Linear alkylbenzene sulfonates (LAS) in sewage sludges, soils and sediments: analytical determination and environmental safety considerations.

PubMed

De Henau, H; Mathijs, E; Hopping, W D

1986-01-01

Linear Alkylbenzenesulphonates (LAS), a major anionic surfactant used in laundry products, can be measured specifically in the environment by instrumental analysis. In addition to a desulphonation-gas chromatography approach, a method based on high performance liquid chromatography has been developed. The main features of the methods are outlined, and LAS concentrations measured in sewage sludge, sediments and sludge amended soils are reported. Knowledge of usage volumes, sewage treatment practices and environmental transport and transformation mechanisms has been used to predict concentrations of LAS. These calculated concentrations were found to agree well with those actually measured in the environment. Both measured and calculated ambient concentrations of LAS are below those which could produce potentially adverse effects in representative surface water, benthic and terrestrial organisms.

Effects of a surfactant (FFD-6) on Scenedesmus morphology and growth under different nutrient conditions.

PubMed

Lürling, M

2006-03-01

Surfactants are man-made compounds that are meanwhile omnipresent in the environment, but environmental concentrations of surfactants are such that they are thought to have little risk for aquatic systems. The major anionic surfactants currently on the global market are linear alkylbenzene sulfonates (LAS), a class where the commercially available FFD-6 belongs to. The hypothesis was tested that sublethal effects of FFD-6, i.e. the morphological effect of colony formation in the common test alga Scenedesmus obliquus, occurs at a concentration lower than the no-observed-effect concentrations for endpoints commonly used in regulatory toxicity testing with algae. The surfactant FFD-6 induced colonies in Scenedesmus at concentrations a few orders of magnitude lower (i.e. between 0.001 and 0.01 g l-1) than at which growth inhibition was observed (i.e. between 1 and 10g l -1). Growth rates were lowest for Scenedesmus grown in P-limited medium, intermediate for algae reared in N-limited medium and highest for algae cultured in non-limited standard medium. Growth inhibition due to FFD-6 was similar for non-limited and nutrient-limited Scenedesmus, but colony formation was stronger in non-limited Scenedesmus than in nutrient limited cultures. The colony inducing effect of the surfactant FFD-6 on Scenedesmus occurs at much lower concentrations than growth inhibition and might affect species interactions, the survival of species and the energy flow along the food chain.

Occurrence and distribution of nonionic surfactants, their degradation products, and linear alkylbenzene sulfonates in coastal waters and sediments in Spain.

PubMed

Petrovic, Mira; Fernández-Alba, Amadeo Rodrigez; Borrull, Francisco; Marce, Rosa Maria; González, Mazo Eduardo; Barceló, Damià

2002-01-01

Spain is one of the European countries that still discharges untreated wastewaters and sewage sludge to the sea. A total of 35 samples of coastal waters and 39 samples of harbor sediments was analyzed. Samples were collected from several hot spots on the Spanish coast, such as the harbors of Tarragona, Almería, and Barcelona, the mouths of the Besos and Llobregat rivers, the Bay of Cadiz, and various yacht harbors at the Mediterranean coast. A generic analytical procedure based on solid-phase extraction-liquid chromatography-atmospheric pressure chemical ionization/electrospray ionization mass spectrometry (SPE-LC-APCI/ESI-MS) was employed for determining the concentrations of alcohol ethoxylates (AEO), nonylphenol ethoxylates (NPEO), coconut diethanol amides (CDEA), nonylphenoxy-monocarboxylates (NPEC), nonylphenol (NP), octylphenol (OP), and linear alkylbenzene sulfonates (LAS) in sediment and water samples. The analysis revealed the presence of considerably high concentrations of NPEOs and NP near the points of discharge of industrial and urban wastewaters. Nonylphenol was found in 47% of water samples and in 77% of all sediment samples analyzed. Values for NP ranged from <0.15 to 4.1 microg/L in seawater and from <8 to 1,050 microg/kg in sediments. Levels of AEOs and CDEAs in seawater and marine sediments are reported for the first time. Concentrations of CDEAs in sediment, which were predominated by C11 through C15 homologues, ranged from 30 to 2,700 microg/kg, while in seawater, concentrations found were up to 24 microg/L. The AEOs were found to accumulate in a bottom sediment and they were detected in all analyzed sediment samples in concentrations from 37 to 1,300 microg/kg.

Submitochondrial particle response to linear alkylbenzene sulfonates, nonylphenol polyethoxylates and their biodegradation derivatives

DOE Office of Scientific and Technical Information (OSTI.GOV)

Argese, E.; Marcomini, A.; Bettiol, C.

1994-05-01

The effects on mitochondrial respiratory parameters of linear alkylbenzene sulfonates (LAS), nonylphenol polyethoxylates (NPEO), and some of their biotransformation products, namely sulfophenyl carboxylates (SPCs), nonylphenol (NP), and nonylphenoxy acetic acid (NP1EC), were recorded by using the in vitro response of submitochondrial particles (SMP) from beef heart. The toxicity of these compounds was estimated by determining their effects on the energy-coupled reverse electron transfer (RET), which is induced by ATP and succinate at the first site level of the respiratory chain and reduces exogenous NAD[sup +] to NADH. The toxicity of the substances, expressed as the toxicant concentration decreasing the reductionmore » rate of NAD[sup +] to an extent of 50% (EC50), ranged from 0.61 mg/L for a commercial LAS mixture to 18,000 mg/L for individual SPCs; from 1.3 mg/L for NPEO, with an average of 10 ethoxy units, to 8.2 and 1.8 mg/L for NP1EC and NP, respectively. These results were related to the molecular structure of each compound class and compared with the toxicity values obtained by a variety of biological systems currently used for toxicity testing. The acute toxicity data have demonstrated that (a) the SMP bioassay is suitable for reproducing the toxicological response of whole organisms, such as fishes and invertebrates, to the tested chemicals; and (b) the hydrophobic moiety of these compounds plays a significant role in eliciting their toxic effects. From a toxicological standpoint, attention must be paid to the occurrence in natural waters of residual LAS, whereas in the case of NPEO both unaltered surfactant and all biotransformation products need to be identified and quantified.« less

[Analysis and identification of emulsifying viscosity reducer by FTIR and 1H NMR].

PubMed

Zhu, Hong; Guan, Run-ling; Shen, Jing-mei

2007-01-01

Separation and purification of viscosity reducer for crude oil were performed with distillation and dissolution-precipitation. The functional group of its main component was identified by FTIR It was deduced that the main component of the crude oil viscosity reducer is the tricopolymer of poly ethyl acrylate/methyl methacrylate/acrylic acid. The structure of the component was also ascertained and quantitively analysed with 1 H NMR and MS. The mol ratio of the three monomers is 37. 1 : 25. 8 : 37. 1, and the mass ratio is 41. 1 : 28. 8 : 29. 8. The structure of the part soluble in methanol was identified by FTIR. The result showed that the nonionic sufactant is poly ethylene oxide with the moleculear mass range of 800-1600, and the anionic surfactant is alkylbenzene sulfonate. The residue is accessory ingredient and water.

The Use of Multi-Reactor Cascade Plasma Electrolysis for Linear Alkylbenzene Sulfonate Degradation

NASA Astrophysics Data System (ADS)

Saksono, Nelson; Ibrahim; Zainah; Budikania, Trisutanti

2018-03-01

Plasma electrolysis is a method that can produce large amounts of hydroxyl radicals to degrade organic waste. The purpose of this study is to improve the effectiveness of Linear alkylbenzene sulfonate (LAS) degradation by using multi-reactor cascade plasma electrolysis. The reactor which operated in circulation system, using 3 reactors series flow and 6 L of LAS with initial concentration of 100 ppm. The results show that the LAS degradation can be improved multi-reactor cascade plasma electrolysis. The greatest LAS degradation is achieved up to 81.91% with energy consumption of 2227.34 kJ/mmol that is obtained during 120 minutes by using 600 Volt, 0.03 M of KOH, and 0.5 cm of the anode depth.

Anionic surfactants in treated sewage and sludges: risk assessment to aquatic and terrestrial environments.

PubMed

Mungray, Arvind Kumar; Kumar, Pradeep

2008-05-01

Compared to low concentrations of anionic surfactants (AS) in activated sludge process effluents (ASP) (<0.2 mg/L), upflow anaerobic sludge blanket-polishing pond (UASB-PP) effluents were found to contain very high concentrations of AS (>3.5 mg/L). AS (or linear alkylbenzen sulfonate, LAS) removals >99% have been found for ASP while in case of UASB-PP it was found to be < or = 30%. AS concentrations averaged 7347 and 1452 mg/kg dry wt. in wet UASB and dried sludges, respectively. Treated sewage from UASB based sewage treatment plants (STPs) when discharged to aquatic ecosystems are likely to generate substantial risk. Post-treatment using 1-1.6d detention, anaerobic, non-algal polishing ponds was found ineffective. Need of utilizing an aerobic method of post-treatment of UASB effluent in place of an anaerobic one has been emphasized. Natural drying of UASB sludges on sludge drying beds (SDBs) under aerobic conditions results in reduction of adsorbed AS by around 80%. Application of UASB sludges on SDBs was found simple, economical and effective. While disposal of treated UASB effluent may cause risk to aquatic ecosystems, use of dried UASB sludges is not likely to cause risk to terrestrial ecosystems.

Mineralization of surfactants by the microbiota of submerged plant detritus.

PubMed

Federle, T W; Ventullo, R M

1990-02-01

In wetlands and canopied bodies of water, plant detritus is an important source of carbon and energy. Detrital materials possess a large surface area for sorption of dissolved organics and are colonized by a large and diverse microbiota. To examine the biodegradation of surfactants by these microorganisms, submerged oak leaves were obtained from a laundromat wastewater pond, its overflow, and a pristine control pond. Leaves were cut into disks and incubated in sterile water amended with 50 mug of C-labeled linear alkylbenzene sulfonate (LAS), linear alcohol ethoxylate, stearyltrimethyl ammonium chloride, distearyldimethyl ammonium chloride, benzoic acid, or mixed amino acids per liter. Sorption of the test compounds to the detritus and evolution of CO(2) were followed with time. All of the compounds sorbed to the detritus to various degrees, with LAS and stearyltrimethyl ammonium chloride the most sorptive and benzoic acid the least. All compounds were mineralized without a lag. With leaves from the laundromat wastewater pond, half-lives were 12.6 days for LAS, 8.4 days for linear alcohol ethoxylate, 14.2 days for stearyltrimethyl ammonium chloride, 1.0 days for benzoic acid, and 2.7 days for mixed amino acids. Mineralization of LAS and linear alcohol ethoxylate by control pond leaves was slower and exhibited an S-shaped rather than a typical first-order pattern. This study shows that detritus represents a significant site of surfactant removal in detritus-rich systems.

Mineralization of Surfactants by Microbiota of Aquatic Plants.

PubMed

Federle, Thomas W; Schwab, Burney S

1989-08-01

The biodegradation of linear alkylbenzene sulfonate (LAS) and linear alcohol ethoxylate (LAE) by the microbiota associated with duckweed (Lemna minor) and the roots of cattail (Typha latifolia) was investigated. Plants were obtained from a pristine pond and a pond receiving wastewater from a rural laundromat. Cattail roots and duckweed plants were incubated in vessels containing sterile water amended with [C]LAS, [C]LAE, or C-labeled mixed amino acids (MAA). Evolution of CO(2) was determined over time. The microbiota of cattail roots from both ponds mineralized LAS, LAE, and MAA without lag periods, and the rates and extents of mineralization were not significantly affected by the source of the plants. Mineralization of LAS and LAE was more rapid in the rhizosphere than in nearby root-free sediments, which exhibited differences as a function of pond. The microbiota of duckweed readily mineralized LAE and MAA but not LAS. The rate and extent of mineralization were not affected by the source of the duckweed.

Mineralization of Surfactants by Microbiota of Aquatic Plants

PubMed Central

Federle, Thomas W.; Schwab, Burney S.

1989-01-01

The biodegradation of linear alkylbenzene sulfonate (LAS) and linear alcohol ethoxylate (LAE) by the microbiota associated with duckweed (Lemna minor) and the roots of cattail (Typha latifolia) was investigated. Plants were obtained from a pristine pond and a pond receiving wastewater from a rural laundromat. Cattail roots and duckweed plants were incubated in vessels containing sterile water amended with [14C]LAS, [14C]LAE, or 14C-labeled mixed amino acids (MAA). Evolution of 14CO2 was determined over time. The microbiota of cattail roots from both ponds mineralized LAS, LAE, and MAA without lag periods, and the rates and extents of mineralization were not significantly affected by the source of the plants. Mineralization of LAS and LAE was more rapid in the rhizosphere than in nearby root-free sediments, which exhibited differences as a function of pond. The microbiota of duckweed readily mineralized LAE and MAA but not LAS. The rate and extent of mineralization were not affected by the source of the duckweed. PMID:16347999

Determination of household and industrial chemicals, personal care products and hormones in leafy and root vegetables by liquid chromatography-tandem mass spectrometry.

PubMed

Aparicio, Irene; Martín, Julia; Abril, Concepción; Santos, Juan Luis; Alonso, Esteban

2018-01-19

A multiresidue method has been developed for the determination of emerging pollutants in leafy and root vegetables. Selected compounds were 6 perfluoroalkyl compounds (5 perfluorocarboxylic acids and perfluorooctanesulfonic acid), 3 non-ionic surfactants (nonylphenol and nonylphenolethoxylates), 8 anionic surfactants (4 alkylsulfates and 4 linear alkylbenzene sulfonates), 4 preservatives (parabens), 2 biocides (triclosan and triclocarban), 2 plasticizers (bisphenol A and di-(2-ethylhexyl)phthalate), 6 UV-filters (benzophenones) and 4 hormones. The method is based on ultrasound-assisted extraction, clean-up by dispersive solid-phase extraction (d-SPE) and liquid chromatography-tandem mass spectrometry analysis. Due to the diversity of the physico-chemical properties of the target compounds, and to better evaluate the influence of sample treatment variables in extraction efficiencies, Box-Behnken design was applied to optimize extraction solvent volume, number of extraction cycles and d-SPE sorbent amount. Linearity (R 2 ) higher than 0.992, accuracy (expressed as relative recoveries) in the range from 81 to 126%, precision (expressed as relative standard deviation) lower than 19% and limits of detection between 0.025 and 12.5ngg -1 dry weight were achieved. The method was applied to leafy vegetables (lettuce, spinach and chard) and root vegetables (carrot, turnip and potato) from a local market. The highest concentrations corresponded to the surfactants reaching levels up to 114ngg -1 (dry weight), in one of the lettuce samples analyzed. Copyright © 2017 Elsevier B.V. All rights reserved.

Mineralization of Surfactants by the Microbiota of Submerged Plant Detritus

PubMed Central

Federle, Thomas W.; Ventullo, Roy M.

1990-01-01

In wetlands and canopied bodies of water, plant detritus is an important source of carbon and energy. Detrital materials possess a large surface area for sorption of dissolved organics and are colonized by a large and diverse microbiota. To examine the biodegradation of surfactants by these microorganisms, submerged oak leaves were obtained from a laundromat wastewater pond, its overflow, and a pristine control pond. Leaves were cut into disks and incubated in sterile water amended with 50 μg of 14C-labeled linear alkylbenzene sulfonate (LAS), linear alcohol ethoxylate, stearyltrimethyl ammonium chloride, distearyldimethyl ammonium chloride, benzoic acid, or mixed amino acids per liter. Sorption of the test compounds to the detritus and evolution of 14CO2 were followed with time. All of the compounds sorbed to the detritus to various degrees, with LAS and stearyltrimethyl ammonium chloride the most sorptive and benzoic acid the least. All compounds were mineralized without a lag. With leaves from the laundromat wastewater pond, half-lives were 12.6 days for LAS, 8.4 days for linear alcohol ethoxylate, 14.2 days for stearyltrimethyl ammonium chloride, 1.0 days for benzoic acid, and 2.7 days for mixed amino acids. Mineralization of LAS and linear alcohol ethoxylate by control pond leaves was slower and exhibited an S-shaped rather than a typical first-order pattern. This study shows that detritus represents a significant site of surfactant removal in detritus-rich systems. Images PMID:16348111

Development of a multiple-class analytical method based on the use of synthetic matrices for the simultaneous determination of commonly used commercial surfactants in wastewater by liquid chromatography-tandem mass spectrometry.

PubMed

Alexandre, Bergé; Barbara, Giroud; Laure, Wiest; Bruno, Domenjoud; Adriana, Gonzalez-Ospina; Emmanuelle, Vulliet

2016-06-10

Discharges of surfactants from wastewater treatment plants are often considered as the principal vector of pollution into the environment. The analysis of complex matrices, such as urban wastewater, suspended solids and biological sludge requires careful preparation of the sample to obtain a sensitive, selective and reproducible analysis. A simple, fast, effective and multi-residue method based on the SPE (water) and QuEChERS (solid matrices) approaches using synthetic matrices for validation and quantification, has been developed for the determination of 16 surfactants in wastewater, suspended solids and biological sludge. This work resulted in an innovative method that was validated to detect and assess several classes of surfactants such as quaternary ammonium compounds, betaïns, alkylphenols and their ethoxylated or sulfated derivatives in urban wastewater and solid matrices. The optimised extraction method exhibited recoveries comprised between 83% and 120% for all the tested compounds in the dissolved matrix and between 50% and 109% for particulate matrix. The limits of quantification of all compounds were comprised between 0.1 and 1.0μg/L for dissolved matrix and between 2 and 1000ng/g (dry weight) in particulate matrix. Linearity was assessed for all compounds within the [LOQ-250LOQ] range. Confidence intervals were also computed in real matrices with less than 15% margin of error for all studied surfactants. This work has confirmed, first and foremost, that surfactants are indeed highly concentrated in urban wastewater. As expected, linear alkylbenzene sulfonates were present at significant concentrations (up to 1-2mg/L). In addition, although biological processing results in significant removal of the total pollution, the residual concentrations at output of WWTP remain significant (up to 100μg/L). Copyright © 2016 Elsevier B.V. All rights reserved.

Synthesis of Amphoteric Sulfonic Ionic Liquid Surfactant and Measurement of Its Surface Properties

NASA Astrophysics Data System (ADS)

Zhao, Xiuli; Zhang, Changbao; Liu, Da; Liu, Haiyan

2018-03-01

Three kinds of amphoteric sulfonic ionic liquid surfactants were synthesized in this paper. Their functional group structures were characterized by infrared spectrometer. The surface properties of them were studied. The results show that the functional group structures of all three products conform to the structure characteristics of amphoteric sulfonic ionic liquid surfactants. The shorter the long chain alkyl carbon chain is, the closer the arrangement of surfactant on the gas-liquid surface will be, and the higher the efficiency in reducing the surface tension..

Environmental Safety of the Use of Major Surfactant Classes in North America

PubMed Central

Cowan-Ellsberry, Christina; Belanger, Scott; Dorn, Philip; Dyer, Scott; McAvoy, Drew; Sanderson, Hans; Versteeg, Donald; Ferrer, Darci

2014-01-01

This paper brings together over 250 published and unpublished studies on the environmental properties, fate, and toxicity of the four major, high-volume surfactant classes and relevant feedstocks. The surfactants and feedstocks covered include alcohol sulfate or alcohol sulfate (AS), alcohol ethoxysulfate (AES), linear alkylbenzene sulfonate (LAS), alcohol ethoxylate (AE), and long-chain alcohol (LCOH). These chemicals are used in a wide range of personal care and cleaning products. To date, this is the most comprehensive report on these substance's chemical structures, use, and volume information, physical/chemical properties, environmental fate properties such as biodegradation and sorption, monitoring studies through sewers, wastewater treatment plants and eventual release to the environment, aquatic and sediment toxicity, and bioaccumulation information. These data are used to illustrate the process for conducting both prospective and retrospective risk assessments for large-volume chemicals and categories of chemicals with wide dispersive use. Prospective risk assessments of AS, AES, AE, LAS, and LCOH demonstrate that these substances, although used in very high volume and widely released to the aquatic environment, have no adverse impact on the aquatic or sediment environments at current levels of use. The retrospective risk assessments of these same substances have clearly demonstrated that the conclusions of the prospective risk assessments are valid and confirm that these substances do not pose a risk to the aquatic or sediment environments. This paper also highlights the many years of research that the surfactant and cleaning products industry has supported, as part of their environmental sustainability commitment, to improve environmental tools, approaches, and develop innovative methods appropriate to address environmental properties of personal care and cleaning product chemicals, many of which have become approved international standard methods. PMID:25170243

Role of dissolved organic carbon upon re-entrainment and surface properties of aquifer bacteria and bacteria-sized microspheres during subsurface transport (Invited)

NASA Astrophysics Data System (ADS)

Harvey, R. W.; Metge, D. W.; Mohanram, A.; Gao, X.; Chorover, J.

2010-12-01

Susceptibilities for in-situ re-entrainment of attached 0.2 and 1.0 μm (diameter) microspheres and groundwater bacteria (Pseudomonas stuzeri and uncultured, native bacteria) were assessed during transport studies involving an organically contaminated, sandy aquifer in Cape Cod, MA. Aquifer sediments between pairs of injection and sampling wells were initially loaded with fluorescently labeled, carboxylated microspheres and bacteria that had been stained with the DNA-specific fluorochrome 4',6-diamidino-2-phenylindole. In response to subsequent hydrodynamic perturbations and injections of deionized water (ionic strength reduction), anionic surfactants (77 μM linear alkylbenzene sulfonates, LAS) and non-ionic surfactant (76 μM polyoxyethylene sorbitan monooleate, Tween 80), differing patterns of re-entrainment were evident for the two colloids. Injections of anionic surfactant and deionized water were the most efficient in causing detachment of the highly hydrophilic and negatively charged microspheres, but largely ineffective in causing re-entrainment of bacteria. In contrast, the nonionic surfactant was highly effective in re-entraining bacteria, but not microspheres. The hydrophobicities and zeta potentials of the indigenous bacteria were highly sensitive to modest concentration changes (0.6 to 1.3 mg L-1) in groundwater dissolved organic carbon (DOC), whereas the microspheres were largely unaffected. The most hydrophilic and negatively charged bacterial community was isolated from groundwater having the lowest DOC. FTIR spectra indicated that the community from the lowest DOC groundwater also had the highest average density of surface carboxyl groups. This indicates that DOC may have a biological effect on native bacteria resulting in changes to surface structures or changes in the makeup of the bacterial community.

Microbial characterization and degradation of linear alkylbenzene sulfonate in an anaerobic reactor treating wastewater containing soap powder.

PubMed

Carosia, Mariana Fronja; Okada, Dagoberto Yukio; Sakamoto, Isabel Kimiko; Silva, Edson Luiz; Varesche, Maria Bernadete Amâncio

2014-09-01

The aim of this study was to evaluate the removal of linear alkylbenzene sulfonate (LAS) in an anaerobic fluidized bed reactor (AFBR) treating wastewater containing soap powder as LAS source. At Stage I, the AFBR was fed with a synthetic substrate containing yeast extract and ethanol as carbon sources, and without LAS; at Stage II, soap powder was added to this synthetic substrate obtaining an LAS concentration of 14 ± 3 mg L(-1). The compounds of soap powder probably inhibited some groups of microorganisms, increasing the concentration of volatile fatty acids (VFA) from 91 to 143 mg HAc L(-1). Consequently, the LAS removal rate was 48 ± 10% after the 156 days of operation. By sequencing, 16S rRNA clones belonging to the phyla Proteobacteria and Synergistetes were identified in the samples taken at the end of the experiment, with a remarkable presence of Dechloromonas sp. and Geobacter sp. Copyright © 2014 Elsevier Ltd. All rights reserved.

Bioremediation of surface water co-contaminated with zinc (II) and linear alkylbenzene sulfonates by Spirulina platensis

NASA Astrophysics Data System (ADS)

Meng, Huijuan; Xia, Yunfeng; Chen, Hong

Potential remediation of surface water contaminated with linear alkylbenzene sulfonates (LAS) and zinc (Zn (II)) by sorption on Spirulina platensis was studied using batch techniques. Results show that LAS can be biodegraded by Spirulina platensis, and its biodegradation rate after 5 days was 87%, 80%, and 70.5% when its initial concentration was 0.5, 1, and 2 mg/L, respectively. The maximum Zn (II) uptake capacity of Spirulina platensis was found to be 30.96 mg/g. LAS may enhance the maximum Zn (II) uptake capacity of Spirulina platensis, which can be attributed to an increase in bioavailability due to the presence of LAS. The biodegradation rates of LAS by Spirulina platensis increased with Zn (II) and reached the maximum when Zn (II) was 4 mg/L. The joint toxicity test showed that the combined effect of LAS and Zn (II) was Synergistic. LAS can enhance the biosorption of Zn (II), and reciprocally, Zn (II) can enhance LAS biodegradation.

Surfactant-enhanced flushing enhances colloid transport and alters macroporosity in diesel-contaminated soil.

PubMed

Guan, Zhuo; Tang, Xiang-Yu; Nishimura, Taku; Katou, Hidetaka; Liu, Hui-Yun; Qing, Jing

2018-02-01

Soil contamination by diesel has been often reported as a result of accidental spillage, leakage and inappropriate use. Surfactant-enhanced soil flushing is a common remediation technique for soils contaminated by hydrophobic organic chemicals. In this study, soil flushing with linear alkylbenzene sulfonates (LAS, an anionic surfactant) was conducted for intact columns (15cm in diameter and 12cm in length) of diesel-contaminated farmland purple soil aged for one year in the field. Dynamics of colloid concentration in column outflow during flushing, diesel removal rate and resulting soil macroporosity change by flushing were analyzed. Removal rate of n-alkanes (representing the diesel) varied with the depth of the topsoil in the range of 14%-96% while the n-alkanes present at low concentrations in the subsoil were completely removed by LAS-enhanced flushing. Much higher colloid concentrations and larger colloid sizes were observed during LAS flushing in column outflow compared to water flushing. The X-ray micro-computed tomography analysis of flushed and unflushed soil cores showed that the proportion of fine macropores (30-250μm in diameter) was reduced significantly by LAS flushing treatment. This phenomenon can be attributed to enhanced clogging of fine macropores by colloids which exhibited higher concentration due to better dispersion by LAS. It can be inferred from this study that the application of LAS-enhanced flushing technique in the purple soil region should be cautious regarding the possibility of rapid colloid-associated contaminant transport via preferential pathways in the subsurface and the clogging of water-conducting soil pores. Copyright © 2017. Published by Elsevier B.V.

Study on the generation of perfluorooctane sulfonate from the aqueous film-forming foam.

PubMed

Kishi, Takahiro; Arai, Mitsuru

2008-11-15

Perfluorooctane sulfonate (C(8)HF(17)SO(3)) and perfluorooctane acid (C(8)HF(15)O(2)) are artificial chemicals and have been used all over the world, mainly as water repellent agents, fluorochemical surfactants, coating agents, etc. However, perfluorooctane sulfonate and perfluorooctane acid are environmental contaminants because of their stability, bio-accumulativeness, and long-term persistence in the ecological environment. At the present day, they are diffused all over the world. Lately, this diffusion is viewed with suspicion and there is a movement towards their restriction, even if the environmental fate of them is still under investigation. Fluorochemical surfactants are key compounds in the aqueous film-forming foam (AFFF) formulations. AFFFs are used for massive conflagration such as industrial fire and petroleum fire because of their efficient fire control. On the other hand, a lot of AFFFs are used in case of massive conflagration and most of them enter ocean and groundwater. Actually, perfluorooctane sulfonate and perfluorooctane sulfonate related substances were detected from the fire-fighting facility of US forces. Therefore, there is the possibility of generating perfluorooctane sulfonate and perfluorooctane sulfonate related substances from fluorochemical surfactants in the AFFFs. In this study, activated sludge added AFFF were analyzed for perfluorooctane sulfonate and perfluorooctane acid with time. And the perfluorooctane sulfonate was directly detected after 2 days using LC-MS. This shows that AFFF can be decomposed perfluorooctane sulfonate by microorganisms easily. However, perfluorooctane sulfonate would not decompose at all. Additionally, activated sludge added N-polyoxyethylene-N-propyl perfluorooctane sulfonamide which is one of the fluorochemical surfactants used in the AFFF was analyzed for perfluorooctane sulfonate and perfluorooctane acid with time and the perfluorooctane sulfonate was detected too.

Determination of alkylbenzenesulfonate surfactants in groundwater using macroreticular resins and carbon-13 nuclear magnetic resonance spectrometry

USGS Publications Warehouse

Thurman, E.M.; Willoughby, T.; Barber, L.B.; Thorn, K.A.

1987-01-01

Alkylbenzenesulfonate surfactants were determined in groundwater at concentrations as low as 0.3 mg/L. The method uses XAD-8 resin for concentration, followed by elution with methanol, separation of anionic and nonionic surfactants by anion exchange, quantitation by titration, and identification by 13C nuclear magnetic resonance spectrometry. Laboratory standards and field samples containing straight-chain and branched-chain alkylbenzenesulfonates, sodium dodecyl sulfate, and alkylbenzene ethoxylates were studied. The XAD-8 extraction of surfactants from groundwater was completed in the field, which simplified sample preservation and reduced the cost of transporting samples.

The Initial Comparison Study of Sodium Lignosulfonate, Sodium Dodecyl Benzene Sulfonate, and Sodium p-Toluene Sulfonate Surfactant for Enhanced Oil Recovery

NASA Astrophysics Data System (ADS)

Khoirul Anas, Argo; Iman Prakoso, Nurcahyo; Sasvita, Dilla

2018-04-01

Surfactant (surface active agent) exhibit numerous interesting properties that enable their use as additional component in mobilising of residual oil from capillary pore after secondary recovery process using gas injection and water flooding. In this study, Sodium Lignosulfonate (SLS) surfactant was successfully synthesized by applying batch method using lignin from oil palm empty fruit bunches as precursor. Furthermore, its performance in reducing interfacial tension of crude oil and formation water colloidal system was compared with commercial available surfactant including Sodium Dodecyl Benzene Sulfonate (SDBS) and Sodium p-Toluene Sulfonate (SpTS). The synthesized SLS surfactant was characterized by using Fourier Transform Infrared (FTIR) spectroscopy. Meanwhile, its performance in reducing interfacial tension of crude oil and formation water colloidal system was analyzed by using compatibility test, phase behaviour analysis, and interfacial tension (IFT) measurement. The compatibility test shows that SLS, SDBS, and SpTS surfactants were compatible with formation water. In addition, the phase behaviour analysis shows that SLS surfactant was better than SpTS surfactant, while SDBS surfactant generates the highest performance proved by the best microemulsion formation resulted by SDBS. Furthermore, the optimum concentration of SLS, SDBS, and SpTS surfactants in reducing the interfacial tension of crude oil and formation water was 1.0%. The IFT measurement indicates that the performance of SLS with the value of 1.67 mN/m was also better than SpTS surfactant with the value of 3.59 mN/m. Meanwhile, SDBS surfactant shows the best performance with the IFT value of 0.47 mN/m.

Nontarget analysis of polar contaminants in freshwater sediments influenced by pharmaceutical industry using ultra-high-pressure liquid chromatography-quadrupole time-of-flight mass spectrometry.

PubMed

Terzic, Senka; Ahel, Marijan

2011-02-01

A comprehensive analytical procedure for a reliable identification of nontarget polar contaminants in aquatic sediments was developed, based on the application of ultra-high-pressure liquid chromatography (UHPLC) coupled to hybrid quadrupole time-of-flight mass spectrometry (QTOFMS). The procedure was applied for the analysis of freshwater sediment that was highly impacted by wastewater discharges from the pharmaceutical industry. A number of different contaminants were successfully identified owing to the high mass accuracy of the QTOFMS system, used in combination with high chromatographic resolution of UHPLC. The major compounds, identified in investigated sediment, included a series of polypropylene glycols (n=3-16), alkylbenzene sulfonate and benzalkonium surfactants as well as a number of various pharmaceuticals (chlorthalidone, warfarin, terbinafine, torsemide, zolpidem and macrolide antibiotics). The particular advantage of the applied technique is its capability to detect less known pharmaceutical intermediates and/or transformation products, which have not been previously reported in freshwater sediments. Copyright © 2010 Elsevier Ltd. All rights reserved.

Mineralization of surfactants by microbiota of aquatic plants. [Lemna minor, Typha latifolia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Federle, T.W.; Schwab, B.S.

1989-08-01

The biodegradation of linear alkylbenzene sulfonate (LAS) and linear alcohol ethoxylate (LAE) by the microbiota associated with duckweed (Lemna minor) and the roots of cattail (Typha latifolia) was investigated. Plants were obtained from a pristine pond and a pond receiving wastewater from a rural laundromat. Cattail roots and duckweed plants were incubated in vessels containing sterile water amended with ({sup 14}C)LAS, ({sup 14}C)LAE, or {sup 14}C-labeled mixed amino acids (MAA). Evolution of {sup 14}CO{sub 2} was determined over time. The microbiota of cattail roots from both ponds mineralized LAS, LAE, and MAA without lag periods, and the rates and extentsmore » of mineralization were not significantly affected by the source of the plants. Mineralization of LAS and LAE was more rapid in the rhizosphere than in nearby root-free sediments, which exhibited differences as a function of pond. The microbiota of duckweed readily mineralized LAE and MAA but not LAS. The rate and extent of mineralization were not affected by the source of the duckweed.« less

Analysis of particulates on tape lift samples

NASA Astrophysics Data System (ADS)

Moision, Robert M.; Chaney, John A.; Panetta, Chris J.; Liu, De-Ling

2014-09-01

Particle counts on tape lift samples taken from a hardware surface exceeded threshold requirements in six successive tests despite repeated cleaning of the surface. Subsequent analysis of the particle size distributions of the failed tests revealed that the handling and processing of the tape lift samples may have played a role in the test failures. In order to explore plausible causes for the observed size distribution anomalies, scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), and time-of-flight secondary ion mass spectrometry (ToF-SIMS) were employed to perform chemical analysis on collected particulates. SEM/EDX identified Na and S containing particles on the hardware samples in a size range identified as being responsible for the test failures. ToF-SIMS was employed to further examine the Na and S containing particulates and identified the molecular signature of sodium alkylbenzene sulfonates, a common surfactant used in industrial detergent. The root cause investigation suggests that the tape lift test failures originated from detergent residue left behind on the glass slides used to mount and transport the tape following sampling and not from the hardware surface.

Interfacial assignment of branched-alkyl benzene sulfonates: A molecular simulation

NASA Astrophysics Data System (ADS)

Liu, Zi-Yu; Wei, Ning; Wang, Ce; Zhou, He; Zhang, Lei; Liao, Qi; Zhang, Lu

2015-11-01

A molecular dynamics simulation was conducted to analyze orientations of sodium branched-alkyl benzene sulfonates molecules at nonane/water interface, which is helpful to design optimal surfactant structures to achieve ultralow interfacial tension (IFT). Through the two dimensional density profiles, monolayer collapses are found when surfactant concentration continues to increase. Thus the precise scope of monolayer is certain and orientation can be analyzed. Based on the simulated results, we verdict the interfacial assignment of branched-alkyl benzene sulfonates at the oil-water interface, and discuss the effect of hydrophobic tail structure on surfactant assignment. Bigger hydrophobic size can slow the change rate of surfactant occupied area as steric hindrance, and surfactant meta hydrophobic tails have a stronger tendency to stretch to the oil phase below the collapsed concentration. Furthermore, an interfacial model with reference to collapse, increasing steric hindrance and charge repulsive force between interfacial surfactant molecules, responsible for effecting of surfactant concentration and structure has been supposed.

Trace organic chemical pollutants from the lake waters of San Pablo City, Philippines by targeted and non-targeted analysis.

PubMed

Dimzon, Ian Ken D; Morata, Ann Selma; Müller, Janine; Yanela, Roy Kristian; Lebertz, Stephan; Weil, Heike; Perez, Teresita R; Müller, Jutta; Dayrit, Fabian M; Knepper, Thomas P

2018-10-15

More than half of the freshwater lakes in the Philippines are small with surface areas of <2 km 2 . The dynamics in these lakes are different from those in the bigger lakes. This study was conducted to determine the organic pollutants and their sources in three of the seven lakes of San Pablo City in Laguna, Philippines: lakes Palakpakin, Sampaloc, and Pandin. Gas Chromatography-Mass Spectrometry (GC-MS) and Liquid Chromatography - Tandem Mass Spectrometry (LC-MS/MS) were used in the targeted and non-targeted analysis of the lake water samples. The three lakes are all volcanic crater lakes but are exposed to different anthropogenic activities, which includes domestic activities, livelihood (farming and aquaculture) and eco-tourism. Due to the presence of rice fields and fruit plantations, chlorpyrifos was detected in the three lakes while other pesticides like cypermethrin, picolinafen and quinoxyfen were additionally found in Lake Sampaloc, which is the biggest of the three lakes and located within the urbanized section of the city. Traces of different surfactants (linear alkylbenzene sulfonates, secondary alkyl sulfonates, alkyl sulfates, alkyl ether sulfates), biocide benzalkonium chloride, insect repellent diethyltoluamide, antibiotics (sulfadiazine and sulfamethoxazole), hypertension drug telmisartan, phosphate-based fire retardants, and artificial sweeteners (acesulfame, cyclamate, saccharin and sucralose) were detected in lakes Sampaloc and Palakpakin. The same surfactants, artificial sweeteners, insect repellant and phosphate-based fire retardants were also found in Lake Pandin, which is mainly used for eco-tourism activities like swimming and boating. The results of this study suggest that the organic pollutants present in the small lakes can be linked to the various human activities in the immediate lake environment. Because small lakes are more prone to environmental stresses, human activities in the said lakes must be regulated to ensure sustainable development. Copyright © 2018 Elsevier B.V. All rights reserved.

Synthesis and properties evaluation of sulfobetaine surfactant with double hydroxyl

NASA Astrophysics Data System (ADS)

Zhou, Ming; Luo, Gang; Zhang, Ze; Li, Sisi; Wang, Chengwen

2017-09-01

A series of sulfobetaine surfactants {N-[(3-alkoxy-2-hydroxyl)propoxy] ethyl-N,N-dimethyl-N-(2-hydroxyl)propyl sulfonate} ammonium chloride were synthesized with raw materials containing linear saturated alcohol, N,N-dimethylethanolamine, sodium 3-chloro-2-hydroxyl propane sulfonic acid and epichlorohydrin. The molecule structures of sulfobetaine surfactants were characterized by FTIR, 1HNMR and elemental analysis. Surface tension measurements can provide us information about the surface tension at the CMC (γCMC), pC20, Γmax and Amin. The pC20 values of sulfobetaine surfactants increase with the hydrophobic chain length increasing. Amin values of the surfactants decrease with increasing hydrophobic chain length from 10 to 14. The critical micelle concentration (CMC) and surface tension (γCMC) values of the sulfobetaine surfactants decrease with increasing hydrophobic chain length from 10 to 16. The lipophilicity of surfactant was enhanced with the increase of the carbon chain, however, the ability of anti-hard water was weakened. The minimum oil/water interfacial tension of four kinds of sulfobetaine surfactants is 10-2-10-3 mN/m magnitude, which indicates that the synthesized bis-hydroxy sulfobetaine surfactants have a great ability to reduce interfacial tension in the surfactant flooding system. The surface tension (γCMC) values of synthesized surfactants were lower compared with conventional anionic surfactant sodium dodecyl sulfonate.

Effects and risk assessment of linear alkylbenzene sulfonates in agricultural soil. 5. Probabilistic risk assessment of linear alkylbenzene sulfonates in sludge-amended soils.

PubMed

Jensen, J; Løkke, H; Holmstrup, M; Krogh, P H; Elsgaard, L

2001-08-01

Linear alkylbenzene sulfonates (LAS) can be found in high concentrations in sewage sludge and, hence, may enter the soil compartment as a result of sludge application. Here, LAS may pose a risk for soil-dwelling organisms. In the present probabilistic risk assessment, statistical extrapolation has been used to assess the risk of LAS to soil ecosystems. By use of a log-normal distribution model, the predicted no-effect concentration (PNEC) was estimated for soil fauna, plants, and a combination of these. Due to the heterogeneous endpoints for microorganisms, including functional as well as structural parameters, the use of sensitivity distributions is not considered to be applicable to this group of organisms, and a direct, expert evaluation of toxicity data was used instead. The soil concentration after sludge application was predicted for a number of scenarios and used as the predicted environmental concentration (PEC) in the risk characterization and calculation of risk quotients (RQ = PEC/PNEC). A LAS concentration of 4.6 mg/kg was used as the current best estimate of PNEC in all RQ calculations. Three levels of LAS contamination (530, 2,600, and 16,100 mg/kg), three half-lives (10, 25, and 40 d), and five different sludge loads (2, 4, 6, 8, and 10 t/ha) were included in the risk scenarios. In Denmark, the initial risk ratio would reach 1.5 in a realistic worst-case consideration. For countries not having similar sludge regulations, the estimated risk ratio may initially be considerably higher. However, even in the most extreme scenarios, the level of LAS is expected to be well beyond the estimated PNEC one year after application. The present risk assessment, therefore, concludes that LAS does not pose a significant risk to fauna, plants, and essential functions of agricultural soils as a result of normal sewage sludge amendment. However, risks have been identified in worst-case scenarios.

Study of Synthesis Polyethylene glycol oleate Sulfonated as an Anionic Surfactant for Enhanced Oil Recovery (EOR)

NASA Astrophysics Data System (ADS)

Sampora, Yulianti; Juwono, Ariadne L.; Haryono, Agus; Irawan, Yan

2017-11-01

Mechanical Enhanced Oil Recovery (EOR) through chemical injection is using an anionic surfactant to improve the recovery of oil residues, particularly in a reservoir area that has certain characteristics. This case led the authors to conduct research on the synthesis of an anionic surfactant based on oleic acid and polyethylene glycol 400 that could be applied as a chemical injection. In this work, we investigate the sulfonation of Polyethylene glycol oleate (PDO) in a sulfuric acid agent. PDO in this experiment was derived from Indonesian palm oil. Variation of mole reactant and reaction time have been studied. The surfactant has been characterized by measuring the interfacial tension, acid value, ester value, saponification value, iodine value, Fourier Transform Infrared (FTIR), and particle size analyzer. There is a new peak at 1170-1178 cm-1 indicating that S=O bond has formed. PDO sulfonate exhibits good surface activity due to interfacial tension of 0,003 mN/m. Thus, polyethylene glycol oleate sulfonate was successfully synthesized and it could be useful as a novel an anionic surfactant.

Synthesis of methyl ester sulfonate surfactant from crude palm oil as an active substance of laundry liquid detergent

NASA Astrophysics Data System (ADS)

Slamet, Ibadurrohman, Muhammad; Wulandari, Pangiastika Putri

2017-11-01

Liquid detergent with combination of MES surfactant and TiO2 nanoparticles to remove and degrade the dirt in the form of methylene blue and produce waste with the lowest surfactant residual concentration has been done. The formation of MES is carried out by esterification and transesterification of crude palm oil, sulfonation, refining, and neutralization. The photocatalyst TiO2 nanoparticles is added as an additive to improve surfactant performance in removing dirt and degrading organic compounds. MES formation is performed by varying the mole ratio of the reactants in the esterification and transesterification reactions, and the mole ratios between methyl esters and NaHSO3 during the sulfonation reaction. Variations of MES surfactant and TiO2 nanoparticles compositions were performed to obtain detergent stability. Data analysis technique in this research is characterization of methyl ester, MES surfactant, and detergent using UV-Vis spectrophotometer instrument, FTIR, GC-MS, and LC-MS. The optimum conditions in the esterification and transesterification process were each mole ratio of 1: 6 between CPO and methanol based on the highest conversion, 99%. The optimum condition of the sulfonation process is the 1: 1.5 mole ratio between methyl ester and NaHSO3 based on the lowest surface tension value, which is about 36 dyne/cm.

Perfluorooctane sulfonate (PFOS) depletion in beef cattle

USDA-ARS?s Scientific Manuscript database

Perfluorooctane sulfonate (PFOS) is an industrial chemical that is used as a surfactant in several manufactured consumer products but is also a breakdown product from other chemical surfactants. As a result of its extensive use, PFOS is ubiquitous in the environment and is often detected in biosoli...

Synergism between airborne singlet oxygen and a trisubstituted olefin sulfonate for the inactivation of bacteria.

PubMed

Choudhury, Rajib; Greer, Alexander

2014-04-01

The reactivity of a trisubstituted alkene surfactant (8-methylnon-7-ene-1 sulfonate, 1) to airborne singlet oxygen in a solution containing E. coli was examined. Surfactant 1 was prepared by a Strecker-type reaction of 9-bromo-2-methylnon-2-ene with sodium sulfite. Submicellar concentrations of 1 were used that reacted with singlet oxygen by an "ene" reaction to yield two hydroperoxides (7-hydroperoxy-8-methylnon-8-ene-1 sulfonate and (E)-8-hydroperoxy-8-methylnon-6-ene-1 sulfonate) in a 4:1 ratio. Exchanging the H2O solution for D2O where the lifetime of solution-phase singlet oxygen increases by 20-fold led to an ∼2-fold increase in the yield of hydroperoxides pointing to surface activity of singlet oxygen with the surfactant in a partially solvated state. In this airborne singlet oxygen reaction, E. coli inactivation was monitored in the presence and absence of 1 and by a LIVE/DEAD cell permeabilization assay. It was shown that the surfactant has low dark toxicity with respect to the bacteria, but in the presence of airborne singlet oxygen, it produces a synergistic enhancement of the bacterial inactivation. How the ene-derived surfactant hydroperoxides can provoke (1)O2 toxicity and be of general utility is discussed.

Effect of sodium dodecylbenzene sulfonate on subtilisin Carlsberg proteolysis of an immobilized ovalbumin film.

PubMed

Foose, Ladan L; Blanch, Harvey W; Radke, C J

2009-03-01

Enzymatic degradation of immobilized ovalbumin multilayer films by subtilisin Carlsberg was investigated using in situ ellipsometry. Changes in the substrate cleavage rate in the presence of an anionic surfactant, sodium dodecylbenzene sulfonate (SDBS), were assessed. Exposure of the protein film to SDBS prior to introduction of the enzyme increased the measured proteolysis rate threefold. Surfactant increased the measured film thickness, absorbing into the protein film and causing swelling. Surfactant-induced film swelling was reversible upon aqueous rinsing. Nevertheless, exposure of enzyme to the surfactant-rinsed film increased the proteolysis rate, most likely due to irreversible conformational changes induced in the substrate film by the surfactant. Simultaneous addition of SDBS with enzyme after the initial surfactant exposure did not produce additional protein-removal benefit.

Physiological Response of the Hard Coral Pocillopora verrucosa from Lombok, Indonesia, to Two Common Pollutants in Combination with High Temperature.

PubMed

Kegler, Pia; Baum, Gunilla; Indriana, Lisa F; Wild, Christian; Kunzmann, Andreas

2015-01-01

Knowledge on interactive effects of global (e.g. ocean warming) and local stressors (e.g. pollution) is needed to develop appropriate management strategies for coral reefs. Surfactants and diesel are common coastal pollutants, but knowledge of their effects on hard corals as key reef ecosystem engineers is scarce. This study thus investigated the physiological reaction of Pocillopora verrucosa from Lombok, Indonesia, to exposure with a) the water-soluble fraction of diesel (determined by total polycyclic aromatic hydrocarbons (PAH); 0.69 ± 0.14 mg L-1), b) the surfactant linear alkylbenzene sulfonate (LAS; 0.95 ± 0.02 mg L-1) and c) combinations of each pollutant with high temperature (+3°C). To determine effects on metabolism, respiration, photosynthetic efficiency and coral tissue health were measured. Findings revealed no significant effects of diesel, while LAS resulted in severe coral tissue losses (16-95% after 84 h). High temperature led to an increase in photosynthetic yield of corals after 48 h compared to the control treatment, but no difference was detected thereafter. In combination, diesel and high temperature significantly increased coral dark respiration, whereas LAS and high temperature caused higher tissue losses (81-100% after 84 h) and indicated a severe decline in maximum quantum yield. These results confirm the hypothesized combined effects of high temperature with either of the two investigated pollutants. Our study demonstrates the importance of reducing import of these pollutants in coastal areas in future adaptive reef management, particularly in the context of ocean warming.

Physiological Response of the Hard Coral Pocillopora verrucosa from Lombok, Indonesia, to Two Common Pollutants in Combination with High Temperature

PubMed Central

Kegler, Pia; Baum, Gunilla; Indriana, Lisa F.; Wild, Christian; Kunzmann, Andreas

2015-01-01

Knowledge on interactive effects of global (e.g. ocean warming) and local stressors (e.g. pollution) is needed to develop appropriate management strategies for coral reefs. Surfactants and diesel are common coastal pollutants, but knowledge of their effects on hard corals as key reef ecosystem engineers is scarce. This study thus investigated the physiological reaction of Pocillopora verrucosa from Lombok, Indonesia, to exposure with a) the water-soluble fraction of diesel (determined by total polycyclic aromatic hydrocarbons (PAH); 0.69 ± 0.14 mg L-1), b) the surfactant linear alkylbenzene sulfonate (LAS; 0.95 ± 0.02 mg L-1) and c) combinations of each pollutant with high temperature (+3°C). To determine effects on metabolism, respiration, photosynthetic efficiency and coral tissue health were measured. Findings revealed no significant effects of diesel, while LAS resulted in severe coral tissue losses (16–95% after 84 h). High temperature led to an increase in photosynthetic yield of corals after 48 h compared to the control treatment, but no difference was detected thereafter. In combination, diesel and high temperature significantly increased coral dark respiration, whereas LAS and high temperature caused higher tissue losses (81–100% after 84 h) and indicated a severe decline in maximum quantum yield. These results confirm the hypothesized combined effects of high temperature with either of the two investigated pollutants. Our study demonstrates the importance of reducing import of these pollutants in coastal areas in future adaptive reef management, particularly in the context of ocean warming. PMID:26555818

Interactions of structurally modified surfactants with reservoir minerals: Calorimetric, spectroscopic and electrokinetic study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Somasundaran, P.; Sivakumar, A.; Xu, Q.

1991-03-01

The objective of this project is to elucidate mechanisms of adsorption of structurally modified surfactants on reservoir minerals and to develop a full understanding of the effect of the surfactant structure on the nature of the adsorbed layers at the molecular level. An additional aim is to study the adsorption of surfactant mixtures on simple well-characterized minerals and on complex minerals representing real conditions. The practical goal of these studies is the identification of the optimum surfactant structures and their combinations for micellar flooding. In this work, the experiments on adsorption were focussed on the position of sulfonate and methylmore » groups on the aromatic ring of alkyl xylene sulfonates. A multi-pronged approach consisting of calorimetry, electrokinetics, wettability and spectroscopy is planned to elucidate the adsorption mechanism of surfactants and their mixtures on minerals such as alumina and kaolinite. 32 refs., 15 figs., 7 tabs.« less

The relative risk and its distribution of endocrine disrupting chemicals, pharmaceuticals and personal care products to freshwater organisms in the Bohai Rim, China.

PubMed

Zhang, Meng; Shi, Yajuan; Lu, Yonglong; Johnson, Andrew C; Sarvajayakesavalu, Suriyanarayanan; Liu, Zhaoyang; Su, Chao; Zhang, Yueqing; Juergens, Monika D; Jin, Xiaowei

2017-07-15

In this study, the risks to aquatic organisms posed by 12 commonly detected pharmaceuticals and personal care products (PPCPs) and endocrine disrupting chemicals (EDCs) that are extensively used in Bohai coastal region of China were examined. These were linear alkylbenzene sulfonate (LAS), nonylphenol (NP), diethylhexyl phthalate (DEHP), norfloxacin (NOR), sulfamethoxazole (SMX), erythromycin (ERY), bisphenol A (BPA), ofloxacin (OFL), carbamazepine (CBZ), naproxen (NPX), atenolol (ATL) and metoprolol (MET). Their relative risk was ranked based on the proximity between the medians of the reported effect concentrations and measured river or lake water concentrations. The surfactants (LAS) and endocrine disrupting chemicals NP (a breakdown product of the surfactant nonylphenol polyethoxylate) and DEHP (a plasticizer) were identified as posing the greatest risk from this range of chemicals. LAS had a hundred-fold higher risk than any of the pharmaceuticals. The highest risk ranked pharmaceuticals were all antibiotics. Zinc (Zn) and mercury (Hg) were added to the comparison as representative heavy metals. Zn posed a risk higher than all the organics. The risk posed by Hg was less than the surfactants but greater than the selected pharmaceuticals. Whereas LAS and DEHP could cause harmful effects to all the wildlife groups, NP and BPA posed the greatest risk to fish. Antibiotics showed the highest risk to algae. Spatial and temporal distributions of PPCPs and EDCs were conducted for risk identification, source analysis and seasonal change exploration. Municipal sewage effluent linked to urban areas was considered to be the major source of pharmaceuticals. With regard to seasonal influence the risk posed by LAS to the aquatic organisms was significantly affected by wet and dry seasonal change. The dilution effects were the common feature of LAS and ERY risks. The difference in LAS and ERY risk patterns along the rivers was mainly affected by the elimination process. Copyright © 2017 Elsevier B.V. All rights reserved.

Differential effects of dissolved organic carbon upon re-entrainment and surface properties of groundwater bacteria and bacteria-sized microspheres during transport through a contaminated, sandy aquifer

USGS Publications Warehouse

Harvey, R.W.; Metge, D.W.; Mohanram, A.; Gao, X.; Chorover, J.

2011-01-01

Injection-and-recovery studies involving a contaminated, sandy aquifer (Cape Cod, Massachusetts) were conducted to assess the relative susceptibility for in situ re-entrainment of attached groundwater bacteria (Pseudomonas stuzeri ML2, and uncultured, native bacteria) and carboxylate-modified microspheres (0.2 and 1.0 μm diameters). Different patterns of re-entrainment were evident for the two colloids in response to subsequent injections of groundwater (hydrodynamic perturbation), deionized water (ionic strength alteration), 77 μM linear alkylbenzene sulfonates (LAS, anionic surfactant), and 76 μM Tween 80 (polyoxyethylene sorbitan monooleate, a very hydrophobic nonionic surfactant). An injection of deionized water was more effective in causing detachment of micrsopheres than were either of the surfactants, consistent with the more electrostatic nature of microsphere’s attachment, their extreme hydrophilicity (hydrophilicity index, HI, of 0.99), and negative charge (zeta potentials, ζ, of −44 to −49 mv). In contrast, Tween 80 was considerably more effective in re-entraining the more-hydrophobic native bacteria. Both the hydrophilicities and zeta potentials of the native bacteria were highly sensitive to and linearly correlated with levels of groundwater dissolved organic carbon (DOC), which varied modestly from 0.6 to 1.3 mg L−1. The most hydrophilic (0.52 HI) and negatively charged (ζ −38.1 mv) indigenous bacteria were associated with the lowest DOC. FTIR spectra indicated the latter community had the highest average density of surface carboxyl groups. In contrast, differences in groundwater (DOC) had no measurable effect on hydrophilicity of the bacteria-sized microspheres and only a minor effect on their ζ. These findings suggest that microspheres may not be very good surrogates for bacteria in field-scale transport studies and that adaptive (biological) changes in bacterial surface characteristics may need to be considered where there is longer-term exposure to contaminant DOC.

An evaluation of the mobility of pathogen indicators, Escherichia coli and bacteriophage MS-2, in a highly weathered tropical soil under unsaturated conditions

USGS Publications Warehouse

Wong, T.-P.; Byappanahalli, M.; Yoneyama, B.; Ray, C.

2008-01-01

Laboratory column experiments were conducted to study the effects of anionic polyacrylamide (PAM) polymer and surfactant linear alkylbenzene sulfonate (LAS) on the movement of Escherichia coli and the FRNA phage MS-2. The study was designed to evaluate if PAM or PAM + LAS would enhance the mobility of human pathogens in tropical soils under unsaturated conditions. No breakthrough of phage was observed in a 10 cm column after passing 100 pore volumes of solution containing 1 ?? 108 plaque-forming units (PFU)/ml. In later experiments, after passing 10-20 pore volumes of influent containing 1 ?? 108/ml MS-2 or E. coli through 15 cm columns, the soil was sliced and the organisms eluted. Phage moved slightly deeper in the polymer-treated column than in the control column. There was no measurable difference in the movement of E. coli in either polymer-treated or control columns. The properties of the soil (high amounts of metal oxides, kaolinitic clay), unsaturated flow conditions, and relatively high ionic strengths of the leaching solution attributed to significant retention of these indicators. The impacts of PAM and LAS on the mobility of E. coli or MS-2 phage in the chosen soils were not significant. ?? IWA Publishing 2008.

Determination of toxic compounds in paper-recycling process waters by gas chromatography-mass spectrometry and liquid chromatography-mass spectrometry.

PubMed

Rigol, A; Latorre, A; Lacorte, S; Barceló, D

2002-07-19

Three analytical methods were developed for the determination of toxic compounds in recirculating waters of a paper-recycling industry. Three main groups of compounds were considered: (i) wood extractives originated from the raw material; (ii) biocides added during the production process and (iii) surfactants and other adjuvants present in the formulates of these biocides. Wood extractives considered in this study included fatty and resin acids. They were analysed by liquid-liquid extraction using methyl tert.-butyl ether, followed by gas chromatography-mass spectrometry for previous formation of the respective trimethylsilyl esters. Water samples were also extracted with Oasis HLB (copolymer [poly(divinylbenzene-co-N-vinylpyrrolidone]) solid-phase extraction cartridges of 60 mg and analysed by liquid chromatography-electrospray mass spectrometry for the determination of additives and biocides. Using these two approaches levels up to 15 mg/l for total resin and fatty acids, 5 mg/l for alkylbenzene sulfonates and 2-(thiocyanomethylthio)benzotiazol, 100 microg/l for bisphenol A and 2,2-dibromo-3-nitrilepropionamide, and 300 microg/l for nonylphenol ethoxycarboxylate were detected in process waters at different production treatment stages. These levels are of relevance since poor water quality affects the paper-recycling process, the primary water treatment process and eventually, the environmental water quality.

Wide-range and accurate modeling of linear alkylbenzene sulfonate (LAS) adsorption/desorption on agricultural soil.

PubMed

Oliver-Rodríguez, B; Zafra-Gómez, A; Reis, M S; Duarte, B P M; Verge, C; de Ferrer, J A; Pérez-Pascual, M; Vílchez, J L

2015-11-01

In this paper, rigorous data and adequate models about linear alkylbenzene sulfonate (LAS) adsorption/desorption on agricultural soil are presented, contributing with a substantial improvement over available adsorption works. The kinetics of the adsorption/desorption phenomenon and the adsorption/desorption equilibrium isotherms were determined through batch studies for total LAS amount and also for each homologue series: C10, C11, C12 and C13. The proposed multiple pseudo-first order kinetic model provides the best fit to the kinetic data, indicating the presence of two adsorption/desorption processes in the general phenomenon. Equilibrium adsorption and desorption data have been properly fitted by a model consisting of a Langmuir plus quadratic term, which provides a good integrated description of the experimental data over a wide range of concentrations. At low concentrations, the Langmuir term explains the adsorption of LAS on soil sites which are highly selective of the n-alkyl groups and cover a very small fraction of the soil surface area, whereas the quadratic term describes adsorption on the much larger part of the soil surface and on LAS retained at moderate to high concentrations. Since adsorption/desorption phenomenon plays a major role in the LAS behavior in soils, relevant conclusions can be drawn from the obtained results. Copyright © 2015 Elsevier Ltd. All rights reserved.

EFFECTS OF PRENATAL PERFLUOROOCTANE SULFONATE (PFOS) EXPOSURE ON LUNG MATURATION IN THE PERINATAL RAT

EPA Science Inventory

Background: Perfluorooctane sulfonate (PFOS), found widely in wildlife and humans, is environmentally and metabolically stable. Environmental PFOS may be from its use as a surfactant, hydrolysis of perfluorooctanesulfonyl fluoride, and degradation of N-alkyl-perfluorooctanesulfon...

Evaluation of eggshell membrane-based bio-adsorbent for solid-phase extraction of linear alkylbenzene sulfonates coupled with high-performance liquid chromatography.

PubMed

Wang, Weidong; Chen, Bo; Huang, Yuming; Cao, Jia

2010-09-03

The potential of eggshell membrane (ESM) as a novel solid-phase extraction bio-adsorbent was investigated in the present study. The ESM with a unique structure of intricate lattice network showed a predominant ability to capture linear alkylbenzene sulfonates (LAS) as a model of organic pollutants by the hydrophobic interactions between ESM and LAS molecular at pH very close to the isoelectric point of ESM, which was similar to the most widely used trapping mechanism for SPE. Under the optimal conditions, the breakthrough capacities of the ESM packed cartridge for C10-C13 LAS homologues were found to be 30, 53, 50, and 43microgg(-1), respectively. On the basis of high-performance liquid chromatography separation and UV detection of LAS homologues, the proposed system could respond down to 0.027ngmL(-1) of LAS with a linear calibration range from 0.2 to 100ngmL(-1), showing a good LAS enrichment ability of eggshell membrane biomaterial with high sensitivity, and could be successfully used for the detection of residual LAS in environmental water samples. The reproducibility among columns was satisfactory (RSD among columns is less than 10%). A comparison study with ESM, C8 and C18 as adsorbents for LAS demonstrated that ESM-based bio-adsorbent was advantageous over C8 and C18, the widely used traditional adsorbents. 2010 Elsevier B.V. All rights reserved.

Simulation of Organic Matter and Pollutant Evolution during Composting: The COP-Compost Model.

PubMed

Lashermes, G; Zhang, Y; Houot, S; Steyer, J P; Patureau, D; Barriuso, E; Garnier, P

2013-01-01

Organic pollutants (OPs) are potentially present in composts and the assessment of their content and bioaccessibility in these composts is of paramount importance. In this work, we proposed a model to simulate the behavior of OPs and the dynamic of organic C during composting. This model, named COP-Compost, includes two modules. An existing organic C module is based on the biochemical composition of the initial waste mixture and simulates the organic matter transformation during composting. An additional OP module simulates OP mineralization and the evolution of its bioaccessibility. Coupling hypotheses were proposed to describe the interactions between organic C and OP modules. The organic C module, evaluated using experimental data obtained from 4-L composting pilots, was independently tested. The COP-Compost model was evaluated during composting experiments containing four OPs representative of the major pollutants detected in compost and targeted by current and future regulations. These OPs included a polycyclic aromatic hydrocarbon (fluoranthene), two surfactants (4--nonylphenol and a linear alkylbenzene sulfonate), and an herbicide (glyphosate). Residues of C-labeled OP with different bioaccessibility were characterized by sequential extraction and quantified as soluble, sorbed, and nonextractable fractions. The model was calibrated and coupling the organic C and OP modules improved the simulation of the OP behavior and bioaccessibility during composting. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Degradation of linear alkylabenzene sulfonate (LAS) and its compounds in Donghu Lake (Hubei, P.R.C.) determined by high performance liquid chromatography (HPLC)

NASA Astrophysics Data System (ADS)

Ayfer, Yediler; Xu, Ying; Zhang, Yongyuan; Chen, Junjian

1990-06-01

Commercial linear alkylbenzene sulfonate (LAS), mixture of alkylchain lengths and phenyl position isomers (C10-C13), is widely used as a major constituent of household and industrial detergents in the People's Republic of China. Degradation process and behaviour of LAS compounds during an 82-hour lake water die-away study, with an added LAS concentration of 1.5mg·L-1, was quantified and accomplished by HPLO-UV after extractionon the SepPek C18 reversed-phase cartridges. The degradation rate became progressively faster with increasing chain length. The technique described in this study is fast, sensitive and specific, and can be used to determine low levels of LAS and for establishing water quality criteria and standards relating to LAS and its compounds.

Perfluoroctane sulfonate-induced changes in fetal rat liver gene expression

EPA Science Inventory

In utero exposure of rats to perfluorooctane sulfonate (PFOS, C8F17SO3), a widely disseminated product of the surfactant and coating industries, is associated with residual hepatoxic complications in the surviving offspring. This hepatocellular hypertrophy resembles that observe...

DETERMINATION OF ALKYLATED & SULFONATED DIPHENYL OXIDE SULFACTANT BY HIGH PERFORMANCE LIQUID CHROMATOGRAPHY

EPA Science Inventory

Methods for the determination of the anionic surfactant Dowfax 8390 are described. Dowfax is a complex mixture of various alkylated and sulfonated diphenyl oxides. The primary component of Dowfax is monoalkylated disulfonated diphenyl oxide (MADS). This work uses ion pairing chro...

Toxicological properties and risk assessment of the anionic surfactants category: Alkyl sulfates, primary alkane sulfonates, and α-olefin sulfonates.

PubMed

Wibbertmann, Axel; Mangelsdorf, Inge; Gamon, Konrad; Sedlak, Richard

2011-07-01

The category of the anionic surfactants (ANS) consisting of 46 alkyl sulfates, 6 primary alkane sulfonates, and 9 α-olefin sulfonates has been assessed under the high production volume (HPV) chemicals program of the Organisation for Economic Cooperation and Development (OECD) in 2007. In this review the toxicological properties of these chemicals are summarized. The chemicals of this category are used predominantly in detergents, household cleaning products, and cosmetics. These chemicals show low acute and repeat dose toxicity. There was no evidence of genetic or reproductive toxicity, or carcinogenicity. There also was no indication for sensitizing properties. Skin and eye irritating effects in consumers are not to be expected. For consumers, the calculated body burden is about 10,000 times lower than the lowest NOAEL value in experimental animals, so that adverse effects caused by substances of the ANS category can be excluded. Copyright © 2011 Elsevier Inc. All rights reserved.

Exposure to perfluorooctane sulfonate during pregnancy in rat and mouse. I: maternal and prenatal evaluations

EPA Science Inventory

Abstract: The maternal and developmental toxicities of perfluorooctane sulfonate (PFOS, C8F17SO3-) were evaluated in the rat and mouse. PFOS is an environmentally persistent compound used as a surfactant and occurs as a degradation product of both perfluorooctane sulfonyl fluorid...

Assessment of chemical fate in the environment using evaluative, regional and local-scale models: Illustrative application to chlorobenzene and linear alkylbenzene sulfonates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mackay, D.; Di Guardo, A.; Paterson, S.

Evaluation of chemical fate in the environment has been suggested to be best accomplished using a five-stage process in which a sequence of increasing site-specific multimedia mass balance models is applied. This approach is illustrated for chlorobenzene and linear alkylbenzene sulfonates (LAS). The first two stages involve classifying the chemical and quantifying the emissions into each environmental compartment. In the third stage, the characteristics of the chemical are determined using the evaluative equilibrium criterion model, which is capable of treating a variety of chemicals including those that are in volatile and insoluble in water. This evaluation is conducted in threemore » steps using levels 1, 2, and 3 versions of the model, which introduce increasing complexity and more realistic representations of the environment. In the fourth stage, ChemCAN, which is a level 3 model for specific regions of Canada, is used to predict the chemical`s fate in southern Ontario. The final stage is to apply local environmental models to predict environmental exposure concentrations. For chlorobenzene, the local model was the SoilFug model, which predicts the fate of agrochemicals, and for LAS the WW-TREAT, GRiDS, and ROUT models were used to predict the fate of LAS in a sewage treatment plant and in riverine receiving waters. It is concluded that this systematic approach provides a comprehensive assessment of chemical fate, revealing the broad characteristics of chemical behavior and quantifying the likely local and regional exposure levels.« less

Kinetics of methane production and biodegradation of linear alkylbenzene sulfonate from laundry wastewater.

PubMed

Motteran, Fabrício; Braga, Juliana K; Silva, Edson L; Varesche, Maria Bernadete A

2016-12-05

This study evaluates the kinetics of methane production and degradation of standard linear alkylbenzene sulfonate (LAS) (50 ± 3.5 mg/L) and LAS from laundry wastewater (85 ± 2.1 mg/L) in anaerobic batch reactors at 30°C with different sources of inoculum. The inocula were obtained by auto-fermentation (AFM) and UASB reactors from wastewater treatment of poultry slaughterhouse (SGH), swine production (SWT) and wastewater treatment thermophilic of sugarcane industry (THR). The study was divided into three phases: synthetic substrate (Phase I), standard LAS (Phase II) and LAS from laundry wastewater (Phase III). For SGH, the highest values for cumulative methane productions (1,844.8 ± 149 µmol-Phase II), methane production rate (70.8 ± 88 µmol/h-Phase II and 4.01 ± 07 µmol/h-Phase III) were observed. The use of thermophilic biomass (THR) incubated at 30°C was not favorable for methane production and LAS biodegradation, but the highest kinetic coefficient degradation (k 1 app ) was obtained for LAS (0.33 ± 0.3 h) compared with mesophilic biomass (SGH and SWT) (0.13 ± 0.02 h). Therefore, both LAS sources influenced the kinetics of methane production and organic matter degradation. For SGH, inoculum obtained the highest LAS degradation. In the SGH inoculum sequenced by MiSeq-Illumina was identified genera (VadinCA02, Candidatus Cloacamonas, VadinHB04, PD-UASB-13) related to degrade toxic compounds. Therefore, it recommended the reactor mesophilic inoculum UASB (SGH) for the LAS degradation.

Environmental monitoring study of linear alkylbenzene sulfonates and insoluble soap in Spanish sewage sludge samples.

PubMed

Cantarero, Samuel; Zafra-Gómez, Alberto; Ballesteros, Oscar; Navalón, Alberto; Reis, Marco S; Saraiva, Pedro M; Vílchez, José L

2011-01-01

In this work we present a monitoring study of linear alkylbenzene sulfonates (LAS) and insoluble soap performed on Spanish sewage sludge samples. This work focuses on finding statistical relations between LAS concentrations and insoluble soap in sewage sludge samples and variables related to wastewater treatment plants such as water hardness, population and treatment type. It is worth to mention that 38 samples, collected from different Spanish regions, were studied. The statistical tool we used was Principal Component Analysis (PC), in order to reduce the number of response variables. The analysis of variance (ANOVA) test and a non-parametric test such as the Kruskal-Wallis test were also studied through the estimation of the p-value (probability of obtaining a test statistic at least as extreme as the one that was actually observed, assuming that the null hypothesis is true) in order to study possible relations between the concentration of both analytes and the rest of variables. We also compared LAS and insoluble soap behaviors. In addition, the results obtained for LAS (mean value) were compared with the limit value proposed by the future Directive entitled "Working Document on Sludge". According to the results, the mean obtained for soap and LAS was 26.49 g kg(-1) and 6.15 g kg(-1) respectively. It is worth noting that LAS mean was significantly higher than the limit value (2.6 g kg(-1)). In addition, LAS and soap concentrations depend largely on water hardness. However, only LAS concentration depends on treatment type.

Perfluorooctane sulfonate plasma half-life determination and long term tissue distribution in beef cattle (Bos taurus)

USDA-ARS?s Scientific Manuscript database

Perfluorooctane sulfonate (PFOS) is used in consumer products as a surfactant and is found in industrial and consumer waste which ends up in wastewater treatment plants (WWTPs). PFOS does not breakdown during WWTP processes and accumulates in the biosolids. Common practices include application of bi...

Dynamics of Surfactant Clustering at Interfaces and Its Influence on the Interfacial Tension: Atomistic Simulation of a Sodium Hexadecane-Benzene Sulfonate-Tetradecane-Water System.

PubMed

Paredes, Ricardo; Fariñas-Sánchez, Ana Isabel; Medina-Rodrı Guez, Bryan; Samaniego, Samantha; Aray, Yosslen; Álvarez, Luis Javier

2018-03-06

The process of equilibration of the tetradecane-water interface in the presence of sodium hexadecane-benzene sulfonate is studied using intensive atomistic molecular dynamics simulations. Starting as an initial point with all of the surfactants at the interface, it is obtained that the equilibration time of the interface (several microseconds) is orders of magnitude higher than previously reported simulated times. There is strong evidence that this slow equilibration process is due to the aggregation of surfactants molecules on the interface. To determine this fact, temporal evolution of interfacial tension and interfacial formation energy are studied and their temporal variations are correlated with cluster formation. To study cluster evolution, the mean cluster size and the probability that a molecule of surfactant chosen at random is free are obtained as a function of time. Cluster size distribution is estimated, and it is observed that some of the molecules remain free, whereas the rest agglomerate. Additionally, the temporal evolution of the interfacial thickness and the structure of the surfactant molecules on the interface are studied. It is observed how this structure depends on whether the molecules agglomerate or not.

Composition and process for enhanced oil recovery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Karas, L.J.

1988-04-12

A process for recovering crude oil from a subterranean formating having at least one injection means in fluid communication with at least one production means is described comprising: (a) injecting into the formation a liquid composition consisting essentially of at least one surfactant selected from surfactants having a formula RCH/sub 2/CH=C(R)CH/sub 2/O(CH/sub 2/CH/sub 2/O)/sub m/X, wherein R is C/sub 3/-C/sub 8/ alkyl, m is an integer from 1 to 10, and X is a sulfonate, sulfate, glyceryl sulfonate, or carboxylate anion neutralized by a sodium, potassium, or ammonium cation and an aqueous medium; (b) injecting a gas to urge themore » composition toward the production means, provided that the surfactant is present in an amount effective to reduce the mobility of the gas through the formation; and (c) recovering crude oil from the formation through the production means.« less

Stir bar sorptive extraction and liquid chromatography-tandem mass spectrometry determination of polar and non-polar emerging and priority pollutants in environmental waters.

PubMed

Aparicio, Irene; Martín, Julia; Santos, Juan Luis; Malvar, José Luis; Alonso, Esteban

2017-06-02

An analytical method based on stir bar sorptive extraction (SBSE) was developed and validated for the determination of environmental concern pollutants in environmental waters by liquid chromatography-tandem mass spectrometry (LC-MS/MS). Target compounds include six water and oil repellents (perfluorinated compounds), four preservatives (butylated hydroxytoluene and three parabens), two plasticizers (bisphenol A and di(2-ethylhexyl)phthalate), seven surfactants (four linear alkylbenzene sulfonates, nonylphenol and two nonylphenol ethoxylates), a flame retardant (hexabromocyclododecane), four hormones, fourteen pharmaceutical compounds, an UV-filter (2-ethylhexyl 4-methoxycinnamate) and nine pesticides. To achieve the simultaneous extraction of polar and non-polar pollutants two stir bar coatings were tested, the classic polydimethylsiloxane (PDMS) coating and the novel ethylene glycol modified silicone (EG-silicone). The best extraction recoveries were obtained using EG-silicone coating. The effects of sample pH, volume and ionic strength and extraction time on extraction recoveries were evaluated. The analytical method was validated for surface water and tap water samples. The method quantification limits ranged from 7.0ngL -1 to 177ngL -1 . The inter-day precision, expressed as relative standard deviation, was lower than 20%. Accuracy, expressed as relative recovery values, was in the range from 61 to 130%. The method was applied for the determination of the 48 target compounds in surface and tap water samples. Copyright © 2017 Elsevier B.V. All rights reserved.

Perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA) risk to beef consumers Part II: Adsorption, distribution, metabolism, and excretion studies for improving risk evaluations

USDA-ARS?s Scientific Manuscript database

Perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) are industrially produced chemicals used as surfactants and coatings in many industrial, commercial and consumer products. These compounds are ubiquitous in humans and the environment. PFOA and PFOS have been observed in biosolids fr...

Effects and risk assessment of linear alkylbenzene sulfonates in agricultural soil. 1. Short-term effects on soil microbiology.

PubMed

Elsgaard, L; Petersen, S O; Debosz, K

2001-08-01

Linear alkylbenzene sulfonates (LAS) may occur in sewage sludge that is applied to agricultural soil, in which LAS can be inhibitory to biological activity. As a part of a broader risk assessment of LAS in the terrestrial environment, we tested the short-term effects of aqueous LAS on microbial parameters in a sandy agricultural soil that was incubated for up to 11 d. The assays included 10 microbial soil parameters; ethylene degradation; potential ammonium oxidation; potential dehydrogenase activity; beta-glucosidase activity; iron reduction; the populations of cellulolytic bacteria, fungi and actinomycetes; the basal soil respiration; and the phospholipid fatty acid (PLFA) content. Except for beta-glucosidase activity, basal respiration, and total PLFA content, all soil parameters were sensitive to LAS, with EC10 values in the range of less than 8 to 22 mg/kg dry weight. This probably reflected a similar mode of LAS toxicity, ascribed to cell membrane interactions, and showed that sensitivity to LAS was common for various soil microorganisms. The extracellular beta-glucosidase activity was rather insensitive to LAS (ECI10, 47 mg/kg dry wt), whereas the basal soil respiration was not inhibited even at 793 mg/kg dry weight. This was interpreted as a combined response of inhibited and stimulated compartments of the microbial community. The PLFA content, surprisingly, showed no decrease even at 488 mg/kg. In conclusion, LAS inhibited specific microbial activities, although this could not be deduced from the basal respiration or the total PLFA content. The lowest EC10 values for microbial soil parameters were slightly higher than the predicted no-effect concentrations recently derived for plants and soil fauna (approximately 5 mg/kg dry wt).

Impact of model perfume molecules on the self-assembly of anionic surfactant sodium dodecyl 6-benzene sulfonate.

PubMed

Bradbury, Robert; Penfold, Jeffrey; Thomas, Robert K; Tucker, Ian M; Petkov, Jordan T; Jones, Craig; Grillo, Isabelle

2013-03-12

The impact of two model perfumes with differing degrees of hydrophobicity/hydrophilicity, linalool (LL) and phenylethanol (PE), on the solution structure of anionic surfactant sodium dodecyl 6-benzene sulfonate, LAS-6, has been studied by small angle neutron scattering, SANS. For both types of perfume molecules, complex phase behavior is observed. The phase behavior depends upon the concentration, surfactant/perfume composition, and type of perfume. The more hydrophilic perfume PE promotes the formation of more highly curved structures. At relatively low surfactant concentrations, small globular micelles, L1, are formed. These become perfume droplets, L(sm), stabilized by the surfactant at much higher perfume solution compositions. At higher surfactant concentrations, the tendency of LAS-6 to form more planar structures is evident. The more hydrophobic linalool promotes the formation of more planar structures. Combined with the greater tendency of LAS-6 to form planar structures, this results in the planar structures dominating the phase behavior for the LAS-6/linalool mixtures. For the LAS-6/linalool mixture, the self-assembly is in the form of micelles only at the lowest surfactant and perfume concentrations. Over most of the concentration-composition space explored, the structures are predominantly lamellar, L(α), or vesicle, L(v), or in the form of a lamellar/micellar coexistence. At low and intermediate amounts of LL, a significantly different structure is observed, and the aggregates are in the form of small, relatively monodisperse vesicles (i.e., nanovesicles), L(sv).

Enhanced waterflooding design with dilute surfactant concentrations for North Sea conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Michels, A.M.; Djojosoeparto, R.S.; Haas, H.

1996-08-01

Efficient selection procedures for surfactants have been applied to design a low-concentration surfactant-flooding process for North Sea oilfield application. Anionic surfactants of the propoxy ethoxy glyceryl sulfonate type can be used at 0.1 wt% concentrations together with sacrificial agents and without a polymer drive. Currently estimated unit technical costs (UTC`s)--at 8%--for application in the North Sea oil fields range frommore » $81 to $$94/incremental m{sup 3}, without taking uncertainty factors into account. Including such factors would likely add another $$31/m{sup 3} to the costs.« less

Expeditious Synthesis of Dianionic-Headed 4-Sulfoalkanoic Acid Surfactants.

PubMed

Jiang, Jianghui; Xu, Jiaxi

2017-04-16

4-Sulfoalkanoic acids are a class of important dianionic-headed surfactants. Various 4-sulfoalkanoic acids with straight C8, C10, C12, C14, C16, and C18 chains were synthesized expeditiously through the radical addition of methyl 2-((ethoxycarbonothioyl)thio)acetate to linear terminal olefins and subsequent oxidation with peroxyformic acid. This is a useful and convenient strategy for the synthesis of dianionic-headed surfactants with a carboxylic acid and sulfonic acid functionalities in the head group region.

Interaction of a digestive protease, Candida rugosa lipase, with three surfactants investigated by spectroscopy, molecular docking and enzyme activity assay.

PubMed

Zhang, Rui; Liu, Yang; Huang, Xinran; Xu, Mengchen; Liu, Rutao; Zong, Wansong

2018-05-01

The extensive use of surfactants in food, laundry products and agriculture has caused concern about their biosafety. However, few studies have been done on their potential effect on the lipase which has always been used with surfactants in food and laundry industry. Herein, we investigated the interaction of three surfactants (sodium dodecyl sulfate (SDS), sodium dodecyl benzene sulfonate (SDBS), sodium lauryl sulfonate (SLS)) with Candida rugosa lipase (CRL), which is a popular biocatalyst used regularly with surfactants. The effect of the three surfactants on the conformation and activity of CRL was evaluated by using multiple spectral methods, enzyme activity assay and molecular docking modeling. The results demonstrated that CRL interacted with SDS, SDBS and SLS primarily through hydrophobic forces, H-bonding and electrostatic forces, respectively. The binding constants (K A ) of SDBS with CRL varied with temperature: 1.99×10 3 mol/L at 298K and 4.13×10 3 mol/L at 318K. SDS and SDBS affected the secondary structure and skeleton of CRL, which changed the polarity of CRL and enhanced its activity. SLS also changed the secondary structure and activity of CRL moderately, but had little effect on its polarity and chromophore microenvironment. Accordingly, all three surfactants exhibited effect to CRL on the molecular level calling for more attention to pay on their biosafety. The work demonstrates that SDS, SDBS and SLS could cause negative effects to CRL from different angles and therefore are not bio-friendly detergents. Copyright © 2017 Elsevier B.V. All rights reserved.

An alternative approach to risk rank chemicals on the threat they pose to the aquatic environment.

PubMed

Johnson, Andrew C; Donnachie, Rachel L; Sumpter, John P; Jürgens, Monika D; Moeckel, Claudia; Pereira, M Gloria

2017-12-01

This work presents a new and unbiased method of risk ranking chemicals based on the threat they pose to the aquatic environment. The study ranked 12 metals, 23 pesticides, 11 other persistent organic pollutants (POPs), 13 pharmaceuticals, 10 surfactants and similar compounds and 2 nanoparticles (total of 71) of concern against one another by comparing their median UK river water and median ecotoxicity effect concentrations. To complement this, by giving an assessment on potential wildlife impacts, risk ranking was also carried out by comparing the lowest 10th percentile of the effects data with the highest 90th percentile of the exposure data. In other words, risk was pared down to just toxicity versus exposure. Further modifications included incorporating bioconcentration factors, using only recent water measurements and excluding either lethal or sub-lethal effects. The top ten chemicals, based on the medians, which emerged as having the highest risk to organisms in UK surface waters using all the ecotoxicity data were copper, aluminium, zinc, ethinylestradiol (EE2), linear alkylbenzene sulfonate (LAS), triclosan, manganese, iron, methomyl and chlorpyrifos. By way of contrast, using current UK environmental quality standards as the comparator to median UK river water concentrations would have selected 6 different chemicals in the top ten. This approach revealed big differences in relative risk; for example, zinc presented a million times greater risk then metoprolol and LAS 550 times greater risk than nanosilver. With the exception of EE2, most pharmaceuticals were ranked as having a relatively low risk. Copyright © 2017 Elsevier B.V. All rights reserved.

Fate and effects of linear alkylbenzene sulphonates (LAS) in the terrestrial environment.

PubMed

Jensen, J

1999-02-09

Linear alkylbenzene sulphonates (LAS) are a group of anionic surfactants, characterised by having both a hydrophobic and a hydrophilic group. LAS is one of the major ingredients of synthetic detergents and surfactants and is used world-wide for both domestic and industrial applications. LAS is relatively rapidly aerobically degraded, but only very slowly or not at all degraded under anaerobic conditions. Therefore, LAS can be found in very high concentrations in most sewage sludge and enter the soil compartment as a result of sludge application. LAS can be found in elevated concentrations in soil immediately after sludge amendment, but a half-life of approximately 1-3 weeks will generally prevent accumulation in soil and biota. The concentration in soils that have not received sewage sludge recently, is generally less than 1 mg kg-1 and not more than 5 mg LAS kg-1. This is below the lowest concentration of LAS where effects have been observed in the laboratory. The laboratory data is in accordance with field studies using aqueous solutions of the sodium salt of LAS. However, observations of the ecological impact of sewage sludge applications or application of LAS spiked into sludge indicates a lower toxicity of LAS when applied in sludge. On the basis of the information reviewed in this paper, it is concluded that LAS can be found in high concentrations in sewage sludge, but that the relatively rapid aerobic degradation and the reduced bioavailability when applied via sludge, most likely will prevent LAS from posing a threat to terrestrial ecosystems on a long term basis.

EFFECT OF INORGANIC CATIONS ON BACTERICIDAL ACTIVITY OF ANIONIC SURFACTANTS

PubMed Central

Voss, J. G.

1963-01-01

Voss, J. G. (Procter & Gamble Co., Cincinnati, Ohio). Effect of inorganic cations on bactericidal activity of anionic surfactants. J. Bacteriol. 86:207–211. 1963.—The bactericidal effectiveness of two alkyl benzene sulfonates and of three other types of anionic surfactants against Staphylococcus aureus is increased in the presence of low concentrations of divalent cations, especially alkaline earths and metals of group IIB of the periodic table. The cations may act by decreasing the negative charge at the cell surface and increasing adsorption of the surfactant anions, leading to damage to the cytoplasmic membrane and death of the cell. Increased adsorption of surfactant is also found with Escherichia coli, but does not lead to death of the cell. PMID:14058942

Kinetic and thermodynamic studies on the adsorption of anionic surfactant on quaternary ammonium cationic cellulose.

PubMed

Zhang, Yuanzhang; Shi, Wenjian; Zhou, Hualan; Fu, Xing; Chen, Xuan

2010-06-01

Removal of anionic surfactants from aqueous solutions by adsorption onto quaternary ammonium cationic cellulose (QACC) was investigated. The effects of solution acidity, initial concentration, adsorption time, and temperature on the adsorption of sodium dodecyl-benzene sulfonate (SDBS), sodium lauryl sulfate (SLS), and sodium dodecyl sulfonate (SDS) were studied. The kinetic experimental data fit well with the pseudo-second-order model; the rate constant of the adsorption increased with temperature. The values of apparent activation energy for the adsorption were calculated as ranging from 10.2 to 17.4 kJ/ mol. The adsorption isotherm can be described by the Langmuir isotherm. The values of thermodynamic parameters (deltaH0, deltaS0, and deltaG0) for the adsorption indicated that this process was spontaneous and endothermic. At 318 K, the saturated adsorption capacities of QACC for SDBS, SLS, and SDS were 1.75, 1.53, and 1.39 mmol/g, respectively. The adsorption process was mainly chemisorption and partially physisorption. The results show that QACC is effective for the removal of anionic surfactants.

Absorption properties of carbon dioxide enhanced-oil-recovery additives. Final Technical report, 12 May 1987-31 August 1989

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patton, J.T.; Holbrook, S.T.

1990-01-01

The selection of the optimum foaming agent (surfactant) for enhancing oil production by carbon dioxide flooding is based on foamability and adsorption. Measurement of adsorption on carbonate cores from New Mexico reservoirs showed large adsorption differences between three commercial, high-foaming surfactants. An ethoxylated alcohol structure was least adsorbed, 0.64 mg/cc pore volume; an ethoxylated alcohol sulfate was next, 0.74 mg/cc pore volume; the highest adsorbed was a glyceryl sulfonate, 2.30 mg/cc pore volume. Commercial application of the foaming additive involves injecting alternate slugs of surfactant solution and carbon dioxide. Surfactant concentration should be determined to allow for the adsorption above.

Spatial distribution of microbial biomass, activity, community structure, and the biodegradation of linear alkylbenzene sulfonate (LAS) and linear alcohol ethoxylate (LAE) in the subsurface.

PubMed

Federle, T W; Ventullo, R M; White, D C

1990-12-01

The vertical distribution of microbial biomass, activity, community structure and the mineralization of xenobiotic chemicals was examined in two soil profiles in northern Wisconsin. One profile was impacted by infiltrating wastewater from a laundromat, while the other served as a control. An unconfined aquifer was present 14 meters below the surface at both sites. Biomass and community structure were determined by acridine orange direct counts and measuring concentrations of phospholipid-derived fatty acids (PLFA). Microbial activity was estimated by measuring fluorescein diacetate (FDA) hydrolysis, thymidine incorporation into DNA, and mixed amino acid (MAA) mineralization. Mineralization kinetics of linear alkylbenzene sulfonate (LAS) and linear alcohol ethoxylate (LAE) were determined at each depth. Except for MAA mineralization rates, measures of microbial biomass and activity exhibited similar patterns with depth. PLFA concentration and rates of FDA hydrolysis and thymidine incorporation decreased 10-100 fold below 3 m and then exhibited little variation with depth. Fungal fatty acid markers were found at all depths and represented from 1 to 15% of the total PLFAs. The relative proportion of tuberculostearic acid (TBS), an actinomycete marker, declined with depth and was not detected in the saturated zone. The profile impacted by wastewater exhibited higher levels of PLFA but a lower proportion of TBS than the control profile. This profile also exhibited faster rates of FDA hydrolysis and amino acid mineralization at most depths. LAS was mineralized in the upper 2 m of the vadose zone and in the saturated zone of both profiles. Little or no LAS biodegradation occurred at depths between 2 and 14 m. LAE was mineralized at all depths in both profiles, and the mineralization rate exhibited a similar pattern with depth as biomass and activity measurements. In general, biomass and biodegradative activities were much lower in groundwater than in soil samples obtained from the same depth.

TOWARD A RISK ASSESSMENT OF PERFLUOROALKYL ACIDS

EPA Science Inventory

Perfluoroalkyl acids (PFAA) such as perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS),and fluorotelomer alcoholsare surfactants that have wide applications in industrial and consumer products. Various fluorotelomer alcohols are known to be metabolized to perfluo...

Novel star-like surfactant as dispersant for multi-walled carbon nanotubes in aqueous suspensions at high concentration

NASA Astrophysics Data System (ADS)

Qiao, Min; Ran, Qianping; Wu, Shishan

2018-03-01

A kind of novel surfactant with star-like molecular structure and terminated sulfonate was synthesized, and it was used as the dispersant for multi-walled carbon nanotubes (CNTs) in aqueous suspensions compared with a traditional single-chained surfactant. The star-like surfactant showed good dispersing ability for multi-walled CNTs in aqueous suspensions. Surface tension analysis, total organic carbon analysis, X-ray photoelectron spectroscopy, zeta potential, dynamic light scattering and transmission electron microscopy were performed to research the effect of star-like surfactant on the dispersion of multi-walled CNTs in aqueous suspensions. With the assistance of star-like surfactant, the CNTs could disperse well in aqueous suspension at high concentration of 50 g/L for more than 30 days, while the CNTs precipitated completely in aqueous suspension after 1 day without any dispersant or after 10 days with sodium 4-dodecylbenzenesulfonic acid as dispersant.

Adsorption properties of carbon dioxide enchanced oil recovery additives

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patton, J.T.; Holbrook, S.T.

1990-01-01

The selection of the optimum foaming agent (surfactant) for enhancing oil production by carbon dioxide flooding is based on foamability and adsorption. Measurements of adsorption on carbonate cores from New Mexico reservoirs showed large adsorption differences between three commercial, high-foaming surfactants. An ethoxylated alcohol structure was at least adsorbed, 0.64 mg/cc pore volume; an ethoxylated alcohol sulfate was next, 0.74 mg/cc pore volume; the highest adsorbed was a glyceryl sulfonate, 2.30 mg/cc pore volume. Commercial application of the foaming additive involves injecting alternate slugs of surfactant solution and carbon dioxide. Surfactant concentration should be determined to allow for the adsorptionmore » above. 9 refs., 27 figs., 6 tabs.« less

Effects of Surfactant on the Transport of Toxoplasma gondii in Saturated Sandy Porous Media: Experimental Tests and Modeling

NASA Astrophysics Data System (ADS)

Darnault, C. J. G.; Mutty, T.; L'Ollivier, C.; Dubey, J. P.; Aurélien, D.; Pullano, C. P.

2017-12-01

Understanding the transport of pathogens in the subsurface environment is essential for the risk assessment of groundwater contamination and the potential threat to human health. Currently, there is a lack of research in particular concerning the fate and transport of Toxoplasma gondii in porous media. The purpose of this research will be to characterize and model the transport and retention of Toxoplasma gondii in saturated silica-sand porous media in the presence of surfactant. Surfactants are chemicals commonly used as detergents and soaps, however they are able to impact flow properties in porous media and the interactions between surfaces, such as oocysts walls with sand grains. Therefore, we chose to characterize the changes that two surfactants have on the transport and fate of T. gondii. A total of 14 Column experiments were conducted including replicates as follows: 6 columns with an anionic-surfactant solution, 6 with a nonionic-surfactant solution, and 2 columns without surfactant to act as controls. All of the columns contained fine sand as the dominant grain size and each was run with a specified saturated flow rate in order to analyze the change with surfactant and disregard change as a result of a variation in the pore velocity. We chose to determine the retention and flow using the classic clean-bed colloid filtration model, and implemented sources for both adsorption and desorption of the particles which is known to happen on other biocolloids including oocysts. We implemented both Linear alkylbenzene sulphonic acid and Alkylphenol ethoxylate as our surfactants since they are the anionic and nonionic surfactants most commonly found in wastewater. Three different Critical Micelle Concentrations (CMC's) were run through the columns prior to the T. gondii oocysts injection followed by sequential injection of surfactant only and then deionized water only. The study compares the breakthrough of T. gondii with surfactant, without surfactant, as well as a the breakthrough of a bromide tracer. Each approach was modeled in addition to the experimentaltesting and we compared our results to previous microbe transport studies.

Adsorption of anionic surfactants from aqueous solution by high content of primary amino crosslinked chitosan microspheres.

PubMed

Zhang, Caihong; Wen, Haifeng; Huang, Yingying; Shi, Wenjian

2017-04-01

High content of primary amino crosslinked chitosan microspheres (ACCMs) were synthesized and characterized with IR, XRD and SEM technologies. Subsequently, ACCMs were adopted to adsorb three common anionic surfactants from aqueous solution: sodium dodecyl benzene sulfonate (SDBS), sodium lauryl sulfate (SLS), and sodium dodecyl sulfonate (SDS). The adsorption performances were evaluated based on different variables such as the pH, contact time, temperature and initial concentration of the anionic surfactants. Moreover, the adsorption were investigated with kinetic models, equilibrium isotherms and thermodynamic models. The experimental results indicated that the adsorption processes were fitted very well with a pseudo-second-order model. The adsorption isotherms could be better described by Langmuir model rather than Freundlich model. The adsorption of SDBS was a spontaneous, exothermic process. While the adsorption of SLS and SDS were spontaneous, endothermic. The adsorption processes were complex physical-chemistry adsorption models, which are dominated by physisorption. Furthermore, this study found that the material had strong absorption abilities for anionic surfactants, the saturation adsorption capacity of ACCMs were 1220mg/g for SDBS, 888mg/g for SLS, and 825mg/g for SDS at pH 3.0 and 298K, respectively. The adsorption capacity was reduced only 5.7% after 8 cycles of the adsorption-desorption processes. Copyright © 2017 Elsevier B.V. All rights reserved.

Novel fluorinated surfactants tentatively identified in firefighters using liquid chromatography quadrupole time-of-flight tandem mass spectrometry and a case-control approach.

PubMed

Rotander, Anna; Kärrman, Anna; Toms, Leisa-Maree L; Kay, Margaret; Mueller, Jochen F; Gómez Ramos, María José

2015-02-17

Fluorinated surfactant-based aqueous film-forming foams (AFFFs) are made up of per- and polyfluorinated alkyl substances (PFAS) and are used to extinguish fires involving highly flammable liquids. The use of perfluorooctanesulfonic acid (PFOS) and other perfluoroalkyl acids (PFAAs) in some AFFF formulations has been linked to substantial environmental contamination. Recent studies have identified a large number of novel and infrequently reported fluorinated surfactants in different AFFF formulations. In this study, a strategy based on a case-control approach using quadrupole time-of-flight tandem mass spectrometry (QTOF-MS/MS) and advanced statistical methods has been used to extract and identify known and unknown PFAS in human serum associated with AFFF-exposed firefighters. Two target sulfonic acids [PFOS and perfluorohexanesulfonic acid (PFHxS)], three non-target acids [perfluoropentanesulfonic acid (PFPeS), perfluoroheptanesulfonic acid (PFHpS), and perfluorononanesulfonic acid (PFNS)], and four unknown sulfonic acids (Cl-PFOS, ketone-PFOS, ether-PFHxS, and Cl-PFHxS) were exclusively or significantly more frequently detected at higher levels in firefighters compared to controls. The application of this strategy has allowed for identification of previously unreported fluorinated chemicals in a timely and cost-efficient way.

Developmental Toxicity of Perfluorinated Phosphonic Acids in Mice

EPA Science Inventory

Perfluorinated phosphonic acids (PFPAs) are a third member of the perfluoroalkyl acid (PFAA) family, and are structurally similar to the perfluoroalkyl sulfonates and perfluoroalkyl carboxylates. PFPAs are used primarily as a surfactant defoaming agent in pesticide production. Re...

Influences of surfactants on the preparation of copper nanoparticles by electron beam irradiation

NASA Astrophysics Data System (ADS)

Zhou, Ruimin; Wu, Xinfeng; Hao, Xufeng; Zhou, Fei; Li, Hongbin; Rao, Weihong

2008-02-01

Electron beam radiation was applied to prepare nano-size copper in water system using polyvinyl alcohol, sodium dodecyl benzene sulfonate, gluten and polyethylene glycol as the surfactants, respectively. The irradiated products were characterized by XRD, TEM and LSPSDA. The XRD and TEM showed that relative pure copper products with an average size of 20 nm, 40 nm and 20 nm can be obtained by using gluten, PEG and SDBS as surfactant, respectively. An admixture of copper and cuprous oxide was obtained in PVA system. The LSPSDA showed that the size of the Cu nanoparticles decreased with increasing the glutin concentration.

Gene expression profiling in the lung and liver of PFOS-exposed mouse fetuses

EPA Science Inventory

The industrial surfactants perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA) are persistent environmental contaminants commonly found in the tissues of humans and wildlife. Both compounds are agonists of peroxisome proliferator-activated receptor α (PPARα) and...

The role of groundwater chemistry in the transport of bacteria to water-supply wells

USGS Publications Warehouse

Harvey, R.W.; Metge, D.W.

1999-01-01

Static mini-columns and in situ injection and recovery tests were used to assess the effects of modest changes in groundwater chemistry upon the pH-dependence of bacterial attachment, a primary determinant of bacterial mobility in drinking water aquifers. In uncontaminated groundwater (<1 mg l-1 dissolved organic carbon, DOC), bacterial attachment to aquifer grain surfaces declined steadily from 93 to 20% in response to an increase in pH from 5.8 to 7.8. However, bacterial attachment in modestly-contaminated groundwater (4 mg l-1 DOC) was relatively insensitive to pH change from pH 3.5 to pH 8, as was bacterial attachment in uncontaminated groundwater amended with only ~3 mg l-1 of purified humic acid. Destruction by UV-oxidation of the DOC in contaminated groundwater partially restored the pH-dependence of bacterial attachment. Results from static column tests and from a small-scale (3.6 m) natural-gradient injection and recovery study suggest that low concentrations of surfactants can also substantively alter the attraction of groundwater bacteria for grain surfaces and, therefore can alter the transport of bacteria to water-supply wells. This phenomenon was pH-sensitive and dependent upon the nature of the surfactant. At pH 7.6, 200 mg l-1 of the non-ionic surfactant, Imbentin, caused a doubling of fractional bacterial attachment in aquifer-sediment columns, but had little effect under slightly acidic conditions (e.g. at pH 5.8). In contrast, 1 mg l-1 of linear alkylbenzene sulphonate (LAS) surfactant, a common sewage-derived contaminant, decreased the fractional bacterial attachment by more than 30% at pH 5.8, but had little effect at pH 7.3.Static mini-columns and in situ injection and recovery tests were used to assess the effects of modest changes in groundwater chemistry upon the pH-dependence of bacterial attachment, a primary determinant of bacterial mobility in drinking water aquifers. In uncontaminated groundwater (<1 mg l-1 dissolved organic carbon, DOC), bacterial attachment to aquifer grain surfaces declined steadily from 93 to 20% in response to an increase in pH from 5.8 to 7.8. However, bacterial attachment in modestly-contaminated groundwater (4 mg l-1 DOC) was relatively insensitive to pH change from pH 3.5 to pH 8, as was bacterial attachment in uncontaminated groundwater amended with only approx. 3 mg l-1 of purified humic acid. Destruction of UV-oxidation of the DOC in contaminated groundwater partially restored the pH-dependence of bacterial attachment. Results from the static column tests and from a small-scale (3.6 m) natural-gradient injection and recovery study suggest that low concentrations of surfactants can also substantively alter the attraction of groundwater bacteria for grain surfaces and, therefore can alter the transport of bacteria to water-supply wells. This phenomenon was pH-sensitive and dependent upon the nature of the surfactant. At pH 7.6, 200 mg l-1 of the non-ionic surfactant, Imbentin, caused a doubling of fractional bacterial attachment in aquifer-sediment columns, but had little effect under slightly acidic conditions (e.g. at pH 5.8). In contrast, 1 mg l-1 of linear alkylbenzene sulphonate (LAS) surfactant, a common sewage-derived contaminant, decreased the fractional bacterial attachment by more than 30% at pH 5.8, but had little effect at pH 7.3.

Synergism and Physicochemical Properties of Anionic/Amphoteric Surfactant Mixtures with Nonionic Surfactant of Amine Oxide Type

NASA Astrophysics Data System (ADS)

Blagojević, S. M.; Pejić, N. D.; Blagojević, S. N.

2017-12-01

The physicochemical properties of initial formulation, that is anionic/amphoteric surfactants mixture SLES/AOS/CAB (sodium lauryl ether sulfate (SLES), α-olefin sulfonates (AOS) and cocamidopropyl betaine (CAB) at ratio 80 : 15 : 5) with nonionic surfactant of amine oxide type (lauramine oxide (AO)) in various concentration (1-5%) were studied. To characterize the surfactants mixture, the critical micelle concentration (CMC), surface tension (γ), foam volume, biodegradability and irritability were determined. This study showed that adding of AO in those mixtures lowered both γ and CMC as well as enhanced SLES/AOS/CAB foaming properties, but did not significantly affect biodegradability and irritability of initial formulation. Moreover, an increase in AO concentration has a meaningful synergistic effect on the initial formulation properties. All those results indicates that a nonionic surfactant of amine oxide type significantly improves the performance of anionic/amphoteric mixed micelle systems, and because of that anionic/amphoteric/nonionic mixture can be used in considerably lower concentrations as a cleaning formulation.

Molecular dynamics study of intermediate phase of long chain alkyl sulfonate/water systems.

PubMed

Poghosyan, Armen H; Arsenyan, Levon H; Shahinyan, Aram A

2013-01-08

Using atomic level simulation we aimed to investigate various intermediate phases of the long chain alkyl sulfonate/water system. Overall, about 800 ns parallel molecular dynamics simulation study was conducted for a surfactant/water system consisting of 128 sodium pentadecyl sulfonate and 2251 water molecules. The GROMACS software code with united atom force field was applied. Despite some differences, the analysis of main structural parameters is in agreement with X-ray experimental findings. The mechanism of self-assembly of SPDS molecules was also examined. At T = 323 K we obtained both tilted fully interdigitated and liquid crystalline-like disordered hydrocarbon chains; hence, the presence of either gel phase that coexists with a lamellar phase or metastable gel phase with fraction of gauche configuration can be assumed. Further increase of temperature revealed that the system underwent a transition to a lamellar phase, which was clearly identified by the presence of fully disordered hydrocarbon chains. The transition from gel-to-fluid phase was implemented by simulated annealing treatment, and the phase transition point at T = 335 K was identified. The surfactant force field in its presented set is surely enabled to fully demonstrate the mechanism of self-assembly and the behavior of phase transition making it possible to get important information around the phase transition point.

The impact of electrolyte on the adsorption of the anionic surfactant methyl ester sulfonate at the air-solution interface: Surface multilayer formation.

PubMed

Xu, H; Thomas, R K; Penfold, J; Li, P X; Ma, K; Welbourne, R J L; Roberts, D W; Petkov, J T

2018-02-15

The methyl ester sulfonates represent a promising group of anionic surfactants which have the potential for improved performance and biocompatibility in a range of applications. Their solution properties, in particular their tolerance to hard water, suggests that surface ordering may occur in the presence of multi-valent counterion. Understanding their adsorption properties in a range of different circumstances is key to the exploitation of their potential. Neutron reflectivity and surface tension have been used to characterise the adsorption at the air-aqueous solution interface of the anionic surfactant sodium tetradecanoic 2-sulfo 1-methyl ester, C 14 MES, in the absence of electrolyte and in the presence of mono, di, and tri-valent counterions, Na + , Ca 2+ , and Al 3+ . In particular the emphasis has been on exploring the tendency to form layered structures at the interface. In the absence of electrolyte and in the presence of NaCl and CaCl 2 and AlCl 3 at low concentrations monolayer adsorption is observed, and the addition of electrolyte results in enhanced adsorption. In the presence of NaCl and CaCl 2 only monolayer adsorption is observed. However at higher AlCl 3 concentrations surface multilayer formation is observed, in which the number of bilayers at the surface depends upon the surfactant and AlCl 3 concentrations. Copyright © 2017 Elsevier Inc. All rights reserved.

Improved detergent-based recovery of polyhydroxyalkanoates (PHAs).

PubMed

Yang, Yung-Hun; Brigham, Christopher; Willis, Laura; Rha, ChoKyun; Sinskey, Anthony

2011-05-01

Extracting polyhydroxyalkanoate (PHA) polymer from bacterial cells often involves harsh conditions, including use of environmentally harmful solvents. We evaluated different detergents under various conditions to extract PHA from Ralstonia eutropha and Escherichia coli cells. Most detergents tested recovered highly pure PHA polymer from cells in amounts that depended on the percentage of polymer present in the cell. Detergents such as linear alkylbenzene sulfonic acid (LAS-99) produced a high yield of high purity polymer, and less detergent was needed compared to the amount of SDS to produce comparable yields. LAS-99 also has the advantage of being biodegradable and environmentally safe. Chemical extraction of PHA with detergents could potentially minimize or eliminate the need to use harsh organic solvents, thus making industrial PHA production a cleaner technology process. © Springer Science+Business Media B.V. 2011

Performance and characterization of a new tannin-based coagulant

NASA Astrophysics Data System (ADS)

Beltrán-Heredia, J.; Sánchez-Martín, J.; Gómez-Muñoz, C.

2012-09-01

Diethanolamine and formaldehyde were employed to cationize tannins from black wattle. This novel coagulant called CDF was functionally characterized in removing sodium dodecylbenzene sulfonate (anionic surfactant) and Palatine Fast Black WAN (azoic dye). Refined tannin-derived commercial coagulants exhibited similar efficiency, while CDF presented higher coagulant ability than alum, a usual coagulant agent. Low doses of CDF (ca. 100 mg L-1) were able to remove more than 70 % of surfactant and more than 85 % of dye (initial pollutant concentration of ca. 100 mg L-1) and it presented no temperature affection and worked at a relatively wide pH range. Surfactant and dye removal responded to the classical coagulant-and-adsorption models, such as Frumkin-Fowler-Guggenheim or Gu and Zhu in the case of surfactant, and Langmuir and Freundlich in the case of dye.

Nanoparticle-enabled delivery of surfactants in porous media.

PubMed

Nourafkan, Ehsan; Hu, Zhongliang; Wen, Dongsheng

2018-06-01

The adsorption of surfactants on the reservoir rocks surface is a serious issue in many energy and environment related areas. Learning from the concept of drug delivery in the nano-medicine field, this work proposes and validates the concept of using nanoparticles to deliver a mixture of surfactants into a porous medium. TiO 2 nanoparticles (NPs) are used as carriers for a blend of surfactants mixtures including anionic alkyl aryl sulfonic acid (AAS) and nonionic alcohol ethoxylated (EA) at the optimum salinity and composition conditions. The transport of NPs through a core sample of crushed sandstone grains and the adsorption of surfactants are evaluated. By using TiO 2 NPs, the adsorption of surfactant molecules can be significantly reduced, i.e. half of the initial adsorption value. The level of surfactant adsorption reduction is related to the NPs transport capability through the porous medium. An application study shows that comparing to surfactant flooding alone, the total oil recovery can be increased by 7.81% of original oil in place (OOIP) by using nanoparticle bonded surfactants. Such work shows the promise of NP as an effective surfactant carrier for sandstone reservoirs, which could have many potential applications in enhanced oil recovery (EOR) and environmental remediation. Copyright © 2018 Elsevier Inc. All rights reserved.

iMAST Quarterly, Number 3, 2003

DTIC Science & Technology

2003-01-01

alcohol 5–10% Trade secret surfactant 5–10% Trade secret organic acid 1–5% Trade secret surfactant 1–5% Sodium lauryl sulfate 20–48% Non-hazardous...ingredients Atofina TURCO 6776 Thin 35–65% Water 10–20% Benzyl alcohol 10–15% Formic acid 10–15% Sodium xylene sulfonate 10–15% Hydrotreated petroleum...distillates Atofina TURCO 4181L 65–75% Water 20–30% Sodium hydroxide 5–10% Triethanolamine 5–10% Sodium gluconate Atofina TURCO 5668 40–50% N-Methyl-2

Implications of surfactant-induced flow for miscible-displacement estimation of air-water interfacial areas in unsaturated porous media.

PubMed

Costanza-Robinson, Molly S; Zheng, Zheng; Henry, Eric J; Estabrook, Benjamin D; Littlefield, Malcolm H

2012-10-16

Surfactant miscible-displacement experiments represent a conventional means of estimating air-water interfacial area (A(I)) in unsaturated porous media. However, changes in surface tension during the experiment can potentially induce unsaturated flow, thereby altering interfacial areas and violating several fundamental method assumptions, including that of steady-state flow. In this work, the magnitude of surfactant-induced flow was quantified by monitoring moisture content and perturbations to effluent flow rate during miscible-displacement experiments conducted using a range of surfactant concentrations. For systems initially at 83% moisture saturation (S(W)), decreases of 18-43% S(W) occurred following surfactant introduction, with the magnitude and rate of drainage inversely related to the surface tension of the surfactant solution. Drainage induced by 0.1 mM sodium dodecyl benzene sulfonate, commonly used for A(I) estimation, resulted in effluent flow rate increases of up to 27% above steady-state conditions and is estimated to more than double the interfacial area over the course of the experiment. Depending on the surfactant concentration and the moisture content used to describe the system, A(I) estimates varied more than 3-fold. The magnitude of surfactant-induced flow is considerably larger than previously recognized and casts doubt on the reliability of A(I) estimation by surfactant miscible-displacement.

Use of anionic surfactants for selective polishing of silicon dioxide over silicon nitride films using colloidal silica-based slurries

NASA Astrophysics Data System (ADS)

Penta, Naresh K.; Amanapu, H. P.; Peethala, B. C.; Babu, S. V.

2013-10-01

Four different anionic surfactants, sodium dodecyl sulfate, dodecyl benzene sulfonic acid (DBSA), dodecyl phosphate and Sodium lauroyl sarcosine, selected from the sulfate, phosphate, and carboxylic family, were investigated as additives in silica dispersions for selective polishing of silicon dioxide over silicon nitride films. We found that all these anionic surfactants suppress the nitride removal rates (RR) for pH ≤4 while more or less maintaining the oxide RRs, resulting in high oxide-to-nitride RR selectivity. The RR data obtained as a function of pH were explained based on pH dependent distributions of surfactant species, change in the zeta potentials of oxide and nitride surfaces, and thermogravimetric data. It appears that the negatively charged surfactant species preferentially adsorb on the positively charged nitride surface below IEP through its electrostatic interactions and form a bilayer adsorption, resulting in the suppression of nitride RRs. In contrast to the surfactants, K2SO4 interacts only weakly with the nitride surface and hence cannot suppress its RR.

Lactoferrin denaturation induced by anionic surfactants: The role of the ferric ion in the protein stabilization.

PubMed

Ferreira, Gabriel Max Dias; Ferreira, Guilherme Max Dias; Agudelo, Álvaro Javier Patiño; Hudson, Eliara Acipreste; Dos Santos Pires, Ana Clarissa; da Silva, Luis Henrique Mendes

2018-05-11

Here, investigation was made of the interaction between Lactoferrin (Lf) and the anionic surfactants sodium dodecyl sulfate (SDS), sodium dodecylbenzene sulfonate (SDBS), and sodium decyl sulfate (DSS), using isothermal titration calorimetry, Nano differential scanning calorimetry (NanoDSC), and fluorescence spectroscopy. The Lf-surfactant interaction was enthalpically favorable (the integral enthalpy change ranged from -5.99 kJ mol -1 , for SDS at pH 3.0, to -0.61 kJ mol -1 , for DSS at pH 12.0) and promoted denaturation of the protein. The Lf denaturation efficiency followed the order DSS < SDS < SDBS. The extent of binding of the surfactants to Lf strongly depended on pH and the surfactant structure, reaching a maximum value of 505 SDBS molecules per gram of Lf at pH 3.0. The different efficiencies of the surfactants in denaturing Lf were attributed to the balance of hydrophobic and electrostatic interactions, which also depended on pH and the surfactant structure, highlighting the SDBS-tryptophan residue specific interaction, where SDBS acted as a quencher of fluorescence. Interestingly, the NanoDSC and fluorescence measurements showed that the ferric ion bound to Lf increased its stability against denaturation induced by the surfactants. The results have important implications for understanding the influence of surfactants on structural changes in metalloproteins. Copyright © 2017. Published by Elsevier B.V.

New Class of Amphiphiles Designed for Use in Water-in-Supercritical CO2 Microemulsions.

PubMed

Sagisaka, Masanobu; Ogiwara, Shunsuke; Ono, Shinji; James, Craig; Yoshizawa, Atsushi; Mohamed, Azmi; Rogers, Sarah E; Heenan, Richard K; Yan, Ci; Peach, Jocelyn Alice; Eastoe, Julian

2016-11-29

Water-in-supercritical CO 2 microemulsions formed using the hybrid F-H surfactant sodium 1-oxo-1-[4-(perfluorohexyl)phenyl]hexane-2-sulfonate, FC6-HC4, have recently been shown to have the highest water-solubilizing power ever reported. FC6-HC4 demonstrated the ability to outperform not only other surfactants but also other FCm-HCn analogues containing different fluorocarbon and hydrocarbon chain lengths (Sagisaka, M. et al. Langmuir 2015, 31, 7479-7487). With the aim of clarifying the key structural features of this surfactant, this study examined the phase behavior and water/supercritical CO 2 aggregate formation of 1-oxo-1-[4-(perfluorohexyl)phenyl]hexane (Nohead FC6-HC4), which is an FC6-HC4 analogue but now, interestingly, without the sulfonate headgroup. Surprisingly, Nohead FC6-HC4, which would not normally be identified as a classic surfactant, yielded transparent single-phase W/CO 2 microemulsions with polar cores able to solubilize a water-soluble dye, even at pressures and temperatures so low as to approach the critical point of CO 2 (e.g., ∼100 bar at 35 °C). High-pressure small-angle scattering (SANS) measurements revealed the transparent phases to consist of ellipsoidal nanodroplets of water. The morphology of these droplets was shown to be dependent on the pressure, Nohead FC6-HC4 concentration, and water-to-surfactant molar ratio. Despite having almost the same structure as Nohead FC6-HC4, analogues containing both shorter and longer hydrocarbons were unable to form W/CO 2 microemulsion droplets. This shows the importance of the role of the hydrocarbon chain in the stabilization of W/CO 2 microemulsions. A detailed examination of the mechanism of Nohead FC6-HC4 adsorption onto the water surface suggests that the hexanoyl group protrudes into the aqueous core, allowing for association between the carbonyl group and water.

Enhanced dispersion of multiwall carbon nanotubes in natural rubber latex nanocomposites by surfactants bearing phenyl groups.

PubMed

Mohamed, Azmi; Anas, Argo Khoirul; Bakar, Suriani Abu; Ardyani, Tretya; Zin, Wan Manshol W; Ibrahim, Sofian; Sagisaka, Masanobu; Brown, Paul; Eastoe, Julian

2015-10-01

Here is presented a systematic study of the dispersibility of multiwall carbon nanotubes (MWCNTs) in natural rubber latex (NR-latex) assisted by a series of single-, double-, and triple-sulfosuccinate anionic surfactants containing phenyl ring moieties. Optical polarising microscopy, field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and Raman spectroscopy have been performed to obtain the dispersion-level profiles of the MWCNTs in the nanocomposites. Interestingly, a triple-chain, phenyl-containing surfactant, namely sodium 1,5-dioxo-1,5-bis(3-phenylpropoxy)-3-((3-phenylpropoxy)carbonyl) pentane-2-sulfonate (TCPh), has a greater capacity the stabilisation of MWCNTs than a commercially available single-chain sodium dodecylbenzenesulfonate (SDBS) surfactant. TCPh provides significant enhancements in the electrical conductivity of nanocomposites, up to ∼10(-2) S cm(-1), as measured by a four-point probe instrument. These results have allowed compilation of a road map for the design of surfactant architectures capable of providing the homogeneous dispersion of MWCNTs required for the next generation of polymer-carbon-nanotube materials, specifically those used in aerospace technology. Copyright © 2015 Elsevier Inc. All rights reserved.

Mass spectrometry compatible surfactant for optimized in-gel protein digestion.

PubMed

Saveliev, Sergei V; Woodroofe, Carolyn C; Sabat, Grzegorz; Adams, Christopher M; Klaubert, Dieter; Wood, Keith; Urh, Marjeta

2013-01-15

Identification of proteins resolved by SDS-PAGE depends on robust in-gel protein digestion and efficient peptide extraction, requirements that are often difficult to achieve. A lengthy and laborious procedure is an additional challenge of protein identification in gel. We show here that with the use of the mass spectrometry compatible surfactant sodium 3-((1-(furan-2-yl)undecyloxy)carbonylamino)propane-1-sulfonate, the challenges of in-gel protein digestion are effectively addressed. Peptide quantitation based on stable isotope labeling showed that the surfactant induced 1.5-2 fold increase in peptide recovery. Consequently, protein sequence coverage was increased by 20-30%, on average, and the number of identified proteins saw a substantial boost. The surfactant also accelerated the digestion process. Maximal in-gel digestion was achieved in as little as one hour, depending on incubation temperature, and peptides were readily recovered from gel eliminating the need for postdigestion extraction. This study shows that the surfactant provides an efficient means of improving protein identification in gel and streamlining the in-gel digestion procedure requiring no extra handling steps or special equipment.

Influence of surfactants on the morphology of SnO{sub 2} nanocrystals prepared via a hydrothermal method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang Mi; Shanghai Institute of Ceramics; Gao Yanfeng, E-mail: yfgao@mail.sic.ac.cn

2012-05-15

Nanoscaled SnO{sub 2} with different morphologies has been synthesized via a simple hydrothermal process at 180 Degree-Sign C using polyvinylpyrrolidone (PVP), sodium dodecyl sulfonate (SDS), cetyl trimethyl ammonium bromide (CTAB) or tetrapropyl ammonium bromide (TPAB) as surfactant. All the prepared SnO{sub 2} are of a tetragonal crystal structure. Nanocubes, nanorods, nanosheets, nanobelts and nanoparticles were prepared when changing the type and dosage of organic surfactants. It is shown that anionic surfactant (SDS) and cationic surfactant (CTAB or TPAB) at their suitable addition amounts can largely influence the morphologies of SnO{sub 2} nanocrystals. The effect is significantly dependent on the solventmore » types: water or ethanol. The non-ionic surfactant (PVP) can also change the morphologies like SDS but the impacts are less obvious. The effect of surfactants on the shape and size of SnO{sub 2} nanoparticles was discussed in detail. The particle growth mechanism is described based on the electrostatic interactions and Van der Waals' forces. - Graphical abstract: SnO{sub 2} nanocrystals with controllable morphologies were prepared via a hydrothermal method with surfactants. Highlights: Black-Right-Pointing-Pointer SnO{sub 2} nanocrystals were prepared via a hydrothermal method with surfactants. Black-Right-Pointing-Pointer SnO{sub 2} morphologies changed with the type and the dosage of surfactants. Black-Right-Pointing-Pointer The effect of surfactants on the growth of crystal planes was studied. Black-Right-Pointing-Pointer The controlling mechanisms of surfactants on SnO{sub 2} morphologies were discussed.« less

Food web modeling of a river ecosystem for risk assessment of down-the-drain chemicals: a case study with AQUATOX.

PubMed

Lombardo, Andrea; Franco, Antonio; Pivato, Alberto; Barausse, Alberto

2015-03-01

Conventional approaches to estimating protective ecotoxicological thresholds of chemicals, i.e. predicted no-effect concentrations (PNEC), for an entire ecosystem are based on the use of assessment factors to extrapolate from single-species toxicity data derived in the laboratory to community-level effects on ecosystems. Aquatic food web models may be a useful tool to improve the ecological realism of chemical risk assessment because they enable a more insightful evaluation of the fate and effects of chemicals in dynamic trophic networks. A case study was developed in AQUATOX to simulate the effects of the anionic surfactant linear alkylbenzene sulfonate and the antimicrobial triclosan on a lowland riverine ecosystem. The model was built for a section of the River Thames (UK), for which detailed ecological surveys were available, allowing for a quantification of energy flows through the whole ecosystem. A control scenario was successfully calibrated for a simulation period of one year, and tested for stability over six years. Then, the model ecosystem was perturbed with varying inputs of the two chemicals. Simulations showed that both chemicals rapidly approach steady-state, with internal concentrations in line with the input bioconcentration factors throughout the year. At realistic environmental concentrations, both chemicals have insignificant effects on biomass trends. At hypothetical higher concentrations, direct and indirect effects of chemicals on the ecosystem dynamics emerged from the simulations. Indirect effects due to competition for food sources and predation can lead to responses in biomass density of the same magnitude as those caused by direct toxicity. Indirect effects can both exacerbate or compensate for direct toxicity. Uncertainties in key model assumptions are high as the validation of perturbed simulations remains extremely challenging. Nevertheless, the study is a step towards the development of realistic ecological scenarios and their potential use in prospective risk assessment of down-the-drain chemicals. Copyright © 2014 Elsevier B.V. All rights reserved.

Study on the reutilization of clear fracturing flowback fluids in surfactant flooding with additives for Enhanced Oil Recovery (EOR).

PubMed

Dai, Caili; Wang, Kai; Liu, Yifei; Fang, Jichao; Zhao, Mingwei

2014-01-01

An investigation was conducted to study the reutilization of clear fracturing flowback fluids composed of viscoelastic surfactants (VES) with additives in surfactant flooding, making the process more efficient and cost-effective. The clear fracturing flowback fluids were used as surfactant flooding system with the addition of α-olefin sulfonate (AOS) for enhanced oil recovery (EOR). The interfacial activity, emulsification activity and oil recovery capability of the recycling system were studied. The interfacial tension (IFT) between recycling system and oil can be reduced by 2 orders of magnitude to 10(-3) mN/m, which satisfies the basic demand of surfactant flooding. The oil can be emulsified and dispersed more easily due to the synergetic effect of VES and AOS. The oil-wet surface of quartz can be easily converted to water-wet through adsorption of surfactants (VES/AOS) on the surface. Thirteen core plug flooding tests were conducted to investigate the effects of AOS concentrations, slug sizes and slug types of the recycling system on the incremental oil recovery. The investigations prove that reclaiming clear fracturing flowback fluids after fracturing operation and reuse it in surfactant flooding might have less impact on environment and be more economical.

Study on the Reutilization of Clear Fracturing Flowback Fluids in Surfactant Flooding with Additives for Enhanced Oil Recovery (EOR)

PubMed Central

Dai, Caili; Wang, Kai; Liu, Yifei; Fang, Jichao; Zhao, Mingwei

2014-01-01

An investigation was conducted to study the reutilization of clear fracturing flowback fluids composed of viscoelastic surfactants (VES) with additives in surfactant flooding, making the process more efficient and cost-effective. The clear fracturing flowback fluids were used as surfactant flooding system with the addition of α-olefin sulfonate (AOS) for enhanced oil recovery (EOR). The interfacial activity, emulsification activity and oil recovery capability of the recycling system were studied. The interfacial tension (IFT) between recycling system and oil can be reduced by 2 orders of magnitude to 10−3 mN/m, which satisfies the basic demand of surfactant flooding. The oil can be emulsified and dispersed more easily due to the synergetic effect of VES and AOS. The oil-wet surface of quartz can be easily converted to water-wet through adsorption of surfactants (VES/AOS) on the surface. Thirteen core plug flooding tests were conducted to investigate the effects of AOS concentrations, slug sizes and slug types of the recycling system on the incremental oil recovery. The investigations prove that reclaiming clear fracturing flowback fluids after fracturing operation and reuse it in surfactant flooding might have less impact on environment and be more economical. PMID:25409507

Oxidative desulfurization of dibenzothiophene with molecular oxygen using emulsion catalysis.

PubMed

Lü, Hongying; Gao, Jinbo; Jiang, Zongxuan; Yang, Yongxing; Song, Bo; Li, Can

2007-01-14

Dibenzothiophene (DBT) is oxidized to the corresponding sulfoxide and sulfone in an emulsion system (W/O) composed of polyoxometalate anion [C(18)H(37)N(CH(3))3](5)[PV(2)Mo(10)O(40)] as both the surfactant and catalyst, using molecular oxygen as the oxidant and aldehyde as the sacrificial agent under mild conditions.

LAS bioconcentration is isomer specific

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tolls, J.; Haller, M.; Graaf, I. de

1995-12-31

The authors measured parent compound specific bioconcentration data for linear alkylbenzene sulfonates in Pimephales promelas. They did so by using cold, custom synthesized sulfophenyl alkanes. They observed that, within homologous series of isomers, the uptake rate constants (k{sub 1}) and the bioconcentration factor (BCF) increase with increasing number of carbon atoms in the alkyl chain (n{sub C-atoms}). In contrast, the elimination rate constant k{sub 2} appears to be independent of the alkyl chain length. Regressions of log BCF vs n{sub C-atoms} yielded different slopes for the homologous groups of the 5- and the 2-sulfophenyl alkane isomers. Regression of all logmore » BCF-data vs log 1/CMC yielded a good description of the data. However, when regressing the data for both homologous series separately again very different slopes are obtained. The results therefore indicate that hydrophobicity-bioconcentration relationships may be different for different homologous groups of sulfophenyl alkanes.« less

Nature and transformation of dissolved organic matter in treatment wetlands

USGS Publications Warehouse

Barber, L.B.; Leenheer, J.A.; Noyes, T.I.; Stiles, E.A.

2001-01-01

This investigation into the occurrence, character, and transformation of dissolved organic matter (DOM) in treatment wetlands in the western United States shows that (i) the nature of DOM in the source water has a major influence on transformations that occur during treatment, (ii) the climate factors have a secondary effect on transformations, (iii) the wetlands receiving treated wastewater can produce a net increase in DOM, and (iv) the hierarchical analytical approach used in this study can measure the subtle DOM transformations that occur. As wastewater treatment plant effluent passes through treatment wetlands, the DOM undergoes transformation to become more aromatic and oxygenated. Autochthonous sources are contributed to the DOM, the nature of which is governed by the developmental stage of the wetland system as well as vegetation patterns. Concentrations of specific wastewaterderived organic contaminants such as linear alkylbenzene sulfonate, caffeine, and ethylenediaminetetraacetic acid were significantly attenuated by wetland treatment and were not contributed by internal loading.

Automated electronic tongue based on potentiometric sensors for the determination of a trinary anionic surfactant mixture.

PubMed

Cortina, Montserrat; Ecker, Christina; Calvo, Daniel; del Valle, Manuel

2008-01-22

An automated electronic tongue consisting of an array of potentiometric sensors and an artificial neural network (ANN) has been developed to resolve mixtures of anionic surfactants. The sensor array was formed by five different flow-through sensors for anionic surfactants, based on poly(vinyl chloride) membranes having cross-sensitivity features. Feedforward multilayer neural networks were used to predict surfactant concentrations. As a great amount of information is required for the correct modelling of the sensors response, a sequential injection analysis (SIA) system was used to automatically provide it. Dodecylsulfate (DS(-)), dodecylbenzenesulfonate (DBS(-)) and alpha-alkene sulfonate (ALF(-)) formed the three-analyte study case resolved in this work. Their concentrations varied from 0.2 to 4mM for ALF(-) and DBS(-) and from 0.2 to 5mM for DS(-). Good prediction ability was obtained with correlation coefficients better than 0.933 when the obtained values were compared with those expected for a set of 16 external test samples not used for training.

Silver Nanoparticles Synthesized Using Caesalpinia sappan Extract as Potential Novel Nanoantibiotics Against Methicillin-Resistant Staphylococcus aureus.

PubMed

Jun, Sang Hui; Cha, Song-Hyun; Kim, Jae-Hyun; Yoon, Minho; Cho, Seonho; Park, Youmie

2015-08-01

Silver nanoparticles (AgNPs) have been shown to be effective antibacterial agents against methicillin-resistant Staphylococcus aureus (MRSA). In this study, AgNPs were synthesized using Caesalpinia sappan extract as a reducing agent to convert Ag+ to AgNPs. Seven stabilizers (surfactants and polymers) were added during the reduction step to increase the colloidal stability and to enhance the antibacterial activity of the AgNPs. Spherical and amorphous particles were primarily observed, with estimated diameters ranging from 30.2 to 47.5 nm. X-ray diffraction confirmed the face centered cubic structures of the AgNPs. Among the employed stabilizers, the cationic surfactant cetyltrimethylammonium bromide (CTAB) exhibited the highest antibacterial activity against 19 strains of MRSA, followed by polyvinylpyrrolidone (PVP, average molecular weight of 10,000). In contrast, the anionic surfactants sodium dodecyl sulfate (SDS) and sodium dodecylbenzene sulfonate (NaDDBS) did not exhibit any significant antibacterial activity, suggesting that the cationic surfactant head group contributed to the higher antibacterial activity of the AgNPs against MRSA.

Polyelectrolyte-Surfactant Complexes: A New Class of Organogelators

NASA Astrophysics Data System (ADS)

Cavicchi, Kevin; Liu, Yuqing; Guzman, Gustavo

2011-03-01

Polyelectrolyte-surfactant complexes (PE-SURFs) are a class of polymers generated by neutralizing a polyelectrolyte with an oppositely charged surfactant. It has been found that PE-SURFs composed of polystyrene sulfonate and long chain alkyl dimethyl amines act as good organogelators for a range of hydrophobic, organic solvents. Thermo-reversible organogels are formed by heating and cooling PE-SURF/solvent solutions. The gel transition temperature is influenced by the degree of polymerization, the length of the alkyl side-chain, the solubility parameter of the solvent, and the concentration of the gelator. Freeze-drying and scanning electron microscopy characterization of the resultant xerogels shows the formation of rod- and plate-like network morphologies depending on the system parameters. This behavior is consistent with gelation driven by the self-assembly of the amphiphilic PE-SURFs into micellar networks.

Efficient removal of perfluorooctane sulfonate from aqueous film-forming foam solution by aeration-foam collection.

PubMed

Meng, Pingping; Deng, Shubo; Maimaiti, Ayiguli; Wang, Bin; Huang, Jun; Wang, Yujue; Cousins, Ian T; Yu, Gang

2018-07-01

Aqueous film-forming foams (AFFFs) used in fire-fighting are one of the main contamination sources of perfluorooctane sulfonate (PFOS) to the subterranean environment, requiring high costs for remediation. In this study, a method that combined aeration and foam collection was presented to remove PFOS from a commercially available AFFF solution. The method utilized the strong surfactant properties of PFOS that cause it to be highly enriched at air-water interfaces. With an aeration flow rate of 75 mL/min, PFOS removal percent reached 96% after 2 h, and the PFOS concentration in the collected foam was up to 6.5 mmol/L, beneficial for PFOS recovery and reuse. Increasing the aeration flow rate, ionic strength and concentration of co-existing surfactant, as well as decreasing the initial PFOS concentration, increased the removal percents of PFOS by increasing the foam volume, but reduced the enrichment of PFOS in the foams. With the assistance of a co-existing hydrocarbon surfactant, PFOS removal percent was above 99.9% after aeration-foam collection for 2 h and the enrichment factor exceeded 8400. Aeration-foam collection was less effective for short-chain perfluoroalkyl substances due to their relatively lower surface activity. Aeration-foam collection was found to be effective for the removal of high concentrations of PFOS from AFFF-contaminated wastewater, and the concentrated PFOS in the collected foam can be reused. Copyright © 2018 Elsevier Ltd. All rights reserved.

Anisotropic reversed micelles with fluorocarbon-hydrocarbon hybrid surfactants in supercritical CO2.

PubMed

Sagisaka, Masanobu; Ono, Shinji; James, Craig; Yoshizawa, Atsushi; Mohamed, Azmi; Guittard, Frédéric; Enick, Robert M; Rogers, Sarah E; Czajka, Adam; Hill, Christopher; Eastoe, Julian

2018-08-01

Previous work (M. Sagisaka, et al. Langmuir 31 (2015) 7479-7487), showed the most effective fluorocarbon (FC) and hydrocarbon (HC) chain lengths in the hybrid surfactants FCm-HCn (sodium 1-oxo-1-[4-(perfluoroalkyl)phenyl]alkane-2-sulfonates, where m = FC length and n = HC length) were m and n = 6 and 4 for water solubilization, whereas m 6 and n 6, or m 6 and n 5, were optimal chain lengths for reversed micelle elongation in supercritical CO 2 . To clarify why this difference of only a few methylene chain units is so effective at tuning the solubilizing power and reversed micelle morphology, nanostructures of water-in-CO 2 (W/CO 2 ) microemulsions were investigated by high-pressure small-angle neutron scattering (SANS) measurements at different water-to-surfactant molar ratios (W 0 ) and surfactant concentrations. By modelling SANS profiles with cylindrical and ellipsoidal form factors, the FC6-HCn/W/CO 2 microemulsions were found to increase in size with increasing W 0 and surfactant concentration. Ellipsoidal cross-sectional radii of the FC6-HC4/W/CO 2 microemulsion droplets increased linearly with W 0 , and finally reached ∼39 Å and ∼78 Å at W 0  = 85 (close to the upper limit of solubilizing power). These systems appear to be the largest W/CO 2 microemulsion droplets ever reported. The aqueous domains of FC6-HC6 rod-like reversed micelles increased in size by 3.5 times on increasing surfactant concentration from 35 mM to 50 mM: at 35 mM, FC6-HC5 formed rod-like reversed micelles 5.3 times larger than FC6-HC6. Interestingly, these results suggest that hybrid HC-chains partition into the microemulsion aqueous cores with the sulfonate headgroups, or at the W/CO 2 interfaces, and so play important roles for tuning the W/CO 2 interfacial curvature. The super-efficient W/CO 2 -type solubilizer FC6-HC4, and the rod-like reversed micelle forming surfactant FC6-HC5, represent the most successful cases of low fluorine content additives. These surfactants facilitate VOC-free, effective and energy-saving CO 2 solvent systems for applications such as extraction, dyeing, dry cleaning, metal-plating, enhanced oil recovery and organic/inorganic or nanomaterial synthesis. Copyright © 2017 Elsevier B.V. All rights reserved.

Influence of linear alkylbenzene sulfonate (LAS) on the structure of Alphaproteobacteria, Actinobacteria, and Acidobacteria communities in a soil microcosm.

PubMed

Sánchez-Peinado, M del Mar; González-López, Jesús; Martínez-Toledo, M Victoria; Pozo, Clementina; Rodelas, Belén

2010-03-01

Linear alkylbenzene sulfonate (LAS) is the most used anionic surfactant in a worldwide scale and is considered a high-priority pollutant. LAS is regarded as a readily biodegradable product under aerobic conditions in aqueous media and is mostly removed in wastewater treatment plants, but an important fraction (20-25%) is immobilized in sewage sludge and persists under anoxic conditions. Due to the application of the sludge as a fertilizer, LAS reaches agricultural soil, and therefore, microbial toxicity tests have been widely used to evaluate the influence of LAS on soil microbial ecology. However, molecular-based community-level analyses have been seldom applied in studies regarding the effects of LAS on natural or engineered systems, and, to our knowledge, there are no reports of their use for such appraisals in agricultural soil. In this study, a microcosm system is used to evaluate the effects of a commercial mixture of LAS on the community structure of Alphaproteobacteria, Actinobacteria, and Acidobacteria in an agricultural soil. The microcosms consisted of agricultural soil columns (800 g) fed with sterile water (8 ml h(-1)) added of different concentration of LAS (10 or 50 mg l(-1)) for periods of time up to 21 days. Sterile water was added to control columns for comparison. The structures of Alphaproteobacteria, Actinobacteria, and Acidobacteria communities were analyzed by a cultivation independent method (temperature gradient gel electrophoresis (TGGE) separation of polymerase chain reaction (PCR)-amplified partial 16S rRNA genes). Relevant populations were identified by subsequent reamplification, DNA sequencing, and database comparisons. Cluster analysis of the TGGE fingerprints taking into consideration both the number of bands and their relative intensities revealed that the structure of the Alphaproteobacteria community was significantly changed in the presence of LAS, at both concentrations tested. The average number of bands was significantly lower in the microcosms receiving 50 mg l(-1) LAS and in the lower portion of soil cores. The clear differentiation of the samples of the upper portion of the soil columns amended with LAS was specifically related to the presence and intensity of a distinctive major band (named band class 7). There was a statistically significant positive correlation between the concentrations of LAS detected in soil portions taken from LAS 10 mg l(-1) and LAS 50 mg l(-1) microcosms and the relative intensity of band class 7 in the corresponding TGGE profiles. Prevalent Alphaproteobacteria populations in the soil microcosms had close similarity (>99%) to cultivated species affiliated to genera of the Rhizobiaceae, Methylocystaceae, Hyphomicrobiaceae, Rhodospirillaceae, Brucellaceae, Bradyrhizobiaceae, and Caulobacteraceae families. The population represented by band class 7 was found closely related to the genus Phenylobacterium (Caulobacteraceae). According to cluster analysis of TGGE profiles, the structure of both Actinobacteria and Acidobacteria communities in the soil microcosms was remarkably stable in the presence of LAS at the two concentrations tested, as most bands were universally present in all samples and displayed fairly similar relative intensities. Previous studies by others authors, based on biological and chemical tests, concluded that LAS toxicity was not an important microbial selection factor in sludge amended soil, while work based on the use of molecular fingerprinting to evaluate the impact of LAS in aqueous media and marine sediments showed that concentrations as low as 1 mg l(-1) significantly influence the development of the bacterial community structure. Although TGGE is not a strictly quantitative method due to the bias introduced by the PCR reaction, changes of band intensity through experiments are a consequence of a change in the relative abundance of the corresponding populations in the community and can be used as a semiquantitative measure of bacterial diversity. Our results evidence that the Phenylobacterium population represented by band class 7 was favored by the presence of increasing concentrations of LAS in the soil and turned into a dominant population, suggesting its possible ability to use LAS in soil as a source of nutrients. As studies with pure cultures are required to confirm the ability of this population to degrade LAS, isolation strategies are currently under development in our laboratory. The weak effect of LAS on the structure of Actinobacteria and Acidobacteria communities is particularly interesting, as to our knowledge, there are no previous reports regarding the effects of LAS on these bacterial groups in soil. CONCLUSIONS, RECOMMENDATIONS, AND PERSPECTIVES: The Phenylobacterium-related alphaproteobacterial population identified in this work was selectively enriched in LAS polluted soil and is a plausible candidate to play a relevant role in the biotransformation of the surfactant under the conditions tested. The surfactant had no remarkable effects on the Actinobacteria and Acidobacteria fingerprints in soil, even when present at concentrations widely exceeding those reached in soil immediately after sludge application. TGGE fingerprinting provides a reliable and low time-consuming method for the monitoring of the bacterial community structure and dynamics, and we recommend its integration with the biological and chemical analyses usually applied in risk assessment of LAS in the environment.

Rapid analysis of perchlorate in drinking water at parts per billion levels using microchip electrophoresis.

PubMed

Gertsch, Jana C; Noblitt, Scott D; Cropek, Donald M; Henry, Charles S

2010-05-01

A microchip capillary electrophoresis (MCE) system has been developed for the determination of perchlorate in drinking water. The United States Environmental Protection Agency (USEPA) recently proposed a health advisory limit for perchlorate in drinking water of 15 parts per billion (ppb), a level requiring large, sophisticated instrumentation, such as ion chromatography coupled with mass spectrometry (IC-MS), for detection. An inexpensive, portable system is desired for routine online monitoring applications of perchlorate in drinking water. Here, we present an MCE method using contact conductivity detection for perchlorate determination. The method has several advantages, including reduced analysis times relative to IC, inherent portability, high selectivity, and minimal sample pretreatment. Resolution of perchlorate from more abundant ions was achieved using zwitterionic, sulfobetaine surfactants, N-hexadecyl-N,N-dimethyl-3-ammonio-1-propane sulfonate (HDAPS) and N-tetradecyl-N,N-dimethyl-3-ammonio-1-propane sulfonate (TDAPS). The system performance and the optimization of the separation chemistry, including the use of these surfactants to resolve perchlorate from other anions, are discussed in this work. The system is capable of detection limits of 3.4 +/- 1.8 ppb (n = 6) in standards and 5.6 +/- 1.7 ppb (n = 6) in drinking water.

The effects of anionic and non-ionic surfactant on anaerobic co-digestion of sludge, food wastes and green wastes.

PubMed

Sun, Jian; Zhang, Yuchi; Pan, Xiaofang; Zhu, Gefu

2018-03-05

Surfactants are widely used and discharged into wastewater treatment plants, which might influence the anaerobic digestion (AD) treatment of municipal waste. In this study, the effects of typical anionic surfactants sodium dodecyl benzene6 sulfonate (SDBS) and non-ionic surfactants APG, on mesophilic anaerobic co-digestion of sludge, food waste, and green waste were investigated. Results indicated that at 5 mg/g, the biogas production was inhibited in SDBS supplemented systems while stimulated in APG-added reactors, with the methane yield of 146.58 L/g VS consumed. At 15 mg/g, the biogas production in both SDBS and APG supplemented reactors was both inhibited. It means the negative or positive effect of APG on AD depends on the dose of APG supplementation. The 16S rRNA gene analysis demonstrated the microbial community structure in the digester was changed due to the addition of surfactant. Bacteroidia significantly increased with the addition of APG and SBDS, while the increase of Clostridia only occurred in APG-added system. The variation of microbial Communities' structure in APG and SDBS-added digesters might give an explanation for the different efficiencies in these two systems. Thus, the effects of surfactants on the efficiency of AD should be considered during the disposal of municipal organic waste.

Synthesis and application of surfactants coated magnetite nanoparticles for demulsification of crude oil in water emulsion

NASA Astrophysics Data System (ADS)

Yau, Xin Hui; Khe, Cheng Seong; Liu, Wei Wen; Lai, Chin Wei; Oo, Zeya

2017-10-01

Magnetite nanoparticles were synthesized through co-precipitation method, in which surfactant such as polyvinylpyrrolidone (PVP) and sodium dodecyl benzene sulfonate (SDBS) were applied as stabilizing agent. Various techniques were employed to characterize the synthesized magnetite nanoparticles. Magnetite nanoparticles with spinel structure are successfully synthesized and confirmed by X-ray diffraction (XRD). X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) results proved that surface of magnetite nanoparticles were successfully coated with PVP and SDBS. From the transmission electron microscope (TEM), it showed that surfactant coated magnetite nanoparticles possess smaller particle size than that of bare magnetite nanoparticles. In comparison with SDBS, PVP has a better capping efficiency and the PVP coated magnetite nanoparticles have an average particle size of 10.8 nm. In addition, surfactant coated magnetite nanoparticles also exhibited lower value of saturation magnetization (Ms). Lower value of Ms might be attributed to the small sized nanoparticles. All magnetite nanoparticles synthesized with and without surfactant showed superparamagnetic behaviour. Bare and surfactant coated magnetite nanoparticles have been utilized as a demulsifier for crude oil in water emulsion. Those nanoparticles that produced using SDBS (ED= 87%) showed higher efficiency than that of PVP coated (ED=80%) and bare magnetite nanoparticles (ED=85%) in demulsification tests.

Increasing maturity of kerogen type II reflected by alkylbenzene distribution from pyrolysis-gas chromatography-mass spectrometry

USGS Publications Warehouse

Lis, G.P.; Mastalerz, Maria; Schimmelmann, A.

2008-01-01

A series of Late Devonian to Early Mississippian type II kerogens with vitrinite reflectance values Ro 0.29-2.41% were analyzed using py-GC-MS. In addition, a low maturity kerogen with Ro 0.44% was separated into fractions via density gradient centrifugation, followed by py-GC-MS of the alginite and amorphinite maceral concentrates. Alkylbenzenes and n-alk-1-ene/n-alkane doublets represented the main compound classes identified in all pyrolysates. The pyrolysate from alginite featured 1,2,4-trimethylbenzene and toluene as the two most prominent alkylbenzenes. In contrast, alkylbenzenes in pyrolysates from amorphinite and low maturity bulk kerogens with Ro 0.29-0.63% were dominated by 1,2,3,4-tetramethylbenzene. With increasing thermal maturity, pyrolysates were increasingly dominated by (i) alkylbenzenes with fewer methyl groups, namely by tri- and dimethylbenzenes at medium maturity (Ro 0.69-1.19%), and (ii) by toluene at higher maturity (Ro 1.30-2.41%). With increasing maturity of kerogen type II, the decreasing abundance of highly methyl-substituted alkylbenzenes and the parallel increase in less methyl-substituted alkylbenzenes in flash pyrolysates suggest that demethylation is an important chemical process in the thermal maturation of kerogen type II. ?? 2008 Elsevier Ltd. All rights reserved.

Effect of surfactants on Ra-sHSPI - A small heat shock protein from the cattle tick Rhipicephalus annulatus

NASA Astrophysics Data System (ADS)

Siddiqi, Mohammad Khursheed; Shahein, Yasser E.; Hussein, Nahla; Khan, Rizwan H.

2016-09-01

Electrostatic interaction plays an important role in protein aggregation phenomenon. In this study, we have checked the effect of anionic - Sodium Dodecyl Sulfate (SDS) and cationic-Cetyltrimethyl Ammonium Bromide (CTAB) surfactant on aggregation behavior of Ra-sHSPI, a small heat shock protein purified from Rhipicephalus annulatus tick. To monitor the effect of these surfactants, we have employed several spectroscopic methods such as Rayleigh light scattering measurements, ANS (8-Anilinonaphthalene-1-sulfonic acid) fluorescence measurements, ThT (Thioflavin T) binding assays, Far-UV CD (Circular Dichroism) and dynamic light scattering measurements. In the presence of anionic surfactant-SDS, Ra-sHSPI forms amyloid fibrils, in contrast, no amyloid formation was observed in presence of cationic surfactant at low pH. Enhancement of ANS fluorescence intensity confirms the exposition of more hydrophobic patches during aggregation. ThT binding assay confirms the amyloid fibrillar nature of the SDS induced Ra-sHSPI aggregates and supported by PASTA 2.0 (prediction of amyloid structural aggregation) software. This study demonstrates the crucial role of charge during amyloid fibril formation at low pH in Ra-sHSPI.

Competitive substrate biodegradation during surfactant-enhanced remediation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Goudar, C.; Strevett, K.; Grego, J.

The impact of synthetic surfactants on the aqueous phase biodegradation of benzene, toluene, and p-xylene (BTpX) was studied using two anionic surfactants, sodium dodecyl sulfate (SDS) and sodium dodecyl benzene sulfonate (SDBS), and two nonionic surfactants, POE(20) sorbitan monooleate (T-maz-80) and octyl-phenolpoly(ethyleneoxy) ethanol (CA-620). Batch biodegradation experiments were performed to evaluate surfactant biodegradability using two different microbial cultures. Of the four surfactants used in this study, SDS and T-maz-80 were readily degraded by a microbial consortium obtained from an activated sludge treatment system, whereas only SDS was degraded by a microbial culture that was acclimated to BTpX. Biodegradation kinetic parametersmore » associated with SDS and T-maz-80 degradation by the activated sludge consortium were estimated using respirometric data in conjunction with a nonlinear parameter estimation technique as {mu}{sub max} = 0.93 h{sup {minus}1}, K{sub s}= 96.18 mg/L and {mu}{sub max} = 0.41 h{sup {minus}1}, K{sub s} = 31.92 mg/L, respectively. When both BTpX and surfactant were present in the reactor along with BTpX-acclimated microorganisms, two distinct biodegradation patterns were seen. SDS was preferentially utilized inhibiting hydrocarbon biodegradation, whereas, the other three surfactants had no impact on BTpX biodegradation. None of the four surfactants were toxic to the microbial cultures used in this study. Readily biodegradable surfactants are not very effective for subsurface remediation applications as they are rapidly consumed, and also because of their potential inhibitory effects on intrinsic hydrocarbon biodegradation. This greatly increases treatment costs as surfactant recovery and reuse are adversely affected.« less

Electroactive Self-Assembled Monolayers Detect Micelle Formation.

PubMed

Dionne, Eric R; Badia, Antonella

2017-02-15

The interfacial electrochemistry of self-assembled monolayers (SAMs) of ferrocenyldodecanethiolate on gold (FcC 12 SAu) electrodes is applied to detect the micellization of some common anionic surfactants, sodium n-alkyl sulfates, sodium n-alkyl sulfonates, sodium diamyl sulfosuccinate, and sodium dodecanoate, in aqueous solution by cyclic voltammetry. The apparent formal redox potential (E°' SAM ) of the FcC 12 SAu SAM is used to track changes in the concentration of the unaggregated surfactant anions and determine the critical micelle concentration (cmc). The effect of added salt (NaF) on the sodium alkyl sulfate concentration dependence of E°' SAM is also investigated. Weakly hydrated anions, such as ClO 4 - , pair with the electrogenerated SAM-bound ferroceniums to neutralize the excess positive charge created at the SAM/electrolyte solution interface and stabilize the oxidized cations. E°' SAM exhibits a Nernstian-type dependence on the anion activity in solution. Aggregation of the surfactant anions into micelles above the cmc causes the free surfactant anion activity to deviate from the molar concentration of added surfactant, resulting in a break in the plot of E°' SAM versus the logarithm of the concentration of anionic surfactant. The concentration at which this deviation occurs is in good agreement with literature or experimentally determined values of the cmc. The effects of Ohmic potential drop, liquid junction potential, and surfactant adsorption behavior on E°' SAM are addressed. Ultimately, the E°' SAM response as a function of the anionic surfactant concentration exhibits the same features reported using potentiometry and surfactant ion-selective electrodes, which provide a direct measure of the free surfactant anion activity, thus making FcC 12 SAu SAM electrodes useful for the detection of surfactant aggregation and micelle formation.

Effect of linear alkylbenzene mixtures and sanitary sewage in biochemical and molecular responses in pacific oyster Crassostrea gigas.

PubMed

Flores-Nunes, Fabrício; Mattos, Jacó J; Zacchi, Flávia L; Serrano, Miguel A S; Piazza, Clei E; Sasaki, Silvio T; Taniguchi, Satie; Bicego, Márcia C; Melo, Cláudio M R; Bainy, Afonso C D

2015-11-01

Urban effluents are rich in nutrients, organic matter, pharmaceuticals and personal care products (PPCPs), pesticides, hydrocarbons, surfactants, and others. Previous studies have shown that oysters Crassostrea gigas accumulate significant levels of linear alkylbenzenes (LABs) in sanitary sewage contaminated sites, but there is little information about its toxicological effects in marine bivalves. The aim of this study was to analyze the transcription of genes in two tissues of C. gigas exposed for 12, 24, and 36 h to LABs or sanitary sewage. Likewise, the activity of antioxidant and biotransformation enzymes was measured in oysters exposed for 36 h in all groups. Oysters exposed to LABs and oysters exposed to sanitary sewage showed different patterns of transcriptional responses. LAB-exposed oysters showed lower level of biological responses than the oysters exposed to sanitary sewage. Despite the ability of the oyster C. gigas to accumulate LABs (28-fold), the data indicate that these contaminants are not the cause for the transcriptional responses observed in oysters exposed to sanitary sewage. Possibly, the biological changes observed in the sanitary sewage-exposed oysters are associated with the presence of other contaminants, which might have caused synergistic, additive, or antagonistic effects. The results show that FABP-like and GST-ω-like messenger RNAs (mRNAs) have a rapid response in tissues of oyster C. gigas exposed to sanitary sewage, suggesting a possible protective response and a role in maintaining homeostasis of these organisms.

Modulation of the wettability of excipients by surfactant and its impacts on the disintegration and release of tablets.

PubMed

Yang, Baixue; Xu, Lu; Wang, Qiuxiao; Li, Sanming

2016-12-01

To investigate the modulation of the wettability of excipients by different types of surfactants and its impacts on the disintegration of tablets and drug release. The critical micelle concentration (CMC) of surfactants, including sodium dodecyl sulfate (SDS), sodium dodecyl benzene sulfonate (SDBS), dodecyl trimethyl ammonium bromide (DTAB), cetyltrimethyl ammonium bromide (CTAB) and polysorbate (Tween-20 and Tween-80), was obtained using the platinum ring method. Contact angles of surfactant solutions on the excipient compacts and double-distilled water on the mixture of surfactant and the other excipient (magnesium stearate (MgSt) or sodium alginate (SA)) were measured by the sessile drop technique. Besides, surface free energy of excipients was calculated by the Owens method. Finally, the disintegration of tablets and in vitro dissolution testing were performed according to the method described in USP. The wettability of excipients could be enhanced to different extent with low concentration of surfactant solutions and maintained stable basically after CMC. For MgSt (hydrophobic excipient), the shorter the hydrophobic chain (C 12 , including SDS and DTAB), the better the wettability with the addition of surfactant in the formulation, leading to the shorter disintegration time of tablets and higher drug release rate. In contrast, the wettability of SA (hydrophilic excipient) was reduced by adding surfactant, resulting in the longer disintegration time of tablets and lower release rate. The modulation of the wetting of pharmaceutical excipients by surfactant had changed the disintegration time of tablets and drug release rate to a greater extent.

Sulfonated mesoporous silica-carbon composites and their use as solid acid catalysts

NASA Astrophysics Data System (ADS)

Valle-Vigón, Patricia; Sevilla, Marta; Fuertes, Antonio B.

2012-11-01

The synthesis of highly functionalized porous silica-carbon composites made up of sulfonic groups attached to a carbon layer coating the pores of three types of mesostructured silica (i.e. SBA-15, KIT-6 and mesocellular silica) is presented. The synthesis procedure involves the following steps: (a) removal of the surfactant, (b) impregnation of the silica pores with a carbon precursor, (c) carbonization and (d) sulfonation. The resulting silica-carbon composites contain ˜30 wt % of carbonaceous matter with a high density of acidic groups attached to the deposited carbon (i.e.sbnd SO3H, sbnd COOH and sbnd OH). The structural characteristics of the parent silica are retained in the composite materials, which exhibit a high surface area, a large pore volume and a well-ordered porosity made up uniform mesopores. The high density of the sulfonic groups in combination with the mesoporous structure of the composites ensures that a large number of active sites are easily accessible to reactants. These sulfonated silica-carbon composites behave as eco-friendly, active, selective, water tolerant and recyclable solid acids. In this study we demonstrate the usefulness of these composites as solid acid catalysts for the esterification of maleic anhydride, succinic acid and oleic acid with ethanol. These composites exhibit a superior intrinsic catalytic activity to other commercial solid acids such as Amberlyst-15.

Removal of anionic surfactant sodium dodecyl benzene sulfonate (SDBS) from wastewaters by zero-valent iron (ZVI): predominant removal mechanism for effective SDBS removal.

PubMed

Takayanagi, Akari; Kobayashi, Maki; Kawase, Yoshinori

2017-03-01

Mechanisms for removal of anionic surfactant sodium dodecyl benzene sulfonate (SDBS) in wastewaters by zero-valent iron (ZVI) were systematically examined. The contributions of four removal mechanisms, i.e., reductive degradation, oxidative degradation, adsorption, and precipitation, changed significantly with solution pH were quantified and the effective removal of SDBS by ZVI was found to be attributed to the adsorption capability of iron oxides/hydroxides on ZVI surface at nearly neutral pH instead of the degradation at acidic condition. The fastest SDBS removal rate and the maximum TOC (total organic carbon) removal efficiency were obtained at pH 6.0. The maximum TOC removal at pH 6.0 was 77.8%, and the contributions of degradation, precipitation, and adsorption to TOC removal were 4.6, 14.9, and 58.3%, respectively. At pH 3.0, which is an optimal pH for oxidative degradation by the Fenton reaction, the TOC removal was only 9.8% and the contributions of degradation, precipitation, and adsorption to TOC removal were 2.3, 4.6, and 2.9%, respectively. The electrostatic attraction between dodecyl benzene sulfate anion and the iron oxide/hydroxide layer controlled the TOC removal of SDBS. The kinetic model based on the Langmuir-Hinshelwood/Eley-Rideal approach could successfully describe the experimental results for SDBS removal by ZVI with the averaged correlation coefficient of 0.994. ZVI was found to be an efficient material toward the removal of anionic surfactant at nearly neutral pH under the oxic condition.

Effectiveness of the Surfactant Dioctyl Sodium Sulfosuccinate (DOSS) to Disperse Oil in a Changing Marine Environment

NASA Astrophysics Data System (ADS)

Steffy, D. A.; Nichols, A.; Kiplagat, G.

2011-12-01

We investigated the surfactant which was used to disperse the oil spill which occurred in the Gulf of Mexico during the summer 2010. The surfactant DOSS is an organic sulfonic acid salt which is a synthetic detergent that disrupts the interfacial tension between the saltwater and crude oil phases. The disruption becomes maximum at or above the critical micelle concentration (CMC). The CMC for the surfactant was determined to be at 0.13 % solution in deionized water at a pH of 7.2 and a temperature of 70oF. The CMC is lower at 0.09% solution in salt water. The effect has been identified as a "salting out" effect (Somasundaran, 2006). The CMC of DOSS in both saline and deionized water occurred at lower percent solutions at higher temperatures. The surface tension versus % solution plots are modeled by a power equation, with correlation coefficients consistently over 0.94. Surface tension versus percent solution plots are scalable to fit a temperature desired by the function f(x)= (1/(1+X^α)), where α = T1/T2.

The role of electrolyte and polyelectrolyte on the adsorption of the anionic surfactant, sodium dodecylbenzenesulfonate, at the air-water interface.

PubMed

Zhang, X L; Taylor, D J F; Thomas, R K; Penfold, J

2011-04-15

The role of the polyelectrolyte, poly(ethyleneimine), PEI, and the electrolytes NaCl and CaCl(2), on the adsorption of the anionic surfactant, sodium dodecylbenzenesulfonate, LAS, at the air-water interface have been investigated by neutron reflectivity and surface tension. The surface tension data for the PEI/LAS mixtures are substantially affected by pH and the addition of electrolyte, and are consistent with a strong adsorption of surface polymer/surfactant complexes down to relatively low surfactant concentrations. The effects are most pronounced at high pH, and this is confirmed by the adsorption data obtained directly from neutron reflectivity. However, the effects of the addition of PEI and electrolyte on the LAS adsorption are not as pronounced as previously reported for PEI/SDS mixtures. This is attributed primarily to the steric hindrance of the LAS phenyl group resulting in a reduction in the ion-dipole attraction between the LAS sulfonate and amine groups that dominates the interaction at high pH. Copyright © 2011 Elsevier Inc. All rights reserved.

A comparative sonochemical reaction that is independent of the intensity of ultrasound and the geometry of the exposure apparatus.

PubMed

Sostaric, Joe Z

2008-09-01

Sonolysis of aqueous solutions of n-alkyl anionic surfactants results in the formation of secondary carbon-centered radicals (-*CH-). The yield of -*CH- depends on the bulk surfactant concentration up to a maximum attainable radical yield (the 'plateau yield') where an increasing surfactant concentration (below the critical micelle concentration) no longer affects the -*CH- yield. In an earlier study it was found that the ratio of -*CH- detected following sonolysis of aqueous solutions of sodium pentane sulfonate (SPSo) to that of sodium dodecyl sulfate (SDS) (i.e. CH(SPSo)/CH(SDS)) depended on the frequency of sonolysis, but was independent of the ultrasound intensity, at the plateau concentrations [J.Z. Sostaric, P. Riesz, Adsorption of surfactants at the gas/solution interface of cavitation bubbles: an ultrasound intensity-independent frequency effect in sonochemistry, J. Phys. Chem. B 106 (2002) 12537-12548]. In the current study, it was found that the CH(SPSo)/CH(SDS) ratio depended only on the ultrasound frequency and did not depend on the geometry of the ultrasound exposure apparatus considered.

Effect of linear alkylbenzene sulphonate (LAS) on the mineralization, metabolism and uptake of 14C-phenanthrene in a model ecosystem (water-lava-plant-air).

PubMed

Jiang, Xia; Yediler, Ayfer; Yufang, Song; Sun, Tieheng; Kettrup, Antonius

2005-11-01

The aim of this work was to evaluate the effect of linear alkylbenzene sulfonate (LAS, 200 mg l(-1)) on the fate of phenanthrene in a model ecosystem "water-lava-hydrophytes-air". The experiments were conducted using two closed cultivation chamber systems. Rushes (Juncus effesus) were selected as a representative hydrophyte. Five hundred micrograms per liter of phenanthrene in a culture solution containing a 14C-activity of 75 microCi per chamber was applied (i) to investigate the degradation of the labeled test substance and the transfer processes within the system; (ii) to determine the mass-balance possible and (iii) to detect the occurrence of volatile test substances, their volatile metabolites and the degradation end-product CO2 in the gas phase. Most of the applied 14C-activity was found in the plant (41-45%), in which approximately 95% was associated with plant roots and approximately 5% with shoots. The 14C-activity recovered in the form of VOCs and CO2 was measured in lava (18-29%, 8-11%), and in the culture solution (10-14% and 1%), respectively. Majority of the applied 14C-activity existed in two forms, i.e. (1) polar metabolites (26%), of which 91% were found in plant roots, and (2) un-extractable residues (23%), most of which were in plant roots (40%) and bounded to lava (58%). The presence of LAS significantly increased the volatilization of phenanthrene and its metabolites, inhibited its mineralization and decreased the level of 14C-activity in lava. Moreover, LAS reduced the phenanthrene level in plant roots.

Corrosion protection with eco-friendly inhibitors

NASA Astrophysics Data System (ADS)

Shahid, Muhammad

2011-12-01

Corrosion occurs as a result of the interaction of a metal with its environment. The extent of corrosion depends on the type of metal, the existing conditions in the environment and the type of aggressive ions present in the medium. For example, CO3-2 and NO-3 produce an insoluble deposit on the surface of iron, resulting in the isolation of metal and consequent decrease of corrosion. On the other hand, halide ions are adsorbed selectively on the metal surface and prevent formation of the oxide phase on the metal surface, resulting in continuous corrosion. Iron, aluminum and their alloys are widely used, both domestically and industrially. Linear alkylbenzene and linear alkylbenzene sulfonate are commonly used as detergents. They have also been found together in waste water. It is claimed that these chemicals act as inhibitors for stainless steel and aluminum. Release of toxic gases as a result of corrosion in pipelines may lead in certain cases to air pollution and possible health hazards. Therefore, there are two ways to look at the relationship between corrosion and pollution: (i) corrosion of metals and alloys due to environmental pollution and (ii) environmental pollution as a result of corrosion protection. This paper encompasses the two scenarios and possible remedies for various cases, using 'green' inhibitors obtained either from plant extracts or from pharmaceutical compounds. In the present study, the effect of piperacillin sodium as a corrosion inhibitor for mild steel was investigated using a weight-loss method as well as a three-electrode dc electrochemical technique. It was found that the corrosion rate decreased as the concentration of the inhibitor increased up to 9×10-4 M 93% efficiency was exhibited at this concentration.

Molecular Dynamics Studies of Overbased Detergents on a Water Surface.

PubMed

Bodnarchuk, M S; Dini, D; Heyes, D M; Breakspear, A; Chahine, S

2017-07-25

Molecular dynamics (MD) simulations are reported of model overbased detergent nanoparticles on a model water surface which mimic their behavior on a Langmuir trough or large water droplet in engine oil. The simulations predict that the structure of the nanoparticle on a water surface is different to when it is immersed in a bulk hydrophobic solvent. The surfactant tails are partly directed out of the water, while the carbonate core maximizes its extent of contact with the water. Umbrella sampling calculations of the potential of mean force between two particles showed that they are associated with varying degrees with a maximum binding free energy of ca. 10 k B T for the salicylate stabilized particle, ca. 8 k B T for a sulfurized alkyl phenate stabilized particle, and ca. 5 k B T for a sulfonate stabilized particle. The differences in the strength of attraction depend on the proximity of nearest approach and the energy penalty associated with the disruption of the hydration shell of water molecules around the calcium carbonate core when the two particles approach. This is greatest for the sulfonate particle, which partially loses the surfactant ions to the solution, and least for the salicylate, which forms the weakest water "cage". The particles are separated by a water hydration layer, even at the point of closest approach.

Rational design of aromatic surfactants for graphene/natural rubber latex nanocomposites with enhanced electrical conductivity.

PubMed

Mohamed, Azmi; Ardyani, Tretya; Abu Bakar, Suriani; Sagisaka, Masanobu; Umetsu, Yasushi; Hamon, J J; Rahim, Bazura Abdul; Esa, Siti Rahmah; Abdul Khalil, H P S; Mamat, Mohamad Hafiz; King, Stephen; Eastoe, Julian

2018-04-15

Graphene nanoplatelets (GNPs) can be dispersed in natural rubber matrices using surfactants. The stability and properties of these composites can be optimized by the choice of surfactants employed as stabilizers. Surfactants can be designed and synthesized to have enhanced compatibility with GNPs as compared to commercially available common surfactants. Including aromatic groups in the hydrophobic chain termini improves graphene compatibility of surfactants, which is expected to increase with the number of aromatic moieties per surfactant molecule. Hence, it is of interest to study the relationship between molecular structure, dispersion stability and electrical conductivity enhancement for single-, double-, and triple-chain anionic graphene-compatible surfactants. Graphene-philic surfactants, bearing two and three chains phenylated at their chain termini, were synthesized and characterized by proton nuclear magnetic resonance ( 1 H NMR) spectroscopy. These were used to formulate and stabilize dispersion of GNPs in natural rubber latex matrices, and the properties of systems comprising the new phenyl-surfactants were compared with commercially available surfactants, sodium dodecylsulfate (SDS) and sodium dodecylbenzenesulfonate (SDBS). Raman spectroscopy, field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), and high-resolution transmission electron microscopy (HRTEM) were used to study structural properties of the materials. Electrical conductivity measurements and Zeta potential measurements were used to assess the relationships between surfactant architecture and nanocomposite properties. Small-angle neutron scattering (SANS) was used to study self-assembly structure of surfactants. Of these different surfactants, the tri-chain aromatic surfactant TC3Ph3 (sodium 1,5-dioxo-1,5-bis(3-phenylpropoxy)-3-((3phenylpropoxy)carbonyl) pentane-2-sulfonate) was shown to be highly graphene-compatible (nanocomposite electrical conductivity = 2.22 × 10 -5  S cm -1 ), demonstrating enhanced electrical conductivity over nine orders of magnitude higher than neat natural rubber-latex matrix (1.51 × 10 -14  S cm -1 ). Varying the number of aromatic moieties in the surfactants appears to cause significant differences to the final properties of the nanocomposites. Copyright © 2018 Elsevier Inc. All rights reserved.

Role of surfactant on thermoelectric behaviors of organic-inorganic composites

NASA Astrophysics Data System (ADS)

Shin, Sunmi; Roh, Jong Wook; Kim, Hyun-Sik; Chen, Renkun

2018-05-01

Hybrid organic/inorganic composites have recently attracted intensive interests as a promising candidate for flexible thermoelectric (TE) devices using inherently soft polymers as well as for increasing the degree of freedom to control TE properties. Experimentally, however, enhanced TE performance in hybrid composites has not been commonly observed, primarily due to inhomogeneous mixing between the inorganic and organic components which leads to limited electrical conduction in the less conductive component and consequently a low power factor in the composites compared to their single-component counterparts. In this study, we investigated the effects of different surfactants on the uniformity of mixing and the TE behaviors of the hybrid composites consisting of Bi0.5Sb1.5Te3 (BST) and poly(3,4-ethylenedioxythiophene) polystyrene sulfonate (PEDOT:PSS). We found that compared to dimethyl sulfoxide, which is the most widely used surfactant, Triton X-100 (TX-100) can lead to homogenous dispersion of BST in PEDOT:PSS. By systematically studying the effects of the surfactant concentration, we can attribute the better mixing capability of TX-100 to its non-ionic property, which results in homogenous mixing with a lower critical micelle concentration. Consequently, we observed simultaneous increase in electrical conductivity and Seebeck coefficient in the BST/PEDOT:PSS composites with the TX-100 surfactant.

Cytotoxicity Effects of Different Surfactant Molecules Conjugated to Carbon Nanotubes on Human Astrocytoma Cells

NASA Astrophysics Data System (ADS)

Dong, Lifeng; Witkowski, Colette M.; Craig, Michael M.; Greenwade, Molly M.; Joseph, Katherine L.

2009-12-01

Phase contrast and epifluorescence microscopy were utilized to monitor morphological changes in human astrocytoma cells during a time-course exposure to single-walled carbon nanotube (SWCNT) conjugates with different surfactants and to investigate sub-cellular distribution of the nanotube conjugates, respectively. Experimental results demonstrate that cytotoxicity of the nanotube/surfactant conjugates is related to the toxicity of surfactant molecules attached on the nanotube surfaces. Both sodium dodecyl sulfate (SDS) and sodium dodecylbenzene sulfonate (SDBS) are toxic to cells. Exposure to CNT/SDS conjugates (0.5 mg/mL) for less than 5 min caused changes in cell morphology resulting in a distinctly spherical shape compared to untreated cells. In contrast, sodium cholate (SC) and CNT/SC did not affect cell morphology, proliferation, or growth. These data indicate that SC is an environmentally friendly surfactant for the purification and dispersion of SWCNTs. Epifluorescence microscopy analysis of CNT/DNA conjugates revealed distribution in the cytoplasm of cells and did not show adverse effects on cell morphology, proliferation, or viability during a 72-h incubation. These observations suggest that the SWCNTs could be used as non-viral vectors for diagnostic and therapeutic molecules across the blood-brain barrier to the brain and the central nervous system.

Study on the sorption behaviour of estrone on marine sediments.

PubMed

Zhang, Jing; Yang, Gui-Peng; Li, Quan; Cao, Xiaoyan; Liu, Guangxing

2013-11-15

The sorption behaviour of estrone (E1) on marine sediments treated by different methods was systematically investigated. About 22 h was required for sorption equilibrium of E1. Sorption isotherms of E1 were well fitted with Freundlich model. The sorption behaviour of E1 on HCl-treatment and H2O-treatment sediments related significantly with the sediment organic carbon contents. Additionally, clay minerals and surface areas of sediments played dominant roles in the sorption of E1 on H2O2-treatment sediments. Some external factors which could affect sorption behaviour of E1 were also investigated. Our results showed that the sorption capacity of E1 on the sediments increased with the increasing concentrations of cationic surfactant cetyltrimethylammonium bromide (CTAB), nonionic surfactant polyoxyethylene (80) sorbitan esters (Tween 80) and salinity of seawater. In contrast, the sorption capacity of E1 decreased with the increasing concentration of anionic surfactant sodium dodecylbenzene sulfonate (SDBS), pH value and temperature of seawater. Copyright © 2013 Elsevier Ltd. All rights reserved.

Formulation Effects and the Off-target Transport of Pyrethroid Insecticides from Urban Hard Surfaces

PubMed Central

Jorgenson, Brant C.; Young, Thomas M.

2010-01-01

Controlled rainfall experiments utilizing drop forming rainfall simulators were conducted to study various factors contributing to off-target transport of off-the-shelf formulated pyrethroid insecticides from concrete surfaces. Factors evaluated included active ingredient, product formulation, time between application and rainfall (set time), and rainfall intensity. As much as 60% and as little as 0.8% of pyrethroid applied could be recovered in surface runoff depending primarily on product formulation, and to a lesser extent on product set time. Resulting wash-off profiles during one-hour storm simulations could be categorized based on formulation, with formulations utilizing emulsifying surfactants rather than organic solvents resulting in unique wash-off profiles with overall higher wash-off efficiency. These higher wash-off efficiency profiles were qualitatively replicated by applying formulation-free neat pyrethroid in the presence of independently applied linear alkyl benzene sulfonate (LAS) surfactant, suggesting that the surfactant component of some formulated products may be influential in pyrethroid wash-off from urban hard surfaces. PMID:20524665

Water Dynamics in Gyroid Phases of Self-Assembled Gemini Surfactants

DOE PAGES

Roy, Santanu; Skoff, David; Perroni, Dominic V.; ...

2016-02-14

Water-mediated ion transport through functional nanoporous materials depends on the dynamics of water confined within a given nanostructured morphology. In this study, we investigate hydrogen-bonding dynamics of interfacial water within a ‘normal’ (Type I) lyotropic gyroid phase formed by a gemini dicarboxylate surfactant self-assembly using a combina- tion of 2DIR spectroscopy and molecular dynamics simulations. Experiments and simulations demonstrate that water dynamics in the normal gyroid phase is one order of magnitude slower than that in bulk water, due to specific interactions between water, the ionic surfactant headgroups, and counterions. However, the dynamics of water in the normal gyroid phasemore » are faster than those of water confined in a reverse spherical micelle of a sulfonate surfactant, given that the water pool in the reverse micelle and the water pore in the gyroid phase have roughly the same diameters. This difference in confined water dynamics likely arises from the significantly reduced curvature- induced frustration at the convex interfaces of the normal gyroid, as compared to the concave interfaces of a reverse spherical micelle. These detailed insights into confined water dynamics may guide the future design of artificial membranes that rapidly transport protons and other ions.« less

Liquid phase exfoliated graphene for electronic applications

NASA Astrophysics Data System (ADS)

Sukumaran, Sheena S.; Jinesh, K. B.; Gopchandran, K. G.

2017-09-01

Graphene dispersions were prepared using the liquid phase exfoliation method with three different surfactants. One surfactant was used from each of the surfactant types, anionic, cationic, and non-ionic; those used, were sodium dodecylbenzene sulfonate (SDBS), cetyltrimethylammonium bromide (CTAB) and polyvinylpyrrolidone (PVP), respectively. Raman spectroscopy was used to investigate the number of layers and the nature of any defects present in the exfoliated graphene. The yield of graphene was found to be less with the non-ionic surfactant, PVP. The deconvolution of 2D peaks at ~2700 cm-1 indicated that graphene prepared using these surfactants resulted in sheets consisting of few-layer graphene. The ratio of intensity of the D and G bands in the Raman spectra showed that edge defect density is high for samples prepared with SDBS compared to the other two, and is attributed to the smaller size of the graphene sheets, as shown in the electron micrographs. In the case of the dispersion in PVP, it is found that the sizes of the graphene sheets are highly sensitive to the concentration of the surfactant used. Here, we have made an attempt to investigate the local density of states in the graphene sheets by measuring the tunnelling current-voltage characteristics. Graphene layers have shown consistent p-type behaviour when exfoliated with SDBS and n-type behaviour when exfoliated with CTAB, with a larger band gap for graphene exfoliated using CTAB. Hence, in addition to the known advantages of liquid phase exfoliation, we found that by selecting suitable surfactants, to a certain extent it is possible to tune the band gap and determine the type of majority carriers.

Geochemical significance of alkylbenzene distributions in flash pyrolysates of kerogens, coals, and asphaltenes

NASA Astrophysics Data System (ADS)

Hartgers, Walter A.; Damsté, Jaap S. Sinninghe; de Leeuw, Jan W.

1994-04-01

The distribution of C 0-C 5 alkylbenzenes in flash pyrolysates of forty-seven immature kerogens and coals from different geographical locations and of different ages were studied using gas chromatography (GC) in combination with mass spectrometry (MS) in order to decipher the origin of aromatic moieties in macromolecular matter. All possible structural isomers of the alkylated benzenes were determined, and, in some cases, absolute yields were calculated. Sulphur-rich (Type II-S) kerogens yield higher absolute amounts of alkylbenzenes in comparison to Type I, II, and III kerogens. The variations in internal distribution patterns of C 2-C 4 alkylbenzenes were analyzed using multivariate analysis techniques (principal component analysis; PCA). Major variations in alkylbenzene distributions were due to an increased abundance of specific alkylbenzenes, which are related to specific precursor moieties in the macromolecular structure assuming that they are mainly formed via β-cleavage. Alkylbenzenes possessing "linear" carbon skeletons are enhanced in flash pyrolysates of Guttenberg and Estonian Kukersite kerogens (Type I) and are proposed to be derived from linear precursors which have undergone cyclization/aromatization. Relatively high amounts of 1,2,3,4- and 1,2,3,5-tetramethylbenzenes were found in flash pyrolysates of Womble and Duvernay kerogens (Type II) which are likely to be derived from macromolecularly bound diaromatic carotenoids. The relatively high abundance of 1,2,3-trimethylbenzene and 1,3-/1,4-dimethylbenzene in pyrolysates of Monterey kerogens (Type II-S) is proposed to be indicative of the presence of bound nonaromatic carotenoids (e.g., β,β-carotene) which have undergone aromatization and/or loss of methyl groups upon diagenesis. 1-methyl-4-isopropylbenzene, which appears in relatively high amounts in flash pyrolysates of Walcott Chuar kerogen (Type II) and Catalan coals (Type III), is thought to be derived from a heteroatom-bound precursor. These results demonstrate that the structure of monoaromatic moieties in kerogen is biologically controlled. The internal distribution patterns of alkylbenzenes of flash pyrolysates of kerogens and asphaltenes show a marked resemblance, the latter showing a slight enhancement of alkylbenzenes with longer carbon skeletons. These observations support the idea that asphaltenes are structurally related to kerogen and that aromatic moieties in asphaltenes are bound by fewer intermolecular bridges.

A new desorption method for removing organic solvents from activated carbon using surfactant.

PubMed

Hinoue, Mitsuo; Ishimatsu, Sumiyo; Fueta, Yukiko; Hori, Hajime

2017-03-28

A new desorption method was investigated, which does not require toxic organic solvents. Efficient desorption of organic solvents from activated carbon was achieved with an ananionic surfactant solution, focusing on its washing and emulsion action. Isopropyl alcohol (IPA) and methyl ethyl ketone (MEK) were used as test solvents. Lauryl benzene sulfonic acid sodium salt (LAS) and sodium dodecyl sulfate (SDS) were used as the surfactant. Activated carbon (100 mg) was placed in a vial and a predetermined amount of organic solvent was added. After leaving for about 24 h, a predetermined amount of the surfactant solution was added. After leaving for another 72 h, the vial was heated in an incubator at 60°C for a predetermined time. The organic vapor concentration was then determined with a frame ionization detector (FID)-gas chromatograph and the desorption efficiency was calculated. A high desorption efficiency was obtained with a 10% surfactant solution (LAS 8%, SDS 2%), 5 ml desorption solution, 60°C desorption temperature, and desorption time of over 24 h, and the desorption efficiency was 72% for IPA and 9% for MEK. Under identical conditions, the desorption efficiencies for another five organic solvents were investigated, which were 36%, 3%, 32%, 2%, and 3% for acetone, ethyl acetate, dichloromethane, toluene, and m-xylene, respectively. A combination of two anionic surfactants exhibited a relatively high desorption efficiency for IPA. For toluene, the desorption efficiency was low due to poor detergency and emulsification power.

A new desorption method for removing organic solvents from activated carbon using surfactant

PubMed Central

Hinoue, Mitsuo; Ishimatsu, Sumiyo; Fueta, Yukiko; Hori, Hajime

2017-01-01

Objectives: A new desorption method was investigated, which does not require toxic organic solvents. Efficient desorption of organic solvents from activated carbon was achieved with an ananionic surfactant solution, focusing on its washing and emulsion action. Methods: Isopropyl alcohol (IPA) and methyl ethyl ketone (MEK) were used as test solvents. Lauryl benzene sulfonic acid sodium salt (LAS) and sodium dodecyl sulfate (SDS) were used as the surfactant. Activated carbon (100 mg) was placed in a vial and a predetermined amount of organic solvent was added. After leaving for about 24 h, a predetermined amount of the surfactant solution was added. After leaving for another 72 h, the vial was heated in an incubator at 60°C for a predetermined time. The organic vapor concentration was then determined with a frame ionization detector (FID)-gas chromatograph and the desorption efficiency was calculated. Results: A high desorption efficiency was obtained with a 10% surfactant solution (LAS 8%, SDS 2%), 5 ml desorption solution, 60°C desorption temperature, and desorption time of over 24 h, and the desorption efficiency was 72% for IPA and 9% for MEK. Under identical conditions, the desorption efficiencies for another five organic solvents were investigated, which were 36%, 3%, 32%, 2%, and 3% for acetone, ethyl acetate, dichloromethane, toluene, and m-xylene, respectively. Conclusions: A combination of two anionic surfactants exhibited a relatively high desorption efficiency for IPA. For toluene, the desorption efficiency was low due to poor detergency and emulsification power. PMID:28132972

Ionic liquids for low-tension oil recovery processes: Phase behavior tests.

PubMed

Rodriguez-Escontrela, Iria; Puerto, Maura C; Miller, Clarence A; Soto, Ana

2017-10-15

Chemical flooding with surfactants for reducing oil-brine interfacial tensions (IFTs) to mobilize residual oil trapped by capillary forces has a great potential for Enhanced Oil Recovery (EOR). Surface-active ionic liquids (SAILs) constitute a class of surfactants that has recently been proposed for this application. For the first time, SAILs or their blends with an anionic surfactant are studied by determining equilibrium phase behavior for systems of about unit water-oil ratio at various temperatures. The test fluids were model alkane and aromatic oils, NaCl brine, and synthetic hard seawater (SW). Patterns of microemulsions observed are those of classical phase behavior (Winsor I-III-II transition) known to correlate with low IFTs. The two anionic room-temperature SAILs tested were made from common anionic surfactants by substituting imidazolium or phosphonium cations for sodium. These two anionic and two cationic SAILs were found to have little potential for EOR when tested individually. Thus, also tested were blends of an anionic internal olefin sulfonate (IOS) surfactant with one of the anionic SAILs and both cationic SAILs. Most promising for EOR was the anionic/cationic surfactant blend of IOS with [C 12 mim]Br in SW. A low equilibrium IFT of ∼2·10 -3 mN/m was measured between n-octane and an aqueous solution having the optimal blend ratio for this system at 25°C. Copyright © 2017 Elsevier Inc. All rights reserved.

Influence of surfactants on the microstructure and electrochemical performance of the tin oxide anode in lithium ion batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Yan-Hui, E-mail: sunyanhui0102@163.com; Guangzhou Key Laboratory of Materials for Energy Conversion and Storage, South China Normal University, Guangzhou 510006; Dong, Pei-Pei

2016-02-15

Highlights: • CTAB and SDS alter the formation of SnO{sub 2} from nanosheets to nanocubes during oxalate precipitation. • The CTAB concentration affects the SnO{sub 2} crystal growth direction, morphology and size. • The SnO{sub 2} anode synthesized using CTAB exhibited superior electrochemical performance. • Proposed a mechanism of influence of surfactant on SnO{sub 2} in the precipitation and annealing process. - Abstract: Different SnO{sub 2} micro–nano structures are prepared by precipitation using a surfactant-assisted process. The surfactants, such as cetyltriethylammonium bromide (CTAB) or sodium dodecyl benzene sulfonate (SDBS), can change the crystal growth direction and microstructure of SnO{sub 2}more » primary and secondary particles. Larger SnO{sub 2} nanosheets were synthesized without surfactant, and micro-fragments composed of small nanospheres or nanocubes were synthesized using CTAB and SDBS. The CTAB-assisted process resulted in smaller primary particles and larger specific surface area and larger pore volume, as a lithium-ion-battery anode that exhibits superior electrochemical performance compared to the other two anodes. Further investigation showed that the concentration of CTAB had a substantial influence on the growth of the crystal face, morphology and size of the SnO{sub 2} secondary particles, which influenced the electrochemical performance of the anode. A simple mechanism for the influence of surfactants on SnO{sub 2} morphology and size in the precipitation and annealing process is proposed.« less

Method for removing elemental sulfur in sour gas wells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sample, T.E. Jr.

1975-09-30

A process is described for removing sulfur deposits from sour gas wells. The formation, well, and surface equipment are contacted with a chemical composition whose aqueous solution will solubilize the sulfur by primary chemical reaction and contains a wetting agent to facilitate and accelerate the sulfur dissolution and removal. The wetting agent or surfactant may be any of a wide variety of surface-active substances such as soaps, sodium or ammonium salts of alkyl or alkyl-aryl sulfates and sulfonates. Nonionic surfactants are preferred, such as ethoxylated substituted phenols. The aqueous solvents are capable of chemically reacting with sulfur to form water-solublemore » sulfur derivatives and include aqueous solutions of alkalies, bases (both inorganic and organic), ammonia, sulfites, bisulfites, etc. (6 claims)« less

New rapid methods for determination of total LAS in sewage sludge by high performance liquid chromatography (HPLC) and capillary electrophoresis (CE).

PubMed

Villar, M; Callejón, M; Jiménez, J C; Alonso, E; Guiraúm, A

2009-02-23

Linear alkylbenzene sulfonates (LAS) are the most common synthetic anionic surfactant used in domestic and industrial detergents, with a global production of 2.4x10(6) t year(-1). After use and disposal, LAS may enter the environment by one of the several routes, including by direct discharge to surface water or discharge to water from sewage treatment plants. Sewage treatment plants break down LAS only partly: some of them remain in effluent and other fraction is adsorbed in sewage solid. New and rapid methods for determination of total LAS from sewage sludge based on microwave assisted extraction and HPLC-FL and CE-DAD determination are proposed. The extraction of total LAS is carried out by using microwaves energy, an extraction time of 10 min and 5 mL of methanol. For HPLC-FL determination, mobile phase acetonitrile-water was used, comprising 60% (v/v) from 0 to 1 min and a flow rate of 1 mL min(-1) programmed to 100% acetonitrile between 1 and 2 min and a flow rate of 2 mL min(-1). The final composition was maintained for a further 5 min. The determination of total LAS by CE-DAD was performed in a phosphate buffer (10 mM, pH 9). The separation voltage was 25 kV and the temperature of the capillary was 30 degrees C. Injections were performed in the pressure mode and the injection time was set at 12 s. The determination of total LAS is carried out in less than 5 min. The methods did not require clean-up or preconcentration steps. Detection limit for total LAS in the sludge was 3.03 mg kg(-1) using HPLC-FL and 21.0 mg kg(-1) using CE-DAD, and recoveries were >85% using both determination methods. Concentrations of total LAS obtained using both methods were compared with the sum of concentrations of homologues LAS C-10, LAS C-11, LAS C-12 and LAS C-13 obtained using microwaves assisted extraction and HPLC-FL and CE-DAD determination.

Interaction between amphiphilic ionic liquid 1-butyl-3-methylimidazolium octyl sulfate and anionic polymer of sodium polystyrene sulfonate in aqueous medium

NASA Astrophysics Data System (ADS)

Barhoumi, Z.; Saini, M.; Amdouni, N.; Pal, A.

2016-09-01

The micellization of an aqueous solution of the surface active ionic liquid (SAIL), 1-butyl-3-methylimidazolium octylsufate (C4mim)(C8OSO3) and its interaction with an anionic polymer sodium polystyrene sulfonate, (NaPSS) were studied using conductimetry, tensiometry and fluorimetry. Surface tension profile shows a more dramatic increase in the value of surface tension of aqueous (C4mim)(C8OSO3) before the critical micelle concentration (cmc) of IL. The critical micelle concentration (cmc) value of this surfactant was found out from conductance measurements. The thermodynamic parameters, i.e., Gibb's free energy, enthalpy, and entropy of micellization of the IL in aqueous solution have been calculated. Behavior of fluorescence probe confirms the binding interactions between SAIL and the polyelectrolyte.

Effect of surfactants and manufacturing methods on the electrical and thermal conductivity of carbon nanotube/silicone composites.

PubMed

Vilčáková, Jarmila; Moučka, Robert; Svoboda, Petr; Ilčíková, Markéta; Kazantseva, Natalia; Hřibová, Martina; Mičušík, Matej; Omastová, Mária

2012-11-05

The effect of ionic surfactants and manufacturing methods on the separation and distribution of multi-wall carbon nanotubes (CNTs) in a silicone matrix are investigated. The CNTs are dispersed in an aqueous solution of the anionic surfactant dodecylbenzene sulfonic acid (DBSA), the cationic surfactant cetyltrimethylammonium bromide (CTAB), and in a DBSA/CTAB surfactant mixture. Four types of CNT-based composites of various concentrations from 0 to 6 vol.% are prepared by simple mechanical mixing and sonication. The morphology, electrical and thermal conductivity of the CNT-based composites are analyzed. The incorporation of both neat and modified CNTs leads to an increase in electrical and thermal conductivity. The dependence of DC conductivity versus CNT concentration shows percolation behaviour with a percolation threshold of about 2 vol.% in composites with neat CNT. The modification of CNTs by DBSA increases the percolation threshold to 4 vol.% due to the isolation/separation of individual CNTs. This, in turn, results in a significant decrease in the complex permittivity of CNT–DBSA-based composites. In contrast to the percolation behaviour of DC conductivity, the concentration dependence of thermal conductivity exhibits a linear dependence, the thermal conductivity of composites with modified CNTs being lower than that of composites with neat CNTs. All these results provide evidence that the modification of CNTs by DBSA followed by sonication allows one to produce composites with high homogeneity.

Identification of persisten anionic surfactant-derived chemicals in sewage effluent and groundwater

USGS Publications Warehouse

Field, J.A.; Leenheer, J.A.; Thorn, K.A.; Barber, L.B.; Rostad, C.; Macalady, D.L.; Daniel, S.R.

1992-01-01

Preparative isolation and fractionation procedures coupled with spectrometric analyses were used to identify surfactant-derived contaminants in sewage effluent and sewage-contaminated groundwater from a site located on Cape Cod, Massachusetts. Anionic surfactants and their biodegradation intermediates were isolated from field samples by ion exchange and fractionated by solvent extraction and adsorption chromatography. Fractions were analyzed by 13C nuclear magnetic resonance spectrometry and gas chromatography-mass spectrometry. Carboxylated residues of alkylphenol polyethoxylate surfactants were detected in sewage effluent and contaminated groundwater. Linear alkylbenzenesulfonates (LAS) were identified in sewage effluent and groundwater. Groundwater LAS composition suggested preferential removal of select isomers and homologs due to processes of biodegradation and partitioning. Tetralin and indane sulfonates (DATS), alicyclic analogs of LAS, were also identified in field samples. Although DATS are a minor portion of LAS formulations, equivalent concentrations of LAS and DATS in groundwater suggested persistence of alicyclic contaminant structures over those of linear structure. Sulfophenyl-carboxylated (SPC) LAS biodegradation intermediates were determined in sewage effluent and groundwater. Homolog distributions suggested that SPC containing 3-10 alkyl-chain carbons persist during infiltration and groundwater transport. Surfactant-derived residues detected in well F300-50 groundwater have a minimum residence time in the range of 2.7-4.6 yr. LAS detected in groundwater at 500 m from infiltration has been stable over an estimated 50-500 half lives.

Identification of persistent anionic surfactant-derived chemicals in sewage effluent and groundwater

USGS Publications Warehouse

Field, Jennifer A.; Leenheer, Jerry A.; Thorn, Kevin A.; Barber, Larry B.; Rostad, Colleen; Macalady, Donald L.; Daniel, Stephen R.

1992-01-01

Preparative isolation and fractionation procedures coupled with spectrometric analyses were used to identify surfactant-derived contaminants in sewage effluent and sewage-contaminated groundwater from a site located on Cape Cod, Massachusetts. Anionic surfactants and their biodegradation intermediates were isolated from field samples by ion exchange and fractionated by solvent extraction and adsorption chromatography. Fractions were analyzed by 13C nuclear magnetic resonance spectrometry and gas chromatography-mass spectrometry. Carboxylated residues of alkylphenol polyethoxylate surfactants were detected in sewage effluent and contaminated groundwater. Linear alkylbenzenesulfonates (LAS) were identified in sewage effluent and groundwater. Groundwater LAS composition suggested preferential removal of select isomers and homologs due to processes of biodegradation and partitioning. Tetralin and indane sulfonates (DATS), alicyclic analogs of LAS, were also identified in field samples. Although DATS are a minor portion of LAS formulations, equivalent concentrations of LAS and DATS in groundwater suggested persistence of alicyclic contaminant structures over those of linear structure. Sulfophenyl-carboxylated (SPC) LAS biodegradation intermediates were determined in sewage effluent and groundwater. Homolog distributions suggested that SPC containing 3–10 alkyl-chain carbons persist during infiltration and groundwater transport. Surfactant-derived residues detected in well F300-50 groundwater have a minimum residence time in the range of 2.7–4.6 yr. LAS detected in groundwater at 500 m from infiltration has been stable over an estimated 50–500 half lives.

Transport of fluorescently labeled hydroxyapatite nanoparticles in saturated granular media at environmentally relevant concentrations of surfactants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Dengjun; Su, Chuming; Liu, Chongxuan

Hydroxyapatite nanoparticle (nHAP) is being used to remediate soils and aquifers contaminated with metals and radionuclides; however, the mobility of nHAP is still poorly understood in subsurface granular environments. In this study, transport and retention kinetics of alizarin red S (ARS)-labeled nHAP were investigated in water-saturated quartz sand at low concentrations of surfactants: sodium dodecyl benzene sulfonate (SDBS, an anionic surfactant, 0–50 mg L–1) and cetyltrimethylammonium bromide (CTAB, a cationic surfactant, 0–5 mg L–1). Both surfactants were found to have a marked effect on the electrokinetic properties of ARS-nHAP and, consequently, on their transport and retention behaviors. Transport of nanoparticlesmore » (NPs) increased significantly with increasing SDBS concentration, largely because of enhanced colloidal stability and reduced aggregate size arising from enhanced electrostatic, osmotic, and elastic-steric repulsions between ARS-nHAP and sand grains. Conversely, transport decreased significantly in the presence of increasing CTAB concentrations due to reduced surface charge and consequential enhanced aggregation of the NPs. Osmotic and elastic-steric repulsions played only a minor role in enhancing the colloidal stability of ARS-nHAP in the presence of CTAB. Retention profiles of ARS-nHAP exhibited hyperexponential-shapes (decreasing rates of retention with increasing distance) for all conditions tested, and became more pronounced as CTAB concentration increased. The phenomenon was attributed to the aggregation and ripening of ARS-nHAP in the presence of surfactants, particularly CTAB. Overall, the present study suggests that surfactants at environmentally relevant concentrations may be an important consideration in employing nHAP for engineered in-situ remediation of certain metals and radionuclides in contaminated soils and aquifers.« less

Responses and toxin bioaccumulation in duckweed (Lemna minor) under microcystin-LR, linear alkybenzene sulfonate and their joint stress.

PubMed

Wang, Zhi; Xiao, Bangding; Song, Lirong; Wang, Chunbo; Zhang, Junqian

2012-08-30

Microcystin-LR (MCLR) and linear alkylbenzene sulfonate (LAS) are commonly found in eutrophic lakes due to toxic cyanobacterial blooms and exogenous organic compounds pollution. However, the ecotoxicological risk of their combination in the aquatic environment is unknown. This study investigated the effects of MCLR, LAS and their mixture on duckweed (Lemna minor) growth and physiological responses. MCLR accumulation in duckweed, with or without LAS, was also examined. Growth of duckweed and chlorophyll-a contents were significantly reduced after 8d exposure to high concentrations of MCLR (≥ 3 μg/ml), LAS (≥ 20 μg/ml) and their mixture (≥ 3+10 μg/ml). After 2d of exposure, superoxide dismutase activity and glutathione content in duckweed increased with increasing concentrations of MCLR, LAS and their mixture, with a significant difference observable after 8d of exposure. When MCLR and LAS concentrations were lower (≤ 0.1+1 μg/ml), the interaction of them is synergistic, but when the concentrations were higher, the synergy was weak. MC accumulation was much higher at 2d than at 8d when duckweed was exposed to lower concentrations of MCLR (≤ 3 μg/ml) or MCLR-LAS (≤ 3+10 μg/ml). Furthermore, LAS significantly enhanced the accumulation of MCLR in duckweed, even with LAS concentrations as low as 0.3 μg/ml (environmental concentration), indicating that greater negative ecological risks and higher MCLR phytoremediation potentials of duckweed might occur in MCLR-LAS-concomitant water. Copyright © 2012 Elsevier B.V. All rights reserved.

Investigation on the interaction of catalase with sodium lauryl sulfonate and the underlying mechanisms.

PubMed

Wang, Jing; Jia, Rui; Wang, Jiaxi; Sun, Zhiqiang; Wu, Zitao; Liu, Rutao; Zong, Wansong

2018-02-01

As a classic type of anionic surfactants, sodium lauryl sulfonate (SLS) might change the structure and function of antioxidant enzyme catalase (CAT) through their direct interactions. However, the underlying molecular mechanism is still unknown. This study investigated the direct interaction of SLS with CAT molecule and the underlying mechanisms using multi-spectroscopic methods, isothermal titration calorimetry, and molecular docking studies. No obvious effects were observed on CAT structure and activity under low SLS concentration exposure. The particle size of CAT molecule decreased and CAT activity was slightly inhibited under high SLS concentration exposure. SLS prefers to bind to the interface of CAT mainly via van der Waals' forces and hydrogen bonds. Subsequently, SLS interacts with the amino acid residues around the heme groups of CAT via hydrophobic interactions and might inhibit CAT activity. © 2017 Wiley Periodicals, Inc.

Enhanced Aqueous Solubility of Long Wavelength Voltage-Sensitive Dyes by Covalent Attachment of Polyethylene Glycol

PubMed Central

Patrick, Michael J.; Ernst, Lauren A.; Waggoner, Alan S.; Thai, Dung; Salama, Guy

2011-01-01

Long wavelength voltage-sensitive dyes (VSDs) called Pittsburgh (PGH) dyes were recently synthesized by coupling various heterocyclic groups to a styryl-thiophene intermediate forming extended, partially rigidized chromophores. Unlike most styryl VSDs, dyes with a sulfonic acid anchor directly attached to the chromophore showed no solvatochromic absorption shifts. The limited water solubility of many long wavelength VSDs requires the use of surfactants to transport the dye through aqueous media and effectively label biological membranes. Here, we tested the chemical substitution of the sulfonic acid moiety with polyethyleneglycol (PEG) chains ranging from MW 750 to 5000, to overcome the poor solubility of VSDs while retaining their properties as VSDs. The chemical synthesis of PGH dyes and their PEG derivatives are described. The PEG-derivatives were soluble in aqueous solutions (> 1 mM) and still reported membrane potential changes. In frog and mouse hearts, the voltage sensitivity (ΔF/F per action potential) and spectral properties of PEG dyes were the same as the sulfonated analogs. Thus, the solubility of VSDs can be considerably improved with small polyethyleneglycol chains and can provide an effective approach to improve staining of excitable tissues and optical recordings of membrane potential. PMID:17912389

Synergic effect of SDBS and GA to prepare stable dispersion of CNT in water for industrial heat transfer applications

NASA Astrophysics Data System (ADS)

Babita; Sharma, S. K.; Mital Gupta, Shipra

2018-05-01

Dispersion of hydrophobic carbon nanotubes in water is challenging. Herein, efforts have been made to study the dispersive effect of surface active agents on multi-walled carbon nanotubes (MWCNT). A method was developed to prepare a stable dispersion of MWCNT using sodium dodecyl benzene sulfonate (SDBS) and gum arabic (GA). Effect of ultrasonication time and surfactant concentration was also investigated. Compared to pure SDBS and GA based dispersion, their mixture was found to be effective to obtain a better dispersion of MWCNT, reflecting a synergistic effect of this mixture due to electrostatic and steric hindrance mechanism of surfactants. Rheology of CNT nanofluids showed the Newtonian behavior as viscosity was independent of shear rate. The viscosity of CNT nanofluids was higher than that of water. The thermal conductivity of dispersion was much higher than that of base fluid. This study provides the bases for using mixed surfactant system to disperse MWCNT in the polar base fluid to prepare nanofluids having enhanced thermal conductivity which can be used for heat transfer applications.

Contact Angle Measurements: an Alternative Approach Towards Understanding the Mechanism of Increased Drug Dissolution from Ethylcellulose Tablets Containing Surfactant and Exploring the Relationship Between Their Contact Angles and Dissolution Behaviors.

PubMed

Liu, Tiaotiao; Hao, Jingqiang; Yang, Baixue; Hu, Beibei; Cui, Zhixiang; Li, Sanming

2018-05-01

The addition of surfactant in tablet was a well-defined approach to improve drug dissolution rate. While the selected surfactant played a vital role in improving the wettability of tablet by medium, it was equally important to improve the dissolution rate by permeation effect due to production of pores or the reduced inter-particle adhesion. Furthermore, understanding the mechanism of dissolution rate increased was significant. In this work, contact angle measurement was taken up as an alternative approach for understanding the dissolution rate enhancement for tablet containing surfactant. Ethylcellulose, as a substrate, was used to prepare tablet. Four surfactants, sodium dodecyl sulfate (SDS), sodium dodecylbenzenesulfonate (SDBS), dodecyltrimethylammonium bromide (DTAB), and sodium lauryl sulfonate (SLS), were used. Berberine hydrochloride, metformin hydrochloride, and rutin were selected as model drugs. The contact angle of tablet in the absence and presence of surfactant was measured to explore the mechanism. The dissolution test was investigated to verify the mechanism and to establish a correlation with the contact angle. The result showed that the mechanism was the penetration effect rather than the wetting effect. The dissolution increased with a reduction in the contact angle. DTAB was found to obtain the highest level of dissolution enhancement and the lowest contact angle, while SDS, SDBS, and SLS were found to be the less effective in both dissolution enhancement and contact angle decrease. Therefore, contact angle was a good indicator for dissolution behavior besides exploring the mechanism of increased dissolution, which shows great potential in formula screening.

Cu sbnd Al sbnd Fe layered double hydroxides with CO32- and anionic surfactants with different alkyl chains in the interlayer

NASA Astrophysics Data System (ADS)

Trujillano, Raquel; Holgado, María Jesús; González, José Luis; Rives, Vicente

2005-08-01

Layered double hydroxides (LDHs), with the hydrotalcite-like structure containing Cu(II), Al(III) and Fe(III) in the layers, and different alkyl sulfonates in the interlayer, have been prepared and characterized by powder X-ray diffraction, FT-IR spectroscopy, differential thermal analysis and thermogravimetric analysis. Pure crystalline phases have been obtained in all cases. Upon heating, combustion of the organic chain takes place at lower temperature than the corresponding sodium salts.

Solar-mediated thermo-electrochemical oxidation of sodium dodecyl benzene sulfonate by modulating the effective oxidation potential and pathway for green remediation of wastewater.

PubMed

Gu, Di; Gao, Simeng; Jiang, TingTing; Wang, Baohui

2017-03-15

To match the relentless pursuit of three research hot points - efficient solar utilization, green and sustainable remediation of wastewater and advanced oxidation processes, solar-mediated thermo-electrochemical oxidation of surfactant was proposed and developed for green remediation of surfactant wastewater. The solar thermal electrochemical process (STEP), fully driven with solar energy to electric energy and heat and without an input of other energy, sustainably serves as efficient thermo-electrochemical oxidation of surfactant, exemplified by SDBS, in wastewater with the synergistic production of hydrogen. The electrooxidation-resistant surfactant is thermo-electrochemically oxidized to CO 2 while hydrogen gas is generated by lowing effective oxidation potential and suppressing the oxidation activation energy originated from the combination of thermochemical and electrochemical effect. A clear conclusion on the mechanism of SDBS degradation can be proposed and discussed based on the theoretical analysis of electrochemical potential by quantum chemical method and experimental analysis of the CV, TG, GC, FT-IR, UV-vis, Fluorescence spectra and TOC. The degradation data provide a pilot for the treatment of SDBS wastewater that appears to occur via desulfonation followed by aromatic-ring opening. The solar thermal utilization that can initiate the desulfonation and activation of SDBS becomes one key step in the degradation process.

Solar-mediated thermo-electrochemical oxidation of sodium dodecyl benzene sulfonate by modulating the effective oxidation potential and pathway for green remediation of wastewater

PubMed Central

Gu, Di; Gao, Simeng; Jiang, TingTing; Wang, Baohui

2017-01-01

To match the relentless pursuit of three research hot points - efficient solar utilization, green and sustainable remediation of wastewater and advanced oxidation processes, solar-mediated thermo-electrochemical oxidation of surfactant was proposed and developed for green remediation of surfactant wastewater. The solar thermal electrochemical process (STEP), fully driven with solar energy to electric energy and heat and without an input of other energy, sustainably serves as efficient thermo-electrochemical oxidation of surfactant, exemplified by SDBS, in wastewater with the synergistic production of hydrogen. The electrooxidation-resistant surfactant is thermo-electrochemically oxidized to CO2 while hydrogen gas is generated by lowing effective oxidation potential and suppressing the oxidation activation energy originated from the combination of thermochemical and electrochemical effect. A clear conclusion on the mechanism of SDBS degradation can be proposed and discussed based on the theoretical analysis of electrochemical potential by quantum chemical method and experimental analysis of the CV, TG, GC, FT-IR, UV-vis, Fluorescence spectra and TOC. The degradation data provide a pilot for the treatment of SDBS wastewater that appears to occur via desulfonation followed by aromatic-ring opening. The solar thermal utilization that can initiate the desulfonation and activation of SDBS becomes one key step in the degradation process. PMID:28294180

Solar-mediated thermo-electrochemical oxidation of sodium dodecyl benzene sulfonate by modulating the effective oxidation potential and pathway for green remediation of wastewater

NASA Astrophysics Data System (ADS)

Gu, Di; Gao, Simeng; Jiang, Tingting; Wang, Baohui

2017-03-01

To match the relentless pursuit of three research hot points - efficient solar utilization, green and sustainable remediation of wastewater and advanced oxidation processes, solar-mediated thermo-electrochemical oxidation of surfactant was proposed and developed for green remediation of surfactant wastewater. The solar thermal electrochemical process (STEP), fully driven with solar energy to electric energy and heat and without an input of other energy, sustainably serves as efficient thermo-electrochemical oxidation of surfactant, exemplified by SDBS, in wastewater with the synergistic production of hydrogen. The electrooxidation-resistant surfactant is thermo-electrochemically oxidized to CO2 while hydrogen gas is generated by lowing effective oxidation potential and suppressing the oxidation activation energy originated from the combination of thermochemical and electrochemical effect. A clear conclusion on the mechanism of SDBS degradation can be proposed and discussed based on the theoretical analysis of electrochemical potential by quantum chemical method and experimental analysis of the CV, TG, GC, FT-IR, UV-vis, Fluorescence spectra and TOC. The degradation data provide a pilot for the treatment of SDBS wastewater that appears to occur via desulfonation followed by aromatic-ring opening. The solar thermal utilization that can initiate the desulfonation and activation of SDBS becomes one key step in the degradation process.

Oligomers, organosulfates, and nitroxy organosulfates identified in rainwater

NASA Astrophysics Data System (ADS)

Altieri, K. E.; Turpin, B. J.; Seitzinger, S. P.

2008-12-01

Wet deposition is an important removal mechanism for atmospheric organic matter, and a potentially important input for receiving ecosystems, yet less than 50 percent of rainwater organic matter is considered chemically characterized. Precipitation samples collected in New Jersey, USA, were analyzed by negative ion ultra-high resolution electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS). We document the presence of 552 unique compounds in the rainwater over a mass range of 50-500 Da, in four compound classes (i.e., CHO, CHOS, CHON, and CHONS). The presence of oligomers, organosulfates, nitroxy organosulfates, organic acids, and linear alkylbenzene sulfonates is reported. Some compounds detected have distinct primary sources; however, the composition of the bulk of this material suggests it is formed in the atmosphere and composed of known contributors to secondary organic aerosol. For example, eight oligomer series known to form through aqueous photooxidation of methylglyoxal and organosulfate compounds known to form from 4 precursors in smog chamber experiments were identified in the rainwater samples. The oligomers, organosulfates, and nitroxy organosulfates detected in the rainwater could all contribute to the HULIS fraction of atmospheric organic matter.

Are additive effects of dietary surfactants on intestinal tight junction integrity an overlooked human health risk? - A mixture study on Caco-2 monolayers.

PubMed

Glynn, Anders; Igra, Annachiara Malin; Sand, Salomon; Ilbäck, Nils Gunnar; Hellenäs, Karl Erik; Rosén, Johan; Aspenström-Fagerlund, Bitte

2017-08-01

Surfactants may cause dysfunction of intestinal tight junctions (TJs), which is a common feature of intestinal autoimmune diseases. Effects of dietary surfactants on TJ integrity, measured as trans-epithelial resistance (TEER), were studied in Caco-2 cell monolayers. Cytotoxicity was assessed as apical LDH leakage. Monolayers were apically exposed for 60 min to the dietary surfactants solanine and chaconine (SC, potato glycoalkaloids, 0-0.25 mM), perfluorooctane sulfonic acid (PFOS, industrial contaminant, 0-0.8 mM), and sucrose monolaurate (SML, food emulsifier E 473, 0-2.0 mM) separately and as a mixture. Dose-response modelling of TEER EC 50 showed that SC were 2.7- and 12-fold more potent than PFOS and SML, respectively. The mixture was composed of 1 molar unit SC, 2.7 units PFOS and 12 units SML ("SC TEER equivalent" proportions 1:1:1). Mixture exposure (0-0.05 mM SC equivalents) dose-response modelling suggested additive action on TJ integrity. Increasing SC and SML concentrations caused increased LDH leakage, but PFOS decreased LDH leakage at intermediate exposure concentrations. In the mixture PFOS appeared to protect from extensive SC- and SML-induced LDH leakage. Complex mixtures of surfactants in food may act additively on intestinal TJ integrity, which should be considered in risk assessment of emulsifier authorisation for use in food production. Copyright © 2017 Elsevier Ltd. All rights reserved.

Activation of mouse and human peroxisome proliferator-activated receptor alpha by perfluoroalkyl acids of different functional groups and chain lengths.

PubMed

Wolf, Cynthia J; Takacs, Margy L; Schmid, Judith E; Lau, Christopher; Abbott, Barbara D

2008-11-01

Perfluoroalkyl acids (PFAAs) are surfactants used in consumer products and persist in the environment. Some PFAAs elicit adverse effects on rodent development and survival. PFAAs can activate peroxisome proliferator-activated receptor alpha (PPARalpha) and may act via PPARalpha to produce some of their effects. This study evaluated the ability of numerous PFAAs to induce mouse and human PPARalpha activity in a transiently transfected COS-1 cell assay. COS-1 cells were transfected with either a mouse or human PPARalpha receptor-luciferase reporter plasmid. After 24 h, cells were exposed to either negative controls (water or dimethyl sulfoxide, 0.1%); positive control (WY-14643, PPARalpha agonist); perfluorooctanoic acid or perfluorononanoic acid at 0.5-100 microM; perfluorobutanoic acid, perfluorohexanoic acid, perfluorohexane sulfonate, or perfluorodecanoic acid (PFDA) at 5-100 microM; or perfluorobutane sulfonate or perfluorooctane sulfonate at 1-250 microM. After 24 h of exposure, luciferase activity from the plasmid was measured. Each PFAA activated both mouse and human PPARalpha in a concentration-dependent fashion, except PFDA with human PPARalpha. Activation of PPARalpha by PFAA carboxylates was positively correlated with carbon chain length, up to C9. PPARalpha activity was higher in response to carboxylates compared to sulfonates. Activation of mouse PPARalpha was generally higher compared to that of human PPARalpha. We conclude that, in general, (1) PFAAs of increasing carbon backbone chain lengths induce increasing activity of the mouse and human PPARalpha with a few exceptions, (2) PFAA carboxylates are stronger activators of mouse and human PPARalpha than PFAA sulfonates, and (3) in most cases, the mouse PPARalpha appears to be more sensitive to PFAAs than the human PPARalpha in this model.

Impact of the 1993 flood on the distribution of organic contaminants in bed sediments of the Upper Mississippi River

USGS Publications Warehouse

Barber, L.B.; Writer, J.H.

1998-01-01

The 1500 km Upper Mississippi River (UMR) consists of 29 navigation pools and can be divided into the upper reach (pools 1-4), the middle reach (pools 5-13), and the lower reach (pools 14-26). Comparison of composite bed sediment samples collected from the downstream third of 24 pools before and after the 1993 UMR flood provides fieldscale data on the effect of the flood on sediment organic compound distributions. The sediments were analyzed for organic carbon, coprostanol, polynuclear aromatic hydrocarbons including pyrene, linear alkylbenzene-sulfonates, polychlorinated biphenyls (PCBs), and organochlorine pesticides. Most of the target compounds were detected in all of the sediment samples, although concentrations were generally <1 mg/kg. The highest concentrations typically occurred in the upper reach, an urbanized area on a relatively small river. Pool 4 (Lake Pepin) is an efficient sediment trap, and concentrations of the compounds below pool 4 were substantially lower than those in pools 2-4. Differences in concentrations before and after the 1993 flood also were greatest in the upper reach. In pools 1-4, concentrations of pyrene and PCBs decreased after the flood whereas coprostanol increased. These results suggest that bed sediments stored in the pools were diluted or buried by sediments with different organic compound compositions washed in from urban and agricultural portions of the watershed.The 1500 km Upper Mississippi River (UMR) consists of 29 navigation pools and can be divided into the upper reach (pools 1-4), the middle reach (pools 5-13), and the lower reach (pools 14-26). Comparison of composite bed sediment samples collected from the downstream third of 24 pools before and after the 1993 UMR flood provides field-scale data on the effect of the flood on sediment organic compound distributions. The sediments were analyzed for organic carbon, coprostanol, polynuclear aromatic hydrocarbons including pyrene, linear alkylbenzene-sulfonates, polychlorinated biphenyls (PCBs), and organochlorine pesticides. Most of the target compounds were detected in all of the sediment samples, although concentrations were generally <1 mg/kg. The highest concentrations typically occurred in the upper reach, an urbanized area on a relatively small river. Pool 4 (Lake Pepin) is an efficient sediment trap, and concentrations of the compounds below pool 4 were substantially lower than those in pools 2-4. Differences in concentrations before and after the 1993 flood also were greatest in the upper reach. In pools 1-4, concentrations of pyrene and PCBs decreased after the flood whereas coprostanol increased. These results suggest that bed sediments stored in the pools were diluted or buried by sediments with different organic compound compositions washed in from urban and agricultural portions of the watershed.

Microsphere morphology tuning and photo-luminescence properties of monoclinic Y2WO6

NASA Astrophysics Data System (ADS)

Gao, Hong; Bai, Yulong; Zhang, Junying; Tang, Zilong

2015-04-01

Effects of the solution pH value and reaction time on the precursor morphology and photoluminescence properties are investigated for hydrothermally prepared monoclinic Y2WO6 phosphors. In the near-neutral environment, sodium dodecyl benzene sulfonate (SDBS) surfactant forms small microspheres micelles as template to synthesize microspherical precursor. H+ ions concentration affects the arrangement of negative ionic surfactant SDBS. As a result, jujube-liked and popcorn-like loose microspheres formed at low pH value. When the pH value is 5.2 and the hydrothermal reaction time reaches 24 h, respectively, the strongest luminescent intensity can be obtained. Under this condition, the precursor presented regular microsphere with diameter of 4.0 μm. After high-temperature heat treatment, the obtained phosphor particles still exhibit microsphere-like shape. Therefore, we provide an effective method to tune the morphology of Y2WO6 phosphors and study the relationship between morphology and luminescent performance.

Polymerization of anionic wormlike micelles.

PubMed

Zhu, Zhiyuan; González, Yamaira I; Xu, Hangxun; Kaler, Eric W; Liu, Shiyong

2006-01-31

Polymerizable anionic wormlike micelles are obtained upon mixing the hydrotropic salt p-toluidine hydrochloride (PTHC) with the reactive anionic surfactant sodium 4-(8-methacryloyloxyoctyl)oxybenzene sulfonate (MOBS). Polymerization captures the cross-sectional radius of the micelles (approximately 2 nm), induces micellar growth, and leads to the formation of a stable single-phase dispersion of wormlike micellar polymers. The unpolymerized and polymerized micelles were characterized using static and dynamic laser light scattering, small-angle neutron scattering, 1H NMR, and stopped-flow light scattering. Stopped-flow light scattering was also used to measure the average lifetime of the unpolymerized wormlike micelles. A comparison of the average lifetime of unpolymerized wormlike micelles with the surfactant monomer propagation rate was used to elucidate the mechanism of polymerization. There is a significant correlation between the ratio of the average lifetime to the monomer propagation rate and the average aggregation number of the polymerized wormlike micelles.

Fluorescence in the system Eu(III) - oxytetracycline - co-ligand -sodium dodecylbenzene sulphonate micelles and its analytical application

NASA Astrophysics Data System (ADS)

Shtykov, Sergei N.; Smirnova, Tatyana D.; Kalashnikova, Natalja V.; Bylinkin, Yurii G.; Zhemerichkin, Dmitry A.

2006-07-01

Fluorescence enhancement of the Eu 3+ - oxytetracycline (OTC) chelate by addition of phenanthroline (Phen) and trioctyiphosphine oxide (TOPO) as well as micelles of anionic, catiomic and nonionic surfactants has been studied. As was found, in the presence of Phen as co-ligand and micelles of dodecylbenzene sulfonate as anionic surfactant the analytical signal increased by a factor of 8.5 and reached maximum value at pH 8.0 +/- 0.5. The dynamic concentration range of OTC determination was found to be 8.0 x 10 -8 - 4.0 × 10 -5 M (R2 = 0.991) and the detection limit 5.3 × 10 -8 M (3 σ criterion). The procedure based on europium-sensitized fluorescence has been developed for the determination of OTC in chicken meat with the recovery of 98.0-103.3%.

Continuous bioproduction of short-chain fatty acids from sludge enhanced by the combined use of surfactant and alkaline pH.

PubMed

Chen, Yinguang; Liu, Kun; Su, Yinglong; Zheng, Xiong; Wang, Qin

2013-07-01

This work reported the enhancement of continuous SCFA production from sludge by the combined use of surfactant (sodium dodecylbenzene sulfonate (SDBS)) and pH 10 (i.e., SDBS & pH 10). The maximal SCFA production (2056 mg COD/L) was achieved under the SDBS & pH 10 condition at a sludge retention time (SRT) of 12d, which was much higher than that of the blank, sole SDBS, or pH 10. The mechanisms investigation showed that the combined strategy had greater sludge solubilization, higher protein hydrolysis, and lower activity of methanogens. Fluorescence in situ hybridization analysis revealed that the abundance of bacteria was increased, whereas that of archaea was decreased by SDBS & pH 10. The excitation emission matrix fluorescence spectroscopy assay further suggested that SBDS caused protein structure change, which benefited protein hydrolysis. Copyright © 2013 Elsevier Ltd. All rights reserved.

Solution Properties of Dissymmetric Sulfonate-type Anionic Gemini Surfactants.

PubMed

Yoshimura, Tomokazu; Akiba, Kazuki

2016-01-01

Dissymmetric and symmetric anionic gemini surfactants, N-alkyl-N'-alkyl-N,N'dipropanesulfonylethylenediamine (CmCnSul, where m and n represent alkyl chain lengths of m-n = 4-16, 6-14, 8-12, 10-10, and 12-12), were synthesized by two- or three-step reactions. Their physicochemical properties were characterized by equilibrium surface tension measurements, steady-state fluorescence spectroscopy of pyrene, and dynamic light scattering. The critical micelle concentration (CMC) of the dissymmetric surfactants C4C16Sul, C6C14Sul, and C8C12Sul was slightly lower than that of the symmetric surfactant C10C10Sul. The occupied area per molecule (A) of C8C12Sul was smaller than that of C10C10Sul, indicating that C8C12Sul has a high surface activity. However, the increase in the degree of dissymmetry from C8C12Sul to C6C14Sul and then to C4C16Sul resulted in high surface tension and large A. Based on the surface tension, the standard free energies of micellization (∆G°mic) and adsorption (∆G°ads), the efficiency of surface adsorption (pC20), and the effectiveness of surface adsorption (CMC/C20) were obtained. These parameters suggested that C8C12Sul formed micelles more readily than the other surfactants. The properties determined from the surface tension indicated that C8C12Sul's ability is intermediate between those of C10C10Sul and C12C12Sul. The pyrene fluorescence and dynamic light scattering results revealed that the micelle size depends on the longer of the two alkyl chains in dissymmetric surfactants.

The use of long-chain alkylbenzenes and alkyltoluenes for fingerprinting marine oil wastes.

PubMed

Albaigés, Joan; Jimenez, Núria; Arcos, Altamira; Dominguez, Carmen; Bayona, Josep M

2013-04-01

Petroleum long-chain alkylbenzenes and alkyltoluenes are characterized and used for chemical fingerprinting of marine oil spills. Their distributions, extending from C10 to C35 can be used for a general oil type classification. Moreover, the relative distributions of specific components, namely the 3-methyl and 2-methyl-1-alkylbenzenes (m- and o-isomers), and the aryl isoprenoid 1-methyl-3-phytanylbenzene, are proposed as diagnostic markers for source identification. This approach has been exemplified in two case studies involving the spill of bilge oils, where a preliminary screening of the potential source was obtained. Copyright © 2012 Elsevier Ltd. All rights reserved.

Scintillation decay time and pulse shape discrimination in oxygenated and deoxygenated solutions of linear alkylbenzene for the SNO+ experiment

NASA Astrophysics Data System (ADS)

O'Keeffe, H. M.; O'Sullivan, E.; Chen, M. C.

2011-06-01

The SNO+ liquid scintillator experiment is under construction in the SNOLAB facility in Canada. The success of this experiment relies upon accurate characterization of the liquid scintillator, linear alkylbenzene (LAB). In this paper, scintillation decay times for alpha and electron excitations in LAB with 2 g/L PPO are presented for both oxygenated and deoxygenated solutions. While deoxygenation is expected to improve pulse shape discrimination in liquid scintillators, it is not commonly demonstrated in the literature. This paper shows that for linear alkylbenzene, deoxygenation improves discrimination between electron and alpha excitations in the scintillator.

Biodegradation of monoaromatic hydrocarbons by aquifer microorganisms using oxygen, nitrate, or nitrous oxide as the terminal electron acceptor.

PubMed Central

Hutchins, S R

1991-01-01

Microcosms were prepared from aquifer material, spiked with monoaromatic hydrocarbons, and amended with oxygen, nitrate, and nitrous oxide. Benzene and alkylbenzenes were degraded to concentrations below 5 micrograms/liter within 7 days under aerobic conditions, whereas only the alkylbenzenes were degraded when either nitrate or nitrous oxide was used. With limited oxygen, monoaromatic hydrocarbons were degraded but removal ceased once oxygen was consumed. However, when nitrate was also present, biodegradation of the alkylbenzenes continued with no apparent lag. Although benzene was still recalcitrant, levels were reduced compared with levels after treatment with nitrate or limited oxygen alone. PMID:1768110

Land Use Regression Models for Alkylbenzenes in a Middle Eastern Megacity: Tehran Study of Exposure Prediction for Environmental Health Research (Tehran SEPEHR).

PubMed

Amini, Heresh; Schindler, Christian; Hosseini, Vahid; Yunesian, Masud; Künzli, Nino

2017-08-01

Land use regression (LUR) has not been applied thus far to ambient alkylbenzenes in highly polluted megacities. We advanced LUR models for benzene, toluene, ethylbenzene, p-xylene, m-xylene, o-xylene (BTEX), and total BTEX using measurement based estimates of annual means at 179 sites in Tehran megacity, Iran. Overall, 520 predictors were evaluated, such as The Weather Research and Forecasting Model meteorology predictions, emission inventory, and several new others. The final models with R 2 values ranging from 0.64 for p-xylene to 0.70 for benzene were mainly driven by traffic-related variables but the proximity to sewage treatment plants was present in all models indicating a major local source of alkylbenzenes not used in any previous study. We further found that large buffers are needed to explain annual mean concentrations of alkylbenzenes in complex situations of a megacity. About 83% of Tehran's surface had benzene concentrations above air quality standard of 5 μg/m 3 set by European Union and Iranian Government. Toluene was the predominant alkylbenzene, and the most polluted area was the city center. Our analyses on differences between wealthier and poorer areas also showed somewhat higher concentrations for the latter. This is the largest LUR study to predict all BTEX species in a megacity.

Micellar electrokinetic chromatography with acid labile surfactant.

PubMed

Stanley, Bob; Lucy, Charles A

2012-02-24

We present a study of a degradable surfactant, sodium 4-[(2-methyl-2-undecyl-1,3-dioxolan-4-yl)methoxy]-1-propane sulfonate that is also known as an acid-labile surfactant (ALS). The performance of ALS as a pseudostationary phase is assessed and compared with established pseudostationary phases such as sodium dodecyl sulphate (SDS), volatile surfactants and polymeric micelles. ALS achieves separation efficiency of 100,000-145,000 theoretical plates and relative standard deviation (RSD) of electrophoretic mobility (n=5) of less than 3%. Retention factors with ALS are strongly correlated with those with SDS. This is shown by the R2=0.79 for all eleven analytes and an R2=0.992 for specifically the non-hydrogen bonding (NHB) analytes. However, ALS displays different selectivity than SDS for hydrogen bond donor (HBD) and hydrogen bond acceptor (HBA) solutes (R2 of 0.74 and 0.88, respectively). ALS is degraded to less surface active compounds in acidic solution. These less surface-active compounds are more compatible with the electrospray ionization mass spectrometry (ESI-MS). ALS has a half-life of 48 min at pH 4. ALS has the potential to couple micellar electrokinetic chromatography (MEKC) with the ESI-MS. ALS can be used as a pseudostationary phase for a high efficiency separation and later acid hydrolyzed to enable an ESI-MS analysis. Copyright © 2011 Elsevier B.V. All rights reserved.

Polythiophene nanocomposites as high performance electrode material for supercapacitor application

NASA Astrophysics Data System (ADS)

Vijeth, H.; Niranjana, M.; Yesappa, L.; Ashokkumar, S. P.; Devendrappa, H.

2018-04-01

A polythiophene-aluminium oxide nanocomposite is prepared by in situ chemical polymerisation in presence of anionic surfactant camphor sulfonic acid (CSA). The characterisation of nano composite was done by X-ray Diffraction (XRD), surface morphology was studied using Atomic Force Microscopy (AFM). The electrochemical performance is evaluated using cyclic voltammetry in 1M H2SO4. As an electroactive material, it exhibits high specific capacitance of 654.5 and 757 F/g for PTH and PTHA nanocomposites at scan rate of 30mV s-1 respectively.

Ellipsometric measurements of the refractive indices of linear alkylbenzene and EJ-301 scintillators from 210 to 1000 nm

NASA Astrophysics Data System (ADS)

Tseung, H. Wan Chan; Tolich, N.

2011-09-01

We report on ellipsometric measurements of the refractive indices of linear alkylbenzene-2,5-diphenyloxazole (LAB-PPO), Nd-doped LAB-PPO and EJ-301 scintillators to the nearest ± 0.005, in the wavelength range 210-1000 nm.

Effect of gamma-ray irradiation at low doses on the performance of PES ultrafiltration membrane

NASA Astrophysics Data System (ADS)

Zhang, Xue; Niu, Lixia; Li, Fuzhi; Yu, Suping; Zhao, Xuan; Hu, Hongying

2016-10-01

The influence of gamma irradiation on the performance of polyether sulfone (PES) ultrafiltration (UF) membrane was investigated at low absorbed doses (0-75 kGy) using a cobalt source. The performance of the UF membranes was tested using low level radioactive wastewater (LLRW) containing three types of surfactants (anionic, cationic and nonionic surfactants). The physical and chemical properties of membrane surface were analyzed, and relationships between these properties and separation performance and fouling characteristics were determined. At 10-75 kGy irradiation, there were no significant changes observed in the membrane surface roughness or polymer functional groups, however the contact angle decreased sharply from 92° to ca. 70° at irradiation levels as low as 10 kGy. When membranes were exposed to the surfactant-containing LLRW, the flux decreased more sharply for higher dosed irradiated membranes, while flux in virgin membranes increased during the filtration processes. The study highlights that fouling properties of membrane may be changed due to the changes of surface hydrophilicity at low dose irradiation, while other surface properties and retentions remain stable. Therefore, a membrane fouling test with real or simulated wastewater is recommended to fully evaluate the membrane irradiation resistance.

Development of Food-Grade Curcumin Nanoemulsion and its Potential Application to Food Beverage System: Antioxidant Property and In Vitro Digestion.

PubMed

Joung, Hee Joung; Choi, Mi-Jung; Kim, Jun Tae; Park, Seok Hoon; Park, Hyun Jin; Shin, Gye Hwa

2016-03-01

Curcumin nanoemulsions (Cur-NEs) were developed with various surfactant concentrations by using high pressure homogenization and finally applied to the commercial milk system. Characterization of Cur-NEs was performed by measuring the droplet size and polydispersity index value at different Tween 20 concentrations. The morphology of the Cur-NEs was observed by confocal laser scanning microscopy and transmission electron microscopy. Antioxidant activity and in vitro digestion ability were tested using 2,2-diphenyl-1-picrylhydrazyl, 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) diammonium salt, pH-stat method, and thiobarbituric acid reactive substances assays. Cur-NEs were found to be physically stable for 1 mo at room temperature. The surfactant concentration affects particle formation and droplet size. The mean droplet size decreased from 122 to 90 nm when surfactant concentration increased 3 times. Cur-NEs had shown an effective oxygen scavenging activity. Cur-NEs-fortified milk showed significantly lower lipid oxidation than control (unfortified) milk and milk containing curcumin-free nanoemulsions. These properties make Cur-NEs suitable systems for the beverage industry. © 2016 Institute of Food Technologists®

Dye-binding protein assay using a long-wave-absorbing cyanine probe.

PubMed

Zheng, Hong; Mao, Yu Xia; Li, Dong Hui; Zhu, Chang Qing

2003-07-01

A simple and fast protein assay that involves the binding of water-soluble sulfonate heptamethylene cyanine to protein is described. The binding of the dye to protein causes a shift in the absorption maximum of the dye from 778 to 904 nm, and the increase in absorption at 904 nm is monitored. This assay is very reproducible, of good color stability for at least 80 min, and sensitive at the 100 ng/mL level of human serum albumin (HSA) when a spectrophotometer with near-infrared wavelength is used to measure absorbance. Few chemicals except ionic surfactants such as cetyltrimethylammonium bromide and sodium dodecyl sulfonate interfere with the assay. Purified proteins have different capacities to interact with the dye; under the experimental conditions, the linear ranges of bovine serum albumin (BSA), HSA and gamma-IgG were 200-2000, 100-2400, and 200-3000 ng/mL, respectively. The relative standard deviation for the five replicate determinations of 1200 ng/mL BSA is 2.1%.

Graphene/activated carbon supercapacitors with sulfonated-polyetheretherketone as solid-state electrolyte and multifunctional binder

NASA Astrophysics Data System (ADS)

Chen, Y.-R.; Chiu, K.-F.; Lin, H. C.; Chen, C.-L.; Hsieh, C. Y.; Tsai, C. B.; Chu, B. T. T.

2014-11-01

Sulfonated polyetheretherketone (SPEEK) has been synthesised by sulphonation process and used as the solid-state electrolyte, binder and surfactant for supercapacitors. Reduced graphene dispersed by SPEEK is used as a high-efficiency conducting additive in solid-state supercapacitors. It is found that SPEEK can improve the stability of the reduced graphene dispersion significantly, and therefore, the solid-state supercapacitors show a large decrease in IR drop and charge-transfer resistance (Rct), resulting in a higher rate capability. The solid-state supercapacitors with the activated carbon/reduced graphene/SPEEK/electrode can be operated from 1 to 8 A/g and exhibit capacity retention of 93%. The noteworthy is more than twice higher value for capacity retention by comparison with the solid-state supercapacitors using activated carbon/reduced graphene/PVDF electrode (capacity retention is 36%). The cell of reduced graphene with SPEEK can be cycled over 5000 times at 5 A/g with no capacitance fading.

Perfluorooctane Sulfonate Plasma Half-Life Determination and Long-Term Tissue Distribution in Beef Cattle (Bos taurus).

PubMed

Lupton, Sara J; Dearfield, Kerry L; Johnston, John J; Wagner, Sarah; Huwe, Janice K

2015-12-30

Perfluorooctane sulfonate (PFOS) is used in consumer products as a surfactant and is found in industrial and consumer waste, which ends up in wastewater treatment plants (WWTPs). PFOS does not breakdown during WWTP processes and accumulates in the biosolids. Common practices include application of biosolids to pastures and croplands used for feed, and as a result, animals such as beef cattle are exposed to PFOS. To determine plasma and tissue depletion kinetics in cattle, 2 steers and 4 heifers were dosed with PFOS at 0.098 mg/kg body weight and 9.1 mg/kg, respectively. Plasma depletion half-lives for steers and heifers were 120 ± 4.1 and 106 ± 23.1 days, respectively. Specific tissue depletion half-lives ranged from 36 to 385 days for intraperitoneal fat, back fat, muscle, liver, bone, and kidney. These data indicate that PFOS in beef cattle has a sufficiently long depletion half-life to permit accumulation in edible tissues.

Effect of CaCl2 on the property of an anionic surfactant monolayer formed at the air/water interface: a molecular dynamics study

NASA Astrophysics Data System (ADS)

Zhang, Tiantian; You, Jing; Yu, Jiliang; Fan, Chengcheng; Ma, Yunfei; Cui, Yanjie; Gao, Shanshan; Li, Yongbin; Hu, Songqing; Liu, Huiqin

2017-12-01

Molecular dynamics simulation had been carried out to investigate the influence of CaCl2 on the aggregation behaviour of sodium dodecyl polyoxyethylene sulfonate (A12E2SO3) at the air/water interface. First, structure properties of A12E2SO3 monolayer was studied by analyzing the snapshots of the configuration and density profiles of different components in A12E2SO3 systems. Results showed that Ca2+ could replace some Na+ to combine with the hydrophilic headgroups. Besides, the addition of CaCl2 could reduce the thickness of water layer at the interface. Second, the interactions between A12E2SO3 headgroups and water molecules were studied through calculating radial distribution functions (RDFs) between water molecules and the sulfonate group, as well as the oxyethyl group. Results revealed that Ca2+ could penetrate the hydration layer of the sulfonate group, but could not enter the first hydration layer of the oxygen ethyl group close to the sulfonate group. The addition of CaCl2 could make the degree of hydration more orderly and the thickness of hydration layer in the headgroups of A12E2SO3 molecules increase. Third, the property of interface double layer was studied through analyzing RDFs of the headgroups and counterions. Results showed that the addition of CaCl2 could not only reduce the interaction between the headgroups and the counterions, but also compress the thickness of the electric double layer in A12E2SO3 system.

Evaluation of anionic surfactant concentrations in US effluents and probabilistic determination of their combined ecological risk in mixing zones.

PubMed

McDonough, Kathleen; Casteel, Kenneth; Itrich, Nina; Menzies, Jennifer; Belanger, Scott; Wehmeyer, Kenneth; Federle, Thomas

2016-12-01

Alcohol sulfates (AS), alcohol ethoxysulfates (AES), linear alkyl benzenesulfonates (LAS) and methyl ester sulfonates (MES) are anionic surfactants that are widely used in household detergents and consumer products resulting in over 1 million tons being disposed of down the drain annually in the US. A monitoring campaign was conducted which collected grab effluent samples from 44 wastewater treatment plants (WWTPs) across the US to generate statistical distributions of effluent concentrations for anionic surfactants. The mean concentrations for AS, AES, LAS and MES were 5.03±4.5, 1.95±0.7, 15.3±19, and 0.35±0.13μg/L respectively. Since each of these surfactants consist of multiple homologues that differ in their toxicity, the concentration of each homologue measured in an effluent sample was converted into a toxic unit (TU) by normalizing to the predicted no effect concentration (PNEC) derived from high tier effects data (mesocosm studies). The statistical distributions of the combined TUs in the effluents were used in combination with distributions of dilution factors for WWTP mixing zones to conduct a US-wide probabilistic risk assessment for the aquatic environment for each of the surfactants. The 90th percentile level of TUs for AS, AES, LAS and MES in mixing zones were 1.89×10 -2 , 2.73×10 -3 , 2.72×10 -2 , and 3.65×10 -5 under 7Q10 (lowest river flow occurring over a 7day period every 10years) low flow conditions. Because these surfactants have the same toxicological mode of action, the TUs were summed and the aquatic safety for anionic surfactants as a whole was assessed. At the 90th percentile level under the conservative 7Q10 low flow conditions the forecasted TUs were 4.21×10 -2 which indicates that there is a significant margin of safety for the class of anionic surfactants in US aquatic environments. Copyright © 2016 Elsevier B.V. All rights reserved.

Aqueous solubilities, vapor pressures, and 1-octanol-water partition coefficients for C9-C14 linear alkylbenzenes

USGS Publications Warehouse

Sherblom, P.M.; Gschwend, P.M.; Eganhouse, R.P.

1992-01-01

Measurements and estimates of aqueous solubilities, 1-octanol-water partition coefficients (Kow), and vapor pressures were made for 29 linear alkylbenzenes having alkyl chain lengths of 9-14 carbons. The ranges of values observed were vapor pressures from 0.002 to 0.418 Pa, log Kow, from 6.83 to 9.95, and aqueous solubilities from 4 to 38 nmol??L-1. Measured values exhibited a relationship to both the alkyl chain length and the position of phenyl substitution on the alkyl chain. Measurement of the aqueous concentrations resulting from equilibration of a mixture of alkylbenzenes yielded higher than expected values, indicating cosolute or other interactive effects caused enhanced aqueous concentrations of these compounds. ?? 1992 American Chemical Society.

Killing of preimplantation mouse embryos by main ingredients of cleansers AS and LAS.

PubMed

Nomura, T; Hata, S; Shibata, K; Kusafuka, T

1987-01-01

When main ingredients of cleansers, alcohol sulfate (AS) and linear alkylbenzene sulfonate (LAS), were applied to the dorsal skin of pregnant JCL:ICR mice during preimplantation period (days 0-2), significant numbers of embryos collected from the oviducts and uteri on day 3 showed severe deformity or remained at the morula stage. Most of abnormal embryos were fragmented or remained at the 1-8 cell stages, and they were either dead or dying. Even when these abnormal embryos were cultivated in the detergent-free medium, they were not recovered, while most growth-retarded embryos (morula) could grow and hatch with one or two days lag by the further in vitro cultivation. Similar results were observed with commercially obtained kitchen detergent and hair shampoo, although such embryocidal effects were not detected with natural soap and distilled water. Fertilized eggs may be specifically sensitive to synthetic detergents. Very low doses of X-rays also induced significant yields of abnormal embryos. Major difference between X-rays and detergents was that X-ray-induced abnormality appeared at the morula or blastocyst stage, while detergent-induced one did at the earlier stages.

Layer-by-Layer Assembly of Fluorine-Free Polyelectrolyte-Surfactant Complexes for the Fabrication of Self-Healing Superhydrophobic Films.

PubMed

Wu, Mengchun; An, Ni; Li, Yang; Sun, Junqi

2016-11-29

Fluorine-free self-healing superhydrophobic films are of significance for practical applications because of their extended service life and cost-effective and eco-friendly preparation process. In this study, we report the fabrication of fluorine-free self-healing superhydrophobic films by layer-by-layer (LbL) assembly of poly(sodium 4-styrenesulfonate) (PSS)-1-octadecylamine (ODA) complexes (PSS-ODA) and poly(allylamine hydrochloride) (PAH)-sodium dodecyl sulfonate (SDS) (PAH-SDS) complexes. The wettability of the LbL-assembled PSS-ODA/PAH-SDS films depends on the film structure and can be tailored by changing the NaCl concentration in aqueous dispersions of PSS-ODA complexes and the number of film deposition cycles. The freshly prepared PSS-ODA/PAH-SDS film with micro- and nanoscaled hierarchical structures is hydrophilic and gradually changes to superhydrophobic in air because the polyelectrolyte-complexed ODA and SDS surfactants tend to migrate to the film surface to cover the film with hydrophobic alkyl chains to lower its surface energy. The large amount of ODA and SDS surfactants loaded in the superhydrophobic PSS-ODA/PAH-SDS films and the autonomic migration of these surfactants to the film surface endow the resultant superhydrophobic films with an excellent self-healing ability to restore the damaged superhydrophobicity. The self-healing superhydrophobic PSS-ODA/PAH-SDS films are mechanically robust and can be deposited on various flat and nonflat substrates. The LbL assembly of oppositely charged polyelectrolyte-surfactant complexes provides a new way for the fabrication of fluorine-free self-healing superhydrophobic films with satisfactory mechanical stability, enhanced reliability, and extended service life.

Facile controlled synthesis of micro/nanostructure MCrO 4 (M = Ba, Pb) by using Gemini surfactant C 12-PEG-C 12 as a soft template

NASA Astrophysics Data System (ADS)

Chang, Wengui; Shen, Yuhua; Xie, Anjian; Liu, Xue

2010-04-01

Gemini surfactants, double sodium α-sulfonic polyethylene glycol laurate (abbreviated C 12-PEG-C 12), were prepared and applied as soft templates in the controlled synthesis of BaCrO 4 and PbCrO 4 micro/nanocrystals. The template effects were investigated by adjusting the length of the spacer, using PEG400 and PEG4000, of the Gemini surfactant. The results indicated that the size and morphology of BaCrO 4 and PbCrO 4 micro/nanocrystals varied with the change in spacer length of C 12-PEG-C 12, suggesting that the different lengths of the polyethylene glycol group spacers in the Gemini surfactants played a key role in determining the size and shape of the MCrO 4 micro/nanoparticles. The dynamic process of the formation of the novel morphology BaCrO 4 crystals showed that the morphology grew from a round-bar polyhedron, to regular polyhedron, to approximate octahedron to a uniform pistachio nut shape. The growth mechanism of the BaCrO 4 micro/nanocrystals was explained that C 12-PEG-C 12 had a greater interfacial adsorption and would effectively control the shape evolution during the crystal growth, while PbCrO 4 could be explained that the Gemini surfactants can undergo liquid-crystalline phase transitions with long channels providing a soft template effect and derived the nanorods formation. Room temperature fluorescence spectra were studied and these showed that the pistachio-shaped BaCrO 4 microcrystals and PbCrO 4 nanorods possess photoactive luminescence properties with emission peaks at 470 and 549 nm, respectively.

Pore Scale Dynamics of Microemulsion Formation.

PubMed

Unsal, Evren; Broens, Marc; Armstrong, Ryan T

2016-07-19

Experiments in various porous media have shown that multiple parameters come into play when an oleic phase is displaced by an aqueous solution of surfactant. In general, the displacement efficiency is improved when the fluids become quasi-miscible. Understanding the phase behavior oil/water/surfactant systems is important because microemulsion has the ability to generate ultralow interfacial tension (<10(-2) mN m(-1)) that is required for miscibility to occur. Many studies focus on microemulsion formation and the resulting properties under equilibrium conditions. However, the majority of applications where microemulsion is present also involve flow, which has received relatively less attention. It is commonly assumed that the characteristics of an oil/water/surfactant system under flowing conditions are identical to the one under equilibrium conditions. Here, we show that this is not necessarily the case. We studied the equilibrium phase behavior of a model system consisting of n-decane and an aqueous solution of olefin sulfonate surfactant, which has practical applications for enhanced oil recovery. The salt content of the aqueous solution was varied to provide a range of different microemulsion compositions and oil-water interfacial tensions. We then performed microfluidic flow experiments to study the dynamic in situ formation of microemulsion by coinjecting bulk fluids of n-decane and surfactant solution into a T-junction capillary geometry. A solvatochromatic fluorescent dye was used to obtain spatially resolved compositional information. In this way, we visualized the microemulsion formation and the flow of it along with the excess phases. A complex interaction between the flow patterns and the microemulsion properties was observed. The formation of microemulsion influenced the flow regimes, and the flow regimes affected the characteristics of the microemulsion formation. In particular, at low flow rates, slug flow was observed, which had profound consequences on the pore scale mixing behavior and resulting microemulsion properties.

Water-soluble conductive polymers

DOEpatents

Aldissi, Mahmoud

1989-01-01

Polymers which are soluble in water and are electrically conductive. The monomer repeat unit is a thiophene or pyrrole molecule having an alkyl group substituted for the hydrogen atom located in the beta position of the thiophene or pyrrole ring and having a surfactant molecule at the end of the alkyl chain. Polymers of this class having 8 or more carbon atoms in the alkyl chain exhibit liquid crystalline behavior, resulting in high electrical anisotropy. The monomer-to-monomer bonds are located between the carbon atoms which are adjacent to the sulfur or nitrogen atoms. The number of carbon atoms in the alkyl group may vary from 1 to 20 carbon atoms. The surfactant molecule consists of a sulfonate group, or a sulfate group, or a carboxylate group, and hydrogen or an alkali metal. Negative ions from a supporting electrolyte which may be used in the electrochemical synthesis of a polymer may be incorporated into the polymer during the synthesis and serve as a dopant to increase the conductivity.

Water-soluble conductive polymers

DOEpatents

Aldissi, Mahmoud

1990-01-01

Polymers which are soluble in water and are electrically conductive. The monomer repeat unit is a thiophene or pyrrole molecule having an alkyl group substituted for the hydrogen atom located in the beta position of the thiophene or pyrrole ring and having a surfactant molecule at the end of the alkyl chain. Polymers of this class having 8 or more carbon atoms in the alkyl chain exhibit liquid crystalline behavior, resulting in high electrical anisotropy. The monomer-to-monomer bonds are located between the carbon atoms which are adjacent to the sulfur or nitrogen atoms. The number of carbon atoms in the alkyl group may vary from 1 to 20 carbon atoms. The surfactant molecule consists of a sulfonate group, or a sulfate group, or a carboxylate group, and hydrogen or an alkali metal. Negative ions from a supporting electrolyte which may be used in the electrochemical synthesis of a polymer may be incorporated into the polymer during the synthesis and serve as a dopant to increase the conductivity.

Water-soluble conductive polymers

DOEpatents

Aldissi, M.

1988-02-12

Polymers which are soluble in water and are electrically conductive. The monomer repeat unit is a thiophene or pyrrole molecule having an alkyl group substituted for the hydrogen atom located in the beta position of the thiophene or pyrrole ring and having a surfactant molecule at the end of the alkyl chain. Polymers of this class having 8 or more carbon atoms in the alkyl chain exhibit liquid crystalline behavior, resulting in high electrical anisotropy. The monomer-to-monomer bonds are located between the carbon atoms which are adjacent to the sulfur or nitrogen atoms. The number of carbon atoms in the alkyl group may vary from 1 to 20 carbon atoms. The surfactant molecule consists of a sulfonate group, or a sulfate group, or a carboxylate group, and hydrogen or an alkali metal. Negative ions from a supporting electrolyte which may be used in the electrochemical synthesis of a polymer may be incorporated into the polymer during the synthesis and serve as a dopant to increase the conductivity.

Effects of surfactants on the formation of gelatin nanofibres for controlled release of curcumin.

PubMed

Deng, Lingli; Kang, Xuefan; Liu, Yuyu; Feng, Fengqin; Zhang, Hui

2017-09-15

This work studied the effects of non-ionic Tween 80, anionic sodium dodecyl sulfonate (SDS) and cationic cetyltrimethyl ammonium bromide (CTAB) surfactants on the morphology of electrospun gelatin nanofibres, and on the release behaviour, antioxidant activity and antimicrobial activity of encapsulated curcumin. Scanning electron micrographs showed that addition of SDS significantly increased the nanofibre diameter. Fourier transform infrared and differential scanning calorimetry analysis indicated that gelatin and SDS intimately interacted via electrostatic and hydrophobic interactions. However, these interactions inhibited the release of curcumin from the nanofibres with SDS, while CTAB and Tween 80 both facilitated the release. SDS and Tween 80 showed protective effects on curcumin from the attack of 2,2-diphenyl-1-picryl-hydrazyl-hydrate (DPPH) radicals, and the increased release of curcumin from nanofibres with CTAB or Tween 80 resulted in a higher reducing power. The antimicrobial activity results suggested that the curcumin encapsulated gelatin nanofibres with CTAB exhibited effective inhibition against Staphylococcus aureus. Copyright © 2017 Elsevier Ltd. All rights reserved.

Transport and fate of organic wastes in groundwater at the Stringfellow hazardous waste disposal site, southern California

USGS Publications Warehouse

Leenheer, J.A.; Hsu, J.; Barber, L.B.

2001-01-01

In January 1999, wastewater influent and effluent from the pretreatment plant at the Stringfellow hazardous waste disposal site were sampled along with groundwater at six locations along the groundwater contaminant plume. The objectives of this sampling and study were to identify at the compound class level the unidentified 40-60% of wastewater organic contaminants, and to determine what organic compound classes were being removed by the wastewater pretreatment plant, and what organic compound classes persisted during subsurface waste migration. The unidentified organic wastes are primarily chlorinated aromatic sulfonic acids derived from wastes from DDT manufacture. Trace amounts of EDTA and NTA organic complexing agents were discovered along with carboxylate metabolites of the common alkylphenolpolyethoxylate plasticizers and nonionic surfactants. The wastewater pretreatment plant removed most of the aromatic chlorinated sulfonic acids that have hydrophobic neutral properties, but the p-chlorobenzenesulfonic acid which is the primary waste constituent passed through the pretreatment plant and was discharged in the treated wastewaters transported to an industrial sewer. During migration in groundwater, p-chlorobenzenesulfonic acid is removed by natural remediation processes. Wastewater organic contaminants have decreased 3- to 45-fold in the groundwater from 1985 to 1999 as a result of site remediation and natural remediation processes. The chlorinated aromatic sulfonic acids with hydrophobic neutral properties persist and have migrated into groundwater that underlies the adjacent residential community. Copyright ?? 2001 .

Investigation of polar and stereoelectronic effects on pure excited-state hydrogen atom abstractions from phenols and alkylbenzenes.

PubMed

Pischel, Uwe; Patra, Digambara; Koner, Apurba L; Nau, Werner M

2006-01-01

The fluorescence quenching of singlet-excited 2,3-diazabicyclo[2.2.2]oct-2-ene (DBO) by 22 phenols and 12 alkylbenzenes has been investigated. Quenching rate constants in acetonitrile are in the range of 10(8)-10(9) M(-1)s(-1) for phenols and 10(5)-10(6) M(-1)s(-1) for alkylbenzenes. In contrast to the quenching of triplet-excited benzophenone, no exciplexes are involved, so that a pure hydrogen atom transfer is proposed as quenching mechanism. This is supported by (1) pronounced deuterium isotope effects (kH/kD ca 4-6), which were observed for phenols and alkylbenzenes, and (2) a strongly endergonic thermodynamics for charge transfer processes (electron transfer, exciplex formation). In the case of phenols, linear free energy relationships applied, which led to a reaction constant of rho = -0.40, suggesting a lower electrophilicity of singlet-excited DBO than that of triplet-excited ketones and alkoxyl radicals. The reactivity of singlet-excited DBO exposes statistical, steric, polar and stereoelectronic effects on the hydrogen atom abstraction process in the absence of complications because of competitive exciplex formation.

Investigating the effectiveness of the surfactant dioctyl sodium sulfosuccinate to disperse oil in a changing marine environment

NASA Astrophysics Data System (ADS)

Steffy, David A.; Nichols, Alfred C.; Kiplagat, George

2011-12-01

We investigated the surfactant dioctyl sodium sulfosuccinate (DOSS) and its delivery system Corexit 9500A, used to disperse oil released during the Gulf of Mexico spill during the summer of 2010. DOSS is an organic sulfonic acid salt that acts as a synthetic detergent and disrupts the interfacial tension between the salt water and crude oil phases. The disruption reaches a maximum at or above the critical micelle concentration (CMC). The CMC for the surfactant was determined to be 0.17% solution in deionized water at a pH of 7.2 and a temperature of 21.1 °C (70°F). The CMC is lower in salt water, at 0.125% solution. This has been identified as a "salting out" effect (Somasundaran, 2006). The CMC of DOSS in both saline and deionized water occurred at lower-percent solutions at higher temperatures. The surface tension versus concentration plots can be modeled using a power equation, with correlation coefficients consistently over 0.94. Surface tension versus concentration plots are scalable to fit the desired temperature by the function f(x) = (1/1+Xα), where α =T1/T2. Tests measured the stability of the DOSS micelles when exposed to a continuous UVA radiation. This photodegradation is directly related to the duration of exposure.

Thermochemistry of the specific binding of C12 surfactants to bovine serum albumin.

PubMed

Nielsen, A D; Borch, K; Westh, P

2000-06-15

The specific binding to bovine serum albumin (BSA) of anionic and non-ionic surfactants with C12 acyl chains has been studied by high sensitivity isothermal titration calorimetry. This method proved particularly effective in resolving the binding of anionic surfactants into separate classes of sites with different affinity. For sodium dodecylsulfate (SDS) the measured binding curves could be rationalized as association to two classes (high affinity/low affinity) of sites comprising, respectively, three and six similar (i.e. thermodynamically equivalent), independent sites. Changes in the thermodynamic functions enthalpy, standard free energy, standard entropy and heat capacity could be discerned for each class of binding site, as well as for micelle formation. These data suggest that binding to low affinity sites (in analogy with micelle formation) exhibits energetic parameters; in particular, a large negative change in heat capacity, which is characteristic of hydrophobic interactions. The thermodynamics of high affinity binding, on the other hand, is indicative of other dominant forces; most likely electrostatic interactions. Other anionic ligands investigated (laurate and dodecyl benzylsulfonate) showed a behavior similar to SDS, the most significant difference being the high affinity binding of the alkylbenzyl sulfonate. For this ligand, the thermodynamic data is indicative of a more loosely associated complex than for SDS and laurate. BSA was found to bind one or two of the non-ionic surfactants (NIS) hepta- or penta(ethylene glycol) monododecyl ether (C12EO7 and C12EO5) with binding constants about three orders of magnitude lower than for SDS. Hence, the free energy of the surfactant in the weakly bound BSA-NIS complex is only slightly favored over the micellar state. The binding process is characterized by very large exothermic enthalpy changes (larger than for the charged surfactants) and a large, positive increment in heat capacity. These observations cannot be reconciled with a molecular picture based on simple hydrophobic condensation onto non-polar patches on the protein surface.

Lateral transport of solutes in microfluidic channels using electrochemically generated gradients in redox-active surfactants.

PubMed

Liu, Xiaoyang; Abbott, Nicholas L

2011-04-15

We report principles for a continuous flow process that can separate solutes based on a driving force for selective transport that is generated by a lateral concentration gradient of a redox-active surfactant across a microfluidic channel. Microfluidic channels fabricated with gold electrodes lining each vertical wall were used to electrochemically generate concentration gradients of the redox-active surfactant 11-ferrocenylundecyl-trimethylammonium bromide (FTMA) in a direction perpendicular to the flow. The interactions of three solutes (a hydrophobic dye, 1-phenylazo-2-naphthylamine (yellow AB), an amphiphilic molecule, 2-(4,4-difluoro-5,7-dimethyl-4-bora-3a,4a-diaza-s-indacene-3-pentanoyl)-1-hexadecanoyl-sn-glycero-3-phosphocholine (BODIPY C(5)-HPC), and an organic salt, 1-methylpyridinium-3-sulfonate (MPS)) with the lateral gradients in surfactant/micelle concentration were shown to drive the formation of solute-specific concentration gradients. Two distinct physical mechanisms were identified to lead to the solute concentration gradients: solubilization of solutes by micelles and differential adsorption of the solutes onto the walls of the microchannels in the presence of the surfactant concentration gradient. These two mechanisms were used to demonstrate delipidation of a mixture of BODIPY C(5)-HPC (lipid) and MPS and purification of BODIPY C(5)-HPC from a mixture of BODIPY C(5)-HPC and yellow AB. Overall, the results of this study demonstrate that lateral concentration gradients of redox-active surfactants formed within microfluidic channels can be used to transport solutes across the microfluidic channels in a solute-dependent manner. The approach employs electrical potentials (<1 V) that are sufficiently small to avoid electrolysis of water, can be performed in solutions having high ionic strength (>0.1M), and offers the basis of continuous processes for the purification or separation of solutes in microscale systems. © 2011 American Chemical Society

Emulsification kinetics during quasi-miscible flow in dead-end pores

NASA Astrophysics Data System (ADS)

Broens, M.; Unsal, E.

2018-03-01

Microemulsions have found applications as carriers for the transport of solutes through various porous media. They are commonly pre-prepared in bulk form, and then injected into the medium. The preparation is done by actively mixing the surfactant, water and oil, and then allowing the mixture to stagnate until equilibrium is reached. The resulting microemulsion characteristics of the surfactant/oil/water system are studied at equilibrium conditions, and perfect mixing is assumed. But in applications like subsurface remediation and enhanced oil recovery, microemulsion formation may occur in the pore space. Surfactant solutions are injected into the ground to solubilize and/or mobilize the non-aqueous phase liquids (NAPLs) by in-situ emulsification. Flow dynamics and emulsification kinetics are coupled, which also contributes to in-situ mixing. In this study, we investigated the nature of such coupling for a quasi-miscible fluid system in a conductive channel with dead-end extensions. A microfluidic setup was used, where an aqueous solution of an anionic, internal olefin sulfonate 20-24 (IOS) surfactant was injected into n-decane saturated glass micromodel. The oil phase was coloured using a solvatochromatic dye allowing for direct visualization of the aqueous and oil phases as well as their microemulsions under fluorescent light. Presence of both conductive and stagnant dead-end channels in a single pore system made it possible to isolate different transport mechanisms from each other but also allowed to study the transitions from one to the other. In the conductive channel, the surfactant was carried with flow, and emulsification was controlled by the localized flow dynamics. In the stagnant zones, the driving force of the mass transfer was driven by the chemical concentration gradient. Some of the equilibrium phase behaviour characteristics of the surfactant/oil/water system were recognisable during the quasi-miscible displacement. However, the equilibrium tests alone were not sufficient to predict the emulsification process under dynamic conditions.

Diagenetic fate of organic contaminants on the Palos Verdes Shelf, California

USGS Publications Warehouse

Eganhouse, R.P.; Pontolillo, J.; Leiker, T.J.

2000-01-01

Municipal wastes discharged through deepwater submarine outfalls since 1937 have contaminated sediments of the Palos Verdes Shelf. A site approximately 6-8 km downcurrent from the outfall system was chosen for a study of the diagenetic fate of organic contaminants in the waste-impacted sediments. Concentrations of three classes of hydrophobic organic contaminants (DDT + metabolites, polychlorinated biphenyls (PCBs), and the long-chain alkylbenzenes) were determined in sediment cores collected at the study site in 1981 and 1992. Differences between the composition of effluent from the major source of DDT (Montrose Chemical) and that found in sediments suggests that parent DDT was transformed by hydrolytic dehydrochlorination during the earliest stages of diagenesis. As a result, p,p'-DDE is the dominant DDT metabolite found in shelf sediments, comprising 60-70% of ??DDT. The p,p-DDE/p,p'-DDMU concentration ratio decreases with increasing sub-bottom depth in sediment cores, indicating that reductive dechlorination of p,p'-DDE is occurring. Approximately 9-23% of the DDE inventory in the sediments may have been converted to DDMU since DDT discharges began ca. 1953. At most, this is less than half of the decline in p,p'-DDE inventory that has been observed at the study site for the period 1981-1995. Most of the observed decrease is attributable to remobilization by processes such as sediment mixing coupled to resuspension, contaminant desorption, and current advection. Existing field data suggest that the in situ rate of DDE transformation is 102-103 times slower than rates determined in recent laboratory microcosm experiments (Quensen, J.F., Mueller, S.A., Jain, M.K., Tiedje, J.M., 1998. Reductive dechlorination of DDE to DDMU in marine sediment microcosms. Science, 280, 722-724.). This explains why the DDT composition (i.e. o,p'-, p,p'-isomers of DDE, DDD, DDT) of sediments from this site have not changed significantly since at least 1972. Congener-specific PCB compositions in shelf sediments are highly uniform and show no evidence of diagenetic transformation. Apparently, the agents/factors responsible for reductive dechlorination of DDE are not also effecting alteration of the PCBs. Two types of long-chain alkylbenzenes were found in the contaminated sediments. Comparison of chain length and isomer distributions of the linear alkylbenzenes in wastewater effluent and surficial sediment samples indicate that these compounds undergo biodegradation during sedimentation. Further degradation of the linear alkylbenzenes occurs after burial despite relatively invariant isomer compositions. The branched alkylbenzenes are much more persistent than the linear alkylbenzenes, presumably due to extensive branching of the alkyl side chain. Based on these results, p,p'-DDE, PCBs, and selected branched alkylbenzenes are sufficiently persistent for use in molecular stratigraphy. The linear alkylbenzenes may also provide information on depositional processes. However, their application as quantitative molecular tracers should be approached with caution.

[Identification of alkylbenzenes being formed in the model reaction of ribose with lysine].

PubMed

Biller, Elzbieta

2012-01-01

While studying volatile compounds in model experiments which simulated the broiling of meat (the reactions of ribose with lysine), there were alkylbenzenes identified. They belong to food contaminants and they could be originated from the detergents and petroleum as well as geochemical samples, but they were also obtained in Maillard reactions. The aim of the studies was the attempt of the alkylbenzenes identification being formed in the model reaction of ribose with lysine. Aqueous solutions of ribose and lysine (at concentration of 0.1 mol/dm3 each) were mixed in equal volumes 10 cm3 + 10 cm3. The pH of the mixtures were adjusted to 5.6 using citrate-phosphorous buffer. In that way conditions simulating pH of meat were obtained. The mixtures were heated inside the gastronomic roaster during 0, 5, 10, 15, 30, 45 and 60 minutes respectively, at the temperature 185 +/- 5 degrees C. After reactions, in the mixtures, the profiles of volatile compounds, including alkylbenzenes, were analyzed by GC-MS method. The compounds were being identified by: comparing each mass spectrum (MS) with spectra from the known libraries of MS; calculating the linear retention indexes (LRI); seeking similar LRI values of analogue compounds in literature. Amounts of volatiles were calculated in relation to amount of internal standard (IS) [-], dividing the area of the compound by area of IS. The kinds and amounts of alkylbenzenes depended on the duration of the reaction time. Maximally 16 various alkylbenzenes were developed. More of these compounds could be identified with the probability of 85-90%, using only MS, because of the lack information in literature. Moreover, the multi-dimensional GCxGC-MS or other chromatographic methods in order to make these compounds being better explored seems to be advisable. The identification of the compounds being formed during broiling of meat is very important, because of the fact that many of arising substances are considered to be unhealthy and undesirable food contaminants. Thus these compounds should be routinely investigated in food products.

Super-enhanced particle nucleation in styrene emulsion polymerization in the presence of sodium styrene sulfonate.

PubMed

Farias-Cepeda, Lorena; Herrera-Ordonez, Jorge; Hernandez-Martinez, Angel R; Estevez, Miriam; Rosales-Marines, Lucero

2017-08-15

The styrene (St) emulsion polymerization using Aerosol MA80 as surfactant and in the presence of sodium styrene sulfonate (NaSS) was studied. The effect of NaSS content was assessed using MA80 concentrations below and at the critical micellar concentration. It was found that at the higher NaSS and MA80 contents, the number of particles (N) reaches a maximum of the order of 10 17 particles/cm 3 water, a huge value that has never been reported. In this work an explanation for this super-enhanced particle nucleation phenomenon is proposed. Such hypothesis is based on the role of St-NaSS oligomers formed in the aqueous phase and their synergy with MA80 molecules to provide colloidal stability to the system. The proposal seems to be consistent with the experimental data obtained for the evolution of monomer conversion, N, particles size distribution and the wideness of this latter as well as with a theoretical estimation of the N. Copyright © 2017 Elsevier Inc. All rights reserved.

Spectrofluorimetric study on the inclusion interaction between vitamin K 3 with p-( p-sulfonated benzeneazo)calix[6]arene and determination of VK 3

NASA Astrophysics Data System (ADS)

Zhou, Yunyou; Xu, Hongwei; Wu, Lian; Liu, Chun; Lu, Qin; Wang, Lun

2008-11-01

The characteristics of host-guest complexation between p-( p-sulfonated benzeneazo) calix[6]arene (SBC6A) and vitamin K 3 (VK 3) were investigated by fluorescence spectrometry. A 1:1 stoichiometry for the complexation was established and was verified by Job's plot. An association constant of 4.95 × 10 3 L mol -1 at 20 °C was calculated by applying a deduced equation. The interaction mechanism of the inclusion complex was discussed. It was found that the fluorescence of SBC6A could be remarkably quenched by an appropriate amount of VK 3 especially when non-ionic surfactant Triton X-100 existed. According to the obtained results, a novel sensitive spectrofluorimetric method for the determination of VK 3 based on supramolecular complex was developed with a linear range of 5.0 × 10 -7-3.0 × 10 -5 mol L -1 and a detection limit of 2.0 × 10 -7 mol L -1. The proposed method was used to determine VK 3 in commercial preparations with satisfactory results.

Spectrofluorimetric study on the inclusion interaction between vitamin K3 with p-(p-sulfonated benzeneazo)calix[6]arene and determination of VK3.

PubMed

Zhou, Yunyou; Xu, Hongwei; Wu, Lian; Liu, Chun; Lu, Qin; Wang, Lun

2008-11-15

The characteristics of host-guest complexation between p-(p-sulfonated benzeneazo) calix[6]arene (SBC6A) and vitamin K3 (VK3) were investigated by fluorescence spectrometry. A 1:1 stoichiometry for the complexation was established and was verified by Job's plot. An association constant of 4.95 x 10(3)L mol(-1) at 20 degrees C was calculated by applying a deduced equation. The interaction mechanism of the inclusion complex was discussed. It was found that the fluorescence of SBC6A could be remarkably quenched by an appropriate amount of VK3 especially when non-ionic surfactant Triton X-100 existed. According to the obtained results, a novel sensitive spectrofluorimetric method for the determination of VK3 based on supramolecular complex was developed with a linear range of 5.0 x 10(-7) -3.0 x 10(-5)mol L(-1) and a detection limit of 2.0 x 10(-7)mol L(-1). The proposed method was used to determine VK3 in commercial preparations with satisfactory results.

Sulfonated macro-RAFT agents for the surfactant-free synthesis of cerium oxide-based hybrid latexes.

PubMed

Garnier, Jérôme; Warnant, Jérôme; Lacroix-Desmazes, Patrick; Dufils, Pierre-Emmanuel; Vinas, Jérôme; van Herk, Alex

2013-10-01

Three types of amphiphatic macro-RAFT agents were employed as compatibilizers to promote the polymerization reaction at the surface of nanoceria for the synthesis of CeO2-based hybrid latexes. Macro-RAFT copolymers and terpolymers were first synthesized employing various combinations of butyl acrylate as a hydrophobic monomer and acrylic acid (AA) and/or 2-acrylamido-2-methylpropane sulfonic acid (AMPS) as hydrophilic monomers. After characterizing the adsorption of these macro-RAFT agents at the cerium oxide surface by UV-visible spectrometry, emulsion copolymerization reactions of styrene and methyl acrylate were then carried out in the presence of the surface-modified nanoceria. Dynamic Light Scattering and cryo-Transmission Electron Microscopy were employed to confirm the hybrid structure of the final CeO2/polymer latexes, and proved that the presence of acrylic acid units in amphiphatic macro-RAFT agents enabled an efficient formation of hybrid structures, while the presence of AMPS units, when combined with AA units, resulted in a better distribution of cerium oxide nanoclusters between latex particles. Copyright © 2013 Elsevier Inc. All rights reserved.

Evaluation of ultraviolet spectrophotometry for simultaneous analysis of alkylbenzenes, alkylnaphthalenes, alkylanthracenes/phenanthrenes and total aromatics in mid-distillate fuels

NASA Technical Reports Server (NTRS)

Kim, W. S.; Seng, G. T.

1982-01-01

A rapid ultraviolet spectrophotometric method for the simultaneous determination of aromatics in middistillate fuels was developed and evaluated. In this method, alkylbenzenes, alkylnaphthalenes, alkylanthracenes/phenanthracenes and total aromatics were determined from ultraviolet spectra of the fuels. The accuracy and precision were determined using simulated standard fuels with known compositions. The total aromatics fraction accuracy was 5% for a Jet A type fuel and 0.6% for a broadened properties jet turbine type fuel. Precision, expressed as relative standard deviations, ranged from 2.9% for the alkylanthracenes/phenanthrenes to 15.3% for the alkylbenzenes. The accuracy, however, was less for actual fuel samples when compared to the results obtained by a mass spectrometric method. In addition, the ASTM D-1840 method for naphthalenes by ultraviolet spectroscopy was evaluated.

Investigation on structural, optical and electrical properties of polythiophene-Al2O3 composites

NASA Astrophysics Data System (ADS)

Vijeth, H.; Yesappa, L.; Niranjana, M.; Ashokkumar, S. P.; Devendrappa, H.

2018-05-01

The polythiophene (PTH) and polythiophene-Al2O3 composites prepared by in situ chemical polymerisation in the presence of anionic surfactant camphor sulfonic acid (CSA). The formation of composite is confirmed by X-ray Diffraction (XRD) and Energy Dispersive X-ray spectroscopy (EDX) analysis. The surface morphology was studied using Field Emission Electron Microscopy (FESEM). Optical properties was studied using UV-visible spectroscopy, it observed decrease in the band gap reveals material has potential application in optical devices. The dielectric constant and AC conductivity of composite have been studied for different temperature in the frequency range 1 kHz -1 MHz.

Evaluation of proposed Skylab and SSP soap products.

NASA Technical Reports Server (NTRS)

Durfee, R. L.; Spurlock, J. M.; Whitmore, F. C.

1973-01-01

Four candidate cleansing agents evaluated in terms of potential hazards to crew members included two soaps (Neutrogena bar soap and Olive Leaf Liquid), one nonfoaming surfactant (Miranol JEM), and one laundry detergent (sodium dodecylbenzene sulfonate). None of the four exhibited adverse dermatological effects from skin patch tests or supported growth of potentially pathogenic microorganisms. Aqueous solutions of Neutrogena did support a mold species. Neutrogena and Miranol JEM were used in a simulated Skylab personal hygiene regimen with no adverse effects on skin or skin microflora. Based on our results, each of these agents appear to be a promising candidate material for the use intended.

Simultaneous gas chromatographic-mass spectrometric quantitation of the alkylbenzene inert components, pesticide manufacturing by-products and active ingredient in two malathion formulations.

PubMed

Lin, Y W; Hee, S S

1998-07-24

A rapid, reliable and effective method for direct determination of the inert components, manufacturing by-products of the pesticide, and active ingredient in two malathion formulations has been established using capillary gas chromatography-mass spectrometry (GC-MS) with the internal standard method. The C2-, C3-, and C4-alkylbenzenes, the major pesticide manufacturing by-products (O,O,S-trimethylthionophosphate, diethyl maleate and O,O,O-trimethylthionophosphate), and malathion were resolved, and quantified in the same chromatogram. Structural identification was based on MS total ion current data, comparison of GC retention times with those of authentic standards, and retention indices. O,O,S-Trimethylthionophosphate was quantified at 3.57 +/- 0.31% (w/w) in one malathion formulation. While the malathion contents were within specifications for both formulations, the total alkylbenzene contents were not.

Applications of micellar enzymology to clean coal technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Walsh, C.T.

1990-10-26

This project is designed to develop methods for pre-combustion coal remediation by implementing recent advances in enzyme biochemistry. The novel approach of this study is incorporation of hydrophilic oxidative enzymes in reverse micelles in an organic solvent. Enzymes from commercial sources or microbial extracts are being investigated for their capacity to remove organic sulfur from coal by oxidation of the sulfur groups, splitting of C-S bonds and loss of sulfur as sulfuric acid Dibenzothiophene (DBT) and ethlyphenylsulfide (EPS) are serving as models of organic sulfur-containing components of coal in initial studies. A goal of this project is to define amore » reverse micelle system that optimizes the catalytic activity of enzymes toward desulfurization of model compounds and ultimately coal samples. Among the variables which will be examined are the surfactant, the solvent, the water:surfactant ration and the pH and ionic strength of the aqueous phase. Studies were carried out with HRP, Type I RZ=1.2 and Type VI RZ=3.2 and laccase from Polyporus versicolor. Substrates for HRP assays included hydrogen peroxide, DBT, DBT sulfoxide, and DBT sulfone. Buffers included sodium phosphate. For formation of reverse micelle solutions the surfactant AOT, di(2-ethyl-hexyl)sodium sulphosuccinate, was obtained from Sigma Chemical Co. Isooctant was used as organic solvent. 12 refs., 5 figs., 3 tabs.« less

Treatment of greywater by forward osmosis technology: role of the operating temperature.

PubMed

Wang, Ce; Li, Yongmei; Wang, Yanqiang

2018-06-04

Effects of operating conditions were investigated in terms of water flux, reverse salt flux (RSF) and pollutant rejection in a forward osmosis (FO) membrane system treating synthetic greywater. Changing cross-flow velocity had a slight impact on the performance of the FO membrane. Elevating operating temperature was more effective than increasing draw solution concentration to enhance the water flux. Further observation on the effect of heating mode showed that when the temperature was increased from 20 to 30°C, heating the feed solution (FS) side was better than heating the draw solution (DS) side or heating both sides; further increasing the temperature to 40 and 50°C, heating both the FS and DS achieved much higher water flux compared with only increasing the FS or DS temperature. Under isothermal conditions, a higher water flux and a lower RSF were achieved at 40°C than at other temperatures. Changing either FS or DS temperature had similar influences on water flux and RSF. The FO process revealed high rejection of nitrate (95.7%-100%), ammonia nitrogen (98.8%-100%), total nitrogen (97.4%-99.9%), linear alkylbenzene sulfonate (100%) and Mg (97.5%-100%). A mathematical model that could well simulate the water flux evolution in the present FO system was recommended.

Quantifying structural modifications of gills of two fish species Astyanax altiparanae (Lambari) and Prochilodus lineatus (Curimbatá) after exposure to biodegradable detergents in urban lake water.

PubMed

Fiorelini Pereira, Bruno; Alves, Anderson Luis; Senhorini, José Augusto; Hakime Scalize, Priscilla; Tocchini De Figueiredo, Fellipe Augusto; Pitol, Dimítrius Leonardo; Caetano, Flávio Henrique

2017-01-01

Anthropic actions in rivers and urban lakes are a cause for concern to our ecosystem. The effects on fauna and flora of substances discharged into waterways have become a focus for investigations globally. Biodegradable detergents are widely used in residences and small industries, but little is known regarding the consequences on fish fauna. The objective of the present study was to identify modifications in gill structure in two fish species, Astyanax altiparanae and Prochilodus lineatus, after treatment with water obtained from an urban lake and an exposure to 1 ppm diluted biodegradable detergents (linear alkylbenzene sulfonate). Data demonstrated exposure to urban lake produced various alterations in gill functions such as lamellar fusions, aneurysms, mucous, and chlorine cell proliferation, which may be attributed to the presence of detergents in the water but may also be a consequence of synergetic actions of detergents with other pollutants. Results showed that the levels of NO - 2 , Na, F - , Cl - , and Fe were significantly higher in urban lake water but in the presence of detergents Ni was also detected. Evidence indicates that biodegradable detergents produce damage to gill functions, which subsequently alters the fish physiology and reduces the ability to cope with stress and survival.

Molecular Rotors for Universal Quantitation of Nanoscale Hydrophobic Interfaces in Microplate Format.

PubMed

Bisso, Paul W; Tai, Michelle; Katepalli, Hari; Bertrand, Nicolas; Blankschtein, Daniel; Langer, Robert

2018-01-10

Hydrophobic self-assembly pairs diverse chemical precursors and simple formulation processes to access a vast array of functional colloids. Exploration of this design space, however, is stymied by lack of broadly general, high-throughput colloid characterization tools. Here, we show that a narrow structural subset of fluorescent, zwitterionic molecular rotors, dialkylaminostilbazolium sulfonates [DASS] with intermediate-length alkyl tails, fills this major analytical void by quantitatively sensing hydrophobic interfaces in microplate format. DASS dyes supersede existing interfacial probes by avoiding off-target fluorogenic interactions and dye aggregation while preserving hydrophobic partitioning strength. To illustrate the generality of this approach, we demonstrate (i) a microplate-based technique for measuring mass concentration of small (20-200 nm), dilute (submicrogram sensitivity) drug delivery nanoparticles; (ii) elimination of particle size, surfactant chemistry, and throughput constraints on quantifying the complex surfactant/metal oxide adsorption isotherms critical for environmental remediation and enhanced oil recovery; and (iii) more reliable self-assembly onset quantitation for chemically and structurally distinct amphiphiles. These methods could streamline the development of nanotechnologies for a broad range of applications.

The preparation of neem oil microemulsion (Azadirachta indica) and the comparison of acaricidal time between neem oil microemulsion and other formulations in vitro.

PubMed

Xu, Jiao; Fan, Qiao-Jia; Yin, Zhong-Qiong; Li, Xu-Ting; Du, Yong-Hua; Jia, Ren-Yong; Wang, Kai-Yu; Lv, Cheng; Ye, Gang; Geng, Yi; Su, Gang; Zhao, Ling; Hu, Ting-Xiu; Shi, Fei; Zhang, Li; Wu, Chang-Long; Tao, Cui; Zhang, Ya-Xue; Shi, Dong-Xia

2010-05-11

The preparation of neem oil microemulsion and its acaricidal activity in vitro was developed in this study. In these systems, the mixture of Tween-80 and the sodium dodecyl benzene sulfonate (SDBS) (4:1, by weight) was used as compound surfactant; the mixture of compound surfactant and hexyl alcohol (4:1, by weight) was used as emulsifier system; the mixture of neem oil, emulsifier system and water (1:3.5:5.5, by weight) was used as neem oil microemulsion. All the mixtures were stired in 800 rpm for 15 min at 40 degrees C. The acaricidal activity was measured by the speed of kill. The whole lethal time value of 10% neem oil microemulsion was 192.50 min against Sarcoptes scabiei var. cuniculi larvae in vitro. The median lethal time value was 81.7463 min with the toxicity regression equations of Y=-6.0269+3.1514X. These results demonstrated that neem oil microemulsion was effective against Sarcoptes scabie var. cuniculi larvae in vitro. (c) 2010. Published by Elsevier B.V. All rights reserved.

Medium effects on fluorescence of ciprofloxacin hydrochloride

NASA Astrophysics Data System (ADS)

Yang, Rui; Fu, Yan; Li, Long-Di; Liu, Jia-Ming

2003-10-01

The medium (pH, organic solvents, cyclodextrin (CD) or surfactants) effects on the fluorescence of ciprofloxacin hydrochloride (CPFX·HCl) were studied in detail. It is found that the three acid constants of ciprofloxacin (CPFX) are near to each other. Therefore the relation curve between pH and fluorescence intensity has no strident change and keeps relative stable in the pH range of 2-7. When pH was in the range of 5.5-6.0, the fluorescence intensity of CPFX reached the max. The kind and amount of organic solvent added to the luminescent system have various effects. Ethanol quenched fluorescence and the fluorescence excitation wavelength is red shift at first and then blue shift. Acetone has complicated effects on the fluorescence properties of CPFX·HCl solution. The experiment result shows that acetone is really a quencher when its volume content in the system is from 0 to 20%, but when its content is 90%, the signal intensity is unexpectedly one and a half times as much as that of no acetone. This means that there is a strong interaction between the acetone and CPFX; CPFX·H + could be included into the γ-CD but the capping effect is not notable. The effect of cationic surfactant cetyltrimethylammonium bromide and non-ionic surfactant TX-100 and TX-80 on CPFX fluorescence was unimpressive, but the anionic surfactant's effect is aberrant. The fluorescence intensity of CPFX·HCl solution experiences three stages of increasing, decreasing and increasing in turn, as sodium dodecyl sulfate is adding gradually. But for sodium lauryl sulfonate, there are only two stages of decreasing and increasing with the concentration increasing. It is problematic to illustrate clearly the effect mechanism of acetone and anionic surfactant at present. Undoubtedly, the experimental results in this paper should be useful in practice works and the research is worth studying still further.

Enhancement in Elastic Bending Rigidity of Polymer Loaded Reverse Microemulsions.

PubMed

Geethu, P M; Yadav, Indresh; Aswal, Vinod K; Satapathy, Dillip K

2017-11-14

Elastic bending rigidity of the surfactant shell is a crucial parameter which determines the phase behavior and stability of microemulsion droplets. For water-in-oil reverse microemulsions stabilized by AOT (sodium 1,4-bis(2-ethylhexoxy)-1,4-dioxobutane-2-sulfonate) surfactant, the elastic bending rigidity is close to thermal energy at room temperature (k B T) and can be modified by the presence of hydrophilic polymers. Here, we explore the influence of two polymers polyethylene glycol (PEG) and polyvinylpyrrolidone (PVP), both having nearly same size (radius of gyration, R g ) but different dipole moment, on elastic bending rigidity of water-AOT-n-decane reverse microemulsions via estimating the percolation temperatures (T P ) and droplet radii using dielectric relaxation spectroscopy (DRS) and small-angle neutron scattering (SANS) techniques. Notably, an increase in T P is observed on introducing PEG and PVP polymers and is attributed to the adsorption of polymer chains onto the surfactant monolayer. The stability of the droplet phase of microemulsion after the incorporation of PEG and PVP polymers is confirmed by contrast matching SANS experiments. An enhancement in elastic bending rigidity of AOT surfactant shell amounting to ∼46% is observed upon incorporation of PVP into the droplet core, whereas for PEG addition, a smaller increase of about 17% is recorded. We conjecture that the considerable increase in elastic bending rigidity of the surfactant monolayer upon introducing PVP is because of the strong ion-dipole interaction between anionic AOT and dipoles present along the PVP polymer chains. Scaling exponents extracted from the temperature dependent electrical conductivity measurements and the frequency dependent scaling of conductivity at percolation indicate the dynamic nature of percolation for both pure and polymer loaded reverse microemulsions. The decrease in activation energy of percolation upon incorporating PEG and PVP polymer molecules also reflects the increased stability of microemulsion droplets against thermal fluctuations.

In vitro analysis of the effect of alkyl-chain length of anionic surfactants on the skin by using a reconstructed human epidermal model.

PubMed

Yamaguchi, Fumiko; Watanabe, Shin-Ichi; Harada, Fusae; Miyake, Miyuki; Yoshida, Masaki; Okano, Tomomichi

2014-01-01

We investigated the effect of the alkyl-chain length of anionic surfactants on the skin using an in vitro model. The evaluated anionic surfactants were sodium alkyl sulfate (AS) and sodium fatty acid methyl ester sulfonate (MES), which had different alkyl-chain lengths (C8-C14). Skin tissue damage and permeability were examined using a reconstructed human epidermal model, LabCyte EPI-MODEL24. Skin tissue damage was examined by measuring cytotoxicity with an MTT assay. Liquid chromatography/tandem mass spectrometry (LC/MS-MS) and liquid chromatography/mass spectrometry (LC/MS) were used to detect surfactants that permeated into the assay medium through an epidermal model. To assess the permeation mechanism and cell damage caused by the surfactants through the epidermis, we evaluated the structural changes of Bovine Serum Albumin (BSA), used as a simple model protein, and the fluidity of 1,2-dipalmitoyl-sn-glycero-3-phosphpcholine (DPPC) liposome, which serves as one of the most abundant phospholipid models of living cell membranes in the epidermis. The effects of the surfactants on the proteins were measured using Circular Dichroism (CD) spectroscopy, while the effects on membrane fluidity were investigated by electron spin resonance (ESR) spectroscopy. ET50 (the 50% median effective time) increased as follows: C10 < C12 < C8 < C14 in AS and C8, C10 < C12 < C14 in MES. The order of permeation through the LabCyte EPI-MODEL24 was C10 > C12 > C14, for both AS and MES. For both AS and MES, the order parameter, which is the criteria for the microscopic viscosity of lipid bilayers, increased as follows: C10 < C12 < C14, which means the membrane fluidity is C10 > C12 > C14. It was determined that the difference in skin tissue damage in the LabCyte EPI-MODEL24 with C10 to C14 AS and MES was caused by the difference in permeation and cell membrane fluidity through the lipid bilayer path in the epidermis.

Chemically modified carbon paste and membrane sensors for the determination of benzethonium chloride and some anionic surfactants (SLES, SDS, and LABSA): Characterization using SEM and AFM.

PubMed

Issa, Yousry M; Mohamed, Sabrein H; Baset, Mohamed Abd-El

2016-08-01

Chemically modified carbon-paste (CMCP) and membrane- sensors based on incorporating benzothonium-tetraphenylborate (BT-TPB) were constructed for the analysis of benzethonium chloride, and some other surfactants such as sodium lauryl ether sulphate (SLES), sodium dodecyl sulphate (SDS), and linear alkylbenzene sulphonic acid (LABSA). All sensors showed good sensitivity and reverse wide linearity over a concentration range of 5.97×10(-7) to 1.00×10(-3) and 5.96×10(-7) to 3.03×10(-3)molL(-1) with limit of detection of 3.92×10(-7)and 3.40×10(-7)molL(-1) for membrane and chemically modified carbon paste sensors, respectively, with respect to benzethonium chloride (BT.Cl). They could be used over a wide pH range of 2.0-10.0. The thermal coefficients of membrane and CMCP sensors are 5.40×10(-4), 1.17×10(-4)V/°C, respectively. The sensors indicated a wide selectivity over different inorganic cations. The effect of soaking on the surface morphology of the membrane sensor was studied using EDX-SEM and AFM techniques. The response time was <10s The freshly prepared, exhausted membrane, and CMCP sensors were successfully applied for the potentiometric determination of the pure BT.Cl solution. They were also used for the determination of its pharmaceutical formulation Dermoplast(®) antibacterial spray (20% benzocaine+0.2% benzethonium chloride) with recovery values ranging from 97.54±1.70 to 101.25±1.12 and from 96.32±2.49 to 101.23±2.15%. The second goal of these sensors is the potentiometric determination of different surfactants such as SLES, SDS, and LABSA with good recovery values using BT.Cl as a titrant in their pure forms, and in samples containing one of them (shampoo, Touri(®) dishwashing liquid, and waste water). The statistical analysis of the obtained data was studied. Copyright © 2016 Elsevier B.V. All rights reserved.

Effect of Protein Incorporation on the Nanostructure of the Bicontinuous Microemulsion Phase of Winsor-III Systems: A Small-Angle Neutron Scattering Study

DOE PAGES

Hayes, Douglas G.; Gomez del Rio, Javier A.; Ye, Ran; ...

2015-01-20

Small-angle neutron scattering (SANS) analysis using the Teubner₋Strey model has been employed to evaluate the effect of protein incorporation into the middle, bicontinuous microemulsion (BμE) phase of Winsor-III (W III) systems formed by an aerosol-OT (AOT)/alkyl ethoxylate mixed surfactant system to understand better the extraction of proteins into and out of BμEs and to study the effect of proteins on a system that serves as a biomimetic analog of cell membranes. Under conditions of high salinity, the incorporation of positively charged proteins cytochrome c, lysozyme, and α-chymotrypsin, near their solubilization limit in the BμEs promoted the release of water andmore » oil from the BμEs, a decrease in the quasi-periodic repeat distance (d), an increase in ordering (a decrease in the amphiphilicity factor, f a) for the surfactant monolayers, and a decrease in the surface area per surfactant headgroup, suggesting that the proteins affected the self-assembly of components in the BμE phase and produced Debye shielding of AOTs sulfonate headgroup. For W III systems possessing lower salinity, cytochrome c reduced the efficiency of surfactant in the BμE phase, noted by increases in d and f a, suggesting that the enzyme and AOT underwent ion pairing. We find that the results of this study demonstrate the importance of ionic strength to modulate proteinsurfactant interactions, which in turn will control the release of proteins encapsulated in the BμEs, relevant to W III-based protein extraction and controlled release from BμE delivery systems, and demonstrate the utility of BμEs as a model system to understand the effect of proteins on biomembranes.« less

Improved photostability of hydrophobic natural dye incorporated in organo-modified hydrotalcite

NASA Astrophysics Data System (ADS)

Kohno, Yoshiumi; Asai, Saeko; Shibata, Masashi; Fukuhara, Choji; Maeda, Yasuhisa; Tomita, Yasumasa; Kobayashi, Kenkichiro

2014-08-01

β-carotene and annatto extract are typical carotenoids used as safe colorants for foods. However, the instability against irradiation limits their wide use. The improvement of stability was investigated by the intercalation of dye into the interlayer space of the anion-exchangeable clay, hydrotalcite. A hydrophobic environment was constructed in the interlayer space of the hydrotalcite by its modification with anionic surfactants (dodecyl sulfate and dodecylbenzene sulfonate). The lipophilic β-carotene and annatto dye were successfully incorporated into the organo-modified hydrotalcite, and the incorporated dyes exhibited improved photostability under visible irradiation from a 100 W halogen lamp (190 klux) in the air. The effect of the stabilization on the anionic annatto dye was higher by the incorporation in the modified hydrotalcite than that in the modified cation exchangeable clay, suggesting that the polarity of the clay sheet had some influence on the stabilization of the incorporated dye. The stabilization effect of β-carotene was not so significant as that of the annatto dye, because sufficient intercalation of non-polar β-carotene might require stronger hydrophobic environment. The π-π interaction between the β-carotene and the benzene ring of dodecylbenzene sulfonate was found to contribute to the stability enhancement.

Determination of caffeic acid in wine using PEDOT film modified electrode.

PubMed

Bianchini, C; Curulli, A; Pasquali, M; Zane, D

2014-08-01

A novel method using PEDOT (poly(3,4-ethylenedioxy) thiophene) modified electrode was developed for the determination of caffeic acid (CA) in wine. Cyclic voltammetry (CV) with the additions standard method was used to quantify the analyte at PEDOT modified electrodes. PEDOT films were electrodeposited on Platinum electrode (Pt) in aqueous medium by galvanostatic method using sodium poly(styrene-4-sulfonate) (PSS) as electrolyte and surfactant. CV allows detecting the analyte over a wide concentration range (10.0nmoll(-1)-6.5mmoll(-1)). The electrochemical method proposed showed good statistical and analytical parameters as linearity range, LOD, LOQ and sensitivity. Copyright © 2014 Elsevier Ltd. All rights reserved.

Chemicals for enhanced oil recovery. Quarterly report, October 1-December 31, 1980

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, J.S. Jr.

1980-10-01

Studies on the salinity range in which three liquid phases are observed for systems containing a tall oil ethoxylate or related nonionic surfactant, a cosurfactant, aqueous NaCl, and a hydrocarbon were extended. Increasing hydrophile-lipophile balance, HLB, causes an increase in the salinity needed to effect the transition of the surfactant from the lower to the upper phase. However, other factors besides HLB seem to be involved. Addition of the nonionic surfactant increases optimal salinity by an amount which depends on its hydrophilic character. Sodium-2-methyloleate,-2-butyloleate, -2-hexyloleate, -2,2-dimethyloleate, and -2,2-diethyloleate were synthesized and its phase behavior in aqueous/hydrocarbon systems studied. Adsorption ofmore » a commercial petroleum sulfonate from 0.1 M NaCl on the sodium form of montmorillonite was reduced a factor of ten by caustic extract from bleaching of wood pulp. In a comparison of several pulping wastes or byproducts as sacrificial agents, caustic extract and weak black liquor appeared most effective, and lignosulfonate only slightly less effective. Plugging tests of the filtrates obtained in the biomass-polymer separations indicated that polish filtration probably would be required. The microscreen is the most economical of the biomass separation methods. Small fermenter tests indicate that Sclerotium rolfsii cultures are able to tolerate salinity of 2 to 4% w/v NaCl in the fermentation broth makeup water; however, the organism was unable to grow in 6% w/v NaCl.« less

Degradation of soil-sorbed trichloroethylene by stabilized zero valent iron nanoparticles: Effects of sorption, surfactants, and natural organic matter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Man; He, Feng; Zhao, Dongye

2011-01-01

Zero valent iron (ZVI) nanoparticles have been studied extensively for degradation of chlorinated solvents in the aqueous phase, and have been tested for in-situ remediation of contaminated soil and groundwater. However, little is known about its effectiveness for degrading soil-sorbed contaminants. This work studied reductive dechlorination of trichloroethylene (TCE) sorbed in two model soils (a potting soil and Smith Farm soil) using carboxymethyl cellulose (CMC) stabilized Fe-Pd bimetallic nanoparticles. Effects of sorption, surfactants and dissolved organic matter (DOC) were determined through batch kinetic experiments. While the nanoparticles can effectively degrade soil-sorbed TCE, the TCE degradation rate was strongly limited bymore » desorption kinetics, especially for the potting soil which has a higher organic matter content of 8.2%. Under otherwise identical conditions, {approx}44% of TCE sorbed in the potting soil was degraded in 30 h, compared to {approx}82% for Smith Farm soil (organic matter content = 0.7%). DOC from the potting soil was found to inhibit TCE degradation. The presence of the extracted SOM at 40 ppm and 350 ppm as TOC reduced the degradation rate by 34% and 67%, respectively. Four prototype surfactants were tested for their effects on TCE desorption and degradation rates, including two anionic surfactants known as SDS (sodium dodecyl sulfate) and SDBS (sodium dodecyl benzene sulfonate), a cationic surfactant hexadecyltrimethylammonium (HDTMA) bromide, and a non-ionic surfactant Tween 80. All four surfactants were observed to enhance TCE desorption at concentrations below or above the critical micelle concentration (cmc), with the anionic surfactant SDS being most effective. Based on the pseudo-first-order reaction rate law, the presence of 1 x cmc SDS increased the reaction rate by a factor of 2.5 when the nanoparticles were used for degrading TCE in a water solution. SDS was effective for enhancing degradation of TCE sorbed in Smith Farm soil, the presence of SDS at sub-cmc increased TCE degraded by {approx}10%. However, effect of SDS on degradation of TCE in the potting soil was more complex. The presence of SDS at sub-cmc decreased TCE degradation by 5%, but increased degradation by 5% when SDS dosage was raised to 5 x cmc. The opposing effects were attributed to combined effects of SDS on TCE desorption and degradation, release of soil organic matter and nanoparticle aggregation. The findings strongly suggest that effect of soil sorption on the effectiveness of Fe-Pd nanoparticles must be taken into account in process design, and soil organic content plays an important role in the overall degradation rate and in the effectiveness of surfactant uses.« less

Interfacial concentrations of chloride and bromide in zwitterionic micelles with opposite dipoles: experimental determination by chemical trapping and a theoretical description.

PubMed

de Souza, Tereza Pereira; Chaimovich, Hernan; Fahr, Alfred; Schweitzer, Bianca; Agostinho Neto, Augusto; Cuccovia, Iolanda Midea

2012-04-01

Interfacial concentrations of chloride and bromide ions, with Li(+), Na(+), K(+), Rb(+), Cs(+), trimethylammonium (TMA(+)), Ca(2+), and Mg(2+) as counterions, were determined by chemical trapping in micelles formed by two zwitterionic surfactants, namely N-hexadecyl-N,N-dimethyl-3-ammonio-1-propanesulfonate (HPS) and hexadecylphosphorylcholine (HDPC) micelles. Appropriate standard curves for the chemical trapping method were obtained by measuring the product yields of chloride and bromide salts with 2,4,6-trimethyl-benzenediazonium (BF(4)) in the presence of low molecular analogs (N,N,N-trimethyl-propane sulfonate and methyl-phosphorylcholine) of the employed surfactants. The experimentally determined values for the local Br(-) (Cl(-)) concentrations were modeled by fully integrated non-linear Poisson Boltzmann equations. The best fits to all experimental data were obtained by considering that ions at the interface are not fixed at an adsorption site but are free to move in the interfacial plane. In addition, the calculation of ion distribution allowed the estimation of the degree of ion coverage by using standard chemical potential differences accounting for ion specificity. Copyright © 2012 Elsevier Inc. All rights reserved.

Transport and recovery of bacteriophage PRD1 in a sand and gravel aquifer: Effect of sewage-derived organic matter

USGS Publications Warehouse

Pieper, A.P.; Ryan, J.N.; Harvey, R.W.; Amy, G.L.; Illangasekare, T.H.; Metge, D.W.

1997-01-01

To test the effects of sewage-derived organic matter on virus attachment, 32P-labeled bacteriophage PRD1, linear alkylbenzene sulfonates (LAS), and tracers were injected into sewage-contaminated (suboxic, elevated organic matter) and uncontaminated (oxic, low organic matter) zones of an iron oxide-coated quartz sand and gravel aquifer on Cape Cod, MA. In the uncontaminated zone, 83% of the PRD1 were attenuated over the first meter of transport by attachment to aquifer grains. In the contaminated zone, 42% of the PRD1 were attenuated over the first meter of transport. Sewage-derived organic matter contributed to the difference in PRD1 attenuation by blocking attachment sites in the contaminated zone. At greater distances down gradient (to a total transport distance of 3.6 m), a near-constant amount of PRD1 continued to break through, suggesting that aquifer grain heterogeneities allowed a small amount of reversible attachment. Injection of an LAS mixture (25 mg L-1), a common sewage constituent, remobilized 87% of the attached PRD1 in the contaminated zone, but only 2.2% in the uncontaminated zone. LAS adsorption promoted virus recovery in the contaminated zone by altering the PRD1-surface interactions; however, the amount of LAS adsorbed was not sufficient to promote release of the attached PRD1 in the uncontaminated zone.

Field and laboratory investigations of inactivation of viruses (PRD1 and MS2) attached to iron oxide-coated quartz san

USGS Publications Warehouse

Ryan, Joseph N.; Harvey, Ronald W.; Metge, David W.; Elimelech, Menachem; Navigato, Theresa; Pieper, Ann P.

2002-01-01

Field and laboratory experiments were conducted to investigate inactivation of viruses attached to mineral surfaces. In a natural gradient transport field experiment, bacteriophage PRD1, radiolabeled with 32P, was injected into a ferric oxyhydroxide-coated sand aquifer with bromide and linear alkylbenzene sulfonates. In a zone of the aquifer contaminated by secondary sewage infiltration, small fractions of infective and 32P-labeled PRD1 broke through with the bromide tracer, followed by the slow release of 84% of the 32P activity and only 0.011% of the infective PRD1. In the laboratory experiments, the inactivation of PRD1, labeled with 35S (protein capsid), and MS2, dual radiolabeled with 35S (protein capsid) and 32P (nucleic acid), was monitored in the presence of groundwater and sediment from the contaminated zone of the field site. Release of infective viruses decreased at a much faster rate than release of the radiolabels, indicating that attached viruses were undergoing surface inactivation. Disparities between 32P and35S release suggest that the inactivated viruses were released in a disintegrated state. Comparison of estimated solution and surface inactivation rates indicates solution inactivation is ∼3 times as fast as surface inactivation. The actual rate of surface inactivation may be substantially underestimated owing to slow release of inactivated viruses.

Oligomers, organosulfates, and nitroxy organosulfates in rainwater identified by ultra-high resolution electrospray ionization FT-ICR mass spectrometry

NASA Astrophysics Data System (ADS)

Altieri, K. E.; Turpin, B. J.; Seitzinger, S. P.

2008-09-01

Wet deposition is an important removal mechanism for atmospheric organic matter, and a potentially important input for receiving ecosystems, yet less than 50% of rainwater organic matter is considered chemically characterized. Precipitation samples collected in New Jersey, USA, were analyzed by negative ion ultra-high resolution electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS). Elemental compositions of 552 unique molecular species were determined in the mass range 50 500 Da in the rainwater. Three main groups of organic compounds were identified: compounds containing carbon, hydrogen, and oxygen (CHO) only, sulfur (S) containing CHOS compounds, and S- and nitrogen containing CHONS compounds. Organic acids commonly identified in precipitation were detected, as well as linear alkylbenzene sulfonates, which are persistent pollutants commonly measured in river water, seawater, and sediments, but to our knowledge, not previously documented in atmospheric samples. Within the three main groups of compounds detected in the rainwater, oligomers, organosulfates, and nitroxy-organosulfates were identified. The majority of the compounds identified are products of atmospheric reactions and are known contributors to secondary organic aerosol (SOA) formed from gas phase, aerosol phase, and in-cloud reactions in the atmosphere. It is suggested that the large uncharacterized component of SOA is the main contributor to the large uncharacterized component of rainwater organic matter.

Pyrolytic indices of diagenetic transformation of lignin as biogeochemical proxies for soil organic matter quality and C storage potential

NASA Astrophysics Data System (ADS)

Jiménez-González, Marco A.; Almendros, Gonzalo; Álvarez, Ana M.; Jiménez-Morillo, Nicasio T.; González-Vila, Francisco J.

2017-04-01

The environmental factors involved in soil organic carbon sequestration remain unclear. The functional relationships between the macromolecular structure of the soil organic matter (SOM) and its resilience has been a constant in classical biogeochemical models. Other more recent hypotheses have postulated that preservation by soil minerals may play a chief role in the accumulation of stable SOM forms. However, additional experimental data are required to demonstrate a cause-to-effect relationship between preservation and stabilization. Some authors might consider that models neglecting the role of macromolecular structure are swapping cause and effect i.e., that SOM structurally flexible, weakly condensed and having 'open' structures is the one with high potential to interact with the soil mineral matrix, leading to stable microaggregates. In this study up to 35 topsoil samples (0-5 cm) were collected from different Spanish soils with contrasted values of organic C (the dependent variable), geological substrate and vegetation type. A wide array of uni- and multivariate chemometric models were applied to independent variables consisting of total abundances of the major aromatic compounds, i.e., alkylbenzenes and methoxyphenols released from whole soil samples using pyrolysis-gas chromatography-mass spectrometry (Py-GC/MS). These two families of compounds were selected since they are classically considered to inform on the degree of microbial reworking of lignins, which is an important precursor of the aromatic moiety of the SOM. A series of pyrolytic surrogate indices (aiming to express SOM diagenetic transformation in relation to the original biogenic molecular composition) were especially successful in forecasting SOC, viz: a) ratio between alkylbenzenes and methoxyphenols, b) ratio between short-chain (C0-C4) and long-chain (>C4) alkylbenzenes, c) ratio between methoxyphenols and short-chain alkylbenzenes, and d) ratios between methoxyphenols with different side-chain length, i.e., methyl-, ethyl-, vinyl-, propenyl- and aceto- derivatives of guaiacyl and syringyl rings. In particular partial least squares regression (PLS) models led to very significant prediction of SOC based exclusively on the major aromatic pyrolytic compounds as predictors, i.e, methoxyphenols and alkylbenzenes. The PLS coefficients showed high positive loadings for methoxyphenols (i.e., these compounds were diagnostic for soils with high C-storage potential), and negative for alkylbenzenes (which were characteristic for C-depleted soils). This may be explained as if selective preservation of lignin were the most efficient process in soils behaving as active C sinks. Conversely, the progressive smoothing in the lignin signature and the accumulation of methoxyl-lacking aromatics (i.e., short-chain alkylbenzenes) was typical in the soils with low SOC content but high levels of diagenetic alteration of lignin. The progressive alteration of C6-C3 phenylpropanoid lignin units also corresponded to the fact that heavily altered lignin, presumptively accumulated in SOM depleted soils, tended to release typical pyrolytic markers consisting of C0-C1 methoxyphenols instead of its vinyl and propenyl counterparts, in addition to major proportions of short-chain (

Determination of C6-C10 aromatic hydrocarbons in water by purge-and-trap capillary gas chromatography

USGS Publications Warehouse

Eganhouse, R.P.; Dorsey, T.F.; Phinney, C.S.; Westcott, A.M.

1993-01-01

A method is described for the determination of the C6-C10 aromatic hydrocarbons in water based on purge-and-trap capillary gas chromatography with flame ionization and mass spectrometric detection. Retention time data and 70 eV mass spectra were obtained for benzene and all 35 C7-C10 aromatic hydrocarbons. With optimized chromatographic conditions and mass spectrometric detection, benzene and 33 of the 35 alkylbenzenes can be identified and measured in a 45-min run. Use of a flame ionization detector permits the simultaneous determination of benzene and 26 alkylbenzenes.

Effect of hydro-oleophobic perfluorocarbon chain on interfacial behavior and mechanism of perfluorooctane sulfonate in oil-water mixture

PubMed Central

Meng, Pingping; Deng, Shubo; Du, Ziwen; Wang, Bin; Huang, Jun; Wang, Yujue; Yu, Gang; Xing, Baoshan

2017-01-01

Perfluorocarbon chain of perfluorooctane sulfonate (PFOS) is not only hydrophobic but also oleophobic, and its effect on PFOS distribution in oil-water mixture and underlying mechanism are unclear. For the first time, we propose that PFOS can emulsify oil-water mixture only in the presence of air, completely different from hydrocarbon surfactants. The perfluorocarbon chain repels hydrophobic compounds and its oleophobicity increases with decreasing polarity of organic solvents. The formed emulsion in oil phase contains high concentrations of PFOS, resulting in PFOS decrease in water. The increase of shaking speed and time as well as oil and air volume all increase the emulsification and decrease PFOS concentrations in water. During the settling process, the emulsion gradually disappears and the concentrated PFOS is released into water. The emulsification mechanism of PFOS based on air bubbles is proposed, and PFOS partitions to the interfaces of air bubbles with the hydro-oleophobic perfluorocarbon chain stretching into air bubbles and the polar head in water. This study clarifies the ambiguous understanding of the oleophobicity of perfluorocarbon chain in PFOS, and it is helpful for the understanding of the transport and fate of PFOS at oil-water interfaces in aquatic environments as well as the enhanced removal of PFOS from wastewater. PMID:28300199

Perfluoroctane sulfonate-induced changes in fetal rat liver ...

EPA Pesticide Factsheets

In utero exposure of rats to perfluorooctane sulfonate (PFOS, C8F17SO3), a widely disseminated product of the surfactant and coating industries, is associated with residual hepatoxic complications in the surviving offspring. This hepatocellular hypertrophy resembles that observed in adults and is characterized by peroxisome proliferation, lower serum cholesterol and fatty acid concentrations, and hypothyroxemia, most of which are suspected to be manifested through PPARalpha-mediated transcriptional regulation. The purpose of the present investigation was to develop a comprehensive characterization of the transcriptional changes associated with prenatal exposure to PFOS using global gene expression array analyses. Gravid Sprague-Dawley rats were administered 3 mg/kg PFOS by gavage daily from gestational day 2-20 and terminated on day 21. Although there was no treatment-related teratology, there was a substantial effect of PFOS on the perinatal hepatic transcriptome – 225 unique transcripts were identified as statistically increased and 220 decreased by PFOS exposure; few transcripts were changed by more than two-fold. Although the Ppara transcript itself was not affected, there was a significant increase in expression of gene transcripts associated with hepatic peroxisomal proliferation as well as those responsible for fatty acid activation, transport and oxidation (both mitochondrial and peoxisomal) pathways. Additional metabolic pathways altered by in ut

Effects of perfluorooctane sulfonate on genes controlling hepatic fatty acid metabolism in livers of chicken embryos.

PubMed

Jacobsen, Annette V; Nordén, Marcus; Engwall, Magnus; Scherbak, Nikolai

2018-06-02

Per- and polyfluoroalkyl substances (PFAS) are synthetic surfactants with a wide variety of applications; however, due to their stability, they are particularly resistant to degradation and, as such, are classed as persistent organic pollutants. Perfluorooctane sulfonate (PFOS) is one such PFAS that is still detectable in a range of different environmental settings, despite its use now being regulated in numerous countries. Elevated levels of PFOS have been detected in various avian species, and the impact of this on avian health is of interest when determining acceptable levels of PFOS in the environment. Due to its similarities to naturally occurring fatty acids, PFOS has potential to disrupt a range of biological pathways, particularly those associated with lipid metabolism, and this has been shown in various species. In this study, we have investigated how in ovo exposure to environmentally relevant levels of PFOS affects expression of genes involved in lipid metabolism of developing chicken embryos. We have found a broad suppression of transcription of genes involved in fatty acid oxidation and PPAR-mediated transcription with more significant effects apparent at lower doses of PFOS. These results highlight the need for more research investigating the biological impacts of low levels of PFAS to properly inform environmental policy governing their regulation.

Nature and chlorine reactivity of organic constituents from reclaimed water in groundwater, Los Angeles County, California

USGS Publications Warehouse

Leenheer, J.A.; Rostad, C.E.; Barber, L.B.; Schroeder, R.A.; Anders, R.; Davisson, M.L.

2001-01-01

The nature and chlorine reactivity of organic constituents in reclaimed water (tertiary-treated municipal wastewater) before, during, and after recharge into groundwater at the Montebello Forebay in Los Angeles County, CA, was the focus of this study. Dissolved organic matter (DOM) in reclaimed water from this site is primarily a mixture of aromatic sulfonates from anionic surfactant degradation, N-acetyl amino sugars and proteins from bacterial activity, and natural fulvic acid, whereas DOM from native groundwaters in the aquifer to which reclaimed water was recharged consists of natural fulvic acids. The hydrophilic neutral N-acetyl amino sugars that constitute 40% of the DOM in reclaimed water are removed during the first 3 m of vertical infiltration in the recharge basin. Groundwater age dating with 3H and 3He isotopes, and determinations of organic and inorganic C isotopes, enabled clear differentiation of recent recharged water from older native groundwater. Phenol structures in natural fulvic acids in DOM isolated from groundwater produced significant trihalomethanes (THM) and total organic halogen (TOX) yields upon chlorination, and these structures also were responsible for the enhanced SUVA and specific fluorescence characteristics relative to DOM in reclaimed water. Aromatic sulfonates and fulvic acids in reclaimed water DOM produced minimal THM and TOX yields.

A study of the antibacterial activity of L-phenylalanine and L-tyrosine esters in relation to their CMCs and their interactions with 1,2-dipalmitoyl-sn-glycero-3-phosphocholine, DPPC as model membrane.

PubMed

Joondan, Nausheen; Jhaumeer-Laulloo, Sabina; Caumul, Prakashanand

2014-01-01

Cationic amino acid-based surfactants are known to interact with the lipid bilayer of cell membranes resulting in depolarization, lysis and cell death through a disruption of the membrane topology. A range of cationic surfactant analogues derived from L-Phenylalanine (C1-C20) and L-Tyrosine (C8-C14) esters have been synthesized and screened for their antibacterial activity. The esters were more active against gram positive than gram negative bacteria. The activity increased with increasing chain length, exhibiting a cut-off effect at C12 for gram positive and C8/C10 for gram negative bacteria. The cut-off effect for gram negative bacteria was observed at a lower alkyl chain length. The CMC was correlated with the MIC, inferring that micellar activity contribute to the cut-off effect in antibacterial activity. The interaction of the cationic surfactants with the phospholipid vesicles (1,2-dipalmitoyl-sn-glycero-3-phosphocholine, DPPC) in the presence of 1-anilino-8-naphthalene sulfonate (ANS) and 1,6-diphenyl-1,3,5-hexatriene (DPH) as fluorescence probes showed that an increase in ionic interaction causes an increase in antibacterial activity. Increase in hydrophobic interaction increases the antibacterial activity only to a certain chain length, attributing to the cut-off effect. Therefore, both electrostatic and hydrophobic interactions, involving the polar and nonpolar moieties are of paramount importance for the bactericidal properties. Copyright © 2014 Elsevier GmbH. All rights reserved.

Study on Colloid Vibration Current in Aqueous Solution of Binary Surfactant Mixtures: Effects of Counterions and Hydrophobic Chains.

PubMed

Takata, Youichi; Hyono, Atsushi; Ohshima, Hiroyuki

2016-11-01

In order to elucidate an electroacoustic phenomenon of mixed micelles in an aqueous solution, we measured the colloid vibration current (CVI) in aqueous solutions of binary surfactant mixtures. Based on the thermodynamic treatment of critical micelle concentration (cmc) values determined by conductivity measurements, it was expected that dodecyltrimethylammonium bromide (DTAB) and dodecyltrimethylammonium chloride (DTAC) molecules would mix ideally in the micelle. However, the micelle composition as evaluated from the CVI measurement, based on the linear dependence of the CVI value on the micelle composition, differed from the aforementioned ideality. Considering these observations, we concluded that the CVI measurement was more sensitive to the counterion distribution near the micelle surface, whereas the thermodynamically determined micelle composition included the counterions more loosely bound in the diffuse double layer due to the electroneutrality condition included in its assumption. On the other hand, the phase diagram illustrating micelle formation in the lithium dodecyl sulfate (LiDS) - lithium perfluorooctane sulfonate (LiFOS) mixture system showed a heteroazeotropic point arising from the stronger interactions between homologous surfactants than between heterologous ones. Although the concentration dependence of CVI values was expected to drastically change at a heteroazeotropic point due to the enormous variation in the density of the micelle core, the results showed a monotonous change, which suggests that the density of the micelle core varies continuously. By taking the partial molar volume of fluorocarbon compounds in the hydrocarbon compounds into account, the density of the micelle core was affected by the size of the micelle as well as its constituents.

The behaviour of linear alkyl benzene sulphonate under direct discharge conditions in Vientiane, Lao PDR.

PubMed

Whelan, M J; Van Egmond, R; Guymer, I; Lacoursière, J O; Vought, L M B; Finnegan, C; Fox, K K; Sparham, C; O'Connor, S; Vaughan, M; Pearson, J M

2007-12-01

Direct discharge of untreated sewage to surface waters is a common practice in many parts of the world. However, relatively little is known about the behaviour of synthetic organic pollutants under these conditions. This paper describes a sampling campaign designed to track changes in water quality in a surface water system in Vientiane (Lao PDR) receiving significant quantities of untreated waste water. The study was based on following in-channel transport using a fluorescent tracer injected as a pulse, with a focus on the anionic surfactant linear alkylbenzene sulphonate (LAS) and ammonia. Water samples were collected at a number of stations with sampling times estimated to coincide with solute time-of-travel. The reduction in LAS concentration with flow-time could be approximated by first-order kinetics with a half life of about 7 h. Free ammonia concentrations decreased more slowly than LAS and remained above the level believed to be toxic for sensitive aquatic species along the entire channel. Changes in the ratios of LAS alkyl chain homologues to total LAS concentrations suggest a preferential removal of longer chain lengths. The role of biodegradation in the removal of LAS was confirmed by the presence of LAS metabolites (sulphophenylcarboxylates, SPCs) which increased systematically (as a fraction of LAS remaining) with flow-time.

Effect of H{sub 3}PW{sub 12}O{sub 40} impregnation on Sn-MCM-41 mesoporous molecular sieves and their physico-chemical properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nedumaran, D.; Department of Chemistry, RMK Engineering College, Chennai; Pandurangan, A., E-mail: pandurangan_a@yahoo.com

2015-01-15

Graphical abstract: The wide angle XRD shows the well dispersion of HPWA in Sn-MCM-41. It enhances the total acidity of the material. The acidity of the material is correlated with sulfone selectivity. The FT-IR of dibenzothiophene and product shows the formation of sulfone (DBTO{sub 2}). - Highlights: • To enhance the total acidity of Sn-MCM-41 TPA is impregnated. • FT-IR and {sup 31}P MAS NMR confirms the HPWA intact on Sn-MCM-41. • EDAX shows the presence of W and P on Sn-MCM-41. • In ODS formation of sulfone was confirmed by FT-IR and {sup 1}H NMR. • The order ofmore » the catalytic activity of the catalysts are 18HSnM > 28HSnM > 8HSnM. - Abstract: Si-Sn-MCM-41 (Si/Sn = 110) mesoporous molecular sieve was synthesized by hydrothermal sol–gel method using cetyltrimethylammonium bromide (CTAB) as surfactant and SnCl{sub 4}·5H{sub 2}O as a metal source. To generate surface acidity of Si-Sn-MCM-41, 12-tungstophosphoric acid (HPWA) is impregnated on it. The acidity of HPWA loading on Sn-MCM-41 was investigated by temperature programmed desorption of NH{sub 3}. The diffused reflectance spectra of ultraviolet radiation, Raman spectra, FT-IR, {sup 29}Si-MAS NMR and {sup 31}P-MAS NMR techniques revealed the intact of α-Keggin anions on Sn-MCM-41. The wide angle XRD results showed that the HPWA is well dispersed on the support. The total acidity was enhanced with increase in loading of H{sub 3}PW{sub 12}O{sub 40}. The catalytic activity was examined in desulfurization of dibenzothiophene in vapor phase system. Among the catalysts 18% HPWA loaded Sn-MCM-41 showed good catalytic activity in desulfurization at 325 °C. The HPWA/Sn-MCM-41 are a suitable solid acid catalyst for converting organic sulfur into insoluble sulfone.« less

Biodegradation of nonionic and anionic surfactants in domestic wastewater under simulated sewer conditions.

PubMed

Menzies, Jennifer Z; McDonough, Kathleen; McAvoy, Drew; Federle, Thomas W

2017-02-01

The ultimate disposition of chemicals discarded down the drain can be substantially impacted by their fate in the sewer, but to date limited data have been published on the biodegradability of chemicals in sewer systems. The recently established OECD 314 guideline (Simulation tests to assess the biodegradability of chemicals discharged in wastewater, 2008) contains a simulation method (314A) for evaluating the biodegradation of chemicals in sewage under simulated sewer conditions. This research used the OECD 314A method to evaluate the rates and pathways of primary and ultimate biodegradation of a suite of 14 C-labeled homologues representing four classes of high volume surfactants including nonionic alkyl ethoxylates (AE), and anionic alkyl ethoxysulfates (AES), alkyl sulfate (AS) and linear alkyl benzene sulfonate (LAS). All the tested homologues exhibited >97 % loss of parent, formation of metabolites, and some level (16-94 %) of CO 2 production after being incubated 96-100 h in raw domestic wastewater. Comparison of C 12 E 3 , C 14 E 3 , and C 16 E 3 showed that the first order biodegradation rate was affected by alkyl chain length with rates ranging from 6.8 h -1 for C 12 E 3 to 0.49 h -1 for C 16 E 3 . Conversely, comparison of C 14 E 1 , C 14 E 3 , and C 14 E 9 showed that the number of ethoxy units did not impact the biodegradation rate. AES and AS degraded quickly with first order kinetic rates of 1.9-3.7 and 41 h -1 respectively. LAS did not exhibit first order decay kinetics and primary degradation was slow. Biodegradation pathways were also determined. This work shows that biodegradation in the sewer has a substantial impact on levels of surfactants and surfactant metabolites that ultimately reach wastewater treatment plants.

Degradation and environmental risk of surfactants after the application of compost sludge to the soil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gonzalez, M.M.; Martin, J.; Camacho-Munoz, D.

2012-07-15

Highlights: Black-Right-Pointing-Pointer Degradation of surfactants in soil amended with sewage sludge during 100 days. Black-Right-Pointing-Pointer Temperature influences on the degradation of the studied compounds. Black-Right-Pointing-Pointer Overall, the LAS degradation is faster than the NP compounds degradation. Black-Right-Pointing-Pointer Therefore, the LAS presented lower environmental risk than the NP compounds. - Abstract: In this work, the degradation of anionic and non-ionic surfactants in agricultural soil amended with sewage sludge is reported. The compounds analysed were: linear alkylbenzene sulphonates (LAS) with a 10-13 carbon alkylic chain, and nonylphenolic compounds (NPE), including nonylphenol (NP) and nonylphenol ethoxylates with one and two ethoxy groups (NP1EOmore » and NP2EO). The degradation studies were carried out under winter (12.7 Degree-Sign C) and summer (22.4 Degree-Sign C) conditions in Andalusia region. The concentration of LAS was reduced to 2% of the initial concentration 100 day after sludge-application to the soil. The half-life time measured for LAS homologues were ranged between 4 and 14 days at 12.7 Degree-Sign C and between 4 and 7 days at 22.4 Degree-Sign C. With regard to NPE compounds, after 8 and 4 days from the beginning of the experiment at 12.7 and 22.4 Degree-Sign C, respectively, their concentration levels were increased to 6.5 and 13.5 mg/kg dm (dry matter) as consequence of the degradation of nonylphenol polyethoxylates. These concentration levels were reduced to 5% after 63 and 70 days for 12.7 Degree-Sign C and 22.4 Degree-Sign C, respectively. The half-life times measured for NPEs were from 8 to 16 days at 12.7 Degree-Sign C and from 8 to 18 days at 22.4 Degree-Sign C. Environmental risk assessment revealed that for LAS homologues no environment risk could be expected after 7 and 8 days of sludge application to the soil for 22.4 and 12.7 Degree-Sign C, respectively; however, potential toxic effects could be observed for the nonylphenolic compounds during the first 56 days after sludge application to the soil.« less

Rayleigh scattering of linear alkylbenzene in large liquid scintillator detectors.

PubMed

Zhou, Xiang; Liu, Qian; Wurm, Michael; Zhang, Qingmin; Ding, Yayun; Zhang, Zhenyu; Zheng, Yangheng; Zhou, Li; Cao, Jun; Wang, Yifang

2015-07-01

Rayleigh scattering poses an intrinsic limit for the transparency of organic liquid scintillators. This work focuses on the Rayleigh scattering length of linear alkylbenzene (LAB), which will be used as the solvent of the liquid scintillator in the central detector of the Jiangmen Underground Neutrino Observatory. We investigate the anisotropy of the Rayleigh scattering in LAB, showing that the resulting Rayleigh scattering length will be significantly shorter than reported before. Given the same overall light attenuation, this will result in a more efficient transmission of photons through the scintillator, increasing the amount of light collected by the photosensors and thereby the energy resolution of the detector.

[Preliminary Study on Linear Alkylbenzenes as Indicator for Process of Urbanization].

PubMed

Xu, Te; Zeng, Hui; Ni, Hong-Gang

2016-01-15

In this study, we selected Shenzhen City as a typical region of urbanization and took Linear alkylbenzenes ( LABs) as an environmental molecular marker to investigate the relationship between soil LABs levels and urbanization indexes on the basis of analysis of spatial distribution of LABs in surface soil. Our results indicated relations between the LABs levels in soil and the five urbanization indexes, such as the population, water supply, urban construction, income and expenditure, as well as industrial structure. These results suggested that LABs levels were correlated with urbanization and could be used as an environmental molecular indicator for the process of urbanization.

Effects of surfactants on the properties of mortar containing styrene/methacrylate superplasticizer.

PubMed

Negim, El-Sayed; Kozhamzharova, Latipa; Khatib, Jamal; Bekbayeva, Lyazzat; Williams, Craig

2014-01-01

The physical and mechanical properties of mortar containing synthetic cosurfactants as air entraining agent are investigated. The cosurfactants consist of a combination of 2% dodecyl benzene sodium sulfonate (DBSS) and either 1.5% polyvinyl alcohol (PVA) or 1.5% polyoxyethylene glycol monomethyl ether (POE). Also these cosurfactants were used to prepare copolymers latex: styrene/butyl methacrylate (St/BuMA), styrene/methyl methacrylate (St/MMA), and styrene/glycidyl methacrylate (St/GMA), in order to study their effects on the properties of mortar. The properties of mortar examined included flow table, W/C ratio, setting time, water absorption, compressive strength, and combined water. The results indicate that the latex causes improvement in mortar properties compared with cosurfactants. Also polymer latex containing DBSS/POE is more effective than that containing DBSS/PVA.

Effects of Surfactants on the Properties of Mortar Containing Styrene/Methacrylate Superplasticizer

PubMed Central

Negim, El-Sayed; Kozhamzharova, Latipa; Khatib, Jamal; Bekbayeva, Lyazzat; Williams, Craig

2014-01-01

The physical and mechanical properties of mortar containing synthetic cosurfactants as air entraining agent are investigated. The cosurfactants consist of a combination of 2% dodecyl benzene sodium sulfonate (DBSS) and either 1.5% polyvinyl alcohol (PVA) or 1.5% polyoxyethylene glycol monomethyl ether (POE). Also these cosurfactants were used to prepare copolymers latex: styrene/butyl methacrylate (St/BuMA), styrene/methyl methacrylate (St/MMA), and styrene/glycidyl methacrylate (St/GMA), in order to study their effects on the properties of mortar. The properties of mortar examined included flow table, W/C ratio, setting time, water absorption, compressive strength, and combined water. The results indicate that the latex causes improvement in mortar properties compared with cosurfactants. Also polymer latex containing DBSS/POE is more effective than that containing DBSS/PVA. PMID:24955426

Effect of Micellization on the Adsorption Kinetics of Polymeric Surfactants to the Solid/Water Interface

NASA Astrophysics Data System (ADS)

Toomey, Ryan; Tirrell, Matthew

2002-03-01

We have studied the adsorption kinetics of two classes of hydrophobic/ionic diblock copolymer surfactants in aqueous environments to understand the role that micellization plays in the adsorption process. The two systems studied were poly(t-butyl styrene)-block-poly(styrene sulfonate) (PtBS-b-PSS) and polystyrene-block-poly(acrylic acid) (PS-b-PAA). It is found that by changing the hydrophobicity of the adsorbing surface, micelle adsorption can be turned on or off. When micelle adsorption occurs, the initial adsorption rate is always slower than the supply rate of micelles to the surface, indicating “reaction-limited” adsorption. Since these micelles have essentially frozen cores, the adsorption cannot be explained by the release of unimers from the micelles. Rather, micelles directly adsorb, and they have to overcome the potential barrier imposed by their corona. Due to micellization, the adsorption rate can also be a complex function of ionic strength. A regime was found where the initial adsorption rate decreased with increasing ionic strength. This anomaly can be explained by the onset of micellization. As the salt concentration is increased, more micelles are formed. However micelles adsorb roughly an order of magnitude slower than free chains. Therefore, if increasing the ionic strength produces more micelles, the adsorption rate will simultaneously decrease.

Aggregation behavior and complex structure between triblock copolymer and anionic surfactants

NASA Astrophysics Data System (ADS)

Li, Yiming; Bao, Mutai; Wang, Zhining; Zhang, Haixia; Xu, Guiying

2011-01-01

The aggregation behavior and complex structure of ABA triblock copolymer EO 76PO 30EO 76 (F68) with sodium dodecyl sulfate (SDS) and sodium bis(2-ethylhexyl)sulfonate (AOT) in aqueous solution were investigated by surface tension, fluorescence techniques and dynamic light-scattering (DLS) measurements. It is revealed that in certain regions of binding, surfactant/F68 complexes are formed. Structural informations and size of complexes are evaluated. When F68 is present in its nonassociated state, F68/micellar SDS complexes are formed at SDS concentrations above its critical aggregation concentration (cac). The cac is well below the critical micellar concentration (cmc) of pure SDS, and a model suggesting how complexes are formed at the cac in the presence of F68 is described. Experimental results show that SDS interacts with F68 mainly through hydrophobic forces, polypropylene oxide (PPO) groups of F68 are solubilized into SDS micellar cores and poly(ethylene oxide) (PEO) groups interact with SDS micelles. This interaction mechanism results in a "pearl-necklace" complex structure. However, a different structure occurs for F68/AOT complex at lower F68 concentrations, as nonassociated F68 interacts with AOT mainly through ion-dipole interactions. Complexes with a "wrapping" structure at lower F68 concentrations are formed.

Parametric effects of turning Ti-6Al-4V alloys with aluminum oxide nanolubricants with SDBS

NASA Astrophysics Data System (ADS)

Ali, M. A. M.; Azmi, A. I.; Khalil, A. N. M.

2017-09-01

Applications of nanolubricants have been claimed to improve machinability of aerospace metals due to reduction of friction as a results of the rolling action of billions of nanoparticles at the tool-chip interface. In addition, the need to pursue for an eco-friendly machining has pushed researchers toward implementing alternative lubrication methods through minimal quantity lubrication (MQL). However, the gap in the current literature regarding the performance of nanolubricants via MQL has restricted the widespread use of this lubricant and technique in industries. The present work aims to understand the parametric effects of nanoparticles concentration, cutting speed, feed rate and nozzle angle during machining of titanium alloy, Ti-6AL-4V. Multiple performance of machinability outputs such as surface roughness, tool wear and power consumption were simultaneously determined via Taguchi orthogonal array and grey relational analyses. Prior to machining tests, the nanolubricants stabilities were investigated through the addition of surfactant; sodium dodecyl benzene sulfonate (SDBS). The results clearly indicated that inclusion of SDBS surfactant managed to reduce agglomeration in the base lubricant. Meanwhile, grey relational analyses revealed that the combination of 0.6 % nanoparticles concentration, cutting speed of 85 m/min, feed rate of 0.1 mm/rev and nozzle angle of 60o as desired setting for all the three machining outputs.

Effect of linear alkyl benzene sulfonates (LAS) on the fate of phenanthrene in a model ecosystem (water-lava-plant-air).

PubMed

Jiang, Xia; Jin, Xiang-can; Yan, Chang-zhou; Yediler, Ayfer; Ou, Zi-qing; Kettrup, Antonius

2004-01-01

Advanced closed chamber system was used to study the fate of phenanthrene (3-rings PAHs) in the presence of linear alkylbenzene sulphonates (LAS). The results showed mineralization and metabolism of phenanthrene are fast in the "culture solution-lava-plant-air" model ecological system. The distribution proportions of applied 14C-activity in this simulative ecological system were 41%-45%, 14% to 10% and 1% in plant, lava and culture solution respectively, and 18% to 29%, 11% to 8% recovered in the forms of VOCs and CO2. Main parts of the applied 14C-activity exist in two forms, one is polar metabolites (25%) which mainly distribute in the root (23%), the other is unextractable part (23%) which have been constructed into plant root (8.98%), shoot (0.53%) or bonded to lava (13.2%). The main metabolites of phenanthrene were polar compounds (25% of applied 14C-activity), and small portion of 14C-activity was identified as non-polar metabolites (6% of applied 14C-activity) and apparent phenanthrene (1.91% of applied 14C-activity). Phenanthrene and its metabolites can be taken up through plant roots and translocated to plant shoots. The presence of LAS significantly increased the the concentration of 14C-activity in the plant and production of VOCs, at the same time it decreased the phenanthrene level in the plant and the production of CO2 at the concentration of 200 mg/L.

Rayleigh scattering of linear alkylbenzene in large liquid scintillator detectors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Xiang, E-mail: xiangzhou@whu.edu.cn; Zhang, Zhenyu; Liu, Qian

2015-07-15

Rayleigh scattering poses an intrinsic limit for the transparency of organic liquid scintillators. This work focuses on the Rayleigh scattering length of linear alkylbenzene (LAB), which will be used as the solvent of the liquid scintillator in the central detector of the Jiangmen Underground Neutrino Observatory. We investigate the anisotropy of the Rayleigh scattering in LAB, showing that the resulting Rayleigh scattering length will be significantly shorter than reported before. Given the same overall light attenuation, this will result in a more efficient transmission of photons through the scintillator, increasing the amount of light collected by the photosensors and therebymore » the energy resolution of the detector.« less

Effective oxidation of benzylic and alkane C-H bonds catalyzed by sodium o-iodobenzenesulfonate with Oxone as a terminal oxidant under phase-transfer conditions.

PubMed

Cui, Li-Qian; Liu, Kai; Zhang, Chi

2011-04-07

Catalytic oxidation of benzylic C-H bonds could be efficiently realized using IBS as a catalyst which was generated in situ from the oxidation of sodium 2-iodobenzenesulfonate (1b) by Oxone in the presence of a phase-transfer catalyst, tetra-n-butylammonium hydrogen sulfate, in anhydrous acetonitrile at 60 °C. Various alkylbenzenes, including toluenes and ethylbenzenes, several oxygen-containing functionalities substituted alkylbenzenes, and a cyclic benzyl ether could be efficiently oxidized. And, the same reagent system of cat. 1b/Oxone/cat. n-Bu(4)NHSO(4) could be applied to the effective oxidation of alkanes as well.

Effects of Temperature and Humidity History on Brittleness of α-Sulfonated Fatty Acid Methyl Ester Salt Crystals.

PubMed

Watanabe, Hideaki; Morigaki, Atsunori; Kaneko, Yukihiro; Tobori, Norio; Aramaki, Kenji

2016-01-01

α-Sulfonated fatty acid methyl ester salts (MES), which were made from vegetable sources, are attractive candidates for eco-friendly washing detergents because they have various special features like excellent detergency, favorable biodegradability, and high stability against enzymes. To overcome some disadvantages of powder-type detergents like caking, sorting, and dusting, we studied how temperature and humidity history, as a model for long-term storage conditions, can affect crystalline structures and reduce the brittleness of MES powder. We characterized the crystalline structure of MES grains using small-angle X-ray scattering, wide-angle X-ray scattering, differential scanning calorimetry, and Fourier transform infrared spectroscopy measurements and determined the yield values, which measure the brittleness of MES grains, in shear stress using dynamic viscoelasticity measurements. This study confirmed that MES crystals form three pseudo-polymorphs via thermal or humidity conditioning: metastable crystals (αsubcell), anhydrous crystals (β subcell), and dihydrate crystals (β' subcell). Further, we found that the yield value increases upon phase transition from the β subcell to the β' subcell and from the β' subcell to the αsubcell. Therefore, controlling the thermal and humidity conditioning of MES grains is an effective way to decrease the brittleness of MES powders and can be used to overcome the above mentioned disadvantages of powder-type detergents in the absence of co-surfactants.

An erythrosin B-based "turn on" fluorescent sensor for detecting perfluorooctane sulfonate and perfluorooctanoic acid in environmental water samples.

PubMed

Cheng, Zhen; Du, Lingling; Zhu, Panpan; Chen, Qian; Tan, Kejun

2018-05-04

Because of the serious harm to animals and the environment associated with perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA), a rapid, sensitive and low-cost method for detecting PFOS and PFOA is of great importance. In this paper, a novel sensing method has been proposed for the highly sensitive detection of PFOS and PFOA in environmental water samples based on the "turn-on" switch of erythrosine B (EB)-hexadecyltrimethylammonium bromide (CTAB) system. In pH 8.55 Britton-Robinson (BR) buffer, EB can react with CTAB by electrostatic attraction, resulting in a strong fluorescence quenching of EB. With a subsequent addition of the CTAB, a red-shift occurred (11 nm), followed by a significant increase in fluorescence at high surfactant concentrations. It was found that PFOS and PFOA can obviously enhance fluorescence intensity of EB-CTAB system. The enhanced fluorescence intensity is proportional to the concentration of PFOS and PFOA in the range of 0.05-10 μM with detection limit of 12.8 nM and 11.8 nM (3σ), respectively. The presented assay has been successfully applied to sensing PFOS and PFOA in real water samples with RSD ≤ 4.3% and 2.9%, respectively. Copyright © 2018 Elsevier B.V. All rights reserved.

Three-way spectrofluorimetric-assisted multivariate determination of nonylphenol ethoxylate and 2-naphtalene sulfonate in wastewater samples and optimization approach for their photocatalytic degradation by CoTiO3 nanostructure.

PubMed

Mohsenikia, Atefeh; Gholami, Ali; Masoum, Saeed; Abbasi, Saleheh

2017-09-01

This study presents a new strategy for the simultaneous quantification of two industrial contaminants. The excitation-emission fluorescence data matrix combined with a three-way chemometric method, such as parallel factor analysis, was used for the determination of nonylphenol ethoxylate (NPE-9) as a nonionic surfactant and 2-naphthalene sulfonate (2-NS) in waste water samples. It is noticeable that this method can resolve overlapping signal into spectral and relative concentration profiles. By spiking the known concentrations of these compounds in the wastewater samples, the accuracy of the proposed methods was validated and recoveries of the spiked values were calculated. High recoveries (i.e. 90-110%) obtained for the waste water samples indicate the present method can be used successfully to determine the analytes concentration in the environmental contaminations. The photocatalytic degradation of NPE-9 and 2-NS in aqueous solution was studied using the CoTiO 3 nanoparticles catalyst. It was synthesized by the sol-gel technique. The catalytic activity of the prepared nanoparticles was measured in a batch photoreactor containing appropriate solutions of these compounds with UV irradiation. The photodegradation process of these compounds was optimized by using the central composite design. The CoTiO 3 showed high activity for UV-photocatalytic degradation of NPE-9 and 2-NS.

The Effects of Perfluorinated Chemicals on Adipoctye ...

EPA Pesticide Factsheets

The 3T3-L1 preadipocyte culture system has been used to examine numerous compounds that influence adipocyte differentiation or function. The perfluoroalkyl acids (PFAAs), used as surfactants in a variety of industrial applications, are of concern as environmental contaminants that are detected worldwide in human serum and animal tissues. This study was designed to evaluate the potential for PFAAs to affect adipocyte differentiation and lipid accumulation using mouse 3T3-L1 cells. Cells were treated with perfluorooctanoic acid (PFOA) (5-100 IJM), perfluorononanoic acid (PFNA) (5-100 1JM), perfluorooctane sulfonate (PFOS) (50-300 IJM}, perfluorohexane sulfonate (PFHxS) (40-250 IJM), the peroxisome proliferator activated receptor (PPAR) PPARa agonist Wyeth-14,643 (WY-14,643), and the PPARy agonist rosiglitazone. The PPARy agonist was included as a positive control as this pathway is critical to adipocyte differentiation. The PPARa agonist was included as the PFAA compounds are known activators of this pathway. Cells were assessed morphometrically and biochemically for number, size, and lipid content. RNA was extracted for qPCR analysis of 13 genes selected for their importance in adipocyte differentiation and lipid metabolism. There was a significant concentration-related increase in cell number and decreased cell size after exposure to PFOA, PFHxS, PFOS, and PFNA. All four PFAA treatments produced a concentration-related decrease in the calculated average area oc

Effects of perfluorinated chemicals on adipocyte development ...

EPA Pesticide Factsheets

Obesity is a growing concern in the US population. Current interest is high in the role played by environmental factors called obesogens that may contribute to obesity through developmental exposure. One class of potential obesogens is the family of perfluorinated chemicals used as surfactants in a variety of industrial applications. Given the importance of understanding the role these compounds play in lipid homeostasis we used pre-adipocyte 3T3-L1 mouse fibroblast cells (Zen-Bio, RTP NC) to study their effects on adipogenesis and lipid accumulation. These cells differentiate into adipocytes accumulating large lipid droplets. Cultures were treated with perfluorooctanoic acid (PFOA) (1-200uM), perfluorononanoic acid (PFNA) (5-lOOuM), perfluorooctane sulfonate (PFOS) (5O-300uM), and perfluorohexane sulfonate (PFHxS) (40- 250uM). Cell size number, and lipid content were assessed using morphomeiric analysis. All four compounds decreased cell size compared to control, and PFNA was most potent, in terms of lowest observed effect concentration (LOEC), whereas PFOA was least potent. Cell number increased for all perfluorinated chemicals tested, most potently for PFNA and least for PFOS. Interestingly, average lipid area per cell for all four chemicals decreased compared to control, but PFOS and PFHxS had increased total lipid area. Additionally, significant increases in total triglyceride were noted for all compounds compared to controls. PFOA and PFNA increased trigly

Effect of increased groundwater viscosity on the remedial performance of surfactant-enhanced air sparging

NASA Astrophysics Data System (ADS)

Choi, Jae-Kyeong; Kim, Heonki; Kwon, Hobin; Annable, Michael D.

2018-03-01

The effect of groundwater viscosity control on the performance of surfactant-enhanced air sparging (SEAS) was investigated using 1- and 2-dimensional (1-D and 2-D) bench-scale physical models. The viscosity of groundwater was controlled by a thickener, sodium carboxymethylcellulose (SCMC), while an anionic surfactant, sodium dodecylbenzene sulfonate (SDBS), was used to control the surface tension of groundwater. When resident DI water was displaced with a SCMC solution (500 mg/L), a SDBS solution (200 mg/L), and a solution with both SCMC (500 mg/L) and SDBS (200 mg/L), the air saturation for sand-packed columns achieved by air sparging increased by 9.5%, 128%, and 154%, respectively, (compared to that of the DI water-saturated column). When the resident water contained SCMC, the minimum air pressure necessary for air sparging processes increased, which is considered to be responsible for the increased air saturation. The extent of the sparging influence zone achieved during the air sparging process using the 2-D model was also affected by viscosity control. Larger sparging influence zones (de-saturated zone due to air injection) were observed for the air sparging processes using the 2-D model initially saturated with high-viscosity solutions, than those without a thickener in the aqueous solution. The enhanced air saturations using SCMC for the 1-D air sparging experiment improved the degradative performance of gaseous oxidation agent (ozone) during air sparging, as measured by the disappearance of fluorescence (fluorescein sodium salt). Based on the experimental evidence generated in this study, the addition of a thickener in the aqueous solution prior to air sparging increased the degree of air saturation and the sparging influence zone, and enhanced the remedial potential of SEAS for contaminated aquifers.

Laundry Detergency of Solid Non-Particulate Soil Using Microemulsion-Based Formulation.

PubMed

Chanwattanakit, Jarussri; Chavadej, Sumaeth

2018-02-01

Laundry detergency of solid non-particulate soil on polyester and cotton was investigated using a microemulsion-based formulation, consisting of an anionic extended surfactant (C 12,13 -4PO-SO 4 Na) and sodium mono-and di-methyl naphthalene sulfonate (SMDNS) as the hydrophilic linker, to provide a Winsor Type III microemulsion with an ultralow interfacial tension (IFT). In this work, methyl palmitate (palmitic acid methyl ester) having a melting point around 30°C, was used as a model solid non-particulate (waxy) soil. A total surfactant concentration of 0.35 wt% of the selected formulation (4:0.65 weight ratio of C 12,13 -4PO-SO 4 Na:SMDNS) with 5.3 wt% NaCl was able to form a middle phase microemulsion at a high temperature (40°C),which provided the highest oil removal level with the lowest oil redeposition and the lowest IFT, and was much higher than that with a commercial detergent or de-ionized water. Most of the detached oil, whether in liquid or solid state, was in an unsolubilized form. Hence, the dispersion stability of the detached oil droplets or solidified oil particles that resulted from the surfactant adsorption played an important role in the oil redeposition. For an oily detergency, the lower the system IFT, the higher the oil removal whereas for a waxy (non-particulate) soil detergency, the lower the contact angle, the higher the solidified oil removal. For a liquefied oil, the detergency mechanism was roll up and emulsification with dispersion stability, while that for the waxy soil (solid oil) was the detachment by wettability with dispersion stability.

CEC with new monolithic stationary phase based on a fluorinated monomer, trifluoroethyl methacrylate.

PubMed

Yurtsever, Arda; Saraçoğlu, Berna; Tuncel, Ali

2009-02-01

A new, fluorinated monolithic stationary phase for CEC was first synthesized by a single-stage, thermally initiated copolymerization of a fluorinated monomer, 2,2,2-trifluoroethyl methacrylate (TFEM) and ethylene dimethacrylate (EDMA) in the presence of a porogen mixture. In this preparation, 2-acrylamido-2-methyl-1-propanesulfonic acid was used as the charge-bearing monomer. The porogen mixture was prepared by mixing isoamylalcohol and 1,4-butanediol. A clear increase in the electroosmotic mobility was observed with increasing pH. The electroosmotic mobility decreased with increasing ACN concentration. Poly(TFEM-co-EDMA) monolith prepared under optimized polymerization conditions was successfully used in the separation of alkylbenzenes and phenols by CEC. The best chromatographic separation for alkylbenzenes was performed with lower ACN concentrations (i.e. 60% v/v) with respect to the common acrylic-based CEC monoliths. The theoretical plate numbers up to 220 000 plates/m were achieved in the reversed phase separation of phenols. Poly(TFEM-co-EDMA) monolith also allowed the simultaneous separation of aniline and benzoic acid derivatives by a single run and by using a lower ACN concentration in the mobile phase with respect to the similar electrochromatographic separations. A stable retention behaviour in reversed phase separation of alkylbenzenes was obtained with the poly(TFEM-co-EDMA) monolith.

Highly crosslinked polymeric monoliths for reversed-phase capillary liquid chromatography of small molecules.

PubMed

Liu, Kun; Tolley, H Dennis; Lee, Milton L

2012-03-02

Seven crosslinking monomers, i.e., 1,3-butanediol dimethacrylate (1,3-BDDMA), 1,4-butanediol dimethacrylate (1,4-BDDMA), neopentyl glycol dimethacrylate (NPGDMA), 1,5-pentanediol dimethacrylate (1,5-PDDMA), 1,6-hexanediol dimethacrylate (1,6-HDDMA), 1,10-decanediol dimethacrylate (1,10-DDDMA), and 1,12-dodecanediol dimethacrylate (1,12-DoDDMA), were used to synthesize highly cross-linked monolithic capillary columns for reversed-phase liquid chromatography (RPLC) of small molecules. Dodecanol and methanol were chosen as "good" and "poor" porogenic solvents, respectively, for these monoliths, and were investigated in detail to provide insight into the selection of porogen concentration using 1,12-DoDDMA. Isocratic elution of alkylbenzenes at a flow rate of 300 nL/min was conducted for all of the monoliths. Gradient elution of alkylbenzenes and alkylparabens provided high resolution separations. Optimized monoliths synthesized from all seven crosslinking monomers showed high permeability. Several of the monoliths demonstrated column efficiencies in excess of 50,000 plates/m. Monoliths with longer alkyl-bridging chains showed very little shrinking or swelling in solvents of different polarities. Column preparation was highly reproducible; the relative standard deviation (RSD) values (n=3) for run-to-run and column-to-column were less than 0.25% and 1.20%, respectively, based on retention times of alkylbenzenes. Copyright © 2012 Elsevier B.V. All rights reserved.

Aspects of droplet and particle size control in miniemulsions

NASA Astrophysics Data System (ADS)

Saygi-Arslan, Oznur

Miniemulsion polymerization has become increasingly popular among researchers since it can provide significant advantages over conventional emulsion polymerization in certain cases, such as production of high-solids, low-viscosity latexes with better stability and polymerization of highly water-insoluble monomers. Miniemulsions are relatively stable oil (e.g., monomer) droplets, which can range in size from 50 to 500 nm, and are normally dispersed in an aqueous phase with the aid of a surfactant and a costabilizer. These droplets are the primary locus of the initiation of the polymerization reaction. Since particle formation takes place in the monomer droplets, theoretically, in miniemulsion systems the final particle size can be controlled by the initial droplet size. The miniemulsion preparation process typically generates broad droplet size distributions and there is no complete treatment in the literature regarding the control of the mean droplet size or size distribution. This research aims to control the miniemulsion droplet size and its distribution. In situ emulsification, where the surfactant is synthesized spontaneously at the oil/water interface, has been put forth as a simpler method for the preparation of miniemulsions-like systems. Using the in situ method of preparation, emulsion stability and droplet and particle sizes were monitored and compared with conventional emulsions and miniemulsions. Styrene emulsions prepared by the in situ method do not demonstrate the stability of a comparable miniemulsion. Upon polymerization, the final particle size generated from the in situ emulsion did not differ significantly from the comparable conventional emulsion polymerization; the reaction mechanism for in situ emulsions is more like conventional emulsion polymerization rather than miniemulsion polymerization. Similar results were found when the in situ method was applied to controlled free radical polymerizations (CFRP), which have been advanced as a potential application of the method. Molecular weight control was found to be achieved via diffusion of the CFRP agents through the aqueous phase owing to limited water solubilities. The effects of adsorption rate and energy on the droplet size and size distribution of miniemulsions using different surfactants (sodium lauryl sulfate (SLS), sodium dodecylbenzene sulfonate (SDBS), Dowfax 2A1, Aerosol OT-75PG, sodium n-octyl sulfate (SOS), and sodium n-hexadecyl sulfate (SHS)) were analyzed. For this purpose, first, the dynamics of surfactant adsorption at an oil/water interface were examined over a range of surfactant concentrations by the drop volume method and then adsorption rates of the different surfactants were determined for the early stages of adsorption. The results do not show a direct relationship between adsorption rate and miniemulsion droplet size and size distribution. Adsorption energies of these surfactants were also calculated by the Langmuir adsorption isotherm equation and no correlation between adsorption energy and miniemulsion droplet size was found. In order to understand the mechanism of miniemulsification process, the effects of breakage and coalescence processes on droplet size distributions were observed at different surfactant concentrations, monomer ratios, and homogenization conditions. A coalescence and breakup mechanism for miniemulsification is proposed to explain the size distribution of droplets. The multimodal droplet size distribution of ODMA miniemulsions was controlled by the breakage mechanism. The results also showed that, at a surfactant concentration when 100% surface coverage was obtained, the droplet size distribution became unimodal.

Effect of Organic Loading Rates on biodegradation of linear alkyl benzene sulfonate, oil and grease in greywater by Integrated Fixed-film Activated Sludge (IFAS).

PubMed

Eslami, Hadi; Ehrampoush, Mohammad Hassan; Ghaneian, Mohammad Taghi; Mokhtari, Mehdi; Ebrahimi, Aliasghar

2017-05-15

In this study, performance of Integrated Fixed-film Activated Sludge (IFAS) system in treatment of Linear Alkylbenzene Sulfonate (LAS), and oil & grease in synthetic greywater and effect of Organic Loading Rates (OLRs) on removal efficiency within a period of 105 days were investigated. Present study was carried out in a pilot scale under such conditions as temperature of 30 ± 1 °C, dissolved oxygen of 2.32 ± 0.91 mg/l, pH of 8.01 ± 0.95 and OLRs of 0.11-1.3gCOD/L.d. Also, Scanning Electron Microscopy (SEM) images were employed to specify rate of the biofilm formed on the media inside the reactor IFAS. The best removal efficiency for COD, LAS and oil and grease were respectively obtained as 92.52%, 94.24% and 90.07% in OLR 0.44gCOD/L.d. The assessment of loading rate indicated that with increased OLR to 0.44gCOD/L.d, removal efficiency of COD, oil and grease was increased while with increased OLR, removal efficiency was decreased. In doing so, based on the statistical test ANOVA, such a difference between removal efficiencies in diverse OLRs was significant for COD (p = 0.003), oil and grease (p = 0.01). However, in terms of LAS, with increased value of OLR to 0.44gCOD/L.d, the removal efficiency was increased and then with higher OLRs, removal efficiency was slightly decreased that is insignificant (p = 0.35) based on the statistical test ANOVA. The SEM images also showed that the biofilm formed on the media inside IFAS reactor plays a considerable role in adsorption and biodegradation of LAS, and oil & grease in greywater. The linear relation between inlet COD values and rate of removed LAS indicated that the ratio of inlet COD (mg/L) to removed LAS (mg/L) was 0.4. Therefore, use of IFAS system for biodegradation of LAS, oil and grease in greywater can be an applicable option. Copyright © 2017 Elsevier Ltd. All rights reserved.

Theoretical study of structure and stability of small gadolinium carboxylate complexes in liquid scintillator solvents.

PubMed

Huang, Pin-Wen

2014-09-01

The structural properties of three small gadolinium carboxylate complexes in three liquid scintillator solvents (pseudocumene, linear alkylbenzene, and phenyl xylylethane) were theoretically investigated using density functional theory (B3LYP/LC-RECP) and polarizable continuum model (PCM). The average interaction energy between gadolinium atom and carboxylate ligand (E(int)) and the energy difference of the highest singly occupied molecular orbital and lowest unoccupied molecular orbital (Δ(SL)) were calculated to evaluate and compare the relative stability of these complexes in solvents. The calculation results show that the larger (with a longer alkyl chain) gadolinium carboxylate complex has greater stability than the smaller one, while these gadolinium carboxylates in linear alkylbenzene were found to have greater stability than those in the other two solvents.

Enhancement of toughness and wear resistance in boron nitride nanoplatelet (BNNP) reinforced Si3N4 nanocomposites

PubMed Central

Lee, Bin; Lee, Dongju; Lee, Jun Ho; Ryu, Ho Jin; Hong, Soon Hyung

2016-01-01

Ceramics have superior hardness, strength and corrosion resistance, but are also associated with poor toughness. Here, we propose the boron nitride nanoplatelet (BNNP) as a novel toughening reinforcement component to ceramics with outstanding mechanical properties and high-temperature stability. We used a planetary ball-milling process to exfoliate BNNPs in a scalable manner and functionalizes them with polystyrene sulfonate. Non-covalently functionalized BNNPs were homogeneously dispersed with Si3N4 powders using a surfactant and then consolidated by hot pressing. The fracture toughness of the BNNP/Si3N4 nanocomposite increased by as much as 24.7% with 2 vol.% of BNNPs. Furthermore, BNNPs enhanced strength (9.4%) and the tribological properties (26.7%) of the ceramic matrix. Microstructural analyzes have shown that the toughening mechanisms are combinations of the pull-out, crack bridging, branching and blunting mechanisms. PMID:27271465

Polymerized Paired Ions as Polymeric Ionic Liquid-Proton Conductivity.

PubMed

Gu, Hong; Yan, Feng; Texter, John

2016-07-01

A new polymerized ionic liquid has been derived by photopolymerization of a stimuli-responsive ionic liquid surfactant, ILAMPS, which is composed of polymerizable, paired ions. The cation is 1-methyl-3-[11-(acryloyloxy)undecyl] imidazolium (IL), and the anion is 2-acrylamido-2-methyl-1-propanesulfonate (AMPS). This ion combination is a new ionic liquid. The resulting hygroscopic resins are highly polarizable, suitable for sensor design and for ultracapacitor fabrication and proton conducting. Interactions of imidazolium with anions provide basis for stimuli-responsiveness, and are used to promote proton transport. Doping with one equivalent of HPF6 at 0% relative humidity produces a 100-fold increase in proton conductivity at 100-125 °C and activation energies for proton transport lower than those of Nafion at water loadings less than 5 per sulfonate. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Improved electrical conductivity of poly(ethylene oxide) nanofibers using multi-walled carbon nanotubes

NASA Astrophysics Data System (ADS)

Lee, J. Y.; Kang, T.-H.; Choi, J. H.; Choi, I.-S.; Yu, W.-R.

2018-03-01

Highly conductive nanofibers with 1570 S/m were obtained from an electrospun solution of polymer containing multiwalled carbon nanotubes (MWCNTs). Homogeneous dispersion of high concentrations of MWCNTs was achieved by attaching poly(styrenesulfonic acid graft aniline) (PSS-g-ANI), an amphiphilic surfactant, to the MWCNT surface. The hydrophilic sulfonic acid group facilitated the dissolution of PSS-g-ANI-grafted MWCNTs in a polyethylene oxide (PEO) solution up to 6.7 wt% MWCNT. To our knowledge, this is the highest level of MWCNT doping attained in a solution designed for electrospinning. With the incorporation of PSS-g-ANI, the concentration of MWCNTs embedded in the electrospun nanofibers increased. More importantly, the alignment of MWCNTs along the nanofiber axis increased significantly, as confirmed by observed birefringence under crossed polarizers. The combination of higher doping levels and better alignment afforded highly conductive nanofibers suitable for electronic nanodevices.

Polymer electrolyte membrane assembly for fuel cells

NASA Technical Reports Server (NTRS)

Yen, Shiao-Ping S. (Inventor); Kindler, Andrew (Inventor); Yavrouian, Andre (Inventor); Halpert, Gerald (Inventor)

2002-01-01

An electrolyte membrane for use in a fuel cell can contain sulfonated polyphenylether sulfones. The membrane can contain a first sulfonated polyphenylether sulfone and a second sulfonated polyphenylether sulfone, wherein the first sulfonated polyphenylether and the second sulfonated polyphenylether sulfone have equivalent weights greater than about 560, and the first sulfonated polyphenylether and the second sulfonated polyphenylether sulfone also have different equivalent weights. Also, a membrane for use in a fuel cell can contain a sulfonated polyphenylether sulfone and an unsulfonated polyphenylether sulfone. Methods for manufacturing a membrane electrode assemblies for use in fuel cells can include roughening a membrane surface. Electrodes and methods for fabricating such electrodes for use in a chemical fuel cell can include sintering an electrode. Such membranes and electrodes can be assembled into chemical fuel cells.

Polymer electrolyte membrane assembly for fuel cells

NASA Technical Reports Server (NTRS)

Yen, Shiao-Ping S. (Inventor); Kindler, Andrew (Inventor); Yavrouian, Andre (Inventor); Halpert, Gerald (Inventor)

2000-01-01

An electrolyte membrane for use in a fuel cell can contain sulfonated polyphenylether sulfones. The membrane can contain a first sulfonated polyphenylether sulfone and a second sulfonated polyphenylether sulfone, wherein the first sulfonated polyphenylether and the second sulfonated polyphenylether sulfone have equivalent weights greater than about 560, and the first sulfonated polyphenylether and the second sulfonated polyphenylether sulfone also have different equivalent weights. Also, a membrane for use in a fuel cell can contain a sulfonated polyphenylether sulfone and an unsulfonated polyphenylether sulfone. Methods for manufacturing a membrane electrode assemblies for use in fuel cells can include roughening a membrane surface. Electrodes and methods for fabricating such electrodes for use in a chemical fuel cell can include sintering an electrode. Such membranes and electrodes can be assembled into chemical fuel cells.

An Investigation of Carbon-Based Nanomaterials for Efficient Energy Production And Delivery

NASA Astrophysics Data System (ADS)

Gangoli, Varun Shenoy

Carbon-based nanomaterials have been demonstrated to have different potential applications in the energy industry. However, there are challenges in the realization of these applications. Chirality of single wall carbon nanotubes (SWCNTs) defines their electronic properties, and obtaining an ensemble of SWCNTs of the same chirality has been a problem studied for over two decades with no clear solution yet. Other carbon-based nanomaterials, such as carbon black aggregates, are hydrophobic in nature and potential applications in the oil and gas industry require their dispersal in an aqueous solvent. Another application in the oil and gas industry is enhanced oil recovery (EOR), and here there is a need for an inexpensive, stable, and efficient surfactant compared to currently used industrial solutions. The challenge of producing SWCNTs of the same chirality is studied using two approaches--separation after synthesis of SWCNTs of mixed chiralities, and chemical control over chirality of as-synthesized SWCNTs. Agarose gel-based affinity chromatography was used as a means towards highly semiconductor- enriched SWCNTs using a family of nonionic surfactants. UV-vis-NIR spectroscopy, Raman spectroscopy and photoluminescence spectroscopy was used to quantify the separation efficiency of the metal- and semiconductor-enriched SWCNTs. This process is an improvement over other chromatography-based techniques at the time in that the nonionic surfactants used are less expensive, enable a higher purity of semiconductor SWCNTs (>95%) and decompose fully by simply heating in air thus leaving behind pristine SWCNTs. The second approach was based on using catalyst dopants to preferentially synthesize SWCNTs of a particular chirality at the expense of SWCNTs of other chiralities. Heterogeneous catalysis combined with the screw dislocation theory of SWCNT growth provided the background for this work, and both selenium and phosphorus were identified as chemical dopants for iron catalysts. Both selenium and phosphorus were demonstrated to have a direct effect on the average number density and length of SWCNTs, and selenium also was shown to have a direct control over the growth rate of SWCNTs. This, combined with some preliminary spectroscopy results, suggest chiral control over the carbon nanotubes. Collaborative work on phase transfer of hydrophobic carbon-based nanomaterials into aqueous solvents for applications including saturated oil residual (SOR) detection and quantification in underground reservoirs helped recognize the potential of hydrophobically modified polymers as surfactants for EOR. Polystyrene sulfonate was chosen as the polymer of study owing to ease of availability, low cost of the precursor material and aromatic sulfonates already being studied for EOR. Controlled desulfonation of PSS was achieved by rapid heating of an aqueous solution of PSS in a microwave reactor under acidic conditions, with the reactant temperature and pH having a strong effect on the degree of desulfonation of the product ranging from 4.9% (as-obtained PSS) to 40%. Dynamic light scattering of the desulfonated PSS (termed PDS) in brine showed good stability of the polymer aggregates at temperatures as high as 150 °C, and tensiometry with aromatic oils such as toluene and aliphatic oils such as Isopar L showed good surface activity with interfacial tension going as low as 10-2 mN/m. Breakthrough experiments with sand packed columns at the lab scale, and core flooding at an independent facility confirmed good propagation of PDS through materials such as Berea sandstone, with minimal plugging and adsorption losses.

The synthesis and characterization of environmentally-responsive water-swellable and water-soluble polymers for wastewater remediation

NASA Astrophysics Data System (ADS)

Armentrout, Rodney Scott

The primary research goal is the development of new polymeric materials that demonstrate the environmentally-responsive sequestration of common water foulants, including surfactants and oils. Water-swellable and water-soluble polymers have been synthesized, structurally characterized, and their physical properties have been determined. In addition, the ability of the materials to sequester model water foulants has been evaluated. Anionic crosslinked polymer networks of 2-acrylamido-2-methyl-1-propanesulfonic acid, acrylamide, and methylene bisacrylamide have been synthesized and characterized by determining the equilibrium water contents as a function of ionic content of the polymer network. The molar ratio of bound surfactant to ionic group was determined to be less than one for all hydrogels studied, indicating an ion-exchange binding mechanism with minimal hydrophobic interactions between bound and unbound surfactant molecules is responsible for surfactant binding. Cationic crosslinked cyclopolymer networks of N,N-diallyl- N-methyl amine (DAMA) and N,N,N,N-tetraallyl ammonium chloride (TAAC) have been synthesized and characterized by determining the equilibrium water content as a function of pH. A maximum in the equilibrium water content is observed for pH-6 when the polymer is fully ionized. The solubilization of a model water foulant, p-cresol, by the polymeric surfactant, Pluronic F127, has been studied via equilibrium dialysis, dynamic light scattering and ultrafiltration experiments. It has been shown that at 25°C p-cresol is readily solubilized by F127 since the polymeric surfactant exists in a multimer conformation. Ultrafiltration experiments have demonstrated that the polymer-foulant binding interactions are largely unaffected by shear in a hollow fiber membrane. Copolymers of the zwitterionic monomer, 3-(N,N-diallyl- N-methyl ammonio) propane sulfonate (DAMAPS) and N,N-diallyl- N,N-dimethylammonium chloride (DADMAC) (the DADS series) or the pH-responsive hydrophobic monomer, N,N-diallyl-N-methyl amine (DAMA) (the DAMS series) have been prepared in a 0.5 M NaCl aqueous solution using 2-hydroxy-1-[4-(hydroxy-ethoxy)phenyl]-2-methyl-1-propanone (Irgacure 2959) as the free-radical photoinitiator. 13C NMR data indicate that the resulting polymers maintain the five-membered ring structure in the cis conformation common to diallylammonium salts. Equilibrium dialysis experiments demonstrate that pH-responsive hydrophobic microdomain formation may be utilized to control the solubilization of the organic solute, p-cresol. Ultrafiltration experiments have demonstrated that the polymer-foulant binding interactions are largely unaffected by shear in a hollow fiber membrane. Macromolecular aggregates of the poly( N,N-diallyl-N-methyl amine)/p-cresol complexes lead to fouling of the ultrafiltration membrane. However, incorporation of the sulfobetaine moiety hinders the formation of the macroscopic structures and higher permeate flux rates are achieved. (Abstract shortened by UMI.)

40 CFR 60.667 - Chemicals affected by subpart NNN.

Code of Federal Regulations, 2010 CFR

2010-07-01

... alcohols, ethoxylated, mixed Linear alcohols, ethoxylated, and sulfated, sodium salt, mixed Linear alcohols, sulfated, sodium salt, mixed Linear alkylbenzene 123-01-3 Magnesium acetate 142-72-3 Maleic anhydride 108...

40 CFR 60.667 - Chemicals affected by subpart NNN.

Code of Federal Regulations, 2011 CFR

2011-07-01

... alcohols, ethoxylated, mixed Linear alcohols, ethoxylated, and sulfated, sodium salt, mixed Linear alcohols, sulfated, sodium salt, mixed Linear alkylbenzene 123-01-3 Magnesium acetate 142-72-3 Maleic anhydride 108...

A renaissance of soaps? - How to make clear and stable solutions at neutral pH and room temperature.

PubMed

Wolfrum, Stefan; Marcus, Julien; Touraud, Didier; Kunz, Werner

2016-10-01

Soaps are the oldest and perhaps most natural surfactants. However, they lost much of their importance since "technical surfactants", usually based on sulfates or sulfonates, have been developed over the last fifty years. Indeed, soaps are pH- and salt-sensitive and they are irritant, especially to the eyes. In food emulsions, although authorized, they have a bad taste, and long-chain saturated soaps have a high Krafft temperature. We believe that most or perhaps all of these problems can be solved with modern formulation approaches. We start this paper with a short overview of our present knowledge of soaps and soap formulations. Then we focus on the problem of the lacking soap solubility at neutral pH values. For example, it is well known that with the food emulsifier sodium oleate (NaOl), clear and stable aqueous solutions can only be obtained at pH values higher than 10. A decrease in the pH value leads to turbid and unstable solutions. This effect is not compatible with the formulation of aqueous stable and drinkable formulations with neutral or even acidic pH values. However, the pH value/phase behavior of aqueous soap solutions can be altered by the addition of other surfactants. Such a surfactant can be Rebaudioside A (RebA), a steviol glycoside from the plant Stevia rebaudiana which is used as a natural food sweetener. In a recent paper, we showed the influence of RebA on the apKa value of sodium oleate in a beverage microemulsion and on its clearing temperature. In the present paper, we report on the effect of the edible bio-surfactant RebA, on the macroscopic and microscopic phase behavior of simple aqueous sodium oleate solutions at varying pH values. The macroscopic phase behavior is investigated by visual observation and turbidity measurements. The microscopic phase behavior is analyzed by acid-base titration curves, phase-contrast and electron microscopy. It turned out that even at neutral pH, aqueous NaOl/RebA solutions can be completely clear and stable for more than 50days at room temperature. This is for the first time that a long chain soap could be really solubilized in water at neutral pH at room temperature. At last, these findings were applied to prepare stable, highly translucent and drinkable aqueous solutions of omega-3-fatty acids at a pH value of 7.5. Copyright © 2016 Elsevier B.V. All rights reserved.

Quantitative structure-retention relationships for gas chromatographic retention indices of alkylbenzenes with molecular graph descriptors.

PubMed

Ivanciuc, O; Ivanciuc, T; Klein, D J; Seitz, W A; Balaban, A T

2001-02-01

Quantitative structure-retention relationships (QSRR) represent statistical models that quantify the connection between the molecular structure and the chromatographic retention indices of organic compounds, allowing the prediction of retention indices of novel, not yet synthesized compounds, solely from their structural descriptors. Using multiple linear regression, QSRR models for the gas chromatographic Kováts retention indices of 129 alkylbenzenes are generated using molecular graph descriptors. The correlational ability of structural descriptors computed from 10 molecular matrices is investigated, showing that the novel reciprocal matrices give numerical indices with improved correlational ability. A QSRR equation with 5 graph descriptors gives the best calibration and prediction results, demonstrating the usefulness of the molecular graph descriptors in modeling chromatographic retention parameters. The sequential orthogonalization of descriptors suggests simpler QSRR models by eliminating redundant structural information.

Versatile transformations of hydrocarbons in anaerobic bacteria: substrate ranges and regio- and stereo-chemistry of activation reactions†

PubMed Central

Jarling, René; Kühner, Simon; Basílio Janke, Eline; Gruner, Andrea; Drozdowska, Marta; Golding, Bernard T.; Rabus, Ralf; Wilkes, Heinz

2015-01-01

Anaerobic metabolism of hydrocarbons proceeds either via addition to fumarate or by hydroxylation in various microorganisms, e.g., sulfate-reducing or denitrifying bacteria, which are specialized in utilizing n-alkanes or alkylbenzenes as growth substrates. General pathways for carbon assimilation and energy gain have been elucidated for a limited number of possible substrates. In this work the metabolic activity of 11 bacterial strains during anaerobic growth with crude oil was investigated and compared with the metabolite patterns appearing during anaerobic growth with more than 40 different hydrocarbons supplied as binary mixtures. We show that the range of co-metabolically formed alkyl- and arylalkyl-succinates is much broader in n-alkane than in alkylbenzene utilizers. The structures and stereochemistry of these products are resolved. Furthermore, we demonstrate that anaerobic hydroxylation of alkylbenzenes does not only occur in denitrifiers but also in sulfate reducers. We propose that these processes play a role in detoxification under conditions of solvent stress. The thermophilic sulfate-reducing strain TD3 is shown to produce n-alkylsuccinates, which are suggested not to derive from terminal activation of n-alkanes, but rather to represent intermediates of a metabolic pathway short-cutting fumarate regeneration by reverse action of succinate synthase. The outcomes of this study provide a basis for geochemically tracing such processes in natural habitats and contribute to an improved understanding of microbial activity in hydrocarbon-rich anoxic environments. PMID:26441848

Effect of increased groundwater viscosity on the remedial performance of surfactant-enhanced air sparging.

PubMed

Choi, Jae-Kyeong; Kim, Heonki; Kwon, Hobin; Annable, Michael D

2018-03-01

The effect of groundwater viscosity control on the performance of surfactant-enhanced air sparging (SEAS) was investigated using 1- and 2-dimensional (1-D and 2-D) bench-scale physical models. The viscosity of groundwater was controlled by a thickener, sodium carboxymethylcellulose (SCMC), while an anionic surfactant, sodium dodecylbenzene sulfonate (SDBS), was used to control the surface tension of groundwater. When resident DI water was displaced with a SCMC solution (500 mg/L), a SDBS solution (200 mg/L), and a solution with both SCMC (500 mg/L) and SDBS (200 mg/L), the air saturation for sand-packed columns achieved by air sparging increased by 9.5%, 128%, and 154%, respectively, (compared to that of the DI water-saturated column). When the resident water contained SCMC, the minimum air pressure necessary for air sparging processes increased, which is considered to be responsible for the increased air saturation. The extent of the sparging influence zone achieved during the air sparging process using the 2-D model was also affected by viscosity control. Larger sparging influence zones (de-saturated zone due to air injection) were observed for the air sparging processes using the 2-D model initially saturated with high-viscosity solutions, than those without a thickener in the aqueous solution. The enhanced air saturations using SCMC for the 1-D air sparging experiment improved the degradative performance of gaseous oxidation agent (ozone) during air sparging, as measured by the disappearance of fluorescence (fluorescein sodium salt). Based on the experimental evidence generated in this study, the addition of a thickener in the aqueous solution prior to air sparging increased the degree of air saturation and the sparging influence zone, and enhanced the remedial potential of SEAS for contaminated aquifers. Copyright © 2018 Elsevier B.V. All rights reserved.

Emerging poly- and perfluoroalkyl substances in the aquatic environment: A review of current literature.

PubMed

Xiao, Feng

2017-11-01

Poly- and perfluoroalkyl substances (PFASs) comprise a group of synthetic organic surfactants with a wide range of industrial and commercial applications. A few PFASs such as perfluorooctane sulfonate (PFOS) and perfluorooctanoate (PFOA) are now known to be ubiquitously present in the aquatic environment. They have become a global concern because of the toxicity and bioaccumulative properties. With the increasing availability of high-resolution mass spectrometers, many novel PFASs have been identified. Studies published between 2009 and 2017 have discovered 455 new PFASs (including nine fully and 446 partially fluorinated compounds), 45%, 29%, 17%, and 8% of which are anions, zwitterions, cations, and neutrals, respectively. They have been identified in natural waters, fish, sediments, wastewater, activated sludge, soils, aqueous film-forming foams, and commercial fluoropolymer surfactants. This article integrates and critically evaluates what is known about these newly identified PFASs. It discusses the different aspects of detection methodologies. It also surveys the removal of these compounds during conventional and advanced drinking-water and wastewater treatment, predicts the relevant physicochemical properties by means of four software programs, and identifies major knowledge gaps. Notably, a number of these newly identified PFASs are potential precursor compounds of PFOS and PFOA. Studies are critically needed to understand the removal and transformation of these compounds in natural and engineered environmental systems and their contribution, if any, to the secondary formation of PFOS and PFOA in these systems. Copyright © 2017 Elsevier Ltd. All rights reserved.

Sulfonated poly(ether sulfone)s containing pyridine moiety for PEMFC.

PubMed

Jang, Hohyoun; Islam, Md Monirul; Lim, Youngdon; Hossain, Md Awlad; Cho, Younggil; Joo, Hyunho; Kim, Whangi; Jeon, Heung-Seok

2014-10-01

Sulfonated poly(ether sulfone)s with varied degree of sulfonation (DS) were prepared via post-sulfonation of synthesized pyridine based poly(ether sulfone) (PPES) using concentrated sulfuric acid as sulfonating agent. The DS was varied with different mole ratio of 4,4'-(2,2-diphenylethenylidene)diphenol, DHTPE in the polymer unit. PPES copolymers were synthesized by direct polycondensation of pyridine unit with bis-(4-fluorophenyl)-sulfone, 4, 4'-sulfonyldiphenol and DHTPE. The structure of the resulting PPES copolymer membranes with different sulfonated units were studied by 1H NMR spectroscopy and thermogravimetric analysis (TGA). Sorption experiments were conducted to observe the interaction of sulfonated polymer with water. The ion exchange capacity (IEC) and proton conductivity were evaluated according to the increase of DS. The water uptake (WU) of the resulting membranes was in the range of 17-58%, compared to that of Nafion 211 28%. The membranes provided proton conductivities of 65-95 mS/cm in contrast to 103 mS/cm of Nafion 211.

Preparation and characterization of highly water-soluble magnetic Fe3O4 nanoparticles via surface double-layered self-assembly method of sodium alpha-olefin sulfonate

NASA Astrophysics Data System (ADS)

Li, Honghong; Qin, Li; Feng, Ying; Hu, Lihua; Zhou, Chunhua

2015-06-01

A kind of double-layered self-assembly sodium alpha-olefin sulfonate (AOS) capped Fe3O4 magnetic nanoparticles (Fe3O4-AOS-MN) with highly water-solubility was prepared by a wet co-precipitation method with a pH of 4.8. The resulting Fe3O4-AOS-MN could be dispersed into water to form stable magnetic fluid without other treatments. The result of X-ray diffraction (XRD) indicated that the Fe3O4-AOS-MN maintained original crystalline structure and exhibited a diameter of about 7.5 nm. The iron oxide phase of nanoparticles determined by Raman spectroscopy is Fe3O4. Transmission electron microscopy (TEM) analysis confirmed that the Fe3O4-AOS-MN with spherical morphology were uniformly dispersed in water. FT-IR spectroscopy (FT-IR) and thermo-gravimetric analysis (TGA) verified the successful preparation of Fe3O4-AOS-MN capped with double-layered self-assembled AOS. The corresponding capacities of monolayer chemical absorption and the second-layer self-assembly absorption were respectively 4.07 and 14.71 wt% of Fe3O4-MN, which were much lower than those of other surfactants. Vibrating sample magnetometer (VSM) test result showed Fe3O4-AOS-MN possessed superparamagnetic behavior with the saturation magnetization value of about 44.45 emu/g. The blocking temperature TB of Fe3O4-AOS-MN capped with double-layered AOS is 170 K.

Acute and chronic effects of perfluorobutane sulfonate (PFBS) on the mallard and northern bobwhite quail.

PubMed

Newsted, J L; Beach, Susan A; Gallagher, S P; Giesy, J P

2008-04-01

Perfluorobutane sulfonate (PFBS) can be a final degradation product of perfluorobutane sulfonyl fluoride (PBSF)-based chemicals. Surfactants based on this chemistry are potential replacements for perfluorooctane sulfonate (PFOS)-related products and have many potential applications in industrial and commercial processes and applications. To evaluate the potential hazard that PFBS may pose to avian species, acute dietary studies with juvenile mallards and northern bobwhite quail, as well as a quail dietary chronic study of reproduction were conducted. In the acute studies, 10-day-old mallards and quail were exposed to nominal dietary concentrations of 1,000, 1,780, 3,160, 5,620 or 10,000 mg PFBS/kg feed, wet weight (ww) for 5 days and the birds were then fed an untreated diet and observed for up to 17 days. No treatment-related mortalities were observed in the study up to 10,000 mg PFBS/kg, ww feed. Body weight gains of quail exposed to 5620 or 10,000 mg PFBS/kg feed were statistically less than that of unexposed controls. Weight gain of mallards exposed to 10,000 mg PFBS/kg feed was statistically less than that of controls. There were no statistically significant effects on feed consumption of either species. In the acute studies, no observed adverse effect concentration (NOAEC) for mallards and quail were 5620 and 3160 mg PFBS/kg, ww feed, respectively. In a reproduction study, adult quail were exposed to nominal dietary concentrations of 100, 300, or 900 mg PFBS/kg, ww feed for up to 21 weeks. There were no treatment-related mortalities or effects on body weight, weight gain, feed consumption, histopathology measures, or reproductive parameters evaluated in the study when compared to the control group. Concentrations of PFBS in blood serum, liver, and eggs were dose-dependent but were less than the administered dose, indicating biodiminution. Based on the results from the quail reproduction study, the dietary NOAEC was 900 mg PFBS/kg, ww feed (equivalent to an ADI of 87.8 mg PFBS/kg bw/d).

NDELA and nickel modulation of triazine disposition in skin.

PubMed

Baynes, Ronald E; Brooks, James D; Barlow, Beth M; Riviere, Jim E

2005-10-01

Cutting fluids can become contaminated with metals (e.g., nickel, Ni) and nitrosamines (e.g., N-nitrosodiethanolamine, NDELA) and there is concern that these classes of contaminants can modulate dermal disposition and ultimately the toxicity of cutting fluid additives, such as irritant biocides (e.g., triazine). Biocides are added to these formulations to prevent bacterial degradation of commercial cutting fluids. The purpose of this study was to assess the dermal absorption and skin deposition of 14C-triazine when topically applied to porcine skin in an in vitro flow-through diffusion cell system as aqueous soluble oil (mineral oil, MO) or aqueous synthetic (polyethylene glycol, PEG) mixtures. 14C-Triazine mixtures were formulated with NDELA and/or Ni, or with a combination of three additional cutting fluid additives; namely, 5% linear alkylbenzene sulfonate (LAS), 5% triethanolamine (TEA) and 5% sulfurized ricinoleic acid. Neither Ni nor NDELA was absorbed during these 8-h studies. However, 14C-triazine absorption ranged from 2.72 to 3.29% dose in MO and 2.29-2.88% dose in PEG with significantly greater triazine absorption in MO than PEG when all additives and contaminates were present. The difference between these two diluents was most pronounced when NDELA and/or Ni were present in cutting fluids. These contaminants also enhanced triazine deposition on the skin surface and skin tissues especially with PEG-based mixtures. In essence, the dermal disposition of irritant biocides could be dependent on whether the worker is exposed to a soluble oil or synthetic fluid when these contaminants are present. Workers should therefore not only be concerned about dermatotoxicity of these contaminants, but also the modulated dermal disposition of cutting fluid additives when these contaminants are present in cutting fluid formulations.

Field evidence for a protistan role in an organically-contaminated aquifer

USGS Publications Warehouse

Kinner, Nancy E.; Harvey, Ronald W.; Shay, David M.; Metge, David W.; Warren, Alan

2002-01-01

The association between protists, bacteria, and dissolved organic carbon (DOC) in an oxygen-depleted, 6 km-long wastewater contaminant plume within a sandy aquifer (Cape Cod, MA) was investigated by comparing abundance patterns along longitudinal and vertical transects and at a control site. Strong linear correlations were observed between unattached bacterial abundance and DOC for much of the upgradient-half of the plume (0.1−2.5 km downgradient from the source) that is characterized by quasi-steady state chemistry. However, a logarithmic decrease was observed between the number of protists supported per mg of DOC and the estimated age of the DOC within the plume. The relatively labile dissolved organic contaminants that characterize the groundwater sampled from the plume ≤0.1 km downgradient from the contaminant source appeared to indirectly support 3−4 times as many protists (per mg of DOC) as the older, more recalcitrant DOC in the alkylbenzene sulfonate (ABS)-contaminated zone at 3 km downgradient (∼30 years travel time). Substantive numbers of protists (>104/cm3) were recovered from suboxic zones of the plume. The higher than expected ratios of protists to unattached bacteria (10 to 100:1) observed in much of the plume suggest that protists may be grazing upon both surface-associated and unattached bacterial communities to meet their nutritional requirements. In closed bottle incubation experiments, the presence of protists caused an increase in bacterial growth rate, which became more apparent at higher amendments of labile DOC (3−20 mgC/L). The presence of protists resulted in an increase in the apparent substrate saturation level for the unattached bacterial community, suggesting an important role for protists in the fate of more-labile aquifer organic contaminants.

Molecular characterization of dissolved organic matter in contrasted freshwater environments by electrospray ionization mass spectrometry and EEM-PARAFAC

NASA Astrophysics Data System (ADS)

Parot, Jérémie; Parlanti, Edith; Guéguen, Céline

2015-04-01

Dissolved organic matter (DOM) is a key parameter in the fate, transport and mobility of inorganic and organic pollutants in natural waters. Excitation emission matrix (EEM) spectra coupled to parallel factor analysis (PARAFAC) provide insights on the main fluorescent DOM constituents. However, the molecular structures associated with PARAFAC DOM remain poorly understood. In this study, DOM from rivers, marshes and algal culture was characterized by EEM-PARAFAC and electrospray ionization Fourier transform mass spectrometry (ESI-FT-MS, Orbitrap Q Exactive). The high resolution of the Orbitrap (i.e. 140,000) allowed us to separate unique molecular species from the complex DOM mixtures. The majority of chemical species were found within the mass to charge ratio (m/z) 200 to 400. Weighted averages of neutral mass were 271.254, 236.480, 213.992Da for river, marsh and algal-derived DOM, respectively, congruent with previous studies. The assigned formula were dominated by CHO in humic-rich river waters whereas N- and S-containing compounds were predominant in marsh and algal samples. Marsh consisted of N and S-containing compounds, which were presumed to be linear alkylbenzene sulfonates. And the double bond equivalent (DBE) was higher in the marsh and in comparison was lower in the algal culture. Kendrick masses, used to identify homologous compounds differing only by a number of base units in high resolution mass spectra, and Van Krevelen diagrams, plot of molar ratio of hydrogen to carbon (H/C) versus oxygen to carbon (O/C), will be discussed in relation to PARAFAC components to further discriminate freshwater systems based on the origin and maturity of DOM. Together, these results showed that ESI-FT-MS has a great potential to distinguish freshwater DOM at the molecular level without any fractionation.

Synthesis and analytical follow-up of the mineralization of a new fluorosurfactant prototype.

PubMed

Peschka, M; Fichtner, N; Hierse, W; Kirsch, P; Montenegro, E; Seidel, M; Wilken, R D; Knepper, T P

2008-08-01

Fluorinated surfactants have become essential in numerous technical applications due to their unparalleled effectiveness and efficiency. The environmental persistence of the non-biodegradable perfluorinated alkyl moiety has become a matter of concern. Therefore, it was searched for new molecules with chemically stable fluorinated end groups which can be microbially transformed into labile fluorinated substances. One prototype substance, 10-(trifluoromethoxy)decane-1-sulfonate, has shown biomineralization. Monitoring the formation of metabolites over time elucidated the mechanism of biotransformation. Analysis was performed utilizing liquid chromatography-single quadrupole mass spectrometry (LC-MS) and quadrupole-time of flight tandem mass spectrometry (QqTOF-MS). It was possible to distinguish between two major degradation pathways of the fluorinated alkylsulfonate derivative: (i) a desulfonation and subsequent oxidation and degradation of the alkyl chain being predominant and (ii) an insertion of oxygen with a subsequent cleavage and degradation of the molecule. The utilized trifluoromethoxy-endgroup resulted in instable trifluoromethanol after degradation of the alkyl chain, which led to a high degree of mineralization of the molecule.

Analysis of emulsion stability in acrylic dispersions

NASA Astrophysics Data System (ADS)

Ahuja, Suresh

2012-02-01

Emulsions either micro or nano permit transport or solubilization of hydrophobic substances within a water-based phase. Different methods have been introduced at laboratory and industrial scales: mechanical stirring, high-pressure homogenization, or ultrasonics. In digital imaging, toners may be formed by aggregating a colorant with a latex polymer formed by batch or semi-continuous emulsion polymerization. Latex emulsions are prepared by making a monomer emulsion with monomer like Beta-carboxy ethyl acrylate (β-CEA) and stirring at high speed with an anionic surfactant like branched sodium dodecyl benzene sulfonates , aqueous solution until an emulsion is formed. Initiator for emulsion polymerization is 2-2'- azobis isobutyramide dehydrate with chain transfer agent are used to make the latex. If the latex emulsion is unstable, the resulting latexes produce a toner with larger particle size, broader particle size distribution with relatively higher latex sedimentation, and broader molecular weight distribution. Oswald ripening and coalescence cause droplet size to increase and can result in destabilization of emulsions. Shear thinning and elasticity of emulsions are applied to determine emulsion stability.

Sulfonimide-containing poly(arylene ether)s and poly(arylene ether sulfone)s, methods for producing the same, and uses thereof

DOEpatents

Hofmann, Michael A.

2006-11-14

The present invention is directed to sulfonimide-containing polymers, specifically sulfonimide-containing poly(arylene ether)s and sulfonimide-containing poly(arylene ether sulfone)s, and processes for making the sulfonimide-containing poly(arylene ether)s and sulfonimide-containing poly(arylene ether sulfone)s, for use conductive membranes and fuel cells.

Ipso Nitration. Regiospecific Nitration via Ipso Nitration Products.

DTIC Science & Technology

1985-05-20

products of nitration of alkylbenzenes and alkylphenol derivatives. The general pattern envisioned is shown in Scheme 1. In order to realize this...we have also explored solid state nitration of various alkylphenols . This procedure involves adsorbing concentrated nitric acid on alumina, followed

Simulation study of sulfonate cluster swelling in ionomers

NASA Astrophysics Data System (ADS)

Allahyarov, Elshad; Taylor, Philip L.; Löwen, Hartmut

2009-12-01

We have performed simulations to study how increasing humidity affects the structure of Nafion-like ionomers under conditions of low sulfonate concentration and low humidity. At the onset of membrane hydration, the clusters split into smaller parts. These subsequently swell, but then maintain constant the number of sulfonates per cluster. We find that the distribution of water in low-sulfonate membranes depends strongly on the sulfonate concentration. For a relatively low sulfonate concentration, nearly all the side-chain terminal groups are within cluster formations, and the average water loading per cluster matches the water content of membrane. However, for a relatively higher sulfonate concentration the water-to-sulfonate ratio becomes nonuniform. The clusters become wetter, while the intercluster bridges become drier. We note the formation of unusual shells of water-rich material that surround the sulfonate clusters.

21 CFR 177.2210 - Ethylene polymer, chloro-sulfonated.

Code of Federal Regulations, 2011 CFR

2011-04-01

...) Ethylene polymer, chloro-sulfonated is produced by chloro-sulfonation of a carbon tetrachloride solution of... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Ethylene polymer, chloro-sulfonated. 177.2210... as Components of Articles Intended for Repeated Use § 177.2210 Ethylene polymer, chloro-sulfonated...

21 CFR 172.824 - Sodium mono- and dimethyl naphthalene sulfonates.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Sodium mono- and dimethyl naphthalene sulfonates... sulfonates. The food additive sodium mono- and dimethyl naphthalene sulfonates may be safely used in... statement declaring the presence of sodium mono- and dimethyl naphthalene sulfonates. [42 FR 14491, Mar. 15...

ANAEROBIC BIODEGRADATION OF ALKYLBENZENES IN LABORATORY MICROCOSMS REPRESENTING AMBIENT CONDITIONS

EPA Science Inventory

A microcosm study was performed to document the anaerobic biodegradation of benzene, toluene, ethylbenzene, m- xylene, and/or o-xylene in petroleum-contaminated aquifer sediment from sites in Michigan (MI) and North Carolina (NC) and relate the results to previous field investiga...

SENSORY REACTIONS OF NASAL PUNGENCY AND ODOR TO VOLATILE ORGANIC COMPOUNDS: THE ALKYLBENZENES

EPA Science Inventory

Research assessed the independent contribution of the trigeminal and olfactory nerves to the detection of airborne chemicals by measuring nasal detection thresholds in subjects clinically diagnosed as lacking a functional sense of smell (anosmics) and in matched normal controls (...

On the Extraction of Aromatic Compounds from Hydrocarbons by Imidazolium Ionic Liquids

PubMed Central

Cassol, Cláudia C.; Umpierre, Alexandre P.; Ebeling, Günter; Ferrera, Bauer; Chiaro, Sandra S. X.; Dupont, Jairton

2007-01-01

The liquid-liquid equilibrium for the ternary system formed by n-octane and aromatic (alkylbenzenes) and heteroaromatic compounds (nitrogen and sulfur containing heterocyles) and 1-alkyl-3-methylimidazolium ionic liquids (ILs) associated with various anions has been investigated. The selectivity on the extraction of a specific aromatic compound is influenced by anion volume, hydrogen bond strength between the anion and the imidazolium cation and the length of the 1-methyl-3-alkylimidazolium alkyl side chain. The interaction of alkylbenzenes and sulfur heterocyles with the IL is preferentially through CH-π hydrogen bonds and the quantity of these aromatics in the IL phase decreases with the increase of the steric hindrance imposed by the substituents on the aromatic nucleus. In the case of nitrogen heterocycles the interaction occurs preferentially through N(heteroaromatic)-H(imidazolium) hydrogen bonds and the extraction process is largely controlled by the nitrogen heterocycle pKa. Competitive extraction experiments suggest that benzene, pyridine and dibenzothiophene do not compete for the same hydrogen bond sites of the IL.

Modeling the Conformation-Specific Infrared Spectra of N-Alkylbenzenes

NASA Astrophysics Data System (ADS)

Tabor, Daniel P.; Sibert, Edwin; Hewett, Daniel M.; Korn, Joseph A.; Zwier, Timothy S.

2016-06-01

Conformation-specific UV-IR double resonance spectra are presented for n-alkylbenzenes. With the aid of a local mode Hamiltonian that includes the effects of stretch-bend Fermi coupling, the spectra of ethyl, n-propyl, and n-butylbenzene are assigned to individual conformers. These molecules allow for further development of the work on a first principles method for calculating alkyl stretch spectra. Due to the consistency of the anharmonic couplings from conformer to conformer, construction of the model Hamiltonian for a given conformer only requires a harmonic frequency calculation at the conformer's minimum geometry as an input. The model Hamiltonian can be parameterized with either density functional theory or MP2 electronic structure calculations. The relative strengths and weaknesses of these methods are evaluated, including their predictions of the relative energetics of the conformers. Finally, the IR spectra for conformers that have the alkyl chain bend back and interact with the π cloud of the benzene ring are modeled.

Beyond the Bend: Exploring the Conformational Landscape of Decyl, Undecyl, and Dodecylbenzene

NASA Astrophysics Data System (ADS)

Hewett, Daniel M.; Zwier, Timothy S.

2017-06-01

Alkylbenzenes are important components in the combustion process: they make up 20-30% of petroleum fuels and are intermediates on the pathway to soot formation. Understanding their conformational preferences is a vital step in understanding the processes by which fuels begin their journey from small, simple hydrocarbons into the large, graphitic masses of soot. Previous work done in our group, in collaboration with the Sibert group, found that the smallest alkylbenzene which folds its chain back over the ring is octylbenzene. The population of the lone folded structure in octylbenzene is low; however, theory predicts a rapid stabilization of the folded conformations relative to more extended structures as the chain length is increased, suggesting a likely shift in population towards folded structures. This talk will focus on our exploration of this possibility by discussing the UV excitation and single conformation IR spectra of decyl, undecyl, and dodecylbenzene, where increasing chain length allows for multiple stable folded configurations.

Process for conversion of lignin to reformulated, partially oxygenated gasoline

DOEpatents

Shabtai, Joseph S.; Zmierczak, Wlodzimierz W.; Chornet, Esteban

2001-01-09

A high-yield process for converting lignin into reformulated, partially oxygenated gasoline compositions of high quality is provided. The process is a two-stage catalytic reaction process that produces a reformulated, partially oxygenated gasoline product with a controlled amount of aromatics. In the first stage of the process, a lignin feed material is subjected to a base-catalyzed depolymerization reaction, followed by a selective hydrocracking reaction which utilizes a superacid catalyst to produce a high oxygen-content depolymerized lignin product mainly composed of alkylated phenols, alkylated alkoxyphenols, and alkylbenzenes. In the second stage of the process, the depolymerized lignin product is subjected to an exhaustive etherification reaction, optionally followed by a partial ring hydrogenation reaction, to produce a reformulated, partially oxygenated/etherified gasoline product, which includes a mixture of substituted phenyl/methyl ethers, cycloalkyl methyl ethers, C.sub.7 -C.sub.10 alkylbenzenes, C.sub.6 -C.sub.10 branched and multibranched paraffins, and alkylated and polyalkylated cycloalkanes.

Long-Term Fate of Organic Micropollutants in Sewage-Contaminated Groundwater

USGS Publications Warehouse

Barber, L.B.; Schroeder, M.P.; LeBlanc, D.R.

1988-01-01

Disposal of secondary sewage effluent by rapid infiltration has produced a plume of contaminated groundwater over 3500 m long near Falmouth, MA. Approximately 50 volatile organic compounds were detected and identified in the plume, at concentrations ranging from 10 ng/L to 500 ??g/L, by closed-loop stripping and purge- and-trap in conjuction with gas chromatography-mass spectrometry. The dominant contaminants were di-, tri- and tetrachloroethene, o- and p-dichlorobenzene, C1 to C6 alkylbenzenes, 2,6-di-tert-butylbenzoquinone, and several isomers of p-nonylphenol. The chloroethenes and chlorobenzenes had the same general distribution as chloride and boron and appear to be transported with little retardation. Less soluble compounds, such as nonylphenol and di-tert-butylbenzoquinone, appear to be retarded during subsurface transport by sorption processes. Although biodegradation of labile organic compounds occurs near the infiltration beds, many trace compounds, including chlorinated benzenes, alkylbenzenes, and aliphatic hydrocarbons, have persisted for more than 30 years in the aquifer.

Occurrence survey and spatial distribution of perfluoroalkyl and polyfluoroalkyl surfactants in groundwater, surface water, and sediments from tropical environments.

PubMed

Munoz, Gabriel; Labadie, Pierre; Botta, Fabrizio; Lestremau, François; Lopez, Benjamin; Geneste, Emmanuel; Pardon, Patrick; Dévier, Marie-Hélène; Budzinski, Hélène

2017-12-31

The occurrence and spatial distribution of 22 selected perfluoroalkyl and polyfluoroalkyl substances (PFASs) in surface water (n=75), groundwater (n=80) and surficial sediment (n=15) were investigated for the first time in the tropical areas constituted by the French Overseas Territories (French Guiana, Guadeloupe, Martinique, Mayotte and Reunion). Descriptive statistics and correlations between PFASs were evaluated through the use of specific statistical treatments to handle left-censored data ("non-detects"). PFASs were ubiquitous in these samples and detection frequencies as high as 79% for perfluorooctane sulfonate (PFOS) and 65% for perfluorooctanoate (PFOA) were reported in surface waters. ∑PFASs was in the range

Chlorine resistant desalination membranes based on directly sulfonated poly(arylene ether sulfone) copolymers

DOEpatents

McGrath, James E [Blacksburg, VA; Park, Ho Bum [Austin, TX; Freeman, Benny D [Austin, TX

2011-10-04

The present invention provides a membrane, kit, and method of making a hydrophilic-hydrophobic random copolymer membrane. The hydrophilic-hydrophobic random copolymer membrane includes a hydrophilic-hydrophobic random copolymer. The hydrophilic-hydrophobic random copolymer includes one or more hydrophilic monomers having a sulfonated polyarylsulfone monomer and a second monomer and one or more hydrophobic monomers having a non-sulfonated third monomer and a fourth monomer. The sulfonated polyarylsulfone monomer introduces a sulfonate into the hydrophilic-hydrophobic random copolymer prior to polymerization.

HOT ELUENT CAPILLARY LIQUID CHROMATOGRAPHY USING ZIRCONIA AND TITANIA BASED STATIONARY PHASES. (R825344)

EPA Science Inventory

Abstract

High speed capillary liquid chromatographic separations using a simple home made system constructed from readily available inexpensive components have been studied. Using thermally stable zirconia and titania based packing, the separation of eight alkylbenzene...

Biodegradation of fluorinated alkyl substances.

PubMed

Frömel, Tobias; Knepper, Thomas P

2010-01-01

The incorporation of fluorine into organic molecules entails both positive and adverse effects. Although fluorine imparts positive and unique properties such as water-and oil-repellency and chemical stability, adverse effects often pervade members of this compound class. A striking property of long perfluoroalkyl chains is their very pronounced environmental persistence. The present review is the first one designed to summarize recent accomplishments in the field of biodegradation of fluorine-containing surfactants, their metabolites, and structural analogs. The pronounced scientific and public interest in these chemicals has given impetus to undertake numerous degradation studies to assess the sources and origins of different fluorinated analog chemical known to exist in the environment. It was shown that biodegradation plays an important role in understanding how fluorinated substances reach the environment and, once they do, what their fate is. Today, PFOS and PFOA are ubiquitously detected as environmental contaminants. Their prominence as contaminants is mainly due to their extreme persistence, which is linked to their perfluoroalkyl chain length. It appears that desulfonation of a highly fluorinated surfactants can be achieved if an α-situated H atom, in relation to the sulfonate group, is present, at least under sulfur-limiting conditions. Molecules that are less heavily fluorinated can show very complex metabolic behavior, as is the case for fluorotelomer alcohols. These compounds are degraded via different but simultaneous pathways, which produce different stable metabolites, one of which is the respective perfluoroalkanoate (8:2-FTOH is transformed to PFOA). Preliminary screening tests indicate that fluorinated functional groups, such as the trifluoromethoxy group and the p-(trifluoromethyl)phenoxy group, may be useful implementations in novel, environmentally benign fluorosurfactants. More specifically, trifluoromethoxy groups constitute a substitute for those that have been used in the past; this functionality is degradable when it appears in structures that are normally subject to biodegradation. Other compounds tested did not meet this criterion. Interdisciplinary investigations on fluorinated surfactants are still very much needed and will certainly continue during the next many years. For instance, the role of fluorinated polymers in contributing small fluorinated molecules to the environmental burden still has not been fully understood.

A fluorescent molecular sensor for pH windows in traditional and polymeric biocompatible micelles: comicellization of anionic species to shift and reshape the ON window.

PubMed

Cavallaro, Gennara; Giammona, Gaetano; Pasotti, Luca; Pallavicini, Piersandro

2011-09-12

A new approach is presented to obtain fluorescent sensors for pH windows that work in water and under biomimetic conditions. A single molecule that features all-covalently linked components is used, thus making it capable of working as a fluorescent sensor with an OFF/ON/OFF response to pH value. The components are a tertiary amine, a pyridine, and a fluorophore (pyrene). The forms with both protonated bases or both neutral bases quench the pyrene fluorescence, whereas the form with the neutral pyridine and protonated amine groups is fluorescent. The molecular sensor is also equipped with a long alkyl chain to make it highly hydrophobic in all its protonated and unprotonated forms, that is, either when neutral or charged. Accordingly, it can be confined at any pH value either in traditional (i.e., low-molecular-weight) nonionic surfactant micelles or inside polymeric, biocompatible micellar containers. Relevant for future applications in vivo, thanks to its strong hydrophobicity, no leakage of the molecular sensor is observed from the polymeric biocompatible micelles. Due to the proximity of the pyridine and amine functions in the molecular structure and the poor hydration inside the micelles, the observed pK(a) values are low so that the ON window is positioned at very low pH values. However, the window can be shifted to biologically relevant values by comicellization of anionic species. In particular, in the micelles of the nonionic surfactant TritonX-100, a shift of the ON window to pH 4-6 is obtained by addition of the anionic sodium dodecyl sulphate surfactant, whose negative charge promotes the stability of the protonated forms of the pyridine and amine fragments. In the case of the polymeric micelles, we introduce the use of the amphiphilic polystyrene sulfonate anionic polyelectrolyte, the comicellization of which induces a shift and sharpening of the ON window that is centered at pH 4. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Anhydrous state proton and lithium ion conducting solid polymer electrolytes based on sulfonated bisphenol-A-poly(arylene ethers)

NASA Astrophysics Data System (ADS)

Guha Thakurta, Soma

Sulfonated polymer based solid polymer electrolytes (SPEs) have received considerable interest in recent years because of their wide variety of applications particularly in fuel cells, batteries, supercapacitors, and electrochromic devices. The present research was focused on three interrelated subtopics. First, two different bisphenol-A-poly(arylene ethers), polyetherimide (PEI) and polysulfone (PSU) were sulfonated by a post sulfonation method to various degrees of sulfonation, and their thermal and mechanical properties were examined. The effects of poly(arylene ether) chemical structure, reaction time, concentration, and types of sulfonating agents on sulfonation reaction were investigated. It was found that deactivation of bisphenol A unit caused by the electron withdrawing imide, retarded the sulfonation of PEI compared to PSU. Sulfonation conducted with a high concentration of sulfonating agent and/or prolonged reaction time exhibited evidence of degradation at the isopropylidene unit. The degradation occurred through the same mechanistic pathway with the two different sulfonating agents, chlorosulfonic acid (CSA) and trimethylsilyl chlorosulfonate (TMSCS). The degradation was faster with CSA than its silyl ester, TMSCS, and was evident even at low acid concentration. Second, novel anhydrous proton conducting solid polymer electrolytes (SPEs) were prepared by the incorporation of 1H-1,2,4-triazole (Taz) as a proton solvent in sulfonated polyetherimide (SPEI) matrix. The size, shape, and state of dispersion (crystal morphology) of triazole crystals in SPEI were examined as a function of degree of sulfonation and triazole concentration. Increasing sulfonic acid content caused reduction of triazole crystallite size, hence the depression of melting temperature and their uniform distribution throughout the sulfonated polymer matrix. The increased rate of structure diffusion within the smaller size crystals due to the improved molecular mobility contributed significantly to the anhydrous state proton conductivity. Third, a new category of single lithium ion conducting SPEs was developed by crosslinking a polyether epoxy, poly(ethylene glycol)diglicidyl ether (PEGDGE) (lithium ion solvent), in sulfonated polysulfone (SPSU) matrix. The effects of degree of sulfonation and electrolyte composition on ionic conductivity, thermal, and tensile properties of SPEs were investigated. It was found that ion-dipole interactions between lithium sulfonate (SO3Li) and PEGDGE were responsible for the reduction in size of the dispersed epoxy phase and increased thermal stability. Lithium sulfonate promoted compatibilization and also caused improvement in elongation at break. A low molecular weight electrolyte salt, lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) was further dissolved in PEGDGE phase prior to its crosslinking in SPSU matrix, and the ionic conductivity and thermal properties were evaluated as a function of doping level. The ionic conductivity showed remarkable improvement compared to the undoped system.

Surface treated carbon catalysts produced from waste tires for fatty acids to biofuel conversion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hood, Zachary D.; Adhikari, Shiba P.; Wright, Marcus W.

A method of making solid acid catalysts includes the step of sulfonating waste tire pieces in a first sulfonation step. The sulfonated waste tire pieces are pyrolyzed to produce carbon composite pieces having a pore size less than 10 nm. The carbon composite pieces are then ground to produce carbon composite powders having a size less than 50 .mu.m. The carbon composite particles are sulfonated in a second sulfonation step to produce sulfonated solid acid catalysts. A method of making biofuels and solid acid catalysts are also disclosed.

BIODEGRADATION OF MONOAROMATIC HYDROCARBONS BY AQUIFER MICROORGANISMS USING OXYGEN, NITRATE, OR NITROUS OXIDE AS THE TERMINAL ELECTRON ACCEPTOR

EPA Science Inventory

Microcosms were prepared from aquifer material, spiked with monoaromatic hydrocarbons, and amended with oxygen, nitrate, and nitrous oxide. Benzene and alkylbenzenes were degraded to concentrations below 5 µg/liter within 7 days under aerobic conditions, whereas only the alkylbe...

Projections of Demand for Waterborne Transportation, Ohio River Basin, 1980, 1990, 2000, 2020, 2040. Volume 8. Group VI. Chemicals & Chemical Fertilizers.

DTIC Science & Technology

1980-12-01

medicinal chemicals, botanical products and pharmaceutical pre- parat ions) -3- 2841 Soap, detergents, and cleaning preparation; perfumes , cos- metics...dcecylbenzene Higher alkylbenzenes, nec. Cyclohexane Toluene DII socyanates Phthalic acid and anhydrides Dimethyl terephthalate Ethylbenzene Tetrahydrofuran

STIMULATION OF THE REDUCTIVE DECHLORINATION OF TETRACHLOROETHENE IN ANAEROBIC AQUIFER MICROCOSMS BY THE ADDITION OF TOLUENE

EPA Science Inventory

In this study, the biologically mediated interactions of toluene and PCE under anaerobic conditions were investigated by using microcosms constructed with aquifer solids from an area that was exposed to both alkylbenzenes and chlorinated ethenes at the U.S. Coast Guard Air Statio...

ASSESSMENT OF THE MICROBIAL POTENTIAL FOR NITRATE- ENHANCED BIOREMEDIATION OF A JP-4 FUEL-CONTAMINATED AQUIFER

EPA Science Inventory

A site that was contaminated with JP-4 jet fuel was characterized microbiologically to assess the feasibility of nitrate-enhanced bioremediation. The results of microcosm studies indicated that the mean pseudo zero-order rate constants for alkylbenzene biodegradation and NO3^...

Materials for use as proton conducting membranes for fuel cells

DOEpatents

Einsla, Brian R [Blacksburg, VA; McGrath, James E [Blacksburg, VA

2009-01-06

A family of polymers having pendent sulfonate moieties connected to polymeric main chain phenyl groups are described. These polymers are prepared by the steps of polymerization (using a monomer with a phenyl with an alkoxy substitution), deportation by converting the alkoxy to a hydroxyl, and functionalization of the polymer with a pendant sulfonate group. As an example, sulfonated poly(arylene ether sulfone) copolymers with pendent sulfonic acid groups are synthesized by the direct copolymerization of methoxy-containing poly(arylene ether sulfone)s, then converting the methoxy groups to the reactive hydroxyl form, and finally functionalizing the hydroxyl form with proton-conducting sites through nucleophilic substitution. The family of polymers may have application in proton exchange membranes and in other applications.

The effects of perfluorinated chemicals on adipocyte differentiation in vitro.

PubMed

Watkins, Andrew M; Wood, Carmen R; Lin, Mimi T; Abbott, Barbara D

2015-01-15

The 3T3-L1 preadipocyte culture system has been used to examine numerous compounds that influence adipocyte differentiation or function. The perfluoroalkyl acids (PFAAs), used as surfactants in a variety of industrial applications, are of concern as environmental contaminants that are detected worldwide in human serum and animal tissues. This study was designed to evaluate the potential for PFAAs to affect adipocyte differentiation and lipid accumulation using mouse 3T3-L1 cells. Cells were treated with perfluorooctanoic acid (PFOA) (5-100 µM), perfluorononanoic acid (PFNA) (5-100 µM), perfluorooctane sulfonate (PFOS) (50-300 µM), perfluorohexane sulfonate (PFHxS) (40-250 µM), the peroxisome proliferator activated receptor (PPAR) PPARα agonist Wyeth-14,643 (WY-14,643), and the PPARγ agonist rosiglitazone. The PPARγ agonist was included as a positive control as this pathway is critical to adipocyte differentiation. The PPARα agonist was included as the PFAA compounds are known activators of this pathway. Cells were assessed morphometrically and biochemically for number, size, and lipid content. RNA was extracted for qPCR analysis of 13 genes selected for their importance in adipocyte differentiation and lipid metabolism. There was a significant concentration-related increase in cell number and decreased cell size after exposure to PFOA, PFHxS, PFOS, and PFNA. All four PFAA treatments produced a concentration-related decrease in the calculated average area occupied by lipid per cell. However, total triglyceride levels per well increased with a concentration-related trend for all compounds, likely due to the increased cell number. Expression of mRNA for the selected genes was affected by all exposures and the specific impacts depended on the particular compound and concentration. Acox1 and Gapdh were upregulated by all six compounds. The strongest overall effect was a nearly 10-fold induction of Scd1 by PFHxS. The sulfonated PFAAs produced numerous, strong changes in gene expression similar to the effects after treatment with the PPARγ agonist rosiglitazone. By comparison, the effects on gene expression were muted for the carboxylated PFAAs and for the PPARα agonist WY-14,643. In summary, all perfluorinated compounds increased cell number, decreased cell size, increased total triglyceride, and altered expression of genes associated with adipocyte differentiation and lipid metabolism. Published by Elsevier Ireland Ltd.

Synthesis and fabrication of sized-controlled nanoparticles: Using surface self-assemblies as building blocks for developing supralattices on nanocomposite materials

NASA Astrophysics Data System (ADS)

Yee, Chanel Kitmon

2001-10-01

A general one-phase synthesis for self-assembling thiols onto gold, platinum, palladium and iridium nanoparticles using tetrahydrofuran (THF) as the solvent, and lithium triethylborohydride (superhydride) as the reducing agent, is presented. Using the same synthetic procedure gold nanoparticles functionalized with 11-hydroxyundecane-1-thiol and 4'-bromo-4-mercaptobiphenyl were prepared to show that the availability and reflexibility of this method could lead to surface fabrication with various type of facial moieties. Alkyl selenide- and alkyl thiolate-functionalized gold nanoparticles were also prepared by the same method at 6°C. The properties were compared to their counterparts made at 25°C. The formation of the Se-Au bond and S-Au bonds was investigated by transmission Fourier transform infrared spectroscopy (FTIR), while the bond nature in each case was examined by x-ray photoelectron spectroscopy (XPS). Particle size was determined by Transmission Electron Microscopy (TEM), and further confirmed by ultraviolet spectroscopy (UV). Superparamagnetic Fe and Fe2O3 nanoparticles were synthesized by ultrasound irradiation and post-fabricated with alkyl sulfonic acids of various chain lengths and octadecyl phosphonic acid. TEM reveals nanoparticles of 5--10 mn in diameter. FTIR spectra suggest that the alkyl chains are packed in a solid-like assembly with packing disorder increasing with the decreasing chain length. The octadecyl sulfonic acid coating displays the lowest magnetization within the sulfonic acid series, which may be explained by the high packing and ordering of the alkyl chains on the particle surface. The smallest value of magnetization in the OPA case suggests that the spin-state of surface Fe3+ ions is affected by the bonded surfactant, and that the phosphonate empty d-orbitals increase magnetic interactions between neighboring Fe3+ spins. To build superstructures beyond the monolayer level, a general route for the attachment of amino-terminated biomolecules to nanoparticles was proposed. Thiophene thiolate-functionalized platinum nanoparticles were prepared and reacted with nitrosonium tetrafluoroborate to provide the nitroso-functionalized nanoparticles. The reaction of the nitroso group with primary amines to yield strong N=N bonds might provide a general route for the attachment of amino-terminated biomolecules to nanoparticles. The attachment of two cytidine molecules to platinum nanoparticles was accomplished, and experimental data were provided to demonstrate the intended grafting reaction.

[Synthesis, solubility, lipids-lowering and liver-protection activities of sulfonated formononetin].

PubMed

Wang, Qiu-ya; Meng, Qing-hua; Zhang, Zun-ting; Tian, Zhen-jun; Liu, Hui

2009-04-01

A water-soluble compound, sodium formononetin-3'-sulfonate with good lipid-lowering and liver-protection activities was synthesized. It was synthesized by sulfonation reaction, and its structure was characterized by IR, NMR and elemental analyses. The solubility of sodium formononetin-3'-sulfonate in water and n-octanol/water partition coefficient were determined by UV spectrophotometry. The lipid-lowering and liver-protection activities of sodium formononetin-3'-sulfonate were tested by using rat's high fat model induce by feeding with high fat food. The results showed that sodium formononetin-3'-sulfonate not only had favorable water, solubility but also had good lipid-lowering and liver-protection activities.

Smartphone app-based/portable sensor for the detection of fluoro-surfactant PFOA.

PubMed

Fang, Cheng; Zhang, Xian; Dong, Zhaomin; Wang, Liang; Megharaj, Mallavarapu; Naidu, Ravi

2018-01-01

We developed a smartphone app-based monitoring tool for the detection of anionic surfactants (AS), including perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS). Akin to the methylene blue active substances (MBAS), liquid-phase extraction (LPE) is employed to extract the hydrophobic ion-pair of dye (ethyl violet)-AS to an organic phase (ethyl acetate). The colour (RGB) of the organic phase is read using a smartphone camera with the help of a reading kit. The value of RGB is carefully corrected and linked to the concentration of ASs with a standard deviation of <10% in the 10-1000 ppb (part per billion) range. In order to avoid the interference arising from inorganic anions (such as those found in tap water and groundwater), the water sample is pre-treated either by solid-phase extraction (SPE), which takes ∼30 min, or by dual liquid-phase extraction (dual-LPE, developed by us), which takes ∼5 min. In the latter case, the organic phase of the first LPE (equilibrium with water sample) is transferred and subjected to a second LPE (equilibrium with Milli-Q water) to remove any potential background interference. In the meantime, SPE can also pre-concentrate ASs at 100-1000 times (in volume) to benefit the sensitivity. Consequently, our smartphone app can detect PFOA spiked in tap/groundwater with an LOD of 10 ppb (∼12 nM, dual-LPE of ∼5 min), or 0.5 ppb (∼1.2 nM, SPE of ∼3 h), suggesting that it has the potential to succeed as a pre-screening tool for on-site application and in common laboratory tests. Copyright © 2017 Elsevier Ltd. All rights reserved.

Synthesis and characterization of sulfonated poly ether ether ketone (sPEEK) membranes for low temperature fuel cells

NASA Astrophysics Data System (ADS)

Ali, Mawlood Maajal; Rizvi, S. J. A.; Azam, Ameer

2018-05-01

Poly ether ether ketone (PEEK) was sulfonated with 1.0 M sulphuric acid for varying durations to have various degrees of sulfonation (DS) from 43 to 55%. The FT-IR spectra confirmed the successful sulfonation of PEEK. The sulfonated PEEK (sPEEK) membranes were prepared by a solvent casting method using dimethylacetamide (DMAc) as solvent and upon drying the membranes were characterized. The DS% and ion exchange capacity (IEC) were determined by a back titration method. The IEC and DS of sPEEK was found to increase with the increment of sulfonation reaction time. Water uptake also increased with increase in the DS. The Thermogravimetric (TGA) curves revealed poor thermal stability of sPEEK. The proton conductivity of sPEEK membrane was found to considerably better with degree of sulfonation for fuel cell application.

Bisphenol A sulfonation is impaired in metabolic and liver disease

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yalcin, Emine B.; Kulkarni, Supriya R.; Slitt, Angela L., E-mail: angela_slitt@uri.edu

Background: Bisphenol A (BPA) is a widely used industrial chemical and suspected endocrine disruptor to which humans are ubiquitously exposed. The liver metabolizes and facilitates BPA excretion through glucuronidation and sulfonation. The sulfotransferase enzymes contributing to BPA sulfonation (detected in human and rodents) is poorly understood. Objectives: To determine the impact of metabolic and liver disease on BPA sulfonation in human and mouse livers. Methods: The capacity for BPA sulfonation was determined in human liver samples that were categorized into different stages of metabolic and liver disease (including obesity, diabetes, steatosis, and cirrhosis) and in livers from ob/ob mice. Results:more » In human liver tissues, BPA sulfonation was substantially lower in livers from subjects with steatosis (23%), diabetes cirrhosis (16%), and cirrhosis (18%), relative to healthy individuals with non-fatty livers (100%). In livers of obese mice (ob/ob), BPA sulfonation was lower (23%) than in livers from lean wild-type controls (100%). In addition to BPA sulfonation activity, Sult1a1 protein expression decreased by 97% in obese mouse livers. Conclusion: Taken together these findings establish a profoundly reduced capacity of BPA elimination via sulfonation in obese or diabetic individuals and in those with fatty or cirrhotic livers versus individuals with healthy livers. - Highlights: • Present study demonstrates that hepatic SULT 1A1/1A3 are primarily sulfonate BPA in mouse and human. • Hepatic BPA sulfonation is profoundly reduced steatosis, diabetes and cirrhosis. • With BPA-S detectable in urine under low or common exposures, these findings are novel and important.« less

40 CFR 721.9674 - Sulfonated-copper phthalocyanine salt of a triarylmethane dye (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Sulfonated-copper phthalocyanine salt... Significant New Uses for Specific Chemical Substances § 721.9674 Sulfonated-copper phthalocyanine salt of a... chemical substance identified generically as sulfonated-copper phthalocyanine salt of a triarylmethane dye...

40 CFR 721.9674 - Sulfonated-copper phthalocyanine salt of a triarylmethane dye (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Sulfonated-copper phthalocyanine salt... Significant New Uses for Specific Chemical Substances § 721.9674 Sulfonated-copper phthalocyanine salt of a... chemical substance identified generically as sulfonated-copper phthalocyanine salt of a triarylmethane dye...

40 CFR 721.9674 - Sulfonated-copper phthalocyanine salt of a triarylmethane dye (generic).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Sulfonated-copper phthalocyanine salt... Significant New Uses for Specific Chemical Substances § 721.9674 Sulfonated-copper phthalocyanine salt of a... chemical substance identified generically as sulfonated-copper phthalocyanine salt of a triarylmethane dye...

40 CFR 721.10564 - Mixed amino diaryl sulfone isomers (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Mixed amino diaryl sulfone isomers... Specific Chemical Substances § 721.10564 Mixed amino diaryl sulfone isomers (generic). (a) Chemical... as mixed amino diaryl sulfone isomers (PMN P-08-39) is subject to reporting under this section for...

40 CFR 721.10564 - Mixed amino diaryl sulfone isomers (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Mixed amino diaryl sulfone isomers... Specific Chemical Substances § 721.10564 Mixed amino diaryl sulfone isomers (generic). (a) Chemical... as mixed amino diaryl sulfone isomers (PMN P-08-39) is subject to reporting under this section for...

40 CFR 721.950 - Sodium salt of an alkylated, sulfonated aromatic (generic name).

Code of Federal Regulations, 2010 CFR

2010-07-01

..., sulfonated aromatic (generic name). 721.950 Section 721.950 Protection of Environment ENVIRONMENTAL... Significant New Uses for Specific Chemical Substances § 721.950 Sodium salt of an alkylated, sulfonated... chemical substance identified generically as a sodium salt of an alkylated, sulfonated aromatic (PMN P-84...

40 CFR 721.2565 - Alkylated sulfonated diphenyl oxide, alkali and amine salts.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Alkylated sulfonated diphenyl oxide... New Uses for Specific Chemical Substances § 721.2565 Alkylated sulfonated diphenyl oxide, alkali and... substances identified as alkylated sulfonated diphenyl oxide, alkali salt (PMN P-93-352) and alkylated...

40 CFR 721.2565 - Alkylated sulfonated diphenyl oxide, alkali and amine salts.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Alkylated sulfonated diphenyl oxide... New Uses for Specific Chemical Substances § 721.2565 Alkylated sulfonated diphenyl oxide, alkali and... substances identified as alkylated sulfonated diphenyl oxide, alkali salt (PMN P-93-352) and alkylated...

40 CFR 721.950 - Sodium salt of an alkylated, sulfonated aromatic (generic name).

Code of Federal Regulations, 2011 CFR

2011-07-01

..., sulfonated aromatic (generic name). 721.950 Section 721.950 Protection of Environment ENVIRONMENTAL... Significant New Uses for Specific Chemical Substances § 721.950 Sodium salt of an alkylated, sulfonated... chemical substance identified generically as a sodium salt of an alkylated, sulfonated aromatic (PMN P-84...

40 CFR 721.9674 - Sulfonated-copper phthalocyanine salt of a triarylmethane dye (generic).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Sulfonated-copper phthalocyanine salt... Significant New Uses for Specific Chemical Substances § 721.9674 Sulfonated-copper phthalocyanine salt of a... chemical substance identified generically as sulfonated-copper phthalocyanine salt of a triarylmethane dye...

40 CFR 721.9674 - Sulfonated-copper phthalocyanine salt of a triarylmethane dye (generic).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Sulfonated-copper phthalocyanine salt... Significant New Uses for Specific Chemical Substances § 721.9674 Sulfonated-copper phthalocyanine salt of a... chemical substance identified generically as sulfonated-copper phthalocyanine salt of a triarylmethane dye...

40 CFR 721.5425 - α-Olefin sulfonate, potassium salts.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false α-Olefin sulfonate, potassium salts... Substances § 721.5425 α-Olefin sulfonate, potassium salts. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as an α-olefin sulfonate, potassium salt (PMN...

40 CFR 721.5425 - α-Olefin sulfonate, potassium salts.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false α-Olefin sulfonate, potassium salts... Substances § 721.5425 α-Olefin sulfonate, potassium salts. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as an α-olefin sulfonate, potassium salt (PMN...

40 CFR 721.5425 - α-Olefin sulfonate, potassium salts.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false α-Olefin sulfonate, potassium salts... Substances § 721.5425 α-Olefin sulfonate, potassium salts. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as an α-olefin sulfonate, potassium salt (PMN...

40 CFR 721.5450 - α-Olefin sulfonate, sodium salt.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false α-Olefin sulfonate, sodium salt. 721... Substances § 721.5450 α-Olefin sulfonate, sodium salt. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as α-olefin sulfonate, sodium salt...

40 CFR 721.5425 - α-Olefin sulfonate, potassium salts.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false α-Olefin sulfonate, potassium salts... Substances § 721.5425 α-Olefin sulfonate, potassium salts. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as an α-olefin sulfonate, potassium salt (PMN...

40 CFR 721.5425 - α-Olefin sulfonate, potassium salts.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false α-Olefin sulfonate, potassium salts... Substances § 721.5425 α-Olefin sulfonate, potassium salts. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as an α-olefin sulfonate, potassium salt (PMN...

Flexible bilayers with spontaneous curvature lead to lamellar gels and spontaneous vesicles

PubMed Central

Coldren, Bret A.; Warriner, Heidi; van Zanten, Ryan; Zasadzinski, Joseph A.; Sirota, Eric B.

2006-01-01

Mixtures of cetyltrimethylammonium tosylate (CTAT) and sodium dodecylbenzene sulfonate (SDBS) in water form a fluid lamellar phase at ≤40 wt % water but surprisingly turn into viscous gels at higher water fractions. The gels are characterized by spherulite and other bilayer defects consistent with a low bending elasticity, κ ∼ kBT, and a nonzero spontaneous curvature. Caillé analysis of the small-angle x-ray line shape confirms that for 7:3 wt:wt CTAT:SDBS bilayers at 50% water, κ = 0.62 ± 0.09 kBT and κ̄ = −0.9 ± 0.2 kBT. For 13:7 wt:wt CTAT:SDBS bilayers, the measured bending elasticity decreases with increasing water dilution in good agreement with predictions based on renormalization theory, giving κo = 0.28 kBT. These results show that surfactant mixing is sufficient to make κ ∼ kBT, which promotes strong, Helfrich-type repulsion between bilayers that can dominate the van der Waals attraction. These are necessary conditions for spontaneous vesicles formed at even higher water fractions to be equilibrium structures. PMID:16467142

High-efficiency surfactant prepared from phenolic resin for multi-walled carbon nanotube aqueous suspension

NASA Astrophysics Data System (ADS)

Li, Yutong; Wei, Haixu; Li, Lizhi; Wang, Jie; Qian, Xin; He, Liu; Wang, Xuefei; Ouyang, Qin; Chen, Yousi; Zhang, Yonggang; Li, Yong

2018-06-01

Carbon nanotubes (CNTs) have been widely exploited to be used in many fields due to its perfect mechanical properties, but CNT agglomerates severely prevent CNTs' excellent properties from performing. Many dispersants were synthesized to resolve the difficulty reported in recent years. In this paper, a healthier and cheaper dispersant with phenolic resin as original reagent was synthesized (denoted as AEP-4). Fourier transform infrared spectroscopy, nuclear magnetic resonance, and mass spectra were carried out to characterize chemical structure of reagent and products. Ultraviolet-visible spectroscopy and transmission electron microscopy were employed to evaluate the dispersibility of multi-walled carbon nanotubes (MWCNTs) in aqueous solution. The results showed that AEP-4 containing tertiary ammonium cations exhibited strong ability to disperse MWCNTs in aqueous solution, which showed better dispersion ability than sodium dodecyl benzene sulfonate. The scanning electron microscope results of MWCNT/carbon fiber reinforcements showed that many single MWCNTs showed up and uniformly covered carbon fiber surface in the case of carbon fiber treated by MWCNT/AEP-4 suspension, which reflected that MWCNT suspension with AEP-4 had good dispersion.

Decarboxylation of fatty acids with triruthenium dodecacarbonyl: Influence of the compound structure and analysis of the product mixtures

USDA-ARS?s Scientific Manuscript database

Recently, the decarboxylation of oleic acid (9(Z)-octadecenoic acid) catalyzed by triruthenium dodecacarbonyl, Ru3(CO)12, to give a mixture of heptadecenes with concomitant formation of other hydrocarbons, heptadecane and C17 alkylbenzenes, was reported. The product mixture, consisting of about 77% ...

Geochemistry of the alginite and amorphous organic matter from type II-S kerogens

USGS Publications Warehouse

Stankiewicz, B.A.; Kruge, M.A.; Mastalerz, Maria; Salmon, G.L.

1996-01-01

Maceral fractions of the Type II-S kerogens from the Monterey Formation (Miocene. California. U.S.A.) and Duwi Formation (Campanian/Maastrichtian, Egypt) were separated by density gradient centrifugation. The Monterey Fm. kerogen sample was comprised chiefly of light red-fluorescing amorphous organic matter (AOM), the flash pyrolyzate of which was characterized by a predominance of alkylbenzenes, alkylthiophenes and alkylpyrroles. In contrast, the pyrolyzates of its alginite concentrate showed a highly aliphatic character, typical of this maceral, with the series of n-alkenes and n-alkanes (C6- C26) predominating. The pyrolyzate of the dominant light brown-fluorescing AOM of the Duwi Fm. kerogen had a relatively high concentration of alkylbenzenes and alkylthiophenes, while its elginite concentrate showed a more aliphatic character upon pyrolysis. There was a marked enrichment of thiophenic sulfur in the light-colored AOM of both samples (and also pyrrolic nitrogen in the case of the Monterey) relative to the alginite. The results support a bacterially-mediated, degradative origin for Type II-S amorphous organic matter, with algal remains as the primary source of the kerogen.

Spatial and temporal distribution of aliphatic hydrocarbons and linear alkylbenzenes in the particulate phase from a subtropical estuary (Guaratuba Bay, SW Atlantic) under seasonal population fluctuation.

PubMed

Dauner, Ana Lúcia L; Martins, César C

2015-12-01

Guaratuba Bay, a subtropical estuary located in the SW Atlantic, is under variable anthropogenic pressure throughout the year. Samples of surficial suspended particulate matter (SPM) were collected at 22 sites during three different periods to evaluate the temporal and spatial variability of aliphatic hydrocarbons (AHs) and linear alkylbenzenes (LABs). These compounds were determined by gas chromatography with flame ionization detection (GC-FID) and mass spectrometry (GC/MS). The spatial distributions of both compound classes were similar and varied among the sampling campaigns. Generally, the highest concentrations were observed during the austral summer, highlighting the importance of the increased human influence during this season. The compound distributions were also affected by the natural geochemical processes of organic matter accumulation. AHs were associated with petroleum, derived from boat and vehicle traffic, and biogenic sources, related to mangrove forests and autochthonous production. The LAB composition evidenced preferential degradation processes during the austral summer. Copyright © 2015 Elsevier B.V. All rights reserved.

Application of headspace analysis to the study of sorption of hydrophobic organic chemicals to α-Al2O3

USGS Publications Warehouse

Pelinger, Judith A.; Eisenreich, Steven J.; Capel, Paul D.

1993-01-01

The sorption of hydrophobic organic chemicals (HOCs) to ??-Al2O3 was investigated with a headspace analysis method. The semiautomated headspace analyzer gave rapid, precise, and accurate results for a homologous series alkylbenzenes even at low percentages of solute mass sorbed (3-50%). Sorption experiments carried out with benzene alone indicated weak interactions with well-characterized aluminum oxide, and a solids concentration effect was observed. When the sorption coefficients for benzene alone obtained by headspace analysis were extrapolated up to the solids concentrations typically used in batch sorption experiments, the measured sorption coefficients agreed with reported sorption coefficients for HOCs and sediments of low fractional organic carbon content. Sorbed concentrations increased exponentially with aqueous concentration in isotherms with mixtures of alkylbenzenes, indicating solute-solute interactions at the mineral surface. Sorption was, however, greater than predicted for partitioning of a solute between its pure liquid phase and water, indicating additional influences of the surface and/or the structured liquid near the mineral surface. ?? 1993 American Chemical Society.

Nanoscale structure and morphology of sulfonated polyphenylenes via atomistic simulations

DOE PAGES

Abbott, Lauren J.; Frischknecht, Amalie L.

2017-01-23

We performed atomistic simulations on a series of sulfonated polyphenylenes systematically varying the degree of sulfonation and water content to determine their effect on the nanoscale structure, particularly for the hydrophilic domains formed by the ionic groups and water molecules. We found that the local structure around the ionic groups depended on the sulfonation and hydration levels, with the sulfonate groups and hydronium ions less strongly coupled at higher water contents. In addition, we characterized the morphology of the ionic domains employing two complementary clustering algorithms. At low sulfonation and hydration levels, clusters were more elongated in shape and poorlymore » connected throughout the system. As the degree of sulfonation and water content were increased, the clusters became more spherical, and a fully percolated ionic domain was formed. As a result, these structural details have important implications for ion transport.« less

Mineralization of the sulfonated azo dye Mordant Yellow 3 by a 6-aminonaphthalene-2-sulfonate-degrading bacterial consortium.

PubMed Central

Haug, W; Schmidt, A; Nörtemann, B; Hempel, D C; Stolz, A; Knackmuss, H J

1991-01-01

Under anaerobic conditions the sulfonated azo dye Mordant Yellow 3 was reduced by the biomass of a bacterial consortium grown aerobically with 6-aminonaphthalene-2-sulfonic acid. Stoichiometric amounts of the aromatic amines 6-aminonaphthalene-2-sulfonate and 5-aminosalicylate were generated and excreted into the medium. After re-aeration of the culture, these amines were mineralized by different members of the bacterial culture. Thus, total degradation of a sulfonated azo dye was achieved by using an alternating anaerobic-aerobic treatment. The ability of the mixed bacterial culture to reduce the azo dye was correlated with the presence of strain BN6, which possessed the ability to oxidize various naphthalenesulfonic acids. It is suggested that strain BN6 has a transport system for naphthalenesulfonic acids which also catalyzes uptake of sulfonated azo dyes. These dyes are then gratuitously reduced in the cytoplasm by unspecific reductases. PMID:1781678

40 CFR 721.9595 - Alkyl benzene sulfonic acids and alkyl sulfates, amine salts (generic).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Alkyl benzene sulfonic acids and alkyl... Significant New Uses for Specific Chemical Substances § 721.9595 Alkyl benzene sulfonic acids and alkyl...) The chemical substances identified generically as alkyl benzene sulfonic acids and alkyl sulfates...

40 CFR 721.9595 - Alkyl benzene sulfonic acids and alkyl sulfates, amine salts (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Alkyl benzene sulfonic acids and alkyl... Significant New Uses for Specific Chemical Substances § 721.9595 Alkyl benzene sulfonic acids and alkyl...) The chemical substances identified generically as alkyl benzene sulfonic acids and alkyl sulfates...

40 CFR 721.9595 - Alkyl benzene sulfonic acids and alkyl sulfates, amine salts (generic).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Alkyl benzene sulfonic acids and alkyl... Significant New Uses for Specific Chemical Substances § 721.9595 Alkyl benzene sulfonic acids and alkyl...) The chemical substances identified generically as alkyl benzene sulfonic acids and alkyl sulfates...

40 CFR 721.9595 - Alkyl benzene sulfonic acids and alkyl sulfates, amine salts (generic).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Alkyl benzene sulfonic acids and alkyl... Significant New Uses for Specific Chemical Substances § 721.9595 Alkyl benzene sulfonic acids and alkyl...) The chemical substances identified generically as alkyl benzene sulfonic acids and alkyl sulfates...

40 CFR 721.9595 - Alkyl benzene sulfonic acids and alkyl sulfates, amine salts (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Alkyl benzene sulfonic acids and alkyl... Significant New Uses for Specific Chemical Substances § 721.9595 Alkyl benzene sulfonic acids and alkyl...) The chemical substances identified generically as alkyl benzene sulfonic acids and alkyl sulfates...

In situ S-K XANES study of polymer electrolyte fuel cells: changes in the chemical states of sulfonic groups depending on humidity.

PubMed

Isegawa, Kazuhisa; Nagami, Tetsuo; Jomori, Shinji; Yoshida, Masaaki; Kondoh, Hiroshi

2016-09-14

Changes in the chemical states of sulfonic groups of Nafion in polymer electrolyte fuel cells (PEFCs) under gas-flowing conditions were studied using in situ S-K XANES spectroscopy. The applied potential to the electrodes and the humidity of the cell were changed under flowing H 2 gas in the anode and He gas in the cathode. While the potential shows no significant effect on the S-K XANES spectra, the humidity is found to induce reversible changes in the spectra. Comparison of the spectral changes with simulations based on the density functional theory calculations indicates that the humidity influences the chemical state of the sulfonic group; under wet conditions the sulfonic group is in the form of a sulfonate ion. By drying treatment the sulfonate ion binds to hydrogen and becomes sulfonic acid. Furthermore, a small fraction of the sulfonic acid irreversibly decomposes to atomic sulfur. The peak energy of the atomic sulfur suggests that the generated atomic sulfur is adsorbed on the Pt catalyst surfaces.

Design, fabrication and evaluation of intelligent sulfone-selective polybenzimidazole nanofibers.

PubMed

Ogunlaja, Adeniyi S; du Sautoy, Carol; Torto, Nelson; Tshentu, Zenixole R

2014-08-01

Molecularly imprinted polybenzimidazole nanofibers fabricated for the adsorption of oxidized organosulfur compounds are presented. The imprinted polymers exhibited better selectivity for their target model sulfone-containing compounds with adsorption capacities of 28.5±0.4mg g(-1), 29.8±2.2mg g(-1) and 20.1±1.4mg g(-1) observed for benzothiophene sulfone (BTO2), dibenzothiophene sulfone (DBTO2) and 4,6-dimethyldibenzothiophene sulfone (4,6-DMDBTO2) respectively. Molecular modeling based upon the density functional theory (DFT) indicated that hydrogen bond interactions may take place between sulfone oxygen groups with NH groups of the PBI. Further DFT also confirmed the feasibility of π-π interactions between the benzimidazole rings and the aromatic sulfone compounds. The adsorption mode followed the Freundlich (multi-layered) adsorption isotherm which indicated possible sulfone-sulfone interactions. A home-made pressurized hot water extraction (PHWE) system was employed for the extraction/desorption of sulfone compounds within imprinted nanofibers at 1mL min(-1), 150°C and 30 bar. PHWE used a green solvent (water) and achieved better extraction yields compared to the Soxhlet extraction process. The application of molecularly imprinted polybenzimidazole (PBI) nanofibers displayed excellent sulfur removal, with sulfur in fuel after adsorption falling below the determined limit of detection (LOD), which is 2.4mg L(-1)S, and with a sulfur adsorption capacity of 5.3±0.4mg g(-1) observed for application in the fuel matrix. Copyright © 2014 Elsevier B.V. All rights reserved.

40 CFR 721.6220 - Aryl sulfonate of a fatty acid mixture, polyamine condensate.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Aryl sulfonate of a fatty acid mixture... Specific Chemical Substances § 721.6220 Aryl sulfonate of a fatty acid mixture, polyamine condensate. (a... generically as an aryl sulfonate of a fatty acid mixture, polyamine condensate (PMN P-91-584) is subject to...

40 CFR 721.1225 - Benzene, 1,2-dimethyl-, poly-propene derivatives, sulfonated, po-tas-sium salts.

Code of Federal Regulations, 2010 CFR

2010-07-01

... derivatives, sulfonated, po-tas-sium salts. 721.1225 Section 721.1225 Protection of Environment ENVIRONMENTAL... derivatives, sulfonated, po-tas-sium salts. (a) Chemical substances and significant new uses subject to..., sulfonated, potassium salts (PMN P-89-711) is subject to reporting under this section for the significant new...

40 CFR 721.9597 - Salt of a substituted sulfonated aryl azo compound (generic).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Salt of a substituted sulfonated aryl... New Uses for Specific Chemical Substances § 721.9597 Salt of a substituted sulfonated aryl azo... substance identified generically as salt of a substituted sulfonated aryl azo compound (PMN P-00-0094) is...

40 CFR 721.1225 - Benzene, 1,2-dimethyl-, poly-propene derivatives, sulfonated, po-tas-sium salts.

Code of Federal Regulations, 2011 CFR

2011-07-01

... derivatives, sulfonated, po-tas-sium salts. 721.1225 Section 721.1225 Protection of Environment ENVIRONMENTAL... derivatives, sulfonated, po-tas-sium salts. (a) Chemical substances and significant new uses subject to..., sulfonated, potassium salts (PMN P-89-711) is subject to reporting under this section for the significant new...

40 CFR 721.9597 - Salt of a substituted sulfonated aryl azo compound (generic).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Salt of a substituted sulfonated aryl... New Uses for Specific Chemical Substances § 721.9597 Salt of a substituted sulfonated aryl azo... substance identified generically as salt of a substituted sulfonated aryl azo compound (PMN P-00-0094) is...

Post-sulfonation of cellulose nanofibrils with a one-step reaction to improve dispersibility

Treesearch

Jeffrey Luo; Nikolay Semenikhin; Huibin Chang; Robert J. Moon; Satish Kumar

2018-01-01

Cellulose nanofibrils (CNF) were sulfonated and the dispersion quality was compared to unfunctionalized and 2,2,6,6-tetramethylpiperdine-1-oxyl radical (TEMPO) post-oxidation treatment of existing CNF (mechanically fibrillated pulp). A post-sulfonation treatment on existing CNF in chlorosulfonic acid and dimethylformamide (DMF) resulted in sulfonated CNF that retained...

40 CFR 721.644 - Amines, C12-14-tert-alkyl, sulfonates.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Amines, C12-14-tert-alkyl, sulfonates... Substances § 721.644 Amines, C12-14-tert-alkyl, sulfonates. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as amines, C12-14-tert-alkyl, sulfonates (PMN...

40 CFR 721.6220 - Aryl sulfonate of a fatty acid mixture, polyamine condensate.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Aryl sulfonate of a fatty acid mixture... Specific Chemical Substances § 721.6220 Aryl sulfonate of a fatty acid mixture, polyamine condensate. (a... generically as an aryl sulfonate of a fatty acid mixture, polyamine condensate (PMN P-91-584) is subject to...

40 CFR 721.644 - Amines, C12-14-tert-alkyl, sulfonates.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Amines, C12-14-tert-alkyl, sulfonates... Substances § 721.644 Amines, C12-14-tert-alkyl, sulfonates. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as amines, C12-14-tert-alkyl, sulfonates (PMN...

Sulfonates: A novel class of organic sulfur compounds in marine sediments

NASA Astrophysics Data System (ADS)

Vairavamurthy, Appathurai; Zhou, Weiqing; Eglinton, Timothy; Manowitz, Bernard

1994-11-01

X-ray absorption near-edge structure spectroscopy (XANES) used to measure sulfur speciation in a variety of organic-rich marine sediments has established sulfonates as a novel and major component of sedimentary organic sulfur. The origins of sulfonates in sediments are not clear, although both biological and geochemical mechanisms are possible. The accumulation of oxidized sulfonate sulfur in reducing marine sediments was not known previously; hence, a new perspective in sulfur geochemistry is established. The biogeochemical implications of the presence of sulfonates in marine sediments are discussed.

Sulfonation and anticoagulant activity of botryosphaeran from Botryosphaeria rhodina MAMB-05 grown on fructose.

PubMed

Mendes, Simone Ferreira; dos Santos, Osvaldo; Barbosa, Aneli M; Vasconcelos, Ana Flora D; Aranda-Selverio, Gabriel; Monteiro, Nilson K; Dekker, Robert F H; Sá Pereira, Mariana; Tovar, Ana Maria F; Mourão, Paulo A de Souza; da Silva, Maria de Lourdes Corradi

2009-10-01

Botryosphaeran (EPS(FRU)), an exopolysaccharide of the beta-(1-->3,1-->6)-d-glucan type with 31% branching at C-6, is produced by the fungus Botryosphaeria rhodina MAMB-05 when grown on fructose as carbon source. Botryosphaeran was derivatized by sulfonation to induce anticoagulant activity. The effectiveness of the sulfonation reaction by chlorosulfonic acid in pyridine was monitored by the degree of substitution and FT-IR analysis of the sulfonated EPS(FRU) (once sulfonated, EPS(FRUSULF); and re-sulfonated, EPS(FRURESULF)). Activated partial thromboplastin time (APTT) and thrombin time (TT) tests of EPS(FRURESULF) indicated significant in vitro anticoagulant activity that was dose-dependent. EPS(FRU) did not inhibit any of the coagulation tests.

Sodium Polystyrene Sulfonate

MedlinePlus

Sodium polystyrene sulfonate is used to treat hyperkalemia (increased amounts of potassium in the body). Sodium polystyrene sulfonate is in a class of medications called potassium-removing agents. It works by ...

A study of the effect of polystyrene sulfonation on the performance of terephthaloyl chloride-dihydroxydiphenyl sulfone copolymer/polystyrene system

NASA Astrophysics Data System (ADS)

Kahraman, R.; Kahn, K. A.; Ali, S. A.; Hamid, S. H.; Sahin, A. Z.

1998-12-01

Thermal, morphological, and mechanical properties of composites of a liquid crystalline copolymer (LCP) poly(terephthaloyl chloride)-co-(p,p’-dihydroxydiphenyl sulfone) with polystyrene (PS) and sulfonated polystyrene (SPS) are presented and discussed. Sulfonation of polystyrene was expected to improve the interfacial adhesion by introducing hydrogen bonding in the LCP/PS system. The degree of sulfonation was 11 %. The incompatibility (lack of proper interfacial adhesion) of the LCP/PS system resulted in sharp decrease in the composite tensile strength with LCP addition. The performance of the system did not change when processed at a higher temperature (270 °C instead of 225 °C). While a composite plate of 25% LCP/PS could not be fabricated, it was possible for LCP/SPS (processed at 215 °C), indicating some improvement in interfacial bonding by sulfonation. Sulfonation of PS resulted in fracture with some degree of plastic deformation for pure SPS matrix and also the LCP/SPS system with the lowest LCP content (1 wt%), whereas plastic deformation was not observed for PS used as received. The strength of the LCP/SPS system also decreased with increase in LCP content, indicating that 11% sulfonation is not sufficient to introduce significant compatibility, but it was not as dramatic as that for LCP/PS. The performance of the LCP/SPS system was not affected significantly by heat treatment at the process temperature.

Sulfonated polystyrene and its characterization as a material of electrolyte polymer

NASA Astrophysics Data System (ADS)

Ngadiwiyana; Ismiyarto; Gunawan; Purbowatiningrum, RS; Prasetya, N. B. A.; Kusworo, T. D.; Susanto, H.

2018-05-01

The research of polystyrene modification from Styrofoam waste and its application as a main material of electrolyte polymer had been done. The sulfonation reaction of polystyrene was conducted using sulfuric acid as sufonation agent and the reactions were done with variation times of 1, 2, 3, 4 and 5 h. The characterization of the sulfonated products covered analysis of functional groups using FT-IR spectrophotometer, sulfonation degree, measurements of ion exchange capacity, conductivity and swelling degree. The sulfonated polystyrene product was white solid as confirmed by the spectra of FT-IR with the presence of wide band absorption of O=S=O at the wavenumber of 1080-1411 cm-1 as indication. The research showed the best sulfonated polystyrene prepared in 4 h as a material of electrolyte polymer, since it had the highest degree of sulfonation, ion exchange capacity, conductivity and swelling degree with the values were 28.52 %, 1.550 meg/g, 15,924.10-6 Ω-1cm-1 and 332.4 %, respectively.

Polymer electrolytes based on sulfonated polysulfone for direct methanol fuel cells

NASA Astrophysics Data System (ADS)

Lufrano, F.; Baglio, V.; Staiti, P.; Arico', A. S.; Antonucci, V.

This paper reports the development and characterization of sulfonated polysulfone (SPSf) polymer electrolytes for direct methanol fuel cells. The synthesis of sulfonated polysulfone was performed by a post sulfonation method using trimethyl silyl chlorosulfonate as a mild sulfonating agent. Bare polysulfone membranes were prepared with two different sulfonation levels (60%, SPSf-60 and 70%, SPSf-70), whereas, a composite membrane of SPSf-60 was prepared with 5 wt% silica filler. These membranes were investigated in direct methanol fuel cells (DMFCs) operating at low (30-40 °C) and high temperatures (100-120 °C). DMFC power densities were about 140 mW cm -2 at 100 °C with the bare SPSf-60 membrane and 180 mW cm -2 at 120 °C with the SPSf-60-SiO2 composite membrane. The best performance achieved at ambient temperature using a membrane with high degree of sulfonation (70%, SPSf-70) was 20 mW cm -2 at atmospheric pressure. This makes the polysulfone-based DMFC suitable for application in portable devices.

Resin catalysts and method of preparation

DOEpatents

Smith, Jr., Lawrence A.

1986-01-01

Heat stabilized catalyst compositions are prepared from nuclear sulfonic acid, for example, macroporous crosslinked polyvinyl aromatic compounds containing sulfonic acid groups are neutralized with a metal of Al, Fe, Zn, Cu, Ni, ions or mixtures and alkali, alkaline earth metals or ammonium ions by contacting the resin containing the sulfonic acid with aqueous solutions of the metals salts and alkali, alkaline earth metal or ammonium salts. The catalysts have at least 50% of the sulfonic acid groups neutralized with metal ions and the balance of the sulfonic acid groups neutralized with alkali, alkaline earth ions or ammonium ions.

Synthesis and Characterization of Polymers for Fuel Cells Application

NASA Technical Reports Server (NTRS)

Tytko, Stephen F.

2003-01-01

The goal of this summer research is to prepare Polymer Exchange Membranes (PEM s) for fuel cell application. Several high temperature polymers such as polybenzimidazoles and polyether ketones were known to possess good high temperature stability and had been investigated by post-sulfonation to yield sulfonated polymers. The research project will involve two approaches: 1. Synthesis of polybenzimidazoles and then react with alkyl sultonse to attach an aliphatic sulfonic groups. 2. Synthesis of monomers containing sulfonic acid units either on a aromatic ring or on an aliphatic chain and then polymerize the monomers to form high molecular weight sulfonate polymers.

Resin catalysts and method of preparation

DOEpatents

Smith, L.A. Jr.

1986-12-16

Heat stabilized catalyst compositions are prepared from nuclear sulfonic acid, for example, macroporous crosslinked polyvinyl aromatic compounds containing sulfonic acid groups are neutralized with a metal of Al, Fe, Zn, Cu, Ni, ions or mixtures and alkali, alkaline earth metals or ammonium ions by contacting the resin containing the sulfonic acid with aqueous solutions of the metals salts and alkali, alkaline earth metal or ammonium salts. The catalysts have at least 50% of the sulfonic acid groups neutralized with metal ions and the balance of the sulfonic acid groups neutralized with alkali, alkaline earth ions or ammonium ions.

Use of extant kinetic parameters to predict effluent concentrations of specific organic compounds at full-scale facilities.

PubMed

Ellis, Timothy G; Eliosov, Boris

2004-01-01

To use the results of kinetic tests to predict effluent concentrations of specific contaminants in activated sludge systems, the fraction of the biomass that has an ability to degrade the test compound (i.e., competent biomass) must be estimated. A calibration procedure was developed to assess the competent biomass concentration because the chemical oxygen demand (COD) fraction tended to underestimate the degrading fraction for three of the four test compounds. Acetone, for instance, had a measured influent COD fraction of 0.08%, and the actual competent fraction was estimated to be 2.3%, based on the model calibration. Once the competent biomass fraction in the mixed liquor was determined, the extant kinetic parameters were subsequently used to predict activated sludge system performance. Predicted effluent concentrations were within 2, 5, and 16% of the average measured concentrations for acetone, linear alkylbenzene sulfonate, and furfural, respectively. Day-to-day predictions for these compounds were less accurate, possibly because of the non-steady-state nature of the activated sludge systems studied. The difference between the fraction of the influent COD contributed by the target compounds and the competent biomass fraction in the mixed liquor was found to be more significant when the target compound contributed less than 1% of the influent organic matter. The chemical structure of the target compound and chemical composition of the influent likely had an effect on the resulting competent biomass concentration. The total maximum growth rate, microX, was observed to be independent of the influent concentration of acetone and furfural, thus suggesting that the competent biomass concentration for these compounds was not affected by the changes in their influent concentrations. Consequently, a majority of competent biomass growth resulted from the degradation of other substrates, resulting in a competent biomass concentration significantly higher than predicted based on the influent COD fraction contributed by the test compound.

Polymer Brushes Containing Sulfonated Sugar Repeat Units: Synthesis, Characterization and In Vitro Testing of Blood Coagulation Activation

PubMed Central

Ayres, N.; Holt, D. J.; Jones, C.F.; Corum, L. E.; Grainger, D. W.

2009-01-01

A new polymer brush chemistry containing sulfonated carbohydrate repeat units has been synthesized from silicon substrates using ATRP methods and characterized both in bulk and using surface analysis. The polymer brush was designed to act as a mimic for the naturally occurring sulfonated glycosaminoglycan, heparin, commonly used for modifying blood-contacting surfaces both in vitro and in vivo. Surface analysis showed conversion of brush saccharide precursor chemistry to the desired sulfonated polymer product. The sulfonated polymer brush surface was further analyzed using three conventional in vitro tests for blood compatibility -- plasma recalcification times, complement activation, and thrombin generation. The sulfonated polymer brush films on silicon oxide wafers exhibited better assay performance in these blood component assays than the unsulfonated sugar functionalized polymer brush in all tests performed. PMID:19859552

Adsorption mechanism of mixed cationic/anionic collectors in feldspar-quartz flotation system.

PubMed

Vidyadhar, A; Hanumantha Rao, K

2007-02-15

The adsorption mechanism of mixed cationic alkyl diamine and anionic sulfonate/oleate collectors at acidic pH values was investigated on microcline and quartz minerals through Hallimond flotation, electrokinetic and diffuse reflectance FTIR studies. In the presence of anionic collectors, neither of the minerals responded to flotation but the diamine flotation of the minerals was observed to be pH and concentration dependent. The presence of sulfonate enhanced the diamine flotation of the minerals by its co-adsorption. The difference in surface charge between the minerals at pH 2 was found to be the basis for preferential feldspar flotation from quartz in mixed diamine/sulfonate collectors. The infrared spectra revealed no adsorption of sulfonate collector when used alone but displayed its co-adsorption as diamine-sulfonate complex when used with diamine. The presence of sulfonate increased the diamine adsorption due to a decrease in the electrostatic head-head repulsion between the adjacent surface ammonium ions and thereby increasing the lateral tail-tail hydrophobic bonds. The mole ratio of diamine/sulfonate was found to be an important factor in the orientation of alkyl chains and thus the flotation response of minerals. The increase in sulfonate concentration beyond diamine concentration leads to the formation of soluble 1:2 diamine-sulfonate complex or precipitate and the adsorption of these species decreased the flotation since the alkyl chains are in chaotical orientation with a conceivable number of head groups directing towards the solution phase.

Production and Application of Lignosulfonates and Sulfonated Lignin.

PubMed

Aro, Thomas; Fatehi, Pedram

2017-05-09

Lignin is the largest reservoir of aromatic compounds on earth and has great potential to be used in many industrial applications. Alternative methods to produce lignosulfonates from spent sulfite pulping liquors and kraft lignin from black liquor of kraft pulping process are critically reviewed herein. Furthermore, options to increase the sulfonate contents of lignin-based products are outlined and the industrial attractiveness of them is evaluated. This evaluation includes sulfonation and sulfomethylation of lignin. To increase the sulfomethylation efficiency of lignin, various scenarios, including hydrolysis, oxidation, and hydroxymethylation, were compared. The application of sulfonated lignin-based products is assessed and the impact of the properties of these products on the characteristics of their end-use application is critically evaluated. Sulfonated lignin-based products have been used as dispersants in cement admixtures and dye solutions more than other applications, and their molecular weight and degree of sulfonation were crucial in determining their efficiency. The use of lignin-based sulfonated products in composites may result in an increase in the hydrophilicity of some composites, but the sulfonated products may need to be desulfonated with an alkali and/or oxygen prior to their use in composites. To be used as a flocculant, sulfonated lignin-based products may need to be cross-linked to increase their molecular weight. The challenges associated with the use of lignin-based products in these applications are comprehensively discussed herein. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Processes for preparing carbon fibers using gaseous sulfur trioxide

DOEpatents

Barton, Bryan E.; Lysenko, Zenon; Bernius, Mark T.; Hukkanen, Eric J.

2016-01-05

Disclosed herein are processes for preparing carbonized polymers, such as carbon fibers, comprising: sulfonating a polymer with a sulfonating agent that comprises SO.sub.3 gas to form a sulfonated polymer; treating the sulfonated polymer with a heated solvent, wherein the temperature of said solvent is at least 95.degree. C.; and carbonizing the resulting product by heating it to a temperature of 500-3000.degree. C.

Blood Compatibility of Sulfonated Cladophora Nanocellulose Beads.

PubMed

Rocha, Igor; Lindh, Jonas; Hong, Jaan; Strømme, Maria; Mihranyan, Albert; Ferraz, Natalia

2018-03-07

Sulfonated cellulose beads were prepared by oxidation of Cladophora nanocellulose to 2,3-dialdehyde cellulose followed by sulfonation using bisulfite. The physicochemical properties of the sulfonated beads, i.e., high surface area, high degree of oxidation, spherical shape, and the possibility of tailoring the porosity, make them interesting candidates for the development of immunosorbent platforms, including their application in extracorporeal blood treatments. A desired property for materials used in such applications is blood compatibility; therefore in the present work, we investigate the hemocompatibility of the sulfonated cellulose beads using an in vitro whole blood model. Complement system activation (C3a and sC5b-9 levels), coagulation activation (thrombin-antithrombin (TAT) levels) and hemolysis were evaluated after whole blood contact with the sulfonated beads and the results were compared with the values obtained with the unmodified Cladophora nanocellulose. Results showed that neither of the cellulosic materials presented hemolytic activity. A marked decrease in TAT levels was observed after blood contact with the sulfonated beads, compared with Cladophora nanocellulose. However, the chemical modification did not promote an improvement in Cladophora nanocellulose hemocompatibility in terms of complement system activation. Even though the sulfonated beads presented a significant reduction in pro-coagulant activity compared with the unmodified material, further modification strategies need to be investigated to control the complement activation by the cellulosic materials.

Deetherification process

DOEpatents

Smith, Jr., Lawrence A.

1985-01-01

Ethers such as isobutyl tertiary butyl ether are dissociated into their component alcohols and isolefins by heat stabilized catalyst compositions prepared from nuclear sulfonic acid, for example, macroporous crosslinked polyvinyl aromatic compounds containing sulfonic acid groups are neutralized with a metal of Al, Fe, Zn, Cu, Ni, ions or mixtures and alkali, alkaline earth metals or ammonium ions by contacting the resin containing the sulfonic acid with aqueous solutions of the metals salts and alkali, alkaline earth metal or ammonium salts. The catalysts have at least 50% of the sulfonic acid groups neutralized with metal ions and the balance of the sulfonic acid groups neutralized with alkali, alkaline earth ions or ammonium ions.

Deetherification process

DOEpatents

Smith, L.A. Jr.

1985-11-05

Ethers such as isobutyl tertiary butyl ether are dissociated into their component alcohols and isoolefins by heat stabilized catalyst compositions prepared from nuclear sulfonic acid, for example, macroporous crosslinked polyvinyl aromatic compounds containing sulfonic acid groups are neutralized with a metal of Al, Fe, Zn, Cu, Ni, ions or mixtures and alkali, alkaline earth metals or ammonium ions by contacting the resin containing the sulfonic acid with aqueous solutions of the metals salts and alkali, alkaline earth metal or ammonium salts. The catalysts have at least 50% of the sulfonic acid groups neutralized with metal ions and the balance of the sulfonic acid groups neutralized with alkali, alkaline earth ions or ammonium ions.

CORROSION PREVENTION OF COLD ROLLED STEEL USING WATER DISPERSIBLE LIGNOSULFONIC ACID DOPED POLYANILINE

NASA Technical Reports Server (NTRS)

Viswanathan, Tito (Inventor)

2005-01-01

The invention provides coatings useful for preventing corrosion of metals. The coatings comprise a film-forming resin and conductive polymers comprising linearly conjugated pi-systems and residues of sulfonated lignin or a sulfonated polyflavonoid or derivatives of sulfonated lignin or a sulfonated polyflavonoid. The invention also provides a latex formulation of the coatings, and articles of manufacture comprising a metal substrate and a coating in contact with the metal substrate.

Natural attenuation of volatile organic compounds (VOCs) in the leachate plume of a municipal landfill: Using alkylbenzenes as process probes

USGS Publications Warehouse

Eganhouse, R.P.; Cozzarelli, I.M.; Scholl, M.A.; Matthews, L.L.

2001-01-01

More than 70 individual VOCs were identified in the leachate plume of a closed municipal landfill. Concentrations were low when compared with data published for other landfills, and total VOCs accounted for less than 0.1% of the total dissolved organic carbon. The VOC concentrations in the core of the anoxic leachate plume are variable, but in all cases they were found to be near or below detection limits within 200 m of the landfall. In contrast to the VOCs, the distributions of chloride ion, a conservative tracer, and nonvolatile dissolved organic carbon, indicate little dilution over the same distance. Thus, natural attentuation processes are effectively limiting migration of the VOC plume. The distribution of C2-3-benzenes, paired on the basis of their octanol-water partition coefficients and Henry's law constants, were systematically evaluated to assess the relative importance of volatilization, sorption, and biodegradation as attenuation mechanisms. Based on our data, biodegradation appears to be the process primarily responsible for the observed attenuation of VOCs at this site. We believe that the alkylbenzenes are powerful process probes that can and should be exploited in studies of natural attenuation in contaminated ground water systems.

Adsorption of sophorolipid biosurfactants on their own and mixed with sodium dodecyl benzene sulfonate, at the air/water interface.

PubMed

Chen, Minglei; Dong, Chuchuan; Penfold, Jeff; Thomas, Robert K; Smyth, Thomas J P; Perfumo, Amedea; Marchant, Roger; Banat, Ibrahim M; Stevenson, Paul; Parry, Alyn; Tucker, Ian; Campbell, Richard A

2011-07-19

The adsorption of the lactonic (LS) and acidic (AS) forms of sophorolipid and their mixtures with the anionic surfactant sodium dodecyl benzene sulfonate (LAS) has been measured at the air/water interface by neutron reflectivity, NR. The AS and LS sophorolipids adsorb with Langmuir-like adsorption isotherms. The more hydrophobic LS is more surface active than the AS, with a lower critical micellar concentration, CMC, and stronger surface adsorption, with an area/molecule ∼70 Å(2) compared with 85 Å(2) for the AS. The acidic sophorolipid shows a maximum in its adsorption at the CMC which appears to be associated with a mixture of different isomeric forms. The binary LS/AS and LS/LAS mixtures show a strong surface partitioning in favor of the more surface active and hydrophobic LS component but are nevertheless consistent with ideal mixing at the interface. In contrast, the surface composition of the AS/LAS mixture is much closer to the solution composition, but the surface mixing is nonideal and can be accounted for by regular solution theory, RST. In the AS/LS/LAS ternary mixtures, the surface adsorption is dominated by the sophorolipid, and especially the LS component, in a way that is not consistent with the observations for the binary mixtures. The extreme partitioning in favor of the sophorolipid for the LAS/LS/AS (1:2) mixtures is attributed to a reduction in the packing constraints at the surface due to the AS component. Measurements of the surface structure reveal a compact monolayer for LS and a narrow solvent region for LS, LS/AS, and LS/LAS mixtures, consistent with the more hydrophobic nature of the LS component. The results highlight the importance of the relative packing constraints on the adsorption of multicomponent mixtures, and the impact of the lactonic form of the sophorolipid on the adsorption of the sophorolipid/LAS mixtures.

Pyrimidine Nucleosides with a Reactive (β-Chlorovinyl)sulfone or (β-Keto)sulfone Group at the C5 Position, Their Reactions with Nucleophiles and Electrophiles, and Their Polymerase-Catalyzed Incorporation into DNA

PubMed Central

2018-01-01

Transition-metal-catalyzed chlorosulfonylation of 5-ethynylpyrimidine nucleosides provided (E)-5-(β-chlorovinyl)sulfones A, which undergo nucleophilic substitution with amines or thiols affording B. The treatment of vinyl sulfones A with ammonia followed by acid-catalyzed hydrolysis of the intermediary β-sulfonylvinylamines gave 5-(β-keto)sulfones C. The latter reacts with electrophiles, yielding α-carbon-alkylated or -sulfanylated analogues D. The 5′-triphosphates of A and C were incorporated into double-stranded DNA, using open and one-nucleotide gap substrates, by human or Escherichia coli DNA-polymerase-catalyzed reactions. PMID:29732453

Sulfonated chitosan and dopamine based coatings for metallic implants in contact with blood.

PubMed

Campelo, Clayton S; Chevallier, Pascale; Vaz, Juliana M; Vieira, Rodrigo S; Mantovani, Diego

2017-03-01

Thrombosis and calcification constitute the main clinical problems when blood-interacting devices are implanted in the body. Coatings with thin polymer layers represent an acknowledged strategy to modulate interactions between the material surface and the blood environment. To ensure the implant success, at short-term the coating should limit platelets adhesion and delay the clot formation, and at long-term it should delay the calcification process. Sulfonated chitosan, if compared to native chitosan, shows the unique ability to reduce proteins adsorption, decrease thrombogenic properties and limit calcification. In this work, stainless steel surfaces, commonly used for cardiovascular applications, were coated with sulfonated chitosan, by using dopamine and PEG as anchors, and the effect of these grafted surfaces on platelet adhesion, clot formation as well as on calcification were investigated. Surface characterization techniques evidenced that the coating formation was successful, and the sulfonated chitosan grafted sample exhibited a higher roughness and hydrophilicity, if compared to native chitosan one. Moreover, sulfonated surface limited platelet activation and the process of clot formation, thus confirming its high biological performances in blood. Calcium deposits were also lower on the sulfonated chitosan sample compared to the chitosan one, thus showing that calcification was minimal in presence of sulfonate groups. In conclusion, this sulfonated-modified surface has potential to be as blood-interacting material. Copyright © 2016. Published by Elsevier B.V.

MATERNAL AND DEVELOPMENTAL TOXICITY OF PERFLUOROOCTANE SULFONATE IN THE RAT

EPA Science Inventory

MATERNAL AND DEVELOPMENTAL TOXICITY OF PERFLUOROOCTANE SULFONATE IN THE RAT.
C. Lau and J.M. Rogers, Reproductive Toxicology Division, NHEERL, ORD, USEPA, Research Triangle Park, NC, USA

Perfluorooctane sulfonate (PFOS), an environmentally persistent compound used ...

Two-step sulfonation process for the conversion of polymer fibers to carbon fibers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barton, Bryan E.; Patton, Jasson T.; Hukkanen, Eric J.

Disclosed herein are processes for preparing carbon fibers, comprising: sulfonating a polymer fiber with a sulfonating agent that is fuming sulfuric acid, sulfuric acid, chlorosulfonic acid, or a combination thereof; treating the sulfonated polymer with a heated solvent, wherein the temperature of the heated solvent is at least 95.degree. C.; and carbonizing the resulting product by heating it to a temperature of 501-3000.degree. C. Carbon fibers prepared according to these methods are also disclosed herein.

Processes for preparing carbon fibers using sulfur trioxide in a halogenated solvent

DOEpatents

Patton, Jasson T.; Barton, Bryan E.; Bernius, Mark T.; Chen, Xiaoyun; Hukkanen, Eric J.; Rhoton, Christina A.; Lysenko, Zenon

2015-12-29

Disclosed here are processes for preparing carbonized polymers (preferably carbon fibers), comprising sulfonating a polymer with a sulfonating agent that comprises SO.sub.3 dissolved in a solvent to form a sulfonated polymer; treating the sulfonated polymer with a heated solvent, wherein the temperature of the solvent is at least 95.degree. C.; and carbonizing the resulting product by heating it to a temperature of 500-3000.degree. C. Carbon fibers made according to these methods are also disclosed herein.

Use of albendazole sulfoxide, albendazole sulfone, and combined solutions as scolicidal agents on hydatid cysts (in vitro study)

PubMed Central

Adas, Gokhan; Arikan, Soykan; Kemik, Ozgur; Oner, Ali; Sahip, Nilgun; Karatepe, Oguzhan

2009-01-01

AIM: To establish which scolicidal agents are superior and more suitable for regular use. METHODS: Echinococcus granulosus protoscoleces were obtained from 25 patients with liver hydatid cysts. Various concentrations of albendazole sulfone, albendazole sulfoxide, and albendazole sulfone and albendazole sulfoxide mixed together in concentrations of 50 μg/mL, and H2O2 in a concentration of 4%, NaCl 20%, and 1.5% cetrimide-0.15% chlorhexidine (10% Savlon-Turkey) were used to determine the scolicidal effects. Albendazole (ABZ) derivatives and other scolicidal agents were applied to a minimum of 100 scoleces for 5 and 10 min. The degree of viability was calculated according to the number of living scolices per field from a total of 100 scolices observed under the microscope. RESULTS: After 5 min, ABZ sulfone was 97.3% effective, ABZ sulfoxide was 98.4% effective, and the combined solution was 98.6% effective. When sulfone, sulfoxide and the combined solutions were compared, the combined solution seemed more effective than sulfone. However, there was no difference when the combined solution was compared with sulfoxide. After 10 min, hypertonic salt water, sulfone, sulfoxide, and the combined solution compared to other solutions looked more effective and this was statistically significant on an advanced level. When sulfone, sulfoxide, and the combined solutions were compared with each other, the combined solution appeared more effective than sulfone. When the combined solution was compared with sulfoxide, there was no difference. CONCLUSION: Despite being active, ABZ metabolites did not provide a marked advantage over 20% hypertonic saline. According to these results, we think creating a newly improved and more active preparation is necessary for hydatid cyst treatment. PMID:19115476

Direct Synthesis of Renewable Dodecanol and Dodecane with Methyl Isobutyl Ketone over Dual-Bed Catalyst Systems.

PubMed

Sheng, Xueru; Li, Ning; Li, Guangyi; Wang, Wentao; Wang, Aiqin; Cong, Yu; Wang, Xiaodong; Zhang, Tao

2017-03-09

For the first time, we demonstrated two integrated processes for the direct synthesis of dodecanol or 2,4,8-trimethylnonane (a jet fuel range C 12 -branched alkane) using methyl isobutyl ketone (MIBK) that can be derived from lignocellulose. The reactions were carried out in dual-bed continuous flow reactors. In the first bed, MIBK was selectively converted to a mixture of C 12 alcohol and ketone. Over the Pd-modified magnesium- aluminium hydrotalcite (Pd-MgAl-HT) catalyst, a high total carbon yield (73.0 %) of C 12 oxygenates can be achieved under mild conditions. In the second bed, the C 12 oxygenates generated in the first bed were hydrogenated to dodecanol over a Ru/C catalyst or hydrodeoxygenated to 2,4,8-trimethylnonane over a Cu/SiO 2 catalyst. The as-obtained dodecanol can be used as feedstock in the production of sodium dodecylsulfate (SDS) and sodium dodecyl benzene sulfonate (SDBS), which are widely used as surfactants or detergents. The asobtained 2,4,8-trimethylnonane can be blended into conventional jet fuel without hydroisomerization. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Diamond nanoparticles as a support for Pt and PtRu catalysts for direct methanol fuel cells.

PubMed

La-Torre-Riveros, Lyda; Guzman-Blas, Rolando; Méndez-Torres, Adrián E; Prelas, Mark; Tryk, Donald A; Cabrera, Carlos R

2012-02-01

Diamond in nanoparticle form is a promising material that can be used as a robust and chemically stable catalyst support in fuel cells. It has been studied and characterized physically and electrochemically, in its thin film and powder forms, as reported in the literature. In the present work, the electrochemical properties of undoped and boron-doped diamond nanoparticle electrodes, fabricated using the ink-paste method, were investigated. Methanol oxidation experiments were carried out in both half-cell and full fuel cell modes. Platinum and ruthenium nanoparticles were chemically deposited on undoped and boron doped diamond nanoparticles through the use of NaBH(4) as reducing agent and sodium dodecyl benzene sulfonate (SDBS) as a surfactant. Before and after the reduction process, samples were characterized by electron microscopy and spectroscopic techniques. The ink-paste method was also used to prepare the membrane electrode assembly with Pt and Pt-Ru modified undoped and boron-doped diamond nanoparticle catalytic systems, to perform the electrochemical experiments in a direct methanol fuel cell system. The results obtained demonstrate that diamond supported catalyst nanomaterials are promising for methanol fuel cells.

In-situ suspended aggregate microextraction of gold nanoparticles from water samples and determination by electrothermal atomic absorption spectrometry.

PubMed

Choleva, Tatiana G; Kappi, Foteini A; Tsogas, George Z; Vlessidis, Athanasios G; Giokas, Dimosthenis L

2016-05-01

This work describes a new method for the extraction and determination of gold nanoparticles in environmental samples by means of in-situ suspended aggregate microextraction and electrothermal atomic absorption spectrometry. The method relies on the in-situ formation of a supramolecular aggregate phase through ion-association between a cationic surfactant and a benzene sulfonic acid derivative. Gold nanoparticles are physically entrapped into the aggregate phase which is separated from the bulk aqueous solution by vacuum filtration on the surface of a cellulose filter in the form of a thin film. The film is removed from the filter surface and is dissociated into an acidified methanolic solution which is used for analysis. Under the optimized experimental conditions, gold nanoparticles can be efficiently extracted from water samples with recovery rates between 81.0-93.3%, precision 5.4-12.0% and detection limits as low as 75femtomolL(-1) using only 20mL of sample volume. The satisfactory analytical features of the method along with the simplicity indicate the efficiency of this new approach to adequately collect and extract gold nanoparticle species from water samples. Copyright © 2016 Elsevier B.V. All rights reserved.

An exploratory investigation of polar organic compounds in waters from a lead–zinc mine and mill complex

USGS Publications Warehouse

Rostad, Colleen E.; Schmitt, Christopher J.; Schumacher, John G.; Leiker, Thomas J.

2011-01-01

Surface water samples were collected in 2006 from a lead mine-mill complex in Missouri to investigate possible organic compounds coming from the milling process. Water samples contained relatively high concentrations of dissolved organic carbon (DOC; greater than 20 mg/l) for surface waters but were colorless, implying a lack of naturally occurring aquatic humic or fulvic acids. Samples were extracted by three different types of solid-phase extraction and analyzed by electrospray ionization/mass spectrometry. Because large amounts of xanthate complexation reagents are used in the milling process, techniques were developed to extract and analyze for sodium isopropyl xanthate and sodium ethyl xanthate. Although these xanthate reagents were not found, trace amounts of the degradates, isopropyl xanthyl thiosulfonate and isopropyl xanthyl sulfonate, were found in most locations sampled, including the tailings pond downstream. Dioctyl sulfosuccinate, a surfactant and process filtering aid, was found at concentrations estimated at 350 μg/l at one mill outlet, but not downstream. Release of these organic compounds downstream from lead-zinc mine and milling areas has not previously been reported. A majority of the DOC remains unidentified.

Formation and Fate of Bacterial Sulfonates

DTIC Science & Technology

1989-01-05

sulfonates under phototrophic, anaerobic conditions’ Three cyanobacteria--a strain each of Synechococcus, Anabena, and Nostoc --have been examined for...their ability to utilize the sulfonate taurine as sole source of S for their oxygenic phototrophic growth; only Anabena and Nostoc were able to do so, and

21 CFR 172.824 - Sodium mono- and dimethyl naphthalene sulfonates.

Code of Federal Regulations, 2010 CFR

2010-04-01

... SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) FOOD ADDITIVES PERMITTED FOR DIRECT ADDITION TO FOOD FOR HUMAN CONSUMPTION Multipurpose Additives § 172.824 Sodium mono- and dimethyl naphthalene sulfonates. The food additive sodium mono- and dimethyl naphthalene sulfonates may be safely used in...

Metabolism of Hydrocarbons in n-Alkane-Utilizing Anaerobic Bacteria.

PubMed

Wilkes, Heinz; Buckel, Wolfgang; Golding, Bernard T; Rabus, Ralf

2016-01-01

The glycyl radical enzyme-catalyzed addition of n-alkanes to fumarate creates a C-C-bond between two concomitantly formed stereogenic carbon centers. The configurations of the two diastereoisomers of the product resulting from n-hexane activation by the n-alkane-utilizing denitrifying bacterium strain HxN1, i.e. (1-methylpentyl)succinate, were assigned as (2S,1'R) and (2R,1'R). Experiments with stereospecifically deuterated n-(2,5-2H2)hexanes revealed that exclusively the pro-S hydrogen atom is abstracted from C2 of the n-alkane by the enzyme and later transferred back to C3 of the alkylsuccinate formed. These results indicate that the alkylsuccinate-forming reaction proceeds with an inversion of configuration at the carbon atom (C2) of the n-alkane forming the new C-C-bond, and thus stereochemically resembles a SN2-type reaction. Therefore, the reaction may occur in a concerted manner, which may avoid the highly energetic hex-2-yl radical as an intermediate. The reaction is associated with a significant primary kinetic isotope effect (kH/kD ≥3) for hydrogen, indicating that the homolytic C-H-bond cleavage is involved in the first irreversible step of the reaction mechanism. The (1-methylalkyl)succinate synthases of n-alkane-utilizing anaerobic bacteria apparently have very broad substrate ranges enabling them to activate not only aliphatic but also alkyl-aromatic hydrocarbons. Thus, two denitrifiers and one sulfate reducer were shown to convert the nongrowth substrate toluene to benzylsuccinate and further to the dead-end product benzoyl-CoA. For this purpose, however, the modified β-oxidation pathway known from alkylbenzene-utilizing bacteria was not employed, but rather the pathway used for n-alkane degradation involving CoA ligation, carbon skeleton rearrangement and decarboxylation. Furthermore, various n-alkane- and alkylbenzene-utilizing denitrifiers and sulfate reducers were found to be capable of forming benzyl alcohols from diverse alkylbenzenes, putatively via dehydrogenases. The thermophilic sulfate reducer strain TD3 forms n-alkylsuccinates during growth with n-alkanes or crude oil, which, based on the observed patterns of homologs, do not derive from a terminal activation of n-alkanes. © 2016 S. Karger AG, Basel.

21 CFR 177.2210 - Ethylene polymer, chloro-sulfonated.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethylene polymer, chloro-sulfonated. 177.2210... (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD ADDITIVES: POLYMERS Substances for Use Only as Components of Articles Intended for Repeated Use § 177.2210 Ethylene polymer, chloro-sulfonated...

21 CFR 177.2210 - Ethylene polymer, chloro-sulfonated.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Ethylene polymer, chloro-sulfonated. 177.2210... (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD ADDITIVES: POLYMERS Substances for Use Only as Components of Articles Intended for Repeated Use § 177.2210 Ethylene polymer, chloro-sulfonated...

21 CFR 177.2210 - Ethylene polymer, chloro-sulfonated.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Ethylene polymer, chloro-sulfonated. 177.2210... (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD ADDITIVES: POLYMERS Substances for Use Only as Components of Articles Intended for Repeated Use § 177.2210 Ethylene polymer, chloro-sulfonated...

21 CFR 177.2210 - Ethylene polymer, chloro-sulfonated.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Ethylene polymer, chloro-sulfonated. 177.2210... (CONTINUED) INDIRECT FOOD ADDITIVES: POLYMERS Substances for Use Only as Components of Articles Intended for Repeated Use § 177.2210 Ethylene polymer, chloro-sulfonated. Ethylene polymer, chlorosulfonated as...

21 CFR 74.1710 - D&C Yellow No. 10.

Code of Federal Regulations, 2010 CFR

2010-04-01

... with phthalic anhydride to give the unsulfonated dye, which is then sulfonated with oleum. (2) Color... water and chloroform, not more than 0.2 percent. Total sulfonated quinaldines, sodium salts, not more than 0.2 percent. Total sulfonated phthalic acids, sodium salts, not more than 0.2 percent. 2-(2...

21 CFR 74.1710 - D&C Yellow No. 10.

Code of Federal Regulations, 2011 CFR

2011-04-01

... with phthalic anhydride to give the unsulfonated dye, which is then sulfonated with oleum. (2) Color... water and chloroform, not more than 0.2 percent. Total sulfonated quinaldines, sodium salts, not more than 0.2 percent. Total sulfonated phthalic acids, sodium salts, not more than 0.2 percent. 2-(2...

40 CFR 721.10045 - Diazotized substituted heteromonocycle coupled with naphthalene sulfonic acid derivative, nickel...

Code of Federal Regulations, 2014 CFR

2014-07-01

... coupled with naphthalene sulfonic acid derivative, nickel complex, alkaline salt (generic). 721.10045... derivative, nickel complex, alkaline salt (generic). (a) Chemical substance and significant new uses subject... heteromonocycle coupled with naphthalene sulfonic acid derivative, nickel complex, alkaline salt (PMN P-02-737) is...

40 CFR 721.10045 - Diazotized substituted heteromonocycle coupled with naphthalene sulfonic acid derivative, nickel...

Code of Federal Regulations, 2011 CFR

2011-07-01

... coupled with naphthalene sulfonic acid derivative, nickel complex, alkaline salt (generic). 721.10045... derivative, nickel complex, alkaline salt (generic). (a) Chemical substance and significant new uses subject... heteromonocycle coupled with naphthalene sulfonic acid derivative, nickel complex, alkaline salt (PMN P-02-737) is...

40 CFR 721.10045 - Diazotized substituted heteromonocycle coupled with naphthalene sulfonic acid derivative, nickel...

Code of Federal Regulations, 2013 CFR

2013-07-01

... coupled with naphthalene sulfonic acid derivative, nickel complex, alkaline salt (generic). 721.10045... derivative, nickel complex, alkaline salt (generic). (a) Chemical substance and significant new uses subject... heteromonocycle coupled with naphthalene sulfonic acid derivative, nickel complex, alkaline salt (PMN P-02-737) is...

40 CFR 721.10045 - Diazotized substituted heteromonocycle coupled with naphthalene sulfonic acid derivative, nickel...

Code of Federal Regulations, 2010 CFR

2010-07-01

... coupled with naphthalene sulfonic acid derivative, nickel complex, alkaline salt (generic). 721.10045... derivative, nickel complex, alkaline salt (generic). (a) Chemical substance and significant new uses subject... heteromonocycle coupled with naphthalene sulfonic acid derivative, nickel complex, alkaline salt (PMN P-02-737) is...

40 CFR 721.10045 - Diazotized substituted heteromonocycle coupled with naphthalene sulfonic acid derivative, nickel...

Code of Federal Regulations, 2012 CFR

2012-07-01

... coupled with naphthalene sulfonic acid derivative, nickel complex, alkaline salt (generic). 721.10045... derivative, nickel complex, alkaline salt (generic). (a) Chemical substance and significant new uses subject... heteromonocycle coupled with naphthalene sulfonic acid derivative, nickel complex, alkaline salt (PMN P-02-737) is...

Spectral study and protein labeling of inclusion complex between dye and calixarene sulfonate.

PubMed

Fei, Xuening; Zhang, Yong; Zhu, Sen; Liu, Lijuan; Yu, Lu

2013-05-01

The host-guest inclusion complex of calix[6]arene sulfonate (SCA6) with thiazole orange (TO) formed in aqueous solution was studied. Absorption and fluorescence techniques were used for the analysis of this inclusion complex. The addition of calixarene sulfonate leads to a decrease in both absorption and fluorescence intensity of the dye, indicating that the inclusion complex was formed. Simultaneously, the inclusion phenomenon of another cyanine dye, Cy3, with calixarene sulfonate was investigated. The stability constant of the two complexes was determined, and the results were compared. The water solubility of TO dye was increased in the presence of calixarene sulfonate, and further protein labeling experiments suggested that this TO-SCA6 complex can act as a fluorescent probe for labeling of biomolecules.

Tumor Uptake And Photodynamic Activity Of Sulfonated Metallo Phthalocyanines

NASA Astrophysics Data System (ADS)

van Lier, Johan E.; Rousseau, Jacques; Paquette, Benoit; Brasseur, N.; Langlois, Rejean; Ali, Hasrat

1989-06-01

Sulfonated metallo phthalocyanines (M-SPC) are extensively studied as sensitizers for photodynamic therapy of cancer. They strongly absorb clinically useful red light with absorption maxima between 670-680 nm. Their photodynamic properties depend on the nature of the central metal ion as well as the degree of substitution on the macrocycle. The zinc, aluminum and gallium complexes are efficient photo-generators of singlet oxygen, the species most likely responsible for their phototoxicity and tumoricidal action. Tissue distribution pattern, cell penetration and dye aggregation are strongly affected by the degree of sulfonation of the dyes. Mono- and disulfonated M-SPC have the highest tendency to form photo-inactive aggregates. However, these lower sulfonated dyes more readily cross cell membranes resulting, in vitro, in enhanced phototoxicity. In vivo, the highly sulfonated hydrophilic M-SPC show the best tumor localization properties but the lower sulfonated dyes still exhibit the best photo-activity. Variations in activities between the differently sulfonated M-SPC are far less pronounced in vivo as compared to in vitro conditions. Such discrepancies are explained by the combined action of numerous vectors including interaction of M-SPC with plasma proteins, vascular versus cellular photo-damage, tumor retention, cell penetration as well as the degree of aggregation of the dye.

Study of sulfonated polyether ether ketone with pendant lithiated fluorinated sulfonic groups as ion conductive binder in lithium-ion batteries

NASA Astrophysics Data System (ADS)

Wei, Zengbin; Xue, Lixin; Nie, Feng; Sheng, Jianfang; Shi, Qianru; Zhao, Xiulan

2014-06-01

In an attempt to reduce the Li+ concentration polarization and electrolyte depletion from the electrode porous space, sulfonated polyether ether ketone with pendant lithiated fluorinated sulfonic groups (SPEEK-FSA-Li) is prepared and attempted as ionic conductivity binder. Sulfonated aromatic poly(ether ether ketone) exhibits strong adhesion and chemical stability, and lithiated fluorinated sulfonic side chains help to enhance the ionic conductivity and Li+ ion diffusion due to the charge delocalization over the sulfonic chain. The performances are evaluated by cyclic voltammetry, electrochemical impedance spectroscopy, charge-discharge cycle testing, 180° peel testing, and compared with the cathode prepared with polyvinylidene fluoride binder. The electrode prepared with SPEEK-FSA-Li binder forms the relatively smaller resistances of both the SEI and the charge transfer of lithium ion transport. This is beneficial to lithium ion intercalation and de-intercalation of the cathode during discharging-charging, therefore the cell prepared with SPEEK-FSA-Li shows lower charge plateau potential and higher discharge plateau potential. Compared with PVDF, the electrode with ionic binder shows smaller decrease in capacity with the increasing of cycle rate. Meanwhile, adhesion strength of electrode prepared with SPEEK-FSA-Li is more than five times greater than that with PVDF.

78 FR 18526 - Significant New Use Rules on Certain Chemical Substances; Technical Amendment

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-27

... aromatic sulfonic acid amino azo dye salts (PMN P-12-276) a typographical error has been identified. This... significant new uses for aromatic sulfonic acid amino azo dye salts, EPA inadvertently listed the respirator... include this requirement when promulgating the significant new uses for aromatic sulfonic acid amino azo...

Structure-matched Phthalocyanine Ion Pair as a Red-emitting Fluorescent Optical Probe for the Analysis of Sodium Dodecylbenzenesulfonate with High Specificity and Sensitivity.

PubMed

Yu, Fei; Guo, Menglin; Deng, Yabin; Lu, Yin; Chen, Lin; Huang, Ping; Li, Donghui

2016-01-01

We have found that a positively charged cationic copper phthalocyanine, Alcian blue (Alcian blue 8GX), can efficiently quench the fluorescence of an oppositely charged red fluorescent phthalocyanine compound with a matched molecular structure, tetrasulfonated aluminum phthalocyanine (AlS4Pc), because of the formation of an ion pair complex (AlS4Pc-Alcian blue 8GX) that exhibits almost no fluorescence. An investigation was carried out on the fluorescence recovery of AlS4Pc-Alcian blue 8GX caused by a series of anionic surfactants containing a sulfonic group (sodium dodecylbenzenesulfonate (SDBS), sodium lauryl sulfate (SLS), and sodium dodecyl sulfate (SDS)). The results showed that SDBS exhibited a significant response, and the highest sensitivity among the surfactants. Due to its high efficiency of fluorescence quenching and the high level of fluorescence recovery, direct observes can even be performed by the naked eye. The results revealed that the Alcian blue 8GX-AlS4Pc ion-pair complex fluorescent probe only responded to SDBS in the low-concentration range. Based on the new founding, this study proposed a novel principle and method of fluorescence enhancement to specifically measure the concentration of SDBS, thereby achieving a highly sensitive and highly specific determination of SDBS. Under the optimal conditions, the fluorescence intensity (I(f)) of the system and the concentration of SDBS in the range of 1 × 10(-7) - 1 × 10(-5) mol/dm(3) exhibited a good linear relationship. This method is highly sensitive, and the operation is simple and rapid. It had been applied for the quantitative analysis of SDBS in environmental water, while achieving satisfactory results compared with those of the standard method. This study developed a new application of the fluorescent phthalocyanine compounds used as molecular probes in analytical sciences.

Cross-linked polyelectrolyte for direct methanol fuel cells applications based on a novel sulfonated cross-linker

NASA Astrophysics Data System (ADS)

Li, Mingyu; Zhang, Gang; Xu, Shuai; Zhao, Chengji; Han, Miaomiao; Zhang, Liyuan; Jiang, Hao; Liu, Zhongguo; Na, Hui

2014-06-01

A novel type of cross-linked proton exchange membrane of lower methanol permeation and high proton conductivity is prepared, based on a newly synthesized sulfonated cross-linker: carboxyl terminated benzimidazole trimer bearing sulfonic acid groups (s-BI). Compared to membranes cross-linked with non-sulfonated cross-linker (BI), SPEEK/s-BI-n membranes show higher IEC values and proton conductivities. Meanwhile, oxidative stability and mechanical property of SPEEK/s-BI-n membranes are obviously improved. Among SPEEK/s-BI-n membranes, SPEEK/s-BI-2 exhibits high proton conductivity, low swelling ratio (0.122 S cm-1 and 15.2% at 60 °C, respectively) and low methanol permeability coefficient. These results imply that the cross-linked membranes prepared with the newly sulfonated cross-linker are promising for the direct methanol fuel cells (DMFCs) application.

Proton conducting sol-gel sulfonated membranes produced from 2-allylphenol, 3-glycidoxypropyl trimethoxysilane and tetraethyl orthosilicate

NASA Astrophysics Data System (ADS)

Mosa, J.; Durán, A.; Aparicio, M.

An important research area in proton exchange membrane fuel cells (PEMFC) is devoted to the development of low cost membranes able to work at temperatures higher than 100 °C. In this work, homogeneous, transparent and crack-free hybrid membranes have been synthesized using tetraethyl orthosilicate (TEOS), 3-glycidoxipropyl trimethoxysilane (GPTMS) and 2-allylphenol (AP) as precursors. The synthesis of proton conducting membranes was performed by a post-sulfonation method using trimethylsilyl chlorosulfonate as a mild sulfonating agent. The water retention properties provided by sulfonate and hydroxyl groups and the high porosity leads to relatively high proton conductivity (maximum values around 1.3 × 10 -3 S cm -1 at 140 °C and 100% RH) for membranes treated at 180 °C and sulfonated for 2 h.

Characteristics of Combined Submerged Membrane Bioreactor with Granular Activated Carbon (GAC) in Treating Lineal Alkylbenzene Sulphonates (LAS) Wastewater

NASA Astrophysics Data System (ADS)

Guo, Jifeng; Xia, Siqing; Lu, Yanjun

2010-11-01

A combined MBR (cMBR) with granular activated carbon (GAC) was used as a backbone system to treat the synthetic lineal alkylbenzene sulphonates (LAS) wastewater. The GAC was added in the MBR to improve the resistance of membrane fouling. A parallel conventional MBR (pMBR) without the GAC was run to give a contrast. The results of the process demonstrate that the cMBR process was more efficient than pMBR. It was found that the TMP changes of the cMBR were slower than the pMBR. The results demonstrated that the cMBRs membrane was better than the pMBR's after a clean period run. It was the GAC scrubbing to the membrane that delayed the membrane fouling of the cMBR. Variable critical flux was found in MBR, which showed that the cMBR could make the critical flux better than pMBR in the run time, but GAC could not improve the critical flux at the end of the period for the severe membrane fouling. Based on this theory, a variable critical flux (J) of MBR was put forward, and the relationship of J with time (t) was: J = 16.081e-0.0177t.

Gas-phase ion-molecule reactions for the identification of the sulfone functionality in protonated analytes in a linear quadrupole ion trap mass spectrometer.

PubMed

Tang, Weijuan; Sheng, Huaming; Kong, John Y; Yerabolu, Ravikiran; Zhu, Hanyu; Max, Joann; Zhang, Minli; Kenttämaa, Hilkka I

2016-06-30

The oxidation of sulfur atoms is an important biotransformation pathway for many sulfur-containing drugs. In order to rapidly identify the sulfone functionality in drug metabolites, a tandem mass spectrometric method based on ion-molecule reactions was developed. A phosphorus-containing reagent, trimethyl phosphite (TMP), was allowed to react with protonated analytes with various functionalities in a linear quadrupole ion trap mass spectrometer. The reaction products and reaction efficiencies were measured. Only protonated sulfone model compounds were found to react with TMP to form a characteristic [TMP adduct-MeOH] product ion. All other protonated compounds investigated, with functionalities such as sulfoxide, N-oxide, hydroxylamino, keto, carboxylic acid, and aliphatic and aromatic amino, only react with TMP via proton transfer and/or addition. The specificity of the reaction was further demonstrated by using a sulfoxide-containing anti-inflammatory drug, sulindac, as well as its metabolite sulindac sulfone. A method based on functional group-selective ion-molecule reactions in a linear quadrupole ion trap mass spectrometer has been demonstrated for the identification of the sulfone functionality in protonated analytes. A characteristic [TMP adduct-MeOH] product ion was only formed for the protonated sulfone analytes. The applicability of the TMP reagent in identifying sulfone functionalities in drug metabolites was also demonstrated. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Synthesis and characterization of mesoporous zirconia and aluminated mesoporous zirconia

NASA Astrophysics Data System (ADS)

Zhao, Elizabeth Sun

Synthesis of mesoporous zirconia has been performed by slowly hydrolyzing zirconium propoxide in the presence of anionic surfactants: namely, dodecyl phosphate or sulfate (P12 and Sf12) and hexadecyl sulfonate (So16) The zirconia. outgassed at 140--150°C has T-plot surface areas higher than 400 M2/g. This outgassing does not remove the surfactant. After calcination in air at 500°C and combustion of the surfactant, the mesoporous volume is reduced by a factor of about 2, whereas the pore wall material crystallizes in the tetragonal phase. The high-resolution electron microscopic study reveals the presence of a disorganized network of polygonal pores structure. It is suggested that the chemistry of the hydrolysis solution is instrumental in determining the pore structure. A schematic model in which the surfactant is a scaffold component is suggested in order to explain these results and the fixation of PO4, or SO4 in the walls may help to preserve the porous structure. It is very different from the templating mechanism. From the density obtained from phase transition temperature, and from the mesoporous volume (N2 adsorption), the thickness of the wall can be calculated as well as the pseudo-length of the pores. From the thickness, the T-plot area can be recalculated and agrees well with the measured T-plot surface area for the sample calcined at 500°C. Around 900°C, the walls become thicker and crystallizes into monoclinic zirconia without pore structure. In order to try to modify, the acidity of the mesoporous sulfated and oxo-phosphated zirconia, they were doped with aluminum. The sulfated zirconia only has a coating layer of amorphous alumina, while the phosphated zirconia has aluminum in the lattice and the alumina coat. A maximum ratio of Al/Zr ˜ 0.04 can be reached in the lattice. The introduction of aluminum into the lattice prevents the crystallization of the oxo-phosphate at 900°C, and helps to preserve the surface area and porosity of the sulfated zirconia above 500°C. However the acidity was not modified by doping. The comparison of the effects of adsorbing water or ammonia on the infrared bands between 1400 and 1000 cm-1 suggests that, besides structural Lewis sites on the surface of ZrO2, the strong Lewis sites are made from chemisorbed SO3. Upon adsorption of water, SO3 is converted, probably, into HSO4 which may act as strong Bronsted sites. At moderate surface hydration, both SO 3 and HSO4, may coexist. The catalytic activity in the isomerization of isobutane is a function of the overall nominal surface density of SO 4. The acid sites on the surface of phosphated mesoporous zirconia are attributable to surface P-OH groups working, as weak Bronsted sites.

40 CFR 721.1637 - 1,2-Propanediol, 3-(2-propenyloxy)-, bis(4-methylbenzene sulfonate); 2-propanol, 1-[2-[[(4...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false 1,2-Propanediol, 3-(2-propenyloxy)-, bis(4-methylbenzene sulfonate); 2-propanol, 1-[2-[[(4-methylphenyl)sulfonyl] oxy]ethoxy]-3-(2...)-, bis(4-methylbenzene sulfonate); 2-propanol, 1-[2-[[(4-methylphenyl)sulfonyl] oxy]ethoxy]-3-(2...

40 CFR 721.1637 - 1,2-Propanediol, 3-(2-propenyloxy)-, bis(4-methylbenzene sulfonate); 2-propanol, 1-[2-[[(4...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false 1,2-Propanediol, 3-(2-propenyloxy)-, bis(4-methylbenzene sulfonate); 2-propanol, 1-[2-[[(4-methylphenyl)sulfonyl] oxy]ethoxy]-3-(2...)-, bis(4-methylbenzene sulfonate); 2-propanol, 1-[2-[[(4-methylphenyl)sulfonyl] oxy]ethoxy]-3-(2...

Synthesis and Properties of Poly(ether sulfone)s with Clustered Sulfonic Groups for PEMFC Applications under Various Relative Humidity.

PubMed

Lee, Shih-Wei; Chen, Jyh-Chien; Wu, Jin-An; Chen, Kuei-Hsien

2017-03-22

Novel sulfonated poly(ether sulfone) copolymers (S4PH-x-PSs) based on a new aromatic diol containing four phenyl substituents at the 2, 2', 6, and 6' positions of 4,4'-diphenyl ether were synthesized. Sulfonation was found to occur exclusively on the 4 position of phenyl substituents by NMR spectroscopy. The ion exchange capacity (IEC) values can be controlled by adjusting the mole percent (x in S4PH-x-PS) of the new diol. The fully hydrated sulfonated poly(ether sulfone) copolymers had good proton conductivity in the range 0.004-0.110 S/cm at room temperature. The surface morphology of S4PH-x-PSs and Nafion 212 was investigated by atomic force microscopy (tapping-mode) and related to the percolation limit and proton conductivity. Single H 2 /O 2 fuel cell based on S4PH-40-PS loaded with 0.25 mg/cm 2 catalyst (Pt/C) exhibited a peak power density of 462.6 mW/cm 2 , which was close to that of Nafion 212 (533.5 mW/cm 2 ) at 80 °C with 80% RH. Furthermore, fuel cell performance of S4PH-35-PS with various relative humidity was investigated. It was confirmed from polarization curves that the fuel cell performance of S4PH-35-PS was not as high as that of Nafion 212 under fully hydrated state due to higher interfacial resistance between S4PH-35-PS and electrodes. While under low relative humidity (53% RH) at 80 °C, fuel cells based on S4PH-35-PS showed higher peak power density (234.9 mW/cm 2 ) than that (214.0 mW/cm 2 ) of Nafion 212.

Randomized Clinical Trial of Sodium Polystyrene Sulfonate for the Treatment of Mild Hyperkalemia in CKD.

PubMed

Lepage, Laurence; Dufour, Anne-Claude; Doiron, Jessica; Handfield, Katia; Desforges, Katherine; Bell, Robert; Vallée, Michel; Savoie, Michel; Perreault, Sylvie; Laurin, Louis-Philippe; Pichette, Vincent; Lafrance, Jean-Philippe

2015-12-07

Hyperkalemia affects up to 10% of patients with CKD. Sodium polystyrene sulfonate has long been prescribed for this condition, although evidence is lacking on its efficacy for the treatment of mild hyperkalemia over several days. This study aimed to evaluate the efficacy of sodium polystyrene sulfonate in the treatment of mild hyperkalemia. In total, 33 outpatients with CKD and mild hyperkalemia (5.0-5.9 mEq/L) in a single teaching hospital were included in this double-blind randomized clinical trial. We randomly assigned these patients to receive either placebo or sodium polystyrene sulfonate of 30 g orally one time per day for 7 days. The primary outcome was the comparison between study groups of the mean difference of serum potassium levels between the day after the last dose of treatment and baseline. The mean duration of treatment was 6.9 days. Sodium polystyrene sulfonate was superior to placebo in the reduction of serum potassium levels (mean difference between groups, -1.04 mEq/L; 95% confidence interval, -1.37 to -0.71). A higher proportion of patients in the sodium polystyrene sulfonate group attained normokalemia at the end of their treatment compared with those in the placebo group, but the difference did not reach statistical significance (73% versus 38%; P=0.07). There was a trend toward higher rates of electrolytic disturbances and an increase in gastrointestinal side effects in the group receiving sodium polystyrene sulfonate. Sodium polystyrene sulfonate was superior to placebo in reducing serum potassium over 7 days in patients with mild hyperkalemia and CKD. Copyright © 2015 by the American Society of Nephrology.

Randomized Clinical Trial of Sodium Polystyrene Sulfonate for the Treatment of Mild Hyperkalemia in CKD

PubMed Central

Lepage, Laurence; Dufour, Anne-Claude; Doiron, Jessica; Handfield, Katia; Desforges, Katherine; Bell, Robert; Vallée, Michel; Savoie, Michel; Perreault, Sylvie; Laurin, Louis-Philippe; Pichette, Vincent

2015-01-01

Background and objectives Hyperkalemia affects up to 10% of patients with CKD. Sodium polystyrene sulfonate has long been prescribed for this condition, although evidence is lacking on its efficacy for the treatment of mild hyperkalemia over several days. This study aimed to evaluate the efficacy of sodium polystyrene sulfonate in the treatment of mild hyperkalemia. Design, setting, participants, & measurements In total, 33 outpatients with CKD and mild hyperkalemia (5.0–5.9 mEq/L) in a single teaching hospital were included in this double–blind randomized clinical trial. We randomly assigned these patients to receive either placebo or sodium polystyrene sulfonate of 30 g orally one time per day for 7 days. The primary outcome was the comparison between study groups of the mean difference of serum potassium levels between the day after the last dose of treatment and baseline. Results The mean duration of treatment was 6.9 days. Sodium polystyrene sulfonate was superior to placebo in the reduction of serum potassium levels (mean difference between groups, −1.04 mEq/L; 95% confidence interval, −1.37 to −0.71). A higher proportion of patients in the sodium polystyrene sulfonate group attained normokalemia at the end of their treatment compared with those in the placebo group, but the difference did not reach statistical significance (73% versus 38%; P=0.07). There was a trend toward higher rates of electrolytic disturbances and an increase in gastrointestinal side effects in the group receiving sodium polystyrene sulfonate. Conclusions Sodium polystyrene sulfonate was superior to placebo in reducing serum potassium over 7 days in patients with mild hyperkalemia and CKD. PMID:26576619

Design, synthesis, and characterization of lightly sulfonated multigraft acrylate-based copolymer superelastomers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Misichronis, Konstantinos; Wang, Weiyu; Cheng, Shiwang

2018-01-29

Multigraft copolymer superelastomers consisting of a poly(n-butyl acrylate) backbone and polystyrene side chains were synthesized and the viscoelastic properties of the non-sulfonated and sulfonated final materials were investigated using extensional rheology (SER3). The non-linear viscoelastic experiments revealed significantly increased true stresses (up to 10 times higher) after sulfonating only 2–3% of the copolymer while the materials maintained high elongation (<700%). The linear viscoelastic experiments showed that the storage and loss modulus are increased by sulfonation and that the copolymers can be readily tuned and further improved by increasing the number of branching points and the molecular weight of the backbone.more » Here, in this way, we show that by tuning not only the molecular characteristics of the multigraft copolymers but also their architecture and chemical interaction, we can acquire thermoplastic superelastomer materials with desired viscoelastic properties.« less

Cyclic Tetrapyrrole Sulfonation, Metals, and Oligomerization in Antiprion Activity▿

PubMed Central

Caughey, Winslow S.; Priola, Suzette A.; Kocisko, David A.; Raymond, Lynne D.; Ward, Anne; Caughey, Byron

2007-01-01

Cyclic tetrapyrroles are among the most potent compounds with activity against transmissible spongiform encephalopathies (TSEs; or prion diseases). Here the effects of differential sulfonation and metal binding to cyclic tetrapyrroles were investigated. Their potencies in inhibiting disease-associated protease-resistant prion protein were compared in several types of TSE-infected cell cultures. In addition, prophylactic antiscrapie activities were determined in scrapie-infected mice. The activity of phthalocyanine was relatively insensitive to the number of peripheral sulfonate groups but varied with the type of metal bound at the center of the molecule. The tendency of the various phthalocyanine sulfonates to oligomerize (i.e., stack) correlated with anti-TSE activity. Notably, aluminum(III) phthalocyanine tetrasulfonate was both the poorest anti-TSE compound and the least prone to oligomerization in aqueous media. Similar comparisons of iron- and manganese-bound porphyrin sulfonates confirmed that stacking ability correlates with anti-TSE activity among cyclic tetrapyrroles. PMID:17709470

Sulfonated Copper Phthalocyanine/Sulfonated Polysulfone Composite Membrane for Ionic Polymer Actuators with High Power Density and Fast Response Time.

PubMed

Kwon, Taehoon; Cho, Hyeongrae; Lee, Jang-Woo; Henkensmeier, Dirk; Kang, Youngjong; Koo, Chong Min

2017-08-30

Ionic polymer composite membranes based on sulfonated poly(arylene ether sulfone) (SPAES) and copper(II) phthalocyanine tetrasulfonic acid (CuPCSA) are assembled into bending ionic polymer actuators. CuPCSA is an organic filler with very high sulfonation degree (IEC = 4.5 mmol H + /g) that can be homogeneously dispersed on the molecular scale into the SPAES membrane, probably due to its good dispersibility in SPAES-containing solutions. SPAES/CuPCSA actuators exhibit larger ion conductivity (102 mS cm -1 ), tensile modulus (208 MPa), strength (101 MPa), and strain (1.21%), exceptionally faster response to electrical stimuli, and larger mechanical power density (3028 W m -3 ) than ever reported for ion-conducting polymer actuators. This outstanding actuation performance of SPAES/CuPCSA composite membrane actuators makes them attractive for next-generation transducers with high power density, which are currently developed, e.g., for underwater propulsion and endoscopic surgery.

Chemical modification of botryosphaeran: structural characterization and anticoagulant activity of a water-soluble sulfonated (1-->3)(1-->6)-β-D-glucan.

PubMed

Brandi, Jamile; Oliveira, Éder C; Monteiro, Nilson; Vasconcelos, Ana Flora D; Dekker, Robert F H; Barbosa, Aneli M; Silveira, Joana L M; Mourão, Paulo A S; Corradi da Silva, Maria de Lourdes

2011-10-01

The exopolysaccharide botryosphaeran (EPS(GLC); a (1--> 3)(1-->6)-β-D-glucan from Botryosphaeria rhodina MAMB- 05) was sulfonated to produce a water-soluble fraction (EPS(GLC)-S) using pyridine and chlorosulfonic acid in formamid. This procedure was then repeated twice to produce another fraction (EPSGLC-RS) with a higher degree of substitution (DS, 1.64). The purity of each botryosphaeran sample (unsulfonated and sulfonated) was assessed by gel filtration chromatography (Sepharose CL-4B), where each polysaccharide was eluted as a single symmetrical peak. The structures of the sulfonated and re-sulfonated botryosphaerans were investigated using ultraviolet-visible (UV-Vis), Fourier-transform infrared (FT-IR), and (13)C nuclear magnetic resonance ((13)C NMR) spectroscopies. EPS(GLC) and EPS(GLC)-RS were also assayed for anticoagulation activity, and EPS(GLC)-RS was identified as an anticoagulant.

Molecular Design of Sulfonated Triblock Copolymer Permselective Membranes

DTIC Science & Technology

2008-07-03

factors governing sorption and permeability ofphosphoorganic agents in PEM made of sulfonated triblock copolymers of styrene and lower olefins by means...membrane morphology at environmental conditions, and the membrane sorption and transport properties with respect to water and nerve gas simulant...and chemical factors governing sorption and permeability of phosphoorganic agents in PEM made of sulfonated triblock copolymers of styrene and lower

40 CFR 721.1630 - 1,2-Ethanediol bis(4-methylbenzenesulfonate); 2,2-oxybis-ethane bis(4-methylbenzenesulfonate...

Code of Federal Regulations, 2011 CFR

2011-07-01

... sulfonate); and ethanol, 2-[1-[[2-[2-[[(4-methylphenyl)sulfonyl] oxy]ethoxy] ethoxy]methyl]-2-(2-propenyloxy... sulfonate); and ethanol, 2-[1-[[2-[2-[[(4-methylphenyl)sulfonyl] oxy]ethoxy] ethoxy]methyl]-2-(2-propenyloxy...,2′-[oxybis(2,1-ethanediyloxy)]bis-, bis(4-methylbenzene-sulfonate) (PMN P-93-1195, CAS no. 19249-03...

40 CFR 721.1630 - 1,2-Ethanediol bis(4-methylbenzenesulfonate); 2,2-oxybis-ethane bis(4-methylbenzenesulfonate...

Code of Federal Regulations, 2010 CFR

2010-07-01

... sulfonate); and ethanol, 2-[1-[[2-[2-[[(4-methylphenyl)sulfonyl] oxy]ethoxy] ethoxy]methyl]-2-(2-propenyloxy... sulfonate); and ethanol, 2-[1-[[2-[2-[[(4-methylphenyl)sulfonyl] oxy]ethoxy] ethoxy]methyl]-2-(2-propenyloxy...,2′-[oxybis(2,1-ethanediyloxy)]bis-, bis(4-methylbenzene-sulfonate) (PMN P-93-1195, CAS no. 19249-03...

Alkyl phosphonic acids and sulfonic acids in the Murchison meteorite

NASA Technical Reports Server (NTRS)

Cooper, George W.; Onwo, Wilfred M.; Cronin, John R.

1992-01-01

Homologous series of alkyl phosphonic acids and alkyl sulfonic acids, along with inorganic orthophosphate and sulfate, are identified in water extracts of the Murchison meteorite after conversion to their t-butyl dimethylsilyl derivatives. The methyl, ethyl, propyl, and butyl compounds are observed in both series. Five of the eight possible alkyl phosphonic acids and seven of the eight possible alkyl sulfonic acids through C4 are identified. Abundances decrease with increasing carbon number as observed of other homologous series indigenous to Murchison. Concentrations range downward from approximately 380 nmol/gram in the alkyl sulfonic acid series, and from 9 nmol/gram in the alkyl phosphonic acid series.

Synthesis and effectiveness of overbased magnesium and calcium petroleum sulfonates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fialkovskii, R.V.; Romanyutina, L.V.; Korbut, L.F.

Overbased sulfonate additives are widely used to improve the service properties of motor oils. This paper describes the preparation of an overbased magnesium sulfonate additive from MSG-8 oil and an investigation of its functional properties. In experiments, the solution of ammonium sulfate, fat diluted with I-20A oil to a 38% concentration, was heated and stirred continuously in the presence of water and excess magnesium oxide for a period of 4 h at 80-120/degree/C while stripping out the liberated ammonia with nitrogen. The resulting oil solution of magnesium sulfonate was dissolved in toluene. The toluene solution after cleanup was held undermore » vacuum to remove the solvent; the residue was an oil solution of overbased magnesium sulfonate. Their properties are tabulated. Comparative data are shown in Table 1 for a calcium sulfonate additive synthesized from the same intermediate (ammonium sulfate), using calcium hydroxide as the base. Test results on M-11 oil containing 5% of the magnesium or calcium additive are listed. It is shown that the magnesium additive gave better results from the calcium additive at the same concentration in terms of oxidation stability, corrosion properties, detergency, and dispersancy. 9 refs.« less

Improvement of electrochemical performances of sulfonated poly(arylene ether sulfone) via incorporation of sulfonated poly(arylene ether benzimidazole)

NASA Astrophysics Data System (ADS)

Hong, Young Taik; Lee, Chang Hyun; Park, Hyung Su; Min, Kyung A.; Kim, Hyung Joong; Nam, Sang Yong; Lee, Young Moo

In the present study, modified acid-base blend membranes were fabricated via incorporation of sulfonated poly(arylene ether benzimidazole) (SPAEBI) into sulfonated poly(arylene ether sulfone) (SPAES). These membranes had excellent methanol-barrier properties in addition to an ability to compensate for the loss of proton conductivity that typically occurs in general acid-base blend system. To fabricate the membranes, SPAEBIs, which served as amphiphilic polymers with different degrees of sulfonation (0-50 mol%), were synthesized by polycondensation and added to SPAES. It resulted in the formation of acid-amphiphilic complexes such as [PAES-SO 3] - +[H-SPAEBI] through the ionic crosslinking, which prevented SO 3H groups in the complex from transporting free protons in an aqueous medium, contributing to a reduction of ion exchange capacity values and water uptake in the blend membranes, and leading to lower methanol permeability in a water-methanol mixture. Unfortunately, the ionic bonding formation was accompanied by a decrease of bound water content and proton conductivity, although the latter problem was solved to some extent by the incorporation of additional SO 3H groups in SPAEBI. In the SPAES-SPAEBI blend membranes, enhancement of proton conductivity and methanol-barrier property was prominent at temperatures over 90 °C. The direct methanol fuel cell (DMFC) performance, which was based on SPAES-SPAEBI-50-5, was 1.2 times higher than that of Nafion ® 117 under the same operating condition.

Synthetic detergents induced-biochemical and histological changes in skin of guinea pigs.

PubMed

Agarwal, C; Mathur, A K; Gupta, B N; Singh, A; Shanker, R

1990-06-01

The linear alkylbenzene sulphonate (LAS) based synthetic detergents-induced decrease in lipid peroxydation and increase in histamine content in exposed skin of guinea pigs in a dose-dependent manner. Histopathological alterations of exposed skin included moderate degree of hyperkeratinization at lower concentration but necrosis, scarring, sloughing as well as discontinuity of epidermis at higher concentrations. The results shows that the contact of skin with detergents causes dermal toxicity.

Electrical and Environmental Studies of Conduction Polymers.

DTIC Science & Technology

1986-01-17

Carbonate), 0.25M Tetrabutylammonium hexafluorophosphate (Bu4 NPF 6 )/THF, and 0.25M Lithium Trifluoromethyl sulfonate (LiCF3 SO 3)frHF. Lithium ...processible polymeric component Other anions commonly used in synthesizing polypyrrole, namely, tetrafluoroborate, hexafluorophosphate rifluoromethyl...are perchlorate (CI0 4 "), tetrafluoroborate (BF 4 "), trifluoromethyl sulfonate (CF3 SO"), hexafluorophosphate (PF6 ") and p-toluene sulfonate (PTS

Use of surfactants for the remediation of contaminated soils: a review.

PubMed

Mao, Xuhui; Jiang, Rui; Xiao, Wei; Yu, Jiaguo

2015-03-21

Due to the great harm caused by soil contamination, there is an increasing interest to apply surfactants to the remediation of a variety of contaminated soils worldwide. This review article summarizes the findings of recent literatures regarding remediation of contaminated soils/sites using surfactants as an enhancing agent. For the surfactant-based remedial technologies, the adsorption behaviors of surfactants onto soil, the solubilizing capability of surfactants, and the toxicity and biocompatibility of surfactants are important considerations. Surfactants can enhance desorption of pollutants from soil, and promote bioremediation of organics by increasing bioavailability of pollutants. The removal of heavy metals and radionuclides from soils involves the mechanisms of dissolution, surfactant-associated complexation, and ionic exchange. In addition to the conventional ionic and nonionic surfactants, gemini surfactants and biosurfactants are also applied to soil remediation due to their benign features like lower critical micelle concentration (CMC) values and better biocompatibility. Mixed surfactant systems and combined use of surfactants with other additives are often adopted to improve the overall performance of soil washing solution for decontamination. Worldwide the field studies and full-scale remediation using surfactant-based technologies are yet limited, however, the already known cases reveal the good prospect of applying surfactant-based technologies to soil remediation. Copyright © 2014 Elsevier B.V. All rights reserved.

Interactions of organic contaminants with mineral-adsorbed surfactants

USGS Publications Warehouse

Zhu, L.; Chen, B.; Tao, S.; Chiou, C.T.

2003-01-01

Sorption of organic contaminants (phenol, p-nitrophenol, and naphthalene) to natural solids (soils and bentonite) with and without myristylpyridinium bromide (MPB) cationic surfactant was studied to provide novel insight to interactions of contaminants with the mineral-adsorbed surfactant. Contaminant sorption coefficients with mineral-adsorbed surfactants, Kss, show a strong dependence on surfactant loading in the solid. At low surfactant levels, the Kss values increased with increasing sorbed surfactant mass, reached a maximum, and then decreased with increasing surfactant loading. The Kss values for contaminants were always higher than respective partition coefficients with surfactant micelles (Kmc) and natural organic matter (Koc). At examined MPB concentrations in water the three organic contaminants showed little solubility enhancement by MPB. At low sorbed-surfactant levels, the resulting mineral-adsorbed surfactant via the cation-exchange process appears to form a thin organic film, which effectively "adsorbs" the contaminants, resulting in very high Kss values. At high surfactant levels, the sorbed surfactant on minerals appears to form a bulklike medium that behaves essentially as a partition phase (rather than an adsorptive surface), with the resulting Kss being significantly decreased and less dependent on the MPB loading. The results provide a reference to the use of surfactants for remediation of contaminated soils/sediments or groundwater in engineered surfactant-enhanced washing.

Vinyl Sulfones as Antiparasitic Agents and a Structural Basis for Drug Design*

PubMed Central

Kerr, Iain D.; Lee, Ji H.; Farady, Christopher J.; Marion, Rachael; Rickert, Mathias; Sajid, Mohammed; Pandey, Kailash C.; Caffrey, Conor R.; Legac, Jennifer; Hansell, Elizabeth; McKerrow, James H.; Craik, Charles S.; Rosenthal, Philip J.; Brinen, Linda S.

2009-01-01

Cysteine proteases of the papain superfamily are implicated in a number of cellular processes and are important virulence factors in the pathogenesis of parasitic disease. These enzymes have therefore emerged as promising targets for antiparasitic drugs. We report the crystal structures of three major parasite cysteine proteases, cruzain, falcipain-3, and the first reported structure of rhodesain, in complex with a class of potent, small molecule, cysteine protease inhibitors, the vinyl sulfones. These data, in conjunction with comparative inhibition kinetics, provide insight into the molecular mechanisms that drive cysteine protease inhibition by vinyl sulfones, the binding specificity of these important proteases and the potential of vinyl sulfones as antiparasitic drugs. PMID:19620707

Hydrophilic modification of polyethersulfone and its membrane characteristics

NASA Astrophysics Data System (ADS)

Liu, Haiju; Huangfu, Feng-yun; Bai, Yundong; Kong, Yuanyuan

2010-07-01

In order to enhance the hydrophilicity of PES, A series of sulfonated polyethersulfone (SPES) were readily prepared via a reaction of sulphonation which used chlorosulfonic as sulfonating agent and concentrated sulfuric acid as solvent. Sulfonation was confirmed by Fourier transform infrared spectroscopy and Thermo gravimetric analyzer. We studied forming film characteristic of SPES by phase diagram. The sulfonated PES materials were then utilized as a hydrophilic modifier for fabrication of SPES membranes. The solvent was NMP and PEG-6000 was pore-forming agent. The characteristics of membranes were studied. It was found that the surface hydrophilicity of the modified PES membranes was remarkably enhanced by contact angle. Water flux was obvious increased and antifouling performance was also improved.

Effect of surfactant types and their concentration on the structural characteristics of nanoclay

NASA Astrophysics Data System (ADS)

Zawrah, M. F.; Khattab, R. M.; Saad, E. M.; Gado, R. A.

2014-03-01

A series of organo-modified nanoclays was synthesized using three different surfactants having different alkyl chain lengths and concentrations [0.5-5.0 cation exchange capacity (CEC)]. These surfactants were Ethanolamine (EA), Cetyltrimethylammoniumbromide (CTAB) and Tetraoctadecylammoniumbromide (TO). The obtained modified nanoclays were characterized by X-ray diffraction (XRD), Fourier Transform Infrared spectroscopy (FTIR) and Scanning electron microscopy (SEM) and compared with unmodified nanoclay. The results of XRD analysis indicated that the basal d-spacing has increased with increasing alkyl chain length and surfactant concentration. From the obtained microstructures of these organo-modified nanoclays, the mechanism of surfactant adsorption was proposed. At relatively low loading of surfactant, most of surfactant entered the spacing by an ion-exchange mechanism and is adsorbed onto the interlayer cation sites. When the concentration of the surfactant exceeds the CEC of clay, the surfactant molecules then adhere to the surface adsorbed surfactant. Some surfactants entered the interlayers, whereas the others were attached to the clay surface. When the concentration of surfactant increased further beyond 2.0 CEC, the surfactants might occupy the inter-particle space within the house-of-cards aggregate structure.

The influence of chain rigidity and the degree of sulfonation on the morphology of block copolymers as nano reactor

NASA Astrophysics Data System (ADS)

Hong, K.; Zhang, X.

2005-03-01

Polyelectrolyte block copolymer was used to form an ordered domain of ionic block as a ``nanoreactor'' due to its ability to bind oppositely charged metal ion, Zn^2+, Fe^2+ etc. The purpose of our research is to investigate the controllability of the size and morphology of domains (inorganic nano particles) by changing backbone stiffness, the charge density and the volume fraction of ionic block. Poly(styrene sulfonate) (PSS), which backbone is flexible, and poly(cyclohexadiene sulfonate) (PCHDS), which backbone is ``semiflexible'', were used as ionic blocks. We synthesized PtBS-PSS and PS-PCHDS with various degree of sulfonation and the volume fraction. Zinc oxide (ZnO) nano particles successfully formed in the ionic domain of microphase separated block copolymers. We used SANS to characterize the morphology of block copolymers and TEM for block copolymer containing ZnO nano particles. Our experimental results show that the chemistry of ``sulfonation'' of block copolymers can be successfully used to synthesize nano composite materials.

Improvement of neutral oil quality in the production of sulfonate additives

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhurba, A.S.; Bludilin, V.M.; Antonov, V.N.

This paper is concerned with improvement of neutral oil used as materials for sulfonation to produce additives for lubricating oils. In this article the authors analyze the basic reasons for the unsatisfactory quality of the neutral oil and attempt to define the ways in which the process technology can be improved so as to produce neutral oil with the required composition, at the same time raising the efficiency of utilization of the MSG-8 oil used as a feedstock for this process. Experimental results are presented which demonstrate the feasibility of sulfonating neutral oil in the high-speed mixer under near-optimal conditions.more » The yield of sulfonic acid approaches the theoretical yield. With the lowest contents of aromatic hydrocarbons in the original neutral oil, the aromatic hydrocarbons are almost completely converted to sulfonic acids. The yield of neutral oil is sufficiently high, and the residual content of aromatic hydrocarbons in the oil is no greater than 3%.« less

Antibacterial surface modified of novel nanocomposite sulfonated polyethersulfone/polyrhodanine membrane

NASA Astrophysics Data System (ADS)

Rostam, Abbas Babaei; Peyravi, Majid; Ghorbani, Mohsen; Jahanshahi, Mohsen

2018-01-01

In this study, sulfonated-polyethersulfone/polyrhodanine (SPES/PRh) membranes with antibacterial behavior were fabricated. Polyethersulfone (PES) sulfonation was performed to enhance its hydrophilicity and next polyrhodanine nanoparticles (PRhNPs) were synthesized along with the sulfonated PES (SPES) by polyrhodanine (PRh) in situ polymerization. The sulfonation step also helps making composite membrane due to development of probable bondings and polymers engagements. The constructed membranes characterization was performed by FTIR, FESEM, contact angle, 1H NMR, TGA and EDS analyses. SPES/PRh membrane had enhanced hydrophilicity and consequently better fluxes for aqueous solutions. The composite SPES/PRh membrane flux was improved to 139/78 L/m2 h comparing 58.21 L/m2 h for SPES one. Membrane operational performances, antibacterial and antibiofouling tests showed improved flux, better rejection and appropriate antibacterial and antibiofouling properties for SPES/PRh membrane. The 100% bacteria mortality for specified concentrations and appropriate inhibition zones up to 9 mm have been achieved. It is generally a suitable membrane to provide proper performance beside antibacterial and antibiofouling behavior.

Molecular and morphological characterization of midblock-sulfonated styrenic triblock copolymers

DOE PAGES

Mineart, Kenneth P.; Ryan, Justin J.; Lee, Byeongdu; ...

2017-01-11

Midblock-sulfonated triblock copolymers afford a desirable opportunity to generate network-forming amphiphilic materials that are suitable for use in a wide range of emerging technologies as fuel-cell, water-desalination, ion-exchange, photovoltaic, or electroactive membranes. Employing a previously reported synthetic strategy wherein poly( p- tert-butylstyrene) remains unreactive, we have selectively sulfonated the styrenic midblock of a poly( p- tert-butylstyrene- b-styrene- b- p- tert- butylstyrene) (TST) triblock copolymer to different extents. Comparison of the resulting sulfonated copolymers with results from our prior study provides favorable quantitative agreement and suggests that a shortened reaction time is advantageous. An ongoing challenge regarding the morphological development ofmore » charged block copolymers is the competition between microphase separation of the incompatible blocks and physical cross-linking of ionic clusters, with the latter often hindering the former. Here, we expose the sulfonated TST copolymers to solvent-vapor annealing to promote nanostructural refinement. Furthermore, the effect of such annealing on morphological characteristics, as well as on molecular free volume, is explored.« less

Color reduction of sulfonated eucalyptus kraft lignin.

PubMed

Zhang, Hui; Bai, Youcan; Zhou, Wanpeng; Chen, Fangeng

2017-04-01

Several eucalyptus lignins named as HSL, SML and BSL were prepared by high temperature sulfonation, sulfomethylation, butane sultone sulfonation respectively. The color properties of samples were investigated. Under optimized conditions the sulfonic group (SO 3 H) content of HSL, SML and BSL reached 1.52, 1.60 and 1.58mmol/g, respectively. Samples were characterized by UV-vis spectroscopy, FTIR spectroscopy, 1 H NMR spectroscopy, GPC and brightness test, respectively. The results revealed that BSL performed a higher molecular weight and lighter color due to the phenolic hydroxyl blocking by 1,4-butane sultone (1,4-BS). The color reduction of sodium borohydride treated BSL (labeled as SBSL) was further enhanced and the brightness value was improved by 76.1% compared with the darkest HSL. SBSL process was much better than HSL and SML process. Hydroxyl blocking effect of 1,4-BS and reducibility of sodium borohydride played important roles in the color reduction of sulfonated eucalyptus kraft lignin. Copyright © 2017 Elsevier B.V. All rights reserved.

Morphology and Proton Transport in Sulfonated Block Copolymer and Mesoporous Polymer Electrolyte Membranes

NASA Astrophysics Data System (ADS)

Chen, Chelsea; Wong, David; Beers, Keith; Balsara, Nitash

2013-03-01

In an effort to understand the fundamentals of proton transport in polymer electrolyte membranes (PEMs), we have developed a series of poly(styrene-b-ethylene-b-styrene) (SES) membranes. The SES membranes were subsequently sulfonated to yield proton conducting S-SES membranes. We examine the effects of sulfonation level, temperature and thermal history on the morphology of S-SES membranes in both dry and hydrated states. The effects of these parameters on water uptake and proton transport characteristics of the membranes are also examined. Furthermore, building upon the strategy we deployed in sulfonating the SES membranes, we fabricated mesoporous S-SES membranes, with pores lined up with the proton conducting channels. These membranes have three distinct phases: structural block, proton-conducting block, and void. We examine the effects of pore size, domain structure and sulfonation level on water uptake and proton conductivity of the mesoporous PEMs at different temperatures. This work is funded by Department of Energy.

Methylsulfonylmethane

MedlinePlus

... Dimethyl Sulfone MSM, DMSO2, Methyl Sulfone, Methyl Sulfonyl Methane, Methyl Sulphonyl Methane, Méthyle Sulfonyle Méthane, Méthyle Sulphonyle Méthane, Méthylsulfonylméthane, Metilsulfonilmentano, ...

Pulmonary surfactant for neonatal respiratory disorders.

PubMed

Merrill, Jeffrey D; Ballard, Roberta A

2003-04-01

Surfactant therapy has revolutionized neonatal care and is used routinely for preterm infants with respiratory distress syndrome. Recent investigation has further elucidated the function of surfactant-associated proteins and their contribution toward surfactant and lung immune defense functions. As the field of neonatology moves away from intubation and mechanical ventilation of preterm infants at birth toward more aggressive use of nasal continuous positive airway pressure, the optimal timing of exogenous surfactant therapy remains unclear. Evidence suggests that preterm neonates with bronchopulmonary dysplasia and prolonged mechanical ventilation also experience surfactant dysfunction; however, exogenous surfactant therapy beyond the first week of life has not been well studied. Surfactant replacement therapy has been studied for use in other respiratory disorders, including meconium aspiration syndrome and pneumonia. Commercial surfactant preparations currently available are not optimal, given the variability of surfactant protein content and their susceptibility to inhibition. Further progress in the treatment of neonatal respiratory disorders may include the development of "designer" surfactant preparations.

Pyrolytic carbon black composite and method of making the same

DOEpatents

Naskar, Amit K.; Paranthaman, Mariappan Parans; Bi, Zhonghe

2016-09-13

A method of recovering carbon black includes the step of providing a carbonaceous source material containing carbon black. The carbonaceous source material is contacted with a sulfonation bath to produce a sulfonated material. The sulfonated material is pyrolyzed to produce a carbon black containing product comprising a glassy carbon matrix phase having carbon black dispersed therein. A method of making a battery electrode is also disclosed.

Enhanced antifouling and antibacterial properties of poly (ether sulfone) membrane modified through blending with sulfonated poly (aryl ether sulfone) and copper nanoparticles

NASA Astrophysics Data System (ADS)

Zhang, Jingjing; Xu, Ya'nan; Chen, Shouwen; Li, Jiansheng; Han, Weiqing; Sun, Xiuyun; Wu, Dihua; Hu, Zhaoxia; Wang, Lianjun

2018-03-01

A series of novel blend ultrafiltration (UF) membranes have been successfully prepared from commercial poly (ether sulfone), lab-synthesized sulfonated poly (aryl ether sulfone) (SPAES, 1 wt%) and copper nanoparticles (0 ∼ 0.4 wt%) via immersion precipitation phase conversion. The micro-structure and separation performance of the membranes were characterized by field emission scanning electron microscopy (SEM) and cross-flow filtration experiments, respectively. Sodium alginate, bovine serum albumin and humic acid were chosen as model organic foulants to investigate the antifouling properties, while E. coil was used to evaluate the antibacterial property of the fabricated membranes. By the incorporation with SPAES and copper nanoparticles, the hydrophilicity, antifouling and antibacterial properties of the modified UF membranes have been profoundly improved. At a copper nanoparticles content of 0.4 wt%, the PES/SPAES/nCu(0.4) membrane exhibited a high pure water flux of 193.0 kg/m2 h, reaching the smallest contact angle of 52°, highest flux recovery ratio of 79% and largest antibacterial rate of 78.9%. Furthermore, the stability of copper nanoparticles inside the membrane matrix was also considerably enhanced, the copper nanoparticles were less than 0.08 mg/L in the effluent during the whole operation.

Enhanced proton conductivity of proton exchange membranes by incorporating sulfonated metal-organic frameworks

NASA Astrophysics Data System (ADS)

Li, Zhen; He, Guangwei; Zhao, Yuning; Cao, Ying; Wu, Hong; Li, Yifan; Jiang, Zhongyi

2014-09-01

In this study, octahedral crystal MIL101(Cr) with a uniform size of ∼400 nm is synthesized via hydrothermal reaction. It is then functionalized with sulfonic acid groups by concentrated sulfuric acid and trifluoromethanesulfonic anhydride in nitromethane. The sulfonated MIL101(Cr) are homogeneously incorporated into sulfonated poly(ether ether ketone) (SPEEK) matrix to prepare hybrid membranes. The performances of hybrid membranes are evaluated by proton conductivity, methanol permeability, water uptake and swelling property, and thermal stability. The methanol permeability increased slightly from 6.12 × 10-7 to 7.39 × 10-7 cm2 s-1 with the filler contents increasing from 0 to 10 wt. %. However, the proton conductivity of the hybrid membranes increased significantly. The proton conductivity is increased up to 0.306 S cm-1 at 75 °C and 100% RH, which is 96.2% higher than that of pristine membranes (0.156 S cm-1). The increment of proton conductivity is attributed to the following multiple functionalities of the sulfonated MIL101(Cr) in hybrid membranes: i) providing sulfonic acid groups as facile proton hopping sites; ii) forming additional proton-transport pathways at the interfaces of polymer and MOFs; iii) constructing hydrogen-bonded networks for proton conduction via -OH provided by the hydrolysis of coordinatively unsaturated metal sites.

Investigation of sulfonated polysulfone membranes as electrolyte in a passive-mode direct methanol fuel cell mini-stack

NASA Astrophysics Data System (ADS)

Lufrano, F.; Baglio, V.; Staiti, P.; Stassi, A.; Aricò, A. S.; Antonucci, V.

This paper reports on the development of polymer electrolyte membranes (PEMs) based on sulfonated polysulfone for application in a DMFC mini-stack operating at room temperature in passive mode. The sulfonated polysulfone (SPSf) with two degrees of sulfonation (57 and 66%) was synthesized by a well-known sulfonation process. SPSf membranes with different thicknesses were prepared and investigated. These membranes were characterized in terms of methanol/water uptake, proton conductivity, and fuel cell performance in a DMFC single cell and mini-stack operating at room temperature. The study addressed (a) control of the synthesis of sulfonated polysulfone, (b) optimization of the assembling procedure, (c) a short lifetime investigation and (d) a comparison of DMFC performance in active-mode operation vs. passive-mode operation. The best passive DMFC performance was 220 mW (average cell power density of about 19 mW cm -2), obtained with a thin SPSf membrane (70 μm) at room temperature, whereas the performance of the same membrane-based DMFC in active mode was 38 mW cm -2. The conductivity of this membrane, SPSf (IEC = 1.34 mequiv. g -1) was 2.8 × 10 -2 S cm -1. A preliminary short-term test (200 min) showed good stability during chrono-amperometry measurements.

Toward High-Performance Lithium-Sulfur Batteries: Upcycling of LDPE Plastic into Sulfonated Carbon Scaffold via Microwave-Promoted Sulfonation.

PubMed

Kim, Patrick J; Fontecha, Harif D; Kim, Kyungho; Pol, Vilas G

2018-05-02

Lithium-sulfur batteries were intensively explored during the last few decades as next-generation batteries owing to their high energy density (2600 Wh kg -1 ) and effective cost benefit. However, systemic challenges, mainly associated with polysulfide shuttling effect and low Coulombic efficiency, plague the practical utilization of sulfur cathode electrodes in the battery market. To address the aforementioned issues, many approaches have been investigated by tailoring the surface characteristics and porosities of carbon scaffold. In this study, we first present an effective strategy of preparing porous sulfonated carbon (PSC) from low-density polyethylene (LDPE) plastic via microwave-promoted sulfonation. Microwave process not only boosts the sulfonation reaction of LDPE but also induces huge amounts of pores within the sulfonated LDPE plastic. When a PSC layer was utilized as an interlayer in lithium-sulfur batteries, the sulfur cathode delivered an improved capacity of 776 mAh g -1 at 0.5C and an excellent cycle retention of 79% over 200 cycles. These are mainly attributed to two materialistic benefits of PSC: (a) porous structure with high surface area and (b) negatively charged conductive scaffold. These two characteristics not only facilitate the improved electrochemical kinetics but also effectively block the diffusion of polysulfides via Coulomb interaction.

Differential fipronil susceptibility and metabolism in two rice stem borers from China.

PubMed

Fang, Qi; Huang, Cheng-Hua; Ye, Gong-Yin; Yao, Hong-Wei; Cheng, Jia-An; Akhtar, Zunnu-Raen

2008-08-01

The susceptibilities of larvae of two rice stem borers, namely, Chilo suppressalis (Walker) (Lepidoptera: Crambidae) and Sesamia inferens (Walker) (Lepidoptera: Nocutidae) to fipronil and its metabolites were investigated, and then the activities of microsomal O-demethylase, and glutathione transferase (GST) in two species were measured. The metabolism of fipronil in both stem borers was determined in vivo and in vitro. The LD50 value of fipronil to S. inferens was 118.5-fold higher than that of C. suppressalis. The bioassay results offipronil metabolites showed that the toxicities of sulfone and sulfide were higher than fipronil for both species, and the differential toxicity between sulfone and fipronil was remarkable. Alternatively, the activities of microsomal O-demethylase and GST of C. suppressalis were 1.35- and 2.06-fold higher than S. inferens, respectively. The in vivo and in vitro studies on metabolism of fipronil showed that all of fipronil, sulfone, and sulfide were detected and the content of sulfone was higher than sulfide in both stem borers. The residue of sulfone in C. suppressalis was significantly higher than that in S. inferens. These results suggest that the higher activity of mixed function oxidases may cause the higher capacity of C. suppressalis to produce fipronil-sulfone, which is more toxic than fipronil leading to the higher susceptibility of this species.

Comparison of rSP-C surfactant with natural and synthetic surfactants after late treatment in a rat model of the acute respiratory distress syndrome

PubMed Central

Häfner, Dietrich; Germann, Paul-Georg; Hauschke, Dieter

1998-01-01

In a previous paper we showed that an SP-C containing surfactant preparation has similar activity as bovine-derived surfactants in a rat lung lavage model of the adult respiratory distress syndrome. In this study surfactant was given ten minutes after the last lavage (early treatment). In the present investigation we were interested how different surfactant preparations behave when they are administered 1 h after the last lavage (late treatment). Four protein containing surfactants (rSP-C surfactant, bLES, Infasurf and Survanta) were compared with three protein-free surfactants (ALEC, Exosurf and the phospholipid (PL) mixture of the rSP-C surfactant termed PL surfactant) with respect to their ability to improve gas exchange in this more stringent model when surfactant is given one hour after the last lavage. For better comparison of the surfactants the doses were related to phospholipids. The surfactants were given at doses of 25, 50 and 100 mg kg−1 body weight. The surfactants were compared to an untreated control group that was only ventilated for the whole experimental period. Tracheotomized rats (8–12 per dose and surfactant) were pressure-controlled ventilated (Siemens Servo Ventilator 900C) with 100% oxygen at a respiratory rate of 30 breaths min−1, inspiration expiration ratio of 1 : 2, peak inspiratory pressure of 28 cmH2O at positive endexpiratory pressure (PEEP) of 8 cmH2O. Animals were ventilated for one hour after the last lavage and thereafter the surfactants were intratracheally instilled. During the whole experimental period the ventilation was not changed. Partial arterial oxygen pressures (PaO2, mmHg) at 30 min and 120 min after treatment were used for statistical comparison. All protein containing surfactants caused a dose-dependent increase of the reduced PaO2 values at 30 min after treatment. The protein-free surfactants showed only weak dose-dependent increase in PaO2 values at this time. This difference between the protein-containing and the protein-free surfactants was even more pronounced when comparing the PaO2 values at 120 min after treatment. Only rSP-C surfactant, bLES and Infasurf showed a dose-dependent increase in PaO2 at this time. With this animal model of late treatment it is possible even to differentiate between bovine derived surfactants. The differences between protein-containing and protein-free surfactants become even more pronounced. From the comparison of rSP-C surfactant with bovine-derived surfactants and the PL surfactant without rSP-C, it can be concluded that addition of rSP-C is sufficient to achieve the same activity as that of natural surfactants. PMID:9720777

Inactivation of a class A and a class C β-lactamase by 6β-(hydroxymethyl)penicillanic acid sulfone

PubMed Central

Papp-Wallace, Krisztina M.; Bethel, Christopher R.; Gootz, Thomas D.; Shang, Wenchi; Stroh, Justin; Lau, William; McLeod, Dale; Price, Loren; Marfat, Anthony; Distler, Anne; Drawz, Sarah M.; Chen, Hansong; Harry, Emily; Nottingham, Micheal; Carey, Paul R.; Buynak, John D.; Bonomo, Robert A.

2012-01-01

β-Lactamase inhibitors (clavulanic acid, sulbactam, and tazobactam) contribute significantly to the longevity of the β-lactam antibiotics used to treat serious infections. In the quest to design more potent compounds and to understand the mechanism of action of known inhibitors, 6β-(hydroxymethyl)penicillanic acid sulfone (6β-HM-sulfone) was tested against isolates expressing the class A TEM-1 β-lactamase and a clinically important variant of the AmpC cephalosporinase of Pseudomonas aeruginosa, PDC-3. The addition of the 6β-HM-sulfone inhibitor to ampicillin was highly effective. 6β-HM-sulfone inhibited TEM-1 with an IC50 of 12 ± 2 nM and PDC-3 with an IC50 of 180 ± 36 nM, and displayed lower partition ratios than commercial inhibitors, with partition ratios (kcat/kinact) equal to 174 for TEM-1 and 4 for PDC-3. Measured for 20 h, 6β-HM-sulfone demonstrated rapid, first-order inactivation kinetics with the extent of inactivation being related to the concentration of inhibitor for both TEM-1 and PDC-3. Using mass spectrometry to gain insight into the intermediates of inactivation of this inhibitor, 6β-HM-sulfone was found to form a major adduct of +247 ± 5 Da with TEM-1 and +245 ± 5 Da with PDC-3, suggesting that the covalently bound, hydrolytically stabilized acyl-enzyme has lost a molecule of water (H–O–H). Minor adducts of +88 ± 5 Da with TEM-1 and +85 ± 5 Da with PDC-3 revealed that fragmentation of the covalent adduct can result but appeared to occur slowly with both enzymes. 6β-HM-sulfone is an effective and versatile β-lactamase inhibitor of representative class A and C enzymes. PMID:22155308

Concentration-dependent toxicity effect of SDBS on swimming behavior of freshwater fishes.

PubMed

Zhang, Ying; Ma, Jing; Zhou, Siyun; Ma, Fang

2015-07-01

Sodium dodecyl benzene sulfonate (SDBS) is a kind of widely used anionic surfactant and its discharge may pose potential risk to the receiving aquatic ecosystem. The aim of our study is to investigate the toxic effect of SDBS on fish swimming behavior quantitatively, followed by examination whether there are significant differences of swimming behavior among applied fish species (i.e. zebra fish (Danio rerio), Japanese medaka (Oryzias latipes) and red carp (Cyprinus carpio)). The swimming speed and vertical position were analyzed after the fish exposed to SDBS aiming to reflect the toxicity of SDBS on fish. Our results showed that the swimming behavior of three fishes was significantly affected by SDBS, although there were slight differences of swimming pattern changes among three fish species when they exposed to the same concentration of SDBS. It could be seen that red carp, one of the native fish species in China, can be used as a model fish to reflect the water quality changes as well as zebra fish and Japanese medaka which are commonly used as model fishes. Our study also illustrated that the swimming behavior monitoring may have a good application prospect in pre-warning of water quality. Copyright © 2015 Elsevier B.V. All rights reserved.

Effect of Montmorillonite Nanogel Composite Fillers on the Protection Performance of Epoxy Coatings on Steel Pipelines.

PubMed

Atta, Ayman M; El-Saeed, Ashraf M; Al-Lohedan, Hamad A; Wahby, Mohamed

2017-06-02

Montmorillonite (MMT) clay mineral is widely used as filler for several organic coatings. Its activity is increased by exfoliation via chemical modification to produce nanomaterials. In the present work, the modification of MMT to form nanogel composites is proposed to increase the dispersion of MMT into epoxy matrices used to fill cracks and holes produced by the curing exotherms of epoxy resins. The dispersion of MMT in epoxy improved both the mechanical and anti-corrosion performance of epoxy coatings in aggressive marine environments. In this respect, the MMT surfaces were chemically modified with different types of 2-acrylamido-2-methyl propane sulfonic acid (AMPS) nanogels using a surfactant-free dispersion polymerization technique. The effect of the chemical structure, nanogel content and the interaction with MMT surfaces on the surface morphology, surface charges and dispersion in the epoxy matrix were investigated for use as nano-filler for epoxy coatings. The modified MMT nanogel epoxy composites showed excellent resistance to mechanical damage and salt spray resistance up to 1000 h. The interaction of MMT nanogel composites with the epoxy matrix and good response of AMPS nanogel to sea water improve their ability to act as self-healing materials for epoxy coatings for steel.

Micelle-enhanced and terbium-sensitized spectrofluorimetric determination of gatifloxacin and its interaction mechanism

NASA Astrophysics Data System (ADS)

Guo, Changchuan; Wang, Lei; Hou, Zhun; Jiang, Wei; Sang, Lihong

2009-05-01

A terbium-sensitized spectrofluorimetric method using an anionic surfactant, sodium dodecyl benzene sulfonate (SDBS), was developed for the determination of gatifloxacin (GFLX). A coordination complex system of GFLX-Tb 3+-SDBS was studied. It was found that SDBS significantly enhanced the fluorescence intensity of the complex (about 11-fold). Optimal experimental conditions were determined as follows: excitation and emission wavelengths of 331 and 547 nm, pH 7.0, 2.0 × 10 -4 mol l -1 terbium (III), and 2.0 × 10 -4 mol l -1 SDBS. The enhanced fluorescence intensity of the system (Δ If) showed a good linear relationship with the concentration of GFLX over the range of 5.0 × 10 -10 to 5.0 × 10 -8 mol l -1 with a correlation coefficient of 0.9996. The detection limit (3 σ) was determined as 6.0 × 10 -11 mol l -1. This method has been successfully applied to the determination of GFLX in pharmaceuticals and human urine/serum samples. Compared with most of other methods reported, the rapid and simple procedure proposed in the text offers higher sensitivity, wider linear range, and better stability. The interaction mechanism of the system is also studied by the research of ultraviolet absorption spectra, surface tension, solution polarity and fluorescence polarization.

Adaptation to low body temperature influences pulmonary surfactant composition thereby increasing fluidity while maintaining appropriately ordered membrane structure and surface activity.

PubMed

Suri, Lakshmi N M; McCaig, Lynda; Picardi, Maria V; Ospina, Olga L; Veldhuizen, Ruud A W; Staples, James F; Possmayer, Fred; Yao, Li-Juan; Perez-Gil, Jesus; Orgeig, Sandra

2012-07-01

The interfacial surface tension of the lung is regulated by phospholipid-rich pulmonary surfactant films. Small changes in temperature affect surfactant structure and function in vitro. We compared the compositional, thermodynamic and functional properties of surfactant from hibernating and summer-active 13-lined ground squirrels (Ictidomys tridecemlineatus) with porcine surfactant to understand structure-function relationships in surfactant membranes and films. Hibernating squirrels had more surfactant large aggregates with more fluid monounsaturated molecular species than summer-active animals. The latter had more unsaturated species than porcine surfactant. Cold-adapted surfactant membranes displayed gel-to-fluid transitions at lower phase transition temperatures with reduced enthalpy. Both hibernating and summer-active squirrel surfactants exhibited lower enthalpy than porcine surfactant. LAURDAN fluorescence and DPH anisotropy revealed that surfactant bilayers from both groups of squirrels possessed similar ordered phase characteristics at low temperatures. While ground squirrel surfactants functioned well during dynamic cycling at 3, 25, and 37 degrees C, porcine surfactant demonstrated poorer activity at 3 degrees C but was superior at 37 degrees C. Consequently the surfactant composition of ground squirrels confers a greater thermal flexibility relative to homeothermic mammals, while retaining tight lipid packing at low body temperatures. This may represent the most critical feature contributing to sustained stability of the respiratory interface at low lung volumes. Thus, while less effective than porcine surfactant at 37 degrees C, summer-active surfactant functions adequately at both 37 degrees C and 3 degrees C allowing these animals to enter hibernation. Here further compositional alterations occur which improve function at low temperatures by maintaining adequate stability at low lung volumes and when temperature increases during arousal from hibernation.

Synthesis and Characterization of Hydrophilic-Hydrophobic Poly(Arylene Ether Sulfone) Random and Segmented Copolymers for Membrane Applications

NASA Astrophysics Data System (ADS)

Nebipasagil, Ali

Poly(arylene ether sulfone)s are high-performance engineering thermoplastics that have been investigated extensively over the past several decades due to their outstanding mechanical properties, high glass transition temperatures (Tg), solvent resistance and exceptional thermal, oxidative and hydrolytic stability. Their thermal and mechanical properties are highly suited to a variety of applications including membrane applications such as reverse osmosis, ultrafiltration, and gas separation. This dissertation covers structure-property-performance relationships of poly(arylene ether sulfone) and poly(ethylene oxide)-containing random and segmented copolymers for reverse osmosis and gas separation membranes. The second chapter of this dissertation describes synthesis of disulfonated poly(arylene ether sulfone) random copolymers with oligomeric molecular weights that contain hydrophilic and hydrophobic segments for thin film composite (TFC) reverse osmosis membranes. These copolymers were synthesized and chemically modified to obtain novel crosslinkable poly(arylene ether sulfone) oligomers with acrylamide groups on both ends. The acrylamideterminated oligomers were crosslinked with UV radiation in the presence of a multifunctional acrylate and a UV initiator. Transparent, dense films were obtained with high gel fractions. Mechanically robust TFC membranes were prepared from either aqueous or water-methanol solutions cast onto a commercial UDELRTM foam support. This was the first example that utilized a water or alcohol solvent system and UV radiation to obtain reverse osmosis TFC membranes. The membranes were characterized with regard to composition, surface properties, and water uptake. Water and salt transport properties were elucidated at the department of chemical engineering at the University of Texas at Austin. The gas separation membranes presented in chapter three were poly(arylene ether sulfone) and poly(ethylene oxide) (PEO)-containing polyurethanes. Poly(arylene ether sulfone) copolymers with controlled molecular weights were synthesized and chemically modified to obtain poly(arylene ether sulfone) polyols with aliphatic hydroxyethyl terminal functionality. The hydroxyethyl-terminated oligomers and a,u-hydroxy-terminated PEO were chain extended with a diisocyanate to obtain polyurethanes. Compositions with high poly(arylene ether sulfone) content relative to the hydrophilic PEO blocks were of interest due to their mechanical integrity. The membranes were characterized to analyze their compositions, thermal and mechanical properties, water uptake, and molecular weights. These membranes were also evaluated by collaborators at the University of Texas at Austin to explore single gas transport properties. The results showed that both polymer and transport properties closely related to PEO-content. The CO2/CH4 gas selectivity of our membranes were improved from 25 to 34 and the CO2/N2 gas selectivity nearly doubled from 25 to 46 by increasing PEO-content from 0 to 30 wt.% in polyurethanes. Chapter four also focuses on polymers for gas separation membranes. Disulfonated poly(arylene ether sulfone) and poly(ethylene oxide)-containing polyurethanes were synthesized for potential applications as gas separation membranes. Disulfonated polyols containing 20 and 40 mole percent of disulfonated repeat units with controlled molecular weights were synthesized. Poly(arylene ether sulfone) polyols and alpha,o-hydroxy-terminated poly(ethylene oxide) were subsequently chain extended with a diisocyanate to obtain polyurethanes. Thermal and mechanical characterization revealed that the polyurethanes had a phase-mixed complex morphology.

Premicellar and micelle formation behavior of dye surfactant ion pairs in aqueous solutions: deprotonation of dye in ion pair micelles.

PubMed

Gohain, Biren; Dutta, Robin K

2008-07-15

The premicellar and micelle formation behavior of dye surfactant ion pairs in aqueous solutions monitored by surface tension and spectroscopic measurements has been described. The measurements have been made for three anionic sulfonephthalein dyes and cationic surfactants of different chain lengths, head groups, and counterions. The observations have been attributed to the formation of closely packed dye surfactant ion pairs which is similar to nonionic surfactants in very dilute concentrations of the surfactant. These ion pairs dominate in the monolayer at the air-water interface of the aqueous dye surfactant solutions below the CMC of the pure surfactant. It has been shown that the dye in the ion pair deprotonates on micelle formation by the ion pair surfactants at near CMC but submicellar surfactant concentrations. The results of an equilibrium study at varying pH agree with the model of deprotonated 1:1 dye-surfactant ion pair formation in the near CMC submicellar solutions. At concentrations above the CMC of the cationic surfactant the dye is solubilized in normal micelles and the monolayer at the air-water interface consists of the cationic surfactant alone even in the presence of the dyes.

VOLATILIZATION OF ALKYLBENZENES FROM WATER.

USGS Publications Warehouse

Rathbun, R.E.; Tai, D.Y.

1985-01-01

Volatilization is a physical process of importance in determining the fate of many organic compounds in streams and rivers. This process is frequently described by the conceptual-two-film model. The model assumes uniformly mixed water and air phases separated by thin films of water and air in which mass transfer is by molecular diffusion. Mass-transfer coefficients for the water and air films are related to an overall mass-transfer coefficient for volatilization through the Henry's law constant.

Fungal biocatalysts in the biofiltration of VOC-polluted air.

PubMed

Kennes, Christian; Veiga, María C

2004-09-30

Gas-phase biofilters used for the treatment of waste gases were originally packed with compost or other natural filter beds containing indigenous microorganisms. Over the past decade much effort has been made to develop new carrier materials, more performant biocatalysts and new types of bioreactors. Elimination capacities reached nowadays are 5 to 10 times higher than those originally reported with conventional compost biofilters. With the recently developed inert filter beds, inoculation is a prerequisite for successful start-up and operation. Either non-defined mixed cultures or pure bacterial cultures have originally been used. The search for efficient fungal biocatalysts started only a few years ago, mainly for the biofiltration of waste gases containing hydrophobic compounds, such as styrene, alpha-pinene, benzene, or alkylbenzenes. In this review, recently isolated new fungal strains able to degrade alkylbenzenes and other related volatile organic pollutants are described, as well as their major characteristics and their use as biocatalysts in gas-phase biofilters for air pollution control. In biofiltration, the most extensively studied organism belongs to the genus Exophiala, although strains of Scedosporium, Paecilomyces, Cladosporium, Cladophialophora, and white-rot fungi are all potential candidates for use in biofilters. Encouraging results were obtained in most of the cases in which some of those organisms were present in gas-phase biofilters. They allow reaching high elimination capacities and are resistant to low pH values and to reduce moisture content.

Anaerobic Oxidation of o-Xylene, m-Xylene, and Homologous Alkylbenzenes by New Types of Sulfate-Reducing Bacteria

PubMed Central

Harms, Gerda; Zengler, Karsten; Rabus, Ralf; Aeckersberg, Frank; Minz, Dror; Rosselló-Mora, Ramon; Widdel, Friedrich

1999-01-01

Various alkylbenzenes were depleted during growth of an anaerobic, sulfate-reducing enrichment culture with crude oil as the only source of organic substrates. From this culture, two new types of mesophilic, rod-shaped sulfate-reducing bacteria, strains oXyS1 and mXyS1, were isolated with o-xylene and m-xylene, respectively, as organic substrates. Sequence analyses of 16S rRNA genes revealed that the isolates affiliated with known completely oxidizing sulfate-reducing bacteria of the δ subclass of the class Proteobacteria. Strain oXyS1 showed the highest similarities to Desulfobacterium cetonicum and Desulfosarcina variabilis (similarity values, 98.4 and 98.7%, respectively). Strain mXyS1 was less closely related to known species, the closest relative being Desulfococcus multivorans (similarity value, 86.9%). Complete mineralization of o-xylene and m-xylene was demonstrated in quantitative growth experiments. Strain oXyS1 was able to utilize toluene, o-ethyltoluene, benzoate, and o-methylbenzoate in addition to o-xylene. Strain mXyS1 oxidized toluene, m-ethyltoluene, m-isoproyltoluene, benzoate, and m-methylbenzoate in addition to m-xylene. Strain oXyS1 did not utilize m-alkyltoluenes, whereas strain mXyS1 did not utilize o-alkyltoluenes. Like the enrichment culture, both isolates grew anaerobically on crude oil with concomitant reduction of sulfate to sulfide. PMID:10049854

Kinetic studies of amino acid-based surfactant binding to DNA.

PubMed

Santhiya, Deenan; Dias, Rita S; Dutta, Sounak; Das, Prasanta Kumar; Miguel, Maria G; Lindman, Björn; Maiti, Souvik

2012-05-24

In this work, the binding kinetics of amino acid-based surfactants, presenting different linkers and head groups, with calf thymus (CT)-DNA was studied using stopped-flow fluorescence spectroscopy. The kinetic studies were carried out as a function of Na(+) concentration and surfactant-to-DNA charge ratio. The surfactant binding on DNA took place in two consecutive steps, for which the corresponding first and second relative rate constants (k(1) and k(2)) were determined. The fast step was attributed to the surfactant binding to DNA and micelle formation in its vicinity, the slower step to DNA condensation and possible rearrangement of the surfactant aggregates. In general, both relative rate constants increase with surfactant concentration and decrease with the ionic strength of the medium. The architecture of the surfactant was found to have a significant impact on the kinetics of the DNA-surfactant complexation. Surfactants with amide linkers showed larger relative rate constants than those with ester linkers. The variation of the relative rate constants with the head groups of the surfactants, alanine and proline, was found to be less obvious, being partially dependent on the surfactant concentration.

Oxidatively stable fluorinated sulfone electrolytes for high voltage high energy lithium-ion batteries

DOE PAGES

Su, Chi -Cheung; He, Meinan; Redfern, Paul C.; ...

2017-03-16

New fluorinated sulfones were synthesized and evaluated in high voltage lithium-ion batteries using LiNi 0.5Mn 1.5O 4 (LNMO) cathode. Fluorinated sulfones with an α-trifluoromethyl group exhibit enhanced oxidation stability, reduced viscosity and superior separator wettability as compared to their non-fluorinated counterparts. Finally, the improved performance in high voltage cells makes it a promising high voltage electrolyte for 5-V lithium-ion chemistry.

Corrosion prevention of cold rolled steel using water dispersible lignosulfonic acid doped polyaniline

NASA Technical Reports Server (NTRS)

Viswanathan, Tito (Inventor)

2007-01-01

The invention provides coatings useful for preventing corrosion of metals. The coatings comprise a film-forming resin and conductive polymers comprising linearly conjugated .pi.-systems and residues of sulfonated lignin or a sulfonated polyflavonoid or derivatives of solfonated lignin or a sulfonated polyflavonoid. The invention also provides a latex formulation of the coatings, and articles of manufacture comprising a metal substrate and a coating in contact with the metal substrate.

Corrosion Prevention of Cold Rolled Steel Using Water Dispersible Lignosulfonic Acid Doped Polyaniline

NASA Technical Reports Server (NTRS)

Viswanathan, Tito (Inventor)

2007-01-01

The invention provides coatings useful for preventing corrosion of metals. The coatings comprise a film-forming resin and conductive polymers comprising linearly conjugated x-systems and residues of sulfonated lignin or a sulfonated polyflavonoid or derivatives of solfonated lignin or a sulfonated polyflavonoid. The invention also provides a latex formulation of the coatings, and articles of manufacture comprising a metal substrate and a coating in contact with the metal substrate.

Polyarylether composition and membrane

DOEpatents

Hung, Joyce; Brunelle, Daniel Joseph; Harmon, Marianne Elisabeth; Moore, David Roger; Stone, Joshua James; Zhou, Hongyi; Suriano, Joseph Anthony

2010-11-09

A composition including a polyarylether copolymer is provided. The copolymer includes a polyarylether backbone; and a sulfonated oligomeric group bonded to the polyarylether suitable for use as a cation conducting membrane. Method of bonding a sulfonated oligomeric group to the polyarylether backbone to form a polyarylether copolymer. The membrane may be formed from the polyarylether copolymer composition. The chain length of the sulfonated oligomeric group may be controlled to affect or control the ion conductivity of the membrane.

Toxicity of pyrolysis gases from synthetic polymers

NASA Technical Reports Server (NTRS)

Hilado, C. J.; Soriano, J. A.; Kosola, K. L.; Kourtides, D. A.; Parker, J. A.

1977-01-01

The screening test method was used to investigate toxicity in polyethylene, polystyrene, polymethyl methacrylate, polyaryl sulfone, polyether sulfone, polyphenyl sulfone, and polyphenylene sulfide. Changing from a rising temperature program to a fixed temperature program resulted on shorter times to animal responses. This effect was attributed in part to more rapid generation of toxicants. The toxicants from the sulfur containing polymers appeared to act more rapidly than the toxicants from the other polymers. It was not known whether this effect was due primarily to difference in concentration or in the nature of the toxicants. The carbon monoxide concentration found did not account for the results observed with the sulfur containing polymers. Polyphenyl sulfone appeared to exhibit the least toxicity among the sulfur containing polymers evaluated under these test conditions.

Polymerization reactivity of sulfomethylated alkali lignin modified with horseradish peroxidase.

PubMed

Yang, Dongjie; Wu, Xiaolei; Qiu, Xueqing; Chang, Yaqi; Lou, Hongming

2014-03-01

Alkali lignin (AL) was employed as raw materials in the present study. Sulfomethylation was conducted to improve the solubility of AL, while sulfomethylated alkali lignin (SAL) was further polymerized by horseradish peroxidase (HRP). HRP modification caused a significant increase in molecular weight of SAL which was over 20 times. It was also found to increase the amount of sulfonic and carboxyl groups while decrease the amount of phenolic and methoxyl groups in SAL. The adsorption quantity of self-assembled SAL film was improved after HRP modification. Sulfonation and HRP modification were mutually promoted. The polymerization reactivity of SAL in HRP modification was increased with its sulfonation degree. Meanwhile, HRP modification facilitated SAL's radical-sulfonation reaction. Copyright © 2014. Published by Elsevier Ltd.

The Detection of Surfactant Proteins A, B, C and D in the Human Brain and Their Regulation in Cerebral Infarction, Autoimmune Conditions and Infections of the CNS

PubMed Central

Schob, Stefan; Schicht, Martin; Sel, Saadettin; Stiller, Dankwart; Kekulé, Alexander; Paulsen, Friedrich; Maronde, Erik; Bräuer, Lars

2013-01-01

Surfactant proteins (SP) have been studied intensively in the respiratory system. Surfactant protein A and surfactant protein D are proteins belonging to the family of collectins each playing a major role in the innate immune system. The ability of surfactant protein A and surfactant protein D to bind various pathogens and facilitate their elimination has been described in a vast number of studies. Surfactant proteins are very important in modulating the host's inflammatory response and participate in the clearance of apoptotic cells. Surfactant protein B and surfactant protein C are proteins responsible for lowering the surface tension in the lungs. The aim of this study was an investigation of expression of surfactant proteins in the central nervous system to assess their specific distribution patterns. The second aim was to quantify surfactant proteins in cerebrospinal fluid of healthy subjects compared to patients suffering from different neuropathologies. The expression of mRNA for the surfactant proteins was analyzed with RT-PCR done with samples from different parts of the human brain. The production of the surfactant proteins in the brain was verified using immunohistochemistry and Western blot. The concentrations of the surfactant proteins in cerebrospinal fluid from healthy subjects and patients suffering from neuropathologic conditions were quantified using ELISA. Our results revealed that surfactant proteins are present in the central nervous system and that the concentrations of one or more surfactant proteins in healthy subjects differed significantly from those of patients affected by central autoimmune processes, CNS infections or cerebral infarction. Based on the localization of the surfactant proteins in the brain, their different levels in normal versus pathologic samples of cerebrospinal fluid and their well-known functions in the lungs, it appears that the surfactant proteins may play roles in host defense of the brain, facilitation of cerebrospinal fluid secretion and maintenance of the latter's rheological properties. PMID:24098648

Repeat surfactant therapy for postsurfactant slump.

PubMed

Katz, L A; Klein, J M

2006-07-01

To evaluate repeat surfactant therapy for the treatment of respiratory failure associated with postsurfactant slump in extremely low birth weight infants (ELBW) by characterizing the population of premature infants who develop postsurfactant slump and measuring their response to a secondary course of surfactant therapy. A retrospective analysis of a cohort of all patients admitted over a 3-year period with birth weights <1000 g (ELBW infants). Information was collected by chart review and the patients were categorized into three distinct groups for analysis. Initial surfactant only, patients who received surfactant replacement therapy only for respiratory distress syndrome (RDS); repeat surfactant, patients who received both initial surfactant replacement for RDS and repeat surfactant therapy for postsurfactant slump (defined as respiratory failure after 6 days of age), and no surfactant, patients in whom no surfactant was ever administered. A respiratory severity score (RSS) was used to measure the severity of lung disease and response to surfactant therapy. Over 3 years, there were 165 ELBW infants who could develop postsurfactant slump and be eligible for repeat surfactant therapy. There were 39 infants who never received any surfactant therapy estimated gestational age (EGA) 27.7 +/- 1.7, birth weight 856 +/- 109 g) either at birth or after 6 days of life. There were 126 patients treated for RDS with initial surfactant replacement therapy (EGA 25.6 +/- 1.9 weeks, birth weight 713 +/- 179 g). Out of these RDS patients, 101 improved with an initial course of surfactant therapy (EGA 26 +/- 1.8, birth weight 751 +/- 143 g), but 25 (20% of the patients with RDS) developed postsurfactant slump and received a repeat course of surfactant therapy (EGA 24.7 +/- 1.2, birth weight 647 +/- 120 g). The repeat surfactant group (postsurfactant slump) was significantly more premature and had significantly lower birth weights compared to both the initial surfactant only group and the no surfactant ever group. Logistic regression analysis revealed that lack of antenatal steroids, earlier gestational age, and the receiving of 2 or more doses of surfactant to treat the initial RDS were significantly associated with receiving repeat surfactant therapy for postsurfactant slump. Of the 25 patients treated with a repeat course of surfactant therapy more than 70% of patients (n = 18) had an improvement in their lung disease with a 15% reduction in their RSS. This improvement was significant at all time points evaluated (12, 24, and 48 h). We found that a repeat course of surfactant therapy, after day of life 6, led to a significant improvement in hypoxemic respiratory failure in premature infants with postsurfactant slump. Infants who received repeat surfactant therapy were born at a significantly earlier gestational age, had significantly smaller birth weight and had significantly worse lung disease. They were significantly less likely to have received antenatal steroids and were significantly more likely to have received multiple doses of surfactant to treat their initial RDS. A repeat course of surfactant therapy for patients with postsurfactant slump appeared beneficial in the short-term. These initial findings would support performing randomized control trials of repeat surfactant therapy for postsurfactant slump.

Copolymers of fluorinated polydienes and sulfonated polystyrene

DOEpatents

Mays, Jimmy W [Knoxville, TN; Gido, Samuel P [Hadley, MA; Huang, Tianzi [Knoxville, TN; Hong, Kunlun [Knoxville, TN

2009-11-17

Copolymers of fluorinated polydienes and sulfonated polystyrene and their use in fuel cell membranes, batteries, breathable chemical-biological protective materials, and templates for sol-gel polymerization.

Reactions of Phenolphthalein at Various pH Values.

ERIC Educational Resources Information Center

Wittke, Georg

1983-01-01

Reactions of phenolphthalein with sodium hydroxide and sulfuric are discussed. Also discusses the sulfonation of phenolphthalein, listing experimental results related to the sulfonation reaction. (JN)

Surfactant for Pediatric Acute Lung Injury

PubMed Central

Willson, Douglas F.; Chess, Patricia R.; Notter, Robert H.

2008-01-01

Synopsis This article reviews exogenous surfactant therapy and its use in mitigating acute lung injury (ALI) and the acute respiratory distress syndrome (ARDS) in infants, children, and adults. Biophysical and animal research documenting surfactant dysfunction in ALI/ARDS is described, and the scientific rationale for treatment with exogenous surfactant is discussed. Major emphasis is on reviewing clinical studies of surfactant therapy in pediatric and adult patients with ALI/ARDS. Particular advantages from surfactant therapy in direct pulmonary forms of these syndromes are described. Also discussed are additional factors affecting the efficacy of exogenous surfactants in ALI/ARDS, including the multifaceted pathology of inflammatory lung injury, the effectiveness of surfactant delivery in injured lungs, and composition-based activity differences among clinical exogenous surfactant preparations. PMID:18501754

Surfactant Based Enhanced Oil Recovery and Foam Mobility Control

DOE Office of Scientific and Technical Information (OSTI.GOV)

George J. Hirasaki; Clarence A. Miller

Surfactant flooding has the potential to significantly increase recovery over that of conventional waterflooding. The availability of a large number of surfactant structures makes it possible to conduct a systematic study of the relation between surfactant structure and its efficacy for oil recovery. A mixture of two surfactants was found to be particularly effective for application in carbonate formations at low temperature. The mixture is single phase for higher salinity or calcium concentrations than that for either surfactant used alone. This makes it possible to inject the surfactant slug with polymer close to optimal conditions and yet be single phase.more » A formulation has been designed for a particular field application. It uses partially hydrolyzed polyacrylamide for mobility control. The addition of an alkali such as sodium carbonate makes possible in situ generation of naphthenic soap and significant reduction of synthetic surfactant adsorption. The design of the process to maximize the region of ultra-low IFT takes advantage of the observation that the ratio of soap to synthetic surfactant is a parameter in the conditions for optimal salinity. Even for a fixed ratio of soap to surfactant, the range of salinity for low IFT was wider than that reported for surfactant systems in the literature. Low temperature, forced displacement experiments in dolomite and silica sandpacks demonstrate that greater than 95% recovery of the waterflood remaining oil is possible with 0.2% surfactant concentration, 0.5 PV surfactant slug, with no alcohol. Compositional simulation of the displacement process demonstrates the role of soap/surfactant ratio on passage of the profile through the ultralow IFT region, the importance of a wide salinity range of low IFT, and the importance of the viscosity of the surfactant slug. Mobility control is essential for surfactant EOR. Foam is evaluated to improve the sweep efficiency of surfactant injected into fractured reservoirs as well as a drive fluid for ASP flooding. UTCHEM is a reservoir simulator specially designed for surfactant EOR. It has been modified to represent the effects of a change in wettability produced by surfactant injection.« less

Effect of surfactants on sorption of atrazine by soil

NASA Astrophysics Data System (ADS)

Abu-Zreig, Majed; Rudra, R. P.; Dickinson, W. T.; Evans, L. J.

1999-03-01

This study investigates the effect of synthetic wastewater containing surfactants on the sorption of atrazine using an equilibrium batch technique. Laboratory experiments were conducted on three soils with two non-ionic (Rexol and Rexonic) surfactants and one anionic (Sulphonic) surfactant, specifically manufactured for the detergent industry. Four sets of experiments were conducted to examine the influence of surfactants on the equilibrium time of atrazine sorption, to explore the effect of surfactant concentration, pH and type of surfactant on the amount of atrazine sorbed and to determine sorption isotherms of atrazine in the presence of surfactants. The results indicate that the application of Sulphonic results in dramatic increase in the adsorption of atrazine on to soils, the increase being directly proportional to the concentration of the surfactant. Application of the Sulphonic surfactants with a concentration of 3000 mg/l can result in a significant increase in Kd values of atrazine for loam and sandy loam soils. On the other hand, the effect of non-ionic surfactants depends on their concentration. Generally, non-ionic surfactants can result in a slight increase in atrazine sorption at high concentration, an exception being Rexol on sandy loam soil. At low concentrations, non-ionic surfactants have shown a tendency to decrease atrazine sorption.

Effects of added surfactant on swelling and molecular transport in drug-loaded tablets based on hydrophobically modified poly(acrylic acid).

PubMed

Knöös, Patrik; Wahlgren, Marie; Topgaard, Daniel; Ulvenlund, Stefan; Piculell, Lennart

2014-08-14

A combination of NMR chemical shift imaging and self-diffusion experiments is shown to give a detailed molecular picture of the events that occur when tablets of hydrophobically modified poly(acrylic acid) loaded with a drug (griseofulvin) swell in water in the presence or absence of surfactant (sodium octylbenzenesulfonate). The hydrophobic substituents on the polymer bind and trap the surfactant molecules in mixed micelles, leading to a slow effective surfactant transport that occurs via a small fraction of individually dissolved surfactant molecules in the water domain. Because of the efficient binding of surfactant, the penetrating water is found to diffuse past the penetrating surfactant into the polymer matrix, pushing the surfactant front outward as the matrix swells. The added surfactant has little effect on the transport of drug because both undissolved solid drug and surfactant-solubilized drug function as reservoirs that essentially follow the polymer as it swells. However, the added surfactant nevertheless has a strong indirect effect on the release of griseofulvin, through the effect of the surfactant on the solubility and erosion of the polymer matrix. The surfactant effectively solubilizes the hydrophobically modified polymer, making it fully miscible with water, leading to a more pronounced swelling and a slower erosion of the polymer matrix.

Tuning of protein-surfactant interaction to modify the resultant structure.

PubMed

Mehan, Sumit; Aswal, Vinod K; Kohlbrecher, Joachim

2015-09-01

Small-angle neutron scattering and dynamic light scattering studies have been carried out to examine the interaction of bovine serum albumin (BSA) protein with different surfactants under varying solution conditions. We show that the interaction of anionic BSA protein (pH7) with surfactant and the resultant structure are strongly modified by the charge head group of the surfactant, ionic strength of the solution, and mixed surfactants. The protein-surfactant interaction is maximum when two components are oppositely charged, followed by components being similarly charged through the site-specific binding, and no interaction in the case of a nonionic surfactant. This interaction of protein with ionic surfactants is characterized by the fractal structure representing a bead-necklace structure of micellelike clusters adsorbed along the unfolded protein chain. The interaction is enhanced with ionic strength only in the case of site-specific binding of an anionic surfactant with an anionic protein, whereas it is almost unchanged for other complexes of cationic and nonionic surfactants with anionic proteins. Interestingly, the interaction of BSA protein with ionic surfactants is significantly suppressed in the presence of nonionic surfactant. These results with mixed surfactants thus can be used to fold back the unfolded protein as well as to prevent surfactant-induced protein unfolding. For different solution conditions, the results are interpreted in terms of a change in fractal dimension, the overall size of the protein-surfactant complex, and the number of micelles attached to the protein. The interplay of electrostatic and hydrophobic interactions is found to govern the resultant structure of complexes.

Tuning of protein-surfactant interaction to modify the resultant structure

NASA Astrophysics Data System (ADS)

Mehan, Sumit; Aswal, Vinod K.; Kohlbrecher, Joachim

2015-09-01

Small-angle neutron scattering and dynamic light scattering studies have been carried out to examine the interaction of bovine serum albumin (BSA) protein with different surfactants under varying solution conditions. We show that the interaction of anionic BSA protein (p H 7 ) with surfactant and the resultant structure are strongly modified by the charge head group of the surfactant, ionic strength of the solution, and mixed surfactants. The protein-surfactant interaction is maximum when two components are oppositely charged, followed by components being similarly charged through the site-specific binding, and no interaction in the case of a nonionic surfactant. This interaction of protein with ionic surfactants is characterized by the fractal structure representing a bead-necklace structure of micellelike clusters adsorbed along the unfolded protein chain. The interaction is enhanced with ionic strength only in the case of site-specific binding of an anionic surfactant with an anionic protein, whereas it is almost unchanged for other complexes of cationic and nonionic surfactants with anionic proteins. Interestingly, the interaction of BSA protein with ionic surfactants is significantly suppressed in the presence of nonionic surfactant. These results with mixed surfactants thus can be used to fold back the unfolded protein as well as to prevent surfactant-induced protein unfolding. For different solution conditions, the results are interpreted in terms of a change in fractal dimension, the overall size of the protein-surfactant complex, and the number of micelles attached to the protein. The interplay of electrostatic and hydrophobic interactions is found to govern the resultant structure of complexes.

Acid monolayer functionalized iron oxide nanoparticle catalysts

NASA Astrophysics Data System (ADS)

Ikenberry, Myles

Superparamagnetic iron oxide nanoparticle functionalization is an area of intensely active research, with applications across disciplines such as biomedical science and heterogeneous catalysis. This work demonstrates the functionalization of iron oxide nanoparticles with a quasi-monolayer of 11-sulfoundecanoic acid, 10-phosphono-1-decanesulfonic acid, and 11-aminoundecanoic acid. The carboxylic and phosphonic moieties form bonds to the iron oxide particle core, while the sulfonic acid groups face outward where they are available for catalysis. The particles were characterized by thermogravimetric analysis (TGA), transmission electron microscopy (TEM), potentiometric titration, diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), inductively coupled plasma optical emission spectrometry (ICP-OES), X-ray photoelectron spectrometry (XPS), and dynamic light scattering (DLS). The sulfonic acid functionalized particles were used to catalyze the hydrolysis of sucrose at 80° and starch at 130°, showing a higher activity per acid site than the traditional solid acid catalyst Amberlyst-15, and comparing well against results reported in the literature for sulfonic acid functionalized mesoporous silicas. In sucrose catalysis reactions, the phosphonic-sulfonic nanoparticles (PSNPs) were seen to be incompletely recovered by an external magnetic field, while the carboxylic-sulfonic nanoparticles (CSNPs) showed a trend of increasing activity over the first four recycle runs. Between the two sulfonic ligands, the phosphonates produced a more tightly packed monolayer, which corresponded to a higher sulfonic acid loading, lower agglomeration, lower recoverability through application of an external magnetic field, and higher activity per acid site for the hydrolysis of starch. Functionalizations with 11-aminoundecanoic acid resulted in some amine groups binding to the surfaces of iron oxide nanoparticles. This amine binding is commonly ignored in iron oxide nanoparticle syntheses and functionalizations for biomedical and catalytic applications, affecting understandings of surface charge and other material properties.

Liquid-liquid phase separation in dilute solutions of poly(styrene sulfonate) with multivalent cations: Phase diagrams, chain morphology, and impact of temperature

NASA Astrophysics Data System (ADS)

Hansch, Markus; Hämisch, Benjamin; Schweins, Ralf; Prévost, Sylvain; Huber, Klaus

2018-01-01

The dilute solution behavior of sodium poly(styrene sulfonate) is studied in the presence of trivalent Al3+ and bivalent Ba2+ cations at various levels of excess NaCl. The study evaluates the phase behavior and the morphology of the polyelectrolyte chains with increasing extent of decoration with the Al3+ and Ba2+ cations and analyses the effect of temperature on these decorated chains. The phase behavior is presented in the form of the cation concentration versus the respective poly(styrene sulfonate) concentration, recorded at the onset of precipitation. Whereas poly(styrene sulfonate) with Al3+ exhibits a linear phase boundary, denoted as the "threshold line," which increases with increasing poly(styrene sulfonate) concentration, Ba2+ cations show a threshold line which is independent of the poly(styrene sulfonate) concentration. An additional re-entrant phase, at considerably higher cation content than those of the threshold lines, is observed with Al3+ cations but not with Ba2+ cations. The threshold line and the re-entrant phase boundary form parts of the liquid-liquid phase boundary observed at the limit of low polymer concentration. The dimensions of the polyelectrolyte chains shrink considerably while approaching the respective threshold lines on increase of the Al3+ and Ba2+ cation content. However, subtle differences occur between the morphological transformation induced by Al3+ and Ba2+. Most strikingly, coils decorated with Al3+ respond very differently to temperature variations than coils decorated with Ba2+ do. As the temperature increases, the poly(styrene sulfonate) chains decrease their size in the presence of Al3+ cations but increase in size in the presence of Ba2+ cations.

Unique role of ionic liquid [bmin][BF 4] during curcumin-surfactant association and micellization of cationic, anionic and non-ionic surfactant solutions

NASA Astrophysics Data System (ADS)

Patra, Digambara; Barakat, Christelle

2011-09-01

Hydrophilic ionic liquid, 1-butyl-3-methylimidazolium tetrafluoroburate, modified the properties of aqueous surfactant solutions associated with curcumin. Because of potential pharmaceutical applications as an antioxidant, anti-inflammatory and anti-carcinogenic agent, curcumin has received ample attention as potential drug. The interaction of curcumin with various charged aqueous surfactant solutions showed it exists in deprotonated enol form in surfactant solutions. The nitro and hydroxyl groups of o-nitrophenol interact with the carbonyl and hydroxyl groups of the enol form of curcumin by forming ground state complex through hydrogen bonds and offered interesting information about the nature of the interactions between the aqueous surfactant solutions and curcumin depending on charge of head group of the surfactant. IL[bmin][BF 4] encouraged early formation of micelle in case of cationic and anionic aqueous surfactant solutions, but slightly prolonged micelle formation in the case of neutral aqueous surfactant solution. However, for curcumin IL [bmin][BF 4] favored strong association (7-fold increase) with neutral surfactant solution, marginally supported association with anionic surfactant solution and discouraged (˜2-fold decrease) association with cationic surfactant solution.

Silica micro- and nanoparticles reduce the toxicity of surfactant solutions.

PubMed

Ríos, Francisco; Fernández-Arteaga, Alejandro; Fernández-Serrano, Mercedes; Jurado, Encarnación; Lechuga, Manuela

2018-04-20

In this work, the toxicity of hydrophilic fumed silica micro- and nanoparticles of various sizes (7 nm, 12 nm, and 50 μm) was evaluated using the luminescent bacteria Vibrio fischeri. In addition, the toxicity of an anionic surfactant solution (ether carboxylic acid), a nonionic surfactant solution (alkyl polyglucoside), and a binary (1:1) mixture of these solutions all containing these silica particles was evaluated. Furthermore, this work discusses the adsorption of surfactants onto particle surfaces and evaluates the effects of silica particles on the surface tension and critical micellar concentration (CMC) of these anionic and nonionic surfactants. It was determined that silica particles can be considered as non-toxic and that silica particles reduce the toxicity of surfactant solutions. Nevertheless, the toxicity reduction depends on the ionic character of the surfactants. Differences can be explained by the different adsorption behavior of surfactants onto the particle surface, which is weaker for nonionic surfactants than for anionic surfactants. Regarding the effects on surface tension, it was found that silica particles increased the surface activity of anionic surfactants and considerably reduced their CMC, whereas in the case of nonionic surfactants, the effects were reversed. Copyright © 2018 Elsevier B.V. All rights reserved.

An enantioselective approach to the preparation of chiral sulfones by Ir-catalyzed asymmetric hydrogenation.

PubMed

Peters, Byron K; Zhou, Taigang; Rujirawanich, Janjira; Cadu, Alban; Singh, Thishana; Rabten, Wangchuk; Kerdphon, Sutthichat; Andersson, Pher G

2014-11-26

Several chiral sulfonyl compounds were prepared using the iridium catalyzed asymmetric hydrogenation reaction. Vinylic, allylic and homoallylic sulfone substitutions were investigated, and high enantioselectivity is maintained regardless of the location of the olefin with respect to the sulfone. Impressive stereoselectivity was obtained for dialkyl substitutions, which typically are challenging substrates in the hydrogenation. As expected, the more bulky Z-substrates were hydrogenated slower than the corresponding E isomers, and in slightly lower enantioselectivity.

Crystal structure of zwitterionic bisimidazolium sulfonates

NASA Astrophysics Data System (ADS)

Kohmoto, Shigeo; Okuyama, Shinpei; Yokota, Nobuyuki; Takahashi, Masahiro; Kishikawa, Keiki; Masu, Hyuma; Azumaya, Isao

2012-05-01

Crystal structures of three zwitterionic bisimidazolium salts 1-3 in which imidazolium sulfonate moieties were connected with aromatic linkers, p-xylylene, 4,4'-dimethylenebiphenyl, and phenylene, respectively, were examined. The latter two were obtained as hydrates. An S-shaped molecular structure in which the sulfonate moiety was placed on the imidazolium ring was observed for 1. A helical array of hydrated water molecules was obtained for 2 while a linear array of hydrated water molecules was observed for 3.

Arylsulfatase B Mediates the Sulfonation-Transport Interplay in Human Embryonic Kidney 293 Cells Overexpressing Sulfotransferase 1A3.

PubMed

Zhao, Mengjing; Wang, Shuai; Li, Feng; Dong, Dong; Wu, Baojian

2016-09-01

Elucidating the intricate relationships between metabolic and transport pathways contributes to improved predictions of in vivo drug disposition and drug-drug interactions. Here we reported that inhibited excretion of conjugative metabolites [i.e., hesperetin 3'-O-sulfate (H3'S) and hesperetin 7-O-sulfate (H7S)] by MK-571 led to reduced metabolism of hesperetin (a maximal 78% reduction) in human embryonic kidney 293 cells overexpressing sulfotransferase 1A3 (named SULT293 cells). The strong dependence of cellular sulfonation on the efflux transport of generated sulfated metabolites revealed an interplay of sulfonation metabolism with efflux transport (or sulfonation-transport interplay). Polymerase chain reaction (PCR) and Western blot analyses demonstrated that SULT293 cells expressed multiple sulfatases such as arylsulfatase A (ARSA), ARSB, and ARSC. Of these three desulfonation enzymes, only ARSB showed significant activities toward hesperetin sulfates. The intrinsic clearance values for the hydrolysis of H3'S and H7S were estimated at 0.6 and 0.5 μl/h/mg, respectively. Furthermore, knockdown of ARSB attenuated the regulatory effect of efflux transporter on cellular sulfonation, whereas overexpression of ABSB enhanced the transporter effect. Taken together, the results indicated that ARSB mediated the sulfonation-transport interplay in SULT293 cells. Copyright © 2016 by The American Society for Pharmacology and Experimental Therapeutics.

21 CFR 177.1200 - Cellophane.

Code of Federal Regulations, 2011 CFR

2011-04-01

.... Castor oil, sulfonated, sodium salt Cellulose acetate butyrate Cellulose acetate propionate Cetyl alcohol... trimethylenediamine (alkyl C16 to C18) Oleic acid, sulfonated, sodium salt Oleyl palmitamide N,N′-Oleoyl...

Condensed Tannin Reacts with SO2 during Wine Aging, Yielding Flavan-3-ol Sulfonates.

PubMed

Ma, Lingjun; Watrelot, Aude A; Addison, Bennett; Waterhouse, Andrew L

2018-06-08

Numerous monomeric and oligomeric flavanol sulfonation products were observed in 10 wines. Levels of 0.85-20.06 and 0-14.72 mg/L were quantified for two monomeric sulfonated flavan-3-ols and, surprisingly, were generally higher than the well-known native flavan-3-ol monomers. Increasing SO 2 levels during wine aging increased the sulfonate-modified flavan-3-ol monomers and dimers along with higher concentrations of native monomers. The results indicate that >10% of SO 2 is reacting with the C-4 carbocation, formed from acid cleavage of the interflavan bond, perhaps by a bimolecular S N 2-type reaction, and as a reducing agent. In addition, the high SO 2 wine had the lowest protein-binding tannin levels, tannin activity, and mean degree of polymerization (mDP), and acidic SO 2 treatment of condensed tannin abolishes protein binding. Thus, SO 2 changes tannin composition during wine aging, and the substantial formation of sulfonate-modified flavan-3-ols may provide an additional explanation for the reduction in astringency of aged red wines.

Electrochemical degradation of perfluoroalkyl and polyfluoroalkyl substances (PFASs) in groundwater.

PubMed

Trautmann, A M; Schell, H; Schmidt, K R; Mangold, K-M; Tiehm, A

2015-01-01

Perfluoroalkyl and polyfluoroalkyl substances (PFASs) represent hazardous pollutants and are frequently detected in the environment, e.g. in contaminated groundwater. PFASs are persistent to biodegradation and conventional oxidation processes such as ozonation. In this study electrochemical degradation of PFASs on boron-doped diamond (BDD) electrodes is demonstrated. Experiments were performed with model solutions and contaminated groundwater with a dissolved organic carbon (DOC) content of 13 mg/L. The perfluorinated carboxylic acids (PFCAs) perfluorobutanoate, perfluoropentanoate, perfluorohexanoate, perfluoroheptanoate and perfluorooctanoate, and the perfluorinated sulfonic acids (PFSAs) perfluorobutane sulfonate, perfluorohexane sulfonate, perfluorooctane sulfonate and 6:2 fluorotelomer sulfonate were detected in the groundwater samples. At PFAS concentrations ranging from 0.26 to 34 mg/L (0.7 to 79 μM), the degradation of PFASs was achieved despite of the high DOC background. Pseudo first-order kinetic constants of PFSA degradation increased with the increase of carbon chain length. Fluoride formation as well as the generation of PFCAs with shortened chain lengths was observed. Inorganic byproducts such as perchlorate were also formed and have to be considered in further process optimization.

Natural and surfactant modified zeolites: A review of their applications for water remediation with a focus on surfactant desorption and toxicity towards microorganisms.

PubMed

Reeve, Peter J; Fallowfield, Howard J

2018-01-01

The objective of this review is to highlight the need for further investigation of microbial toxicity caused by desorption of surfactant from Surfactant Modified Zeolite (SMZ). SMZ is a low cost, versatile permeable reactive media which has the potential to treat multiple classes of contaminants. With this combination of characteristics, SMZ has significant potential to enhance water and wastewater treatment processes. Surfactant desorption has been identified as a potential issue for the ongoing usability of SMZ. Few studies have investigated the toxicity of surfactants used in zeolite modification towards microorganisms and fewer have drawn linkages between surfactant desorption and surfactant toxicity. This review provides an overview of natural zeolite chemistry, characteristics and practical applications. The chemistry of commonly used surfactants is outlined, along with the kinetics that drive their adsorption to the zeolite surface. Methodologies to characterise this surfactant loading are also described. Applications of SMZ in water remediation are highlighted, giving focus to applications which deal with biological pollutants and where microorganisms play a role in the remediation process. Studies that have identified surfactant desorption from SMZ are outlined. Finally, the toxicity of a commonly used cationic surfactant towards microorganisms is discussed. This review highlights the potential for surfactant to desorb from the zeolite surface and the need for further research into the toxicity of this desorbed surfactant towards microorganisms, including pathogens and environmental microbes. Copyright © 2017 Elsevier Ltd. All rights reserved.

SURFACTANT BASED ENHANCED OIL RECOVERY AND FOAM MOBILITY CONTROL

DOE Office of Scientific and Technical Information (OSTI.GOV)

George J. Hirasaki; Clarence A. Miller; Gary A. Pope

2004-07-01

Surfactant flooding has the potential to significantly increase recovery over that of conventional waterflooding. The availability of a large number of surfactants makes it possible to conduct a systematic study of the relation between surfactant structure and its efficacy for oil recovery. Also, the addition of an alkali such as sodium carbonate makes possible in situ generation of surfactant and significant reduction of surfactant adsorption. In addition to reduction of interfacial tension to ultra-low values, surfactants and alkali can be designed to alter wettability to enhance oil recovery. An alkaline surfactant process is designed to enhance spontaneous imbibition in fractured,more » oil-wet, carbonate formations. It is able to recover oil from dolomite core samples from which there was no oil recovery when placed in formation brine. Mobility control is essential for surfactant EOR. Foam is evaluted to improve the sweep efficiency of surfactant injected into fractured reservoirs. UTCHEM is a reservoir simulator specially designed for surfactant EOR. A dual-porosity version is demonstrated as a potential scale-up tool for fractured reservoirs.« less

Copper-Catalyzed Oxidative Reaction of β-Keto Sulfones with Alcohols via C-S Bond Cleavage: Reaction Development and Mechanism Study.

PubMed

Du, Bingnan; Wang, Wenmin; Wang, Yang; Qi, Zhenghang; Tian, Jiaqi; Zhou, Jie; Wang, Xiaochen; Han, Jianlin; Ma, Jing; Pan, Yi

2018-02-16

A Cu-catalyzed cascade oxidative radical process of β-keto sulfones with alcohols has been achieved by using oxygen as an oxidant. In this reaction, β-keto sulfones were converted into sulfinate esters under the oxidative conditions via cleavage of C-S bond. Experimental and computational studies demonstrate that a new pathway is involved in this reaction, which proceeds through the formation of the key four-coordinated Cu II intermediate, O-O bond homolysis induced C-S bond cleavage and Cu-catalyzed esterification to form the final products. This reaction provides a new strategy to sulfonate esters and enriches the research content of C-S bond cleavage and transformations. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis and Process Optimization of Electrospun PEEK-Sulfonated Nanofibers by Response Surface Methodology

PubMed Central

Boaretti, Carlo; Roso, Martina; Lorenzetti, Alessandra; Modesti, Michele

2015-01-01

In this study electrospun nanofibers of partially sulfonated polyether ether ketone have been produced as a preliminary step for a possible development of composite proton exchange membranes for fuel cells. Response surface methodology has been employed for the modelling and optimization of the electrospinning process, using a Box-Behnken design. The investigation, based on a second order polynomial model, has been focused on the analysis of the effect of both process (voltage, tip-to-collector distance, flow rate) and material (sulfonation degree) variables on the mean fiber diameter. The final model has been verified by a series of statistical tests on the residuals and validated by a comparison procedure of samples at different sulfonation degrees, realized according to optimized conditions, for the production of homogeneous thin nanofibers. PMID:28793427

Synthesis and Process Optimization of Electrospun PEEK-Sulfonated Nanofibers by Response Surface Methodology.

PubMed

Boaretti, Carlo; Roso, Martina; Lorenzetti, Alessandra; Modesti, Michele

2015-07-07

In this study electrospun nanofibers of partially sulfonated polyether ether ketone have been produced as a preliminary step for a possible development of composite proton exchange membranes for fuel cells. Response surface methodology has been employed for the modelling and optimization of the electrospinning process, using a Box-Behnken design. The investigation, based on a second order polynomial model, has been focused on the analysis of the effect of both process (voltage, tip-to-collector distance, flow rate) and material (sulfonation degree) variables on the mean fiber diameter. The final model has been verified by a series of statistical tests on the residuals and validated by a comparison procedure of samples at different sulfonation degrees, realized according to optimized conditions, for the production of homogeneous thin nanofibers.

Research progress of surfactant

NASA Astrophysics Data System (ADS)

Zheng, Minyi; Mo, Lingyun; Qin, Ruqiong; Liang, Liying; Zhang, Fan

2017-01-01

With the rapid development of surfactant and the large growing use of the materials, the safety of surfactant may be a problem that draw worldwide attention. The surfactant can be discharged into environment through various approach and may cause toxic effects in organism. This paper reviews the environmental effects of surfactant materials for plants and animals, and raises some questions by describing the results of environmental toxicology. We put it that it is a great significant of promote the sustainable development of surfactant industry through a comprehensive understanding of surfactant environmental safety.

Thermally cleavable surfactants

DOE Office of Scientific and Technical Information (OSTI.GOV)

McElhanon, James R; Simmons, Blake A; Zifer, Thomas

2009-11-24

Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments or the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

Thermally cleavable surfactants

DOE Office of Scientific and Technical Information (OSTI.GOV)

McElhanon, James R; Simmons, Blake A; Zifer, Thomas

2009-09-29

Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments or the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

Thermally cleavable surfactants

DOEpatents

McElhanon, James R [Manteca, CA; Simmons, Blake A [San Francisco, CA; Zifer, Thomas [Manteca, CA; Jamison, Gregory M [Albuquerque, NM; Loy, Douglas A [Albuquerque, NM; Rahimian, Kamyar [Albuquerque, NM; Long, Timothy M [Urbana, IL; Wheeler, David R [Albuquerque, NM; Staiger, Chad L [Albuquerque, NM

2006-04-04

Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments and the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.