The Role of Grain Boundary Chemistry and the Environment on Intergranular Fracture.

DTIC Science & Technology

1980-10-01

and alloys as well. Grain boundary segregation of phosphorus, for example, has been observed in thermally treated nickel-base alloys such as Inconel ...base alloys such as Inconel 600 and Hastelloy C-276. Hence, Ni-P binary glasses may be considered to be good structural and chemical analog of grain...p. 625 17. H.W. Pickering and M. Zamanzedeh: This Conference, Poster Session 18. B.J. Berkowitz, J.J. Burton, C.R. Helms and R.S. Polizzotti

Method for homogenizing alloys susceptible to the formation of carbide stringers and alloys prepared thereby

DOEpatents

Braski, David N.; Leitnaker, James M.

1980-01-01

A novel fabrication procedure prevents or eliminates the reprecipitation of segregated metal carbides such as stringers in Ti-modified Hastelloy N and stainless steels to provide a novel alloy having carbides uniformly dispersed throughout the matrix. The fabrication procedure is applicable to other alloys prone to the formation of carbide stringers. The process comprises first annealing the alloy at a temperature above the single phase temperature for sufficient time to completely dissolve carbides and then annealing the single phase alloy for an additional time to prevent the formation of carbide stringers upon subsequent aging or thermomechanical treatment.

Oxidation of high-temperature alloys (superalloys) at elevated temperatures in air: I

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hussain, N.; Shahid, K.A.; Rahman, S.

1994-04-01

Four commercial alloys - Hastelloy C-4, alloy 1.4306S (SS 304L), Incoloy 800H, and Incoloy 825 - were studied for their oxidation behavior at elevated temperatures. Specimens were exposed to air from 600 to 1200[degree]C for 1 to 400 hr. Reaction kinetics of oxidation were determined, and the morphology of the surface-oxide scales was investigated. Hastelloy C-4 showed better resistance to oxidation for exposure temperatures up to 1000[degree]C in comparison with the other three alloys. In this temperature range, it follows a cubic rate law of oxidation due to formation of uniform, protective, and adherent oxide scales. The latter three alloysmore » obeyed the parabolic rate law at 1000[degree]C and 1200[degree]C, but for lower temperatures a mixed behavior was shown. The oxide layer developed on the alloy 1.4306S was always in the form of stratified nodules/warts. For longer exposures the nodules joined each other to form continuous but discrete layers. Incoloy 800H and Incoloy 825 behaved in an almost identical manner, their reaction kinetics being governed by the parabolic rate law throughout the temperature range. Oxide spalling was observed at all temperatures. In contrast to Incoloy 800H the Incoloy 825 was totally oxidized for longer exposures at 1200[degree]C. 16 refs., 12 figs., 1 tab.« less

Feasibility of EB Welded Hastelloy X and Combination of Refractory Metals

NASA Technical Reports Server (NTRS)

Martinez, Diana A.

2004-01-01

As NASA continues to expand its horizon, exploration and discovery creates the need of advancement in technology. The Jupiter Icy Moon Orbiter's (JIMO) mission to explore and document the outer surfaces, rate the possibility of holding potential life forms, etc. within the three moons (Callisto, Ganymede, and Europa) proves to be challenging. The orbiter itself consists of many sections including: the nuclear reactor and the power conversion system, the radiator panels, and the thrusters and antenna. The nuclear reactor serves as a power source, and if successfully developed, can operate for extended periods. During the duration of my tenure at NASA Glenn Research Center's (NASA GRC) Advanced Metallics Branch, I was assigned to assist Frank J. Ritzert on analyzing the feasibility of the Electron Beam Welded Hastelloy X (HX), a nickel-based superalloy, to Niobium- 1 %Zirconium (Nb-1 Zr) and other refractory metals/alloys including Tantalum, Molybdenum, Tungsten, and Rhenium alloys. This welding technique is going to be used for the nuclear reactor within JIMO.

Electrospark Deposition for Depot- and Field-Level Component Repair and Replacement of Hard Chromium Plating

DTIC Science & Technology

2008-02-01

with an ASAP proprietary process. Corrosion applications frequently are addressed with iron- aluminide and nickel alloys such as Inconel 625 alloy...IN625) and Hastelloy C-22. Wear applications commonly treated with ESD include cutting edges of chipper knives, saw teeth, and mower blades ; wear...Applications for ESD repair include components of steel, stainless steel, nickel- and cobalt-based superalloys, aluminum, Monel, titanium , and magnesium

Embrittlement of nickel-, cobalt-, and iron-base superalloys by exposure to hydrogen

NASA Technical Reports Server (NTRS)

Gray, H. R.

1975-01-01

Five nickel-base alloys (Inconel 718, Udimet 700, Rene 41, Hastelloy X, and TD-NiCr), one cobalt-base alloy (L-605), and an iron-base alloy (A-286) were exposed in hydrogen at 0.1 MN/sq m (15 psi) at several temperatures in the range from 430 to 980 C for as long as 1000 hours. These alloys were embrittled to varying degrees by such exposures in hydrogen. Embrittlement was found to be: (1) sensitive to strain rate, (2) reversible, (3) caused by large concentrations of absorbed hydrogen, and (4) not associated with any detectable microstructural changes in the alloys. These observations are consistent with a mechanism of internal reversible hydrogen embrittlement.

Laser texturing of Hastelloy C276 alloy surface for improved hydrophobicity and friction coefficient

NASA Astrophysics Data System (ADS)

Yilbas, B. S.; Ali, H.

2016-03-01

Laser treatment of Hastelloy C276 alloy is carried out under the high pressure nitrogen assisting gas environment. Morphological and metallurgical changes in the laser treated layer are examined using the analytical tools including, scanning electron and atomic force microscopes, X-ray diffraction, energy dispersive spectroscopy, and Fourier transform infrared spectroscopy. Microhardness is measured and the residual stress formed in the laser treated surface is determined from the X-ray data. The hydrophibicity of the laser treated surface is assessed using the sessile drop method. Friction coefficient of the laser treated layer is obtained incorporating the micro-tribometer. It is found that closely spaced laser canning tracks create a self-annealing effect in the laser treated layer and lowers the thermal stress levels through modifying the cooling rates at the surface. A dense structure, consisting of fine size grains, enhances the microhardness of the surface. The residual stress formed at the surface is compressive and it is in the order of -800 MPa. Laser treatment improves the surface hydrophobicity significantly because of the formation of surface texture composing of micro/nano-pillars.

High-temperature corrosion of UNS N10003 in molten Li 2BeF 4 (FLiBe) salt

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zheng, Guiqiu; Kelleher, Brian; He, Lingfeng

2015-07-30

Here, corrosion testing of Hastelloy N in molten fluoride salt was performed in purified molten 2 7LiF-BeF 2 (66-34mol%) (FLiBe) salt at 700°C for 1000 hours, in pure nickel and graphite capsules. In the nickel capsule tests, the near-surface region of the alloy exhibited an about 200 nm porous structure, an approximately 3.5 μm chromium depleted region, and MoSi 2 precipitates. In tests performed in graphite capsules, the alloy samples gained weight due to the formation of a variety of Cr 3C 2, Cr 7C 3, Mo 2C and Cr 23C 6, carbide phases on the surface and in themore » subsurface regions of the alloy. A Cr depleted region was observed in the near-surface region where Mo thermally diffused toward either surface or grain boundary, which induced approximately 1.4 μm Ni 3Fe alloy layer in this region. The carbide containing layer extended to about 7 μm underneath the Ni 3Fe layer. The presence of graphite dramatically changes the mechanisms of corrosion attack in Hastelloy N in molten FLiBe salt. Evaluated by in terms of the depth of attack, graphite clearly accelerates corrosion, but the results appear to indicate that the formation of Cr 23C 6 phase might stabilize the Cr and mitigate its dissolution in molten FLiBe salt.« less

ECLSS Sustaining Metal Materials Compatibility Final Report, Electrochemical and Crevice Corrosion Test Results

NASA Technical Reports Server (NTRS)

Lee, R. E.

2015-01-01

Electrochemical test results are presented for six noble metals evaluated in two acidic test solutions which are representative of waste liquids processed in the Environmental Control and Life Support System (ECLSS) aboard the International Space Station (ISS). The two test solutions consisted of fresh waste liquid which had been modified with a proposed or alternate pretreatment formulation and its associated brine concentrate. The six test metals included three titanium grades, (Commercially Pure, 6Al-4V alloy and 6Al-4V Low Interstitial alloy), two nickel-chromium alloys (Inconel® 625 and Hastelloy® C276), and one high tier stainless steel (Cronidur® 30).

The effect of hot salt on the mechanical properties of several superalloys

NASA Technical Reports Server (NTRS)

Nelson, E. E.

1972-01-01

The effect of sodium chloride on unstressed, transverse, tensile, metal specimens at elevated temperatures was determined. Results indicate that the mechanical properties of Inconel 718, Rene 41, titanium base alloy 13V-11Cr-3Al, Hastelloy X, HS25 (L605), HS188, and TDNiCr suffer degradation in tensile strength and ductility due to hot salt exposure.

High-temperature low-cycle-fatigue and crack-growth behaviors of three superalloys: HASTELLOY X, HAYNES 230, and HAYNES 188

NASA Astrophysics Data System (ADS)

Lu, Yulin

Low cycle fatigue (LCF) and fatigue crack growth (FCG) experiments on three superalloys HASTELLOY X, HAYNES 230, and HAYNES 188 have been conducted at temperatures from 649 to 982°C. Hold times were imposed at the maximum strain or load to investigate the hold-time effect. In general, the fatigue life decreased as the temperature or hold time increased. However, for the HAYNES 230 alloy at total strain ranges higher than 1.0% and without a hold time, the LCF life was longer at 927°C than at 816°C. This "abnormal" behavior was found to result from the smaller plastic strain amplitude at half-life at 927°C than that at 816°C. An increase in the temperature and/or the introduction of a hold time decreased the hardening rate and increased the softening rate for all the three alloys. The introduction of a hold time and/or the increase of the test temperature progressively changed the fracture mode from the transgranular to mixed trans/inter-granular, then to intergranular feature. Within the two phases of the fatigue process, crack initiation was more severely influenced by the change of the hold time and/or temperature. The FCG data of HASTELLOY X and HAYNES 230 alloys were analyzed with an emphasis on hold-time and temperature effects. The crack grew faster at a higher temperature and a longer hold time. Fracture-mechanics parameters, C*, Ct, and (Ct)avg, were applied to correlate the crack-growth rates. The fatigue-cracking path was mainly transgranular at 816 and 927°C. The cracking path became dominantly intergranular if the hold time increased to 2 min, indicating that the time-dependent damage mechanisms were in control. The Ct and (Ct)avg parameters were capable of consolidating time dependent crack growth rate from different temperatures and alloys. The tests were conducted in air. Therefore, the fracture surfaces were frequently covered with a dark layer of oxides, making fracture feature difficult to identify under scanning-electron-microscopy. To overcome this problem, an oxide-stripping technique has been developed. The sample is first boiled in a potassium permanganate solution for 1 h, and then electrolytically cleaned in an alkaline solution for 5 min.

Corrosion Behavior of Alloys in Molten Fluoride Salts

NASA Astrophysics Data System (ADS)

Zheng, Guiqiu

The molten fluoride salt-cooled high-temperature nuclear reactor (FHR) has been proposed as a candidate Generation IV nuclear reactor. This reactor combines the latest nuclear technology with the use of molten fluoride salt as coolant to significantly enhance safety and efficiency. However, an important challenge in FHR development is the corrosion of structural materials in high-temperature molten fluoride salt. The structural alloys' degradation, particularly in terms of chromium depletion, and the molten salt chemistry are key factors that impact the lifetime of nuclear reactors and the development of future FHR designs. In support of materials development for the FHR, the nickel base alloy of Hastelloy N and iron-chromium base alloy 316 stainless steel are being actively considered as critical structural alloys. Enriched 27LiF-BeF2 (named as FLiBe) is a promising coolant for the FHR because of its neutronic properties and heat transfer characteristics while operating at atmospheric pressure. In this study, the corrosion behavior of Ni-5Cr and Ni-20Cr binary model alloys, and Hastelloy N and 316 stainless steel in molten FLiBe with and without graphite were investigated through various microstructural analyses. Based on the understanding of the corrosion behavior and data of above four alloys in molten FLiBe, a long-term corrosion prediction model has been developed that is applicable specifically for these four materials in FLiBe at 700ºC. The model uses Cr concentration profile C(x, t) as a function of corrosion distance in the materials and duration fundamentally derived from the Fick's diffusion laws. This model was validated with reasonable accuracy for the four alloys by fitting the calculated profiles with experimental data and can be applied to evaluate corrosion attack depth over the long-term. The critical constant of the overall diffusion coefficient (Deff) in this model can be quickly calculated from the experimental measurement of alloys' weight loss due to Cr depletion. While many factors affect the Deff such as the grain boundary type, grain size, precipitates, initial Cr concentration as well as temperature, this model provides a methodology for estimating corrosion attack depth of alloys in molten fluoride salts obviating the need for difficult and challenging experiment.

Materials corrosion in molten lithium fluoride-sodium fluoride-potassium fluoride eutectic salt

NASA Astrophysics Data System (ADS)

Olson, Luke Christopher

Static corrosion studies were undertaken to determine the compatibility of several candidate high temperature materials for a heat transfer loop in a molten alkali fluoride eutectic salt, LiF-NaF-KF: 46.5-11.5-42 mol % (commonly referred to as FLiNaK), as well as a molten chloride near eutectic salt, KCl-MgCl2: 68-32 mol %. Several high temperature alloys: Hastelloy-N, Hastelloy-X, Haynes-230, Inconel-617, and Incoloy-800H, Nb-1Zr, a nearly pure Ni alloy Ni-201, and a C/SiSiC ceramic were exposed to molten FLiNaK at 850°C for 500 h in sealed graphite crucibles under an argon cover gas. Corrosion occurred predominantly from dealloying of Cr from the Cr bearing alloys, an effect that was particularly pronounced at the grain boundaries. Corrosion was noted to occur from selective attack of the Si phase in the C/SiSiC ceramic. Alloy weight-loss/area due to molten fluoride salt exposure correlated with the initial Cr-content of the alloys, and was consistent with the Cr-content measured in the salts after corrosion tests. The alloys' weight-loss/area was also found to correlate to the concentration of carbon present in the nominally 20% Cr containing alloys, due to the formation of chromium carbide phases at the grain boundaries. The corrosion mechanisms for the chloride based salt were found to be similar to those observed in FLiNaK, but the chemical attack was found to be less aggressive. Sulfamate Ni electroplating and Mo plasma spraying of Fe-Ni-Cr alloy coupons was investigated to mitigate Cr dissolution. A chemical vapor deposited pyrolytic carbon and SiC coating was also investigated to protect the C/SiSiC composites. Results indicate that Ni-plating has the potential to provide protection against alloy corrosion in molten fluoride salts. Furthermore, the presence of a chromium-oxide interlayer at the interface of the Ni-plating and alloy substrate can further improve the efficacy of the Ni-plating. The pyrolytic carbon and SiC coating on the C/SiSiC composites was effective in eliminating the attack of the Si phase in the composites. Delamination of the Mo coating in FLiNaK prevented further investigation of this promising approach.

Midwest Structural Sciences Center 2009 Annual Report

DTIC Science & Technology

2010-08-01

simulations. Numerical simulations were carried with a single edge notch beam using an ABAQUS user-element subroutine in conjunction with bilinear and...this effort Digital Image Correlation (DIC) has been applied to measure the coefficient of thermal expansion of the nickel-based super alloy...between 30 and 650°C, the thermal expansion coefficient of Hastelloy X was measured over this entire range and found to be in good agreement with

Preliminary Investigations of Joining Technologies for Attaching Refractory Metals to Ni-Based Superalloys

NASA Technical Reports Server (NTRS)

Gould, Jerry E.; Ritzert, Frank J.; Loewenthal, William S.

2006-01-01

In this study, a range of joining technologies has been investigated for creating attachments between refractory metal and Ni-based superalloys. Refractory materials of interest include Mo-47%Re, T-111, and Ta-10%W. The Ni-based superalloys include Hastelloy X and MarM 247. During joining with conventional processes, these materials have potential for a range of solidification and intermetallic formation-related defects. For this study, three non-conventional joining technologies were evaluated. These included inertia welding, electro-spark deposition (ESD) welding, and magnetic pulse welding (MPW). The developed inertia welding practice closely paralleled that typically used for the refractory metals alloys. Metallographic investigations showed that forging during inertia welding occurred predominantly on the nickel base alloy side. It was also noted that at least some degree of forging on the refractory metal side of the joint was necessary to achieve consistent bonding. Both refractory metals were readily weldable to the Hastelloy X material. When bonding to the MarM 247, results were inconsistent. This was related to the higher forging temperatures of the MarM 247, and subsequent reduced deformation on that material during welding. ESD trials using a Hastelloy X filler were successful for all material combinations. ESD places down very thin (5- to 10- m) layers per pass, and interactions between the substrates and the fill were limited (at most) to that layer. For the refractory metals, the fill only appeared to wet the surface, with minimal dilution effects. Microstructures of the deposits showed high weld metal integrity with maximum porosity on the order of a few percent. Some limited success was also obtained with MPW. In these trials, only the T-111 tubes were used. Joints were possible for the T-111 tube to the Hastelloy X bar stock, but the stiffness of the tube (resisting collapse) necessitated the use of very high power levels. These power levels resulted in damage to the equipment (concentrator) during welding. It is of note that the joint made showed the typical wavy bond microstructure associated with magnetic pulse/explosion bond joints. Joints were not possible between the T-111 tube and the MarM 247 bar stock. In this case, the MarM 247 shattered before sufficient impact forces could be developed for bonding.

Modeling and experimental study of oil/water contact angle on biomimetic micro-parallel-patterned self-cleaning surfaces of selected alloys used in water industry

NASA Astrophysics Data System (ADS)

Nickelsen, Simin; Moghadam, Afsaneh Dorri; Ferguson, J. B.; Rohatgi, Pradeep

2015-10-01

In the present study, the wetting behavior of surfaces of various common metallic materials used in the water industry including C84400 brass, commercially pure aluminum (99.0% pure), Nickle-Molybdenum alloy (Hastelloy C22), and 316 Stainless Steel prepared by mechanical abrasion and contact angles of several materials after mechanical abrasion were measured. A model to estimate roughness factor, Rf, and fraction of solid/oil interface, ƒso, for surfaces prepared by mechanical abrasion is proposed based on the assumption that abrasive particles acting on a metallic surface would result in scratches parallel to each other and each scratch would have a semi-round cross-section. The model geometrically describes the relation between sandpaper particle size and water/oil contact angle predicted by both the Wenzel and Cassie-Baxter contact type, which can then be used for comparison with experimental data to find which regime is active. Results show that brass and Hastelloy followed Cassie-Baxter behavior, aluminum followed Wenzel behavior and stainless steel exhibited a transition from Wenzel to Cassie-Baxter. Microstructural studies have also been done to rule out effects beyond the Wenzel and Cassie-Baxter theories such as size of structural details.

Material Data Representation of Hysteresis Loops for Hastelloy X Using Artificial Neural Networks

NASA Technical Reports Server (NTRS)

Alam, Javed; Berke, Laszlo; Murthy, Pappu L. N.

1993-01-01

The artificial neural network (ANN) model proposed by Rumelhart, Hinton, and Williams is applied to develop a functional approximation of material data in the form of hysteresis loops from a nickel-base superalloy, Hastelloy X. Several different ANN configurations are used to model hysteresis loops at different cycles for this alloy. The ANN models were successful in reproducing the hysteresis loops used for its training. However, because of sharp bends at the two ends of hysteresis loops, a drift occurs at the corners of the loops where loading changes to unloading and vice versa (the sharp bends occurred when the stress-strain curves were reproduced by adding stress increments to the preceding values of the stresses). Therefore, it is possible only to reproduce half of the loading path. The generalization capability of the network was tested by using additional data for two other hysteresis loops at different cycles. The results were in good agreement. Also, the use of ANN led to a data compression ratio of approximately 22:1.

Exploratory screening tests of several alloys and coatings for automobile thermal reactors

NASA Technical Reports Server (NTRS)

Oldrieve, R. E.

1971-01-01

A total of 23 materials (including uncoated ferritic and austenitic iron-base alloys, uncoated nickel and cobalt-base superalloys, and several different coatings on AISI 304 stainless steel) were screened as test coupons on a rack in an automobile thermal reactor. Test exposures were generally 51 hours including 142 thermal cycles of 10 minutes at 1010 + or - 30 C test coupon temperature and 7-minutes cool-down to about 510 C. Materials that exhibited corrosion resistance better than that of Hastelloy X include: a ferritic iron alloy with 6 weight percent aluminum; three nickel-base superalloys; two diffused-aluminum coatings on AISI 304; and a Ni-Cr slurry-sprayed coating on AISI 304. Preliminary comparison is made on the performance of the directly impinged coupons and a reactor core of the same material.

Thermomechanical deformation testing and modeling in the presence of metallurgical instabilities. M.S. Thesis - Akron Univ. Final Report

NASA Technical Reports Server (NTRS)

Castelli, Michael G.

1990-01-01

A number of viscoplastic constitutive models were developed to describe deformation behavior under complex combinations of thermal and mechanical loading. Questions remain, however, regarding the validity of procedures used to characterize these models for specific structural alloys. One area of concern is that the majority of experimental data available for this purpose are determined under isothermal conditions. This experimental study is aimed at determining whether viscoplastic constitutive theories characterized using an isothermal data base can adequately model material response under the complex thermomechanical loading conditions typical of power generation service. The approach adopted was to conduct a series of carefully controlled thermomechanical experiments on a nickel-based superalloy, Hastelloy Alloy X. Previous investigations had shown that this material experiences metallurgical instabilities leading to complex hardening behavior, termed dynamic strain aging. Investigating this phenomenon under full thermomechanical conditions leads to a number of challenging experimental difficulties which up to the present work were unresolved. To correct this situation, a number of advances were made in thermomechanical testing techniques. Advanced methods for dynamic temperature gradient control, phasing control and thermal strain compensation were developed and incorporated into real time test control software. These advances allowed the thermomechanical data to be analyzed with minimal experimental uncertainty. The thermomechanical results were evaluated on both a phenomenological and microstructural basis. Phenomenological results revealed that the thermomechanical hardening trends were not bounded by those displayed under isothermal conditions. For the case of Hastelloy Alloy X (and similar dynamic strain aging materials), this strongly suggests that some form of thermomechanical testing is necessary when characterizing a thermoviscoplastic deformation model. Transmission electron microscopy was used to study the microstructural physics, and analyze the unique phenomenological behavior.

Advanced Catalytic Combustors for Low Pollutant Emissions

DTIC Science & Technology

1979-11-01

liner materials in both designs are sheet or forged HS188 . This alloy was designed for stability of the microstructure and properties during heat...625 Inco 718 I: Inca 625 HS188 L605 Hast X Figure 37. Catalytic Combustor Materials. 111 &I ~ 4 L. ,.Add. R service. The hot corrosion resistance of... HS188 is similar to L605 and somewhat F better than Hastelloy X, another common liner material. HS188 exhibits good low cyclo fatigue resistance up to

Catalytic effect of different reactor materials under subcritical water conditions: decarboxylation of cysteic acid into taurine

NASA Astrophysics Data System (ADS)

Faisal, M.

2018-03-01

In order to understand the influence of reactor materials on the catalytic effect for a particular reaction, the decomposition of cysteic acid from Ni/Fe-based alloy reactors under subcritical water conditions was examined. Experiments were carried out in three batch reactors made of Inconel 625, Hastelloy C-22 and SUS 316 over temperatures of 200 to 300 °C. The highest amount of eluted metals was found for SUS 316. The results demonstrated that reactor materials contribute to the resulting product. Under the tested conditions, cysteic acid decomposes readily with SUS 316. However, the Ni-based materials (Inconel 625 and Hastelloy C-22) show better resistance to metal elution. It was found that among the materials used in this work, SUS 316 gave the highest reaction rate constant of 0.1934 s‑1. The same results were obtained at temperatures of 260 and 300 °C. Investigation of the Arrhenius activation energy revealed that the highest activation energy was for Hastelloy C-22 (109 kJ/mol), followed by Inconel 625 (90 kJ/mol) and SUS 316 (70 kJ/mol). The decomposition rate of cysteic acid was found to follow the results for the trend of the eluted metals. Therefore, it can be concluded that the decomposition of cysteic acid was catalyzed by the elution of heavy metals from the surface of the reactor. The highest amount of taurine from the decarboxylation of cysteic acid was obtained from SUS 316.

Characterization of complex carbide–silicide precipitates in a Ni–Cr–Mo–Fe–Si alloy modified by welding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhattacharyya, D., E-mail: dhb@ansto.gov.au; Davis, J.; Drew, M.

2015-07-15

Nickel based alloys of the type Hastelloy-N™ are ideal candidate materials for molten salt reactors, as well as for applications such as pressure vessels, due to their excellent resistance to creep, oxidation and corrosion. In this work, the authors have attempted to understand the effects of welding on the morphology, chemistry and crystal structure of the precipitates in the heat affected zone (HAZ) and the weld zone of a Ni–Cr–Mo–Fe–Si alloy similar to Hastelloy-N™ in composition, by using characterization techniques such as scanning and transmission electron microscopy. Two plates of a Ni–Cr–Mo–Fe–Si alloy GH-3535 were welded together using a TiGmore » welding process without filler material to achieve a joint with a curved molten zone with dendritic structure. It is evident that the primary precipitates have melted in the HAZ and re-solidified in a eutectic-like morphology, with a chemistry and crystal structure only slightly different from the pre-existing precipitates, while the surrounding matrix grains remained unmelted, except for the zones immediately adjacent to the precipitates. In the molten zone, the primary precipitates were fully melted and dissolved in the matrix, and there was enrichment of Mo and Si in the dendrite boundaries after solidification, and re-precipitation of the complex carbides/silicides at some grain boundaries and triple points. The nature of the precipitates in the molten zone varied according to the local chemical composition. - Graphical abstract: Display Omitted - Highlights: • Ni-based alloy with Cr, Mo, Si, Fe and C was welded, examined with SEM, EBSD, and TEM. • Original Ni{sub 2}(Mo,Cr){sub 4}(Si,C) carbides changed from equiaxed to lamellar shape in HAZ. • Composition and crystal structure remained almost unchanged in HAZ. • Original carbides changed to lamellar Ni{sub 3}(Mo,Cr){sub 3}(Si,C) in some cases in weld metal. • Precipitates were mostly incoherent, but semi-coherent in some cases in weld metal.« less

MATE (Materials for Advanced Turbine Engines) Program, Project 3. Volume 2: Design, fabrication and evaluation of an oxide dispersion strengthened sheet alloy combustor liner

NASA Technical Reports Server (NTRS)

Bose, S.; Sheffler, K. D.

1988-01-01

The suitability of wrought oxide dispersion strengthened (ODS) superalloy sheet for gas turbine engine combustor applications was evaluated. Two yttria (Y2O3) dispersion strengthened alloys were evaluated; Incoloy MA956 and Haynes Development Alloy (HDA) 8077 (NiCrAl base). Preliminary tests showed both alloys to be potentially viable combustor materials, with neither alloy exhibiting a significant advantage over the other. MA956 was selected as the final alloy based on manufacturing reproducibility for evaluation as a burner liner. A hybrid PW2037 inner burner liner containing MA956 and Hastelloy X components and using a louvered configuration was designed and constructed. The louvered configuration was chosen because of field experience and compatibility with the bill of material PW2037 design. The simulated flight cycle for the ground based engine tests consisted of 4.5 min idle, 1.5 min takeoff and intermediate conditions in a PW2037 engine with average uncorrected combustor exit temperature of 1527 C. Post test evaluation consisting of visual observations and fluorescent penetrant inspections was conducted after 500 cycles of testing. No loss of integrity in the burner liner was shown.

Nondestructive evaluation of loading and fatigue effects in Haynes(R) 230(R) alloy

NASA Astrophysics Data System (ADS)

Saleh, Tarik Adel

Nondestructive evaluation is a useful method for studying the effects of deformation and fatigue. In this dissertation I employed neutron and X-ray diffraction, nonlinear resonant ultrasound spectroscopy (NRUS), and infrared thermography to study the effects of deformation and fatigue on two different nickel based superalloys. The alloys studied were HAYNES 230, a solid solution strengthened alloy with 4% M6C carbides, and secondarily HASTELLOY C-2000 a similar single phase alloy. Using neutron and X-ray diffraction, the deformation behavior of HAYNES 230 was revealed to be composite-like during compression, but unusual in tension, where the carbides provide strengthening until just after the macroscopic yield strength and then they begin to debond and crack, creating a tension-compression asymmetry that is revealed clearly by in situ diffraction. In fatigue of HAYNES 230, the hkl elastic strains changed very little in tension-tension fatigue. However, in situ tension-compression studies showed large changes over the initial stages of fatigue. The HAYNES 230 samples studies had two distinct starting textures, measured by neutron diffraction. Some samples were texture free initially and deformed in tension and compression to fiber textures. Other samples started with a bimodal texture due to cross-rolling and incomplete annealing. The final texture of these bimodal samples is shown through modeling to be a superposition of the initial texture and typical FCC deformation mechanisms. The texture-free samples deformed significantly more macroscopically and in internal elastic strains than the samples with the cross-rolled texture. In contrast to the relative insensitivity of neutron diffraction to the effects of tension-tension fatigue, NRUS revealed large differences between as-received and progressively fatigued samples. This showed that microcracking and void formation are the primary mechanisms responsible for fatigue damage in tension-tension fatigue. NRUS is shown to be a useful complimentary technique to neutron diffraction to evaluate fatigue damage. Finally, infrared thermography is used to show temperature changes over the course of fatigue in HASTELLOY C-2000. Four stages of temperature are shown over the course of a single fatigue test. Both empirical and theoretical relationships between steady state temperature and fatigue life are developed and presented.

Study of the effects of gaseous environmental on the hot corrosion of superalloy materials

NASA Technical Reports Server (NTRS)

Smeggil, J. G.

1981-01-01

Studies have been conducted to examine the effect of low concentrations of NaCl(g) on the high temperature oxidation behavior of complex superalloys and potential coating formulations modified by silicon and reactive element (i.e., yttrium and hafnium) additions. Depending on alloy composition, a variety of effects were thermogravimetrically produced. Aluminum free alloys such as MAR-M509 and Hastelloy X with molybdenum and tungsten in solid solution showed accelerated (or breakaway) kinetics similar to that observed for Ni-Cr alloys. For IN-792, an alloy high in chromium and low in aluminum, molybdenum and tungsten present in solid solution does not adversely affect oxidation kinetics in the presence of NaCl(g). On the other hand, nickel-base alloys high in aluminum and molybdenum are catastrophically attacked by NaCl-bearing atmospheres. Silicon additions were, in general, observed to slightly improve the oxidation resistance of Ni, Ni-40Cr and CoCrAlY compositions in NaCl(g)-bearing atmospheres. To the degree that processes responsible for Al2O3 whisker formation deleteriously affect protective scale adherence, the addition of yttrium or hafnium can inhibit such whisker growth.

Development of porcelain enamel passive thermal control coatings

NASA Technical Reports Server (NTRS)

Levin, H.; Lent, W. E.; Buettner, D. H.

1973-01-01

A white porcelain enamel coating was developed for application to high temperature metallic alloy substrates on spacecraft. The coating consists of an optically opacifying zirconia pigment, a lithia-zirconia-silica frit, and an inorganic pigment dispersant. The coating is fired at 1000 to 1150 C to form the enamel. The coating has a solar absorptance of 0.22 and a total normal emittance of 0.82 for a 0.017 cm thick coating. The coating exhibits excellent adhesion, cleanability, and integrity and is thermal shock resistant to 900 C. Capability to coat large panels has been demonstrated by successful coating of 30 cm x 30 cm Hastelloy X alloy panels. Preliminary development of low temperature enamels for application to aluminum and titanium alloy substrates was initiated. It was determined that both leaded and leadless frits were feasible when applied with appropriate mill fluxes. Indications were that opacification could be achieved at firing temperatures below 540 C for extended periods of time.

Effect of Molybdenum on the Corrosion Behavior of High-Entropy Alloys CoCrFeNi 2 and CoCrFeNi 2 Mo 0.25 under Sodium Chloride Aqueous Conditions

DOE PAGES

Rodriguez, Alvaro A.; Tylczak, Joseph H.; Gao, Michael C.; ...

2018-01-01

The corrosion behavior of high-entropy alloys (HEAs) CoCrFeNi 2 and CoCrFeNi 2 Mo 0.25 was investigated in 3.5 wt. percent sodium chloride (NaCl) at 25°C by electrochemical methods. Their corrosion parameters were compared to those of HASTELLOY® C-276 (UNS N10276) and stainless steel 316L (UNS 31600) to assess the suitability of HEAs for potential industrial applications in NaCl simulating seawater type environments. The corrosion rates were calculated using corrosion current determined from electrochemical experiments for each of the alloys. In addition, potentiodynamic polarization measurements can indicate active, passive, and transpassive behavior of the metal as well as potential susceptibility to pittingmore » corrosion. Cyclic voltammetry (CV) can confirm the alloy susceptibility to pitting corrosion. Electrochemical impedance spectroscopy (EIS) elucidates the corrosion mechanism under studied conditions. The results of the electrochemical experiments and scanning electron microscopy (SEM) analyses of the corroded surfaces revealed general corrosion on alloy CoCrFeNi 2 Mo 0.25 and HASTELLOY C-276 and pitting corrosion on alloy CoCrFeNi 2 and stainless steel 316L.« less

Effect of Molybdenum on the Corrosion Behavior of High-Entropy Alloys CoCrFeNi 2 and CoCrFeNi 2 Mo 0.25 under Sodium Chloride Aqueous Conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodriguez, Alvaro A.; Tylczak, Joseph H.; Gao, Michael C.

The corrosion behavior of high-entropy alloys (HEAs) CoCrFeNi 2 and CoCrFeNi 2 Mo 0.25 was investigated in 3.5 wt. percent sodium chloride (NaCl) at 25°C by electrochemical methods. Their corrosion parameters were compared to those of HASTELLOY® C-276 (UNS N10276) and stainless steel 316L (UNS 31600) to assess the suitability of HEAs for potential industrial applications in NaCl simulating seawater type environments. The corrosion rates were calculated using corrosion current determined from electrochemical experiments for each of the alloys. In addition, potentiodynamic polarization measurements can indicate active, passive, and transpassive behavior of the metal as well as potential susceptibility to pittingmore » corrosion. Cyclic voltammetry (CV) can confirm the alloy susceptibility to pitting corrosion. Electrochemical impedance spectroscopy (EIS) elucidates the corrosion mechanism under studied conditions. The results of the electrochemical experiments and scanning electron microscopy (SEM) analyses of the corroded surfaces revealed general corrosion on alloy CoCrFeNi 2 Mo 0.25 and HASTELLOY C-276 and pitting corrosion on alloy CoCrFeNi 2 and stainless steel 316L.« less

Study of the Microstructure and Cracking Mechanisms of Hastelloy X Produced by Laser Powder Bed Fusion.

PubMed

Marchese, Giulio; Basile, Gloria; Bassini, Emilio; Aversa, Alberta; Lombardi, Mariangela; Ugues, Daniele; Fino, Paolo; Biamino, Sara

2018-01-11

Hastelloy X (HX) is a Ni-based superalloy which suffers from high crack susceptibility during the laser powder bed fusion (LPBF) process. In this work, the microstructure of as-built HX samples was rigorously investigated to understand the main mechanisms leading to crack formation. The microstructural features of as-built HX samples consisted of very fine dendrite architectures with dimensions typically less than 1 µm, coupled with the formation of sub-micrometric carbides, the largest ones were mainly distributed along the interdendritic regions and grain boundaries. From the microstructural analyses, it appeared that the formation of intergranular carbides provided weaker zones, which combined with high thermal residual stresses resulted in hot cracks formation along the grain boundaries. The carbides were extracted from the austenitic matrix and characterized by combining different techniques, showing the formation of various types of Mo-rich carbides, classified as M₆C, M 12 C and M n C m type. The first two types of carbides are typically found in HX alloy, whereas the last one is a metastable carbide probably generated by the very high cooling rates of the process.

Effects of NaOH Concentration on CO2 Reduction via Hydrothermal Water

NASA Astrophysics Data System (ADS)

Onoki, Takamasa; Takahashi, Hiro; Kori, Toshinari; Yamasaki, Nakamichi; Hashida, Toshiyuki

2006-05-01

The reductions of CO2 under hydrothermal conditions were investigated by using the micro autoclave (45cm3) lined with Hastelloy-C alloy. Sodium hydrogen carbonate (NaHCO3) was used as a starting material. H2 gas was used as reducing agents. NaHCO3 powder, H2 gas and water put into the autoclave simultaneously. The autoclave was heated upto 300°C by induction heater. In this study, effects of pH value of the NaOH solution in the autoclave are investigated. Reaction products were analyzed with gas chromatographs (GC), liquid chromatographs (LC), X-ray diffractometor (XRD) and Scanning electron microscopy (SEM). The following things were showed in this research: CO2 was reducted to HCOO- and CH4 at high conversion ratio under hydrothermal conditions. HCOO- was formed at high selectivity using Hastelloy-C reactor in the alkaline solution with Raney Ni catalyst. Raney Ni was exellent methanation catalyst, and CH4 formation progressed via HCO3-, not via CO. It is cleared that the NaOH solution in the autoclave should be kept pH value 11.0 for the highest conversion ratio from CO2 to useful carbonic compounds (CH4, HCOO-).

Study of the Microstructure and Cracking Mechanisms of Hastelloy X Produced by Laser Powder Bed Fusion

PubMed Central

Basile, Gloria; Bassini, Emilio; Ugues, Daniele; Fino, Paolo

2018-01-01

Hastelloy X (HX) is a Ni-based superalloy which suffers from high crack susceptibility during the laser powder bed fusion (LPBF) process. In this work, the microstructure of as-built HX samples was rigorously investigated to understand the main mechanisms leading to crack formation. The microstructural features of as-built HX samples consisted of very fine dendrite architectures with dimensions typically less than 1 µm, coupled with the formation of sub-micrometric carbides, the largest ones were mainly distributed along the interdendritic regions and grain boundaries. From the microstructural analyses, it appeared that the formation of intergranular carbides provided weaker zones, which combined with high thermal residual stresses resulted in hot cracks formation along the grain boundaries. The carbides were extracted from the austenitic matrix and characterized by combining different techniques, showing the formation of various types of Mo-rich carbides, classified as M6C, M12C and MnCm type. The first two types of carbides are typically found in HX alloy, whereas the last one is a metastable carbide probably generated by the very high cooling rates of the process. PMID:29324658

Investigation of the hydrochlorination of SiCl4

NASA Technical Reports Server (NTRS)

Mui, J. Y. P.

1982-01-01

A research and development program on the hydrochlorination of silicon tetrachloride and metallurgical grade (m.g.) silicon metal to trichlorosilane was carried out as scheduled. Effects of pressure and temperature on this reaction are reported. The presence of HCl in the reaction product mixture was successfully analyzed. Approximately 0.1% to 0.5% HCl based on total chlorosilanes were produced by the hydrochlorination reaction. Experiments on the corrosion study were carried out to evaluate a variety of metals and alloys as the material of construction for the hydrochlorination reactor. Material includes carbon steel, nickel, copper, Alloy 400 (Monel), stainless steel (Type 304), Incoloy 800H and Hastelloy B-2. The corrosion test was carried out at reaction temperature of 500 C, pressure of 300 psig and H2/SiCl4 feed ratio of 2.0 for a total of 87 hours. Results of the corrosion test show that all the test samples achieved a weigh gain.

Stress Corrosion Evaluation of Nitinol 60 for the International Space Station Water Recycling System

NASA Technical Reports Server (NTRS)

Torres, P. D.

2016-01-01

A stress corrosion cracking (SCC) evaluation of Nitinol 60 was performed because this alloy is considered a candidate bearing material for the Environmental Control and Life Support System (ECLSS), specifically in the Urine Processing Assembly of the International Space Station. An SCC evaluation that preceded this one during the 2013-2014 timeframe included various alloys: Inconel 625, Hastelloy C-276, titanium (Ti) commercially pure (CP), Ti 6Al-4V, extra-low interstitial (ELI) Ti 6Al-4V, and Cronidur 30. In that evaluation, most specimens were exposed for a year. The results of that evaluation were published in NASA/TM-2015-218206, entitled "Stress Corrosion Evaluation of Various Metallic Materials for the International Space Station Water Recycling System,"1 available at the NASA Scientific and Technical Information program web page: http://www.sti.nasa.gov. Nitinol 60 was added to the test program in 2014.

Unified constitutive material models for nonlinear finite-element structural analysis. [gas turbine engine blades and vanes

NASA Technical Reports Server (NTRS)

Kaufman, A.; Laflen, J. H.; Lindholm, U. S.

1985-01-01

Unified constitutive material models were developed for structural analyses of aircraft gas turbine engine components with particular application to isotropic materials used for high-pressure stage turbine blades and vanes. Forms or combinations of models independently proposed by Bodner and Walker were considered. These theories combine time-dependent and time-independent aspects of inelasticity into a continuous spectrum of behavior. This is in sharp contrast to previous classical approaches that partition inelastic strain into uncoupled plastic and creep components. Predicted stress-strain responses from these models were evaluated against monotonic and cyclic test results for uniaxial specimens of two cast nickel-base alloys, B1900+Hf and Rene' 80. Previously obtained tension-torsion test results for Hastelloy X alloy were used to evaluate multiaxial stress-strain cycle predictions. The unified models, as well as appropriate algorithms for integrating the constitutive equations, were implemented in finite-element computer codes.

Giant-Magnetoresistance(GMR) Siegel KEY FIRST Experimental Discovery Decade-Earlier PRE-``Fert"-``Gruenberg" in Nuc"el"ar ``Super"alloys: Science?;``SEANCE!!!; Ethics?; SHMETHICS!!!

NASA Astrophysics Data System (ADS)

Hoffman, R.; Siegel, E.

2010-03-01

(So MIScalled) ``Fert"-``Grunberg"[PRL(1988;1989)] GMR 2007 physics Nobel/Wolf/Japan-Prizes VS. decade-earlier(1973-1977) KEY FIRST Siegel at:Westin"kl"ouse/PSEG/IAEA/ABB[google:``Martin Ebner"(94-04) in financial media]/Vattenfall/Wallenbergs/nuc"el"ar-DoE Labs[at flickr.com, search on ``Giant- Magnotoresistance''; find: Intl.Conf.Mag.Alloys & Oxides(ICMAO), Haifa(Aug./1977); J.Mag.Mag.Mtls,(JMMM)7,312(1978)``unavailable: not yet scanned''/modified(last R(H) GMR Figs(7;8) deleted!!!) on JMMM/Reed-Elsevier website until 7/29/08 conveniently one- half-year after last (Nobel)award(12/2007); conveniently effectively deleted!!!; google: ``If Leaks Could Kill''; many APS/MRS Mtgs(1970s)<<<1988/1989] decade-earlier GMR: (1978)<<< (1988); 1988-1978 =10 years = one full decadeprecedence!!!] first experimental discovery in (so MIScalled) ``super''alloys [182/82, Hastelloy-X, 600, 690(!!!), Stainless-Steels: ANY/ALL!!!] generic endemic Wigner's[JAP,17,857(1946)]- disease/Ostwald-ripening/spinodal-decomposition/overageing- embrittlement/ thermo-mechanical-INstability!

Koch–Haaf reaction of adamantanols in an acid-tolerant hastelloy-made microreactor

PubMed Central

Mukai, Yu

2011-01-01

Summary The Koch–Haaf reaction of adamantanols was successfully carried out in a microflow system at room temperature. By combining an acid-tolerant hastelloy-made micromixer, a PTFE tube, and a hastelloy-made microextraction unit, a packaged reaction-to-workup system was developed. By means of the present system, the multigram scale synthesis of 1-adamantanecarboxylic acid was achieved in ca. one hour operation. PMID:21977213

Vaccination with multimeric recombinant VP28 induces high protection against white spot syndrome virus in shrimp.

PubMed

Taengchaiyaphum, Suparat; Nakayama, Hideki; Srisala, Jiraporn; Khiev, Ratny; Aldama-Cano, Diva January; Thitamadee, Siripong; Sritunyalucksana, Kallaya

2017-11-01

To improve the efficacy of WSSV protection, multimeric (tetrameric) recombinant VP28 (4XrVP28) was produced and tested in comparison with those of monomeric VP28 (1XrVP28). In vitro binding of either 1XrVP28 or 4XrVP28 to shrimp hemocyte surface was evident as early as 10 min after protein inoculation. Similar results were obtained in vivo when shrimp were injected with recombinant proteins that the proteins bound to the hemocyte surface could be detected since 5 min after injection. Comparison of the WSSV protection efficiencies of 1XrVP28 or 4XrVP28 were performed by injection the purified 1XrVP28 or 4XrVP28 (22.5 μg/shrimp) and WSSV inoculum (1000 copies/shrimp) into shrimp. At 10 dpi, while shrimp injected with WSSV inoculum reached 100% mortality, shrimp injected with 1XrVP28 + WSSV or 4XrVP28 + WSSV showed relative percent survival (RPS) of 67% and 81%, respectively. PCR quantification revealed high number of WSSV in the moribund shrimp of WSSV- and 1XrVP28+WSSV-injected group. In contrast, lower number of WSSV copies were found in the survivors both from 1XrVP28+WSSV- or 4XrVP28+WSSV- injected groups. Histopathological analysis demonstrated the WSSV infected lesions found in the moribund from WSSV-infected group and 1XrVP28+WSSV-injected group, but less or none in the survivors. ELISA demonstrated that 4XrVP28 exhibited higher affinity binding to rPmRab7, a WSSV binding protein essential for WSSV entry to the cell than 1XrVP28. Taken together, the protection against WSSV in shrimp could be improved by application of multimeric rVP28. Copyright © 2017 Elsevier Ltd. All rights reserved.

Elevated temperature biaxial fatigue

NASA Technical Reports Server (NTRS)

Jordan, E. H.

1984-01-01

A three year experimental program for studying elevated temperature biaxial fatigue of a nickel based alloy Hastelloy-X has been completed. A new high temperature fatigue test facility with unique capabilities has been developed. Effort was directed toward understanding multiaxial fatigue and correlating the experimental data to the existing theories of fatigue failure. The difficult task of predicting fatigue lives for non-proportional loading was used as an ultimate test for various life prediction methods being considered. The primary means of reaching improved undertanding were through several critical non-proportional loading experiments. It was discovered that the cracking mode switched from primarily cracking on the maximum shear planes at room temperature to cracking on the maximum normal strain planes at 649 C.

The NASA Lewis Strain Gauge Laboratory: An update

NASA Technical Reports Server (NTRS)

Hobart, H. F.

1986-01-01

Efforts continue in the development and evaluation of electrical resistance strain gauges of the thin film and small diameter wire type. Results obtained early in 1986 on some Chinese gauges and Kanthal A-1 gauges mounted on a Hastelloy-X substrate are presented. More recent efforts include: (1) the determination of the uncertainty in the ability to establish gauge factor, (2) the evaluation of sputtered gauges that were fabricated at Lewis, (3) an investigation of the efficacy of dual element temperature compensated gauges when using strain gauge alloys having large thermal coefficients of resistance, and (4) an evaluation of the practical methods of stabilizing gauges whose apparent strain is dependent on cooling rate (e.g., FeCrAl gauges).

Materials Testing for an Accelerator-Driven Subcritical Molten Salt Fission System: A look at the Materials Science of Molten Salt Corrosion

NASA Astrophysics Data System (ADS)

Sooby, Elizabeth; Balachandran, Shreyas; Foley, David; Hartwig, Karl; McIntyre, Peter; Phongikaroon, Supathorn; Pogue, Nathaniel; Simpson, Michael; Tripathy, Prabhat

2011-10-01

For an accelerator-driven subcritical molten salt fission core to survive its 50+ year fuel life, the primary vessel, heat exchanger, and various internal components must be made of materials that resist corrosion and radiation damage in a high-temperature environment, (500-800 C). An experimental study of the corrosion behavior of candidate metals in contact with molten salt is being conducted at the Center for Advanced Energy Studies. Initial experiments have been run on Nb, Ta, Ni, two zirconium alloys, Hastelloy-N, and a series of steel alloys to form a base line for corrosion in both chloride and bromide salt. Metal coupons were immersed in LiCl-KCl or LiBr-KBr at 700 C in an inert-atmosphere. Salt samples were extracted on a time schedule over a 24-hr period. The samples were analyzed using inductively coupled plasma-mass spectrometry to determine concentrations of metals from corrosion. Preliminary results will be presented.

Extremely high-rate, uniform dissolution of alloy C-22 in anhydrous organic solutions at room temperature

DOE PAGES

Schindelholz, Eric J.; Christie, Michael A.; Allwein, Shawn P.; ...

2016-06-21

During routine pharmaceutical development and scale-up work, severe corrosion of a Hastelloy Alloy C-22 filter dryer was observed after single, short (several hours) contact with the product slurry at room temperature. Initial investigations showed that the presence of both 2,3-dichloro-5,6-dicyano-1,4-benzoquinone (DDQ) and HCl was sufficient in an acetonitrile solution to cause rapid corrosion of C-22. More detailed mass loss studies showed initial corrosion rates exceeding25 mm/year that then decreased over several hours to steady state rates of 3-5 mm/year. The corrosion was highly uniform. Electrochemical measurements demonstrated that although C-22 is spontaneously passive in acetonitrile solution, the presence of HClmore » leads to the development of a transpassive region. Furthermore, DDQ is a sufficiently strong oxidizer, particularly in acidic solutions, to polarize the C-22 well into the transpassive region, leading to the observed high corrosion rates.« less

Halogen Containing Gases as Lubricants for Crystallized Glass Ceramic Metal Combinations at Temperatures to 1500 F

NASA Technical Reports Server (NTRS)

Buckley, Donald H.; Johnson, Robert L.

1960-01-01

Pyroceram 9608 (a crystallized glass ceramic) has been considered for use in high-temperature bearing and seal applications. One of the problems encountered with Pyroceram is the lack of availability of lubricants for the temperature range in which this material becomes practical. Experiments were conducted with Pyroceram sliding on various nickel- and cobalt-base alloys using reactive halogen-containing gases as lubricants. Friction and wear data were obtained as a function of sliding velocity and temperature. Studies were made with a hemispherical rider (3/16-in. rad., Pyroceram 9608) sliding in a circumferential path on the flat surface of a rotating disk (2(1/2) in. diam., nickel- or cobalt-base alloys). The specimens were run in an atmosphere of the various gases with a load of 1200 grams, a sliding velocity of 3200 feet per minute, and temperatures from 75 to 1500 F. The gas CF2Br-CF2Br was found to be an effective lubricant for Pyroceram 9608 sliding on Hastelloy R-235 and Inconel X up to 1400 F. The gas CF2Cl-CF2Cl provided effective lubrication for Pyroceram sliding on various cobalt-base alloys at 1000 F.

Predictors of Treatment with Duloxetine or Venlafaxine XR among Adult Patients Treated for Depression in Primary Care Practices in the United Kingdom

PubMed Central

Shi, Nianwen; Durden, Emily; Torres, Amelito; Cao, Zhun; Happich, Michael

2012-01-01

Background. Knowledge about real-world use of duloxetine and venlafaxine XR to treat depression in the UK is limited. Aims. To identify predictors of duloxetine or venlafaxine XR initiation. Method. Adult depressed patients who initiated duloxetine or venlafaxine XR between January 1, 2006 and September 30, 2007 were identified in the UK's General Practice Research Database. Demographic and clinical predictors of treatment initiation with duloxetine and venlafaxine XR were identified using logistic regression. Results. Patients initiating duloxetine (n = 909) were 4 years older than venlafaxine XR recipients (n = 1286). Older age, preexisting unexplained pain, respiratory disease, and pre-period use of anticonvulsants, opioids, and antihyperlipidemics were associated with increased odds of initiating duloxetine compared to venlafaxine XR. Pre-period anxiety disorder was associated with decreased odds of receiving duloxetine. Conclusion. Initial treatment choice with duloxetine versus venlafaxine XR was primarily driven by patient-specific mental and medical health characteristics. General practitioners in the UK favor duloxetine over venlafaxine XR when pain conditions coexist with depression. PMID:22720149

Weld procedure produces quality welds for thick sections of Hastelloy-X

NASA Technical Reports Server (NTRS)

Flens, F. J.; Fletcher, C. W.; Glasier, L. F., Jr.

1967-01-01

Welding program produces premium quality, multipass welds in heavy tube sections of Hastelloy-X. It develops semiautomatic tungsten/inert gas procedures, weld wire procurement specifications material weld properties, welder-operator training, and nondestructive testing inspection techniques and procedures.

Application of an Uncoupled Elastic-plastic-creep Constitutive Model to Metals at High Temperature

NASA Technical Reports Server (NTRS)

Haisler, W. E.

1983-01-01

A uniaxial, uncoupled constitutive model to predict the response of thermal and rate dependent elastic-plastic material behavior is presented. The model is based on an incremental classicial plasticity theory extended to account for thermal, creep, and transient temperature conditions. Revisions to he combined hardening rule of the theory allow for better representation of cyclic phenomenon including the high rate of strain hardening upon cyclic reyield and cyclic saturation. An alternative approach is taken to model the rate dependent inelastic deformation which utilizes hysteresis loops and stress relaxation test data at various temperatures. The model is evaluated and compared to experiments which involve various thermal and mechanical load histories on 5086 aluminum alloy, 304 stainless steel and Hastelloy-X.

Critical experiments of the self-consistent model for polycrystalline Hastelloy-X

NASA Technical Reports Server (NTRS)

Shi, Shixiang; Walker, Kevin P.; Jordan, Eric H.

1991-01-01

A viscoplastic constitutive model is presented for the estimation of the overall mechanical response of Hastelloy-X polycrystalline metals from a knowledge of single crystal behavior. The behavior of polycrystal is derived from that of single crystals using a self-consistent formulation. The single crystal behavior which has been used was developed by summing postulated slip on crystallographic slip systems. The plasticity and creep are treated coupledly using unified viscoplastic model which includes the interaction effects between rapid and slow deformation at elevated temperature. The validity of the model is directly tested by experiments on Hastelloy-X in both single crystal and polycrystalline versions.

A folded viral noncoding RNA blocks host cell exoribonucleases through a conformationally dynamic RNA structure.

PubMed

Steckelberg, Anna-Lena; Akiyama, Benjamin M; Costantino, David A; Sit, Tim L; Nix, Jay C; Kieft, Jeffrey S

2018-06-19

Folded RNA elements that block processive 5' → 3' cellular exoribonucleases (xrRNAs) to produce biologically active viral noncoding RNAs have been discovered in flaviviruses, potentially revealing a new mode of RNA maturation. However, whether this RNA structure-dependent mechanism exists elsewhere and, if so, whether a singular RNA fold is required, have been unclear. Here we demonstrate the existence of authentic RNA structure-dependent xrRNAs in dianthoviruses, plant-infecting viruses unrelated to animal-infecting flaviviruses. These xrRNAs have no sequence similarity to known xrRNAs; thus, we used a combination of biochemistry and virology to characterize their sequence requirements and mechanism of stopping exoribonucleases. By solving the structure of a dianthovirus xrRNA by X-ray crystallography, we reveal a complex fold that is very different from that of the flavivirus xrRNAs. However, both versions of xrRNAs contain a unique topological feature, a pseudoknot that creates a protective ring around the 5' end of the RNA structure; this may be a defining structural feature of xrRNAs. Single-molecule FRET experiments reveal that the dianthovirus xrRNAs undergo conformational changes and can use "codegradational remodeling," exploiting the exoribonucleases' degradation-linked helicase activity to help form their resistant structure; such a mechanism has not previously been reported. Convergent evolution has created RNA structure-dependent exoribonuclease resistance in different contexts, which establishes it as a general RNA maturation mechanism and defines xrRNAs as an authentic functional class of RNAs.

Dynamic evaluation of low-temperature metal-supported solid oxide fuel cell oriented to auxiliary power units

NASA Astrophysics Data System (ADS)

Wang, Zhenwei; Berghaus, Jörg Oberste; Yick, Sing; Decès-Petit, Cyrille; Qu, Wei; Hui, Rob; Maric, Radenka; Ghosh, Dave

A metal-supported solid oxide fuel cell (SOFC) composed of a Ni-Ce 0.8Sm 0.2O 2- δ (Ni-SDC) cermet anode and an SDC electrolyte was fabricated by suspension plasma spraying on a Hastelloy X substrate. The cathode, an Sm 0.5Sr 0.5CoO 3 (SSCo)-SDC composite, was screen-printed and fired in situ. The dynamic behaviour of the cell was measured while subjected to complete fuel shutoff and rapid start-up cycles, as typically encountered in auxiliary power units (APU) applications. A promising performance - with a maximum power density (MPD) of 0.176 W cm -2 at 600 °C - was achieved using humidified hydrogen as fuel and air as the oxidant. The cell also showed excellent resistance to oxidation at 600 °C during fuel shutoff, with only a slight drop in performance after reintroduction of the fuel. The Cr and Mn species in the Hastelloy X alloy appeared to be preferentially oxidized while the oxidation of nickel in the metallic substrate was temporarily alleviated. In rapid start-up cycles with a heating rate of 60 °C min -1, noticeable performance deterioration took place in the first two thermal cycles, and then continued at a much slower rate in subsequent cycles. A postmortem analysis of the cell suggested that the degradation was mainly due to the mismatch of the thermal expansion coefficient across the cathode/electrolyte interface.

Analyzing the effect of cutting parameters on surface roughness and tool wear when machining nickel based hastelloy - 276

NASA Astrophysics Data System (ADS)

Khidhir, Basim A.; Mohamed, Bashir

2011-02-01

Machining parameters has an important factor on tool wear and surface finish, for that the manufacturers need to obtain optimal operating parameters with a minimum set of experiments as well as minimizing the simulations in order to reduce machining set up costs. The cutting speed is one of the most important cutting parameter to evaluate, it clearly most influences on one hand, tool life, tool stability, and cutting process quality, and on the other hand controls production flow. Due to more demanding manufacturing systems, the requirements for reliable technological information have increased. For a reliable analysis in cutting, the cutting zone (tip insert-workpiece-chip system) as the mechanics of cutting in this area are very complicated, the chip is formed in the shear plane (entrance the shear zone) and is shape in the sliding plane. The temperature contributed in the primary shear, chamfer and sticking, sliding zones are expressed as a function of unknown shear angle on the rake face and temperature modified flow stress in each zone. The experiments were carried out on a CNC lathe and surface finish and tool tip wear are measured in process. Machining experiments are conducted. Reasonable agreement is observed under turning with high depth of cut. Results of this research help to guide the design of new cutting tool materials and the studies on evaluation of machining parameters to further advance the productivity of nickel based alloy Hastelloy - 276 machining.

Development of constitutive models for cyclic plasticity and creep behavior of super alloys at high temperature

NASA Technical Reports Server (NTRS)

Haisler, W. E.

1983-01-01

An uncoupled constitutive model for predicting the transient response of thermal and rate dependent, inelastic material behavior was developed. The uncoupled model assumes that there is a temperature below which the total strain consists essentially of elastic and rate insensitive inelastic strains only. Above this temperature, the rate dependent inelastic strain (creep) dominates. The rate insensitive inelastic strain component is modelled in an incremental form with a yield function, blow rule and hardening law. Revisions to the hardening rule permit the model to predict temperature-dependent kinematic-isotropic hardening behavior, cyclic saturation, asymmetric stress-strain response upon stress reversal, and variable Bauschinger effect. The rate dependent inelastic strain component is modelled using a rate equation in terms of back stress, drag stress and exponent n as functions of temperature and strain. A sequence of hysteresis loops and relaxation tests are utilized to define the rate dependent inelastic strain rate. Evaluation of the model has been performed by comparison with experiments involving various thermal and mechanical load histories on 5086 aluminum alloy, 304 stainless steel and Hastelloy X.

Electrochemical, Polarization, and Crevice Corrosion Testing of Nitinol 60, A Supplement to the ECLSS Sustaining Materials Compatibility Study

NASA Technical Reports Server (NTRS)

Lee, R. E.

2016-01-01

In earlier trials, electrochemical test results were presented for six noble metals evaluated in test solutions representative of waste liquids processed in the Environmental Control and Life Support System (ECLSS) aboard the International Space Station (ISS). Subsequently, a seventh metal, Nitinol 60, was added for evaluation and subjected to the same test routines, data analysis, and theoretical methodologies. The previous six test metals included three titanium grades, (commercially pure, 6Al-4V alloy and 6Al-4V low interstitial alloy), two nickel-chromium alloys (Inconel(RegisteredTrademark) 625 and Hastelloy(RegisteredTrademark) C276), and one high-tier stainless steel (Cronidur(RegisteredTrademark) 30). The three titanium alloys gave the best results of all the metals, indicating superior corrosive nobility and galvanic protection properties. For this current effort, the results have clearly shown that Nitinol 60 is almost as noble as titanium, being very corrosion-resistant and galvanically compatible with the other six metals electrochemically and during long-term exposure. is also quite noble as it is very corrosion resistant and galvanically compatible with the other six metals from both an electrochemical perspective and long-term crevice corrosion scenario. This was clearly demonstrated utilizing the same techniques for linear, Tafel and cyclic polarization, and galvanic coupling of the metal candidate as was done for the previous study. The high nobility and low corrosion susceptibility for Nitinol 60 appear to be intermediate to the nickel/chromium alloys and the titanium metals with indications that are more reflective of the titanium metals in terms of general corrosion and pitting behavior.

Bioequivalence of saxagliptin/metformin extended-release (XR) fixed-dose combination tablets and single-component saxagliptin and metformin XR tablets in healthy adult Chinese subjects.

PubMed

Gummesson, Anders; Li, Haiyan; Gillen, Michael; Xu, John; Niazi, Mohammad; Hirshberg, Boaz

2014-11-01

As compared with individual tablets, saxagliptin/metformin extended-release (XR) fixed-dose combination (FDC) tablets offer the potential for increased patient compliance with the convenience of once daily dosing. The aim of the present study was to show that the FDC of saxagliptin and metformin XR is bioequivalent to co-administration of the individual components when given to Chinese subjects residing in China. This was a randomized, open-label, single-dose, two-period, cross-over pharmacokinetic study in two cohorts of healthy adult Chinese male subjects (n = 32 in each cohort) under fed conditions. In cohort 1, the pharmacokinetic properties of a saxagliptin/metformin XR 5/500 mg FDC tablet were compared with those of co-administration of a 5 mg saxagliptin tablet and a 500 mg metformin XR tablet. In cohort 2, the pharmacokinetic properties of a saxagliptin/metformin XR 5/1,000 mg FDC tablet were compared with those of co-administration of a 5 mg saxagliptin tablet and 2 × 500 mg metformin XR tablets. The two cohorts were independent of each other with respect to treatment and results. The pharmacokinetic properties of the active metabolite of saxagliptin (5-hydroxy-saxagliptin), as well as the safety and tolerability of each treatment, were also evaluated. For both cohorts, saxagliptin and metformin in the FDCs were bioequivalent to the individual components, as the limits of the 90 % confidence intervals of the geometric least squares mean ratios were contained within the 80-125 % bioequivalence limits for the area under the plasma concentration-time curve parameters and within the 70-143 % bioequivalence limits for the maximum plasma concentration. Similar exposures of 5-hydroxy-saxagliptin were observed with the two treatment regimens within each cohort. Co-administration of saxagliptin and metformin XR was generally safe and well tolerated as the FDCs or as individual tablets. Saxagliptin/metformin XR 5/500 mg and saxagliptin/metformin XR 5/1,000 mg FDCs were bioequivalent to individual tablets of saxagliptin and metformin XR of the same strengths and were generally well tolerated. These results in healthy Chinese subjects are consistent with those of previous assessments of saxagliptin/metformin XR FDC in the saxagliptin clinical development programme.

Specific Heat and Thermal Diffusivity of YBCO Coated Conductors

NASA Astrophysics Data System (ADS)

Naito, Tomoyuki; Fujishiro, Hiroyuki; YasuhisaYamamura; Saito, Kazuya; Okamoto, Hiroshi; Hayashi, Hidemi; Gosho, Yoshihiro; Ohkuma, Takeshi; Shiohara, Yuh

We have measured the temperature dependence of specific heat,C(T), for Ag deposited YBCO coated conductor (YCC),YCC reinforced by a thin Cutape (YCC-Cu), andthe Hastelloy substrate with buffer layer. C(T) of HastelloyC-276 with buffer layer agrees well with the reported oneof HastelloyC-276, indicating that the contribution of the buffer layer to the measured C(T) is negligibly small. C(T)of both YCC and YCC-Cu tapes was successfully reproduced by the simple sum rule using the C(T) values reported for Hastelloy, Ag and Cu. The results demonstrate that C(T) of various YCC tapes can be estimated using the reported C(T)of constitutional materials. The estimated thermal diffusivity, a = K/C, at 300K of YCC, which was estimated using the thermal conductivity, K, did not agree with the reported a of Ag. This resultwas in consistent with the fact that the applied heat flew through the Aglayer, suggesting that a relation of a = K/Cfor homogeneous material cannot be applicable for the layered material such as YCC.

Long-Term Tolerability and Effectiveness of Once-Daily Mixed Amphetamine Salts (Adderall XR) in Children with ADHD

ERIC Educational Resources Information Center

McGough, James J.; Biederman, Joseph; Wigal, Sharon B.; Lopez, Frank A.; McCracken, James T.; Spencer, Thomas; Zhang, Yuxin; Tulloch, Simon J.

2005-01-01

Objective: To evaluate the long-term tolerability and effectiveness of extended-release mixed amphetamine salts (MAS XR; Adderall XR[R]) in children with attention-deficit/hyperactivity disorder (ADHD). Method: This was a 24-month, multicenter, open-label extension of TWO placebo-controlled studies of MAS XR in children with ADHD aged 6 to 12…

Effectiveness, safety and feasibility of extended-release naltrexone for opioid dependence: a 9-month follow-up to a 3-month randomized trial.

PubMed

Solli, Kristin Klemmetsby; Latif, Zill-E-Huma; Opheim, Arild; Krajci, Peter; Sharma-Haase, Kamni; Benth, Jūratė Šaltytė; Tanum, Lars; Kunoe, Nikolaj

2018-05-28

This is a follow-up study of a previously published randomized clinical trial conducted in Norway that compared extended-release naltrexone (XR-NTX) to buprenorphine-naloxone (BP-NLX) over 3 months. At the conclusion of the trial, participants were offered their choice of study medication for an additional 9 months. While BP-NLX was available at no cost through opioid maintenance treatment programmes, XR-NTX was available only through study participation, accounting for why almost all participants chose XR-NTX in the follow-up. The aim of this follow-up study was to compare differences in outcome between adults with opioid dependence continuing XR-NTX and those inducted on XR-NTX for a 9-month period, on measures of effectiveness, safety and feasibility. In this prospective cohort study, participants were either continuing XR-NTX, changed from BP-NLX to XR-NTX or re-included into the study and inducted on XR-NTX treatment. Five urban, out-patient addiction clinics in Norway. Opioid-dependent adults continuing (n = 54) or inducted on (n = 63) XR-NTX. XR-NTX administrated as intramuscular injections (380 mg) every fourth week. Data on retention, use of heroin and other illicit substances, opioid craving, treatment satisfaction, addiction-related problems and adverse events were reported every fourth week. Nine-month follow-up completion rates were 51.9% among participants continuing XR-NTX in the follow-up and 47.6% among those inducted on XR-NTX. Opioid abstinence rates were, respectively, 53.7 and 44.4%. No significant group differences were found in use of heroin and other opioids. Opioid-dependent individuals who elect to switch from buprenorphine-naltrexone treatment after 3 months to extended-release naltrexone treatment for 9 months appear to experience similar treatment completion and abstinence rates and similar adverse event profiles to individuals who had been on extended-release naltrexone from the start of treatment. © 2018 Society for the Study of Addiction.

Do withdrawal-like symptoms mediate increased marijuana smoking in individuals treated with venlafaxine-XR?

PubMed

Kelly, Meredith A; Pavlicova, Martina; Glass, Andrew; Mariani, John J; Bisaga, Adam; Sullivan, Maria A; Nunes, Edward V; Levin, Frances R

2014-11-01

Cannabis-dependent participants with depressive disorder are less likely to achieve abstinence with venlafaxine-XR (VEN-XR) treatment. Individuals on VEN-XR reported more severe withdrawal, despite not reducing their smoking behavior. We hypothesized that withdrawal-like symptoms, likely medication side effects, led to continued marijuana smoking in this group. We conducted a secondary analysis using Marijuana Withdrawal Checklist (MWC) scores and urine THC to test whether severity of withdrawal-like symptoms mediates the relationship between VEN-XR treatment and continued marijuana smoking. We included 103 participants (VEN-XR=51, Placebo=52). Marijuana use was dichotomized into smoking (THC>100 ng/ml) and non-smoking (THC ≤ 100 ng/ml) weeks. MWC scores were obtained weekly. We used three models in a regression based mediation analysis. The estimated risk of smoking marijuana was greater for individuals on VEN-XR in weeks 7-9, even when controlling for MWC scores (week 7 Risk Difference (RD)=0.11, p=0.034; week 8 RD=0.20, p=0.014), and higher scores mediated this effect. In weeks 10 and 11, the estimated effect was stronger (week 10 RD=0.03, p=0.380; week 11 RD=0.07, p=0.504), and worse withdrawal-like symptoms more fully accounted for continued marijuana smoking in the VEN-XR group, according to the models. Individuals treated with VEN-XR had more severe withdrawal-like symptoms, which mediated their continued marijuana smoking. Noradrenergic agents, such as VEN-XR, may negatively impact treatment outcomes in cannabis-dependent patients attempting to reduce or stop their use. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Do withdrawal-like symptoms mediate increased marijuana smoking in individuals treated with venlafaxine-XR?

PubMed Central

Kelly, Meredith A.; Pavlicova, Martina; Glass, Andrew; Mariani, John J.; Bisaga, Adam; Sullivan, Maria A.; Nunes, Edward V.; Levin, Frances R.

2014-01-01

Background and aims Cannabis-dependent participants with depressive disorder are less likely to achieve abstinence with venlafaxine-XR (VEN-XR) treatment. Individuals on VEN-XR reported more severe withdrawal, despite not reducing their smoking behavior. We hypothesized that withdrawal-like symptoms, likely medication side effects, led to continued marijuana smoking in this group. Methods We conducted a secondary analysis using Marijuana Withdrawal Checklist (MWC) scores and urine THC to test whether severity of withdrawal-like symptoms mediates the relationship between VEN-XR treatment and continued marijuana smoking. We included 103 participants (VEN-XR = 51, Placebo = 52). Marijuana use was dichotomized into smoking (THC > 100 ng/ml) and non-smoking (THC ≤ 100 ng/ml) weeks. MWC scores were obtained weekly. We used three models in a regression based mediation analysis. Results The estimated risk of smoking marijuana was greater for individuals on VEN-XR in weeks 7–9, even when controlling for MWC scores (week 7 Risk Difference (RD) = 0.11, p = 0.034; week 8 RD = 0.20, p = 0.014), and higher scores mediated this effect. In weeks 10 and 11, the estimated effect was stronger (week 10 RD = 0.03, p = 0.380; week 11 RD = 0.07, p = 0.504), and worse withdrawal-like symptoms more fully accounted for continued marijuana smoking in the VEN-XR group, according to the models. Conclusions Individuals treated with VEN-XR had more severe withdrawal-like symptoms, which mediated their continued marijuana smoking. Noradrenergic agents, such as VEN-XR, may negatively impact treatment outcomes in cannabis-dependent patients attempting to reduce or stop their use. PMID:25283697

Response surface methodology as an approach to determine the optimal activities of xylose reductase and xylitol dehydrogenase enzymes from Candida Mogii.

PubMed

Mayerhoff, Zea D V L; Roberto, Inês C; Franco, Telma T

2006-05-01

A central composite experimental design leading to a set of 16 experiments with different combinations of pH and temperature was performed to attain the optimal activities of xylose reductase (XR) and xylitol dehydrogenase (XDH) enzymes from Candida mogii cell extract. Under optimized conditions (pH 6.5 and 38 degrees C), the XR and XDH activities were found to be 0.48 U/ml and 0.22 U/ml, respectively, resulting in an XR to XDH ratio of 2.2. Stability, cofactor specificity and kinetic parameters of the enzyme XR were also evaluated. XR activity remained stable for 3 h under 4 and 38 degrees C and for 4 months of storage at -18 degrees C. Studies on cofactor specificity showed that only NADPH-dependent XR was obtained under the cultivation conditions employed. The XR present in C. mogii extracts showed a superior Km value for xylose when compared with other yeast strains. Besides, this parameter was not modified after enzyme extraction by aqueous two-phase system.

Extended-release naltrexone (XR-NTX) attenuates brain responses to alcohol cues in alcohol-dependent volunteers: a bold FMRI study.

PubMed

Lukas, Scott E; Lowen, Steven B; Lindsey, Kimberly P; Conn, Nina; Tartarini, Wendy; Rodolico, John; Mallya, Gopi; Palmer, Christopher; Penetar, David M

2013-09-01

Oral naltrexone reduces heavy drinking, but is less consistent as an abstinence promoter, whereas once-monthly extended-release naltrexone (XR-NTX) also maintains abstinence. The present study sought to determine if alcohol cue reactivity is attenuated by XR-NTX. Twenty-eight detoxified alcohol-dependent adult male and female volunteers received a single i.m. injection of either XR-NTX or placebo under double-blind conditions. An fMRI/cue reactivity procedure was conducted immediately before and two weeks after injection. At baseline, alcohol-related visual and olfactory cues elicited significant increases in orbital and cingulate gyri, inferior frontal and middle frontal gyri. Subsequently, brain activation was significantly altered in XR-NTX-treated individuals. These affected brain regions are associated with the integration of emotion, cognition, reward, punishment, and learning/memory, suggesting that XR-NTX attenuates the salience of alcohol-related cues. Such an effect on brain function may interrupt the processes associated with "slips" and relapse, which may account for XR-NTX's ability to maintain abstinence. Copyright © 2013 Elsevier Inc. All rights reserved.

Cation Binding to Xanthorhodopsin: Electron Paramagnetic Resonance and Magnetic Studies.

PubMed

Smolensky Koganov, Elena; Leitus, Gregory; Rozin, Rinat; Weiner, Lev; Friedman, Noga; Sheves, Mordechai

2017-05-04

Xanthorhodopsin (xR) is a member of the retinal protein family and acts as a proton pump in the cell membranes of the extremely halophilic eubacterium Salinibacter ruber. In addition to the retinal chromophore, xR contains a carotenoid, which acts as a light-harvesting antenna as it transfers 40% of the quanta it absorbs to the retinal. Our previous studies have shown that the CD and absorption spectra of xR are dramatically affected due to the protonation of two different residues. It is still unclear whether xR can bind cations. Electron paramagnetic resonance (EPR) spectroscopy used in the present study revealed that xR can bind divalent cations, such as Mn 2+ and Ca 2+ , to deionized xR (DI-xR). We also demonstrate that xR can bind 1 equiv of Mn 2+ to a high-affinity binding site followed by binding of ∼40 equiv in cooperative manner and ∼100 equiv of Mn 2+ that are weakly bound. SQUID magnetic studies suggest that the high cooperative binding of Mn 2+ cations to xR is due to the formation of Mn 2+ clusters. Our data demonstrate that Ca 2+ cations bind to DI-xR with a lower affinity than Mn 2+ , supporting the assumption that binding of Mn 2+ occurs through cluster formation, because Ca 2+ cations cannot form clusters in contrast to Mn 2+ .

Post-marketing experience with nevirapine extended release (XR) tablets: effectiveness and tolerability in a population-based cohort in British Columbia, Canada.

PubMed

Lepik, Katherine J; Yip, Benita; McGovern, Rachel A; Ding, Erin; Nohpal, Adriana; Watson, Birgit E; Toy, Junine; Akagi, Linda; Harrigan, P Richard; Moore, David M; Hogg, Robert S; Montaner, Julio S G; Barrios, Rolando

2015-01-01

Nevirapine 400 mg extended release tablets (nevirapine-XR) are a once-daily alternative to nevirapine 200 mg immediate release tablets (nevirapine-IR). Study objectives were to describe the effectiveness and tolerability of nevirapine-XR in clinical practice and, for patients who switched from once daily 2×200 mg nevirapine-IR to nevirapine-XR, compare virological suppression and plasma nevirapine concentrations during each treatment period. HIV-1-infected adults entered the study cohort if they initiated nevirapine-XR in British Columbia (BC) Canada between 1 April 2012 and 30 September 2012 and were followed until 30 September 2013. Demographic and clinical variables were abstracted from the BC Centre for Excellence in HIV/AIDS databases. Patients who switched from once daily nevirapine-IR to nevirapine-XR were monitored for 6 months pre- and post-switch with comparison of virological suppression (McNeamer's test) and median random plasma nevirapine concentrations (Wilcoxon-Mann-Whitney test) in each period. The 536 nevirapine-XR-treated patients were 96% male, median (IQR) age 49.9 (44.0-56.9) years. Median follow-up was 15.6 (14.7-16.5) months, with 474/536 (88%) maintaining virological suppression. Emergent drug resistance developed in 5/536 (1%), adverse drug reactions in 17/536 (3%) and, although 31/536 (6%) reported 'whole' tablets in their stools, this was not associated with adverse outcomes. Among the 305 patients who switched from nevirapine-IR to nevirapine-XR, median (IQR) random plasma nevirapine concentration was higher during nevirapine-IR 5,000 (3,690-6,090) ng/ml than nevirapine-XR 3,930 (3,050-5,150) ng/ml (P<0.001), but there was no difference in virological suppression, 89% and 87% respectively (P=0.414). This post-marketing study affirms the effectiveness and tolerability of nevirapine-XR as an alternative to nevirapine-IR in adults.

Technical Note: Response time evolution of XR-QA2 GafChromic™ film models.

PubMed

Aldelaijan, Saad; Tomic, Nada; Papaconstadopoulos, Pavlos; Schneider, James; Seuntjens, Jan; Shih, Shelley; Lewis, David; Devic, Slobodan

2018-01-01

To evaluate the response of the newest XR-QA2 GafChromic™ film model in terms of postexposure signal growth and energy response in comparison with the older XR-QA (Version 2) model. Pieces of film were irradiated to air kerma in air values up to 12 cGy with several beam qualities (5.3-8.25 mm Al) commonly used for CT scanning. Film response was scored in terms of net reflectance from scanned film images at various points in time postirradiation ranging from 1 to 7 days and 5 months postexposure. To reconstruct the measurement signal changes with postirradiation delay, we irradiated one film piece and then scanned it at different point times starting from 2" min and up to 3 days postexposure. For all beam qualities and dose range investigated, it appears that the XR-QA2 film signal completely saturated after 15 h. Compared to 15 h postirradiation scanning time, the observed variation in net reflectance were 3%, 2%, and 1% for film scanned 2" min, 20 min, and 3 h after exposure, respectively, which is well within the measurement uncertainty of the XR-QA2 based reference radiochromic film dosimetry system. A comparison between the XR-QA (Version 2) and the XR-QA2 film response after several months (relative to their responses after 24 h) show differences in up to 8% and 1% for each film model respectively. The replacement of cesium bromide in the older XR-QA (Version 2) film model with bismuth oxide in the newer XR-QA2 film, while keeping the same single sensitive layer structure, lead to a significantly more stable postexposure response. © 2017 American Association of Physicists in Medicine.

Employment-based reinforcement of adherence to an FDA approved extended release formulation of naltrexone in opioid-dependent adults: a randomized controlled trial.

PubMed

DeFulio, Anthony; Everly, Jeffrey J; Leoutsakos, Jeannie-Marie S; Umbricht, Annie; Fingerhood, Michael; Bigelow, George E; Silverman, Kenneth

2012-01-01

Naltrexone provides excellent opioid blockade, but its clinical utility is limited because opioid-dependent patients typically refuse it. An injectable suspension of naltrexone for extended release (XR-NTX) was recently approved by the FDA for treatment of opioid dependence. XR-NTX treatment may require concurrent behavioral intervention to maximize adherence and effectiveness, thus we sought to evaluate employment-based reinforcement as a method of improving adherence to XR-NTX in opiate dependent adults. Opioid-dependent adults (n=38) were detoxified and inducted onto oral naltrexone, then randomly assigned to contingency or prescription conditions. Participants received up to six doses of XR-NTX at four-week intervals. All participants could earn vouchers for attendance and performance at a therapeutic workplace. Contingency participants were required to accept XR-NTX injections to access the workplace and earn vouchers. Prescription participants could earn vouchers independent of their acceptance of XR-NTX injections. Contingency participants accepted significantly more naltrexone injections than prescription participants (87% versus 52%, p=.002), and were more likely to accept all injections (74% versus 26%, p=.004). Participants in the two conditions provided similar percentages of samples negative for opiates (72% versus 65%) and for cocaine (58% versus 54%). Opiate positivity was significantly more likely when samples were also cocaine positive, independent of naltrexone blockade (p=.002). Long-term adherence to XR-NTX in unemployed opiate dependent adults is low under usual care conditions. Employment-based reinforcement can maintain adherence to XR-NTX. Ongoing cocaine use appears to interfere with the clinical effectiveness of XR-NTX on opiate use. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

A Randomized, Placebo-Controlled Pilot Study of Quetiapine-XR Monotherapy or Adjunctive Therapy to Antidepressant in Acute Major Depressive Disorder with Current Generalized Anxiety Disorder.

PubMed

Li, Ranran; Wu, Renrong; Chen, Jun; Kemp, David E; Ren, Ming; Conroy, Carla; Chan, Philip; Serrano, Mary Beth; Ganocy, Stephen J; Calabrese, Joseph R; Gao, Keming

2016-03-01

To pilot efficacy and safety data of quetiapine-XR monotherapy or adjunctive therapy to antidepressant(s) in the acute treatment of MDD with current generalized anxiety disorder (GAD). The Mini International Neuropsychiatric Interview was used to ascertain the diagnosis of DSM-IV Axis I disorders. Eligible patients were randomly assigned to quetiapine-XR or placebo for up to 8 weeks. Changes from baseline to endpoint in Hamilton Depression Rating Scale-17 items (HAMD-17), Hamilton Anxiety Rating Scale (HAM-A), Clinical Global Impression-Severity (CGI-S), Quick Inventory of Depression Symptomatology-16 items Self-Report (QIDS-16-SR) total scores, and other outcome measures were analyzed with the last observation carried forward strategy and/or mixed-effects modeling for repeated measures. Of the 34 patients screened, 23 patients were randomized to receive quetiapine-XR (n = 11) or placebo (n = 12), with 5 and 4 completing the study, respectively. The mean dose of quetiapine-XR was 154 ± 91 mg/d. The change from baseline to endpoint in the total scores of HAMD-17, HAM-A, QIDS-16-SR, and CGI-S were significant in the quetiapine-XR group, but only the change in HAM-A total score was significant in the placebo group. The differences in these changes between the two groups were only significant in CGI-S scores, with the rest of numerical larger in the quetiapine-XR group. The most common side effects from quetiapine-XR were dry mouth, somnolence/sedation, and fatigue. In this pilot study, quetiapine-XR was numerically superior to placebo in reducing depressive and anxiety symptoms in patients with MDD and current GAD. Large sample studies are warranted to support or refute these preliminary findings.

FRAUD/SABOTAGE Killing Nuclear-Reactors!!! ``Super"alloys GENERIC ENDEMIC Wigner's-Disease IN-stability!!!

NASA Astrophysics Data System (ADS)

Asphahani, Aziz; Siegel, Sidney; Siegel, Edward

2010-03-01

Siegel [[J.Mag.Mag.Mtls.7,312(78); PSS(a)11,45(72); Semis.& Insuls.5(79)] (at: ORNL, ANS, Westin``KL"ouse, PSEG, IAEA, ABB) warning of old/new nuclear-reactors/spent-fuel-casks/refineries/ jet/missile/rocket-engines austenitic/FCC Ni/Fe-based (so MIS- called)``super"alloys(182/82;Hastelloy-X; 600;304/304L-SSs; 690 !!!) GENERIC ENDEMIC EXTANT detrimental(synonyms): Wigner's- diseas(WD)[J.Appl.Phys.17,857(46)]; Ostwald-ripening; spinodal- decomposition; overageing-embrittlement; thermomechanical- INstability: Mayo[Google: ``If Leaks Could Kill"; at flickr.com search on ``Giant-Magnotoresistance"; find: [Siegel<<<``Fert"(88) 2007-Nobel/Wolf/Japan-prizes]necessitating NRC inspections on 40+25=65 Westin``KL"ouse PWRs(12/06)]; Lai[Met.Trans.AIME,9A,827 (78)]-Sabol-Stickler[PSS(70)]; Ashpahani[Intl.Conf. H in Metals (77)]; Russell[Prog. Mtls.Sci.(83)]; Pollard[last UCS rept. (9/95)]; Lofaro[BNL/DOE/NRC Repts.]; Pringle[Nuclear-Power:From Physics to Politics(79)]; Hoffman[animatedsoftware.com],...what DOE/NRC MISlabels as ``butt-welds" ``stress-corrosion cracking" endpoint's ROOT-CAUSE ULTIMATE-ORIGIN is WD overageing-embrit- tlement caused brittle-fracture cracking from early/ongoing AEC/DOE-n``u''tional-la``v''atories sabotage!!!

FRAUD/SABOTAGE Killing Nuclear-Reactors Need Modeling!!!: "Super"alloys GENERIC ENDEMIC Wigner's-Disease/.../IN-stability: Ethics? SHMETHICS!!!

NASA Astrophysics Data System (ADS)

Asphahani, Aziz; Siegel, Sidney; Siegel, Edward

2010-03-01

Carbides solid-state chemistry domination of old/new nuclear- reactors/spent-fuel-casks/refineries/jet/missile/rocket-engines in austenitic/FCC Ni/Fe-based(so miscalled)``super"alloys(182/82; Hastelloy-X,600,304/304L-SSs,...,690!!!) GENERIC ENDEMIC EXTANT detrimental(synonyms): Wigner's-diseas(WD)[J.Appl.Phys.17,857 (1946)]/Ostwald-ripening/spinodal-decomposition/overageing- embrittlement/thermal-leading-to-mechanical(TLTM)-INstability: Mayo[Google:``If Leaks Could Kill"; at flickr.com search on ``Giant-Magnotoresistance"; find: Siegel[J.Mag.Mag.Mtls.7,312 (1978)]<<<``Fert"-"Gruenberg"(1988/89)2007-physics Nobel/Wolf/ Japan-prizes]necessitating NRC-inspections of 40+25 = 65 Westin- ``KLouse PWRs(12/2006)]-Lai[Met.Trans.AIME,9A,827(1978)]-Sabol- Stickler[Phys.Stat.Sol.(1970)]-Ashpahani[Intl.Conf. H in Metals, Paris(1977]-Russell[Prog.Mtls.Sci.(1983)]-Pollard[last UCS rept. (9/1995)]-Lofaro[BNL/DOE/NRC Repts.]-Pringle[Nuclear-Power:From Physics to Politics(1979)]-Hoffman[animatedsoftware.com], what DOE/NRC MISlabels as ``butt-welds" ``stress-corrosion cracking" endpoint's ROOT-CAUSE ULTIMATE-ORIGIN is WD overageing-embritt- lement caused brittle-fracture cracking from early/ongoing AEC/ DOE-n"u"tional-la"v"atories sabotage!!!

FRAUD/SABOTAGE Killing Nuclear-Reactors Need Modeling!!!: ``Super'' alloys GENERIC ENDEMIC Wigner's-Disease/.../IN-stability: Ethics? SHMETHICS!!!

NASA Astrophysics Data System (ADS)

O'Grady, Joseph; Bument, Arlden; Siegel, Edward

2011-03-01

Carbides solid-state chemistry domination of old/new nuclear-reactors/spent-fuel-casks/refineries/jet/missile/rocket-engines is austenitic/FCC Ni/Fe-based (so miscalled)"super"alloys(182/82;Hastelloy-X,600,304/304L-SSs,...690!!!) GENERIC ENDEMIC EXTANT detrimental(synonyms): Wigner's-disease(WD) [J.Appl.Phys.17,857 (46)]/Ostwald-ripening/spinodal-decomposition/overageing-embrittlement/thermal-leading-to-mechanical(TLTM)-INstability: Mayo[Google: fLeaksCouldKill > ; - Siegel [ J . Mag . Mag . Mtls . 7 , 312 (78) = atflickr . comsearchonGiant - Magnotoresistance [Fert" [PRL(1988)]-"Gruenberg"[PRL(1989)] 2007-Nobel]necessitating NRC inspections on 40+25=65 Westin"KL"ouse PWRs(12/2006)]-Lai [Met.Trans.AIME, 9A,827(78)]-Sabol-Stickler[Phys.Stat.Sol.(70)]-Ashpahani[ Intl.Conf. Hydrogen in Metals, Paris(1977]-Russell [Prog.Mtls.Sci.(1983)]-Pollard [last UCS rept.(9/1995)]-Lofaro [BNL/DOE/NRC Repts.]-Pringle [ Nuclear-Power:From Physics to Politics(1979)]-Hoffman [animatedsoftware.com], what DOE/NRC MISlabels as "butt-welds" "stress-corrosion cracking" endpoint's ROOT-CAUSE ULTIMATE-ORIGIN is WD overageing-embrittlement caused brittle-fracture cracking from early/ongoing AEC/DOE-n"u"tional-la"v"atories sabotage!!!

Impact of different thickness of the smooth heated surface on flow boiling heat transfer

NASA Astrophysics Data System (ADS)

Strąk, Kinga; Piasecka, Magdalena

2018-06-01

This paper presents a comparison of the performance of three smooth heated surfaces with different thicknesses. Analysis was carried out on an experimental setup for flow boiling heat transfer. The most important element of the setup was the test section with a rectangular minichannel, 1.7 mm deep, 16 mm wide and 180 mm long, oriented vertically. The heated element for the FC-72 Fluorinert flowing in the minichannel was designated as a Haynes-230 alloy plate (0.10 mm and 0.45 mm thick) or a Hastelloy X alloy plate (0.65 mm thick). Infrared thermography was used to measure the temperature of the outer plate surface. The local values of the heat transfer coefficient for stationary state conditions were calculated using a simple one-dimensional method. The experimental results were presented as the relationship between the heat transfer coefficients in the subcooled boiling region and the distance along the minichannel length and boiling curves. The highest local heat transfer coefficients were recorded for the surface of 0.10 mm thick heated plate at the outlet and 0.45 mm thick plate at the minichannel inlet. All boiling curves were typical in shape.

Creep Property Characterization of Potential Brayton Cycle Impeller and Duct Materials

NASA Astrophysics Data System (ADS)

Gabb, Timothy P.; Gayda, John; Garg, Anita

2007-01-01

Cast superalloys have potential applications in space as impellers within closed-loop Brayton cycle nuclear power generation systems. Likewise wrought superalloys are good candidates for ducts and heat exchangers transporting the inert working gas in a Brayton-based power plant. Two cast superalloys, Mar-M247LC and IN792, and a NASA GRC powder metallurgy superalloy, LSHR, have been screened to compare their respective capabilities for impeller applications. Mar-M247LC has been selected for additional long term evaluations. Initial tests in helium indicate this inert environment may debit long term creep resistance of this alloy. Several wrought superalloys including Hastelloy® X, Inconel® 617, Inconel® 740, Nimonic® 263, Incoloy® MA956, and Haynes 230 are also being screened to compare their capabilities for duct applications. Haynes 230 has been selected for additional long term evaluations. Initial tests in helium are just underway for this alloy. These proposed applications would require sufficient strength and creep resistance for long term service at temperatures up to 1200 K, with service times to 100,000 h or more. Therefore, long term microstructural stability is also being screened.

Creep Property Characterization of Potential Brayton Cycle Impeller and Duct Materials

NASA Technical Reports Server (NTRS)

Gabb, Timothy P.; Gayda, john; Garg, Anita

2007-01-01

Cast superalloys have potential applications in space as impellers within closed-loop Brayton cycle nuclear power generation systems. Likewise wrought superalloys are good candidates for ducts and heat exchangers transporting the inert working gas in a Brayton-based power plant. Two cast superalloys, Mar-M247LC and IN792, and a NASA GRC powder metallurgy superalloy, LSHR, have been screened to compare their respective capabilities for impeller applications. Mar-M247LC has been selected for additional long term evaluations. Initial tests in helium indicate this inert environment may debit long term creep resistance of this alloy. Several wrought superalloys including Hastelloy(Registered TradeMark) X, Inconel(Registered TradeMark) 617, Inconel(Registered TradeMark) 740, Nimonic(Registered TradeMark) 263, Incoloy(Registered TradeMark) MA956, and Haynes 230 are also being screened to compare their capabilities for duct applications. Haynes 230 has been selected for additional long term evaluations. Initial tests in helium are just underway for this alloy. These proposed applications would require sufficient strength and creep resistance for long term service at temperatures up to 1200 K, with service times to 100,000 h or more. Therefore, long term microstructural stability is also being screened.

Comparative effectiveness of extended-release naltrexone versus buprenorphine-naloxone for opioid relapse prevention (X:BOT): a multicentre, open-label, randomised controlled trial

PubMed Central

Lee, Joshua D; Nunes, Edward V; Novo, Patricia; Bachrach, Ken; Bailey, Genie L; Bhatt, Snehal; Farkas, Sarah; Fishman, Marc; Gauthier, Phoebe; Hodgkins, Candace C; King, Jacquie; Lindblad, Robert; Liu, David; Matthews, Abigail G; May, Jeanine; Peavy, K Michelle; Ross, Stephen; Salazar, Dagmar; Schkolnik, Paul; Shmueli-Blumberg, Dikla; Stablein, Don; Subramaniam, Geetha; Rotrosen, John

2018-01-01

Summary Background Extended-release naltrexone (XR-NTX), an opioid antagonist, and sublingual buprenorphine-naloxone (BUP-NX), a partial opioid agonist, are pharmacologically and conceptually distinct interventions to prevent opioid relapse. We aimed to estimate the difference in opioid relapse-free survival between XR-NTX and BUP-NX. Methods We initiated this 24 week, open-label, randomised controlled, comparative effectiveness trial at eight US community-based inpatient services and followed up participants as outpatients. Participants were 18 years or older, had Diagnostic and Statistical Manual of Mental Disorders-5 opioid use disorder, and had used non-prescribed opioids in the past 30 days. We stratified participants by treatment site and opioid use severity and used a web-based permuted block design with random equally weighted block sizes of four and six for randomisation (1:1) to receive XR-NTX or BUP-NX. XR-NTX was monthly intramuscular injections (Vivitrol; Alkermes) and BUP-NX was daily self-administered buprenorphine-naloxone sublingual film (Suboxone; Indivior). The primary outcome was opioid relapse-free survival during 24 weeks of outpatient treatment. Relapse was 4 consecutive weeks of any non-study opioid use by urine toxicology or self-report, or 7 consecutive days of self-reported use. This trial is registered with ClinicalTrials.gov, NCT02032433. Findings Between Jan 30, 2014, and May 25, 2016, we randomly assigned 570 participants to receive XR-NTX (n=283) or BUP-NX (n=287). The last follow-up visit was Jan 31, 2017. As expected, XR-NTX had a substantial induction hurdle: fewer participants successfully initiated XR-NTX (204 [72%] of 283) than BUP-NX (270 [94%] of 287; p<0·0001). Among all participants who were randomly assigned (intention-to-treat population, n=570) 24 week relapse events were greater for XR-NTX (185 [65%] of 283) than for BUP-NX (163 [57%] of 287; hazard ratio [HR] 1·36, 95% CI 1·10–1·68), most or all of this difference accounted for by early relapse in nearly all (70 [89%] of 79) XR-NTX induction failures. Among participants successfully inducted (per-protocol population, n=474), 24 week relapse events were similar across study groups (p=0·44). Opioid-negative urine samples (p<0·0001) and opioid-abstinent days (p<0·0001) favoured BUP-NX compared with XR-NTX among the intention-to-treat population, but were similar across study groups among the per-protocol population. Self-reported opioid craving was initially less with XR-NTX than with BUP-NX (p=0·0012), then converged by week 24 (p=0·20). With the exception of mild-to-moderate XR-NTX injection site reactions, treatment-emergent adverse events including overdose did not differ between treatment groups. Five fatal overdoses occurred (two in the XR-NTX group and three in the BUP-NX group). Interpretation In this population it is more difficult to initiate patients to XR-NTX than BUP-NX, and this negatively affected overall relapse. However, once initiated, both medications were equally safe and effective. Future work should focus on facilitating induction to XR-NTX and on improving treatment retention for both medications. PMID:29150198

Fed and Fasted Single-dose Assessment of Bioequivalence of Dapagliflozin and Metformin Extended-release Fixed-dose Combination Tablets Relative to Single-component Dapagliflozin and Metformin Extended-release Tablets in Healthy Subjects.

PubMed

Boulton, David W; Chang, Ming; Griffen, Steven C; Kitaura, Catia; Lubin, Susan; Pollack, Allyson; LaCreta, Frank

2016-01-01

In patients with type 2 diabetes mellitus, fixed-dose combinations (FDCs) of antihyperglycemic medications may provide complementary efficacy while reducing tablet burden and improving compliance. The aim of this study was to assess the bioequivalence and tolerability of 2 FDCs of dapagliflozin and metformin extended-release (XR) versus their individual component (IC) tablets. An open-label, balanced, randomized, 2-way crossover, 4-arm study was conducted in 129 healthy Brazilian subjects (aged 18-55 years). Two oral doses of the FDCs (5 mg dapagliflozin and 500 mg metformin XR, and 10 mg dapagliflozin and 1000 mg metformin XR) were evaluated in fed and fasted states. Under fed and fasted conditions the 5 mg dapagliflozin and 500 mg metformin XR FDC showed bioequivalence to its ICs. The 10 mg dapagliflozin and 1000 mg metformin XR FDC was bioequivalent to its ICs in fed subjects. Although AUC for the 10 mg dapagliflozin and 1000 mg metformin XR FDC was bioequivalent in fasted subjects, the Cmax for metformin was not bioequivalent to its ICs in fasted subjects (upper 90% CI was 127.5%, and thus outside the 80%-125% bioequivalence interval). The small increase in the fasted state is not considered clinically meaningful due to the small magnitude of the difference (9.2%), the lack of metformin Cmax being associated with efficacy or tolerability concerns, and the fasted state not being the recommended state for dosing of metformin XR. The safety profile and tolerability of the FDCs were similar to those of their ICs and no deaths or serious adverse events were reported. Both FDCs of dapagliflozin and metformin XR were bioequivalent to their ICs in fed and fasted subjects, except for the metformin Cmax from the 10 mg dapagliflozin and 1000 mg metformin XR FDC in fasted subjects. These data support the use of a dapagliflozin and metformin XR FDC in patients with type 2 diabetes mellitus. Copyright © 2016 Elsevier HS Journals, Inc. All rights reserved.

Effects of injectable extended-release naltrexone (XR-NTX) for opioid dependence on residential rehabilitation outcomes and early follow-up.

PubMed

Leslie, Douglas L; Milchak, William; Gastfriend, David R; Herschman, Philip L; Bixler, Edward O; Velott, Diana L; Meyer, Roger E

2015-04-01

Little is known about the use of extended-release naltrexone (XR-NTX) during residential rehabilitation, and its effects on early outcomes and rates of follow-up treatment. This study examined patient characteristics and rates of treatment completion and engagement in post-residential care of opioid dependent patients who received XR-NTX during residential rehabilitation, compared with patients who did not receive this medication. Electronic records for opioid dependent patients from three Pennsylvania residential detoxification and treatment facilities (N = 7,687) were retrospectively analyzed. We determined the proportion of patients who received XR-NTX (INJ), and compared rates of treatment completion and engagement in follow-up care relative to a naturalistic control group of patients recommended for, but not administered, XR-NTX (Non-INJ). Data on whether the patient initiated follow-up care were available from one site (N = 3,724). Overall, 598 (7.8%) patients were recommended for XR-NTX and of these, 168 (28.1%) received injections. Compared to non-INJ patients, INJ patients were less likely to leave against medical advice (4.8% vs. 30.2%, p < .001) and more likely to initiate follow-up care (37.7% vs. 19.7%, p < .001). These differences remained significant after controlling for demographic covariates using regression analysis. XR-NTX was associated with higher rates of residential and early post-residential care engagement in patients with opioid dependence. XR-NTX may be an effective adjunct in the residential treatment and aftercare of patients with opioid dependence. © American Academy of Addiction Psychiatry.

Spatial distribution and ecological risk assessment of phthalic acid esters and phenols in surface sediment from urban rivers in Northeast China.

PubMed

Li, Bin; Liu, Ruixia; Gao, Hongjie; Tan, Ruijie; Zeng, Ping; Song, Yonghui

2016-12-01

Concentration and spatial distribution of six phthalic acid esters (PAEs) and eight phenols in sediments of urban rivers, namely the Xi River (XR) and Pu River (PR) in Shenyang city, Northeast China were investigated and the ecological risk of these target pollutants was assessed based on the risk quotient (RQ) approach. Target PAEs and phenols were detected in most of sediment samples collected from the XR and PR. The concentrations of total PAEs in sediments varied from 22.4 to 369 μg/g dw in the XR and 3.71-46.9 μg/g dw in the PR. The levels of phenols ranged from 2.72 to 106 μg/g dw in the XR and 0.811-25.0 μg/g dw in the PR, respectively. The dominant pollutants in both XR and PR were DEHP, phenol and 4-methylphnol. The sampling locations XR1-3 in the XR suffered severe contamination from PAEs and phenols. The sites PR1 and PR6 were heavily polluted by phenols and PAEs, respectively. Almost all target PAEs and phenolic compounds in sediment of the XR exhibited medium or high ecological risk to organisms and the ecological risk in the PR mainly originated from PEAs, phenol and 4-methylphenol. These results would provide guidance for individual pollutant control and indicate that it is imperative to take some effective measures to reduce the pollution of those contaminants. Copyright © 2016 Elsevier Ltd. All rights reserved.

Saccharomyces cerevisiae engineered for xylose metabolism requires gluconeogenesis and the oxidative branch of the pentose phosphate pathway for aerobic xylose assimilation

USDA-ARS?s Scientific Manuscript database

Saccharomyces strains engineered to ferment xylose using Scheffersomyces stipitis xylose reductase (XR) and xylitol dehydrogenase (XDH) genes appear to be limited by metabolic imbalances due to differing cofactor specificities of XR and XDH. The S. stipitis XR, which uses nicotinamide adenine dinucl...

Intercalation of XR5944 with the estrogen response element is modulated by the tri-nucleotide spacer sequence between half-sites

PubMed Central

Sidell, Neil; Mathad, Raveendra I.; Shu, Feng-jue; Zhang, Zhenjiang; Kallen, Caleb B.; Yang, Danzhou

2011-01-01

DNA-intercalating molecules can impair DNA replication, DNA repair, and gene transcription. We previously demonstrated that XR5944, a DNA bis-intercalator, specifically blocks binding of estrogen receptor-α (ERα) to the consensus estrogen response element (ERE). The consensus ERE sequence is AGGTCAnnnTGACCT, where nnn is known as the tri-nucleotide spacer. Recent work has shown that the tri-nucleotide spacer can modulate ERα-ERE binding affinity and ligand-mediated transcriptional responses. To further understand the mechanism by which XR5944 inhibits ERα-ERE binding, we tested its ability to interact with consensus EREs with variable tri-nucleotide spacer sequences and with natural but non-consensus ERE sequences using one dimensional nuclear magnetic resonance (1D 1H NMR) titration studies. We found that the tri-nucleotide spacer sequence significantly modulates the binding of XR5944 to EREs. Of the sequences that were tested, EREs with CGG and AGG spacers showed the best binding specificity with XR5944, while those spaced with TTT demonstrated the least specific binding. The binding stoichiometry of XR5944 with EREs was 2:1, which can explain why the spacer influences the drug-DNA interaction; each XR5944 spans four nucleotides (including portions of the spacer) when intercalating with DNA. To validate our NMR results, we conducted functional studies using reporter constructs containing consensus EREs with tri-nucleotide spacers CGG, CTG, and TTT. Results of reporter assays in MCF-7 cells indicated that XR5944 was significantly more potent in inhibiting the activity of CGG- than TTT-spaced EREs, consistent with our NMR results. Taken together, these findings predict that the anti-estrogenic effects of XR5944 will depend not only on ERE half-site composition but also on the tri-nucleotide spacer sequence of EREs located in the promoters of estrogen-responsive genes. PMID:21333738

A Randomized, Placebo-Controlled Pilot Study of Quetiapine-XR Monotherapy or Adjunctive Therapy to Antidepressant in Acute Major Depressive Disorder with Current Generalized Anxiety Disorder

PubMed Central

Li, Ranran; Wu, Renrong; Chen, Jun; Kemp, David E.; Ren, Ming; Conroy, Carla; Chan, Philip; Serrano, Mary Beth; Ganocy, Stephen J.; Calabrese, Joseph R.; Gao, Keming

2016-01-01

Objectives To pilot efficacy and safety data of quetiapine-XR monotherapy or adjunctive therapy to antidepressant(s) in the acute treatment of MDD with current generalized anxiety disorder (GAD). Methods The Mini International Neuropsychiatric Interview was used to ascertain the diagnosis of DSM-IV Axis I disorders. Eligible patients were randomly assigned to quetiapine-XR or placebo for up to 8 weeks. Changes from baseline to endpoint in Hamilton Depression Rating Scale-17 items (HAMD-17), Hamilton Anxiety Rating Scale (HAM-A), Clinical Global Impression-Severity (CGI-S), Quick Inventory of Depression Symptomatology-16 items Self-Report (QIDS-16-SR) total scores, and other outcome measures were analyzed with the last observation carried forward strategy and/or mixed-effects modeling for repeated measures. Results Of the 34 patients screened, 23 patients were randomized to receive quetiapine-XR (n = 11) or placebo (n = 12), with 5 and 4 completing the study, respectively. The mean dose of quetiapine-XR was 154 ± 91 mg/d. The change from baseline to endpoint in the total scores of HAMD-17, HAM-A, QIDS-16-SR, and CGI-S were significant in the quetiapine-XR group, but only the change in HAM-A total score was significant in the placebo group. The differences in these changes between the two groups were only significant in CGI-S scores, with the rest of numerical larger in the quetiapine-XR group. The most common side effects from quetiapine-XR were dry mouth, somnolence/sedation, and fatigue. Conclusions In this pilot study, quetiapine-XR was numerically superior to placebo in reducing depressive and anxiety symptoms in patients with MDD and current GAD. Large sample studies are warranted to support or refute these preliminary findings. PMID:27738370

Creep-rupture tests of internally pressurized Hastelloy-X tubes

NASA Technical Reports Server (NTRS)

Gumto, K. H.; Colantino, G. J.

1973-01-01

Seamless Hastelloy-X tubes with 0.375-in. outside diameter and 0.025-in. wall thickness were tested to failure at temperatures from 1400 to 1650 F and internal helium pressures from 800 to 1800 psi. Lifetimes ranged from 58 to 3600 hr. The creep-rupture strength of the tubes was from 20 to 40 percent lower than that of sheet specimens. Larson-Miller correlations and photomicrographs of some specimens are presented.

The anti-corrosion behavior under multi-factor impingement of Hastelloy C22 coating prepared by multilayer laser cladding

NASA Astrophysics Data System (ADS)

Chen, Lin; Bai, Shu-Lin

2018-04-01

Hastelloy C22 coating was prepared on substrate of Q235 steel by high power multilayer laser cladding. The microstructure, hardness and anti-corrosion properties of coating were investigated. The corrosion tests in 3.5% NaCl solution were carried out with variation of impingement angle and velocity, and vibration frequency of sample. The microstructure of coating changes from equiaxed grain at the top surface to dendrites oriented at an angle of 60° to the substrate inside the coating. The corrosion rate of coating increases with the increase of impingement angle and velocity, and vibrant frequency of sample. Corrosion mechanisms relate to repassivation and depassivation of coating according to electrochemical measurements. Above results show that multilayer laser cladding can endow Hastelloy C22 coating with fine microstructures, high hardness and good anti-corrosion performances.

Extended release naltrexone injection is performed in the majority of opioid dependent patients receiving outpatient induction: a very low dose naltrexone and buprenorphine open label trial.

PubMed

Mannelli, Paolo; Wu, Li-Tzy; Peindl, Kathleen S; Swartz, Marvin S; Woody, George E

2014-05-01

The approval of extended release injectable naltrexone (XR-NTX; Vivitrol(®)) has introduced a new option for treating opioid addiction, but studies are needed to identify its place within the spectrum of available therapies. The absence of physiological opioid dependence is a necessary and challenging first step for starting XR-NTX. Outpatient detoxification gives poor results and inpatient detoxification is either unavailable or too brief for the physiological effects of opioids to resolve. Here we present findings from an open label study that tested whether the transition from opioid addiction to XR-NTX can be safely and effectively performed in an outpatient setting using very low dose naltrexone and buprenorphine. Twenty treatment seeking opioid addicted individuals were given increasing doses of naltrexone starting at 0.25mg with decreasing doses of buprenorphine starting at 4 mg during a 7-day outpatient XR-NTX induction procedure. Withdrawal discomfort, craving, drug use, and adverse events were assessed daily until the XR-NTX injection, then weekly over the next month. Fourteen of the 20 participants received XR-NTX and 13 completed weekly assessments. Withdrawal, craving, and opioid or other drug use were significantly lower during induction and after XR-NTX administration compared with baseline, and no serious adverse events were recorded. Outpatient transition to XR-NTX combining upward titration of very low dose naltrexone with downward titration of low dose buprenorphine was safe, well tolerated, and completed by most participants. Further studies with larger numbers of subjects are needed to see if this approach is useful for naltrexone induction. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Long-Acting Injectable Naltrexone Induction: A Randomized Trial of Outpatient Opioid Detoxification With Naltrexone Versus Buprenorphine.

PubMed

Sullivan, Maria; Bisaga, Adam; Pavlicova, Martina; Choi, C Jean; Mishlen, Kaitlyn; Carpenter, Kenneth M; Levin, Frances R; Dakwar, Elias; Mariani, John J; Nunes, Edward V

2017-05-01

At present there is no established optimal approach for transitioning opioid-dependent adults to extended-release injection naltrexone (XR-naltrexone) while preventing relapse. The authors conducted a trial examining the efficacy of two methods of outpatient opioid detoxification for induction to XR-naltrexone. Participants were 150 opioid-dependent adults randomly assigned 2:1 to one of two outpatient detoxification regimens, naltrexone-assisted detoxification or buprenorphine-assisted detoxification, followed by an injection of XR-naltrexone. Naltrexone-assisted detoxification lasted 7 days and included a single day of buprenorphine followed by ascending doses of oral naltrexone along with clonidine and other adjunctive medications. Buprenorphine-assisted detoxification included a 7-day buprenorphine taper followed by a week-long delay before administration of XR-naltrexone, consistent with official prescribing information for XR-naltrexone. Participants from both groups received behavioral therapy focused on medication adherence and a second dose of XR-naltrexone. Compared with participants in the buprenorphine-assisted detoxification condition, participants assigned to naltrexone-assisted detoxification were significantly more likely to be successfully inducted to XR-naltrexone (56.1% compared with 32.7%) and to receive the second injection at week 5 (50.0% compared with 26.9%). Both models adjusted for primary type of opioid use, route of opioid administration, and morphine equivalents at baseline. These results demonstrate the safety, efficacy, and tolerability of low-dose naltrexone, in conjunction with single-day buprenorphine dosing and adjunctive nonopioid medications, for initiating adults with opioid dependence to XR-naltrexone. This strategy offers a promising alternative to the high rates of attrition and relapse currently observed with agonist tapers in both inpatient and outpatient settings.

Opioid use and dropout in patients receiving oral naltrexone with or without single administration of injection naltrexone.

PubMed

Sullivan, Maria A; Bisaga, Adam; Glass, Andrew; Mishlen, Kaitlyn; Pavlicova, Martina; Carpenter, Kenneth M; Mariani, John J; Levin, Frances R; Nunes, Edward V

2015-02-01

Adherence to oral naltrexone has been poor and can be improved somewhat with behavioral therapy. We compared behavioral naltrexone therapy (BNT) to compliance enhancement (CE) and tested efficacy of single-dose injection naltrexone (XR-NTX; 384 mg) with behavioral therapies at further improving adherence to oral naltrexone. A 24-week, randomized, placebo-controlled trial (n=125) compared four treatment conditions following inpatient detoxification and oral naltrexone induction: (1) BNT+XR-NTX; (2) BNT+placebo injection; (3) CE+XR-NTX; and (4) CE+placebo injection. All participants were maintained on oral naltrexone throughout the trial. Primary outcome was retention in treatment. Of 89 randomized participants, 78.7% (70/89) completed 4 weeks, 58.2% (54/89) completed 8 weeks, 47.2% (42/89) completed 12 weeks, and 25.8% (23/89) completed 24 weeks. A Cox proportional hazards regression modeled time to dropout as a function of treatment condition, baseline opioid dependence severity (bags per day of heroin use), and their interaction. Interaction of conditions by baseline severity was significant (X3(2)=9.19, p=0.027). For low-severity patients (≤ 6 bags/day), retention was highest in the BNT-XR-NTX group (60% at 6 months), as hypothesized. For high-severity (>6 bags/day) patients, BNT-XR-NTX did not perform as well, due to high early attrition. For low-severity heroin users, single-dose XR-NTX improved long-term treatment retention when combined with behavioral therapy. In higher-severity opioid-dependent patients, XR-NTX was less helpful, perhaps because, combined with oral naltrexone, it produced higher blood levels and more withdrawal discomfort. When cost considerations recommend oral naltrexone following XR-NTX, the latter should be phased in slowly. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Estimation of Eye Lens Dose During Brain Scans Using Gafchromic Xr-QA2 Film in Various Multidetector CT Scanners.

PubMed

Akhilesh, Philomina; Kulkarni, Arti R; Jamhale, Shramika H; Sharma, S D; Kumar, Rajesh; Datta, D

2017-04-25

The purpose of this study was to estimate eye lens dose during brain scans in 16-, 64-, 128- and 256-slice multidetector computed tomography (CT) scanners in helical acquisition mode and to test the feasibility of using radiochromic film as eye lens dosemeter during CT scanning. Eye lens dose measurements were performed using Gafchromic XR-QA2 film on a polystyrene head phantom designed with outer dimensions equivalent to the head size of a reference Indian man. The response accuracy of XR-QA2 film was validated by using thermoluminescence dosemeters. The eye lens dose measured using XR-QA2 film on head phantom for plain brain scanning in helical mode ranged from 43.8 to 45.8 mGy. The XR-QA2 film measured dose values were in agreement with TLD measured dose values within a maximum variation of 8.9%. The good correlation between the two data sets confirms the viability of using XR-QA2 film for eye lens dosimetry. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Apical P2XR contribute to [Ca2+]i signaling and Isc in mouse renal MCD.

PubMed

Li, Liuzhe; Lynch, I Jeanette; Zheng, Wencui; Cash, Melanie N; Teng, Xueling; Wingo, Charles S; Verlander, Jill W; Xia, Shen-Ling

2007-08-03

We examined P2X receptor expression and distribution in the mouse collecting duct (CD) and their functional role in Ca(2+) signaling. Both P2X(1) and P2X(4) were detected by RT-PCR and Western blot. Immunohistochemistry demonstrated apical P2X(1) and P2X(4) immunoreactivity in principal cells in the outer medullary CD (OMCD) and inner medullary CD (IMCD). Luminal ATP induced an increase in Ca(2+) signaling in native medullary CD (MCD) as measured by fluorescence imaging. ATP also induced an increase in Ca(2+) signaling in MCD cells grown in primary culture but not in the presence of P2XR antagonist PPNDS. Short circuit current (I(sc)) measurement with mouse IMCD cells showed that P2XR agonist BzATP induced a larger I(sc) than did P2YR agonist UTP in the apical membrane. Our data reveal for the first time that P2X(1) and P2X(4) are cell-specific with prominent immunoreactivity in the apical area of MCD cells. The finding that P2XR blockade inhibits ATP-induced Ca(2+) signaling suggests that activation of P2XR is a key step in Ca(2+)-dependent purinergic signaling. The result that activation of P2XR produces large I(sc) indicates the necessity of P2XR in renal CD ion transport.

Extended-release naltrexone opioid treatment at jail reentry (XOR)

PubMed Central

McDonald, Ryan D.; Tofighi, Babak; Laska, Eugene; Goldfeld, Keith; Bonilla, Wanda; Flannery, Mara; Santana-Correa, Nadina; Johnson, Christopher W.; Leibowitz, Neil; Rotrosen, John; Gourevitch, Marc N.; Lee, Joshua D.

2017-01-01

Background Extended-release naltrexone (XR-NTX) is an injectable monthly sustained-release mu opioid receptor antagonist, which blocks the typical effects of heroin and other opioid agonists. Use of XR-NTX among opioid dependent persons leaving jails and prisons is increasing despite scant high-quality evidence regarding XR-NTX’s effectiveness at re-entry. Methods This 24-week, open-label randomized controlled trial examines the effectiveness of XR-NTX as opioid relapse prevention at release from jail (N = 85) compared to enhanced treatment as usual (ETAU, N = 85). A third, non-randomized, quasi-experimental naturalistic arm of participants who have newly initiated a jail-to-community methadone treatment program (MTP, N = 85) allows for comparisons to a methadone standard-of-care. Results We describe the rationale, design, and primary and secondary outcomes of the study. The primary outcome is an opioid relapse event; the primary contrast is a time-to-relapse comparison of XR-NTX and ETAU over a 24-week treatment phase. Secondary outcomes are rates of: (a) post-release opioid treatment participation, (b) opioid, alcohol, and cocaine use, (c) injection drug use and HIV sexual risk behaviors, (d) overdose (fatal and non-fatal) and all-cause mortality, and, (e) re-incarceration. Conclusions XR-NTX is a potentially important, effective treatment and relapse prevention option for a large US population of persons with opioid use disorders leaving jails. This study will estimate XR-NTX’s effectiveness relative to existing standards of care, including counseling-only treatment-as-usual and methadone maintenance. PMID:27178765

Extended-release intramuscular naltrexone (VIVITROL®): a review of its use in the prevention of relapse to opioid dependence in detoxified patients.

PubMed

Syed, Yahiya Y; Keating, Gillian M

2013-10-01

Naltrexone is a μ-opioid receptor antagonist that blocks the euphoric effects of heroin and prescription opioids. In order to improve treatment adherence, a once-monthly, intramuscular, extended-release formulation of naltrexone (XR-NTX) [VIVITROL(®)] has been developed, and approved in the USA and Russia for the prevention of relapse to opioid dependence, after opioid detoxification. The clinical efficacy of this formulation in patients with opioid dependence was demonstrated in a 24-week, randomized, double-blind, placebo-controlled, multicentre, phase III trial (ALK21-013; n = 250). In this trial, opioid-detoxified patients receiving XR-NTX 380 mg once every 4 weeks, in combination with psychosocial support, had a significantly higher median proportion of weeks of confirmed opioid abstinence during weeks 5-24, compared with those receiving placebo (primary endpoint). A significantly higher proportion of patients receiving XR-NTX achieved total confirmed abstinence during this period than those receiving placebo. XR-NTX was also associated with a significantly greater reduction in opioid craving and a significantly longer treatment retention period than placebo. XR-NTX was generally well tolerated in the phase III trial. The most common (incidence ≥5 %) treatment-emergent adverse events that also occurred more frequently with XR-NTX than with placebo were hepatic enzyme abnormalities, nasopharyngitis, insomnia, hypertension, influenza and injection-site pain. Thus, XR-NTX is a useful treatment option for the prevention of relapse to opioid dependence, following opioid detoxification.

Tissue Distribution and Whole Body Burden of the Chlorinated Polyfluoroalkyl Ether Sulfonic Acid F-53B in Crucian Carp (Carassius carassius): Evidence for a Highly Bioaccumulative Contaminant of Emerging Concern.

PubMed

Shi, Yali; Vestergren, Robin; Zhou, Zhen; Song, Xiaowei; Xu, Lin; Liang, Yong; Cai, Yaqi

2015-12-15

Following the global actions to phase out perfluoroctanesulfonic acid (PFOS) a large number of alternative per- and polyfluoroalkyl substances, with poorly defined hazard properties, are being used in increasing quantities. Here, we report on the first detection of the chlorinated polyfluoroalkyl ether sulfonic acid F-53B in biological samples and determine the tissue distribution and whole body bioaccumulation factors (BAFwhole body) in crucian carp (Carassius carassius). Analysis of fish samples from Xiaoqing River (XR) and Tangxun Lake (TL) demonstrated a similar level of F-53B contamination with median concentrations in blood of 41.9 and 20.9 ng/g, respectively. Tissue/blood ratios showed that distribution of F-53B primarily occurs to the kidney (TL: 0.48, XR: 0.54), gonad (TL: 0.36, XR: 0.54), liver (TL: 0.38, XR: 0.53), and heart (TL: 0.47, XR: 0.47). Median Log BAFwhole body values for F-53B (XR: 4.124, TL: 4.322) exceeded regulatory bioaccumulation criterion and were significantly higher than those of PFOS in the same data sets (XR: 3.430, TL: 3.279). On the basis of its apparent omnipresence and strong bioaccumulation propensity, it is hypothesized that F-53B could explain a significant fraction of previously unidentified organofluorine in biological samples from China, and regulatory actions for this compound are encouraged.

Comparative analysis of upper gastrointestinal endoscopy, double-contrast upper gastrointestinal barium X-ray radiography, and the titer of serum anti-Helicobacter pylori IgG focusing on the diagnosis of atrophic gastritis.

PubMed

Yamamichi, Nobutake; Hirano, Chigaya; Takahashi, Yu; Minatsuki, Chihiro; Nakayama, Chiemi; Matsuda, Rie; Shimamoto, Takeshi; Takeuchi, Chihiro; Kodashima, Shinya; Ono, Satoshi; Tsuji, Yosuke; Fujishiro, Mitsuhiro; Wada, Ryoichi; Mitsushima, Toru; Koike, Kazuhiko

2016-04-01

Upper gastrointestinal endoscopy (UGI-ES) and double-contrast upper gastrointestinal barium X-ray radiography (UGI-XR) are two major image-based methods to diagnose atrophic gastritis, which is mostly induced by Helicobacter pylori infection. However, there have been few studies directly comparing them. Atrophic gastritis was evaluated using the data of 962 healthy subjects who underwent UGI-ES and UGI-XR within 1 year. Based on UGI-ES and UGI-XR, 602 subjects did not have atrophic gastritis and 254 subjects did have it. Considering UGI-ES-based atrophic gastritis as the standard, sensitivity and specificity of UGI-XR-based atrophic gastritis were 92.0 % (254/276) and 92.8 % (602/649), respectively. The seven-grade Kimura-Takemoto classification of UGI-ES-based atrophic gastritis showed a strong and significant association with the four-grade UGI-XR-based atrophic gastritis. Sensitivity and specificity of serum anti-Helicobacter pylori IgG to detect UGI-ES/UGI-XR-based atrophic gastritis were 89.4 % (227/254) and 99.8 % (601/602), indicating that atrophic gastritis can be overlooked according to serum anti-Helicobacter pylori IgG alone.

Construction of plasmid-free Escherichia coli for the production of arabitol-free xylitol from corncob hemicellulosic hydrolysate.

PubMed

Su, Buli; Zhang, Zhe; Wu, Mianbin; Lin, Jianping; Yang, Lirong

2016-05-26

High costs and low production efficiency are a serious constraint to bio-based xylitol production. For industrial-scale production of xylitol, a plasmid-free Escherichia coli for arabitol-free xylitol production from corncob hemicellulosic hydrolysate has been constructed. Instead of being plasmid and inducer dependent, this strain relied on multiple-copy integration of xylose reductase (XR) genes into the chromosome, where their expression was controlled by the constitutive promoter P43. In addition, to minimize the flux from L-arabinose to arabitol, two strategies including low XR total activity and high selectivity of XR has been adopted. Arabitol was significantly decreased using plasmid-free strain which had lower XR total activity and an eight point-mutations of XR with a 27-fold lower enzyme activity toward L-arabinose was achieved. The plasmid-free strain in conjunction with this mutant XR can completely eliminate arabitol formation in xylitol production. In fed-batch fermentation, this plasmid-free strain produced 143.8 g L(-1) xylitol at 1.84 g L(-1) h(-1) from corncob hemicellulosic hydrolysate. From these results, we conclude that this route by plasmid-free E. coli has potential to become a commercially viable process for xylitol production.

Construction of plasmid-free Escherichia coli for the production of arabitol-free xylitol from corncob hemicellulosic hydrolysate

PubMed Central

Su, Buli; Zhang, Zhe; Wu, Mianbin; Lin, Jianping; Yang, Lirong

2016-01-01

High costs and low production efficiency are a serious constraint to bio-based xylitol production. For industrial-scale production of xylitol, a plasmid-free Escherichia coli for arabitol-free xylitol production from corncob hemicellulosic hydrolysate has been constructed. Instead of being plasmid and inducer dependent, this strain relied on multiple-copy integration of xylose reductase (XR) genes into the chromosome, where their expression was controlled by the constitutive promoter P43. In addition, to minimize the flux from L-arabinose to arabitol, two strategies including low XR total activity and high selectivity of XR has been adopted. Arabitol was significantly decreased using plasmid-free strain which had lower XR total activity and an eight point-mutations of XR with a 27-fold lower enzyme activity toward L-arabinose was achieved. The plasmid-free strain in conjunction with this mutant XR can completely eliminate arabitol formation in xylitol production. In fed-batch fermentation, this plasmid-free strain produced 143.8 g L−1 xylitol at 1.84 g L−1 h−1 from corncob hemicellulosic hydrolysate. From these results, we conclude that this route by plasmid-free E. coli has potential to become a commercially viable process for xylitol production. PMID:27225023

Extended‐Release Once‐Daily Formulation of Tofacitinib: Evaluation of Pharmacokinetics Compared With Immediate‐Release Tofacitinib and Impact of Food

PubMed Central

Wang, Rong; Fletcher, Tracey; Alvey, Christine; Kushner, Joseph; Stock, Thomas C.

2016-01-01

Abstract Tofacitinib is an oral Janus kinase inhibitor for the treatment of rheumatoid arthritis. An extended‐release (XR) formulation has been designed to provide a once‐daily (QD) dosing option to patients to achieve comparable pharmacokinetic (PK) parameters to the twice‐daily immediate‐release (IR) formulation. We conducted 2 randomized, open‐label, phase 1 studies in healthy volunteers. Study A characterized single‐dose and steady‐state PK of tofacitinib XR 11 mg QD and intended to demonstrate equivalence of exposure under single‐dose and steady‐state conditions to tofacitinib IR 5 mg twice daily. Study B assessed the effect of a high‐fat meal on the bioavailability of tofacitinib from the XR formulation. Safety and tolerability were monitored in both studies. In study A (N = 24), the XR and IR formulations achieved time to maximum plasma concentration at 4 hours and 0.5 hours postdose, respectively; terminal half‐life was 5.9 hours and 3.2 hours, respectively. Area under plasma concentration‐time curve (AUC) and maximum plasma concentration (Cmax) after single‐ and multiple‐dose administration were equivalent between the XR and IR formulations. In study B (N = 24), no difference in AUC was observed for fed vs fasted conditions. Cmax increased by 27% under the fed state. On repeat administration, negligible accumulation (<20%) of systemic exposures was observed for both formulations. Steady state was achieved within 48 hours of dosing with the XR formulation. Tofacitinib administration as an XR or IR formulation was generally well tolerated in these studies. PMID:26970526

Ethanol production from xylose by recombinant Saccharomyces cerevisiae expressing protein-engineered NADH-preferring xylose reductase from Pichia stipitis.

PubMed

Watanabe, Seiya; Abu Saleh, Ahmed; Pack, Seung Pil; Annaluru, Narayana; Kodaki, Tsutomu; Makino, Keisuke

2007-09-01

A recombinant Saccharomyces cerevisiae strain transformed with xylose reductase (XR) and xylitol dehydrogenase (XDH) genes from Pichia stipitis (PsXR and PsXDH, respectively) has the ability to convert xylose to ethanol together with the unfavourable excretion of xylitol, which may be due to intercellular redox imbalance caused by the different coenzyme specificity between NADPH-preferring XR and NAD(+)-dependent XDH. In this study, we focused on the effect(s) of mutated NADH-preferring PsXR in fermentation. The R276H and K270R/N272D mutants were improved 52- and 146-fold, respectively, in the ratio of NADH/NADPH in catalytic efficiency [(k(cat)/K(m) with NADH)/(k(cat)/K(m) with NADPH)] compared with the wild-type (WT), which was due to decrease of k(cat) with NADPH in the R276H mutant and increase of K(m) with NADPH in the K270R/N272D mutant. Furthermore, R276H mutation led to significant thermostabilization in PsXR. The most positive effect on xylose fermentation to ethanol was found by using the Y-R276H strain, expressing PsXR R276H mutant and PsXDH WT: 20 % increase of ethanol production and 52 % decrease of xylitol excretion, compared with the Y-WT strain expressing PsXR WT and PsXDH WT. Measurement of intracellular coenzyme concentrations suggested that maintenance of the of NADPH/NADP(+) and NADH/NAD(+) ratios is important for efficient ethanol fermentation from xylose by recombinant S. cerevisiae.

Evaluation of the feasibility of switching from immediate release quetiapine to extended release quetiapine fumarate in stable outpatients with schizophrenia.

PubMed

Möller, Hans-Jürgen; Johnson, Sunny; Mateva, Temenuzhka; Brecher, Martin; Svensson, Ola; Miller, Frank; Meulien, Didier

2008-03-01

This double-blind, double-dummy study (D1444C00146) evaluated the efficacy and safety of switching patients with clinically stable schizophrenia from quetiapine immediate release (IR) to the same dose of once-daily extended release quetiapine fumarate (quetiapine XR). Patients received quetiapine IR 400-800 mg/day twice daily for 4 weeks, and were then randomized (2 : 1) to a once-daily equivalent dose of quetiapine XR or maintained on IR for 6 weeks. The primary variable was the proportion of patients who discontinued treatment owing to lack of efficacy or whose Positive and Negative Syndrome Scale scores increased by at least 20% from randomization to any visit. In total, 497 patients were randomized to quetiapine XR (n=331) or IR (n=166). Noninferiority (6% margin; one-sided test, 2.5% significance level) was narrowly missed for the primary efficacy variable for the modified intention-to-treat population (9.1%, quetiapine XR; 7.2%, quetiapine IR; difference 1.86%; 95% confidence interval: -3.78, 6.57; P=0.0431), but was shown for the per-protocol population (5.3%, quetiapine XR; 6.2%, quetiapine IR; difference: -0.83%; 95% confidence interval: -6.75, 3.71; P=0.0017). Serious adverse event incidence was low for quetiapine XR and IR; there were no unexpected adverse events. In conclusion, efficacy was maintained without compromising safety/tolerability when switching patients with stable schizophrenia from twice-daily quetiapine IR to once-daily quetiapine XR (400-800 mg/day).

Associated factors of atrophic gastritis diagnosed by double-contrast upper gastrointestinal barium X-ray radiography: a cross-sectional study analyzing 6,901 healthy subjects in Japan.

PubMed

Yamamichi, Nobutake; Hirano, Chigaya; Shimamoto, Takeshi; Minatsuki, Chihiro; Takahashi, Yu; Nakayama, Chiemi; Matsuda, Rie; Fujishiro, Mitsuhiro; Konno-Shimizu, Maki; Kato, Jun; Kodashima, Shinya; Ono, Satoshi; Niimi, Keiko; Mochizuki, Satoshi; Tsuji, Yosuke; Sakaguchi, Yoshiki; Asada-Hirayama, Itsuko; Takeuchi, Chihiro; Yakabi, Seiichi; Kakimoto, Hikaru; Wada, Ryoichi; Mitsushima, Toru; Ichinose, Masao; Koike, Kazuhiko

2014-01-01

Double-contrast upper gastrointestinal barium X-ray radiography (UGI-XR) is one of the most widely conducted gastric cancer screening methods. It has been executed to find gastric cancer, but has not been usually executed to detect premalignant atrophic mucosa of stomach. To understand the meaning of UGI-XR-based atrophic gastritis, we analyzed its association with several causative factors including Helicobacter pylori (HP) infection. We evaluated 6,901 healthy adults in Japan. UGI-XR-based atrophic gastritis was diagnosed based on the irregular shape of areae gastricae and its expansion in the stomach. Of the 6,433 subjects with no history of HP eradication and free from gastric acid suppressants, 1,936 were diagnosed as UGI-XR-based atrophic gastritis (mild: 234, moderate: 822, severe: 880). These were univariately associated with serum HP IgG and serum pepsinogen I/II ratio with statistical significance. The multiple logistic analysis calculating standardized coefficients (β) and odds ratio (OR) demonstrated that serum HP IgG (β = 1.499, OR = 4.48), current smoking (β = 0.526, OR = 1.69), age (β = 0.401, OR = 1.49), low serum pepsinogen I/II ratio (β = 0.339, OR = 1.40), and male gender (β = 0.306, OR = 1.36) showed significant positive association with UGI-XR-based atrophic gastritis whereas drinking and body mass index did not. Among the age/sex/smoking/drinking-matched 227 pairs derived from chronically HP-infected and successfully HP-eradicated subjects, UGI-XR-based atrophic gastritis was detected in 99.1% of the former but in only 59.5% of the latter subjects (p<0.0001). Contrastively, UGI-XR-based atrophic gastritis was detected in 13 of 14 HP-positive proton pump inhibitor users (92.9%) and 33 of 34 HP-positive histamine H2-receptor antagonist users (97.1%), which are not significantly different from gastric acid suppressant-free subjects. The presence of UGI-XR-based atrophic gastritis is positively associated with Helicobacter pylori infection, current smoking, age, decreased serum pepsinogen I/II ratio, and male gender. Eradication of Helicobacter pylori seems to superficially improve UGI-XR-based atrophic gastritis whereas intake of gastric acid suppressants does not.

Associated Factors of Atrophic Gastritis Diagnosed by Double-Contrast Upper Gastrointestinal Barium X-Ray Radiography: A Cross-Sectional Study Analyzing 6,901 Healthy Subjects in Japan

PubMed Central

Yamamichi, Nobutake; Hirano, Chigaya; Shimamoto, Takeshi; Minatsuki, Chihiro; Takahashi, Yu; Nakayama, Chiemi; Matsuda, Rie; Fujishiro, Mitsuhiro; Konno-Shimizu, Maki; Kato, Jun; Kodashima, Shinya; Ono, Satoshi; Niimi, Keiko; Mochizuki, Satoshi; Tsuji, Yosuke; Sakaguchi, Yoshiki; Asada-Hirayama, Itsuko; Takeuchi, Chihiro; Yakabi, Seiichi; Kakimoto, Hikaru; Wada, Ryoichi; Mitsushima, Toru; Ichinose, Masao; Koike, Kazuhiko

2014-01-01

Background Double-contrast upper gastrointestinal barium X-ray radiography (UGI-XR) is one of the most widely conducted gastric cancer screening methods. It has been executed to find gastric cancer, but has not been usually executed to detect premalignant atrophic mucosa of stomach. To understand the meaning of UGI-XR-based atrophic gastritis, we analyzed its association with several causative factors including Helicobacter pylori (HP) infection. Methods We evaluated 6,901 healthy adults in Japan. UGI-XR-based atrophic gastritis was diagnosed based on the irregular shape of areae gastricae and its expansion in the stomach. Results Of the 6,433 subjects with no history of HP eradication and free from gastric acid suppressants, 1,936 were diagnosed as UGI-XR-based atrophic gastritis (mild: 234, moderate: 822, severe: 880). These were univariately associated with serum HP IgG and serum pepsinogen I/II ratio with statistical significance. The multiple logistic analysis calculating standardized coefficients (β) and odds ratio (OR) demonstrated that serum HP IgG (β = 1.499, OR = 4.48), current smoking (β = 0.526, OR = 1.69), age (β = 0.401, OR = 1.49), low serum pepsinogen I/II ratio (β = 0.339, OR = 1.40), and male gender (β = 0.306, OR = 1.36) showed significant positive association with UGI-XR-based atrophic gastritis whereas drinking and body mass index did not. Among the age/sex/smoking/drinking-matched 227 pairs derived from chronically HP-infected and successfully HP-eradicated subjects, UGI-XR-based atrophic gastritis was detected in 99.1% of the former but in only 59.5% of the latter subjects (p<0.0001). Contrastively, UGI-XR-based atrophic gastritis was detected in 13 of 14 HP-positive proton pump inhibitor users (92.9%) and 33 of 34 HP-positive histamine H2-receptor antagonist users (97.1%), which are not significantly different from gastric acid suppressant-free subjects. Conclusions The presence of UGI-XR-based atrophic gastritis is positively associated with Helicobacter pylori infection, current smoking, age, decreased serum pepsinogen I/II ratio, and male gender. Eradication of Helicobacter pylori seems to superficially improve UGI-XR-based atrophic gastritis whereas intake of gastric acid suppressants does not. PMID:25343257

Mixed-Amphetamine Salts Increase Abstinence From Marijuana in Patients With Co-Occurring Attention-Deficit/Hyperactivity Disorder and Cocaine Dependence

PubMed Central

Notzon, Daniel P.; Mariani, John J.; Pavlicova, Martina; Glass, Andrew; Mahony, Amy L.; Brooks, Daniel J.; Grabowski, John; Levin, Frances R.

2017-01-01

Background and Objectives The prevalence of ADHD is greater in substance use disorders than the general population, and ADHD and substance use disorders share neurobiological features such as dysregulation of reward circuitry. We tested the hypothesis that stimulants would decrease marijuana use in a randomized controlled trial of extended release mixed amphetamine salts (MAS-XR) for treatment of co-occurring ADHD and cocaine use disorders. Methods Marijuana users were defined as participants reporting use in the 30 days before study initiation, collected with timeline follow-back. The original 14-week trial utilized a 3-arm randomized design, comparing placebo, MAS-XR 60 mg, and MAS-XR 80 mg. For this analysis, both MAS-XR groups were combined, leaving n = 20 in the placebo group and n = 37 in the MAS-XR group. The primary outcome was proportion of subjects reporting any marijuana use per study week. Comparisons between groups were made using a logistic mixed effects model incorporating multiple predictors and modeling time-by-treatment interactions. Results There were no significant baseline differences in marijuana use frequency and quantity. There was a significant decrease in the proportion of participants using marijuana over time in the MAS-XR group, but no difference in the proportion of marijuana-use days over time. Discussion and Conclusions Treatment of ADHD and comorbid cocaine use disorders with MAS-XR is associated with increased weekly abstinence from marijuana but not with a decrease in the proportion of marijuana using days per week. Scientific Significance Stimulant treatment of ADHD and cocaine use disorders may diminish co-occurring cannabis use. PMID:28051838

Extended-Release Once-Daily Formulation of Tofacitinib: Evaluation of Pharmacokinetics Compared With Immediate-Release Tofacitinib and Impact of Food.

PubMed

Lamba, Manisha; Wang, Rong; Fletcher, Tracey; Alvey, Christine; Kushner, Joseph; Stock, Thomas C

2016-11-01

Tofacitinib is an oral Janus kinase inhibitor for the treatment of rheumatoid arthritis. An extended-release (XR) formulation has been designed to provide a once-daily (QD) dosing option to patients to achieve comparable pharmacokinetic (PK) parameters to the twice-daily immediate-release (IR) formulation. We conducted 2 randomized, open-label, phase 1 studies in healthy volunteers. Study A characterized single-dose and steady-state PK of tofacitinib XR 11 mg QD and intended to demonstrate equivalence of exposure under single-dose and steady-state conditions to tofacitinib IR 5 mg twice daily. Study B assessed the effect of a high-fat meal on the bioavailability of tofacitinib from the XR formulation. Safety and tolerability were monitored in both studies. In study A (N = 24), the XR and IR formulations achieved time to maximum plasma concentration at 4 hours and 0.5 hours postdose, respectively; terminal half-life was 5.9 hours and 3.2 hours, respectively. Area under plasma concentration-time curve (AUC) and maximum plasma concentration (C max ) after single- and multiple-dose administration were equivalent between the XR and IR formulations. In study B (N = 24), no difference in AUC was observed for fed vs fasted conditions. C max increased by 27% under the fed state. On repeat administration, negligible accumulation (<20%) of systemic exposures was observed for both formulations. Steady state was achieved within 48 hours of dosing with the XR formulation. Tofacitinib administration as an XR or IR formulation was generally well tolerated in these studies. © 2016, The Authors. The Journal of Clinical Pharmacology published by Wiley Periodicals, Inc. on behalf of American College of Clinical Pharmacology.

Mixed-amphetamine salts increase abstinence from marijuana in patients with co-occurring attention-deficit/hyperactivity disorder and cocaine dependence.

PubMed

Notzon, Daniel P; Mariani, John J; Pavlicova, Martina; Glass, Andrew; Mahony, Amy L; Brooks, Daniel J; Grabowski, John; Levin, Frances R

2016-12-01

The prevalence of ADHD is greater in substance use disorders than the general population, and ADHD and substance use disorders share neurobiological features such as dysregulation of reward circuitry. We tested the hypothesis that stimulants would decrease marijuana use in a randomized controlled trial of extended release mixed amphetamine salts (MAS-XR) for treatment of co-occurring ADHD and cocaine use disorders. Marijuana users were defined as participants reporting use in the 30 days before study initiation, collected with timeline follow-back. The original 14-week trial utilized a 3-arm randomized design, comparing placebo, MAS-XR 60 mg, and MAS-XR 80 mg. For this analysis, both MAS-XR groups were combined, leaving n = 20 in the placebo group and n = 37 in the MAS-XR group. The primary outcome was proportion of subjects reporting any marijuana use per study week. Comparisons between groups were made using a logistic mixed effects model incorporating multiple predictors and modeling time-by-treatment interactions. There were no significant baseline differences in marijuana use frequency and quantity. There was a significant decrease in the proportion of participants using marijuana over time in the MAS-XR group, but no difference in the proportion of marijuana-use days over time. Treatment of ADHD and comorbid cocaine use disorders with MAS-XR is associated with increased weekly abstinence from marijuana but not with a decrease in the proportion of marijuana using days per week. Stimulant treatment of ADHD and cocaine use disorders may diminish co-occurring cannabis use. (Am J Addict 2016;25:666-672). © 2016 American Academy of Addiction Psychiatry.

A randomized crossover study to assess the pharmacokinetics of a novel amphetamine extended-release orally disintegrating tablet in healthy adults.

PubMed

Stark, Jeffrey G; Engelking, Dorothy; McMahen, Russ; Sikes, Carolyn

2016-09-01

In this pharmacokinetic (PK) study in healthy adults, we sought to: (1) compare the PK properties of a novel amphetamine extended-release orally disintegrating tablet formulation (Adzenys XR-ODT™ [AMP XR-ODT]) to a reference extended-release mixed amphetamine salts (MAS ER) formulation and (2) assess the effect of food on AMP XR-ODT. Forty-two adults were enrolled in a single-dose, open-label, 3-period, 3-treatment, randomized crossover study and received an 18.8-mg dose of AMP XR-ODT (fasted or fed) or equivalent dose (30 mg) of MAS ER (fasted). Plasma samples were analyzed for d-and l-amphetamine. Maximum plasma concentration (Cmax), time to maximum plasma concentration (Tmax), elimination half-life (T1/2), area under the concentration-time curve from time zero to last quantifiable concentration (AUClast), from time zero to infinity (AUCinf), relevant partial AUCs, and weight-normalized clearance (CL/F/kg) were assessed. The PK parameters were compared across treatments using an ANOVA. Safety was also assessed. A total of 39 adults completed this study. The geometric mean ratios (90% confidence interval [CI]) for AMP XR-ODT/MAS ER Cmax, AUC5-last, AUClast, and AUCinf were within 80%-125% for both d-and l-amphetamine. The 90% CIs for AUC0-5 were slightly below the 80%-125% range. When AMP XR-ODT was administered with food, there was a slight decrease in the d-and l-amphetamine Cmax and approximately a 2-hour delay in Tmax. The most common adverse events reported (>5% of participants) were dry mouth, palpitations, nausea, dizziness, headache, anxiety, and nasal congestion. AMP XR-ODT displayed a PK profile similar to MAS ER, and no clinically relevant food effect was observed.

Opioid use and dropout in patients receiving oral naltrexone with or without single administration of injection naltrexone

PubMed Central

Sullivan, Maria A.; Bisaga, Adam; Glass, Andrew; Mishlen, Kaitlyn; Pavlicova, Martina; Carpenter, Kenneth M.; Mariani, John J; Levin, Frances R.; Nunes, Edward V.

2015-01-01

Background Adherence to oral naltrexone has been poor and can be improved somewhat with behavioral therapy. We compared Behavioral Naltrexone Therapy (BNT) to Compliance Enhancement (CE) and tested efficacy of single-dose injection naltrexone (XR-NTX; 384 mg) with behavioral therapies at further improving aherence to oral naltrexone. Methods A 24-week, randomized, placebo-controlled trial (N=125) compared four treatment conditions following inpatient detoxification and oral naltrexone induction: (1) BNT+XR-NTX; (2) BNT+ placebo injection; (3) CE+ XR-NTX; and (4) CE+placebo injection. All participants were maintained on oral naltrexone throughout the trial. Primary outcome was retention in treatment. Results Of 89 randomized participants, 78.7% (70/89) completed 4 weeks, 58.2% (54/89) completed 8 weeks, 47.2% (42/89) completed 12 weeks, and 25.8% (23/89) completed 24 weeks. A Cox proportional hazards regression modeled time to dropout as a function of treatment condition, baseline opioid dependence severity (bags per day of heroin use), and their interaction. Interaction of conditions by baseline severity was significant (X23 = 9.19, p = .027). For low-severity patients (<6 bags/day), retention was highest in the BNT-XRNTX group (60% at 6 months), as hypothesized. For high-severity (> 6 bags/day) patients, BNT-XR-NTX did not perform as well, due to high early attrition. Conclusion For low-severity heroin users, single-dose XR-NTX improved long-term treatment retention when combined with behavioral therapy. In higher-severity opioid-dependent patients, XR-NTX was less helpful, perhaps because, combined with oral naltrexone, it produced higher blood levels and more withdrawal discomfort. When cost considerations recommend oral naltrexone following XR-NTX, the latter should be phased in slowly. PMID:25555621

ACTOplus Met XR in Treating Patients With Stage I-IV Oral Cavity or Oropharynx Cancer Undergoing Definitive Treatment | Division of Cancer Prevention

Cancer.gov

This randomized phase IIb trial studies how well ACTOplus met XR works in treating in patients with stage I-IV oral cavity or oropharynx cancer that are undergoing definitive treatment. Chemoprevention is the use of drugs to keep oral cavity or oropharynx cancer from forming or coming back. The use of ACTOplus met XR may slow disease progression in patients with oral cavity or

Effects of NADH-preferring xylose reductase expression on ethanol production from xylose in xylose-metabolizing recombinant Saccharomyces cerevisiae.

PubMed

Lee, Sung-Haeng; Kodaki, Tsutomu; Park, Yong-Cheol; Seo, Jin-Ho

2012-04-30

Efficient conversion of xylose to ethanol is an essential factor for commercialization of lignocellulosic ethanol. To minimize production of xylitol, a major by-product in xylose metabolism and concomitantly improve ethanol production, Saccharomyces cerevisiae D452-2 was engineered to overexpress NADH-preferable xylose reductase mutant (XR(MUT)) and NAD⁺-dependent xylitol dehydrogenase (XDH) from Pichia stipitis and endogenous xylulokinase (XK). In vitro enzyme assay confirmed the functional expression of XR(MUT), XDH and XK in recombinant S. cerevisiae strains. The change of wild type XR to XR(MUT) along with XK overexpression led to reduction of xylitol accumulation in microaerobic culture. More modulation of the xylose metabolism including overexpression of XR(MUT) and transaldolase, and disruption of the chromosomal ALD6 gene encoding aldehyde dehydrogenase (SX6(MUT)) improved the performance of ethanol production from xylose remarkably. Finally, oxygen-limited fermentation of S. cerevisiae SX6(MUT) resulted in 0.64 g l⁻¹ h⁻¹ xylose consumption rate, 0.25 g l⁻¹ h⁻¹ ethanol productivity and 39% ethanol yield based on the xylose consumed, which were 1.8, 4.2 and 2.2 times higher than the corresponding values of recombinant S. cerevisiae expressing XR(MUT), XDH and XK only. Copyright © 2011 Elsevier B.V. All rights reserved.

Spotlight on amoxicillin/clavulanic acid 2000 mg/125 mg extended release (XR) in respiratory tract infections in adults.

PubMed

McCormack, Paul L; Keating, Gillian M

2005-01-01

Amoxicillin/clavulanic acid 2000 mg/125 mg extended release (Augmentin XR), referred to herein as amoxicillin/clavulanic acid XR, is a pharmacokinetically enhanced formulation designed to provide more effective therapy in adults and adolescents than conventional formulations against community-acquired respiratory tract pathogens, particularly Streptococcus pneumoniae, with reduced susceptibility to amoxicillin.Amoxicillin/clavulanic acid XR maintains plasma amoxicillin concentrations >4 microg/mL for a mean of 49% of the dosing interval indicating that it would be highly effective against S. pneumoniae strains with minimum inhibitory concentrations (MICs) above the National Committee for Clinical Laboratory Standard's amoxicillin +/- clavulanic acid susceptibility breakpoint of < or = 2 microg/mL. Amoxicillin/clavulanic acid XR is at least as effective as conventional amoxicillin/clavulanic acid formulations, levofloxacin, and clarithromycin in treating community-acquired pneumonia, acute bacterial sinusitis, or acute exacerbations of chronic bronchitis, and has a tolerability profile comparable to that of conventional amoxicillin/clavulanic acid formulations. While the incidence of amoxicillin- or multidrug-resistant S. pneumoniae is not currently sufficient in most regions to warrant the routine empiric use of amoxicillin/clavulanic acid XR, the drug would be extremely useful in those regions with a high incidence of resistant pathogens or in selected patients (i.e. those with S. pneumoniae isolates having amoxicillin MICs > or = 2 microg/mL but < or = 4 microg/mL).

Amoxicillin/clavulanic acid 2000mg/125mg extended release (XR): a review of its use in the treatment of respiratory tract infections in adults.

PubMed

McCormack, Paul L; Keating, Gillian M

2005-01-01

Amoxicillin/clavulanic acid 2000mg/125mg extended release (Augmentin XR), referred to herein as amoxicillin/clavulanic acid XR, is a pharmacokinetically enhanced formulation designed to provide more effective therapy in adults and adolescents than conventional formulations against community-acquired respiratory tract pathogens, particularly Streptococcus pneumoniae, with reduced susceptibility to amoxicillin. Amoxicillin/clavulanic acid XR maintains plasma amoxicillin concentrations above 4 microg/mL for a mean of 49% of the dosing interval indicating that it would be highly effective against S. pneumoniae strains with minimum inhibitory concentrations (MICs) above the National Committee for Clinical Laboratory Standard's amoxicillin +/- clavulanic acid susceptibility breakpoint of < or =2 microg/mL. Amoxicillin/clavulanic acid XR is at least as effective as conventional amoxicillin/clavulanic acid formulations, levofloxacin and clarithromycin in treating community-acquired pneumonia, acute bacterial sinusitis or acute exacerbations of chronic bronchitis, and has a tolerability profile comparable to that of conventional amoxicillin/clavulanic acid formulations. While the incidence of amoxicillin- or multidrug-resistant S. pneumoniae is not currently sufficient in most regions to warrant the routine empirical use of amoxicillin/clavulanic acid XR, the drug would be extremely useful in those regions with a high incidence of resistant pathogens or in selected patients (i.e. those with S. pneumoniae isolates having amoxicillin MICs > or =2 microg/mL but < or =4 microg/mL).

Systematic strain construction and process development: Xylitol production by Saccharomyces cerevisiae expressing Candida tenuis xylose reductase in wild-type or mutant form.

PubMed

Pratter, S M; Eixelsberger, T; Nidetzky, B

2015-12-01

A novel Saccharomyces cerevisiae whole-cell biocatalyst for xylitol production based on Candida tenuis xylose reductase (CtXR) is presented. Six recombinant strains expressing wild-type CtXR or an NADH-specific mutant were constructed and evaluated regarding effects of expression mode, promoter strength, biocatalyst concentration and medium composition. Intracellular XR activities ranged from 0.09 U mgProt(-1) to 1.05 U mgProt(-1) but did not correlate with the strains' xylitol productivities, indicating that other factors limited xylose conversion in the high-activity strains. The CtXR mutant decreased the biocatalyst's performance, suggesting use of the NADPH-preferring wild-type enzyme when (semi-)aerobic conditions are applied. In a bioreactor process, the best-performing strain converted 40 g L(-1) xylose with an initial productivity of 1.16 g L(-1)h(-1) and a xylitol yield of 100%. The obtained results underline the potential of CtXR wild-type for xylose reduction and point out parameters to improve "green" xylitol production. Copyright © 2015 Elsevier Ltd. All rights reserved.

Intensity transitions in Cyg XR-1 observed at high energies from OSO 8

NASA Technical Reports Server (NTRS)

Dolan, J. F.; Crannell, C. J.; Dennis, B. R.; Frost, K. J.; Orwig, L. E.

1977-01-01

The observed transitions at energies above 20 keV show that the spectrum of Cyg XR-1 exhibits the pivoting effect during intensity transitions expected from two-temperature accretion disk models of the X-ray emitting region. Cyg XR-1 was observed with the high-energy X-ray spectrometer on board the OSO-8 satellite from November 11-19, 1975 and from October 27 to November 15, 1976 (excluding the period from November 1 to November 7, 1976).

Correlation and Reliability of Cervical Sagittal Alignment Parameters between Lateral Cervical Radiograph and Lateral Whole-Body EOS Stereoradiograph.

PubMed

Singhatanadgige, Weerasak; Kang, Daniel G; Luksanapruksa, Panya; Peters, Colleen; Riew, K Daniel

2016-09-01

Retrospective analysis. To evaluate the correlation and reliability of cervical sagittal alignment parameters obtained from lateral cervical radiographs (XRs) compared with lateral whole-body stereoradiographs (SRs). We evaluated adults with cervical deformity using both lateral XRs and lateral SRs obtained within 1 week of each other between 2010 and 2014. XR and SR images were measured by two independent spine surgeons using the following sagittal alignment parameters: C2-C7 sagittal Cobb angle (SCA), C2-C7 sagittal vertical axis (SVA), C1-C7 translational distance (C1-7), T1 slope (T1-S), neck tilt (NT), and thoracic inlet angle (TIA). Pearson correlation and paired t test were used for statistical analysis, with intra- and interrater reliability analyzed using intraclass correlation coefficient (ICC). A total of 35 patients were included in the study. We found excellent intrarater reliability for all sagittal alignment parameters in both the XR and SR groups with ICC ranging from 0.799 to 0.994 for XR and 0.791 to 0.995 for SR. Interrater reliability was also excellent for all parameters except NT and TIA, which had fair reliability. We also found excellent correlations between XR and SR measurements for most sagittal alignment parameters; SCA, SVA, and C1-C7 had r > 0.90, and only NT had r < 0.70. There was a significant difference between groups, with SR having lower measurements compared with XR for both SVA (0.68 cm lower, p < 0.001) and C1-C7 (1.02 cm lower, p < 0.001). There were no differences between groups for SCA, T1-S, NT, and TIA. Whole-body stereoradiography appears to be a viable alternative for measuring cervical sagittal alignment parameters compared with standard radiography. XR and SR demonstrated excellent correlation for most sagittal alignment parameters except NT. However, SR had significantly lower average SVA and C1-C7 measurements than XR. The lower radiation exposure using single SR has to be weighed against its higher cost compared with XR.

A randomized, double-blind study of the efficacy and tolerability of extended-release quetiapine fumarate (quetiapine XR) monotherapy in patients with major depressive disorder

PubMed Central

Wang, Gang; McIntyre, Alexander; Earley, Willie R; Raines, Shane R; Eriksson, Hans

2014-01-01

Objectives To evaluate the efficacy and tolerability of once-daily extended release quetiapine fumarate (quetiapine XR) monotherapy in patients with major depressive disorder (MDD). Patients and methods This was a 10-week (8-week active treatment/2-week post-treatment) randomized, double-blind, placebo- and active-controlled study (D1448C00004). Patients received quetiapine XR 150 mg/day, escitalopram 10 mg/day, or placebo; patients with an inadequate response (<20% improvement in Montgomery–Åsberg Depression Rating Scale [MADRS] total score) at week two received double-dose treatment. The primary end point was week eight change from randomization in MADRS total score. Secondary end points included MADRS response (≥50% improvement) and remission (score ≤8); Hamilton Rating Scale for Depression total and item 1; Hamilton Rating Scale for Anxiety total, psychic, and somatic; Clinical Global Impressions – Severity of Illness total; Pittsburgh Sleep Quality Index (PSQI) global; and Quality of Life Enjoyment and Satisfaction Questionnaire – Short Form percentage maximum total scores. Tolerability was assessed throughout. Results A total of 471 patients was randomized. No significant improvements in MADRS total score were observed at week eight (last observation carried forward) with either active treatment (quetiapine XR, −17.21 [P=0.174]; escitalopram, −16.73 [P=0.346]) versus placebo (−15.61). There were no significant differences in secondary end points versus placebo, with the exception of week-eight change in PSQI global score (quetiapine XR, −4.96 [P<0.01] versus placebo, −3.37). Mixed-model repeated-measures analysis of observed-case data suggested that the primary analysis may not be robust. Most commonly reported adverse events included dry mouth, somnolence, and dizziness for quetiapine XR, and headache and nausea for escitalopram. Conclusion In this study, neither quetiapine XR (150/300 mg/day) nor escitalopram (10/20 mg/day) showed significant separation from placebo. Both compounds have been shown previously to be effective in the treatment of MDD; possible reasons for this failed study are discussed. Quetiapine XR was generally well tolerated, with a profile similar to that reported previously. PMID:24511235

Climate for Women in Industry: the Xerox Approach - An Example from the Division of Xerox Research and Technology

NASA Astrophysics Data System (ADS)

Chang, Shu

2000-03-01

Xerox has a very favorable reputation as an employer for women. In 1998, Xerox was cited three times as a top company for working women. "Working Mother" magazine, for the 13th consecutive year, chose Xerox as one of the 100 best companies for working mothers. "Working Women" magazine included Xerox as one of the top 25 public companies in the United States for executive women. "Latina Style" named Xerox as one of the 50 companies that offer the best professional opportunities for Hispanic women. However, Xerox is striving to be the employer of choice for women. Xerox views diversity as a business necessity and is beyond numbers and targets. To Xerox, diversity brings ideas, perspectives, and creativity that lead to more innovative solutions. To become the employer of choice for women, the approach from the Xerox Research and Technology organization (XR&T) is to improve the recruitment, retention, and advancement of women. The measurement of the improvement is an increasing representation of women at all levels. Championed by Dr. Mark B. Myers, Senior Vice President and head of XR&T, a dual effort has been implemented. At the request of Dr. Myers, an XR&T Women’s Council was formed in 1991. The mission of the Council has been to identify and promote opportunities for improving the work environment to support diversity and to advise XR&T management how to achieve this goal. Along with the Council, the mission of the XR&T management has been to follow through with Dr. Myers’ directions, Xerox policies, and the Council’s recommendations. By persistency, this dual effort is now paying off. Since 1991, the number of women among new hires and promotions has been steadily increasing. As for retention, XR&T is continuously creating, improving, and communicating policies and practices on career development programs, BWF tracking, diversity training, etc. Due to these proactive actions, a more supportive climate for women is emerging in XR&T. In our talk, we will discuss in more detail on the XR&T parallel effort and its consequence.

A placebo controlled study of quetiapine-XR in bipolar depression accompanied by generalized anxiety with and without a recent history of alcohol and cannabis use.

PubMed

Gao, Keming; Ganocy, Stephen J; Conroy, Carla; Brownrigg, Brittany; Serrano, Mary Beth; Calabrese, Joseph R

2017-08-01

This study aims to compare treatment response in bipolar I or II depression and generalized anxiety disorder (GAD) with and without recent alcohol and/or cannabis use disorder (ALC/CAN) to quetiapine-XR (extended release) or placebo. A randomized, double-blind, 8-week study of quetiapine-XR versus placebo in patients with bipolar I or II depression and GAD with or without a recent ALC/CAN was used to compare changes in Hamilton Depression Rating Scale-17, Hamilton Anxiety Rating Scale, the 16-item Quick Inventory of Depressive Symptomatology-Self-Report (QIDS-SR-16), Clinical Global Impression for Bipolar Disorder-Severity (CGI-BP-S), and Timeline Follow Back within and between groups. In the quetiapine-XR group, patients with a recent ALC/CAN (n = 22) had significant decreases in QIDS-SR-16 (-9.6 ± 1.6 vs. -3.7 ± 1.7) and CGI-BP-S (-1.6 ± 0.4 vs. -0.8 ± 0.03) than those without a recent ALC/CAN (n = 24). In the placebo group, both patients with a recent ALC/CAN (n = 23) and those without (n = 21) had similar reductions in these measures. The reduction of QIDS-SR-16 scores in patients with a recent ALC/CAN was also significantly different from that of their counterparts in the placebo group. Patients who received quetiapine-XR had larger decreases in the number of drinking days/week (p = 0.17) and number of cannabis joints/week (p = 0.09) compared to those who received placebo. Quetiapine-XR was superior to placebo in reducing QIDS-SR-16 total score in patients with a recent ALC/CAN. Patients taking quetiapine-XR used less alcohol and cannabis than patients on placebo, suggesting that quetiapine-XR may be of use in patients with bipolar disorder accompanied by GAD and other comorbidities.

Molten Chloride Salts for Heat Transfer in Nuclear Systems

NASA Astrophysics Data System (ADS)

Ambrosek, James Wallace

2011-12-01

A forced convection loop was designed and constructed to examine the thermal-hydraulic performance of molten KCl-MgCl2 (68-32 at %) salt for use in nuclear co-generation facilities. As part of this research, methods for prediction of the thermo-physical properties of salt mixtures for selection of the coolant salt were studied. In addition, corrosion studies of 10 different alloys were exposed to the KCl-MgCl2 to determine a suitable construction material for the loop. Using experimental data found in literature for unary and binary salt systems, models were found, or developed to extrapolate the available experimental data to unstudied salt systems. These property models were then used to investigate the thermo-physical properties of the LINO3-NaNO3-KNO 3-Ca(NO3), system used in solar energy applications. Using these models, the density, viscosity, adiabatic compressibility, thermal conductivity, heat capacity, and melting temperatures of higher order systems can be approximated. These models may be applied to other molten salt systems. Coupons of 10 different alloys were exposed to the chloride salt for 100 hours at 850°C was undertaken to help determine with which alloy to construct the loop. Of the alloys exposed, Haynes 230 had the least amount of weight loss per area. Nickel and Hastelloy N performed best based on maximum depth of attack. Inconel 625 and 718 had a nearly uniform depletion of Cr from the surface of the sample. All other alloys tested had depletion of Cr along the grain boundaries. The Nb in Inconel 625 and 718 changed the way the Cr is depleted in these alloys. Grain-boundary engineering (GBE) of Incoloy 800H improved the corrosion resistance (weight loss and maximum depth of attack) by nearly 50% as compared to the as-received Incoloy 800H sample. A high temperature pump, thermal flow meter, and pressure differential device was designed, constructed and tested for use in the loop, The heat transfer of the molten chloride salt was found to follow general correlations used to estimate the Nusselt number for water in both the forced convection laminar regime and in the mixed convection regime.

A clinical evaluation of the ProNOVA XR polymer-free sirolimus eluting coronary stent system in the treatment of patients with de novo coronary artery lesions (EURONOVA XR I study)☆

PubMed Central

Legutko, Jacek; Zasada, Wojciech; Kałuża, Grzegorz L.; Heba, Grzegorz; Rzeszutko, Lukasz; Jakala, Jacek; Dragan, Jacek; Klecha, Artur; Giszterowicz, Dawid; Dobrowolski, Wojciech; Partyka, Łukasz; Jayaraman, Swaminathan; Dudek, Dariusz

2013-01-01

Aims Evaluation of safety and efficacy of ProNOVA XR, a new generation of polymer-free sirolimus eluting stents (SES), utilizing a pharmaceutical excipient for timed release of sirolimus from the XR platform. Methods and results Safety and efficacy of ProNOVA XR coronary stent system was examined in EURONOVA prospective, single arm, multi-center registry of 50 patients with de novo native coronary lesions up to 28 mm in length in arteries between 2.25 and 4 mm. At 6-month, in-stent late lumen loss by QCA was 0.45 ± 0.41 mm and in-stent neointimal volume obstruction in the IVUS sub-study was 14 ± 11%. One-year clinical follow-up revealed a favorable safety profile, with 2% of in-hospital MACE and 6.4% of MACE from hospital discharge up to 12 months (including 1 cardiac death >30 days after stent implantation and 2 TLRs). According to the ARC definition, there was no definite or probable stent thrombosis and 1 possible stent thrombosis (2%) up to 12 months of clinical follow-up. Conclusions In this preliminary evaluation, ProNOVA XR polymer-free sirolimus eluting stent system appeared safe with an early promise of adequate effectiveness in the treatment of de novo coronary lesions in up to 12 months of clinical, angiographic and IVUS follow-up. PMID:23992999

Weight change during long-term treatment with lurasidone: pooled analysis of studies in patients with schizophrenia.

PubMed

Meyer, Jonathan M; Mao, Yongcai; Pikalov, Andrei; Cucchiaro, Josephine; Loebel, Antony

2015-11-01

The objective of this analysis was to evaluate the effect of 12 months of treatment with lurasidone on weight in patients with schizophrenia. Post-hoc, observed-case analysis included pooled data from six studies on 40-160 mg/day lurasidone; two studies included active comparators (2-6 mg/day risperidone or 200-800 mg/day quetiapine XR). Overall, 593 patients completed 12 months of treatment (N=471 lurasidone, N = 89 risperidone, N = 33 quetiapine XR). The mean baseline weight was 72.8, 80.8, and 72.4 kg in the lurasidone, risperidone, and quetiapine XR groups, respectively. The mean weight change at month 12 was -0.4 kg with lurasidone, +2.6 kg with risperidone, and +1.2 kg with quetiapine XR. Weight gain of at least 7% from study baseline was observed in 16.0, 25.8, and 15.2% of patients, and weight loss of at least 7% was seen in 18.5, 6.7, and 9.1% of patients treated with lurasidone, risperidone, and quetiapine XR, respectively. A shift from normal/underweight baseline BMI status to overweight/obese at month 12 occurred in 10.2, 27.6, and 15.0% of patients in the lurasidone, risperidone, and quetiapine XR groups, respectively. Conversely, 14.3, 1.7, and 7.7% of patients, respectively, shifted from overweight/obese to normal/underweight. In summary, a low potential for clinically significant weight gain was observed in patients with schizophrenia treated continuously with lurasidone for 12 months.

Presence of Tablet Remnants of Nevirapine Extended-Release in Stools and Its Impact on Virological Outcome in HIV-1-Infected Patients: A Prospective Cohort Study

PubMed Central

Lee, Yi-Chieh; Lin, Shu-Wen; Chen, Mao-Yuan; Chang, Sui-Yuan; Kuo, Ching-Hua; Sheng, Wang-Huei; Hsieh, Szu-Min; Sun, Hsin-Yun; Chang, Hsi-Yen; Wu, Mon-Ro; Liu, Wen-Chun; Wu, Pei-Ying; Yang, Shang-Ping; Zhang, Jun-Yu; Su, Yi-Ching; Luo, Yi-Zhen; Hung, Chien-Ching; Chang, Shan-Chwen

2015-01-01

Background Nevirapine extended-release (NVP-XR) taken once daily remains an effective antiretroviral agent for patients infected with HIV-1 strains that do not harbor resistance mutations. Presence of tablet remnants of NVP XR in stools was reported in 1.19% and 3.05% of subjects in two clinical trials. However, the prevalence may have been underestimated because the information was retrospectively collected in the studies. Methods Between April and December 2014, we prospectively inquired about the frequency of noticing tablet remnants of NVP XR in stools in HIV-1-infected patients who switched to antiretroviral regimens containing NVP XR plus 2 nucleos(t)ide reverse-transcriptase inhibitors. Patients were invited to participate in therapeutic drug monitoring of plasma concentrations of NVP 12 or 24 hours after taking the previous dose (C12 and C24, respectively) of NVP XR using high-performance liquid chromatography. The information on clinical characteristics, including plasma HIV RNA load and CD4 lymphocyte count, at baseline and during follow-up was recorded. Results During the 9-month study period, 272 patients switched to NVP XR-based regimens and 60 (22.1%) noticed tablet remnants of NVP XR in stools, in whom 54.2% reported noticing the tablet remnants at least once weekly. Compared with patients who did not notice tablet remnants, those who noticed tablet remnants had a higher mean CD4 lymphocyte count (629 vs 495 cells/mm3, P = 0.0002) and a similar mean plasma HIV RNA load (1.57 vs 1.61 log10 copies/mL, P = 0.76) on switch. At about 12 and 24 weeks after switch, patients who noticed tablet remnants continued to have a similar mean plasma HIV RNA load (1.39 vs 1.43 log10 copies/mL, P = 0.43; and 1.30 vs 1.37 log10 copies/mL, P = 0.26, respectively), but had a lower median NVP C12 (3640 vs 4730 ng/mL, P = 0.06), and a similar median NVP C24 (3220 vs 3330 ng/ml, P = 0.95) when compared with those who did not notice tablet remnants. Conclusions The presence of tablet remnants of NVP XR in stools is not uncommon in HIV-1-infected Taiwanese patients receiving NVP XR-based antiretroviral regimens, which does not have an adverse impact on the virological and immunological outcomes. PMID:26465325

Efficacy of venlafaxine extended-release capsules in nondepressed outpatients with generalized anxiety disorder: A 6-month randomized controlled trial.

PubMed

Gelenberg, A J; Lydiard, R B; Rudolph, R L; Aguiar, L; Haskins, J T; Salinas, E

2000-06-21

Generalized anxiety disorder (GAD) is a chronic disorder that is associated with debilitating psychic and somatic symptoms. Venlafaxine extended-release (XR) capsules have been shown to be effective in short-term treatment of patients with GAD without major depressive disorder (MDD), but long-term data are needed to establish whether this agent confers persistent benefits. To compare the 6-month efficacy and safety of a flexible dosage of venlafaxine XR in outpatients with GAD without associated MDD. Six-month, randomized, double-blind, placebo-controlled, parallel-group trial conducted May 1996 to October 1997. Fourteen outpatient clinics and private psychiatric practices in the United States. A total of 251 outpatients aged 18 years or older who met Diagnostic and Statistical Manual of Mental Disorders, Fourth Edition (DSM-IV) criteria for GAD, had sufficient symptoms to require treatment, and did not have coexisting MDD. Participants were randomly assigned to receive either placebo (n=127) or venlafaxine XR (75, 150, or 225 mg/d, as required to control symptoms; n=124) for 28 weeks. Changes from baseline in the Hamilton Rating Scale for Anxiety (HAM-A) total score, the HAM-A psychic anxiety factor score, and the Clinical Global Impressions (CGI) scale Severity of Illness and Global Improvement scores, compared by intervention group. During weeks 6 through 28, response rates in the venlafaxine XR group were 69% or higher compared with rates of 42% to 46% in the placebo group (P<.001). By an evaluable-patient analysis, venlafaxine XR compared with placebo significantly improved anxiety scores from week 1 or 2 through week 28 on all primary efficacy measures, including the HAM-A total (P<.001), the HAM-A psychic anxiety factor (P<.001), and the CGI scale scores (P<.001). Adjusted mean changes from baseline to week 28 using last-observation-carried-forward methods were for HAM-A, venlafaxine XR -13.4, placebo -8.7 (P<.001); for HAM-A psychic anxiety score, venlafaxine XR -7.4, placebo -4.2 (P<.001); and for CGI-Improvement, venlafaxine XR 2.2, placebo 3.0 (P<.001). The most common treatment-emergent adverse event was nausea, followed by somnolence and dry mouth. This study is the first placebo-controlled demonstration of the long-term efficacy of any drug class in treating outpatients with DSM-IV-diagnosed GAD. Venlafaxine XR is an effective, rapidly acting, safe, once-daily agent for both the short- and long-term treatment of anxiety and may provide an important alternative to currently available anxiolytics. JAMA. 2000.

Tungsten wire-reinforced superalloys for 1093 C (2000 F) turbine blade applications

NASA Technical Reports Server (NTRS)

Friedman, G. I.; Fleck, J. N.

1979-01-01

Various combinations of fiber and matrix materials were fabricated and evaluated for the purpose of selecting a specific combination that exhibited the best overall properties for a turbine blade application. A total of seven matrix alloys, including Hastelloy X, Nimonic 80A, Inconel 600, Inconel 625, IN-102, FeCrA1Y, were investigated reinforced with either 218CS tungsten, or W-Hf-C fibers. Based on preliminary screening studies, FeCrA1Y, Inconel 600 and Inconel 625 matrix composites systems were selected for extended thermal cycle tests and for property evaluations which included stress rupture, impact, and oxidation resistance. Of those investigated, the FeCrA1Y matrix composite system exhibited the best overall properties required for a turbine blade application. The W-Hf-C/FeCrA1Y system was selected for further property evaluation. Tensile strength values of up to 724 MPa (105,000 psi) were obtained for this material at 982 C and 607 MPa at 1093 C.

System design description of forced-convection molten-salt corrosion loops MSR-FCL-3 and MSR-FCL-4

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huntley, W.R.; Silverman, M.D.

1976-11-01

Molten-salt corrosion loops MSR-FCL-3 and MSR-FCL-4 are high-temperature test facilities designed to evaluate corrosion and mass transfer of modified Hastelloy N alloys for future use in Molten-Salt Breeder Reactors. Salt is circulated by a centrifugal sump pump to evaluate material compatibility with LiF-BeF/sub 2/-ThF/sub 4/-UF/sub 4/ fuel salt at velocities up to 6 m/s (20 fps) and at salt temperatures from 566 to 705/sup 0/C (1050 to 1300/sup 0/F). The report presents the design description of the various components and systems that make up each corrosion facility, such as the salt pump, corrosion specimens, salt piping, main heaters, salt coolers,more » salt sampling equipment, and helium cover-gas system, etc. The electrical systems and instrumentation and controls are described, and operational procedures, system limitations, and maintenance philosophy are discussed.« less

Healthcare utilization in adults with opioid dependence receiving extended release naltrexone compared to treatment as usual.

PubMed

Soares, William E; Wilson, Donna; Rathlev, Niels; Lee, Joshua D; Gordon, Michael; Nunes, Edward V; O'Brien, Charles P; Friedmann, Peter D

2018-02-01

Opioid use disorders have reached epidemic proportions, with overdose now the leading cause of accidental death in the United States. Extended release naltrexone (XR-NTX) has emerged as a medication treatment that reduces opioid use and craving. However, the effect of XR-NTX therapy on acute healthcare utilization, including emergency department visits and inpatient hospitalizations, remains uncertain. The objective of the current study is to evaluate hospital-based healthcare resource utilization in adults involved in the criminal justice system with a history of opioid use disorder randomized to XR-NTX therapy compared with treatment as usual (TAU) during a 6-month treatment phase and 12months post-treatment follow up. This retrospective exploratory analysis uses data collected in a published randomized trial. Comparisons of the number of emergency department visits and hospital admissions (for drug detox, psychiatric care and other medical reasons) were performed using chi square tests for any admission and negative binomial models for number of admissions. Of the 308 participants randomized, 96% had utilization data (76% complete 6months, 67% complete follow up). No significant differences were seen in overall healthcare utilization (IRR=0.88, 95%CI 0.63-1.23, p=0.45), or substance use-related drug detox hospitalizations (IRR=0.83, 95%CI 0.32-2.16, p=0.71). Despite having more participants report chronic medical problems at baseline (43% vs. 32%, p=0.05), those receiving XR-NTX generally experienced equivalent or lower rates of healthcare utilization compared to TAU. The XR-NTX group had significantly lower medical/surgical related hospital admissions (IRR=0.55, 95%CI 0.30-1.00, p=0.05) during the course of the entire study. XR-NTX did not significantly increase rates of healthcare utilization compared to TAU. Provider concerns regarding healthcare utilization should not preclude the consideration of XR-NTX as therapy for opioid use disorders. Copyright © 2018 Elsevier Inc. All rights reserved.

Vision 20/20: Single photon counting x-ray detectors in medical imaging

PubMed Central

Taguchi, Katsuyuki; Iwanczyk, Jan S.

2013-01-01

Photon counting detectors (PCDs) with energy discrimination capabilities have been developed for medical x-ray computed tomography (CT) and x-ray (XR) imaging. Using detection mechanisms that are completely different from the current energy integrating detectors and measuring the material information of the object to be imaged, these PCDs have the potential not only to improve the current CT and XR images, such as dose reduction, but also to open revolutionary novel applications such as molecular CT and XR imaging. The performance of PCDs is not flawless, however, and it seems extremely challenging to develop PCDs with close to ideal characteristics. In this paper, the authors offer our vision for the future of PCD-CT and PCD-XR with the review of the current status and the prediction of (1) detector technologies, (2) imaging technologies, (3) system technologies, and (4) potential clinical benefits with PCDs. PMID:24089889

Optimized extraction by cetyl trimethyl ammonium bromide reversed micelles of xylose reductase and xylitol dehydrogenase from Candida guilliermondii homogenate.

PubMed

Cortez, Ely Vieira; Pessoa, Adalberto; das Graças de Almeida Felipe, Maria; Roberto, Inês Conceição; Vitolo, Michele

2004-07-25

The intracellular enzymes xylose reductase (XR, EC 1.1.1.21) and xylitol dehydrogenase (XD, EC 1.1.1.9) from Candida guilliermondii, grown in sugar cane bagasse hydrolysate, were separated by reversed micelles of cetyl trimethyl ammonium bromide (CTAB) cationic surfactant. An experimental design was employed to optimize the extraction conditions of both enzymes. Under these conditions (temperature = 5 degree C, hexanol: isooctane proportion = 5% (v/v), 22 %, surfactant concentration = 0.15M, pH = 7.0 and electrical conductivity = 14 mScm(-1)) recovery values of about 100 and 80% were achieved for the enzymes XR and XD, respectively. The purity of XR and XD increased 5.6- and 1.8-fold, respectively. The extraction process caused some structural modifications in the enzymes molecules, as evidenced by the alteration of K(M) values determined before and after extraction, either in regard to the substrate (up 35% for XR and down 48% for XD) or cofactor (down 29% for XR and up 11% for XD). However, the average variation of V(max) values for both enzymes was not higher than 7%, indicating that the modified affinity of enzymes for their respective substrates and cofactors, as consequence of structural modifications suffered by them during the extraction, are compensated in some extension. This study demonstrated that liquid-liquid extraction by CTAB reversed micelles is an efficient process to separate the enzymes XR and XD present in the cell extract, and simultaneously increase the enzymatic activity and the purity of both enzymes produced by C. guilliermondii.

Nanoscale structure of the oil-water interface

DOE PAGES

Fukuto, M.; Ocko, B. M.; Bonthuis, D. J.; ...

2016-12-15

X-ray reflectivity (XR) and atomistic molecular dynamics (MD) simulations, carried out to determine the structure of the oil-water interface, provide new insight into the simplest liquid-liquid interface. For several oils (hexane, dodecane, and hexadecane) the XR shows very good agreement with a monotonic interface-normal electron density profile (EDP) broadened only by capillary waves. Similar agreement is also found for an EDP including a sub-Å thick electron depletion layer separating the oil and the water. As a result, the XR and MD derived depletions are much smaller than reported for the interface between solid-supported hydrophobic monolayers and water.

Micro and Macro Mechanics of Fracture in Ceramics.

DTIC Science & Technology

1982-10-30

XrP /Kc)21 (2.2) The validity of Eq. (2.2) has been tested with Vickers indentation in a wide range of ceramic materials (Anstis et al. 1981). J6...basis that the replacement of Kr in Eq. (2.1) with any function of the form Kr - XrP /cn (n > 0) yields a set of equations of the same form as (2.2) to...superposition of two components, one due to the residual stress (Eqn. 8) and the other due to the applied load (Eqn. 2) -272- K XrP /C 3/2 + G(7SIc)1/2

Extended-Release Naltrexone: A Qualitative Analysis of Barriers to Routine Use.

PubMed

Alanis-Hirsch, Kelly; Croff, Raina; Ford, James H; Johnson, Kim; Chalk, Mady; Schmidt, Laura; McCarty, Dennis

2016-03-01

The Medication Research Partnership (a national health plan and nine addiction treatment centers contracted with the health plan) sought to facilitate the adoption of pharmacotherapy for alcohol and opioid use disorders. Qualitative analysis of interviews with treatment center change leaders, individuals working for the manufacturer and its technical assistance contractor, and health plan managers extracted details on the processes used to order, store, bill for, and administer extended-release naltrexone. Qualitative themes were categorized using domains from the Consolidated Framework for Implementation Research (intervention characteristics, outer setting, inner setting, and provider characteristics). Characteristics of XR-NTX that inhibited use included the complexity of ordering and using the medication; cost was also a barrier. Outer setting barriers reflected patient needs and external health plan policies on formulary coverage, benefit management, and reimbursement. Program structures, the lack of physician linkages, a culture resistant to the use of medication, and unease with change were inner setting elements that limited use of XR-NTX. Patient stereotypes and a lack of knowledge about XR-NTX affected practitioner willingness to treat patients and prescribe XR-NTX. The Consolidated Framework for Implementation Research provided a useful lens to understand and interpret the processes affecting access to XR-NTX. Copyright © 2015 Elsevier Inc. All rights reserved.

CORROSION STUDIES FOR A FUSED SALT-LIQUID METAL EXTRACTION PROCESS FOR THE LIQUID METAL FUEL REACTOR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Susskind, H.; Hill, F.B.; Green, L.

1960-06-30

Corrosion screening tests were carried out on potential materials of construction for use in a fused salt-liquid metal extraction process plant. The corrodents of interest were NaCl--KCl-- MgCl/sub 2/ eutectic, LiCl--KCl eutectic, Bi-- U fuel, and BiCl/sub 3/, either separately or in various combinations. Screening tests to determine the resistance of a wide range of commercial alloys to the corrodents were performed in static and tilting-furnace capsules. Some ceramic materials were tested in static capsules. Largerscale tests of metallic materials were conducted in thermal convection loops and in a forced circulation loop. Some of the tests were conducted isothermally atmore » 500 deg C, and others were performed under 40 to 50 deg C temperature differences at roughly the same teinperature level. On the basis of metallographic examination of exposed test tabs and chemical analyses of corrodents, it was found that the binary and ternary eutectics by themselves produced little attack on any of the materials tested. A wide variety of materials including 1020 mild steel, 2 1/4 Cr--1 Mo alloy steel, types 304 (ELC), 310, 316, 347, 430, and 446 stainless steel, 16-1 Croloy, Inconel, Hastelloy C, Inor-8, Mo, and Ta is, therefore, available for further study. Corrosion by the ternary salt-fuel system was characteristic of that produced by the fuel alone. Alloys such as 1020 mild steel, and 1 1/4 Cr--1/ 2 Mo, and 2 1/4 Cr--1 Mo alloy steel, which are resistant to fuel, would be likely choices at present for container materials. BiCl/sub 3/ produced extensive attack on ternary salt-fuel containers when the fuel contained insufficient concentrations of oxidizable solutes. Au and Al/sub 2/O/sub 3/ were the only materials not attacked by BiCl/sub 3/ in ternary salt alone. (auth)« less

Use of Less Reactive Materials and More Stable Gases to Reduce Corrosive Wear When Lubricating with Halogenated Gases

NASA Technical Reports Server (NTRS)

Buckley, Donald H.; Johnson, Robert L.

1960-01-01

The gases CF2Cl-CF2Cl, CF2Cl2, and CF2Br-CF2Br were used to lubricate metals, cermets, and ceramics in this study. One of the criteria for determining the effectiveness of a reactive-gas-lubricated systems is the stability of the halogen-containing gas molecule. The carbon-to-halogen bond in the ethane molecule has extremely good thermal stability superior to the methane analogs (CF2Cl2 and CF2Br2) used in earlier research. For this reason, the ethane compounds CF2Cl-CF2Cl and CF2Br-CF2Br were considered as high-temperature lubricants. Friction and wear studies were made with a hemisphere (3/16-in. rad.) rider sliding in a circumferential path on the flat surface of a rotating disk (21/2-in. diam. ). The specimens of metal alloys, cermets, and ceramics were run In an atmosphere of the various gases with a load of 1200 grams, sliding velocities from 75 to 8000 feet per minute, and temperatures from 75 to 1400 F. The gas CF2Cl-CF2Cl was found to be an effective lubricant for the cermet LT-LB (59.0 Cr, 19.0 Al2O3, 20.0 Mo, 2.0 Ti) and the ceramic Al2O3 sliding on Stellite Star J (cobalt-base alloy) at temperatures to 1400 F. The bromine-containing gas CF2Br-CF2Br was found to give friction and wear values that can be considered to be in a region of effective boundary lubrication for the cermet K175D (nickel-bonded metal carbide) sliding on the metal Hastelloy R-235 (nickel-base alloy) at temperatures to 1200 F.

Corrosion study of a highly durable electrolyzer based on cold crucible technique for pyrochemical reprocessing of spent nuclear oxide fuel

NASA Astrophysics Data System (ADS)

Takeuchi, M.; Arai, Y.; Kase, T.; Nakajima, Y.

2013-01-01

The application of the cold crucible technique to a pyrochemical electrolyzer used in the oxide-electrowinning method, which is a method for the pyrochemical reprocessing of spent nuclear oxide fuel, is proposed as a means for improving corrosion resistance. The electrolyzer suffers from a severe corrosion environment consisting of molten salt and corrosive gas. In this study, corrosion tests for several metals in molten 2CsCl-NaCl at 923 K with purging chlorine gas were conducted under controlled material temperature conditions. The results revealed that the corrosion rates of several materials were significantly decreased by the material cooling effect. In particular, Hastelloy C-22 showed excellent corrosion resistance with a corrosion rate of just under 0.01 mm/y in both molten salt and vapor phases by controlling the material surface at 473 K. Finally, an engineering-scale crucible composed of Hastelloy C-22 was manufactured to demonstrate the basic function of the cold crucible. The cold crucible induction melting system with the new concept Hastelloy crucible showed good compatibility with respect to its heating and cooling performances.

Medication adherence and symptom reduction in adults treated with mixed amphetamine salts in a randomized crossover study.

PubMed

Adler, Lenard A; Lynch, Lauren R; Shaw, David M; Wallace, Samantha P; Ciranni, Michael A; Briggie, Alexis M; Kulaga, Agatha; O'Donnell, Katherine E; Faraone, Stephen V

2011-09-01

The study objectives were to 1) evaluate medication adherence for adults with attention-deficit/hyperactivity disorder (ADHD) treated with 3 times daily (TID) mixed amphetamine salts immediate release (MAS IR) versus once-daily (qAM) MAS extended release (MAS XR) in a randomized, crossover study; and 2) to examine the associations between adherence and efficacy for MAS IR and MAS XR. Sixty-two adults with ADHD were enrolled and 49 completed the study. The treatment condition order (TID-qAM or qAM-TID) was counterbalanced across participants, with an intervening washout period of ≥ 7 days. Adherence was assessed via 3 measures: 1) self-report, 2) pill count, and 3) the Medication Event Monitoring System (MEMS(®)). The primary efficacy measure was the ADHD Rating Scale (ADHD-RS); secondary measures included the Time-Sensitive ADHD Symptom Scale (TASS) and Clinical Global Impressions-Severity of Illness (CGI-S) scale. Adherence to treatment as measured by self-report and pill count was not significantly different between MAS XR and MAS IR. Adherence was significantly better for MAS XR than MAS IR for all of the MEMS(®) measures. The mean change in ADHD-RS, TASS, and CGI-S scores at endpoint was significantly improved for both MAS IR and MAS XR and did not differ significantly between groups. There was not a significant adherence by efficacy interaction. Adults with ADHD adhered equally well with MAS IR as with MAS XR when assessed by pill count and self-report, but not by the MEMS(®) measures. Both treatments significantly reduced ADHD symptoms, and efficacy was not significantly different between groups. Adherence was not associated with treatment outcome.

Heteromeric assembly of P2X subunits

PubMed Central

Saul, Anika; Hausmann, Ralf; Kless, Achim; Nicke, Annette

2013-01-01

Transcripts and/or proteins of P2X receptor (P2XR) subunits have been found in virtually all mammalian tissues. Generally more than one of the seven known P2X subunits have been identified in a given cell type. Six of the seven cloned P2X subunits can efficiently form functional homotrimeric ion channels in recombinant expression systems. This is in contrast to other ligand-gated ion channel families, such as the Cys-loop or glutamate receptors, where homomeric assemblies seem to represent the exception rather than the rule. P2XR mediated responses recorded from native tissues rarely match exactly the biophysical and pharmacological properties of heterologously expressed homomeric P2XRs. Heterotrimerization of P2X subunits is likely to account for this observed diversity. While the existence of heterotrimeric P2X2/3Rs and their role in physiological processes is well established, the composition of most other P2XR heteromers and/or the interplay between distinct trimeric receptor complexes in native tissues is not clear. After a description of P2XR assembly and the structure of the intersubunit ATP-binding site, this review summarizes the distribution of P2XR subunits in selected mammalian cell types and the biochemically and/or functionally characterized heteromeric P2XRs that have been observed upon heterologous co-expression of P2XR subunits. We further provide examples where the postulated heteromeric P2XRs have been suggested to occur in native tissues and an overview of the currently available pharmacological tools that have been used to discriminate between homo- and heteromeric P2XRs. PMID:24391538

Insight and Treatment Outcomes in Schizophrenia: Post-hoc Analysis of a Long-term, Double-blind Study Comparing Lurasidone and Quetiapine XR.

PubMed

Harvey, Philip D; Siu, Cynthia O; Loebel, Antony D

2017-12-01

Objective: The objective of this post-hoc analysis was to evaluate the effect of lurasidone and quetiapine extended-release (XR) on insight and judgment and assess the longitudinal relationships between improvement in insight and cognitive performance, functional capacity, quality of well-being, and depressive symptoms in patients with schizophrenia. Design: Clinically unstable patients with schizophrenia (N=488) were randomized to once-daily, fixed-dose treatment with lurasidone 80mg, lurasidone 160mg, quetiapine XR 600mg, or placebo, followed by a long-term, double-blind, flexible-dose continuation study involving these agents. Results: Significantly greater improvement in insight and judgment (assessed by the Positive and Negative Syndrome Scale G12 item) for the lurasidone and quetiapine XR groups, compared to the placebo group, was observed at Week 6. Over a subsequent six-month continuation period, the flexible dose lurasidone group showed significantly greater improvement in insight from acute phase baseline compared to the flexible-dose quetiapine XR group (QXR-QXR) (p=0.032). Improvement in insight was significantly correlated with improvement in cognition ( p =0.014), functional capacity (p=0.006, UPSA-B), quality of well-being ( p =0.033, QWB), and depressive symptoms ( p =0.05, Montgomery-Åsberg Depression Rating Scale [MADRS] score) across treatment groups and study periods. Conclusion: In this post-hoc analysis, flexibly dosed lurasidone 40 to 160mg/d was found to be associated with significantly greater improvement in insight compared to flexibly dosed quetiapine XR 200 to 800mg/d over long-term treatment in patients with schizophrenia. Across treatment groups, improvement in insight and judgment was significantly associated with improvement in cognition, functional capacity, quality of well-being, and depressive symptoms over time.

Harm reduction with pharmacotherapy for homeless people with alcohol dependence: Protocol for a randomized controlled trial

PubMed Central

Collins, Susan E.; Saxon, Andrew J.; Duncan, Mark H.; Smart, Brian F.; Merrill, Joseph O.; Malone, Daniel K.; Jackson, T. Ron; Clifasefi, Seema L.; Joesch, Jutta; Ries, Richard K.

2014-01-01

Background Interventions requiring abstinence from alcohol are neither preferred by nor shown to be highly effective with many homeless individuals with alcohol dependence. It is therefore important to develop lower-threshold, patient-centered interventions for this multimorbid and high-utilizing population. Harm-reduction counseling requires neither abstinence nor use reduction and pairs a compassionate style with patient-driven goal-setting. Extended-release naltrexone (XR-NTX), a monthly injectable formulation of an opioid receptor antagonist, reduces craving and may support achievement of harm-reduction goals. Together, harm-reduction counseling and XR-NTX may support alcohol harm reduction and quality-of-life improvement. Aims Study aims include testing: a) the relative efficacy of XR-NTX and harm-reduction counseling compared to a community-based, supportive-services-as-usual control, b) theory-based mediators of treatment effects, and c) treatment effects on publicly funded service costs. Methods This RCT involves four arms: a) XR-NTX+harm-reduction counseling, b) placebo+harm-reduction counseling, c) harm-reduction counseling only, and d) community-based, supportive-services-as-usual control conditions. Participants are currently/formerly homeless, alcohol dependent individuals (N=300). Outcomes include alcohol variables (i.e., craving, quantity/frequency, problems and biomarkers), health-related quality of life, and publicly funded service utilization and associated costs. Mediators include 10-point motivation rulers and the Penn Alcohol Craving Scale. XR-NTX and harm-reduction counseling are administered every 4 weeks over the 12-week treatment course. Follow-up assessments are conducted at weeks 24 and 36. Discussion If found efficacious, XR-NTX and harm-reduction counseling will be well-positioned to support reductions in alcohol-related harm, decreases in costs associated with publicly funded service utilization, and increases in quality of life among homeless, alcohol-dependent individuals. PMID:24846619

Bioequivalence of Dapagliflozin/Metformin Extended-release Fixed-combination Drug Product and Single-component Dapagliflozin and Metformin Extended-release Tablets in Healthy Russian Subjects.

PubMed

Khomitskaya, Yunona; Tikhonova, Nadezhda; Gudkov, Konstantin; Erofeeva, Svetlana; Holmes, Victoria; Dayton, Brian; Davies, Nigel; Boulton, David W; Tang, Weifeng

2018-04-01

Fixed-combination drug products (FCDPs) combining dapagliflozin and metformin extended release (XR) may provide patients with type 2 diabetes mellitus with an alternative antihyperglycemic treatment, which could improve adherence by reducing tablet burden. This study evaluated the bioequivalence of dapagliflozin/metformin XR FCDP versus the co-administration of the individual monotherapy tablets currently available for use in the Russian Federation. Healthy subjects aged 18 to 45 years were enrolled in this randomized, open-label, 2-period crossover study, conducted in a single Russian center. Pharmacokinetic parameters (AUC 0-t , C max , and C max /AUC 0-t ) were used to assess bioequivalence of dapagliflozin/metformin XR (10/1000 mg) FCDP to the individual component tablets (dapagliflozin [10 mg] plus metformin XR [2 × 500 mg]) under standard fed conditions. Safety and tolerability were also assessed. Forty healthy subjects were included (47.5% male; mean age, 30 years; and mean body mass index, 24.2 kg/m 2 ). Dapagliflozin and metformin XR in the FCDP were bioequivalent to the individual component tablets marketed in the Russian Federation, with the 90% CIs of the geometric least-squares mean ratios for all key pharmacokinetic parameters being contained within the 80% to 125% bioequivalence limits. Both FCDP and the individual component formulations were well tolerated, with no serious adverse events. Bioequivalence of dapagliflozin/metformin XR FCDP and the individual components was established without any new safety concerns, presenting a safe alternative for patients currently receiving regimens including each component individually. ClinicalTrials.gov identifier: NCT02722239. Copyright © 2018 Elsevier HS Journals, Inc. All rights reserved.

Harm reduction with pharmacotherapy for homeless people with alcohol dependence: protocol for a randomized controlled trial.

PubMed

Collins, Susan E; Saxon, Andrew J; Duncan, Mark H; Smart, Brian F; Merrill, Joseph O; Malone, Daniel K; Jackson, T Ron; Clifasefi, Seema L; Joesch, Jutta; Ries, Richard K

2014-07-01

Interventions requiring abstinence from alcohol are neither preferred by nor shown to be highly effective with many homeless individuals with alcohol dependence. It is therefore important to develop lower-threshold, patient-centered interventions for this multimorbid and high-utilizing population. Harm-reduction counseling requires neither abstinence nor use reduction and pairs a compassionate style with patient-driven goal-setting. Extended-release naltrexone (XR-NTX), a monthly injectable formulation of an opioid receptor antagonist, reduces craving and may support achievement of harm-reduction goals. Together, harm-reduction counseling and XR-NTX may support alcohol harm reduction and quality-of-life improvement. Study aims include testing: a) the relative efficacy of XR-NTX and harm-reduction counseling compared to a community-based, supportive-services-as-usual control, b) theory-based mediators of treatment effects, and c) treatment effects on publicly funded service costs. This RCT involves four arms: a) XR-NTX+harm-reduction counseling, b) placebo+harm-reduction counseling, c) harm-reduction counseling only, and d) community-based, supportive-services-as-usual control conditions. Participants are currently/formerly homeless, alcohol dependent individuals (N=300). Outcomes include alcohol variables (i.e., craving, quantity/frequency, problems and biomarkers), health-related quality of life, and publicly funded service utilization and associated costs. Mediators include 10-point motivation rulers and the Penn Alcohol Craving Scale. XR-NTX and harm-reduction counseling are administered every 4weeks over the 12-week treatment course. Follow-up assessments are conducted at weeks 24 and 36. If found efficacious, XR-NTX and harm-reduction counseling will be well-positioned to support reductions in alcohol-related harm, decreases in costs associated with publicly funded service utilization, and increases in quality of life among homeless, alcohol-dependent individuals. Copyright © 2014 Elsevier Inc. All rights reserved.

EliXR-TIME: A Temporal Knowledge Representation for Clinical Research Eligibility Criteria.

PubMed

Boland, Mary Regina; Tu, Samson W; Carini, Simona; Sim, Ida; Weng, Chunhua

2012-01-01

Effective clinical text processing requires accurate extraction and representation of temporal expressions. Multiple temporal information extraction models were developed but a similar need for extracting temporal expressions in eligibility criteria (e.g., for eligibility determination) remains. We identified the temporal knowledge representation requirements of eligibility criteria by reviewing 100 temporal criteria. We developed EliXR-TIME, a frame-based representation designed to support semantic annotation for temporal expressions in eligibility criteria by reusing applicable classes from well-known clinical temporal knowledge representations. We used EliXR-TIME to analyze a training set of 50 new temporal eligibility criteria. We evaluated EliXR-TIME using an additional random sample of 20 eligibility criteria with temporal expressions that have no overlap with the training data, yielding 92.7% (76 / 82) inter-coder agreement on sentence chunking and 72% (72 / 100) agreement on semantic annotation. We conclude that this knowledge representation can facilitate semantic annotation of the temporal expressions in eligibility criteria.

A girl with West syndrome and autistic features harboring a de novo TBL1XR1 mutation.

PubMed

Saitsu, Hirotomo; Tohyama, Jun; Walsh, Tom; Kato, Mitsuhiro; Kobayashi, Yu; Lee, Ming; Tsurusaki, Yoshinori; Miyake, Noriko; Goto, Yu-Ichi; Nishino, Ichizo; Ohtake, Akira; King, Mary-Claire; Matsumoto, Naomichi

2014-10-01

Recently, de novo mutations in TBL1XR1 were found in two patients with autism spectrum disorders. Here, we report on a Japanese girl presenting with West syndrome, Rett syndrome-like and autistic features. Her initial development was normal until she developed a series of spasms at 5 months of age. Electroencephalogram at 7 months showed a pattern of hypsarrhythmia, which led to a diagnosis of West syndrome. Stereotypic hand movements appeared at 8 months of age, and autistic features such as deficits in communication, hyperactivity and excitability were observed later, at 4 years and 9 months. Whole exome sequencing of the patient and her parents revealed a de novo TBL1XR1 mutation [c.209 G>A (p.Gly70Asp)] occurring at an evolutionarily conserved amino acid in an F-box-like domain. Our report expands the clinical spectrum of TBL1XR1 mutations to West syndrome with Rett-like features, together with autistic features.

Efficacy, Safety, and Tolerability of an Extended-Release Orally Disintegrating Methylphenidate Tablet in Children 6-12 Years of Age with Attention-Deficit/Hyperactivity Disorder in the Laboratory Classroom Setting.

PubMed

Childress, Ann C; Kollins, Scott H; Cutler, Andrew J; Marraffino, Andrea; Sikes, Carolyn R

2017-02-01

Methylphenidate extended-release orally disintegrating tablets (MPH XR-ODTs) represent a new technology for MPH delivery. ODTs disintegrate in the mouth without water and provide a pharmacokinetic profile that is consistent with once-daily dosing. This study sought to determine the efficacy, safety, and tolerability of this novel MPH XR-ODT formulation in school-age children with attention-deficit/hyperactivity disorder (ADHD) in a laboratory classroom setting. Children aged 6-12 years with ADHD (n = 87) were enrolled in this randomized, multicenter, double-blind, placebo-controlled, parallel, laboratory classroom study. The MPH XR-ODT dose was titrated to an optimized dose during a 4-week open-label period and maintained on that dose for 1 week. Participants (n = 85) were then randomized to receive their optimized dose of MPH XR-ODT or placebo once daily for 1 week (double blind), culminating in a laboratory classroom testing day. Efficacy was evaluated using the Swanson, Kotkin, Agler, M-Flynn, and Pelham (SKAMP) Attention, Deportment, and Combined scores along with Permanent Product Measure of Performance (PERMP; Attempted and Correct) assessments. Onset and duration of drug action were also evaluated as key secondary endpoints. Safety assessments included adverse events (AEs), physical examinations, electrocardiograms (ECGs), and the Columbia Suicide Severity Rating Scale (C-SSRS). The average SKAMP-Combined score on the classroom study day was significantly better for the MPH XR-ODT group (n = 43) than for the placebo group (n = 39; p < 0.0001). The effect was evident at 1 hour and lasted through 12 hours postdose. The average SKAMP-Attention, SKAMP-Deportment, PERMP-A, and PERMP-C scores were indicative of significantly greater ADHD symptom control for the MPH XR-ODT group. The most common AEs reported were decreased appetite, upper abdominal pain, headache, insomnia, upper respiratory tract infection, affect lability, irritability, cough, and vomiting. MPH XR-ODT was effective and well tolerated for the treatment of children with ADHD in a laboratory classroom setting. Clinical Trial Registry: NCT01835548 ( ClinicalTrials.gov ).

Testing a chemical series inspired by plant stress oxylipin signalling agents for herbicide safening activity

PubMed Central

Brazier‐Hicks, Melissa; Knight, Kathryn M; Sellars, Jonathan D

2018-01-01

Abstract BACKGROUND Herbicide safening in cereals is linked to a rapid xenobiotic response (XR), involving the induction of glutathione transferases (GSTs). The XR is also invoked by oxidized fatty acids (oxylipins) released during plant stress, suggesting a link between these signalling agents and safening. To examine this relationship, a series of compounds modelled on the oxylipins 12‐oxophytodienoic acid and phytoprostane 1, varying in lipophilicity and electrophilicity, were synthesized. Compounds were then tested for their ability to invoke the XR in Arabidopsis and protect rice seedlings exposed to the herbicide pretilachlor, as compared with the safener fenclorim. RESULTS Of the 21 compounds tested, three invoked the rapid GST induction associated with fenclorim. All compounds possessed two electrophilic carbon centres and a lipophilic group characteristic of both oxylipins and fenclorim. Minor effects observed in protecting rice seedlings from herbicide damage positively correlated with the XR, but did not provide functional safening. CONCLUSION The design of safeners based on the characteristics of oxylipins proved successful in deriving compounds that invoke a rapid XR in Arabidopsis but not in providing classical safening in a cereal. The results further support a link between safener and oxylipin signalling, but also highlight species‐dependent differences in the responses to these compounds. © 2018 The Authors. Pest Management Science published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry. PMID:29330904

Semi-simultaneous application of neutron and X-ray radiography in revealing the defects in an Al casting.

PubMed

Balaskó, M; Korösi, F; Szalay, Zs

2004-10-01

A semi-simultaneous application of neutron and X-ray radiography (NR, XR) respectively, was applied to an Al casting. The experiments were performed at the 10MW VVR-SM research reactor in Budapest (Hungary). The aim was to reveal, identify and parameterize the hidden defects in the Al casting. The joint application of NR and XR revealed hidden defects located in the Al casting. Image analysis of the NR and XR images unveiled a cone-like dimensionality of the defects. The spectral density analysis of the images showed a distinctly different character for the hidden defect region of Al casting in comparison with that of the defect-free one.

Aversion to injection limits acceptability of extended-release naltrexone among homeless, alcohol-dependent patients.

PubMed

Friedmann, Peter D; Mello, Dawn; Lonergan, Sean; Bourgault, Claire; O'Toole, Thomas P

2013-01-01

Ending homelessness is a major priority of the Department of Veteran Affairs (VA), and alcohol use can be a barrier to stable housing. Clinical trials suggest that depot extended-release naltrexone (XR-NTX) is efficacious in reducing alcohol consumption among alcohol-dependent subjects. An open-label, randomized pilot study sought to examine the feasibility and effectiveness of XR-NTX versus oral naltrexone to improve alcohol consumption and housing stability among homeless, alcohol-dependent veterans at the Providence Veteran Affairs Medical Center. Of 215 potential candidates approached over a 16-month recruitment period, only 15 agreed to consider study entry and 7 were randomized. The primary reasons given for refusal were not wanting an injection; fear of needles; and not wanting to change drinking habits. Only 1 participant in the XR-NTX group returned after the first injection. Three participants in the oral naltrexone group attended all 7 visits and had good outcomes. Although XR-NTX has demonstrated efficacy in reducing heavy drinking, limited acceptance of the injection might reduce its effectiveness among homeless, alcohol-dependent patients.

A double-blind, placebo-controlled, multicenter study with alprazolam and extended-release alprazolam in the treatment of panic disorder.

PubMed

Pecknold, J; Luthe, L; Munjack, D; Alexander, P

1994-10-01

This is a double-blind, placebo-controlled, flexible-dose, multicenter, 6-week study comparing regular alprazolam (compressed tablet, CT), given four times per day, and extended release alprazolam (XR), given once in the morning. The aim of the XR preparation is to offer less frequent dosing and to reduce interdose anxiety. Of the intent-to-treat group of 209 patients, 184 completed 3 weeks of medication and were evaluated according to protocol. There was a completer rate for the 6 weeks of 94% (CT), 97% (XR), and 87% (placebo). On global measures, Hamilton Rating Scale for Anxiety, phobia rating, and work disability measures, both active treatment groups were equally effective and significantly more efficacious than the placebo cell on endpoint MANOVA analysis. On analysis of the panic factor with endpoint data, both active treatment groups were equally effective throughout the 6-week trial and significantly more efficacious than the placebo group. Drowsiness occurred more frequently with CT alprazolam (86% of patients) than with the XR preparation (79%) or placebo (49%).

Adaptive response in human blood lymphocytes exposed to non-ionizing radiofrequency fields: resistance to ionizing radiation-induced damage.

PubMed

Sannino, Anna; Zeni, Olga; Romeo, Stefania; Massa, Rita; Gialanella, Giancarlo; Grossi, Gianfranco; Manti, Lorenzo; Vijayalaxmi; Scarfì, Maria Rosaria

2014-03-01

The aim of this preliminary investigation was to assess whether human peripheral blood lymphocytes which have been pre-exposed to non-ionizing radiofrequency fields exhibit an adaptive response (AR) by resisting the induction of genetic damage from subsequent exposure to ionizing radiation. Peripheral blood lymphocytes from four healthy donors were stimulated with phytohemagglutinin for 24 h and then exposed for 20 h to 1950 MHz radiofrequency fields (RF, adaptive dose, AD) at an average specific absorption rate of 0.3 W/kg. At 48 h, the cells were subjected to a challenge dose (CD) of 1.0 or 1.5 Gy X-irradiation (XR, challenge dose, CD). After a 72 h total culture period, cells were collected to examine the incidence of micronuclei (MN). There was a significant decrease in the number of MN in lymphocytes exposed to RF + XR (AD + CD) as compared with those subjected to XR alone (CD). These observations thus suggested a RF-induced AR and induction of resistance to subsequent damage from XR. There was variability between the donors in RF-induced AR. The data reported in our earlier investigations also indicated a similar induction of AR in human blood lymphocytes that had been pre-exposed to RF (AD) and subsequently treated with a chemical mutagen, mitomycin C (CD). Since XR and mitomycin-C induce different kinds of lesions in cellular DNA, further studies are required to understand the mechanism(s) involved in the RF-induced adaptive response.

Adaptive response in human blood lymphocytes exposed to non-ionizing radiofrequency fields: resistance to ionizing radiation-induced damage

PubMed Central

Sannino, Anna; Zeni, Olga; Romeo, Stefania; Massa, Rita; Gialanella, Giancarlo; Grossi, Gianfranco; Manti, Lorenzo; Vijayalaxmi; Scarfì, Maria Rosaria

2014-01-01

The aim of this preliminary investigation was to assess whether human peripheral blood lymphocytes which have been pre-exposed to non-ionizing radiofrequency fields exhibit an adaptive response (AR) by resisting the induction of genetic damage from subsequent exposure to ionizing radiation. Peripheral blood lymphocytes from four healthy donors were stimulated with phytohemagglutinin for 24 h and then exposed for 20 h to 1950 MHz radiofrequency fields (RF, adaptive dose, AD) at an average specific absorption rate of 0.3 W/kg. At 48 h, the cells were subjected to a challenge dose (CD) of 1.0 or 1.5 Gy X-irradiation (XR, challenge dose, CD). After a 72 h total culture period, cells were collected to examine the incidence of micronuclei (MN). There was a significant decrease in the number of MN in lymphocytes exposed to RF + XR (AD + CD) as compared with those subjected to XR alone (CD). These observations thus suggested a RF-induced AR and induction of resistance to subsequent damage from XR. There was variability between the donors in RF-induced AR. The data reported in our earlier investigations also indicated a similar induction of AR in human blood lymphocytes that had been pre-exposed to RF (AD) and subsequently treated with a chemical mutagen, mitomycin C (CD). Since XR and mitomycin-C induce different kinds of lesions in cellular DNA, further studies are required to understand the mechanism(s) involved in the RF-induced adaptive response. PMID:23979077

Patient preferences and extended-release naltrexone: A new opportunity to treat opioid use disorders in Ukraine.

PubMed

Marcus, Ruthanne; Makarenko, Iuliia; Mazhnaya, Alyona; Zelenev, Alexei; Polonsky, Maxim; Madden, Lynn; Filippovych, Sergii; Dvoriak, Sergii; Springer, Sandra A; Altice, Frederick L

2017-10-01

Scaling up HIV prevention for people who inject drugs (PWID) using opioid agonist therapies (OAT) in Ukraine has been restricted by individual and structural factors. Extended-release naltrexone (XR-NTX), however, provides new opportunities for treating opioid use disorders (OUDs) in this region, where both HIV incidence and mortality continue to increase. Survey results from 1613 randomly selected PWID from 5 regions in Ukraine who were currently, previously or never on OAT were analyzed for their preference of pharmacological therapies for treating OUDs. For those preferring XR-NTX, independent correlates of their willingness to initiate XR-NTX were examined. Among the 1613 PWID, 449 (27.8%) were interested in initiating XR-NTX. Independent correlates associated with interest in XR-NTX included: being from Mykolaiv (AOR=3.7, 95% CI=2.3-6.1) or Dnipro (AOR=1.8, 95% CI=1.1-2.9); never having been on OAT (AOR=3.4, 95% CI=2.1-5.4); shorter-term injectors (AOR=0.9, 95% CI 0.9-0.98); and inversely for both positive (AOR=0.8, CI=0.8-0.9), and negative attitudes toward OAT (AOR=1.3, CI=1.2-1.4), respectively. In the context of Eastern Europe and Central Asia where HIV is concentrated in PWID and where HIV prevention with OAT is under-scaled, new options for treating OUDs are urgently needed. here suggest that XR-NTX could become an option for addiction treatment and HIV prevention especially for PWID who have shorter duration of injection and who harbor negative attitudes to OAT. Decision aids that inform patient preferences with accurate information about the various treatment options are likely to guide patients toward better, patient-centered treatments and improve treatment entry and retention. Copyright © 2017 Elsevier B.V. All rights reserved.

Pharmacokinetic comparison using two tablets of an evogliptin/metformin XR 2.5/500 mg fixed dose combination vs. 1 tablet each of evogliptin 5 mg and metformin XR 1,000 mg
.

PubMed

Yoon, Sumin; Rhee, Su-Jin; Park, Sang-In; Yoon, Seo Hyun; Cho, Joo-Youn; Jang, In-Jin; Lee, SeungHwan; Yu, Kyung-Sang

2017-06-01

The aim of this study was to compare the pharmacokinetic (PK) characteristics of evogliptin and metformin following the administration of 2 evogliptin/metformin extended-release (XR) 2.5/500 mg FDC tablets with the coadministration of separate evogliptin 5-mg and metformin XR 1,000-mg tablets (separate formulations). A randomized, two-period, two-sequence crossover study was conducted. Subjects were randomly assigned to receive 2 FDC tablets or the individual tablets, followed by a 14-day washout period and the administration of the alternate treatment. Blood samples were collected predose and up to 72 hours postdose for each period. PK parameters including C_max and AUC_last were calculated. The geometric mean ratios (GMRs) and the 90% confidence intervals (CIs) between FDC and the separate formulations were calculated for the C_max and AUC_last of evogliptin and metformin. 33 subjects completed the study. The GMR (90% CI) values of C_max and AUC_last for evogliptin were 1.011 (0.959 - 1.066) and 1.010 (0.977 - 1.043), respectively. The GMR (90% CI) values of C_max and AUC_last for metformin were 0.892 (0.827 - 0.963) and 0.893 (0.841 - 0.947), respectively. There was no significant difference between the FDC and separate formulations regarding the occurrence of adverse events. All drug-related adverse events were considered to be mild and resolved without any treatment. Two FDC tablets of evogliptin/metformin XR 2.5/500 mg showed a similar PK profile to the separate formulations of evogliptin 5 mg and metformin XR 1,000 mg. All of the 90% CIs of GMR satisfied the regulatory bioequivalence criteria of 0.800 - 1.250.
.

Gastric polyps diagnosed by double-contrast upper gastrointestinal barium X-ray radiography mostly arise from the Helicobacter pylori-negative stomach with low risk of gastric cancer in Japan.

PubMed

Takeuchi, Chihiro; Yamamichi, Nobutake; Shimamoto, Takeshi; Takahashi, Yu; Mitsushima, Toru; Koike, Kazuhiko

2017-03-01

Double-contrast upper gastrointestinal barium X-ray radiography (UGI-XR) is a method broadly used for gastric cancer screening in Japan. Gastric polyp is one of the most frequent findings detected by UGI-XR, but how to handle it remains controversial. Gastric polyps of the 17,264 generally healthy subjects in Japan who underwent UGI-XR or upper gastrointestinal endoscopy (UGI-ES) in 2010 were analyzed. Of the 6,433 UGI-XR examinees (3,405 men and 3,028 women, 47.4 ± 9.0 years old), gastric polyps were detected in 464 men (13.6 %) and 733 women (24.2 %) and were predominantly developed on the non-atrophic gastric mucosa (p < 0.0001). Multiple logistic regression analysis showed that the presence of gastric polyps has significant association with lower value of serum anti-Helicobacter pylori IgG titer, female gender, lighter smoking habit, older age, and normal range of body mass index (≥18.5 and <25), but not with drinking or serum pepsinogen I/II ratio. During the 3-year follow-up, gastric cancer occurred in 7 subjects (0.11 %), but none of them had gastric polyps at the beginning of the follow-up period. Of the 2,722 subjects with gastric polyps among the 10,831 UGI-ES examinees in the same period, 2,446 (89.9 %) had fundic, 267 (9.8 %) had hyperplastic, and 9 (0.3 %) had adenomatous/cancerous polyps. Gastric polyps diagnosed by UGI-XR predominantly arise on the Helicobacter pylori-negative gastric mucosa with a low risk of gastric cancer in Japan. In the prospective observation, none of the UGI-XR examinees with gastric polyps developed gastric cancer for at least 3 years subsequently.

Subcritical and supercritical water oxidation of CELSS model wastes

NASA Technical Reports Server (NTRS)

Takahashi, Y.; Wydeven, T.; Koo, C.

1989-01-01

A mixture of ammonium hydroxide with acetic acid and a slurry of human feces, urine, and wipes were used as CELSS model wastes to be wet-oxidized at temperatures from 250 to 500 C, i.e. below and above the critical point of water (374 C and 218 kg/sq cm or 21.4 MPa). The effects of oxidation temperature ( 250-500 C) and residence time (0-120 mn) on carbon and nitrogen and on metal corrosion from the reactor material were studied. Almost all of the organic matter in the model wastes was oxidized in the temperature range from 400 to 500 C, above the critical conditions for water. In contrast, only a small portion of the organic matter was oxidized at subcritical conditions. A substantial amount of nitrogen remained in solution in the form of ammonia at temperatures ranging from 350 to 450 C suggesting that, around 400 C, organic carbon is completely oxidized and most of the nitrogen is retained in solution. The Hastelloy C-276 alloy reactor corroded during subcritical and supercritical water oxidation.

2G HTS wires made on 30 μm thick Hastelloy substrate

NASA Astrophysics Data System (ADS)

Sundaram, A.; Zhang, Y.; Knoll, A. R.; Abraimov, D.; Brownsey, P.; Kasahara, M.; Carota, G. M.; Nakasaki, R.; Cameron, J. B.; Schwab, G.; Hope, L. V.; Schmidt, R. M.; Kuraseko, H.; Fukushima, T.; Hazelton, D. W.

2016-10-01

REBCO (RE = rare earth) based high temperature superconducting (HTS) wires are now being utilized for the development of electric and electromagnetic devices for various industrial, scientific and medical applications. In the last several years, the increasing efforts in using the so-called second generation (2G) HTS wires for some of the applications require a further increase in their engineering current density (J e). The applications are those typically related to high magnetic fields where the higher J e of a REBCO wire, in addition to its higher irreversibility fields and higher mechanical strength, is already a major advantage over other superconducting wires. An effective way to increase the J e is to decrease the total thickness of a wire, for which using a thinner substrate becomes an obvious and attractive approach. By using our IBAD-MOCVD (ion beam assisted deposition-metal organic chemical vapor deposition) technology we have successfully made 2G HTS wires using a Hastelloy® C276 substrate that is only 30 μm in thickness. By using this thinner substrate instead of the typical 50 μm thick substrate and with a same critical current (I c), the J e of a wire can be increased by 30% to 45% depending on the copper stabilizer thickness. In this paper, we report the fabrication and characterization of the 2G HTS wires made on the 30 μm thick Hastelloy® C276 substrate. It was shown that with the optimization in the processing protocol, the surface of the thinner Hastelloy® C276 substrate can be readily electropolished to the quality needed for the deposition of the buffer stack. Same in the architecture as that on the standard 50 μm thick substrate, the buffer stack made on the 30 μm thick substrate showed an in-plane texture with a Δϕ of around 6.7° in the LaMnO3 cap layer. Low-temperature in-field transport measurement results suggest that the wires on the thinner substrate had achieved equivalent superconducting performance, most importantly the I c, as those on the 50 μm thick substrate. It is expected the 2G HTS wires made on the 30 μm thick Hastelloy® C276 substrate, the thinnest and with the highest J e to date, will greatly benefit such applications as high field magnets and high current cables.

Evaluation of a Brayton cycle recuperator after 21,000 hours of ground testing

NASA Technical Reports Server (NTRS)

Moore, T. J.

1979-01-01

A metallographic examination was conducted on a Brayton cycle recuperator and associated ducting after 21,000 hours of ground testing in air. At the hot (turbine) end, the recuperator operated at a nominal temperature of 675 C. The type 347 stainless-steel recuperator performed satisfactorily in the ground test even though the primary working fluid leaked to the atmosphere periodically. The leakage path was located at plate-bar braze joints which cracked as a result of thermal stresses. The welded type 347 stainless steel ducting a type 347/Hastelloy X bellows survived the ground test with no apparent loss of ductility or integrity. Some apparent aging embrittlement was observed in the Hastelloy X ducting but the serviceability was not affected.

Fracture mechanics criteria for turbine engine hot section components

NASA Technical Reports Server (NTRS)

Meyers, G. J.

1982-01-01

The application of several fracture mechanics data correlation parameters to predicting the crack propagation life of turbine engine hot section components was evaluated. An engine survey was conducted to determine the locations where conventional fracture mechanics approaches may not be adequate to characterize cracking behavior. Both linear and nonlinear fracture mechanics analyses of a cracked annular combustor liner configuration were performed. Isothermal and variable temperature crack propagation tests were performed on Hastelloy X combustor liner material. The crack growth data was reduced using the stress intensity factor, the strain intensity factor, the J integral, crack opening displacement, and Tomkins' model. The parameter which showed the most effectiveness in correlation high temperature and variable temperature Hastelloy X crack growth data was crack opening displacement.

Physiological and subjective effects of acute intranasal methamphetamine during extended-release alprazolam maintenance

PubMed Central

Lile, Joshua A.; Stoops, William W.; Glaser, Paul E.A.; Hays, Lon R.; Rush, Craig R.

2015-01-01

Background Medications development for methamphetamine dependence is ongoing, but no widely accepted, effective pharmacotherapy has been identified. Previous studies have demonstrated neurobiological perturbations to central GABAA activity following chronic stimulant use, and that positive modulation of GABAA receptors attenuates the neurochemical and behavioral response to stimulant drugs such as methamphetamine. Therefore, GABAA modulators could be useful as pharmacotherapies for stimulant-use disorders. Methods This study tested the hypothesis that intranasal methamphetamine would be safe and well tolerated during maintenance on extended-release alprazolam (XR), and that the effects of methamphetamine would be attenuated. Eight non-treatment-seeking, stimulant-dependent individuals completed an inpatient experiment in which ascending doses of intranasal methamphetamine (0, 5, 10, 20 and 30 mg) were administered after four days of alprazolam XR maintenance (0 and 1 mg/day). Results Intranasal methamphetamine produced prototypical effects (e.g., increased positive subjective ratings and elevated cardiovascular signs). The combination of intranasal methamphetamine and alprazolam XR was safe and well tolerated. Alprazolam XR produced small, but orderly, reductions in some of the subjective effects of methamphetamine, and performance impairment. Conclusions The present results demonstrate that methamphetamine use during alprazolam XR treatment would not pose a significant safety risk. Given the potential of GABAA positive modulators to manage certain aspects of stimulant abuse and dependence (i.e., drug-induced seizures, anxiety and stress), but the relatively small impact on the acute abuse-related effects of methamphetamine observed here, additional research with GABAA positive modulators is warranted, but should consider their use as an adjunct component of combination behavioral and/or drug treatment. PMID:21737214

A randomized, double-blind, placebo-controlled trial of antidepressants in Parkinson disease

PubMed Central

McDermott, M.P.; Kurlan, R.; Lyness, J.M.; Como, P.G.; Pearson, N.; Factor, S.A.; Juncos, J.; Serrano Ramos, C.; Brodsky, M.; Manning, C.; Marsh, L.; Shulman, L.; Fernandez, H.H.; Black, K.J.; Panisset, M.; Christine, C.W.; Jiang, W.; Singer, C.; Horn, S.; Pfeiffer, R.; Rottenberg, D.; Slevin, J.; Elmer, L.; Press, D.; Hyson, H.C.; McDonald, W.; Richard, Irene; McDonald, William; McDermott, Michael; Como, Peter G.; Kurlan, Roger; Lyness, Jeffrey M.; Pearson, Nancy; Sommerfeld, Barbara; Deeley, Cheryl; de la Torre, Tania; Barnard, Michele; Wilson, April; Lincoln, Maryann; Damgaard, Paula; Gerstenhaber, Melissa; Dustin, Kelly; Zappala, Nancy; Swartz, Camille; Creech, Mary; Shipley, Elda; Blankenship, Samantha; Beland, Monica; Roth, Jessie; Burnette, Heather; Foxworth, Tamara; Quesada, Monica; Lloyd, Mary; Pfeiffer, Brenda; Hansen, Joy; Folie, Joy; Wagner, Renee; Spears, Julia; Taylor, Colleen; Brown, Rachel; Iguchi, Lisa; Lim, Chen; LaDonna, Kori; Megens, Julie; Menza, Matthew; Cummings, Jeffrey; Hamer, Robert; Shannon, Kathleen; Odenkirchen, Joanne; Conwit, Robin; Beck, Christopher; LaDonna, Donna; Bausch, Jan; Kim, Scott; Chismar, Ron; Quinn, Sinead; Bean, Steve; Daigneault, Susan; Lindsay, Patricia; Ross, Tori; Kompoliti, Katie

2012-01-01

Objective: To evaluate the efficacy and safety of a selective serotonin reuptake inhibitor (SSRI) and a serotonin and norepinephrine reuptake inhibitor (SNRI) in the treatment of depression in Parkinson disease (PD). Methods: A total of 115 subjects with PD were enrolled at 20 sites. Subjects were randomized to receive an SSRI (paroxetine; n = 42), an SNRI (venlafaxine extended release [XR]; n = 34), or placebo (n = 39). Subjects met DSM-IV criteria for a depressive disorder, or operationally defined subsyndromal depression, and scored >12 on the first 17 items of the Hamilton Rating Scale for Depression (HAM-D). Subjects were followed for 12 weeks (6-week dosage adjustment, 6-week maintenance). Maximum daily dosages were 40 mg for paroxetine and 225 mg for venlafaxine XR. The primary outcome measure was change in the HAM-D score from baseline to week 12. Results: Treatment effects (relative to placebo), expressed as mean 12-week reductions in HAM-D score, were 6.2 points (97.5% confidence interval [CI] 2.2 to 10.3, p = 0.0007) in the paroxetine group and 4.2 points (97.5% CI 0.1 to 8.4, p = 0.02) in the venlafaxine XR group. No treatment effects were seen on motor function. Conclusions: Both paroxetine and venlafaxine XR significantly improved depression in subjects with PD. Both medications were generally safe and well tolerated and did not worsen motor function. Classification of Evidence: This study provides Class I evidence that paroxetine and venlafaxine XR are effective in treating depression in patients with PD. PMID:22496199

Possible Evidence for an Event Horizon in Cyg XR-1

NASA Technical Reports Server (NTRS)

Dolan, Joseph F.; Fisher, Richard R. (Technical Monitor)

2001-01-01

The X-ray emitting component in the Cyg XR-1/HDE226868 system is a leading candidate for identification as a stellar-mass sized black hole. The positive identification of a black hole as predicted by general relativity requires the detection of an event horizon surrounding the point singularity. One signature of such an event horizon would be the existence of dying pulse trains emitted by material spiraling into the event horizon from the last stable orbit around the black hole. We observed the Cyg XR-1 system at three different epochs in a 1400 - 3000 A bandpass with 0.1 ms time resolution using the Hubble Space Telescope's High Speed Photometer. Repeated excursions of the detected flux by more than three standard deviations above the mean are present in the UV flux with FWHM 1 - 10 ms. If any of these excursions are pulses of radiation produced in the system (and not just stochastic variability associated with the Poisson distribution of detected photon arrival times), then this short a timescale requires that the pulses originate in the accretion disk around Cyg XR-1. Two series of pulses with characteristics similar to those expected from dying pulse trains were detected in three hours of observation.

Atrophic gastritis and enlarged gastric folds diagnosed by double-contrast upper gastrointestinal barium X-ray radiography are useful to predict future gastric cancer development based on the 3-year prospective observation.

PubMed

Yamamichi, Nobutake; Hirano, Chigaya; Ichinose, Masao; Takahashi, Yu; Minatsuki, Chihiro; Matsuda, Rie; Nakayama, Chiemi; Shimamoto, Takeshi; Kodashima, Shinya; Ono, Satoshi; Tsuji, Yosuke; Niimi, Keiko; Sakaguchi, Yoshiki; Kataoka, Yosuke; Saito, Itaru; Asada-Hirayama, Itsuko; Takeuchi, Chihiro; Yakabi, Seiichi; Kaikimoto, Hikaru; Matsumoto, Yuta; Yamaguchi, Daisuke; Kageyama-Yahara, Natsuko; Fujishiro, Mitsuhiro; Wada, Ryoichi; Mitsushima, Toru; Koike, Kazuhiko

2016-07-01

Double-contrast upper gastrointestinal barium X-ray radiography (UGI-XR) is the standard gastric cancer screening method in Japan. Atrophic gastritis and enlarged gastric folds are considered the two major features of Helicobacter pylori-induced chronic gastritis, but the clinical meaning of evaluating them by UGI-XR has not been elucidated. We analyzed healthy UGI-XR examinees without a history of gastrectomy, previous Helicobacter pylori eradication and usage of gastric acid suppressants. Of the 6433 subjects, 1936 (30.1 %) had atrophic gastritis and 1253 (19.5 %) had enlarged gastric folds. During the 3-year prospective observational follow-up, gastric cancer developed in seven subjects, six of whom (85.7 %) had atrophic gastritis with H. pylori infection and five of whom (71.4 %) had enlarged gastric folds with H. pylori infection. The Kaplan-Meier method with log-rank testing revealed that both UGI-XR-based atrophic gastritis (p = 0.0011) and enlarged gastric folds (p = 0.0003) are significant predictors for future gastric cancer incidence.

An experimental study of large-scale vortices over a blunt-faced flat plate in pulsating flow

NASA Astrophysics Data System (ADS)

Hwang, K. S.; Sung, H. J.; Hyun, J. M.

Laboratory measurements are made of flow over a blunt flat plate of finite thickness, which is placed in a pulsating free stream, U=Uo(1+Aocos 2πfpt). Low turbulence-intensity wind tunnel experiments are conducted in the ranges of Stp<=1.23 and Ao<=0.118 at ReH=560. Pulsation is generated by means of a woofer speaker. Variations of the time-mean reattachment length xR as functions of Stp and Ao are scrutinized by using the forward-time fraction and surface pressure distributions (Cp). The shedding frequency of large-scale vortices due to pulsation is measured. Flow visualizations depict the behavior of large-scale vortices. The results for non-pulsating flows (Ao=0) are consistent with the published data. In the lower range of Ao, as Stp increases, xR attains a minimum value at a particular pulsation frequency. For large Ao, the results show complicated behaviors of xR. For Stp>=0.80, changes in xR are insignificant as Ao increases. The shedding frequency of large-scale vortices is locked-in to the pulsation frequency. A vortex-pairing process takes place between two neighboring large-scale vortices in the separated shear layer.

The high-energy X-ray spectrum of Centaurus XR-3 observed from OSO 8

NASA Technical Reports Server (NTRS)

Dolan, J. F.; Crannell, C. J.; Dennis, B. R.; Frost, K. J.; Orwig, L. E.

1984-01-01

Observations of the X-ray binary Cen XR-3 in the 20-120 keV energy range by means of OSO 8's high energy X-ray spectrometer, during July 16-19, 1975, and July 5-14 and 28-29, 1978, indicate that the source was in a high luminosity state during 1975 and a low luminosity one in 1978. While mean orbital light curves appear similar in shape in both years, orbit-to-orbit intensity variations are noted. Spectral, luminosity, and the 4.84 sec modulation are characterized. Cen XR-3 may be a system in which mass transfer by Roche lobe overflow, and by accretion from a stellar wind, are both effective in the production of observable X-ray radiation.

Memantine-induced chorea and dystonia.

PubMed

Borges, Letizia Goncalves; Bonakdarpour, Borna

2017-04-01

Memantine is an uncompetitive N -methyl-d-aspartate receptor antagonist and probably also has an indirect dopaminergic action at high concentrations. We describe a person with Alzheimer's disease who developed chorea and dystonia after inadvertently doubling of her daily dose by taking extended-release (XR) memantine twice daily, rather than once daily (planned dose memantine XR, 21 mg once daily), after the drug was switched from immediate release (IR, 10 mg twice daily). Memantine is rarely associated with movement disorders, but this case emphasises the need for awareness of potential problems when switching from memantine IR to XR. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Energy dependent calibration of XR-QA2 radiochromic film with monochromatic and polychromatic x-ray beams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Di Lillo, F.; Mettivier, G., E-mail: mettivier@na.infn.it; Sarno, A.

2016-01-15

Purpose: This work investigates the energy response and dose-response curve determinations for XR-QA2 radiochromic film dosimetry system used for synchrotron radiation work and for quality assurance in diagnostic radiology, in the range of effective energies 18–46.5 keV. Methods: Pieces of XR-QA2 films were irradiated, in a plane transverse to the beam axis, with a monochromatic beam of energy in the range 18–40 keV at the ELETTRA synchrotron radiation facility (Trieste, Italy) and with a polychromatic beam from a laboratory x-ray tube operated at 80, 100, and 120 kV. The film calibration curve was expressed as air kerma (measured free-in-air withmore » an ionization chamber) versus the net optical reflectance change (netΔR) derived from the red channel of the RGB scanned film image. Four functional relationships (rational, linear exponential, power, and logarithm) were tested to evaluate the best curve for fitting the calibration data. The adequacy of the various fitting functions was tested by using the uncertainty analysis and by assessing the average of the absolute air kerma error calculated as the difference between calculated and delivered air kerma. The sensitivity of the film was evaluated as the ratio of the change in net reflectance to the corresponding air kerma. Results: The sensitivity of XR-QA2 films increased in the energy range 18–39 keV, with a maximum variation of about 170%, and decreased in the energy range 38–46.5 keV. The present results confirmed and extended previous findings by this and other groups, as regards the dose response of the radiochromic film XR-QA2 to monochromatic and polychromatic x-ray beams, respectively. Conclusions: The XR-QA2 radiochromic film response showed a strong dependence on beam energy for both monochromatic and polychromatic beams in the range of half value layer values from 0.55 to 6.1 mm Al and corresponding effective energies from 18 to 46.5 keV. In this range, the film response varied by 170%, from a minimum sensitivity of 0.0127 to a maximum sensitivity of 0.0219 at 10 mGy air kerma in air. The more suitable function for air kerma calibration of the XR-QA2 radiochromic film was the power function. A significant batch-to-batch variation, up to 55%, in film response at 120 kV (46.5 keV effective energy) was observed in comparison with published data.« less

Forecasting Three-Month Outcomes in a Laboratory School Comparison of Mixed Amphetamine Salts Extended Release (Adderall XR) and Atomoxetine (Strattera) in School-Aged Children with ADHD

ERIC Educational Resources Information Center

Faraone, Stephen V.; Wigal, Sharon B.; Hodgkins, Paul

2007-01-01

Objective: Compare observed and forecasted efficacy of mixed amphetamine salts extended release (MAS-XR; Adderall) with atomoxetine (Strattera) in ADHD children. Method: The authors analyze data from a randomized, double-blind, multicenter, parallel-group, forced-dose-escalation laboratory school study of children ages 6 to 12 with ADHD combined…

New mini dental implant attachments versus O-ring attachment after cyclic aging: Analysis of retention strength and gap space.

PubMed

Fatalla, Abdalbseet A; Song, Ke; Cao, Ying-Guang

2017-06-01

Overdenture as a treatment modality for both partially and fully edentulous patients is costeffective and less expensive. The purpose of the present study was to examine the newly fabricated attachments by comparing them with conventional O-ring attachment in vitro in terms of retention force and cyclic aging resistance. A total of 150 samples were prepared and divided into five groups according to the materials used (O-ring attachment, Deflex M10 XR, Deflex Classic SR, Deflex Acrilato FD, and flexible acrylic resin). The retention force of different attachments was measured by a mini dental implant after three subsequent aging (0, 63, and 126) cycles in the circumstances similar to the oral environment. The gap space between the head of the implant and the inner surface of the attachments was detected. Two-way analysis of variance (ANOVA) analysis with multiple comparisons test was applied for statistical analysis. The results showed that Deflex M10 XR had the highest retention force and the lowest gap space after cyclic aging; in addition, by comparing the relative force reduction, the lowest values were obtained in the O-ring attachment and the highest values in the flexible acrylic resin attachment. The retention force measured after cyclic aging for the Deflex M10 XR attachment was greatly improved when compared with the O-ring attachment and other types of attachment materials; in addition, the Deflex M10 XR attachment exhibited the minimum gap space between the inner surface and the mini dental implant head. In conclusion, Deflex M10 XR has the ability to withstand weathering conditions and retains its durable and retentive properties after aging when compared with other attachments.

Separate and Combined Effects of Naltrexone and Extended-Release Alprazolam on the Reinforcing, Subject-Rated, and Cardiovascular Effects of Methamphetamine

PubMed Central

Marks, Katherine R.; Lile, Joshua A.; Stoops, William W.; Glaser, Paul E.A.; Hays, Lon R.; Rush, Craig R.

2016-01-01

Opioid antagonists (e.g., naltrexone) and positive modulators of γ-aminobutyric acid type A (GABAA) receptors (e.g., alprazolam) each modestly attenuate the abuse-related effects of stimulants. A previous study demonstrated that acute pretreatment with the combination of naltrexone and alprazolam attenuated a greater number of the subject-rated effects of d-amphetamine than the constituent drugs alone. This study tested the hypothesis that maintenance on the combination of naltrexone and alprazolam XR would attenuate the reinforcing and “positive” subject-rated effects of methamphetamine to a greater extent than the constituent drugs alone. Eight non-treatment-seeking, stimulant-using individuals completed a placebo-controlled, crossover, double-blind inpatient protocol. Participants were maintained on naltrexone (0 and 50 mg), alprazolam XR (0 and 1 mg), and the combination of naltrexone and alprazolam XR (50 mg and 1 mg, respectively) for 6–7 days. Under each maintenance condition, participants sampled intranasal doses of methamphetamine (0, 10, and 30 mg), and were then offered the opportunity to work for the sampled dose on a modified progressive-ratio procedure. Subject-rated drug effect questionnaires, psychomotor, and physiology assessments were collected. Intranasal methamphetamine functioned as a reinforcer and produced prototypical stimulant-like “positive” subject-rated and physiological effects. Maintenance on naltrexone significantly decreased the reinforcing, but not subject-rated drug effects of 10 mg methamphetamine. Alprazolam XR and the combination of naltrexone and alprazolam XR did not impact methamphetamine self-administration or subject-rated drug effects. The results support the continued evaluation of naltrexone for methamphetamine dependence, as well as the identification of other drugs that enhance its ability to reduce drug-taking behavior. PMID:27043121

Physiological and subjective effects of acute intranasal methamphetamine during extended-release alprazolam maintenance.

PubMed

Lile, Joshua A; Stoops, William W; Glaser, Paul E A; Hays, Lon R; Rush, Craig R

2011-12-15

Medications development for methamphetamine dependence is ongoing, but no widely accepted, effective pharmacotherapy has been identified. Previous studies have demonstrated neurobiological perturbations to central GABA(A) activity following chronic stimulant use, and that positive modulation of GABA(A) receptors attenuates the neurochemical and behavioral response to stimulant drugs such as methamphetamine. Therefore, GABA(A) modulators could be useful as pharmacotherapies for stimulant-use disorders. This study tested the hypothesis that intranasal methamphetamine would be safe and well tolerated during maintenance on extended-release alprazolam (XR), and that the effects of methamphetamine would be attenuated. Eight non-treatment-seeking, stimulant-dependent individuals completed an inpatient experiment in which ascending doses of intranasal methamphetamine (0, 5, 10, 20 and 30 mg) were administered after four days of alprazolam XR maintenance (0 and 1mg/day). Intranasal methamphetamine produced prototypical effects (e.g., increased positive subjective ratings and elevated cardiovascular signs). The combination of intranasal methamphetamine and alprazolam XR was safe and well tolerated. Alprazolam XR produced small, but orderly, reductions in some of the subjective effects of methamphetamine, and performance impairment. The present results demonstrate that methamphetamine use during alprazolam XR treatment would not pose a significant safety risk. Given the potential of GABA(A) positive modulators to manage certain aspects of stimulant abuse and dependence (i.e., drug-induced seizures, anxiety and stress), but the relatively small impact on the acute abuse-related effects of methamphetamine observed here, additional research with GABA(A) positive modulators is warranted, but should consider their use as an adjunct component of combination behavioral and/or drug treatment. Copyright © 2011. Published by Elsevier Ireland Ltd.

Separate and Combined Effects of Naltrexone and Extended-Release Alprazolam on the Reinforcing, Subject-Rated, and Cardiovascular Effects of Methamphetamine.

PubMed

Marks, Katherine R; Lile, Joshua A; Stoops, William W; Glaser, Paul E A; Hays, Lon R; Rush, Craig R

2016-06-01

Opioid antagonists (eg, naltrexone) and positive modulators of γ-aminobutyric acid type A receptors (eg, alprazolam) each modestly attenuate the abuse-related effects of stimulants. A previous study demonstrated that acute pretreatment with the combination of naltrexone and alprazolam attenuated a greater number of the subject-rated effects of D-amphetamine than the constituent drugs alone. This study tested the hypothesis that maintenance on the combination of naltrexone and alprazolam XR would attenuate the reinforcing and "positive" subject-rated effects of methamphetamine to a greater extent than the constituent drugs alone.Eight non-treatment-seeking, stimulant-using individuals completed a placebo-controlled, crossover, double-blind inpatient protocol. Participants were maintained on naltrexone (0 and 50 mg), alprazolam XR (0 and 1 mg), and the combination of naltrexone and alprazolam XR (50 mg and 1 mg, respectively) for 6 to 7 days. Under each maintenance condition, participants sampled intranasal doses of methamphetamine (0, 10, and 30 mg), and were then offered the opportunity to work for the sampled dose on a modified progressive-ratio procedure. Subject-rated drug effect questionnaires, psychomotor, and physiology assessments were collected.Intranasal methamphetamine functioned as a reinforcer and produced prototypical stimulant-like "positive" subject-rated and physiological effects. Maintenance on naltrexone significantly decreased the reinforcing, but not subject-rated drug effects of 10-mg methamphetamine. Alprazolam XR and the combination of naltrexone and alprazolam XR did not impact methamphetamine self-administration or subject-rated drug effects. The results support the continued evaluation of naltrexone for methamphetamine dependence, as well as the identification of other drugs that enhance its ability to reduce drug-taking behavior.

A Randomized Double-blind, Placebo Controlled Trial of Venlafaxine-Extended Release for Co-occurring Cannabis Dependence and Depressive Disorders

PubMed Central

Levin, Frances R.; Mariani, John; Brooks, Daniel J.; Pavlicova, Martina; Nunes, Edward V.; Agosti, Vito; Bisaga, Adam; Sullivan, Maria A.; Carpenter, Kenneth M.

2013-01-01

Aim To evaluate whether venlafaxine-extended release (VEN-XR) is an effective treatment for cannabis dependence with concurrent depressive disorders. Design This was a randomized, 12 week, double-blind, placebo-controlled trial of outpatients (n = 103) with DSM-IV cannabis dependence and major depressive disorder or dysthymia. Participants received up to 375 mg VEN-XR on a fixed-flexible schedule or placebo. All patients received weekly individual cognitive-behavioral psychotherapy that primarily targeted marijuana use. Settings The trial was conducted at two university research centers in the United States. Participants One hundred and three cannabis dependent adults participated in the trial. Measurements The primary outcome measures were 1) abstinence from marijuana defined as at least two consecutive urine-confirmed abstinent weeks and 2) improvement in depressive symptoms based on the Hamilton Depression Rating Scale. Findings The proportion of patients achieving a clinically significant mood improvement [50% decrease in Hamilton Depression score from baseline] was high and did not differ between groups receiving VEN-XR (63%) and placebo (69%) (X12=0.48, p-value= 0.49). The proportion of patients achieving abstinence was low overall, but was significantly worse on VEN-XR (11.8%) compared to placebo (36.5%) (X12=7.46, p-value<0.01; OR = 4.51, 95% CI: 1.53, 13.3). Mood improvement was associated with reduction in marijuana use in the placebo group (F1,179=30.49, p-value<0.01), but not the VEN-XR group (F1,186=0.02, p-value=0.89). Conclusions For depressed, cannabis-dependent patients, venlafaxine-extended release does not appear to be effective at reducing depression and may lead to an increase in cannabis use. PMID:23297841

Tolerability of extended-release quetiapine fumarate compared with immediate-release quetiapine fumarate in older patients with Alzheimer's disease with symptoms of psychosis and/or agitation: a randomised, double-blind, parallel-group study.

PubMed

De Deyn, Peter Paul; Eriksson, Hans; Svensson, Hanna

2012-03-01

The objective of this study was to assess the safety and tolerability of extended-release quetiapine fumarate (quetiapine XR) compared with quetiapine immediate-release (quetiapine IR) in older patients with Alzheimer's disease with symptoms of psychosis and/or agitation. This was a 6-week, double-blind, double-dummy, randomised study. Of the 109 patients screened, 100 were randomised to receive quetiapine XR (n = 68) or quetiapine IR (n = 32), at doses of 50 and 25 mg/day, respectively. Treatment was escalated to 100 mg/day by Day 4. At Day 8, a flexible-dose (50-300 mg/day) period began when dose adjustment was made at the investigator's discretion. The primary variable was incidence and type of adverse events (AEs). Secondary variables included efficacy and other safety assessments. Mean daily doses were 143.6 and 142.0 mg in the quetiapine XR and quetiapine IR groups, respectively. Ninety patients completed the study; only one withdrew (in the quetiapine XR group) because of an AE. Laboratory evaluations identified severe neutropaenia (one patient), mild neutropaenia (three patients) and eosinophilia (five patients); however, these were not reported, as AEs and confounding factors, such as patient age, concomitant illness and medication, made it difficult to determine any relationship to quetiapine treatment. Numerical improvements from baseline were seen across both treatment groups in Neuropsychiatric Inventory frequency × severity total, Neuropsychiatric Inventory-Nursing Home version, Cohen-Mansfield Agitation Inventory, Clinical Global Impression-Severity of Illness and Clinical Global Impression-Improvement scores. Quetiapine XR dosed up to 300 mg/day was generally well tolerated, with a similar profile to that of quetiapine IR. Copyright © 2011 John Wiley & Sons, Ltd.

Opioid Challenge Evaluation of Blockade by Extended-Release Naltrexone in Opioid-Abusing Adults: Dose-Effects and Time-Course

PubMed Central

Bigelow, George E.; Preston, Kenzie L.; Schmittner, John; Dong, Qunming; Gastfriend, David R.

2013-01-01

Background Oral naltrexone's effectiveness as an opioid antagonist has been limited due to poor patient adherence. A long-acting naltrexone formulation may be beneficial. This study evaluated the effects of extended-release injectable naltrexone (XR-NTX), targeted for a one-month duration of action, in blocking opioid agonist challenge effects in humans. Methods Outpatient non-dependent opioid abusers (N=27) were randomly assigned to a single double-blind IM administration of 75, 150, or 300 mg XR-NTX. To assess the extent of opioid blockade, hydromorphone challenges (0, 3, 4.5, 6 mg IM in ascending order at 1-hr intervals [up to 13.5 mg total]) were given at pretreatment baseline and on days 7, 14, 21, 28, 42, and 56. Opioid blockade was assessed via (1) tolerability of the ascending hydromorphone doses; (2) Visual Analog Scale (VAS) ratings of subjective opioid effects and (3) pupil diameter. Effects on the VAS and pupils were assessed via the slope of the time-action function over ascending hydromorphone doses, with zero slope indicating complete blockade. Results Blockade of the VAS “any drug effect” response to 3 mg hydromorphone was complete for 14, 21, and 28 days, respectively, for the XR-NTX doses of 75, 150 and 300 mg. Subjective effects were more readily blocked than was pupil constriction. Higher hydromorphone doses produced only modest increases in agonist effects. With the 300 mg XR-NTX dose the slope of VAS responses remained at or near zero for one month even with maximal cumulative hydromorphone dosing. Conclusions These data quantify the month-long opioid blockade underlying XR-NTX's efficacy in opioid dependence treatment. PMID:22079773

Aging pathways for organophosphate-inhibited human butyrylcholinesterase, including novel pathways for isomalathion, resolved by mass spectrometry.

PubMed

Li, He; Schopfer, Lawrence M; Nachon, Florian; Froment, Marie-Thérèse; Masson, Patrick; Lockridge, Oksana

2007-11-01

Some organophosphorus compounds are toxic because they inhibit acetylcholinesterase (AChE) by phosphylation of the active site serine, forming a stable conjugate: Ser-O-P(O)-(Y)-(XR) (where X can be O, N, or S and Y can be methyl, OR, or SR). The inhibited enzyme can undergo an aging process, during which the X-R moiety is dealkylated by breaking either the P-X or the X-R bond depending on the specific compound, leading to a nonreactivatable enzyme. Aging mechanisms have been studied primarily using AChE. However, some recent studies have indicated that organophosphate-inhibited butyrylcholinesterase (BChE) may age through an alternative pathway. Our work utilized matrix-assisted laser desorption/ionization-time-of-flight mass spectrometry to study the aging mechanism of human BChE inhibited by dichlorvos, echothiophate, diisopropylfluorophosphate (DFP), isomalathion, soman, sarin, cyclohexyl sarin, VX, and VR. Inhibited BChE was aged in the presence of H2O18 to allow incorporation of (18)O, if cleavage was at the P-X bond. Tryptic-peptide organophosphate conjugates were identified through peptide mass mapping. Our results showed no aging of VX- and VR-treated BChE at 25 degrees C, pH 7.0. However, BChE inhibited by dichlorvos, echothiophate, DFP, soman, sarin, and cyclohexyl sarin aged exclusively through O-C bond cleavage, i.e., the classical X-R scission pathway. In contrast, isomalathion aged through both X-R and P-X pathways; the main aged product resulted from P-S bond cleavage and a minor product resulted from O-C and/or S-C bond cleavage.

Molecular simulation to investigate the cofactor specificity for pichia stipitis Xylose reductase.

PubMed

Xia, Xiao-Le; Cong, Shan; Weng, Xiao-Rong; Chen, Jin-Hua; Wang, Jing-Fang; Chou, Kuo-Chen

2013-11-01

Xylose is one of the most abundant carbohydrates in nature, and widely used to produce bioethanol via fermentation in industry. Xylulose can produce two key enzymes: xylose reductase and xylitol dehydrogenase. Owing to the disparate cofactor specificities of xylose reductase and xylitol dehydrogenase, intracellular redox imbalance is detected during the xylose fermentation, resulting in low ethanol yields. To overcome this barrier, a common strategy is applied to artificially modify the cofactor specificity of xylose reductase. In this study, we utilized molecular simulation approaches to construct a 3D (three-dimensional) structural model for the NADP-dependent Pichia stipitis xylose reductase (PsXR). Based on the 3D model, the favourable binding modes for both cofactors NAD and NADP were obtained using the flexible docking procedure and molecular dynamics simulation. Structural analysis of the favourable binding modes showed that the cofactor binding site of PsXR was composed of 3 major components: a hydrophilic pocket, a hydrophobic pocket as well as a linker channel between the aforementioned two pockets. The hydrophilic pocket could recognize the nicotinamide moiety of the cofactors by hydrogen bonding networks, while the hydrophobic pocket functioned to position the adenine moiety of the cofactors by hydrophobic and Π-Π stacking interactions. The linker channel contained some key residues for ligand-binding; their mutation could have impact to the specificity of PsXR. Finally, it was found that any of the two single mutations, K21A and K270N, might reverse the cofactor specificity of PsXR from major NADP- to NADdependent, which was further confirmed by the additional experiments. Our findings may provide useful insights into the cofactor specificity of PsXR, stimulating new strategies for better designing xylose reductase and improving ethanol production in industry.

Numerical Simulations of the XR-5 Hall Thruster for Life Assessment at Different Operating Conditions

NASA Technical Reports Server (NTRS)

Lopez Ortega, Alejandro; Jorns, Benjamin A.; Mikellides, Ioannis G.; Hofer, Richard R.

2015-01-01

NASA's Jet Propulsion Laboratory has been investigating the applicability of Aerojet Rocketdyne's XR-5 thruster, a 4.5 kW class Hall thruster, for deep-space missions. Major considerations for qualifying the XR-5 for deep-space missions are demonstration of a wide throttling envelope and a usable life capability in excess of 10,000 h. Numerical simulations with the 2-D axisymmetric code Hall2De are employed to inform the qualification process by assessing erosion rates at the thruster surfaces in a wide range of throttling conditions without the need for conducting costly endurance testing. In previous work at JPL by Jorns et al., the anomalous collision frequency distribution for 11 different throttling conditions of the XR-5 spanning 0.3-4.5 kW were identified based on probe measurements of the electron temperature in the near plume region. In this paper, we provide estimates for the erosion rates at the channel walls and pole covers for the same 11 conditions. Uncertainties in the plasma measurements and in the anomalous collision frequency distribution are addressed by determining upper and lower bounds of the erosion rates. Results suggest that erosion of the walls only occurs in the last 5% of the acceleration channel and the rate of such erosion decreases as the geometry of the thruster changes in time due to magnetic shielding. A quasi-zero-erosion state is eventually achieved in all the examined throttling conditions. Examination of the results for pole surface erosion and estimated cathode life indicates that the XR-5 propellant throughput capability will exceed 700 kg, which provides 50% margin over the usable throughput capability of 466 kg as already demonstrated in wear testing.

Elastomer liners for geothermal tubulars Y267 EPDM Liner Program:

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hirasuna, A.R.; Davis, D.L.; Flickinger, J.E.

1987-12-01

The elastomer, Y267 EPDM, has been identified as a hydrothermally stable material which can operate at temperatures in excess of 320/sup 0/C. The goal of the Y267 Liner Program was to demonstrate the feasibility of using this material as a liner for mild steel tubulars to prevent or mitigate corrosion. If successful, the usage of EPDM lined pipe by the geothermal community may have a significant impact on operating costs and serve as a viable alternative to the use of alloyed tubulars. Tooling procedures were developed under this program to mold a 0.64 cm (0.25'') thick Y267 EPDM liner intomore » a tubular test section 61 cm (2') in length and 19.1 cm (7.5'') in diameter (ID). A successful effort was made to identify a potential coupling agent to be used to bond the elastomer to the steel tubular wall. This agent was found to withstand the processing conditions associated with curing the elastomer at 288/sup 0/C and to retain a significant level of adhesive strength following hydrothermal testing in a synthetic brine at 260/sup 0/C for a period of 166 hours. Bonding tests were conducted on specimens of mild carbon steel and several alloys including Hastelloy C-276. An objective of the program was to field test the lined section of pipe mentioned above at a geothermal facility in the Imperial Valley. Though a test was conducted, problems encountered during the lining operation precluded an encouraging outcome. The results of the field demonstration were inconclusive. 6 refs., 13 figs., 13 tabs« less

Effects of xylitol on xylitol-sensitive versus xylitol-resistant Streptococcus mutans strains in a three-species in vitro biofilm.

PubMed

Marttinen, Aino M; Ruas-Madiedo, Patricia; Hidalgo-Cantabrana, Claudio; Saari, Markku A; Ihalin, Riikka A; Söderling, Eva M

2012-09-01

We studied the effects of xylitol on biofilms containing xylitol-resistant (Xr) and xylitol-sensitive (Xs) Streptococcus mutans, Actinomyces naeslundii and S. sanguinis. The biofilms were grown for 8 and 24 h on hydroxyapatite discs. The viable microorganisms were determined by plate culturing techniques and fluorescence in situ hybridization (FISH) was performed using a S. mutans-specific probe. Extracellular cell-bound polysaccharides (EPS) were determined by spectrofluorometry from single-species S. mutans biofilms. In the presence of 5 % xylitol, the counts of the Xs S. mutans decreased tenfold in the young (8 h) biofilm (p < 0.05) but no effect was seen in the mature (24 h) biofilm. No decrease was observed for the Xr strains, and FISH confirmed these results. No differences were detected in the EPS production of the Xs S. mutans grown with or without xylitol, nor between Xr and Xs S. mutans strains. Thus, it seems that xylitol did not affect the EPS synthesis of the S. mutans strains. Since the Xr S. mutans strains, not inhibited by xylitol, showed no xylitol-induced decrease in the biofilms, we conclude that growth inhibition could be responsible for the decrease of the counts of the Xs S. mutans strains in the clinically relevant young biofilms.

Automated identification of retained surgical items in radiological images

NASA Astrophysics Data System (ADS)

Agam, Gady; Gan, Lin; Moric, Mario; Gluncic, Vicko

2015-03-01

Retained surgical items (RSIs) in patients is a major operating room (OR) patient safety concern. An RSI is any surgical tool, sponge, needle or other item inadvertently left in a patients body during the course of surgery. If left undetected, RSIs may lead to serious negative health consequences such as sepsis, internal bleeding, and even death. To help physicians efficiently and effectively detect RSIs, we are developing computer-aided detection (CADe) software for X-ray (XR) image analysis, utilizing large amounts of currently available image data to produce a clinically effective RSI detection system. Physician analysis of XRs for the purpose of RSI detection is a relatively lengthy process that may take up to 45 minutes to complete. It is also error prone due to the relatively low acuity of the human eye for RSIs in XR images. The system we are developing is based on computer vision and machine learning algorithms. We address the problem of low incidence by proposing synthesis algorithms. The CADe software we are developing may be integrated into a picture archiving and communication system (PACS), be implemented as a stand-alone software application, or be integrated into portable XR machine software through application programming interfaces. Preliminary experimental results on actual XR images demonstrate the effectiveness of the proposed approach.

NOTE: Dose area product evaluations with Gafchromic® XR-R films and a flat-bed scanner

NASA Astrophysics Data System (ADS)

Rampado, O.; Garelli, E.; Deagostini, S.; Ropolo, R.

2006-12-01

Gafchromic® XR-R films are a useful tool to evaluate entrance skin dose in interventional radiology. Another dosimetric quantity of interest in diagnostic and interventional radiology is the dose area product (DAP). In this study, a method to evaluate DAP using Gafchromic® XR-R films and a flat-bed scanner was developed and tested. Film samples were exposed to an x-ray beam of 80 kVp over a dose range of 0 10 Gy. DAP measurements with films were obtained from the digitalization of a film sample positioned over the x-ray beam window during the exposure. DAP values obtained with this method were compared for 23 cardiological interventional procedures with DAP values displayed by the equipment. The overall one-sigma dose measurement uncertainty depended on the absorbed dose, with values below 6% for doses above 1 Gy. A maximum discrepancy of 16% was found, which is of the order of the differences in the DAP measurements that may occur with different calibration procedures. Based on the results presented, after an accurate calibration procedure and a thorough inspection of the relationship between the actual dose and the direct measured quantity (net optical density or net pixel value variation), Gafchromic® XR-R films can be used to assess the DAP.

Current status of atypical antipsychotics for the treatment of fibromyalgia.

PubMed

Rico-Villademoros, F; Calandre, E P; Slim, M

2014-06-01

The treatment of fibromyalgia requires pharmacological and nonpharmacological therapies. The pharmacological treatment of fibromyalgia is limited to a few drugs that have been demonstrated to be moderately effective in some but not all dimensions of the disease. Therefore, the search for new drugs to treat this condition is warranted. Atypical antipsychotics offered an attractive alternative because they had been shown to be active against several key symptoms of fibromyalgia. The results of open-label studies, however, appear to indicate that atypical antipsychotics are poorly tolerated in patients with fibromyalgia, and only quetiapine XR has been studied in randomized controlled trials. Quetiapine XR has demonstrated effectiveness in treating comorbid major depression, anxiety and sleep disturbance. However, in two randomized controlled trials, quetiapine XR was not differentiated from placebo and failed to demonstrate noninferiority to amitriptyline in terms of improving overall symptomatology. The effect of quetiapine XR on pain and its usefulness as part of a combination pharmacological regimen should be further evaluated. Overall, the use of quetiapine (initiated at a low dose and slowly titrated) in fibromyalgia should be limited to patients with comorbid major depression or patients who are currently receiving other treatments and have unresolved and disabling depressive and/or anxiety symptoms. Copyright 2014 Prous Science, S.A.U. or its licensors. All rights reserved.

The effect of welding parameters on surface quality of AA6351 aluminium alloy

NASA Astrophysics Data System (ADS)

Yacob, S.; MAli, M. A.; Ahsan, Q.; Ariffin, N.; Ali, R.; Arshad, A.; Wahab, M. I. A.; Ismail, S. A.; Roji, NS M.; Din, W. B. W.; Zakaria, M. H.; Abdullah, A.; Yusof, M. I.; Kamarulzaman, K. Z.; Mahyuddin, A.; Hamzah, M. N.; Roslan, R.

2015-12-01

In the present work, the effects of gas metal arc welding-cold metal transfer (GMAW-CMT) parameters on surface roughness are experimentally assessed. The purpose of this study is to develop a better understanding of the effects of welding speed, material thickness and contact tip to work distance on the surface roughness. Experiments are conducted using single pass gas metal arc welding-cold metal transfer (GMAW-CMT) welding technique to join the material. The material used in this experiment was AA6351 aluminum alloy with the thickness of 5mm and 6mm. A Mahr Marsuft XR 20 machine was used to measure the average roughness (Ra) of AA6351 joints. The main and interaction effect analysis was carried out to identify process parameters that affect the surface roughness. The results show that all the input process parameters affect the surface roughness of AA6351 joints. Additionally, the average roughness (Ra) results also show a decreasing trend with increased of welding speed. It is proven that gas metal arc welding-cold metal transfer (GMAW-CMT)welding process has been successful in term of providing weld joint of good surface quality for AA6351 based on the low value surface roughness condition obtained in this setup. The outcome of this experimental shall be valuable for future fabrication process in order to obtained high good quality weld.

Elevated temperature biaxial fatigue

NASA Technical Reports Server (NTRS)

Jordan, E. H.

1985-01-01

A 3 year experimental program for studying elevated temperature biaxial fatigue of a nickel based alloy Hastelloy-X has been completed. A new high temperature fatigue test facility with unique capabilities has been developed. Effort was directed toward understanding multiaxial fatigue and correlating the experimental data to the existing theories of fatigue failure. The difficult task of predicting fatigue lives for nonproportional loading was used as an ultimate test for various life prediction methods being considered. The primary means of reaching improved understanding were through several critical nonproportional loading experiments. The direction of cracking observed on failed specimens was also recorded and used to guide the development of the theory. Cyclic deformation responses were permanently recorded digitally during each test. It was discovered that the cracking mode switched from primarily cracking on the maximum shear planes at room temperature to cracking on the maximum normal strain planes at 649 C. In contrast to some other metals, loading path in nonproportional loading had little effect on fatigue lives. Strain rate had a small effect on fatigue lives at 649 C. Of the various correlating parameters the modified plastic work and octahedral shear stress were the most successful.

Cost-effectiveness of extended release naltrexone to prevent relapse among criminal justice-involved individuals with a history of opioid use disorder.

PubMed

Murphy, Sean M; Polsky, Daniel; Lee, Joshua D; Friedmann, Peter D; Kinlock, Timothy W; Nunes, Edward V; Bonnie, Richard J; Gordon, Michael; Chen, Donna T; Boney, Tamara Y; O'Brien, Charles P

2017-08-01

Criminal justice-involved individuals are highly susceptible to opioid relapse and overdose-related deaths. In a recent randomized trial, we demonstrated the effectiveness of extended-release naltrexone (XR-NTX; Vivitrol ® ) in preventing opioid relapse among criminal justice-involved US adults with a history of opioid use disorder. The cost of XR-NTX may be a significant barrier to adoption. Thus, it is important to account for improved quality of life and downstream cost-offsets. Our aims were to (1) estimate the incremental cost per quality-adjusted life-year (QALY) gained for XR-NTX versus treatment as usual (TAU) and evaluate it relative to generally accepted value thresholds; and (2) estimate the incremental cost per additional year of opioid abstinence. Economic evaluation of the aforementioned trial from the taxpayer perspective. Participants were randomized to 25 weeks of XR-NTX injections or TAU; follow-up occurred at 52 and 78 weeks. Five study sites in the US Northeast corridor. A total of 308 participants were randomized to XR-NTX (n = 153) or TAU (n = 155). Incremental costs relative to incremental economic and clinical effectiveness measures, QALYs and abstinent years, respectively. The 25-week cost per QALY and abstinent-year figures were $162 150 and $46 329, respectively. The 78-week figures were $76 400/QALY and $16 371/abstinent year. At 25 weeks, we can be 10% certain that XR-NTX is cost-effective at a value threshold of $100 000/QALY and 62% certain at $200 000/QALY. At 78 weeks, the cost-effectiveness probabilities are 59% at $100 000/QALY and 76% at $200 000/QALY. We can be 95% confident that the intervention would be considered 'good value' at $90 000/abstinent year at 25 weeks and $500/abstinent year at 78 weeks. While extended-release naltrexone appears to be effective in increasing both quality-adjusted life-years (QALYs) and abstinence, it does not appear to be cost-effective using generally accepted value thresholds for QALYs, due to the high price of the injection. © 2017 Society for the Study of Addiction.

Blunt Chest Trauma in Mice after Cigarette Smoke-Exposure: Effects of Mechanical Ventilation with 100% O2.

PubMed

Wagner, Katja; Gröger, Michael; McCook, Oscar; Scheuerle, Angelika; Asfar, Pierre; Stahl, Bettina; Huber-Lang, Markus; Ignatius, Anita; Jung, Birgit; Duechs, Matthias; Möller, Peter; Georgieff, Michael; Calzia, Enrico; Radermacher, Peter; Wagner, Florian

2015-01-01

Cigarette smoking (CS) aggravates post-traumatic acute lung injury and increases ventilator-induced lung injury due to more severe tissue inflammation and apoptosis. Hyper-inflammation after chest trauma is due to the physical damage, the drop in alveolar PO2, and the consecutive hypoxemia and tissue hypoxia. Therefore, we tested the hypotheses that 1) CS exposure prior to blunt chest trauma causes more severe post-traumatic inflammation and thereby aggravates lung injury, and that 2) hyperoxia may attenuate this effect. Immediately after blast wave-induced blunt chest trauma, mice (n=32) with or without 3-4 weeks of CS exposure underwent 4 hours of pressure-controlled, thoraco-pulmonary compliance-titrated, lung-protective mechanical ventilation with air or 100% O2. Hemodynamics, lung mechanics, gas exchange, and acid-base status were measured together with blood and tissue cytokine and chemokine concentrations, heme oxygenase-1 (HO-1), activated caspase-3, and hypoxia-inducible factor 1-α (HIF-1α) expression, nuclear factor-κB (NF-κB) activation, nitrotyrosine formation, purinergic receptor 2X4 (P2XR4) and 2X7 (P2XR7) expression, and histological scoring. CS exposure prior to chest trauma lead to higher pulmonary compliance and lower PaO2 and Horovitz-index, associated with increased tissue IL-18 and blood MCP-1 concentrations, a 2-4-fold higher inflammatory cell infiltration, and more pronounced alveolar membrane thickening. This effect coincided with increased activated caspase-3, nitrotyrosine, P2XR4, and P2XR7 expression, NF-κB activation, and reduced HIF-1α expression. Hyperoxia did not further affect lung mechanics, gas exchange, pulmonary and systemic cytokine and chemokine concentrations, or histological scoring, except for some patchy alveolar edema in CS exposed mice. However, hyperoxia attenuated tissue HIF-1α, nitrotyrosine, P2XR7, and P2XR4 expression, while it increased HO-1 formation in CS exposed mice. Overall, CS exposure aggravated post-traumatic inflammation, nitrosative stress and thereby organ dysfunction and injury; short-term, lung-protective, hyperoxic mechanical ventilation have no major beneficial effect despite attenuation of nitrosative stress, possibly due to compensation of by regional alveolar hypoxia and/or consecutive hypoxemia, resulting in down-regulation of HIF-1α expression.

Chronomodulation of topotecan or X-radiation treatment increases treatment efficacy without enhancing acute toxicity.

PubMed

Mullins, Dana; Proulx, Denise; Saoudi, A; Ng, Cheng E

2005-05-01

Topotecan (TPT), a camptothecin analog, is currently used to treat human ovarian and small-cell lung cancer and is in clinical trials for other tumor sites. However, it is unknown whether chronomodulation of TPT treatment is beneficial. We examined the effects of administering TPT or X-radiation (XR) alone at different times of the day or night. We treated mice bearing human colorectal tumor xenografts at four different times representing the early rest period (9 am or 3 HALO [hours after light onset]), late rest period (3 pm or 9 HALO), early active period (9 pm or 15 HALO), and late active period (3 am or 21 HALO) of the mice. We gave either TPT (12 mg/kg, injected i.p.) or XR (4 Gy, directed to the tumor) twice weekly on Days 0, 4, 7, 10 within 2 weeks. Treatment with either TPT or XR at 3 am demonstrated the greatest efficacy (measured by a tumor regrowth assay) without significantly increasing acute toxicity (assessed by a decrease in leukocyte counts or body weight). Conversely, treatment at 3 pm, in particular, showed increased toxicity without any enhanced efficacy. Our study provided the first evidence that chronomodulation of TPT treatments, consistent with the findings of other camptothecin analogs, is potentially clinically beneficial. Additionally, our findings suggest that chronomodulation of fractionated XR treatments is also potentially clinically beneficial.

Correlates of retention on extended-release naltrexone among persons living with HIV infection transitioning to the community from the criminal justice system.

PubMed

Springer, Sandra A; Brown, Shan-Estelle; Di Paola, Angela; Altice, Frederick L

2015-12-01

The acceptability of and retention on extended-release naltrexone (XR-NTX), an FDA-approved medication for the treatment of alcohol and opioid use disorders, among persons living with HIV disease (PLH) under criminal justice setting (CJS) supervision has not been evaluated to date. Two double-blind placebo-controlled randomized trials of XR-NTX for inmates with HIV disease transitioning to the community with (1) alcohol use disorders (AUDs) or (2) opioid use disorders, are underway. Reasons for not accepting XR-NTX and an evaluation of differences in demographic features between those who were retained on study drug and those who did not return for their second injection post-release are discussed. 70% of eligible persons consented to participate; almost 90% received their first injection; and almost 60% returned for their first injection after release. Variables found to be associated (p<0.10) with returning for the second injection included: not meeting criteria for hazardous drinking (p=0.035; OR 0.424 (CI 0.191-0.941)); being prescribed antiretroviral therapy (p=0.068; OR 2.170 (CI 0.943-4.992)); expressing experiencing serious depression 30 days prior to incarceration (p=0.068; OR 1.889 (CI 0.955-3.737)); not having a positive cocaine urine screen on the day of release (DOR) (p=0.011; OR 0.258 (CI 0.091-0.729)); and not meeting criteria for an AUD plus any substance use disorder (p=0.068; OR 0.521 (CI 0.259-1.048)). Only positive cocaine urine test on DOR was statistically significant after multivariate regression analyses (p=0.005; OR 0.207 (CI 0.068-0.623)). CJS based XR-NTX programs are highly acceptable among PLH, however retention on XR-NTX after release is negatively impacted by relapse to cocaine use. Published by Elsevier Ireland Ltd.

A randomized double-blind, placebo-controlled trial of venlafaxine-extended release for co-occurring cannabis dependence and depressive disorders.

PubMed

Levin, Frances R; Mariani, John; Brooks, Daniel J; Pavlicova, Martina; Nunes, Edward V; Agosti, Vito; Bisaga, Adam; Sullivan, Maria A; Carpenter, Kenneth M

2013-06-01

To evaluate whether venlafaxine-extended release (VEN-XR) is an effective treatment for cannabis dependence with concurrent depressive disorders. This was a randomized, 12-week, double-blind, placebo-controlled trial of out-patients (n = 103) with DSM-IV cannabis dependence and major depressive disorder or dysthymia. Participants received up to 375 mg VEN-XR on a fixed-flexible schedule or placebo. All patients received weekly individual cognitive-behavioral psychotherapy that primarily targeted marijuana use. The trial was conducted at two university research centers in the United States. One hundred and three cannabis-dependent adults participated in the trial. The primary outcome measures were (i) abstinence from marijuana defined as at least two consecutive urine-confirmed abstinent weeks and (ii) improvement in depressive symptoms based on the Hamilton Depression Rating Scale. The proportion of patients achieving a clinically significant mood improvement (50% decrease in Hamilton Depression score from baseline) was high and did not differ between groups receiving VEN-XR (63%) and placebo (69%) (χ1 (2)  = 0.48, P = 0.49). The proportion of patients achieving abstinence was low overall, but was significantly worse on VEN-XR (11.8%) compared to placebo (36.5%) (χ1 (2)  = 7.46, P < 0.01; odds ratio = 4.51, 95% confidence interval: 1.53, 13.3). Mood improvement was associated with reduction in marijuana use in the placebo group (F1,179  = 30.49, P < 0.01), but not the VEN-XR group (F1,186  = 0.02, P = 0.89). For depressed, cannabis-dependent patients, venlafaxine-extended release does not appear to be effective at reducing depression and may lead to an increase in cannabis use. © 2013 Society for the Study of Addiction.

Comparison of Healthcare Utilization Among Patients Treated With Alcoholism Medications

PubMed Central

Mark, Tami L.; Montejano, Leslie B.; Kranzler, Henry R.; Chalk, Mady; Gastfriend, David R.

2014-01-01

Objectives To determine in a large claims database the healthcare utilization and costs associated with treatment of alcohol dependence with medications vs no medication and across 4 US Food and Drug Administration (FDA)–approved medications. Study Design Claims database analysis. Methods Eligible adults with alcohol dependence claims (n = 27,135) were identified in a commercial database (MarketScan; Thomson Reuters Inc, Chicago, Illinois). Following propensity score–based matching and inverse probability weighting on demographic, clinical, and healthcare utilization variables, patients who had used an FDA-approved medication for alcohol dependence (n = 2977) were compared with patients who had not (n = 2977). Patients treated with oral naltrexone hydrochloride (n = 2064), oral disulfiram (n = 2076), oral acamprosate calcium (n = 5068), or extended-release injectable naltrexone (naltrexone XR) (n = 295) were also compared for 6-month utilization rates of alcoholism medication, inpatient detoxification days, alcoholism-related inpatient days, and outpatient services, as well as inpatient charges. Results Patients who received alcoholism medications had fewer inpatient detoxification days (706 vs 1163 days per 1000 patients, P <.001), alcoholism-related inpatient days (650 vs 1086 days, P <.001), and alcoholism-related emergency department visits (127 vs 171, P = .005). Among 4 medications, the use of naltrexone XR was associated with fewer inpatient detoxification days (224 days per 1000 patients) than the use of oral naltrexone (552 days, P = .001), disulfiram (403 days, P = .049), or acamprosate (525 days, P <.001). The group receiving naltrexone XR also had fewer alcoholism-related inpatient days than the groups receiving disulfiram or acamprosate. More patients in the naltrexone XR group had an outpatient substance abuse visit compared with patients in the oral alcoholism medication groups. Conclusion Patients who received an alcoholism medication had lower healthcare utilization than patients who did not. Naltrexone XR showed an advantage over oral medications in healthcare utilization and costs. PMID:21348558

The Primary Glucose-Lowering Effect of Metformin Resides in the Gut, Not the Circulation: Results From Short-term Pharmacokinetic and 12-Week Dose-Ranging Studies.

PubMed

Buse, John B; DeFronzo, Ralph A; Rosenstock, Julio; Kim, Terri; Burns, Colleen; Skare, Sharon; Baron, Alain; Fineman, Mark

2016-02-01

Delayed-release metformin (Met DR) is formulated to deliver the drug to the lower bowel to leverage the gut-based mechanisms of metformin action with lower plasma exposure. Met DR was assessed in two studies. Study 1 compared the bioavailability of single daily doses of Met DR to currently available immediate-release metformin (Met IR) and extended-release metformin (Met XR) in otherwise healthy volunteers. Study 2 assessed glycemic control in subjects with type 2 diabetes (T2DM) over 12 weeks. Study 1 was a phase 1, randomized, four-period crossover study in 20 subjects. Study 2 was a 12-week, phase 2, multicenter, placebo-controlled, dose-ranging study in 240 subjects with T2DM randomized to receive Met DR 600, 800, or 1,000 mg administered once daily; blinded placebo; or unblinded Met XR 1,000 or 2,000 mg (reference). The bioavailability of 1,000 mg Met DR b.i.d. was ∼50% that of Met IR and Met XR (study 1). In study 2, 600, 800, and 1,000 mg Met DR q.d. produced statistically significant, clinically relevant, and sustained reductions in fasting plasma glucose (FPG) levels over 12 weeks compared with placebo, with an ∼40% increase in potency compared with Met XR. The placebo-subtracted changes from baseline in HbA1c level at 12 weeks were consistent with changes in FPG levels. All treatments were generally well tolerated, and adverse events were consistent with Glucophage/Glucophage XR prescribing information. Dissociation of the glycemic effect from plasma exposure with gut-restricted Met DR provides strong evidence for a predominantly lower bowel-mediated mechanism of metformin action. © 2016 by the American Diabetes Association. Readers may use this article as long as the work is properly cited, the use is educational and not for profit, and the work is not altered.

Improved techniques for thermomechanical testing in support of deformation modeling

NASA Technical Reports Server (NTRS)

Castelli, Michael G.; Ellis, John R.

1992-01-01

The feasibility of generating precise thermomechanical deformation data to support constitutive model development was investigated. Here, the requirement is for experimental data that is free from anomalies caused by less than ideal equipment and procedures. A series of exploratory tests conducted on Hastelloy X showed that generally accepted techniques for strain controlled tests were lacking in at least three areas. Specifically, problems were encountered with specimen stability, thermal strain compensation, and temperature/mechanical strain phasing. The source of these difficulties was identified and improved thermomechanical testing techniques to correct them were developed. These goals were achieved by developing improved procedures for measuring and controlling thermal gradients and by designing a specimen specifically for thermomechanical testing. In addition, innovative control strategies were developed to correctly proportion and phase the thermal and mechanical components of strain. Subsequently, the improved techniques were used to generate deformation data for Hastelloy X over the temperature range, 200 to 1000 C.

Design of a 25-kWe Surface Reactor System Based on SNAP Reactor Technologies

NASA Astrophysics Data System (ADS)

Dixon, David D.; Hiatt, Matthew T.; Poston, David I.; Kapernick, Richard J.

2006-01-01

A Hastelloy-X clad, sodium-potassium (NaK-78) cooled, moderated spectrum reactor using uranium zirconium hydride (UZrH) fuel based on the SNAP program reactors is a promising design for use in surface power systems. This paper presents a 98 kWth reactor for a power system the uses multiple Stirling engines to produce 25 kWe-net for 5 years. The design utilizes a pin type geometry containing UZrHx fuel clad with Hastelloy-X and NaK-78 flowing around the pins as coolant. A compelling feature of this design is its use of 49.9% enriched U, allowing it to be classified as a category III-D attractiveness and reducing facility costs relative to highly-enriched space reactor concepts. Presented below are both the design and an analysis of this reactor's criticality under various safety and operations scenarios.

Domain Processes in Ferroelectric Ceramics

DTIC Science & Technology

1994-04-14

elastic strain tensor and eikl is the Levi - Civita density. Eqs (11) and (12) has three nontrivial solutions: Xr3 = 0 (13) Xr"= -1 { [ 2sj2Q 12 -Sl I...ABSTRACT (aA~iMUM 200 wardt) This report Outlines the progres achieved during a two year effort sponsored by the AFOSR on the theoretical study of domain...INTRODUCTION This is the final progress report for this two year program sponsored by the Air Force Office of Scientific Research on "Domain Processes in

In Situ Materials Study in Hot Hydrothermal Vent Fluid

NASA Astrophysics Data System (ADS)

Holland, P. M.; Schindele, W. J.; Holland, C. E.; Lilley, M. D.; Olson, E. J.

2004-12-01

We are developing methods and technology for in situ sampling and analysis of volatiles from hot hydrothermal vent fluids inside the mixing boundary. These fluids can reach temperatures of up to 400° C and are known to be corrosive to most materials. While titanium has been the material of choice for contact with these fluids, we wanted to assess whether other materials, such as Hastelloy or nickel might be suitable for in situ sampling from hydrothermal vents. For the present study, small (1/16" o.d.) tubes of chemically pure titanium, Hastelloy C, and Nickel 200 were prepared, using 316 stainless steel as a control. These were placed in an assembly with other test items, and inserted into the hydrothermal vent Sully in the Main Endeavor Field on the Juan de Fuca Plate in June 2003 by the Jason II ROV operated from the R/V Thompson. The assembly was retrieved 46 days later after exposure to approximately 360° C hydrothermal vent fluid at a depth of 2200 m. Inspection showed the stainless steel to be completely eroded away and nickel to be extensively corroded, however both the Hastelloy and titanium tubes were in excellent condition with the 0.030" i.d. passages in the tubes remaining open. Other test items included a miniature titanium filtered inlet fitting containing an 80 mesh titanium screen made of 0.004" (0.1 mm) chemically pure titanium wire, an Inconel washer and a sapphire ball. Apart from some discoloration, there appeared to be no significant degradation in these materials apart from signs of etching on the sapphire.

Thermally Simulated Testing of a Direct-Drive Gas-Cooled Nuclear Reactor

NASA Technical Reports Server (NTRS)

Godfroy, Thomas; Bragg-Sitton, Shannon; VanDyke, Melissa

2003-01-01

This paper describes the concept and preliminary component testing of a gas-cooled, UN-fueled, pin-type reactor which uses He/Xe gas that goes directly into a recuperated Brayton system to produce electricity for nuclear electric propulsion. This Direct-Drive Gas-Cooled Reactor (DDG) is designed to be subcritical under water or wet-sand immersion in case of a launch accident. Because the gas-cooled reactor can directly drive the Brayton turbomachinery, it is possible to configure the system such that there are no external surfaces or pressure boundaries that are refractory metal, even though the gas delivered to the turbine is 1144 K. The He/Xe gas mixture is a good heat transport medium when flowing, and a good insulator when stagnant. Judicious use of stagnant cavities as insulating regions allows transport of the 1144-K gas while keeping all external surfaces below 900 K. At this temperature super-alloys (Hastelloy or Inconel) can be used instead of refractory metals. Super-alloys reduce the technology risk because they are easier to fabricate than refractory metals, we have a much more extensive knowledge base on their characteristics, and, because they have a greater resistance to oxidation, system testing is eased. The system is also relatively simple in its design: no additional coolant pumps, heat exchanger, or freeze-thaw systems are required. Key to success of this concept is a good knowledge of the heat transfer between the fuel pins and the gas, as well as the pressure drop through the system. This paper describes preliminary testing to obtain this key information, as well as experience in demonstrating electrical thermal simulation of reactor components and concepts.

Direct-Drive Gas-Cooled Reactor Power System: Concept and Preliminary Testing

NASA Technical Reports Server (NTRS)

Wright, S. A.; Lipinski, R. J.; Godfroy, T. J.; Bragg-Sitton, S. M.; VanDyke, M. K.

2002-01-01

This paper describes the concept and preliminary component testing of a gas-cooled, UN-fueled, pin-type reactor which uses He/Xe gas that goes directly into a recuperated Brayton system to produce electricity for nuclear electric propulsion. This Direct-Drive Gas-Cooled Reactor (DDG) is designed to be subcritical under water or wet- sand immersion in case of a launch accident. Because the gas-cooled reactor can directly drive the Brayton turbomachinery, it is possible to configure the system such that there are no external surfaces or pressure boundaries that are refractory metal, even though the gas delivered to the turbine is 1144 K. The He/Xe gas mixture is a good heat transport medium when flowing, and a good insulator when stagnant. Judicious use of stagnant cavities as insulating regions allows transport of the 1144-K gas while keeping all external surfaces below 900 K. At this temperature super-alloys (Hastelloy or Inconel) can be used instead of refractory metals. Super-alloys reduce the technology risk because they are easier to fabricate than refractory metals, we have a much more extensive knowledge base on their characteristics, and, because they have a greater resistance to oxidation, system testing is eased. The system is also relatively simple in its design: no additional coolant pumps, heat exchanger, or freeze-thaw systems are required. Key to success of this concept is a good knowledge of the heat transfer between the fuel pins and the gas, as well as the pressure drop through the system. This paper describes preliminary testing to obtain this key information, as well as experience in demonstrating electrically heated testing of simulated reactor components.

Model‐Informed Development and Registration of a Once‐Daily Regimen of Extended‐Release Tofacitinib

PubMed Central

Lamba, M; Hutmacher, MM; Furst, DE; Dikranian, A; Dowty, ME; Conrado, D; Stock, T; Nduaka, C; Cook, J

2017-01-01

Extended‐release (XR) formulations enable less frequent dosing vs. conventional (e.g., immediate release (IR)) formulations. Regulatory registration of such formulations typically requires pharmacokinetic (PK) and clinical efficacy data. Here we illustrate a model‐informed, exposure–response (E‐R) approach to translate controlled trial data from one formulation to another without a phase III trial, using a tofacitinib case study. Tofacitinib is an oral Janus kinase (JAK) inhibitor for the treatment of rheumatoid arthritis (RA). E‐R analyses were conducted using validated clinical endpoints from phase II dose–response and nonclinical dose fractionation studies of the IR formulation. Consistent with the delay in clinical response dynamics relative to PK, average concentration was established as the relevant PK parameter for tofacitinib efficacy and supported pharmacodynamic similarity. These evaluations, alongside demonstrated equivalence in total systemic exposure between IR and XR formulations, provided the basis for the regulatory approval of tofacitinib XR once daily by the US Food and Drug Administration. PMID:27859030

Combined mutagenesis of Rhodosporidium toruloides for improved production of carotenoids and lipids.

PubMed

Zhang, Chaolei; Shen, Hongwei; Zhang, Xibin; Yu, Xue; Wang, Han; Xiao, Shan; Wang, Jihui; Zhao, Zongbao K

2016-10-01

To improve production of lipids and carotenoids by the oleaginous yeast Rhodosporidium toruloides by screening mutant strains. Upon physical mutagenesis of the haploid strain R. toruloides np11 with an atmospheric and room temperature plasma method followed by chemical mutagenesis with nitrosoguanidine, a mutant strain, R. toruloides XR-2, formed dark-red colonies on a screening plate. When cultivated in nitrogen-limited media, XR-2 cells grew slower but accumulated 0.23 g lipids/g cell dry wt and 0.75 mg carotenoids/g CDW. To improve its production capacity, different amino acids and vitamins were supplemented. p-Aminobenzoic acid and tryptophan had beneficial effects on cell growth. When cultivated in nitrogen-limited media in the presence of selected vitamins, XR-2 accumulated 0.41 g lipids/g CDW and 0.69 mg carotenoids/g CDW. A mutant R. toruloides strain with improved production profiles for lipids and carotenoids was obtained, indicating its potential to use combined mutagenesis for a more productive phenotype.

Metformin extended release treatment of adolescent obesity: a 48-week randomized, double-blind, placebo-controlled trial with 48-week follow-up.

PubMed

Wilson, Darrell M; Abrams, Stephanie H; Aye, Tandy; Lee, Phillip D K; Lenders, Carine; Lustig, Robert H; Osganian, Stavroula V; Feldman, Henry A

2010-02-01

Metformin has been proffered as a therapy for adolescent obesity, although long-term controlled studies have not been reported. To test the hypothesis that 48 weeks of daily metformin hydrochloride extended release (XR) therapy will reduce body mass index (BMI) in obese adolescents, as compared with placebo. Multicenter, randomized, double-blind, placebo-controlled clinical trial. The 6 centers of the Glaser Pediatric Research Network from October 2003 to August 2007. Obese (BMI > or = 95th percentile) adolescents (aged 13-18 years) were randomly assigned to the intervention (n = 39) or placebo groups. Intervention Following a 1-month run-in period, subjects following a lifestyle intervention program were randomized 1:1 to 48 weeks' treatment with metformin hydrochloride XR, 2000 mg once daily, or an identical placebo. Subjects were monitored for an additional 48 weeks. Main Outcome Measure Change in BMI, adjusted for site, sex, race, ethnicity, and age and metformin vs placebo. After 48 weeks, mean (SE) adjusted BMI increased 0.2 (0.5) in the placebo group and decreased 0.9 (0.5) in the metformin XR group (P = .03). This difference persisted for 12 to 24 weeks after cessation of treatment. No significant effects of metformin on body composition, abdominal fat, or insulin indices were observed. Metformin XR caused a small but statistically significant decrease in BMI when added to a lifestyle intervention program. clinicaltrials.gov Identifiers: NCT00209482 and NCT00120146.

Modification of the NEMA XR21-2000 cardiac phantom for testing of imaging systems used in endovascular image guided interventions.

PubMed

Ionita, C N; Dohatcu, A; Jain, A; Keleshis, C; Hoffmann, K R; Bednarek, D R; Rudin, S

2009-01-01

X-ray equipment testing using phantoms that mimic the specific human anatomy, morphology, and structure is a very important step in the research, development, and routine quality assurance for such equipment. Although the NEMA XR21 phantom exists for cardiac applications, there is no such standard phantom for neuro-, peripheral and cardio-vascular angiographic applications. We have extended the application of the NEMA XR21-2000 phantom to evaluate neurovascular x-ray imaging systems by structuring it to be head-equivalent; two aluminum plates shaped to fit into the NEMA phantom geometry were added to a 15 cm thick section. Also, to enable digital subtraction angiography (DSA) testing, two replaceable central plates with a hollow slot were made so that various angiographic sections could be inserted into the phantom. We tested the new modified phantom using a flat panel C-arm unit dedicated for endovascular image-guided interventions. All NEMA XR21-2000 standard test sections were used in evaluations with the new "head-equivalent" phantom. DSA and DA are able to be tested using two standard removable blocks having simulated arteries of various thickness and iodine concentrations (AAPM Report 15). The new phantom modifications have the benefits of enabling use of the standard NEMA phantom for angiography in both neuro- and cardio-vascular applications, with the convenience of needing only one versatile phantom for multiple applications. Additional benefits compared to using multiple phantoms are increased portability and lower cost.

Modification of the NEMA XR21-2000 cardiac phantom for testing of imaging systems used in endovascular image guided interventions

NASA Astrophysics Data System (ADS)

Ionita, C. N.; Dohatcu, A.; Jain, A.; Keleshis, C.; Hoffmann, K. R.; Bednarek, D. R.; Rudin, S.

2009-02-01

X-ray equipment testing using phantoms that mimic the specific human anatomy, morphology, and structure is a very important step in the research, development, and routine quality assurance for such equipment. Although the NEMA XR21 phantom exists for cardiac applications, there is no such standard phantom for neuro-, peripheral and cardiovascular angiographic applications. We have extended the application of the NEMA XR21-2000 phantom to evaluate neurovascular x-ray imaging systems by structuring it to be head-equivalent; two aluminum plates shaped to fit into the NEMA phantom geometry were added to a 15 cm thick section. Also, to enable digital subtraction angiography (DSA) testing, two replaceable central plates with a hollow slot were made so that various angiographic sections could be inserted into the phantom. We tested the new modified phantom using a flat panel C-arm unit dedicated for endovascular image-guided interventions. All NEMA XR21-2000 standard test sections were used in evaluations with the new "headequivalent" phantom. DSA and DA are able to be tested using two standard removable blocks having simulated arteries of various thickness and iodine concentrations (AAPM Report 15). The new phantom modifications have the benefits of enabling use of the standard NEMA phantom for angiography in both neuro- and cardio-vascular applications, with the convenience of needing only one versatile phantom for multiple applications. Additional benefits compared to using multiple phantoms are increased portability and lower cost.

The free form XR photovoltaic concentrator: a high performance SMS3D design

NASA Astrophysics Data System (ADS)

Cvetkovic, Aleksandra; Hernandez, Maikel; Benítez, Pablo; Miñano, Juan C.; Schwartz, Joel; Plesniak, Adam; Jones, Russ; Whelan, David

2008-08-01

A novel photovoltaic concentrator is presented. The goal is to achieve high concentration design with high efficiency and high acceptance angle that in the same time is compact and convenient for thermal and mechanical management. This photovoltaic system is based on 1 cm2 multi-junction tandem solar cells and an XR concentrator. The XR concentrator in this system is an SMS 3D design formed by one reflective (X) and one refractive (R) free-form surfaces (i.e., without rotational or linear symmetry) and has been chosen for its excellent aspect ratio and for its ability to perform near the thermodynamic limit. It is a mirror-lens device that has no shadowing elements and has square entry aperture (the whole system aperture area is used for collecting light). This large acceptance angle relaxes the manufacturing tolerances of all the optical and mechanical components of the system included the concentrator itself and is one of the keys to get a cost competitive photovoltaic generator. For the geometrical concentration of 1000x the simulation results show the acceptance angle of +/-1.8 deg. The irradiance distribution on the cell is achieved with ultra-short homogenizing prism, whose size is optimised to keep the maximum values under the ones that the cell can accept. The application of the XR optics to high-concentration is being developed in a consortium leaded by The Boeing Company, which has been awarded a project by US DOE in the framework of the Solar America Initiative.

Venlafaxine extended-release for depression following spinal cord injury: a randomized clinical trial.

PubMed

Fann, Jesse R; Bombardier, Charles H; Richards, J Scott; Wilson, Catherine S; Heinemann, Allen W; Warren, Ann Marie; Brooks, Larry; McCullumsmith, Cheryl B; Temkin, Nancy R; Warms, Catherine; Tate, Denise G

2015-03-01

Depression is prevalent and associated with negative outcomes in individuals with spinal cord injury (SCI). Antidepressants are used routinely to treat depression, yet no placebo-controlled trials have been published in this population to our knowledge. To determine the efficacy and tolerability of venlafaxine hydrochloride extended-release (XR) for major depressive disorder (MDD) or dysthymic disorder in persons with chronic SCI. Multisite, randomized (1:1), double-blind, placebo-controlled Project to Improve Symptoms and Mood After SCI (PRISMS) trial. All research staff conducting screening, intervention, and outcome procedures were blinded to randomization status. We screened 2536 patients from outpatient clinics at 6 SCI treatment centers in the United States and randomized 133 participants into the trial. Participants were 18 to 64 years old and at least 1 month after SCI, with MDD or dysthymic disorder. Seventy-four percent of participants were male, and participants were on average 40 years old and 11 years after SCI. Forty-seven percent had cervical injuries, 53.4% had American Spinal Injury Association injury severity A (complete injury) SCI, 24.1% had at least 2 prior MDD episodes, and 99.2% had current MDD. Common comorbidities included chronic pain (93.9%), significant anxiety (57.1%), and history of substance dependence (44.4%). Twelve-week trial of venlafaxine XR vs placebo using a flexible-dose algorithm. The Hamilton Depression Rating Scale (HAM-D 17-item version and Maier subscale, which focuses on core depression symptoms and excludes somatic symptoms) over 12 weeks. Mixed-effects models revealed a significant difference between the venlafaxine XR and placebo groups in improvement on the Maier subscale from baseline to 12 weeks (treatment effect, 1.6; 95% CI, 0.3-2.9; P = .02) but not on the HAM-D 17-item version (treatment effect, 1.0; 95% CI, -1.4 to 3.4; P = .42). Participants receiving venlafaxine XR reported significantly less SCI-related disability on the Sheehan Disability Scale at 12 weeks compared with placebo (treatment effect, 4.7; 95% CI, 1.5-7.8; P = .005). Blurred vision was the only significantly more common new or worsening adverse effect in the venlafaxine XR group compared with the placebo group over 12 weeks. Venlafaxine XR was well tolerated by most patients and an effective antidepressant for decreasing core symptoms of depression and improving SCI-related disability. Further research is needed to determine the optimal treatment and measurement approaches for depression in chronic SCI. clinicaltrials.gov Identifier: NCT00592384.

TBL1XR1/TP63: a novel recurrent gene fusion in B-cell non-Hodgkin lymphoma | Office of Cancer Genomics

Cancer.gov

Recently, the landscape of single base mutations in diffuse large B-cell lymphoma (DLBCL) was described. Here we report the discovery of a gene fusion between TBL1XR1 and TP63, the only recurrent somatic novel gene fusion identified in our analysis of transcriptome data from 96 DLBCL cases. Based on this cohort and a further 157 DLBCL cases analyzed by FISH, the incidence in de novo germinal center B cell-like (GCB) DLBCL is 5% (6 of 115).

Engineering and Development Support of General Decon Technology for the DARCOM Installation Restoration Program. Task 1. Lagoon/Landfill Liner Compatibility Testing with Explosives.

DTIC Science & Technology

1983-06-01

NOTES 19. KEY WORDS (Continue on reveree side if necesaary and Identify by block number) Neoprene Synthetic Liners TCE, XR-5, EPDM Hypalon Compatibility...CPE, Hypalon , XR-5, HDPE, Neoprene, and EPDM ) were immersed in TNT, RDX, and TCE solutions for I week. Liner and test .*. method selection and data...Mean Weight Change Values - EPDM /Neoprene Group 57 Unexposed and in Distilled Water 7 Mean Weight Change Values - PVC Group in Distilled 58 Water and in

Improved welding of Rene-41

NASA Technical Reports Server (NTRS)

Nunez, S.

1970-01-01

Gas-tungsten arc welding with a filler of Rene-41 produces strong welded joints. When Rene-41 is used, resistance to strain-age cracking is greatly increased by post-weld solution annealing in an inert atmosphere. Mechanical properties of Rene-41 and Hastelloy-W are compared.

Modeling the rubbing contact in honeycomb seals

NASA Astrophysics Data System (ADS)

Fischer, Tim; Welzenbach, Sarah; Meier, Felix; Werner, Ewald; kyzy, Sonun Ulan; Munz, Oliver

2018-03-01

Metallic honeycomb labyrinth seals are commonly used as sealing systems in gas turbine engines. Because of their capability to withstand high thermo-mechanical loads and oxidation, polycrystalline nickel-based superalloys, such as Hastelloy X and Haynes 214, are used as sealing material. In addition, these materials must exhibit a tolerance against rubbing between the rotating part and the stationary seal component. The tolerance of the sealing material against rubbing preserves the integrity of the rotating part. In this article, the rubbing behavior at the rotor-stator interface is considered numerically. A simulation model is incorporated into the commercial finite element code ABAQUS/explicit and is utilized to simulate a simplified rubbing process. A user-defined interaction routine between the contact surfaces accounts for the thermal and mechanical interfacial behavior. Furthermore, an elasto-plastic constitutive material law captures the extreme temperature conditions and the damage behavior of the alloys. To validate the model, representative quantities of the rubbing process are determined and compared with experimental data from the literature. The simulation results correctly reproduce the observations made on a test rig with a reference stainless steel material (AISI 304). A parametric study using the nickel-based superalloys reveals a clear dependency of the rubbing behavior on the sliding and incursion velocity. Compared to each other, the two superalloys studied exhibit a different rubbing behavior.

Plant Insecticide L-Canavanine Repels Drosophila via the Insect Orphan GPCR DmX

PubMed Central

Framery, Bérénice; Bockaert, Joël; Parmentier, Marie-Laure; Grau, Yves

2009-01-01

For all animals, the taste sense is crucial to detect and avoid ingesting toxic molecules. Many toxins are synthesized by plants as a defense mechanism against insect predation. One example of such a natural toxic molecule is l-canavanine, a nonprotein amino acid found in the seeds of many legumes. Whether and how insects are informed that some plants contain l-canavanine remains to be elucidated. In insects, the taste sense relies on gustatory receptors forming the gustatory receptor (Gr) family. Gr proteins display highly divergent sequences, suggesting that they could cover the entire range of tastants. However, one cannot exclude the possibility of evolutionarily independent taste receptors. Here, we show that l-canavanine is not only toxic, but is also a repellent for Drosophila. Using a pharmacogenetic approach, we find that flies sense food containing this poison by the DmX receptor. DmXR is an insect orphan G-protein–coupled receptor that has partially diverged in its ligand binding pocket from the metabotropic glutamate receptor family. Blockade of DmXR function with an antagonist lowers the repulsive effect of l-canavanine. In addition, disruption of the DmXR encoding gene, called mangetout (mtt), suppresses the l-canavanine repellent effect. To avoid the ingestion of l-canavanine, DmXR expression is required in bitter-sensitive gustatory receptor neurons, where it triggers the premature retraction of the proboscis, thus leading to the end of food searching. These findings show that the DmX receptor, which does not belong to the Gr family, fulfills a gustatory function necessary to avoid eating a natural toxin. PMID:19564899

THE EFFECTS OF DRONABINOL DURING DETOXIFICATION AND THE INITIATION OF TREATMENT WITH EXTENDED RELEASE NALTREXONE

PubMed Central

Bisaga, Adam; Sullivan, Maria A.; Glass, Andrew; Mishlen, Kaitlyn; Pavlicova, Martina; Haney, Margaret; Raby, Wilfrid N.; Levin, Frances R.; Carpenter, Kenneth M.; Mariani, John J.; Nunes, Edward V.

2015-01-01

Background Evidence suggests that the cannabinoid system is involved in the maintenance of opioid dependence. We examined whether dronabinol, a cannabinoid receptor type 1 partial agonist, reduces opioid withdrawal and increases retention in treatment with extended release naltrexone (XR-naltrexone). Methods Opioid dependent participants were randomized to receive dronabinol 30 mg/d (n=40) or placebo (n=20), under double-blind conditions, while they underwent inpatient detoxification and naltrexone induction. Before discharge all participants received an injection of XR-naltrexone, with an additional dose given four weeks later. Dronabinol or placebo was given while inpatient and for 5 weeks afterwards. The primary outcomes were the severity of opioid withdrawal, measured with the Subjective Opioid Withdrawal Scale, and retention in treatment at the end of the inpatient phase and at the end of the 8-week trial. Results The severity of opioid withdrawal during inpatient phase was lower in the dronabinol group relative to placebo group (p=0.006). Rates of successful induction onto XR-naltrexone (dronabinol 66%, placebo 55%) and completion of treatment (dronabinol 35%, placebo 35%) were not significantly different. Post-hoc analysis showed that the 32% of participants who smoked marijuana regularly during the outpatient phase had significantly lower ratings of insomnia and anxiety and were more likely to complete the 8-week trial. Conclusion Dronabinol reduced the severity of opiate withdrawal during acute detoxification but had no effect on rates of XR-naltrexone treatment induction and retention. Participants who elected to smoke marijuana during the trial were more likely to complete treatment regardless of treatment group assignment. PMID:26187456

The Improvement of Utilization Ratio of Metal Organic Sources for the Low Cost Preparation of MOCVD-synthesized YBCO Films based on a Self-heating Technology

NASA Astrophysics Data System (ADS)

Zhao, Ruipeng; Liu, Qing; Xia, Yudong; Tao, Bowan; Li, Yanrong

2017-12-01

We have successfully applied metal organic chemical vapor deposition (MOCVD) to synthesize biaxially textured YBa2Cu3O7-δ (YBCO) superconducting films on the templates of LaMnO3/epitaxial MgO/IBAD-MgO/solution deposition planarization (SDP) Y2O3/Hastelloy tape. The YBCO films have obtained dense and smooth surface with good structure and performance. A new self-heating method, which replaced the conventional heating-wire radiation heating method, has been used to heat the Hastelloy metal tapes by us. Compared with the heating-wire radiation heating method, the self-heating method shows higher energy efficiency and lower power consumption, which has good advantage to simplify the structure of the MOCVD system. Meanwhile, the utilization ratio of metal organic sources can be increased from 6% to 20% through adopting the new self-heating method. Then the preparation cost of the YBCO films can be also greatly reduced.

Probing the electronic structures of [Cu2(mu-XR2)]n+ diamond cores as a function of the bridging X atom (X = N or P) and charge (n = 0, 1, 2).

PubMed

Harkins, Seth B; Mankad, Neal P; Miller, Alexander J M; Szilagyi, Robert K; Peters, Jonas C

2008-03-19

A series of dicopper diamond core complexes that can be isolated in three different oxidation states ([Cu2(mu-XR2)]n+, where n = 0, 1, 2 and X = N or P) is described. Of particular interest is the relative degree of oxidation of the respective copper centers and the bridging XR2 units, upon successive oxidations. These dicopper complexes feature terminal phosphine and either bridging amido or phosphido donors, and as such their metal-ligand bonds are highly covalent. Cu K-edge, Cu L-edge, and P K-edge spectroscopies, in combination with solid-state X-ray structures and DFT calculations, provides a complementary electronic structure picture for the entire set of complexes that tracks the involvement of a majority of ligand-based redox chemistry. The electronic structure picture that emerges for these inorganic dicopper diamond cores shares similarities with the Cu2(mu-SR)2 CuA sites of cytochrome c oxidases and nitrous oxide reductases.

Perspectives: Black Holes

NASA Technical Reports Server (NTRS)

Dolan, Joseph F.; Fisher, Richard R. (Technical Monitor)

2001-01-01

When asked to discuss Cyg XR-1, E. E. Salpeter once concluded, 'A black hole in Cyg X(R)-1 is the most conservative hypothesis.' Recent observations now make it likely that a black hole in Cyg XR-1 is the only hypothesis tenable. Chandrasekhar first showed that compact stars - those with the inward force of gravity on their outer layers balanced by the pressure generated by the Pauli exclusion principle acting on its electrons (in white dwarfs) or nucleons (in neutron stars) - have a maximum mass. Equilibrium is achieved at a minimum of the total energy of the star, which is the sum of the positive Fermi energy and the negative gravitational energy. The maximum mass attainable in equilibrium is found by setting E = 0: M(max) = 1.5 M(Sun). If the mass of the star is larger than this, then E can be decreased without bound by decreasing the star's radius and increasing its (negative) gravitational energy. No equilibrium value of the radius exist, and general relativity predicts that gravitational collapse to a point occurs. This point singularity is a black hole.

Field experiment of 800× off-axis XR-Köhler concentrator module on a carousel tracker

NASA Astrophysics Data System (ADS)

Yamada, Noboru; Okamoto, Kazuya; Ijiro, Toshikazu; Suzuki, Takao; Maemura, Toshihiko; Kawaguchi, Takashi; Takahashi, Hiroshi; Sato, Takashi; Hernandez, Maikel; Benitez, Pablo; Chaves, Julio; Cvetkovic, Aleksandra; Vilaplana, Juan; Mohedano, Ruben; Mendes-Lopes, Joao; Miñano, Juan Carlos

2013-09-01

This paper presents the design and preliminary experimental results of a concentrator-type photovoltaic module based on a free-form off-axis 800×XR-Köhler concentrator. The off-axis XR-Köhler concentrator is one of the advanced concentrators that perform high concentration with a large acceptance angle and excellent irradiance uniformity on a solar cell. As a result of on-sun characterization of the unglazed single-cell unit test rig, the temperature-corrected DC module efficiency was 32.2% at 25 °C without an anti-reflective (AR) coating on the secondary optics, and the acceptance angle was more than ±1.0°. In addition, the non-corrected DC efficiency of an individual cell in a glazed 8-cell unit module mounted on a carousel tracking system was measured. The individual efficiency deviated in the range of 24.3-27.4%, owing to the mirror shape and alignment errors. The resultant series-connected efficiency was approximately 25% at direct normal irradiation (DNI) of 770 W/m2.

Proton Induced X-Ray Emission (PIXE): Determining the Concentration of Samples

NASA Astrophysics Data System (ADS)

McCarthy, Mallory; Rodriguez Manso, Alis; Pajouhafsar, Yasmin; J Yennello, Sherry

2017-09-01

We used Proton Induced X-ray Emission (PIXE) as an analysis technique to determine the composition of samples, in particular, the elemental constituents and the concentrations. Each of the samples are bombarded with protons, which in result displaces a lower level electron and causes a higher level electron to fall into its place. This displacement produces characteristic x-rays that are `fingerprints' for each element. The protons supplied for the bombardment are produced and accelerated by the K150 proton beam in the Cyclotron Institute at Texas A&M University. The products are detected by three x-ray detectors: XR-100CR Si-PIN, XR-100SDD, and XR-100T CdTe. The peaks of the spectrum are analyzed using a software analysis tool, GUPIXWIN, to determine the concentration of the known elements of each particular sample. The goals of this work are to test run the Proton Induced X-Ray Emission experimental set up at Texas A&M University (TAMU) and to determine the concentration of thin films containing KBr given by the TAMU Chemical Engineering Department.

78 FR 42584 - Bureau of International Security and Nonproliferation: Report to Congress Pursuant to Section...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-16

...-finished metals such as aluminum and steel, coal, and software for integrating industrial processes. We...; boron; cobalt; copper; copper infiltrated tungsten; copper- beryllium; graphite; hastelloy; inconel; magnesium; molybdenum; nickel; niobium; silver infiltrated tungsten; steels (including, but not limited to...

Noncontaminating technique for making holes in existing process systems

NASA Technical Reports Server (NTRS)

Hecker, T. P.; Czapor, H. P.; Giordano, S. M.

1972-01-01

Technique is developed for making cleanly-contoured holes in assembled process systems without introducing chips or other contaminants into system. Technique uses portable equipment and does not require dismantling of system. Method was tested on Inconel, stainless steel, ASTMA-53, and Hastelloy X in all positions.

A genetic overhaul of Saccharomyces cerevisiae 424A(LNH-ST) to improve xylose fermentation.

PubMed

Bera, Aloke K; Ho, Nancy W Y; Khan, Aftab; Sedlak, Miroslav

2011-05-01

Robust microorganisms are necessary for economical bioethanol production. However, such organisms must be able to effectively ferment both hexose and pentose sugars present in lignocellulosic hydrolysate to ethanol. Wild type Saccharomyces cerevisiae can rapidly ferment hexose, but cannot ferment pentose sugars. Considerable efforts were made to genetically engineer S. cerevisiae to ferment xylose. Our genetically engineered S cerevisiae yeast, 424A(LNH-ST), expresses NADPH/NADH xylose reductase (XR) that prefer NADPH and NAD(+)-dependent xylitol dehydrogenase (XD) from Pichia stipitis, and overexpresses endogenous xylulokinase (XK). This strain is able to ferment glucose and xylose, as well as other hexose sugars, to ethanol. However, the preference for different cofactors by XR and XD might lead to redox imbalance, xylitol excretion, and thus might reduce ethanol yield and productivity. In the present study, genes responsible for the conversion of xylose to xylulose with different cofactor specificity (1) XR from N. crassa (NADPH-dependent) and C. parapsilosis (NADH-dependent), and (2) mutant XD from P. stipitis (containing three mutations D207A/I208R/F209S) were overexpressed in wild type yeast. To increase the NADPH pool, the fungal GAPDH enzyme from Kluyveromyces lactis was overexpressed in the 424A(LNH-ST) strain. Four pentose phosphate pathway (PPP) genes, TKL1, TAL1, RKI1 and RPE1 from S. cerevisiae, were also overexpressed in 424A(LNH-ST). Overexpression of GAPDH lowered xylitol production by more than 40%. However, other strains carrying different combinations of XR and XD, as well as new strains containing the overexpressed PPP genes, did not yield any significant improvement in xylose fermentation.

Novel Pharmacokinetic-Pharmacodynamic Model for Prediction of Outcomes with an Extended-Release Formulation of Ciprofloxacin

PubMed Central

Meagher, Alison K.; Forrest, Alan; Dalhoff, Axel; Stass, Heino; Schentag, Jerome J.

2004-01-01

The pharmacokinetics of an extended-release (XR) formulation of ciprofloxacin has been compared to that of the immediate-release (IR) product in healthy volunteers. The only significant difference in pharmacokinetic parameters between the two formulations was seen in the rate constant of absorption, which was approximately 50% greater with the IR formulation. The geometric mean plasma ciprofloxacin concentrations were applied to an in vitro pharmacokinetic-pharmacodynamic model exposing three different clinical strains of Escherichia coli (MICs, 0.03, 0.5, and 2.0 mg/liter) to 24 h of simulated concentrations in plasma. A novel mathematical model was derived to describe the time course of bacterial CFU, including capacity-limited replication and first-order rate of bacterial clearance, and to model the effects of ciprofloxacin concentrations on these processes. A “mixture model” was employed which allowed as many as three bacterial subpopulations to describe the total bacterial load at any moment. Comparing the two formulations at equivalent daily doses, the rates and extents of bacterial killing were similar with the IR and XR formulations at MICs of 0.03 and 2.0 mg/liter. At an MIC of 0.5 mg/liter, however, the 1,000-mg/day XR formulation showed a moderate advantage in antibacterial effect: the area under the CFU-time curve was 45% higher for the IR regimen; the nadir log CFU and 24-h log CFU values for the IR regimen were 3.75 and 2.49, respectively; and those for XR were 4.54 and 3.13, respectively. The mathematical model explained the differences in bacterial killing rate for two regimens with identical AUC/MIC ratios. PMID:15155200

Heterologous expression of Spathaspora passalidarum xylose reductase and xylitol dehydrogenase genes improved xylose fermentation ability of Aureobasidium pullulans.

PubMed

Guo, Jian; Huang, Siyao; Chen, Yefu; Guo, Xuewu; Xiao, Dongguang

2018-04-30

Aureobasidium pullulans is a yeast-like fungus that can ferment xylose to generate high-value-added products, such as pullulan, heavy oil, and melanin. The combinatorial expression of two xylose reductase (XR) genes and two xylitol dehydrogenase (XDH) genes from Spathaspora passalidarum and the heterologous expression of the Piromyces sp. xylose isomerase (XI) gene were induced in A. pullulans to increase the consumption capability of A. pullulans on xylose. The overexpression of XYL1.2 (encoding XR) and XYL2.2 (encoding XDH) was the most beneficial for xylose utilization, resulting in a 17.76% increase in consumed xylose compared with the parent strain, whereas the introduction of the Piromyces sp. XI pathway failed to enhance xylose utilization efficiency. Mutants with superior xylose fermentation performance exhibited increased intracellular reducing equivalents. The fermentation performance of all recombinant strains was not affected when glucose or sucrose was utilized as the carbon source. The strain with overexpression of XYL1.2 and XYL2.2 exhibited excellent fermentation performance with mimicked hydrolysate, and pullulan production increased by 97.72% compared with that of the parent strain. The present work indicates that the P4 mutant (using the XR/XDH pathway) with overexpressed XYL1.2 and XYL2.2 exhibited the best xylose fermentation performance. The P4 strain showed the highest intracellular reducing equivalents and XR and XDH activity, with consequently improved pullulan productivity and reduced melanin production. This valuable development in aerobic fermentation by the P4 strain may provide guidance for the biotransformation of xylose to high-value products by A. pullulans through genetic approach.

High-energy X-ray spectra of Cygnus XR-1 observed from OSO 8

NASA Technical Reports Server (NTRS)

Dolan, J. F.; Crannell, C. J.; Dennis, B. R.; Frost, K. J.; Orwig, L. E.

1979-01-01

X-ray spectra of Cygnus XR-1 were measured with the scintillation spectrometer aboard the OSO 8 satellite during a period of one-and-one-half to three weeks in each of the years from 1975 to 1977. Typical spectra of the source between 15 and 250 keV are presented and the spectra are found to be well represented by a single power-law expression whose photon number spectral index is different for the two intensity states that were considered. The observed pivoting effect is consistent with two-temperature accretion disk models of the X-ray emitting region.

Dual utilization of NADPH and NADH cofactors enhances xylitol production in engineered Saccharomyces cerevisiae.

PubMed

Jo, Jung-Hyun; Oh, Sun-Young; Lee, Hyeun-Soo; Park, Yong-Cheol; Seo, Jin-Ho

2015-12-01

Xylitol, a natural sweetener, can be produced by hydrogenation of xylose in hemicelluloses. In microbial processes, utilization of only NADPH cofactor limited commercialization of xylitol biosynthesis. To overcome this drawback, Saccharomyces cerevisiae D452-2 was engineered to express two types of xylose reductase (XR) with either NADPH-dependence or NADH-preference. Engineered S. cerevisiae DWM expressing both the XRs exhibited higher xylitol productivity than the yeast strain expressing NADPH-dependent XR only (DWW) in both batch and glucose-limited fed-batch cultures. Furthermore, the coexpression of S. cerevisiae ZWF1 and ACS1 genes in the DWM strain increased intracellular concentrations of NADPH and NADH and improved maximum xylitol productivity by 17%, relative to that for the DWM strain. Finally, the optimized fed-batch fermentation of S. cerevisiae DWM-ZWF1-ACS1 resulted in 196.2 g/L xylitol concentration, 4.27 g/L h productivity and almost the theoretical yield. Expression of the two types of XR utilizing both NADPH and NADH is a promising strategy to meet the industrial demands for microbial xylitol production. Copyright © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Particle Induced X-Ray Emission experiment using the K150 3.6 MeV proton beam at TAMU Cyclotron Institute

NASA Astrophysics Data System (ADS)

Pajouhafsar, Yasmin; Alis Manso Rodriguez Team; Sherry Yennello Team

2017-09-01

Particle Induced X-Ray Emission (PIXE) is a non-destructive analytical technique that is used for various tasks, such as elemental composition. The x-rays are emitted when electrons transition from higher to lower energy levels, causing vacancies in the atom's electron configuration. The overall goals of this research are to successfully set up a PIXE experiment and to obtain elemental concentrations for various samples, using the K150 proton beam in the Cyclotron Institute at Texas A&M University. The x-rays produced are unique to each element and analyzed with reference to their known energies. The setup consists of 3 different detectors, providing a wide range of energies: XR-100T CdTe γ/X-Ray, XR-100T/CR Si and XR-100SDD. Accelerating 3.6 MeV protons from the K150 and using PIXE, we determine concentrations from the NaCl samples provided by the Chemical Engineering Department. The concentrations for each element found in the NaCl thin films are obtained and analyzed through the software, GUPIXWIN. DOE Grant (DE-FG02-93ER40773) and Welch Foundation (A-1266).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fontainha, C.C.P.; Nolasco, A.V.; Santos, A.P.

Radiation dosimetry is commonly used to prevent deterministic radiation effects in high dose medical procedures. Radiochromic films find nowadays widely application in radiotherapy, interventional procedures and CT exams for isodose and maximum skin dose measurements. Moreover the size of the irradiated area and its distribution can be performed through the reading of the individual components in the RGB-spectrum. Particularly, radiochromic film has multiple advantages over alternative dosimeters for low-kV X-rays dosimetry. Concerned to spatial resolution it is far superior to that of ionization chambers and thermoluminescent dosimeters. For high energy photon fields (keV to MeV) the most used radiochromic filmmore » commercially available belongs to the EBT Gafchromic{sup R} series. On the other hand, for low energy photon fields in the x-ray range (20 kVp to 200 kVp) the best choice belongs to the XR-QA Gafchromic{sup R} film series. In this work we demonstrate the possibility of generating 2D images of thin polymeric composites films using EBT3 and XR-QA2 Gafchromic{sup R} films exposed to 6 MeV and 40 keV x-ray photons, respectively, using the digital filtering tools of the ImageJ{sup R} free software. In this context, EBT3 films were placed on the surface of a rigid anthropomorphic phantom. Then, they were covered with a thermoplastic mask made of PCL polymer. This setup was then exposed to 2.0 Gy absorbed dose in the Linear Accelerator beam. The EBT3 films were then scanned in the high resolution mode in a commercial scanner and the images subsequently treated with digital filters. It is somehow possible to see the image of the thermoplastic mask in the scanned image. However, in the treated image it is easy to observe the mask arrangement. The unexpected phenomenon here is the EB3 film ability to detect the attenuation of high energy photons by a plastic material, which in turn has a very low mass-energy attenuation coefficient, producing a very clear 2D image. This result is discussed in terms of the high Z halides added to the sensitive layer of EB3 film, once the main components are C (42.3%), H (39.7%) and O (16.0%)1-2. Based on the above results, we have speculated about the abilities of XR-AQ films in the detection of the distribution of nano-sized particles that has high mass-energy attenuation coefficients for low energy x-rays, in polymer composites. In another investigation we tested the ability of XR-QA2 Gafchromic{sup R} films to evaluate the dispersion of ZrO{sub 2} nano-sized grain clusters in protective composites. The P(VDFTrFE)/ ZrO{sub 2} film was sandwiched between two XR-QA2 radiochromic films. In this setup, one radiochromic film is directly exposed to 100 mGy of the x-rays beam and another one measures the attenuated beam. After storage for 24 hours at room temperature under no light conditions, the irradiated radiochromic films were scanned under the same conditions in order to obtain a more reliable result. All films were scanned using the same size ROI in high resolution mode and saved as tagged image file format (TIFF). The untreated scanned image of the XR-AQ2 film directed exposed to the X-ray beam and the correspondent treated image with digital filters are shown. The untreated and treated image of the XR-AQ2 film that was exposed to the attenuated x-ray beam is shown. The image treated with digital filters seems to reproduce the dispersion of ZrO{sub 2} nano-sized grain clusters in the P(VDF-TrFE) copolymer matrix. This result is also discussed in terms of the high Z halides added to the sensitive layer of XR-AQ2 film and compared to the MEV images obtained from the P(VDF-TrFE)/ZrO{sub 2} composites. The results indicate a clear correlation between the 2D radiochromic image and the MEV photography.« less

Determination of the relative resistance to ignition of selected turbopump materials in high-pressure, high-temperature, oxygen environments, volume 2

NASA Technical Reports Server (NTRS)

Stoltzfus, Joel M.; Benz, Frank J.

1986-01-01

Data from the particle impact tests are presented. Results are provided for the frictional heating tests of pairs of like materials. The materials tested include: Hastelloy X, Inconel 600, Invar 36, Monel K-500, Monel 400, nickel 200, silicon carbide, stainless steel 316, and zironium copper.

Staphylococcus aureus activates type I IFN signaling in mice and humans through the Xr repeated sequences of protein A

PubMed Central

Martin, Francis J.; Gomez, Marisa I.; Wetzel, Dawn M.; Memmi, Guido; O’Seaghdha, Maghnus; Soong, Grace; Schindler, Christian; Prince, Alice

2009-01-01

The activation of type I IFN signaling is a major component of host defense against viral infection, but it is not typically associated with immune responses to extracellular bacterial pathogens. Using mouse and human airway epithelial cells, we have demonstrated that Staphylococcus aureus activates type I IFN signaling, which contributes to its virulence as a respiratory pathogen. This response was dependent on the expression of protein A and, more specifically, the Xr domain, a short sequence–repeat region encoded by DNA that consists of repeated 24-bp sequences that are the basis of an internationally used epidemiological typing scheme. Protein A was endocytosed by airway epithelial cells and subsequently induced IFN-β expression, JAK-STAT signaling, and IL-6 production. Mice lacking IFN-α/β receptor 1 (IFNAR-deficient mice), which are incapable of responding to type I IFNs, were substantially protected against lethal S. aureus pneumonia compared with wild-type control mice. The profound immunological consequences of IFN-β signaling, particularly in the lung, may help to explain the conservation of multiple copies of the Xr domain of protein A in S. aureus strains and the importance of protein A as a virulence factor in the pathogenesis of staphylococcal pneumonia. PMID:19603548

Hydration structure of the barite (001)–water interface: Comparison of x-ray reflectivity with molecular dynamics simulations

DOE PAGES

Bracco, Jacquelyn N.; Lee, Sang Soo; Stubbs, Joanne E.; ...

2017-05-11

The three-dimensional structure of the barite (001)-water interface was studied using in situ specular and non-specular X-ray reflectivity (XR). Displacements of the barium and sulfate ions in the surface of a barite crystal and the interfacial water structure were defined in the analyses. The largest relaxations (0.13 Å lateral and 0.08 Å vertical) were observed for the barium and sulfate ions in the topmost unit cell layer, which diminished rapidly with depth. The best fit structure identified four distinct adsorbed species, which in comparison with molecular dynamics (MD) simulations, reveals that they are associated with positions of adsorbed water, eachmore » of which coordinates one or two surface ions (either barium, sulfate, or both). These water molecules also adsorb in positions consistent with those of bariums and sulfates in the bulk crystal lattice. These results demonstrate the importance of combining high resolution XR with MD simulations to fully describe the atomic structure of the hydrated mineral surface. As a result, the agreement between the results indicates both the uniqueness of the structural model obtained from the XR analysis and the accuracy of the force field used in the simulations.« less

Hydration structure of the barite (001)–water interface: Comparison of x-ray reflectivity with molecular dynamics simulations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bracco, Jacquelyn N.; Lee, Sang Soo; Stubbs, Joanne E.

The three-dimensional structure of the barite (001)-water interface was studied using in situ specular and non-specular X-ray reflectivity (XR). Displacements of the barium and sulfate ions in the surface of a barite crystal and the interfacial water structure were defined in the analyses. The largest relaxations (0.13 Å lateral and 0.08 Å vertical) were observed for the barium and sulfate ions in the topmost unit cell layer, which diminished rapidly with depth. The best fit structure identified four distinct adsorbed species, which in comparison with molecular dynamics (MD) simulations, reveals that they are associated with positions of adsorbed water, eachmore » of which coordinates one or two surface ions (either barium, sulfate, or both). These water molecules also adsorb in positions consistent with those of bariums and sulfates in the bulk crystal lattice. These results demonstrate the importance of combining high resolution XR with MD simulations to fully describe the atomic structure of the hydrated mineral surface. As a result, the agreement between the results indicates both the uniqueness of the structural model obtained from the XR analysis and the accuracy of the force field used in the simulations.« less

An update on central nervous system stimulant formulations in children and adolescents with attention-deficit/hyperactivity disorder.

PubMed

Chavez, Benjamin; Sopko, Michael A; Ehret, Megan J; Paulino, Raphael E; Goldberg, Kyle R; Angstadt, Kristine; Bogart, Gregory T

2009-06-01

To review recent literature on the different stimulant preparations regarding efficacy and safety in children and adolescents with attention-deficit/hyperactivity disorder (ADHD) and describe advantages and disadvantages of the many available dosage formulations. Literature retrieval was performed through PubMed/MEDLINE (2005-December 2008) using the terms methylphenidate, amphetamines, central nervous system stimulants, and attention-deficit/hyperactivity disorder. In addition, reference citations from publications identified were reviewed and drug manufacturers were contacted for any possible additional references. Double-blind clinical trials found using the search criteria listed above were included for review. Open-label studies and studies prior to 2005 were included if no double-blind trials were published for that formulation within the time period reviewed. The literature reviewed here demonstrates the efficacy and safety of stimulant medications in children and adolescents with ADHD. However, there are 19 different formulations of stimulants, leading to confusion and errors in prescribing and dispensing of these drugs. Knowing and understanding the advantages and disadvantages of the different formulations can lead to individualized treatment. Formulations like Concerta, Focalin-XR, Adderall-XR, and Vyvanse provide the convenience of once-daily dosing. Each of these provides varying amount of stimulants at different times of the day. Vyvanse has a unique delivery system that may lower the risk of patients abusing their medication. Daytrana gives patients more control over their dosing by being able to choose when the patch is removed; it is also a feasible alternative for children who cannot swallow pills. For patients who cannot swallow tablets or capsules, the capsules of Focalin-XR, Adderall-XR, Metadate-CD, and Ritalin-LA can be opened and sprinkled on applesauce. Stimulants are effective medications to treat the symptoms of ADHD. The multiple available dosage forms allow for individualization of treatment.

Development of the Small Package Single Particle Soot Photometer with extended range (SP2-XR) and black carbon detection efficiency compared to its predecessor, the SP2

NASA Astrophysics Data System (ADS)

Schulz, H.; Kok, G. L.; Zanatta, M.; Schwarz, J. P.; Herber, A. B.

2016-12-01

Black carbon (BC) aerosol is an important contributor to climate change due to its ability to very efficiently absorb solar radiation. The Single Particle Soot Photometer (SP2) is an instrument that quantifies the refractory mass of individual BC-containing particles with a laser-induced incandescence method. The SP2 has been deployed on ships, at ground based sites, and on research aircraft to quantify BC's mass loadings and microphysical properties. However, the SP2's particle detection range is generally limited to 70-700 nm volume-equivalent diameter for ambient BC. Ambient air typically contains substantial number concentrations below and mass concentrations above the limits of this range. To account for the unquantified particles, it is common to fit a log-normal distribution to the measured size distributions — an approach that leaves the BC community with uncertain results, and a need to learn about the occurrence of very small particles or very large BC aggregates. The SP2 is also large and heavy enough to limit its usability for aircraft and unmanned or towed airborne vehicles. We have developed a miniaturized SP2 to dramatically extend the range of applications for which the SP2 technique can be used. This new instrument, with the additional target of an extended measurement range, has been named the SP2-XR, and incorporates a newly designed optical block with updated electronics for signal recording and on-the-fly processing (gain stitching and peak analysis). The optical block improves the light-collection of both scattered and incandescent light from sampled particles. The target measurement range is 40-1000 nm. At the same time, the SP2-XR weighs less than half of an SP2 (15 kg for the complete system), and about 1/4 the volume ( 20 cm x 20 cm x 40 cm). The instrument software is designed to produce ready to use particle mass and binned size distributions or full particle trace records, according to different scientific needs. Thus, an SP2-XR may produce a much slimmer data set while deployed in the field, compared to the SP2. We have compared the size-resolved detection efficiency and performance of the SP2-XR to two classic SP2 system using a DMA/CPC system. Measurements covered different BC standards (Aquadag and Fullerene Soot), PSL particles, and ambient aerosol. Test results will be presented.

Calibration of GafChromic XR-RV3 radiochromic film for skin dose measurement using standardized x-ray spectra and a commercial flatbed scanner.

PubMed

McCabe, Bradley P; Speidel, Michael A; Pike, Tina L; Van Lysel, Michael S

2011-04-01

In this study, newly formulated XR-RV3 GafChromic film was calibrated with National Institute of Standards and Technology (NIST) traceability for measurement of patient skin dose during fluoroscopically guided interventional procedures. The film was calibrated free-in-air to air kerma levels between 15 and 1100 cGy using four moderately filtered x-ray beam qualities (60, 80, 100, and 120 kVp). The calibration films were scanned with a commercial flatbed document scanner. Film reflective density-to-air kerma calibration curves were constructed for each beam quality, with both the orange and white sides facing the x-ray source. A method to correct for nonuniformity in scanner response (up to 25% depending on position) was developed to enable dose measurement with large films. The response of XR-RV3 film under patient backscattering conditions was examined using on-phantom film exposures and Monte Carlo simulations. The response of XR-RV3 film to a given air kerma depended on kVp and film orientation. For a 200 cGy air kerma exposure with the orange side of the film facing the source, the film response increased by 20% from 60 to 120 kVp. At 500 cGy, the increase was 12%. When 500 cGy exposures were performed with the white side facing the x-ray source, the film response increased by 4.0% (60 kVp) to 9.9% (120 kVp) compared to the orange-facing orientation. On-phantom film measurements and Monte Carlo simulations show that using a NIST-traceable free-in-air calibration curve to determine air kerma in the presence of backscatter results in an error from 2% up to 8% depending on beam quality. The combined uncertainty in the air kerma measurement from the calibration curves and scanner nonuniformity correction was +/- 7.1% (95% C.I.). The film showed notable stability. Calibrations of film and scanner separated by 1 yr differed by 1.0%. XR-RV3 radiochromic film response to a given air kerma shows dependence on beam quality and film orientation. The presence of backscatter slightly modifies the x-ray energy spectrum; however, the increase in film response can be attributed primarily to the increase in total photon fluence at the sensitive layer. Film calibration curves created under free-in-air conditions may be used to measure dose from fluoroscopic quality x-ray beams, including patient backscatter with an error less than the uncertainty of the calibration in most cases.

Characterization of XR-RV3 GafChromic{sup ®} films in standard laboratory and in clinical conditions and means to evaluate uncertainties and reduce errors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farah, J., E-mail: jad.farah@irsn.fr; Clairand, I.; Huet, C.

2015-07-15

Purpose: To investigate the optimal use of XR-RV3 GafChromic{sup ®} films to assess patient skin dose in interventional radiology while addressing the means to reduce uncertainties in dose assessment. Methods: XR-Type R GafChromic films have been shown to represent the most efficient and suitable solution to determine patient skin dose in interventional procedures. As film dosimetry can be associated with high uncertainty, this paper presents the EURADOS WG 12 initiative to carry out a comprehensive study of film characteristics with a multisite approach. The considered sources of uncertainties include scanner, film, and fitting-related errors. The work focused on studying filmmore » behavior with clinical high-dose-rate pulsed beams (previously unavailable in the literature) together with reference standard laboratory beams. Results: First, the performance analysis of six different scanner models has shown that scan uniformity perpendicular to the lamp motion axis and that long term stability are the main sources of scanner-related uncertainties. These could induce errors of up to 7% on the film readings unless regularly checked and corrected. Typically, scan uniformity correction matrices and reading normalization to the scanner-specific and daily background reading should be done. In addition, the analysis on multiple film batches has shown that XR-RV3 films have generally good uniformity within one batch (<1.5%), require 24 h to stabilize after the irradiation and their response is roughly independent of dose rate (<5%). However, XR-RV3 films showed large variations (up to 15%) with radiation quality both in standard laboratory and in clinical conditions. As such, and prior to conducting patient skin dose measurements, it is mandatory to choose the appropriate calibration beam quality depending on the characteristics of the x-ray systems that will be used clinically. In addition, yellow side film irradiations should be preferentially used since they showed a lower dependence on beam parameters compared to white side film irradiations. Finally, among the six different fit equations tested in this work, typically used third order polynomials and more rational and simplistic equations, of the form dose inversely proportional to pixel value, were both found to provide satisfactory results. Fitting-related uncertainty was clearly identified as a major contributor to the overall film dosimetry uncertainty with up to 40% error on the dose estimate. Conclusions: The overall uncertainty associated with the use of XR-RV3 films to determine skin dose in the interventional environment can realistically be estimated to be around 20% (k = 1). This uncertainty can be reduced to within 5% if carefully monitoring scanner, film, and fitting-related errors or it can easily increase to over 40% if minimal care is not taken. This work demonstrates the importance of appropriate calibration, reading, fitting, and other film-related and scan-related processes, which will help improve the accuracy of skin dose measurements in interventional procedures.« less

JOURNEY II XR Safety and Effectiveness PMCF

ClinicalTrials.gov

2018-04-19

Rheumatoid Vasculitis With Rheumatoid Arthritis of Knee; Unilateral Post-Traumatic Osteoarthritis of Knee; Knee Osteoarthritis; Degenerative Arthritis Peripheral Joint; Failed Osteotomies; Failed Unicompartmental Replacement

76 FR 78284 - Pediatric Advisory Committee; Notice of Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-16

... Prevnar 13 (Pneumococcal 13-valent Conjugate Vaccine (Diphtheria CRM197 Protein), Cervarix (Human Papillomavirus Bivalent (Types 16 and 18) vaccine, recombinant, Focalin XR (dexmethylphenidate), Daytrana...

Visible absorption properties of radiation exposed XR type-T radiochromic film.

PubMed

Butson, Martin J; Cheung, Tsang; Yu, Peter K N

2004-10-07

The visible absorption spectra of Gafchromic XR type-T radiochromic film have been investigated to analyse the dosimetry characteristics of the film with visible light densitometers. Common densitometers can use photospectrometry, fluorescent light (broad-band visible), helium neon (632 nm), light emitting diode (LED) or other specific bandwidth spectra. The visible absorption spectra of this film when exposed to photon radiation show peaks at 676 nm and 618 nm at 2 Gy absorbed doses which shift to slightly lower wavelengths (662 nm and 612 nm at 8 Gy absorbed dose) at higher doses. This is similar to previous models of Gafchromic film such as MD-55-2 and HS but XR type-T also includes a large absorption at lower visible wavelengths due to 'yellow' dyes placed within the film to aid with visible recognition of the film exposure level. The yellow dye band pass is produced at approximately 520 nm to 550 nm and absorbs wavelengths lower than this value within the visible spectrum. This accounts for the colour change from yellow to brown through the added absorption in the red wavelengths with radiation exposure. The film produces a relatively high dose sensitivity with up to 0.25 OD units per Gy change at 672 nm at 100 kVp x-ray energy. Variations in dose sensitivity can be achieved by varying wavelength analysis.

How Well Are We Respecting Patient Privacy in Medical Imaging? Lessons Learnt From a Departmental Audit.

PubMed

Dilauro, Marc; Thornhill, Rebecca; Fasih, Najla

2016-11-01

Preservation of patient privacy and dignity are basic requirements for all patients visiting a hospital. The purpose of this study was to perform an audit of patients' satisfaction with privacy whilst in the Department of Medical Imaging (MI) at the Civic Campus of the Ottawa Hospital. Outpatients who underwent magnetic resonance imaging (MRI), computed tomography (CT), ultrasonography (US), and plain film (XR) examinations were provided with a survey on patient privacy. The survey asked participants to rank (on a 6-point scale ranging from 6 = excellent to 1 = no privacy) whether their privacy was respected in 5 key locations within the Department of MI. The survey was conducted over a consecutive 5-day period. A total of 502 surveys were completed. The survey response rate for each imaging modality was: 55% MRI, 42% CT, 45% US, and 47% XR. For each imaging modality, the total percentage of privacy scores greater than or equal to 5 were: 98% MRI, 96% CT, 94% US, and 92% XR. Privacy ratings for the MRI reception and waiting room areas were significantly higher in comparison to the other imaging modalities (P = .0025 and P = .0227, respectively). Overall, patient privacy was well respected within the Department of MI. Copyright © 2016 Canadian Association of Radiologists. Published by Elsevier Inc. All rights reserved.

Topiramate

MedlinePlus

... another medication with a name similar to the brand name for topiramate. You should be sure that ... The sprinkle and extended-release capsules (Qudexy XR brand only) may be swallowed whole or opened and ...

Saquinavir

MedlinePlus

... lung disease); simvastatin (Zocor, in Vytorin); tacrolimus (Astagraf XL, Envarsus XR, Protopic); thioridazine; trazodone; triazolam (Halcion); or ... Tenormin, in Tenoretic), labetalol (Trandate), metoprolol (Lopressor, Toprol XL, in Dutoprol, in Loressor HCT), nadolol (Corgard, in ...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akiyama, Benjamin M.; Laurence, Hannah M.; Massey, Aaron R.

The outbreak of Zika virus (ZIKV) and associated fetal microcephaly mandates efforts to understand the molecular processes of infection. Related flaviviruses produce noncoding subgenomic flaviviral RNAs (sfRNAs) that are linked to pathogenicity in fetal mice. These viruses make sfRNAs by co-opting a cellular exonuclease via structured RNAs called xrRNAs. We found that ZIKV-infected monkey and human epithelial cells, mouse neurons, and mosquito cells produce sfRNAs. The RNA structure that is responsible for ZIKV sfRNA production forms a complex fold that is likely found in many pathogenic flaviviruses. Mutations that disrupt the structure affect exonuclease resistance in vitro and sfRNA formationmore » during infection. The complete ZIKV xrRNA structure clarifies the mechanism of exonuclease resistance and identifies features that may modulate function in diverse flaviviruses.« less

Deconvolution by Homomorphic and Wiener Filtering

DTIC Science & Technology

1988-09-01

XR?(e-j) =XR(e. 7w), XJ(e-jw) -Xei) and 4 ej) -Re’) ,ej)X~i) d+ ar g [X(e l a)[ ( Assumnption: both X(z) and X(z) are analytic in a region included the...consistent if 3k(wi+,) E IJ" g (X(ej"’+’)/wiJ - Arg[X(ej’")] + 2irk(wi+t ) < THLDI < r. The idea of the algorithm is to adapt the step size Aw imtil the phase...given by arg X(ejw) = S(eJw) dw, or, according to [141 ’ G " g [X(e-’÷.’)/T ,= argX(ejw) + LAW d argX(e(’+ )+ dargX(ei’) 1T2 where d-S(e’) = argX(e3d

Benefits Analysis of Past Projects. Volume 2. Individual Project Assessments.

DTIC Science & Technology

1984-11-01

209 S- ..-...-......... a nineteenth century one which had been developed for .he braiding of fire hoses . Project Results The program revealed...was found for protecting the drilling and position sensing optics from expelled metal particles. Process and work-material variables were optimized...HPT vane material. Hastelloy X is a nickel-chromium superalloy used in high temperature sheet metal applications, such as combustion liners and

Calibration of GafChromic XR-RV3 radiochromic film for skin dose measurement using standardized x-ray spectra and a commercial flatbed scanner

PubMed Central

McCabe, Bradley P.; Speidel, Michael A.; Pike, Tina L.; Van Lysel, Michael S.

2011-01-01

Purpose: In this study, newly formulated XR-RV3 GafChromic® film was calibrated with National Institute of Standards and Technology (NIST) traceability for measurement of patient skin dose during fluoroscopically guided interventional procedures. Methods: The film was calibrated free-in-air to air kerma levels between 15 and 1100 cGy using four moderately filtered x-ray beam qualities (60, 80, 100, and 120 kVp). The calibration films were scanned with a commercial flatbed document scanner. Film reflective density-to-air kerma calibration curves were constructed for each beam quality, with both the orange and white sides facing the x-ray source. A method to correct for nonuniformity in scanner response (up to 25% depending on position) was developed to enable dose measurement with large films. The response of XR-RV3 film under patient backscattering conditions was examined using on-phantom film exposures and Monte Carlo simulations. Results: The response of XR-RV3 film to a given air kerma depended on kVp and film orientation. For a 200 cGy air kerma exposure with the orange side of the film facing the source, the film response increased by 20% from 60 to 120 kVp. At 500 cGy, the increase was 12%. When 500 cGy exposures were performed with the white side facing the x-ray source, the film response increased by 4.0% (60 kVp) to 9.9% (120 kVp) compared to the orange-facing orientation. On-phantom film measurements and Monte Carlo simulations show that using a NIST-traceable free-in-air calibration curve to determine air kerma in the presence of backscatter results in an error from 2% up to 8% depending on beam quality. The combined uncertainty in the air kerma measurement from the calibration curves and scanner nonuniformity correction was ±7.1% (95% C.I.). The film showed notable stability. Calibrations of film and scanner separated by 1 yr differed by 1.0%. Conclusions: XR-RV3 radiochromic film response to a given air kerma shows dependence on beam quality and film orientation. The presence of backscatter slightly modifies the x-ray energy spectrum; however, the increase in film response can be attributed primarily to the increase in total photon fluence at the sensitive layer. Film calibration curves created under free-in-air conditions may be used to measure dose from fluoroscopic quality x-ray beams, including patient backscatter with an error less than the uncertainty of the calibration in most cases. PMID:21626925

76 FR 18189 - Procurement List; Additions

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-01

...: Professional Contract Services, Inc., Austin, TX. Contracting Activity: Dept of the Army, XR W40M Natl Region Contract OFC, Washington, DC. Service Type/Location: Prime Vendor Support for Foreign Military Sales...

A Prospective Study of Bone Tumor Response Assessment in Metastatic Breast Cancer

PubMed Central

Hayashi, Naoki; Costelloe, Colleen M.; Hamaoka, Tsuyoshi; Wei, Caimiao; Niikura, Naoki; Theriault, Richard L.; Hortobagyi, Gabriel N.; Madewell, John E.; Ueno, Naoto T.

2013-01-01

In this pilot study, we prospectively compared the response of bone metastasis assessed by our MD Anderson (MDA) bone tumor response criteria (computed tomography [CT], plain radiography [XR], and skeletal scintigraphy [SS]) with the response assessed by the World Health Organization (WHO) criteria (XR and SS). Both MDA and WHO criteria predicted progression-free survival (PFS) of patients at 6 months but not at an earlier time point. Background In our previous study, new MD Anderson (MDA) bone tumor response criteria (based on computed tomography [CT], plain radiography [XR], and skeletal scintigraphy [SS]) predicted progression-free survival (PFS) better than did World Health Organization (WHO) bone tumor response criteria (plain radiography [XR] and SS) among patients with breast cancer and bone-only metastases. In this pilot study, we tested whether MDA criteria could reveal bone metastasis response earlier than WHO criteria in patients with newly diagnosed breast cancer with osseous and measurable nonosseous metastases. Methods We prospectively analyzed bone metastasis response using each imaging modality and set of bone response criteria to distinguish progressive disease (PD) from non-PD and their association with PFS and overall survival (OS). We also compared the response of osseous metastases assessed by both criteria with the response of nonosseous measurable lesions. Results The median follow-up period was 26.7 months (range, 6.1–53.3 months) in 29 patients. PFS rates differed at 6 months based on the classification of PD or non-PD using either set of criteria (MDA, P = .002; WHO, P = .014), but these rates, as well as OS, did not differ at 3 months. Response in osseous metastases by either set of criteria did not correlate with the response in nonosseous metastases. Conclusion MDA and WHO criteria predicted PFS of patients with osseous metastases at 6 months but not at an earlier time point. We plan a well-powered study to determine the role of MDA criteria in predicting bone tumor response by incorporating 18-fluorodeoxyglucose (18F) positron emission tomography (FDG-PET)/CT to see if findings using this modality are earlier than those with WHO criteria. PMID:23098575

Number needed to treat to harm for discontinuation due to adverse events in the treatment of bipolar depression, major depressive disorder, and generalized anxiety disorder with atypical antipsychotics.

PubMed

Gao, Keming; Kemp, David E; Fein, Elizabeth; Wang, Zuowei; Fang, Yiru; Ganocy, Stephen J; Calabrese, Joseph R

2011-08-01

To estimate the number needed to treat to harm (NNTH) for discontinuation due to adverse events with atypical antipsychotics relative to placebo during the treatment of bipolar depression, major depressive disorder (MDD), and generalized anxiety disorder (GAD). English-language literature published and cited in MEDLINE from January 1966 to May 2009 was searched with the terms antipsychotic, atypical antipsychotic, generic and brand names of atypical antipsychotics, safety, tolerability, discontinuation due to adverse events, somnolence, sedation, weight gain, akathisia, or extrapyramidal side effect; and bipolar depression, major depressive disorder, or generalized anxiety disorder; and randomized, placebo-controlled clinical trial. This search was augmented with a manual search. Studies with a cumulative sample of ≥ 100 patients were included. The NNTHs for discontinuation due to adverse events, somnolence, sedation, ≥ 7% weight gain, and akathisia relative to placebo were estimated with 95% confidence intervals to reflect the magnitude of variance. Five studies in bipolar depression, 10 studies in MDD, and 4 studies in GAD were identified. Aripiprazole and olanzapine have been studied in bipolar depression and refractory MDD. Only quetiapine extended release (quetiapine-XR) has been studied in 3 psychiatric conditions with different fixed dosing schedules. For aripiprazole, the mean NNTH for discontinuation due to adverse events was 14 in bipolar depression, but was not significantly different from placebo in MDD. For olanzapine, the mean NNTHs were 24 in bipolar depression and 9 in MDD. The risk for discontinuation due to adverse events during quetiapine-XR treatment appeared to be associated with dose. For quetiapine-XR 300 mg/d, the NNTHs for discontinuation due to adverse events were 9 for bipolar depression, 8 for refractory MDD, 9 for MDD, and 5 for GAD. At the same dose of quetiapine-XR, patients with GAD appeared to have a lower tolerability than those with bipolar depression or MDD. Due to flexible dosing, the risk for discontinuation due to adverse events in the treatment of bipolar depression, MDD, or GAD with other atypical antipsychotics could not be compared. © Copyright 2011 Physicians Postgraduate Press, Inc.

Women and Diabetes -- Diabetes Medicines

MedlinePlus

... insulin. Brand Name Other Name Januvia Sitagliptin Onglyza Saxagliptin Nesina Alogliptin Tradjenta Linagliptin Some Things To Think ... Sitagliptin and Metformin Kazano Alogliptin and Metformin Kombiglyze Saxagliptin and Metformin Kombiglyze XR (extended release) Saxagliptin and ...

Replacing Ag(TS)SCH(2)-R with Ag(TS)O(2)C-R in EGaIn-based tunneling junctions does not significantly change rates of charge transport.

PubMed

Liao, Kung-Ching; Yoon, Hyo Jae; Bowers, Carleen M; Simeone, Felice C; Whitesides, George M

2014-04-07

This paper compares rates of charge transport by tunneling across junctions with the structures Ag(TS) X(CH2 )2n CH3  //Ga2 O3  /EGaIn (n=1-8 and X= SCH2  and O2 C); here Ag(TS) is template-stripped silver, and EGaIn is the eutectic alloy of gallium and indium. Its objective was to compare the tunneling decay coefficient (β, Å(-1) ) and the injection current (J0 , A cm(-2) ) of the junctions comprising SAMs of n-alkanethiolates and n-alkanoates. Replacing Ag(TS) SCH2 -R with Ag(TS) O2 C-R (R=alkyl chains) had no significant influence on J0 (ca. 3×10(3)  A cm(-2) ) or β (0.75-0.79 Å(-1) )-an indication that such changes (both structural and electronic) in the Ag(TS) XR interface do not influence the rate of charge transport. A comparison of junctions comprising oligo(phenylene)carboxylates and n-alkanoates showed, as expected, that β for aliphatic (0.79 Å(-1) ) and aromatic (0.60 Å(-1) ) SAMs differed significantly. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Numerical considerations in the development and implementation of constitutive models

NASA Technical Reports Server (NTRS)

Haisler, W. E.; Imbrie, P. K.

1985-01-01

Several unified constitutive models were tested in uniaxial form by specifying input strain histories and comparing output stress histories. The purpose of the tests was to evaluate several time integration methods with regard to accuracy, stability, and computational economy. The sensitivity of the models to slight changes in input constants was also investigated. Results are presented for In100 at 1350 F and Hastelloy-X at 1800 F.

Integrated treatment approach improves cognitive function in demented and clinically depressed patients.

PubMed

Bragin, Valentin; Chemodanova, Marina; Dzhafarova, Narmina; Bragin, Ilya; Czerniawski, Jennifer L; Aliev, Gjumrakch

2005-01-01

The purpose of this study was to evaluate the efficacy of an integrative treatment approach on cognitive performance. The study sample comprised 35 medically ill patients (20 male, 15 female) with an average age of 71.05, who were diagnosed with mild dementia and depression. These patients were evaluated at baseline and at six, 12, and 24 months of treatment, which included antidepressants (sertraline, citalopram, or venlafaxine XR, alone or in combination with bupropion XR), cholinesterase inhibitors (donepezil, rivastigmine or galantamine), as well as vitamins and supplements (multivitamins, vitamin E, alpha-lipoic acid, omega-3 and coenzyme Q-10). Patients were encouraged to modify their diet and lifestyle and perform mild physical exercises. Results show that the integrative treatment not only protracted cognitive decline for 24 months but even improved cognition, especially memory and frontal lobe functions.

Library reuse in a rapid development environment

NASA Technical Reports Server (NTRS)

Uhde, JO; Weed, Daniel; Gottlieb, Robert; Neal, Douglas

1995-01-01

The Aeroscience and Flight Mechanics Division (AFMD) established a Rapid Development Laboratory (RDL) to investigate and improve new 'rapid development' software production processes and refine the use of commercial, off-the-shelf (COTS) tools. These tools and processes take an avionics design project from initial inception through high fidelity, real-time, hardware-in-the-loop (HIL) testing. One central theme of a rapid development process is the use and integration of a variety of COTS tools: This paper discusses the RDL MATRIX(sub x)(R) libraries, as well as the techniques for managing and documenting these libraries. This paper also shows the methods used for building simulations with the Advanced Simulation Development System (ASDS) libraries, and provides metrics to illustrate the amount of reuse for five complete simulations. Combining ASDS libraries with MATRIX(sub x)(R) libraries is discussed.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mendoza-Moctezuma, A. I.; Aguilar, J. Garcia; Garcia-Garduno, O. A.

Interventional cardiology procedures are an effective alternative for the reestablishment of correct sanguineous circulation in the heart. However, this kind of procedures exposes to the patients to a relatively high radiation doses. Usually, the surface peak skin dose is evaluated using a visual scale with a comparator strip, nevertheless, even if the comparator strip provides a simple and quick method for estimating the dose it has an uncertainty of {+-}25%. For this reason, a better evaluation method is needed. The objective of our project is to determine the surface peak skin dose of interventional cardiology procedures using GafChromic XR-RV2 filmmore » together with a commercial flatbed scanner in reflection mode. Here we report a protocol to handle GafChromic XR-RV2 film using a commercial flat bed scanner in reflection mode aiming at an uncertainty of {+-}3%.« less

Extended-release naltrexone for pre-release prisoners: A randomized trial of medical mobile treatment

PubMed Central

Gordon, Michael S.; Vocci, Frank J.; Fitzgerald, Terrence T.; O'Grady, Kevin E.; O'Brien, Charles P.

2017-01-01

Background Extended-release naltrexone (XR-NTX), is an effective treatment for opioid use disorder but is rarely initiated in US prisons or with criminal justice populations. Mobile treatment for chronic diseases have been implemented in a variety of settings. Mobile treatment may provide an opportunity to expand outreach to parolees to surmount barriers to traditional clinic treatment. Methods Male and female prisoners (240) with pre-incarceration histories of opioid use disorder who are within one month of release from prison will be enrolled in this randomized clinical trial. Participants are randomized to one of two study arms: 1) [XR-NTX-OTx] One injection of long-acting naltrexone in prison, followed by 6 monthly injections post-release at a community opioid treatment program; or 2) [XR-NTX+ MMTx] One injection of long-acting naltrexone in prison followed by 6 monthly injections post-release at the patient's place of residence utilizing mobile medical treatment. The primary outcomes are: treatment adherence; opioid use; criminal activity; re-arrest; reincarceration; and HIV risk-behaviors. Results We describe the background and rationale for the study, its aims, hypotheses, and study design. Conclusions The use of long-acting injectable naltrexone may be a promising form of treatment for pre-release prisoners. Finally, as many individuals in the criminal justice system drop out of treatment, this study will assess whether treatment at their place of residence will improve adherence and positively affect treatment outcomes. PMID:28011389

Extended-release naltrexone for pre-release prisoners: A randomized trial of medical mobile treatment.

PubMed

Gordon, Michael S; Vocci, Frank J; Fitzgerald, Terrence T; O'Grady, Kevin E; O'Brien, Charles P

2017-02-01

Extended-release naltrexone (XR-NTX), is an effective treatment for opioid use disorder but is rarely initiated in US prisons or with criminal justice populations. Mobile treatment for chronic diseases has been implemented in a variety of settings. Mobile treatment may provide an opportunity to expand outreach to parolees to surmount barriers to traditional clinic treatment. Male and female prisoners (240) with pre-incarceration histories of opioid use disorder who are within one month of release from prison will be enrolled in this randomized clinical trial. Participants are randomized to one of two study arms: 1) [XR-NTX-OTx] One injection of long-acting naltrexone in prison, followed by 6 monthly injections post-release at a community opioid treatment program; or 2) [XR-NTX+ MMTx] One injection of long-acting naltrexone in prison followed by 6 monthly injections post-release at the patient's place of residence utilizing mobile medical treatment. The primary outcomes are: treatment adherence; opioid use; criminal activity; re-arrest; reincarceration; and HIV risk-behaviors. We describe the background and rationale for the study, its aims, hypotheses, and study design. The use of long-acting injectable naltrexone may be a promising form of treatment for pre-release prisoners. Finally, as many individuals in the criminal justice system drop out of treatment, this study will assess whether treatment at their place of residence will improve adherence and positively affect treatment outcomes. ClinicalTrials.gov: NCT02867124. Copyright © 2016 Elsevier Inc. All rights reserved.

The SMS3D photovoltaic concentrator

NASA Astrophysics Data System (ADS)

Cvetković, Aleksandra; Hernandez, Maikel; Benítez, Pablo; Miñano, Juan Carlos; Schwartz, Joel; Plesniak, Adam; Jones, Russ; Whelan, David

2008-08-01

A novel photovoltaic concentrator is presented. The goal is to achieve high concentration design with high efficiency and high acceptance angle that in the same time is compact and convenient for thermal and mechanical management [1]. This photovoltaic system is based on 1 cm2 multi-junction tandem solar cells and an XR concentrator. The XR concentrator in this system is an SMS 3D design formed by one reflective (X) and one refractive (R) free-form surfaces (i.e., without rotational or linear symmetry) and has been chosen for its excellent aspect ratio and for its ability to perform near the thermodynamic limit. It is a mirror-lens device that has no shadowing elements and has square entry aperture (the whole system aperture area is used for collecting light). This large acceptance angle relaxes the manufacturing tolerances of all the optical and mechanical components of the system included the concentrator itself and is one of the keys to get a cost competitive photovoltaic generator. For the geometrical concentration of 1000x the simulation results show the acceptance angle of +/-1.8 deg. The irradiance distribution on the cell is achieved with ultra-short homogenizing prism, whose size is optimised to keep the maximum values under the ones that the cell can accept. The application of the XR optics to high-concentration is being developed in a consortium leaded by The Boeing Company, which has been awarded a project by US DOE in the framework of the Solar America Initiative.

Effect of magnesium oxide content on oxidation behavior of some superalloy-base cermets

NASA Technical Reports Server (NTRS)

Zaplatynsky, I.

1975-01-01

The effect of increasing magnesium oxide (MgO) content on the cyclic oxidation resistance of hot-pressed cermets of MgO in NiCrAlY, MgO in Hoskins-875, MgO in Inconel-702, and MgO in Hastelloy-X was investigated. The cermets with magnesium oxide levels of 5, 10, 20, and 40 vol percent were examined. The cyclic oxidation behavior of these cermets at 1100 and 1200 C in still air was determined by a thermogravimetric method supplemented by X-ray diffraction analysis and light and electron microscopy. In all instances, MgO prevented grain growth in the metallic phase. No evidence of oxidation along interphase boundaries was detected. Cermets of MgO in NiCrAlY and MgO in Hoskins-875 were superior to cermets of MgO in Inconel-702 and MgO in Hastelloy-X. Their oxidation resistance was degraded only when the MgO content was 40 vol percent. The oxidation behavior of MgO-in-Inconel-702 powder cermets containing 5- and 10-vol percent MgO was approximately similar to that of pure Inconel-702 compacts. The 20- and 40-vol percent MgO content reduced the oxidation resistance of MgO-in-Inconel-702 powder cermets relative to that of pure Inconel-702.

Additive Manufacturing of Fuel Injectors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sadek Tadros, Dr. Alber Alphonse; Ritter, Dr. George W.; Drews, Charles Donald

Additive manufacturing (AM), also known as 3D-printing, has been shifting from a novelty prototyping paradigm to a legitimate manufacturing tool capable of creating components for highly complex engineered products. An emerging AM technology for producing metal parts is the laser powder bed fusion (L-PBF) process; however, industry manufacturing specifications and component design practices for L-PBF have not yet been established. Solar Turbines Incorporated (Solar), an industrial gas turbine manufacturer, has been evaluating AM technology for development and production applications with the desire to enable accelerated product development cycle times, overall turbine efficiency improvements, and supply chain flexibility relative to conventionalmore » manufacturing processes (casting, brazing, welding). Accordingly, Solar teamed with EWI on a joint two-and-a-half-year project with the goal of developing a production L-PBF AM process capable of consistently producing high-nickel alloy material suitable for high temperature gas turbine engine fuel injector components. The project plan tasks were designed to understand the interaction of the process variables and their combined impact on the resultant AM material quality. The composition of the high-nickel alloy powders selected for this program met the conventional cast Hastelloy X compositional limits and were commercially available in different particle size distributions (PSD) from two suppliers. Solar produced all the test articles and both EWI and Solar shared responsibility for analyzing them. The effects of powder metal input stock, laser parameters, heat treatments, and post-finishing methods were evaluated. This process knowledge was then used to generate tensile, fatigue, and creep material properties data curves suitable for component design activities. The key process controls for ensuring consistent material properties were documented in AM powder and process specifications. The basic components of the project were: • Powder metal input stock: Powder characterization, dimensional accuracy, metallurgical characterization, and mechanical properties evaluation. • Process parameters: Laser parameter effects, post-printing heat-treatment development, mechanical properties evaluation, and post-finishing technique. • Material design curves: Room and elevated temperature tensiles, low cycle fatigue, and creep rupture properties curves generated. • AM specifications: Key metal powder characteristics, laser parameters, and heat-treatment controls identified.« less

Ditching Tests of a 1/24-Scale Model of the Lockheed XR60-1 Airplane, TED No. NACA 235

NASA Technical Reports Server (NTRS)

Fisher, Lloyd J.; Cederborg, Gibson A.

1948-01-01

The ditching characteristics of the Lockheed XR60-1 airplane were determined by tests of a 1/24-scale dynamic model in calm water at the Langley tank no. 2 monorail. Various landing attitudes, flap settings, speeds, and conditions of damager were investigated. The ditching behavior was evaluated from recordings of decelerations, length of runs, and motions of the model. Scale-strength bottoms and simulated crumpled bottoms were used to reproduce probable damage to the fuselage. It was concluded that the airplane should be ditched at a landing attitude of about 5 deg with flaps full down. At this attitude, the maximum longitudinal deceleration should not exceed 2g and the landing run will be bout three fuselage lengths. Damage to the fuselage will not be excessive and will be greatest near the point of initial contact with the water.

Zika virus produces noncoding RNAs using a multi-pseudoknot structure that confounds a cellular exonuclease

DOE PAGES

Akiyama, Benjamin M.; Laurence, Hannah M.; Massey, Aaron R.; ...

2016-11-10

The outbreak of Zika virus (ZIKV) and associated fetal microcephaly mandates efforts to understand the molecular processes of infection. Related flaviviruses produce noncoding subgenomic flaviviral RNAs (sfRNAs) that are linked to pathogenicity in fetal mice. These viruses make sfRNAs by co-opting a cellular exonuclease via structured RNAs called xrRNAs. We found that ZIKV-infected monkey and human epithelial cells, mouse neurons, and mosquito cells produce sfRNAs. The RNA structure that is responsible for ZIKV sfRNA production forms a complex fold that is likely found in many pathogenic flaviviruses. Mutations that disrupt the structure affect exonuclease resistance in vitro and sfRNA formationmore » during infection. The complete ZIKV xrRNA structure clarifies the mechanism of exonuclease resistance and identifies features that may modulate function in diverse flaviviruses.« less

Open-label pilot study of extended-release naltrexone to reduce drinking and driving among repeat offenders.

PubMed

Lapham, Sandra C; McMillan, Garnett P

2011-09-01

A high proportion of persons convicted of driving while impaired repeat the offense. Many continue drinking and driving, even when faced with long jail terms. Hence, they pose a serious public health threat. This preliminary study evaluated extended-release, injectable naltrexone suspension (XR-NTX) and supportive therapy in reducing (1) drinking and (2) attempts to drive after drinking among repeat driving while impaired offenders with an ignition interlock device installed in their vehicles. Treatment-seeking volunteers received medical management therapy and 3 monthly injections of XR-NTX. We compared data on alcohol consumption, alcohol biomarkers, and interlock information before, during, and after treatment using summary measures and Sign tests. Of 12 consented subjects, 10 received at least 1 injection, and 7 received all 3 injections. All subjects receiving medication reported a decrease in average drinks per day (P < 0.01) and abstinent days (P = 0.02) while on treatment versus pretreatment levels. Average daily drinks decreased by 77%, from 3.0 to 0.69 (P < 0.01), during treatment with XR-NTX. Average drinks per drinking day also declined by 39% during treatment, from 6.6 to 4.0 (P = 0.04). Percent days abstinent increased by 31%, from 56.8 to 81.96 (P = 0.02), which persisted after treatment completion. Biomarkers were consistent with reduced drinking. The percentage of vehicular failures to start due to elevated breath alcohol decreased from 3.1% of tests to 1.29% of tests. A randomized, controlled clinical trial is needed to demonstrate the efficacy of this promising treatment regimen for repeat offenders.

X-ray diffraction and reflectivity validation of the depletion attraction in the competitive adsorption of lung surfactant and albumin.

PubMed

Stenger, Patrick C; Wu, Guohui; Miller, Chad E; Chi, Eva Y; Frey, Shelli L; Lee, Ka Yee C; Majewski, Jaroslaw; Kjaer, Kristian; Zasadzinski, Joseph A

2009-08-05

Lung surfactant (LS) and albumin compete for the air-water interface when both are present in solution. Equilibrium favors LS because it has a lower equilibrium surface pressure, but the smaller albumin is kinetically favored by faster diffusion. Albumin at the interface creates an energy barrier to subsequent LS adsorption that can be overcome by the depletion attraction induced by polyethylene glycol (PEG) in solution. A combination of grazing incidence x-ray diffraction (GIXD), x-ray reflectivity (XR), and pressure-area isotherms provides molecular-resolution information on the location and configuration of LS, albumin, and polymer. XR shows an average electron density similar to that of albumin at low surface pressures, whereas GIXD shows a heterogeneous interface with coexisting LS and albumin domains at higher surface pressures. Albumin induces a slightly larger lattice spacing and greater molecular tilt, similar in effect to a small decrease in the surface pressure. XR shows that adding PEG to the LS-albumin subphase restores the characteristic LS electron density profile at the interface, and confirms that PEG is depleted near the interface. GIXD shows the same LS Bragg peaks and Bragg rods as on a pristine interface, but with a more compact lattice corresponding to a small increase in the surface pressure. These results confirm that albumin adsorption creates a physical barrier that inhibits LS adsorption, and that PEG in the subphase generates a depletion attraction between the LS aggregates and the interface that enhances LS adsorption without substantially altering the structure or properties of the LS monolayer.

RBAC-Matrix-based EMR right management system to improve HIPAA compliance.

PubMed

Lee, Hung-Chang; Chang, Shih-Hsin

2012-10-01

Security control of Electronic Medical Record (EMR) is a mechanism used to manage electronic medical records files and protect sensitive medical records document from information leakage. Researches proposed the Role-Based Access Control(RBAC). However, with the increasing scale of medical institutions, the access control behavior is difficult to have a detailed declaration among roles in RBAC. Furthermore, with the stringent specifications such as the U.S. HIPAA and Canada PIPEDA etc., patients are encouraged to have the right in regulating the access control of his EMR. In response to these problems, we propose an EMR digital rights management system, which is a RBAC-based extension to a matrix organization of medical institutions, known as RBAC-Matrix. With the aim of authorizing the EMR among roles in the organization, RBAC-Matrix also allow patients to be involved in defining access rights of his records. RBAC-Matrix authorizes access control declaration among matrix organizations of medical institutions by using XrML file in association with each EMR. It processes XrML rights declaration file-based authorization of behavior in the two-stage design, called master & servant stage, thus makes the associated EMR to be better protected. RBAC-Matrix will also make medical record file and its associated XrML declaration to two different EMRA(EMR Authorization)roles, namely, the medical records Document Creator (DC) and the medical records Document Right Setting (DRS). Access right setting, determined by the DRS, is cosigned by the patient, thus make the declaration of rights and the use of EMR to comply with HIPAA specifications.

Vibronic coupling effect on circular dichroism spectrum: Carotenoid-retinal interaction in xanthorhodopsin

NASA Astrophysics Data System (ADS)

Fujimoto, Kazuhiro J.; Balashov, Sergei P.

2017-03-01

The role of vibronic coupling of antenna carotenoid and retinal in xanthorhodopsin (XR) in its circular dichroism (CD) spectrum is examined computationally. A vibronic exciton model combined with a transition-density-fragment interaction (TDFI) method is developed, and applied to absorption and CD spectral calculations of XR. The TDFI method is based on the electronic Coulomb and exchange interactions between transition densities for individual chromophores [K. J. Fujimoto, J. Chem. Phys. 137, 034101 (2012)], which provides a quantitative description of electronic coupling energy. The TDFI calculation reveals a dominant contribution of the Coulomb interaction to the electronic coupling energy and a negligible contribution of the exchange interaction, indicating that the antenna function of carotenoid results from the Förster type of excitation-energy transfer, not from the Dexter one. The calculated absorption and CD spectra successfully reproduce the main features of the experimental results, which allow us to investigate the mechanism of biphasic CD spectrum observed in XR. The results indicate that vibronic coupling between carotenoid and retinal plays a significant role in the shape of the CD spectrum. Further analysis reveals that the negative value of electronic coupling directly contributes to the biphasic shape of CD spectrum. This study also reveals that the C6—C7 bond rotation of salinixanthin is not the main factor for the biphasic CD spectrum although it gives a non-negligible contribution to the spectral shift. The present method is useful for analyzing the molecular mechanisms underlying the chromophore-chromophore interactions in biological systems.

Accuracy of tracking forest machines with GPS

Treesearch

M.W. Veal; S.E. Taylor; T.P. McDonald; D.K. McLemore; M.R. Dunn

2001-01-01

This paper describes the results of a study that measured the accuracy of using GPS to track movement of forest machines. Two different commercially available GPS receivers (Trimble ProXR and GeoExplorer II) were used to track\\r\

Oxcarbazepine

MedlinePlus

... types of seizures in adults and children. Oxcarbazepine extended-release tablets (Oxtellar XR) are used in combination ... Oxcarbazepine comes as a tablet, an extended-release tablet, and a suspension (liquid) to take by mouth. The tablet and suspension are usually taken every 12 hours (twice a ...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rampado, O.; Garelli, E.; Ropolo, R.

Gafchromic XR-QA films were developed for patient dosimetry in diagnostic radiology. A possible application of these films is the measurement of doses in computed tomography. In this study a method to evaluate the CTDI using Gafchromic XR-QA film and a flatbed scanner was developed and tested. Film samples were cut to dimensions of 6x170 mm{sup 2} in order to have an integration area similar to that of a pencil ionization chamber, with the possibility of changing the integration length. Prior to exposing these films to a computed tomography beam, the angular dependence of the film dose response was investigated bymore » exposing film strips to a static x-ray beam at different angles in the range 0 deg. - 180 deg. A difference of 49% was found between the response with the axis beam parallel to the film surface (90 deg.) and with the axis beam perpendicular (0 deg. and 180 deg.). Integrating over a 360 deg. exposure like the one in computed tomography, a difference of less than 2% was estimated, which is comparable with the measurement error obtainable with XR-QA film. A calibration with a CT beam in the scout mode was performed and film strips were then exposed to single axial scans and to helical scans both in air and in phantoms. Two different types of flatbed scanners were used to read the film samples, a Microtek ScanMaker 9800XL scanner and an Epson Expression 10000 XL scanner, and the accuracy of the results were compared. For beam collimations above 10 mm differences between CTDI measured by film and CTDI measured by ionization chamber below 9% were found for the Epson scanner, with an average estimated error at 1 {sigma} level of 5%. For the Microtek scanner and for the same film samples, differences below 11% with an average error at 1 {sigma} level of 8% were founded. The 1 {sigma} uncertainty of the measured CTDI was provided by the method for each measurement, and it was shown that about the 95% of the differences between the CTDI measurements with radiochromic films and with the ionization chamber were below the estimated 2 {sigma} uncertainty, for both scanners. After an accurate calibration procedure and the consideration of the uncertainty associated with the measurement, Gafchromic XR-QA films can be used to evaluate the CTDI.« less

Along the Virtuality Continuum - Two Showcases on how xR Technologies Transform Geoscience Research and Education

NASA Astrophysics Data System (ADS)

Klippel, A.; Zhao, J.; Masrur, A.; Wallgruen, J. O.; La Femina, P. C.

2017-12-01

We present work along the virtuality continuum showcasing both AR and VR environments for geoscience applications and research. The AR/VR project focusses on one of the most prominent landmarks on the Penn State campus which, at the same time, is a representation of the geology of Pennsylvania. The Penn State Obelisk is a 32" high, 51 ton monument composed of 281 rocks collected from across Pennsylvania. While information about its origins and composition are scattered in articles and some web databases, we compiled all the available data from the web and archives and curated them as a basis for an immersive xR experience. Tabular data was amended by xR data such as 360° photos, videos, and 3D models (e.g., the Obelisk). Our xR (both AR and VR) prototype provides an immersive analytical environment that supports interactive data visualization and virtual navigation in a natural environment (a campus model of today and of 1896, the year of the Obelisk's installation). This work-in-progress project can provide an interactive immersive learning platform (specifically, for K-12 and introductory level geosciences students) where learning process is enhanced through seamless navigation between 3D data space and physical space. The, second, VR focused application is creating and empirically evaluating virtual reality (VR) experiences for geosciences research, specifically, an interactive volcano experience based on LiDAR and image data of Iceland's Thrihnukar volcano. The prototype addresses the lack of content and tools for immersive virtual reality (iVR) in geoscientific education and research and how to make it easier to integrate iVR into research and classroom experiences. It makes use of environmentally sensed data such that interaction and linked content can be integrated into a single experience. We discuss our workflows as well as methods and authoring tools for iVR analysis and creation of virtual experiences. These methods and tools aim to enhance the utility of geospatial data from repositories such as OpenTopography.org through unlocking treasure-troves of geospatial data for VR applications. Their enhanced accessibility in education and research for the geosciences and beyond will benefit geoscientists and educators who cannot be expected to be VR and 3D application experts.

Determination of the relative resistance to ignition of selected turbopump materials in high-pressure, high-temperature, oxygen environments, volume 3

NASA Technical Reports Server (NTRS)

Stoltzfus, Joel M.; Benz, Frank J.

1986-01-01

Data is presented from frictional heating tests on pairs of different materials. Materials tested include: Hastelloy X, Inconel 600, Invar 36, Monel K-500, Monel 400, nickel 200, silicon carbide, stainless steels 316, and zirconium copper. In tests where pairs of different materials were rubbed together, the material rated less resistant to ignition in previous tests appeared to control the resistance to ignition of the pair.

Effect of Continuous and Pulsed Current Gas Tungsten Arc Welding on Dissimilar Weldments Between Hastelloy C-276/AISI 321 Austenitic Stainless Steel

NASA Astrophysics Data System (ADS)

Sharma, Sumitra; Taiwade, Ravindra V.; Vashishtha, Himanshu

2017-03-01

In the present investigation, an attempt has been made to join Hastelloy C-276 nickel-based superalloy and AISI 321 austenitic stainless steel using ERNiCrMo-4 filler. The joints were fabricated by continuous and pulsed current gas tungsten arc welding processes. Experimental studies to ascertain the structure-property co-relationship with or without pulsed current mode were carried out using an optical microscope and scanning electron microscope. Further, the energy-dispersive spectroscope was used to evaluate the extent of microsegregation. The microstructure of fusion zone was obtained as finer cellular dendritic structure for pulsed current mode, whereas columnar structure was formed with small amount of cellular structure for continuous current mode. The scanning electron microscope examination witnessed the existence of migrated grain boundaries at the weld interfaces. Moreover, the presence of secondary phases such as P and μ was observed in continuous current weld joints, whereas they were absent in pulsed current weld joints, which needs to be further characterized. Moreover, pulsed current joints resulted in narrower weld bead, refined morphology, reduced elemental segregation and improved strength of the welded joints. The outcomes of the present investigation would help in obtaining good quality dissimilar joints for industrial applications and AISI 321 ASS being cheaper consequently led to cost-effective design also.

Compatibility studies of metallic materials with lithium-based oxides

NASA Astrophysics Data System (ADS)

Hofmann, P.; Dienst, W.

1988-07-01

The compatibility of Li 2O, Li 4SiO 4 and Li 2SiO 3 with the cladding materials AISI 316, 1.4914, Hastelloy X and Inconel 625 was investigated at 800-1000°C for annealing times up to 1000 h. A controlled oxygen reactivity was established by adding 1 mol% NiO per mole Li 2O to the Li-based oxides. In addition, some compatibility tests were performed at 600-900°C on Be, which is of interest as a neutron multiplier material, with Li 2SiO 3 as well as AISI 316. Li 2O accounted for the strongest cladding attack, followed by Li 4SiO 4 and Li 2SiO 3. In the absence of NiO, Li 2SiO 3 caused no chemical interactions at all. With respect to the cladding materials, there was no considerable difference in the reaction rates of AISI 316, Hastelloy X and Inconel 625. However, the steel 1.4914 was clearly more heavily attacked at and above 800°C. The compatibility of Be with Li 2SiO 3 or AISI 316 seems to be tolerable up to about 650°C. At higher temperatures a liquid Li suicide phase is formed which results in strong local attack and penetration into Li 2SiO 3.

X-Ray Spectrometry of Galactic Sources Seen from the Southern Hemisphere.

DTIC Science & Technology

investigation on glactic X-rays was centered in one experiment carried out in Argentina in November 26, 1969. A balloon-borne equipment was launched in order to detect the X rays from the Centaurus XR-4 source. (Author)

75 FR 58352 - Marine Mammals; File No. 14535

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-24

... DEPARTMENT OF COMMERCE National Oceanic and Atmospheric Administration RIN 0648-XR61 Marine Mammals; File No. 14535 AGENCY: National Marine Fisheries Service (NMFS), National Oceanic and Atmospheric... Education Division, Office of Protected Resources, National Marine Fisheries Service. [FR Doc. 2010-24040...

Extended-release metformin does not reduce the clomiphene citrate dose required to induce ovulation in polycystic ovary syndrome.

PubMed

Cataldo, Nicholas A; Barnhart, Huiman X; Legro, Richard S; Myers, Evan R; Schlaff, William D; Carr, Bruce R; Diamond, Michael P; Carson, Sandra A; Steinkampf, Michael P; Coutifaris, Christos; McGovern, Peter G; Gosman, Gabriella; Nestler, John E; Giudice, Linda C

2008-08-01

When used for ovulation induction, higher doses of clomiphene may lead to antiestrogenic side effects that reduce fecundity. It has been suggested that metformin in combination with clomiphene can restore ovulation to some clomiphene-resistant anovulators with polycystic ovary syndrome (PCOS). Our objective was to determine if cotreatment with extended-release metformin (metformin XR) can lower the threshold dose of clomiphene needed to induce ovulation in women with PCOS. A secondary analysis of data from the National Institute of Child Health and Human Development Cooperative Multicenter Reproductive Medicine Network prospective, double-blind, placebo-controlled multicenter clinical trial, Pregnancy in Polycystic Ovary Syndrome, was performed. Study volunteers at multiple academic medical centers were included. Women with PCOS and elevated serum testosterone who were randomized to clomiphene alone or with metformin (n = 209 in each group) were included in the study. Clomiphene citrate, 50 mg daily for 5 d, was increased to 100 and 150 mg in subsequent cycles if ovulation was not achieved; half also received metformin XR, 1000 mg twice daily. Treatment was for up to 30 wk or six cycles, or until first pregnancy. Ovulation was confirmed by a serum progesterone more than or equal to 5 ng/ml, drawn prospectively every 1-2 wk. The overall prevalence of at least one ovulation after clomiphene was 75 and 83% (P = 0.04) for the clomiphene-only and clomiphene plus metformin groups, respectively. Using available data from 314 ovulators, the frequency distribution of the lowest clomiphene dose (50, 100, or 150 mg daily) resulting in ovulation was indistinguishable between the two treatment groups. Metformin XR does not reduce the lowest dose of clomiphene that induces ovulation in women with PCOS.

The effect of pH, buffer capacity and ionic strength on quetiapine fumarate release from matrix tablets prepared using two different polymeric blends.

PubMed

Hamed, Rania; AlJanabi, Reem; Sunoqrot, Suhair; Abbas, Aiman

2017-08-01

The objective of this study was to investigate the effect of the different physiological parameters of the gastrointestinal (GI) fluid (pH, buffer capacity, and ionic strength) on the in vitro release of the weakly basic BCS class II drug quetiapine fumarate (QF) from two once-a-day matrix tablet formulations (F1 and F2) developed as potential generic equivalents to Seroquel ® XR. F1 tablets were prepared using blends of high and low viscosity grades of hydroxypropyl methylcellulose (HPMC K4M and K100LV, respectively), while F2 tablets were prepared from HPMC K4M and PEGylated glyceryl behenate (Compritol ® HD5 ATO). The two formulations attained release profiles of QF over 24 h similar to that of Seroquel ® XR using the dissolution medium published by the Food and Drug Administration (FDA). A series of solubility and in vitro dissolution studies was then carried out using media that simulate the gastric and intestinal fluids and cover the physiological pH, buffer capacity and ionic strength range of the GIT. Solubility studies revealed that QF exhibits a typical weak base pH-dependent solubility profile and that the solubility of QF increases with increasing the buffer capacity and ionic strength of the media. The release profiles of QF from F1, F2 and Seroquel ® XR tablets were found to be influenced by the pH, buffer capacity and ionic strength of the dissolution media to varying degrees. Results highlight the importance of studying the physiological variables along the GIT in designing controlled release formulations for more predictive in vitro-in vivo correlations.

Probing interfacial reactions with x-ray reflectivity and x-ray reflection interface microscopy : influence of NaCl on the dissolution of orthoclase at pOH2 and 85 {degree} C.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fenter, P.; Lee, S. S.; Park, C.

2010-01-01

The role of electrolyte ions in the dissolution of orthoclase (0 0 1) in 0.01 m NaOH (pOH {approx} 2) at 84 {+-} 1 C is studied using a combination of in-situ X-ray reflectivity (XR) and ex-situ X-ray reflection interface microscopy (XRIM). The real-time XR measurements show characteristic intensity oscillations as a function of time indicative of the successive removal of individual layers. The dissolution rate in 0.01 m NaOH increases approximately linearly with increasing NaCl concentration up to 2 m NaCl. XRIM measurements of the lateral interfacial topography/structure were made for unreacted surfaces and those reacted in 0.01 mmore » NaOH/1.0 m NaCl solution for 15, 30 and 58 min. The XRIM images reveal that the dissolution reaction leads to the formation of micron-scale regions that are characterized by intrinsically lower reflectivity than the unreacted regions, and appears to be nucleated at steps and defect sites. The reflectivity signal from these reacted regions in the presence of NaCl in solution is significantly lower than that calculated from an idealized layer-by-layer dissolution process, as observed previously in 0.1 m NaOH in the absence of added electrolyte. This difference suggests that dissolved NaCl results in a higher terrace reactivity leading to a more three-dimensional process, consistent with the real-time XR measurements. These observations demonstrate the feasibility of XRIM to gain new insights into processes that control interfacial reactivity, specifically the role of electrolytes in feldspar dissolution at alkaline conditions.« less

Inhibition of the purinergic pathway prolongs mouse lung allograft survival.

PubMed

Liu, Kaifeng; Vergani, Andrea; Zhao, Picheng; Ben Nasr, Moufida; Wu, Xiao; Iken, Khadija; Jiang, Dawei; Su, Xiaofeng; Fotino, Carmen; Fiorina, Paolo; Visner, Gary A

2014-08-01

Lung transplantation has limited survival with current immunosuppression. ATP is released from activated T cells, which act as costimulatory molecules through binding to the purinergic receptor P2XR7. We investigated the role of blocking the ATP/purinergic pathway, primarily P2XR7, using its inhibitor oxidized ATP (oATP) in modulating rejection of mouse lung allografts. Mouse lung transplants were performed using mice with major histocompatibility complex mismatch, BALB/c to C57BL6. Recipients received suramin or oATP, and lung allografts were evaluated 15 to ≥ 60 days after transplantation. Recipients were also treated with oATP after the onset of moderate to severe rejection to determine its ability to rescue lung allografts. Outcomes measures included lung function, histology, thoracic imaging, and allo-immune responses. Blocking purinergic receptors with the nonselective inhibitor suramin or with the P2XR7-selective inhibitor oATP reduced acute rejection and prolonged lung allograft survival for ≥ 60 days with no progression in severity. There were fewer inflammatory cells within lung allografts, less rejection, and improved lung function, which was maintained over time. CD4 and CD8 T cells were reduced within lung allografts with impaired activation with prolonged impairment of CD8 responses. In vitro, oATP reduced CD8 activation of Th1 inflammatory cytokines IFN-γ and TNF-α and cytolytic machinery, granzyme B. Cotreatment with immunosuppressive agents, cyclosporine, rapamycin, or CTLA-4Ig resulted in no additive benefits, and oATP alone resulted in better outcomes than cyclosporine alone. This study illustrates a potential new pathway to target in hopes of prolonging survival of lung transplant recipients.

Utility of event-related potentials in predicting antidepressant treatment response: An iSPOT-D report.

PubMed

van Dinteren, Rik; Arns, Martijn; Kenemans, Leon; Jongsma, Marijtje L A; Kessels, Roy P C; Fitzgerald, Paul; Fallahpour, Kamran; Debattista, Charles; Gordon, Evian; Williams, Leanne M

2015-11-01

It is essential to improve antidepressant treatment of major depressive disorder (MDD) and one way this could be achieved is by reducing the number of treatment steps by employing biomarkers that can predict treatment outcome. This study investigated differences between MDD patients and healthy controls in the P3 and N1 component from the event-related potential (ERP) generated in a standard two-tone oddball paradigm. Furthermore, the P3 and N1 are investigated as predictors for treatment outcome to three different antidepressants. In the international Study to Predict Optimized Treatment in Depression (iSPOT-D)--a multi-center, international, randomized, prospective practical trial--1008 MDD participants were randomized to escitalopram, sertraline or venlafaxine-XR. The study also recruited 336 healthy controls. Treatment response and remission were established after eight weeks using the 17-item Hamilton Rating Scale for Depression. P3 and N1 latencies and amplitudes were analyzed using a peak-picking approach and further replicated by using exact low resolution tomography (eLORETA). A reduced P3 was found in MDD patients compared to controls by a peak-picking analysis. This was validated in a temporal global field power analysis. Source density analysis revealed that the difference in cortical activity originated from the posterior cingulate and parahippocampal gyrus. Male non-responders to venlafaxine-XR had significantly smaller N1 amplitudes than responders. This was demonstrated by both analytical methods. Male non-responders to venlafaxine-XR had less activity originating from the left insular cortex. The observed results are discussed from a neural network viewpoint. Copyright © 2015 Elsevier B.V. and ECNP. All rights reserved.

Molecular Dynamics Simulation of the Complex PBP-2x with Drug Cefuroxime to Explore the Drug Resistance Mechanism of Streptococcus suis R61

PubMed Central

Xia, Yingjie; Yang, Ming; Xiao, Jingfa; Yu, Jun

2012-01-01

Drug resistance of Streptococcus suis strains is a worldwide problem for both humans and pigs. Previous studies have noted that penicillin-binding protein (PBPs) mutation is one important cause of β-lactam antibiotic resistance. In this study, we used the molecular dynamics (MD) method to study the interaction differences between cefuroxime (CES) and PBP2x within two newly sequenced Streptococcus suis: drug-sensitive strain A7, and drug-resistant strain R61. The MM-PBSA results proved that the drug bound much more tightly to PBP2x in A7 (PBP2x-A7) than to PBP2x in R61 (PBP2x-R61). This is consistent with the evidently different resistances of the two strains to cefuroxime. Hydrogen bond analysis indicated that PBP2x-A7 preferred to bind to cefuroxime rather than to PBP2x-R61. Three stable hydrogen bonds were formed by the drug and PBP2x-A7, while only one unstable bond existed between the drug and PBP2x-R61. Further, we found that the Gln569, Tyr594, and Gly596 residues were the key mutant residues contributing directly to the different binding by pair wise energy decomposition comparison. By investigating the binding mode of the drug, we found that mutant residues Ala320, Gln553, and Thr595 indirectly affected the final phenomenon by topological conformation alteration. Above all, our results revealed some details about the specific interaction between the two PBP2x proteins and the drug cefuroxime. To some degree, this explained the drug resistance mechanism of Streptococcus suis and as a result could be helpful for further drug design or improvement. PMID:22563422

Molecular dynamics simulation of the complex PBP-2x with drug cefuroxime to explore the drug resistance mechanism of Streptococcus suis R61.

PubMed

Ge, Yan; Wu, Jiayan; Xia, Yingjie; Yang, Ming; Xiao, Jingfa; Yu, Jun

2012-01-01

Drug resistance of Streptococcus suis strains is a worldwide problem for both humans and pigs. Previous studies have noted that penicillin-binding protein (PBPs) mutation is one important cause of β-lactam antibiotic resistance. In this study, we used the molecular dynamics (MD) method to study the interaction differences between cefuroxime (CES) and PBP2x within two newly sequenced Streptococcus suis: drug-sensitive strain A7, and drug-resistant strain R61. The MM-PBSA results proved that the drug bound much more tightly to PBP2x in A7 (PBP2x-A7) than to PBP2x in R61 (PBP2x-R61). This is consistent with the evidently different resistances of the two strains to cefuroxime. Hydrogen bond analysis indicated that PBP2x-A7 preferred to bind to cefuroxime rather than to PBP2x-R61. Three stable hydrogen bonds were formed by the drug and PBP2x-A7, while only one unstable bond existed between the drug and PBP2x-R61. Further, we found that the Gln569, Tyr594, and Gly596 residues were the key mutant residues contributing directly to the different binding by pair wise energy decomposition comparison. By investigating the binding mode of the drug, we found that mutant residues Ala320, Gln553, and Thr595 indirectly affected the final phenomenon by topological conformation alteration. Above all, our results revealed some details about the specific interaction between the two PBP2x proteins and the drug cefuroxime. To some degree, this explained the drug resistance mechanism of Streptococcus suis and as a result could be helpful for further drug design or improvement.

Deletion of FPS1, Encoding Aquaglyceroporin Fps1p, Improves Xylose Fermentation by Engineered Saccharomyces cerevisiae

PubMed Central

Wei, Na; Xu, Haiqing; Kim, Soo Rin

2013-01-01

Accumulation of xylitol in xylose fermentation with engineered Saccharomyces cerevisiae presents a major problem that hampers economically feasible production of biofuels from cellulosic plant biomass. In particular, substantial production of xylitol due to unbalanced redox cofactor usage by xylose reductase (XR) and xylitol dehydrogenase (XDH) leads to low yields of ethanol. While previous research focused on manipulating intracellular enzymatic reactions to improve xylose metabolism, this study demonstrated a new strategy to reduce xylitol formation and increase carbon flux toward target products by controlling the process of xylitol secretion. Using xylitol-producing S. cerevisiae strains expressing XR only, we determined the role of aquaglyceroporin Fps1p in xylitol export by characterizing extracellular and intracellular xylitol. In addition, when FPS1 was deleted in a poorly xylose-fermenting strain with unbalanced XR and XDH activities, the xylitol yield was decreased by 71% and the ethanol yield was substantially increased by nearly four times. Experiments with our optimized xylose-fermenting strain also showed that FPS1 deletion reduced xylitol production by 21% to 30% and increased ethanol yields by 3% to 10% under various fermentation conditions. Deletion of FPS1 decreased the xylose consumption rate under anaerobic conditions, but the effect was not significant in fermentation at high cell density. Deletion of FPS1 resulted in higher intracellular xylitol concentrations but did not significantly change the intracellular NAD+/NADH ratio in xylose-fermenting strains. The results demonstrate that Fps1p is involved in xylitol export in S. cerevisiae and present a new gene deletion target, FPS1, and a mechanism different from those previously reported to engineer yeast for improved xylose fermentation. PMID:23475614

Enhanced xylose fermentation by engineered yeast expressing NADH oxidase through high cell density inoculums.

PubMed

Zhang, Guo-Chang; Turner, Timothy L; Jin, Yong-Su

2017-03-01

Accumulation of reduced byproducts such as glycerol and xylitol during xylose fermentation by engineered Saccharomyces cerevisiae hampers the economic production of biofuels and chemicals from cellulosic hydrolysates. In particular, engineered S. cerevisiae expressing NADPH-linked xylose reductase (XR) and NAD + -linked xylitol dehydrogenase (XDH) produces substantial amounts of the reduced byproducts under anaerobic conditions due to the cofactor difference of XR and XDH. While the additional expression of a water-forming NADH oxidase (NoxE) from Lactococcus lactis in engineered S. cerevisiae with the XR/XDH pathway led to reduced glycerol and xylitol production and increased ethanol yields from xylose, volumetric ethanol productivities by the engineered yeast decreased because of growth defects from the overexpression of noxE. In this study, we introduced noxE into an engineered yeast strain (SR8) exhibiting near-optimal xylose fermentation capacity. To overcome the growth defect caused by the overexpression of noxE, we used a high cell density inoculum for xylose fermentation by the SR8 expressing noxE. The resulting strain, SR8N, not only showed a higher ethanol yield and lower byproduct yields, but also exhibited a high ethanol productivity during xylose fermentation. As noxE overexpression elicits a negligible growth defect on glucose conditions, the beneficial effects of noxE overexpression were substantial when a mixture of glucose and xylose was used. Consumption of glucose led to rapid cell growth and therefore enhanced the subsequent xylose fermentation. As a result, the SR8N strain produced more ethanol and fewer byproducts from a mixture of glucose and xylose than the parental SR8 strain without noxE overexpression. Our results suggest that the growth defects from noxE overexpression can be overcome in the case of fermenting lignocellulose-derived sugars such as glucose and xylose.

The yeast Scheffersomyces amazonensis is an efficient xylitol producer.

PubMed

Cadete, Raquel M; Melo-Cheab, Monaliza A; Viana, Adriana L; Oliveira, Evelyn S; Fonseca, César; Rosa, Carlos A

2016-12-01

This study assessed the efficiency of Scheffersomyces amazonensis UFMG-CM-Y493 T , cultured in xylose-supplemented medium (YPX) and rice hull hydrolysate (RHH), to convert xylose to xylitol under moderate and severe oxygen limitation. The highest xylitol yields of 0.75 and 1.04 g g -1 in YPX and RHH, respectively, were obtained under severe oxygen limitation. However, volumetric productivity in RHH was ninefold decrease than that in YPX medium. The xylose reductase (XR) and xylitol dehydrogenase (XDH) activities in the YPX cultures were strictly dependent on NADPH and NAD + respectively, and were approximately 10% higher under severe oxygen limitation than under moderate oxygen limitation. This higher xylitol production observed under severe oxygen limitation can be attributed to the higher XR activity and shortage of the NAD + needed by XDH. These results suggest that Sc. amazonensis UFMG-CM-Y493 T is one of the greatest xylitol producers described to date and reveal its potential use in the biotechnological production of xylitol.

Streptococcus mutans: Fructose Transport, Xylitol Resistance, and Virulence

PubMed Central

Tanzer, J.M.; Thompson, A.; Wen, Z.T.; Burne, R.A.

2008-01-01

Streptococcus mutans, the primary etiological agent of human dental caries, possesses at least two fructose phosphotransferase systems (PTSs), encoded by fruI and fruCD. fruI is also responsible for xylitol transport. We hypothesized that fructose and xylitol transport systems do not affect virulence. Thus, colonization and cariogenicity of fruI− and fruCD− single and double mutants, their WT (UA159), and xylitol resistance (Xr) of S. mutans were studied in rats fed a high-sucrose diet. A sucrose phosphorylase (gtfA−) mutant and a reference strain (NCTC-10449S) were additional controls. Recoveries of fruI mutant from the teeth were decreased, unlike those for the other strains. The fruCD mutation was associated with a slight loss of cariogenicity on enamel, whereas mutation of fruI was associated with a loss of cariogenicity in dentin. These results also suggest why xylitol inhibition of caries is paradoxically associated with spontaneous emergence of so-called Xr S. mutans in habitual human xylitol users. PMID:16567561

A strain of Saccharomyces cerevisiae evolved for fermentation of lignocellulosic biomass displays improved growth and fermentative ability in high solids concentrations and in the presence of inhibitory compounds

PubMed Central

2011-01-01

Background Softwoods are the dominant source of lignocellulosic biomass in the northern hemisphere, and have been investigated worldwide as a renewable substrate for cellulosic ethanol production. One challenge to using softwoods, which is particularly acute with pine, is that the pretreatment process produces inhibitory compounds detrimental to the growth and metabolic activity of fermenting organisms. To overcome the challenge of bioconversion in the presence of inhibitory compounds, especially at high solids loading, a strain of Saccharomyces cerevisiae was subjected to evolutionary engineering and adaptation for fermentation of pretreated pine wood (Pinus taeda). Results An industrial strain of Saccharomyces, XR122N, was evolved using pretreated pine; the resulting daughter strain, AJP50, produced ethanol much more rapidly than its parent in fermentations of pretreated pine. Adaptation, by preculturing of the industrial yeast XR122N and the evolved strains in 7% dry weight per volume (w/v) pretreated pine solids prior to inoculation into higher solids concentrations, improved fermentation performance of all strains compared with direct inoculation into high solids. Growth comparisons between XR122N and AJP50 in model hydrolysate media containing inhibitory compounds found in pretreated biomass showed that AJP50 exited lag phase faster under all conditions tested. This was due, in part, to the ability of AJP50 to rapidly convert furfural and hydroxymethylfurfural to their less toxic alcohol derivatives, and to recover from reactive oxygen species damage more quickly than XR122N. Under industrially relevant conditions of 17.5% w/v pretreated pine solids loading, additional evolutionary engineering was required to decrease the pronounced lag phase. Using a combination of adaptation by inoculation first into a solids loading of 7% w/v for 24 hours, followed by a 10% v/v inoculum (approximately equivalent to 1 g/L dry cell weight) into 17.5% w/v solids, the final strain (AJP50) produced ethanol at more than 80% of the maximum theoretical yield after 72 hours of fermentation, and reached more than 90% of the maximum theoretical yield after 120 hours of fermentation. Conclusions Our results show that fermentation of pretreated pine containing liquid and solids, including any inhibitory compounds generated during pretreatment, is possible at higher solids loadings than those previously reported in the literature. Using our evolved strain, efficient fermentation with reduced inoculum sizes and shortened process times was possible, thereby improving the overall economic viability of a woody biomass-to-ethanol conversion process. PMID:22074982

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCabe, Bradley P.; Speidel, Michael A.; Pike, Tina L.

Purpose: In this study, newly formulated XR-RV3 GafChromic film was calibrated with National Institute of Standards and Technology (NIST) traceability for measurement of patient skin dose during fluoroscopically guided interventional procedures. Methods: The film was calibrated free-in-air to air kerma levels between 15 and 1100 cGy using four moderately filtered x-ray beam qualities (60, 80, 100, and 120 kVp). The calibration films were scanned with a commercial flatbed document scanner. Film reflective density-to-air kerma calibration curves were constructed for each beam quality, with both the orange and white sides facing the x-ray source. A method to correct for nonuniformity inmore » scanner response (up to 25% depending on position) was developed to enable dose measurement with large films. The response of XR-RV3 film under patient backscattering conditions was examined using on-phantom film exposures and Monte Carlo simulations. Results: The response of XR-RV3 film to a given air kerma depended on kVp and film orientation. For a 200 cGy air kerma exposure with the orange side of the film facing the source, the film response increased by 20% from 60 to 120 kVp. At 500 cGy, the increase was 12%. When 500 cGy exposures were performed with the white side facing the x-ray source, the film response increased by 4.0% (60 kVp) to 9.9% (120 kVp) compared to the orange-facing orientation. On-phantom film measurements and Monte Carlo simulations show that using a NIST-traceable free-in-air calibration curve to determine air kerma in the presence of backscatter results in an error from 2% up to 8% depending on beam quality. The combined uncertainty in the air kerma measurement from the calibration curves and scanner nonuniformity correction was {+-}7.1% (95% C.I.). The film showed notable stability. Calibrations of film and scanner separated by 1 yr differed by 1.0%. Conclusions: XR-RV3 radiochromic film response to a given air kerma shows dependence on beam quality and film orientation. The presence of backscatter slightly modifies the x-ray energy spectrum; however, the increase in film response can be attributed primarily to the increase in total photon fluence at the sensitive layer. Film calibration curves created under free-in-air conditions may be used to measure dose from fluoroscopic quality x-ray beams, including patient backscatter with an error less than the uncertainty of the calibration in most cases.« less

78 FR 57904 - Request for a License To Export; Reactor Components

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-20

... NUCLEAR REGULATORY COMMISSION Request for a License To Export; Reactor Components Pursuant to 10..., systems, related reactors. operation of AP- XR177, 11006121. equipment, and 1000 (design) spare parts. nuclear reactors. Dated this 16th day of September 2013 in Rockville, Maryland. For The Nuclear Regulatory...

77 FR 39521 - Application for a License To Export Nuclear Reactor Major Components and Equipment

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-03

... LLC reactor coolant equipment for four constructing four plant May 14, 2012 pumps with motors, APR1400... Emirates. XR176 monitoring and plant in Braka. 110060011 control equipment, auxiliary equipment and... NUCLEAR REGULATORY COMMISSION Application for a License To Export Nuclear Reactor Major Components...

75 FR 10216 - Marine Mammals; File No. 358-1787

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-05

... DEPARTMENT OF COMMERCE National Oceanic and Atmospheric Administration RIN 0648-XR83 Marine Mammals; File No. 358-1787 AGENCY: National Marine Fisheries Service (NMFS), National Oceanic and... Resources, National Marine Fisheries Service. [FR Doc. 2010-4683 Filed 3-4-10; 8:45 am] BILLING CODE 3510-22...

Thermal-mechanical fatigue behavior of nickel-base superalloys

NASA Technical Reports Server (NTRS)

Pelloux, R. M.; Marchand, N.

1986-01-01

The main achievements of a 36-month research program are presented. The main objective was to gain more insight into the problem of crack growth under thermal mechanical fatigue (TMF) conditions. This program was conducted at M.I.T. for the period of September 1982 to September 1985. The program was arranged into five technical tasks. Under Task I, the literature of TMF data was reviewed. The goal was to identify the crack propagation conditions in aircraft engines (hot section) and to assess the validity of conventional fracture mechanics parameters to address TMF crack growth. The second task defined the test facilities, test specimen and the testing conditions needed to establish the effectiveness of data correlation parameters identified in Task I. Three materials (Inconel X-750, Hastelloy-X, and B-1900) were chosen for the program. Task II was accomplished in collaboration with Pratt & Whitney Aircraft engineers. Under Task III, a computerized testing system to measure the TMF behavior (LCF and CG behaviors) of various alloys systems was built. The software used to run isothermal and TMF tests was also developed. Built around a conventional servohydraulic machine, the system is capable of push-pull tests under stress or strain and temperature controlled conditions in the temperature range of 25C to 1050C. A crack propagation test program was defined and conducted under Task IV. The test variables included strain range, strain rate (frequency) and temperature. Task V correlated and generalized the Task IV data for isothermal and variable temperature conditions so that several crack propagation parameters could be compared and evaluated. The structural damage (mode of cracking and dislocation substructure) under TMF cycling was identified and contrasted with the isothermal damage to achieve a sound fundamental mechanistic understanding of TMF.

Thermostructural applications of heat pipes

NASA Technical Reports Server (NTRS)

Peeples, M. E.; Reeder, J. C.; Sontag, K. E.

1979-01-01

The feasibility of integrating heat pipes in high temperature structure to reduce local hot spot temperature was evaluated for a variety of hypersonic aerospace vehicles. From an initial list of twenty-two potential applications, the single stage to orbit wing leading edge showed the greatest promise and was selected for preliminary design of an integrated heat pipe thermostructural system. The design consisted of a Hastelloy X assembly with sodium heat pipe passages aligned normal to the wing leading edge. A d-shaped heat pipe cross section was determined to be optimum from the standpoint of structural weight.

A Formal Foundation for XrML

DTIC Science & Technology

2008-02-01

grants g, we ab - breviate the condition Said(Alice,Perm(Alice, issue,Perm(Alice, issue, g))) as d(g) and we abbreviate the grant Perm(Alice, issue, g...as a string of symbols. For ease of exposi - tion, we assume that each pair of parenthesis and set braces has length 2, and each comma has length 1

Recycling carbon dioxide during xylose fermentation by engineered Saccharomyces cerevisiae

USDA-ARS?s Scientific Manuscript database

In this study, we introduced the ribulose-1,5-bisphosphate carboxylase/oxygenase (RuBisCO) and phosphoribulokinase (PRK) into an engineered S. cerevisiae (SR8) harboring the XR/XDH pathway and up-regulated PPP 10, to enable CO2 recycling through a synthetic rPPP during xylose fermentation (Fig. 1). ...

Tactical Planning Workstation Software Description

DTIC Science & Technology

1990-09-01

menus an application wishes to use. It is only concerned with the location of the physically displayed objects within a form. The valid form fields...WAR COLLGE Numeric 4 N 16 ASG_FULDA Logical 1 N 17 XR_FULDA Logical 1 N 18 CMP COURSE Logical 1 N 19 MINIFREQ Character 1 N 20 WORKFREQ Character 1 N

Simulated Driving Changes in Young Adults with ADHD Receiving Mixed Amphetamine Salts Extended Release and Atomoxetine

ERIC Educational Resources Information Center

Kay, Gary G.; Michaels, M. Alex; Pakull, Barton

2009-01-01

Background: Psychostimulant treatment may improve simulated driving performance in young adults with attention-deficit/hyperactivity disorder (ADHD). Method: This was a randomized, double-blind, placebo-controlled, crossover study of simulated driving performance with mixed amphetamine salts--extended release (MAS XR) 50 mg/day (Cohort 1) and…

Using a Combination of UML, C2RM, XML, and Metadata Registries to Support Long-Term Development/Engineering

DTIC Science & Technology

2003-01-01

Authenticat’n (XCBF) Authorizat’n (XACML) (SAML) Privacy (P3P) Digital Rights Management (XrML) Content Mngmnt (DASL) (WebDAV) Content Syndicat’n...Registry/ Repository BPSS eCommerce XML/EDI Universal Business Language (UBL) Internet & Computing Human Resources (HR-XML) Semantic KEY XML SPECIFICATIONS

75 FR 18164 - Procurement List: Proposed Additions and Deletions

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-09

... . SUPPLEMENTARY INFORMATION: This notice is published pursuant to 41 U.S.C. 47(a)(2) and 41 CFR 51-2.3. Its.../Location: Janitorial Services, Corp of Engineers Buildings, Elmendorf AFB, AK, Corp of Engineers Buildings, Fort Richardson, AK. NPA: MQC Enterprises, Inc., Anchorage, AK. Contracting Activity: XR W2SN ENDIST...

Stress-dislocation interaction mechanism in low-temperature thermo-compression sintering of Ag NPs

NASA Astrophysics Data System (ADS)

Wang, Fuliang; Tang, Zikai; He, Hu

2018-04-01

The sintering of metal nanoparticles (NPs) has been widely studied in the field of nanotechnology, and low-temperature sintering has become the industry standard. In this study, a molecular dynamics (MD) model was established to study the sintering behaviour of silver NPs during low-temperature thermo-compression. Primarily, we studied the sintering process, in which the ratio of neck radius to particle radius (x/r) changes. Under a uniaxial pressure, the maximum ratio in the temperature range 420-425 K was 1. According to the change of x/r, the process can be broken down into three stages: the neck-formation stage, neck-growth stage, and neck-stability stage. In addition, the relationship between potential energy, internal stress, and dislocation density during sintering is discussed. The results showed that cycling internal stress played an important role in sintering. Under the uniaxial pressure, the stress-dislocation interaction was found to be the major mechanism for thermo-compression sintering because the plastic deformation product dislocation intensified the diffusion of atoms. Also, the displacement vector, the mean square displacement, and the changing crystal structure during sintering were studied.

Standing your Ground to Exoribonucleases: Function of Flavivirus Long Non-coding RNAs

PubMed Central

Charley, Phillida A.; Wilusz, Jeffrey

2015-01-01

Members of the Flaviviridae (e.g. Dengue virus, West Nile virus, and Hepatitis C virus) contain a positive-sense RNA genome that encodes a large polyprotein. It is now also clear most if not all of these viruses also produce an abundant subgenomic long non-coding RNA. These non-coding RNAs, which are called subgenomicflavivirus RNAs (sfRNAs) or Xrn1-resistant RNAs (xrRNAs), are stable decay intermediates generated from the viral genomic RNA through the stalling of the cellular exoribonuclease Xrn1 at highly structured regions. Several functions of these flavivirus long non-coding RNAs have been revealed in recent years. The generation of these sfRNAs/xrRNAs from viral transcripts results in the repression of Xrn1 and the dysregulation of cellular mRNA stability. The abundant sfRNAs also serve directly as a decoy for important cellular protein regulators of the interferon and RNA interference antiviral pathways. Thus the generation of long non-coding RNAs from flaviviruses, hepaciviruses and pestiviruses likely disrupts aspects of innate immunity and may directly contribute to viral replication, cytopathology and pathogenesis. PMID:26368052

Mfd translocase is necessary and sufficient for transcription-coupled repair in Escherichia coli.

PubMed

Adebali, Ogun; Sancar, Aziz; Selby, Christopher P

2017-11-10

Nucleotide excision repair in Escherichia coli is stimulated by transcription, specifically in the transcribed strand. Previously, it was shown that this transcription-coupled repair (TCR) is mediated by the Mfd translocase. Recently, it was proposed that in fact the majority of TCR in E. coli is catalyzed by a second pathway ("backtracking-mediated TCR") that is dependent on the UvrD helicase and the guanosine pentaphosphate (ppGpp) alarmone/stringent response regulator. Recently, we reported that as measured by the excision repair-sequencing (XR-seq), UvrD plays no role in TCR genome-wide. Here, we tested the role of ppGpp and UvrD in TCR genome-wide and in the lacZ operon using the XR-seq method, which directly measures repair. We found that the mfd mutation abolishes TCR genome-wide and in the lacZ operon. In contrast, the relA - spoT - mutant deficient in ppGpp synthesis carries out normal TCR. We conclude that UvrD and ppGpp play no role in TCR in E. coli . © 2017 by The American Society for Biochemistry and Molecular Biology, Inc.

Breeding of a xylose-fermenting hybrid strain by mating genetically engineered haploid strains derived from industrial Saccharomyces cerevisiae.

PubMed

Inoue, Hiroyuki; Hashimoto, Seitaro; Matsushika, Akinori; Watanabe, Seiya; Sawayama, Shigeki

2014-12-01

The industrial Saccharomyces cerevisiae IR-2 is a promising host strain to genetically engineer xylose-utilizing yeasts for ethanol fermentation from lignocellulosic hydrolysates. Two IR-2-based haploid strains were selected based upon the rate of xylulose fermentation, and hybrids were obtained by mating recombinant haploid strains harboring heterogeneous xylose dehydrogenase (XDH) (wild-type NAD(+)-dependent XDH or engineered NADP(+)-dependent XDH, ARSdR), xylose reductase (XR) and xylulose kinase (XK) genes. ARSdR in the hybrids selected for growth rates on yeast extract-peptone-dextrose (YPD) agar and YP-xylose agar plates typically had a higher activity than NAD(+)-dependent XDH. Furthermore, the xylose-fermenting performance of the hybrid strain SE12 with the same level of heterogeneous XDH activity was similar to that of a recombinant strain of IR-2 harboring a single set of genes, XR/ARSdR/XK. These results suggest not only that the recombinant haploid strains retain the appropriate genetic background of IR-2 for ethanol production from xylose but also that ARSdR is preferable for xylose fermentation.

Structure of Irreversibly Adsorbed Star Polymers

NASA Astrophysics Data System (ADS)

Akgun, Bulent; Aykan, Meryem Seyma; Canavar, Seda; Satija, Sushil K.; Uhrig, David; Hong, Kunlun

Formation of irreversibly adsorbed polymer chains on solid substrates have a huge impact on the wetting, glass transition, aging and polymer chain mobility in thin films. In recent years there has been many reports on the formation, kinetics and dynamics of these layers formed by linear homopolymers. Recent studies showed that by varying the number of polymer arms and arm molecular weight one can tune the glass transition temperature of thin polymer films. Using polymer architecture as a tool, the behavior of thin films can be tuned between the behavior of linear chains and soft colloids. We have studied the effect of polymer chain architecture on the structure of dead layer using X-ray reflectivity (XR) and atomic force microscopy. Layer thicknesses and densities of flattened and loosely adsorbed chains has been measured for linear, 4-arm, and 8-arm star polymers with identical total molecular weight as a function of substrate surface energy, annealing temperature and annealing time. Star polymers have been synthesized using anionic polymerization. XR measurements showed that 8-arm star PS molecules form the densest and the thickest dead layers among these three molecules.

Low Temperature Surface Carburization of Stainless Steels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collins, Sunniva R; Heuer, Arthur H; Sikka, Vinod K

2007-12-07

Low-temperature colossal supersaturation (LTCSS) is a novel surface hardening method for carburization of austenitic stainless steels (SS) without the precipitation of carbides. The formation of carbides is kinetically suppressed, enabling extremely high or colossal carbon supersaturation. As a result, surface carbon concentrations in excess of 12 at. % are routinely achieved. This treatment increases the surface hardness by a factor of four to five, improving resistance to wear, corrosion, and fatigue, with significant retained ductility. LTCSS is a diffusional surface hardening process that provides a uniform and conformal hardened gradient surface with no risk of delamination or peeling. The treatmentmore » retains the austenitic phase and is completely non-magnetic. In addition, because parts are treated at low temperature, they do not distort or change dimensions. During this treatment, carbon diffusion proceeds into the metal at temperatures that constrain substitutional diffusion or mobility between the metal alloy elements. Though immobilized and unable to assemble to form carbides, chromium and similar alloying elements nonetheless draw enormous amounts of carbon into their interstitial spaces. The carbon in the interstitial spaces of the alloy crystals makes the surface harder than ever achieved before by more conventional heat treating or diffusion process. The carbon solid solution manifests a Vickers hardness often exceeding 1000 HV (equivalent to 70 HRC). This project objective was to extend the LTCSS treatment to other austenitic alloys, and to quantify improvements in fatigue, corrosion, and wear resistance. Highlights from the research include the following: • Extension of the applicability of the LTCSS process to a broad range of austenitic and duplex grades of steels • Demonstration of LTCSS ability for a variety of different component shapes and sizes • Detailed microstructural characterization of LTCSS-treated samples of 316L and other alloys • Thermodynamic modeling to explain the high degree of carbon solubility possible in austenitic grades under the LTCSS process and experimental validation of model results • Corrosion testing to determine the corrosion resistance improvement possible from the LTCSS process • Erosion testing to determine the erosion resistance improvement possible from the LTCSS process • Wear testing to quantify the wear resistance improvement possible from the LTCSS process • Fatigue testing for quantifying the extent of improvement from the LTCSS process • Component treating and testing under simulated and in-line commercial operations XRD verified expanded austenite lattice, with no evidence of carbide precipitation. Carbon concentration profiles via Auger and electron dispersion spectroscopy (EDS) showed carbon levels in excess of 12 at. % in treated, type 316 SS. Scanning electron microscopy (SEM) of pulled-to-failure treated tensile specimens showed slip bands and no de-cohesion of the treated layer, verifying that the layer remains ductile. Compressive stresses in excess of 2 GPa (300 ksi) have been calculated at the surface of the case. Phase diagram (CALPHAD) (ThermoCalc) and Wagner dilute solution thermodynamic models were developed that calculate the solubility of carbon in austenite as a function of alloying content for the process time and temperature. Several commercial alloys have been modeled, and the model has been used to design experimental alloys with enhanced affinity for carbon solubility at treatment temperatures. Four experimental alloys were melted, rolled, and manufactured into test specimens, and the LTCSS treatment indicated successfully enhanced results and validated the predictions based on thermodynamic modeling. Electrochemical polarization curves show a 600 to 800 mV increase in pitting potential in treated (900-1000 mV) versus non-treated (200-300 mV) type 316 in chloride solutions. Treated 316L showed crevice-corrosion behavior similar to that of Ti-6Al-4V and Hastelloy C22. Cavitation tests showed significant increases in cavitation resistance for treated materials as compared to the non-treated materials. Standard ASTM pin-on-disk sliding friction and reciprocating friction wear tests also indicate significant enhancement in wear properties. Fatigue testing showed an order of magnitude improvement for treated versus non-treated Type 316 at the same maximum stress level (R = -1). The maximum stress at 107 cycles and the endurance stress for infinite life, improved by approximately 50%, from 30 to 45 ksi. The energy savings from this project is estimated at 21.8 trillion Btu/year by 2020. This energy savings will be associated with a CO2 reduction of 1.3 million ton/year. One application of this technology in a sludge pump of a cardboard recycling plant during the course of this project has resulted in an energy savings of 84. 106 Btu and cost savings of $900.« less

Assessing and improving organizational readiness to implement substance use disorder treatment in primary care: findings from the SUMMIT study.

PubMed

Ober, Allison J; Watkins, Katherine E; Hunter, Sarah B; Ewing, Brett; Lamp, Karen; Lind, Mimi; Becker, Kirsten; Heinzerling, Keith; Osilla, Karen C; Diamant, Allison L; Setodji, Claude M

2017-12-21

Millions of people with substance use disorders (SUDs) need, but do not receive, treatment. Delivering SUD treatment in primary care settings could increase access to treatment because most people visit their primary care doctors at least once a year, but evidence-based SUD treatments are underutilized in primary care settings. We used an organizational readiness intervention comprised of a cluster of implementation strategies to prepare a federally qualified health center to deliver SUD screening and evidence-based treatments (extended-release injectable naltrexone (XR-NTX) for alcohol use disorders, buprenorphine/naloxone (BUP/NX) for opioid use disorders and a brief motivational interviewing/cognitive behavioral -based psychotherapy for both disorders). This article reports the effects of the intervention on key implementation outcomes. To assess changes in organizational readiness we conducted pre- and post-intervention surveys with prescribing medical providers, behavioral health providers and general clinic staff (N = 69). We report on changes in implementation outcomes: acceptability, perceptions of appropriateness and feasibility, and intention to adopt the evidence-based treatments. We used Wilcoxon signed rank tests to analyze pre- to post-intervention changes. After 18 months, prescribing medical providers agreed more that XR-NTX was easier to use for patients with alcohol use disorders than before the intervention, but their opinions about the effectiveness and ease of use of BUP/NX for patients with opioid use disorders did not improve. Prescribing medical providers also felt more strongly after the intervention that XR-NTX for alcohol use disorders was compatible with current practices. Opinions of general clinic staff about the appropriateness of SUD treatment in primary care improved significantly. Consistent with implementation theory, we found that an organizational readiness implementation intervention enhanced perceptions in some domains of practice acceptability and appropriateness. Further research will assess whether these factors, which focus on individual staff readiness, change over time and ultimately predict adoption of SUD treatments in primary care.

Extended-Release Metformin Does Not Reduce the Clomiphene Citrate Dose Required to Induce Ovulation in Polycystic Ovary Syndrome

PubMed Central

Cataldo, Nicholas A.; Barnhart, Huiman X.; Legro, Richard S.; Myers, Evan R.; Schlaff, William D.; Carr, Bruce R.; Diamond, Michael P.; Carson, Sandra A.; Steinkampf, Michael P.; Coutifaris, Christos; McGovern, Peter G.; Gosman, Gabriella; Nestler, John E.; Giudice, Linda C.

2008-01-01

Context: When used for ovulation induction, higher doses of clomiphene may lead to antiestrogenic side effects that reduce fecundity. It has been suggested that metformin in combination with clomiphene can restore ovulation to some clomiphene-resistant anovulators with polycystic ovary syndrome (PCOS). Objective: Our objective was to determine if cotreatment with extended-release metformin (metformin XR) can lower the threshold dose of clomiphene needed to induce ovulation in women with PCOS. Design: A secondary analysis of data from the National Institute of Child Health and Human Development Cooperative Multicenter Reproductive Medicine Network prospective, double-blind, placebo-controlled multicenter clinical trial, Pregnancy in Polycystic Ovary Syndrome, was performed. Setting: Study volunteers at multiple academic medical centers were included. Participants: Women with PCOS and elevated serum testosterone who were randomized to clomiphene alone or with metformin (n = 209 in each group) were included in the study. Interventions: Clomiphene citrate, 50 mg daily for 5 d, was increased to 100 and 150 mg in subsequent cycles if ovulation was not achieved; half also received metformin XR, 1000 mg twice daily. Treatment was for up to 30 wk or six cycles, or until first pregnancy. Main Outcome Measures: Ovulation was confirmed by a serum progesterone more than or equal to 5 ng/ml, drawn prospectively every 1–2 wk. Results: The overall prevalence of at least one ovulation after clomiphene was 75 and 83% (P = 0.04) for the clomiphene-only and clomiphene plus metformin groups, respectively. Using available data from 314 ovulators, the frequency distribution of the lowest clomiphene dose (50, 100, or 150 mg daily) resulting in ovulation was indistinguishable between the two treatment groups. Conclusion: Metformin XR does not reduce the lowest dose of clomiphene that induces ovulation in women with PCOS. PMID:18505764

Effect of MMX® mesalamine coadministration on the pharmacokinetics of amoxicillin, ciprofloxacin XR, metronidazole, and sulfamethoxazole: results from four randomized clinical trials

PubMed Central

Pierce, David; Corcoran, Mary; Martin, Patrick; Barrett, Karen; Inglis, Susi; Preston, Peter; Thompson, Thomas N; Willsie, Sandra K

2014-01-01

Background MMX® mesalamine is a once daily oral 5-aminosalicylic acid formulation, effective in induction and maintenance of ulcerative colitis remission. Patients on long-term mesalamine maintenance may occasionally require concomitant antibiotic treatment for unrelated infections. Aim To evaluate the potential for pharmacokinetic interactions between MMX mesalamine and amoxicillin, ciprofloxacin extended release (XR), metronidazole, or sulfamethoxazole in four open-label, randomized, placebo-controlled, two-period crossover studies. Methods In all four studies, healthy adults received placebo once daily or MMX mesalamine 4.8 g once daily on days 1–4 in one of two treatment sequences. In studies 1 and 2, subjects also received a single dose of amoxicillin 500 mg (N=62) or ciprofloxacin XR 500 mg (N=30) on day 4. In studies 3 and 4, subjects received metronidazole 750 mg twice daily on days 1–3 and once on day 4 (N=30); or sulfamethoxazole 800 mg/trimethoprim 160 mg twice daily on days 1–3 and once on day 4 (N=44). Results MMX mesalamine had no significant effects on systemic exposure to amoxicillin, ciprofloxacin, or metronidazole; the 90% confidence intervals (CIs) around the geometric mean ratios (antibiotic + MMX mesalamine: antibiotic + placebo) for maximum plasma concentration (Cmax) and area under the plasma concentration–time curve (AUC) fell within the predefined equivalence range (0.80–1.25). Sulfamethoxazole exposure increased by a statistically significant amount when coadministered with MMX mesalamine; however, increased exposure (by 12% in Cmax at steady state; by 15% in AUC at steady state) was not considered clinically significant, as the 90% CIs for each point estimate fell entirely within the predefined equivalence range. Adverse events in all studies were generally mild. Conclusion MMX mesalamine may be coadministered with amoxicillin, ciprofloxacin, metronidazole, or sulfamethoxazole, without affecting pharmacokinetics or safety of these antibiotics. ClinicalTrials.gov identifiers NCT01442688, NCT01402947, NCT01418365, and NCT01469637. PMID:24868146

Effect of food on early drug exposure from extended-release stimulants: results from the Concerta, Adderall XR Food Evaluation (CAFE) Study.

PubMed

Auiler, J F; Liu, K; Lynch, J M; Gelotte, C K

2002-01-01

Stimulant therapy is the mainstay of treatment for children, adolescents and adults with attention-deficit/hyperactivity disorder (ADHD). Once-daily, extended-release oral formulations offer long acting control of symptoms by modifying drug delivery and absorption. In particular, consistency in early drug exposure is important for symptom control during school or work hours. Because these once-daily formulations are usually taken in the morning, the timing of the doses with breakfast is important. This study compared the effect of a high-fat breakfast on early drug exposure from a morning dose of two extended-release stimulant formulations: the osmotic-controlled OROS tablet of methylphenidate HCI (CONCERTA) and the capsule containing extended-release beads of mixed amphetamine salts (ADDERALL XR). The study had a single-dose, open-label, randomised, four-treatment, crossover design in which healthy subjects received either 36 mg CONCERTA or 20 mg ADDERALL XR in the morning after an overnight fast or a high-fat breakfast. Serial blood samples were collected over 28h to determine plasma concentrations of methylphenidate and amphetamine. The food effect on early drug exposure and the pharmacokinetic profiles up to 8 h after dosing of the two extended-release stimulants were directly compared using partial area (AUC(p4h), AUC(p6h) and AUC(p8h)) fed/fasted ratios. Amphetamine concentrations were markedly lower when the subjects had eaten breakfast, resulting in lower early drug exposures (p < 0.0001). By contrast, methylphenidate concentrations over the same 8 h were unaffected by breakfast, providing consistent levels of early drug exposure. Therefore, as a child's or adult's eating pattern varies, methylphenidate exposure over the first 8 h would be expected to have less day-to-day variation compared with amphetamine exposure. The osmotic-controlled OROS tablet provides a reliable and consistent delivery of methylphenidate HCI, independent of food, for patients with ADHD.

A prospective controlled study of diagnostic imaging for acute shin splints.

PubMed

Batt, M E; Ugalde, V; Anderson, M W; Shelton, D K

1998-11-01

The purpose of this prospective, observational study was to examine the relationship of clinical examination, plain radiograph (XR), triple-phase bone scan (TPBS), and magnetic resonance imaging (MRI) in the investigation of patients presenting with acute shin splints. 23 subjects with exercise induced lower leg pain and diffuse tibial tenderness of less than 3 months' duration were recruited. Subjects were excluded if there was clinical evidence of compartment syndrome, muscle hernia, or stress fracture. Each subject underwent XR, TPBS, and MRI within 2 wk of physical examination. Four asymptomatic controls underwent TPBS and MRI. Clinical findings, XR, TPBS, and MRI findings were independently recorded using a consistent template and subsequently analyzed. A single consensus lesion was chosen that provided the greatest overlap and highest grade to allow comparison of clinical and imaging findings. Sensitivity and specificity were calculated from data relating to clinical findings and diagnostic imaging. Eighteen subjects had bilateral symptoms and five unilateral with a mean duration of symptom of 5.4 wk (+/- 3.5). Of 41 symptomatic lower legs, there were TPBS abnormalities in 36 and MRI findings in 34. Analysis of clinical findings to TPBS and MRI demonstrated a sensitivity and specificity of 84%, 33% and 79%, 33%, respectively. Assuming TPBS as the "gold-standard," MRI findings demonstrated a sensitivity of 95% and specificity of 67%. There was poor agreement between the grading of TPBS and MRI (k = 0.3). In the 5/46 asymptomatic limbs, 3/5 demonstrated uptake on bone scan and 4/5 signal change with MRI. Imaging abnormalities were similarly seen in the four control patients. MRI may be used rather than TPBS and radiographs for evaluating acute tibial pain in athletes where avoidance of radiation exposure is desirable. Similar sensitivity and specificity may be expected from both investigations; however, in the light of abnormal TPBS and MRI findings in control and asymptomatic limbs, we recommend further studies be performed to define the extent of nonpathological TPBS and MRI changes.

A double-blind, randomized, placebo-controlled, active reference study of Lu AA21004 in patients with major depressive disorder

PubMed Central

Alvarez, Enric; Perez, Victor; Dragheim, Marianne; Loft, Henrik; Artigas, Francesc

2012-01-01

The efficacy, safety, and tolerability of Lu AA21004 vs. placebo using venlafaxine XR as active reference in patients with DSM-IV-TR major depressive disorder (MDD) were evaluated. Lu AA21004 is a novel antidepressant that is a 5-HT3 and 5-HT7 receptor antagonist, 5-HT1A receptor agonist, 5-HT1B receptor partial agonist and inhibitor of the 5-HT transporter in recombinant cell lines. In this 6-wk, multi-site study, 429 patients were randomly assigned (1:1:1:1) to 5 or 10 mg Lu AA21004, placebo or 225 mg venlafaxine XR. All patients had a baseline Montgomery–Åsberg Depression Rating Scale (MADRS) total score ⩾30. The primary efficacy analysis was based on the MADRS total score adjusting for multiplicity using a hierarchical testing procedure starting with the highest dose vs. placebo. Lu AA21004 was statistically significantly superior to placebo (n=105) in mean change from baseline in MADRS total score at week 6 (p<0.0001, last observation carried forward), with a mean treatment difference vs. placebo of 5.9 (5 mg, n=108), and 5.7 (10 mg, n=100) points. Venlafaxine XR (n=112) was also significantly superior to placebo at week 6 (p<0.0001). In total, 30 patients withdrew due to adverse events (AEs) – placebo: four (4%); 5 mg Lu AA21004: three (3%); 10 mg Lu AA21004: seven (7%); and venlafaxine: 16 (14%). The most common AEs were nausea, headache, hyperhidrosis, and dry mouth. No clinically relevant changes over time were seen in the clinical laboratory results, vital signs, weight, or ECG parameters. In this study, treatment with 5 mg and 10 mg Lu AA21004 for 6 wk was efficacious and well tolerated in patients with MDD. PMID:21767441

Effect of MMX® mesalamine coadministration on the pharmacokinetics of amoxicillin, ciprofloxacin XR, metronidazole, and sulfamethoxazole: results from four randomized clinical trials.

PubMed

Pierce, David; Corcoran, Mary; Martin, Patrick; Barrett, Karen; Inglis, Susi; Preston, Peter; Thompson, Thomas N; Willsie, Sandra K

2014-01-01

MMX(®) mesalamine is a once daily oral 5-aminosalicylic acid formulation, effective in induction and maintenance of ulcerative colitis remission. Patients on long-term mesalamine maintenance may occasionally require concomitant antibiotic treatment for unrelated infections. To evaluate the potential for pharmacokinetic interactions between MMX mesalamine and amoxicillin, ciprofloxacin extended release (XR), metronidazole, or sulfamethoxazole in four open-label, randomized, placebo-controlled, two-period crossover studies. In all four studies, healthy adults received placebo once daily or MMX mesalamine 4.8 g once daily on days 1-4 in one of two treatment sequences. In studies 1 and 2, subjects also received a single dose of amoxicillin 500 mg (N=62) or ciprofloxacin XR 500 mg (N=30) on day 4. In studies 3 and 4, subjects received metronidazole 750 mg twice daily on days 1-3 and once on day 4 (N=30); or sulfamethoxazole 800 mg/trimethoprim 160 mg twice daily on days 1-3 and once on day 4 (N=44). MMX mesalamine had no significant effects on systemic exposure to amoxicillin, ciprofloxacin, or metronidazole; the 90% confidence intervals (CIs) around the geometric mean ratios (antibiotic + MMX mesalamine: antibiotic + placebo) for maximum plasma concentration (Cmax) and area under the plasma concentration-time curve (AUC) fell within the predefined equivalence range (0.80-1.25). Sulfamethoxazole exposure increased by a statistically significant amount when coadministered with MMX mesalamine; however, increased exposure (by 12% in Cmax at steady state; by 15% in AUC at steady state) was not considered clinically significant, as the 90% CIs for each point estimate fell entirely within the predefined equivalence range. Adverse events in all studies were generally mild. MMX mesalamine may be coadministered with amoxicillin, ciprofloxacin, metronidazole, or sulfamethoxazole, without affecting pharmacokinetics or safety of these antibiotics. NCT01442688, NCT01402947, NCT01418365, and NCT01469637.

The Functions of BRCA2 in Homologous Recombinational Repair

DTIC Science & Technology

2005-07-01

human Rad5l, Rad51B and Rad51C proteins 5 homogeneity using spermidine precipitation and sequential column chromatography with hydroxyapatite , Q-Sepharose...G. G., Albala, J. S., Shen, Z., ovary mutants for XRCC4, Ku86, and DNA-PKcs (the XR -1 and Schild, D. (1998) Nucleic Acids Res. 26, 1179-1184 oh 11

Accuracy of Tracking Forest Machines with GPS

Treesearch

M.W. Veal; S.E. Taylor; T.P. McDonald; D.K. McLemore; M.R. Dunn

2001-01-01

This paper describes the results of a study that measured the accuracy of using GPS to track movement offorest machines. Two different commercially available GPS receivers (Trimble ProXR and GeoExplorer II) were used to track wheeled skidders under three different canopy conditions at two different vehicle speeds. Dynamic GPS data were compared to position data...

Clonidine Extended-Release Tablets for Pediatric Patients with Attention-Deficit/Hyperactivity Disorder

ERIC Educational Resources Information Center

Jain, Rakesh; Segal, Scott; Kollins, Scott H.; Khayrallah, Moise

2011-01-01

Objective: This study examined the efficacy and safety of clonidine hydrochloride extended-release tablets (CLON-XR) in children and adolescents with attention-deficit/hyperactivity disorder (ADHD). Method: This 8-week, placebo-controlled, fixed-dose trial, including 3 weeks of dose escalation, of patients 6 to 17 years old with ADHD evaluated the…

EFFECTS OF THE INSECT JUVENILE HORMONE AGONIST, METHOPRENE ON FEMALE GROWTH AND REPRODUCTION IN THE GULF SAND FIDDLER CRAB, UCA PANACEA

EPA Science Inventory

Adult Uca panacea were distributed randomly (250 females, 100 males per pond) into six estuarine ponds to determine the effects of field applications of methoprene (AltosidO XR briquets) on female growth and reproduction. Duplicate reference ponds, low-dose ponds, and high-dose p...

Experimental investigation of cyclic thermomechanical deformation in torsion

NASA Technical Reports Server (NTRS)

Ellis, John R.; Castelli, Michael G.; Bakis, Charles E.

1992-01-01

An investigation of thermomechanical testing and deformation behavior of tubular specimens under torsional loading is described. Experimental issues concerning test accuracy and control specific to thermomechanical loadings under a torsional regime are discussed. A series of shear strain-controlled tests involving the nickel-base superalloy Hastelloy X were performed with various temperature excursions and compared to similar thermomechanical uniaxial tests. The concept and use of second invariants of the deviatoric stress and strain tensors as a means of comparing uniaxial and torsional specimens is also briefly presented and discussed in light of previous thermomechanical tests conducted under uniaxial conditions.

A data acquisition and control program for axial-torsional fatigue testing

NASA Technical Reports Server (NTRS)

Kalluri, Sreeramesh; Bonacuse, Peter J.

1989-01-01

A computer program was developed for data acquisition and control of axial-torsional fatigue experiments. The multitasked, interrupt-driven program was written in Pascal and Assembly. This program is capable of dual-channel control and six-channel data acquisition. It can be utilized to perform inphase and out-of-phase axial-torsional isothermal fatigue or deformation experiments. The program was successfully used to conduct inphase axial-torsional fatigue experiments on 304 stainless steel at room temperature and on Hastelloy X at 800 C. The details of the software and some of the results generated to date are presented.

The Functions of BRCA2 in Homologous Recombinational Repair

DTIC Science & Technology

2004-07-01

chromatography with hydroxyapatite , Q-Sepharose, heparin affinity and MonoQ column (Fig. 4.). We have been able to obtain about 10 mg of the purified Rad51...and DNA- PKcs (the XR -1, xrs5/6, and V3 cell lines, respectively) are highly sensitive to IR in G1 and early S phases, compared to the wild-type, but

Methodological Issues in the Assessment of Medication Effects in Children Diagnosed with Attention Deficit Hyperactivity Disorder (ADHD)

ERIC Educational Resources Information Center

Kollins, Scott H.

2004-01-01

Attention deficit hyperactivity disorder (ADHD) is one of the most commonly diagnosed disorders in school-aged children and is usually treated with stimulant medications, including methylphenidate (MPH; Ritalin[R], Ritalin-LA[R], Concerta[R], Metadate[R], or Focalin[R]) and other drug compounds (e.g., Adderall[R], Adderall-XR[R], or Dexedrine).…

In-situ conversion of rGO/Ni2P composite from GO/Ni-MOF precursor with enhanced electrochemical property

NASA Astrophysics Data System (ADS)

Lv, Zijian; Zhong, Qin; Bu, Yunfei

2018-05-01

Owing to the metalloid characteristic and superior electrical conductivity, the metal phosphides have received increasing interests in energy storage systems. Here, xrGO/Ni2P composites are successfully synthesized via an In-situ phosphorization process with GO/Ni-MOF as precursors. Compared to pure Ni2P, the xrGO/Ni2P composites appear enhanced electrochemical properties in terms of the specific capacitance and cycling performance as electrodes for supercapacitors. Especially, the 2rGO/Ni2P electrode shows a highest specific capacitance of 890 F g-1 at 1 A g-1 among the obtained composites. The enhancement can be attributed to the inherited structure from Ni-MOF and the well assembled of rGO and Ni2P through the In-situ conversion process. Moreover, when applied as positive electrode in a hybrid supercapacitor, an energy density of 35.9 W h kg-1 at a power density of 752 W kg-1 has been achieved. This work provides an In-situ conversion strategy for the synthesis of rGO/Ni2P composite which might be a promising electrode material for SCs.

Combined Medication and CBT for Generalized Anxiety Disorder with African American Participants: Reliability and Validity of Assessments and Preliminary Outcomes

PubMed Central

Markell, Hannah M.; Newman, Michelle G.; Gallop, Robert; Gibbons, Mary Beth Connolly; Rickels, Karl; Crits-Christoph, Paul

2014-01-01

Using data from a study of combined cognitive behavioral therapy (CBT) and venlafaxine XR in the treatment of generalized anxiety disorder (GAD), the current article examines the reliability and convergent validity of scales, and preliminary outcomes, for African American compared to European American patients. Internal consistency and short-term stability coefficients for African Americans (n=42) were adequate and similar or higher compared to those found for European Americans (n=164) for standard scales used in GAD treatment research. Correlations among outcome measures among African Americans were in general not significantly different for African Americans compared to European Americans. A subset of patients with DSM-IV–diagnosed GAD (n = 24 African Americans; n = 52 European Americans) were randomly selected to be offered the option of adding 12 sessions of CBT to venlafaxine XR treatment. Of those offered CBT, 33.3% (n = 8) of the African Americans, and 32.6% (n = 17) of the European Americans accepted and attended at least one CBT treatment session. The outcomes for African Americans receiving combined treatment were not significantly different from European Americans receiving combined treatment on primary or secondary efficacy measures. PMID:24912462

Structure of Room Temperature Ionic Liquids on Charged Graphene: An integrated experimental and computational study

NASA Astrophysics Data System (ADS)

Uysal, Ahmet; Zhou, Hua; Lee, Sang Soo; Fenter, Paul; Feng, Guang; Li, Song; Cummings, Peter; Fulvio, Pasquale; Dai, Sheng; McDonough, Jake; Gogotsi, Yury

2014-03-01

Electrical double layer capacitors (EDLCs) with room temperature ionic liquid (RTIL) electrolytes and carbon electrodes are promising candidates for energy storage devices with high power density and long cycle life. We studied the potential and time dependent changes in the electric double layer (EDL) structure of an imidazolium-based room temperature ionic liquid (RTIL) electrolyte at an epitaxial graphene (EG) surface. We used in situ x-ray reflectivity (XR) to determine the EDL structure at static potentials, during cyclic voltammetry (CV) and potential step measurements. The static potential structures were also investigated with fully atomistic molecular dynamics (MD) simulations. Combined XR and MD results show that the EDL structure has alternating anion/cation layers within the first nanometer of the interface. The dynamical response of the EDL to potential steps has a slow component (>10 s) and the RTIL structure shows hysteresis during CV scans. We propose a conceptual model that connects nanoscale interfacial structure to the macroscopic measurements. This material is based upon work supported as part of the Fluid Interface Reactions, Structures and Transport (FIRST) Center, an Energy Frontier Research Center funded by the U.S. Department of Energy (DOE), Office of Science (SC), Office of Basic Energy

Nonmedical use of prescription ADHD stimulant medications among adults in a substance abuse treatment population: early findings from the NAVIPPRO surveillance system.

PubMed

Cassidy, Theresa A; McNaughton, Emily C; Varughese, Sajan; Russo, Leo; Zulueta, Mirella; Butler, Stephen F

2015-04-01

To examine nonmedical use (NMU) of prescription ADHD stimulants among adults evaluated for substance abuse treatment. 147,816 assessments from the National Addictions Vigilance Intervention and Prevention Program (NAVIPPRO) system (10/01/2009 through 03/31/2012) examined NMU prevalence, routes of administration (ROA), and diversion sources. Past 30-day NMU for prescription stimulants (1.29%) was significantly lower than that of prescription opioids (19.79%) or sedatives (10.62%). For stimulant products, NMU for Adderall was 0.62, followed by Adderall XR (0.42), Ritalin (0.16), Vyvanse (0.12), and Concerta (0.08); product differences likely have limited clinical relevance given the low estimates (<1%). Higher NMU per prescriptions was for Adderall (4.92), Ritalin (4.68), and Adderall XR (3.18) compared with newer formulations (Vyvanse 1.26, Concerta 0.89). Diversion source was mainly family/friends with no differences between products; swallowing whole was the most frequent ROA. Prescription stimulant NMU was low compared with other prescription medications among individuals assessed for substance abuse problems, with little difference among specific products. © 2013 SAGE Publications.

3D magnetic nanostructures grown by focused electron and ion beam induced deposition

NASA Astrophysics Data System (ADS)

Fernandez-Pacheco, Amalio

Three-dimensional nanomagnetism is an emerging research area, where magnetic nanostructures extend along the whole space, presenting novel functionalities not limited to the substrate plane. The development of this field could have a revolutionary impact in fields such as electronics, the Internet of Things or bio-applications. In this contribution, I will show our recent work on 3D magnetic nanostructures grown by focused electron and ion beam induced deposition. This 3D nano-printing techniques, based on the local chemical vapor deposition of a gas via the interaction with electrons and ions, makes the fabrication of complex 3D magnetic nanostructures possible. First, I will show how by exploiting different growth regimes, suspended Cobalt nanowires with modulated diameter can be patterned, with potential as domain wall devices. Afterwards, I will show recent results where the synthesis of Iron-Gallium alloys can be exploited in the field of artificial multiferroics. Moreover, we are developing novel methodologies combining physical vapor deposition and 3D nano-printing, creating Permalloy 3D nanostrips with controllable widths and lengths up to a few microns. This approach has been extended to more complex geometries by exploiting advanced simulation growth techniques combining Monte Carlo and continuum model methods. Throughout the talk, I will show the methodology we are following to characterize 3D magnetic nanostructures, by combining magneto-optical Kerr effect, scanning probe microscopy and electron and X-R magnetic imaging, and I will highlight some of the challenges and opportunities when studying these structures. I acknowledge funding from EPSRC and the Winton Foundation.

World Epidemiology Review, Number 111.

DTIC Science & Technology

1978-10-25

indicator is gWn, the infor- mation was summarized x?r extracted . / \\ l Unfamiliar names rendered phonetically or transliterated are enclosed in...subsidies to non-govern- mental agencies so that oralit can be distributed to remote areas just as aspirin, cajuput oil , medicinal herbs and other...ground nuts, soys beans and sunflower, and which also exist in the oils and meals manufactured from these products. The existence of the Aflotoxin

Influence of xylem ray integrity and degree of polymerization on bending strength of beech wood decayed by Pleurotus ostreatus and Trametes versicolor

Treesearch

Ehsan Bari; Reza Oladi; Olaf Schmidt; Carol A. Clausen; Katie Ohno; Darrel D. Nicholas; Mehrdad Ghodskhah Daryaei; Maryam Karim

2015-01-01

The scope of this research was to evaluate the influence of xylem ray (XR) and degree of polymerization (DP) of holocellulose in Oriental beech wood (Fagus orientalis Lipsky.) on impact bending strength against two white-rot fungi. Beech wood specimens, exposed to Pleurotus ostreatus and Trametes versicolor, were evaluated for...

A fixed-dose combination tablet of gemigliptin and metformin sustained release has comparable pharmacodynamic, pharmacokinetic, and tolerability profiles to separate tablets in healthy subjects.

PubMed

Park, Sang-In; Lee, Howard; Oh, Jaeseong; Lim, Kyoung Soo; Jang, In-Jin; Kim, Jeong-Ae; Jung, Jong Hyuk; Yu, Kyung-Sang

2015-01-01

In type 2 diabetes mellitus, fixed-dose combination (FDC) can provide the complementary benefits of correction of multiple pathophysiologic defects such as dysfunctions in glycemic or metabolic control while improving compliance compared with separate tablets taken together. The objective of the study reported here was to compare the pharmacodynamic (PD), pharmacokinetic (PK), and tolerability profiles of gemigliptin and extended-release metformin (metformin XR) between FDC and separate tablets. A randomized, open-label, single-dose, two-way, two-period, crossover study was conducted in 28 healthy male volunteers. Two FDC tablets of gemigliptin/metformin 25/500 mg or separate tablets of gemigliptin (50 mg ×1) and metformin XR (500 mg ×2) were orally administered in each period. Serial blood samples were collected up to 48 hours post-dose to determine dipeptidyl peptidase 4 (DPP-4) activity using spectrophotometric assay and concentrations of gemigliptin and metformin using tandem mass spectrometry. Geometric mean ratios (GMRs) of FDC to separate tablet formulations and their 90% confidence intervals (CIs) were calculated to compare the PD and PK parameters between the two formulations. Tolerability was assessed throughout the study. The plasma DPP-4 activity-time curves of the FDC and the separate tablets almost overlapped, leading to a GMR (90% CI) of the FDC to separate tablets for the plasma DPP-4 activity and its maximum inhibition of 1.00 (0.97-1.04) and 0.92 (0.82-1.05), respectively. Likewise, all of the GMRs (90% CIs) of FDC to separate tablets for the area under the plasma concentration-time curve and maximum plasma concentration of gemigliptin and metformin fell entirely within the conventional bioequivalence range of 0.80-1.25. Both the FDC and separate tablets were well tolerated. The PD, PK, and tolerability profiles of gemigliptin and metformin XR in FDC and separate tablets were found to be comparable. The FDC tablet of gemigliptin and metformin sustained release can be a convenient therapeutic option in patients with type 2 diabetes mellitus requiring a combination approach.

Mini-BRU/BIPS 1300 watt (sub)e dynamic power conversion system development: Executive summary

NASA Technical Reports Server (NTRS)

1978-01-01

The status of the Brayton Isotope Power System (BIPS) is summarized. A 1200 watt sub e ground development unit was built and tested in a 0.000010 torr vacuum environment. Peformance mapping and 1000 hours of proof of concept system testing were completed. Specific components, primarily turbocompressor/alternator and recuperator performed according to predictions, thus achieving the design goal of 25 percent net power conversion efficiency. The system was fabricated from superalloy (Hastelloy-X and Waspaloy) thus placing it entirely within current state-of-the-art technology. The system could be flyable in the early 1980's pending flight qualification.

ECLSS Universal Waste Management System (UWMS) Metal Materials Compatibility Study- Electrochemical and Crevice Corrosion Evaluation

NASA Technical Reports Server (NTRS)

Lee, R. E.

2017-01-01

Electrochemical and crevice corrosion laboratory test results are presented for three noble metal candidates with possible application on the Universal Waste Management System (UWMS) in support of the Environmental Control and Life Support System (ECLSS) aboard the International Space Station (ISS). The three metal candidates, which included Inconel 625, Hastelloy C276 and Titanium 6Al-4V, were evaluated in two solutions representative of the acidic pretreatment formulations utilized during processing of waste liquids within the ECLSS. Final test results and data analysis indicated that the passive layer on all three metals provides excellent corrosion protection in both solutions under standard test conditions.

Stress Corrosion Evaluation of Various Metallic Materials for the International Space Station Water Recycling System

NASA Technical Reports Server (NTRS)

Torres, P. D.

2015-01-01

A stress corrosion evaluation was performed on Inconel 625, Hastelloy C276, titanium commercially pure (TiCP), Ti-6Al-4V, Ti-6Al-4V extra low interstitial, and Cronidur 30 steel as a consequence of a change in formulation of the pretreatment for processing the urine in the International Space Station Environmental Control and Life Support System Urine Processing Assembly from a sulfuric acid-based to a phosphoric acid-based solution. The first five listed were found resistant to stress corrosion in the pretreatment and brine. However, some of the Cronidur 30 specimens experienced reduction in load-carrying ability.

Evaluation and Control of Mechanical Degradation of Austenitic Stainless 310S Steel Substrate During Coated Superconductor Processing

NASA Astrophysics Data System (ADS)

Kim, Seung-Gyu; Kim, Najung; Shim, Hyung-Seok; Kwon, Oh Min; Kwon, Dongil

2018-05-01

The superconductor industry considers cold-rolled austenitic stainless 310S steel a less expensive substitute for Hastelloy X as a substrate for coated superconductor. However, the mechanical properties of cold-rolled 310S substrate degrade significantly in the superconductor deposition process. To overcome this, we applied hot rolling at 900 °C (or 1000 °C) to the 310S substrate. To check the property changes, a simulated annealing condition equivalent to that used in manufacturing was determined and applied. The effects of the hot rolling on the substrate were evaluated by analyzing its physical properties and texture.

Determination of the relative resistance to ignition of selected turbopump materials in high-pressure, high-temperature, oxygen environments, volume 1

NASA Technical Reports Server (NTRS)

Stoltzfus, Joel M.; Benz, Frank J.

1986-01-01

Advances in the design of the liquid oxygen, liquid hydrogen engines for the Space Transportation System call for the use of warm, high-pressure oxygen as the driving gas in the liquid oxygen turbopump. The NASA Lewis Research Center requested the NASA White Sands Test Facility (WSTF) to design a test program to determine the relative resistance to ignition of nine selected turbopump materials: Hastelloy X, Inconel 600, Invar 36, Monel K-500, nickel 200, silicon carbide, stainless steel 316, and zirconium copper. The materials were subjected to particle impact and to frictional heating in high-pressure oxygen.

Design and Calibration of the ARL Mach 3 High Reynolds Number Facility

DTIC Science & Technology

1975-01-01

degrees Rankine. Test rhombus determinations included lateral and longitudinal Mach number distributions and flow angularity measurements. A...43 3. THE TUNNEL EMPTY MACH NUMBER DISTRIBUTION 45 4. THE CENTERLINE RMS MACH NUMBER 46 5. FLOW ANGULARITY MEASUREMENTS 46 6. BLOCKAGE TESTS... Angularity Wedge Scale Drawing of Flow Angularity Cone Normalized Surface Pressure Difference versus Angle of Attack at xp/xr = - 0.690 for po

Changing flux of xylose metabolites by altering expression of xylose reductase and xylitol dehydrogenase in recombinant Saccharomyces cerevisiae

Treesearch

Yong-Su Jin; Thomas W. Jeffries

2003-01-01

We changed the fluxes of xylose metabolites in recombinant Saccharomyces cerevisiae by manipulating expression of Pichia stipitis genes(XYL1 and XYL2) coding for xylose reductase (XR) and xylitol dehydrogenase (XDH), respectively. XYL1 copy number was kept constant by integrating it into the chromosome. Copy numbers of XYL2 were varied either by integrating XYL2 into...

Geometric Factors in Target Positioning and Tracking

DTIC Science & Technology

2009-07-01

Shalom and X.R. Li, Multitarget-Multisensor Tracking: Principles and Techniques, YBS Publishing, Storrs, CT, 1995. [2] S. Blackman and R. Popoli, Design...Multitarget-Multisensor Tracking: Applications and Advances, Vol.2, Y. Bar- Shalom (Ed.), 325-392, Artech House, Norwood, MA, 1999. [10] B. Ristic...R. Yarlagadda, I. Ali , N. Al-Dhahir, and J. Hershey, “GPS GDOP Metric,” IEE Proc. Radar, Sonar Navig, 147(5), Oct. 2000. [14] A. Kelly

Factors affecting distribution patterns of organic carbon in sediments at regional and national scales in China.

PubMed

Cao, Qingqing; Wang, Hui; Zhang, Yiran; Lal, Rattan; Wang, Renqing; Ge, Xiuli; Liu, Jian

2017-07-14

Wetlands are an important carbon reservoir pool in terrestrial ecosystems. Light fraction organic carbon (LFOC), heavy fraction organic carbon (HFOC), and dissolved organic carbon (DOC) were fractionated in sediment samples from the four wetlands (ZR: Zhaoniu River; ZRCW: Zhaoniu River Constructed Wetland; XR: Xinxue River; XRCW: Xinxue River Constructed Wetland). Organic carbon (OC) from rivers and coasts of China were retrieved and statistically analyzed. At regional scale, HFOC stably dominates the deposition of OC (95.4%), whereas DOC and LFOC in ZR is significantly higher than in ZRCW. Concentration of DOC is significantly higher in XRCW (30.37 mg/l) than that in XR (13.59 mg/l). DOC and HFOC notably distinguish between two sampling campaigns, and the deposition of carbon fractions are limited by low nitrogen input. At the national scale, OC attains the maximum of 2.29% at precipitation of 800 mm. OC has no significant difference among the three climate zones but significantly higher in river sediments than in coasts. Coastal OC increases from Bohai Sea (0.52%) to South Sea (0.70%) with a decrease in latitude. This study summarizes the factors affecting organic carbon storage in regional and national scale, and have constructive implications for carbon assessment, modelling, and management.

Xylose reductase and xylitol dehydrogenase activities of Candida guilliermondii as a function of different treatments of sugarcane bagasse hemicellulosic hydrolysate employing experimental design.

PubMed

Alves, Lourdes A; Vitolo, Michele; Felipe, Maria das Graças A; de Almeida e Silva, João Batista

2002-01-01

The sugarcane bagasse hydrolysate, which is rich in xylose, can be used as culture medium for Candida guilliermondii in xylitol production. However, the hydrolysate obtained from bagasse by acid hydrolysis at 120 degrees C for 20 min has by-products (acetic acid and furfural, among others), which are toxic to the yeast over certain concentrations. So, the hydrolysate must be pretreated before using in fermentation. The pretreatment variables considered were: adsorption time (15,37.5, and 60 min), type of acid used (H2So4 and H3Po4), hydrolysate concentration (original, twofold, and fourfold concentrated), and active charcoal (0.5, 1.75 and 3.0%). The suitability of the pretreatment was followed by measuring the xylose reductase (XR) and xylitol dehydrogenase (XD) activity of yeast grown in each treated hydrolysate. The response surface methodology (2(4) full factorial design with a centered face) indicated that the hydrolysate might be concentrated fourfold and the pH adjusted to 7.0 with CaO, followed by reduction to 5.5 with H3PO4. After that it was treated with active charcoal (3.0%) by 60 min. This pretreated hydrolysate attained the high XR/XD ratio of 4.5.

P-glycoprotein retains function when reconstituted into a sphingolipid- and cholesterol-rich environment.

PubMed

Modok, Szabolcs; Heyward, Catherine; Callaghan, Richard

2004-10-01

P-glycoprotein (P-gp) appears to be associated within specialized raftlike membrane microdomains. The activity of P-gp is sensitive to its lipid environment, and a functional association in raft microdomains will require that P-gp retains activity in the microenvironment. Purified hamster P-gp was reconstituted in liposomes comprising sphingomyelin and cholesterol, both highly enriched in membrane microdomains and known to impart a liquid-ordered phase to bilayers. The activity of P-gp was compared with that of proteoliposomes composed of crude egg phosphatidylcholine (unsaturated) or dipalmitoyl phosphatidylcholine (saturated) in the presence or absence of cholesterol. The maximal rate of ATP hydrolysis was not significantly altered by the nature of the lipid species. However, the potencies of nicardipine and XR9576 to modulate the ATPase activity of P-gp were increased in the sphingolipid-based proteoliposomes. The drug-P-gp interaction was investigated by measurement of the rates of [(3)H]XR9576 association and dissociation from the transporter. The lipid environment of P-gp did not affect these kinetic parameters of drug binding. In summary, P-gp retains function in liquid-ordered cholesterol and sphingolipid model membranes in which the communication between the transmembrane and the nucleotide binding domains after drug binding to the protein is more efficient.

Dimensionally Controlled Lithiation of Chromium Oxide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fister, Tim T.; Hu, Xianyi; Esbenshade, Jennifer

Oxide conversion reactions are an alternative approach for high capacity lithium ion batteries but are known to suffer from structural irreversibility associated with the phase separation and reconstitution of reduced metal species and Li2O. In particular, the morphology of the reduced metal species is thought to play a critical role in the electrochemical properties of a conversion material. Here we use a model electrode with alternating layers of chromium and chromium oxide to better understand and control these phase changes in real-time and at molecular length scales. Despite lacking crystallinity at the atomic scale, this superstructure is observed (with X-raymore » reflectivity, XR) to lithiate and delithiate in a purely one-dimensional manner, preserving the layered structure. The XR data show that the metal layers act as nucleation sites for the reduction of chromium in the conversion reaction. Irreversibility during delithiation is due to the formation of a ternary phase, LiCrO2, which can be further delithiated at higher potentials. The results reveal that the combination of confining lithiation to nanoscale sheets of Li2O and the availability of reaction sites in the metal layers in the layered structure is a strategy for improving the reversibility and mass transport properties that can be used in a wide range of conversion materials.« less

The Quantitative Measurements of Vascular Density and Flow Area of Optic Nerve Head Using Optical Coherence Tomography Angiography.

PubMed

Bazvand, Fatemeh; Mirshahi, Reza; Fadakar, Kaveh; Faghihi, Houshangh; Sabour, Siamak; Ghassemi, Fariba

2017-08-01

The purpose of this study was to evaluate the vascular density (VD) and the flow area on optic nerve head (ONH) and peripapillary area, and the impact of age and sex using optical coherence tomography angiography (OCTA) in healthy human subjects. Both eyes of each volunteer were scanned by an RTVue XR Avanti; Optovue with OCTA using the split-spectrum amplitude-decorrelation angiography algorithm technique. Masked graders evaluated enface angiodisc OCTA data. The flow area of ONH and the VD were automatically calculated. A total of 79 eyes of patients with a mean age of 37.03±11.27 were examined. The total ONH (papillary and peripapillary) area VD was 56.03%±4.55%. The flow area of the ONH was 1.74±0.10 mm/1.34 mm. The temporal and inferotemporal peripapillary VD was different between male and female patients. Increasing age causes some changes in the flow area of the ONH and the papillary VD from the third to the fourth decade (analysis of variance test; P<0.05). A normal quantitative database of the flow area and VD of the papillary and peripapillary area, obtained by RTVue XR with OCT angiography technique, is presented here.

Quantitative understanding of the role of grain boundaries in polycrystalline deformation via multiscale digital image correlation

NASA Astrophysics Data System (ADS)

Abuzaid, Wael Z. M.

In this study, high resolution ex situ digital image correlation (DIC) was used to measure plastic strain accumulation in polycrystalline Hastelloy X, a nickel-based superalloy, subjected to monotonic and cyclic loading conditions. In addition, the underlying microstructure was characterized with similar spatial resolution using electron backscatter diffraction (EBSD). The experimental results were utilized to investigate the localization of plastic strains in the vicinity of grain boundaries (GBs). Particularly we address the interaction of slip with GBs which can result in slip blockage or slip transmission and investigate how these two possible outcomes of slip-GB interaction influence the plastic strain magnitudes and fatigue crack formation in GB regions. In the first part of this work, we focus on slip transmission across GBs. Strain measurements with sub-grain level spatial resolution were acquired for Hastelloy X deformed plastically in uniaxial tension. The full field DIC measurements show a high level of heterogeneity in the plastic response with large variations in strain magnitudes within grains and across GBs. We used the experimental results to study these variations in strains, focusing specifically on the role of slip transmission across GBs in the development of strain heterogeneities. For every GB in the polycrystalline aggregate, we have established the most likely dislocation reaction and used that information to calculate the residual Burgers vector and plastic strain magnitudes due to slip transmission across each interface. From our analysis, we show an inverse relation between the magnitudes of the residual Burgers vector and the plastic strains across GBs. We therefore emphasize the importance of considering the magnitude of the residual Burgers vector to obtain a better description of the GB resistance to slip transmission, which in turn influences the local plastic strains in the vicinity of grain boundaries. In the second part of this work, we consider fatigue micro-crack formation. It is widely accepted that the localization in plastic strains is a necessary condition and a precursor for the nucleation of fatigue cracks. However a clear and quantitative assessment of the correlation between strain localization and fatigue micro-crack lengths requires further investigation. To address this point, high resolution deformation measurements using DIC were conducted on polycrystalline Hastelloy X subjected to fatigue loading. The sub-grain level strain measurements were made prior to the formation of micro-cracks. The correlation between the localization of plastic strains, very early on during the loading (e.g., less than 1,000 cycles), and the micro-cracks which were detected later in the life of the sample ( e.g., around 10,000 cycles) is discussed in this thesis. Particular focus is given to the difference in grain boundary response, either blocking or transmitting slip, and the associated fatigue micro-crack lengths generated in the vicinity of these boundaries. The results show a clear correlation between both the locations and lengths of fatigue micro-cracks and the localization of plastic strains very early in the loading process. In addition, we observed that for the same number of cycles, the transmission of slip across grain boundaries resulted in longer transgranular cracks compared to cracks near grains surrounded by blocking grain boundaries which were shorter cracks and confined within single grains. In the last part of this study, experiments were conducted on Hastelloy X subjected to fatigue loading. The purpose of the experiments was to investigate the scatter in fatigue lives under similar loading conditions. We also used a recent novel fatigue model based on persistent slip band (PSB) -- GB interaction to investigate the scatter in fatigue lives and shed light into the critical types of GBs which nucleate cracks. The implementation of this model provides simulation results of the scatter in fatigue life, which are consistent with the scatter observed from experiments. Finally, with the use of high resolution strain measurements, we provide a critical evaluation of some aspects of the modeling approach, for example the formation of grain clusters and their influence on fatigue life. Also the role of special GBs, mainly annealing twin boundaries (Sigma3 GBs), was evaluated.

Elevated Temperature Crack Propagation

NASA Technical Reports Server (NTRS)

Orange, Thomas W.

1994-01-01

This paper is a summary of two NASA contracts on high temperature fatigue crack propagation in metals. The first evaluated the ability of fairly simple nonlinear fracture parameters to correlate crack propagation. Hastelloy-X specimens were tested under isothermal and thermomechanical cycling at temperatures up to 980 degrees C (1800 degrees F). The most successful correlating parameter was the crack tip opening displacement derived from the J-integral. The second evaluated the ability of several path-independent integrals to correlate crack propagation behavior. Inconel 718 specimens were tested under isothermal, thermomechanical, temperature gradient, and creep conditions at temperatures up to 650 degrees C (1200 degrees F). The integrals formulated by Blackburn and by Kishimoto correlated the data reasonably well under all test conditions.

Research and development program for non-linear structural modeling with advanced time-temperature dependent constitutive relationships

NASA Technical Reports Server (NTRS)

Walker, K. P.

1981-01-01

Results of a 20-month research and development program for nonlinear structural modeling with advanced time-temperature constitutive relationships are reported. The program included: (1) the evaluation of a number of viscoplastic constitutive models in the published literature; (2) incorporation of three of the most appropriate constitutive models into the MARC nonlinear finite element program; (3) calibration of the three constitutive models against experimental data using Hastelloy-X material; and (4) application of the most appropriate constitutive model to a three dimensional finite element analysis of a cylindrical combustor liner louver test specimen to establish the capability of the viscoplastic model to predict component structural response.

Quantitating the Absorption, Partitioning and Toxicity of Hydrocarbon Components of JP-8 Jet Fuel

DTIC Science & Technology

2007-08-24

with the skin. AFOSR Jet Fuel Toxicology Workshop. Tucson, AZ. October, 2004. 5. Basak SC, Riviere JE, Baynes RE, Xia XR, Gute BD. A hierarchical QSAR ... Toxicology Workshop, Tucson, AZ, 2005. 12. Basak SC, Riviere J, Baynes R, Gute BD: Theoretical descriptor based QSARs in predicting skin penetration of...NAME(S) AND ADDRESS(ES) 8. PERFORMING ORGANIZATION REPORT NUMBER Center for Chemical Toxicology Research and Pharmacokinetics College of Veterinary

2017 ARL Summer Student Program Volume 2: Compendium of Abstracts

DTIC Science & Technology

2017-12-01

useful for equipping quadrotors with advanced capabilities, such as running deep learning networks. A second purpose of this project is to quantify the...Multiple samples were run in the LEAP 5000-XR generating large data sets (hundreds of millions of ions composing hundreds of cubic nanometers of...produce viable walking and running gaits on the final product. Even further, the monetary and time cost of this increases significantly when working

Heteroepitaxial growth of cadmium carbonate at dolomite and calcite surfaces: Mechanisms and rates

DOE Office of Scientific and Technical Information (OSTI.GOV)

Callagon, Erika Blanca R.; Lee, Sang Soo; Eng, Peter J.

Here, the systematic variation of rates and the mechanism of cadmium uptake on the (104) surface of dolomite (CaMg(CO 3) 2) were investigated using in situ and ex situ atomic force microscopy (AFM), ex situ specular X-ray reflectivity (XR), and ex situ X-ray fluorescence (XRF). Selected experiments were performed on the calcite (CaCO 3) (104) surface for comparison. Aqueous solutions of CdCl 2, CaCl 2, and NaHCO 3, undersaturated with respect to calcite and supersaturated with respect to otavite (CdCO 3) and the (Cd xCa 1-x)CO 3 solid solution, were reacted with dolomite surfaces for minutes to days. Calcite substratesmore » were reacted with solutions containing 1-50 μM CdCl 2, and with no added Ca or CO 3. Thin carbonate films following the Stranski-Krastanov growth mode were observed on both substrates. Specular XR and XRF revealed the formation of nm-thick Cd-rich carbonate films that were structurally ordered with respect to the dolomite (104) plane. Epitaxial films adopted the calcite crystal structure with a d 104- spacing (3.00 Å) larger than those of pure dolomite (2.88 Å) and otavite (2.95 Å) indicating either a solid solution with x approximate to 0.5, or a strained Cd-rich carbonate with a composition near that of otavite. The growth rate r of this phase increases with the initial supersaturation of the solution with respect to the solid solution, beta max, and follows the empirical relationship, as determined from XRF measurements, given by: r = 10 -4.88 ± 0.42 (β 2.29 ± 0.24 max - 1), (in units of atoms of Cd/Å 2/h).The morphology of the overgrowth also varied with β max, as exemplified by AFM observations. Growth at step edges occurred over the entire β max range considered, and additional growth features including 3 Å high monolayer islands and ~ 25 Å high tall islands were observed when log β max > 1. On calcite, in situ XR indicated that this phase is similar to the Cd-rich overgrowth formed on dolomite and images obtained from X-ray reflection interface microscopy (XRIM) reveal the existence of laterally variable Cd-rich domains.« less

Amygdala Reactivity to Emotional Faces in the Prediction of General and Medication-Specific Responses to Antidepressant Treatment in the Randomized iSPOT-D Trial.

PubMed

Williams, Leanne M; Korgaonkar, Mayuresh S; Song, Yun C; Paton, Rebecca; Eagles, Sarah; Goldstein-Piekarski, Andrea; Grieve, Stuart M; Harris, Anthony W F; Usherwood, Tim; Etkin, Amit

2015-09-01

Although the cost of poor treatment outcomes of depression is staggering, we do not yet have clinically useful methods for selecting the most effective antidepressant for each depressed person. Emotional brain activation is altered in major depressive disorder (MDD) and implicated in treatment response. Identifying which aspects of emotional brain activation are predictive of general and specific responses to antidepressants may help clinicians and patients when making treatment decisions. We examined whether amygdala activation probed by emotion stimuli is a general or differential predictor of response to three commonly prescribed antidepressants, using functional magnetic resonance imaging (fMRI). A test-retest design was used to assess patients with MDD in an academic setting as part of the International Study to Predict Optimized Treatment in Depression. A total of 80 MDD outpatients were scanned prior to treatment and 8 weeks after randomization to the selective serotonin reuptake inhibitors escitalopram and sertraline and the serotonin-norepinephrine reuptake inhibitor, venlafaxine-extended release (XR). A total of 34 matched controls were scanned at the same timepoints. We quantified the blood oxygen level-dependent signal of the amygdala during subliminal and supraliminal viewing of facial expressions of emotion. Response to treatment was defined by ⩾50% symptom improvement on the 17-item Hamilton Depression Rating Scale. Pre-treatment amygdala hypo-reactivity to subliminal happy and threat was a general predictor of treatment response, regardless of medication type (Cohen's d effect size 0.63 to 0.77; classification accuracy, 75%). Responders showed hypo-reactivity compared to controls at baseline, and an increase toward 'normalization' post-treatment. Pre-treatment amygdala reactivity to subliminal sadness was a differential moderator of non-response to venlafaxine-XR (Cohen's d effect size 1.5; classification accuracy, 81%). Non-responders to venlafaxine-XR showed pre-treatment hyper-reactivity, which progressed to hypo-reactivity rather than normalization post-treatment, and hypo-reactivity post-treatment was abnormal compared to controls. Impaired amygdala activation has not previously been highlighted in the general vs differential prediction of antidepressant outcomes. Amygdala hypo-reactivity to emotions signaling reward and threat predicts the general capacity to respond to antidepressants. Amygdala hyper-reactivity to sad emotion is involved in a specific non-response to a serotonin-norepinephrine reuptake inhibitor. The findings suggest amygdala probes may help inform the personal selection of antidepressant treatments.

Heteroepitaxial growth of cadmium carbonate at dolomite and calcite surfaces: Mechanisms and rates

DOE PAGES

Callagon, Erika Blanca R.; Lee, Sang Soo; Eng, Peter J.; ...

2016-12-10

Here, the systematic variation of rates and the mechanism of cadmium uptake on the (104) surface of dolomite (CaMg(CO 3) 2) were investigated using in situ and ex situ atomic force microscopy (AFM), ex situ specular X-ray reflectivity (XR), and ex situ X-ray fluorescence (XRF). Selected experiments were performed on the calcite (CaCO 3) (104) surface for comparison. Aqueous solutions of CdCl 2, CaCl 2, and NaHCO 3, undersaturated with respect to calcite and supersaturated with respect to otavite (CdCO 3) and the (Cd xCa 1-x)CO 3 solid solution, were reacted with dolomite surfaces for minutes to days. Calcite substratesmore » were reacted with solutions containing 1-50 μM CdCl 2, and with no added Ca or CO 3. Thin carbonate films following the Stranski-Krastanov growth mode were observed on both substrates. Specular XR and XRF revealed the formation of nm-thick Cd-rich carbonate films that were structurally ordered with respect to the dolomite (104) plane. Epitaxial films adopted the calcite crystal structure with a d 104- spacing (3.00 Å) larger than those of pure dolomite (2.88 Å) and otavite (2.95 Å) indicating either a solid solution with x approximate to 0.5, or a strained Cd-rich carbonate with a composition near that of otavite. The growth rate r of this phase increases with the initial supersaturation of the solution with respect to the solid solution, beta max, and follows the empirical relationship, as determined from XRF measurements, given by: r = 10 -4.88 ± 0.42 (β 2.29 ± 0.24 max - 1), (in units of atoms of Cd/Å 2/h).The morphology of the overgrowth also varied with β max, as exemplified by AFM observations. Growth at step edges occurred over the entire β max range considered, and additional growth features including 3 Å high monolayer islands and ~ 25 Å high tall islands were observed when log β max > 1. On calcite, in situ XR indicated that this phase is similar to the Cd-rich overgrowth formed on dolomite and images obtained from X-ray reflection interface microscopy (XRIM) reveal the existence of laterally variable Cd-rich domains.« less

Nucleotides induce chemotaxis and actin polymerization in immature but not mature human dendritic cells via activation of pertussis toxin-sensitive P2y receptors.

PubMed

Idzko, Marco; Dichmann, Stefan; Ferrari, Davide; Di Virgilio, Francesco; la Sala, Andrea; Girolomoni, Giampiero; Panther, Elisabeth; Norgauer, Johannes

2002-08-01

Dendritic cells (DCs) are considered the principal initiators of immune response because of their ability to migrate into peripheral tissues and lymphoid organs, process antigens, and activate naive T cells. There is evidence that extracellular nucleotides regulate certain functions of DCs via G-protein-coupled P2Y receptors (P2YR) and ion-channel-gated P2X receptors (P2XR). Here we investigated the chemotactic activity and analyzed the migration-associated intracellular signaling events such as actin reorganization and Ca(++) transients induced by common P2R agonists such as adenosine 5'-triphosphate (ATP) and 2-methylthioadenosine triphosphate, the P2YR agonists UTP and adenosine 5'-diphosphate (ADP), or the P2XR agonists alphabeta-methylenadenosine-5'-triphosphate and 2',3'-(4-benzoyl)benzoyl-ATP. The common P2R agonists and the selective P2YR agonists turned out to be potent chemotactic stimuli for immature DCs, but not for mature DCs. In contrast, P2XR agonists had only marginal chemotactic activity in both DC types. Chemotaxis was paralleled by a rise in the intracellular Ca(++) concentration and by actin polymerization. Studies with pertussis toxin implicated that intracellular signaling events such as actin polymerization, mobilization of intracellular Ca(++), and migration induced by nucleotides was mediated via G(i/o) protein-coupled P2YR. Moreover, functional studies revealed selective down-regulation of this G(i/o) protein-coupled chemotactic P2YR responsiveness during maturation, although immature and mature DCs expressed similar amounts of mRNA for the P2R subtypes (P2Y(2)R, P2Y(4)R, P2Y(5)R, P2Y(7)R, P2Y(11)R and P2X(1)R, P2X(4)R, P2X(7)R), and no major differences in respect to the mRNA expression of these receptors could be observed by semiquantitative reverse transcription and polymerase chain reaction (RT-PCR). In summary, our data describe a differential chemotactic response of immature and mature DCs to nucleotides, and lend further support to the hypothesis that P2R are a novel class of immunomodulatory plasma membrane receptors suitable for pharmacological intervention.

A Combinatorial Geometry Computer Description of the XR311 Vehicle

DTIC Science & Technology

1978-04-01

cards or magnetic tape. The shot line output of the GRID subroutine of the GIFT code is also stored on magnetic tape for future vulnera- bility...descriptions as processed by the Geometric Information For Targets ( GIFT )2 computer code. This report documents the COM-GEOM target description for all...72, March 1974. ’L.W. Bains and M.J. Reisinger, "The GIFT Code User Manual, VOL 1, Introduction and Input Requirements, " Ballistic Research

The Utilization of People-Related Navy RDT&E (Research, Development, Test, and Evaluation): Fiscal Year 1978

DTIC Science & Technology

1979-04-01

Results mt •EVrABLUSH TRAINING OBJECTIVES s$ First. the different requirements to be met by an DSVELOPO ThXrINE MEASUMENT ACM performance measurement...engineering Program Element 63722N. guidelines in designing displays, one of the experi- mental innovations of this project will make future Approach and...zation of People-Related RDT&E, published in May decrease motivation and impair efficiency. 1978. 40 Delays in providing initial documentation and in

Insulin and Brain Injury: Memory, Metabolism and Microglia

DTIC Science & Technology

2016-05-20

verbal response and, eye opening. (248) Diagnosis also depends on a general assessment of loss of consciousness ( LOC ), post-injury antero- or...128, 147) According to CDC data, more than 75% of TBI are considered mild. (1) Mild TBI is characterized by the loss of consciousness ( LOC ) not...Stroke 19: 1411-9 128. Leo P, McCrea M. 2016. Epidemiology. 129. Lescot T, Fulla-Oller L, Po C, Chen XR, Puybasset L, et al. 2010. Temporal and

Measurement of computed tomography dose profile with pitch variation using Gafchromic XR-QA2 and thermoluminescence dosimeter (TLD)

NASA Astrophysics Data System (ADS)

Purwaningsih, S.; Lubis, L. E.; Pawiro, S. A.; Soejoko, D. S.

2016-03-01

This research was aimed to check the patterns of dose profile on adult and pediatric head scan. We compared measurement result on dose profile along the z- axis rotation at peripheries and center phantom with a variety of pitch, i.e. 0.75, 1, 1.5 for adult and pediatric head protocol, keeping the rest of the scan parameters constant. Measurements were performed on homogeneous, cylindrical PMMA phantom with diameters of 16 and 10 cm using XR-QA2 Gafchromic film and TLD as dosimeters. The measurement result indicated a decrease in the dose about 50% and 47% for adult and pediatric head scan with the increase of pitch. For 0.75 value of pitch adult head scan, dose range for each position were (2.4 - 5.0) cGy, (3.1 - 5.3) cGy, (2.2 - 4.5) cGy, (2.8 - 5.3) cGy, and (3.3 - 5.6) cGy for position of center, 3, 6, 9 and 12 o'clock peripheral phantom position respectively. Dose profile for adult and pediatric head scan protocols has pattern curve with the maximum dose in the middle and tendency of symmetry near the edges, with different the plateau length along z- axis direction in accordance to the measurement position in the phantom.

Design principles and issues of rights expression languages for digital rights management

NASA Astrophysics Data System (ADS)

Wang, Xin

2005-07-01

Digital rights management (DRM) provides a unified approach to specifying, interpreting, enforcing and managing digital rights throughout the entire life cycle of digital assets. Using a declarative rights expression language (REL) for specifying rights and conditions in the form of licenses, as opposite to some other approaches (such as data structures and imperative languages), has been considered and adopted as a superior technology for implementing effective, interoperable and scalable DRM systems. This paper discusses some principles and issues for designing RELs, based on the experiences of developing a family of REL"s (DPRL, XrML 1.x, XrML 2.0 and MPEG REL). It starts with an overview of a family tree of the past and current REL"s, and their development history, followed by an analysis of their data models and a comparison with access-control oriented models. It then presents a number of primary design principles such as syntactic and semantic un-ambiguity, system interoperability, expressiveness in supporting business models and future extensibility, and discusses a number of key design issues such as maintaining stateful information, multi-tier issuance of rights, meta rights, identification of individual and aggregate objects, late-binding of to-beidentified entities, as well as some advanced ones on revocation and delegation of rights. The paper concludes with some remarks on REL profiling and extension for specific application domains.

Detection and Analysis of X Ray Emission from the Princeton-Field-Reversed Configuration (PFRC-2)

NASA Astrophysics Data System (ADS)

Bosh, Alexandra; Swanson, Charles; Jandovitz, Peter; Cohen, Samuel

2016-10-01

The PFRC is an odd-parity rotating-magnetic-field-driven field-reversed-configuration magnetic confinement experiment. Studying X rays produced via electron Bremsstrahlung with neutral particles is crucial to the further understanding of the energy and particle confinement of the PFRC. The data on the x rays are collected using a detector system comprised of two, spatially scannable Amptek XR-100 CR detectors and a Amptek XR-100 SDD detector that view the plasma column at two axial locations, one in the divertor and one near the axial midplane. These provide X-ray energy and arrival-time information. (Data analysis requires measurement of each detector's efficiency, a parameter that is modified by window transmission. Detector calibrations were performed with a custom-made X-ray tube that impinged 1-microamp 1-5 kV electron beams onto a carbon target.) From the analyzed data, the average electron energy, effective temperature, and electron density can be extracted. Spatial scans then allow the FRC's internal energy to be measured. We present recent measurements of the Bremsstrahlung spectrum from 0.8 to 6 keV and the inferred electron temperature in the PFRC device as functions of heating power, magnetic field and fill gas pressure. This work was supported, in part, by DOE Contract Number DE-AC02-09CH11466.

Altitude-Wind-Tunnel Investigation of R-4360-18 Power-Plant Installation for XR60 Airplane. 3; Performance of Induction and Exhaust Systems

NASA Technical Reports Server (NTRS)

Dupree, David T.; Hawkins, W. Kent

1947-01-01

A study has been made of the performance of the induction and the exhaust systems on the XR60 power-plant installation as part of an investigation conducted in the Cleveland altitude wind tunnel. Altitude flight conditions from 5000 to 30,000 feet were simulated for a range of engine powers from 750 to 3000 brake horsepower. Slipstream rotation prevented normal pressure recoveries in the right side of the main duct in the region of the right intercooler cooling-air duct inlet. Total-pressure losses in the charge-air flow between the turbosupercharger and the intercoolers were as high as 2.1 inches of mercury. The total-pressure distribution of the charge air at the intercooler inlets was irregular and varied as much as 1.0 inch of mercury from the average value at extreme conditions, Total-pressure surveys at the carburetor top deck showed a variation from the average value of 0.3 inch of mercury at take-off power and 0.05 inch of mercury at maximum cruising power, The carburetor preheater system increased the temperature of the engine charge air a maximum of about 82 F at an average cowl-inlet air temperature of 9 F, a pressure altitude of 5000 feet, and a brake horsepower of 1240.

About a method for compressing x-ray computed microtomography data

NASA Astrophysics Data System (ADS)

Mancini, Lucia; Kourousias, George; Billè, Fulvio; De Carlo, Francesco; Fidler, Aleš

2018-04-01

The management of scientific data is of high importance especially for experimental techniques that produce big data volumes. Such a technique is x-ray computed tomography (CT) and its community has introduced advanced data formats which allow for better management of experimental data. Rather than the organization of the data and the associated meta-data, the main topic on this work is data compression and its applicability to experimental data collected from a synchrotron-based CT beamline at the Elettra-Sincrotrone Trieste facility (Italy) and studies images acquired from various types of samples. This study covers parallel beam geometry, but it could be easily extended to a cone-beam one. The reconstruction workflow used is the one currently in operation at the beamline. Contrary to standard image compression studies, this manuscript proposes a systematic framework and workflow for the critical examination of different compression techniques and does so by applying it to experimental data. Beyond the methodology framework, this study presents and examines the use of JPEG-XR in combination with HDF5 and TIFF formats providing insights and strategies on data compression and image quality issues that can be used and implemented at other synchrotron facilities and laboratory systems. In conclusion, projection data compression using JPEG-XR appears as a promising, efficient method to reduce data file size and thus to facilitate data handling and image reconstruction.

Mini-tablets versus pellets as promising multiparticulate modified release delivery systems for highly soluble drugs.

PubMed

Gaber, Dina M; Nafee, Noha; Abdallah, Osama Y

2015-07-05

Whether mini-tablets (tablets, diameters ≤6mm) belong to single- or multiple-unit dosage forms is still questionable. Accordingly, Pharmacopoeial evaluation procedures for mini-tablets are lacking. In this study, the aforementioned points were discussed. Moreover, their potential for oral controlled delivery was assessed. The antidepressant venlafaxine hydrochloride (Vx), a highly soluble drug undergoing first pass effect, low bioavailability and short half-life was selected as a challenging payload. In an attempt to weigh up mini-tablets versus pellets as multiparticulate carriers, Vx-loaded mini-tablets were compared to formulated pellets of the same composition and the innovator Effexor(®)XR pellets. Formulations were prepared using various polymer hydrogels in the core and ethyl cellulose film coating with increasing thickness. Mini-tablets (diameter 2mm) showed extended Vx release (<60%, 8h). Indeed, release profiles comparable to Effexor(®)XR pellets were obtained. Remarkably higher coating thickness was required for pellets to provide equivalent retardation. Ethyl cellulose in the core ensured faster release due to polymer migration to the surface and pore formation in the coat. mini-tablets showed higher stability to pellets upon storage. Industrially speaking, mini-tablets proved to be superior to pellets in terms of manufacturing, product quality and economical aspects. Results point out the urgent need for standardized evaluation procedures for mini-tablets. Copyright © 2015. Published by Elsevier B.V.

[The use of natural and synthetic hydrophilic polymers in the formulation of metformin hydrochloride tablets with different profile release].

PubMed

Kołodziejczyk, Michał Krzysztof; Kołodziejska, Justyna; Zgoda, Marian Mikołaj

2012-01-01

Metformin hydrochloride after buformin and phenformin belongs to the group of biguanid derivatives used as oral anti-diabetic drugs. The object of the study is the technological analysis and the potential effect of biodegradable macromolecular polymers on the technological and therapeutic parameters of oral anti-diabetic medicinal products with metformin hydrochloride: Siofor, Formetic, Glucophage, Metformax in doses of 500mg and 1000mg and Glucophage XR in a dose of 500 mg of modified release. Market therapeutic products containing 500 and 1000 mg of metformin hydrochloride in a normal formulation and 500 mg of metformin hydrochloride in a formulation of modified release were analyzed. Following research methods were used: technological analysis of tablets, study of disintegration time of tablets, evaluation of pharmaceutical availability of metformin hydrochloride from tested therapeutic products, mathematical and kinetic analysis of release profiles of metformin hydrochloride, statistical analysis of mean differences of release coefficients. The percentage of excipients in the XR formulation is higher and constitutes 50.5% of a tablet mass. However, in standard formulations the percentage is lower, between 5.5% and 12.76%. On the basis of the results of disintegration time studies, the analysed therapeutic products can be divided into two groups, regardless the dose. The first one are preparations with faster (not fast!) disintegration: Glucophage i Metformax. The second group are preparations with slower disintegration, more balanced in the aspect of a high dose of the biologically active substance: Formetic and Siofor. Products with a lower content of excipients (Metformax, Glucophage) disintegrate in a faster way. The disintegration rate of the products with a higher content of excipients (Formetic, Siofor) is slower. The appearance of metformin hydrochloride concentration in the gastrointestinal contents, balanced in time, caused by a slower disintegration-dissolving of a tablet, is conducive to the reduction of gastrointestinal side effects and better tolerance of the therapeutic product by a patient. The study on pharmaceutical availability indicated relevant kinetic differences between tested therapeutic products. They are particularly visible between standard formulations and the one with prolonged release (Glucophage XR500). Its release profile bears features of kinetics similar to zero-order reactions. Tested therapeutic products contain a large amount of the biologically active substance in relation to the content of excipients. A higher content of excipients in a single tablet mass distinguishes Siofor in comparison with Glucophage i Metformax. The excipients used in the formulations of tested preparations are comparable. A higher percentage of binding agents (HPMC, PVP) is observed, but there is a lack of typical disintegrants which results in a longer disintegration time up to 15 minutes. Siofor disintegrates at the same time as Formetic, but longer than Glucophage i Metformax. Considering the large content of the active substance and pharmacological properties of metformin hydrochloride, such a disintegration might have beneficial consequences, because the amount of the free active substance in the gastrointestinal tract will increase over the longer time period what will reduce the level of gastrointestinal side effects. The release profiles of metformin hydrochloride from tested therapeutic products are comparable. The Glucophage XR 500 formulation with the release kinetics of metformin hydrochloride similar to the zero-order kinetics is completely different from the others. The above is confirmed by the mathematical analysis of release profiles of metformin hydrochloride from tested preparations where equations of lines describing the release profile are characterized by similar values of correlation coefficients.

Making Space Travel to Jupiter Possible

NASA Technical Reports Server (NTRS)

Barker, Samuel P.

2004-01-01

From man landing on the moon to a simple satellite being launched into orbit, many incredible space accomplishments have been witnessed by us all. However, what goes un-noticed to the common man is the extensive research and testing that lasts months, years, and even decades. Much of this required research just so happens to take place in the corridors of the Glen Research Center building number 49. In the Advanced Materials division of G.R.C., a number of researchers have the responsibility of discovering which metal, ceramic, or polymer is best for a specific application. Under the guidance of mentor extraordinaire Frank Ritzert, I am involved in many critical projects dealing with refractory metals, two of which I will mention in this report. The Jupiter Icy Moons Orbiter (JIMO) project actually was under full swing back in the 50's and early 60's. To enable the 14 year trek to the icy moons of Europa, Callisto, and Ganymede, nuclear propulsion methods were selected. Due to the extreme temperature of the reactor and the extended time period, a refractory metal would need to be implemented. After years of research and progress, the program was suddenly canceled. About a decade ago, the JIMO project was re-instated and now has a goal for departure around 2014. However, a few obstacles lie in our way concerning the use of refractory metals. In certain areas of the orbiter a joint is required between the refractories and other less dense metals. Two of these joints are with nickel based super alloys. Being an intern for Frank Ritzert, the refractory metals expert, I have the opportunity to develop the best method to braze refractory metals to Nickel 201. This involves the actual brazing, electron microscopy and reporting the results. My second project involves a certain part of the orbiter where Niobium 1Zirconium, a refractory metal, is joined with Hastelloy-X a Ni based metal. Small quantities of oxygen, helium and other impurities in the Ni alloy could diffuse into the Nb1Zr causing imbrittlement and possibly major failure. I will be testing the effects of Hast-X on Nb1Zr in a high temperature for 10, 50, 100, and 500 hours. After the samples are run through the heat treatment, strength and chemistry will be tested and reported. My appreciation for the research that goes behind every project has and will continue to grow. By digging through old documents written in the 50's and 60's, scouring through forgotten closets, and learning from those with experience in the refractory metals, I am bound to have an incredible learning experience here at NASA.

Design and fabrication of the Mini-Brayton Recuperator (MBR)

NASA Technical Reports Server (NTRS)

Killackey, J. J.; Graves, R.; Mosinskis, G.

1978-01-01

Development of a recuperator for a 2.0 kW closed Brayton space power system is described. The plate-fin heat exchanger is fabricated entirely from Hastelloy X and is designed for 10 years continuous operation at 1000 K (1300 F) with a Xenon-helium working fluid. Special design provisions assure uniform flow distribution, crucial for meeting 0.975 temperature effectiveness. Low-cycle fatigue, resulting from repeated startup and shutdown cycles, was identified as the most critical structural design problem. It is predicted that the unit has a minimum fatigue life of 220 cycles. This is in excess of the BIPS requirement of 100 cycles. Heat transfer performance and thermal cycle testing with air, using a prototype unit, verified that all design objectives can be met.

Production test IP-376-D, Supplement B Irradiation of MGCR-HDR-3 Test Element

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baars, R.E.

The objective of this supplement to PT-IP-376-D, Irradiation of MGCR-HDR-3 Test Element is to authorize 1000 hours of operation at a maximum test specimen surface temperature of 1700 F. The original production test authorized a test duration of four months at a maximum specimen surface temperature of 1500 F; supplement A authorized extension of the test duration to ten months. The desired increase in surface temperature is requested to demonstrate the general feasibility of operation of the fuel element at 1700 F, and to obtain specific information on the performance of Hastelloy-X cladding and fuel bodies. The increased temperature hasmore » been approved by the Atomic Energy Commission.« less

Healing of Stress Fracture in an Animal Model

DTIC Science & Technology

2005-09-01

result of damage in vivo [1,15]. (with hydroxyl ions) at the surface of the hydroxyapatite crystal 54 35 Recently, we have found that positron emission...after loading. Scale bar = 500 pm. 4 1 Li ef al. / Bone xr (2005) xtx-xxv A B C -Comparison of Fatigue Loading with Loading without Fatigue AOL 2.0, I.O...groups in the hydroxyapatite crystal . a t P 3 267 of bone to form fluoroapatite. [𔃿 F]fluoride is deposited pre- The authors would like totha;lnBce Mock

Effects of radiation pressure on the equipotential surfaces in X-ray binaries

NASA Technical Reports Server (NTRS)

Kondo, Y.; Mccluskey, G. E., Jr.; Gulden, S. L.

1976-01-01

Equipotential surfaces incorporating the effect of radiation pressure were computed for the X-ray binaries Cen X-3, Cyg X-1 = HDE 226868, Vela XR-1 = 3U 0900-40 = HD 77581, and 3U 1700-37 = HD 153919. The topology of the equipotential surfaces is significantly affected by radiation pressure. In particular, the so-called critical Roche (Jacobian) lobes, the traditional figure 8's, do not exist. The effects of these results on modeling X-ray binaries are discussed.

Controlled-Release Personal Use Arthropod Repellent Formulation. Phase 3

DTIC Science & Technology

1987-08-26

Polyethylene Glycol (200) Glyceryl Monotallowate (Varonic L1420) 54.2 lbs. Glyceryl Stearate/ Sodium Lauryl Sulfate (Lexemul AS) 129.3 lbs. Propylene... Sulfate 6-0 Xr ________ (Le.ernul AS) - 0.65__ * 13W00 Cetyl Palmitate (W,xenol 816) 2,600 Xg. Ci Zq! 167 2.2___ 10026 Poyproplen Gycol (15) Stenryl...1 Stearate7Sodium lAu 1l Sulfate T- 4fIa- TW _ - ________ Lex emul AS)__________ ____ _______ 2.41 11315 /Prop lene Glycol D1 cap" lateDf~caerate

A Description of the Framework of the Atmospheric Boundary Layer Environment (ABLE) Model

DTIC Science & Technology

2012-09-01

difference scheme (CDS). For the mass flux through the face e of CV, mUDSe CDS e UDS ee QQQQ )(  . (16) The superscript m again means that...PEPee xr  , zyCUQ EEE   , and the lowercase subscripts represents the advective fluxes at the corresponding faces of control volume...WP wW PE eE WP WP wPwW PE PE eEeP we we xx zyD FC xx zyD

Review of Fusion Systems and Contributing Technologies for SIHS-TD (Examen des Systemes de Fusion et des Technologies d’Appui pour la DT SIHS)

DTIC Science & Technology

2007-03-31

Unlimited, Nivisys, Insight technology, Elcan, FLIR Systems, Stanford photonics Hardware Sensor fusion processors Video processing boards Image, video...Engineering The SPIE Digital Library is a resource for optics and photonics information. It contains more than 70,000 full-text papers from SPIE...conditions Top row: Stanford Photonics XR-Mega-10 Extreme 1400 x 1024 pixels ICCD detector, 33 msec exposure, no binning. Middle row: Andor EEV iXon

Lobster eye as a collector for water window microscopy

NASA Astrophysics Data System (ADS)

Pina, L.; Maršíková, V.; Inneman, A.; Nawaz, M. F.; Jančárek, A.; Havlíková, R.

2017-08-01

Imaging in EUV, SXR and XR spectral bands of radiation is of increasing interest. Material science, biology and hot plasma are examples of relevant fast developing areas. Applications include spectroscopy, astrophysics, Soft X-ray Ray metrology, Water Window microscopy, radiography and tomography. Especially Water Window imaging has still not fully recognized potential in biology and medicine microscopy applications. Theoretical study and design of Lobster Eye (LE) optics as a collector for water window (WW) microscopy and comparison with a similar size ellipsoidal mirror condensor are presented.

Experimental Validation of a Time-Accurate Finite Element Model for Coupled Multibody Dynamics and Liquid Sloshing

DTIC Science & Technology

2007-04-16

velocity of the fluid mesh, P is the relative pressure, xr is the position vector, τ is the deviatoric stress tensor, D is the rate of deformation...corresponds to a slip factor of zero. The slip factor determines how much of the fluid and structure forces are mutually exchanged. Equations 22 and 23...updated from last to first. viii.Average the fluid pressure (This step eliminates the pressure checker-boarding effect and allows use of equal

Nontraditional Intelligence, Surveillance, and Reconnaissance: Making the Most of Airborne Assets

DTIC Science & Technology

2015-10-01

Constrained Budgets,” White paper, 4. 36. Ibid., 3 . 37. Ibid., 4. 38. This pod would not include integration on “stealth” aircraft for obvious reasons. 39...sortie flow showing planned XCAS/convoy escort sorties 6 3 VDL-equipped Sniper XR/ATP 7 4 PED management team organization 9 vii Foreword It...platforms and capabilities. 3 In general, the military has a poor historical record when it comes to predicting who the adversary will be, what it

Phase I. Lanthanum-based Start Materials for Hydride Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gschneidner, K. A.; Schmidt, F. A.; Frerichs, A. E.

The purpose of Phase I of this work is to focus on developing a La-based start material for making nickel-metal (lanthanum)-hydride batteries based on our carbothermic-silicon process. The goal is to develop a protocol for the manufacture of (La 1-xR x)(Ni 1-yM y)(Si z), where R is a rare earth metal and M is a non-rare earth metal, to be utilized as the negative electrode in nickel-metal hydride (NiMH) rechargeable batteries.

Relaxation and Self-Diffusion of a Polymer Chain in a Melt

NASA Astrophysics Data System (ADS)

Hagita, Katsumi; Takano, Hiroshi

2004-04-01

Relaxation and self-diffusion of a polymer chain in a melt are discussed on the basis of the results of our recent Monte Carlo simulations of the bond fluctuation model, where only the excluded volume interaction is considered. Polymer chains are located on an L × L × L simple cubic lattice under periodic boundary conditions. Each chain consists of N segments, each of which occupies 2 × 2 × 2 unit cells. The results for N = 32, 48, 64, 96, 128, 192, 256, 384 and 512 at the volume fraction φ ≃ 0.5 are examined, where L = 128 for N ⩽ 256 and L = 192 for N ⩾ 384. The longest relaxation time τ is estimated by solving generalized eigenvalue problems for the equilibrium time correlation matrices of the positions of segments of a polymer chain. The self-diffusion constant D is estimated from the mean square displacements of the center of mass of a single polymer chain at the times larger than τ. From the data for N = 256, 384 and 512, the apparent exponents x r and xd, which describe the power law dependences of τ and D on N as τ ∝ N xr and D ∝ N-xd, are estimated to be xr ≃ 3.5 and xd ≃ 2.4, respectively. For N = 192, 256, 384 and 512, Dτ/ appears to be a constant, where denotes the mean square end-to-end distance of a polymer chain.

Baseline Characteristics of Patients Predicting Suitability for Rapid Naltrexone Induction

PubMed Central

Mogali, Shanthi; Khan, Nabil A.; Drill, Esther S.; Pavlicova, Martina; Sullivan, Maria A.; Nunes, Edward; Bisaga, Adam

2015-01-01

Background and Objectives Extended-release (XR) injection naltrexone has proved promising in the treatment of opioid dependence. Induction onto naltrexone is often accomplished with a procedure known as rapid naltrexone induction. The purpose of this study was to evaluate pre-treatment patient characteristics as predictors of successful completion of a rapid naltrexone induction procedure prior to XR naltrexone treatment. Methods A chart review of 150 consecutive research participants (N = 84 completers and N = 66 non-completers) undergoing a rapid naltrexone induction with the buprenorphone-clonidine procedure were compared on a number of baseline demographic, clinical and psychosocial factors. Logistic regression was used to identify client characteristics that may predict successful initiation of naltrexone after a rapid induction-detoxification. Results Patients who failed to successfully initiate naltrexone were younger (AOR: 1.040, CI: 1.006, 1.075), and using 10 or more bags of heroin (or equivalent) per day (AOR: 0.881, CI: 0.820, 0.946). Drug use other than opioids was also predictive of failure to initiate naltrexone in simple bivariate analyses, but was no longer significant when controlling for age and opioid use level. Conclusions Younger age, and indicators of greater substance dependence severity (more current opioid use, other substance use) predict difficulty completing a rapid naltrexone induction procedure. Such patients might require a longer period of stabilization and/or more gradual detoxification prior to initiating naltrexone. Scientific Significance Our study findings identify specific characteristics of patients who responded positively to rapid naltrexone induction. PMID:25907815

Engineering of Corynebacterium glutamicum for xylitol production from lignocellulosic pentose sugars.

PubMed

Dhar, Kiran S; Wendisch, Volker F; Nampoothiri, Kesavan Madhavan

2016-07-20

Xylitol is a non-fermentable sugar alcohol used as sweetener. Corynebacterium glutamicum ATCC13032 was metabolically engineered for xylitol production from the lignocellulosic pentose sugars xylose and arabinose. Direct conversion of xylose to xylitol was achieved through the heterologous expression of NAD(P)H-dependent xylose reductase (xr) gene from Rhodotorula mucilaginosa. Xylitol synthesis from arabinose was attained through polycistronic expression of l-arabinose isomerase (araA), d-psicose 3 epimerase (dpe) and l-xylulose reductase (lxr) genes from Escherichia coli, Agrobacterium tumefaciens and Mycobacterium smegmatis, respectively. Expression of xr and the synthetic araA-dpe-lxr operon under the control of IPTG-inducible Ptac promoter enabled production of xylitol from both xylose and arabinose in the mineral (CGXII) medium with glucose as carbon source. Additional expression of a pentose transporter (araTF) gene enhanced xylitol production by about four-fold compared to the parent strain. The constructed strain Cg-ax3 produced 6.7±0.4g/L of xylitol in batch fermentations and 31±0.5g/L of xylitol in fed-batch fermentations with a specific productivity of 0.28±0.05g/g cdw/h. The strain Cg-ax3 was also validated for xylitol production from pentose rich, acid pre-treated liquor of sorghum stover (SAPL) and the results were comparable in both SAPL (27±0.3g/L) and mineral medium (31±0.5g/L). Copyright © 2016 Elsevier B.V. All rights reserved.

Amygdala Reactivity to Emotional Faces in the Prediction of General and Medication-Specific Responses to Antidepressant Treatment in the Randomized iSPOT-D Trial

PubMed Central

Williams, Leanne M; Korgaonkar, Mayuresh S; Song, Yun C; Paton, Rebecca; Eagles, Sarah; Goldstein-Piekarski, Andrea; Grieve, Stuart M; Harris, Anthony W F; Usherwood, Tim; Etkin, Amit

2015-01-01

Although the cost of poor treatment outcomes of depression is staggering, we do not yet have clinically useful methods for selecting the most effective antidepressant for each depressed person. Emotional brain activation is altered in major depressive disorder (MDD) and implicated in treatment response. Identifying which aspects of emotional brain activation are predictive of general and specific responses to antidepressants may help clinicians and patients when making treatment decisions. We examined whether amygdala activation probed by emotion stimuli is a general or differential predictor of response to three commonly prescribed antidepressants, using functional magnetic resonance imaging (fMRI). A test–retest design was used to assess patients with MDD in an academic setting as part of the International Study to Predict Optimized Treatment in Depression. A total of 80 MDD outpatients were scanned prior to treatment and 8 weeks after randomization to the selective serotonin reuptake inhibitors escitalopram and sertraline and the serotonin–norepinephrine reuptake inhibitor, venlafaxine-extended release (XR). A total of 34 matched controls were scanned at the same timepoints. We quantified the blood oxygen level-dependent signal of the amygdala during subliminal and supraliminal viewing of facial expressions of emotion. Response to treatment was defined by ⩾50% symptom improvement on the 17-item Hamilton Depression Rating Scale. Pre-treatment amygdala hypo-reactivity to subliminal happy and threat was a general predictor of treatment response, regardless of medication type (Cohen's d effect size 0.63 to 0.77; classification accuracy, 75%). Responders showed hypo-reactivity compared to controls at baseline, and an increase toward ‘normalization' post-treatment. Pre-treatment amygdala reactivity to subliminal sadness was a differential moderator of non-response to venlafaxine-XR (Cohen's d effect size 1.5; classification accuracy, 81%). Non-responders to venlafaxine-XR showed pre-treatment hyper-reactivity, which progressed to hypo-reactivity rather than normalization post-treatment, and hypo-reactivity post-treatment was abnormal compared to controls. Impaired amygdala activation has not previously been highlighted in the general vs differential prediction of antidepressant outcomes. Amygdala hypo-reactivity to emotions signaling reward and threat predicts the general capacity to respond to antidepressants. Amygdala hyper-reactivity to sad emotion is involved in a specific non-response to a serotonin–norepinephrine reuptake inhibitor. The findings suggest amygdala probes may help inform the personal selection of antidepressant treatments. PMID:25824424

The 3D distribution of cordierite and biotite in hornfels from the Bugaboo contact aureole (British Columbia, Canada)

NASA Astrophysics Data System (ADS)

Gaidies, Fred; Petley-Ragan, Arianne; Pattison, David

2016-04-01

The size, abundance, shape and spatial distribution of metamorphic minerals bears important information on the rates and mechanisms of fundamental processes that take place during metamorphic crystallization. X-ray computed tomography (XR-CT) has become the method of choice to study the three-dimensional (3D) disposition of minerals in rocks as it allows investigation of relatively large sample volumes at sufficiently high resolution required for statistically meaningful analyses, and as its non-destructive fashion permits further studies such as mineral chemical, isotopic or crystallographic analyses of select grains identified through XR-CT. We present results obtained through the quantification of the 3D disposition of cordierite and biotite crystals in a hornfels from the contact aureole of the Bugaboo Batholith (British Columbia, Canada) using XR-CT and global as well as scale-dependent pattern statistics (Petley-Ragan et al., 2016). The results demonstrate a random distribution of cordierite and biotite crystal sizes for all scales across the entire rock volume studied indicative of interface-controlled prograde metamorphic reaction kinetics. We show that the common approach to approximate the shape of crystals as spherical underestimates the influence of the Strauss hard-core process on rock texture which may be misinterpreted to reflect ordering of crystal sizes by inhibition of nucleation and growth commonly associated with diffusion-controlled reaction kinetics. According to our findings, Strauss hard-core ordering develops at length scales equal to and less than the average major axis of the crystal population. This is significantly larger than what is obtained if a spherical crystal geometry would be assumed, and increases with deviation from sphericity. For the cordierite and biotite populations investigated in this research, Strauss hard-core ordering developed at length scales of up to ˜2.2 and 1.25 mm, respectively, which is almost 1 mm longer than the scales that would be obtained if a spherical geometry would have been assumed. Our results highlight the importance of a critical assessment of the geometrical model assumptions commonly applied in the 3D analysis of crystal size distributions, and underline the need for a quantitative understanding of interface processes in order to appreciate their role in the kinetics of contact metamorphic reactions and rock texture formation. References: Petley-Ragan A, Gaidies F, Pattison DRM (2016) A statistical analysis of the distribution of cordierite and biotite in hornfels from the Bugaboo contact aureole: implications for the kinetics of porphyroblast crystallization. Journal of Metamorphic Geology 34:85-101

Nonlinear constitutive theory for turbine engine structural analysis

NASA Technical Reports Server (NTRS)

Thompson, R. L.

1982-01-01

A number of viscoplastic constitutive theories and a conventional constitutive theory are evaluated and compared in their ability to predict nonlinear stress-strain behavior in gas turbine engine components at elevated temperatures. Specific application of these theories is directed towards the structural analysis of combustor liners undergoing transient, cyclic, thermomechanical load histories. The combustor liner material considered in this study is Hastelloy X. The material constants for each of the theories (as a function of temperature) are obtained from existing, published experimental data. The viscoplastic theories and a conventional theory are incorporated into a general purpose, nonlinear, finite element computer program. Several numerical examples of combustor liner structural analysis using these theories are given to demonstrate their capabilities. Based on the numerical stress-strain results, the theories are evaluated and compared.

Heat pipes for wing leading edges of hypersonic vehicles

NASA Technical Reports Server (NTRS)

Boman, B. L.; Citrin, K. M.; Garner, E. C.; Stone, J. E.

1990-01-01

Wing leading edge heat pipes were conceptually designed for three types of vehicle: an entry research vehicle, aero-space plane, and advanced shuttle. A full scale, internally instrumented sodium/Hastelloy X heat pipe was successfully designed and fabricated for the advanced shuttle application. The 69.4 inch long heat pipe reduces peak leading edge temperatures from 3500 F to 1800 F. It is internally instrumented with thermocouples and pressure transducers to measure sodium vapor qualities. Large thermal gradients and consequently large thermal stresses, which have the potential of limiting heat pipe life, were predicted to occur during startup. A test stand and test plan were developed for subsequent testing of this heat pipe. Heat pipe manufacturing technology was advanced during this program, including the development of an innovative technique for wick installation.

Optical Laser Technology, Specifically CD-ROM (Compact Disc - Read Only Memory) and Its Application to the Storage and Retrieval of Information.

DTIC Science & Technology

1987-06-01

RESOLUTION TEST CHART NATIONAL BUREAU OF STANDARIS-1963-A gT~ ILE CE NAVAL POSTGRADUATE SCHOOL Monterey, California ;.CTE THESIS uEOIB OPTICAL LASER... usedin it xr~awsd SECURITY CLASSIFICATION Of ’-IS5 PACTF All other edtoni are obsolete 0’ NC TA? 7RI UNCLASSIFIED S3CUNTY CLASSIFICATION OF THIS PA69 (WhI...where the resulting mixture of text, color graphics, animation , and audio can be achieved. This technology is in the formative stages, however it is

A Fundamental Investigation of Crack and Surrounding Damage in Stiff Clays

DTIC Science & Technology

1988-09-01

equation of state is written in terms of entropy production. A generalized flux is identified as the centroidal movement of the damage zone, and the...on the following governing equation. I I a14 ( 1.1] Ti = z ’_Xc + "_.wXrOt + a.’X ef = 0 where Si is the global entropy production, 1, , and a are...convenient to express the internal energy density u in terms of i Gibb’s potential density and the entropy density s [6.3] u = g + Ts +’ijciji Here

Studies on Optimized Assured Cooperative Communications

DTIC Science & Technology

2014-04-01

a corresponding vector xr = [ −x∗ s ,2 x∗ s ,1 ] . The received signal yd, m at the destination at the m -th H-ARQ (re)transmission round with relay...3 15.54 15.48 21.65 28.30 15.05 s ,1 s ,2 r 0 100 200 300 400 500 600 700 800 900 1000 Transmission round index T ra ns m is si on p ow er P s , l a nd...ns m is si on p ow er P s , l a nd P r Equal power assignment

ACTIVE: Activity Concept Transitions in Video Event Classification (Open Access)

DTIC Science & Technology

2014-03-03

responses are listed under each event. [2] R.- E . Fan, K.-W. Chang, C.-J. Hsieh, X.-R. Wang, and C.-J. Lin. LIBLINEAR: A library for large linear...Laptev, M. Marszalek, C. Schmid, and B. Rozenfeld. Learning realistic human actions from movies. In CVPR, 2008. 1 [11] L.-J. Li, H. Su, E . P. Xing, and F...invariant keypoints. IJCV, 60(2):91–110, 2004. 1, 2 [14] P. Natarajan, S. Vitaladevuni, U. Park, S. Wu, V. Manohar, X. Zhuang, S. Tsakalidis , R. Prasad, and P

Accuracy Assessment for the Auxillary Tracking System

DTIC Science & Technology

1991-09-01

Auxiliary Tracking System (ATS), paper prepared for evaluation of ATS design review, 28 June, 1990. Anton , H., and Rorres, C., Elementary Linear Algebra with...are linearized around the trial value (XT6, YT,, Zro), shown in Equation 3.16, where 10 means evaluated at point "o". The OR1aI * YaT- I T.) ZR (ZT...3.16) partial derivatives are listed in Equations 3.17 through 3.19. 8XR.[ o 7.-OR1 [ .XT-XL (3.17) aOR., ZTo-Z 1 (3.19) aZTIo R. The linearized

Superconductivity in ABa 2Cu 3O 7-x compounds, where A = (R 1) x(R 2) 1-x and R1, R2 = Y, Sm, Eu, Gd, Tb, Dy, Yb, Zr, Nb AND La

NASA Astrophysics Data System (ADS)

Poddar, A.; Mandal, P.; Choudhury, P.; Das, A. N.; Ghosh, B.

1988-06-01

The electrical resistance has been measured for the titled compounds. All the compounds show superconductivity at about 90 K except La-system whose superconducting behavior depends much on the preparation procedure. Magnetization measurements has been made at 77 K and the Hmax (field at which negative magnetization is maximum) values for the above systems are in the range 170 - 320 Oe.

Monomolecular Siloxane Film as a Model of Single Site Catalysts

DOE PAGES

Martynowycz, Michael W.; Hu, Bo; Kuzmenko, Ivan; ...

2016-09-06

Achieving structurally well-defined catalytic species requires a fundamental understanding of surface chemistry. Detailed structural characterization of the catalyst binding sites in situ, such as single site catalysts on silica supports, is technically challenging or even unattainable. Octadecyltrioxysilane (OTOS) monolayers formed from octadecyltrimethoxysilane (OTMS) at the air-liquid interface after hydrolysis and condensation at low pH were chosen as a model system of surface binding sites in silica-supported Zn 2+ catalysts. We characterize the system by grazing incidence X-ray diffraction, X-ray reflectivity (XR), and X-ray fluorescence spectroscopy (XFS). Previous X-ray and infrared surface studies of OTMS/OTOS films at the airliquid interface proposedmore » the formation of polymer OTOS structures. According to our analysis, polymer formation is inconsistent with the X-ray observations and structural properties of siloxanes; it is energetically unfavorable and thus highly unlikely. We suggest an alternative mechanism of hydrolysis/condensation in OTMS leading to the formation of structurally allowed cyclic trimers with the six-membered siloxane rings, which explain well both the X-ray and infrared results. XR and XFS consistently demonstrate that tetrahedral [Zn(NH 3) 4] 2+ ions bind to hydroxyl groups of the film at a stoichiometric ratio of OTOS:Zn ~ 2:1. The high binding affinity of zinc ions to OTOS trimers suggests that the six-membered siloxane rings are binding locations for single site Zn/SiO 2 catalysts. Finally, our results show that OTOS monolayers may serve as a platform for studying silica surface chemistry or hydroxyl-mediated reactions.« less

Food losses, shelf life extension and environmental impact of a packaged cheesecake: A life cycle assessment.

PubMed

Gutierrez, Michele Mario; Meleddu, Marta; Piga, Antonio

2017-01-01

Packaging is associated with a high environmental impact. This is also the case in the food industry despite packaging being necessary for maintaining food quality, safety assurance and preventing food waste. The aim of the present study was to identify improvements in food packaging solutions able to minimize environmental externalities while maximizing the economic sustainability. To this end, the life cycle assessment (LCA) methodology was applied to evaluate the environmental performance of new packaging solutions. The environmental impact of packaging and food losses and the balance between the two were examined in relation to a cheesecake that is normally packaged in low density polyethylene film and has a limited shelf life due to microbial growth. A shelf life extension was sought via application of the well-established modified atmosphere packaging (MAP) technique. Samples for MAP (N 2 /CO 2 : 70/30) were placed inside multilayer gas barrier trays, which were then wrapped with a multilayer gas and water barrier film (i.e. AerPack packaging); control batches were packaged in gas barrier recycled polyethylene terephthalate (XrPet) trays and wrapped with a XrPet film. Samples were then stored at 20°C and inspected at regular intervals for chemical-physical, microbiological and sensory parameters. Results show that the new packaging solution could considerably extend the shelf life of cheesecakes, thereby reducing food waste and decreasing the overall environmental impact. Moreover, the new packaging allows one to minimize transport costs and to generate economies of scale in manufacturing. Copyright © 2016 Elsevier Ltd. All rights reserved.

Electronic properties of thiolate compounds of oxomolybdenum(V) and their tungsten and selenium analogues. Effects of /sup 17/O, /sup 98/Mo, and /sup 95/Mo isotope substitution upon ESR spectra

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hanson, G.R.; Brunette, A.A.; McDonell, A.C.

1981-04-22

The series of crystalline, mononuclear B/sup +/(MO(XR)/sub 4/)/sup -/ and triply bridged binuclear B/sup +/(M/sub 2/O/sub 2/(XR)/sub 6/(OMe))/sup -/(M = Mo, W; X = S, Se; R = aryl; B = quaternary cation) salts have been isolated and the anions (MoO(SR)/sub 4/)/sup -/ (R = Et, CH/sub 2/Ph) stabilized in solution at -60/sup 0/C. The mononuclear anions are intensely colored due to a ligand-to-metal charge-transfer transition which is absent in the binuclear species. The magnetic susceptibilities of (Et/sub 4/N)(MO(SPh)/sub 4/) show a Curie dependence in the range 300 to 4.2 K with minor deviations in the tungsten compound. The behaviormore » is essentially that of magnetically dilute 4d/sup 1/ and 5d/sup 1/ systems exhibiting a tetragonal ligand field and greatly reduced spin-orbit coupling on the metal. The presence of strong spin-spin coupling in the binuclear compounds leads to magnetic moments close to 0. ESR spectra (at X- and Q-band frequencies) of the mononuclear anions exhibit axial symmetry, and /sup 98/Mo and /sup 95/Mo isotope substitution and computer simulation permit accurate extraction of the g and hyperfine tensor anisotropies. Exceptionally arrow line widths permit observation of /sup 17/O-superhyperfine coupling in /sup 17/O-enriched (/sup 98/MoO(SPh)/sub 4/)/sup -/(a = 2.2 x 10/sup -4/cm/sup -1/).« less

Common aperture multispectral spotter camera: Spectro XR

NASA Astrophysics Data System (ADS)

Petrushevsky, Vladimir; Freiman, Dov; Diamant, Idan; Giladi, Shira; Leibovich, Maor

2017-10-01

The Spectro XRTM is an advanced color/NIR/SWIR/MWIR 16'' payload recently developed by Elbit Systems / ELOP. The payload's primary sensor is a spotter camera with common 7'' aperture. The sensor suite includes also MWIR zoom, EO zoom, laser designator or rangefinder, laser pointer / illuminator and laser spot tracker. Rigid structure, vibration damping and 4-axes gimbals enable high level of line-of-sight stabilization. The payload's list of features include multi-target video tracker, precise boresight, strap-on IMU, embedded moving map, geodetic calculations suite, and image fusion. The paper describes main technical characteristics of the spotter camera. Visible-quality, all-metal front catadioptric telescope maintains optical performance in wide range of environmental conditions. High-efficiency coatings separate the incoming light into EO, SWIR and MWIR band channels. Both EO and SWIR bands have dual FOV and 3 spectral filters each. Several variants of focal plane array formats are supported. The common aperture design facilitates superior DRI performance in EO and SWIR, in comparison to the conventionally configured payloads. Special spectral calibration and color correction extend the effective range of color imaging. An advanced CMOS FPA and low F-number of the optics facilitate low light performance. SWIR band provides further atmospheric penetration, as well as see-spot capability at especially long ranges, due to asynchronous pulse detection. MWIR band has good sharpness in the entire field-of-view and (with full HD FPA) delivers amount of detail far exceeding one of VGA-equipped FLIRs. The Spectro XR offers level of performance typically associated with larger and heavier payloads.

The GA sulfur-iodine water-splitting process - A status report

NASA Astrophysics Data System (ADS)

Besenbruch, G. E.; Chiger, H. D.; McCorkle, K. H.; Norman, J. H.; Rode, J. S.; Schuster, J. R.; Trester, P. W.

The development of a sulfur-iodine thermal water splitting cycle is described. The process features a 50% thermal efficiency, plus all liquid and gas handling. Basic chemical investigations comprised the development of multitemperature and multistage sulfuric acid boost reactors, defining the phase behavior of the HI/I2/H2O/H3PO4 mixtures, and development of a decomposition process for hydrogen iodide in the liquid phase. Initial process engineering studies have led to a 47% efficiency, improvements of 2% projected, followed by coupling high-temperature solar concentrators to the splitting processes to reduce power requirements. Conceptual flowsheets developed from bench models are provided; materials investigations have concentrated on candidates which can withstand corrosive mixtures at temperatures up to 400 deg K, with Hastelloy C-276 exhibiting the best properties for containment and heat exchange to I2.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thompson, Cyril V.; Whitten, William B.

This report describes Oak Ridge National Laboratory’s (ORNL) FY15 progress in support of National Nuclear Security Administration’s (NNSA) Portable Mass Spectrometer project. A retrofit PolarisQ ion trap mass spectrometer (RPMS) has been assembled from components of two PolarisQ ion trap mass spectrometers used in previous isotope ratio programs. The retrofit mass spectrometer includes a custom Hastelloy vacuum chamber which is about ¼ the size of the standard aluminum vacuum chamber and reduces the instrument weight from the original by nine pounds. In addition, the new vacuum chamber can be independently heated to reduce impurities such as water, which reacts withmore » UF 6 to produce HF in the vacuum chamber. The analyzer and all components requiring service are mounted on the chamber lid, facilitating quick and easy replacement of consumable components such as the filament and electron multiplier.« less

The GA sulfur-iodine water-splitting process - A status report

NASA Technical Reports Server (NTRS)

Besenbruch, G. E.; Chiger, H. D.; Mccorkle, K. H.; Norman, J. H.; Rode, J. S.; Schuster, J. R.; Trester, P. W.

1981-01-01

The development of a sulfur-iodine thermal water splitting cycle is described. The process features a 50% thermal efficiency, plus all liquid and gas handling. Basic chemical investigations comprised the development of multitemperature and multistage sulfuric acid boost reactors, defining the phase behavior of the HI/I2/H2O/H3PO4 mixtures, and development of a decomposition process for hydrogen iodide in the liquid phase. Initial process engineering studies have led to a 47% efficiency, improvements of 2% projected, followed by coupling high-temperature solar concentrators to the splitting processes to reduce power requirements. Conceptual flowsheets developed from bench models are provided; materials investigations have concentrated on candidates which can withstand corrosive mixtures at temperatures up to 400 deg K, with Hastelloy C-276 exhibiting the best properties for containment and heat exchange to I2.

Demonstration of the Origin of Human Mast Cells from CD34+ Bone Marrow Progenitor Cells

DTIC Science & Technology

1991-03-01

culture media sexi -ral tixixesovxer the agaxosc surf-~c. Total poured off, anid the reixiiig adherenxt cells were -cultured In cornm- cell counts were...ined bilue . Resi ills we-re explressed xis Itire percent Iage of cit her noxrmalx goat sern o xr gx xx IgGO (0,5 i, ’ ) I Ix at room cells st...hixIxri- aiixre - ;it ixialer lysis w%*is per-~- foxrmed ’loxverify the rcinxv~dl xIli- (1)2. (1119 ixx ("D2(1. 4A 17,oxr (𔃻)1. p it cells

Mitigation of Shore Damage Attributed to the Federal Navigation Structures at Hammond Bay Harbor.

DTIC Science & Technology

1976-11-01

34.’,u:e bz ma :’s Winter wren :,. UsatN2II Golden crown kinglet , f, cI’OPuM Cedar waxwing ’ ’’w .": x?,r’ ,7jq Northern shrike * , ~ PIPar Starling...flycatcher Pct-,hlidon Bank swallows Progue sabis Purple martins Troo Zodytes aedon House wren Dv,,’tolZa oaroliensis Catbird T ,xosterna rufern Brown...and Related Land Resources b the Wic ’ , sir ,S ,ounci 1. S. ai 9.t Mr. and Mi_rs. Joseph__ Mser I. Comment: We have read the environin.ntaIl impact

RX: a nonimaging concentrator.

PubMed

Miñano, J C; Benítez, P; González, J C

1995-05-01

A detailed description of the design procedure for a new concentrator, RX, and some examples of it's use are given. The method of design is basically the same as that used in the design of two other concentrators: the RR and the XR [Appl. Opt. 31, 3051 (1992)]. The RX is ideal in two-dimensional geometry. The performance of the rotational RX is good when the average angular spread of the input bundle is small: up to 95% of the power of the input bundle can be transferred to the output bundle (with the assumption of a constant radiance for the rays of the input bundle).

[Evaluation of YAG-laser vitreolysis effectiveness based on quantitative characterization of vitreous floaters].

PubMed

Shaimova, V A; Shaimov, T B; Shaimov, R B; Galin, A Yu; Goloshchapova, Zh A; Ryzhkov, P K; Fomin, A V

2018-01-01

To develop methods for evaluating effectiveness of YAG-laser vitreolysis of vitreous floaters. The study included 144 patients (173 eyes) who had underwent YAG-laser vitreolysis and were under observation from 01.09.16 to 31.01.18. The patients were 34 to 86 years old (mean age 62.7±10.2 years), 28 (19.4%) patients were male, 116 (80.6%) - female. All patients underwent standard and additional examination: ultrasonography (Accutome B-scan plus, U.S.A.), optic biometry (Lenstar 900, Haag-Streit, Switzerland), spectral optical coherence tomography using RTVue XR Avanti scanner (Optovue, U.S.A.) in modes Enhanced HD Line, 3D Retina, 3D Widefield MCT, Cross Line, Angio Retina, and scanning laser ophthalmoscopy (SLO) using Navilas 577s system. Laser vitreolysis was performed using the Ultra Q Reflex laser (Ellex, Australia). This paper presents methods of objective quantitative and qualitative assessment of artifactual shadows of vitreous floaters with spectral optical coherence tomographic scanner RTVue xR Avanti employing an algorithm of automatic detection of non-perfusion zones in modes Angio Retina, HD Angio Retina, as well as foveal avascular zone (FAZ) measurement with Angio Analytics® software. SLO performed with Navilas 577s was used as method of visualizing floaters and artifactual shadows in retinal surface layers prior to surgical treatment and after YAG-laser vitreolysis. Suggested methods of quantitative and qualitative assessment of artifactual shadows of the floaters in retinal layers are promising and may prove to be highly relevant for clinical monitoring of patients, optimization of treatment indications and evaluating effectiveness of YAG-laser vitreolysis. Further research of laser vitreolysis effectiveness in patients with vitreous floaters is necessary.

Effects of developer exhaustion on the sensitometric properties of four dental films.

PubMed

Syriopoulos, K; Velders, X L; Sanderink, G C; van Ginkel, F C; van der Stelt, P F

1999-03-01

To examine the effects of exhaustion of five different processing solutions on the sensitometric properties of four dental X-ray films: Ektaspeed Plus and Ultra-speed (Kodak Eastman Co. Rochester, USA) and new and previous Dentus M2 (Agfa-Gevaert, Mortsel, Belgium). An aluminum stepwedge was used to construct characteristic curves for the four films. All films were processed manually using three sets of chemicals for manual processing: Agfa (Heraeus Kulzer, Dormagen, Germany), Kodak (Kodak-Pathé, Paris, France) and Demat (Viscopac, Athens, Greece) and two sets for automatic processing: Dürr XR and Periomat (Dürr Dental, Bietigheim-Bissingen, Germany). Film speed and gradient were evaluated until the chemicals were completely exhausted. An analysis of variance was performed separately for each set of chemicals for manual and automatic processing. Ektaspeed Plus was the fastest film in the manual processing solutions. The new Dentus M2 and Ektaspeed Plus films had similar speed using the chemicals for automatic processing. Ultra-speed had the lowest speed in all solutions, but it had the greatest consistency. Exhaustion of the developer caused a comparable decrease in speed of Ektaspeed Plus and the two Dentus M2 films. In fresh chemistry Agfa was the strongest manual processing solution, but it had the highest exhaustion rate. The Dürr XR chemical was stronger than Periomat over the whole test period. The combination of film and processing solution is an important factor for achieving constant sensitometric properties. Ektaspeed Plus and the new Dentus M2 film should be used in dental practice, as they require lower exposure and have equivalent or superior properties compared with Ultra-speed.

How treatment improvement in ADHD and cocaine dependence are related to one another: A secondary analysis.

PubMed

Levin, Frances R; Choi, C Jean; Pavlicova, Martina; Mariani, John J; Mahony, Amy; Brooks, Daniel J; Nunes, Edward V; Grabowski, John

2018-05-01

Attention-deficit hyperactivity disorder (ADHD) is overrepresented among individuals seeking treatment for substance use disorders. We previously reported that treatment with extended release mixed amphetamine salts (MAS-XR) increased abstinence, compared to placebo, among patients with co-occurring ADHD and cocaine dependence. This secondary analysis investigates the temporal relationship between ADHD improvement and cocaine abstinence in the first six weeks of the trial. The study was a three-arm, randomized, double-blinded, placebo-controlled, 14-week trial comparing MAS-XR (60 mg or 80 mg daily) versus placebo among 126 participants with ADHD and cocaine dependence. An autoregressive cross-lagged structural equation model was fit and evaluated weekly ADHD improvement (defined as ≥30% reduction in the Adult ADHD Investigator Symptom Rating Scale) and urine-confirmed abstinence over the first six weeks. The proportion of patients with each of the possible overall patterns of response was: ADHD improves before cocaine abstinence: 24%; Cocaine abstinence occurs before ADHD improvement: 12%; ADHD improvement and abstinence occur during the same week: 6%; ADHD improves but abstinence never achieved: 34%; Abstinence achieved but ADHD never improves: 6%; Neither ADHD improvement nor abstinence: 18%. A significant cross-lagged association was found; subjects with ADHD improvement at week 2 had significantly higher odds of cocaine abstinence at week 3 (p = .014). When treating co-occurring ADHD and cocaine dependence with stimulant medication, abstinence is most likely preceded by improvement in ADHD, which tends to occur early with medication treatment. Other observed temporal patterns suggest the potential complexity of the relationship between ADHD and cocaine dependence. Copyright © 2018. Published by Elsevier B.V.

Efficacy and safety of flexibly dosed brexpiprazole for the adjunctive treatment of major depressive disorder: a randomized, active-referenced, placebo-controlled study.

PubMed

Hobart, Mary; Skuban, Aleksandar; Zhang, Peter; Josiassen, Mette Krog; Hefting, Nanco; Augustine, Carole; Brewer, Claudette; Sanchez, Raymond; McQuade, Robert D

2018-04-01

To assess the efficacy, safety, and tolerability of brexpiprazole as adjunctive treatment in adults with major depressive disorder (MDD) and an inadequate response to prior antidepressant treatment (ADT). Patients with a current major depressive episode after prior treatment with 1-3 ADTs entered an 8- or 10-week prospective treatment phase in which they received double-blind placebo adjunct to open-label ADT. Inadequate responders were randomized (2:2:1) to brexpiprazole 2-3 mg/day, placebo, or quetiapine extended-release (XR) 150-300 mg/day, adjunct to the same ADT, for 6 weeks. The primary efficacy endpoint was the change from baseline (randomization) to week 6 in Montgomery-Åsberg Depression Rating Scale (MADRS) total score. The key secondary efficacy endpoint was the change in Sheehan Disability Scale (SDS) mean score. Adjunctive brexpiprazole showed a greater improvement in MADRS total score than adjunctive placebo (least squares mean difference [95% confidence interval] = -1.48 [-2.56, -0.39]; p = .0078), whereas adjunctive quetiapine XR did not separate from placebo (-0.30 [-1.63, 1.04]; p = .66). Adjunctive brexpiprazole failed to separate from placebo on the SDS mean score (-0.23 [-0.52, 0.07]; p = .13), but did improve functioning on two of the three SDS items (family life and social life). The most frequent treatment-emergent adverse events in patients receiving brexpiprazole were akathisia (6.1%), somnolence (5.6%), and headache (5.6%). Adjunctive brexpiprazole 2-3 mg/day improved symptoms of depression compared with adjunctive placebo in patients with MDD and an inadequate response to ADTs, and was well tolerated with no unexpected side effects.

Prediction of percent body fat in adult males using dual energy x-ray absorptiometry, skinfolds, and hydrostatic weighing.

PubMed

Clark, R R; Kuta, J M; Sullivan, J C

1993-04-01

The purpose of this study was to compare the prediction of percent body fat (%FAT) by dual energy x-ray absorptiometry (DXA), skinfolds (SF), and hydrostatic weighing (HW) in adult males. Subjects were 35 adult male Caucasians (mean +/- SD; age: 39.1 +/- 14.0 yr, height: 180.6 +/- 5.3 cm, weight: 81.0 +/- 11.1 kg). %FAT, determined by HW with residual volume determined via O2 dilution, served as the criterion. DXA %FAT was determined by the Norland XR-26 (XR-26) bone densitometer and by the SF equations of Jackson and Pollock (JP) (1978), and Lohman (LOH) (1981). Criterion referenced validation included analyzing mean (+/- SD) %FAT values using a one-way ANOVA for significance, comparison of mean differences (MD), correlations (r), standard error of estimates (SEE), and total errors (TE). Significant differences were found between means of each method. The r (0.91) and SEE (3.0 %FAT) for DXA compare favorably with the established SF methods of JP and LOH for predicting %FAT; however, DXA demonstrated the largest MD (3.9 %FAT) and TE (5.2 %FAT). Regression analysis yields HW = 0.79* DXA + 0.56. The results do not support earlier research that found no significant difference between HW and DXA %FAT in males. The study suggests the density of the fat-free body (DFFB) is not constant, and that the variation in bone mineral content affects the DFFB, which contributes to the differences between DXA and HW %FAT. We recommend further research to identify inconsistencies between manufacturers of DXA equipment in prediction of %FAT in males.

Evaluation of Cytochrome P450 (CYP) 3A4-Based Interactions of Levomilnacipran with Ketoconazole, Carbamazepine or Alprazolam in Healthy Subjects.

PubMed

Chen, Laishun; Boinpally, Ramesh; Gad, Nayra; Greenberg, William M; Wangsa, Julie; Periclou, Antonia; Ghahramani, Parviz

2015-10-01

Levomilnacipran is a serotonin and norepinephrine reuptake inhibitor with balanced potency for the reuptake inhibition of norepinephrine and serotonin, approved in the USA for the treatment of major depressive disorder (MDD) in adults. We conducted studies in healthy human subjects to investigate pharmacokinetic interactions when levomilnacipran extended-release (ER) is administered in combination with an inhibitor (ketoconazole), an inducer (carbamazepine), or a substrate (alprazolam) of cytochrome P450 (CYP) 3A4. Randomised, open-label studies were conducted in healthy volunteers (n = 34 ketoconazole, n = 34 carbamazepine, n = 30 alprazolam) and pharmacokinetic parameters were determined when levomilnacipran was administered alone or together with the relevant study drug. Co-administration of ketoconazole with levomilnacipran ER increased levomilnacipran maximum concentration (C max) by 39% [90% confidence interval (CI) 31-47%] and area under the concentration-time curve (AUC) by 57% (90% CI 47-67%), whereas carbamazepine reduced the C max and AUC of levomilnacipran by 26% (90% CI 22-30%) and 29% (90% CI 26-32%), respectively. Levomilnacipran at steady state had no significant effect on the pharmacokinetics of a single 1 mg dose of alprazolam extended release (XR); neither did single-dose alprazolam XR affect the steady-state pharmacokinetics of levomilnacipran. No new safety concerns were noted in these studies. Based on these results, the levomilnacipran ER dose should not exceed 80 mg once daily when used with ketoconazole, compared to 120 mg once daily in the absence of ketoconazole. No dose adjustment for levomilnacipran is suggested when levomilnacipran ER is co-administered with carbamazepine or other CYP3A4 inducers. Co-administration with levomilnacipran of drugs metabolised by CYP3A4, such as alprazolam, requires no dose adjustment due to pharmacokinetic considerations.

Orientational glasses. II. Calculation of critical thresholds in ACNxMn{1-x} mixtures

NASA Astrophysics Data System (ADS)

Galam, Serge; Depondt, Philippe

1992-10-01

Using a simple steric hindrance based idea, critical thresholds which occur in the phase diagram of ACNxMn{1-x} mixtures, where A stands for K, Na or Rb while Mn represents Br, Cl or I, are calculated. The cyanide density x is divided into a free-to-reorient part x_r, and a frozen-in part x_f. The latter term x_f is calculated from microscopic characteristics of the molecules involved. Two critical thresholds x_c and x_d for the disappearance of respectively, ferroelastic transitions and ferroelastic domains are obtained. The calculated values are in excellent agreement with available experimental results. Predictions are made for additionnal mixtures. Une idée simple d'encombrement stérique permet de calculer des seuils critiques qui apparaissent dans le diagramme de phase de mélanges ACNxMn{1-x}, où A représente K, Na ou Rb, et Mn, des atoms du type Br, Cl ou I. La concentration x du cyanure est divisée en une partie x_r de molécules libres de se réorienter, et une partie de molécules gelées x_f. Ce dernier terme x_f est calculé à partir des caractéristiques microscopiques des molécules concernées. Deux seuils critiques x_c et x_d pour la disparition respectivement des transitions et des domaines ferroelastiques sont obtenus. Les valeurs calculées sont en excellent accord avec les résultats expérimentaux disponibles. Des prédictions sont faites pour d'autres mélanges.

Adrenergic signaling mediates mechanical hyperalgesia through activation of P2X3 receptors in primary sensory neurons of rats with chronic pancreatitis.

PubMed

Wang, Shusheng; Zhu, Hong-Yan; Jin, Yi; Zhou, Youlang; Hu, Shufen; Liu, Tong; Jiang, Xinghong; Xu, Guang-Yin

2015-04-15

The mechanism of pain in chronic pancreatitis (CP) is poorly understood. The aim of this study was designed to investigate roles of norepinephrine (NE) and P2X receptor (P2XR) signaling pathway in the pathogenesis of hyperalgesia in a rat model of CP. CP was induced in male adult rats by intraductal injection of trinitrobenzene sulfonic acid (TNBS). Mechanical hyperalgesia was assessed by referred somatic behaviors to mechanical stimulation of rat abdomen. P2XR-mediated responses of pancreatic dorsal root ganglion (DRG) neurons were measured utilizing calcium imaging and whole cell patch-clamp-recording techniques. Western blot analysis and immunofluorescence were performed to examine protein expression. TNBS injection produced a significant upregulation of P2X3R expression and an increase in ATP-evoked responses of pancreatic DRG neurons. The sensitization of P2X3Rs was reversed by administration of β-adrenergic receptor antagonist propranolol. Incubation of DRG neurons with NE significantly enhanced ATP-induced intracellular calcium signals, which were abolished by propranolol, and partially blocked by protein kinase A inhibitor H-89. Interestingly, TNBS injection led to a significant elevation of NE concentration in DRGs and the pancreas, an upregulation of β2-adrenergic receptor expression in DRGs, and amplification of the NE-induced potentiation of ATP responses. Importantly, pancreatic hyperalgesia was markedly attenuated by administration of purinergic receptor antagonist suramin or A317491 or β2-adrenergic receptor antagonist butoxamine. Sensitization of P2X3Rs, which was likely mediated by adrenergic signaling in primary sensory neurons, contributes to pancreatic pain, thus identifying a potential target for treating pancreatic pain caused by inflammation. Copyright © 2015 the American Physiological Society.

Randomized controlled study of early medication change for non-improvers to antidepressant therapy in major depression--The EMC trial.

PubMed

Tadić, André; Wachtlin, Daniel; Berger, Mathias; Braus, Dieter F; van Calker, Dietrich; Dahmen, Norbert; Dreimüller, Nadine; Engel, Alice; Gorbulev, Stanislav; Helmreich, Isabella; Kaiser, Anne-Katrin; Kronfeld, Kai; Schlicht, Konrad F; Tüscher, Oliver; Wagner, Stefanie; Hiemke, Christoph; Lieb, Klaus

2016-04-01

Patients with Major Depressive Disorder (MDD) and no improvement after two weeks of antidepressant pharmacotherapy have a high risk of treatment failure. The aim of the study was to determine whether an early medication change (EMC) strategy is superior to a guideline-based treatment in MDD patients without improvement after two weeks of antidepressant pharmacotherapy. Eight-hundred-and-eighty-nine patients with MDD were enrolled, 879 patients received the SSRI escitalopram. Of those, 192 patients had no improvement, defined as a reduction of < 20% on the Hamilton Depression Rating Scale (HAMD-17) after 14 days of treatment, and were randomly assigned to open treatment with the EMC strategy (n = 97; venlafaxine XR for study days 15-56; in case of sustained non-improvement on day 28, lithium augmentation for days 29-56) or TAU (n = 95; escitalopram continuation; non-responders on day 28 were switched to venlafaxine XR for four weeks, i.e. days 29-56). The primary outcome was remission (HAMD-17 ≤ 7) after 8 weeks of treatment as assessed by blinded raters. Remission rates were 24% for EMC and 16% for TAU, which was not significantly different (p = 0.2056). Sensitivity analyses for the primary and secondary effectiveness endpoints consistently showed favorable results for patients randomized to EMC. The results confirm data from post-hoc analyses of clinical trials showing that early non-improvement identifies patients who likely need alternate interventions. However, the herein used two-step switch/augmentation strategy for this risk group was not more effective than the control intervention. Alternate strategies and other design aspects are discussed in order to support researchers addressing the same research question. Copyright © 2016 Elsevier B.V. and ECNP. All rights reserved.

COMPARISONS AMONG RADIOGRAPHY, ULTRASONOGRAPHY AND COMPUTED TOMOGRAPHY FOR EX VIVO CHARACTERIZATION OF STIFLE OSTEOARTHRITIS IN THE HORSE.

PubMed

De Lasalle, Julie; Alexander, Kate; Olive, Julien; Laverty, Sheila

2016-09-01

A better understanding of imaging characteristics of equine stifle osteoarthritis (OA) may allow earlier detection and improve prognosis. Objectives of this ex vivo, prospective, methods comparison study were to (1) describe the location and severity of naturally acquired OA lesions in the equine stifle using ultrasound (US), radiography (XR), computed tomography (CT), and macroscopic evaluation (ME); (2) compare the diagnostic performance of each imaging modality with ME; and (3) describe subchondral bone mineral density (BMD) in equine stifle joints with OA using CT. Radiographic, CT, and US evaluations were performed on 23 equine cadaver stifles and compared with ME. Significant associations were found between osteophyte global scores for all imaging modalities (CT, P ˂ 0.0001; XR, P = 0.005; US, P = 0.04) vs. ME osteophyte global scores. Osteophytes were detected most frequently in the medial femorotibial (MFT) joint. A specific pattern of osteophytes was observed, with a long ridge of new bone at the insertion of the MFT joint capsule cranially on the medial femoral condyle. A novel caudo-10°proximo-5°lateral-cranio-disto-medial oblique radiographic projection was helpful for detection of intercondylar osteophytes. Multiplanar CT reformatted images were helpful for characterizing all osteophytes. Osteophyte grades at most sites did not differ among modalities. Low sensitivity/specificity for subchondral bone sclerosis and flattening of femoral condyles suggested that these signs may not be reliable radiographic and CT indicators of equine stifle OA. Equine stifle OA was associated with a decrease in BMD and specific sites of focal subchondral bone resorption/cyst formation were found in some specimens. © 2016 American College of Veterinary Radiology.

X-chromosome gene dosage as a determinant of impaired pre and postnatal growth and adult height in Turner syndrome.

PubMed

Fiot, Elodie; Zenaty, Delphine; Boizeau, Priscilla; Haigneré, Jeremy; Dos Santos, Sophie; Léger, Juliane

2016-03-01

Short stature is a key aspect of the phenotype of patients with Turner syndrome (TS). SHOX haploinsufficiency is responsible for about two-thirds of the height deficit. The aim was to investigate the effect of X-chromosome gene dosage on anthropometric parameters at birth, spontaneous height, and adult height (AH) after growth hormone (GH) treatment. We conducted a national observational multicenter study. Birth parameter SDS for gestational age, height, and AH before and after GH treatment respectively, and height deficit with respect to target height (SDS) were classified by karyotype subgroup in a cohort of 1501 patients with TS: 45,X (36%), isoXq (19%), 45,X/46,XX (15%), XrX (7%), presence of Y (6%), or other karyotypes (17%). Birth weight, length (P<0.0001), and head circumference (P<0.001), height and height deficit with respect to target height (SDS) before GH treatment, at a median age of 8.8 (5.3-11.8) years and after adjustment for age and correction for multiple testing (P<0.0001), and AH deficit with respect to target height at a median age of 19.3 (18.0-21.8) years and with additional adjustment for dose and duration of GH treatment (P=0.006), were significantly associated with karyotype subgroup. Growth retardation tended to be more severe in patients with XrX, isoXq, and, to a lesser extent, 45,X karyotypes than in patients with 45,X/46,XX karyotypes or a Y chromosome. These data suggest that haploinsufficiency for an unknown Xp gene increases the risk of fetal and postnatal growth deficit and short AH with respect to target height after GH therapy. © 2016 European Society of Endocrinology.

A tailored mouse model of CLN2 disease: A nonsense mutant for testing personalized therapies

PubMed Central

Geraets, Ryan D.; Beraldi, Rosanna; Weimer, Jill M.; Pearce, David A.

2017-01-01

The Neuronal Ceroid Lipofuscinoses (NCLs), also known as Batten disease, result from mutations in over a dozen genes. Although, adults are susceptible, the NCLs are frequently classified as pediatric neurodegenerative diseases due to their greater pediatric prevalence. Initial clinical presentation usually consists of either seizures or retinopathy but develops to encompass both in conjunction with declining motor and cognitive function. The NCLs result in premature death due to the absence of curative therapies. Nevertheless, preclinical and clinical trials exist for various therapies. However, the genotypes of NCL animal models determine which therapeutic approaches can be assessed. Mutations of the CLN2 gene encoding a soluble lysosomal enzyme, tripeptidyl peptidase 1 (TPP1), cause late infantile NCL/CLN2 disease. The genotype of the original mouse model of CLN2 disease, Cln2-/-, excludes mutation guided therapies like antisense oligonucleotides and nonsense suppression. Therefore, the purpose of this study was to develop a model of CLN2 disease that allows for the assessment of all therapeutic approaches. Nonsense mutations in CLN2 disease are frequent, the most common being CLN2R208X. Thus, we created a mouse model that carries a mutation equivalent to the human p.R208X mutation. Molecular assessment of Cln2R207X/R207X tissues determined significant reduction in Cln2 transcript abundance and TPP1 enzyme activity. This reduction leads to the development of neurological impairment (e.g. tremors) and neuropathology (e.g. astrocytosis). Collectively, these assessments indicate that the Cln2R207X/R207X mouse is a valid CLN2 disease model which can be used for the preclinical evaluation of all therapeutic approaches including mutation guided therapies. PMID:28464005

Preliminary design study of an alternate heat source assembly for a Brayton isotope power system

NASA Technical Reports Server (NTRS)

Strumpf, H. J.

1978-01-01

Results are presented for a study of the preliminary design of an alternate heat source assembly (HSA) intended for use in the Brayton isotope power system (BIPS). The BIPS converts thermal energy emitted by a radioactive heat source into electrical energy by means of a closed Brayton cycle. A heat source heat exchanger configuration was selected and optimized. The design consists of a 10 turn helically wound Hastelloy X tube. Thermal analyses were performed for various operating conditions to ensure that post impact containment shell (PICS) temperatures remain within specified limits. These limits are essentially satisfied for all modes of operation except for the emergency cooling system for which the PICS temperatures are too high. Neon was found to be the best choice for a fill gas for auxiliary cooling system operation. Low cycle fatigue life, natural frequency, and dynamic loading requirements can be met with minor modifications to the existing HSA.

Development and characterization of PdCr temperature-compensated wire resistance strain gage

NASA Technical Reports Server (NTRS)

Lei, Jih-Fen

1989-01-01

A temperature-compensated resistance static strain gage with potential to be used to 600 C was recently developed. Gages were fabricated from specially developed palladium-13 w/o chromium (Pd-13Cr) wire and platinum (Pt) compensator. When bonded to high temperature Hastelloy X, the apparent strain from room temperature to 600 C was within 400 microstrain for gages with no preheat treatment and within 3500 microstrain for gages with 16 hours prestabilization at 640 C. The apparent strain versus temperature relationship of stabilized PdCr gages were repeatable with the reproducibility within 100 microstrain during three thermal cycles to 600 C and an 11 hours soak at 600 C. The gage fabrication, construction and installation is described. Also, the coating system used for this compensated resistance strain gage is explained. The electrical properties of the strain sensing element and main characteristics of the compensated gage including apparent strain, drift and reproducibility are discussed.

Highly textured oxypnictide superconducting thin films on metal substrates

NASA Astrophysics Data System (ADS)

Iida, Kazumasa; Kurth, Fritz; Chihara, Masashi; Sumiya, Naoki; Grinenko, Vadim; Ichinose, Ataru; Tsukada, Ichiro; Hänisch, Jens; Matias, Vladimir; Hatano, Takafumi; Holzapfel, Bernhard; Ikuta, Hiroshi

2014-10-01

Highly textured NdFeAs(O,F) thin films have been grown on ion beam assisted deposition-MgO/Y2O3/Hastelloy substrates by molecular beam epitaxy. The oxypnictide coated conductors showed a superconducting transition temperature (Tc) of 43 K with a self-field critical current density (Jc) of 7.0 × 10 4 A / cm 2 at 5 K, more than 20 times higher than powder-in-tube processed SmFeAs(O,F) wires. Albeit higher Tc as well as better crystalline quality than Co-doped BaFe2As2 coated conductors, in-field Jc of NdFeAs(O,F) was lower than that of Co-doped BaFe2As2. These results suggest that grain boundaries in oxypnictides reduce Jc significantly compared to that in Co-doped BaFe2As2 and, hence biaxial texture is necessary for high Jc.

On the Ample Service Assumption of Palm’s Theorem in Inventory Modeling.

DTIC Science & Technology

1980-10-03

c e1... . *. 0. "..M..g. -4 mooC ,00-0 $0OCO 0000000400rotN0 CO.0t0NO~ 0 000000000O00 000000a N0000000000O00 040N0N0C(C 0 M. 0. ow Sy * CP 0 *geo o ft...Sponsored Research For t Le. Library Vic e President H. F. Bright Cometanding Off!,rr. ,,SALDNRA De an Harold Liehositz New Cumberland ,rmy D put Dean...ogisics riftfiss Air For.e Ban Navy’Dept Library Rnliabilit y Anal ysis Center NAVDATA Automation Cund OP-964 Cunt "r Air Force Base APLMC/XR Naval

A Dynamic Model of an Axisymmetric, Transversely Isotropic, Fluid-Loaded, Fully Elastic Cylindrical Shell

DTIC Science & Technology

2010-01-11

and circumferential directions. These equations are fX XK £rr =—<Jrr --^-a9d ~^~axx » tr tr hx fX XV £0e =- — °’rr + — (766 —~^~axx » hr tr tx vrx ...constants in equations (1) and (2) can be solved for in terms of engineering constants. They are cll = ’ \\\\j) (1 + vrx )(1 - urx - 2vrxvxr) Erorx(l...oxr) > (14) (^ + uny(\\-u„-2urxuxr) c13 = > U->) Eruxr(\\- vrx ) c33=—« : r> (16) Vrx <\\- Vrx -2»rx»xr) and CA4=Gxr = .n E* ,- (17) 2(l + uxr

A discussion of the H-alpha filamentary nebulae and galactic structure in the Cygnus region

NASA Technical Reports Server (NTRS)

Matthews, T. A.; Simonson, S. C., III

1971-01-01

From observation of the galactic structure in Cygnus, the system of filamentary nebulae was found to lie at a distance of roughly 1.5 kpc, in the same region as about half the thermal radio sources in Cygnus X, the supernova remnant near gamma Cygni, and the association Cygnus OB2, in the direction of which the X-ray source Cygnus XR-3 is observed. The source of excitation was probably the pulse of radiation from a supernova explosion, as proposed in the case of Gum nebula. However continuing excitation by early stars in the region of Cygnus X cannot be excluded.

Characterization of Titan III-D Acoustic Pressure Spectra by Least-Squares Fit to Theoretical Model

DTIC Science & Technology

1980-01-01

P(f) for a set value of P0 and f0" Mhe inverse transform was taken and the result multiplied by a decaying exponential which modelled the envelope of...0 FORWARD TRANSFORM C IF=1 INVERSE TRANSFORM c C M 0 XREAL AND XIMAG RETURNED AS REAL AND IMAG. FOR FORWARD Xr"RM9; C M= " " " MAGNITUDE AND PHASE...34 .. .. C (PHASE IN DEGREE9) C M=2 XREAL RETURNED AS ’PSD’ XIMAG =0. C HERE ’DSD’ MEANS SUM OF N VALUES OF XREAL = MEAN SQU\\Riz OF INPUT C C FOR INVERSE

The development of pharmacokinetically enhanced amoxicillin/clavulanate for the management of respiratory tract infections in adults.

PubMed

File, Thomas M

2007-12-01

Rising levels of resistance amongst the major respiratory pathogens have compromised empiric antimicrobial therapy. This, coupled with a recent lack in availability of novel classes of antibacterials, has led to a need for new approaches to combat community respiratory tract infections. Bacteriological and clinical efficacy in two trials involving patients with acute bacterial sinusitis and six trials of patients with community-acquired pneumonia has shown that the development of a pharmacokinetically enhanced formulation of amoxicillin/clavulanate (Augmentin SR, available as Augmentin XR in the USA) has allowed amoxicillin/clavulanate to retain its place in the treatment of respiratory tract infections today.

Installation Restoration Program. Phase 2. Confirmation/Quantification. Stage 1. Air Force Plant 4, Fort Worth, Texas. Volume 5. Appendix A-2.

DTIC Science & Technology

1987-12-01

Limit Spiked Samale Samole ISailced C" auod R sIus’lt (SSR) esult. (SR) A-dded ( .SA) Iels: I. I 1. A.luminum 75-125 - I Z. Antimony - 3. Arsenic " I...UntKtarix *s %Control Limit Spiked Samale Sample SieiCm.,ound _ _R R esult (SSR) Re t,.- (SR) Added (SA) Z,10 1. AUlunu m 7 I I I 2. Antimonyj ____ 3...No. DATE Lab Sample) ;S4 No Katrix waot, " . n ...Central L imi Spiked Samale Samale Spiked Comnpound M Rsult: (SSR) Result (SR) jAdded (SA) XR

Growth of biaxially textured template layers using ion beam assisted deposition

NASA Astrophysics Data System (ADS)

Park, Seh-Jin

A two-step IBAD (ion beam assisted deposition) method is investigated, and compared to the conventional IBAD methods. The two step method uses surface energy anisotropy to achieve uniaxial texture and ion beam irradiation for biaxial texture. The biaxial texture was achieved by selective surface etching and enhanced by grain overgrowth. In this method, biaxial texture alignment is performed on a (001) uniaxially textured buffer layer. The material selected for achieving uniaxial texture, YBCO (YBa2Cu3O7-x), has strong surface energy anisotropy. YBCO is chemically susceptible to the reaction with the adjacent layer. Yttria stabilized zirconia (YSZ) was used to prevent the reaction between YBCO and the substrates (polycrystalline Ni alloy [Hastelloy] and amorphous SiNx/Si). A SrTiO3 layer was deposited on the uniaxially textured YBCO layer to retard stoichiometry change with subsequent processing. STO is well lattice matched with YBCO. A top layer of Ni was then deposited. The Ni layer was used for studying the effect of grain overgrowth. The obtained uniaxial Ni films were used for subsequent ion beam processing. Ar ion beam irradiation onto the uniaxially textured Ni film was used to study the effect of selective grain etching in achieving in-plane aligned Ni grains. Additional Ni deposition induces the overgrowth of the in-plane aligned Ni grains and, finally, the overall in-plane alignment. The in-plane alignment is examined with XRD phi scan. The effect of surface polarity of insulating oxide substrates on the epitaxial growth behavior was investigated. The lattice strain energy was the most important factor for determining the orientation of Ni films on a non-polar surface. However, for a polar surface, the surface energy plays an important role in determining the final orientation of the Ni films based on the experimental and theoretical results. Y2O3 growth behavior was also studied. The lattice strain energy is the most important factor for Y2O3 growth on single crystalline substrates. The surface energy anisotropy is the most important factor for the growth on amorphous substrates. The XRD phi scan study shows that Ar ion beam irradiation with favorable angle of incidence enhances the in-plane alignment of Y2O3 films grown on randomly oriented substrates due to the ion channeling.

Surface studies of Li-ion and Mg battery electrodes

NASA Astrophysics Data System (ADS)

Esbenshade, Jennifer

This dissertation focuses on studies of the surfaces of both Li-ion and Mg-ion battery electrodes. A fundamental understanding of processes occurring at the electrode surface is vital to the development of advanced battery systems. Additionally, modifications to the electrode surfaces are made and further characterized for improved performance. LiMn2O4 Cathodes for Li-ion Batteries: Effect of Mn in electrolyte on anode and Au coating to minimize dissolution: LiMn2O4 (LMO) is known to dissolve Mn ions with cycling. This section focuses on both the effect of the dissolution of Mn2+ into the electrolyte as well as Au coating on the LMO to improve electrochemical performance. Electrochemical quartz crystal microbalance (EQCM) was used to monitor changes in mass on the anode, SEM and AES were used to observe changes in surface morphology and chemical composition, and potentiostatic voltammetry was used to monitor charge and discharge capacity. The effect of Cu2+ addition in place of Mn2+ was also studied, as Cu is known to form an underpotential deposition (UPD) monolayer on Au electrodes. Following this, LMO particles were coated with a Au shell by a simple and scalable electroless deposition for use as Li-ion battery cathodes. The Au shell was intended to limit the capacity fade commonly seen with LMO cathodes by reducing the dissolution of Mn. Characterization by SEM, TEM, EELS, and AFM showed that the Au shell was approximately 3 nm thick. The Au shell prevented much of the Mn from dissolving in the electrolyte with 82% and 88% less dissolved Mn in the electrolyte at room temperature and 65 ºC, respectively, as compared to the uncoated LMO. Electrochemical performance studies with half cells showed that the Au shell maintained a higher discharge capacity over 400 cycles by nearly 30% with 110 mA hr g-1 for the 400th cycle as compared to a commercial LMO at 85 mA hr g-1. Similarly, the capacity fade was reduced in full cells: the coated LMO had 47% greater capacity after 400 cycles over the control. Dimensionally Controlled Lithiation of Thin Film and Multilayer Conversion Li-ion Battery Anodes: Oxide conversion reactions are an alternative approach for high capacity Li-ion batteries, but are known to suffer from structural irreversibility associated with the phase separation and reconstitution of reduced metal species and Li2O. The morphology of the reduced metal species is thought to play a critical role in the electrochemical properties of a conversion material. In this section, a model electrode is used with alternating layers of Cr and CrOx to better understand and control these phase changes in real-time and at molecular length scales. Despite lacking crystallinity at the atomic scale, this superstructure is observed (with XR) to lithiate and delithiate in a purely one-dimensional manner, preserving the layered structure. The XR data show that the metal layers act as nucleation sites for the reduction of chromium in the conversion reaction. Irreversibility during delithiation is due to the formation of a ternary phase, LiCrO2, which can be further delithiated at higher potentials. The results reveal that the combination of confining lithiation to nanoscale sheets of Li2O and the availability of reaction sites in the metal layers in the layered structure is a strategy for improving the reversibility and mass transport properties that can be used in a wide range of conversion materials. Following the Cr/CrOx study, the next step was to study intermetallics which can electrochemically alloy to Li4.4M (M = Si, Ge, Sn, etc.), providing order-of-magnitude increases in energy density. The energy density of Si may be combined with the structural reversibility of an intercalation material using a Si/metal silicide multilayer (ML). In operando XR confirms the ML's structural reversibility during Li insertion and extraction, despite an overall 3.3-fold vertical expansion. The ML electrodes also show enhanced long-term cyclability and rate capabilities relative to a comparable Si thin film electrode. This intercalation behavior found by dimensionally constraining Si lithiation promises applicability to a range of conversion reactions. Improving Electrodeposition of Mg through an Open Circuit Potential Hold: In this section, in situ XRD, XPS, SEM and electrochemical methods were used to interrogate the mechanism of Mg electrodeposition from PhMgCl/AlCl3 (APC) and EtMgCl electrolytes. An open circuit potential (OCP) pause following Mg deposition led to retained enhancement of Mg deposition and stripping kinetics along with lowered overpotentials for both. In situ XRD demonstrated that the OCP pause led to a more polycrystalline deposits relative to that without the pause, while SEM presented micrographs that showed smaller deposits with an OCP hold. The improvement is attributed to an 'enhancement layer' that formed on the electrode during the OCP hold. Analysis of XPS data suggests that this 'enhancement layer' consists of Mg and Cl retained on the electrode surface, possibly following electrode depassivation.

Freely Drifting Swallow Float Array: May 1987 Trip Report

DTIC Science & Technology

1988-05-01

co’-4 v-4~ I00 I.U I6z oJy 2ZIWO Is Y)L Figur X.4x ca C)CD U) Lo Cc r(no _0 I IC VV ~.N L) Figue X. 4bD !K U.n a1 u iP K ( o 0) 1 1(: I.,L Il 4, U ch...La. Pw ~’(rh I y- El - tD Efp KL Cr) -- - If MaIKuOOPzlwO FigreXr)b. -~ jtn x4 a(I-~)WIo u- _0 c ca CO _ -4 I’a) Fic’uX15~ 4-0C es ~ -J-L p -S.7e -f-i

X-Rays form the Vela-Puppis Complex

NASA Technical Reports Server (NTRS)

Bunner, A. N.

1971-01-01

A review of X-ray observations in the vicinity of the Gum nebula is presented. There is little doubt that the filamentary nebula Stromlo 16, the radio source Vela X, and the extended X-ray object Vel XR-2 are indications of the same, relatively nearby, supernova remnant. X-ray absorption measurements are consistent with a distance of 500 + or - 100 pc. The observed X-ray spectra have not yet distinguished between thermal bremsstrahlung and synchrotron radiation as the source mechanism. A search for low energy X-ray emission lines, both within the 5 deg diameter remnant and in the larger Gum nebula, may provide an important test for models of supernova remnant evolution.

Department of the Army Justification of Estimates for FY 1990/FY 1991 Biennial Budget Submitted to Congress January 1989. Procurement Appropriations-Construction Program

DTIC Science & Technology

1989-01-01

DATZ. An exemption to requirements of in eccnomic analysis .s :equested in icccrance with provisions AR 1,-28, Para. - 3d (3). Regulat.o references axe...provisions of XR 1I-28 Para !- 3d (3). :"gloos are required by AR 190-111, Ch. 4 and DOD 5100.76-M. Ch. 4-& 5. 12. SUPPLEMNTAL DATA: A. sti.mated Design...rdance witn AR ll-23, Para. D- 3d (2 Ths orolecm .z eu~_ - compiv .Ltn :onst=uction cr.:eria of AR0-_’:, ca. 4 and :CD 5i2 -.-. 21 4 A. Estzmated Design

Niobium-germanium superconducting tapes for high-field magnet applications

NASA Technical Reports Server (NTRS)

Braginski, A. I.; Roland, G. W.; Daniel, M. R.; Woolam, J. A.

1977-01-01

A process of fabricating superconducting Nb3Ge tapes by chemical vapor deposition (CVD) has been developed and tapes up to 10 meters long fabricated. The typical properties achieved were: critical temperature T sub c = 20 K, upper critical field H sub c2 = 29 tesla at 4.2 K, and J sub c = 3 to 4 x 10 to the 8th power A m(-2) at 4.2 K, 18 tesla. The relative depression of T sub c and H sub c2 compared with the best thin film samples sputtered on sapphire was due to the presence of Nb5Ge3 second-phase particles used as flux pinning centers and to strains induced by thermal mixmatch with Hastelloy B tape substrates. A peculiar field dependence of flux pinning force that was observed in both CVD and sputtered Nb3Ge indicated a premature pin-breaking mechanism or a phase inhomogeneity. Directions of further optimization work were defined.

Intern Summary Reports

NASA Technical Reports Server (NTRS)

2004-01-01

Topics covered include: Probe Station Antenna Range; LERCIP 2004 Summary; L.E.R.C.I.P. Internship Summary; Hubble Space Telescope Bi-Stem Thermal Shield Analyses; GRABER - the Duct Tape of Space and JIMO Heat Conducting Foam; CDF and PDF Comparison Between Humacao, Puerto Rico and Florida; Development of the On-board Aircraft Network; Development of the Planar Inlet Design and Analysis Process (PINDAP); An Overview of My 2004 Summer Internship [Non-destructive Evaluation]; My Summer Experience as an Administrative Officer Assistant [in the Safety and Assurance Directorate Office]; Programming an Experiment Control System; Reducing the Cation Exchange Capacity of Lithium Clay to Form Better Dispersed; Polymer-Clay Nanocomposites; Feasibility of EB Welded Hastelloy X and Combination of Refractory Metals; My Work in the NASA Glenn History Office and Records Management Office; Education, Technology, and Media: A Peak into My Summer Internship at NASA Glenn Research Center in Cleveland, Ohio; [The Engineering and Technical Services Directorate at the Glenn Research Center]; Drinking Water Database; Design of an EXB Probe; and Texturing Carbon-carbon Composite Radiator Surfaces Utilizing Atomic Oxygen.

Experimental verification of the Neuber relation at room and elevated temperatures. M.S. Thesis; [to predict stress-strain behavior in notched specimens of hastelloy x

NASA Technical Reports Server (NTRS)

Lucas, L. J.

1982-01-01

The accuracy of the Neuber equation at room temperature and 1,200 F as experimentally determined under cyclic load conditions with hold times. All strains were measured with an interferometric technique at both the local and remote regions of notched specimens. At room temperature, strains were obtained for the initial response at one load level and for cyclically stable conditions at four load levels. Stresses in notched members were simulated by subjecting smooth specimens to he same strains as were recorded on the notched specimen. Local stress-strain response was then predicted with excellent accuracy by subjecting a smooth specimen to limits established by the Neuber equation. Data at 1,200 F were obtained with the same experimental techniques but only in the cyclically stable conditions. The Neuber prediction at this temperature gave relatively accurate results in terms of predicting stress and strain points.

NERVA irradiation program. GTR 23, volume 1: Combined effects of reactor radiation and cryogenic temperature on NERVA structural materials

NASA Technical Reports Server (NTRS)

Mcdaniel, R. H.; Bradford, E. W.; Lewis, J. H.; Wattier, J. B.

1973-01-01

Specimens fabricated from structural materials that were candidates for certain NERVA applications were irradiated in liquid nitrogen (LN2), liquid hydrogen (LH2), water, and air. The specimens irradiated in LN2 were stored in LN2 and finally tested in LN2, or at some higher temperature in a few instances. The specimens irradiated in LH2 underwent an unplanned warmup while in storage so this portion of the test was lost; some specimens were tested in LN2 but none were tested in LH2. The Ground Test Reactor was the radiation source. The test specimens consisted mainly of tensile and fracture toughness specimens of several different materials, but other types of specimens such as tear, flexure, springs, and lubricant were also irradiated. Materials tested include Hastelloy X, Al, Ni steel, steel, Be, ZrC, Ti-6Al-4V, CuB, and Ti-5Al-2.5Sn.

Evaluating the Psychometric Properties and Responsiveness to Change of 3 Depression Measures in a Sample of Persons With Traumatic Spinal Cord Injury and Major Depressive Disorder.

PubMed

Williams, Ryan T; Heinemann, Allen W; Neumann, Holly Demark; Fann, Jesse R; Forchheimer, Martin; Richardson, Elizabeth J; Bombardier, Charles H

2016-06-01

To compare the measurement properties and responsiveness to change of the Patient Health Questionnaire-9 (PHQ-9), the Hopkins Symptom Checklist-20 (HSCL-20), and the Hamilton Depression Rating Scale (HAM-D) in people with spinal cord injury (SCI) diagnosed with major depressive disorder (MDD). Secondary analysis of depression symptoms measured at 6 occasions over 12 weeks as part of a randomized controlled trial of venlafaxine XR for MDD in persons with SCI. Outpatient and community settings. Individuals (N=133) consented and completed the drug trial. Eligibility criteria were age at least 18 years, traumatic SCI, and diagnosis of MDD. Venlafaxine XR. Patients completed the PHQ-9 and the HSCL-20 depression scales; clinical investigators completed the HAM-D and the Structured Clinical Interview for Diagnostic and Statistical Manual of Mental Disorders-Fourth Edition (DSM-IV) Dissociative Disorders, which was used as a diagnostic criterion measure. All 3 instruments were improved with rating scale analysis. The HSCL-20 and the HAM-D contained items that misfit the underlying construct and that correlated weakly with the total scores. Removing these items improved the internal consistency, with floor effects increasing slightly. The HAM-D correlated most strongly with Structured Clinical Interview for DSM-IV Dissociative Disorders diagnoses. Improvement in depression was similar on all outcome measures in both treatment and control groups. The psychometric properties of the revised depression instruments are more than adequate for routine use in adults with SCI and are responsive to clinical improvement. The PHQ-9 is the simplest instrument with measurement properties as good as or better than those of the other instruments and required the fewest modifications. Copyright © 2016 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

Short-term therapy with combination dipeptidyl peptidase-4 inhibitor saxagliptin/metformin extended release (XR) is superior to saxagliptin or metformin XR monotherapy in prediabetic women with polycystic ovary syndrome: a single-blind, randomized, pilot study.

PubMed

Elkind-Hirsch, Karen E; Paterson, Martha S; Seidemann, Ericka L; Gutowski, Hanh C

2017-01-01

To evaluate efficacy with the dipeptidyl peptidase-4 inhibitor saxagliptin (SAXA), metformin extended release (MET), and combination (SAXA-MET) in patients with polycystic ovary syndrome (PCOS) and impaired glucose regulation. Prospective, randomized, single-blind drug study. Outpatient clinic. Patients (n = 38) with PCOS (aged 18-42 years) and prediabetic hyperglycemia determined by a 75-gram oral glucose tolerance test. Patients were randomized to SAXA-MET (5 mg/2,000 mg), SAXA (5 mg), or MET (2,000 mg) for 16 weeks. Fasting and mean blood glucose, insulin sensitivity, insulin secretion, and insulin secretion-sensitivity index (IS-SI) by oral glucose tolerance tests. Free androgen index and lipid levels, average menstrual interval, and anthropometric measurements (body mass index, waist circumference, and waist/height ratio). The study was completed by 34 patients. Nineteen patients had normal glucose tolerance: 3 of 12 (25%) on MET; 6 of 11 (55%) on SAXA; and 10 of 11 (91%) on SAXA-MET (SAXA-MET statistically superior to MET) at study completion. Body mass index, waist circumference, waist/height ratio, free androgen index, insulin sensitivity, IS-SI, and menses improved in all groups; however, IS-SI and menstrual regularity were significantly better with SAXA-MET vs. MET treatment. Triglyceride, triglyceride/high-density lipoprotein cholesterol ratio and mean blood glucose significantly declined in the SAXA-MET and SAXA groups only. This pilot work provides the first evidence regarding the effects of a dipeptidyl peptidase-4 inhibitor alone and in combination with MET in this patient population. Treatment with SAXA-MET was superior to either drug alone in terms of clinical and metabolic benefits in prediabetic patients with PCOS. NCT02022007. Copyright © 2016 American Society for Reproductive Medicine. Published by Elsevier Inc. All rights reserved.

Improved NADPH supply for xylitol production by engineered Escherichia coli with glycolytic mutations.

PubMed

Chin, Jonathan W; Cirino, Patrick C

2011-01-01

Escherichia coli engineered to uptake xylose while metabolizing glucose was previously shown to produce high levels of xylitol from a mixture of glucose and xylose when expressing NADPH-dependent xylose reductase from Candida boidinii (CbXR) (Cirino et al., Biotechnol Bioeng. 2006;95:1167-1176). We then described the effects of deletions of key metabolic pathways (e.g., Embden-Meyerhof-Parnas and pentose phosphate pathway) and reactions (e.g., transhydrogenase and NADH dehydrogenase) on resting-cell xylitol yield (Y RPG: moles of xylitol produced per mole of glucose consumed) (Chin et al., Biotechnol Bioeng. 2009;102:209-220). These prior results demonstrated the importance of direct NADPH supply by NADP+-utilizing enzymes in central metabolism for driving heterologous NADPH-dependent reactions. This study describes strain modifications that improve coupling between glucose catabolism (oxidation) and xylose reduction using two fundamentally different strategies. We first examined the effects of deleting the phosphofructokinase (pfk) gene(s) on growth-uncoupled xylitol production and found that deleting both pfkA and sthA (encoding the E. coli-soluble transhydrogenase) improved the xylitol Y RPG from 3.4 ± 0.6 to 5.4 ± 0.4. The second strategy focused on coupling aerobic growth on glucose to xylitol production by deleting pgi (encoding phosphoglucose isomerase) and sthA. Impaired growth due to imbalanced NADPH metabolism (Sauer et al., J Biol Chem. 2004;279:6613-6619) was alleviated upon expressing CbXR, resulting in xylitol production similar to that of the growth-uncoupled precursor strains but with much less acetate secretion and more efficient utilization of glucose. Intracellular nicotinamide cofactor levels were also quantified, and the magnitude of the change in the NADPH/NADP+ ratio measured from cells consuming glucose in the absence vs. presence of xylose showed a strong correlation to the resulting Y RPG. Copyright © 2011 American Institute of Chemical Engineers (AIChE).

The safety and tolerability of vortioxetine: Analysis of data from randomized placebo-controlled trials and open-label extension studies

PubMed Central

Baldwin, David S; Chrones, Lambros; Florea, Ioana; Nielsen, Rebecca; Nomikos, George G; Palo, William; Reines, Elin

2016-01-01

The safety and tolerability of vortioxetine in adults with major depressive disorder was assessed. Tolerability was based on the nature, incidence and severity of treatment-emergent adverse events (TEAEs) during acute (6/8) week treatment in 11 randomized, double-blind placebo-controlled short-term studies in major depressive disorder: six with an active reference. Symptoms following discontinuation were assessed through the Discontinuation-Emergent Signs and Symptoms checklist in three studies. Long-term (⩽52 weeks) tolerability was evaluated in five open-label extension studies. Patients (n =5701) were acutely treated with either placebo (n=1817), vortioxetine (5–20mg/day; n=3018), venlafaxine XR (225mg/day; n=113) or duloxetine (60mg/day; n=753). The withdrawal rate due to TEAEs during treatment with vortioxetine (5–20mg/day) was 4.5–7.8%, compared with placebo (3.6%), venlafaxine XR (14.2%) or duloxetine (8.8%). Common TEAEs (incidence ⩾5% and >2 × placebo) with vortioxetine (5–20mg/day) were nausea (20.9–31.2%) and vomiting (2.9–6.5%). For vortioxetine (5–20mg/day), the incidence of TEAEs associated with insomnia was 2.0–5.1% versus 4.0% for placebo, and with sexual dysfunction 1.6–1.8% versus 1.0% for placebo. Discontinuation symptoms as assessed by the mean Discontinuation-Emergent Signs and Symptoms total score after abrupt discontinuation were comparable to placebo in the first and second week. Vortioxetine had no effect relative to placebo on clinical laboratory parameters, body weight, heart rate or blood pressure. Vortioxetine showed no clinically relevant effect on ECG parameters, including the QTcF interval. In long-term treatment, no new types of TEAEs were seen; the mean weight gain was 0.7–0.8kg. Thus, vortioxetine (5–20mg/day) appears safe and generally well tolerated in the treatment of major depressive disorder. PMID:26864543

The safety and tolerability of vortioxetine: Analysis of data from randomized placebo-controlled trials and open-label extension studies.

PubMed

Baldwin, David S; Chrones, Lambros; Florea, Ioana; Nielsen, Rebecca; Nomikos, George G; Palo, William; Reines, Elin

2016-03-01

The safety and tolerability of vortioxetine in adults with major depressive disorder was assessed. Tolerability was based on the nature, incidence and severity of treatment-emergent adverse events (TEAEs) during acute (6/8) week treatment in 11 randomized, double-blind placebo-controlled short-term studies in major depressive disorder: six with an active reference. Symptoms following discontinuation were assessed through the Discontinuation-Emergent Signs and Symptoms checklist in three studies. Long-term (⩽52 weeks) tolerability was evaluated in five open-label extension studies. Patients (n =5701) were acutely treated with either placebo (n=1817), vortioxetine (5-20mg/day; n=3018), venlafaxine XR (225mg/day; n=113) or duloxetine (60mg/day; n=753). The withdrawal rate due to TEAEs during treatment with vortioxetine (5-20mg/day) was 4.5-7.8%, compared with placebo (3.6%), venlafaxine XR (14.2%) or duloxetine (8.8%). Common TEAEs (incidence ⩾5% and >2 × placebo) with vortioxetine (5-20mg/day) were nausea (20.9-31.2%) and vomiting (2.9-6.5%). For vortioxetine (5-20mg/day), the incidence of TEAEs associated with insomnia was 2.0-5.1% versus 4.0% for placebo, and with sexual dysfunction 1.6-1.8% versus 1.0% for placebo. Discontinuation symptoms as assessed by the mean Discontinuation-Emergent Signs and Symptoms total score after abrupt discontinuation were comparable to placebo in the first and second week. Vortioxetine had no effect relative to placebo on clinical laboratory parameters, body weight, heart rate or blood pressure. Vortioxetine showed no clinically relevant effect on ECG parameters, including the QTcF interval. In long-term treatment, no new types of TEAEs were seen; the mean weight gain was 0.7-0.8kg. Thus, vortioxetine (5-20mg/day) appears safe and generally well tolerated in the treatment of major depressive disorder. © The Author(s) 2016.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Medina-Ramos, Jonnathan; Lee, Sang Soo; Fister, Timothy T.

Real-time changes in the composition and structure of bismuth electrodes used for catalytic conversion of CO 2 into CO were examined via X-ray absorption spectroscopy (including XANES and EXAFS), electrochemical quartz crystal microbalance (EQCM) and in situ X-ray reflectivity (XR). Measurements were performed with bismuth electrodes immersed in acetonitrile (MeCN) solutions containing a 1-butyl-3-methylimidazolium ([BMIM] +) ionic liquid promoter or electrochemically inactive tetrabutylammonium supporting electrolytes (TBAPF 6 or TBAOTf). Altogether, these measurements show that bismuth electrodes are originally a mixture of bismuth oxides (including Bi 2O 3) and metallic bismuth (Bi 0), and that the reduction of oxidized bismuth speciesmore » to Bi 0 is fully achieved under potentials at which CO 2 activation takes place. Furthermore, EQCM measurements conducted during cyclic voltammetry revealed that a bismuth-coated quartz crystal exhibits significant shifts in resistance (ΔR) prior to the onset of CO 2 reduction near -1.75 V vs. Ag/AgCl and pronounced hysteresis in frequency (Δf) and ΔR, which suggests significant changes in roughness or viscosity at the Bi/[BMIM] + solution interface. In situ XR performed on rhombohedral Bi (001) oriented films indicates extensive restructuring of the bismuth film cathodes takes place upon polarization to potentials more negative than -1.6 V vs. Ag/AgCl, which is characterized by a decrease of the Bi (001) Bragg peak intensity of ≥50% in [BMIM]OTf solutions in the presence and absence of CO 2. Over 90% of the reflectivity is recovered during the anodic half-scan, suggesting that the structural changes are mostly reversible. By contrast, such a phenomenon is not observed for thin Bi (001) oriented films in solutions of tetrabutylammonium salts that do not promote CO 2 reduction. In conclusion, these results highlight that Bi electrodes undergo significant potential-dependent chemical and structural transformations in the presence of [BMIM] + based electrolytes, including the reduction of bismuth oxide to bismuth metal, changes in roughness and near-surface viscosity.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Medina-Ramos, Jonnathan; Lee, Sang Soo; Fister, Timothy T.

Real-time changes in the composition and structure of bismuth electrodes used for catalytic conversion of CO2 into CO were examined via X-ray absorption spectroscopy (including XANES and EXAFS), electrochemical quartz crystal microbalance (EQCM), and in situ X-ray reflectivity (XR). Measurements were performed with bismuth electrodes immersed in acetonitrile (MeCN) solutions containing a 1-butyl-3-methylimidazolium ([BMIM]+) ionic liquid promoter or electrochemically inactive tetrabutylammonium supporting electrolytes (TBAPF6 and TBAOTf). Altogether, these measurements show that bismuth electrodes are originally a mixture of bismuth oxides (including Bi2O3) and metallic bismuth (Bi0) and that the reduction of oxidized bismuth species to Bi0 is fully achieved undermore » potentials at which CO2 activation takes place. Furthermore, EQCM measurements conducted during cyclic voltammetry revealed that a bismuth-coated quartz crystal exhibits significant shifts in resistance (ΔR) prior to the onset of CO2 reduction near -1.75 V vs Ag/AgCl and pronounced hysteresis in frequency (Δf) and ΔR, which suggests significant changes in roughness or viscosity at the Bi/[BMIM]+ solution interface. In situ XR performed on rhombohedral Bi (001) oriented films indicates that extensive restructuring of the bismuth film cathodes takes place upon polarization to potentials more negative than -1.6 V vs Ag/AgCl, which is characterized by a decrease of the Bi (001) Bragg peak intensity of ≥50% in [BMIM]OTf solutions in the presence and absence of CO2. Over 90% of the reflectivity is recovered during the anodic half-scan, suggesting that the structural changes are mostly reversible. In contrast, such a phenomenon is not observed for thin Bi (001) oriented films in solutions of tetrabutylammonium salts that do not promote CO2 reduction. Overall, these results highlight that Bi electrodes undergo significant potential-dependent chemical and structural transformations in the presence of [BMIM]+-based electrolytes, including the reduction of bismuth oxide to bismuth metal and changes in roughness and near-surface viscosity.« less

Endonuclease-independent LINE-1 retrotransposition at mammalian telomeres.

PubMed

Morrish, Tammy A; Garcia-Perez, José Luis; Stamato, Thomas D; Taccioli, Guillermo E; Sekiguchi, JoAnn; Moran, John V

2007-03-08

Long interspersed element-1 (LINE-1 or L1) elements are abundant, non-long-terminal-repeat (non-LTR) retrotransposons that comprise approximately 17% of human DNA. The average human genome contains approximately 80-100 retrotransposition-competent L1s (ref. 2), and they mobilize by a process that uses both the L1 endonuclease and reverse transcriptase, termed target-site primed reverse transcription. We have previously reported an efficient, endonuclease-independent L1 retrotransposition pathway (EN(i)) in certain Chinese hamster ovary (CHO) cell lines that are defective in the non-homologous end-joining (NHEJ) pathway of DNA double-strand-break repair. Here we have characterized EN(i) retrotransposition events generated in V3 CHO cells, which are deficient in DNA-dependent protein kinase catalytic subunit (DNA-PKcs) activity and have both dysfunctional telomeres and an NHEJ defect. Notably, approximately 30% of EN(i) retrotransposition events insert in an orientation-specific manner adjacent to a perfect telomere repeat (5'-TTAGGG-3'). Similar insertions were not detected among EN(i) retrotransposition events generated in controls or in XR-1 CHO cells deficient for XRCC4, an NHEJ factor that is required for DNA ligation but has no known function in telomere maintenance. Furthermore, transient expression of a dominant-negative allele of human TRF2 (also called TERF2) in XRCC4-deficient XR-1 cells, which disrupts telomere capping, enables telomere-associated EN(i) retrotransposition events. These data indicate that L1s containing a disabled endonuclease can use dysfunctional telomeres as an integration substrate. The findings highlight similarities between the mechanism of EN(i) retrotransposition and the action of telomerase, because both processes can use a 3' OH for priming reverse transcription at either internal DNA lesions or chromosome ends. Thus, we propose that EN(i) retrotransposition is an ancestral mechanism of RNA-mediated DNA repair associated with non-LTR retrotransposons that may have been used before the acquisition of an endonuclease domain.

Oxidative Stress in Mammalian Cells Impinges on the Cysteines Redox State of Human XRCC3 Protein and on Its Cellular Localization

PubMed Central

Girard, Pierre-Marie; Graindorge, Dany; Smirnova, Violetta; Rigolet, Pascal; Francesconi, Stefania; Scanlon, Susan; Sage, Evelyne

2013-01-01

In vertebrates, XRCC3 is one of the five Rad51 paralogs that plays a central role in homologous recombination (HR), a key pathway for maintaining genomic stability. While investigating the potential role of human XRCC3 (hXRCC3) in the inhibition of DNA replication induced by UVA radiation, we discovered that hXRCC3 cysteine residues are oxidized following photosensitization by UVA. Our in silico prediction of the hXRCC3 structure suggests that 6 out of 8 cysteines are potentially accessible to the solvent and therefore potentially exposed to ROS attack. By non-reducing SDS-PAGE we show that many different oxidants induce hXRCC3 oxidation that is monitored in Chinese hamster ovarian (CHO) cells by increased electrophoretic mobility of the protein and in human cells by a slight decrease of its immunodetection. In both cell types, hXRCC3 oxidation was reversed in few minutes by cellular reducing systems. Depletion of intracellular glutathione prevents hXRCC3 oxidation only after UVA exposure though depending on the type of photosensitizer. In addition, we show that hXRCC3 expressed in CHO cells localizes both in the cytoplasm and in the nucleus. Mutating all hXRCC3 cysteines to serines (XR3/S protein) does not affect the subcellular localization of the protein even after exposure to camptothecin (CPT), which typically induces DNA damages that require HR to be repaired. However, cells expressing mutated XR3/S protein are sensitive to CPT, thus highlighting a defect of the mutant protein in HR. In marked contrast to CPT treatment, oxidative stress induces relocalization at the chromatin fraction of both wild-type and mutated protein, even though survival is not affected. Collectively, our results demonstrate that the DNA repair protein hXRCC3 is a target of ROS induced by environmental factors and raise the possibility that the redox environment might participate in regulating the HR pathway. PMID:24116071

The Analysis of Pendolino (peo) Mutants Reveals Differences in the Fusigenic Potential among Drosophila Telomeres

PubMed Central

Marzullo, Marta; Raffa, Grazia D.; Morciano, Patrizia; Raimondo, Domenico; Burla, Romina; Saggio, Isabella; Gatti, Maurizio

2015-01-01

Drosophila telomeres are sequence-independent structures that are maintained by transposition to chromosome ends of three specialized retroelements (HeT-A, TART and TAHRE; collectively designated as HTT) rather than telomerase activity. Fly telomeres are protected by the terminin complex (HOAP-HipHop-Moi-Ver) that localizes and functions exclusively at telomeres and by non-terminin proteins that do not serve telomere-specific functions. Although all Drosophila telomeres terminate with HTT arrays and are capped by terminin, they differ in the type of subtelomeric chromatin; the Y, XR, and 4L HTT are juxtaposed to constitutive heterochromatin, while the XL, 2L, 2R, 3L and 3R HTT are linked to the TAS repetitive sequences; the 4R HTT is associated with a chromatin that has features common to both euchromatin and heterochromatin. Here we show that mutations in pendolino (peo) cause telomeric fusions (TFs). The analysis of several peo mutant combinations showed that these TFs preferentially involve the Y, XR and 4th chromosome telomeres, a TF pattern never observed in the other 10 telomere-capping mutants so far characterized. peo encodes a non-terminin protein homologous to the E2 variant ubiquitin-conjugating enzymes. The Peo protein directly interacts with the terminin components, but peo mutations do not affect telomeric localization of HOAP, Moi, Ver and HP1a, suggesting that the peo-dependent telomere fusion phenotype is not due to loss of terminin from chromosome ends. peo mutants are also defective in DNA replication and PCNA recruitment. However, our results suggest that general defects in DNA replication are unable to induce TFs in Drosophila cells. We thus hypothesize that DNA replication in Peo-depleted cells results in specific fusigenic lesions concentrated in heterochromatin-associated telomeres. Alternatively, it is possible that Peo plays a dual function being independently required for DNA replication and telomere capping. PMID:26110638

Experimental study on impact-induced seismic wave propagation through granular materials

NASA Astrophysics Data System (ADS)

Yasui, Minami; Matsumoto, Eri; Arakawa, Masahiko

2015-11-01

Impact-induced seismic waves are supposed to cause movements of regolith particles, resulting in modifications of asteroidal surfaces. The imparted seismic energy is thus a key parameter to determining the scale and magnitude of this seismic shaking process. It is important to study the propagation velocity, attenuation rate, and vibration period of the impact-induced seismic wave to estimate the seismic energy. Hence, we conducted impact cratering experiments at Kobe University using a 200-μm glass beads target to simulate a regolith layer, and measured the impact-induced seismic wave using three accelerometers set on the target surface at differences ranging from 3.2 to 12.7 cm. The target was impacted with three kinds of projectiles at ∼100 m s-1 using a one-stage gas gun. The propagation velocity of the seismic wave in the beads target was 108.9 m s-1, and the maximum acceleration, gmax, in the unit of m s-2, measured by each accelerometer showed good correlation with the distance from the impact point normalized by the crater radius, x/R, irrespective of projectile type. They also were fitted by one power-law equation, gmax = 102.19 (x/R)-2.21. The half period of the first peak of the measured seismic waves was ∼0.72 ms, and this duration was almost consistent with the penetration time of each projectile into the target. According to these measurements, we estimated the impact seismic efficiency factor, that is, the ratio of seismic energy to kinetic energy of the projectile, to be almost constant, 5.7 × 10-4 inside the crater rim, while it exponentially decreased with distance from the impact point outside the crater rim. At a distance quadruple of the crater radius, the efficiency factors were 4.4 × 10-5 for polycarbonate projectile and 9.5 × 10-5 for alumina and stainless steel projectiles.

Comparison of drug utilization patterns in observational data: antiepileptic drugs in pediatric patients

PubMed Central

Bourgeois, Florence T; Olson, Karen L; Poduri, Annapurna; Mandl, Kenneth D

2015-01-01

Purpose Physicians require information on the comparative benefits and harms of medications for optimal treatment decisions. However, this type of data is limited, especially for pediatric patients. Objective Our aim was to use observational data to measure and compare medication utilization patterns in a pediatric patient population. Methods Using pharmacy claims data from a large, national-scale insurance program in the US, we identified all patients with a diagnosis of epilepsy treated with a first-generation (carabamazepine, ethosuximide, phenobarbital, phenytoin, valproate) or second-generation (carbamazepine XR, gabapentin, lamotrigine, levetiracetam, oxcarbazepine, tiagabine, topiramate, valproate XR, zonisamide) antiepileptic drug. Treatment periods were defined based on prescription fill dates and medication days supplied. Medication use was measured for individual antiepileptic drugs and for first-generation and second-generation drugs as groups. Results There were 2527 (54%) patients who initiated therapy with first-generation and 2139 (46%) with second-generation antiepileptics. First- and second-generation drugs had the same one-year retention rates (26% [95%CI 24–28] and 26% [95%CI 25–28], respectively). A total of 26% (95%CI 25–28) and 29% (95%CI 27–31) of patients who started on a first- or second-generation antiepileptic medication, respectively, resumed treatment with the initial drug after discontinuation. Overall, 73% (95%CI 71–74) of patients were treated with only one antiepileptic drug, with similar rates for patients started on first- and second-generation drugs (71% [95%CI 69–73] vs 74% [95%CI 72–76]). Conclusions Comparing drug utilization patterns in a pediatric population using observational data, we found similar rates of retention and therapeutic changes. These findings are consistent with available comparative data and demonstrate an approach that could be extended to other drug classes and conditions in pediatric populations to examine drug effectiveness. PMID:26070280

Comparison of Drug Utilization Patterns in Observational Data: Antiepileptic Drugs in Pediatric Patients.

PubMed

Bourgeois, Florence T; Olson, Karen L; Poduri, Annapurna; Mandl, Kenneth D

2015-10-01

Physicians require information on the comparative benefits and harms of medications for optimal treatment decisions. However, this type of data is limited, especially for pediatric patients. Our aim was to use observational data to measure and compare medication utilization patterns in a pediatric patient population. Using pharmacy claims data from a large, national-scale insurance program in the USA, we identified all patients with a diagnosis of epilepsy treated with a first-generation antiepileptic drug (carbamazepine, ethosuximide, phenobarbital, phenytoin, or valproate) or a second-generation antiepileptic drug [carbamazepine extended release (XR), gabapentin, lamotrigine, levetiracetam, oxcarbazepine, tiagabine, topiramate, valproate XR, or zonisamide]. Treatment periods were defined on the basis of prescription fill dates and medication days supplied. Medication use was measured for individual antiepileptic drugs and for first-generation and second-generation drugs as groups. There were 2527 patients (54 %) who initiated therapy with first-generation antiepileptics and 2139 patients (46 %) who initiated therapy with second-generation antiepileptics. First- and second-generation drugs had the same 1-year retention rates [26 % (95 % confidence interval (CI) 24-28) and 26 % (95 % CI 25-28), respectively], and 26 % of patients (95 % CI 25-28) and 29 % of patients (95 % CI 27-31) who started on a first- or second-generation antiepileptic medication, respectively, resumed treatment with the initial drug after discontinuation. Overall, 73 % of patients (95 % CI 71-74) were treated with only one antiepileptic drug, with similar rates for patients started on first- and second-generation drugs [71 % (95 % CI 69-73) versus 74 % (95 % CI 72-76)]. Comparing drug utilization patterns in a pediatric population using observational data, we found similar rates of retention and therapeutic changes. These findings are consistent with the available comparative data and demonstrate an approach that could be extended to other drug classes and conditions in pediatric populations to examine drug effectiveness.

Validity and Reliability of Spine Rasterstereography in Patients With Adolescent Idiopathic Scoliosis.

PubMed

Tabard-Fougère, Anne; Bonnefoy-Mazure, Alice; Hanquinet, Sylviane; Lascombes, Pierre; Armand, Stéphane; Dayer, Romain

2017-01-15

Test-retest study. This study aimed to evaluate the validity and reliability of rasterstereography in patients with adolescent idiopathic scoliosis (AIS) with a major curve Cobb angle (CA) between 10° and 40° for frontal, sagittal, and transverse parameters. Previous studies evaluating the validity and reliability of rasterstereography concluded that this technique had good accuracy compared with radiographs and a high intra- and interday reliability in healthy volunteers. To the best of our knowledge, the validity and reliability have not been assessed in AIS patients. Thirty-five adolescents with AIS (male = 13) aged 13.1 ± 2.0 years were included. To evaluate the validity of the scoliosis angle (SA) provided by rasterstereography, a comparison (t test, Pearson correlation) was performed with the CA obtained using 2D EOS® radiography (XR). Three rasterstereographic repeated measurements were independently performed by two operators on the same day (interrater reliability) and again by the first operator 1 week later (intrarater reliability). The variables of interest were the SA, lumbar lordosis, and thoracic kyphosis angle, trunk length, pelvic obliquity, and maximum, root mean square and amplitude of vertebral rotations. The data analyses used intraclass correlation coefficients (ICCs). The CA and SA were strongly correlated (R = 0.70) and were nonsignificantly different (P = 0.60). The intrarater reliability (same day: ICC [1, 1], n = 35; 1 week later: ICC [1, 3], n = 28) and interrater reliability (ICC [3, 3], n = 16) were globally excellent (ICC > 0.75) except for the assessment of pelvic obliquity. This study showed that the rasterstereographic system allows for the evaluation of AIS patients with a good validity compared with XR with an overall excellent intra- and interrater reliability. Based on these results, this automatic, fast, and noninvasive system can be used for monitoring the evolution of AIS in growing patients instead of repetitive radiographs, thereby reducing radiation exposure and decreasing costs. 4.

LncRNAs expression in adjuvant-induced arthritis rats reveals the potential role of LncRNAs contributing to rheumatoid arthritis pathogenesis.

PubMed

Jiang, Hui; Qin, Xiu-Juan; Li, Wei-Ping; Ma, Rong; Wang, Ting; Li, Zhu-Qing

2016-11-15

Long non-coding RNAs (LncRNAs) are an important class of widespread molecules involved in diverse biological functions, which are exceptionally expressed in numerous types of diseases. Currently, limited study on LncRNA in rheumatoid arthritis (RA) is available. In this study, we aimed to identify the specifically expressed LncRNA that are relevant to adjuvant-induced arthritis (AA) in rats, and to explore the possible molecular mechanisms of RA pathogenesis. To identify LncRNAs specifically expressed in rheumatoid arthritis, the expression of LncRNAs in synoviums of rats from the model group (n=3) was compared with that in the control group (n=3) using Arraystar Rat LncRNA/mRNA microarray and real-time polymerase chain reaction (RT-PCR). Up to 260 LncRNAs were found to be differentially expressed (≥1.5-fold-change) in the synoviums between AA model and the normal rats (170 up-regulated and 90 down-regulated LncRNAs in AA rats compared with normal rats). Coding-non-coding gene co-expression networks (CNC network) were drawn based on the correlation analysis between the differentially expressed LncRNAs and mRNAs. Six LncRNAs, XR_008357, U75927, MRAK046251, XR_006457, DQ266363 and MRAK003448, were selected to analyze the relationship between LncRNAs and RA via the CNC network and GO analysis. Real-time PCR result confirmed that the six LncRNAs were specifically expressed in the AA rats. These results revealed that clusters of LncRNAs were uniquely expressed in AA rats compared with controls, which manifests that these differentially expressed LncRNAs in AA rats might play a vital role in RA development. Up-regulation or down-regulation of the six LncRNAs might contribute to the molecular mechanism underlying RA. To sum up, our study provides potential targets for treatment of RA and novel profound understanding of the pathogenesis of RA. Copyright © 2016. Published by Elsevier B.V.

Current status and future prospects of Japanese national project on coated conductor development and its applications

NASA Astrophysics Data System (ADS)

Shiohara, Y.; Yoshizumi, M.; Izumi, T.; Yamada, Y.

2008-09-01

Four years of the current five-year national project since 2003 for development of coated conductors using Y-system superconductors have passed and lots of remarkable results have been achieved. In this paper, the current status and the future prospect of this project are reviewed. The current national project comprises several groups of national laboratories, universities and private companies. The group of high performance tape development, consisting of Fujikura and SRL-NCCC, has worked on the tape by PLD-REBCO superconducting tapes on the PLD-CeO 2/IBAD-GZO buffered substrates. The high product of Ic and L equal to 112,166 A m was achieved in the 368 m-304.8 A GdBCO tape whose Ic value is mostly above 350 A/cm-w. The performance under the magnetic fields was also improved up to 42 A at 3 T in a GdBCO short film with doping of ZrO 2. About 61 m long GdBCO tape with ZrO 2 doping showed a high Ic value of 220 A at self field and 30 A at 3 T. On the other hand, the other group focusing on the low production cost has worked on processes of TFA-MOD and MOCVD, etc. The extremely high Ic value of 735 A/cm-w was attained in the TFA-MOD films on PLD-CeO 2/IBAD-GZO/Hastelloy C276 substrate by means of using the effect of Ba-poor nominal composition. In the efforts for long tape production, 200 m long tapes with high Ic values of 200 A/cm-w and 205 A/cm-w were obtained by MOD-YBCO/PLD-CeO 2/IBAD-GZO/Hastelloy C276 and PLD-HoBCO on buffered NiW substrate, respectively. The Ic × L value of the MOD-derived tape was 40,000 A m, which is the highest value in the world by the MOD process. Based on the above achievements on the coated conductor process development, two new additional goals were set in the project. One is the development for the extremely low cost tape and another is the development of the basic technologies for making the electric power devices including cables, transformers, motors, current-limiters and cryocoolers. Some of the new themes already revealed the marvellous results such as 15 kW motor, low AC loss coils, low AC loss cables, etc.

All Prime Contract Awards by State or Country, Place, and Contractor. Part 18 (Elmo Texas-San Saba Texas)

DTIC Science & Technology

1990-01-01

01D I0 WN 00 40C4 00 00 0 2 -i iniin moon 1-1 in0 0 0 -~i of 1-4 It1.0. 9- ) 0 r- 0L U. td ) U- 0- z r- ɘ C C 0 Qt I 10- 0 < xr4I NN 00) N j C" 000...p- co. 0-4 itBOOC 0. 40 aOO B-OO OOO Z B-B-B 00 C> W-4 B-B COB0-4 3H. 0 ) I.-0 UB U 000)-4 WO04L000000000 20 WOO P- C in fa 00-4 BBD ~ ~0 ccCe 00 00

A Training Feedback System for Brigade Command Groups

DTIC Science & Technology

1978-06-01

n >U ~4) 4-- NL 4-o 0 L H vc 0 ( a wE -a 00CO 4 i0 a) cab 0 O0N 41-1-N r-4 N 4- 0o 24AN 1.N *r4-4 4-1 4-IN -’H COr i H -~ d - H- 1()e4J El4 r--4 w U...4 P $ ~4 ) El4 ) Q) 1) In 4) *Cd a. "C "oH I H el ( c. 0 -H4 Xr C 1OO0 𔃺 4-J co ro41-’H 0- 13 . 0Cd 41>ý4J r--H Ca Co r 4.4 HCdCJ 0 >" a) C-. 0 0000

Highly-branched anisotropic hybrid nanoparticles at surfaces.

NASA Astrophysics Data System (ADS)

Tsukruk, Vladimir

2009-03-01

We present a brief overview of our recent studies on combined hybrid anisotropic structures composed of inorganic nanoparticles and highly branched molecules such as modified silsesquioxanes polyhedra cores (POSS) with mixed hydrophobic-hydrophilic tails and silver nanowires with functionalized star block copolymer with embedded gold nanoparticles (nanocobs). We demonstrate two-stage melting of that branched POSS and their ability to form monolayer and multilayered LB structures. On the other hand, we observed that silver-BCP-gold nanocobs display extremely bright Raman scattering caused by surface enhanced Raman effect with very different longitudinal and transversal optical properties as revealed by high-resolution confocal Raman microscopy. To study these hybrid nanostructures we applied combined AFM, SEM, TEM, XPS, SERS, UV-vis, and XR techniques.

Alloy substantially free of dendrites and method of forming the same

DOE Office of Scientific and Technical Information (OSTI.GOV)

de Figueredo, Anacleto M.; Apelian, Diran; Findon, Matt M.

2009-04-07

Described herein are alloys substantially free of dendrites. A method includes forming an alloy substantially free of dendrites. A superheated alloy is cooled to form a nucleated alloy. The temperature of the nucleated alloy is controlled to prevent the nuclei from melting. The nucleated alloy is mixed to distribute the nuclei throughout the alloy. The nucleated alloy is cooled with nuclei distributed throughout.

Development of a Brazing Alloy for the Mechanically Alloyed High Temperature Sheet Material INCOLOY Alloy MA 956.

DTIC Science & Technology

1981-09-01

OF A BRAZING ALLOY FOR THE MECHANICALLY ALLOYED HIGH TEMPERATURE SHEET MATERIAL INCOLOY ALLOY MA 956 W. E. Morgan and Dr. P. J. Bridges N. Wiggin...PERIOD COVERED DEVELOPMENT OF A BRAZING ALLOY FOR THE Final Report MECHANICALLY ALLOYED HIGH TEMPERATURE Dec 1978 - March 1981 SHEET MATERIAL INCOLOY...block nomber) High temperature ODS alloys, Braze development, Braze alloys, INCOLOY MA 956, Ni-Cr-Pd, Fe-Cr-Pd, Ni-Cr-Ge, Fe-Cr-Ge, Fe-Cr-B, Fe-Cr-Si

Preliminary Material Properties Handbook, English Units

DTIC Science & Technology

1999-12-01

References 5-17 Chapter 6. Heat-Resistant Alloys 6.1 General 6-1 6.2 Iron- Chromium -Nickel-Base Alloys 6-3 6.3 Nickel-Base Alloys 6-3 6.4...elements as vanadium, molybdenum, iron, or chromium . In addition to strengthening of titanium by the alloying additions, alpha-beta alloys may be...alloys are arbitrarily defined as iron alloys richer in alloy content than the 18 percent chromium , 8 percent nickel types, or as alloys with a base

Thermodynamics of Alloys: Studies of Nickel-Gallium, Nickel-Germanium and Nickel-Rhodium Alloys.

DTIC Science & Technology

NICKEL ALLOYS, *GALLIUM ALLOYS, *GERMANIUM ALLOYS, * RHODIUM ALLOYS, *PHASE STUDIES, THERMODYNAMICS, INTERMETALLIC COMPOUNDS, FREE ENERGY, ENTROPY, HEAT OF FORMATION, CRYSTAL STRUCTURE, UNITED KINGDOM.

Corrosion behaviour of Al-Fe-Ti-V medium entropy alloy

NASA Astrophysics Data System (ADS)

Bodunrin, M. O.; Obadele, B. A.; Chown, L. H.; Olubambi, P. A.

2017-12-01

Alloys containing up to four multi-principal elements in equiatomic ratios are referred to as medium entropy alloys (MEA). These alloys have attracted the interest of many researchers due to the superior mechanical properties it offers over the traditional alloys. The design approach of MEA often results to simple solid solution with either body centered cubic; face centered cubic structures or both. As the consideration for introducing the alloys into several engineering application increases, there have been efforts to study the corrosion behaviour of these alloys. Previous reports have shown that some of these alloys are more susceptible to corrosion when compared with traditional alloys due to lack of protective passive film. In this research, we have developed AlFeTiV medium entropy alloys containing two elements (Ti and Al) that readily passivate when exposed to corrosive solutions. The alloys were produced in vacuum arc furnace purged with high purity argon. Open circuit potential and potentiodynamic polarisation tests were used to evaluate the corrosion behaviour of the as-cast AlFeTiV alloy in 3.5 wt% NaCl and 1 M H2SO4. The corrosion performance of the alloy was compared with Ti-6Al-4V alloy tested under similar conditions. The results show that unlike in Ti-6Al-4V alloy, the open circuit potential of the AlFeTiV alloy move towards the negative values in both 3.5 wt% NaCl and 1 M H2SO4 solutions indicating that self-activation occurred rapidly on immersion. Anodic polarisation of the alloys showed that AlFeTiV alloy exhibited a narrow range of passivity in both solutions. In addition, the alloys exhibited lower Ecorr and higher Icorr when compared with traditional Ti-6Al-4V alloy. The traditional Ti-6Al-4V alloy showed superior corrosion resistant to the AlFeTiV alloy in both 3.5 wt.% NaCl and 1 M H2SO4 solutions.

Production of intergranular attack of alloy 600, alloy 690, and alloy 800 tubing in tubesheet crevices: Topical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott, D.B.; Glaves, C.L.,

1987-07-01

Three model boilers, manufactured to simulate full-size tube sheet crevices, were tested with various secondary side environments. The first was faulted with organics representative of the decomposition of humic acid. The second was faulted with sodium carbonate and sodium hydroxide, while the third was faulted with sodium sulfate and sodium hydroxide. Each model contained seven tubes, which included Alloy 600 in the mill-annealed (MA) and thermally-treated (TT) conditions and Alloy 690 in the thermally-treated condition. Two models contained Alloy 800 tubes in the mill-annealed condition and one had Alloy 800 in the mill-annealed/cold-worked/glass-bead-peened condition. Two different sizes of tubesheet crevicesmore » were used in all model boilers. In the organics-faulted boiler, tubes of Alloy 600MA, Alloy 690TT and Alloy 800MA experienced no significant intergranular attack (IGA); however, the Alloy 600TT had intergranular attack (IGA) three to four grains deep. The carbonate-caustic faulted boiler experienced throughwall stress corrosion cracking (SCC) in all tubes of Alloy 600 MA and Alloy 800 MA. Eddy current indications were present in Alloy 690TT, Alloy 600TT and Alloy 800 in the mill-annealed/cold worked/glass-bead-peened condition. Metallographic examination of tubes from the third model boiler, faulted with sodium sulfate and caustic, revealed IGA in the mill-annealed Alloy 600 tubes. The IGA was more extensive in an Alloy 600 tube annealed at 1700/sup 0/F than an Alloy 600 tube annealed at 1875/sup 0/F.« less

Preliminary Material Properties Handbook, SI Units

DTIC Science & Technology

1999-12-01

5.5 Beta, Near-Beta, and Metastable Titanium Alloys 5-11 References 5-17 Chapter 6. Heat-Resistant Alloys 6.1 General 6-1 6.2 Iron- Chromium ...elements as vanadium, molybdenum, iron, or chromium . In addition to strengthening of titanium by the alloying additions, alpha-beta alloys may be...ALLOYS Heat-resistant alloys are arbitrarily defined as iron alloys richer in alloy content than the 18 percent chromium , 8 percent nickel types

Preliminary Material Properties Handbook. Volume 2: SI Units

DTIC Science & Technology

2000-07-01

6-1 6.2 Iron- Chromium -Nickel-Base Alloys...iron, or chromium . In addition to strengthening of titanium by the alloying additions, alpha-beta alloys may be further strengthened by heat...6.3.3 6.3.4 6.3.5 6.4 6.5 6.5.1 Iron- Chromium -Nickel-Base Alloys Nickel-Base Alloys AEREX® 350 alloy HAYNES® 230® alloy HAYNES® HR-120® alloy Inconel

The Frequency Response and Operating Characteristics of the XR-3 Loads and Motions Program

DTIC Science & Technology

1976-06-01

TD -t- M - \\ \\ t:5Tt \\ ’X ^pl 1 \\ \\\\ 1 1 1 r ^ ’ 1 ^ ;f<i^^ ’ 1:^’ ’ 1 ’ 1 \\ J ) i ! r ;i 1 MM III I’MrMr^m 1 1 ’ 1 111’ 1 : ; 11 I ! i ; ! i...Operating Characteristics V=30 kts, A=0.3 ft, Ahead Seas 92 + 1 i h +- .... ^ _|_ „ . . , 1 , . . . , .,_ . , 1 J _lJ 1 i I .. ._ ., . td ii ! ! 1 1 1 T 1...rrPP I 1 1 i-j-K -w III -r-f-j-^- 1 1 i 1 --i*i- -r-HJ-U+f u**—^—^ .^ -« td ^:ii:=niri;: -^ H-r— -j-O* *- " LjS : ; 1 h i ! ’ 1 ’ i 1 ^ AJ —

SAR (Synthetic Aperture Radar) Data Collection and Processing Summary - 1984 SARSEX (SAR Internal Wave Signature Experiment) Experiment.

DTIC Science & Technology

1985-03-01

DIVISION ;! -0 N xr-0 n 0n4 1 1 I- C) 0 Ic 0 C WIx W Qr - - r -r 01............................. I Cq I1 -a I- I X 0’ an w I w kI~r 1 0r- r- r . 0~~~ Cs CW 1...object from the SAR platform . Ground range, the 102 ~RIM RADAR DIVISION 0 0 sc 0’. C4 C4 Xn en % >4-4 441i V-u -- - W 1-11 04 v4 0o 0 4 0 (A~U Go 4J...Rg = rRF -hy ,(3) for the flat earth or low-altitude case, where h is the platform altitude. Because the range and azimuth scales are not the same

Early onset of action and sleep-improving effect are crucial in decreasing suicide risk: the role of quetiapine XR in the treatment of unipolar and bipolar depression.

PubMed

Pompili, Maurizio; Rihmer, Zoltan; Gonda, Xenia; Serafini, Gianluca; Sher, Leo; Girardi, Paolo

2012-01-01

Although the possibilities of antidepressive pharmacotherapy are continuously improving, the rate of nonresponders or partial responders is still relatively high. Suicidal behavior, the most tragic consequence of untreated or unsuccessfully treated depression, commonly observed in the first few weeks of antidepressive treatment before the onset of therapeutic action, is strongly related to certain symptoms of depression like insomnia. The present paper reviews the newly discovered and well-documented antidepressive effect of quetiapine in bipolar and unipolar depression with special focus on its early onset of action and its sleep-improving effects. Both beneficial effects play an important role in the reduction of suicidal risk frequently observed in depressed patients.

Method of producing superplastic alloys and superplastic alloys produced by the method

NASA Technical Reports Server (NTRS)

Troeger, Lillianne P. (Inventor); Starke, Jr., Edgar A. (Inventor); Crooks, Roy (Inventor)

2002-01-01

A method for producing new superplastic alloys by inducing in an alloy the formation of precipitates having a sufficient size and homogeneous distribution that a sufficiently refined grain structure to produce superplasticity is obtained after subsequent PSN processing. An age-hardenable alloy having at least one dispersoid phase is selected for processing. The alloy is solution heat-treated and cooled to form a supersaturated solid solution. The alloy is plastically deformed sufficiently to form a high-energy defect structure useful for the subsequent heterogeneous nucleation of precipitates. The alloy is then aged, preferably by a multi-stage low and high temperature process, and precipitates are formed at the defect sites. The alloy then is subjected to a PSN process comprising plastically deforming the alloy to provide sufficient strain energy in the alloy to ensure recrystallization, and statically recrystallizing the alloy. A grain structure exhibiting new, fine, equiaxed and uniform grains is produced in the alloy. An exemplary 6xxx alloy of the type capable of being produced by the present invention, and which is useful for aerospace, automotive and other applications, is disclosed and claimed. The process is also suitable for processing any age-hardenable aluminum or other alloy.

Effect of microstructure on stress corrosion cracking of alloy 600 and alloy 690 in 40% NaOH

NASA Astrophysics Data System (ADS)

Kim, H. P.; Hwang, S. S.; Lim, Y. S.; Kuk, I. H.; Kim, J. S.

2001-02-01

Stress corrosion cracking (SCC) behaviors of Alloy 600, Alloy 690 and the Ni-10Cr-10Fe alloy have been studied using a C-ring in 40% NaOH solution at 315°C. The current density of Alloy 690 in polarization curves was higher at 200 mV above corrosion potential than that of Alloy 600. SCC resistance increased with Cr content for the chromium carbide free alloys, probably due to facilitation of SCC crack tip blunting with an increase in Cr content. Both thermally treated Alloy 600 and sensitized Alloy 600 have a comparable amount of intergranular carbide. But the former is more resistant to SCC than the latter, which might be attributed to the presence of the slight Cr depletion around the grain boundary in the former one. Sensitized Alloy 600 showed higher SCC resistance than the solution annealed one due to intergranular carbide in sensitized Alloy 600. This implies that the beneficial effect of intergranular carbide overrides the harmful effects of Cr depletion for sensitized Alloy 600. SCC resistance of Alloy 600 increased with grain size.

Properties and microstructures for dual alloy combinations of three superalloys with alloy 901

NASA Technical Reports Server (NTRS)

Harf, F. H.

1985-01-01

Dual alloy combinations have potential for use in aircraft engine components such as turbine disks where a wide range of stress and temperature regimes exists during operation. Such alloy combinations may directly result in the conservation of elements which are costly or not available domestically. Preferably, a uniform heat treatment yielding good properties for both alloys should be used. Dual alloy combinations of iron rich Alloy 901 with nickel base superalloys Rene 95, Astroloy, or MERL 76 were not isostatically pressed from prealloyed powders. Individual alloys, alloy mixtures, and layered alloy combinations were given the heat treatments specified for their use in turbine disks or appropriate for Alloy 901. Selected specimens were overaged for 1500 hr at 650 C. Metallographic examinations revealed the absence of phases not originally present in either alloy of a combination. Mechanical tests showed adequate properties in combinations of Rene 95 or Astroloy with Alloy 901 when given the Alloy 901 heat treatment. Combinations with MERL 76 had better properties when given the MERL 76 heat treatment. The results indicate that these combinations are promising candidates for use in turbine disks.

Surface modification of high temperature iron alloys

DOEpatents

Park, Jong-Hee

1995-01-01

A method and article of manufacture of a coated iron based alloy. The method includes providing an iron based alloy substrate, depositing a silicon containing layer on the alloy surface while maintaining the alloy at a temperature of about 700.degree. C.-1200.degree. C. to diffuse silicon into the alloy surface and exposing the alloy surface to an ammonia atmosphere to form a silicon/oxygen/nitrogen containing protective layer on the iron based alloy.

Surface modification of high temperature iron alloys

DOEpatents

Park, J.H.

1995-06-06

A method and article of manufacture of a coated iron based alloy are disclosed. The method includes providing an iron based alloy substrate, depositing a silicon containing layer on the alloy surface while maintaining the alloy at a temperature of about 700--1200 C to diffuse silicon into the alloy surface and exposing the alloy surface to an ammonia atmosphere to form a silicon/oxygen/nitrogen containing protective layer on the iron based alloy. 13 figs.

Analysis of thermoelectric properties of high-temperature complex alloys of nickel-base, iron-base and cobalt-base groups

NASA Technical Reports Server (NTRS)

Holanda, R.

1984-01-01

The thermoelectric properties alloys of the nickel-base, iron-base, and cobalt-base groups containing from 1% to 25% 106 chromium were compared and correlated with the following material characteristics: atomic percent of the principle alloy constituent; ratio of concentration of two constituents; alloy physical property (electrical resistivity); alloy phase structure (percent precipitate or percent hardener content); alloy electronic structure (electron concentration). For solid-solution-type alloys the most consistent correlation was obtained with electron concentration, for precipitation-hardenable alloys of the nickel-base superalloy group, the thermoelectric potential correlated with hardener content in the alloy structure. For solid-solution-type alloys, no problems were found with thermoelectric stability to 1000; for precipitation-hardenable alloys, thermoelectric stability was dependent on phase stability. The effects of the compositional range of alloy constituents on temperature measurement uncertainty are discussed.

Improved interface growth and enhanced flux pinning in YBCO films deposited on an advanced IBAD-MgO based template

NASA Astrophysics Data System (ADS)

Khan, M. Z.; Zhao, Y.; Wu, X.; Malmivirta, M.; Huhtinen, H.; Paturi, P.

2018-02-01

The growth mechanism is studied from the flux pinning point of view in small-scale YBa2Cu3O6+x (YBCO) thin films deposited on a polycrystalline hastelloy with advanced IBAD-MgO based buffer layer architecture. When compared the situation with YBCO films grown on single crystal substrates, the most critical issues that affect the suitable defect formation and thus the optimal vortex pinning landscape, have been studied as a function of the growth temperature and the film thickness evolution. We can conclude that the best critical current property in a wide applied magnetic field range is observed in films grown at relatively low temperature and having intermediate thickness. These phenomena are linked to the combination of the improved interface growth, to the film thickness related crystalline relaxation and to the formation of linear array of edge dislocations that forms the low-angle grain boundaries through the entire film thickness and thus improve the vortex pinning properties. Hence, the optimized buffer layer structure proved to be particularly suitable for new coated conductor solutions.

Development, Demonstration, and Analysis of an Integrated Iodine Hall Thruster Feed System

NASA Technical Reports Server (NTRS)

Polzin, Kurt A.; Peeples, Steven R.; Burt, Adam O.; Martin, Adam K.; Martinez, Armando; Seixal, Joao F.; Mauro, Stephanie

2016-01-01

The design of an in-space iodine-vapor-fed Hall effect thruster propellant management system is described. The solid-iodine propellant tank has unique issues associated with the microgravity environment, requiring a solution where the iodine is maintained in intimate thermal contact with the heated tank walls. The flow control valves required alterations from earlier iterations to survive for extended periods of time in the corrosive iodine-vapor environment. Materials have been selected for the entire feed system that can chemically resist the iodine vapor, with the design now featuring Hastelloy or Inconel for almost all the wetted components. An integrated iodine feed system/Hall thruster demonstration unit was fabricated and tested, with all control being handled by an onboard electronics card specifically designed to operate the feed system. Structural analysis shows that the feed system can survive launch loads after the implementation of some minor reinforcement. Flow modeling, while still requiring significant additional validation, is presented to show its potential in capturing the behavior of components in this low-flow, low-pressure system.

Tensile and Creep Property Characterization of Potential Brayton Cycle Impeller and Duct Materials

NASA Technical Reports Server (NTRS)

Gabb, Timothy P.; Gayda, John

2006-01-01

This paper represents a status report documenting the work on creep of superalloys performed under Project Prometheus. Cast superalloys have potential applications in space as impellers within closed-loop Brayton cycle nuclear power generation systems. Likewise wrought superalloys are good candidates for ducts and heat exchangers transporting the inert working gas in a Brayton-based power plant. Two cast superalloys, Mar-M247LC and IN792, and a NASA GRC powder metallurgy superalloy, LSHR, are being screened to compare their respective capabilities for impeller applications. Several wrought superalloys including Hastelloy X, (Haynes International, Inc., Kokomo, IN), Inconel 617, Inconel 740, Nimonic 263, and Incoloy MA956 (Special Metals Corporation, Huntington, WV) are also being screened to compare their capabilities for duct applications. These proposed applications would require sufficient strength and creep resistance for long term service at temperatures up to 1200 K, with service times to 100,000 h or more. Conventional tensile and creep tests were performed at temperatures up to 1200 K on specimens extracted from the materials. Initial microstructure evaluations were also undertaken.

The VRT gas turbine combustor - Phase II

NASA Technical Reports Server (NTRS)

Melconian, Jerry O.; Mongia, Hukam C.; Nguyen, Hung L.

1992-01-01

An innovative annular combustor configuration is being developed for aircraft and other gas turbine engines. This design has the potential of permitting higher turbine inlet temperatures by reducing the pattern factor and providing a major reduction in NO(x) emission. The design concept is based on a Variable Residence Time (VRT) technique which allows large fuel particles adequate time to completely burn in the circumferentially mixed primary zone. High durability of the combustor is achieved by dual-function use of the incoming air. In Phase I, the feasibility of the concept was demonstrated by water analogue tests and 3D computer modeling. The flow pattern within the combustor was as predicted. The VRT combustor uses only half the number of fuel nozzles of the conventional configuration. In Phase II, hardware was designed, procured, and tested under conditions simulating typical supersonic civil aircraft cruise conditions to the limits of the rig. The test results confirmed many of the superior performance predictions of the VRT concept. The Hastelloy X liner showed no signs of distress after nearly six hours of tests using JP5 fuel.

THE FAILURE OF STRUCTURAL METALS SUBJECTED TO STRAIN-CYCLING CONDITIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Swindeman, R.W.; Douglas, D.A.

1958-11-01

Data showing the isothermal strain-cycling capacity of three metals, inconel, Hastelloy "B," and beryllium, are presented. It is noted that at frequencies of 0.5 cycles per minute the data satisfied am equation of the form N/ sup alpha / epsilon /sub p/ = K, where N is the number of cycles to failure, epsilon /sub p/ is the plastic strain per cycle, and alpha and K are constants whose values depend on the structure and test conditions. Data on Ihconel are given to establish the effect of grain size, specimen geometry, temperature, and frequency. It is found that at temperaturesmore » above 1300 F, grain sine amd frequency exert a pronounced effect on the rupture life. Fine-gralned metal survives more cycles before failure than coarsegrained material. Lomg time cycles shorten the number of cycles to failure when the strain per cycle is low. Thermal strain cycling dain for ihconel are compared to strain cycling data at the same mean temperature. Good correlation is found to exist between the two types of data. (auth)« less

Surface Nb-ALLOYING on 0.4C-13Cr Stainless Steel: Microstructure and Tribological Behavior

NASA Astrophysics Data System (ADS)

Yu, Shengwang; You, Kai; Liu, Xiaozhen; Zhang, Yihui; Wang, Zhenxia; Liu, Xiaoping

2016-02-01

0.4C-13Cr stainless steel was alloyed with niobium using double glow plasma surface alloying and tribological properties of Nb-alloyed steel such as hardness, friction and wear were measured. Effects of the alloying temperature on microstructure and the tribological behavior of the alloyed steel were investigated compared with untreated steel. Formation mechanisms of Nb-alloyed layers and increased wear resistance were also studied. The result shows that after surface Nb-alloying treatment, the 0.4C-13Cr steel exhibits a diffusion adhesion at the alloyed layer/substrate interface and improved tribological property. The friction coefficient of Nb-alloyed steel is decreased by about 0.3-0.45 and the wear rate after Nb-alloying is only 2-5% of untreated steel.

On Nb Silicide Based Alloys: Alloy Design and Selection.

PubMed

Tsakiropoulos, Panos

2018-05-18

The development of Nb-silicide based alloys is frustrated by the lack of composition-process-microstructure-property data for the new alloys, and by the shortage of and/or disagreement between thermodynamic data for key binary and ternary systems that are essential for designing (selecting) alloys to meet property goals. Recent publications have discussed the importance of the parameters δ (related to atomic size), Δχ (related to electronegativity) and valence electron concentration (VEC) (number of valence electrons per atom filled into the valence band) for the alloying behavior of Nb-silicide based alloys (J Alloys Compd 748 (2018) 569), their solid solutions (J Alloys Compd 708 (2017) 961), the tetragonal Nb₅Si₃ (Materials 11 (2018) 69), and hexagonal C14-NbCr₂ and cubic A15-Nb₃X phases (Materials 11 (2018) 395) and eutectics with Nb ss and Nb₅Si₃ (Materials 11 (2018) 592). The parameter values were calculated using actual compositions for alloys, their phases and eutectics. This paper is about the relationships that exist between the alloy parameters δ, Δχ and VEC, and creep rate and isothermal oxidation (weight gain) and the concentrations of solute elements in the alloys. Different approaches to alloy design (selection) that use property goals and these relationships for Nb-silicide based alloys are discussed and examples of selected alloy compositions and their predicted properties are given. The alloy design methodology, which has been called NICE (Niobium Intermetallic Composite Elaboration), enables one to design (select) new alloys and to predict their creep and oxidation properties and the macrosegregation of Si in cast alloys.

On Nb Silicide Based Alloys: Alloy Design and Selection

PubMed Central

Tsakiropoulos, Panos.

2018-01-01

The development of Nb-silicide based alloys is frustrated by the lack of composition-process-microstructure-property data for the new alloys, and by the shortage of and/or disagreement between thermodynamic data for key binary and ternary systems that are essential for designing (selecting) alloys to meet property goals. Recent publications have discussed the importance of the parameters δ (related to atomic size), Δχ (related to electronegativity) and valence electron concentration (VEC) (number of valence electrons per atom filled into the valence band) for the alloying behavior of Nb-silicide based alloys (J Alloys Compd 748 (2018) 569), their solid solutions (J Alloys Compd 708 (2017) 961), the tetragonal Nb5Si3 (Materials 11 (2018) 69), and hexagonal C14-NbCr2 and cubic A15-Nb3X phases (Materials 11 (2018) 395) and eutectics with Nbss and Nb5Si3 (Materials 11 (2018) 592). The parameter values were calculated using actual compositions for alloys, their phases and eutectics. This paper is about the relationships that exist between the alloy parameters δ, Δχ and VEC, and creep rate and isothermal oxidation (weight gain) and the concentrations of solute elements in the alloys. Different approaches to alloy design (selection) that use property goals and these relationships for Nb-silicide based alloys are discussed and examples of selected alloy compositions and their predicted properties are given. The alloy design methodology, which has been called NICE (Niobium Intermetallic Composite Elaboration), enables one to design (select) new alloys and to predict their creep and oxidation properties and the macrosegregation of Si in cast alloys. PMID:29783707

Errors in measurements by ultrasonic thickness gauges caused by the variation in ultrasonic velocity in constructional steels and metal alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kalinin, V.A.; Tarasenko, V.L.; Tselser, L.B.

1988-09-01

Numerical values of the variation in ultrasonic velocity in constructional metal alloys and the measurement errors related to them are systematized. The systematization is based on the measurement results of the group ultrasonic velocity made in the All-Union Scientific-Research Institute for Nondestructive Testing in 1983-1984 and also on the measurement results of the group velocity made by various authors. The variations in ultrasonic velocity were systematized for carbon, low-alloy, and medium-alloy constructional steels; high-alloy iron base alloys; nickel-base heat-resistant alloys; wrought aluminum constructional alloys; titanium alloys; and cast irons and copper alloys.

Alloy hardening and softening in binary molybdenum alloys as related to electron concentration

NASA Technical Reports Server (NTRS)

Stephens, J. R.; Witzke, W. R.

1972-01-01

An investigation was conducted to determine the effects of alloy additions of hafnium, tantalum, tungsten, rhenium, osmium, iridium, and platinum on hardness of molybdenum. Special emphasis was placed on alloy softening in these binary molybdenum alloys. Results showed that alloy softening was produced by those elements having an excess of s+d electrons compared to molybdenum, while those elements having an equal number or fewer s+d electrons that molybdenum failed to produce alloy softening. Alloy softening and alloy hardening can be correlated with the difference in number of s+d electrons of the solute element and molybdenum.

Functionally Graded Metal-Metal Composite Structures

NASA Technical Reports Server (NTRS)

Brice, Craig A. (Inventor)

2017-01-01

Methods and devices are disclosed for creating a multiple alloy composite structure by forming a three-dimensional arrangement of a first alloy composition in which the three-dimensional arrangement has a substantially open and continuous porosity. The three-dimensional arrangement of the first alloy composition is infused with at least a second alloy composition, where the second alloy composition comprises a shape memory alloy. The three-dimensional arrangement is consolidated into a fully dense solid structure, and the original shape of the second alloy composition is set for reversible transformation. Strain is applied to the fully dense solid structure, which is treated with heat so that the shape memory alloy composition becomes memory activated to recover the original shape. An interwoven composite of the first alloy composition and the memory-activated second alloy composition is thereby formed in the multiple alloy composite structure.

Effect of different alloyed layers on the high temperature oxidation behavior of newly developed Ti 2AlNb-based alloys

NASA Astrophysics Data System (ADS)

Wu, Hongyan; Zhang, Pingze; Zhao, Haofeng; Wang, Ling; Xie, Aigen

2011-01-01

The application of titanium aluminide orthorhombic alloys (O-phase alloys) as potential materials in aircraft and jet engines was limited by their poor oxidation resistance at high temperature. The Ti 2AlNb-based alloys were chromised (Cr), chromium-tungstened (Cr-W) and nickel-chromised (Ni-Cr) by the double glow plasma surface alloying process to improve their high temperature oxidation resistance. The discontinuous oxidative behavior of Cr, Cr-W and Ni-Cr alloyed layers on Ti 2AlNb-based alloy at 1093 K was explored in this study. After exposing at 1093 K, the TiO 2 layer was formed on the bare alloy and accompanied by the occurrence of crack, which promoted oxidation rate. The oxidation behavior of Ti 2AlNb-based alloys was improved by surface alloying due to the formation of protective Al 2O 3 scale or continuous and dense NiCr 2O 4 film. The Ni-Cr alloyed layer presented the best high-temperature oxidation resistance among three alloyed layers.

Warm Temperature Deformation Behavior and Processing Maps of 5182 and 7075 Aluminum Alloy Sheets with Fine Grains

NASA Astrophysics Data System (ADS)

Jang, D. H.; Kim, W. J.

2018-05-01

The tensile deformation behavior and processing maps of commercial 5182 and 7075 aluminum alloy sheets with similarly fine grain sizes (about 8 μm) were examined and compared over the temperature range of 423-723 K. The 5182 aluminum alloy with equiaxed grains exhibited larger strain rate sensitivity exponent ( m) values than the 7075 aluminum alloy with elongated grains under most of the testing conditions. The fracture strain behaviors of the two alloys as a function of strain rate and temperature followed the trend in their m values. In the processing maps, the power dissipation parameter values of the 5182 aluminum alloy were larger than those of the 7075 aluminum alloy and the instability domains of the 5182 aluminum alloy were smaller compared to that of the 7075 aluminum alloy, implying that the 5182 aluminum alloy had a better hot workability than the 7075 aluminum alloy.

Adhesion, friction, and wear of binary alloys in contact with single-crystal silicon carbide

NASA Technical Reports Server (NTRS)

Miyoshi, K.; Buckley, D. H.

1980-01-01

Sliding friction experiments, conducted with various iron base alloys (alloying elements are Ti, Cr, Mn, Ni, Rh and W) in contact with a single crystal silicon carbide /0001/ surface in vacuum are discussed. Results indicate atomic size misfit and concentration of alloying elements play a dominant role in controlling adhesion, friction, and wear properties of iron-base binary alloys. The controlling mechanism of the alloy properties is as an intrinsic effect involving the resistance to shear fracture of cohesive bonding in the alloy. The coefficient of friction generally increases with an increase in solute concentration. The coefficient of friction increases as the solute-to-iron atomic radius ratio increases or decreases from unity. Alloys having higher solute concentration produce more transfer to silicon carbide than do alloys having low solute concentrations. The chemical activity of the alloying element is also an important parameter in controlling adhesion and friction of alloys.

Fatigue of die cast zinc alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schrems, K.K.; Dogan, O.N.; Goodwin, F.E.

2006-04-01

The rotating bending fatigue limit of die cast zinc alloy 2, alloy 3, alloy 5, AcuZinc 5, and ZA-8 were determined as a part of an on-going program by ILZRO into the mechanical properties of die cast zinc. The stress-life (S-N) curves of alloys 3, 5, AcuZinc 5, and ZA-8 were determined previously. This presentation reports the results of the S-N curve for Alloy 2 and the calculated fatigue limits for all five alloys. During the previous stress-life testing, the samples were stopped at 10 million cycles and the fatigue limit for alloy 3, alloy 5, and AcuZinc 5 appearedmore » to be higher and the fatigue limit for ZA-8 appeared to be lower than the values reported in the literature. This was further investigated in alloy 5 and ZA-8 by testing continuous cast bulk alloy 5 and ZA-8.« less

Evaluation and comparison of castability between an indigenous and imported Ni-Cr alloy.

PubMed

Ramesh, Ganesh; Padmanabhan, T V; Ariga, Padma; Subramanian, R

2011-01-01

Since 1907 casting restorations have been in use in dentistry. Numerous companies have been manufacturing and marketing base metal alloys. Gold was a major component of casting alloys. But alloys with less than 65% gold tarnished easily and the increase in cost of gold post-1970s lead to the revival of base metal alloys such as nickel-chromium and cobalt-chromium alloys which were in use since 1930s. This study was conducted to evaluate and compare the castability between an indigenous alloy and an imported alloy, as imported base metal alloys are considered to be expensive for fabrication of crowns and bridges. This study was conducted to evaluate and compare the castability (for the accurate fabrication of crowns and bridges) between an indigenous base metal alloy-Non-ferrous Materials Technology Development Centre (NFTDC), Hyderabad (Alloy A) -and an imported base metal alloys (Alloy B). Castability measurement was obtained by counting the number of completely formed line segments surrounding the 81 squares in the pattern and later calculating the percentage values. The percentage obtained was taken as the castability value for a particular base metal alloy. The percentage of castability was determined by counting only the number of completely cast segments in a perfect casting (81 × 2 = 162), and then multiplying the resulting fraction by 100 to give the percentage completeness. The Student t-test was used. When the castability of alloys A and B was compared, the calculated value was less than the tabular value (1.171 < 2.048) leading to the conclusion that castability between alloys A and B is insignificant. Therefore we conclude that both the alloys have the same castability. Using the above-mentioned materials and following the method to test castability, we were able to derive favorable results. As the results were satisfactory, we can conclude that the castability of the indigenous alloy is on par with the imported alloy.

Differences between orthopaedic evaluation and radiological reports of conventional radiographs in patients with minor trauma admitted to the emergency department.

PubMed

Catapano, Michele; Albano, Domenico; Pozzi, Grazia; Accetta, Riccardo; Memoria, Sergio; Pregliasco, Fabrizio; Messina, Carmelo; Sconfienza, Luca Maria

2017-11-01

During night and on weekends, in our emergency department there is no radiologist on duty or on call: thus, X-ray examinations (XR) are evaluated by the orthopaedic surgeon on duty and reported the following morning/monday by radiologists. The aim of our study was to examine the discrepancy rate between orthopaedists and radiologists in the interpretation of imaging examinations performed on patients in our tertiary level orthopaedic institution and the consequences of delayed diagnosis in terms of patient management and therapeutic strategy. We retrospectively reviewed all cases of discrepancy between orthopaedists and radiologists, which were categorized according to anatomical location of injury, initial diagnosis and treatment, change in diagnosis and treatment. We used the Chi square test to compare the frequencies of discrepancies between patients ≤14 and >14years of age. From January to December 2016, 19,512 patients admitted to our emergency department performed at least an imaging examination; among these patients, 13,561 underwent XR in absence of an attending radiologist. A discrepant diagnosis was found in 337/13,561 (2.5%; 184 males; mean age: 36.7±23.7, range 2-95); 151/337 (45%) discrepancies were encountered in the lower limbs, with ankle being the most common site of misdiagnosis (64/151), and 103/337 (30%) in the upper limbs, with the elbow being the most frequent site in this district (35/103). We found 293/337 false negatives (87%) and 44/337 false positives (13%), with 134 and 13 patients needing treatment change, respectively. We found 85/337 discrepancies (25%) in patients ≤14 years of age, and 252/337 (75%) in those >14years. The distribution of discrepancies per anatomic district was significantly different (P<0.001) in these two groups of patients. A low rate of discrepancy between orthopaedists and radiologists in evaluating images of patients admitted to our emergency department was found, although treatment change occurred in about half of cases. A thorough and accurate clinical evaluation is crucial to provide a correct treatment and prognosis. Copyright © 2017 Elsevier Ltd. All rights reserved.

Experimental study on impact-induced seismic wave propagating through quartz sand simulating asteroid regolith

NASA Astrophysics Data System (ADS)

Matsue, Kazuma; Arakawa, Masahiko; Yasui, Minami; Matsumoto, Rie; Tsujido, Sayaka; Takano, Shota; Hasegawa, Sunao

2015-08-01

Introduction: Recent spacecraft surveys clarified that asteroid surfaces were covered with regolith made of boulders and pebbles such as that found on the asteroid Itokawa. It was also found that surface morphologies of asteroids formed on the regolith layer were modified. For example, the high-resolution images of the asteroid Eros revealed the evidence of the downslope movement of the regolith layer, then it could cause the degradation and the erasure of small impact crater. One possible process to explain these observations is the regolith layer collapse caused by seismic vibration after projectile impacts. The impact-induced seismic wave might be an important physical process affecting the morphology change of regolith layer on asteroid surfaces. Therefore, it is significant for us to know the relationship between the impact energy and the impact-induced seismic wave. So in this study, we carried out impact cratering experiments in order to observe the seismic wave propagating through the target far from the impact crater.Experimental method: Impact cratering experiments were conducted by using a single stage vertical gas gun set at Kobe Univ and a two-stage vertical gas gun set at ISAS. We used quartz sands with the particle diameter of 500μm, and the bulk density of 1.48g/cm3. The projectile was a ball made of polycarbonate with the diameter of 4.75mm and aluminum, titan, zirconia, stainless steel, cupper, tungsten carbide projectile with the diameter of 2mm. These projectiles were launched at the impact velocity from 0.2 to 7km/s. The target was set in a vacuum chamber evacuated below 10 Pa. We measured the seismic wave by using a piezoelectric uniaxial accelerometer.Result: The impact-induced seismic wave was measured to show a large single peak and found to attenuate with the propagation distance. The maximum acceleration of the seismic wave was recognized to have a good relationship with the normalized distance x/R, where x is the propagation distance and R is the crater radius, irrespective of the impact velocities: gmax = 160(x/R)-2.98.

Structural Dynamics and Evolution of Bismuth Electrodes during Electrochemical Reduction of CO 2 in Imidazolium-Based Ionic Liquid Solutions

DOE PAGES

Medina-Ramos, Jonnathan; Lee, Sang Soo; Fister, Timothy T.; ...

2017-09-12

Real-time changes in the composition and structure of bismuth electrodes used for catalytic conversion of CO 2 into CO were examined via X-ray absorption spectroscopy (including XANES and EXAFS), electrochemical quartz crystal microbalance (EQCM) and in situ X-ray reflectivity (XR). Measurements were performed with bismuth electrodes immersed in acetonitrile (MeCN) solutions containing a 1-butyl-3-methylimidazolium ([BMIM] +) ionic liquid promoter or electrochemically inactive tetrabutylammonium supporting electrolytes (TBAPF 6 or TBAOTf). Altogether, these measurements show that bismuth electrodes are originally a mixture of bismuth oxides (including Bi 2O 3) and metallic bismuth (Bi 0), and that the reduction of oxidized bismuth speciesmore » to Bi 0 is fully achieved under potentials at which CO 2 activation takes place. Furthermore, EQCM measurements conducted during cyclic voltammetry revealed that a bismuth-coated quartz crystal exhibits significant shifts in resistance (ΔR) prior to the onset of CO 2 reduction near -1.75 V vs. Ag/AgCl and pronounced hysteresis in frequency (Δf) and ΔR, which suggests significant changes in roughness or viscosity at the Bi/[BMIM] + solution interface. In situ XR performed on rhombohedral Bi (001) oriented films indicates extensive restructuring of the bismuth film cathodes takes place upon polarization to potentials more negative than -1.6 V vs. Ag/AgCl, which is characterized by a decrease of the Bi (001) Bragg peak intensity of ≥50% in [BMIM]OTf solutions in the presence and absence of CO 2. Over 90% of the reflectivity is recovered during the anodic half-scan, suggesting that the structural changes are mostly reversible. By contrast, such a phenomenon is not observed for thin Bi (001) oriented films in solutions of tetrabutylammonium salts that do not promote CO 2 reduction. In conclusion, these results highlight that Bi electrodes undergo significant potential-dependent chemical and structural transformations in the presence of [BMIM] + based electrolytes, including the reduction of bismuth oxide to bismuth metal, changes in roughness and near-surface viscosity.« less

A review on magnesium alloys as biodegradable materials

NASA Astrophysics Data System (ADS)

Gu, Xue-Nan; Zheng, Yu-Feng

2010-06-01

Magnesium alloys attracted great attention as a new kind of degradable biomaterials. One research direction of biomedical magnesium alloys is based on the industrial magnesium alloys system, and another is the self-designed biomedical magnesium alloys from the viewpoint of biomaterials. The mechanical, biocorrosion properties and biocompatibilities of currently reported Mg alloys were summarized in the present paper, with the mechanical properties of bone tissue, the healing period postsurgery, the pathophysiology and toxicology of the alloying elements being discussed. The strategy in the future development of biomedical Mg alloys was proposed.

Alloy materials

DOEpatents

Hans Thieme, Cornelis Leo; Thompson, Elliott D.; Fritzemeier, Leslie G.; Cameron, Robert D.; Siegal, Edward J.

2002-01-01

An alloy that contains at least two metals and can be used as a substrate for a superconductor is disclosed. The alloy can contain an oxide former. The alloy can have a biaxial or cube texture. The substrate can be used in a multilayer superconductor, which can further include one or more buffer layers disposed between the substrate and the superconductor material. The alloys can be made a by process that involves first rolling the alloy then annealing the alloy. A relatively large volume percentage of the alloy can be formed of grains having a biaxial or cube texture.

High temperature mechanical properties of a zirconium-modified, precipitation- strengthened nickel, 30 percent copper alloy

NASA Technical Reports Server (NTRS)

Whittenberger, J. D.

1974-01-01

A precipitation-strengthened Monel-type alloy has been developed through minor alloying additions of zirconium to a base Ni-30Cu alloy. The results of this exploratory study indicate that thermomechanical processing of a solution-treated Ni-30Cu-0.2Zr alloy produced a dispersion of precipitates. The precipitates have been tentatively identified as a Ni5Zr compound. A comparison of the mechanical properties, as determined by testing in air, of the zirconium-modified alloy to those of a Ni-30Cu alloy reveals that the precipitation-strengthened alloy has improved tensile properties to 1200 K and improved stress-rupture properties to 1100 K. The oxidation characteristics of the modified alloy appeared to be equivalent to those of the base Ni-30Cu alloy.

Bond strength of luting cement to casting and soldering alloy.

PubMed

Kumbuloglu, O; Lassila, L V J; User, A; Toksavul, S; Vallittu, P K

2006-03-01

Adjustment of metal alloy framework of the porcelain-fused-to-metal crown by soldering minor marginal deficiences prior insertion may sometimes be needed. The aim of this study was to compare shear bond strengths of four luting cements to casting metal alloy and soldering metal alloy. A total of 64 flame cast non-precious metal alloy and flame soldered metal alloy samples were used. Durelon, Panavia F, RelyX Unicem Applicap and RelyX ARC stubs were bonded to the alloy substrate surface. After stored in water at 37 degrees C for 1 week, shear bond strength of the cement to the alloy was measured. Differences were analyzed using one way ANOVA (p<0.05). There were no difference between the cast metal alloy and soldering metal alloy substrate.

Size-confined fixed-composition and composition-dependent engineered band gap alloying induces different internal structures in L-cysteine-capped alloyed quaternary CdZnTeS quantum dots

NASA Astrophysics Data System (ADS)

Adegoke, Oluwasesan; Park, Enoch Y.

2016-06-01

The development of alloyed quantum dot (QD) nanocrystals with attractive optical properties for a wide array of chemical and biological applications is a growing research field. In this work, size-tunable engineered band gap composition-dependent alloying and fixed-composition alloying were employed to fabricate new L-cysteine-capped alloyed quaternary CdZnTeS QDs exhibiting different internal structures. Lattice parameters simulated based on powder X-ray diffraction (PXRD) revealed the internal structure of the composition-dependent alloyed CdxZnyTeS QDs to have a gradient nature, whereas the fixed-composition alloyed QDs exhibited a homogenous internal structure. Transmission electron microscopy (TEM) and dynamic light scattering (DLS) analysis confirmed the size-confined nature and monodispersity of the alloyed nanocrystals. The zeta potential values were within the accepted range of colloidal stability. Circular dichroism (CD) analysis showed that the surface-capped L-cysteine ligand induced electronic and conformational chiroptical changes in the alloyed nanocrystals. The photoluminescence (PL) quantum yield (QY) values of the gradient alloyed QDs were 27-61%, whereas for the homogenous alloyed QDs, the PL QY values were spectacularly high (72-93%). Our work demonstrates that engineered fixed alloying produces homogenous QD nanocrystals with higher PL QY than composition-dependent alloying.

Evaluation of Surface Roughness and Tensile Strength of Base Metal Alloys Used for Crown and Bridge on Recasting (Recycling).

PubMed

Agrawal, Amit; Hashmi, Syed W; Rao, Yogesh; Garg, Akanksha

2015-07-01

Dental casting alloys play a prominent role in the restoration of the partial dentition. Casting alloys have to survive long term in the mouth and also have the combination of structure, molecules, wear resistance and biologic compatibility. According to ADA system casting alloys were divided into three groups (wt%); high noble, Noble and predominantly base metal alloys. To evaluate the mechanical properties such as tensile strength and surface roughness of the new and recast base metal (nickel-chromium) alloys. Recasting of the base metal alloys derived from sprue and button, to make it reusable has been done. A total of 200 test specimens were fabricated using specially fabricated jig of metal and divided into two groups- 100 specimens of new alloy and 100 specimens of recast alloys, which were tested for tensile strength on universal testing machine and surface roughness on surface roughness tester. Tensile strength of new alloy showed no statistically significant difference (p-value>0.05) from recast alloy whereas new alloy had statistically significant surface roughness (Maximum and Average surface roughness) difference (p-value<0.01) as compared to recast alloy. Within the limitations of the study it is concluded that the tensile strength will not be affected by recasting of nickel-chromium alloy whereas surface roughness increases markedly.

Model for the Prediction of the Hydriding Thermodynamics of Pd-Rh-Co Ternary Alloys

DOE Office of Scientific and Technical Information (OSTI.GOV)

Teter, D.F.; Thoma, D.J.

1999-03-01

A dilute solution model (with respect to the substitutional alloying elements) has been developed, which accurately predicts the hydride formation and decomposition thermodynamics and the storage capacities of dilute ternary Pd-Rh-Co alloys. The effect of varying the rhodium and cobalt compositions on the thermodynamics of hydride formation and decomposition and hydrogen capacity of several palladium-rhodium-cobalt ternary alloys has been investigated using pressure-composition (PC) isotherms. Alloying in the dilute regime (<10 at.%) causes the enthalpy for hydride formation to linearly decrease with increasing alloying content. Cobalt has a stronger effect on the reduction in enthalpy than rhodium for equivalent alloying amounts.more » Also, cobalt reduces the hydrogen storage capacity with increasing alloying content. The plateau thermodynamics are strongly linked to the lattice parameters of the alloys. A near-linear dependence of the enthalpy of hydride formation on the lattice parameter was observed for both the binary Pd-Rh and Pd-Co alloys, as well as for the ternary Pd-Rh-Co alloys. The Pd-5Rh-3Co (at. %) alloy was found to have similar plateau thermodynamics as a Pd-10Rh alloy, however, this ternary alloy had a diminished hydrogen storage capacity relative to Pd-10Rh.« less

Effect of nitrogen on iron-manganese-based shape memory alloys

NASA Astrophysics Data System (ADS)

Ariapour, Azita

Shape memory effect is due to a reversible martensitic transformation. The major drawback in case of Fe-Mn-based shape memory alloys is their inferior shape memory effect compared to Ni-Ti and Cu-based shape memory alloys and their low strength and corrosion resistance compared to steel alloys. It is known that by increasing the alloy strength the shape memory effect can be improved. Nitrogen in solid solution can increase the strength of steels to a greater extent than other major alloying elements. However, its effect on shape memory effect of Fe-Mn-based alloys is ambiguous. In this work first we investigated the effect of nitrogen addition in solid solution on both shape memory effect (SME) and strength of a Fe-Mn-Cr-Ni-Si shape memory alloy (SMA). It was found that interstitial nitrogen suppressed the shape memory effect in these alloys. As an example addition of 0.24 wt % nitrogen in solid solution to the alloy system suppressed the SME by ˜80% and increased the strength by 20%. A reduction of martensitic phase formation was found to be the dominant factor in suppression of the SME. This was related, experimentally and theoretically to stacking fault energy of the alloy as well as the driving force and friction force during the transformation. The second approach was doping the alloy with both 0.36 wt% of nitrogen and 0.36 wt% of niobium. Niobium has great affinity for nitrogen and thus NbN dispersed particles can be produced in the alloy following hot rolling. Then particles prevent growth of the alloy and increase the strength of the alloy due to reduced grain size, and precipitation hardening. The improvement of SME in this alloy compared to the interstitial containing alloys was due to the large removal of the nitrogen from solid solution. In case of all the alloys studied in this work, the presence of nitrogen in solid solution improved the corrosion resistance of the alloy. This suggests that nitrogen can replace nickel in the alloy. One of the proposed applications for high strength Fe-Mn-based alloys is as tendon rods in prestressed concrete. The advantage of M alloys in this application is the possibility of producing curved structural prestressed concrete.

Imparting passivity to vapor deposited magnesium alloys

NASA Astrophysics Data System (ADS)

Wolfe, Ryan C.

Magnesium has the lowest density of all structural metals. Utilization of low density materials is advantageous from a design standpoint, because lower weight translates into improved performance of engineered products (i.e., notebook computers are more portable, vehicles achieve better gas mileage, and aircraft can carry more payload). Despite their low density and high strength to weight ratio, however, the widespread implementation of magnesium alloys is currently hindered by their relatively poor corrosion resistance. The objective of this research dissertation is to develop a scientific basis for the creation of a corrosion resistant magnesium alloy. The corrosion resistance of magnesium alloys is affected by several interrelated factors. Among these are alloying, microstructure, impurities, galvanic corrosion effects, and service conditions, among others. Alloying and modification of the microstructure are primary approaches to controlling corrosion. Furthermore, nonequilibrium alloying of magnesium via physical vapor deposition allows for the formation of single-phase magnesium alloys with supersaturated concentrations of passivity-enhancing elements. The microstructure and surface morphology is also modifiable during physical vapor deposition through the variation of evaporation power, pressure, temperature, ion bombardment, and the source-to-substrate distance. Aluminum, titanium, yttrium, and zirconium were initially chosen as candidates likely to impart passivity on vapor deposited magnesium alloys. Prior to this research, alloys of this type have never before been produced, much less studied. All of these metals were observed to afford some degree of corrosion resistance to magnesium. Due to the especially promising results from nonequilibrium alloying of magnesium with yttrium and titanium, the ternary magnesium-yttrium-titanium system was investigated in depth. While all of the alloys are lustrous, surface morphology is observed under the scanning electron microscope. The corrosion rate of the nonequilibrium sputtered alloys, as determined by polarization resistance, is significantly reduced compared to the most corrosion resistant commercial magnesium alloys. The open circuit potentials of the sputter deposited alloys are significantly more noble compared to commercial, equilibrium phase magnesium alloys. Galvanic corrosion susceptibility has also been considerably reduced. Nonequilibrium magnesium-yttrium-titanium alloys have been shown to achieve passivity autonomously by alteration of the composition chemistry of the surface oxide/hydroxide layer. Self-healing properties are also evident, as corrosion propagation can be arrested after initial pitting of the material. A clear relationship exists between the corrosion resistance of sputter vapor deposited magnesium alloys and the amount of ion bombardment incurred by the alloy during deposition. Argon pressure, the distance between the source and the substrate, and alloy morphology play important roles in determining the ability of the alloy to develop a passive film. Thermal effects, both during and after alloy deposition, alter the stress state of the alloys, precipitation of second phases, and the mechanical stability of the passive film. An optimal thermal treatment has been developed in order to maximize the corrosion resistance of the magnesium-yttrium-titanium alloys. The significance of the results includes the acquisition of electrochemical data for these novel materials, as well as expanding the utilization of magnesium alloys by the improvement in their corrosion resistance. The magnesium alloys developed in this work are more corrosion resistant than any commercial magnesium alloy. Structural components comprised of these alloys would therefore exhibit unprecedented corrosion performance. Coatings of these alloys on magnesium components would provide a corrosion resistant yet galvanically-compatible coating. The broad impact of these contributions is that these new low-density, corrosion resistant magnesium alloys can be used to produce engineering components for vehicles that have greater acceleration, longer range, heavier payloads, lower life cycle costs, and longer inspection intervals.

Effects of chemical composition on the corrosion of dental alloys.

PubMed

Galo, Rodrigo; Ribeiro, Ricardo Faria; Rodrigues, Renata Cristina Silveira; Rocha, Luís Augusto; de Mattos, Maria da Glória Chiarello

2012-01-01

The aim of this study was to determine the effect of the oral environment on the corrosion of dental alloys with different compositions, using electrochemical methods. The corrosion rates were obtained from the current-potential curves and electrochemical impedance spectroscopy (EIS). The effect of artificial saliva on the corrosion of dental alloys was dependent on alloy composition. Dissolution of the ions occurred in all tested dental alloys and the results were strongly dependent on the general alloy composition. Regarding the alloys containing nickel, the Ni-Cr and Ni-Cr-Ti alloys released 0.62 mg/L of Ni on average, while the Co-Cr dental alloy released ions between 0.01 and 0.03 mg/L of Co and Cr, respectively.The open-circuit potential stabilized at a higher level with lower deviation (standard deviation: Ni-Cr-6Ti = 32 mV/SCE and Co-Cr = 54 mV/SCE). The potenciodynamic curves of the dental alloys showed that the Ni-based dental alloy with >70 wt% of Ni had a similar curve and the Co-Cr dental alloy showed a low current density and hence a high resistance to corrosion compared with the Ni-based dental alloys. Some changes in microstructure were observed and this fact influenced the corrosion behavior for the alloys. The lower corrosion resistance also led to greater release of nickel ions to the medium. The quantity of Co ions released from the Co-Cr-Mo alloy was relatively small in the solutions. In addition, the quantity of Cr ions released into the artificial saliva from the Co-Cr alloy was lower than Cr release from the Ni-based dental alloys.

[Metallurgical differentiation of cobalt-chromium alloys for implants].

PubMed

Holzwarth, U; Thomas, P; Kachler, W; Göske, J; Schuh, A

2005-10-01

Cobalt Chromium alloys are used in cemented total hip or knee arthroplasty as well as in metal-on-metal bearings in total hip arthroplasty. An increasing number of publications report about (allergic) reactions to wear particles of Cobalt Chromium alloys. Reactions to nickel are more frequent in comparison to Cobalt or Chromium particles. It is well known that different kinds of Cobalt Chromium alloys contain different amounts of alloying elements; nevertheless. The aim of the current work was to compare the different Cobalt Chromium alloys according to ASTM F or ISO standards in respect to the different alloying elements. Co28Cr6Mo casting alloys according to ASTM F 75 or ISO 5832-4 as well as forging alloy types according to ASTM F 799 and ISO 5832 such as Co20Cr15W10Ni, Co35Ni20Cr, Fe40Co20Cr10Ni, Co20Cr20Ni, and Co28Cr6Mo were analyzed in respect to their element content of Co, Cr, Ni, Mo, Fe, W, and Mn. In 1935 the Cobalt based alloy "Vitallium" Co30Cr5Mo basically used in the aircraft industry was introduced into medicine. The chemical composition of this alloy based on Cobalt showed 30 wt.% Chromium and 5 wt.% Molybdenum. The differentiation using alloy names showed no Nickel information in single alloy names. The information given about different alloys can lead to an unprecise evaluation of histopathological findings in respect to alloys or alloying constituents. Therefore, implant manufacturers should give the exact information about the alloys used and adhere to European law, Euronorm 93/42/EWG.

Effect of cold rolling on microstructure and mechanical property of extruded Mg–4Sm alloy during aging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Rongguang, E-mail: lirongguang1980@126.com; Xin, Renlong; Chapuis, Adrien

Microstructure and mechanical properties of the Mg–4Sm (wt.%) alloy, prepared via combined processes of extrusion, cold rolling and aging, have been investigated. The hot extruded alloy exhibits a weak rare earth magnesium alloy texture with < 11 − 21 >//ED, while the cold-rolled alloy shows a stronger basal texture with < 0001 >//ND. Many tensile twins and double twins are observed in grains after rolling. The cold-rolled alloy shows a weak age-hardening response compared with the extruded alloy, which is the result of more precipitation in the twin boundary during aging. The rolled alloy exhibits almost no precipitate free zonemore » during aging compared with the extruded alloy. The higher proof stress of the rolled alloy in peak-aged condition is attributed to the presence of twin boundaries, stronger basal texture, higher dislocation density, and the suppression of precipitate free zone compared with the extruded alloy. - Highlights: • No precipitate free zone appears in cold-rolled alloy after aging. • Segregation and precipitates are observed in twin boundaries and grain boundaries. • Cold-rolled alloy shows a weak age-hardening response.« less

Iron-based amorphous alloys and methods of synthesizing iron-based amorphous alloys

DOEpatents

Saw, Cheng Kiong; Bauer, William A.; Choi, Jor-Shan; Day, Dan; Farmer, Joseph C.

2016-05-03

A method according to one embodiment includes combining an amorphous iron-based alloy and at least one metal selected from a group consisting of molybdenum, chromium, tungsten, boron, gadolinium, nickel phosphorous, yttrium, and alloys thereof to form a mixture, wherein the at least one metal is present in the mixture from about 5 atomic percent (at %) to about 55 at %; and ball milling the mixture at least until an amorphous alloy of the iron-based alloy and the at least one metal is formed. Several amorphous iron-based metal alloys are also presented, including corrosion-resistant amorphous iron-based metal alloys and radiation-shielding amorphous iron-based metal alloys.

Tensile and creep properties of titanium-vanadium, titanium-molybdenum, and titanium-niobium alloys

NASA Technical Reports Server (NTRS)

Gray, H. R.

1975-01-01

Tensile and creep properties of experimental beta-titanium alloys were determined. Titanium-vanadium alloys had substantially greater tensile and creep strength than the titanium-niobium and titanium-molybdenum alloys tested. Specific tensile strengths of several titanium-vanadium-aluminum-silicon alloys were equivalent or superior to those of commercial titanium alloys to temperatures of 650 C. The Ti-50V-3Al-1Si alloy had the best balance of tensile strength, creep strength, and metallurgical stability. Its 500 C creep strength was far superior to that of a widely used commercial titanium alloy, Ti-6Al-4V, and almost equivalent to that of newly developed commercial titanium alloys.