Science.gov

Sample records for alkali chloride salts

  1. Production of chlorine from chloride salts

    DOEpatents

    Rohrmann, Charles A.

    1981-01-01

    A process for converting chloride salts and sulfuric acid to sulfate salts and elemental chlorine is disclosed. A chloride salt and sulfuric acid are combined in a furnace where they react to produce a sulfate salt and hydrogen chloride. Hydrogen chloride from the furnace contacts a molten salt mixture containing an oxygen compound of vanadium, an alkali metal sulfate and an alkali metal pyrosulfate to recover elemental chlorine. In the absence of an oxygen-bearing gas during the contacting, the vanadium is reduced, but is regenerated to its active higher valence state by separately contacting the molten salt mixture with an oxygen-bearing gas.

  2. Solution-Derived, Chloride-Containing Minerals as a Waste Form for Alkali Chlorides

    SciTech Connect

    Riley, Brian J.; Crum, Jarrod V.; Matyas, Josef; McCloy, John S.; Lepry, William C.

    2012-10-01

    Sodalite [Na8(AlSiO4)6Cl2] and cancrinite [(Na,K)6Ca2Al6Si6O24Cl4] are environmentally stable, chloride-containing minerals and are a logical waste form option for the mixed alkali chloride salt waste stream that is generated from a proposed electrochemical separations process during nuclear fuel reprocessing. Due to the volatility of chloride salts at moderate temperatures, the ideal processing route for these salts is a low-temperature approach such as the sol-gel process. The sodalite structure can be easily synthesized by the sol-gel process; however, it is produced in the form of a fine powder with particle sizes on the order of 1–10 µm. Due to the small particle size, these powders require additional treatment to form a monolith. In this study, the sol-gel powders were pressed into pellets and fired to achieve > 90% of theoretical density. The cancrinite structure, identified as the best candidate mineral form in terms of waste loading capacity, was only produced on a limited basis following the sol-gel process and converted to sodalite upon firing. Here we discuss the sol-gel process specifics, chemical durability of select waste forms, and the steps taken to maximize chloride-containing phases, decrease chloride loss during pellet firing, and increase pellet densities.

  3. 40 CFR 721.8900 - Substituted halogenated pyridinol, alkali salt.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ..., alkali salt. 721.8900 Section 721.8900 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.8900 Substituted halogenated pyridinol, alkali salt. (a) Chemical... as substituted halogenated pyridinols, alkali salts (PMNs P-88-1271 and P-88-1272) are subject...

  4. 40 CFR 721.5278 - Substituted naphthalenesulfonic acid, alkali salt.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., alkali salt. 721.5278 Section 721.5278 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.5278 Substituted naphthalenesulfonic acid, alkali salt. (a) Chemical... as a substituted naphthalenesulfonic acid, alkali salt (PMN P-95-85) is subject to reporting...

  5. 40 CFR 721.5278 - Substituted naphthalenesulfonic acid, alkali salt.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ..., alkali salt. 721.5278 Section 721.5278 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.5278 Substituted naphthalenesulfonic acid, alkali salt. (a) Chemical... as a substituted naphthalenesulfonic acid, alkali salt (PMN P-95-85) is subject to reporting...

  6. 40 CFR 721.8900 - Substituted halogenated pyridinol, alkali salt.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., alkali salt. 721.8900 Section 721.8900 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.8900 Substituted halogenated pyridinol, alkali salt. (a) Chemical... as substituted halogenated pyridinols, alkali salts (PMNs P-88-1271 and P-88-1272) are subject...

  7. 40 CFR 721.5278 - Substituted naphthalenesulfonic acid, alkali salt.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., alkali salt. 721.5278 Section 721.5278 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.5278 Substituted naphthalenesulfonic acid, alkali salt. (a) Chemical... as a substituted naphthalenesulfonic acid, alkali salt (PMN P-95-85) is subject to reporting...

  8. 40 CFR 721.5278 - Substituted naphthalenesulfonic acid, alkali salt.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., alkali salt. 721.5278 Section 721.5278 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.5278 Substituted naphthalenesulfonic acid, alkali salt. (a) Chemical... as a substituted naphthalenesulfonic acid, alkali salt (PMN P-95-85) is subject to reporting...

  9. 40 CFR 721.8900 - Substituted halogenated pyridinol, alkali salt.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., alkali salt. 721.8900 Section 721.8900 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.8900 Substituted halogenated pyridinol, alkali salt. (a) Chemical... as substituted halogenated pyridinols, alkali salts (PMNs P-88-1271 and P-88-1272) are subject...

  10. 40 CFR 721.8900 - Substituted halogenated pyridinol, alkali salt.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., alkali salt. 721.8900 Section 721.8900 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.8900 Substituted halogenated pyridinol, alkali salt. (a) Chemical... as substituted halogenated pyridinols, alkali salts (PMNs P-88-1271 and P-88-1272) are subject...

  11. 40 CFR 721.8900 - Substituted halogenated pyridinol, alkali salt.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ..., alkali salt. 721.8900 Section 721.8900 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.8900 Substituted halogenated pyridinol, alkali salt. (a) Chemical... as substituted halogenated pyridinols, alkali salts (PMNs P-88-1271 and P-88-1272) are subject...

  12. 40 CFR 721.5278 - Substituted naphthalenesulfonic acid, alkali salt.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ..., alkali salt. 721.5278 Section 721.5278 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.5278 Substituted naphthalenesulfonic acid, alkali salt. (a) Chemical... as a substituted naphthalenesulfonic acid, alkali salt (PMN P-95-85) is subject to reporting...

  13. 40 CFR 721.4660 - Alcohol, alkali metal salt.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Alcohol, alkali metal salt. 721.4660... Substances § 721.4660 Alcohol, alkali metal salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as alcohol, alkali metal salt (PMN P-91-151)...

  14. 40 CFR 721.4660 - Alcohol, alkali metal salt.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Alcohol, alkali metal salt. 721.4660... Substances § 721.4660 Alcohol, alkali metal salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as alcohol, alkali metal salt (PMN P-91-151)...

  15. 40 CFR 721.4660 - Alcohol, alkali metal salt.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Alcohol, alkali metal salt. 721.4660... Substances § 721.4660 Alcohol, alkali metal salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as alcohol, alkali metal salt (PMN P-91-151)...

  16. 40 CFR 721.4660 - Alcohol, alkali metal salt.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Alcohol, alkali metal salt. 721.4660... Substances § 721.4660 Alcohol, alkali metal salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as alcohol, alkali metal salt (PMN P-91-151)...

  17. 40 CFR 721.4660 - Alcohol, alkali metal salt.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Alcohol, alkali metal salt. 721.4660... Substances § 721.4660 Alcohol, alkali metal salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance generically identified as alcohol, alkali metal salt (PMN P-91-151)...

  18. Salts of alkali metal anions and process of preparing same

    DOEpatents

    Dye, James L.; Ceraso, Joseph M.; Tehan, Frederick J.; Lok, Mei Tak

    1978-01-01

    Compounds of alkali metal anion salts of alkali metal cations in bicyclic polyoxadiamines are disclosed. The salts are prepared by contacting an excess of alkali metal with an alkali metal dissolving solution consisting of a bicyclic polyoxadiamine in a suitable solvent, and recovered by precipitation. The salts have a gold-color crystalline appearance and are stable in a vacuum at -10.degree. C. and below.

  19. Development of an alkali chloride vapour-generating apparatus for calibration of ultraviolet absorption measurements

    NASA Astrophysics Data System (ADS)

    Leffler, T.; Brackmann, C.; Berg, M.; Aldén, M.; Li, Z. S.

    2017-02-01

    A novel design of alkali chloride vapour-generating cell has been developed, which can serve as a calibration cell for quantitative ultraviolet absorption concentration measurements and meticulous spectral investigations of alkali compounds. The calibration cell was designed to provide alkali vapour of well-controlled concentrations and temperatures, and consisted of a sealed quartz cell measuring 0.4 m in length with a temperature-controlled reservoir containing solid alkali salt. The cell was placed in a furnace and the alkali vapours generated from the reservoir have direct access to the measuring chamber. Investigations of potassium chloride (KCl) were made on sublimated vapour at temperatures 650, 700, 750, 780, and 800 °C while the reservoir temperature was kept 50 °C lower to avoid condensation. The cell provides stable KCl vapour pressures, and the furnace provides a homogenous temperature profile along the cell. KCl vapour pressures are well characterised and conform the base for determination of the KCl concentration in the cell. The alkali chloride levels matched the concentration range of the absorption setup and indicated a previously employed calibration method to overestimate KCl concentrations. The KCl absorption cross sections for wavelengths λ =197.6 nm and λ =246.2 nm were calculated to be 3.4 × 10-17 and 2.9 × 10-17 cm2/molecule, respectively. The absorption cross section spectra did not show any structural differences with increasing temperature, which could indicate influence of dimers or significant changes of the population in the KCl vibrational states. The KCl absorption cross sections thus did not show any temperature dependence in the temperature region of 700-800 °C. Moreover, the applicability of the calibration cell for measurement of other alkali chlorides and hydroxides is discussed.

  20. Alkali Metal/Salt Thermal-Energy-Storage Systems

    NASA Technical Reports Server (NTRS)

    Phillips, Wayne W.; Stearns, John W.

    1987-01-01

    Proposed thermal-energy-storage system based on mixture of alkali metal and one of its halide salts; metal and salt form slurry of two immiscible melts. Use of slurry expected to prevent incrustations of solidified salts on heat-transfer surfaces that occur where salts alone used. Since incrustations impede heat transfer, system performance improved. In system, charging heat-exchanger surface immersed in lower liquid, rich in halide-salt, phase-charge material. Discharging heat exchanger surface immersed in upper liquid, rich in alkali metal.

  1. Salt, Chlor-Alkali, and Related Heavy Chemicals

    NASA Astrophysics Data System (ADS)

    Bommaraju, Tilak V.

    The chemical category of inorganic salts encompasses many substances that dissociate completely in water, but only one salt, sodium chloride, is referred to by the common name, salt. Sodium chloride is ubiquitous in both its occurrence and its many uses. To date, there are over 14,000 uses for salt.1 Salt is used as a feedstock for many chemicals including chlorine, caustic soda (sodium hydroxide), synthetic soda ash (sodium carbonate), sodium chlorate, sodium sulfate, and metallic sodium. By indirect methods, sodium chloride is also used to produce hydrochloric acid and many other sodium salts. In its natural mineral form, salt may take on some color from some of the trace elements and other salts present, however, pure sodium chloride is a white to colorless crystalline substance, fairly soluble in water.2 Also known as halite, the substance is an essential nutrient to humans and animals for proper bodily functions.

  2. Sodium (Salt or Sodium Chloride)

    MedlinePlus

    ... foods available to you and millions of other consumers. You will have the power to choose the ... cutting back and how to build a healthier relationship with food. Sea Salt Versus Table Salt Discover ...

  3. Salt, chloride, bleach, and innate host defense

    PubMed Central

    Wang, Guoshun; Nauseef, William M.

    2015-01-01

    Salt provides 2 life-essential elements: sodium and chlorine. Chloride, the ionic form of chlorine, derived exclusively from dietary absorption and constituting the most abundant anion in the human body, plays critical roles in many vital physiologic functions, from fluid retention and secretion to osmotic maintenance and pH balance. However, an often overlooked role of chloride is its function in innate host defense against infection. Chloride serves as a substrate for the generation of the potent microbicide chlorine bleach by stimulated neutrophils and also contributes to regulation of ionic homeostasis for optimal antimicrobial activity within phagosomes. An inadequate supply of chloride to phagocytes and their phagosomes, such as in CF disease and other chloride channel disorders, severely compromises host defense against infection. We provide an overview of the roles that chloride plays in normal innate immunity, highlighting specific links between defective chloride channel function and failures in host defense. PMID:26048979

  4. Salt, chloride, bleach, and innate host defense.

    PubMed

    Wang, Guoshun; Nauseef, William M

    2015-08-01

    Salt provides 2 life-essential elements: sodium and chlorine. Chloride, the ionic form of chlorine, derived exclusively from dietary absorption and constituting the most abundant anion in the human body, plays critical roles in many vital physiologic functions, from fluid retention and secretion to osmotic maintenance and pH balance. However, an often overlooked role of chloride is its function in innate host defense against infection. Chloride serves as a substrate for the generation of the potent microbicide chlorine bleach by stimulated neutrophils and also contributes to regulation of ionic homeostasis for optimal antimicrobial activity within phagosomes. An inadequate supply of chloride to phagocytes and their phagosomes, such as in CF disease and other chloride channel disorders, severely compromises host defense against infection. We provide an overview of the roles that chloride plays in normal innate immunity, highlighting specific links between defective chloride channel function and failures in host defense.

  5. An electron diffraction study of alkali chloride vapors

    NASA Technical Reports Server (NTRS)

    Mawhorter, R. J.; Fink, M.; Hartley, J. G.

    1985-01-01

    A study of monomers and dimers of the four alkali chlorides NaCl, KCl, RbCl, and CsCl in the vapor phase using the counting method of high energy electron diffraction is reported. Nozzle temperatures from 850-960 K were required to achieve the necessary vapor pressures of approximately 0.01 torr. Using harmonic calculations for the monomer and dimer 1 values, a consistent set of structures for all four molecules was obained. The corrected monomer distances reproduce the microwave values very well. The experiment yields information on the amount of dimer present in the vapor, and these results are compared with thermodynamic values.

  6. Reverse osmosis transport of alkali halides and nickel salts through cellulose triacetate membranes. Performance prediction from NaCl experiments

    SciTech Connect

    Nirmal, J.D.; Pandya, V.P.; Desai, N.V.; Rangarajan, R. )

    1992-10-01

    The separation of alkali metal halides, nickel chloride, and nickel sulfate was determined for cellulose triacetate reverse osmosis (CTA RO) membranes. From transport analysis, the relative free energy parameters for transport of these salts through CTA membranes were determined. From these relative free energy parameters of salts, the solute separation by CTA membranes could be predicted from RO experiment with NaCl solution. The transport analysis and an illustration of how the concept is useful are presented in this paper.

  7. 40 CFR 721.5452 - Alkali metal salt of halogenated organoborate (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Alkali metal salt of halogenated... Specific Chemical Substances § 721.5452 Alkali metal salt of halogenated organoborate (generic). (a... generically as alkali metal salt of halogenated organoborate (PMN P-00-0638) is subject to reporting...

  8. 40 CFR 721.5452 - Alkali metal salt of halogenated organoborate (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Alkali metal salt of halogenated... Specific Chemical Substances § 721.5452 Alkali metal salt of halogenated organoborate (generic). (a... generically as alkali metal salt of halogenated organoborate (PMN P-00-0638) is subject to reporting...

  9. 40 CFR 721.5452 - Alkali metal salt of halogenated organoborate (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Alkali metal salt of halogenated... Specific Chemical Substances § 721.5452 Alkali metal salt of halogenated organoborate (generic). (a... generically as alkali metal salt of halogenated organoborate (PMN P-00-0638) is subject to reporting...

  10. 40 CFR 721.5452 - Alkali metal salt of halogenated organoborate (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Alkali metal salt of halogenated... Specific Chemical Substances § 721.5452 Alkali metal salt of halogenated organoborate (generic). (a... generically as alkali metal salt of halogenated organoborate (PMN P-00-0638) is subject to reporting...

  11. 40 CFR 721.5452 - Alkali metal salt of halogenated organoborate (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Alkali metal salt of halogenated... Specific Chemical Substances § 721.5452 Alkali metal salt of halogenated organoborate (generic). (a... generically as alkali metal salt of halogenated organoborate (PMN P-00-0638) is subject to reporting...

  12. 40 CFR 721.2565 - Alkylated sulfonated diphenyl oxide, alkali and amine salts.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., alkali and amine salts. 721.2565 Section 721.2565 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.2565 Alkylated sulfonated diphenyl oxide, alkali and... substances identified as alkylated sulfonated diphenyl oxide, alkali salt (PMN P-93-352) and...

  13. 40 CFR 721.2565 - Alkylated sulfonated diphenyl oxide, alkali and amine salts.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ..., alkali and amine salts. 721.2565 Section 721.2565 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.2565 Alkylated sulfonated diphenyl oxide, alkali and... substances identified as alkylated sulfonated diphenyl oxide, alkali salt (PMN P-93-352) and...

  14. 40 CFR 721.2565 - Alkylated sulfonated diphenyl oxide, alkali and amine salts.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., alkali and amine salts. 721.2565 Section 721.2565 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.2565 Alkylated sulfonated diphenyl oxide, alkali and... substances identified as alkylated sulfonated diphenyl oxide, alkali salt (PMN P-93-352) and...

  15. 40 CFR 721.5985 - Fatty alkyl phosphate, alkali metal salt (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Fatty alkyl phosphate, alkali metal... Specific Chemical Substances § 721.5985 Fatty alkyl phosphate, alkali metal salt (generic). (a) Chemical... as a fatty alkyl phosphate, alkali metal salt (PMN P-99-0385) is subject to reporting under...

  16. 40 CFR 721.5985 - Fatty alkyl phosphate, alkali metal salt (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Fatty alkyl phosphate, alkali metal... Specific Chemical Substances § 721.5985 Fatty alkyl phosphate, alkali metal salt (generic). (a) Chemical... as a fatty alkyl phosphate, alkali metal salt (PMN P-99-0385) is subject to reporting under...

  17. 40 CFR 721.5985 - Fatty alkyl phosphate, alkali metal salt (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Fatty alkyl phosphate, alkali metal... Specific Chemical Substances § 721.5985 Fatty alkyl phosphate, alkali metal salt (generic). (a) Chemical... as a fatty alkyl phosphate, alkali metal salt (PMN P-99-0385) is subject to reporting under...

  18. 40 CFR 721.5985 - Fatty alkyl phosphate, alkali metal salt (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Fatty alkyl phosphate, alkali metal... Specific Chemical Substances § 721.5985 Fatty alkyl phosphate, alkali metal salt (generic). (a) Chemical... as a fatty alkyl phosphate, alkali metal salt (PMN P-99-0385) is subject to reporting under...

  19. 40 CFR 721.5985 - Fatty alkyl phosphate, alkali metal salt (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Fatty alkyl phosphate, alkali metal... Specific Chemical Substances § 721.5985 Fatty alkyl phosphate, alkali metal salt (generic). (a) Chemical... as a fatty alkyl phosphate, alkali metal salt (PMN P-99-0385) is subject to reporting under...

  20. 40 CFR 721.10098 - Disubstituted benzoic acid, alkali metal salt (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... metal salt (generic). 721.10098 Section 721.10098 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.10098 Disubstituted benzoic acid, alkali metal salt... identified generically as disubstituted benzoic acid, alkali metal salt (PMN P-03-643) is subject...

  1. 40 CFR 721.4663 - Fluorinated carboxylic acid alkali metal salts.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... metal salts. 721.4663 Section 721.4663 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.4663 Fluorinated carboxylic acid alkali metal salts. (a) Chemical... fluorinated carboxylic acid alkali metal salts (PMNs P-95-979/980/981) are subject to reporting under...

  2. 40 CFR 721.4663 - Fluorinated carboxylic acid alkali metal salts.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... metal salts. 721.4663 Section 721.4663 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.4663 Fluorinated carboxylic acid alkali metal salts. (a) Chemical... fluorinated carboxylic acid alkali metal salts (PMNs P-95-979/980/981) are subject to reporting under...

  3. 40 CFR 721.10098 - Disubstituted benzoic acid, alkali metal salt (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... metal salt (generic). 721.10098 Section 721.10098 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.10098 Disubstituted benzoic acid, alkali metal salt... identified generically as disubstituted benzoic acid, alkali metal salt (PMN P-03-643) is subject...

  4. 40 CFR 721.10097 - Disubstituted benzenesulfonic acid, alkali metal salt (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ..., alkali metal salt (generic). 721.10097 Section 721.10097 Protection of Environment ENVIRONMENTAL... metal salt (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as disubstituted benzenesulfonic acid, alkali metal salt (PMN...

  5. 40 CFR 721.10098 - Disubstituted benzoic acid, alkali metal salt (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... metal salt (generic). 721.10098 Section 721.10098 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.10098 Disubstituted benzoic acid, alkali metal salt... identified generically as disubstituted benzoic acid, alkali metal salt (PMN P-03-643) is subject...

  6. 40 CFR 721.4663 - Fluorinated carboxylic acid alkali metal salts.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... metal salts. 721.4663 Section 721.4663 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.4663 Fluorinated carboxylic acid alkali metal salts. (a) Chemical... fluorinated carboxylic acid alkali metal salts (PMNs P-95-979/980/981) are subject to reporting under...

  7. 40 CFR 721.4663 - Fluorinated carboxylic acid alkali metal salts.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... metal salts. 721.4663 Section 721.4663 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.4663 Fluorinated carboxylic acid alkali metal salts. (a) Chemical... fluorinated carboxylic acid alkali metal salts (PMNs P-95-979/980/981) are subject to reporting under...

  8. 40 CFR 721.10097 - Disubstituted benzenesulfonic acid, alkali metal salt (generic).

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ..., alkali metal salt (generic). 721.10097 Section 721.10097 Protection of Environment ENVIRONMENTAL... metal salt (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as disubstituted benzenesulfonic acid, alkali metal salt (PMN...

  9. 40 CFR 721.10097 - Disubstituted benzenesulfonic acid, alkali metal salt (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ..., alkali metal salt (generic). 721.10097 Section 721.10097 Protection of Environment ENVIRONMENTAL... metal salt (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as disubstituted benzenesulfonic acid, alkali metal salt (PMN...

  10. 40 CFR 721.4663 - Fluorinated carboxylic acid alkali metal salts.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... metal salts. 721.4663 Section 721.4663 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.4663 Fluorinated carboxylic acid alkali metal salts. (a) Chemical... fluorinated carboxylic acid alkali metal salts (PMNs P-95-979/980/981) are subject to reporting under...

  11. 40 CFR 721.10097 - Disubstituted benzenesulfonic acid, alkali metal salt (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ..., alkali metal salt (generic). 721.10097 Section 721.10097 Protection of Environment ENVIRONMENTAL... metal salt (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as disubstituted benzenesulfonic acid, alkali metal salt (PMN...

  12. 40 CFR 721.10098 - Disubstituted benzoic acid, alkali metal salt (generic).

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... metal salt (generic). 721.10098 Section 721.10098 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.10098 Disubstituted benzoic acid, alkali metal salt... identified generically as disubstituted benzoic acid, alkali metal salt (PMN P-03-643) is subject...

  13. 40 CFR 721.10097 - Disubstituted benzenesulfonic acid, alkali metal salt (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ..., alkali metal salt (generic). 721.10097 Section 721.10097 Protection of Environment ENVIRONMENTAL... metal salt (generic). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as disubstituted benzenesulfonic acid, alkali metal salt (PMN...

  14. 40 CFR 721.10098 - Disubstituted benzoic acid, alkali metal salt (generic).

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... metal salt (generic). 721.10098 Section 721.10098 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.10098 Disubstituted benzoic acid, alkali metal salt... identified generically as disubstituted benzoic acid, alkali metal salt (PMN P-03-643) is subject...

  15. IR spectroscopy of aqueous alkali halide solutions: Pure salt-solvated water spectra and hydration numbers

    NASA Astrophysics Data System (ADS)

    Max, Jean-Joseph; Chapados, Camille

    2001-08-01

    Extrapolation techniques were used to obtain pure salt-solvated water spectra from the attenuated total reflection infrared spectra (ATR-IR) of aqueous solutions of the nine alkali halide salts LiCl, NaCl, KCl, CsCl, NaBr, KBr, NaI, KI, and CsI and the alkaline-earth chloride salt MgCl2. These salts ionize completely in water. The ions by themselves do not absorb in the IR, but their interactions with water can be observed and analyzed. A pure salt-solvated water spectrum is easier to analyze than that of a combined solution of pure water and salt-solvated water. Although the salt-solvated water spectra examined have distinctive signatures, they can be classified in three categories: those similar to NaCl; those not similar to NaCl; and MgCl2, in a class by itself. Each of the pure salt-solvated water spectra differs from that of liquid water, though the number of bands is the same. From the Gaussian band fitting, we found that the positions of the bands were fairly constant, whereas their intensities differed. The salt hydration numbers were determined: for NaCl, KCl, NaBr, KBr, and CsI solutions it is 5; for KI and MgCL2 it is 4; for NaI it is 3.5; for CsCl it is 3; and for LiCl it is 2. From these results we found that each pair of ions (monoatomic ions) of the ten salt solutions studied are close bound and form a complex in a cluster organization with a fixed number of water molecules.

  16. Physiological Evaluation of Alkali-Salt Tolerance of Thirty Switchgrass (Panicum virgatum) Lines.

    PubMed

    Hu, Guofu; Liu, Yiming; Zhang, Xunzhong; Yao, Fengjiao; Huang, Yan; Ervin, Erik H; Zhao, Bingyu

    2015-01-01

    Soil salt-alkalization is a major limiting factor for crop production in many regions. Switchgrass (Panicum virgatum L.) is a warm-season C4 perennial rhizomatous bunchgrass and a target lignocellulosic biofuel species. The objective of this study was to evaluate relative alkali-salt tolerance among 30 switchgrass lines. Tillers of each switchgrass line were transplanted into pots filled with fine sand. Two months after transplanting, plants at E5 developmental stage were grown in either half strength Hoagland's nutrient solution with 0 mM Na+ (control) or half strength Hoagland's nutrient solution with 150 mM Na+ and pH of 9.5 (alkali-salt stress treatment) for 20 d. Alkali-salt stress damaged cell membranes [higher electrolyte leakage (EL)], reduced leaf relative water content (RWC), net photosynthetic rate (Pn), stomatal conductance (gs), and transpiration rate (Tr). An alkali-salt stress tolerance trait index (ASTTI) for each parameter was calculated based on the ratio of the value under alkali-salt stress and the value under non-stress conditions for each parameter of each line. Relative alkali-salt tolerance was determined based on principal components analysis and cluster analysis of the physiological parameters and their ASTTI values. Significant differences in alkali-salt stress tolerance were found among the 30 lines. Lowland lines TEM-SEC, Alamo, TEM-SLC and Kanlow were classified as alkali-salt tolerant. In contrast, three lowland lines (AM-314/MS-155, BN-13645-64) and two upland lines (Caddo and Blackwell-1) were classified as alkali-salt sensitive. The results suggest wide variations exist in alkali-salt stress tolerance among the 30 switchgrass lines. The approach of using a combination of principal components and cluster analysis of the physiological parameters and related ASTTI is feasible for evaluating alkali-salt tolerance in switchgrass.

  17. Method for the production of uranium chloride salt

    DOEpatents

    Westphal, Brian R.; Mariani, Robert D.

    2013-07-02

    A method for the production of UCl.sub.3 salt without the use of hazardous chemicals or multiple apparatuses for synthesis and purification is provided. Uranium metal is combined in a reaction vessel with a metal chloride and a eutectic salt- and heated to a first temperature under vacuum conditions to promote reaction of the uranium metal with the metal chloride for the production of a UCl.sub.3 salt. After the reaction has run substantially to completion, the furnace is heated to a second temperature under vacuum conditions. The second temperature is sufficiently high to selectively vaporize the chloride salts and distill them into a condenser region.

  18. Apparatus and method for making metal chloride salt product

    DOEpatents

    Miller, William E.; Tomczuk, Zygmunt; Richmann, Michael K.

    2007-05-15

    A method of producing metal chlorides is disclosed in which chlorine gas is introduced into liquid Cd. CdCl.sub.2 salt is floating on the liquid Cd and as more liquid CdCl.sub.2 is formed it separates from the liquid Cd metal and dissolves in the salt. The salt with the CdCl.sub.2 dissolved therein contacts a metal which reacts with CdCl.sub.2 to form a metal chloride, forming a mixture of metal chloride and CdCl.sub.2. After separation of bulk Cd from the salt, by gravitational means, the metal chloride is obtained by distillation which removes CdCl.sub.2 and any Cd dissolved in the metal chloride.

  19. Enhancing Skin Permeation of Biphenylacetic Acid (BPA) Using Salt Formation with Organic and Alkali Metal Bases

    PubMed Central

    Pawar, Vijay; Naik, Prashant; Giridhar, Rajani; Yadav, Mange Ram

    2015-01-01

    In the present study, a series of organic and alkali metal salts of biphenylacetic acid (BPA) have been prepared and evaluated in vitro for percutaneous drug delivery. The physicochemical properties of BPA salts were determined using solubility measurements, DSC, and IR. The DSC thermogram and FTIR spectra confirmed the salt formation with organic and alkali metal bases. Among the series, salts with organic amines (ethanolamine, diethanolamine, triethanolamine, and diethylamine) had lowered melting points while the alkali metal salt (sodium) had a higher melting point than BPA. The in vitro study showed that salt formation improves the physicochemical properties of BPA, leading to improved permeability through the skin. Amongst all the prepared salts, ethanolamine salt (1b) showed 7.2- and 5.4-fold higher skin permeation than the parent drug at pH 7.4 and 5.0, respectively, using rat skin. PMID:26839810

  20. Precursor Luminescence near the Collapse of Laser-Induced Bubbles in Alkali-Salt Solutions

    PubMed Central

    Chu, Han-Ching; Vo, Sonny; Williams, Gary A.

    2014-01-01

    A precursor luminescence pulse consisting of atomic line emission is observed as much as 150 nanoseconds prior to the collapse point of laser-created bubbles in alkali-metal solutions. The timing of the emission from neutral Na, Li, and K atoms is strongly dependent on the salt concentration, which appears to result from resonant radiation trapping by the alkali atoms in the bubble. The alkali emission ends at the onset of the blackbody luminescence pulse at the bubble collapse point, and the duration of the blackbody pulse is found to be reduced by up to 30% as the alkali-salt concentration is increased. PMID:19519032

  1. 21 CFR 172.330 - Calcium pantothenate, calcium chloride double salt.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Calcium pantothenate, calcium chloride double salt..., calcium chloride double salt. The food additive calcium chloride double salt of calcium pantothenate may... information required by the Act, the following: (1) The name of the additive “calcium chloride double salt...

  2. 21 CFR 172.330 - Calcium pantothenate, calcium chloride double salt.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Calcium pantothenate, calcium chloride double salt..., calcium chloride double salt. The food additive calcium chloride double salt of calcium pantothenate may... information required by the Act, the following: (1) The name of the additive “calcium chloride double salt...

  3. 21 CFR 172.330 - Calcium pantothenate, calcium chloride double salt.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Calcium pantothenate, calcium chloride double salt..., calcium chloride double salt. The food additive calcium chloride double salt of calcium pantothenate may... information required by the Act, the following: (1) The name of the additive “calcium chloride double salt...

  4. 21 CFR 172.330 - Calcium pantothenate, calcium chloride double salt.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Calcium pantothenate, calcium chloride double salt..., calcium chloride double salt. The food additive calcium chloride double salt of calcium pantothenate may... information required by the Act, the following: (1) The name of the additive “calcium chloride double salt...

  5. 40 CFR 721.2565 - Alkylated sulfonated diphenyl oxide, alkali and amine salts.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Alkylated sulfonated diphenyl oxide... New Uses for Specific Chemical Substances § 721.2565 Alkylated sulfonated diphenyl oxide, alkali and... substances identified as alkylated sulfonated diphenyl oxide, alkali salt (PMN P-93-352) and...

  6. 40 CFR 721.2565 - Alkylated sulfonated diphenyl oxide, alkali and amine salts.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Alkylated sulfonated diphenyl oxide... New Uses for Specific Chemical Substances § 721.2565 Alkylated sulfonated diphenyl oxide, alkali and... substances identified as alkylated sulfonated diphenyl oxide, alkali salt (PMN P-93-352) and...

  7. Effects of Cations on Corrosion of Inconel 625 in Molten Chloride Salts

    NASA Astrophysics Data System (ADS)

    Zhu, Ming; Ma, Hongfang; Wang, Mingjing; Wang, Zhihua; Sharif, Adel

    2016-04-01

    Hot corrosion of Inconel 625 in sodium chloride, potassium chloride, magnesium chloride, calcium chloride and their mixtures with different compositions is conducted at 900°C to investigate the effects of cations in chloride salts on corrosion behavior of the alloy. XRD, SEM/EDS were used to analyze the compositions, phases, and morphologies of the corrosion products. The results showed that Inconel 625 suffers more severe corrosion in alkaline earth metal chloride molten salts than alkaline metal chloride molten salts. For corrosion in mixture salts, the corrosion rate increased with increasing alkaline earth metal chloride salt content in the mixture. Cations in the chloride molten salts mainly affect the thermal and chemical properties of the salts such as vapor pressure and hydroscopicities, which can affect the basicity of the molten salt. Corrosion of Inconel 625 in alkaline earth metal chloride salts is accelerated with increasing basicity.

  8. [Determination of Chloride Salt Solution by NIR Spectroscopy].

    PubMed

    Zhang, Bin; Chen, Jian-hong; Jiao, Ming-xing

    2015-07-01

    Determination of chloride salt solution by near infrared spectrum plays a very important role in Biomedicine. The near infrared spectrum analysis of Sodium chloride, potassium chloride, calcium chloride aqueous solution shows that the concentration change of chloride salt can affect hydrogen bond, resulting in the variation of near infrared spectrum of water. The temperature influence on NIR spectrum has been decreased by choosing reasonable wavelength range and the wavelength where the temperature effects are zero (isosbestic point). Chlorine salt prediction model was established based on partial least squares method and used for predicting the concentration of the chlorine ion. The impact on near infrared spectrum of the cation ionic radius, the number of ionic charge, the complex effect of ionic in water has also discussed in this article and the reason of every factor are analysed. Experimental results show that the temperature and concentration will affect the near-infrared spectrum of the solution, It is found that the effect of temperature plays the dominant role at low concentrations of chlorine salt; rather, the ionic dominates at high concentration. Chloride complexes are formed in aqueous solution, It has an effect on hydrogen bond of water combining with the cations in chlorine salt solution, Comparing different chloride solutions at the same concentration, the destruction effects of chloride complexes and catnions on the hydrogen bond of water increases in the sequences: CaCl2 >NaCl>KC. The modeling result shows that the determination coefficients (R2) = 99.97%, the root mean square error of cross validation (RM- SECV) = 4.51, and the residual prediction deviation (RPD) = 62.7, it meets the daily requirements of biochemical detection accuracy.

  9. Hydration patterns and salting effects in sodium chloride solution

    NASA Astrophysics Data System (ADS)

    Li, Weifeng; Mu, Yuguang

    2011-10-01

    The salting effects of 2M sodium chloride electrolyte are studied based on a series of model solutes with properties ranging from hydrophobic to hydrophilic. Generally, hydrophobic solutes will be salted out and hydrophilic solutes will be salted in by NaCl solution. The solvation free energy changes are highly correlated with Kirkwood-Buff integrals. The underlying mechanism resorts to the preferential binding of ions and water to solutes. Our results demonstrate that the salting effect not only depends on the salt's position in Hofmeister series, but also on the solutes' specifics. Taking the hydration free energies of solutes and ions as independent variables, a schematic diagram of salting effects is suggested. The resolved multifaceted salting effects rely on the sensitive balance of the tripartite interaction among solutes, ions, and water.

  10. Hydration patterns and salting effects in sodium chloride solution.

    PubMed

    Li, Weifeng; Mu, Yuguang

    2011-10-07

    The salting effects of 2M sodium chloride electrolyte are studied based on a series of model solutes with properties ranging from hydrophobic to hydrophilic. Generally, hydrophobic solutes will be salted out and hydrophilic solutes will be salted in by NaCl solution. The solvation free energy changes are highly correlated with Kirkwood-Buff integrals. The underlying mechanism resorts to the preferential binding of ions and water to solutes. Our results demonstrate that the salting effect not only depends on the salt's position in Hofmeister series, but also on the solutes' specifics. Taking the hydration free energies of solutes and ions as independent variables, a schematic diagram of salting effects is suggested. The resolved multifaceted salting effects rely on the sensitive balance of the tripartite interaction among solutes, ions, and water.

  11. Is sodium chloride worth its salt?

    PubMed

    McIntosh, Euan; Andrews, Peter J

    2013-06-11

    The choice of fluid for resuscitation of the brain-injured patient remains controversial, and the 'ideal' resuscitation fluid has yet to be identified. Large volumes of hypotonic solutions must be avoided because of the risk of cerebral swelling and intracranial hypertension. Traditionally, 0.9% sodium chloride has been used in patients at risk of intracranial hypertension, but there is increasing recognition that 0.9% saline is not without its problems. Roquilly and colleagues show a reduction in the development of hyperchloremic acidosis in brain-injured patients given 'balanced' solutions for maintenance and resuscitation compared with 0.9% sodium chloride. In this commentary, we explore the idea that we should move away from 0.9% sodium chloride in favor of a more 'physiological' solution.

  12. In situ formation of coal gasification catalysts from low cost alkali metal salts

    DOEpatents

    Wood, Bernard J.; Brittain, Robert D.; Sancier, Kenneth M.

    1985-01-01

    A carbonaceous material, such as crushed coal, is admixed or impregnated with an inexpensive alkali metal compound, such as sodium chloride, and then pretreated with a stream containing steam at a temperature of 350.degree. to 650.degree. C. to enhance the catalytic activity of the mixture in a subsequent gasification of the mixture. The treatment may result in the transformation of the alkali metal compound into another, more catalytically active, form.

  13. Structure of complexes between aluminum chloride and other chlorides, 2: Alkali-(chloroaluminates). Gaseous complexes

    NASA Technical Reports Server (NTRS)

    Hargittai, M.

    1980-01-01

    The structural chemistry of complexes between aluminum chloride and other metal chlorides is important both for practice and theory. Condensed-phase as well as vapor-phase complexes are of interest. Structural information on such complexes is reviewed. The first emphasis is given to the molten state because of its practical importance. Aluminum chloride forms volatile complexes with other metal chlorides and these vapor-phase complexes are dealt with in the second part. Finally, the variations in molecular shape and geometrical parameters are summarized.

  14. Studies on interfacial behavior and wettability change phenomena by ionic and nonionic surfactants in presence of alkalis and salt for enhanced oil recovery

    NASA Astrophysics Data System (ADS)

    Kumar, Sunil; Mandal, Ajay

    2016-05-01

    Surfactant flooding is one of the most promising method of enhanced oil recovery (EOR) used after the conventional water flooding. The addition of alkali improves the performance of surfactant flooding due to synergistic effect between alkali and surfactant on reduction of interfacial tension (IFT), wettability alteration and emulsification. In the present study the interfacial tension, contact angle, emulsification and emulsion properties of cetyltrimethylammonium bromide (CTAB), sodium dodecyl sulfate (SDS) and polysorbate 80 (Tween 80) surfactants against crude oil have been investigated in presence of sodium chloride (NaCl) and alkalis viz. sodium hydroxide (NaOH), sodium carbonate (Na2CO3), ammonium hydroxide (NH4OH), sodium metaborate (SMB) and diethanolamine (DEA). All three surfactants significantly reduce the IFT values, which are further reduced to ultra-low value (∼10-4 mN/m) by addition of alkalis and salt. It has been found experimentally that alkali-surfactant systems change the wettability of an intermediate-wet quartz rock to water-wet. Emulsification of crude oil by surfactant and alkali has also been investigated in terms of the phase volume and stability of emulsion. A comparative FTIR analysis of crude oil and different emulsions were performed to investigate the interactions between crude oil and displacing water in presence of surfactant and alkali.

  15. Effects of magnesium and chloride ions on limestone dual-alkali-system performance

    SciTech Connect

    Chang, J.C.S.; Kaplan, N.; Brna, T.G.

    1985-08-01

    The paper gives results of pilot plant tests to evaluate the effects of magnesium and chloride ions on system performance of limestone-regenerated dual alkali processes under closed-loop operating conditions. It was found that limestone reactivity and solids dewatering properties are very sensitive to magnesium ion concentrations. The total magnesium ion concentration should be maintained below 1000 ppm for satisfactory performance under normal operation. A model which assumes competitive surface adsorption of calcium and magnesium ions was used to interpret the data. Limestone reactivity and solids dewatering properties decreased with the increase of chloride ion concentrations; however, the effect of chloride ion accumulation was not significant until the concentration reached 80,000 ppm.

  16. 21 CFR 172.330 - Calcium pantothenate, calcium chloride double salt.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Calcium pantothenate, calcium chloride double salt... Dietary and Nutritional Additives § 172.330 Calcium pantothenate, calcium chloride double salt. The food additive calcium chloride double salt of calcium pantothenate may be safely used in foods for...

  17. Dechlorination and stabilization of radioactive chloride salt waste in a molten state

    SciTech Connect

    In-Tae Kim; Hwan-Seo Park; Yong-Jun Cho; Hwan-Young Kim; Seong-Won Park; Eung-Ho Kim

    2007-07-01

    This study suggests a new method to stabilize the molten salt wastes generated from he pyro-processing of a LWR spent fuel. Using a conventional sol-gel process, an inorganic material (SiO{sub 2}-Al{sub 2}O{sub 3}-P{sub 2}O{sub 5}, SAP) reactive to metal chlorides was prepared. In this paper, the reactivity of the SAP on the metal chlorides at 650-850 deg. C, the thermal stability of the reaction products and their leach-resistance under the PCT-A leach test were investigated. In the SAP, three different kinds of chains are available; Si-O-Si (main chain), Si-O-Al (side chain) and Al-O-P/P-O-P (reactive chain). Alkali metal chlorides were converted into metal aluminosilicate (Li{sub x}Al{sub x}Si{sub 1-x}O{sub 2-x}) and metal phosphate(Li{sub 3}PO{sub 4} and Cs{sub 2}AlP{sub 3}O{sub 10}) while the alkaline earth and rare earth chlorides were changed into only metal phosphates (Sr{sub 5}(PO{sub 4}){sub 3}Cl and CePO{sub 4}). The conversion rate was about 96% at a salt waste/SAP weight ratio of 0.5 and a weight loss up to 1100 deg. C measured by the thermo-gravimetric analysis was below 1 Wt%. The leach rates of Cs and Sr under the PCT-A leaching condition were about 10{sup -2} and 10{sup -4} g/m{sup 3}.day, respectively. From these results, it could be concluded that the SAP developed in this study can be considered as an effective stabilizer for metal chlorides and the method of using the SAP could provide a chance to minimize the final waste volume to be disposed off. (authors)

  18. Chemistry and Spectroscopy of Frozen Chloride Salts on Icy Bodies

    NASA Astrophysics Data System (ADS)

    Johnson, Paul; Thomas, Elena C.; Hodyss, Robert; Vu, Tuan; Choukroun, Mathieu

    2016-10-01

    Currently, our understanding of the chemical composition of Europa's surface is our best means of inferring constraints on the subsurface ocean composition and its subsequent habitability. The bulk of our knowledge of Europa surface chemistry can be traced to near infrared spectra recorded by the Near Infrared Mapping Spectrometer on the Galileo spacecraft. However, the usefulness of this and other remote sensing data is limited by the availability of spectral libraries of candidate materials under relevant conditions (temperature, thermal/radiation history, etc.). Chloride salts are expected to exist on the surface of Europa, and other icy bodies, based on geochemical predictions of the ocean composition. In order to help improve our understanding of Europa's surface composition, we have conducted a study of frozen chloride-salt brines prepared under simulated Europa surface conditions (vacuum, temperature, and UV irradiation) using both near IR and Raman spectroscopies. Specifically, Raman spectroscopy was used to determine the hydration states of various chloride salts as a function of temperature. Near IR spectroscopy of identically prepared samples was used to provide reference reflectance spectra of the identified hydrated salts. Our results indicate that at temperatures ranging from 80 K to 233 K, hydrohalite is formed from the freezing of NaCl brines, while the freezing of KCl solutions does not form KCl hydrates. In addition, the freezing of MgCl2 solutions forms a stable hexahydrate, and the freezing of CaCl2 solutions forms a hexahydrate, a tetrahydrate, and a dihydrate. Dehydration of the salts was observed as temperatures were increased, leading to a succession of hydration states in the case of CaCl2.

  19. Partitioning of Alkali Metal Salts and Boric Acid from Aqueous Phase into the Polyamide Active Layers of Reverse Osmosis Membranes.

    PubMed

    Wang, Jingbo; Kingsbury, Ryan S; Perry, Lamar A; Coronell, Orlando

    2017-02-21

    The partition coefficient of solutes into the polyamide active layer of reverse osmosis (RO) membranes is one of the three membrane properties (together with solute diffusion coefficient and active layer thickness) that determine solute permeation. However, no well-established method exists to measure solute partition coefficients into polyamide active layers. Further, the few studies that measured partition coefficients for inorganic salts report values significantly higher than one (∼3-8), which is contrary to expectations from Donnan theory and the observed high rejection of salts. As such, we developed a benchtop method to determine solute partition coefficients into the polyamide active layers of RO membranes. The method uses a quartz crystal microbalance (QCM) to measure the change in the mass of the active layer caused by the uptake of the partitioned solutes. The method was evaluated using several inorganic salts (alkali metal salts of chloride) and a weak acid of common concern in water desalination (boric acid). All partition coefficients were found to be lower than 1, in general agreement with expectations from Donnan theory. Results reported in this study advance the fundamental understanding of contaminant transport through RO membranes, and can be used in future studies to decouple the contributions of contaminant partitioning and diffusion to contaminant permeation.

  20. 40 CFR 721.10630 - Amino acid, carboxyalkyl, alkylsulfonate, alkali salt (generic).

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Amino acid, carboxyalkyl... Significant New Uses for Specific Chemical Substances § 721.10630 Amino acid, carboxyalkyl, alkylsulfonate... chemical substances identified generically as amino acid, carboxyalkyl, alkylsulfonate, alkali salts...

  1. 40 CFR 721.10630 - Amino acid, carboxyalkyl, alkylsulfonate, alkali salt (generic).

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Amino acid, carboxyalkyl... Significant New Uses for Specific Chemical Substances § 721.10630 Amino acid, carboxyalkyl, alkylsulfonate... chemical substances identified generically as amino acid, carboxyalkyl, alkylsulfonate, alkali salts...

  2. Oxygen production by molten alkali metal salts using multiple absorption-desorption cycles

    DOEpatents

    Cassano, Anthony A.

    1985-01-01

    A continuous chemical air separation is performed wherein oxygen is recovered with a molten alkali metal salt oxygen acceptor in a series of absorption zones which are connected to a plurality of desorption zones operated in separate parallel cycles with the absorption zones. A greater recovery of high pressure oxygen is achieved at reduced power requirements and capital costs.

  3. Oxygen production by molten alkali metal salts using multiple absorption-desorption cycles

    DOEpatents

    Cassano, A.A.

    1985-07-02

    A continuous chemical air separation is performed wherein oxygen is recovered with a molten alkali metal salt oxygen acceptor in a series of absorption zones which are connected to a plurality of desorption zones operated in separate parallel cycles with the absorption zones. A greater recovery of high pressure oxygen is achieved at reduced power requirements and capital costs. 3 figs.

  4. Hydrodynamic simulation of a lithium chloride salt system.

    SciTech Connect

    Eberle, C. S.; Herrmann, S. D.; Knighton, G. C.

    1999-02-12

    A fused lithium chloride salt system's constitutive properties were evaluated and compared to a number of fluid properties, and water was shown to be an excellent simulant of lithium chloride salt. With a simple flow model, the principal scaling term was shown to be a function of the kinematic viscosity. A water mock-up of the molten salt was also shown to be within a {+-}3% error in the scaling analysis. This made it possible to consider developing water scaled tests of the molten salt system. Accurate flow velocity and pressure measurements were acquired by developing a directional velocity probe. The device was constructed and calibrated with a repeatable accuracy of {+-}15%. This was verified by a detailed evaluation of the probe. Extensive flow measurements of the engineering scale mockup were conducted, and the results were carefully compared to radial flow patterns of a straight blade stirrer. The flow measurements demonstrated an anti-symmetric nature of the stirring, and many additional effects were also identified. The basket design was shown to prevent fluid penetration into the fuel baskets when external stirring was the flow mechanism.

  5. Burner rig alkali salt corrosion of several high temperature alloys

    NASA Technical Reports Server (NTRS)

    Deadmore, D. L.; Lowell, C. E.

    1977-01-01

    The hot corrosion of five alloys was studied in cyclic tests in a Mach 0.3 burner rig into whose combustion chamber various aqueous salt solutions were injected. Three nickel-based alloys, a cobalt-base alloy, and an iron-base alloy were studied at temperatures of 700, 800, 900, and 1000 C with various salt concentrations and compositions. The relative resistance of the alloys to hot corrosion attack was found to vary with temperature and both concentration and composition of the injected salt solution. Results indicate that the corrosion of these alloys is a function of both the presence of salt condensed as a liquid on the surface and of the composition of the gas phases present.

  6. Burner rig alkali salt corrosion of several high temperature alloys

    NASA Technical Reports Server (NTRS)

    Deadmore, D.; Lowell, C.

    1977-01-01

    The hot corrosion of five alloys was studied in cyclic tests in a Mach 0.3 burner rig into whose combustion chamber various aqueous salt solutions were injected. Three nickel-base alloys (IN-792, IN-738, and IN-100), a cobalt-base alloy (MM-509), and an iron-base alloy (304 stainless steel) were studied at temperatures of 700, 800, 900, and 1000 C with various salt concentrations and compositions. The relative resistance of the alloys to hot corrosion attack was found to vary with temperature and with both the concentration and composition of the injected salt solution. Results indicate that the corrosion of these alloys is a function of both the presence of salt condensed as a liquid on the surface and of the composition of the gas phases present.

  7. Salting out of methane by sodium chloride: A scaled particle theory study.

    PubMed

    Graziano, Giuseppe

    2008-08-28

    The salting out of methane by adding NaCl to water at 25 degrees C and 1 atm is investigated by calculating the work of cavity creation by means of scaled particle theory and the methane-solvent energy of attraction. The latter quantity changes to little extent on passing from pure water to an aqueous 4M NaCl solution, whereas the magnitude of the work of cavity creation increases significantly, accounting for the salting out effect. There is quantitative agreement between the experimental values of the hydration Gibbs energy and the calculated ones. The behavior of the work of cavity creation is due to the increase in the volume packing density of NaCl solutions, since the average effective molecular diameter does not change, being always 2.80 A. The same approach allows the rationalization of the difference in methane salting out along the alkali chloride series. These results indicate that, fixed the aqueous solution density, the solubility of nonpolar species is mainly determined by the effective diameter of solvent molecules and the corresponding volume packing density. There is no need to take into account the H-bond rearrangement because it is characterized by an almost complete enthalpy-entropy compensation.

  8. Novel ternary molten salt electrolytes for intermediate-temperature sodium/nickel chloride batteries

    NASA Astrophysics Data System (ADS)

    Li, Guosheng; Lu, Xiaochuan; Coyle, Christopher A.; Kim, Jin Y.; Lemmon, John P.; Sprenkle, Vincent L.; Yang, Zhenguo

    2012-12-01

    The sodium-nickel chloride (ZEBRA) battery is operated at relatively high temperature (250-350 °C) to achieve adequate electrochemical performance. Reducing the operating temperature in the range of 150200 °C can not only lead to enhanced cycle life by suppressing temperature-related degradations, but also allow the use of lower cost materials for construction. To achieve adequate electrochemical performance at lower operating temperatures, reduction in ohmic losses is required, including the reduced ohmic resistance of β″-alumina solid electrolyte (BASE) and the incorporation of low melting point secondary electrolytes. In present work, planar-type Na/NiCl2 cells with a thin BASE (600 μm) and low melting point secondary electrolyte were evaluated at reduced temperatures. Molten salts used as secondary electrolytes were fabricated by the partial replacement of NaCl in the standard secondary electrolyte (NaAlCl4) with other lower melting point alkali metal salts such as NaBr, LiCl, and LiBr. Electrochemical characterization of these ternary molten salts demonstrated improved ionic conductivity and sufficient electrochemical window at reduced temperatures. Furthermore, Na/NiCl2 cells with 50 mol% NaBr-containing secondary electrolyte exhibited reduced polarizations at 175 °C compared to the cell with the standard NaAlCl4 catholyte. The cells also exhibited stable cycling performance even at 150 °C.

  9. Novel ternary molten salt electrolytes for intermediate-temperature sodium/nickel chloride batteries

    SciTech Connect

    Li, Guosheng; Lu, Xiaochuan; Coyle, Christopher A.; Kim, Jin Y.; Lemmon, John P.; Sprenkle, Vincent L.; Yang, Zhenguo

    2012-12-15

    The sodium–nickel chloride (ZEBRA) battery is operated at relatively high temperature (250–350 °C) to achieve adequate electrochemical performance. Reducing the operating temperature in the range of 150200 °C can not only lead to enhanced cycle life by suppressing temperature-related degradations, but also allow the use of lower cost materials for construction. To achieve adequate electrochemical performance at lower operating temperatures, reduction in ohmic losses is required, including the reduced ohmic resistance of β"-alumina solid electrolyte (BASE) and the incorporation of low melting point secondary electrolytes. In present work, planar-type Na/NiCl2 cells with a thin BASE (600 μm) and low melting point secondary electrolyte were evaluated at reduced temperatures. Molten salts used as secondary electrolytes were fabricated by the partial replacement of NaCl in the standard secondary electrolyte (NaAlCl4) with other lower melting point alkali metal salts such as NaBr, LiCl, and LiBr. Electrochemical characterization of these ternary molten salts demonstrated improved ionic conductivity and sufficient electrochemical window at reduced temperatures. Furthermore, Na/NiCl2 cells with 50 mol% NaBr-containing secondary electrolyte exhibited reduced polarizations at 175 °C compared to the cell with the standard NaAlCl4 catholyte. Finally, the cells also exhibited stable cycling performance even at 150 °C.

  10. Solubility of some alkali and alkaline earth chlorides in water at moderate temperatures

    USGS Publications Warehouse

    Clynne, M.A.; Potter, R.W.

    1979-01-01

    Solubilities for the binary systems, salt-H2O, of the chlorides of lithium, rubidium, cesium, magnesium, calcium, strontium, and barium from near 0??C to the saturated boiling point are reported. The experimental data and coefficients of an equation for a smoothed curve describing each system are listed in the tables. The data are improvements on those previously reported in the literature, having a precision on the average of ??0.09%.

  11. Molten Chloride Salts for Heat Transfer in Nuclear Systems

    NASA Astrophysics Data System (ADS)

    Ambrosek, James Wallace

    2011-12-01

    A forced convection loop was designed and constructed to examine the thermal-hydraulic performance of molten KCl-MgCl2 (68-32 at %) salt for use in nuclear co-generation facilities. As part of this research, methods for prediction of the thermo-physical properties of salt mixtures for selection of the coolant salt were studied. In addition, corrosion studies of 10 different alloys were exposed to the KCl-MgCl2 to determine a suitable construction material for the loop. Using experimental data found in literature for unary and binary salt systems, models were found, or developed to extrapolate the available experimental data to unstudied salt systems. These property models were then used to investigate the thermo-physical properties of the LINO3-NaNO3-KNO 3-Ca(NO3), system used in solar energy applications. Using these models, the density, viscosity, adiabatic compressibility, thermal conductivity, heat capacity, and melting temperatures of higher order systems can be approximated. These models may be applied to other molten salt systems. Coupons of 10 different alloys were exposed to the chloride salt for 100 hours at 850°C was undertaken to help determine with which alloy to construct the loop. Of the alloys exposed, Haynes 230 had the least amount of weight loss per area. Nickel and Hastelloy N performed best based on maximum depth of attack. Inconel 625 and 718 had a nearly uniform depletion of Cr from the surface of the sample. All other alloys tested had depletion of Cr along the grain boundaries. The Nb in Inconel 625 and 718 changed the way the Cr is depleted in these alloys. Grain-boundary engineering (GBE) of Incoloy 800H improved the corrosion resistance (weight loss and maximum depth of attack) by nearly 50% as compared to the as-received Incoloy 800H sample. A high temperature pump, thermal flow meter, and pressure differential device was designed, constructed and tested for use in the loop, The heat transfer of the molten chloride salt was found to

  12. Method of preparing sodalite from chloride salt occluded zeolite

    SciTech Connect

    Lewis, Michele A.; Pereira, Candido

    1997-01-01

    A method for immobilizing waste chloride salts containing radionuclides and hazardous nuclear material for permanent disposal starting with a substantially dry zeolite and sufficient glass to form leach resistant sodalite with occluded radionuclides and hazardous nuclear material. The zeolite and glass are heated to a temperature up to about 1000.degree. K. to convert the zeolite to sodalite and thereafter maintained at a pressure and temperature sufficient to form a sodalite product near theoretical density. Pressure is used on the formed sodalite to produce the required density.

  13. Method of preparing sodalite from chloride salt occluded zeolite

    DOEpatents

    Lewis, M.A.; Pereira, C.

    1997-03-18

    A method is described for immobilizing waste chloride salts containing radionuclides and hazardous nuclear material for permanent disposal starting with a substantially dry zeolite and sufficient glass to form leach resistant sodalite with occluded radionuclides and hazardous nuclear material. The zeolite and glass are heated to a temperature up to about 1000 K to convert the zeolite to sodalite and thereafter maintained at a pressure and temperature sufficient to form a sodalite product near theoretical density. Pressure is used on the formed sodalite to produce the required density.

  14. Method of preparing sodalite from chloride salt occluded zeolite A

    SciTech Connect

    Lewis, M.A.; Pereira, C.

    1995-12-31

    A method is described for immobilizing waste chloride salts containing radionuclides and hazardous nuclear material for permanent disposal starting with a substantially dry zeolite and sufficient glass to form leach resistance sodalite with occluded radionuclides and hazardous nuclear material. The zeolite and glass are heated to a temperature up to about 1,000 K to convert the zeolite to sodalite and thereafter maintained at a pressure and temperature sufficient to form a sodalite product near theoretical density. Pressure is used on the formed sodalite to produce the required density.

  15. The salt (sodium chloride) requirements of growing bobwhite quail

    USGS Publications Warehouse

    Nestler, R.B.

    1949-01-01

    In the two experiments involving 452 bobwhite quail chicks, seven diets containing the following salt supplements, were compared: No additional salt; 0.25 per cent KaCl; 0.50 per cent NaC1; 0.75per cent NaCl; 1.00 per cent NaCl; 0.25 per cent Na2SO4; and 0.50 per cent KCl. All four diets containing sodium chloride gave about equal results in bird-growth, and produced better weights than the diet containing no additional salt. Survival was high on the 0.50, 0.75 and 1.00 per cent levels, especially the 0.75 per cent level. Feed consumption increased directly as the salt level of the diet was raised.....The results on the Na2SO4 and KCl while better than those on no saline supplementation, and somewhat inferior to those on NaCl, nevertheless are inconclusive because of inconsistency.

  16. Heteroatom-Containing Porous Carbons Derived from Ionic Liquid-Doped Alkali Organic Salts for Supercapacitors.

    PubMed

    Zhu, Jingyue; Xu, Dan; Qian, Wenjing; Zhang, Jinyu; Yan, Feng

    2016-04-13

    A simple strategy for the synthesis of heteroatom-doped porous carbon materials (CMs) via using ionic liquid (IL)-doped alkali organic salts as small molecular precursors is developed. Doping of alkali organic salts (such as sodium glutamate, sodium tartrate, and sodium citrate) with heteroatoms containing ILs (including 1-butyl-3-methylimidazolium chlorine and 3-butyl-4-methythiazolebromination) not only incorporates the heteroatoms into the carbon frameworks but also highly improves the carbonization yield, as compared with that of either alkali organic salts or ILs as precursors. The porous structure of CMs can be tuned by adjusting the feed ratio of ILs. The porous CMs derived from 1-butyl-3-methylimidazolium chlorine-doped sodium glutamate exhibit high charge storage capacity with a specific capacitance of 287 F g(-1) and good stability over 5000 cycles in 6 m KOH at a current density of 1 A g(-1) for supercapacitors. This strategy opens a simple and efficient method for the synthesis of heteroatom-doped porous CMs.

  17. Alkali Metal Suboxometalates-Structural Chemistry between Salts and Metals.

    PubMed

    Wörsching, Matthias; Hoch, Constantin

    2015-07-20

    The crystal structures of the new cesium-poor alkali metal suboxometalates Cs10MO5 (M = Al, Ga, Fe) show both metallic and ionic bonding following the formal description (Cs(+))10(MO4(5-))(O(2-))·3e(-). Comparable to the cesium-rich suboxometalates Cs9MO4 (M = Al, Ga, In, Fe, Sc) with ionic subdivision (Cs(+))9(MO4(5-))·4e(-), they contain an oxometalate anion [M(III)O4](5-) embedded in a metallic matrix of cesium atoms. Columnlike building units form with prevalent ionic bonding inside and metallic bonding on the outer surface. In the cesium-rich suboxometalates Cs9MO4, additional cesium atoms with no contact to any anion are inserted between columns of the formal composition [Cs8MO4]. In the cesium-poor suboxometalates Cs10MO5, the same columns are extended by face-sharing [Cs6O] units, and no additional cesium atoms are present. The terms "cesium-rich" and "cesium-poor" here refer to the Cs:O ratio. The new suboxometalates Cs10MO5 crystallize in two modifications with new structure types. The orthorhombic modification adopts a structure with four formula units per unit cell in space group Pnnm with a = 11.158(3) Å, b = 23.693(15) Å, and c = 12.229(3) Å for Cs10AlO5. The monoclinic modification crystallizes with eight formula units per unit cell in space group C2/c with a = 21.195(3) Å, b = 12.480(1) Å, c = 24.120(4) Å, and β = 98.06(1)° for Cs10AlO5. Limits to phase formation are given by the restriction that the M atoms must be trivalent and by geometric size restrictions for the insertion of [Cs6O] blocks in Cs10MO5. All of the suboxometalate structures show similar structural details and form mixed crystal series with statistical occupation for the M elements following the patterns Cs9(M(1)xM(2)1-x)O4 and Cs10(M(1)xM(2)1-x)O5. The suboxometalates are a new example of ordered intergrowth of ionic and metallic structure elements, allowing for the combination of properties related to both ionic and metallic materials.

  18. Method for immobilizing mixed waste chloride salts containing radionuclides and other hazardous wastes

    DOEpatents

    Lewis, Michele A.; Johnson, Terry R.

    1993-09-07

    The invention is a method for the encapsulation of soluble radioactive waste chloride salts containing radionuclides such as strontium, cesium and hazardous wastes such as barium so that they may be permanently stored without future threat to the environment. The process consists of contacting the salts containing the radionuclides and hazardous wastes with certain zeolites which have been found to ion exchange with the radionuclides and to occlude the chloride salts so that the resulting product is leach resistant.

  19. Method for immobilizing mixed waste chloride salts containing radionuclides and other hazardous wastes

    DOEpatents

    Lewis, Michele A.; Johnson, Terry R.

    1993-01-01

    The invention is a method for the encapsulation of soluble radioactive waste chloride salts containing radionuclides such as strontium, cesium and hazardous wastes such as barium so that they may be permanently stored without future threat to the environment. The process consists of contacting the salts containing the radionuclides and hazardous wastes with certain zeolites which have been found to ion exchange with the radionuclides and to occlude the chloride salts so that the resulting product is leach resistant.

  20. Over-expression of a novel JAZ family gene from Glycine soja, increases salt and alkali stress tolerance.

    PubMed

    Zhu, Dan; Cai, Hua; Luo, Xiao; Bai, Xi; Deyholos, Michael K; Chen, Qin; Chen, Chao; Ji, Wei; Zhu, Yanming

    2012-09-21

    Salt and alkali stress are two of the main environmental factors limiting crop production. Recent discoveries show that the JAZ family encodes plant-specific genes involved in jasmonate signaling. However, there is only limited information about this gene family in abiotic stress response, and in wild soybean (Glycine soja), which is a species noted for its tolerance to alkali and salinity. Here, we isolated and characterized a novel JAZ family gene, GsJAZ2, from G. soja. Transcript abundance of GsJAZ2 increased following exposure to salt, alkali, cold and drought. Over-expression of GsJAZ2 in Arabidopsis resulted in enhanced plant tolerance to salt and alkali stress. The expression levels of some alkali stress response and stress-inducible marker genes were significantly higher in the GsJAZ2 overexpression lines as compared to wild-type plants. Subcellular localization studies using a GFP fusion protein showed that GsJAZ2 was localized to the nucleus. These results suggest that the newly isolated wild soybean GsJAZ2 is a positive regulator of plant salt and alkali stress tolerance.

  1. The fate of minor alkali elements in the chemical evolution of salt lakes

    PubMed Central

    2011-01-01

    Alkaline earth elements and alkali metals (Mg, Ca, Na and K) play an important role in the geochemical evolution of saline lakes as the final brine type is defined by the abundance of these elements. The role of major ions in brine evolution has been studied in great detail, but little has been done to investigate the behaviour of minor alkali elements in these systems despite their similar chemical affinities to the major cations. We have examined three major anionic brine types, chloride, sulphate, and bicarbonate-carbonate, in fifteen lakes in North America and Antarctica to determine the geochemical behaviour of lithium, rubidium, strontium, and barium. Lithium and rubidium are largely conservative in all water types, and their concentrations are the result of long-term solute input and concentration through evaporation and/or sublimation. Strontium and barium behaviours vary with anionic brine type. Strontium can be removed in sulphate and carbonate-rich lakes by the precipitation of carbonate minerals. Barium may be removed in chloride and sulphate brines by either the precipitation of barite and perhaps biological uptake. PMID:21992434

  2. (-)-Epicatechin gallate prevents alkali-salt mediated fibrillogenesis of hen egg white lysozyme.

    PubMed

    Ghosh, Sudeshna; Pandey, Nitin K; Dasgupta, Swagata

    2013-03-01

    Green tea polyphenols (GTPs) are found to be potent inhibitors of amyloid fibril formation. We report the effective inhibitory property of (-)-epicatechin gallate (ECG) during the alkali-salt induced fibrillogenesis of hen egg white lysozyme (HEWL) at 37 °C. Spectroscopic techniques such as fluorescence, circular dichroism and microscopic images show that (-)-epigallocatechin (EGC), (-)-epicatechin gallate (ECG), and (-)-epigallocatechin gallate (EGCG) show moderate inhibition of fibrillation with ECG as the most potent polyphenol. Aromatic interactions, hydrophobic interactions, the radical scavenging activity and autoxidation of polyphenols are likely to be the major reasons for ECG being the most effective inhibitor.

  3. Alkali-aggregate reaction under the influence of deicing salts in the Hokuriku district, Japan

    SciTech Connect

    Katayama, Tetsuya . E-mail: katayamat@kge.co.jp; Tagami, Masahiko; Sarai, Yoshinori; Izumi, Satoshi; Hira, Toshikatsu

    2004-11-15

    Concrete cores taken from highway bridges and culverts undergoing alkali-silica reaction (ASR) were investigated petrographically by means of core scanning, point counting, polarizing microscopy, scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), electron-probe microanalysis with energy-dispersive spectrometry, in conjunction with wet chemical analyses and expansion tests. Field damage was roughly proportional to the content of andesite in the gravel aggregates due to the presence of highly reactive cristobalite and tridymite. Electron-probe microanalyzer analysis of unhydrated cement phases in the concrete revealed that the cement used had contained at least 0.5% to 1.0% alkali (Na{sub 2}Oeq) and that both the aggregates and the deicing salts had supplied part of the water-soluble alkali to concrete toward the threshold of producing ASR (Na{sub 2}O{sub eq} 3.0 kg/m{sup 3}). An accelerated concrete core expansion test (1 M NaOH, 80 deg. C) of the damaged structures mostly gave core expansions of >0.10% at 21 days (or >0.05% at 14 days), nearly comparable to those of a slow expansion test with saturated NaCl solution (50 deg. C, 91 days) which produced Cl-containing ASR gel.

  4. Methanol synthesis using a catalyst combination of alkali or alkaline earth salts and reduced copper chromite

    DOEpatents

    Tierney, J.W.; Wender, I.; Palekar, V.M.

    1995-01-24

    The present invention relates to a novel route for the synthesis of methanol, and more specifically to the production of methanol by contacting synthesis gas under relatively mild conditions in a slurry phase with a catalyst combination comprising reduced copper chromite and basic alkali salts or alkaline earth salts. The present invention allows the synthesis of methanol to occur in the temperature range of approximately 100--160 C and the pressure range of 40--65 atm. The process produces methanol with up to 90% syngas conversion per pass and up to 95% methanol selectivity. The only major by-product is a small amount of easily separated methyl formate. Very small amounts of water, carbon dioxide and dimethyl ether are also produced. The present catalyst combination also is capable of tolerating fluctuations in the H[sub 2]/CO ratio without major deleterious effect on the reaction rate. Furthermore, carbon dioxide and water are also tolerated without substantial catalyst deactivation.

  5. Methanol synthesis using a catalyst combination of alkali or alkaline earth salts and reduced copper chromite

    DOEpatents

    Tierney, John W.; Wender, Irving; Palekar, Vishwesh M.

    1995-01-01

    The present invention relates to a novel route for the synthesis of methanol, and more specifically to the production of methanol by contacting synthesis gas under relatively mild conditions in a slurry phase with a catalyst combination comprising reduced copper chromite and basic alkali salts or alkaline earth salts. The present invention allows the synthesis of methanol to occur in the temperature range of approximately 100.degree.-160.degree. C. and the pressure range of 40-65 atm. The process produces methanol with up to 90% syngas conversion per pass and up to 95% methanol selectivity. The only major by-product is a small amount of easily separated methyl formate. Very small amounts of water, carbon dioxide and dimethyl ether are also produced. The present catalyst combination also is capable of tolerating fluctuations in the H.sub.2 /CO ratio without major deleterious effect on the reaction rate. Furthermore, carbon dioxide and water are also tolerated without substantial catalyst deactivation.

  6. Over-expression of a novel JAZ family gene from Glycine soja, increases salt and alkali stress tolerance

    SciTech Connect

    Zhu, Dan; Cai, Hua; Luo, Xiao; Bai, Xi; Deyholos, Michael K.; Chen, Qin; Chen, Chao; Ji, Wei; Zhu, Yanming

    2012-09-21

    Highlights: Black-Right-Pointing-Pointer We isolated and characterized a novel JAZ family gene, GsJAZ2, from Glycine soja. Black-Right-Pointing-Pointer Overexpression of GsJAZ2 enhanced plant tolerance to salt and alkali stress. Black-Right-Pointing-Pointer The transcriptions of stress marker genes were higher in GsJAZ2 overexpression lines. Black-Right-Pointing-Pointer GsJAZ2 was localized to nucleus. -- Abstract: Salt and alkali stress are two of the main environmental factors limiting crop production. Recent discoveries show that the JAZ family encodes plant-specific genes involved in jasmonate signaling. However, there is only limited information about this gene family in abiotic stress response, and in wild soybean (Glycine soja), which is a species noted for its tolerance to alkali and salinity. Here, we isolated and characterized a novel JAZ family gene, GsJAZ2, from G. soja. Transcript abundance of GsJAZ2 increased following exposure to salt, alkali, cold and drought. Over-expression of GsJAZ2 in Arabidopsis resulted in enhanced plant tolerance to salt and alkali stress. The expression levels of some alkali stress response and stress-inducible marker genes were significantly higher in the GsJAZ2 overexpression lines as compared to wild-type plants. Subcellular localization studies using a GFP fusion protein showed that GsJAZ2 was localized to the nucleus. These results suggest that the newly isolated wild soybean GsJAZ2 is a positive regulator of plant salt and alkali stress tolerance.

  7. Constraints on the composition and particle size of chloride salt-bearing deposits on Mars

    NASA Astrophysics Data System (ADS)

    Glotch, Timothy D.; Bandfield, Joshua L.; Wolff, Michael J.; Arnold, Jessica A.; Che, Congcong

    2016-03-01

    Chloride salt-bearing deposits on Mars were discovered using the Mars Odyssey Thermal Emission Imaging System (THEMIS) and have been characterized by both mid-infrared (MIR) and visible-to-near-infrared (VNIR) remote sensing instruments. The chloride salt-bearing deposits exhibit a blue slope at MIR wavelengths and a featureless red slope at VNIR wavelengths. These deposits also lack strong 3 µm bands in VNIR spectra, indicating that they are desiccated compared to the surrounding regolith. The lack of VNIR spectral features suggests that an anhydrous chloride salt, the most likely of which is halite, is responsible for the observed spectral slope. In this work, we use laboratory spectra and a hybrid T-matrix/Hapke light scattering model to constrain the particle sizes and salt abundances of the Martian chloride salt-bearing deposits. Our work shows that the two broad spectral classes of these deposits observed by THEMIS can be explained by a difference in the particle size of the admixed silicate regolith. In all cases, chloride salt abundances of 10-25% are required to match the THEMIS data. The chloride salt abundances determined in this work suggest deposition in a lacustrine/playa setting or in association with late-stage groundwater upwelling.

  8. Salts in southern Yakutian kimberlites and the problem of primary alkali kimberlite melts

    NASA Astrophysics Data System (ADS)

    Kopylova, M. G.; Kostrovitsky, S. I.; Egorov, K. N.

    2013-04-01

    Alkali carbonates, sodalite, gypsum, anhydrite, halite and sylvite are present in the groundmass and matrix of many kimberlites in the southern part of the Yakutian kimberlite province. The kimberlites were emplaced through 2 km-thick evaporite-bearing carbonate sediments saturated with brines. In the global context, southern Yakutian kimberlites are unprecedented in the amount of the crustal carbonate and evaporite material included in the pipes, as evidenced by the bulk major element chemistry and isotopic compositions of Sr, C, O, Cl and S. We present geological and hydrogeological data on country rocks and kimberlites of the Udachnaya, Mir and International'naya pipes. The secondary, crustal origin of Na, K, Cl and S-rich minerals is supported by the following: 1. A regional correlation between the geology and hydrogeology of the local country rocks and the kimberlite mineralogy, in particular the difference between southern and northern Yakutian kimberlites; 2. A restriction of halite or gypsum mineralization in the Mir and International'naya pipes to depths where pipes intersect country rock strata with similar mineralogy; 3. The localization of the highest abundances of Nasbnd Ksbnd Clsbnd S-bearing minerals in the Udachnaya East kimberlite at a depth interval that correlates across three magmatic phases of kimberlites and coincides with the roof of the halite-bearing country rock and an aquifer carrying anomalously Na-rich brines; 4. The presence of evaporite xenoliths and veins of halite, gypsum and carbonate cutting through the kimberlite and xenoliths; 5. A secondary origin of halite and alkali carbonates as observed in their textural relationships to serpentine and other groundmass minerals; 6. The geochemical and isotopic evidence for crustal contamination. Addition of crustal salts to kimberlite melt began prior to the volcanic fragmentation as a result of preferential melting and assimilation of evaporite xenoliths and may have continued in

  9. Physicochemical changes in dry-cured hams salted with potassium, calcium and magnesium chloride as a partial replacement for sodium chloride.

    PubMed

    Aliño, M; Grau, R; Toldrá, F; Barat, J M

    2010-10-01

    The reduction of added sodium chloride in dry-cured ham has been proposed to reduce dietary sodium intake in Mediterranean countries. The effect of substituting sodium chloride with potassium chloride, calcium chloride and magnesium chloride on some physicochemical characteristics of dry-cured ham during processing was evaluated. The results showed that hams salted with a mixture of sodium and potassium chloride registered higher salt concentrations and lower water contents and thus, needed less time to reach the required weight loss at the end of the process. The opposite effect was observed when calcium and magnesium chloride were added to the salt mixture. The observed differences in the texture and colour parameters were mainly due to differences in water and salt content.

  10. Coordination effect-regulated CO2 capture with an alkali metal onium salts/crown ether system

    SciTech Connect

    Yang, Zhen-Zhen; Jiang, Deen; Zhu, Xiang; Tian, Chengcheng; Brown, Suree; Do-Thanh, Chi-Linh; He, Liang-Nian; Dai, Sheng

    2014-01-01

    A coordination effect was employed to realize equimolar CO2 absorption, adopting easily synthesized amino group containing absorbents (alkali metal onium salts). The essence of our strategy was to increase the steric hindrance of cations so as to enhance a carbamic acid pathway for CO2 capture. Our easily synthesized alkali metal amino acid salts or phenolates were coordinated with crown ethers, in which highly sterically hindered cations were obtained through a strong coordination effect of crown ethers with alkali metal cations. For example, a CO2 capacity of 0.99 was attained by potassium prolinate/18-crown-6, being characterized by NMR, FT-IR, and quantum chemistry calculations to go through a carbamic acid formation pathway. The captured CO2 can be stripped under very mild conditions (50 degrees C, N-2). Thus, this protocol offers an alternative for the development of technological innovation towards efficient and low energy processes for carbon capture and sequestration.

  11. GmCLC1 Confers Enhanced Salt Tolerance through Regulating Chloride Accumulation in Soybean

    PubMed Central

    Wei, Peipei; Wang, Longchao; Liu, Ailin; Yu, Bingjun; Lam, Hon-Ming

    2016-01-01

    The family of chloride channel proteins that mediate Cl- transportation play vital roles in plant nutrient supply, cellular action potential and turgor pressure adjustment, stomatal movement, hormone signal recognition and transduction, Cl- homeostasis, and abiotic and biotic stress tolerance. The anionic toxicity, mainly caused by chloride ions (Cl-), on plants under salt stress remains poorly understood. In this work, we investigated the function of soybean Cl-/H+ antiporter GmCLC1 under salt stress in transgenic Arabidopsis thaliana, soybean, and yeast. We found that GmCLC1 enhanced salt tolerance in transgenic A. thaliana by reducing the Cl- accumulation in shoots and hence released the negative impact of salt stress on plant growth. Overexpression of GmCLC1 in the hairy roots of soybean sequestered more Cl- in their roots and transferred less Cl- to their shoots, leading to lower relative electrolyte leakage values in the roots and leaves. When either the soybean GmCLC1 or the yeast chloride transporter gene, GEF1, was transformed into the yeast gef1 mutant, and then treated with different chloride salts (MnCl2, KCl, NaCl), enhanced survival rate was observed. The result indicates that GmCLC1 and GEF1 exerted similar effects on alleviating the stress of diverse chloride salts on the yeast gef1 mutant. Together, this work suggests a protective function of GmCLC1 under Cl- stress. PMID:27504114

  12. Simultaneous flow-injection measurement of hydroxide, chloride, hypochlorite and chlorate in Chlor-alkali cell effluents.

    PubMed

    Tian, K; Dasgupta, P K

    2000-07-31

    A flow injection method is reported for the simultaneous determination of hydroxide, chloride, hypochlorite, and chlorate ions that exist in Chlor-alkali cell effluents in concentrations ranging from sub-millimolar to several molar. The hydroxide concentration is determined by the heat of neutralization of the injected sample into an acidic carrier stream and the chloride concentration is calculated from the measured conductance data. For the measurement of hypochlorite and chlorate, colorimetric iodometry is used. Iodide is oxidized to iodine by OCl(-) and ClO(3)(-) in acid solutions. While room temperature is sufficient for the reaction between OCl(-) and I(-), the reaction between ClO(3)(-) and I(-) requires an elevated temperature. The different reaction requirements are utilized to differentiate between NaOCl and NaClO(3), respectively.

  13. Corrosion resistance of stainless steels during thermal cycling in alkali nitrate molten salts.

    SciTech Connect

    Bradshaw, Robert W.; Goods, Steven Howard

    2001-09-01

    The corrosion behavior of three austenitic stainless steels was evaluated during thermal cycling in molten salt mixtures consisting of NaNO{sub 3} and KNO{sub 3}. Corrosion tests were conducted with Types 316, 316L and 304 stainless steels for more than 4000 hours and 500 thermal cycles at a maximum temperature of 565 C. Corrosion rates were determined by chemically descaling coupons. Metal losses ranged from 5 to 16 microns and thermal cycling resulted in moderately higher corrosion rates compared to isothermal conditions. Type 316 SS was somewhat more corrosion resistant than Type 304 SS in these tests. The effect of carbon content on corrosion resistance was small, as 316L SS corroded only slightly slower than 316 SS. The corrosion rates increased as the dissolved chloride content of the molten salt mixtures increased. Chloride concentrations approximating 1 wt.%, coupled with thermal cycling, resulted in linear weight loss kinetics, rather than parabolic kinetics, which described corrosion rates for all other conditions. Optical microscopy and electron microprobe analysis revealed that the corrosion products consisted of iron-chromium spinel, magnetite, and sodium ferrite, organized as separate layers. Microanalysis of the elemental composition of the corrosion products further demonstrated that the chromium content of the iron-chromium spinel layer was relatively high for conditions in which parabolic kinetics were observed. However, linear kinetics were observed when the spinel layer contained relatively little chromium.

  14. Salt equivalence and temporal dominance of sensations of different sodium chloride substitutes in butter.

    PubMed

    de Souza, Vanessa Rios; Freire, Tassyana Vieira Marques; Saraiva, Carla Gonçalves; de Deus Souza Carneiro, João; Pinheiro, Ana Carla Marques; Nunes, Cleiton Antônio

    2013-08-01

    Studies indicate a positive association between dietary salt intake and some diseases, which has promoted the tendency to reduce the sodium in foods. The objective of this study was to determine the equivalent amount of different sodium chloride replacements required to promote the same degree of ideal saltiness in butter and to study the sensory profile of sodium chloride and the substitutes using the analysis of Temporal Dominance of Sensations (TDS). Using the magnitude estimation method, it was determined that the potencies of potassium chloride, monosodium glutamate and potassium phosphate relative to the 1% sodium chloride in butter are 83·33, 31·59 and 33·32, respectively. Regarding the sensory profile of the tested salt substitutes, a bitter taste was perceived in the butter with potassium chloride, a sour taste was perceived in the butter with potassium phosphate and sweet and umami tastes were dominant in the butter with monosodium glutamate. Of all the salt substitutes tested calcium lactate, potassium lactate, calcium chloride and magnesium chloride were impractical to use in butter.

  15. Effects of sodium chloride salting and substitution with potassium chloride on whey expulsion of Cheddar cheese.

    PubMed

    Lu, Y; McMahon, D J

    2015-01-01

    A challenge in manufacturing reduced-sodium cheese is that whey expulsion after salting decreases when less salt is applied. Our objectives were (1) to determine whether changing the salting method would increase whey syneresis when making a lower sodium cheese and (2) to better understand factors contributing to salt-induced curd syneresis. Unsalted milled Cheddar curds were salted using different salting intervals (5 or 10 min), different salting levels (20, 25, or 30g/kg), different numbers of applications when using only 20g/kg salt (1, 2, or 3 applications), and salting with the equivalent of 30g/kg NaCl using a 2:1 molar ratio of NaCl and KCl. Whey from these curds was collected every 5 or 10 min until 30 or 40 min after the start of salting, and curds were subsequently pressed for 3h. Additional trials were conducted in which salted milled Cheddar cheese curd was immersed at 22°C for 6h in various solutions to determine how milled curd pieces respond to different levels of salt and Ca. The use of 10-min intervals delayed whey syneresis without influencing total whey expulsion or cheese composition after pressing. Lowering the salt level reduced whey expulsion, resulting in cheeses with higher moisture and slightly lower pH. Adding salt faster did not increase whey expulsion in reduced-salt cheese. Partial substitution with KCl restored the extent of whey expulsion. When salted milled curd was immersed in a 30g/L salt solution, there was a net influx of salt solution into the curd and curd weight increased. When curd was immersed in 60g/L salt solution, a contraction of curd occurred. Curd shrinkage was more pronounced as the salt solution concentration was increased to 90 and 120g/L. Increasing the Ca concentration in test solutions (such that both serum and total Ca in the curd increased) also promoted curd contraction, resulting in lower curd moisture and pH and less weight gain by the curd. The proportion of Ca in the curd that was bound to the para

  16. Anion effect on selectivity in solvent extraction of alkali metal salts by crown ethers

    SciTech Connect

    Hankins, M.G.; Bartsch, R.A.; Olsher, U.

    1995-11-01

    The influence of the co-extracted anion upon competitive solvent extraction of five alkali metal cations from aqueous solutions into organic diluents by the cis-syn-cis and cis-anti-cis isomers of dicyclohexano-18-crown-6 has been assessed. The anions are bromide, chloride, iodide, nitrate, perchlorate, and thiocyanate and the organic diluents are chloroform and 1-octanol. The extraction efficiency is markedly influenced by the identity of the anion and exhibits some correlation with the inverse of the hydration enthalpy of the anion. Although potassium is the best exctracted cation with all anions, the selectivities for potassium over lithium, sodium, rubidium, and cesium are strongly affected by anion variation in chloroform, but not in 1-octanol. The selectivity ordering in chloroform does not correlate with the hydration enthalpy or softness parameter for the anion. Instead it appears to result from variation of the dimensional structure and the availability of specific binding sites in the anion. 21 refs., 1 fig., 5 tabs.

  17. Effect of chloride content of molten nitrate salt on corrosion of A516 carbon steel.

    SciTech Connect

    Bradshaw, Robert W.; Clift, W. Miles

    2010-11-01

    The corrosion behavior of A516 carbon steel was evaluated to determine the effect of the dissolved chloride content in molten binary Solar Salt. Corrosion tests were conducted in a molten salt consisting of a 60-40 weight ratio of NaNO{sub 3} and KNO{sub 3} at 400{sup o}C and 450{sup o}C for up to 800 hours. Chloride concentrations of 0, 0.5 and 1.0 wt.% were investigated to determine the effect on corrosion of this impurity, which can be present in comparable amounts in commercial grades of the constituent salts. Corrosion rates were determined by descaled weight losses, corrosion morphology was examined by metallographic sectioning, and the types of corrosion products were determined by x-ray diffraction. Corrosion proceeded by uniform surface scaling and no pitting or intergranular corrosion was observed. Corrosion rates increased significantly as the concentration of dissolved chloride in the molten salt increased. The adherence of surface scales, and thus their protective properties, was degraded by dissolved chloride, fostering more rapid corrosion. Magnetite was the only corrosion product formed on the carbon steel specimens, regardless of chloride content or temperature.

  18. Metal-free Synthesis of Ynones from Acyl Chlorides and Potassium Alkynyltrifluoroborate Salts

    PubMed Central

    Taylor, Cassandra L.; Bolshan, Yuri

    2015-01-01

    Ynones are a valuable functional group and building block in organic synthesis. Ynones serve as a precursor to many important organic functional groups and scaffolds. Traditional methods for the preparation of ynones are associated with drawbacks including harsh conditions, multiple purification steps, and the presence of unwanted byproducts. An alternative method for the straightforward preparation of ynones from acyl chlorides and potassium alkynyltrifluoroborate salts is described herein. The adoption of organotrifluoroborate salts as an alternative to organometallic reagents for the formation of new carbon-carbon bonds has a number of advantages. Potassium organotrifluoroborate salts are shelf stable, have good functional group tolerance, low toxicity, and a wide variety are straightforward to prepare. The title reaction proceeds rapidly at ambient temperature in the presence of a Lewis acid without the exclusion of air and moisture. Fair to excellent yields may be obtained via reaction of various aryl and alkyl acid chlorides with alkynyltrifluoroborate salts in the presence of boron trichloride. PMID:25742169

  19. ION EXCHANGE IN FUSED SALTS. II. THE DISTRIBUTION OF ALKALI METAL AND ALKALINE EARTH IONS BETWEEN CHABAZITE AND FUSED LINO3, NANO3, AND KNO3,

    DTIC Science & Technology

    ION EXCHANGE, SALTS ), (*ALKALI METALS, ION EXCHANGE), (*ALKALINE EARTH METALS, ION EXCHANGE), (*NITRATES, ION EXCHANGE), SODIUM , CALCIUM, POTASSIUM...BARIUM, RUBIDIUM, CESIUM, LITHIUM COMPOUNDS, SODIUM COMPOUNDS, POTASSIUM COMPOUNDS, DISTRIBUTION, MINERALS, IONS

  20. Method for making a uranium chloride salt product

    DOEpatents

    Miller, William E.; Tomczuk, Zygmunt

    2004-10-05

    The subject apparatus provides a means to produce UCl.sub.3 in large quantities without incurring corrosion of the containment vessel or associated apparatus. Gaseous Cl is injected into a lower layer of Cd where CdCl.sub.2 is formed. Due to is lower density, the CdCl.sub.2 rises through the Cd layer into a layer of molten LiCl--KCL salt where a rotatable basket containing uranium ingots is suspended. The CdCl.sub.2 reacts with the uranium to form UCl.sub.3 and Cd. Due to density differences, the Cd sinks down to the liquid Cd layer and is reused. The UCl.sub.3 combines with the molten salt. During production the temperature is maintained at about 600.degree. C. while after the uranium has been depleted the salt temperature is lowered, the molten salt is pressure siphoned from the vessel, and the salt product LiCl--KCl-30 mol % UCl.sub.3 is solidified.

  1. Alkali Metal Halide Salts as Interface Additives to Fabricate Hysteresis-Free Hybrid Perovskite-Based Photovoltaic Devices.

    PubMed

    Wang, Lili; Moghe, Dhanashree; Hafezian, Soroush; Chen, Pei; Young, Margaret; Elinski, Mark; Martinu, Ludvik; Kéna-Cohen, Stéphane; Lunt, Richard R

    2016-09-07

    A new method was developed for doping and fabricating hysteresis-free hybrid perovskite-based photovoltaic devices by using alkali metal halide salts as interface layer additives. Such salt layers introduced at the perovskite interface can provide excessive halide ions to fill vacancies formed during the deposition and annealing process. A range of solution-processed halide salts were investigated. The highest performance of methylammonium lead mixed-halide perovskite device was achieved with a NaI interlayer and showed a power conversion efficiency of 12.6% and a hysteresis of less than 2%. This represents a 90% improvement compared to control devices without this salt layer. Through depth-resolved mass spectrometry, optical modeling, and photoluminescence spectroscopy, this enhancement is attributed to the reduction of iodide vacancies, passivation of grain boundaries, and improved hole extraction. Our approach ultimately provides an alternative and facile route to high-performance and hysteresis-free perovskite solar cells.

  2. LOCALIZED CORROSION OF AUSTENITIC STAINLESS STEELEXPOSED TO MIXTURES OF PLUTONIUM OXIDE AND CHLORIDE SALTS

    SciTech Connect

    Zapp, P; Kerry Dunn, K; Jonathan Duffey, J; Ron Livingston, R; Zane Nelson, Z

    2008-11-21

    Laboratory corrosion tests were conducted to investigate the corrosivity of moist plutonium oxide/chloride (PuO{sub 2}/Cl-) salt mixtures on 304L and 316L stainless steel coupons. The tests exposed flat coupons for pitting evaluation and 'teardrop' stressed coupons for stress corrosion cracking (SCC) evaluation at room temperature to various mixtures of PuO{sub 2} and chloride-bearing salts for periods up to 500 days. The two flat coupons were placed so that the solid oxide/salt mixture contacted about one half of the coupon surface. One teardrop coupon was placed in contact with solid mixture; the second teardrop was in contact with the headspace gas only. The mixtures were loaded with nominally 0.5 wt % water under a helium atmosphere. Observations of corrosion ranged from superficial staining to pitting and SCC. The extent of corrosion depended on the total salt concentration and on the composition of the salt. The most significant corrosion was found in coupons that were exposed to 98 wt % PuO{sub 2}, 2 wt % chloride salt mixtures that contained calcium chloride. SCC was observed in two 304L stainless steel teardrop coupons exposed in solid contact to a mixture of 98 wt % PuO{sub 2}, 0.9 wt % NaCl, 0.9 wt % KCl, and 0.2 wt % CaCl{sub 2}. The cracking was associated with the heat-affected zone of an autogenous weld that ran across the center of the coupon. Cracking was not observed in coupons exposed to the headspace gas, nor in coupons exposed to other mixtures with either 0.92 wt% CaCl{sub 2} or no CaCl{sub 2}. The corrosion results point to the significance of the interaction between water loading and the concentration of the hydrating salt CaCl{sub 2} in the susceptibility of austenitic stainless steels to corrosion.

  3. Chloride Released from Three Permeable Pavement Surfaces after Winter Salt Application

    EPA Science Inventory

    EPA does not classify chloride as a priority pollutant. It is often unregulated in stormwater runoff but has been a target stressor for Total Maximum Daily Load (TMDL) allotments developed for multiple waterbodies. Previous research has shown that road salt applications increas...

  4. Chloride Released from Three Permeable Pavement Surfaces after Winter Salt Application - journal

    EPA Science Inventory

    EPA does not classify chloride as a priority pollutant. It is often unregulated in stormwater runoff but has been a target stressor for Total Maximum Daily Load (TMDL) allotments developed for multiple waterbodies. Previous research has shown that road salt applications increas...

  5. The borosulfate story goes on--from alkali and oxonium salts to polyacids.

    PubMed

    Daub, Michael; Kazmierczak, Karolina; Höppe, Henning A; Hillebrecht, Harald

    2013-12-09

    The structural principles of borosulfates derived from the B/S ratio are confirmed and extended to new representatives of this class showing novel motifs. According to the composition, Na[B(S2O7)2] (P2(1)/c; a=10.949(6), b=8.491(14), c=12.701(8) Å; β=110.227(1)°; Z=4) and K[B(S2O7)2] (Cc; a=11.3368(6), b=14.662(14), c=13.6650(8) Å; β=94.235(1)°; Z=8) contain isolated [B(S2O7)2](-) ions, in which the central BO4 tetrahedron is coordinated by two disulfate units. The alkali cations have coordination numbers of 7 (Na) and 8 (K), respectively. The structure of Cs[B(S2O7)(SO4)] (P2(1)/c; a=10.4525(6), b=11.3191(14), c=8.2760(8) Å; β=103.206(1); Z=4) combines, for the first time, sulfate and disulfate units into a chain structure. Cs has a coordination number of 12. The same structural units were found in H[B(S2O7)(SO4)] (P2(1)/c; a=15.6974(6), b=11.4362(14), c=8.5557(8) Å; β=90.334(3)°; Z=8). This compound represents the first example of a polyacid. The hydrogen atoms were located and connect the chains to form layers through hydrogen-bonding bridges. H3O[B(SO4)2] (P4/ncc; a=9.1377(6), c=7.3423(8) Å; Z=4) is the first oxonium compound of this type to be found. The BO4 tetrahedra are linked by SO4 tetrahedra to form linear chains similar to those in SiS2. The chains form a tetragonal rod packing structure with H3O(+) between the rods. The structures of borosulfates can be classified following the concept described by Liebau for silicates, which was extended to borophosphates by Kniep et al. In contrast to these structures, borosulfates do not comprise B-O-B bonds but instead contain S-O-S connections. All compounds were obtained as colourless, moisture-sensitive single crystals by reaction of B2O3 and the appropriate alkali salt in oleum.

  6. Detailed spectroscopic analysis of chloride salt deposits in Terra Sirenum, Mars

    NASA Astrophysics Data System (ADS)

    Osterloo, M. M.; Glotch, T. D.; Bandfield, J. L.

    2015-12-01

    Chloride salt-bearing deposits have been identified throughout the southern highlands of Mars [1] based on the lack of diagnostic spectral features of anhydrous chlorides in both the visible near infrared (VNIR) and middle infrared (MIR) wavelength ranges [1,2]. A puzzling aspect of martian chloride deposits is the apparent lack of other weathering or evaporite phases associated with most of the deposits. A global analysis over the chloride salt sites conducted by [3] found that only ~9% of the deposits they analyzed were associated with minerals such as phyllosilicates. Most of these occurrences are in Terra Sirenum where [4] noted that salt-bearing deposits lie stratigraphically above Noachian phyllosilicates. Although a variety of formation mechanisms have been proposed for these intriguing deposits, detailed geologic mapping by [5] suggests that surface water and evaporation played a dominant role. On Earth, evaporative settings are often characterized by a multitude of evaporite and phyllosilicate phases including carbonates, sulfates, and nitrates. [6] evaluated chemical divides and brine evolution for martian systems and their results indicate three pathways wherein late-stage brines favor chloride precipitation. In each case the pathway to chloride formation includes precipitation of carbonates (calcite, siderite, and/or magnesite) and sulfates (gypsum, melanterite, and/or epsomite). Here, we present the results of our detailed and systematic spectroscopic study to identify additional evaporite phases associated with salt/silicate mixtures in Terra Sirenum. [1] Osterloo et al. (2008) Science, 319, [2] Glotch, T. D. et al. (2013) Lunar and Planet. Sci. XLIV, abstract #1549 [3] Ruesch, O. et al. (2012), J. Geophys. Res., 117, E00J13 [4] Glotch, T. D. et al. (2010) Geophys. Res. Lett. 37, L16202, [5] Osterloo, M. M. and B. M Hynek (2015) Lunar and Planet. Sci XLVI. Abstract #1054 [6] Tosca, N. J. and S. M. McLennan (2006), Earth and Planet. Sci. Lett., 241.

  7. Groundwater chloride response in the Highland Creek watershed due to road salt application: A re-assessment after 20 years

    NASA Astrophysics Data System (ADS)

    Perera, Nandana; Gharabaghi, Bahram; Howard, Ken

    2013-02-01

    SummaryChloride from road salt enters streams primarily through surface runoff and groundwater discharge. Monitoring of dry-weather flow chloride concentrations in the Highland Creek watershed of the eastern Greater Toronto Area indicates the presence of a previously unrecognised, dual porosity aquifer system whereby preferential flow associated with "urban karst" exerts a significant influence on baseflow chloride concentrations early in the year. A chloride mass balance undertaken annually over four successive salting seasons suggests that as much as 40% of the chloride applied as road salt enters the shallow aquifer resulting in a net accumulation of chloride and a gradual increase in mean baseflow chloride concentrations. Assuming current road salt application rates are continued, late summer baseflow chloride concentrations will reach around 505 mg/L, almost double present levels. Elevated chloride concentrations can affect the potability of water (the Canadian aesthetic drinking water quality guideline for chloride is 250 mg/L) and can also be toxic to aquatic organisms (CCME aquatic chronic toxicity guideline is 208 mg/L). Meeting these guidelines would require that the release of salt-laden runoff to the subsurface be reduced by over 50%.

  8. Wearable Potentiometric Chloride Sweat Sensor: The Critical Role of the Salt Bridge.

    PubMed

    Choi, Dong-Hoon; Kim, Jin Seob; Cutting, Garry R; Searson, Peter C

    2016-12-20

    The components of sweat provide an array of potential biomarkers for health and disease. Sweat chloride is of interest as a biomarker for cystic fibrosis, electrolyte metabolism disorders, electrolyte balance, and electrolyte loss during exercise. Developing wearable sensors for biomarkers in sweat is a major technological challenge. Potentiometric sensors provide a relatively simple technology for on-body sweat chloride measurement, however, equilibration between reference and test solutions has limited the time over which accurate measurements can be made. Here, we report on a wearable potentiometric chloride sweat sensor. We performed parametric studies to show how the salt bridge geometry determines equilibration between the reference and test solutions. From these results, we show a sweat chloride sensor can be designed to provide accurate measurements over extended times. We then performed on-body tests on healthy subjects while exercising to establish the feasibility of using this technology as a wearable device.

  9. Highly Effective Pt-Based Water-Gas Shift Catalysts by Surface Modification with Alkali Hydroxide Salts

    SciTech Connect

    Kusche, Matthias; Bustillo, Karen; Agel, Friederike; Wasserscheid, Peter

    2015-01-29

    Here, we describe an economical and convenient method to improve the performance of Pt/alumina catalysts for the water–gas shift reaction through surface modification of the catalysts with alkali hydroxides according to the solid catalyst with ionic liquid layer approach. The results are in agreement with our findings reported earlier for methanol steam reforming. This report indicates that alkali doping of the catalyst plays an important role in the observed catalyst activation. In addition, the basic and hygroscopic nature of the salt coating contributes to a significant improvement in the performance of the catalyst. During the reaction, a partly liquid film of alkali hydroxide forms on the alumina surface, which increases the availability of H2O at the catalytically active sites. Kinetic studies reveal a negligible effect of the KOH coating on the rate dependence of CO and H2O partial pressures. In conclusion, TEM studies indicate an agglomeration of the active Pt clusters during catalyst preparation; restructuring of Pt nanoparticles occurs under reaction conditions, which leads to a highly active and stable system over 240h time on stream. Excessive pore fillings with KOH introduce a mass transfer barrier as indicated in a volcano-shaped curve of activity versus salt loading. The optimum KOH loading was found to be 7.5wt%.

  10. Highly Effective Pt-Based Water-Gas Shift Catalysts by Surface Modification with Alkali Hydroxide Salts

    DOE PAGES

    Kusche, Matthias; Bustillo, Karen; Agel, Friederike; ...

    2015-01-29

    Here, we describe an economical and convenient method to improve the performance of Pt/alumina catalysts for the water–gas shift reaction through surface modification of the catalysts with alkali hydroxides according to the solid catalyst with ionic liquid layer approach. The results are in agreement with our findings reported earlier for methanol steam reforming. This report indicates that alkali doping of the catalyst plays an important role in the observed catalyst activation. In addition, the basic and hygroscopic nature of the salt coating contributes to a significant improvement in the performance of the catalyst. During the reaction, a partly liquid filmmore » of alkali hydroxide forms on the alumina surface, which increases the availability of H2O at the catalytically active sites. Kinetic studies reveal a negligible effect of the KOH coating on the rate dependence of CO and H2O partial pressures. In conclusion, TEM studies indicate an agglomeration of the active Pt clusters during catalyst preparation; restructuring of Pt nanoparticles occurs under reaction conditions, which leads to a highly active and stable system over 240h time on stream. Excessive pore fillings with KOH introduce a mass transfer barrier as indicated in a volcano-shaped curve of activity versus salt loading. The optimum KOH loading was found to be 7.5wt%.« less

  11. Microwave irradiation affects ion pairing in aqueous solutions of alkali halide salts

    NASA Astrophysics Data System (ADS)

    Mohorič, Tomaž; Bren, Urban

    2017-01-01

    Using the molecular dynamics simulations with separate thermostats for translational and rotational degrees of freedom, we investigate the effects of water's rotational motion on the ion pairing of ionic solutes in aqueous solutions. The situation with rotational temperature higher than the translational one, Trot>Ttrs , is mimicking the non-equilibrium effects of microwaves on model solutions of alkali halide salts. The simulations reveal that an increase in the rotational temperature at constant translational temperature exerts significant changes in the structure of the solution. The latter are reflected in increased pairing of the oppositely charged ions, which can be explained by the weaker ability of rotationally excited water to screen and separate the opposite charges. It seems that Collins' law of matching water affinities retains its validity also in the non-equilibrium situation where the rotational temperature exceeds the translational one. On the other hand, the equilibrium effect (i.e., an increase in the solution's overall temperature T ≡Trot = Ttrs) favors the formation of small-small (NaCl), while it has a little effect on large-large (CsI) ion pairs. This is in accordance with water becoming less polar solvent upon a temperature increase. Furthermore, we investigated the effects of excited translational motion of water (and ions) on the ion pairing by increasing the translational temperature, while keeping the rotational one unchanged (i.e., Ttrs>Trot ). Interestingly, in certain cases the faster translational motion causes an increase in correlations. The temperature variations in the like-ion association constants, Kas++ and Kas-, are also examined. Here the situation is more complex but, in most cases, a decrease in the ion pairing is observed.

  12. Alkali metal salts of rutin - Synthesis, spectroscopic (FT-IR, FT-Raman, UV-VIS), antioxidant and antimicrobial studies.

    PubMed

    Samsonowicz, M; Kamińska, I; Kalinowska, M; Lewandowski, W

    2015-12-05

    In this work several metal salts of rutin with lithium, sodium, potassium, rubidium and cesium were synthesized. Their molecular structures were discussed on the basis of spectroscopic (FT-IR, FT-Raman, UV-VIS) studies. Optimized geometrical structure of rutin was calculated by B3LYP/6-311++G(∗∗) method and sodium salt of rutin were calculated by B3LYP/LanL2DZ method. Metal chelation change the biological properties of ligand therefore the antioxidant (FRAP and DPPH) and antimicrobial activities (toward Escherichia coli, Staphylococcus aureus, Enterococcus faecium, Proteus vulgaris, Pseudomonas aeruginosa, Klebsiella pneumonia, Candida albicans and Saccharomyces cerevisiae) of alkali metal salts were evaluated and compared with the biological properties of rutin.

  13. Hydrogeologic Processes Impacting Storage, Fate, and Transport of Chloride from Road Salt in Urban Riparian Aquifers.

    PubMed

    Ledford, Sarah H; Lautz, Laura K; Stella, John C

    2016-05-17

    Detrimental effects of road salt runoff on urban streams are compounded by its facilitated routing via storm drains, ditches, and flood channels. Elevated in-stream salinity may also result from seasonal storage and discharge of chloride in groundwater, and previous work has hypothesized that groundwater discharge to streams may have the effect of diluting stream chloride concentrations in winter and enriching them in summer. However, the hydrogeological processes controlling these patterns have not been thoroughly investigated. Our research focuses on an urban stream and floodplain system in Syracuse, NY, to understand how groundwater and surface water exchange impacts chloride storage, fate, and transport. We created a 3D groundwater flow and solute transport model of the floodplain, calibrated to the distributions of floodplain hydraulic heads and groundwater fluxes to the stream throughout the reach. We used a sensitivity analysis to calibrate and evaluate the influence of model parameters, and compared model outputs to field observations. The main source mechanism of chloride to the floodplain aquifer was high-concentration, overbank flood events in winter that directly recharged groundwater. The modeled residence time and storage capacity of the aquifer indicate that restoration projects designed to promote floodplain reconnection and the frequency of overbank flooding in winter have the potential to temporarily store chloride in groundwater, buffer surface water concentrations, and reduce stream concentrations following periods of road salting.

  14. Chloride salt mixtures affect Gordal cv. green Spanish-style table olive fermentation.

    PubMed

    Bautista Gallego, J; Arroyo López, F N; Romero Gil, V; Rodríguez Gómez, F; García García, P; Garrido Fernández, A

    2011-10-01

    This work studies the effects of different sodium (in the range of 4-10%), potassium (0-4%) and calcium (0-6%) chloride salt mixtures on the fermentation profile of Gordal olives processed according to the Spanish style. For this purpose, response surface methodology based on a simplex centroid mixture design with constrain (sum of salt percentages = 10%) was used. All treatments reached appropriate titratable acidity levels, but this parameter could not be related to the initial chloride salt concentration. The presence of CaCl(2) led to lower initial and after-fermentation pHs, delayed sugar diffusion into the brine, its maximum concentration and titratable acidity formation. CaCl(2) also delayed Enterobacteriaceae and yeast sprang, decreasing their overall growth. This chloride salt also showed a tendency to reduce overall lactic acid bacteria growth. KCl had a similar behaviour to NaCl but, in general, increased overall microbial growth. Thus, a partial substitution of NaCl in Spanish-style green olives with KCl and CaCl(2) does not substantially modify the fermentation profile but does produce some changes, which, when properly managed, could help to improve product processing.

  15. Iron(III)-induced activation of chloride and bromide from modeled salt pans.

    PubMed

    Wittmer, Julian; Bleicher, Sergej; Zetzsch, Cornelius

    2015-05-14

    The photochemistry of halides in sea spray aerosol, on salt pans, and on other salty surfaces leads to a formation of reactive halogen species. We investigated the photochemical formation of atomic chlorine (Cl) and bromine (Br) in the gas phase in the presence of laboratory-modeled salt pans consisting of sodium chloride doped with iron(III) chloride hexahydrate (0.5 and 2 wt %). The samples were spread on a Teflon sheet and exposed to simulated sunlight in a Teflon smog chamber in purified, humidified air in the presence of a test mixture of hydrocarbons at the ppb level to determine Cl, Br, and OH formation by the radical clock method. Driven by the photolytic reduction of Fe(III) to Fe(II), the production rates of the Fe(III)-doped NaCl salt samples (up to10(7) atoms cm(-3) s(-1)) exceeded the release of Cl above a pure NaCl sample by more than an order of magnitude in an initially O3-free environment at low NOX. In bromide-doped samples (0.5 wt % NaBr), a part of the Cl release was replaced by Br when Fe(III) was present. Additions of sodium sulfate, sodium oxalate, oxalic acid, and catechol to NaCl/FeCl3 samples were found to restrain the activation of chloride.

  16. Fourteen-year survival of Pseudomonas cepacia in a salts solution preserved with benzalkonium chloride.

    PubMed Central

    Geftic, S G; Heymann, H; Adair, F W

    1979-01-01

    A strain of Pseudomonas cepacia that survived for 14 years (1963 to 1977) as a contaminant in an inorganic salt solution which contained commercial 0.05% benzalkonium chloride (CBC) as an antimicrobial preservative, was compared to a recent clinical isolate of P. cepacia. Ammonium acetate was present in the concentrated stock CBC solution, and served as a carbon and nitrogen source for growth when carried over into the salts solution with the CBC. The isolate's resistance to pure benzalkonium chloride was increased step-wise to a concentration of 16%. Plate counts showed 4 x 10(3) colony-forming units per ml in the salts solution. Comparison of growth rates, mouse virulence, antibiotics resistance spectra, and substrate requirements disclosed no differences between the contaminant and a recently isolated clinical strain of P. cepacia. The results indicate that it is critical that pharmaceutical solutions containing benzalkonium chloride as an antimicrobial preservative be formulated without extraneous carbon and nitrogen sources or be preserved with additional antimicrobial agents. PMID:453827

  17. Methanol synthesis using a catalyst combination of alkali or alkaline earth salts and reduced copper chromite for methanol synthesis

    DOEpatents

    Tierney, John W.; Wender, Irving; Palekar, Vishwesh M.

    1993-01-01

    The present invention relates to a novel route for the synthesis of methanol, and more specifically to the production of methanol by contacting synthesis gas under relatively mild conditions in a slurry phase with a catalyst combination comprising reduced copper chromite and basic alkali salts or alkaline earth salts. The present invention allows the synthesis of methanol to occur in the temperature range of approximately 100.degree.-160.degree. C. and the pressure range of 40-65 atm. The process produces methanol with up to 90% syngas conversion per pass and up to 95% methanol selectivity. The only major by-product is a small amount of easily separated methyl formate. Very small amounts of water, carbon dioxide and dimethyl ether are also produced. The present catalyst combination also is capable of tolerating fluctuations in the H.sub.2 /CO ratio without major deleterious effect on the reaction rate. Furthermore, carbon dioxide and water are also tolerated without substantial catalyst deactivation.

  18. Phosphorus extraction and sludge dissolution by acid and alkali treatments of polyaluminum chloride (PAC) treated wastewater sludge.

    PubMed

    Ali, Toor Umair; Kim, Dong-Jin

    2016-10-01

    Phosphorus (P) leaching characteristics of polyaluminium chlorides (PAC) treated wastewater sludge was investigated by wet chemicals (acid and alkali). Sludge fractionation showed non-apatite inorganic P was the dominant P (90.9% of TP) while apatite P only accounted for 3.7%. After 2h extraction with 1N NaOH or 2N HCl, 80.5% and 77.9% of total P was leached, while sludge dissolution reached 72.7% and 75.6%, respectively. Kinetic study with HCl and NaOH showed that P release and sludge dissolution follow first order reaction with rate constants of 0.50 and 0.35min(-1) (P release) and 0.47×10(-2) and 0.15×10(-2)min(-1) (sludge dissolution), respectively. Sequential extraction by NaOH/HCl leached 91.7% of the total P. This study will help in understanding the P release behavior of the PAC treated wastewater sludge.

  19. Combined effect of alkali pretreatment and sodium chloride addition on the olive fermentation process.

    PubMed

    Chammem, N; Kachouri, M; Mejri, M; Peres, C; Boudabous, A; Hamdi, M

    2005-07-01

    Green olives of the Tunisian variety "Meski" were treated according to a Spanish-style green olive preservation process by using an alkaline treatment (1.5, 2 and 2.5% (w/v) NaOH) to eliminate bitterness, combined with different brine concentrations (6, 9 and 12% (w/v) NaCl). A spontaneous fermentation by the environmental microflora took place. Results showed that 2% NaOH solution and 9% sodium chloride brine was an optimal combination inducing the best growth of Lactobacillus species (10(8) CFU/ml) and acidity of 0.726 g lactic acid/100 ml brine. In all trials and independently of the treatment, Lb. plantarum was the most dominant strain of Lactobacillus. Moreover, pretreatment with lye and lactic fermentation of olives contributed to coliform elimination.

  20. Use of mulberry-soybean intercropping in salt-alkali soil impacts the diversity of the soil bacterial community.

    PubMed

    Li, Xin; Sun, Minglong; Zhang, Huihui; Xu, Nan; Sun, Guangyu

    2016-05-01

    Diverse intercropping system has been used to control disease and improve productivity in the field. In this research, the bacterial communities in salt-alkali soils of monoculture and intercropping mulberry and soybean were studied using 454-pyrosequencing of the 16S rDNA gene. The dominant taxonomic groups were Proteobacteria, Acidobacteria, Actinobacteria, Chloroflexi, Bacteroidetes, Planctomycetes and Gemmatimonadetes and these were present across all samples. However, the diversity and composition of bacterial communities varied between monoculture and intercropping samples. The estimated bacterial diversity (H') was higher with intercropping soybean than in monoculture soybean, whereas H' showed an opposite pattern in monoculture and intercropping mulberry. Populations of Actinobacteria, Acidobacteria, and Proteobacteria were variable, depending on growth of plants as monoculture or intercropped. Most of Actinobacteria and Chloroflexi were found in intercropping samples, while Acidobacteria and Proteobacteria were present at a higher percentage in monoculture samples. The plant diversity of aboveground and microbial diversity of belowground was linked and soil pH seemed to influence the bacterial community. Finally, the specific plant species was the major factor that determined the bacterial community in the salt-alkali soils.

  1. Origin of salts and alkali carbonates in the Udachnaya East kimberlite: Insights from petrography of kimberlite phases and their carbonate and evaporite xenoliths

    NASA Astrophysics Data System (ADS)

    Kopylova, M. G.; Gaudet, M.; Kostrovitsky, S. I.; Polozov, A. G.; Yakovlev, D. A.

    2016-11-01

    The Udachnaya East kimberlite is characterized by the presence of chlorides, sulfates and alkali carbonates. This highly atypical mineralogy underpinned a model for an anhydrous alkali-rich primary kimberlite melt, despite the absence of petrographic studies providing textural context to the exotic minerals. The present work documents the petrography of the Udachnaya East kimberlite in order to address this problem. The pipe comprises two varieties of Fort-a-la-Corne type pyroclastic kimberlite, olivine-rich and magmaclast-rich, and coherent kimberlite. These kimberlites entrain xenoliths of limestones, altered shales and siltstones, halite-dominated rocks, dolomites, and coarse calcite rocks. The distinct varieties of the Udachnaya East kimberlite carry different populations of crustal xenoliths, which partially control the mineralogy of the host kimberlite. In magmaclast-rich pyroclastic kimberlite, where halite is absent from the crustal xenoliths, it is not observed in the interclast matrix, or within the magmaclasts. Halite occurs in the interclast matrix of olivine-rich pyroclastic kimberlite, where halite xenoliths are common. Large, 30 cm halite xenoliths are uniquely restricted to the coherent kimberlite and show a strong reaction with it. The halite xenoliths are sourced from depths of - 1500 to - 630 m, where carbonate beds host multiple karst cavities filled with halite and gypsum and occasional sedimentary evaporites. The style of secondary mineralization at Udachnaya depends on whether the kimberlite is coherent or pyroclastic. Shortite, pirssonite and other alkali carbonates replacing calcite and possibly serpentine are abundant only in porous pyroclastic kimberlites of both types and in their shale/siltstone xenoliths. The lower porosity of the coherent kimberlite prevented the interaction of kimberlite with Na brines. Serpentinization localized around halite xenoliths started at temperatures above 500 °C, as indicated by its association with high

  2. ROAD SALT APPLICATION CREATES A UNIQUE CHLORIDE BIOCHEMISTRY IN AN URBAN STREAM OF THE CHESAPEAKE BAY WATERSHED

    EPA Science Inventory

    Recent evidence from the mid-Atlantic suggests that freshwater supplies are threatened by chronic chloride inputs from road salts applied to improve highway safety. Elevated chloride levels also may limit the ability of aquatic systems to microbially process nitrate nitrogen, a ...

  3. Using chloride and other ions to trace sewage and road salt in the Illinois Waterway

    USGS Publications Warehouse

    Kelly, W.R.; Panno, S.V.; Hackley, Keith C.; Hwang, H.-H.; Martinsek, A.T.; Markus, M.

    2010-01-01

    Chloride concentrations in waterways of northern USA are increasing at alarming rates and road salt is commonly assumed to be the cause. However, there are additional sources of Cl- in metropolitan areas, such as treated wastewater (TWW) and water conditioning salts, which may be contributing to Cl- loads entering surface waters. In this study, the potential sources of Cl- and Cl- loads in the Illinois River Basin from the Chicago area to the Illinois River's confluence with the Mississippi River were investigated using halide data in stream samples and published Cl- and river discharge data. The investigation showed that road salt runoff and TWW from the Chicago region dominate Cl- loads in the Illinois Waterway, defined as the navigable sections of the Illinois River and two major tributaries in the Chicago region. Treated wastewater discharges at a relatively constant rate throughout the year and is the primary source of Cl- and other elements such as F- and B. Chloride loads are highest in the winter and early spring as a result of road salt runoff which can increase Cl- concentrations by up to several hundred mg/L. Chloride concentrations decrease downstream in the Illinois Waterway due to dilution, but are always elevated relative to tributaries downriver from Chicago. The TWW component is especially noticeable downstream under low discharge conditions during summer and early autumn when surface drainage is at a minimum and agricultural drain tiles are not flowing. Increases in population, urban and residential areas, and roadways in the Chicago area have caused an increase in the flux of Cl- from both road salt and TWW. Chloride concentrations have been increasing in the Illinois Waterway since around 1960 at a rate of about 1 mg/L/a. The increase is largest in the winter months due to road salt runoff. Shallow groundwater Cl- concentrations are also increasing, potentially producing higher base flow concentrations. Projected increases in population and

  4. Chloride absorption in salt-sensitive Carrizo citrange and salt-tolerant Cleopatra mandarin citrus rootstocks is linked to water use.

    PubMed

    Moya, José Luís; Gómez-Cadenas, Aurelio; Primo-Millo, Eduardo; Talon, Manuel

    2003-02-01

    In this work, seedlings of two citrus rootstocks, the salt-tolerant Cleopatra mandarin (Citrus reshni Hort. ex Tan.) and the salt-sensitive Carrizo citrange (Citrus sinensis [L.] Osb. x Poncirus trifoliata [L.] Raf.) were used to study the relationship between chloride and water uptake. The results indicated that net chloride uptake rates in both genotypes were alike and decreased linearly with the time of salinity exposure, although they were more rapidly reduced in the tolerant genotype. In each rootstock, chloride uptake rates paralleled the decreases in transpiration rates. When transpiration was modified, concomitant changes in leaf Cl(-) concentrations were observed. There was a high positive correlation between total chloride content per plant and total water absorbed. In addition, the data indicate that the tolerant genotype "excluded" more chloride, i.e. it absorbed lower amounts of chloride per volume of water. Cleopatra also possessed a less efficient root system for water uptake and a higher shoot-to-root ratio. The results show that, overall, chloride absorption is linked to water use and that further tolerance in Cleopatra is mostly conferred by superior root resistance to Cl(-) uptake. Therefore, it is proposed that chloride absorption and, hence, salt tolerance in citrus depends to a great extent upon water use.

  5. Alkali Halide Opacity in Brown Dwarf and Cool Stellar Atmospheres: A Study of Lithium Chloride

    NASA Astrophysics Data System (ADS)

    Kirby, K.; Weck, P. F.; Schweitzer, A.; Stancil, P. C.; Hauschildt, P. H.

    2003-12-01

    Recent thermochemical equilibrium calculations have revealed the important role played by lithium chloride in the lithium chemistry of cool dwarf atmospheres (K. Lodders 1999, ApJ 519, 793). Indeed, LiCl appears to be the dominant Li-bearing gas over an extended domain of the (P,T) diagram, typically for temperatures below 1500 K. LiCl has a large dipole moment in its ground electronic state which can give rise to intense rovibrational line spectra. In addition, LiCl can make dipole transitions to several low-lying unbound excited states, causing dissociation of the molecule. For these reasons, LiCl may be a significant source of line and continuum opacity in brown dwarf and cool stellar atmospheres. In this work, we report calculations of complete lists of line oscillator strengths and photodissociation cross sections for the low-lying electronic states of LiCl. We have performed single- and double-excitation configuration interaction calculations using the ALCHEMY ab initio package (Mc Lean et al. 1991, MOTECC 91, Elsevier, Leiden) and obtained the potential curves and the corresponding dipole transition moment functions between the X 1Σ ^+ ground state and the B 1Σ ^+ and A 1Π excited states. The resulting line oscillator strengths and molecular photodissociation cross sections have been included in the PHOENIX stellar atmosphere code (Hauschildt & Baron 1999, J. Comput. App. Math. 102, 41). The new models, calculated using spherical geometry for all gravities considered, also incorporate our latest database of nearly 670 million molecular lines, and updated equations of state (EOS). This work was supported in part by NSF grants AST-9720704 and AST-0086246, NASA grants NAG5-8425, NAG5-9222, and NAG5-10551 as well as NASA/JPL grant 961582.

  6. Effects of arbuscular mycorrhizal fungi on the growth, photosynthesis and photosynthetic pigments of Leymus chinensis seedlings under salt-alkali stress and nitrogen deposition.

    PubMed

    Lin, Jixiang; Wang, Yingnan; Sun, Shengnan; Mu, Chunsheng; Yan, Xiufeng

    2017-01-15

    Leymus chinensis is the most promising grass species for salt-alkaline grassland restoration in northern China. However, little information exists concerning the role of arbuscular mycorrhizal (AM) symbiosis in the adaptation of seedlings to salt-alkali stress, particularly under increased nitrogen deposition, which has become a major environmental problem throughout the world. In this study, Leymus chinensis seedlings were cultivated in soil with 0, 100 and 200mM NaCl/NaHCO3 under two forms of nitrogen (10mM NH4NO3 or NH4Cl: NH4NO3=3:1), and the root colonization, growth and photosynthetic characteristics of the seedlings were measured. The results showed that the colonization rate and intensity decreased with increasing salt-alkali stress and were much lower under alkali stress. The nitrogen treatments also decreased the colonization, particularly under the NH4(+)-N treatment. Compared with the non-mycorrhizal controls, mycorrhizal seedlings generally presented higher plant biomass, photosynthetic parameters and contents of photosynthetic pigments under stresses, and the inhibitive effects of alkali stress were substantially stronger. In addition, both nitrogen forms decreased the physiological indexes compared with those of the AM seedlings. Our results suggest that salt stress and alkali stress are significantly different and that the salt-alkali tolerance of Leymus chinensis seedlings could be enhanced by associations with arbuscular mycorrhizal fungi, in which would yield better plant growth and photosynthesis. Excessive nitrogen in the soil affects mycorrhizal colonization and thereby inhibits the growth and photosynthetic ability of the seedlings.

  7. Preliminary projections of the effects of chloride-control structures on the Quaternary aquifer at Great Salt Plains, Oklahoma

    USGS Publications Warehouse

    Reed, J.E.

    1982-01-01

    About 1,200 tons of chloride per day are added to the salt load of the Salt Fork of the Arkansas River at Great Salt Plains Lake from natural sources. The source of this chloride is brine discharge from the rocks of Permian age in the vicinity of the lake. The U.S. Army Corps of Engineers has planned a chloride-control project. The Corps requested that the U.S. Geological Survey use a digital model to project the effects of the chloride-control plan on ground water. Ground-water flow and ground-water transport models were calibrated to represent the Quaternary aquifer that is the near-surface part of the flow system. The models were used to project the effects of planned chloride-control structures. Based on model results, ground-water levels are projected to rise as much as 19 feet. However, these water-level rises will occur only in areas near three reservoirs. Changes in ground-water level caused by the project will be small throughout most of the area. Chloride concentration of ground water is projected to increase by more than 90,000 milligrams per liter at one location. However, significant increases in chloride concentration during the 50-year period simulated are projected to be limited to areas where the ground water already contains excessive chloride concentrations.

  8. Oxidation behavior of Cr(III) during thermal treatment of chromium hydroxide in the presence of alkali and alkaline earth metal chlorides.

    PubMed

    Mao, Linqiang; Gao, Bingying; Deng, Ning; Liu, Lu; Cui, Hao

    2016-02-01

    The oxidation behavior of Cr(III) during the thermal treatment of chromium hydroxide in the presence of alkali and alkaline earth metal chlorides (NaCl, KCl, MgCl2, and CaCl2) was investigated. The amounts of Cr(III) oxidized at various temperatures and heating times were determined, and the Cr-containing species in the residues were characterized. During the transformation of chromium hydroxide to Cr2O3 at 300 °C approximately 5% of the Cr(III) was oxidized to form intermediate compounds containing Cr(VI) (i.e., CrO3), but these intermediates were reduced to Cr2O3 when the temperature was above 400 °C. Alkali and alkaline earth metals significantly promoted the oxidation of Cr(III) during the thermal drying process. Two pathways were involved in the influences the alkali and alkaline earth metals had on the formation of Cr(VI). In pathway I, the alkali and alkaline earth metals were found to act as electron transfer agents and to interfere with the dehydration process, causing more intermediate Cr(VI)-containing compounds (which were identified as being CrO3 and Cr5O12) to be formed. The reduction of intermediate compounds to Cr2O3 was also found to be hindered in pathway I. In pathway II, the alkali and alkaline earth metals were found to contribute to the oxidation of Cr(III) to form chromates. The results showed that the presence of alkali and alkaline earth metals significantly increases the degree to which Cr(III) is oxidized during the thermal drying of chromium-containing sludge.

  9. Geopolymer encapsulation of a chloride salt phase change material for high temperature thermal energy storage

    NASA Astrophysics Data System (ADS)

    Jacob, Rhys; Trout, Neil; Raud, Ralf; Clarke, Stephen; Steinberg, Theodore A.; Saman, Wasim; Bruno, Frank

    2016-05-01

    In an effort to reduce the cost and increase the material compatibility of encapsulated phase change materials (EPCMs) a new encapsulated system has been proposed. In the current study a molten salt eutectic of barium chloride (53% wt.), potassium chloride (28% wt.) and sodium chloride (19% wt.) has been identified as a promising candidate for low cost EPCM storage systems. The latent heat, melting point and thermal stability of the phase change material (PCM) was determined by DSC and was found to be in good agreement with results published in the literature. To cope with the corrosive nature of the PCM, it was decided that a fly-ash based geopolymer met the thermal and economic constraints for encapsulation. The thermal stability of the geopolymer shell was also tested with several formulations proving to form a stable shell for the chosen PCM at 200°C and/or 600°C. Lastly several capsules of the geopolymer shell with a chloride PCM were fabricated using a variety of methods with several samples remaining stable after exposure to 600°C testing.

  10. Isolation and characterization of a novel leaf-inhabiting osmo-, salt-, and alkali-tolerant Yarrowia lipolytica yeast strain.

    PubMed

    Zvyagilskaya, R; Andreishcheva, E; Soares, M I; Khozin, I; Berhe, A; Persson, B L

    2001-01-01

    Salt-excreting leaves of Atriplex halimus plants harvested in the central Negev Highlands of Israel were screened for yeasts inhabiting their surfaces. Several aerobic, moderately salt- and alkali-tolerant yeasts were isolated. One of the isolates (tentatively designated S-8) was identified as Yarrowia lipolytica (Wick.) van der Walt and Arx, on the basis of its morphological, biochemical/physiological characteristics, and of quantitative chemotaxonomic and molecular marker analyses. However, the strain is distinguished from the known members of the type Y. lipolytica strain by its pronounced osmo-, salt-, and pH tolerance. Cells displayed a unique capacity to grow over a wide pH range (from 3.5 to 11.5) with a pH optimum at 4.5 to 7.5. It is proposed that the S-8 strain be assigned to a single Y. lipolytica species as its anamorpha, or as a new variety, Y. lipolytica var. alkalitolerance. The ecophysiological properties and biotechnological potentials of the new strain are discussed.

  11. Adsorption of N-alkylpyridinium chlorides from water and salt solutions on cellulose acetate ultrafiltration membranes

    SciTech Connect

    Klimenko, N.A.; Yaroshenko, N.A.; Kondratova, T.B.

    1988-09-01

    A study has been made of the adsorption of three homologues in the N-alkylpyridinium chloride series from water and salt solutions, over a wide range of concentrations, on cellulose acetate ultrafiltration membranes, Grades UAM-500 and UAM-150. When adsorption takes place from true solutions, the membrane surface is hydrophobized. In the region of micellar solutions, nonassociated molecules and micelles are adsorbed in the mesopores and supermicropores, forming a mosaic adsorption layer. The thickness of the modifying layer depends on the length of the hydrophobic radical and on the composition of the system.

  12. Cloning of a vacuolar H(+)-pyrophosphatase gene from the halophyte Suaeda corniculata whose heterologous overexpression improves salt, saline-alkali and drought tolerance in Arabidopsis.

    PubMed

    Liu, Liang; Wang, Ying; Wang, Nan; Dong, Yuan-Yuan; Fan, Xiu-Duo; Liu, Xiu-Ming; Yang, Jing; Li, Hai-Yan

    2011-09-01

    Salt, saline-alkali conditions, and drought are major environmental factors limiting plant growth and productivity. The vacuolar H(+)-translocating inorganic pyrophosphatase (V-H(+)-PPase) is an electrogenic proton pump that translocates protons into vacuoles in plant cells. Expression of V-H(+)-PPase increases in plants under a number of abiotic stresses, and is thought to have an important role in adaptation to abiotic stress. In this work, we report the isolation and characterization of the gene, ScVP, encoding a vacuolar inorganic pyrophosphatase (V-H(+)-PPase) from the halophyte, Suaeda corniculata. Semi-quantitative reverse transcription-polymerase chain reaction analysis showed that ScVP was induced in roots, stems and leaves under treatment with salt, saline-alkali and drought. Compared with wild-type (WT) Arabidopsis, transgenic plants overexpressing ScVP accumulated more Na(+) in leaves and roots, and showed increased tolerance to high salinity, saline-alkali and drought stresses. The germination percentage of transgenic Arabidopsis seeds was higher than that of WT seeds under the abiotic stresses. The root length of transgenic plants under salt stress was longer than that of WT plants. Furthermore, the rate of water loss during drought stress was higher in WT than in transgenic plants. Collectively, these results indicate that ScVP plays an important role in plant tolerance to salt, saline-alkali and drought stress.

  13. The Composition and Physical Properties of Chloride Salt-bearing Deposits on Mars

    NASA Astrophysics Data System (ADS)

    Glotch, T. D.; Bandfield, J.; Wolff, M. J.; Arnold, J. A.; Che, C.

    2015-12-01

    Anhydrous chloride salt deposits were first discovered on Mars by the 2001 Odyssey Thermal Emission Imaging System (THEMIS) and have been further characterized by Mars Reconnaissance Orbiter CRISM and Mars Express visible/near-IR (VNIR) hyperspectral imaging spectrometers. At mid-IR wavelengths, the salt-bearing deposits display a blue slope superimposed on the regional regolith spectral shape. At VNIR wavelengths, ratio spectra display a featureless red slope between 1.0 and 2.5 μm and a reduced 3 μm band, indicating that the deposits are desiccated compared to the surrounding terrain. In this work, we compare laboratory and model spectra to THEMIS spectra to evaluate the abundance and physical properties of salt in these deposits. We acquired mid-IR emissivity spectra of a suite of halite/basalt mixtures separated to <10 μm, 63-90 μm, 125-180 μm, and 250-355 μm. Halite concentrations for each size separate ranged from 1-75%. Laboratory spectra of the coarsest particulates do not adequately reproduce the spectral shapes associated with any of the Martian salt deposits. The finest particulates display spectral characteristics associated with salt deposits found in high albedo, dusty regions of Mars, and those in the middle size ranges are consistent with the spectra of most Martian salt deposits and suggest abundances between 10 and 25 wt.% salt. The increase in salt content from ~10-25% coincides with a shift in the THEMIS emissivity maximum from band 3 to band 4, suggesting this can be used as a rough indicator of salt content in remote sensing studies. We also used a hybrid T-matrix/Hapke light scattering model to model the scattering properties and mid-IR spectra of clusters of salt/silicate spheres. The model results show that as halite content is increased, the transparency of the cluster increases substantially, resulting in multiple internal scattering, and substantially reduced emissivity, consistent with the THEMIS data and laboratory spectra. Phase

  14. Thermal Analysis of Surrogate Simulated Molten Salts with Metal Chloride Impurities for Electrorefining Used Nuclear Fuel

    SciTech Connect

    Toni Y. Gutknecht; Guy L. Fredrickson; Vivek Utgikar

    2012-04-01

    This project is a fundamental study to measure thermal properties (liquidus, solidus, phase transformation, and enthalpy) of molten salt systems of interest to electrorefining operations, which are used in both the fuel cycle research & development mission and the spent fuel treatment mission of the Department of Energy. During electrorefining operations the electrolyte accumulates elements more active than uranium (transuranics, fission products and bond sodium). The accumulation needs to be closely monitored because the thermal properties of the electrolyte will change as the concentration of the impurities increases. During electrorefining (processing techniques used at the Idaho National Laboratory to separate uranium from spent nuclear fuel) it is important for the electrolyte to remain in a homogeneous liquid phase for operational safeguard and criticality reasons. The phase stability of molten salts in an electrorefiner may be adversely affected by the buildup of fission products in the electrolyte. Potential situations that need to be avoided are: (i) build up of fissile elements in the salt approaching the criticality limits specified for the vessel (ii) freezing of the salts due to change in the liquidus temperature and (iii) phase separation (non-homogenous solution) of elements. The stability (and homogeneity) of the phases can potentially be monitored through the thermal characterization of the salts, which can be a function of impurity concentration. This work describes the experimental results of typical salts compositions, consisting of chlorides of strontium, samarium, praseodymium, lanthanum, barium, cerium, cesium, neodymium, sodium and gadolinium (as a surrogate for both uranium and plutonium), used in the processing of used nuclear fuels. Differential scanning calorimetry was used to analyze numerous salt samples providing results on the thermal properties. The property of most interest to pyroprocessing is the liquidus temperature. It was

  15. Nonlinear optical study of 1-(carboxymethyl)-8-hydroxyquinolin-1-ium chloride and 1-(carboxymethyl)quinolin-1-ium chloride salts by Z-scan technique

    NASA Astrophysics Data System (ADS)

    Zidan, M. D.; Arfan, A.; Allahham, A.

    2016-12-01

    Z-scan technique was used to investigate the nonlinear optical properties of 1-(carboxymethyl)-8-hydroxyquinolin-1-ium chloride and 1-(carboxymethyl)quinolin-1-ium chloride salts. The new 1-(carboxymethyl)-8-hydroxyquinolin-1-ium chloride and 1-(carboxymethyl)quinolin-1-ium chloride salts were synthesized and characterized using UV-visible, FTIR and NMR measurements and the characterization spectra confirm the expected molecular structure of the prepared salts. Measurements were performed with a CW Diode laser at 635 nm wavelength and 26 mW power. The nonlinear optical absorption coefficient (β) and nonlinear refractive index (n2) of the 1-(carboxymethyl)-8-hydroxyquinolin-1-ium chloride was affected by OH group. The excited-state absorption cross sections (σex) and the ground -state absorption cross sections (σg) were calculated for the two studied compounds. It was found that the σex is larger than the σg, indicating that the reverse saturable absorption mechanism (RSA) is the dominating mechanism for the observed absorption nonlinearities. Our results suggest that this material should be considered as a promising candidate for future optical devices applications.

  16. Enhanced piezoresponse of electrospun PVDF mats with a touch of nickel chloride hexahydrate salt.

    PubMed

    Dhakras, Dipti; Borkar, Vivek; Ogale, Satishchandra; Jog, Jyoti

    2012-02-07

    PVDF nanofibers are prepared using electrospinning. The effect of addition of a hydrated salt, nickel chloride hexahydrate (NiCl(2)·6H(2)O), on the phase formation is examined. Addition of the hydrated salt (NC) is found to enhance the polar β phase by about 30%. The peak to peak piezo-voltage generated for PVDF NC is almost 0.762 V, a factor of 3 higher than that for PVDF. The fiber mats exhibit a significantly enhanced dynamic strain sensor response. The voltage generated per unit micro-strain developed during the free vibration test for PVDF was 0.119 mV whereas it was 0.548 mV for PVDF NC, exhibiting a non-linearly enhanced performance vis a vis the increase in the β phase component.

  17. Hydrogen bonding Part 38. IR and thermodynamic study of phosphorylcholine chloride calcium salt tetrahydrate and monohydrate

    NASA Astrophysics Data System (ADS)

    Harmon, Kenneth M.; Akin, Anne C.

    1991-09-01

    Vapor pressure vs. H 2O content studies demonstrate that phosphorylcholine chloride calcium salt forms two hydrates, a monohydrate and a tetrahydrate, in the range 0-4 mol H 20 mol -1 of salt; there is no dihydrate or trihydrate. Equilibrium vapor pressure measurements show that ΔH 0 of dissociation per mol H 20 lost is greater for the tetrahydrate (16.08 kcal mol -1) than for the monohydrate (12.49 kcal mo -1); the lower stability of the tetrahydrate arises from entropy effects. The IR spectrum of the tetrahydrate is that of a framework clathrate hydrate and suggests that the -P0 3 group may act as a very weak hydrogen-bond acceptor. In the monohydrate the -P0 3 group is not involved in hydrogen bonding. Neither hydrate contains POH bonds.

  18. MgAl2O4 spinel refractory as containment liner for high-temperature alkali salt containing environments

    DOEpatents

    Peascoe-Meisner, Roberta A [Knoxville, TN; Keiser, James R [Oak Ridge, TN; Hemric, James G [Knoxville, TN; Hubbard, Camden R [Oak Ridge, TN; Gorog, J Peter [Kent, WA; Gupta, Amul [Jamestown, NY

    2008-10-21

    A method includes containing a high-temperature alkali salt containing environment using a refractory containment liner containing MgAl.sub.2O.sub.4 spinel. A method, includes forming a refractory brick containing MgAl.sub.2O.sub.4 spinel having an exterior chill zone defined by substantially columnar crystallization and an interior zone defined by substantially equiaxed crystallization; and removing at least a portion of the exterior chill zone from the refractory brick containing MgAl.sub.2O.sub.4 spinel by scalping the refractory brick containing MgAl.sub.2O.sub.4 spinel to define at least one outer surface having an area of substantially equiaxed crystallization. A product of manufacture includes a refractory brick containing MgAl.sub.2O.sub.4 spinel including an interior zone defined by substantially equiaxed crystallization; and at least one outer surface having an area of substantially equiaxed crystallization.

  19. Enhanced piezoresponse of electrospun PVDF mats with a touch of nickel chloride hexahydrate salt

    NASA Astrophysics Data System (ADS)

    Dhakras, Dipti; Borkar, Vivek; Ogale, Satishchandra; Jog, Jyoti

    2012-01-01

    PVDF nanofibers are prepared using electrospinning. The effect of addition of a hydrated salt, nickel chloride hexahydrate (NiCl2.6H2O), on the phase formation is examined. Addition of the hydrated salt (NC) is found to enhance the polar β phase by about 30%. The peak to peak piezo-voltage generated for PVDF NC is almost 0.762 V, a factor of 3 higher than that for PVDF. The fiber mats exhibit a significantly enhanced dynamic strain sensor response. The voltage generated per unit micro-strain developed during the free vibration test for PVDF was 0.119 mV whereas it was 0.548 mV for PVDF NC, exhibiting a non-linearly enhanced performance vis a vis the increase in the β phase component.PVDF nanofibers are prepared using electrospinning. The effect of addition of a hydrated salt, nickel chloride hexahydrate (NiCl2.6H2O), on the phase formation is examined. Addition of the hydrated salt (NC) is found to enhance the polar β phase by about 30%. The peak to peak piezo-voltage generated for PVDF NC is almost 0.762 V, a factor of 3 higher than that for PVDF. The fiber mats exhibit a significantly enhanced dynamic strain sensor response. The voltage generated per unit micro-strain developed during the free vibration test for PVDF was 0.119 mV whereas it was 0.548 mV for PVDF NC, exhibiting a non-linearly enhanced performance vis a vis the increase in the β phase component. Electronic supplementary information (ESI) available. See DOI: 10.1039/c2nr11841f

  20. Secretion by the nasal salt glands of two insectivorous lizard species is initiated by an ecologically relevant dietary ion, chloride.

    PubMed

    Hazard, Lisa C; Lechuga, Claudia; Zilinskis, Stephanie

    2010-08-01

    Salt glands are used by some vertebrates to excrete hyperosmotic NaCl or KCl solutions in response to dietary salt loads. Control of secretion varies across taxa; some secrete in response to osmotic challenges while others secrete in response to specific dietary ions. We hypothesized that differences in control could be related to different diet-related selective pressures on herbivorous, marine, and insectivorous species. We studied control of secretion and flexibility of cation (sodium or potassium) and anion (chloride or bicarbonate) secretion in two insectivorous lizard species, Schneider's skinks (Eumeces schneideri, Scincidae) and green anoles (Anolis carolinensis, Polychrotidae). Lizards were injected daily for four days with combinations of cations (potassium, sodium, and histidine control) and anions (chloride and acetate control), isoosmotic saline, or sham injection. Secretions were collected daily and analyzed for sodium, potassium, and chloride. Both species secreted only in response to chloride; sodium appeared to have a slight inhibitory effect. Regardless of cation load, skinks secreted a combination of potassium and sodium, while anoles secreted solely potassium. In both species, total cation secretion was matched closely by chloride; very little bicarbonate was secreted. As predicted, secretion in insectivorous lizards was initiated by the dietary ion ecologically most important for these species, chloride, which otherwise cannot be excreted without significant water loss (unlike the cations, which may be excreted as insoluble urate salts). This gives further support to the hypothesis that ecological factors drive the evolution of control mechanisms in lizard salt glands.

  1. Candidate waste forms for immobilisation of waste chloride salt from pyroprocessing of spent nuclear fuel

    NASA Astrophysics Data System (ADS)

    Vance, E. R.; Davis, J.; Olufson, K.; Chironi, I.; Karatchevtseva, I.; Farnan, I.

    2012-01-01

    Sodalite/glass bodies prepared by hot isostatic pressing (HIPing) at ˜850 °C/100 MPa are candidates for immobilising fission product-bearing waste KCl-LiCl pyroprocessing salts. To study the capacity of sodalite to structurally incorporate such pyroprocessing salts, K, Li, Cs, Sr, Ba and La were individually targeted for substitution in a Na site in sodalite (Na vacancies targeted as charge compensators for alkaline and rare earths) and studied by X-ray diffraction and scanning electron microscopy after sintering in the range of 800-1000 °C. K and Li appeared to enter the sodalite, but Cs, Sr and Ba formed aluminosilicate phases and La formed an oxyapatite phase. However these non-sodalite phases have reasonable resistance to water leaching. Pure chlorapatite gives superior leach resistance to sodalite, and alkalis, alkaline and rare earth ions are generally known to enter chlorapatite, but attempts to incorporate simulated waste salt formulations into HIPed chlorapatite-based preparations or to substitute Cs alone into the structure of Ca-based chlorapatite were not successful on the basis of scanning electron microscopy. The materials exhibited severe water leachability, mainly in regard to Cs release. Attempts to substitute Cs into Ba- and Sr-based chlorapatites also did not look encouraging. Consequently the use of apatite alone to retain fission product-bearing waste pyroprocessing salts from electrolytic nuclear fuel reprocessing is problematical, but chlorapatite glass-ceramics may be feasible, albeit with reduced waste loadings. Spodiosite, Ca 2(PO 4)Cl, does not appear to be suitable for incorporation of Cl-bearing waste containing fission products.

  2. Alkali metal ion battery with bimetallic electrode

    DOEpatents

    Boysen, Dane A; Bradwell, David J; Jiang, Kai; Kim, Hojong; Ortiz, Luis A; Sadoway, Donald R; Tomaszowska, Alina A; Wei, Weifeng; Wang, Kangli

    2015-04-07

    Electrochemical cells having molten electrodes having an alkali metal provide receipt and delivery of power by transporting atoms of the alkali metal between electrode environments of disparate chemical potentials through an electrochemical pathway comprising a salt of the alkali metal. The chemical potential of the alkali metal is decreased when combined with one or more non-alkali metals, thus producing a voltage between an electrode comprising the molten the alkali metal and the electrode comprising the combined alkali/non-alkali metals.

  3. Characterization of chloride transport in the unsaturated zone near salted road

    NASA Astrophysics Data System (ADS)

    Lax, Samanta; Peterson, Eric W.

    2009-09-01

    The application of road salts as deicing agents contributes to the anthropogenic loading of chloride (Cl-) on the environment. Using a 2D solute model, the potential of the unsaturated zone to serve as a reservoir and the mechanisms controlling the movement of Cl- were examined. Physical properties and initial pore-water Cl- concentrations were derived from an array of soil borings. Initial pore-water concentrations show the presence of a Cl- “slug” approximately 0.75 m below the surface. Simulations show that within the unsaturated zone, Cl- transport is predominantly vertical, driven by molecular diffusion. After a 1-year simulation, a Cl- slug similar to the background observation was noted. While Cl- is retained in the unsaturated zone, a net loss of Cl- from the unsaturated zone was simulated for the first 10 years. In year 11, an equilibrium between the Cl- input and output is achieved. The presence of Cl- in the unsaturated zone becomes a long-term source of chloride to the groundwater, which eventually discharges into the surface water. Historically, surface water chemistry data support the continual discharge of chloride to the surface water in the area, further supporting the hypothesis that the unsaturated zone serves as a Cl- reservoir.

  4. The flux of methyl chloride along an elevational gradient of a coastal salt marsh, Eastern China

    NASA Astrophysics Data System (ADS)

    Wang, Jinxin; Li, Rongjin; Guo, Yingyan; Qin, Pei; Sun, Shucun

    Salt marshes have been suggested to be a large potential source for methyl chloride (CH 3Cl) that is the major natural carrier of chlorine to the stratosphere. However, the global budget of this trace gas is uncertain, and the empirical field data are still lacking. In this study, CH 3Cl fluxes were measured seasonally using static flux chambers from April 2004 to January 2005, along an elevational gradient of a coastal salt marsh in eastern China. To estimate the contribution of higher plants to the flux, plant aboveground biomass was experimentally removed and the flux difference between the treatment and the intact was examined. In addition, the flux was analyzed in relation to soil and weather conditions. Along the elevational gradient, the salt marsh generally functioned as a net sink in the growing season (from April to October 2004). The flux of CH 3Cl ranged between -1.27 and -29.33 μmol m -2 d -1 (positive for emission and negative for consumption), and the maximum negative rates occurred at the mudflat and the cordgrass ( Spartina alterniflora) marsh. However, the measurements made during inundation indicated that the mudflat was a net source of the gas. In the non-growing season (from November to March), the vegetated flat, when frozen, was a minor source of methyl chloride, with an emission rate ranging from 0.27 to 9.13 μmol m -2 d -1. However, the measurements made during non-frozen periods indicate that the mudflat was a minor sink of methyl chloride. Overall, the study marsh was a large net sink for the gas because the magnitude of the consumption rates was lager than that of emission, and because the duration of the growing season was longer than that of the non-growing season. Plant aboveground biomass had a great effect on the flux. Comparative analyses showed that higher plants were present as an important source of CH 3Cl, and it could balance 17.26-67.66% of the soil consumption. The net CH 3Cl consumption rate was negatively correlated to

  5. Raman Analysis of Perrhenate and Pertechnetate in Alkali Salts and Borosilicate Glasses

    SciTech Connect

    Gassman, Paul L.; McCloy, John S.; Soderquist, Chuck Z.; Schweiger, Michael J.

    2014-01-03

    Sodium borosilicate glasses containing various concentrations of rhenium or technetium were fabricated, and their vibrational spectra studied using a Raman microscope. Spectra were interpreted with reference to new high resolution measurements of alkali pertechnetates and perrhenates NaReO4, KReO4, NaTcO4, and KTcO4. At low concentrations of ReO4- or TcO4-, glass spectra show weak peaks superimposed on a dominant spectrum of glass characteristic of silicate and borate network vibrations. At high concentrations, sharp peaks characteristic of crystal field splitting and C4h symmetry dominate the spectra of glasses, indicating alkali nearby tetrahedral Re or Tc. Often peaks indicative of both the K and Na pertechnetates/ perrhenates are evident in the Raman spectrum, with the latter being favored at high additions of the source chemical, since Na is more prevalent in the glass and ion exchange takes place. These results have significance to immobilization of nuclear waste containing radioactive 99Tc in glass for ultimate disposal.

  6. Tin-containing silicates: alkali salts improve methyl lactate yield from sugars.

    PubMed

    Tolborg, Søren; Sádaba, Irantzu; Osmundsen, Christian M; Fristrup, Peter; Holm, Martin S; Taarning, Esben

    2015-02-01

    This study focuses on increasing the selectivity to methyl lactate from sugars using stannosilicates as heterogeneous catalyst. All group I ions are found to have a promoting effect on the resulting methyl lactate yield. Besides, the alkali ions can be added both during the preparation of the catalyst or directly to the solvent mixture to achieve the highest reported yield of methyl lactate (ca. 75 %) from sucrose at 170 °C in methanol. The beneficial effect of adding alkali to the reaction media applies not only to highly defect-free Sn-Beta prepared through the fluoride route, but also to materials prepared by post-treatment of dealuminated commercial Beta zeolites, as well as ordered mesoporous stannosilicates, in this case Sn-MCM-41 and Sn-SBA-15. These findings open the door to the possibility of using other preparation methods or different Sn-containing silicates with equally high methyl lactate yields as Sn-Beta.

  7. A reactive distillation process for the treatment of LiCl-KCl eutectic waste salt containing rare earth chlorides

    NASA Astrophysics Data System (ADS)

    Eun, H. C.; Choi, J. H.; Kim, N. Y.; Lee, T. K.; Han, S. Y.; Lee, K. R.; Park, H. S.; Ahn, D. H.

    2016-11-01

    The pyrochemical process, which recovers useful resources (U/TRU metals) from used nuclear fuel using an electrochemical method, generates LiCl-KCl eutectic waste salt containing radioactive rare earth chlorides (RECl3). It is necessary to develop a simple process for the treatment of LiCl-KCl eutectic waste salt in a hot-cell facility. For this reason, a reactive distillation process using a chemical agent was achieved as a method to separate rare earths from the LiCl-KCl waste salt. Before conducting the reactive distillation, thermodynamic equilibrium behaviors of the reactions between rare earth (Nd, La, Ce, Pr) chlorides and the chemical agent (K2CO3) were predicted using software. The addition of the chemical agent was determined to separate the rare earth chlorides into an oxide form using these equilibrium results. In the reactive distillation test, the rare earth chlorides in LiCl-KCl eutectic salt were decontaminated at a decontamination factor (DF) of more than 5000, and were mainly converted into oxide (Nd2O3, CeO2, La2O3, Pr2O3) or oxychloride (LaOCl, PrOCl) forms. The LiCl-KCl was purified into a form with a very low concentration (<1 ppm) for the rare earth chlorides.

  8. Individual effects of sodium, potassium, calcium, and magnesium chloride salts on Lactobacillus pentosus and Saccharomyces cerevisiae growth.

    PubMed

    Bautista-Gallego, J; Arroyo-López, F N; Durán-Quintana, M C; Garrido-Fernandez, A

    2008-07-01

    A quantitative investigation on the individual effects of sodium (NaCl), potassium (KCl), calcium (CaCl2), and magnesium (MgCl2) chloride salts against Lactobacillus pentosus and Saccharomyces cerevisiae, two representative microorganisms of table olives and other fermented vegetables, was carried out. In order to assess their potential activities, both the kinetic growth parameters and dose-response profiles in synthetic media (deMan Rogosa Sharpe broth medium and yeast-malt-peptone-glucose broth medium, respectively) were obtained and analyzed. Microbial growth was monitored via optical density measurements as a function of contact time in the presence of progressive chloride salt concentrations. Relative maximum specific growth rate and lag-phase period were modeled as a function of the chloride salt concentrations. Moreover, for each salt and microorganism tested, the noninhibitory concentrations and the MICs were estimated and compared. All chloride salts exerted a significant antimicrobial effect on the growth cycle; particularly, CaCl2 showed a similar effect to NaCl, while KCl and MgCl2 were progressively less inhibitory. Microbial susceptibility and resistance were found to be nonlinearly dose related.

  9. Effect of Sodium Sulfate, Ammonium Chloride, Ammonium Nitrate, and Salt Mixtures on Aqueous Phase Partitioning of Organic Compounds.

    PubMed

    Wang, Chen; Lei, Ying Duan; Wania, Frank

    2016-12-06

    Dissolved inorganic salts influence the partitioning of organic compounds into the aqueous phase. This influence is especially significant in atmospheric aerosol, which usually contains large amounts of ions, including sodium, ammonium, chloride, sulfate, and nitrate. However, empirical data on this salt effect are very sparse. Here, the partitioning of numerous organic compounds into solutions of Na2SO4, NH4Cl, and NH4NO3 was measured and compared with existing data for NaCl and (NH4)2SO4. Salt mixtures were also tested to establish whether the salt effect is additive. In general, the salt effect showed a decreasing trend of Na2SO4 > (NH)2SO4 > NaCl > NH4Cl > NH4NO3 for the studied organic compounds, implying the following relative strength of the salt effect of individual anions: SO4(2-) > Cl(-) > NO3(-) and of cations: Na(+) > NH4(+). The salt effect of different salts is moderately correlated. Predictive models for the salt effect were developed based on the experimental data. The experimental data indicate that the salt effect of mixtures may not be entirely additive. However, the deviation from additivity, if it exists, is small. Data of very high quality are required to establish whether the effect of constituent ions or salts is additive or not.

  10. Complex ion effects on polypeptide conformational stability: chloride and sulfate salts of guanidinium and tetrapropylammonium.

    PubMed

    Dempsey, Christopher E; Mason, Philip E; Jungwirth, Pavel

    2011-05-18

    The effects of chloride and sulfate salts of tetrapropylammonium (TPA(+)) and guanidinium (Gdm(+)) on the conformational stabilities of tryptophan zipper (trpzip) and α-helical (alahel) peptides were measured by circular dichroism spectroscopy. Like Gdm(+), TPA(+) interacts with the planar tryptophan indole group, perturbing the conformational stability of trpzip peptides. TPA(+) effects are largely unaffected by sulfate, indicating an absence of the heteroion pairing that is observed in concentrated Gdm(2)SO(4) solutions. TPA(+) stabilizes helical conformations in alahel peptides, indicating exclusion from the peptide bond. The observations are broadly consistent with predictions of molecular dynamics simulations [Mason, P. E.; et al. J. Phys. Chem. B2009, 113, 3227-3234], indicating that the effects of complex ions on proteins are increasingly predictable in terms of ion hydration, complementary interactions with specific protein groups, and ion-pairing contributions.

  11. How Sodium Chloride Salt Inhibits the Formation of CO2 Gas Hydrates.

    PubMed

    Holzammer, Christine; Finckenstein, Agnes; Will, Stefan; Braeuer, Andreas S

    2016-03-10

    We present an experimental Raman study on how the addition of sodium chloride to CO2-hydrate-forming systems inhibits the hydrate formation thermodynamically. For this purpose, the molar enthalpy of reaction and the molar entropy of reaction for the reaction of weakly hydrogen-bonded water molecules to strongly hydrogen bonded water molecules are determined for different salinities from the Raman spectrum of the water-stretching vibration. Simultaneously, the influence of the salinity on the solubility of CO2 in the liquid water-rich phase right before the start of hydrate formation is analyzed. The results demonstrate that various mechanisms contribute to the inhibition of gas hydrate formation. For the highest salt concentration of 20 wt % investigated, the temperature of gas hydrate formation is lowered by 12 K. For this concentration the molar enthalpy and entropy of reaction become smaller by 50 and 20%, respectively. Concurrently, the solubility of carbon dioxide is reduced by 70%. These results are compared with data in literature for systems of sodium chloride in water (without carbon dioxide).

  12. Hydration of lanthanide chloride salts: a quantum chemical and classical molecular dynamics simulation study.

    PubMed

    Beuchat, Cesar; Hagberg, Daniel; Spezia, Riccardo; Gagliardi, Laura

    2010-12-02

    We present the results of a quantum chemical and classical molecular dynamics simulation study of some solutions containing chloride salts of La(3+), Gd(3+), and Er(3+) at various concentrations (from 0.05 to 5 M), with the purpose of understanding their structure and dynamics and analyzing how the coordination varies along the lanthanide series. In the La-Cl case, nine water molecules surround the central La(3+) cation in the first solvation shell, and chloride is present only in the second shell for all solutions but the most concentrated one (5 M). In the Gd(3+) case, the coordination number is ∼8.6 for the two lowest concentrations (0.05 and 0.1 M), and then it decreases rapidly. In the Er(3+) case, the coordination number is 7.4 for the two lowest concentrations (0.05 and 0.1 M), and then it decreases. The counterion Cl(-) is not present in the first solvation shell in the La(3+) case for most of the solutions, but it becomes progressively closer to the central cation in the Gd(3+) and Er(3+) cases, even at low concentrations.

  13. Experimental Na/K exchange between alkali feldspar and an NaCl-KCl salt melt: chemically induced fracturing and element partitioning

    NASA Astrophysics Data System (ADS)

    Neusser, G.; Abart, R.; Fischer, F. D.; Harlov, D.; Norberg, N.

    2012-08-01

    The exchange of Na+ and K+ between alkali feldspar and a NaCl-KCl salt melt has been investigated experimentally. Run conditions were at ambient pressure and 850 °C as well as 1,000 °C. Cation exchange occurred by interdiffusion of Na+ and K+ on the feldspar sub-lattice, while the Si-Al framework remained unaffected. Due to the compositional dependence of the lattice parameters compositional heterogeneities resulting from Na+/K+ interdiffusion induced coherency stress and associated fracturing. Depending on the sense of chemical shift, different crack patterns developed. For the geometrically most regular case that developed when potassic alkali feldspar was shifted toward more sodium-rich compositions, a prominent set of cracks corresponding to tension cracks opened perpendicular to the direction of maximum tensile stress and did not follow any of the feldspar cleavage planes. The critical stress needed to initiate fracturing in a general direction of the feldspar lattice was estimated at ≤0.35 GPa. Fracturing provided fast pathways for penetration of salt melt or vapor into grain interiors enhancing overall cation exchange. The Na/K partitioning between feldspar and the salt melt attained equilibrium values in the exchanged portions of the grains allowing for extraction of the alkali feldspar mixing properties.

  14. [Physiological characteristics of Pinus densiflora var. zhangwuensis and Pinus sylvestris var. mongolica seedlings on sandy lands under salt-alkali stresses].

    PubMed

    Meng, Peng; Li, Yu-Ling; Zhang, Bai-xi

    2013-02-01

    For the popularization of Pinus densiflora var. zhangwuensis, a new afforestation tree species on the desertified and salinized-alkalized lands in Northern China, and to evaluate the salinity-alkalinity tolerance of the tree species and to better understand the tolerance mechanisms, a pot experiment with 4-year old P. densiflora var. zhangwuensis and P. sylvestris var. mongolica was conducted to study their seedlings growth and physiological and biochemical indices under the effects of three types salt (NaCl, Na2CO3, and NaHCO3 ) stresses and of alkali (NaOH) stress. Under the salt-alkali stresses, the injury level of P. densiflora var. zhangwuensis was lower, and the root tolerance index was higher. The leaf catalase (CAT) activity increased significantly by 22. 6 times at the most, as compared with the control; the leaf malondialdehyde (MDA) content had no significant increase; the leaf chlorophyll (Chl) content had a smaller decrement; and the leaf water content (LWC) increased slightly. P. sylvestris var. mongolica responded differently to the salt-alkali stresses. Its leaf CAT activity had less change, MDA content increased significantly, Chl content had significant decrease, and LWC decreased slightly. It was suggested that P. densi-flora var. zhangwuensis had a greater salinity-alkalinity tolerance than P. sylvestris var. mongolica. The higher iron concentration in P. densiflora var. zhangwuensis needles enhanced the CAT activity and Chl content, whereas the higher concentrations of zinc and copper were associated with the stronger salinity-alkalinity tolerance.

  15. Interactive role of nitric oxide and calcium chloride in enhancing tolerance to salt stress.

    PubMed

    Khan, M Nasir; Siddiqui, Manzer H; Mohammad, Firoz; Naeem, M

    2012-12-01

    Nitric oxide (NO), a small diffusible, ubiquitous bioactive molecule, acts as prooxidant as well as antioxidant, and also regulates remarkable spectrum of plant cellular mechanisms. The present work was undertaken to investigate the role of nitric oxide donor sodium nitroprusside (SNP) and/or calcium chloride (CaCl(2)) in the tolerance of excised mustard leaves to salt stress. After 24h, salt stressed leaves treated with SNP and/or CaCl(2), showed an improvement in the activities of carbonic anhydrase (CA) and nitrate reductase (NR), and leaf chlorophyll (Chl) content, leaf relative water content (LRWC) and leaf ion concentration as compared with the leaves treated with NaCl only. Salinity stress caused a significant increase in H(2)O(2) content and membrane damage which is witnessed by enhanced levels of thiobarbituric acid reactive substances (TBARS) and electrolyte leakage. By contrast, such increases were blocked by the application of 0.2mM SNP and 10mM CaCl(2) to salt stressed leaves. Application of SNP and/or CaCl(2) alleviated NaCl stress by enhancing the activities of antioxidative enzymes viz. superoxide dismutase (SOD), catalase (CAT), peroxidase (POX), ascorbate peroxidase (APX) and glutathione reductase (GR) and by enhancing proline (Pro) and glycinebetaine (GB) accumulation with a concomitant decrease in H(2)O(2) content, TBARS and electrolyte leakage, which is manifested in the tolerance of plants to salinity stress. Moreover, application of SNP with CaCl(2) was more effective to reduce the detrimental effects of NaCl stress on excised mustard leaves. In addition to this, ameliorating effect of SNP was not effective in presence of NO scavenger cPTIO [2-(4-carboxyphenyl)-4,4,5,5-tetramethylimidazoline-1-oxyl-3-oxide]. To put all these in a nut shell, the results advocate that SNP in association with CaCl(2) plays a role in enhancing the tolerance of plants to salt stress by improving antioxidative defence system, osmolyte accumulation and ionic

  16. APPLICATION OF VACUUM SALT DISTILLATION TECHNOLOGY FOR THE REMOVAL OF FLUORIDE AND CHLORIDE FROM LEGACY FISSILE MATERIALS

    SciTech Connect

    Pierce, R.; Peters, T.

    2011-11-01

    Between September 2009 and January 2011, the Savannah River National Laboratory (SRNL) and the Savannah River Site (SRS) HB-Line Facility designed, developed, tested, and successfully deployed a production-scale system for the distillation of sodium chloride (NaCl) and potassium chloride (KCl) from plutonium oxide (PuO{sub 2}). Subsequent efforts adapted the vacuum salt distillation (VSD) technology for the removal of chloride and fluoride from less-volatile halide salts at the same process temperature and vacuum. Calcium chloride (CaCl{sub 2}), calcium fluoride (CaF{sub 2}), and plutonium fluoride (PuF{sub 3}) were of particular concern. To enable the use of the same operating conditions for the distillation process, SRNL employed in situ exchange reactions to convert the less-volatile halide salts to compounds that facilitated the distillation of halide without removal of plutonium. SRNL demonstrated the removal of halide from CaCl{sub 2}, CaF{sub 2} and PuF{sub 3} below 1000 C using VSD technology.

  17. Method and system for producing lower alcohols. [Heteropolyatomic lead salt coated with alkali metal formate

    DOEpatents

    Rathke, J.W.; Klingler, R.J.; Heiberger, J.J.

    1983-09-26

    It is an object of the present invention to provide an improved catalyst for the reaction of carbon monoxide with water to produce methanol and other lower alcohols. It is a further object to provide a process for the production of methanol from carbon monoxide and water in which a relatively inexpensive catalyst permits the reaction at low pressures. It is also an object to provide a process for the production of methanol from carbon monoxide and water in which a relatively inexpensive catalyst permits the reaction at low pressures. It is also an object to provide a process for the production of methanol in which ethanol is also directly produced. It is another object to provide a process for the production of mixtures of methanol with ethanol and propanol from the reaction of carbon monoxide and water at moderate pressure with inexpensive catalysts. It is likewise an object to provide a system for the catalytic production of lower alcohols from the reaction of carbon monoxide and water at moderate pressure with inexpensive catalysts. In accordance with the present invention, a catalyst is provided for the reaction of carbon monoxide and water to produce lower alcohols. The catalyst includes a lead heteropolyatomic salt in mixture with a metal formate or a precursor to a metal formate.

  18. Lithium nickel cobalt manganese oxide synthesized using alkali chloride flux: morphology and performance as a cathode material for lithium ion batteries.

    PubMed

    Kim, Yongseon

    2012-05-01

    Li(Ni(0.8)Co(0.1)Mn(0.1))O(2) (NCM811) was synthesized using alkali chlorides as a flux and the performance as a cathode material for lithium ion batteries was examined. Primary particles of the powder were segregated and grown separately in the presence of liquid state fluxes, which induced each particle to be composed of one primary particle with well-developed facet planes, not the shape of agglomerates as appears with commercial NCMs. The new NCM showed far less gas emission during high temperature storage at charged states, and higher volumetric capacity thanks to its high bulk density. The material is expected to provide optimal performances for pouch type lithium ion batteries, which require high volumetric capacity and are vulnerable to deformation caused by gas generation from the electrode materials.

  19. Single crystal, vibrational and computational studies of Theophylline (a bronchodilator drug) and its chloride salt

    NASA Astrophysics Data System (ADS)

    Mary Novena, L.; Suresh Kumar, S.; Athimoolam, S.; Saminathan, K.; Sridhar, B.

    2017-04-01

    The crystal structure of Theophylline (TH) and Theophyillinium chloride monohydrate (THC) and its complete molecular structure analysis on theoretical and experimental methods is reported here. The hydrogen bonding studies were carried out as a special note of the present work. The electron density analyses of the compounds were also analyzed in view of the intermolecular interactions. Moreover, it is an ever first quantum chemical report of this drug (TH) and its chloride salt. In TH crystal, the water molecule connects the Theophylline molecules through Osbnd H⋯N hydrogen bond forming discrete D22(7) motif and dimeric ring R22(10) motif through Nsbnd H⋯O hydrogen bond. In THC, the two classical (Nsbnd H⋯O, Nsbnd H⋯Cl) and one non-classical (Csbnd H⋯O) hydrogen bonds produce two pentameric chain C55 (16) and C55(17) motifs. These two chain motifs are interconnected by Osbnd H⋯O hydrogen bond and cross linked by Nsbnd H⋯Cl and Osbnd H⋯Cl hydrogen bonds to produce octametric ring R88(27) and R88(28) motifs. The solubility test is carried out to enhance the drug solubility and the therapeutic effectiveness of the drug. Experimentally obtained vibrational wavenumbers are compared with the spectra obtained theoretically for both the compound. The strong intensity bands and the shifting of bands due to intermolecular hydrogen bonds are also investigated. The Mulliken atomic charges, HOMO-LUMO and thermodynamic properties are calculated using Density Functional Theory (DFT) and Hartree-Fock Theory (HF) using 6-311++G(d,p) basis set.

  20. Use of alkali metal salts to prepare high purity single-walled carbon nanotube solutions and thin films

    NASA Astrophysics Data System (ADS)

    Ashour, Rakan F.

    Single-walled carbon nanotubes (SWCNTs) display interesting electronic and optical properties desired for many advanced thin film applications, such as transparent conductive electrodes or thin-film transistors. Large-scale production of SWCNTs generally results in polydispersed mixtures of nanotube structures. Since SWCNT electronic character (conducting or semiconducting nature) depends on the nanotube structure, application performance is being held back by this inability to discretely control SWCNT synthesis. Although a number of post-production techniques are able to separate SWCNTs based on electronic character, diameter, or chirality, most still suffer from the disadvantage of high costs of materials, equipment, or labor intensity to be relevant for large-scale production. On the other hand, chromatographic separation has emerged as a method that is compatible with large scale separation of metallic and semiconducting SWCNTs. In this work, SWCNTs, in an aqueous surfactant suspension of sodium dodecyl sulfate (SDS), are separated by their electronic character using a gel chromatography process. Metallic SWCNTs (m-SWCNTs) are collected as initial fractions since they show minimum interaction with the gel medium, whereas, semiconducting SWCNTs (sc- SWCNTs) remain adsorbed to the gel. The process of sc-SWCNT retention in the gel is found to be driven by the packing density of SDS around the SWCNTs. Through a series of separation experiments, it is shown that sc-SWCNTs can be eluted from the gel simply by disturbing the configuration of the SDS/SWCNT micellar structure. This is achieved by either introducing a solution containing a co-surfactant, such as sodium cholate (SC), or solutions of alkali metal ionic salts. Analysis of SWCNT suspensions by optical absorption provides insights into the effect of changing the metal ion (M+ = Li+, Na+, and K+) in the eluting solution. Salts with smaller metal ions (e.g. Li+) require higher concentrations to achieve

  1. Cellulose aerogels prepared from an aqueous zinc chloride salt hydrate melt.

    PubMed

    Schestakow, Maria; Karadagli, Ilknur; Ratke, Lorenz

    2016-02-10

    Monolithic cellulose aerogels are prepared using a salt hydrate melt based on cheap zinc chloride tetrahydrate (ZnCl2·4H2O) that can be washed out of the wet gel-body by using common solvents such as water, ethanol, isopropanol or acetone. Cellulose aerogels with concentrations of 1-5 wt.% cellulose were produced. These aerogels are characterized with respect to shrinkage, density and surface area as well as mechanical properties and micro-structure via SEM. Cellulose aerogels regenerated in acetone show a specific surface area of around 340 m(2)g(-1) being 60% higher than those regenerated in water. The onset of irreversible plastic deformation under compressive load is around 0.8 MPa for acetone-regenerated aerogels and thus a factor of two larger compared to ethanol regenerated ones. The Young's modulus depends almost linearly on the cellulose concentration which is observed for all regenerative fluids with the exception of water. The results achieved are presented in light of the polarity and ability of solvation of ZnCl2·4H2O in the regenerative fluids used.

  2. The ClC-K2 Chloride Channel Is Critical for Salt Handling in the Distal Nephron.

    PubMed

    Hennings, J Christopher; Andrini, Olga; Picard, Nicolas; Paulais, Marc; Huebner, Antje K; Cayuqueo, Irma Karen Lopez; Bignon, Yohan; Keck, Mathilde; Cornière, Nicolas; Böhm, David; Jentsch, Thomas J; Chambrey, Régine; Teulon, Jacques; Hübner, Christian A; Eladari, Dominique

    2017-01-01

    Chloride transport by the renal tubule is critical for blood pressure (BP), acid-base, and potassium homeostasis. Chloride uptake from the urinary fluid is mediated by various apical transporters, whereas basolateral chloride exit is thought to be mediated by ClC-Ka/K1 and ClC-Kb/K2, two chloride channels from the ClC family, or by KCl cotransporters from the SLC12 gene family. Nevertheless, the localization and role of ClC-K channels is not fully resolved. Because inactivating mutations in ClC-Kb/K2 cause Bartter syndrome, a disease that mimics the effects of the loop diuretic furosemide, ClC-Kb/K2 is assumed to have a critical role in salt handling by the thick ascending limb. To dissect the role of this channel in detail, we generated a mouse model with a targeted disruption of the murine ortholog ClC-K2. Mutant mice developed a Bartter syndrome phenotype, characterized by renal salt loss, marked hypokalemia, and metabolic alkalosis. Patch-clamp analysis of tubules isolated from knockout (KO) mice suggested that ClC-K2 is the main basolateral chloride channel in the thick ascending limb and in the aldosterone-sensitive distal nephron. Accordingly, ClC-K2 KO mice did not exhibit the natriuretic response to furosemide and exhibited a severely blunted response to thiazide. We conclude that ClC-Kb/K2 is critical for salt absorption not only by the thick ascending limb, but also by the distal convoluted tubule.

  3. Improved thermoelectric performance of p-type polycrystalline bismuth telluride via hydrothermal treatment with alkali metal salts

    NASA Astrophysics Data System (ADS)

    Su, Zhe

    The field of thermoelectric research has attracted a lot of interest in hope of helping address the energy crisis. In recent years, low-dimensional thermoelectric materials have been found promising and thus become a popular school of thought. However, the high complexity and cost for fabricating low-dimensional materials give rise to the attempt to further improve conventional bulk polycrystalline materials. Polycrystals are featured by numerous grain boundaries that can scatter heat-carrying phonons to significantly reduce the thermal conductivity kappa whereas at the same time can unfortunately deteriorate the electrical resistivity rho. Aiming at the dualism of the grain boundaries in determining the transport properties of polycrystalline materials, a novel concept of "grain boundary engineering" has been proposed in order to have a thermoelectrically favorable grain boundary. In this dissertation, a polycrystalline p-type Bi2Te 3 system has been intensively investigated in light of such a concept that was realized through a hydrothermal nano-coating treatment technique. P-type Bi0.4Sb1.6Te3 powder was hydrothermally treated with alkali metal salt XBH4 ( X = Na, K or Rb) solution. After the treatment, there formed an alkali-metal-containing surface layer of nanometers thick on the p-Bi2Te3 grains. The Na-treatment, leaving the Seebeck coefficient alpha almost untouched, lowered kappa the most while the Rb-treatment at the same time increased alpha slightly and decreased rho the most. Compared to the untreated sample, Na- and Rb-treatments improved the dimensionless figure of merit ZT by ˜ 30% due to the reduced kappa and ˜ 38% owing to the improved the power factor PF, respectively. The grain boundary phase provides a new avenue by which one can potentially decouple the otherwise inter-related alpha, rho and kappa within one thermoelectric material. The morphologic investigation showed this surface layer lacked crystallinity, if any, and was possibly an

  4. Laminar iridium coating produced by pulse current electrodeposition from chloride molten salt

    NASA Astrophysics Data System (ADS)

    Zhu, Li'an; Bai, Shuxin; Zhang, Hong; Ye, Yicong

    2013-10-01

    Due to the unique physical and chemical properties, Iridium (Ir) is one of the most promising oxidation-resistant coatings for refractory materials above 1800 °C in aerospace field. However, the Ir coatings prepared by traditional methods are composed of columnar grains throughout the coating thickness. The columnar structure of the coating is considered to do harm to its oxidation resistance. The laminar Ir coating is expected to have a better high-temperature oxidation resistance than the columnar Ir coating does. The pulse current electrodeposition, with three independent parameters: average current density (Jm), duty cycle (R) and pulse frequency (f), is considered to be a promising method to fabricate layered Ir coating. In this study, laminar Ir coatings were prepared by pulse current electrodeposition in chloride molten salt. The morphology, roughness and texture of the coatings were determined by scanning electron microscope (SEM), profilometer and X-ray diffraction (XRD), respectively. The results showed that the laminar Ir coatings were composed of a nucleation layer with columnar structure and a growth layer with laminar structure. The top surfaces of the laminar Ir coatings consisted of cauliflower-like aggregates containing many fine grains, which were separated by deep grooves. The laminar Ir coating produced at the deposition condition of 20 mA/cm2 (Jm), 10% (R) and 6 Hz (f) was quite smooth (Ra 1.01 ± 0.09 μm) with extremely high degree of preferred orientation of <1 1 1>, and its laminar structure was well developed with clear boundaries and uniform thickness of sub-layers.

  5. Ion Partitioning at the liquid/vapor interface of a multi-component alkali halidesolution: A model for aqueous sea salt aerosols

    SciTech Connect

    Ghosal, Sutapa; Brown, Matthew A.; Bluhm, Hendrik; Krisch, Maria J.; Salmeron, Miquel; Jungwirth, Pavel; Hemminger, John C.

    2008-12-22

    The chemistry of Br species associated with sea salt ice and aerosols has been implicated in the episodes of ozone depletion reported at Arctic sunrise. However, Br{sup -} is only a minor component in sea salt, which has a Br{sup -}/Cl{sup -} molar ratio of {approx}0.0015. Sea salt is a complex mixture of many different species, with NaCl as the primary component. In recent years experimental and theoretical studies have reported enhancement of the large, more polarizable halide ion at the liquid/vapor interface of corresponding aqueous alkali halide solutions. The proposed enhancement is likely to influence the availability of sea salt Br{sup -} for heterogeneous reactions such as those involved in the ozone depletion episodes. We report here ambient pressure x-ray photoelectron spectroscopy studies and molecular dynamics simulations showing direct evidence of Br{sup -} enhancement at the interface of an aqueous NaCl solution doped with bromide. The experiments were carried out on samples with Br{sup -}/Cl{sup -} ratios in the range 0.1% to 10%, the latter being also the ratio for which simulations were carried out. This is the first direct measurement of interfacial enhancement of Br{sup -} in a multi-component solution with particular relevance to sea salt chemistry.

  6. Sodium chloride crystallization from drying drops of albumin-salt solutions with different albumin concentrations

    NASA Astrophysics Data System (ADS)

    Yakhno, T. A.

    2015-11-01

    The salt nature of crystalline structures resulting from drying albumin-salt solutions with a low (<1 wt %) and high (7 and 9 wt %) concentration of albumin and a NaCl concentration kept at a physiological level (0.9 wt %) is experimentally substantiated. Such a conclusion is drawn from the dynamics of phase transitions, morphological studies, and differences between the physicochemical properties of albumin and salt. Obtained data give a deeper insight into the albumin and salt distributions in drying liquids.

  7. Salt crust development in paddy fields owing to soil evaporation and drainage: Contribution of chloride and deuterium profile analysis

    NASA Astrophysics Data System (ADS)

    Grünberger, Olivier; Macaigne, Peggy; Michelot, Jean-Luc; Hartmann, Christian; Sukchan, Somsak

    2008-01-01

    SummaryIn Northeast Thailand lowlands with shallow saline watertable, rainfed paddy fields often present high salt concentration in the dry season, forming patches or spots of salt crusts on the soil surface. In this context, the mechanisms implied in salt concentration during dry season were studied by establishing salt budget with evaporation and drainage estimates inside and outside a saline patch. Drainage was estimated by Hydrus-1D modelling constrained by an hydrodynamic characterization and the profile of water contents at the end of dry season. Evaporation rates at the end of the dry season were computed by interpreting natural detailed profiles of deuterium (D) and chloride (Cl) contents. Because of the drastic diminution of hydraulic conductivity at saturation with depth and the decrease of groundwater level at the end of the cropping season, simulated hydrological balance with Hydrus-1D pointed out zero cumulated fluxes for depths of 39.5 cm (outside the saline patch) and 37.5 cm (inside the saline patch). Therefore, all the chloride accumulated in the very upper layers during dry season comes from the chloride that was present in the 0-39.5 cm layers before the beginning of the drying. Inside the saline patch, the tentative Cl budget is coherent with the hypothesis of saturation of the profile by aquifer saline water during the flooding. Evaporation rates computed from the diffusion of chloride and deuterium at the end of the drying season, when the aquifer level was 1.4 m deep, range between 0.121 and 0.378 mm d -1. This does not sustain the assumption of a considerable salinity contribution from the aquifer during the dry season. Moreover, evaporation estimates based on Cl and D diffusion equilibrium showed depleted rates (38-63%) inside the saline patch due to salt accumulation in the first 12 cm of the soil. In the vapour transfer layer, estimated evaporation rate based on the vapour movement of D was in the same order of magnitude than computed

  8. Fast synthesis and single crystal growth of Pb-free and Pb-doped Bi-2223 superconductors using alkali chlorides flux technique

    NASA Astrophysics Data System (ADS)

    Lee, S.; Yamamoto, A.; Tajima, S.

    2001-09-01

    Here we report our recent results for the fast synthesis of Bi 2Sr 2Ca 2Cu 3O 10+ x phase in powder and single crystal forms using modified alkali chlorides flux technique. For many factors such as flux, crucibles materials, chemical and phase composition of the precursor, temperature and duration of heat treatment, evaporation rate of the flux, their effects on the formation and growth of 2223 have been studied. By optimization of these parameters, the single-phase samples of Pb-doped and Pb-free 2223 phase were obtained in the temperature range of 850-870°C and heat treatment for <15 h, that is much faster, compared with a solid-state reaction technique. The single crystals with the size of 0.5 mm were isolated and characterized using XRD, SEM/EDX, susceptibility and resistivity measurements. The effect of post-annealing in different atmospheres on the oxygen content and superconductivity of the samples was studied by TG and chemical analyses.

  9. Structures and heats of formation of simple alkali metal compounds: hydrides, chlorides, fluorides, hydroxides, and oxides for Li, Na, and K.

    PubMed

    Vasiliu, Monica; Li, Shenggang; Peterson, Kirk A; Feller, David; Gole, James L; Dixon, David A

    2010-04-01

    Geometry parameters, frequencies, heats of formation, and bond dissociation energies are predicted for simple alkali metal compounds (hydrides, chlorides, fluorides, hydroxides and oxides) of Li, Na, and K from coupled cluster theory [CCSD(T)] calculations including core-valence correlation with the aug-cc-pwCVnZ basis set (n = D, T, Q, and 5). To accurately calculate the heats of formation, the following additional correction were included: scalar relativistic effects, atomic spin-orbit effects, and vibrational zero-point energies. For calibration purposes, the properties of some of the lithium compounds were predicted with iterative triple and quadruple excitations via CCSDT and CCSDTQ. The calculated geometry parameters, frequencies, heats of formation, and bond dissociation energies were compared with all available experimental measurements and are in excellent agreement with high-quality experimental data. High-level calculations are required to correctly predict that K(2)O is linear and that the ground state of KO is (2)Sigma(+), not (2)Pi, as in LiO and NaO. This reliable and consistent set of calculated thermodynamic data is appropriate for use in combustion and atmospheric simulations.

  10. Evaluating the effectiveness of adding magnesium chloride to conventional protocol of citrate alkali therapy on kidney stone size

    PubMed Central

    Niroomand, Hassan; Ziaee, Amin; Ziaee, Keivan; Gheissari, Alaleh

    2016-01-01

    Background: Potassium citrate (K-Cit) is one of the therapeutic solutions broadly used in patients with urolithiasis. However, recent studies have shown that it is not so effective. Therefore, the goal of our study was to evaluate the effect of a combination of K-Cit - MgCl2 oral supplements, on urinary stone size. Materials and Methods: This study was performed on 70 asymptomatic urolithiasis cases. The supplements included K-Cit and magnesium chloride (MgCl2), purchased from (Merck Company, Germany). The patients were randomly divided into two groups. The urinary stone size was measured in the control group after prescribing K-Cit alone and the treated group with combination of K-Cit and MgCl2 for 4 weeks by ultrasonography and also urinary parameter was measured in each groups. Results: The mean age of patients was 16.26 ± 5.70 years. Hyperoxaluria and hypercalciuria were seen in 70% and 52% of patients, respectively. Initially, the mean urinary stone size was measured in each groups and there is not any significant different. However, we find a significant decrease in urinary stone size in group which is treated with combination of K-Cit and MgCl2 for 4 weeks in comparison with control group treated with K-Cit alone in the same duration of therapeutic course (5.1 ± 0.8 vs. 2.5 ± 1.2, P < 0.05). All ultrasonography were performed by one radiologist and device. Conclusion: Our results suggested that a combination of K-Cit and MgCl2 chloride is more effective on decreasing urinary stone size than K-Cit alone. PMID:27995107

  11. Analysis of the corrosion of carbon steels in simulated salt repository brines and acid chloride solutions at high temperatures

    SciTech Connect

    Diercks, D.R.; Kassner, T.F.

    1988-04-01

    An analysis of literature data on the corrosion of carbon steels in anoxic brines and acid chloride solutions was performed, and the results were used to assess the expected life of high-level nuclear waste package containers in a salt repository environment. The corrosion rate of carbon steels in moderately acidic aqueous chloride environments obeys an Arrhenius dependence on temperature and a (pH{sub 2}){sup {minus}1/2} dependence on hydrogen partial pressure. The cathodic reduction of water to produce hydrogen is the rate-controlling step in the corrosion process. An expression for the corrosion rate incorporating these two dependencies was used to estimate the corrosion life of several proposed waste package configurations. 42 refs., 11 figs., 2 tabs.

  12. Breadboard wash water renovation system. [using ferric chloride and ion exchange resins to remove soap and dissolved salts

    NASA Technical Reports Server (NTRS)

    1978-01-01

    A total wash water renovation system concept was developed for removing objectionable materials from spacecraft wash water in order to make the water reusable. The breadboard model system described provides for pretreatment with ferric chloride to remove soap by chemical precipitation, carbon adsorption to remove trace dissolved organics, and ion exchange for removal of dissolved salts. The entire system was put into continuous operation and carefully monitored to assess overall efficiency and equipment maintenance problems that could be expected in actual use. In addition, the capacity of the carbon adsorbers and the ion-exchange resin was calculated and taken into consideration in the final evaluation of the system adequacy. The product water produced was well within the Tentative Wash Water Standards with regard to total organic carbon, conductivity, urea content, sodium chloride content, color, odor, and clarity.

  13. Potential of salt-accumulating and salt-secreting halophytic plants for recycling sodium chloride in human urine in bioregenerative life support systems

    NASA Astrophysics Data System (ADS)

    Tikhomirova, N. A.; Ushakova, S. A.; Kudenko, Yu. A.; Gribovskaya, I. V.; Shklavtsova, E. S.; Balnokin, Yu. V.; Popova, L. G.; Myasoedov, N. A.; Gros, J.-B.; Lasseur, Ch.

    2011-07-01

    This study addresses the possibility of growing different halophytic plants on mineralized human urine as a way to recycle NaCl from human wastes in a bioregenerative life support system (BLSS). Two halophytic plant species were studied: the salt-accumulating Salicornia europaea and the salt-secreting Limonium gmelinii. During the first two weeks, plants were grown on Knop's solution, then an average daily amount of urine produced by one human, which had been preliminarily mineralized, was gradually added to the experimental solutions. Nutrient solutions simulating urine mineral composition were gradually added to control solutions. NaCl concentrations in the stock solutions added to the experimental and control solutions were 9 g/L in the first treatment and 20 g/L in the second treatment. The mineralized human urine showed some inhibitory effects on S. europaea and L. gmelinii. The biomass yield of experimental plants was lower than that of control ones. If calculated for the same time period (120 d) and area (1 m 2), the amount of sodium chloride taken up by S. europaea plants would be 11.7 times larger than the amount taken up by L. gmelinii plants (486 g/m 2 vs. 41 g/m 2). Thus, S. europaea is the better choice of halophyte for recycling sodium chloride from human wastes in BLSS.

  14. Damage development, phase changes, transport properties, and freeze-thaw performance of cementitious materials exposed to chloride based salts

    NASA Astrophysics Data System (ADS)

    Farnam, Yaghoob

    Recently, there has been a dramatic increase in premature deterioration in concrete pavements and flat works that are exposed to chloride based salts. Chloride based salts can cause damage and deterioration in concrete due to the combination of factors which include: increased saturation, ice formation, salt crystallization, osmotic pressure, corrosion in steel reinforcement, and/or deleterious chemical reactions. This thesis discusses how chloride based salts interact with cementitious materials to (1) develop damage in concrete, (2) create new chemical phases in concrete, (3) alter transport properties of concrete, and (4) change the concrete freeze-thaw performance. A longitudinal guarded comparative calorimeter (LGCC) was developed to simultaneously measure heat flow, damage development, and phase changes in mortar samples exposed to sodium chloride (NaCl), calcium chloride (CaCl 2), and magnesium chloride (MgCl2) under thermal cycling. Acoustic emission and electrical resistivity measurements were used in conjunction with the LGCC to assess damage development and electrical response of mortar samples during cooling and heating. A low-temperature differential scanning calorimetry (LT-DSC) was used to evaluate the chemical interaction that occurs between the constituents of cementitious materials (i.e., pore solution, calcium hydroxide, and hydrated cement paste) and salts. Salts were observed to alter the classical phase diagram for a salt-water system which has been conventionally used to interpret the freeze-thaw behavior in concrete. An additional chemical phase change was observed for a concrete-salt-water system resulting in severe damage in cementitious materials. In a cementitious system exposed to NaCl, the chemical phase change occurs at a temperature range between -6 °C and 8 °C due to the presence of calcium sulfoaluminate phases in concrete. As a result, concrete exposed to NaCl can experience additional freeze-thaw cycles due to the chemical

  15. Bromination of aromatic compounds by residual bromide in sodium chloride matrix modifier salt during heated headspace GC/MS analysis.

    PubMed

    Fine, Dennis D; Ko, Saebom; Huling, Scott

    2013-12-15

    Analytical artifacts attributed to the bromination of toluene, xylenes, and trimethylbenzenes were found during the heated headspace gas chromatography/mass spectrometry (GC/MS) analysis of aqueous samples. The aqueous samples were produced from Fenton-like chemical oxidation reactions and contained aromatic compounds, hydrogen peroxide (H2O2), and ferric sulfate. Prior to GC/MS headspace analysis, the samples were acidified (pH<2), and sodium chloride was amended to the headspace vial as a matrix modifier. The brominated artifacts were generated during heated headspace analysis. Further, when samples were spiked with a mixture of volatile chlorinated and aromatic compounds (50 µg/L), poor spike recoveries of toluene and xylenes occurred, and in some cases complete loss of trimethylbenzenes and naphthalene resulted. Where poor recovery of aromatic spike compounds occurred, brominated aromatic compounds were found. The only significant source of bromine in the reaction scheme is the bromide typically present (<0.01% w/w) in the sodium chloride amended to the samples. Conversely, brominated artifacts were absent when a buffered salt mixture composed of sodium chloride and potassium phosphate dibasic/monobasic was used as a matrix modifier and raised the sample pH (pH~6). This indicated that the brominated artifacts resulted from the reaction of the aromatic compounds with BrCl, which was formed by the reaction of H2O2, chloride, and bromide under acidic conditions. An alternative matrix modifier salt is recommended that prevents the bromination reaction and avoids these deleterious effects on sample integrity during headspace analysis.

  16. Electrolytic method to make alkali alcoholates using ion conducting alkali electrolyte/separator

    DOEpatents

    Joshi, Ashok V [Salt Lake City, UT; Balagopal, Shekar [Sandy, UT; Pendelton, Justin [Salt Lake City, UT

    2011-12-13

    Alkali alcoholates, also called alkali alkoxides, are produced from alkali metal salt solutions and alcohol using a three-compartment electrolytic cell. The electrolytic cell includes an anolyte compartment configured with an anode, a buffer compartment, and a catholyte compartment configured with a cathode. An alkali ion conducting solid electrolyte configured to selectively transport alkali ions is positioned between the anolyte compartment and the buffer compartment. An alkali ion permeable separator is positioned between the buffer compartment and the catholyte compartment. The catholyte solution may include an alkali alcoholate and alcohol. The anolyte solution may include at least one alkali salt. The buffer compartment solution may include a soluble alkali salt and an alkali alcoholate in alcohol.

  17. Electrolyte salts for power sources

    DOEpatents

    Doddapaneni, N.; Ingersoll, D.

    1995-11-28

    Electrolyte salts are disclosed for power sources comprising salts of phenyl polysulfonic acids and phenyl polyphosphonic acids. The preferred salts are alkali and alkaline earth metal salts, most preferably lithium salts. 2 figs.

  18. Electrolyte salts for power sources

    DOEpatents

    Doddapaneni, Narayan; Ingersoll, David

    1995-01-01

    Electrolyte salts for power sources comprising salts of phenyl polysulfonic acids and phenyl polyphosphonic acids. The preferred salts are alkali and alkaline earth metal salts, most preferably lithium salts.

  19. Preparation of fused chloride salts for use in pyrochemical plutonium recovery operations at Los Alamos

    SciTech Connect

    Fife, K.W.; Bowersox, D.F.; Christensen, D.C.; Williams, J.D.

    1986-07-01

    The Plutonium Metal Technology Group at Los Alamos routinely uses pyrochemical processes to produce and purify plutonium from impure sources. The basic processes (metal production, metal purification, and residue treatment) involve controlling oxidation and reduction reactions between plutonium and its compounds in molten salts. Current production methods are described, as well as traditional approaches and recent developments in the preparation of solvent salts for electrorefining, molten salt extraction, lean metal (pyroredox) purification, and direct oxide reduction.

  20. The influence of fluoride ions on the equilibrium between titanium ions and titanium metal in fused alkali chloride melts.

    PubMed

    Song, Jianxun; Wang, Qiuyu; Wu, Jinyu; Jiao, Shuqiang; Zhu, Hongmin

    2016-08-15

    KF is employed as a source of fluoride ions added to the melt to disclose the influence of fluoride on the disproportionation reactions of titanium ions, 3Ti(2+) = 2Ti(3+) + Ti, and 4Ti(3+) = 3Ti(4+) + Ti. The results reveal that the equilibrium transferred to the right direction for the first reaction and the apparent equilibrium constant increased sharply, mainly because of the formation of coordination compounds: TiFi(3-i). The accurate values of the equilibrium constants referring to the formation reactions of Ti(3+) + iF(-) = TiFi(3-i) (i = 1-6) in NaCl-KCl melt at 1023 K were evaluated with a best fit least squares method. It is also revealed that the stable states of the coordination compounds are TiF(2+), TiF2(+), TiF4(-) and TiF6(3-). Moreover, the Gibbs free energies for complex formation were estimated. Ti(2+) was undetectable when the concentration of fluoride ion was high enough. The equilibrium constant for the formation reaction, Ti(4-) + 6F(-) = TiF6(2-), was evaluated. The equilibrium constant, Kc2, for the disproportionation reaction 4Ti(3+) = 3Ti(4+) + Ti, in chloride melt was determined as 0.015.

  1. Chemical compositions of sulfate and chloride salts over the last termination reconstructed from the Dome Fuji ice core, inland Antarctica

    NASA Astrophysics Data System (ADS)

    Oyabu, Ikumi; Iizuka, Yoshinori; Uemura, Ryu; Miyake, Takayuki; Hirabayashi, Motohiro; Motoyama, Hideaki; Sakurai, Toshimitsu; Suzuki, Toshitaka; Hondoh, Takeo

    2014-12-01

    The flux and chemical composition of aerosols impact the climate. Antarctic ice cores preserve the record of past atmospheric aerosols, providing useful information about past atmospheric environments. However, few studies have directly measured the chemical composition of aerosol particles preserved in ice cores. Here we present the chemical compositions of sulfate and chloride salts from aerosol particles in the Dome Fuji ice core. The analysis method involves ice sublimation, and the period covers the last termination, 25.0-11.0 thousand years before present (kyr B.P.), with a 350 year resolution. The major components of the soluble particles are CaSO4, Na2SO4, and NaCl. The dominant sulfate salt changes at 16.8 kyr B.P. from CaSO4, a glacial type, to Na2SO4, an interglacial type. The sulfate salt flux (CaSO4 plus Na2SO4) inversely correlates with δ18O in Dome Fuji over millennial timescales. This correlation is consistent with the idea that sulfate salt aerosols contributed to the last deglacial warming of inland Antarctica by reducing the aerosol indirect effect. Between 16.3 and 11.0 kyr B.P., the presence of NaCl suggests that winter atmospheric aerosols are preserved. A high NaCl/Na2SO4 fraction between 12.3 and 11.0 kyr B.P. indicates that the contribution from the transport of winter atmospheric aerosols increased during this period.

  2. Potassium nitrate application alleviates sodium chloride stress in winter wheat cultivars differing in salt tolerance.

    PubMed

    Zheng, Yanhai; Jia, Aijun; Ning, Tangyuan; Xu, Jialin; Li, Zengjia; Jiang, Gaoming

    2008-09-29

    A sand culture experiment was conducted to answer the question whether or not exogenous KNO(3) can alleviate adverse effects of salt stress in winter wheat by monitoring plant growth, K(+)/Na(+) accumulation and the activity of some antioxidant enzymes. Seeds of two wheat cultivars (CVs), DK961 (salt-tolerant) and JN17 (salt-sensitive), were planted in sandboxes and controls germinated and raised with Hoagland nutrient solution (6 mM KNO(3), no NaCl). Experimental seeds were exposed to seven modified Hoagland solutions containing increased levels of KNO(3) (11, 16, 21 mM) or 100 mM NaCl in combination with the four KNO(3) concentrations (6, 11, 16 and 21 mM). Plants were harvested 30 d after imbibition, with controls approximately 22 cm in height. Both CVs showed significant reduction in plant height, root length and dry weight of shoots and roots under KNO(3) or NaCl stress. However, the combination of increased KNO(3) and NaCl alleviated symptoms of the individual salt stresses by improving growth of shoots and roots, reducing electrolyte leakage, malondialdehyde and soluble sugar contents and enhancing the activities of antioxidant enzymes. The salt-tolerant cultivar accumulated more K(+) in both shoots and roots compared with the higher Na(+) accumulation typical for the salt-sensitive cultivar. Soluble sugar content and activities of antioxidant enzymes were found to be more stable in the salt-tolerant cultivar. Our findings suggest that the optimal K(+)/Na(+) ratio of the nutrient solution should be 16:100 for both the salt-tolerant and the salt-sensitive cultivar under the experimental conditions used, and that the alleviation of NaCl stress symptoms through simultaneously applied elevated KNO(3) was more effective in the salt-tolerant than in the salt-sensitive cultivar.

  3. Reactivity of NaCl with Secondary Organic Acids: An Important Mechanism of the Chloride Depletion in Sea Salt Particles Mixed with Organic Materials

    NASA Astrophysics Data System (ADS)

    Wang, B.; Laskin, A.; Kelly, S.; Gilles, M. K.; Shilling, J. E.; Zelenyuk, A.; Wilson, J. M.; Tivanski, A.

    2012-12-01

    Sea salt particles, one of the major sources of atmospheric aerosols, undergo complex multi-phase reactions and have profound consequences on their physical and chemical properties, thus on climate. Depletion of chloride in sea salt particles was reported in previous field studies and was attributed to the acid displacement of sea salt chlorides with inorganic acids, such as nitric and sulfuric acids. Some studies have also showed that the chloride deficit cannot be fully compensated for this mechanism. We present an important pathway contributing to this chloride depletion: reactions of weak organic acids with sea salt particles. NaCl particles internally mixed with secondary organic materials generated from the reactions of limonene and alpha-pinene with ozone served as surrogates for sea salt particles mixed with organic materials. Chemical imaging analysis of these particles was conducted using complementary techniques including computer controlled scanning electron microscopy with energy dispersive analysis of X-rays (CCSEM/EDX), scanning transmission X-ray microscopy with near edge X-ray absorption fine structure spectroscopy (STXM/NEXAFS), and micro-fourier transform infrared spectroscopy (micro-FTIR). Substantial chloride depletion and formation of organic salts were observed along with distinctive changes in particle morphology after hydration/dehydration processes. The results indicate that secondary organic acids can effectively react with NaCl particles resulting in displacement of chloride and release of gaseous HCl. This is consistent with a recent field study showing chloride depletion in sea salt particles mixed with organic materials which cannot be fully compensated by inorganic acid displacement. Although the formation of the organic salts is not thermodynamically favored in bulk aqueous solution, these reactions are driven by the high volatility and evaporation of gaseous HCl in particles, especially during hydration/dehydration processes. The

  4. Chloride dynamics in a restored urban stream and the influence of road salts on water quality

    EPA Science Inventory

    Understanding the connection between road salts and water quality is essential to assess the implications for human health and ecosystem services from these widely used de-icers. Preliminary analysis identified a probable connection between road salt application and a stream wat...

  5. The relationship between molecular structure and biological activity of alkali metal salts of vanillic acid: Spectroscopic, theoretical and microbiological studies

    NASA Astrophysics Data System (ADS)

    Świsłocka, Renata; Piekut, Jolanta; Lewandowski, Włodzimierz

    In this paper we investigate the relationship between molecular structure of alkali metal vanillate molecules and their antimicrobial activity. To this end FT-IR, FT-Raman, UV absorption and 1H, 13C NMR spectra for lithium, sodium, potassium, rubidium and caesium vanillates in solid state were registered, assigned and analyzed. Microbial activity of studied compounds was tested against Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus, Proteus vulgaris, Bacillus subtilis and Candida albicans. In order to evaluate the dependence between chemical structure and biological activity of alkali metal vanillates the statistical analysis was performed for selected wavenumbers from FT-IR spectra and parameters describing microbial activity of vanillates. The geometrical structures of the compounds studied were optimized and the structural characteristics were determined by density functional theory (DFT) using at B3LYP method with 6-311++G** as basis set. The obtained statistical equations show the existence of correlation between molecular structure of vanillates and their biological properties.

  6. Salting-out solvent extraction for the off-line preconcentration of benzalkonium chloride in capillary electrophoresis.

    PubMed

    So, T S; Huie, C W

    2001-07-01

    The use of salting-out effect for the off-line preconcentration of charged analytes in capillary electrophoresis is demonstrated for the first time. Using benzalkonium chloride (BAK) as model compound, a mixture of cationic surfactants consisting of even-numbered alkylbenzyl quaternary ammonium homologues (C8-C18), the addition of appropriate amounts of sodium chloride and acetonitrile in the sample solution (2 mL sample volume) was found to be capable of providing ca. 40-fold enhancement in detection sensitivity. In addition to affording a preconcentrating effect due to the extraction of BAK in the smaller volume water-miscible organic solvent phase (acetonitrile), the organic solvent also serves to improve the peak area and shape of the longer chain surfactants. Optimal experimental conditions, such as volume of acetonitrile and concentration of sodium chloride, for the preconcentration of BAK with good preconcentration factors and reproducibility were investigated. The usefulness of the present method was demonstrated for the improved determination of BAK present in commercially available industrial and pharmaceutical products.

  7. Effect of moisture on corrosion of Ni-based alloys in molten alkali fluoride FLiNaK salt environments

    NASA Astrophysics Data System (ADS)

    Ouyang, Fan-Yi; Chang, Chi-Hung; You, Bo-Chien; Yeh, Tsung-Kuang; Kai, Ji-Jung

    2013-06-01

    We investigated the corrosion characteristics on several selected alloys at 600 and 700 °C in FLiNaK molten salts with different moisture contents. Hastelloys-N and Hastelloys-B3 exhibited better corrosion resistances, while Haynes 263 showed the poorest corrosion resistance. The mass loss of the tested alloys is primarily determined by the purity of FLiNaK salts; however, the effect of temperature becomes more important on the mass loss of the tested alloys in the non-purified FLiNaK salts. When the residual moisture is present in the FLiNaK salts, the mass losses of the tested alloys varied linearly with original Cr content plus one-third of Mo content. The results of structural characterization revealed that the tested alloys in the FLiNaK salts with higher moisture content would aggravate intergranular corrosion and pitting.

  8. The effect of ferrocyanide ions on sodium chloride crystallization in salt mixtures

    NASA Astrophysics Data System (ADS)

    Gupta, Sonia; Pel, Leo; Steiger, Michael; Kopinga, Klaas

    2015-01-01

    The use of crystallization inhibitors has been proposed as a potential preventive treatment method against damage and is extensively tested for crystallization of single salts. However, in practice salt mixtures are present. Therefore, before using inhibitors in practice there is a strong need to explore their effect on salt mixtures. In this research, we studied the effect of ferrocyanide ions ([Fe(CN)6]4-) on NaCl crystallization in single salt and in salt mixtures of NaCl-KCl and NaCl-LiCl. A series of micro droplet drying experiments were undertaken. Time lapse microscopy of the crystallization was performed along with NMR measurements of hydrogen, sodium and lithium ions. This gives the possibility to visualize the drying of the droplet while simultaneously obtaining information of both NaCl and LiCl concentration in the droplet. For a NaCl solution droplet, in the presence of inhibitor, a significantly higher supersaturation prior to the onset of crystallization and a change in crystal morphology were observed. On the other hand, for salt mixtures, lower supersaturation compared to single salt and dendritic crystal morphology was seen in the presence of inhibitor. In a porous material, such a type of morphology can promote the formation of efflorescence that causes only little structural damage.

  9. Norepinephrine-evoked salt-sensitive hypertension requires impaired renal sodium chloride cotransporter activity in Sprague-Dawley rats.

    PubMed

    Walsh, Kathryn R; Kuwabara, Jill T; Shim, Joon W; Wainford, Richard D

    2016-01-15

    Recent studies have implicated a role of norepinephrine (NE) in the activation of the sodium chloride cotransporter (NCC) to drive the development of salt-sensitive hypertension. However, the interaction between NE and increased salt intake on blood pressure remains to be fully elucidated. This study examined the impact of a continuous NE infusion on sodium homeostasis and blood pressure in conscious Sprague-Dawley rats challenged with a normal (NS; 0.6% NaCl) or high-salt (HS; 8% NaCl) diet for 14 days. Naïve and saline-infused Sprague-Dawley rats remained normotensive when placed on HS and exhibited dietary sodium-evoked suppression of peak natriuresis to hydrochlorothiazide. NE infusion resulted in the development of hypertension, which was exacerbated by HS, demonstrating the development of the salt sensitivity of blood pressure [MAP (mmHg) NE+NS: 151 ± 3 vs. NE+HS: 172 ± 4; P < 0.05]. In these salt-sensitive animals, increased NE prevented dietary sodium-evoked suppression of peak natriuresis to hydrochlorothiazide, suggesting impaired NCC activity contributes to the development of salt sensitivity [peak natriuresis to hydrochlorothiazide (μeq/min) Naïve+NS: 9.4 ± 0.2 vs. Naïve+HS: 7 ± 0.1; P < 0.05; NE+NS: 11.1 ± 1.1; NE+HS: 10.8 ± 0.4). NE infusion did not alter NCC expression in animals maintained on NS; however, dietary sodium-evoked suppression of NCC expression was prevented in animals challenged with NE. Chronic NCC antagonism abolished the salt-sensitive component of NE-mediated hypertension, while chronic ANG II type 1 receptor antagonism significantly attenuated NE-evoked hypertension without restoring NCC function. These data demonstrate that increased levels of NE prevent dietary sodium-evoked suppression of the NCC, via an ANG II-independent mechanism, to stimulate the development of salt-sensitive hypertension.

  10. A simple one-step synthesis of ZnS nanoparticles via salt-alkali-composited-mediated method and investigation on their comparative photocatalytic activity

    SciTech Connect

    Xiang, Donghu; Zhu, Yabo; He, Zhanjun; Liu, Zhangsheng; Luo, Jin

    2013-02-15

    Graphical abstract: The TEM image shows that the as-synthesized ZnS particle size was estimated to be about 40 nm and this newly synthesized ZnS nanoparticles can be as a promising photocatalytic degradation material for the organic pollutant removal. Display Omitted Highlights: ► ZnS nanoparticles with cubic phase have been successfully synthesized via salt-alkali-composited-mediated method (SACM) for the first time and this method has not been found so far. ► Its band gap (E{sub g}) is a little bigger than commercial ZnS particle mainly due to quantum size effect. ► The as-synthesized ZnS nanoparticles show much more efficient photocatalytic degradation on methyl orange than commercial ZnS powder. -- Abstract: ZnS nanoparticles have been successfully synthesized via salt-alkali-composited-mediated method (SACM) for the first time, using a mixture of LiNO{sub 3} and LiOH (LiNO{sub 3}/LiOH = 60.7:39.3) as a reaction solvent, sodium sulfide and zinc nitrate as reactants at temperature of 210 °C for 24 h in the absence of organic dispersant or capping agents. X-ray diffraction, environment scanning electron microscopy (ESEM) and Transmission electron microscopy (TEM) indicated that the as-synthesized products were well crystallized and belonged to nano-scale. Their UV–vis absorption spectrum demonstrated a band gap of 3.6406 eV corresponding to the absorption edge of 340 nm. The experimental result of photocatalytic degradation on methyl orange by the nano-ZnS showed much better photocatalysis than that by the commercial ZnS powder under the irradiation of ultraviolet light and visible light, respectively.

  11. Rapid, easy cyanation of aryl bromides and chlorides using nickel salts in conjunction with microwave promotion.

    PubMed

    Arvela, Riina K; Leadbeater, Nicholas E

    2003-11-14

    We report here a fast, easy, and efficient method for the preparation of aryl nitriles from aryl bromides and chlorides. The methodology for aryl bromides involves the use of either Ni(CN)(2) or NaCN and NiBr(2). With aryl chlorides, a mix of NaCN and NiBr(2) is used and the reaction proceeds via the in situ formation of the corresponding aryl bromide. The reaction can be performed in air and is complete within 10 min.

  12. Glyoxal and Methylglyoxal Setschenow Salting Constants in Sulfate, Nitrate, and Chloride Solutions: Measurements and Gibbs Energies.

    PubMed

    Waxman, Eleanor M; Elm, Jonas; Kurtén, Theo; Mikkelsen, Kurt V; Ziemann, Paul J; Volkamer, Rainer

    2015-10-06

    Knowledge about Setschenow salting constants, KS, the exponential dependence of Henry's Law coefficients on salt concentration, is of particular importance to predict secondary organic aerosol (SOA) formation from soluble species in atmospheric waters with high salt concentrations, such as aerosols. We have measured KS of glyoxal and methylglyoxal for the atmospherically relevant salts (NH4)2SO4, NH4NO3, NaNO3, and NaCl and find that glyoxal consistently "salts-in" (KS of -0.16, -0.06, -0.065, -0.1 molality(-1), respectively) while methylglyoxal "salts-out" (KS of +0.16, +0.075, +0.02, +0.06 molality(-1)). We show that KS values for different salts are additive and present an equation for use in atmospheric models. Additionally, we have performed a series of quantum chemical calculations to determine the interactions between glyoxal/methylglyoxal monohydrate with Cl(-), NO3(-), SO4(2-), Na(+), and NH4(+) and find Gibbs free energies of water displacement of -10.9, -22.0, -22.9, 2.09, and 1.2 kJ/mol for glyoxal monohydrate and -3.1, -10.3, -7.91, 6.11, and 1.6 kJ/mol for methylglyoxal monohydrate with uncertainties of 8 kJ/mol. The quantum chemical calculations support that SO4(2-), NO3(-), and Cl(-) modify partitioning, while cations do not. Other factors such as ion charge or partitioning volume effects likely need to be considered to fully explain salting effects.

  13. EVIDENCE OF CORROSIVE GAS FORMED BY RADIOLYSIS OF CHLORIDE SALTS IN PLUTONIUM-BEARING MATERIALS

    SciTech Connect

    Dunn, K.; Louthan, M.

    2010-02-01

    Corrosion and pitting have been observed in headspace regions of stainless steel containers enclosing plutonium oxide/salt mixtures. These observations are consistent with the formation of a corrosive gas, probably HCl, and transport of that gas to the headspace regions of sealed containers. The NH{sub 4}Cl films found on the walls of the sealed containers is also indicative of the presence of HCl gas. Radiolysis of hydrated alkaline earth salts is the probable source of HCl.

  14. Chlor-Alkali Technology.

    ERIC Educational Resources Information Center

    Venkatesh, S.; Tilak, B. V.

    1983-01-01

    Chlor-alkali technology is one of the largest electrochemical industries in the world, the main products being chlorine and caustic soda (sodium hydroxide) generated simultaneously by the electrolysis of sodium chloride. This technology is reviewed in terms of electrochemical principles and manufacturing processes involved. (Author/JN)

  15. Nano spray-dried sodium chloride and its effects on the microbiological and sensory characteristics of surface-salted cheese crackers.

    PubMed

    Moncada, Marvin; Astete, Carlos; Sabliov, Cristina; Olson, Douglas; Boeneke, Charles; Aryana, Kayanush J

    2015-09-01

    Reducing particle size of salt to approximately 1.5 µm would increase its surface area, leading to increased dissolution rate in saliva and more efficient transfer of ions to taste buds, and hence, perhaps, a saltier perception of foods. This has a potential for reducing the salt level in surface-salted foods. Our objective was to develop a salt using a nano spray-drying method, to use the developed nano spray-dried salt in surface-salted cheese cracker manufacture, and to evaluate the microbiological and sensory characteristics of cheese crackers. Sodium chloride solution (3% wt/wt) was sprayed through a nano spray dryer. Particle sizes were determined by dynamic light scattering, and particle shapes were observed by scanning electron microscopy. Approximately 80% of the salt particles produced by the nano spray dryer, when drying a 3% (wt/wt) salt solution, were between 500 and 1,900 nm. Cheese cracker treatments consisted of 3 different salt sizes: regular salt with an average particle size of 1,500 µm; a commercially available Microsized 95 Extra Fine Salt (Cargill Salt, Minneapolis, MN) with an average particle size of 15 µm; and nano spray-dried salt with an average particle size of 1.5 µm, manufactured in our laboratory and 3 different salt concentrations (1, 1.5, and 2% wt/wt). A balanced incomplete block design was used to conduct consumer analysis of cheese crackers with nano spray-dried salt (1, 1.5, and 2%), Microsized salt (1, 1.5, and 2%) and regular 2% (control, as used by industry) using 476 participants at 1wk and 4mo. At 4mo, nano spray-dried salt treatments (1, 1.5, and 2%) had significantly higher preferred saltiness scores than the control (regular 2%). Also, at 4mo, nano spray-dried salt (1.5 and 2%) had significantly more just-about-right saltiness scores than control (regular 2%). Consumers' purchase intent increased by 25% for the nano spray-dried salt at 1.5% after they were notified about the 25% reduction in sodium content of the

  16. Dietary salt regulates the phosphorylation of OSR1/SPAK kinases and the sodium chloride cotransporter through aldosterone.

    PubMed

    Chiga, Motoko; Rai, Tatemitsu; Yang, Sung-Sen; Ohta, Akihito; Takizawa, Toichiro; Sasaki, Sei; Uchida, Shinichi

    2008-12-01

    Pseudohypoaldosteronism type II (PHAII) is caused by mutations in the WNK1 and WNK4 genes (WNK with-no-lysine kinase). In a mouse model of this disease where a mutant of Wnk4 D561A was knocked in, increased phosphorylation of the sodium chloride cotransporter (NCC) was found and the transporter was concentrated on the apical membrane of the distal tubules. In addition, we recently found that other kinases, such as the oxidative stress response kinase-1/STE20/SPS1-related proline alanine-rich kinase (OSR1/SPAK), also showed increased phosphorylation in these mice. Here we determined whether this kinase cascade is regulated by dietary salt intake. We found that the phosphorylation states of NCC and OSR1/SPAK were increased by low-salt diets and decreased by high-salt diets; a regulation completely lost in the knock-in mice. Increased phosphorylation was reversed by spironolactone and this decreased phosphorylation was reversed by administration of exogenous aldosterone. These studies suggest that that the WNK-OSR1/SPAK-NCC cascade may be a novel effector system of aldosterone action in the kidney.

  17. The role of the binding salt sodium salicylate in semidilute ionic cetylpyridinium chloride micellar solutions: a rheological and scattering study.

    PubMed

    Gaudino, D; Pasquino, R; Stellbrink, J; Szekely, N; Krutyeva, M; Radulescu, A; Pyckhout-Hintzen, W; Grizzuti, N

    2016-12-21

    The micellar system based on cetylpyridinium chloride (CPyCl) and sodium salicylate (NaSal) in brine solution is investigated on both macro- and micro-length scales through rheology and scattering measurements. The linear viscoelasticity of the system and its structural parameters are explored by systematically changing the amount of NaSal over an extremely wide range of concentrations, thus producing salt-to-surfactant molar ratios from zero to about 8.5. As a result, the well-known non-monotonic behaviour of the zero-shear rate viscosity as a function of salinity can be connected to micellar morphological changes, whose driving force is represented by the simultaneous binding and screening actions of NaSal. The viscosity behaviour can be seen as a direct consequence of consecutive lengthening/shortening of the contour length, where the micelles attempt to minimize the electrostatic charge density on their surface. Along similar lines, the scattering measurements of the semidilute solutions show that the local stiffness of the micellar chain changes with increasing salt content influencing the elasticity of the resulting network. Within this general view, the branching of the micelles can be seen as a side effect attributable to the main character of the play, namely, the binding salt NaSal, whereas the overall dynamics of the system is driven by the considerable changes in the entanglement density of the micellar network.

  18. Microbial stability and quality of seasoned cracked green Aloreña table olives packed in diverse chloride salt mixtures.

    PubMed

    Bautista-Gallego, J; Arroyo-López, F N; Romero-Gil, V; Rodríguez-Gómez, F; García-García, P; Garrido-Fernández, A

    2013-11-01

    This work was conducted to determine the effect of the partial replacement of NaCl by KCl and CaCl2 (expressed as percentages, wt/vol) on the microbial stability and physicochemical characteristics of seasoned cracked olives using a simplex centroid mixture design. Neither Enterobacteriaceae nor lactic acid bacteria were found during the 50 days that olive packages were monitored. Therefore, microbial instability was considered due to the growth of yeasts, which were the only detected microorganisms; Saccharomyces cerevisiae and Pichia membranifaciens were the most relevant species. Yeasts decreased during the first 21 to 30 days after packing, but their populations rose to 3.5 log CFU/ml by the end of the storage period, clearly causing product deterioration. The partial substitution of NaCl with the other chloride salts slightly altered the phase of microbial inhibition and regrowth. Most of the quality characteristics were not affected by the use of the alternative salt mixtures, but the pH values and Cl(-) concentrations in brine decreased as the CaCl2 concentration increased. Hence, seasoned cracked table olives can be produced using a lower proportion of NaCl without causing significant changes in the shelf life and product quality, although further detailed studies are necessary to guarantee the stability of products packed with specific salt mixtures.

  19. Purification and characterization of halo-alkali-thermophilic protease from Halobacterium sp. strain HP25 isolated from raw salt, Lake Qarun, Fayoum, Egypt.

    PubMed

    Elbanna, Khaled; Ibrahim, Ibrahim M; Revol-Junelles, Anne-Marie

    2015-07-01

    A total of 33 halophilic protease producers were isolated from different salt samples collected from Emisal salt company at Lake Qarun, Fayoum, Egypt. Of these strains, an extremely halophilic strain that grew optimally at 30 % (w/v) NaCl was characterized and identified as Halobacterium sp. strain HP25 based on 16S rRNA gene sequencing and phenotypic characterization. A halo-alkali-thermophilic protease was purified in three successive steps from the culture supernatant. The purified halophilic protease consisted of a single polypeptide chain with a molecular mass of 21 kDa and was enriched 167-fold to a specific activity of 6350 U mg(-1). The purified enzyme was active over a broad pH range from 6.0 to 11.0, with maximum activity at pH 8.0, exhibited a broad temperature range from 30 to 80 °C with optimum activity at 60 °C, and was active at salt concentrations ranging from 5 to 25 % (w/v), with optimum activity at 17 % NaCl (w/v). The K M and V max values of the purified halophilic protease with casein as a substrate were 523 µg mL(-1) and 2500 µg min(-1) mL(-1), respectively. In addition, this enzyme was stable in the tested organic solvents and laundry detergents such methanol, propanol, butanol, hexane, Persil and Ariel. The unusual properties of this enzyme allow it to be used for various applications, such as the ripening of salted fish. Furthermore, its stability and activity in the presence of organic solvents and detergents also allow the use of this enzyme for further novel applications and as an additive in detergent formulations.

  20. Upregulation of apical sodium-chloride cotransporter and basolateral chloride channels is responsible for the maintenance of salt-sensitive hypertension.

    PubMed

    Capasso, Giovambattista; Rizzo, Maria; Garavaglia, Maria Lisa; Trepiccione, Francesco; Zacchia, Miriam; Mugione, Alessandra; Ferrari, Patrizia; Paulmichl, Markus; Lang, Florian; Loffing, Johannes; Carrel, Monique; Damiano, Sara; Wagner, Carsten A; Bianchi, Giuseppe; Meyer, Giuliano

    2008-08-01

    We investigated which of the NaCl transporters are involved in the maintenance of salt-sensitive hypertension. Milan hypertensive (MHS) rats were studied 3 mo after birth. In MHS, compared with normotensive strain (MNS), mRNA abundance, quantified by competitive PCR on isolated tubules, was unchanged, both for Na+/H+ isoform 3 (NHE3) and Na+-K+-2Cl- (NKCC2), but higher (119%, n = 5, P < 0.005) for Na+-Cl- (NCC) in distal convoluted tubules (DCT). These results were confirmed by Western blots, which revealed: 1) unchanged NHE3 in the cortex and NKCC2 in the outer medulla; 2) a significant increase (52%, n = 6, P < 0.001) of NCC in the cortex; 3) alpha- and beta-sodium channels [epithelial Na+ channel (ENaC)] unaffected in renal cortex and slightly reduced in the outer medulla, while gamma-ENaC remained unchanged. Pendrin protein expression was unaffected. The role of NCC was reinforced by immunocytochemical studies showing increased NCC on the apical membrane of DCT cells of MHS animals, and by clearance experiments demonstrating a larger sensitivity (P < 0.001) to bendroflumethiazide in MHS rats. Kidney-specific chloride channels (ClC-K) were studied by Western blot experiments on renal cortex and by patch-clamp studies on primary culture of DCT dissected from MNS and MHS animals. Electrophysiological characteristics of ClC-K channels were unchanged in MHS rats, but the number of active channels in a patch was 0.60 +/- 0.21 (n = 35) in MNS rats and 2.17 +/- 0.59 (n = 23) in MHS rats (P < 0.05). The data indicate that, in salt-sensitive hypertension, there is a strong upregulation, both of NCC and ClC-K along the DCT, which explains the persistence of hypertension.

  1. Preparation of Ferrotitanium Alloy from Ilmenite by Electrochemical Reduction in Chloride Molten Salts

    NASA Astrophysics Data System (ADS)

    Qi, Can-can; Hua, Yi-xin; Chen, Kong-hao; Jie, Ya-fei; Zhou, Zhong-ren; Ru, Juan-jian; Xiong, Li; Gong, Kai

    2016-02-01

    Ferrotitanium alloy is prepared by electrochemical reduction from ilmenite in LiCl-KCl and LiCl-KCl-CaCl2 molten salts, respectively. The products prepared are observed by x-ray diffraction (XRD). It is shown that Fe2Ti can be prepared from ilmenite in LiCl-KCl molten salt at 1073 K with a cell voltage of 3.2 V. Ilmenite can be electrochemically reduced to FeTi in LiCl-KCl-CaCl2 molten salt under the same condition. It is indicated that CaCl2 can promote the reaction and is favors the deoxidization of the FeTiO3.

  2. Uranium chloride extraction of transuranium elements from LWR fuel

    DOEpatents

    Miller, William E.; Ackerman, John P.; Battles, James E.; Johnson, Terry R.; Pierce, R. Dean

    1992-01-01

    A process of separating transuranium actinide values from uranium values present in spent nuclear oxide fuels containing rare earth and noble metal fission products as well as other fission products is disclosed. The oxide fuel is reduced with Ca metal in the presence of Ca chloride and a U-Fe alloy which is liquid at about 800.degree. C. to dissolve uranium metal and the noble metal fission product metals and transuranium actinide metals and rare earth fission product metals leaving Ca chloride having CaO and fission products of alkali metals and the alkali earth metals and iodine dissolved therein. The Ca chloride and CaO and the fission products contained therein are separated from the U-Fe alloy and the metal values dissolved therein. The U-Fe alloy having dissolved therein reduced metals from the spent nuclear fuel is contacted with a mixture of one or more alkali metal or alkaline earth metal halides selected from the class consisting of alkali metal or alkaline earth metal and Fe or U halide or a combination thereof to transfer transuranium actinide metals and rare earth metals to the halide salt leaving the uranium and some noble metal fission products in the U-Fe alloy and thereafter separating the halide salt and the transuranium metals dissolved therein from the U-Fe alloy and the metals dissolved therein.

  3. Uranium chloride extraction of transuranium elements from LWR fuel

    DOEpatents

    Miller, W.E.; Ackerman, J.P.; Battles, J.E.; Johnson, T.R.; Pierce, R.D.

    1992-08-25

    A process of separating transuranium actinide values from uranium values present in spent nuclear oxide fuels containing rare earth and noble metal fission products as well as other fission products is disclosed. The oxide fuel is reduced with Ca metal in the presence of Ca chloride and a U-Fe alloy which is liquid at about 800 C to dissolve uranium metal and the noble metal fission product metals and transuranium actinide metals and rare earth fission product metals leaving Ca chloride having CaO and fission products of alkali metals and the alkali earth metals and iodine dissolved therein. The Ca chloride and CaO and the fission products contained therein are separated from the U-Fe alloy and the metal values dissolved therein. The U-Fe alloy having dissolved therein reduced metals from the spent nuclear fuel is contacted with a mixture of one or more alkali metal or alkaline earth metal halides selected from the class consisting of alkali metal or alkaline earth metal and Fe or U halide or a combination thereof to transfer transuranium actinide metals and rare earth metals to the halide salt leaving the uranium and some noble metal fission products in the U-Fe alloy and thereafter separating the halide salt and the transuranium metals dissolved therein from the U-Fe alloy and the metals dissolved therein. 1 figure.

  4. Heating temperature dependence of Cr(III) oxidation in the presence of alkali and alkaline earth salts and subsequent Cr(VI) leaching behavior.

    PubMed

    Verbinnen, Bram; Billen, Pieter; Van Coninckxloo, Michiel; Vandecasteele, Carlo

    2013-06-04

    In this paper, the temperature dependence of Cr(III) oxidation in high temperature processes and the subsequent Cr(VI) leaching was studied using synthetic mixtures. It was experimentally shown that in the presence of alkali and alkaline earth salts, oxidation of Cr(III) takes place, consistent with thermodynamic calculations. Heating of synthetic mixtures of Cr2O3 and Na, K, or Ca salts led to elevated leaching of Cr(VI); in the presence of Na, more than 80% of the initial Cr(III) amount was converted to Cr(VI) at 600-800 °C. Kinetic experiments allowed explanation of the increase in Cr(VI) leaching for increasing temperatures up to 600-800 °C. After reaching a maximum in Cr(VI) leaching at temperatures around 600-800 °C, the leaching decreased again, which could be explained by the formation of a glassy phase that prevents leaching of the formed Cr(VI). By way of illustration, Cr(VI) formation and leaching was evaluated for a case study, the fabrication of ceramic material from contaminated sludge. Based on the proposed reaction mechanisms, countermeasures to prevent Cr oxidation (addition of NH4H2PO4, heating under inert atmosphere) were proposed and successfully tested for synthetic mixtures and for the case study.

  5. Chemical equilibrium model for interfacial activity of crude oil in aqueous alkaline solution: the effects of pH, alkali and salt

    SciTech Connect

    Chan, M.; Yen, T.F.

    1980-11-01

    A chemical equilibrium model for interfacial activity of crude in aqueous alkaline solution is proposed. The model predicts the observed effects of pH and concentrations of alkali and salt on the interfacial tension (IFT). The model proposed was shown to describe the observed effects of acid content, pH, and sodium ions on the interfacial activity of crude oil in water. Once the pH of the interface reaches the pKa of the acids, sometimes with the help of addition of some salt, the IFT experiences a sudden steep drop to the range of 10/sup -2/ dynes/cm. After that, further addition of sodium either in the form of NaOH or NaCl is going to increase the IFT due to a shift of equilibriumn to the formation of undissociated soap. This was confirmed by the difference in the observed effect of sodium on the IFT of the extracted soap molecules which are dissociated easily and those which are associated highly and precipitated easily. These soap molecules have dissociation constant values ranging from below 10/sup -2/ to above one. 13 references.

  6. Hot Corrosion Behavior of Arc-Sprayed Highly Dense NiCr-Based Coatings in Chloride Salt Deposit

    NASA Astrophysics Data System (ADS)

    Qin, Enwei; Yin, Song; Ji, Hua; Huang, Qian; Liu, Zekun; Wu, Shuhui

    2017-03-01

    To make cities more environmentally friendly, combustible wastes tend to be incinerated in waste-to-energy power plant boilers. However, release of chlorine gas (Cl2) during incineration causes serious problems related to hot corrosion of boiler tubes and poses a safety threat for such plants. In this study, a pseudo-de Laval nozzle was employed in a twin-wire arc spray system to enhance the velocity of in-flight particles. Highly dense NiCr-based coatings were obtained using the modified nozzle gun. The coating morphology was characterized by optical microscopy and scanning electron microscopy, and hot corrosion testing was carried out in a synthetic molten chloride salt environment. Results showed that the dense NiCr-based coatings exhibited high resistance against corrosion by chlorine, which can be related to the typical splat lamellar microstructure and chemical composition as well as minor alloying elements such as Ti and Mo.

  7. Basic trends and chief products in the electrolysis of methanolic solutions of monomethyl adipate and its alkali salts

    SciTech Connect

    Shul'zhenko, G.I.; Freidlin, G.N.; Kovsman, E.P.; Vasil'ev, Yu. B.

    1986-08-01

    Preparative electrolysis under galvanostatic conditions was used to study the effect of the principal adjustable process parameters, such as temperature, the water content of the original electrolyte, current density, electrolysis time, and the concentration of monoester salt, on the formation of methyl valerate and methyl allylacetate. The character of the influence of these parameters was established.

  8. Inefficacy of osmotic backwash induced by sodium chloride salt solution in controlling SWRO membrane fouling

    NASA Astrophysics Data System (ADS)

    Farooque, A. Mohammed; Al-Jeshi, Subhi; Saeed, Mohamed O.; Alreweli, Ali

    2014-12-01

    A study was conducted to evaluate the efficacy of osmotic backwash induced by high salt (NaCl) concentration solution on feed side of seawater reverse osmosis (SWRO) membranes, online and offline, in controlling membrane fouling and therefore minimizing/eliminating the need for chemical cleaning. SWRO membranes were deliberately fouled by feeding seawater from an open intake located on the Arabian Gulf Coast without dosing chemicals. The fouled membranes were subjected to offline cleaning with the salt solution of up to 25 % concentration. Despite the partial removal of foulants from the membrane surface, SWRO membrane performance could not be restored, indicating the ineffectiveness of osmotic backwash in aiding offline salt cleaning. Similarly, online osmotic backwash was found to be not only ineffective in removing foulants from membrane surfaces but actually increased the fouling rate, as indicated by faster fouling rates compared to other cases. Although the driving force required for the osmotic backwash existed, the generated back flow proved to be insufficient to detach foulants from membrane surfaces. During the study period, the average SWRO membrane flux was maintained between 19 and 23 LMH, whereas the average generated back flow flux by high salt concentration solution was only 11 LMH, which was not adequate to remove foulants from membrane surfaces. Moreover, it seems that the membrane configuration as well as inherent microstructure of SWRO membrane places certain constraints on the osmotic backwash process and renders osmotic backwash ineffective in tackling SWRO membrane fouling. Hence, chemical cleaning is essential to restore SWRO membrane performance whenever fouling occurs, and the use of highly concentrated salt solution does not have any significant benefit. Membrane autopsy revealed only an insignificant accumulation of biofouling layer despite the absence of disinfection. However, it was shown that culturable biofilm bacteria species

  9. Molecular dynamics simulations of the structure of the graphene-ionic liquid/alkali salt mixtures interface.

    PubMed

    Méndez-Morales, Trinidad; Carrete, Jesús; Pérez-Rodríguez, Martín; Cabeza, Óscar; Gallego, Luis J; Lynden-Bell, Ruth M; Varela, Luis M

    2014-07-14

    We performed molecular dynamics simulations of mixtures of 1-butyl-3-methylimidazolium tetrafluoroborate with lithium tetrafluoroborate and potassium tetrafluoroborate between two charged and uncharged graphene walls, in order to analyze the structure of the well-known formation of layers that takes place on liquids under confinement. For this purpose, we studied the molecular density profiles, free energy profiles for bringing lithium and potassium cations from the bulk mixture to the graphene wall and the orientational distributions of imidazolium rings within the first adsorbed layer as a function of salt concentration and electrode potential. The charge densities in the electrodes were chosen to be zero and ±1 e nm(-2), and the salt molar percentages were %salt = 0, 10 and 25. We found that the layered structure extends up to 1-2 nm, where the bulk behaviour is recovered. In addition, whereas for the neutral surface the layers are composed of both ionic species, increasing the electrode potential, the structure changes to alternating cationic and anionic layers leading to an overcompensation of the charge of the previous layer. We also calculated the distribution of angles of imidazolium rings near neutral and charged graphene walls, finding a limited influence of the added salt. In addition, the average tilt of the imidazolium ring within the first layer goes from 36° with respect to a normal vector to the uncharged graphene wall to 62° in the presence of charged walls. The free energy profiles revealed that lithium and potassium ions are adsorbed on the negative surface only for the highest amount of salt, since the free energy barriers for approaching this electrode are considerably higher than kBT.

  10. Role of sequence in salt-bridge formation for alkali metal cationized GlyArg and ArgGly investigated with IRMPD spectroscopy and theory.

    PubMed

    Prell, James S; Demireva, Maria; Oomens, Jos; Williams, Evan R

    2009-01-28

    The roles of hydrogen bonding, electrostatic interactions, sequence, gas-phase basicity, and molecular geometry in determining the structures of protonated and alkali metal-cationized glycyl-L-arginine (GlyArg) and L-arginylglycine (ArgGly) were investigated using infrared multiple photon dissociation spectroscopy in the spectral range 900-1800 cm(-1) and theory. The IRMPD spectra clearly indicate that GlyArg x M(+), M = Li, Na, and Cs, form similar salt-bridge (SB) structures that do not depend significantly on metal ion size. In striking contrast, ArgGly x Li(+) exists in a charge-solvated (CS) form, whereas ArgGly x M(+), M = K and Cs, form SB structures. SB and CS structures are similarly populated for ArgGly x Na(+). Computed energies of low-energy structures are consistent with these results deduced from the experimental spectra. By comparison to Arg x M(+), GlyArg x M(+) and ArgGly x M(+) have a greater and lesser propensity, respectively, to form SB structures. The greater propensity for GlyArg to adopt SB structures in complexes with smaller metal cations than for ArgGly is due to the ability of alkali metal-cationized GlyArg to adopt a nearly linear arrangement of formal charge sites, a structure unfavorable for ArgGly complexes due to geometric constraints induced by its different amino acid sequence. The amide carbonyl oxygen solvates charge in both the SB and CS form of both dipeptides. ArgGly is calculated to be slightly more basic than GlyArg, indicating that differences in intrinsic basicity do not play a role in the relative SB stabilization of these ions. Loss of a neutral water molecule from complexes in which SB structures are most stable indicates that CS structures are intermediates in the dissociation pathway, but these intermediates do not contribute to the measured IRMPD spectra.

  11. Sodium Chloride Diffusion during Muscle Salting Evidenced by Energy-Dispersive X-ray Spectroscopy Imaging.

    PubMed

    Filgueras, Rénata; Peyrin, Frédéric; Vénien, Annie; Hénot, Jean Marc; Astruc, Thierry

    2016-01-27

    To better understand the relationship between the muscle structure and NaCl transfers in meat, we used energy-dispersive X-ray spectroscopy (EDS) coupled with scanning electron microscopy (SEM) to analyze brined and dry-salted rat muscles. The muscles were freeze-dried to avoid the delocalization of soluble ions that happens in regular dehydration through a graded series of ethanol. Na and Cl maps were superimposed on SEM images to combine the muscle structure and NaCl diffusion. Brining causes rapid diffusion of NaCl through the tissue. Most brine diffuses in a linear front from the muscle surface, but a small proportion enters through the perimysium network. The muscle area penetrated by brine shows heterogeneous patterns of NaCl retention, with some connective tissue islets containing more NaCl than other parts of perimysium. NaCl penetration is considerably slower after dry salting than after brining.

  12. Hypertension, dietary salt intake, and the role of the thiazide-sensitive sodium chloride transporter NCCT.

    PubMed

    Glover, Mark; Zuber, Annie Mercier; O'Shaughnessy, Kevin M

    2011-02-01

    A high salt intake in industrialized countries is an important cardiovascular risk factor. It remains at typically twice the maximum recommended levels of 5-6 g/day, and halving this would have enormous public health benefit in preventing stroke and cardiovascular disease. Salt homeostasis can also be affected pharmacologically by diuretic drugs that target mechanisms within the distal kidney nephron to cause salt wasting. Indeed, thiazide-type diuretics are among the most widely used agents in the management of hypertension and work by blocking NCCT, the NaCl-transporter in the distal nephron. The biology of this membrane transporter was not previously well understood until the discovery of the molecular basis of a rare familial form of hypertension called Gordon syndrome (pseudohypoaldosteronism type 2, PHAII). This has established that the NCCT transporter is dynamically regulated in the kidney by WNK kinases and a signaling cascade using a second kinase called SPAK. Common polymorphisms in the SPAK gene have recently been shown to affect blood pressure in human cohorts and removing its function lowers blood pressure in mice. The SPAK-deficient mouse actually has a phenotype reminiscent of Gitelman syndrome. This suggests that specific inhibitors of SPAK kinase may provide a novel class of diuretic drugs to lower blood pressure through salt wasting. The expectation is that SPAK inhibitors would mimic the on-target effects of thiazides but not their adverse off-target effects. An antihypertensive drug that could lower blood pressure with the efficacy of a thiazide without producing metabolic side effects such as hyperuricaemia or impaired glucose tolerance is therapeutically very attractive. It also exemplifies how data coming from the rare monogenic hypertension syndromes can together with genome-wide association studies in hypertension deliver novel druggable targets.

  13. Effects of pH, sodium chloride, and curing salt on the infectivity of Toxoplasma gondii tissue cysts.

    PubMed

    Pott, S; Koethe, M; Bangoura, B; Zöller, B; Daugschies, A; Straubinger, R K; Fehlhaber, K; Ludewig, M

    2013-06-01

    Toxoplasma gondii is one of the most common zoonotic parasites in the world. The parasite causes no or mild symptoms in immunocompetent humans. However, a high potential hazard exists for seronegative pregnant women and immunocompromised patients. The consumption of meat containing tissue cysts or oocyst-contaminated vegetables and fruits or the handling of cat feces poses a high risk of infection with T. gondii. It is known that raw minced meat, raw fresh sausages, and locally produced raw meat products are possible causes of T. gondii infection. The infectivity of T. gondii tissue cysts in meat products depends, among other factors, on the pH and the salt concentration. Therefore, the impact of these two factors on the tissue cysts was examined. For this purpose, dissected musculature and brain from experimentally infected mice (donor mice) were placed in a cell culture medium (RPMI 1640). The medium was adjusted to different pH values (pH 5, 6, and 7) with lactic acid and to different salt concentrations (2.0, 2.5, and 3.0%) with sodium chloride (NaCl) or nitrite-enriched curing salt (NCS) for the various tests. After storage at 4°C for different time periods, the materials were fed to bioassay mice. Later, the brains were examined for presence of T. gondii to assess the infectivity. The data show that T. gondii tissue cysts have a high pH tolerance. Cysts were infectious in the muscle for up to 26 days (pH 5). In contrast to their tolerance to pH, cysts were very sensitive to salt. Muscle cysts survived at an NaCl concentration of up to 2.0% only, and for no longer than 8 days. At NaCl concentrations of 2.5 and 3.0%, the cysts lost their infectivity after 1 day. When NCS instead of NaCl was used under the same conditions, T. gondii muscle cysts retained infectivity for only 4 days at 2.0%. Consequently, NCS (NaCl plus 0.5% nitrite) has a stronger effect on T. gondii cysts than does common table salt. Sausages produced with low NaCl concentration and short

  14. Interfacial behavior of perchlorate versus chloride ions in saturated aqueous salt solutions

    SciTech Connect

    Ghosal, S; Kuo, I W; Baer, M D; Bluhm, H

    2009-04-14

    In recent years combination of theoretical and experimental work have presented a novel view of the aqueous interface wherein hard and/or multiply charged ions are excluded from the interface, but large polarizable anions show interfacial enhancement relative to the bulk. The observed trend in the propensity of anions to adsorb at the air/water interface appears to be reverse of the Hofmeister series for anions. This study focuses on experimental and theoretical examination of the partitioning behavior of perchlorate (ClO{sub 4}{sup -}) and chloride (Cl{sup -}) ions at the air/water interface. We have used ambient pressure X-ray photoelectron spectroscopy technique to directly probe the interfacial concentrations of ClO{sub 4}{sup -} and Cl{sup -} ions in sodium perchlorate and sodium chloride solutions, respectively. Experimental observations are compared with first principles molecular dynamics simulations. Both experimental and simulation results show enhancement of ClO{sub 4}{sup -} ion at the interface, compared with the absence of such enhancement in the case of Cl{sup -} ion. These observations are in agreement with the expected trend in the interfacial propensity of anions based on the Hofmeister series.

  15. The effects of particle-size distribution and chloride depletion of sea-salt aerosols on estimating atmospheric deposition at a coastal site

    NASA Astrophysics Data System (ADS)

    Harkel, M. J. Ten

    Estimating atmospheric deposition in a coastal region cannot be done without taking care of the size distribution and amount of chloride depletion of sea-salt aerosols. Size distribution of the dry deposition particles is important when the approach of Ulrich (1983, Effects of Accumulation of Air Pollutants in Forest Ecosystems, pp. 33-45. Reidel, Dordrecht) is used to estimate total atmospheric deposition levels in a coastal area. A sodium deposition model demonstrated that the presumption of an equal size of sodium aerosols and chloride, potassium, magnesium and calcium aerosols is not valid in the coastal zone. Modelled aerosol diameter distribution showed that more than 50% of the aerosols deposited in this zone is larger than 20 μm. Besides an anthropogenic source, the reaction of nitric or sulphuric acid with sea-salt aerosols, by which HCl (g) is formed, can be a second source of an excess of chloride in throughflow compared to sodium. The newly formed HCl can deposit as dry deposition on a vegetation, and not as dry bulk deposition. Chloride loss in the bulk deposition at the coastal sites was up to 35% in summertime. Chloride depletion also affects the calculation of potential acid deposition (PAD) in the coastal zone. Part of the NO 3- and excess SO 42- deposition should not be taken into account when calculating the PAD, because it is neutralized by the sea-salt. This effect decreases very soon with increasing distance to the sea. Implementing chloride depletion in calculating yearly PAD at 500 m from the coastline decreased the PAD with 26%. At 2000 m this decrease was 14%. However, in some cases PAD values on a fortnightly base were observed to decrease more than 50% after implementing chloride depletion.

  16. Radiolysis of Salts and Long-Term Storage Issues for Both Pure and Impure PuO{sub 2} Materials in Plutonium Storage Containers

    SciTech Connect

    Lav Tandon

    2000-05-01

    The Material Identification and Surveillance (MIS) project sponsored a literature search on the effects of radiation on salts, with focus on alkali chlorides. The goal of the survey was to provide a basis for estimating the magnitude of {alpha} radiation effects on alkali chlorides that can accompany plutonium oxide (PuO{sub 2}) into storage. Chloride radiolysis can yield potentially corrosive gases in plutonium storage containers that can adversely affect long-term stability. This literature search was primarily done to provide a tutorial on this topic, especially for personnel with nonradiation chemistry backgrounds.

  17. CO2 gasification reactivity of biomass char: catalytic influence of alkali, alkaline earth and transition metal salts.

    PubMed

    Lahijani, Pooya; Zainal, Zainal Alimuddin; Mohamed, Abdul Rahman; Mohammadi, Maedeh

    2013-09-01

    This study investigates the influence of alkali (Na, K), alkaline earth (Ca, Mg) and transition (Fe) metal nitrates on CO2 gasification reactivity of pistachio nut shell (PNS) char. The preliminary gasification experiments were performed in thermogravimetric analyzer (TGA) and the results showed considerable improvement in carbon conversion; Na-char>Ca-char>Fe-char>K-char>Mg-char>raw char. Based on TGA studies, NaNO3 (with loadings of 3-7 wt%) was selected as the superior catalyst for further gasification studies in bench-scale reactor; the highest reactivity was devoted to 5 wt% Na loaded char. The data acquired for gasification rate of catalyzed char were fitted with several kinetic models, among which, random pore model was adopted as the best model. Based on obtained gasification rate constant and using the Arrhenius plot, activation energy of 5 wt% Na loaded char was calculated as 151.46 kJ/mol which was 53 kJ/mol lower than that of un-catalyzed char.

  18. Comparison of cation exchange resins for recovering americium and plutonium from chloride salts

    SciTech Connect

    Silva, R.A.; Navratil, J.D.

    1983-01-01

    Macroreticular and microreticular cation exchange resins were compared for their capability of recovering americium and plutonium from solutions of calcium, magnesium, potassium, and sodium chlorides. Americium and plutonium breakthrough capacity and elution behavior of the resins were determined. Of the resins tested, Dowex MSC-1 was selected as the most efficient because of its favorable capacity and excellent elution behavior. Actinide eluting agents were also studied. More concentrated (9.0M) nitric acid was found to elute plutonium faster than 7.0M HNO/sub 3/ used previously while 7.0M HNO/sub 3/-0.1M NaNO/sub 2/ eluted americium fastest. 4 tables.

  19. Methyl-methionine as a precursor for methyl chloride and dimethyl sulphide produced in terrestrial salt lakes

    NASA Astrophysics Data System (ADS)

    Mulder, I.; Krause, T.; Studenroth, S.; Tubbesing, C.; Kotte, K.; Schöler, H. F.

    2012-04-01

    Volatile organic halocarbons (VOX) play an important role in the photochemical processes of the lower atmosphere and information on the geogenic origin of these compounds will help to understand global VOX budgets and fluxes. However, investigations concerned with occurrence of VOX in fluid inclusions of rocks and minerals are scarce (Harnisch and Eisenhauer, 1998; Svensen et al., 2009). The composition of volatile organic carbons (VOC) trapped in fluid inclusions of halite crystals deposited in recent salt pans was analysed using a purge and trap GC-MS technique. Besides an array of identified volatile compounds we noticed the occurrence of chloromethane (MeCl), dimethylsulfide (DMS) or both in most of a divers set of samples. Methyl chloride with an atmospheric burden of 4 to 5 Tg, is the most abundant halocarbon in the atmosphere. It plays a significant role in chlorine-catalyzed ozone destruction in the stratosphere (Keppler et al., 2005; Montzka and Frazer, 2003). DMS is the major natural, mainly marine, source of sulphur in the atmosphere and contributes to both the tropospheric burden of sulphur as well as cloud properties via oxidation to acidic aerosols (Kloster et al., 2006; Sievert et al., 2007). It is also known that a conversion of methionine (MET) to dimethylsulfonium-propionate by phytoplankton takes place, which in turn serves as the main precursor for DMS emission from the surface ocean to the atmosphere (Sievert et al., 2007). In search of a possible precursor for the above mentioned two compounds we hypothesize that the compounds trapped in the fluid inclusions represent compounds originally formed in the immediately subjacent sediment. MET, as one of three sulfur containing amino acids, could potentially serve as a precursor for MeCl and DMS formed in salt lake environments. To test these hypotheses, we measured selected sediment samples that correspond to the previously measured salt samples. Separately, we studied the temperature dependence of

  20. Magnetic susceptibility of alkali-tetracyanoquinodimethane salts and extended Hubbard models with bond order and charge density wave phases.

    PubMed

    Kumar, Manoranjan; Topham, Benjamin J; Yu, RuiHui; Ha, Quoc Binh Dang; Soos, Zoltán G

    2011-06-21

    The molar spin susceptibilities χ(T) of Na-tetracyanoquinodimethane (TCNQ), K-TCNQ, and Rb-TCNQ(II) are fit quantitatively to 450 K in terms of half-filled bands of three one-dimensional Hubbard models with extended interactions using exact results for finite systems. All three models have bond order wave (BOW) and charge density wave (CDW) phases with boundary V = V(c)(U) for nearest-neighbor interaction V and on-site repulsion U. At high T, all three salts have regular stacks of TCNQ(-) anion radicals. The χ(T) fits place Na and K in the CDW phase and Rb(II) in the BOW phase with V ≈ V(c). The Na and K salts have dimerized stacks at T < T(d) while Rb(II) has regular stacks at 100 K. The χ(T) analysis extends to dimerized stacks and to dimerization fluctuations in Rb(II). The three models yield consistent values of U, V, and transfer integrals t for closely related TCNQ(-) stacks. Model parameters based on χ(T) are smaller than those from optical data that in turn are considerably reduced by electronic polarization from quantum chemical calculation of U, V, and t of adjacent TCNQ(-) ions. The χ(T) analysis shows that fully relaxed states have reduced model parameters compared to optical or vibration spectra of dimerized or regular TCNQ(-) stacks.

  1. [Characteristics of 'salt island' and 'fertile island' for Tamarix chinensis and soil carbon, nitrogen and phosphorus ecological stoichiometry in saline-alkali land].

    PubMed

    Zhang, Li-hua; Chen, Xiao-bing

    2015-03-01

    To clarify the nutrient characteristics of 'salt island' and 'fertile island' effects in saline-alkali soil, the native Tamarix chinensis of the Yellow River Delta (YRD) was selected to measure its soil pH, electrical conductivity (EC), organic carbon (SOC), total nitrogen (N), total phosphorus (P) and their stoichiometry characteristics at different soil depths. The results showed that soil pH and EC increased with the increasing soil depth. Soil EC and P in the 0-20 cm layer decreased and increased from canopied area to interspace, respectively. SOC, N, N/P and C/P in the 20-40 cm soil layer decreased, and C/N increased from the shrub center to interspace. SOC and N contents between island and interspace both decreased but P content decreased firstly and then increased with the increasing soil depth. Soil pH correlated positively with EC. In addition, pH and EC correlated negatively with C, N, P contents and their ecological stoichiometry.

  2. The Influence of Calcium Chloride Deicing Salt on Phase Changes and Damage Development in Cementitious Materials

    PubMed Central

    Farnam, Yaghoob; Dick, Sarah; Wiese, Andrew; Davis, Jeffrey; Bentz, Dale; Weiss, Jason

    2015-01-01

    The conventional CaCl2-H2O phase diagram is often used to describe how calcium chloride behaves when it is used on a concrete pavement undergoing freeze-thaw damage. However, the chemistry of the concrete can alter the appropriateness of using the CaCl2-H2O phase diagram. This study shows that the Ca(OH)2 present in a hydrated portland cement can interact with CaCl2 solution creating a behavior that is similar to that observed in isoplethal sections of a ternary phase diagram for a Ca(OH)2-CaCl2-H2O system. As such, it is suggested that such isoplethal sections provide a reasonable model that can be used to describe the behavior of concrete exposed to CaCl2 solution as the temperature changes. Specifically, the Ca(OH)2 can react with CaCl2 and H2O resulting in the formation of calcium oxychloride. The formation of the calcium oxychloride is expansive and can produce damage in concrete at temperatures above freezing. Its formation can also cause a significant decrease in fluid ingress into concrete. For solutions with CaCl2 concentrations greater than about 11.3 % (by mass), it is found that calcium oxychloride forms rapidly and is stable at room temperature (23 °C). PMID:26692655

  3. The Influence of Calcium Chloride Deicing Salt on Phase Changes and Damage Development in Cementitious Materials.

    PubMed

    Farnam, Yaghoob; Dick, Sarah; Wiese, Andrew; Davis, Jeffrey; Bentz, Dale; Weiss, Jason

    2015-11-01

    The conventional CaCl2-H2O phase diagram is often used to describe how calcium chloride behaves when it is used on a concrete pavement undergoing freeze-thaw damage. However, the chemistry of the concrete can alter the appropriateness of using the CaCl2-H2O phase diagram. This study shows that the Ca(OH)2 present in a hydrated portland cement can interact with CaCl2 solution creating a behavior that is similar to that observed in isoplethal sections of a ternary phase diagram for a Ca(OH)2-CaCl2-H2O system. As such, it is suggested that such isoplethal sections provide a reasonable model that can be used to describe the behavior of concrete exposed to CaCl2 solution as the temperature changes. Specifically, the Ca(OH)2 can react with CaCl2 and H2O resulting in the formation of calcium oxychloride. The formation of the calcium oxychloride is expansive and can produce damage in concrete at temperatures above freezing. Its formation can also cause a significant decrease in fluid ingress into concrete. For solutions with CaCl2 concentrations greater than about 11.3 % (by mass), it is found that calcium oxychloride forms rapidly and is stable at room temperature (23 °C).

  4. Development of a niobium-doped titania inert anode for titanium electrowinning in molten chloride salts.

    PubMed

    Snook, Graeme A; McGregor, Katherine; Urban, Andrew J; Lanyon, Marshall R; Donelson, R; Pownceby, Mark I

    2016-08-15

    The direct electrochemical reduction of solid titanium dioxide in a chloride melt is an attractive method for the production of titanium metal. It has been estimated that this type of electrolytic approach may reduce the costs of producing titanium sponge by more than half, with the additional benefit of a smaller environmental footprint. The process utilises a consumable carbon anode which releases a mixture of CO2 and CO gas during electrolysis, but suffers from low current efficiency due to the occurrence of parasitic side reactions involving carbon. The replacement of the carbon anode with a cheap, robust inert anode offers numerous benefits that include: elimination of carbon dioxide emissions, more efficient cell operation, opportunity for three-dimensional electrode configurations and reduced electrode costs. This paper reports a study of Nb-doped titania anode materials for inert anodes in a titanium electrolytic reduction cell. The study examines the effect of niobium content and sintering conditions on the performance of Nb-doped TiO2 anodes in laboratory-scale electrolysis tests. Experimental findings, including performance in a 100 h laboratory electrolysis test, are described.

  5. Corrosion of alloys in a chloride molten salt (NaCl-LiCl) for solar thermal technologies

    SciTech Connect

    Gomez-Vidal, Judith C.; Tirawat, Robert

    2016-12-01

    Next-generation solar power conversion systems in concentrating solar power (CSP) applications require high-temperature advanced fluids in the range of 600-800 degrees C. Current commercial CSP plants use molten nitrate salt mixtures as the heat transfer fluid and the thermal energy storage (TES) media while operating with multiple hours of energy capacity and at temperatures lower than 565 degrees C. At higher temperatures, the nitrates cannot be used because they decompose. Molten chloride salts are candidates for CSP applications because of their high decomposition temperatures and good thermal properties; but they can be corrosive to common alloys used in vessels, heat exchangers, and piping at these elevated temperatures. In this article, we present the results of the corrosion evaluations of several alloys in eutectic 34.42 wt% NaCl - 65.58 wt% LiCl at 650-700 degrees C in nitrogen atmosphere. Electrochemical evaluations were performed using open-circuit potential followed by a potentiodynamic polarization sweep. Corrosion rates were determined using Tafel slopes and Faraday's law. A temperature increase of as little as 50 degrees C more than doubled the corrosion rate of AISI stainless steel 310 and Incoloy 800H compared to the initial 650 degrees C test. These alloys exhibited localized corrosion. Inconel 625 was the most corrosion-resistant alloy with a corrosion rate of 2.80+/-0.38 mm/year. For TES applications, corrosion rates with magnitudes of a few millimeters per year are not acceptable because of economic considerations. Additionally, localized corrosion (intergranular or pitting) can be catastrophic. Thus, corrosion-mitigation approaches are required for advanced CSP plants to be commercially viable.

  6. Rubidium chloride tolerant callus cultures of rice (Oryza sativa L.) accumulate more potassium and cross tolerate to other salts.

    PubMed

    Naga Amrutha, R; Jogeswar, G; Srilaxmi, P; Kavi Kishor, P B

    2007-09-01

    Callus cultures from salt tolerant (CSR-10) and susceptible (Swarnadhan) varieties of Oryza sativa L. were established in Murashige and Skoog's (MS) medium containing lethal concentrations (50 mM) of rubidium chloride (RbCl) as a selective agent. While 95-100% cells were viable in callus cultures grown without RbCl, viability was 75% in 50 mM RbCl selected cultures. Growth of RbCl selected calli in presence of salt was comparable to that of callus grown without it. Cells tolerant to RbCl showed more vacuoles and accumulated more K(+) in comparison with their corresponding controls. Suspension cultures were established and uptake of (86)Rb(+) was measured at 10 and 20 min intervals, which revealed a linear relationship between the absorption of K(+) and time. Callus cultures (560-day-old) tolerant to 50 mM RbCl regenerated shoots with 35-40% frequencies in both the varieties, but the same age-old callus grown in the medium devoid of RbCl did not show any organogenesis. Callus cultures that are tolerant to 50 mM RbCl when exposed to 25 mM LiCl, 50 mM NaCl, 50 mM KCl and 25 mM CsCl also exhibited cross tolerance in both the varieties. This is the first time that a callus line of rice resistant to RbCl was raised and shown to accumulate a major cation K(+ )and also an increased influx of it.

  7. Mapping of road-salt-contaminated groundwater discharge and estimation of chloride load to a small stream in southern New Hampshire, USA

    USGS Publications Warehouse

    Harte, P.T.; Trowbridge, P.R.

    2010-01-01

    Concentrations of chloride in excess of State of New Hampshire water-quality standards (230 mg/l) have been measured in watersheds adjacent to an interstate highway (I-93) in southern New Hampshire. A proposed widening plan for I-93 has raised concerns over further increases in chloride. As part of this effort, road-salt-contaminated groundwater discharge was mapped with terrain electrical conductivity (EC) electromagnetic (EM) methods in the fall of 2006 to identify potential sources of chloride during base-flow conditions to a small stream, Policy Brook. Three different EM meters were used to measure different depths below the streambed (ranging from 0 to 3 m). Results from the three meters showed similar patterns and identified several reaches where high EC groundwater may have been discharging. Based on the delineation of high (up to 350 mmhos/m) apparent terrain EC, seven-streambed piezometers were installed to sample shallow groundwater. Locations with high specific conductance in shallow groundwater (up to 2630 mmhos/m) generally matched locations with high streambed (shallow subsurface) terrain EC. A regression equation was used to convert the terrain EC of the streambed to an equivalent chloride concentration in shallow groundwater unique for this site. Utilizing the regression equation and estimates of onedimensional Darcian flow through the streambed, a maximum potential groundwater chloride load was estimated at 188 Mg of chloride per year. Changes in chloride concentration in stream water during streamflow recessions showed a linear response that indicates the dominant process affecting chloride is advective flow of chloride-enriched groundwater discharge. Published in 2010 by John Wiley & Sons, Ltd.

  8. Solid-State (17)O NMR of Oxygen-Nitrogen Singly Bonded Compounds: Hydroxylammonium Chloride and Sodium Trioxodinitrate (Angeli's Salt).

    PubMed

    Lu, Jiasheng; Kong, Xianqi; Terskikh, Victor; Wu, Gang

    2015-07-23

    We report a solid-state NMR study of (17)O-labeled hydroxylammonium chloride ([H(17)O-NH3]Cl) and sodium trioxodinitrate monohydrate (Na2[(17)ONNO2]·H2O, Angeli's salt). The common feature in these two compounds is that they both contain oxygen atoms that are singly bonded to nitrogen. For this class of oxygen-containing functional groups, there is very limited solid-state (17)O NMR data in the literature. In this work, we experimentally measured the (17)O chemical shift and quadrupolar coupling tensors. With the aid of plane-wave DFT computation, the (17)O NMR tensor orientations were determined in the molecular frame of reference. We found that the characteristic feature of an O-N single bond is that the (17)O nucleus exhibits a large quadrupolar coupling constant (13-15 MHz) but a rather small chemical shift anisotropy (100-250 ppm), in sharp contrast with the nitroso (O═N) functional group for which both quantities are very large (e.g., 16 MHz and 3000 ppm, respectively).

  9. Effects of temperature, concentration, and uranium chloride mixture on zirconium electrochemical studies in LiClsbnd KCl eutectic salt

    NASA Astrophysics Data System (ADS)

    Hoover, Robert O.; Yoon, Dalsung; Phongikaroon, Supathorn

    2016-08-01

    Experimental studies were performed to provide measurement and analysis of zirconium (Zr) electrochemistry in LiClsbnd KCl eutectic salt at different temperatures and concentrations using cyclic voltammetry (CV). An additional experimental set with uranium chloride added into the system forming UCl3sbnd ZrCl4sbnd LiClsbnd KCl was performed to explore the general behavior of these two species together. Results of CV experiments with ZrCl4 show complicated cathodic and anodic peaks, which were identified along with the Zr reactions. The CV results reveal that diffusion coefficients (D) of ZrCl4 and ZrCl2 as the function of temperature can be expressed as DZr(IV) = 0.00046exp(-3716/T) and DZr(II) = 0.027exp(-5617/T), respectively. The standard rate constants and apparent standard potentials of ZrCl4 at different temperatures were calculated. Furthermore, the results from the mixture of UCl3 and ZrCl4 indicate that high concentrations of UCl3 hide the features of the smaller concentration of ZrCl4 while Zr peaks become prominent as the concentration of ZrCl4 increases.

  10. Synthesis of high-molecular-weight polymer of methyl chloride salt of N,N-dimethylaminoethyl methacrylate by radiation-induced polymerization at high pressure. [Gamma radiation

    SciTech Connect

    Ishigaki, I.; Okada, T.; Sasuga, T.; Takehisa, M.; Machi, S.

    1981-02-01

    Polymer of the methyl chloride salt of N,N-dimethylaminoethyl methacrylate and its copolymer with acrylamide are used as cationic flocculants for the treatment of waste water containing organic suspensions. As reported, radiation-induced polymerization is one of the most convenient methods because of its temperature independence of initiation and extremely large G-value. In general, a flocculant with higher molecular weight has larger flocculation effects. The high-molecular-weight products were prepared in high monomer concentration and a low dose rate. This paper concerns the polymerization and copolymerization of methyl chloride salt of N,N-dimethylaminoethyl methacrylate at high pressure, up to 7000 kg/cm/sup 2/, providing high-molecular-weight cationic flocculants.

  11. [Sources of error in the European Pharmacopoeia assay of halide salts of organic bases by titration with alkali].

    PubMed

    Kószeginé, S H; Ráfliné, R Z; Paál, T; Török, I

    2000-01-01

    A short overview has been given by the authors on the titrimetric assay methods of halide salts of organic bases in the pharmacopoeias of greatest importance. The alternative procedures introduced by the European Pharmacopoeia Commission some years ago to replace the non-aqueous titration with perchloric acid in the presence of mercuric acetate have also been presented and evaluated. The authors investigated the limits of applicability and the sources of systematic errors (bias) of the strongly preferred titration with sodium hydroxide in an alcoholic medium. To assess the bias due to the differences between the results calculated from the two inflexion points of the titration curves and the two real endpoints corresponding to the strong and weak acids, respectively, the mathematical analysis of the titration curve function was carried out. This bias, generally negligible when the pH change near the endpoint of the titration is more than 1 unit, is the function of the concentration, the apparent pK of the analyte and the ionic product of water (ethanol) in the alcohol-water mixtures. Using the validation data gained for the method with the titration of ephedrine hydrochloride the authors analysed the impact of carbon dioxide in the titration medium on the additive and proportional systematic errors of the method. The newly introduced standardisation procedure of the European Pharmacopoeia for the sodium hydroxide titrant to decrease the systematic errors caused by carbon dioxide has also been evaluated.

  12. Alloy 22 Localized Corrosion Susceptibility In Aqueous Solutions Of Chloride And Nitrate Salts Of Sodium And Potassium At 110 - 150?C

    SciTech Connect

    Felker, S; Hailey, P D; Lian, T; Staggs, K J; Gdowski, G E

    2006-01-17

    Alloy 22 (a nickel-chromium-molybdenum-tungsten alloy) is being investigated for use as the outer barrier of waste containers for a high-level nuclear waste repository in the thick unsaturated zone at Yucca Mountain, Nevada. Experiments were conducted to assess crevice corrosion of Alloy 22 in de-aerated aqueous solutions of chloride and nitrate salts of potassium and sodium in the temperature range 110-150 C (some limited testing was also conducted at 90 C). Electrochemical tests were run in neutral salt solutions without acid addition and others were run in salt solutions with an initial hydrogen ion concentration of 10{sup -4} molal. The Alloy 22 specimens were weld prism specimens and de-aeration was performed with nitrogen gas. No evidence of crevice corrosion was observed in the range 125-150 C. In the 120 to 160 C temperature range, the anionic concentration of stable aqueous solutions is dominated by nitrate relative to chloride. At nominally 120 C, the minimum nitrate to chloride ratio is about 4.5, and it increases to about 22 at nominally 155 C. The absence of localized corrosion susceptibility in these solutions is attributed to the known inhibiting effect of the nitrate anion. At 110 C, aqueous solutions can have dissolved chloride in excess of nitrate. Localized corrosion was observed at nitrate to chloride ratios up to 1.0, the highest ratio tested. The extent of localized corrosion was confined to the crevice region of the samples, and was limited for nitrate to chloride ratios greater than or equal to 0.3. Aqueous solution chemistry studies indicate that nitrate to chloride ratios of less than 0.5 are possible for temperatures up to nominally 116 C. However, the exact upper temperature limit is unknown and no electrochemical testing was done at these temperatures. Limited comparison between 8 m Cl aqueous solutions of Na + K on the one hand and Ca on the other indicated similar electrochemical E{sub crit} values and similar morphology of attack

  13. The structures of the isomorphous potassium and rubidium salts of 4-nitrobenzoic acid and an overview of the metal complex stereochemistries of the alkali metal salt series with this ligand.

    PubMed

    Smith, Graham

    2015-06-01

    4-Nitrobenzoic acid (PNBA) has proved to be a useful ligand for the preparation of metal complexes but the known structures of the alkali metal salts of PNBA do not include the rubidium salt. The structures of the isomorphous potassium and rubidium polymeric coordination complexes with PNBA, namely poly[μ2-aqua-aqua-μ3-(4-nitrobenzoato)-potassium], [K(C7H4N2O2)(H2O)2]n, (I), and poly[μ3-aqua-aqua-μ5-(4-nitrobenzoato)-rubidium], [Rb(C7H4N2O2)(H2O)2]n, (II), have been determined. In (I), the very distorted KO6 coordination sphere about the K(+) centres in the repeat unit comprise two bridging nitro O-atom donors, a single bridging carboxylate O-atom donor and two water molecules, one of which is bridging. In Rb complex (II), the same basic MO6 coordination is found in the repeat unit, but it is expanded to RbO9 through a slight increase in the accepted Rb-O bond-length range and includes an additional Rb-O(carboxylate) bond, completing a bidentate O,O'-chelate interaction, and additional bridging Rb-O(nitro) and Rb-O(water) bonds. The comparative K-O and Rb-O bond-length ranges are 2.7352 (14)-3.0051 (14) and 2.884 (2)-3.182 (2) Å, respectively. The structure of (II) is also isomorphous, as well as isostructural, with the known structure of the nine-coordinate caesium 4-nitrobenzoate analogue, (III), in which the Cs-O bond-length range is 3.047 (4)-3.338 (4) Å. In all three complexes, common basic polymeric extensions are found, including two different centrosymmetric bridging interactions through both water and nitro groups, as well as extensions along c through the para-related carboxylate group, giving a two-dimensional structure in (I). In (II) and (III), three-dimensional structures are generated through additional bridges involving the nitro and water O atoms. In all three structures, the two water molecules are involved in similar intra-polymer O-H...O hydrogen-bonding interactions to both carboxylate and water O-atom acceptors. A

  14. Diagnosis of sources of current inefficiency in industrial molten salt electrolysis cells by Raman spectroscopy: A topical report on chlorides: Topical report, June 1982-June 1987

    SciTech Connect

    Sadoway, D. R.

    1987-06-01

    Molten salt electrolysis, a very energy-intensive process, is used in the extraction of light metals. Aluminum production by the Hall process and magnesium production in the Dow and I.G. Farbenindustrie cells constitute the major commercial applications of metal electrowinning from molten-salt media at present. The energy input into the electrolysis cell is in the form of direct current, and the energy efficiencies in the magnesium or aluminum processes are only in the 30 to 40% range. Major energy reductions are achieved by reducing the cell voltage or by increasing the current efficiency. Goal of the research is to identify the sources of the current losses occurring in molten salt electrolysis. This research worked on the systems of I.G. Farben magnesium chloride and Alcoa smelting aluminum chloride processes. Raman spectra were measured and analyzed for each component or their mixtures of the electrolyte for magnesium and aluminum reduction in chloride melts. Raman measurements were also conducted on the melts of industrial composition for aluminum and magnesium electrolysis. In laboratory-scale cells which imitated industrial practice, Raman spectra were measured in situ during electrolysis in attempts to identify the streamers, coloration of electrolyte, and any subvalent species. They were known to occur only during electrolysis, and they have been reported to be possible current losses. Cyclic voltammetry was conducted to obtain information about the generation of subvalent species which were not detected by Raman measurement. These were thought to be kinetic entities present only during electrolysis. Results of Raman spectroscopy and electrochemistry of magnesium and aluminum reduction from molten chloride bath are presented. The results would be useful to establish the basis for the study of electrolysis of aluminum from molten fluoride media. 119 refs., 66 figs.

  15. FUSED SALT PROCESS FOR RECOVERY OF VALUES FROM USED NUCLEAR REACTOR FUELS

    DOEpatents

    Moore, R.H.

    1960-08-01

    A process is given for recovering plutonium from a neutron-irradiated uranium mass (oxide or alloy) by dissolving the mass in an about equimolar alkali metalaluminum double chloride, adding aluminum metal to the mixture obtained at a temperature of between 260 and 860 deg C, and separating a uranium-containing metal phase and a plutonium-chloride- and fission-product chloridecontaining salt phase. Dissolution can be expedited by passing carbon tetrachloride vapors through the double salt. Separation without reduction of plutonium from neutron- bombarded uranium and that of cerium from uranium are also discussed.

  16. Kinetic study of the α-tocopherol-regeneration reaction of ubiquinol-10 in methanol and acetonitrile solutions: notable effect of the alkali and alkaline earth metal salts on the reaction rates.

    PubMed

    Mukai, Kazuo; Oi, Masanori; Ouchi, Aya; Nagaoka, Shin-ichi

    2012-03-01

    A kinetic study of regeneration reaction of α-tocopherol (α-TocH) by ubiquinol-10 has been performed in the presence of four kinds of alkali and alkaline earth metal salts (LiClO(4), NaClO(4), NaI, and Mg(ClO(4))(2)) in methanol and acetonitrile solutions, using double-mixing stopped-flow spectrophotometry. The second-order rate constants (k(r)'s) for the reaction of α-tocopheroxyl (α-Toc•) radical with ubiquinol-10 increased and decreased notably with increasing concentrations of metal salts in methanol and acetonitrile, respectively. The k(r) values increased in the order of no metal salt < NaClO(4) ~ NaI < LiClO(4) < Mg(ClO(4))(2) at the same concentration of metal salts in methanol. On the other hand, in acetonitrile, the k(r) values decreased in the order of no metal salt > NaClO(4) ~ NaI > LiClO(4) > Mg(ClO(4))(2) at the same concentration of metal salts. The metal salts having a smaller ionic radius of cation and a larger charge of cation gave a larger k(r) value in methanol, and a smaller k(r) value in acetonitrile. The effect of anion was almost negligible in both the solvents. Notable effects of metal cations on the UV-vis absorption spectrum of α-Toc• radical were observed in aprotic acetonitrile solution, suggesting complex formation between α-Toc• and metal cations. On the other hand, effects of metal cations were negligible in protic methanol, suggesting that the complex formation between α-Toc• and metal cations is hindered by the hydrogen bond between α-Toc• and methanol molecules. The difference between the reaction mechanisms in methanol and acetonitrile solutions was discussed on the basis of the results obtained. High concentrations of alkali and alkaline earth metal salts coexist with α-TocH and ubiquinol-10 in plasma, blood, and many tissues, suggesting the contribution of the metal salts to the above regeneration reaction in biological systems.

  17. The dangerous new synthetic drug α-PVP as the hydrated chloride salt α-pyrrolidinopentiophenone hydrochloride 0.786-hydrate.

    PubMed

    Wood, Matthew R; Bernal, Ivan; Lalancette, Roger A

    2016-01-01

    α-Pyrrolidinovalerophenone (α-PVP), a dangerous designer drug, is now being marketed around the world as a harmless `bath salt', when in reality it is a powerful β-ketone phenethylamine stimulant. A sample of the free base from a recent law-enforcement seizure was crystallized as the HCl salt [systematic name: 1-(1-oxo-1-phenylpentan-2-yl)pyrrolidin-1-ium chloride 0.786-hydrate], C15H22NO(+)·Cl(-)·0.786H2O. In the crystal structure, the propyl chain is nearly perpendicular to both the phenyl ring and the carbonyl group. The hydrogen-bonding scheme involves the quaternary N atom, the Cl(-) anion and the partially occupied (0.786) water molecule, forming centrosymmetric dimers.

  18. Dietary salt modulates the sodium chloride cotransporter expression likely through an aldosterone-mediated WNK4-ERK1/2 signaling pathway.

    PubMed

    Lai, Lingyun; Feng, Xiuyan; Liu, Defeng; Chen, Jing; Zhang, Yiqian; Niu, Bowen; Gu, Yong; Cai, Hui

    2012-03-01

    WNK is a serine/threonine kinase. Mutation in WNK1 or WNK4 kinase results in pseudohypoaldosteronism type II (PHA II) featuring hypertension, hyperkalemia and metabolic acidosis. Sodium chloride cotransporter (NCC) is known to be regulated by phosphorylation and trafficking. Dietary salt and hormonal stimulation, such as aldosterone, also affect the regulation of NCC. We have previously reported that WNK4 inhibits NCC protein expression. To determine whether dietary salt affects NCC abundance through WNK4-mediated mechanism, we investigated the effects of dietary salt change with or without aldosterone infusion (1 mg/kg/day) on NCC and WNK4 expression in rats. We found that high-salt (HS, 4% NaCl) diet significantly inhibits NCC mRNA expression and protein abundance while enhancing WNK4 mRNA and protein expression, whereas low-salt (LS, 0.07% NaCl) diet increases NCC mRNA expression and protein abundance while reducing WNK4 expression. We also found that aldosterone infusion in HS-fed rats increases NCC mRNA expression and protein abundance, but decreases WNK4 expression. Administration with spironolactone (0.1 g/kg/day) in LS-fed rats decreases NCC mRNA expression and protein abundance while increasing WNK4 expression. We further showed that ERK1/2 phosphorylation was increased in HS-fed rats, but decreased in LS-fed rats. In HEK293 cells, over-expressed WNK4 increases ERK1/2 phosphorylation, whereas knockdown of WNK4 expression decreases ERK1/2 phosphorylation. Aldosterone treatment for 3 h decreases ERK1/2 phosphorylation. These data suggest that dietary salt change affects NCC protein abundance in an aldosterone-dependent mechanism likely via the WNK4-ERK1/2-mediated pathway.

  19. Diphenylbutylbenzyl- and diphenyldibenzylphosphonium chlorides are interfacial catalysts in cross-linking of fluorine-containing copolymers

    SciTech Connect

    Lavrova, L.N.; Bondarenko, N.A.; Tsvetkov, E.N.; Nudel'man, Z.N.

    1988-09-10

    Vulcanization in a two-phase system with an interfacial transfer catalyst (ITC) is widely used for obtaining highly thermostable rubbers from fluorine-containing rubbers, copolymers of vinylidene fluoride with hexafluoropropylene. A simple method of synthesis of tertiary diphenylalkylphosphines by alkylation of diphenylphosphine with alkyl halides in the presence of an aqueous alkali and aprotic bipolar solvents (dimethyl sulfide, dimethylformamide, and hexamethanol) has now been developed. They synthesized diphenylbutyl- and diphenylbenzylphosphines by this method, and they were subsequently transformed into the corresponding phosphonium salts by treatment with an excess of benzyl chloride. The prepared diphenylbutylbenzyl- and diphenyldibenzyl- phosphonium chlorides were tested as ITC in vulcanization of SKF-26 fluorine-containing rubber.

  20. Ammonium chloride salting out extraction/cleanup for trace-level quantitative analysis in food and biological matrices by flow injection tandem mass spectrometry.

    PubMed

    Nanita, Sergio C; Padivitage, Nilusha L T

    2013-03-20

    A sample extraction and purification procedure that uses ammonium-salt-induced acetonitrile/water phase separation was developed and demonstrated to be compatible with the recently reported method for pesticide residue analysis based on fast extraction and dilution flow injection mass spectrometry (FED-FI-MS). The ammonium salts evaluated were chloride, acetate, formate, carbonate, and sulfate. A mixture of NaCl and MgSO4, salts used in the well-known QuEChERS method, was also tested for comparison. With thermal decomposition/evaporation temperature of <350°C, ammonium salts resulted in negligible ion source residual under typical electrospray conditions, leading to consistent method performance and less instrument cleaning. Although all ammonium salts tested induced acetonitrile/water phase separation, NH4Cl yielded the best performance, thus it was the preferred salting out agent. The NH4Cl salting out method was successfully coupled with FI/MS/MS and tested for fourteen pesticide active ingredients: chlorantraniliprole, cyantraniliprole, chlorimuron ethyl, oxamyl, methomyl, sulfometuron methyl, chlorsulfuron, triflusulfuron methyl, azimsulfuron, flupyrsulfuron methyl, aminocyclopyrachlor, aminocyclopyrachlor methyl, diuron and hexazinone. A validation study was conducted with nine complex matrices: sorghum, rice, grapefruit, canola, milk, eggs, beef, urine and blood plasma. The method is applicable to all analytes, except aminocyclopyrachlor. The method was deemed appropriate for quantitative analysis in 114 out of 126 analyte/matrix cases tested (applicability rate=0.90). The NH4Cl salting out extraction/cleanup allowed expansion of FI/MS/MS for analysis in food of plant and animal origin, and body fluids with increased ruggedness and sensitivity, while maintaining high-throughput (run time=30s/sample). Limits of quantitation (LOQs) of 0.01mgkg(-1) (ppm), the 'well-accepted standard' in pesticide residue analysis, were achieved in >80% of cases tested; while

  1. Formation of Na2SO4 and K2SO4 in flames doped with sulfur and alkali chlorides and carbonates

    NASA Technical Reports Server (NTRS)

    Fryburg, G. C.; Miller, R. A.; Stearns, C. A.; Kohl, F. J.

    1977-01-01

    High pressure, free-jet expansion, mass spectrometric sampling was used to identify directly and to measure reaction products formed in doped methane-oxygen flames. Flames were doped with SO2 or CH3SH and sodium or potassium chlorides or carbonates. Gaseous Na2SO4 or K2SO4 molecules were formed in residence times on the order of 1 msec for each combination of dopants used. Composition profiles of combustion products were measured and compared with equilibrium thermodynamic calculations of product composition.

  2. Formation of Na2SO4 and K2SO4 in flames doped with sulfur and alkali chlorides and carbonates

    NASA Technical Reports Server (NTRS)

    Fryburg, G. C.; Miller, R. A.; Stearns, C. A.; Kohl, F. J.

    1977-01-01

    High pressure, free-jet expansion, mass spectrometric sampling was used to identify directly and to measure reaction products formed in doped methane-oxygen flames. Flames were doped with SO2 or CH3SH and sodium or potassium chlorides or carbonates. Gaseous NA2SO4 or K2S04 molecules were formed in residence times on the order of msec for each combination of dopants used. Composition profiles of combustion products were measured and compared with equilibrium thermodynamic calculations of product composition.

  3. Laboratory studies of the low-temperature deliquescence of calcium chloride salts: Relevance to aqueous solutions on Mars and in the Antarctic Dry Valleys

    NASA Astrophysics Data System (ADS)

    Gough, R. V.; Chevrier, V.; Tolbert, M. A.

    2013-12-01

    There is significant interest in the possible existence of liquid water on current Mars. This water would likely exist as a brine in order to be stable on Mars today. It has been proposed that soil salts could form aqueous solutions through either the melting of ice by low-eutectic salts, or by the deliquescence of hygroscopic salts present in the Martian soil. The focus thus far has largely been on perchlorate species, which can melt ice at temperatures as low as 206 K and can deliquesce at relative humidity values as low as 38% RH. A Mars-relevant salt that has been neglected thus far is calcium chloride (CaCl2). Calcium has been reported to be an abundant cation at the Phoenix landing site and Mars Science Laboratory instruments have recently identified calcium as well. Simulations suggest subsurface CaCl2 is an ideal candidate to produce brines with seasonality consistent with observed recurring slope lineae (RSL) (Chevrier et al., 2012). Finally, the only terrestrial site where RSL-like features have been observed (near Don Juan Pond in the Antarctic Dry Valleys) contains abundant CaCl2. These seasonal slope streaks are thought to form when CaCl2 in the soil deliquesces due to contact with atmospheric water vapor (Dickson et al., 2013). It is important to understand how this CaCl2 interacts with water vapor at low temperatures relevant to Mars and the Martian analog sites. Here we use a Raman microscope and environmental cell to monitor the low-temperature (223 - 273 K) deliquescence (solid to aqueous phase transition) and efflorescence (aqueous to solid phase transition) of three hydration states of CaCl2 (dihydrate, tetrahydrate, hexahydrate). We have found that the deliquescence relative humidity (DRH) increases with increasing hydration state, which is an expected result. Average DRH values over the temperature range studied are 20.0 × 2.6% RH for the dihydrate, 31.8 × 6.3% RH for the tetrahydrate and 60.7 × 1.6% RH for the hexahydrate. Once the aqueous

  4. Deliquescence-induced wetting and RSL-like darkening of a Mars analogue soil containing various perchlorate and chloride salts

    NASA Astrophysics Data System (ADS)

    Heinz, Jacob; Schulze-Makuch, Dirk; Kounaves, Samuel P.

    2016-05-01

    Recurring slope lineae (RSL) are flow-like features on Mars characterized by a local darkening of the soil thought to be generated by the formation and flow of liquid brines. One possible mechanism responsible for forming these brines could be the deliquescence of salts present in the Martian soil. We show that the JSC Mars-1a analogue soil undergoes a darkening process when salts dispersed in the soil deliquesce, but forming continuous liquid films and larger droplets takes much longer than previously assumed. Thus, RSL may not necessarily require concurrent flowing liquid water/brine or a salt-recharge mechanism, and their association with gullies may be the result of previously flowing water and deposited salts during an earlier warmer and wetter period. In addition, our results show that electrical conductivity measurements correlate well with the deliquescence rates and provide better overall characterization than either Raman spectroscopy or estimates based on deliquescence relative humidity.

  5. Cyclic Voltammetry of Silver Chloride in Lithium Chloride-Potassium Chloride Eutectic.

    DTIC Science & Technology

    TRY), Fused salts, Silver, Reduction(Chemistry), Dissolving, ChloridesSilver chloride, Cyclic voltammetry , *VoltammetryThe technique of cyclic ... voltammetry was employed to study the deposition and dissolution of silver metal at platinum wire electrodes in molten lithium chloride-potassium chloride

  6. 21 CFR 184.1138 - Ammonium chloride.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... GRAS § 184.1138 Ammonium chloride. (a) Ammonium chloride (NH4Cl, CAS Reg. No. 12125-02-9) is produced by the reaction of sodium chloride and an ammonium salt in solution. The less soluble sodium salt... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Ammonium chloride. 184.1138 Section 184.1138...

  7. Combined effect of concentrations of algal food (Chlorella vulgaris) and salt (sodium chloride) on the population growth of Brachionus calyciflorus and Brachionus patulus (Rotifera).

    PubMed

    Peredo-Alvarez, Víctor M; Sarma, S S; Nandini, S

    2003-06-01

    Salinity is an important variable influencing the density and diversity of rotifers. Studies on salt tolerance of rotifers have so far concentrated on euryhaline species while very little information is available on non-euryhaline taxa. In the present work, we have evaluated the combined effects of Chlorella vulgaris and sodium chloride on the population growth of two freshwater rotifers B. calyciflorus and B. patulus. A 24 hr acute tolerance test using NaCl revealed that B. calyciflorus was more resistant (LC50 = 3.75 +/- 0.04 g l-1) than B. patulus (2.14 +/- 0.09 g l-1). The maximal population density (mean +/- standard error) for B. calyciflorus in the control at 4.5 x 10(6) cells ml-1 (algal level) was 80 +/- 5 ind. ml-1, which was nearly a fifth of the one for B. patulus (397 +/- 7 ind. ml-1) under comparable conditions. Data on population growth revealed that regardless of salt concentration, the density of B. calyciflorus increased with increasing food levels, while for B. patulus, this trend was evident only in the controls. Regardless of salt concentration and algal food level, the day of maximal population density was lower (4 +/- 0.5 days) for B. calyciflorus than for B. patulus (11 +/- 1 day). The highest rates of population increase (r values) for B. calyciflorus and B. patulus were 0.429 +/- 0.012 and 0.367 +/- 0.004, respectively, recorded at 4.5 x 10(6) cells ml-1 of Chlorella in the controls. The protective role of algae in reducing the effect of salt stress was more evident in B. calyciflorus than B. patulus.

  8. Counterion influence on the vibrational wavenumbers in ternary and quaternary metal hydride salts, A2MH6 (A = alkali metal, alkaline earth, and lanthanides; M = Ir, Fe, Ru, Os, Pt, Mn).

    PubMed

    Gilson, Denis F R; Moyer, Ralph O

    2012-02-06

    The wavenumbers of the ν(3) metal-hydrogen stretching mode (T(1u)) in the IR spectra of both ternary and quaternary hexahydrido salts of transition metals from groups 7 to 10 ([Mn(I)H(6)](5-), [Fe(II)H(6)](4-), [Ru(II)H(6)](4-), [Os(II)H(6)](4-), [Ir(III)H(6)](3-), and [Pt(IV)H(6)](2-)) depend linearly upon the ionization energies of the counterions (alkali metal, alkaline earth, and lanthanide) with a separate line for each metal. This relationship provides quantitative support for the charge-transfer mechanism for explaining the stabilities of these compounds.

  9. Method for the safe disposal of alkali metal

    DOEpatents

    Johnson, Terry R.

    1977-01-01

    Alkali metals such as those employed in liquid metal coolant systems can be safely reacted to form hydroxides by first dissolving the alkali metal in relatively inert metals such as lead or bismuth. The alloy thus formed is contacted with a molten salt including the alkali metal hydroxide and possibly the alkali metal carbonate in the presence of oxygen. This oxidizes the alkali metal to an oxide which is soluble within the molten salt. The salt is separated and contacted with steam or steam-CO.sub.2 mixture to convert the alkali metal oxide to the hydroxide. These reactions can be conducted with minimal hydrogen evolution and with the heat of reaction distributed between the several reaction steps.

  10. Effects of road salts on groundwater and surface water dynamics of socium and chloride in an urban restored stream

    EPA Science Inventory

    Road salts are a growing environmental concern in urban watersheds. We examined groundwater (GW) and surface water (SW) dynamics of Na+ and Cl− in Minebank Run (MBR), an urban stream in Maryland, USA. We observed an increasing salinity trend in this restored stream. Current basef...

  11. Mercuric chloride poisoning

    MedlinePlus

    ... Mercuric chloride is a very poisonous form of mercury. It is a type of mercury salt. There are different types of mercury poisonings . This article discusses poisoning from swallowing mercuric ...

  12. Vitrification of IFR and MSBR halide salt reprocessing wastes

    SciTech Connect

    Siemer, D.D.

    2013-07-01

    Both of the genuinely sustainable (breeder) nuclear fuel cycles (IFR - Integral Fast Reactor - and MSBR - Molten Salt Breeder Reactor -) studied by the USA's national laboratories would generate high level reprocessing waste (HLRW) streams consisting of a relatively small amount ( about 4 mole %) of fission product halide (chloride or fluoride) salts in a matrix comprised primarily (about 95 mole %) of non radioactive alkali metal halide salts. Because leach resistant glasses cannot accommodate much of any of the halides, most of the treatment scenarios previously envisioned for such HLRW have assumed a monolithic waste form comprised of a synthetic analog of an insoluble crystalline halide mineral. In practice, this translates to making a 'substituted' sodalite ('Ceramic Waste Form') of the IFR's chloride salt-based wastes and fluoroapatite of the MSBR's fluoride salt-based wastes. This paper discusses my experimental studies of an alternative waste management scenario for both fuel cycles that would separate/recycle the waste's halide and immobilize everything else in iron phosphate (Fe-P) glass. It will describe both how the work was done and what its results indicate about how a treatment process for both of those wastes should be implemented (fluoride and chloride behave differently). In either case, this scenario's primary advantages include much higher waste loadings, much lower overall cost, and the generation of a product (glass) that is more consistent with current waste management practices. (author)

  13. Determination of activity coefficient of lanthanum chloride in molten LiCl-KCl eutectic salt as a function of cesium chloride and lanthanum chloride concentrations using electromotive force measurements

    NASA Astrophysics Data System (ADS)

    Bagri, Prashant; Simpson, Michael F.

    2016-12-01

    The thermodynamic behavior of lanthanides in molten salt systems is of significant scientific interest for the spent fuel reprocessing of Generation IV reactors. In this study, the apparent standard reduction potential (apparent potential) and activity coefficient of LaCl3 were determined in a molten salt solution of eutectic LiCl-KCl as a function of concentration of LaCl3. The effect of adding up to 1.40 mol % CsCl was also investigated. These properties were determined by measuring the open circuit potential of the La-La(III) redox couple in a high temperature molten salt electrochemical cell. Both the apparent potential and activity coefficient exhibited a strong dependence on concentration. A low concentration (0.69 mol %) of CsCl had no significant effect on the measured properties, while a higher concentration (1.40 mol %) of CsCl caused an increase (become more positive) in the apparent potential and activity coefficient at the higher range of LaCl3 concentrations.

  14. Fermentation profiles of Manzanilla-Aloreña cracked green table olives in different chloride salt mixtures.

    PubMed

    Bautista-Gallego, J; Arroyo-López, F N; Durán-Quintana, M C; Garrido-Fernández, A

    2010-05-01

    NaCl plays an important role in table olive processing affecting the flavour and microbiological stability of the final product. However, consumers demand foods low in sodium, which makes necessary to decrease levels of this mineral in fruits. In this work, the effects of diverse mixtures of NaCl, CaCl(2) and KCl on the fermentation profiles of cracked directly brined Manzanilla-Aloreña olives, were studied by means of response surface methodology based in a simplex lattice mixture design with constrains. All salt combinations led to lactic acid processes. The growth of Enterobacteriaceae populations was always limited and partially inhibited by the presence of CaCl(2). Only time to reach half maximum populations and decline rates of yeasts, which were higher as concentrations of NaCl or KCl increased, were affected, and correspondingly modelled, as a function of salt mixtures. However, lactic acid bacteria growth parameters could not be related to initial environmental conditions. They had a longer lag phase, slower growth and higher population levels than yeasts. Overall, the presence of CaCl(2) led to a slower Enterobacteriaceae and lactic acid bacteria growth than the traditional NaCl brine but to higher yeast activity. The presence of CaCl(2) in the fermentation brines also led to higher water activity, lower pH and combined acidity as well as a faster acidification while NaCl and KCl had fairly similar behaviours. Apparently, NaCl may be substituted in diverse proportions with KCl or CaCl(2) without substantially disturbing water activity or the usual fermentation profiles while producing olives with lower salt content.

  15. Production of anhydrous aluminum chloride composition

    DOEpatents

    Vandergrift, G.F. III; Krumpelt, M.; Horwitz, E.P.

    1981-10-08

    A process is described for producing an anhydrous aluminum chloride composition from a water-based aluminous material such as a slurry of aluminum hydroxide in a multistage extraction process in which the aluminum ion is first extracted into an organic liquid containing an acidic extractant and then extracted from the organic phase into an alkali metal chloride or chlorides to form a melt containing a mixture of chlorides of alkali metal and aluminum. In the process, the organic liquid may be recycled. In addition, the process advantageously includes an electrolysis cell for producing metallic aluminum and the alkali metal chloride or chlorides may be recycled for extraction of the aluminum from the organic phase.

  16. Effect of the salt-induced micellar microstructure on the nonlinear shear flow behavior of ionic cetylpyridinium chloride surfactant solutions

    NASA Astrophysics Data System (ADS)

    Gaudino, D.; Pasquino, R.; Kriegs, H.; Szekely, N.; Pyckhout-Hintzen, W.; Lettinga, M. P.; Grizzuti, N.

    2017-03-01

    The shear flow dynamics of linear and branched wormlike micellar systems based on cetylpyridinium chloride and sodium salicylate in brine solution is investigated through rheometric and scattering techniques. In particular, the flow and the structural flow response are explored via velocimetry measurements and rheological and rheometric small-angle neutron scattering (SANS) experiments, respectively. Although all micellar solutions display a similar shear thinning behavior in the nonlinear regime, the experimental results show that shear banding sets in only when the micelle contour length L ¯ is sufficiently long, independent of the nature of the micellar connections (either linear or branched micelles). Using rheometric SANS, we observe that the shear banding systems both show very similar orientational ordering as a function of Weissenberg number, while the short branched micelles manifest an unexpected increase of ordering at very low Weissenberg numbers. This suggests the presence of an additional flow-induced relaxation process that is peculiar for branched systems.

  17. Hydrogen bonding motifs, spectral characterization, theoretical computations and anticancer studies on chloride salt of 6-mercaptopurine: An assembly of corrugated lamina shows enhanced solubility

    NASA Astrophysics Data System (ADS)

    Suresh Kumar, S.; Athimoolam, S.; Sridhar, B.

    2015-10-01

    6-Mercaptopurine (an anti cancer drug), is coming under the class II Biopharmaceutics Classification System (BCS). In order to enhance the solubility with retained physiochemical/pharmaceutical properties, the present work was attempted with its salt form. The single crystals of 6-mercaptopurinium chloride (6MPCl) were successfully grown by slow evaporation technique under ambient temperature. The X-ray diffraction study shows that the crystal packing is dominated by N-H⋯Cl classical hydrogen bonds leading to corrugated laminar network. The hydrogen bonds present in the lamina can be dismantled as three chain C21(6), C21(7) and C21(8) motifs running along ab-diagonal of the unit cell. These primary chain motifs are interlinked to each other forming ring R63(21) motifs. These chain and ring motifs are aggregated like a dendrimer structure leading to the above said corrugated lamina. This low dimensional molecular architecture differs from the ladder like arrays in pure drug though it possess lattice water molecule in lieu of the chloride anion in the present compound. Geometrical optimizations of 6MPCl were done by Density Functional Theory (DFT) using B3LYP function with two different basis sets. The optimized molecular geometries and computed vibrational spectra are compared with their experimental counterparts. The Natural Bond Orbital (NBO) analysis was carried out to interpret hyperconjugative interaction and Intramolecular Charge Transfer (ICT). The chemical hardness, electronegativity, chemical potential and electrophilicity index of 6MPCl were found along with the HOMO-LUMO plot. The lower band gap value obtained from the Frontier Molecular Orbital (FMO) analysis reiterates the pharmaceutical activity of the compound. The anticancer studies show that 6MPCl retains its activity against human cervical cancer cell line (HeLa). Hence, this anticancer efficacy and improved solubility demands 6MPCl towards the further pharmaceutical applications.

  18. Formation of N,N,N‧,N‧-tetramethylformamidinium disulphide from the chemical and electrochemical oxidation of tetramethylthiourea: Vibrational spectra and crystal structure of the chloride dihydrate salt

    NASA Astrophysics Data System (ADS)

    Bolzán, A. E.; Güida, J. A.; Piatti, R. C. V.; Arvia, A. J.; Piro, O. E.; Sabino, J. R.; Castellano, E. E.

    2007-12-01

    The N, N, N', N'-tetramethylformamidinium disulphide (TMFDS) was prepared from either the electro-oxidation of tetramethylthiourea (TMTU) on platinum electrodes in aqueous perchloric acid solution or the chemical oxidation of TMTU with hydrogen peroxide in hydrochloric acid-containing absolute ethanol. The electrochemical formation of TMFDS at different potentials was followed by in situ FTIRRAS spectroscopy. The IR and Raman spectra of TMFDS chemically formed as a chloride dihydrate were determined and compared to the product produced electrochemically. The crystal structure of the chloride salt [N(CH 3) 2] 2C dbnd S sbnd S dbnd C [N(CH 3) 2] 2Cl 2·2H 2O, as determined by X-ray diffraction, crystallises in the monoclinic C2/ c space group with a = 23.267(1), b = 10.824(1), c = 17.774(1) Å, β = 126.91(1)°, and Z = 8. The structure was solved from 2489 reflections with I > 2 σ( I) and refined to an agreement R1-factor of 0.0405. The two molecular halves of the dimeric [N(CH)2]2C dbnd S sbnd S dbnd C [N(CH)2]22+ ion are linked by a disulphide single bond [ d(S sbnd S) = 2.0454(9) Å] and related to each other by a non-crystallographic pseudo two-fold axis. DFT structure optimisation and normal mode frequencies were calculated using the 6-311G(d,f) basis set at DFT theory level. An estimation of the free energy for the dimer formation and rate ratio for the homogeneous and heterogeneous processes are presented. These data are consistent with the electrochemical mechanism of the anodic formation of TMFDS 2+ from TMTU electro-oxidation in acid solutions.

  19. Chloride salt of conducting polyaniline synthesized in the presence of CeO2: Structural analysis of the core-shell nanocomposite

    NASA Astrophysics Data System (ADS)

    da Silva, J. S. M.; de Souza, S. M.; Trovati, G.; Sanches, E. A.

    2017-01-01

    Chloride salt of conducting Polyaniline (ES-PANI) was synthesized in the presence of cerium dioxide (CeO2) for structural and morphological evaluation of the resulting core-shell nanocomposite. X-ray Diffraction (XRD), estimative of crystallinity percentage, Le Bail Method, Scanning Electron Microscopy (SEM) and DC electrical conductivity were used for materials characterization. The resulting nanocomposite was constituted of three phases as identified by X-Ray Diffraction: ES-PANI, CeO2 and CeCl3(H2O)7, chloride hepta-hydrate cerium. Crystallinity of ES-PANI and nanocomposite were estimated around 40 and 85%, respectively. XRD patterns were also used to perform the Le Bail Method. This refinement allowed structural characterization of each phase, obtainment of cell parameters and crystallite size and shape. For ES-PANI and CeCl3(H2O)7, crystallites showed a prolate-like shape with an average size of 21 Å and 104 Å, respectively. CeO2 crystallites presented much larger size, as expected, with isotropic average size of 490 Å. SEM images showed that the nanocomposite has a core-shell morphology with both ES-PANI nanofibers and CeCl3(H2O)7 particles coating the CeO2 particles. The polymerization of ES-PANI over the CeO2 particles in order to form the nanocomposite affected the natural chain alignment of the polymer, resulting in better molecular rearrangement and larger crystallites. Finally, measurements of DC electrical conductivity of ES-PANI and nanocomposite have showed values of 1.11 × 10-4 and 2.22 × 10-4 S/cm, respectively. Nanocomposite has showed electrical conductivity 50 times greater than the pure ES-PANI. Thus, in this work we have reported a systematic structural and morphological investigation of PANI/CeO2/CeCl3(H2O)7 core-shell nanocomposite.

  20. Individual differences in sour and salt sensitivity: detection and quality recognition thresholds for citric acid and sodium chloride.

    PubMed

    Wise, Paul M; Breslin, Paul A S

    2013-05-01

    Taste sensitivity is assessed with various techniques, including absolute detection and quality recognition. For any stimulus, one might expect individual differences in sensitivity to be reflected in all measures, but they are often surprisingly independent. Here, we focus on sensitivity to sour and salty taste, in part because processing of these qualities is poorly understood relative to other tastes. In Study 1, we measured retest reliability for detection (modified, forced-choice staircase method) and recognition (modified Harris-Kalmus procedure) for both citric acid (CA) and sodium chloride (NaCl). Despite good retest reliability, individual differences in detection and recognition were weakly correlated, suggesting that detection and recognition of sour and salty stimuli may reflect different physiological processes. In Study 2, a subset of subjects returned to contribute full detection (psychometric) functions for CA and NaCl. Thresholds estimated from full detection functions correlated with both staircase and recognition thresholds, suggesting that both tasks may reflect absolute sensitivity to some extent. However, the ranges of individual differences were systematically compressed for staircase thresholds relative to those from full detection functions. Thus, individual differences in sensitivity appear to interact with different test methodologies in lawful ways. More work will be required to understand how different taste phenotypes relate to one another.

  1. Electrochemical chloride extraction: efficiency and side effects

    SciTech Connect

    Orellan, J.C.; Escadeillas, G.; Arliguie, G

    2004-02-01

    Some specimens of reinforced concrete cast with an alkali-resistant aggregate, previously maintained in a solution of NaCl, were subjected to an electrochemical chloride extraction (ECE). The chloride profiles before and after treatment were determined. Likewise, alkali ions profiles before and after treatment were determined. After treatment, some specimens were stored in a controlled atmosphere (60 deg. C and 100% RH) in order to accelerate the alkali-silica reaction, if any. Results of chloride content after treatment show that about 40% of the initial chloride is removed within 7 weeks. About one-half of the chloride close to steel was removed, but at the same time, significant amounts of alkali ions were observed around the steel. Microstructural observations by scanning electron microscopy (SEM) showed that after treatment, new cementitious phases containing higher concentrations of sodium, aluminum and potassium were formed. Moreover, alkali-silica gel was observed in the specimens stored at 60 deg. C and 100% RH. It may be possible that the ECE accumulates locally high amounts of alkali ions that stimulate the alkali-silica reaction even though the concrete contained nominally inert siliceous aggregates. The specimen expansions were not recorded, but no cracks were observed.

  2. 21 CFR 184.1138 - Ammonium chloride.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    .... No. 12125-02-9) is produced by the reaction of sodium chloride and an ammonium salt in solution. The less soluble sodium salt separates out at elevated temperatures, and ammonium chloride is recovered... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Ammonium chloride. 184.1138 Section 184.1138...

  3. 21 CFR 184.1138 - Ammonium chloride.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    .... No. 12125-02-9) is produced by the reaction of sodium chloride and an ammonium salt in solution. The less soluble sodium salt separates out at elevated temperatures, and ammonium chloride is recovered... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Ammonium chloride. 184.1138 Section 184.1138...

  4. 21 CFR 184.1138 - Ammonium chloride.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    .... No. 12125-02-9) is produced by the reaction of sodium chloride and an ammonium salt in solution. The less soluble sodium salt separates out at elevated temperatures, and ammonium chloride is recovered... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ammonium chloride. 184.1138 Section 184.1138...

  5. 21 CFR 184.1138 - Ammonium chloride.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    .... No. 12125-02-9) is produced by the reaction of sodium chloride and an ammonium salt in solution. The less soluble sodium salt separates out at elevated temperatures, and ammonium chloride is recovered... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Ammonium chloride. 184.1138 Section 184.1138...

  6. Self-discharge in bimetallic cells containing alkali metal

    NASA Technical Reports Server (NTRS)

    Foster, M. S.; Hesson, J. C.; Shimotake, H.

    1969-01-01

    Theoretical analysis of thermally regenerative bimetallic cells with alkali metal anodes shows a relation between the current drawn and the rate of discharge under open-circuit conditions. The self-discharge rate of the cell is due to the dissolution and ionization of alkali metal atoms in the fused-salt electrolyte

  7. Method for intercalating alkali metal ions into carbon electrodes

    DOEpatents

    Doeff, M.M.; Ma, Y.; Visco, S.J.; DeJonghe, L.

    1995-08-22

    A low cost, relatively flexible, carbon electrode for use in a secondary battery is described. A method is provided for producing same, including intercalating alkali metal salts such as sodium and lithium into carbon.

  8. Method for intercalating alkali metal ions into carbon electrodes

    DOEpatents

    Doeff, Marca M.; Ma, Yanping; Visco, Steven J.; DeJonghe, Lutgard

    1995-01-01

    A low cost, relatively flexible, carbon electrode for use in a secondary battery is described. A method is provided for producing same, including intercalating alkali metal salts such as sodium and lithium into carbon.

  9. Spectroscopic (FT-IR, FT-Raman, UV absorption, 1H and 13C NMR) and theoretical (in B3LYP/6-311++G** level) studies on alkali metal salts of caffeic acid

    NASA Astrophysics Data System (ADS)

    Świsłocka, Renata

    The effect of some metals on the electronic system of benzoic and nicotinic acids has recently been investigated by IR, Raman and UV spectroscopy [1-3]. Benzoic and nicotinic acids are regarded model systems representing a wide group of aromatic ligands which are incorporated into enzymes. In this work the FT-IR (in solid state and in solution), FT-Raman, UV absorption and 1H and 13C NMR spectra of caffeic acid (3,4-dihydroxycinnamic acid) and its salts with lithium, sodium, potassium, rubidium and caesium were registered, assigned and analyzed. The effect of alkali metals on the electronic system of ligands was discussed. Studies of differences in the number and position of bands from the IR, Raman, UV absorption spectra and chemical shifts from NMR spectra allowed to conclude on the distribution of electronic charge in the molecules, the delocalization energy of π electrons and the reactivity of ligands in metal complexes. Optimized geometrical structures of studied compounds were calculated by B3LYP method using 6-311++G** basis set. Bond lengths, angles and dipole moments for the optimized structures of caffeic acid and lithium, sodium, potassium caffeinates were also calculated. The theoretical wavenumbers and intensities of IR spectra were obtained. The calculated parameters were compared to the experimental characteristics of investigated compounds. Microbial activity of studied compounds was tested against Escherichia coli, Pseudomonas aeruginosa, Staphylococcus aureus and Proteus vulgaris.

  10. Production of anhydrous aluminum chloride composition and process for electrolysis thereof

    DOEpatents

    Vandegrift, George F.; Krumpelt, Michael; Horwitz, E. Philip

    1983-01-01

    A process for producing an anhydrous aluminum chloride composition from a water-based aluminous material such as a slurry of aluminum hydroxide in a multistage extraction process in which the aluminum ion is first extracted into an organic liquid containing an acidic extractant and then extracted from the organic phase into an alkali metal chloride or chlorides to form a melt containing a mixture of chlorides of alkali metal and aluminum. In the process, the organic liquid may be recycled. In addition, the process advantageously includes an electrolysis cell for producing metallic aluminum and the alkali metal chloride or chlorides may be recycled for extraction of the aluminum from the organic phase.

  11. Alkali metal nitrate purification

    DOEpatents

    Fiorucci, Louis C.; Morgan, Michael J.

    1986-02-04

    A process is disclosed for removing contaminants from impure alkali metal nitrates containing them. The process comprises heating the impure alkali metal nitrates in solution form or molten form at a temperature and for a time sufficient to effect precipitation of solid impurities and separating the solid impurities from the resulting purified alkali metal nitrates. The resulting purified alkali metal nitrates in solution form may be heated to evaporate water therefrom to produce purified molten alkali metal nitrates suitable for use as a heat transfer medium. If desired, the purified molten form may be granulated and cooled to form discrete solid particles of purified alkali metal nitrates.

  12. Viability of Clostridium perfringens, Escherichia coli, and Listeria monocytogenes surviving mild heat or aqueous ozone treatment on beef followed by heat, alkali, or salt stress.

    PubMed

    Novak, John S; Yuan, James T C

    2003-03-01

    The threat of pathogen survival following ozone treatment of meat necessitates careful evaluation of the microorganisms surviving under such circumstances. The objective of this study was to determine whether sublethal aqueous ozone treatment (3 ppm of O3 for 5 min) of microorganisms on beef surfaces would result in increased or decreased survival with respect to subsequent heat, alkali, or NaCl stress. A mild heat treatment (55 degrees C for 30 min) was used for comparison. Reductions in three-strain cocktails of Clostridium perfringens, Escherichia coli O157:H7, and Listeria monocytogenes on beef following the heat treatment were 0.14, 0.77, and 1.47 log10 CFU/g, respectively, whereas reductions following ozone treatment were 1.28, 0.85, and 1.09 log10 CFU/g, respectively. C. perfringens cells exhibited elevated heat resistance at 60 degrees C (D60 [time at 60 degrees C required to reduce the viable cell population by 1 log10 units or 90%] = 17.76 min) following heat treatment of beef (55 degrees C for 30 min) but exhibited reduced viability at 60 degrees C following ozone treatment (D60 = 7.64 min) compared with the viability of untreated control cells (D60 = 13.84 min). The D60-values for L. monocytogenes and E. coli O157:H7 following heat and ozone exposures were not significantly different (P > 0.05). C. perfringens cells that survived ozone treatment did not exhibit increased resistance to pH (pH 6 to 12) relative to non-ozone-treated cells when grown at 37 degrees C for 24 h. The heat treatment also resulted in decreased numbers of surviving cells above and below neutral pH values for both E. coli O157:H7 and L. monocytogenes relative to those of non-heat-treated cells grown at 37 degrees C for 24 h. There were significant differences (P < 0.05) in C. perfringens reductions with increasing NaCl concentrations. The effects of NaCl were less apparent for E. coli and L. monocytogenes survivors. It is concluded that pathogens surviving ozone treatment of beef

  13. Long-term cement corrosion in chloride-rich solutions relevant to radioactive waste disposal in rock salt - Leaching experiments and thermodynamic simulations

    NASA Astrophysics Data System (ADS)

    Bube, C.; Metz, V.; Bohnert, E.; Garbev, K.; Schild, D.; Kienzler, B.

    Low- and intermediate-level radioactive wastes are frequently solidified in a cement matrix. In a potential repository for nuclear wastes, the cementitious matrix is altered upon contact with solution and the resulting secondary phases may provide for significant retention of the radionuclides incorporated in the wastes. In order to assess the secondary phases formed upon corrosion in chloride-rich solutions, which are relevant for nuclear waste disposal in rock salt, leaching experiments were performed. Conventional laboratory batch experiments using powdered hardened cement paste in MgCl2-rich solutions were left to equilibrate for up to three years and full-scale cemented waste products were exposed to NaCl-rich and MgCl2-rich solutions for more than twenty years, respectively. Solid phase analyses revealed that corrosion of hardened cement in MgCl2-rich solutions advanced faster than in NaCl-rich solutions due to the extensive exchange of Mg from solution against Ca from the cementitious solid. Thermodynamic equilibrium simulations compared well to results at the final stages of the respective experiments indicating that close to equilibrium conditions were reached. At high cement product to brine ratios (>0.65 g mL-1), the solution composition in the laboratory-scale experiments was close to that of the full-scale experiments (cement to brine ratio of 2.5 g mL-1) in the MgCl2 systems. The present study demonstrates the applicability of thermodynamic methods used in this approach to adequately describe full-scale long-term experiments with cemented waste simulates.

  14. Milk-alkali syndrome

    MedlinePlus

    ... this page: //medlineplus.gov/ency/article/000332.htm Milk-alkali syndrome To use the sharing features on this page, please enable JavaScript. Milk-alkali syndrome is a condition in which there ...

  15. Understanding the microcrystal tests of three related phenethylamines: the ortho-metallated (±)-amphetamine formed with gold(III) chloride, and the tetrachloridoaurate(III) salts of (+)-methamphetamine and (±)-ephedrine.

    PubMed

    Wood, Matthew R; Lalancette, Roger A

    2013-04-01

    The ortho-metallation product of the reaction of (±)-amphetamine with gold(III) chloride, [D,L-2-(2-aminopropyl)phenyl-κ(2)N,C(1)]dichloridogold(III), [Au(C9H12N)Cl2], and the two salts resulting from crystallization of (+)-methamphetamine with gold(III) chloride, D-methyl(1-phenylpropan-2-yl)azanium tetrachloridoaurate(III), (C10H16N)[AuCl4], and of (±)-ephedrine with gold(III) chloride, D,L-(1-hydroxy-1-phenylpropan-2-yl)(methyl)azanium tetrachloridoaurate(III), (C10H16NO)[AuCl4], have different structures. The first makes a bidentate complex directly with a dichloridogold(III) group, forming a six-membered ring structure; the second and third each form a salt with [AuCl4](-) (each has two formula units in the asymmetric unit). The organic components are all members of the same class of stimulants that are prevalent in illicit drug use. These structures are important contributions to the understanding of the microcrystal tests for these drugs that have been employed for well over 100 years.

  16. Solution-derived sodalite made with Si- and Ge-ethoxide precursors for immobilizing electrorefiner salt

    SciTech Connect

    Riley, Brian J.; Lepry, William C.; Crum, Jarrod V.

    2016-01-01

    Chlorosodalite has the general form of Na8(AlSiO4)6Cl2 and this paper describes experiments conducted to synthesize sodalite to immobilize a mixed chloride salt using solution-based techniques. Sodalites were made using different Group IV contributions from either Si(OC2H5)4 or Ge(OC2H5)4, NaAlO2, and a simulated spent electrorefiner salt solution containing a mixture of alkali, alkaline earth, and lanthanide chlorides. Additionally, 6 glass binders at low loadings of 5 mass% were evaluated as sintering aids for the consolidation process. The approach of using the organic Group IV additives can be used to produce large quantities of sodalite at room temperature and shows promise over a method where colloidal silica is used as the silica source. However, the small particle sizes inhibited densification during pressure-less sintering.

  17. Grapevine and Arabidopsis Cation-Chloride Cotransporters Localize to the Golgi and Trans-Golgi Network and Indirectly Influence Long-Distance Ion Transport and Plant Salt Tolerance1[OPEN

    PubMed Central

    Henderson, Sam W.; Wege, Stefanie; Qiu, Jiaen; Blackmore, Deidre H.; Walker, Amanda R.; Tyerman, Stephen D.; Walker, Rob R.; Gilliham, Matthew

    2015-01-01

    Plant cation-chloride cotransporters (CCCs) have been implicated in conferring salt tolerance. They are predicted to improve shoot salt exclusion by directly catalyzing the retrieval of sodium (Na+) and chloride (Cl−) ions from the root xylem. We investigated whether grapevine (Vitis vinifera [Vvi]) CCC has a role in salt tolerance by cloning and functionally characterizing the gene from the cultivar Cabernet Sauvignon. Amino acid sequence analysis revealed that VviCCC shares a high degree of similarity with other plant CCCs. A VviCCC-yellow fluorescent protein translational fusion protein localized to the Golgi and the trans-Golgi network and not the plasma membrane when expressed transiently in tobacco (Nicotiana benthamiana) leaves and Arabidopsis (Arabidopsis thaliana) mesophyll protoplasts. AtCCC-green fluorescent protein from Arabidopsis also localized to the Golgi and the trans-Golgi network. In Xenopus laevis oocytes, VviCCC targeted to the plasma membrane, where it catalyzed bumetanide-sensitive 36Cl–, 22Na+, and 86Rb+ uptake, suggesting that VviCCC (like AtCCC) belongs to the Na+-K+-2Cl– cotransporter class of CCCs. Expression of VviCCC in an Arabidopsis ccc knockout mutant abolished the mutant’s stunted growth phenotypes and reduced shoot Cl– and Na+ content to wild-type levels after growing plants in 50 mm NaCl. In grapevine roots, VviCCC transcript abundance was not regulated by Cl– treatment and was present at similar levels in both the root stele and cortex of three Vitis spp. genotypes that exhibit differential shoot salt exclusion. Our findings indicate that CCC function is conserved between grapevine and Arabidopsis, but neither protein is likely to directly mediate ion transfer with the xylem or have a direct role in salt tolerance. PMID:26378102

  18. Comparative avoidance behaviour of the earthworm Eisenia fetida towards chloride, nitrate and sulphate salts of Cd, Cu and Zn using filter paper and extruded water agar gels as exposure media.

    PubMed

    Demuynck, Sylvain; Lebel, Aurélie; Grumiaux, Fabien; Pernin, Céline; Leprêtre, Alain; Lemière, Sébastien

    2016-07-01

    We studied the avoidance behaviour of the earthworm Eisenia fetida towards Cd, Cu, and Zn, trace elements (TEs) tested as chloride, nitrate and sulphate salts. Sub adults were exposed individually using dual-cell chambers at 20+2°C in the dark. Recordings were realised at different dates from 2h to 32h. We used filter paper and extruded water agar gel as exposure media to evaluate the contribution of the dermal and the digestive exposure routes on the avoidance reactions. Exposures to Cu or Cd (10mgmetal ionL(-1)) resulted in highly significant avoidance reactions through the exposure duration. Worms avoided Zn poorly and reactions towards Zn salts varied along the exposure. Worm sensitivity towards TEs differed between salts and this could result from differential toxicity or accessibility of these TE salts to earthworms. The anion in itself was not the determinant of the avoidance reactions since exposures to similar concentrations of these anions using calcium salts did not result in significant avoidance worm behaviour. Avoidance responses towards TEs were higher in the case of water agar exposures than in filter paper exposures. Thus, dermal contacts with TE solutions would elicit worm avoidance but signals from receptors located inside the digestive tract could reinforce this behaviour. The use of extruded water agar gels as the substrate allows checking the real sensitivity of earthworm species towards TEs since the TE concentrations leading to significant avoidance reactions were below those reported in the literature when using TE-spiked soils.

  19. A reactor system for studying the interactions between alkali vapors and ceramic compounds

    SciTech Connect

    Shadman, F.; Punjak, W.A.

    1987-01-01

    The kinetics and mechanism of interaction between alkali vapors and several ceramic compounds are studied. A unique micro-gravimetric reactor is designed and utilized for this study. Bauxite and kaolin are very good adsorbents for alkali chlorides and are potentially good additives for control of alkali during coal combustion and gasification. The experimental data shows that the alkali capturing process is a combination of physisorption, chemisorption and chemical reaction. An analytical model is developed assuming a multi-layer adsorption of alkali on substrate followed by a rate-controlling rection on the surface. The experimental results and model predictions are in good agreement.

  20. Influence of the anions on the N-cationic benzethonium salts in the solid state and solution: Chloride, bromide, hydroxide and citrate hydrates

    NASA Astrophysics Data System (ADS)

    Paradies, Henrich H.; Reichelt, Hendrik

    2016-06-01

    The crystal structures of the hydrated cationic surfactant benzethonium (Bzth) chloride, bromide, hydroxide, and citrate have been determined by X-ray diffraction analysis and compared with their structures in solution well above their critical micelle concentration. The differences in the nature of the various anions of the four Bzth-X materials lead to unique anion environments and 3-D molecular arrangements. The water molecule in the monoclinic Bzth-Cl or Bzth-Br forms is hydrogen bonded to the halides and particularly to the hydrogens of the methoxy groups of the Bzth moiety notwithstanding the weak Brønsted acidity of the methoxy hydrogens. The citrate strongly interacts with the hydrogens of the methoxy group forming an embedded anionic spherical cluster of a radius of 2.6 Å. The Bzth-OH crystallizes in a hexagonal lattice with two water molecules and reveals free water molecules forming hydrogen bonded channels through the Bzth-OH crystal along the c-axis. The distances between the cationic nitrogen and the halides are 4.04 Å and 4.20 Å, significantly longer than expected for typical van der Waals distances of 3.30 Å. The structures show weakly interacting, alternating apolar and polar layers, which run parallel to the crystallographic a-b planes or a-c planes. The Bzth-X salts were also examined in aqueous solution containing 20% (v/v) ethanol and 1.0 % (v/v) glycerol well above their critical micelle concentration by small-angle X-ray scattering (SAXS) and wide-angle X-ray scattering (WAXS). The [1,1,1] planes for the Bzth Cl or Br, the [0,0,2] and [1,1,0] planes for the Bzth-citrate, the [2,-1,0] planes and the [0,0,1] planes for the Bzth-OH found in the crystalline phase were also present in the solution phase, accordingly, the preservation of these phases are a strong indication of periodicity in the solution phase.

  1. An Improved Analytical Method for Atmospheric Chlorides in Tropic Tests

    DTIC Science & Technology

    1975-07-01

    Chloride Electrode Chloride Analysis Methodology Tropic Regions Diphenylcarbazone- Panama Canal Zone Tropic Test Center Bromphenol Blue Salt Wet Candle 20...ambient salt has been measured for corrosion studies by wet- candle sampling and determining water-soluble chlorides by manual mercuric nitrate titration...of total chloride in wet- candle samplers. For the past 8 years atmospheric salt has been measured at tropic test sites by the wet- candle method

  2. Immobilization of fission products arising from pyrometallurgical reprocessing in chloride media

    NASA Astrophysics Data System (ADS)

    Leturcq, G.; Grandjean, A.; Rigaud, D.; Perouty, P.; Charlot, M.

    2005-12-01

    Spent nuclear fuel reprocessing to recover energy-producing elements such as uranium or plutonium can be performed by a pyrochemical process. In such method, the actinides and fission products are extracted by electrodeposition in a molten chloride medium. These processes generate chlorinated alkali salt flows contaminated by fission products, mainly Cs, Ba, Sr and rare earth elements constituting high-level waste. Two possible alternatives are investigated for managing this wasteform; a protocol is described for dechlorinating the fission products to allow vitrification, and mineral phases capable of immobilizing chlorides are listed to allow specification of a dedicated ceramic matrix suitable for containment of these chlorinated waste streams. The results of tests to synthesize chlorosilicate phases are also discussed.

  3. Disposition of salt-waste from pyrochemical nuclear fuel processing

    SciTech Connect

    Vance, E.R.

    2007-07-01

    Waste salts from pyrochemical processing of nuclear fuel can be immobilised in sodalite if consolidated by hot isostatic pressing (HIP) at {approx}750 deg. C/100 MPa in thick stainless steel 316 cans. Other canning materials for this purpose also look possible. Spodiosite-based waste forms do not look promising in terms of leach resistance and their incorporation of alkali ions and compatibility with other phases which could potentially accommodate fission products, such as NaZr{sub 2}(PO{sub 4}){sub 3} or alumino-phosphate glass. Chloro- or fluor-apatite-based waste forms however have been reported to successfully accommodate fission products and alkalis which would be derived from either chloride- or fluoride-based waste pyro-processing salts. The presence of 10 or 20 wt% of additional Whitlockite, Ca{sub 3}(PO{sub 4}){sub 2}, should allow chemical flexibility to maintain the same qualitative phase assemblage when there are variations in the waste feed and in the waste/precursor ratios. Experimental verification of incorporation of the full complement of waste salts and fission products is not yet complete however. Apatite-rich samples could likely be HIPed in Inconel 600 cans. Other candidate HIP canning materials such as Alloy 22 or Inconel 625 are under study by encapsulating them in the candidate waste form and studying their interaction or otherwise with the waste form. (author)

  4. Enhancement by sodium chloride of the selectivity of thiosulfate citrate bile salts sucrose agar for isolating Vibrio cholerae biotype El Tor.

    PubMed Central

    Morris, G K; DeWitt, W E; Gangarosa, E J; McCormack, W M

    1976-01-01

    In this study we utilized the salt-tolerant characteristics of vibrios to develop a more selective medium by addition of NaCl to thiosulfate citrate bile salts sucrose (TCBS) agar. The effect of adding salt to TCBS agar varied greatly among brands of TCBS agar and between lots of the same brand. The addition of salt at concentrations as high as 1.5% (2.5% total NaCl) caused the inhibition of growth of three species of commonly encountered normal bowel flora and one strain of classical Vibrio cholerae but did not compromise the use of TCBS agar for isolation of V. cholerae biotype El Tor. PMID:965476

  5. Speciation of phytate ion in aqueous solution. Alkali metal complex formation in different ionic media.

    PubMed

    De Stefano, Concetta; Milea, Demetrio; Pettignano, Alberto; Sammartano, Silvio

    2003-08-01

    The acid-base properties of phytic acid [ myo-inositol 1,2,3,4,5,6-hexakis(dihydrogen phosphate)] (H(12)Phy; Phy(12-)=phytate anion) were studied in aqueous solution by potentiometric measurements ([H+]-glass electrode) in lithium and potassium chloride aqueous media at different ionic strengths (0< I mol L(-1)< or =3) and at t=25 degrees C. The protonation of phytate proved strongly dependent on both ionic medium and ionic strength. The protonation constants obtained in alkali metal chlorides are considerably lower than the corresponding ones obtained in a previous paper in tetraethylammonium iodide (Et(4)NI; e.g., at I=0.5 mol L(-1), log K(3)(H)=11.7, 8.0, 9.1, and 9.1 in Et(4)NI, LiCl, NaCl and KCl, respectively; the protonation constants in Et(4)NI and NaCl were already reported), owing to the strong interactions occurring between the phytate and alkaline cations present in the background salt. We explained this in terms of complex formation between phytate and alkali metal ions. Experimental evidence allows us to consider the formation of 13 mixed proton-metal-ligand complexes, M(j)H(i)Phy((12-i-j)-), (M+ =Li+, Na+, K+), with j< or =7 and i< or =6, in the range 2.5< or =pH< or =10 (some measurements, at low ionic strength, were extended to pH=11). In particular, all the species formed are negatively charged: i+j-12=-5, -6. Very high formation percentages of M+-phytate species are observed in all the pH ranges investigated. The stability of alkali metal complexes follows the trend Li+ > or =Na+K+. Some measurements were also performed at constant ionic strength (I=0.5 mol L(-1)), using different mixtures of Et(4)NI and alkali metal chlorides, in order to confirm the formation of hypothesized and calculated metal-proton-ligand complex species and to obtain conditional protonation constants in these multi-component ionic media.

  6. The SALT NORM : a quantitative chemical-mineralogical characterization of natural waters

    USGS Publications Warehouse

    Bodine, Marc W.; Jones, Blair F.

    1986-01-01

    The new computer program SNORM calculates the salt norm from the chemical composition of a natural water. The salt norm is the quantitative ideal equilibrium assemblage that would crystallize if the water evaporated to dryness at 25 C and 1 bar pressure under atmospheric partial pressure of CO2. SNORM proportions solute concentrations to achieve charge balance. It quantitatively distributes the 18 acceptable solutes into normative salts that are assigned from 63 possible normative salts to allow only stable associations based on the Gibbs Phase Rule, available free energy values, and observed low-temperature mineral associations. Although most natural water compositions represent multiple solute origins, results from SNORM identify three major categories: meteoric or weathering waters that are characterized by normative alkali-bearing sulfate and carbonate salts: connate marine-like waters that are chloride-rich with a halite-bischofite-carnallite-kieserite-anhydrite association; and diagenetic waters that are frequently of marine origin but yield normative salts, such as Ca-bearing chlorides (antarcticite and tachyhydrite) and sylvite, which suggest solute alteration by secondary mineral reactions. The solute source or reaction process within each of the above categories is commonly indicated by the presence or absence of diagnostic normative salts and their relative abundance in the normative salt assemblage. For example, salt norms: (1) may identify lithologic source; (2) may identify the relative roles of carbonic and sulfuric acid hydrolysis in the evolution of weathering waters; (3) may identify the origin of connate water from normal marine, hypersaline, or evaporite salt resolution processes; and (4) may distinguish between dolomitization and silicate hydrolysis or exchange for the origin of diagenetic waters. (Author 's abstract)

  7. Chloride channels as drug targets

    PubMed Central

    Verkman, Alan S.; Galietta, Luis J. V.

    2013-01-01

    Chloride channels represent a relatively under-explored target class for drug discovery as elucidation of their identity and physiological roles has lagged behind that of many other drug targets. Chloride channels are involved in a wide range of biological functions, including epithelial fluid secretion, cell-volume regulation, neuroexcitation, smooth-muscle contraction and acidification of intracellular organelles. Mutations in several chloride channels cause human diseases, including cystic fibrosis, macular degeneration, myotonia, kidney stones, renal salt wasting and hyperekplexia. Chloride-channel modulators have potential applications in the treatment of some of these disorders, as well as in secretory diarrhoeas, polycystic kidney disease, osteoporosis and hypertension. Modulators of GABAA (γ-aminobutyric acid A) receptor chloride channels are in clinical use and several small-molecule chloride-channel modulators are in preclinical development and clinical trials. Here, we discuss the broad opportunities that remain in chloride-channel-based drug discovery. PMID:19153558

  8. Permeable Asphalt: A New Tool to Reduce Road Salt Contamination of Groundwater in Urban Areas.

    PubMed

    Dietz, Michael E; Angel, Derek R; Robbins, Gary A; McNaboe, Lukas A

    2017-03-01

    Chloride contamination of groundwater in urban areas due to deicing is a well-documented phenomenon in northern climates. The objective of this study was to evaluate the effects of permeable pavement on degraded urban groundwater. Although low impact development practices have been shown to improve stormwater quality, no infiltration practice has been found to prevent road salt chlorides from entering groundwater. The few studies that have investigated chlorides in permeable asphalt have involved sampling directly beneath the asphalt; no research has looked more broadly at surrounding groundwater conditions. Monitoring wells were installed upgradient and downgradient of an 860 m(2) permeable asphalt parking lot at the University of Connecticut (Storrs, Connecticut). Water level and specific conductance were measured continuously, and biweekly samples were analyzed for chloride. Samples were also analyzed for sodium (Na), calcium (Ca), and magnesium (Mg). Analysis of variance analysis indicated a significantly (p < 0.001) lower geometric mean Cl concentration downgradient (303.7 mg/L) as compared to upgradient (1280 mg/L). Concentrations of all alkali metals increased upgradient and downgradient during the winter months as compared to nonwinter months, indicating that cation exchange likely occurred. Despite the frequent high peaks of chloride in the winter months as well as the increases in alkali metals observed, monitoring revealed lower Cl concentrations downgradient than upgradient for the majority of the year. These results suggest that the use of permeable asphalt in impacted urban environments with high ambient chloride concentrations can be beneficial to shallow groundwater quality, although these results may not be generalizable to areas with low ambient chloride concentrations.

  9. Electrochemical cell having an alkali-metal-nitrate electrode

    DOEpatents

    Roche, M.F.; Preto, S.K.

    1982-06-04

    A power-producing secondary electrochemical cell includes a molten alkali metal as the negative-electrode material and a molten-nitrate salt as the positive-electrode material. The molten material in the respective electrodes are separated by a solid barrier of alkali-metal-ion conducting material. A typical cell includes active materials of molten sodium separated from molten sodium nitrate and other nitrates in mixture by a layer of sodium ..beta..'' alumina.

  10. Sodium: How to Tame Your Salt Habit

    MedlinePlus

    ... same amount of sodium as table salt. Use salt substitutes wisely. Some salt substitutes or light salts contain a mixture of table ... substitute — and get too much sodium. Also, many salt substitutes contain potassium chloride. Although potassium can lessen some ...

  11. Chloride-inducible transient apoplastic alkalinizations induce stomata closure by controlling abscisic acid distribution between leaf apoplast and guard cells in salt-stressed Vicia faba.

    PubMed

    Geilfus, Christoph-Martin; Mithöfer, Axel; Ludwig-Müller, Jutta; Zörb, Christian; Muehling, Karl H

    2015-11-01

    Chloride stress causes the leaf apoplast transiently to alkalize, an event that is presumed to contribute to the ability of plants to adapt to saline conditions. However, the initiation of coordinated processes downstream of the alkalinization is unknown. We hypothesize that chloride-inducible pH dynamics are a key chemical feature modulating the compartmental distribution of abscisic acid (ABA) and, as a consequence, affecting stomata aperture. Apoplastic pH and stomata aperture dynamics in intact Vicia faba leaves were monitored by microscopy-based ratio imaging and porometric measurements of stomatal conductance. ABA concentrations in leaf apoplast and guard cells were compared with pH dynamics by gas-chromatography-mass-spectrometry (GC-MS) and liquid-chromatography-tandem-mass spectrometry (LC-MS/MS). Results demonstrate that, upon chloride addition to roots, an alkalizing factor that initiates the pH dynamic propagates from root to leaf in a way similar to xylem-distributed water. In leaves, it induces a systemic transient apoplastic alkalinization that causes apoplastic ABA concentration to increase, followed by an elevation of endogenous guard cell ABA. We conclude that the transient alkalinization, which is a remote effect of chloride stress, modulates the compartmental distribution of ABA between the leaf apoplast and the guard cells and, in this way, is instrumental in inducing stomata closure during the beginning of salinity.

  12. Dual alkali approaches for the capture and separation of CO{sub 2}

    SciTech Connect

    Huang, H.P.; Shi, Y.; Li, W.; Chang, S.G.

    2000-04-04

    The Solvay process utilizes two alkalis in sequential order to convert CO{sub 2} to sodium carbonate for commercial use. The ability to transform CO{sub 2} into sodium carbonate cost-effectively would be a breakthrough in CO{sub 2} sequestration by providing benign long-term storage of CO{sub 2}. However, the Solvay process was not designed for CO{sub 2} sequestration and is not practical for use in the sequestration of CO{sub 2} from fossil fuel power plants. This paper investigates methods to modify the process in order to make it effective for the control of power plant CO{sub 2} emissions. The new modified process, called the Dual Alkali Approach, attempts to replace either or both bases, ammonia and lime, in the Solvay process with other compounds to make CO{sub 2} capture and separation efficient. Ammonia was replaced with different amines in aqueous solutions of salts and it was found that bicarbonate precipitation did occur. A method to regenerate the amine in the second step has not been implemented. However, the second step in Solvay Process has been implemented without using lime, namely, ammonia has been regenerated from an ammonium chloride solution using activated carbon. The HCl adsorbed in the activated carbon was removed by water to regenerate the activated carbon.

  13. Plutonium and americium separation from salts

    DOEpatents

    Hagan, Paul G.; Miner, Frend J.

    1976-01-01

    Salts or materials containing plutonium and americium are dissolved in hydrochloric acid, heated, and contacted with an alkali metal carbonate solution to precipitate plutonium and americium carbonates which are thereafter readily separable from the solution.

  14. Hydrogen-bonded and π-interaction assembly in two 8-alkoxycarbonyl-1,8-diazabicyclo[5.4.0]undec-7-enium chloride salts.

    PubMed

    Mesto, E; Quaranta, E

    2013-04-01

    The crystal structures of 8-phenoxycarbonyl-1,8-diazabicyclo[5.4.0]undec-7-enium chloride, C16H21N2O2(+)·Cl(-), (I), and 8-methoxycarbonyl-1,8-diazabicyclo[5.4.0]undec-7-enium chloride monohydrate, C11H19N2O2(+)·Cl(-)·H2O, (II), recently reported by Carafa, Mesto & Quaranta [Eur. J. Org. Chem. (2011), pp. 2458-2465], are analysed and discussed with a focus on crystal interaction assembly. Both compounds crystallize in the space group P2(1)/c. The crystal packings are characterized by dimers linked through π-π stacking interactions and intermolecular nonclassical hydrogen bonds, respectively. Additional intermolecular C-H···Cl interactions [in (I) and (II)] and classical O-H···Cl hydrogen bonds [in (II)] are also evident and contribute to generating three-dimensional hydrogen-bonded networks.

  15. Technical and economic feasibility of salt-gradient solar ponds at the Truscott Brine Lake of the Red River Chloride Control Project. A report to the House-Senate Committee on Appropriations of the Ninety-Seventh Congress

    SciTech Connect

    Not Available

    1982-09-01

    The Truscott Brine Lake is being constructed to impound highly brackish water from a number of sources which would normally flow into the Wichita River, a tributary of the Red River in Knox County, Texas. A 35.4-km (22-mile) pipeline is being constructed to carry the brines from their primary source to the Truscott Brine Lake site. The reservoir is designed to contain 100 years of brine emissions from three chloride emission areas in the Wichita River Basin. The solar ponds and power generating facilities would be located in the Bluff Creek Arm of Truscott Brine Lake. The Truscott Brine Lake study includes: survey of suitability of Truscott Lake site, review of solar pond technology, preconceptual design of solar salt pond power plant, and economic evaluation.

  16. Synthesis of cationic flocculant by radiation-induced copolymerization of methyl chloride salt of N,N-dimethylaminoethyl methacrylate with acrylamide in aqueous solution. II. Copolymerization at higher monomer concentration

    SciTech Connect

    Ishigaki, I.; Fukuzaki, H.; Okada, T.; Okada, T.; Okamoto, J.; Machi, S.

    1981-05-01

    The radiation-induced copolymerization of methyl chloride salt of N,N-dimethylaminoethyl methacrylate with acrylamide was studied to prepare a polymer flocculant that can be handled as a solid. The product obtained in the presence of 5 to 20% water was a solid and could be ground to a powder without drying. In order to obtain a water-soluble polymer at a higher concentration, the effect of various additives on the copolymerization was investigated and found that alcohols bearing a hydrogen atom attached to the tertiary carbon atom effectively inhibit intermolecular crosslinking to give water-soluble polymer. It is suggested that the formation of water-insoluble polymer is predominantly attributable to the crosslinking of polymer chains rather than to the imidation of amide groups. Copolymerization in the presence of isopropyl alcohol as inhibitor of the crosslinking was also studied and compared with that reported previously, which was carried out at a lower monomer concentration without additives.

  17. Alkali metal ionization detector

    DOEpatents

    Bauerle, James E.; Reed, William H.; Berkey, Edgar

    1978-01-01

    Variations in the conventional filament and collector electrodes of an alkali metal ionization detector, including the substitution of helical electrode configurations for either the conventional wire filament or flat plate collector; or, the substitution of a plurality of discrete filament electrodes providing an in situ capability for transferring from an operationally defective filament electrode to a previously unused filament electrode without removing the alkali metal ionization detector from the monitored environment. In particular, the helical collector arrangement which is coaxially disposed about the filament electrode, i.e. the thermal ionizer, provides an improved collection of positive ions developed by the filament electrode. The helical filament design, on the other hand, provides the advantage of an increased surface area for ionization of alkali metal-bearing species in a monitored gas environment as well as providing a relatively strong electric field for collecting the ions at the collector electrode about which the helical filament electrode is coaxially positioned. Alternatively, both the filament and collector electrodes can be helical. Furthermore, the operation of the conventional alkali metal ionization detector as a leak detector can be simplified as to cost and complexity, by operating the detector at a reduced collector potential while maintaining the sensitivity of the alkali metal ionization detector adequate for the relatively low concentration of alkali vapor and aerosol typically encountered in leak detection applications.

  18. Chlorine Salts at the Phoenix Landing Site

    NASA Astrophysics Data System (ADS)

    Hanley, J.; Horgan, B.

    2016-09-01

    Although chlorine salts (perchlorates, chlorides) are known to exist at the Phoenix landing site, their distribution and type have not been positively identified yet. We look for these salts through a novel NIR remote sensing technique.

  19. EXCESS FREE ENERGIES OF BINARY MOLTEN SALT MIXTURES FROM EMF DATA.

    DTIC Science & Technology

    SALTS , *FREE ENERGY), (*HALIDES, FREE ENERGY), ELECTRICAL PROPERTIES, THERMOCHEMISTRY, SILVER COMPOUNDS, LEAD COMPOUNDS, POTASSIUM COMPOUNDS...CERIUM COMPOUNDS, CALCIUM COMPOUNDS, MAGNESIUM COMPOUNDS, SODIUM CHLORIDE, CHLORIDES, BROMIDES, IODIDES

  20. Chloride salt type/ionic strength and refrigeration effects on antioxidant enzymes and lipid oxidation in cattle, camel and chicken meat.

    PubMed

    Gheisari, Hamid Reza; Motamedi, Hossien

    2010-10-01

    The effects of NaCl and KCl at varying ionic strengths on catalase and glutathione peroxidase (GSH-Px) activities and lipid oxidation in ground Longissimus dorsi (LD) of cattle and camel and breast muscle of chicken during refrigerated storage were studied. NaCl and KCl significantly increased 2-thiobarbituric reactive substances (TBARS) and peroxide values. TBARS and peroxide values increased and GSH-Px activity decreased during 4 day storage in the 4 degrees C, but catalase activity was stable. Salt type had no consistent effect on GSH-Px and catalase activities. Chicken samples had lower enzyme activities and TBARS content than cattle and camel. Their peroxide values were lower than camel samples. Camel meat showed higher catalase activity and TBARS content than cattle meat. Results indicated that negative correlation between lipid oxidation and GSH-Px activity and the accelerated lipid oxidation in salted meat may be partly related to a decrease in GSH-Px activity.

  1. Apparatus enables accurate determination of alkali oxides in alkali metals

    NASA Technical Reports Server (NTRS)

    Dupraw, W. A.; Gahn, R. F.; Graab, J. W.; Maple, W. E.; Rosenblum, L.

    1966-01-01

    Evacuated apparatus determines the alkali oxide content of an alkali metal by separating the metal from the oxide by amalgamation with mercury. The apparatus prevents oxygen and moisture from inadvertently entering the system during the sampling and analytical procedure.

  2. Solution-derived sodalite made with Si- and Ge-ethoxide precursors for immobilizing electrorefiner salt

    NASA Astrophysics Data System (ADS)

    Riley, Brian J.; Lepry, William C.; Crum, Jarrod V.

    2016-01-01

    Chlorosodalite has the general form of Na8(AlSiO4)6Cl2 and this paper describes experiments conducted to synthesize sodalite with a solution-based approach to immobilize a simulated spent electrorefiner salt solution containing a mixture of alkali, alkaline earth, and lanthanide chlorides. The reactants used were the salt solution, NaAlO2, and either Si(OC2H5)4 or Ge(OC2H5)4. Additionally, seven different glass sintering aids (at loadings of 5 mass%) were evaluated as sintering aids for consolidating the as-made powders using a cold-press-and-sinter technique. This process of using alkoxide additives for the Group IV component can be used to produce large quantities of sodalite at near-room temperature as compared to a method where colloidal silica was used as the silica source. However, the small particle sizes inhibited densification during heat treatments.

  3. An Overview of Liquid Fluoride Salt Heat Transport Systems

    SciTech Connect

    Holcomb, David Eugene; Cetiner, Sacit M

    2010-09-01

    Heat transport is central to all thermal-based forms of electricity generation. The ever increasing demand for higher thermal efficiency necessitates power generation cycles transitioning to progressively higher temperatures. Similarly, the desire to provide direct thermal coupling between heat sources and higher temperature chemical processes provides the underlying incentive to move toward higher temperature heat transfer loops. As the system temperature rises, the available materials and technology choices become progressively more limited. Superficially, fluoride salts at {approx}700 C resemble water at room temperature being optically transparent and having similar heat capacity, roughly three times the viscosity, and about twice the density. Fluoride salts are a leading candidate heat-transport material at high temperatures. Fluoride salts have been extensively used in specialized industrial processes for decades, yet they have not entered widespread deployment for general heat transport purposes. This report does not provide an exhaustive screening of potential heat transfer media and other high temperature liquids such as alkali metal carbonate eutectics or chloride salts may have economic or technological advantages. A particular advantage of fluoride salts is that the technology for their use is relatively mature as they were extensively studied during the 1940s-1970s as part of the U.S. Atomic Energy Commission's program to develop molten salt reactors (MSRs). However, the instrumentation, components, and practices for use of fluoride salts are not yet developed sufficiently for commercial implementation. This report provides an overview of the current understanding of the technologies involved in liquid salt heat transport (LSHT) along with providing references to the more detailed primary information resources. Much of the information presented here derives from the earlier MSR program. However, technology has evolved over the intervening years, and

  4. Ideas about Acids and Alkalis.

    ERIC Educational Resources Information Center

    Toplis, Rob

    1998-01-01

    Investigates students' ideas, conceptions, and misconceptions about acids and alkalis before and after a teaching sequence in a small-scale research project. Concludes that student understanding of acids and alkalis is lacking. (DDR)

  5. Methods of recovering alkali metals

    DOEpatents

    Krumhansl, James L; Rigali, Mark J

    2014-03-04

    Approaches for alkali metal extraction, sequestration and recovery are described. For example, a method of recovering alkali metals includes providing a CST or CST-like (e.g., small pore zeolite) material. The alkali metal species is scavenged from the liquid mixture by the CST or CST-like material. The alkali metal species is extracted from the CST or CST-like material.

  6. Synergistic capture mechanisms for alkali and sulphur species from combustion. Quarterly report No. 10, December 1992--February 1993

    SciTech Connect

    Peterson, T.W.; Shadman, F.; Wendt, J.O.L.; Wu, Baochun

    1993-07-26

    A number of sorbents with alumina-silicate base and sulfur capturing active sites have been developed for simultaneous removal of alkali metal compounds and sulfur dioxide. Current report will focus on bauxite sorbents, which includes experiments on sulfur dioxide absorption, alkali capturing and alkali/sulfur absorption simultaneously by bauxite-based sorbents. The alkali compound used here is sodium chloride. Experiments show an effective adsorption of sulfur or alkali separately, and the combined adsorption of alkali/sulfur. Atomic absorption analysis of reaction products shows that there is a much higher sodium content in the combined reaction products than that of the single reaction of alkali absorption by bauxite. Further X-ray diffraction analysis shows that there is sodium sulfate in the final products of simultaneous reaction, which indicates the formation and then condensation of sodium sulfate in the reaction system.

  7. On-chip fabrication of alkali-metal vapor cells utilizing an alkali-metal source tablet

    NASA Astrophysics Data System (ADS)

    Tsujimoto, K.; Ban, K.; Hirai, Y.; Sugano, K.; Tsuchiya, T.; Mizutani, N.; Tabata, O.

    2013-11-01

    We describe a novel on-chip microfabrication technique for the alkali-metal vapor cell of an optically pumped atomic magnetometer (OPAM), utilizing an alkali-metal source tablet (AMST). The newly proposed AMST is a millimeter-sized piece of porous alumina whose considerable surface area holds deposited alkali-metal chloride (KCl) and barium azide (BaN6), source materials that effectively produce alkali-metal vapor at less than 400 °C. Our experiments indicated that the most effective pore size of the AMST is between 60 and 170 µm. The thickness of an insulating glass spacer holding the AMST was designed to confine generated alkali metal to the interior of the vapor cell during its production, and an integrated silicon heater was designed to seal the device using a glass frit, melted at an optimum temperature range of 460-490 °C that was determined by finite element method thermal simulation. The proposed design and AMST were used to successfully fabricate a K cell that was then operated as an OPAM with a measured sensitivity of 50 pT. These results demonstrate that the proposed concept for on-chip microfabrication of alkali-metal vapor cells may lead to effective replacement of conventional glassworking approaches.

  8. Chloride Test

    MedlinePlus

    ... of the imbalance. In persons with too much base, urine chloride measurements can tell the healthcare practitioner whether the cause ... healthcare practitioner will look at whether the chloride measurement changes ... an acid-base imbalance and helps to guide treatment. ^ Back to ...

  9. Hydrothermal alkali metal recovery process

    DOEpatents

    Wolfs, Denise Y.; Clavenna, Le Roy R.; Eakman, James M.; Kalina, Theodore

    1980-01-01

    In a coal gasification operation or similar conversion process carried out in the presence of an alkali metal-containing catalyst wherein solid particles containing alkali metal residues are produced, alkali metal constituents are recovered from the particles by treating them with a calcium or magnesium-containing compound in the presence of water at a temperature between about 250.degree. F. and about 700.degree. F. and in the presence of an added base to establish a pH during the treatment step that is higher than would otherwise be possible without the addition of the base. During the treating process the relatively high pH facilitates the conversion of water-insoluble alkali metal compounds in the alkali metal residues into water-soluble alkali metal constituents. The resultant aqueous solution containing water-soluble alkali metal constituents is then separated from the residue solids, which consist of the treated particles and any insoluble materials formed during the treatment step, and recycled to the gasification process where the alkali metal constituents serve as at least a portion of the alkali metal constituents which comprise the alkali metal-containing catalyst. Preferably, the base that is added during the treatment step is an alkali metal hydroxide obtained by water washing the residue solids produced during the treatment step.

  10. Chemically induced fracturing in alkali feldspar

    NASA Astrophysics Data System (ADS)

    Scheidl, K. S.; Schaeffer, A.-K.; Petrishcheva, E.; Habler, G.; Fischer, F. D.; Schreuer, J.; Abart, R.

    2014-01-01

    Fracturing in alkali feldspar during Na+-K+ cation exchange with a NaCl-KCl salt melt was studied experimentally. Due to a marked composition dependence of the lattice parameters of alkali feldspar, any composition gradient arising from cation exchange causes coherency stress. If this stress exceeds a critical level fracturing occurs. Experiments were performed on potassium-rich gem-quality alkali feldspars with polished (010) and (001) surfaces. When the feldspar was shifted toward more sodium-rich compositions over more than about 10 mole %, a system of parallel cracks with regular crack spacing formed. The cracks have a general (h0l) orientation and do not correspond to any of the feldspar cleavages. The cracks are rather oriented (sub)-perpendicular to the direction of maximum tensile stress. The critical stress needed to initiate fracturing is about 325 MPa. The critical stress intensity factor for the propagation of mode I cracks, K Ic, is estimated as 2.30-2.72 MPa m1/2 (73-86 MPa mm1/2) from a systematic relation between characteristic crack spacing and coherency stress. An orientation mismatch of 18° between the crack normal and the direction of maximum tensile stress is ascribed to the anisotropy of the longitudinal elastic stiffness which has pronounced maxima in the crack plane and a minimum in the direction of the crack normal.

  11. Molten Metal Treatment by Salt Fluxing with Low Environmental Emissions

    SciTech Connect

    Yogeshwar Sahai

    2007-07-31

    Abstract: Chlorine gas is traditionally used for fluxing of aluminum melt for removal of alkali and alkaline earth elements. However this results in undesirable emissions of particulate matter and gases such as HCl and chlorine, which are often at unacceptable levels. Additionally, chlorine gas is highly toxic and its handling, storage, and use pose risks to employees and the local community. Holding of even minimal amounts of chlorine necessitates extensive training for all plant employees. Fugitive emissions from chlorine usage within the plant cause accelerated corrosion of plant equipment. The Secondary Aluminum Maximum Achievable Control Technology (MACT) under the Clean Air Act, finalized in March 2000 has set very tough new limits on particulate matter (PM) and total hydrogen chloride emissions from aluminum melting and holding furnaces. These limits are 0.4 and 0.1 lbs per ton of aluminum for hydrogen chloride and particulate emissions, respectively. Assuming new technologies for meeting these limits can be found, additional requirements under the Clean Air Act (Prevention of Significant Deterioration and New Source Review) trigger Best Available Control Technology (BACT) for new sources with annual emissions (net emissions not expressed per ton of production) over specified amounts. BACT currently is lime coated bag-houses for control of particulate and HCl emissions. These controls are expensive, difficult to operate and maintain, and result in reduced American competitiveness in the global economy. Solid salt fluxing is emerging as a viable option for the replacement of chlorine gas fluxing, provided emissions can be consistently maintained below the required levels. This project was a cooperative effort between the Ohio State University and Alcoa to investigate and optimize the effects of solid chloride flux addition in molten metal for alkali impurity and non-metallic inclusion removal minimizing dust and toxic emissions and maximizing energy

  12. The evaluation of the pyrochemistry for the treatment of Gen IV nuclear fuels Inert matrix chlorination studies in the gas phase or molten chloride salts

    NASA Astrophysics Data System (ADS)

    Bourg, S.; Péron, F.; Lacquement, J.

    2007-01-01

    The structure of the fuels for the future Gen IV nuclear reactors will be totally different from those of PWR, especially for the GFR concept including a closed cycle. In these reactors, fissile materials (carbides or nitrides of actinides) should be surrounded by an inert matrix. In order to build a reprocessing process scheme, the behavior of the potential inert matrices (silicon carbide, titanium nitride, and zirconium carbide and nitride) was studied by hydro- and pyrometallurgy. This paper deals with the chlorination results at high temperature by pyrometallurgy. For the first time, the reactivity of the matrix towards chlorine gas was assessed in the gas phase. TiN, ZrN and ZrC are very reactive from 400 °C whereas it is necessary to be over 900 °C for SiC to be as fast. In molten chloride melts, the bubbling of chlorine gas is less efficient than in gas phase but it is possible to attack the matrices. Electrochemical methods were also used to dissolve the refractory materials, leading to promising results with TiN, ZrN and ZrC. The massive SiC samples used were not conductive enough to be studied and in this case specific SiC-coated carbon electrodes were used. The key point of these studies was to find a method to separate the matrix compounds from the fissile material in order to link the head to the core of the process (electrochemical separation or liquid-liquid reductive extraction in the case of a pyrochemical reprocessing).

  13. High-temperature interactions of alkali vapors with solids during coal combustion and gasification

    SciTech Connect

    Punjak, W.A.

    1988-01-01

    A temperature and concentration programmed reaction method is used to investigate the mechanism by which organically bound alkali is released from carbonaceous substrates. Vaporization of the alkali is preceded by reduction of oxygen-bearing groups during which CO is generated. A residual amount of alkali remains after complete reduction. This residual level is greater for potassium, indicating that potassium has stronger interactions with graphitic substrates that sodium. Other mineral substrates were exposed to high temperature alkali chloride vapors under both nitrogen and simulated flue gas atmospheres to investigate their potential application as sorbents for the removal of alkali from coal conversion flue gases. The compounds containing alumina and silica are found to readily adsorb alkali vapors and the minerals kaolinite, bauxite and emathlite are identified as promising alkali sorbents. The fundamentals of alkali adsorption on kaolinite, bauxite and emathlite are compared and analyzed both experimentally and through theoretical modeling. The experiments were performed in a microgravimetric reactor system; the sorbents were characterized before and after alkali adsorption using scanning Auger microscopy, X-ray diffraction analysis, mercury porosimetry and atomic emission spectrophotometry. The results show that the process is not a simple physical condensation, but a complex combination of several diffusion steps and reactions.

  14. Low temperature oxidation using support molten salt catalysts

    DOEpatents

    Weimer, Alan W.; Czerpak, Peter J.; Hilbert, Patrick M.

    2003-05-20

    Molten salt reactions are performed by supporting the molten salt on a particulate support and forming a fluidized bed of the supported salt particles. The method is particularly suitable for combusting hydrocarbon fuels at reduced temperatures, so that the formation NO.sub.x species is reduced. When certain preferred salts are used, such as alkali metal carbonates, sulfur and halide species can be captured by the molten salt, thereby reducing SO.sub.x and HCl emissions.

  15. Alkalis in alternative biofuels

    SciTech Connect

    Miles, T.R.; Miles, T.R. Jr.; Bryers, R.W.; Baxter, L.L.; Jenkins, B.M.; Oden, L.L.

    1994-12-31

    The alkali content and behavior of inorganic material of annually produced biofuels severely limits their use for generating electrical power in conventional furnaces. A recent eighteen-month investigation of the chemistry and firing characteristics of 26 different biofuels has been conducted. Firing conditions were simulated in the laboratory for eleven biofuels. This paper describes some results from the investigation including fuel properties, deposits, deposition mechanisms, and implications for biomass boiler design, fuel sampling and characterizations. Urban wood fuel, agricultural residues, energy crops, and other potential alternate fuels are included in the study. Conventional methods for establishing fuel alkali content and determining ash sticky temperatures were deceptive. The crux of the problem was found to be the high concentration of potassium in biofuels and its reactions with other fuel constituents which lower the ``sticky temperature`` of the ash to the 650 C to 760 C (1,200 F-1,400 F).

  16. Atomic forces between noble gas atoms, alkali ions, and halogen ions for surface interactions

    NASA Technical Reports Server (NTRS)

    Wilson, J. W.; Outlaw, R. A.; Heinbockel, J. H.

    1988-01-01

    The components of the physical forces between noble gas atoms, alkali ions, and halogen ions are analyzed and a data base developed from analysis of the two-body potential data, the alkali-halide molecular data, and the noble gas crystal and salt crystal data. A satisfactory global fit to this molecular and crystal data is then reproduced by the model to within several percent. Surface potentials are evaluated for noble gas atoms on noble gas surfaces and salt crystal surfaces with surface tension neglected. Within this context, the noble gas surface potentials on noble gas and salt crystals are considered to be accurate to within several percent.

  17. Alkali-vapor lasers

    NASA Astrophysics Data System (ADS)

    Zweiback, J.; Komashko, A.; Krupke, W. F.

    2010-02-01

    We report on the results from several of our alkali laser systems. We show highly efficient performance from an alexandrite-pumped rubidium laser. Using a laser diode stack as a pump source, we demonstrate up to 145 W of average power from a CW system. We present a design for a transversely pumped demonstration system that will show all of the required laser physics for a high power system.

  18. The interrelation of hydraulic and electrical conductivities, streaming potential, and salt filtration during the flow of chloride brines through a smectite layer at elevated pressures

    NASA Astrophysics Data System (ADS)

    Demir, Ilham

    1988-03-01

    Solutions of NaCl and NaCl-CaCl 2 were forced through a clay plug made by compacting the 0.5-2.0 μm size fraction of Cheto montmorillonite. The initial concentration of NaCl solution was 1.10 molal ( m), and that of NaCl-CaCl 2 solution was 0.92 m in NaCl and 0.075 m in CaCl 2. The thickness of the clay plug was 0.5 cm. Two experiments were carried out, one with the NaCl solution and one with the NaCl-CaCl 2 solution. It took six to seven weeks to achieve constancy of effluent chemical composition and of streaming potential. Compaction pressure ( Pc) in these room temperature experiments was 34.5 MPa (5000 psi), differential hydraulic pressure across the clay was 13.8 MPa (2000 psi), and mean hydraulic pressure ( Pmh) was 15.9 MPa (2300 psi). These values of Pc and Pmh are approximate for a depth of 1525 m in sedimentary basins. Hydraulic flow rate, streaming potential, and brine chemical composition were measured periodically until steady state. Electrical conductance of the clay plug was measured in the beginning and at the end of each experimental run. The presence of Ca 2+ in the brine resulted in lower hydraulic conductivity and streaming potential but slightly higher electrical conductivity. The electroviscous effect was shown to cause a significant reduction in the flow rate. The experimental results conform to the predictions of nonequilibrium thermodynamics, for both Na-Cl and Na-Ca-Cl systems, under these simulated subsurface conditions. Salt filtration efficiencies of 48% were measured. In the Na-Ca-Cl system, Na + was preferentially transported through the clay relative to Ca 2+.

  19. Molecular modeling of the structure and dynamics of the interlayer and surface species of mixed-metal layered hydroxides: Chloride and water in hydrocalumite (Friedel's salt)

    SciTech Connect

    KALINICHEV,ANDREY G.; KIRKPATRICK,R. JAMES; CYGAN,RANDALL T

    2000-01-17

    The dynamical behavior of Cl{sup {minus}} and H{sub 2}O molecules in the interlayer and on the (001) surface of the Ca-aluminate hydrate hydrocalumite (Friedel's salt) over a range of temperatures from {minus}100 to 300 C is studied using the technique of isothermal-isobaric molecular dynamics computer simulations. This phase is currently the best available model compound for other, typically more disordered, mixed-metal layered hydroxides. The computed crystallographic parameters and density are in good agreement with available X-ray diffraction data and the force field developed for these simulations preserves the structure and density to within less than 2% of their measured values. In contrast to the highly ordered arrangement of the interlayer water molecules interpreted from the X-ray data, the simulations reveal significant dynamic disorder in water orientations. At all simulated temperatures, the interlayer water molecules undergo rapid librations (hindered hopping rotations) around an axis essentially perpendicular to the layers. This results in breaking and reformation of hydrogen bonds with the neighboring Cl{sup {minus}} anions and in a time-averaged nearly uniaxial symmetry at Cl{sup {minus}}, in good agreement with recent {sup 35}Cl NMR measurements. Power spectra of translational, vibrational, and vibrational motions of interlayer and surface Cl{sup {minus}} and H{sub 2}O were calculated as Fourier transforms of the atomic velocity autocorrelation functions and compared with the corresponding spectra and dynamics for a bulk aqueous solution. The ordered interlayer space has significant effects on the motions. Strong electrostatic attraction between interlayer water molecules and Ca atoms in the principal layer makes the Ca{hor_ellipsis}OH{sub 2} bond direction the preferred axis for interlayer water librations. The calculated diffusion coefficient of Cl{sup {minus}} as an outer-sphere surface complex is almost three times that of inner-sphere Cl

  20. On Barium Oxide Solubility in Barium-Containing Chloride Melts

    NASA Astrophysics Data System (ADS)

    Nikolaeva, Elena V.; Zakiryanova, Irina D.; Bovet, Andrey L.; Korzun, Iraida V.

    2016-08-01

    Oxide solubility in chloride melts depends on temperature and composition of molten solvent. The solubility of barium oxide in the solvents with barium chloride content is essentially higher than that in molten alkali chlorides. Spectral data demonstrate the existence of oxychloride ionic groupings in such melts. This work presents the results of the BaO solubility in two molten BaCl2-NaCl systems with different barium chloride content. The received data together with earlier published results revealed the main regularities of BaO solubility in molten BaO-BaCl2-MCl systems.

  1. Molten Salt Thermal Energy Storage Systems

    NASA Technical Reports Server (NTRS)

    Maru, H. C.; Dullea, J. F.; Kardas, A.; Paul, L.; Marianowski, L. G.; Ong, E.; Sampath, V.; Huang, V. M.; Wolak, J. C.

    1978-01-01

    The feasibility of storing thermal energy at temperatures of 450 C to 535 C in the form of latent heat of fusion was examined for over 30 inorganic salts and salt mixtures. Alkali carbonate mixtures were chosen as phase-change storage materials in this temperature range because of their relatively high storage capacity and thermal conductivity, moderate cost, low volumetric expansion upon melting, low corrosivity, and good chemical stability. Means of improving heat conduction through the solid salt were explored.

  2. Commercial scale cucumber fermentations brined with calcium chloride instead of sodium chloride

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Development of low salt cucumber fermentation processes present opportunities to reduce the amount of sodium chloride (NaCl) that reaches fresh water streams from industrial activities. The objective of this research was to translate cucumber fermentation brined with calcium chloride instead of NaCl...

  3. Fermentation of cucumbers brined with calcium chloride instead of sodium chloride

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Generation of waste water containing sodium chloride from cucumber fermentation tank yards could be eliminated if cucumbers were fermented in brines that did not contain this salt. To determine if this is feasible, cucumbers were fermented in brines that contained only calcium chloride to maintain f...

  4. Salt and nephrolithiasis.

    PubMed

    Ticinesi, Andrea; Nouvenne, Antonio; Maalouf, Naim M; Borghi, Loris; Meschi, Tiziana

    2016-01-01

    Dietary sodium chloride intake is nowadays globally known as one of the major threats for cardiovascular health. However, there is also important evidence that it may influence idiopathic calcium nephrolithiasis onset and recurrence. Higher salt intake has been associated with hypercalciuria and hypocitraturia, which are major risk factors for calcium stone formation. Dietary salt restriction can be an effective means for secondary prevention of nephrolithiasis as well. Thus in this paper, we review the complex relationship between salt and nephrolithiasis, pointing out the difference between dietary sodium and salt intake and the best methods to assess them, highlighting the main findings of epidemiologic, laboratory and intervention studies and focusing on open issues such as the role of dietary salt in secondary causes of nephrolithiasis.

  5. 7 CFR 58.328 - Salt.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Salt. 58.328 Section 58.328 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections....328 Salt. The salt shall be free-flowing, white refined sodium chloride and shall meet...

  6. 7 CFR 58.721 - Salt.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Salt. 58.721 Section 58.721 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections....721 Salt. Salt shall be free flowing, white refined sodium chloride and shall meet the requirements...

  7. 7 CFR 58.328 - Salt.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Salt. 58.328 Section 58.328 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections....328 Salt. The salt shall be free-flowing, white refined sodium chloride and shall meet...

  8. 7 CFR 58.437 - Salt.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Salt. 58.437 Section 58.437 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections....437 Salt. The salt shall be free-flowing, white refined sodium chloride and shall meet...

  9. 7 CFR 58.437 - Salt.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Salt. 58.437 Section 58.437 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections....437 Salt. The salt shall be free-flowing, white refined sodium chloride and shall meet...

  10. 7 CFR 58.721 - Salt.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Salt. 58.721 Section 58.721 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections....721 Salt. Salt shall be free flowing, white refined sodium chloride and shall meet the requirements...

  11. 7 CFR 58.328 - Salt.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 3 2013-01-01 2013-01-01 false Salt. 58.328 Section 58.328 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections....328 Salt. The salt shall be free-flowing, white refined sodium chloride and shall meet...

  12. 7 CFR 58.328 - Salt.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 3 2014-01-01 2014-01-01 false Salt. 58.328 Section 58.328 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections....328 Salt. The salt shall be free-flowing, white refined sodium chloride and shall meet...

  13. 7 CFR 58.437 - Salt.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 3 2014-01-01 2014-01-01 false Salt. 58.437 Section 58.437 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections....437 Salt. The salt shall be free-flowing, white refined sodium chloride and shall meet...

  14. 7 CFR 58.328 - Salt.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 3 2012-01-01 2012-01-01 false Salt. 58.328 Section 58.328 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections....328 Salt. The salt shall be free-flowing, white refined sodium chloride and shall meet...

  15. 7 CFR 58.437 - Salt.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 3 2013-01-01 2013-01-01 false Salt. 58.437 Section 58.437 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections....437 Salt. The salt shall be free-flowing, white refined sodium chloride and shall meet...

  16. 7 CFR 58.721 - Salt.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 3 2013-01-01 2013-01-01 false Salt. 58.721 Section 58.721 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections....721 Salt. Salt shall be free flowing, white refined sodium chloride and shall meet the requirements...

  17. 7 CFR 58.721 - Salt.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 3 2014-01-01 2014-01-01 false Salt. 58.721 Section 58.721 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections....721 Salt. Salt shall be free flowing, white refined sodium chloride and shall meet the requirements...

  18. 7 CFR 58.437 - Salt.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 3 2012-01-01 2012-01-01 false Salt. 58.437 Section 58.437 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections....437 Salt. The salt shall be free-flowing, white refined sodium chloride and shall meet...

  19. 7 CFR 58.721 - Salt.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 3 2012-01-01 2012-01-01 false Salt. 58.721 Section 58.721 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards, Inspections....721 Salt. Salt shall be free flowing, white refined sodium chloride and shall meet the requirements...

  20. A Thermodynamic Model for Predicting Mineral Reactivity in Supercritical Carbon Dioxide: I. Phase Behavior of Carbon Dioxide - Water - Chloride Salt Systems Across the H2O-Rich to the CO2-Rich Regions

    SciTech Connect

    Springer, Ronald D.; Wang, Zheming; Anderko, Andre; Wang, Peiming; Felmy, Andrew R.

    2012-09-05

    Phase equilibria in mixtures containing carbon dioxide, water, and chloride salts have been investigated using a combination of solubility measurements and thermodynamic modeling. The solubility of water in the CO2-rich phase of ternary mixtures of CO2, H2O and NaCl or CaCl2 was determined, using near infrared spectroscopy, at 90 atm and 40 to 100 °C. These measurements fill a gap in the experimental database for CO2 water salt systems, for which phase composition data have been available only for the H2O-rich phases. A thermodynamic model for CO2 water salt systems has been constructed on the basis of the previously developed Mixed-Solvent Electrolyte (MSE) framework, which is capable of modeling aqueous solutions over broad ranges of temperature and pressure, is valid to high electrolyte concentrations, treats mixed-phase systems (with both scCO2 and water present) and can predict the thermodynamic properties of dry and partially water-saturated supercritical CO2 over broad ranges of temperature and pressure. Within the MSE framework the standard-state properties are calculated from the Helgeson-Kirkham-Flowers equation of state whereas the excess Gibbs energy includes a long-range electrostatic interaction term expressed by a Pitzer-Debye-Hückel equation, a virial coefficient-type term for interactions between ions and a short-range term for interactions involving neutral molecules. The parameters of the MSE model have been evaluated using literature data for both the H2O-rich and CO2-rich phases in the CO2 - H2O binary and for the H2O-rich phase in the CO2 - H2O - NaCl / KCl / CaCl2 / MgCl2 ternary and multicompontent systems. The model accurately represents the properties of these systems at temperatures from 0°C to 300 °C and pressures up to ~4000 atm. Further, the solubilities of H2O in CO2-rich phases that are predicted by the model are in agreement with the new measurements for the CO2 - H2O - NaCl and CO2 - H2O - CaCl2 systems. Thus, the model can be

  1. NUCLEAR MAGNETIC RELAXATION IN LIQUID METALS, ALLOYS, AND SALTS.

    DTIC Science & Technology

    NUCLEAR MAGNETIC RESONANCE, *ALKALI METAL ALLOYS, *LIQUID METALS, * SALTS , NUCLEAR MAGNETIC RESONANCE, NUCLEAR MAGNETIC RESONANCE, RELAXATION TIME... SODIUM , GALLIUM, SODIUM ALLOYS, THALLIUM, THALLIUM COMPOUNDS, MELTING, NUCLEAR SPINS, QUANTUM THEORY, OPERATORS(MATHEMATICS), BIBLIOGRAPHIES, INTEGRAL EQUATIONS, TEST EQUIPMENT, MATHEMATICAL ANALYSIS.

  2. Experimental determination of the solubility constant for magnesium chloride hydroxide hydrate (Mg 3Cl(OH) 5·4H 2O, phase 5) at room temperature, and its importance to nuclear waste isolation in geological repositories in salt formations

    NASA Astrophysics Data System (ADS)

    Xiong, Yongliang; Deng, Haoran; Nemer, Martin; Johnsen, Shelly

    2010-08-01

    In this study, the solubility constant of magnesium chloride hydroxide hydrate, Mg 3Cl(OH) 5·4H 2O, termed as phase 5, is determined from a series of solubility experiments in MgCl 2-NaCl solutions. The solubility constant in logarithmic units at 25 °C for the following reaction, MgCl(OH)·4HO+5H=3Mg+9HO(l)+Cl is calculated as 43.21 ± 0.33 (2 σ) based on the specific interaction theory (SIT) model for extrapolation to infinite dilution. The Gibbs free energy and enthalpy of formation for phase 5 at 25 °C are derived as -3384 ± 2 (2 σ) kJ mol -1 and -3896 ± 6 (2 σ) kJ mol -1, respectively. MgO (bulk, pure MgO corresponding to the mineral periclase) is the only engineered barrier certified by the Environmental Protection Agency (EPA) for emplacement in the Waste Isolation Pilot Plant (WIPP) in the US, and an Mg(OH) 2-based engineered barrier (bulk, pure Mg(OH) 2 corresponding to brucite) is to be employed in the Asse repository in Germany. Phase 5, and its similar phase, phase 3 (Mg 2Cl(OH) 3·4H 2O), could have a significant role in influencing the geochemical conditions in geological repositories for nuclear waste in salt formations where MgO or brucite is employed as engineered barriers. Based on our solubility constant for phase 5 in combination with the literature value for phase 3, we predict that the composition for the invariant point of phase 5 and phase 3 would be mMg = 1.70 and pmH = 8.94 in the Mg-Cl binary system. The recent WIPP Compliance Recertification Application Performance Assessment Baseline Calculations indicate that phase 5, instead of phase 3, is indeed a stable phase when the WIPP Generic Weep Brine (GWB), a Na-Mg-Cl-dominated brine associated with the Salado Formation, equilibrates with actinide-source-term phases, brucite, magnesium carbonates, halite and anhydrite. Therefore, phase 5 is important to the WIPP, and potentially important to other repositories in salt formations.

  3. Electrolysis of dilute sodium chloride solution in a diaphragm cell

    SciTech Connect

    Kubasov, V.L.; Ivanter, I.A.; Druzhinin, E.A.; Vorob'eva, V.B.

    1986-02-10

    In some cases, as in the production of iodine and bromine, dilute solutions of sodium chloride remain unutilized. In view of the existence of large amounts of unutilized spent sodium chloride solutions and their harmful effect when discharged into the environment, it is desirable to develop a process for production of chlorine and alkali with high current efficiencies, satisfying industrial requirements, from dilute sodium chloride solutions. The authors have therefore studied electrolysis of solutions containing 160 and 180 kg/m/sup 3/ of sodium chloride, having pH of 11.0-11.5, close in composition to solutions from the Cheleken chemical factory. The chlorine and alkali current efficiencies and the compositions of the anolyte, catholyte, and anode gas were determined.

  4. Alkali-activated binders by use of industrial by-products

    SciTech Connect

    Buchwald, A.; Schulz, M

    2005-05-01

    Cement kiln dust (CKD) materials are used as alkaline accelerators for latent hydraulic substances and as alkali activators for different alumosilicate materials, including ground-granulated blast furnace slag, low-calcium fly ash and metakaolin. The dusts differ in their phase composition, especially in the amount of reactive phases and the kind and amount of alkali salts. The quantitative phase composition, pore solution composition and strength behavior of the activated blends is reported.

  5. Sulfur oxides control technology series: Flue-gas desulfurization. Dual alkali process. Summary report

    SciTech Connect

    Not Available

    1980-10-01

    The report describes a dual alkali (or double alkali) flue gas desulfurization (FGD), which is a throwaway process in which sulfur dioxide (SO2) is removed from the flue gas by a soluble sodium-based scrubbing liquor. The collected SO2 is precipitated as calcium sulfite (CaSO3), calcium sulfate (CaSO4), or a mixed crystal of both salts, and is purged from the system.

  6. Effect of cofiring coal and biofuel with sewage sludge on alkali problems in a circulating fluidized bed boiler

    SciTech Connect

    K.O. Davidsson; L.-E. Aamand; A.-L. Elled; B. Leckner

    2007-12-15

    Cofiring experiments were performed in a 12 MW circulating fluidized bed boiler. The fuel combinations were biofuel (wood+straw), coal+biofuel, coal+sewage sludge+biofuel, and sewage sludge+biofuel. Limestone or chlorine (PVC) was added in separate experiments. Effects of feed composition on bed ash and fly ash were examined. The composition of flue gas was measured, including on-line measurement of alkali chlorides. Deposits were collected on a probe simulating a superheater tube. It was found that the fuel combination, as well as addition of limestone, has little effect on the alkali fraction in bed ash, while chlorine decreases the alkali fraction in bed ash. Sewage sludge practically eliminates alkali chlorides in flue gas and deposits. Addition of enough limestone to coal and sludge for elimination of the SO{sub 2} emission does not change the effect of chlorine. Chlorine addition increases the alkali chloride in flue gas, but no chlorine was found in the deposits with sewage sludge as a cofuel. Cofiring of coal and biofuel lowers the alkali chloride concentration in the flue gas to about a third compared with that of pure biofuel. This is not affected by addition of lime or chlorine. It is concluded that aluminum compounds in coal and sludge are more important than sulfur to reduce the level of KCl in flue gas and deposits. 24 refs., 8 figs., 7 tabs.

  7. Method for synthesizing pollucite from chabazite and cesium chloride

    DOEpatents

    Pereira, Candido

    1999-01-01

    A method for immobilizing waste chlorides salts containing radionuclides and hazardous nuclear material for permanent disposal, and in particular, a method for immobilizing waste chloride salts containing cesium, in a synthetic form of pollucite. The method for synthesizing pollucite from chabazite and cesium chloride includes mixing dry, non-aqueous cesium chloride with chabazite and heating the mixture to a temperature greater than the melting temperature of the cesium chloride, or above about 700.degree. C. The method further comprises significantly improving the rate of retention of cesium in ceramic products comprised of a salt-loaded zeolite by adding about 10% chabazite by weight to the salt-loaded zeolite prior to conversion at elevated temperatures and pressures to the ceramic composite.

  8. Method for synthesizing pollucite from chabazite and cesium chloride

    DOEpatents

    Pereira, C.

    1999-02-23

    A method is described for immobilizing waste chlorides salts containing radionuclides and hazardous nuclear material for permanent disposal, and in particular, a method is described for immobilizing waste chloride salts containing cesium, in a synthetic form of pollucite. The method for synthesizing pollucite from chabazite and cesium chloride includes mixing dry, non-aqueous cesium chloride with chabazite and heating the mixture to a temperature greater than the melting temperature of the cesium chloride, or above about 700 C. The method further comprises significantly improving the rate of retention of cesium in ceramic products comprised of a salt-loaded zeolite by adding about 10% chabazite by weight to the salt-loaded zeolite prior to conversion at elevated temperatures and pressures to the ceramic composite. 3 figs.

  9. Preparation of alkali metal dispersions

    NASA Technical Reports Server (NTRS)

    Rembaum, A.; Landel, R. F. (Inventor)

    1968-01-01

    A method is described for producing alkali metal dispersions of high purity. The dispersions are prepared by varying the equilibrium solubility of the alkali metal in a suitable organic solvent in the presence of aromatic hydrocarbons. The equilibrium variation is produced by temperature change. The size of the particles is controlled by controlling the rate of temperature change.

  10. PROCESS OF RECOVERING ALKALI METALS

    DOEpatents

    Wolkoff, J.

    1961-08-15

    A process is described of recovering alkali metal vapor by sorption on activated alumina, activated carbon, dehydrated zeolite, activated magnesia, or Fuller's earth preheated above the vaporization temperature of the alkali metal and subsequent desorption by heating the solvent under vacuum. (AEC)

  11. Food composition and acid-base balance: alimentary alkali depletion and acid load in herbivores.

    PubMed

    Kiwull-Schöne, Heidrun; Kiwull, Peter; Manz, Friedrich; Kalhoff, Hermann

    2008-02-01

    Alkali-enriched diets are recommended for humans to diminish the net acid load of their usual diet. In contrast, herbivores have to deal with a high dietary alkali impact on acid-base balance. Here we explore the role of nutritional alkali in experimentally induced chronic metabolic acidosis. Data were collected from healthy male adult rabbits kept in metabolism cages to obtain 24-h urine and arterial blood samples. Randomized groups consumed rabbit diets ad libitum, providing sufficient energy but variable alkali load. One subgroup (n = 10) received high-alkali food and approximately 15 mEq/kg ammonium chloride (NH4Cl) with its drinking water for 5 d. Another group (n = 14) was fed low-alkali food for 5 d and given approximately 4 mEq/kg NH4Cl daily for the last 2 d. The wide range of alimentary acid-base load was significantly reflected by renal base excretion, but normal acid-base conditions were maintained in the arterial blood. In rabbits fed a high-alkali diet, the excreted alkaline urine (pH(u) > 8.0) typically contained a large amount of precipitated carbonate, whereas in rabbits fed a low-alkali diet, both pH(u) and precipitate decreased considerably. During high-alkali feeding, application of NH4Cl likewise decreased pH(u), but arterial pH was still maintained with no indication of metabolic acidosis. During low-alkali feeding, a comparably small amount of added NH4Cl further lowered pH(u) and was accompanied by a significant systemic metabolic acidosis. We conclude that exhausted renal base-saving function by dietary alkali depletion is a prerequisite for growing susceptibility to NH4Cl-induced chronic metabolic acidosis in the herbivore rabbit.

  12. Hydrogen chloride

    Integrated Risk Information System (IRIS)

    Hydrogen chloride ; CASRN 7647 - 01 - 0 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogeni

  13. Mepiquat chloride

    Integrated Risk Information System (IRIS)

    Mepiquat chloride ; CASRN 24307 - 26 - 4 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogen

  14. Acetyl chloride

    Integrated Risk Information System (IRIS)

    Acetyl chloride ; CASRN 75 - 36 - 5 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogenic Ef

  15. Methyl chloride

    Integrated Risk Information System (IRIS)

    EPA / 635 / R01 / 003 TOXICOLOGICAL REVIEW OF METHYL CHLORIDE ( CAS No . 74 - 87 - 3 ) In Support of Summary Information on the Integrated Risk Information System ( IRIS ) June 2001 U.S . Environmental Protection Agency Washington , DC DISCLAIMER This document has been reviewed in accordance with U.

  16. Vinyl chloride

    Integrated Risk Information System (IRIS)

    EPA / 635R - 00 / 004 TOXICOLOGICAL REVIEW OF VINYL CHLORIDE ( CAS No . 75 - 01 - 4 ) In Support of Summary Information on the Integrated Risk Information System ( IRIS ) May 2000 U.S . Environmental Protection Agency Washington , DC DISCLAIMER This document has been reviewed in accordance with U.S

  17. Ethyl chloride

    Integrated Risk Information System (IRIS)

    Ethyl chloride ; CASRN 75 - 00 - 3 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogenic Eff

  18. Benzyl chloride

    Integrated Risk Information System (IRIS)

    Benzyl chloride ; CASRN 100 - 44 - 7 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogenic E

  19. Allyl chloride

    Integrated Risk Information System (IRIS)

    Allyl chloride ; CASRN 107 - 05 - 1 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for Noncarcinogenic Ef

  20. Metabolic Profiles Reveal Changes in Wild and Cultivated Soybean Seedling Leaves under Salt Stress

    PubMed Central

    Zhang, Jing; Yang, Dongshuang; Li, Mingxia; Shi, Lianxuan

    2016-01-01

    Clarification of the metabolic mechanisms underlying salt stress responses in plants will allow further optimization of crop breeding and cultivation to obtain high yields in saline-alkali land. Here, we characterized 68 differential metabolites of cultivated soybean (Glycine max) and wild soybean (Glycine soja) under neutral-salt and alkali-salt stresses using gas chromatography-mass spectrometry (GC-MS)-based metabolomics, to reveal the physiological and molecular differences in salt tolerance. According to comparisons of growth parameters under the two kinds of salt stresses, the level of inhibition in wild soybean was lower than in cultivated soybean, especially under alkali-salt stress. Moreover, wild soybean contained significantly higher amounts of phenylalanine, asparagine, citraconic acid, citramalic acid, citric acid and α-ketoglutaric acid under neutral-salt stress, and higher amounts of palmitic acid, lignoceric acid, glucose, citric acid and α-ketoglutaric acid under alkali-salt stress, than cultivated soybean. Further investigations demonstrated that the ability of wild soybean to salt tolerance was mainly based on the synthesis of organic and amino acids, and the more active tricarboxylic acid cycle under neutral-salt stress. In addition, the metabolite profiling analysis suggested that the energy generation from β-oxidation, glycolysis and the citric acid cycle plays important roles under alkali-salt stress. Our results extend the understanding of mechanisms involved in wild soybean salt tolerance and provide an important reference for increasing yields and developing salt-tolerant soybean cultivars. PMID:27442489

  1. Historical and Experimental Studies of Alkali and Trinitrotoluene Reaction

    DTIC Science & Technology

    1975-04-01

    Certainly attempts at titration in aqueous media would be futile in light of the virtually non- Bxiste•ut acidic properties of TNT. B. Production of Red...to get an addition compound of TNT and methyl alcohol which is the nitronic acid from which the alkali metal salts are derived. Hantzsch 4 originally...of quinol nitrol acids . The colored compounds formed by nitro-substituted aromatic com- pounds in alcoholic alkaline media occur only when one or more

  2. Electrode potentials of tungsten in fused alkali chlorides

    NASA Astrophysics Data System (ADS)

    Ivanov, A. B.; Volkovich, V. A.; Poskryakov, D. A.; Vasin, B. D.; Griffiths, T. R.

    2016-09-01

    Anodic dissolution of tungsten was studied at 823-1173 K in the melts based on NaCl-CsCl, NaCl-KCl-CsCl and LiCl-KCl-CsCl eutectic mixtures. The process results in the formation of W(IV) ions. Prolonged contact with silica results in oxidation W(IV) ions and decreasing tungsten concentration in the electrolyte due to formation of volatile higher oxidation state chloro- and oxychloro-species. Tungsten electrode potentials were measured in NaCl-CsCl and NaCl-KCl-CsCl based melts using potentiometry.

  3. Purification of alkali metal nitrates

    DOEpatents

    Fiorucci, Louis C.; Gregory, Kevin M.

    1985-05-14

    A process is disclosed for removing heavy metal contaminants from impure alkali metal nitrates containing them. The process comprises mixing the impure nitrates with sufficient water to form a concentrated aqueous solution of the impure nitrates, adjusting the pH of the resulting solution to within the range of between about 2 and about 7, adding sufficient reducing agent to react with heavy metal contaminants within said solution, adjusting the pH of the solution containing reducing agent to effect precipitation of heavy metal impurities and separating the solid impurities from the resulting purified aqueous solution of alkali metal nitrates. The resulting purified solution of alkali metal nitrates may be heated to evaporate water therefrom to produce purified molten alkali metal nitrate suitable for use as a heat transfer medium. If desired, the purified molten form may be granulated and cooled to form discrete solid particles of alkali metal nitrates.

  4. Thermodynamic Properties of Magnesium Chloride Hydroxide Hydrate (Mg3Cl(OH)5:4H2O, Phase 5), and Its importance to Nuclear Waste Isolation in Geological Repositories in Salt Formations

    NASA Astrophysics Data System (ADS)

    Xiong, Y.; Deng, H.; Nemer, M. B.; Johnsen, S.

    2009-12-01

    MgO (bulk, pure MgO corresponding to the mineral periclase) is the only engineered barrier certified by the Environmental Protection Agency for emplacement in the Waste Isolation Pilot Plant (WIPP) in the US, and an Mg(OH)2-based engineered barrier (bulk, pure Mg(OH)2 corresponding to brucite) is to be employed in the Asse repository in Germany. Both the WIPP and the Asse are located in salt formations. The WIPP is a U.S. Department of Energy geological repository being used for the permanent disposal of defense-related transuranic waste (TRU waste). The repository is 655 m below the surface, and is situated in the Salado Formation, a Permian salt bed mainly composed of halite, and of lesser amounts of polyhalite, anhydrite, gypsum, magnesite, clays and quartz. The WIPP Generic Weep Brine (GWB), a Na-Mg-Cl dominated brine, is associated with the Salado Formation. The previous vendor for MgO for the WIPP was Premier Chemicals and the current vendor is Martin Marietta Materials. Experimental studies of both Premier MgO and Martin Marietta MgO with the GWB at SNL indicate the formation of magnesium chloride hydroxide hydrate, Mg3Cl(OH)5:4H2O, termed as phase 5. However, this important phase is lacking in the existing thermodynamic database. In this study, the solubility constant of phase 5 is determined from a series of solubility experiments in MgCl2-NaCl solutions. The solubility constant at 25 oC for the following reaction, Mg3Cl(OH)5:4H2O + 5H+ = 3Mg2+ + 9H2O(l) + Cl- is recommended as 43.21±0.33 (2σ) based on the Specific Interaction Theory (SIT) model for extrapolation to infinite dilution. The log K obtained via the Pitzer equations is identical to the above value within the quoted uncertainty. The Gibbs free energy and enthalpy of formation for phase 5 at 25 oC are derived as -3384±2 (2σ) kJ mol-1 and -3896±6 (2σ) kJ mol-1, respectively. The standard entropy and heat capacity of phase 5 at 25 oC are estimated as 393±20 J mol-1 K-1 and 374±19 J mol-1 K

  5. Experimental alkali feldspar dissolution at 100 degree C by carboxylic acids and their anions

    SciTech Connect

    Stoessell, R.K. ); Pittman, E.D. )

    1990-05-01

    Feldspar dissolution will enhance sandstone porosity if the released aluminum can be transported away in the subsurface waters. Carboxylic acids have been proposed to provide hydrogen ions to promote dissolution and anions to complex aqueous aluminum to keep it in solution. However, the hydrogen ions should react quickly following acid generation in source beds, leaving monocarboxylic anions with lesser amounts of dicarboxylic acids and their anions on feldspar dissolution and the apparent complexing of aluminum in solution. Two-week dissolution experiments of alkali feldspar were run at 100{degree}C and 300 bars in acetic acid, oxalic acid, and sodium salt solutions of chloride, acetate, propionate, oxalate, and malonate. Extrapolation of the results, to reservoir conditions during sandstone diagenesis, implies that concentrations of aluminum-organic complexes are not significant for acetate and propionate and are possibly significant for oxalate and malonate, depending upon fluid compositions. Propionate appeared to inhibit feldspar dissolution and hence might decrease secondary porosity formation. Increases in aluminum concentrations in the presence of oxalic and acetic acid solutions appear to be due to enhanced dissolution kinetics and greater aluminum solubility under low-pH conditions. Such low-pH fluids are generally absent in subsurface reservoirs, making this an unlikely mechanism for enhancing porosity. Furthermore, the observed thermal instability of oxalate and malonate anions explains their general low concentrations in subsurface fluids which limits their aluminum complexing potential in reservoirs during late diagenesis.

  6. Role of alkali carbonate and salt in topochemical synthesis of K1/2Na1/2NbO3 and NaNbO3 templates

    NASA Astrophysics Data System (ADS)

    Lee, Jae-Seok; Jeon, Jae-Ho; Choi, Si-Young

    2013-11-01

    Since the properties of lead-free piezoelectric materials have thus far failed to meet those of lead-based materials, either chemical doping or morphological texturing should be employed to improve the piezoelectric properties of lead-free piezoelectric ceramics. The goal of this study was to synthesize plate-like K1/2Na1/2NbO3 and NaNbO3 particles, which are the most favorable templates for morphological texturing of K1/2Na1/2NbO3 ceramics. To achieve this goal, Bi2.5Na3.5Nb5O18 precursors in a plate-like shape were first synthesized and subsequently converted into K1/2Na1/2NbO3 or NaNbO3 particles that retain the morphology of Bi2.5Na3.5Nb5O18. In this study, we found that sodium or potassium carbonate does not play a major role in converting the Bi2.5Na3.5Nb5O18 precursor to K1/2Na1/2NbO3 or NaNbO3, on the contrary to previous reports; however, the salt contributes to the conversion reaction. All synthesis processes have been performed via a molten salt method, and scanning electron microscopy, scanning probe microscopy, and inductively coupled plasma mass spectroscopy were used to characterize the synthesized K1/2Na1/2NbO3 or NaNbO3 templates.

  7. Alkali metal and alkali earth metal gadolinium halide scintillators

    DOEpatents

    Bourret-Courchesne, Edith; Derenzo, Stephen E.; Parms, Shameka; Porter-Chapman, Yetta D.; Wiggins, Latoria K.

    2016-08-02

    The present invention provides for a composition comprising an inorganic scintillator comprising a gadolinium halide, optionally cerium-doped, having the formula A.sub.nGdX.sub.m:Ce; wherein A is nothing, an alkali metal, such as Li or Na, or an alkali earth metal, such as Ba; X is F, Br, Cl, or I; n is an integer from 1 to 2; m is an integer from 4 to 7; and the molar percent of cerium is 0% to 100%. The gadolinium halides or alkali earth metal gadolinium halides are scintillators and produce a bright luminescence upon irradiation by a suitable radiation.

  8. [Underlying mechanisms and related techniques of stand establishment of cotton on coastal saline-alkali soil].

    PubMed

    Dong, He-Zhong

    2012-02-01

    Stand establishment is the most difficult step for cotton planting on coastal saline-alkali soil. To establish and improve the techniques for stand establishment is the key in the production of high-yielding cotton on saline-alkali soil. Based on the previous studies and our own research progress in this field, this paper reviewed the effects and the underlying mechanisms of making unequal salt distribution in root zone, increasing soil moisture and temperature, establishing under-mulching greenhouse, and introducing seed coating agent in promoting stand establishment of cotton on saline-alkali soil. It was suggested that under the conditions of the average salt content in topsoil being not able to reduce, improving at least partial root zone environment through the induction of unequal salt distribution in the root zone and increasing soil moisture and temperature could significantly reduce salt injury and improve stand establishment. Flat seeding under plastic mulching on low-salinity soil, furrow seeding with mulching on moderate- or high-salinity soil, early mulching before sowing on rain-fed saline soil, and late sowing of short-season cotton in heat-limited area were the efficient techniques for improving the stand establishment of cotton on coastal saline-alkali soil. This review could provide full guarantee for the cotton stand establishment on coastal saline-alkali soil.

  9. Alkali-treated titanium selectively regulating biological behaviors of bacteria, cancer cells and mesenchymal stem cells.

    PubMed

    Li, Jinhua; Wang, Guifang; Wang, Donghui; Wu, Qianju; Jiang, Xinquan; Liu, Xuanyong

    2014-12-15

    Many attentions have been paid to the beneficial effect of alkali-treated titanium to bioactivity and osteogenic activity, but few to the other biological effect. In this work, hierarchical micro/nanopore films were prepared on titanium surface by acid etching and alkali treatment and their biological effects on bacteria, cancer cells and mesenchymal stem cells were investigated. Gram-positive Staphylococcus aureus, Gram-negative Escherichia coli, and human cholangiocarcinoma cell line RBE were used to investigate whether alkali-treated titanium can influence behaviors of bacteria and cancer cells. Responses of bone marrow mesenchymal stem cells (BMMSCs) to alkali-treated titanium were also subsequently investigated. The alkali-treated titanium can potently reduce bacterial adhesion, inhibit RBE and BMMSCs proliferation, while can better promote BMMSCs osteogenesis and angiogenesis than acid-etched titanium. The bacteriostatic ability of the alkali-treated titanium is proposed to result from the joint effect of micro/nanotopography and local pH increase at bacterium/material interface due to the hydrolysis of alkali (earth) metal titanate salts. The inhibitory action of cell proliferation is thought to be the effect of local pH increase at cell/material interface which causes the alkalosis of cells. This alkalosis model reported in this work will help to understand the biologic behaviors of various cells on alkali-treated titanium surface and design the intended biomedical applications.

  10. Durability of Alkali Activated Blast Furnace Slag

    NASA Astrophysics Data System (ADS)

    Ellis, K.; Alharbi, N.; Matheu, P. S.; Varela, B.; Hailstone, R.

    2015-11-01

    The alkali activation of blast furnace slag has the potential to reduce the environmental impact of cementitious materials and to be applied in geographic zones where weather is a factor that negatively affects performance of materials based on Ordinary Portland Cement. The scientific literature provides many examples of alkali activated slag with high compressive strengths; however research into the durability and resistance to aggressive environments is still necessary for applications in harsh weather conditions. In this study two design mixes of blast furnace slag with mine tailings were activated with a potassium based solution. The design mixes were characterized by scanning electron microscopy, BET analysis and compressive strength testing. Freeze-thaw testing up to 100 freeze-thaw cycles was performed in 10% road salt solution. Our findings included compressive strength of up to 100 MPa after 28 days of curing and 120 MPa after freeze-thaw testing. The relationship between pore size, compressive strength, and compressive strength after freeze-thaw was explored.

  11. Crystal structure of 4-carbamoylpyridinium chloride

    PubMed Central

    Fellows, Simon M.; Prior, Timothy J.

    2016-01-01

    The hydro­chloride salt of isonicotinamide, C6H7N2O+·Cl−, has been synthesized from a dilute solution of hydro­chloric acid in aceto­nitrile. The compound displays monoclinic symmetry (space group C2/c) at 150 K, similar to the related hydro­chloride salt of nicotinamide. The asymmetric unit contains one protonated isonicotinamide mol­ecule and a chloride anion. An array of hydrogen-bonding inter­actions, including a peculiar bifurcated pyridinium–chloride inter­action, results in linear chains running almost perpendicularly in the [150] and [1-50] directions within the structure. A description of the hydrogen-bonding network and comparison with similar compounds are presented. PMID:27375858

  12. Strategies for salt reduction in foods.

    PubMed

    Toldrá, Fidel; Barat, José M

    2012-04-01

    The amounts of sodium chloride in the formulation of a variety of foods like bakery, meats and dairy foods, ready meals, sauces and snacks, are relatively large and thus, have a strong contribution on the salt dietary intake. There is a clear demand by the consumers and medical associations to reduce the salt content in foods. Different strategies have been proposed and most of them consist of the replacement of sodium chloride by other salts and the addition of other substances for an acceptable sensory quality. The recent patents for salt reduction and their applications in foods are reviewed in this manuscript.

  13. Properties and Performance of Alkali-Activated Concrete

    NASA Astrophysics Data System (ADS)

    Thomas, Robert J.

    Alkali-activated concrete (AAC) made with industrial byproducts as the sole binder is rapidly emerging as a sustainable alternative to ordinary portland cement concrete (PCC). Despite its exemplary mechanical performance and durability, there remain several barriers to widespread commercialization of AAC. This dissertation addresses several of these barriers. Mathematical models are proposed which efficiently and accurately predict the compressive strength of AAC as a function of activator composition, binder type, and curing condition. The relationships between compressive strength and other mechanical properties (i.e., tensile strength and modulus of elasticity) are discussed, as are stress-strain relationships. Several aspects related to the durability of AAC are also discussed, including dimensional stability under drying conditions, alkali-silica reactivity, and chloride permeability. The results of these experimental investigations are disseminated in the context of real-world applicability.

  14. Skin and soft tissue necrosis from calcium chloride in a deicer.

    PubMed

    Kim, Min P; Raho, Vittorio J; Mak, John; Kaynar, A Murat

    2007-01-01

    Calcium chloride salt is the principle ingredient of many commercially available deicers. Calcium chloride melts snow and ice by its osmotic action. We present a case of skin and soft tissue necrosis associated with the use of a calcium chloride-containing deicer. Although calcium chloride is known to produce soft tissue necrosis if it extravasates during intravenous administration, necrosis and skin sloughing has rarely been described after topical exposure to this salt. Calcium chloride likely produces tissue injury from the heat liberated by mixing calcium chloride with water (exothermic reaction) and from direct calcium deposits in the skin (calcinosis cutis) and soft tissue.

  15. Upgrading platform using alkali metals

    DOEpatents

    Gordon, John Howard

    2017-01-17

    A method for removing sulfur, nitrogen or metals from an oil feedstock. The method involves reacting the oil feedstock with an alkali metal and a radical capping substance. The alkali metal reacts with the metal, sulfur or nitrogen content to form one or more inorganic products and the radical capping substance reacts with the carbon and hydrogen content to form a hydrocarbon phase. The inorganic products may then be separated out from the hydrocarbon phase.

  16. Upgrading platform using alkali metals

    SciTech Connect

    Gordon, John Howard

    2014-09-09

    A process for removing sulfur, nitrogen or metals from an oil feedstock (such as heavy oil, bitumen, shale oil, etc.) The method involves reacting the oil feedstock with an alkali metal and a radical capping substance. The alkali metal reacts with the metal, sulfur or nitrogen content to form one or more inorganic products and the radical capping substance reacts with the carbon and hydrogen content to form a hydrocarbon phase. The inorganic products may then be separated out from the hydrocarbon phase.

  17. Alkali-metalated forms of thiacalix[4]arenes.

    PubMed

    Zeller, Jürgen; Radius, Udo

    2006-11-13

    The alkali metal salts [TCALi4] (1), [TCANa4] (2), and [TCALK4] (3) of fully deprotonated p-tert-butyltetrathiacalix[4]arene (H(4)TCA) are readily available from the reactions of thiacalix[4]arene and n-BuLi, NaH, or KH as deprotonating reagents. Crystals of the sodium salts 2 and the potassium salt 3 suitable for X-ray diffraction were obtained in the form of the pyridine solvates [(TCA)2Na8.8py] (2.8py) and [(TCA)2K(8).8py] (3.8py). These molecules are dimers in the solid state but are structurally not related. In addition, the reaction of H(4)TCA and lithium hydroxide afforded the structurally characterized complex [(TCA)Li5(OH).4THF] (4). The molecular structure of 4 as well as the structures of 2.8py and 3.8py reveal a close relationship to the corresponding alkali metal salts of the calix[4]arenes.

  18. Comparison of Ionomic and Metabolites Response under Alkali Stress in Old and Young Leaves of Cotton (Gossypium hirsutum L.) Seedlings

    PubMed Central

    Guo, Rui; Shi, LianXuan; Yang, ChunWu; Yan, ChangRong; Zhong, XiuLi; Liu, Qi; Xia, Xu; Li, HaoRu

    2016-01-01

    Soil salinization is an important agriculture-related environmental problem. Alkali stress and salt stress strongly influence the metabolic balance in plants. Salt and alkali stresses exert varied effects on old and young tissues, which display different adaptive strategies. In this study, we used cotton (Gossypium hirsutum L.) plants as experimental material to investigate whether alkali stress induces ionic and metabolism changes in old and young leaves of cotton plants exposed to alkali stress. Results showed that alkali stress exerted a considerably stronger growth inhibition on old leaves than on young leaves. Under alkali stress, young leaves can maintain low Na and high K contents and retain relatively stable tricarboxylic acid cycle, resulting in greater accumulation of photosynthetic metabolites. In terms of metabolic response, the young and old leaves clearly displayed different mechanisms of osmotic regulation. The amounts of inositol and mannose significantly increased in both old and young leaves of cotton exposed to alkali stress, and the extent of increase was higher in young leaves than in old leaves. In old leaves, synthesis of amino acids, such as GABA, valine, and serine, was dramatically enhanced, and this phenomenon is favorable for osmotic adjustment and membrane stability. Organs at different developmental stages possibly display different mechanisms of metabolic regulation under stress condition. Thus, we propose that future investigations on alkali stress should use more organs obtained at different developmental stages. PMID:27933088

  19. Effects of pH and Salts on Physical and Mechanical Properties of Pea Starch Films.

    PubMed

    Choi, W S; Patel, D; Han, J H

    2016-07-01

    To identify the significant contribution of intermolecular hydrogen bonds of starch molecules to the film structure formation, pH of film-forming solutions was adjusted and also various salts (NaCl, CaCl2 , CaSO4 , and K2 SO4 ) were mixed into the glycerol-plasticized pea starch film. The film made from pH 7 possessed the highest tensile strength-at-break (2 times) and elastic modulus (4 to 15 times) and the lowest elongation-at-break compared with those of the films made from acid and alkali environments. The pH 7 film also has the highest film density and the lowest total soluble matter. At the level of 0.01 to 0.1 M of CaSO4 and 0.1 M of K2 SO4 in a kilogram of starch, the water solubility of the film increased, while chloride salts slightly lowered the solubility. NaCl and CaSO4 reduced water vapor permeability (WVP), while CaCl2 slightly increased WVP at 0.01 and 0.06 M concentrations, and K2 SO4 significantly increased WVP at 0.03 and 0.15 M. Presence of salts increased tensile strength (5 to 14 times than the control films) and elastic modulus (35 to 180 times) of starch film at 0.01 to 0.03 M of CaSO4 and K2 SO4 . Elongation-at-break increased significantly as salt concentration increases to an optimal level. However, when the concentration exceeded above the optimal level, the E of starch films decreased and showed no significant difference from the control film. Overall, the addition of salts modified physical and mechanical properties of pea starch films more than pH adjustment without any salt addition.

  20. Al/Cl2 molten salt battery

    NASA Technical Reports Server (NTRS)

    Giner, J.

    1972-01-01

    Molten salt battery has been developed with theoretical energy density of 5.2 j/kg (650 W-h/lb). Battery, which operates at 150 C, can be used in primary mode or as rechargeable battery. Battery has aluminum anode and chlorine cathode. Electrolyte is mixture of AlCl3, NaCl, and some alkali metal halide such as KCl.

  1. Alternative Electrochemical Salt Waste Forms, Summary of FY11-FY12 Results

    SciTech Connect

    Riley, Brian J.; Mccloy, John S.; Crum, Jarrod V.; Lepry, William C.; Rodriguez, Carmen P.; Windisch, Charles F.; Matyas, Josef; Westman, Matthew P.; Rieck, Bennett T.; Lang, Jesse B.; Olszta, Matthew J.; Pierce, David A.

    2014-01-17

    The Fuel Cycle Research and Development Program, sponsored by the U.S. Department of Energy Office of Nuclear Energy, is currently investigating alternative waste forms for wastes generated from nuclear fuel processing. One such waste results from an electrochemical separations process, called the “Echem” process. The Echem process utilizes a molten KCl-LiCl salt to dissolve the fuel. This process results in a spent salt containing alkali, alkaline earth, lanthanide halides and small quantities of actinide halides, where the primary halide is chloride with a minor iodide fraction. Pacific Northwest National Laboratory (PNNL) is concurrently investigating two candidate waste forms for the Echem spent-salt: high-halide minerals (i.e., sodalite and cancrinite) and tellurite (TeO2)-based glasses. Both of these candidates showed promise in fiscal year (FY) 2009 and FY2010 with a simplified nonradioactive simulant of the Echem waste. Further testing was performed on these waste forms in FY2011 and FY2012 to assess the possibility of their use in a sustainable fuel cycle. This report summarizes the combined results from FY2011 and FY2012 efforts.

  2. Chloroaluminate molten salt electrolytes and vanadium pentoxide xerogel cathodes for high energy density batteries

    NASA Astrophysics Data System (ADS)

    Xie, Jian

    The work presented here is part of an effort to develop a new type of battery which uses an alkali metal such as lithium or sodium or the alkaline earth magnesium, as the anode, a V2O5 xerogel as cathode, and a 1-ethyl-3-methylimidazolium chloride/aluminum chloride room temperature molten salt as electrolyte. First, the stability of the electrolyte was studied. The electrochemistry of 1-ethyl-3-methylimidazolium chloride (EMIC), the organic component of the 1-ethyl-3-methylimidazolium chloride/aluminum chloride molten salt, was examined in acetonitrile. Cyclic voltammetry and differential pulse voltammetry were used to study the reduction of EMI+, the cation of EMIC. Controlled potential coulometry was used to determine the number of electrons involved in the EMI+ reduction process. EMI+ reduction was found to be a one-electron, diffusion controlled process occurring at -2.35V (vs. a reference electrode consisting of a Ag wire in 0.1 M tetra-n-butylammonium perchlorate (TBAP)/acetonitrile solution) in 0.1M TBAP/acetonitrile solution. Two products were generated from the reduction, which are oxidized at about -0.45 and -0.65V. Mass spectroscopy data for these two products suggest that they are degradation products of EMI+. The major products of EMI+ reduction are not electrochemically active within the available potential window. Thus, small amounts of these species should not have a serious effect on the operation of a cell using an EMIC/AlCl3 electrolyte. The second project was to develop a method for buffering a melt which contains free Mg2+ ion for insertion into a V2O 5 xerogel cathode. The buffering of melts with MgCl2 and Mg metal was investigated starting with both acidic and basic melts. The following reaction is proposed for the Mg ribbon in acidic melt: 8Al2Cl - 7+3Mg→2Al+3Mg2++14AlCl -4 This was verified by electrochemical and atomic emission spectroscopy inductively coupled plasma (AES/ICP) data. Finally, the intercalation of Li+, Na+, and Mg2+ ions

  3. Hydrothermal alkali metal catalyst recovery process

    DOEpatents

    Eakman, James M.; Clavenna, LeRoy R.

    1979-01-01

    In a coal gasification operation or similar conversion process carried out in the presence of an alkali metal-containing catalyst wherein solid particles containing alkali metal residues are produced, alkali metal constituents are recovered from the particles primarily in the form of water soluble alkali metal formates by treating the particles with a calcium or magnesium-containing compound in the presence of water at a temperature between about 250.degree. F. and about 700.degree. F. and in the presence of added carbon monoxide. During the treating process the water insoluble alkali metal compounds comprising the insoluble alkali metal residues are converted into water soluble alkali metal formates. The resultant aqueous solution containing water soluble alkali metal formates is then separated from the treated particles and any insoluble materials formed during the treatment process, and recycled to the gasification process where the alkali metal formates serve as at least a portion of the alkali metal constituents which comprise the alkali metal-containing catalyst. This process permits increased recovery of alkali metal constituents, thereby decreasing the overall cost of the gasification process by reducing the amount of makeup alkali metal compounds necessary.

  4. Solid state tetrachloroaluminate storage battery having a transition metal chloride cathode

    NASA Astrophysics Data System (ADS)

    Vaughn, R. L.

    1983-12-01

    In accordance with this invention, it has been found that highly efficient, lightweight, thermally activated power sources can be fabricated by utilizing a transition metal chloride such as cupric chloride, ferric chloride, or molybdenum chloride as the cathode; and a lithium metal or lithium-aluminum or lithium-silicon alloy as the anode in combination with an alkali metal tetrachloroaluminate solid electrolyte. The power source may comprise a single cell or a stack of individual cells. A typical cell is a three layered pellet composed of a lithium alloy anode, a separating alkali metal tetrachloroaluminate solid electrolyte sandwiched between the anode and a cathode which, in turn, is composed of a mixture of the transition metal chloride and graphite. The cell is totally inert until raised to its operating temperature by any conventional heating means.

  5. Alkali Metal Cluster Theory.

    NASA Astrophysics Data System (ADS)

    Chen, Jian

    Available from UMI in association with The British Library. Requires signed TDF. In this thesis, we apply the tight-binding Hubbard model to alkali metal clusters with Hartree-Fock self-consistent methods and perturbation methods for the numerical calculations. We have studied the relation between the equilibrium structures and the range of the hopping matrix elements in the Hubbard Hamiltonian. The results show that the structures are not sensitive to the interaction range but are determined by the number of valence electrons each atom has. Inertia tensors are used to analyse the symmetries of the clusters. The principal axes of the clusters are determined and they are the axes of rotational symmetries of clusters if the clusters have any. The eigenvalues of inertia tensors which are the indication of the deformation of clusters are compared between our model and the ellipsoidal jellium model. The agreement is good for large clusters. At a finite temperature, the thermal motion fluctuates the structures. We defined a fluctuation function with the distance matrix of a cluster. The fluctuation has been studied with the Monte-Carlo simulation method. Our studies show that the clusters remain in the solid state when temperature is low. The small values of fluctuation functions indicates the thermal vibration of atoms around their equilibrium positions. If the temperature is high, the atoms are delocalized. The cluster melts and enters the liquid region. The cluster melting is simulated by the Monte-Carlo simulation with the fluctuation function we defined. Energy levels of clusters are calculated from the Hubbard model. Ionization potentials and magic numbers are also obtained from these energy levels. The results confirm that the Hubbard model is a good approximation for a small cluster. The excitation energy is presented by the difference between the original level and excited level, and the electron-hole interactions. We also have studied cooling of clusters

  6. Salt Complexation in Block Copolymer Thin Films

    SciTech Connect

    Kim,S.; Misner, M.; Yang, L.; Gang, O.; Ocko, B.; Russell, T.

    2006-01-01

    Ion complexation within cylinder-forming block copolymer thin films was found to affect the ordering process of the copolymer films during solvent annealing, significantly enhancing the long-range positional order. Small amounts of alkali halide or metal salts were added to PS-b-PEO, on the order of a few ions per chain, where the salt complexed with the PEO block. The orientation of the cylindrical microdomains strongly depended on the salt concentration and the ability of the ions to complex with PEO. The process shows large flexibility in the choice of salt used, including gold or cobalt salts, whereby well-organized patterns of nanoparticles can be generated inside the copolymer microdomains. By further increasing the amount of added salts, the copolymer remained highly ordered at large degrees of swelling and demonstrated long-range positional correlations of the microdomains in the swollen state, which holds promise as a route to addressable media.

  7. Investigation of structural properties associated with alkali-silica reaction by means of macro- and micro-structural analysis

    SciTech Connect

    Mo Xiangyin . E-mail: moxiangyin@njnu.edu.cn; Fournier, Benoit

    2007-02-15

    Structural properties associated with alkali-silica reaction were systematically investigated by means of macro-structural accelerated mortar prism expansion levels testing, combined with micro-structural analysis. One part of this study is to determine the reactivity of the aggregate by means of accelerated mortar bar tests, and also to evaluate perlite aggregate constituents, especially the presence of deleterious components and find main causes of the alkali-silica reaction, which was based on the petrographic studies by optical microscope and the implication of X-ray diffraction on the aggregate. Results implied that the aggregate was highly alkali-silica reactive and the main micro-crystalline quartz-intermediate character and matrix that is mainly composed of chalcedony are potentially suitable for alkali-silica reaction. The other part is to study the long-term effect of lithium salts against alkali-silica reaction by testing accelerated mortar prism expansion levels. The macro-structural results were also consistent with the micro-structural mechanisms of alkali-silica reaction of mortar prisms containing this aggregate and the effect of chemical admixtures by means of the methods of scanning electron microscope-X-ray energy-dispersive spectroscopy and X-ray diffraction. It was indicated by these techniques that lithium salts, which were introduced into concrete containing reactive aggregate at the mixing stage, suppressed the alkali-silica reaction by producing non-expansive crystalline materials.

  8. Process for recovering alkali metals and sulfur from alkali metal sulfides and polysulfides

    DOEpatents

    Gordon, John Howard; Alvare, Javier

    2016-10-25

    Alkali metals and sulfur may be recovered from alkali monosulfide and polysulfides in an electrolytic process that utilizes an electrolytic cell having an alkali ion conductive membrane. An anolyte solution includes an alkali monosulfide, an alkali polysulfide, or a mixture thereof and a solvent that dissolves elemental sulfur. A catholyte includes molten alkali metal. Applying an electric current oxidizes sulfide and polysulfide in the anolyte compartment, causes alkali metal ions to pass through the alkali ion conductive membrane to the catholyte compartment, and reduces the alkali metal ions in the catholyte compartment. Liquid sulfur separates from the anolyte solution and may be recovered. The electrolytic cell is operated at a temperature where the formed alkali metal and sulfur are molten.

  9. Facile Preparation of Chloride-Conducting Membranes: First Step towards a Room-Temperature Solid-State Chloride-Ion Battery.

    PubMed

    Gschwind, Fabienne; Steinle, Dominik; Sandbeck, Daniel; Schmidt, Celine; von Hauff, Elizabeth

    2016-12-01

    Three types of chloride-conducting membranes based on polyvinyl chloride, commercial gelatin, and polyvinyldifluoride-hexafluoropolymer are introduced in this report. The polymers are mixed with chloride-containing salts, such as tetrabutylammonium chloride, and cast to form membranes. We studied the structural properties, thermal stability, and electrochemical response of the membranes to understand chloride migration and transport. Finally, the membranes are tested in a prototype solid-state chloride-ion battery setup. The feasibility of the membranes for their potential use in anion batteries is discussed.

  10. Electrical Resistivity of Alkali Elements.

    DTIC Science & Technology

    1976-01-01

    rubidium, cesium, and francium ) and contains recommended reference values (or provisional or typical values). The compiled data include all the...and information on the electrical resistivity of alkali elements (lithium, sodium, potassium, rubidium, cesium, and francium ) and contains...107Ic. Magnetic Flux Density Dependence o.. .. ... .... 112 4.6. Francium ..........................115j a. Temperature Dependence

  11. An Advanced Flash Suppression Network Involving Alkali Salts

    DTIC Science & Technology

    1984-12-01

    a fuel are: H, 0, OH, H2 , 02, HO2 , and H 0. To include carbon monoxide as a fuelthe species CO and CO2 must be added to this list. Since we are...KOH -54.50 56.90 c, b 12 K02 -25.00 62.00 f 13 Co -26.40 47.20 b 14 CO2 -94.10 51.10 b a) J. Phys. & Chem. Ref. Data, Vol.4, 1975. b) JANAF...23.0000 -4.3000 -21.7186 3738 KH + K02 = KO + KOH -38.3000 4.5000 -39.6410 3839 KH + CO2 = KOH + CO -13.1000 5.7000 -14.7986 3940 KO + KO = K + K02

  12. Evaluation of Alkali Bromide Salts for Potential Pyrochemical Applications

    SciTech Connect

    Prabhat K. Tripathy; Steven D. Herrmann; Guy L. Fredrickson; Tedd E. Lister; Toni Y. Gutknecht

    2013-10-01

    Transient techniques were employed to study the electrochemical behavior, reduction mechanism and transport properties of REBr3 (RE - La, Nd and Gd) in pure LiBr, LiBr-KBr (eutectic) and LiBr-KBr-CsBr (eutectic) melts. Gd(III) showed a reversible single step soluble-insoluble exchange phenomenon in LiBr melt at 973K. Although La (III), Nd(III) and Gd(III) ions showed reversible behavior in eutectic LiBr-KBr melts, these ions showed a combination of temperature dependent reversible and pseudo-reversible behavior. While both La(III) and Gd(III) showed one step reduction, the reduction of Nd(III) was observed to be a two step process. La metal could be electrodeposited from the ternary electrolyte at a temperature of 673K. Various electrochemical measurements suggest that both binary and ternary bromide melts can potentially be used to electrodeposit high purity RE metals at comparatively lower operating temperatures.

  13. Fundamental Properties of Salts

    SciTech Connect

    Toni Y Gutknecht; Guy L Fredrickson

    2012-11-01

    Thermal properties of molten salt systems are of interest to electrorefining operations, pertaining to both the Fuel Cycle Research & Development Program (FCR&D) and Spent Fuel Treatment Mission, currently being pursued by the Department of Energy (DOE). The phase stability of molten salts in an electrorefiner may be adversely impacted by the build-up of fission products in the electrolyte. Potential situations that need to be avoided, during electrorefining operations, include (i) fissile elements build up in the salt that might approach the criticality limits specified for the vessel, (ii) electrolyte freezing at the operating temperature of the electrorefiner due to changes in the liquidus temperature, and (iii) phase separation (non-homogenous solution). The stability (and homogeneity) of the phases can be monitored by studying the thermal characteristics of the molten salts as a function of impurity concentration. Simulated salt compositions consisting of the selected rare earth and alkaline earth chlorides, with a eutectic mixture of LiCl-KCl as the carrier electrolyte, were studied to determine the melting points (thermal characteristics) using a Differential Scanning Calorimeter (DSC). The experimental data were used to model the liquidus temperature. On the basis of the this data, it became possible to predict a spent fuel treatment processing scenario under which electrorefining could no longer be performed as a result of increasing liquidus temperatures of the electrolyte.

  14. Cation effects on interfacial water organization of aqueous chloride solutions. I. Monovalent cations: Li+, Na+, K+, and NH4(+).

    PubMed

    Hua, Wei; Verreault, Dominique; Huang, Zishuai; Adams, Ellen M; Allen, Heather C

    2014-07-17

    The influence of monovalent cations on the interfacial water organization of alkali (LiCl, NaCl, and KCl) and ammonium chloride (NH4Cl) salt solutions was investigated using surface-sensitive conventional vibrational sum frequency generation (VSFG) and heterodyne-detected (HD-)VSFG spectroscopy. It was found in the conventional VSFG spectra that LiCl and NH4Cl significantly perturb water’s hydrogen-bonding network. In contrast, NaCl and KCl had little effect on the interfacial water structure and exhibited weak concentration dependency. The Im χs(2)(ωIR) spectra from HD-VSFG further revealed that, for all chloride solutions, the net transition dipole moments of hydrogen-bonded water molecules (O → H) are oriented more toward the vapor phase relative to neat water. This suggests the presence of an interfacial electric field generated from the formation of an ionic double layer in the interfacial region with a distribution of Cl(-) ions located above the countercations, in agreement with predictions from MD simulations. The magnitude of this electric field shows a small but definite cation specificity and follows the order Li(+) ≈ Na(+) > NH4(+) > K(+). The observed trend was found to be in good agreement with previously published surface potential data.

  15. Structural/Functional Role of Chloride in Photosystem II

    PubMed Central

    Rivalta, Ivan; Amin, Muhamed; Luber, Sandra; Vassiliev, Serguei; Pokhrel, Ravi; Umena, Yasufumi; Kawakami, Keisuke; Shen, Jian-Ren; Kamiya, Nobuo; Bruce, Doug; Brudvig, Gary W.; Gunner, M. R.; Batista, Victor S.

    2011-01-01

    Chloride binding in photosystem II (PSII) is essential for photosynthetic water oxidation. However, the functional roles of chloride and possible binding sites, during oxygen evolution, remain controversial. This paper examines the functions of chloride based on its binding site revealed in the X-ray crystal structure of PSII at 1.9 Å resolution. We find that chloride depletion induces formation of a salt-bridge between D2-K317 and D1-D61 that could suppress proton transfer to the lumen. PMID:21678923

  16. Purification of aqueous plutonium chloride solutions via precipitation and washing.

    SciTech Connect

    Stroud, M. A.; Salazar, R. R.; Abney, Kent David; Bluhm, E. A.; Danis, J. A.

    2003-01-01

    Pyrochemical operations at Los Alamos Plutonium Facility (TA-55) use high temperature melt s of calcium chloride for the reduction of plutonium oxide to plutonium metal and hi gh temperature combined melts of sodium chloride and potassium chloride mixtures for the electrorefining purification of plutonium metal . The remaining plutonium and americium are recovered from thes e salts by dissolution in concentrated hydrochloric acid followed by either solvent extraction or io n exchange for isolation and ultimately converted to oxide after precipitation with oxalic acid . Figur e 1 illustrates the current aqueous chloride flow sheet used for plutonium processing at TA-55 .

  17. Hygroscopic salts and the potential for life on Mars.

    PubMed

    Davila, Alfonso F; Duport, Luis Gago; Melchiorri, Riccardo; Jänchen, Jochen; Valea, Sergio; de Los Rios, Asunción; Fairén, Alberto G; Möhlmann, Diedrich; McKay, Christopher P; Ascaso, Carmen; Wierzchos, Jacek

    2010-01-01

    Hygroscopic salts have been detected in soils in the northern latitudes of Mars, and widespread chloride-bearing evaporitic deposits have been detected in the southern highlands. The deliquescence of hygroscopic minerals such as chloride salts could provide a local and transient source of liquid water that would be available for microorganisms on the surface. This is known to occur in the Atacama Desert, where massive halite evaporites have become a habitat for photosynthetic and heterotrophic microorganisms that take advantage of the deliquescence of the salt at certain relative humidity (RH) levels. We modeled the climate conditions (RH and temperature) in a region on Mars with chloride-bearing evaporites, and modeled the evolution of the water activity (a(w)) of the deliquescence solutions of three possible chloride salts (sodium chloride, calcium chloride, and magnesium chloride) as a function of temperature. We also studied the water absorption properties of the same salts as a function of RH. Our climate model results show that the RH in the region with chloride-bearing deposits on Mars often reaches the deliquescence points of all three salts, and the temperature reaches levels above their eutectic points seasonally, in the course of a martian year. The a(w) of the deliquescence solutions increases with decreasing temperature due mainly to the precipitation of unstable phases, which removes ions from the solution. The deliquescence of sodium chloride results in transient solutions with a(w) compatible with growth of terrestrial microorganisms down to 252 K, whereas for calcium chloride and magnesium chloride it results in solutions with a(w) below the known limits for growth at all temperatures. However, taking the limits of a(w) used to define special regions on Mars, the deliquescence of calcium chloride deposits would allow for the propagation of terrestrial microorganisms at temperatures between 265 and 253 K, and for metabolic activity (no growth) at

  18. Alkylated lariat ethers as solvent extraction reagents: Surveying the extraction of alkali metals by bis-t-octylbenzo-14-crown-4-acetic acid by use of potentiometric two-phase titration

    SciTech Connect

    Sachleben, R.A.; Moyer, B.A.; Case, F.I.; Garmon, S.A.

    1993-01-01

    Two-phase potentiometric titrimetry was used to survey the extraction of alkali metal cations from aqueous chloride solution by the lipophilic, ionizable lariat ether bis-(t-octylbenzo)-14-crown-4-acetic acid (BOB14C4AA) in o-xylene. Analysis of the data indicates that ion-exchange extraction by the crown-carboxylic acid at low loading (i.e., low conversion of BOB14C4AA to its salt form) is stronger for lithium ion than for the other alkali metals. Little or no selectivity occurs at high loadings. In comparison with the long-chain carboxylic acid 2-methyl-2-heptylnonanoic acid (HMHN), BOB14C4AA extracts lithium and sodium at significantly lower pH; in the loading range of 0.1 to 0.7, the pH shift is 1.4-1.8 pH units for sodium ion and 1.7-2.3 pH units for lithium ion. The titration data are interpreted in terms of aggregated organic-phase species. In the case of lithium extraction, clear evidence was found for a species in which neutral BOB14C4AA participates in the organic-phase complexation of the metal cation.

  19. Spectra of Low-Temperature Chlorine Salt Hydrates and Implications for Europa

    NASA Astrophysics Data System (ADS)

    Hanley, J.; Dalton, J. B., III; Chevrier, V. F.; Jamieson, C. S.

    2014-02-01

    Low-temperature spectra of chloride and (per)chlorate salts exhibit diagnostic features that should allow for their detection, if present. Chlorine salts lower the activity of water, limiting potential life.

  20. Materials corrosion in molten lithium fluoride-sodium fluoride-potassium fluoride eutectic salt

    NASA Astrophysics Data System (ADS)

    Olson, Luke Christopher

    Static corrosion studies were undertaken to determine the compatibility of several candidate high temperature materials for a heat transfer loop in a molten alkali fluoride eutectic salt, LiF-NaF-KF: 46.5-11.5-42 mol % (commonly referred to as FLiNaK), as well as a molten chloride near eutectic salt, KCl-MgCl2: 68-32 mol %. Several high temperature alloys: Hastelloy-N, Hastelloy-X, Haynes-230, Inconel-617, and Incoloy-800H, Nb-1Zr, a nearly pure Ni alloy Ni-201, and a C/SiSiC ceramic were exposed to molten FLiNaK at 850°C for 500 h in sealed graphite crucibles under an argon cover gas. Corrosion occurred predominantly from dealloying of Cr from the Cr bearing alloys, an effect that was particularly pronounced at the grain boundaries. Corrosion was noted to occur from selective attack of the Si phase in the C/SiSiC ceramic. Alloy weight-loss/area due to molten fluoride salt exposure correlated with the initial Cr-content of the alloys, and was consistent with the Cr-content measured in the salts after corrosion tests. The alloys' weight-loss/area was also found to correlate to the concentration of carbon present in the nominally 20% Cr containing alloys, due to the formation of chromium carbide phases at the grain boundaries. The corrosion mechanisms for the chloride based salt were found to be similar to those observed in FLiNaK, but the chemical attack was found to be less aggressive. Sulfamate Ni electroplating and Mo plasma spraying of Fe-Ni-Cr alloy coupons was investigated to mitigate Cr dissolution. A chemical vapor deposited pyrolytic carbon and SiC coating was also investigated to protect the C/SiSiC composites. Results indicate that Ni-plating has the potential to provide protection against alloy corrosion in molten fluoride salts. Furthermore, the presence of a chromium-oxide interlayer at the interface of the Ni-plating and alloy substrate can further improve the efficacy of the Ni-plating. The pyrolytic carbon and SiC coating on the C/SiSiC composites

  1. Single crystal to single crystal [2+2] photoreactions in chloride and sulphate salts of 4-amino-cinnamic acid via solid-solution formation: a structural and kinetic study.

    PubMed

    d'Agostino, Simone; Spinelli, Floriana; Boanini, Elisa; Braga, Dario; Grepioni, Fabrizia

    2016-01-31

    A set of molecular salts with general formula [1H]nA·xH2O (1 = 4-amino-cinnamic acid, A(n-) = NO3(-), BF4(-), PF6(-), SO4(2-), x = 0, 1) was prepared and structurally characterized. [1H]Cl and [1H]2SO4·H2O(II) were found to undergo an SCSC stepwise [2+2] photodimerization, which was followed by X-ray diffraction; a kinetic analysis was performed on single crystals of both salts. In the case of [1H]Cl the photoreaction was also studied on polycrystalline materials.

  2. High-temperature vacuum distillation separation of plutonium waste salts

    SciTech Connect

    Garcia, E.

    1996-10-01

    In this task, high-temperature vacuum distillation separation is being developed for residue sodium chloride-potassium chloride salts resulting from past pyrochemical processing of plutonium. This process has the potential of providing clean separation of the salt and the actinides with minimal amounts of secondary waste generation. The process could produce chloride salt that could be discarded as low-level waste (LLW) or low actinide content transuranic (TRU) waste, and a concentrated actinide oxide powder that would meet long-term storage standards (DOE-DTD-3013-94) until a final disposition option for all surplus plutonium is chosen.

  3. SEPARATION OF METAL SALTS BY ADSORPTION

    DOEpatents

    Gruen, D.M.

    1959-01-20

    It has been found that certain metal salts, particularly the halides of iron, cobalt, nickel, and the actinide metals, arc readily absorbed on aluminum oxide, while certain other salts, particularly rare earth metal halides, are not so absorbed. Use is made of this discovery to separate uranium from the rare earths. The metal salts are first dissolved in a molten mixture of alkali metal nitrates, e.g., the eutectic mixture of lithium nitrate and potassium nitrate, and then the molten salt solution is contacted with alumina, either by slurrying or by passing the salt solution through an absorption tower. The process is particularly valuable for the separation of actinides from lanthanum-group rare earths.

  4. Positron-alkali atom scattering

    NASA Technical Reports Server (NTRS)

    Mceachran, R. P.; Horbatsch, M.; Stauffer, A. D.; Ward, S. J.

    1990-01-01

    Positron-alkali atom scattering was recently investigated both theoretically and experimentally in the energy range from a few eV up to 100 eV. On the theoretical side calculations of the integrated elastic and excitation cross sections as well as total cross sections for Li, Na and K were based upon either the close-coupling method or the modified Glauber approximation. These theoretical results are in good agreement with experimental measurements of the total cross section for both Na and K. Resonance structures were also found in the L = 0, 1 and 2 partial waves for positron scattering from the alkalis. The structure of these resonances appears to be quite complex and, as expected, they occur in conjunction with the atomic excitation thresholds. Currently both theoretical and experimental work is in progress on positron-Rb scattering in the same energy range.

  5. Cesium chloride-induced torsades de pointes.

    PubMed

    Wiens, Matthew; Gordon, Wendy; Baulcomb, Daisy; Mattman, Andre; Mock, Tom; Brown, Robert

    2009-09-01

    The chloride salt of cesium, a group 1A element, is gaining popularity as an alternative treatment of advanced cancers. Cesium chloride has primarily been used in cardiovascular research for arrhythmogenesis in animals because of its potassium-blocking effects. The present report describes a 45-year-old woman with metastatic breast cancer who experienced repeated episodes of torsades de pointes polymorphic ventricular tachycardia after several months of oral cesium therapy. There was a clear temporal relationship between cesium ingestion and the arrhythmia, which later resolved following discontinuation of cesium therapy. Serial cesium plasma and whole blood levels were measured over the ensuing six months and pharmacokinetic analysis was performed.

  6. Alkali metal/sulfur battery

    DOEpatents

    Anand, Joginder N.

    1978-01-01

    Alkali metal/sulfur batteries in which the electrolyte-separator is a relatively fragile membrane are improved by providing means for separating the molten sulfur/sulfide catholyte from contact with the membrane prior to cooling the cell to temperatures at which the catholyte will solidify. If the catholyte is permitted to solidify while in contact with the membrane, the latter may be damaged. The improvement permits such batteries to be prefilled with catholyte and shipped, at ordinary temperatures.

  7. Watershed scale chloride storage across a gradient of urbanization

    NASA Astrophysics Data System (ADS)

    Wellen, C. C.; Oswald, C. J.; Oni, S. K.

    2014-12-01

    Sodium chloride is the main de-icing agent used during the winter in Canada and the northern United States. However, little is known about the long term fate, residence time, and ecological effects of chloride. This talk integrates work taking place across three sites in Southern Ontario, Canada: Hamilton Harbour, the Toronto lakeshore, and Lake Simcoe. We quantify chloride inputs, outputs, and changes in storage for a number of watersheds across a gradient of urbanization. For the three winter months (January, February, March), we show that stream water chloride concentrations approach those of brackish waters for urban watersheds. Chloride is also highly persistent, with stream water chloride concentrations decreasing from the winter months and approaching baseline levels only in July. These baseline levels are greater than 100 mg Cl/l in the urban watersheds, suggesting high levels of chloride storage in soil and groundwater. Using road salt application rates and groundwater levels and chloride concentrations, we estimate the magnitude and residence time of the chloride pools in a number of watersheds across a gradient of urbanization. Our results suggest that the magnitude and residence time of chloride storage varies with urbanization and other factors. We show that summer baseflow concentrations do approach the EPA's chronic exposure guideline of 230 mg Cl/l, implying more work is needed to understand the in stream and downstream ecological effects of chloride.

  8. Chloride chemical form in various types of fly ash

    SciTech Connect

    Fenfen Zhu; Masaki Takaoka; Kenji Shiota; Kazuyuki Oshita; Yoshinori Kitajima

    2008-06-01

    Chloride content is a critical problem for the reuse of fly ash as a raw material in cement, and the method used by recyclers to reduce the fly ash chloride content depends on the chemical form of the chlorides. However, limited information is available on the quantitative distribution of chlorides and the identity of some chlorides such as Friedel's salt. We examined chloride forms and percentages using X-ray absorption near edge structure and X-ray diffraction analyses, as well as corresponding washing experiments. Approximately 15% of the chlorine in raw fly ash was estimated to be in the form of NaCl, 10% in KCl, 50% in CaCl{sub 2}, and the remainder in the form of Friedel's salt. Fly ash collected in a bag filter with the injection of calcium hydroxide for acid gas removal (CaFA) contained 35% chlorine as NaCl, 11% as KCl, 37% as CaCl{sub 2}, 13% as Friedel's salt, and the remaining 4% as CaClOH. In fly ash collected in a bag filter with the injection of sodium bicarbonate for acid gas removal (NaFA), approximately 79% of chlorine was in NaCl, 12% was in KCl, and 9% was in Friedel's salt. 25 refs., 4 figs., 4 tabs.

  9. Brine Transport Experiments in Granular Salt

    SciTech Connect

    Jordan, Amy B.; Boukhalfa, Hakim; Caporuscio, Florie Andre; Stauffer, Philip H.

    2016-06-06

    To gain confidence in the predictive capability of numerical models, experimental validation must be performed to ensure that parameters and processes are correctly simulated. The laboratory investigations presented herein aim to address knowledge gaps for heat-generating nuclear waste (HGNW) disposal in bedded salt that remain after examination of prior field and laboratory test data. Primarily, we are interested in better constraining the thermal, hydrological, and physicochemical behavior of brine, water vapor, and salt when moist salt is heated. The target of this work is to use run-of-mine (RoM) salt; however during FY2015 progress was made using high-purity, granular sodium chloride.

  10. CALCIUM CHLORIDE PLANT LOOKING EAST. CALCIUM CHLORIDE BUILDING IN CENTER, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    CALCIUM CHLORIDE PLANT LOOKING EAST. CALCIUM CHLORIDE BUILDING IN CENTER, CALCIUM CHLORIDE STORAGE BUILDING ON RIGHT WITH SA (SODA ASH) BUILDING IN RIGHT BACKGROUND. - Solvay Process Company, Calcium Chloride Plant, Between Willis & Milton Avenues, Solvay, Onondaga County, NY

  11. The chemistry of sodium chloride involvement in processes related to hot corrosion. [in gas turbine engines

    NASA Technical Reports Server (NTRS)

    Stearns, C. A.; Kohl, F. J.; Fryburg, G. C.

    1979-01-01

    Thermodynamic and mass transport calculations, and laboratory experiments elucidating the behavior of sodium chloride in combustion environments, in the deposition process, and in reactions with certain oxides on the surfaces of superalloys are summarized. It was found that some of the ingested salt is separated out of the air stream by the compressor. However, sodium chloride does pass from the compressor to the combustor where numerous chemical reactions take place. Here some of the salt is vaporized to yield gaseous sodium chloride molecules. Hydrogen and oxygen atoms present in the combustion products react with some sodium chloride to yield other gaseous species such as sodium, and a fraction of the salt remains as particulates. Both the gas phase and condensed sodium chloride can lead to sodium sulfate formation by various routes, all of which involve reaction with sulfur oxides and oxygen. In addition to contributing to the formation of sodium sulfate, the sodium chloride can contribute to corrosion directly.

  12. A diffusive anomaly of water in aqueous sodium chloride solutions at low temperatures.

    PubMed

    Kim, Jun Soo; Yethiraj, Arun

    2008-02-14

    Molecular dynamics simulations are presented for the self-diffusion coefficient of water in aqueous sodium chloride solutions. At temperatures above the freezing point of pure water, the self-diffusion coefficient is a monotonically decreasing function of salt concentration. Below the freezing point of pure water, however, the self-diffusion coefficient is a non-monotonic function of salt concentration, showing a maximum at approximately one molal salt. This suggests that sodium chloride, which is considered a structure-making salt at room temperature, becomes a structure-breaking salt at low temperatures. A qualitative understanding of this effect can be obtained by considering the effect of ions on the residence time of water molecules near other water molecules. A consideration of the freezing point depression of aqueous sodium chloride solutions suggests that the self-diffusion coefficient of water in supercooled sodium chloride solutions is always higher than that in pure (supercooled) water at the same temperature.

  13. Regenerable activated bauxite adsorbent alkali monitor probe

    DOEpatents

    Lee, Sheldon H. D.

    1992-01-01

    A regenerable activated bauxite adsorber alkali monitor probe for field applications to provide reliable measurement of alkali-vapor concentration in combustion gas with special emphasis on pressurized fluidized-bed combustion (PFBC) off-gas. More particularly, the invention relates to the development of a easily regenerable bauxite adsorbent for use in a method to accurately determine the alkali-vapor content of PFBC exhaust gases.

  14. Regenerable activated bauxite adsorbent alkali monitor probe

    SciTech Connect

    Lee, S.H.D.

    1991-01-22

    This invention relates to a regenerable activated bauxite adsorber alkali monitor probe for field applications to provide reliable measurement of alkali-vapor 5 concentration in combustion gas with special emphasis on pressurized fluidized-bed combustion (PFBC) off-gas. More particularly, the invention relates to the development of a easily regenerable bauxite adsorbent for use in a method to accurately determine the alkali-vapor content of PFBC 10 exhaust gases.

  15. Regenerable activated bauxite adsorbent alkali monitor probe

    DOEpatents

    Lee, S.H.D.

    1992-12-22

    A regenerable activated bauxite adsorber alkali monitor probe for field applications to provide reliable measurement of alkali-vapor concentration in combustion gas with special emphasis on pressurized fluidized-bed combustion (PFBC) off-gas. More particularly, the invention relates to the development of a easily regenerable bauxite adsorbent for use in a method to accurately determine the alkali-vapor content of PFBC exhaust gases. 6 figs.

  16. (N2)3- radical chemistry via trivalent lanthanide salt/alkali metal reduction of dinitrogen: new syntheses and examples of (N2)2- and (N2)3- complexes and density functional theory comparisons of closed shell Sc3+, Y3+, and Lu3+ versus 4f(9) Dy3+.

    PubMed

    Fang, Ming; Bates, Jefferson E; Lorenz, Sara E; Lee, David S; Rego, Daniel B; Ziller, Joseph W; Furche, Filipp; Evans, William J

    2011-02-21

    New syntheses of complexes containing the recently discovered (N(2))(3-) radical trianion have been developed by examining variations on the LnA(3)/M reductive system that delivers "LnA(2)" reactivity when Ln = scandium, yttrium, or a lanthanide, M = an alkali metal, and A = N(SiMe(3))(2) and C(5)R(5). The first examples of LnA(3)/M reduction of dinitrogen with aryloxide ligands (A = OC(6)R(5)) are reported: the combination of Dy(OAr)(3) (OAr = OC(6)H(3)(t)Bu(2)-2,6) with KC(8) under dinitrogen was found to produce both (N(2))(2-) and (N(2))(3-) products, [(ArO)(2)Dy(THF)(2)](2)(μ-η(2):η(2)-N(2)), 1, and [(ArO)(2)Dy(THF)](2)(μ-η(2):η(2)-N(2))[K(THF)(6)], 2a, respectively. The range of metals that form (N(2))(3-) complexes with [N(SiMe(3))(2)](-) ancillary ligands has been expanded from Y to Lu, Er, and La. Ln[N(SiMe(3))(2)](3)/M reactions with M = Na as well as KC(8) are reported. Reduction of the isolated (N(2))(2-) complex {[(Me(3)Si)(2)N](2)Y(THF)}(2)(μ-η(2):η(2)-N(2)), 3, with KC(8) forms the (N(2))(3-) complex, {[(Me(3)Si)(2)N](2)Y(THF)}(2)(μ-η(2):η(2)-N(2))[K(THF)(6)], 4a, in high yield. The reverse transformation, the conversion of 4a to 3 can be accomplished cleanly with elemental Hg. The crown ether derivative {[(Me(3)Si)(2)N](2)Y(THF)}(2)(μ-η(2):η(2)-N(2))[K(18-crown-6)(THF)(2)] was isolated from reduction of 3 with KC(8) in the presence of 18-crown-6 and found to be much less soluble in tetrahydrofuran (THF) than the [K(THF)(6)](+) salt, which facilitates its separation from 3. Evidence for ligand metalation in the Y[N(SiMe(3))(2)](3)/KC(8) reaction was obtained through the crystal structure of the metallacyclic complex {[(Me(3)Si)(2)N](2)Y[CH(2)Si(Me(2))NSiMe(3)]}[K(18-crown-6)(THF)(toluene)]. Density functional theory previously used only with reduced dinitrogen complexes of closed shell Sc(3+) and Y(3+) was extended to Lu(3+) as well as to open shell 4f(9) Dy(3+) complexes to allow the first comparison of bonding between these four

  17. Optimization of Low Sodium Salts Mix for Shoestring Potatoes.

    PubMed

    Pereira, Heverton Carrara; de Souza, Vanessa Rios; Azevedo, Natália Csizmar; Rodrigues, Daniela Maria; Nunes, Cleiton Antônio; Pinheiro, Ana Carla Marques

    2015-06-01

    Several studies have shown the close relationship between the sodium consumption and health problems such as hypertension and cardiovascular disease. Thus, the demand for products with reduced sodium content, but with sensory quality, is increasing every day. In this context, this study aimed to optimize a low sodium salts mix using sodium chloride, potassium chloride, and monosodium glutamate to the development of shoestring potatoes with low sodium content and high sensory quality, through mixture design and response surface methodology. The salts mix that promotes the same salting power and similar sensory acceptability that the shoestring potatoes with 1.6% sodium chloride (ideal concentration) and at the same time promotes the greatest possible reduction of sodium, about 65%, should provide the composition as follows: 0.48% of sodium chloride, 0.92% of potassium chloride, and 0.43% of monosodium glutamate.

  18. Effect of basic alkali-pickling conditions on the production of lysinoalanine in preserved eggs.

    PubMed

    Zhao, Yan; Luo, Xuying; Li, Jianke; Xu, Mingsheng; Tu, Yonggang

    2015-09-01

    During the pickling process, strong alkali causes significant lysinoalanine (LAL) formation in preserved eggs, which may reduce the nutritional value of the proteins and result in a potential hazard to human health. In this study, the impacts of the alkali treatment conditions on the production of LAL in preserved eggs were investigated. Preserved eggs were prepared using different times and temperatures, and alkali-pickling solutions with different types and concentrations of alkali and metal salts, and the corresponding LAL contents were measured. The results showed the following: during the pickling period of the preserved egg, the content of LAL in the egg white first rapidly increased and then slowly increased; the content of LAL in the egg yolk continued to increase significantly. During the aging period, the levels of LAL in both egg white and egg yolk slowly increased. The amounts of LAL in the preserved eggs were not significantly different at temperatures between 20 and 25ºC. At higher pickling temperatures, the LAL content in the preserved eggs increased. With the increase of alkali concentration in the alkali-pickling solution, the LAL content in the egg white and egg yolk showed an overall trend of an initial increase followed by a slight decrease. The content of LAL produced in preserved eggs treated with KOH was lower than in those treated with NaOH. NaCl and KCl produced no significant effects on the production of LAL in the preserved eggs. With increasing amounts of heavy metal salts, the LAL content in the preserved eggs first decreased and then increased. The LAL content generated in the CuSO4 group was lower than that in either the ZnSO4 or PbO groups.

  19. THE BEHAVIOR OF SUPERALLOY OXIDE FILMS IN MOLTEN SALTS.

    DTIC Science & Technology

    NICKEL ALLOYS , CORROSION), (*FILMS, OXIDES), CORROSION RESISTANT ALLOYS , SALTS, CORROSIVE LIQUIDS, HIGH TEMPERATURE, NICKEL COMPOUNDS, SODIUM...COMPOUNDS, SULFATES, CHLORIDES, CHROMIUM COMPOUNDS, CHROMIUM ALLOYS , MOLYBDENUM ALLOYS , COBALT ALLOYS , ALUMINUM ALLOYS , TITANIUM ALLOYS , IRON ALLOYS , NICKEL, OXIDATION

  20. Alkalis in Coal and Coal Cleaning Products / Alkalia W Węglu I Productach Jego Wzbogacania

    NASA Astrophysics Data System (ADS)

    Bytnar, Krzysztof; Burmistrz, Piotr

    2013-09-01

    In the coking process, the prevailing part of the alkalis contained in the coal charge goes to coke. The content of alkalis in coal (and also in coke) is determined mainly by the content of two elements: sodium and potasium. The presence of these elements in coal is connected with their occurrence in the mineral matter and moisture of coal. In the mineral matter and moisture of the coals used for the coke production determinable the content of sodium is 26.6 up to 62. per cent, whereas that of potassium is 37.1 up to 73.4 per cent of the total content of alkalis. Major carriers of alkalis are clay minerals. Occasionally alkalis are found in micas and feldspars. The fraction of alkalis contained in the moisture of the coal used for the production of coke in the total amount of alkalis contained there is 17.8 up to 62.0 per cent. The presence of sodium and potassium in the coal moisture is strictly connected with the presence of the chloride ions. The analysis of the water drained during process of the water-extracting from the flotoconcentrate showed that the Na to K mass ratio in the coal moisture is 20:1. Increased amount of the alkalis in the coal blends results in increased content of the alkalis in coke. This leads to the increase of the reactivity (CRI index), and to the decrease of strength (CSR index) determined with the Nippon Steel Co. method. W procesie koksowania przeważająca część zawartych we wsadzie węglowym alkaliów przechodzi do koksu. Zawartość alkaliów w węglu, a co za tym idzie i w koksie determinowana jest głównie zawartością dwóch pierwiastków: sodu i potasu. Obecność tych pierwiastków w węglu wiąże się z występowaniem ich w substancji mineralnej i wilgoci węgla. W substancji mineralnej oraz wilgoci węgli stosowanych do produkcji koksu, oznaczona zawartość sodu wynosi od 26.6 do 62.9%, a zawartość potasu od 37.1 do 73.4% alkaliów ogółem. Głównymi nośnikami alkaliów w substancji mineralnej są minera

  1. Phonon spectra of alkali metals

    NASA Astrophysics Data System (ADS)

    Zeković, S.; Vukajlović, F.; Veljković, V.

    1982-10-01

    In this work we used a simple local model pseudopotential which includes screening for the phonon spectra calculations of alkali metals. The results obtained are in very good agreement with experimental data. In some branches of phonon spectra the differences between theoretical and experimental results are within 1-2%, while the maximum error is about 6%. The suggested form of the pseudopotential allows us to describe the phonon spectra of Na, K and Rb with only one, and, at the same time, a unique, parameter. In this case, the maximum disagreements from experiment are 9% for Na, 8% for K and 7% for Rb.

  2. Selective flotation of PVC using gelatin and lignin alkali.

    PubMed

    Yenial, Unzile; Kangal, Olgaç; Güney, Ali

    2013-06-01

    Recycling has become one of the most important issues as a result of increasing waste mass in present day. This is especially important for polymer wastes as they are hard to degenerate in nature. Today, most of the practical methods used for the recycling of waste mass, such as hand sorting, gravity separation, etc., cannot be performed successfully owing to close densities of polymers. Froth flotation can be used successfully and economically for this purpose. The main objective of this study was to investigate the effect of plasticizer reagents and the success of froth flotation at plastic recycling. In this study, lignin alkali and gelatin were used as plasticizer reagents. The effect of these reagents was searched with the parameters of pH, concentration, conditioning and flotation time. In the case of post-consumed polyethylene terephthalate and polyvinyl chloride (PVC), 98.9% purity of PVC was obtained at optimum conditions.

  3. From unexpected reactions to a new family of ionic co-crystals: the case of barbituric acid with alkali bromides and caesium iodide.

    PubMed

    Braga, Dario; Grepioni, Fabrizia; Maini, Lucia; Prosperi, Susanna; Gobetto, Roberto; Chierotti, Michele R

    2010-11-07

    Pressing solid barbituric acid with KBr to prepare samples for IR spectroscopy leads to the formation of an ionic co-crystal, in which the co-former is a classical ionic salt; co-crystal formation is also obtained with the other alkali bromides (LiBr, NaBr, RbBr and CsBr) and with caesium iodide. The simultaneous presence of alkali and halide ions affects the dissolution properties of barbituric acid in water.

  4. Modeling Fate and Transport of Chloride from Deicers in Urban Floodplains: Implications for Urban Planning

    NASA Astrophysics Data System (ADS)

    Ledford, S. H.; Lautz, L.

    2015-12-01

    Road salting in urban areas of the northeastern United States increases chloride concentrations in urban streams. Groundwater storage of saline road runoff results in increased surface water chloride concentrations through time, even in non-winter months. Stream-groundwater (SW-GW) interactions promote buffering of large seasonal swings in stream chloride concentrations, resulting in lower surface water chloride in winter and higher concentrations in summer, relative to streams hydrologically disconnected from riparian floodplains. However, the hydrogeologic processes controlling salt storage and transport in urban floodplain aquifers have not been fully investigated. We developed a 3D numerical groundwater flow and solute transport model of an urban floodplain in Syracuse, New York, using MODFLOW and MT3DMS. We ran the model for 1 year, calibrating to three conditions: water table elevations along a riparian transect, measurements of net groundwater flux to the stream along the 500-m reach, and chloride concentrations in groundwater through time in riparian wells. Chloride enters the riparian aquifer via three pathways: hillslope groundwater discharge, hyporheic exchange, and groundwater recharge during overbank flooding events. Winter overbank flooding events are the primary source of chloride to floodplain sediments. While hillslope groundwater discharge results in relatively uniform chloride through time in high conductivity units, surficial floodplain sediments with lower conductivity have high chloride concentrations from winter overbank flood events. When compared to road salt application rates (up to 20 tons of salt per lane kilometer per year), the 0.013 km2 floodplain holds only a tiny fraction of chloride applied in a watershed (>100 km of road in the watershed). To promote riparian aquifer storage of road salt and buffering of stream chloride concentrations, urban planners should design urban floodplains for frequent winter flooding events, and allow

  5. Process for the disposal of alkali metals

    DOEpatents

    Lewis, Leroy C.

    1977-01-01

    Large quantities of alkali metals may be safely reacted for ultimate disposal by contact with a hot concentrated caustic solution. The alkali metals react with water in the caustic solution in a controlled reaction while steam dilutes the hydrogen formed by the reaction to a safe level.

  6. Iatrogenic salt poisoning in captive sandhill cranes

    USGS Publications Warehouse

    Franson, J.C.; Sileo, L.; Fleming, W.J.

    1981-01-01

    Salt poisoning developed in captive sandhill cranes (Grus canadensis) when sea salt was added to normal drinking water to produce a sodium chloride concentration of 1%. Two of 18 cranes died and 2 were euthanatized when moribund. Muscle weakness, paresis, dyspnea, and depression were observed. Brain and serum sodium, serum uric acid,:and plasma osmolality values were abnormally high. Lesions were those of visceral gout, renal tubular necrosis, nephrosis, and skeletal muscle.necrosis.

  7. Spin Transfer from an Optically Pumped Alkali Vapor to a Solid

    SciTech Connect

    Ishikawa, K.; Patton, B.; Jau, Y.-Y.; Happer, W.

    2007-05-04

    We report enhancement of the spin polarization of {sup 133}Cs nuclei in CsH salt by spin transfer from an optically pumped cesium vapor. The nuclear polarization was 4.0 times the equilibrium polarization at 9.4 T and 137 deg. C, with larger enhancements at lower fields. This work is the first demonstration of spin transfer from a polarized alkali vapor to the nuclei of a solid, opening up new possibilities for research in hyperpolarized materials.

  8. Pyrolytic conversion of plastic and rubber waste to hydrocarbons with basic salt catalysts

    DOEpatents

    Wingfield, Jr., Robert C.; Braslaw, Jacob; Gealer, Roy L.

    1985-01-01

    The invention relates to a process for improving the pyrolytic conversion of waste selected from rubber and plastic to low molecular weight olefinic materials by employing basis salt catalysts in the waste mixture. The salts comprise alkali or alkaline earth compounds, particularly sodium carbonate, in an amount of greater than about 1 weight percent based on the waste feed.

  9. Method of handling radioactive alkali metal waste

    DOEpatents

    Wolson, R.D.; McPheeters, C.C.

    Radioactive alkali metal is mixed with particulate silica in a rotary drum reactor in which the alkali metal is converted to the monoxide during rotation of the reactor to produce particulate silica coated with the alkali metal monoxide suitable as a feed material to make a glass for storing radioactive material. Silica particles, the majority of which pass through a 95 mesh screen or preferably through a 200 mesh screen, are employed in this process, and the preferred weight ratio of silica to alkali metal is 7 to 1 in order to produce a feed material for the final glass product having a silica to alkali metal monoxide ratio of about 5 to 1.

  10. Method of handling radioactive alkali metal waste

    DOEpatents

    Wolson, Raymond D.; McPheeters, Charles C.

    1980-01-01

    Radioactive alkali metal is mixed with particulate silica in a rotary drum reactor in which the alkali metal is converted to the monoxide during rotation of the reactor to produce particulate silica coated with the alkali metal monoxide suitable as a feed material to make a glass for storing radioactive material. Silica particles, the majority of which pass through a 95 mesh screen or preferably through a 200 mesh screen, are employed in this process, and the preferred weight ratio of silica to alkali metal is 7 to 1 in order to produce a feed material for the final glass product having a silica to alkali metal monoxide ratio of about 5 to 1.

  11. Solution-based approaches for making high-density sodalite waste forms to immobilize spent electrochemical salts

    SciTech Connect

    Lepry, William C.; Riley, Brian J.; Crum, Jarrod V.; Rodriguez, Carmen P.; Pierce, David A.

    2013-08-29

    Three different solution-based approaches were taken to make sodalite minerals as a host for a mixed salt simulating the waste generated during the electrochemical separations process of nuclear fuel reprocessing that contains alkali, alkaline earth, and lanthanide chlorides plus trace iodine and actinides. All of the approaches included an aqueous solution of mixed chlorides (simulated waste) but the other reactants varied: (1) Al(OH)3 + NaOH + CS, (2) NaAlO2 + CS, and (3) Al2Si2O7 + NaOH, (CS = colloidal silica). The products were dried, ground, pressed into pellets, fired (650–950 °C), and characterized. Both 5 and 10 mass% of a Si-Na-B glass binder were introduced at different stages in the process. Route (2) proved the most successful at producing high sodalite fractions (up to 100%) with minimal glass binder additions and showed high consolidation potential (up to 91.4% of theoretical density). Detailed comparisons are provided of the results.

  12. Novel Paradigms of Salt and Hypertension.

    PubMed

    Feng, Wenguang; Dell'Italia, Louis J; Sanders, Paul W

    2017-02-20

    Salt resistance/sensitivity refers specifically to the effect of dietary sodium chloride (salt) intake on BP. Increased dietary salt intake promotes an early and uniform expansion of extracellular fluid volume and increased cardiac output. To compensate for these hemodynamic changes and maintain constant BP in salt resistance, renal and peripheral vascular resistance falls and is associated with an increase in production of nitric oxide. In contrast, the decline in peripheral vascular resistance and the increase in nitric oxide are impaired or absent in salt sensitivity, promoting an increase in BP in these individuals. Endothelial dysfunction may pose a particularly significant risk factor in the development of salt sensitivity and subsequent hypertension. Vulnerable salt-sensitive populations may have in common underlying endothelial dysfunction due to genetic or environmental influences. These individuals may be very sensitive to the hemodynamic stress of increased effective blood volume, setting in motion untoward molecular and biochemical events that lead to overproduction of TGF-β, oxidative stress, and limited bioavailable nitric oxide. Finally, chronic high-salt ingestion produces endothelial dysfunction, even in salt-resistant subjects. Thus, the complex syndrome of salt sensitivity may be a function of the endothelium, which is integrally involved in the vascular responses to high salt intake.

  13. Uranium (III) precipitation in molten chloride by wet argon sparging

    NASA Astrophysics Data System (ADS)

    Vigier, Jean-François; Laplace, Annabelle; Renard, Catherine; Miguirditchian, Manuel; Abraham, Francis

    2016-06-01

    In the context of pyrochemical processes for nuclear fuel treatment, the precipitation of uranium (III) in molten salt LiCl-CaCl2 (30-70 mol%) at 705 °C is studied. First, this molten chloride is characterized with the determination of the water dissociation constant. With a value of 10-4.0, the salt has oxoacid properties. Then, the uranium (III) precipitation using wet argon sparging is studied. The salt is prepared using UCl3 precursor. At the end of the precipitation, the salt is totally free of solubilized uranium. The main part is converted into UO2 powder but some uranium is lost during the process due to the volatility of uranium chloride. The main impurity of the resulting powder is calcium. The consequences of oxidative and reductive conditions on precipitation are studied. Finally, coprecipitation of uranium (III) and neodymium (III) is studied, showing a higher sensitivity of uranium (III) than neodymium (III) to precipitation.

  14. Immobilization of IFR salt wastes in mortar

    SciTech Connect

    Fischer, D.F.; Johnson, T.R.

    1988-01-01

    Portland cement-base mortars are being considered for immobilizing chloride salt wastes produced by the fuel cycles of Integral Fast Reactors (IFR). The IFR is a sodium-cooled fast reactor with metal alloy fuels. It has a close-coupled fuel cycle in which fission products are separated from the actinides in an electrochemical cell operating at 500/degree/C. This cell has a liquid cadmium anode in which the fuels are dissolved and a liquid salt electrolyte. The salt will be a mixture of either lithium, potassium, and sodium chlorides or lithium, calcium, barium, and sodium chlorides. One method being considered for immobilizing the treated nontransuranic salt waste is to disperse the salt in a portland cement-base mortar that will be sealed in corrosion-resistant containers. For this application, the grout must be sufficiently fluid that it can be pumped into canister-molds where it will solidify into a strong, leach-resistant material. The set times must be longer than a few hours to allow sufficient time for processing, and the mortar must reach a reasonable compressive strength (/approximately/7 MPa) within three days to permit handling. Because fission product heating will be high, about 0.6 W/kg for a mortar containing 10% waste salt, the effects of elevated temperatures during curing and storage on mortar properties must be considered.

  15. SEPARATION OF PROTACTINIUM FROM MOLTEN SALT REACTOR FUEL COMPOSITIONS

    DOEpatents

    Shaffer, J.H.; Strain, J.E.; Cuneo, D.R.; Kelly, M.J.

    1963-11-12

    A method for selectively precipitating protactinium from a neutron- irradiated fused fluoride salt composition comprising at least one metal fluoride selected from the group consisting of an alkali metal fluoride and an alkaline earth metal fluoride containing dissolved thorium-232 values is presented. An inorganic metal oxide corresponding to any of the metal fluorides of the composition is also added. (AEC)

  16. Effects of Alkali Cations and Halide Anions on the Self-Assembly of Phosphatidylcholine in Oils.

    PubMed

    Lin, Shih-Ting; Lin, Chen-Shin; Chang, Ya-Ying; Whitten, Andrew E; Sokolova, Anna; Wu, Chun-Ming; Ivanov, Viktor A; Khokhlov, Alexei R; Tung, Shih-Huang

    2016-11-22

    The interactions between ions and phospholipids are closely associated with the structures and functions of cell membrane. Instead of conventional aqueous systems, we systematically investigated the effects of inorganic ions on the self-assembly of lecithin, a zwitterionic phosphatidylcholine, in cyclohexane. Previous studies have shown that addition of inorganic salts with specific divalent and trivalent cations can transform lecithin organosols into organogels. In this study, we focused on the effect of monovalent alkali halides. Fourier transform infrared spectroscopy was used to demonstrate that the binding strength of the alkali cations with the phosphate of lecithin is in the order Li(+) > Na(+) > K(+). More importantly, the cation-phosphate interaction is affected by the paired halide anions, and the effect follows the series I(-) > Br(-) > Cl(-). The salts of stronger interactions with lecithin, including LiCl, LiBr, LiI, and NaI, were found to induce cylindrical micelles sufficiently long to form organogels, while others remain organosols. A mechanism based on the charge density of ions and the enthalpy change of the ion exchange between alkali halides and lecithin headgroup is provided to explain the contrasting interactions and the effectiveness of the salts to induce organogelation.

  17. A Trail of Salts

    NASA Technical Reports Server (NTRS)

    2004-01-01

    This graph shows the relative abundances of sulfur (in the form of sulfur tri-oxide) and chlorine at three Meridiani Planum sites: soil measured in the small crater where Opportunity landed; the rock dubbed 'McKittrick' in the outcrop lining the inner edge of the crater; and the rock nicknamed 'Guadalupe,' also in the outcrop. The 'McKittrick' data shown here were taken both before and after the rover finished grinding the rock with its rock abrasion tool to expose fresh rock underneath. The 'Guadalupe' data were taken after the rover grounded the rock. After grinding both rocks, the sulfur abundance rose to high levels, nearly five times higher than that of the soil. This very high sulfur concentration reflects the heavy presence of sulfate salts (approximately 30 percent by weight) in the rocks. Chloride and bromide salts are also indicated. Such high levels of salts strongly suggest the rocks contain evaporite deposits, which form when water evaporates or ice sublimes into the atmosphere.

  18. Microwave evaluation of accelerated chloride ingress in mortar

    NASA Astrophysics Data System (ADS)

    Hu, C.; Case, T.; Castle, M.; Zoughi, R.; Kurtis, K.

    2001-04-01

    Corrosion of steel in reinforced concrete structures can be induced by the presence of chloride ions near the steel/concrete interface. To show the potential of microwave nondestructive testing techniques for evaluating chloride ingress, 8″×8″×8″ mortar specimens with different mixture designs were prepared. To accelerate chloride ingress, they were exposed to cyclical wet/dry conditions, where the wet condition included exposure to salt bath. A complete discussion of the results will be presented in this paper.

  19. Influence of pH, temperature, and concentration on stabilization of aqueous hornet silk solution and fabrication of salt-free materials.

    PubMed

    Kameda, Tsunenori

    2015-01-01

    We found that an aqueous solution of silk from cocoons produced by hornet larvae (hornet silk) can be obtained when the solution is adjusted to basic conditions of pH > 9.2. It is known that native hornet cocoons can be dissolved in concentrated aqueous solution of salts, such as lithium bromide (LiBr) and calcium chloride (CaCl2). Upon the removal of these salts from solution by dialysis, solidification, gelation, or sedimentation of hornet silk is known to occur. In the present study, under basic conditions, however, no such solidification occurred, even after salt removal. In this study, ammonia was used for alkalization of solution because it is volatilized during the casting process and pure hornet silk materials can be obtained after drying. The effects of the concentrations of hornet silk and ammonia, as well as dialysis temperature, on preventing gelation during dialysis were investigated. Dialysis conditions that limit the degradation of hornet silk by hydrolysis in alkali solution were identified. Moreover, casting conditions to prepare flexible and transparent hornet silk film from aqueous ammonia solution were optimized. Molecular structural analysis of hornet silk in aqueous ammonia solution and cast film indicated the formation of α-helix conformations.

  20. Synergistic capture mechanisms for alkali and sulfur species from combustion. Final report

    SciTech Connect

    Peterson, T.W.; Shadman, F.; Wendt, J.O.L.; Mwabe, P.O.

    1994-02-01

    Experimental work was carried out on a 17 kW, 600 cm long, gas laboratory combustor, to investigate the post flame reactive capture of alkali species by kaolinite. Emphasis was on alkali/sorbent interactions occurring in flue gas at temperatures above the alkali dewpoint and on the formation of water insoluble reaction products. Time-temperature studies were carried out by injecting kaolinite at different axial points along the combustor. The effect of chlorine and sulfur on alkali capture was investigated by doping the flame with SO{sub 2} and Cl{sub 2} gases to simulate coal flame environments. Particle time and temperature history was kept as close as possible to that which would ordinarily be found in a practical boiler. Experiments designed to extract apparent initial reaction rates were carried using a narrow range, 1-2 {mu}m modal size sorbent, while, a coarse, multi size sorbent was used to investigate the governing transport mechanisms. The capture reaction has been proposed to be between alkali hydroxide and activated kaolinite, and remains so in the presence of sulfur and chlorine. The presence of sulfur reduces sodium capture by under 10% at 1300{degree}C. Larger reductions at lower temperatures are attributed to the elevated dewpoint of sodium ({approximately}850{degree}C) with subsequent reduction in sorbent residence time in the alkali gas phase domain. Chlorine reduces sodium capture by 30% across the temperature range covered by the present experiments. This result has been linked to thermodynamic equilibria between sodium hydroxide, sodium chloride and water.

  1. Interpretation of postmortem vitreous concentrations of sodium and chloride.

    PubMed

    Zilg, B; Alkass, K; Berg, S; Druid, H

    2016-06-01

    Vitreous fluid can be used to analyze sodium and chloride levels in deceased persons, but it remains unclear to what extent such results can be used to diagnose antemortem sodium or chloride imbalances. In this study we present vitreous sodium and chloride levels from more than 3000 cases. We show that vitreous sodium and chloride levels both decrease with approximately 2.2mmol/L per day after death. Since potassium is a well-established marker for postmortem interval (PMI) and easily can be analyzed along with sodium and chloride, we have correlated sodium and chloride levels with the potassium levels and present postmortem reference ranges relative the potassium levels. We found that virtually all cases outside the reference range show signs of antemortem hypo- or hypernatremia. Vitreous sodium or chloride levels can be the only means to diagnose cases of water or salt intoxication, beer potomania or dehydration. We further show that postmortem vitreous sodium and chloride strongly correlate and in practice can be used interchangeably if analysis of one of the ions fails. It has been suggested that vitreous sodium and chloride levels can be used to diagnose drowning or to distinguish saltwater from freshwater drowning. Our results show that in cases of freshwater drowning, vitreous sodium levels are decreased, but that this mainly is an effect of postmortem diffusion between the eye and surrounding water rather than due to the drowning process, since the decrease in sodium levels correlates with immersion time.

  2. [Gustatory sensitivity to sodium chloride and potassium chloride and certain parameters of sodium metabolism in patients with bronchial asthma].

    PubMed

    Mineev, V N; Suparnovich, I Iu

    2008-01-01

    The aim of the study was to determine threshold gustatory sensitivity (TGS) to sodium chloride and potassium chloride in patients with bronchial asthma (BA) taking into account a number of factors responsible for the enhanced risk of development and progress of this disease. Forty five practically healthy subjects were compared with 139 asthmatic patients; a separate group comprised patients treated permanently with oral glucocorticoids and those having non-pulmonary allergy. Chemically pure solutions of sodium and potassium chlorides were used in the dripping test to assess TGS. Asthmatic patients had enhanced TGS to sodium chloride compared with healthy subjects. TGS values were especially high in non-allergic bronchial asthma and minimal in allergic asthma when they were unrelated to the phase of the disease. TGS to potassium chloride in asthmatic patients also differed from that in healthy subjects; more patients were bitter-insensitive or sensitive only to high concentrations of potassium chloride. Patients treated with systemic glucocorticoids had the highest TGS to sodium chloride. Patients with non-pulmonary allergy and allergic BA had very similar TGS to potassium chloride. TGS to sodium chloride in the former was lower than in healthy subjects and patients with allergic BA. Asthmatic patients had a higher sodium ion concentration in erythrocytes than normal subjects; it reached maximum values in persons used to add salt to fully cooked food.

  3. Nitrite toxicity of Litopenaeus vannamei in water containing low concentrations of sea salt or mixed salts

    USGS Publications Warehouse

    Sowers, A.; Young, S.P.; Isely, J.J.; Browdy, C.L.; Tomasso, J.R.

    2004-01-01

    The uptake, depuration and toxicity of environmental nitrite was characterized in Litopenaeus vannamei exposed in water containing low concentrations of artificial sea salt or mixed salts. In 2 g/L artificial sea salts, nitrite was concentrated in the hemolymph in a dose-dependent and rapid manner (steady-state in about 2 d). When exposed to nitrite in 2 g/L artificial sea salts for 4 d and then moved to a similar environment without added nitrite, complete depuration occurred within a day. Increasing salinity up to 10 g/L decreased uptake of environmental nitrite. Nitrite uptake in environments containing 2 g/L mixed salts (combination of sodium, potassium, calcium and magnesium chlorides) was similar to or lower than rates in 2 g/L artificial sea salt. Toxicity was inversely related to total dissolved salt and chloride concentrations and was highest in 2 g/L artificial sea salt (96-h medial lethal concentration = 8.4 mg/L nitrite-N). Animals that molted during the experiments did not appear to be more susceptible to nitrite than animals that did not molt. The shallow slope of the curve describing the relationship between toxicity and salinity suggests that management of nitrite toxicity in low-salinity shrimp ponds by addition of more salts may not be practical. ?? Copyright by the World Aquaculture Society 2004.

  4. Measurement of alkali in PFBC exhaust

    SciTech Connect

    Schmalzer, D.K.; Steindler, M.J.; Lee, S.H.D.; Swift, W.M.

    1992-12-01

    This project supports the DOE/METC Fossil Energy Program for the development of Pressurized fluidized bed combustion (PFBC) technology. Based on the analytical activated-bauxite sorber-bed technique, we are developing the RABSAM as an alternative to the on-line alkali analyzer for field application. RABSAM is a sampling probe containing a regenerable activated-bauxite adsorbent (RABA). It can be inserted directly into the PFBC exhaust duct and requires no high temperature/high pressure (HTHP) sampling line. Alkali vapors are captured by the adsorbent purely through physical adsorption. The adsorbent is regenerated by a simple water-reaching process, which also recovers the adsorbed alkalis. The alkali analysis of the leachate by atomic absorption (AA) provides a basis for calculating the time-averaged alkali-vapor concentration in the PFBC exhaust. If the RABA is to use commercial-grade activated bauxite, the clay impurities in activated bauxite can react with alkali vapors and, therefore, need to be either removed or deactivated. In earlier work, a 6{und M}-LiCl-solution impregnation technique was shown to deactivate these impurities in fresh activated bauxite. During this year, RABA prepared by this technique was tested in a pressurized alkali-vapor sorption test unit to determine its NaCl-vapor capture efficiency and the regenerability of the sorbent by water extraction. Results of this study are presented and discussed in the following.

  5. Measurement of alkali in PFBC exhaust

    SciTech Connect

    Schmalzer, D.K.; Steindler, M.J.; Lee, S.H.D.; Swift, W.M.

    1992-01-01

    This project supports the DOE/METC Fossil Energy Program for the development of Pressurized fluidized bed combustion (PFBC) technology. Based on the analytical activated-bauxite sorber-bed technique, we are developing the RABSAM as an alternative to the on-line alkali analyzer for field application. RABSAM is a sampling probe containing a regenerable activated-bauxite adsorbent (RABA). It can be inserted directly into the PFBC exhaust duct and requires no high temperature/high pressure (HTHP) sampling line. Alkali vapors are captured by the adsorbent purely through physical adsorption. The adsorbent is regenerated by a simple water-reaching process, which also recovers the adsorbed alkalis. The alkali analysis of the leachate by atomic absorption (AA) provides a basis for calculating the time-averaged alkali-vapor concentration in the PFBC exhaust. If the RABA is to use commercial-grade activated bauxite, the clay impurities in activated bauxite can react with alkali vapors and, therefore, need to be either removed or deactivated. In earlier work, a 6[und M]-LiCl-solution impregnation technique was shown to deactivate these impurities in fresh activated bauxite. During this year, RABA prepared by this technique was tested in a pressurized alkali-vapor sorption test unit to determine its NaCl-vapor capture efficiency and the regenerability of the sorbent by water extraction. Results of this study are presented and discussed in the following.

  6. Measurement of alkali in PFBC exhaust

    SciTech Connect

    Lee, S.H.D.; Swift, W.M.

    1992-01-01

    This project supports the DOE/METC Fossil Energy Program for the development of PFBC technology. Based on the analytical activated-bauxite sorber-bed technique, we are developing the RABSAM as an altemative to the on-line alkali analyzer for field application. As shown in Fig. 1, the RABSAM is a sampling probe containing a regenerable activated-bauxite adsorbent (RABA). It can be inserted directly into the PFBC exhaust duct and requires no HTHP sampling line. Alkali vapors are captured by the adsorbent purely through physical adsorption. The adsorbent is regenerated by a simple water-leaching process, which also recovers the adsorbed alkalis. The alkali analysis of the leachate by atomic absorption (AA) provides a basis for calculating the time-averaged alkali-vapor concentration in the PFBC exhaust. If the RABA is to use commercial grade activated bauxite, the clay impurities in activated bauxite can react with alkali vapors and, therefore, need to be either removed or deactivated. In earlier work, a 6M-LiCl-solution impregnation technique was shown to deactivate these impurities in fresh activated bauxite [8]. During this year, RABA prepared by this technique was tested in a pressurized alkali-vapor sorption test unit to determine its NaCl-vapor capture efficiency and the regenerability of the sorbent by water extraction. Results of this study are presented and discussed.

  7. Measurement of alkali in PFBC exhaust

    SciTech Connect

    Lee, S.H.D.; Swift, W.M.

    1992-11-01

    This project supports the DOE/METC Fossil Energy Program for the development of PFBC technology. Based on the analytical activated-bauxite sorber-bed technique, we are developing the RABSAM as an altemative to the on-line alkali analyzer for field application. As shown in Fig. 1, the RABSAM is a sampling probe containing a regenerable activated-bauxite adsorbent (RABA). It can be inserted directly into the PFBC exhaust duct and requires no HTHP sampling line. Alkali vapors are captured by the adsorbent purely through physical adsorption. The adsorbent is regenerated by a simple water-leaching process, which also recovers the adsorbed alkalis. The alkali analysis of the leachate by atomic absorption (AA) provides a basis for calculating the time-averaged alkali-vapor concentration in the PFBC exhaust. If the RABA is to use commercial grade activated bauxite, the clay impurities in activated bauxite can react with alkali vapors and, therefore, need to be either removed or deactivated. In earlier work, a 6M-LiCl-solution impregnation technique was shown to deactivate these impurities in fresh activated bauxite [8]. During this year, RABA prepared by this technique was tested in a pressurized alkali-vapor sorption test unit to determine its NaCl-vapor capture efficiency and the regenerability of the sorbent by water extraction. Results of this study are presented and discussed.

  8. Phosphate salts

    MedlinePlus

    ... sodium if you have heart disease. Fluid retention (edema): Avoid using phosphate salts that contain sodium if ... heart failure, or other conditions that can cause edema. High levels of calcium in the blood (hypercalcemia): ...

  9. Bath Salts

    MedlinePlus

    ... panic attacks depression suicidal thoughts paranoia delusions and hallucinations distorted sense of reality decreased ability to think ... of bath salts may cause people to have hallucinations, hear voices, feel paranoid, and develop a psychosis ...

  10. Pretreatment of corn stover by combining ionic liquid dissolution with alkali extraction.

    PubMed

    Geng, Xinglian; Henderson, Wesley A

    2012-01-01

    Pretreatment plays an important role in the efficient enzymatic hydrolysis of biomass into fermentable sugars for biofuels. A highly effective pretreatment method is reported for corn stover which combines mild alkali-extraction followed by ionic liquid (IL) dissolution of the polysaccharides and regeneration (recovery of the polysaccharides as solids). Air-dried, knife-milled corn stover was soaked in 1% NaOH at a moderate condition (90°C, 1 h) and then thoroughly washed with hot deionized (DI) water. The alkali extraction solublized 75% of the lignin and 37% of the hemicellulose. The corn stover fibers became softer and smoother after the alkali extraction. Unextracted and extracted corn stover samples were separately dissolved in an IL, 1-butyl-3-methylimidazolium chloride (C(4) mimCl), at 130°C for 2 h and then regenerated with DI water. The IL dissolution process did not significantly change the chemical composition of the materials, but did alter their structural features. Untreated and treated corn stover samples were hydrolyzed with commercial enzyme preparations including cellulases and hemicellulases at 50°C. The glucose yield from the corn stover sample that was both alkali-extracted and IL-dissolved was 96% in 5 h of hydrolysis. This is a highly effective methodology for minimizing the enzymatic loading for biomass hydrolysis and/or maximizing the conversion of biomass polysaccharides into sugars.

  11. Diode pumped alkali vapor fiber laser

    DOEpatents

    Payne, Stephen A.; Beach, Raymond J.; Dawson, Jay W.; Krupke, William F.

    2006-07-26

    A method and apparatus is provided for producing near-diffraction-limited laser light, or amplifying near-diffraction-limited light, in diode pumped alkali vapor photonic-band-gap fiber lasers or amplifiers. Laser light is both substantially generated and propagated in an alkali gas instead of a solid, allowing the nonlinear and damage limitations of conventional solid core fibers to be circumvented. Alkali vapor is introduced into the center hole of a photonic-band-gap fiber, which can then be pumped with light from a pump laser and operated as an oscillator with a seed beam, or can be configured as an amplifier.

  12. Diode pumped alkali vapor fiber laser

    DOEpatents

    Payne, Stephen A.; Beach, Raymond J.; Dawson, Jay W.; Krupke, William F.

    2007-10-23

    A method and apparatus is provided for producing near-diffraction-limited laser light, or amplifying near-diffraction-limited light, in diode pumped alkali vapor photonic-band-gap fiber lasers or amplifiers. Laser light is both substantially generated and propagated in an alkali gas instead of a solid, allowing the nonlinear and damage limitations of conventional solid core fibers to be circumvented. Alkali vapor is introduced into the center hole of a photonic-band-gap fiber, which can then be pumped with light from a pump laser and operated as an oscillator with a seed beam, or can be configured as an amplifier.

  13. Advancements in flowing diode pumped alkali lasers

    NASA Astrophysics Data System (ADS)

    Pitz, Greg A.; Stalnaker, Donald M.; Guild, Eric M.; Oliker, Benjamin Q.; Moran, Paul J.; Townsend, Steven W.; Hostutler, David A.

    2016-03-01

    Multiple variants of the Diode Pumped Alkali Laser (DPAL) have recently been demonstrated at the Air Force Research Laboratory (AFRL). Highlights of this ongoing research effort include: a) a 571W rubidium (Rb) based Master Oscillator Power Amplifier (MOPA) with a gain (2α) of 0.48 cm-1, b) a rubidium-cesium (Cs) Multi-Alkali Multi-Line (MAML) laser that simultaneously lases at both 795 nm and 895 nm, and c) a 1.5 kW resonantly pumped potassium (K) DPAL with a slope efficiency of 50%. The common factor among these experiments is the use of a flowing alkali test bed.

  14. Alternative Waste Forms for Electro-Chemical Salt Waste

    SciTech Connect

    Crum, Jarrod V.; Sundaram, S. K.; Riley, Brian J.; Matyas, Josef; Arreguin, Shelly A.; Vienna, John D.

    2009-10-28

    This study was undertaken to examine alternate crystalline (ceramic/mineral) and glass waste forms for immobilizing spent salt from the Advanced Fuel Cycle Initiative (AFCI) electrochemical separations process. The AFCI is a program sponsored by U.S. Department of Energy (DOE) to develop and demonstrate a process for recycling spent nuclear fuel (SNF). The electrochemical process is a molten salt process for the reprocessing of spent nuclear fuel in an electrorefiner and generates spent salt that is contaminated with alkali, alkaline earths, and lanthanide fission products (FP) that must either be cleaned of fission products or eventually replaced with new salt to maintain separations efficiency. Currently, these spent salts are mixed with zeolite to form sodalite in a glass-bonded waste form. The focus of this study was to investigate alternate waste forms to immobilize spent salt. On a mole basis, the spent salt is dominated by alkali and Cl with minor amounts of alkaline earth and lanthanides. In the study reported here, we made an effort to explore glass systems that are more compatible with Cl and have not been previously considered for use as waste forms. In addition, alternate methods were explored with the hope of finding a way to produce a sodalite that is more accepting of as many FP present in the spent salt as possible. This study was done to investigate two different options: (1) alternate glass families that incorporate increased concentrations of Cl; and (2) alternate methods to produce a mineral waste form.

  15. Gel nanostructure in alkali-activated binders based on slag and fly ash, and effects of accelerated carbonation

    SciTech Connect

    Bernal, Susan A.; Provis, John L.; Walkley, Brant; San Nicolas, Rackel; Gehman, John D.; Brice, David G.; Kilcullen, Adam R.; Duxson, Peter; Deventer, Jannie S.J. van

    2013-11-15

    Binders formed through alkali-activation of slags and fly ashes, including ‘fly ash geopolymers’, provide appealing properties as binders for low-emissions concrete production. However, the changes in pH and pore solution chemistry induced during accelerated carbonation testing provide unrealistically low predictions of in-service carbonation resistance. The aluminosilicate gel remaining in an alkali-activated slag system after accelerated carbonation is highly polymerised, consistent with a decalcification mechanism, while fly ash-based binders mainly carbonate through precipitation of alkali salts (bicarbonates at elevated CO{sub 2} concentrations, or carbonates under natural exposure) from the pore solution, with little change in the binder gel identifiable by nuclear magnetic resonance spectroscopy. In activated fly ash/slag blends, two distinct gels (C–A–S–H and N–A–S–H) are formed; under accelerated carbonation, the N–A–S–H gel behaves comparably to fly ash-based systems, while the C–A–S–H gel is decalcified similarly to alkali-activated slag. This provides new scope for durability optimisation, and for developing appropriate testing methodologies. -- Highlights: •C-A-S-H gel in alkali-activated slag decalcifies during accelerated carbonation. •Alkali-activated fly ash gel changes much less under CO{sub 2} exposure. •Blended slag-fly ash binder contains two coexisting gel types. •These two gels respond differently to carbonation. •Understanding of carbonation mechanisms is essential in developing test methods.

  16. Full-scale treatment of wastewater from a biodiesel fuel production plant with alkali-catalyzed transesterification.

    PubMed

    De Gisi, Sabino; Galasso, Maurizio; De Feo, Giovanni

    2013-01-01

    The treatment of wastewater derived from a biodiesel fuel (BDF) production plant with alkali-catalyzed transesterification was studied at full scale. The investigated wastewater treatment plant consisted of the following phases: primary adsorption/coagulation/flocculation/sedimentation processes, biological treatment with the combination of trickling filter and activated sludge systems, secondary flocculation/sedimentation processes, and reverse osmosis (RO) system with spiral membranes. All the processes were developed in a continuous mode, while the RO experiment was performed with batch tests. Two types of BDF wastewater were considered: the first wastewater (WW1) had an average total chemical oxygen demand (COD), pH and feed flow rate of 10,850.8 mg/L, 5.9 and 2946.7 L/h, respectively, while the second wastewater (WW2) had an average total COD, pH and feed flow rate of 43,898.9 mg/L, 3.3 and 2884.6 L/h, respectively. The obtained results from the continuous tests showed a COD removal percentage of more than 90% for the two types of wastewater considered. The removal of biorefractory COD and salts was obtained with a membrane technology in order to reuse the RO permeate in the factory production cycle. The rejections percentage of soluble COD, chlorides and sulphates were 92.8%, 95.0% and 99.5%, respectively. Because the spiral membranes required a high number of washing cycles, the use of plane membranes was preferable. Finally, the RO reject material should be evaporated using the large amount of inexpensive heat present in this type of industry.

  17. [Food processing industry--the salt shock to the consumers].

    PubMed

    Doko Jelinić, Jagoda; Nola, Iskra Alexandra; Andabaka, Damir

    2010-05-01

    Industrial food production and processing is necessarily connected with the use of salt. Salt or sodium chloride is used as a preservative, spice, agent for color maintenance, texture, and to regulate fermentation by stopping the growth of bacteria, yeast and mold. Besides kitchen salt, other types of salt that also contain sodium are used in various technological processes in food preparing industry. Most of the "hidden" salt, 70%-75%, can be brought to the body by using industrial food, which, unfortunately, has been increasingly used due to the modern way of life. Bread and bakery products, meat products, various sauces, dried fish, various types of cheese, fast food, conserved vegetables, ready-made soups and food additives are the most common industrial foods rich in sodium. Many actions have been taken all over the world to restrict salt consumption. The World Health Organization recommends the upper limit of salt input of 5 g per day. These actions appeal to food industry to reduce the proportion of salt in their products. Besides lower salt addition during manufacture, food industry can use salt substitutes, in particular potassium chloride (KCl), in combination with additives that can mask the absence of salt, and flavor intensifiers that also enhance the product salinity. However, food industry is still quite resistant to reducing salt in their products for fear from losing profits.

  18. Oxidation of hydrogen halides to elemental halogens with catalytic molten salt mixtures

    DOEpatents

    Rohrmann, Charles A.

    1978-01-01

    A process for oxidizing hydrogen halides by means of a catalytically active molten salt is disclosed. The subject hydrogen halide is contacted with a molten salt containing an oxygen compound of vanadium and alkali metal sulfates and pyrosulfates to produce an effluent gas stream rich in the elemental halogen. The reduced vanadium which remains after this contacting is regenerated to the active higher valence state by contacting the spent molten salt with a stream of oxygen-bearing gas.

  19. Measurement of alkali vapors in PFBC flue gas and their removal with a fixed granular-bed sorber, October 1, 1985-September 30, 1986

    SciTech Connect

    Lee, S.H.D.; Myles, K.M.

    1986-01-01

    Alkali-metal compounds, such as chlorides and sulfates of sodium and potassium, present in the flue gas of coal combustion could cause hot corrosion of a gas turbine. The current industrial gas-turbine specification limit for alkali-metal compounds in the combustion gas entering a turbine is equivalent to 0.024 ppmW. Spacil and Luthra predict that the quantity of alkali vapor in the flue gas from PFBC could be up to two orders of magnitude greater than this allowable level. In contrast, the recent calculations by Scandrett and Clift suggest that, if the aerosol alkali particulate could be removed, the residual alkali vapor in the flue gas would be less than the limit. Measurements of the alkali vapor in PFBC flue gas have been made by several institutions. The measured alkali vapor concentration in the flue gas is in the order of 0.1 to 10 ppmW. Normally, a conventional batch-type extraction of the flue gas, followed by the analysis of the condensate, has been used in these measurements. It was not until recently that a real-time, on-line alkali analyzer was developed and tested in the gas stream of both coal gasification and combustion. A fixed granular-bed sorber is being developed at Argonne National Laboratory (ANL) for the control of the alkali vapor in PFBC flue gas. After an extensive screening study, activated bauxite was found to be the most effective sorbent in capturing the NaCl, KCl, and K/sub 2/SO/sub 4/ vapors that were doped into a simulated PFBC flue gas. Activated bauxite was also demonstrated to be easily and effectively regenerated for reuse by a simple water-leaching process. A capture efficiency of greater than 99.8% CaCl vapor has been achieved. The effectiveness of activated bauxite for alkali-vapor capture has been confirmed by others. 21 refs., 12 figs., 5 tabs.

  20. Alkali metal for ultraviolet band-pass filter

    NASA Technical Reports Server (NTRS)

    Mardesich, Nick (Inventor); Fraschetti, George A. (Inventor); Mccann, Timothy A. (Inventor); Mayall, Sherwood D. (Inventor); Dunn, Donald E. (Inventor); Trauger, John T. (Inventor)

    1993-01-01

    An alkali metal filter having a layer of metallic bismuth deposited onto the alkali metal is provided. The metallic bismuth acts to stabilize the surface of the alkali metal to prevent substantial surface migration from occurring on the alkali metal, which may degrade optical characteristics of the filter. To this end, a layer of metallic bismuth is deposited by vapor deposition over the alkali metal to a depth of approximately 5 to 10 A. A complete alkali metal filter is described along with a method for fabricating the alkali metal filter.

  1. Chloride, bromide and iodide scintillators with europium

    DOEpatents

    Zhuravleva, Mariya; Yang, Kan

    2016-09-27

    A halide scintillator material is disclosed where the halide may comprise chloride, bromide or iodide. The material is single-crystalline and has a composition of the general formula ABX.sub.3 where A is an alkali, B is an alkali earth and X is a halide which general composition was investigated. In particular, crystals of the formula ACa.sub.1-yEu.sub.yI.sub.3 where A=K, Rb and Cs were formed as well as crystals of the formula CsA.sub.1-yEu.sub.yX.sub.3 (where A=Ca, Sr, Ba, or a combination thereof and X=Cl, Br or I or a combination thereof) with divalent Europium doping where 0.ltoreq.y.ltoreq.1, and more particularly Eu doping has been studied at one to ten mol %. The disclosed scintillator materials are suitable for making scintillation detectors used in applications such as medical imaging and homeland security.

  2. Phosphonium chloride for thermal storage

    NASA Technical Reports Server (NTRS)

    Sutton, J. G.; Heimlich, P. F.; Tepper, E. H.

    1972-01-01

    Development of systems for storage of thermal energy is discussed. Application of phosphonium chloride for heat storage through reversible dissociation is described. Chemical, physical, and thermodynamic properties of phosphonium chloride are analyzed and dangers in using phosphonium chloride are explained.

  3. FTIR study of matrix-isolated halides of dysprosium and thulium and their gaseous heterocomplexes with alkali halides

    SciTech Connect

    Feltrin, A.; Cesaro, S.N.

    1996-06-01

    Vibrational spectra of dysprosium and thulium chlorides, bromides, and iodides isolated in argon have been studied for the first time. The appearance of a single band, even in heavy deposits, suggested a planar geometry for all the samples examined. The complexity of Dy and Tm chlorides spectra, partly because of isotopic patterns, required a reinvestigation of NdCl{sub 3} isolated in argon and have been explained by comparison. Vapors in equilibrium over heated equimolar mixtures of a number of Dy, Tm, and Nd halides with alkali halides trapped in argon have been also investigated. FTIR measurements gave experimental evidence for the formation of gaseous heterocomplexes whose geometry is discussed.

  4. Post-Harvest Processing Methods for Reduction of Silica and Alkali Metals in Wheat Straw

    SciTech Connect

    Thompson, David Neal; Lacey, Jeffrey Alan; Shaw, Peter Gordon

    2002-04-01

    Silica and alkali metals in wheat straw limit its use for bioenergy and gasification. Slag deposits occur via the eutectic melting of SiO2 with K2O, trapping chlorides at surfaces and causing corrosion. A minimum melting point of 950°C is desirable, corresponding to SiO2:K2O of about 3:1. Mild chemical treatments were used to reduce Si, K, and Cl, while varying temperature, concentration, %-solids, and time. Dilute acid was more effective at removing K and Cl, while dilute alkali was more effective for Si. Reduction of minerals in this manner may prove economical for increasing utilization of the straw for combustion or gasification.

  5. Effects of the order of addition of reagents and alkali on modification of wheat starches.

    PubMed

    Sui, Zhongquan; Huber, Kerry C; BeMiller, James N

    2015-07-10

    The objective of this research was to determine if adding reactive reagents to wheat starch granules before addition of alkali (the TRF method) would produce products that are different than those obtained with the conventional procedure (adding alkali before addition of reagent). Laboratory-isolated (LI) and commercial (C) normal (NWS) and waxy (WWS) wheat starches were each reacted with 6 reagents (acetic-adipic mixed anhydride (AAMA), phosphoryl chloride (POCl3), sodium trimetaphosphate (STMP), acetic anhydride (AA), succinic anhydride (SA), octenylsuccinic anhydride (OSA)). Data obtained were similar to those previously obtained with maize starches (Sui, Huber, & BeMiller, 2013). Almost no starch polymer molecule modification occurred when the TRF method and AAMA or AA were used; less than a third as much reaction when SA was the reagent used, and about the same amount of reaction when POCl3, STMP, or OSA were the reagents used (for different reasons).

  6. Post-harvest processing methods for reduction of silica and alkali metals in wheat straw.

    PubMed

    Thompson, David N; Shaw, Peter G; Lacey, Jeffrey A

    2003-01-01

    Silica and alkali metals in wheat straw limit its use for bioenergy and gasification. Slag deposits occur via the eutectic melting of SiO2 with K2O, trapping chlorides at surfaces and causing corrosion. A minimum melting point of 950 degrees C is desirable, corresponding to an SiO2:K2O weight ratio of about 3:1. Mild chemical treatments were used to reduce Si, K, and Cl, while varying temperature, concentration, % solids, and time. Dilute acid was more effective at removing K and Cl, while dilute alkali was more effective for Si. Reduction of minerals in this manner may prove economical for increasing utilization of the straw for combustion or gasification.

  7. Cavitation luminescence of argon-saturated alkali-metal solutions from a conical bubble

    NASA Astrophysics Data System (ADS)

    Jing, Ha; Jie He, Shou; Fang, Wang; Min, Song Jian

    2008-10-01

    In 1,2-propanediol solutions containing sodium chloride, spectra of luminescence from a collapsed conical bubble have been detected. Results show that the spectra consist of a broad continuum background, on which a resonance line arising from de-excitation of sodium atom at 589 nm and two satellite diffuse bands at ~554 nm and 620 nm respectively are superimposed. These are confirmed to be the emission from alkali-metal-argon exciplexes and are suggested to occur when the mixtures of alkali metal vapour and argon are rapidly compressed. The intracavity density of argon deduced from the line shift of Na resonance line data is estimated to be about 2 × 1026 m-3.

  8. Improved alkali-metal/silicate binders

    NASA Technical Reports Server (NTRS)

    Schutt, J.

    1978-01-01

    Family of inorganic binders utilizes potassium or sodium oxide/silicate dispersion and employs high mole ratio of silicon dioxide to alkali-metal binder. Binders are stable, inexpensive, extremely water resistant, and easy to apply.

  9. Alkali Metal Handling Practices at NASA MSFC

    NASA Technical Reports Server (NTRS)

    Salvail, Patrick G.; Carter, Robert R.

    2002-01-01

    NASA Marshall Space Flight Center (MSFC) is NASA s principle propulsion development center. Research and development is coordinated and carried out on not only the existing transportation systems, but also those that may be flown in the near future. Heat pipe cooled fast fission cores are among several concepts being considered for the Nuclear Systems Initiative. Marshall Space Flight Center has developed a capability to handle high-purity alkali metals for use in heat pipes or liquid metal heat transfer loops. This capability is a low budget prototype of an alkali metal handling system that would allow the production of flight qualified heat pipe modules or alkali metal loops. The processing approach used to introduce pure alkali metal into heat pipe modules and other test articles are described in this paper.

  10. Alkali metal propellants for MPD thrusters

    NASA Technical Reports Server (NTRS)

    Polk, J. E.; Pivirotto, T. J.

    1991-01-01

    Experiments performed in the United States in the 1960s and early 1970s and in the Soviet Union with alkali metal-fuelled MPD thrusters indicate performance levels substantially better than those achieved with gaseous propellants. Cathode wear appears to be less in engines with alkali metal propellants also. A critical review of the available data indicates that the data are consistent and reliable. An analysis of testing and systems-level considerations shows that pumping requirements for testing are substantially decreased and reductions in tankage fraction can be expected. In addition, while care must be exercised in handling the alkali metals, it is not prohibitively difficult or hazardous. The greatest disadvantage seems to be the potential for spacecraft contamination, but there appear to be viable strategies for minimizing the impact of propellant deposition on spacecraft surfaces. Renewed examination of alkali metal-fuelled MPD thrusters for ambitious SEI missions is recommended.

  11. REMOVAL OF CHLORIDE FROM ACIDIC SOLUTIONS USING NO2

    SciTech Connect

    Visser, A; Robert Pierce, R; James Laurinat, J

    2006-08-22

    Chloride (Cl{sup -}) salt processing in strong acids is used to recycle plutonium (Pu) from pyrochemical residues. The Savannah River National Laboratory (SRNL) is studying the potential application of nitrogen dioxide (NO{sub 2}) gas to effectively convert dissolved pyrochemical salt solutions to chloride-free solutions and improve recovery operations. An NO{sub 2} sparge has been shown to effectively remove Cl{sup -} from solutions containing 6-8 M acid (H{sup +}) and up to 5 M Cl{sup -}. Chloride removal occurs as a result of the competition of at least two reactions, one which is acid-dependent. Below 4 M H+, NO2 reacts with Cl- to produce nitrosyl chloride (ClNO). Between 6 M and 8 M H{sup +}, the reaction of hydrochloric acid (HCl) with nitric acid (HNO{sub 3}), facilitated by the presence of NO{sub 2}, strongly affects the rate of Cl{sup -} removal. The effect of heating the acidic Cl{sup -} salt solution without pre-heating the NO{sub 2} gas has minimal effect on Cl{sup -} removal rates when the contact times between NO{sub 2} and the salt solution are on the order of seconds.

  12. Desulfurizing Coal With an Alkali Treatment

    NASA Technical Reports Server (NTRS)

    Ravindram, M.; Kalvinskas, J. J.

    1987-01-01

    Experimental coal-desulfurization process uses alkalies and steam in fluidized-bed reactor. With highly volatile, high-sulfur bituminous coal, process removed 98 percent of pyritic sulfur and 47 percent of organic sulfur. Used in coal liquefaction and in production of clean solid fuels and synthetic liquid fuels. Nitrogen or steam flows through bed of coal in reactor. Alkalies react with sulfur, removing it from coal. Nitrogen flow fluidizes bed while heating or cooling; steam is fluidizing medium during reaction.

  13. 21 CFR 201.306 - Potassium salt preparations intended for oral ingestion by man.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Potassium salt preparations intended for oral... Drug Products § 201.306 Potassium salt preparations intended for oral ingestion by man. (a) The Food... coated tablets containing potassium chloride or other potassium salts which supply 100 milligrams or...

  14. 40 CFR 415.470 - Applicability; description of the nickel salts production subcategory.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... nickel salts production subcategory. 415.470 Section 415.470 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Nickel Salts Production Subcategory § 415.470 Applicability; description of the nickel... nickel salts, including (a) nickel sulfate, nickel chloride, nickel nitrate, and nickel fluoborate,...

  15. 40 CFR 415.470 - Applicability; description of the nickel salts production subcategory.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... nickel salts production subcategory. 415.470 Section 415.470 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Nickel Salts Production Subcategory § 415.470 Applicability; description of the nickel... nickel salts, including (a) nickel sulfate, nickel chloride, nickel nitrate, and nickel fluoborate,...

  16. 40 CFR 415.470 - Applicability; description of the nickel salts production subcategory.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... nickel salts production subcategory. 415.470 Section 415.470 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Nickel Salts Production Subcategory § 415.470 Applicability; description of the nickel... nickel salts, including (a) nickel sulfate, nickel chloride, nickel nitrate, and nickel fluoborate,...

  17. 40 CFR 415.470 - Applicability; description of the nickel salts production subcategory.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... nickel salts production subcategory. 415.470 Section 415.470 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Nickel Salts Production Subcategory § 415.470 Applicability; description of the nickel... nickel salts, including (a) nickel sulfate, nickel chloride, nickel nitrate, and nickel fluoborate,...

  18. 21 CFR 201.306 - Potassium salt preparations intended for oral ingestion by man.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 4 2013-04-01 2013-04-01 false Potassium salt preparations intended for oral... Drug Products § 201.306 Potassium salt preparations intended for oral ingestion by man. (a) The Food... coated tablets containing potassium chloride or other potassium salts which supply 100 milligrams or...

  19. 21 CFR 201.306 - Potassium salt preparations intended for oral ingestion by man.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 4 2014-04-01 2014-04-01 false Potassium salt preparations intended for oral... Drug Products § 201.306 Potassium salt preparations intended for oral ingestion by man. (a) The Food... coated tablets containing potassium chloride or other potassium salts which supply 100 milligrams or...

  20. 21 CFR 201.306 - Potassium salt preparations intended for oral ingestion by man.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 4 2012-04-01 2012-04-01 false Potassium salt preparations intended for oral... Drug Products § 201.306 Potassium salt preparations intended for oral ingestion by man. (a) The Food... coated tablets containing potassium chloride or other potassium salts which supply 100 milligrams or...