugation. DES rich phase was withdrawn by a micro-syringe and submitted to isocratic reverse-phase HPLC with UV detection. Under optimum conditions obtained by response surface methodology (RSM) and desirability function (DF), the calibration graphs were linear in the concentration range from 10 to 200μg/L for benzene, 10-400μg/L for toluene, 1-400μg/L for ethylbenzene, biphenyl, chrysene and fluorene, and 0.1-400μg/L for anthracene, benzo[a]pyrene, phenanthrene and pyrene. The coefficients of determination (r(2)) and limits of detection were 0.9924-0.9997 and 0.02-6.8μg/L, respectively. This procedure was successfully applied to the determination of target analytes in spiked water samples. The relative mean recoveries ranged from 93.1 to 103.3%. PMID:26614169

  6. Au/SiO{sub x} composite thin film as catalyst for solvent-free hydrocarbon oxidation

    SciTech Connect

    Han, Xiao; Huang, Hui; Zhang, Hengchao; Zhang, Xing; Li, Haitao; Liu, Ruihua; Liu, Yang Kang, Zhenhui

    2013-10-15

    Graphical abstract: Au/SiO{sub x} composite thin film possesses high catalytic activity and stability for selective oxidation of cis-cyclooctene. - Highlights: • Au/SiO{sub x} composite thin film was synthesized by a facile and efficient chemical approach. • The Au/SiO{sub x} composite thin film exhibits high catalytic ability for the selective oxidation. • The Au/SiO{sub x} composite thin film possesses high structural and catalytic stability. - Abstract: We report a facile and efficient chemical approach for the controllable preparation of Au/SiO{sub x} composite thin film using silicon quantum dots as SiO{sub x} sources. Au/SiO{sub x} composite thin film exhibits high catalytic activity (65.04% conversion based on cis-cyclooctene and 78.34% selectivity for 2-hydroxycyclooctanone) and stability for selective oxidation of cis-cyclooctene in the absence of solvent using TBHP as radical initiator and oxygen (in the air) as oxidant at 80 °C.

  7. J-aggregation, its impact on excited state dynamics and unique solvent effects on macroscopic assembly of a core-substituted naphthalenediimide

    NASA Astrophysics Data System (ADS)

    Kar, Haridas; Gehrig, Dominik W.; Laquai, Frédéric; Ghosh, Suhrit

    2015-04-01

    Herein we reveal a straightforward supramolecular design for the H-bonding driven J-aggregation of an amine-substituted cNDI in aliphatic hydrocarbons. Transient absorption spectroscopy reveals sub-ps intramolecular electron transfer in isolated NDI molecules in a THF solution followed by a fast recombination process, while a remarkable extension of the excited state lifetime by more than one order of magnitude occurred in methylcyclohexane likely owing to an increased charge-separation as a result of better delocalization of the charge-separated states in J-aggregates. We also describe unique solvent-effects on the macroscopic structure and morphology. While J-aggregation with similar photophysical characteristics was noticed in all the tested aliphatic hydrocarbons, the morphology strongly depends on the ``structure'' of the solvents. In linear hydrocarbons (n-hexane, n-octane, n-decane or n-dodecane), formation of an entangled fibrillar network leads to macroscopic gelation while in cyclic hydrocarbons (methylcyclohexane or cyclohexane) although having a similar polarity, the cNDI exhibits nanoscale spherical particles. These unprecedented solvent effects were rationalized by establishing structure-dependent specific interactions of the solvent molecules with the cNDI which may serve as a general guideline for solvent-induced morphology-control of structurally related self-assembled materials.Herein we reveal a straightforward supramolecular design for the H-bonding driven J-aggregation of an amine-substituted cNDI in aliphatic hydrocarbons. Transient absorption spectroscopy reveals sub-ps intramolecular electron transfer in isolated NDI molecules in a THF solution followed by a fast recombination process, while a remarkable extension of the excited state lifetime by more than one order of magnitude occurred in methylcyclohexane likely owing to an increased charge-separation as a result of better delocalization of the charge-separated states in J-aggregates. We

  8. One-step solvent extraction followed by liquid chromatography-atmospheric pressure photoionization tandem mass spectrometry for the determination of polycyclic aromatic hydrocarbons in edible oils.

    PubMed

    Shi, Long-Kai; Liu, Yu-Lan; Liu, Hua-Min; Zhang, Ming-Ming

    2015-05-01

    A method for rapid analysis of 16 polycyclic aromatic hydrocarbons (PAHs) in edible oils has been developed on the basis of a simplified solvent extraction and liquid chromatography-atmospheric pressure photoionization tandem mass spectrometry performed in multiple reaction monitoring mode. The briefness of the experimental procedure, the use of milliliters of acetonitrile for extraction without any further cleanup process, the short analysis time, and the excellent sensitivity and selectivity demonstrated the advantages of this practical and environmentally friendly method. All the analytes exhibited satisfactory recoveries at three spiking levels (the recoveries ranged from 77.8 to 106.4%), and the relative standard deviations were lower than 10%. The limits of quantitation of this method for the 16 PAHs were in the range of 0.02-0.43 μg/kg. The validated method was successfully applied for the determination of PAHs in coconut oil reference material (BCR-458) and real edible oil samples. The results suggested that a large-scale investigation of the concentration of PAHs in vegetable oils in China is required. PMID:25725580

  9. Halogenated hydrocarbon solvent-related cholangiocarcinoma risk: biliary excretion of glutathione conjugates of 1,2-dichloropropane evidenced by untargeted metabolomics analysis.

    PubMed

    Toyoda, Yu; Takada, Tappei; Suzuki, Hiroshi

    2016-01-01

    Recently, the International Agency for Research on Cancer issued a warning about the carcinogenicity of 1,2-dichloropropane (1,2-DCP) to humans based on an epidemiological study suggesting a relationship between the incidence of cholangiocarcinoma and occupational exposure to halogenated hydrocarbon solvent comprised mostly of 1,2-DCP. Although this dihaloalkane has been used in various industrial fields, there has been no biological evidence explaining the cholangiocarcinoma latency, as well as little understanding of general cholangiocarcinoma risk. In the present study, we explored the biliary excretion of 1,2-DCP metabolites by an untargeted metabolomics approach and the related molecular mechanism with in vitro and in vivo experiments. We hypothesized that the biliary excretion of carcinogens derived from 1,2-DCP contribute to the increased cholangiocarcinoma risk. We found that 1,2-DCP was conjugated with glutathione in the liver, and that the glutathione-conjugated forms of 1,2-DCP, including a potential carcinogen that contains a chloride atom, were excreted into bile by the bile canalicular membrane transporter, ABCC2. These results may reflect a risk in the backfiring of biliary excretion as a connatural detoxification systems for xenobiotics. Our findings would contribute to uncover the latent mechanism by which the chronic exposure to 1,2-DCP increases cholangiocarcinoma risk and future understanding of cholangiocarcinoma biology. PMID:27087417

  10. Hydrocarbons in Washington coastal sediments

    NASA Astrophysics Data System (ADS)

    Prahl, Fredrick G.; Carpenter, Roy

    1984-06-01

    The sources and distributions of polycyclic aromatic hydrocarbons (PAH) and aliphatic hydrocarbons are characterized in seventeen sediments from a highly river-influenced sedimentary environment off the southwestern coast of Washington. The major hydrocarbons are land-derived, introduced as preformed compounds and display long-term stability in sediment cores. A series of PAH of anthropogenic origin and two naturally derived compounds, retene and perylene, dominate the PAH composition in these sediments. Plantwax n-alkanes are the major aliphatic hydrocarbon constituents. Aliphatic hydrocarbons of marine origin, pristane and a series of four acyclic, multibranched C 25 polyolefins, are also observed in many sediments. The concentrations of these marine-derived hydrocarbons decrease to negligible levels rapidly with sediment depth from the sea-sediment interface, suggesting degradation. In general, the major land-derived hydrocarbons are concentrated in the midshelf silt deposit which extends northwestward along the continental shelf from the Columbia River mouth. A quantitatively more minor, natural series of phenanthrene homologs, also of terrestrial origin, is preferentially advected further offshore and deposited in continental slope sediments. These distributions are consistent with recognized particle associations for these compounds and sediment dispersal processes in this coastal environment. Sediment core records suggest the present pattern of dispersal has persisted for at least the past century and possibly since the Late Pleistocene.

  11. Liquid-liquid equilibria for mixtures of an alkane + an aromatic hydrocarbon + 1,4-dicyanobutane at 298.15 K

    SciTech Connect

    Letcher, T.M.; Naicker, P.K.

    2000-02-01

    The separation of pure aromatic and aliphatic compounds from their mixtures is an important goal in chemical operations (e.g., Fischer-Tropsch synthesis) that produce both types of compounds. In this work the authors have used 1,4-dicyanobutane (DCB) as a potential solvent for this separation. Liquid-liquid equilibrium results for mixtures of an alkane + an aromatic hydrocarbon + 1,4-dicyanobutane at 298.15 K are reported, where the alkane is hexane or nonane or dodecane or hexadecane and the aromatic hydrocarbon is benzene or methylbenzene or 1,2-dimethylbenzene, or 1,3-dimethylbenzene, or 1,4-dimethylbenzene or 1,3,5-trimethylbenzene or ethylbenzene. The results show that there is a small increase in the two-phase region as the chain length of the alkane is increased. The type of aromatic hydrocarbon present in the mixture has a noticeable effect on the slopes of the tie lines. There is also an increase in the area of the two phase-region with increasing substitution of methyl groups on the benzene ring. NRTL and UNIQUAC models were correlated to the data. The results show that 1,4-dicyanobutane may be used as a solvent for the separation of aromatic and aliphatic hydrocarbons.

  12. Dissolution of biological samples in deep eutectic solvents: an approach for extraction of polycyclic aromatic hydrocarbons followed by liquid chromatography-fluorescence detection.

    PubMed

    Helalat-Nezhad, Zahra; Ghanemi, Kamal; Fallah-Mehrjardi, Mehdi

    2015-05-15

    A novel sample preparation method based on the complete dissolution of marine biological samples in choline chloride-oxalic acid (ChCl-Ox) deep eutectic solvent was developed for fast and efficient extraction of eight polycyclic aromatic hydrocarbons (PAHs) using minimum volumes of cyclohexane. The extracted PAHs were purified and then measured by high-performance liquid chromatography-fluorescence detection (HPLC-FL). The effect of key parameters on extraction recoveries and precision was investigated. At optimized conditions, the studied samples were dissolved under atmospheric pressure in ChCl-Ox (1:2) at 55°C for 30min, which is considerably lower than the temperature used in the classical and current methods. After dissolution, it took approximately 20min to quantitatively extract the PAHs from ChCl-Ox using 5mL cyclohexane. Depending on the analyte, the developed method was linear over the calibration range 1.0-250, 2.0-250, and 5.0-250ngg(-1), with r(2)>0.996. The detection limits of the method were between 0.50 and 3.08ngg(-1). The intra-day and inter-day precisions (based on the relative standard deviation, n=5) of the spiked PAHs at a concentration level of 50ngg(-1) were better than 12.6% and 13.3%, respectively. Individual PAH recoveries from spiked marine fish and macroalgae samples were in the range of 71.6% to 109.6%. For comparison, the spiked samples were also subjected to the Soxhlet extraction method. The simplicity of the procedure, high extraction efficiency, short analysis time, and use of safe and inexpensive components suggest the proposed method has a high potential for utilization in routine trace PAH analysis in biological samples. PMID:25857544

  13. 40 CFR 721.3364 - Aliphatic ether.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Aliphatic ether. 721.3364 Section 721... Aliphatic ether. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as an aliphatic ether (PMN P-93-1381) is subject to reporting under...

  14. 40 CFR 721.3364 - Aliphatic ether.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Aliphatic ether. 721.3364 Section 721... Aliphatic ether. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as an aliphatic ether (PMN P-93-1381) is subject to reporting under...

  15. Classification of Solvents according to Interaction Mechanisms.

    ERIC Educational Resources Information Center

    Ahmed, Wasi

    1979-01-01

    Presented is a model for solvent effects based on the observation that the excitation energy of all-trans-N-Retinylidenmethyl-n-butylammonium iodide is directly related to the dielectric constant of a series of aromatic and aliphatic solvents as the dielectric constant (e) ranges from 2 to 10.5. (BT)

  16. Process for extracting hydrocarbons from hydrocarbon bearing ores

    SciTech Connect

    Friedman, R.H.; Eakin, B.E.

    1986-02-18

    This patent describes a process for recovering hydrocarbons from a diatomite ore consisting of: reducing the size of the ore to less than about 5 mesh to form a reduced ore; combining the reduced ore with liquid to form ore pellets; treating the ore pellets to form extractable ore pellets; contacting a bed of the extractable pellets with extracting solvent in an extraction zone such that the relative velocity of the solvent to the extractable pellets is at least about one-half gallon per square foot per minute or more to thereby extract hydrocarbons from the extractable pellets and form spent pellets and a hydrocarbon rich solvent stream comprising extracting solvent and extracted hydrocarbons. The extracted hydrocarbons have an ash content of about less than 3 weight percent; and recovering extracting solvent from the spent pellets while retaining the spent pellets in pellet form without release of a significant amount of fines.

  17. Guided desaturation of unactivated aliphatics

    NASA Astrophysics Data System (ADS)

    Voica, Ana-Florina; Mendoza, Abraham; Gutekunst, Will R.; Fraga, Jorge Otero; Baran, Phil S.

    2012-08-01

    The excision of hydrogen from an aliphatic carbon chain to produce an isolated olefin (desaturation) without overoxidation is one of the most impressive and powerful biosynthetic transformations for which there are no simple and mild laboratory substitutes. The versatility of olefins and the range of reactions they undergo are unsurpassed in functional group space. Thus, the conversion of a relatively inert aliphatic system into its unsaturated counterpart could open new possibilities in retrosynthesis. In this article, the invention of a directing group to achieve such a transformation under mild, operationally simple, metal-free conditions is outlined. This ‘portable desaturase’ (TzoCl) is a bench-stable, commercial entity (Aldrich, catalogue number L510092) that is facile to install on alcohol and amine functionalities to ultimately effect remote desaturation, while leaving behind a synthetically useful tosyl group.

  18. Combinatorics of aliphatic amino acids.

    PubMed

    Grützmann, Konrad; Böcker, Sebastian; Schuster, Stefan

    2011-01-01

    This study combines biology and mathematics, showing that a relatively simple question from molecular biology can lead to complicated mathematics. The question is how to calculate the number of theoretically possible aliphatic amino acids as a function of the number of carbon atoms in the side chain. The presented calculation is based on earlier results from theoretical chemistry concerning alkyl compounds. Mathematical properties of this number series are highlighted. We discuss which of the theoretically possible structures really occur in living organisms, such as leucine and isoleucine with a chain length of four. This is done both for a strict definition of aliphatic amino acids only involving carbon and hydrogen atoms in their side chain and for a less strict definition allowing sulphur, nitrogen and oxygen atoms. While the main focus is on proteinogenic amino acids, we also give several examples of non-proteinogenic aliphatic amino acids, playing a role, for instance, in signalling. The results are in agreement with a general phenomenon found in biology: Usually, only a small number of molecules are chosen as building blocks to assemble an inconceivable number of different macromolecules as proteins. Thus, natural biological complexity arises from the multifarious combination of building blocks. PMID:21120449

  19. IN-SITU AQUIFER RESTORATION OF CHLORINATED ALIPHATICS BY METHANOTROPHIC BACTERIA

    EPA Science Inventory

    This project evaluated the potential of enhanced in-situ biotransformation of chlorinated aliphatic solvents by a bacterial community grown on methane under aerobic conditions. The target chlorinated compounds were trichloroethene (TCE), cis-and trans-1,2-dichloroethene (DCE), an...

  20. THE CARRIERS OF THE INTERSTELLAR UNIDENTIFIED INFRARED EMISSION FEATURES: AROMATIC OR ALIPHATIC?

    SciTech Connect

    Li Aigen; Draine, B. T. E-mail: draine@astro.princeton.edu

    2012-12-01

    The unidentified infrared emission (UIE) features at 3.3, 6.2, 7.7, 8.6, and 11.3 {mu}m, commonly attributed to polycyclic aromatic hydrocarbon (PAH) molecules, have been recently ascribed to coal- or kerogen-like organic nanoparticles with a mixed aromatic-aliphatic structure. However, we show in this Letter that this hypothesis is inconsistent with observations. We estimate the aliphatic fraction of the UIE carriers based on the observed intensities of the 3.4 {mu}m and 6.85 {mu}m emission features by attributing them exclusively to aliphatic C-H stretch and aliphatic C-H deformation vibrational modes, respectively. We derive the fraction of carbon atoms in aliphatic form to be <15%. We conclude that the UIE emitters are predominantly aromatic, with aliphatic material at most a minor part of the UIE carriers. The PAH model is consistent with astronomical observations and PAHs dominate the strong UIE bands.

  1. Contact solid-phase microextraction with uncoated glass and polydimethylsiloxane-coated fibers versus solvent sampling for the determination of hydrocarbons in adhesion secretions of Madagascar hissing cockroaches Gromphadorrhina portentosa (Blattodea) by gas chromatography-mass spectrometry.

    PubMed

    Gerhardt, Heike; Schmitt, Christian; Betz, Oliver; Albert, Klaus; Lämmerhofer, Michael

    2015-04-01

    Molecular profiles of adhesion secretions of Gromphadorrhina portentosa (Madagascar hissing cockroach, Blattodea) were investigated by gas chromatography mass spectrometry with particular focus on a comprehensive analysis of linear and branched hydrocarbons. For this purpose, secretions from the tarsi (feet), possibly contributing to adhesion on smooth surfaces, and control samples taken from the tibiae (lower legs), which contain general cuticular hydrocarbons that are supposed to be not involved in the biological adhesion function, were analyzed and their molecular fingerprints compared. A major analytical difficulty in such a study constitutes the representative, spatially controlled, precise and reproducible sampling from a living insect as well as the minute quantities of insect secretions on both tarsi and tibiae. Thus, three different in vivo sampling methods were compared in terms of sampling reproducibility and extraction efficiency by replicate measurement of samples from tarsi and tibiae. While contact solid-phase microextraction (SPME) with a polydimethylsiloxane (PDMS) fiber showed higher peak intensities, a self-made uncoated glass fiber had the best repeatability in contact-SPME sampling. Chromatographic profiles of these two contact-SPME sampling methods were statistically not significantly different. Inter-individual variances were larger than potentially existing minor differences in molecular patterns of distinct sampling methods. Sampling by solvent extraction was time consuming, showed lower sensitivities and was less reproducible. In general, sampling by contact-SPME with a cheap glass fiber turned out to be a viable alternative to PDMS-SPME sampling. Hydrocarbon patterns of the tarsal adhesion secretions were qualitatively similar to those of epicuticular hydrocarbon profiles of the tibiae. However, hydrocarbons were in general less abundant in tarsal secretions than secretions from tibiae. PMID:25728659

  2. Two-step catalytic hydrodeoxygenation of fast pyrolysis oil to hydrocarbon liquid fuels.

    PubMed

    Xu, Xingmin; Zhang, Changsen; Liu, Yonggang; Zhai, Yunpu; Zhang, Ruiqin

    2013-10-01

    Two-step catalytic hydrodeoxygenation (HDO) of fast pyrolysis oil was investigated for translating pyrolysis oil to transportation grade hydrocarbon liquid fuels. At the first mild HDO step, various organic solvents were employed to promote HDO of bio-oil to overcome coke formation using noble catalyst (Ru/C) under mild conditions (300 °C, 10 MPa). At the second deep HDO step, conventional hydrogenation setup and catalyst (NiMo/Al2O3) were used under severe conditions (400 °C, 13 MPa) for obtaining hydrocarbon fuel. Results show that the phenomenon of coke formation is effectively eliminated, and the properties of products have been significantly improved, such as oxygen content decreases from 48 to 0.5 wt% and high heating value increases from 17 to 46 MJ kg(-1). GC-MS analysis indicates that the final products include C11-C27 aliphatic hydrocarbons and aromatic hydrocarbons. In short, the fast pyrolysis oils were successfully translated to hydrocarbon liquid fuels using a two-step catalytic HDO process. PMID:23876507

  3. A simple McGowan specific volume correction for branching in hydrocarbons and its consequences for some other solvation parameter values.

    PubMed

    van Noort, Paul C M; Haftka, Joris J H; Parsons, John R

    2011-08-01

    Differences in molecular properties between linear and branched alkanes as well as between compounds with branched alkyl groups is of relevance due to the large number of branched isomers of environmentally relevant compounds (e.g. fuels, fuel additives, surfactants). For branched alkane vapor pressures, the McGowan specific volume is a poor predictor. Therefore, in this study a correction on the McGowan specific volume is derived in terms of the number of branches and the number of pairs of vicinal branches to improve the prediction of branched alkane vapor pressures. This branching correction also brought branched/alkane solvent accessible volumes, octanol/water partition coefficients, air/hexadecane partition coefficients, and aqueous solubilities as well as alkyl-branched substituted aliphatic hydrocarbon air/hexadecane partition coefficients more in line with corresponding linear hydrocarbon properties when compared on a McGowan specific volume basis. Even for air-hexadecane partition coefficients of substituted aliphatic hydrocarbons with substituents at non-terminal carbons, application of the branching correction to the carbon bearing the substituent caused these partition coefficients to be more in line with those for linear compounds. Values for the Abraham A and B solvation parameters for nonlinear aliphatic ethers, amines, and alcohols, recalculated using branching corrected McGowan specific volumes, turned out to be closer to chemical expectations based on linear aliphatic ether, amine and alcohol values compared to previously reported experimental values obtained using uncorrected McGowan specific volumes. A comparison of alkylbenzene and alkene partition coefficient estimates from two different linear solvation energy relations, one containing a McGowan specific volume term and one without such a term, suggests that no branching correction is needed for alkyl groups at sp2 carbons. The main advantage of using branching corrected McGowan specific

  4. Solvent substitution for electronic products

    SciTech Connect

    Benkovich, M.K.

    1992-01-01

    Allied-Signal Inc., Kansas City Division (KCD), manufactures the electrical, electrochemical, mechanical, and plastic components for nuclear weapons. The KCD has made a commitment to eliminate the use of chlorohydrocarbon (CHC) and chlorofluorocarbon (CFC) solvents to the greatest technical extent possible consistent with nuclear safety and stockpile reliability requirements. Current cleaning processes in the production departments use trichloroethylene, 1,1,1-trichloroethane, and various CFC-113 based solvents. Several non-halogenated solvents (Solvent A - an aqueous solvent based on N,N-dimethylacetamide, Solvent B - an aqueous mixture of ethanol amines, Solvent C - a hydrocarbon solvent based on octadecyl acetate, Solvent D - a terpene (d-limonene) hydrocarbon solvent combined with emulsifiers, Solvent E - a terpene (d-limonene) hydrocarbon solvent combined with a separation agent, d-limonene, and isopropyl alcohol) were evaluated to determine the most effective, non-chlorinated, non-fluorinated, alternate solvent cleaning system. All of these solvents were evaluated using current manual spray cleaning processes. The solvents were evaluated for their effectiveness in removing a rosin based RMA solder flux, a particular silicone mold release, and oils, greases, mold releases, resins, etc. The Meseran Surface Analyzer was used to measure organic contamination on the samples before and after cleaning. An Omega Meter Model 600 was also used to detect solder flux residues. Solvents C, D, E and d-limonene the best alternatives to trichloroethylene for removing all of the contaminants tested. For this particular electronic assembly, d-limonene was chosen as the alternate because of material compatibility and long-term reliability concerns.

  5. Foaming of mixtures of pure hydrocarbons

    NASA Technical Reports Server (NTRS)

    Robinson, J. V.; Woods, W. W.

    1950-01-01

    Mixtures of pure liquid hydrocarbons are capable of foaming. Nine hydrocarbons were mixed in pairs, in all possible combinations, and four proportions of each combination. These mixtures were sealed in glass tubes, and the foaming was tested by shaking. Mixtures of aliphatic with other aliphatic hydrocarbons, or of alkyl benzenes with other alkyl benzenes, did not foam. Mixtures of aliphatic hydrocarbons with alkyl benzenes did foam. The proportions of the mixtures greatly affected the foaming, the maximum foaming of 12 of 20 pairs being at the composition 20 percent aliphatic hydrocarbon, 80 percent alkyl benzene. Six seconds was the maximum foam lifetime of any of these mixtures. Aeroshell 120 lubricating oil was fractionated into 52 fractions and a residue by extraction with acetone in a fractionating extractor. The index of refraction, foam lifetime, color, and viscosity of these fractions were measured. Low viscosity and high index fractions were extracted first. The viscosity of the fractions extracted rose and the index decreased as fractionation proceeded. Foam lifetimes and color were lowest in the middle fractions. Significance is attached to the observation that none of the foam lifetimes of the fractions or residue is as high as the foam lifetime of the original Aeroshell, indicating that the foaming is not due to a particular foaming constituent, but rather to the entire mixture.

  6. Dielectric relaxations in aliphatic polyesters

    NASA Astrophysics Data System (ADS)

    Sen, Sudeepto

    2001-07-01

    The dielectric technique was used to study the relaxation processes of five linear aliphatic polyesters. The polyesters studied were poly (ethylene succinate/adipate) or PESA, poly (trimethylene succinate/adipate) or PTSA, poly (butylene succinate/adipate) or PBSA, poly (ethylene succinate) or PES, and poly (ethylene adipate) or PEA. Three of the polyesters were copolymers (PESA, PTSA, and PBSA), and the remaining two (PES and PEA) were homopolymers. Two of the five were amorphous (PESA and PTSA), and the remaining three (PBSA, PES, and PEA) were semicrystalline. All the five polyesters were synthesized in the laboratory using a poly-condensation reaction between a series of aliphatic diols and diesters. The succinic and adipic groups in the copolymers are in equimolar amounts. The polymers were characterized by differential scanning calorimetry and density measurements. Elemental analysis done on the polymers confirmed that their compositions matched theoretical estimates. The relaxation processes were studied dielectrically using an IMASS time domain dielectric spectrometer (TDS) and an HP 4284A LCR meter. Together they allowed a frequency range from 0.001 Hz to 1 MHz. Typically in the subglass region, good data were obtained between 0.01 Hz and 100 kHz. In the glass transition region, good data were occasionally available over the entire range. Two relaxation processes were detected in the subglass temperature region for all the polymers, and in the case of the copolymers PTSA and PBSA, they were also well resolved. Both the processes showed Arrhenius behavior with modest activation energies characteristic of subglass processes in general. They also progressively merged with increasing temperature, which implies a lower activation energy for the faster process which is consistent with the current understanding of relaxation phenomena. The glass transition region of all the polymers also showed a merging of the dominant alpha relaxation with the subglass

  7. Mantle hydrocarbons: Abiotic or biotic?

    SciTech Connect

    Sugisaki, Ryuichi; Mimura, Koichi

    1994-06-01

    Analyses of 227 rocks from fifty localities throughout the world showed that mantle derived rocks such as tectonized peridotites in ophiolite sequences (tectonites) and peridotite xenoliths in alkali basalts contain heavier hydrocarbons (n-alkanes), whereas igneous rocks produced by magmas such as gabbro and granite lack them. The occurrence of hydrocarbons indicates that they were not derived either from laboratory contamination or from field contamination; these compounds found in the mantle-derived rocks are called here {open_quotes}mantle hydrocarbons.{close_quotes} The existence of hydrocarbons correlates with petrogenesis. For example, peridotite cumulates produced by magmatic differentiation lack hydrocarbons whereas peridotite xenoliths derived from the mantle contain them. Gas chromatographic-mass spectrometric records of the mantle hydrocarbons resemble those of aliphatics in meteorites and in petroleum. Features of the hydrocarbons are that (a) the mantle hydrocarbons reside mainly along grain boundaries and in fluid inclusions of minerals; (b) heavier isoprenoids such as pristane and phytane are present; and (c) {delta}{sup 13}C of the mantle hydrocarbons is uniform (about {minus}27{per_thousand}). Possible origins for the mantle hydrocarbons are as follows. (1) They were inorganically synthesized by Fischer-Tropsch type reaction in the mantle. (2) They were delivered by meteorites and comets to the early Earth. (3) They were recycled by subduction. The mantle hydrocarbons in the cases of (1) and (2) are abiogenic and those in (3) are mainly biogenic. It appears that hydrocarbons may survive high pressures and temperatures in the mantle, but they are decomposed into lighter hydrocarbon gases such as CH{sub 4} at lower pressures when magmas intrude into the crust; consequently, peridotite cumulates do not contain heavier hydrocarbons but possess hydrocarbon gases up to C{sub 4}H{sub 10}. 76 refs., 5 figs., 3 tabs.

  8. Mantle hydrocarbons: abiotic or biotic?

    PubMed

    Sugisaki, R; Mimura, K

    1994-06-01

    Analyses of 227 rocks from fifty localities throughout the world showed that mantle derived rocks such as tectonized peridotites in ophiolite sequences (tectonites) arid peridotite xenoliths in alkali basalts contain heavier hydrocarbons (n-alkanes), whereas igneous rocks produced by magmas such as gabbro arid granite lack them. The occurrence of hydrocarbons indicates that they were not derived either from laboratory contamination or from held contamination; these compounds found in the mantle-derived rocks are called here "mantle hydrocarbons." The existence of hydrocarbons correlates with petrogenesis. For example, peridotite cumulates produced by magmatic differentiation lack hydrocarbons whereas peridotite xenoliths derived from the mantle contain them. Gas chromatographic-mass spectrometric records of the mantle hydrocarbons resemble those of aliphatics in meteorites and in petroleum. Features of the hydrocarbons are that (a) the mantle hydrocarbons reside mainly along grain boundaries and in fluid inclusions of minerals; (b) heavier isoprenoids such as pristane and phytane are present; and (c) delta 13C of the mantle hydrocarbons is uniform (about -27%). Possible origins for the mantle hydrocarbons are as follows. (1) They were in organically synthesized by Fischer-Tropsch type reaction in the mantle. (2) They were delivered by meteorites and comets to the early Earth. (3) They were recycled by subduction. The mantle hydrocarbons in the cases of (1) and (2) are abiogenic and those in (3) are mainly biogenic. It appears that hydrocarbons may survive high pressures and temperatures in the mantle, but they are decomposed into lighter hydrocarbon gases such as CH4 at lower pressures when magmas intrude into the crust; consequently, peridotite cumulates do not contain heavier hydrocarbons but possess hydrocarbon gases up to C4H10. PMID:11541663

  9. Mantle hydrocarbons: Abiotic or biotic?

    NASA Astrophysics Data System (ADS)

    Sugisaki, Ryuichi; Mimura, Koichi

    1994-06-01

    Analyses of 227 rocks from fifty localities throughout the world showed that mantle derived rocks such as tectonized peridotites in ophiolite sequences (tectonites) and peridotite xenoliths in alkali basalts contain heavier hydrocarbons ( n-alkanes), whereas igneous rocks produced by magmas such as gabbro and granite lack them. The occurrence of hydrocarbons indicates that they were not derived either from laboratory contamination or from field contamination; these compounds found in the mantle-derived rocks are called here "mantle hydrocarbons." The existence of hydrocarbons correlates with petrogenesis. For example, peridotite cumulates produced by magmatic differentiation lack hydrocarbons whereas peridotite xenoliths derived from the mantle contain them. Gas Chromatographic—mass spectrometric records of the mantle hydrocarbons resemble those of aliphatics in meteorites and in petroleum. Features of the hydrocarbons are that (a) the mantle hydrocarbons reside mainly along grain boundaries and in fluid inclusions of minerals (b) heavier isoprenoids such as pristane and phytane are present (c) δ13C of the mantle hydrocarbons is uniform (about -27%.). Possible origins for the mantle hydrocarbons are as follows. (1) They were inorganically synthesized by Fischer-Tropsch type reaction in the mantle. (2) They were delivered by meteorites and comets to the early Earth. (3) They were recycled by subduction. The mantle hydrocarbons in the cases of (1) and (2) are abiogenic and those in (3) are mainly biogenic. It appears that hydrocarbons may survive high pressures and temperatures in the mantle, but they are decomposed into lighter hydrocarbon gases such as CH 4 at lower pressures when magmas intrude into the crust; consequently, peridotite cumulates do not contain heavier hydrocarbons but possess hydrocarbon gases up to C 4H 10.

  10. Organic solvent-induced changes in membrane geometry in human SH-SY5Y neuroblastoma cells - a common narcotic effect?

    PubMed

    Meulenberg, Cécil J W; de Groot, Aart; Westerink, Remco H S; Vijverberg, Henk P M

    2016-07-01

    Exposure to organic solvents may cause narcotic effects. At the cellular level, these narcotic effects have been associated with a reduction in neuronal excitability caused by changes in membrane structure and function. In order to critically test whether changes in membrane geometry contribute to these narcotic effects, cultured human SH-SY5Y neuroblastoma cells have been exposed to selected organic solvents. The solvent-induced changes in cell membrane capacitance were investigated using the whole-cell patch clamp technique for real-time capacitance measurements. Exposure of SH-SY5Y cells to the cyclic hydrocarbons m-xylene, toluene, and cyclohexane caused a rapid and reversible increase of membrane capacitance. The aliphatic, nonpolar n-hexane did not cause a detectable change of whole-cell membrane capacitance, whereas the amphiphiles n-hexanol and n-hexylamine caused an increase of membrane capacitance and a concomitant reduction in membrane resistance. Despite a large difference in dielectric properties, the chlorinated hydrocarbons 1,1,2,2-tetrachoroethane and tetrachloroethylene caused a similar magnitude increase in membrane capacitance. The theory on membrane capacitance has been applied to deduce changes in membrane geometry caused by solvent partitioning. Although classical observations have shown that solvents increase the membrane capacitance per unit area of membrane, i.e., increase membrane thickness, the present results demonstrate that solvent partitioning predominantly leads to an increase in membrane surface area and to a lesser degree to an increase in membrane thickness. Moreover, the present results indicate that the physicochemical properties of each solvent are important determinants for its specific effects on membrane geometry. This implies that the hypothesis that solvent partitioning is associated with a common perturbation of membrane structure needs to be revisited and cannot account for the commonly observed narcotic effects of

  11. Alternative Green Solvents Project

    NASA Technical Reports Server (NTRS)

    Maloney, Phillip R.

    2012-01-01

    Necessary for safe and proper functioning of equipment. Mainly halogenated solvents. Tetrachloride, Trichloroethylene (TCE), CFC-113. No longer used due to regulatory/safety concerns. Precision Cleaning at KSC: Small % of total parts. Used for liquid oxygen (LOX) systems. Dual solvent process. Vertrel MCA (decafluoropentane (DFP) and trons-dichloroethylene) HFE-7100. DFP has long term environmental concerns. Project Goals: a) Identify potential replacements. b) 22 wet chemical processes. c) 3 alternative processes. d) Develop test procedures. e) Contamination and cleaning. f) Analysis. g) Use results to recommend alternative processes. Conclusions: a) No alternative matched Vertrel in this study. b) No clear second place solvent. c) Hydrocarbons- easy; Fluorinated greases- difficult. d) Fluorinated component may be needed in replacement solvent. e) Process may need to make up for shortcoming of the solvent. f) Plasma and SCC02 warrant further testing.

  12. Fatty acid alkyl esters as solvents: An evaluation of the kauri-butanol value. Comparison to hydrocarbons, dimethyl diesters and other oxygenates

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Esters, most commonly methyl esters, of vegetable oils or animal fats or other lipid feedstocks have found increasing use as an alternative diesel fuel known as biodiesel. However, biodiesel also has good solvent properties, a feature rendered additionally attractive by its biodegradability, low tox...

  13. SOLVENT FIRE BY-PRODUCTS

    SciTech Connect

    Walker, D; Samuel Fink, S

    2006-05-22

    Southwest Research Institute (SwRI) conducted a burn test of the Caustic-Side Solvent Extraction (CSSX) solvent to determine the combustion products. The testing showed hydrogen fluoride gas is not a combustion product from a solvent fire when up to 70% of the solvent is consumed. The absence of HF in the combustion gases may reflect concentration of the modifier containing the fluoride groups in the unburned portion. SwRI reported results for other gases (CO, HCN, NOx, formaldehyde, and hydrocarbons). The results, with other supporting information, can be used for evaluating the consequences of a facility fire involving the CSSX solvent inventory.

  14. Membrane separation of hydrocarbons

    DOEpatents

    Funk, Edward W.; Kulkarni, Sudhir S.; Chang, Y. Alice

    1986-01-01

    Mixtures of heavy oils and light hydrocarbons may be separated by passing the mixture over a polymeric membrane which comprises a polymer capable of maintaining its integrity in the presence of hydrocarbon compounds at temperature ranging from about ambient to about 100.degree. C. and pressures ranging from about 50 to about 1000 psi. The membranes which possess pore sizes ranging from about 10 to about 500 Angstroms are cast from a solvent solution and recovered.

  15. Coefficients of caffeine distribution in aliphatic alcohol-ammonium sulfate-water systems

    NASA Astrophysics Data System (ADS)

    Korenman, Ya. I.; Krivosheeva, O. A.; Mokshina, N. Ya.

    2012-11-01

    The extraction of caffeine with aliphatic alcohols C3-C9 from aqueous solutions in the presence of a salting-out agent (ammonium sulfate) is studied. Quantitative characteristics of extraction are calculated: the distribution coefficients ( D) and the degree of recovery ( R, %). Relations are found between log D of caffeine and the length of the hydrocarbon radical in the alcohol molecule, along with certain physicochemical properties of the extragents.

  16. Anaerobic digestion of aliphatic polyesters.

    PubMed

    Šmejkalová, Pavla; Kužníková, Veronika; Merna, Jan; Hermanová, Soňa

    2016-01-01

    Anaerobic processes for the treatment of plastic materials waste represent versatile and effective approach in environmental protection and solid waste management. In this work, anaerobic biodegradability of model aliphatic polyesters, poly(L-lactic acid) (PLA), and poly(ɛ-caprolactone) (PCL), in the form of powder and melt-pressed films with varying molar mass, was studied. Biogas production was explored in batch laboratory trials at 55 ± 1°C under a nitrogen atmosphere. The inoculum used was thermophilic digested sludge (total solids concentration of 2.9%) from operating digesters at the Central Waste Water Treatment Plant in Prague, Czech Republic. Methanogenic biodegradation of PCLs typically yielded from 54 to 60% of the theoretical biogas yield. The biodegradability of PLAs achieved from 56 to 84% of the theoretical value. High biogas yield (up to 677 mL/g TS) with high methane content (more than 60%), comparable with conventionally processed materials, confirmed the potential of polyester samples for anaerobic treatment in the case of their exploitation in agriculture or as a packaging material in the food industry. PMID:27191559

  17. Hydrocarbon pneumonia

    MedlinePlus

    Pneumonia - hydrocarbon ... Coughing Fever Shortness of breath Smell of a hydrocarbon product on the breath Stupor (decreased level of ... Most children who drink or inhale hydrocarbon products and develop ... hydrocarbons may lead to rapid respiratory failure and death.

  18. Measurement of hydrocarbon transport in bacteria

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Due to the hydrophobic, volatility, and relatively low aqueous solubility of aliphatic and aromatic hydrocarbons, transport of these chemicals by bacteria has not been extensively studied. These issues make transport assays difficult to carry out, and as a result, strong evidence for the active tran...

  19. Extracting hydrocarbons from water using a centrifuge

    NASA Astrophysics Data System (ADS)

    Ryabov, A. Yu.; Ilyina, A. A.; Chuikin, A. V.; Velikov, A. A.

    2014-09-01

    An original method for the solid-phase microextraction of hydrocarbons from water using a centrifuge is proposed. Comparative results from the chromatographic elution of substances after liquid-phase and solid-phase microextraction are presented. The percentage of the extraction of substances from aqueous solutions and the minimum detection limit for aromatic and aliphatic compounds are calculated.

  20. Mass spectrometry study of the sublimation of aliphatic dipeptides

    NASA Astrophysics Data System (ADS)

    Badelin, V. G.; Tyunina, E. Yu.; Krasnov, A. V.; Tyunina, V. V.; Giricheva, N. I.; Girichev, A. V.

    2012-03-01

    The sublimation of glycyl-L-α-alanine (Gly-Ala), L-α-alanyl-L-α-alanine (Ala-Ala), and DL-α-alanyl-DL-α-valine (Ala-Val) aliphatic dipeptides is studied by electron ionization mass spectrometry in combination with Knudsen effusion. The temperature range in which substances sublime as monomer molecular forms is determined. Enthalpies of sublimation Δs H°( T) are determined for Gly-Ala, Ala-Ala, and Ala-Val. It is shown that the enthalpy of sublimation of dipeptides increases with an increase in the side hydrocarbon radical. The unknown Δs H°(298) values for 17 amino acids and nine dipeptides are estimated using the proposed "structure-property" correlation model, in which the geometry and electron characteristics of molecules are used as structural descriptors.

  1. Isotopic and molecular analyses of hydrocarbons and monocarboxylic acids of the Murchison meteorite

    NASA Technical Reports Server (NTRS)

    Krishnamurthy, R. V.; Epstein, S.; Cronin, John R.; Pizzarello, Sandra; Yuen, George U.

    1992-01-01

    The monocarboxylic acids and hydrocarbons of the Murchison meteorite (CM2) were isolated for isotropic analysis. The nonvolatile hydrocarbons were analyzed as crude methanol and benzene-methanol extracts and also after separation by silica gel chromatography into predominantly aliphatic, aromatic, and polar hydrocarbon fractions. The volatile hydrocarbons were obtained after progressive decomposition of the meteorite matrix by freeze-thaw, hot water, and acid treatment. Molecular analyses of the aromatic hydrocarbons showed them to comprise a complex suite of compounds in which pyrene, fluoranthene, phenanthrene, and acenaphthene were the most abundant components, a result similar to earlier analyses. The polar hydrocarbons also comprise a very complex mixture in which aromatic ketones, nitrogen, and sulfur heterocycles were identified. The monocarboxylic acids, aliphatic, aromatic, and polar hydrocarbons, and the indigenous volatile hydrocarbons were found to be D-rich. The deuterium enrichment observed in these compounds is suggestive. In two separate analyses, the delta-D values of the nonvolatile hydrocarbons were observed to increase in the following order: aliphatic-aromatic-polar. This finding is consistent with an early solar system or parent body conversion of aromatic to aliphatic compounds as well as the suggestion of pyrolytic formation of aromatic from aliphatic compounds.

  2. DESTRUCTION OF HALOGENATED HYDROCARBONS WITH SOLVATED ELECTRONS IN THE PRESENCE OF WATER. (R826180)

    EPA Science Inventory

    Model halogenated aromatic and aliphatic hydrocarbons and halogenated phenols were dehalogenated in seconds by solvated electrons generated from sodium in both anhydrous liquid ammonia and ammonia/water solutions. The minimum sodium required to completely dehalogenate these mo...

  3. Solvent degradation products in nuclear fuel processing solvents

    SciTech Connect

    Shook, H.E. Jr.

    1988-06-01

    The Savannah River Plant uses a modified Purex process to recover enriched uranium and separate fission products. This process uses 7.5% tri-n-butyl phosphate (TBP) dissolved in normal paraffin hydrocarbons for the solvent extraction of a nitric acid solution containing the materials to be separated. Periodic problems in product decontamination result from solvent degradation. A study to improve process efficiency has identified certain solvent degradation products and suggested mitigation measures. Undecanoic acid, lauric acid, and tridecanoic acid were tentatively identified as diluent degradation products in recycle solvent. These long-chain organic acids affect phase separation and lead to low decontamination factors. Solid phase extraction (SPE) was used to concentrate the organic acids in solvent prior to analysis by high performance liquid chromatography (HPLC). SPE and HPLC methods were optimized in this work for analysis of decanoic acid, undecanoic acid, and lauric acid in solvent. Accelerated solvent degradation studies with 7.5% TBP in normal paraffin hydrocarbons showed that long-chain organic acids and long-chain alkyl butyl phosphoric acids are formed by reactions with nitric acid. Degradation of both tributyl phosphate and hydrocarbon can be minimized with purified normal paraffin replacing the standard grade presently used. 12 refs., 1 fig., 3 tabs.

  4. Aliphatic polyamines in physiology and diseases.

    PubMed

    Ramani, D; De Bandt, J P; Cynober, L

    2014-02-01

    Aliphatic polyamines are a family of polycationic molecules derived from decarboxylation of the amino acid ornithine that classically comprise three molecules: putrescine, spermidine and spermine. In-cell polyamine homeostasis is tightly controlled at key steps of cell metabolism. Polyamines are involved in an array of cellular functions from DNA stabilization, and regulation of gene expression to ion channel function and, particularly, cell proliferation. As such, aliphatic polyamines play an essential role in rapidly dividing cells such as in the immune system and digestive tract. Because of their role in cell proliferation, polyamines are also involved in carcinogenesis, prompting intensive research into polyamine metabolism as a target in cancer therapy. More recently, another aliphatic polyamine, agmatine, the decarboxylated derivative of arginine, has been identified as a neurotransmitter in mammals, and investigations have focused on its effects in the CNS, notably as a neuroprotector in brain injury. PMID:24144912

  5. Aliphatic amines in the Murchison meteorite

    NASA Technical Reports Server (NTRS)

    Jungclaus, G.; Cronin, J. R.; Moore, C. B.; Yuen, G. U.

    1976-01-01

    The paper reports on the determination of aliphatic amines in water extracts of the Murchison meteorite. The amines were analyzed by gas chromatography both as the free amines and as 2,4-dinitrophenyl (DNP) derivatives. The results give evidence for the presence of all of the possible primary aliphatic monoamines (eight) with fewer than five carbon atoms. Two of the seven possible secondary or tertiary aliphatic monoamines were identified. The identified primary amines total 80 nmol per g meteorite, and seem to be chemically or physically trapped in the meteorite. Similarities between the water-extractable amines and amino acids suggest that (1) a simple carbon compound, methane, for example, is the precursor of meteorite amines and amino acids, and (2) both amines and amino acids are extracted from the meteorite both as such and in the form of acid-hydrolyzable derivative or precursor species.

  6. Carbon isotope systematics of individual hydrocarbons in hydrothermal petroleum from Escanaba Trough, Northeastern Pacific Ocean

    USGS Publications Warehouse

    Simoneit, B.R.T.; Schoell, M.; Kvenvolden, K.A.

    1997-01-01

    We submitted individual aliphatic and polycyclic aromatic hydrocarbons in samples of hydrothermal petroleum from Escanaba trough to compound specific isotope analysis to trace their origins. The carbon isotope compositions of the alkanes and polycyclic aromatic hydrocarbons (means -27.5 and -24.7%, respectively) reflect a primarily terrestrial organic matter source.We submitted individual aliphatic and polycyclic aromatic hydrocarbons in samples of hydrothermal petroleum from Escanaba Trough to compound specific isotope analysis to trace their origins. The carbon isotope compositions of the alkanes and polycyclic aromatic hydrocarbons (means -27.5 and -24.7 per mill, respectively) reflect a primarily terrestrial organic matter source.

  7. Decrease of aliphatic CHs from diatoms by in situ heating infrared microspectroscopy

    NASA Astrophysics Data System (ADS)

    Alipour, Leila; Nakashima, Satoru

    2016-04-01

    In situ heating IR microspectroscopy at 260-300°C under air and N2 conditions has been conducted on diatom frustules to examine aliphatic CH losses during heating, simulating their changes with burial-diagenesis. Assuming a reaction model made up of two first-order kinetic relations, reaction rate constants k1 and k2 and activation energies (Ea) were evaluated for aliphatic CHs. The rate constants for loss of aliphatic CHs of diatom frustules under air and N2 flow are much larger, with much smaller activation energies (57-109 kJ/mol: air; 14-44 kJ/mol: N2), than those for conventional hydrocarbon generation reactions from kerogens (170-370 kJ/mol) studied at higher temperatures (350-450°C). The CH decrease rates are somewhat different from the amide I decrease (protein degradation) rates. The obtained results suggest that organic transformation reactions including degradation of aliphatic CHs inside the diatom silica frustules might be quite different from those of kerogens separated from the biological structures.

  8. Microbial degradation of aliphatic and aliphatic-aromatic co-polyesters.

    PubMed

    Shah, Aamer Ali; Kato, Satoshi; Shintani, Noboru; Kamini, Numbi Ramudu; Nakajima-Kambe, Toshiaki

    2014-04-01

    Biodegradable plastics (BPs) have attracted much attention since more than a decade because they can easily be degraded by microorganisms in the environment. The development of aliphatic-aromatic co-polyesters has combined excellent mechanical properties with biodegradability and an ideal replacement for the conventional nondegradable thermoplastics. The microorganisms degrading these polyesters are widely distributed in various environments. Although various aliphatic, aromatic, and aliphatic-aromatic co-polyester-degrading microorganisms and their enzymes have been studied and characterized, there are still many groups of microorganisms and enzymes with varying properties awaiting various applications. In this review, we have reported some new microorganisms and their enzymes which could degrade various aliphatic, aromatic, as well as aliphatic-aromatic co-polyesters like poly(butylene succinate) (PBS), poly(butylene succinate)-co-(butylene adipate) (PBSA), poly(ε-caprolactone) (PCL), poly(ethylene succinate) (PES), poly(L-lactic acid) (PLA), poly(3-hydroxybutyrate) and poly(3-hydoxybutyrate-co-3-hydroxyvalterate) (PHB/PHBV), poly(ethylene terephthalate) (PET), poly(butylene terephthalate) (PBT), poly(butylene adipate-co-terephthalate (PBAT), poly(butylene succinate-co-terephthalate) (PBST), and poly(butylene succinate/terephthalate/isophthalate)-co-(lactate) (PBSTIL). The mechanism of degradation of aliphatic as well as aliphatic-aromatic co-polyesters has also been discussed. The degradation ability of microorganisms against various polyesters might be useful for the treatment and recycling of biodegradable wastes or bioremediation of the polyester-contaminated environments. PMID:24522729

  9. Chlorinated aliphatic and aromatic VOC decomposition in air mixture by using electron beam irradiation

    NASA Astrophysics Data System (ADS)

    Chmielewski, A. G.; Sun, Yong-Xia; Bułka, S.; Zimek, Z.

    2004-09-01

    Chlorinated aliphatic and aromatic hydrocarbons, which are emitted from coal power station and waste incinerators, are very harmful to the environment and human health. Recent studies show that chlorinated aliphatic and aromatic hydrocarbons are suspected to be the precursors of dioxin's formation. Dioxin's emission into atmosphere will cause severe environmental problems by ecology contamination. l,4-dichlorobenzene(l,4-DCB) and cis-dichloroethylene( cis-DCE) were chosen as representative chlorinated aromatic and aliphatic compounds, respectively. Their decomposition was investigated by electron beam irradiation. The experiments were carried out "in batch" system. It is found that over 97% cis-DCE is decomposed having an initial concentration of 661 ppm. G-values of cis-DCE decomposition vary from 10 to 28 (molecules/100 eV) for initial concentration of 270-1530 ppm cis-DCE. The decomposition is mainly caused by secondary electron attachment and Cl addition reactions. Comparing with cis-DCE, 1,4-DCB decomposition needs higher absorbed dose. G-value of 1,4-DCB is below 4 molecules/100 eV.

  10. Comparison of Fluor Solvent and Selexol processes

    SciTech Connect

    Bucklin, R.W.; Schendel, R.L.

    1984-09-01

    Physical solvent processes can be useful for acid gas removal applications. The necessity for screening physical solvent characteristics to eliminate those solvents that are unsuitable or noncompetitive for a particular application is discussed. The Fluor Solvent and Selexol processes are compared. Selexol has an advantage over other solvents in oil applications involving H/sub 2/S and CO/sub 2/ removal in hydrocarbon systems. Fluor Solvent and Selexol have an experience advantage over other processes in applications for CO/sub 2/ removal only.

  11. RADIO FREQUENCY ENHANCED DECONTAMINATION OF SOILS CONTAMINATED WITH HALOGENATED HYDROCARBONS

    EPA Science Inventory

    There has been considerable effort in the development of innovative treatment technologies for the clean up of sites containing hazardous wastes such as hydrocarbons and chlorinated hydrocarbons. Typical examples of such waste material are: chlorinated solvents, polychlorinated b...

  12. Hydrocarbon components in carbonaceous meteorites

    NASA Astrophysics Data System (ADS)

    Kissin, Y. V.

    2003-05-01

    Currently, the presence of free n-alkanes and isoprenoid alkanes in carbonaceous meteorites is usually explained either by microbial contamination during the period between the meteorite fall and collection or by contamination from the environment of analytical laboratories and museums. The goal of this research was to repeat analysis of hydrocarbon components in meteorites and to investigate possible meteorite contamination routes discussed in the literature. Experimental analysis of free organic constituents in five carbonaceous meteorites by infrared spectroscopy (IR) and gas chromatographic (GC) methods confirmed the presence of extractable aliphatic components, n-alkanes in the C 15H 32-C 27H 56 range and isoprenoid alkanes (phytane, pristane, and norpristane), in some of these meteorites. The contents of these compounds vary depending on the source. Insoluble organic components of two meteorites (meteorite kerogens) were isolated, and their composition was analyzed by IR and cracking/GC methods. Comparison with the data on several terrestrial contamination sources proposed in the literature shows that the presence of free saturated hydrocarbons in meteorites and the composition of the meteorite kerogen could not be explained either by microbial contamination or by contamination from the laboratory environment. The types of the hydrocarbons in meteorites resemble those typical of ancient terrestrial deposits of organic-rich sediments, except for the absence of lighter hydrocarbons, which apparently slowly evaporated in space, and multi-ring naphthenic compounds of the biologic origin, steranes, terpanes, etc. The prevailing current explanation for the presence of free linear saturated hydrocarbons in carbonaceous meteorites, apart from contamination, is the abiotic route from hydrogen and carbon monoxide. However, the data on the structure of meteorite kerogens require a search for different routes that initially produce complex polymeric structures containing

  13. 40 CFR 721.10534 - Brominated aliphatic alcohol (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Brominated aliphatic alcohol (generic... Specific Chemical Substances § 721.10534 Brominated aliphatic alcohol (generic). (a) Chemical substance and... aliphatic alcohol (PMN P-12-260) is subject to reporting under this section for the significant new...

  14. 40 CFR 721.10534 - Brominated aliphatic alcohol (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Brominated aliphatic alcohol (generic... Specific Chemical Substances § 721.10534 Brominated aliphatic alcohol (generic). (a) Chemical substance and... aliphatic alcohol (PMN P-12-260) is subject to reporting under this section for the significant new...

  15. 40 CFR 721.3520 - Aliphatic polyglycidyl ether.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Aliphatic polyglycidyl ether. 721.3520... Substances § 721.3520 Aliphatic polyglycidyl ether. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance aliphatic polyglycidyl ether (PMN P-89-1036) is subject...

  16. 40 CFR 721.3520 - Aliphatic polyglycidyl ether.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Aliphatic polyglycidyl ether. 721.3520... Substances § 721.3520 Aliphatic polyglycidyl ether. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance aliphatic polyglycidyl ether (PMN P-89-1036) is subject...

  17. 40 CFR 721.2270 - Aliphatic dicarboxylic acid salt.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Aliphatic dicarboxylic acid salt. 721... Substances § 721.2270 Aliphatic dicarboxylic acid salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as aliphatic dicarboxylic...

  18. 40 CFR 721.2270 - Aliphatic dicarboxylic acid salt.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Aliphatic dicarboxylic acid salt. 721... Substances § 721.2270 Aliphatic dicarboxylic acid salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as aliphatic dicarboxylic...

  19. 40 CFR 721.2270 - Aliphatic dicarboxylic acid salt.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Aliphatic dicarboxylic acid salt. 721... Substances § 721.2270 Aliphatic dicarboxylic acid salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as aliphatic dicarboxylic...

  20. 40 CFR 721.2270 - Aliphatic dicarboxylic acid salt.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Aliphatic dicarboxylic acid salt. 721... Substances § 721.2270 Aliphatic dicarboxylic acid salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as aliphatic dicarboxylic...

  1. 40 CFR 721.6140 - Dialkyldithiophosphoric acid, aliphatic amine salt.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ..., aliphatic amine salt. 721.6140 Section 721.6140 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.6140 Dialkyldithiophosphoric acid, aliphatic amine salt. (a) Chemical... as a dialkyldithiophosphoric acid, aliphatic amine salt (P-90-1839) is subject to reporting...

  2. 40 CFR 721.6140 - Dialkyldithiophosphoric acid, aliphatic amine salt.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., aliphatic amine salt. 721.6140 Section 721.6140 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.6140 Dialkyldithiophosphoric acid, aliphatic amine salt. (a) Chemical... as a dialkyldithiophosphoric acid, aliphatic amine salt (P-90-1839) is subject to reporting...

  3. 40 CFR 721.6140 - Dialkyldithiophosphoric acid, aliphatic amine salt.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ..., aliphatic amine salt. 721.6140 Section 721.6140 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.6140 Dialkyldithiophosphoric acid, aliphatic amine salt. (a) Chemical... as a dialkyldithiophosphoric acid, aliphatic amine salt (P-90-1839) is subject to reporting...

  4. 40 CFR 721.6140 - Dialkyldithiophosphoric acid, aliphatic amine salt.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., aliphatic amine salt. 721.6140 Section 721.6140 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.6140 Dialkyldithiophosphoric acid, aliphatic amine salt. (a) Chemical... as a dialkyldithiophosphoric acid, aliphatic amine salt (P-90-1839) is subject to reporting...

  5. 40 CFR 721.6140 - Dialkyldithiophosphoric acid, aliphatic amine salt.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., aliphatic amine salt. 721.6140 Section 721.6140 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.6140 Dialkyldithiophosphoric acid, aliphatic amine salt. (a) Chemical... as a dialkyldithiophosphoric acid, aliphatic amine salt (P-90-1839) is subject to reporting...

  6. In-situ micro-FTIR Study of Thermal Changes of Organics in Tagish Lake Meteorite: Behavior of Aliphatic Oxygenated Functions and Effects of Minerals

    NASA Technical Reports Server (NTRS)

    Kebukawa, Yoko; Nakashima, Satoru; Nakamura-Messenger, Keiko; Zolensky, Michael E.

    2007-01-01

    Systematic in-situ FTIR heating experiments of Tagish Lake meteorite grains have been performed in order to study thermal stability of chondritic organics. Some aliphatic model organic substances have also been used to elucidate effects of hydrous phyllosilicate minerals on the thermal stability of organics. The experimental results indicated that organic matter in the Tagish Lake meteorite might contain oxygenated aliphatic hydrocarbons which are thermally stable carbonyls such as ester and/or C=O in ring compounds. The presence of hydrous phyllosilicate minerals has a pronounced effect on the increase of the thermal stability of aliphatic and oxygenated functions. These oxygenated aliphatic organics in Tagish Lake can be formed during the aqueous alteration in the parent body and the formation temperature condition might be less than 200 C, based especially on the thermal stability of C-O components. The hydrous phyllosilicates might provide sites for organic globule formation and protected some organic decomposition

  7. Quantitative Hydrocarbon Surface Analysis

    NASA Technical Reports Server (NTRS)

    Douglas, Vonnie M.

    2000-01-01

    The elimination of ozone depleting substances, such as carbon tetrachloride, has resulted in the use of new analytical techniques for cleanliness verification and contamination sampling. The last remaining application at Rocketdyne which required a replacement technique was the quantitative analysis of hydrocarbons by infrared spectrometry. This application, which previously utilized carbon tetrachloride, was successfully modified using the SOC-400, a compact portable FTIR manufactured by Surface Optics Corporation. This instrument can quantitatively measure and identify hydrocarbons from solvent flush of hardware as well as directly analyze the surface of metallic components without the use of ozone depleting chemicals. Several sampling accessories are utilized to perform analysis for various applications.

  8. TECHNICAL PROTOCOL FOR EVALUATING NATURAL ATTENUATION OF CHLORINATED SOLVENTS IN GROUND WATER

    EPA Science Inventory

    This Protocol is designed to evaluate the fate in ground water of chlorinated aliphatic hydrocarbons and/or fuel hydrocarbons. Documentation of natural attenuation requires detailed site characterization. The data collected under this protocol can be used to compare the relati...

  9. Renaissance of Aliphatic Polycarbonates: New Techniques and Biomedical Applications

    PubMed Central

    Xu, Jianwen; Feng, Ellva; Song, Jie

    2014-01-01

    Aliphatic polycarbonates were discovered a long time ago, with their conventional applications mostly limited to low molecular weight oligomeric intermediates for copolymerization with other polymers. Recent developments in polymerization techniques have overcome the difficulty in preparing high molecular weight aliphatic polycarbonates. These in turn, along with new functional monomers, have enabled the preparation of a wide range of aliphatic polycarbonates with diverse chemical compositions and structures. This review summarizes the latest polymerization techniques for preparing well-defined functional aliphatic polycarbonates, as well as the new applications of those aliphatic polycarbonates, esecially in the biomedical field. PMID:24994939

  10. Individual biotransformation rates in chlorinated aliphatic mixtures

    SciTech Connect

    Hughes, J.B.; Parkin, G.F.

    1996-02-01

    Anaerobic biotransformation of chlorinated aliphatics has been widely studied over the past decade, and anaerobic bioremediation is considered a promising technique for restoration of contaminated aquifers. Studies using batch cultures and continuously fed attached-growth systems investigated the effect of mixtures of chlorinated aliphatics on the anaerobic biotransformation rates of individual components of the mixture. Dichloromethane (DCM), chloroform (CF), and 1,1,1-trichloroethane (TCA) were selected for study because of their frequent detection in groundwater. Biotransformation of CF and TCA occurred in all systems. When CF and TCA were fed together, transformation rates for both aliphatics were lower than when fed individually. DCM generally had minor to negligible effects on the transformation of CF and TCA, but in one case, it caused a slight but statistically significant decrease in TCA transformation (p = 0.05). DCM transformation was not observed when fed individually or in mixtures to batch resting cultures, so the effect of CF and TCA on DCM transformation could not be determined.

  11. A study of hydrocarbons associated with brines from DOE geopressured wells

    SciTech Connect

    Keeley, D.F.

    1993-01-01

    Accomplishments are summarized on the following tasks: distribution coefficients and solubilities, DOE design well sampling, analysis of well samples, review of theoretical models of geopressured reservoir hydrocarbons, monitor for aliphatic hydrocarbons, development of a ph meter probe, DOE design well scrubber analysis, removal and disposition of gas scrubber equipment at Pleasant Bayou Well, and disposition of archived brines.

  12. Amine neutralized alkenylsuccinic anhydride propylene glycol adducts as corrosion inhibitors for hydrocarbon fuels

    SciTech Connect

    Meyer, G.R.

    1989-10-17

    This patent describes a corrosion inhibitor composition for hydrocarbon fuels from the group consisting of gasolines and diesel fuel oils. It comprises: a C{sub 10}-C{sub 24} alkenyl succinic anhydride esterified with between 0.5-1.5 moles of a water-soluble glycol and then neutralized with an aliphatic hydrocarbon amine.

  13. A study of hydrocarbons associated with brines from DOE geopressured wells. Final report

    SciTech Connect

    Keeley, D.F.

    1993-07-01

    Accomplishments are summarized on the following tasks: distribution coefficients and solubilities, DOE design well sampling, analysis of well samples, review of theoretical models of geopressured reservoir hydrocarbons, monitor for aliphatic hydrocarbons, development of a ph meter probe, DOE design well scrubber analysis, removal and disposition of gas scrubber equipment at Pleasant Bayou Well, and disposition of archived brines.

  14. Carbon isotope systematics of individual hydrocarbons in hydrothermal petroleum from Escanaba Trough, northeastern Pacific Ocean.

    PubMed

    Simoneit, B R; Schoell, M; Kvenvolden, K A

    1997-01-01

    We submitted individual aliphatic and polycyclic aromatic hydrocarbons in samples of hydrothermal petroleum from Escanaba Trough to compound specific isotope analysis to trace their origins. The carbon isotope compositions of the alkanes and polycyclic aromatic hydrocarbons (means -27.5 and -24.7%, respectively) reflect a primarily terrestrial organic matter source. PMID:11541391

  15. Isotopic analyses of nitrogenous compounds from the Murchison meteorite: ammonia, amines, amino acids, and polar hydrocarbons

    NASA Technical Reports Server (NTRS)

    Pizzarello, S.; Feng, X.; Epstein, S.; Cronin, J. R.

    1994-01-01

    The combined volatile bases (ammonia, aliphatic amines, and possibly other bases), ammonia, amino acids, and polar hydrocarbons were prepared from the Murchison meteorite for isotopic analyses. The volatile bases were obtained by cryogenic transfer after acid-hydrolysis of a hot-water extract and analyzed by combined gas chromatography-mass spectrometry of pentafluoropropionyl derivatives. The aliphatic amines present in this preparation comprise a mixture that includes both primary and secondary isomers through C5 at a total concentration of > or = 100 nmoles g-1. As commonly observed for meteoritic organic compounds, almost all isomers through C5 are present, and the concentrations within homologous series decrease with increasing chain length. Ammonia was chromatographically separated from the other volatile bases and found at a concentration of 1.1-1.3 micromoles g-1 meteorite. The ammonia analyzed includes contributions from ammonium salts and the hydrolysis of extractable organic compounds, e.g., carboxamides. Stable isotope analyses showed the volatile bases to be substantially enriched in the heavier isotopes, relative to comparable terrestrial compounds delta D < or = +1221%; delta 13C = +22%; delta 15N = +93%). Ammonia, per se, was found to have a somewhat lower delta 15N value (+69%) than the total volatile bases; consequently, a higher delta 15N (>93%) can be inferred for the other bases, which include the amines. Solvent-extractable polar hydrocarbons obtained separately were found to be enriched in 15N (delta 15N = +104%). Total amino acids, prepared from a hydrolyzed hot-water extract by cation exchange chromatography, gave a delta 15N of +94%, a value in good agreement with that obtained previously. Nitrogen isotopic data are also given for amino acid fractions separated chromatographically. The delta 15N values of the Murchison soluble organic compounds analyzed to date fall within a rather narrow range (delta 15N = +94 +/- 8%), an observation

  16. PRODUCTION OF FLUORINE-CONTAINING HYDROCARBON

    DOEpatents

    Sarsfield, N.F.

    1949-08-01

    This patent relates to improvements in the production of fluorine- containing hydrocarbon derivatives. The process for increasing the degree of fluorination of a fluorochlorohydrocarbon comprises subjecting a highly fluorinated fluorochlorohydrocarbon to the action of a dehydrochlorinating agent, and treating the resulting unsaturated body with fluorine, cobalt trifluoride, or silver difluoride. A number of reagents are known as dehydrochlorinaling agents, including, for example, the caustic alkalies, either in an anhydrous condition or dissolved in water or a lower aliphatic alcohol.

  17. Encephalopathy and vestibulopathy following short-term hydrocarbon exposure

    SciTech Connect

    Hodgson, M.J.; Furman, J.; Ryan, C.; Durrant, J.; Kern, E.

    1989-01-01

    Dizziness, headaches, and weakness occurred among three men after short-term hydrocarbon exposure during improper welding procedures in a closed container. Symptoms were related to objective evidence of vestibular and cognitive dysfunction. Symptoms and abnormal test results persisted for 6 to 18 months. Simulation of the accident failed to demonstrate likely exposures except aliphatic hydrocarbons, well within the permissible exposure levels. Short-term exposures to neurotoxins may lead to long-term central nervous system abnormalities.

  18. PETROLEUM HYDROCARBONS IN SEDIMENTS OF SAGINAW BAY, LAKE HURON

    EPA Science Inventory

    The history of petroleum contamination of Saginaw Bay is given by a 60 cm core recording sediment accumulation over the last two centuries. Aliphatic hydrocarbon concentrations average 385 micrograms/gm in modern sediments and progressively decrease from 10 cm to 40 cm in the cor...

  19. Hydrocarbons on Phoebe, Iapetus, and Hyperion: Quantitative Analysis

    NASA Technical Reports Server (NTRS)

    Cruikshank, Dale P.; MoreauDalleOre, Cristina; Pendleton, Yvonne J.; Clark, Roger Nelson

    2012-01-01

    We present a quantitative analysis of the hydrocarbon spectral bands measured on three of Saturn's satellites, Phoebe, Iaperus, and Hyperion. These bands, measured with the Cassini Visible-Infrared Mapping Spectrometer on close fly-by's of these satellites, are the C-H stretching modes of aromatic hydrocarbons at approximately 3.28 micrometers (approximately 3050 per centimeter), and the are four blended bands of aliphatic -CH2- and -CH3 in the range approximately 3.36-3.52 micrometers (approximately 2980- 2840 per centimeter) bably indicating the presence of polycyclic aromatic hydrocarbons (PAH), is unusually strong in comparison to the aliphatic bands, resulting in a unique signarure among Solar System bodies measured so far, and as such offers a means of comparison among the three satellites. The ratio of the C-H bands in aromatic molecules to those in aliphatic molecules in the surface materials of Phoebe, NAro:NAliph approximately 24; for Hyperion the value is approximately 12, while laperus shows an intermediate value. In view of the trend of the evolution (dehydrogenation by heat and radiation) of aliphatic complexes toward more compact molecules and eventually to aromatics, the relative abundances of aliphatic -CH2- and -CH3- is an indication of the lengths of the molecular chain structures, hence the degree of modification of the original material. We derive CH2:CH3 approximately 2.2 in the spectrum of low-albedo material on laperus; this value is the same within measurement errors to the ratio in the diffuse interstellar medium. The similarity in the spectral signatures of the three satellites, plus the apparent weak trend of aromatic/aliphatic abundance from Phoebe to Hyperion, is consistent with, and effectively confirms that the source of the hydrocarbon-bearing material is Phoebe, and that the appearance of that material on the other two satellites arises from the deposition of the inward-spiraling dust that populates the Phoebe ring.

  20. Shape memory polymers based on uniform aliphatic urethane networks

    SciTech Connect

    Wilson, T S; Bearinger, J P; Herberg, J L; Marion III, J E; Wright, W J; Evans, C L; Maitland, D J

    2007-01-19

    Aliphatic urethane polymers have been synthesized and characterized, using monomers with high molecular symmetry, in order to form amorphous networks with very uniform supermolecular structures which can be used as photo-thermally actuable shape memory polymers (SMPs). The monomers used include hexamethylene diisocyanate (HDI), trimethylhexamethylenediamine (TMHDI), N,N,N{prime},N{prime}-tetrakis(hydroxypropyl)ethylenediamine (HPED), triethanolamine (TEA), and 1,3-butanediol (BD). The new polymers were characterized by solvent extraction, NMR, XPS, UV/VIS, DSC, DMTA, and tensile testing. The resulting polymers were found to be single phase amorphous networks with very high gel fraction, excellent optical clarity, and extremely sharp single glass transitions in the range of 34 to 153 C. Thermomechanical testing of these materials confirms their excellent shape memory behavior, high recovery force, and low mechanical hysteresis (especially on multiple cycles), effectively behaving as ideal elastomers above T{sub g}. We believe these materials represent a new and potentially important class of SMPs, and should be especially useful in applications such as biomedical microdevices.

  1. Exploring mild enzymatic sustainable routes for the synthesis of bio-degradable aromatic-aliphatic oligoesters.

    PubMed

    Pellis, Alessandro; Guarneri, Alice; Brandauer, Martin; Acero, Enrique Herrero; Peerlings, Henricus; Gardossi, Lucia; Guebitz, Georg M

    2016-05-01

    The application of Candida antarctica lipase B in enzyme-catalyzed synthesis of aromatic-aliphatic oligoesters is here reported. The aim of the present study is to systematically investigate the most favorable conditions for the enzyme catalyzed synthesis of aromatic-aliphatic oligomers using commercially available monomers. Reaction conditions and enzyme selectivity for polymerization of various commercially available monomers were considered using different inactivated/activated aromatic monomers combined with linear polyols ranging from C2 to C12 . The effect of various reaction solvents in enzymatic polymerization was assessed and toluene allowed to achieve the highest conversions for the reaction of dimethyl isophthalate with 1,4-butanediol and with 1,10-decanediol (88 and 87% monomer conversion respectively). Mw as high as 1512 Da was obtained from the reaction of dimethyl isophthalate with 1,10-decanediol. The obtained oligomers have potential applications as raw materials in personal and home care formulations, for the production of aliphatic-aromatic block co-polymers or can be further functionalized with various moieties for a subsequent photo- or radical polymerization. PMID:26762794

  2. Mixed aromatic-aliphatic organic nanoparticles as carriers of unidentified infrared emission features

    NASA Astrophysics Data System (ADS)

    Kwok, Sun; Zhang, Yong

    2011-11-01

    Unidentified infrared emission bands at wavelengths of 3-20 micrometres are widely observed in a range of environments in our Galaxy and in others. Some features have been identified as the stretching and bending modes of aromatic compounds, and are commonly attributed to polycyclic aromatic hydrocarbon molecules. The central argument supporting this attribution is that single-photon excitation of the molecule can account for the unidentified infrared emission features observed in `cirrus' clouds in the diffuse interstellar medium. Of the more than 160 molecules identified in the circumstellar and interstellar environments, however, not one is a polycyclic aromatic hydrocarbon molecule. The detections of discrete and broad aliphatic spectral features suggest that the carrier of the unidentified infrared emission features cannot be a pure aromatic compound. Here we report an analysis of archival spectroscopic observations and demonstrate that the data are most consistent with the carriers being amorphous organic solids with a mixed aromatic-aliphatic structure. This structure is similar to that of the organic materials found in meteorites, as would be expected if the Solar System had inherited these organic materials from interstellar sources.

  3. Mixed aromatic-aliphatic organic nanoparticles as carriers of unidentified infrared emission features.

    PubMed

    Kwok, Sun; Zhang, Yong

    2011-11-01

    Unidentified infrared emission bands at wavelengths of 3-20 micrometres are widely observed in a range of environments in our Galaxy and in others. Some features have been identified as the stretching and bending modes of aromatic compounds, and are commonly attributed to polycyclic aromatic hydrocarbon molecules. The central argument supporting this attribution is that single-photon excitation of the molecule can account for the unidentified infrared emission features observed in 'cirrus' clouds in the diffuse interstellar medium. Of the more than 160 molecules identified in the circumstellar and interstellar environments, however, not one is a polycyclic aromatic hydrocarbon molecule. The detections of discrete and broad aliphatic spectral features suggest that the carrier of the unidentified infrared emission features cannot be a pure aromatic compound. Here we report an analysis of archival spectroscopic observations and demonstrate that the data are most consistent with the carriers being amorphous organic solids with a mixed aromatic-aliphatic structure. This structure is similar to that of the organic materials found in meteorites, as would be expected if the Solar System had inherited these organic materials from interstellar sources. PMID:22031328

  4. Solvent substitution

    SciTech Connect

    Not Available

    1990-01-01

    The DOE Environmental Restoration and Waste Management Office of Technology Development and the Air Force Engineering and Services Center convened the First Annual International Workshop on Solvent Substitution on December 4--7, 1990. The primary objectives of this joint effort were to share information and ideas among attendees in order to enhance the development and implementation of required new technologies for the elimination of pollutants associated with industrial use of hazardous and toxic solvents; and to aid in accelerating collaborative efforts and technology transfer between government and industry for solvent substitution. There were workshop sessions focusing on Alternative Technologies, Alternative Solvents, Recovery/Recycling, Low VOC Materials and Treatment for Environmentally Safe Disposal. The 35 invited papers presented covered a wide range of solvent substitution activities including: hardware and weapons production and maintenance, paint stripping, coating applications, printed circuit boards, metal cleaning, metal finishing, manufacturing, compliance monitoring and process control monitoring. This publication includes the majority of these presentations. In addition, in order to further facilitate information exchange and technology transfer, the US Air Force and DOE solicited additional papers under a general Call for Papers.'' These papers, which underwent review and final selection by a peer review committee, are also included in this combined Proceedings/Compendium. For those involved in handling, using or managing hazardous and toxic solvents, this document should prove to be a valuable resource, providing the most up-to-date information on current technologies and practices in solvent substitution. Individual papers are abstracted separated.

  5. Multifunctional aliphatic polyester nanofibers for tissue engineering.

    PubMed

    Zhan, Jianan; Singh, Anirudha; Zhang, Zhe; Huang, Ling; Elisseeff, Jennifer H

    2012-01-01

    Electrospun fibers based on aliphatic polyesters, such as poly(ε-caprolactone) (PCL), have been widely used in regenerative medicine and drug delivery applications due to their biocompatibility, low cost and ease of fabrication. However, these aliphatic polyester fibers are hydrophobic in nature, resulting in poor wettability, and they lack functional groups for decorating the scaffold with chemical and biological cues. Current strategies employed to overcome these challenges include coating and blending the fibers with bioactive components or chemically modifying the fibers with plasma treatment and reactants. In the present study, we report on designing multifunctional electrospun nanofibers based on the inclusion complex of PCL-α-cyclodextrin (PCL-α-CD), which provides both structural support and multiple functionalities for further conjugation of bioactive components. This strategy is independent of any chemical modification of the PCL main chain, and electrospinning of PCL-α-CD is as easy as electrospinning PCL. Here, we describe synthesis of the PCL-α-CD electrospun nanofibers, elucidate composition and structure, and demonstrate the utility of functional groups on the fibers by conjugating a fluorescent small molecule and a polymeric-nanobead to the nanofibers. Furthermore, we demonstrate the application of PCL-α-CD nanofibers for promoting osteogenic differentiation of human adipose-derived stem cells (hADSCs), which induced a higher level of expression of osteogenic markers and enhanced production of extracellular matrix (ECM) proteins or molecules compared with control PCL fibers. PMID:23507886

  6. Process for hydrogenation of hydrocarbon tars

    DOEpatents

    Dolbear, Geoffrey E.

    1978-07-18

    Hydrocarbon tars of high asphaltene content such as tars obtained from pyrolysis of coal are dissolved in a solvent formed from the hydrogenation of the coal tars, and the resultant mixture hydrogenated in the presence of a catalyst at a pressure from about 1500 to 5000 psig at a temperature from about 500.degree. F to about the critical temperature of the solvent to form a light hydrocarbon as a solvent for the tars. Hydrogen content is at least three times the amount of hydrogen consumed.

  7. 40 CFR 721.2270 - Aliphatic dicarboxylic acid salt.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Aliphatic dicarboxylic acid salt. 721... Substances § 721.2270 Aliphatic dicarboxylic acid salt. (a) Chemical substance and significant new uses... salt (PMN P-92-1352) is subject to reporting under this section for the significant new uses...

  8. 40 CFR 721.4497 - Aliphatic polyisocyanates (generic name).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Aliphatic polyisocyanates (generic name). 721.4497 Section 721.4497 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Specific Chemical Substances § 721.4497 Aliphatic polyisocyanates (generic name). (a) Chemical...

  9. 40 CFR 721.4497 - Aliphatic polyisocyanates (generic name).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Aliphatic polyisocyanates (generic name). 721.4497 Section 721.4497 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Specific Chemical Substances § 721.4497 Aliphatic polyisocyanates (generic name). (a) Chemical...

  10. 40 CFR 721.4497 - Aliphatic polyisocyanates (generic name).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Aliphatic polyisocyanates (generic name). 721.4497 Section 721.4497 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Specific Chemical Substances § 721.4497 Aliphatic polyisocyanates (generic name). (a) Chemical...

  11. 40 CFR 721.4497 - Aliphatic polyisocyanates (generic name).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Aliphatic polyisocyanates (generic name). 721.4497 Section 721.4497 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Specific Chemical Substances § 721.4497 Aliphatic polyisocyanates (generic name). (a) Chemical...

  12. 40 CFR 721.4497 - Aliphatic polyisocyanates (generic name).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Aliphatic polyisocyanates (generic name). 721.4497 Section 721.4497 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Specific Chemical Substances § 721.4497 Aliphatic polyisocyanates (generic name). (a) Chemical...

  13. Validation of Alternatives to Aliphatic Isocyanate Polyurethanes

    NASA Technical Reports Server (NTRS)

    Curran, Jerome

    2007-01-01

    The National Aeronautics and Space Administration (NASA) Headquarters chartered the Acquisition Pollution Prevention (AP2) Office to coordinate agency activities affecting pollution prevention issues identified during system and component acquisition and sustainment processes. The primary objective of this effort is to demonstrate and validate alternatives to aliphatic isocyanate polyurethane coatings. Successful completion of this project will result in one or more isocyanate-free coating systems qualified for use at Air Force Space Command (AFSPC) and NASA centers participating in this study. The objective of this project is to qualify the candidates under the specifications for the standard system. This project will compare coating performance of the proposed alternatives to existing coating systems or standards.

  14. Polyimide nanofoams from aliphatic polyester based copolymers

    SciTech Connect

    Hedrick, J.L.; Carter, K.R.; Richter, R.; Russell, T.P.

    1996-10-01

    High temperature polymer foams were prepared using microphase separated block copolymers where the major component is thermally stable block and the minor component is thermally labile. Upon thermal treatment, the dispersed minor component undergoes thermolysis leaving pores the size and shape of which are dictated by the initial copolymer morphology. The driving force behind the survey of aliphatic polyesters as possible labile blocks stems from their quantitative degradation into low boiling, polar degradation products via a backbiting process. Block copolymers were prepared using either a monofunctional caprolactone or a valerolactone oligomer and a high T. polyimide. Microphase morphologies were observed in each case. Thermal decomposition of the polyester blocks was accomplished by a thermal treatment at 370{degrees}C for 5 h. Significant density reductions were measured, and the resulting foams showed pore sizes in the 60-70 {Angstrom} range.

  15. Comparative Genomics of the Ubiquitous, Hydrocarbon-degrading Genus Marinobacter

    NASA Astrophysics Data System (ADS)

    Singer, E.; Webb, E.; Edwards, K. J.

    2012-12-01

    The genus Marinobacter is amongst the most ubiquitous in the global oceans and strains have been isolated from a wide variety of marine environments, including offshore oil-well heads, coastal thermal springs, Antarctic sea water, saline soils and associations with diatoms and dinoflagellates. Many strains have been recognized to be important hydrocarbon degraders in various marine habitats presenting sometimes extreme pH or salinity conditions. Analysis of the genome of M. aquaeolei revealed enormous adaptation versatility with an assortment of strategies for carbon and energy acquisition, sensation, and defense. In an effort to elucidate the ecological and biogeochemical significance of the Marinobacters, seven Marinobacter strains from diverse environments were included in a comparative genomics study. Genomes were screened for metabolic and adaptation potential to elucidate the strategies responsible for the omnipresence of the Marinobacter genus and their remedial action potential in hydrocarbon-polluted waters. The core genome predominantly encodes for key genes involved in hydrocarbon degradation, biofilm-relevant processes, including utilization of external DNA, halotolerance, as well as defense mechanisms against heavy metals, antibiotics, and toxins. All Marinobacter strains were observed to degrade a wide spectrum of hydrocarbon species, including aliphatic, polycyclic aromatic as well as acyclic isoprenoid compounds. Various genes predicted to facilitate hydrocarbon degradation, e.g. alkane 1-monooxygenase, appear to have originated from lateral gene transfer as they are located on gene clusters of 10-20% lower GC-content compared to genome averages and are flanked by transposases. Top ortholog hits are found in other hydrocarbon degrading organisms, e.g. Alcanivorax borkumensis. Strategies for hydrocarbon uptake encoded by various Marinobacter strains include cell surface hydrophobicity adaptation via capsular polysaccharide biosynthesis and attachment

  16. 40 CFR Table 4 to Subpart IIIi of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Default Organic HAP Mass Fraction for... Organic HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction values in the... Solvent type Averageorganic HAP mass fraction Typical organic HAP, percent by mass Aliphatic b 0.03...

  17. 40 CFR Table 4 to Subpart Pppp of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Default Organic HAP Mass Fraction for... Organic HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction values in the.... Solvent type Averageorganic HAP mass fraction Typical organic HAP, percent by mass Aliphatic b 0.03...

  18. 40 CFR Table 4 to Subpart Rrrr of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups 1

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 13 2012-07-01 2012-07-01 false Default Organic HAP Mass Fraction for... Organic HAP Mass Fraction for Petroleum Solvent Groups 1 You May Use the Mass Fraction Values in the...: Solvent type Average organic HAP mass fraction Typical organic percent HAP, by mass Aliphatic 2 0.03...

  19. 40 CFR Table 7 to Subpart Kkkk of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 13 2012-07-01 2012-07-01 false Default Organic HAP Mass Fraction for... Organic HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction values in the.... Solvent type Averageorganic HAP mass fraction Typicalorganic HAP, percent by mass Aliphatic b 0.03...

  20. 40 CFR Table 4 to Subpart Rrrr of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups 1

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 13 2013-07-01 2012-07-01 true Default Organic HAP Mass Fraction for... Organic HAP Mass Fraction for Petroleum Solvent Groups 1 You May Use the Mass Fraction Values in the...: Solvent type Average organic HAP mass fraction Typical organic percent HAP, by mass Aliphatic 2 0.03...

  1. 40 CFR Table 7 to Subpart Kkkk of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 13 2013-07-01 2012-07-01 true Default Organic HAP Mass Fraction for... Organic HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction values in the.... Solvent type Averageorganic HAP mass fraction Typicalorganic HAP, percent by mass Aliphatic b 0.03...

  2. 40 CFR Table 4 to Subpart IIIi of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Organic HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction values in the... Solvent type Averageorganic HAP mass fraction Typical organic HAP, percent by mass Aliphatic b 0.03...

  3. 40 CFR Table 4 to Subpart Pppp of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Default Organic HAP Mass Fraction for... Organic HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction values in the.... Solvent type Averageorganic HAP mass fraction Typical organic HAP, percent by mass Aliphatic b 0.03...

  4. Solvent Production

    Technology Transfer Automated Retrieval System (TEKTRAN)

    This article describes production of butanol [acetone-butanol-ethanol, (also called AB or ABE or solvent)] by fermentation using both traditional and current technologies. AB production from agricultural commodities such as corn and molasses was an important historical fermentation. Unfortunately,...

  5. Composites of vinyl polystyrylpyridine/bismaleimide-aliphatic ether copolymers

    NASA Technical Reports Server (NTRS)

    Heimbuch, Alvin H.; Rosser, Robert W.; Hsu, Ming-Ta S.

    1989-01-01

    An aliphatic ether bismaleimide was prepared and coreacted with a polyvinylstyrylpyridine (VPSP) oligomer. Studies showed that a controlled ratio of aliphatic to aromatic units in the polymer backbone improved both processibility and interlaminar shear properties for the carbon-fiber composite system. This modified resin was readily soluble in tetrahydrofuran, allowing for better fiber impregnation and thus enhancing adhesive properties and reproducibility. DSC studies have shown a lower cure temperature for the copolymer than for the neat aliphatic bismaleimide, and a glass transition temperature of 260 C, which is more than adequate for most applications. Limited measurements indicated an improvement in toughness (impact resistance).

  6. Neurological and neurophysiological examinations of workers occupationally exposed to organic solvent mixtures used in the paint and varnish production.

    PubMed

    Indulski, J A; Sińczuk-Walczak, H; Szymczak, M; Wesołowski, W

    1996-01-01

    The aim of this work was to examine the nervous system of workers chronically exposed to mixtures of organic solvent at concentrations within or slightly exceeding the MAC values, used in the manufacture of paints and lacquers. The tests were performed on a group of 175 people, 107 men aged 22-59 (x = 41.25), and 68 women aged 20-55 (x = 38.62). The period of employment was x = 17.34 years and cumulative dose index 16.97 for males; for females, the corresponding values were x = 14.75 and x = 11.42, respectively. The control group included 175 people (107 men and 68 women) not exposed to chemicals matched according to sex, age, and work shift distribution. The neurological examinations included subjective and objective examinations of the nervous system, electroencephalographic (EEG) and visual evoked potential (VEP) evaluations. The assessment of organic solvent exposure was performed according to the method described in PN89/Z-04008/07, and the solvent mixtures were shown to contain xylenes, ethyltoluenes, trimethylbenzenes, propylbenzene, ethylbenzene, toluene, aliphatic hydrocarbons and the components of painter's naphtha. The most frequent complaints among the exposed males included headache, vertigo, concentration difficulties, sleep disorders, sleepiness during the day, increased emotional irritability, mood swings with a tendency to anxiety. The objective neurological examinations did not reveal organic lesions in the central or peripheral nervous systems. Generalised and paroxysmal changes were most common recordings in the abnormal EEG. VEP examinations revealed abnormalities, primarily in the latency of the response evoked. The results of this study suggest that exposures to concentrations within MAC values, or below 1.5 of the MAC values of organic solvents mixtures used in the manufacture of paints and lacquers produce subclinical health effect in the nervous system. PMID:8972166

  7. U. S. EPA’S APPROACH FOR CHLORINATED SOLVENTS

    EPA Science Inventory

    The approach for chlorinated solvents is similar to the approach for petroleum hydrocarbons. However, there are more mechanisms of removal, including reductive dechlorination (biotic or abiotic), dehydrochloroelimination (abiotic), and hydrolysis (biotic or abiotic). As a resul...

  8. 40 CFR 52.1145 - Regulation on organic solvent use.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... evaporation of such solvent into the atmosphere. (g) Emissions of organic materials into the atmosphere..., evaporation, or drying of saturated halogenated hydrocarbons or perchloroethylene. (4) The use of any...

  9. ANAEROBIC AND AEROBIC TREATMENT OF CHLORINATED ALIPHATIC COMPOUNDS

    EPA Science Inventory

    Biological degradation of 12 chlorinated aliphatic compounds (CACs) was assessed in bench-top reactors and in serum bottle tests. Three continuously mixed daily batch-fed reactor systems were evaluated: anaerobic, aerobic, and sequential-anaerobic-aerobic (sequential). Glucose,...

  10. Deuterated polycyclic aromatic hydrocarbons: Revisited

    NASA Astrophysics Data System (ADS)

    Doney, K. D.; Candian, A.; Mori, T.; Onaka, T.; Tielens, A. G. G. M.

    2016-02-01

    Aims: The amount of deuterium locked up in polycyclic aromatic hydrocarbons (PAHs) has to date been an uncertain value. We present a near-infrared (NIR) spectroscopic survey of Hii regions in the Milky Way, Large Magellanic Cloud, and Small Magellanic Cloud obtained with AKARI, which aims to search for features indicative of deuterated PAHs (PAD or Dn-PAH) to better constrain the D/H ratio of PAHs. Methods: Fifty-three Hii regions were observed in the NIR (2.5-5 μm), using the Infrared Camera (IRC) on board the AKARI satellite. Through comparison of the observed spectra with a theoretical model of deuterated PAH vibrational modes, the aromatic and (a)symmetric aliphatic C-D stretch modes were identified. Results: We see emission features between 4.4-4.8 μm, which could be unambiguously attributed to deuterated PAHs in only six of the observed sources, all of which are located in the Milky Way. In all cases, the aromatic C-D stretching feature is weaker than the aliphatic C-D stretching feature, and, in the case of M17b, this feature is not observed at all. Based on the weak or absent PAD features in most of the observed spectra, it is suggested that the mechanism for PAH deuteration in the ISM is uncommon.

  11. Evaluation of antibacterial activity of synthetic aliphatic and aromatic monoacylglycerols.

    PubMed

    Batovska, Daniela; Todorova, Iva; Parushev, Stoyan; Tsvetkova, Iva; Najdenski, Hristo; Ubukata, Makoto

    2008-01-01

    The antibacterial activity of synthetic aliphatic and aromatic monoacylglycerols (MAGs) was studied against two human pathogens: Staphylococcus aureus and Escherichia coli. The active compounds inhibited selectively S. aureus. The most active compounds amongst them were those with medium size aliphatic chain and aromatic MAGs with electron withdrawing substituents at the aryl ring. The introduction of one or two-carbon spacer between the aryl ring and the carboxylic function did not influence antibacterial effectiveness. PMID:19004249

  12. Process for producing peracids from aliphatic hydroxy carboxylic acids

    DOEpatents

    Chum, H.L.; Palasz, P.D.; Ratcliff, M.A.

    1984-12-20

    A process is described for producing peracids from lactic acid-containing solutions derived from biomass processing systems. It consists of adjusting the pH of the solution to about 8 to 9 and removing alkaline residue fractions therefrom to form a solution comprised substantially of lower aliphatic hydroxy acids. The solution is oxidized to produce volatile lower aliphatic aldehydes. The aldehydes are removed as they are generated and converted to peracids.

  13. Process for producing peracids from aliphatic hydroxy carboxylic acids

    DOEpatents

    Chum, Helena L.; Ratcliff, Matthew A.; Palasz, Peter D.

    1986-01-01

    A process for producing peracids from lactic acid-containing solutions derived from biomass processing systems comprising: adjusting the pH of the solution to about 8-9 and removing alkaline residue fractions therefrom to form a solution comprised substantially of lower aliphatic hydroxy acids; oxidizing the solution to produce volatile lower aliphatic aldehydes; removing said aldehydes as they are generated; and converting said aldehydes to peracids.

  14. Atmospheric chemistry of toxic contaminants. 3. Unsaturated aliphatics: Acrolein, acrylonitrile, maleic anhydride

    SciTech Connect

    Grosjean, D. )

    1990-12-01

    Detailed mechanisms are outlined for the chemical reactions that contribute to in-situ formation and atmospheric removal of the unsaturated aliphatic contaminants acrolein, acrylonitrile, and maleic anhydride. In-situ formation of small amounts of acrolein and maleic anhydride may involve the reaction of OH (and O{sub 3}) with 1,3-dienes and the reaction of OH with aromatic hydrocarbons, respectively. There is no known pathway for in-situ formation of acrylonitrile. Rapid removal of acrolein (half-life = less than one day) and of maleic anhydride (half-life = several hours) is expected from their rapid reactions with OH (major), O{sub 3}, and NO{sub 3}. These reactions lead to formaldehyde and glyoxal from acrolein and to dicarbonyls from maleic anhydride. Acrylonitrile is removed at a slower rate (half-life = 2-7 days) by reaction with OH, leading to formaldehyde and formyl cyanide.

  15. Atmospheric chemistry of toxic contaminants 4. Saturated halogenated aliphatics: Methyl bromide, epichlorhydrin, phosgene

    SciTech Connect

    Grosjean, D. )

    1991-01-01

    Mechanisms are outlined for the reactions that contribute to in-situ formation and atmospheric removal of the saturated halogenated aliphatic contaminants methyl bromide, epichlorhydrin, and phosgene. In-situ formation is important only for phosgene and involves the reaction of OH with chloroethenes and other chlorinated hydrocarbons. A ranking of these phosgene precursors is given using data for precursor ambient concentrations and chemical reactivity. The three toxic compounds studied are long-lived in the atmosphere, where removal of phosgene and methyl bromide by chemical reactions is negligibly slow. Epichlorhydrin is removed slowly by reaction with OH, leading to formaldehyde, chloroacetaldehyde, and the chlorinated peroxyacyl nitrate CH{sub 2}ClC(O)OONO{sub 2}.

  16. Neutron Scattering of Aromatic and Aliphatic Liquids

    PubMed Central

    Falkowska, Marta; Bowron, Daniel T.; Manyar, Haresh G.

    2016-01-01

    Abstract Organic solvents, such as cyclohexane, cyclohexene, methylcyclohexane, benzene and toluene, are widely used as both reagents and solvents in industrial processes. Despite the ubiquity of these liquids, the local structures that govern the chemical properties have not been studied extensively. Herein, we report neutron diffraction measurements on liquid cyclohexane, cyclohexene, methylcyclohexane, benzene and toluene at 298 K to obtain a detailed description of the local structure in these compounds. The radial distribution functions of the centres of the molecules, as well as the partial distribution functions for the double bond for cyclohexene and methyl group for methylcyclohexane and toluene have been calculated. Additionally, probability density functions and angular radial distribution functions were extracted to provide a full description of the local structure within the chosen liquids. Structural motifs are discussed and compared for all liquids, referring specifically to the functional group and aromaticity present in the different liquids. PMID:26990367

  17. Neutron Scattering of Aromatic and Aliphatic Liquids.

    PubMed

    Falkowska, Marta; Bowron, Daniel T; Manyar, Haresh G; Hardacre, Christopher; Youngs, Tristan G A

    2016-07-01

    Organic solvents, such as cyclohexane, cyclohexene, methylcyclohexane, benzene and toluene, are widely used as both reagents and solvents in industrial processes. Despite the ubiquity of these liquids, the local structures that govern the chemical properties have not been studied extensively. Herein, we report neutron diffraction measurements on liquid cyclohexane, cyclohexene, methylcyclohexane, benzene and toluene at 298 K to obtain a detailed description of the local structure in these compounds. The radial distribution functions of the centres of the molecules, as well as the partial distribution functions for the double bond for cyclohexene and methyl group for methylcyclohexane and toluene have been calculated. Additionally, probability density functions and angular radial distribution functions were extracted to provide a full description of the local structure within the chosen liquids. Structural motifs are discussed and compared for all liquids, referring specifically to the functional group and aromaticity present in the different liquids. PMID:26990367

  18. Investigation of the toxicokinetics of petroleum hydrocarbon distillates with the earthworm Eisenia andrei.

    PubMed

    Cermak, Janet; Stephenson, Gladys; Birkholz, Detlef; Dixon, D George

    2013-04-01

    The Canada-wide standards for petroleum hydrocarbons in soils regulate petroleum hydrocarbons based on four distillate ranges: F1 (C6-C10), F2 (>C10-C16), F3 (>C16-C34), and F4 (>C34). Previous toxicity tests with earthworms and F2, as well as two subfractions of F3, F3a (>C16-C23) and F3a (>C23-C34), indicate that test durations might not be sufficiently long to reach threshold effect concentrations, likely because of the differing toxicokinetics for each distillate. A study was conducted to determine the toxicokinetics of both aliphatic and aromatic fractions of F2, F3a, and F3b with the earthworm Eisenia andrei. Peak accumulation curves were observed for F2 aliphatics and aromatics and F3a aromatics, likely as a result of changes in exposure concentration over the test duration via loss or a decrease in the bioavailable fraction. Biota-soil accumulation factors were >1 for total F2 aliphatics and aromatics and F3a aromatics as well as for several individual polyaromatic hydrocarbons for each distillate. Aromatics were disproportionately accumulated over aliphatics and were the main contributors to toxicity; therefore, aromatics and aliphatics should be regulated separately. The toxicokinetics were used to interpret previous toxicity data. Higher molecular weight distillates need longer-than-standard test durations to determine toxicity, so toxicity test results from fixed, standard-duration tests are not strictly comparable for these petroleum distillates. PMID:23364619

  19. Upgrading heavy hydrocarbon oils using sodium hypochlorite

    SciTech Connect

    Rankel, L.A.

    1986-07-22

    A process is described for demetallizing a residual hydrocarbon fraction comprising: (a) contacting the hydrocarbon fraction with an aqueous solution of a hypochlorite salt; (b) separating the mixture into an aqueous phase and an oil phase; (c) contacting the oil phase with a deasphalting solvent and (d) obtaining by separation a product comprising a demetallized oil fraction suitable for use as a feedstock for catalytic processing.

  20. DOE solvent handbook information sheet

    SciTech Connect

    Chavez, A.A.

    1992-01-01

    Solvents and cleaners are used in the Department of Defense (DOD) and the Department of Energy-Defense Program (DOE-DP) maintenance facilities for removing wax, grease, oil, carbon, machining fluids, solder fluxes, mold releases, and other contaminants before repairing or electroplating parts. Private industry also uses cleaners and degreasers for surface preparation of various metals. Growing environmental and worker safety concerns have brought attention to these solvents and cleaners, most of which are classified as toxic. Tightening government regulations have already excluded the use of some chemicals, and restrict the use of various halogenated hydrocarbons because of their atmospheric-ozone depleting effects, as well as their cancer-related risks. As a result, a program was established to develop an efficient, easily accessible, electronic solvent utilization handbook. This is being accomplished by: (1) identifying solvents (alternatives) that are not currently restricted by government regulations for use DOE-DP facilities, and private industry, (2) evaluating their cleaning performance, (3) evaluating their corrosivity, (4) evaluating their air emissions, (5) evaluating the possibility of recycling or recovering all or portions of the alternative degreasers, (6) testing substitute solvents compatibility with non-metallic materials, (7) inputting all of the data gathered (including previous biodegradability information) into a database, and (8) developing a methodology for efficient, widespread access to the data base information system.

  1. DOE solvent handbook information sheet

    SciTech Connect

    Chavez, A.A.

    1992-05-01

    Solvents and cleaners are used in the Department of Defense (DOD) and the Department of Energy-Defense Program (DOE-DP) maintenance facilities for removing wax, grease, oil, carbon, machining fluids, solder fluxes, mold releases, and other contaminants before repairing or electroplating parts. Private industry also uses cleaners and degreasers for surface preparation of various metals. Growing environmental and worker safety concerns have brought attention to these solvents and cleaners, most of which are classified as toxic. Tightening government regulations have already excluded the use of some chemicals, and restrict the use of various halogenated hydrocarbons because of their atmospheric-ozone depleting effects, as well as their cancer-related risks. As a result, a program was established to develop an efficient, easily accessible, electronic solvent utilization handbook. This is being accomplished by: (1) identifying solvents (alternatives) that are not currently restricted by government regulations for use DOE-DP facilities, and private industry, (2) evaluating their cleaning performance, (3) evaluating their corrosivity, (4) evaluating their air emissions, (5) evaluating the possibility of recycling or recovering all or portions of the alternative degreasers, (6) testing substitute solvents compatibility with non-metallic materials, (7) inputting all of the data gathered (including previous biodegradability information) into a database, and (8) developing a methodology for efficient, widespread access to the data base information system.

  2. Distribution of aliphatic compounds in bivalve mollusks from Galicia after the Prestige oil spill: spatial and temporal trends.

    PubMed

    Carro, N; Cobas, J; Maneiro, J

    2006-03-01

    The content and distribution of n-alkane (C8-C35) and isoprenoid (pristane and phytane) hydrocarbons were investigated in two species of bivalve mollusk, mussel (Mytilus galloprovincialis) and cockle (Cerastoderma edule), collected at different points of the Galicia littoral zone during the period from December 2002 to February 2003 (after the Prestige oil spill). Samples were analyzed by high-resolution gas chromatography equipped with a flame ionization detector. The highest levels were found in mussels and cockles coming from two estuarine bays, Rías de Arousa and Vigo. Hydrocarbons with carbon chain length > 30 were detected and determined in all samples. The abundance of these hydrocarbons in biota could be interpreted with regard to the feeding and living habits. Chemometric techniques have been employed to analyze data and determine the potential source of hydrocarbon contamination. Differences between mussels and cockles were observed in relation to aliphatic content. According to the data analysis, the main source of hydrocarbon contamination of investigated samples seems to be more related to the intense traffic of vessels in these estuarine bays than to the Prestige oil spill. PMID:16253223

  3. RECOVERY OF METAL VALUES FROM AQUEOUS SOLUTIONS BY SOLVENT EXTRACTION

    DOEpatents

    Moore, R.L.

    1959-09-01

    An organic solvent mixure is described for extracting actinides from aqueous solutions; the solvent mixture consists of from 10 to 25% by volume of tributyl phosphate and the remainder a chlorine-fluorine-substituted saturated hydrocarbon having two carbon atoms in the molecule.

  4. Extraction process and apparatus for hydrocarbon containing ores

    SciTech Connect

    Friedman, R. H.; Eakin, B. E.

    1985-09-03

    There is provided a hydrocarbon extraction process and apparatus for removing hydrocarbons from a hydrocarbon containing ore such as a diatomite ore. The ore is preprocessed to the extent required to produce an extractable ore and subsequently mixed with a carrier to form an ore stream. The carrier may be a nonaqueous solvent and may further comprise a non-porous granular material such as sand. The ore stream is passed in substantially vertical countercurrent flow through a nonaqueous solvent to produce a product-solvent stream and a spent ore stream. The solvent is subsequently separated from the hydrocarbon stream, which may be further upgraded by removal of a heavy portion. This may be accomplished in the presence of a substantial amount of fines.

  5. Novel solvent systems for in situ extraterrestrial sample analysis

    NASA Astrophysics Data System (ADS)

    Court, Richard W.; Baki, Alexander O.; Sims, Mark R.; Cullen, David; Sephton, Mark A.

    2010-09-01

    The life marker chip (LMC) is being designed to test for the chemical signature of life in the soil and rocks of Mars. It will use an antibody array as part of its detection and characterisation system and aims to detect both polar and non-polar molecules at the sub-ppm to tens of ppb level. It is necessary to use a solvent to transfer organic compounds from the Martian samples to the LMC itself, but organic solvents such as dichloromethane or hexane, commonly used to dissolve non-polar molecules, are incompatible with the LMC antibodies. Hence, an aqueous-based solvent capable of dissolving the biomarkers that might exist in the soil or rocks of Mars is required. Solvent extractions of a Martian soil analogue, JSC Mars-1, spiked with a range of standards show that a 20:80 (vol:vol) mixture of methanol and water is incapable of extracting compounds insoluble in water. However, addition of 1.5 mg ml -1 of the surfactant polysorbate 80 produces extraction efficiencies of the aliphatic standards, hexadecane and phytane, equal to 25-30% of those produced by the common organic solvent mixture 93:7 (vol:vol) dichloromethane:methanol. Extraction of squalene and stigmasterol using the polysorbate solution is less efficient but still successful, at 5-10% of the efficiency of 93:7 dichloromethane:methanol. Such aliphatic compounds with occasional functional groups represent the compound classes to which most fossil organic biomarkers belong. The polysorbate solution did not extract the aromatic compounds pyrene and anthracene with great efficiency. A solvent of 20:80 methanol:water with 1.5 mg ml -1 polysorbate 80 is therefore capable of selectively extracting aliphatic biomarkers from Martian samples and transferring them to the antibody sites on the life marker chip.

  6. Investigation of Aromatic/Aliphatic Polyimides as Dispersants for Single Wall Carbon Nanotubes

    NASA Technical Reports Server (NTRS)

    Delozier, Donavon M.; Watson, Kent A.; Smith, Joseph G., Jr.; Clancy, Thomas C.; Connell, John W.

    2006-01-01

    Novel aromatic/aliphatic polyimides were prepared from 2,7-diamino-9,9'- dioctylfluorene (AFDA) and aromatic dianhydrides. Upon investigating the effectiveness of these polyimides for dispersing single wall carbon nanotubes (SWNTs) in solution, three were discovered to disperse SWNTs in N,N-dimethylacetamide (DMAc). Two of these polyimides, one from 3,3',4,4'-oxydiphthalic anhydride (ODPA) and one from symmetric 3,3',4,4'-biphenyltetracarboxylic dianhydride (s-BPDA), were used to prepare nanocomposites. Homogeneous polyimide/SWNT suspensions from both polymers were used in the preparation of films and fibers containing up to 1 wt% SWNTs. The samples were thermally treated to remove residual solvent and the films were characterized for SWNT dispersion by optical and high resolution scanning electron microscopy (HRSEM). Electrical and mechanical properties of the films were also determined. Electrospun fibers were examined by HRSEM to characterize SWNT alignment and orientation.

  7. Process for solvent refining of coal using a denitrogenated and dephenolated solvent

    DOEpatents

    Garg, Diwakar; Givens, Edwin N.; Schweighardt, Frank K.

    1984-01-01

    A process is disclosed for the solvent refining of non-anthracitic coal at elevated temperatures and pressure in a hydrogen atmosphere using a hydrocarbon solvent which before being recycled in the solvent refining process is subjected to chemical treatment to extract substantially all nitrogenous and phenolic constituents from the solvent so as to improve the conversion of coal and the production of oil in the solvent refining process. The solvent refining process can be either thermal or catalytic. The extraction of nitrogenous compounds can be performed by acid contact such as hydrogen chloride or fluoride treatment, while phenolic extraction can be performed by caustic contact or contact with a mixture of silica and alumina.

  8. Hydrocarbon biological markers in Carboniferous coals of different maturities from the Ruhr area (northwest Germany)

    SciTech Connect

    ten Haven, H.L.; Littke, R.; Rullkoetter, J. , Juelich )

    1989-03-01

    A great variety of biological markers has been found in Carboniferous coal samples. Changes in the paleo-depositional environment are reflected by the distribution of bacterial derived hydrocarbons. These biological markers contribute to a significant extent to the aliphatic hydrocarbon fraction of low-maturity coal samples; their absolute contribution to total organic matter has yet not been estimated. Biological markers for gymnosperm were observed, which is in accordance with the phylogenetic evolution of the plant kingdom during the Carboniferous.

  9. Process and apparatus for solvent extraction of oil from oil-containing diatomite ore

    SciTech Connect

    Karnofsky, G. B.

    1980-12-16

    A process for solvent extraction of oil from oil bearing diatomite ore and an apparatus for use therewith, wherein the ore is extracted by countercurrent decantation with a hydrocarbon solvent, solvent is recovered from the extract by multiple effect evaporation followed by stripping, and the spent diatomite is contacted with water to displace a major portion of the solvent therefrom, and solvent is recovered from the aqueous slurry of the spent diatomite by stripping with steam at superatmospheric pressure.

  10. Hydrocarbon geochemistry of cold seeps in the Monterey Bay National Marine Sanctuary

    USGS Publications Warehouse

    Lorenson, T.D.; Kvenvolden, K.A.; Hostettler, F.D.; Rosenbauer, R.J.; Orange, D.L.; Martin, J.B.

    2002-01-01

    Samples from four geographically and tectonically discrete cold seeps named Clam Flat, Clamfield, Horseshoe Scarp South, and Tubeworm City, within the Monterey Bay National Marine Sanctuary were analyzed for their hydrocarbon content. The sediment contains gaseous hydrocarbons and CO2, as well as high molecular weight aliphatic and aromatic hydrocarbons with various combinations of thermogenic and biogenic contributions from petroleum, marine, and terrigenous sources. Of particular interest is the cold seep site at Clamfield which is characterized by the presence of thermogenic hydrocarbons including oil that can likely be correlated with oil-saturated strata at Majors Creek near Davenport, CA, USA. At Clam Flat, the evidence for thermogenic hydrocarbons is equivocal. At Horseshoe Scarp South and Tubeworm City, hydrocarbon gases, mainly methane, are likely microbial in origin. These varied sources of hydrocarbon gases highlight the diverse chemical systems that appear at cold seep communities. ?? 2002 Elsevier Science B.V. All rights reserved.

  11. Composition and sources of aliphatic lipids and sterols in sediments of a tropical island, southern South China Sea: preliminary assessment.

    PubMed

    Mohd Tahir, N; Pang, S Y; Abdullah, N A; Suratman, S

    2013-12-01

    Near-shore surface sediment was collected from five stations off Redang Island located on the eastern coast of Peninsular Malaysia. Freeze-dried sediments were Soxhlet extracted and then fractionated using column chromatography into aliphatic and polar fractions. Determination of these fractions was carried out using gas chromatography mass spectrometry. The concentration of total resolved aliphatic hydrocarbons in sediments ranged from 157 to 308 ng/g. The distribution of aliphatic fraction showed the presence of n-alkanes ranging from nC15 to nC33 with a minor odd-to-even predominance exhibiting carbon maximum, depending on station, at nC17, nC26, nC29 or nC31. Calculation of Carbon Preference Index (CPI) for CPI(15-33) gave values ranging from 1.09 to 1.46. n-Alkanol in all sediment exhibits even-to-odd carbon predominance ranging from nC16 to nC28 and maximising at nC22. n-Fatty acids distribution ranged from nC14 to nC24 with a dominant maximum at nC16 and exhibiting high values of short chain fatty acids (≤nC20) to long chain fatty acids (>nC20) ratios. Unsaturated fatty acids, particularly nC16:1 and nC18:1 is also ubiquitous in all samples. Cholesterol is the most abundant compound amongst the sterol group ranging from 42.8 to 62.6% of the total sterols. β-Sitosterol, brassicasterol and stigmasterol, are also present but of relatively lower amount. These observations suggest that the aliphatic lipids and sterols in the study area originate, mainly, from biogenic sources of marine microbial with minor contribution from epiticular waxes of terrestrial plants. PMID:23856812

  12. MCU MATERIALS COMPATIBILITY WITH CSSX SOLVENT

    SciTech Connect

    Fondeur, F

    2006-01-13

    The Modular Caustic-Side Solvent Extraction (CSSX) Unit (MCU) plans to use several new materials of construction not previously used with CSSX solvent. SRNL researchers tested seven materials proposed for service in seal and gasket applications. None of the materials leached detectable amounts of components into the CSSX solvent during 96 hour tests. All are judged acceptable for use based on their effect on the solvent. However, some of the materials adsorbed solvent or changed dimensions during contact with solvent. Consultation with component and material vendors with regard to performance impact and in-use testing of the materials is recommended. Polyetheretherketone (PEEK), a material selected for use in contactor bearing seals, did not gain weight or change dimensions on contact with CSSX solvent. Analysis of the solvent contacted with this material showed no impurities and the standard dispersion test gave acceptable phase separation results. The material contains a leachable hydrocarbon substance, detectable on exposed surfaces, that did not adversely contaminate the solvent within the limits of the testing. We recommend contacting the vendor to determine the source and purpose of this component, or, alternatively, pursue the infrared analysis of the PEEK in an effort to better define potential impacts.

  13. Acceleration of Nucelophilic CH Activation by Strongly Basic Solvents

    SciTech Connect

    Hashiguchi, Brian G; Young, Kenneth J. H.; Yousufuddin, Muhammed; Goddard, William A; Periana, Roy A

    2010-09-15

    (IPI)Ru(II)(OH){sub n}(H{sub 2}O){sub m}, 2, where IPI is the NNN-pincer ligand, 2,6-diimidizoylpyridine, is shown to catalyze H/D exchange between hydrocarbons and strongly basic solvents at higher rates than in the case of the solvent alone. Significantly, catalysis by 2 is accelerated rather than inhibited by increasing solvent basicity. The evidence is consistent with the reaction proceeding by base modulated nucleophilic CH activation.

  14. Carbon-rich dust past the asymptotic giant branch: Aliphatics, aromatics, and fullerenes in the Magellanic Clouds

    SciTech Connect

    Sloan, G. C.; Lagadec, E.; Zijlstra, A. A.; Kraemer, K. E.; Weis, A. P.; Matsuura, M.; Volk, K.; Peeters, E.; Cami, J.; Duley, W. W.; Bernard-Salas, J.; Kemper, F.

    2014-08-10

    Infrared spectra of carbon-rich objects that have evolved off the asymptotic giant branch reveal a range of dust properties, including fullerenes, polycyclic aromatic hydrocarbons (PAHs), aliphatic hydrocarbons, and several unidentified features, including the 21 μm emission feature. To test for the presence of fullerenes, we used the position and width of the feature at 18.7-18.9 μm and examined other features at 17.4 and 6-9 μm. This method adds three new fullerene sources to the known sample, but it also calls into question three previous identifications. We confirm that the strong 11 μm features seen in some sources arise primarily from SiC, which may exist as a coating around carbonaceous cores and result from photo-processing. Spectra showing the 21 μm feature usually show the newly defined Class D PAH profile at 7-9 μm. These spectra exhibit unusual PAH profiles at 11-14 μm, with weak contributions at 12.7 μm, which we define as Class D1, or show features shifted to ∼11.4, 12.4, and 13.2 μm, which we define as Class D2. Alkyne hydrocarbons match the 15.8 μm feature associated with 21 μm emission. Sources showing fullerene emission but no PAHs have blue colors in the optical, suggesting a clear line of sight to the central source. Spectra with 21 μm features and Class D2 PAH emission also show photometric evidence for a relatively clear line of sight to the central source. The multiple associations of the 21 μm feature with aliphatic hydrocarbons suggest that the carrier is related to this material in some way.

  15. Carbon-rich Dust Past the Asymptotic Giant Branch: Aliphatics, Aromatics, and Fullerenes in the Magellanic Clouds

    NASA Astrophysics Data System (ADS)

    Sloan, G. C.; Lagadec, E.; Zijlstra, A. A.; Kraemer, K. E.; Weis, A. P.; Matsuura, M.; Volk, K.; Peeters, E.; Duley, W. W.; Cami, J.; Bernard-Salas, J.; Kemper, F.; Sahai, R.

    2014-08-01

    Infrared spectra of carbon-rich objects that have evolved off the asymptotic giant branch reveal a range of dust properties, including fullerenes, polycyclic aromatic hydrocarbons (PAHs), aliphatic hydrocarbons, and several unidentified features, including the 21 μm emission feature. To test for the presence of fullerenes, we used the position and width of the feature at 18.7-18.9 μm and examined other features at 17.4 and 6-9 μm. This method adds three new fullerene sources to the known sample, but it also calls into question three previous identifications. We confirm that the strong 11 μm features seen in some sources arise primarily from SiC, which may exist as a coating around carbonaceous cores and result from photo-processing. Spectra showing the 21 μm feature usually show the newly defined Class D PAH profile at 7-9 μm. These spectra exhibit unusual PAH profiles at 11-14 μm, with weak contributions at 12.7 μm, which we define as Class D1, or show features shifted to ~11.4, 12.4, and 13.2 μm, which we define as Class D2. Alkyne hydrocarbons match the 15.8 μm feature associated with 21 μm emission. Sources showing fullerene emission but no PAHs have blue colors in the optical, suggesting a clear line of sight to the central source. Spectra with 21 μm features and Class D2 PAH emission also show photometric evidence for a relatively clear line of sight to the central source. The multiple associations of the 21 μm feature with aliphatic hydrocarbons suggest that the carrier is related to this material in some way.

  16. Compounds in airborne particulates - Salts and hydrocarbons. [at Cleveland, OH

    NASA Technical Reports Server (NTRS)

    King, R. B.; Antoine, A. C.; Fordyce, J. S.; Neustadter, H. E.; Leibecki, H. F.

    1977-01-01

    Concentrations of 10 polycyclic aromatic hydrocarbons (PAH), the aliphatics as a group, sulfate, nitrate, fluoride, acidity, and carbon in the airborne particulate matter were measured at 16 sites in Cleveland, OH over a 1-year period during 1971 and 1972. Analytical methods used included gas chromatography, colorimetry, and combustion techniques. Uncertainties in the concentrations associated with the sampling procedures, and the analytical methods are evaluated. The data are discussed relative to other studies and source origins. High concentrations downwind of coke ovens for 3,4 benzopyrene are discussed. Hydrocarbon correlation studies indicated no significant relations among compounds studied.

  17. Differential effects of indole and aliphatic glucosinolates on lepidopteran herbivores.

    PubMed

    Müller, René; de Vos, Martin; Sun, Joel Y; Sønderby, Ida E; Halkier, Barbara A; Wittstock, Ute; Jander, Georg

    2010-08-01

    Glucosinolates are a diverse group of defensive secondary metabolites that is characteristic of the Brassicales. Arabidopsis thaliana (L.) Heynh. (Brassicaceae) lines with mutations that greatly reduce abundance of indole glucosinolates (cyp79B2 cyp79B3), aliphatic glucosinolates (myb28 myb29), or both (cyp79B2 cyp79B3 myb28 myb29) make it possible to test the in vivo defensive function of these two major glucosinolate classes. In experiments with Lepidoptera that are not crucifer-feeding specialists, aliphatic and indole glucosinolates had an additive effect on Spodoptera exigua (Hübner) (Lepidoptera: Noctuidae) larval growth, whereas Trichoplusia ni (Hübner) (Lepidoptera: Noctuidae) and Manduca sexta (L.) (Lepidoptera: Sphingidae) were affected only by the absence of aliphatic glucosinolates. In the case of two crucifer-feeding specialists, Pieris rapae (L.) (Lepidoptera: Pieridae) and Plutella xylostella (L.) (Lepidoptera: Plutellidae), there were no major changes in larval performance due to decreased aliphatic and/or indole glucosinolate content. Nevertheless, choice tests show that aliphatic and indole glucosinolates act in an additive manner to promote larval feeding of both species and P. rapae oviposition. Together, these results support the hypothesis that a diversity of glucosinolates is required to limit the growth of multiple insect herbivores. PMID:20617455

  18. Hydrous pyrolysis/oxidation process for in situ destruction of chlorinated hydrocarbon and fuel hydrocarbon contaminants in water and soil

    DOEpatents

    Knauss, Kevin G.; Copenhaver, Sally C.; Aines, Roger D.

    2000-01-01

    In situ hydrous pyrolysis/oxidation process is useful for in situ degradation of hydrocarbon water and soil contaminants. Fuel hydrocarbons, chlorinated hydrocarbons, polycyclic aromatic hydrocarbons, petroleum distillates and other organic contaminants present in the soil and water are degraded by the process involving hydrous pyrolysis/oxidation into non-toxic products of the degradation. The process uses heat which is distributed through soils and water, optionally combined with oxygen and/or hydrocarbon degradation catalysts, and is particularly useful for remediation of solvent, fuel or other industrially contaminated sites.

  19. THE STRUCTURE, ORIGIN, AND EVOLUTION OF INTERSTELLAR HYDROCARBON GRAINS

    SciTech Connect

    Chiar, J. E.; Ricca, A.; Tielens, A. G. G. M.; Adamson, A. J. E-mail: Alessandra.Ricca@1.nasa.gov E-mail: aadamson@gemini.edu

    2013-06-10

    Many materials have been considered for the carrier of the hydrocarbon absorption bands observed in the diffuse interstellar medium (ISM). In order to refine the model for ISM hydrocarbon grains, we analyze the observed aromatic (3.28, 6.2 {mu}m) and aliphatic (3.4 {mu}m) hydrocarbon absorption features in the diffuse ISM along the line of sight toward the Galactic center Quintuplet Cluster. Observationally, sp {sup 2} bonds can be measured in astronomical spectra using the 6.2 {mu}m CC aromatic stretch feature, whereas the 3.4 {mu}m aliphatic feature can be used to quantify the fraction of sp {sup 3} bonds. The fractional abundance of these components allows us to place the Galactic diffuse ISM hydrocarbons on a ternary phase diagram. We conclude that the Galactic hydrocarbon dust has, on average, a low H/C ratio and sp {sup 3} content and is highly aromatic. We have placed the results of our analysis within the context of the evolution of carbon dust in the ISM. We argue that interstellar carbon dust consists of a large core of aromatic carbon surrounded by a thin mantle of hydrogenated amorphous carbon (a-C:H), a structure that is a natural consequence of the processing of stardust grains in the ISM.

  20. Hot-solvent miscible displacement

    SciTech Connect

    Awang, M.; Farouq Ali, S.M.

    1980-01-01

    This work describes an experimental and theoretical investigation of miscible displacement under nonisothermal conditions. The hot miscible floods were performed in an adiabatic glass bead pack, displacing one hydrocarbon by a more viscous hydrocarbon, the latter being at an elevated temperature. As a result, dispersion of both mass and heat took place, and was determined by temperature and concentration measurements. The system was simulated by coupled convective-diffusion and thermal conduction-convection equations. The results of the numerical as well as an approximate analytical solution were compared with the experimentally observed behavior. The numerical and experimental results point to the factors which should be considered in the choice of a solvent for a thermal-miscible type oil recovery process.

  1. Complete genome sequence of Sphingorhabdus sp. M41, a versatile hydrocarbon degrader, isolated from crude oil-contaminated costal sediment.

    PubMed

    Jeong, Hye Im; Jin, Hyun Mi; Jeon, Che Ok

    2016-06-10

    Sphingorhabdus sp. M41, capable of degrading aliphatic and aromatic hydrocarbons, was isolated from crude oil-contaminated costal sediment by an enrichment culture and its complete genome was sequenced. The genome of strain M41 has a chromosome with a size of 3,324,420bp, including 44 tRNAs, 6 rRNAs, and 3118 protein-coding genes. In addition, many potential genes responsible for the biodegradation of aliphatic and aromatic hydrocarbons were identified from the genome. This is the first complete genome of the genus Sphingorhabdus, which will provide insights into the bioremediation of crude oil-contaminated costal sediment by strain M41. PMID:27080446

  2. Apparatus for hydrocarbon extraction

    DOEpatents

    Bohnert, George W.; Verhulst, Galen G.

    2013-03-19

    Systems and methods for hydrocarbon extraction from hydrocarbon-containing material. Such systems and methods relate to extracting hydrocarbon from hydrocarbon-containing material employing a non-aqueous extractant. Additionally, such systems and methods relate to recovering and reusing non-aqueous extractant employed for extracting hydrocarbon from hydrocarbon-containing material.

  3. Tailor-made design of J- or H-aggregated naphthalenediimide-based gels and remarkable fluorescence turn on/off behaviour depending on solvents.

    PubMed

    Basak, Shibaji; Nandi, Nibedita; Baral, Abhishek; Banerjee, Arindam

    2015-01-14

    A naphthalenediimide (NDI)-based new gelator molecule has been discovered, the molecule forms interesting J/H-aggregated species depending on solvents (aliphatic/aromatic) and remarkably, the fluorescence of the gel phase materials is nicely tuned according to the electron donating capacity of the aromatic solvent. PMID:25426500

  4. Selective thermal and photooxidation of hydrocarbons in zeolites by oxygen

    DOEpatents

    Frei, Heinz; Blatter, Fritz; Sun, Hai

    2001-01-01

    A process for a combined selective thermal oxidation and photooxidation of hydrocarbons adsorbed onto zeolite matrices. A highly combined selective thermal oxidation and photooxidation of unsubstituted or alkyl substituted alkanes, alkenes, aromatics and cycloalkyls in solvent free zeolites under dark thermal conditions or under irradiation with visible light. The process oxidizes hydrocarbons almost completely selectively without substantial production of byproducts.

  5. Selective thermal and photooxidation of hydrocarbons in zeolites by oxygen

    DOEpatents

    Frei, Heinz; Blatter, Fritz; Sun, Hai

    1999-01-01

    A process for selective thermal oxidation or photooxidation of hydrocarbons adsorbed onto zeolite matrices. A highly selective thermal oxidation and photooxidation of unsubstituted or alkyl substituted alkanes, alkenes, aromatics and cycloalkyls in solvent free zeolites under dark thermal conditions or under irradiation with visible light. The process oxidizes hydrocarbons almost completely selectively without substantial production of byproducts.

  6. Selective thermal and photooxidation of hydrocarbons in zeolites by oxygen

    DOEpatents

    Frei, H.; Blatter, F.; Sun, H.

    1999-06-22

    A process is described for selective thermal oxidation or photooxidation of hydrocarbons adsorbed onto zeolite matrices. A highly selective thermal oxidation and photooxidation of unsubstituted or alkyl substituted alkanes, alkenes, aromatics and cycloalkyls in solvent free zeolites under dark thermal conditions or under irradiation with visible light. The process oxidizes hydrocarbons almost completely selectively without substantial production of byproducts. 19 figs.

  7. Selective thermal oxidation of hydrocarbons in zeolites by oxygen

    DOEpatents

    Frei, Heinz; Blatter, Fritz; Sun, Hai

    2000-01-01

    A process for selective thermal oxidation of hydrocarbons adsorbed onto zeolite matrices. A highly selective thermal oxidation of unsubstituted or alkyl substituted alkanes, alkenes, aromatics and cycloalkyls is carried out in solvent free zeolites under dark thermal conditions. The process oxidizes hydrocarbons almost completely selectively without substantial production of byproducts.

  8. Liquid ammonia as a dipolar aprotic solvent for aliphatic nucleophilic substitution reactions.

    PubMed

    Ji, Pengju; Atherton, John; Page, Michael I

    2011-03-01

    The rate constants for the reactions of a variety of nucleophiles reacting with substituted benzyl chlorides in liquid ammonia (LNH(3)) have been determined. To fully interpret the associated linear free-energy relationships, the ionization constants of phenols ions in liquid ammonia were obtained using UV spectra. These equilibrium constants are the product of those for ion-pair formation and dissociation to the free ions, which can be separated by evaluating the effect of added ammonium ions. There is a linear relationship between the pK(a) of phenols in liquid ammonia and those in water of slope 1.68. Aminium ions exist in their unprotonated free base form in liquid ammonia and their ionization constants could not be determined by NMR. The rates of solvolysis of substituted benzyl chlorides in liquid ammonia at 25 °C show a Hammett ρ of zero, having little or no dependence upon ring substituents, which is in stark contrast with the hydrolysis rates of substituted benzyl halides in water, which vary 10(7) fold. The rate of substitution of benzyl chloride by substituted phenoxide ions is first order in the concentration of the nucleophile indicative of a S(N)2 process, and the dependence of the rate constants on the pK(a) of the phenol in liquid ammonia generates a Brønsted β(nuc) = 0.40. Contrary to the solvolysis reaction, the reaction of phenoxide ion with 4-substituted benzyl chlorides gives a Hammett ρ = 1.1, excluding the 4-methoxy derivative, which shows the normal positive deviation. The second order rate constants for the substitution of benzyl chlorides by neutral and anionic amines show a single Brønsted β(nuc) = 0.21 (based on the aqueous pK(a) of amine), but their dependence on the substituent in substituted benzyl chlorides varies with a Hammett ρ of 0 for neutral amines, similar to that seen for solvolysis, whereas that for amine anions is 0.93, similar to that seen for phenoxide ion. PMID:21348532

  9. Catalytic Asymmetric Hydroamination of Unactivated Internal Olefins to Aliphatic Amines

    PubMed Central

    Yang, Yang; Shi, Shi-Liang; Niu, Dawen; Liu, Peng; Buchwald, Stephen L.

    2015-01-01

    Catalytic assembly of enantiopure aliphatic amines from abundant and readily available precursors has long been recognized as a paramount challenge in synthetic chemistry. Herein, we describe a mild and general copper-catalyzed hydroamination that effectively converts unactivated internal olefins, an important yet unexploited class of abundant feedstock chemicals, into highly enantioenriched α-branched amines (≥ 96% enantiomeric excess) featuring two minimally differentiated aliphatic substituents. This method provides a powerful means to access a broad range of advanced, highly functionalized enantioenriched amines of interest in pharmaceutical research and other areas. PMID:26138973

  10. Volatile hydrocarbons inhibit methanogenic crude oil degradation

    PubMed Central

    Sherry, Angela; Grant, Russell J.; Aitken, Carolyn M.; Jones, D. Martin; Head, Ian M.; Gray, Neil D.

    2014-01-01

    Methanogenic degradation of crude oil in subsurface sediments occurs slowly, but without the need for exogenous electron acceptors, is sustained for long periods and has enormous economic and environmental consequences. Here we show that volatile hydrocarbons are inhibitory to methanogenic oil biodegradation by comparing degradation of an artificially weathered crude oil with volatile hydrocarbons removed, with the same oil that was not weathered. Volatile hydrocarbons (nC5–nC10, methylcyclohexane, benzene, toluene, and xylenes) were quantified in the headspace of microcosms. Aliphatic (n-alkanes nC12–nC34) and aromatic hydrocarbons (4-methylbiphenyl, 3-methylbiphenyl, 2-methylnaphthalene, 1-methylnaphthalene) were quantified in the total hydrocarbon fraction extracted from the microcosms. 16S rRNA genes from key microorganisms known to play an important role in methanogenic alkane degradation (Smithella and Methanomicrobiales) were quantified by quantitative PCR. Methane production from degradation of weathered oil in microcosms was rapid (1.1 ± 0.1 μmol CH4/g sediment/day) with stoichiometric yields consistent with degradation of heavier n-alkanes (nC12–nC34). For non-weathered oil, degradation rates in microcosms were significantly lower (0.4 ± 0.3 μmol CH4/g sediment/day). This indicated that volatile hydrocarbons present in the non-weathered oil inhibit, but do not completely halt, methanogenic alkane biodegradation. These findings are significant with respect to rates of biodegradation of crude oils with abundant volatile hydrocarbons in anoxic, sulphate-depleted subsurface environments, such as contaminated marine sediments which have been entrained below the sulfate-reduction zone, as well as crude oil biodegradation in petroleum reservoirs and contaminated aquifers. PMID:24765087

  11. Azeotropic distillation process for recovery of diamondoid compounds from hydrocarbon streams

    SciTech Connect

    Alexander, R.A.; Whitehurst, D.D.

    1992-08-18

    This patent describes a method for separating a diamondoid compound selected from the group consisting of adamantane, diamantane, triamantane and the alkyl substituted homologs of adamantane, diamantane, and triamantane from a hydrocarbon compound. This patent also describes a method for extracting diamondoid compounds from a hydrocarbon gas containing the same. It comprises providing a hydrocarbon gas stream containing a recoverable concentration of at least one concentration of at least one diamondoid compound; contacting the hydrocarbon gas stream with a liquid hydrocarbon solvent in which the diamondoid compound is at least partially soluble to dissolve the diamondoid compound in the liquid hydrocarbon solvent; and distilling the diamondoid-containing hydrocarbon solvent of step in the presence of water sufficient to cause an azeotrope with the diamondoid compound.

  12. Aquifer washing by micellar solutions: 1. Optimization of alcohol-surfactant-solvent solutions

    NASA Astrophysics Data System (ADS)

    Martel, Richard; Gélinas, Pierre J.; Desnoyers, Jacques E.

    1998-03-01

    Phase diagrams were used for the formulation of alcohol-surfactant-solvent and to identify the DNAPL (Dense Non Aqueous Phase Liquid) extraction zones. Four potential extraction zones of Mercier DNAPL, a mixture of heavy aliphatics, aromatics and chlorinated hydrocarbons, were identified but only one microemulsion zone showed satisfactory DNAPL recovery in sand columns. More than 90 sand column experiments were performed and demonstrate that: (1) neither surfactant in water, alcohol-surfactant solutions, nor pure solvent can effectively recover Mercier DNAPL and that only alcohol-surfactant-solvent solutions are efficient; (2) adding salts to alcohol-surfactant or to alcohol-surfactant-solvent solutions does not have a beneficial effect on DNAPL recovery; (3) washing solution formulations are site specific and must be modified if the surface properties of the solids (mineralogy) change locally, or if the interfacial behavior of liquids (type of oil) changes; (4) high solvent concentrations in washing solutions increase DNAPL extraction but also increase their cost and decrease their density dramatically; (5) maximum DNAPL recovery is observed with alcohol-surfactant-solvent formulations which correspond to the maximum solubilization in Zone C of the phase diagram; (6) replacing part of surfactant SAS by the alcohol n-butanol increases washing solution efficiency and decreases the density and the cost of solutions; (7) replacing part of n-butanol by the nonionic surfactant HOES decreases DNAPL recovery and increases the cost of solutions; (8) toluene is a better solvent than D-limonene because it increases DNAPL recovery and decreases the cost of solutions; (9) optimal alcohol-surfactant-solvent solutions contain a mixture of solvents in a mass ratio of toluene to D-limonene of one or two. Injection of 1.5 pore volumes of the optimal washing solution of n-butanol-SAS-toluene- D-limonene in water can recover up to 95% of Mercier DNAPL in sand columns. In the first

  13. Applicability of the theory of thermodynamic similarity to predict the enthalpies of vaporization of aliphatic aldehydes

    NASA Astrophysics Data System (ADS)

    Esina, Z. N.; Korchuganova, M. R.

    2015-06-01

    The theory of thermodynamic similarity is used to predict the enthalpies of vaporization of aliphatic aldehydes. The predicted data allow us to calculate the phase diagrams of liquid-vapor equilibrium in a binary water-aliphatic aldehyde system.

  14. Photochemistry of squaraine dyes. 6. Solvent hydrogen bonding effects on the photophysical properties of bis(benzothiazolylidene)squaraines

    SciTech Connect

    Das, S. Regional Research Lab. , Trivandrum ); Thomas, K.G.; Ramanathan, R. , Trivandrum ); George, M.V. Jawaharlal Nehru Centre for Advanced Scientific Research, Bangalore Regional Research Lab. , Trivandrum ); Kamat, P.V. )

    1993-12-23

    The photophysical properties of two bis(benzothiazolylidene)squaraine dyes have been studied in aromatic hydrocarbon and alcoholic solvents. These dyes exhibit fluorescence quantum yields of 0.06-0.52 and excited singlet lifetimes of 0.48-2.5 ns in these solvents. Although the photophysical properties of the dyes are independent of solvent polarity in the hydrocarbon solvents, in alcoholic solvents a marked hyposchromic shift in the absorption and emission spectra and a reduction in lifetimes of excited state have been observed. These effects have been correlated with the hydrogen bond donating ability of the alcoholic solvents. 17 refs., 6 figs., 2 tabs.

  15. Introducing Aliphatic Substitution with a Discovery Experiment Using Competing Electrophiles

    ERIC Educational Resources Information Center

    Curran, Timothy P.; Mostovoy, Amelia J.; Curran, Margaret E.; Berger, Clara

    2016-01-01

    A facile, discovery-based experiment is described that introduces aliphatic substitution in an introductory undergraduate organic chemistry curriculum. Unlike other discovery-based experiments that examine substitution using two competing nucleophiles with a single electrophile, this experiment compares two isomeric, competing electrophiles…

  16. Selective stabilization of aliphatic organic carbon by iron oxide

    PubMed Central

    Adhikari, Dinesh; Yang, Yu

    2015-01-01

    Stabilization of organic matter in soil is important for natural ecosystem to sequestrate carbon and mitigate greenhouse gas emission. It is largely unknown what factors govern the preservation of organic carbon in soil, casting shadow on predicting the response of soil to climate change. Iron oxide was suggested as an important mineral preserving soil organic carbon. However, ferric minerals are subject to reduction, potentially releasing iron and decreasing the stability of iron-bound organic carbon. Information about the stability of iron-bound organic carbon in the redox reaction is limited. Herein, we investigated the sorptive interactions of organic matter with hematite and reductive release of hematite-bound organic matter. Impacts of organic matter composition and conformation on its sorption by hematite and release during the reduction reaction were analyzed. We found that hematite-bound aliphatic carbon was more resistant to reduction release, although hematite preferred to sorb more aromatic carbon. Resistance to reductive release represents a new mechanism that aliphatic soil organic matter was stabilized by association with iron oxide. Selective stabilization of aliphatic over aromatic carbon can greatly contribute to the widely observed accumulation of aliphatic carbon in soil, which cannot be explained by sorptive interactions between minerals and organic matter. PMID:26061259

  17. Triphosgene–Amine Base Promoted Chlorination of Unactivated Aliphatic Alcohols

    PubMed Central

    Villalpando, Andrés; Ayala, Caitlan E.; Watson, Christopher B.; Kartika, Rendy

    2014-01-01

    Unactivated α-branched primary and secondary aliphatic alcohols have been successfully transformed into their corresponding alkyl chlorides in high yields upon treatment with a mixture of triphosgene and pyridine in dichloromethane at reflux. These mild chlorination conditions are high yielding, stereospecific, and well tolerated by numerous sensitive functionalities. Furthermore, no nuisance waste products are generated in the course of the reactions. PMID:23496045

  18. Cloud condensation nuclei activity of aliphatic amine secondary aerosol

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Aliphatic amines can form secondary aerosol via oxidation with atmospheric radicals (e.g. hydroxyl radical and nitrate radical). The resulting particle composition can contain both secondary organic aerosol (SOA) and inorganic salts. The fraction of organic to inorganic materials in the particulate ...

  19. A thermostable transketolase evolved for aliphatic aldehyde acceptors.

    PubMed

    Yi, Dong; Saravanan, Thangavelu; Devamani, Titu; Charmantray, Franck; Hecquet, Laurence; Fessner, Wolf-Dieter

    2015-01-11

    Directed evolution of the thermostable transketolase from Geobacillus stearothermophilus based on a pH-based colorimetric screening of smart libraries yielded several mutants with up to 16-fold higher activity for aliphatic aldehydes and high enantioselectivity (>95% ee) in the asymmetric carboligation step. PMID:25415647

  20. 40 CFR 721.10199 - Substituted aliphatic amine (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... should be tested and approved for the gas/vapor substance (i.e., organic vapor, acid gas, or substance... combination cartridges, cartridges should be tested and approved for the gas/vapor substance (i.e., organic... Specific Chemical Substances § 721.10199 Substituted aliphatic amine (generic). (a) Chemical substance...

  1. 40 CFR 721.10199 - Substituted aliphatic amine (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... should be tested and approved for the gas/vapor substance (i.e., organic vapor, acid gas, or substance... combination cartridges, cartridges should be tested and approved for the gas/vapor substance (i.e., organic... Specific Chemical Substances § 721.10199 Substituted aliphatic amine (generic). (a) Chemical substance...

  2. 40 CFR 721.10199 - Substituted aliphatic amine (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... should be tested and approved for the gas/vapor substance (i.e., organic vapor, acid gas, or substance... combination cartridges, cartridges should be tested and approved for the gas/vapor substance (i.e., organic... Specific Chemical Substances § 721.10199 Substituted aliphatic amine (generic). (a) Chemical substance...

  3. 40 CFR 721.10199 - Substituted aliphatic amine (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... should be tested and approved for the gas/vapor substance (i.e., organic vapor, acid gas, or substance... combination cartridges, cartridges should be tested and approved for the gas/vapor substance (i.e., organic... Specific Chemical Substances § 721.10199 Substituted aliphatic amine (generic). (a) Chemical substance...

  4. 40 CFR 721.10608 - Aliphatic diisocyanate polymer with alkanediol and alkylglycol (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Aliphatic diisocyanate polymer with... Significant New Uses for Specific Chemical Substances § 721.10608 Aliphatic diisocyanate polymer with.... (1) The chemical substance identified generically as aliphatic diisocyanate polymer with...

  5. 40 CFR 721.10608 - Aliphatic diisocyanate polymer with alkanediol and alkylglycol (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Aliphatic diisocyanate polymer with... Significant New Uses for Specific Chemical Substances § 721.10608 Aliphatic diisocyanate polymer with.... (1) The chemical substance identified generically as aliphatic diisocyanate polymer with...

  6. 40 CFR 721.10289 - Hexanedioic acid polymer with aliphatic polyol dihydrogen phosphate aromatic ester (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... aliphatic polyol dihydrogen phosphate aromatic ester (generic). 721.10289 Section 721.10289 Protection of... polymer with aliphatic polyol dihydrogen phosphate aromatic ester (generic). (a) Chemical substance and... acid polymer with aliphatic polyol dihydrogen phosphate aromatic ester (PMN P-11-333) is subject...

  7. 40 CFR 721.10289 - Hexanedioic acid polymer with aliphatic polyol dihydrogen phosphate aromatic ester (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... aliphatic polyol dihydrogen phosphate aromatic ester (generic). 721.10289 Section 721.10289 Protection of... polymer with aliphatic polyol dihydrogen phosphate aromatic ester (generic). (a) Chemical substance and... acid polymer with aliphatic polyol dihydrogen phosphate aromatic ester (PMN P-11-333) is subject...

  8. 40 CFR 721.10289 - Hexanedioic acid polymer with aliphatic polyol dihydrogen phosphate aromatic ester (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... aliphatic polyol dihydrogen phosphate aromatic ester (generic). 721.10289 Section 721.10289 Protection of... polymer with aliphatic polyol dihydrogen phosphate aromatic ester (generic). (a) Chemical substance and... acid polymer with aliphatic polyol dihydrogen phosphate aromatic ester (PMN P-11-333) is subject...

  9. Photochemistry of (E)-1-(9-anthryl)-2-(4-nitrophenyl)ethene in the presence of aliphatic amines: H-bonding and charge-transfer effects.

    PubMed

    Bortolus, Pietro; Galiazzo, Guido; Gennari, Giorgio; Monti, Sandra E

    2002-06-01

    Polysubstituted aliphatic and aromatic amines and alcohols quench the fluorescence of (E)-1-(9-anthryl)-2-(4-nitrophenyl)ethene (NA). The quenching occurs without modification of the NA emission characteristics, follows a Stern-Volmer (SV) relationship and correlates with the decrease of the photoisomerization and intersystem crossing (ISC) yields. The dependence of the quenching rate constants (k(q)) on the ionization potentials suggests a charge-transfer interaction for the amines. The dependence of the k(q) values on alcohol acidity indicates the intervention of H-bonding phenomena. The interaction of primary aliphatic amines and NA in low-polarity solvents results in a broadening and a quenching of the NA emission. The quenching does not follow the SV relationship, has no effect on the E --> Z photoisomerization nor on the population of the triplet state, and increases the yield of the photobleaching reaction, especially in more polar solvents (chlorobenzene). This peculiar behaviour of primary aliphatic amines is attributed to H-bonded complexes in both the ground and the lowest excited singlet state. PMID:12856709

  10. Development of an impact- and solvent-resistant thermoplastic composite matrix

    NASA Technical Reports Server (NTRS)

    Delano, C. B.; Kiskiras, C. J.

    1984-01-01

    Synthesis, moldability and chloroform, acetone and tricresyl phosphate resistance of 16 polymer compositions are described. These aliphatic heterocyclic polymers include polyimides, polybenzimidazoles, and N-arylenepolybenzimidazoles. A solution condensation (cresol) method to prepare imidized aliphaic polyimides is described. Two polyimides and one polybenzimidazole demonstrate no crazing or cracking during 500 hr exposure to the cited solvents under stress. Modification of one aliphatic polyimide with several aromatic amines suggests that m-phenylenediamine is singular in its behavior to improve the chloroform resistance of that class of polyimides.

  11. Aqueous solubility and octan-1-ol to water partition coefficients of aliphatic hydrocarbons

    SciTech Connect

    Coates, M.; Connell, D.W.; Barron, D.M.

    1985-07-01

    The aqueous solubility (S) and octanol-water partition coefficients (P) of homologous series of n-, 2-methyl-, and 3-methylalkanes, as well as 1-alkenes, have been determined by extrapolation of known results, direct measurement, and high-pressure liquid chromatography (HP-LC). Long-term equilibration experiments, used to reduce aggregate formation, indicated that n-dodecane and n-tetradecane have S values in agreement with those obtained by extrapolation of the data on lower members. HPLC data from reverse-phase columns further validated the use of extrapolation. By use of published values for P and S for lower n-alkanes, the relationships between log P, log S, and N/sub c/ were obtained. Cochromatography of n-alkanes with members of the other series then allowed these relationships to be determined for the 2- and 3-methylalkanes and the 1-alkenes. The derived S values were in reasonable agreement with values from previous work and those obtained by extrapolation. The log P values have not been previously determined for these compounds.

  12. ANAEROBIC BIOTRANSFORMATION OF CHLORINATED ALIPHATIC HYDROCARBONS: UGLY DUCKLING TO BEAUTIFUL SWAN. (R825549C053)

    EPA Science Inventory

    The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

  13. ANAEROBIC BIOTRANSFORRNATION OF CHLORINATED ALIPHATIC HYDROCARBONS: UGLY DUCKLING TO BEAUTIFUL SWAN. (R825549C044)

    EPA Science Inventory

    The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

  14. BIOTRANSFORMATIONS OF SELECTED ALKYLBENZENES AND HALOGENATED ALIPHATIC HYDROCARBONS IN METHANOGENIC AQUIFER MATERIAL: A MICROCOSM STUDY

    EPA Science Inventory

    Leachates from municipal landfills commonly contain a variety of organic contaminants of industrial origin. The behavior of these compounds in anaerobic, and particularly in methanogenic, subsurface materials is poorly understood. The behavior of benzene, toluene, ethylbenzene, o...

  15. Economic combinative solvent and catalytic dewaxing process employing methylisopropyl ketone as the solvent and a silicate-based catalyst

    SciTech Connect

    Stem, S.C.

    1986-11-11

    This patent describes a process for the combinative dewaxing of a lubricating oil having a wax content which comprises: (a) contacting a waxy lubricating oil with a solvent comprising a ketone and an aromatic hydrocarbon selected from the group consisting of benzene, toluene, xylene and cumene in a solvent dewaxing zone, at solvent dewaxing conditions. This produces a partially dewaxed lubricating oil containing the ketone and the aromatic hydrocarbon and a slack wax stream containing hard wax, soft wax containing lubricating oil therewith, ketone, and aromatic hydrocarbon; (b) passing the partially dewaxed lubricating oil and slack wax stream to a first separation zone, and separating therein the partially dewaxed lubricating oil from the slack wax stream; (c) removing the ketone and the aromatic hydrocarbon from the partially dewaxed lubricating oil and contacting the partially dewaxed lubricating oil with a dewaxing catalyst, in a catalytic dewaxing zone, at catalytic dewaxing conditions, to produce a dewaxed lubricating oil; (d) treating, in a second dewaxing zone, the slack wax stream to separate the hard wax from the soft wax containing lubricating oil and the ketone solvent and the aromatic hydrocarbon from the slack wax stream; (e) recycling at least a portion of the ketone and aromatic hydrocarbon from step (d) to the solvent dewaxing zone of step (a) or the second dewaxing zone of step (d); and (f) passing the soft wax containing lubricating oil to a catalytic dewaxing zone to convert the soft wax and to thereby increase the produced quantity of lubricating oil. The improvement described here consists of use of the use of methylisopropyl ketone as the solvent ketone in the solvent dewaxing zone of step (a).

  16. Analysis of aliphatic waxes associated with root periderm or exodermis from eleven plant species.

    PubMed

    Kosma, Dylan K; Rice, Adam; Pollard, Mike

    2015-09-01

    Aliphatic waxes can be found in association with suberized tissues, including roots. Non-polar lipids were isolated by rapid solvent extraction of mature regions of intact roots from eleven angiosperms, including both monocots and dicots. The majority of roots analyzed were taproots or tuberous taproots that had undergone secondary growth and thus were covered by a suberized periderm. The exceptions therein were maize (Zea mays L.) and rice (Oryza sativa L.), which present a suberized exodermis. The analysis herein focused on aliphatic waxes, with particular emphasis on alkyl hydroxycinnamates (AHCs). AHCs were widely distributed, absent from only one species, were found in both aerial and subterranean portions of tuberous taproots, and were associated with the fibrous roots of both maize and rice. Most species also contained monoacylglycerols, fatty alcohols and/or free fatty acids. Carrot (Daucus carrota L.) was the outlier, containing only free fatty acids, sterols, and polyacetylenes as identified components. Sterols were the only ubiquitous component across all roots analyzed. Monoacylglycerols of ω-hydroxy fatty acids were present in maize and rice root waxes. For species within the Brassiceae, wax compositions varied between subspecies or varieties and between aerial and subterranean portions of taproots. In addition, reduced forms of photo-oxidation products of ω-hydroxy oleate and its corresponding dicarboxylic acid (10,18-dihydroxy-octadec-8-enoate, 9,18-dihydroxy-octadec-10-enoate and 9-hydroxyoctadec-10-ene-1,18-dioate) were identified as naturally occurring suberin monomers in rutabaga (Brassica napus subsp. rapifera Metzg.) periderm tissues. PMID:26143051

  17. Olfactory sensitivity and odor structure-activity relationships for aliphatic ketones in CD-1 mice.

    PubMed

    Laska, Matthias

    2014-06-01

    Using a conditioning paradigm, the olfactory sensitivity of CD-1 mice for a homologous series of aliphatic 2-ketones (2-butanone to 2-nonanone) and several of their isomeric forms was investigated. With all 11 odorants, the animals significantly discriminated concentrations as low as 0.01 ppm (parts per million) from the solvent, and with two odorants (2-octanone and 5-nonanone), the best-scoring animals even detected concentrations as low as 3 ppt (parts per trillion). Analysis of odor structure-activity relationships showed that the correlation between olfactory detection thresholds of the mice for the 2-ketones and carbon chain length can best be described as a U-shaped function with the lowest threshold values at 2-octanone. Similarly, the correlation between olfactory sensitivity and carbon chain length of symmetrical ketones (3-pentanone to 6-undecanone) can best be described as a U-shaped function. In contrast, no significant correlation was found between olfactory detection thresholds of the mice and position of the functional carbonyl group attached to a C7 backbone. A comparison between the olfactory detection thresholds obtained here with those obtained in earlier studies suggests that mice are significantly more sensitive for 2-ketones than for n-carboxylic acids of the same carbon chain length. Across-species comparisons suggest that mice are significantly more sensitive for aliphatic ketones than squirrel monkeys and pigtail macaques, whereas the ranges of human olfactory detection threshold values overlap with those of the mice with seven of the 11 ketones tested. Further comparisons suggest that odor structure-activity relationships are both substance class and species specific. PMID:24621664

  18. Hydrocarbons on Saturn's satellites Iapetus and Phoebe

    USGS Publications Warehouse

    Cruikshank, D.P.; Wegryn, E.; Dalle, Ore C.M.; Brown, R.H.; Bibring, J.-P.; Buratti, B.J.; Clark, R.N.; McCord, T.B.; Nicholson, P.D.; Pendleton, Y.J.; Owen, T.C.; Filacchione, G.; Coradini, A.; Cerroni, P.; Capaccioni, F.; Jaumann, R.; Nelson, R.M.; Baines, K.H.; Sotin, C.; Bellucci, G.; Combes, M.; Langevin, Y.; Sicardy, B.; Matson, D.L.; Formisano, V.; Drossart, P.; Mennella, V.

    2008-01-01

    Material of low geometric albedo (pV ??? 0.1) is found on many objects in the outer Solar System, but its distribution in the saturnian satellite system is of special interest because of its juxtaposition with high-albedo ice. In the absence of clear, diagnostic spectral features, the composition of this low-albedo (or "dark") material is generally inferred to be carbon-rich, but the form(s) of the carbon is unknown. Near-infrared spectra of the low-albedo hemisphere of Saturn's satellite Iapetus were obtained with the Visible-Infrared Mapping Spectrometer (VIMS) on the Cassini spacecraft at the fly-by of that satellite of 31 December 2004, yielding a maximum spatial resolution on the satellite's surface of ???65 km. The spectral region 3-3.6 ??m reveals a broad absorption band, centered at 3.29 ??m, and concentrated in a region comprising about 15% of the low-albedo surface area. This is identified as the C{single bond}H stretching mode vibration in polycyclic aromatic hydrocarbon (PAH) molecules. Two weaker bands attributed to {single bond}CH2{single bond} stretching modes in aliphatic hydrocarbons are found in association with the aromatic band. The bands most likely arise from aromatic and aliphatic units in complex macromolecular carbonaceous material with a kerogen- or coal-like structure, similar to that in carbonaceous meteorites. VIMS spectra of Phoebe, encountered by Cassini on 11 June 2004, also show the aromatic hydrocarbon band, although somewhat weaker than on Iapetus. The origin of the PAH molecular material on these two satellites is unknown, but PAHs are found in carbonaceous meteorites, cometary dust particles, circumstellar dust, and interstellar dust. ?? 2007 Elsevier Inc. All rights reserved.

  19. The effects of solvent and temperature on the structural integrity of monomeric melittin by molecular dynamics simulations

    NASA Astrophysics Data System (ADS)

    Liu, Hsuan-Liang; Hsu, Chia-Ming

    2003-06-01

    In this study, the secondary structural integrity of monomeric melittin was shown to depend strongly on the solvent by 200 ps molecular dynamics simulations with temperature jump technique. The α-helix content of melittin increased with increasing the aliphatic chain length of alcohol and decreased with increasing simulation temperature. In addition, the melting temperature of melittin, at which the averaged helicity decreased to 50%, was linearly correlated to the aliphatic chain length of alcohol. The weaker dielectric constant of longer aliphatic chain length of alcohol possibly reduces the hydrogen bonding between amide protons and surrounding solvent molecules and simultaneously promotes the intramolecular hydrogen bonding in melittin and therefore stabilizes the secondary structure of melittin.

  20. Solvent wash solution

    DOEpatents

    Neace, J.C.

    1984-03-13

    A process is claimed for removing diluent degradation products from a solvent extraction solution, which has been used to recover uranium and plutonium from spent nuclear fuel. A wash solution and the solvent extraction solution are combined. The wash solution contains (a) water and (b) up to about, and including, 50 vol % of at least one-polar water-miscible organic solvent based on the total volume of the water and the highly-polar organic solvent. The wash solution also preferably contains at least one inorganic salt. The diluent degradation products dissolve in the highly-polar organic solvent and the organic solvent extraction solvent do not dissolve in the highly-polar organic solvent. The highly-polar organic solvent and the extraction solvent are separated.

  1. Solvent wash solution

    DOEpatents

    Neace, James C.

    1986-01-01

    Process for removing diluent degradation products from a solvent extraction solution, which has been used to recover uranium and plutonium from spent nuclear fuel. A wash solution and the solvent extraction solution are combined. The wash solution contains (a) water and (b) up to about, and including, 50 volume percent of at least one-polar water-miscible organic solvent based on the total volume of the water and the highly-polar organic solvent. The wash solution also preferably contains at least one inorganic salt. The diluent degradation products dissolve in the highly-polar organic solvent and the organic solvent extraction solvent do not dissolve in the highly-polar organic solvent. The highly-polar organic solvent and the extraction solvent are separated.

  2. A biotechnological approach to the synthesis of epoxides: bioconversion of hydrocarbons by Pseudomonas oleovorans during growth in a multiphase system

    SciTech Connect

    De Smet, M.J.

    1983-04-01

    This communication examines the oxidation of alkanes and alkenes by Pseudomonas oleovorans. A variety of substrates were tested in order to extend the practical use of P. oleovorans for the synthesis of chiral epoxides. Concludes that hydrocarbon fermentations of P. oleovorans might be an important tool not only in the production of epoxides but also in the production of aliphatic polyesters and biosurfactants.

  3. 40 CFR Table 6 to Subpart Qqqq of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Default Organic HAP Mass Fraction for... HAP Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction values in the following... type Average organic HAP mass fraction Typical organic HAP, percent by mass Aliphatic b 0.03 1%...

  4. 40 CFR Table 4 to Subpart Nnnn of... - Default Organic HAP Mass Fraction for Petroleum Solvent Groups a

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 12 2011-07-01 2009-07-01 true Default Organic HAP Mass Fraction for... Mass Fraction for Petroleum Solvent Groups a You may use the mass fraction values in the following... type Average organic HAP mass fraction Typical organic HAP, percent by mass Aliphatic b 0.03 1%...

  5. Classification and thermal history of petroleum based on light hydrocarbons

    NASA Astrophysics Data System (ADS)

    Thompson, K. F. M.

    1983-02-01

    Classifications of oils and kerogens are described. Two indices are employed, termed the Heptane and IsoheptaneValues, based on analyses of gasoline-range hydrocarbons. The indices assess degree of paraffinicity. and allow the definition of four types of oil: normal, mature, supermature, and biodegraded. The values of these indices measured in sediment extracts are a function of maximum attained temperature and of kerogen type. Aliphatic and aromatic kerogens are definable. Only the extracts of sediments bearing aliphatic kerogens having a specific thermal history are identical to the normal oils which form the largest group (41%) in the sample set. This group was evidently generated at subsurface temperatures of the order of 138°-149°C, (280°-300°F) defined under specific conditions of burial history. It is suggested that all other petroleums are transformation products of normal oils.

  6. Changes in psychological performances of solvent-poisoned and solvent-exposed workers

    SciTech Connect

    Lindstroem, K.

    1980-01-01

    The changes in psychological performances associated with long-term exposure to organic solvents and solvent mixtures were studied in a group of 56 male workers diagnosed as having an occupational disease caused by solvents. Their mean duration of exposure was 9.1 +/- SD 8.3 years, and they were exposed mainly to halogenated and aromatic hydrocarbons and to mixtures of paint solvents. The psychological performances of these solvent-exposed patients were compared with those of 98 styrene-exposed workers and a nonexposed group of 43 construction workers. The applied psychological test variables were factor analyzed, before other statistical analysis, in order to clarify what they measured in the present study. The solvent-exposed group was characterized by a decline in visuomotor performance and decreased freedom from distractibility. The poor visuomotor performances were also related to the long duration of solvent exposure in this group of patients. The index applied for the exposure level revealed no significant relationships to psychological performances among the solvent-exposed patients. The psychological performances of the styrene-exposed group differed only very slightly from those of the nonexposed workers.

  7. Biodegradation of Trihalomethanes and Other Halogenated Aliphatic Compounds

    NASA Technical Reports Server (NTRS)

    Smith, G. B.

    1996-01-01

    The biological dehalogenation of common water pollutants such as trichloromethane (chloroform) and other halogenated aliphatic compounds was the subject of this project. Samples from diverse water environments such as from groundwater contaminated with halogenated compounds and wastewaters from regional treatment plants were studied to identify conditions that favor certain dehalogenation reactions over others. Gene probe analyses of DNA extracted from the dichlormethane-degrading wastewater indicated the presence of the gene coding for dichloromethane dehalogenase, indicating the genetic basis for the dechlorination activity observed. These studies indicate that methanogenic bacteria are the organisms responsible for the chloroform dechlorination. Dechlorination of a common chlorofluorocarbon (CFC-11) was identified in samples taken from a regional aquifer contaminated with halogenated aliphatic compounds.

  8. Manganese-Mediated Coupling Reaction of Vinylarenes and Aliphatic Alcohols

    PubMed Central

    Zhang, Wei; Wang, Nai-Xing; Bai, Cui-Bing; Wang, Yan-Jing; Lan, Xing-Wang; Xing, Yalan; Li, Yi-He; Wen, Jia-Long

    2015-01-01

    Alcohols and alkenes are the most abundant and commonly used organic building blocks in the large-scale chemical synthesis. Herein, this is the first time to report a novel and operationally simple coupling reaction of vinylarenes and aliphatic alcohols catalyzed by manganese in the presence of TBHP (tert-butyl hydroperoxide). This coupling reaction provides the oxyalkylated products of vinylarenes with good regioselectivity and accomplishes with the principles of step-economies. A possible reaction mechanism has also been proposed. PMID:26470633

  9. 40 CFR 721.4490 - Capped aliphatic isocyanate.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... reporting. (1) The chemical substance identified generically as a capped aliphatic isocyanate (PMN P-86-1146...) (concentration set at 0.1 percent), (f), (h)(1)(ii)(G), (h)(1)(iii)(A), (h)(1)(iii)(B), (h)(1)(iii)(D), and (h)(1...(h). (iv) Disposal. Requirements as specified in § 721.90 (a)(1), (a)(2), (b)(1), (b)(2), (c)(1),...

  10. 40 CFR 721.4490 - Capped aliphatic isocyanate.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... reporting. (1) The chemical substance identified generically as a capped aliphatic isocyanate (PMN P-86-1146...) (concentration set at 0.1 percent), (f), (h)(1)(ii)(G), (h)(1)(iii)(A), (h)(1)(iii)(B), (h)(1)(iii)(D), and (h)(1...(h). (iv) Disposal. Requirements as specified in § 721.90 (a)(1), (a)(2), (b)(1), (b)(2), (c)(1),...

  11. 40 CFR 721.4490 - Capped aliphatic isocyanate.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... reporting. (1) The chemical substance identified generically as a capped aliphatic isocyanate (PMN P-86-1146...) (concentration set at 0.1 percent), (f), (h)(1)(ii)(G), (h)(1)(iii)(A), (h)(1)(iii)(B), (h)(1)(iii)(D), and (h)(1...(h). (iv) Disposal. Requirements as specified in § 721.90 (a)(1), (a)(2), (b)(1), (b)(2), (c)(1),...

  12. 40 CFR 721.4490 - Capped aliphatic isocyanate.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... reporting. (1) The chemical substance identified generically as a capped aliphatic isocyanate (PMN P-86-1146...) (concentration set at 0.1 percent), (f), (h)(1)(ii)(G), (h)(1)(iii)(A), (h)(1)(iii)(B), (h)(1)(iii)(D), and (h)(1...(h). (iv) Disposal. Requirements as specified in § 721.90 (a)(1), (a)(2), (b)(1), (b)(2), (c)(1),...

  13. Rhodium-Catalyzed Enantioselective Arylation of Aliphatic Imines.

    PubMed

    Kato, Naoya; Shirai, Tomohiko; Yamamoto, Yasunori

    2016-06-01

    Chiral rhodium(I)-catalyzed highly enantioselective arylation of aliphatic N-sulfonyl aldimines with arylboronic acids has been developed. This transformation is achieved by the use of a rhodium/bis(phosphoramidite) catalyst to give enantiomerically enriched α-branched amines (up to 99 % ee). In addition, this system enables efficient synthesis of (+)-NPS R-568 and Cinacalcet which are calcimimetic agents. PMID:27119262

  14. Mechanics of networks of aliphatic fibers in aqueous surfactant media

    NASA Astrophysics Data System (ADS)

    Zanchetta, Giuliano; Caggioni, Marco; Guida, Vincenzo; Trappe, Veronique

    2012-02-01

    We investigate the structural and rheological properties of aliphatic fibers dispersed in aqueous solutions of anionic surfactants, typically used in liquid detergents to provide yield stress. This system displays an onset to solid-like properties that depends on fiber concentration. In this contribution we will discuss how tuning the state of the surfactant background influences the fiber-fiber interactions and the mechanical properties of the gel.

  15. Manganese-Mediated Coupling Reaction of Vinylarenes and Aliphatic Alcohols.

    PubMed

    Zhang, Wei; Wang, Nai-Xing; Bai, Cui-Bing; Wang, Yan-Jing; Lan, Xing-Wang; Xing, Yalan; Li, Yi-He; Wen, Jia-Long

    2015-01-01

    Alcohols and alkenes are the most abundant and commonly used organic building blocks in the large-scale chemical synthesis. Herein, this is the first time to report a novel and operationally simple coupling reaction of vinylarenes and aliphatic alcohols catalyzed by manganese in the presence of TBHP (tert-butyl hydroperoxide). This coupling reaction provides the oxyalkylated products of vinylarenes with good regioselectivity and accomplishes with the principles of step-economies. A possible reaction mechanism has also been proposed. PMID:26470633

  16. Manganese-Mediated Coupling Reaction of Vinylarenes and Aliphatic Alcohols

    NASA Astrophysics Data System (ADS)

    Zhang, Wei; Wang, Nai-Xing; Bai, Cui-Bing; Wang, Yan-Jing; Lan, Xing-Wang; Xing, Yalan; Li, Yi-He; Wen, Jia-Long

    2015-10-01

    Alcohols and alkenes are the most abundant and commonly used organic building blocks in the large-scale chemical synthesis. Herein, this is the first time to report a novel and operationally simple coupling reaction of vinylarenes and aliphatic alcohols catalyzed by manganese in the presence of TBHP (tert-butyl hydroperoxide). This coupling reaction provides the oxyalkylated products of vinylarenes with good regioselectivity and accomplishes with the principles of step-economies. A possible reaction mechanism has also been proposed.

  17. Effect of solvent characteristics on coal liquefaction

    SciTech Connect

    Huang, He; Wang, Shaojie; Wang, Keyu; Klein, M.T.; Calkins, W.H.

    1996-12-31

    It has been known for a long time that the characteristics of the liquefaction solvent has a profound effect on direct coal liquefaction. The amount of hydrogen consumed during the liquefaction process, the degree and quantity of retrograde reactions that occur, and the quality of the liquid products are all influenced by the process solvent. A number of analytical approaches have been developed to determine the important characteristics of the solvent for coal liquefaction. The hydrogen donor ability has clearly been important. However, such other characteristics of a liquefaction solvent as solubility parameter, content and type of higher aromatic hydrocarbons, and phenolic content have also been found to be significant. Finseth et al. have shown that the bulk of the hydrogen consumed from an uncatalyzed donor solvent liquefaction above 400{degrees}C is consumed in gas generation, heteroatom removal and hydrogenolysis of the coal matrix. Wilson et al. have also shown that the major role of hydrogen in uncatalyzed liquefaction is consumed by alkyl fission and hydrogenolysis reactions and not with hydrogenating aromatic rings. McMillan et al. have postulated that a radical hydrogen transfer process along with donor solvent capping of thermally produced radicals from the coal as possible processes involved with the hydroaromatic donor solvents in coal liquefaction. With the development of a short contact time batch reactor (SCTBR), determining the influence of the processing solvent on the liquefaction rates, conversion profiles and the quality of the liquid product at a particular time became possible. The influence of type of solvent, combined with other effects, such as gas atmosphere (i.e., in hydrogen and in nitrogen) and catalyst, on the coal liquefaction is reported in this paper.

  18. Cost-Benefit Analysis for Alternatives to Aliphatic Isocyanate Polyurethanes

    NASA Technical Reports Server (NTRS)

    Lewis, Pattie

    2007-01-01

    NASA and Air Force Space Command (AFSPC) have similar missions and therefore similar facilities and structures in similar environments. The standard practice for protecting metallic substrates in atmospheric environments is the application of an applied coating system. The most common topcoats used in coating systems are polyurethanes that contain isocyanates. Isocyanates are classified as potential human carcinogens and are known to cause cancer in animals. The primary objective of this effort was to demonstrate and validate alternatives to aliphatic isocyanate polyurethanes resulting in one or more isocyanate-free coatings qualified for use at AFSPC and NASA installations participating in this project. This Cost-Benefit Analysis (CBA) quantifies the estimated capital and process costs of coating alternatives and cost savings relative to the current coatings. The estimates in this CBA are to be used for assessing the relative merits of the selected alternatives. The actual economic effects at any specific facility will depend on the alternative material or technology implemented, the number of actual applications converted, future workloads, and other factors . The participants initially considered eighteen (18) alternative coatings as described in the Potential Alternatives Report entitled Potential Alternatives Report for Validation of Alternatives to Aliphatic Isocyanate Polyurethanes, prepared by ITB. Of those, 8 alternatives were selected for testing in accordance with the Joint Test Protocol entitled Joint Test Protocol for Validation of Alternatives to Aliphatic Isocyanate Polyurethanes, and the Field Test Plan entitled Field Evaluations Test Plan for Validation of Alternatives 10 Aliphatic Isocyanate Polyurethanes, both of which were prepared by ITB. A joint Test Report entitled Joint Test Report for Validation of Alternatives to Aliphatic Isocyanate Polyurethanes, prepared by ITB, documents the results of the laboratory and field testing, as well as any

  19. Sum frequency generation image reconstruction: aliphatic membrane under spherical cap geometry.

    PubMed

    Volkov, Victor

    2014-10-01

    The article explores an opportunity to approach structural properties of phospholipid membranes using Sum Frequency Generation microscopy. To establish the principles of sum frequency generation image reconstruction in such systems, at first approach, we may adopt an idealistic spherical cap uniform assembly of hydrocarbon molecules. Quantum mechanical studies for decanoic acid (used here as a representative molecular system) provide necessary information on transition dipole moments and Raman tensors of the normal modes specific to methyl terminal - a typical moiety in aliphatic (and phospholipid) membranes. Relative degree of localization and frequencies of the normal modes of methyl terminals make nonlinearities of this moiety to be promising in structural analysis using Sum Frequency Generation imaging. Accordingly, the article describes derivations of relevant macroscopic nonlinearities and suggests a mapping procedure to translate amplitudes of the nonlinearities onto microscopy image plane according to geometry of spherical assembly, local molecular orientation, and optical geometry. Reconstructed images indicate a possibility to extract local curvature of bilayer envelopes of spherical character. This may have practical implications for structural extractions in membrane systems of practical relevance. PMID:25296798

  20. Road tunnel, roadside, and urban background measurements of aliphatic compounds in size-segregated particulate matter

    NASA Astrophysics Data System (ADS)

    Alves, Célia A.; Oliveira, César; Martins, Natércia; Mirante, Fátima; Caseiro, Alexandre; Pio, Casimiro; Matos, Manuel; Silva, Hugo F.; Oliveira, Cristina; Camões, Filomena

    2016-02-01

    Particulate matter samples were collected in a road tunnel in Lisbon (PM0.5, PM0.5-1, PM1-2.5, and PM2.5-10) and at two urban locations representing roadside and background stations (PM2.5 and PM2.5-10). Samples were analysed for organic and elemental carbon (OC and EC), n-alkanes, n-alkenes, hopanes, some isoprenoid compounds, and steranes. Particulate matter concentrations in the tunnel were 17-31 times higher than at roadside in the vicinity, evidencing an aerosol origin almost exclusively in fresh vehicle emissions. PM0.5 in the tunnel comprised more than 60% and 80% of the total OC and EC mass in PM10, respectively. Concentrations of the different aliphatic groups of compounds in the tunnel were up to 89 times higher than at roadside and 143 times higher than at urban background. Based on the application of hopane-to-OC or hopanes-to-EC ratios obtained in the tunnel, it was found that vehicle emissions are the dominant contributor to carbonaceous particles in the city but do not represent the only source of these triterpenic compounds. Contrary to what has been observed in other studies, the Σhopane-to-EC ratios were higher in summer than in winter, suggesting that other factors (e.g. biomass burning, dust resuspension, and different fuels/engine technologies) prevail in relation to the photochemical decay of triterpenoid hydrocarbons from vehicle exhaust.

  1. Sum frequency generation image reconstruction: Aliphatic membrane under spherical cap geometry

    SciTech Connect

    Volkov, Victor

    2014-10-07

    The article explores an opportunity to approach structural properties of phospholipid membranes using Sum Frequency Generation microscopy. To establish the principles of sum frequency generation image reconstruction in such systems, at first approach, we may adopt an idealistic spherical cap uniform assembly of hydrocarbon molecules. Quantum mechanical studies for decanoic acid (used here as a representative molecular system) provide necessary information on transition dipole moments and Raman tensors of the normal modes specific to methyl terminal – a typical moiety in aliphatic (and phospholipid) membranes. Relative degree of localization and frequencies of the normal modes of methyl terminals make nonlinearities of this moiety to be promising in structural analysis using Sum Frequency Generation imaging. Accordingly, the article describes derivations of relevant macroscopic nonlinearities and suggests a mapping procedure to translate amplitudes of the nonlinearities onto microscopy image plane according to geometry of spherical assembly, local molecular orientation, and optical geometry. Reconstructed images indicate a possibility to extract local curvature of bilayer envelopes of spherical character. This may have practical implications for structural extractions in membrane systems of practical relevance.

  2. Field demonstration for P-D-680 solvent replacement. interim report

    SciTech Connect

    Rhee, I.S.; Velez, C.

    1996-10-01

    As part of the second phase in development of environmentally compliant solvent alternatives to P-D-680, field demonstrations were initiated at Ft. Lewis WA, Ft. Hood TX, and Kelly Air Force Base. The main objectives of this demonstration were to validate performance of candidate solvents with existing military equipment and to determine the environmental applicability for these candidate solvents. Four (4) petroleum based solvents and four (4) terpene/hydrocarbon blended solvents have been selected as candidates for these field demonstrations. Ft. Lewis was designated as a major field testing site and evaluated eight (8) candidate solvents in various military ground equipment, helicopter, and weapon cleaning application. Ft. Hood evaluated two (2) different types of candidate solvents in helicopter maintenance applications. San Antonio Air Logistic Center at Kelly AFB evaluated three (3) candidate solvents using existing part washers for aviation applications. Field test results showed that both severe hydrotreated odorless hydrocarbon solvents and hydrotreated terpene/hydrocarbon blended solvents were well accepted in all applications. Six candidate solvents were rated by users as acceptable replacements for P-D-680.

  3. Quantitative structure-activity relationship (QSAR) prediction of (eco)toxicity of short aliphatic protic ionic liquids.

    PubMed

    Peric, Brezana; Sierra, Jordi; Martí, Esther; Cruañas, Robert; Garau, Maria Antonia

    2015-05-01

    Ionic liquids (ILs) are considered as a group of very promising compounds due to their excellent properties (practical non-volatility, high thermal stability and very good and diverse solving capacity). The ILs have a good prospect of replacing traditional organic solvents in vast variety of applications. However, the complete information on their environmental impact is still not available. There is also an enormous number of possible combinations of anions and cations which can form ILs, the fact that requires a method allowing the prediction of toxicity of existing and potential ILs. In this study, a group contribution QSAR model has been used in order to predict the (eco)toxicity of protic and aprotic ILs for five tests (Microtox®, Pseudokirchneriella subcapitata and Lemna minor growth inhibition test, and Acetylcholinestherase inhibition and Cell viability assay with IPC-81 cells). The predicted and experimental toxicity are well correlated. A prediction of EC50 for these (eco)toxicity tests has also been made for eight representatives of the new family of short aliphatic protic ILs, whose toxicity has not been determined experimentally to date. The QSAR model applied in this study can allow the selection of potentially less toxic ILs amongst the existing ones (e.g. in the case of aprotic ILs), but it can also be very helpful in directing the synthesis efforts toward developing new "greener" ILs respectful with the environment (e.g. short aliphatic protic ILs). PMID:25728357

  4. Insights into the biodegradation of weathered hydrocarbons in contaminated soils by bioaugmentation and nutrient stimulation.

    PubMed

    Jiang, Ying; Brassington, Kirsty J; Prpich, George; Paton, Graeme I; Semple, Kirk T; Pollard, Simon J T; Coulon, Frédéric

    2016-10-01

    The potential for biotransformation of weathered hydrocarbon residues in soils collected from two commercial oil refinery sites (Soil A and B) was studied in microcosm experiments. Soil A has previously been subjected to on-site bioremediation and it was believed that no further degradation was possible while soil B has not been subjected to any treatment. A number of amendment strategies including bioaugmentation with hydrocarbon degrader, biostimulation with nutrients and soil grinding, were applied to the microcosms as putative biodegradation improvement strategies. The hydrocarbon concentrations in each amendment group were monitored throughout 112 days incubation. Microcosms treated with biostimulation (BS) and biostimulation/bioaugmentation (BS + BA) showed the most significant reductions in the aliphatic and aromatic hydrocarbon fractions. However, soil grinding was shown to reduce the effectiveness of a nutrient treatment on the extent of biotransformation by up to 25% and 20% for the aliphatic and aromatic hydrocarbon fractions, respectively. This is likely due to the disruption to the indigenous microbial community in the soil caused by grinding. Further, ecotoxicological responses (mustard seed germination and Microtox assays) showed that a reduction of total petroleum hydrocarbon (TPH) concentration in soil was not directly correlable to reduction in toxicity; thus monitoring TPH alone is not sufficient for assessing the environmental risk of a contaminated site after remediation. PMID:27441989

  5. Hydrocarbons in Lake Washington sediments. A 25-year retrospective in an urban lake.

    PubMed

    Wakeham, Stuart G; Forrest, James; Masiello, Caroline A; Gélinas, Yves; Alexander, Clark R; Leavitt, Peter R

    2004-01-15

    Aliphatic and polycyclic aromatic hydrocarbon and stable and radiocarbon isotope distributions are compared for dated cores from the 1970s and 2000 for a 25-year retrospective in Lake Washington, Seattle, WA (USA). Contamination of Lake Washington sediments by petrogenic aliphatic hydrocarbons and pyrolytic polycyclic aromatic hydrocarbons via atmospheric deposition and stormwater runoff peaked between the 1950s and 1970s and has since decreased as stormwater inputs have been reduced. Radiocarbon signatures (delta14C, per 1000) of total organic carbon decrease (increased "age") in the depth interval of highest hydrocarbon concentration. Graphitic black carbon in the year 2000 core showed a historical profile similar to that of the PAH; however high background sediments deposited before the founding of Seattle indicates a considerable nonindustrial component derived from weathering in the watershed. Unlike hydrocarbon contamination, input of terrestrial organic matter (tracked by long-chain fatty alcohols) has increased throughout the late 20th century, documenting a shift in pollutant sources away from hydrocarbons and toward anthropogenic erosion of the region's soils. PMID:14750717

  6. Hydrocarbons on the Icy Satellites of Saturn

    NASA Technical Reports Server (NTRS)

    Cruikshank, Dale P.

    2010-01-01

    The Visible-Infrared Mapping Spectrometer on the Cassini Spacecraft has obtained spectral reflectance maps of the satellites of Saturn in the wavelength region 0.4-5.1 micrometers since its insertion into Saturn orbit in late 2004. We have detected the spectral signature of the C-H stretching molecular mode of aromatic and aliphatic hydrocarbons in the low albedo material covering parts of several of Saturn's satellites, notably Iapetus and Phoebe (Cruikshank et al. 2008). The distribution of this material is complex, and in the case of Iapetus we are seeking to determine if it is related to the native grey-colored materials left as lag deposits upon evaporation of the ices, or represents in-fall from an external source, notably the newly discovered large dust ring originating at Phoebe. This report covers our latest exploration of the nature and source of this organic material.

  7. Method and apparatus for synthesizing hydrocarbons

    DOEpatents

    Colmenares, C.A.; Somorjai, G.A.; Maj, J.J.

    1985-04-16

    A method and apparatus for synthesizing a mixture of aliphatic alcohols having five carbons or less is disclosed. An equal molar ratio of CO and H/sub 2/ gases is caused to pass through a ThO/sub 2/ catalyst having a surface area of about 80 to 125 m/sup 2//g. The catalyst further optionally includes Na ions present as substitutional cations in an amount of about 5 to 10 atom %. At a temperature of about 570 to 630/sup 0/K, and at pressures of about 20 to 50 atm, methanol and isobutanol are the predominant products and are produced in amounts of about 90 wt % of the total hydrocarbon mixture. 6 figs.

  8. NEPTUNIUM SOLVENT EXTRACTION PROCESS

    DOEpatents

    Dawson, L.R.; Fields, P.R.

    1959-10-01

    The separation of neptunium from an aqueous solution by solvent extraction and the extraction of neptunium from the solvent solution are described. Neptunium is separated from an aqueous solution containing tetravalent or hexavalent neptunium nitrate, nitric acid, and a nitrate salting out agent, such as sodium nitrate, by contacting the solution with an organic solvent such as diethyl ether. Subsequently, the neptunium nitrate is extracted from the organic solvent extract phase with water.

  9. Hydrogen donor solvent coal liquefaction process

    DOEpatents

    Plumlee, Karl W.

    1978-01-01

    An indigenous hydrocarbon product stream boiling within a range of from about C.sub.1 -700.degree. F., preferably C.sub.1 -400.degree. F., is treated to produce an upgraded hydrocarbon fuel component and a component which can be recycled, with a suitable donor solvent, to a coal liquefaction zone to catalyze the reaction. In accordance therewith, a liquid hydrocarbon fraction with a high end boiling point range up to about 700.degree. F., preferably up to about 400.degree. F., is separated from a coal liquefaction zone effluent, the separated fraction is contacted with an alkaline medium to provide a hydrocarbon phase and an aqueous extract phase, the aqueous phase is neutralized, and contacted with a peroxygen compound to convert indigenous components of the aqueous phase of said hydrocarbon fraction into catalytic components, such that the aqueous stream is suitable for recycle to the coal liquefaction zone. Naturally occurring phenols and alkyl substituted phenols, found in the aqueous phase, are converted, by the addition of hydroxyl constituents to phenols, to dihydroxy benzenes which, as disclosed in copending Application Ser. Nos. 686,813 now U.S. Pat. No. 4,049,536; 686,814 now U.S. Pat. No. 4,049,537; 686,827 now U.S. Pat. No. 4,051,012 and 686,828, K. W. Plumlee et al, filed May 17, 1976, are suitable hydrogen transfer catalysts.

  10. Theoretical and experimental studies of the isomeric protonation in solution for a prototype aliphatic ring containing two nitrogens

    PubMed Central

    Maheshwari, Aditya; Kim, Yong-Wah

    2009-01-01

    Theoretical calculations were carried out for studying the tautomeric protonation of N-methyl piperazine as a prototype six-member aliphatic ring containing a secondary and a tertiary nitrogen atom. The protonation was investigated in three solvents: water, acetonitrile, and dichloromethane. Calculations were performed up to the B3LYP/aug-cc-pvtz and QCISD(T)/CBS levels by applying the IEF-PCM polarizable continuum dielectric solvent model. Relative solvation free energies also were calculated upon explicit solvent models by utilizing the free-energy perturbation theory as implemented in Monte Carlo simulations. The relative free energy for the N-methyl piperazine tautomer protonated at the secondary (NMps) rather than at the tertiary (NMpt) nitrogen was calculated at a ratio of 47/53 in infinitely dilute aqueous solution. The ratio further decreases in lower polarity solvents. In contrast, NMR experiments suggest that the protonation takes place primarily at the secondary nitrogen in 0.37 molar aqueous solution with NMps/NMpt = 80/20. The NMps tautomer is exclusive in dichloromethane at the same concentration. The discrepancy between theory and experiment was resolved by considering association equilibria in parallel with the protonation for the solute. As a result, the theoretically predicted tautomer ratios were obtained in close agreement with the experimental values. The NMps tautomer could form a preferable dimeric structure, where one or two chloride anion(s) is/are in hydrogen bonds with protons of the associating monomers. The calculations suggest that the proton relocation may take place by solvent assistance in water or along an intramolecular proton jump in the twist-boat conformation. The predicted activation free energy was about 10 kcal/mol on the basis of variable temperature NMR experiments in DCM. PMID:19994881

  11. A spectroscopic and theoretical study in the near-infrared region of low concentration aliphatic alcohols.

    PubMed

    Beć, Krzysztof B; Futami, Yoshisuke; Wójcik, Marek J; Ozaki, Yukihiro

    2016-05-11

    The near-infrared (NIR) spectra of low-concentration (5 × 10(-3) M) solutions in CCl4 of basic aliphatic alcohols, methanol, ethanol, and 1-propanol were, for the first time, calculated by second-order vibrational perturbation theory computations and were compared with the corresponding experimental data. Density functional theory (DFT) using single hybrid (B3LYP) and double hybrid (B2PLYP) density functionals and their derivatives with additional empirical dispersion correction (B3LYP-D3 and B2PLYP-D, respectively) and second order Møller-Plesset perturbation theory were used in combination with selected basis sets including fairly new basis sets from the "spectroscopic" SNS family, double-ζ SNSD and triple-ζ SNST basis sets. Each time, anharmonic vibrational modes and intensities were calculated by using second-order vibrational perturbation theory. The effect of solvent cavity on the calculated results was included by the application of a self-consistent reaction field with a polarized continuum model. Ethanol and 1-propanol have conformational isomerism; following a conformational analysis, theoretical spectra of all isomers were calculated and their final predicted NIR spectra were obtained as Boltzmann-averaged spectra of resolved conformers. For ethanol and 1-propanol, the observed broadening of the overtone band of the OH stretching mode was well reflected by the differences in the position of the relevant band among conformational isomers of these alcohols; the effect of solvent on broadening was also discussed. Detailed band assignments in the experimental NIR spectra of the studied alcohols were proposed based on the calculation of potential energy distributions. The final accuracy of the predicted NIR spectra for each of the theoretical methods was estimated based on the errors in calculated frequencies of overtones and combination bands. PMID:27137865

  12. Physicochemical and biological properties of nano-hydroxyapatite-reinforced aliphatic polyurethanes membranes.

    PubMed

    Liu, Haohuai; Zhang, Li; Li, Jidong; Zou, Qin; Zuo, Yi; Tian, Weidong; Li, Yubao

    2010-01-01

    Polymer nano-composite membranes, based on aliphatic biodegradable polyurethane (PU) elastomers and nano-hydroxyapatite (n-HA), were prepared by solvent casting and freeze-drying. The PU matrix was synthesized from 4,4'-dicyclohexylmethane diisocyanate (H(12) MDI), poly(ethylene glycol) (PEG), castor oil (CO) and 1,4-butandiol (BDO). The n-HA/PU membranes were characterized by SEM, XRD, IR, TG, mechanical test and in vitro biocompatibility. The results revealed that incorporation of 30 wt% n-HA into the PU matrix increased the tensile strength nearly by 186% and the elongation-at-break by 107% compared to pure PU. The addition of n-HA had the slight positive effect on the thermal stability of PU. Cell culture and MTT assays showed that the incorporation of n-HA into the PU matrix provided a favourable environment for initial cell adhesion, maintained cell viability and cell proliferation. These results suggested that the n-HA/PU composite membrane might be a prospective biodegradable guided bone regeneration (GBR) membrane for future applications. PMID:20537245

  13. Nonflammable, Nonaqueous, Low Atmospheric Impact, High Performance Cleaning Solvents

    NASA Technical Reports Server (NTRS)

    Dhooge, P. M.; Glass, S. M.; Nimitz, J. S.

    2001-01-01

    For many years, chlorofluorocarbon (CFC) and chlorocarbon solvents have played an important part in aerospace operations. These solvents found extensive use as cleaning and analysis (EPA) solvents in precision and critical cleaning. However, CFCs and chlorocarbon solvents have deleterious effects on the ozone layer, are relatively strong greenhouse gases, and some are suspect or known carcinogens. Because of their ozone-depletion potential (ODP), the Montreal Protocol and its amendments, as well as other environmental regulations, have resulted in the phaseout of CFC-113 and 1,1,1-trichloroethane (TCA). Although alternatives have been recommended, they do not perform as well as the original solvents. In addition, some analyses, such as the infrared analysis of extracted hydrocarbons, cannot be performed with the substitute solvents that contain C-H bonds. CFC-113 solvent has been used for many critical aerospace applications. CFC-113, also known as Freon (registered) TF, has been used extensively in NASA's cleaning facilities for precision and critical cleaning, in particular the final rinsing in Class 100 areas, with gas chromatography analysis of rinse residue. While some cleaning can be accomplished by other processes, there are certain critical applications where CFC-113 or a similar solvent is highly cost-effective and ensures safety. Oxygen system components are one example where a solvent compatible with oxygen and capable of removing fluorocarbon grease is needed. Electronic components and precision mechanical components can also be damaged by aggressive cleaning solvents.

  14. Method for coupling a hydrocarbon containing molecular species

    SciTech Connect

    Lingwood, C.A.

    1986-07-01

    A method is described of covalently coupling two molecular species comprising: (a) combining (i) a first molecular species having a functionality reactive with hydrocarbon when photo-activated; and (ii) a solution of at least one, hydrocarbon containing, molecular species in the absence of photo-radiation to which the functionality is sensitive; (b) removing the solvent; (c) irradiating the mixture with photo-radiation to which the functionality is photosensitive.

  15. Solvents and sustainable chemistry

    PubMed Central

    Welton, Tom

    2015-01-01

    Solvents are widely recognized to be of great environmental concern. The reduction of their use is one of the most important aims of green chemistry. In addition to this, the appropriate selection of solvent for a process can greatly improve the sustainability of a chemical production process. There has also been extensive research into the application of so-called green solvents, such as ionic liquids and supercritical fluids. However, most examples of solvent technologies that give improved sustainability come from the application of well-established solvents. It is also apparent that the successful implementation of environmentally sustainable processes must be accompanied by improvements in commercial performance. PMID:26730217

  16. Solvent recycle/recovery

    SciTech Connect

    Paffhausen, M.W.; Smith, D.L.; Ugaki, S.N.

    1990-09-01

    This report describes Phase I of the Solvent Recycle/Recovery Task of the DOE Chlorinated Solvent Substitution Program for the US Air Force by the Idaho National Engineering Laboratory, EG G Idaho, Inc., through the US Department of Energy, Idaho Operations Office. The purpose of the task is to identify and test recovery and recycling technologies for proposed substitution solvents identified by the Biodegradable Solvent Substitution Program and the Alternative Solvents/Technologies for Paint Stripping Program with the overall objective of minimizing hazardous wastes. A literature search to identify recycle/recovery technologies and initial distillation studies has been conducted. 4 refs.

  17. Dual solvent refining process

    SciTech Connect

    Woodle, R.A.

    1982-04-20

    A dual solvent refining process is claimed for solvent refining petroleum based lubricating oil stocks with n-methyl-2-pyrrolidone as selective solvent for aromatic oils wherein a highly paraffinic oil having a narrow boiling range approximating the boiling point of n-methyl-2-pyrrolidone is employed as a backwash solvent. The process of the invention results in an increased yield of refined lubricating oil stock of a predetermined quality and simplifies separation of the solvents from the extract and raffinate oil fractions.

  18. Aromatic and aliphatic organic materials on Iapetus: Analysis of Cassini VIMS data

    NASA Astrophysics Data System (ADS)

    Cruikshank, Dale P.; Dalle Ore, Cristina M.; Clark, Roger N.; Pendleton, Yvonne J.

    2014-05-01

    We present a quantitative analysis of the hydrocarbon and other organic molecular inventory as a component of the low-albedo material of Saturn’s satellite Iapetus, based on a revision of the calibration of the Cassini VIMS instrument. Our study uses hyperspectral data from a mosaic of Iapetus’ surface (Pinilla-Alonso, N., Roush, T.L., Marzo, G.A., Cruikshank, D.P., Dalle Ore, C.M. [2011]. Icarus 215, 75-82) constructed from VIMS data on a close fly-by of the satellite. We extracted 2235 individual spectra of the low-albedo regions, and with a clustering analysis tool (Dalle Ore, C.M., Cruikshank, D.P., Clark, R.N. [2012]. Icarus 221, 735-743), separated them into two spectrally distinct groups, one concentrated on the leading hemisphere of Iapetus, and the other group on the trailing. This distribution is broadly consistent with that found from Cassini ISS data analyzed by Denk et al. (Denk, T. et al. [2010]. Science 327, 435-439). We modeled the average spectra of the two geographic regions using the materials and techniques described by Clark et al. (Clark, R.N., Cruikshank, D.P., Jaumann, R., Brown, R.H., Stephan, K., Dalle Ore, C.M., Livio, K.E., Pearson, N., Curchin, J.M., Hoefen, T.M., Buratti, B.J., Filacchione, G., Baines, K.H., Nicholson, P.D. [2012]. Icarus 218, 831-860), and after dividing the Iapetus spectrum by the model for each case, we extracted the resulting spectra in the interval 2.7-4.0 μm for analysis of the organic molecular bands. The spectra reveal the Csbnd H stretching modes of aromatic hydrocarbons at ∼3.28 μm (∼3050 cm-1), plus four blended bands of aliphatic sbnd CH2sbnd and sbnd CH3 in the range ∼3.36-3.52 μm (∼2980-2840 cm-1). In these data, the aromatic band, probably indicating the presence of polycyclic aromatic hydrocarbons (PAH), is unusually strong in comparison to the aliphatic bands, as was found for Hyperion (Dalton, J.B., Cruikshank, D.P., Clark, R.N. [2012]. Icarus 220, 752-776; Dalle Ore, C.M., Cruikshank

  19. Structural studies of aliphatic substituted phthalocyanine-lipid multilayers.

    PubMed

    Zarbakhsh, Ali; Campana, Mario; Mills, David; Webster, John R P

    2010-10-01

    A Langmuir-Blodgett film of aliphatic substituted phthalocyanines on a C18 silane supporting layer coupled onto a silicon substrate has been investigated using neutron reflectometry. This multilayer structure is seen as a possible candidate for phthalocyanine-lipid biosensor devices. The results show the suitability of the C18 ligands as an anchoring layer for the phthalocyanines. The scattering length density profiles demonstrate the effectiveness of a lipid monolayer in partitioning the composition of phthalocyanine layers from that of the bulk liquid. The effectiveness of this barrier is a critical factor in the efficiency of such devices. PMID:20831252

  20. Decarboxylative Fluorination of Aliphatic Carboxylic Acids via Photoredox Catalysis

    PubMed Central

    Ventre, Sandrine; Petronijevic, Filip R.; MacMillan, David W. C.

    2016-01-01

    The direct conversion of aliphatic carboxylic acids to the corresponding alkyl fluorides has been achieved via visible light-promoted photoredox catalysis. This operationally simple, redox-neutral fluorination method is amenable to a wide variety of carboxylic acids. Photon-induced oxidation of carboxylates leads to the formation of carboxyl radicals, which upon rapid CO2-extrusion and F• transfer from a fluorinating reagent yield the desired fluoroalkanes with high efficiency. Experimental evidence indicates that an oxidative quenching pathway is operable in this broadly applicable fluorination protocol. PMID:25881929

  1. Aliphatic Polyethers: Classical Polymers for the 21st Century.

    PubMed

    Klein, Rebecca; Wurm, Frederik R

    2015-06-01

    Polyethers-polymers with the structural element (R'-O-R)n in their backbone--are an old class of polymers which were already used at the time of the ancient Egyptians. However, still today these materials are highly important with applications in all areas of our life, reaching from the automotive and paper industry to cosmetics and biomedical applications. In this Review, different aliphatic polyethers like poly(epoxide)s, poly(oxetane)s, and poly(tetrahydrofuran) are discussed. Special emphasis is placed on the history, the polymerization techniques (industrially and in academia), the properties, the applications as well as recent developments of these materials. PMID:25967116

  2. Dewaxing by a combination centrifuge/catalytic process including solvent deoiling

    SciTech Connect

    Hafez, M. M.

    1984-10-16

    A hydrocarbon dewaxing process comprising the steps of: (a) chilling the waxy hydrocarbon feed to be dewaxed in the absence of solvent to crystallize a portion of the hard wax; (b) introducing the hydrocarbon feed to be dewaxed into a centrifuge; (c) centrifuging the solvent free hydrocarbon feed thereby generating two streams, stream (I) comprising a major portion of oil with a minor portion of entrained wax, stream (II) comprising a major portion of wax with a minor portion of entrained oil; (d) adding a dewaxing solvent to stream (II) generating a slurry A; (e) feeding slurry A to a centrifuge thereby separating slurry A into an oil-solvent stream (III) and a wax-solvent stream (IV); (f) passing the oil-solvent stream (III) to a membrane separation unit wherein the stream is separated into a recycle solvent stream and an oil-solvent stream of reduced solvent content (stream V); (g) passing oil-solvent stream (V) to an oil recovery unit wherein the stream is separated into a recycle solvent stream and an oil stream (VI); (h) passing the wax-solvent stream (IV) of step (e) to a wax recovery unit wherein the stream is separated into a recycle solvent stream and a recovered wax product stream; (i) combining wax-oil stream (I) of step (c) with oil stream (VI) of step (g) and passing the combined stream to a catalytic dewaxing unit wherein the combined waxy oil stream, in the presence of hydrogen, is contacted with a catalyst and has its wax content reduced, thereby generating a dewaxed oil product stream.

  3. Apparatus for removing hydrocarbon contaminants from solid materials

    DOEpatents

    Bala, G.A.; Thomas, C.P.

    1996-02-13

    A system is described for removing hydrocarbons from solid materials. Contaminated solids are combined with a solvent (preferably terpene based) to produce a mixture. The mixture is washed with water to generate a purified solid product (which is removed from the system) and a drainage product. The drainage product is separated into a first fraction (consisting mostly of contaminated solvent) and a second fraction (containing solids and water). The first fraction is separated into a third fraction (consisting mostly of contaminated solvent) and a fourth fraction (containing residual solids and water). The fourth fraction is combined with the second fraction to produce a sludge which is separated into a fifth fraction (containing water which is ultimately reused) and a sixth fraction (containing solids). The third fraction is then separated into a seventh fraction (consisting of recovered solvent which is ultimately reused) and an eighth fraction (containing hydrocarbon waste). 4 figs.

  4. Method for removing hydrocarbon contaminants from solid materials

    DOEpatents

    Bala, G.A.; Thomas, C.P.

    1995-10-03

    A system is described for removing hydrocarbons from solid materials. Contaminated solids are combined with a solvent (preferably terpene based) to produce a mixture. The mixture is washed with water to generate a purified solid product (which is removed from the system) and a drainage product. The drainage product is separated into a first fraction (consisting mostly of contaminated solvent) and a second fraction (containing solids and water). The first fraction is separated into a third fraction (consisting mostly of contaminated solvent) and a fourth fraction (containing residual solids and water). The fourth fraction is combined with the second fraction to produce a sludge which is separated into a fifth fraction (containing water which is ultimately reused) and a sixth fraction (containing solids). The third fraction is then separated into a seventh fraction (consisting of recovered solvent which is ultimately reused) and an eighth fraction (containing hydrocarbon waste). 4 figs.

  5. Method for removing hydrocarbon contaminants from solid materials

    DOEpatents

    Bala, Gregory A.; Thomas, Charles P.

    1995-01-01

    A system for removing hydrocarbons from solid materials. Contaminated solids are combined with a solvent (preferably terpene based) to produce a mixture. The mixture is washed with water to generate a purified solid product (which is removed from the system) and a drainage product. The drainage product is separated into a first fraction (consisting mostly of contaminated solvent) and a second fraction (containing solids and water). The first fraction is separated into a third fraction (consisting mostly of contaminated solvent) and a fourth fraction (containing residual solids and water). The fourth fraction is combined with the second fraction to produce a sludge which is separated into a fifth fraction (containing water which is ultimately reused) and a sixth fraction (containing solids). The third fraction is then separated into a seventh fraction (consisting of recovered solvent which is ultimately reused) and an eighth fraction (containing hydrocarbon waste).

  6. Apparatus for removing hydrocarbon contaminants from solid materials

    DOEpatents

    Bala, Gregory A.; Thomas, Charles P.

    1996-01-01

    A system for removing hydrocarbons from solid materials. Contaminated solids are combined with a solvent (preferably terpene based) to produce a mixture. The mixture is washed with water to generate a purified solid product (which is removed from the system) and a drainage product. The drainage product is separated into a first fraction (consisting mostly of contaminated solvent) and a second fraction (containing solids and water). The first fraction is separated into a third fraction (consisting mostly of contaminated solvent) and a fourth fraction (containing residual solids and water). The fourth fraction is combined with the second fraction to produce a sludge which is separated into a fifth fraction (containing water which is ultimately reused) and a sixth fraction (containing solids). The third fraction is then separated into a seventh fraction (consisting of recovered solvent which is ultimately reused) and an eighth fraction (containing hydrocarbon waste).

  7. Method for determining asphaltene stability of a hydrocarbon-containing material

    SciTech Connect

    Schabron, John F; Rovani, Jr., Joseph F

    2013-02-05

    A method for determining asphaltene stability in a hydrocarbon-containing material having solvated asphaltenes therein is disclosed. In at least one embodiment, it involves the steps of: (a) precipitating an amount of the asphaltenes from a liquid sample of the hydrocarbon-containing material with an alkane mobile phase solvent in a column; (b) dissolving a first amount and a second amount of the precipitated asphaltenes by changing the alkane mobile phase solvent to a final mobile phase solvent having a solubility parameter that is higher than the alkane mobile phase solvent; (c) monitoring the concentration of eluted fractions from the column; (d) creating a solubility profile of the dissolved asphaltenes in the hydrocarbon-containing material; and (e) determining one or more asphaltene stability parameters of the hydrocarbon-containing material.

  8. How Can We Use Carbon Dioxide as a Solvent?

    ERIC Educational Resources Information Center

    Mohamed, Azmi; Eastoe, Julian

    2011-01-01

    This article describes the work being undertaken to make more use of supercritical carbon dioxide as a green solvent. It discusses how the use of surfactants can address the limitations of supercritical CO[subscript 2] in dissolving solutes that are polar and of higher molecular weight. The design of appropriate hydrocarbon CO[subscript 2]-philic…

  9. Superfund Innovative Technology Evaluation: Demonstration Bulletin: Organic Extraction Utilizing Solvents

    EPA Science Inventory

    This technology utilizes liquified gases as the extracting solvent to remove organics, such as hydrocarbons, oil and grease, from wastewater or contaminated sludges and soils. Carbon dioxide is generally used for aqueous solutions, and propane is used for sediment, sludges and ...

  10. Anthropogenic and biogenic hydrocarbons in soils and vegetation from the South Shetland Islands (Antarctica).

    PubMed

    Cabrerizo, Ana; Tejedo, Pablo; Dachs, Jordi; Benayas, Javier

    2016-11-01

    Two Antarctic expeditions (in 2009 and 2011) were carried out to assess the local and remote anthropogenic sources of aliphatic and aromatic hydrocarbons, as well as potential biogenic hydrocarbons. Polycyclic aromatic hydrocarbons (PAHs), n-alkanes, biomarkers such as phytane (Ph) and pristane (Pr), and the aliphatic unresolved complex mixture (UCM), were analysed in soil and vegetation samples collected at Deception, Livingston, Barrientos and Penguin Islands (South Shetland Islands, Antarctica). Overall, the patterns of n-alkanes in lichens, mosses and grass were dominated by odd-over-even carbon number alkanes. Mosses and vascular plants showed high abundances of n-C21 to n-C35, while lichens also showed high abundances of n-C17 and n-C19. The lipid content was an important factor controlling the concentrations of n-alkanes in Antarctic vegetation (r(2)=0.28-0.53, p-level<0.05). n-C12 to n-C35 n-alkanes were analysed in soils with a predominance of odd C number n-alkanes (n-C25, n-C27, n-C29, and n-C31), especially in the background soils not influenced by anthropogenic sources. The large values for the carbon predominance index (CPI) and the correlations between odd alkanes and some PAHs suggest the potential biogenic sources of these hydrocarbons in Antarctica. Unresolved complex mixture and CPI values ~1 detected at soils collected at intertidal areas and within the perimeter of Juan Carlos research station, further supported the evidence that even a small settlement (20 persons during the austral summer) can affect the loading of aliphatic and aromatic hydrocarbons in nearby soils. Nevertheless, the assessment of Pr/n-C17 and Ph/n-C18 ratios showed that hydrocarbon degradation is occurring in these soils. PMID:27450242

  11. Non-Ideal Behavior in Solvent Extraction

    SciTech Connect

    Peter Zalupski

    2011-09-01

    This report presents a summary of the work performed to meet FCR&D level 3 milestone M31SW050801, 'Complete the year-end report summarizing FY11 experimental and modeling activities.' This work was carried out under the auspices of the Non-Ideality in Solvent Extraction Systems FCR&D work package. The report summarizes our initial considerations of potential influences that non-ideal chemistry may impose on computational prediction of outcomes in solvent extraction systems. The report is packaged into three separate test cases where a robustness of the prediction by SXFIT program is under scrutiny. The computational exercises presented here emphasize the importance of accurate representation of both an aqueous and organic mixtures when modeling liquid-liquid distribution systems. Case No.1 demonstrates that non-ideal behavior of HDEHP in aliphatic diluents, such as n-dodecane, interferes with the computation. Cases No.2 and No.3 focus on the chemical complexity of aqueous electrolyte mixtures. Both exercises stress the need for an improved thermodynamic model of an aqueous environment present in the europium distribution experiments. Our efforts for year 2 of this project will focus on the improvements of aqueous and non-aqueous solution models using fundamental physical properties of mixtures acquired experimentally in our laboratories.

  12. Irresolvable complex mixture of hydrocarbons in soybean oil deodorizer distillate.

    PubMed

    Ju, Yi-Hsu; Huynh, Lien-Huong; Gunawan, Setiyo; Chern, Yaw-Terng; Kasim, Novy S

    2012-01-01

    Aliphatic hydrocarbons (HCs) can be used as a fingerprint of a given seed oil. Only by characterization of aliphatic HCs could contamination by mineral oil in that seed oil be confirmed. During the isolation of squalene from soybean oil deodorizer distillate, a significant amount of unknown HCs, ca. 44 wt%, was obtained. These seemingly-easy-to-identify HCs turned out to be much more difficult to elucidate due to the presence of an irresolvable complex mixture (ICM). The objective of this study was to purify and identify the unknown ICM of aliphatic HCs from soybean oil deodorizer distillate. Purification of the ICM was successfully achieved by using modified Soxhlet extraction, followed by modified preparative column chromatography, and finally by classical preparative column chromatography. FT-IR, TLC, elemental analysis, GC/FID, NMR and GC-MS analyses were then performed on the purified HCs. The GC chromatogram detected the presence of ICM peaks comprising two major peaks and a number of minor peaks. Validation methods such as IR and NMR justified that the unknowns are saturated HCs. This work succeeded in tentatively identifying the two major peaks in the ICM as cycloalkane derivatives. PMID:22162261

  13. Polarized Raman spectra and intensities of aliphatic amino acids

    NASA Astrophysics Data System (ADS)

    Himmler, Hans J.; Eysel, Hans H.

    1989-01-01

    Raman spectra of aliphatic α- L-amino acids, glycine, alanine, and valine were re-investigated both in aqueous solution and deuterium oxide solution. The spectra were taken of the zwitterionic and of the completely deprotonated form of the amino acids. Spectra of leucine and isoleucine were studied in water at the isoelectric point. Spectra were recorded both with parallel and perpendicular polarization and the isotropic and anisotropic scattering components were isolated. The integrated intensities of CH stretch, CC stretch and carboxylate bend vibrations are discussed. Linear relations between the number of CC and CH bonds and the total scattered intensity in the appropriate spectral regions are observed. The sum over the carboxylate modes shows characteristic intensities for the first three members of the aliphatic amino acids. An increase of isotropic scattering of ϱ co 2 near 510 cm -1 with increasing chain length of the amino acid (or with increasing concentration) is interpreted as the result of micelle formation.

  14. Tailoring NO donors metallopharmaceuticals: ruthenium nitrosyl ammines and aliphatic tetraazamacrocycles.

    PubMed

    Tfouni, E; Doro, F G; Figueiredo, L E; Pereira, J C M; Metzker, G; Franco, D W

    2010-01-01

    The discovery of the involvement of nitric oxide (NO) in several physiological and pathophysiological processes launched a spectacular increase in studies in areas such as chemistry, biochemistry, and pharmacology. As a consequence, the development of NO donors or scavengers for regulation of its concentration and bioavailability in vivo is required. In this sense, ruthenium nitrosyl ammines and aliphatic tetraazamacrocyles have attracted a lot of attention due to their unique chemical properties. These complexes are water soluble and stable in solution, not to mention that they can deliver NO when photochemically or chemically activated by the reduction of the coordinated nitrosonium (NO+). The tuning of the energies of the charge transfer bands, the redox potential, and the specific rate constants of NO liberation, in both solution and matrices, is desirable for the achievement of selective NO delivery to biological targets, hence making the ruthenium ammines and aliphatic tetraazamacrocyles a quite versatile platform for biological application purposes. These ruthenium nitrosyls have shown to be active in firing neurons in mouse hippocampus, performing redox reactions in mitochondria, acting in blood pressure control, exhibiting cytotoxic activities against trypanosomatids (T.cruzi and L.major) and tumor cells. This tailoring approach is explored here, being heavily supported by the accumulated knowledge on the chemistry and photochemistry of ruthenium complexes, which allows NO donors/scavengers systems to be custom made designed. PMID:20846113

  15. Terrestrial ecotoxicity of short aliphatic protic ionic liquids.

    PubMed

    Peric, Brezana; Martí, Esther; Sierra, Jordi; Cruañas, Robert; Iglesias, Miguel; Garau, Maria Antonia

    2011-12-01

    A study of the ecotoxicity of different short aliphatic protic ionic liquids (PILs) on terrestrial organisms was conducted. Tests performed within the present study include those assessing the effects of PILs on soil microbial functions (carbon and nitrogen mineralization) and terrestrial plants. The results show that the nominal lowest-observed-adverse-effect concentration (LOAEC) values were 5,000 mg/kg (dry soil) for the plant test in two species (Lolium perenne, Allium cepa), 1,000 mg/kg (dry soil) for the plant test in one species (Raphanus sativus), and 10,000 mg/kg (dry soil) for carbon and nitrogen microbial transformation tests (all concentrations are nominal). Most of the median effective concentration values (EC50) were above 1,000 mg/kg (dry soil). Based on the obtained results, these compounds can be described as nontoxic for soil microbiota and the analyzed plants, and potentially biodegradable in soils, as can be deduced from the respirometric experiment. The toxicity rises with the increase of complexity of the PILs molecule (branch and length of aliphatic chain) among the three PILs analyzed. PMID:21935980

  16. Short-chain aliphatic ester synthesis using Thermobifida fusca cutinase.

    PubMed

    Su, Lingqia; Hong, Ruoyu; Guo, Xiaojie; Wu, Jing; Xia, Yongmei

    2016-09-01

    Short-chain aliphatic esters are commonly used as fruit flavorings in the food industry. In this study, Thermobifida fusca (T. fusca) cutinase was used for the synthesis of aliphatic esters, and the maximum yield of ethyl caproate reached 99.2% at a cutinase concentration of 50U/ml, 40°C, and water content of 0.5%, representing the highest ester yield to date. The cutinase-catalyzed esterification displayed strong tolerance for water content (up to 8%) and acid concentration (up to 0.8M). At substrate concentrations ⩽0.8M, the ester yield remained above 80%. Moreover, ester yields of more than 98% and 95% were achieved for acids of C3-C8 and alcohols of C1-C6, respectively, indicating extensive chain length selectivity of the cutinase. These results demonstrate the superior ability of T. fusca cutinase to catalyze the synthesis of short-chain esters. This study provides the basis for industrial production of short-chain esters using T. fusca cutinase. PMID:27041308

  17. Kinetics of bacterial growth on chlorinated aliphatic compounds

    SciTech Connect

    Wijngaard, A.J. van den; Wind, R.E.; Janssen, D.B. )

    1993-07-01

    Halogenated aliphatic compounds are frequent constituents of industrial waste gases. Because of the environmental and biological toxic effects of these compounds, there is a growing interest in technologies for their removal. Biological waste gas purification is an option if specialized bacterial strains that use halogenated aliphatics as sole carbon and energy sources can be used. Elimination efficiency of the compounds depends not only on the process technology but on the degradation properties of the bacterial strains. Important aspects of bacterial growth are the Monod half-saturation constant and the maximum growth rate. In this study the kinetic properties of the organisms (Ancylobacter aquaticus AD20 and AD25, Xanthobacter autotrophicus GJ10, Pseudomonas sp. strain AD1) weree measured during growth in continuous cultures and wer compared with the kinetic properties of the first catabolic enzyme involved in the degradation of the growth substrate. The results indicate that the growth of the strains examined followed Monod kinetics. Stains AD20 and GJ10 showed growth rates on DCE somewhat higher than predicted from the amount of haloalkane dehalogenase present in the cells, while strain AD25 was much lower. 33 refs., 3 figs., 4 tabs.

  18. Radiation induced dechlorination of some chlorinated hydrocarbons in aqueous suspensions of various solid particles

    NASA Astrophysics Data System (ADS)

    Múčka, V.; Buňata, M.; Čuba, V.; Silber, R.; Juha, L.

    2015-07-01

    Radiation induced dechlorination of trichloroethylene (TCE) and tetrachloroethylene (PCE) in aqueous solutions containing the active carbon (AC) or cupric oxide (CuO) as the modifiers was studied. The obtained results were compared to the previously studied dechlorination of polychlorinated biphenyls (PCBs). Both modifiers were found to decrease the efficiency of dechlorination. The AC modifier acts mainly via adsorption of the aliphatic (unlike the aromatic) hydrocarbons and the CuO oxide mainly inhibits the mineralization of the perchloroethylene. The results presented in this paper will be also helpful for the studies of the impact of chlorinated hydrocarbons on the membrane permeability of living cells.

  19. UV-Screening Strategies of a Lower Eukaryote Grown in Hydrocarbon Media

    NASA Astrophysics Data System (ADS)

    Marcano, Vicente; Benitez, Pedro; Palacios-Prü, Ernesto

    2006-02-01

    In this paper, a detailed analysis of the UV-screening strategies of the fungus Fusarium alkanophyllum is offered using spectroscopic (UV-VIS, FTIR), chromatographic (TLC, HPLC) and physiological analysis methods. Fusarium alkanophyllum showed an optimum growth when exposed to UV radiation at 253.7 (inducing DNA and protein damages) or 354.5 nm (inducing photoxidative damage) in several hydrocarbon media. Further, no ultrastructural difference was seen when cultures were or not irradiated with monochromatic UV. High absorbance between 200 300 nm of F. alkanophyllum indole derivatives, viz. melanin-type pigments, suggests a protector effect for proteins and nucleic acids. The presence of sulfur linked to aliphatic groups in hydrocarbons which is itself a strong UV absorber in the region of λ < 270 nm can explain why mineral oil and kerosene showed high absorptivity at the UVC and UVB ranges. In light hydrocarbon, high absorptivities at the UVB and UVA spectral regions could be explained due to the presence of C O stretching vibrations corresponding to ketones linked to aliphatic groups. The occurrence of indole derivatives in modern fungi may be a significant relic of the early evolution of microbial pigmentation. Likewise, it is thought that sulfur-enriched heterogeneous hydrocarbon environments could have occurred on the surface of the early Earth and could have absorbed and scattered UV-radiation avoiding or minimizing the damage produced on the biochemical machinery of early microorganisms able to metabolize those hydrocarbons.

  20. Hydrocarbons on Saturns Satellites: Relationship to Interstellar Dust and the Solar Nebula

    NASA Technical Reports Server (NTRS)

    Cruikshank, D. P.

    2012-01-01

    To understand the origin and evolution of our Solar System, and the basic components that led to life on Earth, we study interstellar and planetary spectroscopic signatures. The possible relationship of organic material detected in carbonaceous meteorites, interplanetary dust particles (IDPs), comets and the interstellar medium have been the source of speculation over the years as the composition and processes that governed the early solar nebula have been explored to understand the extent to which primitive material survived or became processed. The Cassini VIMS has provided new data relevant to this problem. Three of Saturn's satellites, Phoebe, Iapetus, and Hyperion, are found to have aromatic and aliphatic hydrocarbons on their surfaces. The aromatic hydrocarbon signature (C-H stretching mode at 3.28 micrometers) is proportionally significantly stronger (relative to the aliphatic bands) than that seen in other Solar System bodies (e.g., comets) and materials (Stardust samples, IDPs, meteorites) and the distinctive sub-features of the 3.4 micrometer aliphatic band (CH2 and CH3 groups) are reminiscent of those widely detected throughout the diffuse ISM. Phoebe may be a captured object that originated in the region beyond the present orbit of Neptune, where the solar nebula contained a large fraction of original interstellar ice and dust that was less processed than material closer to the Sun. Debris from Phoebe now resident on Iapetus and Hyperion, as well as o Phoebe itself, thus presents a unique blend of hydrocarbons, amenable to comparisons with interstellar hydrocarbons and other Solar System materials. The dust ring surrounding Saturn, in which Phoebe is embedded, probably originated from a collision with Phoebe. Dust ring particles are the likely source of the organic-bearing materials, and perhaps the recently identified small particles of Fe detected on Saturn's satellites. Lab measurements of the absolute band strengths of representative aliphatic and

  1. Features of hydrocarbon distribution in the coastal zone of the northeastern Black Sea

    NASA Astrophysics Data System (ADS)

    Nemirovskaya, I. A.; Onegina, V. D.; Konovalov, B. V.

    2015-09-01

    Data on the content and composition of aliphatic and polycyclic aromatic hydrocarbons in surface water and bottom sediments are reported as compared to the distribution of total organic carbon, suspended particulate matter, lipids, and chlorophyll for the Greater Sochi area and the Gelendzhik and Blue bays. It is established that an influx of oil products leads to the increase of hydrocarbon concentrations in the water and bottom sediments, thus providing the present-day hydrocarbon background. Active transformation of organic matter in the water succession and on the water-bottom interface results in the prevalence of natural components in alkanes in spite of the high hydrocarbon concentrations (119-262 μg/g). The river-seawater mixing zone serves as a geochemical barrier preventing the influx of most pollutants delivered by rivers into open sea.

  2. 40 CFR 721.7250 - Polyaziridinyl ester of an aliphatic alcohol (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... alcohol (generic). 721.7250 Section 721.7250 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.7250 Polyaziridinyl ester of an aliphatic alcohol (generic). (a... generically as a polyaziridinyl ester of an aliphatic alcohol (PMN P-01-97) is subject to reporting under...

  3. 40 CFR 721.7250 - Polyaziridinyl ester of an aliphatic alcohol (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... alcohol (generic). 721.7250 Section 721.7250 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.7250 Polyaziridinyl ester of an aliphatic alcohol (generic). (a... generically as a polyaziridinyl ester of an aliphatic alcohol (PMN P-01-97) is subject to reporting under...

  4. 40 CFR 721.7250 - Polyaziridinyl ester of an aliphatic alcohol (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... alcohol (generic). 721.7250 Section 721.7250 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.7250 Polyaziridinyl ester of an aliphatic alcohol (generic). (a... generically as a polyaziridinyl ester of an aliphatic alcohol (PMN P-01-97) is subject to reporting under...

  5. 40 CFR 721.7250 - Polyaziridinyl ester of an aliphatic alcohol (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... alcohol (generic). 721.7250 Section 721.7250 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.7250 Polyaziridinyl ester of an aliphatic alcohol (generic). (a... generically as a polyaziridinyl ester of an aliphatic alcohol (PMN P-01-97) is subject to reporting under...

  6. 40 CFR 721.9952 - Alkoxylated aliphatic diisocyanate allyl ether (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... allyl ether (generic). 721.9952 Section 721.9952 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.9952 Alkoxylated aliphatic diisocyanate allyl ether... identified generically as alkoxylated aliphatic diisocyanate allyl ether (PMN P-00-0353) is subject...

  7. 40 CFR 721.9952 - Alkoxylated aliphatic diisocyanate allyl ether (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... allyl ether (generic). 721.9952 Section 721.9952 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.9952 Alkoxylated aliphatic diisocyanate allyl ether... identified generically as alkoxylated aliphatic diisocyanate allyl ether (PMN P-00-0353) is subject...

  8. 40 CFR 721.2098 - Aliphatic polycarboxylic acid metal salt (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... (CONTINUED) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.2098 Aliphatic polycarboxylic acid metal salt (generic). (a) Chemical... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Aliphatic polycarboxylic acid...

  9. 40 CFR 721.10606 - Alkyl substituted alkanediol polymer with aliphatic and alicyclic diisocyanates (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Alkyl substituted alkanediol polymer... alkanediol polymer with aliphatic and alicyclic diisocyanates (generic). (a) Chemical substance and... substituted alkanediol polymer with aliphatic and alicyclic diisocyanates (PMN P-11-486) is subject...

  10. 40 CFR 721.10605 - Polyoxyalkylene ether, polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Polyoxyalkylene ether, polymer with..., polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (generic). (a) Chemical substance and... polyoxyalkylene ether, polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (PMN P-11-485) is...

  11. 40 CFR 721.10605 - Polyoxyalkylene ether, polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Polyoxyalkylene ether, polymer with..., polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (generic). (a) Chemical substance and... polyoxyalkylene ether, polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (PMN P-11-485) is...

  12. 40 CFR 721.10606 - Alkyl substituted alkanediol polymer with aliphatic and alicyclic diisocyanates (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Alkyl substituted alkanediol polymer... alkanediol polymer with aliphatic and alicyclic diisocyanates (generic). (a) Chemical substance and... substituted alkanediol polymer with aliphatic and alicyclic diisocyanates (PMN P-11-486) is subject...

  13. 40 CFR 721.2098 - Aliphatic polycarboxylic acid metal salt (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... salt (generic). 721.2098 Section 721.2098 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.2098 Aliphatic polycarboxylic acid metal salt (generic). (a) Chemical... as an aliphatic polycarboxylic acid metal salt (PMN P-01-7) is subject to reporting under...

  14. 40 CFR 721.2098 - Aliphatic polycarboxylic acid metal salt (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... salt (generic). 721.2098 Section 721.2098 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.2098 Aliphatic polycarboxylic acid metal salt (generic). (a) Chemical... as an aliphatic polycarboxylic acid metal salt (PMN P-01-7) is subject to reporting under...

  15. 40 CFR 721.2098 - Aliphatic polycarboxylic acid metal salt (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... salt (generic). 721.2098 Section 721.2098 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.2098 Aliphatic polycarboxylic acid metal salt (generic). (a) Chemical... as an aliphatic polycarboxylic acid metal salt (PMN P-01-7) is subject to reporting under...

  16. 40 CFR 721.2098 - Aliphatic polycarboxylic acid metal salt (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... salt (generic). 721.2098 Section 721.2098 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.2098 Aliphatic polycarboxylic acid metal salt (generic). (a) Chemical... as an aliphatic polycarboxylic acid metal salt (PMN P-01-7) is subject to reporting under...

  17. Solvent extraction process

    SciTech Connect

    Woodle, R.A.

    1982-01-19

    A solvent refining process is disclosed utilizing n-methyl-2-pyrrolidone as solvent in which primary extract from the extraction zone is cooled to form a secondary raffinate and secondary extract and the secondary and primary raffinates are blended to produce an increased yield of product of desired quality. In a preferred embodiment of the process, the lubricating oil feedstock to the process is first contacted with a stripping medium previously used in the process for the recovery of solvent from at least one of the product streams whereby solvent contained in said stripping medium is recovered therefrom.

  18. Effect on de-greasing solvents on conductive separable connector shields and semiconductive cable shields

    SciTech Connect

    Perry, D.D.; Bolcar, J.P. . Elastimold Div.)

    1990-04-01

    A study has been conducted to determine the effects of commercial degreasing solvents on the conductivity of an EPDM separable connector shield and two types of cable shields based on EPR and XLPE, respectively. Solvents tested included a chlorinated solvent based on 1,1,1-trichloroethane and several so-called citrus solvents consisting of the natural terpene, limonene, or blends of limonene with other hydrocarbons. All the solvents significantly degraded the conductivity of the EPR and EPDM materials, but had little effect on the XLPE cable shield. The solvents differed, however, in the extent of their effects, the rate of recovery of conductivity after removal of the solvent, and the degree to which the original conductivity of the material was restored. The consequences of these results in terms of appropriate field use of these types of solvents by utility personnel are discussed.

  19. Extraction Techniques for Polycyclic Aromatic Hydrocarbons in Soils

    PubMed Central

    Lau, E. V.; Gan, S.; Ng, H. K.

    2010-01-01

    This paper aims to provide a review of the analytical extraction techniques for polycyclic aromatic hydrocarbons (PAHs) in soils. The extraction technologies described here include Soxhlet extraction, ultrasonic and mechanical agitation, accelerated solvent extraction, supercritical and subcritical fluid extraction, microwave-assisted extraction, solid phase extraction and microextraction, thermal desorption and flash pyrolysis, as well as fluidised-bed extraction. The influencing factors in the extraction of PAHs from soil such as temperature, type of solvent, soil moisture, and other soil characteristics are also discussed. The paper concludes with a review of the models used to describe the kinetics of PAH desorption from soils during solvent extraction. PMID:20396670

  20. The Impact of the Absence of Aliphatic Glucosinolates on Insect Herbivory in Arabidopsis

    PubMed Central

    van Dam, Nicole M.; Bertossi, Monica; Grandi, Valentina; Mizzi, Luca; Soloviev, Mikhail; Szabados, Laszlo; Molthoff, Jos W.; Schipper, Bert; Verbocht, Hans; de Vos, Ric C. H.; Morandini, Piero; Aarts, Mark G. M.; Bovy, Arnaud

    2008-01-01

    Aliphatic glucosinolates are compounds which occur in high concentrations in Arabidopsis thaliana and other Brassicaceae species. They are important for the resistance of the plant to pest insects. Previously, the biosynthesis of these compounds was shown to be regulated by transcription factors MYB28 and MYB29. We now show that MYB28 and MYB29 are partially redundant, but in the absence of both, the synthesis of all aliphatic glucosinolates is blocked. Untargeted and targeted biochemical analyses of leaf metabolites showed that differences between single and double knock-out mutants and wild type plants were restricted to glucosinolates. Biosynthesis of long-chain aliphatic glucosinolates was blocked by the myb28 mutation, while short-chain aliphatic glucosinolates were reduced by about 50% in both the myb28 and the myb29 single mutants. Most remarkably, all aliphatic glucosinolates were completely absent in the double mutant. Expression of glucosinolate biosynthetic genes was slightly but significantly reduced by the single myb mutations, while the double mutation resulted in a drastic decrease in expression of these genes. Since the myb28myb29 double mutant is the first Arabidopsis genotype without any aliphatic glucosinolates, we used it to establish the relevance of aliphatic glucosinolate biosynthesis to herbivory by larvae of the lepidopteran insect Mamestra brassicae. Plant damage correlated inversely to the levels of aliphatic glucosinolates observed in those plants: Larval weight gain was 2.6 fold higher on the double myb28myb29 mutant completely lacking aliphatic glucosinolates and 1.8 higher on the single mutants with intermediate levels of aliphatic glucosinolates compared to wild type plants. PMID:18446225

  1. The spark discharge synthesis of amino acids from various hydrocarbons

    NASA Technical Reports Server (NTRS)

    Ring, D.; Miller, S. L.

    1984-01-01

    The spark discharge synthesis of amino acids using an atmosphere of CH4+N2+H2O+NH3 has been investigated with variable pNH3. The amino acids produced using higher hydrocarbons (ethane, ethylene, acetylene, propane, butane, and isobutane) instead of CH4 were also investigated. There was considerable range in the absolute yields of amino acids, but the yields relative to glycine (or alpha-amino-n-butyric acid) were more uniform. The relative yields of the C3 to C6 aliphatic alpha-amino acids are nearly the same (with a few exceptions) with all the hydrocarbons. The glycine yields are more variable. The precursors to the C3-C6 aliphatic amino acids seem to be produced in the same process, which is separate from the synthesis of glycine precursors. It may be possible to use these relative yields as a signature for a spark discharge synthesis provided corrections can be made for subsequent decomposition events (e.g. in the Murchison meteorite).

  2. Aqueous infrared carboxylate absorbances: Aliphatic di-acids

    USGS Publications Warehouse

    Cabaniss, S.E.; Leenheer, J.A.; McVey, I.F.

    1998-01-01

    Aqueous attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectra of 18 aliphatic di-carboxylic acids are reported as a function of pH. The spectra show isosbestic points and intensity changes which indicate that Beer's law is obeyed, and peak frequencies lie within previously reported ranges for aqueous carboxylates and pure carboxylic acids. Intensity sharing from the symmetric carboxylate stretch is evident in many cases, so that bands which are nominally due to alkyl groups show increased intensity at higher pH. The asymmetric stretch of the HA- species is linearly related to the microscopic acidity constant of the H2A species, with ??pK 2 intervening atoms). The results suggest that aqueous ATR-FTIR may be able to estimate 'intrinsic' pKa values of carboxylic acids, in addition to providing quantitative estimates of ionization. ?? 1998 Elsevier Science B.V. All rights reserved.

  3. Solid-phase microextraction of hydrocarbons from water in a centrifuge

    NASA Astrophysics Data System (ADS)

    Ryabov, A. Yu.; Chuikin, A. V.; Velikov, A. A.

    2016-06-01

    The results of our study of solid-phase microextraction of substances using a centrifuge for determining the microquantities of hydrocarbon impurities in water are presented. The cartridge diameter, sorbent mass, and solvent volume were shown to affect the percent extraction of substances and the analytical signal intensity. The relationship between the cartridge geometry, the sorbent mass, and the solvent volume was considered.

  4. SOLVENT EXTRACTION OF NEPTUNIUM

    DOEpatents

    Butler, J.P.

    1958-08-12

    A process is described for the recovery of neptuniunn from dissolver solutions by solvent extraction. The neptunium containing solution should be about 5N, in nitric acid.and about 0.1 M in ferrous ion. The organic extracting agent is tributyl phosphate, and the neptuniunn is recovered from the organic solvent phase by washing with water.

  5. ONSITE SOLVENT RECOVERY

    EPA Science Inventory

    This study evaluated the product quality, waste reduction/pollution prevention, and economic aspects of three technologies for onsite solvent recovery: atmospheric batch distillation, vacuum heat-pump distillation, and a low-emission vapor degreaser with closed solvent, liquid an...

  6. Solvent-free synthesis

    EPA Science Inventory

    This chapter gives a brief introduction about solvent-free reactions whose importance can be gauged by the increasing number of publications every year during the last decade. The mechanistic aspects of the reactions under solvent-free conditions have been highlighted. Our observ...

  7. Sodium hypochlorite oxidation of petroleum aliphatic contaminants in calcareous soils.

    PubMed

    Picard, François; Chaouki, Jamal

    2016-02-01

    This research project investigated the sodium hypochlorite (NaClO) oxidation of aliphatic petroleum contaminants (C10-C50) in a calcareous soil (average 5473 ppm C10-C50, 15 wt% Ca), which had been excavated from a contaminated industrial site. The decontamination objective was to lower the C10-C50 concentration to 700 ppm. CO2 acidity was used in the project to boost the NaClO oxidation yield and seems to have played a role in desorbing the natural organic matter. The experimental conditions were a 2- to 16-h reaction time, at room temperature, with a 1 to 12.5 wt% NaClO oxidative solution and a fixed 2:1 solution-to-soil ratio. With a 3 wt% NaClO solution and with a CO2 overhead, the NaClO dosage requirement was maintained below 60 g NaClO/g of oxidized C10-C50 over the entire decontamination range. The strong chlorine smell remaining after the reaction was completed suggests that part of the NaClO requirement can be recycled. Except traces of chloroform, there were no regulation-listed organochloride contaminants detected on either the treated soil samples or leachates and the total count of chlorinated compounds in treated soil samples was below the detection limit of 250 mg/kg. The NaClO oxidation mechanism on aliphatic substrates might be triggered by transition metals, such as manganese, but no attempt has been made to investigate the oxidation mechanism. Further investigations would include a constant-fed NaClO system and other techniques to lower the required NaClO dosage. PMID:26702553

  8. Natural and anthropogenic hydrocarbon inputs to sediments of Patos Lagoon Estuary, Brazil.

    PubMed

    Medeiros, Patricia Matheus; Bícego, Márcia Caruso; Castelao, Renato Menezes; Del Rosso, Clarissa; Fillmann, Gilberto; Zamboni, Ademilson Josemar

    2005-01-01

    The Patos Lagoon Estuary, southern Brazil, is an area of environmental interest not only because of tourism, but also because of the presence of the second major port of Brazil, with the related industrial and shipping activities. Thus, potential hydrocarbon pollution was examined in this study. Sediment samples were collected at 10 sites in the estuary, extracted, and analyzed by GC-FID and GC-MS for composition and concentration of the following organic geochemical markers: normal and isoprenoid alkanes, petroleum biomarkers, linear alkylbenzenes (LABs), and polycyclic aromatic hydrocarbons (PAHs). The total concentrations varied from 1.1 to 129.6 microg g(-1) for aliphatic hydrocarbons, from 17.8 to 4510.6 ng g(-1) for petroleum biomarkers, from 3.2 to 1601.9 ng g(-1) for LABs, and from 37.7 to 11,779.9 ng g(-1) for PAHs. Natural hydrocarbons were mainly derived from planktonic inputs due to a usual development of blooms in the estuary. Terrestrial plant wax compounds prevailed at sites located far from Rio Grande City and subject to stronger currents. Anthropogenic hydrocarbons are related to combustion/pyrolysis processes of fossil fuel, release of unburned oil products and domestic/industrial waste outfalls. Anthropogenic hydrocarbon inputs were more apparent at sites associated with industrial discharges (petroleum distributor and refinery), shipping activities (dry docking), and sewage outfalls (sewage). The overall concentrations of anthropogenic hydrocarbons revealed moderate to high hydrocarbon pollution in the study area. PMID:15607781

  9. Use of once-through treat gas to remove the heat of reaction in solvent hydrogenation processes

    DOEpatents

    Nizamoff, Alan J.

    1980-01-01

    In a coal liquefaction process wherein feed coal is contacted with molecular hydrogen and a hydrogen-donor solvent in a liquefaction zone to form coal liquids and vapors and coal liquids in the solvent boiling range are thereafter hydrogenated to produce recycle solvent and liquid products, the improvement which comprises separating the effluent from the liquefaction zone into a hot vapor stream and a liquid stream; cooling the entire hot vapor stream sufficiently to condense vaporized liquid hydrocarbons; separating condensed liquid hydrocarbons from the cooled vapor; fractionating the liquid stream to produce coal liquids in the solvent boiling range; dividing the cooled vapor into at least two streams; passing the cooling vapors from one of the streams, the coal liquids in the solvent boiling range, and makeup hydrogen to a solvent hydrogenation zone, catalytically hydrogenating the coal liquids in the solvent boiling range and quenching the hydrogenation zone with cooled vapors from the other cooled vapor stream.

  10. Tailoring hydrocarbon streams for asphaltene removal

    SciTech Connect

    Del Bianco, A.; Stroppa, F.; Bertero, L.

    1995-11-01

    Oilfield production is often hindered by asphaltene precipitation which tends to fill the pores of the reservoir rocks and plug the wellbore tubing as well as the other auxiliary equipment used during crude oil recovery. Several remedies to remove these deposits have been proposed and patented but the injection of aromatic solvents such as toluene and light petroleum distillates is normally preferred. Previous studies with a number of pure aromatic hydrocarbons have shown that the solvent capacity of these molecules may be very different and that the degree of condensation plays an important role. In this regard, tetralins and naphthalenes are superior to alkylbenzenes. However, because the use of pure compounds is not economically feasible, the authors examined various industrial streams and the authors correlated their chemical composition to the solvent capacity. This work allowed the identification of the pseudo-components whose relative concentration is crucial for evaluating the solvent performances. Based on these data, the authors were able to find new products with ideal characteristics. The efficiency of one of these products was confirmed by the analysis of the data obtained when using this new solvent to remove asphaltene in damaged wells of an Italian field.

  11. Green Solvents for Precision Cleaning

    NASA Technical Reports Server (NTRS)

    Grandelli, Heather; Maloney, Phillip; DeVor, Robert; Surma, Jan; Hintze, Paul

    2013-01-01

    Aerospace machinery used in liquid oxygen (LOX) fuel systems must be precision cleaned to achieve a very low level of non-volatile residue (< 1 mg0.1 m2), especially flammable residue. Traditionally chlorofluorocarbons (CFCs) have been used in the precision cleaning of LOX systems, specifically CFC 113 (C2Cl3F3). CFCs have been known to cause the depletion of ozone and in 1987, were banned by the Montreal Protocol due to health, safety and environmental concerns. This has now led to the development of new processes in the precision cleaning of aerospace components. An ideal solvent-replacement is non-flammable, environmentally benign, non-corrosive, inexpensive, effective and evaporates completely, leaving no residue. Highlighted is a green precision cleaning process, which is contaminant removal using supercritical carbon dioxide as the environmentally benign solvent. In this process, the contaminant is dissolved in carbon dioxide, and the parts are recovered at the end of the cleaning process completely dry and ready for use. Typical contaminants of aerospace components include hydrocarbon greases, hydraulic fluids, silicone fluids and greases, fluorocarbon fluids and greases and fingerprint oil. Metallic aerospace components range from small nuts and bolts to much larger parts, such as butterfly valves 18 in diameter. A fluorinated grease, Krytox, is investigated as a model contaminant in these preliminary studies, and aluminum coupons are employed as a model aerospace component. Preliminary studies are presented in which the experimental parameters are optimized for removal of Krytox from aluminum coupons in a stirred-batch process. The experimental conditions investigated are temperature, pressure, exposure time and impeller speed. Temperatures of 308 - 423 K, pressures in the range of 8.3 - 41.4 MPa, exposure times between 5 - 60 min and impeller speeds of 0 - 1000 rpm were investigated. Preliminary results showed up to 86 cleaning efficiency with the

  12. Combustion of viscous hydrocarbons

    SciTech Connect

    Hayes, M.E.; Hrebenar, K.R.; Murphy, P.L.; Futch, L.E. Jr.; Deal, J.F. III; Bolden, P.L. Jr.

    1987-08-04

    A method is described for utilizing viscous hydrocarbons as combustible pre-atomized fuels, comprising: (A) forming a hydrocarbon-in-water emulsion using an effective amount of a surfactant package comprising at least one water-soluble surfactant, the hydrocarbon-in-water emulsion (1) comprising a hydrocarbon characterized by API gravity of about 20/sup 0/ API or less, viscosity of about 1000 centipoise or greater at 212/sup 0/F., a paraffin content of about 50% by weight or less and, an aromatic content of about 15% by weight or greater, and (2) having a hydrocarbon water ratio from about 60:40 to about 90:10 by volume; and (B) burning the resultant hydrocarbon-in-water emulsion.

  13. SOLVENT EXTRACTION PROCESS

    DOEpatents

    Jonke, A.A.

    1957-10-01

    In improved solvent extraction process is described for the extraction of metal values from highly dilute aqueous solutions. The process comprises contacting an aqueous solution with an organic substantially water-immiscible solvent, whereby metal values are taken up by a solvent extract phase; scrubbing the solvent extract phase with an aqueous scrubbing solution; separating an aqueous solution from the scrubbed solvent extract phase; and contacting the scrubbed solvent phase with an aqueous medium whereby the extracted metal values are removed from the solvent phase and taken up by said medium to form a strip solution containing said metal values, the aqueous scrubbing solution being a mixture of strip solution and an aqueous solution which contains mineral acids anions and is free of the metal values. The process is particularly effective for purifying uranium, where one starts with impure aqueous uranyl nitrate, extracts with tributyl phosphate dissolved in carbon tetrachloride, scrubs with aqueous nitric acid and employs water to strip the uranium from the scrubbed organic phase.

  14. Influence of Other Contaminants on Natural Attenuation of Chlorinated Solvents

    SciTech Connect

    Kinsall, B.L.; Palumbo, A.V.; Pfiffner, S.M.; Phelps, T.J.; Salpas, P.

    1999-04-19

    Studies at numerous sites have shown high variability in the degradation rates of chlorinated solvents as measured by microcosm studies with 14C labeled contaminants. The ability of nutrient and carbon additions to stimulate degradation can vary widely. Although some of these variations can be related to the structure of the extant microbial community, the presence of other less refractory contaminants may be critical fctors impacting the rate of chlorocarbon mineralization. Relaatively highe rates of TCE degradation have been observed in the DOE K-25 burial grounds with diverse organic loadings as well as in areas that show evidence for hydrocarbon contamination. Similarly, at other sites where there was TCE in the absence of hydrocarbons or other contaminants, the measured degradation rates have often been found to be very low. At various other sites, the intrasite variability in degradation rates appeared to be related to the presence of hydrocarbon contamination. The highest rates were observed at sites with evidence of hydrocarbons. These observations indicated that the viability of natural attenuation as a remediation option for chlorinated solvents might depend in part on the presence co-contaminants such as hydrocarbons or natural matter.

  15. Suberin-derived aliphatic monomers as biomarkers for SOM affected by root litter contribution

    NASA Astrophysics Data System (ADS)

    Kogel-Knabner, I.; Spielvogel, S.-; Prietzel, J.-

    2012-12-01

    The patchy distribution of trees and ground vegetation may have major impact on SOC variability and stability at the small scale. Knowledge about correlations between the pattern of tree and ground vegetation, SOC stocks in different soil depths and the contribution of root- vs. shoot-derived carbon to different SOC fractions is scarce. We have tested analysis of hydrolysable aliphatic monomers derived from the biopolyesters cutin- and suberin to investigate whether their composition can be traced back after decay and transformation into soil organic matter (SOM) to study SOM source, degradation, and stand history. The main objective of this study was to elucidate the relative abundance of cutin and suberin in different particle size and density fractions of a Norway spruce and a European beech site with increasing distance to stems. Soil samples, root, bark and needle/leave samples were analyzed for their cutin and/or suberin signature. Previous to isolation of bound lipids, sequential solvent extraction was used to remove free lipids and other solvent extractable compounds. Cutin- and suberin-derived monomers were extracted from the samples using base hydrolysis. Before analysis by Gas Chromatography/Mass Spectrometry (GC/MS), extracts were derivatized to convert compounds to trimethylsilyl derivatives. Statistical analysis identified four variables which as combined factors discriminated significantly between cutin and suberin based on their structural units. We found a relative enrichment of cutin and suberin contents in the occluded fraction at both sites that decreased with increasing distance to the trees. We conclude from our results that (i) patchy above- and belowground carbon input caused by heterogeneous distribution of trees and ground vegetation has major impact on SOC variability and stability at the small scale, (ii) tree species is an important factor influencing SOC heterogeneity at the stand scale due to pronounced differences in above- and

  16. Solvent alternatives guide

    SciTech Connect

    Elion, J.M.; Monroe, K.R.; Hill, E.A.

    1996-06-01

    It is no longer legal to manufacture or import chlorofluorocarbon 113 or methyl chloroform solvents, and companies that currently clean their parts with either material are now required to implement environmentally safe substitutes. To help find alternative methods, Research Triangle Institute`s Surface Cleaning Technology Program has designed a Solvent Alternatives Guide (SAGE), an online tool that enables access to practical information and recommendations for acceptable solvents. Developed in partnership with the US Environmental Protection Agency, SAGE is available free of charge on the Internet`s World Wide Web.

  17. Distribution and Sources of Petroleum Hydrocarbons in Recent Sediments of the Imo River, SE Nigeria.

    PubMed

    Oyo-Ita, Inyang O; Oyo-Ita, Orok E; Dosunmu, Miranda I; Domínguez, Carmen; Bayona, Josep M; Albaigés, Joan

    2016-02-01

    The distribution of aliphatic and aromatic hydrocarbons in surface sediments of the lower course of the Imo River (Nigeria) was investigated to determine the sources and fate of these compounds. The aliphatic fraction is characterized by a widespread contribution of highly weathered/biodegraded hydrocarbon residues (reflected in the absence of prominent n-alkane peaks coupled with the presence of 17α(H),21β(H)-25-norhopane, an indicator of heavy hydrocarbon biodegradation) of Nigerian crude oils (confirmed by the occurrence of 18α(H)-oleanane, a compound characteristic of oils of deltaic origin). The concentrations of polycyclic aromatic hydrocarbons (PAHs) ranging from 48 to 117 ng/g dry weight (dw; ∑13PAHs) indicate a moderate pollution, possibly lowered by the sandy lithology and low organic carbon (OC) content of the sediments. Concentrations slightly decrease towards the estuary of the river, probably due to the fact that these stations are affected by tidal flushing of pollutants adsorbed on sediment particles and carried away by occasional storm to the Atlantic Ocean. A number of PAH ratios, including parent/alkylated and isomeric compounds, indicates a predominance of petrogenic sources, with a low contribution of pyrolytic inputs, particularly of fossil fuel combustion. On the basis of OC/ON (>10) and Per/ΣPAHpenta- (>10) values, a diagenetic terrigenous OC was proposed as a source of perylene to the river. PMID:26546420

  18. Hydrocarbons, PCBs and DDT in the NW Mediterranean deep-sea fish Mora moro

    NASA Astrophysics Data System (ADS)

    Solé, Montserrat; Porte, Cinta; Albaigés, Joan

    2001-02-01

    Data on aliphatic and polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs) and DDTs in the deep-sea fish Mora moro are reported in relation to the animal's weight/size and tissues (muscle, liver, digestive tube and gills). Fish samples were collected in the Gulf of Lions (NW Mediterranean) at an approximate depth of 1000 m. The concentrations of these organic pollutants followed the trend muscleHydrocarbons, and particularly PAHs, were strongly depleted in all tissues with respect to organochlorinated compounds if compared with the amounts present in bottom waters and sediment. Smaller specimens displayed for most pollutants qualitatively different patterns than larger fish, which could be attributed to their particular habitat/diet. The aliphatic hydrocarbon profiles suggested that Mora moro was exposed to a more predominant intake of biogenic rather than petrogenic hydrocarbons. The entrance and storage organs exhibited characteristic PAH and PCB distributions, reflecting different bioaccumulation and metabolic pathways. Compared with the profiles currently found in surface fish species, a relatively higher contribution of heavier components, namely hepta- and octochlorinated PCBs, and 4-6-ringed PAHs, was found in the deep-sea fish.

  19. New insight on aliphatic linkages in the macromolecular organic fraction of Orgueil and Murchison meteorites through ruthenium tetroxide oxidation

    NASA Astrophysics Data System (ADS)

    Remusat, Laurent; Derenne, Sylvie; Robert, François

    2005-09-01

    Ruthenium tetroxide oxidation was used to examine the macromolecular insoluble organic matter (IOM) from the Orgueil and Murchison meteorites and especially to characterize the aliphatic linkages. Already applied to various terrestrial samples, ruthenium tetroxide is a selective oxidant which destroys aromatic units, converting them into CO 2, and yields aliphatic and aromatic acids. In our experiment on chondritic IOM, it produces mainly short aliphatic diacids and polycarboxylic aromatic acids. Some short hydroxyacids are also detected. Aliphatic diacids are interpreted as aliphatic bridges between aromatic units in the chemical structure, and polycarboxylic aromatic acids are the result of the fusion of polyaromatic units. The product distribution shows that aliphatic links are short with numerous substitutions. No indigenous monocarboxylic acid was detected, showing that free aliphatic chains must be very short (less than three carbon atoms). The hydroxyacids are related to the occurrence of ester and ether functional groups within the aliphatic bridges between the aromatic units. This technique thus allows us to characterize in detail the aliphatic linkages of the IOMs, and the derived conclusions are in agreement with spectroscopic, pyrolytic, and degradative results previously reported. Compared to terrestrial samples, the aliphatic part of chondritic IOM is shorter and highly substituted. Aromatic units are smaller and more cross-linked than in coals, as already proposed from NMR data. Orgueil and Murchison IOM exhibit some tiny differences, especially in the length of aliphatic chains.

  20. CHLORINATED SOLVENT PLUME CONTROL

    EPA Science Inventory

    This lecture will cover recent success in controlling and assessing the treatment of shallow ground water plumes of chlorinated solvents, other halogenated organic compounds, and methyl tert-butyl ether (MTBE).