Science.gov

Sample records for alkali cation concentration

  1. High capacity nickel battery material doped with alkali metal cations

    DOEpatents

    Jackovitz, John F.; Pantier, Earl A.

    1982-05-18

    A high capacity battery material is made, consisting essentially of hydrated Ni(II) hydroxide, and about 5 wt. % to about 40 wt. % of Ni(IV) hydrated oxide interlayer doped with alkali metal cations selected from potassium, sodium and lithium cations.

  2. High and rapid alkali cation storage in ultramicroporous carbonaceous materials

    NASA Astrophysics Data System (ADS)

    Yun, Young Soo; Lee, Seulbee; Kim, Na Rae; Kang, Minjee; Leal, Cecilia; Park, Kyu-Young; Kang, Kisuk; Jin, Hyoung-Joon

    2016-05-01

    To achieve better supercapacitor performance, efforts have focused on increasing the specific surface area of electrode materials to obtain higher energy and power density. The control of pores in these materials is one of the most effective ways to increase the surface area. However, when the size of pores decreases to a sub-nanometer regime, it becomes difficult to apply the conventional parallel-plate capacitor model because the charge separation distance (d-value) of the electrical double layer has a similar length scale. In this study, ultramicroporous carbonaceous materials (UCMs) containing sub-nanometer-scale pores are fabricated using a simple in situ carbonization/activation of cellulose-based compounds containing potassium. The results show that alkali cations act as charge carriers in the ultramicropores (<0.7 nm), and these materials can deliver high capacitances of ∼300 F g-1 at 0.5 A g-1 and 130 F g-1, even at a high current rate of 65 A g-1 in an aqueous medium. In addition, the UCM-based symmetric supercapacitors are stable over 10,000 cycles and have a high energy and power densities of 8.4 Wh kg-1 and 15,000 W kg-1, respectively. This study provides a better understanding of the effects of ultramicropores in alkali cation storage.

  3. Control of the alkali cation alignment in Prussian blue framework.

    PubMed

    Matsuda, Tomoyuki; Kim, Jungeun; Moritomo, Yutaka

    2012-07-01

    We found that the alignments of the alkali cations can be controlled by a distortion of Prussian blue framework; the rubidium ions form a rod structure in a distorted framework of Rb(0.85)Cu[Fe(CN)(6)](0.95)·1.3H(2)O, while the cesium ions are isolated dot structures in a non-distorted framework of Cs(0.97)Cu[Fe(CN)(6)](0.99)·1.1H(2)O. The Madelung energy calculations revealed that the novel rod structure is stabilized by the alternating rotations of the [Fe(CN)(6)] units within the three-dimensional coordination polymer framework. PMID:22466815

  4. Capillary electrophoresis of alkali and alkaline-earth cations with imidazole or benzylamine buffers

    SciTech Connect

    Morin, P.; Francois, C.; Dreux, M. . Lab. de Chimie Bioorganique et Analytique)

    1994-01-01

    The separation of alkali, alkaline earth, and ammonium cations in several samples of water was achieved by capillary electrophoresis with indirect UV detection. A solution of imidazole (10[sup [minus]2] M, pH 4.5) was used as a buffer to resolve a mixture of six cations (K[sup +], Na[sup +], Ca[sup 2+], Ba[sup 2+], Li[sup +] and Mg[sup 2+]) by capillary electrophoresis at 214 nm in less than 10 min. The addition of potassium cation to the running buffer has an influence on the resolution of Ca[sup 2+]/Na[sup +] and Na[sup +]/Mg[sup 2+] peaks. A linear relationship between the corrected peak area and concentration was obtained in the 1--10 ppm range for these cations using a hydrodynamic injector. This electrophoretic system permitted the separation of these inorganic cations at a 50 ppb-level concentration with a hydrodynamic injection, thus making it possible to quantitatively determine their presence in mineral waters by capillary electrophoresis. At pH 4.5, potassium and ammonium unfortunately have identical ionic mobilities causing them to comigrate in an imidazole buffer. Using an alkaline solution of benzylamine as carrier electrolyte, their separation can be successfully achieved with excellent resolution at 204 nm. The analyses of tap water and several mineral waters have been achieved by capillary electrophoresis.

  5. Alkali Metal Cation versus Proton and Methyl Cation Affinities: Structure and Bonding Mechanism

    PubMed Central

    Boughlala, Zakaria; Fonseca Guerra, Célia

    2016-01-01

    Abstract We have analyzed the structure and bonding of gas‐phase Cl−X and [HCl−X]+ complexes for X+= H+, CH3 +, Li+, and Na+, using relativistic density functional theory (DFT). We wish to establish a quantitative trend in affinities of the anionic and neutral Lewis bases Cl− and HCl for the various cations. The Cl−X bond becomes longer and weaker along X+ = H+, CH3 +, Li+, and Na+. Our main purpose is to understand the heterolytic bonding mechanism behind the intrinsic (i.e., in the absence of solvent) alkali metal cation affinities (AMCA) and how this compares with and differs from those of the proton affinity (PA) and methyl cation affinity (MCA). Our analyses are based on Kohn–Sham molecular orbital (KS‐MO) theory in combination with a quantitative energy decomposition analysis (EDA) that pinpoints the importance of the different features in the bonding mechanism. Orbital overlap appears to play an important role in determining the trend in cation affinities. PMID:27551660

  6. Alkali Metal Cation versus Proton and Methyl Cation Affinities: Structure and Bonding Mechanism.

    PubMed

    Boughlala, Zakaria; Fonseca Guerra, Célia; Bickelhaupt, F Matthias

    2016-06-01

    We have analyzed the structure and bonding of gas-phase Cl-X and [HCl-X](+) complexes for X(+)= H(+), CH3 (+), Li(+), and Na(+), using relativistic density functional theory (DFT). We wish to establish a quantitative trend in affinities of the anionic and neutral Lewis bases Cl(-) and HCl for the various cations. The Cl-X bond becomes longer and weaker along X(+) = H(+), CH3 (+), Li(+), and Na(+). Our main purpose is to understand the heterolytic bonding mechanism behind the intrinsic (i.e., in the absence of solvent) alkali metal cation affinities (AMCA) and how this compares with and differs from those of the proton affinity (PA) and methyl cation affinity (MCA). Our analyses are based on Kohn-Sham molecular orbital (KS-MO) theory in combination with a quantitative energy decomposition analysis (EDA) that pinpoints the importance of the different features in the bonding mechanism. Orbital overlap appears to play an important role in determining the trend in cation affinities. PMID:27551660

  7. Coordination Chemistry of Alkali and Alkaline-Earth Cations with Macrocyclic Ligands.

    ERIC Educational Resources Information Center

    Dietrich, Bernard

    1985-01-01

    Discusses: (l) alkali and alkaline-earth cations in biology (considering naturally occurring lonophores, their X-ray structures, and physiochemical studies); (2) synthetic complexing agents for groups IA and IIA; and (3) ion transport across membranes (examining neutral macrobicyclic ligands as metal cation carriers, transport by anionic carriers,…

  8. Ion specific effects of alkali cations on the catalytic activity of HIV-1 protease.

    PubMed

    Pokorná, Jana; Heyda, Jan; Konvalinka, Jan

    2013-01-01

    Human immunodeficiency virus 1 protease (HIV-1 PR), an important therapeutic target for the treatment of AIDS, is one of the most well-studied enzymes. However, there is still much to learn about the regulation of the activity and inhibition of this key viral enzyme. Specifically, the mechanism of activation of HIV-1 PR from the viral polyprotein upon HIV maturation is still not understood. It has been suggested that external factors like pH or salt concentration might contribute to regulation of this crucial step in the viral life cycle. Recently, we analyzed the activity of HIV-1 PR in aqueous solutions of sodium and potassium chloride by experimental determination of enzyme kinetics and molecular dynamics simulations. We showed that the effect of salt concentration is cation-specific [Heyda et al., Phys. Chem. Chem. Phys., 2009 (11), 7599]. In this study, we extended this analysis for other alkali cations and found that the dependence of the initial velocity of peptide substrate hydrolysis on the nature of the cation follows the Hofmeister series, with the exception of caesium. Significantly higher catalytic efficiencies both in terms of substrate binding (K(M)) and turnover number (kcat) are observed in the presence of K+ compared to Na+ or Li+ at corresponding salt concentrations. Molecular dynamics simulations suggest that both lithium and sodium are attracted more strongly than potassium and caesium to the protein surface, mostly due to stronger interactions with carboxylate side chain groups of aspartates and glutamates. Furthermore, we observed a surprising decrease in the K(M) value for a specific substrate at very low salt concentration. The molecular mechanism of this phenomenon will be further analyzed. PMID:23795510

  9. Solvation structure and transport properties of alkali cations in dimethyl sulfoxide under exogenous static electric fields

    SciTech Connect

    Kerisit, Sebastien; Vijayakumar, M. E-mail: karl.mueller@pnnl.gov; Han, Kee Sung; Mueller, Karl T. E-mail: karl.mueller@pnnl.gov

    2015-06-14

    A combination of molecular dynamics simulations and pulsed field gradient nuclear magnetic resonance spectroscopy is used to investigate the role of exogenous electric fields on the solvation structure and dynamics of alkali ions in dimethyl sulfoxide (DMSO) and as a function of temperature. Good agreement was obtained, for select alkali ions in the absence of an electric field, between calculated and experimentally determined diffusion coefficients normalized to that of pure DMSO. Our results indicate that temperatures of up to 400 K and external electric fields of up to 1 V nm{sup −1} have minimal effects on the solvation structure of the smaller alkali cations (Li{sup +} and Na{sup +}) due to their relatively strong ion-solvent interactions, whereas the solvation structures of the larger alkali cations (K{sup +}, Rb{sup +}, and Cs{sup +}) are significantly affected. In addition, although the DMSO exchange dynamics in the first solvation shell differ markedly for the two groups, the drift velocities and mobilities are not significantly affected by the nature of the alkali ion. Overall, although exogenous electric fields induce a drift displacement, their presence does not significantly affect the random diffusive displacement of the alkali ions in DMSO. System temperature is found to have generally a stronger influence on dynamical properties, such as the DMSO exchange dynamics and the ion mobilities, than the presence of electric fields.

  10. Enhancing electrocatalytic hydrogen evolution by nickel salicylaldimine complexes with alkali metal cations in aqueous media.

    PubMed

    Shao, Haiyan; Muduli, Subas K; Tran, Phong D; Soo, Han Sen

    2016-02-18

    New salicylaldimine nickel complexes, comprising only earth-abundant elements, have been developed for electrocatalytic hydrogen evolution in aqueous media. The second-sphere ether functionalities on the periphery of the complexes enhance the electrocatalytic activity in the presence of alkali metal cations. The electrocatalysts demonstrate improved performances especially in the economical and sustainable seawater reaction medium. PMID:26779580

  11. Theoretical study of alpha/beta-alanine and their protonated/alkali metal cationized complexes.

    PubMed

    Abirami, S; Xing, Y M; Tsang, C W; Ma, N L

    2005-01-27

    Density functional theory has been employed to model the structure and the relative stabilities of alpha/beta-alanine conformers and their protonated and alkali metal cationized complexes. In general, we find that the behavior of the beta-alanine (beta-Ala) system is quite similar to that of alpha-alanine (alpha-Ala). However, the presence of the methylene group (-CH2-) at the beta position in beta-Ala leads to a few key differences. First, the intramolecular hydrogen bonding patterns are different between free alpha- and beta-Ala. Second, the stability of zwitterionic species (in either the free ligand or alkali metal cationized complexes) is often enhanced in beta-Ala. Third, the preferred mode of alkali metal cation (M+) binding may also differ in alpha- and beta-Ala. Natural energy decomposition analysis has been applied here to gain further insight into the effects of the ligand, cation size, and mode of binding on the nature of interaction in these M+-Ala complexes. PMID:16833371

  12. Separation of alkali, alkaline earth and rare earth cations by liquid membranes containing macrocyclic carriers. Third progress report, September 1, 1980-April 1, 1981

    SciTech Connect

    Christensen, J.J.

    1981-04-15

    The overall objective of this project is to study the use of liquid membrane systems employing macrocyclic ligand carriers in making separations among metal cations. During the third year of the project, work continued in the development of a mathematical model to describe cation transport. The model was originally developed to describe the relationship between cation transport rate (J/sub M/) and the cation-macrocycle stability constant (K). The model was tested by determining the rates of transport of alkali and alkaline earth cations through chloroform membranes containing carrier ligands where the stability constants for their reaction with cations in methanol were known. From the results, it is clear that the model correctly describes the dependence of J/sub M/ on log K. The model also correctly describes the effect of cation concentration and carrier concentration on cation transport rates, as detailed in the previous progress report. During the third year of the project, the transport model was expanded so as to apply to competitive transport of cations from mixtures of two cations in the source aqueous phase. Data were collected under these conditions and the ability of the model to predict the flux of each cation was tested. Representative data of this type are presented along with corresponding data which were obtained when each cation was transported by the same carrier from a source phase containing only that cation. Comparison of transport rates determined under the two experimental conditions indicates that the relationship between the two sets of data is complex. To date, a few of these data involving transport from binary cation mixtures have been tested against the transport model. It was found that the model correctly predicts the cation fluxes from cation mixtures. These preliminary results indicate that the transport model can successfully predict separation factors when cation mixtures are used.

  13. Ultrafine Na-4-mica: uptake of alkali and alkaline earth metal cations by ion exchange.

    PubMed

    Kodama, Tatsuya; Ueda, Masahito; Nakamuro, Yumiko; Shimizu, Ken-ichi; Komarneni, Sridhar

    2004-06-01

    The cation exchange properties of alkali and alkaline earth metal cations at room temperature were investigated on an ultrafine, highly charged Na-4-mica (with the ideal mica composition Na4Mg6Al4Si4O20F4.xH2O). Ultrafine mica crystallites of 200 nm in size led to faster Sr2+ uptake kinetics in comparison to larger mica crystallites. The alkali metal ion (K+, Cs+, and Li+) exchange uptake was rapid, and complete exchange occurred within 30 min. For the alkaline earth metal ions Ba2+, Ca2+, and Mg2+, however, the exchange uptake required lengthy periods from 3 days to 4 weeks to be completed, similar to its Sr uptake, as previously reported. Kinetic models of the modified Freundlich and parabolic diffusion were examined for the experimental data on the Ba2+, Ca2+, and Mg2+ uptakes. The modified Freundlich model described well the Ba2+ ion uptake kinetics as well as that for the Sr2+ ion, while for the Ca2+ and Mg2+ ions the parabolic diffusion model showed better fitting. The alkali and alkaline earth ion exchange isotherms were also determined in comparison to the Sr2+ exchange isotherm. The thermodynamic equilibria for these cations were compared by using Kielland plots evaluated from the isotherms. PMID:15984251

  14. Local reactivity descriptors to predict the strength of Lewis acid sites in alkali cation-exchanged zeolites

    NASA Astrophysics Data System (ADS)

    Deka, Ramesh Ch.; Kinkar Roy, Ram; Hirao, Kimihiko

    2004-05-01

    Lewis acidity of alkali cation-exchanged zeolite is studied using local reactivity descriptors based on hard-soft acid-base (HSAB) concept. The local softness for nucleophilic attack ( sx+), local softness for electrophilic attack ( sx-) and their ratio, which is called `relative electrophilicity' ( sx+/ sx-), are calculated for the exchanged cations and Lewis acidity of the cations is found to decrease in the order: Li + > Na + > K + > Rb + > Cs +. Calculated blue shift of CO vibrational frequency (Δ ν) and interaction energy of CO molecule with alkali cation-exchanged zeolite clusters vary linearly with sx+/ sx- values.

  15. Chemistry of alkali cation exchanged faujasite and mesoporous NaX using alkyl halides and phosphates

    NASA Astrophysics Data System (ADS)

    Lee, Min-Hong

    The purpose of this work was to increase the reactivity of Faujasite X (NaX) zeolite toward the reactive decontamination of materials subject to nucleophilic attack by means of zeolite cation optimization and by means of the synthesis of mesoporous Faujasite X. Primary alkyl halides and trialkyl phosphates have been the test materials on which the cation-optimized and mesoporous zeolites have been tested. In the alkali cation optimization work, reactions of methyl iodide and 1-chloropropane with alkali metal cation exchanged Faujasite zeolite X were investigated at room temperature. The reactivity of the framework and the product formation were shown to depend on zeolite framework counter-cation. A quantitative study of zeolite product formation has been carried out, primarily using solid-state NMR spectroscopy. Large alkali cations showed preference toward substitution chemistry. In contrast, alkyl halide exposed LiX and NaX zeolites underwent both substitution and elimination. Subsequently introduced water molecules led to hydrolysis of framework species that was sensitive to framework counter-cation. The mesoporous NaX zeolites work undertakes to test whether an improvement in surface chemical reactivity can be achieved by introducing mesopores into the already reactive nucleophilic microporous NaX zeolite. Incorporation of the polydiallyl dimethyl ammonium chloride (PDADMAC) template and the formation of mesopores in Faujasite X zeolite (NaX) were successful and well-characterized. The mesopores are proposed to have occurred from incorporation of the cationic PDADMAC polymer into the zeolite by compensating zeolite framework charge. Subsequent sodium cation exchange of calcined mesoporous NaX was shown to restore the chemical reactivity characteristic of as-synthesized NaX. Trialkyl organophosphorous compounds underwent substitution reactions. The reactivity of both microporous and mesoporous Faujasite zeolite X and the product formation was shown to depend on

  16. [Oat growth and cation absorption characteristics under salt and alkali stress].

    PubMed

    Fan, Yuan; Ren, Chang-Zhong; Li, Pin-Fang; Ren, Tu-Sheng

    2011-11-01

    This paper monitored the oat growth and cation absorption characteristics on a saline-alkali soil in the Baicheng region of Jilin Province under low, medium, and high levels of salt stress. No significant differences were observed in the shoot growth and yield components under the three levels of salt stress, but the root biomass and root/shoot ratio decreased significantly with increasing salt stress level. At maturing stage, the root/shoot ratio under medium and high salt stresses was 77.2% and 64.5% of that under low salt stress, respectively. Under the three levels of salt stress, the K+/Na+ and Ca2+/Na+ ratios in oat plant had significant differences at trefoil stage, but no significant differences at heading stage. With the increase of salt stress level, the cation absorption selectivity coefficient of oat at filling stage decreased significantly, but the transportation selectivity coefficient had no significant difference under the three levels of stress. It was concluded that oat could adapt to the salt and alkali stress of soda-alkaline soil to some extent, and the adaptation capability decreased with the increasing level of stress. The decrease of oat root biomass and the stronger ion selective absorption capacity at heading stage under salt and alkali stress could benefit the shoot growth and yield components of oat. PMID:22303664

  17. The role of alkali metal cations in the stabilization of guanine quadruplexes: why K(+) is the best.

    PubMed

    Zaccaria, F; Paragi, G; Fonseca Guerra, C

    2016-08-21

    The alkali metal ion affinity of guanine quadruplexes has been studied using dispersion-corrected density functional theory (DFT-D). We have done computational investigations in aqueous solution that mimics artificial supramolecular conditions where guanine bases assemble into stacked quartets as well as biological environments in which telomeric quadruplexes are formed. In both cases, an alkali metal cation is needed to assist self-assembly. Our quantum chemical computations on these supramolecular systems are able to reproduce the experimental order of affinity of the guanine quadruplexes for the cations Li(+), Na(+), K(+), Rb(+), and Cs(+). The strongest binding is computed between the potassium cation and the quadruplex as it occurs in nature. The desolvation and the size of alkali metal cations are thought to be responsible for the order of affinity. Until now, the relative importance of these two factors has remained unclear and debated. By assessing the quantum chemical 'size' of the cation, determining the amount of deformation of the quadruplex needed to accommodate the cation and through the energy decomposition analysis (EDA) of the interaction energy between the cation and the guanines, we reveal that the desolvation and size of the alkali metal cation are both almost equally responsible for the order of affinity. PMID:27185388

  18. Gas-phase synthesis of hydrodiphenylcyclopropenylium via nonclassical Favorskii rearrangement from alkali-cationized alpha,alpha'-dibromodibenzyl ketone.

    PubMed

    Zhao, Zhi-Xiong; Wang, Hao-Yang; Xu, Chu; Guo, Yin-Long

    2010-09-15

    The gas-phase synthesis of hydrodiphenylcyclopropenylium from alkali-cationized alpha,alpha'-dibromodibenzyl ketone (1) via nonclassical Lewis-acid-induced Favorskii rearrangement has been studied by electrospray ionization/tandem mass spectrometry (ESI-MS/MS) and theoretical methods, showing that cations [1-Br](+) by debromination from 1 and 1.M(+)(M = Li or Na) by alkali-metal cationization of 1 could convert into the protonated diphenylcyclopropenone 2.H(+) by collision-induced dissociation in the gas phase. A concerted mechanism for the Lewis-acid-induced Favorskii rearrangement from alkali-metal-cationized alpha,alpha'-dibromodibenzyl ketone was proposed and studied, based on mass spectrometric results and theoretical methods. PMID:20740544

  19. Molecular mechanics (MM3) calculations on benzocrown ether complexes of the alkali and alkaline earth cations

    SciTech Connect

    Yang, Linrong R.; Hay, B.P.

    1997-12-31

    The new metal-ligand feature of MM3 has been extended to benzocrown ether complexes of alkali and alkaline earth cations. Over 50 complexes were compared with the crystal structures retrieved from Cambridge Crystal Database. The results agree with experimental data. The averages of absolute deviations between experimental and calculated structural features are: metal-oxygen bond length, 0.03 {angstrom}; Metal-oxygen-carbon angles, 4.1{degrees}; and Metal-oxygen-carbon-carbon angles: 5.1{degrees}. Development of structure-function relationships is in progress.

  20. Photoionization of the alkali dimer cations Li+2, Na+2 and LiNa+

    NASA Astrophysics Data System (ADS)

    Dumitriu, Irina; Vanne, Yulian V.; Awasthi, Manohar; Saenz, Alejandro

    2007-05-01

    Photoionization cross sections for the three alkali dimer cations (Li+2, Na+2 and LiNa+) were calculated at the equilibrium internuclear distance for parallel, perpendicular and isotropic orientations of the molecular axis with respect to the field. A model-potential method was used for the description of the cores. The influence of the model-potential parameters on the photoionization spectra was investigated. Two different methods, a time-independent and a time-dependent one, were implemented and used for computing the cross sections.

  1. Emerging roles of alkali cation/proton exchangers in organellar homeostasis

    PubMed Central

    Orlowski, John; Grinstein, Sergio

    2016-01-01

    The regulated movement of monovalent cations such as H+, Li+, Na+ and K+ across biological membranes influences a myriad of cellular processes and is fundamental to all living organisms. This is accomplished by a multiplicity of ion channels, pumps and transporters. Our insight into their molecular, cellular and physiological diversity has increased greatly in the past few years with the advent of genome sequencing, genetic manipulation and sophisticated imaging techniques. One of the revelations from these studies is the emergence of novel alkali cation/protons exchangers that are present in endomembranes, where they function to regulate not only intraorganellar pH but also vesicular biogenesis, trafficking and other aspects of cellular homeostasis. PMID:17646094

  2. The syntheses of phenol-containing azamacrocycles and liquid membrane transports of alkali cations

    NASA Astrophysics Data System (ADS)

    Ma, Shu-Lan; Qi, Chuan-Min; Zhu, Wen-Xiang; Guo, Qian-Ling; Liu, Ying-Chun; Zhang, Jing

    2005-01-01

    Two new tetra- N-substituted tetraazacrown ether derivatives, 4,7,13,16-tetra(2-hydroxy-3,4-dimethylbenzyl)-1,10-dioxa-4,7,13,16-tetraazacyclooctadecane (1) and 4,7,13,16-tetra(5- t-butyl-2-hydroxybenzyl)-1,10-dioxa-4,7,13,16-tetraazacyclooctadecane (2), have been synthesized via one-pot Mannich reaction. The compound 2 was structurally characterized. The liquid membrane transports of alkali metal cations using these two new macrocycles and the other two bisphenol-containing diaza-18-crown-6 ligands as ion-carriers were also studied. The results show that the rates of cation transport are closely related to the number of nitrogen donors and the steric effect of the substituted groups. Compared with some macrocyclic ligands, the two newly synthesized tetraazamacrocycles showed a good selectivity for Li +, and the two diazamacrocycles showed a good selectivity for Na +.

  3. Maternal exposure to alkali, alkali earth, transition and other metals: Concentrations and predictors of exposure.

    PubMed

    Hinwood, A L; Stasinska, A; Callan, A C; Heyworth, J; Ramalingam, M; Boyce, M; McCafferty, P; Odland, J Ø

    2015-09-01

    Most studies of metals exposure focus on the heavy metals. There are many other metals (the transition, alkali and alkaline earth metals in particular) in common use in electronics, defense industries, emitted via combustion and which are naturally present in the environment, that have received limited attention in terms of human exposure. We analysed samples of whole blood (172), urine (173) and drinking water (172) for antimony, beryllium, bismuth, cesium, gallium, rubidium, silver, strontium, thallium, thorium and vanadium using ICPMS. In general most metals concentrations were low and below the analytical limit of detection with some high concentrations observed. Few factors examined in regression models were shown to influence biological metals concentrations and explained little of the variation. Further study is required to establish the source of metals exposures at the high end of the ranges of concentrations measured and the potential for any adverse health impacts in children. PMID:25984984

  4. Study of Ion Specific Interactions of Alkali Cations with Dicarboxylate Dianions

    SciTech Connect

    Murdachaew, Garold; Valiev, Marat; Kathmann, Shawn M.; Wang, Xue B.

    2012-02-10

    Alkali metal cations often show pronounced ion specific interactions and selectivity with macromolecules in biological processes, colloids, and interfacial sciences, but a fundamental understanding about the underlying microscopic mechanism is still very limited. Here we report a direct probe of interactions between alkali metal cations (M{sup +}) and dicarboxylate dianions, O{sub 2}C(CH{sub 2})nCO{sub 2} (D{sub n}{sup 2-}) in the gas phase by combined photoelectron spectroscopy (PES) and ab initio electronic structure calculation on nine M{sup +}-D{sub n}{sup 2-} complexes (M = Li, Na, K; n = 2, 4, 6). PES spectra show that the electron binding energy (EBE) decreases from Li{sup +} to Na{sup +} to K{sup +} for complexes of M{sup +}-D{sub 2}{sup 2-}, whereas the order is Li{sup +} cation M{sup +}. The observed variance of EBEs reflects how well a specific dicarboxylate dianion accommodates each M{sup +}. This work demonstrates the delicate interplay among several factors (electrostatic interaction, size matching, and strain energy) that likely play critical roles in determining the structures and energetics of gaseous clusters as well as ion specificity and selectivity in solutions and biological systems.

  5. Ca(2+) function in photosynthetic oxygen evolution studied by alkali metal cations substitution.

    PubMed

    Ono, T; Rompel, A; Mino, H; Chiba, N

    2001-10-01

    Effects of adding monovalent alkali metal cations to Ca(2+)-depleted photosystem (PS)II membranes on the biochemical and spectroscopic properties of the oxygen-evolving complex were studied. The Ca(2+)-dependent oxygen evolution was competitively inhibited by K(+), Rb(+), and Cs(+), the ionic radii of which are larger than the radius of Ca(2+) but not inhibited significantly by Li(+) and Na(+), the ionic radii of which are smaller than that of Ca(2+). Ca(2+)-depleted membranes without metal cation supplementation showed normal S(2) multiline electron paramagnetic resonance (EPR) signal and an S(2)Q(A)(-) thermoluminescence (TL) band with a normal peak temperature after illumination under conditions for single turnover of PSII. Membranes supplemented with Li(+) or Na(+) showed properties similar to those of the Ca(2+)-depleted membranes, except for a small difference in the TL peak temperatures. The peak temperature of the TL band of membranes supplemented with K(+), Rb(+), or Cs(+) was elevated to approximately 38 degrees C which coincided with that of Y(D)(+)Q(A)(-) TL band, and no S(2) EPR signals were detected. The K(+)-induced high-temperature TL band and the S(2)Q(A)(-) TL band were interconvertible by the addition of K(+) or Ca(2+) in the dark. Both the Ca(2+)-depleted and the K(+)-substituted membranes showed the narrow EPR signal corresponding to the S(2)Y(Z)(+) state at g = 2 by illuminating the membranes under multiple turnover conditions. These results indicate that the ionic radii of the cations occupying Ca(2+)-binding site crucially affect the properties of the manganese cluster. PMID:11566758

  6. An extended basis set {ital ab} {ital initio} study of alkali metal cation--water clusters

    SciTech Connect

    Feller, D.; Glendening, E.D.; Woon, D.E.; Feyereisen, M.W.

    1995-09-01

    Ionic clusters comprised of a single alkali metal cation and up to eight water molecules were studied at the Hartree--Fock and correlated levels of theory using the correlation consistent sequence of basis sets. Estimates of the degree of convergence in the computed properties with respect to the complete basis set limit were facilitated by the underlying systematic manner in which the correlation consistent sets approach completeness. In favorable cases, improved property values could be obtained by fitting finite basis set results with a simple analytical expression in order to extrapolate to the complete basis set limit. The sensitivity of structures and binding energies were analyzed with regard to the inclusion of valence and core-valence correlation recovery at the MP2, MP4, and CCSD(T) levels of theory. The replacement of metal core electrons and the introduction of relativistic contributions via effective core potentials was compared to corresponding all-electron results. {copyright} {ital 1995} {ital American} {ital Institute} {ital of} {ital Physics}.

  7. Selective trans-membrane transport of alkali and alkaline earth cations through graphene oxide membranes based on cation-π interactions.

    PubMed

    Sun, Pengzhan; Zheng, Feng; Zhu, Miao; Song, Zhigong; Wang, Kunlin; Zhong, Minlin; Wu, Dehai; Little, Reginald B; Xu, Zhiping; Zhu, Hongwei

    2014-01-28

    Graphene and graphene oxide (G-O) have been demonstrated to be excellent filters for various gases and liquids, showing potential applications in areas such as molecular sieving and water desalination. In this paper, the selective trans-membrane transport properties of alkali and alkaline earth cations through a membrane composed of stacked and overlapped G-O sheets ("G-O membrane") are investigated. The thermodynamics of the ion transport process reveal that the competition between the generated thermal motions and the interactions of cations with the G-O sheets results in the different penetration behaviors to temperature variations for the considered cations (K(+), Mg(2+), Ca(2+), and Ba(2+)). The interactions between the studied metal atoms and graphene are quantified by first-principles calculations based on the plane-wave-basis-set density functional theory (DFT) approach. The mechanism of the selective ion trans-membrane transportation is discussed further and found to be consistent with the concept of cation-π interactions involved in biological systems. The balance between cation-π interactions of the cations considered with the sp(2) clusters of G-O membranes and the desolvation effect of the ions is responsible for the selectivity of G-O membranes toward the penetration of different ions. These results help us better understand the ion transport process through G-O membranes, from which the possibility of modeling the ion transport behavior of cellular membrane using G-O can be discussed further. The selectivity toward different ions also makes G-O membrane a promising candidate in areas of membrane separations. PMID:24401025

  8. Preparation of decarboxylic-functionalized weak cation exchanger and application for simultaneous separation of alkali, alkaline earth and transition metals.

    PubMed

    Peng, Yahui; Gan, Yihui; He, Chengxia; Yang, Bingcheng; Guo, Zhimou; Liang, Xinmiao

    2016-06-01

    A novel weak cation exchanger (WCX) with dicarboxyl groups functionalized has been developed by clicking mercaptosuccinic acid onto silica gel. The simple synthesis starts with modification of silica gel with triethoxyvinylsilane, followed by efficient coupling vinyl-bonded silica with mercaptosuccinic acid via a "thiol-ene" click reaction. The obtained WCX demonstrated good separation and high selectivity towards common metals. Simultaneous separation of 10 alkali, alkaline earth and transition metals was achieved within 12min. Ion exchange and complex mechanism dominates the separation process. Its utility was demonstrated for determination of metals in tap water. PMID:27130093

  9. Ion-exchange selectivities of periderm and cuticular membranes toward alkali cations

    SciTech Connect

    Ersoz, M.; Duncan, H.J.

    1994-08-01

    The ion-exchange selectivities of lithium, sodium, potassium, and cesium on isolated potato periderm (Solanum tuberosum) and pear fruit cuticular membranes were investigated; the general order of preference both for cation selectivities and ion-exchange capacities was lithium > sodium > potassium > cesium. The potato periderm and pear fruit cuticular membranes exhibited a behavior typical of ion-exchange resins of the weak acid type. At constant pH 7, the ion-exchange capacities of periderm and cuticular membranes increased with hydrated ionic radius, and also with increasing pH and neutral salt concentration, and decreased with crystal ionic radius. Counterion selectivities also exhibited the same behavior. The ion-exchange properties are discussed in terms of the structure and function of potato periderm and pear fruit cuticular membranes.

  10. Structural Role of Alkali Cations in Calcium Aluminosilicate Glasses as Examined Using Oxygen-17 Solid-State Nuclear Magnetic Resonance Spectroscopy

    NASA Astrophysics Data System (ADS)

    Sukenaga, Sohei; Kanehashi, Koji; Shibata, Hiroyuki; Saito, Noritaka; Nakashima, Kunihiko

    2016-05-01

    The structural roles of alkali and calcium cations are important for understanding the physical and chemical properties of aluminosilicate melts and glasses. Recently, oxygen-17 nuclear magnetic resonance (17O NMR) studies of calcium-sodium aluminosilicate glasses showed that these structural roles are not randomly given, but rather each cation has its own preferential role. However, the relationship between cation type and role preference in calcium aluminosilicate glass is not completely understood. In the present study, the structural roles of lithium, sodium, and potassium cations in selected calcium aluminosilicate glasses are investigated using 17O solid-state NMR experiments. Data from these experiments clearly show that potassium cations have a notably stronger tendency to act as charge compensators within the network structure, compared to sodium and lithium cations. The result of 17O NMR experiment also showed that sodium and lithium cations in part act as network modifier alongside with calcium cations.

  11. Structural Role of Alkali Cations in Calcium Aluminosilicate Glasses as Examined Using Oxygen-17 Solid-State Nuclear Magnetic Resonance Spectroscopy

    NASA Astrophysics Data System (ADS)

    Sukenaga, Sohei; Kanehashi, Koji; Shibata, Hiroyuki; Saito, Noritaka; Nakashima, Kunihiko

    2016-08-01

    The structural roles of alkali and calcium cations are important for understanding the physical and chemical properties of aluminosilicate melts and glasses. Recently, oxygen-17 nuclear magnetic resonance (17O NMR) studies of calcium-sodium aluminosilicate glasses showed that these structural roles are not randomly given, but rather each cation has its own preferential role. However, the relationship between cation type and role preference in calcium aluminosilicate glass is not completely understood. In the present study, the structural roles of lithium, sodium, and potassium cations in selected calcium aluminosilicate glasses are investigated using 17O solid-state NMR experiments. Data from these experiments clearly show that potassium cations have a notably stronger tendency to act as charge compensators within the network structure, compared to sodium and lithium cations. The result of 17O NMR experiment also showed that sodium and lithium cations in part act as network modifier alongside with calcium cations.

  12. Competition between pi and non-pi cation-binding sites in aromatic amino acids: a theoretical study of alkali metal cation (Li+, Na+, K+)-phenylalanine complexes.

    PubMed

    Siu, Fung Ming; Ma, Ngai Ling; Tsang, Chun Wai

    2004-04-19

    To understand the cation-pi interaction in aromatic amino acids and peptides, the binding of M(+) (where M(+) = Li(+), Na(+), and K(+)) to phenylalanine (Phe) is studied at the best level of density functional theory reported so far. The different modes of M(+) binding show the same order of binding affinity (Li(+)>Na(+)>K(+)), in the approximate ratio of 2.2:1.5:1.0. The most stable binding mode is one in which the M(+) is stabilized by a tridentate interaction between the cation and the carbonyl oxygen (O[double bond]C), amino nitrogen (--NH(2)), and aromatic pi ring; the absolute Li(+), Na(+), and K(+) affinities are estimated theoretically to be 275, 201, and 141 kJ mol(-1), respectively. Factors affecting the relative stabilities of various M(+)-Phe binding modes and conformers have been identified, with ion-dipole interaction playing an important role. We found that the trend of pi and non-pi cation bonding distances (Na(+)-pi>Na(+)-N>Na(+)-O and K(+)-pi>K(+)-N>K(+)-O) in our theoretical Na(+)/K(+)-Phe structures are in agreement with the reported X-ray crystal structures of model synthetic receptors (sodium and potassium bound lariat ether complexes), even though the average alkali metal cation-pi distance found in the crystal structures is longer. This difference between the solid and the gas-phase structures can be reconciled by taking the higher coordination number of the cations in the lariat ether complexes into account. PMID:15079836

  13. Influence of alkali metal cations on the thermal, mechanical and morphological properties of rectorite/chitosan bio-nanocomposite films.

    PubMed

    Babul Reddy, A; Jayaramudu, J; Siva Mohan Reddy, G; Manjula, B; Sadiku, E R

    2015-05-20

    The main theme of this work is to study the influence of ion-exchangeable alkali metal cations, such as: Li(+), Na(+), K(+), and Cs(+) on the thermal, mechanical and morphological properties. In this regard, a set of rectorite/chitosan (REC-CS) bio-nanocomposite films (BNCFs) was prepared by facile reaction of chitosan with ion-exchanged REC clay. The microstructure and morphology of BNCFs were investigated with XRD, TEM, SEM and AFM. Thermal and tensile properties of BNCFs were also investigated. As revealed from TEM and XRD results, the BNCFs featured a mixed morphology. Some intercalated clay sheets, together with nano-sized clay tactoids were obtained in LiREC/CS, NaREC/CS and KREC/CS of the BNCFs. From fractured surface study, via SEM, it was observed that the dispersion of chitosan polymer attaches to (and covers) the clay platelets. FTIR confirmed strong hydrogen bonds between clay and chitosan polymer. In addition, the thermal stabilities significantly varied when alkali metal cations varied from Li(+) to Cs(+). The BNCFs featured high tensile strengths (up to 84 MPa) and tensile moduli (up to 45 GPa). After evaluating these properties of BNCFs, we came to conclusion that these bio-nano composites can be used for packaging applications. PMID:25817663

  14. Alkali metal cation complexation by 1,3-alternate, mono-ionisable calix[4]arene-benzocrown-6 compounds

    DOE PAGESBeta

    Surowiec, Malgorzata A.; Custelcean, Radu; Surowiec, Kazimierz; Bartsch, Richard A.

    2014-04-23

    Alkali metal cation extraction behavior for two series of 1,3-alternate, mono-ionizable calix[4]arene-benzocrown-6 compounds is examined. In Series 1, the proton-ionizable group is a substituent on the benzo group of the polyether ring that directs it away from the crown ether cavity. In Series 2, the proton-ionizable group is attached to one para position in the calixarene framework, thus positioning it over the crown ether ring. Competitive solvent extraction of alkali metal cations from aqueous solutions into chloroform shows high Cs+ efficiency and selectivity. Single-species extraction pH profiles of Cs+ for Series 1 and 2 ligands with the same proton-ionizable groupmore » are very similar. Thus, association of Cs+ with the calixcrown ring is more important than the the proton-ionizable group’s position in relation to the crown ether cavity. Solid-state structures are presented for two unionized ligands from Series 2, as is a crystal containing two different ionized ligand–Cs+ complexes.« less

  15. Alkali metal cation complexation by 1,3-alternate, mono-ionisable calix[4]arene-benzocrown-6 compounds

    SciTech Connect

    Surowiec, Malgorzata A.; Custelcean, Radu; Surowiec, Kazimierz; Bartsch, Richard A.

    2014-04-23

    Alkali metal cation extraction behavior for two series of 1,3-alternate, mono-ionizable calix[4]arene-benzocrown-6 compounds is examined. In Series 1, the proton-ionizable group is a substituent on the benzo group of the polyether ring that directs it away from the crown ether cavity. In Series 2, the proton-ionizable group is attached to one para position in the calixarene framework, thus positioning it over the crown ether ring. Competitive solvent extraction of alkali metal cations from aqueous solutions into chloroform shows high Cs+ efficiency and selectivity. Single-species extraction pH profiles of Cs+ for Series 1 and 2 ligands with the same proton-ionizable group are very similar. Thus, association of Cs+ with the calixcrown ring is more important than the the proton-ionizable group’s position in relation to the crown ether cavity. Solid-state structures are presented for two unionized ligands from Series 2, as is a crystal containing two different ionized ligand–Cs+ complexes.

  16. Electroosmosis through α-Hemolysin That Depends on Alkali Cation Type.

    PubMed

    Piguet, Fabien; Discala, Francoise; Breton, Marie-France; Pelta, Juan; Bacri, Laurent; Oukhaled, Abdelghani

    2014-12-18

    We demonstrate experimentally the existence of an electroosmotic flow (EOF) through the wild-type nanopore of α-hemolysin in a large range of applied voltages and salt concentrations for two different salts, LiCl and KCl. EOF controls the entry frequency and residence time of small neutral molecules (β-cyclodextrins, βCD) in the nanopore. The strength of EOF depends on the applied voltage, on the salt concentration, and, interestingly, on the nature of the cations in solution. In particular, EOF is stronger in the presence of LiCl than KCl. We interpret our results with a simple theoretical model that takes into account the pore selectivity and the solvation of ions. A stronger EOF in the presence of LiCl is found to originate essentially in a stronger anionic selectivity of the pore. Our work provides a new and easy way to control EOF in protein nanopores, without resorting to chemical modifications of the pore. PMID:26273988

  17. Structure and photoabsorption properties of cationic alkali dimers solvated in neon clusters.

    PubMed

    Zanuttini, D; Douady, J; Jacquet, E; Giglio, E; Gervais, B

    2010-11-01

    We present a theoretical investigation of the structure and optical absorption of M(2)(+) alkali dimers (M=Li,Na,K) solvated in Ne(n) clusters for n=1 to a few tens Ne atoms. For all these alkali, the lowest-energy isomers are obtained by aggregation of the first Ne atoms at the extremity of the alkali molecule. This particular geometry, common to other M(2)(+)-rare gas clusters, is intimately related to the shape of the electronic density of the X  (2)Σ(g)(+) ground state of the bare M(2)(+) molecules. The structure of the first solvation shell presents equilateral Ne(3) and capped pentagonal Ne(6) motifs, which are characteristic of pure rare gas clusters. The size and geometry of the complete solvation shell depend on the alkali and were obtained at n=22 with a D(4h) symmetry for Li and at n=27 with a D(5h) symmetry for Na. For K, our study suggests that the closure of the first solvation shell occurs well beyond n=36. We show that the atomic arrangement of these clusters has a profound influence on their optical absorption spectrum. In particular, the XΣ transition from the X  (2)Σ(g)(+) ground state to the first excited (2)Σ(u)(+) state is strongly blueshifted in the Frank-Condon area. PMID:21054047

  18. Thermal history effects on electrical relaxation and conductivity for potassium silicate glass with low alkali concentrations

    NASA Technical Reports Server (NTRS)

    Angel, Paul W.; Hann, Raiford E.; Cooper, Alfred R.

    1993-01-01

    Electrical response measurements from 10 Hz to 100 kHz between 120 and 540 C were made on potassium-silicate glasses with alkali oxide contents of 2, 3, 5 and 10 mol percent. Low alkali content glasses were chosen in order to try to reduce the Coulombic interactions between alkali ions to the point that frozen structural effects from the glass could be observed. Conductivity and electrical relaxation responses for both annealed and quenched glasses of the same composition were compared. Lower DC conductivity (sigma(sub DC)) activation energies were measured for the quenched compared to the annealed glasses. The two glasses with the lowest alkali contents exhibited a non-Arrhenius concave up curvature in the log(sigma(sub DC)) against 1/T plots, which decreased upon quenching. A sharp decrease in sigma(sub DC) was observed for glasses containing K2O concentrations of 5 mol percent or less. The log modulus loss peak (M'') maximum frequency plots against 1/T all showed Arrhenius behavior for both annealed and quenched samples. The activation energies for these plots closely agreed with the sigma(sub DC) activation energies. A sharp increase in activation energy was observed for both series as the potassium oxide concentration decreased. Changes in the electrical response are attributed to structural effects due to different alkali concentrations. Differences between the annealed and quenched response are linked to a change in the distribution of activation energies (DAE).

  19. The Debaryomyces hansenii NHA1 gene encodes a plasma membrane alkali-metal-cation antiporter with broad substrate specificity.

    PubMed

    Velkova, Klara; Sychrova, Hana

    2006-03-15

    Debaryomyces hansenii is a yeast species often found in salty environments. Its genome sequence is known completely, but the mechanisms behind its halotolerance are poorly understood. In the D. hansenii genome, there is a gene strongly homologous to the Saccharomyces cerevisiae NHA1 gene (encoding a plasma membrane Na+/H+ antiporter). We isolated this DhNHA1 gene from two D. hansenii strains (CBS 767 and CBS 1793) differing in their osmotolerance. Both DhNHA1 alleles were heterologously expressed in a S. cerevisiae strain lacking its own systems for the efflux of alkali metal cations (BW31a, ena1-4delta nha1delta). D. hansenii Na+/H+ antiporters were localized in the plasma membrane of BW31a cells, their presence increased BW31a tolerance to sodium, potassium, lithium and also rubidium. Measurements of Na+ and K+ efflux from S. cerevisiae cells expressing DhNHA1 alleles show that the D. hansenii antiporters efficiently transported both cations out of cells. The sodium and potassium transport activity of Nha1 antiporters from both D. hansenii strains was almost identical, indicating that plasma membrane antiporter activity is not one of the factors determining the different levels of halotolerance in the two strains. PMID:16303259

  20. Selective removal of alkali metal cations from multiply-charged ions via gas-phase ion/ion reactions using weakly coordinating anions.

    PubMed

    Luongo, Carl A; Bu, Jiexun; Burke, Nicole L; Gilbert, Joshua D; Prentice, Boone M; Cummings, Steven; Reed, Christopher A; McLuckey, Scott A

    2015-03-01

    Selective removal of alkali metal cations from mixed cation multiply-charged peptide ions is demonstrated here using gas-phase ion/ion reactions with a series of weakly coordinating anions (WCAs), including hexafluorophosphate (PF6 (-)), tetrakis[3,5-bis(trifluoromethyl)phenyl]borate (BARF), tetrakis(pentafluorophenyl)borate (TPPB), and carborane (CHB11Cl11 (-)). In all cases, a long-lived complex is generated by dication/anion condensation followed by ion activation to compare proton transfer with alkali ion transfer from the peptide to the anion. The carborane anion was the only anion studied to undergo dissociation exclusively through loss of the metallated anion, regardless of the studied metal adduct. All other anions studied yield varying abundances of protonated and metallated peptide depending on the peptide sequence and the metal identity. Density functional theory calculations suggest that for the WCAs studied, metal ion transfer is most strongly favored thermodynamically, which is consistent with the experimental results. The carborane anion is demonstrated to be a robust reagent for the selective removal of alkali metal cations from peptide cations with mixtures of excess protons and metal cations. PMID:25560986

  1. Selective Removal of Alkali Metal Cations from Multiply-Charged Ions via Gas-Phase Ion/Ion Reactions Using Weakly Coordinating Anions

    NASA Astrophysics Data System (ADS)

    Luongo, Carl A.; Bu, Jiexun; Burke, Nicole L.; Gilbert, Joshua D.; Prentice, Boone M.; Cummings, Steven; Reed, Christopher A.; McLuckey, Scott A.

    2015-03-01

    Selective removal of alkali metal cations from mixed cation multiply-charged peptide ions is demonstrated here using gas-phase ion/ion reactions with a series of weakly coordinating anions (WCAs), including hexafluorophosphate (PF6 -), tetrakis[3,5-bis(trifluoromethyl)phenyl]borate (BARF), tetrakis(pentafluorophenyl)borate (TPPB), and carborane (CHB11Cl11 -). In all cases, a long-lived complex is generated by dication/anion condensation followed by ion activation to compare proton transfer with alkali ion transfer from the peptide to the anion. The carborane anion was the only anion studied to undergo dissociation exclusively through loss of the metallated anion, regardless of the studied metal adduct. All other anions studied yield varying abundances of protonated and metallated peptide depending on the peptide sequence and the metal identity. Density functional theory calculations suggest that for the WCAs studied, metal ion transfer is most strongly favored thermodynamically, which is consistent with the experimental results. The carborane anion is demonstrated to be a robust reagent for the selective removal of alkali metal cations from peptide cations with mixtures of excess protons and metal cations.

  2. Complexation of Donor-Acceptor Substituted Aza-Crowns with Alkali and Alkaline Earth Metal Cations. Charge Transfer and Recoordination in Excited State.

    PubMed

    Volchkov, Valery V; Gostev, Fedor E; Shelaev, Ivan V; Nadtochenko, Viktor A; Dmitrieva, Svetlana N; Gromov, Sergey P; Alfimov, Mikhail V; Melnikov, Mikhail Ya

    2016-03-01

    Complexation between two aza-15-crown-5 ethers bearing electron donor and acceptor fragments and alkali and alkaline earth perchlorates has been studied using absorption, steady-state fluorescence and femtosecond transient absorption spectroscopy. The spectral-luminescent parameters, the stability and dissociation constants of the complexes were calculated. The intramolecular charge transfer reaction takes place both in the excited state of the crowns and their complexes 1:1; the latter is subjected to photorecoordination resulting in a weakening or a complete disruption of coordination bond between nitrogen atom and metal cation, disposed within a cavity of the crown. The compounds investigated can be viewed as novel optical molecular sensors for alkali and alkaline-earth metal cations. The photoejection of a metal cation into the bulk was not observed. PMID:26670689

  3. Tetrazole-5-carboxylic acid based salts of earth alkali and transition metal cations.

    PubMed

    Hartdegen, Vera; Klapötke, Thomas M; Sproll, Stefan M

    2009-10-01

    The tetrazole-5-carboxylate anion was investigated as ligand for earth alkali metal and transition metal complexes. Therefore, the strontium 4a (*3 H(2)O, *2.75 H(2)O, *2.5 H(2)O), barium 4b (*3 H(2)O), copper 4c (*3.5 H(2)O, *4 H(2)O), manganese 4d (*4 H(2)O, *5 H(2)O), and silver tetrazol-5-carboxylate 4e (*1.56 H(2)O) were synthesized and characterized by vibrational spectroscopy (IR), and the crystal structures of 4a (*2.75 H(2)O, *2.5 H(2)O), 4b*3 H(2)O, 4c*4 H(2)O, and 4d*5 H(2)O were determined using single crystal X-ray diffraction. The thermal stability was investigated by DSC-measurements, and the sensitivity toward impact and friction was determined by BAM-standards. The copper, strontium, and barium tetrazole-5-carboxyate proved to be suitable thermal and physical stable colorants for pyrotechnic compositions. The crystal structure of the tetragonal modification of strontium tetrazole-5-carboxyate possesses channels along the c-axis, leading to a porous material. PMID:19780625

  4. Effects of cation concentration on photocatalytic performance over magnesium vanadates

    SciTech Connect

    Li, Peng; Zhou, Wei; Wang, Xin; Zhang, Yan; Wang, Defa; Umezawa, Naoto E-mail: ABE.Hideki@nims.go.jp; Abe, Hideki E-mail: ABE.Hideki@nims.go.jp; Ye, Jinhua

    2015-10-01

    A series of magnesium vanadates (MgV {sub 2}O{sub 6}, Mg{sub 2}V {sub 2}O{sub 7}, and Mg{sub 3}V {sub 2}O{sub 8}) were synthesized to investigate the effect of cation concentration on photocatalytic performance. The samples were characterized by X-ray diffraction, field emission-scanning electron microscopy, UV-visible diffuse reflectance spectroscopy, and fluorescence spectroscopy. The photocatalytic O{sub 2} evolution experiments under visible light irradiation showed Mg{sub 2}V {sub 2}O{sub 7} exhibits the best performance, while Mg{sub 3}V {sub 2}O{sub 8} has the lowest activity. The density functional theory calculations indicated that the lowest unoccupied states of Mg{sub 3}V {sub 2}O{sub 8} are the mostly localized by the cation layers. The fluorescence spectra and fluorescence decay curves gave evident performances of excited states of magnesium vanadates and pointed out MgV {sub 2}O{sub 6} has a very short excited electron lift-time. Mg{sub 2}V {sub 2}O{sub 7} performs high photocatalytic activity because of its high electron mobility and long electron life-time.

  5. Stability constants and thermodynamic data for complexes of 12-crown-4 with alkali metal and alkaline-earth cations in methanol solutions

    SciTech Connect

    Buschmann, H.

    1987-03-01

    The formation of 1:1- and 2:1-complexes of the crown ether 12C4 with mono- and bivalent cations was studied in methanol solutions by calorimetric, potentiometric and conductometric titrations. It is shown that not all donor atoms of the ligand 12C4 take part in complex formation. The accuracy of the three experimental methods are checked by comparing the results for the complexation of alkali ions with crown ether 18C6.

  6. Ion permeation through single channels activated by acetylcholine in denervated toad sartorius skeletal muscle fibers: effects of alkali cations.

    PubMed

    Quartararo, N; Barry, P H; Gage, P W

    1987-01-01

    The gigaohm seal technique was used to study ion permeation through acetylcholine-activated channels in cell-attached patches of the extrajunctional membrane of chronically denervated, enzyme-treated cells from the sartorius muscle of the toad Bufo marinus. The most frequently occurring channel type (greater than 95% of channel openings), provisionally classified as 'extrajunctional,' had a chord conductance of approximately 25 pS under normal conditions (-70 mV, 11 degrees C, Normal Toad Ringer's). The less frequently observed channel type (less than 5% of channel openings), classified as a 'junctional' type, had a conductance of 35 pS under the same conditions, and a similar null potential. In many patches, a small percentage (usually less than 2%) of openings of the extrajunctional channel displayed a lower conductance state. The shape of the I-V curves obtained for the extrajunctional channel depended on the predominant extracellular cation. For Cs and K, the I-V curves were essentially linear over the voltage range +50 to -150 mV across the patch, suggesting that the potential independent component of the energy profile within the channel was symmetrical. For Li, the I-V curve was very nonlinear, displaying a significant sublinearity at hyperpolarized potentials. Both an electrodiffusion and a symmetrical uniform four-barrier, three-site rate-theory model provided reasonable fits to the data, whereas symmetrical two-barrier, single-site rate-theory models did not. For the alkali cations examined, the relative permeability sequence was PCs greater than PK greater than PNa greater than PLi--a "proportional" selectivity sequence. This was different from the single channel conductance sequence which was found to be gamma K greater than gamma Cs greater than gamma Na greater than gamma Li implying that ions do not move independently through the channel. The relative binding constant sequence for the channel sites was found to be a "polarizability" sequence, i

  7. Bisphenols that stimulate cells to release alkali metal cations: a structure-activity study.

    PubMed

    Hopp, L; Megee, S O; Lloyd, J B

    1998-10-22

    The laxative action of phenolphthalein (5) is believed to result from induction of potassium and water efflux from the colon epithelium. In cultured cells, K+ efflux is promoted by 5 and by a contaminant (1) present in commercial phenol red. Six compounds with chemical structures related to those of 5 and 1 were tested for ability to induce the release of 86Rb from COS-7 cells preloaded with this isotope: 4,4'-(9-fluorenylidene)diphenol (2), 4, 4'-(9-fluorenylidene)dianiline, 4, 4'-(9-fluorenylidene)bisphenoxyethanol, 1,1'-bi-2-naphthol, 4, 4'-biphenol, and bis(4-hydroxyphenyl)methane. With one exception these compounds were all inactive at a concentration of 10 microM. However, 2 caused profound 86Rb efflux at concentrations as low as 100 nM. Concentrations of 5 1-2 orders of magnitude higher were needed to achieve similar levels of activity. The three compounds known to be active in this experimental system share a common feature that is absent in all the inactive compounds: a five-membered ring structure, one of whose carbon atoms is disubstituted with p-hydroxyphenyl residues. Because 2 and 5 are readily available, comparative studies on the mechanism of action of these biphenols at the cellular level can now be undertaken. PMID:9784117

  8. Cationic RAFT polymerization using ppm concentrations of organic acid.

    PubMed

    Uchiyama, Mineto; Satoh, Kotaro; Kamigaito, Masami

    2015-02-01

    A metal-free, cationic, reversible addition-fragmentation chain-transfer (RAFT) polymerization was proposed and realized. A series of thiocarbonylthio compounds were used in the presence of a small amount of triflic acid for isobutyl vinyl ether to give polymers with controlled molecular weight of up to 1×10(5) and narrow molecular-weight distributions (Mw /Mn <1.1). This "living" or controlled cationic polymerization is applicable to various electron-rich monomers including vinyl ethers, p-methoxystyrene, and even p-hydroxystyrene that possesses an unprotected phenol group. A transformation from cationic to radical RAFT polymerization enables the synthesis of block copolymers between cationically and radically polymerizable monomers, such as vinyl ether and vinyl acetate or methyl acrylate. PMID:25511364

  9. Three Alkali-Metal-Gold-Gallium Systems. Ternary Tunnel Structures and Some Problems with Poorly Ordered Cations

    SciTech Connect

    Smetana, Volodymyr; Miller, Gordon J.; Corbett, John D.

    2012-06-27

    Six new intermetallic compounds have been characterized in the alkali metal (A = Na, Rb, Cs)–gold–gallium systems. Three isostructural compounds with the general composition A0.55Au2Ga2, two others of AAu3Ga2 (A = Rb, Cs), and the related Na13Au41.2Ga30.3 were synthesized via typical high-temperature reactions and their crystal structures determined by single-crystal X-ray diffraction analysis: Na0.56(9)Au2Ga2 (I, I4/mcm, a = 8.718(1) Å, c = 4.857(1) Å, Z = 4), Rb0.56(1)Au2Ga2 (II, I4/mcm, a = 8.950(1) Å, c = 4.829(1) Å, Z = 4), Cs0.54(2)Au2Ga2 (III, I4/mcm, a = 9.077(1) Å, c = 4.815(1) Å, Z = 4), RbAu3Ga2 (IV, Pnma, a = 13.384(3) Å, b = 5.577(1) Å, c = 7.017(1) Å, Z = 4), CsAu3Ga2 (V, Pnma, a = 13.511(3) Å, b = 5.614(2) Å, c = 7.146(1) Å, Z = 4), Na13Au41.2(1)Ga30.3(1) (VI, P6 mmm, a = 19.550(3) Å, c = 8.990(2) Å, Z = 2). The first three compounds (I–III) are isostructural with tetragonal K0.55Au2Ga2 and likewise contain planar eight-member Au/Ga rings that stack along c to generate tunnels and that contain varying degrees of disordered Na–Cs cations. The cation dispositions are much more clearly and reasonably defined by electron density mapping than through least-squares refinements with conventional anisotropic ellipsoids. Orthorhombic AAu3Ga2 (IV, V) are ordered ternary Rb and Cs derivatives of the SrZn5 type structure, demonstrating structural variability within the AAu3Ga2 family. All attempts to prepare an isotypic “NaAu3Ga2” were not successful, but yielded only a similar composition Na13Au41.2Ga30.3 (NaAu3.17Ga2.33) (VI) in a very different structure with two types of cation sites. Crystal orbital Hamilton population (COHP) analysis obtained from tight-binding electronic structure calculations for idealized I–IV via linear muffin-tin-orbital (LMTO) methods emphasized the major contributions of heteroatomic Au–Ga bonding to the structural stability of these compounds. The relative minima (pseudogaps) in the DOS curves for IV

  10. Cation-pi interactions as a mechanism in technical lignin adsorption to cationic surfaces.

    PubMed

    Pillai, Karthik V; Renneckar, Scott

    2009-04-13

    The assembly of dissolved technical lignins in aqueous and organic medium has been studied at the solid-liquid interface. Adsorption of alkali lignin onto gold coated crystals treated with a cationic polymer was determined using a quartz crystal microbalance with dissipation monitoring. Complete coverage of the cationic surface with alkali lignin occurred at low solution concentration, revealing a high affinity coefficient under both alkali and neutral conditions. With additional adsorption studies from organosolv lignin in organic solvent and spectroscopic analysis of mixtures of cationic polymer and alkali lignin, a noncovalent interaction between lignin's aromatic rings and the cation of the quaternary ammonium group was shown to exist. The work underscores how polyphenolic biopolymers can strongly interact with cations through noncovalent interactions to control molecular architecture. PMID:19226174

  11. Separation of alkali, alkaline earth and rare earth cations by liquid membranes containing macrocyclic carriers. Fourth progress report, 1 November 1981-31 July 1982

    SciTech Connect

    Christensen, J J; Izatt, R M

    1982-07-31

    The H/sub 2/O-CHCl/sub 3/-H/sub 2/O liquid membrane system was characterized with respect to the effect on cation (K/sup +/) transport rate of salt concentration and anion type. A bulk liquid membrane cell was used. A mathematical model for cation flux is being developed for several cations, several macrocycles, and mixtures of two or three cations. Eu/sup 3 +/ was not transported by 18-crown-6, but its reduced from Eu/sup 2 +/ was. Cation transport properties of calixarenes are also being investigated. Emulsion membrane systems were studied as a way of increasing the cation transport. Pb/sup 2 +/ was found to be transported by dicyclohexano-18-crown-6 through the liquid membrane. Transport rates of metal cation nitrates were measured in a water-toluene-water emulsion membrane system. 14 figures, 7 tables. (DLC)

  12. Different Cation Arrangements in Au-In Networks. Syntheses and Structures of Six Intermetallic Compounds in Alkali-Metal-Au-In Systems

    SciTech Connect

    Bin Li; John D. Corbett

    2007-06-20

    Six robust intermetallic compounds with cations in three different tunnel-like structures have been synthesized in alkali-metal-Au-In systems via high-temperature solid-state methods and characterized by X-ray diffraction: AAu{sub 4}-In{sub 6} [A = K (I), Rb (II), F6m2, Z = 1], K{sub 1.76(6)}Au{sub 6}Ln{sub 4} (III,; 4/mcm, Z = 4), and A{sub x}Au{sub 2}In{sub 2} [x{approx} 0.7, A = K (IV), Rb (V), Cs (VI), P4{sub 2}/nmc, Z = 8]. The first type is constructed from a single cage unit: an alkali-metal-centered 21-vertex polyhedron A@AugIn12 with 6-9-6 arrangement of planar rings. The others contain uniaxial arrays of tunnels built of differently puckered eight- and four-member Au/In rings. The largely different cation distributions depend on the tunnel constitutions and cation sizes. Tight-binding electronic structure calculations by linear muffin-tin-orbital (LMTO) methods were performed for I and idealized III in order to help understand their chemical bonding. These also reveal large differences in relativistic effects for Au d orbitals, as well as for different Au sites in each structure.

  13. Different Cation Arrangements in Au-In Networks. Syntheses and Structures of Six Intermetallic compounds in Alkali-Metal-Au-In Systems

    SciTech Connect

    Li, Bin; Corbett, John D.

    2007-06-20

    Six robust intermetallic compounds with cations in three different tunnel-like structures have been synthesized in alkali-metal-Au-In systems via high-temperature solid-state methods and characterized by X-ray diffraction: AAu{sub 4}-In{sub 6} [A = K (I), Rb (II), F6m2, Z = 1], K{sub 1.76(6)}Au{sub 6}Ln{sub 4} (III, /4/mcm, Z = 4), and A{sub x}Au{sub 2}In{sub 2} [x {approx} 0.7, A = K (IV), Rb (V), Cs (VI), P4{sub 2}/nmc, Z = 8]. The first type is constructed from a single cage unit: an alkali-metal-centered 21-vertex polyhedron A{at}AugIn{sub 12} with 6-9-6 arrangement of planar rings. The others contain uniaxial arrays of tunnels built of differently puckered eight- and four-member Au/In rings. The largely different cation distributions depend on the tunnel constitutions and cation sizes. Tight-binding electronic structure calculations by linear muffin-tin-orbital (LMTO) methods were performed for I and idealized III in order to help understand their chemical bonding. These also reveal large differences in relativistic effects for Au d orbitals, as well as for different Au sites in each structure.

  14. Ab initio many-electron study for the low-lying states of the alkali hydride cations in the adiabatic representation

    NASA Astrophysics Data System (ADS)

    Yan, Lingling; Qu, Yizhi; Liu, Chunhua; Wang, Jianguo; Buenker, Robert J.

    2012-03-01

    An ab initio multireference single- and double-excitation configuration interaction (CI) study is carried out for the ground and excited electronic states of alkali-hydride cations (LiH+, NaH+, KH+, RbH+, and CsH+). For all alkali-metal atoms, the first inner-shell and valence electrons (nine active electrons, three for Li) are considered explicitly in the ab initio self-consistent-field and CI calculations. The adiabatic potential energy curves, radial and rotational couplings are calculated and presented. Short-range (˜3 a.u.) potential wells produced by the excitation of the inner-shell electrons are found. The depths of the inner potential wells are much greater than those of the outer wells for the CsH+ system. The computed spectroscopic constants for the long-range potential well of the 2 2Σ+ state are very close to the available theoretical and experimental data. The electronic states of alkali-hydrogen cations are also compared with each other, it is found that the positions of the potential wells shift to larger internuclear distances gradually, and the depths of these potential wells become greater with increasing alkali-metal atomic number. The relationships between structures of the radial coupling matrix elements and the avoiding crossings of the potential curves are analyzed. From NaH+ to CsH+, radial coupling matrix elements display more and more complex structures due to the gradual decrease of energy separations for avoided crossings. Finally, the behavior of some rotational couplings is also shown.

  15. The effect of chronic osmotic disturbance on the concentrations of cations in cerebrospinal fluid.

    PubMed

    Bradbury, M W; Kleeman, C R

    1969-09-01

    1. Adult cats were rendered hypo- and hypernatraemic by peritoneal dialysis. These states were maintained for periods of 2-5 days.2. The concentrations in cerebrospinal fluid (c.s.f.) of the cations, potassium, calcium and magnesium all decreased in the hyponatraemic animals and increased in the hypernatraemic animals. These shifts in c.s.f. cation concentrations did not relate to plasma changes in the same cations, which were often in the opposite direction.3. The relations of the cation concentrations to c.s.f. sodium were not linear and, in the cases of calcium and magnesium, the relevant cation concentration related better to the square rather than the first power of the c.s.f. sodium concentration.4. Brain water changed much less in the hypo- and hypernatraemic animals than might be anticipated from the shifts in blood osmolarity, plasma sodium concentration and muscle water.5. Isotonicity of the fluids in brain with blood plasma and c.s.f. appeared to be largely maintained by loss or gain of sodium and chloride ions by this tissue.6. The c.s.f. results may be partly due to a constant influx of the cation in question being diluted with more formed c.s.f. in hyponatraemia and less c.s.f. in hypernatraemia, but the deviations from linearity in the plots of c.s.f. cation against c.s.f. sodium suggest the influence of other factors. PMID:5352043

  16. Structures of Hydrated Alkali Metal Cations, M+(H2O)nAr (m = Li, Na, K, rb and Cs, n = 3-5), Using Infrared Photodissociation Spectroscopy and Thermodynamic Analysis

    NASA Astrophysics Data System (ADS)

    Ke, Haochen; van der Linde, Christian; Lisy, James M.

    2014-06-01

    Alkali metal cations play vital roles in chemical and biochemical systems. Lithium is widely used in psychiatric treatment of manic states and bipolar disorder; Sodium and potassium are essential elements, having major biological roles as electrolytes, balancing osmotic pressure on body cells and assisting the electroneurographic signal transmission; Rubidium has seen increasing usage as a supplementation for manic depression and depression treatment; Cesium doped compounds are used as essential catalysts in chemical production and organic synthesis. Since hydrated alkali metal cations are ubiquitous and the basic form of the alkali metal cations in chemical and biochemical systems, their structural and thermodynamic properties serve as the foundation for modeling more complex chemical and biochemical processes, such as ion transport and ion size-selectivity of ionophores and protein channels. By combining mass spectrometry and infrared photodissociation spectroscopy, we have characterized the structures and thermodynamic properties of the hydrated alkali metal cations, i.e. M+(H2O)nAr, (M = Li, Na, K, Rb and Cs, n = 3-5). Ab initio calculations and RRKM-EE (evaporative ensemble) calculations were used to assist in the spectral assignments and thermodynamic analysis. Results showed that the structures of hydrated alkali metal cations were determined predominantly by the competition between non-covalent interactions, i.e. the water---water hydrogen bonding interactions and the water---cation electrostatic interactions. This balance, however, is very delicate and small changes, i.e. different cations, different levels of hydration and different effective temperatures clearly impact the balance.

  17. Base cation concentrations in subsurface flow from a forested hillslope: The role of flushing frequency

    USGS Publications Warehouse

    Burns, Douglas A.; Hooper, R.P.; McDonnell, Jeffery J.; Freer, J.E.; Kendall, C.; Beven, K.

    1998-01-01

    A 20-m-wide trench was excavated to bedrock on a hillslope at the Panola Mountain Research Watershed in the Piedmont region of Georgia to determine the effect of upslope drainage area from the soil and bedrock surfaces on the geochemical evolution of base cation concentrations in subsurface flow. Samples were collected from ten 2-m sections and five natural soil pipes during three winter rainstorms in 1996. Base cation concentrations in hillslope subsurface flow were generally highest early and late in the storm response when flow rates were low, but during peak flow, concentrations varied little. Base cation concentrations in matrix flow from the 10 trench sections were unrelated to the soil surface drainage area and weakly inversely related to the bedrock surface drainage area. Base cation concentrations in pipe flow were lower than those in matrix flow and were also consistent with the inverse relation to bedrock surface drainage area found in matrix flow. The left side of the trench, which has the highest bedrock surface drainage area, had consistently lower mean base cation concentrations than the right side of the trench, which has the lowest bedrock surface drainage area. During moderate size rain events of about 20-40 mm, subsurface flow occurred only on the left side of the trench. The greater volume of water that has flowed through the left side of the trench appears to have resulted in greater leaching of base cations from soils and therefore lower base cation concentrations in subsurface flow than in flow from the right side of the trench. Alternatively, a greater proportion of flow that bypasses the soil matrix may have occurred through the hillslope on the left side of the trench than on the right side. Flushing frequency links spatial hillslope water flux with the evolution of groundwater and soil chemistry.

  18. Selectivity of externally facing ion-binding sites in the Na/K pump to alkali metals and organic cations.

    PubMed

    Ratheal, Ian M; Virgin, Gail K; Yu, Haibo; Roux, Benoît; Gatto, Craig; Artigas, Pablo

    2010-10-26

    The Na/K pump is a P-type ATPase that exchanges three intracellular Na(+) ions for two extracellular K(+) ions through the plasmalemma of nearly all animal cells. The mechanisms involved in cation selection by the pump's ion-binding sites (site I and site II bind either Na(+) or K(+); site III binds only Na(+)) are poorly understood. We studied cation selectivity by outward-facing sites (high K(+) affinity) of Na/K pumps expressed in Xenopus oocytes, under voltage clamp. Guanidinium(+), methylguanidinium(+), and aminoguanidinium(+) produced two phenomena possibly reflecting actions at site III: (i) voltage-dependent inhibition (VDI) of outwardly directed pump current at saturating K(+), and (ii) induction of pump-mediated, guanidinium-derivative-carried inward current at negative potentials without Na(+) and K(+). In contrast, formamidinium(+) and acetamidinium(+) induced K(+)-like outward currents. Measurement of ouabain-sensitive ATPase activity and radiolabeled cation uptake confirmed that these cations are external K(+) congeners. Molecular dynamics simulations indicate that bound organic cations induce minor distortion of the binding sites. Among tested metals, only Li(+) induced Na(+)-like VDI, whereas all metals tested except Na(+) induced K(+)-like outward currents. Pump-mediated K(+)-like organic cation transport challenges the concept of rigid structural models in which ion specificity at site I and site II arises from a precise and unique arrangement of coordinating ligands. Furthermore, actions by guanidinium(+) derivatives suggest that Na(+) binds to site III in a hydrated form and that the inward current observed without external Na(+) and K(+) represents cation transport when normal occlusion at sites I and II is impaired. These results provide insights on external ion selectivity at the three binding sites. PMID:20937860

  19. Electrical conduction in alkali borate glasses; a unique dependence on the concentration of modifier ions

    NASA Astrophysics Data System (ADS)

    Doweidar, H.; Moustafa, Y. M.; El-Damrawi, G. M.; Ramadan, R. M.

    2008-01-01

    The electrical conduction of Li2O-B2O3, Na2O-B2O3 and K2O-B2O3 glasses seems, at first sight, to be dominated by the activation energy. Regardless of the size of the alkali ion, there is a unique dependence of conductivity, at a certain temperature, on the alkali-alkali distance and thus on N (the number of ions per cm3). The linear dependence of logσ on N-3/2 for all types of alkali ions reveals that N is the basic parameter that determines the conductivity at a certain temperature. A derived semi-empirical relation can be used to calculate the conductivity as a function of N and temperature.

  20. The effect of cation source and dietary cation-anion difference on rumen ion concentrations in lactating dairy cows.

    PubMed

    Catterton, T L; Erdman, R A

    2016-08-01

    Many studies have focused on the influence of dietary cation-anion difference (DCAD) on animal performance but few have examined the effect of DCAD on the rumen ionic environment. The objective of this study was to examine the effects of DCAD, cation source (Na vs. K), and anion source (Cl vs. bicarbonate or carbonate) on rumen environment and fermentation. The study used 5 rumen-fistulated dairy cows and 5 dietary treatments that were applied using a 5×5 Latin square design with 2-wk experimental periods. Treatments consisted of (1) the basal total mixed ration (TMR); (2) the basal TMR plus 340mEq/kg of Na (dry matter basis) using NaCl; (3) the basal TMR plus 340mEq/kg of K using KCl; (4) the basal TMR plus 340mEq/kg of Na using NaHCO3; and (5) the basal TMR plus 340mEq/kg of K using K2CO3. On the last day of each experimental period, rumen samples were collected and pooled from 5 different locations at 0, 1.5, 3, 4.5, 6, 9, and 12h postfeeding for measurement of rumen pH and concentrations of strong ions and volatile fatty acids (VFA). Dietary supplementation of individual strong ions increased the corresponding rumen ion concentration. Rumen Na was decreased by 24mEq/L when K was substituted for Na in the diet, but added dietary Na had no effect on rumen K. Rumen Cl was increased by 10mEq/L in diets supplemented with Cl. Cation source had no effect on rumen pH or total VFA concentration. Increased DCAD increased rumen pH by 0.10 pH units and increased rumen acetate by 4mEq/L but did not increase total VFA. This study demonstrated that rumen ion concentrations can be manipulated by dietary ion concentrations. If production and feed efficiency responses to DCAD and ionophores in the diet are affected by rumen Na and K concentrations, then manipulating dietary Na and K could be used either to enhance or diminish those responses. PMID:27289159

  1. Determination of flue gas alkali concentrations in fluidized-bed coal combustion by excimer-laser-induced fragmentation fluorescence

    SciTech Connect

    Hartinger, K.T.; Monkhouse, P.B.; Wolfrum, J.; Baumann, H.; Bonn, B.

    1994-12-31

    Gas-phase sodium concentrations were measured for the first time in situ in the flue gas of a fluidized-bed reactor by the excimer-laser-induced fragmentation fluorescence (ELIF) technique. This method involves using ArF-excimer laser light at 193 nm to simultaneously photodissociate the alkali compounds of interest and excite electronically the alkali atoms formed. The resulting fluorescence from Na (3{sup 2}P) atoms can he readily detected at 589 nm. Measured signals were converted to absolute concentrations using a calibration system that monitors alkali compounds under known conditions of temperature, pressure, and composition and rising the same optical setup as at the reactor. Several different coals were investigated under a specific set of reactor conditions at total pressures close to 1 bar. Sodium concentrations ranging from the sub-ppb region to 20 ppb were obtained, and a detection limit for sodium of 0.1 ppb under the present conditions was estimated. Over the course of the reactor program, contrasting concentration histories were observed for the two lignites and the hard coal investigated. In particular, significantly higher sodium concentrations were found for the hard coal, consistent with both the higher chlorine and sodium contents determined in the corresponding coal analysis.

  2. Bonding and singlet-triplet gap of silicon trimer: effects of protonation and attachment of alkali metal cations.

    PubMed

    Tam, Nguyen Minh; Hang, Tran Dieu; Pham, Hung Tan; Nguyen, Huyen Thi; Pham-Ho, My Phuong; Denis, Pablo A; Nguyen, Minh Tho

    2015-04-30

    We revisit the singlet-triplet energy gap (ΔE(ST)) of silicon trimer and evaluate the gaps of its derivatives by attachment of a cation (H(+), Li(+), Na(+), and K(+)) using the wavefunction-based methods including the composite G4, coupled-cluster theory CCSD(T)/CBS, CCSDT and CCSDTQ, and CASSCF/CASPT2 (for Si3) computations. Both (1)A1 and (3)A2' states of Si3 are determined to be degenerate. An intersystem crossing between both states appears to be possible at a point having an apex bond angle of around α = 68 ± 2° which is 16 ± 4 kJ/mol above the ground state. The proton, Li(+) and Na(+) cations tend to favor the low-spin state, whereas the K(+) cation favors the high-spin state. However, they do not modify significantly the ΔE(ST). The proton affinity of silicon trimer is determined as PA(Si3) = 830 ± 4 kJ/mol at 298 K. The metal cation affinities are also predicted to be LiCA(Si3) = 108 ± 8 kJ/mol, NaCA(Si3) = 79 ± 8 kJ/mol and KCA(Si3) = 44 ± 8 kJ/mol. The chemical bonding is probed using the electron localization function, and ring current analyses show that the singlet three-membered ring Si3 is, at most, nonaromatic. Attachment of the proton and Li(+) cation renders it anti-aromatic. PMID:25694392

  3. Specific interactions between alkali metal cations and the KcsA channel studied using ATR-FTIR spectroscopy

    PubMed Central

    Furutani, Yuji; Shimizu, Hirofumi; Asai, Yusuke; Oiki, Shigetoshi; Kandori, Hideki

    2015-01-01

    The X-ray structure of KcsA, a eubacterial potassium channel, displays a selectivity filter composed of four parallel peptide strands. The backbone carbonyl oxygen atoms of these strands solvate multiple K+ ions. KcsA structures show different distributions of ions within the selectivity filter in solutions containing different cations. To assess the interactions of cations with the selectivity filter, we used attenuated total reflection Fourier-transform infrared (ATR-FTIR) spectroscopy. Ion-exchange-induced ATR-FTIR difference spectra were obtained by subtracting the spectrum of KcsA soaked in K+ solution from that obtained in Li+, Na+, Rb+, and Cs+ solutions. Large spectral changes in the amide-I and -II regions were observed upon replacing K+ with smaller-sized cations Li+ and Na+ but not with larger-sized cations Rb+ and Cs+. These results strongly suggest that the selectivity filter carbonyls coordinating Rb+ or Cs+ adopt a conformation similar to those coordinating K+ (cage configuration), but those coordinating Li+ or Na+ adopt a conformation (plane configuration) considerably different from those coordinating K+. We have identified a cation-type sensitive amide-I band at 1681 cm−1 and an insensitive amide-I band at 1659 cm−1. The bands at 1650, 1639, and 1627 cm−1 observed for Na+-coordinating carbonyls were almost identical to those observed in Li+ solution, suggesting that KcsA forms a similar filter structure in Li+ and Na+ solutions. Thus, we conclude that the filter structure adopts a collapsed conformation in Li+ solution that is similar to that in Na+ solution but is in clear contrast to the X-ray crystal structure of KcsA with Li+. PMID:27493853

  4. Influence of cationic lipid concentration on properties of lipid–polymer hybrid nanospheres for gene delivery

    PubMed Central

    Bose, Rajendran JC; Arai, Yoshie; Ahn, Jong Chan; Park, Hansoo; Lee, Soo-Hong

    2015-01-01

    Nanoparticles have been widely used for nonviral gene delivery. Recently, cationic hybrid nanoparticles consisting of two different materials were suggested as a promising delivery vehicle. In this study, nanospheres with a poly(d,l-lactic-co-glycolic acid) (PLGA) core and cationic lipid shell were prepared, and the effect of cationic lipid concentrations on the properties of lipid polymer hybrid nanocarriers investigated. Lipid–polymer hybrid nanospheres (LPHNSs) were fabricated by the emulsion-solvent evaporation method using different concentrations of cationic lipids and characterized for size, surface charge, stability, plasmid DNA-binding capacity, cytotoxicity, and transfection efficiency. All LPHNSs had narrow size distribution with positive surface charges (ζ-potential 52–60 mV), and showed excellent plasmid DNA-binding capacity. In vitro cytotoxicity measurements with HEK293T, HeLa, HaCaT, and HepG2 cells also showed that LPHNSs exhibited less cytotoxicity than conventional transfection agents, such as Lipofectamine and polyethyleneimine–PLGA. As cationic lipid concentrations increased, the particle size of LPHNSs decreased while their ζ-potential increased. In addition, the in vitro transfection efficiency of LPHNSs increased as lipid concentration increased. PMID:26379434

  5. Characterization of selective binding of alkali cations with carboxylate by x-ray absorption spectroscopy of liquid microjets

    SciTech Connect

    Saykally, Richard J; Uejio, Janel S.; Schwartz, Craig P.; Duffin, Andrew M.; Drisdell, Walter S.; Cohen, Ronald C.; Saykally, Richard J.

    2008-01-08

    We describe an approach for characterizing selective binding between oppositely charged ionic functional groups under biologically relevant conditions. Relative shifts in K-shell x-ray absorption spectra of aqueous cations and carboxylate anions indicate the corresponding binding strengths via perturbations of carbonyl antibonding orbitals. XAS spectra measured for aqueous formate and acetate solutions containing lithium, sodium, and potassium cations reveal monotonically stronger binding of the lighter metals, supporting recent results from simulations and other experiments. The carbon K-edge spectra of the acetate carbonyl feature centered near 290 eV clearly indicate a preferential interaction of sodium versus potassium, which was less apparent with formate. These results are in accord with the Law of Matching Water Affinities, relating relative hydration strengths of ions to their respective tendencies to form contact ion pairs. Density functional theory calculations of K-shell spectra support the experimental findings.

  6. Dimethyl sulfoxide at high concentrations inhibits non-selective cation channels in human erythrocytes.

    PubMed

    Nardid, Oleg A; Schetinskey, Miroslav I; Kucherenko, Yuliya V

    2013-03-01

    Dimethyl sulfoxide (DMSO), a by-product of the pulping industry, is widely used in biological research, cryobiology and medicine. On cellular level DMSO was shown to suppress NMDA-AMPA channels activation, blocks Na+ channel activation and attenuates Ca2+ influx (Lu and Mattson 2001). In the present study we explored the whole-cell patch-clamp to examine the acute effect of high concentrations of DMSO (0.1-2 mol/l) on cation channels activity in human erythrocytes. Acute application of DMSO (0.1-2 mol/l) dissolved in Cl--containing saline buffer solution significantly inhibited cation conductance in human erythrocytes. Inhibition was concentration-dependent and had an exponential decay profile. DMSO (2 mol/l) induced cation inhibition in Cl-- containing saline solutions of: 40.3 ± 3.9% for K+, 35.4 ± 3.1% for Ca2+ and 47.4 ± 1.9% for NMDG+. Substitution of Cl- with gluconate- increased the inhibitory effect of DMSO on the Na+ current. Inhibitory effect of DMSO was neither due to high permeability of erythrocytes to DMSO nor to an increased tonicity of the bath media since no effect was observed in 2 mol/l glycerol solution. In conclusion, we have shown that high concentrations of DMSO inhibit the non-selective cation channels in human erythrocytes and thus protect the cells against Na+ and Ca2+ overload. Possible mechanisms of DMSO effect on cation conductance are discussed. PMID:23531832

  7. Control of cation concentrations in stream waters by surface soil processes in an Amazonian watershed.

    PubMed

    Markewitz, D; Davidson, E A; Figueiredo Rd; Victoria, R L; Krusche, A V

    2001-04-12

    The chemical composition of ground waters and stream waters is thought to be determined primarily by weathering of parent rock. In relatively young soils such as those occurring in most temperate ecosystems, dissolution of primary minerals by carbonic acid is the predominant weathering pathway that liberates Ca2+, Mg2+ and K+ and generates alkalinity in the hydrosphere. But control of water chemistry in old and highly weathered soils that have lost reservoirs of primary minerals (a common feature of many tropical soils) is less well understood. Here we present soil and water chemistry data from a 10,000-hectare watershed on highly weathered soil in the Brazilian Amazon. Streamwater cation concentrations and alkalinity are positively correlated to each other and to streamwater discharge, suggesting that cations and bicarbonate are mainly flushed from surface soil layers by rainfall rather than being the products of deep soil weathering carried by groundwater flow. These patterns contrast with the seasonal patterns widely recognized in temperate ecosystems with less strongly weathered soils. In this particular watershed, partial forest clearing and burning 30 years previously enriched the soils in cations and so may have increased the observed wet season leaching of cations. Nevertheless, annual inputs and outputs of cations from the watershed are low and nearly balanced, and thus soil cations from forest burning will remain available for forest regrowth over the next few decades. Our observations suggest that increased root and microbial respiration during the wet season generates CO2 that drives cation-bicarbonate leaching, resulting in a biologically mediated process of surface soil exchange controlling the streamwater inputs of cations and alkalinity from these highly weathered soils. PMID:11298445

  8. Hydration thermodynamics of the SWy-1 montmorillonite saturated with alkali and alkaline-earth cations: A predictive model

    NASA Astrophysics Data System (ADS)

    Vieillard, Philippe; Blanc, Philippe; Fialips, Claire I.; Gailhanou, Hélène; Gaboreau, Stéphane

    2011-10-01

    The aim of the present work was to study the thermodynamic equilibria between water and a homo-ionic montmorillonite SWy-1 saturated by different cations. The choice of this smectite is justified by the large set of experimental data available from the literature for eight different interlayer cations: Na +, K +, Rb +, Cs +, Mg 2+, Ca 2+, Sr 2+, and Ba 2+. In particular, studies by Cases et al. (1992, 1997) and Bérend et al. (1995) are providing heat of adsorption data, pairs of desorption-adsorption isotherms, and information about the partition of adsorption-desorption water molecules between external surfaces and internal spaces. By calculating the effective amount of hydration water as the difference between the so-called gravimetric water and the surface covering water, a thermodynamic model was then developed, based on the concept of Ransom and Helgeson (1994) considering an asymmetric subregular binary solid solution between a fully hydrated and a anhydrous smectite. A set of six thermodynamic parameters ( ΔH∘hyd,S∘hyd and four Margules parameters) was extracted by a least square method from measurements of enthalpies of adsorption and paired adsorption-desorption isotherms for each interlayer cation. These six initial parameters were then used to determine a complete set of standard thermodynamic hydration parameters ( ΔH∘hyd,ΔG∘hyd,ΔS∘hyd, heat capacity, molar volume, and number of interlayer H 2O) and quantify, for each cation, the number of moles of hydration water molecules as a function of relative humidity and temperature. The validation of the standard state thermodynamic properties of hydration for each end member was carried out using three approaches: (1) a comparison with experimental isotherms obtained on hetero-ionic and homo-ionic SWy-1 smectite at different temperatures; (2) a comparison with the experimental integral enthalpy and entropy of hydration of the SWy-1 smectite; and (3) a comparison with experimental isotherms

  9. Emission spectrographic determination of barium in sea water using a cation exchange concentration procedure

    USGS Publications Warehouse

    Szabo, B. J.; Joensuu, O.

    1967-01-01

    A concentration technique employing Dowex 50W cation exchange resin is described for the determination of barium in sea water. The separated barium is precipitated as fluoride together with calcium and strontium and measured by emission spectrographic analysis. The vertical distribution of barium in sea water has been measured in the Caribbean Sea and the Atlantic Ocean. The barium content varied between 7 and 23 ??g. per liter; in two profiles, the lowest concentrations were at a depth of about 1000 meters.

  10. A multinuclear solid-state NMR study of alkali metal ions in tetraphenylborate salts, M[BPh4] (M = Na, K, Rb and Cs): what is the NMR signature of cation-pi interactions?

    PubMed

    Wu, Gang; Terskikh, Victor

    2008-10-16

    We report a multinuclear solid-state ( (23)Na, (39)K, (87)Rb, (133)Cs) NMR study of tetraphenylborate salts, M[BPh 4] (M = Na, K, Rb, Cs). These compounds are isostructural in the solid state with the alkali metal ion surrounded by four phenyl groups resulting in strong cation-pi interactions. From analyses of solid-state NMR spectra obtained under stationary and magic-angle spinning (MAS) conditions at 11.75 and 21.15 T, we have obtained the quadrupole coupling constants, C Q, and the chemical shift tensor parameters for the alkali metal ions in these compounds. We found that the observed quadrupole coupling constant for M (+) in M[BPh 4] is determined by a combination of nuclear quadrupole moment, Sternheimer antishielding factor, and unit cell dimensions. On the basis of a comparison between computed paramagnetic and diamagnetic contributions to the total chemical shielding values for commonly found cation-ligand interactions, we conclude that cation-pi interactions give rise to significantly lower paramagnetic shielding contributions than other cation-ligand interactions. As a result, highly negative chemical shifts are expected to be the NMR signature for cations interacting exclusively with pi systems. PMID:18816043

  11. Mercury concentrations in marine sediments near a former mercury cell chlor-alkali plant in eastern Canada.

    PubMed

    Walker, Tony R

    2016-06-15

    Concentrations of total mercury (THg) were measured in coastal marine sediments near a former chlor-alkali plant in Chaleur Bay, New Brunswick. The chlor-alkali plant has been a local point source of THg since operation began in 1963. Historical THg contamination of marine sediments and biota has been widely reported. No baseline assessment has been conducted following plant closure in 2008. Surface (0-2cm) oxidized marine sediments were sampled along a single 5.2km transect radiating from the former plant and analysed for THg. THg concentrations ranged from 0.04-0.28μgg(-1). Some localised THg concentrations exceeded Canadian marine sediment quality guidelines (n=4), but all samples (n=14) were significantly lower than previous studies conducted during plant operation. Plant closure (source control) and natural sediment recovery likely responsible for attenuating THg concentrations, but burial in deeper anoxic sediments may increase bioavilability of Hg that could pose ecological risks to marine biota. PMID:27016328

  12. Decondensation behavior of DNA chains induced by multivalent cations at high salt concentrations: Molecular dynamics simulations and experiments

    NASA Astrophysics Data System (ADS)

    Jiang, Yang-Wei; Ran, Shi-Yong; He, Lin-Li; Wang, Xiang-Hong; Zhang, Lin-Xi

    2015-11-01

    Using molecular dynamics simulations and atomic force microscopy (AFM), we study the decondensation process of DNA chains induced by multivalent cations at high salt concentrations in the presence of short cationic chains in solutions. The typical simulation conformations of DNA chains with varying salt concentrations for multivalent cations imply that the concentration of salt cations and the valence of multivalent cations have a strong influence on the process of DNA decondensation. The DNA chains are condensed in the absence of salt or at low salt concentrations, and the compacted conformations of DNA chains become loose when a number of cations and anions are added into the solution. It is explicitly demonstrated that cations can overcompensate the bare charge of the DNA chains and weaken the attraction interactions between the DNA chains and short cationic chains at high salt concentrations. The condensation-decondensation transitions of DNA are also experimentally observed in mixing spermidine with λ-phage DNA at different concentrations of NaCl/MgCl2 solutions. Project supported by the National Natural Science Foundation of China (Grant No. 31340026), the Natural Science Foundation of Zhejiang Province, China (Grant Nos. Z13F20019 and LQ12E01003), and the Science and Technology Project of Zhejiang Science and Technology Department, China (Grant No. 2014C31147).

  13. Metal cation/anion adsorption on calcium carbonate: Implications to metal ion concentrations in groundwater

    SciTech Connect

    Zachara, J.M.; Cowan, C.E.; Resch, C.T.

    1990-05-01

    This chapter evaluates the sorption behavior of metallic ions on specimen calcite as a basis for determining the importance of calcite relative to other subsurface sorbents, such as layer silicates and oxides, in controlling metal ion concentration in calcareous groundwaters. A review of the literature shows the sorption of both metallic cations and anions on calcite over ranges in pH and CO{sub 2} partial pressure to be consistent with a surface-exchange process where cations exchange with surface Ca and anions exchange with surface CO{sub 3}. A general surface-exchange model was developed to account for the effects of Ca and CO{sub 3} concentrations, pH, and calcite surface area on cation and anion sorption onto calcite. The model was applied to recently developed experimental sorption data of Zn and SeO{sub 3} on specimen calcite in equilibrium CaCO{sub 3}(aq) suspensions. The surface-exchange model was able to describe the effects of pH on both cation and anion sorption, and provided good predictions of the effects of variable CO{sub 2}(g) pressure on Zn sorption and of PO{sub 4} on SeO{sub 3} sorption. The surface-exchange model, combined with sorption constants for other phases, was used to calculate Cd sorption to a hypothetical aquifer material containing a mixture of sorbents. The sorbent concentrations were fixed to those expected in groundwater zones. The multi-sorbent calculation documented the importance of calcite as a sorbent for metallic ions in groundwater.93 refs., 18 figs., 5 tabs.

  14. Suppression of Sensitivity to Drugs and Antibiotics by High External Cation Concentrations in Fission Yeast

    PubMed Central

    Shabro, Aidin; Sunnerhagen, Per

    2015-01-01

    Background Potassium ion homeostasis plays an important role in regulating membrane potential and therefore resistance to cations, antibiotics and chemotherapeutic agents in Schizosaccharomyces pombe and other yeasts. However, the precise relationship between drug resistance in S. pombe and external potassium concentrations (particularly in its natural habitats) remains unclear. S. pombe can tolerate a wide range of external potassium concentrations which in turn affect plasma membrane polarization. We thus hypothesized that high external potassium concentrations suppress the sensitivity of this yeast to various drugs. Methods We have investigated the effect of external KCl concentrations on the sensitivity of S. pombe cells to a wide range of antibiotics, antimicrobial agents and chemotherapeutic drugs. We employed survival assays, immunoblotting and microscopy for these studies. Results We demonstrate that KCl, and to a lesser extent NaCl and RbCl can suppress the sensitivity of S. pombe to a wide range of antibiotics. Ammonium chloride and potassium hydrogen sulphate also suppressed drug sensitivity. This effect appears to depend in part on changes to membrane polarization and membrane transport proteins. Interestingly, we have found little relationship between the suppressive effect of KCl on sensitivity and the structure, polarity or solubility of the various compounds investigated. Conclusions High concentrations of external potassium and other cations suppress sensitivity to a wide range of drugs in S. pombe. Potassium-rich environments may thus provide S. pombe a competitive advantage in nature. Modulating potassium ion homeostasis may sensitize pathogenic fungi to antifungal agents. PMID:25793410

  15. X-ray and neutron scattering studies of the hydration structure of alkali ions in concentrated aqueous solutions.

    PubMed

    Ansell, S; Barnes, A C; Mason, P E; Neilson, G W; Ramos, S

    2006-12-01

    The presence of ions in water provides a rich and varied environment in which many natural processes occur with important consequences in biology, geology and chemistry. This article will focus on the structural properties of ions in water and it will be shown how the 'difference' methods of neutron diffraction with isotopic substitution (NDIS) and anomalous X-ray diffraction (AXD) can be used to obtain direct information regarding the radial pair distribution functions of many cations and anions in solution. This information can subsequently be used to calculate coordination numbers and to determine ion-water conformation in great detail. As well as enabling comparisons to be made amongst ions in particular groups in the periodic table, such information can also be contrasted with results provided by molecular dynamics (MD) simulation techniques. To illustrate the power of these 'difference' methods, reference will be made to the alkali group of ions, all of which have been successfully investigated by the above methods, with the exception of the radioactive element francium. Additional comments will be made on how NDIS measurements are currently being combined with MD simulations to determine the structure around complex ions and molecules, many of which are common in biological systems. PMID:16815625

  16. The effect of dietary cation-anion difference concentration and cation source on milk production and feed efficiency in lactating dairy cows.

    PubMed

    Iwaniuk, M E; Weidman, A E; Erdman, R A

    2015-03-01

    Feed costs currently account for 55% or more of the total cost of milk production in US dairy herds, and dairy producers are looking for strategies to improve feed efficiency [FE; 3.5% fat-corrected milk (FCM) per dry matter (DM) intake]. Increasing dietary cation-anion difference [DCAD; Na+K-Cl (mEq/kg of DM)] has been shown to increase milk production, FCM, and FE. However, the optimal DCAD concentration for maximal FE has yet to be determined. The objectives of this research were to test the effects of DCAD concentration and cation source on dairy FE. Sixty Holstein dairy cows (20 cows per experiment) were used in three 4×4 Latin square design experiments with 3-wk experimental periods. In experiments 1 and 2, we tested the effect of DCAD concentration: cows were fed a basal diet containing ~250 mEq/kg of DM DCAD that was supplemented with potassium carbonate at 0, 50, 100, and 150 mEq/kg of DM or 0, 125, 250, and 375 mEq/kg of DM in experiments 1 and 2, respectively. In experiment 3, we tested the effect of cation source: sodium sesquicarbonate replaced 0, 33, 67, and 100% of the supplemental potassium carbonate (150 mEq/kg of DM DCAD). The DCAD concentration had no effect on milk production, milk protein concentration, or milk protein yield in experiments 1 and 2. Dry matter intake was not affected by DCAD concentration in experiment 1 or by cation source in experiment 3. However, DMI increased linearly with increasing DCAD in experiment 2. We detected a linear increase in milk fat concentration and yield with increasing DCAD in experiments 1 and 2 and by substituting sodium sesquicarbonate for potassium carbonate in experiment 3. Increased milk fat concentration with increasing DCAD led to increases in 3.5% FCM in experiments 1 and 2. Maximal dairy FE was achieved at a DCAD concentration of 426 mEq/kg of DM in experiments 1 and 2 and by substituting Na for K in experiment 3. The results of these experiments suggest that both DCAD concentration and the cation

  17. Room-temperature ferroelectricity of SrTiO{sub 3} films modulated by cation concentration

    SciTech Connect

    Yang, Fang; Zhang, Qinghua; Yang, Zhenzhong; Gu, Junxing; Liang, Yan; Li, Wentao; Wang, Weihua; Jin, Kuijuan; Gu, Lin; Guo, Jiandong

    2015-08-24

    The room-temperature ferroelectricity of SrTiO{sub 3} is promising for oxide electronic devices controlled by multiple fields. An effective way to control the ferroelectricity is highly demanded. Here, we show that the off-centered antisite-like defects in SrTiO{sub 3} films epitaxially grown on Si (001) play the determinative role in the emergence of room-temperature ferroelectricity. The density of these defects changes with the film cation concentration sensitively, resulting in a varied coercive field of the ferroelectric behavior. Consequently, the room-temperature ferroelectricity of SrTiO{sub 3} films can be effectively modulated by tuning the temperature of metal sources during the molecular beam epitaxy growth. Such an easy and reliable modulation of the ferroelectricity enables the flexible engineering of multifunctional oxide electronic devices.

  18. Design and synthesis of redox-switched lariat ethers and their application for transport of alkali and alkaline-Earth metal cations across supported liquid membrane.

    PubMed

    Awasthy, Anubhuti; Bhatnagar, Mamta; Tomar, Jyoti; Sharma, Uma

    2006-01-01

    A new class of redox-switched anthraquinone derived lariat ethers 1-(1-anthraquinonyloxy) 3, 6, 9 trioxaundecane 11-ol (M(1)), 1-(1-anthraquinonyloxy) 3, 6 dioxaoctane 9-ol (M(2)), 1-(1-anthraquinonyloxy) 3 oxapentane 5-ol (M(3)), 1-(1-anthraquinonyloxy) 3 oxapentane 5-butane (M(4)), 1-(1-anthraquinonyloxy) 3, 6 dioxaoctane 9-methane (M(5)) and 1-(1-anthraquinonyloxy) 3 oxapentane 5-methane (M(6)) have been synthesized and characterized by spectral analysis. These ionophores were used in liquid membrane carrier facilitated transport of main group metal cations across supported liquid membrane (SLM). Cellulose nitrate membrane was used as membrane support. Effect of various parameters such as variation in concentration of metal as well as ionophore, effect of chain length and end group of ionophore have been studied. The sequence of metal ions transported by ionophore M(1) is Na(+) > Li(+) > K(+) > Ca(2+) > Mg(2+) and the order of metal ions transported by ionophores (M(2)-M(6)) is Li(+) > Na(+) > K(+) > Ca(2+) > Mg(2+). Ionophore M(1) is selective for Na(+), Li(+), and K(+) and ionophores (M(2)-M(6)) are selective for Li(+) and Na(+). PMID:17497021

  19. Analyzing freely dissolved concentrations of cationic surfactant utilizing ion-exchange capability of polyacrylate coated solid-phase microextraction fibers.

    PubMed

    Chen, Yi; Droge, Steven T J; Hermens, Joop L M

    2012-08-24

    A 7-μm polyacrylate (PA) coated fiber was successfully employed to determine freely dissolved concentrations of cationic surfactants by solid-phase microextraction (SPME) and utilizing the capability of the PA-coating to sorb organic cations via ion-exchange at carboxylic groups. Measured fiber-water partitioning coefficients (K(fw)) were constant below a fiber loading of 2mmol per liter polyacrylate, allowing for simple and accurate analysis in a concentration range that is relevant from a risk assessment point of view. Ion-exchange was confirmed to be the main sorption mechanism because of a decreasing K(fw) with either higher CaCl(2) concentrations or lower pH, and maximum fiber uptake at the polyacrylate cation-exchange capacity (CEC, at 30mmol/L PA). Fiber-water sorption isotherms were established in various aqueous media in toxicological relevant concentrations. The developed SPME method has a high potential for application in ecotoxicological studies, as demonstrated in sorption studies with humic acid in different electrolyte solutions at aqueous concentrations down to the sub nM range. Cationic surfactant sorption affinities for humic acid also depend on medium composition but are orders of magnitude higher than to the PA fiber on a sorbent weight basis. PMID:22818738

  20. Determination of lead, cations, and anions concentration in indoor and outdoor air at the primary schools in Kuala Lumpur.

    PubMed

    Awang, Normah; Jamaluddin, Farhana

    2014-01-01

    This study was carried out to determine the concentration of lead (Pb), anions, and cations at six primary schools located around Kuala Lumpur. Low volume sampler (MiniVol PM10) was used to collect the suspended particulates in indoor and outdoor air. Results showed that the concentration of Pb in indoor air was in the range of 5.18 ± 1.08 μg/g-7.01 ± 0.08 μg/g. All the concentrations of Pb in indoor air were higher than in outdoor air at all sampling stations. The concentrations of cations and anions were higher in outdoor air than in indoor air. The concentration of Ca(2+) (39.51 ± 5.01 mg/g-65.13 ± 9.42 mg/g) was the highest because the cation existed naturally in soil dusts, while the concentrations of NO3 (-) and SO4 (2-) were higher in outdoor air because there were more sources of exposure for anions in outdoor air, such as highly congested traffic and motor vehicles emissions. In comparison, the concentration of NO3 (-) (29.72 ± 0.31 μg/g-32.00 ± 0.75 μg/g) was slightly higher than SO4 (2-). The concentrations of most of the parameters in this study, such as Mg(2+), Ca(2+), NO3 (-), SO4 (2-), and Pb(2+), were higher in outdoor air than in indoor air at all sampling stations. PMID:25136371

  1. Determination of Lead, Cations, and Anions Concentration in Indoor and Outdoor Air at the Primary Schools in Kuala Lumpur

    PubMed Central

    Awang, Normah; Jamaluddin, Farhana

    2014-01-01

    This study was carried out to determine the concentration of lead (Pb), anions, and cations at six primary schools located around Kuala Lumpur. Low volume sampler (MiniVol PM10) was used to collect the suspended particulates in indoor and outdoor air. Results showed that the concentration of Pb in indoor air was in the range of 5.18 ± 1.08 μg/g–7.01 ± 0.08 μg/g. All the concentrations of Pb in indoor air were higher than in outdoor air at all sampling stations. The concentrations of cations and anions were higher in outdoor air than in indoor air. The concentration of Ca2+ (39.51 ± 5.01 mg/g–65.13 ± 9.42 mg/g) was the highest because the cation existed naturally in soil dusts, while the concentrations of NO3− and SO42− were higher in outdoor air because there were more sources of exposure for anions in outdoor air, such as highly congested traffic and motor vehicles emissions. In comparison, the concentration of NO3− (29.72 ± 0.31 μg/g–32.00 ± 0.75 μg/g) was slightly higher than SO42−. The concentrations of most of the parameters in this study, such as Mg2+, Ca2+, NO3−, SO42−, and Pb2+, were higher in outdoor air than in indoor air at all sampling stations. PMID:25136371

  2. Dynamics of radical cations of poly(4-hydroxystyrene) in the presence and absence of triphenylsulfonium triflate as determined by pulse radiolysis of its highly concentrated solution

    NASA Astrophysics Data System (ADS)

    Okamoto, Kazumasa; Ishida, Takuya; Yamamoto, Hiroki; Kozawa, Takahiro; Fujiyoshi, Ryoko; Umegaki, Kikuo

    2016-07-01

    Pulse radiolysis of highly concentrated poly(4-hydroxystyrene) (PHS) solutions in cyclohexanone and p-dioxane was performed both with and without an onium-type photoacid generator (PAG). With increasing PHS concentration, the rate constant of deprotonation of PHS radical cations was found to decrease. In the presence of PAG, the yield of the multimer radical cation of PHS was shown to decrease. We found that pairing between the anions produced by the attachment of dissociative electrons of PAGs and the monomer PHS radical cations restrict local molecular motions, leading to the formation of the multimer PHS radical cations.

  3. X-ray, spectroscopic and semiempirical investigation of the structure of lasalocid 6-bromohexyl ester and its complexes with alkali metal cations

    NASA Astrophysics Data System (ADS)

    Huczyński, Adam; Ratajczak-Sitarz, Małgorzata; Katrusiak, Andrzej; Brzezinski, Bogumil

    2011-07-01

    The ionophoric antibiotic lasalocid acid has been converted to a novel 6-bromohexyl ester (LASBR) and its structure has been determined in the crystal by X-ray diffraction and in solution by NMR and FT-IR methods. In the crystal two symmetry-independent LASBR molecules are present. The structure of LASBR in solution is slightly different because the strongest intramolecular C(1) dbnd O⋯H sbnd (3)O hydrogen bond in the pseudo-aromatic ring becomes partially broken and a new hydrogen bond between O(4)H and carbonyl group C(13) dbnd O is formed. LASBR forms complexes with Li +, Na + and K + cations of exclusively 1:1 stoichiometry. The structures of complexes have been studied and visualized using semi-empirical calculation based on results of spectrometric and spectroscopic investigation. It is demonstrated that in contrast to lasalocid acid the novel ester forms preferential complexes with Li + cation.

  4. Alkali metal ionization detector

    DOEpatents

    Bauerle, James E.; Reed, William H.; Berkey, Edgar

    1978-01-01

    Variations in the conventional filament and collector electrodes of an alkali metal ionization detector, including the substitution of helical electrode configurations for either the conventional wire filament or flat plate collector; or, the substitution of a plurality of discrete filament electrodes providing an in situ capability for transferring from an operationally defective filament electrode to a previously unused filament electrode without removing the alkali metal ionization detector from the monitored environment. In particular, the helical collector arrangement which is coaxially disposed about the filament electrode, i.e. the thermal ionizer, provides an improved collection of positive ions developed by the filament electrode. The helical filament design, on the other hand, provides the advantage of an increased surface area for ionization of alkali metal-bearing species in a monitored gas environment as well as providing a relatively strong electric field for collecting the ions at the collector electrode about which the helical filament electrode is coaxially positioned. Alternatively, both the filament and collector electrodes can be helical. Furthermore, the operation of the conventional alkali metal ionization detector as a leak detector can be simplified as to cost and complexity, by operating the detector at a reduced collector potential while maintaining the sensitivity of the alkali metal ionization detector adequate for the relatively low concentration of alkali vapor and aerosol typically encountered in leak detection applications.

  5. Intrinsic affinities of alkali cations for 15-crown-5 and 18-crown-6: Bond dissociation energies of gas-phase M{sup +}-crown ether complexes

    SciTech Connect

    More, M.B.; Ray, D.; Armentrout, P.B.

    1999-01-20

    Bond dissociation energies (BDEs) of M{sup +}[c-(C{sub 2}H{sub 4}O){sub 5}] and M{sup +}[c-(C{sub 2}H{sub 4}O){sub 6}] for M = Na, K, Rb, and Cs are reported. The BDEs are determined experimentally by analysis of the thresholds for collision-induced dissociation of the cation-crown ether complexes by xenon measured by using guided ion beam mass spectrometry. In all cases, the primary and lowest energy dissociation channel observed experimentally in endothermic loss of the ligand molecule. The cross section thresholds are interpreted to yield 0 and 298 K BDEs after accounting for the effects of multiple ion-molecule collisions, internal energy of the complexes, and unimolecular decay rates. For both 18-crown-6 and 15-crown-5, the BDEs decrease monotonically with increasing cation size. These results indicate that the intrinsic affinity of c-(C{sub 2}H{sub 4}O){sub 5} and c-(C{sub 2}H{sub 4}O){sub 6} for M{sup +} is determined principally by the charge density of the cation not by the ratio of the ionic radius to the cavity size. The BDEs reported here are in fair agreement with recent ab initio calculations at the MP2 level with 6-31+G* basis sets. The experimental values are systematically smaller than the computed values by 8 {+-} 2 kJ/mol per metal-oxygen interaction. The existence of less strongly bound isomers in the experimental apparatus for Rb{sup +}(15-crown-5) and Cs{sup +}(15-crown-5) appears likely, but their absence for Na{sup +} and K{sup +} complexes indicates interesting metal-dependent dynamics to the formation of such isomers.

  6. Ground-state properties of alkali dimers and their cations (including the elements Li, Na, and K) from ab initio calculations with effective core polarization potentials

    NASA Astrophysics Data System (ADS)

    Müller, Wolfgang; Meyer, Wilfried

    1984-04-01

    Extensive all-electron SCF and valence CI calculations are presented for alkali dimer systems with consideration of intershell correlation effects by use of an effective core polarization potential (CPP), which contains only a single adjustable atomic parameter. High accuracy is obtained for the ground-state spectroscopic constants of the studied molecules. The maximum deviations from accurate experimental data are as follows: 1% or 0.03 Å for Re, 2% or 100 cm-1 for De, 0.5% or 1 cm-1 for ωe, and 0.2% or 100 cm-1 for ionization energies. For experimentally uncertain or unknown values reliable predictions can thus be made. The calculated dipole moments for LiK and NaK agree with experiment to within 0.1%, but for LiNa we obtain a deviation of 8% or 0.036 D. An analysis of molecular core polarization contributions reveals the reasons for some systematic defects in previous pseudopotential calculations.

  7. Carboxylate Ion Pairing with Alkali-Metal Ions for β-Lactoglobulin and Its Role on Aggregation and Interfacial Adsorption.

    PubMed

    Beierlein, Frank R; Clark, Timothy; Braunschweig, Björn; Engelhardt, Kathrin; Glas, Lena; Peukert, Wolfgang

    2015-04-30

    We report a combined experimental and computational study of the whey protein β-lactoglobulin (BLG) in different electrolyte solutions. Vibrational sum-frequency generation (SFG) and ellipsometry were used to investigate the molecular structure of BLG modified air-water interfaces as a function of LiCl, NaCl, and KCl concentrations. Molecular dynamics (MD) simulations and thermodynamic integration provided details of the ion pairing of protein surface residues with alkali-metal cations. Our results at pH 6.2 indicate that BLG at the air-water interface forms mono- and bilayers preferably at low and high ionic strength, respectively. Results from SFG spectroscopy and ellipsometry are consistent with intimate ion pairing of alkali-metal cations with aspartate and glutamate carboxylates, which is shown to be more effective for smaller cations (Li(+) and Na(+)). MD simulations show not only carboxylate-alkali-metal ion pairs but also ion multiplets with the alkali-metal ion in a bridging position between two or more carboxylates. Consequently, alkali-metal cations can bridge carboxylates not only within a monomer but also between monomers, thus providing an important dimerization mechanism between hydrophilic surface patches. PMID:25825918

  8. Generation of alkali-free and high-proton concentration layer in a soda lime glass using non-contact corona discharge

    SciTech Connect

    Ikeda, Hiroshi; Sakai, Daisuke; Nishii, Junji; Funatsu, Shiro; Yamamoto, Kiyoshi; Suzuki, Toshio; Harada, Kenji

    2013-08-14

    Formation mechanisms of alkali-free and high-proton concentration surfaces were investigated for a soda lime glass using a corona discharge treatment under an atmospheric pressure. Protons produced by high DC voltage around an anode needle electrode were incorporated into a sodium ion site in the anode side glass. The sodium ion was swept away to the cathode side as a charge carrier. Then it was discharged. The precipitated sodium was transformed to a Na{sub 2}CO{sub 3} powder when the surface contacted with air. The sodium ion in the glass surface layer of the anode side was replaced completely by protons. The concentration of OH groups in the layer was balanced with the amount of excluded sodium ions. The substitution reaction of sodium ions with protons tends to be saturated according to a square root function of time. The alkali depletion layer formation rate was affected by the large difference in mobility between sodium ions and protons in the glass.

  9. Salts of alkali metal anions and process of preparing same

    DOEpatents

    Dye, James L.; Ceraso, Joseph M.; Tehan, Frederick J.; Lok, Mei Tak

    1978-01-01

    Compounds of alkali metal anion salts of alkali metal cations in bicyclic polyoxadiamines are disclosed. The salts are prepared by contacting an excess of alkali metal with an alkali metal dissolving solution consisting of a bicyclic polyoxadiamine in a suitable solvent, and recovered by precipitation. The salts have a gold-color crystalline appearance and are stable in a vacuum at -10.degree. C. and below.

  10. Dynamic chiral-at-metal stability of tetrakis(d/l-hfc)Ln(III) complexes capped with an alkali metal cation in solution.

    PubMed

    Lin, Yiji; Zou, Fang; Wan, Shigang; Ouyang, Jie; Lin, Lirong; Zhang, Hui

    2012-06-14

    Chiral tetrakis(β-diketonate) Ln(III) complexes Δ-[NaLa(d-hfc)(4)(CH(3)CN)] (1) and Λ-[NaLa(l-hfc)(4) (CH(3)CN)] (2) (d/l-hfc(-) = 3-heptafluo-robutylryl-(+)/(-)-camphorate) are a pair of enantiomers and crystallize in the same Sohncke space group (P2(1)2(1)2(1)) with dodecahedral (DD) geometry. Typically positive and negative exciton splitting patterns around 320 nm were observed in the solid-state circular dichroism (CD) spectra of complexes 1 and 2, which indicate that their shell configurational chiralities are Δ and Λ, respectively. The apparent bisignate couplets in the solid-state CD spectra of [CsLn(d-hfc)(4)(H(2)O)] [Ln = La (3), Yb (5)] and [CsLn(l-hfc)(4)(H(2)O)] [Ln = La (4), Yb (6)] show that they are a pair of enantiomers and their absolute configurations are denoted Δ and Λ, respectively. The crystallographic data of 5 reveals that its coordination polyhedron is the square antiprism (SAP) geometry and it undergoes a phase transition from triclinic (α phase, P1) to monoclinic (β phase, C2) upon cooling. The difference between the two phases is brought about by the temperature dependent behaviour of the coordination water molecules, but this did not affect the configurational chirality of the Δ-SAP-[Yb(d-hfc)(4)](-) moiety. Furthermore, time-dependent CD, UV-vis and (19)F NMR were applied to study the solution behavior of these complexes. It was found that the chiral-at-metal stability of the three pairs of complexes is different and affected by both the Ln(3+) and M(+) ion size. The results show that the Cs(+) cation can retain the metal center chirality and stablize the structures of [Ln(d/l-hfc)(4)](-) or the dissociated tris(d/l-hfc)Ln(III) species in solution for a longer time than that of the Na(+) cation, and it is important that the Cs(+) ion successfully lock the configurational chirality around the Yb(3+) center of the complex species in solution. This is reasoned by the short Cs(+)···FC, Cs(+)···O-Yb and Cs(+)···Yb(3

  11. Monitoring nasal allergic inflammation by measuring the concentration of eosinophil cationic protein and eosinophils in nasal secretions.

    PubMed

    Wang, D; Clement, P; Smitz, J; de Waele, M; Derde, M P

    1995-02-01

    Quantitative measurement of the eosinophil cationic protein (ECP) concentration and the percentage of eosinophils in nasal secretions has greatly improved our understanding of the inflammatory process after natural allergen exposure. ECP and eosinophils were measured in the nasal secretions of 40 symptomatic patients with seasonal allergic rhinitis during the pollen season. Results showed a significant relationship between a high concentration of ECP (median: 410 ng/g, range: 6-2380 ng/g) and a high percentage of eosinophils (median: 13.5%, range: 1-85%). This quantitative study again demonstrated that infiltration by eosinophils and release of ECP play a key role in allergic rhinitis. It also suggests that the combined measurement of the percentage of eosinophils together with the ECP concentration in nasal secretions seems to be a very useful model in monitoring and assessing the condition of chronic nasal inflammation in patients with allergic rhinitis. PMID:7604937

  12. 10 000-fold concentration increase of the biomarker cardiac troponin I in a reducing union microfluidic chip using cationic isotachophoresis†

    PubMed Central

    Bottenus, Danny; Jubery, Talukder Zaki; Ouyang, Yexin; Dong, Wen-Ji; Dutta, Prashanta

    2011-01-01

    This paper describes the preconcentration of the biomarker cardiac troponin I (cTnI) and a fluorescent protein (R-phycoerythrin) using cationic isotachophoresis (ITP) in a 3.9 cm long poly(methyl methacrylate) (PMMA) microfluidic chip. The microfluidic chip includes a channel with a 5× reduction in depth and a 10× reduction in width. Thus, the overall cross-sectional area decreases by 50× from inlet (anode) to outlet (cathode). The concentration is inversely proportional to the cross-sectional area so that as proteins migrate through the reductions, the concentrations increase proportionally. In addition, the proteins gain additional concentration by ITP. We observe that by performing ITP in a cross-sectional area reducing microfluidic chip we can attain concentration factors greater than 10 000. The starting concentration of cTnI was 2.3 μg mL–1 and the final concentration after ITP concentration in the microfluidic chip was 25.52 ± 1.25 mg mL–1. To the author's knowledge this is the first attempt at concentrating the cardiac biomarker cTnI by ITP. This experimental approach could be coupled to an immunoassay based technique and has the potential to lower limits of detection, increase sensitivity, and quantify different isolated cTnI phosphorylation states. PMID:21308695

  13. 10 000-fold concentration increase of the biomarker cardiac troponin I in a reducing union microfluidic chip using cationic isotachophoresis†

    PubMed Central

    Bottenus, Danny; Jubery, Talukder Zaki; Ouyang, Yexin; Dong, Wen-Ji; Dutta, Prashanta

    2012-01-01

    This paper describes the preconcentration of the biomarker cardiac troponin I (cTnI) and a fluorescent protein (R-phycoerythrin) using cationic isotachophoresis (ITP) in a 3.9 cm long poly(methyl methacrylate) (PMMA) microfluidic chip. The microfluidic chip includes a channel with a 5× reduction in depth and a 10× reduction in width. Thus, the overall cross-sectional area decreases by 50× from inlet (anode) to outlet (cathode). The concentration is inversely proportional to the cross-sectional area so that as proteins migrate through the reductions, the concentrations increase proportionally. In addition, the proteins gain additional concentration by ITP. We observe that by performing ITP in a cross-sectional area reducing microfluidic chip we can attain concentration factors greater than 10 000. The starting concentration of cTnI was 2.3 μg mL−1 and the final concentration after ITP concentration in the microfluidic chip was 25.52 ± 1.25 mg mL−1. To the author’s knowledge this is the first attempt at concentrating the cardiac biomarker cTnI by ITP. This experimental approach could be coupled to an immunoassay based technique and has the potential to lower limits of detection, increase sensitivity, and quantify different isolated cTnI phosphorylation states. PMID:21416810

  14. Effect of alkali cations on two-dimensional networks of two new quaternary thioarsenates (III) prepared by a facile surfactant-thermal method

    NASA Astrophysics Data System (ADS)

    Yan, Dongming; Hou, Peipei; Liu, Chang; Chai, Wenxiang; Zheng, Xuerong; Zhang, Luodong; Zhi, Mingjia; Zhou, Chunmei; Liu, Yi

    2016-09-01

    Two new quaternary thioarsenates(III) NaAg2AsS3·H2O (1) and KAg2AsS3 (2) with high yields have been successfully prepared through a facile surfactant-thermal method. It is interesting that 2 can only be obtained with the aid of ethanediamine (en), which indicates that weak basicity of solvent is beneficial to the growth of 2 compared with 1. Both 1 and 2 feature the similar two-dimensional (2D) layer structures. However, the distortion of the primary honeycomb-like nets in 2 is more severe than that of 1, which demonstrates that Na+ and K+ cations have different structure directing effects on these two thioarsenates(III). Both experimental and theoretical studies confirm 1 and 2 are semiconductors with band gaps in the visible region. Our success in preparing these two quaternary thioarsenates(III) proves that surfactant-thermal technique is a powerful yet facile synthetic method to explore new complex chalcogenides.

  15. Acute toxicity of the cationic surfactant C12-benzalkonium in different bioassays: how test design affects bioavailability and effect concentrations.

    PubMed

    Chen, Yi; Geurts, Marc; Sjollema, Sascha B; Kramer, Nynke I; Hermens, Joop L M; Droge, Steven T J

    2014-03-01

    Using an ion-exchange-based solid-phase microextraction (SPME) method, the freely dissolved concentrations of C12-benzalkonium were measured in different toxicity assays, including 1) immobilization of Daphnia magna in the presence or absence of dissolved humic acid; 2) mortality of Lumbriculus variegatus in the presence or absence of a suspension of Organisation for Economic Co-Operation and Development (OECD) sediment; 3) photosystem II inhibition of green algae Chlorella vulgaris; and 4) viability of in vitro rainbow trout gill cell line (RTgill-W1) in the presence or absence of serum proteins. Furthermore, the loss from chemical adsorption to the different test vessels used in these tests was also determined. The C12-benzalkonium sorption isotherms to the different sorbent phases were established as well. Our results show that the freely dissolved concentration is a better indicator of the actual exposure concentration than the nominal or total concentration in most test assays. Daphnia was the most sensitive species to C12-benzalkonium. The acute Daphnia and Lumbriculus tests both showed no enhanced toxicity from possible ingestion of sorbed C12-benzalkonium in comparison with water-only exposure, which is in accordance with the equilibrium partitioning theory. Moreover, the present study demonstrates that commonly used sorbent phases can strongly affect bioavailability and observed effect concentrations for C12-benzalkonium. Even stronger effects of decreased actual exposure concentrations resulting from sorption to test vessels, cells, and sorbent phases can be expected for more hydrophobic cationic surfactants. PMID:24273010

  16. Alkali Bee

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The alkali bee, Nomia melanderi, is native to deserts and semi-arid desert basins of the western United States. It is a very effective and manageable pollinator for the production of seed in alfalfa (=lucerne) and some other crops, such as onion. It is the world’s only intensively managed ground-n...

  17. LA-ICP-MS of rare earth elements concentrated in cation-exchange resin particles for origin attribution of uranium ore concentrate.

    PubMed

    Asai, Shiho; Limbeck, Andreas

    2015-04-01

    Rare earth elements (REE) concentrated on cation-exchange resin particles were measured with laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) to obtain chondrite-normalized REE plots. The sensitivity of REE increased in ascending order of the atomic number, according to the sensitivity trend in pneumatic nebulization ICP-MS (PN-ICP-MS). The signal intensities of REE were nearly proportional to the concentrations of REE in the immersion solution used for particle-preparation. Minimum measurable concentration calculated from the net signals of REE was approximately 1 ng/g corresponding to 0.1 ng in the particle-preparation solution. In LA analysis, formation of oxide and hydroxide of the light REE and Ba which causes spectral interferences in the heavy REE measurement was effectively attenuated due to the solvent-free measurement capability, compared to conventional PN-ICP-MS. To evaluate the applicability of the proposed method, the REE-adsorbed particles prepared by immersing them in a U-bearing solution (commercially available U standard solution) were measured with LA-ICP-MS. Aside from the LA analysis, each concentration of REE in the same U standard solution was determined with conventional PN-ICP-MS after separating REE by cation-exchange chromatography. The concentrations of REE were ranging from 0.04 (Pr) to 1.08 (Dy) μg/g-U. The chondrite-normalized plot obtained through LA-ICP-MS analysis of the U standard sample exhibited close agreement with that obtained through the PN-ICP-MS of the REE-separated solution within the uncertainties. PMID:25640124

  18. Purification of alkali metal nitrates

    DOEpatents

    Fiorucci, Louis C.; Gregory, Kevin M.

    1985-05-14

    A process is disclosed for removing heavy metal contaminants from impure alkali metal nitrates containing them. The process comprises mixing the impure nitrates with sufficient water to form a concentrated aqueous solution of the impure nitrates, adjusting the pH of the resulting solution to within the range of between about 2 and about 7, adding sufficient reducing agent to react with heavy metal contaminants within said solution, adjusting the pH of the solution containing reducing agent to effect precipitation of heavy metal impurities and separating the solid impurities from the resulting purified aqueous solution of alkali metal nitrates. The resulting purified solution of alkali metal nitrates may be heated to evaporate water therefrom to produce purified molten alkali metal nitrate suitable for use as a heat transfer medium. If desired, the purified molten form may be granulated and cooled to form discrete solid particles of alkali metal nitrates.

  19. The alkali metals: 200 years of surprises.

    PubMed

    Dye, James L

    2015-03-13

    Alkali metal compounds have been known since antiquity. In 1807, Sir Humphry Davy surprised everyone by electrolytically preparing (and naming) potassium and sodium metals. In 1808, he noted their interaction with ammonia, which, 100 years later, was attributed to solvated electrons. After 1960, pulse radiolysis of nearly any solvent produced solvated electrons, which became one of the most studied species in chemistry. In 1968, alkali metal solutions in amines and ethers were shown to contain alkali metal anions in addition to solvated electrons. The advent of crown ethers and cryptands as complexants for alkali cations greatly enhanced alkali metal solubilities. This permitted us to prepare a crystalline salt of Na(-) in 1974, followed by 30 other alkalides with Na(-), K(-), Rb(-) and Cs(-) anions. This firmly established the -1 oxidation state of alkali metals. The synthesis of alkalides led to the crystallization of electrides, with trapped electrons as the anions. Electrides have a variety of electronic and magnetic properties, depending on the geometries and connectivities of the trapping sites. In 2009, the final surprise was the experimental demonstration that alkali metals under high pressure lose their metallic character as the electrons are localized in voids between the alkali cations to become high-pressure electrides! PMID:25666067

  20. Adsorption on Alkali Halides.

    NASA Astrophysics Data System (ADS)

    Urzua Duran, Gilberto Antonio

    1995-01-01

    Using a variety of interionic potentials, I have computed the configurations of adsorbed alkali halides monomers on the (001) surface of selected alkali halides crystals. In the majority of cases studied it is found that the monomer adsorbs perpendicular to the surface with the cation sitting nearly on top of the surface anion. In about ten percent of the cases though the monomer adsorbs tilted from the vertical. In these cases the ion that is closer to the surface can be the cation or the anion. The effect of polarization forces is found to be important. In order to discuss the effects of surface retaxation with adsorbates, I have evaluated the surface relaxation of the alkali halide crystals, using a shell model for the interionic forces. It is found that surface relaxation and rumpling are generally small, especially when the van der Waals forces are included. A theory of the effect of substrate vibrations on the binding of an adsorbed atom is developed. At T = 0 the binding energy is D_0-E, where D_0 is the surface well depth (classical binding energy) and E is the quantum correction. For several simple models, it is found that E is surprisingly model-independent. We compare D _0-E with the binding energies to a rigid substrate, D_0-E_{rs}, and to a vibrationally averaged substrate, D _0-E_{va}. We prove that E_{va}>=q E>=q E_ {rs} and that similar relations hold at finite temperature for the free energy of binding. In most cases E_{rs} is better than E_{va} as an approximation to E.

  1. Predicting timothy mineral concentrations, dietary cation-anion difference, and grass tetany index by near-infrared reflectance spectroscopy.

    PubMed

    Tremblay, G F; Nie, Z; Bélanger, G; Pelletier, S; Allard, G

    2009-09-01

    The mineral concentration of forage grasses plays a significant role in 2 metabolic disorders in dairy cattle production, namely, hypocalcemia (milk fever) and hypomagnesemia (grass tetany). Risks of occurrence of these 2 metabolic disorders can be evaluated by determining the dietary cation-anion difference (DCAD) and the grass tetany (GT) index of forages and specific rations. The objective of this study was to evaluate the feasibility of predicting timothy (Phleum pratense L.) mineral concentrations of Na, K, Ca, Mg, Cl, S, and P, the DCAD, and the GT index by near-infrared reflectance spectroscopy (NIRS). Timothy samples (n = 1,108) were scanned using NIRS and analyzed for the concentration of 7 mineral elements. Calculations of the DCAD were made using 3 different formulas, and the GT index was also calculated. Samples were divided into calibration (n = 240) and validation (n = 868) sets. The calibration, cross-validation, and prediction for mineral concentrations, the DCAD, and the GT index were performed using modified partial least squares regression. Concentrations of K, Ca, Mg, Cl, and P were successfully predicted with coefficients of determination of prediction (R(P)2) of 0.69 to 0.92 and coefficients of variation of prediction (CV(P)) ranging from 6.6 to 11.4%. The prediction of Na and S concentrations failed, with respective R(P)2 of 0.58 and 0.53 and CV(P) of 82.2 and 12.9%. The 3 calculated DCAD and the GT index were predicted successfully, with R(P)2 >0.90 and CV(P) <20%. Our results confirm the feasibility of using NIRS to predict K, Ca, Mg, and Cl concentrations, as well as the DCAD and the GT index, in timothy. PMID:19700711

  2. Maleic acid-styrene encapsulated silica cation exchanger in high performance liquid chromatography.

    PubMed

    Yang, R; Jiang, S; Chen, L

    2001-12-24

    The use of poly(maleic acid-styrene)-encapsulated silica for the determination of monovalent and divalent cations is well accepted in ion chromatography. The separation of Mn(2+), alkali and alkaline earth metal cations is obtained under the same chromatographic conditions. The influences of pH and the concentration of eluent on the retention of cations have been studied. The preparation conditions of packings were studied. The metal ions in the boiler water samples from a thermal power plant were quantitatively determined using this column. The results are in agreement with those determined by ICP and Volumetric analysis methods. PMID:18968461

  3. Membrane potential difference and intracellular cation concentrations in human placental trophoblast cells in culture.

    PubMed Central

    Greenwood, S L; Clarson, L H; Sides, M K; Sibley, C P

    1996-01-01

    1. The electrochemical gradients for Na+ and K+ were assessed in a cell culture model of trophoblast differentiation. 2. Membrane potential difference (Em), intracellular water and Na+ and K+ contents were measured in choriocarcinoma cells (JAr cell line; 96% of which are undifferentiated trophoblast cells) and in mononucleate and multinucleate (differentiated) cytotrophoblast cells isolated from the human placenta at term. 3. There was a significant fall in Em from -57 mV in JAr cells, to -48 and -40 mV in mono-and multinucleate cytotrophoblast cells, respectively. Treatment with ouabain (1 mM for 15 min) depolarized the JAr cell membrane by 15 mV but did not affect cytotrophoblast cell membrane potential. 4. Intracellular K+ concentration was similar in JAr, mono- and multinucleate cytotrophoblast cells but Na+ concentration was higher in mononucleate cytotrophoblast cells compared with JAr cells. 5. Ouabain treatment (3 mM for 15 min) caused a small increase (4.5%) in cell water in mononucleate cytotrophoblast cells but lowered K+ (approximately 30%) and increased Na+ concentration (approximately 125%) in all the trophoblast cells studied. 6. The K+ equilibrium potential (EK) was more negative than Em in all cells and the difference between EK and Em was smaller in JAr cells (-25 mV) than in mono- and multinucleate cytotrophoblast cells (-33 and -43 mV, respectively). 7. The Na+ equilibrium potential (ENa) was positive in the trophoblast cells and the difference between ENa and Em was 122, 100 and 100 mV in JAr, mono- and multinucleate cytotrophoblast cells, respectively. 8. These results suggest that the electrochemical gradient for K+ is affected by the stage of trophoblast cell differentiation. In contrast, the electrochemical gradient for Na+ is similar in mono- and multinucleate cytotrophoblast cells. Images Figure 1 PMID:8734977

  4. Comparison of Reactive Mercury Concentrations Measured Simultaneously Using KCl-coated Denuders, Nylon Membranes, and Cation Exchange Membranes

    NASA Astrophysics Data System (ADS)

    Gustin, M. S.; Huang, J.; Miller, M. B.; Weiss-Penzias, P. S.

    2012-12-01

    There is much debate about the chemistry of reactive gaseous and particle bound mercury (Hg) in the atmosphere, and the processes associated with formation. In addition, there are concerns regarding the interferences and calibration of the widely used Tekran® 2537/1130/1135 Hg measurement system. To investigate these we developed simple laboratory and field sampling systems designed to collect and analyze reactive Hg (Hg (II), Hg (I) and/or particle bound). A manifold system was applied in the laboratory, and in the field, in-series and -parallel membranes, flow controllers and pumps were utilized. Both systems actively collected reactive Hg using nylon membranes and cation exchange membranes alongside measurements made using the Tekran® system. The analytical system consisted of step wise 2.5 minute thermo-desorption and Hg quantification by cold vapor atomic fluorescence. In the laboratory, we compared the efficiency of these surfaces for collection of HgO, HgCl2, and HgBr2 when permeated into Hg and oxidant free air, and ambient filtered air. Other tests are ongoing. Thus far, results show concentrations measured by the cation exchange membrane were two-to-three fold greater than that measured by the nylon membranes, and three-to -four fold greater than that measured by the KCl-coated annual denuder. Thermo-desorption profiles obtained using nylon membranes show slightly different patterns associated with the reactive Hg compounds as permeated and tested. Field measurements were made at two locations in Reno, Nevada (a high traffic site and an agricultural area) and at Elkhorn Slough, California (marine site). Desorption profiles from nylon membrane differed by site and by time of year. Although the influence of aerosol on this measurement has not been explored, field results suggest different forms of reactive Hg were present in the atmosphere as a function of season and location.

  5. On the time behaviour of the concentration of pyrazinium radical cations in the early stage of the Maillard reaction

    NASA Astrophysics Data System (ADS)

    Stoesser, Reinhard; Klein, Jeannette; Peschke, Simone; Zehl, Andrea; Cämmerer, Bettina; Kroh, Lothar W.

    2007-08-01

    During the early stage of the Maillard reaction pyrazinium radical cations were detected by ESR within the reaction system D-glucose/glycine. The spectra were characterized by completely resolved hyperfine structure. The partial pressure of oxygen and the radical concentrations were measured directly in the reaction mixture by ESR using solutions of the spin probe TEMPOL and of DPPH, respectively. There are quantitative and qualitative relations of the actual concentration of the radical ions to the partial pressure of oxygen, the temperature-time regime and the mechanical mixing of the reaction system. These macroscopic parameters significantly affect both the induction period and the velocity of the time-dependent formation of free radicals. From in situ variations of p(O 2) and p(Ar) including the connected mixing effects caused by the passing the gases through the reaction mixture, steric and chemical effects of the stabilization of the radical ions were established. The determination of suitable and relevant conditions for stabilization and subsequent radical reactions contributes to the elucidation of the macroscopically known antioxidant activity of Maillard products.

  6. Effect of temperature and CO 2 concentration on laser-induced breakdown spectroscopy measurements of alkali fume

    NASA Astrophysics Data System (ADS)

    Molina, Alejandro; Shaddix, Christopher R.; Sickafoose, Shane M.; Walsh, Peter M.; Blevins, Linda G.

    2005-08-01

    Laser-induced breakdown spectroscopy (LIBS) was used in the evaluation of aerosol concentration in the exhaust of an oxygen/natural-gas glass furnace. Experiments showed that for a delay time of 10 μs and a gate width of 50 μs, the presence of CO 2 and changes in gas temperature affect the intensity of both continuum emission and the Na D lines. The intensity increased for the neutral Ca and Mg lines in the presence of 21% CO 2 when compared to 100% N 2, whereas the intensity of the Mg and Ca ionic lines decreased. An increase in temperature from 300 to 730 K produced an increase in both continuum emission and Na signal. These laboratory measurements were consistent with measurements in the glass furnace exhaust. Time-resolved analysis of the spark radiation suggested that differences in continuum radiation resulting from changes in bath composition are only apparent at long delay times. The changes in the intensity of ionic and neutral lines in the presence of CO 2 are believed to result from higher free electron number density caused by lower ionization energies of species formed during the spark decay process in the presence of CO 2. For the high Na concentration observed in the glass furnace exhaust, self-absorption of the spark radiation occurred. Power law regression was used to fit laboratory Na LIBS calibration data for sodium loadings, gas temperatures, and a CO 2 content representative of the furnace exhaust. Improvement of the LIBS measurement in this environment may be possible by evaluation of Na lines with weaker emission and through the use of shorter gate delay times.

  7. Adaptation of Escherichia coli to elevated sodium concentrations increases cation tolerance and enables greater lactic acid production.

    PubMed

    Wu, Xianghao; Altman, Ronni; Eiteman, Mark A; Altman, Elliot

    2014-05-01

    Adaptive evolution was employed to generate sodium (Na(+))-tolerant mutants of Escherichia coli MG1655. Four mutants with elevated sodium tolerance, designated ALS1184, ALS1185, ALS1186, and ALS1187, were independently isolated after 73 days of serial transfer in medium containing progressively greater Na(+) concentrations. The isolates also showed increased tolerance of K(+), although this cation was not used for selective pressure. None of the adapted mutants showed increased tolerance to the nonionic osmolyte sucrose. Several physiological parameters of E. coli MG1655 and ALS1187, the isolate with the greatest Na(+) tolerance, were calculated and compared using glucose-limited chemostats. Genome sequencing showed that the ALS1187 isolate contained mutations in five genes, emrR, hfq, kil, rpsG, and sspA, all of which could potentially affect the ability of E. coli to tolerate Na(+). Two of these genes, hfq and sspA, are known to be involved in global regulatory processes that help cells endure a variety of cellular stresses. Pyruvate formate lyase knockouts were constructed in strains MG1655 and ALS1187 to determine whether increased Na(+) tolerance afforded increased anaerobic generation of lactate. In fed-batch fermentations, E. coli ALS1187 pflB generated 76.2 g/liter lactate compared to MG1655 pflB, which generated only 56.3 g/liter lactate. PMID:24584246

  8. Deterministic Role of Concentration Surplus of Cation Vacancy over Anion Vacancy in Bipolar Memristive NiO.

    PubMed

    Sun, Zhong; Zhao, Yonggang; He, Min; Gu, Lin; Ma, Chao; Jin, Kuijuan; Zhao, Diyang; Luo, Nannan; Zhang, Qinghua; Wang, Na; Duan, Wenhui; Nan, Ce-Wen

    2016-05-11

    Migration of oxygen vacancies has been proposed to play an important role in the bipolar memristive behaviors because oxygen vacancies can directly determine the local conductivity in many systems. However, a recent theoretical work demonstrated that both migration of oxygen vacancies and coexistence of cation and anion vacancies are crucial to the occurrence of bipolar memristive switching, normally observed in the small-sized NiO. So far, experimental work addressing this issue is still lacking. In this work, with conductive atomic force microscopy and combined scanning transmission electron microscopy and electron energy loss spectroscopy, we reveal that concentration surplus of Ni vacancy over O vacancy determines the bipolar memristive switching of NiO films. Our work supports the dual-defects-based model, which is of fundamental importance for understanding the memristor mechanisms beyond the well-established oxygen-vacancy-based model. Moreover, this work provides a methodology to investigate the effect of dual defects on memristive behaviors. PMID:27096884

  9. Seasonal evolution of anionic, cationic and non-ionic surfactant concentrations in coastal aerosols from Askö, Sweden

    NASA Astrophysics Data System (ADS)

    Gérard, Violaine; Nozière, Barbara; Baduel, Christine

    2015-04-01

    Surfactants present in atmospheric aerosols are expected to enhance the activation into cloud droplets by acting on one of the two key parameters of the Köhler equation: the surface tension, σ. But because the magnitude of this effect and its regional and temporal variability are still highly uncertain [1,2], various approaches have been developed to evidence it directly in the atmosphere. This work presents the analysis of surfactants present in PM2.5 aerosol fractions collected at the coastal site of Askö, Sweden (58° 49.5' N, 17° 39' E) from July to October 2010. The total surfactant fraction was extracted from the samples using an improved double extraction technique. Surface tension measurements performed with the pendant drop technique [3] indicated the presence of very strong surfactants (σ ~ 30 - 35 mN/m) in these aerosols. In addition, these extractions were combined with colorimetric methods to determine the anionic, cationic and non-ionic surfactant concentrations [4,5], and provided for the first time interference-free surfactant concentrations in atmospheric aerosols. At this site, the total surfactant concentration in the PM2.5 samples varied between 7 to 150 mM and was dominated by anionic and non-ionic ones. The absolute surface tension curves obtained for total surfactant fraction displayed Critical Micelle Concentrations (CMC) in the range 50 - 400 uM, strongly suggesting a biological origin for the surfactants. The seasonal evolution of these concentrations and their relationships with environmental or meteorological parameters at the site will be discussed. [1] Ekström, S., Nozière, B. et al., Biogeosciences, 2010, 7, 387 [2] Baduel, C., Nozière, B., Jaffrezo, J.-L., Atmos. Environ., 2012, 47, 413 [3] Nozière, B., Baduel, C., Jaffrezo, J.-L., Nat. Commun., 2014, 5, 1 [4] Latif, M. T.; Brimblecombe, P. Environ. Sci. Technol., 2004, 38, 6501 [5] Pacheco e Silva et al., Method to measure surfactant in fluid, 2013, US 2013/0337568 A1

  10. Regenerable activated bauxite adsorbent alkali monitor probe

    DOEpatents

    Lee, Sheldon H. D.

    1992-01-01

    A regenerable activated bauxite adsorber alkali monitor probe for field applications to provide reliable measurement of alkali-vapor concentration in combustion gas with special emphasis on pressurized fluidized-bed combustion (PFBC) off-gas. More particularly, the invention relates to the development of a easily regenerable bauxite adsorbent for use in a method to accurately determine the alkali-vapor content of PFBC exhaust gases.

  11. Regenerable activated bauxite adsorbent alkali monitor probe

    DOEpatents

    Lee, S.H.D.

    1992-12-22

    A regenerable activated bauxite adsorber alkali monitor probe for field applications to provide reliable measurement of alkali-vapor concentration in combustion gas with special emphasis on pressurized fluidized-bed combustion (PFBC) off-gas. More particularly, the invention relates to the development of a easily regenerable bauxite adsorbent for use in a method to accurately determine the alkali-vapor content of PFBC exhaust gases. 6 figs.

  12. Acid and alkali doped PBI electrolyte in electrochemical system

    NASA Astrophysics Data System (ADS)

    Xing, Baozhong

    In this work the conductivity of blank PBI membrane, acid doped PBI and alkaline doped PBI was systematically studied. A new methodology for sorption kinetics study in electrolyte solution has been established by monitoring the conductivity change during the sorption process. The model of the doping process and mechanism of conductivity are proposed. The performance of PBI (doped under optimum conditions) in fuel cell as PEM was evaluated. The experimental results show that the blank PBI in acid solution is an ionic insulator. It clarified the long time confusion in this area. The acid doped PBI membrane is an ionic conductor. The conductivity increases with the concentration of the acid solution. In high concentration acid solution, the conductivity increases with the type of acid in the order: H2SO 4 > H3PO4 > HClO4 > HNO3 > HCl. The kinetics of the doping process was studied, by a continuous method. The ionic conductivity mechanism was established. The PBI membranes doped with H2SO4 and H3PO4 exhibit better performance than NafionRTM. The doped FBI has more resistance to CO poison. 3% CO in H2 has little effect on the H3PO 4 doped PBI membrane at 185°C. The conductivity of the alkali doped PBI membrane changes with the concentration of the alkaline solution and the type of the alkalis. The conductivity has a maximum in KOH and NaOH solution. The maximum conductivity in KOH is higher than in NaOH and LiOH. It is about 5 times of that of NafionRTM in alkaline solution. The two-step sorption process in alkaline solution was observed. The first step is the permeation process of the alkalis in the PBI membrane. The permeation is the results of diffusion and interaction. It is concluded that the permeation process is controlled by the rate of interaction between the alkali and PBI molecule. The second step is the relaxation process in the membrane. This step contributes more to the conductivity for the membrane than the first step. The ionic conductivity mechanism

  13. Negative electrodes for non-aqueous secondary batteries composed on conjugated polymer and alkali metal alloying or inserting material

    SciTech Connect

    Shacklette, L.W.; Jow, T.R.; Toth, E.; Maxfield, M.

    1987-05-26

    A battery is described comprising: an anode comprising as the anode active materials one or more conjugated backbone polymers and one or more electroactive materials selected from the group consisting of metals which alloy with alkali metals and alkali metal cation inserting materials; an electrolyte comprising an organic solvent and an alkali-metal salt, and a cathode. The alkali-metal cations from the electrolyte are inserted into the anode as a metal alloy or as an inserted ion in the alkali metal cation inserting material during the charging of the battery.

  14. Contributions to the mixed-alkali effect in molecular dynamics simulations of alkali silicate glasses

    NASA Astrophysics Data System (ADS)

    Lammert, Heiko; Heuer, Andreas

    2005-12-01

    The mixed-alkali effect in the cation dynamics in silicate glasses is analyzed via molecular dynamics simulations. Observations suggest a description of the dynamics in terms of stable sites mostly specific to one ionic species. As main contributions to the mixed-alkali slow down longer residence times and an increased probability of correlated backjumps are identified. The slow down is related to the limited accessibility of foreign sites. The mismatch experienced in a foreign site is stronger and more retarding for the larger ions, the smaller ions can be temporarily accommodated. Also correlations between unlike as well as like cations are demonstrated that support cooperative behavior.

  15. Process for the disposal of alkali metals

    DOEpatents

    Lewis, Leroy C.

    1977-01-01

    Large quantities of alkali metals may be safely reacted for ultimate disposal by contact with a hot concentrated caustic solution. The alkali metals react with water in the caustic solution in a controlled reaction while steam dilutes the hydrogen formed by the reaction to a safe level.

  16. Recovery of alkali metal constituents from catalytic coal conversion residues

    DOEpatents

    Soung, W.Y.

    In a coal gasification operation (32) or similar conversion process carried out in the presence of an alkali metal-containing catalyst wherein particles containing alkali metal residues are produced, alkali metal constituents are recovered from the particles by contacting them with water or an aqueous solution to remove water-soluble alkali metal constituents and produce an aqueous solution enriched in said constituents. The aqueous solution thus produced is then contacted with carbon dioxide to precipitate silicon constituents, the pH of the resultant solution is increased, preferably to a value in the range between about 12.5 and about 15.0, and the solution of increased pH is evaporated to increase the alkali metal concentration. The concentrated aqueous solution is then recycled to the conversion process where the alkali metal constituents serve as at least a portion of the alkali metal constituents which comprise the alkali metal-containing catalyst.

  17. Quantitative characterization of non-classic polarization of cations on clay aggregate stability.

    PubMed

    Hu, Feinan; Li, Hang; Liu, Xinmin; Li, Song; Ding, Wuquan; Xu, Chenyang; Li, Yue; Zhu, Longhui

    2015-01-01

    Soil particle interactions are strongly influenced by the concentration, valence and ion species and the pH of the bulk solution, which will also affect aggregate stability and particle transport. In this study, we investigated clay aggregate stability in the presence of different alkali ions (Li+, Na+, K+, and Cs+) at concentrations from10-5 to 10-1 mol L-1. Strong specific ion effects on clay aggregate stability were observed, and showed the order Cs+>K+>Na+>Li+. We found that it was not the effects of ion size, hydration, and dispersion forces in the cation-surface interactions but strong non-classic polarization of adsorbed cations that resulted in these specific effects. In this study, the non-classic dipole moments of each cation species resulting from the non-classic polarization were estimated. By comparing non-classic dipole moments with classic values, the observed dipole moments of adsorbed cations were up to 104 times larger than the classic values for the same cation. The observed non-classic dipole moments sharply increased with decreasing electrolyte concentration. We conclude that strong non-classic polarization could significantly suppress the thickness of the diffuse layer, thereby weakening the electric field near the clay surface and resulting in improved clay aggregate stability. Even though we only demonstrated specific ion effects on aggregate stability with several alkali ions, our results indicate that these effects could be universally important in soil aggregate stability. PMID:25874864

  18. Alkali metal nitrate purification

    DOEpatents

    Fiorucci, Louis C.; Morgan, Michael J.

    1986-02-04

    A process is disclosed for removing contaminants from impure alkali metal nitrates containing them. The process comprises heating the impure alkali metal nitrates in solution form or molten form at a temperature and for a time sufficient to effect precipitation of solid impurities and separating the solid impurities from the resulting purified alkali metal nitrates. The resulting purified alkali metal nitrates in solution form may be heated to evaporate water therefrom to produce purified molten alkali metal nitrates suitable for use as a heat transfer medium. If desired, the purified molten form may be granulated and cooled to form discrete solid particles of purified alkali metal nitrates.

  19. The effect of topography and rock type on soil cation contents and stream solute and phosphorus concentrations of streams in the southwestern Brazilian Amazon basin.

    NASA Astrophysics Data System (ADS)

    Biggs, T. W.; Dunne, T.; Holmes, K.; Martinelli, L. A.

    2001-12-01

    Topography plays an important role in determining soil properties, stream solute concentrations and landscape denudation rates. Stallard (1985) suggested that catchment denudation rates should depend on soil thickness. Areas with low slopes are limited by the rate of transport of sediment, and typically contain thick soils that prevent interaction of stream waters with underlying bedrock [Stallard 1985]. Steep areas typically have thin soils, but a lower hydrologic residence time that may prevent soil water from coming into thermodynamic equilibrium with the soil-rock complex. In a survey of streams in the Brazilian Amazon basin, Biggs et al. (2001) found that stream solute concentrations correlate with soil cation contents in the humid tropics, but the mechanism underlying the correlation has not been determined. We combine chemical analyses of water samples from ~40 different streams with soil surveys, geology maps, and a 100m resolution DEM to examine the relationship between topography, rock type, soil cation contents, and stream solute concentrations in the Brazilian Amazon state of Rondônia. The basins are all more than 60% forested at the time of stream sampling and lie on granite-gneiss rocks, tertiary sediments, or sandstone. The catchment-averaged slope correlates positively with both soil cation contents and stream concentrations of P, Na, Ca, Mg, K, Si, ANC, and pH. Though we have no data about the relationship between soil depth and average slope, we assume an inverse correlation, so the data demonstrates that thick soils yield lower solute concentrations. Stream concentrations of Ca, Mg, ANC and pH reach a maximum at intermediate average slopes (3 degrees), suggesting that denudation rates may increase with slope up to a maximum, when the catchment becomes limited by the weathering rate of the basement rock. Catchments on mica-schists or mafic rocks have low average slopes and higher concentrations of Ca, Mg, Si, ANC, and pH than catchments on

  20. Milk-alkali syndrome

    MedlinePlus

    ... this page: //medlineplus.gov/ency/article/000332.htm Milk-alkali syndrome To use the sharing features on this page, please enable JavaScript. Milk-alkali syndrome is a condition in which there ...

  1. A method to buffer the concentrations of free Zn and Cd ions using a cation exchange resin in bacterial toxicity studies

    SciTech Connect

    Knight, B.; McGrath, S.P.

    1995-12-01

    The chemical form or species of metal present in a growth system is crucial to the toxicity of that metal. A growth medium is described in which the free metal concentration of either Zn or Cd is known. A method using a cation exchange resin as a buffer to maintain free metal ion concentrations during microbial growth is discussed. Using a buffered system, free concentrations of 3.4 {micro}g Cd L{sup {minus}1} and 57 {micro}g Zn L{sup {minus}1} reduced the growth rate of a sensitive isolate of Rhizobium leguminosarum biovar trifolii. The results demonstrate that to assess the true toxicity of Cd and Zn, the free ion concentration must be considered and that small free concentrations must be buffered.

  2. Cationized Magnetoferritin Enables Rapid Labeling and Concentration of Gram-Positive and Gram-Negative Bacteria in Magnetic Cell Separation Columns

    PubMed Central

    Spencer, J.; Schwarzacher, W.

    2016-01-01

    ABSTRACT In order to identify pathogens rapidly and reliably, bacterial capture and concentration from large sample volumes into smaller ones are often required. Magnetic labeling and capture of bacteria using a magnetic field hold great promise for achieving this goal, but the current protocols have poor capture efficiency. Here, we present a rapid and highly efficient approach to magnetic labeling and capture of both Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus aureus) bacteria using cationized magnetoferritin (cat-MF). Magnetic labeling was achieved within a 1-min incubation period with cat-MF, and 99.97% of the labeled bacteria were immobilized in commercially available magnetic cell separation (MACS) columns. Longer incubation times led to more efficient capture, with S. aureus being immobilized to a greater extent than E. coli. Finally, low numbers of magnetically labeled E. coli bacteria (<100 CFU per ml) were immobilized with 100% efficiency and concentrated 7-fold within 15 min. Therefore, our study provides a novel protocol for rapid and highly efficient magnetic labeling, capture, and concentration of both Gram-positive and Gram-negative bacteria. IMPORTANCE Antimicrobial resistance (AMR) is a significant global challenge. Rapid identification of pathogens will retard the spread of AMR by enabling targeted treatment with suitable agents and by reducing inappropriate antimicrobial use. Rapid detection methods based on microfluidic devices require that bacteria are concentrated from large volumes into much smaller ones. Concentration of bacteria is also important to detect low numbers of pathogens with confidence. Here, we demonstrate that magnetic separation columns capture small amounts of bacteria with 100% efficiency. Rapid magnetization was achieved by exposing bacteria to cationic magnetic nanoparticles, and magnetized bacteria were concentrated 7-fold inside the column. Thus, bacterial capture and concentration were achieved

  3. Actinide cation-cation complexes

    SciTech Connect

    Stoyer, N.J.; Seaborg, G.T.

    1994-12-01

    The +5 oxidation state of U, Np, Pu, and Am is a linear dioxo cation (AnO{sub 2}{sup +}) with a formal charge of +1. These cations form complexes with a variety of other cations, including actinide cations. Other oxidation states of actinides do not form these cation-cation complexes with any cation other than AnO{sub 2}{sup +}; therefore, cation-cation complexes indicate something unique about AnO{sub 2}{sup +} cations compared to actinide cations in general. The first cation-cation complex, NpO{sub 2}{sup +}{center_dot}UO{sub 2}{sup 2+}, was reported by Sullivan, Hindman, and Zielen in 1961. Of the four actinides that form AnO{sub 2}{sup +} species, the cation-cation complexes of NpO{sub 2}{sup +} have been studied most extensively while the other actinides have not. The only PuO{sub 2}{sup +} cation-cation complexes that have been studied are with Fe{sup 3+} and Cr{sup 3+} and neither one has had its equilibrium constant measured. Actinides have small molar absorptivities and cation-cation complexes have small equilibrium constants; therefore, to overcome these obstacles a sensitive technique is required. Spectroscopic techniques are used most often to study cation-cation complexes. Laser-Induced Photacoustic Spectroscopy equilibrium constants for the complexes NpO{sub 2}{sup +}{center_dot}UO{sub 2}{sup 2+}, NpO{sub 2}{sup +}{center_dot}Th{sup 4+}, PuO{sub 2}{sup +}{center_dot}UO{sub 2}{sup 2+}, and PuO{sub 2}{sup +}{center_dot}Th{sup 4+} at an ionic strength of 6 M using LIPAS are 2.4 {plus_minus} 0.2, 1.8 {plus_minus} 0.9, 2.2 {plus_minus} 1.5, and {approx}0.8 M{sup {minus}1}.

  4. Conserved Glutamate Residues Glu-343 and Glu-519 Provide Mechanistic Insights into Cation/Nucleoside Cotransport by Human Concentrative Nucleoside Transporter hCNT3*

    PubMed Central

    Slugoski, Melissa D.; Smith, Kyla M.; Ng, Amy M. L.; Yao, Sylvia Y. M.; Karpinski, Edward; Cass, Carol E.; Baldwin, Stephen A.; Young, James D.

    2009-01-01

    Human concentrative nucleoside transporter 3 (hCNT3) utilizes electrochemical gradients of both Na+ and H+ to accumulate pyrimidine and purine nucleosides within cells. We have employed radioisotope flux and electrophysiological techniques in combination with site-directed mutagenesis and heterologous expression in Xenopus oocytes to identify two conserved pore-lining glutamate residues (Glu-343 and Glu-519) with essential roles in hCNT3 Na+/nucleoside and H+/nucleoside cotransport. Mutation of Glu-343 and Glu-519 to aspartate, glutamine, and cysteine severely compromised hCNT3 transport function, and changes included altered nucleoside and cation activation kinetics (all mutants), loss or impairment of H+ dependence (all mutants), shift in Na+:nucleoside stoichiometry from 2:1 to 1:1 (E519C), complete loss of catalytic activity (E519Q) and, similar to the corresponding mutant in Na+-specific hCNT1, uncoupled Na+ currents (E343Q). Consistent with close-proximity integration of cation/solute-binding sites within a common cation/permeant translocation pore, mutation of Glu-343 and Glu-519 also altered hCNT3 nucleoside transport selectivity. Both residues were accessible to the external medium and inhibited by p-chloromercuribenzene sulfonate when converted to cysteine. PMID:19380587

  5. Quantitative Characterization of Non-Classic Polarization of Cations on Clay Aggregate Stability

    PubMed Central

    Hu, Feinan; Li, Hang; Liu, Xinmin; Li, Song; Ding, Wuquan; Xu, Chenyang; Li, Yue; Zhu, Longhui

    2015-01-01

    Soil particle interactions are strongly influenced by the concentration, valence and ion species and the pH of the bulk solution, which will also affect aggregate stability and particle transport. In this study, we investigated clay aggregate stability in the presence of different alkali ions (Li+, Na+, K+, and Cs+) at concentrations from10−5 to 10−1 mol L−1. Strong specific ion effects on clay aggregate stability were observed, and showed the order Cs+>K+>Na+>Li+. We found that it was not the effects of ion size, hydration, and dispersion forces in the cation–surface interactions but strong non-classic polarization of adsorbed cations that resulted in these specific effects. In this study, the non-classic dipole moments of each cation species resulting from the non-classic polarization were estimated. By comparing non-classic dipole moments with classic values, the observed dipole moments of adsorbed cations were up to 104 times larger than the classic values for the same cation. The observed non-classic dipole moments sharply increased with decreasing electrolyte concentration. We conclude that strong non-classic polarization could significantly suppress the thickness of the diffuse layer, thereby weakening the electric field near the clay surface and resulting in improved clay aggregate stability. Even though we only demonstrated specific ion effects on aggregate stability with several alkali ions, our results indicate that these effects could be universally important in soil aggregate stability. PMID:25874864

  6. Alkali-metal azides interacting with metal-organic frameworks.

    PubMed

    Armata, Nerina; Cortese, Remedios; Duca, Dario; Triolo, Roberto

    2013-01-14

    Interactions between alkali-metal azides and metal-organic framework (MOF) derivatives, namely, the first and third members of the isoreticular MOF (IRMOF) family, IRMOF-1 and IRMOF-3, are studied within the density functional theory (DFT) paradigm. The investigations take into account different models of the selected IRMOFs. The mutual influence between the alkali-metal azides and the π rings or Zn centers of the involved MOF derivatives are studied by considering the interactions both of the alkali-metal cations with model aromatic centers and of the alkali-metal azides with distinct sites of differently sized models of IRMOF-1 and IRMOF-3. Several exchange and correlation functionals are employed to calculate the corresponding interaction energies. Remarkably, it is found that, with increasing alkali-metal atom size, the latter decrease for cations interacting with the π-ring systems and increase for the azides interacting with the MOF fragments. The opposite behavior is explained by stabilization effects on the azide moieties and determined by the Zn atoms, which constitute the inorganic vertices of the IRMOF species. Larger cations can, in fact, coordinate more efficiently to both the aromatic center and the azide anion, and thus stabilizing bridging arrangements of the azide between one alkali-metal and two Zn atoms in an η(2) coordination mode are more favored. PMID:23161861

  7. Electrochemical cell utilizing molten alkali metal electrode-reactant

    DOEpatents

    Virkar, Anil V.; Miller, Gerald R.

    1983-11-04

    An improved electrochemical cell comprising an additive-modified molten alkali metal electrode-reactant and/or electrolyte is disclosed. Various electrochemical cells employing a molten alkali metal, e.g., sodium, electrode in contact with a cationically conductive ceramic membrane experience a lower resistance and a lower temperature coefficient of resistance whenever small amounts of selenium are present at the interface of the electrolyte and the molten alkali metal. Further, cells having small amounts of selenium present at the electrolyte-molten metal interface exhibit less degradation of the electrolyte under long term cycling conditions.

  8. Elucidation of transport mechanism and enhanced alkali ion transference numbers in mixed alkali metal-organic ionic molten salts.

    PubMed

    Chen, Fangfang; Forsyth, Maria

    2016-07-28

    Mixed salts of Ionic Liquids (ILs) and alkali metal salts, developed as electrolytes for lithium and sodium batteries, have shown a remarkable ability to facilitate high rate capability for lithium and sodium electrochemical cycling. It has been suggested that this may be due to a high alkali metal ion transference number at concentrations approaching 50 mol% Li(+) or Na(+), relative to lower concentrations. Computational investigations for two IL systems illustrate the formation of extended alkali-anion aggregates as the alkali metal ion concentration increases. This tends to favor the diffusion of alkali metal ions compared with other ionic species in electrolyte solutions; behavior that has recently been reported for Li(+) in a phosphonium ionic liquid, thus an increasing alkali transference number. The mechanism of alkali metal ion diffusion via this extended coordination environment present at high concentrations is explained and compared to the dynamics at lower concentrations. Heterogeneous alkali metal ion dynamics are also evident and, somewhat counter-intuitively, it appears that the faster ions are those that are generally found clustered with the anions. Furthermore these fast alkali metal ions appear to correlate with fastest ionic liquid solvent ions. PMID:27375042

  9. Structural modulation of molybdenyl iodate architectures by alkali metal cations in AMoO3(IO3) (A = K, Rb, Cs): a facile route to new polar materials with large SHG responses.

    PubMed

    Sykora, Richard E; Ok, Kang Min; Halasyamani, P Shiv; Albrecht-Schmitt, Thomas E

    2002-03-01

    Three new molybdenyl iodates, KMoO3(IO3) (1), RbMoO3(IO3) (2), and CsMoO3(IO3) (3), have been prepared through the hydrothermal reactions of MoO3 with AIO4 (A = K, Rb, or Cs) at 180 C. These compounds are isolated as nearly colorless, air-stable crystals. Single-crystal X-ray diffraction experiments reveal that 1 possesses a corrugated layered structure constructed from molybdenum oxide chains that are bridged by iodate anions. The puckering of the layers is caused by the alignment of bent molybdenyl (MoO2(2+)) groups along one side of the molybdenum oxide chains. The K+ cations separate these layers from one another and serve to balance charge. In contrast, compounds 2 and 3, which are isostructural, form three-dimensional structures with small cavities filled with Rb+ or Cs+ cations. The differences between the structures of 1 and those of 2 and 3 are due to rotation of the molybdenyl units as translation occurs down the molybdenum oxide chains in order to accommodate the increased size of the Rb+ and Cs+ cations. This rotation allows for the iodate anions to bridge the molybdenum oxide chains in an additional dimension, creating a three-dimensional network structure. Furthermore, while 1 crystallizes in a centrosymmetric space group, 2 and 3 crystallize in polar space groups. Second-harmonic generation measurements on 2 and 3 show large responses of 400x alpha-quartz. Differential scanning calorimetry measurements demonstrate that 2 and 3 are thermally stable to 494 and 486 C, respectively. UV-vis diffuse reflectance spectra of these compounds show a high degree of transparency from 1 to 3 eV and a band gap of 3.1 eV. PMID:11866608

  10. Regulation of Cation Balance in Saccharomyces cerevisiae

    PubMed Central

    Cyert, Martha S.; Philpott, Caroline C.

    2013-01-01

    All living organisms require nutrient minerals for growth and have developed mechanisms to acquire, utilize, and store nutrient minerals effectively. In the aqueous cellular environment, these elements exist as charged ions that, together with protons and hydroxide ions, facilitate biochemical reactions and establish the electrochemical gradients across membranes that drive cellular processes such as transport and ATP synthesis. Metal ions serve as essential enzyme cofactors and perform both structural and signaling roles within cells. However, because these ions can also be toxic, cells have developed sophisticated homeostatic mechanisms to regulate their levels and avoid toxicity. Studies in Saccharomyces cerevisiae have characterized many of the gene products and processes responsible for acquiring, utilizing, storing, and regulating levels of these ions. Findings in this model organism have often allowed the corresponding machinery in humans to be identified and have provided insights into diseases that result from defects in ion homeostasis. This review summarizes our current understanding of how cation balance is achieved and modulated in baker’s yeast. Control of intracellular pH is discussed, as well as uptake, storage, and efflux mechanisms for the alkali metal cations, Na+ and K+, the divalent cations, Ca2+ and Mg2+, and the trace metal ions, Fe2+, Zn2+, Cu2+, and Mn2+. Signal transduction pathways that are regulated by pH and Ca2+ are reviewed, as well as the mechanisms that allow cells to maintain appropriate intracellular cation concentrations when challenged by extreme conditions, i.e., either limited availability or toxic levels in the environment. PMID:23463800

  11. Effect of pH and monovalent cations on the Raman spectrum of water: Basics revisited and application to measure concentration gradients at water/solid interface in Si3N4 biomaterial

    NASA Astrophysics Data System (ADS)

    Pezzotti, Giuseppe; Puppulin, Leonardo; La Rosa, Angelo; Boffelli, Marco; Zhu, Wenliang; McEntire, Bryan J.; Hosogi, Shigekuni; Nakahari, Takashi; Marunaka, Yoshinori

    2015-12-01

    The effect of hydrogen carbonate (HCO3-) and cations (Na+, K+) solvated in water were revisited according to high spectrally resolved Raman measurements. Water solutions with different bicarbonate concentrations or added with increasing amounts of monovalent cations were examined with respect to their Raman spectra both in the bulk state and at the solid/liquid interface with a silicon nitride (Si3N4) bioceramic. Spectroscopic calibrations confirmed that the Raman emission from OH-stretching in water is sensitive to molarity variations (in the order of tens of mM). The concentration gradient developed at the solid/liquid interface in cation-added solutions interacting with a Si3N4 surface was measured and found to be peculiar to individual cations. Local variation in pH was detected in ionic solutions interacting with Si3N4 samples, which might represent a useful property for Si3N4 in a number of biomedical applications.

  12. Study of the adsorption of Cd and Zn onto an activated carbon: Influence of pH, cation concentration, and adsorbent concentration

    SciTech Connect

    Seco, A.; Marzal, P.; Gabaldon, C.; Ferrer, J.

    1999-06-01

    The single adsorption of Cd and Zn from aqueous solutions has been investigated on Scharlau Ca 346 granular activated carbon in a wide range of experimental conditions: pH, metal concentration, and carbon concentration. The results showed the efficiency of the activated carbon as sorbent for both metals. Metal removals increase on raising the pH and carbon concentration, and decrease on raising the initial metal concentration. The adsorption processes have been modeled using the surface complex formation (SCF) Triple Layer Model (TLM). The adsorbent TLM parameters were determined. Modeling has been performed assuming a single surface bidentate species or an overall surface species with fractional stoichiometry. The bidentate stoichiometry successfully predicted cadmium and zinc removals in all the experimental conditions. The Freundlich isotherm has been also checked.

  13. Competition effects in cation binding to humic acid: Conditional affinity spectra for fixed total metal concentration conditions

    NASA Astrophysics Data System (ADS)

    David, Calin; Mongin, Sandrine; Rey-Castro, Carlos; Galceran, Josep; Companys, Encarnació; Garcés, José Luis; Salvador, José; Puy, Jaume; Cecilia, Joan; Lodeiro, Pablo; Mas, Francesc

    2010-09-01

    Information on the Pb and Cd binding to a purified Aldrich humic acid (HA) is obtained from the influence of different fixed total metal concentrations on the acid-base titrations of this ligand. NICA (Non-Ideal Competitive Adsorption) isotherm has been used for a global quantitative description of the binding, which has then been interpreted by plotting the Conditional Affinity Spectra of the H + binding at fixed total metal concentrations (CAScTM). This new physicochemical tool, here introduced, allows the interpretation of binding results in terms of distributions of proton binding energies. A large increase in the acidity of the phenolic sites as the total metal concentration increases, especially in presence of Pb, is revealed from the shift of the CAScTM towards lower affinities. The variance of the CAScTM distribution, which can be used as a direct measure of the heterogeneity, also shows a significant dependence on the total metal concentration. A discussion of the factors that influence the heterogeneity of the HA under the conditions of each experiment is provided, so that the smoothed pattern exhibited by the titration curves can be justified.

  14. (abstract) Fundamental Mechanisms of Electrode Kinetics and Alkali Metal Atom Transport at the Alkali Beta'-Alumina/Porous Electrode/Alkali Metal Vapor Three Phase Boundary

    NASA Technical Reports Server (NTRS)

    Williams, R. M.; Jeffries-Nakamura, B.; Ryan, M. A.; Underwood, M. L.; O'Connor, D.; Kisor, A.; Kikkert, S. K.

    1993-01-01

    The mechanisms of electrode kinetics and mass transport of alkali metal oxidation and alkali metal cation reduction at the solid electrolyte/porous electrode boundary as well as alkali metal transport through porous metal electrodes has important applications in optimizing device performance in alkali metal thermal to electric converter (AMTEC) cells which are high temperature, high current density electrochemical cells. Basic studies of these processes also affords the opportunity to investigate a very basic electrochemical reaction over a wide range of conditions; and a variety of mass transport modes at high temperatures via electrochemical techniques. The temperature range of these investigations covers 700K to 1240K; the alkali metal vapor pressures range from about 10(sup -2) to 10(sup 2) Pa; and electrodes studied have included Mo, W, Mo/Na(sub 2)MoO(sub 4), W/Na(sub 2)WO(sub 4), WPt(sub x), and WRh(sub x) (1.0 < x < 6.0 ) with Na at Na-beta'-alumina, and Mo with K at K-beta'-alumina. Both liquid metal/solid electrolyte/alkali metal vapor and alkali metal vapor/solid electrolyte/vapor cells have been used to characterize the reaction and transport processes. We have previously reported evidence of ionic, free molecular flow, and surface transport of sodium in several types of AMTEC electrodes.

  15. High-temperature corrosion of silicon nitride and mixed alkali effect

    NASA Astrophysics Data System (ADS)

    Jordache, Madeline K.

    Corrosion and associated degradation of silicon nitride (Si3N 4) remains an obstacle to its utilization in high-temperature turbines. This research consists of three interrelated components: comparative and comprehensive study of the oxidation behavior of three types of Si3N4 (turbine-grade Kyocera SN 282 sintered with Lu2O3, Toshiba TSN 03-NH with Y2O3/Al2O3, and Norton NBD 200 with MgO) in dry O2; investigation of the role of Na and Cs in the corrosion resistance of SN 282; and exploration of the mixed alkali effect in improving the corrosion resistance of SN Si3N 4. SN 282, TSN 03-NH, and NBD 200 all follow a parabolic oxidation rate law when exposed in dry O2 at 930°C--1200°C, indicating a diffusion-limited oxidation process. The oxidation rate decreases in order of NBD 200, TSN 03-NH, and SN 282 due to increased crystallinity and refractoriness of the intergranular phases. The activation energies for oxidation of NBD 200, TSN 03-NH, and SN 282 are 259, 205, 107 KJ/mol, respectively. Inward diffusion of molecular oxygen O2 through the oxide layer is the rate-controlling step for oxidation of SN 282. In contrast, outward diffusion of additive cations in the underlying Si3N4 is the rate-limiting mechanism for oxidation of TSN 03-NH and NBD 200. Na and Cs, separately introduced in vapor form of the corresponding nitrates, accelerate the corrosion of SN 282 due to their fluxing effect on the oxide, leading to rapid diffusion of O2. The adverse effect on the corrosion resistance of SN 282 is more pronounced in Cs than in Na that can be attributed to the larger negative Gibbs free energy for dissolution of SiO2 in Cs silicate than in Na silicate. Co-introduction of Na and Cs via vapor mixtures of their nitrates at a fixed alkali concentration but varying Na/Cs ratios revealed the presence of the mixed alkali effect in corrosion for the first time, i.e., the addition of a dissimilar alkali species reduces the overall detrimental effect on the corrosion resistance of

  16. Determination of cationic surfactants by capillary zone electrophoresis and micellar electrokinetic chromatography with deoxycholate micelles in the presence of large organic solvent concentrations.

    PubMed

    Herrero-Martínez, J M; Simó-Alfonso, E F; Mongay-Fernández, C; Ramis-Ramos, G

    2000-10-20

    Mixtures of the cationic surfactants benzalkonium chloride (BKC) and cetylpyridinium chloride (CPC) were quickly resolved and reproducibly and reliably determined by using background electrolytes (BGEs) containing 80 mM borate, pH 8.5, bile salts and large concentrations of an organic solvent. When the bile salt is present, the separation mechanism changes from capillary zone electrophoresis (CZE) to a mixed micellar electrokinetic chromatography (MEKC)-CZE, with predominant MEKC interactions, which lead to an excellent resolution of all the solutes, including the C12-C18 homologues of BKC and CPC. A BGE containing 50 mM sodium deoxycholate and 30% ethanol for an extreme resolution, or 20% tetrahydrofuran for an adequate resolution within a much shorter analysis time, is recommended. The procedure was applied to the determination of the surfactants in industrial and household formulations, with excellent resolution between the homologues, detection limits of a few microg ml(-1) and reproducibilities below 2%. PMID:11105866

  17. K{sub 2}NaOsO{sub 5.5} and K{sub 3}NaOs{sub 2}O{sub 9}: The first osmium perovskites containing alkali cations at the 'A' site

    SciTech Connect

    Mogare, Kailash M.; Klein, Wilhelm; Jansen, Martin

    2012-07-15

    K{sub 2}NaOsO{sub 5.5} and K{sub 3}NaOs{sub 2}O{sub 9} were obtained from solid-state reactions of potassium superoxide, sodium peroxide and osmium metal at elevated oxygen pressures. K{sub 2}NaOsO{sub 5.5} crystallizes as an oxygen-deficient cubic double perovskite in space group Fm3{sup Macron }m with a=8.4184(5) A and contains isolated OsO{sub 6} octahedra. K{sub 3}NaOs{sub 2}O{sub 9} crystallizes hexagonally in P6{sub 3}/mmc with a=5.9998(4) A and c=14.3053(14) A. K{sub 3}NaOs{sub 2}O{sub 9} consists of face sharing Os{sub 2}O{sub 9} pairs of octahedra. According to magnetic measurements K{sub 2}NaOsO{sub 5.5} is diamagnetic, whereas K{sub 3}NaOs{sub 2}O{sub 9} displays strong antiferromagnetic coupling (T{sub N}=140 K), indicating enhanced magnetic interactions within the octahedral pair. - Graphical abstract: High oxidation states of Os, obtained by high oxygen pressure synthesis, are accommodated in double and triple perovskite matrices. K{sub 3}NaOs{sub 2}O{sub 9} displays enhanced magnetic interactions. Highlights: Black-Right-Pointing-Pointer New osmates containing highly oxidized Os were obtained by high O{sub 2} pressure synthesis. Black-Right-Pointing-Pointer High oxidation states of Os are accommodated in double and triple perovskite matrices. Black-Right-Pointing-Pointer Both compounds represent the first Os perovskites with an alkali metal at the A site. Black-Right-Pointing-Pointer K{sub 3}NaOs{sub 2}O{sub 9} displays enhanced magnetic interactions within the octahedral pair.

  18. Supplemental leucine and isoleucine affect expression of cationic amino acid transporters and myosin, serum concentration of amino acids, and growth performance of pigs.

    PubMed

    Cervantes-Ramírez, M; Mendez-Trujillo, V; Araiza-Piña, B A; Barrera-Silva, M A; González-Mendoza, D; Morales-Trejo, A

    2013-01-01

    Leucine (Leu) participates in the activity of cationic amino acid (aa) transporters. Also, branched-chain aa [Leu, isoleucine (Ile), and valine (Val)] share intestinal transporters for absorption. We conducted an experiment with 16 young pigs (body weight of about 16 kg) to determine whether Leu and Ile affect expression of aa transporters b(0,+) and CAT-1 in the jejunum and expression of myosin in muscle, as well as serum concentration of essential aa, and growth performance in pigs. Dietary treatments were: wheat-based diets fortified with Lys, Thr, and Met; basal diet plus 0.50% Leu; basal diet plus 0.50% Ile, and basal diet plus 0.50% Leu and 0.50% Ile. After 28 days, the pigs were sacrificed to collect blood, jejunum, and semitendinosus and longissimus muscle samples. The effects of single and combined addition of Leu and Ile were analyzed. Leu alone or combined with Ile significantly decreased daily weight gain and reduced feed conversion. Leu and Ile, alone or in combination, significantly decreased expression of b(0,+) and significantly increased CAT-1. Ile alone or combined with Leu significantly decreased myosin expression in semitendinosus and significantly decreased it in longissimus muscle. Leu alone significantly decreased Lys, Ile and Thr serum concentrations; Ile significantly decreased Thr serum concentration; combined Leu and Ile significantly decreased Thr and significantly increased Val serum concentration. We conclude that dietary levels of Leu and Ile affect growth performance, expression of aa transporters and myosin, and aa serum concentrations in pigs. PMID:23408397

  19. Rapid Method To Determine Intracellular Drug Concentrations in Cellular Uptake Assays: Application to Metformin in Organic Cation Transporter 1-Transfected Human Embryonic Kidney 293 Cells.

    PubMed

    Chien, Huan-Chieh; Zur, Arik A; Maurer, Tristan S; Yee, Sook Wah; Tolsma, John; Jasper, Paul; Scott, Dennis O; Giacomini, Kathleen M

    2016-03-01

    Because of the importance of intracellular unbound drug concentrations in the prediction of in vivo concentrations that are determinants of drug efficacy and toxicity, a number of assays have been developed to assess in vitro unbound concentrations of drugs. Here we present a rapid method to determine the intracellular unbound drug concentrations in cultured cells, and we apply the method along with a mechanistic model to predict concentrations of metformin in subcellular compartments of stably transfected human embryonic kidney 293 (HEK293) cells. Intracellular space (ICS) was calculated by subtracting the [(3)H]-inulin distribution volume (extracellular space, ECS) from the [(14)C]-urea distribution volume (total water space, TWS). Values obtained for intracellular space (mean ± S.E.M.; μl/10(6) cells) of monolayers of HEK cells (HEK-empty vector [EV]) and cells overexpressing human organic cation transporter 1 (HEK-OCT1), 1.21± 0.07 and 1.25±0.06, respectively, were used to determine the intracellular metformin concentrations. After incubation of the cells with 5 µM metformin, the intracellular concentrations were 26.4 ± 7.8 μM and 268 ± 11.0 μM, respectively, in HEK-EV and HEK-OCT1. In addition, intracellular metformin concentrations were lower in high K(+) buffer (140 mM KCl) compared with normal K(+) buffer (5.4 mM KCl) in HEK-OCT1 cells (54.8 ± 3.8 μM and 198.1 ± 11.2 μM, respectively; P < 0.05). Our mechanistic model suggests that, depending on the credible range of assumed physiologic values, the positively charged metformin accumulates to particularly high levels in endoplasmic reticulum and/or mitochondria. This method together with the computational model can be used to determine intracellular unbound concentrations and to predict subcellular accumulation of drugs in other complex systems such as primary cells. PMID:26700958

  20. The effects of acid and alkali modification on the adsorption performance of fuller's earth for basic dye.

    PubMed

    Hisarli, G

    2005-01-01

    The objective of this work was to prepare modified adsorbents from fuller's earth (FE) by acid and alkali treatment for enhancement cationic dye adsorption. Toluidine blue (TB) was selected as adsorbate for evaluating the adsorption performance of fuller's earth samples, which was affected significantly by acid and alkali modification. The adsorption of TB was studied by visible spectra. The absorption band of the monomer at low loading of TB in FE suspension with respect to its maximum in aqueous solution is red-shifted, which is related to accessibility of dye interlamellar space in the presence of positively charged surface sites. Since all surfaces are negatively charged under experimental conditions, this effect has not been observed in acid- and alkali-treated FE suspensions. It was seen that the adsorption capacity of alkali-treated surface (FEAl) for TB was higher than these of acid-treated adsorbent (FEAc) and FE. Scanning electron micrographs (SEM) and X-ray diffraction (XRD) and fluorescence (XRF) spectra were applied to analyze the structure of the raw and modified FE samples. Absence of any identifiable amount of a crystalline compound in the solid reaction products after acid treatment was confirmed by XRD and SEM, whereas the crystalline form of FEAl was preserved. Experimental data for high-concentration regions were well described by Freundlich and Langmuir adsorption equations. The thermodynamic parameters were estimated for FE, FEAc, and FEAl by using temperature dependence of adsorption equilibrium constants. PMID:15567375

  1. Stimulation of TRPC5 cationic channels by low micromolar concentrations of lead ions (Pb{sup 2+})

    SciTech Connect

    Sukumar, Piruthivi; Beech, David J.

    2010-02-26

    Lead toxicity is long-recognised but continues to be a major public health problem. Its effects are wide-ranging and include induction of hyper-anxiety states. In general it is thought to act by interfering with Ca{sup 2+} signalling but specific targets are not clearly identified. Transient receptor potential canonical 5 (TRPC5) is a Ca{sup 2+}-permeable ion channel that is linked positively to innate fear responses and unusual amongst ion channels in being stimulated by trivalent lanthanides, which include gadolinium. Here we show investigation of the effect of lead, which is a divalent ion (Pb{sup 2+}). Intracellular Ca{sup 2+} and whole-cell patch-clamp recordings were performed on HEK 293 cells conditionally over-expressing TRPC5 or other TRP channels. Extracellular application of Pb{sup 2+} stimulated TRPC5 at concentrations greater than 1 {mu}M. Control cells without TRPC5 showed little or no response to Pb{sup 2+} and expression of other TRP channels (TRPM2 or TRPM3) revealed partial inhibition by 10 {mu}M Pb{sup 2+}. The stimulatory effect on TRPC5 depended on an extracellular residue (E543) near the ion pore: similar to gadolinium action, E543Q TRPC5 was resistant to Pb{sup 2+} but showed normal stimulation by the receptor agonist sphingosine-1-phosphate. The study shows that Pb{sup 2+} is a relatively potent stimulator of the TRPC5 channel, generating the hypothesis that a function of the channel is to sense metal ion poisoning.

  2. Surface charge density on silica in alkali and alkaline earth chloride electrolyte solutions

    NASA Astrophysics Data System (ADS)

    Dove, Patricia M.; Craven, Colin M.

    2005-11-01

    The surface charge density of colloidal SiO 2 (Aerosil 380) was measured in alkali chloride (0.067 and 0.20 M LiCl, NaCl, and KCl) and alkaline earth chloride (0.067 M MgCl 2, CaCl 2, SrCl 2, BaCl 2) solutions. Measurements were conducted at 25°C by potentiometric titrations using the constant ionic medium method in a CO 2-free system. The experimental design measured surface charge for solutions with constant ionic strength as well as constant cation concentration. Alkali chloride solutions promote negative surface charge density in the order LiCl < NaCl < KCl to give the "regular" lyotropic behavior previously reported. In contrast, the alkaline earth chloride solutions exhibit a reversed lyotropic trend with increasing crystallographic radius where increasing negative charge is promoted in the order BaCl 2 < SrCl 2 < CaCl 2 < MgCl 2. The origin of the opposing affinity trends is probed by testing the hypothesis that this reversal is rooted in the differing solvent structuring characteristics of the IA and IIA cations at the silica-water interface. This idea arises from earlier postulations that solvent structuring effects increase entropy through solvent disordering and these gains must be much greater than the small, positive enthalpy associated with electrostatic interactions. By correlating measured charge density with a proxy for the solvent-structuring ability of cations, this study shows that silica surface charge density is maximized by those electrolytes that have the strongest effects on solvent structuring. We suggest that for a given solid material, solvation entropy has a role in determining the ionic specificity of electrostatic interactions and reiterate the idea that the concept of lyotropy is rooted in the solvent-structuring ability of cations at the interface.

  3. Alkali slurry ozonation to produce a high capacity nickel battery material

    DOEpatents

    Jackovitz, John F.; Pantier, Earl A.

    1984-11-06

    A high capacity battery material is made, consisting essentially of hydrated Ni(II) hydroxide, and about 5 wt. % to about 40 wt. % of Ni(IV) hydrated oxide interlayer doped with alkali metal cations selected from potassium, sodium and lithium cations.

  4. Alkali Metal Ion Complexes with Phosphates, Nucleotides, Amino Acids, and Related Ligands of Biological Relevance. Their Properties in Solution.

    PubMed

    Crea, Francesco; De Stefano, Concetta; Foti, Claudia; Lando, Gabriele; Milea, Demetrio; Sammartano, Silvio

    2016-01-01

    Alkali metal ions play very important roles in all biological systems, some of them are essential for life. Their concentration depends on several physiological factors and is very variable. For example, sodium concentrations in human fluids vary from quite low (e.g., 8.2 mmol dm(-3) in mature maternal milk) to high values (0.14 mol dm(-3) in blood plasma). While many data on the concentration of Na(+) and K(+) in various fluids are available, the information on other alkali metal cations is scarce. Since many vital functions depend on the network of interactions occurring in various biofluids, this chapter reviews their complex formation with phosphates, nucleotides, amino acids, and related ligands of biological relevance. Literature data on this topic are quite rare if compared to other cations. Generally, the stability of alkali metal ion complexes of organic and inorganic ligands is rather low (usually log K < 2) and depends on the charge of the ligand, owing to the ionic nature of the interactions. At the same time, the size of the cation is an important factor that influences the stability: very often, but not always (e.g., for sulfate), it follows the trend Li(+) > Na(+) > K(+) > Rb(+) > Cs(+). For example, for citrate it is: log K ML = 0.88, 0.80, 0.48, 0.38, and 0.13 at 25 °C and infinite dilution. Some considerations are made on the main aspects related to the difficulties in the determination of weak complexes. The importance of the alkali metal ion complexes was also studied in the light of modelling natural fluids and in the use of these cations as probes for different processes. Some empirical relationships are proposed for the dependence of the stability constants of Na(+) complexes on the ligand charge, as well as for correlations among log K values of NaL, KL or LiL species (L = generic ligand). PMID:26860301

  5. Apparatus enables accurate determination of alkali oxides in alkali metals

    NASA Technical Reports Server (NTRS)

    Dupraw, W. A.; Gahn, R. F.; Graab, J. W.; Maple, W. E.; Rosenblum, L.

    1966-01-01

    Evacuated apparatus determines the alkali oxide content of an alkali metal by separating the metal from the oxide by amalgamation with mercury. The apparatus prevents oxygen and moisture from inadvertently entering the system during the sampling and analytical procedure.

  6. Phytic Acid Synthesis and Vacuolar Accumulation in Suspension-Cultured Cells of Catharanthus roseus Induced by High Concentration of Inorganic Phosphate and Cations1[w

    PubMed Central

    Mitsuhashi, Naoto; Ohnishi, Miwa; Sekiguchi, Yoko; Kwon, Yong-Uk; Chang, Young-Tae; Chung, Sung-Kee; Inoue, Yoshinori; Reid, Robert J.; Yagisawa, Hitoshi; Mimura, Tetsuro

    2005-01-01

    We have established a new system for studying phytic acid, myo-inositol hexakisphosphate (InsP6) synthesis in suspension-cultured cells of Catharanthus. InsP6 and other intermediates of myo-inositol (Ins) phosphate metabolism were measured using an ion chromatography method. The detection limit for InsP6 was less than 50 nm, which was sufficient to analyze Ins phosphates in living cells. Synthesis of Ins phosphates was induced by incubation in high inorganic phosphate medium. InsP6 was mainly accumulated in vacuoles and was enhanced when cells were grown in high concentration of inorganic phosphates with the cations K+, Ca2+, or Zn2+. However, there was a strong tendency for InsP6 to accumulate in the vacuole in the presence of Ca2+ and in nonvacuolar compartments when supplied with Zn2+, possibly due to precipitation of InsP6 with Zn2+ in the cytosol. A vesicle transport inhibitor, brefeldin A, stimulated InsP6 accumulation. The amounts of both Ins(3)P1 myo-inositol monophosphate synthase, a key enzyme for InsP6 synthesis, and Ins(1,4,5)P3 kinase were unrelated to the level of accumulation of InsP6. The mechanisms for InsP6 synthesis and localization into vacuoles in plant cells are discussed. PMID:15965017

  7. Alkalis and Skin.

    PubMed

    Greenwood, John E; Tan, Jin Lin; Ming, Justin Choong Tzen; Abell, Andrew D

    2016-01-01

    The aim of this editorial is to provide an overview of the chemical interactions occurring in the skin of our patients on contact with alkaline agents. Strongly basic alkali is highly aggressive and will readily hydrolyze (or cleave) key biological molecules such as lipids and proteins. This phenomenon is known as saponification in the case of lipids and liquefactive denaturation for peptides and proteins. A short section on current first-aid concepts is included. A better understanding of the basic science behind alkali burns will make us better teachers and provide an insight into the urgency needed in treating these common and dangerous chemical injuries. PMID:26182072

  8. Recovery of alkali metal constituents from catalytic coal conversion residues

    DOEpatents

    Soung, Wen Y.

    1984-01-01

    In a coal gasification operation (32) or similar conversion process carried out in the presence of an alkali metal-containing catalyst wherein particles containing alkali metal residues are produced, alkali metal constituents are recovered from the particles by contacting them (46, 53, 61, 69) with water or an aqueous solution to remove water-soluble alkali metal constituents and produce an aqueous solution enriched in said constituents. The aqueous solution thus produced is then contacted with carbon dioxide (63) to precipitate silicon constituents, the pH of the resultant solution is increased (81), preferably to a value in the range between about 12.5 and about 15.0, and the solution of increased pH is evaporated (84) to increase the alkali metal concentration. The concentrated aqueous solution is then recycled to the conversion process (86, 18, 17) where the alkali metal constituents serve as at least a portion of the alkali metal constituents which comprise the alkali metal-containing catalyst.

  9. Alkali metal ion battery with bimetallic electrode

    SciTech Connect

    Boysen, Dane A; Bradwell, David J; Jiang, Kai; Kim, Hojong; Ortiz, Luis A; Sadoway, Donald R; Tomaszowska, Alina A; Wei, Weifeng; Wang, Kangli

    2015-04-07

    Electrochemical cells having molten electrodes having an alkali metal provide receipt and delivery of power by transporting atoms of the alkali metal between electrode environments of disparate chemical potentials through an electrochemical pathway comprising a salt of the alkali metal. The chemical potential of the alkali metal is decreased when combined with one or more non-alkali metals, thus producing a voltage between an electrode comprising the molten the alkali metal and the electrode comprising the combined alkali/non-alkali metals.

  10. Interfacial tension in immiscible mixtures of alkali halides.

    PubMed

    Lockett, Vera; Rukavishnikova, Irina V; Stepanov, Victor P; Tkachev, Nikolai K

    2010-02-01

    The interfacial tension of the liquid-phase interface in seven immiscible reciprocal ternary mixtures of lithium fluoride with the following alkali halides: CsCl, KBr, RbBr, CsBr, KI, RbI, and CsI was measured using the cylinder weighing method over a wide temperature range. It was shown that for all mixtures the interfacial tension gradually decreases with growing temperature. The interfacial tension of the reciprocal ternary mixtures at a given temperature increases both with the alkali cation radius (K(+) < Rb(+) < Cs(+)) and with the radius of the halogen anion (Cl(-) < Br(-) < I(-)). PMID:20094678

  11. Methods of recovering alkali metals

    DOEpatents

    Krumhansl, James L; Rigali, Mark J

    2014-03-04

    Approaches for alkali metal extraction, sequestration and recovery are described. For example, a method of recovering alkali metals includes providing a CST or CST-like (e.g., small pore zeolite) material. The alkali metal species is scavenged from the liquid mixture by the CST or CST-like material. The alkali metal species is extracted from the CST or CST-like material.

  12. High affinity capture and concentration of quinacrine in polymorphonuclear neutrophils via vacuolar ATPase-mediated ion trapping: Comparison with other peripheral blood leukocytes and implications for the distribution of cationic drugs

    SciTech Connect

    Roy, Caroline; Gagné, Valérie; Fernandes, Maria J.G.; Marceau, François

    2013-07-15

    Many cationic drugs are concentrated in acidic cell compartments due to low retro-diffusion of the protonated molecule (ion trapping), with an ensuing vacuolar and autophagic cytopathology. In solid tissues, there is evidence that phagocytic cells, e.g., histiocytes, preferentially concentrate cationic drugs. We hypothesized that peripheral blood leukocytes could differentially take up a fluorescent model cation, quinacrine, depending on their phagocytic competence. Quinacrine transport parameters were determined in purified or total leukocyte suspensions at 37 °C. Purified polymorphonuclear leukocytes (PMNLs, essentially neutrophils) exhibited a quinacrine uptake velocity inferior to that of lymphocytes, but a consistently higher affinity (apparent K{sub M} 1.1 vs. 6.3 μM, respectively). However, the vacuolar (V)-ATPase inhibitor bafilomycin A1 prevented quinacrine transport or initiated its release in either cell type. PMNLs capture most of the quinacrine added at low concentrations to fresh peripheral blood leukocytes compared with lymphocytes and monocytes (cytofluorometry). Accumulation of the autophagy marker LC3-II occurred rapidly and at low drug concentrations in quinacrine-treated PMNLs (significant at ≥ 2.5 μM, ≥ 2 h). Lymphocytes contained more LAMP1 than PMNLs, suggesting that the mass of lysosomes and late endosomes is a determinant of quinacrine uptake V{sub max}. PMNLs, however, exhibited the highest capacity for pinocytosis (uptake of fluorescent dextran into endosomes). The selectivity of quinacrine distribution in peripheral blood leukocytes may be determined by the collaboration of a non-concentrating plasma membrane transport mechanism, tentatively identified as pinocytosis in PMNLs, with V-ATPase-mediated concentration. Intracellular reservoirs of cationic drugs are a potential source of toxicity (e.g., loss of lysosomal function in phagocytes). - Highlights: • Quinacrine is concentrated in acidic organelles via V-ATPase-mediated ion

  13. Cation control of energetics on dye-sensitized nanocrystalline TiO2 for solar cells

    NASA Astrophysics Data System (ADS)

    Stux, Arnold M.

    Regenerative solar cells based on nanocrystalline TiO2 (anatase) and the dye Ru(deeb)(bpy)2(PF6)2, where deeb is 4,4'-(CO2CH2CH3)2-2,2 '-bipyridine and bpy is 2,2'-bipyridine, have increased efficiency when in the presence of a high concentration of cations with a large charge-to-radius ratio. Concentration-dependent photoluminescence (PL) quenching and increased quantum yield for interfacial charge separation have been explored for mono- and divalent cations by absorbance, time-resolved and steady-state PL. Cation adsorption stabilizes TiO2 acceptor states resulting in energetically favorable electron transfer from the dye into the semiconductor conduction band. Quenching of the PL of excited states is reversible. A new luminescence approach for sensing alkali and alkaline earth metal cations utilizes the surface-adsorption/desorption induced energetic shifts of a semiconductor conduction band to alter the electron transfer quenching efficiency of a photoluminescent dye such as Ru(deeb)(bpy)2(PF 6)2 anchored to TiO2 nanoparticles. This approach yields intensity, lifetime, and wavelength-ratiometric calcium ion sensors that are sensitive to 5 x 10-4 M concentrations. In situ photoluminescence of a regenerative solar cell has been demonstrated as a probe of injection and efficiencies. The smaller the alkali cation, the higher the photocurrent and the more quenched the photoluminescence. The extent of quenching in 0.1 M iodide/0.01 M iodine electrolytes was 10-fold with LiI and 3-fold with NaI. A millimolar threshold concentration is observed for Li+ at which point a red shift in absorbance and photoluminescence spectra concomitant with significant static and dynamic quenching occurs. For Na+, the threshold concentration for observable red shift is more than an order of magnitude higher than for Li+. Cation adsorption was also observed on planar TiO2 surfaces in the absence of dye. The flat band potentials of single crystal TiO 2 (rutile) with cations in propylene

  14. Ion Pairing in Alkali Nitrate Electrolyte Solutions.

    PubMed

    Xie, Wen Jun; Zhang, Zhen; Gao, Yi Qin

    2016-03-10

    In this study, we investigate the thermodynamics of alkali nitrate salt solutions, especially the formation of contact ion pairs between alkali cation and nitrate anion. The ion-pairing propensity shows an order of LiNO3 < NaNO3 < KNO3. Such results explain the salt activity coefficients and suggest that the empirical "law of matching water affinity" is followed by these alkali nitrate salt solutions. The spatial patterns of contact ion pairs are different in the three salt solutions studied here: Li(+) forms the contact ion pair with only one oxygen of the nitrate while Na(+) and K(+) can also be shared by two oxygens of the nitrate. In reproducing the salt activity coefficient using Kirkwood-Buff theory, we find that it is essential to include electronic polarization for Li(+) which has a high charge density. The electronic continuum correction for nonpolarizable force field significantly improves the agreement between the calculated activity coefficients and their experimental values. This approach also improves the performance of the force field on salt solubility. From these two aspects, this study suggests that electronic continuum correction can be a promising approach to force-field development for ions with high charge densities. PMID:26901167

  15. Alkali Metal Variation and Twisting of the FeNNFe Core in Bridging Diiron Dinitrogen Complexes.

    PubMed

    McWilliams, Sean F; Rodgers, Kenton R; Lukat-Rodgers, Gudrun; Mercado, Brandon Q; Grubel, Katarzyna; Holland, Patrick L

    2016-03-21

    Alkali metal cations can interact with Fe-N2 complexes, potentially enhancing back-bonding or influencing the geometry of the iron atom. These influences are relevant to large-scale N2 reduction by iron, such as in the FeMoco of nitrogenase and the alkali-promoted Haber-Bosch process. However, to our knowledge there have been no systematic studies of a large range of alkali metals regarding their influence on transition metal-dinitrogen complexes. In this work, we varied the alkali metal in [alkali cation]2[LFeNNFeL] complexes (L = bulky β-diketiminate ligand) through the size range from Na(+) to K(+), Rb(+), and Cs(+). The FeNNFe cores have similar Fe-N and N-N distances and N-N stretching frequencies despite the drastic change in alkali metal cation size. The two diketiminates twist relative to one another, with larger dihedral angles accommodating the larger cations. In order to explain why the twisting has so little influence on the core, we performed density functional theory calculations on a simplified LFeNNFeL model, which show that the two metals surprisingly do not compete for back-bonding to the same π* orbital of N2, even when the ligand planes are parallel. This diiron system can tolerate distortion of the ligand planes through compensating orbital energy changes, and thus, a range of ligand orientations can give very similar energies. PMID:26925968

  16. Chlor-Alkali Technology.

    ERIC Educational Resources Information Center

    Venkatesh, S.; Tilak, B. V.

    1983-01-01

    Chlor-alkali technology is one of the largest electrochemical industries in the world, the main products being chlorine and caustic soda (sodium hydroxide) generated simultaneously by the electrolysis of sodium chloride. This technology is reviewed in terms of electrochemical principles and manufacturing processes involved. (Author/JN)

  17. Alkali oxide-tantalum oxide and alkali oxide-niobium oxide ionic conductors

    NASA Technical Reports Server (NTRS)

    Roth, R. S.; Parker, H. S.; Brower, W. S.; Minor, D.

    1974-01-01

    A search was made for new cationic conducting phases in alkali-tantalate and niobate systems. The phase equilibrium diagrams were constructed for the six binary systems Nb2O5-LiNbO3, Nb2O5-NaNbO3, Nb2O5-KNbO3, Ta2O5-NaTaO3, Ta2O5-LiTaO3, and Ta2O5-KTaO3. Various other binary and ternary systems were also examined. Pellets of nineteen phases were evaluated (by the sponsoring agency) by dielectric loss measurements. Attempts were made to grow large crystals of eight different phases. The system Ta2O5-KTaO3 contains at least three phases which showed peaks in dielectric loss vs. temperature. All three contain structures related to the tungsten bronzes with alkali ions in non-stoichiometric crystallographic positions.

  18. A novel approach to measure elemental concentrations in cation exchange resins using XRF-scanning technique, and its potential in water pollution studies

    NASA Astrophysics Data System (ADS)

    Huang, Jyh-Jaan; Lin, Sheng-Chi; Löwemark, Ludvig; Liou, Ya-Hsuan; Chang, Queenie; Chang, Tsun-Kuo; Wei, Kuo-Yen; Croudace, Ian W.

    2016-04-01

    X-ray fluorescence (XRF) core-scanning is a fast, and convenient technique to assess elemental variations for a wide variety of research topics. However, the XRF scanning counts are often considered a semi-quantitative measurement due to possible absorption or scattering caused by down core variability in physical properties. To overcome this problem and extend the applications of XRF-scanning to water pollution studies, we propose to use cation exchange resin (IR-120) as an "elemental carrier", and to analyze the resins using the Itrax-XRF core scanner. The use of resin minimizes the matrix effects during the measurements, and can be employed in the field in great numbers due to its low price. Therefore, the fast, and non-destructive XRF-scanning technique can provide a quick and economical method to analyze environmental pollution via absorption in the resin. Five standard resin samples were scanned by the Itrax-XRF core scanner at different exposure times (1 s, 5 s, 15 s, 30 s, 100 s) to allow the comparisons of scanning counts with the absolute concentrations. The regression lines and correlation coefficients of elements that are generally used in pollution studies (Ca, Ti, Cr, Ni, Cu, Zn, and Pb) were examined for the different exposure times. The result shows that within the test range (from few ppm to thousands ppm), the correlation coefficients are all higher than 0.97, even at the shortest exposure time (1 s). Therefore, we propose to use this method in the field to monitor for example sewage disposal events. The low price of resin, and fast, multi elements and precise XRF-scanning technique provide a viable, cost- and time-effective approach that allows large sample numbers to be processed. In this way, the properties and sources of wastewater pollution can be traced for the purpose of environmental monitoring and environmental forensics.

  19. Alkali absorption and citrate excretion in calcium nephrolithiasis

    NASA Technical Reports Server (NTRS)

    Sakhaee, K.; Williams, R. H.; Oh, M. S.; Padalino, P.; Adams-Huet, B.; Whitson, P.; Pak, C. Y.

    1993-01-01

    The role of net gastrointestinal (GI) alkali absorption in the development of hypocitraturia was investigated. The net GI absorption of alkali was estimated from the difference between simple urinary cations (Ca, Mg, Na, and K) and anions (Cl and P). In 131 normal subjects, the 24 h urinary citrate was positively correlated with the net GI absorption of alkali (r = 0.49, p < 0.001). In 11 patients with distal renal tubular acidosis (RTA), urinary citrate excretion was subnormal relative to net GI alkali absorption, with data from most patients residing outside the 95% confidence ellipse described for normal subjects. However, the normal relationship between urinary citrate and net absorbed alkali was maintained in 11 patients with chronic diarrheal syndrome (CDS) and in 124 stone-forming patients devoid of RTA or CDS, half of whom had "idiopathic" hypocitraturia. The 18 stone-forming patients without RTA or CDS received potassium citrate (30-60 mEq/day). Both urinary citrate and net GI alkali absorption increased, yielding a significantly positive correlation (r = 0.62, p < 0.0001), with the slope indistinguishable from that of normal subjects. Thus, urinary citrate was normally dependent on the net GI absorption of alkali. This dependence was less marked in RTA, confirming the renal origin of hypocitraturia. However, the normal dependence was maintained in CDS and in idiopathic hypocitraturia, suggesting that reduced citrate excretion was largely dietary in origin as a result of low net alkali absorption (from a probable relative deficiency of vegetables and fruits or a relative excess of animal proteins).

  20. Hydrothermal alkali metal recovery process

    DOEpatents

    Wolfs, Denise Y.; Clavenna, Le Roy R.; Eakman, James M.; Kalina, Theodore

    1980-01-01

    In a coal gasification operation or similar conversion process carried out in the presence of an alkali metal-containing catalyst wherein solid particles containing alkali metal residues are produced, alkali metal constituents are recovered from the particles by treating them with a calcium or magnesium-containing compound in the presence of water at a temperature between about 250.degree. F. and about 700.degree. F. and in the presence of an added base to establish a pH during the treatment step that is higher than would otherwise be possible without the addition of the base. During the treating process the relatively high pH facilitates the conversion of water-insoluble alkali metal compounds in the alkali metal residues into water-soluble alkali metal constituents. The resultant aqueous solution containing water-soluble alkali metal constituents is then separated from the residue solids, which consist of the treated particles and any insoluble materials formed during the treatment step, and recycled to the gasification process where the alkali metal constituents serve as at least a portion of the alkali metal constituents which comprise the alkali metal-containing catalyst. Preferably, the base that is added during the treatment step is an alkali metal hydroxide obtained by water washing the residue solids produced during the treatment step.

  1. Efficient destruction of CF4 through in situ generation of alkali metals from heated alkali halide reducing mixtures.

    PubMed

    Lee, Myung Churl; Choi, Wonyong

    2002-03-15

    Perfluorocarbons (PFCs) are the most potent green house gases that are very recalcitrant at destruction. An effective way of converting PFCs using hot solid reagents into safe products has been recently introduced. By investigating the thermal reductive destruction of tetrafluoromethane (CF4) we provided new insight and more physicochemical consideration on this novel process. The complete destruction of CF4was successfully achieved by flowing the gas through a heated reagent bed (400-950 degrees C) that contained powder mixtures of alkali halides, CaO, and Si. The silicon acted as a reducing agent of alkali halides for the in-situ production of alkali metals, and the calcium oxide played the role of a halide ion acceptor. The absence of any single component in this ternary mixture drastically reduced the destruction efficiency of CF4. The CF4 destruction efficiencies with the solid reagent containing the alkali halide, MX, increased in the order of Li approximately Na < K < Cs for alkali cations and I < Br < Cl < F for halide anions. This trend agreed with the endothermicity of the alkali metal generation reaction: the higher the endothermicity, the lower the destruction efficiency. Alkali metal generation was indirectly detected by monitoring H2 production from its reaction with water. The production of alkali metals increased with NaF, KF, and CsF in this order. The CsF/CaO/Si system exhibited the complete destruction of CF4 at as low as 600 degrees C. The solid product analysis by X-ray diffraction (XRD) showed the formation of CaF2 and the depletion of Si with black carbon particles formed in the solid reagent residue. No CO/CO2 and toxic HF and SiF4 formation were detected in the exhaust gas. PMID:11944694

  2. Simple model potential and model wave functions for (H-alkali)+ and (alkali-alkali)+ ions

    NASA Astrophysics Data System (ADS)

    Patil, S. H.; Tang, K. T.

    2000-07-01

    A simple model potential is proposed to describe the interaction of a valence electron with the alkali core, which incorporates the correct asymptotic behavior in terms of dipolar polarizabilities, and the short-range exchange effects in terms of a hard core adjusted to give the correct energy for the valence electron. Based on this potential, simple wave functions are developed to describe the (H-alkali)+ and (alkali-alkali)+ ions. These wave functions exhibit some important structures of the ions, and provide a universal description of the properties of all (H-alkali)+ and (alkali-alkali)+ ions, in particular, the equilibrium separations of the nuclei and the corresponding dissociation energies. They also allow us to calculate the dipolar polarizabilities of Li2+, Na2+, K2+, Rb2+, and Cs2+.

  3. Alkali-vapor lasers

    NASA Astrophysics Data System (ADS)

    Zweiback, J.; Komashko, A.; Krupke, W. F.

    2010-02-01

    We report on the results from several of our alkali laser systems. We show highly efficient performance from an alexandrite-pumped rubidium laser. Using a laser diode stack as a pump source, we demonstrate up to 145 W of average power from a CW system. We present a design for a transversely pumped demonstration system that will show all of the required laser physics for a high power system.

  4. The fate of minor alkali elements in the chemical evolution of salt lakes

    PubMed Central

    2011-01-01

    Alkaline earth elements and alkali metals (Mg, Ca, Na and K) play an important role in the geochemical evolution of saline lakes as the final brine type is defined by the abundance of these elements. The role of major ions in brine evolution has been studied in great detail, but little has been done to investigate the behaviour of minor alkali elements in these systems despite their similar chemical affinities to the major cations. We have examined three major anionic brine types, chloride, sulphate, and bicarbonate-carbonate, in fifteen lakes in North America and Antarctica to determine the geochemical behaviour of lithium, rubidium, strontium, and barium. Lithium and rubidium are largely conservative in all water types, and their concentrations are the result of long-term solute input and concentration through evaporation and/or sublimation. Strontium and barium behaviours vary with anionic brine type. Strontium can be removed in sulphate and carbonate-rich lakes by the precipitation of carbonate minerals. Barium may be removed in chloride and sulphate brines by either the precipitation of barite and perhaps biological uptake. PMID:21992434

  5. The fate of minor alkali elements in the chemical evolution of salt lakes.

    PubMed

    Witherow, Rebecca A; Lyons, W Berry

    2011-01-01

    Alkaline earth elements and alkali metals (Mg, Ca, Na and K) play an important role in the geochemical evolution of saline lakes as the final brine type is defined by the abundance of these elements. The role of major ions in brine evolution has been studied in great detail, but little has been done to investigate the behaviour of minor alkali elements in these systems despite their similar chemical affinities to the major cations. We have examined three major anionic brine types, chloride, sulphate, and bicarbonate-carbonate, in fifteen lakes in North America and Antarctica to determine the geochemical behaviour of lithium, rubidium, strontium, and barium. Lithium and rubidium are largely conservative in all water types, and their concentrations are the result of long-term solute input and concentration through evaporation and/or sublimation. Strontium and barium behaviours vary with anionic brine type. Strontium can be removed in sulphate and carbonate-rich lakes by the precipitation of carbonate minerals. Barium may be removed in chloride and sulphate brines by either the precipitation of barite and perhaps biological uptake. PMID:21992434

  6. (abstract) Experimental and Modeling Studies of the Exchange Current at the Alkali Beta'-Alumina/Porous Electrode/Alkali Metal Vapor Three Phase Boundary

    NASA Technical Reports Server (NTRS)

    Williams, R. M.; Jeffries-Nakamura, B.; Ryan, M. A.; Underwood, M. L.; O'Connor, D.; Kikkert, S.

    1993-01-01

    The microscopic mechanism of the alkali ion-electron recombination reaction at the three phase boundary zone formed by a porous metal electrode in the alkali vapor on the surface of an alkali beta'-alumina solid electrolyte (BASE) ceramic has been studied by comparison of the expected rates for the three simplest reaction mechanisms with known temperature dependent rate data; and the physical parameters of typical porous metal electrode/BASE/alkali metal vapor reaction zones. The three simplest reactions are tunneling of electrons from the alkali coated electrode to a surface bound alkali metal ion; emission of an electron from the electrode with subsequent capture by a surface bound alkali metal ion; and thermal emission of an alkali cation from the BASE and its capture on the porous metal electrode surface where it may recombine with an electron. Only the first reaction adequately accounts for both the high observed rate and its temperature dependence. New results include crude modeling of simple, one step, three phase, solid/solid/gas electrochemical reaction.

  7. Study of superconducting state parameters of alkali alkali binary alloys by a pseudopotential

    NASA Astrophysics Data System (ADS)

    Vora, Aditya M.

    2006-12-01

    A detailed study of the superconducting state parameters (SSP) viz. electron-phonon coupling strength λ, Coulomb pseudopotential μ∗, transition temperature TC, isotope effect exponent α and effective interaction strength N OV of ten alkali-alkali binary alloys i.e. Li 1- xNa x, Li 1- xK x, Li 1- xRb x, Li 1- xCs x, Na 1- xK x, Na 1- xRb x, Na 1- xCs x, K 1- xRb x, K 1- xCs x and Rb 1- xCs x are made within the framework of the model potential formalism and employing the pseudo-alloy-atom (PAA) model for the first time. We use the Ashcroft’s empty core (EMC) model potential for evaluating the superconducting properties of alkali alloys. Five different forms of local field correction functions viz. Hartree (H), Taylor (T), Ichimaru-Utsumi (IU), Farid et al. (F) and Sarkar et al. (S) are used to incorporate the exchange and correlation effects. A considerable influence of various exchange and correlation functions on λ and μ∗ is found from the present study. Reasonable agreement with the theoretical values of the SSP of pure components is found (corresponding to the concentration x = 0 or 1). It is also concluded that nature of the SSP strongly depends on the value of the atomic volume Ω0 of alkali-alkali binary alloys.

  8. Effects of Forest Succession on Exchangeable Cation Concentrations and Nitrogen Mineralization Rates in Soils Following Logging of Eastern Hemlock Forest, Whately, Massachusetts

    NASA Astrophysics Data System (ADS)

    Rhodes, A. L.; Sweezy, T.; Zukswert, J. M.; Dwyer, C. H.

    2012-12-01

    Ecological forest successions associated with invasive species and human disturbance may alter biogeochemical cycles within New England forests. Spread of the invasive insect hemlock woolly adelgid (Adelges tsugae) to eastern North America is causing mortality of the eastern hemlock (Tsuga canadensis), prompting salvage logging. Regrowth by deciduous hardwood trees is often observed. To evaluate whether changes in nutrient cycling could be altered by forest succession, we investigated exchangeable cation chemistry and nitrogen mineralization rates for soil in a mature, eastern hemlock forest and in a juvenile black birch (Betula lenta) forest in western MA. Eastern hemlock on this property was selectively logged 20 years ago, with black birch regrowth succeeding hemlock. We measured soil pH, exchangeable acidity (Al3+ and H+), exchangeable base cations (Ca2+, Mg2+, Na+, and K+), and nitrogen mineralization rates of organic and mineral horizons for 7 incubation periods between May 2011 - July 2012. We also measured the cation exchange capacity and nitrogen mineralization rates of soils from May - July 2012 (2 incubations) in a mature deciduous forest composed primarily of black birch. At each field site, 7 soil cores were collected. Soil horizons (organic and mineral) were separated and homogenized, and 3 replicates of each composite sample were analyzed for soil geochemistry. Organic soils within the juvenile black birch plot (BB) exhibit a low pH (4.3) similar to hemlock organic soils (HEM, pH=4.2). Surprisingly, exchangeable Al3+—the dominant cation in both plots—is significantly greater in organic soils at BB than at HEM (p<.001), and base saturation is less at BB (29%) than at HEM (46%, p<0.001) due to less Ca2+. There are no significant differences in the exchangeable cation chemistry of the mineral horizons at both sites, suggesting that the acidity difference of organic matter is not due to different soil mineralogy. In comparison, organic soil at the

  9. Impact of 1 mmol dm(-3) concentrations of small molecules containing nitrogen-based cationic groups on the oxygen reduction reaction on polycrystalline platinum in aqueous KOH (1 mol dm(-3)).

    PubMed

    Ong, Ai Lien; Whelligan, Daniel K; Fox, Michael L; Varcoe, John R

    2013-11-21

    Alkaline anion-exchange membranes (AAEMs) containing cationic head-groups (e.g. involving quaternary ammonium and imidazolium groups) are of interest with regard to application in alkaline polymer electrolyte fuel cells (APEFCs). This initial ex situ study evaluated the effect of 1 mmol dm(-3) concentrations of model molecules containing (AAEM-relevant) cationic groups on the oxygen reduction reaction on a polycrystalline platinum disk (Ptpc) electrode in aqueous KOH (1 mol dm(-3)). The cationic molecules studied were tetramethylammonium (TMA), benzyltrimethylammonium (BTMA), 1-benzyl-3-methylimidazolium (BMI), 1-benzyl-4-aza-1-azoniabicyclo[2.2.2]octane (BAABCO) and 6-(benzyloxy)-N,N,N-trimethylhexan-1-aminium (BOTMHA). Both cyclic and hydrodynamic linear sweep rotating disk electrode voltammetry techniques were used. The resulting voltammograms, derived estimates of apparent electrochemically active surface areas, Tafel slopes, apparent exchange-current densities and the number of electrons transferred (per O2 molecule) were compared. The results strongly suggest that 1 mmol dm(-3) concentrations of BTMA, BAABCO, and (especially) BMI seriously inhibit the catalytic activities of Ptpc in an aqueous KOH electrolyte at 25 °C. The negative influence of (benzene-ring-free) TMA and Cl(-) anions (KCl control experiment) appeared to be less severe. The separation of the trimethylammonium group from the benzene ring via a hexyloxy spacer chain (in BOTMHA) also produced a milder negative effect. PMID:24100347

  10. Molecular dispersion energy parameters for alkali and halide ions in aqueous solution.

    PubMed

    Reiser, S; Deublein, S; Vrabec, J; Hasse, H

    2014-01-28

    Thermodynamic properties of aqueous solutions containing alkali and halide ions are determined by molecular simulation. The following ions are studied: Li(+), Na(+), K(+), Rb(+), Cs(+), F(-), Cl(-), Br(-), and I(-). The employed ion force fields consist of one Lennard-Jones (LJ) site and one concentric point charge with a magnitude of ±1 e. The SPC/E model is used for water. The LJ size parameter of the ion models is taken from Deublein et al. [J. Chem. Phys. 136, 084501 (2012)], while the LJ energy parameter is determined in the present study based on experimental self-diffusion coefficient data of the alkali cations and the halide anions in aqueous solutions as well as the position of the first maximum of the radial distribution function of water around the ions. On the basis of these force field parameters, the electric conductivity, the hydration dynamics of water molecules around the ions, and the enthalpy of hydration is predicted. Considering a wide range of salinity, this study is conducted at temperatures of 293.15 and 298.15 K and a pressure of 1 bar. PMID:25669552

  11. Molecular dispersion energy parameters for alkali and halide ions in aqueous solution

    SciTech Connect

    Reiser, S.; Deublein, S.; Hasse, H.; Vrabec, J.

    2014-01-28

    Thermodynamic properties of aqueous solutions containing alkali and halide ions are determined by molecular simulation. The following ions are studied: Li{sup +}, Na{sup +}, K{sup +}, Rb{sup +}, Cs{sup +}, F{sup −}, Cl{sup −}, Br{sup −}, and I{sup −}. The employed ion force fields consist of one Lennard-Jones (LJ) site and one concentric point charge with a magnitude of ±1 e. The SPC/E model is used for water. The LJ size parameter of the ion models is taken from Deublein et al. [J. Chem. Phys. 136, 084501 (2012)], while the LJ energy parameter is determined in the present study based on experimental self-diffusion coefficient data of the alkali cations and the halide anions in aqueous solutions as well as the position of the first maximum of the radial distribution function of water around the ions. On the basis of these force field parameters, the electric conductivity, the hydration dynamics of water molecules around the ions, and the enthalpy of hydration is predicted. Considering a wide range of salinity, this study is conducted at temperatures of 293.15 and 298.15 K and a pressure of 1 bar.

  12. Use of Complementary Cation And Anion Heavy Atom-Atom Salt Derivatives to Solve the Structure of Cytochrome P450 46a1

    SciTech Connect

    White, M.A.; Mast, N.; Bjorkhem, I.; Johnson, E.F.; Stout, C.D.; Pikuleva, I.A.

    2009-05-26

    Human cytochrome P450 46A1 (CYP46A1) is one of the key enzymes in cholesterol homeostasis in the brain. The crystallization and heavy-atom structure solution of an active truncated CYP46A1 in complex with the high-affinity substrate analogue cholesterol-3-sulfate (CH-3S) is reported. The 2.6 {angstrom} structure of CYP46A1-CH-3S was solved using both anion and cation heavy-atom salts. In addition to the native anomalous signal from the haem iron, an NaI anion halide salt derivative and a complementary CsCl alkali-metal cation salt derivative were used. The general implications of the use of halide and alkali-metal quick soaks are discussed. The importance of using isoionic strength buffers, the titration of heavy-atom salts into different ionic species and the role of concentration are considered. It was observed that cation/anion-binding sites will occasionally overlap, which could negatively impact upon mixed RbBr soaks used for multiple anomalous scatterer MAD (MMAD). The use of complementary cation and anion heavy-atom salt derivatives is a convenient and powerful tool for MIR(AS) structure solution.

  13. Use of complementary cation and anion heavy-atom salt derivatives to solve the structure of cytochrome P450 46A1

    SciTech Connect

    White, Mark Andrew; Mast, Natalia; Bjorkhem, Ingemar; Johnson, Eric F.; Stout, C. David; Pikuleva, Irina A.

    2008-05-01

    Crystallization and analysis of the MIRAS heavy-atom structure solution of human cytochrome P450 46A1 using NaI and CsCl quick soaks. Human cytochrome P450 46A1 (CYP46A1) is one of the key enzymes in cholesterol homeostasis in the brain. The crystallization and heavy-atom structure solution of an active truncated CYP46A1 in complex with the high-affinity substrate analogue cholesterol-3-sulfate (CH-3S) is reported. The 2.6 Å structure of CYP46A1–CH-3S was solved using both anion and cation heavy-atom salts. In addition to the native anomalous signal from the haem iron, an NaI anion halide salt derivative and a complementary CsCl alkali-metal cation salt derivative were used. The general implications of the use of halide and alkali-metal quick soaks are discussed. The importance of using isoionic strength buffers, the titration of heavy-atom salts into different ionic species and the role of concentration are considered. It was observed that cation/anion-binding sites will occasionally overlap, which could negatively impact upon mixed RbBr soaks used for multiple anomalous scatterer MAD (MMAD). The use of complementary cation and anion heavy-atom salt derivatives is a convenient and powerful tool for MIR(AS) structure solution.

  14. PROCESS OF RECOVERING ALKALI METALS

    DOEpatents

    Wolkoff, J.

    1961-08-15

    A process is described of recovering alkali metal vapor by sorption on activated alumina, activated carbon, dehydrated zeolite, activated magnesia, or Fuller's earth preheated above the vaporization temperature of the alkali metal and subsequent desorption by heating the solvent under vacuum. (AEC)

  15. Preparation of alkali metal dispersions

    NASA Technical Reports Server (NTRS)

    Rembaum, A.; Landel, R. F. (Inventor)

    1968-01-01

    A method is described for producing alkali metal dispersions of high purity. The dispersions are prepared by varying the equilibrium solubility of the alkali metal in a suitable organic solvent in the presence of aromatic hydrocarbons. The equilibrium variation is produced by temperature change. The size of the particles is controlled by controlling the rate of temperature change.

  16. Stable synthetic mono-substituted cationic bacteriochlorins mediate selective broad-spectrum photoinactivation of drug-resistant pathogens at nanomolar concentrations

    PubMed Central

    Huang, Liyi; Krayer, Michael; Roubil, John G. S.; Huang, Ying-Ying; Holten, Dewey; Lindsey, Jonathan S.; Hamblin, Michael R.

    2014-01-01

    A set of three stable synthetic mono-substituted cationic bacteriochlorins (BC37, BC38 and BC39) were recently reported to show exceptional activity (low nanomolar) in mediating photodynamic killing of human cancer cells after a 24 h incubation upon excitation with near-infrared light (730 nm). The presence of cationic quaternary ammonium groups in each compound suggested likely activity as antimicrobial photosensitizers. Herein this hypothesis was tested against a panel of pathogenic microorganisms that have all recently drawn attention due to increased drug-resistance (Gram-positive bacteria, Staphylococcus aureus and Enterococcus faecalis; Gram-negative bacteria, Escherichia coli and Acinetobacter baumannii; and fungal yeasts Candida albicans and Cryptococcus neoformans). All three bacteriochlorins were highly effective against both Gram-positive species (> 6 logs of eradication at ≤ 200 nM and 10 J/cm2). The dicationic bacteriochlorin (BC38) was best against the Gram-negative species (> 6 logs at 1–2 μM) and the lipophilic monocationic bacteriochlorin (BC39) was best against the fungi (> 6 logs at 1 μM). The bacteriochlorins produced substantial singlet oxygen (and apparently less Type-1 reactive-oxygen species such as hydroxyl radical) as judged by activation of fluorescent probes and comparison with 1H-phenalen-1-one-2-sulfonic acid; the order of activity was BC37 > BC38 > BC39. A short incubation time (30 min) resulted in selectivity for microbial cells over HeLa human cells. The highly active photodynamic inactivation of microbial cells may stem from the amphiphilic and cationic features of the bacteriochlorins. PMID:25463659

  17. Combined cation-exchange and extraction chromatographic method of pre-concentration and concomitant separation of Cu(II) with high molecular mass liquid cation exchanger after its online detection.

    PubMed

    Mandal, B; Roy, U S; Datta, D; Ghosh, N

    2011-08-19

    A selective method has been developed for the extraction chromatographic trace level separation of Cu(II) with Versatic 10 (liquid cation exchanger) coated on silanised silica gel (SSG-V10). Cu(II) has been extracted from 0.1M acetate buffer at the range of pH 4.0-5.5. The effects of foreign ions, pH, flow-rate, stripping agents on extraction and elution have been investigated. Exchange capacity of the prepared exchanger at different temperatures with respect to Cu(II) has been determined. The extraction equilibrium constant (K(ex)) and different standard thermodynamic parameters have also been calculated by temperature variation method. Positive value of ΔH (7.98 kJ mol⁻¹) and ΔS (0.1916 kJ mol⁻¹) and negative value of ΔG (-49.16 kJ mol⁻¹) indicated that the process was endothermic, entropy gaining and spontaneous. Preconcentration factor was optimized at 74.7 ± 0.2 and the desorption constants K(desorption)¹(1.4 × 10⁻²) and K(desorption)²(9.8 × 10⁻²) were determined. The effect of pH on R(f) values in ion exchange paper chromatography has been investigated. In order to investigate the sorption isotherm, two equilibrium models, the Freundlich and Langmuir isotherms, were analyzed. Cu(II) has been separated from synthetic binary and multi-component mixtures containing various metal ions associated with it in ores and alloy samples. The method effectively permits sequential separation of Cu(II) from synthetic quaternary mixture containing its congeners Bi(III), Sn(II), Hg(II) and Cu(II), Cd(II), Pb(II) of same analytical group. The method was found effective for the selective detection, removal and recovery of Cu(II) from industrial waste and standard alloy samples following its preconcentration on the column. A plausible mechanism for the extraction of Cu(II) has been suggested. PMID:21764063

  18. Use of laser induced photoacoustic spectroscopy (LIPAS) to determine equilibrium constants of cation-cation complexes

    SciTech Connect

    Hannink, N.J.; Hoffman, D.C.; Silva, R.J.; Russo, R.E.

    1993-12-31

    Laser Induced PhotoAcoustic Spectroscopy (LIPAS) is a relatively new, photothermal technique to examine solutions. Studies in the past have shown it to be more sensitive than conventional absorption spectroscopy, while, yielding the same information thus allowing lower concentrations to be used. This study is using LIPAS to examine solutions to determine the equilibrium constants of cation-cation complexes. It has been found that actinyl(V) cations form cation-cation complexes with a variety of cations, including actinyl(VI) cations. The radioactive nature of the actinide elements requires special handling techniques and also require limits be placed on the amount of material that can be used. The sensitivity of some oxidation states of the actinides to oxygen also presents a problem. Preliminary results will be presented for actinyl(V)-actinyl(VI) cation-cation complexes that were studied using a remote LIPAS system incorporating fiber optics for transmission of laser signals.

  19. Alkali metal and alkali earth metal gadolinium halide scintillators

    DOEpatents

    Bourret-Courchesne, Edith; Derenzo, Stephen E.; Parms, Shameka; Porter-Chapman, Yetta D.; Wiggins, Latoria K.

    2016-08-02

    The present invention provides for a composition comprising an inorganic scintillator comprising a gadolinium halide, optionally cerium-doped, having the formula A.sub.nGdX.sub.m:Ce; wherein A is nothing, an alkali metal, such as Li or Na, or an alkali earth metal, such as Ba; X is F, Br, Cl, or I; n is an integer from 1 to 2; m is an integer from 4 to 7; and the molar percent of cerium is 0% to 100%. The gadolinium halides or alkali earth metal gadolinium halides are scintillators and produce a bright luminescence upon irradiation by a suitable radiation.

  20. Cation effects on interfacial water organization of aqueous chloride solutions. I. Monovalent cations: Li+, Na+, K+, and NH4(+).

    PubMed

    Hua, Wei; Verreault, Dominique; Huang, Zishuai; Adams, Ellen M; Allen, Heather C

    2014-07-17

    The influence of monovalent cations on the interfacial water organization of alkali (LiCl, NaCl, and KCl) and ammonium chloride (NH4Cl) salt solutions was investigated using surface-sensitive conventional vibrational sum frequency generation (VSFG) and heterodyne-detected (HD-)VSFG spectroscopy. It was found in the conventional VSFG spectra that LiCl and NH4Cl significantly perturb water’s hydrogen-bonding network. In contrast, NaCl and KCl had little effect on the interfacial water structure and exhibited weak concentration dependency. The Im χs(2)(ωIR) spectra from HD-VSFG further revealed that, for all chloride solutions, the net transition dipole moments of hydrogen-bonded water molecules (O → H) are oriented more toward the vapor phase relative to neat water. This suggests the presence of an interfacial electric field generated from the formation of an ionic double layer in the interfacial region with a distribution of Cl(-) ions located above the countercations, in agreement with predictions from MD simulations. The magnitude of this electric field shows a small but definite cation specificity and follows the order Li(+) ≈ Na(+) > NH4(+) > K(+). The observed trend was found to be in good agreement with previously published surface potential data. PMID:24798506

  1. Alkali Activated Systems: Understanding the Influence of Curing Conditions and Activator Type/Chemistry on the Mechanical Strength and Chemical Structure of Fly Ash/Slag Systems

    NASA Astrophysics Data System (ADS)

    Chowdhury, Ussala

    The alkali activation of aluminosilicate materials as binder systems derived from industrial byproducts have been extensively studied due to the advantages they offer in terms enhanced material properties, while increasing sustainability by the reuse of industrial waste and byproducts and reducing the adverse impacts of OPC production. Fly ash and ground granulated blast furnace slag are commonly used for their content of soluble silica and aluminate species that can undergo dissolution, polymerization with the alkali, condensation on particle surfaces and solidification. The following topics are the focus of this thesis: (i) the use of microwave assisted thermal processing, in addition to heat-curing as a means of alkali activation and (ii) the relative effects of alkali cations (K or Na) in the activator (powder activators) on the mechanical properties and chemical structure of these systems. Unsuitable curing conditions instigate carbonation, which in turn lowers the pH of the system causing significant reductions in the rate of fly ash activation and mechanical strength development. This study explores the effects of sealing the samples during the curing process, which effectively traps the free water in the system, and allows for increased aluminosilicate activation. The use of microwave-curing in lieu of thermal-curing is also studied in order to reduce energy consumption and for its ability to provide fast volumetric heating. Potassium-based powder activators dry blended into the slag binder system is shown to be effective in obtaining very high compressive strengths under moist curing conditions (greater than 70 MPa), whereas sodium-based powder activation is much weaker (around 25 MPa). Compressive strength decreases when fly ash is introduced into the system. Isothermal calorimetry is used to evaluate the early hydration process, and to understand the reaction kinetics of the alkali powder activated systems. A qualitative evidence of the alkali

  2. Structural implications of water dissolution in haplogranitic glasses from NMR spectroscopy: influence of total water content and mixed alkali effect

    NASA Astrophysics Data System (ADS)

    Schmidt, B. C.; Riemer, T.; Kohn, S. C.; Holtz, F.; Dupree, R.

    2001-09-01

    To study the effects of total water content and alkali substitution on the structure of aluminosilicate glasses, two series of glasses belonging to the ternary system Quartz (Qz)-Albite (Ab)-Orthoclase (Or) were synthesized and investigated with nuclear magnetic resonance (NMR) spectroscopy. Series I consisted of seven glasses with normative composition Ab 39Or 32Qz 29 (AOQ) and water contents ranging from 0 to 6 wt%. Series II consisted of dry and hydrous glasses (˜2.0 wt% H 2O) with five compositions along the join Qz 37Ab 63-Qz 34Or 66 (AQ-OQ) varying the alkali content (Na/K) at constant Si/Al ratio. All glasses were investigated with 1H, 23Na, 27Al and 29Si magic angle spinning (MAS) NMR. 29Si MAS spectra of AOQ glasses showed no change upon hydration, suggesting little variation of the Si environments although the large linewidth of the 29Si signal may hide the presence of some Si Q 3-OH. The isotropic chemical shift (δ iso) of 27Al showed no change upon hydration, regardless of the amount of dissolved water. The 27Al mean quadrupolar coupling constant (C q) decreased with increasing water content, indicating a general increase of symmetry of the charge distribution around Al, which suggests the absence of significant amounts of Al Q 3-OH. Nonetheless, the evolution of C q upon hydration suggests a correlation with OH concentration in the quenched glass. The evolution of 23Na isotropic chemical shifts upon hydration appears to be correlated with total water content or with the concentration of dissolved H 2O molecules. In general, the NMR data are consistent with the water solubility model of Kohn et al. (1989), involving the exchange of charge balancing cations by protons. However, in addition to the presence of molecular water, 1H-NMR results showed at least two types of OH groups of which one may be related to Al-OH. Although the small intensity of this signal indicates that only a minor fraction of OH groups is present in this species, it demonstrates

  3. Macroscopic and bulk-controlled elastic modes in an interaction of interstitial alcali metal cations within a face-centered cubic crystalline fullerine

    NASA Technical Reports Server (NTRS)

    Tatarenko, Valentine A.; Tsysman, Constantin L.; Oltarzhevskaya, Yelena T.

    1995-01-01

    The calculations in a majority of previous works for the fulleride (AqC-60) crystals were performed within the framework of the rigid-lattice model, neglecting the distortion relaxation of the host fullerene (C-60) crystal caused by the interstitial alkali-metal (A) cations. However, an each cation is a source of a static distortion field, and the resulting field is a superposition of such fields generated by all cations. This is a reason why the host-crystal distortions depend on the A-cations configurations, i.e. on a type of a spatial bulk distribution of interstitial cations. The given paper seeks to find a functional relation between the amplitudes of the doping-induced structure-distortion waves and of static concentration ones. A semiphenomenological model is constructed here within the scope of statistical-thermodynamic treatment and using the lattice-statistics simulation method(*). In this model the effects due to the presence of q solute A cations over available interstices (per unit cell) on the static inherent reorientation and/or displacements of the solvent molecules from the 'average-lattice' sites' as well as on the lattice parameter a of a elastically-anysotropic 'cubic' C-60 crystal are taken into account.

  4. Macroscopic and bulk-controlled elastic modes in an interaction of interstitial alcali metal cations within a face-centered cubic crystalline fullerine

    SciTech Connect

    Tatarenko, V.A.; Tsysman, C.L.; Oltarzhevskaya, Y.T.

    1994-12-31

    The calculations in a majority of previous works for the fulleride (AqC{sub 60}) crystals were performed within the framework of the rigid-lattice model, neglecting the distoration relaxation of the host fullerene (C{sub 60}) crystal caused by the interstitial alkali-metal (A) cations. However, an each cation is a source of a static distoration field, and the resulting field is a superposition of such fields generated by all cations. This is a reason why the host-crystal distortions depend on the A-cations configurations, i.e. on a type of a spatial bulk distribution of interstitial cations. This paper seeks to find a functional relation between the amplitudes of the doping-induced structure-distortion waves and of statistic concentration ones. A semiphenomenological model is constructed here within the scope of statistical-thermodynamic treatment and using the lattice-statistics simulation method. In this model the effects due to the presence of q solute A cations over available interstices (per unit cell) on the statistic inherent reorientation and/or displacements of the solvent molecules from the average-lattice sites as well as on the lattice parameter a of the elastically-anysotropic cubic C{sub 60} crystal are taken into account.

  5. Upgrading platform using alkali metals

    SciTech Connect

    Gordon, John Howard

    2014-09-09

    A process for removing sulfur, nitrogen or metals from an oil feedstock (such as heavy oil, bitumen, shale oil, etc.) The method involves reacting the oil feedstock with an alkali metal and a radical capping substance. The alkali metal reacts with the metal, sulfur or nitrogen content to form one or more inorganic products and the radical capping substance reacts with the carbon and hydrogen content to form a hydrocarbon phase. The inorganic products may then be separated out from the hydrocarbon phase.

  6. Is Electronegativity a Useful Descriptor for the "Pseudo-Alkali-Metal" NH4?

    SciTech Connect

    Whiteside, Alexander; Xantheas, Sotiris S.; Gutowski, Maciej S.

    2011-11-18

    Molecular ions in the form of "pseudo-atoms" are common structural motifs in chemistry, with properties that are transferrable between different compounds. We have determined the electronegativity of the "pseudo-alkali metal" ammonium (NH4) and evaluated its reliability as a descriptor in comparison to the electronegativities of the alkali metals. The computed properties of its binary complexes with astatine and of selected borohydrides confirm the similarity of NH4 to the alkali metal atoms, although the electronegativity of NH4 is relatively large in comparison to its cationic radius. We paid particular attention to the molecular properties of ammonium (angular anisotropy, geometric relaxation, and reactivity), which can cause deviations from the behaviour expected of a conceptual "true alkali metal" with this electronegativity. These deviations allow for the discrimination of effects associated with the polyatomic nature of NH4.

  7. Is electronegativity a useful descriptor for the pseudo-alkali metal NH4?

    PubMed

    Whiteside, Alexander; Xantheas, Sotiris S; Gutowski, Maciej

    2011-11-18

    Molecular ions in the form of "pseudo-atoms" are common structural motifs in chemistry, with properties that are transferrable between different compounds. We have determined one such property--the electronegativity--for the "pseudo-alkali metal" ammonium (NH(4)), and evaluated its reliability as a descriptor versus the electronegativities of the alkali metals. The computed properties of ammonium's binary complexes with astatine and of selected borohydrides confirm the similarity of NH(4) to the alkali metal atoms, although the electronegativity of NH(4) is relatively large in comparison to its cationic radius. We have paid particular attention to the molecular properties of ammonium (angular anisotropy, geometric relaxation and reactivity), which can cause deviations from the behaviour expected of a conceptual "true alkali metal" with this electronegativity. These deviations allow for the discrimination of effects associated with the molecular nature of NH(4). PMID:21928287

  8. Pretreatment of garden biomass by alkali-assisted ultrasonication: effects on enzymatic hydrolysis and ultrastructural changes

    PubMed Central

    2014-01-01

    The present investigation aims at studying the effectiveness of alkali-assisted ultrasonication on pretreatment of garden biomass (GB). Dry and powdered GB suspended in 1% NaOH was ultrasonicated for 15, 30 and 60 minutes at a frequency of 25 KHZ. The mode of action and effectiveness of alkali-assisted ultrasonication on GB was established through microscopic, scanning electron microscopic and X-ray diffraction studies. A perusal of results showed that alkali-assisted ultrasonication led to fibrillation of GB which ultimately facilitated enzymatic hydrolysis. The results also indicated that alkali-assisted ultrasonication is an efficient means of pretreatment of GB at moderate (45-50°C) working temperature and low (1%) concentration of alkali. The yield of reducing sugar after enzymatic hydrolysis increased almost six times as compared to control due to alkali-assisted ultrasonication. PMID:24843790

  9. Reduction in the concentration of cation vacancies by proper Si-doping in the well layers of high AlN mole fraction AlxGa1-xN multiple quantum wells grown by metalorganic vapor phase epitaxy

    NASA Astrophysics Data System (ADS)

    Chichibu, S. F.; Miyake, H.; Ishikawa, Y.; Furusawa, K.; Hiramatsu, K.

    2015-09-01

    Appropriate-amount Si-doping in the well layers significantly improved the luminescence efficiency of Al0.68Ga0.32N/Al0.77Ga0.23N multiple quantum wells. To understand the mechanisms, spatio-time-resolved cathodoluminescence measurements and self-consistent Schrödinger-Poisson calculations were carried out. The increase in the luminescence lifetime at room temperature, which reflects the decrease in the concentration of nonradiative recombination centers (NRCs), was correlated with increased terrace width of Si-doped wells. The results suggest the importance of H3SiNH2 doping-reactant formation that gives rise to enhanced decomposition of NH3 and provides wetting conditions by surface Si-N bonds, which reduce the total energy and concentration of NRCs composed of cation vacancies.

  10. Coordination effect-regulated CO2 capture with an alkali metal onium salts/crown ether system

    SciTech Connect

    Yang, Zhen-Zhen; Jiang, Deen; Zhu, Xiang; Tian, Chengcheng; Brown, Suree; Do-Thanh, Chi-Linh; He, Liang-Nian; Dai, Sheng

    2014-01-01

    A coordination effect was employed to realize equimolar CO2 absorption, adopting easily synthesized amino group containing absorbents (alkali metal onium salts). The essence of our strategy was to increase the steric hindrance of cations so as to enhance a carbamic acid pathway for CO2 capture. Our easily synthesized alkali metal amino acid salts or phenolates were coordinated with crown ethers, in which highly sterically hindered cations were obtained through a strong coordination effect of crown ethers with alkali metal cations. For example, a CO2 capacity of 0.99 was attained by potassium prolinate/18-crown-6, being characterized by NMR, FT-IR, and quantum chemistry calculations to go through a carbamic acid formation pathway. The captured CO2 can be stripped under very mild conditions (50 degrees C, N-2). Thus, this protocol offers an alternative for the development of technological innovation towards efficient and low energy processes for carbon capture and sequestration.

  11. Thermodynamics of Liquid Alkali Metals and Their Binary Alloys

    NASA Astrophysics Data System (ADS)

    Thakor, P. B.; Patel, Minal H.; Gajjar, P. N.; Jani, A. R.

    2009-07-01

    The theoretical investigation of thermodynamic properties like internal energy, entropy, Helmholtz free energy, heat of mixing (ΔE) and entropy of mixing (ΔS) of liquid alkali metals and their binary alloys are reported in the present paper. The effect of concentration on the thermodynamic properties of Ac1Bc2 alloy of the alkali-alkali elements is investigated and reported for the first time using our well established local pseudopotential. To investigate influence of exchange and correlation effects, we have used five different local field correction functions viz; Hartree(H), Taylor(T), Ichimaru and Utsumi(IU), Farid et al. (F) and Sarkar et al. (S). The increase of concentration C2, increases the internal energy and Helmholtz free energy of liquid alloy Ac1Bc2. The behavior of present computation is not showing any abnormality in the outcome and hence confirms the applicability of our model potential in explaining the thermodynamics of liquid binary alloys.

  12. Crown-Ether Derived Graphene Hybrid Composite for Membrane-Free Potentiometric Sensing of Alkali Metal Ions.

    PubMed

    Olsen, Gunnar; Ulstrup, Jens; Chi, Qijin

    2016-01-13

    We report the design and synthesis of newly functionalized graphene hybrid material that can be used for selective membrane-free potentiometric detection of alkali metal ions, represented by potassium ions. Reduced graphene oxide (RGO) functionalized covalently by 18-crown[6] ether with a dense surface coverage is achieved by the introduction of a flexible linking molecule. The resulting hybrid composite is highly stable and is capable of detecting potassium ions down to micromolar ranges with a selectivity over other cations (including Ca(2+), Li(+), Na(+), NH4(+)) at concentrations up to 25 mM. This material can be combined further with disposable chips, demonstrating its promise as an effective ion-selective sensing component for practical applications. PMID:26703780

  13. First-principles study of ternary graphite compounds cointercalated with alkali atoms (Li, Na, and K) and alkylamines towards alkali ion battery applications

    NASA Astrophysics Data System (ADS)

    Ri, Gum-Chol; Yu, Chol-Jun; Kim, Jin-Song; Hong, Song-Nam; Jong, Un-Gi; Ri, Mun-Hyok

    2016-08-01

    First-principles calculations were carried out to investigate the structural, energetic, and electronic properties of ternary graphite compounds cointercalated with alkali atoms (AM = Li, Na, and K) and normal alkylamine molecules (nCx; x = 1, 2, 3, 4), denoted as AM-nCx-GICs. From the optimization of the orthorhombic unit cells for the crystalline compounds, it was found that, with the increase in the atomic number of alkali atoms, the layer separations decrease in contrast to AM-GICs, while the bond lengths between alkali atoms and graphene layer, and nitrogen atom of alkylamine increase. The calculated formation energies and interlayer binding energies of AM-nC3-GICs indicate that the compounds is increasingly stabilized from Li to K, and the energy barriers for migration of alkali atoms suggest that alkali cation with larger ionic radius diffuses more smoothly in graphite, being similar to AM-GICs. Through the analysis of electronic properties, it was established that more extent of electronic charge is transferred from more electropositive alkali atom to the carbon ring of graphene layer, and the hybridization of valence electron orbitals between alkylamine molecules and graphene layer is occurred.

  14. Intermetallic Competition in the Fragmentation of Trimetallic Au-Zn-Alkali Complexes.

    PubMed

    Lang, Johannes; Cayir, Merve; Walg, Simon P; Di Martino-Fumo, Patrick; Thiel, Werner R; Niedner-Schatteburg, Gereon

    2016-02-12

    Cationization is a valuable tool to enable mass spectrometric studies on neutral transition-metal complexes (e.g., homogenous catalysts). However, knowledge of potential impacts on the molecular structure and catalytic reactivity induced by the cationization is indispensable to extract information about the neutral complex. In this study, we cationize a bimetallic complex [AuZnCl3 ] with alkali metal ions (M(+) ) and investigate the charged adducts [AuZnCl3 M](+) by electrospray ionization mass spectrometry (ESI-MS). Infrared multiple photon dissociation (IR-MPD) in combination with density functional theory (DFT) calculations reveal a μ(3) binding motif of all alkali ions to the three chlorido ligands. The cationization induces a reorientation of the organic backbone. Collision-induced dissociation (CID) studies reveal switches of fragmentation channels by the alkali ion and by the CID amplitude. The Li(+) and Na(+) adducts prefer the sole loss of ZnCl2 , whereas the K(+) , Rb(+) , and Cs(+) adducts preferably split off MCl2 ZnCl. Calculated energetics along the fragmentation coordinate profiles allow us to interpret the experimental findings to a level of subtle details. The Zn(2+) cation wins the competition for the nitrogen coordination sites against K(+) , Rb(+) , and Cs(+) , but it loses against Li(+) and Na(+) in a remarkable deviation from a naive hard and soft acids and bases (HSAB) concept. The computations indicate expulsion of MCl2 ZnCl rather than of MCl and ZnCl2 . PMID:26785330

  15. Simultaneous high-temperature removal of alkali and particulates in a pressurized gasification system. Fifth quarterly project report, April 1982-June 1982. [Concentration of Na and K in gas at process conditions; also optimization of removal system

    SciTech Connect

    Mulik, P.R.; Alvin, M.A.; Bachovchin, D.M.

    1982-07-01

    This program is directed at performing experimental and analytical investigations, deriving system designs, and estimating costs to ascertain the feasibility of using aluminosilicate-based getters for controlling alkali in pressurized gasification systems. Its overall objective is to develop a comprehensive plan for evaluating a scaled-up version of the gettering process as a unit operation or as an integral part of a particulate removal device. This report briefly summarizes efforts previously completed on thermodynamic projections and system performance projections, together with current work on getter selection and qualification completed during the fifth quarter of the project. Work on the thermodynamic projections has been completed and includes an update of the data base, development of alkali phase diagrams, and projections for several gasification processes. Getter selection and qualification efforts involved four tests - two with activated bauxite and one each with diatomaceous earth and Novacite on the thermogravimetric analysis (TGA) system. Finally, system performance projections entailed examination of available kinetic data to ascertain the rate-controlling step, along with modeling efforts to determine the size requirements of a commercial-sized unit.

  16. A new mechanism for radiation damage processes in alkali halides

    NASA Astrophysics Data System (ADS)

    Dubinko, V. I.; Turkin, A. A.; Vainshtein, D. I.; den Hartog, H. W.

    1999-12-01

    We present a theory of radiation damage formation in alkali halides based on a new mechanism of dislocation climb, which involves the production of VF centers (self-trapped hole neighboring a cation vacancy) as a result of the absorption of H centers of dislocation lines. We consider the evolution of all experimentally observed extended defects: metal colloids, gas bubbles, and vacancy voids. Voids are shown to arise and grow large due to the reaction between F and VF centers at the surface of halogen bubbles. Voids can ignite a back reaction between the radiolytic products resulting in decomposition of the irradiated material.

  17. Concentrations and environmental fate of Ra in cation-exchange regeneration brine waste disposed to septic tanks and accumulation in sludge, New Jersey Coastal Plain, USA

    USGS Publications Warehouse

    Szabo, Z.; Jacobsen, E.; Kraemer, T.F.; Parsa, B.

    2008-01-01

    Concentrations of Ra in liquid and solid wastes generated from 15 softeners treating domestic well waters from New Jersey Coastal Plain aquifers (where combined Ra (226Ra plus 228Ra) concentrations commonly exceed 0.185 Bq L-1) were determined. Softeners, when maintained, reduced combined Ra about 10-fold (<0.024 Bq L-1). Combined Ra exceeded 0.185 Bq L-1 at 1 non-maintained system. Combined Ra was enriched in regeneration brine waste (maximum, 81.2 Bq L-1), but concentrations in septic-tank effluents receiving brine waste were less than in the untreated ground waters. The maximum combined Ra concentration in aquifer sands (40.7 Bq kg-1 dry weight) was less than that in sludge from the septic tanks (range, 84-363 Bq kg-1), indicating Ra accumulation in sludge from effluent. The combined Ra concentration in sludge from the homeowners' septic systems falls within the range reported for sludge samples from publicly owned treatment works within the region.

  18. Improving the Photoluminescence Properties of Perovskite CH3NH3PbBr3-xClx Films by Modulating Organic Cation and Chlorine Concentrations.

    PubMed

    Yan, Jun; Zhang, Bing; Chen, Yunlin; Zhang, Ao; Ke, Xiaohan

    2016-05-25

    The photoluminescence (PL) properties of inorganic-organic perovskites can be drastically changed by tuning the halogen composition, especially the Cl content. However, our research demonstrated that in addition to the influence of Cl concentration, the PL emission intensity of CH3NH3PbBr3 strongly depends on the content of CH3NH3Br in the coating solution. The effects of CH3NH3Br and Cl concentrations on the PL properties of CH3NH3PbBr3-xClx were investigated. We found that a strong PL emission intensity of CH3NH3PbBr3 can be obtained from solutions with a high CH3NH3Br concentration. The PL emission intensities of CH3NH3PbBr3-xClx films were enhanced by adjusting the molar ratio of PbBr to PbCl2 only in a highly concentrated CH3NH3Br environment. Moreover, it was found that an optimum CH3NH3Br/PbBr2/PbCl2 ratio in the precursor solutions can be used to obtain the strongest PL emission intensity of CH3NH3PbBr3-xClx films. Further studies revealed that both CH3NH3Br and Cl concentrations significantly influence the CH3NH3PbBr3-xClx films evolution, which affects their PL properties. PMID:27163386

  19. Competitive interaction of monovalent cations with DNA from 3D-RISM.

    PubMed

    Giambaşu, George M; Gebala, Magdalena K; Panteva, Maria T; Luchko, Tyler; Case, David A; York, Darrin M

    2015-09-30

    The composition of the ion atmosphere surrounding nucleic acids affects their folding, condensation and binding to other molecules. It is thus of fundamental importance to gain predictive insight into the formation of the ion atmosphere and thermodynamic consequences when varying ionic conditions. An early step toward this goal is to benchmark computational models against quantitative experimental measurements. Herein, we test the ability of the three dimensional reference interaction site model (3D-RISM) to reproduce preferential interaction parameters determined from ion counting (IC) experiments for mixed alkali chlorides and dsDNA. Calculations agree well with experiment with slight deviations for salt concentrations >200 mM and capture the observed trend where the extent of cation accumulation around the DNA varies inversely with its ionic size. Ion distributions indicate that the smaller, more competitive cations accumulate to a greater extent near the phosphoryl groups, penetrating deeper into the grooves. In accord with experiment, calculated IC profiles do not vary with sequence, although the predicted ion distributions in the grooves are sequence and ion size dependent. Calculations on other nucleic acid conformations predict that the variation in linear charge density has a minor effect on the extent of cation competition. PMID:26304542

  20. Competitive interaction of monovalent cations with DNA from 3D-RISM

    PubMed Central

    Giambaşu, George M.; Gebala, Magdalena K.; Panteva, Maria T.; Luchko, Tyler; Case, David A.; York, Darrin M.

    2015-01-01

    The composition of the ion atmosphere surrounding nucleic acids affects their folding, condensation and binding to other molecules. It is thus of fundamental importance to gain predictive insight into the formation of the ion atmosphere and thermodynamic consequences when varying ionic conditions. An early step toward this goal is to benchmark computational models against quantitative experimental measurements. Herein, we test the ability of the three dimensional reference interaction site model (3D-RISM) to reproduce preferential interaction parameters determined from ion counting (IC) experiments for mixed alkali chlorides and dsDNA. Calculations agree well with experiment with slight deviations for salt concentrations >200 mM and capture the observed trend where the extent of cation accumulation around the DNA varies inversely with its ionic size. Ion distributions indicate that the smaller, more competitive cations accumulate to a greater extent near the phosphoryl groups, penetrating deeper into the grooves. In accord with experiment, calculated IC profiles do not vary with sequence, although the predicted ion distributions in the grooves are sequence and ion size dependent. Calculations on other nucleic acid conformations predict that the variation in linear charge density has a minor effect on the extent of cation competition. PMID:26304542

  1. High-temperature interactions of alkali vapors with solids during coal combustion and gasification

    SciTech Connect

    Punjak, W.A.

    1988-01-01

    A temperature and concentration programmed reaction method is used to investigate the mechanism by which organically bound alkali is released from carbonaceous substrates. Vaporization of the alkali is preceded by reduction of oxygen-bearing groups during which CO is generated. A residual amount of alkali remains after complete reduction. This residual level is greater for potassium, indicating that potassium has stronger interactions with graphitic substrates that sodium. Other mineral substrates were exposed to high temperature alkali chloride vapors under both nitrogen and simulated flue gas atmospheres to investigate their potential application as sorbents for the removal of alkali from coal conversion flue gases. The compounds containing alumina and silica are found to readily adsorb alkali vapors and the minerals kaolinite, bauxite and emathlite are identified as promising alkali sorbents. The fundamentals of alkali adsorption on kaolinite, bauxite and emathlite are compared and analyzed both experimentally and through theoretical modeling. The experiments were performed in a microgravimetric reactor system; the sorbents were characterized before and after alkali adsorption using scanning Auger microscopy, X-ray diffraction analysis, mercury porosimetry and atomic emission spectrophotometry. The results show that the process is not a simple physical condensation, but a complex combination of several diffusion steps and reactions.

  2. Influence of temperature on alkali stress adaptation in Listeria monocytogenes

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Listeria monocytogenes cells may induce alkali stress adaptation when exposed to sublethal concentrations of alkaline cleaners and sanitizers that may be frequently used in the food processing environment. In the present study, the effect of temperature on the induction and the stability of such alk...

  3. Cation specific binding with protein surface charges.

    PubMed

    Hess, Berk; van der Vegt, Nico F A

    2009-08-11

    Biological organization depends on a sensitive balance of noncovalent interactions, in particular also those involving interactions between ions. Ion-pairing is qualitatively described by the law of "matching water affinities." This law predicts that cations and anions (with equal valence) form stable contact ion pairs if their sizes match. We show that this simple physical model fails to describe the interaction of cations with (molecular) anions of weak carboxylic acids, which are present on the surfaces of many intra- and extracellular proteins. We performed molecular simulations with quantitatively accurate models and observed that the order K(+) < Na(+) < Li(+) of increasing binding affinity with carboxylate ions is caused by a stronger preference for forming weak solvent-shared ion pairs. The relative insignificance of contact pair interactions with protein surfaces indicates that thermodynamic stability and interactions between proteins in alkali salt solutions is governed by interactions mediated through hydration water molecules. PMID:19666545

  4. Hydrothermal alkali metal catalyst recovery process

    DOEpatents

    Eakman, James M.; Clavenna, LeRoy R.

    1979-01-01

    In a coal gasification operation or similar conversion process carried out in the presence of an alkali metal-containing catalyst wherein solid particles containing alkali metal residues are produced, alkali metal constituents are recovered from the particles primarily in the form of water soluble alkali metal formates by treating the particles with a calcium or magnesium-containing compound in the presence of water at a temperature between about 250.degree. F. and about 700.degree. F. and in the presence of added carbon monoxide. During the treating process the water insoluble alkali metal compounds comprising the insoluble alkali metal residues are converted into water soluble alkali metal formates. The resultant aqueous solution containing water soluble alkali metal formates is then separated from the treated particles and any insoluble materials formed during the treatment process, and recycled to the gasification process where the alkali metal formates serve as at least a portion of the alkali metal constituents which comprise the alkali metal-containing catalyst. This process permits increased recovery of alkali metal constituents, thereby decreasing the overall cost of the gasification process by reducing the amount of makeup alkali metal compounds necessary.

  5. Alkali aluminosilicate melts and glasses: structuring at the middle range order of amorphous matter

    NASA Astrophysics Data System (ADS)

    Le Losq, C.; neuville, D. R.

    2012-12-01

    Rheological properties of silicate melts govern both magma ascension from the mantle to the surface of the earth and volcanological eruptions styles and behaviours. It is well known that several parameters impact strongly these properties, such as for instance the temperature, pressure, chemical composition and volatiles concentration, finally influencing eruptive behaviour of volcanoes. In this work, we will focus on the Na2O-K2O-Al2O3-SiO2 system, which is of a prime importance because it deals with a non-negligible part of natural melts, like for instance the Vesuvius (Italy) or Erebus (Antartica) magmas. In an oncoming paper in Chemical Geology (Le Losq and Neuville, 2012), we have communicated results of the study of mixing Na-K in tectosilicate melts containing a high concentration of silica (≥75mol%). In the present communication, we will enlarge this first point of view to tectosilicate melts presenting a lower silica concentration. We will first present our viscosity data, and then the Adam and Gibbs theory that allows theoretically modelling Na-K mixing in aluminosilicate melts by using the so-called "mixed alkali effect". On the basis of the rheological results, the Na-K mixing cannot be explained with the ideal "mixed alkali effect", which involves random exchange of Na-K cationic pairs. To go further and as rheological properties are directly linked with structural properties, we will present our first results obtained by Raman and NMR spectroscopy. These last ones provide important structural pieces of information on the polymerization state of glasses and melts, and also on the environment of tetrahedrally coordinated cations. Rheological and structural results all highlight that Na and K are not randomly distributed in aluminosilicate glasses and melts networks. Na melts present a network with some channels and a non-random distribution of Al and Si. K networks are different. They also present a non-random distribution of Al and Si, but in two sub

  6. Optical properties and electronic structure of alkali doped SWNT

    NASA Astrophysics Data System (ADS)

    Nemes, Norbert M.; Fischer, John E.; Kamarás, Katalin; Borondics, Ferenc; Tanner, David B.; Rinzler, Andrew G.

    2003-03-01

    Alkali doped SWNT exhibit colors similar to alkali doped graphite (GIC). We study their electronic structure with IR reflectivity; the alkali dopants donate their valence electron to the SWNT host, so the free carrier concentration increases, shifting the Drude-edge into the visible spectral range. This is accompanied by a large shift of the Fermi-level, so the characteristic transitions between the 1D van Hove singularities of the undoped SWNT diminish. The presence of the alkali ions around the SWNT breaks the translational symmetry and increases coupling between parallel tubes within ropes. The momentum relaxation time shortens as the ropes become more three dimensional; alkali disorder contributes to the scattering. In p-type, HNO3 doped SWNT, the charge transfer is smaller; only the first subband of the semiconducting tubes gets depleted, shown by the disappearance of the first van Hove transition. This indicates a Fermi-level shift of ˜0.3 eV. The reflectivity has structure at low energy, which moves the Drude-peak to a sharp, intense peak at 0.1 eV in the optical conductivity, reminiscent of quasi-1D TTF-TCNQ.

  7. Electrolytic method to make alkali alcoholates using ion conducting alkali electrolyte/separator

    DOEpatents

    Joshi, Ashok V.; Balagopal, Shekar; Pendelton, Justin

    2011-12-13

    Alkali alcoholates, also called alkali alkoxides, are produced from alkali metal salt solutions and alcohol using a three-compartment electrolytic cell. The electrolytic cell includes an anolyte compartment configured with an anode, a buffer compartment, and a catholyte compartment configured with a cathode. An alkali ion conducting solid electrolyte configured to selectively transport alkali ions is positioned between the anolyte compartment and the buffer compartment. An alkali ion permeable separator is positioned between the buffer compartment and the catholyte compartment. The catholyte solution may include an alkali alcoholate and alcohol. The anolyte solution may include at least one alkali salt. The buffer compartment solution may include a soluble alkali salt and an alkali alcoholate in alcohol.

  8. The calcium-alkali syndrome.

    PubMed

    Arroyo, Mariangeli; Fenves, Andrew Z; Emmett, Michael

    2013-04-01

    The milk-alkali syndrome was a common cause of hypercalcemia, metabolic alkalosis, and renal failure in the early 20th century. It was caused by the ingestion of large quantities of milk and absorbable alkali to treat peptic ulcer disease. The syndrome virtually vanished after introduction of histamine-2 blockers and proton pump inhibitors. More recently, a similar condition called the calcium-alkali syndrome has emerged as a common cause of hypercalcemia and alkalosis. It is usually caused by the ingestion of large amounts of calcium carbonate salts to prevent or treat osteoporosis and dyspepsia. We describe a 78-year-old woman who presented with weakness, malaise, and confusion. She was found to have hypercalcemia, acute renal failure, and metabolic alkalosis. Upon further questioning, she reported use of large amounts of calcium carbonate tablets to treat recent heartburn symptoms. Calcium supplements were discontinued, and she was treated with intravenous normal saline. After 5 days, the calcium and bicarbonate levels normalized and renal function returned to baseline. In this article, we review the pathogenesis of the calcium-alkali syndrome as well as the differences between the traditional and modern syndromes. PMID:23543983

  9. Communication: Dimensionality of the ionic conduction pathways in glass and the mixed-alkali effect.

    PubMed

    Novy, Melissa; Avila-Paredes, Hugo; Kim, Sangtae; Sen, Sabyasachi

    2015-12-28

    A revised empirical relationship between the power law exponent of ac conductivity dispersion and the dimensionality of the ionic conduction pathway is established on the basis of electrical impedance spectroscopic (EIS) measurements on crystalline ionic conductors. These results imply that the "universal" ac conductivity dispersion observed in glassy solids is associated with ionic transport along fractal pathways. EIS measurements on single-alkali glasses indicate that the dimensionality of this pathway D is ∼2.5, while in mixed-alkali glasses, D is lower and goes through a minimum value of ∼2.2 when the concentrations of the two alkalis become equal. D and σ display similar variation with alkali composition, thus suggesting a topological origin of the mixed-alkali effect. PMID:26723583

  10. Advancements in Anion Exchange Membrane Cations

    SciTech Connect

    Sturgeon, Matthew R.; Long, Hai; Park, Andrew M.; Pivovar, Bryan S.

    2015-10-15

    Anion-exchange membrane fuel cells (AME-FCs) are of increasingly popular interest as they enable the use of non-Pt fuel cell catalysts, the primary cost limitation of proton exchange membrane fuel cells. Benzyltrimethyl ammonium (BTMA) is the standard cation that has historically been utilized as the hydroxide conductor in AEMs. Herein we approach AEMs from two directions. First and foremost we study the stability of several different cations in a hydroxide solution at elevated temperatures. We specifically targeted BTMA and methoxy and nitro substituted BTMA. We've also studied the effects of adding an akyl spacer units between the ammonium cation and the phenyl group. In the second approach we use computational studies to predict stable ammonium cations, which are then synthesized and tested for stability. Our unique method to study cation stability in caustic conditions at elevated temperatures utilizes Teflon Parr reactors suitable for use under various temperatures and cation concentrations. NMR analysis was used to determine remaining cation concentrations at specific time points with GCMS analysis verifying product distribution. We then compare the experimental results with calculated modeling stabilities. Our studies show that the electron donating methoxy groups slightly increase stability (compared to that of BTMA), while the electron withdrawing nitro groups greatly decrease stability in base. These results give insight into possible linking strategies to be employed when tethering a BTMA like ammonium cation to a polymeric backbone; thus synthesizing an anion exchange membrane.

  11. Decalcification resistance of alkali-activated slag.

    PubMed

    Komljenović, Miroslav M; Baščarević, Zvezdana; Marjanović, Nataša; Nikolić, Violeta

    2012-09-30

    This paper analyses the effects of decalcification in concentrated 6M NH(4)NO(3) solution on mechanical and microstructural properties of alkali-activated slag (AAS). Portland-slag cement (CEM II/A-S 42.5 N) was used as a benchmark material. Decalcification process led to a decrease in strength, both in AAS and in CEM II, and this effect was more pronounced in CEM II. The decrease in strength was explicitly related to the decrease in Ca/Si atomic ratio of C-S-H gel. A very low ratio of Ca/Si ~0.3 in AAS was the consequence of coexistence of C-S-H(I) gel and silica gel. During decalcification of AAS almost complete leaching of sodium and tetrahedral aluminum from C-S-H(I) gel also took place. AAS showed significantly higher resistance to decalcification in relation to the benchmark CEM II due to the absence of portlandite, high level of polymerization of silicate chains, low level of aluminum for silicon substitution in the structure of C-S-H(I), and the formation of protective layer of polymerized silica gel during decalcification process. In stabilization/solidification processes alkali-activated slag represents a more promising solution than Portland-slag cement due to significantly higher resistance to decalcification. PMID:22818592

  12. Edelman's equation is valid in acute hyponatremia in a porcine model: plasma sodium concentration is determined by external balances of water and cations.

    PubMed

    Overgaard-Steensen, Christian; Larsson, Anders; Bluhme, Henrik; Tønnesen, Else; Frøkiaer, Jørgen; Ring, Troels

    2010-01-01

    Acute hyponatremia is a serious condition, which poses major challenges. Of particular importance is what determines plasma sodium concentration ([Na(+)]). Edelman introduced an explicit model to describe plasma [Na(+)] in a population as [Na(+)] = alpha.(exchangeable Na(+) + exchangeable K(+))/(total body water) - beta. Evidence for the clinical utility of the model in the individual and in acute hyponatremia is sparse. We, therefore, investigated how the measured plasma [Na(+)] could be predicted in a porcine model of hyponatremia. Plasma [Na(+)] was estimated from in vivo-determined balances of water, Na(+), and K(+), according to Edelman's equation. Acute hyponatremia was induced with desmopressin acetate and infusion of a 2.5% glucose solution in anesthetized pigs. During 480 min, plasma [Na(+)] and osmolality were reduced from 136 (SD 2) to 120 mmol/l (SD 3) and from 284 (SD 4) to 252 mosmol/kgH(2)O (SD 5), respectively. The following interpretations were made. First, Edelman's model, which, besides dilution, takes into account Na(+) and K(+), fits plasma [Na(+)] significantly better than dilution alone. Second, a common value of alpha = 1.33 (SD 0.08) and beta = -13.04 mmol/l (SD 7.68) for all pigs explains well the plasma [Na(+)] in the individual animal. Third, measured exchangeable Na(+) and calculated exchangeable Na(+) + K(+) per weight in the pigs are close to Edelman's findings in humans, whereby the methods are cross-validated. In conclusion, plasma [Na(+)] can be explained in the individual animal by external balances, according to Edelman's construct in acute hyponatremia. PMID:19864338

  13. Progress in Understanding Alkali-Alkali Spin Relaxation

    NASA Astrophysics Data System (ADS)

    Erickson, Christopher J.; Happer, William; Chann, Bien; Kadlecek, Stephen; Anderson, L. W.; Walker, Thad G.

    2000-06-01

    In extensive experiments we have shown that a spin interaction with a relatively long correlation time causes much of the spin relaxation in very dense alkali-metal vapors. The spin relaxation is affected by the pressure of the helium or nitrogen buffer gas, although there is little dependence at pressures above one atmosphere. There are substantial differences in the relaxation rates for different isotopes of the same element, for example ^87Rb and ^85Rb. We have completed extensive modeling of how singlet and triplet dimers and doublet trimers of the alkali-metal atoms could cause spin relaxation in dense alkali-metal vapors. In the case of doublet trimers or triplet dimers, we assume the main coupling to the nuclear spins is through the Fermi Contact interaction with the unpaired electrons. Spin loss to the rotation of the molecule is assumed to occur through the electronic spin-rotation and spin-axis (dipole-dipole) interactions for the triplet dimers. For the singlet dimers, we assume that the nuclear spins couple directly to the rotational angular momentum of the molecule through the electric quadrupole interaction. We account for all of the total nuclear spin states that occur for the dimers and trimers. We have also considered the possibility that the collisional breakup and formation rates of the dimers or trimers could saturate with increasing buffer gas pressure. Such saturation occurs in many other unimolecular reactions and is often ascribed to breakup through activated states.

  14. A study on optical properties of poly (ethylene oxide) based polymer electrolyte with different alkali metal iodides

    NASA Astrophysics Data System (ADS)

    Rao, B. Narasimha; Suvarna, R. Padma

    2016-05-01

    Polymer electrolytes were prepared by adding poly (ethylene glycol) dimethyl ether (PEGDME), TiO2 (nano filler), different alkali metal iodide salts RI (R+=Li+, Na+, K+, Rb+, Cs+) and I2 into Acetonitrile gelated with Poly (ethylene oxide) (PEO). Optical properties of poly (ethylene oxide) based polymer electrolytes were studied by FTIR, UV-Vis spectroscopic techniques. FTIR spectrum reveals that the alkali metal cations were coordinated to ether oxygen of PEO. The optical absorption studies were made in the wavelength range 200-800 nm. It is observed that the optical absorption increases with increase in the radius of alkali metal cation. The optical band gap for allowed direct transitions was evaluated using Urbach-edges method. The optical properties such as optical band gap, refractive index and extinction coefficient were determined. The studied polymer materials are useful for solar cells, super capacitors, fuel cells, gas sensors etc.

  15. Raman spectroscopic investigation of alkali-metal hexachloro compounds of refractory metals

    SciTech Connect

    Kipouros, G.J.; Flint, J.H.; Sadoway, D.R.

    1985-11-06

    The Raman spectra of molten alkali-metal hexachlorozirconate, hexachlorohafnate, hexachloroniobate, and hexachlorotantalate compounds have been obtained in the temperature range 623-1143 K. The results confirm that the refractory metal exists in the form of an octahedrally coordinated complex anion that is stable even in the molten state. For a given refractory metal the frequency of the nu/sub 1/ line increases as the size of the alkali-metal cation decreases. For a given alkali metal the frequency of the nu/sub 1/ line increases as the valence of the refractory metal increases. This last observation may serve as the basis for detecting, by Raman spectroscopy, aliovalent species that may form during the electrolysis of melts containing refractory-metal chlorides. 22 references, 4 figures, 2 tables.

  16. Positron-alkali atom scattering

    NASA Technical Reports Server (NTRS)

    Mceachran, R. P.; Horbatsch, M.; Stauffer, A. D.; Ward, S. J.

    1990-01-01

    Positron-alkali atom scattering was recently investigated both theoretically and experimentally in the energy range from a few eV up to 100 eV. On the theoretical side calculations of the integrated elastic and excitation cross sections as well as total cross sections for Li, Na and K were based upon either the close-coupling method or the modified Glauber approximation. These theoretical results are in good agreement with experimental measurements of the total cross section for both Na and K. Resonance structures were also found in the L = 0, 1 and 2 partial waves for positron scattering from the alkalis. The structure of these resonances appears to be quite complex and, as expected, they occur in conjunction with the atomic excitation thresholds. Currently both theoretical and experimental work is in progress on positron-Rb scattering in the same energy range.

  17. Alkali metal/sulfur battery

    DOEpatents

    Anand, Joginder N.

    1978-01-01

    Alkali metal/sulfur batteries in which the electrolyte-separator is a relatively fragile membrane are improved by providing means for separating the molten sulfur/sulfide catholyte from contact with the membrane prior to cooling the cell to temperatures at which the catholyte will solidify. If the catholyte is permitted to solidify while in contact with the membrane, the latter may be damaged. The improvement permits such batteries to be prefilled with catholyte and shipped, at ordinary temperatures.

  18. Superconductivity in alkali metal fullerides

    NASA Astrophysics Data System (ADS)

    Murphy, D. W.; Rosseinsky, M. J.; Haddon, R. C.; Ramirez, A. P.; Hebard, A. F.; Tycko, R.; Fleming, R. M.; Dabbagh, G.

    1991-12-01

    The recent synthesis of macroscopic quantities of spherical molecular carbon compounds, commonly called fullerenes, has stimulated a wide variety of studies of the chemical and physical properties of this novel class of compounds. We discovered that the smallest of the known fullerenes, C 60, could be made conducting and superconducting by reaction with alkali metals. In this paper, an overview of the motivation for these discoveries and some recent results are presented.

  19. Elution of Re-188 from W-188/Re-188 generators with salts of weak acids permits efficient concentration to low volumes using a new tandem cation/anion exchange system

    SciTech Connect

    Guhlke, S. |; Beets, A.L.; Knapp, F.F. Jr.

    1997-05-01

    Re-188, available from a W-188/Re-188 generator, is an important therapeutic radioisotope for bone pain palliation, cancer therapy and intravascular brachytherapy, etc. Because of the relatively low specific activity of reactor-produced W-188 (ORNL HFIR, 296-370 MBq mCi/mg W-186 for 2 cycles), methods of concentrating the Re-188 bolus (10-12 mL) from clinical scale (18.5-37 BGq W-188) generators (5-6 gm alumina) are thus very important. We demonstrate for the first time a new strategy of generator elution with salts of weak acids and specific perrhenate anion {open_quotes}trapping{close_quotes} with QMA anion columns. Re-188 perrhenate is efficiently eluted (65-75%) from the alumina-based generator with 0.15-0.3 M ammonium acetate. An acetic acid solution of Re-188 perrhenic acid is obtained by subsequent on-line passage of the generator eluant through a DOWEX AG 50Wx8 (200-400 mesh, H{sup +} form) column. Since acetic acid is not ionized (< 0.001%) at this pH (< pK{sub a} = 4.76) the perrhenate anion is then specifically trapped on a QMA {open_quotes}Light{close_quotes} anion extraction column. QMA elution with 0.9% NaCl, provides Re-188 perrhenate solution in <1 mL. Concentration of 10-20 mL of Re-188 solution (> 15 BGq) in <1 mL has been demonstrated using this simple new approach, which is also effective for concentration of Tc-99m from low specific activity Mo-99 (n,y) generators. The cation/anion tandem system is inexpensive and disposable and use can be easily automated. The availability of this very simple, efficient system is important for broad use of rhenium-188.

  20. Alkali metal sources for OLED devices

    NASA Astrophysics Data System (ADS)

    Cattaneo, Lorena; Longoni, Giorgio; Bonucci, Antonio; Tominetti, Stefano

    2005-07-01

    In OLED organic layers electron injection is improved by using alkali metals as cathodes, to lower work function or, as dopants of organic layer at cathode interface. The creation of an alkali metal layer can be accomplished through conventional physical vapor deposition from a heated dispenser. However alkali metals are very reactive and must be handled in inert atmosphere all through the entire process. If a contamination takes place, it reduces the lithium deposition rate and also the lithium total yield in a not controlled way. An innovative alkali metal dispensing technology has been developed to overcome these problems and ensure OLED alkali metal cathode reliability. The alkali Metal dispenser, called Alkamax, will be able to release up to a few grams of alkali metals (in particular Li and Cs) throughout the adoption of a very stable form of the alkali metal. Lithium, for example, can be evaporated "on demand": the evaporation could be stopped and re-activated without losing alkali metal yield because the metal not yet consumed remains in its stable form. A full characterization of dispensing material, dispenser configuration and dispensing process has been carried out in order to optimize the evaporation and deposition dynamics of alkali metals layers. The study has been performed applying also inside developed simulations tools.

  1. Effect of the alkaline cation size on the conductivity in gel polymer electrolytes and their influence on photo electrochemical solar cells.

    PubMed

    Bandara, T M W J; Fernando, H D N S; Furlani, M; Albinsson, I; Dissanayake, M A K L; Ratnasekera, J L; Mellander, B-E

    2016-04-20

    The nature and concentration of cationic species in the electrolyte exert a profound influence on the efficiency of nanocrystalline dye-sensitized solar cells (DSSCs). A series of DSSCs based on gel electrolytes containing five alkali iodide salts (LiI, NaI, KI, RbI and CsI) and polyacrylonitrile with plasticizers were fabricated and studied, in order to investigate the dependence of solar cell performance on the cation size. The ionic conductivity of electrolytes with relatively large cations, K(+), Rb(+) and Cs(+), was higher and essentially constant, while for the electrolytes containing the two smaller cations, Na(+) and Li(+), the conductivity values were lower. The temperature dependence of conductivity in this series appears to follow the Vogel-Tamman-Fulcher equation. The sample containing the smallest cation shows the lowest conductivity and the highest activation energy of ∼36.5 meV, while K(+), Rb(+) and Cs(+) containing samples show an activation energy of ∼30.5 meV. DSSCs based on the gel electrolyte and a TiO2 double layer with the N719 dye exhibited an enhancement in the open circuit voltage with increasing cation size. This can be attributed to the decrease in the recombination rate of electrons and to the conduction band shift resulting from cation adsorption by TiO2. The maximum efficiency value, 3.48%, was obtained for the CsI containing cell. The efficiencies shown in this study are lower compared to values reported in the literature, and this can be attributed to the use of a single salt and the absence of other additives, since the focus of the present study was to analyze the cation effect. The highest short circuit current density of 9.43 mA cm(-2) was shown by the RbI containing cell. The enhancement of the solar cell performance with increasing size of the cation is discussed in terms of the effect of the cations on the TiO2 anode and ion transport in the electrolyte. In liquid electrolyte based DSSCs, the short circuit current density

  2. The cubyl cation rearrangements.

    PubMed

    Jalife, Said; Mondal, Sukanta; Cabellos, Jose Luis; Martinez-Guajardo, Gerardo; Fernandez-Herrera, Maria A; Merino, Gabriel

    2016-02-25

    Born-Oppenheimer molecular dynamics simulations and high-level ab initio computations predict that the cage-opening rearrangement of the cubyl cation to the 7H(+)-pentalenyl cation is feasible in the gas phase. The rate-determining step is the formation of the cuneyl cation with an activation barrier of 25.3 kcal mol(-1) at the CCSD(T)/def2-TZVP//MP2/def2-TZVP level. Thus, the cubyl cation is kinetically stable enough to be formed and trapped at moderate temperatures, but it may be rearranged at higher temperatures. PMID:26880646

  3. Ultrafiltration membrane reactor for obtaining experimental reaction rates at defined concentrations of inhibiting sugars during enzymatic saccharifiction of alkali-pretreated sallow: formulation of a simple empirical rate equation

    SciTech Connect

    Frennesson, I.; Traegaardh, G.; Hahn-Haegerdal, B.

    1985-09-01

    The kinetics of the enzymatic hydrolysis of sodium hydroxide-pretreated sallow were studied in an ultrafiltration membrane reactor in the presence of different concentrations of glucose. In the UF membrane reactor low-molecular-weight products were continuously removed at a low dilution rate and replaced by a buffer solution that contained different concentrations of glucose, which made it possible to keep the inhibiting product concentration constant throughout an experiment. The reaction rate was related to the degree of substrate conversion and a mathematical relationship was formulated that describes the influence of the product concentration on the rate coefficient.

  4. Structural models for alkali-metal complexes of polyacetylene

    NASA Astrophysics Data System (ADS)

    Murthy, N. S.; Shacklette, L. W.; Baughman, R. H.

    1990-02-01

    Structural models for a stage-2 complex are proposed for polyacetylene doped with less than about 0.1 potassium or rubidium atoms per carbon. These structures utilize as a basic motif an alkali-metal column surrounded by four planar-zig-zag polyacetylene chains, a structure found at the highest dopant levels. In the new stage-2 structures, each polyacetylene chain neighbors only one alkali-metal column, so the phase contains four polymer chains per alkali-metal column. Basic structural aspects for stage-1 and stage-2 structures are now established for both potassium- and rubidium-doped polyacetylene. X-ray-diffraction and electrochemical data show that undoped and doped phases coexist at low dopant concentrations (<0.06 K atom per C). X-ray-diffraction data, down to a Bragg spacing of 1.3 Å, for polyacetylene heavily doped with potassium (0.125-0.167 K atom per C) is fully consistent with our previously proposed stage-1 tetragonal unit cell containing two polyacetylene chains per alkali-metal column. There is no evidence for our samples requiring a distortion to a monoclinic unit cell as reported by others for heavily doped samples. The nature of structural transformations and the relationship between structure and electronic properties are discussed for potassium-doped polyacetylene.

  5. EPR study of polarons in a conducting polymer with nondegenerate ground states: Alkali metal complexes of poly (p-phenylene) and phenylene oligomers

    SciTech Connect

    Kispert, L.D.; Joseph, J.; Miller, G.G.; Baughman, R.H.

    1984-08-15

    EPR measurements are used to characterize electronic states relevant for carrier transport in alkali metal doped poly(p-phenylene), PPP, fully deuterated poly(p-phenylene), DPPP, and phenylene oligomers. Observed spin concentrations per carbon are at least one decade higher than the Curie spin concentration for Na-doped polyacetylene. The number of these spins, which likely corresponds to polarons (mobile radical anions), is much less than the amount of alkali metal dopant, suggesting that much of the charge on the polymer chains is in bipolarons (spinless dianions). Relevant to the interaction between spins on the polymer chain and the metal cations, the observed g values are close to the free electron value and do not substantially vary with the donor dopant, temperature, or the molecular weight of the phenylene chain. Although the spin-orbit effect on g values is small, room temperature linewidth tends to increase with increasing atomic number of dopant: suggesting some interaction, albeit a smaller magnitude effect than for alkali-metal graphite complexes. The EPR linewidths are exchange narrowed and proton hyperfine broadening is significant. The latter explains the generally broader linewidths for doped PPP than for doped DPPP. The measured susceptibilities have a temperature dependence which suggests equilibrium between separated polaron defects and singlet and triplet spin states formed intermolecularly via polaron pairing. The interaction is antiferromagnetic and the binding energy between polarons is about 2.2 to 3.3 meV. An upper limit estimate of the Fermi-surface density of states for K-doped PPP (0.7 states/eV phenyl) is derived from an upper limit estimate of Pauli susceptibility.

  6. Soil Cation Status in Southern California: Interactions of Vehicular Emissions

    NASA Astrophysics Data System (ADS)

    Rossi, R.; Bain, D. J.; Jenerette, D.; Clarke, L. W.

    2012-12-01

    Roadside soils are often enriched in trace metals due to vehicular deposition. However, less attention is given to base cation pools in roadside soils. Relatively high loadings of nitrate from vehicular exhaust should acidify roadside soils, potentially mobilizing cationic species by displacing them from soil exchange sites. In contrast, weathering of road materials can contribute substantial amounts of these cations to the same soils, potentially replenishing cation pools. Base cations are essential nutrients and these dynamics may alter ecosystem processes in near-road environments. Metal concentrations in park and garden soils collected from Southern California (Los Angeles and Riverside Counties) were examined across gradients of road network intensity, climate and geology. In these samples, base cation concentrations decrease in areas of denser road networks. Base cation concentrations also decrease with distance from the road, with near-road samples relatively depleted in base cation concentrations. In addition, base cation concentrations are associated with traffic flux density, with exchange pools decreasing near heavily trafficked areas. These relationships suggest road activity is mobilizing cations, depleting near-road soils of essential nutrient pools, despite road material weathering. This depletion of soil nutrients from exchange pools in roadside soils likely influences local ecological function in unpredictable ways. This observation lays the groundwork for continued characterization of soil metal processes in the increasingly common roadside environment.

  7. Rhizomes Help the Forage Grass Leymus chinensis to Adapt to the Salt and Alkali Stresses

    PubMed Central

    Li, Xiaoyu; Wang, Junfeng; Lin, Jixiang; Wang, Ying; Mu, Chunsheng

    2014-01-01

    Leymus chinensis has extensive ecological adaptability and can grow well in saline-alkaline soils. The knowledge about tolerance mechanisms of L. chinensis could be base for utilization of saline-alkaline soils and grassland restoration and rebuilding. Two neutral salts (NaCl : Na2SO4 = 9 : 1) and two alkaline salts (NaHCO3 : Na2CO3 = 9 : 1) with concentration of 0, 100, and 200 mmol/L were used to treat potted 35-day-old seedlings with rhizome growth, respectively. After 10 days, the biomass and number of daughter shoots all decreased, with more reduction in alkali than in salt stress. The rhizome biomass reduced more than other organs. The number of daughter shoots from rhizome was more than from tillers. Under both stresses, Na+ contents increased more in rhizome than in other organs; the reduction of K+ content was more in underground than aerial tissue. Anion ions or organic acids were absorbed to neutralize cations. Na+ content in stem and leaf increased markedly in high alkalinity (200 mmol/L), with accumulation of soluble sugar and organic acids sharply. Rhizomes help L. chinensis to adapt to saline and low alkaline stresses by transferring Na+. However, rhizomes lost the ability to prevent Na+ transport to aerial organs under high alkalinity, which led to severe growth inhibition of L. chinensis. PMID:25121110

  8. Rhizomes help the forage grass Leymus chinensis to adapt to the salt and alkali stresses.

    PubMed

    Li, Xiaoyu; Wang, Junfeng; Lin, Jixiang; Wang, Ying; Mu, Chunsheng

    2014-01-01

    Leymus chinensis has extensive ecological adaptability and can grow well in saline-alkaline soils. The knowledge about tolerance mechanisms of L. chinensis could be base for utilization of saline-alkaline soils and grassland restoration and rebuilding. Two neutral salts (NaCl : Na₂SO₄ = 9 : 1) and two alkaline salts (NaHCO₃ : Na₂CO₃ = 9 : 1) with concentration of 0, 100, and 200 mmol/L were used to treat potted 35-day-old seedlings with rhizome growth, respectively. After 10 days, the biomass and number of daughter shoots all decreased, with more reduction in alkali than in salt stress. The rhizome biomass reduced more than other organs. The number of daughter shoots from rhizome was more than from tillers. Under both stresses, Na(+) contents increased more in rhizome than in other organs; the reduction of K(+) content was more in underground than aerial tissue. Anion ions or organic acids were absorbed to neutralize cations. Na(+) content in stem and leaf increased markedly in high alkalinity (200 mmol/L), with accumulation of soluble sugar and organic acids sharply. Rhizomes help L. chinensis to adapt to saline and low alkaline stresses by transferring Na(+). However, rhizomes lost the ability to prevent Na(+) transport to aerial organs under high alkalinity, which led to severe growth inhibition of L. chinensis. PMID:25121110

  9. From T2,2@Bmmim to Alkali@T2,2@Bmmim Ivory Ball-like Clusters: Ionothermal Syntheses, Precise Doping, and Photocatalytic Properties.

    PubMed

    Du, Cheng-Feng; Li, Jian-Rong; Zhang, Bo; Shen, Nan-Nan; Huang, Xiao-Ying

    2015-06-15

    Presented here are the syntheses, structures, and properties of an In-Sn-Se compound based on a ternary super-supertetrahedral T2,2 cluster nested by Bmmim cations and two of its alkali-doped quaternary analogues. By means of a one-pot ionothermal method, an alkali metal ion (Cs(+) or Rb(+)) could be precisely doped into the central cavity of the cluster, forming an alkali@T2,2@Bmmim quaternary cluster. Remarkably, the undoped compound exhibited excellent stability and visible light photodegradation ability over a wide range of pH, especially in acidic conditions. PMID:26034842

  10. Charge oscillations and structure for alkali-metal-doped polyacetylene

    NASA Astrophysics Data System (ADS)

    Baughman, R. H.; Murthy, N. S.; Eckhardt, H.; Kertesz, M.

    1992-11-01

    Symmetry-breaking structural and charge oscillations are calculated for (CpHp)- lattices (p=5 to 9) and used to predict Coulombic expansion coefficients, x-ray photoelectron spectra, and crystallographic features that can be compared with experimental results. Extension of these predictions to other dopant concentrations is provided by derived analytical expressions. The parameters for the infinite lattices are derived from oligomer-ion results obtained from modified neglect of differential overlap calculations. Such calculations on oligomer ions with different parametrizations provide essentially identical changes in charge and structural parameters upon doping and these changes are in excellent agreement with the results of infinite-chain calculations. The degree to which oligomer-ion segments retain the structural parameters of charged arrays for the infinite lattice is remarkable. Derived geometries and charge distributions indicate two different types of charged defects, solitons (or antisolitons) and split solitons (or split antisolitons), and the geometry and charge distribution of the latter defects is shown to correspond to the average of those for two soliton lattices that have a relative shift of two CH units. At least in the absence of an external Coulomb field, soliton and split-soliton lattices for p odd are quasidegenerate, and the lattices for p even consist of alternating sequences of solitons and split antisolitons. Large oscillations in local chain-axis direction are predicted, which is a consequence of both oscillations in bond angles and the nonequivalence of even (and odd) bond lengths. Including these effects provides predicted Coulombic expansion coefficients that are in good agreement with observations for Na-doped polyacetylene. Much smaller bond-angle oscillations are predicted for anion lattices than for cation lattices, which can be at least partially explained by Coulomb effects. Observed 13C NMR chemical shifts are consistent with

  11. Plasma assisted spectroscopic monitoring of alkali metals in pressurised combustion and gasification

    SciTech Connect

    Haeyrinen, V.T.; Hernberg, R.G.

    1995-07-01

    The paper describes an instrument for on-line concentration measurement of vaporised alkali compounds in pressurised industrial combustion and gasification processes. The measurement is based on Plasma Excited Alkali Resonance Line Spectroscopy (PEARLS) at the elevated pressure (1-3 MPa) of the process. Results are presented from laboratory calibration measurements and test measurements of sodium and potassium vapours resulting from the combustion of coal powder in a pressurised entrained flow reactor.

  12. Detection of alkali-silica reaction swelling in concrete by staining

    DOEpatents

    Guthrie, Jr., George D.; Carey, J. William

    1998-01-01

    A method using concentrated aqueous solutions of sodium cobaltinitrite and rhodamine B is described which can be used to identify concrete that contains gels formed by the alkali-silica reaction (ASR). These solutions present little health or environmental risk, are readily applied, and rapidly discriminate between two chemically distinct gels; K-rich, Na--K--Ca--Si gels are identified by yellow staining, and alkali-poor, Ca--Si gels are identified by pink staining.

  13. Detection of alkali-silica reaction swelling in concrete by staining

    DOEpatents

    Guthrie, G.D. Jr.; Carey, J.W.

    1998-04-14

    A method using concentrated aqueous solutions of sodium cobalt nitrite and rhodamine B is described which can be used to identify concrete that contains gels formed by the alkali-silica reaction (ASR). These solutions present little health or environmental risk, are readily applied, and rapidly discriminate between two chemically distinct gels; K-rich, Na-K-Ca-Si gels are identified by yellow staining, and alkali-poor, Ca-Si gels are identified by pink staining.

  14. Extra-framework cation release from heulandite-type rich tuffs on exchange with NH(4)(+).

    PubMed

    Kantiranis, N; Sikalidis, K; Godelitsas, A; Squires, C; Papastergios, G; Filippidis, A

    2011-06-01

    The outgoing cations of Greek heulandite-rich tuff samples (heulandite type-III, 91wt.%, mica 4wt.%, feldspar 5wt. %, CEC 2.22meq/g) were analysed upon exchange with ammonium acetate using atomic absorption spectrometry (AAS). The kinetic curves of each cation were investigated over a total time of contact of 720h with sampling at frequent intervals. The materials were examined by powder X-ray diffraction, SEM-EDS, and AAS. The sorption ability was measured using the ammonium acetate saturation method. It was found that Ca(2+) presents an unexpected extra-framework release and a surprisingly high degree of exchange (90%). The exchange of Mg (57%) is also worthy of note whereas the behavior of K(+) showed an expected rapid initial release. The behavior of Na(+) must be similar. However, its lower concentration in the zeolitic material minimizes its overall significance somewhat. On the other hand, Ca(2+) and Mg(2+) release is kinetically much slower, compared to that of alkali metal ions, and this phenomenon indicates that different exchange energies are needed till final equilibrium. PMID:21296480

  15. Cation effects during aggregation and agglomeration of gibbsite particles under synthetic Bayer crystallisation conditions

    NASA Astrophysics Data System (ADS)

    Prestidge, Clive A.; Ametov, Igor

    2000-02-01

    Rheological methods have been used to study the influence of the liquor cation (sodium versus potassium) on the time-dependent gibbsite particle interactions that occur during Bayer process crystallisation. The temperature, supersaturation and seeding levels investigated simulate those experienced in industrial crystallisers. Gibbsite agglomeration was shown to occur by reversible aggregation followed by irreversible cementation. These two sub-steps were individually characterised by careful choice of seed surface area and liquor supersaturation during batch crystallisation. At seed loading levels less than 10% w/w aggregates are rapidly cemented into agglomerates, this is more pronounced in sodium- than potassium-based liquors. These suspensions were Newtonian and the extent of agglomeration correlated with their viscosity. At seed loading levels greater than 20% w/w particle aggregation resulted in extensively time-dependent and non-Newtonian rheology. However, the aggregates did not undergo cementation into agglomerates and no irreversible size enlargement was evident. Yield stress development with time was used to probe the kinetics of aggregation and quantify the particle interaction behaviour. The rate and extent of the particle network formation is more pronounced in sodium rather than potassium-based liquors, supersaturation dependent, alkali concentration dependent, but only weakly temperature dependent. These findings are discussed with respect to the chemical and physical mechanisms of agglomeration in Bayer crystallisation and the role of cation.

  16. Simple electrolyte solutions: Comparison of DRISM and molecular dynamics results for alkali halide solutions

    PubMed Central

    Joung, In Suk; Luchko, Tyler; Case, David A.

    2013-01-01

    Using the dielectrically consistent reference interaction site model (DRISM) of molecular solvation, we have calculated structural and thermodynamic information of alkali-halide salts in aqueous solution, as a function of salt concentration. The impact of varying the closure relation used with DRISM is investigated using the partial series expansion of order-n (PSE-n) family of closures, which includes the commonly used hypernetted-chain equation (HNC) and Kovalenko-Hirata closures. Results are compared to explicit molecular dynamics (MD) simulations, using the same force fields, and to experiment. The mean activity coefficients of ions predicted by DRISM agree well with experimental values at concentrations below 0.5 m, especially when using the HNC closure. As individual ion activities (and the corresponding solvation free energies) are not known from experiment, only DRISM and MD results are directly compared and found to have reasonably good agreement. The activity of water directly estimated from DRISM is nearly consistent with values derived from the DRISM ion activities and the Gibbs-Duhem equation, but the changes in the computed pressure as a function of salt concentration dominate these comparisons. Good agreement with experiment is obtained if these pressure changes are ignored. Radial distribution functions of NaCl solution at three concentrations were compared between DRISM and MD simulations. DRISM shows comparable water distribution around the cation, but water structures around the anion deviate from the MD results; this may also be related to the high pressure of the system. Despite some problems, DRISM-PSE-n is an effective tool for investigating thermodynamic properties of simple electrolytes. PMID:23387564

  17. Kinetics of Coloration in Photochromic Tungsten(VI) Oxide/Silicon Oxycarbide/Silica Hybrid Xerogel: Insight into Cation Self-diffusion Mechanisms.

    PubMed

    Adachi, Kenta; Tokushige, Masataka; Omata, Kaoru; Yamazaki, Suzuko; Iwadate, Yoshiaki

    2016-06-01

    Silicon oxycarbide/silica composites with well-dispersed tungsten(VI) oxide (WO3) nanoparticles were obtained as transparent hybrid xerogels via an acid-catalyzed sol-gel process (hydrolysis/condensation polymerization) of 3-(triethoxysilyl)propyl methacrylate (TESPMA) and tetraethoxysilane (TEOS). The self-diffusion mechanism of alkali-metal cations and the kinetics of the photochromic coloration process in the WO3/TESPMA/TEOS hybrid xerogel systems have been systematically investigated. Under continuous UV illumination, a gradual color change (colorless → blue) corresponding to the reduction of W(6+) into W(5+) states in WO3 nanoparticles can be confirmed from the WO3/TESPMA/TEOS hybrid xerogels containing alkali-metal sulfates, although no coloration of the hybrid xerogel without alkali-metal sulfate was observed. The coloration behavior depended exclusively on a variety of alkali-metal cations present in the hybrid xerogel system. Furthermore, a detailed analysis of the self-diffusion mechanism confirmed that the alkali-metal cations electrostatically interact with a layer of unreacted silanol groups on the TESPMA/TEOS matrix surface, and subsequently pass through the interconnected pore network of the hybrid xerogel. More interestingly, in the context of an Arrhenius analysis, we found a good coincidence between the activation energies for alkali-metal cation self-diffusion and UV-induced coloration in the WO3/TESPMA/TEOS hybrid xerogel system containing the corresponding alkali-metal sulfate. It is experimentally obvious that the photochromic properties are dominated by the diffusion process of alkali-metal cations in the WO3/TESPMA/TEOS hybrid xerogel system. Such hybrid materials with cation-controlled photochromic properties will show promising prospects in applications demanding energy-efficient "smart windows" and "smart glasses". PMID:27159661

  18. Regeneration of Cation-Transport Capacity in HeLa Cell Membranes After Specific Blockade by Ouabain

    PubMed Central

    Vaughan, Gerald L.; Cook, John S.

    1972-01-01

    The cardiac glycoside, ouabain, inhibits alkali-cation transport in HeLa cells. It binds to 0.75 × 106 sites per cell, and the half-time for its dissociation is 16 hr. After partial blockade by ouabain, the cell generates new ouabain-binding sites, with total restoration of transport in 10% of a cell cycle(∼3 hr). This recovery requires protein synthesis and appears to be a response to altered cell-electrolyte content, since growth of cells in media with low K+ concentration enhances the titer of the transport enzyme in a fashion similar to the effect of ouabain. Totally blocked cells do not recover. PMID:4506784

  19. All-inorganic Germanium nanocrystal films by cationic ligand exchange

    DOE PAGESBeta

    Wheeler, Lance M.; Nichols, Asa W.; Chernomordik, Boris D.; Anderson, Nicholas C.; Beard, Matthew C.; Neale, Nathan R.

    2016-01-21

    In this study, we introduce a new paradigm for group IV nanocrystal surface chemistry based on room temperature surface activation that enables ionic ligand exchange. Germanium nanocrystals synthesized in a gas-phase plasma reactor are functionalized with labile, cationic alkylammonium ligands rather than with traditional covalently bound groups. We employ Fourier transform infrared and 1H nuclear magnetic resonance spectroscopies to demonstrate the alkylammonium ligands are freely exchanged on the germanium nanocrystal surface with a variety of cationic ligands, including short inorganic ligands such as ammonium and alkali metal cations. This ionic ligand exchange chemistry is used to demonstrate enhanced transport inmore » germanium nanocrystal films following ligand exchange as well as the first photovoltaic device based on an all-inorganic germanium nanocrystal absorber layer cast from solution. This new ligand chemistry should accelerate progress in utilizing germanium and other group IV nanocrystals for optoelectronic applications.« less

  20. All-Inorganic Germanium Nanocrystal Films by Cationic Ligand Exchange.

    PubMed

    Wheeler, Lance M; Nichols, Asa W; Chernomordik, Boris D; Anderson, Nicholas C; Beard, Matthew C; Neale, Nathan R

    2016-03-01

    We introduce a new paradigm for group IV nanocrystal surface chemistry based on room temperature surface activation that enables ionic ligand exchange. Germanium nanocrystals synthesized in a gas-phase plasma reactor are functionalized with labile, cationic alkylammonium ligands rather than with traditional covalently bound groups. We employ Fourier transform infrared and (1)H nuclear magnetic resonance spectroscopies to demonstrate the alkylammonium ligands are freely exchanged on the germanium nanocrystal surface with a variety of cationic ligands, including short inorganic ligands such as ammonium and alkali metal cations. This ionic ligand exchange chemistry is used to demonstrate enhanced transport in germanium nanocrystal films following ligand exchange as well as the first photovoltaic device based on an all-inorganic germanium nanocrystal absorber layer cast from solution. This new ligand chemistry should accelerate progress in utilizing germanium and other group IV nanocrystals for optoelectronic applications. PMID:26796765

  1. The interactions of sorbates with gallosilicates and alkali-metal exchanged gallosilicates

    NASA Astrophysics Data System (ADS)

    Limtrakul, J.; Kuno, M.; Treesukol, P.

    1999-11-01

    Structures, energetics and vibrational frequencies of the interaction of adsorbates with H-aluminosilicates (H-AlZ), H-gallosilicates (H-GaZ), alkali-metal exchanged aluminosilicates (X-AlZ) and alkali-metal exchanged gallosilicates (X-GaZ), where X being Li, Na, or K, have been carried out at B3LYP and HF levels of theory with 6-31G(d) as the basis set. The charge compensating alkali-metal ions can affect the catalytically active site (Si-O-T where T=Al or Ga) by weakening the Si-O, Al-O, and Ga-O bonds as compared to their anionic frameworks. Comparing the net stabilization energies, Δ ENSE, of the naked alkali-metal/H 2O adducts with those of the alkali-metal exchanged zeolite/H 2O systems, the latter amounts only to about 50% of the former, which is partly due to the destabilizing role of the negative zeolitic oxygen frameworks surrounding the cations. The interaction of sorbates with the alkali-metal exchanged gallosilicates can be employed to probe the field strength inside the catalytic frameworks as indicated by the plot of the binding energy, Δ E, versus 1/ RX-O w2, with R(X-O w) being the distance between the cationic nucleus and the oxygen atom of the adsorbate. The IR spectra of H 2O adsorbed on Na-AlZ are calculated to be 3584, 3651, and 1686 cm -1. The obtained results are in excellent agreement with the very recent experimental IR spectra of water adsorbed on Na-ZSM-5 of Zecchina et al. (J. Phys. Chem., 100 (1996) 16 484). Other important features, i.e. the correlation between Δ νOH and, Δ E, R(X-O w) , and 1/ RX-O w2, cationic size, demonstrate that the interactions of sorbates with alkali-metal exchanged gallosilicates are well approximated by electrostatic contribution.

  2. Structure of xanthan gum and cell ultrastructure at different times of alkali stress

    PubMed Central

    de Mello Luvielmo, Márcia; Borges, Caroline Dellinghausen; de Oliveira Toyama, Daniela; Vendruscolo, Claire Tondo; Scamparini, Adilma Regina Pippa

    2016-01-01

    The effect of alkali stress on the yield, viscosity, gum structure, and cell ultrastructure of xanthan gum was evaluated at the end of fermentation process of xanthan production by Xanthomonas campestris pv. manihotis 280-95. Although greater xanthan production was observed after a 24 h-alkali stress process, a lower viscosity was observed when compared to the alkali stress-free gum, regardless of the alkali stress time. However, this outcome is not conclusive as further studies on gum purification are required to remove excess sodium, verify the efficiency loss and the consequent increase in the polymer viscosity. Alkali stress altered the structure of xanthan gum from a polygon-like shape to a star-like form. At the end of the fermentation, early structural changes in the bacterium were observed. After alkali stress, marked structural differences were observed in the cells. A more vacuolated cytoplasm and discontinuities in the membrane cells evidenced the cell lysis. Xanthan was observed in the form of concentric circles instead of agglomerates as observed prior to the alkali stress. PMID:26887232

  3. Alkali extraction and in vitro antioxidant activity of Monascus mycelium polysaccharides.

    PubMed

    Wang, Pengrong; Chen, Danfeng; Jiang, Donghua; Dong, Xiameng; Chen, Panpan; Lin, Yaoxue

    2014-07-01

    In the present work, alkali extraction technology was used to optimize the extraction of Monascus mycelium polysaccharides for the first time. The extracting parameters of alkali extracted Monascus mycelium polysaccharides were optimized by Box-Behnken design (BBD). The optimum conditions were extraction temperature 49 °C, alkali concentration 7%, solvent/material ratio 23:1 (ml/g) and extraction time 2.3 h with an enhanced yield of 10.1%, compared with the yield 4.76% of hot water extraction, indicating that alkali extraction is a more efficient way. In order to discuss the biological activity of alkali extracted polysaccharides, we compared the in vitro antioxidant activity of alkali extracted polysaccharides (AMP) with hot water extracted polysaccharides (HMP). The result showed that AMP have the similar capability of scavenging both superoxide radical and 2, 2-diphenyl-1-picrylhydrazyl (DPPH) radical of HMP in vitro. Therefore, alkali extraction technology is not only a high-efficiency way to extract AMP, but also can retain the natural antioxidant activities of AMP, which can be used in pharmaceutical and food industries. PMID:24966417

  4. Structure of xanthan gum and cell ultrastructure at different times of alkali stress.

    PubMed

    Luvielmo, Márcia de Mello; Borges, Caroline Dellinghausen; Toyama, Daniela de Oliveira; Vendruscolo, Claire Tondo; Scamparini, Adilma Regina Pippa

    2016-01-01

    The effect of alkali stress on the yield, viscosity, gum structure, and cell ultrastructure of xanthan gum was evaluated at the end of fermentation process of xanthan production by Xanthomonas campestris pv. manihotis 280-95. Although greater xanthan production was observed after a 24h-alkali stress process, a lower viscosity was observed when compared to the alkali stress-free gum, regardless of the alkali stress time. However, this outcome is not conclusive as further studies on gum purification are required to remove excess sodium, verify the efficiency loss and the consequent increase in the polymer viscosity. Alkali stress altered the structure of xanthan gum from a polygon-like shape to a star-like form. At the end of the fermentation, early structural changes in the bacterium were observed. After alkali stress, marked structural differences were observed in the cells. A more vacuolated cytoplasm and discontinuities in the membrane cells evidenced the cell lysis. Xanthan was observed in the form of concentric circles instead of agglomerates as observed prior to the alkali stress. PMID:26887232

  5. Alkali-Metal Spin Maser.

    PubMed

    Chalupczak, W; Josephs-Franks, P

    2015-07-17

    Quantum measurement is a combination of a read-out and a perturbation of the quantum system. We explore the nonlinear spin dynamics generated by a linearly polarized probe beam in a continuous measurement of the collective spin state in a thermal alkali-metal atomic sample. We demonstrate that the probe-beam-driven perturbation leads, in the presence of indirect pumping, to complete polarization of the sample and macroscopic coherent spin oscillations. As a consequence of the former we report observation of spectral profiles free from collisional broadening. Nonlinear dynamics is studied through exploring its effect on radio frequency as well as spin noise spectra. PMID:26230788

  6. Mixed alkali effect on the spectroscopic properties of alkali-alkaline earth oxide borate glasses

    NASA Astrophysics Data System (ADS)

    Srinivas, G.; Ramesh, B.; Shareefuddin, Md.; Chary, M. N.; Sayanna, R.

    2016-05-01

    The mixed alkali and alkaline earth oxide borate glass with the composition xK2O - (25-x) Li2O-12.5BaO-12.5MgO-50B2O3 (x = 0, 5, 10, 15, 20 and 25mol %) and doped with 1mol% CuO were prepared by the melt quenching technique. From the optical absorption spectra the optical band gap, electronic polarizability(α02-), interaction parameter (A), theoretical and experimental optical basicity (Λ) values were evaluated. From the Electron Paramagnetic Resonance (EPR) spectral data the number of spins (N) and susceptibility (χ) were evaluated. The values of (α02-), and (Λ) increases with increasing of K2O content and electronic polarizability and interaction parameter show opposite behaviuor which may be due to the creation of non-bridging oxygens and expansion of borate network. The reciprocal of susceptibility (1/χ) and spin concentration (N) as a function of K2O content, varied nonlinearly which may be due to creation of non-bridging oxygens in the present glass system. This may be attributed to mixed alkali effect (MAE).

  7. An Alkali Metal-Capped Cerium(IV) Imido Complex.

    PubMed

    Solola, Lukman A; Zabula, Alexander V; Dorfner, Walter L; Manor, Brian C; Carroll, Patrick J; Schelter, Eric J

    2016-06-01

    Structurally authenticated, terminal lanthanide-ligand multiple bonds are rare and expected to be highly reactive. Even capped with an alkali metal cation, poor orbital energy matching and overlap of metal and ligand valence orbitals should result in strong charge polarization within such bonds. We expand on a new strategy for isolating terminal lanthanide-ligand multiple bonds using cerium(IV) complexes. In the current case, our tailored tris(hydroxylaminato) ligand framework, TriNOx(3-), provides steric protection against ligand scrambling and metal complex oligomerization and electronic protection against reduction. This strategy culminates in isolation of the first formal Ce═N bonded moiety in the complex [K(DME)2][Ce═N(3,5-(CF3)2C6H3)(TriNOx)], whose Ce═N bond is the shortest known at 2.119(3) Å. PMID:27163651

  8. Role of encapsulated metal cation in the reactivity and regioselectivity of the C₆₀ Diels-Alder reaction.

    PubMed

    Cui, Cheng-Xing; Liu, Ya-Jun

    2015-03-26

    Endohedral metallofullerene has novel properties because of the interaction between the encapsulated metal atom or cation and fullerene. Experiments have demonstrated that the insertion of Li(+) into C60 can greatly promote the reactivity of the Diels-Alder (DA) cycloaddition of cyclopentadiene (CpH) to C60. However, the reaction is sufficiently fast that its quantitative kinetic data cannot be obtained experimentally. In addition, knowledge regarding the effects of other alkali metal cations and metal cations with more charges on the reactivity and regioselectivity of C60 is almost nonexistent. In the current study, DA cycloadditions of CpH to M(+)@C60 (where M = Li, Na, K, Rb, and Cs) and Ca(2+)@C60 were investigated via density functional theory in the gas phase and in solvent. Via careful discussion and comparison with the results of C60, we concluded the following for the DA reaction of CpH to C60 and, more generally, for DA reactions of other fullerenes: (1) the encapsulated metal cations enhance the reactivity; (2) among alkali metal cations, Na(+) could be the best catalyst; (3) Ca(2+) is more favorable in promoting the reactivity than any alkali metal cation; (4) encapsulated metal cations with more positive charges enhance the reactivity of the 6-5 bond in C60, which is significant when the 6-5 adduct is the target product. PMID:25714730

  9. Crystal chemistry of hydrothermally grown ternary alkali rare earth fluorides.

    PubMed

    McMillen, Colin D; Comer, Sara; Fulle, Kyle; Sanjeewa, Liurukara D; Kolis, Joseph W

    2015-12-01

    The structural variations of several alkali metal rare earth fluoride single crystals are summarized. Two different stoichiometric formulations are considered, namely those of ARE2F7 and ARE3F10 (A = K, Rb, Cs; RE = Y, La-Lu), over a wide range of ionic radii of both the alkali and rare earth (RE) ions. Previously reported and several new single-crystal structures are considered. The new single crystals are grown using hydrothermal methods and the structures are compared with literature reports of structures grown from both melts and hydrothermal fluids. The data reported here are combined with the literature data to gain a greater understanding of structural subtleties surrounding these systems. The work underscores the importance of the size of the cations to the observed structure type and also introduces synthetic technique as a contributor to the same. New insights based on single-crystal structure analysis in the work introduce a new disordered structure type in the case of ARE2F7, and examine the trends and boundaries of the ARE3F10 stoichiometry. Such fundamental structural information is useful in understanding the potential applications of these compounds as optical materials. PMID:26634734

  10. Electronic excitation in bulk and nanocrystalline alkali halides.

    PubMed

    Bichoutskaia, Elena; Pyper, Nicholas C

    2012-11-14

    The lowest energy excitations in bulk alkali halides are investigated by considering five different excited state descriptions. It is concluded that excitation transfers one outermost halide electron in the fully ionic ground state to the lowest energy vacant s orbital of one closest cation neighbour to produce the excited state termed dipolar. The excitation energies of seven salts were computed using shell model description of the lattice polarization produced by the effective dipole moment of the excited state neutral halogen-neutral metal pair. Ab initio uncorrelated short-range inter-ionic interactions computed from anion wavefunctions adapted to the in-crystal environment were augmented by short-range electron correlation contributions derived from uniform electron-gas density functional theory. Dispersive attractions including wavefunction overlap damping were introduced using reliable semi-empirical dispersion coefficients. The good agreement between the predicted excitation energies and experiment provides strong evidence that the excited state is dipolar. In alkali halide nanocrystals in which each ionic plane contains only four ions, the Madelung energies are significantly reduced compared with the bulk. This predicts that the corresponding intra-crystal excitation energies in the nanocrystals, where there are two excited states depending on whether the halide electron is transferred to a cation in the same or in the neighbouring plane, will be reduced by almost 2 eV. For such an encapsulated KI crystal, it has been shown that the greater polarization in the excited state of the bulk crystal causes these reductions to be lowered to a 1.1 eV-1.5 eV range for the case of charge transfer to a neighbouring plane. For intra-plane charge transfer the magnitude of the polarization energy is further reduced thus causing the excitation in these encapsulated materials to be only 0.2 eV less than in the bulk crystal. PMID:23163361

  11. Method of handling radioactive alkali metal waste

    DOEpatents

    Wolson, Raymond D.; McPheeters, Charles C.

    1980-01-01

    Radioactive alkali metal is mixed with particulate silica in a rotary drum reactor in which the alkali metal is converted to the monoxide during rotation of the reactor to produce particulate silica coated with the alkali metal monoxide suitable as a feed material to make a glass for storing radioactive material. Silica particles, the majority of which pass through a 95 mesh screen or preferably through a 200 mesh screen, are employed in this process, and the preferred weight ratio of silica to alkali metal is 7 to 1 in order to produce a feed material for the final glass product having a silica to alkali metal monoxide ratio of about 5 to 1.

  12. Method of handling radioactive alkali metal waste

    DOEpatents

    Wolson, R.D.; McPheeters, C.C.

    Radioactive alkali metal is mixed with particulate silica in a rotary drum reactor in which the alkali metal is converted to the monoxide during rotation of the reactor to produce particulate silica coated with the alkali metal monoxide suitable as a feed material to make a glass for storing radioactive material. Silica particles, the majority of which pass through a 95 mesh screen or preferably through a 200 mesh screen, are employed in this process, and the preferred weight ratio of silica to alkali metal is 7 to 1 in order to produce a feed material for the final glass product having a silica to alkali metal monoxide ratio of about 5 to 1.

  13. Effect of alkali treatment on surface morphology of titanium

    SciTech Connect

    Tan, K. J. Wahab, M. A. A. Mahmod, S. Idris, M. I. Abdullah, H. Z.

    2015-07-22

    Alkali and heat treatments were first introduced by Kim et al. to prepare a bioactive surface on titanium. This method has been proven very effective and widely used in other studies to promote titanium osteointegration. This study aims to investigate further the effect of alkali treatment on surface morphology of high purity titanium. High purity titanium foils were immersed in NaOH aqueous solutions of 0.5 M, 5 M and 15 M at 60°C and 80 °C for 1, 3 and 7 days. The surface morphology was examined using Field Emission Scanning Electron Microscope (FESEM). The obtained phases were analysed using Fourier Transform Infrared Spectroscopy (FTIR) in the spectra range of 4000-600 cm{sup −1} at 4 cm{sup −1} resolution and 50 scans. At the same soaking temperature and soaking time, a thicker porous network was observed with increasing concentration of NaOH. At the same soaking temperature, a much porous structure was observed with increasing soaking time. At constant alkali concentration, more homogenously distributed porous surface structure was observed with increasing soaking temperature.

  14. The effects of potassium and rubidium hydroxide on the alkali-silica reaction

    SciTech Connect

    Shomglin, K.; Turanli, L.; Wenk, H.-R.; Monteiro, P.J.M.; Sposito, G

    2003-11-01

    Expansion of mortar specimens prepared with an aggregate of mylonite from the Santa Rosa mylonite zone in southern California was studied to investigate the effect of different alkali ions on the alkali-silica reaction in concrete. The expansion tests indicate that mortar has a greater expansion when subjected to a sodium hydroxide bath than in a sodium-potassium-rubidium hydroxide bath. Electron probe microanalysis (EPMA) of mortar bars at early ages show that rubidium ions, used as tracer, were present throughout the sample by the third day of exposure. The analysis also shows a high concentration of rubidium in silica gel from mortar bars exposed to bath solutions containing rubidium. The results suggest that expansion of mortar bars using ASTM C 1260 does not depend on the diffusion of alkali ions. The results indicate that the expansion of alkali-silica gel depends on the type of alkali ions present. Alkali-silica gel containing rubidium shows a lower concentration of calcium, suggesting competition for the same sites.

  15. Alkali metals in circulating fluidized bed combustion of biomass and coal: measurements and chemical equilibrium analysis

    SciTech Connect

    Michal P. Glazer; Nafees A. Khan; Wiebren de Jong; Hartmut Spliethoff; Heiko Schuermann; Penelope Monkhouse

    2005-10-01

    Combustion and co-combustion experiments with four kinds of straw, specially selected for their different alkali, Cl, and Si contents, and Colombian black coal were carried out in a circulating fluidized bed (CFB) reactor at Delft University of Technology. The influence of operating conditions and fuel composition on the release of the alkali compounds to the gas phase was investigated. The amount of the total gas-phase sodium and potassium compounds in the flue gases was measured with excimer laser induced fluorescence (ELIF). The results show that the release of gaseous alkali species depends on fuel composition, in particular the K/Cl and K/Si ratios in the fuel. The fuels with high K and Cl values show higher concentrations of the gaseous alkalis. A synergetic effect of the co-combustion with coal was observed, which led to a strong decrease in gaseous alkali concentrations. Together with experiments, chemical equilibrium modeling was performed to help in interpreting the experimental data. The calculations confirmed that the equilibrium is very strongly influenced by the composition of the fuel blend. Moreover, the simulations provided more information on sequestering of alkali species. 22 refs., 5 figs., 4 tabs.

  16. Synthesis and studies on microhardness of alkali zinc borate glasses

    NASA Astrophysics Data System (ADS)

    Subhashini, Bhattacharya, Soumalya; Shashikala, H. D.; Udayashankar, N. K.

    2014-04-01

    The mixed alkali effect on zinc borate glasses have been reported. The glass systems of nominal composition 10Zn+xLi2O+yNa2O+80B2O3 (x = y = 0, 5, 10, 15 mol%) were prepared using standard melt quenching method. The structural, physical and mechanical properties of the samples have been studied using X-ray diffraction(XRD), density measurement and Vickers hardness measurement, respectively. A consistent increase in the density was observed, which explains the role of the modifiers (Li2O and Na2O) in the network modification of borate structure. The molar volume is decreasing linearly with the alkali concentration, which is attributed to the conversion of tetrahedral boron (BO4/2)- into (BO3/2)-. The microhardness studies reveals the anisotropy nature of the material. It further confirms that the samples belong to hard glass category.

  17. Lattice strain across Na-K interdiffusion fronts in alkali feldspar: an electron back-scatter diffraction study

    NASA Astrophysics Data System (ADS)

    Schäffer, Anne-Kathrin; Jäpel, Tom; Zaefferer, Stefan; Abart, Rainer; Rhede, Dieter

    2014-11-01

    Cation exchange experiments between gem quality sanidine and KCl melt produced chemical alteration of alkali feldspar starting at the grain surface and propagating inwards by highly anisotropic Na-K interdiffusion on the alkali sublattice. Diffusion fronts developing in b-direction are very sharp, while diffusion fronts within the a- c-plane are comparatively broad. Due to the composition dependence of the lattice parameters of alkali feldspar, the diffusion induced compositional heterogeneity induces coherency stress and elastic strain. Electron back-scatter diffraction combined with the cross-correlation technique was employed to determine the lattice strain distribution across the Na-K interdiffusion fronts in partially exchanged single crystals of alkali feldspar. The strain changes gradually across the broad fronts within the a- c-plane, with a successive extension primarily in a-direction conferring to the composition strain in unstressed alkali feldspar. In contrast, lattice strain characterised by pronounced extension in b-direction is localised at the sharp diffusion fronts parallel to b, followed by a slight expansion in a-direction in the orthoclase-rich rim. This strain pattern does not confer with the composition induced lattice strain in a stress-free alkali feldspar. It may rather be explained by the mechanical coupling of the exchanged surface layer and the mechanically strong substratum. The lattice distortion localised at the sharp diffusion front may have an influence on the diffusion process and appears to produce a self-sharpening feedback, leading to a local reduction of component mobilities.

  18. Alkali burns from wet cement.

    PubMed Central

    Peters, W. J.

    1984-01-01

    When water is added to the dry materials of Portland cement calcium hydroxide is formed; the wet cement is caustic (with a pH as high as 12.9) and can produce third-degree alkali burns after 2 hours of contact. Unlike professional cement workers, amateurs are usually not aware of any danger and may stand or kneel in the cement for long periods. As illustrated in a case report, general physicians may recognize neither the seriousness of the injury in its early stages nor the significance of a history of prolonged contact with wet cement. All people working with cement should be warned about its dangers and advised to immediately wash and dry the skin if contact does occur. Images Fig. 1 PMID:6561052

  19. Cation Diffusivity and the Mixed Network Former Effect in Borosilicate Glasses.

    PubMed

    Smedskjaer, Morten M; Mauro, John C; Yue, Yuanzheng

    2015-06-11

    Understanding the structural origins of cationic diffusion processes in silicate glasses is important for high-tech applications of silicate glasses. For glasses with more than one network former, transport properties such as diffusivity are often nonlinear functions of the particular distribution of these network formers, a phenomenon known as the mixed network former effect. Here, we investigate the sodium-potassium interdiffusion (D̅Na-K) and the calcium inward diffusion (DCa) in soda lime borosilicate glasses with varying silica/borate ratio but constant modifier content. Indeed, the structural organization of borosilicate glasses results in a pronounced nonlinear composition dependence of D̅Na-K and DCa (i.e., the mixed network former effect). Initial addition of B2O3 to the glass system results in a significant decrease in both diffusivities, whereas the change in diffusivity per mole of added B2O3 decreases with increasing B2O3 concentration. Besides the influences of water content and atomic packing degree, we find that 99% of the composition dependence of log D̅Na-K can be ascribed to the change in concentration of tetrahedral boron groups. This indicates that the formation of BO4/2 groups slows down diffusion processes of alkali and alkaline earth ions. Therefore, the mixed network former effect of the studied glass series is linked with the change of the concentration of tetrahedral boron groups, which is caused by the interactions between the different types of network formers. PMID:25978700

  20. Evidence for anionic cation transport of lithium, sodium and potassium across the human erythrocyte membrane induced by divalent anions.

    PubMed Central

    Becker, B F; Duhm, J

    1978-01-01

    1. The passive net transport of Li+ and Na+ across the human red cell membrane was accelerated by the divalent anions carbonate, sulphite, oxalate, phosphite and malonate. Phthalate, maleate, sulphate and succinate were found additionally to stimulate downhill transport of K+. Marked differences in anion efficacy and selectivity were observed. 2. The effects of these 'carbonate type' anions were reversible and fully blocked by SITS, dipyridamole and other inhibitors of anion transfer. 3. Cation transport acceleration induced by the monovalent anions salicylate, benzoate, thiocyanate and 2,4-dinitrophenol were inhibited by dipyridamole, but not affected by SITS. A great number of mono- and polyvalent anions were without detectable influence on Li+ transport. 4. Li+ net uptake induced by oxalate exhibited a pH dependence similar to that reported for halide self exchange. 5. Transport acceleration by carbonate type anions displayed a linear, 1:1 dependence on the concentrations of both the anion and the cation and was symmetric with respect to the two sides of the membrane. 6. It is concluded that the divalent carbonate type anions form singly charged, negative 1:1 ion pairs with the respective alkali metal cations, the ion pairs traversing the red cell membrane via the anion exchange pathway. This concept of anionic formation of some of the ion pairs considered. The relative efficacies and cation selectivities of polyvalent anions can largely be explained on the basis of electrostatic interactions governing ion pair formation. However, the chelating properties, structural flexibility, polarizability of the anions and the accessibility of the ion pairs to the anion exchange pathway need also be considered. 7. An exchange of NaCO-3 ion pairs for internal HCO-3 or Cl- is discussed as a possible mode of cellular pH regulation. PMID:31458

  1. Integrating Sphere Alkali-Metal Vapor Cells

    NASA Astrophysics Data System (ADS)

    McGuyer, Bart; Ben-Kish, Amit; Jau, Yuan-Yu; Happer, William

    2010-03-01

    An integrating sphere is an optical multi-pass cavity that uses diffuse reflection to increase the optical path length. Typically applied in photometry and radiometry, integrating spheres have previously been used to detect trace gases and to cool and trap alkali-metal atoms. Here, we investigate the potential for integrating spheres to enhance optical absorption in optically thin alkali-metal vapor cells. In particular, we consider the importance of dielectric effects due to a glass container for the alkali-metal vapor. Potential applications include miniature atomic clocks and magnetometers, where multi-passing could reduce the operating temperature and power consumption.

  2. Alkali Silicate Vehicle Forms Durable, Fireproof Paint

    NASA Technical Reports Server (NTRS)

    Schutt, John B.; Seindenberg, Benjamin

    1964-01-01

    The problem: To develop a paint for use on satellites or space vehicles that exhibits high resistance to cracking, peeling, or flaking when subjected to a wide range of temperatures. Organic coatings will partially meet the required specifications but have the inherent disadvantage of combustibility. Alkali-silicate binders, used in some industrial coatings and adhesives, show evidence of forming a fireproof paint, but the problem of high surface-tension, a characteristic of alkali silicates, has not been resolved. The solution: Use of a suitable non-ionic wetting agent combined with a paint incorporating alkali silicate as the binder.

  3. Diode pumped alkali vapor fiber laser

    DOEpatents

    Payne, Stephen A.; Beach, Raymond J.; Dawson, Jay W.; Krupke, William F.

    2007-10-23

    A method and apparatus is provided for producing near-diffraction-limited laser light, or amplifying near-diffraction-limited light, in diode pumped alkali vapor photonic-band-gap fiber lasers or amplifiers. Laser light is both substantially generated and propagated in an alkali gas instead of a solid, allowing the nonlinear and damage limitations of conventional solid core fibers to be circumvented. Alkali vapor is introduced into the center hole of a photonic-band-gap fiber, which can then be pumped with light from a pump laser and operated as an oscillator with a seed beam, or can be configured as an amplifier.

  4. Diode pumped alkali vapor fiber laser

    DOEpatents

    Payne, Stephen A.; Beach, Raymond J.; Dawson, Jay W.; Krupke, William F.

    2006-07-26

    A method and apparatus is provided for producing near-diffraction-limited laser light, or amplifying near-diffraction-limited light, in diode pumped alkali vapor photonic-band-gap fiber lasers or amplifiers. Laser light is both substantially generated and propagated in an alkali gas instead of a solid, allowing the nonlinear and damage limitations of conventional solid core fibers to be circumvented. Alkali vapor is introduced into the center hole of a photonic-band-gap fiber, which can then be pumped with light from a pump laser and operated as an oscillator with a seed beam, or can be configured as an amplifier.

  5. Advancements in flowing diode pumped alkali lasers

    NASA Astrophysics Data System (ADS)

    Pitz, Greg A.; Stalnaker, Donald M.; Guild, Eric M.; Oliker, Benjamin Q.; Moran, Paul J.; Townsend, Steven W.; Hostutler, David A.

    2016-03-01

    Multiple variants of the Diode Pumped Alkali Laser (DPAL) have recently been demonstrated at the Air Force Research Laboratory (AFRL). Highlights of this ongoing research effort include: a) a 571W rubidium (Rb) based Master Oscillator Power Amplifier (MOPA) with a gain (2α) of 0.48 cm-1, b) a rubidium-cesium (Cs) Multi-Alkali Multi-Line (MAML) laser that simultaneously lases at both 795 nm and 895 nm, and c) a 1.5 kW resonantly pumped potassium (K) DPAL with a slope efficiency of 50%. The common factor among these experiments is the use of a flowing alkali test bed.

  6. Theoretical and experimental investigation of force imaging at the atomic scale on alkali halide crystals

    NASA Astrophysics Data System (ADS)

    Shluger, A. L.; Wilson, R. Mark; Williams, R. T.

    1994-02-01

    Assuming a model tip (Si4O10H10) as a reasonable representation of the surface of a Si3N4 cantilever stylus having a hydrogen-terminated asperity and a broader load-bearing base, we investigate the interaction of an atomic force microscope (AFM) with an alkali halide crystal by quantum chemical methods. Structural relaxation of the sample during engagement is allowed, and defect formation is investigated. Force curves above cation and anion positions are calculated, determining maximum sustainable loads and indicating a basis for atomic contrast. Experiments using a Si3N4 cantilever for AFM imaging of 12 alkali halide and alkaline earth fluoride crystals in air and desiccated helium are reported, in the widest AFM survey of such materials to date. Adsorbed water is shown to significantly enhance the observation of atomic periodicity on ionic halide samples, and rapid surface diffusion on alkali halide crystals is illustrated as it affects prospects for defect investigations. Observations of step edges and point-defect candidates at atomic scale are reported. The theoretical and experimental results are discussed together in the effort to provide a quantum-mechanical model for observations of alkali halide samples at atomic resolution, and to examine a possible basis for atomic resolution in the presence of long-range attractive forces.

  7. Alkali metal for ultraviolet band-pass filter

    NASA Technical Reports Server (NTRS)

    Mardesich, Nick (Inventor); Fraschetti, George A. (Inventor); Mccann, Timothy A. (Inventor); Mayall, Sherwood D. (Inventor); Dunn, Donald E. (Inventor); Trauger, John T. (Inventor)

    1993-01-01

    An alkali metal filter having a layer of metallic bismuth deposited onto the alkali metal is provided. The metallic bismuth acts to stabilize the surface of the alkali metal to prevent substantial surface migration from occurring on the alkali metal, which may degrade optical characteristics of the filter. To this end, a layer of metallic bismuth is deposited by vapor deposition over the alkali metal to a depth of approximately 5 to 10 A. A complete alkali metal filter is described along with a method for fabricating the alkali metal filter.

  8. The timing of alkali metasomatism in paleosols

    NASA Technical Reports Server (NTRS)

    MacFarlane, A. W.; Holland, H. D.

    1991-01-01

    We have measured the concentrations of rubidium and strontium and 87Sr/86Sr values of whole-rock samples from three paleosols of different ages. The oldest of the three weathering horizons, the 2,760 Ma Mt. Roe #1 paleosol in the Fortescue Group of Western Australia, experienced addition of Rb, and probably Sr, at 2,168 +/- 10 Ma. The intermediate paleosol, developed on the Hekpoort Basalt in South Africa, is estimated to have formed at 2,200 Ma, and yields a Rb-Sr isochron age of 1,925 +/- 32 Ma. The youngest of the three paleosols, developed on the Ongeluk basalt in Griqualand West, South Africa ca. 1,900 Ma, yielded a Rb-Sr age of 1,257 +/- 11 Ma. The Rb-Sr systematics of all three paleosols were reset during post-weathering metasomatism related to local or regional thermal disturbances. The Rb-Sr systematics of the paleosols were not subsequently disturbed. The near-complete removal of the alkali and alkaline earth elements from these paleosols during weathering made them particularly susceptible to resetting of their Rb-Sr systematics. Paleosols of this type are therefore sensitive indicators of the timing of thermal disturbances.

  9. Alkali Metal Handling Practices at NASA MSFC

    NASA Technical Reports Server (NTRS)

    Salvail, Patrick G.; Carter, Robert R.

    2002-01-01

    NASA Marshall Space Flight Center (MSFC) is NASA s principle propulsion development center. Research and development is coordinated and carried out on not only the existing transportation systems, but also those that may be flown in the near future. Heat pipe cooled fast fission cores are among several concepts being considered for the Nuclear Systems Initiative. Marshall Space Flight Center has developed a capability to handle high-purity alkali metals for use in heat pipes or liquid metal heat transfer loops. This capability is a low budget prototype of an alkali metal handling system that would allow the production of flight qualified heat pipe modules or alkali metal loops. The processing approach used to introduce pure alkali metal into heat pipe modules and other test articles are described in this paper.

  10. Alkali-metal intercalation in carbon nanotubes

    NASA Astrophysics Data System (ADS)

    Béguin, F.; Duclaux, L.; Méténier, K.; Frackowiak, E.; Salvetat, J. P.; Conard, J.; Bonnamy, S.; Lauginie, P.

    1999-09-01

    We report on successful intercalation of multiwall (MWNT) and single wall (SWNT) carbon nanotubes with alkali metals by electrochemical and vapor phase reactions. A LiC10 compound was produced by full electrochemical reduction of MWNT. KC8 and CsC8-MWNT first stage derivatives were synthesized in conditions of alkali vapor saturation. Their identity periods and the 2×2 R 0° alkali superlattice are comparable to their parent graphite compounds. The dysonian shape of KC8 EPR line and the temperature-independent Pauli susceptibility are both characteristic of a metallic behavior, which was confirmed by 13C NMR anisotropic shifts. Exposure of SWNT bundles to alkali vapor led to an increase of the pristine triangular lattice from 1.67 nm to 1.85 nm and 1.87 nm for potassium and rubidium, respectively.

  11. Ion chromatography with the indirect ultraviolet detection of alkali metal ions and ammonium using imidazolium ionic liquid as ultraviolet absorption reagent and eluent.

    PubMed

    Liu, Yong-Qiang; Yu, Hong

    2016-08-01

    Indirect ultraviolet detection was conducted in ultraviolet-absorption-agent-added mobile phase to complete the detection of the absence of ultraviolet absorption functional group in analytes. Compared with precolumn derivatization or postcolumn derivatization, this method can be widely used, has the advantages of simple operation and good linear relationship. Chromatographic separation of Li(+) , Na(+) , K(+) , and NH4 (+) was performed on a carboxylic acid base cation exchange column using imidazolium ionic liquid/acid/organic solvent as the mobile phase, in which imidazolium ionic liquids acted as ultraviolet absorption reagent and eluting agent. The retention behaviors of four kinds of cations are discussed, and the mechanism of separation and detection are described. The main factors influencing the separation and detection were the background ultraviolet absorption reagent and the concentration of hydrogen ion in the ion chromatography-indirect ultraviolet detection. The successful separation and detection of Li(+) , Na(+) , K(+) , and NH4 (+) within 13 min was achieved using the selected chromatographic conditions, and the detection limits (S/N = 3) were 0.02, 0.11, 0.30, and 0.06 mg/L, respectively. A new separation and analysis method of alkali metal ions and ammonium by ion chromatography with indirect ultraviolet detection method was developed, and the application range of ionic liquid was expanded. PMID:27377245

  12. ADSORPTION OF ORGANIC CATIONS TO NATURAL MATERIALS

    EPA Science Inventory

    The factors that control the extent of adsorption of amphiphilic organic cations on environmental and pristine surfaces have been studied. he sorbents were kaolinite, montmorillonite, two aquifer materials, and a soil; solutions contained various concentrations of NaCl and CaC12,...

  13. ADSORPTION OF ORGANIC CATIONS TO NATURAL MATERIALS

    EPA Science Inventory

    The factors that control the extent of adsorption of amphiphilic organic cations on environmental and pristine surfaces have been studied. The sorbents were kaolinite, montmorillonite, two aquifer materials, and a soil; solutions contained various concentrations of NaCl and CaCl,...

  14. Alkali metal intercalates of molybdenum disulfide.

    NASA Technical Reports Server (NTRS)

    Somoano, R. B.; Hadek, V.; Rembaum, A.

    1973-01-01

    Study of some of the physicochemical properties of compounds obtained by subjecting natural molybdenite and single crystals of molybdenum disulfide grown by chemical vapor transport to intercalation with the alkali group of metals (Li, Na, K, Rb, and Cs) by means of the liquid ammonia technique. Reported data and results include: (1) the intercalation of the entire alkali metal group, (2) stoichiometries and X-ray data on all of the compounds, and (3) superconductivity data for all the intercalation compounds.

  15. Superconductivity in alkali-doped C60

    NASA Astrophysics Data System (ADS)

    Ramirez, Arthur P.

    2015-07-01

    Superconductivity in alkali-doped C60 (A3C60, A = an alkali atom) is well described by an s-wave state produced by phonon mediated pairing. Moderate coupling of electrons to high-frequency shape-changing intra-molecular vibrational modes produces transition temperatures (Tc) up to 33 K in single-phase material. The good understanding of pairing in A3C60 offers a paradigm for the development of new superconducting materials.

  16. Desulfurizing Coal With an Alkali Treatment

    NASA Technical Reports Server (NTRS)

    Ravindram, M.; Kalvinskas, J. J.

    1987-01-01

    Experimental coal-desulfurization process uses alkalies and steam in fluidized-bed reactor. With highly volatile, high-sulfur bituminous coal, process removed 98 percent of pyritic sulfur and 47 percent of organic sulfur. Used in coal liquefaction and in production of clean solid fuels and synthetic liquid fuels. Nitrogen or steam flows through bed of coal in reactor. Alkalies react with sulfur, removing it from coal. Nitrogen flow fluidizes bed while heating or cooling; steam is fluidizing medium during reaction.

  17. Alkali metal crystalline polymer electrolytes.

    PubMed

    Zhang, Chuhong; Gamble, Stephen; Ainsworth, David; Slawin, Alexandra M Z; Andreev, Yuri G; Bruce, Peter G

    2009-07-01

    Polymer electrolytes have been studied extensively because uniquely they combine ionic conductivity with solid yet flexible mechanical properties, rendering them important for all-solid-state devices including batteries, electrochromic displays and smart windows. For some 30 years, ionic conductivity in polymers was considered to occur only in the amorphous state above Tg. Crystalline polymers were believed to be insulators. This changed with the discovery of Li(+) conductivity in crystalline poly(ethylene oxide)(6):LiAsF(6). However, new crystalline polymer electrolytes have proved elusive, questioning whether the 6:1 complex has particular structural features making it a unique exception to the rule that only amorphous polymers conduct. Here, we demonstrate that ionic conductivity in crystalline polymers is not unique to the 6:1 complex by reporting several new crystalline polymer electrolytes containing different alkali metal salts (Na(+), K(+) and Rb(+)), including the best conductor poly(ethylene oxide)(8):NaAsF(6) discovered so far, with a conductivity 1.5 orders of magnitude higher than poly(ethylene oxide)(6):LiAsF(6). These are the first crystalline polymer electrolytes with a different composition and structures to that of the 6:1 Li(+) complex. PMID:19543313

  18. Inter-domain electron transfer in cellobiose dehydrogenase: modulation by pH and divalent cations

    PubMed Central

    Kracher, Daniel; Zahma, Kawah; Schulz, Christopher; Sygmund, Christoph; Gorton, Lo; Ludwig, Roland

    2015-01-01

    The flavocytochrome cellobiose dehydrogenase (CDH) is secreted by wood-decomposing fungi, and is the only known extracellular enzyme with the characteristics of an electron transfer protein. Its proposed function is reduction of lytic polysaccharide mono-oxygenase for subsequent cellulose depolymerization. Electrons are transferred from FADH2 in the catalytic flavodehydrogenase domain of CDH to haem b in a mobile cytochrome domain, which acts as a mediator and transfers electrons towards the active site of lytic polysaccharide mono-oxygenase to activate oxygen. This vital role of the cytochrome domain is little understood, e.g. why do CDHs exhibit different pH optima and rates for inter-domain electron transfer (IET)? This study uses kinetic techniques and docking to assess the interaction of both domains and the resulting IET with regard to pH and ions. The results show that the reported elimination of IET at neutral or alkaline pH is caused by electrostatic repulsion, which prevents adoption of the closed conformation of CDH. Divalent alkali earth metal cations are shown to exert a bridging effect between the domains at concentrations of > 3 mm, thereby neutralizing electrostatic repulsion and increasing IET rates. The necessary high ion concentration, together with the docking results, show that this effect is not caused by specific cation binding sites, but by various clusters of Asp, Glu, Asn, Gln and the haem b propionate group at the domain interface. The results show that a closed conformation of both CDH domains is necessary for IET, but the closed conformation also increases the FAD reduction rate by an electron pulling effect. PMID:25913436

  19. Alkali content of alpine ultramafic rocks

    USGS Publications Warehouse

    Hamilton, W.; Mountjoy, W.

    1965-01-01

    The lower limit of abundance of sodium and potassium in ultramafic rocks is less than the threshold amount detectable by conventional analytical methods. By a dilutionaddition modification of the flame-spectrophotometric method, sodium and potassium have been determined in 40 specimens of alpine ultramafic rocks. Samples represent six regions in the United States and one in Australia, and include dunite, peridotite, pyroxenite, and their variably serpentinized and metamorphosed derivatives. The median value found for Na2O is 0.004 per cent, and the range of Na2O is 0.001-0.19. The median value for K2O is 0.0034 per cent and the range is 0.001-0.031 per cent. Alkali concentrations are below 0.01 per cent Na2O in 28 samples and below 0.01 per cent K2O in 35. Derivation of basalt magma from upper-mantle material similar to such ultramafic rocks, as has been postulated, is precluded by the relative amounts of sodium and potassium, which are from 200 to 600 times more abundant in basalt than in the ultramafic rocks. Similar factors apply to a number of other elements. No reasonable process could produce such concentrations in, for example, tens of thousands of cubic miles of uniform tholeiitic basalt. The ultramafic rocks might have originated either as magmatic crystal precipitates or as mantle residues left after fusion and removal of basaltic magma. Injection of ultramafic rocks to exposed positions is tectonic rather than magmatic. ?? 1965.

  20. Changes in the elastic moduli of C-S-H due to presence of interlaminar cations

    NASA Astrophysics Data System (ADS)

    Mejia, Shirley; Hoyos, Bibian

    2016-03-01

    A set of models of calcium silicate hydrate (C-S-H) with alkali cations in the interlaminar layer, various calcium/silicon ratios, and each with a density of 2.4 g cm-3 is presented. Using molecular simulation techniques, the objective was to study how the Young’s, bulk, and shear modulus, as well as the Poisson’s ratio changed due to the presence of monovalent ions. The effect of density on the elastic moduli was neglected, thus the NVT ensemble was used. Comparing the different simulation cells, it was found that models with sodium and potassium ions in the structure and an alkali/silicon ratio of 0.18 showed negative effects on the elastic moduli of C-S-H. This could be mainly ascribed to the shielding effect of the alkali on the interlaminar interactions that contribute to the cohesion between the layers of C-S-H.

  1. Heat capacity, glass transition temperature, size of cooperatively rearranging regions, and network connectivity of sodium silicate and alkali borate glasses

    SciTech Connect

    Borisova, N.V.; Ushakov, V.M.; Shultz, M.M.

    1994-07-01

    The radius of cooperatively rearranging domains at the glass transition in sodium silicate glasses and the number of bridging oxygen atoms in these domains are assessed within the framework of the kinetic theory of thermal fluctuations. The tendencies of the heat capacity, T{sub g}, and the cooperative rearrangement scale with the alkali oxide concentration in sodium silicate and alkali borate glasses are compared. The points of similarity and distinctions between them are revealed.

  2. Oxygen-consuming chlor alkali cell configured to minimize peroxide formation

    DOEpatents

    Chlistunoff, Jerzy B.; Lipp, Ludwig; Gottesfeld, Shimshon

    2006-08-01

    Oxygen-consuming zero gap chlor-alkali cell was configured to minimize peroxide formation. The cell included an ion-exchange membrane that divided the cell into an anode chamber including an anode and a cathode chamber including an oxygen gas diffusion cathode. The cathode included a single-piece of electrically conducting graphitized carbon cloth. Catalyst and polytetrafluoroethylene were attached to only one side of the cloth. When the cathode was positioned against the cation exchange membrane with the catalyst side away from the membrane, electrolysis of sodium chloride to chlorine and caustic (sodium hydroxide) proceeded with minimal peroxide formation.

  3. Coordination of trivalent metal cations to peptides: results from IRMPD spectroscopy and theory.

    PubMed

    Prell, James S; Flick, Tawnya G; Oomens, Jos; Berden, Giel; Williams, Evan R

    2010-01-21

    Structures of trivalent lanthanide metal cations La(3+), Ho(3+), and Eu(3+) with deprotonated Ala(n) (n = 2-5) or Leu-enk (Tyr-Gly-Gly-Phe-Leu) are investigated with infrared multiple photon dissociation (IRMPD) spectroscopy between 900 and 1850 cm(-1) and theory. In all of these complexes, a salt bridge is formed in which the metal cation coordinates to the carboxylate group of the peptide, resulting in a limited conformational space and many sharp IRMPD spectral bands. The IRMPD spectra clearly indicate that all carbonyl groups solvate the metal cation in each of the Ala(n) complexes. Due to strong vibrational coupling between the carbonyl groups, a sharp, high-energy amide I band due to in-phase stretching of all of the amide carbonyl groups bound to the metal cation is observed that is separated by approximately 50 cm(-1) from a strong, lower-energy amide I band. This extent of carbonyl coupling, which is sometimes observed in condensed-phase peptide and protein IR spectroscopy, has not been reported in IRMPD spectroscopy studies of other cationized peptide complexes. Intense bands due to carbonyl groups not associated with the metal cation are observed for Leu-enk complexes, indicating that a side chain group, such as the Tyr or Phe aromatic ring, prevents complete carbonyl coordination of the metal cation. Substitution of smaller lanthanide cations for La(3+) in these peptide complexes results only in minor structural changes consistent with the change in metal cation size. These are the first IRMPD spectra reported for lanthanide metal cationized peptides, and comparison to previously reported protonated and alkali metal or alkaline earth metal cationized peptide complexes reveals many trends consistent with the higher charge state of the lanthanide cations. PMID:19950916

  4. Complex formation of alkaline-earth cations with crown ethers and cryptands in methanol solutions

    SciTech Connect

    Buschman, H.J.

    1986-06-01

    The complexation of alkaline-earth cations by different crown ethers, azacrown ethers, and cryptands has been studied in methanol solutions by means of calorimetric and potentiometric titrations. The smallest monocyclic ligands examined from 2:1 complexes (ratio of ligand to cation) with cations which are too large to fit into the ligand cavity. With the smallest cryptand, only Sr/sup 2 +/ and Ba/sup 2 +/ ions are able to form exclusive complexes. In the case of the reaction of cryptand (211) with Ca/sup 2 +/, a separate estimation of stability constants for the formation of exclusive and inclusive complexes was possible for the first time. Higher values for stability constants are found for the reaction of alkaline-earth cations with cryptands compared to the reaction with alkali ions. This increase is only caused by favorable entropic contributions.

  5. Research on mouse model of grade II corneal alkali burn

    PubMed Central

    Bai, Jun-Qiang; Qin, Hai-Feng; Zhao, Shi-Hong

    2016-01-01

    AIM To choose appropriate concentration of sodium hydroxide (NaOH) solution to establish a stable and consistent corneal alkali burn mouse model in grade II. METHODS The mice (n=60) were randomly divided into four groups and 15 mice each group. Corneal alkali burns were induced by placing circle filter paper soaked with NaOH solutions on the right central cornea for 30s. The concentrations of NaOH solutions of groups A, B, C, and D were 0.1 mol/L, 0.15 mol/L, 0.2 mol/L, and 1.0 mol/L respectively. Then these corneas were irrigated with 20 mL physiological saline (0.9% NaCl). On day 7 postburn, slit lamp microscope was used to observe corneal opacity, corneal epithelial sodium fluorescein staining positive rate, incidence of corneal ulcer and corneal neovascularization, meanwhile pictures of the anterior eyes were taken. Cirrus spectral domain optical coherence tomography was used to scan cornea to observe corneal epithelial defect and corneal ulcer. RESULTS Corneal opacity scores (x±s) were not significantly different between the group A and group B (P=0.097). Incidence of corneal ulcer in group B was significantly higher than that in group A (P=0.035). Incidence of corneal ulcer and perforation rate in group B was lower than that in group C. Group C and D had corneal neovascularization, and incidence of corneal neovascularization in group D was significantly higher than that in group C (P=0.000). CONCLUSION Using 0.15 mol/L NaOH can establish grade II mouse model of corneal alkali burns. PMID:27162717

  6. Force Fields for Carbohydrate-Divalent Cation Interactions.

    PubMed

    Chen, Hsieh; Cox, Jason R; Panagiotopoulos, Athanassios Z

    2016-06-16

    We report molecular dynamics simulations to study intermolecular interactions for carbohydrate-divalent cation complexes. We observed that common force fields from literature with standard Lorentz-Berthelot combining rules are unable to reproduce the experimental stability constants for model carbohydrate monomer (α-d-Allopyranose) and alkali earth metal cation (Mg(2+), Ca(2+), Sr(2+), or Ba(2+)) complexes. A modified combining rule with rescaled effective cross-interaction radius between cations and the hydroxyl oxygens on the carbohydrates was introduced to reproduce the experimental stability constants, which the preferential carbohydrate-cation complexing structures through the ax-eq-ax sequence of O-1, O-2, and O-3 on α-d-Allopyranose were also observed. The effective radius scaling factor obtained from (α-d-Allopyranose)-Ca(2+) complexes was directly transferrable to the similar six-membered ring (α-d-Ribopyranose)-Ca(2+) complexes; however, reparameterization for the scaling factor may be necessary for the five-membered ring (α-d-Ribofuranose)-Ca(2+) complexes. PMID:27210229

  7. Crystal Structures of Three Framework Alkali Metal Uranyl Phosphate Hydrates

    NASA Astrophysics Data System (ADS)

    Locock, Andrew J.; Burns, Peter C.

    2002-08-01

    Three homeotypic hydrated alkali metal uranyl phosphates, A2(UO 2)[(UO 2)(PO 4)] 4(H 2O) 2, A=Cs ( CsUP), Rb ( RbUP), K ( KUP), were synthesized by hydrothermal methods. Intensity data were collected at room temperature using Mo Kα radiation and a CCD-based area detector. Their crystal structures were solved by Patterson ( CsUP) and direct ( RbUP, KUP) methods and refined by full-matrix least-squares techniques to agreement indices ( CsUP, RbUP, KUP) w R2=0.048, 0.230, 0.072 for all data, and R1=0.023, 0.078, 0.038 calculated for 5338, 4738, 4514 unique observed reflections (∣ Fo∣≥4 σF), respectively. The compound CsUP is orthorhombic, space group Cmc2 1, Z=4, a=14.854(1), b=13.879(1), c=12.987(1) Å, V=2677.5(3) Å 3. Both RbUP and KUP are monoclinic, space group Cm, but are presented in the unconventional pseudo-orthorhombic space group Fm11 to facilitate comparison with CsUP and to allow a model for RbUP that includes the effects of pseudo-merohedral twinning. RbUP is monoclinic, space group Fm11, Z=4, a=15.72(2), b=13.84(1), c=13.05(1) Å, α=90.39°(2), V=2839(5) Å 3; KUP is monoclinic, space group Fm11, Z=4, a=15.257(1), b=13.831(1), c=13.007(1) Å, α=91.760°(1), V=2743.4(3) Å 3. The structures consist of sheets of phosphate tetrahedra and uranyl pentagonal bipyramids, with composition [(UO 2)(PO 4)] -, that are topologically identical to the uranyl silicate sheets in uranophane-beta. These sheets are connected by a uranyl pentagonal bipyramid in the interlayer that shares corners with two phosphate tetrahedra on each of two adjacent sheets and whose fifth equatorial vertex is an H 2O group, resulting in an open framework with alkali metal cations in the larger cavities of the structures. Where CsUP and RbUP have two alkali metal positions and a H 2O group in these cavities, KUP has four K atoms and two H 2O groups, all of which are partially occupied, in the interstitial sites.

  8. Capture of alkali during pressurized fluidized-bed combustion using in-bed sorbents

    SciTech Connect

    Mann, M.D.; Ludlow, D.K.

    1997-12-31

    The primary focus of this research was the removal of alkali from PFBC flue gases to a level specified by turbine manufactures. The target level was less than 24 ppbw. Several of the aluminosilicate minerals have the potential to capture alkalis, especially sodium and potassium, under conditions typical of fluid-bed operation. Other goals of this work were to investigate the potential for simultaneously removing SO{sub 2} and Cl from the PFBC gas stream. The initial work focused primarily on one class of sorbents, sodalites, with the goal of determining whether sodalites can be used as an in-bed sorbent to simultaneously remove alkali and sulfur. Thermo gravimetric analysis (TGA) was used to study the mechanism of alkali capture using sodalite. Further testing was performed on a 7.6 cm (3-in.)-diameter pressurized fluid-bed reactor (PFBR). Early results indicated that simultaneous removal of alkali and sulfur and/or chlorine was not practical under the conditions for commercial PFBC operations. Therefore, the focus of the latter part of this work was on sorbents that have been shown to capture alkali in other systems. The effectiveness of bauxite and kaolinite to reduce vapor-phase alkali concentrations was determined. In addition to studying the gettering capability of the sorbent, the impact of the getter on operational performance was evaluated. This evaluation included examining potential agglomeration of bed particles, deposition on heat-transfer surfaces, and the bridging and blinding of ceramic candle filters. The focus of this paper is on the work performed on the PFBR.

  9. Cation-specific effects on enzymatic catalysis driven by interactions at the tunnel mouth.

    PubMed

    Štěpánková, Veronika; Paterová, Jana; Damborský, Jiří; Jungwirth, Pavel; Chaloupková, Radka; Heyda, Jan

    2013-05-30

    Cationic specificity which follows the Hofmeister series has been established for the catalytic efficiency of haloalkane dehalogenase LinB by a combination of molecular dynamics simulations and enzyme kinetic experiments. Simulations provided a detailed molecular picture of cation interactions with negatively charged residues on the protein surface, particularly at the tunnel mouth leading to the enzyme active site. On the basis of the binding affinities, cations were ordered as Na(+) > K(+) > Rb(+) > Cs(+). In agreement with this result, a steady-state kinetic analysis disclosed that the smaller alkali cations influence formation and productivity of enzyme-substrate complexes more efficiently than the larger ones. A subsequent systematic investigation of two LinB mutants with engineered charge in the cation-binding site revealed that the observed cation affinities are enhanced by increasing the number of negatively charged residues at the tunnel mouth, and vice versa, reduced by decreasing this number. However, the cation-specific effects are overwhelmed by strong electrostatic interactions in the former case. Interestingly, the substrate inhibition of the mutant LinB L177D in the presence of chloride salts was 7 times lower than that of LinB wild type in glycine buffer. Our work provides new insight into the mechanisms of specific cation effects on enzyme activity and suggests a potential strategy for suppression of substrate inhibition by the combination of protein and medium engineering. PMID:23627286

  10. Mechanical and microstructural properties of alkali-activated fly ash geopolymers.

    PubMed

    Komljenović, M; Bascarević, Z; Bradić, V

    2010-09-15

    This paper investigates the properties of geopolymer obtained by alkali-activation of fly ash (FA), i.e. the influence of characteristics of the representative group of FA (class F) from Serbia, as well as that of the nature and concentration of various activators on mechanical and microstructural properties of geopolymers. Aqueous solutions of Ca(OH)(2), NaOH, NaOH+Na(2)CO(3), KOH and sodium silicate (water glass) of various concentrations were used as alkali activators. It was established that the nature and concentration of the activator was the most dominant parameter in the alkali-activation process. In respect of physical characteristics of FA, the key parameter was fineness. The geopolymer based on FA with the highest content of fine particles (<43 microm), showed the highest compressive strength in all cases. Regardless of FA characteristics, nature and concentration of the activator, the alkali-activation products were mainly amorphous. The formation of crystalline phases (zeolites) occurred in some cases, depending on the reaction conditions. The highest compressive strength was obtained using sodium silicate. Together with the increase of sodium silicate SiO(2)/Na(2)O mass ratio, the atomic Si/Al ratio in the reaction products was also increased. Under the experimental conditions of this investigation, high strength was directly related to the high Si/Al ratio. PMID:20554110

  11. Alkali metal adsorption on Al(111)

    NASA Astrophysics Data System (ADS)

    Andersen, J. N.; Lundgren, E.; Nyholm, R.; Qvarford, M.

    1993-06-01

    The submonolayer adsorption of Na, K, Rb, and Cs on the Al(111) surface at 100 K and at room temperature is investigated by high resolution core level spectroscopy and low energy electron diffraction. It is found that the first alkali atoms on the surface adsorb at surface defects. At higher coverages, up to approximately one third of the maximum submonolayer coverage, alkali atoms adsorbed at defects coexist with a dispersed phase. At higher coverages island formation is found to occur for the majority of the systems. It is argued that all of the ordered structures formed at room temperature involve a disruption of the Al(111) surface in contrast to the situation at 100 K where the alkali atoms adsorb as adatoms.

  12. SAFE Alkali Metal Heat Pipe Reliability

    NASA Astrophysics Data System (ADS)

    Reid, Robert S.

    2003-01-01

    Alkali metal heat pipes are among the best understood and tested of components for first generation space fission reactors. A flight reactor will require production of a hundred or more heat pipes with assured reliability over a number of years. To date, alkali metal heat pipes have been built mostly in low budget development environments with little formal quality assurance. Despite this, heat pipe test samples suggest that high reliability can be achieved with the care justified for space flight qualification. Fabrication procedures have been established that, if consistently applied, ensure long-term trouble-free heat pipe operation. Alkali metal heat pipes have been successfully flight tested in micro gravity and also have been shown capable of multi-year operation with no evidence of sensitivity to fast neutron fluence up to 1023 n/cm2. This represents 50 times the fluence of the proposed Safe Affordable Fission Engine (SAFE-100) heat pipe reactor core.

  13. Visualization of alkali-denatured supercoiled plasmid DNA by atomic force microscopy

    SciTech Connect

    Yu Jia; Zhang Zhenfeng; Cao Kou; Huang Xitai

    2008-09-26

    To study the alkali denaturation of supercoiled DNA, plasmid pBR322 was treated with gradient concentrations of NaOH solution. The results of gel electrophoresis showed that the alkali denaturation of the supercoiled DNA occurred in a narrow range of pH value (12.88-12.90). The alkali-denatured supercoiled DNA ran, as a sharp band, faster than the supercoiled DNA. The supercoiled plasmid DNA of pBR322, pACYC184 and pJGX15A were denatured by NaOH, and then visualized by atomic force microscopy. Compared with the supercoiled DNA, the atomic force microscopy images of the alkali-denatured supercoiled DNA showed rough surface with many kinks, bulges on double strands with inhomogeneous diameters. The apparent contour lengths of the denatured DNA were shortened by 16%, 16% and 50% for pBR322, pACYC184 and pJGX15A, respectively. All evidence suggested that the alkali-denatured supercoiled DNA had a stable conformation with unregistered, topologically constrained double strands and intrastrand secondary structure.

  14. Diode pumped alkali lasers (DPALs): an overview

    NASA Astrophysics Data System (ADS)

    Krupke, William F.

    2008-05-01

    The concept of power-scalable, high beam-quality diode pumped alkali lasers was introduced in 2003 [Krupke, US Patent No. 6,643,311; Opt. Letters, 28, 2336 (2003)]. Since then several laboratory DPAL devices have been reported on, confirming many of the spectroscopic, kinetic, and laser characteristics projected from literature data. This talk will present an overview of the DPAL concept, summarize key relevant properties of the cesium, rubidium, and potassium alkali vapor gain media so-far examined, outline power scaling considerations, and highlight results of published DPAL laboratory experiments.

  15. Alkali metal vapors - Laser spectroscopy and applications

    NASA Technical Reports Server (NTRS)

    Stwalley, W. C.; Koch, M. E.

    1980-01-01

    The paper examines the rapidly expanding use of lasers for spectroscopic studies of alkali metal vapors. Since the alkali metals (lithium, sodium, potassium, rubidium and cesium) are theoretically simple ('visible hydrogen'), readily ionized, and strongly interacting with laser light, they represent ideal systems for quantitative understanding of microscopic interconversion mechanisms between photon (e.g., solar or laser), chemical, electrical and thermal energy. The possible implications of such understanding for a wide variety of practical applications (sodium lamps, thermionic converters, magnetohydrodynamic devices, new lasers, 'lithium waterfall' inertial confinement fusion reactors, etc.) are also discussed.

  16. Electron- and Photon-stimulated Desorption of Alkali Atoms from Lunar Sample and a Model Mineral Surface

    NASA Technical Reports Server (NTRS)

    Yakshinskiy, B. V.; Madey, T. E.

    2003-01-01

    We report recent results on an investigation of source mechanisms for the origin of alkali atoms in the tenuous planetary atmospheres, with focus on non-thermal processes (photon stimulated desorption (PSD), electron stimulated desorption (ESD), and ion sputtering). Whereas alkaline earth oxides (MgO, CaO) are far more abundant in lunar samples than alkali oxides (Na2O, K2O), the atmosphere of the Moon contains easily measurable concentrations of Na and K, while Ca and Mg are undetected there; traces of Ca have recently been seen in the Moon's atmosphere (10-3 of Na). The experiments have included ESD, PSD and ion sputtering of alkali atoms from model mineral surface (amorphous SiO2) and from a lunar basalt sample obtained from NASA. The comparison is made between ESD and PSD efficiency of monovalent alkalis (Na, K) and divalent alkaline earths (Ba, Ca).The ultrahigh vacuum measurement scheme for ESD and PSD of Na atoms includes a highly sensitive alkali metal detector based on surface ionization, and a time-of-flight technique. For PSD measurements, a mercury arc light source (filtered and chopped) is used. We find that bombardment of the alkali covered surfaces by ultraviolet photons or by low energy electrons (E>4 eV) causes desorption of hot alkali atoms. This results are consistent with the model developed to explain our previous measurements of sodium desorption from a silica surface and from water ice: electron- or photon-induced charge transfer from the substrate to the ionic adsorbate causes formation of a neutral alkali atom in a repulsive configuration, from which desorption occurs. The two-electron charge transfer to cause desorption of divalent alkaline eath ions is a less likely process.The data support the suggestion that PSD by UV solar photons is a dominant source process for alkalis in the tenuous lunar atmosphere.

  17. Solid-phase epitaxy of silicon amorphized by implantation of the alkali elements rubidium and cesium

    SciTech Connect

    Maier, R.; Haeublein, V.; Ryssel, H.; Voellm, H.; Feili, D.; Seidel, H.; Frey, L.

    2012-11-06

    The redistribution of implanted Rb and Cs profiles in amorphous silicon during solid-phase epitaxial recrystallization has been investigated by Rutherford backscattering spectroscopy and secondary ion mass spectroscopy. For the implantation dose used in these experiments, the alkali atoms segregate at the a-Si/c-Si interface during annealing resulting in concentration peaks near the interface. In this way, the alkali atoms are moved towards the surface. Rutherford backscattering spectroscopy in ion channeling configuration was performed to measure average recrystallization rates of the amorphous silicon layers. Preliminary studies on the influence of the alkali atoms on the solid-phase epitaxial regrowth rate reveal a strong retardation compared to the intrinsic recrystallization rate.

  18. Bond-length distributions for ions bonded to oxygen: alkali and alkaline-earth metals

    PubMed Central

    Gagné, Olivier Charles; Hawthorne, Frank Christopher

    2016-01-01

    Bond-length distributions have been examined for 55 configurations of alkali-metal ions and 29 configurations of alkaline-earth-metal ions bonded to oxygen, for 4859 coordination polyhedra and 38 594 bond distances (alkali metals), and for 3038 coordination polyhedra and 24 487 bond distances (alkaline-earth metals). Bond lengths generally show a positively skewed Gaussian distribution that originates from the variation in Born repulsion and Coulomb attraction as a function of interatomic distance. The skewness and kurtosis of these distributions generally decrease with increasing coordination number of the central cation, a result of decreasing Born repulsion with increasing coordination number. We confirm the following minimum coordination numbers: [3]Li+, [3]Na+, [4]K+, [4]Rb+, [6]Cs+, [3]Be2+, [4]Mg2+, [6]Ca2+, [6]Sr2+ and [6]Ba2+, but note that some reported examples are the result of extensive dynamic and/or positional short-range disorder and are not ordered arrangements. Some distributions of bond lengths are distinctly multi-modal. This is commonly due to the occurrence of large numbers of structure refinements of a particular structure type in which a particular cation is always present, leading to an over-representation of a specific range of bond lengths. Outliers in the distributions of mean bond lengths are often associated with anomalous values of atomic displacement of the constituent cations and/or anions. For a sample of [6]Na+, the ratio U eq(Na)/U eq(bonded anions) is partially correlated with 〈[6]Na+—O2−〉 (R 2 = 0.57), suggesting that the mean bond length is correlated with vibrational/displacement characteristics of the constituent ions for a fixed coordination number. Mean bond lengths also show a weak correlation with bond-length distortion from the mean value in general, although some coordination numbers show the widest variation in mean bond length for zero distortion, e.g. Li+ in [4]- and [6]-coordination, Na+ in [4]- and [6

  19. Bond-length distributions for ions bonded to oxygen: alkali and alkaline-earth metals.

    PubMed

    Gagné, Olivier Charles; Hawthorne, Frank Christopher

    2016-08-01

    Bond-length distributions have been examined for 55 configurations of alkali-metal ions and 29 configurations of alkaline-earth-metal ions bonded to oxygen, for 4859 coordination polyhedra and 38 594 bond distances (alkali metals), and for 3038 coordination polyhedra and 24 487 bond distances (alkaline-earth metals). Bond lengths generally show a positively skewed Gaussian distribution that originates from the variation in Born repulsion and Coulomb attraction as a function of interatomic distance. The skewness and kurtosis of these distributions generally decrease with increasing coordination number of the central cation, a result of decreasing Born repulsion with increasing coordination number. We confirm the following minimum coordination numbers: ([3])Li(+), ([3])Na(+), ([4])K(+), ([4])Rb(+), ([6])Cs(+), ([3])Be(2+), ([4])Mg(2+), ([6])Ca(2+), ([6])Sr(2+) and ([6])Ba(2+), but note that some reported examples are the result of extensive dynamic and/or positional short-range disorder and are not ordered arrangements. Some distributions of bond lengths are distinctly multi-modal. This is commonly due to the occurrence of large numbers of structure refinements of a particular structure type in which a particular cation is always present, leading to an over-representation of a specific range of bond lengths. Outliers in the distributions of mean bond lengths are often associated with anomalous values of atomic displacement of the constituent cations and/or anions. For a sample of ([6])Na(+), the ratio Ueq(Na)/Ueq(bonded anions) is partially correlated with 〈([6])Na(+)-O(2-)〉 (R(2) = 0.57), suggesting that the mean bond length is correlated with vibrational/displacement characteristics of the constituent ions for a fixed coordination number. Mean bond lengths also show a weak correlation with bond-length distortion from the mean value in general, although some coordination numbers show the widest variation in mean bond length for zero distortion, e.g. Li(+) in

  20. Alkali-aggregate reaction in concrete containing high-alkali cement and granite aggregate

    SciTech Connect

    Owsiak, Z

    2004-01-01

    The paper discusses results of the research into the influence of high-alkali Portland cement on granite aggregate. The deformation of the concrete structure occurred after 18 months. The research was carried out by means of a scanning electron microscope equipped with a high-energy dispersive X-ray analyzer that allowed observation of unpolished sections of concrete bars exhibiting the cracking pattern typical of the alkali-silica reaction. Both the microscopic observation and the X-ray elemental analysis confirm the presence of alkali-silica gel and secondary ettringite in the cracks.

  1. Water Content of Lunar Alkali Fedlspar

    NASA Technical Reports Server (NTRS)

    Mills, R. D.; Simon, J. I.; Wang, J.; Alexander, C. M. O'D.; Hauri, E. H.

    2016-01-01

    Detection of indigenous hydrogen in a diversity of lunar materials, including volcanic glass, melt inclusions, apatite, and plagioclase suggests water may have played a role in the chemical differentiation of the Moon. Spectroscopic data from the Moon indicate a positive correlation between water and Th. Modeling of lunar magma ocean crystallization predicts a similar chemical differentiation with the highest levels of water in the K- and Th-rich melt residuum of the magma ocean (i.e. urKREEP). Until now, the only sample-based estimates of water content of KREEP-rich magmas come from measurements of OH, F, and Cl in lunar apatites, which suggest a water concentration of < 1 ppm in urKREEP. Using these data, predict that the bulk water content of the magma ocean would have <10 ppm. In contrast, estimate water contents of 320 ppm for the bulk Moon and 1.4 wt % for urKREEP from plagioclase in ferroan anorthosites. Results and interpretation: NanoSIMS data from granitic clasts from Apollo sample 15405,78 show that alkali feldspar, a common mineral in K-enriched rocks, can have approx. 20 ppm of water, which implies magmatic water contents of approx. 1 wt % in the high-silica magmas. This estimate is 2 to 3 orders of magnitude higher than that estimated from apatite in similar rocks. However, the Cl and F contents of apatite in chemically similar rocks suggest that these melts also had high Cl/F ratios, which leads to spuriously low water estimates from the apatite. We can only estimate the minimum water content of urKREEP (+ bulk Moon) from our alkali feldspar data because of the unknown amount of degassing that led to the formation of the granites. Assuming a reasonable 10 to 100 times enrichment of water from urKREEP into the granites produces an estimate of 100-1000 ppm of water for the urKREEP reservoir. Using the modeling of and the 100-1000 ppm of water in urKREEP suggests a minimum bulk silicate Moon water content between 2 and 20 ppm. However, hydrogen loss was

  2. The use of some ion-exchange sorbing tracer cations in in-situ experiments in high saline groundwaters

    SciTech Connect

    Byegaard, J.; Skarnemark, G.; Skaalberg, M.

    1995-12-31

    The possibility to use alkali metals and alkaline earth metals as slightly sorbing tracers in in-situ sorption experiments in high saline groundwaters has been investigated. The cation exchange characteristics of granite and some fracture minerals (chlorite and calcite) have been studied using the proposed cations as tracers. The results show low Kd`s for Na, Ca and Sr ({approximately}0.1 ml/g), while the sorption is higher for the more electropositive cations (Rb, Cs and Ba). A higher contribution of irreversible sorption can also be observed for the latter group of cations. For calcite the sorption of all the tracers, except Ca, is lower compared to the corresponding sorption to granite and chlorite. Differences in selectivity coefficients and cation exchange capacity are obtained when using different size fractions of crushed granite. The difference is even more pronounced when comparing crushed granite to intact granite.

  3. Effect of basic alkali-pickling conditions on the production of lysinoalanine in preserved eggs.

    PubMed

    Zhao, Yan; Luo, Xuying; Li, Jianke; Xu, Mingsheng; Tu, Yonggang

    2015-09-01

    During the pickling process, strong alkali causes significant lysinoalanine (LAL) formation in preserved eggs, which may reduce the nutritional value of the proteins and result in a potential hazard to human health. In this study, the impacts of the alkali treatment conditions on the production of LAL in preserved eggs were investigated. Preserved eggs were prepared using different times and temperatures, and alkali-pickling solutions with different types and concentrations of alkali and metal salts, and the corresponding LAL contents were measured. The results showed the following: during the pickling period of the preserved egg, the content of LAL in the egg white first rapidly increased and then slowly increased; the content of LAL in the egg yolk continued to increase significantly. During the aging period, the levels of LAL in both egg white and egg yolk slowly increased. The amounts of LAL in the preserved eggs were not significantly different at temperatures between 20 and 25ºC. At higher pickling temperatures, the LAL content in the preserved eggs increased. With the increase of alkali concentration in the alkali-pickling solution, the LAL content in the egg white and egg yolk showed an overall trend of an initial increase followed by a slight decrease. The content of LAL produced in preserved eggs treated with KOH was lower than in those treated with NaOH. NaCl and KCl produced no significant effects on the production of LAL in the preserved eggs. With increasing amounts of heavy metal salts, the LAL content in the preserved eggs first decreased and then increased. The LAL content generated in the CuSO4 group was lower than that in either the ZnSO4 or PbO groups. PMID:26188034

  4. Adsorption of reovirus to clay minerals: effects of cation-exchange capacity, cation saturation, and surface area.

    PubMed Central

    Lipson, S M; Stotzky, G

    1983-01-01

    The adsorption of reovirus to clay minerals has been reported by several investigators, but the mechanisms defining this association have been studied only minimally. The purpose of this investigation was to elucidate the mechanisms involved with this interaction. More reovirus type 3 was adsorbed, in both distilled and synthetic estuarine water, by low concentrations of montmorillonite than by comparable concentrations of kaolinite containing a mixed complement of cations on the exchange complex. Adsorption to the clays was essentially immediate and was correlated with the cation-exchange capacity of the clays, indicating that adsorption was primarily to negatively charged sites on the clays. Adsorption was greater with low concentrations of clays in estuarine water than in distilled water, as the higher ionic strength of the estuarine water reduced the electrokinetic potential of both clay and virus particles. The addition of cations (as chloride salts) to distilled water enhanced adsorption, with divalent cations being more effective than monovalent cations and 10(-2) M resulting in more adsorption than 10(-3) M. Potassium ions suppressed reovirus adsorption to montmorillonite, probably by collapsing the clay lattices and preventing the expression of the interlayer-derived cation-exchange capacity. More virus was adsorbed by montmorillonite made homoionic to various mono-, di-, and trivalent cations (except by montmorillonite homoionic to potassium) than by comparable concentrations of kaolinite homoionic to the same cations. The sequence of the amount of adsorption to homoionic montmorillonite was Al greater than Ca greater than Mg greater than Na greater than K; the sequence of adsorption to kaolinite was Na greater than Al greater than Ca greater than Mg greater than K. The constant partition-type adsorption isotherms obtained when the clay concentration was maintained constant and the virus concentration was varied indicated that a fixed proportion of the

  5. Faraday rotation density measurements of optically thick alkali metal vapors

    NASA Astrophysics Data System (ADS)

    Vliegen, E.; Kadlecek, S.; Anderson, L. W.; Walker, T. G.; Erickson, C. J.; Happer, William

    2001-03-01

    We investigate the measurement of alkali number densities using the Faraday rotation of linearly polarized light. We find that the alkali number density may be reliably extracted even in regimes of very high buffer gas pressure, and very high alkali number density. We have directly verified our results in potassium using absorption spectroscopy on the second resonance (4 2S→5 2P).

  6. 40 CFR 721.1878 - Alkali metal alkyl borohydride (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Alkali metal alkyl borohydride... Specific Chemical Substances § 721.1878 Alkali metal alkyl borohydride (generic). (a) Chemical substance... alkali metal alkyl borohydride (PMN P-00-1089) is subject to reporting under this section for...

  7. 40 CFR 721.1878 - Alkali metal alkyl borohydride (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Alkali metal alkyl borohydride... Specific Chemical Substances § 721.1878 Alkali metal alkyl borohydride (generic). (a) Chemical substance... alkali metal alkyl borohydride (PMN P-00-1089) is subject to reporting under this section for...

  8. 40 CFR 721.1878 - Alkali metal alkyl borohydride (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Alkali metal alkyl borohydride... Specific Chemical Substances § 721.1878 Alkali metal alkyl borohydride (generic). (a) Chemical substance... alkali metal alkyl borohydride (PMN P-00-1089) is subject to reporting under this section for...

  9. 40 CFR 721.1878 - Alkali metal alkyl borohydride (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Alkali metal alkyl borohydride... Specific Chemical Substances § 721.1878 Alkali metal alkyl borohydride (generic). (a) Chemical substance... alkali metal alkyl borohydride (PMN P-00-1089) is subject to reporting under this section for...

  10. 40 CFR 721.4660 - Alcohol, alkali metal salt.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Alcohol, alkali metal salt. 721.4660... Substances § 721.4660 Alcohol, alkali metal salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as alcohol, alkali metal salt (PMN P-91-151)...

  11. 40 CFR 721.4660 - Alcohol, alkali metal salt.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Alcohol, alkali metal salt. 721.4660... Substances § 721.4660 Alcohol, alkali metal salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as alcohol, alkali metal salt (PMN P-91-151)...

  12. 40 CFR 721.4660 - Alcohol, alkali metal salt.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Alcohol, alkali metal salt. 721.4660... Substances § 721.4660 Alcohol, alkali metal salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as alcohol, alkali metal salt (PMN P-91-151)...

  13. 40 CFR 721.4660 - Alcohol, alkali metal salt.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Alcohol, alkali metal salt. 721.4660... Substances § 721.4660 Alcohol, alkali metal salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as alcohol, alkali metal salt (PMN P-91-151)...

  14. 40 CFR 721.4660 - Alcohol, alkali metal salt.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Alcohol, alkali metal salt. 721.4660... Substances § 721.4660 Alcohol, alkali metal salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as alcohol, alkali metal salt (PMN P-91-151)...

  15. 40 CFR 721.5278 - Substituted naphthalenesulfonic acid, alkali salt.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ..., alkali salt. 721.5278 Section 721.5278 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.5278 Substituted naphthalenesulfonic acid, alkali salt. (a) Chemical... as a substituted naphthalenesulfonic acid, alkali salt (PMN P-95-85) is subject to reporting...

  16. 40 CFR 721.8900 - Substituted halogenated pyridinol, alkali salt.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ..., alkali salt. 721.8900 Section 721.8900 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.8900 Substituted halogenated pyridinol, alkali salt. (a) Chemical... as substituted halogenated pyridinols, alkali salts (PMNs P-88-1271 and P-88-1272) are subject...

  17. 40 CFR 721.5278 - Substituted naphthalenesulfonic acid, alkali salt.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., alkali salt. 721.5278 Section 721.5278 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.5278 Substituted naphthalenesulfonic acid, alkali salt. (a) Chemical... as a substituted naphthalenesulfonic acid, alkali salt (PMN P-95-85) is subject to reporting...

  18. 40 CFR 721.8900 - Substituted halogenated pyridinol, alkali salt.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., alkali salt. 721.8900 Section 721.8900 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.8900 Substituted halogenated pyridinol, alkali salt. (a) Chemical... as substituted halogenated pyridinols, alkali salts (PMNs P-88-1271 and P-88-1272) are subject...

  19. 40 CFR 721.5278 - Substituted naphthalenesulfonic acid, alkali salt.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., alkali salt. 721.5278 Section 721.5278 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.5278 Substituted naphthalenesulfonic acid, alkali salt. (a) Chemical... as a substituted naphthalenesulfonic acid, alkali salt (PMN P-95-85) is subject to reporting...

  20. 40 CFR 721.5278 - Substituted naphthalenesulfonic acid, alkali salt.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ..., alkali salt. 721.5278 Section 721.5278 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.5278 Substituted naphthalenesulfonic acid, alkali salt. (a) Chemical... as a substituted naphthalenesulfonic acid, alkali salt (PMN P-95-85) is subject to reporting...

  1. 40 CFR 721.5278 - Substituted naphthalenesulfonic acid, alkali salt.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., alkali salt. 721.5278 Section 721.5278 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.5278 Substituted naphthalenesulfonic acid, alkali salt. (a) Chemical... as a substituted naphthalenesulfonic acid, alkali salt (PMN P-95-85) is subject to reporting...

  2. Computational studies of solid-state alkali conduction in rechargeable alkali-ion batteries

    DOE PAGESBeta

    Deng, Zhi; Mo, Yifei; Ong, Shyue Ping

    2016-03-25

    The facile conduction of alkali ions in a crystal host is of crucial importance in rechargeable alkali-ion batteries, the dominant form of energy storage today. In this review, we provide a comprehensive survey of computational approaches to study solid-state alkali diffusion. We demonstrate how these methods have provided useful insights into the design of materials that form the main components of a rechargeable alkali-ion battery, namely the electrodes, superionic conductor solid electrolytes and interfaces. We will also provide a perspective on future challenges and directions. Here, the scope of this review includes the monovalent lithium- and sodium-ion chemistries that aremore » currently of the most commercial interest.« less

  3. Alkali resistant optical coatings for alkali lasers and methods of production thereof

    DOEpatents

    Soules, Thomas F; Beach, Raymond J; Mitchell, Scott C

    2014-11-18

    In one embodiment, a multilayer dielectric coating for use in an alkali laser includes two or more alternating layers of high and low refractive index materials, wherein an innermost layer includes a thicker, >500 nm, and dense, >97% of theoretical, layer of at least one of: alumina, zirconia, and hafnia for protecting subsequent layers of the two or more alternating layers of high and low index dielectric materials from alkali attack. In another embodiment, a method for forming an alkali resistant coating includes forming a first oxide material above a substrate and forming a second oxide material above the first oxide material to form a multilayer dielectric coating, wherein the second oxide material is on a side of the multilayer dielectric coating for contacting an alkali.

  4. MLKL forms cation channels

    PubMed Central

    Xia, Bingqing; Fang, Sui; Chen, Xueqin; Hu, Hong; Chen, Peiyuan; Wang, Huayi; Gao, Zhaobing

    2016-01-01

    The mixed lineage kinase domain-like (MLKL) protein is a key factor in tumor necrosis factor-induced necroptosis. Recent studies on necroptosis execution revealed a commitment role of MLKL in membrane disruption. However, our knowledge of how MLKL functions on membrane remains very limited. Here we demonstrate that MLKL forms cation channels that are permeable preferentially to Mg2+ rather than Ca2+ in the presence of Na+ and K+. Moreover, the N-terminal domain containing six helices (H1-H6) is sufficient to form channels. Using the substituted cysteine accessibility method, we further determine that helix H1, H2, H3, H5 and H6 are transmembrane segments, while H4 is located in the cytoplasm. Finally, MLKL-induced membrane depolarization and cell death exhibit a positive correlation to its channel activity. The Mg2+-preferred permeability and five transmembrane segment topology distinguish MLKL from previously identified Mg2+-permeable channels and thus establish MLKL as a novel class of cation channels. PMID:27033670

  5. Terahertz radiation in alkali vapor plasmas

    SciTech Connect

    Sun, Xuan; Zhang, X.-C.

    2014-05-12

    By taking advantage of low ionization potentials of alkali atoms, we demonstrate terahertz wave generation from cesium and rubidium vapor plasmas with an amplitude nearly one order of magnitude larger than that from nitrogen gas at low pressure (0.02–0.5 Torr). The observed phenomena are explained by the numerical modeling based upon electron tunneling ionization.

  6. The Additive Coloration of Alkali Halides

    ERIC Educational Resources Information Center

    Jirgal, G. H.; and others

    1969-01-01

    Describes the construction and use of an inexpensive, vacuum furnace designed to produce F-centers in alkali halide crystals by additive coloration. The method described avoids corrosion or contamination during the coloration process. Examination of the resultant crystals is discussed and several experiments using additively colored crystals are…

  7. Influence of lithium hydroxide on alkali-silica reaction

    SciTech Connect

    Bulteel, D.; Garcia-Diaz, E.; Degrugilliers, P.

    2010-04-15

    Several papers show that the use of lithium limits the development of alkali-silica reaction (ASR) in concrete. The aim of this study is to improve the understanding of lithium's role on the alteration mechanism of ASR. The approach used is a chemical method which allowed a quantitative measurement of the specific degree of reaction of ASR. The chemical concrete sub-system used, called model reactor, is composed of the main ASR reagents: reactive aggregate, portlandite and alkaline solution. Different reaction degrees are measured and compared for different alkaline solutions: NaOH, KOH and LiOH. Alteration by ASR is observed with the same reaction degrees in the presence of NaOH and KOH, accompanied by the consumption of hydroxyl concentration. On the other hand with LiOH, ASR is very limited. Reaction degree values evolve little and the hydroxyl concentration remains about stable. These observations demonstrate that lithium ions have an inhibitor role on ASR.

  8. Hyaline membrane disease, alkali, and intraventricular haemorrhage.

    PubMed Central

    Wigglesworth, J S; Keith, I H; Girling, D J; Slade, S A

    1976-01-01

    The relation between intraventricular haemorrhage (IVH) and hyaline membrane disease (HMD) was studied in singletons that came to necropsy at Hammersmith Hospital over the years 1966-73. The incidence of IVH in singleton live births was 3-22/1000 and of HMD 4-44/1000. Although the high figures were partily due to the large number of low birthweight infants born at this hospital, the incidence of IVH in babies weighing 1001-1500 g was three times as great as that reported in the 1658 British Perinatal Mortality Survey. Most IVH deaths were in babies with HMD, but the higher frequency of IVH was not associated with any prolongation of survival time of babies who died with HMD as compared with the 1958 survey. IVH was seen frequently at gestations of up to 36 weeks in babies with HMD but was rare above 30 weeks' gestation in babies without HMD. This indicated that factors associated with HMD must cause most cases of IVH seen at gestations above 30 weeks. Comparison of clinical details in infants with HMD who died with or without IVH (at gestations of 30-37 weeks) showed no significant differences between the groups other than a high incidence of fits and greater use of alkali therapy in the babies with IVH. During the 12 hours when most alkali therapy was given, babies dying with IVD received a mean total alkali dosage of 10-21 mmol/kg and those dying without IVH 6-34 mmol/kg (P less than 0-001).There was no difference in severity of hypoxia or of metabolic acidosis between the 2 groups. Babies who died with HMD and germinal layer haemorrhage (GLH) without IVH had received significantly more alkali than those who died with HMD alone, whereas survivors of severe respiratory distress syndrome had received lower alkali doses than other groups. It is suggested that the greatly increased death rate from IVH in babies with HMD indicates some alteration of management of HMD (since 1958) as a causative factor. Liberal use of hypertonic alkali solutions is the common factor

  9. Self-assembly of Alkali-uranyl-peroxide Clusters

    SciTech Connect

    Nyman, May; Rodriquez, Mark A.; Campana, Charles F.

    2010-08-11

    The hexavalent uranium specie, uranyl triperoxide, UO2(O2)34-, has been shown recently to behave like high oxidation-state d0 transition-metals, self-assembling into polyoxometalate-like clusters that contain up to 60 uranyl cations bridged by peroxide ligands. There has been much less focus on synthesis and structural characterization of salts of the monomeric UO2(O2)34- building block of these clusters. However, these could serve as water-soluble uranyl precursors for both clusters and materials, and also be used as simple models to study aqueous behavior by experiment and modeling. The countercation is of utmost importance to the assembly of these clusters, and Li+ has proven useful for the crystallization of many of the known cluster geometries to date. We present in this paper synthesis and structural characterization of two monomeric lithium uranyl-peroxide salts, Li4[UO2(O2)3]·10H2O (1) and [UO2(O2)3]12[(UO2(OH)4)Li16(H2O)28]3·Li6[H2O]26 (2). They were obtained from aqueous-alcohol solutions rather than the analogous aqueous solutions from which lithium uranyl-peroxide clusters are crystallized. Rapid introduction of the alcohol gives the structure of (1) whereas slow diffusion of alcohol results in crystallization of (2). (2) is an unusual structure featuring uranyl-centered alkali clusters that are linked into ring and spherical arrangements via [UO2(O2)3] anions. Furthermore, partial substitution of Rb or Cs into the synthesis results in formation of (2) with substitution of these larger alkalis into the uranyl-centered clusters. We surmise that the slow crystallization allows for direct bonding of alkali metals to the

  10. Alkali gabbronorite, ultra-KREEPy melt rock and the diverse suite of clasts in North Ray crater feldspathic fragmental breccia 67975

    SciTech Connect

    Lindstrom, M.M.

    1984-11-15

    Lunar breccia 67975 is a feldspathic fragmental breccia from North Ray crater, Apollo 16. It contains clasts of alkali gabbronorite and ultra-KREEPy mafic fragment-laden melt breccias, which are unique among Apollo 16 samples. Both are alkali- and iron-rich rocks with moderate to high REE concentrations. They more strongly resemble Apollo 14 gabbronorites and alkali anorthosites and KREEP-rich rocks than they do other Apollo 16 samples. The other clasts in 67975 are the ferroan anorthosites, feldspathic melt rocks, and magnesian granulites, which are typical of other feldspathic fragmental breccias. Examination of bulk and mineral compositions of other breccias and melt rocks suggests that alkali gabbronorite may be a minor component in other North Ray crater breccias and feldspathic melt rocks. This implies that alkali gabbronorite was a fairly early (4.0 b.y.) crustal component in the North Ray crater region.

  11. The relation between net calcium, alkali cation and chloride movements in red cells exposed to salicylate.

    PubMed Central

    Bürgin, H; Schatzmann, H J

    1979-01-01

    1. From a 150 mM-NH4 salicylate medium salicylate enters human red cells with a rate constant of 1.9 min-1 at 0 degrees C. 2. Salicylate increases the red cell permeability for Ca2+ (and Mg2+). There is no saturation of the Ca2+ transfer with respect to salicylate up to 150 mM and with respect to external Ca2+ up to 30 mM. 3. Ca2+ entering from salicylate media activates the Ca-sensitive K channel present in human but not in adult ruminant red cells. 4. The increase in K permeability which ensues hyperpolarizes the membrane in Na salicylate media, accelerating further Ca2+ entry and Mg2+ entry and favouring Cl- loss (see Fig. 8). The Ca2+ inward movement is in agreement with the constant field equation if the membrane potential is assumed to equal the K equilibrium potential and if two charges are attributed to the mobile species. 5. The effect of salicylate on Ca2+ permeability and hence its sequelae are reversible upon washing the cells. 6. 3-OH-benzoic acid and 4-OH-benzoic acid do not exert the effect salicylate has on Ca2+ permeability. 7. In 150 mM-Na salicylate media the Cl--salicylate exchange is virtually nil at 0 degrees C. The exchange seen at 19 degrees C is obviously not across the anion exchange mechanism and proceeds at a rate comparable to that for Cl- movement in the nonexchange-restricted mode given by Hunter (1971, 1977) for cells in a normal medium. 8. Ca2+ seems to increase the Cl- permeability seen under these conditions. 9. The possibility that salicylate acts as an ionophore for Ca2+ is discussed. PMID:430388

  12. Optical probes for the detection of protons, and alkali and alkaline earth metal cations.

    PubMed

    Hamilton, Graham R C; Sahoo, Suban K; Kamila, Sukanta; Singh, Narinder; Kaur, Navneet; Hyland, Barry W; Callan, John F

    2015-07-01

    Luminescent sensors and switches continue to play a key role in shaping our understanding of key biochemical processes, assist in the diagnosis of disease and contribute to the design of new drugs and therapies. Similarly, their contribution to the environment cannot be understated as they offer a portable means to undertake field testing for hazardous chemicals and pollutants such as heavy metals. From a physiological perspective, the Group I and II metal ions are among the most important in the periodic table with blood plasma levels of H(+), Na(+) and Ca(2+) being indicators of several possible disease states. In this review, we examine the progress that has been made in the development of luminescent probes for Group I and Group II ions as well as protons. The potential applications of these probes and the mechanism involved in controlling their luminescent response upon analyte binding will also be discussed. PMID:25742963

  13. POTENTIAL-MODULATED INTERCALATION OF ALKALI CATIONS INTO METAL HEXACYANOFERRATE COATED ELECTRODES

    EPA Science Inventory

    The current baseline technology for separating radiocesium (137Cs) from liquid wastes is traditional ion exchange, where chemical regeneration of the ion exchange bed can generate many bed volumes of secondary rinse and regeneration waste solution during each exchange cycle. Chem...

  14. Novel Pendant Benzene Disulfonic Acid Blended SPPO Membranes for Alkali Recovery: Fabrication and Properties.

    PubMed

    Mondal, Abhishek N; Dai, Chunhua; Pan, Jiefeng; Zheng, Chunlei; Hossain, Md Masem; Khan, Muhammad Imran; Wu, Liang; Xu, Tongwen

    2015-07-29

    To reconcile the trade-off between separation performance and availability of desired material for cation exchange membranes (CEMs), we designed and successfully prepared a novel sulfonated aromatic backbone-based cation exchange precursor named sodium 4,4'-(((((3,3'-disulfo-[1,1'-biphenyl]-4,4'-diyl)bis(oxy)) bis(4,1-phenylene))bis(azanediyl))bis(methylene))bis(benzene-1,3-disulfonate) [DSBPB] from 4,4'-bis(4-aminophenoxy)-[1,1'-biphenyl]-3,3'-disulfonic acid [BAPBDS] by a three-step procedure that included sulfonation, Michael condensation followed by reduction. Prepared DSBPB was used to blend with sulfonated poly(2,6-dimethyl-1,4-phenylene oxide) (SPPO) to get CEMs for alkali recovery via diffusion dialysis. Physiochemical properties and electrochemical performance of prepared membranes can be tuned by varying the dosage of DSBPB. All the thermo-mechanical properties like DMA and TGA were investigated along with water uptake (WR), ion exchange capacity (IEC), dimensional stability, etc. The effect of DSBPB was discussed in brief in connection with alkali recovery and ion conducting channels. The SPPO/DSBPB membranes possess both high water uptake as well as ion exchange capacity with high thermo-mechanical stability. At 25 °C the dialysis coefficients (UOH) appeared to be in the range of 0.0048-0.00814 m/h, whereas the separation factor (S) ranged from 12.61 to 36.88 when the membranes were tested for base recovery in Na2WO4/NaOH waste solution. Prepared membranes showed much improved DD performances compared to traditional SPPO membrane and possess the potentiality to be a promising candidate for alkali recovery via diffusion dialysis. PMID:26146932

  15. Physics and chemistry of alkali-silica reactions

    SciTech Connect

    Diamond, S.; Barneyback, R.S. Jr.; Struble, L.J.

    1981-01-01

    The philosophy underlying recent research on alkali-silica reactions is reviewed and illustrations of recent results are provided. It has been possible to follow the kinetics of the chemical reaction between dissolved alkalis and opal in mortars by monitoring the rate at which alkalis are removed from the pore solutions of reacting mortars. Studies of the expansion behavior of synthetic alkali silica gels under controlled conditions were carried out and show no obvious correlation to chemical composition. The alkali reaction in mortars was found to produce changes in the appearance of opal grains documentable by the use of a scanning electron microscope.

  16. Calcium-Alkali Syndrome in the Modern Era

    PubMed Central

    Patel, Ami M.; Adeseun, Gbemisola A.; Goldfarb, Stanley

    2013-01-01

    The ingestion of calcium, along with alkali, results in a well-described triad of hypercalcemia, metabolic alkalosis, and renal insufficiency. Over time, the epidemiology and root cause of the syndrome have shifted, such that the disorder, originally called the milk-alkali syndrome, is now better described as the calcium-alkali syndrome. The calcium-alkali syndrome is an important cause of morbidity that may be on the rise, an unintended consequence of shifts in calcium and vitamin D intake in segments of the population. We review the pathophysiology of the calcium-alkali syndrome. PMID:24288027

  17. Synthesis and studies on microhardness of alkali zinc borate glasses

    SciTech Connect

    Subhashini, Bhattacharya, Soumalya Shashikala, H. D. Udayashankar, N. K.

    2014-04-24

    The mixed alkali effect on zinc borate glasses have been reported. The glass systems of nominal composition 10Zn+xLi{sub 2}O+yNa{sub 2}O+80B{sub 2}O{sub 3} (x = y = 0, 5, 10, 15 mol%) were prepared using standard melt quenching method. The structural, physical and mechanical properties of the samples have been studied using X-ray diffraction(XRD), density measurement and Vickers hardness measurement, respectively. A consistent increase in the density was observed, which explains the role of the modifiers (Li{sub 2}O and Na{sub 2}O) in the network modification of borate structure. The molar volume is decreasing linearly with the alkali concentration, which is attributed to the conversion of tetrahedral boron (BO{sub 4/2}){sup −} into (BO{sub 3/2}){sup −}. The microhardness studies reveals the anisotropy nature of the material. It further confirms that the samples belong to hard glass category.

  18. Alkali-Doped Lithium Orthosilicate Sorbents for Carbon Dioxide Capture.

    PubMed

    Yang, Xinwei; Liu, Wenqiang; Sun, Jian; Hu, Yingchao; Wang, Wenyu; Chen, Hongqiang; Zhang, Yang; Li, Xian; Xu, Minghou

    2016-09-01

    New alkali-doped (Na2 CO3 and K2 CO3 ) Li4 SiO4 sorbents with excellent performance at low CO2 concentrations were synthesized. We speculate that alkali doping breaks the orderly arrangement of the Li4 SiO4 crystals, hence increasing its specific surface area and the number of pores. It was shown that 10 wt % Na2 CO3 and 5 wt % K2 CO3 are the optimal additive ratios for doped sorbents to attain the highest conversions. Moreover, under 15 vol % CO2 , the doped sorbents present clearly faster absorption rates and exhibit stable cyclic durability with impressive conversions of about 90 %, at least 20 % higher than that of non-doped Li4 SiO4 . The attained conversions are also 10 % higher than the reported highest conversion of 80 % on doped Li4 SiO4 . The performance of Li4 SiO4 is believed to be enhanced by the eutectic melt, and it is the first time that the existence of eutectic Li/Na or Li/K carbonate on doped sorbents when absorbing CO2 at high temperature is confirmed; this was done using systematical analysis combining differential scanning calorimetry with in situ powder X-ray diffraction. PMID:27531239

  19. Radiolytic generation of radical cations in xenon matrices. Tetramethylcyclopropane radical cation and its transformations

    SciTech Connect

    Qin, X.Z.; Trifunac, A.D. )

    1990-04-05

    Radiolytic generation of radical cations in xenon matrices containing electron scavengers is illustrated by studying the 1,1,2,2-tetramethylcyclopropane radical cation. Dilute and concentrated solutions of tetramethylcyclopropane in xenon without electron scavengers and neat tetramethylcyclopropane yielded neutral radicals upon {gamma}-irradiation. Speculation on the mechanisms of radical formation is presented. The radical species observed in the {gamma}-irradiation of neat tetramethylcyclopropane appears to be identical with the paramagnetic species observed in CF{sub 2}ClCFCl{sub 2} above 120 K, suggesting that a neutral radical rather than the ring-opened distonic radical cation is observed in the CF{sub 2}ClCFCl{sub 2} matrix.

  20. Reduction in the concentration of cation vacancies by proper Si-doping in the well layers of high AlN mole fraction Al{sub x}Ga{sub 1–x}N multiple quantum wells grown by metalorganic vapor phase epitaxy

    SciTech Connect

    Chichibu, S. F. Ishikawa, Y.; Furusawa, K.; Miyake, H.; Hiramatsu, K.

    2015-09-21

    Appropriate-amount Si-doping in the well layers significantly improved the luminescence efficiency of Al{sub 0.68}Ga{sub 0.32}N/Al{sub 0.77}Ga{sub 0.23}N multiple quantum wells. To understand the mechanisms, spatio-time-resolved cathodoluminescence measurements and self-consistent Schrödinger-Poisson calculations were carried out. The increase in the luminescence lifetime at room temperature, which reflects the decrease in the concentration of nonradiative recombination centers (NRCs), was correlated with increased terrace width of Si-doped wells. The results suggest the importance of H{sub 3}SiNH{sub 2} doping-reactant formation that gives rise to enhanced decomposition of NH{sub 3} and provides wetting conditions by surface Si-N bonds, which reduce the total energy and concentration of NRCs composed of cation vacancies.

  1. Alkali metal recovery from carbonaceous material conversion process

    DOEpatents

    Sharp, David W.; Clavenna, LeRoy R.; Gorbaty, Martin L.; Tsou, Joe M.

    1980-01-01

    In a coal gasification operation or similar conversion process carried out in the presence of an alkali metal-containing catalyst wherein solid particles containing alkali metal residues are produced in the gasifier or similar reaction zone, alkali metal constitutents are recovered from the particles by withdrawing and passing the particles from the reaction zone to an alkali metal recovery zone in the substantial absence of molecular oxygen and treating the particles in the recovery zone with water or an aqueous solution in the substantial absence of molecular oxygen. The solution formed by treating the particles in the recovery zone will contain water-soluble alkali metal constituents and is recycled to the conversion process where the alkali metal constituents serve as at least a portion of the alkali metal constituents which comprise the alkali metal-containing catalyst. Preventing contact of the particles with oxygen as they are withdrawn from the reaction zone and during treatment in the recovery zone avoids the formation of undesirable alkali metal constituents in the aqueous solution produced in the recovery zone and insures maximum recovery of water-soluble alkali metal constituents from the alkali metal residues.

  2. Alkali element background reduction in laser ICP-MS

    NASA Astrophysics Data System (ADS)

    Magee, C. W., Jr.; Norris, C. A.

    2014-11-01

    Alkali backgrounds in laser ablation ICP-MS analyses can be enhanced by electron-induced ionization of alkali contamination on the skimmer cone, reducing effective detection limits for these elements. Traditionally, this problem is addressed by isolating analyses of high alkali materials onto a designated cone set, or by operating the ICP-MS in a "soft extraction" mode, which reduces the energy of electrons repelled into the potentially contaminated sampling cone by the extraction field. Here we present a novel approach, where we replace the traditional alkali glass tuning standards with synthetic low-alkali glass reference materials. Using this vitreous tuning solution, we find that this approach reduces the amount of alkali contamination produced, halving backgrounds for the heavy alkali elements without any change to analytical procedures. Using segregated cones is still the most effective method for reducing lithium backgrounds, but since the procedures are complimentary both can easily be applied to the routine operations of an analytical lab.

  3. Alkali element background reduction in laser ICP-MS

    NASA Astrophysics Data System (ADS)

    Magee, C. W., Jr.; Norris, C. A.

    2015-03-01

    Alkali backgrounds in laser ablation ICP-MS analyses can be enhanced by electron-induced ionisation of alkali contamination on the skimmer cone, reducing effective detection limits for these elements. Traditionally, this problem is addressed by isolating analyses of high-alkali materials onto a designated cone set, or by operating the ICP-MS in a "soft extraction" mode, which reduces the energy of electrons repelled into the potentially contaminated sampling cone by the extraction field. Here we present a novel approach, where we replace the traditional alkali glass tuning standards with synthetic low-alkali glass reference materials. Using this vitreous tuning solution, we find that this approach reduces the amount of alkali contamination produced, halving backgrounds for the heavy alkali elements without any change to analytical procedures. Using segregated cones is still the most effective method for reducing lithium backgrounds, but since the procedures are complimentary, both can easily be applied to the routine operations of an analytical lab.

  4. Novel penetrating cations for targeting mitochondria.

    PubMed

    Chernyak, Boris V; Antonenko, Yuri N; Domnina, Lidia V; Ivanova, Olga Yu; Lyamzaev, Konstantin G; Pustovidko, Antonina V; Rokitskaya, Tatiana I; Severina, Inna I; Simonyan, Ruben A; Trendeleva, Tatiana A; Zvyagilskaya, Renata A

    2013-01-01

    Novel penetrating cations were used for the design of mitochondria-targeted compounds and tested in model lipid membranes, in isolated mitochondria and in living human cells in culture. Rhodamine-19, berberine and palmatine were conjugated by aliphatic linkers with plastoquinone possessing antioxidant activity. These conjugates (SkQR1,SkQBerb, SkQPalm) and their analogs lacking plastoquinol moiety (C12R1,C10Berb and C10Palm) penetrated bilayer phospholipid membrane in their cationic forms and accumulated in isolated mitochondria or in mitochondria of living cells due to membrane potential negative inside. Reduced forms of SkQR1, SkQBerb and SkQPalm inhibited lipid peroxidation in isolated mitochondria at nanomolar concentrations. In human fibroblasts SkQR1, SkQBerb and SkQPalm prevented fragmentation of mitochondria and apoptosis induced by hydrogen peroxide. SkQR1 was effective at subnanomolar concentrations while SkQberb, SkQPalm and SkQ1 (prototypic conjugate of plastoquinone with dodecyltriphenylphosphonium) were effective at 10-times higher concentrations. The aliphatic conjugates of berberine and palmatine (as well as the conjugates of triphenylphosphonium) induced proton transport mediated by free fatty acids (FA) both in the model and mitochondrial membrane. In mitochondria this process was facilitated by the adenine nucleotide carrier. In contrast to the other cationic conjugates, SkQR1 and C12R1 induced FA-independent proton conductivity due to protonation/deprotonation of the rhodamine residue. This property in combination with the antioxidant activity probably makes rhodamine conjugates highly effective in protection against oxidative stress. The novel cationic conjugates described here are promising candidates for drugs against various pathologies and aging as mitochondria-targeted antioxidants and selective mild uncouplers. PMID:23092317

  5. Heterovalent substitutions in garnet and their implications for diffusion of Y+REEs and alkalis (Invited)

    NASA Astrophysics Data System (ADS)

    Carlson, W. D.; Gale, J. D.; Wright, K.

    2013-12-01

    Lattice-dynamics calculations in the static limit suggest that large trivalent ions (Y+REEs) are incorporated into garnet primarily by means of substitutions that introduce menzerite and alkali components. The diffusion mechanisms implied by this finding explain otherwise puzzling aspects of recent determinations of diffusion rates for Y+REEs and Li in natural systems, bolstering confidence in the validity of those rates. Several substitution schemes have been proposed to provide the charge-balance required for incorporation of trivalent Y+REEs substituting for divalent cations in dodecahedral sites in aluminosilicate garnet: (1) YAG components, with tetrahedral Al; (2) vacancy components, with one unoccupied dodecahedral site for each two trivalent ions; (3) alkali components, with dodecahedral Na or Li; (4) menzerite components, with octahedral Mg or Fe; and (5) Y2Li components, with octahedral Li compensating for a pair of Y+REE ions. The relative energetic costs of these substitutions were evaluated in pyrope, almandine, spessartine and grossular by means of lattice-dynamics calculations at T = 0 K and P = 0 GPa, using well-established force-field potentials, and referencing exchange energies to the lattice energies of binary oxides as sources/sinks for the exchanged ions. Energies calculated for the incorporation of menzerite and alkali components are appreciably lower than those for the YAG component, and very substantially lower than those for the other components. Provided that the relative energetic costs are similar at elevated T and P to those in the static limit (testing of this assumption is currently underway), the menzerite and alkali substitutions should predominate in natural aluminosilicate garnets, the YAG substitution should play only a subordinate role, and the other substitutions should be near-negligible. As a result, diffusion mechanisms for Y+REEs in garnet require that motion of these elements must be coupled to transport of either

  6. Study on cationic photopolymerization reaction of epoxy polysiloxane

    NASA Astrophysics Data System (ADS)

    Sun, F.; Jiang, S. L.; Liu, J.

    2007-11-01

    The effects of epoxy monomers, concentration of photoinitiator and radical photoinitiators on the photosensitive properties of cationic phopolymerization system with a novel epoxy polysiloxane oligomer (CEPS) were investigated via a gel yield method. The results showed that among the tested epoxy monomers, the reactivity of ERL-4221 with cycloaliphatic epoxy groups was the highest. The optimum concentration of diaryldiodonium salt (SR-1012) was determined as 4-5 wt.%. Increasing the amounts of ERL-4221 in the CEPS cationic photopolymerization system, UV-curing rate increased. Radical photoinitiators with ArC dbnd O structure possessed sensitization capacity to the cationic photoinitiator SR-1012. The photosensitivity of the CEPS system could be up to 165 mJ/cm 2. Adding a small amount of IPA and BP could greatly improve the photosensitivity of CEPS cationic photosensitive system. The optimal quantity of isopropanol added to the system was not more than 2 wt.%.

  7. Affinity Capillary Electrophoresis Applied to Investigation of Valinomycin Complexes with Ammonium and Alkali Metal Ions.

    PubMed

    Štěpánová, Sille; Kašička, Václav

    2016-01-01

    This chapter deals with the application of affinity capillary electrophoresis (ACE) to investigation of noncovalent interactions (complexes) of valinomycin, a macrocyclic dodecadepsipeptide antibiotic ionophore, with ammonium and alkali metal ions (lithium, sodium, potassium, rubidium, and cesium). The strength of these interactions was characterized by the apparent binding (stability, association) constants (K b) of the above valinomycin complexes using the mobility shift assay mode of ACE. The study involved measurements of effective electrophoretic mobility of valinomycin at variable concentrations of ammonium or alkali metal ions in the background electrolyte (BGE). The effective electrophoretic mobilities of valinomycin measured at ambient temperature and variable ionic strength were first corrected to the reference temperature 25 °C and constant ionic strength (10 or 25 mM). Then, from the dependence of the corrected valinomycin effective mobility on the ammonium or alkali metal ion concentration in the BGE, the apparent binding constants of the valinomycin-ammonium or valinomycin-alkali metal ion complexes were determined using a nonlinear regression analysis. Logarithmic form of the binding constants (log K b) were found to be in the range of 1.50-4.63, decreasing in the order Rb(+) > K(+) > Cs(+) > > Na(+) > NH4 (+) ~ Li(+). PMID:27473493

  8. Alkali halide-assisted penetration of neostigmine across excised human skin: a combination of structured water disruption and a Donnan-like effect.

    PubMed

    Michael-Baruch, E; Shiri, Y; Cohen, S

    1994-08-01

    The penetration of neostigmine across excised human skin mounted in flow-through diffusion cells, delivered from a 0.28 M aqueous solution, was below detection limits. The presence of either NaCl or LiCl in the donor solution caused significant fluxes of neostigmine, with permeability coefficients (Kp's) in the range of 10(-6) cm min-1. Paradoxically, low concentrations of NaCl or LiCl (0.25 and 0.5 M) were more effective in this respect than the 1 M solution, which was the least effective concentration in the range of 0.25-3 M. Thus, the dependence of the experimental Kp values on inorganic ion concentration followed a biphasic course, suggesting the participation of two distinctive mechanisms in the penetration-enhancement process. The early phase corresponding to 0.25 and 0.5 M NaCl or LiCl is being partly ascribed to a decrease in the viscosity of lamellar water caused by the influx of the respective hydrated ions, hydration of LiCl or NaCl being more extensive at low alkali halide concentration that at higher ones (reference cited). The late phase corresponding to 2 and 3 M LiCl and NaCl is partly ascribed to a Donnan-like effect whereby the presence of a large excess of poorly diffusible common ion (Na+ or Li+) enhances the partitioning into the skin of the more diffusible ion, in this case neostigmine cation. The presence of inorganic ions at different concentrations had no effect on the partial molal volume of neostigmine bromide (Vi infinity = 223.5 cm3 mol-1), which was practically the same for all concentrations of either LiCl and NaCl.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:7983588

  9. Developments in alkali-metal atomic magnetometry

    NASA Astrophysics Data System (ADS)

    Seltzer, Scott Jeffrey

    Alkali-metal magnetometers use the coherent precession of polarized atomic spins to detect and measure magnetic fields. Recent advances have enabled magnetometers to become competitive with SQUIDs as the most sensitive magnetic field detectors, and they now find use in a variety of areas ranging from medicine and NMR to explosives detection and fundamental physics research. In this thesis we discuss several developments in alkali-metal atomic magnetometry for both practical and fundamental applications. We present a new method of polarizing the alkali atoms by modulating the optical pumping rate at both the linear and quadratic Zeeman resonance frequencies. We demonstrate experimentally that this method enhances the sensitivity of a potassium magnetometer operating in the Earth's field by a factor of 4, and we calculate that it can reduce the orientation-dependent heading error to less than 0.1 nT. We discuss a radio-frequency magnetometer for detection of oscillating magnetic fields with sensitivity better than 0.2 fT/ Hz , which we apply to the observation of nuclear magnetic resonance (NMR) signals from polarized water, as well as nuclear quadrupole resonance (NQR) signals from ammonium nitrate. We demonstrate that a spin-exchange relaxation-free (SERF) magnetometer can measure all three vector components of the magnetic field in an unshielded environment with comparable sensitivity to other devices. We find that octadecyltrichlorosilane (OTS) acts as an anti-relaxation coating for alkali atoms at temperatures below 170°C, allowing them to collide with a glass surface up to 2,000 times before depolarizing, and we present the first demonstration of high-temperature magnetometry with a coated cell. We also describe a reusable alkali vapor cell intended for the study of interactions between alkali atoms and surface coatings. Finally, we explore the use of a cesium-xenon SERF comagnetometer for a proposed measurement of the permanent electric dipole moments (EDMs

  10. Effect of cofiring coal and biofuel with sewage sludge on alkali problems in a circulating fluidized bed boiler

    SciTech Connect

    K.O. Davidsson; L.-E. Aamand; A.-L. Elled; B. Leckner

    2007-12-15

    Cofiring experiments were performed in a 12 MW circulating fluidized bed boiler. The fuel combinations were biofuel (wood+straw), coal+biofuel, coal+sewage sludge+biofuel, and sewage sludge+biofuel. Limestone or chlorine (PVC) was added in separate experiments. Effects of feed composition on bed ash and fly ash were examined. The composition of flue gas was measured, including on-line measurement of alkali chlorides. Deposits were collected on a probe simulating a superheater tube. It was found that the fuel combination, as well as addition of limestone, has little effect on the alkali fraction in bed ash, while chlorine decreases the alkali fraction in bed ash. Sewage sludge practically eliminates alkali chlorides in flue gas and deposits. Addition of enough limestone to coal and sludge for elimination of the SO{sub 2} emission does not change the effect of chlorine. Chlorine addition increases the alkali chloride in flue gas, but no chlorine was found in the deposits with sewage sludge as a cofuel. Cofiring of coal and biofuel lowers the alkali chloride concentration in the flue gas to about a third compared with that of pure biofuel. This is not affected by addition of lime or chlorine. It is concluded that aluminum compounds in coal and sludge are more important than sulfur to reduce the level of KCl in flue gas and deposits. 24 refs., 8 figs., 7 tabs.

  11. Gel nanostructure in alkali-activated binders based on slag and fly ash, and effects of accelerated carbonation

    SciTech Connect

    Bernal, Susan A.; Provis, John L.; Walkley, Brant; San Nicolas, Rackel; Gehman, John D.; Brice, David G.; Kilcullen, Adam R.; Duxson, Peter; Deventer, Jannie S.J. van

    2013-11-15

    Binders formed through alkali-activation of slags and fly ashes, including ‘fly ash geopolymers’, provide appealing properties as binders for low-emissions concrete production. However, the changes in pH and pore solution chemistry induced during accelerated carbonation testing provide unrealistically low predictions of in-service carbonation resistance. The aluminosilicate gel remaining in an alkali-activated slag system after accelerated carbonation is highly polymerised, consistent with a decalcification mechanism, while fly ash-based binders mainly carbonate through precipitation of alkali salts (bicarbonates at elevated CO{sub 2} concentrations, or carbonates under natural exposure) from the pore solution, with little change in the binder gel identifiable by nuclear magnetic resonance spectroscopy. In activated fly ash/slag blends, two distinct gels (C–A–S–H and N–A–S–H) are formed; under accelerated carbonation, the N–A–S–H gel behaves comparably to fly ash-based systems, while the C–A–S–H gel is decalcified similarly to alkali-activated slag. This provides new scope for durability optimisation, and for developing appropriate testing methodologies. -- Highlights: •C-A-S-H gel in alkali-activated slag decalcifies during accelerated carbonation. •Alkali-activated fly ash gel changes much less under CO{sub 2} exposure. •Blended slag-fly ash binder contains two coexisting gel types. •These two gels respond differently to carbonation. •Understanding of carbonation mechanisms is essential in developing test methods.

  12. Silica-based cationic bilayers as immunoadjuvants

    PubMed Central

    Lincopan, Nilton; Santana, Mariana RA; Faquim-Mauro, Eliana; da Costa, Maria Helena B; Carmona-Ribeiro, Ana M

    2009-01-01

    Background Silica particles cationized by dioctadecyldimethylammonium bromide (DODAB) bilayer were previously described. This work shows the efficiency of these particulates for antigen adsorption and presentation to the immune system and proves the concept that silica-based cationic bilayers exhibit better performance than alum regarding colloid stability and cellular immune responses for vaccine design. Results Firstly, the silica/DODAB assembly was characterized at 1 mM NaCl, pH 6.3 or 5 mM Tris.HCl, pH 7.4 and 0.1 mg/ml silica over a range of DODAB concentrations (0.001–1 mM) by means of dynamic light scattering for particle sizing and zeta-potential analysis. 0.05 mM DODAB is enough to produce cationic bilayer-covered particles with good colloid stability. Secondly, conditions for maximal adsorption of bovine serum albumin (BSA) or a recombinant, heat-shock protein from Mycobacterium leprae (18 kDa-hsp) onto DODAB-covered or onto bare silica were determined. At maximal antigen adsorption, cellular immune responses in vivo from delayed-type hypersensitivity reactions determined by foot-pad swelling tests (DTH) and cytokines analysis evidenced the superior performance of the silica/DODAB adjuvant as compared to alum or antigens alone whereas humoral response from IgG in serum was equal to the one elicited by alum as adjuvant. Conclusion Cationized silica is a biocompatible, inexpensive, easily prepared and possibly general immunoadjuvant for antigen presentation which displays higher colloid stability than alum, better performance regarding cellular immune responses and employs very low, micromolar doses of cationic and toxic synthetic lipid. PMID:19152701

  13. Effect of alkali lignins with different molecular weights from alkali pretreated rice straw hydrolyzate on enzymatic hydrolysis.

    PubMed

    Li, Yun; Qi, Benkun; Luo, Jianquan; Wan, Yinhua

    2016-01-01

    This study investigated the effect of alkali lignins with different molecular weights on enzymatic hydrolysis of lignocellulose. Different alkali lignins fractions, which were obtained from cascade ultrafiltration, were added into the dilute acid pretreated (DAP) and alkali pretreated (AP) rice straws respectively during enzymatic hydrolysis. The results showed that the addition of alkali lignins enhanced the hydrolysis and the enhancement for hydrolysis increased with increasing molecular weights of alkali lignins, with maximum enhancement being 28.69% for DAP and 20.05% for AP, respectively. The enhancement was partly attributed to the improved cellulase activity, and filter paper activity increased by 18.03% when adding lignin with highest molecular weight. It was found that the enhancement of enzymatic hydrolysis was correlated with the adsorption affinity of cellulase on alkali lignins, and the difference in surface charge and hydrophobicity of alkali lignins were responsible for the difference in affinity between cellulase and lignins. PMID:26496216

  14. Removal of Retired Alkali Metal Test Systems

    SciTech Connect

    BREHM, W.F.

    2003-01-01

    This paper describes the successful effort to remove alkali metals, alkali metal residues, and piping and structures from retired non-radioactive test systems on the Hanford Site. These test systems were used between 1965 and 1982 to support the Fast Flux Test Facility and the Liquid Metal Fast Breeder Reactor Program. A considerable volume of sodium and sodium-potassium alloy (NaK) was successfully recycled to the commercial sector; structural material and electrical material such as wiring was also recycled. Innovative techniques were used to safely remove NaK and its residues from a test system that could not be gravity-drained. The work was done safely, with no environmental issues or significant schedule delays.

  15. Removal of Retired Alkali Metal Test Systems

    SciTech Connect

    Brehm, W. F.; Church, W. R.; Biglin, J. W.

    2003-02-26

    This paper describes the successful effort to remove alkali metals, alkali metal residues, and piping and structures from retired non-radioactive test systems on the Hanford Site. These test systems were used between 1965 and 1982 to support the Fast Flux Test Facility and the Liquid Metal Fast Breeder Reactor Program. A considerable volume of sodium and sodium-potassium alloy (NaK) was successfully recycled to the commercial sector; structural material and electrical material such as wiring was also recycled. Innovative techniques were used to safely remove NaK and its residues from a test system that could not be gravity-drained. The work was done safely, with no environmental issues or significant schedule delays.

  16. Geopolymers and Related Alkali-Activated Materials

    NASA Astrophysics Data System (ADS)

    Provis, John L.; Bernal, Susan A.

    2014-07-01

    The development of new, sustainable, low-CO2 construction materials is essential if the global construction industry is to reduce the environmental footprint of its activities, which is incurred particularly through the production of Portland cement. One type of non-Portland cement that is attracting particular attention is based on alkali-aluminosilicate chemistry, including the class of binders that have become known as geopolymers. These materials offer technical properties comparable to those of Portland cement, but with a much lower CO2 footprint and with the potential for performance advantages over traditional cements in certain niche applications. This review discusses the synthesis of alkali-activated binders from blast furnace slag, calcined clay (metakaolin), and fly ash, including analysis of the chemical reaction mechanisms and binder phase assemblages that control the early-age and hardened properties of these materials, in particular initial setting and long-term durability. Perspectives for future research developments are also explored.

  17. Quantum magnetism of alkali Rydberg atoms

    NASA Astrophysics Data System (ADS)

    Malinovskaya, Svetlana; Liu, Gengyuan

    2016-05-01

    We discuss a method to control dynamics in many-body spin states of 87Rb Rydberg atoms. The method permits excitation of cold gases and form ordered structures of alkali atoms. It makes use of a two-photon excitation scheme with circularly polarized and linearly chirped pulses. The method aims for controlled quantum state preparation in large ensembles. It is actual for experiments studding the spin hopping dynamics and realization of quantum random walks.

  18. Alkali Metal Heat Pipe Life Issues

    NASA Technical Reports Server (NTRS)

    Reid, Robert S.

    2004-01-01

    One approach to space fission power system design is predicated on the use of alkali metal heat pipes, either as radiator elements, thermal management components, or as part of the core primary heat-transfer system. This synopsis characterizes long-life core heat pipes. References are included where more detailed information can be found. Specifics shown here are for demonstrational purposes and do not necessarily reflect current Project Prometheus point designs.

  19. Alkali metal protective garment and composite material

    SciTech Connect

    Ballif, J.L.; Yuan, W.W.

    1980-09-16

    A protective garment and composite material providing satisfactory heat resistance and physical protection for articles and personnel exposed to hot molten alkali metals, such as sodium are described. Physical protection is provided by a continuous layer of nickel foil. Heat resistance is provided by an underlying backing layer of thermal insulation. Overlying outer layers of fireproof woven ceramic fibers are used to protect the foil during storage and handling.

  20. Alkali metal protective garment and composite material

    SciTech Connect

    Ballif, III, John L.; Yuan, Wei W.

    1980-01-01

    A protective garment and composite material providing satisfactory heat resistance and physical protection for articles and personnel exposed to hot molten alkali metals, such as sodium. Physical protection is provided by a continuous layer of nickel foil. Heat resistance is provided by an underlying backing layer of thermal insulation. Overlying outer layers of fireproof woven ceramic fibers are used to protect the foil during storage and handling.

  1. Transport properties of alkali metal doped fullerides

    SciTech Connect

    Yadav, Daluram Yadav, Nishchhal

    2015-07-31

    We have studied the intercage interactions between the adjacent C{sub 60} cages and expansion of lattice due to the intercalation of alkali atoms based on the spring model to estimate phonon frequencies from the dynamical matrix for the intermolecular alkali-C{sub 60} phonons. We considered a two-peak model for the phonon density of states to investigate the nature of electron pairing mechanism for superconducting state in fullerides. Coulomb repulsive parameter and the electron phonon coupling strength are obtained within the random phase approximation. Transition temperature, T{sub c}, is obtained in a situation when the free electrons in lowest molecular orbital are coupled with alkali-C{sub 60} phonons as 5 K, which is much lower as compared to reported T{sub c} (20 K). The superconducting pairing is mainly driven by the high frequency intramolecular phonons and their effects enhance it to 22 K. The importance of the present study, the pressure effect and normal state transport properties are calculated within the same model leading superconductivity.

  2. Transport properties of alkali metal doped fullerides

    NASA Astrophysics Data System (ADS)

    Yadav, Daluram; Yadav, Nishchhal

    2015-07-01

    We have studied the intercage interactions between the adjacent C60 cages and expansion of lattice due to the intercalation of alkali atoms based on the spring model to estimate phonon frequencies from the dynamical matrix for the intermolecular alkali-C60 phonons. We considered a two-peak model for the phonon density of states to investigate the nature of electron pairing mechanism for superconducting state in fullerides. Coulomb repulsive parameter and the electron phonon coupling strength are obtained within the random phase approximation. Transition temperature, Tc, is obtained in a situation when the free electrons in lowest molecular orbital are coupled with alkali-C60 phonons as 5 K, which is much lower as compared to reported Tc (20 K). The superconducting pairing is mainly driven by the high frequency intramolecular phonons and their effects enhance it to 22 K. The importance of the present study, the pressure effect and normal state transport properties are calculated within the same model leading superconductivity.

  3. Characterization of Adsorbed Alkali Metal Ions in 2:1 Type Clay Minerals from First-Principles Metadynamics.

    PubMed

    Ikeda, Takashi; Suzuki, Shinichi; Yaita, Tsuyoshi

    2015-07-30

    Adsorption states of alkali metal ions in three kinds of 2:1 type clay minerals are systematically investigated via first-principles-based metadynamics. Our reconstructed free energy surfaces in a two-dimensional space of coordination numbers specifically employed as collective variables for describing the interlayer cations show that an inner-sphere (IS) complex is preferentially formed for Cs(+) in the 2:1 type trioctahedral clay minerals with saponite-like compositions, where lighter alkali metal ions show a tendency to form an outer-sphere one instead. The strong preference for an IS complex observed for Cs(+) is found to result partially from the capability of recognizing selectively Cs(+) ions at the basal O atoms with the Lewis basicity significantly enhanced by the isomorphic substitution in tetrahedral sheets. PMID:26151150

  4. Selective flotation of PVC using gelatin and lignin alkali.

    PubMed

    Yenial, Unzile; Kangal, Olgaç; Güney, Ali

    2013-06-01

    Recycling has become one of the most important issues as a result of increasing waste mass in present day. This is especially important for polymer wastes as they are hard to degenerate in nature. Today, most of the practical methods used for the recycling of waste mass, such as hand sorting, gravity separation, etc., cannot be performed successfully owing to close densities of polymers. Froth flotation can be used successfully and economically for this purpose. The main objective of this study was to investigate the effect of plasticizer reagents and the success of froth flotation at plastic recycling. In this study, lignin alkali and gelatin were used as plasticizer reagents. The effect of these reagents was searched with the parameters of pH, concentration, conditioning and flotation time. In the case of post-consumed polyethylene terephthalate and polyvinyl chloride (PVC), 98.9% purity of PVC was obtained at optimum conditions. PMID:23439876

  5. Penetrating cations enhance uncoupling activity of anionic protonophores in mitochondria.

    PubMed

    Antonenko, Yuri N; Khailova, Ljudmila S; Knorre, Dmitry A; Markova, Olga V; Rokitskaya, Tatyana I; Ilyasova, Tatyana M; Severina, Inna I; Kotova, Elena A; Karavaeva, Yulia E; Prikhodko, Anastasia S; Severin, Fedor F; Skulachev, Vladimir P

    2013-01-01

    Protonophorous uncouplers causing a partial decrease in mitochondrial membrane potential are promising candidates for therapeutic applications. Here we showed that hydrophobic penetrating cations specifically targeted to mitochondria in a membrane potential-driven fashion increased proton-translocating activity of the anionic uncouplers 2,4-dinitrophenol (DNP) and carbonylcyanide-p-trifluorophenylhydrazone (FCCP). In planar bilayer lipid membranes (BLM) separating two compartments with different pH values, DNP-mediated diffusion potential of H(+) ions was enhanced in the presence of dodecyltriphenylphosphonium cation (C12TPP). The mitochondria-targeted penetrating cations strongly increased DNP- and carbonylcyanide m-chlorophenylhydrazone (CCCP)-mediated steady-state current through BLM when a transmembrane electrical potential difference was applied. Carboxyfluorescein efflux from liposomes initiated by the plastoquinone-containing penetrating cation SkQ1 was inhibited by both DNP and FCCP. Formation of complexes between the cation and CCCP was observed spectophotometrically. In contrast to the less hydrophobic tetraphenylphosphonium cation (TPP), SkQ1 and C12TPP promoted the uncoupling action of DNP and FCCP on isolated mitochondria. C12TPP and FCCP exhibited a synergistic effect decreasing the membrane potential of mitochondria in yeast cells. The stimulating action of penetrating cations on the protonophore-mediated uncoupling is assumed to be useful for medical applications of low (non-toxic) concentrations of protonophores. PMID:23626747

  6. Penetrating Cations Enhance Uncoupling Activity of Anionic Protonophores in Mitochondria

    PubMed Central

    Antonenko, Yuri N.; Khailova, Ljudmila S.; Knorre, Dmitry A.; Markova, Olga V.; Rokitskaya, Tatyana I.; Ilyasova, Tatyana M.; Severina, Inna I.; Kotova, Elena A.; Karavaeva, Yulia E.; Prikhodko, Anastasia S.; Severin, Fedor F.; Skulachev, Vladimir P.

    2013-01-01

    Protonophorous uncouplers causing a partial decrease in mitochondrial membrane potential are promising candidates for therapeutic applications. Here we showed that hydrophobic penetrating cations specifically targeted to mitochondria in a membrane potential-driven fashion increased proton-translocating activity of the anionic uncouplers 2,4-dinitrophenol (DNP) and carbonylcyanide-p-trifluorophenylhydrazone (FCCP). In planar bilayer lipid membranes (BLM) separating two compartments with different pH values, DNP-mediated diffusion potential of H+ ions was enhanced in the presence of dodecyltriphenylphosphonium cation (C12TPP). The mitochondria-targeted penetrating cations strongly increased DNP- and carbonylcyanide m-chlorophenylhydrazone (CCCP)-mediated steady-state current through BLM when a transmembrane electrical potential difference was applied. Carboxyfluorescein efflux from liposomes initiated by the plastoquinone-containing penetrating cation SkQ1 was inhibited by both DNP and FCCP. Formation of complexes between the cation and CCCP was observed spectophotometrically. In contrast to the less hydrophobic tetraphenylphosphonium cation (TPP), SkQ1 and C12TPP promoted the uncoupling action of DNP and FCCP on isolated mitochondria. C12TPP and FCCP exhibited a synergistic effect decreasing the membrane potential of mitochondria in yeast cells. The stimulating action of penetrating cations on the protonophore-mediated uncoupling is assumed to be useful for medical applications of low (non-toxic) concentrations of protonophores. PMID:23626747

  7. Cation exchange properties of zeolites in hyper alkaline aqueous media.

    PubMed

    Van Tendeloo, Leen; de Blochouse, Benny; Dom, Dirk; Vancluysen, Jacqueline; Snellings, Ruben; Martens, Johan A; Kirschhock, Christine E A; Maes, André; Breynaert, Eric

    2015-02-01

    Construction of multibarrier concrete based waste disposal sites and management of alkaline mine drainage water requires cation exchangers combining excellent sorption properties with a high stability and predictable performance in hyper alkaline media. Though highly selective organic cation exchange resins have been developed for most pollutants, they can serve as a growth medium for bacterial proliferation, impairing their long-term stability and introducing unpredictable parameters into the evolution of the system. Zeolites represent a family of inorganic cation exchangers, which naturally occur in hyper alkaline conditions and cannot serve as an electron donor or carbon source for microbial proliferation. Despite their successful application as industrial cation exchangers under near neutral conditions, their performance in hyper alkaline, saline water remains highly undocumented. Using Cs(+) as a benchmark element, this study aims to assess the long-term cation exchange performance of zeolites in concrete derived aqueous solutions. Comparison of their exchange properties in alkaline media with data obtained in near neutral solutions demonstrated that the cation exchange selectivity remains unaffected by the increased hydroxyl concentration; the cation exchange capacity did however show an unexpected increase in hyper alkaline media. PMID:25569300

  8. Dissecting the cation-cation interaction between two uranyl units.

    PubMed

    Tecmer, Paweł; Hong, Sung W; Boguslawski, Katharina

    2016-07-21

    We present a state-of-the-art computational study of the uranyl(vi) and uranyl(v) cation-cation interactions (dications) in aqueous solution. Reliable electronic structures of two interacting uranyl(vi) and uranyl(v) subunits as well as those of the uranyl(vi) and uranyl(v) clusters are presented for the first time. Our theoretical study elucidates the impact of cation-cation interactions on changes in the molecular structure as well as changes in vibrational and UV-Vis spectra of the bare uranyl(vi) and uranyl(v) moieties for different total spin-states and total charges of the dications. PMID:27335229

  9. Interfacial alkali diffusion control in chalcopyrite thin-film solar cells.

    PubMed

    Ishizuka, Shogo; Yamada, Akimasa; Fons, Paul J; Shibata, Hajime; Niki, Shigeru

    2014-08-27

    Alkali elements, specifically sodium (Na), are key materials to enhance the energy conversion efficiencies of chalcopyrite and related thin-film photovoltaic solar cells. Recently, the effect of potassium (K) has also attracted attention because elemental K has unique effects different from Na as well as a similar beneficial effect in improving device performance. In this study, the control of selective alkali K and Na diffusion into chalcopyrite thin-films from soda-lime glass substrates, which serve as the monolithic alkali source material and contain both K and Na, is demonstrated using ternary CuGaSe2. Elemental K is found to be incorporated in the several ten nanometer thick Cu-deficient region, which is formed on the CuGaSe2 film surface, while Na is ejected, although both K and Na diffuse from the substrate to the CuGaSe2 film surface during growth. The alkali [K]/[Na] concentration ratio in the surface region of CuGaSe2 films strongly depends on the film structure and can be controlled by growth parameters under the same substrate temperature conditions. The results we present here offer new concepts necessary to explore and develop emerging new chalcopyrite and related materials and optimize their applications. PMID:25004458

  10. Structural and electronic properties of alkali-doped single-walled carbon nanotubes

    NASA Astrophysics Data System (ADS)

    Nemes, Norbert Marcel

    In this thesis, we study the properties of alkali doped single walled carbon nanotubes (SWNT). SWNT are crystallized into ropes, which display the one-dimensional electronic properties of the constituent nanotubes. Using x-ray diffraction, we show that the alkali atoms invade the channels in the triangular rope lattice and determine the structure of the doped ropes. We show that the diffraction profile of the doped SWNT is best described by a model where the alkali ions surround each tube in an ordered fashion by dilating the channels. Alkali doped SWNT exhibit colors similar to alkali doped graphite (GIC). We study their electronic structure with IR reflectivity; the alkali dopants donate their valence electron to the SWNT host, so the free carrier concentration increases, shifting the Drude-edge into the visible spectral range. This is accompanied by a large shift of the Fermi-level, so the characteristic transitions between the 1D van Hove singularities of the undoped SWNT diminish. The presence of the alkali ions around the SWNT breaks the translational symmetry and increases coupling between parallel tubes within ropes. We find that the momentum relaxation time shortens as the ropes become more three dimensional. We also find that alkali disorder contributes to the scattering. In p-type, HNO3 doped SWNT, the charge transfer is smaller; only the first subband of the semiconducting tubes gets depleted, shown by the disappearance of the first van Hove transition. This indicates a Fermi-level shift of ˜0.3 eV. The reflectivity has structure at low energy, which moves the Drude-peak to a sharp, intense peak at 0.1 eV in the optical conductivity, reminiscent of quasi-1D TTF-TCNQ. The DC conductivity also increases ˜80-fold during doping. The low temperature divergence of undoped SWNT disappears in alkali doped SWNT. However, we find that oxygen can modulate the low-T divergence. After outgassing, the divergence becomes ˜10 times stronger. We interpret the low

  11. Method for the safe disposal of alkali metal

    DOEpatents

    Johnson, Terry R.

    1977-01-01

    Alkali metals such as those employed in liquid metal coolant systems can be safely reacted to form hydroxides by first dissolving the alkali metal in relatively inert metals such as lead or bismuth. The alloy thus formed is contacted with a molten salt including the alkali metal hydroxide and possibly the alkali metal carbonate in the presence of oxygen. This oxidizes the alkali metal to an oxide which is soluble within the molten salt. The salt is separated and contacted with steam or steam-CO.sub.2 mixture to convert the alkali metal oxide to the hydroxide. These reactions can be conducted with minimal hydrogen evolution and with the heat of reaction distributed between the several reaction steps.

  12. The cation-π interaction.

    PubMed

    Dougherty, Dennis A

    2013-04-16

    The chemistry community now recognizes the cation-π interaction as a major force for molecular recognition, joining the hydrophobic effect, the hydrogen bond, and the ion pair in determining macromolecular structure and drug-receptor interactions. This Account provides the author's perspective on the intellectual origins and fundamental nature of the cation-π interaction. Early studies on cyclophanes established that water-soluble, cationic molecules would forego aqueous solvation to enter a hydrophobic cavity if that cavity was lined with π systems. Important gas phase studies established the fundamental nature of the cation-π interaction. The strength of the cation-π interaction (Li(+) binds to benzene with 38 kcal/mol of binding energy; NH4(+) with 19 kcal/mol) distinguishes it from the weaker polar-π interactions observed in the benzene dimer or water-benzene complexes. In addition to the substantial intrinsic strength of the cation-π interaction in gas phase studies, the cation-π interaction remains energetically significant in aqueous media and under biological conditions. Many studies have shown that cation-π interactions can enhance binding energies by 2-5 kcal/mol, making them competitive with hydrogen bonds and ion pairs in drug-receptor and protein-protein interactions. As with other noncovalent interactions involving aromatic systems, the cation-π interaction includes a substantial electrostatic component. The six (four) C(δ-)-H(δ+) bond dipoles of a molecule like benzene (ethylene) combine to produce a region of negative electrostatic potential on the face of the π system. Simple electrostatics facilitate a natural attraction of cations to the surface. The trend for (gas phase) binding energies is Li(+) > Na(+) > K(+) > Rb(+): as the ion gets larger the charge is dispersed over a larger sphere and binding interactions weaken, a classical electrostatic effect. On other hand, polarizability does not define these interactions. Cyclohexane is

  13. The Cation-π Interaction

    PubMed Central

    DOUGHERTY, DENNIS A.

    2014-01-01

    CONSPECTUS The chemistry community now recognizes the cation-π interaction as a major force for molecular recognition, joining the hydrophobic effect, the hydrogen bond, and the ion pair in determining macromolecular structure and drug-receptor interactions. This Account provides the author’s perspective on the intellectual origins and fundamental nature of the cation-π interaction. Early studies on cyclophanes established that water-soluble, cationic molecules would forgo aqueous solvation to enter a hydrophobic cavity if that cavity was lined with π systems. Important gas phase studies established the fundamental nature of the cation-π interaction. The strength of the cation-π interaction – Li+ binds to benzene with 38 kcal/mol of binding energy; NH4+ with 19 kcal/mol– distinguishes it from the weaker polar-π interactions observed in the benzene dimer or water-benzene complexes. In addition to the substantial intrinsic strength of the cation-π interaction in gas phase studies, the cation-π interaction remains energetically significant in aqueous media and under biological conditions. Many studies have shown that cation-π interactions can enhance binding energies by 2 – 5 kcal/mol, making them competitive with hydrogen bonds and ion pairs in drug-receptor and protein-protein interactions. As with other noncovalent interactions involving aromatic systems, the cation-π interaction includes a substantial electrostatic component. The six (four) Cδ−–Hδ+ bond dipoles of a molecule like benzene (ethylene) combine to produce a region of negative electrostatic potential on the face of the π system. Simple electrostatics facilitate a natural attraction of cations to the surface. The trend for (gas phase) binding energies is Li+>Na+>K+>Rb+: as the ion gets larger the charge is dispersed over a larger sphere and binding interactions weaken, a classical electrostatic effect. On other hand, polarizability does not define these interactions. Cyclohexane

  14. Cationic lipid-mediated nucleic acid delivery: beyond being cationic.

    PubMed

    Rao, N Madhusudhana

    2010-03-01

    Realization of the potential of nucleic acids as drugs is intricately linked to their in vivo delivery. Cationic lipids demonstrated tremendous potential as safe, efficient and scalable in vitro carriers of nucleic acids. For in vivo delivery of nucleic acids, the extant two component liposomal preparations consisting of cationic lipids and nucleic acids have been largely found to be insufficient. Being a soft matter, liposomes readily respond to many physiological variables leading to complex component and morphological changes, thus confounding the efforts in a priori identification of a "competent" formulation. In the recent past many chemical moieties that provide advantage in facing the challenges of barriers in vivo, were incorporated into cationic lipids to improve the transfection efficiency. The cationic lipids, essential for DNA condensation and protection, definitely require additional components to be efficient in vivo. In addition, formulations of cationic lipid carriers with non-lipidic components, mainly peptides, have demonstrated success in in vivo transfection. The present review describes some recent successes of in vivo nucleic acid delivery by cationic lipids. PMID:20060819

  15. Microgel-like aggregates of isotactic and atactic poly(methacrylic acid) chains in aqueous alkali chloride solutions as evidenced by light scattering.

    PubMed

    Sitar, Simona; Aseyev, Vladimir; Kogej, Ksenija

    2014-10-21

    A comparative light-scattering study of isotactic and atactic poly(methacrylic acid), iPMA and aPMA, respectively, in aqueous solutions with added alkali chlorides, XCl (X = Li, Na, Cs), at 25 °C and XCl concentration of 0.1 mol L(-1), demonstrates that both PMA isomers are strongly associated at low degrees of neutralization, αN (= 0 for aPMA and 0.25 for iPMA), in the presence of all XCls. The shape parameter ρ and the scattering functions suggest that aggregates have the characteristics of microgel particles, with a dense core surrounded by a less dense shell. The extent of aggregation depends on the stereoregular structure of the polymer and on the type of the added cation. Li(+) and Na(+) ions support aggregation better than Cs(+) ions. Besides, iPMA chains are more strongly aggregated than aPMA chains and form particles with a denser core. A model of the aggregation process is suggested for iPMA. At high αN, a slow diffusive process (so-called extraordinary or anomalous mode in diffusion of polyelectrolytes), arising from electrostatic interactions between charged chains, is observed for both PMAs. Results suggest that under the same experimental conditions iPMA is effectively more charged than aPMA. The role of ions in the slow-mode phenomenon is less pronounced than in aggregation. PMID:25137480

  16. Determination of the common and rare alkalies in mineral analysis

    USGS Publications Warehouse

    Wells, R.C.; Stevens, R.E.

    1934-01-01

    Methods are described which afford a determination of each member of the alkali group and are successful in dealing with the quantities of the rare alkalies found in rocks and minerals. The procedures are relatively rapid and based chiefly on the use of chloroplatinic acid, absolute alcohol and ether, and ammonium sulfate. The percentages of all the alkalies found in a number of minerals are given.

  17. Environmental mercury contamination around a chlor-alkali plant

    SciTech Connect

    Lodenius, M.; Tulisalo, E.

    1984-04-01

    The chlor-alkali industry is one of the most important emitters of mercury. This metal is effectively spread from chlor-alkali plants into the atmosphere and it has been reported that only a few percent of the mercury emissions are deposited locally the major part spreading over very large areas. The purpose of this investigation was to study the spreading of mercury up to 100 km from a chlor-alkali plant using three different biological indicators.

  18. Electrochemical devices utilizing molten alkali metal electrode-reactant

    DOEpatents

    Hitchcock, D.C.; Mailhe, C.C.; De Jonghe, L.C.

    1985-07-10

    Electrochemical cells are provided with a reactive metal to reduce the oxide of the alkali metal electrode-reactant. Cells employing a molten alkali metal electrode, e.g., sodium, in contact with a ceramic electrolyte, which is a conductor of the ions of the alkali metal forming the electrode, exhibit a lower resistance when a reactive metal, e.g., vanadium, is allowed to react with and reduce the alkali metal oxide. Such cells exhibit less degradation of the electrolyte and of the glass seals often used to joining the electrolyte to the other components of the cell under cycling conditions.

  19. Electrochemical devices utilizing molten alkali metal electrode-reactant

    DOEpatents

    Hitchcock, David C.; Mailhe, Catherine C.; De Jonghe, Lutgard C.

    1986-01-01

    Electrochemical cells are provided with a reactive metal to reduce the oxide of the alkali metal electrode-reactant. Cells employing a molten alkali metal electrode, e.g., sodium, in contact with a ceramic electrolyte, which is a conductor of the ions of the alkali metal forming the electrode, exhibit a lower resistance when a reactive metal, e.g., vanadium, is allowed to react with and reduce the alkali metal oxide. Such cells exhibit less degradation of the electrolyte and of the glass seals often used to joining the electrolyte to the other components of the cell under cycling conditions.

  20. High cation transport polymer electrolyte

    DOEpatents

    Gerald, II, Rex E.; Rathke, Jerome W.; Klingler, Robert J.

    2007-06-05

    A solid state ion conducting electrolyte and a battery incorporating same. The electrolyte includes a polymer matrix with an alkali metal salt dissolved therein, the salt having an anion with a long or branched chain having not less than 5 carbon or silicon atoms therein. The polymer is preferably a polyether and the salt anion is preferably an alkyl or silyl moiety of from 5 to about 150 carbon/silicon atoms.

  1. Mobility of cations in magnesium aluminate spinel

    NASA Astrophysics Data System (ADS)

    Martinelli, J. R.; Sonder, E.; Weeks, R. A.; Zuhr, R. A.

    1986-04-01

    Transport of cations in magnesium aluminate spinel due to an applied electric field at approximately 1000 °C has been measured by observing changes in elemental concentrations near the cathode and anode surfaces using ion backscattering techniques. The results indicate that magnesium ions are the mobile species at 1000 °C and that these ions combine with ambient oxygen at the cathode surface to form a MgO layer. Quantitative interpretation of the data leads to the conclusion that the ionic transference number of spinel becomes approximately 0.5 after treatment in an electric field.

  2. Star-like superalkali cations featuring planar pentacoordinate carbon

    NASA Astrophysics Data System (ADS)

    Guo, Jin-Chang; Tian, Wen-Juan; Wang, Ying-Jin; Zhao, Xue-Feng; Wu, Yan-Bo; Zhai, Hua-Jin; Li, Si-Dian

    2016-06-01

    Superalkali cations, known to possess low vertical electron affinities (VEAs), high vertical detachment energies, and large highest occupied molecular orbital (HOMO)-lowest unoccupied molecular orbital (LUMO) energy gaps, are intriguing chemical species. Thermodynamically, such species need to be the global minima in order to serve as the promising targets for experimental realization. In this work, we propose the strategies of polyhalogenation and polyalkalination for designing the superalkali cations. By applying these strategies, the local-minimum planar pentacoordinate carbon (ppC) cluster CBe5 can be modified to form a series of star-like superalkali ppC or quasi-ppC CBe5X5+ (X = F, Cl, Br, Li, Na, K) cations containing a CBe5 moiety. Polyhalogenation and polyalkalination on the CBe5 unit may help eliminate the high reactivity of bare CBe5 molecule by covering the reactive Be atoms with noble halogen anions and alkali cations. Computational exploration of the potential energy surfaces reveals that the star-like ppC or quasi-ppC CBe5X5+ (X = F, Cl, Br, Li, Na, K) clusters are the true global minima of the systems. The predicted VEAs for CBe5X5+ range from 3.01 to 3.71 eV for X = F, Cl, Br and 2.12-2.51 eV for X = Li, Na, K, being below the lower bound of the atomic ionization potential of 3.89 eV in the periodic table. Large HOMO-LUMO energy gaps are also revealed for the species: 10.76-11.07 eV for X = F, Cl, Br and 4.99-6.91 eV for X = Li, Na, K. These designer clusters represent the first series of superalkali cations with a ppC center. Bonding analyses show five Be-X-Be three-center two-electron (3c-2e) σ bonds for the peripheral bonding, whereas the central C atom is associated with one 6c-2e π bond and three 6c-2e σ bonds, rendering (π and σ) double aromaticity. Born-Oppenheimer molecular dynamics simulations indicate that the CBe5 motif is robust in the clusters. As planar hypercoordination carbon species are often thermodynamically unstable and

  3. Star-like superalkali cations featuring planar pentacoordinate carbon.

    PubMed

    Guo, Jin-Chang; Tian, Wen-Juan; Wang, Ying-Jin; Zhao, Xue-Feng; Wu, Yan-Bo; Zhai, Hua-Jin; Li, Si-Dian

    2016-06-28

    Superalkali cations, known to possess low vertical electron affinities (VEAs), high vertical detachment energies, and large highest occupied molecular orbital (HOMO)-lowest unoccupied molecular orbital (LUMO) energy gaps, are intriguing chemical species. Thermodynamically, such species need to be the global minima in order to serve as the promising targets for experimental realization. In this work, we propose the strategies of polyhalogenation and polyalkalination for designing the superalkali cations. By applying these strategies, the local-minimum planar pentacoordinate carbon (ppC) cluster CBe5 can be modified to form a series of star-like superalkali ppC or quasi-ppC CBe5X5 (+) (X = F, Cl, Br, Li, Na, K) cations containing a CBe5 moiety. Polyhalogenation and polyalkalination on the CBe5 unit may help eliminate the high reactivity of bare CBe5 molecule by covering the reactive Be atoms with noble halogen anions and alkali cations. Computational exploration of the potential energy surfaces reveals that the star-like ppC or quasi-ppC CBe5X5 (+) (X = F, Cl, Br, Li, Na, K) clusters are the true global minima of the systems. The predicted VEAs for CBe5X5 (+) range from 3.01 to 3.71 eV for X = F, Cl, Br and 2.12-2.51 eV for X = Li, Na, K, being below the lower bound of the atomic ionization potential of 3.89 eV in the periodic table. Large HOMO-LUMO energy gaps are also revealed for the species: 10.76-11.07 eV for X = F, Cl, Br and 4.99-6.91 eV for X = Li, Na, K. These designer clusters represent the first series of superalkali cations with a ppC center. Bonding analyses show five Be-X-Be three-center two-electron (3c-2e) σ bonds for the peripheral bonding, whereas the central C atom is associated with one 6c-2e π bond and three 6c-2e σ bonds, rendering (π and σ) double aromaticity. Born-Oppenheimer molecular dynamics simulations indicate that the CBe5 motif is robust in the clusters. As planar hypercoordination carbon species are often thermodynamically

  4. Electrodes For Alkali-Metal Thermoelectric Converters

    NASA Technical Reports Server (NTRS)

    Williams, Roger M.; Wheeler, Bob L.; Jeffries-Nakamura, Barbara; Lamb, James L.; Bankston, C. Perry; Cole, Terry

    1989-01-01

    Combination of thin, porous electrode and overlying collector grid reduces internal resistance of alkali-metal thermoelectric converter cell. Low resistance of new electrode and grid boosts power density nearly to 1 W/cm2 of electrode area at typical operating temperatures of 1,000 to 1,300 K. Conductive grid encircles electrode film on alumina tube. Bus wire runs along tube to collect electrical current from grid. Such converters used to transform solar, nuclear, and waste heat into electric power.

  5. High power diode pumped alkali vapor lasers

    NASA Astrophysics Data System (ADS)

    Zweiback, J.; Krupke, B.

    2008-05-01

    Diode pumped alkali lasers have developed rapidly since their first demonstration. These lasers offer a path to convert highly efficient, but relatively low brightness, laser diodes into a single high power, high brightness beam. General Atomics has been engaged in the development of DPALs with scalable architectures. We have examined different species and pump characteristics. We show that high absorption can be achieved even when the pump source bandwidth is several times the absorption bandwidth. In addition, we present experimental results for both potassium and rubidium systems pumped with a 0.2 nm bandwidth alexandrite laser. These data show slope efficiencies of 67% and 72% respectively.

  6. Cathode architectures for alkali metal / oxygen batteries

    SciTech Connect

    Visco, Steven J; Nimon, Vitaliy; De Jonghe, Lutgard C; Volfkovich, Yury; Bograchev, Daniil

    2015-01-13

    Electrochemical energy storage devices, such as alkali metal-oxygen battery cells (e.g., non-aqueous lithium-air cells), have a cathode architecture with a porous structure and pore composition that is tailored to improve cell performance, especially as it pertains to one or more of the discharge/charge rate, cycle life, and delivered ampere-hour capacity. A porous cathode architecture having a pore volume that is derived from pores of varying radii wherein the pore size distribution is tailored as a function of the architecture thickness is one way to achieve one or more of the aforementioned cell performance improvements.

  7. Cation Diffusion in Xenotime

    NASA Astrophysics Data System (ADS)

    Cherniak, D. J.

    2004-05-01

    Xenotime is an important mineral in metamorphic paragenesis, and useful in isotopic dating, garnet-xenotime thermometry, and monazite-xenotime thermometry, so diffusion data for xenotime of cations of geochronological and geochemical importance are of some interest. We report here on diffusion of the rare earth elements Sm, Dy and Yb in synthetic xenotime under dry conditions. The synthetic xenotime was grown via a Na2}CO{3}-MoO_{3 flux method. The source of diffusant for the experiments were REE phosphate powders, with experiments run with sources containing a single REE. Experiments were performed by placing source and xenotime in Pt capsules, and annealing capsules in 1 atm furnaces for times ranging from thirty minutes to a month, at temperatures from 1000 to 1400C. The REE distributions in the xenotime were profiled by Rutherford Backscattering Spectrometry (RBS). The following Arrhenius relations are obtained for diffusion in xenotime, normal to (101): DSm = 1.7x10-4 exp(-442 kJ mol-1/RT) m2}sec{-1 DDy = 3.5x10-7 exp(-365 kJ mol-1/RT) m2}sec{-1 DYb = 7.4x10-7 exp(-371 kJ mol-1/RT) m2}sec{-1. Diffusivities of these REE do not differ greatly in xenotime, in contrast to the findings noted for the REE in zircon (Cherniak et al., 1997), where the LREE diffuse more slowly, and with higher activation energies for diffusion, than the heavier rare earths. In zircon, these differences among diffusion of the rare earths are attributed to the relatively large size of the REE with respect to Zr, for which they substitute in the zircon lattice. With the systematic increase in ionic radius from the heavy to lighter REE, this size mismatch becomes more pronounced and diffusivities of the LREE are as consequence slower. Although xenotime is isostructural with zircon, the REE are more closely matched in size to Y, so in xenotime this effect appears much smaller and the REE diffuse at similar rates. In addition, the process of diffusion in xenotime likely involves simple REE+3

  8. Production of concentrated caustic soda and hydrochloride acid solutions from sodium chloride by electrodialysis with the aid of bipolar ion-exchange membranes

    SciTech Connect

    Greben', V.P.; Pivovarov, N.Ya.; Latskov, V.L.

    1988-10-20

    This paper gives a comparative analysis of the action of electrodialyzers containing three and five compartments in the structural unit, and equipped with bipolar, cation-exchange, and anion-exchange membranes, used for production of hydrochloric acid and caustic soda from sodium chloride solutions. It was shown that an electrodialyzer with five compartments gives hydrochloric acid and caustic soda for 2.5-3 M concentration with 0.2-0.3 current efficiency, whereas an electrodialyzer with three compartments in the structural unit gives hydrochloric acid and caustic soda concentrations of about 1.2 M at the same current efficiency. The performance of the electrodialyzers was analyzed and equations were derived for calculating the current efficiencies for acid and alkali under conditions of acidification of the salt solution; this was based on determination of the transport numbers of ions passing through the membranes.

  9. Superconductivity in alkali metal intercalated iron selenides.

    PubMed

    Krzton-Maziopa, A; Svitlyk, V; Pomjakushina, E; Puzniak, R; Conder, K

    2016-07-27

    Alkali metal intercalated iron selenide superconductors A x Fe2-y Se2 (where A  =  K, Rb, Cs, Tl/K, and Tl/Rb) are characterized by several unique properties, which were not revealed in other superconducting materials. The compounds crystallize in overall simple layered structure with FeSe layers intercalated with alkali metal. The structure turned out to be pretty complex as the existing Fe-vacancies order below ~550 K, which further leads to an antiferromagnetic ordering with Néel temperature fairly above room temperature. At even lower temperatures a phase separation is observed. While one of these phases stays magnetic down to the lowest temperatures the second is becoming superconducting below ~30 K. All these effects give rise to complex relationships between the structure, magnetism and superconductivity. In particular the iron vacancy ordering, linked with a long-range magnetic order and a mesoscopic phase separation, is assumed to be an intrinsic property of the system. Since the discovery of superconductivity in those compounds in 2010 they were investigated very extensively. Results of the studies conducted using a variety of experimental techniques and performed during the last five years were published in hundreds of reports. The present paper reviews scientific work concerning methods of synthesis and crystal growth, structural and superconducting properties as well as pressure investigations. PMID:27248118

  10. Durability of Alkali Activated Blast Furnace Slag

    NASA Astrophysics Data System (ADS)

    Ellis, K.; Alharbi, N.; Matheu, P. S.; Varela, B.; Hailstone, R.

    2015-11-01

    The alkali activation of blast furnace slag has the potential to reduce the environmental impact of cementitious materials and to be applied in geographic zones where weather is a factor that negatively affects performance of materials based on Ordinary Portland Cement. The scientific literature provides many examples of alkali activated slag with high compressive strengths; however research into the durability and resistance to aggressive environments is still necessary for applications in harsh weather conditions. In this study two design mixes of blast furnace slag with mine tailings were activated with a potassium based solution. The design mixes were characterized by scanning electron microscopy, BET analysis and compressive strength testing. Freeze-thaw testing up to 100 freeze-thaw cycles was performed in 10% road salt solution. Our findings included compressive strength of up to 100 MPa after 28 days of curing and 120 MPa after freeze-thaw testing. The relationship between pore size, compressive strength, and compressive strength after freeze-thaw was explored.

  11. Superconductivity in alkali metal intercalated iron selenides

    NASA Astrophysics Data System (ADS)

    Krzton-Maziopa, A.; Svitlyk, V.; Pomjakushina, E.; Puzniak, R.; Conder, K.

    2016-07-01

    Alkali metal intercalated iron selenide superconductors A x Fe2‑y Se2 (where A  =  K, Rb, Cs, Tl/K, and Tl/Rb) are characterized by several unique properties, which were not revealed in other superconducting materials. The compounds crystallize in overall simple layered structure with FeSe layers intercalated with alkali metal. The structure turned out to be pretty complex as the existing Fe-vacancies order below ~550 K, which further leads to an antiferromagnetic ordering with Néel temperature fairly above room temperature. At even lower temperatures a phase separation is observed. While one of these phases stays magnetic down to the lowest temperatures the second is becoming superconducting below ~30 K. All these effects give rise to complex relationships between the structure, magnetism and superconductivity. In particular the iron vacancy ordering, linked with a long-range magnetic order and a mesoscopic phase separation, is assumed to be an intrinsic property of the system. Since the discovery of superconductivity in those compounds in 2010 they were investigated very extensively. Results of the studies conducted using a variety of experimental techniques and performed during the last five years were published in hundreds of reports. The present paper reviews scientific work concerning methods of synthesis and crystal growth, structural and superconducting properties as well as pressure investigations.

  12. Unconventional Superconductivity of Alkali-doped Fullerenes

    NASA Astrophysics Data System (ADS)

    Potocnik, Anton; Krajnc, Andraz; Jeglic, Peter; Prassides, Kosmas; Rosseinsky, Matthew J.; Arcon, Denis

    2014-03-01

    The superconductivity of the alkali-doped fullerenes (A3C60, A = alkali metal) has been so far discussed within the standard theory of superconductivity developed by Bardeen, Cooper and Shrieffer (BCS), even thought, they exhibit relatively high critical temperatures (up to Tc = 32 K). However, after our recent high-pressure measurements on Cs3C60 such description became questionable. We have shown that the superconducting phase of A3C60, in fact, borders the antiferromagnetic insulating phase (AFI), commonly observed for high-temperature superconductors like cuprates or pnictides. In addition, we also increased the maximal Tc to 38 K. To investigate this peculiar superconductivity close to the border with AFI state we employed nuclear magnetic resonance technique on Cs3-xRbxC60 and on Cs3C60 at various high pressures. Our results could not be correctly explained either by the standard BCS or the extended BCS that includes electron-electron repulsion interaction - the Migdal-Eliashberg theory. Far better agreement is obtained by the Dynamical Mean Field Theory. Due to similarity with other unconventional superconductors these results could also be relevant to other unconventional high-temperature superconductors.

  13. Dynamics of reactive ultracold alkali polar molecules

    NASA Astrophysics Data System (ADS)

    Quéméner, Goulven; Bohn, John; Petrov, Alexander; Kotochigova, Svetlana

    2011-05-01

    Recently, ultracold polar molecules of KRb have been created. These molecules are chemically reactive and their lifetime in a trap is limited. However, their lifetime increases when they are loaded into a 1D optical lattice in the presence of an electric field. These results naturally raise the question of manipulating ultracold collisions of other species of alkali dimer molecules, with an eye toward both novel stereochemistry, as well as suppressing unwanted reactions, to enable condensed matter applications. In this talk, we report on a comparative study between the bi-alkali polar molecules of LiNa, LiK, LiRb, LiCs which have been predicted to be reactive. We compute the isotropic C6 coefficients of these systems and we predict the elastic and reactive rate coefficients when an electric field is applied in a 1D optical lattice. We will discuss the efficacy of evaporative cooling for each species. This work was supported by a MURI-AFOSR grant.

  14. Lithium tracer-diffusion in an alkali-basaltic melt — An ion-microprobe determination

    NASA Astrophysics Data System (ADS)

    Lowry, R. K.; Reed, S. J. B.; Nolan, J.; Henderson, P.; Long, J. V. P.

    1981-03-01

    An ion-microprobe-based technique has been used to measure lithium tracer-diffusion coefficients ( D Li) in an alkali-basaltic melt at 1300, 1350 and 1400°C. The results can be expressed in the form: D Li=7.5 ×10 -2exp(-27,600/RT)cm 2S -1 The results show significantly faster diffusion rates than those previously recorded for other monovalent, divalent and trivalent cations in a tholeiitic melt. Consequently, diffusive transport of ions acting over a given time in a basaltic melt can produce a wider range of transport distance values than hitherto supposed. Hence, it is concluded that great care should be exercised when applying diffusion data to petrological problems.

  15. Fluorescent probes and bioimaging: alkali metals, alkaline earth metals and pH.

    PubMed

    Yin, Jun; Hu, Ying; Yoon, Juyoung

    2015-07-21

    All living species and life forms have an absolute requirement for bio-functional metals and acid-base equilibrium chemistry owing to the critical roles they play in biological processes. Hence, a great need exists for efficient methods to detect and monitor biometals and acids. In the last few years, great attention has been paid to the development of organic molecule based fluorescent chemosensors. The availability of new synthetic fluorescent probes has made fluorescence microscopy an indispensable tool for tracing biologically important molecules and in the area of clinical diagnostics. This review highlights the recent advances that have been made in the design and bioimaging applications of fluorescent probes for alkali metals and alkaline earth metal cations, including lithium, sodium and potassium, magnesium and calcium, and for pH determination within biological systems. PMID:25317749

  16. Low-frequency dynamics of aqueous alkali chloride solutions as probed by terahertz spectroscopy

    NASA Astrophysics Data System (ADS)

    Kann, Z. R.; Skinner, J. L.

    2016-06-01

    Terahertz (far infrared) spectroscopy provides a useful tool for probing both ionic motions in solution and the effect of ionic solutes on the dynamics of the solvent. In this study, we calculate terahertz spectra of aqueous alkali chloride solutions using classical but novel (the water model includes three-body interactions, the ion parameterization is non-standard, and the dipole surface is polarizable) molecular dynamics simulations. The calculated spectra compare reasonably well to experimental spectra. Decomposition of the calculated spectra is used to gain a deeper understanding of the physical phenomena underlying the spectra and the connection to, for instance, the vibrational density of states for the ions. The decomposed results are also used to explain many of the cation-dependent trends observed in the experimental spectra.

  17. Cationic polyelectrolyte-stabilized nanoparticles via RAFT aqueous dispersion polymerization.

    PubMed

    Semsarilar, M; Ladmiral, V; Blanazs, A; Armes, S P

    2013-06-18

    We report the synthesis of cationic sterically stabilized diblock copolymer nanoparticles via polymerization-induced self-assembly (PISA) using a RAFT aqueous dispersion polymerization formulation. The cationic steric stabilizer is a macromolecular chain-transfer agent (macro-CTA) based on quaternized poly(2-(dimethylamino)ethyl methacrylate) (PQDMA), and the hydrophobic core-forming block is based on poly(2-hydroxypropyl methacrylate) (PHPMA). The effect of varying synthesis parameters such as the salt concentration, solids content, relative block composition, and cationic charge density has been studied. In the absence of salt, self-assembly is problematic because of the strong repulsion between the highly cationic PQDMA stabilizer chains. However, in the presence of salt this problem can be overcome by reducing the charge density within the coronal stabilizer layer by either (i) statistically copolymerizing QDMA monomer with a nonionic comonomer (e.g., glycerol monomethacrylate, GMA) or (ii) using a binary mixture of a PQDMA macro-CTA and a poly(glycerol monomethacrylate) (PGMA) macro-CTA. These cationic diblock copolymer nanoparticles were analyzed by (1)H NMR spectroscopy, dynamic light scattering (DLS), transmission electron microscopy (TEM), and aqueous electrophoresis. NMR studies suggest that the HPMA polymerization is complete within 2 h at 70 °C. Depending on the specific reaction conditions, either spherical, wormlike or vesicular nanoparticles can be prepared with tunable cationic surface charge. PMID:23205729

  18. Photochemical generation, isomerization, and oxygenation of stilbene cation radicals

    SciTech Connect

    Lewis, F.D.; Bedell, A.M.; Dykstra, R.E.; Elbert, J.E. ); Gould, I.R.; Farid, S. )

    1990-10-24

    The cation radicals of cis- and trans-stilbene and several of their ring-substituted derivatives have been generated in solution directly by means of pulsed-laser-induced electron transfer to singlet cyanoanthracenes or indirectly via electron transfer from biphenyl to the singlet cyanoanthracene followed by secondary electron transfer from the stilbenes to the biphenyl cation radical. Transient absorption spectra of the cis- and trans-stilbene cation radicals generated by secondary electron transfer are similar to those previously obtained in 77 K matrices. Quantum yields for radical ion-pair cage escape have been measured for direct electron transfer from the stilbenes to three neutral and one charged singlet acceptor. These values increase as the ion-pair energy increases due to decreased rate constants for radical ion-pair return electron transfer, in accord with the predictions of Marcus theory for highly exergonic electron transfer. Cage-escape efficiencies are larger for trans- vs cis-stilbene cation radicals, possibly due to the greater extent of charge delocalization in the planar trans vs nonpolar cis cation radicals. Cage-escape stilbene cation radicals can initiate a concentration-dependent one way cis- {yields} trans-stilbene isomerization reaction.

  19. 40 CFR 721.8900 - Substituted halogenated pyridinol, alkali salt.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ..., alkali salt. 721.8900 Section 721.8900 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.8900 Substituted halogenated pyridinol, alkali salt. (a) Chemical..., chemical destruction and carbon adsorption. (iv) Release to water. Requirements as specified in § 721.90...

  20. Formation of lysinoalanine in egg white under alkali treatment.

    PubMed

    Zhao, Yan; Luo, Xuying; Li, Jianke; Xu, Mingsheng; Tu, Yonggang

    2016-03-01

    To investigate the formation mechanism of lysinoalanine (LAL) in eggs during the alkali treatment process, NaOH was used for the direct alkali treatment of egg white, ovalbumin, and amino acids; in addition, the amount of LAL formed during the alkali treatment process was measured. The results showed that the alkali treatment resulted in the formation of LAL in the egg white. The LAL content increased with increasing pH and temperature, with the LAL content first increasing and then leveling off with increasing time. The amount of LAL formed in the ovalbumin under the alkali treatment condition accounted for approximately 50.51% to 58.68% of the amount of LAL formed in the egg white. Thus, the LAL formed in the ovalbumin was the main source for the LAL in the egg white during the alkali treatment process. Under the alkali treatment condition, free L-serine, L-cysteine, and L-cystine reacted with L-lysine to form LAL; therefore, they are the precursor amino acids of LAL formed in eggs during the alkali treatment process. PMID:26772660

  1. 40 CFR 721.4740 - Alkali metal nitrites.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... defined in 40 CFR 721.3) containing amines. (b) ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Alkali metal nitrites. 721.4740... Substances § 721.4740 Alkali metal nitrites. (a) Chemical substances and significant new use subject...

  2. 40 CFR 721.4740 - Alkali metal nitrites.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... defined in 40 CFR 721.3) containing amines. (b) ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Alkali metal nitrites. 721.4740... Substances § 721.4740 Alkali metal nitrites. (a) Chemical substances and significant new use subject...

  3. 40 CFR 721.4740 - Alkali metal nitrites.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... defined in 40 CFR 721.3) containing amines. (b) ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Alkali metal nitrites. 721.4740... Substances § 721.4740 Alkali metal nitrites. (a) Chemical substances and significant new use subject...

  4. 40 CFR 721.4740 - Alkali metal nitrites.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... defined in 40 CFR 721.3) containing amines. (b) ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Alkali metal nitrites. 721.4740... Substances § 721.4740 Alkali metal nitrites. (a) Chemical substances and significant new use subject...

  5. Self-discharge in bimetallic cells containing alkali metal

    NASA Technical Reports Server (NTRS)

    Foster, M. S.; Hesson, J. C.; Shimotake, H.

    1969-01-01

    Theoretical analysis of thermally regenerative bimetallic cells with alkali metal anodes shows a relation between the current drawn and the rate of discharge under open-circuit conditions. The self-discharge rate of the cell is due to the dissolution and ionization of alkali metal atoms in the fused-salt electrolyte

  6. COMPLEX FLUORIDES OF PLUTONIUM AND AN ALKALI METAL

    DOEpatents

    Seaborg, G.T.

    1960-08-01

    A method is given for precipitating alkali metal plutonium fluorides. such as KPuF/sub 5/, KPu/sub 2/F/sub 9/, NaPuF/sub 5/, and RbPuF/sub 5/, from an aqueous plutonium(IV) solution by adding hydrogen fluoride and alkali-metal- fluoride.

  7. 40 CFR 721.4740 - Alkali metal nitrites.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.4740 Alkali metal nitrites. (a) Chemical substances and significant new use subject to reporting. (1) The category of chemical substances which are nitrites of the alkali metals (Group IA in...

  8. 40 CFR 721.1878 - Alkali metal alkyl borohydride (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ...) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.1878 Alkali metal alkyl borohydride (generic). (a) Chemical substance... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Alkali metal alkyl...

  9. Potential energy curves via double electron-attachment calculations: Dissociation of alkali metal dimers

    NASA Astrophysics Data System (ADS)

    Musiał, Monika; Kowalska-Szojda, Katarzyna; Lyakh, Dmitry I.; Bartlett, Rodney J.

    2013-05-01

    The recently developed method [M. Musiał, J. Chem. Phys. 136, 134111 (2012), 10.1063/1.3700438] to study double electron attached states has been applied to the description of the ground and excited state potential energy curves of the alkali metal dimers. The method is based on the multireference coupled cluster scheme formulated within the Fock space formalism for the (2,0) sector. Due to the use of the efficient intermediate Hamiltonian formulation, the approach is free from the intruder states problem. The description of the neutral alkali metal dimers is accomplished via attaching two electrons to the corresponding doubly ionized system. This way is particularly advantageous when a closed shell molecule dissociates into open shell subunits while its doubly positive cation generates the closed shell fragments. In the current work, we generate the potential energy curves for the ground and multiple excited states of the Li2 and Na2 molecules. In all cases the potential energy curves are smooth for the entire range of interatomic distances (from the equilibrium point to the dissociation limit). Based on the calculated potential energy curves, we are able to compute spectroscopic parameters of the systems studied.

  10. Alkali metal control over N-N cleavage in iron complexes.

    PubMed

    Grubel, Katarzyna; Brennessel, William W; Mercado, Brandon Q; Holland, Patrick L

    2014-12-01

    Though N2 cleavage on K-promoted Fe surfaces is important in the large-scale Haber-Bosch process, there is still ambiguity about the number of Fe atoms involved during the N-N cleaving step and the interactions responsible for the promoting ability of K. This work explores a molecular Fe system for N2 reduction, particularly focusing on the differences in the results obtained using different alkali metals as reductants (Na, K, Rb, Cs). The products of these reactions feature new types of Fe-N2 and Fe-nitride cores. Surprisingly, adding more equivalents of reductant to the system gives a product in which the N-N bond is not cleaved, indicating that the reducing power is not the most important factor that determines the extent of N2 activation. On the other hand, the results suggest that the size of the alkali metal cation can control the number of Fe atoms that can approach N2, which in turn controls the ability to achieve N2 cleavage. The accumulated results indicate that cleaving the triple N-N bond to nitrides is facilitated by simultaneous approach of least three low-valent Fe atoms to a single molecule of N2. PMID:25412468

  11. Alkali and transition metal (Ag, Cu) salts of bridged 5-nitrotetrazole derivatives for energetic applications.

    PubMed

    Klapötke, Thomas M; Sabaté, Carles Miró; Rasp, Matthias

    2009-03-14

    A family of energetic salts based on the novel 5-(5-nitrotetrazole-2-ylmethyl)-tetrazolate anion (NTTz(-)) with alkali metals (Li(+), Na(+), K(+), Rb(+) and Cs(+)) were synthesized by the reaction of the free acid 5-(5-nitrotetrazole-2-ylmethyl)-tetrazole with a suitable alkali metal base (bicarbonate or carbonate) in alcohol or water. The sodium salt () was, in turn, used to form salts containing the NTTz(-) anion and Ag(+) () or Cu(2+) (, and ) cations. The new compounds were characterized by IR, Raman and NMR spectroscopy, mass spectroscopy, elemental analysis and differential scanning calorimetry (DSC). In addition, the solid-state structure of the NTTz(-) anion was determined by diffraction methods using X-ray analysis. We also assessed the energetic properties of the compounds using standardized (BAM) tests. Interestingly, the silver and copper salts are easily and safely initiated by the laser beam generated by a Raman machine and some of the compounds reported here have promising properties for applications as a new class of nitrogen-rich, more environmentally-friendly energetic materials. PMID:19240918

  12. Alkali Metal Control over N–N Cleavage in Iron Complexes

    PubMed Central

    2015-01-01

    Though N2 cleavage on K-promoted Fe surfaces is important in the large-scale Haber–Bosch process, there is still ambiguity about the number of Fe atoms involved during the N–N cleaving step and the interactions responsible for the promoting ability of K. This work explores a molecular Fe system for N2 reduction, particularly focusing on the differences in the results obtained using different alkali metals as reductants (Na, K, Rb, Cs). The products of these reactions feature new types of Fe–N2 and Fe-nitride cores. Surprisingly, adding more equivalents of reductant to the system gives a product in which the N–N bond is not cleaved, indicating that the reducing power is not the most important factor that determines the extent of N2 activation. On the other hand, the results suggest that the size of the alkali metal cation can control the number of Fe atoms that can approach N2, which in turn controls the ability to achieve N2 cleavage. The accumulated results indicate that cleaving the triple N–N bond to nitrides is facilitated by simultaneous approach of least three low-valent Fe atoms to a single molecule of N2. PMID:25412468

  13. Shallow electron traps in alkali halide crystals: Mollwo-Ivey relations of the optical absorption bands

    NASA Astrophysics Data System (ADS)

    Ziraps, Valters

    2001-03-01

    Evidences are given that two classes of the transient IR- absorption bands: (a) with max. at 0.27-0.36 eV in NaCl, KCl, KBr, KI and RbCl (due to shallow electron traps according G. Jacobs or due to bound polarons according E.V. Korovkin and T.A. Lebedkina) and (b) with max. at 0.15-0.36 eV in NaI, NaBr, NaCl:I, KCl:I, RbCl:I and RbBr:I (due to on-center STE localized at iodine dimer according M. Hirai and collaborators) are caused by the same defect- atomic alkali impurity center [M+]c0e- (electron e- trapped by a substitutional smaller size alkali cation impurity [M+]c0). The Mollwo-Ivey plots (for the transient IR-absorption bands) of the zero-phonon line energy E0 (for NaCl, KCl, KBr, RbCl and NaBr, KCl:I) and/or the low-energy edge valued E0 (for NaI, RbCl:I, RbBr:I) versus anion-cation distance (d) evidence that two types of the [M+]c0e- centers are predominant: (a) [Na+]c0e- in the KX and RbX host crystals with the relation E0approximately equals 6.15/d2.74, (b) [Li+]c03- in the NaX host crystals - E0approximately equals 29.4/d4.72. The Mollwo-Ivey relation E0approximately equals 18.36/d(superscript 2.70 is fulfilled as well for the F' band in NaCl, KCl, KBr, KI, RbCl, RbI if we use the F' center optical binding energy values E0.

  14. Effects of alkali treatments on Ag nanowire transparent conductive films

    NASA Astrophysics Data System (ADS)

    Kim, Sunho; Kang, Jun-gu; Eom, Tae-yil; Moon, Bongjin; Lee, Hoo-Jeong

    2016-06-01

    In this study, we employ various alkali materials (alkali metals with different base strengths, and ammonia gas and solution) to improve the conductivity of silver nanowire (Ag NW)-networked films. The alkali treatment appears to remove the surface oxide and improve the conductivity. When applied with TiO2 nanoparticles, the treatment appears more effective as the alkalis gather around wire junctions and help them weld to each other via heat emitted from the reduction reaction. The ammonia solution treatment is found to be quick and aggressive, damaging the wires severely in the case of excessive treatment. On the other hand, the ammonia gas treatment seems much less aggressive and does not damage the wires even after a long exposure. The results of this study highlight the effectiveness of the alkali treatment in improving of the conductivity of Ag NW-networked transparent conductive films.

  15. Performance of Straight Steel Fibres Reinforced Alkali Activated Concrete

    NASA Astrophysics Data System (ADS)

    Faris, Meor Ahmad; Bakri Abdullah, Mohd Mustafa Al; Nizar Ismail, Khairul; Muniandy, Ratnasamy; Putra Jaya, Ramadhansyah

    2016-06-01

    This paper focus on the performance of alkali activated concrete produced by using fly ash activated by sodium silicate and sodium hydroxide solutions. These alkali activated concrete were reinforced with straight steel fibres with different weight percentage starting from 0 % up to 5 %. Chemical composition of raw material in the production alkali activated concrete which is fly ash was first identified by using X-ray fluorescence. Results reveal there have an effect of straight steel fibres inclusion to the alkali activated concrete. Highest compressive strength of alkali activated concrete which is 67.72 MPa was obtained when 3 % of straight fibres were added. As well as flexural strength, highest flexural strength which is 6.78 MPa was obtained at 3 % of straight steel fibres inclusions.

  16. Impact of Alkali Source on Vitrification of SRS High Level Waste

    SciTech Connect

    LAMBERT, D. P.; MILLER, D. H.; PEELER, D. K.; SMITH, M. E.; STONE, M. E.

    2005-09-08

    The Defense Waste Processing Facility (DWPF) Savannah River Site is currently immobilizing high level nuclear waste sludge by vitrification in borosilicate glass. The processing strategy involves blending a large batch of sludge into a feed tank, washing the sludge to reduce the amount of soluble species, then processing the large ''sludge batch'' through the DWPF. Each sludge batch is tested by the Savannah River National Laboratory (SRNL) using simulants and tests with samples of the radioactive waste to ''qualify'' the batch prior to processing in the DWPF. The DWPF pretreats the sludge by first acidifying the sludge with nitric and formic acid. The ratio of nitric to formic acid is adjusted as required to target a final glass composition that is slightly reducing (the target is for {approx}20% of the iron to have a valence of two in the glass). The formic acid reduces the mercury in the feed to elemental mercury which is steam stripped from the feed. After a concentration step, the glass former (glass frit) is added as a 50 wt% slurry and the batch is concentrated to approximately 50 wt% solids. The feed slurry is then fed to a joule heated melter maintained at 1150 C. The glass must meet both processing (e.g., viscosity and liquidus temperature) and product performance (e.g., durability) constraints The alkali content of the final waste glass is a critical parameter that affects key glass properties (such as durability) as well as the processing characteristics of the waste sludge during the pretreatment and vitrification processes. Increasing the alkali content of the glass has been shown to improve the production rate of the DWPF, but the total alkali in the final glass is limited by constraints on glass durability and viscosity. Two sources of alkali contribute to the final alkali content of the glass: sodium salts in the waste supernate and sodium and lithium oxides in the glass frit added during pretreatment processes. Sodium salts in the waste supernate

  17. Water and magmas: insights about the water solution mechanisms in alkali silicate melts from infrared, Raman, and 29Si solid-state NMR spectroscopies

    NASA Astrophysics Data System (ADS)

    Le Losq, Charles; Mysen, Bjorn O.; Cody, George D.

    2015-12-01

    Degassing of water during the ascent of hydrous magma in a volcanic edifice produces dramatic changes in the magma density and viscosity. This can profoundly affect the dynamics of volcanic eruptions. The water exsolution history, in turn, is driven by the water solubility and solution mechanisms in the silicate melt. Previous studies pointed to dissolved water in silicate glasses and melts existing as molecules (H2Omol species) and hydroxyl groups, OH. These latter OH groups commonly are considered bonded to Si4+ but may form other bonds, such as with alkali or alkaline-earth cations, for instance. Those forms of bonding influence the structure of hydrous melts in different ways and, therefore, their properties. As a result, exsolution of water from magmas may have different eruptive consequences depending on the initial bonding mechanisms of the dissolved water. However, despite their importance, the solution mechanisms of water in silicate melts are not clear. In particular, how chemical composition of melts affects water solubility and solution mechanism is not well understood. In the present experimental study, components of such information are reported via determination of how water interacts with the cationic network of alkali (Li, Na, and K) silicate quenched melts. Results from 29Si single-pulse magic-angle spinning nuclear magnetic resonance (29Si SP MAS NMR), infrared, and Raman spectroscopies show that decreasing the ionic radius of alkali metal cation in silicate melts results in decreasing fraction of water dissolved as OH groups. The nature of OH bonding also changes as the alkali ionic radius changes. Therefore, as the speciation and bonding of water controls the degree of polymerization of melts, water will have different effects on the transport properties of silicate melts depending on their chemical composition. This conclusion, in turn, may affect volcanic phenomena related to the viscous relaxation of hydrous magmas, such as for instance the

  18. Cation Uptake and Allocation by Red Pine Seedlings under Cation-Nutrient Stress in a Column Growth Experiment

    SciTech Connect

    Shi, Zhenqing; Balogh-Brunstad, Zsuzsanna; Grant, Michael R.; Harsh, James B.; Gill, Richard; Thomashow, Linda; Dohnalkova, Alice; Stacks, Daryl; Letourneau, Melissa; Keller, Chester K.

    2014-01-10

    Background and Aims Plant nutrient uptake is affected by environmental stress, but how plants respond to cation-nutrient stress is poorly understood. We assessed the impact of varying degrees of cation-nutrient limitation on cation uptake in an experimental plant-mineral system. Methods Column experiments, with red pine (Pinus resinosa Ait.) seedlings growing in sand/mineral mixtures, were conducted for up to nine months under a range of Ca- and K-limited conditions. The Ca and K were supplied from both minerals and nutrient solutions with varying Ca and K concentrations. Results Cation nutrient stress had little impact on carbon allocation after nine months of plant growth and K was the limiting nutrient for biomass production. The Ca/Sr and K/Rb ratio results allowed independent estimation of dissolution incongruency and discrimination against Sr and Rb during cation uptake processes. The fraction of K in biomass from biotite increased with decreasing K supply from nutrient solutions. The mineral anorthite was consistently the major source of Ca, regardless of nutrient treatment. Conclusions Red pine seedlings exploited more mineral K in response to more severe K deficiency. This did not occur for Ca. Plant discrimination factors must be carefully considered to accurately identify nutrient sources using cation tracers.

  19. Cation Ordering in Layered Nickelates

    NASA Astrophysics Data System (ADS)

    Nelson-Cheeseman, Brittany; Zhou, Hua; Cammarata, Antonio; Hoffman, Jason; Balachandran, Prasanna; Rondinelli, James; Bhattacharya, Anand

    2013-03-01

    The single layer Ruddlesden-Popper nickelates present a model system to understand how the effects of digital dopant cation ordering may affect the properties of 2-dimensional conducting sheets. We investigate the effects of aliovalent A-site cation order on LaSrNiO4 films. Using molecular beam epitaxy, we interleave full layers of SrO and LaO in a series of chemically equivalent films, varying the pattern of SrO and LaO layers relative to the NiO2 layers. Through synchrotron surface x-ray diffraction and Coherant Bragg Rod Analysis (COBRA), we directly investigate the A-site cation order and the resulting atomic displacements for each ordering pattern. We correlate these results with theoretical calculations and transport measurements of the layered nickelate films.

  20. Diversity and Mechanisms of Alkali Tolerance in Lactobacilli▿

    PubMed Central

    Sawatari, Yuki; Yokota, Atsushi

    2007-01-01

    We determined the maximum pH that allows growth (pHmax) for 34 strains of lactobacilli. High alkali tolerance was exhibited by strains of Lactobacillus casei, L. paracasei subsp. tolerans, L. paracasei subsp. paracasei, L. curvatus, L. pentosus, and L. plantarum that originated from plant material, with pHmax values between 8.5 and 8.9. Among these, L. casei NRIC 1917 and L. paracasei subsp. tolerans NRIC 1940 showed the highest pHmax, at 8.9. Digestive tract isolates of L. gasseri, L. johnsonii, L. reuteri, L. salivarius subsp. salicinius, and L. salivarius subsp. salivarius exhibited moderate alkali tolerance, with pHmax values between 8.1 and 8.5. Dairy isolates of L. delbrueckii subsp. bulgaricus, L. delbrueckii subsp. lactis, and L. helveticus exhibited no alkali tolerance, with pHmax values between 6.7 and 7.1. Measurement of the internal pH of representative strains revealed the formation of transmembrane proton gradients (ΔpH) in a reversed direction (i.e., acidic interior) at alkaline external-pH ranges, regardless of their degrees of alkali tolerance. Thus, the reversed ΔpH did not determine alkali tolerance diversity. However, the ΔpH contributed to alkali tolerance, as the pHmax values of several strains decreased with the addition of nigericin, which dissipates ΔpH. Although neutral external-pH values resulted in the highest glycolysis activity in the presence of nigericin regardless of alkali tolerance, substantial glucose utilization was still detected in the alkali-tolerant strains, even in a pH range of between 8.0 and 8.5, at which the remaining strains lost most activity. Therefore, the alkali tolerance of glycolysis reactions contributes greatly to the determination of alkali tolerance diversity. PMID:17449704

  1. Hydrology of Alkali Creek and Castle Valley Ridge coal-lease tracts, central Utah, and potential effects of coal mining

    USGS Publications Warehouse

    Seiler, R.L.; Baskin, R.L.

    1988-01-01

    The Alkali Creek coal-lease tract includes about 2,150 acres in the Book Cliffs coal field in central Utah, and the Castle Valley Ridge coal-lease tract includes about 3,360 acres in the Wasatch Plateau coal field, also in central Utah. Both the Alkali Creek and Castle Valley Ridge coal-lease tracts are near areas where coal is currently (1987) mined by underground methods from the Cretaceous Blackhawk Formation. The Alkali Creek and Castle Valley Ridge areas have intermittent streams in which flow after snowmelt runoff is locally sustained into midsummer by springflow. The only perennial stream is South Fork Corner Canyon Creek in the Castle Valley Ridge area. Peak flow in both areas generally is from snowmelt runoff; however, peak flow from thunderstorm runoff in the Alkali Creek area can exceed that from snowmelt runoff. Estimated annual source-area sediment yield was 0.5 acre-ft/sq mi in the Alkali Creek lease tract and it was 0.3 acre-ft/sq mi in the Castle Valley Ridge lease tract. Groundwater in the Alkali Creek area occurs in perched aquifers in the Flagstaff Limestone and in other formations above the coal-bearing Blackhawk Formation. The principal source of recharge to the aquifers is snowmelt on outcrops. Faults may be major conduits and control the movement of groundwater. Groundwater discharges at formation contacts, between zones of differing permeability within a formation, near faults and into mines. Water sampled from 13 springs in the Alkali Creek area contained dissolved solids at concentrations ranging from 273 to 5,210 mg/L. Water sampled from 17 springs in the Castle Valley Ridge area contained dissolved solids at concentrations ranging from 208 to 579 mg/L. The composition of water from a recently abandoned part of an active mine the Wasatch Plateau closely resembles that of water discharging from a nearby mine that has been abandoned for more than 30 years. Mining of the Alkali Creek and Castle Valley Ridge coal-lease tracts likely will

  2. Strength and durability performance of alkali-activated rice husk ash geopolymer mortar.

    PubMed

    Kim, Yun Yong; Lee, Byung-Jae; Saraswathy, Velu; Kwon, Seung-Jun

    2014-01-01

    This paper describes the experimental investigation carried out to develop the geopolymer concrete based on alkali-activated rice husk ash (RHA) by sodium hydroxide with sodium silicate. Effect on method of curing and concentration of NaOH on compressive strength as well as the optimum mix proportion of geopolymer mortar was investigated. It is possible to achieve compressive strengths of 31 N/mm(2) and 45 N/mm(2), respectively for the 10 M alkali-activated geopolymer mortar after 7 and 28 days of casting when cured for 24 hours at 60°C. Results indicated that the increase in curing period and concentration of alkali activator increased the compressive strength. Durability studies were carried out in acid and sulfate media such as H2SO4, HCl, Na2SO4, and MgSO4 environments and found that geopolymer concrete showed very less weight loss when compared to steam-cured mortar specimens. In addition, fluorescent optical microscopy and X-ray diffraction (XRD) studies have shown the formation of new peaks and enhanced the polymerization reaction which is responsible for strength development and hence RHA has great potential as a substitute for ordinary Portland cement concrete. PMID:25506063

  3. Strength and Durability Performance of Alkali-Activated Rice Husk Ash Geopolymer Mortar

    PubMed Central

    Kim, Yun Yong; Lee, Byung-Jae; Saraswathy, Velu

    2014-01-01

    This paper describes the experimental investigation carried out to develop the geopolymer concrete based on alkali-activated rice husk ash (RHA) by sodium hydroxide with sodium silicate. Effect on method of curing and concentration of NaOH on compressive strength as well as the optimum mix proportion of geopolymer mortar was investigated. It is possible to achieve compressive strengths of 31 N/mm2 and 45 N/mm2, respectively for the 10 M alkali-activated geopolymer mortar after 7 and 28 days of casting when cured for 24 hours at 60°C. Results indicated that the increase in curing period and concentration of alkali activator increased the compressive strength. Durability studies were carried out in acid and sulfate media such as H2SO4, HCl, Na2SO4, and MgSO4 environments and found that geopolymer concrete showed very less weight loss when compared to steam-cured mortar specimens. In addition, fluorescent optical microscopy and X-ray diffraction (XRD) studies have shown the formation of new peaks and enhanced the polymerization reaction which is responsible for strength development and hence RHA has great potential as a substitute for ordinary Portland cement concrete. PMID:25506063

  4. Post-Harvest Processing Methods for Reduction of Silica and Alkali Metals in Wheat Straw

    SciTech Connect

    Thompson, David Neal; Lacey, Jeffrey Alan; Shaw, Peter Gordon

    2002-04-01

    Silica and alkali metals in wheat straw limit its use for bioenergy and gasification. Slag deposits occur via the eutectic melting of SiO2 with K2O, trapping chlorides at surfaces and causing corrosion. A minimum melting point of 950°C is desirable, corresponding to SiO2:K2O of about 3:1. Mild chemical treatments were used to reduce Si, K, and Cl, while varying temperature, concentration, %-solids, and time. Dilute acid was more effective at removing K and Cl, while dilute alkali was more effective for Si. Reduction of minerals in this manner may prove economical for increasing utilization of the straw for combustion or gasification.

  5. Technical report for the alkali lake ecological assessment, phase 1 reconnaissance (FY 91 and FY 92)

    SciTech Connect

    Linder, G.

    1993-03-01

    The report summarizes the results of three field survey trips (June and September 1991, May 1992) taken to investigate the ecological effects associated with the release of over a million gallons of hazardous waste from herbicide production on the Alkali Lake playa. Sampling of soil, sediment, groundwater, soil-dwelling invertebrates and vegetation confirmed that hazardous materials from the waste disposal area are migrating westerly within the shallow aquifer to West Alkali Lake. Two areas of dead vegetation were identified and permanently marked to determine if these areas are changing in size and location. Preliminary calculations using a linear food-chain model suggested that small mammalian herbivores would probably not display adverse effects due to dietary exposures to the contaminants. However, nestling shorebirds may be exposed to concentrations potentially associated with adverse biological effects.

  6. Elastic properties of alkali-feldspars

    NASA Astrophysics Data System (ADS)

    Waeselmann, N.; Brown, J.; Angel, R. J.; Ross, N.; Kaminsky, W.

    2013-12-01

    New measurements of single crystal elastic moduli for a suite of the alkali feldspars are reported. In order to interpret Earth's seismic structure, knowledge of the elastic properties of constituent minerals is essential. The elasticity of feldspar minerals, despite being the most abundant phase in Earth's crust (estimated to be more than 60%), were previously poorly characterized. All prior seismic and petrologic studies have utilized 50-year-old results, of questionable quality, based on 1-bar measurements on pseudo-single crystals. Alkali-feldspars present a large experimental challenge associated with their structural complexity. In the K-end member (KAlSi3O8) the symmetry is governed by Al/Si ordering, in the Na-end member (NaAlSi3O8) the symmetry is governed by whether or not there is a displacive collapse of the framework independent of the Al/Si ordering. K-feldspars exhibit monoclinic (C2/m) symmetry (necessitating determination of 13 elastic moduli) if disordered and triclinic (C-1) symmetry (21 elastic moduli) if ordered. Exsolution of Na-rich and K-rich phases is ubiquitous in natural samples, making it difficult to find suitable single phase and untwinned samples for study. The small single domain samples selected for this study were previously characterized by x-ray diffraction and microprobe analysis to ensure adequate sample quality. Surface wave velocities were measured on oriented surfaces of natural and synthetic single crystals using impulsively stimulated light scattering. A surface corrugation with a spacing of about 2 microns was impulsively created by the overlap of 100 ps infrared light pulses. The time evolution of the stimulated standing elastic waves was detected by measuring the intensity of diffraction from the surface corrugation of a variably delayed probe pulse. This method allows accurate (better than 0.2%) determination of velocities on samples smaller than 100 microns. The combination of measured surface wave velocities and

  7. Properties of alkali metal atoms deposited on a MgO surface: a systematic experimental and theoretical study.

    PubMed

    Finazzi, Emanuele; Di Valentin, Cristiana; Pacchioni, Gianfranco; Chiesa, Mario; Giamello, Elio; Gao, Hongjun; Lian, Jichun; Risse, Thomas; Freund, Hans-Joachim

    2008-01-01

    The adsorption of small amounts of alkali metal atoms (Li, Na, K, Rb, and Cs) on the surface of MgO powders and thin films has been studied by means of EPR spectroscopy and DFT calculations. From a comparison of the measured and computed g values and hyperfine coupling constants (hfccs), a tentative assignment of the preferred adsorption sites is proposed. All atoms bind preferentially to surface oxide anions, but the location of these anions differs as a function of the deposition temperature and alkali metal. Lithium forms relatively strong bonds with MgO and can be stabilized at low temperatures on terrace sites. Potassium interacts very weakly with MgO and is stabilized only at specific sites, such as at reverse corners where it can interact simultaneously with three surface oxygen atoms (rubidium and cesium presumably behave in the same way). Sodium forms bonds of intermediate strength and could, in principle, populate more than a single site when deposited at room temperature. In all cases, large deviations of the hfccs from the gas-phase values are observed. These reductions in the hfccs are due to polarization effects and are not connected to ionization of the alkali metal, which would lead to the formation of an adsorbed cation and a trapped electron. In this respect, hydrogen atoms behave completely differently. Under similar conditions, they form (H(+))(e(-)) pairs. The reasons for this different behavior are discussed. PMID:18381711

  8. CATION TRANSPORT AND PARTITIONING DURING A FIELD TEST OF ELECTROOSMOSIS

    EPA Science Inventory

    Field experiments were conducted to evaluate the effects of soil properties, such as the cation exchange capacity and mineral content, on pH, soluble ion concentrations, and electrical conductivity during electroosmosis in a silty clay soil. The soil is composed mainly of quartz ...

  9. Solvent-averaged potentials for alkali-, earth alkali-, and alkylammonium halide aqueous solutions

    NASA Astrophysics Data System (ADS)

    Hess, Berk; van der Vegt, Nico F. A.

    2007-12-01

    We derive effective, solvent-free ion-ion potentials for alkali-, earth alkali-, and alkylammonium halide aqueous solutions. The implicit solvent potentials are parametrized to reproduce experimental osmotic coefficients. The modeling approach minimizes the amount of input required from atomistic (force field) models, which usually predict large variations in the effective ion-ion potentials at short distances. For the smaller ion species, the reported potentials are composed of a Coulomb and a Weeks-Chandler-Andersen term. For larger ions, we find that an additional, attractive potential is required at the contact minimum, which is related to solvent degrees of freedom that are usually not accounted for in standard electrostatics models. The reported potentials provide a simple and accurate force field for use in molecular dynamics and Monte Carlo simulations of (poly-)electrolyte systems.

  10. High pressure Raman and single crystal X-ray diffraction of the alkali/calcium carbonate, shortite

    NASA Astrophysics Data System (ADS)

    Williams, Q. C.; Vennari, C.; O'Bannon, E. F., III

    2015-12-01

    Raman and synchrotron-based single crystal x-ray diffraction data have been collected on shortite (Na2Ca2(CO3)3) up to 10 GPa at 300 K. Shortite is of geological importance due to its presence in the ground-mass of kimberlites, and the alkaline-/carbon-rich character of kimberlitic eruptions. This investigation focuses on shortite's high pressure behavior and is relevant to the behavior of alkali-carbonate systems within Earth's upper mantle. X-ray data demonstrate that shortite's symmetry remains stable at high pressures—retaining orthorhombic C crystal system (Amm2) up to 10 GPa; diffraction data show a 12% volume decrease from room pressure, and a bulk modulus of 71.0(3) GPa. These also demonstrate that the c-axis is twice as compressible as the a- and b-axes. This anisotropic compression is likely due to the orientation of the relatively stiff carbonate groups, a third of which are oriented close to the plane of the a- and b-axes, c axis compression primarily involves the compaction of the 9-fold coordinate sodium and calcium polyhedral. The two distinct carbonate sites within the unit cell give rise to two Raman symmetric stretching modes of the symmetric stretch; the carbonate group stretching vibration which is close to in plane with the a- and b-axes shifts at 3.75 cm-1/GPa as opposed to the carbonate groups which is closer to in plane with the b- and c-axes which shift at 4.25 cm-1/GPa. This furthers evidence for anisotropic compression observed using x-ray diffraction--as the carbonate in plane with the a- and b-axes is compressed, the strength of oxygen bonds along the c-axis with the cations increases, thus decreasing the pressure shift of the mode. The out of plane bending vibration shifts at -0.48 cm-1/GPa, indicating an enhanced interaction of the oxygens with the cations. The multiple in plane bending modes all shift positively, as do at the low frequency lattice modes, indicating that major changes in bonding do not occur up to 10 GPa. The data

  11. Volcanic Origin of Alkali Halides on Io

    NASA Technical Reports Server (NTRS)

    Schaefer, L.; Fegley, B., Jr.

    2003-01-01

    The recent observation of NaCl (gas) on Io confirms our earlier prediction that NaCl is produced volcanically. Here we extend our calculations by modeling thermochemical equilibrium of O, S, Li, Na, K, Rb, Cs, F, Cl, Br, and I as a function of temperature and pressure in a Pele-like volcanic gas with O/S/Na/Cl/K = 1.518/1/0.05/0.04/0.005 and CI chondritic ratios of the other (as yet unobserved) alkalis and halogens. For reference, the nominal temperature and pressure for Pele is 1760 plus or minus 210 K and 0.01 bars based on Galileo data and modeling.

  12. Alkali differentiation in LL-chondrites

    NASA Astrophysics Data System (ADS)

    Wlotzka, F.; Palme, H.; Spettel, B.; Wanke, H.; Fredriksson, K.; Noonan, A. F.

    1983-04-01

    The Kraehenberg and Bhola LL-group chondrites are heterogeneous agglomerates which contain a variety of lithic fragments and chondrules as well as crystal fragments. Both meteorites contain large, cm-sized fragments with high K enrichments. The K-rich inclusions are fragments of larger rock bodies which crystallized from melts of chondritic parent material that had previously been enriched in K and in heavier alkalies,while also being depleted in Na and metal. It is suggested that the K enrichment occurred as an exchange for Na in feldspars via a vapor phase, whose presence on the chondrite parent body (or bodies) is supported by the recent finding of fluid inclusions in chondritic silicates. Cooling rate considerations indicate that the K-rich rock units could not have been very large, implying that the K-rich materials were locally molten by, for example, impact.

  13. Heat pipes containing alkali metal working fluid

    NASA Technical Reports Server (NTRS)

    Morris, J. F. (Inventor)

    1981-01-01

    A technique for improving high temperature evaporation-condensation heat-transfer devices which have important and unique advantage in terrestrial and space energy processing is described. The device is in the form of a heat pipe comprising a sealed container or envelope which contains a capillary wick. The temperature of one end of the heat pipe is raised by the input of heat from an external heat source which is extremely hot and corrosive. A working fluid of a corrosive alkali metal, such as lithium, sodium, or potassium transfers this heat to a heat receiver remote from the heat source. The container and wick are fabricated from a superalloy containing a small percentage of a corrosion inhibiting or gettering element. Lanthanum, scandium, yttrium, thorium, and hafnium are utilized as the alloying metal.

  14. Comparative alkali washing of simulated radioactive sludge

    SciTech Connect

    Fugate, G.A.; Ensor, D.D.; Egan, B.Z.

    1996-10-01

    The treatment of large volumes of radioactive sludge generated from uranium and plutonium recovery processes is a pressing problem in the environmental restoration currently planned at various U.S. Department of Energy sites. This sludge, commonly stored in underground tanks, is mainly in the form of metal oxides or precipitated metal hydroxides and the bulk of this material is nonradioactive. One method being developed to pretreat this waste takes advantage of the amphoteric character of aluminum and other nonradioactive elements. Previous studies have reported on the dissolution of eleven elements from simulated sludge using NaOH solutions up to 6M. This work provides a comparative study using KOH. The effectiveness of the alkali washing as a treatment method to reduce the bulk of radioactive sludge requiring long term isolation will be discussed.

  15. Solid state cell with alkali metal halo-alkali thiocyanate electrolyte

    SciTech Connect

    Rao, B. M.; Silbernagel, B. G.

    1980-02-26

    A novel electrochemical cell is disclosed utilizing: (A) an anode which contains an alkali metal as an anode-active material; (B) a cathode and (C) an electrolyte comprising an electrolytically effective amount of one or more compounds having the formula: (Ax)ma'scn wherein a is an alkali metal, X is a halogen, a' is an alkali metal and 0.1 < or = N < or = 10. Preferred systems include lithium-containing anodes, lithium-containing electrolytes and cathodes which contain cathode-active material selected from the group consisting of cathode-active sulfurs, halogens, halides, chromates, phosphates, oxides and chalcogenides, especially those chalcogenides of the empirical formula mzm wherein M is one or more metals selected from the group consisting of iron, titanium, zirconium, hafnium, niobium, tantalum and vanadium, Z is one or more chalcogens selected from the group consisting of oxygen, sulfur, selenium and tellurium, and M is a numerical value between about 1.8 and about 3.2.

  16. Ionic alkali halide XUV laser feasibility study

    SciTech Connect

    Yang, T.T.; Gylys, V.T.; Bower, R.D.; Harris, D.G.; Blauer, J.A.; Turner, C.E.; Hindy, R.N.

    1989-11-10

    The objective of this work is to assess the feasibility of a select set of ionic alkali halide XUV laser concepts by obtaining the relevant kinetic and spectroscopic parameters required for a proof-of-principle and conceptual design. The proposed lasers operate in the 80--200 nm spectral region and do not require input from outside radiation sources for their operation. Frequency up-conversion and frequency mixing techniques and therefore not considered in the work to be described. An experimental and theoretical study of a new type of laser operating in the extreme ultraviolet wavelength region has been conducted. The lasing species are singly ionized alkali halide molecules such as Rb{sup 2+}F{sub {minus}}, Rb{sup 2+}Br{sup {minus}} and Cs{sup 2+}F{sup {minus}}. These species are similar in electronic structure to the rare gas halide excimers, such as XeF and Krf, except that the ionic molecules emit at wavelengths of 80--200 nm, much shorter than the conventional rare-gas halide excimer laser. The radiative lifetime of these molecules are typically near 1 ns, which is about an order of magnitude shorter than that for rare-gas halide systems. The values of the cross section for stimulated emission are on the order of 1 {times} 10{sup {minus}16}cm{sup 2}. Because of the fundamental similarity to existing UV lasers, these systems show promise as a high power, efficient XUV lasers. 55 refs., 50 figs., 5 tabs.

  17. Cation-cation interactions and cation exchange in a series of isostructural framework uranyl tungstates

    NASA Astrophysics Data System (ADS)

    Balboni, Enrica; Burns, Peter C.

    2014-05-01

    The isotypical compounds (UO2)3(WO6)(H2O)5 (1), Ag(UO2)3(WO6)(OH)(H2O)3 (2), K(UO2)3(WO6)OH(H2O)4 (3), Rb(UO2)3(WO6)(OH)(H2O)3.5 (4), and Cs(UO2)3(WO6)OH(H2O)3 (5) were synthesized, characterized, and their structures determined. Each crystallizes in space group Cc. (1): a=12.979 (3), b=10.238 (2), c=11.302 (2), β=102.044 (2); (2): a=13.148 (2), b=9.520 (1), c=11.083 (2), β=101.568 (2); (3): a=13.111 (8), b=9.930 (6), c=11.242 (7), β=101.024 (7); (4): a=12.940 (2), b=10.231 (2), c=11.259(2), β=102.205 (2); (5): a=12.983 (3), b=10.191 (3), c=11.263 (4), β=101.661 (4). Compounds 1-5 are a framework of uranyl and tungsten polyhedra containing cation-cation interactions. The framework has three symmetrically distinct U(VI) cations, one tungsten, sixteen to eighteen oxygen atoms, and in 2-5, one monovalent cation. Each atom occupies a general position. Each U(VI) cation is present as a typical (UO2)2+ uranyl ion in an overall pentagonal bipyramidal coordination environment. Each pentagonal bipyramid shares two equatorial edges with two other pentagonal bipyramids, forming a trimer. Trimers are connected into chains by edge-sharing with WO6 octahedra. Chains are linked through cation-cation interactions between two symmetrically independent uranyl ions. This yields a remarkably complex system of intersecting channels that extend along [0 0 1] and [-1 1 0]. The cation exchange properties of 2 and 3 were characterized at room temperature and at 140 °C.

  18. Controlled in-situ dissolution of an alkali metal

    DOEpatents

    Jones, Jeffrey Donald; Dooley, Kirk John; Tolman, David Donald

    2012-09-11

    A method for the controllable dissolution of one or more alkali metals from a vessel containing a one or more alkali metals and/or one or more partially passivated alkali metals. The vessel preferably comprising a sodium, NaK or other alkali metal-cooled nuclear reactor that has been used. The alkali metal, preferably sodium, potassium or a combination thereof, in the vessel is exposed to a treatment liquid, preferably an acidic liquid, more preferably citric acid. Preferably, the treatment liquid is maintained in continuous motion relative to any surface of unreacted alkali metal with which the treatment liquid is in contact. The treatment liquid is preferably pumped into the vessel containing the one or more alkali metals and the resulting fluid is extracted and optionally further processed. Preferably, the resulting off-gases are processed by an off-gas treatment system and the resulting liquids are processed by a liquid disposal system. In one preferred embodiment, an inert gas is pumped into the vessel along with the treatment liquid.

  19. Ultrasonic coal washing to leach alkali elements from coals.

    PubMed

    Balakrishnan, S; Reddy, V Midhun; Nagarajan, R

    2015-11-01

    Deposition of fly ash particles onto heat-transfer surfaces is often one of the reasons for unscheduled shut-downs of coal-fired boilers. Fouling deposits encountered in convective sections of a boiler are characterized by arrival of ash particles in solidified (solid) state. Fouling is most frequently caused by condensation and chemical reaction of alkali vapors with the deposited ash particles creating a wet surface conducive to collect impacting ash particles. Hence, the amount of alkali elements present in coals, which, in turn, is available in the flue gas as condensable vapors, determines the formation and growth of fouling deposits. In this context, removal of alkali elements becomes vital when inferior coals having high-ash content are utilized for power generation. With the concept of reducing alkali elements present in a coal entering the combustor, whereby the fouling deposits can either be minimized or be weakened due to absence of alkali gluing effect, the ultrasonic leaching of alkali elements from coals is investigated in this study. Ultrasonic water-washing and chemical-washing, in comparison with agitation, are studied in order to estimate the intensification of the alkali removal process by sonication. PMID:26186840

  20. Alkali elemental and potassium isotopic compositions of Semarkona chondrules

    USGS Publications Warehouse

    Alexander, C.M. O'D.; Grossman, J.N.

    2005-01-01

    We report measurements of K isotope ratios in 28 Semarkona chondrules with a wide range of petrologic types and bulk compositions as well as the compositions of CPX-mesostasis pairs in 17 type I Semarkona chondrules, including two chondrules with radial alkali zonation and 19 type II chondrules. Despite the wide range in K/Al ratios, no systematic variations in K isotopic compositions were found. Semarkona chondrules do not record a simple history of Rayleigh-type loss of K. Experimentally determined evaporation rates suggest that considerable alkali evaporation would have occurred during chondrule formation. Nevertheless, based on Na CPX-mesostasis distribution coefficients, the alkali contents of the cores of most chondrules in Semarkona were probably established at the time of final crystallization. However, Na CPX-mesostasis distribution coefficients also show that alkali zonation in type I Semarkona chondrules was produced by entry of alkalis after solidification, probably during parent body alteration. This alkali metasomatism may have gone to completion in some chondrules. Our preferred explanation for the lack of systematic isotopic enrichments, even in alkali depleted type I chondrule cores, is that they exchanged with the ambient gas as they cooled. ?? The Meteoritical Society, 2005.

  1. Large electropositive cations as surfactants for the growth of polar epitaxial films

    NASA Astrophysics Data System (ADS)

    Cheung, Alfred K. C.; Elfimov, Ilya; Berciu, Mona; Sawatzky, George A.

    2015-03-01

    Using density functional theory (DFT) we demonstrate that the adsorption of large cations such as potassium or cesium facilitates the epitaxial growth of polar LaAlO3(LAO ) on SrTiO3(STO ). The low ionization potential of K favors efficient electron transfer to the STO conduction band and results in a two-dimensional electron gas which exactly compensates for the diverging potential with increasing layer thickness. For large cations like K or Cs, DFT total energy considerations show that they remain adsorbed on the LAO surface and do not enter substitutionally into LAO. These results suggest a scheme for growing clean LAO/STO interface systems, and polar systems in general, by performing the growth process in the presence of large, low ionization potential alkali-metal ions.

  2. Structural and Crystal Chemical Properties of Alkali Rare-earth Double Phosphates

    DOE PAGESBeta

    Farmer, James Matthew; Boatner, Lynn A.; Chakoumakos, Bryan C.; Rawn, Claudia J.; Richardson, Jim

    2016-01-01

    When appropriately activated, alkali rare-earth double phosphates of the form: M3RE(PO4)2 (where M denotes an alkali metal and RE represents either a rare-earth element or Y or Sc) are of interest for use as inorganic scintillators for radiation detection at relatively long optical emission wavelengths. These compounds exhibit layered crystal structures whose symmetry properties depend on the relative sizes of the rare-earth and alkali-metal cations. Single-crystal X-ray and powder neutron diffraction methods were used here to refine the structures of the series of rare-earth double phosphate compounds: K3RE(PO4)2 with RE = Lu, Er, Ho, Dy, Gd, Nd, Ce, plus Ymore » and Sc - as well as the compounds: A3Lu(PO4)2, with A = Rb, and Cs. The double phosphate K3Lu(PO4)2 was reported and structurally refined previously. This material had a hexagonal unit cell at room temperature with the Lu ion six-fold coordinated with oxygen atoms of the surrounding phosphate groups. Additionally two lower-temperature phases were observed for K3Lu(PO4)2. The first phase transition to a monoclinic P21/m phase occurred at ~230 K, and the Lu ion retained its six-fold coordination. The second K3Lu(PO4)2 phase transition occurred at ~130 K. The P21/m space group symmetry was retained, however, one of the phosphate groups rotated to increase the oxygen coordination number of Lu from six to seven. This structure then became isostructural with the room-temperature form of the compound K3Yb(PO4)2 reported here that also exhibits an additional high-temperature phase which occurs at T = 120 °C with a transformation to hexagonal P-3 space group symmetry and a Yb-ion coordination number reduction from seven to six. This latter result was confirmed using EXAFS. The single-crystal growth methods structural systematics, and thermal expansion properties of the present series of alkali rare-earth double phosphates, as determined by X-ray and neutron diffraction methods, are treated here.« less

  3. Structural and Crystal Chemical Properties of Alkali Rare-earth Double Phosphates

    SciTech Connect

    Farmer, James Matthew; Boatner, Lynn A.; Chakoumakos, Bryan C.; Rawn, Claudia J.; Richardson, Jim

    2016-01-01

    When appropriately activated, alkali rare-earth double phosphates of the form: M3RE(PO4)2 (where M denotes an alkali metal and RE represents either a rare-earth element or Y or Sc) are of interest for use as inorganic scintillators for radiation detection at relatively long optical emission wavelengths. These compounds exhibit layered crystal structures whose symmetry properties depend on the relative sizes of the rare-earth and alkali-metal cations. Single-crystal X-ray and powder neutron diffraction methods were used here to refine the structures of the series of rare-earth double phosphate compounds: K3RE(PO4)2 with RE = Lu, Er, Ho, Dy, Gd, Nd, Ce, plus Y and Sc - as well as the compounds: A3Lu(PO4)2, with A = Rb, and Cs. The double phosphate K3Lu(PO4)2 was reported and structurally refined previously. This material had a hexagonal unit cell at room temperature with the Lu ion six-fold coordinated with oxygen atoms of the surrounding phosphate groups. Additionally two lower-temperature phases were observed for K3Lu(PO4)2. The first phase transition to a monoclinic P21/m phase occurred at ~230 K, and the Lu ion retained its six-fold coordination. The second K3Lu(PO4)2 phase transition occurred at ~130 K. The P21/m space group symmetry was retained, however, one of the phosphate groups rotated to increase the oxygen coordination number of Lu from six to seven. This structure then became isostructural with the room-temperature form of the compound K3Yb(PO4)2 reported here that also exhibits an additional high-temperature phase which occurs at T = 120 °C with a transformation to hexagonal P-3 space group symmetry and a Yb-ion coordination number reduction from seven to six. This latter result was confirmed using EXAFS. The single

  4. Flexible polyelectrolyte conformation in the presence of cationic and anionic surfactants

    NASA Astrophysics Data System (ADS)

    Passos, C. B.; Kuhn, P. S.; Diehl, A.

    2015-11-01

    In this work we have studied the conformation of flexible polyelectrolyte chains in the presence of cationic and anionic surfactant molecules. We developed a simple theoretical model for the formation of the polyelectrolyte-cationic surfactant complexes and mixed micelles formed by cationic and anionic surfactant molecules, in the framework of the Debye-Hückel-Bjerrum-Manning and Flory theories, with the hydrophobic interaction included explicitly as an effective short-ranged attraction between the surfactant hydrocarbon tails. This simple model allows us to calculate the extension of the polyelectrolyte-cationic surfactant complexes as a function of the anionic surfactant concentration, for different types of cationic and anionic surfactant molecules. A discrete conformational transition from a collapsed state to an elongated coil was found, for all surfactant chain lengths we have considered, in agreement with the experimental observations for the unfolding of ​DNA-cationic surfactant complexes.

  5. Diverse, Alkali-Rich Igneous and Volcaniclastic Rocks Reflect a Metasomatised Mantle Beneath Gale Crater

    NASA Astrophysics Data System (ADS)

    Schmidt, M. E.; Baker, M. B.; Berger, J. A.; Fisk, M. R.; Gellert, R.; McLennan, S. M.; Newcombe, M. E.; Stolper, E. M.; Thompson, L. M.

    2014-12-01

    Although Curiosity landed in a sedimentary setting, geochemical compositions determined by Alpha Particle X-ray Spectrometer (APXS) and ChemCam suggest that major element concentrations of some rocks were little modified by chemical weathering, and in these cases, the bulk (>70%) of the crystalline components determined by ChemMin are igneous. Gale rocks can therefore largely preserve the composition of their igneous protoliths and provide insight into the crystalline basement exposed in the north crater rim. Four end-member compositions are recognized on the basis of APXS analyses. (1) The diverse, evolved Jake M class (n=12) of inferred igneous origin includes float blocks and cobbles. Jake M rocks are phonotephritic/mugearitic to trachyandesitic and characterized by low MgO contents (3.0-5.7 wt%) and high Al and alkalis, particularly Na2O (up to 7.35 wt%). (2) The Bathurst class of siltstones to coarse sandstones (n=13) occurs as dark-toned float and bedded outcrop and is basaltic to trachybasaltic, ranging to high K2O (up to 3.8 wt%). Alteration of the protolith(s) or during diagenesis may have affected this class. (3) The Darwin class of conglomerates to coarse sandstones (n=10) has high Na and Al, likely reflecting a sodic plagioclase-rich mineralogy, but with higher Fe than Jake M class (13.0-17.1 vs. 6.0-12.5 wt%). (4) The low alkali "normal" Mars basaltic composition is typified by the Portage soils (n=6) and the John Klein class (n=13; includes the Sheepbed mudstone). Some degree of mixing and/or contamination with this low alkali basaltic compositon has affected all APXS analyses. Overall, Gale rocks are strongly enriched in total alkalis (at the same MgO) relative to basaltic shergottites and many have higher K2O than igneous rocks analyzed by Spirit and Opportunity, suggesting that the mantle beneath Gale is alkali-rich (likely as a result of a metasomatic event) and that alkalis are heterogeneously distributed in the planet's interior.

  6. Increasing Class C fly ash reduces alkali silica reactivity

    SciTech Connect

    Hicks, J.K.

    2007-07-01

    Contrary to earlier studies, it has been found that incremental additions of Class C fly ash do reduce alkali silica reactivity (ASR), in highly reactive, high alkali concrete mixes. AST can be further reduced by substituting 5% metakaolin or silica fume for the aggregate in concrete mixes with high (more than 30%) Class C fly ash substitution. The paper reports results of studies using Class C fly ash from the Labadie Station plant in Missouri which typically has between 1.3 and 1.45% available alkalis by ASTM C311. 7 figs.

  7. Structure-properties relations of aluminum trichloride- alkali thiocyanate ionic complex liquids

    NASA Astrophysics Data System (ADS)

    Liu, Changle

    1997-10-01

    In the pseudo binary systems, AlCl3-MSCN (where M = Li, Na, or K), low-melting solutions that are ionically- conducting and glass-forming occur over a wide composition range. The phase equilibria features are very similar to those of the analogous AlCl3-MCl binaries except for significantly lower liquidus temperatures, especially in more acidic compositions. The high conductivities of these liquids, which makes them of interest for rechargeable alkali battery systems, are attributed to a high degree of decoupling of cations from the complex anion matrix. A thorough Raman and FTIR characterization was made of the liquid structure. It appears that the anion complexes that make up the structure of AlCl3-MSCN liquids are formed by Lewis acid-base reactions very similar to those of the AlCl3-MCl binaries. Thus, in equimolar and acidic melts, the species Al(SCN)Cl3/sp- and Al2(SCN)Cl6/sp- are predominant. In contrast to the simpler AlCl3-MCl binaries, however, SCN-Cl ligand exchange reactions can also occur, forming complex anions with more than one SCN group. The low melting points, high cation conductivities, and the relative ease of supercooling and glass formation in the AlCl3- MSCN systems are believed to be related to the presence of these large and asymmetric complex anions.

  8. Demixing and effective volatility of molten alkali carbonate melts in MCFCs

    SciTech Connect

    Brenscheidt, T.; Wendt, H.

    1996-12-31

    Since the early investigation of A. Klemm, the demixing of the cations of molten binary salt mixtures with a common anion due to the different mobilities of two different cations had been investigated in numerous experiments and the respective results interpreted in terms of structural features of the melts. 1-1 electrolytes had been preferentially investigated. Okada also reported investigations on lithium carbonate/potassium carbonate mixtures in the temperature range from 980 to 1070 K. From this investigation it is known that the heavier potassium cation is faster than lithium in mixtures which are more concentrated in potassium than x{sub K2CO3} = 0,32 (Chemla effect) whereas below this isotachic concentration lithium is faster. This paper investigates demixing in molten carbonate fuel cells.

  9. Divalent cation affinity sites in Paramecium aurelia.

    PubMed

    Fisher, G; Kaneshiro, E S; Peters, P D

    1976-05-01

    Sites with high calcium affinity in Paramecium aurelia were identified by high calcium (5 mM) fixation and electron microscope methods. Electron-opaque deposits were observed on the cytoplasmic side of surface membranes, particularly at the basal regions of cilia and trichocyst-pellicle fusion sites. Deposits were also observed on some smooth cytomembranes, within the axoneme of cilia, and on basal bodies. The divalent cations, Mg2+, Mn2+, Sr2+, Ni2+, Ba2+, and Zn2+, could be substituted for Ca2+ in the procedure. Deposits were larger with 5 mM Sr2+. Ba2+, and Mn2+ at ciliary transverse plates and the terminal plate of basal bodies. Microprobe analysis showed that Ca and C1 were concentrated within deposits. In some analyses, S and P were detected in deposits. Also, microprobe analysis of 5 mM Mn2+-fixed P. aurelia showed that those deposits were enriched in Mn and C1 and sometimes enriched in P. Deposits were seen only when the ciliates were actively swimming at the time of fixation. Locomotory mutants having defective membrane Ca-gating mechanisms and ciliates fixed while exhibiting ciliary reversal showed no obvious differences in deposition pattern and intensity. Possible correlations between electron-opaque deposits and the locations of intramembranous particles seen by freeze-fracture studied, as well as sites where fibrillar material associate with membranes are considered. The possibility that the action sites of calcium and other divalent cations were identified is discussed. PMID:1262398

  10. Titanium, vanadium, and niobium mineralization and alkali metasomatism from the Magnet Cove complex, Arkansas

    USGS Publications Warehouse

    Flohr, M.J.K.

    1994-01-01

    The Christy deposit formed through a series of complex processes. The initial phase of mineralization is directly related to the infiltration of novaculite by alkali-rich fluids that were probably derived from carbonatite magma. Titanium, V, Nb, and Li were introduced by the alkali-rich fluids at temperatures that were as high as 600??C. During the initial stage of mineralization, V was concentrated in aegirine and sodic amphibole, Li was concentrated in taeniolite, minor amounts of Ti were concentrated in aegirine, and pyrite formed. The replacement of novaculite by the aforementioned minerals yielded excess silica, which precipitated as quartz. Niobium- and V-bearing brookite precipitated with the quartz. Minerals formed during the first stage reacted with a second fluid at temperatures of 100?? to 300??C and V was then concentrated in smectite and goethite. The second fluid was a mixture of low-temperature metasomatic fluid and groundwater. Vanadium was further concentrated in clay minerals in goethite, and in vug minerals as low-temperature alteration proceeded. -from Author

  11. Diverse functions and molecular properties emerging for CAX Cation/H+ exchangers in plants

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Steep concentration gradients of many ions are actively maintained, with lower concentrations typically located in the cytosol, and higher concentrations in organelles and outside the cell. The vacuole is an important storage organelle for many ions. The concentration gradient of cations is establis...

  12. Effects of alkali treatment on the mechanical and thermal properties of Sansevieria trifasciata fiber

    NASA Astrophysics Data System (ADS)

    Mardiyati, Steven, Rizkiansyah, Raden Reza; Senoaji, A.; Suratman, R.

    2016-04-01

    In this study, Sansevieria trifasciata fibers were treated by NaOH with concentration 1%,3%, and 5wt% at 100°C for 2 hours. Chesson-Datta methods was used to determine the lignocellulose content of raw sansevieria fibers and to investigate effect of alkali treatment on lignin content of the fiber. Mechanical properties and thermal properties of treated and untreated fibers were measured by means of tensile testing machine and thermogravimetric analysis (TGA).The cellulose and lignin contents of raw sansevieria fiber obtained from Chesson-Datta method were 56% and 6% respectively. Mechanical testing of fibers showed the increase of tensile strength from 647 MPa for raw fibers to 902 MPa for 5wt% NaOH treated fibers. TGA result showed the alkali treatment increase the thermal resistance of fibers from 288°C for raw fibers to 307°C for 5% NaOH treated fiber. It was found that alkali treatment affect the mechanical properties and thermal properties of sansevieria fibers.

  13. Inhibitory effect of polysulfated heparin endostatin on alkali burn induced corneal neovascularization in rabbits

    PubMed Central

    Li, Zhao-Na; Yuan, Zhong-Fang; Mu, Guo-Ying; Hu, Ming; Cao, Li-Jun; Zhang, Ya-Li; Liu, Lei; Ge, Ming-Xu

    2015-01-01

    AIM To investigate anti-angiogenic effects of polysulfated heparin endostatin (PSH-ES) on alkali burn induced corneal neovascularization (NV) in rabbits. METHODS An alkali burn was made on rabbit corneas to induce corneal NV in the right eye of 24 rabbits. One day after burn creation, a 0.2 mL subconjunctival injection of 50 µg/mL PSH-ES, 50 µg/mL recombinant endostatin (ES), or normal saline was administered every other day for a total of 14d (7 injections). Histology and immunohistochemisty were used to examine corneas. Corneal NV growth was evaluated as microvessel quantity and corneal vascular endothelial growth factor (VEGF) expression was measured by immunohistochemical assay. RESULTS Subconjunctival injection of ES and PSH-ES resulted in significant corneal NV suppression, but PSH-ES had a more powerful anti-angiogenic effect than ES. Mean VEGF concentration in PSH-ES treated corneas was significantly lower than in ES treated and saline treated corneas. Histological examination showed that corneas treated with either PSH-ES or ES had significantly fewer microvessels than eyes treated with saline. Additionally corneas treated with PSH-ES had significantly fewer microvessels than corneas treated with ES. CONCLUSION Both PSH-ES and recombinant ES effectively inhibit corneal NV induced by alkali burn. However, PSH-ES is a more powerful anti-angiogenic agent than ES. This research has the potential to provide a new treatment option for preventing and treating corneal NV. PMID:25938033

  14. Halogenated silanes, radicals, and cations

    NASA Astrophysics Data System (ADS)

    Wang, Liming; He, Yi-Liang

    2008-09-01

    Quantum chemistry study has been carried out on the structure and energetics of halogenated silanes, radicals, and cations (SiHxXy0,+1, X = F, Cl, Br; x + y = 1-4). The geometries are optimized at B3LYP/6-31+G(2df,p) level. The adiabatic ionization energiess (IEas), relative energetics of cations, proton affinities (PAs) of silanes, and the enthalpies of formation are predicted using G3(CC) model chemistry. Non-classical ion complex structures are found for hydrogenated cations and transition states connecting classical and non-classical structures are also located. The most stable cations for silylene and silyl radicals have their classical divalent and trivalent structures, and those for silanes have non-classical structures except for SiH3Br+ and SiH2Br2+. The non-classical structures for halosilane cations imply difficulty in experimentally measurement of the adiabatic ionization energies using photoionization or photoelectron studies. For SiH3X, SiH2X2, and SiHX3, the G3(CC) adiabatic IEas to classical ionic structures closest to their neutrals agree better with the photoelectron spectroscopic measurements. The transition states between classical and non-classical structures also hamper the photoionization determination of the appearance energies for silylene cations from silanes. The G3(CC) results for SiHx0,+1 agree excellently with the photoionization mass spectrometric study, and the results for fluorinated and chlorinated species also agree with the previous theoretical predictions at correlation levels from BAC-MP4 to CCSD(T)/CBS. The predicted enthalpy differences between SiH2Cl+, SiHCl2+, and SiCl3+ are also in accordance with previous kinetics study. The G3(CC) results show large discrepancies to the collision-induced charge transfer and/or dissociation reactions involving SiFx+ and SiClx+ ions, for which the G3(CC) enthalpies of formation are also significantly differed from the previous theoretical predictions, especially on SiFx+ (x = 2-4). The G3

  15. Ethanol fermentation of cassava starch pretreated with alkali

    SciTech Connect

    Shin, Y.C.; Lee, S.Y.; Choe, Y.K.; Kim, H.S.; Byun, S.M.

    1986-04-01

    In view of the current industrial process for the conventional ethanol fermentation, in which raw starch materials are heated at 120 degrees C for 2 h, conditions for an alternative process were set: an overall time from saccharification to ethanol fermentation of within 3-4 days, an operation temperature of below 60 degrees C, an ethanol yield of over 93%, and a ratio of raw material to fermentation volume of within 1:4. To meet these conditions, previously a steeping method of starch materials in 0.5N HCl solution at 60 degrees C for 12 h were used, followed by combined actions of ..cap alpha..-amylase and glucoamylase. The ethanol yield from uncooked cassava starch treated under the conditions described was 95% after fermentation for 3 days with Saccharomyces cerevisiae. However, the use of a relatively higher concentration of acid for steeping is still a problem and gelatinization of starch materials is insufficient. This communication, therefore, describes effects of alkali steeping and structural change of starch granules on the ethanol fermentation. 8 references.

  16. Adsorptive bubble separation of zinc and cadmium cations in presence of ferric and aluminum hydroxides.

    PubMed

    Jurkiewicz, Kazimierz

    2005-06-15

    The adsorptive bubble separation of zinc and cadmium cations from solution in the presence of ferric and aluminum hydroxides was carried out by means of Tween 80 (nonionic surfactant), and sodium laurate and stearate (anionic surfactants). The mechanism of metal removal is different depending on the nature of the surfactant used. The removal of zinc cations by adsorbing colloid flotation is higher than that of cadmium cations. It increases with increases in the amount of hydroxide precipitate and the concentration of Tween 80. The removal of zinc cations by ion flotation is lower than that of cadmium cations. It does not change with increases in the hydroxide amount. It increases, however, with increased sodium laurate or stearate concentration. Both separation methods turned out to be helpful for studying both the solution's structure and the interactions at the solution-solid interface. PMID:15897071

  17. AMPHOTERIC COLLOIDS : I. CHEMICAL INFLUENCE OF THE HYDROGEN ION CONCENTRATION.

    PubMed

    Loeb, J

    1918-09-20

    1. It has been shown in this paper that while non-ionized gelatin may exist in gelatin solutions on both sides of the isoelectric point (which lies for gelatin at a hydrogen ion concentration of C(H) = 2.10(-5) or pH = 4.7), gelatin, when it ionizes, can only exist as an anion on the less acid side of its isoelectric point (pH > 4.7), as a cation only on the more acid side of its isoelectric point (pH < 4.7). At the isoelectric point gelatin can dissociate practically neither as anion nor as cation. 2. When gelatin has been transformed into sodium gelatinate by treating it for some time with M/32 NaOH, and when it is subsequently treated with HCl, the gelatin shows on the more acid side of the isoelectric point effects of the acid treatment only; while the effects of the alkali treatment disappear completely, showing that the negative gelatin ions formed by the previous treatment with alkali can no longer exist in a solution with a pH < 4.7. When gelatin is first treated with acid and afterwards with alkali on the alkaline side of the isoelectric point only the effects of the alkali treatment are noticeable. 3. On the acid side of the isoelectric point amphoteric electrolytes can only combine with the anions of neutral salts, on the less acid side of their isoelectric point only with cations; and at the isoelectric point neither with the anion nor cation of a neutral salt. This harmonizes with the statement made in the first paragraph, and the experimental results on the effect of neutral salts on gelatin published in the writer's previous papers. 4. The reason for this influence of the hydrogen ion concentration on the stability of the two forms of ionization possible for an amphoteric electrolyte is at present unknown. We might think of the possibility of changes in the configuration or constitution of the gelatin molecule whereby ionized gelatin can exist only as an anion on the alkaline side and as a cation on the acid side of its isoelectric point. 5. The

  18. Electric field-induced softening of alkali silicate glasses

    NASA Astrophysics Data System (ADS)

    McLaren, C.; Heffner, W.; Tessarollo, R.; Raj, R.; Jain, H.

    2015-11-01

    Motivated by the advantages of two-electrode flash sintering over normal sintering, we have investigated the effect of an external electric field on the viscosity of glass. The results show remarkable electric field-induced softening (EFIS), as application of DC field significantly lowers the softening temperature of glass. To establish the origin of EFIS, the effect is compared for single vs. mixed-alkali silicate glasses with fixed mole percentage of the alkali ions such that the mobility of alkali ions is greatly reduced while the basic network structure does not change much. The sodium silicate and lithium-sodium mixed alkali silicate glasses were tested mechanically in situ under compression in external electric field ranging from 0 to 250 V/cm in specially designed equipment. A comparison of data for different compositions indicates a complex mechanical response, which is observed as field-induced viscous flow due to a combination of Joule heating, electrolysis and dielectric breakdown.

  19. The 4843 Alkali Metal Storage Facility Closure Plan

    SciTech Connect

    Not Available

    1991-06-01

    The 4843 AMSF has been used primarily to provide a centralized building to receive and store dangerous and mixed alkali metal waste, including sodium and lithium, which has been generated at the Fast Flux Test Facility and at various other Hanford Site operations that used alkali metals. Most of the dangerous and mixed alkali metal waste received consists of retired equipment from liquid sodium processes. The unit continues to store material. In general, only solid alkali metal waste that is water reactive is stored at the 4843 AMSF. The 4843 AMSF will be closed in a manner consistent with Ecology guidelines and regulations (WAC 173-303-610). The general closure procedure is detailed as follows.

  20. Hall Determination of Atomic Radii of Alkali Metals

    ERIC Educational Resources Information Center

    Houari, Ahmed

    2008-01-01

    I will propose here an alternative method for determining atomic radii of alkali metals based on the Hall measurements of their free electron densities and the knowledge of their crystal structure. (Contains 2 figures.)

  1. Method for intercalating alkali metal ions into carbon electrodes

    DOEpatents

    Doeff, M.M.; Ma, Y.; Visco, S.J.; DeJonghe, L.

    1995-08-22

    A low cost, relatively flexible, carbon electrode for use in a secondary battery is described. A method is provided for producing same, including intercalating alkali metal salts such as sodium and lithium into carbon.

  2. Method for intercalating alkali metal ions into carbon electrodes

    DOEpatents

    Doeff, Marca M.; Ma, Yanping; Visco, Steven J.; DeJonghe, Lutgard

    1995-01-01

    A low cost, relatively flexible, carbon electrode for use in a secondary battery is described. A method is provided for producing same, including intercalating alkali metal salts such as sodium and lithium into carbon.

  3. Electric field-induced softening of alkali silicate glasses

    SciTech Connect

    McLaren, C.; Heffner, W.; Jain, H.; Tessarollo, R.; Raj, R.

    2015-11-02

    Motivated by the advantages of two-electrode flash sintering over normal sintering, we have investigated the effect of an external electric field on the viscosity of glass. The results show remarkable electric field-induced softening (EFIS), as application of DC field significantly lowers the softening temperature of glass. To establish the origin of EFIS, the effect is compared for single vs. mixed-alkali silicate glasses with fixed mole percentage of the alkali ions such that the mobility of alkali ions is greatly reduced while the basic network structure does not change much. The sodium silicate and lithium-sodium mixed alkali silicate glasses were tested mechanically in situ under compression in external electric field ranging from 0 to 250 V/cm in specially designed equipment. A comparison of data for different compositions indicates a complex mechanical response, which is observed as field-induced viscous flow due to a combination of Joule heating, electrolysis and dielectric breakdown.

  4. Effect of cavitation on removal of alkali elements from coal

    NASA Astrophysics Data System (ADS)

    Srivalli, H.; Nirmal, L.; Nagarajan, R.

    2015-12-01

    The main impurities in coal are sulphur, ash and alkali. On combustion, the volatile forms of these impurities are either condensed on the boilers, or emitted in the form of potentially hazardous gases. The alkali elements present in coal help the fly ash particles adhere to boiler surfaces by providing a wet surface on which collection of these particles can take place. Use of ultrasonic techniques in cleaning of coal has stirred interest among researchers in recent times. Extraction of alkali elements by cavitation effect using low-frequency ultrasound, in the presence of reagents (HNO3 and H2O2) is reported in this paper. Powdered coal was dissolved with the reagent and exposed to ultrasonic fields of various frequencies at different time intervals. The treated solution is filtered and tested for alkali levels.

  5. Cationic electrodepositable coating composition comprising lignin

    DOEpatents

    Fenn, David; Bowman, Mark P; Zawacky, Steven R; Van Buskirk, Ellor J; Kamarchik, Peter

    2013-07-30

    A cationic electrodepositable coating composition is disclosed. The present invention in directed to a cationic electrodepositable coating composition comprising a lignin-containing cationic salt resin, that comprises (A) the reaction product of: lignin, an amine, and a carbonyl compound; (B) the reaction product of lignin, epichlorohydrin, and an amine; or (C) combinations thereof.

  6. Preparation of poly(glycidylmethacrylate-divinylbenzene) weak acid cation exchange stationary phases with succinic anhydride, phthalic anhydride, and maleic anhydride for ion chromatography.

    PubMed

    Liu, Junwei; Wang, Yong; Wu, Shuchao; Zhang, Peimin; Zhu, Yan

    2016-08-01

    In this work, poly(glycidylmethacrylate-divinylbenzene) microspheres were prepared and applied for the preparation of weak acid cation exchange stationary phases. Succinic anhydride, phthalic anhydride, and maleic anhydride were selected as carboxylation reagents to prepare three weak acid cation exchangers by direct chemical derivatization reaction without solvent or catalyst. The diameters and dispersity of the microspheres were characterized by scanning electron microscopy; the amount of accessible epoxy groups and mechanical stability were also measured. The weak acid cation exchangers were characterized by Fourier transform infrared spectroscopy; the content of carboxyl groups was measured by traditional acid base titration method. The chromatographic properties were characterized and compared by separating alkali, alkaline earth metal ions and ammonium and polar amines. The separation properties enhanced in the order of succinic anhydride, phthalic anhydride, and maleic anhydride modified poly(glycidylmethacrylate-divinylbenzene) cation exchangers. PMID:27288092

  7. Rock Degradation by Alkali Metals: A Possible Lunar Erosion Mechanism.

    PubMed

    Naughton, J J; Barnes, I L; Hammond, D A

    1965-08-01

    When rocks melt under ultrahigh-vacuum conditions, their alkali components volatilize as metals. These metal vapors act to comminute polycrystalline rocks to their component minerals. The resultant powder is porous and loosely packed and its characteristics may be compatible with the lunar surface as revealed by the Ranger photographs. If meteorite impact or lunar volcanism has produced vaporization or areas of molten lava, alkali erosion may have given dust of this character in adjacent solid areas. PMID:17747570

  8. Electrochemical cell having an alkali-metal-nitrate electrode

    DOEpatents

    Roche, M.F.; Preto, S.K.

    1982-06-04

    A power-producing secondary electrochemical cell includes a molten alkali metal as the negative-electrode material and a molten-nitrate salt as the positive-electrode material. The molten material in the respective electrodes are separated by a solid barrier of alkali-metal-ion conducting material. A typical cell includes active materials of molten sodium separated from molten sodium nitrate and other nitrates in mixture by a layer of sodium ..beta..'' alumina.

  9. Organochlorine compounds in Purple Heron eggs (Ardea purpurea) nesting in sites located around a chlor-alkali plant (Ebro River).

    PubMed

    Huertas, David; Grimalt, Joan O; Jover, Lluís; Sanpera, Carola; Ruiz, Xavier

    2016-01-01

    Eggs of Purple Heron (Ardea purpurea) were collected from three sampled sites inside the Ebro River basin in years 2006 and 2007. These sites were located besides (Flix), upstream (Aiguabarreig) and downstream (Delta) a chlor-alkali plant. Organochlorine compounds (OCs) such as dichlorodiphenyltrichloroethanes (DDTs), polychlorobiphenyls (PCBs), polychlorostyrenes (PCSs), hexachlorobenzene (HCB), pentachlorobenzene (PeCB) and hexachlorocyclohexanes (HCHs) were analysed to assess what are the accumulation patterns of these compounds in aquatic migratory birds breeding in the area of influence of the emissions from this industrial installation. Comparison of the egg concentrations between the three sites show higher concentrations of compounds manufactured in the past in the factory (PCBs, p,p'-DDT) or by-products of OC synthesis (HCB, PeCB and PCSs) in Flix than in Aiguabarreig reflecting a clear influence from the emissions of the chlor-alkali plant. The eggs collected in the Ebro Delta showed higher concentrations of total DDTs (mainly p,p'-DDE) than in the reference site (Aiguabarreig) which could reflect past applications of this insecticide in the area for agriculture. In contrast, HCHs were found in higher concentrations in the Delta and Aiguabarreig than in the Flix Reservoir. These compounds have been used as insecticides in agriculture and were not manufactured in the chlor-alkali plant. The present results show that despite Purple Herons are migratory birds, the food web transfer of OCs during the breeding season is sufficient for the accumulation of these compounds in the eggs, leading to statistically significant concentration differences between sites. These differences are consistent with the emissions of these pollutants from industrial or agricultural sources to the aquatic environments. Some of the p,p'-DDE concentrations observed in the area nearby the chlor-alkali plant are above the threshold effects for reproductive impairment. PMID:26202210

  10. Gaseous protein cations are amphoteric

    SciTech Connect

    Stephenson, J.L. Jr.; McLuckey, S.A.

    1997-02-19

    Singly- and multiply-protonated ubiquitin molecules are found to react with iodide anions, and certain other anions, by attachment of the anion, in competition with proton transfer to the anion. The resulting adduct ions are relatively weakly bound and dissociate upon collisional activation by loss of the neutral acid derived from the anion. Adduct ions that behave similarly can also be formed via ion/molecule reactions involving the neutral acid. The ion/molecule reaction phenomenology, however, stands in contrast with that expected based on the reaction site(s) being charged. Reaction rates increase inversely with charge state and the total number of neutral molecules that add to the protein cations increases inversely with cation charge. These observations are inconsistent with the formation of proton-bound clusters but are fully consistent with the formation of ion pairs or dipole/dipole bonding involving the neutral acid and neutral basic sites in the protein. The ion/ion reactions can be interpreted on the basis of conjugate acid/base chemistry in which the anion, which is a strong gaseous base, reacts with a protonated site, which is a strong gaseous acid. Adduct ions can also be formed via ion/molecule reaction which, on the basis of microscopic reversibility, implies that the neutral acid interacts with neutral basic sites on the protein cation. 26 refs., 10 figs., 1 tab.

  11. Alkali metal yttrium neo-pentoxide double alkoxide precursors to alkali metal yttrium oxide nanomaterials

    DOE PAGESBeta

    Boyle, Timothy J.; Neville, Michael L.; Sears, Jeremiah Matthew; Cramer, Roger

    2016-03-15

    In this study, a series of alkali metal yttrium neo-pentoxide ([AY(ONep)4]) compounds were developed as precursors to alkali yttrium oxide (AYO2) nanomaterials. The reaction of yttrium amide ([Y(NR2)3] where R=Si(CH3)3) with four equivalents of H-ONep followed by addition of [A(NR2)] (A=Li, Na, K) or Ao (Ao=Rb, Cs) led to the formation of a complex series of AnY(ONep)3+n species, crystallographically identified as [Y2Li3(μ3-ONep)(μ3-HONep)(μ-ONep)5(ONep)3(HONep)2] (1), [YNa2(μ3-ONep)4(ONep)]2 (2), {[Y2K3(μ3-ONep)3(μ-ONep)4(ONep)2(ηξ-tol)2][Y4K2(μ4-O)(μ3-ONep)8(ONep)4]•ηx-tol]} (3), [Y4K2(μ4-O)(μ3-ONep)8(ONep)4] (3a), [Y2Rb3(μ4-ONep)3(μ-ONep)6] (4), and [Y2Cs4(μ6-O)(μ3-ONep)6(μ3-HONep)2(ONep)2(ηx-tol)4]•tol (5). Compounds 1–5 were investigated as single source precursors to AYOx nanomaterials following solvothermal routes (pyridine, 185 °C for 24h). The final products after thermal processing weremore » found by powder X-ray diffraction experiments to be Y2O3 with variable sized particles based on transmission electron diffraction. Energy dispersive X-ray spectroscopy studies indicated that the heavier alkali metal species were present in the isolated nanomaterials.« less

  12. Alkali-slag cements for the immobilization of radioactive wastes

    SciTech Connect

    Shi, C.; Day, R.L.

    1996-12-31

    Alkali-slag cements consist of glassy slag and an alkaline activator and can show both higher early and later strengths than Type III Portland cement, if a proper alkaline activator is used. An examination of microstructure of hardened alkali-slag cement pastes with the help of XRD and SEM with EDAX shows that the main hydration product is C-S-H (B) with low C/S ratio and no crystalline substances exist such as Ca(OH){sub 2}, Al (OH){sub 3} and sulphoaluminates. Mercury intrusion tests indicate that hardened alkali-slag cement pastes have a lower porosity than ordinary Portland cement, and contain mainly gel pores. The fine pore structure of hardened alkali-slag cement pastes will restrict the ingress of deleterious substances and the leaching of harmful species such as radionuclides. The leachability of Cs{sup + } from hardened alkali-slag cement pastes is only half of that from hardened Portland cement. From all these aspects, it is concluded that alkali-slag cements are a better solidification matrix than Portland cement for radioactive wastes.

  13. Temperature dependence of elastic properties in alkali borate binary glasses

    NASA Astrophysics Data System (ADS)

    Kawashima, Mitsuru; Matsuda, Yu; Kojima, Seiji

    2011-05-01

    The elastic properties of alkali borate glasses, xM 2O·(100 - x)B 2O 3 (M = Li, Na, K, Rb, Cs, x = 14, 28), have been investigated by Brillouin scattering spectroscopy from room temperature up to 1100 °C. Above the glass transition temperature, Tg, the longitudinal sound velocity, VL, decreases markedly on heating. Such significant changes of the elastic properties result from the breakdown of the glass network above Tg. Alkali borate family with the same x shows the similar behavior in the temperature variations of VL up to around Tg. The absorption coefficient, αL, increases gradually above Tg. With the increase of the size of an alkali ion, the slope of VL just above Tg decreases. Since the fragility is related to the slope, the present results suggest that the fragility of alkali borate glasses increases as the size of alkali ion decreases. Such an alkali dependence of the fragility is discussed on the basis of the fluctuation of the boron coordination number.

  14. Two-phase alkali-metal experiments in reduced gravity

    SciTech Connect

    Antoniak, Z.I.

    1986-06-01

    Future space missions envision the use of large nuclear reactors utilizing either a single or a two-phase alkali-metal working fluid. The design and analysis of such reactors require state-of-the-art computer codes that can properly treat alkali-metal flow and heat transfer in a reduced-gravity environment. A literature search of relevant experiments in reduced gravity is reported on here, and reveals a paucity of data for such correlations. The few ongoing experiments in reduced gravity are noted. General plans are put forth for the reduced-gravity experiments which will have to be performed, at NASA facilities, with benign fluids. A similar situation exists regarding two-phase alkali-metal flow and heat transfer, even in normal gravity. Existing data are conflicting and indequate for the task of modeling a space reactor using a two-phase alkali-metal coolant. The major features of past experiments are described here. Data from the reduced-gravity experiments with innocuous fluids are to be combined with normal gravity data from the two-phase alkali-metal experiments. Analyses undertaken here give every expectation that the correlations developed from this data base will provide a valid representation of alkali-metal heat transfer and pressure drop in reduced gravity.

  15. Reduction of phosphorus and alkali levels in coking coals

    SciTech Connect

    Hoare, I.C.; Waugh, A.B.

    1995-12-31

    A number of coals, though exhibiting desirable coking properties, can have undesirable levels of alkalis and phosphorus. All the phosphorus in the coal will report to the coke, eventually to the iron and thence to the steel, with adverse effects on its metallurgical properties. Alkalis have damaging effects on the blast furnace operation and can be responsible for loss of heat, loss of production, efficiency loss and reduced furnace life. Buyers of coking coal commonly specify such parameters as phosphorus in coal and alkalis in ash, with penalties and rejection over certain limits. With the introduction of new direct reduction technologies such as COREX and HISMELT, and others such as PCI, it is anticipated that coal producers will have even tighter phosphorus and alkali specifications imposed on their products. Phosphorus is predominantly inorganic in origin occurring in a wide variety of minerals in coal, but its main source is apatite. It can be found mainly in the lower density fractions of the coal and intimately bound, so that conventional physical beneficiation techniques are relatively ineffective. CSIRO has developed a cost effective, selective chemical demineralization treatment, which can be applied to the problem of high alkali, high phosphorus coals. This particular technique makes use of unrefined organic acid, which also has the advantage of being low in cost and environmentally benign. In this paper, the effectiveness of acid demineralization of a number of coals is discussed, within the context of their phosphorus and alkali distributions throughout various size/density fractions.

  16. Small diatomic alkali molecules at ultracold temperatures

    NASA Astrophysics Data System (ADS)

    Wang, Tout Taotao

    This thesis describes experimental work done with two of the smallest diatomic alkali molecules, 6Li2 and 23Na 6Li, each formed out of its constituent atoms at ultracold temperatures. The 23Na6Li molecule was formed for the first time at ultracold temperatures, after previous attempts failed due to an incorrect assignment of Feshbach resonances in the 6Li+23Na system. The experiment represents successful molecule formation around the most difficult Feshbach resonance ever used, and opens up the possibility of transferring NaLi to its spin-triplet ground state, which has both magnetic and electric dipole moments and is expected to be long-lived. For 6Li2, the experimental efforts in this thesis have solved a long-standing puzzle of apparently long lifetimes of closed-channel fermion pairs around a narrow Feshbach resonance, finding that the lifetime is in fact short, as expected in the absence of Pauli suppression of collisions. Moreover, measurements of collisions of Li2 with free Li atoms demonstrates a striking first example of collisions involving molecules at ultracold temperatures described by physics beyond universal long-range van der Waals interactions.

  17. Superconductivity in alkali-doped fullerene nanowhiskers.

    PubMed

    Takeya, Hiroyuki; Konno, Toshio; Hirata, Chika; Wakahara, Takatsugu; Miyazawa, Kun'ichi; Yamaguchi, Takahide; Tanaka, Masashi; Takano, Yoshihiko

    2016-09-01

    Superconductivity in alkali metal-doped fullerene nanowhiskers (C60NWs) was observed in K3.3C60NWs, Rb3.0C60NWs and Cs2.0Rb1.0C60NWs with transition temperatures at 17, 25 and 26 K, respectively. Almost full shielding volume fraction (~80%) was observed in K3.3C60NWs when subjected to thermal treatment at 200 °C for a duration of 24 h. In contrast, the shielding fraction of Rb3.0C60NWs and Cs2.0Rb1.0C60NWs were calculated to be 8% and 6%, respectively. Here we report on an extensive investigation of the superconducting properties of these AC60NWs (A  =  K3.3, Rb3.0 and Cs2.0Rb1.0). These properties are compared to the ones reported on the corresponding conventional (single-crystal or powder) K-doped fullerene. We also evaluated the critical current densities of these C60NWs using the Bean model under an applied magnetic field up to 50 kOe. PMID:27385220

  18. Bioinorganic Chemistry of the Alkali Metal Ions.

    PubMed

    Kim, Youngsam; Nguyen, Thuy-Tien T; Churchill, David G

    2016-01-01

    The common Group 1 alkali metals are indeed ubiquitous on earth, in the oceans and in biological systems. In this introductory chapter, concepts involving aqueous chemistry and aspects of general coordination chemistry and oxygen atom donor chemistry are introduced. Also, there are nuclear isotopes of importance. A general discussion of Group 1 begins from the prevalence of the ions, and from a comparison of their ionic radii and ionization energies. While oxygen and water molecule binding have the most relevance to biology and in forming a detailed understanding between the elements, there is a wide range of basic chemistry that is potentially important, especially with respect to biological chelation and synthetic multi-dentate ligand design. The elements are widely distributed in life forms, in the terrestrial environment and in the oceans. The details about the workings in animal, as well as plant life are presented in this volume. Important biometallic aspects of human health and medicine are introduced as well. Seeing as the elements are widely present in biology, various particular endogenous molecules and enzymatic systems can be studied. Sodium and potassium are by far the most important and central elements for consideration. Aspects of lithium, rubidium, cesium and francium chemistry are also included; they help in making important comparisons related to the coordination chemistry of Na(+) and K(+). Physical methods are also introduced. PMID:26860297

  19. Superconductivity in alkali-doped fullerene nanowhiskers

    NASA Astrophysics Data System (ADS)

    Takeya, Hiroyuki; Konno, Toshio; Hirata, Chika; Wakahara, Takatsugu; Miyazawa, Kun’ichi; Yamaguchi, Takahide; Tanaka, Masashi; Takano, Yoshihiko

    2016-09-01

    Superconductivity in alkali metal-doped fullerene nanowhiskers (C60NWs) was observed in K3.3C60NWs, Rb3.0C60NWs and Cs2.0Rb1.0C60NWs with transition temperatures at 17, 25 and 26 K, respectively. Almost full shielding volume fraction (~80%) was observed in K3.3C60NWs when subjected to thermal treatment at 200 °C for a duration of 24 h. In contrast, the shielding fraction of Rb3.0C60NWs and Cs2.0Rb1.0C60NWs were calculated to be 8% and 6%, respectively. Here we report on an extensive investigation of the superconducting properties of these AC60NWs (A  =  K3.3, Rb3.0 and Cs2.0Rb1.0). These properties are compared to the ones reported on the corresponding conventional (single-crystal or powder) K-doped fullerene. We also evaluated the critical current densities of these C60NWs using the Bean model under an applied magnetic field up to 50 kOe.

  20. Prediction of Intrinsic Cesium Desorption from Na-Smectite in Mixed Cation Solutions.

    PubMed

    Fukushi, Keisuke; Fukiage, Tomo

    2015-09-01

    Quantitative understanding of the stability of sorbed radionuclides in smectite is necessary to assess the performance of engineering barriers used for nuclear waste disposal. Our previous study demonstrated that the spatial organization of the smectite platelets triggered by the divalent cations led to the apparent fixation of intrinsic Cs in smectite, because some Cs is retained inside the formed tactoids. Natural water is usually a mixture of Na(+) and divalent cations (Ca(2+) and Mg(2+)). This study therefore investigated the desorption behavior of intrinsic Cs in Na-smecite in mixed Na(+)-divalent cation solutions under widely various cation concentrations using batch experiments, grain size measurements, and cation exchange modeling (CEM). Results show that increased Na(+) concentrations facilitate Cs desorption because Na(+) serves as the dispersion agent. A linear relation was obtained between the logarithm of the Na(+) fraction and the accessible Cs fraction in smectite. That relation enables the prediction of accessible Cs fraction as a function of solution cationic compositions. The corrected CEM considering the effects of the spatial organization suggests that the stability of intrinsic Cs in the smectite is governed by the Na(+) concentration, and suggests that it is almost independent of the concentrations of divalent cations in natural water. PMID:26206200

  1. Relation between the electroforming voltage in alkali halide-polymer diodes and the bandgap of the alkali halide

    SciTech Connect

    Bory, Benjamin F.; Wang, Jingxin; Janssen, René A. J.; Meskers, Stefan C. J.; Gomes, Henrique L.; De Leeuw, Dago M.

    2014-12-08

    Electroforming of indium-tin-oxide/alkali halide/poly(spirofluorene)/Ba/Al diodes has been investigated by bias dependent reflectivity measurements. The threshold voltages for electrocoloration and electroforming are independent of layer thickness and correlate with the bandgap of the alkali halide. We argue that the origin is voltage induced defect formation. Frenkel defect pairs are formed by electron–hole recombination in the alkali halide. This self-accelerating process mitigates injection barriers. The dynamic junction formation is compared to that of a light emitting electrochemical cell. A critical defect density for electroforming is 10{sup 25}/m{sup 3}. The electroformed alkali halide layer can be considered as a highly doped semiconductor with metallic transport characteristics.

  2. Fibrin solubilizing properties of certain anionic and cationic detergents.

    PubMed

    Chakrabarty, S

    1989-08-15

    The fibrinolytic (fibrin dissolving) properties of several anionic, cationic, nonionic and zwitterionic detergents were assessed in an in vitro fibrin agarose assay. Of the 4 anionic detergents tested, only sodium dodecyl sulfate (SDS) was found to be fibrinolytic. SDS was fibrinolytic either in the absence or presence of factor XIII. Four other cationic detergents were found to possess similar fibrinolytic properties. These cationic detergents were cetyltrimethylammonium bromide (CTAB), mix alkyltrimethyl ammonium bromide (MTAB), hexadecyltrimethylammonium bromide (HTAB) and cetylpyridium chloride (CPC). The nonionic (digitonin, triton X-100/tween 20) and zeitterionic (CHAPS, zeittergent 3-08) detergents were not fibrinolytic. Detergents mediated fibrinolysis, unlike that of tissue type plasminogen activator and urokinase, was independent of the presence of plasminogen. Non-detergents such as polyethylene glycol and highly charged compounds such as poly-1-lysine and poly-1-glutamic acid were not fibrinolytic. Fibrinolytic activity was observed for SDS and the cationic detergents at concentrations ranging from 0.1-10 percent. The effects of these fibrinolytic detergents (SDS, CTAB, MTAB, HTAB and CPC) on clot formation and on pre-formed clots were then assessed, using freshly drawn human venous blood. Incorporation of these detergents into blood inhibited the formation of clots in a concentration dependent manner. The detergents were also able to dissolve pre-formed clots in a similar fashion. SDS was found to be most potent in these properties. PMID:2510356

  3. Fly ash adsorbents for multi-cation wastewater treatment

    NASA Astrophysics Data System (ADS)

    Visa, Maria; Isac, Luminita; Duta, Anca

    2012-06-01

    Class "F" fly ash (FA), collected from the Central Heat and Power (CHP) Plant Brasov (Romania), with oxides composition SiO2/Al2O3 over 2.4 proved good adsorbent properties, and was further used for obtaining a new substrate with good adsorption capacity for heavy metals from multi-cation wastewater treatment. Firstly, the new adsorbent was characterized by AFM, XRD, DSC, FTIR and the surface energy was evaluated by contact angle measurements. The experimental data suggested that the new type of substrate is predominant crystalline with highly polar surface. The substrate was used for removing the Pb2+, Cd2+ and Zn2+ cations from mixed solutions. The results show high efficiency and selective adsorption the Pb2+ and Zn2+ cations. The optimized adsorption parameters were further used in thermodynamic and kinetic studies of the adsorption processes. The Langmuir and Freundlich models were used to describe the processes. The pseudo-second order kinetics could well model all the processes, indicating a surface concentration of the adsorption sites with the same order of magnitude as the cation concentrations.

  4. Hyperconjugation in diethyl ether cation versus diethyl sulfide cation.

    PubMed

    Morita, Masato; Matsuda, Yoshiyuki; Endo, Tomoya; Mikami, Naohiko; Fujii, Asuka; Takahashi, Kaito

    2015-09-28

    Ionization of a molecule can greatly alter its electronic structure as well as its geometric structure. In this collaborative experimental and theoretical study, we examined variance in hyperconjugation upon ionization of diethyl ether (DEE) and diethyl sulfide (DES). We obtained the experimental gas phase vibrational spectra of DEE, DES, DEE(+), DES(+), DEE(+)-Ar, and DES(+)-Ar in the wavenumber region of 2500 to 3600 cm(-1). For DEE(+) and DEE(+)-Ar, we observed a greatly red shifted CH stretching peak at 2700 cm(-1), while the lowest CH stretching peaks for DEE, DES, DES(+) and DES(+)-Ar were observed around 2850 cm(-1). For DEE(+), we calculated a drastic red shifted CH stretching peak at 2760 cm(-1), but for DEE, DES, and DES(+) the lowest CH stretching peaks were calculated to be at 2860, 2945, and 2908 cm(-1), respectively. In addition, for DEE, the minima (maxima) geometry in the neutral state becomes a maxima (minima) geometry in the cationic state, while similar minima geometries are seen in neutral and cationic states of DES. These experimental and theoretical findings were rationalized through the natural bond orbital analysis by quantifying the hyperconjugation between the σCH orbital and the ionized singly occupied p orbital of the oxygen (sulfur) in DEE(+) (DES(+)). This study showed how orientation with the ionized orbital can greatly affect the neighboring CH bond strength and its polarity, as well as the geometry of the system. Furthermore, this change in the CH bond strength between DEE(+) and DES(+) is quantified from the energies for intramolecular proton transfer in the two cations. PMID:26300267

  5. Binding of monovalent alkali metal ions with negatively charged phospholipid membranes.

    PubMed

    Maity, Pabitra; Saha, Baishakhi; Kumar, Gopinatha Suresh; Karmakar, Sanat

    2016-04-01

    We have systematically investigated the effect of various alkali metal ions with negatively charged phospholipid membranes. Size distributions of large unilamellar vesicles have been confirmed using dynamic light scattering. Zeta potential and effective charges per vesicle in the presence of various alkali metal ions have been estimated from the measured electrophoretic mobility. We have determined the intrinsic binding constant from the zeta potential using electrostatic double layer theory. The reasonable and consistent value of the intrinsic binding constant of Na(+), found at moderate NaCl concentration (10-100 mM), indicates that the Gouy-Chapman theory cannot be applied for very high (> 100mM) and very low (< 10 mM) electrolyte concentrations. The isothermal titration calorimetry study has revealed that the net binding heat of interaction of the negatively charged vesicles with monovalent alkali metal ions is small and comparable to those obtained from neutral phosphatidylcholine vesicles. The overall endothermic response of binding heat suggests that interaction is primarily entropy driven. The entropy gain might arise due to the release of water molecules from the hydration layer vicinity of the membranes. Therefore, the partition model which does not include the electrostatic contribution suffices to describe the interaction. The binding constant of Na(+) (2.4 ± 0.1 M(-1)), obtained from the ITC, is in agreement with that estimated from the zeta potential (-2.0 M(-1)) at moderate salt concentrations. Our results suggest that hydration dynamics may play a vital role in the membrane solution interface which strongly affects the ion-membrane interaction. PMID:26802251

  6. Alkali-aggregate reactivity of typical siliceious glass and carbonate rocks in alkali-activated fly ash based geopolymers

    NASA Astrophysics Data System (ADS)

    Lu, Duyou; Liu, Yongdao; Zheng, Yanzeng; Xu, Zhongzi; Shen, Xiaodong

    2013-08-01

    For exploring the behaviour of alkali-aggregate reactivity (AAR) in alkali-activated geopolymeric materials and assessing the procedures for testing AAR in geopolymers, the expansion behaviour of fly ash based geopolymer mortars with pure silica glass and typical carbonate rocks were studied respectively by curing at various conditions, i.e. 23°C and 38°C with relative humidity over 95%, immersed in 1M NaOH solution at 80°C. Results show that, at various curing conditions, neither harmful ASR nor harmful ACR was observed in geopolymers with the criteria specified for OPC system. However, with the change of curing conditions, the geopolymer binder and reactive aggregates may experience different reaction processes leading to quite different dimensional changes, especially with additional alkalis and elevated temperatures. It suggests that high temperature with additional alkali for accelerating AAR in traditional OPC system may not appropriate for assessing the alkali-aggregate reactivity behaviour in geopolymers designed for normal conditions. On the other hand, it is hopeful to control the dimensional change of geopolymer mortar or concrete by selecting the type of aggregates and the appropriate curing conditions, thus changing the harmful AAR in OPC into beneficial AAR in geopolymers and other alkali-activated cementitious systems.

  7. On-chip fabrication of alkali-metal vapor cells utilizing an alkali-metal source tablet

    NASA Astrophysics Data System (ADS)

    Tsujimoto, K.; Ban, K.; Hirai, Y.; Sugano, K.; Tsuchiya, T.; Mizutani, N.; Tabata, O.

    2013-11-01

    We describe a novel on-chip microfabrication technique for the alkali-metal vapor cell of an optically pumped atomic magnetometer (OPAM), utilizing an alkali-metal source tablet (AMST). The newly proposed AMST is a millimeter-sized piece of porous alumina whose considerable surface area holds deposited alkali-metal chloride (KCl) and barium azide (BaN6), source materials that effectively produce alkali-metal vapor at less than 400 °C. Our experiments indicated that the most effective pore size of the AMST is between 60 and 170 µm. The thickness of an insulating glass spacer holding the AMST was designed to confine generated alkali metal to the interior of the vapor cell during its production, and an integrated silicon heater was designed to seal the device using a glass frit, melted at an optimum temperature range of 460-490 °C that was determined by finite element method thermal simulation. The proposed design and AMST were used to successfully fabricate a K cell that was then operated as an OPAM with a measured sensitivity of 50 pT. These results demonstrate that the proposed concept for on-chip microfabrication of alkali-metal vapor cells may lead to effective replacement of conventional glassworking approaches.

  8. A molecular dynamic model for analyzing concentrations of electrolytes: Fractional molar dependences of microstructure properties

    NASA Astrophysics Data System (ADS)

    Khalansky, D.; Popova, E.; Gladyshev, P.; Dushanov, E.; Kholmurodov, Kh.

    2014-12-01

    Aqueous electrolyte solutions play an important role in many electrophysical and chemical processes in aerospace technology and industrial applications. As noncovalent interactions, the interactions between ions are crucially important for biomolecular structures as well (protein structure folding, molecular level processes followed by ionic pair correlations, the formation of flexible hydrate shells, and so on). Specifically, ions (cations and anions with the same valence charges) can form stable pairs if their sizes match. The formation of ionic pairs can substantially affect the thermodynamic stabilities of proteins in the alkali salts physiologically present in the human body. Research aims and problems impose severe demands on readjustments of the ionic force fields and potential parameters developed to describe aqueous solutions and electrolytic systems. Ionic solutions and their interaction with biomolecules have been observed for over 100 years [1], but the behavior of such solutions remains poorly studied today. New data obtained in this work deals with parameterization strategies and adjustments for the ionic force fields of the alkali cations and halide anions that should be helpful in biomolecular research. Using molecular dynamics (MD) models, four electrolytic systems (HCl-H2O, LiCl-H2O, NaCl-H2O, and KCl-H2O) are investigated as binary mixtures of water and cations and anions, respectively. The intermolecular interaction parameters are varied for two of the four model electrolytes (HCl-H2O and NaCl-H2O) to simulate the possibility of different ionic shells forming during interaction with water. It is found that varying the potential parameters strongly affects the dynamic and structural characteristics of electrolyte systems. MD simulations are performed in the temperature range of 300 to 600 K with a step of 50 K. MD simulations for all electrolyte models (HCl-H2O, LiCl-H2O, NaCl-H2O, KCl-H2O) are also conducted for different molar fractions of

  9. The reaction dynamics of alkali dimer molecules and electronically excited alkali atoms with simple molecules

    SciTech Connect

    Hou, H.

    1995-12-01

    This dissertation presents the results from the crossed molecular beam studies on the dynamics of bimolecular collisions in the gas phase. The primary subjects include the interactions of alkali dimer molecules with simple molecules, and the inelastic scattering of electronically excited alkali atoms with O2. The reaction of the sodium dimers with oxygen molecules is described in Chapter 2. Two reaction pathways were observed for this four-center molecule-molecule reaction, i.e. the formations of NaO2 + Na and NaO + NaO. NaO2 products exhibit a very anisotropic angular distribution, indicating a direct spectator stripping mechanism for this reaction channel. The NaO formation follows the bond breaking of O2, which is likely a result of a charge transfer from Na2 to the excited state orbital of O2-. The scattering of sodium dimers from ammonium and methanol produced novel molecules, NaNH3 and Na(CH3OH), respectively. These experimental observations, as well as the discussions on the reaction dynamics and the chemical bonding within these molecules, will be presented in Chapter 3. The lower limits for the bond dissociation energies of these molecules are also obtained. Finally, Chapter 4 describes the energy transfer between oxygen molecules and electronically excited sodium atoms.

  10. Influence of cations on noncovalent interactions between 6-propionyl-2-dimethylaminonaphthalene (PRODAN) and dissolved fulvic and humic acids.

    PubMed

    Gadad, Praveen; Nanny, Mark A

    2008-12-01

    The influence of cations (Na(+), Ca(2+) and Mg(2+)) on noncovalent interactions between 6-propionyl-2-dimethylaminonaphthalene (PRODAN) and dissolved fulvic acids (FAs) (Norman landfill leachate fulvic acid (NLFA) and Suwannee River fulvic acid (SRFA)) and dissolved humic acids (HAs) (Suwannee River humic acid (SRHA) and Leonardite humic acid (LHA)) was examined using steady-state fluorescence spectroscopy at pH 4, 7 and 10 as a function of cation concentration (up to 25-100mM). Regardless of pH and cation concentration, PRODAN quenching by FA was unaffected by cations. However, interactions between PRODAN and HA decreased in the presence of cations at pH 7 and 10. Cation concentrations below the HA charge density resulted in the greatest decrease of PRODAN quenching, while very little additional decrease in PRODAN quenching occurred at cation concentrations above the HA charge density. This suggests that as the HA carboxylic acid functional groups form inner sphere complexes with divalent cations, intramolecular interactions result in a contraction of the HA molecular structure, thereby preventing PRODAN from associating with the condensed aromatic, electron accepting moieties inherent within HA molecules and responsible for PRODAN quenching. However, once the HA carboxylic acid functional groups are fully titrated with divalent cations, PRODAN quenching is no longer significantly influenced by the further addition of cations, even though these additional cations facilitate intermolecular interactions between the HA molecules to form supramolecular HA aggregates that can continue to increase in size. Regardless of FA and HA type, pH, cation type and concentration, the lack of blue-shifted fluorescence emission spectra indicated that micelle-like hydrophobic regions, amenable to PRODAN partitioning, were not formed by intra- and intermolecular interactions of FA and HA. PMID:18849058

  11. General features in the stoichiometry and stability of ionophore A23187-cation complexes in homogeneous solution.

    PubMed

    Chapman, C J; Puri, A K; Taylor, R W; Pfeiffer, D R

    1990-08-15

    Existing literature describing the stoichiometry and stability of complexes between A23187 and divalent cations in solution has been extended to include additional transition series cations, the heavy-metal cations Cd2+ and Pb2+, plus seven lanthanide series trivalent cations. Stability constants of 1:1 complexes between the ionophore and the divalent cations vary by 6.2 orders of magnitude between Cu2+ and Ba2+ which are the strongest and weakest complexes, respectively. Considering alkaline-earth and first-series transition cations together, the pattern of stability constants obeys the extended Irving-Williams series as is seen with many nonionophorous liganding agents. Cd2+ and Pb2+ are bound with an affinity similar to those of Mn2+ and Zn2+, whereas the lanthanides are bound with little selectivity and slightly higher stability. Titration of the ionophore in the 10(-5) M concentration range with di- and trivalent cations gives rise first to complexes of stoichiometry MA2 and subsequently to MA as the metal concentration is increased. The second stepwise stability constants for formation of the MA2 species exceeds the first constant by approximately 10-fold. With lanthanides, heavy metals, and transition-metal cations, OH-, at near physiological concentrations, competes significantly with free ionophore for binding to the 1:1 complexes. This competition is not apparent when Ca2+ or Mg2+ are the central cations. Possible implications of the 1:1 complex selectivity pattern, the ionophore-hydroxide competitive binding equilibria, and potential ternary complexes involving 1:1 ionophore:cation complexes and other anions present in biological systems are discussed with respect to the ionophore's transport selectivity and biological actions. PMID:2116770

  12. Diffusion with chemical reaction: An attempt to explain number density anomalies in experiments involving alkali vapor

    NASA Technical Reports Server (NTRS)

    Snow, W. L.

    1974-01-01

    The mutual diffusion of two reacting gases is examined which takes place in a bath of inert gas atoms. Solutions are obtained between concentric spheres, each sphere acting as a source for one of the reactants. The calculational model is used to illustrate severe number density gradients observed in absorption experiments with alkali vapor. Severe gradients result when sq root k/D R is approximately 5 where k, D, and R are respectively the second order rate constant, the multicomponent diffusion constant, and the geometrical dimension of the experiment.

  13. Alkali-metal gases in optical lattices: Possible new type of quantum crystals

    NASA Astrophysics Data System (ADS)

    Meyerovich, A. E.

    2003-11-01

    Similarities between alkali-metal gases in optical lattices with noninteger occupation of the lattice sites and quantum crystals are explored. The analogy with the vacancy liquid (VL) provides an alternative explanation to the Mott transition for the recent experiment on the phase transition in the lattice. The VL can undergo Bose-Einstein condensation (BEC) with Tc within experimental reach. Direct and vacancy-assisted mechanisms of the band motion for hyperfine impurities are discussed. A large concentration of vacancies can result in the spatial decomposition of the system into pure hyperfine components. Below the vacancy condensation the impurity component resembles 3He in 3He He II mixtures.

  14. Theory of Magnetotransport Anomalies in Alkali Metals

    NASA Astrophysics Data System (ADS)

    Zhu, Xiaodong

    The galvanomagnetic properties of alkali metals, especially those of potassium, are studied taking into account the existence of an incommensurate change-density wave (CDW) structure. Occurrence of the CDW broken symmetry truncates the Fermi surface with a large number of energy gaps. Furthermore, any macroscopic crystal is likely divided into CDW (')Q-domains. An orientational (')Q-texture leads to a preferred direction in the crystal. For such an exotic system the effective magnetoresistivity tensor is anomalous and is derived for various magnetic fields. The residual (zero-field) resistance is also anisotropic. For fields 0.5 - 3T, Hall coefficients are found to be anisotropic, and a longitudinal-transverse mixing effect is discovered. The diagonal elements of the magnetoresistivity tensor are found to have a linear magnetoresistance. When the field is increased above 4T sharp open-orbit magnetoresistance spectrum develops. From the theoretical magnetoresistivity tensor, the induced-torque amplitude and phase patterns for potassium spheres are calculated. The theory quantitatively explains all of the induced-torque anomalies found experimentally in the last fourteen years. An interacting electron system, which is free of the CDW instabilities, is also studied by considering its spin response to a weak sinusoidal magnetic field. The many-body correction G(,-)((')q,(omega)) caused by exchange and correlation is introduced to describe the correct wave -vector- and frequency-dependent spin susceptibility. The exact behavior of G(,-)((')q,(omega)) in the large-q limit is shown to be related to the pair distribution function g((')r) at r = 0. G(,-)((')q,(omega)) (--->) 4g(0)-1 /3, as q (--->) (INFIN).At metallic densities this value is negative, opposite in sign to the limit at small wave vectors. Thus the spin susceptibility for large wave vectors is suppressed, rather than enhanced, by many-body effects.

  15. [Effect of univalent cations on synthesis of surfactants by Acinetobacter calcoaceticus IMV B-7241].

    PubMed

    Pirog, T P; Shevchuk, T A; Antoniuk, S I; Kravchenko, E Iu; Iutinskaia, G A

    2013-01-01

    The effect of univalent cations on activity of key enzymes of C2-metabolism has been investigated in the producer of biosurfactants, Acinetibacter calcoaceticus IMV B-7241 grown on ethanol. It was established that potassium cations are inhibitors of pyroquinolinequinone-dependent alcohol- and acetaldehyde dehydrogenases, the enzymes of biosynthesis of surface-active aminolipids (NADP-dependent glutamate dehydrogenase) and glycolipids (phosphoenopyruvate (PhEP)-carboxikinase), while ammonium cations are activators of these enzymes and PhEP-carboxylase. A decrease of potassium cations concentration in the cultivation medium to 1 mM and increase of the content of amine nitrogen to 10 mM as a result of potassium nitrate substitution by equimolar, as to nitrogen, urea concentration were accompanied by the increase of activity of enzymes of ethanol metabolism and SAS biosynthesis, as well as by the 2-fold increase of conditional concentration of the biosurfactants. PMID:23720959

  16. Raman Analysis of Perrhenate and Pertechnetate in Alkali Salts and Borosilicate Glasses

    SciTech Connect

    Gassman, Paul L.; McCloy, John S.; Soderquist, Chuck Z.; Schweiger, Michael J.

    2014-01-03

    Sodium borosilicate glasses containing various concentrations of rhenium or technetium were fabricated, and their vibrational spectra studied using a Raman microscope. Spectra were interpreted with reference to new high resolution measurements of alkali pertechnetates and perrhenates NaReO4, KReO4, NaTcO4, and KTcO4. At low concentrations of ReO4- or TcO4-, glass spectra show weak peaks superimposed on a dominant spectrum of glass characteristic of silicate and borate network vibrations. At high concentrations, sharp peaks characteristic of crystal field splitting and C4h symmetry dominate the spectra of glasses, indicating alkali nearby tetrahedral Re or Tc. Often peaks indicative of both the K and Na pertechnetates/ perrhenates are evident in the Raman spectrum, with the latter being favored at high additions of the source chemical, since Na is more prevalent in the glass and ion exchange takes place. These results have significance to immobilization of nuclear waste containing radioactive 99Tc in glass for ultimate disposal.

  17. Cation coordination in oxychloride glasses

    NASA Astrophysics Data System (ADS)

    Johnson, J. A.; Holland, D.; Bland, J.; Johnson, C. E.; Thomas, M. F.

    2003-02-01

    Glasses containing mixtures of cations and anions of nominal compositions [Sb2O3]x - [ZnCl2]1-x where x = 0.25, 0.50, 0.75, and 1.00, have been studied by means of neutron diffraction and Raman and Mössbauer spectroscopy. There is preferential bonding within the system with the absence of Sb-Cl bonds. Antimony is found to be threefold coordinated to oxygen, and zinc fourfold coordinated. The main contributing species are of the form [Sb(OSb)2(OZn)] and [Zn(ClZn)2(OSb)2].

  18. Isomer-specific analysis and toxic evaluation of polychlorinated naphthalenes in soil, sediment, and biota collected near the site of a former chlor-alkali plant

    SciTech Connect

    Kannan, K.; Blankenship, A.L.; Giesy, J.P.; Imagawa, T.

    1998-09-01

    Concentrations and composition of polychlorinated naphthalene (PCN) congeners were determined in soil, sediments, blue crab, striped mullet, and boat-tailed grackle collected near a chlor-alkali plant to determine their congener profile, bioaccumulation properties, and toxic potential. Concentrations of total PCNs as high as 23 {micro}g/g, dry wt, were found in sediments collected at the marsh contaminated by disposal of wastes from the chlor-alkali process. The spatial distribution of sediment-PCN concentrations was not related with those observed for polychlorinated biphenyls (PCBs). The PCN congener profile did not resemble those of any technical mixtures. Hepta- and octa-chloronaphthalenes were the most abundant congeners accounting for greater than 50% of the total PCN concentrations in soil and sediments. A characteristic profile of PCNs in samples collected at the chlor-alkali site suggests the formation of chloronaphthalene congeners during chlor-alkali process, as has been suggested for polychlorinated dibenzofurans (PCDFs). Concentrations of total PCNs in biota were 3--5 orders of magnitude less than in sediments. The profile of PCN congeners in biota was predominated by tetra- or penta-chloronaphthalenes, while hepta- and octa-chloronaphthalenes were not detected.

  19. A hydrophobic filter confers the cation selectivity of Zygosaccharomyces rouxii plasma-membrane Na+/H+ antiporter.

    PubMed

    Kinclova-Zimmermannova, Olga; Falson, Pierre; Cmunt, Denis; Sychrova, Hana

    2015-04-24

    Na(+)/H(+) antiporters may recognize all alkali-metal cations as substrates but may transport them selectively. Plasma-membrane Zygosaccharomyces rouxii Sod2-22 antiporter exports Na(+) and Li(+), but not K(+). The molecular basis of this selectivity is unknown. We combined protein structure modeling, site-directed mutagenesis, phenotype analysis and cation efflux measurements to localize and characterize the cation selectivity region. A three-dimensional model of the ZrSod2-22 transmembrane domain was generated based on the X-ray structure of the Escherichia coli NhaA antiporter and primary sequence alignments with homologous yeast antiporters. The model suggested a close proximity of Thr141, Ala179 and Val375 from transmembrane segments 4, 5 and 11, respectively, forming a hydrophobic hole in the putative cation pathway's core. A series of mutagenesis experiments verified the model and showed that structural modifications of the hole resulted in altered cation selectivity and transport activity. The triple ZrSod2-22 mutant T141S-A179T-V375I gained K(+) transport capacity. The point mutation A179T restricted the antiporter substrate specificity to Li(+) and reduced its transport activity, while serine at this position preserved the native cation selectivity. The negative effect of the A179T mutation can be eliminated by introducing a second mutation, T141S or T141A, in the preceding transmembrane domain. Our experimental results confirm that the three residues found through modeling play a central role in the determination of cation selectivity and transport activity in Z. rouxii Na(+)/H(+) antiporter and that the cation selectivity can be modulated by repositioning a single local methyl group. PMID:25701798

  20. The Production of Polycyclic Aromatic Hydrocarbon Anions in Inert Gas Matrices Doped with Alkali Metals. Electronic Absorption Spectra of the Pentacene Anion (C22H14(-))

    NASA Technical Reports Server (NTRS)

    Halasinski, Thomas M.; Hudgins, Douglas M.; Salama, Farid; Allamandola, Louis J.; Mead, Susan (Technical Monitor)

    1999-01-01

    The absorption spectra of pentacene (C22H14) and its radical cation (C22H14(+)) and anion (C22H14(-)) isolated in inert-gas matrices of Ne, Ar, and Kr are reported from the ultraviolet to the near-infrared. The associated vibronic band systems and their spectroscopic assignments are discussed together with the physical and chemical conditions governing ion (and counterion) production in the solid matrix. In particular, the formation of isolated pentacene anions is found to be optimized in matrices doped with alkali metal (Na and K).